Loaded MCU 'beacon' 45 commands (Beacon 2.1.0 / )
MCU 'beacon' config: ADC_MAX=4095 BEACON_ACCEL_BITS=12 BEACON_ACCEL_SCALE_16G=7.81 BEACON_ACCEL_SCALE_2G=0.98 BEACON_ACCEL_SCALE_4G=1.95 BEACON_ACCEL_SCALE_8G=3.91 BEACON_ADC_SMOOTH_COUNT=16 BEACON_HAS_ACCEL=1 BEACON_REV=H CLOCK_FREQ=32000000 MCU=beacon STATS_SUMSQ_BASE=256
Configured MCU 'beacon' (0 moves)
===== Config file =====
[mcu rpi]
serial = /tmp/klipper_host_mcu

[board_pins btt-octopus-pro-h723-11]
aliases = 
	
	
	
	x_step_pin=PF13,
	x_dir_pin=PF12,
	x_enable_pin=PF14,
	x_uart_pin=PC4,
	x_diag_pin=PG6,
	x_endstop_pin=PG6,
	
	
	
	dual_carriage_step_pin=PF9,
	dual_carriage_dir_pin=PF10,
	dual_carriage_enable_pin=PG2,
	dual_carriage_uart_pin=PF2,
	dual_carriage_diag_pin=PG12,
	dual_carriage_endstop_pin=PG12,
	
	
	
	y_step_pin=PG0,
	y_dir_pin=PG1,
	y_enable_pin=PF15,
	y_uart_pin=PD11,
	y_diag_pin=PG9,
	y_endstop_pin=PG9,
	
	
	
	y1_step_pin=PG4,
	y1_dir_pin=PC1,
	y1_enable_pin=PA2,
	y1_uart_pin=PC7,
	y1_diag_pin=PG11,
	y1_endstop_pin=PG11,
	
	
	
	z0_step_pin=PC13,
	z0_dir_pin=PF0,
	z0_enable_pin=PF1,
	z0_uart_pin=PE4,
	z0_diag_pin=PG13,
	
	
	
	z1_step_pin=PE2,
	z1_dir_pin=PE3,
	z1_enable_pin=PD4,
	z1_uart_pin=PE1,
	z1_diag_pin=PG14,
	
	
	
	z2_step_pin=PE6,
	z2_dir_pin=PA14,
	z2_enable_pin=PE0,
	z2_uart_pin=PD3,
	z2_diag_pin=PG15,
	
	e_step_pin=PF11,
	e_dir_pin=PG3,
	e_enable_pin=PG5,
	e_uart_pin=PC6,
	
	e_heater_pin=PA2,
	e_sensor_pin=PF4,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=PA7,
	stepper_spi_miso_pin=PA6,
	stepper_spi_sclk_pin=PA5,
	adxl345_cs_pin=PA15,
	bltouch_sensor_pin=PB7,
	bltouch_control_pin=PB6,
	probe_pin=PB7,
	fan_part_cooling_pin=PA8,
	fan_toolhead_cooling_pin=PE5,
	fan_controller_board_pin=PD12,
	heater_bed_heating_pin=PA1,
	heater_bed_sensor_pin=PF3,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PG15,
	filament_sensor_motion_pin=PG14,
	ratrig_vaoc_probe_pin=PG10,
	ratrig_vaoc_led_pin=PB0,
	ratrig_vaoc_fan_pin=PD13,
	chamber_lighting_pin=PB11,
	chamber_filter_4p_fan_pin=PD14,
	chamber_filter_4p_fan_enable_pin=PD15

[mcu]
serial = /dev/RatOS/btt-octopus-pro-h723-11

[temperature_sensor Octopus_Pro_H723_V1.1]
sensor_type = temperature_mcu

[adxl345 controlboard]
cs_pin = PA15
spi_software_mosi_pin = PB5
spi_software_miso_pin = PB4
spi_software_sclk_pin = PB3

[board_pins toolboard_t0]
mcu = toolboard_t0
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t0]
serial = /dev/RatOS/btt-ebb42-gen2-10-t0

[temperature_sensor EBB42_Gen2_v1.0_T0]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t0

[lis2dw toolboard_t0]
axes_map = x, z, y
cs_pin = toolboard_t0:PB1
spi_software_mosi_pin = toolboard_t0:PB11
spi_software_miso_pin = toolboard_t0:PB2
spi_software_sclk_pin = toolboard_t0:PB10

[board_pins toolboard_t1]
mcu = toolboard_t1
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t1]
serial = /dev/RatOS/btt-ebb42-gen2-10-t1

[temperature_sensor EBB42_Gen2_v1.0_T1]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t1

[lis2dw toolboard_t1]
axes_map = x, z, y
cs_pin = toolboard_t1:PB1
spi_software_mosi_pin = toolboard_t1:PB11
spi_software_miso_pin = toolboard_t1:PB2
spi_software_sclk_pin = toolboard_t1:PB10

[gcode_macro RatOS]
variable_homing = "endstops"
variable_z_probe = "static"
variable_sensorless_x_current = 0.6
variable_sensorless_y_current = 0.9
variable_safe_home_x = "middle"
variable_safe_home_y = "middle"
variable_driver_type_x = "tmc2209"
variable_driver_type_y = "tmc2209"
variable_stowable_probe_stop_on_error = False
variable_chamber_filter_enable = True
variable_chamber_filter_speed = 0.5
variable_chamber_filter_disable_speed = 1.0
variable_chamber_filter_enable_at = "after_print_start"
variable_chamber_filter_disable_period = 300
variable_chamber_filter_disable_bed_temp = 0
variable_chamber_heater_enable = True
variable_chamber_heater_bed_temp = 115
variable_chamber_heater_preheating_temp = 150
variable_chamber_heater_heating_temp_offset = 25
variable_chamber_heater_control_external_heater = False
variable_chamber_heater_air_circulation_enable = True
variable_chamber_heater_air_circulation_fan_speed = 0.35
variable_chamber_heater_air_circulation_y_pos = 0
variable_chamber_heater_air_circulation_z_pos = 100
variable_chamber_heater_extra_fan_speed = 1.0
variable_chamber_heater_filter_fan_speed = 1.0
variable_bed_heat_soak_time = 0
variable_hotend_heat_soak_time = 0
variable_led_status_action = 0.0,1.0,1.0
variable_led_status_success = 0.0,1.0,0.0
variable_led_status_error = 1.0,0.0,1.0
variable_led_status_on = 1.0,1.0,1.0
variable_led_status_off = 0.0,0.0,1.0
variable_led_status_standby = 0.1,0.1,0.1
variable_led_status_heating = 1.0,0.0,0.0
variable_led_status_cooling = 0.0,0.0,1.0
variable_calibrate_bed_mesh = True
variable_adaptive_mesh = True
variable_start_print_park_in = "center"
variable_start_print_park_z_height = 3
variable_end_print_park_in = "back"
variable_pause_print_park_in = "back"
variable_end_print_park_z_hop = 20
variable_nozzle_priming = "primeblob"
variable_nozzle_prime_start_x = "max"
variable_nozzle_prime_start_y = "min"
variable_nozzle_prime_direction = "auto"
variable_nozzle_prime_bridge_fan = 102
variable_probe_for_priming_result = None
variable_probe_for_priming_end_result = None
variable_probe_for_priming_result_t1 = None
variable_probe_for_priming_end_result_t1 = None
variable_probe_for_priming_disable_mesh_constraints = False
variable_adaptive_prime_offset_threshold = -1.0
variable_last_z_offset = None
variable_runout_park_in = "front"
variable_enable_unload_tip_forming = False
variable_filament_unload_length = 150
description = RatOS variable storage macro, will echo variables to the console when run.
variable_relative_extrusion = True
variable_force_absolute_position = False
variable_preheat_extruder = True
variable_preheat_extruder_temp = 150
variable_macro_travel_speed = 600
variable_macro_travel_accel = 8000
variable_macro_z_speed = 15
variable_bed_margin_x = [59.6, 59.6]
variable_bed_margin_y = [14.35, 33.65]
variable_printable_x_min = 0
variable_printable_x_max = 0
variable_printable_y_min = 0
variable_printable_y_max = 0
variable_end_print_motors_off = True
variable_status_color_ok = "00FF00"
variable_status_color_error = "FF0000"
variable_status_color_unknown = "FFFF00"
variable_end_print_retract_filament = 10
gcode = 
	ECHO_RATOS_VARS
variable_auto_center_subject = False
variable_toolchange_zhop = 2.0
variable_toolchange_zspeed = 25
variable_toolchange_sync_fans = False
variable_toolchange_combined_zhop = False
variable_toolchange_travel_speed = 600
variable_toolchange_travel_accel = 8000
variable_toolchange_extrusion = 2.0
variable_toolchange_retraction = 2.0
variable_toolchange_feedrate = 7200
variable_toolchange_prepurging_timer = 0
variable_toolchange_standby_temp = -1
variable_toolchange_purge = 25
variable_toolchange_first_purge = 50
variable_beacon_bed_mesh_scv = 25
variable_beacon_contact_z_homing = False
variable_beacon_contact_start_print_true_zero = True
variable_beacon_contact_start_print_true_zero_fuzzy_position = True
variable_beacon_contact_calibrate_model_on_true_zero = True
variable_beacon_contact_wipe_before_true_zero = True
variable_beacon_contact_wipe_before_true_zero_method = "probe_clean"
variable_beacon_contact_true_zero_temp = 170
variable_beacon_contact_prime_probing = True
variable_beacon_contact_expansion_compensation = True
variable_beacon_contact_bed_mesh = False
variable_beacon_contact_bed_mesh_samples = 2
variable_beacon_contact_z_tilt_adjust = False
variable_beacon_contact_z_tilt_adjust_samples = 2
variable_beacon_scan_compensation_enable = True
variable_beacon_scan_compensation_profile = "auto"
variable_beacon_scan_compensation_desired_spacing = 10
variable_beacon_scan_compensation_bed_temp_mismatch_is_error = False
variable_beacon_contact_poke_bottom_limit = -1
variable_beacon_scan_method_automatic = False
variable_beacon_adaptive_heat_soak = True
variable_beacon_adaptive_heat_soak_max_wait = 5400
variable_beacon_adaptive_heat_soak_extra_wait_after_completion = 0
variable_beacon_adaptive_heat_soak_layer_quality = 3
variable_beacon_adaptive_heat_soak_maximum_first_layer_duration = 1800
variable_beacon_contact_start_print_true_zero_fuzzy_radius = 20
variable_homing_x = "endstop"
variable_homing_y = "endstop"
variable_default_toolhead = 0
variable_adxl_chip = ["lis2dw toolboard_t0", "lis2dw toolboard_t1"]
variable_shaper_x_freq = [0, 0, 0, 0]
variable_shaper_y_freq = [0, 0, 0, 0]
variable_shaper_x_type = ["mzv", "mzv", "mzv", "mzv"]
variable_shaper_y_type = ["mzv", "mzv", "mzv", "mzv"]
variable_x_driver_types = ["tmc5160"]
variable_x_axes = ["x"]
variable_y_driver_types = ["tmc5160", "tmc5160"]
variable_y_axes = ["y", "y1"]
variable_z_driver_types = ["tmc2209", "tmc2209", "tmc2209"]
variable_z_axes = ["z", "z1", "z2"]
variable_home_y_first = True

[ratos_homing]
axes = xyz
z_hop = 15
z_hop_speed = 15
gcode = 
	
	_LED_ON
	
	
	{% set prev_stop_on_error = printer["gcode_macro RatOS"].stowable_probe_stop_on_error %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set target_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	_IDEX_SINGLE
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE=True
	
	
	M400
	
	G90
	
	
	{% set X = true if params.X is defined else false %}
	{% set Y = true if params.Y is defined else false %}
	{% set Z = true if params.Z is defined else false %}
	{% if printer["gcode_macro RatOS"].home_y_first|default(false)|lower == 'true' %}
	HOME_Y X={X} Y={Y} Z={Z}
	HOME_X X={X} Y={Y} Z={Z}
	{% else %}
	HOME_X X={X} Y={Y} Z={Z}
	HOME_Y X={X} Y={Y} Z={Z}
	{% endif %}
	HOME_Z X={X} Y={Y} Z={Z}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE={prev_stop_on_error}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[gcode_macro HOME_X]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_x = printer["gcode_macro RatOS"].homing_x|lower %}
	{% set homing_x = homing_x if homing_x else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_X" MSG="printable_x_max: {printable_x_max}, safe_home_x: {safe_home_x}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}"
	
	
	{% if X or not Y and not Z %}
	{% if homing_x == 'endstop' %}
	G28 X
	{% elif homing_x == 'sensorless' %}
	{% if printer["dual_carriage"] is defined %}
	{ action_emergency_stop("sensorless homing not supported on IDEX!") }
	{% endif %}
	HOME_X_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_x to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_x, homing)) }
	{% endif %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1} MODE=PRIMARY
	G1 X{parking_position} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	{% endif %}
	{% set x_homed = True %}
	G0 X{safe_home_x} F{speed}
	M400
	{% endif %}

[gcode_macro HOME_Y]
gcode = 
	
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_y = printer["gcode_macro RatOS"].homing_y|lower %}
	{% set homing_y = homing_y if homing_y else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Y" MSG="printable_y_max: {printable_y_max}, safe_home_y: {safe_home_y}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}"
	
	
	{% if Y or not X and not Z %}
	{% if homing_y == 'endstop' %}
	G28 Y
	{% elif homing_y == 'sensorless' %}
	HOME_Y_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_y to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_y, homing)) }
	{% endif %}
	{% set y_homed = True %}
	G0 Y{safe_home_y} F{speed}
	{% endif %}

[gcode_macro HOME_Z]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	
	
	{% set beacon_contact_z_homing = true if printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_z_home_position_fuzzing_radius = printer["gcode_macro RatOS"].beacon_z_home_position_fuzzing_radius|default(0)|float %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Z" MSG="x_homed: {x_homed}, y_homed: {y_homed}, z_probe: {z_probe}, beacon_contact_z_homing: {beacon_contact_z_homing}"
	
	
	{% if Z or not Y and not X %}
	RATOS_ECHO MSG="Homing Z"
	{% if x_homed == False or y_homed == False %}
	{ action_emergency_stop("X and Y must be homed before homing Z") }
	{% else %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_homing %}
	{% if beacon_contact_start_print_true_zero %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% else %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	{% else %}
	G28 Z
	{% endif %}
	_Z_HOP
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro HOME_X_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	
	G4 P300
	
	G28 X
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"

[gcode_macro HOME_Y_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	
	G4 P300
	
	G28 Y
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"

[gcode_macro _Z_HOP]
description = Move Z axis up by Z_HOP distance at Z_HOP_SPEED. In relative mode it will move Z axis up by Z_HOP distance. In absolute mode it will move Z axis to Z_HOP distance.
gcode = 
	{% set z_hop = printer.fastconfig.config.ratos_homing.z_hop|float %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	G0 Z{z_hop} F{z_hop_speed}

[gcode_macro __MOVE_TO_SAFE_Z_HOME_ECHO_DEBUG]
gcode = 
	DEBUG_ECHO PREFIX="_MOVE_TO_SAFE_Z_HOME" MSG="x: {params.X}, y: {params.Y}, z_hop: {params.Z_HOP}, fuzzy_radius: {params.FUZZY_RADIUS}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}, printable_x_max: {printer['gcode_macro RatOS'].printable_x_max}, printable_y_max: {printer['gcode_macro RatOS'].printable_y_max}"

[gcode_macro MAYBE_HOME]
description = Only home unhomed axis. Specify ABL=1 to also ensure that automatic bed levelling is applied (if configured).
variable_is_kinematic_position_overriden = False
gcode = 
	{% set abl = params.ABL|default('')|lower in ('true', 'yes', '1') %}
	{% if printer["gcode_macro MAYBE_HOME"].is_kinematic_position_overriden|lower == 'true' %}
	RATOS_ECHO MSG="SET_CENTER_KINEMATIC_POSITION has been abused. Homing all axes. Please refrain from using SET_CENTER_KINEMATIC_POSITION outside of debugging purposes."
	G28
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=False
	{% else %}
	{% set axes = '' %}
	{% set isHomed = true %}
	{% set axesToHome = '' %}
	{% if params.X is defined %}
	{% set axes = axes ~ 'X ' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% endif %}
	{% if params.Y is defined %}
	{% set axes = axes ~ 'Y ' %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% endif %}
	{% if params.Z is defined %}
	{% set axes = axes ~ 'Z ' %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if params.X is not defined and params.Y is not defined and params.Z is not defined %}
	{% set axes = '' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if isHomed is false %}
	RATOS_ECHO MSG="Homing {axesToHome}"
	G28 {axesToHome}
	{% else %}
	RATOS_ECHO MSG="All requested axes already homed. Skipping homing."
	{% endif %}
	{% endif %}
	{% if abl %}
	{% if printer.z_tilt is defined %}
	{% if not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Performing Z tilt adjustment..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Z tilt already applied. Skipping Z tilt adjustment."
	{% endif %}
	{% elif printer.quad_gantry_level is defined %}
	{% if not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Performing quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Quad gantry leveling already applied. Skipping quad gantry leveling."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="No automatic bed leveling method configured. Skipping bed leveling."
	{% endif %}
	{% endif %}

[gcode_macro PID_CALIBRATE_HOTEND]
description = Perform a PID calibration test for a given extruder heater.
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set temp = params.TEMP|default(220)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_HOTEND" MSG="TEMP={temp}"
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO MSG="PID calibration hotend heater T0 at {temp}°C..."
	PID_CALIBRATE HEATER=extruder TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	
	{% if toolhead==0 or toolhead==1 %}
	RATOS_ECHO MSG="PID calibration hotend heater T{toolhead} at {temp}°C..."
	PID_CALIBRATE HEATER=extruder{'' if toolhead==0 else toolhead} TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_BED]
description = Perform a PID calibration test for the bed heater.
gcode = 
	
	{% set temp = params.TEMP|default(80)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_BED" MSG="TEMP={temp}"
	RATOS_ECHO MSG="PID calibration bed heater at {temp}°C..."
	
	
	PID_CALIBRATE HEATER=heater_bed TARGET={temp}
	
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_CHAMBER_HEATER]
description = Perform a PID calibration test for the chamber heater.
gcode = 
	
	{% set temp = params.TEMP|default(150)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_CHAMBER_HEATER" MSG="TEMP={temp}"
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	RATOS_ECHO MSG="PID calibration chamber heater at {temp}°C..."
	PID_CALIBRATE HEATER=chamber_heater TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_heater" %}
	{% set link_text = "RatOS Chamber Heater" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber heater found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro INITIALIZE_PA_TUNING]
description = Start a pressure advance tuning tower.
gcode = 
	
	{% set start = params.START|default(0.0)|float %}
	{% set factor = params.FACTOR|default(0.001)|float %}
	
	
	{% set layer_number = printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|default(0)|int %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if is_printing_gcode and layer_number < 2 %}
	DEBUG_ECHO PREFIX="START_PA_TOWER" MSG="START: {start}, FACTOR: {factor}"
	RATOS_ECHO MSG="Starting pressure advance tuning tower..."
	TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START={start} FACTOR={factor}
	{% else %}
	RATOS_ECHO MSG="Pressure advance tuning tower requires you to be printing gcode and on layer 1 to start."
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro CHAMBER_FILTER_ON]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	_CHAMBER_FILTER_TURN_ON
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro CHAMBER_FILTER_OFF]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Deactivating chamber filter..."
	_CHAMBER_FILTER_TURN_OFF
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set chamber_filter_enable_at = printer["gcode_macro RatOS"].chamber_filter_enable_at|default('after_print_start')|lower %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_ON" MSG="at: {at}, chamber_filter_enable: {chamber_filter_enable}, chamber_filter_enable_at: {chamber_filter_enable_at}, chamber_filter_speed: {chamber_filter_speed}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	{% if chamber_filter_enable_at == at %}
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	
	
	_CHAMBER_FILTER_TURN_ON AT={at}
	
	
	{% if chamber_filter_enable_at == "print_end" %}
	_LED_CHAMBER_FILTER_ON
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_OFF]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF" MSG="chamber_filter_enable: {chamber_filter_enable}, filter_disable_period: {filter_disable_period}, filter_disable_bed_temp: {filter_disable_bed_temp}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	
	{% if filter_disable_period > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting {filter_disable_period} seconds before turning chamber filter off..."
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION={filter_disable_period}
	{% endif %}
	
	
	{% if filter_disable_bed_temp > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting for bed temp to cool down to {filter_disable_bed_temp}°C to turn filter off..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM=0 MAXIMUM={filter_disable_bed_temp}
	_CHAMBER_FILTER_TURN_OFF
	_LED_CHAMBER_FILTER_OFF
	{% endif %}
	
	{% endif %}

[delayed_gcode _CHAMBER_FILTER_OFF_TIMER]
gcode = 
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF_TIMER" MSG="executed"
	
	
	_CHAMBER_FILTER_TURN_OFF
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Chamber filter turned off!"
	
	
	_LED_CHAMBER_FILTER_OFF

[gcode_macro _CHAMBER_FILTER_TURN_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_speed|default(0)|float %}
	{% if at == "print_end" %}
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_disable_speed|default(0)|float %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION=0
	
	
	SET_FAN_SPEED FAN=filter SPEED={chamber_filter_speed}

[gcode_macro _CHAMBER_FILTER_TURN_OFF]
gcode = 
	
	SET_FAN_SPEED FAN=filter SPEED=0

[gcode_macro _CHAMBER_FILTER_SANITY_CHECK]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	{% if filter_disable_bed_temp > 0 and filter_disable_period > 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable, not both.")}
	{% endif %}
	
	{% if filter_disable_bed_temp == 0 and filter_disable_period == 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable.")}
	{% endif %}
	
	{% endif %}

[gcode_macro CHAMBER_HEATER_ON]
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(45)|int %}
	
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp} IS_FROM_START_PRINT=False

[gcode_macro CHAMBER_HEATER_OFF]
gcode = 
	_CHAMBER_HEATER_OFF

[gcode_macro _CHAMBER_HEATER_ON]
variable_chamber_temp = 0
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	{% set is_from_start_print = true if params.IS_FROM_START_PRINT|default(True)|lower == 'true' else false %}
	
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set chamber_heater_enable = true if printer["gcode_macro RatOS"].chamber_heater_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}
	{% set chamber_heater_preheating_temp = printer["gcode_macro RatOS"].chamber_heater_preheating_temp|default(150)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	{% set chamber_heater_control_external_heater = true if printer["gcode_macro RatOS"].chamber_heater_control_external_heater|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_enable = true if printer["gcode_macro RatOS"].chamber_heater_air_circulation_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_fan_speed = printer["gcode_macro RatOS"].chamber_heater_air_circulation_fan_speed|default(0.35)|float %}
	{% set chamber_heater_air_circulation_y_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_y_pos|default(0)|float %}
	{% set chamber_heater_air_circulation_z_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_z_pos|default(100)|float %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_HEATER_ON" MSG="chamber_heater_enable: {chamber_heater_enable}, chamber_heater_preheating_temp: {chamber_heater_preheating_temp}, chamber_heater_heating_temp_offset: {chamber_heater_heating_temp_offset}, bed_temp: {bed_temp}, chamber_temp: {chamber_temp}, start_chamber_temp: {start_chamber_temp}"
	
	
	{% if chamber_heater_enable and chamber_temp > 0 and chamber_heater_bed_temp > 0 %}
	
	
	_LED_HEATING
	
	
	RATOS_ECHO MSG="Preheating chamber to {(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}°C..."
	
	
	{% set chamber_temp_sensor = "extruder" %}
	{% if printer["dual_carriage"] is defined and default_toolhead == 1 %}
	{% set chamber_temp_sensor = "extruder1" %}
	{% endif %}
	{% if printer["temperature_sensor chamber"] is defined %}
	{% set chamber_temp_sensor = "temperature_sensor chamber" %}
	{% endif %}
	
	
	{% set current_chamber_temp = printer['%s' % chamber_temp_sensor].temperature|int %}
	
	
	{% set needs_heating = current_chamber_temp < (start_chamber_temp if start_chamber_temp > 0 else chamber_temp) %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_BEFORE_PREHEATING
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	{% if not is_from_start_print %}
	MAYBE_HOME
	{% endif %}
	G0 Z{chamber_heater_air_circulation_z_pos} F{z_speed}
	G0 Y{chamber_heater_air_circulation_y_pos} F{speed}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * chamber_heater_air_circulation_fan_speed)}
	{% endif %}
	{% else %}
	{% if is_from_start_print %}
	G0 Z{z} F{z_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE={chamber_temp}
	
	
	{% if needs_heating %}
	
	
	M140 S{chamber_heater_bed_temp}
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={chamber_heater_preheating_temp}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	
	{% endif %}
	
	
	{% if needs_heating %}
	_CHAMBER_HEATER_EXTRA_FAN_ON
	{% endif %}
	
	
	{% if needs_heating %}
	TEMPERATURE_WAIT SENSOR="{chamber_temp_sensor}" MINIMUM={(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% endif %}
	
	
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED=0
	_CHAMBER_FILTER_ON AT="before_print_start"
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	G28 Z
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_AFTER_PREHEATING
	{% endif %}
	
	
	{% if printer["temperature_sensor chamber"] is defined %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined and chamber_heater_control_external_heater %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	
	
	_LED_SUCCESS
	
	{% endif %}

[gcode_macro _CHAMBER_HEATER_OFF]
gcode = 
	RATOS_ECHO MSG="Deactivating chamber heater..."
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=0
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE=0
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	
	
	_CHAMBER_HEATER_EXTRA_FAN_OFF

[delayed_gcode _CHAMBER_HEATER_CONTROL]
initial_duration = 0.
gcode = 
	
	{% set chamber_temp = printer["gcode_macro _CHAMBER_HEATER_ON"].chamber_temp|default(0)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	
	
	{% set current_chamber_temp = printer['temperature_sensor chamber'].temperature|int %}
	
	
	{% if current_chamber_temp < chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	{% endif %}
	
	
	{% if current_chamber_temp >= chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_ON]
gcode = 
	
	{% set chamber_heater_extra_fan_speed = printer["gcode_macro RatOS"].chamber_heater_extra_fan_speed|default(0.0)|float %}
	
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	{% if chamber_heater_extra_fan_speed > 0 %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED={chamber_heater_extra_fan_speed}
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_OFF]
gcode = 
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED=0
	{% endif %}

[gcode_macro _USER_CHAMBER_HEATER_BEFORE_PREHEATING]
description = Will be executed before chamber preheating, only if heating is needed.
gcode = 

[gcode_macro _USER_CHAMBER_HEATER_AFTER_PREHEATING]
description = Will be executed after chamber preheating, only if heating was needed.
gcode = 

[gcode_macro RESET_HEATSOAK_SETTINGS]
description = Resets all heatsoak-related settings to startup defaults
gcode = 
	HEATSOAK_SETTINGS ACTION=reset

[gcode_macro USE_ADAPTIVE_HEATSOAK]
description = Temporarily enables adaptive bed heatsoaking (if a beacon probe is present), will reset to printer.cfg settings
	when Klipper is restarted. Optionally specify QUALITY (1-5) and maximum FIRST_LAYER_DURATION (in minutes).
	Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.QUALITY|default("1..5") %}
	{% set _ = params.FIRST_LAYER_DURATION|default("1..120 minutes") %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("Adaptive heatsoaking is only available when a beacon probe is configured.") }
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_quality = (settings.variable_beacon_adaptive_heat_soak_layer_quality if defsrc == 'startup' else current.beacon_adaptive_heat_soak_layer_quality)|default(3)|int %}
	{% set default_first_layer_duration_secs = (settings.variable_beacon_adaptive_heat_soak_maximum_first_layer_duration if defsrc == 'startup' else current.beacon_adaptive_heat_soak_maximum_first_layer_duration)|default(1800)|int %}
	{% if params2.QUALITY is defined %}
	{% set quality = params2.QUALITY|int %}
	{% if quality < 1 or quality > 5 %}
	{ action_raise_error("QUALITY must be between 1 (rough) and 5 (maximum). Use 3 (normal) if unsure.") }
	{% endif %}
	{% else %}
	{% set quality = default_quality %}
	{% endif %}
	{% if params2.FIRST_LAYER_DURATION is defined %}
	{% set first_layer_duration_mins = params2.FIRST_LAYER_DURATION|float %}
	{% if first_layer_duration_mins <= 0 %}
	{ action_raise_error("FIRST_LAYER_DURATION must be a positive number specifying the maximum first layer duration in minutes.") }
	{% endif %}
	{% if first_layer_duration_mins > 120 %}
	CONSOLE_ECHO MSG="FIRST_LAYER_DURATION will be limited to 120 minutes. Values larger than this will not have an effect on soak time."
	{% set first_layer_duration_mins = 120 %}
	{% endif %}
	{% set first_layer_duration_secs = (first_layer_duration_mins * 60.0)|int %}
	{% else %}
	{% set first_layer_duration_secs = default_first_layer_duration_secs %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	{% endif %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=True beacon_adaptive_heat_soak_layer_quality={quality} beacon_adaptive_heat_soak_maximum_first_layer_duration={first_layer_duration_secs}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."

[gcode_macro USE_FIXED_HEATSOAK]
description = Temporarily enables fixed bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
	Optionally specify DURATION (in minutes). Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.DURATION|default("0..720 minutes") %}
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_duration = (settings.variable_bed_heat_soak_time if defsrc == 'startup' else current.bed_heat_soak_time)|default(0)|int %}
	{% if params2.DURATION is defined %}
	{% set duration_mins = params2.DURATION|float %}
	{% if duration_mins < 0 %}
	{ action_raise_error("DURATION must be a non-negative number specifying the heatsoak duration in minutes.") }
	{% endif %}
	{% if duration_mins > 720 %}
	CONSOLE_ECHO MSG="DURATION will be limited to 720 minutes (12 hours). If you really need a larger value, adjust printer.cfg instead."
	{% set duration_mins = 720 %}
	{% endif %}
	{% set duration_secs = (duration_mins * 60.0)|int %}
	{% else %}
	{% set duration_secs = default_duration %}
	{% set duration_mins = duration_secs / 60.0 %}
	{% endif %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% if has_beacon %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=False bed_heat_soak_time={duration_secs}
	{% else %}
	HEATSOAK_SETTINGS QUIET=1 bed_heat_soak_time={duration_secs}
	{% endif %}
	{% if duration_mins < 1e-3 %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% else %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% endif %}

[gcode_macro USE_NO_HEATSOAK]
description = Temporarily disables bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
gcode = 
	USE_FIXED_HEATSOAK DURATION=0

[gcode_macro HEATSOAK_SETTINGS]
description = Shows or adjusts heatsoak settings
	- With no arguments: shows current heatsoak settings, specify VERBOSE=1 for detailed output
	- With arguments: sets the specified settings. Use the full setting name without the variable_ prefix, e.g. bed_heat_soak_time=300 or beacon_adaptive_heat_soak_layer_quality=4. See printer.cfg for available settings.
variable_default_source = "startup"
gcode = 
	
	{% set params2 = params %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% set quiet = params2.pop("QUIET", None)|default("0") in ("1", "true", "yes") %}
	{% set verbose = params2.pop("VERBOSE", None)|default("0") in ("1", "true", "yes") %}
	{% if has_beacon %}
	{% set vars = (
	"beacon_adaptive_heat_soak",
	"beacon_adaptive_heat_soak_max_wait",
	"beacon_adaptive_heat_soak_extra_wait_after_completion",
	"beacon_adaptive_heat_soak_layer_quality",
	"beacon_adaptive_heat_soak_maximum_first_layer_duration",
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% else %}
	{% set vars = (
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% endif %}
	{% set action = "show" if params|length == 0 else params2.ACTION %}
	{% if action is defined and params|length > 1 %}
	{ action_raise_error("ACTION cannot be specified with other parameters.") }
	{% elif action is not defined %}
	{% for k, v in params2.items() %}
	{% set k = k|lower %}
	{% if k in vars %}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Setting {k} to {v}"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={k} VALUE={v}
	{% else %}
	{ action_raise_error("Parameter '%s' is not recognised. Note that adaptive heatsoaking settings can only be set when a beacon probe is configured." % k) }
	{% endif %}
	{% endfor %}
	{% elif action == "reset" %}
	_RESET_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	CONSOLE_ECHO MSG="Heatsoak settings have been reset to their original values."
	{% elif action == "show" %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% set is_adaptive = False if not has_beacon else current.beacon_adaptive_heat_soak|default("")|lower == "true" %}
	{% if is_adaptive %}
	{% set quality = current.beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set first_layer_duration_secs = current.beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."
	{% elif current.bed_heat_soak_time|default(0)|int > 0 %}
	{% set duration_mins = (current.bed_heat_soak_time|int / 60.0) %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% else %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% endif %}
	{% if verbose %}
	CONSOLE_ECHO MSG="Detailed settings:"
	_SHOW_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	{% endif %}
	{% else %}
	{ action_raise_error("Action '%s' is not recognised" % action) }
	{% endif %}

[gcode_macro _LED_START_PRINTING]
gcode = 
	_LED_ACTION

[gcode_macro _LED_START_PRINTING_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_PRINTING]
gcode = 
	_LED_ON TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_PAUSE]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_ON]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_OFF]
gcode = 
	_LED_STANDBY

[gcode_macro _LED_LOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_LOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_RUNOUT]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_CLOG]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_UNLOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_UNLOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_DEACTIVATE_TOOLHEAD]
gcode = 
	_LED_OFF TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_STANDBY]
gcode = 
	_LED_STANDBY TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_WAKEUP]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_MOTORS_OFF]
gcode = 
	_LED_STANDBY
	_LED_VAOC_OFF

[gcode_macro _LED_INPUT_SHAPER_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_INPUT_SHAPER_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_BEACON_CALIBRATION_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_VAOC_ON]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=1.0 GREEN=1.0 BLUE=1.0
	{% endif %}

[gcode_macro _LED_VAOC_OFF]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=0.0 GREEN=0.0 BLUE=0.0
	{% endif %}

[gcode_macro _LED_ACTION]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_action %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SUCCESS]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_success %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_HEATING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_heating %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_COOLING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_cooling %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ERROR]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_error %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ON]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_on %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_OFF]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_off %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_STANDBY]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_standby %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}
	
	{% if toolhead >= 0 %}
	{% if printer['neopixel nozzle_led_t%s' % toolhead] is defined  %}
	SET_LED LED={'nozzle_led_t%s' % toolhead} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% else %}
	{% if printer['neopixel nozzle_led_t0'] is defined  %}
	SET_LED LED={'nozzle_led_t0'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% if printer['neopixel nozzle_led_t1'] is defined %}
	SET_LED LED={'nozzle_led_t1'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% endif %}
	
	_USER_LED_SET { rawparams }

[gcode_macro _USER_LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}

[gcode_macro LOAD_FILAMENT]
description = Loads new filament. Note: be careful with PETG, make sure you inspect the tip of your filament before loading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% if filament_name == '' or filament_type == '' %}
	{% set filament_name = 'unknown' %}
	{% set filament_type = 'unknown' %}
	{% endif %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_LOAD_FILAMENT TEMP={temp} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_LOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_LOAD_FILAMENT]
description = Load filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_LOAD_FILAMENT" MSG="TEMP={temp}"
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=load_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	_LOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	
	
	RESTORE_GCODE_STATE NAME=load_state
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament load routine complete, please check that the filament was loaded correctly."

[gcode_macro _IDEX_LOAD_FILAMENT]
description = Load filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament into T{toolhead}..."
	
	DEBUG_ECHO PREFIX="_IDEX_LOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	_LOAD_FILAMENT TOOLHEAD={toolhead} TEMP={temp} AUTOMATED={automated}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="Filament load routine for T{toolhead} complete, please check that the filament was loaded correctly."

[gcode_macro _LOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default(false)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE TOOLHEAD={toolhead}
	_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into hotend.."
	G92 E0
	G0 E{extruder_gear_to_cooling_position_distance} F{extruder_load_speed}
	G92 E0
	M400
	RATOS_ECHO MSG="Filament loaded into hotend."

[gcode_macro _LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set load_speed = printer["gcode_macro T%s" % toolhead].filament_load_speed|float * 60 %}
	{% set filament_loading_nozzle_offset = printer["gcode_macro T%s" % toolhead].filament_loading_nozzle_offset|float %}
	{% set cooling_position_to_nozzle_distance = printer["gcode_macro T%s" % toolhead].cooling_position_to_nozzle_distance|float %}
	{% set purge_after_load = printer["gcode_macro T%s" % toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into nozzle... Please wait!"
	G92 E0
	
	G0 E{cooling_position_to_nozzle_distance + filament_loading_nozzle_offset} F{load_speed}
	G92 E0
	G4 P1000
	_PURGE_FILAMENT	TOOLHEAD={toolhead} E={purge_after_load}
	RATOS_ECHO MSG="Filament loaded into nozzle!"

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"
	
	
	{% set filament_grabbing_length = printer["gcode_macro T%s" % toolhead].filament_grabbing_length|float %}
	{% set filament_grabbing_speed = printer["gcode_macro T%s" % toolhead].filament_grabbing_speed|float %}
	{% set resume_after_insert = true if printer["gcode_macro T%s" % toolhead].resume_after_insert|default(true)|lower == 'true' else false %}
	{% set enable_insert_detection = true if printer["gcode_macro T%s" % toolhead].enable_insert_detection|default(true)|lower == 'true' else false %}
	
	
	{% set current_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	
	{% if enable_insert_detection %}
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="toolhead: {toolhead}, filament_grabbing_length: {filament_grabbing_length}, filament_grabbing_speed: {filament_grabbing_speed}, current_idex_mode: {current_idex_mode}"
	
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	RATOS_ECHO MSG="Filament inserted into T{toolhead}, loading..."
	
	
	FORCE_MOVE STEPPER={'extruder%s' % ('' if toolhead == 0 else toolhead)} DISTANCE={filament_grabbing_length} VELOCITY={filament_grabbing_speed}
	M400
	
	
	{% if printer.pause_resume.is_paused %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% if resume_after_insert %}
	RESUME
	{% endif %}
	{% else %}
	{% if not printer.virtual_sdcard.is_active %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"

[gcode_macro _PURGE_BEFORE_UNLOAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set purge_before_unload = printer["gcode_macro T%s" % toolhead].purge_before_unload|float %}
	
	DEBUG_ECHO PREFIX="_PURGE_BEFORE_UNLOAD" MSG="TOOLHEAD: {toolhead}"
	
	
	{% if purge_before_unload > 0 %}
	G92 E0
	G0 E{purge_before_unload} F300
	G92 E0
	M400
	{% endif %}

[gcode_macro _PURGE_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set e = params.E|int %}
	{% set r = params.R|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_PURGE_FILAMENT" MSG="TOOLHEAD: {toolhead}, E: {e}"
	
	
	{% if e > 0 %}
	
	
	G92 E0
	G0 E{e} F300
	G92 E0
	M400
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={0.4 if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={0.4 if toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * 0.4)}
	{% endif %}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if r > 0 %}
	G92 E0
	G0 E-{r} F300
	G92 E0
	M400
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro _MOVE_TO_LOADING_POSITION]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_MOVE_TO_LOADING_POSITION" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	
	G1 X{loading_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _CLEANING_MOVE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_CLEANING_MOVE" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].parking_position is defined and printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set parking_position = printer["gcode_macro T%s" % toolhead].parking_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	{% set cleaning_position = loading_position %}
	{% if loading_position == parking_position %}
	{% if loading_position > 0 %}
	{% set cleaning_position = loading_position - 30 %}
	{% else %}
	{% set cleaning_position = loading_position + 30 %}
	{% endif %}
	{% endif %}
	
	
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _BED_MESH_SANITY_CHECK]
gcode = 
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is defined %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_start_print_true_zero_fuzzy_position %}
	CONSOLE_ECHO TYPE="error" TITLE="Defined zero reference not compatible with fuzzy true zero" MSG="Using fuzzy start print true zero position is not compatible with a defined zero_reference_position value in the [bed_mesh] section in printer.cfg._N_Please remove the zero_reference_position value from the [bed_mesh] section, or disable fuzzy true zero position in printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_start_print_true_zero_fuzzy_position: False"
	_STOP_AND_RAISE_ERROR MSG="Defined zero reference not compatible with fuzzy true zero"
	{% elif zero_ref_pos[0]|float|round != safe_home_x|float|round or zero_ref_pos[1]|float|round != safe_home_y|float|round %}
	CONSOLE_ECHO TYPE="error" TITLE="Zero reference position does not match safe home position" MSG="Please update your bed mesh zero reference position in printer.cfg, like so:_N__N_[bed_mesh]_N_zero_reference_position: {safe_home_x|float|round},{safe_home_y|float|round}_N_"
	_STOP_AND_RAISE_ERROR MSG="Zero reference position does not match safe home position"
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_bed_mesh %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact bed mesh is enabled" MSG="Beacon contact bed mesh is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_bed_mesh: False"
	{% endif %}
	
	{% if beacon_scan_method_automatic %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon 'automatic' scan method is enabled" MSG="Beacon 'automatic' scan method is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_scan_method_automatic: False"
	{% endif %}
	
	{% if beacon_contact_z_tilt_adjust %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact z-tilt adjust is enabled" MSG="Beacon contact z-tilt adjust is enabled. This is not recommended for normal use and may result in inaccurate z-tilt adjustment._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_z_tilt_adjust: False"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH]
gcode = 
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE=None
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE=None
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION {rawparams}
	{% endif %}

[gcode_macro _START_PRINT_BED_MESH]
variable_actual_true_zero_position_x = None
variable_actual_true_zero_position_y = None
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set X=[params.X0|default(-1)|float, params.X1|default(-1)|float] %}
	{% set Y=[params.Y0|default(-1)|float, params.Y1|default(-1)|float] %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_BED_MESH" MSG="idex_mode: {idex_mode}, X: {X}, Y: {Y}"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is not defined %}
	{% set zero_ref_pos = [safe_home_x if actual_true_zero_position_x is none else actual_true_zero_position_x, safe_home_y if actual_true_zero_position_y is none else actual_true_zero_position_y] %}
	{% endif %}
	
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	
	
	
	
	{% set X=[0, printable_x_max] %}
	{% endif %}
	
	
	{% set beacon_bed_mesh_scv = printer["gcode_macro RatOS"].beacon_bed_mesh_scv|default(25)|int %}
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% if printer.fastconfig.settings.beacon is defined and not beacon_contact_bed_mesh %}
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={beacon_bed_mesh_scv}
	{% endif %}
	
	
	{% set default_profile = printer["gcode_macro RatOS"].bed_mesh_profile|default('ratos') %}
	{% if printer["gcode_macro RatOS"].calibrate_bed_mesh|lower == 'true' %}
	BED_MESH_CLEAR
	{% if printer["gcode_macro RatOS"].adaptive_mesh|lower == 'true' %}
	CALIBRATE_ADAPTIVE_MESH PROFILE="{default_profile}" X0={X[0]} X1={X[1]} Y0={Y[0]} Y1={Y[1]} T={params.T|int} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={idex_mode} ZERO_REF_POS_X={zero_ref_pos[0]} ZERO_REF_POS_Y={zero_ref_pos[1]}
	{% else %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	BED_MESH_PROFILE LOAD="{default_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	
	{% elif printer["gcode_macro RatOS"].bed_mesh_profile is defined %}
	BED_MESH_CLEAR
	BED_MESH_PROFILE LOAD="{printer["gcode_macro RatOS"].bed_mesh_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"

[gcode_macro CALIBRATE_ADAPTIVE_MESH]
gcode = 
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set default_profile = params.PROFILE %}
	
	
	{% set x0 = params.X0|default(-1)|float %}
	{% set y0 = params.Y0|default(-1)|float %}
	{% set x1 = params.X1|default(-1)|float %}
	{% set y1 = params.Y1|default(-1)|float %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Received coordinates X0={x0|round(1)} Y0={y0|round(1)} X1={x1|round(1)} Y1={y1|round(1)}"
	
	{% if x0 >= x1 or y0 >= y1 %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Invalid coordinates received. Please check your slicer settings. Falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	
	
	{% if params.ZERO_REF_POS_X is defined and params.ZERO_REF_POS_Y is defined %}
	{% set zero_ref_pos_x = params.ZERO_REF_POS_X|float %}
	{% set zero_ref_pos_y = params.ZERO_REF_POS_Y|float %}
	{% if zero_ref_pos_x < x0 or zero_ref_pos_x > x1 or zero_ref_pos_y < y0 or zero_ref_pos_y > y1 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Zero reference position X={zero_ref_pos_x|round(1)} Y={zero_ref_pos_y|round(1)} is outside the mesh region, expanding mesh region to include it."
	{% set x0 = [x0, zero_ref_pos_x]|min %}
	{% set y0 = [y0, zero_ref_pos_y]|min %}
	{% set x1 = [x1, zero_ref_pos_x]|max %}
	{% set y1 = [y1, zero_ref_pos_y]|max %}
	{% endif %}
	{% endif %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float %}
	
	
	{% set mesh_x0 = [[x0, max_x]|min, min_x]|max %}
	{% set mesh_y0 = [[y0, max_y]|min, min_y]|max %}
	{% set mesh_x1 = [[x1, max_x]|min, min_x]|max %}
	{% set mesh_y1 = [[y1, max_y]|min, min_y]|max %}
	
	{% if mesh_x0 == min_x and mesh_y0 == min_y and mesh_x1 == max_x and mesh_y1 == max_y %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Print is using the full bed, falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	
	{% set probe_count_x = mesh_config.probe_count.split(",")[0]|int %}
	{% if mesh_config.probe_count.split(",")|length == 2 %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[1]|int %}
	{% else %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[0]|int %}
	{% endif %}
	
	
	{% set probe_x_step = (max_x - min_x) / probe_count_x %}
	{% set probe_y_step = (max_y - min_y) / probe_count_y %}
	
	
	{% set mesh_count_x = ([(mesh_x1 - mesh_x0) / probe_x_step, 3]|max)|int %}
	{% set mesh_count_y = ([(mesh_y1 - mesh_y0) / probe_y_step, 3]|max)|int %}
	{% set min_mesh_count = [mesh_count_x, mesh_count_y]|min %}
	{% set max_mesh_count = [mesh_count_x, mesh_count_y]|max %}
	
	
	{% set algorithm = mesh_config.algorithm %}
	{% if algorithm|lower == 'lagrange' and max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="cannot exceed a probe_count of 6 when using lagrange interpolation. Falling back to bicubic interpolation."
	{% set algorithm = 'bicubic' %}
	{% endif %}
	{% if algorithm|lower == 'bicubic' and min_mesh_count < 4 %}
	{% if max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="invalid probe_count option when using bicubic interpolation. Combination of 3 points on one axis with more than 6 on another is not permitted. Forcing minimum mesh count to be 4."
	{% set min_mesh_count = 4 %}
	{% else %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="bicubic interpolation with a probe_count of less than 4 points detected. Forcing lagrange interpolation."
	{% set algorithm = 'lagrange' %}
	{% endif %}
	{% endif %}
	
	{% set mesh_count_x = ([min_mesh_count, mesh_count_x]|max)|int %}
	{% set mesh_count_x = ([max_mesh_count, mesh_count_x]|min)|int %}
	{% set mesh_count_y = ([min_mesh_count, mesh_count_y]|max)|int %}
	{% set mesh_count_y = ([max_mesh_count, mesh_count_y]|min)|int %}
	
	{% set should_prime = printer["gcode_macro RatOS"].nozzle_priming == 'primeblob' %}
	{% if printer["dual_carriage"] is not defined %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% else %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 != 0 and probe_first %}
	{% set probe_first = false %}
	{% elif printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 == 0 and not probe_first %}
	{% set probe_first = true %}
	{% endif %}
	
	
	{% if should_prime and probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="mesh coordinates X0={mesh_x0|round(1)} Y0={mesh_y0|round(1)} X1={mesh_x1|round(1)} Y1={mesh_y1|round(1)}"
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y} RELATIVE_REFERENCE_INDEX=-1
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	
	
	{% if should_prime and not probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro M84]
rename_existing = M84.1
gcode = 
	
	M84.1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_OFFSET X=0 Y=0
	
	
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro _VAOC"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False
	{% endif %}
	
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	SET_SKEW CLEAR=1
	
	
	_LED_MOTORS_OFF

[gcode_macro M104]
rename_existing = M104.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M104" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set temperature_offset_t0 = printer["gcode_macro T0"].temperature_offset|default(0)|int %}
	{% set temperature_offset_t1 = printer["gcode_macro T1"].temperature_offset|default(0)|int %}
	{% set s0 = [s + temperature_offset_t0, 0]|max %}
	{% set s1 = [s + temperature_offset_t1, 0]|max %}
	{% if temperature_offset_t0 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t0}°C added to toolhead T0."
	{% endif %}
	{% if temperature_offset_t1 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t1}°C added to toolhead T1."
	{% endif %}
	{% else %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	M104.1 S{s0} T0
	M104.1 S{s1} T1
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% else %}
	M104.1 S{s} T{t}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M109]
rename_existing = M109.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M109" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M109" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	M109.1 S{s} T{t}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro SET_HEATER_TEMPERATURE]
rename_existing = SET_HEATER_TEMPERATURE_BASE
gcode = 
	
	{% set heater = params.HEATER|default("") %}
	{% set target = params.TARGET|default(0)|int %}
	
	DEBUG_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="heater: {heater}, target: {target}"
	
	{% set t = -1 %}
	{% if heater|lower == "extruder" or heater|lower == "extruder1" %}
	
	{% set t = 0 if heater|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and target > 0 %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set target = [target + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE_BASE HEATER="{heater}" TARGET={target}
	
	{% if t != -1 and printer.fastconfig.settings.beacon is defined %}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro TEMPERATURE_WAIT]
rename_existing = TEMPERATURE_WAIT_BASE
gcode = 
	
	{% set sensor = params.SENSOR|default("") %}
	{% set minimum = params.MINIMUM|default(-1)|int %}
	{% set maximum = params.MAXIMUM|default(-1)|int %}
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="sensor: {sensor}, minimum: {minimum}, maximum: {maximum}"
	
	{% set t = -1 %}
	{% if sensor|lower == "extruder" or sensor|lower == "extruder1" %}
	
	{% set t = 0 if sensor|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and (minimum > 0 or maximum > 0) %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% if minimum > -1 %}
	{% set minimum = [minimum + temperature_offset, 0]|max %}
	{% endif %}
	{% if maximum > -1 %}
	{% set maximum = [maximum + temperature_offset, 0]|max %}
	{% endif %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set id = "sensor " ~ sensor if t == -1 else "toolhead T" ~ t %}
	
	
	{% if minimum > -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum} MAXIMUM={maximum}
	{% elif minimum > -1 and maximum == -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum}
	{% elif minimum == -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MAXIMUM={maximum}
	{% else %}
	
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="neither MINIMUM or MAXIMUM args were specified, call TEMPERATURE_WAIT_BASE is expected to fail"
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}"
	{% endif %}
	
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature for {id} reached."

[gcode_macro SDCARD_PRINT_FILE]
rename_existing = SDCARD_PRINT_FILE_BASE
gcode = 
	{% if printer["ratos"] is defined %}
	PROCESS_GCODE_FILE { rawparams }
	{% else %}
	SDCARD_PRINT_FILE_BASE { rawparams }
	{% endif %}

[gcode_macro SKEW_PROFILE]
rename_existing = SKEW_PROFILE_BASE
variable_loaded_profile = ""
gcode = 
	{% if params.LOAD is defined %}
	{% if printer.fastconfig.settings["skew_correction %s" % params.LOAD] is defined %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='"{params.LOAD}"'
	{% endif %}
	{% endif %}
	
	SKEW_PROFILE_BASE { rawparams }

[gcode_macro SET_SKEW]
rename_existing = SET_SKEW_BASE
gcode = 
	{% if params.CLEAR is defined %}
	{% if params.CLEAR|default(0)|int == 1 %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='""'
	{% endif %}
	{% endif %}
	
	SET_SKEW_BASE { rawparams }

[gcode_macro SET_VELOCITY_LIMIT]
rename_existing = SET_VELOCITY_LIMIT_BASE
gcode = 
	{% if params.ACCEL_TO_DECEL is defined %}
	
	{% if params.ACCEL is defined %}
	{% set accel = params.ACCEL|float %}
	{% else %}
	{% set accel = printer.toolhead.max_accel|float %}
	{% endif %}
	
	{% if params.VELOCITY is defined %}
	{% set velocity = params.VELOCITY|float %}
	{% else %}
	{% set velocity = printer.toolhead.max_velocity|float %}
	{% endif %}
	
	{% if params.SQUARE_CORNER_VELOCITY is defined %}
	{% set scv = params.SQUARE_CORNER_VELOCITY|float %}
	{% else %}
	{% set scv = printer.toolhead.square_corner_velocity|float %}
	{% endif %}
	
	{% set mcr = params.ACCEL_TO_DECEL|float / accel %}
	
	DEBUG_ECHO PREFIX="SET_VELOCITY_LIMIT" MSG="ACCEL={accel}, VELOCITY={velocity}, SQUARE_CORNER_VELOCITY={scv}, MINIMUM_CRUISE_RATIO={mcr}"
	
	SET_VELOCITY_LIMIT_BASE ACCEL={accel} VELOCITY={velocity} SQUARE_CORNER_VELOCITY={scv} MINIMUM_CRUISE_RATIO={1-mcr}
	
	{% else %}
	
	SET_VELOCITY_LIMIT_BASE { rawparams }
	
	{% endif %}

[gcode_macro BED_MESH_CALIBRATE]
rename_existing = _BED_MESH_CALIBRATE_BASE
variable_abl_and_home_z_if_required = True
gcode = 
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	{% if abl_and_home_z_if_required %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% endif %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set beacon_default_probe_method = printer.fastconfig.settings.beacon.default_probe_method|default('proximity') %}
	{% set probe_method = params.PROBE_METHOD|default(beacon_default_probe_method)|lower %}
	{% if probe_method == 'proximity' %}
	_CHECK_ACTIVE_BEACON_MODEL_TEMP TITLE="Bed mesh calibration warning"
	{% endif %}
	{% endif %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_BED_MESH_CALIBRATE_BASE {rawparams}
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	_APPLY_RATOS_BED_MESH_PARAMETERS {rawparams}
	{% endif %}

[gcode_macro SET_GCODE_OFFSET]
rename_existing = SET_GCODE_OFFSET_BASE
gcode = 
	DEBUG_ECHO PREFIX="SET_GCODE_OFFSET" MSG="{rawparams|replace('"', '')|replace("'", '')}"
	{% set z_before = printer.gcode_move.homing_origin.z|float %}
	SET_GCODE_OFFSET_BASE {rawparams}
	_AFTER_SET_GCODE_OFFSET Z_BEFORE={z_before}

[gcode_macro _AFTER_SET_GCODE_OFFSET]
gcode = 
	{% set z_before = params.Z_BEFORE|float %}
	{% set z_after = printer.gcode_move.homing_origin.z|float %}
	{% if z_before != z_after %}
	_ALERT_NON_ZERO_Z_OFFSET FORCE=1
	{% endif %}

[gcode_macro _START_PRINT_PARK]
gcode = 
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_x = printer["gcode_macro RatOS"].start_print_park_x %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% if printer["gcode_macro RatOS"].start_print_park_x is defined and printer["gcode_macro RatOS"].start_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="start_print_park_x is ignored for IDEX printers"
	{% endif %}
	PARK_TOOLHEAD
	G90
	{% endif %}
	
	
	_PARK LOCATION={start_print_park_in} X={start_print_park_x}
	G0 Z{z} F{z_speed}

[gcode_macro _END_PRINT_PARK]
gcode = 
	{% if printer["dual_carriage"] is defined %}
	
	{% if printer["gcode_macro RatOS"].end_print_park_x is defined and printer["gcode_macro RatOS"].end_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="end_print_park_x is ignored for IDEX printers"
	{% endif %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	PARK_TOOLHEAD
	G90
	{% endif %}
	_PARK LOCATION={printer["gcode_macro RatOS"].end_print_park_in} X={printer["gcode_macro RatOS"].end_print_park_x}

[gcode_macro _PARK]
gcode = 
	
	{% set x = params.X %}
	{% set location = params.LOCATION|default('back')|lower %}
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	{% set nozzle_priming = printer["gcode_macro RatOS"].nozzle_priming|lower %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="park"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% if x != '' %}
	{% if x|float >= printer.toolhead.axis_minimum.x + 5 and x|float <= printable_x_max - 5 %}
	{% set park_x = x|float %}
	{% else %}
	{action_respond_info('The requested X co-ordinate is outside the defined axis bounds - using defaults')}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	{% else %}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	
	
	{% set park_y = printable_y_max - 15 %}
	{% if location == 'front' %}
	{% set park_y = printer.toolhead.axis_minimum.y + 5 %}
	{% elif location == 'center' %}
	{% set park_y = printable_y_max / 2 %}
	{% elif location == 'primeblob' and printer["dual_carriage"] is defined %}
	
	{% set park_y = printable_y_max - 15 %}
	{% endif %}
	
	
	{% if location == 'primeblob' and printer["dual_carriage"] is not defined %}
	{% if (nozzle_priming == 'primeblob' or nozzle_priming == 'primeline') %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set park_x = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set park_x = printable_x_max - 5 %}
	{% else %}
	{% set park_x = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set park_y = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set park_y = printable_y_max - 5 %}
	{% else %}
	{% set park_y = nozzle_prime_start_y|float %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	G0 X{park_x} Y{park_y} F{speed}
	{% else %}
	
	G0 Y{park_y} F{speed}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="park"

[gcode_macro SAVE_PROBE_RESULT]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	{% set last_z_offset = 9999.9 %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if beacon_contact_prime_probing %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	{% else %}
	{% set last_z_offset = printer.beacon.last_sample.dist - current_z %}
	{% endif %}
	{% elif printer.fastconfig.settings.bltouch is defined  %}
	{% set config_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% elif printer.fastconfig.settings.probe is defined  %}
	{% set config_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% endif %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Saving offset adjustment of {last_z_offset} in {params.VARIABLE|default('last_z_offset')}"
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={params.VARIABLE|default('last_z_offset')} VALUE={last_z_offset}

[gcode_macro PROBE_FOR_PRIMING]
gcode = 
	
	{% set probe_for_priming_disable_mesh_constraints = true if printer["gcode_macro RatOS"].probe_for_priming_disable_mesh_constraints|default(false)|lower == 'true' else false %}
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower != 'false' %}
	SAVE_GCODE_STATE NAME=probe_for_priming_state
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the prime location.."
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set t = params.TOOLHEAD|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% if idex_mode == '' %}
	
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% if t == 0 %}
	{% set x_start = 5 %}
	{% else %}
	{% set x_start = printable_x_max - 5 %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% endif %}
	{% endif %}
	{% set z = printer.fastconfig.settings.bed_mesh.horizontal_move_z|float %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% if printer.fastconfig.settings.bltouch is defined %}
	{% set x_offset = printer.fastconfig.settings.bltouch.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.bltouch.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% elif printer.fastconfig.settings.probe is defined %}
	{% set x_offset = printer.fastconfig.settings.probe.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.probe.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% elif printer.fastconfig.settings.beacon is defined %}
	{% set x_offset = printer.fastconfig.settings.beacon.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.beacon.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.beacon.trigger_distance|float %}
	{% else %}
	{ action_raise_error("No probe, beacon or bltouch section found. Adaptive priming only works with a [probe], [beacon] or [bltouch] section defined.") }
	{% endif %}
	
	{% if z < z_offset %}
	{ action_raise_error("Horizontal move Z ({z}) is below your probe's Z offset ({z_offset}). Please adjust your horizontal_move_z setting in [bed_mesh] to be above {z}.") }
	{% endif %}
	
	{% if not probe_for_priming_disable_mesh_constraints %}
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float - x_offset %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float - y_offset %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float - x_offset %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float - y_offset %}
	
	
	{% set x_start = [[x_start, max_x]|min, min_x]|max %}
	{% set y_start = [[y_start, max_y]|min, min_y]|max %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the start of the prime location at {x_start}, {y_start}"
	
	G90
	
	M83
	
	G0 Z{z} F{z_speed}
	
	G1 X{x_start} Y{y_start} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result
	{% endif %}
	
	{% if idex_mode == '' %}
	
	{% set x_end = x_start %}
	{% set y_end = y_start + 45 %}
	{% else %}
	
	{% if t==1 %}
	{% set x_end = x_start - 45 %}
	{% else %}
	{% set x_end = x_start + 45 %}
	{% endif %}
	{% set y_end = y_start %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the end of the prime location at {x_end}, {y_end}"
	G1 X{x_end} Y{y_end} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result
	{% endif %}
	
	RESTORE_GCODE_STATE NAME=probe_for_priming_state
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	{% endif %}

[gcode_macro RESET_PRIME_PROBE_STATE]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result VALUE=None
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result_t1 VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result_t1 VALUE=None
	{% endif %}

[gcode_macro PROBE_CURRENT_POSITION]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	SAVE_GCODE_STATE NAME=probe_current_position_state
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	ASSERT_PROBE_DEPLOYED
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_prime_probing %}
	PROBE PROBE_METHOD=contact SAMPLES=1
	{% else %}
	PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	BEACON_QUERY
	{% else %}
	
	RESTORE_GCODE_STATE NAME=probe_current_position_state MOVE=1 MOVE_SPEED={printer["gcode_macro RatOS"].macro_z_speed|float}
	{% endif %}

[gcode_macro PRIME_BLOB]
description = Prints a primeblob, used internally, if configured, as part of the START_PRINT macro.
variable_x_offset = 5
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="prime_blob"
	SET_MACRO_TRAVEL_SETTINGS
	
	RATOS_ECHO PREFIX="Priming" MSG="Priming nozzle with prime blob.."
	
	
	{% set current_toolhead = 0 %}
	
	
	{% set target_idex_mode = '' %}
	{% set extruder = 'extruder' %}
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE is defined %}
	{% set target_idex_mode = params.IDEX_MODE|default('')|lower %}
	{% else %}
	{ action_raise_error("IDEX_MODE parameter not found for PRIME_BLOB macro. This is likely a bug.") }
	{% endif %}
	RATOS_ECHO PREFIX="Priming" MSG="Priming in IDEX {target_idex_mode} mode.."
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set current_toolhead = 1 if current_idex_mode=='primary' else 0 %}
	{% set extruder = 'extruder1' if current_toolhead == 1 else 'extruder' %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	SAVE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set fan_speed = printer["gcode_macro RatOS"].nozzle_prime_bridge_fan|float %}
	{% set nozzle_diameter = printer.fastconfig.settings[extruder].nozzle_diameter|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set has_start_offset_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) != 9999.9 %}
	{% if printer["dual_carriage"] is defined %}
	{% set has_start_offset_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) != 9999.9 %}
	{% endif %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_z_height = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set nozzle_prime_direction = printer["gcode_macro RatOS"].nozzle_prime_direction|lower %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% if target_idex_mode == '' %}
	
	{% set x_factor = 0 %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% set y_factor = -1 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% if nozzle_prime_start_y|float < printable_y_max / 2 %}
	{% set y_factor = 1 %}
	{% else %}
	{% set y_factor = -1 %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_direction == 'forwards' %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_direction == 'backwards' %}
	{% set y_factor = -1 %}
	{% endif %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% else %}
	{% set z = start_print_park_z_height %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% set y_factor = 0 %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set x_start = center_x / 2 + 5 %}
	{% set x_factor = 1 %}
	{% else %}
	
	
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% if current_toolhead == 0 %}
	{% set x_start = 55 %}
	{% set x_factor = -1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 55 %}
	{% set x_factor = 1 %}
	{% endif %}
	{% else %}
	{% if current_toolhead == 0 %}
	{% set x_start = 5 %}
	{% set x_factor = 1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 5 %}
	{% set x_factor = -1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_x_max - 5 %}
	{% endif %}
	{% set z = 10 %}
	{% endif %}
	
	{% set start_z_offset = 0 %}
	{% set end_z_offset = 0 %}
	{% if has_start_offset_t0 %}
	{% set start_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) %}
	{% set end_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_end_result|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t0) ) }
	{% endif %}
	{% if end_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t0) )  }
	{% endif %}
	{% set start_z_offset = start_z_probe_result_t0 %}
	{% set end_z_offset = end_z_probe_result_t0 %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	{% if current_toolhead == 1 or both_toolheads or target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	{% if has_start_offset_t1 %}
	{% set start_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) %}
	{% set end_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_end_result_t1|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t1) ) }
	{% endif %}
	{% if end_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t1) ) }
	{% endif %}
	{% set start_z_offset = [start_z_offset, start_z_probe_result_t1]|max %}
	{% set end_z_offset = [end_z_offset, start_z_probe_result_t1]|max %}
	{% endif %}
	{% endif %}
	{% if target_idex_mode != 'copy' and target_idex_mode != 'mirror' %}
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% set original_start_z_offset = start_z_offset %}
	{% set original_end_z_offset = end_z_offset %}
	{% set start_z_offset = original_end_z_offset %}
	{% set end_z_offset = original_start_z_offset %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	DEBUG_ECHO PREFIX="PRIME_BLOB" MSG="x_start: {x_start}, y_start: {y_start}, x_factor: {x_factor}, y_factor: {y_factor}, z: {z}, start_z_offset: {start_z_offset}, end_z_offset: {end_z_offset}"
	
	
	G90
	
	M83
	RATOS_ECHO PREFIX="Priming" MSG="Lifting Z to {z}.."
	
	G0 Z{z} F{z_speed}
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% if start_print_park_in != 'primeblob' %}
	G1 X{x_start} F{speed}
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% endif %}
	{% else %}
	
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% if target_idex_mode=="copy" or target_idex_mode=="mirror" %}
	RATOS_ECHO PREFIX="Priming" MSG="Mirroring move to {x_start}, {y_start} along the edge of the print area.."
	
	_IDEX_MIRROR PRIMING=1
	{% else %}
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% endif %}
	G1 X{x_start} F{speed}
	{% endif %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Starting prime blob.."
	
	G1 Z{0.5 + start_z_offset} F{z_speed}
	
	G1 Y{y_start} F{speed}
	
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	
	M106 S{fan_speed}
	
	G1 Z5 F100 E5
	G92 E0
	RATOS_ECHO PREFIX="Priming" MSG="Bridging with {((fan_speed/255) * 100)|int}% fan speed.."
	
	G1 F3000 X{x_start + (15 * x_factor)} Y{y_start + (15 * y_factor)} E{1 / ((0.4 / nozzle_diameter) ** 2)}
	
	
	
	G1 F3000 X{x_start + (20 * x_factor)} Y{y_start + (20 * y_factor)} Z{3.8 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (34 * x_factor)} Y{y_start + (34 * y_factor)} Z{2.6 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (38 * x_factor)} Y{y_start + (38 * y_factor)} Z{1.4 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (42 * x_factor)} Y{y_start + (42 * y_factor)} Z{0.2 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	
	M106 S0
	
	G1 F3000 X{x_start + (46 * x_factor)} Y{y_start + (46 * y_factor)} Z{0.2 + end_z_offset} E0.6
	
	G1 F{speed} X{x_start + (50 * x_factor)} Y{y_start + (50 * y_factor)}
	
	
	{% if target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if target_idex_mode == "copy" %}
	{% if first_y >= 0 %}
	_IDEX_COPY DANCE=0 Y={first_y}
	{% else %}
	_IDEX_COPY DANCE=0 Y={params.Y1}
	{% endif %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	RESTORE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="prime_blob"
	
	
	G92 E0

[gcode_macro UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set temp = params.TEMP|default(220)|int %}
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_UNLOAD_FILAMENT TEMP={temp} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_UNLOAD_FILAMENT]
description = Unload filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_UNLOAD_FILAMENT" MSG="TEMP: {temp}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=unload_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	G4 P3000
	
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD=0 NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=unload_state
	
	
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament unloading completed"

[gcode_macro _IDEX_UNLOAD_FILAMENT]
description = Unload filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading T{toolhead} filament..."
	
	DEBUG_ECHO PREFIX="_IDEX_UNLOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} AUTOMATED={automated}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="T{toolhead} filament unloading completed"

[gcode_macro _UNLOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LEGACY_UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
gcode = 
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set unload_speed = 5 * 60 %}
	{% set unload_length = printer["gcode_macro RatOS"].filament_unload_length|float %}
	M117 Unloading filament...
	
	G0 E10 F300
	
	G0 E-5 F3600
	
	G4 P3000
	
	G0 E5 F6000
	
	G0 E-15 F6000
	
	G0 E-{unload_length} F{unload_speed}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}
	M117 Filament unloaded!
	RESPOND MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	RATOS_ECHO MSG="Unloading filament from nozzle to cooling zone... Please wait!"
	
	_PURGE_BEFORE_UNLOAD TOOLHEAD={toolhead}
	
	{% if printer["gcode_macro _UNLOAD_WITHOUT_TIP_FORMING"] is defined %}
	
	_UNLOAD_WITHOUT_TIP_FORMING TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	_UNLOAD_WITH_TIP_FORMING NAME='{filament_name}' TYPE='{filament_type}'
	{% endif %}
	
	G4 P3000

[gcode_macro _UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	{% set tooolhead_sensor_to_extruder_gear_distance = printer["gcode_macro T%s" % toolhead].tooolhead_sensor_to_extruder_gear_distance|float %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER" MSG="TOOLHEAD: {toolhead}"
	
	
	G0 E-{extruder_gear_to_cooling_position_distance + tooolhead_sensor_to_extruder_gear_distance + 50} F{extruder_load_speed}
	
	RATOS_ECHO MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_WITH_TIP_FORMING]
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	{% if filament_name != '' and filament_type != '' %}
	_UNLOAD_KNOWN_FILAMENT NAME={filament_name} TYPE={filament_type}
	{% else %}
	_UNLOAD_UNKNOWN_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _UNLOAD_KNOWN_FILAMENT]
description = User overrideable tip forming macro if slicer filament profiles are known
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	RATOS_ECHO PREFIX="FILAMENT TYPE" MSG='{filament_type}'
	RATOS_ECHO PREFIX="FILAMENT PROFILE" MSG='{filament_name}'
	
	
	{% if filament_name == "Prusament PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% elif filament_name == "Nobufil PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% else %}
	
	RATOS_ECHO PREFIX="_UNLOAD_KNOWN_FILAMENT" MSG="Filament profile not found!"
	_UNLOAD_UNKNOWN_FILAMENT
	{% endif %}

[gcode_macro _UNLOAD_UNKNOWN_FILAMENT]
description = User overrideable standard tip forming macro
gcode = 
	
	DEBUG_ECHO PREFIX="_UNLOAD_UNKNOWN_FILAMENT" MSG="Using standard tip forming macro!"
	
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10

[gcode_macro _TIP_FORMING]
gcode = 
	
	{% set cooling_moves = params.COOLING_MOVES|default(4)|int %}
	{% set cooling_move_length = params.COOLING_MOVE_LENGTH|default(10)|float %}
	{% set start_cooling_speed = params.START_COOLING_SPEED|default(10)|float * 60 %}
	{% set end_cooling_speed = params.END_COOLING_SPEED|default(50)|float * 60 %}
	{% if cooling_moves == 0 %}
	{% set cooling_move_length = 0 %}
	{% endif %}
	
	
	{% set dip = true if params.DIP|default(false)|lower == "true" else false %}
	{% set dip_length = params.DIP_LENGTH|default(22)|float %}
	{% set dip_speed = params.DIP_SPEED|default(30)|float * 60 %}
	{% set dip_retract_speed = params.DIP_RETRACT_SPEED|default(70)|float * 60 %}
	
	
	{% set retract_length = params.RETRACT_LENGTH|default(18)|float %}
	{% set start_retract_speed = params.START_RETRACT_SPEED|default(120)|float * 60 %}
	{% set end_retract_speed = params.END_RETRACT_SPEED|default(20)|float * 60 %}
	
	DEBUG_ECHO PREFIX="_TIP_FORMING" MSG="cooling_moves: {cooling_moves}, cooling_move_length: {cooling_move_length}, start_cooling_speed: {start_cooling_speed}, end_cooling_speed: {end_cooling_speed}, dip: {dip}, dip_length: {dip_length}, dip_speed: {dip_speed}, dip_retract_speed: {dip_retract_speed}, retract_length: {retract_length}, start_retract_speed: {start_retract_speed}, end_retract_speed: {end_retract_speed}"
	
	M220 S100
	
	
	G92 E0
	{% set retract = retract_length + cooling_move_length / 2 - 15 %}
	G1 E-15 F{start_retract_speed}
	G1 E-{0.7 * retract} F{1.0 * end_retract_speed}
	G1 E-{0.2 * retract} F{0.5 * end_retract_speed}
	G1 E-{0.1 * retract} F{0.3 * end_retract_speed}
	
	
	G92 E0
	{% if cooling_moves > 0 %}
	{% set i = (end_cooling_speed - start_cooling_speed) / (2 * cooling_moves - 1) %}
	{% for m in range(cooling_moves) %}
	G1 E{cooling_move_length} F{(start_cooling_speed + i * m * 2)}
	G1 E-{cooling_move_length} F{(start_cooling_speed + i * (m * 2 + 1))}
	{% endfor %}
	{% endif %}
	
	
	G92 E0
	{% if dip %}
	G1 E{dip_length} F{dip_speed}
	G4 P100
	G1 E-{dip_length} F{dip_retract_speed}
	{% endif %}
	
	G92 E0
	M400

[delayed_gcode __ON_FILAMENT_SENSOR_BUTTON_PRESSED_STARTUP_GUARD]
initial_duration = 2.
gcode = 
	SET_GCODE_VARIABLE MACRO=_ON_FILAMENT_SENSOR_BUTTON_PRESSED VARIABLE=startup_complete VALUE=True

[gcode_macro _ON_FILAMENT_SENSOR_BUTTON_PRESSED]
variable_startup_complete = False
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set toolhead_sensor_button_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_sensor_button_only_when_sensor_enabled|default(false)|lower == 'true' %}
	
	
	{% if not startup_complete and sensor_enabled %}
	{action_emergency_stop("RatOS: The T%s filament sensor button was triggered immediately on printer startup. This is likely a false trigger. Please check your filament sensor wiring and configuration!" % (toolhead,))}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_SENSOR_BUTTON_PRESSED" MSG="TOOLHEAD: {toolhead}, SENSOR_ENABLED: {sensor_enabled}, TOOLHEAD_SENSOR_BUTTON_ONLY_WHEN_SENSOR_ENABLED: {toolhead_sensor_button_only_when_sensor_enabled}"
	
	{% if not printer.virtual_sdcard.is_active and (sensor_enabled or not toolhead_sensor_button_only_when_sensor_enabled) %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	{% set toolhead_detect_clog_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_detect_clog_only_when_sensor_enabled|default(true)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}, ENABLE_CLOG_DETECTION: {enable_clog_detection}, TOOLHEAD_DETECT_CLOG_ONLY_WHEN_SENSOR_ENABLED: {toolhead_detect_clog_only_when_sensor_enabled}, SENSOR_ENABLED: {sensor_enabled}"
	
	{% if enable_clog_detection and (sensor_enabled or not toolhead_detect_clog_only_when_sensor_enabled) %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_clog_detection %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_FILAMENT_END]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set clogged = true if params.CLOGGED|default(false)|lower == 'true' else false %}
	
	
	{% set unload_after_runout = printer["gcode_macro T%s" % toolhead].unload_after_runout|float %}
	
	
	{% if clogged %}
	_LED_FILAMENT_CLOG TOOLHEAD={toolhead}
	{% else %}
	_LED_FILAMENT_RUNOUT TOOLHEAD={toolhead}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_END" MSG="TOOLHEAD: {toolhead}"
	
	{% if printer.virtual_sdcard.is_active %}
	{% if not printer.pause_resume.is_paused %}
	PAUSE RUNOUT=True
	{% endif %}
	{% if not clogged and unload_after_runout %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	{% if not clogged and printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true'%}
	_JOIN_SPOOL TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M600]
description = Executes a color change by pausing the printer an unloading the filament.
gcode = 
	PAUSE
	UNLOAD_FILAMENT AUTOMATED=True
	RATOS_ECHO MSG="Please load new filament and resume"

[gcode_macro COLD_PULL]
description = Automated hotend cold pull.
gcode = 
	
	{% set extrusion_temp = params.EXTRUSION_TEMP|default(220)|int %}
	{% set cold_pull_temp = params.COLD_PULL_TEMP|default(80)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	
	{% if printer["dual_carriage"] is not defined %}
	{% set toolhead = 0 %}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead != 0 and toolhead != 1 %}
	{action_raise_error("Please select toolhead! 0 = left, 1 = right toolhead")}
	{% endif %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	RATOS_ECHO MSG="Starting cold pull on T{toolhead}..."
	{% else %}
	RATOS_ECHO MSG="Starting cold pull..."
	{% endif %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	SAVE_GCODE_STATE NAME=cold_pull_state
	
	
	{% if printer["dual_carriage"] is defined and "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	RATOS_ECHO MSG="Heating T{toolhead} to {extrusion_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={extrusion_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={extrusion_temp} MAXIMUM={extrusion_temp + 2}
	
	
	G4 P3000
	
	
	RATOS_ECHO MSG="extruding..."
	G92 E0
	G1 E30 F300
	G92 E0
	
	
	RATOS_ECHO MSG="Cooling T{toolhead} to {cold_pull_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={cold_pull_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={cold_pull_temp} MAXIMUM={cold_pull_temp + 2}
	
	
	G4 P10000
	
	
	RATOS_ECHO MSG="cold pull..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-40 VELOCITY=5 ACCEL=100
	
	
	RATOS_ECHO MSG="eject filament..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-200 VELOCITY=20 ACCEL=500
	
	
	RATOS_ECHO MSG="cooling down extruder..."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	RESTORE_GCODE_STATE NAME=cold_pull_state
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	
	CONSOLE_ECHO TITLE="Cold pull complete" MSG="Please remove the filament from the PTFE tube and cut the end off. Do NOT try to load it again." TYPE="warning"

[gcode_macro _USER_START_PRINT_BEFORE_HOMING]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_BED]
gcode = 

[gcode_macro _USER_START_PRINT_BED_MESH]
gcode = 

[gcode_macro _USER_START_PRINT_PARK]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 

[gcode_macro _USER_START_PRINT_HEAT_CHAMBER]
description = Uses the extruder sensor to wait for chamber temp. Override the _START_PRINT_HEAT_CHAMBER macro to implement heated chamber handling.
gcode = 
	
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}

[gcode_macro _USER_END_PRINT_BEFORE_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_AFTER_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_PARK]
gcode = 

[gcode_macro _USER_END_PRINT_FINISHED]
description = User hook for when the print is finished after gcode state has been restored.
gcode = 

[gcode_macro _USER_START_PRINT]
gcode = 

[gcode_macro _USER_END_START_PRINT]
gcode = 

[gcode_macro _USER_START_FEATURE]
gcode = 

[gcode_macro _USER_END_FEATURE]
gcode = 

[gcode_macro _USER_BEFORE_IDLE_TIMEOUT]
gcode = 

[gcode_macro _USER_AFTER_IDLE_TIMEOUT]
gcode = 

[gcode_macro ECHO_T_VARS]
description = Echo Toolhead variables to the console.
gcode = 
	{% set t = params.T|default(0) %}
	RATOS_ECHO MSG="T{t} Variables"
	{% for var, value in printer["gcode_macro T%s" % t].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ECHO_RATOS_VARS]
description = Echo RatOS variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro RatOS"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ENSURE_CRITICAL_RATOS_INIT]
variable_completed = False
gcode = 
	{% if not completed %}
	CALCULATE_PRINTABLE_AREA
	SET_GCODE_VARIABLE MACRO=ENSURE_CRITICAL_RATOS_INIT VARIABLE=completed VALUE=True
	{% endif %}

[delayed_gcode RATOS_INIT]
initial_duration = 0.1
gcode = 
	{action_respond_info("Initializing RatOS...")}
	ENSURE_CRITICAL_RATOS_INIT
	_LED_STANDBY
	INITIAL_FRONTEND_UPDATE
	_CHAMBER_FILTER_SANITY_CHECK
	{% if printer.fastconfig.settings.beacon is defined %}
	
	_BED_MESH_SANITY_CHECK
	{% endif %}
	{% set svv = printer.save_variables.variables %}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=0 C={svv.nozzle_expansion_coefficient_t0|default(0.06)|float}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=1 C={svv.nozzle_expansion_coefficient_t1|default(0.06)|float}
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=idex_applied_offset

[delayed_gcode RATOS_LOGO]
initial_duration = 2
gcode = 
	
	
	
	
	
	ENSURE_CRITICAL_RATOS_INIT
	HELLO_RATOS
	_ALERT_NON_ZERO_Z_OFFSET

[gcode_macro _ALERT_NON_ZERO_Z_OFFSET]
gcode = 
	{% set force = params.FORCE|default(0)|int == 1 %}
	{% set user_offset = printer.named_offsets.user_probe_z_offset.z|float %}
	{% set gcode_offset = printer.gcode_move.homing_origin.z|float %}
	{% set combined_offset = user_offset + gcode_offset %}
	
	{% if force or user_offset != 0 or gcode_offset != 0 %}
	{% set title = "User-adjusted Z-offset of %.3f mm is active" % combined_offset %}
	{% set msg = "" %}
	{% set nl = "" %}
	{% if user_offset != 0 %}
	{% set msg = msg + "beacon true zero user Z-offset: %.3f mm (to clear, use Z_OFFSET_APPLY_PROBE CLEAR=1)" % user_offset %}
	{% set nl = "_N_" %}
	{% endif %}
	{% if gcode_offset != 0 %}
	{% set msg = msg + nl + "G-code Z-offset: %.3f mm" % gcode_offset %}
	{% endif %}
	CONSOLE_ECHO TITLE="{title}" TYPE="info" MSG="{msg}"
	{% endif %}

[gcode_macro _INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE]
gcode = 
	{% set variable = params.VARIABLE|string %}
	{% set svv = printer.save_variables.variables %}
	{% set nlu_msg = "no longer used, please remove" %}
	{% if svv[variable] is defined %}
	{% set v = svv[variable]|string|replace('"', '')|replace("'", "") %}
	{% if not nlu_msg in v %}
	SAVE_VARIABLE VARIABLE={variable} VALUE='"{nlu_msg} (was {v})"'
	{% endif %}
	CONSOLE_ECHO TITLE="Deprecated ratos-variables.cfg variable" TYPE="warning" MSG="The variable {variable} is no longer used, please remove it from your ratos-variables.cfg file."
	{% endif %}

[gcode_macro _NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK]
gcode = 
	
	
	
	
	
	
	
	{% set t = params.T|int %}
	{% set c = params.C|float %}
	{% set normal_low = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_low|default(0.05)|float %}
	{% set normal_high = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_high|default(0.10)|float %}
	
	{% if c < 0 %}
	
	{action_emergency_stop("Invalid nozzle_expansion_coefficient_t%s value in ratos-variables.cfg: %.3f. It must be non-negative." % (t, c))}
	{% endif %}
	{% if c >= normal_high %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite high. Please verify that this is correct."
	{% endif %}
	{% if c <= normal_low %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite low. Please verify that this is correct."
	{% endif %}

[gcode_macro INITIAL_FRONTEND_UPDATE]
gcode = 
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_error = printer["gcode_macro RatOS"].status_color_error|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_unknown}"'
	{% endif %}
	
	
	{% set t0_sensor = "undefined" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	{% set t0_sensor = "detected" %}
	{% else %}
	{% set t0_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t0_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	{% set t1_sensor = "undefined" %}
	{% if printer["dual_carriage"] is defined and printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	{% set t1_sensor = "detected" %}
	{% else %}
	{% set t1_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t1_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	{% if svv.t0_filament is defined and printer["gcode_macro T0"] is defined %}
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	{% if t0_sensor != "empty" %}
	{% set t0_filament_type = svv.t0_filament[0]|default('')|string %}
	{% set t0_filament_name = svv.t0_filament[1]|default('')|string %}
	{% set t0_filament_temp = svv.t0_filament[2]|default(0)|float %}
	{% if t0_filament_name != '' and t0_filament_type != '' and t0_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{t0_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{t0_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={t0_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}
	{% if svv.t1_filament is defined and printer["gcode_macro T1"] is defined %}
	{% if printer["gcode_macro T1"].filament_name is defined and printer["gcode_macro T1"].filament_type is defined and printer["gcode_macro T1"].filament_temp is defined %}
	{% if t1_sensor != "empty" %}
	{% set t1_filament_type = svv.t1_filament[0]|default('')|string %}
	{% set t1_filament_name = svv.t1_filament[1]|default('')|string %}
	{% set t1_filament_temp = svv.t1_filament[2]|default(0)|float %}
	{% if t1_filament_name != '' and t1_filament_type != '' and t1_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='"{t1_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='"{t1_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE={t1_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t1_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro CALCULATE_PRINTABLE_AREA]
variable_calculated = False
gcode = 
	{% if not calculated %}
	{% set bed_margin_x = printer["gcode_macro RatOS"].bed_margin_x %}
	{% set bed_margin_y = printer["gcode_macro RatOS"].bed_margin_y %}
	
	
	
	{% set tool = 0 if printer["gcode_macro T0"] is not defined or printer["gcode_macro T0"].active else 1 %}
	{% set max_x = printer.toolhead.axis_maximum.x if printer["dual_carriage"] is defined and tool == 0 else printer.toolhead.axis_maximum.x - bed_margin_x[1] %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	
	
	{% set max_x = printer.toolhead.axis_maximum.x %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="printer.toolhead.axis_maximum.x {printer.toolhead.axis_maximum.x}"
	
	{% set max_y = printer.toolhead.axis_maximum.y - bed_margin_y[1]%}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_x_max VALUE={max_x}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_y_max VALUE={max_y}
	SET_GCODE_VARIABLE MACRO=CALCULATE_PRINTABLE_AREA VARIABLE=calculated VALUE=True
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	RATOS_LOG PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	{% endif %}

[gcode_macro CACHE_TOOLHEAD_SETTINGS]
variable_cache = {"global": {"accel": 1000, "ratio": 0.5, "speed": 50, "scv": 5}}
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set dummy = cache.__setitem__(key, {"accel": printer.toolhead.max_accel, "ratio": printer.toolhead.minimum_cruise_ratio, "speed": printer.toolhead.max_velocity, "scv": printer.toolhead.square_corner_velocity}) %}
	SET_GCODE_VARIABLE MACRO=CACHE_TOOLHEAD_SETTINGS VARIABLE=cache VALUE="{cache | pprint | replace("\n", "") | replace("\"", "\\\"")}"
	DEBUG_ECHO PREFIX="CACHE_TOOLHEAD_SETTINGS" MSG="Toolhead settings cached for {key}. {printer.toolhead.max_accel} accel, {printer.toolhead.minimum_cruise_ratio} ratio, {printer.toolhead.max_velocity} velocity, {printer.toolhead.square_corner_velocity} scv."

[gcode_macro RESTORE_TOOLHEAD_SETTINGS]
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set values = printer["gcode_macro CACHE_TOOLHEAD_SETTINGS"].cache.__getitem__(key) %}
	{% if values is not defined or values == 'None' %}
	{ action_raise_error("RESTORE_TOOLHEAD_SETTINGS: Toolhead settings not cached for key '" ~ key ~ "'.") }
	{% endif %}
	SET_VELOCITY_LIMIT ACCEL={values.accel} MINIMUM_CRUISE_RATIO={values.ratio} VELOCITY={values.speed} SQUARE_CORNER_VELOCITY={values.scv}
	DEBUG_ECHO PREFIX="RESTORE_TOOLHEAD_SETTINGS" MSG="Toolhead settings restored. {values.accel} accel, {values.ratio} ratio, {values.speed} velocity, {values.scv} scv."

[gcode_macro SET_MACRO_TRAVEL_SETTINGS]
gcode = 
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float %}
	{% set accel = printer["gcode_macro RatOS"].macro_travel_accel %}
	SET_VELOCITY_LIMIT ACCEL={accel} MINIMUM_CRUISE_RATIO=0.5 VELOCITY={speed} SQUARE_CORNER_VELOCITY={5}
	DEBUG_ECHO PREFIX="SET_MACRO_TRAVEL_SETTINGS" MSG="Macro travel settings set. {accel} accel, {speed} velocity"

[gcode_macro SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% if printer["dual_carriage"] is not defined %}
	
	SET_KINEMATIC_POSITION X={printable_x_max / 2} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	{% else %}
	
	IDEX_SET_CENTER_KINEMATIC_POSITION
	{% endif %}

[gcode_macro IDEX_SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x - (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x + (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY

[gcode_macro VERIFY_HYBRID_INVERTED]
gcode = 
	
	{% set inverted = False %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy is defined and printer.fastconfig.settings.ratos_hybrid_corexy.inverted is defined %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy.inverted|lower == 'true' %}
	{% set inverted = True %}
	{% endif %}
	{% endif %}
	{% if inverted == False %}
	{ action_emergency_stop("ratos_hybrid_corexy NOT INVERTED! Inverted hybrid core-xy bugfix not detected.") }
	{% endif %}

[gcode_macro RATOS_ECHO]
gcode = 
	{% set prefix = "RatOS" %}
	{% set debug = params.DEBUG|default(0)|int %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " | " ~ params.PREFIX %}
	{% endif %}
	{% set prefix = prefix ~ ":" %}
	{% set msg = "" %}
	{% if params.MSG is defined %}
	{% set msg = params.MSG %}
	{% else %}
	{% set msg = "No msg parameter provided (this is a bug or unintended use)." %}
	{% endif %}
	{% if not debug %}
	
	M117 {prefix} {msg}
	{% endif %}
	RATOS_LOG PREFIX="{prefix}" MSG="{msg}"
	{% if not debug %}
	RESPOND PREFIX="{prefix}" MSG="{msg}"
	{% else %}
	CONSOLE_ECHO TITLE="{prefix}" TYPE="debug" MSG="{msg}"
	{% endif %}

[gcode_macro ENABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=True
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=prefix_filter VALUE="'{params.FILTER|default('')|lower}'"
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging enabled."

[gcode_macro DISABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=False
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging disabled."

[gcode_macro DEBUG_ECHO]
variable_enabled = False
variable_prefix_filter = ''
gcode = 
	{% set prefix = "DEBUG" %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " - " ~ params.PREFIX %}
	{% endif %}
	{% if enabled and (prefix_filter|lower == '' or prefix_filter|lower in params.PREFIX|lower) %}
	RATOS_ECHO PREFIX="{prefix}" MSG="{params.MSG}" DEBUG=1
	{% endif %}

[gcode_macro START_FEATURE]
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="Start {params.FEATURE} feature gcode"
	{% set scv = printer.toolhead.square_corner_velocity|int|default(5) %}
	{% set accel = printer.toolhead.max_accel|int|default(10000) %}
	{% set ratio = printer.toolhead.minimum_cruise_ratio|float|default(0.5) %}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="scv" VALUE={scv}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="accel" VALUE={accel}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="ratio" VALUE={ratio}
	_USER_START_FEATURE FEATURE="{params.FEATURE}"

[gcode_macro END_FEATURE]
variable_scv = 5
variable_accel = 10000
variable_ratio = 0.5
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="End {params.FEATURE} feature gcode"
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={scv} ACCEL={accel} MINIMUM_CRUISE_RATIO={ratio}
	_USER_END_FEATURE FEATURE="{params.FEATURE}" SCV={scv} ACCEL={accel} RATIO={ratio}

[gcode_macro _ON_LAYER_CHANGE]
variable_layer_number = 0
description = INTERNAL USE ONLY. Call it from the slicers after layer change custom gcode
gcode = 
	
	{% set layer = params.LAYER|int %}
	
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE={layer}
	SET_PRINT_STATS_INFO CURRENT_LAYER={layer}

[gcode_macro _LEARN_MORE_CALIBRATION]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/calibration" %}
	{% set link_text = "RatOS Calibration Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_CHAMBER_FILTER]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter Control" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_FILAMENT]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/filaments" %}
	{% set link_text = "RatOS Filament Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _CONSOLE_SAVE_CONFIG]
gcode = 
	M118 Click <a class="command text--blue">SAVE_CONFIG</a> to save the settings to your printer.cfg.

[gcode_macro _LOAD_RATOS_SKEW_PROFILE]
gcode = 
	{% set ratos_skew_profile = printer["gcode_macro RatOS"].skew_profile|default("") %}
	{% if ratos_skew_profile != "" %}
	{% if printer.fastconfig.config["skew_correction %s" % ratos_skew_profile] is defined %}
	SKEW_PROFILE LOAD={ratos_skew_profile}
	GET_CURRENT_SKEW
	{% else %}
	{% set line_1 = '"Could not find skew profile %s!_N_Clearing skew correction."' % ratos_skew_profile %}
	CONSOLE_ECHO TITLE="Missing skew profile!" TYPE="warning" MSG={line_1}
	SET_SKEW CLEAR=1
	{% endif %}
	{% endif %}

[gcode_macro M601]
gcode = 
	PAUSE

[gcode_macro _STOP_AND_RAISE_ERROR]
gcode = 
	M84
	_RAISE_ERROR MSG="{params.MSG}"

[gcode_macro _RESET_GCODE_VARIABLES]
description = Reset specified [gcode_macro ...] variables to their original values from configuration when Klipper started.
	- MACRO: Name of the GCODE macro containing the variables to reset.
	- VARIABLES: Comma-separated list of variable names to reset (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- QUIET: (optional) If true, suppresses console echo messages for each reset variable. Default is false.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set quiet = params.QUIET|default("false")|lower in ("true", "1", "yes") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	{% set settings = printer.fastconfig.settings[obj_name|lower] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro %s]" % macro) }
	{% endif %}
	
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if settings["variable_%s" % var] is not defined %}
	{ action_raise_error("Variable '%s' is not defined in settings for [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	
	{% for var in vars %}
	{% set var_value = obj[var] %}
	{% if var_value is defined %}
	{% set v = settings["variable_%s" % var] %}
	{% if v != var_value|string %}
	{% if var_value is string %}
	{% set v = '"\'' ~ v|replace('"', '\\"')|replace("'", "\\'") ~ '\'"' %}
	{% endif %}
	SET_GCODE_VARIABLE MACRO={macro} VARIABLE={var} VALUE={v}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Reset {macro} variable {var} to original value: {v} (was {obj[var]})"
	{% endif %}
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro _SHOW_GCODE_VARIABLES]
description = Show current values of specified [gcode_macro ...] variables.
	- MACRO: Name of the GCODE macro containing the variables to show.
	- VARIABLES: Comma-separated list of variable names to show (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- PAD: (optional) If defined, provide a single character to use for padding variable names to align values in a tabular format in the console output. Default is no padding.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set pad = params.PAD|default("") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	
	{% set ns = namespace() %}
	{% set ns.max_len = 0 %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% set ns.max_len = (ns.max_len, var|length)|max %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if pad %}
	{% set padding = pad * (ns.max_len - var|length) %}
	CONSOLE_ECHO MSG="{var}{padding} {obj[var]}"
	{% else %}
	CONSOLE_ECHO MSG="{var}: {obj[var]}"
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro PAUSE]
description = Pauses the print
rename_existing = PAUSE_BASE
variable_extrude = 1.5
variable_retract = 1.5
variable_fan_speed = 0
variable_idex_mode = ""
variable_idex_toolhead = 0
variable_idex_toolhead_x = 0.0
variable_idex_toolhead_y = 0.0
variable_idex_toolhead_z = 0.0
gcode = 
	RATOS_ECHO MSG="Pausing print..."
	
	
	{% set runout_detected = true if params.RUNOUT|default(false)|lower == 'true' else false %}
	
	
	_LED_PAUSE
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	SAVE_GCODE_STATE NAME=PAUSE_state
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_mode VALUE='"{idex_mode}"'
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={idex_toolhead}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_x VALUE={printer.gcode_move.gcode_position.x|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_y VALUE={printer.gcode_move.gcode_position.y|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_z VALUE={printer.gcode_move.gcode_position.z|float}
	DEBUG_ECHO PREFIX="PAUSE" MSG="idex_mode: {idex_mode}, idex_toolhead: {idex_toolhead}, idex_toolhead_x: {idex_toolhead_x}, idex_toolhead_y: {idex_toolhead_y}, idex_toolhead_z: {idex_toolhead_z}"
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="pause"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if current_z < (max_z - 20.0) %}
	{% set z_safe = 20.0 %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	PAUSE_BASE
	
	
	{% if printer["dual_carriage"] is not defined %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan"].speed|float}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	{% if idex_toolhead == 0 %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t1"].speed|float}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106 S0
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set R = printer["gcode_macro PAUSE"].retract|float %}
	{% if can_extrude %}
	G91
	G1 E-{R} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	{% set pause_print_park_x = printer["gcode_macro RatOS"].pause_print_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].pause_print_park_in %}
	{% if runout_detected %}
	{% set pause_print_park_x = printer["gcode_macro RatOS"].runout_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].runout_park_in %}
	{% endif %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	DEBUG_ECHO PREFIX="PAUSE" MSG="z_speed: {z_speed}, pause_print_park_x: {pause_print_park_x}, pause_print_park_in: {pause_print_park_in}, default_toolhead: {default_toolhead}"
	{% if "xyz" in printer.toolhead.homed_axes %}
	G91
	G1 Z{z_safe} F{z_speed}
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% else %}
	
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	_IDEX_SINGLE X={parking_position}
	{% else %}
	PARK_TOOLHEAD
	{% endif %}
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="pause"
	
	RATOS_ECHO MSG="Print paused"

[gcode_macro RESUME]
description = Resumes the print if the printer is paused.
rename_existing = RESUME_BASE
gcode = 
	
	
	RATOS_ECHO MSG="Resuming print..."
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	
	{% set target_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set target_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if target_idex_mode != '' %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set fan_speed = printer["gcode_macro PAUSE"].fan_speed|float %}
	{% if printer["dual_carriage"] is not defined %}
	M106 S{(fan_speed * 255)}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% else %}
	{% if params.TOOLHEAD is defined %}
	
	{% if params.TOOLHEAD == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% else %}
	{% if printer["gcode_macro PAUSE"].idex_toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	{% if params.TOOLHEAD is defined %}
	_SELECT_TOOL T={params.TOOLHEAD} X=-1 Y=-1 TOOLSHIFT=false
	{% else %}
	_SELECT_TOOL T={printer["gcode_macro PAUSE"].idex_toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	{% endif %}
	
	{% set x = printer["gcode_macro PAUSE"].idex_toolhead_x|float %}
	{% set y = printer["gcode_macro PAUSE"].idex_toolhead_y|float %}
	{% set z = printer["gcode_macro PAUSE"].idex_toolhead_z|float %}
	G1 X{x} Y{y} Z{z} F{speed}
	{% if params.TOOLHEAD is defined %}
	
	SAVE_GCODE_STATE NAME=PAUSE_STATE
	{% endif %}
	{% endif %}
	
	
	{% if params.TOOLHEAD is not defined %}
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% if can_extrude %}
	G91
	G1 E{E} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1 MOVE_SPEED={speed}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	RESUME_BASE
	
	
	_LED_PRINTING
	
	RATOS_ECHO MSG="Print resumed"

[gcode_macro CANCEL_PRINT]
description = Cancels the print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	RATOS_ECHO MSG="Cancelling print..."
	END_PRINT
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	
	CANCEL_PRINT_BASE
	RATOS_ECHO MSG="Print cancelled"

[gcode_macro START_PRINT]
description = Start print procedure, use this in your Slicer.
variable_post_processor_version = 2
variable_is_printing_gcode = False
variable_both_toolheads = True
variable_object_xoffset = 0
variable_first_x = -1
variable_first_y = -1
variable_total_toolshifts = 0
variable_initial_tool = 0
variable_extruder_first_layer_temp = ""
variable_extruder_other_layer_temp = ""
gcode = 
	
	{% if params.EXTRUDER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_TEMP parameter not found.")}
	{% endif %}
	{% if params.EXTRUDER_OTHER_LAYER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_OTHER_LAYER_TEMP parameter not found.")}
	{% endif %}
	{% if params.BED_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. BED_TEMP parameter not found.")}
	{% endif %}
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' and printer["gcode_macro RatOS"].danger_force_allow_auto_center_subject|default(false)|lower != 'true'%}
	
	
	
	
	
	{ action_raise_error("The experimental auto_center_subject feature is not supported in this version of RatOS. Please disable it in the RatOS macro settings.") }
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes and printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% if printer["gcode_macro _VAOC"].is_started|default(true)|lower == 'true' %}
	_VAOC_END
	{% endif %}
	{% endif %}
	
	
	_LED_START_PRINTING
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_USER_START_PRINT { rawparams }
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_probe_stowable = printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% endif %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	{% set X0 = params.X0|default(-1)|float %}
	{% set X1 = params.X1|default(-1)|float %}
	{% set Y0 = params.Y0|default(-1)|float %}
	{% set Y1 = params.Y1|default(-1)|float %}
	{% if first_x == -1 or first_y == -1 %}
	{% set first_x = params.FIRST_X|default(-1)|float %}
	{% set first_y = params.FIRST_Y|default(-1)|float %}
	{% endif %}
	{% set total_toolshifts = params.TOTAL_TOOLSHIFTS|default(0)|int %}
	{% set initial_tool = params.INITIAL_TOOL|default(default_toolhead)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	
	
	
	
	
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(printer.heater_bed.target, true)|float %}
	
	
	{% set total_layer_count = params.TOTAL_LAYER_COUNT|default(0)|int %}
	{% set extruder_first_layer_temp = (params.EXTRUDER_TEMP|default("")).split(",") %}
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL BEACON_CONTACT_START_PRINT_TRUE_ZERO={beacon_contact_start_print_true_zero} BEACON_CONTACT_CALIBRATE_MODEL_ON_TRUE_ZERO={beacon_contact_calibrate_model_on_true_zero}
	{% endif %}
	
	_START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH BED_TEMP={bed_temp}
	
	
	RATOS_ECHO MSG="First print coordinates X:{first_x} Y:{first_y}"
	
	
	{% if params.TOTAL_LAYER_COUNT is not defined %}
	{% set link_url = "https://os.ratrig.com/docs/slicers" %}
	{% set link_text = "RatOS Slicer Configuration" %}
	{% set line_1 = '"Your slicer gcode settings are not up to date._N_Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="Incomplete Slicer Configuration detected" TYPE="warning" MSG={line_1}
	{% endif %}
	
	
	SET_PRINT_STATS_INFO CURRENT_LAYER=1
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE=1
	{% if total_layer_count > 0 %}
	SET_PRINT_STATS_INFO TOTAL_LAYER={total_layer_count}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads %}
	{% set initial_tool = 0 if initial_tool == 1 else 1 %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	{% endif %}
	
	
	{% set both_toolheads = true %}
	{% if total_toolshifts == 0 %}
	{% set both_toolheads = false %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	{% endif %}
	{% if both_toolheads and (idex_mode == "copy" or idex_mode == "mirror") %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Gcode tool changes found. Copy and mirror mode do not support toolchanges.")}
	{% endif %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set both_toolheads = true %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=initial_tool VALUE={initial_tool}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_x VALUE={first_x}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_y VALUE={first_y}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=total_toolshifts VALUE={total_toolshifts}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=both_toolheads VALUE={both_toolheads}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_first_layer_temp VALUE="'{params.EXTRUDER_TEMP}'"
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_other_layer_temp VALUE="'{params.EXTRUDER_OTHER_LAYER_TEMP}'"
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE=0
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set svv = printer.save_variables.variables %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set stepper_x_position_min = printer.fastconfig.settings.stepper_x.position_min|float %}
	{% set stepper_x_position_endstop = printer.fastconfig.settings.stepper_x.position_endstop|float %}
	{% set dual_carriage_position_max = printer.fastconfig.settings.dual_carriage.position_max|float %}
	{% set dual_carriage_position_endstop = printer.fastconfig.settings.dual_carriage.position_endstop|float %}
	{% set x_parking_space = parking_position_t0 - (stepper_x_position_endstop , stepper_x_position_min)|max %}
	{% set dc_parking_space = (dual_carriage_position_endstop , dual_carriage_position_max)|min - parking_position_t1 %}
	{% if svv.idex_xoffset|abs >= (x_parking_space - 0.5) or svv.idex_xoffset|abs >= (dc_parking_space - 0.5) %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Toolhead x-offset is too high for the available parking space. Calibrate your X and DC endstop positions and make sure you stay below 1mm." % (copy_mode_max_width)) }
	{% endif %}
	{% endif %}
	
	
	{% if (idex_mode == "copy" or idex_mode == "mirror") and printer.fastconfig.settings.ratos.enable_gcode_transform %}
	
	{% if params.MIN_X is not defined or params.MAX_X is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Something went wrong! Missing important post processor start print parameter!") }
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE=0
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	
	{% set boundary_box_min_x = params.MIN_X|default(0)|float %}
	{% set boundary_box_max_x = params.MAX_X|default(printable_x_max)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if default_toolhead == 0 %}
	
	{% set boundary_box_max_x = boundary_box_max_x + svv.idex_xoffset %}
	{% else %}
	
	{% set boundary_box_min_x = boundary_box_min_x - svv.idex_xoffset %}
	{% endif %}
	
	{% set center_x = printable_x_max / 2.0 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set object_width = boundary_box_max_x - boundary_box_min_x %}
	{% set copy_mode_max_width = center_x %}
	{% set mirror_mode_max_width = center_x - safe_distance / 2.0 %}
	
	DEBUG_ECHO PREFIX="START_PRINT" MSG="OBJECT_WIDTH: {object_width} BOUNDARY_BOX_MIN_X: {boundary_box_min_x} BOUNDARY_BOX_MAX_X: {boundary_box_max_x} CENTER_X: {center_x} SAFE_DISTANCE: {safe_distance}"
	
	
	{% if idex_mode == "copy" and object_width > copy_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for copy mode! Max supported width is %s mm" % (copy_mode_max_width)) }
	{% endif %}
	{% if idex_mode == "mirror" and object_width > mirror_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for mirror mode! Max supported width is %s mm" % (mirror_mode_max_width)) }
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = (printable_x_max - boundary_box_max_x - boundary_box_min_x) / 2 %}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE={object_xoffset}
	{% endif %}
	
	{% endif %}
	
	
	{% set has_initial_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_toolhead_filament_sensor %}
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% set has_initial_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_bowden_filament_sensor %}
	
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% if printer["dual_carriage"] is defined and both_toolheads %}
	
	{% set has_secondary_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set has_secondary_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_CHAMBER_FILTER_ON AT="before_print_start"
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true' %}
	{% if both_toolheads %}
	RATOS_ECHO MSG="Spool join is not possible if both toolheads are in use!"
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	{% endif %}
	
	
	CLEAR_PAUSE
	{% if printer["gcode_macro RatOS"].force_absolute_position|lower == 'true' %}
	G90
	{% endif %}
	SAVE_GCODE_STATE NAME=start_print_state
	
	
	G21
	
	G90
	
	M82
	_USER_START_PRINT_BEFORE_HOMING { rawparams }
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_BEGIN_BATCH
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_Z_HOP
	
	
	{% if idex_mode != '' and not (printer.fastconfig.settings.beacon is defined and (beacon_contact_start_print_true_zero or beacon_adaptive_heat_soak)) %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	{% if chamber_temp > 0 %}
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED={printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float}
	{% endif %}
	{% endif %}
	_CHAMBER_HEATER_ON START_CHAMBER_TEMP={start_chamber_temp} CHAMBER_TEMP={chamber_temp}
	_USER_START_PRINT_HEAT_CHAMBER { rawparams } CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_START_PRINT_BEFORE_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	RATOS_ECHO MSG="Heating bed..."
	
	M190 S{bed_temp}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_adaptive_heat_soak %}
	_MOVE_TO_SAFE_Z_HOME
	
	G1 Z2.5 F{z_speed}
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK LAYER_QUALITY={beacon_adaptive_heat_soak_layer_quality} MAXIMUM_FIRST_LAYER_DURATION={beacon_adaptive_heat_soak_maximum_first_layer_duration} MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={beacon_adaptive_heat_soak_max_wait}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_BED { rawparams }
	
	
	_START_PRINT_AFTER_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	_USER_START_PRINT_BED_MESH { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_BED_MESH X0={X0} X1={X1} Y0={Y0} Y1={Y1} T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_END_BATCH
	{% endif %}
	
	
	{% if idex_mode == '' %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[initial_tool]|float}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[0]|float}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={extruder_first_layer_temp[1]|float}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_PARK { rawparams }
	
	
	_START_PRINT_PARK
	
	
	RATOS_ECHO MSG="Heating Extruder..."
	{% if idex_mode == '' %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[initial_tool]|float}  MAXIMUM={extruder_first_layer_temp[initial_tool]|float + 5}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[0]|float}  MAXIMUM={extruder_first_layer_temp[0]|float + 5}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder1" MINIMUM={extruder_first_layer_temp[1]|float}  MAXIMUM={extruder_first_layer_temp[1]|float + 5}
	{% endif %}
	{% endif %}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	{% if idex_mode == '' %}
	_LED_PRINTING
	{% else %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	_LED_PRINTING
	{% else %}
	{% if both_toolheads %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	{% if toolchange_standby_temp > -1 %}
	_LED_TOOLHEAD_STANDBY TOOLHEAD={0 if initial_tool == 1 else 1}
	{% else %}
	_LED_PRINTING TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% else %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_EXTRUDER { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_AFTER_HEATING_EXTRUDER X0={X0} X1={X1} Y0={Y0} Y1={Y1} INITIAL_TOOLHEAD={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if idex_mode != '' %}
	{% if not both_toolheads %}
	{% if initial_tool != default_toolhead %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if idex_mode != '' %}
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=standby VALUE=False
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=standby VALUE=False
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if initial_tool == 1 else 'extruder1'} TARGET={toolchange_standby_temp}
	SET_GCODE_VARIABLE MACRO=T{0 if initial_tool == 1 else 1} VARIABLE=standby VALUE=True
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=start_print_state
	
	{% if printer["dual_carriage"] is defined %}
	_SET_IDEX_MODE_OFFSET
	{% endif %}
	
	
	{% if idex_mode != '' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% if idex_mode == "copy" and idex_mode != act_idex_mode %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == "mirror" and idex_mode != act_idex_mode %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={object_xoffset} MOVE=0
	{% endif %}
	{% else %}
	_SELECT_TOOL T={initial_tool} TOOLSHIFT=false
	_SET_TOOLHEAD_OFFSET
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	_SET_EXTRUSION_MODE
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={printer["print_stats"].print_duration}
	{% endif %}
	
	
	_USER_END_START_PRINT { rawparams }
	
	G92 E0
	
	
	_CHAMBER_FILTER_ON AT="after_print_start"
	
	_ALERT_NON_ZERO_Z_OFFSET
	
	RATOS_ECHO MSG="Printing..."

[gcode_macro _START_PRINT_BEFORE_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set is_stowable_probe = true if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' else false %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Pre-heating extruder..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={min_temp}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET={min_temp}
	{% endif %}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	{% endif %}
	{% endif %}
	
	
	{% if not is_stowable_probe %}
	{% if printer["dual_carriage"] is defined and act_t != default_toolhead %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	{% endif %}
	RATOS_ECHO MSG="Heat soaking z probe..."
	_MOVE_TO_SAFE_Z_HOME
	
	G0 Z2 F{z_speed}
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Waiting for extruder to be preheated..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	{% if default_toolhead == 0 %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_Z_HOP
	{% endif %}
	
	
	{% if auto_z_offset_calibration %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	PARK_TOOLHEAD
	_CLEANING_MOVE TOOLHEAD={default_toolhead} AUTOMATED=True
	_SELECT_TOOL T={0 if default_toolhead == 1 else 1} X={parking_position_t0 if default_toolhead == 1 else parking_position_t1} Y=0 TOOLSHIFT=false
	_CLEANING_MOVE TOOLHEAD={0 if default_toolhead == 1 else 1} AUTOMATED=True
	_VAOC_CALIBRATE_Z_OFFSET AUTO_Z_OFFSET=True
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=false
	{% endif %}
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	{% if needs_rehoming %}
	G28 Z
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	_START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE
	{% endif %}
	{% endif %}
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	PROBE PROBE_METHOD=contact SAMPLES=1

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	{% set fuzzy_radius = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_radius|default(0)|float if beacon_contact_start_print_true_zero_fuzzy_position else 0 %}
	
	{% set contact_true_zero_temp_has_been_set = False %}
	
	
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	
	
	
	{% if printer.beacon.last_probe_result|lower == "ok" %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	RATOS_ECHO MSG="Auto calibration nozzle wipe with probe result {last_z_offset}..."
	G0 Z{(0.2 + last_z_offset)} F{z_speed}
	G0 X70 F300
	{% else %}
	RATOS_ECHO MSG="Skipping auto calibration nozzle wipe because probing failed!"
	{% endif %}
	{% elif beacon_contact_wipe_before_true_zero_method == "probe_clean" %}
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	
	{% set contact_true_zero_temp_has_been_set = True %}
	
	
	
	
	
	
	
	
	BEACON_PROBE_CLEAN X=50 Y=10
	{% else %}
	CONSOLE_ECHO TYPE="error" TITLE="Unknown wipe method" MSG="Unknown wipe method '{beacon_contact_wipe_before_true_zero_method}' configured, skipping wipe before beacon true zero."
	{% endif %}
	{% endif %}
	
	
	G0 Z5 F{z_speed}
	_MOVE_TO_SAFE_Z_HOME FUZZY_RADIUS={fuzzy_radius}
	
	
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION
	
	{% if not contact_true_zero_temp_has_been_set %}
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon contact auto calibration..."
	
	{% if beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	
	G0 Z5 F{z_speed}

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION]
gcode = 
	{% set pos = printer.ratos.last_move_to_safe_z_home_position %}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE={pos[0]}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE={pos[1]}

[gcode_macro _START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set first_x = printer["gcode_macro START_PRINT"].first_x|default(-1)|float %}
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2.0 %}
	{% set center_y = printable_y_max / 2.0 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% if printer["dual_carriage"] is defined %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% endif %}
	
	
	{% set X0 = params.X0|default(-1)|int %}
	{% set X1 = params.X1|default(-1)|int %}
	{% set Y0 = params.Y0|default(-1)|int %}
	{% set Y1 = params.Y1|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	
	{% if idex_mode == '' %}
	
	_PRIME
	{% else %}
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	RATOS_ECHO PREFIX="IDEX" MSG="using combined prime offset for IDEX {idex_mode} mode"
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	{% if both_toolheads %}
	{% if initial_toolhead == 0 %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T{initial_toolhead}"
	_SELECT_TOOL T={initial_toolhead} TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	SET_MACRO_TRAVEL_SETTINGS
	
	{% if (X0 > -1 and Y1 > -1) or (first_x > 0 and first_y > 0) %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	{% endif %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	{% set first_z = 1 %}
	{% else %}
	{% set first_z = 3 %}
	{% endif %}
	
	
	{% if idex_mode == "mirror" %}
	{% if first_y >= 0 %}
	G0 Y{first_y} F{speed}
	{% else %}
	G0 Y{Y1} F{speed}
	{% endif %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={initial_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={initial_toolhead} E={printer["gcode_macro RatOS"].toolchange_first_purge|default(50)|float}
	_CLEANING_MOVE TOOLHEAD={initial_toolhead} AUTOMATED=True
	{% endif %}
	{% if first_x >= 0 and first_y >= 0 %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% else %}
	{% set first_x = X0 %}
	{% set first_y = Y0 %}
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'min' %}
	{% set first_x = X0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'max' %}
	{% set first_x = X1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|float <= center_x %}
	{% set first_x = X0 %}
	{% else %}
	{% set first_x = X1 %}
	{% endif %}
	{% endif %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'min' %}
	{% set first_y = Y0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'max' %}
	{% set first_y = Y1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|float <= center_y %}
	{% set first_y = Y0 %}
	{% else %}
	{% set first_y = Y1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	
	
	_LOAD_RATOS_SKEW_PROFILE

[gcode_macro _PRIME]
gcode = 
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	PRIME_BLOB INITIAL_TOOLHEAD={params.INITIAL_TOOLHEAD} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={params.IDEX_MODE} Y1={params.Y1}
	{% else %}
	
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif params.IDEX_MODE == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro END_PRINT]
description = End print procedure, use this in your Slicer.
gcode = 
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SAVE_GCODE_STATE NAME=end_print_state
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = printer["gcode_macro START_PRINT"].object_xoffset|default(0)|float %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(0-object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={(0-object_xoffset)}
	{% endif %}
	{% endif %}
	
	
	_USER_END_PRINT_BEFORE_HEATERS_OFF { rawparams }
	_END_PRINT_BEFORE_HEATERS_OFF
	TURN_OFF_HEATERS
	_USER_END_PRINT_AFTER_HEATERS_OFF { rawparams }
	_END_PRINT_AFTER_HEATERS_OFF
	_USER_END_PRINT_PARK { rawparams }
	_END_PRINT_PARK
	
	
	{% if printer["gcode_macro RatOS"].skew_profile is defined %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined and printer["gcode_macro RatOS"].end_print_motors_off|lower != 'false' %}
	
	M84
	{% endif %}
	
	
	M107
	
	
	BED_MESH_CLEAR
	RATOS_ECHO MSG="Done :)"
	
	
	RESTORE_GCODE_STATE NAME=end_print_state
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	M84
	{% endif %}
	
	
	RESET_NAMED_OFFSET EVENT="end_print"
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_CHAMBER_FILTER_ON AT="print_end"
	_CHAMBER_FILTER_OFF
	
	
	_CHAMBER_HEATER_OFF
	
	_USER_END_PRINT_FINISHED { rawparams }

[gcode_macro _END_PRINT_BEFORE_HEATERS_OFF]
gcode = 
	RATOS_ECHO MSG="Cleaning up..."

[gcode_macro _END_PRINT_AFTER_HEATERS_OFF]
gcode = 
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% set z_hop = printer["gcode_macro RatOS"].end_print_park_z_hop|float %}
	{% set r = printer["gcode_macro RatOS"].end_print_retract_filament|default(4)|float %}
	{% if current_z < (max_z - z_hop) %}
	{% set z_safe = z_hop %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G91
	
	{% if can_extrude %}
	G1 E-2 F3600
	{% endif %}
	
	G0 Z{z_safe} F3600
	
	{% if can_extrude %}
	G1 E-{(r-2)} F3600
	{% endif %}
	
	G90

[gcode_macro _SET_EXTRUSION_MODE]
gcode = 
	
	{% if printer["gcode_macro RatOS"].relative_extrusion|lower == 'true' %}
	M83
	{% else %}
	M82
	{% endif %}

[gcode_macro GENERATE_SHAPER_GRAPHS]
description = Genarates input shaper resonances graphs for analysis. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	{% set hz_per_sec = params.HZ_PER_SEC|default(1)|float %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set copy_mode_offset = printable_x_max / 4.0 %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	_IDEX_SINGLE
	{% endif %}
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	
	
	{% if idex_mode != 'copy' and idex_mode != 'mirror' %}
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	{% endif %}
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Shaper graph"

[gcode_shell_command generate_shaper_graph_x]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-x.sh
timeout = 60.
verbose = True

[gcode_shell_command generate_shaper_graph_y]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-y.sh
timeout = 60.
verbose = True

[gcode_macro MEASURE_COREXY_BELT_TENSION]
description = Generates resonance graph used to ensure belts are equally tensioned. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	_IDEX_SINGLE
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if measure_t1 == false or measure_t0 == false %}
	{action_raise_error("Axis specified. Not supported for belt tension on Y.")}
	{% else %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	G4 P5000
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	PARK_TOOLHEAD
	{% endif %}
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	G1 X{parking_position_t1} F{speed}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	
	
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Belt Tension Graph"

[gcode_shell_command generate_belt_tension_graph]
command = /home/pi/printer_data/config/RatOS/scripts/generate-belt-tension-graph.sh
timeout = 90.
verbose = True

[idle_timeout]
gcode = 
	{% if printer.webhooks.state|lower == 'ready' %}
	{% if printer.pause_resume.is_paused|lower == 'false' %}
	_USER_BEFORE_IDLE_TIMEOUT
	RATOS_ECHO PREFIX="IDLE" MSG="2 hours since last activity. Powering off heaters and motors.."
	TURN_OFF_HEATERS
	M84
	_USER_AFTER_IDLE_TIMEOUT
	{% endif %}
	{% endif %}
timeout = 7200

[temperature_sensor raspberry_pi]
sensor_type = temperature_host

[skew_correction]

[named_offsets]

[input_shaper]

[virtual_sdcard]
path = ~/printer_data/gcodes

[display_status]

[pause_resume]

[force_move]
enable_force_move = True

[respond]

[resonance_generator]

[ratos]
allow_unknown_gcode_generator = True
enable_gcode_transform = True

[exclude_object]

[bed_mesh]
split_delta_z = 0.001
horizontal_move_z = 2
mesh_min = 20,20
mesh_max = 480,480
probe_count = 40,40
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = .2
speed = 600
log_points = False

[fastconfig]

[heater_bed]
heater_pin = heater_bed_heating_pin
sensor_pin = heater_bed_sensor_pin
sensor_type = Generic 3950
min_temp = 0
max_temp = 140
pwm_cycle_time = 0.103
control = pid
pid_kp = 61.987
pid_ki = 1.781
pid_kd = 539.289

[printer]
kinematics = ratos_hybrid_corexy
max_velocity = 800
max_accel = 10000
minimum_cruise_ratio = 0.5
max_z_velocity = 50
max_z_accel = 600
square_corner_velocity = 5

[ratos_hybrid_corexy]
inverted = true

[dual_carriage]
axis = x
safe_distance = 55
position_max = 559.6
position_endstop = 559.6
position_min = 0
step_pin = PF9
dir_pin = dual_carriage_dir_pin
enable_pin = !PG2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t1:PA2

[gcode_macro _SET_IDEX_MODE_OFFSET]
description = "Internal use only. Sets the 'idex_mode' named offset that the active idex mode requires."
gcode = 
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_SET_IDEX_MODE_OFFSET" MSG="idex_mode: {idex_mode}, center_x: {center_x}"
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	SET_NAMED_OFFSET NAME=idex_mode X={(-center_x / 2)}
	{% else %}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% else %}
	{action_raise_error("_SET_IDEX_MODE_OFFSET: Printer not homed")}
	{% endif %}

[gcode_macro IDEX_SINGLE]
gcode = 
	_IDEX_REMAP_TOOLHEADS ENABLE=False
	_IDEX_SINGLE

[gcode_macro _IDEX_SINGLE]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_single"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set init = params.INIT|default(0)|int %}
	{% set new_x = params.X|default(-1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_default_t = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="init: {init}, new_x: {new_x}, idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, act_t: {act_t}"
	
	{% if idex_mode == "copy" or idex_mode == "mirror" or init == 1 %}
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="reset idex_mode offset"
	G1 X{center_x} F{(speed)}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="activate default carriage"
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolheads"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	G90
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position."
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1}
	G1 X{parking_position_default_t} F{speed}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move default toolhead to its new position."
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% if new_x == -1 %}
	{% set new_x = center_x %}
	{% endif %}
	G1 X{new_x} F{speed}
	
	M400
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="X Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set extruder motion queue."
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if default_toolhead==0 else default_toolhead}
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolhead offset."
	_SET_TOOLHEAD_OFFSET
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set input shaper."
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[default_toolhead]|float)} SHAPER_FREQ_Y={(shaper_y_freq[default_toolhead]|float)} SHAPER_TYPE_X={(shaper_x_type[default_toolhead]|lower)} SHAPER_TYPE_Y={(shaper_y_type[default_toolhead]|lower)}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="update Frontend."
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if default_toolhead==0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if default_toolhead==1 else False}
	{% else %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_single"

[gcode_macro IDEX_COPY]
gcode = 
	_IDEX_COPY

[gcode_macro _IDEX_COPY]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_copy"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set y = params.Y|default(-1)|int %}
	{% set dance = params.DANCE|default(1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_COPY" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}, y: {y}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "copy" %}
	{% if idex_mode == "mirror" %}
	{% if y>=0 %}
	G1 X{center_x} Y{y} F{(speed)}
	{% else %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	
	
	{% if idex_mode != "mirror" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance == 1 %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[2]|float)} SHAPER_FREQ_Y={(shaper_y_freq[2]|float)} SHAPER_TYPE_X={(shaper_x_type[2]|lower)} SHAPER_TYPE_Y={(shaper_y_type[2]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_copy"

[gcode_macro IDEX_MIRROR]
gcode = 
	_IDEX_MIRROR

[gcode_macro _IDEX_MIRROR]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_mirror"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set dance = params.DANCE|default(1)|int %}
	{% set priming = params.PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_MIRROR" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "mirror" %}
	
	{% if idex_mode == "copy" %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS MIRROR_PRIMING={params.PRIMING}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=MIRROR
	
	
	{% if idex_mode != "copy" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance and not priming %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[3]|float)} SHAPER_FREQ_Y={(shaper_y_freq[3]|float)} SHAPER_TYPE_X={(shaper_x_type[3]|lower)} SHAPER_TYPE_Y={(shaper_y_type[3]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_mirror"

[gcode_macro _IDEX_SET_TOOLHEADS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set mirror_priming = params.MIRROR_PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position_inactive_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_IDEX_SET_TOOLHEADS" MSG="idex_mode: {idex_mode}, act_t: {act_t}, center_x: {center_x}, mirror_priming: {mirror_priming}"
	
	
	{% if act_t != default_toolhead %}
	_SET_TOOLHEAD_OFFSET FORCE_TOOLHEAD={default_toolhead} MOVE=1
	{% endif %}
	
	{% if mirror_priming %}
	
	
	
	{% if parking_position_t0|abs < parking_position_t1 - printable_x_max %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{printable_x_max + parking_position_t0|abs} F{(speed)}
	{% else %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{0 - (parking_position_t1 - printable_x_max)} F{(speed)}
	{% endif %}
	
	{% else %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1} MODE=PRIMARY
	G1 X{parking_position_inactive_t} F{(speed)}
	
	
	{% if act_t==1 %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{center_x / 2} F{(speed)}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"

[gcode_macro IDEX_PARK]
gcode = 
	
	PARK_TOOLHEAD

[gcode_macro PARK_TOOLHEAD]
gcode = 
	
	{% set idex_mode = 'none' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="PARK_TOOLHEAD" MSG="Parking T{act_t}.."
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set parking_position_inact_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set printable_y_min = printer["gcode_macro RatOS"].printable_y_min|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" and 'xy' in printer.toolhead.homed_axes %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% elif printer.toolhead.position.y|float < printable_y_min %}
	G1 Y{printable_y_min} F{speed}
	{% endif %}
	
	SAVE_GCODE_STATE NAME=_PARK_TOOLHEAD
	G90
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0.5
	
	
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_inact_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	
	SET_VELOCITY_LIMIT ACCEL={printer.toolhead.max_accel} MINIMUM_CRUISE_RATIO=0.5
	M400
	RESTORE_GCODE_STATE NAME=_PARK_TOOLHEAD
	
	{% endif %}

[gcode_macro JOIN_SPOOLS]
gcode = 
	
	{% set spools = params.SPOOLS|default("") %}
	
	{% if spools == "" %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% else %}
	{% if spools != "0,1" and spools != "1,0" %}
	RATOS_ECHO MSG="Wrong spool configuration!"
	RATOS_ECHO MSG="Join Spools = JOIN_SPOOLS SPOOLS=0,1"
	RATOS_ECHO MSG="Deactivate = JOIN_SPOOLS SPOOLS="
	{% else %}
	{% if spools == "0,1" or spools == "1,0" %}
	_IDEX_JOIN_SPOOLS ENABLE=true
	{% else %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_JOIN_SPOOLS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if enable %}
	{% set has_t0_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t1_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t0_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined else false %}
	{% set has_t1_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined else false %}
	{% if (has_t0_toolhead_filament_sensor and has_t1_toolhead_filament_sensor) or (has_t0_bowden_filament_sensor and has_t1_bowden_filament_sensor) %}
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=True
	RATOS_ECHO MSG="Spool joining enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Can not enable spool joining! No filament sensors found."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining deactivated!"
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining is not possible in copy and mirror mode!"
	{% endif %}

[gcode_macro _JOIN_SPOOL]
gcode = 
	
	{% set old_toolhead = params.TOOLHEAD|int %}
	{% set new_toolhead = 0 if old_toolhead == 1 else 1 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set purge_after_load = printer["gcode_macro T%s" % new_toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_JOIN_SPOOL" MSG="toolhead: {new_toolhead}"
	
	{% set has_filament = true %}
	{% set has_new_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% set has_new_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% if has_new_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	{% if has_new_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	
	{% if has_filament %}
	RATOS_ECHO MSG="Joining spools! Please wait for extruder to heat up...."
	
	
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={new_toolhead}
	
	
	_DEACTIVATE_TOOLHEAD TOOLHEAD={old_toolhead}
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set extruder_temp = extruder_first_layer_temp[new_toolhead]|float %}
	{% else %}
	{% set extruder_temp = extruder_other_layer_temp[new_toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if new_toolhead == 0 else 'extruder1'} TARGET={extruder_temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if new_toolhead == 0 else 'extruder1'} MINIMUM={extruder_temp}  MAXIMUM={extruder_temp + 5}
	
	
	{% if purge_after_load > 0 %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_toolhead == 0 else new_toolhead}
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={new_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={new_toolhead} E={purge_after_load}
	_CLEANING_MOVE TOOLHEAD={new_toolhead} AUTOMATED=True
	
	
	SET_DUAL_CARRIAGE CARRIAGE={old_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if old_toolhead == 0 else old_toolhead}
	
	{% endif %}
	
	
	RESUME TOOLHEAD={new_toolhead}
	
	
	_IDEX_JOIN_SPOOLS ENABLE=false
	
	{% else %}
	{ action_raise_error("Spool join failed! No filament found or filament sensor is disabled.") }
	{% endif %}

[gcode_macro REMAP_TOOLHEADS]
gcode = 
	
	{% set toolheads = params.TOOLHEADS|default("") %}
	
	{% if toolheads == "" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% else %}
	{% if toolheads != "0,1" and toolheads != "1,0" %}
	RATOS_ECHO MSG="Wrong toolhead configuration!"
	RATOS_ECHO MSG="Remap = REMAP_TOOLHEADS TOOLHEADS=0,1"
	RATOS_ECHO MSG="Deactivate = REMAP_TOOLHEADS TOOLHEADS="
	{% else %}
	{% if toolheads == "0,1" or toolheads == "1,0" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=true
	_IDEX_SINGLE
	{% else %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_REMAP_TOOLHEADS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	{% if not enable or (idex_mode != "copy" and idex_mode != "mirror") %}
	{% if enable %}
	RATOS_ECHO MSG="Toolhead remapping enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping deactivated!"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE={enable}
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping not possible in copy and mirror mode!"
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	{% endif %}

[gcode_macro SHAPER_CALIBRATE]
rename_existing = SHAPER_CALIBRATE_ORG
gcode = 
	RATOS_ECHO PREFIX="IDEX" MSG="SHAPER_CALIBRATE is useless on IDEX machines. Please use the GENERATE_SHAPER_GRAPHS macro and type the values into `variable_shaper_*_freq` and `variable_shaper_*_type manually`."

[gcode_shell_command generate_shaper_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-shaper-graph.sh
timeout = 120.
verbose = True

[gcode_shell_command generate_tension_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-belt-tension-graph.sh
timeout = 120.
verbose = True

[gcode_macro SET_PRESSURE_ADVANCE]
variable_snyc_toolheads = False
rename_existing = SET_PRESSURE_ADVANCE_BASE
gcode = 
	{% if params.SYNC_TOOLHEADS is defined %}
	{% set snyc_toolheads = true if params.SYNC_TOOLHEADS|default(false)|lower == 'true' else false %}
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=True
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="Syncing toolheads..."
	{% else %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' or snyc_toolheads %}
	{% set advance = params.ADVANCE|default(printer['extruder'].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['extruder'].smooth_time|float)|float %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T0"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T1"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder1' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% else %}
	{% set extruder = 'extruder' if act_t == 0 else 'extruder1' %}
	{% if params.EXTRUDER is defined %}
	{% set extruder = params.EXTRUDER %}
	{% endif %}
	{% if extruder == 'extruder' or extruder == 'extruder1' %}
	{% set advance = params.ADVANCE|default(printer['%s' % extruder].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['%s' % extruder].smooth_time|float)|float %}
	SET_PRESSURE_ADVANCE_BASE EXTRUDER={extruder} ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% if params.EXTRUDER is not defined %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG={"T%s" % act_t}
	{% endif %}
	{% else %}
	SET_PRESSURE_ADVANCE_BASE { rawparams }
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro M106]
rename_existing = M106.1
variable_swap_speed = -1
gcode = 
	
	{% set s = [[params.S|default(255)|int, 255]|min, 0]|max %}
	{% set p = params.P|default(-1)|int %}
	{% set speed = s / 255 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set t = 1 if idex_mode=='primary' else 0 %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(0)|int == 1 else false %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set sync_fans = true %}
	{% endif %}
	
	
	{% if sync_fans and idex_mode != "copy" and idex_mode != "mirror" %}
	
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int %}
	
	
	{% if toolshift_count > total_toolshifts %}
	{% set sync_fans = false %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE=-1
	
	
	{% if p == -1 %}
	
	{% if speed == 0 %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed}
	{% else %}
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE={speed}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={(speed if (t == 0 or sync_fans) else 0)}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={(speed if (t == 1 or sync_fans) else 0)}
	{% endif %}
	{% else %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed if t == p else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed if t == p else 0}
	{% endif %}
	
	
	M106.1 S{s}

[gcode_macro M107]
rename_existing = M107.1
gcode = 
	{% set p = params.P|default(-1)|int %}
	M106 S0 P{p}

[gcode_macro _SELECT_TOOL]
variable_last_timestamp = 0
gcode = 
	{% if params.T is defined %}
	{% set idex_mode = '' %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if "xyz" not in printer.toolhead.homed_axes and (idex_mode == "copy" or idex_mode == "mirror") %}
	_IDEX_SINGLE
	{% set idex_mode = 'reset' %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set new_t = params.T|int %}
	
	
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads and is_printing_gcode %}
	{% set new_t = 0 if new_t == 1 else 1 %}
	{% endif %}
	
	
	{% set toolchange_prepurging_timer = printer["gcode_macro RatOS"].toolchange_prepurging_timer|default(0)|int %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	DEBUG_ECHO PREFIX="_SELECT_TOOL" MSG="act_t: {act_t}, new_t: {new_t}, is_printing_gcode: {is_printing_gcode}, swap_toolheads: {swap_toolheads}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	{% set act_extruder = 'extruder%s' % ('' if new_t == 0 else new_t) %}
	{% if new_t != act_t or printer.toolhead.extruder != act_extruder or idex_mode == 'reset' %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Selecting T{new_t}.."
	
	
	M220 S100
	
	
	
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(1)|int == 1 else false %}
	
	
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set toolshift = false %}
	{% endif %}
	
	
	{% set fan_speed = printer["fan_generic part_fan_t%s" % act_t].speed %}
	
	
	{% set deactivate_toolhead = false %}
	{% if is_printing_gcode %}
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int + 1 %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE={toolshift_count}
	{% if toolshift_count == total_toolshifts %}
	{% set deactivate_toolhead = true %}
	{% endif %}
	{% endif %}
	
	
	{% set needs_wakeup = true if printer["gcode_macro T%s" % new_t].standby|default(false)|lower == 'true' else false %}
	
	
	{% set needs_purging = false %}
	{% set wake_up_purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% if is_printing_gcode and toolchange_prepurging_timer > 0 and wake_up_purge > 0 %}
	{% set new_timestamp = printer["print_stats"].print_duration %}
	{% set elapsed_time = new_timestamp - last_timestamp %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={new_timestamp}
	{% if elapsed_time > toolchange_prepurging_timer %}
	{% set needs_purging = true %}
	{% endif %}
	{% endif %}
	
	
	{% set first_use_purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% if toolshift_count == 1 and first_use_purge > 0 %}
	{% set needs_purging = true %}
	{% endif %}
	
	
	{% if is_printing_gcode and (toolchange_standby_temp > -1 or needs_purging or needs_wakeup) %}
	_TOOLHEAD_STANDBY TOOLHEAD={act_t}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	_TOOLHEAD_WAKEUP TOOLHEAD={new_t} X={new_x} Y={new_y} Z={new_z} FAN_SPEED={fan_speed} TOOLSHIFT_COUNT={toolshift_count}
	{% else %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(false)|lower == 'true' else false %}
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if (new_t == 0 or sync_fans) else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if (new_t == 1 or sync_fans) else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	_TOOLCHANGE T={new_t} X={new_x} Y={new_y} Z={new_z} PARK_T0={park_t0} PARK_T1={park_t1} TOOLSHIFT={toolshift}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[new_t]|float)} SHAPER_FREQ_Y={(shaper_y_freq[new_t]|float)} SHAPER_TYPE_X={(shaper_x_type[new_t]|lower)} SHAPER_TYPE_Y={(shaper_y_type[new_t]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if new_t == 0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if new_t == 1 else False}
	
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% set sanity_check_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if new_t == 0 %}
	{% if printer.toolhead.extruder == 'extruder' %}
	{% if sanity_check_idex_mode == 'primary' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% elif new_t == 1 %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% if sanity_check_idex_mode == 'inactive' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _TOOLHEAD_STANDBY]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Putting toolhead T{toolhead} into standby mode."
	DEBUG_ECHO PREFIX="_TOOLHEAD_STANDBY" MSG="toolhead: {toolhead}, config_z_hop: {config_z_hop}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={toolhead} SYNC=0
	PARK_TOOLHEAD
	
	
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={toolchange_standby_temp}
	{% endif %}
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=True
	{% endif %}
	
	
	_LED_TOOLHEAD_STANDBY TOOLHEAD={toolhead}

[gcode_macro _TOOLHEAD_WAKEUP]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set fan_speed = params.FAN_SPEED|float %}
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift_count = params.TOOLSHIFT_COUNT|default(0)|int %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% if toolshift_count == 1 %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% endif %}
	{% set needs_wakeup = true if printer["gcode_macro T%s" % toolhead].standby|default(false)|lower == 'true' else false %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Waking up toolhead T{toolhead}. Please wait for extruder to heat up..."
	DEBUG_ECHO PREFIX="_TOOLHEAD_WAKEUP" MSG="toolhead: {toolhead}, fan_speed: {fan_speed}, new_x: {new_x}, new_y: {new_y}, new_z: {new_z}, config_z_hop: {config_z_hop}"
	
	
	_LED_TOOLHEAD_WAKEUP TOOLHEAD={toolhead}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={toolhead} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE=1
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if toolhead == 0 else toolhead}
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if needs_wakeup %}
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set temp = extruder_first_layer_temp[toolhead]|float %}
	{% else %}
	{% set temp = extruder_other_layer_temp[toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if toolhead == 0 else 'extruder1'} MINIMUM={temp}  MAXIMUM={temp + 5}
	{% endif %}
	
	
	_LED_PRINTING TOOLHEAD={toolhead}
	
	
	{% if purge > 0 %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={toolhead} E={purge}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	
	
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if toolhead == 1 else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	G92 E0
	G1 E-{e} F{feedrate}
	G92 E0
	
	
	{% if new_x >= 0 and new_y >= 0 %}
	G1 X{new_x} Y{new_y} F{speed}
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={config_z_hop} T={toolhead} SYNC=0
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=False

[gcode_macro _TOOLCHANGE]
variable_toolshift_count = 0
gcode = 
	
	
	{% set new_t = params.T|default(-1)|int %}
	{% set new_x = params.X|default(-1.0)|float %}
	{% set new_y = params.Y|default(-1.0)|float %}
	{% set new_z = params.Z|default(-1.0)|float %}
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(true)|lower == 'true' else false %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T: {new_t}, X: {new_x}, Y: {new_y}, Z: {new_z}, PARK_T0: {park_t0}, PARK_T1: {park_t1}, IS_PRINTING_GCODE: {is_printing_gcode}, TOOLSHIFT: {toolshift}"
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	{% if park_t0 >= 0 and park_t1 >= 0 %}
	{% set parking_position_t0 = park_t0 %}
	{% set parking_position_t1 = park_t1 %}
	{% set parking_position_act_t = park_t0 if act_t == 0 else park_t1 %}
	{% endif %}
	
	
	{% if not is_printing_gcode and not toolshift %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Changing tool to T{new_t} without retracting/extruding or moving the toolheads except for parking."
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	G90
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% if not is_printing_gcode and toolshift and new_x < 0 and new_y < 0 %}
	{% set new_x = center_x %}
	{% set new_y = printer.gcode_move.gcode_position.y|float %}
	{% endif %}
	
	{% if new_x < 0 or new_y < 0 %}
	
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="No new X or Y position given, parking the active toolhead and activating the new toolhead without moving it."
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={new_t}
	
	
	{% if "x" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	{% if is_printing_gcode %}
	_EXTRUDE T={new_t}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	{% if "xyz" not in printer.toolhead.homed_axes %}
	
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	
	
	{% set svv = printer.save_variables.variables %}
	{% if new_t == default_toolhead %}
	{% set new_xoffset = 0 %}
	{% set new_yoffset = 0 %}
	{% set new_zoffset = 0 %}
	{% else %}
	{% set new_xoffset = -svv.idex_xoffset %}
	{% set new_yoffset = -svv.idex_yoffset %}
	{% set new_zoffset = -svv.idex_zoffset %}
	{% endif %}
	
	{% set xoffset_correction = new_xoffset - printer.named_offsets.toolhead_alignment.x %}
	{% set yoffset_correction = new_yoffset - printer.named_offsets.toolhead_alignment.y %}
	{% set zoffset_correction = new_zoffset - printer.named_offsets.toolhead_alignment.z %}
	
	{% if new_t == 0 %}
	
	{% set t0_act_x = parking_position_t0 %}
	{% set t1_act_x = printer.toolhead.position.x|float %}
	{% set t0_new_x = new_x %}
	{% set t1_new_x = parking_position_t1 %}
	{% set t0_distance = t0_new_x - t0_act_x %}
	{% set t1_distance = t1_new_x - t1_act_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T0."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	
	
	G1 X{t0_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x + (t1_new_x - t1_act_x)} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t0_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T0: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% elif new_t == 1 %}
	
	{% set t0_act_x = printer.toolhead.position.x|float %}
	{% set t1_act_x = parking_position_t1 %}
	{% set t0_new_x = parking_position_t0 %}
	{% set t1_new_x = new_x %}
	{% set t0_distance = t0_act_x - t0_new_x %}
	{% set t1_distance = t1_act_x - t1_new_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T1."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x - t1_distance + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t1_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T1: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% endif %}
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	{% endif %}

[gcode_macro _ZHOP_BEFORE_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_hop = params.Z_HOP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_HOP: {z_hop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="COMBINED_ZHOP G1 Z+{z_hop} E-{e} F{speed * 60}"
	G1 Z+{z_hop} E-{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="ZHOP G1 Z+{z_hop} F{speed * 60}"
	G1 Z+{z_hop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="RETRACT G1 E-{e} F{feedrate}"
	G1 E-{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _ZDROP_AFTER_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_drop = params.Z_DROP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_DROP: {z_drop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="COMBINED_ZDROP G1 Z-{z_drop} E{e} F{speed * 60}"
	G1 Z-{z_drop} E{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="ZDROP G1 Z-{z_drop} F{speed * 60}"
	G1 Z-{z_drop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="EXTRUDE G1 E{e} F{feedrate}"
	G1 E{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _EXTRUDE]
gcode = 
	
	{% set t = params.T|int %}
	
	
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	
	DEBUG_ECHO PREFIX="_EXTRUDE" MSG="G1 E{e} F{feedrate * 60}"
	
	
	G91
	M82
	G92 E0
	G1 E{e} F{feedrate * 60}
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _DEACTIVATE_TOOLHEAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_DEACTIVATE_TOOLHEAD" MSG="TOOLHEAD {toolhead}"
	
	
	{% if toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% endif %}
	
	
	M106.1 S0
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={toolhead}

[delayed_gcode _INIT_TOOLHEADS]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	_IDEX_SINGLE INIT=1
	
	
	{% if printer.fastconfig.settings.dual_carriage.safe_distance is defined %}
	{% if printer.fastconfig.settings.dual_carriage.safe_distance|float < 50 %}
	{ action_emergency_stop("Dual carriage safe_distance seems to be too low!") }
	{% endif %}
	{% else %}
	{ action_emergency_stop("Dual carriage safe_distance not defined!") }
	{% endif %}

[gcode_macro _SET_TOOLHEAD_OFFSET]
description = "Internal use only. Sets the toolhead_alignment offset (and hotend_thermal_expansion offset when configured) for the active/dominant toolhead."
gcode = 
	
	{% set move = params.MOVE|default(0)|int %}
	{% set force_toolhead = params.FORCE_TOOLHEAD|default(-1)|int %}
	
	
	{% if params.T is defined %}
	CONSOLE_ECHO TYPE="error" MSG="_SET_TOOLHEAD_OFFSET called with deprectated T parameter, which is ignored."
	{';$_SET_TOOLHEAD_OFFSET_ignoring_TOOLHEAD_parameter'}
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="active/dominant toolhead: {toolhead}, MOVE: {move}, FORCE_TOOLHEAD: {force_toolhead}"
	
	
	{% if force_toolhead >= 0 %}
	{% set toolhead = force_toolhead %}
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="FORCE_TOOLHEAD applied, using TOOLHEAD: {toolhead}"
	{% endif %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set move = 0 %}
	{% endif %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|int %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X=0 Y=0 MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z=0 MOVE={move} SPEED={z_speed}
	{% else %}
	{% set svv = printer.save_variables.variables %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X={(-svv.idex_xoffset)} Y={(-svv.idex_yoffset)} MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-svv.idex_zoffset)} MOVE={move} SPEED={z_speed}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}

[gcode_macro TOOLSHIFT_CONFIG]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={params.SPEED|default(300)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={params.ACCEL|default(5000)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_retraction VALUE={params.RETRACT|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_extrusion VALUE={params.EXTRUDE|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_feedrate VALUE={params.FEEDRATE|default(7200)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={params.Z_HOP|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zspeed VALUE={params.Z_SPEED|default(25)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_combined_zhop VALUE={true if params.COMBINED_ZHOP|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_sync_fans VALUE={true if params.SYNC_FANS|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_prepurging_timer VALUE={params.AUTO_PURGE_TIME|default(0)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_purge VALUE={params.PURGE|default(25)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_standby_temp VALUE={params.STANDBY_TEMP|default(-1)|float}

[gcode_macro CALCULATE_DC_ENDSTOP]
description = "DEPRECATED: This macro has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."
gcode = 
	CONSOLE_ECHO TITLE="CALCULATE_DC_ENDSTOP has been deprecated" TYPE="error" MSG="The CALCULATE_DC_ENDSTOP has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."

[gcode_macro _VAOC]
variable_is_fixed = True
variable_is_started = False
variable_is_started_at_temp = False
variable_additional_safe_distance = 50
variable_safe_z = 30
variable_auto_z_offset_calibration = True
variable_enable_camera_cooling = True
variable_camera_cooling_fan_speed = 0.3
variable_camera_cooling_temperature = 50
variable_toolchange_travel_speed = 300
variable_toolchange_travel_accel = 5000
variable_adjusting_secondary_toolhead_focus_adjusts_zoffset = False
variable_cache_toolchange_travel_speed = 300
variable_cache_toolchange_travel_accel = 5000
variable_cache_toolchange_zhop = 1.0
variable_t0_toolhead_sensor_enabled = 0
variable_t1_toolhead_sensor_enabled = 0
variable_t0_bowden_sensor_enabled = 0
variable_t1_bowden_sensor_enabled = 0
variable_loaded_skew_profile = ""
variable_gcode_z_offset = 0.0
variable_start_x_offset = 0.0
variable_start_y_offset = 0.0
gcode = 
	_ECHO_VAOC_VARS
variable_expected_camera_x_position = 212.5
variable_expected_camera_y_position = 530.5

[gcode_macro _VAOC_START]
description = Called from the front end. If T0_TEMP, T1_TEMP and BED_TEMP parameter are specified, VAOC calibration will start under real conditions at printing temp.
gcode = 
	
	{% set t0_temp = params.T0_TEMP|default(0)|int %}
	{% set t1_temp = params.T1_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(0)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro SKEW_PROFILE"].loaded_profile|default("") %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=loaded_skew_profile VALUE='"{loaded_skew_profile}"'
	
	
	{% if t0_temp > 0 and t1_temp > 0 and bed_temp > 0 %}
	
	
	{% if not is_fixed %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("VAOC calibration at temp works only with a fixed installed VAOC device.") }
	{% endif %}
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE=0
	{% endif %}
	
	
	START_PRINT EXTRUDER_TEMP={t0_temp},{t1_temp} EXTRUDER_OTHER_LAYER_TEMP={t0_temp},{t1_temp} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp} INITIAL_TOOL=0 TOTAL_LAYER_COUNT=1 X0={(printable_x_max / 2 - 10)} Y0={(printable_y_max / 2 - 10)} X1={(printable_x_max / 2 + 10)} Y1={(printable_y_max / 2 + 10)} TOTAL_TOOLSHIFTS=1 FIRST_X={printable_x_max / 2} FIRST_Y={printable_y_max / 2} MIN_X={(printable_x_max / 2 - 10)} MAX_X={(printable_x_max / 2 + 10)} USED_TOOLS=0,1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=True
	
	{% endif %}
	
	
	_START_VAOC

[gcode_macro _START_VAOC]
description = Called from _VAOC_START. Do not call it manually.
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(printable_x_max/2)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(printable_y_max/2)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	DEBUG_ECHO PREFIX="VAOC_START" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, zcontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_x_offset VALUE={svv.idex_xoffset|default(0.0)|float}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_y_offset VALUE={svv.idex_yoffset|default(0.0)|float}
	
	
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_SAFE_Z_HEIGHT
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_speed VALUE={printer["gcode_macro RatOS"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_accel VALUE={printer["gcode_macro RatOS"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_zhop VALUE={printer["gcode_macro RatOS"].toolchange_zhop|float}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE=0
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"START X_REFERENCE:%.6f Y_REFERENCE:%.6f Z_REFERENCE:%.6f PARK_T0:%.6f PARK_T1:%.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, parking_position_t0, parking_position_t1)}
	
	
	_LED_VAOC_ON
	
	
	
	
	
	
	
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=gcode_z_offset VALUE={printer.gcode_move.homing_origin.z}
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z=0
	
	
	MAYBE_HOME
	M400
	
	
	_LOAD_RATOS_SKEW_PROFILE
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	IDEX_SINGLE
	{% endif %}
	
	
	
	SAVE_GCODE_STATE NAME=vaoc_state
	
	
	RESET_NAMED_OFFSET EVENT=reset_all
	
	
	{% if is_fixed %}
	_SELECT_TOOL T=0 TOOLSHIFT=false
	{% if default_toolhead == 0 %}
	G1 X{idex_xcontrolpoint} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint + safe_distance + additional_safe_distance} F{speed}
	{% else %}
	G1 X{idex_xcontrolpoint - safe_distance - additional_safe_distance} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint} F{speed}
	{% endif %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	{% else %}
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	G1 X{idex_xcontrolpoint} F{speed}
	G1 Y{idex_ycontrolpoint} F{speed}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	
	
	_SELECT_TOOL T={default_toolhead} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	{% if not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={default_toolhead}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=True

[gcode_macro _VAOC_END]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_y = printable_y_max / 2 %}
	{% set saved_gcode_z_offset = printer["gcode_macro _VAOC"].gcode_z_offset|default(0.0)|float %}
	
	DEBUG_ECHO PREFIX="_VAOC_END" MSG="printable_y_max: {printable_y_max}, center_y: {center_y}, safe_z: {safe_z}"
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% set x_offset_change = svv.idex_xoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_x_offset|default(0.0)|float %}
	{% set y_offset_change = svv.idex_yoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_y_offset|default(0.0)|float %}
	{% set offset_change_norm = (x_offset_change ** 2 + y_offset_change ** 2) ** 0.5 %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="VAOC calibration changed the relative XY offset between T0 and T1 by {offset_change_norm|round(3)} mm (ΔX: {x_offset_change|round(3)}, ΔY: {y_offset_change|round(3)})"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	G1 Y{center_y} F{speed}
	
	
	_IDEX_SINGLE INIT=1
	
	
	_LED_VAOC_OFF
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={printer["gcode_macro _VAOC"].cache_toolchange_zhop|float}
	
	
	{% if printer["gcode_macro _VAOC"].is_started_at_temp|default(true)|lower == 'true' %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_bowden_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_bowden_sensor_enabled|int}
	{% endif %}
	{% endif %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro _VAOC"].loaded_skew_profile|default("") %}
	{% if loaded_skew_profile != "" %}
	SKEW_PROFILE LOAD={loaded_skew_profile}
	{% else %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=vaoc_state
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z={saved_gcode_z_offset}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False

[gcode_macro _VAOC_LOAD_TOOL]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set auto_temp_offset = true if params.AUTO_TEMP_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set toolhead_zoffset = svv.idex_zoffset|default(0)|float %}
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move T%s to control point: X%.6f Y%.6f Z%.6f IS_FIXED=%s"' % (t, idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, is_fixed)}
	
	
	{% if not auto_temp_offset and not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={t}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	{% set current_z = printer.toolhead.position.z|float %}
	{% set lowest_toolhead_z = [current_z, current_z - toolhead_zoffset]|min %}
	{% if lowest_toolhead_z < safe_z %}
	G1 Z{[safe_z, safe_z + toolhead_zoffset]|max} F{z_speed}
	{% else %}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	{% endif %}
	
	
	_SELECT_TOOL T={t} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_SET_CAMERA_COOLING]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	
	
	{% set enable_camera_cooling = true if printer["gcode_macro _VAOC"].enable_camera_cooling|default(true)|lower == 'true' else false %}
	{% set camera_cooling_temperature = printer["gcode_macro _VAOC"].camera_cooling_temperature|float %}
	{% set camera_cooling_fan_speed = printer["gcode_macro _VAOC"].camera_cooling_fan_speed|float %}
	
	
	{% if printer.heater_bed.temperature >= camera_cooling_temperature and enable_camera_cooling %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={camera_cooling_fan_speed if t == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={camera_cooling_fan_speed if t == 1 else 0}
	
	
	M106.1 S{camera_cooling_fan_speed}
	
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	{% endif %}

[gcode_macro _VAOC_SET_TOOL]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="_VAOC_SET_TOOL" MSG="IDEX_MODE: {idex_mode}, TOOLHEAD: {toolhead}"
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	{% set x = printer.gcode_move.gcode_position.x|float %}
	{% set y = printer.gcode_move.gcode_position.y|float %}
	{% set z = printer.gcode_move.gcode_position.z|float %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE={x}
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE={y}
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE={z}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Control point was set: X%.6f Y%.6f Z%.6f"' % (x, y, z)}
	
	{% else %}
	
	
	
	{% set move_diff_x = printer.gcode_move.gcode_position.x|float - svv.idex_xcontrolpoint|float %}
	{% set move_diff_y = printer.gcode_move.gcode_position.y|float - svv.idex_ycontrolpoint|float %}
	{% set move_diff_z = printer.gcode_move.gcode_position.z|float - svv.idex_zcontrolpoint|float %}
	
	
	{% set new_x_offset = svv.idex_xoffset - move_diff_x %}
	{% set new_y_offset = svv.idex_yoffset - move_diff_y %}
	{% set new_z_offset = svv.idex_zoffset - move_diff_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE={new_x_offset}
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE={new_y_offset}
	
	{% set z_focus_msg = "" %}
	{% if move_diff_z|abs > 1e-6 %}
	{% if printer["gcode_macro _VAOC"].adjusting_secondary_toolhead_focus_adjusts_zoffset|default(false)|lower == 'true' %}
	{% set z_focus_msg = " (Z offset adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={new_z_offset}
	{% else %}
	{% set z_focus_msg = " (Z offset not adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	{% set new_z_offset = svv.idex_zoffset %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset was set: X%.6f Y%.6f Z%.6f%s"' % (toolhead, new_x_offset, new_y_offset, new_z_offset, z_focus_msg)}
	
	{% endif %}

[gcode_macro _VAOC_MOVE]
gcode = 
	
	{% set x = params.X|default(0)|float %}
	{% set y = params.Y|default(0)|float %}
	{% set z = params.Z|default(0)|float %}
	
	
	G91
	{% if z != 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 Z%.6f F300"' % (z)}
	G1 Z{z} F300
	
	{% else %}
	{% if x <=2 and y <=2 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 X%.6f Y%.6f F18000"' % (x, y)}
	G1 X{x} Y{y} F18000
	{% endif %}
	{% endif %}
	G90

[gcode_macro _VAOC_CALIBRATE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	{% if printer["z_offset_probe"] is defined and is_started %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	
	{% if auto_z_offset %}
	_START_VAOC AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_END
	{% else %}
	_VAOC_LOAD_TOOL T={default_toolhead}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	{% endif %}
	
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_Z_OFFSET
	
	{% endif %}

[gcode_macro _VAOC_PROBE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}
	{% if not auto_z_offset %}
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	{% endif %}
	M400
	_VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT

[gcode_macro _VAOC_Z_OFFSET_PROBE_CURRENT_POSITION]
gcode = 
	
	Z_OFFSET_PROBE PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_DROP=1 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median

[gcode_macro _VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT]
gcode = 
	{% if printer["z_offset_probe"] is defined %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE={last_z}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Z-offset control point set:: %.6f"' % last_z}
	
	{% else %}
	
	
	
	{% set z = svv.idex_zoffsetcontrolpoint|float - last_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={z}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-z)}
	
	
	G0 Z{svv.idex_zcontrolpoint|float} F{z_speed}
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset set: Z %.6f"' % (t, z)}
	
	{% endif %}
	
	{% endif %}

[gcode_macro _VAOC_ECHO_Z_OFFSET]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s toolhead z-offset %.6f"' % (1 if default_toolhead == 0 else 0, svv.idex_zoffset)}
	{% if svv.idex_zoffset|abs < 0.02 %}
	CONSOLE_ECHO TITLE={'"Perfect toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="You have a perfect toolhead z-offset!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.02 and svv.idex_zoffset|abs < 0.05 %}
	CONSOLE_ECHO TITLE={'"Good toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is good!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.05 and svv.idex_zoffset|abs < 0.1 %}
	CONSOLE_ECHO TITLE={'"High toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset could be better._N_Use minimum 0.3mm first layer height for copy and mirror mode prints." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.1 and svv.idex_zoffset|abs < 0.2 %}
	CONSOLE_ECHO TITLE={'"Bad toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is bad._N_Copy and mirror mode prints are not recommended with it." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.2 %}
	CONSOLE_ECHO TITLE={'"Unacceptable toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is unacceptable._N_Do not print in copy and mirror mode with it." TYPE="alert"
	{% endif %}
	RATOS_ECHO PREFIX="VAOC" MSG="Toolhead z-offset calibration done!"

[gcode_macro _VAOC_CALIBRATE_TEMP_OFFSET]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if is_fixed and is_started and printer["z_offset_probe"] is defined and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	_VAOC_LOAD_TOOL T={default_toolhead} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_NOZZLE_TEMP_OFFSETS
	
	{% endif %}

[gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET=0
	
	
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	M400

[gcode_macro _VAOC_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(150)|float %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Probing with nozzle temperature {temp}°C..."
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	
	
	G0 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _VAOC_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set msg = '"T0 expansion coefficient %.6fmm_N_T1 expansion coefficient %.6fmm"' % (svv.nozzle_expansion_coefficient_t0, svv.nozzle_expansion_coefficient_t1) %}
	CONSOLE_ECHO TITLE="Nozzle expansion coefficients:" MSG={msg} TYPE="success"

[gcode_macro _VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - expected_camera_x_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC x-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_xcontrolpoint, expected_camera_x_position)) }
	{% endif %}
	{% if (idex_ycontrolpoint - expected_camera_y_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC y-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_ycontrolpoint, expected_camera_y_position)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - printer.gcode_move.gcode_position.x|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected y-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_xcontrolpoint, printer.gcode_move.gcode_position.x|float)) }
	{% endif %}
	{% if (idex_ycontrolpoint - printer.gcode_move.gcode_position.y|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected x-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_ycontrolpoint, printer.gcode_move.gcode_position.y|float)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_SAFE_Z_HEIGHT]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set idex_zoffsetcontrolpoint = svv.idex_zoffsetcontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_SAFE_Z_HEIGHT" MSG={'"idex_zcontrolpoint: %.6f, idex_zoffsetcontrolpoint: %.6f"' % (idex_zcontrolpoint, idex_zoffsetcontrolpoint)}
	
	{% if safe_z < idex_zcontrolpoint + 2 or safe_z < idex_zoffsetcontrolpoint + 2 %}
	{action_raise_error("VAOC safe_z value (%.3f) is too low, it must be higher than %.3f" % (safe_z, [idex_zoffsetcontrolpoint + 2, idex_zcontrolpoint + 2]|max))}
	{% endif %}

[gcode_macro _VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED]
gcode = 
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T0. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T1. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_RESET]
gcode = 
	DEBUG_ECHO PREFIX="_VAOC_RESET" MSG="running template-emitted _VAOC_RESET macro"
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE=212.5
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE=530.5
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE=10
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE=0
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE=0.0
	
	RESET_DC_ENDSTOP_CONFIGURATION
	RESET_Y_MAX_ADJUSTMENT
	
	
	CONSOLE_ECHO TITLE="VAOC Configuration Reset" MSG="VAOC configuration has been reset. You must RESTART klipper for the changes to take effect,_N_then re-calibrate VAOC."

[gcode_macro _ECHO_VAOC_VARS]
description = Echo VAOC variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro _VAOC"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro _VAOC_SWITCH_LED]
gcode = 
	{% if params.STATE|default(0)|int == 1 %}
	_LED_VAOC_ON
	{% else %}
	_LED_VAOC_OFF
	{% endif %}

[gcode_macro Z_PROBE_TEST_T0]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T0
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST_T1]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T1
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	
	
	_VAOC_Z_PROBE_TEST_EVALUATE
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro _VAOC_Z_PROBE_LOOP]
gcode = 
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_SHAKE_IT
	_VAOC_START

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if primary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T0. Retried {primary_retries} time(s)."
	{% endif %}
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	
	{% if (primary_range - secondary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 is drifting significantly more than T1."
	{% endif %}
	{% if (secondary_range - primary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 is drifting significantly more than T0."
	{% endif %}
	
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T0]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T1]
gcode = 
	
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _SHAKE_IT]
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	_Z_HOP
	{% for i in range(3) %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 + 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 + 1}
	{% endfor %}
	{% for i in range(2) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 + 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 + 50}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 1}
	{% endfor %}
	{% endfor %}

[gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 retries updated: {new_retries}"

[gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 retries updated: {new_retries}"

[gcode_macro _CLEAR_PRIMARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _CLEAR_SECONDARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _VAOC_TEST_Z_OFFSET]
gcode = 
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}

[delayed_gcode _IDEX_INIT]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	VERIFY_HYBRID_INVERTED

[gcode_macro Z_TILT_ADJUST]
rename_existing = Z_TILT_ADJUST_ORIG
gcode = 
	
	{% set beacon_contact_z_tilt_adjust_samples = printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust_samples|default(2)|int %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(true)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	_IDEX_SINGLE
	
	_SELECT_TOOL T={printer["gcode_macro RatOS"].default_toolhead|default(0)|int} TOOLSHIFT=false
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_tilt_adjust %}
	Z_TILT_ADJUST_ORIG PROBE_METHOD=contact SAMPLES={beacon_contact_z_tilt_adjust_samples}
	{% else %}
	Z_TILT_ADJUST_ORIG
	{% endif %}
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if idex_mode == "copy" %}
	_IDEX_COPY
	{% elif idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[stepper_x]
position_max = 500
position_endstop = -59.6
position_min = -59.6
step_pin = PF13
dir_pin = x_dir_pin
enable_pin = !PF14
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t0:PA2

[stepper_y]
position_max = 533.65
position_min = -14.35
position_endstop = -14.35
step_pin = PG0
dir_pin = !y_dir_pin
enable_pin = !PF15
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = PG9

[stepper_z]
position_max = 500
position_min = -7
step_pin = PC13
dir_pin = !z0_dir_pin
enable_pin = !PF1
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4
homing_speed = 10
endstop_pin = probe:z_virtual_endstop

[z_tilt]
z_positions = 
	0,0
	250,500
	500,0
points = 
	20, 10
	480, 230
	20, 450
horizontal_move_z = 20
retries = 10
retry_tolerance = 0.02
speed = 600

[extruder]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t0:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t0:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t0:PD3
dir_pin = toolboard_t0:e_dir_pin
enable_pin = !toolboard_t0:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[firmware_retraction]
retract_speed = 60
unretract_extra_length = 0
unretract_speed = 60
retract_length = 0.2

[extruder1]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t1:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t1:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t1:PD3
dir_pin = toolboard_t1:e_dir_pin
enable_pin = !toolboard_t1:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[resonance_tester]
accel_chip_x = lis2dw toolboard_t0
accel_chip_y = lis2dw toolboard_t0
probe_points = 
	250,250,20

[tmc5160 stepper_x]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC4
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 dual_carriage]
stealthchop_threshold = 0
interpolate = True
cs_pin = PF2
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y]
stealthchop_threshold = 0
interpolate = True
cs_pin = PD11
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y1]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC7
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[stepper_y1]
step_pin = PG4
dir_pin = y1_dir_pin
enable_pin = !PA2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46

[tmc2209 stepper_z]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE4
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[tmc2209 stepper_z1]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE1
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z1]
step_pin = PE2
dir_pin = !z1_dir_pin
enable_pin = !PD4
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 stepper_z2]
stealthchop_threshold = 0
interpolate = True
uart_pin = PD3
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z2]
step_pin = PE6
dir_pin = !z2_dir_pin
enable_pin = !PE0
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 extruder]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t0:PB3
run_current = 0.707
sense_resistor = 0.11

[tmc2209 extruder1]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t1:PB3
run_current = 0.707
sense_resistor = 0.11

[beacon]
serial = /dev/beacon
x_offset = 0
y_offset = 27.5
mesh_main_direction = x
mesh_runs = 1
mesh_cluster_size = 0
speed = 15.
lift_speed = 80.
contact_max_hotend_temperature = 275
contact_mesh_min = 20,20
contact_mesh_max = 480,480

[beacon_user_z_offset]

[beacon_mesh]

[beacon_true_zero_correction]

[beacon_adaptive_heat_soak]

[delayed_gcode _BEACON_INIT]
initial_duration = 1
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	_BEACON_MESH_INIT
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_coefficient_multiplier
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_applied_offset
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=beacon_saved_runtime_offset
	{% if printer["gcode_macro RatOS"].beacon_contact_expansion_multiplier is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_contact_expansion_multiplier is no longer used, please remove it from your config file."
	{% endif %}
	{% if printer["gcode_macro RatOS"].beacon_scan_compensation_resolution is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_scan_compensation_resolution is no longer used, please remove it from your config file."
	{% endif %}

[gcode_macro BEACON_RATOS_CALIBRATION]
gcode = 
	RATOS_ECHO MSG="Did you mean BEACON_RATOS_CALIBRATE?"

[gcode_macro BEACON_RATOS_CALIBRATE]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	BEACON_INITIAL_CALIBRATION _AUTOMATED=True
	
	{% if beacon_contact_start_print_true_zero %}
	BEACON_POKE_TEST _AUTOMATED=True
	_BEACON_CHECK_POKE
	{% if printer["dual_carriage"] is not defined %}
	BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET _AUTOMATED=True
	{% endif %}
	{% endif %}
	
	{% set already_heated = False %}
	
	
	{% if beacon_contact_start_print_true_zero and beacon_scan_compensation_enable %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% set already_heated = True %}
	{% endif %}
	
	
	BEACON_FINAL_CALIBRATION _AUTOMATED=True _AUTOMATED_ALREADY_HEATED={already_heated} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	{% if beacon_contact_start_print_true_zero %}
	{% if printer["dual_carriage"] is not defined %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	_BEACON_ECHO_POKE
	{% endif %}
	RATOS_ECHO MSG="Beacon calibration finished!"
	
	
	_LED_BEACON_CALIBRATION_END
	
	
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG

[gcode_macro BEACON_INITIAL_CALIBRATION]
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Initial beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro BEACON_FINAL_CALIBRATION]
description = Runs BEACON_AUTO_CALIBRATE after heating the bed and chamber to specified temperatures. This creates a beacon model under reference conditions for future use.
	This macro will skip calibration if both the beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero settings are enabled, because a new
	model will be calibrated automatically at the start of each print. Use FORCE=True to override this check.
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set already_heated = true if params._AUTOMATED_ALREADY_HEATED|default(false)|lower == 'true' else false %}
	{% set force = params.FORCE|default('false')|lower in ('1', 'true', 'yes') %}
	
	
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default('false')|lower == "true" %}
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero and not force %}
	RATOS_ECHO MSG="BEACON_FINAL_CALIBRATION skipped, not needed because beacon_contact_calibrate_model_on_true_zero is enabled. Use FORCE=True to override."
	{% else %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	{% if chamber_temp > 0 and not already_heated %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	{% if not already_heated %}
	
	G0 Z2.5 F{z_hop_speed}
	
	
	RATOS_ECHO MSG="Waiting for calibration temperature..."
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	{% if beacon_adaptive_heat_soak %}
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,3600]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_Z_HOP
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Final beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	{% endif %}

[gcode_macro BEACON_POKE_TEST]
variable_poke_result_1 = -1
variable_poke_result_2 = -1
variable_poke_result_3 = -1
variable_poke_result_4 = -1
variable_poke_result_5 = -1
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_1 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_2 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_3 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_4 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_5 VALUE=-1
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G0 Z5 F{z_hop_speed}
	
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=1
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=2
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=3
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=4
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=5
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Beacon poke test finished!"
	{% if not automated %}
	_BEACON_ECHO_POKE
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro _BEACON_PROBE_POKE]
gcode = 
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	BEACON_POKE speed=3 top=5 bottom={poke_bottom}
	BEACON_QUERY

[gcode_macro _BEACON_STORE_POKE]
gcode = 
	
	{% set i = params.I|default(1)|int %}
	
	
	{% set last_z = printer.beacon.last_poke_result|default(0)|float %}
	
	
	{% if printer.beacon.last_poke_result|lower != "none" %}
	{% if printer.beacon.last_poke_result.error == 0 %}
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE={"poke_result_%s" % i} VALUE={printer.beacon.last_poke_result.latency}
	{% endif %}
	{% endif %}

[gcode_macro _BEACON_CHECK_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% if p1 == -1 or p2 == -1 or p3 == -1 or p4 == -1 or p5 == -1 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test error!") }
	{% endif %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	{% if avg > 6 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test failed!") }
	{% endif %}

[gcode_macro _BEACON_ECHO_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	
	
	{% if avg <= 1 %}
	{% set type = "success" %}
	{% set note = "Extremely low noise, rarely achieved" %}
	{% elif avg > 1 and avg <= 4 %}
	{% set type = "info" %}
	{% set note = "Excellent performance for a typical printer" %}
	{% elif avg > 4 and avg <= 8 %}
	{% set type = "warning" %}
	{% set note = "Acceptable performance, machine may have considerable cyclic axis noise" %}
	{% elif avg > 8 and avg <= 11 %}
	{% set type = "alert" %}
	{% set note = "Not ideal, may want to verify proper mounting or use thinner stackups" %}
	{% elif avg > 11 %}
	{% set type = "alert" %}
	{% set note = "Reason for concern, present setup may be risky to continue with" %}
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon poke test result:" TYPE={type} MSG={'"Average latency: %.2f_N_%s"' % (avg, note)}

[gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Nozzle temperature offset calibration..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET=0
	
	
	{% if not automated %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing with nozzle temperature {temp}°C..."
	PROBE PROBE_METHOD=contact PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median
	BEACON_QUERY
	
	
	G0 Z5 F{z_speed}

[gcode_macro _BEACON_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer.beacon.last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{default_toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% if default_toolhead == 0 %}
	CONSOLE_ECHO TYPE="info" MSG={'"T0 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t0}
	{% else %}
	CONSOLE_ECHO TYPE="info" MSG={'"T1 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t1}
	{% endif %}

[gcode_macro _BEACON_SET_NOZZLE_TEMP_OFFSET]
description = "Set the thermal expansion z offset for the active toolhead based on the current extruder target temperature and thermal expansion coefficient."
gcode = 
	{% if params.RESET is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The RESET parameter is no longer supported and has no effect."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% if params.TOOLHEAD is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The TOOLHEAD parameter is no longer supported and has no effect. The macro now automatically determines the current toolhead."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	{% if beacon_contact_expansion_compensation %}
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set nozzle_expansion_coefficient_t0 = svv.nozzle_expansion_coefficient_t0|default(0)|float %}
	{% if printer["dual_carriage"] is defined %}
	{% set nozzle_expansion_coefficient_t1 = svv.nozzle_expansion_coefficient_t1|default(0)|float %}
	{% endif %}
	
	
	{% set temp = printer['extruder' if toolhead == 0 else 'extruder1'].target|float %}
	
	
	{% set temp_delta = temp - beacon_contact_true_zero_temp %}
	{% set expansion_coefficient = nozzle_expansion_coefficient_t0 if toolhead == 0 else nozzle_expansion_coefficient_t1 %}
	{% set expansion_offset = temp_delta * (expansion_coefficient / 100) %}
	
	
	SET_NAMED_OFFSET NAME=hotend_thermal_expansion Z={expansion_offset} MOVE=1 MOVE_SPEED={z_speed}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG={'"Nozzle expansion offset of %.6fmm applied to T%s"' % (expansion_offset, toolhead)}
	DEBUG_ECHO PREFIX="_BEACON_SET_NOZZLE_TEMP_OFFSET" MSG="toolhead: {toolhead}, coefficient: {expansion_coefficient|round(6)}, temp_delta: {temp_delta|round(1)},  expansion_offset: {expansion_offset|round(6)}"
	
	{% endif %}

[gcode_macro BEACON_MEASURE_BEACON_OFFSET]
variable_needs_compensation = False
variable_reference_z = 0.0
variable_front = 0.0
variable_front_left = 0.0
variable_front_right = 0.0
variable_back = 0.0
variable_back_left = 0.0
variable_back_right = 0.0
variable_right = 0.0
variable_left = 0.0
variable_margin_x = 40
variable_margin_y = 40
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=False
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Measure beacon offset..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="center"
	
	
	G0 X{margin_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_left"
	
	
	G0 X{safe_home_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front"
	
	
	G0 X{(printable_x_max - margin_x)} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_right"
	
	
	G0 X{safe_home_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back"
	
	
	G0 X{margin_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_left"
	
	
	G0 X{margin_x} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="left"
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_BEACON_ECHO_BEACON_OFFSET
	
	
	_LED_BEACON_CALIBRATION_END
	
	{% endif %}

[gcode_macro _BEACON_STORE_BEACON_OFFSET]
gcode = 
	
	{% set location = params.LOCATION|lower %}
	
	
	{% set last_z = printer.beacon.last_offset_result["delta"]|default(0)|float %}
	
	
	{% if location == "center" %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE={location} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_BEACON_OFFSET]
gcode = 
	
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float * 1000 %}
	{% set front_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_left|default(0)|float * 1000 %}
	{% set front = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front|default(0)|float * 1000 %}
	{% set front_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_right|default(0)|float * 1000 %}
	{% set right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].right|default(0)|float * 1000 %}
	{% set back_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_right|default(0)|float * 1000 %}
	{% set back = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back|default(0)|float * 1000 %}
	{% set back_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_left|default(0)|float * 1000 %}
	{% set left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].left|default(0)|float * 1000 %}
	
	{% set line_1 = "Front left:    %.6fμm" % (front_left) %}
	{% set line_2 = "Front center:  %.6fμm" % (front) %}
	{% set line_3 = "Front right:   %.6fμm" % (front_right) %}
	{% set line_4 = "Left center:   %.6fμm" % (left) %}
	{% set line_5 = "Right center:  %.6fμm" % (right) %}
	{% set line_6 = "Back left:     %.6fμm" % (back_left) %}
	{% set line_7 = "Back center:   %.6fμm" % (back) %}
	{% set line_8 = "Back right:    %.6fμm" % (back_right) %}
	
	{% set max_value = [(front_left|abs), (front|abs), (front_right|abs), (left|abs), (right|abs), (back_left|abs), (back|abs), (back_right|abs)]|max %}
	{% if max_value <= 50 %}
	{% set type = "success" %}
	{% set recommendation = "Very low beacon offset: %.6fμm._N_No beacon scan compensation needed." % max_value %}
	{% elif max_value > 50 and max_value <= 100 %}
	{% set type = "info" %}
	{% set recommendation = "Low beacon offset: %.6fμm._N_You may experience first layer inconsistensies, consider beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 100 and max_value <= 150 %}
	{% set type = "warning" %}
	{% set recommendation = "High beacon offset: %.6fμm._N_High chance of first layer problems, beacon scan compensation is highly encouraged." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 150 and max_value <= 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Very High beacon offset: %.6fμm._N_You will encounter first layer problems on large prints unless you activate beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Extremely high beacon offset: %.6fμm._N_You have significant scan/contact inconsistency which is indicative of mechanical problems, please investigate before resorting to software compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon offset relative to the center" TYPE={type} MSG={'"_N_%s_N__N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s"' % (recommendation, line_1, line_2, line_3, line_4, line_5, line_6, line_7, line_8)}

[gcode_macro BEACON_CREATE_SCAN_COMPENSATION_MESH]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set profile = params.PROFILE|default("auto")|string %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set keep_temp_meshes = params.KEEP_TEMP_MESHES|default(0) %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' %}
	{% set desired_spacing = printer["gcode_macro RatOS"].beacon_scan_compensation_desired_spacing|float %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	
	{% if not beacon_scan_compensation_enable %}
	RATOS_ECHO MSG="Beacon scan compensation is disabled!"
	
	{% else %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	
	
	RATOS_ECHO MSG="Please wait..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	G1 Z2.5 F{z_speed}
	{% if beacon_adaptive_heat_soak %}
	
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,9000]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if not (beacon_adaptive_heat_soak or bed_heat_soak_time > 0) %}
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if printer.z_tilt is defined %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% endif %}
	{% if printer.quad_gantry_level is defined %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% endif %}
	
	
	_BEACON_CREATE_SCAN_COMPENSATION_MESH_CORE PROFILE="{profile}" DESIRED_SPACING={desired_spacing} CHAMBER_TEMP={chamber_temp} KEEP_TEMP_MESHES={keep_temp_meshes}
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	{% if automated %}
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon scan compensation mesh created!"
	
	
	{% if not automated %}
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED]
gcode = 
	
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED" MSG="beacon_scan_compensation_profile {beacon_scan_compensation_profile}, beacon_scan_compensation_enable {beacon_scan_compensation_enable}"
	
	{% if beacon_scan_compensation_enable %}
	BEACON_APPLY_SCAN_COMPENSATION PROFILE="{beacon_scan_compensation_profile}"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL]
gcode = 
	
	{% set beacon_contact_start_print_true_zero = params.BEACON_CONTACT_START_PRINT_TRUE_ZERO|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = params.beacon_contact_calibrate_model_on_true_zero|lower == 'true' %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and not printer.beacon.model %}
	{% set beacon_model_required_for_true_zero = beacon_contact_start_print_true_zero and not beacon_contact_calibrate_model_on_true_zero %}
	{% set beacon_model_required_for_homing =
	printer.fastconfig.settings.stepper_z.endstop_pin == 'probe:z_virtual_endstop'
	and (( printer.fastconfig.settings.beacon.home_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower != 'true')
	or ( printer.fastconfig.settings.beacon.default_probe_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower != 'true' )) %}
	{% if beacon_model_required_for_homing or beacon_model_required_for_true_zero %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("An active Beacon model is required. Have you performed initial Beacon calibration?") }
	{% endif %}
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION]
gcode = 
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set bed_temp_mismatch_is_error = true if printer["gcode_macro RatOS"].beacon_scan_compensation_bed_temp_mismatch_is_error|default(false)|lower == 'true' else false %}
	
	{% set bed_temp = params.BED_TEMP|default(0)|float %}
	{% if bed_temp == 0 %}
	{% set bed_temp = printer.heater_bed.temperature %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_PREFLIGHT_CHECK_BEACON" MSG="beacon_scan_compensation_profile={beacon_scan_compensation_profile}, beacon_scan_compensation_enable={beacon_scan_compensation_enable}, bed_temp={bed_temp}"
	
	{% if beacon_scan_compensation_enable %}
	_VALIDATE_COMPENSATION_MESH_PROFILE PROFILE="{beacon_scan_compensation_profile}" TITLE="Check Beacon scan compensation profile" SUBJECT="Configured compensation profile '{beacon_scan_compensation_profile}'" COMPARE_BED_TEMP={bed_temp} COMPARE_BED_TEMP_IS_ERROR={bed_temp_mismatch_is_error}
	{% endif %}

[gcode_macro _BEACON_MAYBE_SCAN_COMPENSATION]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set needs_scan_compensation = true if printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].needs_compensation|default(false)|lower == 'true' else false %}
	
	{% if needs_scan_compensation %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% endif %}

[gcode_macro _BEACON_HOME_AND_ABL]
gcode = 
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	{% if needs_rehoming %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}

[gcode_macro SAVE_Z_OFFSET]
description = Deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead, or in Mainsail use the SAVE button in the Z-OFFSET section.
gcode = 
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default('false')|lower == 'true' %}
	{% set msg = "SAVE_Z_OFFSET is deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead,_N_or in Mainsail use the SAVE button in the Z-OFFSET section."%}
	{% if not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% set msg = msg + "_N_You must then use the SAVE_CONFIG command to persist the change." %}
	{% endif %}
	CONSOLE_ECHO TYPE="error" MSG="{msg}"

[gcode_macro _BEACON_OFFSET_COMPARE]
gcode = 
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing..."
	
	
	BEACON_OFFSET_COMPARE SAMPLES_DROP=1 SAMPLES=3
	BEACON_QUERY

[fan]
pin = rpi:gpio4

[fan_generic part_fan_t0]
pin = PA8
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[fan_generic part_fan_t1]
pin = PE5
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[heater_fan toolhead_cooling_fan_t0]
heater = extruder
shutdown_speed = 1
pin = toolboard_t0:PB4

[heater_fan toolhead_cooling_fan_t1]
heater = extruder1
shutdown_speed = 1
pin = toolboard_t1:PB4

[controller_fan controller_fan]
pin = dinghy:PA4
tachometer_pin = dinghy:PC15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[z_offset_probe]
pin = ^PG10
z_offset = -7
y_offset = 0
x_offset = 37.5
speed = 10
samples = 3
sample_retract_dist = 5
lift_speed = 10.0
samples_result = median
samples_tolerance = 0.2
samples_tolerance_retries = 5

[neopixel vaoc_led]
pin = PB10
chain_count = 6
color_order = GRB

[heater_fan vaoc_fan]
pin = PD13
heater = heater_bed
fan_speed = 1.0
heater_temp = 50

[fan_generic filter]
pin = !PD14
enable_pin = PD15

[gcode_macro T0]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = True
variable_color = "7bff33"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = -32.6
variable_parking_position = -57.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=0 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[gcode_macro T1]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = False
variable_color = "0ea5e9"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = 532.6
variable_parking_position = 557.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=1 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[save_variables]
filename = /home/pi/printer_data/config/ratos-variables.cfg

[mcu dinghy]
serial = /dev/serial/by-id/usb-Klipper_stm32f072xb_Dragon_dinghy-if00

[temperature_sensor th0]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA0

[temperature_sensor th1]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA1

[temperature_sensor th2]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA2

[temperature_sensor th3]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA3

[controller_fan CTL2]
pin = dinghy:PB14
tachometer_pin = dinghy:PB15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[mcu plasma]
serial = /dev/serial/by-id/usb-Klipper_rp2040_Plasma-if00

[neopixel Chamber_Lights]
pin = plasma:gpio15
chain_count = 140
color_order = GRBW
initial_red = 0.0
initial_green = 0.0
initial_blue = 0.0
initial_white = 0.1

[beacon model default]
model_coef = 1.5287863993594841,
	1.9289099639750602,
	0.8838828622507556,
	0.25554883784260735,
	-0.015171504024913506,
	0.3044946127013882,
	0.15820427856566457,
	-0.25262403959326246,
	0.042488512846660914,
	0.16662470122520964
model_domain = 1.842634574664148e-07,1.9339206373083917e-07
model_range = 0.200000,5.000000
model_temp = 13.222247
model_offset = 0.00000

[bed_mesh default]
version = 1
points = 
	0.016163, 0.016713, 0.001923, -0.017658, -0.031574, -0.032498, -0.030898, -0.032177, -0.035213, -0.031148, -0.021322, -0.016924, -0.015012, -0.013911, -0.012197, -0.012583, -0.010489, -0.007529, -0.003986, -0.000980, 0.005518, 0.014442, 0.027426, 0.034677, 0.037410, 0.040391, 0.041842, 0.040369, 0.037615, 0.030776, 0.027664, 0.022856, 0.016892, 0.015398, 0.014717, 0.006921, 0.001532, 0.000731, 0.008657, 0.014036
	0.005356, -0.005066, -0.016998, -0.029668, -0.038334, -0.043672, -0.041139, -0.042488, -0.045199, -0.039432, -0.028746, -0.023642, -0.024058, -0.022802, -0.019679, -0.018514, -0.018102, -0.016476, -0.012722, -0.010077, -0.001809, 0.007180, 0.019853, 0.027754, 0.029964, 0.033626, 0.036783, 0.032018, 0.029372, 0.020847, 0.017634, 0.011926, 0.009013, 0.009254, 0.007972, -0.001380, -0.006940, -0.002160, 0.006135, 0.008330
	-0.004900, -0.006720, -0.021914, -0.039691, -0.050459, -0.050377, -0.046281, -0.048755, -0.054708, -0.051499, -0.033927, -0.027632, -0.030243, -0.031447, -0.024387, -0.021408, -0.020382, -0.018068, -0.015930, -0.013877, -0.006099, 0.003479, 0.013310, 0.024783, 0.025522, 0.030849, 0.033573, 0.031409, 0.025495, 0.016683, 0.011264, 0.008805, 0.006856, 0.008059, 0.007305, 0.002581, -0.003320, -0.003239, 0.004691, 0.010045
	-0.008791, -0.019334, -0.029149, -0.040533, -0.051698, -0.058235, -0.054863, -0.054840, -0.055692, -0.049534, -0.036731, -0.033053, -0.035667, -0.035315, -0.024352, -0.023825, -0.022538, -0.020438, -0.018207, -0.015389, -0.006515, 0.001966, 0.013591, 0.019434, 0.020600, 0.024967, 0.029425, 0.026812, 0.018980, 0.007878, 0.002360, 0.000859, 0.003849, 0.005649, 0.005421, -0.000416, -0.007906, -0.003164, 0.007582, 0.010039
	-0.018512, -0.018210, -0.033932, -0.050501, -0.061588, -0.064139, -0.060236, -0.062528, -0.067065, -0.062039, -0.045815, -0.039448, -0.040521, -0.042080, -0.033870, -0.030878, -0.027396, -0.024548, -0.021298, -0.020041, -0.011880, -0.002847, 0.008689, 0.015857, 0.015934, 0.018697, 0.022439, 0.022106, 0.017916, 0.005879, 0.001037, -0.001311, -0.001335, 0.001897, 0.003656, 0.000561, -0.006084, -0.005683, 0.000338, 0.006245
	-0.028558, -0.036721, -0.044680, -0.054969, -0.066140, -0.075045, -0.073515, -0.073161, -0.075696, -0.068963, -0.058892, -0.053111, -0.050990, -0.048040, -0.041262, -0.037419, -0.034866, -0.031845, -0.029787, -0.026524, -0.017896, -0.009322, -0.001010, 0.005819, 0.008058, 0.010456, 0.013266, 0.012529, 0.007992, -0.001491, -0.006769, -0.009303, -0.005980, -0.003567, -0.003340, -0.011496, -0.018818, -0.014808, -0.004181, -0.000733
	-0.037253, -0.038393, -0.053129, -0.066170, -0.075959, -0.079233, -0.077475, -0.082688, -0.086779, -0.083983, -0.069005, -0.062542, -0.060351, -0.058481, -0.051101, -0.043149, -0.039837, -0.037039, -0.034698, -0.031301, -0.024330, -0.019786, -0.010285, -0.001967, 0.002812, 0.004899, 0.009657, 0.006946, 0.002155, -0.005232, -0.009851, -0.011218, -0.011509, -0.010097, -0.010293, -0.013175, -0.018958, -0.019846, -0.012107, -0.005641
	-0.046584, -0.055590, -0.062606, -0.069218, -0.080399, -0.087414, -0.089037, -0.092376, -0.095115, -0.088957, -0.080802, -0.073290, -0.068741, -0.064591, -0.054452, -0.048270, -0.045916, -0.044559, -0.042047, -0.039605, -0.032667, -0.025789, -0.019495, -0.012773, -0.006697, -0.003025, 0.001413, 0.000817, -0.004738, -0.013008, -0.017605, -0.018191, -0.018524, -0.016356, -0.016750, -0.021992, -0.028943, -0.025791, -0.016146, -0.010447
	-0.051029, -0.051677, -0.068218, -0.079622, -0.088590, -0.089331, -0.089731, -0.096072, -0.105329, -0.100771, -0.087584, -0.079320, -0.075489, -0.072081, -0.064183, -0.054662, -0.048601, -0.049465, -0.047050, -0.045011, -0.040009, -0.032508, -0.025212, -0.018144, -0.011996, -0.008136, -0.003187, -0.003214, -0.006646, -0.013044, -0.019446, -0.020615, -0.022270, -0.021298, -0.020215, -0.020946, -0.026034, -0.026598, -0.021025, -0.012328
	-0.057184, -0.064908, -0.073093, -0.081584, -0.091971, -0.097048, -0.097688, -0.101869, -0.106651, -0.102162, -0.095658, -0.087938, -0.082718, -0.077017, -0.069608, -0.060682, -0.056889, -0.056864, -0.054260, -0.052011, -0.044563, -0.038927, -0.031943, -0.025832, -0.021170, -0.014319, -0.009046, -0.008543, -0.011751, -0.020287, -0.026608, -0.027259, -0.029120, -0.025549, -0.023221, -0.027725, -0.032477, -0.028427, -0.019343, -0.014932
	-0.060411, -0.062241, -0.080781, -0.090744, -0.100903, -0.099702, -0.098468, -0.104236, -0.116853, -0.112701, -0.102623, -0.095036, -0.091407, -0.089871, -0.079701, -0.070222, -0.064325, -0.063875, -0.062248, -0.059396, -0.052699, -0.047589, -0.041526, -0.028442, -0.024526, -0.019549, -0.015403, -0.014251, -0.017989, -0.022824, -0.027328, -0.029155, -0.033315, -0.032426, -0.027619, -0.030776, -0.033688, -0.032458, -0.027219, -0.019649
	-0.067541, -0.076514, -0.082321, -0.088656, -0.099968, -0.104930, -0.105875, -0.109051, -0.115531, -0.112996, -0.105760, -0.100390, -0.096171, -0.090011, -0.080050, -0.073632, -0.067451, -0.067031, -0.065225, -0.062471, -0.056370, -0.050129, -0.041626, -0.030801, -0.027579, -0.022472, -0.014826, -0.015306, -0.020316, -0.025953, -0.030661, -0.034103, -0.035502, -0.032738, -0.031311, -0.037314, -0.041306, -0.035280, -0.027449, -0.020395
	-0.068162, -0.069269, -0.088235, -0.096809, -0.103385, -0.103271, -0.102507, -0.109535, -0.123412, -0.118580, -0.106622, -0.099580, -0.097644, -0.096978, -0.087259, -0.077196, -0.068978, -0.067016, -0.063682, -0.062548, -0.057901, -0.052295, -0.044088, -0.032703, -0.026551, -0.021607, -0.014155, -0.013747, -0.017390, -0.022419, -0.027444, -0.030877, -0.033450, -0.032423, -0.032041, -0.033598, -0.035149, -0.034054, -0.029356, -0.020998
	-0.069473, -0.075924, -0.083569, -0.089648, -0.101235, -0.105828, -0.109144, -0.112613, -0.117233, -0.114186, -0.107090, -0.098616, -0.097084, -0.094257, -0.086773, -0.076409, -0.069532, -0.066472, -0.060956, -0.059191, -0.052886, -0.047752, -0.041275, -0.032437, -0.027780, -0.020398, -0.012061, -0.010133, -0.014056, -0.021528, -0.027924, -0.030605, -0.030609, -0.026068, -0.029346, -0.033991, -0.038254, -0.030610, -0.021109, -0.015885
	-0.068084, -0.066409, -0.083944, -0.094013, -0.102504, -0.105274, -0.106036, -0.112090, -0.121664, -0.117824, -0.104850, -0.097467, -0.098833, -0.098622, -0.089603, -0.078147, -0.068143, -0.066300, -0.061573, -0.057727, -0.054825, -0.048625, -0.040164, -0.030532, -0.025948, -0.020264, -0.014196, -0.010702, -0.013794, -0.019775, -0.026095, -0.028838, -0.030254, -0.027944, -0.027980, -0.030915, -0.032446, -0.028861, -0.023732, -0.014676
	-0.065280, -0.068669, -0.076948, -0.082397, -0.094986, -0.105117, -0.107099, -0.108954, -0.112557, -0.110326, -0.100725, -0.096325, -0.096240, -0.092388, -0.081185, -0.071682, -0.065650, -0.062250, -0.057027, -0.054691, -0.048349, -0.042069, -0.032712, -0.027728, -0.023396, -0.018458, -0.008357, -0.005699, -0.011447, -0.020033, -0.026387, -0.030280, -0.028443, -0.023735, -0.023838, -0.031580, -0.034204, -0.027768, -0.018029, -0.010628
	-0.061662, -0.057052, -0.075163, -0.086710, -0.094182, -0.097544, -0.098814, -0.105908, -0.114460, -0.111718, -0.097559, -0.091614, -0.093860, -0.093098, -0.081687, -0.069410, -0.064117, -0.062745, -0.055603, -0.051413, -0.048043, -0.040363, -0.031842, -0.023420, -0.017470, -0.012600, -0.008163, -0.003898, -0.007635, -0.013254, -0.019807, -0.025153, -0.027074, -0.023513, -0.023727, -0.028669, -0.029153, -0.024831, -0.018735, -0.009246
	-0.056176, -0.059439, -0.066501, -0.071527, -0.085216, -0.094918, -0.097595, -0.099419, -0.101847, -0.102015, -0.093849, -0.089867, -0.088840, -0.083167, -0.071832, -0.062522, -0.058023, -0.057771, -0.053050, -0.048285, -0.041374, -0.033527, -0.024473, -0.018428, -0.013958, -0.008161, -0.001196, 0.001754, -0.004016, -0.011132, -0.018325, -0.021813, -0.021514, -0.016948, -0.018061, -0.025702, -0.028671, -0.021470, -0.011028, -0.001934
	-0.059202, -0.050525, -0.065461, -0.076792, -0.084156, -0.088538, -0.090719, -0.096070, -0.105729, -0.105136, -0.090350, -0.083865, -0.087807, -0.086145, -0.074773, -0.064235, -0.057641, -0.055896, -0.051286, -0.046566, -0.042431, -0.034723, -0.023762, -0.014983, -0.009126, -0.004877, 0.000094, 0.003492, -0.000931, -0.005883, -0.011665, -0.015251, -0.016432, -0.016119, -0.015373, -0.018827, -0.019994, -0.017564, -0.012298, 0.002094
	-0.055561, -0.058184, -0.062669, -0.068111, -0.080741, -0.091895, -0.093911, -0.094387, -0.100239, -0.100695, -0.089841, -0.085682, -0.085212, -0.082910, -0.073072, -0.063594, -0.056157, -0.053482, -0.048107, -0.045405, -0.039982, -0.029777, -0.019905, -0.013872, -0.009732, -0.004272, 0.003500, 0.006909, 0.001302, -0.004626, -0.012374, -0.014751, -0.014637, -0.011794, -0.012913, -0.018244, -0.023377, -0.018086, -0.006575, 0.003294
	-0.062834, -0.047300, -0.060870, -0.073023, -0.079303, -0.082121, -0.083623, -0.091321, -0.100996, -0.098896, -0.085406, -0.078881, -0.081932, -0.082077, -0.074409, -0.063158, -0.053822, -0.050328, -0.045077, -0.039678, -0.035825, -0.028532, -0.017793, -0.009121, -0.003444, -0.000905, 0.003990, 0.007745, 0.004595, 0.000143, -0.004555, -0.007411, -0.010850, -0.010100, -0.010079, -0.013177, -0.016434, -0.014663, -0.010248, -0.000213
	-0.054748, -0.053907, -0.057576, -0.063118, -0.072478, -0.081366, -0.084424, -0.086348, -0.089718, -0.089305, -0.081771, -0.076889, -0.076923, -0.073518, -0.067973, -0.057643, -0.050848, -0.046966, -0.041560, -0.036436, -0.029233, -0.020685, -0.010240, -0.004935, -0.001084, 0.002478, 0.009168, 0.014038, 0.010885, 0.004752, -0.001650, -0.004209, -0.003998, -0.002336, -0.003784, -0.010930, -0.016480, -0.012798, -0.003650, 0.002998
	-0.059345, -0.041989, -0.057435, -0.068229, -0.072857, -0.072586, -0.075155, -0.083286, -0.091292, -0.089727, -0.073702, -0.068353, -0.072910, -0.073863, -0.065527, -0.053635, -0.046064, -0.043899, -0.037607, -0.031251, -0.026194, -0.018885, -0.008095, 0.000309, 0.004911, 0.007046, 0.010642, 0.015635, 0.015277, 0.012612, 0.008074, 0.004852, 0.001546, 0.000504, 0.000589, -0.002769, -0.006432, -0.007765, -0.005391, 0.006950
	-0.050324, -0.049088, -0.052417, -0.057257, -0.063818, -0.071057, -0.074636, -0.075459, -0.079445, -0.077368, -0.068788, -0.063940, -0.065040, -0.063419, -0.054864, -0.044910, -0.038774, -0.036951, -0.031149, -0.026080, -0.018383, -0.011985, -0.001732, 0.003893, 0.007180, 0.011120, 0.017429, 0.021738, 0.019167, 0.015812, 0.011027, 0.007243, 0.006720, 0.009346, 0.006598, -0.003776, -0.009199, -0.007592, 0.005481, 0.014396
	-0.058437, -0.035937, -0.050762, -0.060425, -0.061123, -0.059090, -0.062399, -0.072124, -0.080338, -0.074950, -0.060985, -0.054754, -0.059333, -0.060500, -0.051714, -0.038834, -0.031117, -0.031693, -0.025186, -0.017982, -0.014316, -0.010137, 0.000228, 0.008774, 0.014018, 0.016470, 0.019918, 0.022071, 0.021109, 0.019957, 0.018698, 0.015803, 0.013135, 0.011136, 0.008719, 0.003522, -0.000994, 0.000525, 0.006297, 0.018454
	-0.046143, -0.041577, -0.045391, -0.046668, -0.051722, -0.057607, -0.062802, -0.065205, -0.068243, -0.066293, -0.058216, -0.051324, -0.051806, -0.051018, -0.043393, -0.032431, -0.024016, -0.023321, -0.018504, -0.013897, -0.008455, -0.001123, 0.006609, 0.010462, 0.013887, 0.019328, 0.024804, 0.026590, 0.023420, 0.020337, 0.017129, 0.017199, 0.016391, 0.015616, 0.013257, 0.005832, -0.000019, 0.003462, 0.014308, 0.023624
	-0.051989, -0.030294, -0.043380, -0.051339, -0.050711, -0.048193, -0.052258, -0.061218, -0.070507, -0.068810, -0.049476, -0.042352, -0.046018, -0.046673, -0.038670, -0.027263, -0.018137, -0.018587, -0.013603, -0.008482, -0.004647, -0.000011, 0.008230, 0.015652, 0.019436, 0.023069, 0.024762, 0.027750, 0.028115, 0.026227, 0.022220, 0.023166, 0.020341, 0.018455, 0.014918, 0.011932, 0.007138, 0.008523, 0.014718, 0.026201
	-0.041448, -0.035286, -0.036538, -0.037577, -0.044652, -0.049300, -0.051092, -0.052841, -0.058068, -0.056947, -0.046235, -0.038436, -0.037494, -0.034175, -0.028932, -0.016904, -0.010075, -0.010552, -0.004464, -0.001243, 0.003236, 0.010200, 0.015604, 0.020362, 0.023157, 0.028023, 0.032826, 0.035958, 0.034819, 0.030600, 0.025988, 0.026013, 0.026284, 0.025661, 0.022322, 0.013336, 0.006464, 0.011312, 0.022330, 0.031668
	-0.048540, -0.022534, -0.035260, -0.042156, -0.042749, -0.037408, -0.038818, -0.047322, -0.056808, -0.053643, -0.035691, -0.027822, -0.028789, -0.028255, -0.020274, -0.007285, -0.000723, -0.000788, 0.005440, 0.008938, 0.008953, 0.012074, 0.017957, 0.025241, 0.029175, 0.032057, 0.033733, 0.038359, 0.039349, 0.037161, 0.034052, 0.034585, 0.032020, 0.029940, 0.026326, 0.024577, 0.020432, 0.021586, 0.024568, 0.034552
	-0.033086, -0.027982, -0.029443, -0.029011, -0.035629, -0.040579, -0.038290, -0.037389, -0.041260, -0.040430, -0.032279, -0.021394, -0.018817, -0.015525, -0.007558, 0.006345, 0.011048, 0.011271, 0.013497, 0.017030, 0.017449, 0.022752, 0.026764, 0.030722, 0.033532, 0.037203, 0.043356, 0.048536, 0.047776, 0.043851, 0.039311, 0.039944, 0.039954, 0.038931, 0.034893, 0.030946, 0.023127, 0.027359, 0.034859, 0.043920
	-0.036218, -0.016846, -0.030897, -0.036980, -0.037261, -0.033334, -0.030888, -0.034074, -0.042142, -0.039980, -0.021377, -0.013603, -0.014171, -0.013131, -0.001768, 0.014998, 0.020060, 0.018173, 0.019934, 0.024704, 0.023739, 0.024617, 0.027288, 0.035116, 0.041187, 0.043128, 0.045921, 0.051709, 0.053031, 0.050698, 0.047697, 0.047728, 0.046845, 0.043201, 0.041805, 0.040728, 0.036184, 0.034435, 0.035120, 0.045329
	-0.029808, -0.023871, -0.026541, -0.026705, -0.031203, -0.036908, -0.034411, -0.029231, -0.028090, -0.026102, -0.016691, -0.007747, -0.004471, 0.001560, 0.010738, 0.025062, 0.027672, 0.024833, 0.026976, 0.029502, 0.030754, 0.035709, 0.039403, 0.044719, 0.046379, 0.049250, 0.054178, 0.059793, 0.059542, 0.052111, 0.047608, 0.050103, 0.053142, 0.052747, 0.050045, 0.044102, 0.033149, 0.035392, 0.045678, 0.054080
	-0.032238, -0.008993, -0.023999, -0.030969, -0.028658, -0.024887, -0.024493, -0.028088, -0.031053, -0.022849, -0.003868, 0.004647, 0.004540, 0.007560, 0.018373, 0.031401, 0.035778, 0.033768, 0.035173, 0.035884, 0.036597, 0.038940, 0.044566, 0.053914, 0.056554, 0.056382, 0.056449, 0.060387, 0.062696, 0.058223, 0.055016, 0.056193, 0.056891, 0.052793, 0.052741, 0.052626, 0.048117, 0.045032, 0.048033, 0.055100
	-0.019758, -0.015110, -0.017814, -0.018871, -0.023340, -0.028653, -0.026880, -0.018681, -0.017020, -0.011343, -0.001002, 0.008249, 0.014012, 0.020367, 0.026878, 0.038534, 0.041827, 0.039532, 0.039775, 0.039109, 0.043172, 0.049325, 0.056604, 0.059583, 0.059329, 0.059876, 0.062766, 0.068759, 0.067214, 0.059657, 0.055950, 0.056798, 0.058619, 0.058591, 0.059849, 0.056473, 0.046841, 0.047921, 0.058342, 0.065346
	-0.018628, -0.000296, -0.014764, -0.022634, -0.020483, -0.016362, -0.015485, -0.017352, -0.020246, -0.010362, 0.008635, 0.018414, 0.018542, 0.024258, 0.033370, 0.045728, 0.049983, 0.044610, 0.044638, 0.047649, 0.049220, 0.051954, 0.058932, 0.065915, 0.069102, 0.067410, 0.067680, 0.073734, 0.072203, 0.067293, 0.063945, 0.064378, 0.065047, 0.061989, 0.062882, 0.063468, 0.059707, 0.057986, 0.059739, 0.066139
	-0.010091, -0.006551, -0.008018, -0.009589, -0.016068, -0.020662, -0.019451, -0.010985, -0.009391, -0.003580, 0.007826, 0.019598, 0.024961, 0.033762, 0.040618, 0.050868, 0.052139, 0.050495, 0.049198, 0.051777, 0.056840, 0.061771, 0.068414, 0.072295, 0.073443, 0.072145, 0.073414, 0.079338, 0.075988, 0.067367, 0.064745, 0.064435, 0.066982, 0.065811, 0.067424, 0.063230, 0.058438, 0.059982, 0.067672, 0.072460
	-0.016254, 0.006291, -0.008031, -0.013944, -0.014475, -0.010741, -0.009932, -0.011709, -0.015503, -0.006971, 0.013190, 0.024865, 0.029121, 0.033942, 0.044335, 0.054572, 0.058078, 0.055224, 0.055897, 0.058327, 0.061207, 0.063939, 0.070506, 0.078141, 0.084203, 0.081223, 0.079519, 0.082883, 0.080890, 0.076174, 0.071279, 0.073064, 0.071225, 0.066859, 0.069860, 0.070836, 0.069427, 0.069140, 0.070950, 0.075269
	-0.008127, 0.000730, 0.001164, -0.000308, -0.006659, -0.012343, -0.011463, -0.003755, -0.001876, 0.005166, 0.016616, 0.030243, 0.036509, 0.045020, 0.053681, 0.063738, 0.066425, 0.063964, 0.062796, 0.065633, 0.071912, 0.077280, 0.082580, 0.086477, 0.089798, 0.089603, 0.091453, 0.096125, 0.088708, 0.079903, 0.074317, 0.076190, 0.075399, 0.075242, 0.079628, 0.077855, 0.071473, 0.073702, 0.082757, 0.088086
	-0.010951, 0.013218, -0.000878, -0.006241, -0.005623, 0.000046, 0.000158, -0.002943, -0.005314, 0.005491, 0.026890, 0.035754, 0.041490, 0.045829, 0.059325, 0.070249, 0.074114, 0.071815, 0.073229, 0.076313, 0.080778, 0.081554, 0.087919, 0.096206, 0.101562, 0.101674, 0.100494, 0.103989, 0.100292, 0.093977, 0.088080, 0.088136, 0.086555, 0.081494, 0.084966, 0.087073, 0.084113, 0.085184, 0.087700, 0.092188
	-0.002972, 0.006020, 0.006098, 0.004303, 0.001326, -0.002386, -0.001840, 0.005325, 0.008624, 0.016246, 0.026781, 0.039696, 0.048540, 0.055938, 0.066982, 0.076497, 0.080828, 0.079669, 0.080127, 0.083754, 0.089783, 0.093456, 0.100570, 0.105322, 0.107132, 0.110571, 0.113141, 0.118064, 0.111721, 0.101634, 0.093555, 0.093112, 0.093104, 0.092325, 0.094780, 0.092552, 0.085283, 0.088882, 0.097508, 0.105280
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 11.4
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Preperations]
version = 1
points = 
	0.012158, -0.006098, -0.020628, -0.034069, -0.049418, -0.058491, -0.062706, -0.063181, -0.065552, -0.063461, -0.057373, -0.056717, -0.056579, -0.054080, -0.053373, -0.056878, -0.057281, -0.055224, -0.049676, -0.047605, -0.041454, -0.034605, -0.022490, -0.011292, -0.009411, -0.005344, -0.003510, -0.002717, -0.005999, -0.010712, -0.013141, -0.015611, -0.020004, -0.017667, -0.016629, -0.022248, -0.024864, -0.024065, -0.014921, -0.010826
	-0.005958, -0.021084, -0.033800, -0.047903, -0.059950, -0.071345, -0.072502, -0.073350, -0.075852, -0.072963, -0.067236, -0.064315, -0.065698, -0.064338, -0.062871, -0.065238, -0.067095, -0.063584, -0.059241, -0.057846, -0.051380, -0.043157, -0.030230, -0.019950, -0.018121, -0.014291, -0.009354, -0.013065, -0.016464, -0.022925, -0.025337, -0.026541, -0.030577, -0.029068, -0.027094, -0.030532, -0.034241, -0.032625, -0.021498, -0.020513
	-0.017526, -0.027763, -0.040710, -0.055305, -0.068172, -0.079641, -0.081247, -0.081903, -0.083679, -0.081855, -0.073270, -0.070340, -0.072083, -0.071536, -0.066055, -0.065901, -0.069085, -0.066531, -0.063284, -0.061616, -0.053366, -0.047292, -0.035451, -0.023167, -0.022205, -0.016699, -0.012552, -0.014153, -0.018802, -0.030443, -0.032210, -0.034051, -0.034437, -0.031439, -0.030406, -0.032817, -0.036351, -0.034849, -0.024250, -0.019489
	-0.017750, -0.030284, -0.043463, -0.055839, -0.071865, -0.084888, -0.086157, -0.084619, -0.086681, -0.084515, -0.075246, -0.073263, -0.075604, -0.075123, -0.069177, -0.070723, -0.071097, -0.068644, -0.065465, -0.063718, -0.057574, -0.049335, -0.036556, -0.028418, -0.028259, -0.023387, -0.018454, -0.020519, -0.027499, -0.038314, -0.041534, -0.041886, -0.039972, -0.036438, -0.033959, -0.033009, -0.038291, -0.036339, -0.022688, -0.024783
	-0.021354, -0.034103, -0.047541, -0.060551, -0.075691, -0.089373, -0.092241, -0.091621, -0.093203, -0.090723, -0.082480, -0.079781, -0.079706, -0.079674, -0.074365, -0.073780, -0.073465, -0.070165, -0.064970, -0.065503, -0.059104, -0.051038, -0.041817, -0.031243, -0.031386, -0.028837, -0.023658, -0.024237, -0.029641, -0.039210, -0.042766, -0.044461, -0.041863, -0.039075, -0.034881, -0.034571, -0.039386, -0.038253, -0.031659, -0.024202
	-0.027696, -0.041184, -0.054054, -0.064759, -0.080898, -0.094964, -0.097906, -0.098033, -0.101256, -0.098300, -0.091517, -0.088420, -0.086945, -0.085220, -0.079938, -0.079979, -0.079828, -0.074842, -0.072903, -0.072415, -0.065384, -0.057454, -0.048482, -0.040977, -0.039336, -0.036065, -0.032553, -0.034336, -0.039337, -0.046271, -0.049398, -0.051220, -0.049530, -0.045000, -0.045029, -0.042100, -0.049767, -0.046386, -0.035574, -0.032188
	-0.033426, -0.046259, -0.059363, -0.068024, -0.084858, -0.097009, -0.103434, -0.106215, -0.107319, -0.106178, -0.100333, -0.097536, -0.095352, -0.091322, -0.086332, -0.082309, -0.081440, -0.078413, -0.075067, -0.073134, -0.068255, -0.062667, -0.054300, -0.046004, -0.042001, -0.039181, -0.035010, -0.036092, -0.041599, -0.048788, -0.051751, -0.051179, -0.051019, -0.049121, -0.045860, -0.046756, -0.050005, -0.051613, -0.040237, -0.035349
	-0.037931, -0.051993, -0.066455, -0.075044, -0.088177, -0.102890, -0.108223, -0.112373, -0.115787, -0.113421, -0.108543, -0.105936, -0.101048, -0.096863, -0.090726, -0.087882, -0.086665, -0.083874, -0.081096, -0.080894, -0.075125, -0.071038, -0.063072, -0.054696, -0.051039, -0.046728, -0.042566, -0.043887, -0.048745, -0.056834, -0.059808, -0.060521, -0.060664, -0.057968, -0.056317, -0.052477, -0.058814, -0.055877, -0.046325, -0.042545
	-0.041429, -0.053634, -0.067633, -0.077111, -0.090998, -0.103561, -0.109445, -0.114741, -0.120075, -0.119821, -0.114703, -0.110411, -0.105589, -0.099826, -0.093730, -0.089705, -0.087199, -0.086439, -0.082688, -0.082221, -0.078348, -0.073203, -0.065273, -0.058731, -0.054025, -0.049231, -0.044830, -0.043830, -0.045839, -0.054137, -0.059075, -0.059515, -0.058546, -0.056956, -0.054145, -0.053129, -0.056587, -0.056341, -0.047057, -0.039936
	-0.044295, -0.058972, -0.072101, -0.082726, -0.095001, -0.106449, -0.111505, -0.118363, -0.124608, -0.123506, -0.120263, -0.115400, -0.110227, -0.104535, -0.100348, -0.095757, -0.092961, -0.092377, -0.089613, -0.088047, -0.084834, -0.079314, -0.072500, -0.064519, -0.060449, -0.055767, -0.051803, -0.050997, -0.052855, -0.058115, -0.063348, -0.065363, -0.067936, -0.063474, -0.061475, -0.054726, -0.062529, -0.055352, -0.048878, -0.044991
	-0.045804, -0.056574, -0.073308, -0.082450, -0.097495, -0.107467, -0.111501, -0.116418, -0.126724, -0.125980, -0.123231, -0.120494, -0.114667, -0.111289, -0.103451, -0.099228, -0.095880, -0.095882, -0.093328, -0.091000, -0.087051, -0.081909, -0.075949, -0.064971, -0.061050, -0.055137, -0.049046, -0.047319, -0.049806, -0.056968, -0.059608, -0.060249, -0.063032, -0.060556, -0.056284, -0.056263, -0.058891, -0.057890, -0.051554, -0.042382
	-0.049818, -0.062681, -0.076305, -0.084328, -0.098717, -0.107866, -0.113937, -0.120088, -0.128622, -0.128931, -0.126353, -0.123191, -0.118529, -0.115642, -0.106288, -0.103976, -0.099708, -0.097750, -0.094501, -0.094545, -0.090910, -0.085952, -0.077352, -0.067196, -0.062435, -0.057738, -0.052934, -0.051098, -0.055294, -0.061112, -0.063120, -0.067525, -0.067979, -0.066558, -0.064608, -0.060597, -0.067812, -0.057641, -0.056224, -0.046471
	-0.050591, -0.060432, -0.075602, -0.083877, -0.096933, -0.106147, -0.112334, -0.118295, -0.127966, -0.128757, -0.125157, -0.121831, -0.118557, -0.116124, -0.108723, -0.104502, -0.099469, -0.095841, -0.090662, -0.089822, -0.087969, -0.084545, -0.076375, -0.064821, -0.059093, -0.053427, -0.047372, -0.044341, -0.047964, -0.054064, -0.057133, -0.059152, -0.061568, -0.059109, -0.056640, -0.056691, -0.056844, -0.054564, -0.048514, -0.040641
	-0.047704, -0.059564, -0.073127, -0.080945, -0.093764, -0.105483, -0.111501, -0.118792, -0.124812, -0.126576, -0.122064, -0.118087, -0.116126, -0.114867, -0.108053, -0.103336, -0.097558, -0.093250, -0.086537, -0.085303, -0.083677, -0.079292, -0.070542, -0.062526, -0.056818, -0.052534, -0.044035, -0.041353, -0.046942, -0.051329, -0.055481, -0.062777, -0.058499, -0.058025, -0.057390, -0.053562, -0.060843, -0.046555, -0.046260, -0.036083
	-0.046496, -0.052983, -0.067518, -0.076904, -0.091704, -0.103105, -0.111995, -0.117751, -0.122307, -0.122941, -0.118230, -0.115004, -0.114258, -0.113138, -0.105515, -0.098417, -0.093384, -0.090070, -0.083281, -0.079846, -0.078725, -0.075452, -0.066225, -0.057269, -0.053103, -0.047808, -0.039772, -0.036834, -0.041270, -0.047376, -0.051111, -0.053848, -0.053029, -0.050301, -0.048919, -0.050775, -0.050121, -0.046842, -0.039633, -0.030497
	-0.040695, -0.051685, -0.064038, -0.070974, -0.086679, -0.101773, -0.109889, -0.114373, -0.117883, -0.118764, -0.113125, -0.110931, -0.111099, -0.109664, -0.098733, -0.093182, -0.090154, -0.086213, -0.077214, -0.077108, -0.075555, -0.069117, -0.060704, -0.054093, -0.049253, -0.044799, -0.037536, -0.035304, -0.040134, -0.045456, -0.051720, -0.056675, -0.053743, -0.052923, -0.049701, -0.050238, -0.056776, -0.041485, -0.041755, -0.027329
	-0.039842, -0.039428, -0.055732, -0.063890, -0.079179, -0.092823, -0.101698, -0.106156, -0.111709, -0.113152, -0.108033, -0.104872, -0.105645, -0.103501, -0.094487, -0.087264, -0.084273, -0.080950, -0.074116, -0.070973, -0.068409, -0.062825, -0.054757, -0.044150, -0.040620, -0.036602, -0.031538, -0.026478, -0.031123, -0.037600, -0.042341, -0.046700, -0.047380, -0.042880, -0.040967, -0.045367, -0.044192, -0.038553, -0.029948, -0.020790
	-0.030596, -0.038279, -0.051528, -0.058981, -0.073983, -0.089044, -0.099173, -0.101740, -0.104830, -0.107083, -0.102306, -0.101554, -0.101336, -0.097146, -0.089217, -0.083800, -0.080621, -0.078071, -0.071535, -0.068328, -0.065806, -0.056882, -0.048683, -0.039756, -0.036349, -0.031328, -0.025351, -0.024133, -0.029773, -0.033858, -0.040011, -0.044146, -0.043900, -0.044797, -0.038019, -0.042319, -0.047297, -0.031851, -0.034318, -0.013527
	-0.032121, -0.034722, -0.047839, -0.054710, -0.069175, -0.084213, -0.094533, -0.097233, -0.100863, -0.104775, -0.099781, -0.097416, -0.098804, -0.096059, -0.086694, -0.079692, -0.076749, -0.074609, -0.068106, -0.063906, -0.061136, -0.055447, -0.045559, -0.035389, -0.029696, -0.025708, -0.020034, -0.017335, -0.022665, -0.028532, -0.032369, -0.035760, -0.037212, -0.035201, -0.032872, -0.034132, -0.035907, -0.032127, -0.025026, -0.009282
	-0.026707, -0.034374, -0.045183, -0.052691, -0.067014, -0.084964, -0.092286, -0.094441, -0.099291, -0.103609, -0.098278, -0.094972, -0.097169, -0.095394, -0.086653, -0.080205, -0.076284, -0.070594, -0.064535, -0.062012, -0.060174, -0.051216, -0.040622, -0.033396, -0.029636, -0.024235, -0.017274, -0.018232, -0.021459, -0.024778, -0.031754, -0.034481, -0.033398, -0.037949, -0.030432, -0.033219, -0.038432, -0.021975, -0.030052, -0.009295
	-0.028559, -0.029280, -0.042071, -0.048655, -0.061603, -0.076257, -0.086817, -0.091815, -0.095682, -0.098682, -0.093729, -0.091168, -0.092213, -0.090073, -0.084070, -0.077048, -0.072045, -0.066267, -0.060309, -0.053639, -0.051696, -0.046852, -0.034069, -0.025602, -0.020640, -0.018021, -0.013180, -0.009049, -0.013846, -0.018012, -0.021061, -0.024515, -0.027068, -0.026804, -0.024283, -0.025595, -0.028234, -0.025272, -0.019246, -0.008595
	-0.025711, -0.029003, -0.038836, -0.048015, -0.058511, -0.074480, -0.083738, -0.087945, -0.091439, -0.094310, -0.090288, -0.087858, -0.088589, -0.086163, -0.081829, -0.075146, -0.071136, -0.064399, -0.057338, -0.052103, -0.049650, -0.043210, -0.032998, -0.023124, -0.020191, -0.016625, -0.012433, -0.010465, -0.009871, -0.015007, -0.021217, -0.021582, -0.023800, -0.027652, -0.021527, -0.027137, -0.030828, -0.020152, -0.026202, -0.008568
	-0.031287, -0.022523, -0.035800, -0.041583, -0.052691, -0.065901, -0.075941, -0.079246, -0.083936, -0.086778, -0.082235, -0.078893, -0.080642, -0.079419, -0.074324, -0.067418, -0.062113, -0.057744, -0.049923, -0.043390, -0.040055, -0.035512, -0.023838, -0.015485, -0.009895, -0.008346, -0.005387, 0.001467, -0.000104, -0.003777, -0.007926, -0.012023, -0.013970, -0.014207, -0.013994, -0.017009, -0.019233, -0.019282, -0.014210, -0.001146
	-0.020719, -0.024043, -0.035160, -0.041635, -0.051902, -0.063884, -0.072884, -0.076738, -0.081856, -0.083761, -0.077857, -0.074651, -0.077952, -0.076310, -0.069721, -0.063240, -0.056775, -0.055188, -0.046711, -0.042996, -0.039499, -0.032268, -0.023129, -0.015735, -0.012305, -0.009383, -0.005789, -0.001996, -0.001166, -0.005106, -0.009634, -0.009864, -0.011905, -0.015913, -0.010246, -0.016645, -0.022975, -0.011972, -0.018524, 0.001048
	-0.026050, -0.019774, -0.032555, -0.037813, -0.044657, -0.054435, -0.065271, -0.071019, -0.075585, -0.077479, -0.072635, -0.069526, -0.071046, -0.070770, -0.063085, -0.055960, -0.050956, -0.049593, -0.042773, -0.034996, -0.032645, -0.029030, -0.020343, -0.011008, -0.005751, -0.003252, 0.000746, 0.003215, 0.001749, -0.000068, -0.001413, -0.002608, -0.005837, -0.007103, -0.008431, -0.012027, -0.015656, -0.014417, -0.006321, 0.003748
	-0.021728, -0.019178, -0.031232, -0.036249, -0.042206, -0.053190, -0.064017, -0.068545, -0.074597, -0.074544, -0.069543, -0.065779, -0.067928, -0.067354, -0.060655, -0.052790, -0.047723, -0.046044, -0.038188, -0.034539, -0.032080, -0.027152, -0.018902, -0.012508, -0.009304, -0.003955, -0.000288, -0.001549, -0.000556, -0.003756, -0.008467, -0.003851, -0.005999, -0.012959, -0.007423, -0.015332, -0.017388, -0.005695, -0.010807, 0.007710
	-0.028204, -0.017096, -0.027984, -0.032129, -0.038374, -0.046561, -0.059356, -0.061847, -0.069228, -0.070551, -0.065474, -0.059719, -0.059893, -0.060271, -0.053666, -0.047202, -0.041189, -0.039979, -0.033189, -0.028761, -0.025714, -0.021660, -0.014905, -0.007841, -0.004669, -0.001174, 0.001874, 0.005613, 0.005527, 0.001504, -0.000694, 0.001892, 0.001885, -0.002506, -0.005619, -0.007166, -0.009935, -0.007406, 0.000545, 0.009983
	-0.019393, -0.017785, -0.025482, -0.028146, -0.036861, -0.047528, -0.055696, -0.059118, -0.064151, -0.066346, -0.060565, -0.055661, -0.055495, -0.051944, -0.048147, -0.040645, -0.036359, -0.035990, -0.026764, -0.024843, -0.023572, -0.019648, -0.013807, -0.006811, -0.004589, -0.000266, 0.003010, 0.004931, 0.006834, 0.003254, -0.001690, 0.003120, 0.001036, -0.005283, 0.000659, -0.007399, -0.010996, -0.000832, -0.006381, 0.012135
	-0.021519, -0.010062, -0.018662, -0.023011, -0.029067, -0.036961, -0.043194, -0.048197, -0.053632, -0.055489, -0.050054, -0.045247, -0.042655, -0.040243, -0.034315, -0.027094, -0.022697, -0.021644, -0.015333, -0.010768, -0.013712, -0.012051, -0.005326, 0.000560, 0.005300, 0.007429, 0.009930, 0.015968, 0.016454, 0.012383, 0.010385, 0.011612, 0.011413, 0.008357, 0.006831, 0.005524, 0.003087, 0.003507, 0.009876, 0.018892
	-0.017331, -0.015238, -0.021971, -0.024651, -0.029507, -0.040209, -0.044232, -0.046101, -0.052689, -0.053151, -0.047133, -0.042985, -0.040475, -0.037020, -0.029999, -0.021348, -0.018232, -0.017876, -0.013058, -0.008535, -0.013279, -0.011527, -0.006296, -0.001615, 0.002270, 0.006991, 0.010272, 0.013407, 0.015950, 0.012503, 0.008026, 0.013701, 0.011513, 0.004867, 0.010667, 0.006774, 0.003571, 0.012416, 0.004875, 0.020961
	-0.022637, -0.011107, -0.018340, -0.023896, -0.028320, -0.038092, -0.041212, -0.041642, -0.044537, -0.046015, -0.041699, -0.035805, -0.033527, -0.030911, -0.022925, -0.010175, -0.007279, -0.008644, -0.005065, -0.000597, -0.003797, -0.004052, 0.000635, 0.006175, 0.010857, 0.012993, 0.016956, 0.022765, 0.023298, 0.020262, 0.018285, 0.019467, 0.021161, 0.018785, 0.017891, 0.017817, 0.013874, 0.012825, 0.015904, 0.025844
	-0.014532, -0.010189, -0.019385, -0.022584, -0.028159, -0.037803, -0.040566, -0.038125, -0.040339, -0.038899, -0.033171, -0.028143, -0.025641, -0.019755, -0.012463, -0.003824, -0.000871, -0.002698, -0.000197, 0.001952, -0.001353, -0.000188, 0.004902, 0.012600, 0.014373, 0.016449, 0.018872, 0.022822, 0.026385, 0.020681, 0.015275, 0.021387, 0.023535, 0.016733, 0.022161, 0.018819, 0.011276, 0.020785, 0.014683, 0.032409
	-0.016972, -0.004835, -0.015539, -0.019706, -0.022971, -0.032222, -0.037732, -0.035551, -0.033892, -0.031679, -0.024624, -0.019946, -0.016412, -0.010040, -0.003445, 0.005991, 0.008364, 0.006410, 0.008289, 0.009260, 0.007409, 0.008691, 0.015230, 0.022729, 0.025465, 0.025502, 0.026102, 0.030309, 0.031861, 0.026963, 0.024651, 0.027000, 0.029039, 0.025577, 0.027217, 0.027660, 0.023245, 0.021705, 0.026383, 0.034120
	-0.007042, -0.003943, -0.013314, -0.016082, -0.020497, -0.030911, -0.035096, -0.030889, -0.029351, -0.025337, -0.018980, -0.012449, -0.008879, -0.001902, 0.003577, 0.011256, 0.012460, 0.010502, 0.011904, 0.011483, 0.010067, 0.013356, 0.020792, 0.027368, 0.026382, 0.028554, 0.028164, 0.029993, 0.033232, 0.028830, 0.022354, 0.027991, 0.029607, 0.020011, 0.031066, 0.031755, 0.025061, 0.037228, 0.024607, 0.041453
	-0.012463, -0.000987, -0.008994, -0.014815, -0.017487, -0.026372, -0.031392, -0.028459, -0.025402, -0.024153, -0.015566, -0.007862, -0.004579, 0.001484, 0.010757, 0.017401, 0.019536, 0.016264, 0.016278, 0.018231, 0.018193, 0.018217, 0.025442, 0.034794, 0.036179, 0.034770, 0.033985, 0.040104, 0.040404, 0.034161, 0.030977, 0.032380, 0.034144, 0.031909, 0.033231, 0.035957, 0.034171, 0.033050, 0.038776, 0.042972
	-0.002758, 0.000700, -0.008467, -0.011525, -0.018705, -0.027522, -0.031609, -0.027494, -0.026315, -0.023221, -0.014164, -0.006562, -0.002205, 0.006453, 0.013689, 0.018647, 0.017673, 0.016751, 0.017380, 0.018782, 0.019038, 0.021992, 0.027475, 0.034748, 0.036870, 0.036635, 0.035394, 0.037519, 0.038008, 0.032063, 0.025834, 0.030409, 0.033142, 0.023991, 0.034882, 0.034323, 0.030317, 0.042711, 0.030793, 0.045129
	-0.011501, 0.004979, -0.003199, -0.009532, -0.013737, -0.022490, -0.028056, -0.025047, -0.023987, -0.021727, -0.011113, -0.003633, 0.003070, 0.010580, 0.020230, 0.025058, 0.026653, 0.024592, 0.024567, 0.025613, 0.027386, 0.029282, 0.037705, 0.042901, 0.046601, 0.045443, 0.044217, 0.048155, 0.045715, 0.039788, 0.034981, 0.038594, 0.038594, 0.034532, 0.038671, 0.042065, 0.040659, 0.042101, 0.045919, 0.050030
	-0.005239, 0.006624, -0.001837, -0.005350, -0.012024, -0.022230, -0.026144, -0.022704, -0.021559, -0.017450, -0.008515, 0.000433, 0.007392, 0.014546, 0.023538, 0.029043, 0.029892, 0.027280, 0.028785, 0.030662, 0.032758, 0.032649, 0.040035, 0.046372, 0.048654, 0.050330, 0.049538, 0.049746, 0.048851, 0.041068, 0.034598, 0.041375, 0.041379, 0.030621, 0.043091, 0.044712, 0.038634, 0.053475, 0.042814, 0.059369
	-0.011843, 0.005417, 0.000007, -0.005709, -0.011391, -0.019100, -0.024151, -0.021274, -0.019356, -0.016953, -0.004422, 0.002891, 0.010688, 0.018353, 0.027665, 0.035281, 0.036655, 0.034937, 0.036795, 0.039994, 0.042705, 0.042668, 0.048600, 0.055673, 0.059602, 0.061002, 0.059934, 0.064283, 0.061835, 0.052838, 0.048644, 0.048401, 0.048158, 0.044262, 0.049173, 0.053313, 0.050054, 0.051718, 0.058112, 0.062677
	-0.003249, 0.007140, -0.000190, -0.005182, -0.010664, -0.017472, -0.021072, -0.018928, -0.015929, -0.011810, -0.001170, 0.006999, 0.014346, 0.022026, 0.033087, 0.037703, 0.039304, 0.038986, 0.040531, 0.042739, 0.044912, 0.045850, 0.052980, 0.060894, 0.062495, 0.065477, 0.066306, 0.069035, 0.066301, 0.058359, 0.048879, 0.054660, 0.053906, 0.042834, 0.051292, 0.054304, 0.049390, 0.064968, 0.053062, 0.067337
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 80.0
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Peperations]
version = 1
points = 
	0.022498, 0.020830, 0.014175, -0.000111, -0.007965, -0.011932, -0.009252, -0.003320, -0.000118, 0.004151, 0.015991, 0.024593, 0.030148, 0.034696, 0.042241, 0.043592, 0.045307, 0.051419, 0.057700, 0.066468, 0.072764, 0.085492, 0.100446, 0.113063, 0.118900, 0.122870, 0.130290, 0.129755, 0.129462, 0.124089, 0.122420, 0.123461, 0.116841, 0.117893, 0.119241, 0.115227, 0.110631, 0.109920, 0.117187, 0.124332
	0.004953, 0.000716, -0.005511, -0.010742, -0.018400, -0.024021, -0.019665, -0.013525, -0.009878, -0.004126, 0.008939, 0.016408, 0.019292, 0.023840, 0.033007, 0.033600, 0.034448, 0.041047, 0.049029, 0.052882, 0.062512, 0.072410, 0.089182, 0.103027, 0.106205, 0.110789, 0.117912, 0.115269, 0.112784, 0.106051, 0.103603, 0.104209, 0.099603, 0.105100, 0.101466, 0.099610, 0.095780, 0.096420, 0.108661, 0.108286
	-0.007933, -0.002801, -0.011350, -0.022484, -0.029473, -0.033231, -0.030354, -0.021826, -0.018408, -0.013209, 0.001640, 0.008984, 0.012027, 0.014149, 0.024334, 0.028649, 0.030597, 0.034667, 0.041223, 0.046241, 0.051968, 0.062511, 0.079099, 0.090699, 0.097837, 0.101667, 0.108218, 0.106595, 0.104490, 0.095444, 0.089512, 0.089259, 0.089179, 0.091741, 0.094161, 0.094254, 0.091002, 0.088753, 0.095405, 0.102343
	-0.010759, -0.012564, -0.018170, -0.023960, -0.033106, -0.040910, -0.038354, -0.031441, -0.026122, -0.019953, -0.006267, 0.000733, 0.002678, 0.006102, 0.015437, 0.019860, 0.022689, 0.029563, 0.035629, 0.037302, 0.045089, 0.055137, 0.070820, 0.082978, 0.087158, 0.088614, 0.094487, 0.093851, 0.091038, 0.080923, 0.074433, 0.073797, 0.073058, 0.081788, 0.080734, 0.083111, 0.078149, 0.079373, 0.091335, 0.087853
	-0.027313, -0.019238, -0.027920, -0.036645, -0.043223, -0.049872, -0.048503, -0.043853, -0.040737, -0.035179, -0.021622, -0.013493, -0.010171, -0.007317, 0.001347, 0.007440, 0.011360, 0.015985, 0.023916, 0.026329, 0.031680, 0.042865, 0.056754, 0.067621, 0.072919, 0.075964, 0.080156, 0.081233, 0.077771, 0.068443, 0.063939, 0.062251, 0.063828, 0.065094, 0.069498, 0.071735, 0.067423, 0.064065, 0.069162, 0.076272
	-0.033298, -0.035618, -0.039940, -0.043358, -0.050731, -0.061413, -0.060545, -0.055944, -0.052261, -0.045471, -0.035624, -0.027633, -0.021472, -0.017300, -0.006949, -0.002776, -0.000154, 0.006413, 0.012882, 0.014721, 0.023411, 0.031711, 0.040565, 0.054702, 0.058761, 0.061734, 0.065369, 0.066037, 0.061059, 0.053849, 0.049600, 0.048373, 0.049189, 0.054631, 0.050470, 0.056349, 0.047074, 0.049651, 0.057444, 0.057485
	-0.046284, -0.039039, -0.049010, -0.054961, -0.061001, -0.068408, -0.069602, -0.066474, -0.063117, -0.059357, -0.049570, -0.041166, -0.035441, -0.029269, -0.019658, -0.012395, -0.008906, -0.005538, 0.002012, 0.008339, 0.013216, 0.018793, 0.031185, 0.040165, 0.047175, 0.050605, 0.054283, 0.054442, 0.049166, 0.043483, 0.039000, 0.040758, 0.040857, 0.040759, 0.042263, 0.043438, 0.040051, 0.035886, 0.041332, 0.048851
	-0.049893, -0.051919, -0.058103, -0.060142, -0.067656, -0.077159, -0.079195, -0.078019, -0.075421, -0.069471, -0.060409, -0.054194, -0.044226, -0.037275, -0.027912, -0.020020, -0.016789, -0.012491, -0.003457, 0.001129, 0.004540, 0.009435, 0.018232, 0.027941, 0.035138, 0.038227, 0.042656, 0.044103, 0.038517, 0.032121, 0.029666, 0.027319, 0.029774, 0.031572, 0.028887, 0.034828, 0.023795, 0.030023, 0.033606, 0.036047
	-0.061015, -0.055279, -0.067497, -0.072234, -0.078637, -0.083600, -0.085954, -0.087271, -0.088647, -0.083447, -0.073398, -0.065920, -0.058009, -0.048810, -0.040714, -0.032533, -0.027328, -0.020402, -0.011382, -0.006547, -0.005452, -0.002712, 0.004649, 0.014201, 0.021442, 0.025510, 0.032890, 0.034711, 0.030965, 0.026329, 0.018828, 0.019246, 0.018861, 0.019611, 0.020596, 0.021396, 0.020172, 0.015723, 0.020537, 0.029677
	-0.063777, -0.066149, -0.073750, -0.076131, -0.084016, -0.091900, -0.093741, -0.094496, -0.094840, -0.089548, -0.084332, -0.077263, -0.068485, -0.061963, -0.051082, -0.043658, -0.037912, -0.032323, -0.024324, -0.019914, -0.018261, -0.013727, -0.003485, 0.004316, 0.011418, 0.017023, 0.022980, 0.024505, 0.018896, 0.014000, 0.009498, 0.006074, 0.009480, 0.007611, 0.008958, 0.010086, -0.000341, 0.010423, 0.010467, 0.016794
	-0.072341, -0.064233, -0.079217, -0.084483, -0.091050, -0.094481, -0.095378, -0.096667, -0.100564, -0.098313, -0.093254, -0.086700, -0.079209, -0.071795, -0.061313, -0.051911, -0.046317, -0.042643, -0.037228, -0.031598, -0.027431, -0.020480, -0.012883, -0.003114, 0.004746, 0.010189, 0.015911, 0.017106, 0.014037, 0.008693, 0.005120, 0.003652, -0.000532, -0.001097, 0.001984, 0.000397, -0.002089, -0.002821, 0.000529, 0.009043
	-0.068927, -0.075835, -0.083530, -0.085213, -0.091299, -0.100015, -0.101020, -0.100921, -0.103349, -0.102493, -0.098069, -0.091292, -0.083452, -0.079672, -0.069612, -0.062472, -0.055862, -0.052233, -0.046746, -0.041991, -0.035219, -0.028225, -0.018698, -0.007309, -0.002458, 0.002051, 0.006595, 0.008468, 0.005218, -0.000205, -0.003131, -0.003647, -0.006151, -0.009154, -0.005539, -0.006971, -0.015297, -0.002874, -0.005242, 0.003706
	-0.070116, -0.067835, -0.086390, -0.089881, -0.095167, -0.099194, -0.100751, -0.103794, -0.106996, -0.105835, -0.098564, -0.092154, -0.085579, -0.083053, -0.074722, -0.066442, -0.059302, -0.053429, -0.047800, -0.042952, -0.039132, -0.034614, -0.025732, -0.012689, -0.005906, 0.001101, 0.006644, 0.010980, 0.007742, 0.002526, -0.000261, -0.004094, -0.008771, -0.008465, -0.007095, -0.008952, -0.010405, -0.010446, -0.006121, 0.002024
	-0.064366, -0.071780, -0.082938, -0.085702, -0.093522, -0.099237, -0.104020, -0.105939, -0.106226, -0.104298, -0.097541, -0.091253, -0.084969, -0.082450, -0.075561, -0.066547, -0.056511, -0.051248, -0.041287, -0.037794, -0.035633, -0.028059, -0.019518, -0.010556, -0.003388, 0.002054, 0.009492, 0.011478, 0.008555, 0.004735, -0.000781, -0.006427, -0.005697, -0.010270, -0.006112, -0.011704, -0.018717, -0.002750, -0.010971, 0.000116
	-0.076795, -0.064801, -0.080209, -0.085175, -0.093457, -0.101077, -0.104981, -0.106367, -0.106821, -0.105708, -0.098545, -0.090759, -0.086929, -0.083491, -0.074306, -0.064805, -0.055933, -0.049959, -0.042853, -0.036270, -0.034463, -0.029587, -0.018780, -0.010103, -0.003533, 0.001632, 0.007909, 0.014370, 0.009281, 0.004666, -0.002974, -0.007301, -0.010185, -0.008299, -0.006340, -0.009678, -0.011333, -0.010684, -0.006289, 0.002763
	-0.067470, -0.065770, -0.074038, -0.076420, -0.085702, -0.098704, -0.101940, -0.102629, -0.101903, -0.100342, -0.093820, -0.086941, -0.083804, -0.081020, -0.067700, -0.059395, -0.054055, -0.047911, -0.039687, -0.035672, -0.032029, -0.025979, -0.017057, -0.006973, -0.001656, 0.002001, 0.007249, 0.012112, 0.006541, 0.000572, -0.006284, -0.010415, -0.012279, -0.015087, -0.007848, -0.016491, -0.019704, -0.005357, -0.013151, 0.002966
	-0.074820, -0.054794, -0.069710, -0.075127, -0.082743, -0.091434, -0.095621, -0.097541, -0.099098, -0.097422, -0.089851, -0.083594, -0.081112, -0.078942, -0.066391, -0.057457, -0.050942, -0.048077, -0.041211, -0.034391, -0.030091, -0.026047, -0.014207, -0.005090, 0.000912, 0.005316, 0.010043, 0.015509, 0.011199, 0.004513, -0.001027, -0.006694, -0.011239, -0.011162, -0.009134, -0.013596, -0.014031, -0.011306, -0.007627, 0.001767
	-0.061695, -0.056074, -0.065188, -0.067950, -0.076218, -0.088303, -0.093436, -0.092999, -0.090937, -0.090555, -0.084407, -0.080354, -0.078692, -0.074308, -0.062767, -0.052729, -0.047475, -0.043949, -0.036669, -0.031720, -0.027940, -0.020058, -0.010125, -0.000940, 0.003512, 0.007720, 0.011869, 0.015296, 0.011180, 0.003886, -0.003309, -0.003380, -0.007926, -0.011633, -0.003540, -0.014182, -0.013975, -0.003720, -0.011797, 0.006338
	-0.070864, -0.046187, -0.061128, -0.065717, -0.072715, -0.083470, -0.088292, -0.087558, -0.087628, -0.089378, -0.083768, -0.077237, -0.077063, -0.071978, -0.061635, -0.052022, -0.046913, -0.041194, -0.034314, -0.028661, -0.027048, -0.021438, -0.009769, -0.001205, 0.004637, 0.008928, 0.013264, 0.017277, 0.013442, 0.007295, 0.003623, -0.002524, -0.004256, -0.005789, -0.004213, -0.007305, -0.010487, -0.010885, -0.006086, 0.007386
	-0.059345, -0.049207, -0.056858, -0.060052, -0.066579, -0.080604, -0.086910, -0.085647, -0.085267, -0.087618, -0.081260, -0.075368, -0.073937, -0.069758, -0.058235, -0.051634, -0.045288, -0.038732, -0.032262, -0.027928, -0.024928, -0.019266, -0.007996, 0.000923, 0.005834, 0.008336, 0.013557, 0.017068, 0.012350, 0.006475, 0.000982, 0.001103, -0.006223, -0.006853, -0.000966, -0.013148, -0.013975, -0.006310, -0.011605, 0.006165
	-0.066591, -0.039715, -0.053663, -0.059514, -0.065911, -0.075018, -0.080214, -0.082968, -0.083447, -0.085380, -0.079055, -0.071985, -0.070247, -0.065856, -0.057767, -0.049975, -0.044481, -0.039103, -0.031217, -0.024927, -0.020997, -0.016440, -0.004831, 0.004061, 0.009463, 0.011160, 0.014777, 0.020638, 0.017816, 0.011360, 0.006171, 0.002164, -0.002119, -0.003117, -0.003031, -0.005156, -0.011400, -0.011762, -0.009295, -0.000001
	-0.060314, -0.046160, -0.052794, -0.054967, -0.062049, -0.074106, -0.080446, -0.081200, -0.080809, -0.080477, -0.076170, -0.070932, -0.069101, -0.063634, -0.055720, -0.049501, -0.044939, -0.040131, -0.032438, -0.022882, -0.017627, -0.012524, -0.001324, 0.006685, 0.011868, 0.013658, 0.016095, 0.021837, 0.020158, 0.012528, 0.006089, 0.005453, -0.000976, -0.002140, 0.001104, -0.010111, -0.010612, -0.007452, -0.014357, 0.001011
	-0.075633, -0.036609, -0.049346, -0.055490, -0.059336, -0.067616, -0.073859, -0.075613, -0.076372, -0.078009, -0.070627, -0.064206, -0.064430, -0.061999, -0.054551, -0.047386, -0.040817, -0.037398, -0.028062, -0.018505, -0.012195, -0.007531, 0.001481, 0.011790, 0.019955, 0.022349, 0.022131, 0.024492, 0.023359, 0.019186, 0.014655, 0.008357, 0.004176, 0.002971, 0.002955, -0.000237, -0.005884, -0.010152, -0.009506, 0.002811
	-0.059008, -0.039658, -0.046978, -0.048324, -0.052285, -0.063338, -0.069082, -0.070556, -0.070625, -0.070049, -0.064460, -0.057403, -0.056723, -0.052882, -0.046968, -0.041507, -0.033211, -0.029974, -0.022900, -0.013579, -0.008803, -0.004962, 0.005653, 0.017026, 0.028171, 0.028651, 0.024731, 0.026850, 0.023371, 0.017073, 0.015171, 0.016616, 0.005521, 0.005756, 0.007586, -0.005103, -0.006856, -0.005604, -0.006599, 0.007528
	-0.068330, -0.030233, -0.043154, -0.047439, -0.047149, -0.051149, -0.060971, -0.063014, -0.065775, -0.064636, -0.058200, -0.050987, -0.050925, -0.050115, -0.041299, -0.033907, -0.026306, -0.024199, -0.017123, -0.009196, -0.006314, -0.003809, 0.004760, 0.015324, 0.026665, 0.029649, 0.028724, 0.027131, 0.025150, 0.021808, 0.019981, 0.016766, 0.012347, 0.008776, 0.005760, -0.000224, -0.004294, -0.005879, -0.002457, 0.010054
	-0.053519, -0.031388, -0.038255, -0.037590, -0.039245, -0.046335, -0.056314, -0.057830, -0.060291, -0.058967, -0.051413, -0.045449, -0.043947, -0.042018, -0.034113, -0.025887, -0.019539, -0.017727, -0.012711, -0.005860, -0.003102, 0.000774, 0.009438, 0.015884, 0.022961, 0.024229, 0.026012, 0.029407, 0.026717, 0.020406, 0.017796, 0.020289, 0.012243, 0.009711, 0.009234, -0.005990, -0.001013, 0.000740, -0.002144, 0.013012
	-0.068972, -0.023416, -0.032912, -0.036134, -0.035915, -0.040435, -0.047452, -0.051460, -0.055021, -0.055776, -0.048697, -0.039554, -0.036785, -0.035561, -0.029056, -0.021075, -0.013416, -0.012134, -0.007237, -0.000622, 0.001662, 0.005393, 0.012038, 0.019764, 0.023514, 0.026252, 0.028191, 0.031400, 0.031365, 0.027993, 0.023275, 0.021009, 0.018930, 0.014093, 0.009022, 0.004773, 0.002094, 0.001348, 0.005643, 0.015078
	-0.050527, -0.022437, -0.028090, -0.026206, -0.028387, -0.036911, -0.041310, -0.044227, -0.046970, -0.046769, -0.038081, -0.031386, -0.029516, -0.024050, -0.019435, -0.012381, -0.005732, -0.004173, 0.000911, 0.006849, 0.007360, 0.010699, 0.017436, 0.023369, 0.028527, 0.029640, 0.031002, 0.034727, 0.036582, 0.030763, 0.026015, 0.028623, 0.020834, 0.016185, 0.016933, 0.002829, 0.004984, 0.009818, 0.008874, 0.020032
	-0.067395, -0.010220, -0.021024, -0.024567, -0.024087, -0.029620, -0.032317, -0.034341, -0.038392, -0.038789, -0.030285, -0.021590, -0.017175, -0.014435, -0.007732, -0.000529, 0.005605, 0.007078, 0.012454, 0.017758, 0.016774, 0.015574, 0.020748, 0.028369, 0.033644, 0.034771, 0.036537, 0.040293, 0.042118, 0.039979, 0.035655, 0.033354, 0.030928, 0.024890, 0.021491, 0.018938, 0.013668, 0.012501, 0.017108, 0.023515
	-0.038833, -0.012802, -0.018564, -0.017459, -0.019062, -0.027068, -0.030119, -0.028336, -0.029665, -0.030695, -0.022239, -0.013522, -0.008358, -0.004785, 0.000463, 0.010662, 0.015564, 0.016950, 0.020281, 0.025300, 0.022680, 0.022717, 0.026679, 0.031617, 0.035801, 0.037098, 0.041294, 0.045640, 0.047879, 0.042000, 0.038044, 0.040629, 0.033892, 0.031247, 0.031584, 0.018500, 0.020116, 0.019823, 0.016638, 0.029979
	-0.054356, -0.002258, -0.012712, -0.017288, -0.016713, -0.022907, -0.024293, -0.021563, -0.022620, -0.021953, -0.015330, -0.005386, -0.000764, 0.002640, 0.009997, 0.022869, 0.028174, 0.027730, 0.030977, 0.035707, 0.032818, 0.030889, 0.033638, 0.038561, 0.044265, 0.045141, 0.047683, 0.051815, 0.054004, 0.050991, 0.045574, 0.043899, 0.044055, 0.039092, 0.035909, 0.032091, 0.026891, 0.022169, 0.024865, 0.030848
	-0.031827, -0.000102, -0.006368, -0.006487, -0.006247, -0.014001, -0.017110, -0.013043, -0.010851, -0.008764, -0.000213, 0.006477, 0.011144, 0.018309, 0.024745, 0.033643, 0.038648, 0.039249, 0.041148, 0.045266, 0.041693, 0.040999, 0.045484, 0.052613, 0.057066, 0.054753, 0.055112, 0.059287, 0.060203, 0.052465, 0.047993, 0.050999, 0.047464, 0.046460, 0.044507, 0.031433, 0.032267, 0.032025, 0.029852, 0.040329
	-0.053848, 0.008122, -0.005187, -0.009032, -0.006543, -0.010012, -0.013005, -0.011663, -0.008957, -0.004668, 0.005458, 0.012800, 0.016893, 0.023554, 0.031737, 0.038741, 0.043870, 0.043337, 0.046621, 0.047581, 0.045654, 0.044827, 0.050363, 0.058747, 0.061023, 0.060485, 0.059059, 0.061821, 0.061391, 0.055971, 0.051067, 0.050038, 0.051018, 0.046533, 0.043334, 0.042562, 0.036118, 0.029798, 0.032773, 0.039524
	-0.025830, 0.006164, -0.000655, 0.000164, 0.000088, -0.008033, -0.011008, -0.006017, -0.001301, 0.004088, 0.011848, 0.020276, 0.024465, 0.033383, 0.039126, 0.044268, 0.047916, 0.047402, 0.050050, 0.050456, 0.048891, 0.051771, 0.058154, 0.063246, 0.065463, 0.063072, 0.060950, 0.065351, 0.064614, 0.057455, 0.051194, 0.055723, 0.050906, 0.046407, 0.048283, 0.036561, 0.037400, 0.036887, 0.031589, 0.046759
	-0.041184, 0.017683, 0.006408, 0.000358, 0.001923, -0.002498, -0.003907, -0.001746, 0.001864, 0.006784, 0.017297, 0.026916, 0.030940, 0.036439, 0.045987, 0.050809, 0.054636, 0.052055, 0.053180, 0.056698, 0.057069, 0.055779, 0.063193, 0.067815, 0.071856, 0.070651, 0.067674, 0.070718, 0.070797, 0.062598, 0.057842, 0.056835, 0.056713, 0.051260, 0.048727, 0.048227, 0.044844, 0.039559, 0.041218, 0.044920
	-0.014008, 0.018619, 0.011274, 0.010878, 0.008771, 0.001246, -0.001819, 0.003600, 0.008052, 0.011983, 0.021970, 0.030757, 0.037662, 0.045972, 0.053195, 0.057661, 0.059206, 0.058383, 0.060240, 0.061039, 0.062504, 0.064497, 0.070278, 0.077704, 0.080246, 0.077015, 0.072985, 0.075685, 0.072584, 0.063534, 0.057732, 0.061938, 0.057545, 0.050931, 0.054863, 0.045820, 0.048882, 0.049675, 0.043484, 0.051538
	-0.045038, 0.028947, 0.019821, 0.012917, 0.013648, 0.007951, 0.005122, 0.007823, 0.012411, 0.015320, 0.025036, 0.036734, 0.045314, 0.052208, 0.062220, 0.065610, 0.068489, 0.066665, 0.068454, 0.069025, 0.071080, 0.073373, 0.079623, 0.085651, 0.088907, 0.088954, 0.084254, 0.084464, 0.080300, 0.072471, 0.067316, 0.066430, 0.065143, 0.057630, 0.058650, 0.059627, 0.057197, 0.054105, 0.055295, 0.057879
	-0.017117, 0.027364, 0.023067, 0.022758, 0.019246, 0.011825, 0.007962, 0.011522, 0.017237, 0.021779, 0.031329, 0.042642, 0.052349, 0.060322, 0.069568, 0.074657, 0.075211, 0.072882, 0.075373, 0.078391, 0.079512, 0.081816, 0.086101, 0.091730, 0.095061, 0.095682, 0.092100, 0.092873, 0.085769, 0.077219, 0.068392, 0.073179, 0.069972, 0.061240, 0.068306, 0.062227, 0.061008, 0.064520, 0.058543, 0.070728
	-0.042759, 0.035472, 0.029514, 0.023812, 0.024176, 0.020576, 0.017397, 0.018716, 0.022981, 0.027634, 0.041262, 0.050991, 0.058558, 0.067060, 0.077829, 0.083609, 0.084719, 0.082815, 0.085352, 0.087363, 0.091238, 0.091692, 0.096562, 0.102513, 0.106436, 0.108184, 0.105828, 0.107257, 0.102415, 0.090768, 0.084257, 0.081410, 0.081286, 0.073523, 0.074433, 0.076576, 0.070376, 0.068350, 0.071896, 0.072962
	-0.003143, 0.035517, 0.033266, 0.032727, 0.031843, 0.025862, 0.023177, 0.026936, 0.032953, 0.037457, 0.049289, 0.057429, 0.066625, 0.072540, 0.083814, 0.089321, 0.092420, 0.093053, 0.094752, 0.096876, 0.098364, 0.101271, 0.105185, 0.113505, 0.115784, 0.118957, 0.117138, 0.117934, 0.110930, 0.101497, 0.091051, 0.092731, 0.090574, 0.079282, 0.084691, 0.078426, 0.073451, 0.081698, 0.072811, 0.084352
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 19.8
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity
=======================
Loaded MCU 'dinghy' 118 commands (v0.12.0-402-g2817b348 / gcc: (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027] binutils: (2.34-4+rpi1+14) 2.34)
MCU 'dinghy' config: ADC_MAX=4095 BUS_PINS_i2c1=PB6,PB7 BUS_PINS_i2c1_PB6_PB7=PB6,PB7 BUS_PINS_i2c1_PB8_PB7=PB8,PB7 BUS_PINS_i2c1_PB8_PB9=PB8,PB9 BUS_PINS_i2c1_PF1_PF0=PF1,PF0 BUS_PINS_i2c1a=PF1,PF0 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi2a=PC2,PC3,PB10 CLOCK_FREQ=48000000 MCU=stm32f072xb PWM_MAX=255 RESERVE_PINS_USB=PA11,PA12 RESERVE_PINS_crystal=PF0,PF1 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
Configured MCU 'dinghy' (1024 moves)
Loaded MCU 'mcu' 118 commands (v0.12.0-402-g2817b348 / gcc: (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027] binutils: (2.34-4+rpi1+14) 2.34)
MCU 'mcu' config: ADC_MAX=4095 BUS_PINS_i2c1_PB6_PB7=PB6,PB7 BUS_PINS_i2c1_PB8_PB9=PB8,PB9 BUS_PINS_i2c2_PB10_PB11=PB10,PB11 BUS_PINS_i2c3_PA8_PC9=PA8,PC9 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi2a=PC2,PC3,PB10 BUS_PINS_spi3a=PC11,PC12,PC10 BUS_PINS_spi4=PE13,PE14,PE12 BUS_PINS_spi5=PF8,PF9,PF7 BUS_PINS_spi5a=PH7,PF11,PH6 BUS_PINS_spi6=PG12,PG14,PG13 CLOCK_FREQ=400000000 MCU=stm32h723xx PWM_MAX=255 RESERVE_PINS_USB=PA11,PA12 RESERVE_PINS_crystal=PH0,PH1 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
Configured MCU 'mcu' (1024 moves)
Loaded MCU 'plasma' 118 commands (v0.12.0-402-g2817b348 / gcc: (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027] binutils: (2.34-4+rpi1+14) 2.34)
MCU 'plasma' config: ADC_MAX=4095 BUS_PINS_i2c0a=gpio0,gpio1 BUS_PINS_i2c0b=gpio4,gpio5 BUS_PINS_i2c0c=gpio8,gpio9 BUS_PINS_i2c0d=gpio12,gpio13 BUS_PINS_i2c0e=gpio16,gpio17 BUS_PINS_i2c0f=gpio20,gpio21 BUS_PINS_i2c0g=gpio24,gpio25 BUS_PINS_i2c0h=gpio28,gpio29 BUS_PINS_i2c1a=gpio2,gpio3 BUS_PINS_i2c1b=gpio6,gpio7 BUS_PINS_i2c1c=gpio10,gpio11 BUS_PINS_i2c1d=gpio14,gpio15 BUS_PINS_i2c1e=gpio18,gpio19 BUS_PINS_i2c1f=gpio22,gpio23 BUS_PINS_i2c1g=gpio26,gpio27 BUS_PINS_spi0_gpio0_gpio3_gpio2=gpio0,gpio3,gpio2 BUS_PINS_spi0_gpio16_gpio19_gpio18=gpio16,gpio19,gpio18 BUS_PINS_spi0_gpio20_gpio23_gpio22=gpio20,gpio23,gpio22 BUS_PINS_spi0_gpio4_gpio3_gpio2=gpio4,gpio3,gpio2 BUS_PINS_spi0_gpio4_gpio7_gpio6=gpio4,gpio7,gpio6 BUS_PINS_spi0a=gpio0,gpio3,gpio2 BUS_PINS_spi0b=gpio4,gpio7,gpio6 BUS_PINS_spi0c=gpio16,gpio19,gpio18 BUS_PINS_spi0d=gpio20,gpio23,gpio22 BUS_PINS_spi1_gpio12_gpio15_gpio14=gpio12,gpio15,gpio14 BUS_PINS_spi1_gpio24_gpio27_gpio26=gpio24,gpio27,gpio26 BUS_PINS_spi1_gpio8_gpio11_gpio10=gpio8,gpio11,gpio10 BUS_PINS_spi1a=gpio8,gpio11,gpio10 BUS_PINS_spi1b=gpio12,gpio15,gpio14 BUS_PINS_spi1c=gpio24,gpio27,gpio26 CLOCK_FREQ=12000000 MCU=rp2040 PWM_MAX=255 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
Configured MCU 'plasma' (1024 moves)
Loaded MCU 'rpi' 119 commands (?-20240727_132503-fv-az659-741 / gcc: (Raspbian 10.2.1-6+rpi1) 10.2.1 20210110 binutils: (GNU Binutils for Raspbian) 2.35.2)
MCU 'rpi' config: ADC_MAX=4095 CLOCK_FREQ=50000000 MCU=linux PCA9685_MAX=4096 PWM_MAX=32768 STATS_SUMSQ_BASE=256
Configured MCU 'rpi' (1024 moves)
Loaded MCU 'toolboard_t0' 118 commands (v0.12.0-402-g2817b348 / gcc: (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027] binutils: (2.34-4+rpi1+14) 2.34)
MCU 'toolboard_t0' config: ADC_MAX=4095 BUS_PINS_i2c1_PA9_PA10=PA9,PA10 BUS_PINS_i2c1_PB6_PB7=PB6,PB7 BUS_PINS_i2c1_PB8_PB9=PB8,PB9 BUS_PINS_i2c2_PB10_PB11=PB10,PB11 BUS_PINS_i2c2_PB13_PB14=PB13,PB14 BUS_PINS_i2c3_PB3_PB4=PB3,PB4 BUS_PINS_i2c3_PC0_PC1=PC0,PC1 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi2_PB2_PB11_PB10=PB2,PB11,PB10 BUS_PINS_spi2a=PC2,PC3,PB10 BUS_PINS_spi3=PB4,PB5,PB3 CLOCK_FREQ=64000000 MCU=stm32g0b1xx PWM_MAX=255 RESERVE_PINS_USB=PA11,PA12 RESERVE_PINS_crystal=PF0,PF1 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
Configured MCU 'toolboard_t0' (1024 moves)
Loaded MCU 'toolboard_t1' 118 commands (v0.12.0-402-g2817b348 / gcc: (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027] binutils: (2.34-4+rpi1+14) 2.34)
MCU 'toolboard_t1' config: ADC_MAX=4095 BUS_PINS_i2c1_PA9_PA10=PA9,PA10 BUS_PINS_i2c1_PB6_PB7=PB6,PB7 BUS_PINS_i2c1_PB8_PB9=PB8,PB9 BUS_PINS_i2c2_PB10_PB11=PB10,PB11 BUS_PINS_i2c2_PB13_PB14=PB13,PB14 BUS_PINS_i2c3_PB3_PB4=PB3,PB4 BUS_PINS_i2c3_PC0_PC1=PC0,PC1 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi2_PB2_PB11_PB10=PB2,PB11,PB10 BUS_PINS_spi2a=PC2,PC3,PB10 BUS_PINS_spi3=PB4,PB5,PB3 CLOCK_FREQ=64000000 MCU=stm32g0b1xx PWM_MAX=255 RESERVE_PINS_USB=PA11,PA12 RESERVE_PINS_crystal=PF0,PF1 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
Configured MCU 'toolboard_t1' (1024 moves)
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Args: ['/home/pi/klipper/klippy/klippy.py', '/home/pi/printer_data/config/printer.cfg', '-l', '/home/pi/printer_data/logs/klippy.log', '-I', '/home/pi/printer_data/comms/klippy.serial', '-a', '/home/pi/printer_data/comms/klippy.sock']
Git version: 'v0.12.0-402-g2817b348-dirty'
Untracked files: klippy/extras/beacon.py, klippy/extras/beacon_adaptive_heat_soak.py, klippy/extras/beacon_mesh.py, klippy/extras/beacon_true_zero_correction.py, klippy/extras/beacon_user_z_offset.py, klippy/extras/fastconfig.py, klippy/extras/gcode_shell_command.py, klippy/extras/linear_movement_vibrations.py, klippy/extras/named_offsets.py, klippy/extras/ratos.py, (+4 files)
Modified files: klippy/extras/neopixel.py
Branch: ratos/v2.1.x
Remote: ratos-fork
Tracked URL: https://github.com/Rat-OS/klipper.git
CPU: 4 core ?
Python: '3.9.2 (default, Jan 24 2026, 09:41:14) \n[GCC 10.2.1 20210110]'
webhooks client 3930049648: {'program': 'Moonraker', 'version': 'v0.9.3-0-g71f9e67'}
=============== Log rollover at Tue Mar 17 01:21:04 2026 ===============
Stats 69.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4723 bytes_read=11348 bytes_retransmit=9 bytes_invalid=0 send_seq=369 receive_seq=369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015003 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=1066 bytes_read=5322 bytes_retransmit=0 bytes_invalid=0 send_seq=149 receive_seq=149 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999941 adj=49998061 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1607 bytes_read=8482 bytes_retransmit=9 bytes_invalid=0 send_seq=183 receive_seq=183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000177 adj=63997473 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1606 bytes_read=8471 bytes_retransmit=9 bytes_invalid=0 send_seq=183 receive_seq=183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997624 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1197 bytes_read=12410 bytes_retransmit=9 bytes_invalid=0 send_seq=153 receive_seq=153 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999420 adj=47997613 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1819 bytes_read=5245 bytes_retransmit=9 bytes_invalid=0 send_seq=150 receive_seq=150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999876 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=25.9 EBB42_Gen2_v1.0_T1: temp=24.9 raspberry_pi: temp=20.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=522 bytes_read=13199 bytes_retransmit=0 bytes_invalid=0 send_seq=82 receive_seq=82 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999833 adj=31998614 coil_temp=18.0 refs=0 mcu_temp=21.15 supply_voltage=3.012 th0: temp=31.1 th1: temp=31.8 th2: temp=31.6 th3: temp=31.5 sysload=0.72 cputime=11.971 memavail=7430468 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 70.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4729 bytes_read=11480 bytes_retransmit=9 bytes_invalid=0 send_seq=370 receive_seq=370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015010 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1072 bytes_read=5351 bytes_retransmit=0 bytes_invalid=0 send_seq=150 receive_seq=150 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999944 adj=49998007 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1613 bytes_read=8582 bytes_retransmit=9 bytes_invalid=0 send_seq=184 receive_seq=184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000172 adj=63997412 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1612 bytes_read=8571 bytes_retransmit=9 bytes_invalid=0 send_seq=184 receive_seq=184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999992 adj=63997487 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1203 bytes_read=12627 bytes_retransmit=9 bytes_invalid=0 send_seq=154 receive_seq=154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999423 adj=47997547 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1825 bytes_read=5261 bytes_retransmit=9 bytes_invalid=0 send_seq=151 receive_seq=151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999876 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=25.8 EBB42_Gen2_v1.0_T1: temp=25.2 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=528 bytes_read=13555 bytes_retransmit=0 bytes_invalid=0 send_seq=83 receive_seq=83 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999833 adj=31998605 coil_temp=18.0 refs=0 mcu_temp=21.15 supply_voltage=3.012 th0: temp=31.2 th1: temp=31.4 th2: temp=31.5 th3: temp=31.4 sysload=0.72 cputime=12.007 memavail=7427876 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 71.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4735 bytes_read=11583 bytes_retransmit=9 bytes_invalid=0 send_seq=371 receive_seq=371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015012 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1078 bytes_read=5367 bytes_retransmit=0 bytes_invalid=0 send_seq=151 receive_seq=151 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999945 adj=49998041 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1619 bytes_read=8696 bytes_retransmit=9 bytes_invalid=0 send_seq=185 receive_seq=185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000168 adj=63997458 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1618 bytes_read=8685 bytes_retransmit=9 bytes_invalid=0 send_seq=185 receive_seq=185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999992 adj=63997467 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1209 bytes_read=12908 bytes_retransmit=9 bytes_invalid=0 send_seq=155 receive_seq=155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999424 adj=47997578 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1831 bytes_read=5277 bytes_retransmit=9 bytes_invalid=0 send_seq=152 receive_seq=152 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999876 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=25.8 EBB42_Gen2_v1.0_T1: temp=25.2 raspberry_pi: temp=20.0  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=534 bytes_read=13911 bytes_retransmit=0 bytes_invalid=0 send_seq=84 receive_seq=84 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999832 adj=31998604 coil_temp=18.0 refs=0 mcu_temp=21.16 supply_voltage=3.012 th0: temp=31.1 th1: temp=31.4 th2: temp=31.5 th3: temp=31.4 sysload=0.75 cputime=12.031 memavail=7428104 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 72.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4741 bytes_read=11686 bytes_retransmit=9 bytes_invalid=0 send_seq=372 receive_seq=372 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015006 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1084 bytes_read=5383 bytes_retransmit=0 bytes_invalid=0 send_seq=152 receive_seq=152 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999949 adj=49998052 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1625 bytes_read=8810 bytes_retransmit=9 bytes_invalid=0 send_seq=186 receive_seq=186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000165 adj=63997498 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1624 bytes_read=8799 bytes_retransmit=9 bytes_invalid=0 send_seq=186 receive_seq=186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999988 adj=63997489 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1215 bytes_read=13140 bytes_retransmit=9 bytes_invalid=0 send_seq=156 receive_seq=156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999429 adj=47997601 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1837 bytes_read=5304 bytes_retransmit=9 bytes_invalid=0 send_seq=153 receive_seq=153 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999876 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=26.0 EBB42_Gen2_v1.0_T1: temp=25.4 raspberry_pi: temp=20.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=540 bytes_read=14267 bytes_retransmit=0 bytes_invalid=0 send_seq=85 receive_seq=85 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999832 adj=31998604 coil_temp=18.0 refs=0 mcu_temp=21.17 supply_voltage=3.012 th0: temp=31.2 th1: temp=31.5 th2: temp=31.5 th3: temp=31.5 sysload=0.75 cputime=12.054 memavail=7428592 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 73.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4747 bytes_read=11818 bytes_retransmit=9 bytes_invalid=0 send_seq=373 receive_seq=373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015003 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1090 bytes_read=5399 bytes_retransmit=0 bytes_invalid=0 send_seq=153 receive_seq=153 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999951 adj=49998097 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1631 bytes_read=8924 bytes_retransmit=9 bytes_invalid=0 send_seq=187 receive_seq=187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000163 adj=63997542 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1630 bytes_read=8913 bytes_retransmit=9 bytes_invalid=0 send_seq=187 receive_seq=187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999986 adj=63997533 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1221 bytes_read=13387 bytes_retransmit=9 bytes_invalid=0 send_seq=157 receive_seq=157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999434 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1843 bytes_read=5320 bytes_retransmit=9 bytes_invalid=0 send_seq=154 receive_seq=154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999876 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=26.2 EBB42_Gen2_v1.0_T1: temp=25.4 raspberry_pi: temp=20.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=546 bytes_read=14623 bytes_retransmit=0 bytes_invalid=0 send_seq=86 receive_seq=86 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999832 adj=31998613 coil_temp=18.0 refs=0 mcu_temp=21.17 supply_voltage=3.012 th0: temp=31.1 th1: temp=31.5 th2: temp=31.6 th3: temp=31.5 sysload=0.75 cputime=12.075 memavail=7432884 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 74.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4753 bytes_read=11933 bytes_retransmit=9 bytes_invalid=0 send_seq=374 receive_seq=374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015000 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1096 bytes_read=5415 bytes_retransmit=0 bytes_invalid=0 send_seq=154 receive_seq=154 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999953 adj=49998114 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1637 bytes_read=9038 bytes_retransmit=9 bytes_invalid=0 send_seq=188 receive_seq=188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000161 adj=63997591 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1636 bytes_read=9027 bytes_retransmit=9 bytes_invalid=0 send_seq=188 receive_seq=188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999983 adj=63997529 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1227 bytes_read=13679 bytes_retransmit=9 bytes_invalid=0 send_seq=158 receive_seq=158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999435 adj=47997692 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1849 bytes_read=5336 bytes_retransmit=9 bytes_invalid=0 send_seq=155 receive_seq=155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999883 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=26.0 EBB42_Gen2_v1.0_T1: temp=25.5 raspberry_pi: temp=20.0  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=552 bytes_read=14979 bytes_retransmit=0 bytes_invalid=0 send_seq=87 receive_seq=87 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999831 adj=31998628 coil_temp=18.0 refs=0 mcu_temp=21.17 supply_voltage=3.011 th0: temp=31.2 th1: temp=31.4 th2: temp=31.6 th3: temp=31.4 sysload=0.75 cputime=12.095 memavail=7432664 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.5 pwm=0.000
Stats 75.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4759 bytes_read=12032 bytes_retransmit=9 bytes_invalid=0 send_seq=375 receive_seq=375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015003 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1102 bytes_read=5444 bytes_retransmit=0 bytes_invalid=0 send_seq=155 receive_seq=155 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999953 adj=49998127 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1643 bytes_read=9152 bytes_retransmit=9 bytes_invalid=0 send_seq=189 receive_seq=189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000158 adj=63997614 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1642 bytes_read=9141 bytes_retransmit=9 bytes_invalid=0 send_seq=189 receive_seq=189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1233 bytes_read=13911 bytes_retransmit=9 bytes_invalid=0 send_seq=159 receive_seq=159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999435 adj=47997690 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1855 bytes_read=5352 bytes_retransmit=9 bytes_invalid=0 send_seq=156 receive_seq=156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999883 adj=11999490 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=26.1 EBB42_Gen2_v1.0_T1: temp=25.5 raspberry_pi: temp=20.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=558 bytes_read=15335 bytes_retransmit=0 bytes_invalid=0 send_seq=88 receive_seq=88 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999832 adj=31998628 coil_temp=18.0 refs=0 mcu_temp=21.17 supply_voltage=3.011 th0: temp=31.0 th1: temp=31.4 th2: temp=31.7 th3: temp=31.4 sysload=0.75 cputime=12.116 memavail=7432480 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 76.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4765 bytes_read=12164 bytes_retransmit=9 bytes_invalid=0 send_seq=376 receive_seq=376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015009 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1108 bytes_read=5460 bytes_retransmit=0 bytes_invalid=0 send_seq=156 receive_seq=156 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999955 adj=49998112 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1649 bytes_read=9252 bytes_retransmit=9 bytes_invalid=0 send_seq=190 receive_seq=190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000158 adj=63997624 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1648 bytes_read=9241 bytes_retransmit=9 bytes_invalid=0 send_seq=190 receive_seq=190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999983 adj=63997530 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1239 bytes_read=14143 bytes_retransmit=9 bytes_invalid=0 send_seq=160 receive_seq=160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999437 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1861 bytes_read=5368 bytes_retransmit=9 bytes_invalid=0 send_seq=157 receive_seq=157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999883 adj=11999474 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=26.0 EBB42_Gen2_v1.0_T1: temp=25.3 raspberry_pi: temp=20.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=564 bytes_read=15691 bytes_retransmit=0 bytes_invalid=0 send_seq=89 receive_seq=89 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999832 adj=31998633 coil_temp=18.0 refs=0 mcu_temp=21.17 supply_voltage=3.011 th0: temp=31.1 th1: temp=31.5 th2: temp=31.5 th3: temp=31.5 sysload=0.77 cputime=12.146 memavail=7432488 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.5 pwm=0.000
ratos: beacon probing regions updated: BeaconProbingRegions(x_offset=0.0, y_offset=27.5, printable_x_max=500.0, printable_y_max=500.0, mesh_proximity_min_coil_pos=(20.0, 20.0), mesh_proximity_max_coil_pos=(480.0, 480.0), mesh_proximity_min_toolhead_pos=(20.0, -7.5), mesh_proximity_max_toolhead_pos=(480.0, 452.5), mesh_contact_min=(20.0, 20.0), mesh_contact_max=(480.0, 480.0), logical_proximity_min_coil_pos=(20.0, 20.0), logical_proximity_max_coil_pos=(480.0, 480.0), logical_proximity_min_toolhead_pos=(20.0, -7.5), logical_proximity_max_toolhead_pos=(480.0, 452.5), logical_contact_min=(10.0, -17.5), logical_contact_max=(490.0, 462.5))
Stats 77.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4771 bytes_read=12267 bytes_retransmit=9 bytes_invalid=0 send_seq=377 receive_seq=377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015017 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1114 bytes_read=5476 bytes_retransmit=0 bytes_invalid=0 send_seq=157 receive_seq=157 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999958 adj=49998116 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1655 bytes_read=9366 bytes_retransmit=9 bytes_invalid=0 send_seq=191 receive_seq=191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000160 adj=63997646 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1654 bytes_read=9355 bytes_retransmit=9 bytes_invalid=0 send_seq=191 receive_seq=191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999981 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1245 bytes_read=14435 bytes_retransmit=9 bytes_invalid=0 send_seq=161 receive_seq=161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999438 adj=47997679 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1867 bytes_read=5395 bytes_retransmit=9 bytes_invalid=0 send_seq=158 receive_seq=158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999884 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=26.1 EBB42_Gen2_v1.0_T1: temp=25.6 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=570 bytes_read=16047 bytes_retransmit=0 bytes_invalid=0 send_seq=90 receive_seq=90 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999833 adj=31998625 coil_temp=18.0 refs=0 mcu_temp=21.17 supply_voltage=3.011 th0: temp=31.1 th1: temp=31.5 th2: temp=31.6 th3: temp=31.5 sysload=0.77 cputime=12.280 memavail=7426268 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 78.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4777 bytes_read=12370 bytes_retransmit=9 bytes_invalid=0 send_seq=378 receive_seq=378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015024 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1120 bytes_read=5492 bytes_retransmit=0 bytes_invalid=0 send_seq=158 receive_seq=158 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999963 adj=49998124 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1661 bytes_read=9494 bytes_retransmit=9 bytes_invalid=0 send_seq=192 receive_seq=192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000160 adj=63997682 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1660 bytes_read=9483 bytes_retransmit=9 bytes_invalid=0 send_seq=192 receive_seq=192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999979 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1251 bytes_read=14682 bytes_retransmit=9 bytes_invalid=0 send_seq=162 receive_seq=162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999438 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1873 bytes_read=5411 bytes_retransmit=9 bytes_invalid=0 send_seq=159 receive_seq=159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999884 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=26.2 EBB42_Gen2_v1.0_T1: temp=25.5 raspberry_pi: temp=20.9  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=576 bytes_read=16387 bytes_retransmit=0 bytes_invalid=0 send_seq=91 receive_seq=91 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999835 adj=31998632 coil_temp=18.0 refs=0 mcu_temp=21.17 supply_voltage=3.011 th0: temp=31.0 th1: temp=31.7 th2: temp=31.6 th3: temp=31.4 sysload=0.77 cputime=12.314 memavail=7428456 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 79.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4783 bytes_read=12516 bytes_retransmit=9 bytes_invalid=0 send_seq=379 receive_seq=379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015039 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1126 bytes_read=5508 bytes_retransmit=0 bytes_invalid=0 send_seq=159 receive_seq=159 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999963 adj=49998146 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1667 bytes_read=9594 bytes_retransmit=9 bytes_invalid=0 send_seq=193 receive_seq=193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000176 adj=63997684 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1666 bytes_read=9583 bytes_retransmit=9 bytes_invalid=0 send_seq=193 receive_seq=193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999979 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1257 bytes_read=14914 bytes_retransmit=9 bytes_invalid=0 send_seq=163 receive_seq=163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999439 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1879 bytes_read=5427 bytes_retransmit=9 bytes_invalid=0 send_seq=160 receive_seq=160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999883 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=26.0 EBB42_Gen2_v1.0_T1: temp=25.4 raspberry_pi: temp=20.9  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=582 bytes_read=16743 bytes_retransmit=0 bytes_invalid=0 send_seq=92 receive_seq=92 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999840 adj=31998643 coil_temp=18.0 refs=0 mcu_temp=21.17 supply_voltage=3.012 th0: temp=31.2 th1: temp=31.4 th2: temp=31.7 th3: temp=31.5 sysload=0.77 cputime=12.351 memavail=7425692 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 80.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4789 bytes_read=12619 bytes_retransmit=9 bytes_invalid=0 send_seq=380 receive_seq=380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015052 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1132 bytes_read=5537 bytes_retransmit=0 bytes_invalid=0 send_seq=160 receive_seq=160 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999965 adj=49998113 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1673 bytes_read=9708 bytes_retransmit=9 bytes_invalid=0 send_seq=194 receive_seq=194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997833 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1672 bytes_read=9697 bytes_retransmit=9 bytes_invalid=0 send_seq=194 receive_seq=194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999980 adj=63997494 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1263 bytes_read=15206 bytes_retransmit=9 bytes_invalid=0 send_seq=164 receive_seq=164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999453 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1885 bytes_read=5443 bytes_retransmit=9 bytes_invalid=0 send_seq=161 receive_seq=161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999887 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=26.1 EBB42_Gen2_v1.0_T1: temp=25.6 raspberry_pi: temp=20.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=588 bytes_read=17099 bytes_retransmit=0 bytes_invalid=0 send_seq=93 receive_seq=93 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999838 adj=31998672 coil_temp=18.0 refs=0 mcu_temp=21.16 supply_voltage=3.012 th0: temp=31.1 th1: temp=31.5 th2: temp=31.6 th3: temp=31.5 sysload=0.77 cputime=12.383 memavail=7425692 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 81.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4795 bytes_read=12722 bytes_retransmit=9 bytes_invalid=0 send_seq=381 receive_seq=381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015057 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1138 bytes_read=5553 bytes_retransmit=0 bytes_invalid=0 send_seq=161 receive_seq=161 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999968 adj=49998108 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1679 bytes_read=9822 bytes_retransmit=9 bytes_invalid=0 send_seq=195 receive_seq=195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997984 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1678 bytes_read=9811 bytes_retransmit=9 bytes_invalid=0 send_seq=195 receive_seq=195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999978 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1269 bytes_read=15438 bytes_retransmit=9 bytes_invalid=0 send_seq=165 receive_seq=165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999452 adj=47997758 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1891 bytes_read=5459 bytes_retransmit=9 bytes_invalid=0 send_seq=162 receive_seq=162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999886 adj=11999470 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=26.2 EBB42_Gen2_v1.0_T1: temp=25.5 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=594 bytes_read=17455 bytes_retransmit=0 bytes_invalid=0 send_seq=94 receive_seq=94 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999839 adj=31998641 coil_temp=18.0 refs=0 mcu_temp=21.16 supply_voltage=3.012 th0: temp=31.0 th1: temp=31.4 th2: temp=31.6 th3: temp=31.5 sysload=0.79 cputime=12.414 memavail=7425692 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 82.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4801 bytes_read=12854 bytes_retransmit=9 bytes_invalid=0 send_seq=382 receive_seq=382 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015056 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1144 bytes_read=5569 bytes_retransmit=0 bytes_invalid=0 send_seq=162 receive_seq=162 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999968 adj=49998128 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1685 bytes_read=9922 bytes_retransmit=9 bytes_invalid=0 send_seq=196 receive_seq=196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997987 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1684 bytes_read=9911 bytes_retransmit=9 bytes_invalid=0 send_seq=196 receive_seq=196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999976 adj=63997493 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1275 bytes_read=15670 bytes_retransmit=9 bytes_invalid=0 send_seq=166 receive_seq=166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999453 adj=47997717 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1897 bytes_read=5486 bytes_retransmit=9 bytes_invalid=0 send_seq=163 receive_seq=163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999886 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=26.3 EBB42_Gen2_v1.0_T1: temp=25.6 raspberry_pi: temp=20.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=600 bytes_read=17811 bytes_retransmit=0 bytes_invalid=0 send_seq=95 receive_seq=95 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999839 adj=31998641 coil_temp=18.0 refs=0 mcu_temp=21.17 supply_voltage=3.012 th0: temp=30.9 th1: temp=31.5 th2: temp=31.4 th3: temp=31.4 sysload=0.79 cputime=12.445 memavail=7425692 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 83.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4807 bytes_read=12957 bytes_retransmit=9 bytes_invalid=0 send_seq=383 receive_seq=383 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015068 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1150 bytes_read=5585 bytes_retransmit=0 bytes_invalid=0 send_seq=163 receive_seq=163 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999969 adj=49998124 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1691 bytes_read=10050 bytes_retransmit=9 bytes_invalid=0 send_seq=197 receive_seq=197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997895 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1690 bytes_read=10039 bytes_retransmit=9 bytes_invalid=0 send_seq=197 receive_seq=197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999976 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1281 bytes_read=15977 bytes_retransmit=9 bytes_invalid=0 send_seq=167 receive_seq=167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999453 adj=47997708 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1903 bytes_read=5502 bytes_retransmit=9 bytes_invalid=0 send_seq=164 receive_seq=164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999885 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=26.3 EBB42_Gen2_v1.0_T1: temp=25.6 raspberry_pi: temp=20.0  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=606 bytes_read=18167 bytes_retransmit=0 bytes_invalid=0 send_seq=96 receive_seq=96 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999845 adj=31998638 coil_temp=18.0 refs=0 mcu_temp=21.17 supply_voltage=3.012 th0: temp=31.1 th1: temp=31.6 th2: temp=31.7 th3: temp=31.5 sysload=0.79 cputime=12.478 memavail=7427892 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 84.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4813 bytes_read=13074 bytes_retransmit=9 bytes_invalid=0 send_seq=384 receive_seq=384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015073 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1156 bytes_read=5601 bytes_retransmit=0 bytes_invalid=0 send_seq=164 receive_seq=164 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999970 adj=49998105 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1697 bytes_read=10164 bytes_retransmit=9 bytes_invalid=0 send_seq=198 receive_seq=198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997807 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1696 bytes_read=10153 bytes_retransmit=9 bytes_invalid=0 send_seq=198 receive_seq=198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999975 adj=63997499 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1287 bytes_read=16209 bytes_retransmit=9 bytes_invalid=0 send_seq=168 receive_seq=168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999452 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1909 bytes_read=5518 bytes_retransmit=9 bytes_invalid=0 send_seq=165 receive_seq=165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999885 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=26.3 EBB42_Gen2_v1.0_T1: temp=25.5 raspberry_pi: temp=20.9  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=612 bytes_read=18523 bytes_retransmit=0 bytes_invalid=0 send_seq=97 receive_seq=97 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999844 adj=31998687 coil_temp=18.0 refs=0 mcu_temp=21.17 supply_voltage=3.012 th0: temp=31.2 th1: temp=31.5 th2: temp=31.6 th3: temp=31.5 sysload=0.79 cputime=12.509 memavail=7427884 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 85.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4819 bytes_read=13202 bytes_retransmit=9 bytes_invalid=0 send_seq=385 receive_seq=385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015070 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1162 bytes_read=5630 bytes_retransmit=0 bytes_invalid=0 send_seq=165 receive_seq=165 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999978 adj=49998108 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1703 bytes_read=10264 bytes_retransmit=9 bytes_invalid=0 send_seq=199 receive_seq=199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997751 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1702 bytes_read=10253 bytes_retransmit=9 bytes_invalid=0 send_seq=199 receive_seq=199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999975 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1293 bytes_read=16441 bytes_retransmit=9 bytes_invalid=0 send_seq=169 receive_seq=169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999451 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1915 bytes_read=5534 bytes_retransmit=9 bytes_invalid=0 send_seq=166 receive_seq=166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999884 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=26.5 EBB42_Gen2_v1.0_T1: temp=25.6 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=618 bytes_read=18879 bytes_retransmit=0 bytes_invalid=0 send_seq=98 receive_seq=98 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999844 adj=31998666 coil_temp=18.0 refs=0 mcu_temp=21.17 supply_voltage=3.012 th0: temp=31.1 th1: temp=31.4 th2: temp=31.5 th3: temp=31.5 sysload=0.79 cputime=12.540 memavail=7430736 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 86.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4825 bytes_read=13304 bytes_retransmit=9 bytes_invalid=0 send_seq=386 receive_seq=386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015070 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1168 bytes_read=5646 bytes_retransmit=0 bytes_invalid=0 send_seq=166 receive_seq=166 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999980 adj=49998185 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1709 bytes_read=10378 bytes_retransmit=9 bytes_invalid=0 send_seq=200 receive_seq=200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997745 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1708 bytes_read=10367 bytes_retransmit=9 bytes_invalid=0 send_seq=200 receive_seq=200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999974 adj=63997522 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1299 bytes_read=16733 bytes_retransmit=9 bytes_invalid=0 send_seq=170 receive_seq=170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999452 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1921 bytes_read=5550 bytes_retransmit=9 bytes_invalid=0 send_seq=167 receive_seq=167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999886 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=26.3 EBB42_Gen2_v1.0_T1: temp=25.6 raspberry_pi: temp=20.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=624 bytes_read=19235 bytes_retransmit=0 bytes_invalid=0 send_seq=99 receive_seq=99 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999843 adj=31998657 coil_temp=18.0 refs=0 mcu_temp=21.17 supply_voltage=3.011 th0: temp=31.2 th1: temp=31.5 th2: temp=31.7 th3: temp=31.5 sysload=0.80 cputime=12.572 memavail=7430500 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 87.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4831 bytes_read=13407 bytes_retransmit=9 bytes_invalid=0 send_seq=387 receive_seq=387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015077 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1174 bytes_read=5662 bytes_retransmit=0 bytes_invalid=0 send_seq=167 receive_seq=167 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999981 adj=49998187 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1715 bytes_read=10492 bytes_retransmit=9 bytes_invalid=0 send_seq=201 receive_seq=201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997743 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1714 bytes_read=10481 bytes_retransmit=9 bytes_invalid=0 send_seq=201 receive_seq=201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999973 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1305 bytes_read=16965 bytes_retransmit=9 bytes_invalid=0 send_seq=171 receive_seq=171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999451 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1927 bytes_read=5577 bytes_retransmit=9 bytes_invalid=0 send_seq=168 receive_seq=168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999886 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=26.4 EBB42_Gen2_v1.0_T1: temp=25.6 raspberry_pi: temp=20.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=630 bytes_read=19591 bytes_retransmit=0 bytes_invalid=0 send_seq=100 receive_seq=100 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999843 adj=31998650 coil_temp=18.0 refs=0 mcu_temp=21.17 supply_voltage=3.011 th0: temp=31.1 th1: temp=31.4 th2: temp=31.5 th3: temp=31.5 sysload=0.80 cputime=12.603 memavail=7430500 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 88.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4837 bytes_read=13539 bytes_retransmit=9 bytes_invalid=0 send_seq=388 receive_seq=388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015078 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1180 bytes_read=5678 bytes_retransmit=0 bytes_invalid=0 send_seq=168 receive_seq=168 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999980 adj=49998164 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1721 bytes_read=10606 bytes_retransmit=9 bytes_invalid=0 send_seq=202 receive_seq=202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997697 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1720 bytes_read=10595 bytes_retransmit=9 bytes_invalid=0 send_seq=202 receive_seq=202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999972 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1311 bytes_read=17212 bytes_retransmit=9 bytes_invalid=0 send_seq=172 receive_seq=172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999450 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1933 bytes_read=5593 bytes_retransmit=9 bytes_invalid=0 send_seq=169 receive_seq=169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999886 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=26.3 EBB42_Gen2_v1.0_T1: temp=25.7 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=636 bytes_read=19947 bytes_retransmit=0 bytes_invalid=0 send_seq=101 receive_seq=101 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999843 adj=31998638 coil_temp=18.0 refs=0 mcu_temp=21.17 supply_voltage=3.012 th0: temp=31.2 th1: temp=31.5 th2: temp=31.4 th3: temp=31.4 sysload=0.80 cputime=12.634 memavail=7430500 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.5 pwm=0.000
Stats 89.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4843 bytes_read=13656 bytes_retransmit=9 bytes_invalid=0 send_seq=389 receive_seq=389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015076 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1186 bytes_read=5694 bytes_retransmit=0 bytes_invalid=0 send_seq=169 receive_seq=169 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999978 adj=49998138 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1727 bytes_read=10720 bytes_retransmit=9 bytes_invalid=0 send_seq=203 receive_seq=203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997728 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1726 bytes_read=10709 bytes_retransmit=9 bytes_invalid=0 send_seq=203 receive_seq=203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999972 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1317 bytes_read=17504 bytes_retransmit=9 bytes_invalid=0 send_seq=173 receive_seq=173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999452 adj=47997626 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1939 bytes_read=5609 bytes_retransmit=9 bytes_invalid=0 send_seq=170 receive_seq=170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999885 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=26.3 EBB42_Gen2_v1.0_T1: temp=25.7 raspberry_pi: temp=20.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=642 bytes_read=20303 bytes_retransmit=0 bytes_invalid=0 send_seq=102 receive_seq=102 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999842 adj=31998638 coil_temp=18.0 refs=0 mcu_temp=21.17 supply_voltage=3.012 th0: temp=31.2 th1: temp=31.4 th2: temp=31.6 th3: temp=31.4 sysload=0.80 cputime=12.666 memavail=7430500 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.5 pwm=0.000
Stats 90.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4849 bytes_read=13759 bytes_retransmit=9 bytes_invalid=0 send_seq=390 receive_seq=390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015076 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1192 bytes_read=5723 bytes_retransmit=0 bytes_invalid=0 send_seq=170 receive_seq=170 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999978 adj=49998113 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1733 bytes_read=10834 bytes_retransmit=9 bytes_invalid=0 send_seq=204 receive_seq=204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997714 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1732 bytes_read=10823 bytes_retransmit=9 bytes_invalid=0 send_seq=204 receive_seq=204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999972 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1323 bytes_read=17736 bytes_retransmit=9 bytes_invalid=0 send_seq=174 receive_seq=174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999458 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1945 bytes_read=5625 bytes_retransmit=9 bytes_invalid=0 send_seq=171 receive_seq=171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999885 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=26.3 EBB42_Gen2_v1.0_T1: temp=25.8 raspberry_pi: temp=20.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=648 bytes_read=20659 bytes_retransmit=0 bytes_invalid=0 send_seq=103 receive_seq=103 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999841 adj=31998662 coil_temp=18.0 refs=0 mcu_temp=21.16 supply_voltage=3.012 th0: temp=31.1 th1: temp=31.5 th2: temp=31.5 th3: temp=31.5 sysload=0.80 cputime=12.698 memavail=7430500 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 91.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4855 bytes_read=13891 bytes_retransmit=9 bytes_invalid=0 send_seq=391 receive_seq=391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015092 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1198 bytes_read=5739 bytes_retransmit=0 bytes_invalid=0 send_seq=171 receive_seq=171 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999977 adj=49998104 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1739 bytes_read=10934 bytes_retransmit=9 bytes_invalid=0 send_seq=205 receive_seq=205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997699 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1738 bytes_read=10923 bytes_retransmit=9 bytes_invalid=0 send_seq=205 receive_seq=205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999971 adj=63997534 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1329 bytes_read=17968 bytes_retransmit=9 bytes_invalid=0 send_seq=175 receive_seq=175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999459 adj=47997716 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1951 bytes_read=5641 bytes_retransmit=9 bytes_invalid=0 send_seq=172 receive_seq=172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999885 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=26.5 EBB42_Gen2_v1.0_T1: temp=25.5 raspberry_pi: temp=20.9  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=654 bytes_read=21015 bytes_retransmit=0 bytes_invalid=0 send_seq=104 receive_seq=104 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999841 adj=31998644 coil_temp=18.0 refs=0 mcu_temp=21.16 supply_voltage=3.012 th0: temp=31.2 th1: temp=31.4 th2: temp=31.5 th3: temp=31.5 sysload=0.74 cputime=12.729 memavail=7430500 print_time=59.933 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.5 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
TMC 'stepper_z' reports GSTAT:      00000001 reset=1(Reset)
TMC 'stepper_z1' reports GSTAT:      00000001 reset=1(Reset)
TMC 'stepper_z2' reports GSTAT:      00000001 reset=1(Reset)
TMC 'stepper_z' reports GSTAT:      00000000
TMC 'stepper_z1' reports GSTAT:      00000000
TMC 'stepper_z2' reports GSTAT:      00000000
Stats 92.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=6631 bytes_read=15434 bytes_retransmit=9 bytes_invalid=0 send_seq=476 receive_seq=476 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015076 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1204 bytes_read=5755 bytes_retransmit=0 bytes_invalid=0 send_seq=172 receive_seq=172 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999984 adj=49998072 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1745 bytes_read=11062 bytes_retransmit=9 bytes_invalid=0 send_seq=206 receive_seq=206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000173 adj=63997660 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1744 bytes_read=11051 bytes_retransmit=9 bytes_invalid=0 send_seq=206 receive_seq=206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999973 adj=63997503 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1335 bytes_read=18260 bytes_retransmit=9 bytes_invalid=0 send_seq=176 receive_seq=176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999458 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1957 bytes_read=5668 bytes_retransmit=9 bytes_invalid=0 send_seq=173 receive_seq=173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999885 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=26.4 EBB42_Gen2_v1.0_T1: temp=25.5 raspberry_pi: temp=20.0  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=660 bytes_read=21360 bytes_retransmit=0 bytes_invalid=0 send_seq=105 receive_seq=105 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999840 adj=31998629 coil_temp=18.0 refs=0 mcu_temp=21.15 supply_voltage=3.012 th0: temp=31.0 th1: temp=31.4 th2: temp=31.7 th3: temp=31.4 sysload=0.74 cputime=12.848 memavail=7430500 print_time=114.699 buffer_time=0.310 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
TMC 'stepper_x' reports GSTAT:      00000005 reset=1(Reset) uv_cp=1(Undervoltage!)
TMC 'stepper_x' reports GSTAT:      00000000
TMC 'stepper_y' reports GSTAT:      00000005 reset=1(Reset) uv_cp=1(Undervoltage!)
TMC 'stepper_y' reports GSTAT:      00000000
TMC 'stepper_y1' reports GSTAT:      00000005 reset=1(Reset) uv_cp=1(Undervoltage!)
TMC 'dual_carriage' reports GSTAT:      00000005 reset=1(Reset) uv_cp=1(Undervoltage!)
TMC 'stepper_y1' reports GSTAT:      00000000
TMC 'dual_carriage' reports GSTAT:      00000000
Stats 93.0: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=10036 bytes_read=18164 bytes_retransmit=9 bytes_invalid=0 send_seq=704 receive_seq=704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015076 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1210 bytes_read=5771 bytes_retransmit=0 bytes_invalid=0 send_seq=173 receive_seq=173 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999984 adj=49998174 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1751 bytes_read=11176 bytes_retransmit=9 bytes_invalid=0 send_seq=207 receive_seq=207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000172 adj=63997698 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1750 bytes_read=11165 bytes_retransmit=9 bytes_invalid=0 send_seq=207 receive_seq=207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999972 adj=63997569 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1369 bytes_read=18517 bytes_retransmit=9 bytes_invalid=0 send_seq=179 receive_seq=179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999457 adj=47997683 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1963 bytes_read=5684 bytes_retransmit=9 bytes_invalid=0 send_seq=174 receive_seq=174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999885 adj=11999433 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=26.5 EBB42_Gen2_v1.0_T1: temp=25.8 raspberry_pi: temp=20.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=666 bytes_read=21705 bytes_retransmit=0 bytes_invalid=0 send_seq=106 receive_seq=106 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999842 adj=31998631 coil_temp=18.0 refs=0 mcu_temp=21.13 supply_voltage=3.012 th0: temp=32.1 th1: temp=31.8 th2: temp=33.4 th3: temp=31.8 sysload=0.74 cputime=12.952 memavail=7430500 print_time=115.566 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.5 pwm=0.000
Stats 94.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=11781 bytes_read=19141 bytes_retransmit=9 bytes_invalid=0 send_seq=778 receive_seq=778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015081 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1216 bytes_read=5787 bytes_retransmit=0 bytes_invalid=0 send_seq=174 receive_seq=174 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999984 adj=49998156 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1757 bytes_read=11276 bytes_retransmit=9 bytes_invalid=0 send_seq=208 receive_seq=208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000172 adj=63997697 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1756 bytes_read=11265 bytes_retransmit=9 bytes_invalid=0 send_seq=208 receive_seq=208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999972 adj=63997560 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1375 bytes_read=18750 bytes_retransmit=9 bytes_invalid=0 send_seq=180 receive_seq=180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999456 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1969 bytes_read=5700 bytes_retransmit=9 bytes_invalid=0 send_seq=175 receive_seq=175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999885 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=26.2 EBB42_Gen2_v1.0_T1: temp=25.9 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=672 bytes_read=22049 bytes_retransmit=0 bytes_invalid=0 send_seq=107 receive_seq=107 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999842 adj=31998661 coil_temp=18.0 refs=0 mcu_temp=21.13 supply_voltage=3.012 th0: temp=32.4 th1: temp=31.8 th2: temp=33.2 th3: temp=32.2 sysload=0.74 cputime=13.022 memavail=7431528 print_time=116.593 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 95.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=15216 bytes_read=20093 bytes_retransmit=9 bytes_invalid=0 send_seq=870 receive_seq=870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015072 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1222 bytes_read=5815 bytes_retransmit=0 bytes_invalid=0 send_seq=175 receive_seq=175 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999984 adj=49998142 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1801 bytes_read=11409 bytes_retransmit=9 bytes_invalid=0 send_seq=210 receive_seq=210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000171 adj=63997708 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1762 bytes_read=11393 bytes_retransmit=9 bytes_invalid=0 send_seq=209 receive_seq=209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999971 adj=63997543 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1381 bytes_read=19043 bytes_retransmit=9 bytes_invalid=0 send_seq=181 receive_seq=181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999457 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1975 bytes_read=5716 bytes_retransmit=9 bytes_invalid=0 send_seq=176 receive_seq=176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999885 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=26.5 EBB42_Gen2_v1.0_T1: temp=25.8 raspberry_pi: temp=20.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=678 bytes_read=22394 bytes_retransmit=0 bytes_invalid=0 send_seq=108 receive_seq=108 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999843 adj=31998645 coil_temp=18.0 refs=0 mcu_temp=21.12 supply_voltage=3.012 th0: temp=31.4 th1: temp=31.8 th2: temp=32.1 th3: temp=32.0 sysload=0.74 cputime=13.115 memavail=7430772 print_time=117.574 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 96.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=17200 bytes_read=22924 bytes_retransmit=9 bytes_invalid=0 send_seq=1037 receive_seq=1037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015073 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1228 bytes_read=5830 bytes_retransmit=0 bytes_invalid=0 send_seq=176 receive_seq=176 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999985 adj=49998137 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=3307 bytes_read=13884 bytes_retransmit=9 bytes_invalid=0 send_seq=336 receive_seq=336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000172 adj=63997725 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1768 bytes_read=11493 bytes_retransmit=9 bytes_invalid=0 send_seq=210 receive_seq=210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999984 adj=63997585 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1387 bytes_read=19276 bytes_retransmit=9 bytes_invalid=0 send_seq=182 receive_seq=182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999460 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1981 bytes_read=5732 bytes_retransmit=9 bytes_invalid=0 send_seq=177 receive_seq=177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999885 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=26.5 EBB42_Gen2_v1.0_T1: temp=25.9 raspberry_pi: temp=20.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=684 bytes_read=22739 bytes_retransmit=0 bytes_invalid=0 send_seq=109 receive_seq=109 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999843 adj=31998665 coil_temp=18.0 refs=0 mcu_temp=21.11 supply_voltage=3.012 th0: temp=32.4 th1: temp=32.2 th2: temp=33.2 th3: temp=32.6 sysload=0.68 cputime=13.232 memavail=7424760 print_time=118.574 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 97.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=19339 bytes_read=25979 bytes_retransmit=9 bytes_invalid=0 send_seq=1214 receive_seq=1214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015062 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1234 bytes_read=5845 bytes_retransmit=0 bytes_invalid=0 send_seq=177 receive_seq=177 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999986 adj=49998138 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=4909 bytes_read=16525 bytes_retransmit=9 bytes_invalid=0 send_seq=470 receive_seq=470 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000170 adj=63997742 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1774 bytes_read=11593 bytes_retransmit=9 bytes_invalid=0 send_seq=211 receive_seq=211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999984 adj=63997719 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1393 bytes_read=19509 bytes_retransmit=9 bytes_invalid=0 send_seq=183 receive_seq=183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999459 adj=47997696 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1987 bytes_read=5759 bytes_retransmit=9 bytes_invalid=0 send_seq=178 receive_seq=178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999885 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=26.6 EBB42_Gen2_v1.0_T1: temp=26.0 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=690 bytes_read=23084 bytes_retransmit=0 bytes_invalid=0 send_seq=110 receive_seq=110 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999843 adj=31998657 coil_temp=18.0 refs=0 mcu_temp=21.10 supply_voltage=3.012 th0: temp=32.9 th1: temp=32.6 th2: temp=33.3 th3: temp=32.7 sysload=0.68 cputime=13.337 memavail=7430888 print_time=119.574 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 98.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=21488 bytes_read=29040 bytes_retransmit=9 bytes_invalid=0 send_seq=1389 receive_seq=1389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015050 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1240 bytes_read=5860 bytes_retransmit=0 bytes_invalid=0 send_seq=178 receive_seq=178 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999983 adj=49998164 toolboard_t0: mcu_awake=0.041 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=6523 bytes_read=19201 bytes_retransmit=9 bytes_invalid=0 send_seq=605 receive_seq=605 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000169 adj=63997748 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1780 bytes_read=11735 bytes_retransmit=9 bytes_invalid=0 send_seq=212 receive_seq=212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997709 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1399 bytes_read=19817 bytes_retransmit=9 bytes_invalid=0 send_seq=184 receive_seq=184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999458 adj=47997690 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1993 bytes_read=5775 bytes_retransmit=9 bytes_invalid=0 send_seq=179 receive_seq=179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999885 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=26.5 EBB42_Gen2_v1.0_T1: temp=26.0 raspberry_pi: temp=20.4  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=696 bytes_read=23429 bytes_retransmit=0 bytes_invalid=0 send_seq=111 receive_seq=111 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999843 adj=31998664 coil_temp=18.0 refs=0 mcu_temp=21.09 supply_voltage=3.012 th0: temp=33.3 th1: temp=32.6 th2: temp=33.5 th3: temp=32.9 sysload=0.68 cputime=13.441 memavail=7430888 print_time=120.574 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 99.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=23654 bytes_read=32113 bytes_retransmit=9 bytes_invalid=0 send_seq=1566 receive_seq=1566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015042 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1246 bytes_read=5875 bytes_retransmit=0 bytes_invalid=0 send_seq=179 receive_seq=179 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999982 adj=49998200 toolboard_t0: mcu_awake=0.041 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=8125 bytes_read=21842 bytes_retransmit=9 bytes_invalid=0 send_seq=739 receive_seq=739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000168 adj=63997755 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1786 bytes_read=11835 bytes_retransmit=9 bytes_invalid=0 send_seq=213 receive_seq=213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997681 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1405 bytes_read=20050 bytes_retransmit=9 bytes_invalid=0 send_seq=185 receive_seq=185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999458 adj=47997689 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1999 bytes_read=5791 bytes_retransmit=9 bytes_invalid=0 send_seq=180 receive_seq=180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999885 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=26.6 EBB42_Gen2_v1.0_T1: temp=25.8 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=702 bytes_read=23774 bytes_retransmit=0 bytes_invalid=0 send_seq=112 receive_seq=112 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999843 adj=31998666 coil_temp=18.0 refs=0 mcu_temp=21.08 supply_voltage=3.012 th0: temp=33.2 th1: temp=32.7 th2: temp=33.6 th3: temp=33.1 sysload=0.68 cputime=13.544 memavail=7430888 print_time=121.574 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 100.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=24902 bytes_read=33598 bytes_retransmit=9 bytes_invalid=0 send_seq=1658 receive_seq=1658 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015111 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1252 bytes_read=5904 bytes_retransmit=0 bytes_invalid=0 send_seq=180 receive_seq=180 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999981 adj=49998168 toolboard_t0: mcu_awake=0.041 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=8754 bytes_read=22909 bytes_retransmit=9 bytes_invalid=0 send_seq=791 receive_seq=791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000167 adj=63997763 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1830 bytes_read=11940 bytes_retransmit=9 bytes_invalid=0 send_seq=215 receive_seq=215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999981 adj=63997667 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1411 bytes_read=20283 bytes_retransmit=9 bytes_invalid=0 send_seq=186 receive_seq=186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999458 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2005 bytes_read=5807 bytes_retransmit=9 bytes_invalid=0 send_seq=181 receive_seq=181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999886 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=26.7 EBB42_Gen2_v1.0_T1: temp=26.0 raspberry_pi: temp=20.9  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=708 bytes_read=24126 bytes_retransmit=0 bytes_invalid=0 send_seq=113 receive_seq=113 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999843 adj=31998671 coil_temp=18.0 refs=0 mcu_temp=21.08 supply_voltage=3.012 th0: temp=34.0 th1: temp=32.8 th2: temp=34.1 th3: temp=33.1 sysload=0.68 cputime=13.622 memavail=7430892 print_time=122.576 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 101.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=26818 bytes_read=36236 bytes_retransmit=9 bytes_invalid=0 send_seq=1810 receive_seq=1810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015101 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1258 bytes_read=5920 bytes_retransmit=0 bytes_invalid=0 send_seq=181 receive_seq=181 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999980 adj=49998041 toolboard_t0: mcu_awake=0.041 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=8760 bytes_read=23037 bytes_retransmit=9 bytes_invalid=0 send_seq=792 receive_seq=792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000167 adj=63997620 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=3180 bytes_read=14196 bytes_retransmit=9 bytes_invalid=0 send_seq=328 receive_seq=328 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1417 bytes_read=20576 bytes_retransmit=9 bytes_invalid=0 send_seq=187 receive_seq=187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999459 adj=47997581 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2011 bytes_read=5823 bytes_retransmit=9 bytes_invalid=0 send_seq=182 receive_seq=182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999887 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=26.6 EBB42_Gen2_v1.0_T1: temp=26.0 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=714 bytes_read=24482 bytes_retransmit=0 bytes_invalid=0 send_seq=114 receive_seq=114 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999843 adj=31998593 coil_temp=18.0 refs=0 mcu_temp=21.08 supply_voltage=3.012 th0: temp=33.5 th1: temp=32.3 th2: temp=33.7 th3: temp=33.2 sysload=0.62 cputime=13.718 memavail=7430668 print_time=123.576 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 102.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=28967 bytes_read=39283 bytes_retransmit=9 bytes_invalid=0 send_seq=1985 receive_seq=1985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015095 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1264 bytes_read=5936 bytes_retransmit=0 bytes_invalid=0 send_seq=182 receive_seq=182 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999979 adj=49998033 toolboard_t0: mcu_awake=0.041 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=8766 bytes_read=23137 bytes_retransmit=9 bytes_invalid=0 send_seq=793 receive_seq=793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000167 adj=63997647 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=4782 bytes_read=16823 bytes_retransmit=9 bytes_invalid=0 send_seq=462 receive_seq=462 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999980 adj=63997515 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1423 bytes_read=20809 bytes_retransmit=9 bytes_invalid=0 send_seq=188 receive_seq=188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999459 adj=47997606 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2017 bytes_read=5850 bytes_retransmit=9 bytes_invalid=0 send_seq=183 receive_seq=183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999886 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=26.6 EBB42_Gen2_v1.0_T1: temp=25.9 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=720 bytes_read=24838 bytes_retransmit=0 bytes_invalid=0 send_seq=115 receive_seq=115 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999849 adj=31998605 coil_temp=18.0 refs=0 mcu_temp=21.08 supply_voltage=3.012 th0: temp=33.5 th1: temp=33.0 th2: temp=34.3 th3: temp=33.3 sysload=0.62 cputime=13.819 memavail=7430668 print_time=124.576 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.5 pwm=0.000
Stats 103.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=31118 bytes_read=42354 bytes_retransmit=9 bytes_invalid=0 send_seq=2159 receive_seq=2159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015086 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1270 bytes_read=5952 bytes_retransmit=0 bytes_invalid=0 send_seq=183 receive_seq=183 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999986 adj=49998052 toolboard_t0: mcu_awake=0.024 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=8772 bytes_read=23252 bytes_retransmit=9 bytes_invalid=0 send_seq=794 receive_seq=794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000167 adj=63997680 toolboard_t1: mcu_awake=0.041 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=6384 bytes_read=19480 bytes_retransmit=9 bytes_invalid=0 send_seq=596 receive_seq=596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999979 adj=63997518 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1429 bytes_read=21057 bytes_retransmit=9 bytes_invalid=0 send_seq=189 receive_seq=189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999458 adj=47997623 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2023 bytes_read=5866 bytes_retransmit=9 bytes_invalid=0 send_seq=184 receive_seq=184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999887 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=26.5 EBB42_Gen2_v1.0_T1: temp=26.2 raspberry_pi: temp=20.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=726 bytes_read=25194 bytes_retransmit=0 bytes_invalid=0 send_seq=116 receive_seq=116 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999848 adj=31998689 coil_temp=17.9 refs=0 mcu_temp=21.08 supply_voltage=3.012 th0: temp=33.7 th1: temp=32.8 th2: temp=34.6 th3: temp=33.2 sysload=0.62 cputime=13.920 memavail=7430668 print_time=125.576 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 104.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000002 mcu_task_stddev=0.000003 bytes_write=33267 bytes_read=45431 bytes_retransmit=9 bytes_invalid=0 send_seq=2334 receive_seq=2334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015078 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1276 bytes_read=5968 bytes_retransmit=0 bytes_invalid=0 send_seq=184 receive_seq=184 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999999 adj=49998154 toolboard_t0: mcu_awake=0.024 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=8778 bytes_read=23380 bytes_retransmit=9 bytes_invalid=0 send_seq=795 receive_seq=795 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000176 adj=63997717 toolboard_t1: mcu_awake=0.041 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=7993 bytes_read=22135 bytes_retransmit=9 bytes_invalid=0 send_seq=730 receive_seq=730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999979 adj=63997537 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1435 bytes_read=21350 bytes_retransmit=9 bytes_invalid=0 send_seq=190 receive_seq=190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999459 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2029 bytes_read=5882 bytes_retransmit=9 bytes_invalid=0 send_seq=185 receive_seq=185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999887 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=26.6 EBB42_Gen2_v1.0_T1: temp=26.0 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=732 bytes_read=25550 bytes_retransmit=0 bytes_invalid=0 send_seq=117 receive_seq=117 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999848 adj=31998669 coil_temp=17.9 refs=0 mcu_temp=21.08 supply_voltage=3.012 th0: temp=34.2 th1: temp=33.1 th2: temp=34.8 th3: temp=33.5 sysload=0.62 cputime=14.031 memavail=7430236 print_time=126.576 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.5 pwm=0.000
Stats 105.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000002 mcu_task_stddev=0.000003 bytes_write=35434 bytes_read=48499 bytes_retransmit=9 bytes_invalid=0 send_seq=2511 receive_seq=2511 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015128 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1288 bytes_read=6013 bytes_retransmit=0 bytes_invalid=0 send_seq=186 receive_seq=186 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000045 adj=49998318 toolboard_t0: mcu_awake=0.024 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=8790 bytes_read=23496 bytes_retransmit=9 bytes_invalid=0 send_seq=797 receive_seq=797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997858 toolboard_t1: mcu_awake=0.041 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=9596 bytes_read=24787 bytes_retransmit=9 bytes_invalid=0 send_seq=864 receive_seq=864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999979 adj=63997562 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1447 bytes_read=21599 bytes_retransmit=9 bytes_invalid=0 send_seq=192 receive_seq=192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999463 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2041 bytes_read=5914 bytes_retransmit=9 bytes_invalid=0 send_seq=187 receive_seq=187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999888 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=26.7 EBB42_Gen2_v1.0_T1: temp=26.0 raspberry_pi: temp=20.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=744 bytes_read=25922 bytes_retransmit=0 bytes_invalid=0 send_seq=119 receive_seq=119 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999846 adj=31998674 coil_temp=17.9 refs=0 mcu_temp=21.07 supply_voltage=3.012 th0: temp=34.1 th1: temp=32.8 th2: temp=34.6 th3: temp=33.8 sysload=0.62 cputime=14.140 memavail=7429984 print_time=127.576 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 106.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000002 mcu_task_stddev=0.000003 bytes_write=37331 bytes_read=50271 bytes_retransmit=9 bytes_invalid=0 send_seq=2624 receive_seq=2624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=0 freq=400015116 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1294 bytes_read=6029 bytes_retransmit=0 bytes_invalid=0 send_seq=187 receive_seq=187 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000073 adj=49998757 toolboard_t0: mcu_awake=0.024 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=8796 bytes_read=23596 bytes_retransmit=9 bytes_invalid=0 send_seq=798 receive_seq=798 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63998006 toolboard_t1: mcu_awake=0.041 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=10386 bytes_read=26106 bytes_retransmit=9 bytes_invalid=0 send_seq=930 receive_seq=930 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999979 adj=63997459 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1453 bytes_read=21832 bytes_retransmit=9 bytes_invalid=0 send_seq=193 receive_seq=193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999468 adj=47997630 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2047 bytes_read=5930 bytes_retransmit=9 bytes_invalid=0 send_seq=188 receive_seq=188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999888 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=26.4 EBB42_Gen2_v1.0_T1: temp=26.1 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=750 bytes_read=26278 bytes_retransmit=0 bytes_invalid=0 send_seq=120 receive_seq=120 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999846 adj=31998590 coil_temp=17.9 refs=0 mcu_temp=21.07 supply_voltage=3.012 th0: temp=34.7 th1: temp=33.1 th2: temp=34.7 th3: temp=33.6 sysload=0.57 cputime=14.234 memavail=7429984 print_time=129.300 buffer_time=0.901 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
RatOS:: Homing Z
Stats 107.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000002 mcu_task_stddev=0.000003 bytes_write=37959 bytes_read=50717 bytes_retransmit=9 bytes_invalid=0 send_seq=2652 receive_seq=2652 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015157 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1300 bytes_read=6045 bytes_retransmit=0 bytes_invalid=0 send_seq=188 receive_seq=188 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000107 adj=49998879 toolboard_t0: mcu_awake=0.024 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=8802 bytes_read=23724 bytes_retransmit=9 bytes_invalid=0 send_seq=799 receive_seq=799 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63998022 toolboard_t1: mcu_awake=0.041 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=10392 bytes_read=26234 bytes_retransmit=9 bytes_invalid=0 send_seq=931 receive_seq=931 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999985 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1459 bytes_read=22125 bytes_retransmit=9 bytes_invalid=0 send_seq=194 receive_seq=194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999467 adj=47997717 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2053 bytes_read=5957 bytes_retransmit=9 bytes_invalid=0 send_seq=189 receive_seq=189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999888 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=26.6 EBB42_Gen2_v1.0_T1: temp=26.1 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=811 bytes_read=26723 bytes_retransmit=0 bytes_invalid=0 send_seq=125 receive_seq=125 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999846 adj=31998620 coil_temp=17.9 refs=0 mcu_temp=21.05 supply_voltage=3.012 th0: temp=34.5 th1: temp=32.7 th2: temp=35.1 th3: temp=33.5 sysload=0.57 cputime=14.293 memavail=7429984 print_time=129.611 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 108.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000002 mcu_task_stddev=0.000003 bytes_write=40299 bytes_read=53299 bytes_retransmit=9 bytes_invalid=0 send_seq=2805 receive_seq=2804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015192 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1306 bytes_read=6061 bytes_retransmit=0 bytes_invalid=0 send_seq=189 receive_seq=189 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000141 adj=49999184 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=8808 bytes_read=23838 bytes_retransmit=9 bytes_invalid=0 send_seq=800 receive_seq=800 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63998053 toolboard_t1: mcu_awake=0.038 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=10398 bytes_read=26350 bytes_retransmit=9 bytes_invalid=0 send_seq=932 receive_seq=932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999988 adj=63997527 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1465 bytes_read=22373 bytes_retransmit=9 bytes_invalid=0 send_seq=195 receive_seq=195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999466 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2059 bytes_read=5973 bytes_retransmit=9 bytes_invalid=0 send_seq=190 receive_seq=190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999888 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=26.6 EBB42_Gen2_v1.0_T1: temp=26.1 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=2101 bytes_read=29140 bytes_retransmit=0 bytes_invalid=0 send_seq=233 receive_seq=233 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999846 adj=31998585 coil_temp=17.9 refs=0 mcu_temp=21.05 supply_voltage=3.012 th0: temp=34.7 th1: temp=32.8 th2: temp=35.0 th3: temp=33.6 sysload=0.57 cputime=14.387 memavail=7429984 print_time=130.611 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.5 pwm=0.000
Stats 109.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=42753 bytes_read=56381 bytes_retransmit=9 bytes_invalid=0 send_seq=2977 receive_seq=2977 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015227 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1312 bytes_read=6077 bytes_retransmit=0 bytes_invalid=0 send_seq=190 receive_seq=190 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000175 adj=49999314 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=8814 bytes_read=23938 bytes_retransmit=9 bytes_invalid=0 send_seq=801 receive_seq=801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997870 toolboard_t1: mcu_awake=0.038 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=10404 bytes_read=26450 bytes_retransmit=9 bytes_invalid=0 send_seq=933 receive_seq=933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999988 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1471 bytes_read=22606 bytes_retransmit=9 bytes_invalid=0 send_seq=196 receive_seq=196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999471 adj=47997582 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2065 bytes_read=5989 bytes_retransmit=9 bytes_invalid=0 send_seq=191 receive_seq=191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999890 adj=11999411 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=26.6 EBB42_Gen2_v1.0_T1: temp=26.1 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=3703 bytes_read=32023 bytes_retransmit=0 bytes_invalid=0 send_seq=367 receive_seq=367 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999845 adj=31998556 coil_temp=17.9 refs=0 mcu_temp=21.05 supply_voltage=3.012 th0: temp=34.9 th1: temp=32.8 th2: temp=35.0 th3: temp=34.0 sysload=0.57 cputime=14.489 memavail=7429984 print_time=131.611 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.5 pwm=0.000
Stats 110.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=45192 bytes_read=59412 bytes_retransmit=9 bytes_invalid=0 send_seq=3146 receive_seq=3146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015220 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1318 bytes_read=6106 bytes_retransmit=0 bytes_invalid=0 send_seq=191 receive_seq=191 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000211 adj=49999420 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=8820 bytes_read=24066 bytes_retransmit=9 bytes_invalid=0 send_seq=802 receive_seq=802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997736 toolboard_t1: mcu_awake=0.038 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=10410 bytes_read=26578 bytes_retransmit=9 bytes_invalid=0 send_seq=934 receive_seq=934 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999987 adj=63997442 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1477 bytes_read=22899 bytes_retransmit=9 bytes_invalid=0 send_seq=197 receive_seq=197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999470 adj=47997601 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2071 bytes_read=6005 bytes_retransmit=9 bytes_invalid=0 send_seq=192 receive_seq=192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999890 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=26.8 EBB42_Gen2_v1.0_T1: temp=26.1 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=5317 bytes_read=34911 bytes_retransmit=0 bytes_invalid=0 send_seq=502 receive_seq=502 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999845 adj=31998534 coil_temp=17.9 refs=0 mcu_temp=21.05 supply_voltage=3.012 th0: temp=35.0 th1: temp=32.8 th2: temp=35.4 th3: temp=34.2 sysload=0.57 cputime=14.595 memavail=7429992 print_time=132.611 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 111.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=47678 bytes_read=62469 bytes_retransmit=9 bytes_invalid=0 send_seq=3323 receive_seq=3323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015256 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1324 bytes_read=6122 bytes_retransmit=0 bytes_invalid=0 send_seq=192 receive_seq=192 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000249 adj=49999597 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=8826 bytes_read=24159 bytes_retransmit=9 bytes_invalid=0 send_seq=803 receive_seq=803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997711 toolboard_t1: mcu_awake=0.038 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=10416 bytes_read=26671 bytes_retransmit=9 bytes_invalid=0 send_seq=935 receive_seq=935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999986 adj=63997469 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1483 bytes_read=23132 bytes_retransmit=9 bytes_invalid=0 send_seq=198 receive_seq=198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999470 adj=47997711 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2077 bytes_read=6021 bytes_retransmit=9 bytes_invalid=0 send_seq=193 receive_seq=193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999889 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=26.9 EBB42_Gen2_v1.0_T1: temp=26.2 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=6919 bytes_read=37808 bytes_retransmit=0 bytes_invalid=0 send_seq=636 receive_seq=636 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999845 adj=31998561 coil_temp=17.9 refs=0 mcu_temp=21.05 supply_voltage=3.011 th0: temp=35.3 th1: temp=32.9 th2: temp=35.4 th3: temp=34.0 sysload=0.53 cputime=14.707 memavail=7430528 print_time=133.611 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.5 pwm=0.000
Stats 112.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=50147 bytes_read=65559 bytes_retransmit=9 bytes_invalid=0 send_seq=3498 receive_seq=3498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015280 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1330 bytes_read=6138 bytes_retransmit=0 bytes_invalid=0 send_seq=193 receive_seq=193 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000287 adj=49999711 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=8832 bytes_read=24252 bytes_retransmit=9 bytes_invalid=0 send_seq=804 receive_seq=804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997623 toolboard_t1: mcu_awake=0.038 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=10422 bytes_read=26764 bytes_retransmit=9 bytes_invalid=0 send_seq=936 receive_seq=936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63997405 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1489 bytes_read=23365 bytes_retransmit=9 bytes_invalid=0 send_seq=199 receive_seq=199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999470 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2083 bytes_read=6048 bytes_retransmit=9 bytes_invalid=0 send_seq=194 receive_seq=194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999889 adj=11999422 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=26.8 EBB42_Gen2_v1.0_T1: temp=26.1 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=8533 bytes_read=40696 bytes_retransmit=0 bytes_invalid=0 send_seq=771 receive_seq=771 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999845 adj=31998537 coil_temp=17.9 refs=0 mcu_temp=21.05 supply_voltage=3.012 th0: temp=35.4 th1: temp=33.0 th2: temp=35.4 th3: temp=34.1 sysload=0.53 cputime=14.812 memavail=7430528 print_time=134.611 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 113.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=52606 bytes_read=68596 bytes_retransmit=9 bytes_invalid=0 send_seq=3671 receive_seq=3671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015303 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1336 bytes_read=6154 bytes_retransmit=0 bytes_invalid=0 send_seq=194 receive_seq=194 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000330 adj=49999812 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=8838 bytes_read=24385 bytes_retransmit=9 bytes_invalid=0 send_seq=805 receive_seq=805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997587 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=10428 bytes_read=26897 bytes_retransmit=9 bytes_invalid=0 send_seq=937 receive_seq=937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999988 adj=63997426 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1495 bytes_read=23673 bytes_retransmit=9 bytes_invalid=0 send_seq=200 receive_seq=200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999469 adj=47997598 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2089 bytes_read=6064 bytes_retransmit=9 bytes_invalid=0 send_seq=195 receive_seq=195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999889 adj=11999418 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=26.9 EBB42_Gen2_v1.0_T1: temp=26.0 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=10135 bytes_read=43593 bytes_retransmit=0 bytes_invalid=0 send_seq=905 receive_seq=905 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999851 adj=31998537 coil_temp=17.9 refs=0 mcu_temp=21.05 supply_voltage=3.012 th0: temp=35.8 th1: temp=33.2 th2: temp=35.1 th3: temp=34.2 sysload=0.53 cputime=14.934 memavail=7425244 print_time=135.611 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 114.0: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000002 mcu_task_stddev=0.000003 bytes_write=55042 bytes_read=71619 bytes_retransmit=9 bytes_invalid=0 send_seq=3838 receive_seq=3838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015282 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1342 bytes_read=6170 bytes_retransmit=0 bytes_invalid=0 send_seq=195 receive_seq=195 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000366 adj=49999970 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=8844 bytes_read=24478 bytes_retransmit=9 bytes_invalid=0 send_seq=806 receive_seq=806 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997555 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=10434 bytes_read=26990 bytes_retransmit=9 bytes_invalid=0 send_seq=938 receive_seq=938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999991 adj=63997394 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1501 bytes_read=23906 bytes_retransmit=9 bytes_invalid=0 send_seq=201 receive_seq=201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999468 adj=47997561 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2095 bytes_read=6080 bytes_retransmit=9 bytes_invalid=0 send_seq=196 receive_seq=196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999892 adj=11999410 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=26.9 EBB42_Gen2_v1.0_T1: temp=26.2 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=11749 bytes_read=46476 bytes_retransmit=0 bytes_invalid=0 send_seq=1040 receive_seq=1039 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999852 adj=31998611 coil_temp=17.9 refs=0 mcu_temp=21.05 supply_voltage=3.012 th0: temp=35.7 th1: temp=33.1 th2: temp=35.7 th3: temp=34.5 sysload=0.53 cputime=15.044 memavail=7430804 print_time=136.611 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 115.0: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000002 mcu_task_stddev=0.000003 bytes_write=57511 bytes_read=74709 bytes_retransmit=9 bytes_invalid=0 send_seq=4013 receive_seq=4013 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015353 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1348 bytes_read=6186 bytes_retransmit=0 bytes_invalid=0 send_seq=196 receive_seq=196 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000402 adj=50000094 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=8850 bytes_read=24576 bytes_retransmit=9 bytes_invalid=0 send_seq=807 receive_seq=807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997675 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=10440 bytes_read=27088 bytes_retransmit=9 bytes_invalid=0 send_seq=939 receive_seq=939 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999990 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1507 bytes_read=24139 bytes_retransmit=9 bytes_invalid=0 send_seq=202 receive_seq=202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999471 adj=47997601 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2101 bytes_read=6096 bytes_retransmit=9 bytes_invalid=0 send_seq=197 receive_seq=197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999892 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=26.8 EBB42_Gen2_v1.0_T1: temp=26.3 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=13351 bytes_read=49364 bytes_retransmit=0 bytes_invalid=0 send_seq=1174 receive_seq=1174 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999852 adj=31998652 coil_temp=17.9 refs=0 mcu_temp=21.05 supply_voltage=3.012 th0: temp=36.1 th1: temp=32.9 th2: temp=36.0 th3: temp=34.0 sysload=0.53 cputime=15.147 memavail=7430912 print_time=137.611 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.5 pwm=0.000
Stats 116.0: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000002 mcu_task_stddev=0.000003 bytes_write=58568 bytes_read=75657 bytes_retransmit=9 bytes_invalid=0 send_seq=4071 receive_seq=4071 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015385 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1354 bytes_read=6215 bytes_retransmit=0 bytes_invalid=0 send_seq=197 receive_seq=197 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000439 adj=50000032 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=8856 bytes_read=24704 bytes_retransmit=9 bytes_invalid=0 send_seq=808 receive_seq=808 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997514 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=10446 bytes_read=27216 bytes_retransmit=9 bytes_invalid=0 send_seq=940 receive_seq=940 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999990 adj=63997368 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1513 bytes_read=24432 bytes_retransmit=9 bytes_invalid=0 send_seq=203 receive_seq=203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999472 adj=47997541 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2107 bytes_read=6112 bytes_retransmit=9 bytes_invalid=0 send_seq=198 receive_seq=198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999892 adj=11999423 Octopus_Pro_H723_V1.1: temp=28.0 EBB42_Gen2_v1.0_T0: temp=26.9 EBB42_Gen2_v1.0_T1: temp=26.4 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=13583 bytes_read=52405 bytes_retransmit=0 bytes_invalid=0 send_seq=1196 receive_seq=1196 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999851 adj=31998569 coil_temp=17.9 refs=1 mcu_temp=21.05 supply_voltage=3.012 th0: temp=36.3 th1: temp=33.1 th2: temp=36.2 th3: temp=34.7 sysload=0.57 cputime=15.346 memavail=7430420 print_time=138.519 buffer_time=0.114 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 117.0: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000002 mcu_task_stddev=0.000003 bytes_write=59167 bytes_read=76105 bytes_retransmit=9 bytes_invalid=0 send_seq=4099 receive_seq=4099 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015411 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1360 bytes_read=6231 bytes_retransmit=0 bytes_invalid=0 send_seq=198 receive_seq=198 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000483 adj=50000072 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=8862 bytes_read=24804 bytes_retransmit=9 bytes_invalid=0 send_seq=809 receive_seq=809 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997481 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=10452 bytes_read=27316 bytes_retransmit=9 bytes_invalid=0 send_seq=941 receive_seq=941 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999991 adj=63997340 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1519 bytes_read=24665 bytes_retransmit=9 bytes_invalid=0 send_seq=204 receive_seq=204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999471 adj=47997523 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2113 bytes_read=6139 bytes_retransmit=9 bytes_invalid=0 send_seq=199 receive_seq=199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999892 adj=11999411 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.0 EBB42_Gen2_v1.0_T1: temp=26.3 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=13596 bytes_read=53163 bytes_retransmit=0 bytes_invalid=0 send_seq=1198 receive_seq=1198 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999850 adj=31998543 coil_temp=17.9 refs=0 mcu_temp=21.05 supply_voltage=3.012 th0: temp=36.4 th1: temp=33.7 th2: temp=36.2 th3: temp=34.5 sysload=0.57 cputime=15.416 memavail=7430600 print_time=139.789 buffer_time=0.383 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 118.0: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000002 mcu_task_stddev=0.000003 bytes_write=59674 bytes_read=76575 bytes_retransmit=9 bytes_invalid=0 send_seq=4126 receive_seq=4126 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015382 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1366 bytes_read=6247 bytes_retransmit=0 bytes_invalid=0 send_seq=199 receive_seq=199 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000529 adj=50000160 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=8868 bytes_read=24904 bytes_retransmit=9 bytes_invalid=0 send_seq=810 receive_seq=810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997493 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=10458 bytes_read=27416 bytes_retransmit=9 bytes_invalid=0 send_seq=942 receive_seq=942 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999992 adj=63997352 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1525 bytes_read=24913 bytes_retransmit=9 bytes_invalid=0 send_seq=205 receive_seq=205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999471 adj=47997500 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2119 bytes_read=6155 bytes_retransmit=9 bytes_invalid=0 send_seq=200 receive_seq=200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999892 adj=11999409 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=26.9 EBB42_Gen2_v1.0_T1: temp=26.4 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=13602 bytes_read=53519 bytes_retransmit=0 bytes_invalid=0 send_seq=1199 receive_seq=1199 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999854 adj=31998525 coil_temp=17.9 refs=0 mcu_temp=21.05 supply_voltage=3.012 th0: temp=36.7 th1: temp=33.0 th2: temp=36.0 th3: temp=34.7 sysload=0.57 cputime=15.459 memavail=7430600 print_time=139.789 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 119.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=59967 bytes_read=77010 bytes_retransmit=9 bytes_invalid=0 send_seq=4148 receive_seq=4148 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015429 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1372 bytes_read=6263 bytes_retransmit=0 bytes_invalid=0 send_seq=200 receive_seq=200 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000560 adj=50000573 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=8874 bytes_read=25046 bytes_retransmit=9 bytes_invalid=0 send_seq=811 receive_seq=811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997569 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=10464 bytes_read=27558 bytes_retransmit=9 bytes_invalid=0 send_seq=943 receive_seq=943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999994 adj=63997452 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1531 bytes_read=25206 bytes_retransmit=9 bytes_invalid=0 send_seq=206 receive_seq=206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999472 adj=47997558 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2125 bytes_read=6171 bytes_retransmit=9 bytes_invalid=0 send_seq=201 receive_seq=201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999891 adj=11999420 Octopus_Pro_H723_V1.1: temp=28.0 EBB42_Gen2_v1.0_T0: temp=26.8 EBB42_Gen2_v1.0_T1: temp=26.1 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=13608 bytes_read=53875 bytes_retransmit=0 bytes_invalid=0 send_seq=1200 receive_seq=1200 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999860 adj=31998614 coil_temp=17.9 refs=0 mcu_temp=21.05 supply_voltage=3.012 th0: temp=36.8 th1: temp=33.8 th2: temp=35.9 th3: temp=34.7 sysload=0.57 cputime=15.503 memavail=7430600 print_time=139.789 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 120.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=60265 bytes_read=77435 bytes_retransmit=9 bytes_invalid=0 send_seq=4171 receive_seq=4171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015446 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1378 bytes_read=6279 bytes_retransmit=0 bytes_invalid=0 send_seq=201 receive_seq=201 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000590 adj=50000418 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=8880 bytes_read=25146 bytes_retransmit=9 bytes_invalid=0 send_seq=812 receive_seq=812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997481 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=10470 bytes_read=27658 bytes_retransmit=9 bytes_invalid=0 send_seq=944 receive_seq=944 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997394 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1537 bytes_read=25439 bytes_retransmit=9 bytes_invalid=0 send_seq=207 receive_seq=207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999479 adj=47997520 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2131 bytes_read=6187 bytes_retransmit=9 bytes_invalid=0 send_seq=202 receive_seq=202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999891 adj=11999400 Octopus_Pro_H723_V1.1: temp=27.9 EBB42_Gen2_v1.0_T0: temp=26.9 EBB42_Gen2_v1.0_T1: temp=26.0 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=13614 bytes_read=54231 bytes_retransmit=0 bytes_invalid=0 send_seq=1201 receive_seq=1201 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999859 adj=31998649 coil_temp=17.9 refs=0 mcu_temp=21.05 supply_voltage=3.012 th0: temp=37.3 th1: temp=33.4 th2: temp=36.9 th3: temp=34.9 sysload=0.57 cputime=15.545 memavail=7430600 print_time=139.789 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 121.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=60563 bytes_read=77889 bytes_retransmit=9 bytes_invalid=0 send_seq=4194 receive_seq=4194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015417 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1384 bytes_read=6308 bytes_retransmit=0 bytes_invalid=0 send_seq=202 receive_seq=202 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000618 adj=50000330 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=8886 bytes_read=25246 bytes_retransmit=9 bytes_invalid=0 send_seq=813 receive_seq=813 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997490 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=10476 bytes_read=27758 bytes_retransmit=9 bytes_invalid=0 send_seq=945 receive_seq=945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997545 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1543 bytes_read=25672 bytes_retransmit=9 bytes_invalid=0 send_seq=208 receive_seq=208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999478 adj=47997611 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2137 bytes_read=6203 bytes_retransmit=9 bytes_invalid=0 send_seq=203 receive_seq=203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999891 adj=11999397 Octopus_Pro_H723_V1.1: temp=28.0 EBB42_Gen2_v1.0_T0: temp=26.9 EBB42_Gen2_v1.0_T1: temp=26.4 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=13620 bytes_read=54587 bytes_retransmit=0 bytes_invalid=0 send_seq=1202 receive_seq=1202 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999857 adj=31998607 coil_temp=17.9 refs=0 mcu_temp=21.05 supply_voltage=3.012 th0: temp=37.1 th1: temp=33.4 th2: temp=36.4 th3: temp=34.9 sysload=0.60 cputime=15.587 memavail=7430600 print_time=139.789 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.5 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 122.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=63538 bytes_read=78529 bytes_retransmit=9 bytes_invalid=0 send_seq=4260 receive_seq=4260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015414 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1390 bytes_read=6324 bytes_retransmit=0 bytes_invalid=0 send_seq=203 receive_seq=203 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000647 adj=50000345 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=8892 bytes_read=25374 bytes_retransmit=9 bytes_invalid=0 send_seq=814 receive_seq=814 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997608 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=10482 bytes_read=27886 bytes_retransmit=9 bytes_invalid=0 send_seq=946 receive_seq=946 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000001 adj=63997569 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1549 bytes_read=25965 bytes_retransmit=9 bytes_invalid=0 send_seq=209 receive_seq=209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999476 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2143 bytes_read=6230 bytes_retransmit=9 bytes_invalid=0 send_seq=204 receive_seq=204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999890 adj=11999413 Octopus_Pro_H723_V1.1: temp=28.0 EBB42_Gen2_v1.0_T0: temp=27.0 EBB42_Gen2_v1.0_T1: temp=26.3 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=13633 bytes_read=55804 bytes_retransmit=0 bytes_invalid=0 send_seq=1204 receive_seq=1204 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999855 adj=31998618 coil_temp=17.9 refs=3 mcu_temp=21.04 supply_voltage=3.012 th0: temp=37.2 th1: temp=33.4 th2: temp=36.9 th3: temp=35.0 sysload=0.60 cputime=15.723 memavail=7430600 print_time=145.119 buffer_time=0.711 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 123.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=65086 bytes_read=79069 bytes_retransmit=9 bytes_invalid=0 send_seq=4306 receive_seq=4306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015405 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1396 bytes_read=6340 bytes_retransmit=0 bytes_invalid=0 send_seq=204 receive_seq=204 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000673 adj=50000033 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=8898 bytes_read=25474 bytes_retransmit=9 bytes_invalid=0 send_seq=815 receive_seq=815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997668 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=10488 bytes_read=27986 bytes_retransmit=9 bytes_invalid=0 send_seq=947 receive_seq=947 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000008 adj=63997541 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1555 bytes_read=26213 bytes_retransmit=9 bytes_invalid=0 send_seq=210 receive_seq=210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999475 adj=47997623 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2149 bytes_read=6246 bytes_retransmit=9 bytes_invalid=0 send_seq=205 receive_seq=205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999890 adj=11999417 Octopus_Pro_H723_V1.1: temp=28.0 EBB42_Gen2_v1.0_T0: temp=27.2 EBB42_Gen2_v1.0_T1: temp=26.4 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=13685 bytes_read=58895 bytes_retransmit=0 bytes_invalid=0 send_seq=1208 receive_seq=1208 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999854 adj=31998601 coil_temp=17.9 refs=2 mcu_temp=21.03 supply_voltage=3.012 th0: temp=37.5 th1: temp=33.5 th2: temp=36.9 th3: temp=34.7 sysload=0.60 cputime=15.894 memavail=7430600 print_time=145.598 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 124.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=67550 bytes_read=82155 bytes_retransmit=9 bytes_invalid=0 send_seq=4480 receive_seq=4480 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015376 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1402 bytes_read=6356 bytes_retransmit=0 bytes_invalid=0 send_seq=205 receive_seq=205 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000697 adj=50000240 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=8904 bytes_read=25588 bytes_retransmit=9 bytes_invalid=0 send_seq=816 receive_seq=816 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997717 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10494 bytes_read=28100 bytes_retransmit=9 bytes_invalid=0 send_seq=948 receive_seq=948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997653 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1561 bytes_read=26446 bytes_retransmit=9 bytes_invalid=0 send_seq=211 receive_seq=211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999475 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2155 bytes_read=6262 bytes_retransmit=9 bytes_invalid=0 send_seq=206 receive_seq=206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999890 adj=11999419 Octopus_Pro_H723_V1.1: temp=28.0 EBB42_Gen2_v1.0_T0: temp=26.9 EBB42_Gen2_v1.0_T1: temp=26.4 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=15275 bytes_read=64507 bytes_retransmit=0 bytes_invalid=0 send_seq=1341 receive_seq=1341 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999854 adj=31998603 coil_temp=17.9 refs=2 mcu_temp=21.03 supply_voltage=3.012 th0: temp=37.4 th1: temp=33.7 th2: temp=36.7 th3: temp=35.3 sysload=0.60 cputime=16.107 memavail=7432756 print_time=146.598 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
probe at 20.000,9.999,4.245 is z=1.958416
Stats 125.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=70605 bytes_read=83180 bytes_retransmit=9 bytes_invalid=0 send_seq=4563 receive_seq=4563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015373 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1408 bytes_read=6372 bytes_retransmit=0 bytes_invalid=0 send_seq=206 receive_seq=206 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000721 adj=50000249 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=8910 bytes_read=25716 bytes_retransmit=9 bytes_invalid=0 send_seq=817 receive_seq=817 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997751 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10500 bytes_read=28228 bytes_retransmit=9 bytes_invalid=0 send_seq=949 receive_seq=949 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000002 adj=63997650 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1567 bytes_read=26739 bytes_retransmit=9 bytes_invalid=0 send_seq=212 receive_seq=212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999474 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2161 bytes_read=6278 bytes_retransmit=9 bytes_invalid=0 send_seq=207 receive_seq=207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999890 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.1 EBB42_Gen2_v1.0_T1: temp=26.4 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=15471 bytes_read=67884 bytes_retransmit=0 bytes_invalid=0 send_seq=1359 receive_seq=1359 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999852 adj=31998629 coil_temp=17.9 refs=3 mcu_temp=21.03 supply_voltage=3.012 th0: temp=37.7 th1: temp=33.8 th2: temp=36.6 th3: temp=35.6 sysload=0.60 cputime=16.348 memavail=7432756 print_time=148.515 buffer_time=1.106 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.5 pwm=0.000
Stats 126.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=71621 bytes_read=83665 bytes_retransmit=9 bytes_invalid=0 send_seq=4598 receive_seq=4598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015356 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1414 bytes_read=6401 bytes_retransmit=0 bytes_invalid=0 send_seq=207 receive_seq=207 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000742 adj=49999875 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=8916 bytes_read=25816 bytes_retransmit=9 bytes_invalid=0 send_seq=818 receive_seq=818 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997717 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10506 bytes_read=28328 bytes_retransmit=9 bytes_invalid=0 send_seq=950 receive_seq=950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000000 adj=63997566 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1573 bytes_read=26972 bytes_retransmit=9 bytes_invalid=0 send_seq=213 receive_seq=213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999472 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2167 bytes_read=6294 bytes_retransmit=9 bytes_invalid=0 send_seq=208 receive_seq=208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999890 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=26.9 EBB42_Gen2_v1.0_T1: temp=26.4 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=15477 bytes_read=70960 bytes_retransmit=0 bytes_invalid=0 send_seq=1360 receive_seq=1360 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999853 adj=31998616 coil_temp=17.9 refs=3 mcu_temp=21.02 supply_voltage=3.012 th0: temp=37.3 th1: temp=33.5 th2: temp=36.3 th3: temp=35.1 sysload=0.55 cputime=16.517 memavail=7432756 print_time=148.515 buffer_time=0.105 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.5 pwm=0.000
Stats 127.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=73590 bytes_read=85743 bytes_retransmit=9 bytes_invalid=0 send_seq=4720 receive_seq=4719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015361 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1420 bytes_read=6417 bytes_retransmit=0 bytes_invalid=0 send_seq=208 receive_seq=208 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000761 adj=50000157 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=8922 bytes_read=25916 bytes_retransmit=9 bytes_invalid=0 send_seq=819 receive_seq=819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997748 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10512 bytes_read=28428 bytes_retransmit=9 bytes_invalid=0 send_seq=951 receive_seq=951 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000002 adj=63997569 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1579 bytes_read=27205 bytes_retransmit=9 bytes_invalid=0 send_seq=214 receive_seq=214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999473 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2173 bytes_read=6321 bytes_retransmit=9 bytes_invalid=0 send_seq=209 receive_seq=209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999890 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=26.9 EBB42_Gen2_v1.0_T1: temp=26.2 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=16489 bytes_read=75585 bytes_retransmit=0 bytes_invalid=0 send_seq=1444 receive_seq=1444 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999853 adj=31998642 coil_temp=17.8 refs=2 mcu_temp=21.01 supply_voltage=3.012 th0: temp=37.6 th1: temp=34.1 th2: temp=37.1 th3: temp=35.3 sysload=0.55 cputime=16.708 memavail=7432756 print_time=149.629 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 128.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=76052 bytes_read=88832 bytes_retransmit=9 bytes_invalid=0 send_seq=4900 receive_seq=4900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015376 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1426 bytes_read=6433 bytes_retransmit=0 bytes_invalid=0 send_seq=209 receive_seq=209 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000780 adj=50000094 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=8928 bytes_read=26044 bytes_retransmit=9 bytes_invalid=0 send_seq=820 receive_seq=820 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997720 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10518 bytes_read=28556 bytes_retransmit=9 bytes_invalid=0 send_seq=952 receive_seq=952 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999999 adj=63997581 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1585 bytes_read=27513 bytes_retransmit=9 bytes_invalid=0 send_seq=215 receive_seq=215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999472 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2179 bytes_read=6337 bytes_retransmit=9 bytes_invalid=0 send_seq=210 receive_seq=210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999890 adj=11999431 Octopus_Pro_H723_V1.1: temp=27.9 EBB42_Gen2_v1.0_T0: temp=26.9 EBB42_Gen2_v1.0_T1: temp=26.6 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=18065 bytes_read=81175 bytes_retransmit=0 bytes_invalid=0 send_seq=1577 receive_seq=1577 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999852 adj=31998628 coil_temp=17.8 refs=3 mcu_temp=20.99 supply_voltage=3.012 th0: temp=37.3 th1: temp=34.5 th2: temp=37.0 th3: temp=35.4 sysload=0.55 cputime=16.929 memavail=7432784 print_time=150.819 buffer_time=0.408 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
probe at 480.000,230.001,-3.111 is z=1.957374
Stats 129.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=77901 bytes_read=89398 bytes_retransmit=9 bytes_invalid=0 send_seq=4948 receive_seq=4948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015355 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1432 bytes_read=6449 bytes_retransmit=0 bytes_invalid=0 send_seq=210 receive_seq=210 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000799 adj=49999952 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=8934 bytes_read=26158 bytes_retransmit=9 bytes_invalid=0 send_seq=821 receive_seq=821 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997670 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10524 bytes_read=28670 bytes_retransmit=9 bytes_invalid=0 send_seq=953 receive_seq=953 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997502 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1591 bytes_read=27746 bytes_retransmit=9 bytes_invalid=0 send_seq=216 receive_seq=216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999471 adj=47997603 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2185 bytes_read=6353 bytes_retransmit=9 bytes_invalid=0 send_seq=211 receive_seq=211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999890 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.0 EBB42_Gen2_v1.0_T0: temp=27.0 EBB42_Gen2_v1.0_T1: temp=26.2 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=18071 bytes_read=84251 bytes_retransmit=0 bytes_invalid=0 send_seq=1578 receive_seq=1578 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999851 adj=31998598 coil_temp=17.8 refs=3 mcu_temp=20.99 supply_voltage=3.012 th0: temp=37.6 th1: temp=34.6 th2: temp=37.4 th3: temp=35.7 sysload=0.55 cputime=17.147 memavail=7432784 print_time=152.543 buffer_time=1.132 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 130.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=78723 bytes_read=89897 bytes_retransmit=9 bytes_invalid=0 send_seq=4980 receive_seq=4980 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015347 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1438 bytes_read=6465 bytes_retransmit=0 bytes_invalid=0 send_seq=211 receive_seq=211 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000816 adj=49999781 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=8940 bytes_read=26258 bytes_retransmit=9 bytes_invalid=0 send_seq=822 receive_seq=822 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997727 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10530 bytes_read=28770 bytes_retransmit=9 bytes_invalid=0 send_seq=954 receive_seq=954 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999996 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1597 bytes_read=27979 bytes_retransmit=9 bytes_invalid=0 send_seq=217 receive_seq=217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999473 adj=47997634 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2191 bytes_read=6369 bytes_retransmit=9 bytes_invalid=0 send_seq=212 receive_seq=212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999889 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.1 EBB42_Gen2_v1.0_T1: temp=26.4 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=18077 bytes_read=87327 bytes_retransmit=0 bytes_invalid=0 send_seq=1579 receive_seq=1579 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999851 adj=31998627 coil_temp=17.8 refs=3 mcu_temp=20.99 supply_voltage=3.012 th0: temp=37.6 th1: temp=34.1 th2: temp=36.6 th3: temp=35.2 sysload=0.55 cputime=17.314 memavail=7432532 print_time=152.543 buffer_time=0.131 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 131.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=80632 bytes_read=91880 bytes_retransmit=9 bytes_invalid=0 send_seq=5099 receive_seq=5099 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015354 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1444 bytes_read=6494 bytes_retransmit=0 bytes_invalid=0 send_seq=212 receive_seq=212 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000830 adj=50000003 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=8946 bytes_read=26386 bytes_retransmit=9 bytes_invalid=0 send_seq=823 receive_seq=823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997735 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10536 bytes_read=28898 bytes_retransmit=9 bytes_invalid=0 send_seq=955 receive_seq=955 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997533 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1603 bytes_read=28272 bytes_retransmit=9 bytes_invalid=0 send_seq=218 receive_seq=218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999475 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2197 bytes_read=6385 bytes_retransmit=9 bytes_invalid=0 send_seq=213 receive_seq=213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999889 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.0 EBB42_Gen2_v1.0_T0: temp=27.1 EBB42_Gen2_v1.0_T1: temp=26.3 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=19041 bytes_read=91890 bytes_retransmit=0 bytes_invalid=0 send_seq=1659 receive_seq=1659 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999850 adj=31998628 coil_temp=17.8 refs=2 mcu_temp=20.99 supply_voltage=3.012 th0: temp=38.0 th1: temp=34.1 th2: temp=37.1 th3: temp=35.6 sysload=0.59 cputime=17.510 memavail=7433672 print_time=153.621 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
probe at 20.000,449.999,8.989 is z=1.961944
Calculating bed tilt with: [[19.999999996616697, 9.998593750412038, 4.286584270764401], [479.9999999966214, 230.00078125003796, -3.0686238433194335], [19.99999999689345, 449.9993750026889, 9.026805655936114]]
Coordinate descent initial error: 80.2954130186692
Coordinate descent best_err: 2.722153886444409e-10  rounds: 209
Calculated bed tilt parameters: {'x_adjust': -0.0211420733155081, 'y_adjust': 0.01077323185219073, 'z_adjust': 4.601714058257722}
Making the following Z adjustments:
stepper_z = 2.305450
stepper_z1 = 2.406548
stepper_z2 = -8.265586
Retries: 0/10 Probed points range: 12.095429 tolerance: 0.020000
Stats 132.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=84922 bytes_read=93291 bytes_retransmit=9 bytes_invalid=0 send_seq=5220 receive_seq=5220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=0 freq=400015375 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1450 bytes_read=6510 bytes_retransmit=0 bytes_invalid=0 send_seq=213 receive_seq=213 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000844 adj=49999934 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=8952 bytes_read=26486 bytes_retransmit=9 bytes_invalid=0 send_seq=824 receive_seq=824 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997718 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10542 bytes_read=28998 bytes_retransmit=9 bytes_invalid=0 send_seq=956 receive_seq=956 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999994 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1609 bytes_read=28505 bytes_retransmit=9 bytes_invalid=0 send_seq=219 receive_seq=219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999474 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2203 bytes_read=6412 bytes_retransmit=9 bytes_invalid=0 send_seq=214 receive_seq=214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999889 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.1 EBB42_Gen2_v1.0_T1: temp=26.4 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=19405 bytes_read=95533 bytes_retransmit=0 bytes_invalid=0 send_seq=1691 receive_seq=1691 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999850 adj=31998612 coil_temp=17.8 refs=3 mcu_temp=20.99 supply_voltage=3.012 th0: temp=37.7 th1: temp=34.5 th2: temp=37.4 th3: temp=35.7 sysload=0.59 cputime=17.785 memavail=7433672 print_time=155.868 buffer_time=1.455 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 133.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=85234 bytes_read=93745 bytes_retransmit=9 bytes_invalid=0 send_seq=5243 receive_seq=5243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015382 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1456 bytes_read=6526 bytes_retransmit=0 bytes_invalid=0 send_seq=214 receive_seq=214 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000856 adj=49999524 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=8958 bytes_read=26586 bytes_retransmit=9 bytes_invalid=0 send_seq=825 receive_seq=825 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997722 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10548 bytes_read=29098 bytes_retransmit=9 bytes_invalid=0 send_seq=957 receive_seq=957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999992 adj=63997467 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1615 bytes_read=28753 bytes_retransmit=9 bytes_invalid=0 send_seq=220 receive_seq=220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999473 adj=47997600 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2209 bytes_read=6428 bytes_retransmit=9 bytes_invalid=0 send_seq=215 receive_seq=215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999889 adj=11999420 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=26.8 EBB42_Gen2_v1.0_T1: temp=26.3 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=19411 bytes_read=98609 bytes_retransmit=0 bytes_invalid=0 send_seq=1692 receive_seq=1692 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999850 adj=31998589 coil_temp=17.8 refs=3 mcu_temp=20.98 supply_voltage=3.012 th0: temp=37.1 th1: temp=34.3 th2: temp=36.6 th3: temp=35.3 sysload=0.59 cputime=17.954 memavail=7433672 print_time=155.868 buffer_time=0.454 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 134.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=87459 bytes_read=94987 bytes_retransmit=9 bytes_invalid=0 send_seq=5331 receive_seq=5331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015362 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1462 bytes_read=6542 bytes_retransmit=0 bytes_invalid=0 send_seq=215 receive_seq=215 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000866 adj=49999675 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=8964 bytes_read=26728 bytes_retransmit=9 bytes_invalid=0 send_seq=826 receive_seq=826 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997696 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10554 bytes_read=29240 bytes_retransmit=9 bytes_invalid=0 send_seq=958 receive_seq=958 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999991 adj=63997417 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1621 bytes_read=29046 bytes_retransmit=9 bytes_invalid=0 send_seq=221 receive_seq=221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999474 adj=47997575 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2215 bytes_read=6444 bytes_retransmit=9 bytes_invalid=0 send_seq=216 receive_seq=216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999889 adj=11999416 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.1 EBB42_Gen2_v1.0_T1: temp=26.5 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=19859 bytes_read=102355 bytes_retransmit=0 bytes_invalid=0 send_seq=1729 receive_seq=1729 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999850 adj=31998585 coil_temp=17.8 refs=2 mcu_temp=20.98 supply_voltage=3.012 th0: temp=37.7 th1: temp=34.4 th2: temp=37.0 th3: temp=35.7 sysload=0.59 cputime=18.131 memavail=7432692 print_time=156.591 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 135.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=89903 bytes_read=98023 bytes_retransmit=9 bytes_invalid=0 send_seq=5501 receive_seq=5501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015351 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1468 bytes_read=6558 bytes_retransmit=0 bytes_invalid=0 send_seq=216 receive_seq=216 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000876 adj=49999716 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=8970 bytes_read=26828 bytes_retransmit=9 bytes_invalid=0 send_seq=827 receive_seq=827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997724 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10560 bytes_read=29340 bytes_retransmit=9 bytes_invalid=0 send_seq=959 receive_seq=959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1627 bytes_read=29279 bytes_retransmit=9 bytes_invalid=0 send_seq=222 receive_seq=222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999473 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2221 bytes_read=6460 bytes_retransmit=9 bytes_invalid=0 send_seq=217 receive_seq=217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999889 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.0 EBB42_Gen2_v1.0_T1: temp=26.5 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=21473 bytes_read=107963 bytes_retransmit=0 bytes_invalid=0 send_seq=1864 receive_seq=1864 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999850 adj=31998608 coil_temp=17.8 refs=2 mcu_temp=20.99 supply_voltage=3.012 th0: temp=37.7 th1: temp=35.0 th2: temp=37.0 th3: temp=35.9 sysload=0.59 cputime=18.343 memavail=7432444 print_time=157.591 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 136.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=91489 bytes_read=100068 bytes_retransmit=9 bytes_invalid=0 send_seq=5617 receive_seq=5617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015424 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1474 bytes_read=6587 bytes_retransmit=0 bytes_invalid=0 send_seq=217 receive_seq=217 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000885 adj=49999687 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=8976 bytes_read=26928 bytes_retransmit=9 bytes_invalid=0 send_seq=828 receive_seq=828 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997731 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10566 bytes_read=29440 bytes_retransmit=9 bytes_invalid=0 send_seq=960 receive_seq=960 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999988 adj=63997491 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1633 bytes_read=29512 bytes_retransmit=9 bytes_invalid=0 send_seq=223 receive_seq=223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999472 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2227 bytes_read=6476 bytes_retransmit=9 bytes_invalid=0 send_seq=218 receive_seq=218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999889 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.0 EBB42_Gen2_v1.0_T0: temp=27.2 EBB42_Gen2_v1.0_T1: temp=26.6 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=22377 bytes_read=112475 bytes_retransmit=0 bytes_invalid=0 send_seq=1941 receive_seq=1941 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999849 adj=31998623 coil_temp=17.8 refs=3 mcu_temp=20.98 supply_voltage=3.012 th0: temp=37.5 th1: temp=35.3 th2: temp=38.2 th3: temp=36.0 sysload=0.54 cputime=18.566 memavail=7432444 print_time=158.386 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
probe at 20.000,9.999,1.838 is z=1.964588
Stats 137.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=94254 bytes_read=100673 bytes_retransmit=9 bytes_invalid=0 send_seq=5676 receive_seq=5676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015402 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1480 bytes_read=6603 bytes_retransmit=0 bytes_invalid=0 send_seq=218 receive_seq=218 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000893 adj=49999533 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=8982 bytes_read=27056 bytes_retransmit=9 bytes_invalid=0 send_seq=829 receive_seq=829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997552 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10572 bytes_read=29568 bytes_retransmit=9 bytes_invalid=0 send_seq=961 receive_seq=961 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999986 adj=63997312 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1639 bytes_read=29805 bytes_retransmit=9 bytes_invalid=0 send_seq=224 receive_seq=224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999475 adj=47997499 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2233 bytes_read=6503 bytes_retransmit=9 bytes_invalid=0 send_seq=219 receive_seq=219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999890 adj=11999402 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=26.9 EBB42_Gen2_v1.0_T1: temp=26.6 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=22383 bytes_read=115551 bytes_retransmit=0 bytes_invalid=0 send_seq=1942 receive_seq=1942 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999859 adj=31998533 coil_temp=17.8 refs=3 mcu_temp=20.98 supply_voltage=3.012 th0: temp=36.9 th1: temp=34.9 th2: temp=37.6 th3: temp=35.9 sysload=0.54 cputime=18.791 memavail=7432444 print_time=160.027 buffer_time=0.611 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 138.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=95833 bytes_read=101460 bytes_retransmit=9 bytes_invalid=0 send_seq=5735 receive_seq=5735 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015382 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1486 bytes_read=6619 bytes_retransmit=0 bytes_invalid=0 send_seq=219 receive_seq=219 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000899 adj=49999447 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=8988 bytes_read=27156 bytes_retransmit=9 bytes_invalid=0 send_seq=830 receive_seq=830 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997734 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10578 bytes_read=29668 bytes_retransmit=9 bytes_invalid=0 send_seq=962 receive_seq=962 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999985 adj=63997423 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1645 bytes_read=30053 bytes_retransmit=9 bytes_invalid=0 send_seq=225 receive_seq=225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999474 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2239 bytes_read=6519 bytes_retransmit=9 bytes_invalid=0 send_seq=220 receive_seq=220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999890 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.1 EBB42_Gen2_v1.0_T1: temp=26.5 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=22579 bytes_read=118898 bytes_retransmit=0 bytes_invalid=0 send_seq=1958 receive_seq=1958 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999858 adj=31998727 coil_temp=17.8 refs=2 mcu_temp=20.96 supply_voltage=3.012 th0: temp=37.2 th1: temp=35.4 th2: temp=38.0 th3: temp=36.0 sysload=0.54 cputime=18.965 memavail=7432444 print_time=160.602 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 139.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=98198 bytes_read=104461 bytes_retransmit=9 bytes_invalid=0 send_seq=5904 receive_seq=5904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015356 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1492 bytes_read=6635 bytes_retransmit=0 bytes_invalid=0 send_seq=220 receive_seq=220 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000904 adj=49999510 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=8994 bytes_read=27270 bytes_retransmit=9 bytes_invalid=0 send_seq=831 receive_seq=831 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997755 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10584 bytes_read=29782 bytes_retransmit=9 bytes_invalid=0 send_seq=963 receive_seq=963 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999983 adj=63997460 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1651 bytes_read=30286 bytes_retransmit=9 bytes_invalid=0 send_seq=226 receive_seq=226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999473 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2245 bytes_read=6535 bytes_retransmit=9 bytes_invalid=0 send_seq=221 receive_seq=221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999890 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.0 EBB42_Gen2_v1.0_T0: temp=27.0 EBB42_Gen2_v1.0_T1: temp=26.4 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=24193 bytes_read=124578 bytes_retransmit=0 bytes_invalid=0 send_seq=2093 receive_seq=2093 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999859 adj=31998728 coil_temp=17.8 refs=2 mcu_temp=20.97 supply_voltage=3.012 th0: temp=37.0 th1: temp=35.3 th2: temp=38.1 th3: temp=36.7 sysload=0.54 cputime=19.175 memavail=7432444 print_time=161.602 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
probe at 480.000,230.001,0.668 is z=1.958243
Stats 140.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=100621 bytes_read=105750 bytes_retransmit=9 bytes_invalid=0 send_seq=5996 receive_seq=5996 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=0 freq=400015341 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1498 bytes_read=6651 bytes_retransmit=0 bytes_invalid=0 send_seq=221 receive_seq=221 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000907 adj=49999494 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9000 bytes_read=27398 bytes_retransmit=9 bytes_invalid=0 send_seq=832 receive_seq=832 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997786 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10590 bytes_read=29910 bytes_retransmit=9 bytes_invalid=0 send_seq=964 receive_seq=964 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997512 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1657 bytes_read=30579 bytes_retransmit=9 bytes_invalid=0 send_seq=227 receive_seq=227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999473 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2251 bytes_read=6551 bytes_retransmit=9 bytes_invalid=0 send_seq=222 receive_seq=222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999890 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.1 EBB42_Gen2_v1.0_T1: temp=26.6 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=24593 bytes_read=128292 bytes_retransmit=0 bytes_invalid=0 send_seq=2128 receive_seq=2128 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999861 adj=31998742 coil_temp=17.8 refs=3 mcu_temp=20.96 supply_voltage=3.012 th0: temp=37.5 th1: temp=35.4 th2: temp=38.1 th3: temp=36.4 sysload=0.54 cputime=19.409 memavail=7432444 print_time=163.751 buffer_time=1.329 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 141.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=100958 bytes_read=106175 bytes_retransmit=9 bytes_invalid=0 send_seq=6019 receive_seq=6019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015327 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1504 bytes_read=6680 bytes_retransmit=0 bytes_invalid=0 send_seq=222 receive_seq=222 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000910 adj=49999296 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9006 bytes_read=27498 bytes_retransmit=9 bytes_invalid=0 send_seq=833 receive_seq=833 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997777 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10596 bytes_read=30010 bytes_retransmit=9 bytes_invalid=0 send_seq=965 receive_seq=965 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999981 adj=63997537 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1663 bytes_read=30812 bytes_retransmit=9 bytes_invalid=0 send_seq=228 receive_seq=228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999472 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2257 bytes_read=6567 bytes_retransmit=9 bytes_invalid=0 send_seq=223 receive_seq=223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999890 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.2 EBB42_Gen2_v1.0_T1: temp=26.6 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=24599 bytes_read=131368 bytes_retransmit=0 bytes_invalid=0 send_seq=2129 receive_seq=2129 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999863 adj=31998727 coil_temp=17.8 refs=3 mcu_temp=20.96 supply_voltage=3.012 th0: temp=37.2 th1: temp=35.2 th2: temp=37.9 th3: temp=36.2 sysload=0.50 cputime=19.577 memavail=7432444 print_time=163.751 buffer_time=0.326 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 142.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=102976 bytes_read=107737 bytes_retransmit=9 bytes_invalid=0 send_seq=6118 receive_seq=6118 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015311 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1510 bytes_read=6696 bytes_retransmit=0 bytes_invalid=0 send_seq=223 receive_seq=223 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000912 adj=49999359 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9012 bytes_read=27598 bytes_retransmit=9 bytes_invalid=0 send_seq=834 receive_seq=834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997808 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10602 bytes_read=30110 bytes_retransmit=9 bytes_invalid=0 send_seq=966 receive_seq=966 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999980 adj=63997559 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1669 bytes_read=31045 bytes_retransmit=9 bytes_invalid=0 send_seq=229 receive_seq=229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999471 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2263 bytes_read=6594 bytes_retransmit=9 bytes_invalid=0 send_seq=224 receive_seq=224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999892 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.1 EBB42_Gen2_v1.0_T1: temp=26.4 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=25263 bytes_read=135442 bytes_retransmit=0 bytes_invalid=0 send_seq=2184 receive_seq=2184 retransmit_seq=0 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999868 adj=31998778 coil_temp=17.8 refs=2 mcu_temp=20.94 supply_voltage=3.012 th0: temp=37.3 th1: temp=35.6 th2: temp=38.1 th3: temp=36.6 sysload=0.50 cputime=19.758 memavail=7432444 print_time=164.623 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 143.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=105192 bytes_read=110491 bytes_retransmit=9 bytes_invalid=0 send_seq=6278 receive_seq=6278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015289 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1516 bytes_read=6712 bytes_retransmit=0 bytes_invalid=0 send_seq=224 receive_seq=224 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000912 adj=49999339 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9018 bytes_read=27726 bytes_retransmit=9 bytes_invalid=0 send_seq=835 receive_seq=835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997912 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10608 bytes_read=30238 bytes_retransmit=9 bytes_invalid=0 send_seq=967 receive_seq=967 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999979 adj=63997573 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1675 bytes_read=31353 bytes_retransmit=9 bytes_invalid=0 send_seq=230 receive_seq=230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999470 adj=47997689 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2269 bytes_read=6610 bytes_retransmit=9 bytes_invalid=0 send_seq=225 receive_seq=225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999891 adj=11999472 Octopus_Pro_H723_V1.1: temp=27.9 EBB42_Gen2_v1.0_T0: temp=27.2 EBB42_Gen2_v1.0_T1: temp=26.7 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=26611 bytes_read=140671 bytes_retransmit=0 bytes_invalid=0 send_seq=2298 receive_seq=2298 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999867 adj=31998830 coil_temp=17.8 refs=3 mcu_temp=20.94 supply_voltage=3.012 th0: temp=37.8 th1: temp=35.5 th2: temp=38.3 th3: temp=36.6 sysload=0.50 cputime=19.980 memavail=7432492 print_time=165.533 buffer_time=0.102 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
probe at 20.000,449.999,2.438 is z=1.957806
Calculating bed tilt with: [[19.99999999661664, 9.998593750412038, 1.8734989429731486], [479.9999999966214, 230.00078125003796, 0.7098437341168515], [19.99999999689345, 449.9993750026889, 2.4802807174131]]
Coordinate descent initial error: 1.9111752753453022
Coordinate descent best_err: 1.728986118230398e-10  rounds: 190
Calculated bed tilt parameters: {'x_adjust': -0.0031892636402412675, 'y_adjust': 0.0013790628262934698, 'z_adjust': 1.9234925794881925}
Making the following Z adjustments:
stepper_z = -0.114432
stepper_z1 = -0.222216
stepper_z2 = -1.709063
Retries: 1/10 Probed points range: 1.770437 tolerance: 0.020000
Stats 144.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=108764 bytes_read=111197 bytes_retransmit=9 bytes_invalid=0 send_seq=6354 receive_seq=6354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015278 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1522 bytes_read=6728 bytes_retransmit=0 bytes_invalid=0 send_seq=225 receive_seq=225 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000913 adj=49999282 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9024 bytes_read=27840 bytes_retransmit=9 bytes_invalid=0 send_seq=836 receive_seq=836 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997957 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10614 bytes_read=30352 bytes_retransmit=9 bytes_invalid=0 send_seq=968 receive_seq=968 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999978 adj=63997597 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1681 bytes_read=31586 bytes_retransmit=9 bytes_invalid=0 send_seq=231 receive_seq=231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999470 adj=47997706 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2275 bytes_read=6626 bytes_retransmit=9 bytes_invalid=0 send_seq=226 receive_seq=226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999891 adj=11999470 Octopus_Pro_H723_V1.1: temp=27.9 EBB42_Gen2_v1.0_T0: temp=27.1 EBB42_Gen2_v1.0_T1: temp=26.6 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=26617 bytes_read=143747 bytes_retransmit=0 bytes_invalid=0 send_seq=2299 receive_seq=2299 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999865 adj=31998793 coil_temp=17.8 refs=3 mcu_temp=20.93 supply_voltage=3.012 th0: temp=37.4 th1: temp=35.7 th2: temp=38.5 th3: temp=36.6 sysload=0.50 cputime=20.233 memavail=7432260 print_time=167.288 buffer_time=0.856 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 145.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=110131 bytes_read=111756 bytes_retransmit=9 bytes_invalid=0 send_seq=6398 receive_seq=6398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015265 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1528 bytes_read=6744 bytes_retransmit=0 bytes_invalid=0 send_seq=226 receive_seq=226 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000912 adj=49999205 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9030 bytes_read=27940 bytes_retransmit=9 bytes_invalid=0 send_seq=837 receive_seq=837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997925 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10620 bytes_read=30452 bytes_retransmit=9 bytes_invalid=0 send_seq=969 receive_seq=969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999977 adj=63997586 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1687 bytes_read=31819 bytes_retransmit=9 bytes_invalid=0 send_seq=232 receive_seq=232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999469 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2281 bytes_read=6642 bytes_retransmit=9 bytes_invalid=0 send_seq=227 receive_seq=227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999891 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.0 EBB42_Gen2_v1.0_T0: temp=27.3 EBB42_Gen2_v1.0_T1: temp=26.7 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=26669 bytes_read=146838 bytes_retransmit=0 bytes_invalid=0 send_seq=2303 receive_seq=2303 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999865 adj=31998724 coil_temp=17.8 refs=2 mcu_temp=20.92 supply_voltage=3.012 th0: temp=36.8 th1: temp=35.5 th2: temp=37.6 th3: temp=36.3 sysload=0.50 cputime=20.406 memavail=7432260 print_time=167.615 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 146.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=112564 bytes_read=114437 bytes_retransmit=9 bytes_invalid=0 send_seq=6553 receive_seq=6553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015256 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1534 bytes_read=6773 bytes_retransmit=0 bytes_invalid=0 send_seq=227 receive_seq=227 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000912 adj=49999208 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9036 bytes_read=28068 bytes_retransmit=9 bytes_invalid=0 send_seq=838 receive_seq=838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997926 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10626 bytes_read=30580 bytes_retransmit=9 bytes_invalid=0 send_seq=970 receive_seq=970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999976 adj=63997599 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1693 bytes_read=32112 bytes_retransmit=9 bytes_invalid=0 send_seq=233 receive_seq=233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999469 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2287 bytes_read=6658 bytes_retransmit=9 bytes_invalid=0 send_seq=228 receive_seq=228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999891 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.3 EBB42_Gen2_v1.0_T1: temp=26.6 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=28031 bytes_read=152075 bytes_retransmit=0 bytes_invalid=0 send_seq=2417 receive_seq=2417 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999864 adj=31998730 coil_temp=17.8 refs=2 mcu_temp=20.91 supply_voltage=3.012 th0: temp=37.5 th1: temp=35.9 th2: temp=38.4 th3: temp=36.9 sysload=0.46 cputime=20.615 memavail=7432272 print_time=168.615 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
probe at 20.000,9.999,1.950 is z=1.966207
Stats 147.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=116518 bytes_read=116558 bytes_retransmit=9 bytes_invalid=0 send_seq=6704 receive_seq=6704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=0 freq=400015240 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1540 bytes_read=6789 bytes_retransmit=0 bytes_invalid=0 send_seq=228 receive_seq=228 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000909 adj=49999164 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9042 bytes_read=28168 bytes_retransmit=9 bytes_invalid=0 send_seq=839 receive_seq=839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997871 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10632 bytes_read=30680 bytes_retransmit=9 bytes_invalid=0 send_seq=971 receive_seq=971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999977 adj=63997587 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1699 bytes_read=32345 bytes_retransmit=9 bytes_invalid=0 send_seq=234 receive_seq=234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999469 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2293 bytes_read=6685 bytes_retransmit=9 bytes_invalid=0 send_seq=229 receive_seq=229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999892 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.2 EBB42_Gen2_v1.0_T1: temp=26.7 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=28875 bytes_read=156564 bytes_retransmit=0 bytes_invalid=0 send_seq=2489 receive_seq=2489 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999865 adj=31998699 coil_temp=17.8 refs=3 mcu_temp=20.89 supply_voltage=3.012 th0: temp=37.4 th1: temp=36.0 th2: temp=38.4 th3: temp=36.8 sysload=0.46 cputime=20.872 memavail=7432272 print_time=171.008 buffer_time=1.564 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 148.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=116839 bytes_read=117007 bytes_retransmit=9 bytes_invalid=0 send_seq=6726 receive_seq=6726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015237 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1546 bytes_read=6805 bytes_retransmit=0 bytes_invalid=0 send_seq=229 receive_seq=229 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000911 adj=49999057 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9048 bytes_read=28268 bytes_retransmit=9 bytes_invalid=0 send_seq=840 receive_seq=840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997835 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10638 bytes_read=30780 bytes_retransmit=9 bytes_invalid=0 send_seq=972 receive_seq=972 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999976 adj=63997605 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1705 bytes_read=32608 bytes_retransmit=9 bytes_invalid=0 send_seq=235 receive_seq=235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999470 adj=47997693 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2299 bytes_read=6701 bytes_retransmit=9 bytes_invalid=0 send_seq=230 receive_seq=230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999892 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.2 EBB42_Gen2_v1.0_T1: temp=26.6 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=28881 bytes_read=159640 bytes_retransmit=0 bytes_invalid=0 send_seq=2490 receive_seq=2490 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999864 adj=31998707 coil_temp=17.8 refs=3 mcu_temp=20.87 supply_voltage=3.012 th0: temp=37.1 th1: temp=35.7 th2: temp=38.4 th3: temp=36.7 sysload=0.46 cputime=21.085 memavail=7433640 print_time=171.008 buffer_time=0.563 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 149.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=118509 bytes_read=117933 bytes_retransmit=9 bytes_invalid=0 send_seq=6790 receive_seq=6790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015236 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1552 bytes_read=6821 bytes_retransmit=0 bytes_invalid=0 send_seq=230 receive_seq=230 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000906 adj=49999087 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9054 bytes_read=28410 bytes_retransmit=9 bytes_invalid=0 send_seq=841 receive_seq=841 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997820 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10644 bytes_read=30922 bytes_retransmit=9 bytes_invalid=0 send_seq=973 receive_seq=973 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999975 adj=63997604 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1711 bytes_read=32886 bytes_retransmit=9 bytes_invalid=0 send_seq=236 receive_seq=236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999470 adj=47997708 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2305 bytes_read=6717 bytes_retransmit=9 bytes_invalid=0 send_seq=231 receive_seq=231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999892 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.0 EBB42_Gen2_v1.0_T0: temp=27.1 EBB42_Gen2_v1.0_T1: temp=26.5 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=29161 bytes_read=163106 bytes_retransmit=0 bytes_invalid=0 send_seq=2513 receive_seq=2513 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999862 adj=31998688 coil_temp=17.8 refs=2 mcu_temp=20.86 supply_voltage=3.012 th0: temp=37.3 th1: temp=36.2 th2: temp=38.7 th3: temp=37.0 sysload=0.46 cputime=21.257 memavail=7433640 print_time=171.636 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 150.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=120879 bytes_read=120875 bytes_retransmit=9 bytes_invalid=0 send_seq=6963 receive_seq=6963 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015223 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1558 bytes_read=6837 bytes_retransmit=0 bytes_invalid=0 send_seq=231 receive_seq=231 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000901 adj=49999011 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9060 bytes_read=28510 bytes_retransmit=9 bytes_invalid=0 send_seq=842 receive_seq=842 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997789 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10650 bytes_read=31022 bytes_retransmit=9 bytes_invalid=0 send_seq=974 receive_seq=974 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999975 adj=63997586 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1717 bytes_read=33119 bytes_retransmit=9 bytes_invalid=0 send_seq=237 receive_seq=237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999469 adj=47997703 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2311 bytes_read=6733 bytes_retransmit=9 bytes_invalid=0 send_seq=232 receive_seq=232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999892 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.3 EBB42_Gen2_v1.0_T1: temp=26.7 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=30763 bytes_read=168709 bytes_retransmit=0 bytes_invalid=0 send_seq=2647 receive_seq=2647 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999862 adj=31998665 coil_temp=17.8 refs=2 mcu_temp=20.85 supply_voltage=3.012 th0: temp=37.1 th1: temp=36.6 th2: temp=38.6 th3: temp=37.1 sysload=0.46 cputime=21.471 memavail=7433640 print_time=172.636 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
probe at 480.000,230.001,1.767 is z=1.970031
Stats 151.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=123011 bytes_read=121887 bytes_retransmit=9 bytes_invalid=0 send_seq=7032 receive_seq=7032 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=0 freq=400015218 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1564 bytes_read=6866 bytes_retransmit=0 bytes_invalid=0 send_seq=232 receive_seq=232 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000896 adj=49998956 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9066 bytes_read=28610 bytes_retransmit=9 bytes_invalid=0 send_seq=843 receive_seq=843 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997796 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10656 bytes_read=31122 bytes_retransmit=9 bytes_invalid=0 send_seq=975 receive_seq=975 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999976 adj=63997597 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1723 bytes_read=33367 bytes_retransmit=9 bytes_invalid=0 send_seq=238 receive_seq=238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999469 adj=47997704 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2317 bytes_read=6749 bytes_retransmit=9 bytes_invalid=0 send_seq=233 receive_seq=233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999892 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.0 EBB42_Gen2_v1.0_T1: temp=26.8 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=30983 bytes_read=172138 bytes_retransmit=0 bytes_invalid=0 send_seq=2667 receive_seq=2667 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999861 adj=31998665 coil_temp=17.8 refs=3 mcu_temp=20.85 supply_voltage=3.012 th0: temp=37.5 th1: temp=36.1 th2: temp=38.7 th3: temp=36.9 sysload=0.42 cputime=21.708 memavail=7433640 print_time=174.612 buffer_time=1.166 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 152.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=123836 bytes_read=122352 bytes_retransmit=9 bytes_invalid=0 send_seq=7063 receive_seq=7063 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015218 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1570 bytes_read=6882 bytes_retransmit=0 bytes_invalid=0 send_seq=233 receive_seq=233 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000890 adj=49998915 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9072 bytes_read=28738 bytes_retransmit=9 bytes_invalid=0 send_seq=844 receive_seq=844 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997775 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10662 bytes_read=31250 bytes_retransmit=9 bytes_invalid=0 send_seq=976 receive_seq=976 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999975 adj=63997592 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1729 bytes_read=33645 bytes_retransmit=9 bytes_invalid=0 send_seq=239 receive_seq=239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999469 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2323 bytes_read=6776 bytes_retransmit=9 bytes_invalid=0 send_seq=234 receive_seq=234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999892 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.0 EBB42_Gen2_v1.0_T0: temp=27.1 EBB42_Gen2_v1.0_T1: temp=26.7 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=30989 bytes_read=175214 bytes_retransmit=0 bytes_invalid=0 send_seq=2668 receive_seq=2668 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999860 adj=31998647 coil_temp=17.8 refs=3 mcu_temp=20.85 supply_voltage=3.012 th0: temp=37.6 th1: temp=36.1 th2: temp=38.1 th3: temp=36.8 sysload=0.42 cputime=21.879 memavail=7433640 print_time=174.612 buffer_time=0.166 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 153.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=125651 bytes_read=124244 bytes_retransmit=9 bytes_invalid=0 send_seq=7175 receive_seq=7175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015212 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1576 bytes_read=6898 bytes_retransmit=0 bytes_invalid=0 send_seq=234 receive_seq=234 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000884 adj=49998833 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9078 bytes_read=28838 bytes_retransmit=9 bytes_invalid=0 send_seq=845 receive_seq=845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997758 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10668 bytes_read=31350 bytes_retransmit=9 bytes_invalid=0 send_seq=977 receive_seq=977 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999976 adj=63997583 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1735 bytes_read=33893 bytes_retransmit=9 bytes_invalid=0 send_seq=240 receive_seq=240 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999469 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2329 bytes_read=6792 bytes_retransmit=9 bytes_invalid=0 send_seq=235 receive_seq=235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999892 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.2 EBB42_Gen2_v1.0_T1: temp=26.6 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=31905 bytes_read=179687 bytes_retransmit=0 bytes_invalid=0 send_seq=2744 receive_seq=2744 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999859 adj=31998636 coil_temp=17.7 refs=2 mcu_temp=20.84 supply_voltage=3.012 th0: temp=37.4 th1: temp=35.6 th2: temp=38.7 th3: temp=37.3 sysload=0.42 cputime=22.064 memavail=7433640 print_time=175.637 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 154.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=127571 bytes_read=126684 bytes_retransmit=9 bytes_invalid=0 send_seq=7314 receive_seq=7314 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015200 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1582 bytes_read=6914 bytes_retransmit=0 bytes_invalid=0 send_seq=235 receive_seq=235 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000877 adj=49998784 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9084 bytes_read=28952 bytes_retransmit=9 bytes_invalid=0 send_seq=846 receive_seq=846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997753 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10674 bytes_read=31464 bytes_retransmit=9 bytes_invalid=0 send_seq=978 receive_seq=978 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999975 adj=63997595 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1741 bytes_read=34141 bytes_retransmit=9 bytes_invalid=0 send_seq=241 receive_seq=241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999469 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2335 bytes_read=6808 bytes_retransmit=9 bytes_invalid=0 send_seq=236 receive_seq=236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999892 adj=11999451 Octopus_Pro_H723_V1.1: temp=27.9 EBB42_Gen2_v1.0_T0: temp=27.3 EBB42_Gen2_v1.0_T1: temp=26.6 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=33049 bytes_read=184593 bytes_retransmit=0 bytes_invalid=0 send_seq=2841 receive_seq=2841 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999858 adj=31998634 coil_temp=17.7 refs=3 mcu_temp=20.84 supply_voltage=3.012 th0: temp=38.2 th1: temp=36.6 th2: temp=38.9 th3: temp=37.1 sysload=0.42 cputime=22.288 memavail=7433388 print_time=176.578 buffer_time=0.131 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
probe at 20.000,449.999,2.020 is z=1.963263
Calculating bed tilt with: [[19.99999999661664, 9.998593750412038, 1.9841066912606227], [479.9999999966214, 230.00078125003796, 1.7965324340022222], [19.99999999689345, 449.9993750026889, 2.057050759648458]]
Coordinate descent initial error: 0.04490643685221138
Coordinate descent best_err: 1.178936150293095e-10  rounds: 190
Calculated bed tilt parameters: {'x_adjust': -0.00048703683337005123, 'y_adjust': 0.00016578443011061882, 'z_adjust': 1.9921902830758529}
Making the following Z adjustments:
stepper_z = -0.012369
stepper_z1 = -0.051236
stepper_z2 = -0.255887
Retries: 2/10 Probed points range: 0.260518 tolerance: 0.020000
Stats 155.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=130999 bytes_read=127380 bytes_retransmit=9 bytes_invalid=0 send_seq=7388 receive_seq=7388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015205 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1588 bytes_read=6930 bytes_retransmit=0 bytes_invalid=0 send_seq=236 receive_seq=236 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000871 adj=49998752 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9090 bytes_read=29080 bytes_retransmit=9 bytes_invalid=0 send_seq=847 receive_seq=847 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997759 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10680 bytes_read=31592 bytes_retransmit=9 bytes_invalid=0 send_seq=979 receive_seq=979 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999975 adj=63997605 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1747 bytes_read=34412 bytes_retransmit=9 bytes_invalid=0 send_seq=242 receive_seq=242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999469 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2341 bytes_read=6824 bytes_retransmit=9 bytes_invalid=0 send_seq=237 receive_seq=237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999892 adj=11999452 Octopus_Pro_H723_V1.1: temp=27.8 EBB42_Gen2_v1.0_T0: temp=27.3 EBB42_Gen2_v1.0_T1: temp=26.6 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=33055 bytes_read=187669 bytes_retransmit=0 bytes_invalid=0 send_seq=2842 receive_seq=2842 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999858 adj=31998639 coil_temp=17.7 refs=3 mcu_temp=20.84 supply_voltage=3.011 th0: temp=37.3 th1: temp=36.5 th2: temp=39.2 th3: temp=37.5 sysload=0.42 cputime=22.532 memavail=7433388 print_time=178.266 buffer_time=0.819 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 156.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=132392 bytes_read=127914 bytes_retransmit=9 bytes_invalid=0 send_seq=7430 receive_seq=7430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015253 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1594 bytes_read=6959 bytes_retransmit=0 bytes_invalid=0 send_seq=237 receive_seq=237 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000866 adj=49998750 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9096 bytes_read=29180 bytes_retransmit=9 bytes_invalid=0 send_seq=848 receive_seq=848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997814 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10686 bytes_read=31692 bytes_retransmit=9 bytes_invalid=0 send_seq=980 receive_seq=980 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997558 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1753 bytes_read=34629 bytes_retransmit=9 bytes_invalid=0 send_seq=243 receive_seq=243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999468 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2347 bytes_read=6840 bytes_retransmit=9 bytes_invalid=0 send_seq=238 receive_seq=238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999894 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.0 EBB42_Gen2_v1.0_T0: temp=27.5 EBB42_Gen2_v1.0_T1: temp=26.9 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=33102 bytes_read=190755 bytes_retransmit=0 bytes_invalid=0 send_seq=2845 receive_seq=2845 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999857 adj=31998639 coil_temp=17.7 refs=2 mcu_temp=20.83 supply_voltage=3.012 th0: temp=37.3 th1: temp=36.5 th2: temp=39.0 th3: temp=37.6 sysload=0.39 cputime=22.700 memavail=7433388 print_time=178.627 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 157.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=134905 bytes_read=130725 bytes_retransmit=9 bytes_invalid=0 send_seq=7595 receive_seq=7594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015241 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1600 bytes_read=6975 bytes_retransmit=0 bytes_invalid=0 send_seq=238 receive_seq=238 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000859 adj=49998597 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9102 bytes_read=29280 bytes_retransmit=9 bytes_invalid=0 send_seq=849 receive_seq=849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997804 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10692 bytes_read=31792 bytes_retransmit=9 bytes_invalid=0 send_seq=981 receive_seq=981 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999981 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1759 bytes_read=34861 bytes_retransmit=9 bytes_invalid=0 send_seq=244 receive_seq=244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999469 adj=47997573 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2353 bytes_read=6867 bytes_retransmit=9 bytes_invalid=0 send_seq=239 receive_seq=239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999894 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.4 EBB42_Gen2_v1.0_T1: temp=26.7 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=34524 bytes_read=196101 bytes_retransmit=0 bytes_invalid=0 send_seq=2964 receive_seq=2964 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999857 adj=31998567 coil_temp=17.7 refs=2 mcu_temp=20.81 supply_voltage=3.012 th0: temp=37.5 th1: temp=36.3 th2: temp=39.0 th3: temp=37.3 sysload=0.39 cputime=22.907 memavail=7433388 print_time=179.627 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
probe at 20.000,9.999,1.957 is z=1.959885
Stats 158.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=138549 bytes_read=132456 bytes_retransmit=9 bytes_invalid=0 send_seq=7723 receive_seq=7723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=0 freq=400015230 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1606 bytes_read=6991 bytes_retransmit=0 bytes_invalid=0 send_seq=239 receive_seq=239 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000850 adj=49998615 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9108 bytes_read=29408 bytes_retransmit=9 bytes_invalid=0 send_seq=850 receive_seq=850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997793 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10698 bytes_read=31920 bytes_retransmit=9 bytes_invalid=0 send_seq=982 receive_seq=982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997568 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1765 bytes_read=35136 bytes_retransmit=9 bytes_invalid=0 send_seq=245 receive_seq=245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999472 adj=47997614 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2359 bytes_read=6883 bytes_retransmit=9 bytes_invalid=0 send_seq=240 receive_seq=240 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999895 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.0 EBB42_Gen2_v1.0_T0: temp=27.5 EBB42_Gen2_v1.0_T1: temp=26.5 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=35128 bytes_read=200138 bytes_retransmit=0 bytes_invalid=0 send_seq=3016 receive_seq=3016 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999857 adj=31998587 coil_temp=17.7 refs=3 mcu_temp=20.81 supply_voltage=3.012 th0: temp=37.0 th1: temp=36.9 th2: temp=39.4 th3: temp=37.5 sysload=0.39 cputime=23.158 memavail=7433388 print_time=181.711 buffer_time=1.261 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 159.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=139548 bytes_read=132950 bytes_retransmit=9 bytes_invalid=0 send_seq=7757 receive_seq=7757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=0 freq=400015238 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1612 bytes_read=7007 bytes_retransmit=0 bytes_invalid=0 send_seq=240 receive_seq=240 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000843 adj=49998675 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9114 bytes_read=29522 bytes_retransmit=9 bytes_invalid=0 send_seq=851 receive_seq=851 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997800 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10704 bytes_read=32034 bytes_retransmit=9 bytes_invalid=0 send_seq=983 receive_seq=983 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999981 adj=63997587 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1771 bytes_read=35354 bytes_retransmit=9 bytes_invalid=0 send_seq=246 receive_seq=246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999475 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2365 bytes_read=6899 bytes_retransmit=9 bytes_invalid=0 send_seq=241 receive_seq=241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999894 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.3 EBB42_Gen2_v1.0_T1: temp=26.6 raspberry_pi: temp=21.4  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=35134 bytes_read=203214 bytes_retransmit=0 bytes_invalid=0 send_seq=3017 receive_seq=3017 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999860 adj=31998627 coil_temp=17.7 refs=3 mcu_temp=20.81 supply_voltage=3.012 th0: temp=37.0 th1: temp=36.5 th2: temp=38.6 th3: temp=37.5 sysload=0.39 cputime=23.327 memavail=7433388 print_time=181.711 buffer_time=0.260 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 160.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=141166 bytes_read=134618 bytes_retransmit=9 bytes_invalid=0 send_seq=7857 receive_seq=7857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015239 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1618 bytes_read=7023 bytes_retransmit=0 bytes_invalid=0 send_seq=241 receive_seq=241 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000834 adj=49998552 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9120 bytes_read=29622 bytes_retransmit=9 bytes_invalid=0 send_seq=852 receive_seq=852 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997758 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10710 bytes_read=32134 bytes_retransmit=9 bytes_invalid=0 send_seq=984 receive_seq=984 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997559 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1777 bytes_read=35586 bytes_retransmit=9 bytes_invalid=0 send_seq=247 receive_seq=247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999474 adj=47997730 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2371 bytes_read=6915 bytes_retransmit=9 bytes_invalid=0 send_seq=242 receive_seq=242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999894 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.3 EBB42_Gen2_v1.0_T1: temp=26.8 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=35894 bytes_read=207438 bytes_retransmit=0 bytes_invalid=0 send_seq=3080 receive_seq=3080 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999860 adj=31998672 coil_temp=17.7 refs=2 mcu_temp=20.81 supply_voltage=3.012 th0: temp=37.0 th1: temp=37.0 th2: temp=39.4 th3: temp=37.5 sysload=0.39 cputime=23.507 memavail=7433388 print_time=182.638 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 161.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=143271 bytes_read=137238 bytes_retransmit=9 bytes_invalid=0 send_seq=8015 receive_seq=8015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015229 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1624 bytes_read=7052 bytes_retransmit=0 bytes_invalid=0 send_seq=242 receive_seq=242 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000826 adj=49998505 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9126 bytes_read=29750 bytes_retransmit=9 bytes_invalid=0 send_seq=853 receive_seq=853 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997837 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10716 bytes_read=32262 bytes_retransmit=9 bytes_invalid=0 send_seq=985 receive_seq=985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997567 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1783 bytes_read=35861 bytes_retransmit=9 bytes_invalid=0 send_seq=248 receive_seq=248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999475 adj=47997701 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2377 bytes_read=6931 bytes_retransmit=9 bytes_invalid=0 send_seq=243 receive_seq=243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999894 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.4 EBB42_Gen2_v1.0_T1: temp=26.7 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=37206 bytes_read=212596 bytes_retransmit=0 bytes_invalid=0 send_seq=3191 receive_seq=3191 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999859 adj=31998659 coil_temp=17.7 refs=3 mcu_temp=20.80 supply_voltage=3.012 th0: temp=37.2 th1: temp=37.3 th2: temp=39.6 th3: temp=37.6 sysload=0.36 cputime=23.733 memavail=7433388 print_time=183.679 buffer_time=0.228 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
probe at 480.000,230.001,1.930 is z=1.960287
Stats 162.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=145097 bytes_read=137802 bytes_retransmit=9 bytes_invalid=0 send_seq=8063 receive_seq=8063 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015262 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1630 bytes_read=7068 bytes_retransmit=0 bytes_invalid=0 send_seq=243 receive_seq=243 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000819 adj=49998516 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9132 bytes_read=29850 bytes_retransmit=9 bytes_invalid=0 send_seq=854 receive_seq=854 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997808 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10722 bytes_read=32362 bytes_retransmit=9 bytes_invalid=0 send_seq=986 receive_seq=986 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999981 adj=63997586 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1789 bytes_read=36095 bytes_retransmit=9 bytes_invalid=0 send_seq=249 receive_seq=249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999481 adj=47997711 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2383 bytes_read=6958 bytes_retransmit=9 bytes_invalid=0 send_seq=244 receive_seq=244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999894 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.3 EBB42_Gen2_v1.0_T1: temp=26.8 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=37212 bytes_read=215672 bytes_retransmit=0 bytes_invalid=0 send_seq=3192 receive_seq=3192 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999859 adj=31998653 coil_temp=17.7 refs=3 mcu_temp=20.78 supply_voltage=3.012 th0: temp=37.5 th1: temp=37.0 th2: temp=39.3 th3: temp=37.7 sysload=0.36 cputime=23.943 memavail=7433388 print_time=185.312 buffer_time=0.859 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 163.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=145953 bytes_read=138292 bytes_retransmit=9 bytes_invalid=0 send_seq=8096 receive_seq=8096 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015260 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1636 bytes_read=7084 bytes_retransmit=0 bytes_invalid=0 send_seq=244 receive_seq=244 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000809 adj=49998510 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9138 bytes_read=29950 bytes_retransmit=9 bytes_invalid=0 send_seq=855 receive_seq=855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997697 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10728 bytes_read=32462 bytes_retransmit=9 bytes_invalid=0 send_seq=987 receive_seq=987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999980 adj=63997474 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1795 bytes_read=36359 bytes_retransmit=9 bytes_invalid=0 send_seq=250 receive_seq=250 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999480 adj=47997720 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2389 bytes_read=6974 bytes_retransmit=9 bytes_invalid=0 send_seq=245 receive_seq=245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999894 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.5 EBB42_Gen2_v1.0_T1: temp=26.7 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=37264 bytes_read=218763 bytes_retransmit=0 bytes_invalid=0 send_seq=3196 receive_seq=3196 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999858 adj=31998609 coil_temp=17.7 refs=2 mcu_temp=20.76 supply_voltage=3.012 th0: temp=37.7 th1: temp=36.6 th2: temp=39.0 th3: temp=37.4 sysload=0.36 cputime=24.106 memavail=7433184 print_time=185.639 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 164.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=148385 bytes_read=140993 bytes_retransmit=9 bytes_invalid=0 send_seq=8255 receive_seq=8255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015256 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1642 bytes_read=7100 bytes_retransmit=0 bytes_invalid=0 send_seq=245 receive_seq=245 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000798 adj=49998397 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9144 bytes_read=30092 bytes_retransmit=9 bytes_invalid=0 send_seq=856 receive_seq=856 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997681 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10734 bytes_read=32604 bytes_retransmit=9 bytes_invalid=0 send_seq=988 receive_seq=988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999980 adj=63997473 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1801 bytes_read=36638 bytes_retransmit=9 bytes_invalid=0 send_seq=251 receive_seq=251 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999479 adj=47997704 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2395 bytes_read=6990 bytes_retransmit=9 bytes_invalid=0 send_seq=246 receive_seq=246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999894 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.3 EBB42_Gen2_v1.0_T1: temp=26.7 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=38626 bytes_read=224000 bytes_retransmit=0 bytes_invalid=0 send_seq=3310 receive_seq=3310 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999859 adj=31998606 coil_temp=17.7 refs=2 mcu_temp=20.77 supply_voltage=3.012 th0: temp=37.4 th1: temp=37.1 th2: temp=39.1 th3: temp=37.9 sysload=0.36 cputime=24.319 memavail=7432204 print_time=186.639 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
probe at 20.000,449.999,1.972 is z=1.964759
Calculating bed tilt with: [[19.99999999661664, 9.998593750412038, 1.9972518061241538], [479.9999999966214, 230.00078125003796, 1.9693497883354112], [19.99999999689345, 449.9993750026889, 2.0073781354085938]]
Coordinate descent initial error: 0.0010014249267708802
Coordinate descent best_err: 6.288016994740084e-11  rounds: 175
Calculated bed tilt parameters: {'x_adjust': -7.165375671518342e-05, 'y_adjust': 2.3034017300377504e-05, 'z_adjust': 1.998450741715698}
Making the following Z adjustments:
stepper_z = -0.002183
stepper_z1 = -0.008579
stepper_z2 = -0.038010
Retries: 3/10 Probed points range: 0.038028 tolerance: 0.020000
Stats 165.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=152594 bytes_read=142889 bytes_retransmit=9 bytes_invalid=0 send_seq=8397 receive_seq=8397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=0 freq=400015244 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1648 bytes_read=7116 bytes_retransmit=0 bytes_invalid=0 send_seq=246 receive_seq=246 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000787 adj=49998363 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9150 bytes_read=30192 bytes_retransmit=9 bytes_invalid=0 send_seq=857 receive_seq=857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997692 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10740 bytes_read=32704 bytes_retransmit=9 bytes_invalid=0 send_seq=989 receive_seq=989 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999979 adj=63997486 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1807 bytes_read=36872 bytes_retransmit=9 bytes_invalid=0 send_seq=252 receive_seq=252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999478 adj=47997682 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2401 bytes_read=7006 bytes_retransmit=9 bytes_invalid=0 send_seq=247 receive_seq=247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999894 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.5 EBB42_Gen2_v1.0_T1: temp=26.9 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=39290 bytes_read=228132 bytes_retransmit=0 bytes_invalid=0 send_seq=3367 receive_seq=3367 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999858 adj=31998622 coil_temp=17.7 refs=3 mcu_temp=20.77 supply_voltage=3.012 th0: temp=37.9 th1: temp=37.1 th2: temp=39.3 th3: temp=37.7 sysload=0.36 cputime=24.616 memavail=7426484 print_time=188.938 buffer_time=1.484 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.5 pwm=0.000
Stats 166.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=152948 bytes_read=143329 bytes_retransmit=9 bytes_invalid=0 send_seq=8420 receive_seq=8420 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015267 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1654 bytes_read=7145 bytes_retransmit=0 bytes_invalid=0 send_seq=247 receive_seq=247 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000778 adj=49998522 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9156 bytes_read=30292 bytes_retransmit=9 bytes_invalid=0 send_seq=858 receive_seq=858 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997729 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10746 bytes_read=32804 bytes_retransmit=9 bytes_invalid=0 send_seq=990 receive_seq=990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999979 adj=63997535 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1813 bytes_read=37136 bytes_retransmit=9 bytes_invalid=0 send_seq=253 receive_seq=253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999477 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2407 bytes_read=7022 bytes_retransmit=9 bytes_invalid=0 send_seq=248 receive_seq=248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999894 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.0 EBB42_Gen2_v1.0_T0: temp=27.4 EBB42_Gen2_v1.0_T1: temp=26.7 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=39296 bytes_read=231208 bytes_retransmit=0 bytes_invalid=0 send_seq=3368 receive_seq=3368 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999858 adj=31998637 coil_temp=17.7 refs=3 mcu_temp=20.76 supply_voltage=3.012 th0: temp=37.3 th1: temp=36.8 th2: temp=39.4 th3: temp=37.6 sysload=0.33 cputime=24.796 memavail=7432128 print_time=188.938 buffer_time=0.484 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 167.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=155124 bytes_read=144474 bytes_retransmit=9 bytes_invalid=0 send_seq=8503 receive_seq=8503 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015263 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1660 bytes_read=7161 bytes_retransmit=0 bytes_invalid=0 send_seq=248 receive_seq=248 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000760 adj=49998337 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9162 bytes_read=30420 bytes_retransmit=9 bytes_invalid=0 send_seq=859 receive_seq=859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997658 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10752 bytes_read=32932 bytes_retransmit=9 bytes_invalid=0 send_seq=991 receive_seq=991 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999984 adj=63997479 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1819 bytes_read=37400 bytes_retransmit=9 bytes_invalid=0 send_seq=254 receive_seq=254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999477 adj=47997613 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2413 bytes_read=7049 bytes_retransmit=9 bytes_invalid=0 send_seq=249 receive_seq=249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999894 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.0 EBB42_Gen2_v1.0_T0: temp=27.5 EBB42_Gen2_v1.0_T1: temp=26.8 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=39696 bytes_read=234878 bytes_retransmit=0 bytes_invalid=0 send_seq=3401 receive_seq=3401 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999858 adj=31998603 coil_temp=17.7 refs=2 mcu_temp=20.75 supply_voltage=3.012 th0: temp=38.0 th1: temp=37.0 th2: temp=39.4 th3: temp=38.0 sysload=0.33 cputime=24.975 memavail=7432128 print_time=189.661 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 168.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=157604 bytes_read=147570 bytes_retransmit=9 bytes_invalid=0 send_seq=8680 receive_seq=8680 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015318 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1672 bytes_read=7193 bytes_retransmit=0 bytes_invalid=0 send_seq=250 receive_seq=250 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000698 adj=49998162 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9174 bytes_read=30536 bytes_retransmit=9 bytes_invalid=0 send_seq=861 receive_seq=861 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997753 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10764 bytes_read=33048 bytes_retransmit=9 bytes_invalid=0 send_seq=993 receive_seq=993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999985 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1831 bytes_read=37665 bytes_retransmit=9 bytes_invalid=0 send_seq=256 receive_seq=256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999476 adj=47997617 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2425 bytes_read=7081 bytes_retransmit=9 bytes_invalid=0 send_seq=251 receive_seq=251 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999894 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.0 EBB42_Gen2_v1.0_T0: temp=27.5 EBB42_Gen2_v1.0_T1: temp=26.7 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=41316 bytes_read=240502 bytes_retransmit=0 bytes_invalid=0 send_seq=3537 receive_seq=3537 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999857 adj=31998621 coil_temp=17.7 refs=2 mcu_temp=20.75 supply_voltage=3.012 th0: temp=37.4 th1: temp=37.3 th2: temp=39.8 th3: temp=38.0 sysload=0.33 cputime=25.190 memavail=7432128 print_time=190.661 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
probe at 20.000,9.999,1.971 is z=1.970962
Stats 169.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=160504 bytes_read=148416 bytes_retransmit=9 bytes_invalid=0 send_seq=8755 receive_seq=8755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015306 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1678 bytes_read=7209 bytes_retransmit=0 bytes_invalid=0 send_seq=251 receive_seq=251 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000657 adj=49997304 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9180 bytes_read=30650 bytes_retransmit=9 bytes_invalid=0 send_seq=862 receive_seq=862 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997578 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10770 bytes_read=33162 bytes_retransmit=9 bytes_invalid=0 send_seq=994 receive_seq=994 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999984 adj=63997449 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1837 bytes_read=37929 bytes_retransmit=9 bytes_invalid=0 send_seq=257 receive_seq=257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999475 adj=47997509 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2431 bytes_read=7097 bytes_retransmit=9 bytes_invalid=0 send_seq=252 receive_seq=252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999893 adj=11999405 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.5 EBB42_Gen2_v1.0_T1: temp=26.9 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=41380 bytes_read=243684 bytes_retransmit=0 bytes_invalid=0 send_seq=3544 receive_seq=3544 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999857 adj=31998559 coil_temp=17.7 refs=3 mcu_temp=20.75 supply_voltage=3.012 th0: temp=37.4 th1: temp=37.7 th2: temp=39.6 th3: temp=38.0 sysload=0.33 cputime=25.439 memavail=7432128 print_time=192.533 buffer_time=1.077 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 170.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=161507 bytes_read=148907 bytes_retransmit=9 bytes_invalid=0 send_seq=8788 receive_seq=8788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015361 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1684 bytes_read=7225 bytes_retransmit=0 bytes_invalid=0 send_seq=252 receive_seq=252 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000609 adj=49997395 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9186 bytes_read=30778 bytes_retransmit=9 bytes_invalid=0 send_seq=863 receive_seq=863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997666 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10776 bytes_read=33290 bytes_retransmit=9 bytes_invalid=0 send_seq=995 receive_seq=995 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999983 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1843 bytes_read=38193 bytes_retransmit=9 bytes_invalid=0 send_seq=258 receive_seq=258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999477 adj=47997581 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2437 bytes_read=7113 bytes_retransmit=9 bytes_invalid=0 send_seq=253 receive_seq=253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999893 adj=11999423 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=27.3 EBB42_Gen2_v1.0_T1: temp=26.8 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=41386 bytes_read=246760 bytes_retransmit=0 bytes_invalid=0 send_seq=3545 receive_seq=3545 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999857 adj=31998605 coil_temp=17.7 refs=3 mcu_temp=20.76 supply_voltage=3.011 th0: temp=37.7 th1: temp=37.5 th2: temp=39.5 th3: temp=37.8 sysload=0.33 cputime=25.614 memavail=7432128 print_time=192.533 buffer_time=0.076 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 171.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=163483 bytes_read=151021 bytes_retransmit=9 bytes_invalid=0 send_seq=8916 receive_seq=8916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015342 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1690 bytes_read=7254 bytes_retransmit=0 bytes_invalid=0 send_seq=253 receive_seq=253 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000556 adj=49996614 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9192 bytes_read=30878 bytes_retransmit=9 bytes_invalid=0 send_seq=864 receive_seq=864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997523 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10782 bytes_read=33390 bytes_retransmit=9 bytes_invalid=0 send_seq=996 receive_seq=996 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999983 adj=63997362 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1849 bytes_read=38427 bytes_retransmit=9 bytes_invalid=0 send_seq=259 receive_seq=259 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999476 adj=47997517 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2443 bytes_read=7129 bytes_retransmit=9 bytes_invalid=0 send_seq=254 receive_seq=254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999893 adj=11999397 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.4 EBB42_Gen2_v1.0_T1: temp=26.8 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=42446 bytes_read=251461 bytes_retransmit=0 bytes_invalid=0 send_seq=3633 receive_seq=3633 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999856 adj=31998536 coil_temp=17.7 refs=2 mcu_temp=20.75 supply_voltage=3.011 th0: temp=37.7 th1: temp=37.8 th2: temp=39.7 th3: temp=38.1 sysload=0.30 cputime=25.806 memavail=7432128 print_time=193.661 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 172.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=165184 bytes_read=153181 bytes_retransmit=9 bytes_invalid=0 send_seq=9044 receive_seq=9044 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015328 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1696 bytes_read=7270 bytes_retransmit=0 bytes_invalid=0 send_seq=254 receive_seq=254 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000499 adj=49996371 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9198 bytes_read=30978 bytes_retransmit=9 bytes_invalid=0 send_seq=865 receive_seq=865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997714 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10788 bytes_read=33490 bytes_retransmit=9 bytes_invalid=0 send_seq=997 receive_seq=997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997439 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1855 bytes_read=38691 bytes_retransmit=9 bytes_invalid=0 send_seq=260 receive_seq=260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999476 adj=47997569 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2449 bytes_read=7156 bytes_retransmit=9 bytes_invalid=0 send_seq=255 receive_seq=255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999893 adj=11999414 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.5 EBB42_Gen2_v1.0_T1: temp=26.8 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=43458 bytes_read=256158 bytes_retransmit=0 bytes_invalid=0 send_seq=3719 receive_seq=3719 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999857 adj=31998569 coil_temp=17.7 refs=3 mcu_temp=20.74 supply_voltage=3.011 th0: temp=37.7 th1: temp=37.1 th2: temp=39.7 th3: temp=38.2 sysload=0.30 cputime=26.029 memavail=7432128 print_time=194.501 buffer_time=0.044 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
probe at 480.000,230.001,1.958 is z=1.962303
Stats 173.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=167000 bytes_read=153721 bytes_retransmit=9 bytes_invalid=0 send_seq=9090 receive_seq=9090 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015347 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1702 bytes_read=7286 bytes_retransmit=0 bytes_invalid=0 send_seq=255 receive_seq=255 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000438 adj=49996043 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9204 bytes_read=31106 bytes_retransmit=9 bytes_invalid=0 send_seq=866 receive_seq=866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997734 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10794 bytes_read=33618 bytes_retransmit=9 bytes_invalid=0 send_seq=998 receive_seq=998 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999981 adj=63997485 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1861 bytes_read=38970 bytes_retransmit=9 bytes_invalid=0 send_seq=261 receive_seq=261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999475 adj=47997602 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2455 bytes_read=7172 bytes_retransmit=9 bytes_invalid=0 send_seq=256 receive_seq=256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999893 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.4 EBB42_Gen2_v1.0_T1: temp=26.9 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=43464 bytes_read=259234 bytes_retransmit=0 bytes_invalid=0 send_seq=3720 receive_seq=3720 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999858 adj=31998615 coil_temp=17.7 refs=3 mcu_temp=20.74 supply_voltage=3.012 th0: temp=37.8 th1: temp=36.9 th2: temp=39.6 th3: temp=37.9 sysload=0.30 cputime=26.235 memavail=7432128 print_time=196.138 buffer_time=0.679 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 174.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=168249 bytes_read=154346 bytes_retransmit=9 bytes_invalid=0 send_seq=9136 receive_seq=9136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015393 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1708 bytes_read=7302 bytes_retransmit=0 bytes_invalid=0 send_seq=256 receive_seq=256 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000375 adj=49996098 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9210 bytes_read=31206 bytes_retransmit=9 bytes_invalid=0 send_seq=867 receive_seq=867 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997787 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10800 bytes_read=33718 bytes_retransmit=9 bytes_invalid=0 send_seq=999 receive_seq=999 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999981 adj=63997443 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1867 bytes_read=39204 bytes_retransmit=9 bytes_invalid=0 send_seq=262 receive_seq=262 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999476 adj=47997570 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2461 bytes_read=7188 bytes_retransmit=9 bytes_invalid=0 send_seq=257 receive_seq=257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999894 adj=11999418 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.5 EBB42_Gen2_v1.0_T1: temp=26.8 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=43552 bytes_read=262410 bytes_retransmit=0 bytes_invalid=0 send_seq=3727 receive_seq=3727 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999858 adj=31998616 coil_temp=17.7 refs=2 mcu_temp=20.73 supply_voltage=3.012 th0: temp=38.0 th1: temp=37.5 th2: temp=39.8 th3: temp=37.9 sysload=0.30 cputime=26.401 memavail=7431656 print_time=196.663 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 175.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=170718 bytes_read=157423 bytes_retransmit=9 bytes_invalid=0 send_seq=9311 receive_seq=9311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015411 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1714 bytes_read=7318 bytes_retransmit=0 bytes_invalid=0 send_seq=257 receive_seq=257 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000305 adj=49995376 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9216 bytes_read=31320 bytes_retransmit=9 bytes_invalid=0 send_seq=868 receive_seq=868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997656 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10806 bytes_read=33832 bytes_retransmit=9 bytes_invalid=0 send_seq=1000 receive_seq=1000 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999980 adj=63997343 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1873 bytes_read=39468 bytes_retransmit=9 bytes_invalid=0 send_seq=263 receive_seq=263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999476 adj=47997512 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2467 bytes_read=7204 bytes_retransmit=9 bytes_invalid=0 send_seq=258 receive_seq=258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999893 adj=11999404 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.4 EBB42_Gen2_v1.0_T1: temp=26.8 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45166 bytes_read=268018 bytes_retransmit=0 bytes_invalid=0 send_seq=3862 receive_seq=3862 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999858 adj=31998555 coil_temp=17.7 refs=2 mcu_temp=20.73 supply_voltage=3.012 th0: temp=38.1 th1: temp=37.4 th2: temp=39.9 th3: temp=38.0 sysload=0.30 cputime=26.615 memavail=7431656 print_time=197.663 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
probe at 20.000,449.999,1.959 is z=1.958513
Calculating bed tilt with: [[19.99999999661664, 9.998593750412038, 1.9995470953807621], [479.9999999966214, 230.00078125003796, 1.9957070566732922], [19.99999999689345, 449.9993750026889, 2.0007467505460683]]
Coordinate descent initial error: 1.919212137850554e-05
Coordinate descent best_err: 1.4571365102728212e-10  rounds: 180
Calculated bed tilt parameters: {'x_adjust': -9.673278445856035e-06, 'y_adjust': 2.7472305357870817e-06, 'z_adjust': 1.9997154377003645}
Making the following Z adjustments:
stepper_z = -0.000360
stepper_z1 = -0.001405
stepper_z2 = -0.005197
Retries: 4/10 Probed points range: 0.005040 tolerance: 0.020000
Stats 176.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=172435 bytes_read=158638 bytes_retransmit=9 bytes_invalid=0 send_seq=9390 receive_seq=9390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015420 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1720 bytes_read=7347 bytes_retransmit=0 bytes_invalid=0 send_seq=258 receive_seq=258 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000234 adj=49995067 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9222 bytes_read=31448 bytes_retransmit=9 bytes_invalid=0 send_seq=869 receive_seq=869 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997605 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10812 bytes_read=33960 bytes_retransmit=9 bytes_invalid=0 send_seq=1001 receive_seq=1001 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999980 adj=63997333 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1879 bytes_read=39732 bytes_retransmit=9 bytes_invalid=0 send_seq=264 receive_seq=264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999475 adj=47997500 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2473 bytes_read=7220 bytes_retransmit=9 bytes_invalid=0 send_seq=259 receive_seq=259 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999893 adj=11999402 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.6 EBB42_Gen2_v1.0_T1: temp=26.9 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45549 bytes_read=270864 bytes_retransmit=0 bytes_invalid=0 send_seq=3896 receive_seq=3896 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999857 adj=31998556 coil_temp=17.7 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=38.6 th1: temp=37.5 th2: temp=39.6 th3: temp=38.3 sysload=0.28 cputime=26.796 memavail=7431656 print_time=198.915 buffer_time=0.454 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 177.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=172733 bytes_read=159092 bytes_retransmit=9 bytes_invalid=0 send_seq=9413 receive_seq=9413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015411 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1726 bytes_read=7363 bytes_retransmit=0 bytes_invalid=0 send_seq=259 receive_seq=259 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000161 adj=49995019 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9228 bytes_read=31548 bytes_retransmit=9 bytes_invalid=0 send_seq=870 receive_seq=870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997642 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10818 bytes_read=34060 bytes_retransmit=9 bytes_invalid=0 send_seq=1002 receive_seq=1002 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999979 adj=63997359 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1885 bytes_read=39966 bytes_retransmit=9 bytes_invalid=0 send_seq=265 receive_seq=265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999475 adj=47997516 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2479 bytes_read=7247 bytes_retransmit=9 bytes_invalid=0 send_seq=260 receive_seq=260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999893 adj=11999407 Octopus_Pro_H723_V1.1: temp=27.9 EBB42_Gen2_v1.0_T0: temp=27.4 EBB42_Gen2_v1.0_T1: temp=26.8 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45555 bytes_read=271220 bytes_retransmit=0 bytes_invalid=0 send_seq=3897 receive_seq=3897 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999857 adj=31998558 coil_temp=17.7 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=38.1 th1: temp=37.8 th2: temp=39.9 th3: temp=38.3 sysload=0.28 cputime=26.839 memavail=7431656 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 178.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=173031 bytes_read=159517 bytes_retransmit=9 bytes_invalid=0 send_seq=9436 receive_seq=9436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015400 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1732 bytes_read=7379 bytes_retransmit=0 bytes_invalid=0 send_seq=260 receive_seq=260 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000086 adj=49994377 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9234 bytes_read=31643 bytes_retransmit=9 bytes_invalid=0 send_seq=871 receive_seq=871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997660 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10824 bytes_read=34155 bytes_retransmit=9 bytes_invalid=0 send_seq=1003 receive_seq=1003 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999979 adj=63997393 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1891 bytes_read=40245 bytes_retransmit=9 bytes_invalid=0 send_seq=266 receive_seq=266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999476 adj=47997550 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2485 bytes_read=7263 bytes_retransmit=9 bytes_invalid=0 send_seq=261 receive_seq=261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999893 adj=11999414 Octopus_Pro_H723_V1.1: temp=28.0 EBB42_Gen2_v1.0_T0: temp=27.4 EBB42_Gen2_v1.0_T1: temp=26.9 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45561 bytes_read=271576 bytes_retransmit=0 bytes_invalid=0 send_seq=3898 receive_seq=3898 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999857 adj=31998572 coil_temp=17.7 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=37.9 th1: temp=37.6 th2: temp=39.9 th3: temp=38.8 sysload=0.28 cputime=26.882 memavail=7431656 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 179.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=173329 bytes_read=159942 bytes_retransmit=9 bytes_invalid=0 send_seq=9459 receive_seq=9459 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015391 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1738 bytes_read=7395 bytes_retransmit=0 bytes_invalid=0 send_seq=261 receive_seq=261 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000010 adj=49994230 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9240 bytes_read=31762 bytes_retransmit=9 bytes_invalid=0 send_seq=872 receive_seq=872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997825 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10830 bytes_read=34274 bytes_retransmit=9 bytes_invalid=0 send_seq=1004 receive_seq=1004 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999979 adj=63997447 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1897 bytes_read=40509 bytes_retransmit=9 bytes_invalid=0 send_seq=267 receive_seq=267 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999479 adj=47997592 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2491 bytes_read=7279 bytes_retransmit=9 bytes_invalid=0 send_seq=262 receive_seq=262 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999893 adj=11999423 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.7 EBB42_Gen2_v1.0_T1: temp=26.8 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45567 bytes_read=271932 bytes_retransmit=0 bytes_invalid=0 send_seq=3899 receive_seq=3899 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999857 adj=31998593 coil_temp=17.7 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=37.8 th1: temp=37.8 th2: temp=40.4 th3: temp=38.5 sysload=0.28 cputime=26.923 memavail=7431656 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 180.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=173627 bytes_read=160411 bytes_retransmit=9 bytes_invalid=0 send_seq=9482 receive_seq=9482 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015379 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1744 bytes_read=7410 bytes_retransmit=0 bytes_invalid=0 send_seq=262 receive_seq=262 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999932 adj=49994072 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=9246 bytes_read=31869 bytes_retransmit=9 bytes_invalid=0 send_seq=873 receive_seq=873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997798 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=10836 bytes_read=34381 bytes_retransmit=9 bytes_invalid=0 send_seq=1005 receive_seq=1005 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999979 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1903 bytes_read=40743 bytes_retransmit=9 bytes_invalid=0 send_seq=268 receive_seq=268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999479 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2497 bytes_read=7295 bytes_retransmit=9 bytes_invalid=0 send_seq=263 receive_seq=263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999893 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.5 EBB42_Gen2_v1.0_T1: temp=27.0 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45573 bytes_read=272288 bytes_retransmit=0 bytes_invalid=0 send_seq=3900 receive_seq=3900 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999857 adj=31998615 coil_temp=17.7 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=37.8 th1: temp=37.8 th2: temp=40.4 th3: temp=38.4 sysload=0.28 cputime=26.965 memavail=7431696 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 181.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=173925 bytes_read=160836 bytes_retransmit=9 bytes_invalid=0 send_seq=9505 receive_seq=9505 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015367 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1750 bytes_read=7438 bytes_retransmit=0 bytes_invalid=0 send_seq=263 receive_seq=263 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999854 adj=49993924 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=9252 bytes_read=31962 bytes_retransmit=9 bytes_invalid=0 send_seq=874 receive_seq=874 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997779 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=10842 bytes_read=34474 bytes_retransmit=9 bytes_invalid=0 send_seq=1006 receive_seq=1006 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999979 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1909 bytes_read=41007 bytes_retransmit=9 bytes_invalid=0 send_seq=269 receive_seq=269 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999478 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2503 bytes_read=7311 bytes_retransmit=9 bytes_invalid=0 send_seq=264 receive_seq=264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999893 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.5 EBB42_Gen2_v1.0_T1: temp=27.1 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45579 bytes_read=272644 bytes_retransmit=0 bytes_invalid=0 send_seq=3901 receive_seq=3901 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999858 adj=31998631 coil_temp=17.7 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=37.7 th1: temp=37.8 th2: temp=40.3 th3: temp=38.6 sysload=0.33 cputime=27.008 memavail=7431696 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 182.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=174223 bytes_read=161256 bytes_retransmit=9 bytes_invalid=0 send_seq=9528 receive_seq=9528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015360 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1756 bytes_read=7453 bytes_retransmit=0 bytes_invalid=0 send_seq=264 receive_seq=264 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999777 adj=49993783 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=9258 bytes_read=32087 bytes_retransmit=9 bytes_invalid=0 send_seq=875 receive_seq=875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997774 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=10848 bytes_read=34599 bytes_retransmit=9 bytes_invalid=0 send_seq=1007 receive_seq=1007 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999979 adj=63997552 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1915 bytes_read=41271 bytes_retransmit=9 bytes_invalid=0 send_seq=270 receive_seq=270 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999480 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2509 bytes_read=7338 bytes_retransmit=9 bytes_invalid=0 send_seq=265 receive_seq=265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999894 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.5 EBB42_Gen2_v1.0_T1: temp=26.8 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45585 bytes_read=273000 bytes_retransmit=0 bytes_invalid=0 send_seq=3902 receive_seq=3902 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999858 adj=31998664 coil_temp=17.7 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=37.2 th1: temp=38.0 th2: temp=40.6 th3: temp=39.0 sysload=0.33 cputime=27.057 memavail=7426548 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 183.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=174521 bytes_read=161710 bytes_retransmit=9 bytes_invalid=0 send_seq=9551 receive_seq=9551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015348 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1762 bytes_read=7468 bytes_retransmit=0 bytes_invalid=0 send_seq=265 receive_seq=265 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999699 adj=49993673 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=9264 bytes_read=32187 bytes_retransmit=9 bytes_invalid=0 send_seq=876 receive_seq=876 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997751 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=10854 bytes_read=34699 bytes_retransmit=9 bytes_invalid=0 send_seq=1008 receive_seq=1008 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999978 adj=63997556 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1921 bytes_read=41520 bytes_retransmit=9 bytes_invalid=0 send_seq=271 receive_seq=271 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999480 adj=47997716 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2515 bytes_read=7354 bytes_retransmit=9 bytes_invalid=0 send_seq=266 receive_seq=266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999894 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.7 EBB42_Gen2_v1.0_T1: temp=27.1 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45591 bytes_read=273356 bytes_retransmit=0 bytes_invalid=0 send_seq=3903 receive_seq=3903 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999858 adj=31998661 coil_temp=17.7 refs=0 mcu_temp=20.73 supply_voltage=3.012 th0: temp=37.9 th1: temp=38.1 th2: temp=40.6 th3: temp=38.7 sysload=0.33 cputime=27.102 memavail=7432700 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 184.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000003 mcu_task_stddev=0.000004 bytes_write=174819 bytes_read=162135 bytes_retransmit=9 bytes_invalid=0 send_seq=9574 receive_seq=9574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015341 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1768 bytes_read=7483 bytes_retransmit=0 bytes_invalid=0 send_seq=266 receive_seq=266 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999621 adj=49993552 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=9270 bytes_read=32287 bytes_retransmit=9 bytes_invalid=0 send_seq=877 receive_seq=877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997872 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=10860 bytes_read=34799 bytes_retransmit=9 bytes_invalid=0 send_seq=1009 receive_seq=1009 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999978 adj=63997567 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1927 bytes_read=41784 bytes_retransmit=9 bytes_invalid=0 send_seq=272 receive_seq=272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999479 adj=47997703 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2521 bytes_read=7370 bytes_retransmit=9 bytes_invalid=0 send_seq=267 receive_seq=267 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999894 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.6 EBB42_Gen2_v1.0_T1: temp=27.0 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45597 bytes_read=273712 bytes_retransmit=0 bytes_invalid=0 send_seq=3904 receive_seq=3904 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999862 adj=31998672 coil_temp=17.7 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=37.8 th1: temp=38.3 th2: temp=40.7 th3: temp=38.8 sysload=0.33 cputime=27.146 memavail=7432236 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 185.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=175117 bytes_read=162575 bytes_retransmit=9 bytes_invalid=0 send_seq=9597 receive_seq=9597 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015332 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1774 bytes_read=7498 bytes_retransmit=0 bytes_invalid=0 send_seq=267 receive_seq=267 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999542 adj=49993444 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=9276 bytes_read=32429 bytes_retransmit=9 bytes_invalid=0 send_seq=878 receive_seq=878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997822 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=10866 bytes_read=34941 bytes_retransmit=9 bytes_invalid=0 send_seq=1010 receive_seq=1010 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999978 adj=63997567 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1933 bytes_read=42048 bytes_retransmit=9 bytes_invalid=0 send_seq=273 receive_seq=273 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999478 adj=47997689 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2527 bytes_read=7386 bytes_retransmit=9 bytes_invalid=0 send_seq=268 receive_seq=268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999894 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.6 EBB42_Gen2_v1.0_T1: temp=26.9 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45603 bytes_read=274068 bytes_retransmit=0 bytes_invalid=0 send_seq=3905 receive_seq=3905 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999863 adj=31998731 coil_temp=17.7 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=37.7 th1: temp=38.1 th2: temp=40.7 th3: temp=39.0 sysload=0.33 cputime=27.190 memavail=7432240 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 186.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=175415 bytes_read=163029 bytes_retransmit=9 bytes_invalid=0 send_seq=9620 receive_seq=9620 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015322 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1780 bytes_read=7527 bytes_retransmit=0 bytes_invalid=0 send_seq=268 receive_seq=268 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999465 adj=49993334 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=9282 bytes_read=32529 bytes_retransmit=9 bytes_invalid=0 send_seq=879 receive_seq=879 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997811 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=10872 bytes_read=35041 bytes_retransmit=9 bytes_invalid=0 send_seq=1011 receive_seq=1011 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999978 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1939 bytes_read=42282 bytes_retransmit=9 bytes_invalid=0 send_seq=274 receive_seq=274 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999478 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2533 bytes_read=7402 bytes_retransmit=9 bytes_invalid=0 send_seq=269 receive_seq=269 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999894 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=27.6 EBB42_Gen2_v1.0_T1: temp=26.8 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45609 bytes_read=274424 bytes_retransmit=0 bytes_invalid=0 send_seq=3906 receive_seq=3906 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999862 adj=31998731 coil_temp=17.7 refs=0 mcu_temp=20.74 supply_voltage=3.011 th0: temp=37.4 th1: temp=38.1 th2: temp=40.7 th3: temp=38.9 sysload=0.31 cputime=27.234 memavail=7432240 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 187.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=175708 bytes_read=163449 bytes_retransmit=9 bytes_invalid=0 send_seq=9642 receive_seq=9642 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015314 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1786 bytes_read=7543 bytes_retransmit=0 bytes_invalid=0 send_seq=269 receive_seq=269 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999388 adj=49993242 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=9288 bytes_read=32629 bytes_retransmit=9 bytes_invalid=0 send_seq=880 receive_seq=880 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997789 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=10878 bytes_read=35141 bytes_retransmit=9 bytes_invalid=0 send_seq=1012 receive_seq=1012 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999977 adj=63997586 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1945 bytes_read=42561 bytes_retransmit=9 bytes_invalid=0 send_seq=275 receive_seq=275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999477 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2539 bytes_read=7429 bytes_retransmit=9 bytes_invalid=0 send_seq=270 receive_seq=270 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999894 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.7 EBB42_Gen2_v1.0_T1: temp=26.9 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45615 bytes_read=274780 bytes_retransmit=0 bytes_invalid=0 send_seq=3907 receive_seq=3907 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999861 adj=31998708 coil_temp=17.7 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=37.6 th1: temp=38.3 th2: temp=40.7 th3: temp=39.2 sysload=0.31 cputime=27.280 memavail=7431992 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 188.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=176006 bytes_read=163874 bytes_retransmit=9 bytes_invalid=0 send_seq=9665 receive_seq=9665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015315 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1792 bytes_read=7559 bytes_retransmit=0 bytes_invalid=0 send_seq=270 receive_seq=270 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999313 adj=49993163 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=9294 bytes_read=32757 bytes_retransmit=9 bytes_invalid=0 send_seq=881 receive_seq=881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997825 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=10884 bytes_read=35269 bytes_retransmit=9 bytes_invalid=0 send_seq=1013 receive_seq=1013 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999977 adj=63997605 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1951 bytes_read=42825 bytes_retransmit=9 bytes_invalid=0 send_seq=276 receive_seq=276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999477 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2545 bytes_read=7445 bytes_retransmit=9 bytes_invalid=0 send_seq=271 receive_seq=271 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999895 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.7 EBB42_Gen2_v1.0_T1: temp=27.0 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45621 bytes_read=275136 bytes_retransmit=0 bytes_invalid=0 send_seq=3908 receive_seq=3908 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999861 adj=31998687 coil_temp=17.7 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=37.4 th1: temp=38.3 th2: temp=41.0 th3: temp=39.1 sysload=0.31 cputime=27.324 memavail=7431992 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 189.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=176299 bytes_read=164323 bytes_retransmit=9 bytes_invalid=0 send_seq=9687 receive_seq=9687 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015315 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1798 bytes_read=7575 bytes_retransmit=0 bytes_invalid=0 send_seq=271 receive_seq=271 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49993094 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=9300 bytes_read=32857 bytes_retransmit=9 bytes_invalid=0 send_seq=882 receive_seq=882 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997772 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=10890 bytes_read=35369 bytes_retransmit=9 bytes_invalid=0 send_seq=1014 receive_seq=1014 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999977 adj=63997580 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1957 bytes_read=43059 bytes_retransmit=9 bytes_invalid=0 send_seq=277 receive_seq=277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999479 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2551 bytes_read=7461 bytes_retransmit=9 bytes_invalid=0 send_seq=272 receive_seq=272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999895 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.5 EBB42_Gen2_v1.0_T1: temp=27.2 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45627 bytes_read=275492 bytes_retransmit=0 bytes_invalid=0 send_seq=3909 receive_seq=3909 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999861 adj=31998668 coil_temp=17.7 refs=0 mcu_temp=20.75 supply_voltage=3.012 th0: temp=37.5 th1: temp=38.3 th2: temp=41.1 th3: temp=39.2 sysload=0.31 cputime=27.367 memavail=7431992 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 190.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=176592 bytes_read=164758 bytes_retransmit=9 bytes_invalid=0 send_seq=9709 receive_seq=9709 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015312 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1804 bytes_read=7591 bytes_retransmit=0 bytes_invalid=0 send_seq=272 receive_seq=272 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999165 adj=49993030 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9306 bytes_read=32971 bytes_retransmit=9 bytes_invalid=0 send_seq=883 receive_seq=883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997862 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10896 bytes_read=35483 bytes_retransmit=9 bytes_invalid=0 send_seq=1015 receive_seq=1015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999977 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1963 bytes_read=43338 bytes_retransmit=9 bytes_invalid=0 send_seq=278 receive_seq=278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999478 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2557 bytes_read=7477 bytes_retransmit=9 bytes_invalid=0 send_seq=273 receive_seq=273 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999895 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=27.7 EBB42_Gen2_v1.0_T1: temp=27.0 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45633 bytes_read=275848 bytes_retransmit=0 bytes_invalid=0 send_seq=3910 receive_seq=3910 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999860 adj=31998658 coil_temp=17.7 refs=0 mcu_temp=20.75 supply_voltage=3.012 th0: temp=37.3 th1: temp=38.9 th2: temp=41.2 th3: temp=39.4 sysload=0.31 cputime=27.424 memavail=7423864 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 191.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=176885 bytes_read=165178 bytes_retransmit=9 bytes_invalid=0 send_seq=9731 receive_seq=9731 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015314 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1810 bytes_read=7620 bytes_retransmit=0 bytes_invalid=0 send_seq=273 receive_seq=273 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999095 adj=49993002 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9312 bytes_read=33099 bytes_retransmit=9 bytes_invalid=0 send_seq=884 receive_seq=884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997810 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10902 bytes_read=35611 bytes_retransmit=9 bytes_invalid=0 send_seq=1016 receive_seq=1016 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999977 adj=63997560 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1969 bytes_read=43587 bytes_retransmit=9 bytes_invalid=0 send_seq=279 receive_seq=279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999478 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2563 bytes_read=7493 bytes_retransmit=9 bytes_invalid=0 send_seq=274 receive_seq=274 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999895 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.8 EBB42_Gen2_v1.0_T1: temp=27.0 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45639 bytes_read=276204 bytes_retransmit=0 bytes_invalid=0 send_seq=3911 receive_seq=3911 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999860 adj=31998649 coil_temp=17.7 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=37.2 th1: temp=38.4 th2: temp=41.4 th3: temp=39.4 sysload=0.36 cputime=27.490 memavail=7416936 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 192.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=177178 bytes_read=165624 bytes_retransmit=9 bytes_invalid=0 send_seq=9753 receive_seq=9753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015315 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1816 bytes_read=7636 bytes_retransmit=0 bytes_invalid=0 send_seq=274 receive_seq=274 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999027 adj=49992991 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9318 bytes_read=33199 bytes_retransmit=9 bytes_invalid=0 send_seq=885 receive_seq=885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997761 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10908 bytes_read=35711 bytes_retransmit=9 bytes_invalid=0 send_seq=1017 receive_seq=1017 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999978 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1975 bytes_read=43821 bytes_retransmit=9 bytes_invalid=0 send_seq=280 receive_seq=280 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999479 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2569 bytes_read=7520 bytes_retransmit=9 bytes_invalid=0 send_seq=275 receive_seq=275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999895 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=27.6 EBB42_Gen2_v1.0_T1: temp=27.1 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45645 bytes_read=276560 bytes_retransmit=0 bytes_invalid=0 send_seq=3912 receive_seq=3912 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999859 adj=31998634 coil_temp=17.7 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=37.2 th1: temp=38.4 th2: temp=41.3 th3: temp=39.6 sysload=0.36 cputime=27.561 memavail=7402204 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 193.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=177476 bytes_read=166046 bytes_retransmit=9 bytes_invalid=0 send_seq=9776 receive_seq=9776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015307 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1822 bytes_read=7652 bytes_retransmit=0 bytes_invalid=0 send_seq=275 receive_seq=275 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998958 adj=49992989 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9324 bytes_read=33299 bytes_retransmit=9 bytes_invalid=0 send_seq=886 receive_seq=886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997730 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10914 bytes_read=35811 bytes_retransmit=9 bytes_invalid=0 send_seq=1018 receive_seq=1018 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999978 adj=63997555 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1981 bytes_read=44115 bytes_retransmit=9 bytes_invalid=0 send_seq=281 receive_seq=281 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999478 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2575 bytes_read=7536 bytes_retransmit=9 bytes_invalid=0 send_seq=276 receive_seq=276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999895 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.5 EBB42_Gen2_v1.0_T1: temp=27.0 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45651 bytes_read=276916 bytes_retransmit=0 bytes_invalid=0 send_seq=3913 receive_seq=3913 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999859 adj=31998629 coil_temp=17.7 refs=0 mcu_temp=20.75 supply_voltage=3.011 th0: temp=37.5 th1: temp=38.4 th2: temp=41.6 th3: temp=39.2 sysload=0.36 cputime=27.603 memavail=7402204 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 194.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=177774 bytes_read=166471 bytes_retransmit=9 bytes_invalid=0 send_seq=9799 receive_seq=9799 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015307 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1828 bytes_read=7668 bytes_retransmit=0 bytes_invalid=0 send_seq=276 receive_seq=276 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998891 adj=49992981 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9330 bytes_read=33427 bytes_retransmit=9 bytes_invalid=0 send_seq=887 receive_seq=887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997797 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10920 bytes_read=35939 bytes_retransmit=9 bytes_invalid=0 send_seq=1019 receive_seq=1019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999978 adj=63997564 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1987 bytes_read=44364 bytes_retransmit=9 bytes_invalid=0 send_seq=282 receive_seq=282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999479 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2581 bytes_read=7552 bytes_retransmit=9 bytes_invalid=0 send_seq=277 receive_seq=277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999895 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=27.7 EBB42_Gen2_v1.0_T1: temp=27.0 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45657 bytes_read=277272 bytes_retransmit=0 bytes_invalid=0 send_seq=3914 receive_seq=3914 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999859 adj=31998638 coil_temp=17.7 refs=0 mcu_temp=20.76 supply_voltage=3.011 th0: temp=37.3 th1: temp=38.5 th2: temp=41.4 th3: temp=39.5 sysload=0.36 cputime=27.652 memavail=7398456 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 195.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=178072 bytes_read=166940 bytes_retransmit=9 bytes_invalid=0 send_seq=9822 receive_seq=9822 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015310 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1834 bytes_read=7684 bytes_retransmit=0 bytes_invalid=0 send_seq=277 receive_seq=277 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998826 adj=49992971 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9336 bytes_read=33541 bytes_retransmit=9 bytes_invalid=0 send_seq=888 receive_seq=888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997755 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10926 bytes_read=36053 bytes_retransmit=9 bytes_invalid=0 send_seq=1020 receive_seq=1020 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997568 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1993 bytes_read=44598 bytes_retransmit=9 bytes_invalid=0 send_seq=283 receive_seq=283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999479 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2587 bytes_read=7568 bytes_retransmit=9 bytes_invalid=0 send_seq=278 receive_seq=278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999895 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.7 EBB42_Gen2_v1.0_T1: temp=27.1 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45663 bytes_read=277628 bytes_retransmit=0 bytes_invalid=0 send_seq=3915 receive_seq=3915 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999859 adj=31998635 coil_temp=17.7 refs=0 mcu_temp=20.76 supply_voltage=3.011 th0: temp=36.7 th1: temp=38.7 th2: temp=41.5 th3: temp=39.3 sysload=0.36 cputime=27.711 memavail=7395188 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 196.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=178370 bytes_read=167365 bytes_retransmit=9 bytes_invalid=0 send_seq=9845 receive_seq=9845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015300 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1840 bytes_read=7713 bytes_retransmit=0 bytes_invalid=0 send_seq=278 receive_seq=278 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998766 adj=49992983 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9342 bytes_read=33641 bytes_retransmit=9 bytes_invalid=0 send_seq=889 receive_seq=889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997716 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10932 bytes_read=36153 bytes_retransmit=9 bytes_invalid=0 send_seq=1021 receive_seq=1021 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997608 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1999 bytes_read=44877 bytes_retransmit=9 bytes_invalid=0 send_seq=284 receive_seq=284 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999480 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2593 bytes_read=7584 bytes_retransmit=9 bytes_invalid=0 send_seq=279 receive_seq=279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999896 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.8 EBB42_Gen2_v1.0_T1: temp=27.1 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45669 bytes_read=277984 bytes_retransmit=0 bytes_invalid=0 send_seq=3916 receive_seq=3916 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999859 adj=31998628 coil_temp=17.7 refs=0 mcu_temp=20.75 supply_voltage=3.011 th0: temp=37.1 th1: temp=38.5 th2: temp=41.5 th3: temp=39.6 sysload=0.41 cputime=27.758 memavail=7394964 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 197.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=178668 bytes_read=167790 bytes_retransmit=9 bytes_invalid=0 send_seq=9868 receive_seq=9868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015296 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1846 bytes_read=7729 bytes_retransmit=0 bytes_invalid=0 send_seq=279 receive_seq=279 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998704 adj=49993052 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9348 bytes_read=33769 bytes_retransmit=9 bytes_invalid=0 send_seq=890 receive_seq=890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997716 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10938 bytes_read=36281 bytes_retransmit=9 bytes_invalid=0 send_seq=1022 receive_seq=1022 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997605 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2005 bytes_read=45126 bytes_retransmit=9 bytes_invalid=0 send_seq=285 receive_seq=285 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999479 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2599 bytes_read=7611 bytes_retransmit=9 bytes_invalid=0 send_seq=280 receive_seq=280 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999896 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=27.6 EBB42_Gen2_v1.0_T1: temp=27.0 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45675 bytes_read=278340 bytes_retransmit=0 bytes_invalid=0 send_seq=3917 receive_seq=3917 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999859 adj=31998636 coil_temp=17.7 refs=0 mcu_temp=20.75 supply_voltage=3.011 th0: temp=36.8 th1: temp=38.7 th2: temp=41.5 th3: temp=40.0 sysload=0.41 cputime=27.881 memavail=7393120 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 198.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=178966 bytes_read=168244 bytes_retransmit=9 bytes_invalid=0 send_seq=9891 receive_seq=9891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015296 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1852 bytes_read=7745 bytes_retransmit=0 bytes_invalid=0 send_seq=280 receive_seq=280 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998643 adj=49993058 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9354 bytes_read=33869 bytes_retransmit=9 bytes_invalid=0 send_seq=891 receive_seq=891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997718 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10944 bytes_read=36381 bytes_retransmit=9 bytes_invalid=0 send_seq=1023 receive_seq=1023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999981 adj=63997605 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2011 bytes_read=45375 bytes_retransmit=9 bytes_invalid=0 send_seq=286 receive_seq=286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999480 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2605 bytes_read=7627 bytes_retransmit=9 bytes_invalid=0 send_seq=281 receive_seq=281 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999899 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.0 EBB42_Gen2_v1.0_T0: temp=27.9 EBB42_Gen2_v1.0_T1: temp=27.0 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45681 bytes_read=278696 bytes_retransmit=0 bytes_invalid=0 send_seq=3918 receive_seq=3918 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999859 adj=31998648 coil_temp=17.7 refs=0 mcu_temp=20.75 supply_voltage=3.011 th0: temp=37.2 th1: temp=38.8 th2: temp=41.9 th3: temp=39.8 sysload=0.41 cputime=27.952 memavail=7393372 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 199.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=179264 bytes_read=168669 bytes_retransmit=9 bytes_invalid=0 send_seq=9914 receive_seq=9914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015295 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1858 bytes_read=7761 bytes_retransmit=0 bytes_invalid=0 send_seq=281 receive_seq=281 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998583 adj=49993060 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9360 bytes_read=33983 bytes_retransmit=9 bytes_invalid=0 send_seq=892 receive_seq=892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997712 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10950 bytes_read=36481 bytes_retransmit=9 bytes_invalid=0 send_seq=1024 receive_seq=1024 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999981 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2017 bytes_read=45654 bytes_retransmit=9 bytes_invalid=0 send_seq=287 receive_seq=287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999481 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2611 bytes_read=7643 bytes_retransmit=9 bytes_invalid=0 send_seq=282 receive_seq=282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999493 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.7 EBB42_Gen2_v1.0_T1: temp=27.0 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45687 bytes_read=279052 bytes_retransmit=0 bytes_invalid=0 send_seq=3919 receive_seq=3919 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999859 adj=31998648 coil_temp=17.7 refs=0 mcu_temp=20.76 supply_voltage=3.011 th0: temp=37.1 th1: temp=39.3 th2: temp=41.6 th3: temp=39.8 sysload=0.41 cputime=27.996 memavail=7391104 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 200.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=179562 bytes_read=169109 bytes_retransmit=9 bytes_invalid=0 send_seq=9937 receive_seq=9937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015303 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1864 bytes_read=7777 bytes_retransmit=0 bytes_invalid=0 send_seq=282 receive_seq=282 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998527 adj=49993054 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9366 bytes_read=34111 bytes_retransmit=9 bytes_invalid=0 send_seq=893 receive_seq=893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997695 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10956 bytes_read=36623 bytes_retransmit=9 bytes_invalid=0 send_seq=1025 receive_seq=1025 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999983 adj=63997567 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2023 bytes_read=45903 bytes_retransmit=9 bytes_invalid=0 send_seq=288 receive_seq=288 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999483 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2617 bytes_read=7659 bytes_retransmit=9 bytes_invalid=0 send_seq=283 receive_seq=283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999476 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=28.0 EBB42_Gen2_v1.0_T1: temp=27.1 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45693 bytes_read=279408 bytes_retransmit=0 bytes_invalid=0 send_seq=3920 receive_seq=3920 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999860 adj=31998645 coil_temp=17.7 refs=0 mcu_temp=20.76 supply_voltage=3.011 th0: temp=37.3 th1: temp=38.7 th2: temp=41.8 th3: temp=39.9 sysload=0.41 cputime=28.042 memavail=7392712 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 201.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=179860 bytes_read=169563 bytes_retransmit=9 bytes_invalid=0 send_seq=9960 receive_seq=9960 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015301 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1870 bytes_read=7806 bytes_retransmit=0 bytes_invalid=0 send_seq=283 receive_seq=283 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998471 adj=49993079 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9372 bytes_read=34211 bytes_retransmit=9 bytes_invalid=0 send_seq=894 receive_seq=894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997759 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10962 bytes_read=36723 bytes_retransmit=9 bytes_invalid=0 send_seq=1026 receive_seq=1026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997560 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2029 bytes_read=46137 bytes_retransmit=9 bytes_invalid=0 send_seq=289 receive_seq=289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999483 adj=47997696 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2623 bytes_read=7675 bytes_retransmit=9 bytes_invalid=0 send_seq=284 receive_seq=284 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=28.0 EBB42_Gen2_v1.0_T1: temp=27.0 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45699 bytes_read=279764 bytes_retransmit=0 bytes_invalid=0 send_seq=3921 receive_seq=3921 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999861 adj=31998649 coil_temp=17.6 refs=0 mcu_temp=20.75 supply_voltage=3.011 th0: temp=37.0 th1: temp=39.0 th2: temp=41.8 th3: temp=39.9 sysload=0.38 cputime=28.085 memavail=7391956 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 202.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=180158 bytes_read=169988 bytes_retransmit=9 bytes_invalid=0 send_seq=9983 receive_seq=9983 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015300 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1876 bytes_read=7822 bytes_retransmit=0 bytes_invalid=0 send_seq=284 receive_seq=284 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998417 adj=49993109 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9378 bytes_read=34325 bytes_retransmit=9 bytes_invalid=0 send_seq=895 receive_seq=895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997736 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10968 bytes_read=36837 bytes_retransmit=9 bytes_invalid=0 send_seq=1027 receive_seq=1027 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2035 bytes_read=46431 bytes_retransmit=9 bytes_invalid=0 send_seq=290 receive_seq=290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999482 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2629 bytes_read=7702 bytes_retransmit=9 bytes_invalid=0 send_seq=285 receive_seq=285 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.9 EBB42_Gen2_v1.0_T1: temp=27.0 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45705 bytes_read=280120 bytes_retransmit=0 bytes_invalid=0 send_seq=3922 receive_seq=3922 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999866 adj=31998654 coil_temp=17.7 refs=0 mcu_temp=20.74 supply_voltage=3.011 th0: temp=37.6 th1: temp=39.0 th2: temp=41.8 th3: temp=39.9 sysload=0.38 cputime=28.127 memavail=7391956 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Stats 203.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=180456 bytes_read=170411 bytes_retransmit=9 bytes_invalid=0 send_seq=10006 receive_seq=10006 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015302 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1882 bytes_read=7838 bytes_retransmit=0 bytes_invalid=0 send_seq=285 receive_seq=285 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998366 adj=49993149 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9384 bytes_read=34439 bytes_retransmit=9 bytes_invalid=0 send_seq=896 receive_seq=896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997717 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10974 bytes_read=36951 bytes_retransmit=9 bytes_invalid=0 send_seq=1028 receive_seq=1028 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997549 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2041 bytes_read=46680 bytes_retransmit=9 bytes_invalid=0 send_seq=291 receive_seq=291 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999483 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2635 bytes_read=7718 bytes_retransmit=9 bytes_invalid=0 send_seq=286 receive_seq=286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.9 EBB42_Gen2_v1.0_T1: temp=26.8 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45711 bytes_read=280476 bytes_retransmit=0 bytes_invalid=0 send_seq=3923 receive_seq=3923 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999867 adj=31998728 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.011 th0: temp=37.2 th1: temp=38.7 th2: temp=41.8 th3: temp=40.1 sysload=0.38 cputime=28.170 memavail=7391956 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 204.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=180754 bytes_read=170862 bytes_retransmit=9 bytes_invalid=0 send_seq=10029 receive_seq=10029 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015301 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1888 bytes_read=7854 bytes_retransmit=0 bytes_invalid=0 send_seq=286 receive_seq=286 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998317 adj=49993195 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9390 bytes_read=34539 bytes_retransmit=9 bytes_invalid=0 send_seq=897 receive_seq=897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997803 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10980 bytes_read=37051 bytes_retransmit=9 bytes_invalid=0 send_seq=1029 receive_seq=1029 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2047 bytes_read=46914 bytes_retransmit=9 bytes_invalid=0 send_seq=292 receive_seq=292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999483 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2641 bytes_read=7734 bytes_retransmit=9 bytes_invalid=0 send_seq=287 receive_seq=287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.7 EBB42_Gen2_v1.0_T1: temp=26.9 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45717 bytes_read=280832 bytes_retransmit=0 bytes_invalid=0 send_seq=3924 receive_seq=3924 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999868 adj=31998721 coil_temp=17.6 refs=0 mcu_temp=20.75 supply_voltage=3.012 th0: temp=36.9 th1: temp=38.7 th2: temp=41.6 th3: temp=39.9 sysload=0.38 cputime=28.215 memavail=7391956 print_time=198.915 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Extruder extruder already active
Extruder 'extruder' now syncing with 'extruder'
Extruder 'extruder1' now syncing with 'extruder'
RatOS | SET_PRESSURE_ADVANCE:: T0
extruder: pressure_advance: 0.008000
pressure_advance_smooth_time: 0.040000
RatOS | SET_PRESSURE_ADVANCE:: T1
extruder1: pressure_advance: 0.008000
pressure_advance_smooth_time: 0.040000
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 205.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=184393 bytes_read=171562 bytes_retransmit=9 bytes_invalid=0 send_seq=10104 receive_seq=10104 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015315 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1894 bytes_read=7870 bytes_retransmit=0 bytes_invalid=0 send_seq=287 receive_seq=287 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998269 adj=49993245 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9396 bytes_read=34667 bytes_retransmit=9 bytes_invalid=0 send_seq=898 receive_seq=898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997771 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10986 bytes_read=37179 bytes_retransmit=9 bytes_invalid=0 send_seq=1030 receive_seq=1030 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997534 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2053 bytes_read=47208 bytes_retransmit=9 bytes_invalid=0 send_seq=293 receive_seq=293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999482 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2647 bytes_read=7750 bytes_retransmit=9 bytes_invalid=0 send_seq=288 receive_seq=288 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=27.9 EBB42_Gen2_v1.0_T1: temp=27.0 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45723 bytes_read=281188 bytes_retransmit=0 bytes_invalid=0 send_seq=3925 receive_seq=3925 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999867 adj=31998724 coil_temp=17.6 refs=0 mcu_temp=20.75 supply_voltage=3.012 th0: temp=36.4 th1: temp=38.9 th2: temp=41.9 th3: temp=39.9 sysload=0.38 cputime=28.330 memavail=7391756 print_time=228.218 buffer_time=0.742 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 206.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=184691 bytes_read=171987 bytes_retransmit=9 bytes_invalid=0 send_seq=10127 receive_seq=10127 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015337 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1900 bytes_read=7886 bytes_retransmit=0 bytes_invalid=0 send_seq=288 receive_seq=288 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998224 adj=49993869 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9402 bytes_read=34781 bytes_retransmit=9 bytes_invalid=0 send_seq=899 receive_seq=899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997696 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10992 bytes_read=37293 bytes_retransmit=9 bytes_invalid=0 send_seq=1031 receive_seq=1031 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997512 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2059 bytes_read=47442 bytes_retransmit=9 bytes_invalid=0 send_seq=294 receive_seq=294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999482 adj=47997621 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2653 bytes_read=7766 bytes_retransmit=9 bytes_invalid=0 send_seq=289 receive_seq=289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=27.9 EBB42_Gen2_v1.0_T1: temp=27.1 raspberry_pi: temp=21.9  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45729 bytes_read=281544 bytes_retransmit=0 bytes_invalid=0 send_seq=3926 receive_seq=3926 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999867 adj=31998661 coil_temp=17.6 refs=0 mcu_temp=20.76 supply_voltage=3.012 th0: temp=36.6 th1: temp=38.7 th2: temp=41.7 th3: temp=40.3 sysload=0.35 cputime=28.373 memavail=7391756 print_time=228.218 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 207.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=184989 bytes_read=172441 bytes_retransmit=9 bytes_invalid=0 send_seq=10150 receive_seq=10150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015331 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1906 bytes_read=7915 bytes_retransmit=0 bytes_invalid=0 send_seq=289 receive_seq=289 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998180 adj=49993278 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9408 bytes_read=34881 bytes_retransmit=9 bytes_invalid=0 send_seq=900 receive_seq=900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997621 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=10998 bytes_read=37393 bytes_retransmit=9 bytes_invalid=0 send_seq=1032 receive_seq=1032 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997458 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2065 bytes_read=47676 bytes_retransmit=9 bytes_invalid=0 send_seq=295 receive_seq=295 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999481 adj=47997574 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2659 bytes_read=7793 bytes_retransmit=9 bytes_invalid=0 send_seq=290 receive_seq=290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=27.9 EBB42_Gen2_v1.0_T1: temp=27.1 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45735 bytes_read=281900 bytes_retransmit=0 bytes_invalid=0 send_seq=3927 receive_seq=3927 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999868 adj=31998620 coil_temp=17.6 refs=0 mcu_temp=20.75 supply_voltage=3.012 th0: temp=36.9 th1: temp=39.2 th2: temp=42.2 th3: temp=39.9 sysload=0.35 cputime=28.416 memavail=7391756 print_time=228.218 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 208.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=185287 bytes_read=172866 bytes_retransmit=9 bytes_invalid=0 send_seq=10173 receive_seq=10173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015326 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1912 bytes_read=7931 bytes_retransmit=0 bytes_invalid=0 send_seq=290 receive_seq=290 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998137 adj=49993360 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9414 bytes_read=34995 bytes_retransmit=9 bytes_invalid=0 send_seq=901 receive_seq=901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997635 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11004 bytes_read=37507 bytes_retransmit=9 bytes_invalid=0 send_seq=1033 receive_seq=1033 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997485 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2071 bytes_read=47985 bytes_retransmit=9 bytes_invalid=0 send_seq=296 receive_seq=296 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999481 adj=47997591 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2665 bytes_read=7809 bytes_retransmit=9 bytes_invalid=0 send_seq=291 receive_seq=291 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=27.9 EBB42_Gen2_v1.0_T1: temp=27.4 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45741 bytes_read=282256 bytes_retransmit=0 bytes_invalid=0 send_seq=3928 receive_seq=3928 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999870 adj=31998658 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=37.4 th1: temp=39.4 th2: temp=42.2 th3: temp=40.1 sysload=0.35 cputime=28.459 memavail=7391756 print_time=228.218 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 209.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=185585 bytes_read=173291 bytes_retransmit=9 bytes_invalid=0 send_seq=10196 receive_seq=10196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015318 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1918 bytes_read=7947 bytes_retransmit=0 bytes_invalid=0 send_seq=291 receive_seq=291 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998098 adj=49993440 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9420 bytes_read=35109 bytes_retransmit=9 bytes_invalid=0 send_seq=902 receive_seq=902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997660 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11010 bytes_read=37621 bytes_retransmit=9 bytes_invalid=0 send_seq=1034 receive_seq=1034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999981 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2077 bytes_read=48219 bytes_retransmit=9 bytes_invalid=0 send_seq=297 receive_seq=297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999481 adj=47997608 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2671 bytes_read=7825 bytes_retransmit=9 bytes_invalid=0 send_seq=292 receive_seq=292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=28.0 EBB42_Gen2_v1.0_T1: temp=27.3 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45747 bytes_read=282612 bytes_retransmit=0 bytes_invalid=0 send_seq=3929 receive_seq=3929 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999869 adj=31998681 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=37.3 th1: temp=38.8 th2: temp=42.0 th3: temp=40.2 sysload=0.35 cputime=28.502 memavail=7391772 print_time=228.218 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 210.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=185883 bytes_read=173760 bytes_retransmit=9 bytes_invalid=0 send_seq=10219 receive_seq=10219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015308 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1924 bytes_read=7963 bytes_retransmit=0 bytes_invalid=0 send_seq=292 receive_seq=292 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998060 adj=49993540 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9426 bytes_read=35223 bytes_retransmit=9 bytes_invalid=0 send_seq=903 receive_seq=903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997673 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11016 bytes_read=37735 bytes_retransmit=9 bytes_invalid=0 send_seq=1035 receive_seq=1035 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999981 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2083 bytes_read=48453 bytes_retransmit=9 bytes_invalid=0 send_seq=298 receive_seq=298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999480 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2677 bytes_read=7841 bytes_retransmit=9 bytes_invalid=0 send_seq=293 receive_seq=293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=27.9 EBB42_Gen2_v1.0_T1: temp=27.2 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45753 bytes_read=282968 bytes_retransmit=0 bytes_invalid=0 send_seq=3930 receive_seq=3930 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999869 adj=31998673 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=37.4 th1: temp=38.7 th2: temp=41.8 th3: temp=40.1 sysload=0.35 cputime=28.545 memavail=7391772 print_time=228.218 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 211.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=186181 bytes_read=174185 bytes_retransmit=9 bytes_invalid=0 send_seq=10242 receive_seq=10242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015330 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1930 bytes_read=7979 bytes_retransmit=0 bytes_invalid=0 send_seq=293 receive_seq=293 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998024 adj=49993632 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9432 bytes_read=35337 bytes_retransmit=9 bytes_invalid=0 send_seq=904 receive_seq=904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997766 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11022 bytes_read=37849 bytes_retransmit=9 bytes_invalid=0 send_seq=1036 receive_seq=1036 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999982 adj=63997548 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2089 bytes_read=48747 bytes_retransmit=9 bytes_invalid=0 send_seq=299 receive_seq=299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999480 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2683 bytes_read=7857 bytes_retransmit=9 bytes_invalid=0 send_seq=294 receive_seq=294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=27.9 EBB42_Gen2_v1.0_T1: temp=27.1 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45759 bytes_read=283324 bytes_retransmit=0 bytes_invalid=0 send_seq=3931 receive_seq=3931 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999869 adj=31998674 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=37.7 th1: temp=38.7 th2: temp=42.3 th3: temp=40.2 sysload=0.32 cputime=28.589 memavail=7391772 print_time=228.218 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 212.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=186479 bytes_read=174610 bytes_retransmit=9 bytes_invalid=0 send_seq=10265 receive_seq=10265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015350 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1936 bytes_read=8008 bytes_retransmit=0 bytes_invalid=0 send_seq=294 receive_seq=294 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997989 adj=49993659 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9438 bytes_read=35451 bytes_retransmit=9 bytes_invalid=0 send_seq=905 receive_seq=905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997699 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11028 bytes_read=37963 bytes_retransmit=9 bytes_invalid=0 send_seq=1037 receive_seq=1037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999984 adj=63997502 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2095 bytes_read=48981 bytes_retransmit=9 bytes_invalid=0 send_seq=300 receive_seq=300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999480 adj=47997602 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2689 bytes_read=7884 bytes_retransmit=9 bytes_invalid=0 send_seq=295 receive_seq=295 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.7 EBB42_Gen2_v1.0_T1: temp=27.0 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45765 bytes_read=283680 bytes_retransmit=0 bytes_invalid=0 send_seq=3932 receive_seq=3932 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999870 adj=31998650 coil_temp=17.6 refs=0 mcu_temp=20.73 supply_voltage=3.012 th0: temp=36.7 th1: temp=38.8 th2: temp=42.1 th3: temp=40.5 sysload=0.32 cputime=28.632 memavail=7391772 print_time=228.218 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 213.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=186777 bytes_read=175064 bytes_retransmit=9 bytes_invalid=0 send_seq=10288 receive_seq=10288 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015397 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1942 bytes_read=8024 bytes_retransmit=0 bytes_invalid=0 send_seq=295 receive_seq=295 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997957 adj=49993694 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9444 bytes_read=35551 bytes_retransmit=9 bytes_invalid=0 send_seq=906 receive_seq=906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997638 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11034 bytes_read=38063 bytes_retransmit=9 bytes_invalid=0 send_seq=1038 receive_seq=1038 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999986 adj=63997491 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2101 bytes_read=49230 bytes_retransmit=9 bytes_invalid=0 send_seq=301 receive_seq=301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999480 adj=47997570 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2695 bytes_read=7900 bytes_retransmit=9 bytes_invalid=0 send_seq=296 receive_seq=296 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999422 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=27.8 EBB42_Gen2_v1.0_T1: temp=27.3 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45771 bytes_read=284036 bytes_retransmit=0 bytes_invalid=0 send_seq=3933 receive_seq=3933 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31998637 coil_temp=17.6 refs=0 mcu_temp=20.73 supply_voltage=3.012 th0: temp=37.0 th1: temp=38.6 th2: temp=42.2 th3: temp=40.4 sysload=0.32 cputime=28.675 memavail=7391772 print_time=228.218 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 214.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=187075 bytes_read=175485 bytes_retransmit=9 bytes_invalid=0 send_seq=10311 receive_seq=10311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015396 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1948 bytes_read=8040 bytes_retransmit=0 bytes_invalid=0 send_seq=296 receive_seq=296 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997926 adj=49993693 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9450 bytes_read=35665 bytes_retransmit=9 bytes_invalid=0 send_seq=907 receive_seq=907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997532 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11040 bytes_read=38177 bytes_retransmit=9 bytes_invalid=0 send_seq=1039 receive_seq=1039 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999985 adj=63997411 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2107 bytes_read=49524 bytes_retransmit=9 bytes_invalid=0 send_seq=302 receive_seq=302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999480 adj=47997506 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2701 bytes_read=7916 bytes_retransmit=9 bytes_invalid=0 send_seq=297 receive_seq=297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999403 Octopus_Pro_H723_V1.1: temp=28.1 EBB42_Gen2_v1.0_T0: temp=27.9 EBB42_Gen2_v1.0_T1: temp=27.2 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45777 bytes_read=284392 bytes_retransmit=0 bytes_invalid=0 send_seq=3934 receive_seq=3934 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31998604 coil_temp=17.6 refs=0 mcu_temp=20.73 supply_voltage=3.012 th0: temp=37.5 th1: temp=38.7 th2: temp=42.6 th3: temp=40.3 sysload=0.32 cputime=28.721 memavail=7391772 print_time=228.218 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 215.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=187373 bytes_read=175924 bytes_retransmit=9 bytes_invalid=0 send_seq=10334 receive_seq=10334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015389 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1954 bytes_read=8056 bytes_retransmit=0 bytes_invalid=0 send_seq=297 receive_seq=297 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997896 adj=49993801 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=9456 bytes_read=35793 bytes_retransmit=9 bytes_invalid=0 send_seq=908 receive_seq=908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997563 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=11046 bytes_read=38305 bytes_retransmit=9 bytes_invalid=0 send_seq=1040 receive_seq=1040 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999985 adj=63997436 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2113 bytes_read=49758 bytes_retransmit=9 bytes_invalid=0 send_seq=303 receive_seq=303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999480 adj=47997538 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2707 bytes_read=7932 bytes_retransmit=9 bytes_invalid=0 send_seq=298 receive_seq=298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999413 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=27.9 EBB42_Gen2_v1.0_T1: temp=27.3 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45783 bytes_read=284748 bytes_retransmit=0 bytes_invalid=0 send_seq=3935 receive_seq=3935 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999870 adj=31998605 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=37.4 th1: temp=38.4 th2: temp=42.6 th3: temp=40.5 sysload=0.32 cputime=28.767 memavail=7391820 print_time=228.218 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 216.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=188028 bytes_read=176408 bytes_retransmit=9 bytes_invalid=0 send_seq=10363 receive_seq=10363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=0 freq=400015389 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1960 bytes_read=8072 bytes_retransmit=0 bytes_invalid=0 send_seq=298 receive_seq=298 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997870 adj=49993903 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=9462 bytes_read=35893 bytes_retransmit=9 bytes_invalid=0 send_seq=909 receive_seq=909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997598 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=11052 bytes_read=38405 bytes_retransmit=9 bytes_invalid=0 send_seq=1041 receive_seq=1041 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999987 adj=63997468 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2119 bytes_read=49992 bytes_retransmit=9 bytes_invalid=0 send_seq=304 receive_seq=304 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999480 adj=47997573 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2713 bytes_read=7948 bytes_retransmit=9 bytes_invalid=0 send_seq=299 receive_seq=299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999421 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=28.1 EBB42_Gen2_v1.0_T1: temp=27.3 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45789 bytes_read=285104 bytes_retransmit=0 bytes_invalid=0 send_seq=3936 receive_seq=3936 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999869 adj=31998606 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=38.1 th1: temp=38.5 th2: temp=42.3 th3: temp=40.9 sysload=0.30 cputime=28.830 memavail=7391820 print_time=240.376 buffer_time=1.897 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 217.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=188380 bytes_read=176833 bytes_retransmit=9 bytes_invalid=0 send_seq=10386 receive_seq=10386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015407 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1966 bytes_read=8101 bytes_retransmit=0 bytes_invalid=0 send_seq=299 receive_seq=299 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997846 adj=49995128 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=9468 bytes_read=36007 bytes_retransmit=9 bytes_invalid=0 send_seq=910 receive_seq=910 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997671 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=11058 bytes_read=38519 bytes_retransmit=9 bytes_invalid=0 send_seq=1042 receive_seq=1042 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999987 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2125 bytes_read=50286 bytes_retransmit=9 bytes_invalid=0 send_seq=305 receive_seq=305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999481 adj=47997618 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2719 bytes_read=7975 bytes_retransmit=9 bytes_invalid=0 send_seq=300 receive_seq=300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=27.9 EBB42_Gen2_v1.0_T1: temp=27.2 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45795 bytes_read=285460 bytes_retransmit=0 bytes_invalid=0 send_seq=3937 receive_seq=3937 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31998618 coil_temp=17.6 refs=0 mcu_temp=20.75 supply_voltage=3.012 th0: temp=37.4 th1: temp=38.5 th2: temp=42.4 th3: temp=40.5 sysload=0.30 cputime=28.881 memavail=7394196 print_time=240.376 buffer_time=0.897 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 218.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=188910 bytes_read=177278 bytes_retransmit=9 bytes_invalid=0 send_seq=10413 receive_seq=10413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015399 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1972 bytes_read=8117 bytes_retransmit=0 bytes_invalid=0 send_seq=300 receive_seq=300 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997823 adj=49994783 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=9474 bytes_read=36121 bytes_retransmit=9 bytes_invalid=0 send_seq=911 receive_seq=911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997621 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=11064 bytes_read=38633 bytes_retransmit=9 bytes_invalid=0 send_seq=1043 receive_seq=1043 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999987 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2131 bytes_read=50535 bytes_retransmit=9 bytes_invalid=0 send_seq=306 receive_seq=306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999480 adj=47997600 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2725 bytes_read=7991 bytes_retransmit=9 bytes_invalid=0 send_seq=301 receive_seq=301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=27.7 EBB42_Gen2_v1.0_T1: temp=27.3 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45801 bytes_read=285816 bytes_retransmit=0 bytes_invalid=0 send_seq=3938 receive_seq=3938 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999875 adj=31998620 coil_temp=17.6 refs=0 mcu_temp=20.76 supply_voltage=3.012 th0: temp=37.3 th1: temp=38.6 th2: temp=42.3 th3: temp=40.5 sysload=0.30 cputime=28.924 memavail=7394196 print_time=240.376 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 219.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=189208 bytes_read=177732 bytes_retransmit=9 bytes_invalid=0 send_seq=10436 receive_seq=10436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015401 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1978 bytes_read=8133 bytes_retransmit=0 bytes_invalid=0 send_seq=301 receive_seq=301 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997801 adj=49994468 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=9480 bytes_read=36221 bytes_retransmit=9 bytes_invalid=0 send_seq=912 receive_seq=912 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997662 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=11070 bytes_read=38733 bytes_retransmit=9 bytes_invalid=0 send_seq=1044 receive_seq=1044 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999988 adj=63997514 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2137 bytes_read=50769 bytes_retransmit=9 bytes_invalid=0 send_seq=307 receive_seq=307 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999480 adj=47997611 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2731 bytes_read=8007 bytes_retransmit=9 bytes_invalid=0 send_seq=302 receive_seq=302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=28.1 EBB42_Gen2_v1.0_T1: temp=27.3 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45807 bytes_read=286172 bytes_retransmit=0 bytes_invalid=0 send_seq=3939 receive_seq=3939 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999876 adj=31998685 coil_temp=17.6 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=37.1 th1: temp=38.4 th2: temp=42.0 th3: temp=40.4 sysload=0.30 cputime=28.967 memavail=7394196 print_time=240.376 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 220.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=189506 bytes_read=178172 bytes_retransmit=9 bytes_invalid=0 send_seq=10459 receive_seq=10459 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015392 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1984 bytes_read=8149 bytes_retransmit=0 bytes_invalid=0 send_seq=302 receive_seq=302 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997780 adj=49994255 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9486 bytes_read=36349 bytes_retransmit=9 bytes_invalid=0 send_seq=913 receive_seq=913 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997678 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11076 bytes_read=38861 bytes_retransmit=9 bytes_invalid=0 send_seq=1045 receive_seq=1045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999988 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2143 bytes_read=51063 bytes_retransmit=9 bytes_invalid=0 send_seq=308 receive_seq=308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999480 adj=47997606 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2737 bytes_read=8023 bytes_retransmit=9 bytes_invalid=0 send_seq=303 receive_seq=303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=28.0 EBB42_Gen2_v1.0_T1: temp=27.3 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45813 bytes_read=286528 bytes_retransmit=0 bytes_invalid=0 send_seq=3940 receive_seq=3940 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999877 adj=31998706 coil_temp=17.6 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=37.8 th1: temp=38.6 th2: temp=42.4 th3: temp=40.3 sysload=0.30 cputime=29.010 memavail=7394196 print_time=240.376 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 221.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=189804 bytes_read=178597 bytes_retransmit=9 bytes_invalid=0 send_seq=10482 receive_seq=10482 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015386 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1990 bytes_read=8165 bytes_retransmit=0 bytes_invalid=0 send_seq=303 receive_seq=303 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997761 adj=49994344 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9492 bytes_read=36463 bytes_retransmit=9 bytes_invalid=0 send_seq=914 receive_seq=914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997689 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11082 bytes_read=38975 bytes_retransmit=9 bytes_invalid=0 send_seq=1046 receive_seq=1046 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999987 adj=63997545 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2149 bytes_read=51297 bytes_retransmit=9 bytes_invalid=0 send_seq=309 receive_seq=309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999481 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2743 bytes_read=8039 bytes_retransmit=9 bytes_invalid=0 send_seq=304 receive_seq=304 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=27.8 EBB42_Gen2_v1.0_T1: temp=27.3 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45819 bytes_read=286884 bytes_retransmit=0 bytes_invalid=0 send_seq=3941 receive_seq=3941 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999876 adj=31998707 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=37.8 th1: temp=38.7 th2: temp=42.2 th3: temp=40.4 sysload=0.35 cputime=29.066 memavail=7399524 print_time=240.376 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 222.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=190102 bytes_read=179051 bytes_retransmit=9 bytes_invalid=0 send_seq=10505 receive_seq=10505 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015384 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1996 bytes_read=8194 bytes_retransmit=0 bytes_invalid=0 send_seq=304 receive_seq=304 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997748 adj=49994440 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9498 bytes_read=36563 bytes_retransmit=9 bytes_invalid=0 send_seq=915 receive_seq=915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997700 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11088 bytes_read=39075 bytes_retransmit=9 bytes_invalid=0 send_seq=1047 receive_seq=1047 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999988 adj=63997544 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2155 bytes_read=51531 bytes_retransmit=9 bytes_invalid=0 send_seq=310 receive_seq=310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999480 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2749 bytes_read=8066 bytes_retransmit=9 bytes_invalid=0 send_seq=305 receive_seq=305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.0 EBB42_Gen2_v1.0_T1: temp=27.1 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45825 bytes_read=287240 bytes_retransmit=0 bytes_invalid=0 send_seq=3942 receive_seq=3942 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999877 adj=31998681 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=38.3 th1: temp=38.7 th2: temp=42.4 th3: temp=40.2 sysload=0.35 cputime=29.112 memavail=7395752 print_time=240.376 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 223.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=190400 bytes_read=179476 bytes_retransmit=9 bytes_invalid=0 send_seq=10528 receive_seq=10528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015384 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2002 bytes_read=8210 bytes_retransmit=0 bytes_invalid=0 send_seq=305 receive_seq=305 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997732 adj=49994588 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9504 bytes_read=36677 bytes_retransmit=9 bytes_invalid=0 send_seq=916 receive_seq=916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000181 adj=63997704 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11094 bytes_read=39189 bytes_retransmit=9 bytes_invalid=0 send_seq=1048 receive_seq=1048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999988 adj=63997567 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2161 bytes_read=51840 bytes_retransmit=9 bytes_invalid=0 send_seq=311 receive_seq=311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999480 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2755 bytes_read=8082 bytes_retransmit=9 bytes_invalid=0 send_seq=306 receive_seq=306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.1 EBB42_Gen2_v1.0_T1: temp=27.5 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45831 bytes_read=287596 bytes_retransmit=0 bytes_invalid=0 send_seq=3943 receive_seq=3943 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999876 adj=31998703 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=38.4 th1: temp=39.1 th2: temp=42.2 th3: temp=40.0 sysload=0.35 cputime=29.160 memavail=7396196 print_time=240.376 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 224.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=190698 bytes_read=179901 bytes_retransmit=9 bytes_invalid=0 send_seq=10551 receive_seq=10551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015383 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2008 bytes_read=8226 bytes_retransmit=0 bytes_invalid=0 send_seq=306 receive_seq=306 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997718 adj=49994659 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9510 bytes_read=36791 bytes_retransmit=9 bytes_invalid=0 send_seq=917 receive_seq=917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997689 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11100 bytes_read=39303 bytes_retransmit=9 bytes_invalid=0 send_seq=1049 receive_seq=1049 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999988 adj=63997548 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2167 bytes_read=52074 bytes_retransmit=9 bytes_invalid=0 send_seq=312 receive_seq=312 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999481 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2761 bytes_read=8098 bytes_retransmit=9 bytes_invalid=0 send_seq=307 receive_seq=307 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=27.9 EBB42_Gen2_v1.0_T1: temp=27.2 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45837 bytes_read=287952 bytes_retransmit=0 bytes_invalid=0 send_seq=3944 receive_seq=3944 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999875 adj=31998667 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=38.4 th1: temp=39.0 th2: temp=42.1 th3: temp=40.1 sysload=0.35 cputime=29.219 memavail=7393252 print_time=240.376 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Stats 225.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=190991 bytes_read=180359 bytes_retransmit=9 bytes_invalid=0 send_seq=10573 receive_seq=10573 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015381 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2014 bytes_read=8242 bytes_retransmit=0 bytes_invalid=0 send_seq=307 receive_seq=307 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997709 adj=49994730 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9516 bytes_read=36905 bytes_retransmit=9 bytes_invalid=0 send_seq=918 receive_seq=918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000179 adj=63997681 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11106 bytes_read=39417 bytes_retransmit=9 bytes_invalid=0 send_seq=1050 receive_seq=1050 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999988 adj=63997545 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2173 bytes_read=52308 bytes_retransmit=9 bytes_invalid=0 send_seq=313 receive_seq=313 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999481 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2767 bytes_read=8114 bytes_retransmit=9 bytes_invalid=0 send_seq=308 receive_seq=308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=28.2 EBB42_Gen2_v1.0_T1: temp=27.3 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45843 bytes_read=288308 bytes_retransmit=0 bytes_invalid=0 send_seq=3945 receive_seq=3945 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999875 adj=31998650 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=38.5 th1: temp=39.1 th2: temp=42.0 th3: temp=40.2 sysload=0.35 cputime=29.267 memavail=7390772 print_time=240.376 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 226.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=191269 bytes_read=180764 bytes_retransmit=9 bytes_invalid=0 send_seq=10592 receive_seq=10592 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015375 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2020 bytes_read=8258 bytes_retransmit=0 bytes_invalid=0 send_seq=308 receive_seq=308 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997696 adj=49994861 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9522 bytes_read=37019 bytes_retransmit=9 bytes_invalid=0 send_seq=919 receive_seq=919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997681 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11112 bytes_read=39531 bytes_retransmit=9 bytes_invalid=0 send_seq=1051 receive_seq=1051 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63997546 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2179 bytes_read=52602 bytes_retransmit=9 bytes_invalid=0 send_seq=314 receive_seq=314 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999483 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2773 bytes_read=8130 bytes_retransmit=9 bytes_invalid=0 send_seq=309 receive_seq=309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=28.1 EBB42_Gen2_v1.0_T1: temp=27.4 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45849 bytes_read=288655 bytes_retransmit=0 bytes_invalid=0 send_seq=3946 receive_seq=3946 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31998645 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=38.9 th1: temp=39.3 th2: temp=41.9 th3: temp=40.0 sysload=0.32 cputime=29.309 memavail=7390772 print_time=240.376 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 227.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=191567 bytes_read=181189 bytes_retransmit=9 bytes_invalid=0 send_seq=10615 receive_seq=10615 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015370 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=2026 bytes_read=8287 bytes_retransmit=0 bytes_invalid=0 send_seq=309 receive_seq=309 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997685 adj=49994900 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9528 bytes_read=37133 bytes_retransmit=9 bytes_invalid=0 send_seq=920 receive_seq=920 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000177 adj=63997691 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11118 bytes_read=39645 bytes_retransmit=9 bytes_invalid=0 send_seq=1052 receive_seq=1052 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63997569 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2185 bytes_read=52836 bytes_retransmit=9 bytes_invalid=0 send_seq=315 receive_seq=315 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999482 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2779 bytes_read=8157 bytes_retransmit=9 bytes_invalid=0 send_seq=310 receive_seq=310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.1 EBB42_Gen2_v1.0_T1: temp=27.5 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45855 bytes_read=289000 bytes_retransmit=0 bytes_invalid=0 send_seq=3947 receive_seq=3947 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31998639 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.011 th0: temp=38.9 th1: temp=39.2 th2: temp=41.9 th3: temp=39.9 sysload=0.32 cputime=29.351 memavail=7390776 print_time=240.376 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 228.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=191860 bytes_read=181638 bytes_retransmit=9 bytes_invalid=0 send_seq=10637 receive_seq=10637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015366 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=2032 bytes_read=8303 bytes_retransmit=0 bytes_invalid=0 send_seq=310 receive_seq=310 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997674 adj=49994945 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9534 bytes_read=37233 bytes_retransmit=9 bytes_invalid=0 send_seq=921 receive_seq=921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000177 adj=63997697 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11124 bytes_read=39745 bytes_retransmit=9 bytes_invalid=0 send_seq=1053 receive_seq=1053 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63997571 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2191 bytes_read=53085 bytes_retransmit=9 bytes_invalid=0 send_seq=316 receive_seq=316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999482 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2785 bytes_read=8173 bytes_retransmit=9 bytes_invalid=0 send_seq=311 receive_seq=311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.1 EBB42_Gen2_v1.0_T1: temp=27.2 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45861 bytes_read=289328 bytes_retransmit=0 bytes_invalid=0 send_seq=3948 receive_seq=3948 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31998637 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=39.4 th1: temp=39.0 th2: temp=41.7 th3: temp=40.1 sysload=0.32 cputime=29.392 memavail=7390776 print_time=240.376 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 229.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=192158 bytes_read=182063 bytes_retransmit=9 bytes_invalid=0 send_seq=10660 receive_seq=10660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015362 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=2038 bytes_read=8319 bytes_retransmit=0 bytes_invalid=0 send_seq=311 receive_seq=311 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997666 adj=49994992 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9540 bytes_read=37347 bytes_retransmit=9 bytes_invalid=0 send_seq=922 receive_seq=922 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997708 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11130 bytes_read=39859 bytes_retransmit=9 bytes_invalid=0 send_seq=1054 receive_seq=1054 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999990 adj=63997579 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2197 bytes_read=53379 bytes_retransmit=9 bytes_invalid=0 send_seq=317 receive_seq=317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999482 adj=47997679 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2791 bytes_read=8189 bytes_retransmit=9 bytes_invalid=0 send_seq=312 receive_seq=312 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.2 EBB42_Gen2_v1.0_T1: temp=27.2 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45867 bytes_read=289673 bytes_retransmit=0 bytes_invalid=0 send_seq=3949 receive_seq=3949 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31998631 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=39.2 th1: temp=39.2 th2: temp=41.5 th3: temp=39.9 sysload=0.32 cputime=29.435 memavail=7390776 print_time=240.376 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 230.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=192462 bytes_read=182519 bytes_retransmit=9 bytes_invalid=0 send_seq=10684 receive_seq=10684 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015360 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=2050 bytes_read=8351 bytes_retransmit=0 bytes_invalid=0 send_seq=313 receive_seq=313 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997653 adj=49995060 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9552 bytes_read=37491 bytes_retransmit=9 bytes_invalid=0 send_seq=924 receive_seq=924 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997740 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11142 bytes_read=40003 bytes_retransmit=9 bytes_invalid=0 send_seq=1056 receive_seq=1056 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999990 adj=63997585 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2209 bytes_read=53629 bytes_retransmit=9 bytes_invalid=0 send_seq=319 receive_seq=319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999483 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2803 bytes_read=8221 bytes_retransmit=9 bytes_invalid=0 send_seq=314 receive_seq=314 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=28.1 EBB42_Gen2_v1.0_T1: temp=27.5 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45879 bytes_read=290033 bytes_retransmit=0 bytes_invalid=0 send_seq=3951 receive_seq=3951 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31998661 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=39.2 th1: temp=39.7 th2: temp=41.7 th3: temp=39.8 sysload=0.32 cputime=29.478 memavail=7390776 print_time=240.376 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 231.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=192755 bytes_read=182968 bytes_retransmit=9 bytes_invalid=0 send_seq=10706 receive_seq=10706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015353 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=2056 bytes_read=8367 bytes_retransmit=0 bytes_invalid=0 send_seq=314 receive_seq=314 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997648 adj=49995042 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9558 bytes_read=37591 bytes_retransmit=9 bytes_invalid=0 send_seq=925 receive_seq=925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997748 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11148 bytes_read=40103 bytes_retransmit=9 bytes_invalid=0 send_seq=1057 receive_seq=1057 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999990 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2215 bytes_read=53863 bytes_retransmit=9 bytes_invalid=0 send_seq=320 receive_seq=320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999483 adj=47997679 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2809 bytes_read=8237 bytes_retransmit=9 bytes_invalid=0 send_seq=315 receive_seq=315 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.1 EBB42_Gen2_v1.0_T1: temp=27.3 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45885 bytes_read=290378 bytes_retransmit=0 bytes_invalid=0 send_seq=3952 receive_seq=3952 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999870 adj=31998619 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=39.2 th1: temp=39.7 th2: temp=41.5 th3: temp=39.7 sysload=0.30 cputime=29.519 memavail=7390776 print_time=240.376 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 232.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=193043 bytes_read=183383 bytes_retransmit=9 bytes_invalid=0 send_seq=10727 receive_seq=10727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015351 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2062 bytes_read=8396 bytes_retransmit=0 bytes_invalid=0 send_seq=315 receive_seq=315 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997643 adj=49995141 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9564 bytes_read=37705 bytes_retransmit=9 bytes_invalid=0 send_seq=926 receive_seq=926 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000181 adj=63997748 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11154 bytes_read=40217 bytes_retransmit=9 bytes_invalid=0 send_seq=1058 receive_seq=1058 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63997585 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2221 bytes_read=54157 bytes_retransmit=9 bytes_invalid=0 send_seq=321 receive_seq=321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999483 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2815 bytes_read=8264 bytes_retransmit=9 bytes_invalid=0 send_seq=316 receive_seq=316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999898 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.1 EBB42_Gen2_v1.0_T1: temp=27.2 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45891 bytes_read=290723 bytes_retransmit=0 bytes_invalid=0 send_seq=3953 receive_seq=3953 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999870 adj=31998619 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=39.9 th1: temp=39.6 th2: temp=41.8 th3: temp=39.9 sysload=0.30 cputime=29.562 memavail=7390808 print_time=240.376 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 233.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=214631 bytes_read=185483 bytes_retransmit=9 bytes_invalid=0 send_seq=11085 receive_seq=11085 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=4806 freq=400015358 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2068 bytes_read=8412 bytes_retransmit=0 bytes_invalid=0 send_seq=316 receive_seq=316 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997638 adj=49995220 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9570 bytes_read=37819 bytes_retransmit=9 bytes_invalid=0 send_seq=927 receive_seq=927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997798 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11160 bytes_read=40331 bytes_retransmit=9 bytes_invalid=0 send_seq=1059 receive_seq=1059 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63997567 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2227 bytes_read=54406 bytes_retransmit=9 bytes_invalid=0 send_seq=322 receive_seq=322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999483 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2821 bytes_read=8280 bytes_retransmit=9 bytes_invalid=0 send_seq=317 receive_seq=317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999899 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.1 EBB42_Gen2_v1.0_T1: temp=27.6 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45897 bytes_read=291068 bytes_retransmit=0 bytes_invalid=0 send_seq=3954 receive_seq=3954 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999869 adj=31998623 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=39.8 th1: temp=39.7 th2: temp=41.7 th3: temp=39.8 sysload=0.30 cputime=29.664 memavail=7390808 print_time=256.065 buffer_time=0.575 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 234.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=239442 bytes_read=187857 bytes_retransmit=9 bytes_invalid=0 send_seq=11492 receive_seq=11492 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=6662 freq=400015352 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2074 bytes_read=8428 bytes_retransmit=0 bytes_invalid=0 send_seq=317 receive_seq=317 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997637 adj=49995339 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9576 bytes_read=37919 bytes_retransmit=9 bytes_invalid=0 send_seq=928 receive_seq=928 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997741 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11166 bytes_read=40431 bytes_retransmit=9 bytes_invalid=0 send_seq=1060 receive_seq=1060 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63997533 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2233 bytes_read=54640 bytes_retransmit=9 bytes_invalid=0 send_seq=323 receive_seq=323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999485 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2827 bytes_read=8296 bytes_retransmit=9 bytes_invalid=0 send_seq=318 receive_seq=318 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999899 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.3 EBB42_Gen2_v1.0_T1: temp=27.5 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45903 bytes_read=291419 bytes_retransmit=0 bytes_invalid=0 send_seq=3955 receive_seq=3955 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999869 adj=31998611 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=39.9 th1: temp=39.8 th2: temp=41.3 th3: temp=39.8 sysload=0.30 cputime=29.787 memavail=7391804 print_time=257.141 buffer_time=0.651 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 235.1: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=264231 bytes_read=190211 bytes_retransmit=9 bytes_invalid=0 send_seq=11898 receive_seq=11898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=8518 freq=400015343 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2080 bytes_read=8444 bytes_retransmit=0 bytes_invalid=0 send_seq=318 receive_seq=318 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997636 adj=49995424 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9582 bytes_read=38047 bytes_retransmit=9 bytes_invalid=0 send_seq=929 receive_seq=929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63998290 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11172 bytes_read=40559 bytes_retransmit=9 bytes_invalid=0 send_seq=1061 receive_seq=1061 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2239 bytes_read=54934 bytes_retransmit=9 bytes_invalid=0 send_seq=324 receive_seq=324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999485 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2833 bytes_read=8312 bytes_retransmit=9 bytes_invalid=0 send_seq=319 receive_seq=319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999900 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.1 EBB42_Gen2_v1.0_T1: temp=27.4 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45909 bytes_read=291775 bytes_retransmit=0 bytes_invalid=0 send_seq=3956 receive_seq=3956 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31998613 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=40.0 th1: temp=39.6 th2: temp=41.4 th3: temp=39.8 sysload=0.30 cputime=29.901 memavail=7390452 print_time=258.218 buffer_time=0.728 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
webhooks client 3916698168: New connection
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t0' measurements
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 236.1: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=289008 bytes_read=192554 bytes_retransmit=9 bytes_invalid=0 send_seq=12305 receive_seq=12305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=10374 freq=400015348 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2086 bytes_read=8460 bytes_retransmit=0 bytes_invalid=0 send_seq=319 receive_seq=319 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997636 adj=49995504 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9744 bytes_read=40606 bytes_retransmit=9 bytes_invalid=0 send_seq=948 receive_seq=948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63998122 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11178 bytes_read=40673 bytes_retransmit=9 bytes_invalid=0 send_seq=1062 receive_seq=1062 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999988 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2245 bytes_read=55168 bytes_retransmit=9 bytes_invalid=0 send_seq=325 receive_seq=325 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999486 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2839 bytes_read=8328 bytes_retransmit=9 bytes_invalid=0 send_seq=320 receive_seq=320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999900 adj=11999471 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=28.2 EBB42_Gen2_v1.0_T1: temp=27.5 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45915 bytes_read=292131 bytes_retransmit=0 bytes_invalid=0 send_seq=3957 receive_seq=3957 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31998694 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=39.5 th1: temp=39.7 th2: temp=41.4 th3: temp=39.8 sysload=0.27 cputime=30.045 memavail=7390460 print_time=259.294 buffer_time=0.803 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 237.1: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=313758 bytes_read=194908 bytes_retransmit=9 bytes_invalid=0 send_seq=12708 receive_seq=12708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=12223 freq=400015369 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2092 bytes_read=8489 bytes_retransmit=0 bytes_invalid=0 send_seq=320 receive_seq=320 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997637 adj=49995563 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9820 bytes_read=43605 bytes_retransmit=9 bytes_invalid=0 send_seq=959 receive_seq=959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997965 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11184 bytes_read=40773 bytes_retransmit=9 bytes_invalid=0 send_seq=1063 receive_seq=1063 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63997537 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2251 bytes_read=55402 bytes_retransmit=9 bytes_invalid=0 send_seq=326 receive_seq=326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999486 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2845 bytes_read=8355 bytes_retransmit=9 bytes_invalid=0 send_seq=321 receive_seq=321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999900 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.3 EBB42_Gen2_v1.0_T1: temp=27.5 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45921 bytes_read=292487 bytes_retransmit=0 bytes_invalid=0 send_seq=3958 receive_seq=3958 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999875 adj=31998677 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=40.4 th1: temp=39.7 th2: temp=41.4 th3: temp=39.6 sysload=0.27 cputime=30.184 memavail=7390460 print_time=260.371 buffer_time=0.879 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 238.1: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=338621 bytes_read=197258 bytes_retransmit=9 bytes_invalid=0 send_seq=13116 receive_seq=13116 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=14073 freq=400015379 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2098 bytes_read=8505 bytes_retransmit=0 bytes_invalid=0 send_seq=321 receive_seq=321 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997638 adj=49995574 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9896 bytes_read=46663 bytes_retransmit=9 bytes_invalid=0 send_seq=970 receive_seq=970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997811 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11190 bytes_read=40887 bytes_retransmit=9 bytes_invalid=0 send_seq=1064 receive_seq=1064 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63997494 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2257 bytes_read=55711 bytes_retransmit=9 bytes_invalid=0 send_seq=327 receive_seq=327 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999485 adj=47997634 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2851 bytes_read=8371 bytes_retransmit=9 bytes_invalid=0 send_seq=322 receive_seq=322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999900 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=28.1 EBB42_Gen2_v1.0_T1: temp=27.5 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45927 bytes_read=292843 bytes_retransmit=0 bytes_invalid=0 send_seq=3959 receive_seq=3959 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31998674 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=40.2 th1: temp=39.7 th2: temp=41.6 th3: temp=39.9 sysload=0.27 cputime=30.323 memavail=7390464 print_time=261.447 buffer_time=0.955 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.5 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 239.1: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=363405 bytes_read=199593 bytes_retransmit=9 bytes_invalid=0 send_seq=13521 receive_seq=13521 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=15929 freq=400015390 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2104 bytes_read=8521 bytes_retransmit=0 bytes_invalid=0 send_seq=322 receive_seq=322 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997640 adj=49995615 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=9972 bytes_read=49734 bytes_retransmit=9 bytes_invalid=0 send_seq=981 receive_seq=981 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997724 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11196 bytes_read=41001 bytes_retransmit=9 bytes_invalid=0 send_seq=1065 receive_seq=1065 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63997470 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2263 bytes_read=55945 bytes_retransmit=9 bytes_invalid=0 send_seq=328 receive_seq=328 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999485 adj=47997612 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2857 bytes_read=8387 bytes_retransmit=9 bytes_invalid=0 send_seq=323 receive_seq=323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999900 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.4 EBB42_Gen2_v1.0_T1: temp=27.3 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45933 bytes_read=293199 bytes_retransmit=0 bytes_invalid=0 send_seq=3960 receive_seq=3960 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31998636 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=40.4 th1: temp=40.1 th2: temp=41.5 th3: temp=39.8 sysload=0.27 cputime=30.463 memavail=7390464 print_time=262.524 buffer_time=1.031 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 240.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=389184 bytes_read=202058 bytes_retransmit=9 bytes_invalid=0 send_seq=13943 receive_seq=13943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=16827 freq=400015405 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2110 bytes_read=8537 bytes_retransmit=0 bytes_invalid=0 send_seq=323 receive_seq=323 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997643 adj=49995646 toolboard_t0: mcu_awake=0.300 mcu_task_avg=0.000117 mcu_task_stddev=0.000069 bytes_write=10048 bytes_read=52809 bytes_retransmit=9 bytes_invalid=0 send_seq=992 receive_seq=992 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997665 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11202 bytes_read=41115 bytes_retransmit=9 bytes_invalid=0 send_seq=1066 receive_seq=1066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999988 adj=63997461 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2269 bytes_read=56179 bytes_retransmit=9 bytes_invalid=0 send_seq=329 receive_seq=329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999486 adj=47997598 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2863 bytes_read=8403 bytes_retransmit=9 bytes_invalid=0 send_seq=324 receive_seq=324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999900 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.2 EBB42_Gen2_v1.0_T1: temp=27.4 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45939 bytes_read=293555 bytes_retransmit=0 bytes_invalid=0 send_seq=3961 receive_seq=3961 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31998609 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=40.5 th1: temp=39.6 th2: temp=41.3 th3: temp=39.6 sysload=0.27 cputime=30.604 memavail=7390464 print_time=263.600 buffer_time=1.107 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 241.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=413978 bytes_read=204403 bytes_retransmit=9 bytes_invalid=0 send_seq=14350 receive_seq=14350 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=18713 freq=400015410 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2116 bytes_read=8553 bytes_retransmit=0 bytes_invalid=0 send_seq=324 receive_seq=324 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997647 adj=49995688 toolboard_t0: mcu_awake=0.300 mcu_task_avg=0.000117 mcu_task_stddev=0.000069 bytes_write=10124 bytes_read=55937 bytes_retransmit=9 bytes_invalid=0 send_seq=1003 receive_seq=1003 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997618 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11208 bytes_read=41229 bytes_retransmit=9 bytes_invalid=0 send_seq=1067 receive_seq=1067 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999988 adj=63997435 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2275 bytes_read=56473 bytes_retransmit=9 bytes_invalid=0 send_seq=330 receive_seq=330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999487 adj=47997596 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2869 bytes_read=8419 bytes_retransmit=9 bytes_invalid=0 send_seq=325 receive_seq=325 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999423 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=28.2 EBB42_Gen2_v1.0_T1: temp=27.4 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45945 bytes_read=293911 bytes_retransmit=0 bytes_invalid=0 send_seq=3962 receive_seq=3962 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31998598 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=40.7 th1: temp=39.9 th2: temp=41.3 th3: temp=39.7 sysload=0.25 cputime=30.743 memavail=7390484 print_time=264.677 buffer_time=1.183 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 242.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=438775 bytes_read=206733 bytes_retransmit=9 bytes_invalid=0 send_seq=14754 receive_seq=14754 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=20539 freq=400015481 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2122 bytes_read=8582 bytes_retransmit=0 bytes_invalid=0 send_seq=325 receive_seq=325 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997653 adj=49995752 toolboard_t0: mcu_awake=0.300 mcu_task_avg=0.000117 mcu_task_stddev=0.000069 bytes_write=10200 bytes_read=59008 bytes_retransmit=9 bytes_invalid=0 send_seq=1014 receive_seq=1014 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997637 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11214 bytes_read=41343 bytes_retransmit=9 bytes_invalid=0 send_seq=1068 receive_seq=1068 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999988 adj=63997442 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2281 bytes_read=56707 bytes_retransmit=9 bytes_invalid=0 send_seq=331 receive_seq=331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999487 adj=47997605 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2875 bytes_read=8446 bytes_retransmit=9 bytes_invalid=0 send_seq=326 receive_seq=326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.4 EBB42_Gen2_v1.0_T1: temp=27.4 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45951 bytes_read=294267 bytes_retransmit=0 bytes_invalid=0 send_seq=3963 receive_seq=3963 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31998589 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=40.5 th1: temp=39.3 th2: temp=41.6 th3: temp=39.6 sysload=0.25 cputime=30.883 memavail=7390484 print_time=265.753 buffer_time=1.259 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 243.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=463546 bytes_read=209102 bytes_retransmit=9 bytes_invalid=0 send_seq=15160 receive_seq=15160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=22395 freq=400015687 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2128 bytes_read=8598 bytes_retransmit=0 bytes_invalid=0 send_seq=326 receive_seq=326 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997660 adj=49995694 toolboard_t0: mcu_awake=0.300 mcu_task_avg=0.000117 mcu_task_stddev=0.000069 bytes_write=10276 bytes_read=62066 bytes_retransmit=9 bytes_invalid=0 send_seq=1025 receive_seq=1025 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997464 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11220 bytes_read=41443 bytes_retransmit=9 bytes_invalid=0 send_seq=1069 receive_seq=1069 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999988 adj=63997285 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2287 bytes_read=56956 bytes_retransmit=9 bytes_invalid=0 send_seq=332 receive_seq=332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999488 adj=47997484 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2881 bytes_read=8462 bytes_retransmit=9 bytes_invalid=0 send_seq=327 receive_seq=327 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999408 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.2 EBB42_Gen2_v1.0_T1: temp=27.5 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45957 bytes_read=294623 bytes_retransmit=0 bytes_invalid=0 send_seq=3964 receive_seq=3964 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31998537 coil_temp=17.6 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=40.5 th1: temp=39.9 th2: temp=41.2 th3: temp=39.7 sysload=0.25 cputime=31.024 memavail=7390484 print_time=266.829 buffer_time=1.334 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 244.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=488307 bytes_read=211442 bytes_retransmit=9 bytes_invalid=0 send_seq=15566 receive_seq=15566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=24279 freq=400015659 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2134 bytes_read=8614 bytes_retransmit=0 bytes_invalid=0 send_seq=327 receive_seq=327 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997666 adj=49995396 toolboard_t0: mcu_awake=0.300 mcu_task_avg=0.000117 mcu_task_stddev=0.000069 bytes_write=10352 bytes_read=65154 bytes_retransmit=9 bytes_invalid=0 send_seq=1036 receive_seq=1036 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63996981 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11226 bytes_read=41571 bytes_retransmit=9 bytes_invalid=0 send_seq=1070 receive_seq=1070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63996827 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2293 bytes_read=57246 bytes_retransmit=9 bytes_invalid=0 send_seq=333 receive_seq=333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999489 adj=47997148 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2887 bytes_read=8478 bytes_retransmit=9 bytes_invalid=0 send_seq=328 receive_seq=328 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999320 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.3 EBB42_Gen2_v1.0_T1: temp=27.6 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45963 bytes_read=294979 bytes_retransmit=0 bytes_invalid=0 send_seq=3965 receive_seq=3965 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31998295 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=41.0 th1: temp=40.2 th2: temp=41.5 th3: temp=39.6 sysload=0.25 cputime=31.163 memavail=7390232 print_time=267.906 buffer_time=1.411 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 245.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=513163 bytes_read=213798 bytes_retransmit=9 bytes_invalid=0 send_seq=15972 receive_seq=15972 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=26092 freq=400015633 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2140 bytes_read=8630 bytes_retransmit=0 bytes_invalid=0 send_seq=328 receive_seq=328 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997674 adj=49995634 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=10428 bytes_read=68215 bytes_retransmit=9 bytes_invalid=0 send_seq=1047 receive_seq=1047 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997211 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11232 bytes_read=41678 bytes_retransmit=9 bytes_invalid=0 send_seq=1071 receive_seq=1071 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999988 adj=63997078 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2299 bytes_read=57464 bytes_retransmit=9 bytes_invalid=0 send_seq=334 receive_seq=334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999489 adj=47997339 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2893 bytes_read=8494 bytes_retransmit=9 bytes_invalid=0 send_seq=329 receive_seq=329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999360 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.2 EBB42_Gen2_v1.0_T1: temp=27.4 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45969 bytes_read=295335 bytes_retransmit=0 bytes_invalid=0 send_seq=3966 receive_seq=3966 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31998415 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=41.4 th1: temp=40.0 th2: temp=41.4 th3: temp=39.6 sysload=0.25 cputime=31.305 memavail=7388520 print_time=268.982 buffer_time=1.486 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 246.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=537916 bytes_read=216143 bytes_retransmit=9 bytes_invalid=0 send_seq=16374 receive_seq=16374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=27948 freq=400015650 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2146 bytes_read=8646 bytes_retransmit=0 bytes_invalid=0 send_seq=329 receive_seq=329 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997681 adj=49995829 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=10504 bytes_read=71254 bytes_retransmit=9 bytes_invalid=0 send_seq=1058 receive_seq=1058 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997373 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11238 bytes_read=41771 bytes_retransmit=9 bytes_invalid=0 send_seq=1072 receive_seq=1072 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999988 adj=63997244 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2305 bytes_read=57682 bytes_retransmit=9 bytes_invalid=0 send_seq=335 receive_seq=335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999488 adj=47997457 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2899 bytes_read=8510 bytes_retransmit=9 bytes_invalid=0 send_seq=330 receive_seq=330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999389 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=28.3 EBB42_Gen2_v1.0_T1: temp=27.3 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45975 bytes_read=295691 bytes_retransmit=0 bytes_invalid=0 send_seq=3967 receive_seq=3967 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31998498 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=40.9 th1: temp=40.0 th2: temp=41.2 th3: temp=39.4 sysload=0.23 cputime=31.451 memavail=7388524 print_time=270.059 buffer_time=1.562 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 247.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=563675 bytes_read=218568 bytes_retransmit=9 bytes_invalid=0 send_seq=16797 receive_seq=16797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=28908 freq=400015644 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2152 bytes_read=8675 bytes_retransmit=0 bytes_invalid=0 send_seq=330 receive_seq=330 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997687 adj=49995874 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=10580 bytes_read=74320 bytes_retransmit=9 bytes_invalid=0 send_seq=1069 receive_seq=1069 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997395 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11244 bytes_read=41890 bytes_retransmit=9 bytes_invalid=0 send_seq=1073 receive_seq=1073 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999988 adj=63997262 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2311 bytes_read=57956 bytes_retransmit=9 bytes_invalid=0 send_seq=336 receive_seq=336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999492 adj=47997463 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2905 bytes_read=8537 bytes_retransmit=9 bytes_invalid=0 send_seq=331 receive_seq=331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999390 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.3 EBB42_Gen2_v1.0_T1: temp=27.6 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45981 bytes_read=296047 bytes_retransmit=0 bytes_invalid=0 send_seq=3968 receive_seq=3968 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31998512 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=41.0 th1: temp=40.1 th2: temp=41.3 th3: temp=39.6 sysload=0.23 cputime=31.601 memavail=7388288 print_time=271.135 buffer_time=1.638 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 248.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=588543 bytes_read=220928 bytes_retransmit=9 bytes_invalid=0 send_seq=17207 receive_seq=17207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=30732 freq=400015641 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2158 bytes_read=8691 bytes_retransmit=0 bytes_invalid=0 send_seq=331 receive_seq=331 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997695 adj=49995942 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=10656 bytes_read=77417 bytes_retransmit=9 bytes_invalid=0 send_seq=1080 receive_seq=1080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997488 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11250 bytes_read=41983 bytes_retransmit=9 bytes_invalid=0 send_seq=1074 receive_seq=1074 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999988 adj=63997339 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2317 bytes_read=58189 bytes_retransmit=9 bytes_invalid=0 send_seq=337 receive_seq=337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999491 adj=47997566 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2911 bytes_read=8553 bytes_retransmit=9 bytes_invalid=0 send_seq=332 receive_seq=332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999900 adj=11999404 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=28.3 EBB42_Gen2_v1.0_T1: temp=27.4 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45987 bytes_read=296403 bytes_retransmit=0 bytes_invalid=0 send_seq=3969 receive_seq=3969 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31998545 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=41.0 th1: temp=40.1 th2: temp=41.3 th3: temp=39.6 sysload=0.23 cputime=31.750 memavail=7388044 print_time=272.212 buffer_time=1.714 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 249.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=613316 bytes_read=223297 bytes_retransmit=9 bytes_invalid=0 send_seq=17613 receive_seq=17613 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=32588 freq=400015626 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2164 bytes_read=8707 bytes_retransmit=0 bytes_invalid=0 send_seq=332 receive_seq=332 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997704 adj=49996008 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=10732 bytes_read=80465 bytes_retransmit=9 bytes_invalid=0 send_seq=1091 receive_seq=1091 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997543 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11256 bytes_read=42080 bytes_retransmit=9 bytes_invalid=0 send_seq=1075 receive_seq=1075 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999990 adj=63997399 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2323 bytes_read=58407 bytes_retransmit=9 bytes_invalid=0 send_seq=338 receive_seq=338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999491 adj=47997580 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2917 bytes_read=8569 bytes_retransmit=9 bytes_invalid=0 send_seq=333 receive_seq=333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999900 adj=11999411 Octopus_Pro_H723_V1.1: temp=28.2 EBB42_Gen2_v1.0_T0: temp=28.3 EBB42_Gen2_v1.0_T1: temp=27.6 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45993 bytes_read=296759 bytes_retransmit=0 bytes_invalid=0 send_seq=3970 receive_seq=3970 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31998564 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=41.0 th1: temp=40.0 th2: temp=41.3 th3: temp=39.8 sysload=0.23 cputime=31.892 memavail=7388048 print_time=273.288 buffer_time=1.789 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 250.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=638090 bytes_read=225638 bytes_retransmit=9 bytes_invalid=0 send_seq=18016 receive_seq=18016 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=34444 freq=400015615 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2170 bytes_read=8723 bytes_retransmit=0 bytes_invalid=0 send_seq=333 receive_seq=333 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997713 adj=49996084 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000068 bytes_write=10801 bytes_read=83544 bytes_retransmit=9 bytes_invalid=0 send_seq=1101 receive_seq=1101 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997754 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=11262 bytes_read=42222 bytes_retransmit=9 bytes_invalid=0 send_seq=1076 receive_seq=1076 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63997477 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2329 bytes_read=58689 bytes_retransmit=9 bytes_invalid=0 send_seq=339 receive_seq=339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999491 adj=47997614 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2923 bytes_read=8585 bytes_retransmit=9 bytes_invalid=0 send_seq=334 receive_seq=334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999900 adj=11999421 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=28.3 EBB42_Gen2_v1.0_T1: temp=27.6 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=45999 bytes_read=297115 bytes_retransmit=0 bytes_invalid=0 send_seq=3971 receive_seq=3971 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31998587 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.011 th0: temp=41.1 th1: temp=40.1 th2: temp=41.4 th3: temp=39.6 sysload=0.23 cputime=32.030 memavail=7388048 print_time=274.365 buffer_time=1.866 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 251.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=662893 bytes_read=227968 bytes_retransmit=9 bytes_invalid=0 send_seq=18420 receive_seq=18420 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=36265 freq=400015593 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2176 bytes_read=8739 bytes_retransmit=0 bytes_invalid=0 send_seq=334 receive_seq=334 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997730 adj=49996143 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000068 bytes_write=10877 bytes_read=86602 bytes_retransmit=9 bytes_invalid=0 send_seq=1112 receive_seq=1112 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997790 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=11268 bytes_read=42322 bytes_retransmit=9 bytes_invalid=0 send_seq=1077 receive_seq=1077 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63997495 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2335 bytes_read=58923 bytes_retransmit=9 bytes_invalid=0 send_seq=340 receive_seq=340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999494 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2929 bytes_read=8601 bytes_retransmit=9 bytes_invalid=0 send_seq=335 receive_seq=335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999900 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.1 EBB42_Gen2_v1.0_T1: temp=27.6 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46005 bytes_read=297471 bytes_retransmit=0 bytes_invalid=0 send_seq=3972 receive_seq=3972 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31998607 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=41.2 th1: temp=40.0 th2: temp=41.4 th3: temp=39.7 sysload=0.21 cputime=32.180 memavail=7382024 print_time=275.441 buffer_time=1.941 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 252.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=687769 bytes_read=230352 bytes_retransmit=9 bytes_invalid=0 send_seq=18829 receive_seq=18829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=38076 freq=400015569 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2182 bytes_read=8768 bytes_retransmit=0 bytes_invalid=0 send_seq=335 receive_seq=335 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997742 adj=49996308 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000068 bytes_write=10953 bytes_read=89658 bytes_retransmit=9 bytes_invalid=0 send_seq=1123 receive_seq=1123 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997846 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=11274 bytes_read=42422 bytes_retransmit=9 bytes_invalid=0 send_seq=1078 receive_seq=1078 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63997535 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2341 bytes_read=59157 bytes_retransmit=9 bytes_invalid=0 send_seq=341 receive_seq=341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999493 adj=47997698 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2935 bytes_read=8628 bytes_retransmit=9 bytes_invalid=0 send_seq=336 receive_seq=336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999900 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.4 EBB42_Gen2_v1.0_T1: temp=27.6 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46011 bytes_read=297827 bytes_retransmit=0 bytes_invalid=0 send_seq=3973 receive_seq=3973 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31998638 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=41.3 th1: temp=39.9 th2: temp=41.5 th3: temp=39.8 sysload=0.21 cputime=32.323 memavail=7388156 print_time=276.518 buffer_time=2.015 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 253.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=712532 bytes_read=232682 bytes_retransmit=9 bytes_invalid=0 send_seq=19233 receive_seq=19233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=27716 freq=400015547 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2188 bytes_read=8784 bytes_retransmit=0 bytes_invalid=0 send_seq=336 receive_seq=336 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997753 adj=49996362 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000068 bytes_write=11029 bytes_read=92743 bytes_retransmit=9 bytes_invalid=0 send_seq=1134 receive_seq=1134 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997829 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=11280 bytes_read=42550 bytes_retransmit=9 bytes_invalid=0 send_seq=1079 receive_seq=1079 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63997574 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2347 bytes_read=59466 bytes_retransmit=9 bytes_invalid=0 send_seq=342 receive_seq=342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999493 adj=47997707 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2941 bytes_read=8644 bytes_retransmit=9 bytes_invalid=0 send_seq=337 receive_seq=337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999900 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.2 EBB42_Gen2_v1.0_T1: temp=27.4 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46017 bytes_read=298183 bytes_retransmit=0 bytes_invalid=0 send_seq=3974 receive_seq=3974 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31998658 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=40.9 th1: temp=40.3 th2: temp=41.3 th3: temp=39.7 sysload=0.21 cputime=32.448 memavail=7387908 print_time=277.056 buffer_time=1.553 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 254.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=738309 bytes_read=235082 bytes_retransmit=9 bytes_invalid=0 send_seq=19651 receive_seq=19651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=28676 freq=400015574 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2194 bytes_read=8800 bytes_retransmit=0 bytes_invalid=0 send_seq=337 receive_seq=337 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997763 adj=49996561 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000068 bytes_write=11105 bytes_read=95801 bytes_retransmit=9 bytes_invalid=0 send_seq=1145 receive_seq=1145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997932 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=11286 bytes_read=42650 bytes_retransmit=9 bytes_invalid=0 send_seq=1080 receive_seq=1080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63997634 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2353 bytes_read=59700 bytes_retransmit=9 bytes_invalid=0 send_seq=343 receive_seq=343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999493 adj=47997752 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2947 bytes_read=8660 bytes_retransmit=9 bytes_invalid=0 send_seq=338 receive_seq=338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999900 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=28.5 EBB42_Gen2_v1.0_T1: temp=27.6 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46023 bytes_read=298539 bytes_retransmit=0 bytes_invalid=0 send_seq=3975 receive_seq=3975 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31998680 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.011 th0: temp=40.8 th1: temp=40.0 th2: temp=41.5 th3: temp=39.7 sysload=0.21 cputime=32.591 memavail=7387660 print_time=278.132 buffer_time=1.629 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 255.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=763045 bytes_read=237457 bytes_retransmit=9 bytes_invalid=0 send_seq=20055 receive_seq=20055 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=30532 freq=400015714 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2200 bytes_read=8816 bytes_retransmit=0 bytes_invalid=0 send_seq=338 receive_seq=338 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997774 adj=49996550 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=11181 bytes_read=98935 bytes_retransmit=9 bytes_invalid=0 send_seq=1156 receive_seq=1156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997791 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=11292 bytes_read=42750 bytes_retransmit=9 bytes_invalid=0 send_seq=1081 receive_seq=1081 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2359 bytes_read=59934 bytes_retransmit=9 bytes_invalid=0 send_seq=344 receive_seq=344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999493 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2953 bytes_read=8676 bytes_retransmit=9 bytes_invalid=0 send_seq=339 receive_seq=339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999900 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=28.4 EBB42_Gen2_v1.0_T1: temp=27.5 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46029 bytes_read=298895 bytes_retransmit=0 bytes_invalid=0 send_seq=3976 receive_seq=3976 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31998646 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=41.3 th1: temp=40.0 th2: temp=41.7 th3: temp=39.7 sysload=0.21 cputime=32.730 memavail=7387204 print_time=279.209 buffer_time=1.705 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 256.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=787819 bytes_read=239782 bytes_retransmit=9 bytes_invalid=0 send_seq=20458 receive_seq=20458 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=32388 freq=400015686 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2206 bytes_read=8832 bytes_retransmit=0 bytes_invalid=0 send_seq=339 receive_seq=339 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997786 adj=49996235 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=11257 bytes_read=102020 bytes_retransmit=9 bytes_invalid=0 send_seq=1167 receive_seq=1167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997390 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11298 bytes_read=42892 bytes_retransmit=9 bytes_invalid=0 send_seq=1082 receive_seq=1082 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63997203 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2365 bytes_read=60228 bytes_retransmit=9 bytes_invalid=0 send_seq=345 receive_seq=345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999494 adj=47997406 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2959 bytes_read=8692 bytes_retransmit=9 bytes_invalid=0 send_seq=340 receive_seq=340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999373 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.3 EBB42_Gen2_v1.0_T1: temp=27.4 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46035 bytes_read=299251 bytes_retransmit=0 bytes_invalid=0 send_seq=3977 receive_seq=3977 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31998470 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.011 th0: temp=41.2 th1: temp=40.3 th2: temp=41.2 th3: temp=39.6 sysload=0.20 cputime=32.873 memavail=7386956 print_time=280.285 buffer_time=1.781 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 257.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=812583 bytes_read=242092 bytes_retransmit=9 bytes_invalid=0 send_seq=20859 receive_seq=20859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=34244 freq=400015674 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2212 bytes_read=8861 bytes_retransmit=0 bytes_invalid=0 send_seq=340 receive_seq=340 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997798 adj=49996336 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=11333 bytes_read=105077 bytes_retransmit=9 bytes_invalid=0 send_seq=1178 receive_seq=1178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997641 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11304 bytes_read=42992 bytes_retransmit=9 bytes_invalid=0 send_seq=1083 receive_seq=1083 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999990 adj=63997339 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2371 bytes_read=60462 bytes_retransmit=9 bytes_invalid=0 send_seq=346 receive_seq=346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999493 adj=47997524 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2965 bytes_read=8719 bytes_retransmit=9 bytes_invalid=0 send_seq=341 receive_seq=341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=28.3 EBB42_Gen2_v1.0_T1: temp=27.6 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46041 bytes_read=299607 bytes_retransmit=0 bytes_invalid=0 send_seq=3978 receive_seq=3978 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31998542 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.011 th0: temp=41.8 th1: temp=40.3 th2: temp=41.4 th3: temp=39.7 sysload=0.20 cputime=33.016 memavail=7386708 print_time=281.362 buffer_time=1.857 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 258.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=837415 bytes_read=244461 bytes_retransmit=9 bytes_invalid=0 send_seq=21265 receive_seq=21265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=36100 freq=400015660 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2218 bytes_read=8877 bytes_retransmit=0 bytes_invalid=0 send_seq=341 receive_seq=341 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997810 adj=49996383 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=11409 bytes_read=108134 bytes_retransmit=9 bytes_invalid=0 send_seq=1189 receive_seq=1189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997648 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11310 bytes_read=43092 bytes_retransmit=9 bytes_invalid=0 send_seq=1084 receive_seq=1084 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999990 adj=63997410 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2377 bytes_read=60711 bytes_retransmit=9 bytes_invalid=0 send_seq=347 receive_seq=347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999493 adj=47997560 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2971 bytes_read=8735 bytes_retransmit=9 bytes_invalid=0 send_seq=342 receive_seq=342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=28.4 EBB42_Gen2_v1.0_T1: temp=27.7 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46047 bytes_read=299963 bytes_retransmit=0 bytes_invalid=0 send_seq=3979 receive_seq=3979 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31998574 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=41.1 th1: temp=40.3 th2: temp=41.5 th3: temp=39.7 sysload=0.20 cputime=33.164 memavail=7386720 print_time=282.438 buffer_time=1.933 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 259.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=862194 bytes_read=246811 bytes_retransmit=9 bytes_invalid=0 send_seq=21673 receive_seq=21673 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=37943 freq=400015639 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2224 bytes_read=8893 bytes_retransmit=0 bytes_invalid=0 send_seq=342 receive_seq=342 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997823 adj=49996427 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=11485 bytes_read=111219 bytes_retransmit=9 bytes_invalid=0 send_seq=1200 receive_seq=1200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997666 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11316 bytes_read=43220 bytes_retransmit=9 bytes_invalid=0 send_seq=1085 receive_seq=1085 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63997465 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2383 bytes_read=61005 bytes_retransmit=9 bytes_invalid=0 send_seq=348 receive_seq=348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999492 adj=47997591 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2977 bytes_read=8751 bytes_retransmit=9 bytes_invalid=0 send_seq=343 receive_seq=343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.4 EBB42_Gen2_v1.0_T1: temp=27.6 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46053 bytes_read=300319 bytes_retransmit=0 bytes_invalid=0 send_seq=3980 receive_seq=3980 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31998599 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=41.2 th1: temp=40.2 th2: temp=41.4 th3: temp=39.7 sysload=0.20 cputime=33.311 memavail=7386724 print_time=283.515 buffer_time=2.009 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 260.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=886978 bytes_read=249162 bytes_retransmit=9 bytes_invalid=0 send_seq=22078 receive_seq=22078 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=39799 freq=400015661 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2230 bytes_read=8909 bytes_retransmit=0 bytes_invalid=0 send_seq=343 receive_seq=343 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997835 adj=49996478 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=11561 bytes_read=114293 bytes_retransmit=9 bytes_invalid=0 send_seq=1211 receive_seq=1211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997686 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11322 bytes_read=43320 bytes_retransmit=9 bytes_invalid=0 send_seq=1086 receive_seq=1086 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999990 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2389 bytes_read=61239 bytes_retransmit=9 bytes_invalid=0 send_seq=349 receive_seq=349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999492 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2983 bytes_read=8767 bytes_retransmit=9 bytes_invalid=0 send_seq=344 receive_seq=344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.2 EBB42_Gen2_v1.0_T1: temp=27.7 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46059 bytes_read=300675 bytes_retransmit=0 bytes_invalid=0 send_seq=3981 receive_seq=3981 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31998627 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=41.3 th1: temp=40.2 th2: temp=41.2 th3: temp=39.5 sysload=0.20 cputime=33.452 memavail=7386724 print_time=284.591 buffer_time=2.085 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 261.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=912775 bytes_read=251611 bytes_retransmit=9 bytes_invalid=0 send_seq=22500 receive_seq=22500 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=40758 freq=400015681 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2236 bytes_read=8925 bytes_retransmit=0 bytes_invalid=0 send_seq=344 receive_seq=344 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997848 adj=49996454 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=11637 bytes_read=117351 bytes_retransmit=9 bytes_invalid=0 send_seq=1222 receive_seq=1222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997714 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11328 bytes_read=43434 bytes_retransmit=9 bytes_invalid=0 send_seq=1087 receive_seq=1087 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999989 adj=63997464 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2395 bytes_read=61473 bytes_retransmit=9 bytes_invalid=0 send_seq=350 receive_seq=350 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999492 adj=47997586 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2989 bytes_read=8783 bytes_retransmit=9 bytes_invalid=0 send_seq=345 receive_seq=345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.3 EBB42_Gen2_v1.0_T1: temp=27.8 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46065 bytes_read=301031 bytes_retransmit=0 bytes_invalid=0 send_seq=3982 receive_seq=3982 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31998619 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=41.8 th1: temp=40.2 th2: temp=41.7 th3: temp=39.7 sysload=0.18 cputime=33.596 memavail=7386728 print_time=285.668 buffer_time=2.161 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 262.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=937569 bytes_read=253956 bytes_retransmit=9 bytes_invalid=0 send_seq=22907 receive_seq=22907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=42583 freq=400015707 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2242 bytes_read=8954 bytes_retransmit=0 bytes_invalid=0 send_seq=345 receive_seq=345 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997861 adj=49996450 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=11706 bytes_read=120412 bytes_retransmit=9 bytes_invalid=0 send_seq=1232 receive_seq=1232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997659 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11334 bytes_read=43562 bytes_retransmit=9 bytes_invalid=0 send_seq=1088 receive_seq=1088 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999990 adj=63997425 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2401 bytes_read=61767 bytes_retransmit=9 bytes_invalid=0 send_seq=351 receive_seq=351 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999492 adj=47997566 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2995 bytes_read=8810 bytes_retransmit=9 bytes_invalid=0 send_seq=346 receive_seq=346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.4 EBB42_Gen2_v1.0_T1: temp=27.8 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46071 bytes_read=301387 bytes_retransmit=0 bytes_invalid=0 send_seq=3983 receive_seq=3983 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31998592 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=41.6 th1: temp=40.5 th2: temp=41.5 th3: temp=39.9 sysload=0.18 cputime=33.737 memavail=7386732 print_time=286.744 buffer_time=2.237 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 263.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=962363 bytes_read=256301 bytes_retransmit=9 bytes_invalid=0 send_seq=23314 receive_seq=23314 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=44439 freq=400015756 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2248 bytes_read=8970 bytes_retransmit=0 bytes_invalid=0 send_seq=346 receive_seq=346 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997874 adj=49996438 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=11782 bytes_read=123530 bytes_retransmit=9 bytes_invalid=0 send_seq=1243 receive_seq=1243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997585 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11340 bytes_read=43662 bytes_retransmit=9 bytes_invalid=0 send_seq=1089 receive_seq=1089 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999990 adj=63997392 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2407 bytes_read=62016 bytes_retransmit=9 bytes_invalid=0 send_seq=352 receive_seq=352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999492 adj=47997535 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3001 bytes_read=8826 bytes_retransmit=9 bytes_invalid=0 send_seq=347 receive_seq=347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999416 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.5 EBB42_Gen2_v1.0_T1: temp=27.7 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46077 bytes_read=301743 bytes_retransmit=0 bytes_invalid=0 send_seq=3984 receive_seq=3984 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999871 adj=31998572 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=41.4 th1: temp=40.4 th2: temp=41.5 th3: temp=40.0 sysload=0.18 cputime=33.882 memavail=7386740 print_time=287.821 buffer_time=2.313 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 264.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=987224 bytes_read=258685 bytes_retransmit=9 bytes_invalid=0 send_seq=23723 receive_seq=23723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=46261 freq=400015732 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2254 bytes_read=8986 bytes_retransmit=0 bytes_invalid=0 send_seq=347 receive_seq=347 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997888 adj=49996401 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=11858 bytes_read=126589 bytes_retransmit=9 bytes_invalid=0 send_seq=1254 receive_seq=1254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997487 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11346 bytes_read=43762 bytes_retransmit=9 bytes_invalid=0 send_seq=1090 receive_seq=1090 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999992 adj=63997323 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2413 bytes_read=62250 bytes_retransmit=9 bytes_invalid=0 send_seq=353 receive_seq=353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999492 adj=47997481 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3007 bytes_read=8842 bytes_retransmit=9 bytes_invalid=0 send_seq=348 receive_seq=348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999400 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.3 EBB42_Gen2_v1.0_T1: temp=27.6 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46083 bytes_read=302099 bytes_retransmit=0 bytes_invalid=0 send_seq=3985 receive_seq=3985 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999870 adj=31998529 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=41.1 th1: temp=40.4 th2: temp=41.6 th3: temp=39.7 sysload=0.18 cputime=34.052 memavail=7405396 print_time=288.897 buffer_time=2.388 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 265.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1011956 bytes_read=261041 bytes_retransmit=9 bytes_invalid=0 send_seq=24129 receive_seq=24129 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=48151 freq=400015714 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2260 bytes_read=9002 bytes_retransmit=0 bytes_invalid=0 send_seq=348 receive_seq=348 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997902 adj=49996486 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=11934 bytes_read=129693 bytes_retransmit=9 bytes_invalid=0 send_seq=1265 receive_seq=1265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997645 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11352 bytes_read=43890 bytes_retransmit=9 bytes_invalid=0 send_seq=1091 receive_seq=1091 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999993 adj=63997419 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2419 bytes_read=62544 bytes_retransmit=9 bytes_invalid=0 send_seq=354 receive_seq=354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999493 adj=47997544 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3013 bytes_read=8858 bytes_retransmit=9 bytes_invalid=0 send_seq=349 receive_seq=349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999903 adj=11999412 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.5 EBB42_Gen2_v1.0_T1: temp=27.7 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46089 bytes_read=302455 bytes_retransmit=0 bytes_invalid=0 send_seq=3986 receive_seq=3986 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31998565 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=41.5 th1: temp=40.3 th2: temp=41.5 th3: temp=39.9 sysload=0.18 cputime=34.202 memavail=7404388 print_time=289.974 buffer_time=2.464 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 266.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1036840 bytes_read=263396 bytes_retransmit=9 bytes_invalid=0 send_seq=24538 receive_seq=24538 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=37711 freq=400015691 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2266 bytes_read=9017 bytes_retransmit=0 bytes_invalid=0 send_seq=349 receive_seq=349 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997916 adj=49996545 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=12010 bytes_read=132750 bytes_retransmit=9 bytes_invalid=0 send_seq=1276 receive_seq=1276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997659 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11358 bytes_read=44004 bytes_retransmit=9 bytes_invalid=0 send_seq=1092 receive_seq=1092 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999992 adj=63997470 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2425 bytes_read=62778 bytes_retransmit=9 bytes_invalid=0 send_seq=355 receive_seq=355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999493 adj=47997590 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3019 bytes_read=8874 bytes_retransmit=9 bytes_invalid=0 send_seq=350 receive_seq=350 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999903 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.4 EBB42_Gen2_v1.0_T1: temp=27.6 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46095 bytes_read=302811 bytes_retransmit=0 bytes_invalid=0 send_seq=3987 receive_seq=3987 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31998605 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=41.7 th1: temp=40.4 th2: temp=41.5 th3: temp=39.6 sysload=0.16 cputime=34.334 memavail=7404640 print_time=290.512 buffer_time=2.001 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 267.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1061634 bytes_read=265769 bytes_retransmit=9 bytes_invalid=0 send_seq=24945 receive_seq=24945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=39567 freq=400015669 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2272 bytes_read=9045 bytes_retransmit=0 bytes_invalid=0 send_seq=350 receive_seq=350 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997928 adj=49996735 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=12086 bytes_read=135807 bytes_retransmit=9 bytes_invalid=0 send_seq=1287 receive_seq=1287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997692 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11364 bytes_read=44104 bytes_retransmit=9 bytes_invalid=0 send_seq=1093 receive_seq=1093 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999992 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2431 bytes_read=63012 bytes_retransmit=9 bytes_invalid=0 send_seq=356 receive_seq=356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999493 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3025 bytes_read=8901 bytes_retransmit=9 bytes_invalid=0 send_seq=351 receive_seq=351 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.6 EBB42_Gen2_v1.0_T1: temp=27.8 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46101 bytes_read=303167 bytes_retransmit=0 bytes_invalid=0 send_seq=3988 receive_seq=3988 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999875 adj=31998629 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=41.5 th1: temp=39.8 th2: temp=41.5 th3: temp=39.9 sysload=0.16 cputime=34.482 memavail=7404640 print_time=291.588 buffer_time=2.077 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 268.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1087409 bytes_read=268179 bytes_retransmit=9 bytes_invalid=0 send_seq=25366 receive_seq=25366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=40495 freq=400015659 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2278 bytes_read=9060 bytes_retransmit=0 bytes_invalid=0 send_seq=351 receive_seq=351 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997947 adj=49996832 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=12162 bytes_read=138895 bytes_retransmit=9 bytes_invalid=0 send_seq=1298 receive_seq=1298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997701 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11370 bytes_read=44232 bytes_retransmit=9 bytes_invalid=0 send_seq=1094 receive_seq=1094 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999994 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2437 bytes_read=63321 bytes_retransmit=9 bytes_invalid=0 send_seq=357 receive_seq=357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999497 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3031 bytes_read=8917 bytes_retransmit=9 bytes_invalid=0 send_seq=352 receive_seq=352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=28.6 EBB42_Gen2_v1.0_T1: temp=27.7 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46107 bytes_read=303523 bytes_retransmit=0 bytes_invalid=0 send_seq=3989 receive_seq=3989 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999875 adj=31998686 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=41.6 th1: temp=40.3 th2: temp=41.7 th3: temp=40.3 sysload=0.16 cputime=34.654 memavail=7401880 print_time=292.665 buffer_time=2.153 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 269.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1112138 bytes_read=270499 bytes_retransmit=9 bytes_invalid=0 send_seq=25768 receive_seq=25768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=42419 freq=400015642 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2284 bytes_read=9075 bytes_retransmit=0 bytes_invalid=0 send_seq=352 receive_seq=352 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997960 adj=49996871 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=12238 bytes_read=141953 bytes_retransmit=9 bytes_invalid=0 send_seq=1309 receive_seq=1309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997700 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11376 bytes_read=44332 bytes_retransmit=9 bytes_invalid=0 send_seq=1095 receive_seq=1095 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997572 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2443 bytes_read=63555 bytes_retransmit=9 bytes_invalid=0 send_seq=358 receive_seq=358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999496 adj=47997701 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3037 bytes_read=8933 bytes_retransmit=9 bytes_invalid=0 send_seq=353 receive_seq=353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.3 EBB42_Gen2_v1.0_T0: temp=28.5 EBB42_Gen2_v1.0_T1: temp=27.6 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46113 bytes_read=303879 bytes_retransmit=0 bytes_invalid=0 send_seq=3990 receive_seq=3990 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31998684 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=41.2 th1: temp=40.4 th2: temp=41.3 th3: temp=39.9 sysload=0.16 cputime=34.810 memavail=7406816 print_time=293.741 buffer_time=2.229 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 270.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1136977 bytes_read=272894 bytes_retransmit=9 bytes_invalid=0 send_seq=26176 receive_seq=26176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=44238 freq=400015628 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2290 bytes_read=9090 bytes_retransmit=0 bytes_invalid=0 send_seq=353 receive_seq=353 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997975 adj=49996861 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=12314 bytes_read=145084 bytes_retransmit=9 bytes_invalid=0 send_seq=1320 receive_seq=1320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997725 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11382 bytes_read=44432 bytes_retransmit=9 bytes_invalid=0 send_seq=1096 receive_seq=1096 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999999 adj=63997604 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2449 bytes_read=63789 bytes_retransmit=9 bytes_invalid=0 send_seq=359 receive_seq=359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999498 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3043 bytes_read=8949 bytes_retransmit=9 bytes_invalid=0 send_seq=354 receive_seq=354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.5 EBB42_Gen2_v1.0_T1: temp=27.8 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46119 bytes_read=304235 bytes_retransmit=0 bytes_invalid=0 send_seq=3991 receive_seq=3991 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31998676 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=41.6 th1: temp=40.6 th2: temp=41.7 th3: temp=39.8 sysload=0.16 cputime=34.962 memavail=7406816 print_time=294.818 buffer_time=2.305 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 271.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1161793 bytes_read=275244 bytes_retransmit=9 bytes_invalid=0 send_seq=26584 receive_seq=26584 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=46094 freq=400015603 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2296 bytes_read=9105 bytes_retransmit=0 bytes_invalid=0 send_seq=354 receive_seq=354 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49997989 adj=49996859 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=12390 bytes_read=148170 bytes_retransmit=9 bytes_invalid=0 send_seq=1331 receive_seq=1331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997712 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11388 bytes_read=44574 bytes_retransmit=9 bytes_invalid=0 send_seq=1097 receive_seq=1097 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997641 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2455 bytes_read=64083 bytes_retransmit=9 bytes_invalid=0 send_seq=360 receive_seq=360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999497 adj=47997723 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3049 bytes_read=8965 bytes_retransmit=9 bytes_invalid=0 send_seq=355 receive_seq=355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.4 EBB42_Gen2_v1.0_T1: temp=27.7 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46125 bytes_read=304591 bytes_retransmit=0 bytes_invalid=0 send_seq=3992 receive_seq=3992 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31998670 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=41.6 th1: temp=40.3 th2: temp=41.5 th3: temp=39.7 sysload=0.15 cputime=35.110 memavail=7406816 print_time=295.894 buffer_time=2.380 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 272.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1186582 bytes_read=277584 bytes_retransmit=9 bytes_invalid=0 send_seq=26990 receive_seq=26990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=47950 freq=400015570 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2302 bytes_read=9134 bytes_retransmit=0 bytes_invalid=0 send_seq=355 receive_seq=355 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998004 adj=49996875 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=12466 bytes_read=151227 bytes_retransmit=9 bytes_invalid=0 send_seq=1342 receive_seq=1342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997739 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11394 bytes_read=44674 bytes_retransmit=9 bytes_invalid=0 send_seq=1098 receive_seq=1098 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997656 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2461 bytes_read=64317 bytes_retransmit=9 bytes_invalid=0 send_seq=361 receive_seq=361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999497 adj=47997730 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3055 bytes_read=8992 bytes_retransmit=9 bytes_invalid=0 send_seq=356 receive_seq=356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.4 EBB42_Gen2_v1.0_T1: temp=27.6 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46131 bytes_read=304947 bytes_retransmit=0 bytes_invalid=0 send_seq=3993 receive_seq=3993 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31998674 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=41.5 th1: temp=40.6 th2: temp=41.8 th3: temp=39.7 sysload=0.15 cputime=35.258 memavail=7406816 print_time=296.971 buffer_time=2.456 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 273.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1211528 bytes_read=279973 bytes_retransmit=9 bytes_invalid=0 send_seq=27400 receive_seq=27400 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=49628 freq=400015549 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2308 bytes_read=9150 bytes_retransmit=0 bytes_invalid=0 send_seq=356 receive_seq=356 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998017 adj=49996908 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=12542 bytes_read=154287 bytes_retransmit=9 bytes_invalid=0 send_seq=1353 receive_seq=1353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997774 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11400 bytes_read=44774 bytes_retransmit=9 bytes_invalid=0 send_seq=1099 receive_seq=1099 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997670 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2467 bytes_read=64566 bytes_retransmit=9 bytes_invalid=0 send_seq=362 receive_seq=362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999496 adj=47997745 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3061 bytes_read=9008 bytes_retransmit=9 bytes_invalid=0 send_seq=357 receive_seq=357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.6 EBB42_Gen2_v1.0_T1: temp=27.8 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46137 bytes_read=305303 bytes_retransmit=0 bytes_invalid=0 send_seq=3994 receive_seq=3994 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31998688 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=41.4 th1: temp=40.7 th2: temp=41.4 th3: temp=40.1 sysload=0.15 cputime=35.407 memavail=7406816 print_time=298.047 buffer_time=2.525 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Write g-code response
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/gcode.py", line 459, in _respond_raw
    os.write(self.fd, (msg+"\n").encode())
BlockingIOError: [Errno 11] Resource temporarily unavailable
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 274.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1236381 bytes_read=282318 bytes_retransmit=9 bytes_invalid=0 send_seq=27807 receive_seq=27807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=39236 freq=400015536 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2314 bytes_read=9166 bytes_retransmit=0 bytes_invalid=0 send_seq=357 receive_seq=357 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998032 adj=49996912 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=12618 bytes_read=157430 bytes_retransmit=9 bytes_invalid=0 send_seq=1364 receive_seq=1364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997784 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11406 bytes_read=44902 bytes_retransmit=9 bytes_invalid=0 send_seq=1100 receive_seq=1100 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997677 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2473 bytes_read=64860 bytes_retransmit=9 bytes_invalid=0 send_seq=363 receive_seq=363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999496 adj=47997743 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3067 bytes_read=9024 bytes_retransmit=9 bytes_invalid=0 send_seq=358 receive_seq=358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.4 EBB42_Gen2_v1.0_T1: temp=27.6 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46143 bytes_read=305659 bytes_retransmit=0 bytes_invalid=0 send_seq=3995 receive_seq=3995 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31998688 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=41.0 th1: temp=40.8 th2: temp=41.7 th3: temp=39.9 sysload=0.15 cputime=35.542 memavail=7406832 print_time=298.585 buffer_time=2.062 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 275.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1261862 bytes_read=284729 bytes_retransmit=9 bytes_invalid=0 send_seq=28224 receive_seq=28224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400015512 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2320 bytes_read=9182 bytes_retransmit=0 bytes_invalid=0 send_seq=358 receive_seq=358 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998046 adj=49997099 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=12694 bytes_read=160504 bytes_retransmit=9 bytes_invalid=0 send_seq=1375 receive_seq=1375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997877 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11412 bytes_read=45002 bytes_retransmit=9 bytes_invalid=0 send_seq=1101 receive_seq=1101 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997697 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2479 bytes_read=65094 bytes_retransmit=9 bytes_invalid=0 send_seq=364 receive_seq=364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999496 adj=47997756 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3073 bytes_read=9040 bytes_retransmit=9 bytes_invalid=0 send_seq=359 receive_seq=359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.6 EBB42_Gen2_v1.0_T1: temp=27.8 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46149 bytes_read=306015 bytes_retransmit=0 bytes_invalid=0 send_seq=3996 receive_seq=3996 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31998702 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=41.9 th1: temp=40.5 th2: temp=41.6 th3: temp=39.9 sysload=0.15 cputime=35.692 memavail=7405832 print_time=299.662 buffer_time=2.138 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 276.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1286967 bytes_read=287118 bytes_retransmit=9 bytes_invalid=0 send_seq=28635 receive_seq=28634 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=42020 freq=400015508 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2326 bytes_read=9198 bytes_retransmit=0 bytes_invalid=0 send_seq=359 receive_seq=359 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998061 adj=49997192 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=12770 bytes_read=163564 bytes_retransmit=9 bytes_invalid=0 send_seq=1386 receive_seq=1386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997895 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11418 bytes_read=45116 bytes_retransmit=9 bytes_invalid=0 send_seq=1102 receive_seq=1102 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997731 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2485 bytes_read=65328 bytes_retransmit=9 bytes_invalid=0 send_seq=365 receive_seq=365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999496 adj=47997781 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3079 bytes_read=9056 bytes_retransmit=9 bytes_invalid=0 send_seq=360 receive_seq=360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999467 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.4 EBB42_Gen2_v1.0_T1: temp=27.6 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46155 bytes_read=306371 bytes_retransmit=0 bytes_invalid=0 send_seq=3997 receive_seq=3997 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31998716 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=41.7 th1: temp=40.5 th2: temp=41.5 th3: temp=40.0 sysload=0.14 cputime=35.839 memavail=7405832 print_time=300.738 buffer_time=2.214 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 277.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1311687 bytes_read=289453 bytes_retransmit=9 bytes_invalid=0 send_seq=29039 receive_seq=29039 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=43908 freq=400015501 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2332 bytes_read=9227 bytes_retransmit=0 bytes_invalid=0 send_seq=360 receive_seq=360 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998075 adj=49997124 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=12846 bytes_read=166649 bytes_retransmit=9 bytes_invalid=0 send_seq=1397 receive_seq=1397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997829 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11424 bytes_read=45244 bytes_retransmit=9 bytes_invalid=0 send_seq=1103 receive_seq=1103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997677 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2491 bytes_read=65622 bytes_retransmit=9 bytes_invalid=0 send_seq=366 receive_seq=366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999495 adj=47997746 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3085 bytes_read=9083 bytes_retransmit=9 bytes_invalid=0 send_seq=361 receive_seq=361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999462 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=28.5 EBB42_Gen2_v1.0_T1: temp=27.7 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46161 bytes_read=306727 bytes_retransmit=0 bytes_invalid=0 send_seq=3998 receive_seq=3998 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31998704 coil_temp=17.6 refs=0 mcu_temp=20.76 supply_voltage=3.012 th0: temp=41.6 th1: temp=40.5 th2: temp=41.5 th3: temp=39.9 sysload=0.14 cputime=35.986 memavail=7405840 print_time=301.815 buffer_time=2.290 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 278.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1336471 bytes_read=291786 bytes_retransmit=9 bytes_invalid=0 send_seq=29444 receive_seq=29444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=45764 freq=400015503 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2338 bytes_read=9243 bytes_retransmit=0 bytes_invalid=0 send_seq=361 receive_seq=361 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998089 adj=49997080 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=12915 bytes_read=169684 bytes_retransmit=9 bytes_invalid=0 send_seq=1407 receive_seq=1407 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997797 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11430 bytes_read=45344 bytes_retransmit=9 bytes_invalid=0 send_seq=1104 receive_seq=1104 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999996 adj=63997653 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2497 bytes_read=65871 bytes_retransmit=9 bytes_invalid=0 send_seq=367 receive_seq=367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999495 adj=47997728 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3091 bytes_read=9099 bytes_retransmit=9 bytes_invalid=0 send_seq=362 receive_seq=362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.4 EBB42_Gen2_v1.0_T1: temp=27.8 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46167 bytes_read=307083 bytes_retransmit=0 bytes_invalid=0 send_seq=3999 receive_seq=3999 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31998694 coil_temp=17.6 refs=0 mcu_temp=20.75 supply_voltage=3.012 th0: temp=41.7 th1: temp=40.7 th2: temp=41.6 th3: temp=40.1 sysload=0.14 cputime=36.128 memavail=7405840 print_time=302.891 buffer_time=2.366 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 279.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1361274 bytes_read=294105 bytes_retransmit=9 bytes_invalid=0 send_seq=29841 receive_seq=29841 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=47588 freq=400015507 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2344 bytes_read=9259 bytes_retransmit=0 bytes_invalid=0 send_seq=362 receive_seq=362 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998103 adj=49997041 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=12991 bytes_read=172742 bytes_retransmit=9 bytes_invalid=0 send_seq=1418 receive_seq=1418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997765 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11436 bytes_read=45444 bytes_retransmit=9 bytes_invalid=0 send_seq=1105 receive_seq=1105 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997611 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2503 bytes_read=66105 bytes_retransmit=9 bytes_invalid=0 send_seq=368 receive_seq=368 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999494 adj=47997701 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3097 bytes_read=9115 bytes_retransmit=9 bytes_invalid=0 send_seq=363 receive_seq=363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.4 EBB42_Gen2_v1.0_T1: temp=27.7 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46173 bytes_read=307439 bytes_retransmit=0 bytes_invalid=0 send_seq=4000 receive_seq=4000 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31998690 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=41.8 th1: temp=40.7 th2: temp=41.6 th3: temp=39.9 sysload=0.14 cputime=36.272 memavail=7405840 print_time=303.968 buffer_time=2.442 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 280.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1386015 bytes_read=296466 bytes_retransmit=9 bytes_invalid=0 send_seq=30248 receive_seq=30248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=49463 freq=400015497 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2350 bytes_read=9275 bytes_retransmit=0 bytes_invalid=0 send_seq=363 receive_seq=363 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998116 adj=49996999 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=13067 bytes_read=175848 bytes_retransmit=9 bytes_invalid=0 send_seq=1429 receive_seq=1429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997723 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11442 bytes_read=45572 bytes_retransmit=9 bytes_invalid=0 send_seq=1106 receive_seq=1106 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999994 adj=63997572 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2509 bytes_read=66399 bytes_retransmit=9 bytes_invalid=0 send_seq=369 receive_seq=369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999494 adj=47997677 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3103 bytes_read=9131 bytes_retransmit=9 bytes_invalid=0 send_seq=364 receive_seq=364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.5 EBB42_Gen2_v1.0_T1: temp=27.7 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46179 bytes_read=307795 bytes_retransmit=0 bytes_invalid=0 send_seq=4001 receive_seq=4001 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999873 adj=31998674 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=41.7 th1: temp=40.6 th2: temp=42.0 th3: temp=40.0 sysload=0.14 cputime=36.423 memavail=7405840 print_time=305.044 buffer_time=2.518 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 281.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1410936 bytes_read=298816 bytes_retransmit=9 bytes_invalid=0 send_seq=30657 receive_seq=30656 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=39036 freq=400015493 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2356 bytes_read=9291 bytes_retransmit=0 bytes_invalid=0 send_seq=364 receive_seq=364 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998131 adj=49996987 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=13143 bytes_read=178905 bytes_retransmit=9 bytes_invalid=0 send_seq=1440 receive_seq=1440 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997729 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11448 bytes_read=45686 bytes_retransmit=9 bytes_invalid=0 send_seq=1107 receive_seq=1107 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999994 adj=63997568 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2515 bytes_read=66633 bytes_retransmit=9 bytes_invalid=0 send_seq=370 receive_seq=370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999493 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3109 bytes_read=9147 bytes_retransmit=9 bytes_invalid=0 send_seq=365 receive_seq=365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.5 EBB42_Gen2_v1.0_T1: temp=27.6 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46185 bytes_read=308151 bytes_retransmit=0 bytes_invalid=0 send_seq=4002 receive_seq=4002 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31998676 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=42.0 th1: temp=40.7 th2: temp=41.7 th3: temp=40.0 sysload=0.13 cputime=36.560 memavail=7405840 print_time=305.582 buffer_time=2.055 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 282.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1436181 bytes_read=301225 bytes_retransmit=9 bytes_invalid=0 send_seq=31070 receive_seq=31070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400015488 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2362 bytes_read=9320 bytes_retransmit=0 bytes_invalid=0 send_seq=365 receive_seq=365 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998146 adj=49997164 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=13219 bytes_read=182019 bytes_retransmit=9 bytes_invalid=0 send_seq=1451 receive_seq=1451 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997725 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11454 bytes_read=45786 bytes_retransmit=9 bytes_invalid=0 send_seq=1108 receive_seq=1108 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999994 adj=63997571 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2521 bytes_read=66867 bytes_retransmit=9 bytes_invalid=0 send_seq=371 receive_seq=371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999493 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3115 bytes_read=9174 bytes_retransmit=9 bytes_invalid=0 send_seq=366 receive_seq=366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.6 EBB42_Gen2_v1.0_T1: temp=27.7 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46191 bytes_read=308507 bytes_retransmit=0 bytes_invalid=0 send_seq=4003 receive_seq=4003 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31998693 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=42.1 th1: temp=40.7 th2: temp=41.7 th3: temp=40.1 sysload=0.13 cputime=36.710 memavail=7405840 print_time=306.659 buffer_time=2.131 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 283.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1461489 bytes_read=303620 bytes_retransmit=9 bytes_invalid=0 send_seq=31487 receive_seq=31487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=41853 freq=400015495 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2368 bytes_read=9336 bytes_retransmit=0 bytes_invalid=0 send_seq=366 receive_seq=366 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998162 adj=49997237 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=13295 bytes_read=185104 bytes_retransmit=9 bytes_invalid=0 send_seq=1462 receive_seq=1462 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997716 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11460 bytes_read=45914 bytes_retransmit=9 bytes_invalid=0 send_seq=1109 receive_seq=1109 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999993 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2527 bytes_read=67176 bytes_retransmit=9 bytes_invalid=0 send_seq=372 receive_seq=372 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999492 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3121 bytes_read=9190 bytes_retransmit=9 bytes_invalid=0 send_seq=367 receive_seq=367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.6 EBB42_Gen2_v1.0_T1: temp=27.8 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46197 bytes_read=308863 bytes_retransmit=0 bytes_invalid=0 send_seq=4004 receive_seq=4004 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31998690 coil_temp=17.6 refs=0 mcu_temp=20.75 supply_voltage=3.012 th0: temp=42.0 th1: temp=40.6 th2: temp=41.8 th3: temp=39.9 sysload=0.13 cputime=36.858 memavail=7405840 print_time=307.735 buffer_time=2.207 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 284.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1486228 bytes_read=305910 bytes_retransmit=9 bytes_invalid=0 send_seq=31883 receive_seq=31883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=43709 freq=400015524 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2374 bytes_read=9352 bytes_retransmit=0 bytes_invalid=0 send_seq=367 receive_seq=367 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998177 adj=49997191 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=13371 bytes_read=188161 bytes_retransmit=9 bytes_invalid=0 send_seq=1473 receive_seq=1473 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997692 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11466 bytes_read=46014 bytes_retransmit=9 bytes_invalid=0 send_seq=1110 receive_seq=1110 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999993 adj=63997544 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2533 bytes_read=67410 bytes_retransmit=9 bytes_invalid=0 send_seq=373 receive_seq=373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999492 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3127 bytes_read=9206 bytes_retransmit=9 bytes_invalid=0 send_seq=368 receive_seq=368 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999900 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.5 EBB42_Gen2_v1.0_T1: temp=27.8 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46203 bytes_read=309219 bytes_retransmit=0 bytes_invalid=0 send_seq=4005 receive_seq=4005 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999874 adj=31998672 coil_temp=17.6 refs=0 mcu_temp=20.75 supply_voltage=3.012 th0: temp=41.9 th1: temp=40.8 th2: temp=41.9 th3: temp=40.1 sysload=0.13 cputime=37.005 memavail=7405876 print_time=308.812 buffer_time=2.283 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 285.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1511022 bytes_read=308300 bytes_retransmit=9 bytes_invalid=0 send_seq=32290 receive_seq=32290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=45532 freq=400015540 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2380 bytes_read=9368 bytes_retransmit=0 bytes_invalid=0 send_seq=368 receive_seq=368 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998190 adj=49997103 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=13447 bytes_read=191236 bytes_retransmit=9 bytes_invalid=0 send_seq=1484 receive_seq=1484 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997645 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11472 bytes_read=46114 bytes_retransmit=9 bytes_invalid=0 send_seq=1111 receive_seq=1111 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999992 adj=63997477 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2539 bytes_read=67644 bytes_retransmit=9 bytes_invalid=0 send_seq=374 receive_seq=374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999493 adj=47997602 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3133 bytes_read=9222 bytes_retransmit=9 bytes_invalid=0 send_seq=369 receive_seq=369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999900 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.7 EBB42_Gen2_v1.0_T1: temp=27.7 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46209 bytes_read=309575 bytes_retransmit=0 bytes_invalid=0 send_seq=4006 receive_seq=4006 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999877 adj=31998637 coil_temp=17.6 refs=0 mcu_temp=20.76 supply_voltage=3.012 th0: temp=41.8 th1: temp=40.8 th2: temp=41.6 th3: temp=40.0 sysload=0.13 cputime=37.152 memavail=7406656 print_time=309.888 buffer_time=2.358 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 286.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1535806 bytes_read=310635 bytes_retransmit=9 bytes_invalid=0 send_seq=32695 receive_seq=32695 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=47388 freq=400015535 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2386 bytes_read=9384 bytes_retransmit=0 bytes_invalid=0 send_seq=369 receive_seq=369 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998204 adj=49997047 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=13523 bytes_read=194321 bytes_retransmit=9 bytes_invalid=0 send_seq=1495 receive_seq=1495 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997611 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11478 bytes_read=46256 bytes_retransmit=9 bytes_invalid=0 send_seq=1112 receive_seq=1112 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999991 adj=63997447 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2545 bytes_read=67938 bytes_retransmit=9 bytes_invalid=0 send_seq=375 receive_seq=375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999492 adj=47997591 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3139 bytes_read=9238 bytes_retransmit=9 bytes_invalid=0 send_seq=370 receive_seq=370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999900 adj=11999421 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.6 EBB42_Gen2_v1.0_T1: temp=27.9 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46215 bytes_read=309931 bytes_retransmit=0 bytes_invalid=0 send_seq=4007 receive_seq=4007 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999878 adj=31998652 coil_temp=17.6 refs=0 mcu_temp=20.76 supply_voltage=3.012 th0: temp=42.0 th1: temp=40.7 th2: temp=42.0 th3: temp=39.9 sysload=0.12 cputime=37.309 memavail=7406772 print_time=310.965 buffer_time=2.434 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 287.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1560583 bytes_read=312940 bytes_retransmit=9 bytes_invalid=0 send_seq=33094 receive_seq=33094 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=49231 freq=400015551 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2392 bytes_read=9413 bytes_retransmit=0 bytes_invalid=0 send_seq=370 receive_seq=370 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998218 adj=49997043 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=13599 bytes_read=197379 bytes_retransmit=9 bytes_invalid=0 send_seq=1506 receive_seq=1506 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997624 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11484 bytes_read=46356 bytes_retransmit=9 bytes_invalid=0 send_seq=1113 receive_seq=1113 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999991 adj=63997459 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2551 bytes_read=68172 bytes_retransmit=9 bytes_invalid=0 send_seq=376 receive_seq=376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999492 adj=47997601 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3145 bytes_read=9265 bytes_retransmit=9 bytes_invalid=0 send_seq=371 receive_seq=371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999900 adj=11999425 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.6 EBB42_Gen2_v1.0_T1: temp=27.8 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46221 bytes_read=310287 bytes_retransmit=0 bytes_invalid=0 send_seq=4008 receive_seq=4008 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999878 adj=31998658 coil_temp=17.6 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=41.8 th1: temp=41.0 th2: temp=41.8 th3: temp=40.0 sysload=0.12 cputime=37.455 memavail=7406772 print_time=312.041 buffer_time=2.510 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 288.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1585350 bytes_read=315304 bytes_retransmit=9 bytes_invalid=0 send_seq=33499 receive_seq=33499 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=38871 freq=400015540 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2398 bytes_read=9429 bytes_retransmit=0 bytes_invalid=0 send_seq=371 receive_seq=371 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998233 adj=49997021 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=13675 bytes_read=200437 bytes_retransmit=9 bytes_invalid=0 send_seq=1517 receive_seq=1517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997609 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11490 bytes_read=46456 bytes_retransmit=9 bytes_invalid=0 send_seq=1114 receive_seq=1114 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999992 adj=63997436 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2557 bytes_read=68421 bytes_retransmit=9 bytes_invalid=0 send_seq=377 receive_seq=377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999492 adj=47997583 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3151 bytes_read=9281 bytes_retransmit=9 bytes_invalid=0 send_seq=372 receive_seq=372 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999900 adj=11999421 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.6 EBB42_Gen2_v1.0_T1: temp=27.8 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46227 bytes_read=310643 bytes_retransmit=0 bytes_invalid=0 send_seq=4009 receive_seq=4009 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999878 adj=31998645 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=41.8 th1: temp=40.8 th2: temp=42.2 th3: temp=39.9 sysload=0.12 cputime=37.594 memavail=7406772 print_time=312.579 buffer_time=2.048 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 289.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1610425 bytes_read=317620 bytes_retransmit=9 bytes_invalid=0 send_seq=33901 receive_seq=33901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400015527 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2404 bytes_read=9445 bytes_retransmit=0 bytes_invalid=0 send_seq=372 receive_seq=372 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998247 adj=49997202 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=13744 bytes_read=203556 bytes_retransmit=9 bytes_invalid=0 send_seq=1527 receive_seq=1527 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997645 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11496 bytes_read=46584 bytes_retransmit=9 bytes_invalid=0 send_seq=1115 receive_seq=1115 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999992 adj=63997474 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2563 bytes_read=68715 bytes_retransmit=9 bytes_invalid=0 send_seq=378 receive_seq=378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999492 adj=47997597 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3157 bytes_read=9297 bytes_retransmit=9 bytes_invalid=0 send_seq=373 receive_seq=373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.5 EBB42_Gen2_v1.0_T1: temp=27.8 raspberry_pi: temp=22.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46233 bytes_read=310999 bytes_retransmit=0 bytes_invalid=0 send_seq=4010 receive_seq=4010 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999878 adj=31998652 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=41.8 th1: temp=41.2 th2: temp=41.5 th3: temp=40.1 sysload=0.12 cputime=37.740 memavail=7406772 print_time=313.656 buffer_time=2.124 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 290.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1635901 bytes_read=320040 bytes_retransmit=9 bytes_invalid=0 send_seq=34320 receive_seq=34320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=41686 freq=400015540 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2410 bytes_read=9461 bytes_retransmit=0 bytes_invalid=0 send_seq=373 receive_seq=373 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998261 adj=49997294 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=13820 bytes_read=206629 bytes_retransmit=9 bytes_invalid=0 send_seq=1538 receive_seq=1538 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997662 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11502 bytes_read=46684 bytes_retransmit=9 bytes_invalid=0 send_seq=1116 receive_seq=1116 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999992 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2569 bytes_read=68949 bytes_retransmit=9 bytes_invalid=0 send_seq=379 receive_seq=379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999492 adj=47997626 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3163 bytes_read=9313 bytes_retransmit=9 bytes_invalid=0 send_seq=374 receive_seq=374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999900 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.5 EBB42_Gen2_v1.0_T1: temp=28.0 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46239 bytes_read=311355 bytes_retransmit=0 bytes_invalid=0 send_seq=4011 receive_seq=4011 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999877 adj=31998660 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=41.9 th1: temp=40.8 th2: temp=41.7 th3: temp=40.1 sysload=0.12 cputime=37.889 memavail=7406772 print_time=314.732 buffer_time=2.200 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 291.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1660700 bytes_read=322419 bytes_retransmit=9 bytes_invalid=0 send_seq=34728 receive_seq=34728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=43542 freq=400015540 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2416 bytes_read=9477 bytes_retransmit=0 bytes_invalid=0 send_seq=374 receive_seq=374 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998275 adj=49997215 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=13896 bytes_read=209685 bytes_retransmit=9 bytes_invalid=0 send_seq=1549 receive_seq=1549 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997726 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11508 bytes_read=46798 bytes_retransmit=9 bytes_invalid=0 send_seq=1117 receive_seq=1117 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999991 adj=63997473 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2575 bytes_read=69183 bytes_retransmit=9 bytes_invalid=0 send_seq=380 receive_seq=380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999493 adj=47997607 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3169 bytes_read=9329 bytes_retransmit=9 bytes_invalid=0 send_seq=375 receive_seq=375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.5 EBB42_Gen2_v1.0_T1: temp=27.8 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46245 bytes_read=311711 bytes_retransmit=0 bytes_invalid=0 send_seq=4012 receive_seq=4012 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999880 adj=31998639 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=42.1 th1: temp=40.9 th2: temp=41.9 th3: temp=40.2 sysload=0.11 cputime=38.037 memavail=7406772 print_time=315.809 buffer_time=2.275 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 292.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1685522 bytes_read=324775 bytes_retransmit=9 bytes_invalid=0 send_seq=35135 receive_seq=35135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=45398 freq=400015642 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2428 bytes_read=9522 bytes_retransmit=0 bytes_invalid=0 send_seq=376 receive_seq=376 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998302 adj=49997178 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=13978 bytes_read=212788 bytes_retransmit=9 bytes_invalid=0 send_seq=1561 receive_seq=1561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997702 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11520 bytes_read=46942 bytes_retransmit=9 bytes_invalid=0 send_seq=1119 receive_seq=1119 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999992 adj=63997475 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2587 bytes_read=69493 bytes_retransmit=9 bytes_invalid=0 send_seq=382 receive_seq=382 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999493 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3181 bytes_read=9372 bytes_retransmit=9 bytes_invalid=0 send_seq=377 receive_seq=377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.6 EBB42_Gen2_v1.0_T1: temp=27.7 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46257 bytes_read=312083 bytes_retransmit=0 bytes_invalid=0 send_seq=4014 receive_seq=4014 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999879 adj=31998676 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=42.1 th1: temp=40.8 th2: temp=41.9 th3: temp=40.2 sysload=0.11 cputime=38.188 memavail=7406772 print_time=316.885 buffer_time=2.351 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 293.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1710284 bytes_read=327115 bytes_retransmit=9 bytes_invalid=0 send_seq=35541 receive_seq=35541 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=47254 freq=400015723 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2434 bytes_read=9538 bytes_retransmit=0 bytes_invalid=0 send_seq=377 receive_seq=377 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998316 adj=49997159 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=14054 bytes_read=215847 bytes_retransmit=9 bytes_invalid=0 send_seq=1572 receive_seq=1572 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997490 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11526 bytes_read=47042 bytes_retransmit=9 bytes_invalid=0 send_seq=1120 receive_seq=1120 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999992 adj=63997307 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2593 bytes_read=69742 bytes_retransmit=9 bytes_invalid=0 send_seq=383 receive_seq=383 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999494 adj=47997481 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3187 bytes_read=9388 bytes_retransmit=9 bytes_invalid=0 send_seq=378 receive_seq=378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999404 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.7 EBB42_Gen2_v1.0_T1: temp=27.8 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46263 bytes_read=312439 bytes_retransmit=0 bytes_invalid=0 send_seq=4015 receive_seq=4015 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999880 adj=31998563 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=41.9 th1: temp=40.7 th2: temp=42.0 th3: temp=40.3 sysload=0.11 cputime=38.333 memavail=7406772 print_time=317.962 buffer_time=2.427 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 294.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1735118 bytes_read=329489 bytes_retransmit=9 bytes_invalid=0 send_seq=35948 receive_seq=35948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=49067 freq=400015700 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2440 bytes_read=9554 bytes_retransmit=0 bytes_invalid=0 send_seq=378 receive_seq=378 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998330 adj=49997030 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=14130 bytes_read=218904 bytes_retransmit=9 bytes_invalid=0 send_seq=1583 receive_seq=1583 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997373 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11532 bytes_read=47142 bytes_retransmit=9 bytes_invalid=0 send_seq=1121 receive_seq=1121 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999992 adj=63997206 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2599 bytes_read=69976 bytes_retransmit=9 bytes_invalid=0 send_seq=384 receive_seq=384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999494 adj=47997419 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3193 bytes_read=9404 bytes_retransmit=9 bytes_invalid=0 send_seq=379 receive_seq=379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999383 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.7 EBB42_Gen2_v1.0_T1: temp=27.8 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46269 bytes_read=312795 bytes_retransmit=0 bytes_invalid=0 send_seq=4016 receive_seq=4016 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999880 adj=31998520 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=42.1 th1: temp=40.9 th2: temp=41.7 th3: temp=40.3 sysload=0.11 cputime=38.474 memavail=7406772 print_time=319.038 buffer_time=2.503 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 295.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1759912 bytes_read=331850 bytes_retransmit=9 bytes_invalid=0 send_seq=36355 receive_seq=36355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=38707 freq=400015672 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2446 bytes_read=9570 bytes_retransmit=0 bytes_invalid=0 send_seq=379 receive_seq=379 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998347 adj=49997080 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=14206 bytes_read=222006 bytes_retransmit=9 bytes_invalid=0 send_seq=1594 receive_seq=1594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997471 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11538 bytes_read=47270 bytes_retransmit=9 bytes_invalid=0 send_seq=1122 receive_seq=1122 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999991 adj=63997300 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2605 bytes_read=70270 bytes_retransmit=9 bytes_invalid=0 send_seq=385 receive_seq=385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999494 adj=47997485 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3199 bytes_read=9420 bytes_retransmit=9 bytes_invalid=0 send_seq=380 receive_seq=380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999402 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.6 EBB42_Gen2_v1.0_T1: temp=28.0 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46275 bytes_read=313151 bytes_retransmit=0 bytes_invalid=0 send_seq=4017 receive_seq=4017 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999880 adj=31998557 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=41.9 th1: temp=40.9 th2: temp=41.8 th3: temp=40.5 sysload=0.11 cputime=38.610 memavail=7406532 print_time=319.576 buffer_time=2.040 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 296.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1784814 bytes_read=334205 bytes_retransmit=9 bytes_invalid=0 send_seq=36764 receive_seq=36764 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=40461 freq=400015685 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2452 bytes_read=9586 bytes_retransmit=0 bytes_invalid=0 send_seq=380 receive_seq=380 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998365 adj=49997307 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=14282 bytes_read=225122 bytes_retransmit=9 bytes_invalid=0 send_seq=1605 receive_seq=1605 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000181 adj=63997504 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11544 bytes_read=47384 bytes_retransmit=9 bytes_invalid=0 send_seq=1123 receive_seq=1123 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999991 adj=63997341 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2611 bytes_read=70504 bytes_retransmit=9 bytes_invalid=0 send_seq=386 receive_seq=386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999494 adj=47997522 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3205 bytes_read=9436 bytes_retransmit=9 bytes_invalid=0 send_seq=381 receive_seq=381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999412 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.8 EBB42_Gen2_v1.0_T1: temp=27.9 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46281 bytes_read=313507 bytes_retransmit=0 bytes_invalid=0 send_seq=4018 receive_seq=4018 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998580 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=42.1 th1: temp=40.5 th2: temp=42.1 th3: temp=40.2 sysload=0.18 cputime=38.757 memavail=7406532 print_time=320.653 buffer_time=2.117 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 297.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1810490 bytes_read=336649 bytes_retransmit=9 bytes_invalid=0 send_seq=37185 receive_seq=37185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=41491 freq=400015664 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2458 bytes_read=9615 bytes_retransmit=0 bytes_invalid=0 send_seq=381 receive_seq=381 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998387 adj=49997403 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=14358 bytes_read=228179 bytes_retransmit=9 bytes_invalid=0 send_seq=1616 receive_seq=1616 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997489 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11550 bytes_read=47484 bytes_retransmit=9 bytes_invalid=0 send_seq=1124 receive_seq=1124 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997331 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=2617 bytes_read=70738 bytes_retransmit=9 bytes_invalid=0 send_seq=387 receive_seq=387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999494 adj=47997514 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3211 bytes_read=9463 bytes_retransmit=9 bytes_invalid=0 send_seq=382 receive_seq=382 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999408 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.7 EBB42_Gen2_v1.0_T1: temp=27.8 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46287 bytes_read=313863 bytes_retransmit=0 bytes_invalid=0 send_seq=4019 receive_seq=4019 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999884 adj=31998606 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=42.2 th1: temp=41.2 th2: temp=42.0 th3: temp=40.2 sysload=0.18 cputime=38.906 memavail=7406532 print_time=321.729 buffer_time=2.192 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 298.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1835297 bytes_read=338989 bytes_retransmit=9 bytes_invalid=0 send_seq=37591 receive_seq=37591 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=43347 freq=400015652 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2464 bytes_read=9631 bytes_retransmit=0 bytes_invalid=0 send_seq=382 receive_seq=382 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998410 adj=49997466 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=14434 bytes_read=231264 bytes_retransmit=9 bytes_invalid=0 send_seq=1627 receive_seq=1627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997558 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11556 bytes_read=47612 bytes_retransmit=9 bytes_invalid=0 send_seq=1125 receive_seq=1125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997473 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2623 bytes_read=71047 bytes_retransmit=9 bytes_invalid=0 send_seq=388 receive_seq=388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999494 adj=47997565 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3217 bytes_read=9479 bytes_retransmit=9 bytes_invalid=0 send_seq=383 receive_seq=383 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999420 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.8 EBB42_Gen2_v1.0_T1: temp=27.7 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46293 bytes_read=314219 bytes_retransmit=0 bytes_invalid=0 send_seq=4020 receive_seq=4020 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999883 adj=31998651 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=41.9 th1: temp=41.0 th2: temp=41.4 th3: temp=40.4 sysload=0.18 cputime=39.055 memavail=7406532 print_time=322.806 buffer_time=2.268 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.5 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 299.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1860068 bytes_read=341329 bytes_retransmit=9 bytes_invalid=0 send_seq=37997 receive_seq=37997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=45203 freq=400015628 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2470 bytes_read=9647 bytes_retransmit=0 bytes_invalid=0 send_seq=383 receive_seq=383 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998435 adj=49997520 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=14510 bytes_read=234321 bytes_retransmit=9 bytes_invalid=0 send_seq=1638 receive_seq=1638 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997613 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11562 bytes_read=47712 bytes_retransmit=9 bytes_invalid=0 send_seq=1126 receive_seq=1126 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997513 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2629 bytes_read=71281 bytes_retransmit=9 bytes_invalid=0 send_seq=389 receive_seq=389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999494 adj=47997599 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3223 bytes_read=9495 bytes_retransmit=9 bytes_invalid=0 send_seq=384 receive_seq=384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.6 EBB42_Gen2_v1.0_T1: temp=27.9 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46299 bytes_read=314575 bytes_retransmit=0 bytes_invalid=0 send_seq=4021 receive_seq=4021 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998647 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=42.3 th1: temp=40.8 th2: temp=42.0 th3: temp=40.4 sysload=0.18 cputime=39.208 memavail=7406588 print_time=323.882 buffer_time=2.344 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 300.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1884885 bytes_read=343719 bytes_retransmit=9 bytes_invalid=0 send_seq=38405 receive_seq=38405 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=47059 freq=400015602 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2476 bytes_read=9663 bytes_retransmit=0 bytes_invalid=0 send_seq=384 receive_seq=384 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998464 adj=49997607 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=14586 bytes_read=237397 bytes_retransmit=9 bytes_invalid=0 send_seq=1649 receive_seq=1649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000179 adj=63997659 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11568 bytes_read=47812 bytes_retransmit=9 bytes_invalid=0 send_seq=1127 receive_seq=1127 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999999 adj=63997541 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2635 bytes_read=71515 bytes_retransmit=9 bytes_invalid=0 send_seq=390 receive_seq=390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999494 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3229 bytes_read=9511 bytes_retransmit=9 bytes_invalid=0 send_seq=385 receive_seq=385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999901 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=28.6 EBB42_Gen2_v1.0_T1: temp=27.8 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46305 bytes_read=314931 bytes_retransmit=0 bytes_invalid=0 send_seq=4022 receive_seq=4022 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998658 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=42.3 th1: temp=41.0 th2: temp=41.9 th3: temp=40.4 sysload=0.18 cputime=39.355 memavail=7406588 print_time=324.959 buffer_time=2.420 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 301.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1909742 bytes_read=346074 bytes_retransmit=9 bytes_invalid=0 send_seq=38814 receive_seq=38814 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=48871 freq=400015581 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2482 bytes_read=9679 bytes_retransmit=0 bytes_invalid=0 send_seq=385 receive_seq=385 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998491 adj=49997728 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=14655 bytes_read=240458 bytes_retransmit=9 bytes_invalid=0 send_seq=1659 receive_seq=1659 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997697 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11574 bytes_read=47954 bytes_retransmit=9 bytes_invalid=0 send_seq=1128 receive_seq=1128 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997597 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2641 bytes_read=71809 bytes_retransmit=9 bytes_invalid=0 send_seq=391 receive_seq=391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999494 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3235 bytes_read=9527 bytes_retransmit=9 bytes_invalid=0 send_seq=386 receive_seq=386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.5 EBB42_Gen2_v1.0_T1: temp=27.8 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46311 bytes_read=315287 bytes_retransmit=0 bytes_invalid=0 send_seq=4023 receive_seq=4023 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998674 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=42.3 th1: temp=40.8 th2: temp=41.8 th3: temp=40.4 sysload=0.16 cputime=39.505 memavail=7406596 print_time=326.035 buffer_time=2.495 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 302.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1934530 bytes_read=348404 bytes_retransmit=9 bytes_invalid=0 send_seq=39218 receive_seq=39218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=38505 freq=400015565 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2488 bytes_read=9708 bytes_retransmit=0 bytes_invalid=0 send_seq=386 receive_seq=386 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998519 adj=49997791 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=14731 bytes_read=243514 bytes_retransmit=9 bytes_invalid=0 send_seq=1670 receive_seq=1670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997743 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11580 bytes_read=48054 bytes_retransmit=9 bytes_invalid=0 send_seq=1129 receive_seq=1129 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997683 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2647 bytes_read=72043 bytes_retransmit=9 bytes_invalid=0 send_seq=392 receive_seq=392 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999495 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3241 bytes_read=9554 bytes_retransmit=9 bytes_invalid=0 send_seq=387 receive_seq=387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.5 EBB42_Gen2_v1.0_T1: temp=28.0 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46317 bytes_read=315643 bytes_retransmit=0 bytes_invalid=0 send_seq=4024 receive_seq=4024 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999883 adj=31998679 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=42.2 th1: temp=40.8 th2: temp=42.3 th3: temp=40.3 sysload=0.16 cputime=39.638 memavail=7406596 print_time=326.573 buffer_time=2.032 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 303.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1959342 bytes_read=350778 bytes_retransmit=9 bytes_invalid=0 send_seq=39625 receive_seq=39625 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=40361 freq=400015540 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2494 bytes_read=9724 bytes_retransmit=0 bytes_invalid=0 send_seq=387 receive_seq=387 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998549 adj=49998143 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=14807 bytes_read=246629 bytes_retransmit=9 bytes_invalid=0 send_seq=1681 receive_seq=1681 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997771 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11586 bytes_read=48154 bytes_retransmit=9 bytes_invalid=0 send_seq=1130 receive_seq=1130 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997700 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2653 bytes_read=72292 bytes_retransmit=9 bytes_invalid=0 send_seq=393 receive_seq=393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999495 adj=47997710 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3247 bytes_read=9570 bytes_retransmit=9 bytes_invalid=0 send_seq=388 receive_seq=388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=28.7 EBB42_Gen2_v1.0_T1: temp=27.9 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46323 bytes_read=315999 bytes_retransmit=0 bytes_invalid=0 send_seq=4025 receive_seq=4025 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998709 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=42.1 th1: temp=41.0 th2: temp=42.2 th3: temp=40.3 sysload=0.16 cputime=39.801 memavail=7407204 print_time=327.650 buffer_time=2.108 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 304.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=1985129 bytes_read=353188 bytes_retransmit=9 bytes_invalid=0 send_seq=40045 receive_seq=40045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=41289 freq=400015520 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2500 bytes_read=9740 bytes_retransmit=0 bytes_invalid=0 send_seq=388 receive_seq=388 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998580 adj=49998359 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=14883 bytes_read=249714 bytes_retransmit=9 bytes_invalid=0 send_seq=1692 receive_seq=1692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997809 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11592 bytes_read=48282 bytes_retransmit=9 bytes_invalid=0 send_seq=1131 receive_seq=1131 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997721 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2659 bytes_read=72586 bytes_retransmit=9 bytes_invalid=0 send_seq=394 receive_seq=394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999495 adj=47997746 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3253 bytes_read=9586 bytes_retransmit=9 bytes_invalid=0 send_seq=389 receive_seq=389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.7 EBB42_Gen2_v1.0_T1: temp=27.9 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46329 bytes_read=316355 bytes_retransmit=0 bytes_invalid=0 send_seq=4026 receive_seq=4026 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998715 coil_temp=17.7 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=42.2 th1: temp=41.4 th2: temp=42.3 th3: temp=40.1 sysload=0.16 cputime=39.952 memavail=7407204 print_time=328.726 buffer_time=2.183 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 305.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2009895 bytes_read=355539 bytes_retransmit=9 bytes_invalid=0 send_seq=40450 receive_seq=40450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=43145 freq=400015508 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2506 bytes_read=9756 bytes_retransmit=0 bytes_invalid=0 send_seq=389 receive_seq=389 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998612 adj=49998358 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=14959 bytes_read=252789 bytes_retransmit=9 bytes_invalid=0 send_seq=1703 receive_seq=1703 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997808 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11598 bytes_read=48382 bytes_retransmit=9 bytes_invalid=0 send_seq=1132 receive_seq=1132 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997705 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2665 bytes_read=72820 bytes_retransmit=9 bytes_invalid=0 send_seq=395 receive_seq=395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999495 adj=47997746 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3259 bytes_read=9602 bytes_retransmit=9 bytes_invalid=0 send_seq=390 receive_seq=390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999467 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.8 EBB42_Gen2_v1.0_T1: temp=28.0 raspberry_pi: temp=23.4  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46335 bytes_read=316711 bytes_retransmit=0 bytes_invalid=0 send_seq=4027 receive_seq=4027 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999881 adj=31998708 coil_temp=17.7 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=42.2 th1: temp=41.2 th2: temp=42.1 th3: temp=40.5 sysload=0.16 cputime=40.099 memavail=7406520 print_time=329.803 buffer_time=2.259 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 306.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2034689 bytes_read=357913 bytes_retransmit=9 bytes_invalid=0 send_seq=40857 receive_seq=40857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=45001 freq=400015505 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2512 bytes_read=9772 bytes_retransmit=0 bytes_invalid=0 send_seq=390 receive_seq=390 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998645 adj=49998365 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=15035 bytes_read=255846 bytes_retransmit=9 bytes_invalid=0 send_seq=1714 receive_seq=1714 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000177 adj=63997796 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11604 bytes_read=48496 bytes_retransmit=9 bytes_invalid=0 send_seq=1133 receive_seq=1133 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997689 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2671 bytes_read=73054 bytes_retransmit=9 bytes_invalid=0 send_seq=396 receive_seq=396 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999495 adj=47997742 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3265 bytes_read=9618 bytes_retransmit=9 bytes_invalid=0 send_seq=391 receive_seq=391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.9 EBB42_Gen2_v1.0_T1: temp=28.0 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46341 bytes_read=317067 bytes_retransmit=0 bytes_invalid=0 send_seq=4028 receive_seq=4028 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998698 coil_temp=17.7 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=42.4 th1: temp=41.3 th2: temp=42.1 th3: temp=40.4 sysload=0.15 cputime=40.247 memavail=7406520 print_time=330.879 buffer_time=2.335 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 307.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2059473 bytes_read=360248 bytes_retransmit=9 bytes_invalid=0 send_seq=41262 receive_seq=41262 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=46857 freq=400015496 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2518 bytes_read=9801 bytes_retransmit=0 bytes_invalid=0 send_seq=391 receive_seq=391 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998677 adj=49998375 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=15111 bytes_read=258931 bytes_retransmit=9 bytes_invalid=0 send_seq=1725 receive_seq=1725 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000181 adj=63997777 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11610 bytes_read=48624 bytes_retransmit=9 bytes_invalid=0 send_seq=1134 receive_seq=1134 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000002 adj=63997652 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2677 bytes_read=73348 bytes_retransmit=9 bytes_invalid=0 send_seq=397 receive_seq=397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999495 adj=47997723 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3271 bytes_read=9645 bytes_retransmit=9 bytes_invalid=0 send_seq=392 receive_seq=392 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.6 EBB42_Gen2_v1.0_T1: temp=28.0 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46347 bytes_read=317423 bytes_retransmit=0 bytes_invalid=0 send_seq=4029 receive_seq=4029 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998705 coil_temp=17.7 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=42.1 th1: temp=40.8 th2: temp=42.2 th3: temp=40.4 sysload=0.15 cputime=40.397 memavail=7406520 print_time=331.956 buffer_time=2.411 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 308.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2084219 bytes_read=362573 bytes_retransmit=9 bytes_invalid=0 send_seq=41665 receive_seq=41665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=48711 freq=400015514 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2524 bytes_read=9817 bytes_retransmit=0 bytes_invalid=0 send_seq=392 receive_seq=392 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998710 adj=49998395 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=15187 bytes_read=261987 bytes_retransmit=9 bytes_invalid=0 send_seq=1736 receive_seq=1736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997816 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11616 bytes_read=48724 bytes_retransmit=9 bytes_invalid=0 send_seq=1135 receive_seq=1135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000002 adj=63997629 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2683 bytes_read=73597 bytes_retransmit=9 bytes_invalid=0 send_seq=398 receive_seq=398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999495 adj=47997716 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3277 bytes_read=9661 bytes_retransmit=9 bytes_invalid=0 send_seq=393 receive_seq=393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.8 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46353 bytes_read=317779 bytes_retransmit=0 bytes_invalid=0 send_seq=4030 receive_seq=4030 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998693 coil_temp=17.7 refs=0 mcu_temp=20.82 supply_voltage=3.011 th0: temp=42.0 th1: temp=41.2 th2: temp=42.1 th3: temp=40.5 sysload=0.15 cputime=40.543 memavail=7406520 print_time=333.032 buffer_time=2.487 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 309.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2109069 bytes_read=364952 bytes_retransmit=9 bytes_invalid=0 send_seq=42073 receive_seq=42073 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=38308 freq=400015503 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2530 bytes_read=9833 bytes_retransmit=0 bytes_invalid=0 send_seq=393 receive_seq=393 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998744 adj=49998385 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=15263 bytes_read=265043 bytes_retransmit=9 bytes_invalid=0 send_seq=1747 receive_seq=1747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997749 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11622 bytes_read=48824 bytes_retransmit=9 bytes_invalid=0 send_seq=1136 receive_seq=1136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000001 adj=63997576 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2689 bytes_read=73831 bytes_retransmit=9 bytes_invalid=0 send_seq=399 receive_seq=399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999495 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3283 bytes_read=9677 bytes_retransmit=9 bytes_invalid=0 send_seq=394 receive_seq=394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=28.7 EBB42_Gen2_v1.0_T1: temp=27.9 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46359 bytes_read=318135 bytes_retransmit=0 bytes_invalid=0 send_seq=4031 receive_seq=4031 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999886 adj=31998664 coil_temp=17.7 refs=0 mcu_temp=20.82 supply_voltage=3.011 th0: temp=42.3 th1: temp=41.2 th2: temp=42.3 th3: temp=40.6 sysload=0.15 cputime=40.671 memavail=7406520 print_time=333.570 buffer_time=2.024 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 310.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2133889 bytes_read=367323 bytes_retransmit=9 bytes_invalid=0 send_seq=42482 receive_seq=42482 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=40164 freq=400015486 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2536 bytes_read=9849 bytes_retransmit=0 bytes_invalid=0 send_seq=394 receive_seq=394 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998779 adj=49998796 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=15339 bytes_read=268202 bytes_retransmit=9 bytes_invalid=0 send_seq=1758 receive_seq=1758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997820 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11628 bytes_read=48952 bytes_retransmit=9 bytes_invalid=0 send_seq=1137 receive_seq=1137 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000000 adj=63997582 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2695 bytes_read=74125 bytes_retransmit=9 bytes_invalid=0 send_seq=400 receive_seq=400 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999495 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3289 bytes_read=9693 bytes_retransmit=9 bytes_invalid=0 send_seq=395 receive_seq=395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=28.8 EBB42_Gen2_v1.0_T1: temp=28.0 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46365 bytes_read=318491 bytes_retransmit=0 bytes_invalid=0 send_seq=4032 receive_seq=4032 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999885 adj=31998725 coil_temp=17.7 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=42.2 th1: temp=41.2 th2: temp=42.2 th3: temp=40.3 sysload=0.15 cputime=40.818 memavail=7406520 print_time=334.647 buffer_time=2.100 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 311.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2159680 bytes_read=369762 bytes_retransmit=9 bytes_invalid=0 send_seq=42906 receive_seq=42906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=41092 freq=400015478 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2542 bytes_read=9865 bytes_retransmit=0 bytes_invalid=0 send_seq=395 receive_seq=395 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998815 adj=49999011 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=15415 bytes_read=271260 bytes_retransmit=9 bytes_invalid=0 send_seq=1769 receive_seq=1769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000181 adj=63997823 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11634 bytes_read=49052 bytes_retransmit=9 bytes_invalid=0 send_seq=1138 receive_seq=1138 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999999 adj=63997599 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2701 bytes_read=74359 bytes_retransmit=9 bytes_invalid=0 send_seq=401 receive_seq=401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999495 adj=47997703 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3295 bytes_read=9709 bytes_retransmit=9 bytes_invalid=0 send_seq=396 receive_seq=396 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=28.9 EBB42_Gen2_v1.0_T1: temp=28.0 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46371 bytes_read=318831 bytes_retransmit=0 bytes_invalid=0 send_seq=4033 receive_seq=4033 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999886 adj=31998723 coil_temp=17.7 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=42.5 th1: temp=41.2 th2: temp=42.0 th3: temp=40.5 sysload=0.46 cputime=40.969 memavail=7406520 print_time=335.723 buffer_time=2.176 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 312.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2184479 bytes_read=372127 bytes_retransmit=9 bytes_invalid=0 send_seq=43314 receive_seq=43314 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=42980 freq=400015468 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2548 bytes_read=9881 bytes_retransmit=0 bytes_invalid=0 send_seq=396 receive_seq=396 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998850 adj=49998958 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=15491 bytes_read=274310 bytes_retransmit=9 bytes_invalid=0 send_seq=1780 receive_seq=1780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997858 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11640 bytes_read=49161 bytes_retransmit=9 bytes_invalid=0 send_seq=1139 receive_seq=1139 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997584 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2707 bytes_read=74593 bytes_retransmit=9 bytes_invalid=0 send_seq=402 receive_seq=402 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999496 adj=47997698 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3301 bytes_read=9736 bytes_retransmit=9 bytes_invalid=0 send_seq=397 receive_seq=397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.8 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46377 bytes_read=319187 bytes_retransmit=0 bytes_invalid=0 send_seq=4034 receive_seq=4034 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999885 adj=31998725 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=42.6 th1: temp=41.6 th2: temp=42.1 th3: temp=40.4 sysload=0.46 cputime=41.123 memavail=7406536 print_time=336.800 buffer_time=2.252 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 313.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2209240 bytes_read=374482 bytes_retransmit=9 bytes_invalid=0 send_seq=43723 receive_seq=43723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=44836 freq=400015460 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2554 bytes_read=9910 bytes_retransmit=0 bytes_invalid=0 send_seq=397 receive_seq=397 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998885 adj=49998926 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=15560 bytes_read=277353 bytes_retransmit=9 bytes_invalid=0 send_seq=1790 receive_seq=1790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000179 adj=63997826 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11646 bytes_read=49279 bytes_retransmit=9 bytes_invalid=0 send_seq=1140 receive_seq=1140 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997579 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2713 bytes_read=74902 bytes_retransmit=9 bytes_invalid=0 send_seq=403 receive_seq=403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999495 adj=47997711 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3307 bytes_read=9752 bytes_retransmit=9 bytes_invalid=0 send_seq=398 receive_seq=398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.9 EBB42_Gen2_v1.0_T1: temp=27.9 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46383 bytes_read=319543 bytes_retransmit=0 bytes_invalid=0 send_seq=4035 receive_seq=4035 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999884 adj=31998707 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=42.4 th1: temp=41.2 th2: temp=42.3 th3: temp=40.2 sysload=0.46 cputime=41.270 memavail=7406536 print_time=337.876 buffer_time=2.328 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 314.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2234103 bytes_read=376851 bytes_retransmit=9 bytes_invalid=0 send_seq=44132 receive_seq=44132 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=46660 freq=400015446 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2560 bytes_read=9926 bytes_retransmit=0 bytes_invalid=0 send_seq=398 receive_seq=398 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998919 adj=49998901 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=15636 bytes_read=280396 bytes_retransmit=9 bytes_invalid=0 send_seq=1801 receive_seq=1801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000179 adj=63997806 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11652 bytes_read=49372 bytes_retransmit=9 bytes_invalid=0 send_seq=1141 receive_seq=1141 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997571 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2719 bytes_read=75136 bytes_retransmit=9 bytes_invalid=0 send_seq=404 receive_seq=404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999495 adj=47997702 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3313 bytes_read=9768 bytes_retransmit=9 bytes_invalid=0 send_seq=399 receive_seq=399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.8 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46389 bytes_read=319899 bytes_retransmit=0 bytes_invalid=0 send_seq=4036 receive_seq=4036 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999885 adj=31998689 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=42.0 th1: temp=41.3 th2: temp=42.1 th3: temp=40.5 sysload=0.46 cputime=41.422 memavail=7406536 print_time=338.953 buffer_time=2.403 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 315.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2258905 bytes_read=379227 bytes_retransmit=9 bytes_invalid=0 send_seq=44539 receive_seq=44539 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=48481 freq=400015427 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2566 bytes_read=9942 bytes_retransmit=0 bytes_invalid=0 send_seq=399 receive_seq=399 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998955 adj=49998886 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=15712 bytes_read=283452 bytes_retransmit=9 bytes_invalid=0 send_seq=1812 receive_seq=1812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997801 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11658 bytes_read=49465 bytes_retransmit=9 bytes_invalid=0 send_seq=1142 receive_seq=1142 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000002 adj=63997593 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2725 bytes_read=75385 bytes_retransmit=9 bytes_invalid=0 send_seq=405 receive_seq=405 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999495 adj=47997706 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3319 bytes_read=9784 bytes_retransmit=9 bytes_invalid=0 send_seq=400 receive_seq=400 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.9 EBB42_Gen2_v1.0_T1: temp=27.8 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46395 bytes_read=320255 bytes_retransmit=0 bytes_invalid=0 send_seq=4037 receive_seq=4037 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999884 adj=31998702 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=42.5 th1: temp=41.2 th2: temp=42.3 th3: temp=40.6 sysload=0.46 cputime=41.577 memavail=7406284 print_time=340.029 buffer_time=2.479 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 316.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2283765 bytes_read=381582 bytes_retransmit=9 bytes_invalid=0 send_seq=44948 receive_seq=44948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=38108 freq=400015423 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2572 bytes_read=9958 bytes_retransmit=0 bytes_invalid=0 send_seq=400 receive_seq=400 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998990 adj=49998914 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=15788 bytes_read=286524 bytes_retransmit=9 bytes_invalid=0 send_seq=1823 receive_seq=1823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000179 adj=63997811 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11664 bytes_read=49588 bytes_retransmit=9 bytes_invalid=0 send_seq=1143 receive_seq=1143 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000000 adj=63997656 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2731 bytes_read=75664 bytes_retransmit=9 bytes_invalid=0 send_seq=406 receive_seq=406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999496 adj=47997714 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3325 bytes_read=9800 bytes_retransmit=9 bytes_invalid=0 send_seq=401 receive_seq=401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.8 EBB42_Gen2_v1.0_T1: temp=28.0 raspberry_pi: temp=22.9  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46401 bytes_read=320611 bytes_retransmit=0 bytes_invalid=0 send_seq=4038 receive_seq=4038 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999883 adj=31998694 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=42.5 th1: temp=41.0 th2: temp=42.2 th3: temp=40.5 sysload=0.42 cputime=41.711 memavail=7406296 print_time=340.568 buffer_time=2.016 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 317.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2308511 bytes_read=383936 bytes_retransmit=9 bytes_invalid=0 send_seq=45354 receive_seq=45354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=39964 freq=400015411 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2578 bytes_read=9974 bytes_retransmit=0 bytes_invalid=0 send_seq=401 receive_seq=401 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999024 adj=49999322 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=15864 bytes_read=289640 bytes_retransmit=9 bytes_invalid=0 send_seq=1834 receive_seq=1834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000179 adj=63997823 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=11670 bytes_read=49702 bytes_retransmit=9 bytes_invalid=0 send_seq=1144 receive_seq=1144 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999999 adj=63997648 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2737 bytes_read=75898 bytes_retransmit=9 bytes_invalid=0 send_seq=407 receive_seq=407 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999496 adj=47997729 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3331 bytes_read=9827 bytes_retransmit=9 bytes_invalid=0 send_seq=402 receive_seq=402 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.8 EBB42_Gen2_v1.0_T1: temp=28.0 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46407 bytes_read=320967 bytes_retransmit=0 bytes_invalid=0 send_seq=4039 receive_seq=4039 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998689 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.011 th0: temp=42.3 th1: temp=41.2 th2: temp=42.4 th3: temp=40.7 sysload=0.42 cputime=41.857 memavail=7406296 print_time=341.644 buffer_time=2.092 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 318.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2334318 bytes_read=386381 bytes_retransmit=9 bytes_invalid=0 send_seq=45778 receive_seq=45778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=40892 freq=400015390 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2584 bytes_read=10003 bytes_retransmit=0 bytes_invalid=0 send_seq=402 receive_seq=402 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999061 adj=49999495 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=15940 bytes_read=292697 bytes_retransmit=9 bytes_invalid=0 send_seq=1845 receive_seq=1845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000179 adj=63997841 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=11676 bytes_read=49802 bytes_retransmit=9 bytes_invalid=0 send_seq=1145 receive_seq=1145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997642 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2743 bytes_read=76162 bytes_retransmit=9 bytes_invalid=0 send_seq=408 receive_seq=408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999495 adj=47997736 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3337 bytes_read=9843 bytes_retransmit=9 bytes_invalid=0 send_seq=403 receive_seq=403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.6 EBB42_Gen2_v1.0_T1: temp=28.0 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46413 bytes_read=321323 bytes_retransmit=0 bytes_invalid=0 send_seq=4040 receive_seq=4040 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998688 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.011 th0: temp=42.3 th1: temp=41.3 th2: temp=42.1 th3: temp=40.8 sysload=0.42 cputime=42.007 memavail=7406324 print_time=342.720 buffer_time=2.167 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 319.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2359155 bytes_read=388726 bytes_retransmit=9 bytes_invalid=0 send_seq=46185 receive_seq=46185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=42748 freq=400015386 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2590 bytes_read=10019 bytes_retransmit=0 bytes_invalid=0 send_seq=403 receive_seq=403 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999093 adj=49999410 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=16016 bytes_read=295782 bytes_retransmit=9 bytes_invalid=0 send_seq=1856 receive_seq=1856 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997849 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=11682 bytes_read=49930 bytes_retransmit=9 bytes_invalid=0 send_seq=1146 receive_seq=1146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997646 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2749 bytes_read=76441 bytes_retransmit=9 bytes_invalid=0 send_seq=409 receive_seq=409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999495 adj=47997744 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3343 bytes_read=9859 bytes_retransmit=9 bytes_invalid=0 send_seq=404 receive_seq=404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999472 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.8 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46419 bytes_read=321679 bytes_retransmit=0 bytes_invalid=0 send_seq=4041 receive_seq=4041 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998694 coil_temp=17.6 refs=0 mcu_temp=20.76 supply_voltage=3.011 th0: temp=42.8 th1: temp=41.4 th2: temp=42.3 th3: temp=40.6 sysload=0.42 cputime=42.157 memavail=7406324 print_time=343.797 buffer_time=2.243 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 320.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2383939 bytes_read=391091 bytes_retransmit=9 bytes_invalid=0 send_seq=46590 receive_seq=46590 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=44604 freq=400015384 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2596 bytes_read=10035 bytes_retransmit=0 bytes_invalid=0 send_seq=404 receive_seq=404 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999126 adj=49999294 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=16092 bytes_read=298856 bytes_retransmit=9 bytes_invalid=0 send_seq=1867 receive_seq=1867 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000177 adj=63997813 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=11688 bytes_read=50030 bytes_retransmit=9 bytes_invalid=0 send_seq=1147 receive_seq=1147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999996 adj=63997616 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2755 bytes_read=76675 bytes_retransmit=9 bytes_invalid=0 send_seq=410 receive_seq=410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999496 adj=47997726 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3349 bytes_read=9875 bytes_retransmit=9 bytes_invalid=0 send_seq=405 receive_seq=405 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.7 EBB42_Gen2_v1.0_T1: temp=28.0 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46425 bytes_read=322035 bytes_retransmit=0 bytes_invalid=0 send_seq=4042 receive_seq=4042 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998687 coil_temp=17.6 refs=0 mcu_temp=20.76 supply_voltage=3.011 th0: temp=42.4 th1: temp=41.5 th2: temp=42.4 th3: temp=40.6 sysload=0.42 cputime=42.318 memavail=7401576 print_time=344.873 buffer_time=2.319 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 321.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2408640 bytes_read=393397 bytes_retransmit=9 bytes_invalid=0 send_seq=46987 receive_seq=46987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=46460 freq=400015394 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2602 bytes_read=10051 bytes_retransmit=0 bytes_invalid=0 send_seq=405 receive_seq=405 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999161 adj=49999209 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=16168 bytes_read=301915 bytes_retransmit=9 bytes_invalid=0 send_seq=1878 receive_seq=1878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000177 adj=63997786 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=11694 bytes_read=50130 bytes_retransmit=9 bytes_invalid=0 send_seq=1148 receive_seq=1148 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997595 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2761 bytes_read=76924 bytes_retransmit=9 bytes_invalid=0 send_seq=411 receive_seq=411 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999496 adj=47997719 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3355 bytes_read=9891 bytes_retransmit=9 bytes_invalid=0 send_seq=406 receive_seq=406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999902 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.0 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46431 bytes_read=322391 bytes_retransmit=0 bytes_invalid=0 send_seq=4043 receive_seq=4043 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998685 coil_temp=17.6 refs=0 mcu_temp=20.76 supply_voltage=3.011 th0: temp=42.4 th1: temp=41.5 th2: temp=42.2 th3: temp=40.8 sysload=0.39 cputime=42.467 memavail=7407972 print_time=345.950 buffer_time=2.395 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 322.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2433439 bytes_read=395745 bytes_retransmit=9 bytes_invalid=0 send_seq=47395 receive_seq=47395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=48316 freq=400015377 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2608 bytes_read=10067 bytes_retransmit=0 bytes_invalid=0 send_seq=406 receive_seq=406 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999194 adj=49999164 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=16244 bytes_read=305000 bytes_retransmit=9 bytes_invalid=0 send_seq=1889 receive_seq=1889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000176 adj=63997750 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11700 bytes_read=50272 bytes_retransmit=9 bytes_invalid=0 send_seq=1149 receive_seq=1149 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2767 bytes_read=77203 bytes_retransmit=9 bytes_invalid=0 send_seq=412 receive_seq=412 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999496 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3361 bytes_read=9918 bytes_retransmit=9 bytes_invalid=0 send_seq=407 receive_seq=407 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999903 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.0 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46437 bytes_read=322747 bytes_retransmit=0 bytes_invalid=0 send_seq=4044 receive_seq=4044 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998669 coil_temp=17.6 refs=0 mcu_temp=20.75 supply_voltage=3.012 th0: temp=42.7 th1: temp=41.3 th2: temp=42.3 th3: temp=40.6 sysload=0.39 cputime=42.611 memavail=7407972 print_time=347.026 buffer_time=2.471 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 323.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2458266 bytes_read=398114 bytes_retransmit=9 bytes_invalid=0 send_seq=47804 receive_seq=47804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=37943 freq=400015372 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2614 bytes_read=10096 bytes_retransmit=0 bytes_invalid=0 send_seq=407 receive_seq=407 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999226 adj=49999151 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=16320 bytes_read=308056 bytes_retransmit=9 bytes_invalid=0 send_seq=1900 receive_seq=1900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000176 adj=63997766 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11706 bytes_read=50372 bytes_retransmit=9 bytes_invalid=0 send_seq=1150 receive_seq=1150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997575 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2773 bytes_read=77452 bytes_retransmit=9 bytes_invalid=0 send_seq=413 receive_seq=413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999497 adj=47997706 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3367 bytes_read=9934 bytes_retransmit=9 bytes_invalid=0 send_seq=408 receive_seq=408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999904 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.0 EBB42_Gen2_v1.0_T1: temp=28.0 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46443 bytes_read=323103 bytes_retransmit=0 bytes_invalid=0 send_seq=4045 receive_seq=4045 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999881 adj=31998676 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=42.5 th1: temp=41.2 th2: temp=42.6 th3: temp=40.6 sysload=0.39 cputime=42.747 memavail=7407984 print_time=347.565 buffer_time=2.009 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 324.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2483117 bytes_read=400469 bytes_retransmit=9 bytes_invalid=0 send_seq=48211 receive_seq=48210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=39765 freq=400015372 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2620 bytes_read=10112 bytes_retransmit=0 bytes_invalid=0 send_seq=408 receive_seq=408 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49999536 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=16396 bytes_read=311172 bytes_retransmit=9 bytes_invalid=0 send_seq=1911 receive_seq=1911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000176 adj=63997779 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11712 bytes_read=50472 bytes_retransmit=9 bytes_invalid=0 send_seq=1151 receive_seq=1151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997580 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2779 bytes_read=77701 bytes_retransmit=9 bytes_invalid=0 send_seq=414 receive_seq=414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999497 adj=47997723 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3373 bytes_read=9950 bytes_retransmit=9 bytes_invalid=0 send_seq=409 receive_seq=409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999904 adj=11999473 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=28.8 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46449 bytes_read=323459 bytes_retransmit=0 bytes_invalid=0 send_seq=4046 receive_seq=4046 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999881 adj=31998676 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=41.8 th1: temp=41.4 th2: temp=42.5 th3: temp=40.8 sysload=0.39 cputime=42.896 memavail=7407984 print_time=348.641 buffer_time=2.085 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 325.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2508825 bytes_read=402895 bytes_retransmit=9 bytes_invalid=0 send_seq=48630 receive_seq=48630 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=40727 freq=400015375 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2626 bytes_read=10128 bytes_retransmit=0 bytes_invalid=0 send_seq=409 receive_seq=409 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999291 adj=49999660 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=16465 bytes_read=314252 bytes_retransmit=9 bytes_invalid=0 send_seq=1921 receive_seq=1921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000176 adj=63997762 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11718 bytes_read=50600 bytes_retransmit=9 bytes_invalid=0 send_seq=1152 receive_seq=1152 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999996 adj=63997603 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2785 bytes_read=77980 bytes_retransmit=9 bytes_invalid=0 send_seq=415 receive_seq=415 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999497 adj=47997713 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3379 bytes_read=9966 bytes_retransmit=9 bytes_invalid=0 send_seq=410 receive_seq=410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999904 adj=11999471 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.8 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46455 bytes_read=323815 bytes_retransmit=0 bytes_invalid=0 send_seq=4047 receive_seq=4047 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999880 adj=31998667 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=42.6 th1: temp=41.5 th2: temp=42.3 th3: temp=40.6 sysload=0.39 cputime=43.051 memavail=7407228 print_time=349.718 buffer_time=2.161 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 326.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2533641 bytes_read=405274 bytes_retransmit=9 bytes_invalid=0 send_seq=49038 receive_seq=49038 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=42583 freq=400015377 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2632 bytes_read=10144 bytes_retransmit=0 bytes_invalid=0 send_seq=410 receive_seq=410 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999321 adj=49999507 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=16541 bytes_read=317308 bytes_retransmit=9 bytes_invalid=0 send_seq=1932 receive_seq=1932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997746 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11724 bytes_read=50700 bytes_retransmit=9 bytes_invalid=0 send_seq=1153 receive_seq=1153 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999996 adj=63997576 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2791 bytes_read=78214 bytes_retransmit=9 bytes_invalid=0 send_seq=416 receive_seq=416 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999496 adj=47997694 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3385 bytes_read=9982 bytes_retransmit=9 bytes_invalid=0 send_seq=411 receive_seq=411 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999903 adj=11999462 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.8 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46461 bytes_read=324189 bytes_retransmit=0 bytes_invalid=0 send_seq=4048 receive_seq=4048 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999880 adj=31998655 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=42.4 th1: temp=41.1 th2: temp=42.4 th3: temp=40.8 sysload=0.36 cputime=43.204 memavail=7407228 print_time=350.794 buffer_time=2.236 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 327.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2558408 bytes_read=407609 bytes_retransmit=9 bytes_invalid=0 send_seq=49443 receive_seq=49443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=44439 freq=400015387 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2638 bytes_read=10160 bytes_retransmit=0 bytes_invalid=0 send_seq=411 receive_seq=411 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999355 adj=49999387 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=16617 bytes_read=320365 bytes_retransmit=9 bytes_invalid=0 send_seq=1943 receive_seq=1943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000174 adj=63997727 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11730 bytes_read=50814 bytes_retransmit=9 bytes_invalid=0 send_seq=1154 receive_seq=1154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2797 bytes_read=78463 bytes_retransmit=9 bytes_invalid=0 send_seq=417 receive_seq=417 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999496 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3391 bytes_read=10009 bytes_retransmit=9 bytes_invalid=0 send_seq=412 receive_seq=412 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999904 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.0 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46467 bytes_read=324545 bytes_retransmit=0 bytes_invalid=0 send_seq=4049 receive_seq=4049 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999881 adj=31998648 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=42.5 th1: temp=41.5 th2: temp=42.4 th3: temp=40.7 sysload=0.36 cputime=43.351 memavail=7407228 print_time=351.870 buffer_time=2.312 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 328.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2583197 bytes_read=409949 bytes_retransmit=9 bytes_invalid=0 send_seq=49849 receive_seq=49849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=46295 freq=400015390 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2644 bytes_read=10189 bytes_retransmit=0 bytes_invalid=0 send_seq=412 receive_seq=412 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999385 adj=49999331 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=16693 bytes_read=323449 bytes_retransmit=9 bytes_invalid=0 send_seq=1954 receive_seq=1954 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000174 adj=63997698 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11736 bytes_read=50942 bytes_retransmit=9 bytes_invalid=0 send_seq=1155 receive_seq=1155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2803 bytes_read=78757 bytes_retransmit=9 bytes_invalid=0 send_seq=418 receive_seq=418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999496 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3397 bytes_read=10025 bytes_retransmit=9 bytes_invalid=0 send_seq=413 receive_seq=413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999904 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.9 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46473 bytes_read=324901 bytes_retransmit=0 bytes_invalid=0 send_seq=4050 receive_seq=4050 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999880 adj=31998648 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=42.5 th1: temp=41.5 th2: temp=42.4 th3: temp=40.8 sysload=0.36 cputime=43.502 memavail=7407228 print_time=352.947 buffer_time=2.388 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 329.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2607991 bytes_read=412323 bytes_retransmit=9 bytes_invalid=0 send_seq=50256 receive_seq=50256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=48151 freq=400015390 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2650 bytes_read=10205 bytes_retransmit=0 bytes_invalid=0 send_seq=413 receive_seq=413 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999415 adj=49999261 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=16769 bytes_read=326508 bytes_retransmit=9 bytes_invalid=0 send_seq=1965 receive_seq=1965 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000174 adj=63997697 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11742 bytes_read=51042 bytes_retransmit=9 bytes_invalid=0 send_seq=1156 receive_seq=1156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999994 adj=63997518 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2809 bytes_read=78991 bytes_retransmit=9 bytes_invalid=0 send_seq=419 receive_seq=419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999497 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3403 bytes_read=10041 bytes_retransmit=9 bytes_invalid=0 send_seq=414 receive_seq=414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999904 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.0 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46479 bytes_read=325257 bytes_retransmit=0 bytes_invalid=0 send_seq=4051 receive_seq=4051 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999881 adj=31998639 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=42.4 th1: temp=41.7 th2: temp=42.5 th3: temp=40.7 sysload=0.36 cputime=43.648 memavail=7407228 print_time=354.023 buffer_time=2.464 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 330.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2632897 bytes_read=414699 bytes_retransmit=9 bytes_invalid=0 send_seq=50666 receive_seq=50666 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=37742 freq=400015383 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2656 bytes_read=10221 bytes_retransmit=0 bytes_invalid=0 send_seq=414 receive_seq=414 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999444 adj=49999219 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=16845 bytes_read=329582 bytes_retransmit=9 bytes_invalid=0 send_seq=1976 receive_seq=1976 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000173 adj=63997693 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11748 bytes_read=51142 bytes_retransmit=9 bytes_invalid=0 send_seq=1157 receive_seq=1157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997516 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2815 bytes_read=79240 bytes_retransmit=9 bytes_invalid=0 send_seq=420 receive_seq=420 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999496 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3409 bytes_read=10057 bytes_retransmit=9 bytes_invalid=0 send_seq=415 receive_seq=415 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999904 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.8 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46485 bytes_read=325613 bytes_retransmit=0 bytes_invalid=0 send_seq=4052 receive_seq=4052 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999881 adj=31998647 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=42.6 th1: temp=41.4 th2: temp=42.8 th3: temp=41.0 sysload=0.36 cputime=43.785 memavail=7407228 print_time=354.562 buffer_time=2.002 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 331.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2657681 bytes_read=417034 bytes_retransmit=9 bytes_invalid=0 send_seq=51071 receive_seq=51071 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=39598 freq=400015385 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2662 bytes_read=10237 bytes_retransmit=0 bytes_invalid=0 send_seq=415 receive_seq=415 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999471 adj=49999562 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=16921 bytes_read=332669 bytes_retransmit=9 bytes_invalid=0 send_seq=1987 receive_seq=1987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000174 adj=63997700 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11754 bytes_read=51270 bytes_retransmit=9 bytes_invalid=0 send_seq=1158 receive_seq=1158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999994 adj=63997535 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2821 bytes_read=79519 bytes_retransmit=9 bytes_invalid=0 send_seq=421 receive_seq=421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999498 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3415 bytes_read=10073 bytes_retransmit=9 bytes_invalid=0 send_seq=416 receive_seq=416 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999904 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.9 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46491 bytes_read=325969 bytes_retransmit=0 bytes_invalid=0 send_seq=4053 receive_seq=4053 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999881 adj=31998657 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=42.7 th1: temp=41.6 th2: temp=42.4 th3: temp=40.7 sysload=0.33 cputime=43.935 memavail=7407228 print_time=355.638 buffer_time=2.078 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 332.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2683416 bytes_read=419474 bytes_retransmit=9 bytes_invalid=0 send_seq=51492 receive_seq=51492 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=40563 freq=400015378 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2668 bytes_read=10253 bytes_retransmit=0 bytes_invalid=0 send_seq=416 receive_seq=416 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999498 adj=49999652 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=16997 bytes_read=335783 bytes_retransmit=9 bytes_invalid=0 send_seq=1998 receive_seq=1998 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997710 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11760 bytes_read=51384 bytes_retransmit=9 bytes_invalid=0 send_seq=1159 receive_seq=1159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999993 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2827 bytes_read=79753 bytes_retransmit=9 bytes_invalid=0 send_seq=422 receive_seq=422 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999498 adj=47997679 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3421 bytes_read=10100 bytes_retransmit=9 bytes_invalid=0 send_seq=417 receive_seq=417 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999904 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=28.9 EBB42_Gen2_v1.0_T1: temp=28.0 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46497 bytes_read=326325 bytes_retransmit=0 bytes_invalid=0 send_seq=4054 receive_seq=4054 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998652 coil_temp=17.6 refs=0 mcu_temp=20.75 supply_voltage=3.012 th0: temp=42.4 th1: temp=41.6 th2: temp=42.8 th3: temp=40.8 sysload=0.33 cputime=44.083 memavail=7407228 print_time=356.715 buffer_time=2.154 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 333.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2708220 bytes_read=421829 bytes_retransmit=9 bytes_invalid=0 send_seq=51901 receive_seq=51901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=42419 freq=400015374 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2674 bytes_read=10282 bytes_retransmit=0 bytes_invalid=0 send_seq=417 receive_seq=417 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999524 adj=49999499 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=17073 bytes_read=338839 bytes_retransmit=9 bytes_invalid=0 send_seq=2009 receive_seq=2009 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000174 adj=63997734 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11766 bytes_read=51484 bytes_retransmit=9 bytes_invalid=0 send_seq=1160 receive_seq=1160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2833 bytes_read=80017 bytes_retransmit=9 bytes_invalid=0 send_seq=423 receive_seq=423 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999498 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3427 bytes_read=10116 bytes_retransmit=9 bytes_invalid=0 send_seq=418 receive_seq=418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999904 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.0 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46503 bytes_read=326681 bytes_retransmit=0 bytes_invalid=0 send_seq=4055 receive_seq=4055 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998673 coil_temp=17.6 refs=0 mcu_temp=20.75 supply_voltage=3.012 th0: temp=42.7 th1: temp=41.0 th2: temp=42.9 th3: temp=40.9 sysload=0.33 cputime=44.233 memavail=7407228 print_time=357.791 buffer_time=2.231 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 334.1: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2733014 bytes_read=424174 bytes_retransmit=9 bytes_invalid=0 send_seq=52308 receive_seq=52308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=44305 freq=400015367 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2680 bytes_read=10298 bytes_retransmit=0 bytes_invalid=0 send_seq=418 receive_seq=418 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999549 adj=49999385 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=17149 bytes_read=341924 bytes_retransmit=9 bytes_invalid=0 send_seq=2020 receive_seq=2020 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997729 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11772 bytes_read=51612 bytes_retransmit=9 bytes_invalid=0 send_seq=1161 receive_seq=1161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997561 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2839 bytes_read=80281 bytes_retransmit=9 bytes_invalid=0 send_seq=424 receive_seq=424 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999505 adj=47997683 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3433 bytes_read=10132 bytes_retransmit=9 bytes_invalid=0 send_seq=419 receive_seq=419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999904 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.8 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46509 bytes_read=327037 bytes_retransmit=0 bytes_invalid=0 send_seq=4056 receive_seq=4056 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998667 coil_temp=17.6 refs=0 mcu_temp=20.75 supply_voltage=3.012 th0: temp=42.8 th1: temp=41.6 th2: temp=42.5 th3: temp=40.8 sysload=0.33 cputime=44.384 memavail=7407228 print_time=358.867 buffer_time=2.307 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 335.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2757808 bytes_read=426564 bytes_retransmit=9 bytes_invalid=0 send_seq=52715 receive_seq=52715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=46161 freq=400015354 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2686 bytes_read=10314 bytes_retransmit=0 bytes_invalid=0 send_seq=419 receive_seq=419 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999576 adj=49999295 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=17225 bytes_read=344997 bytes_retransmit=9 bytes_invalid=0 send_seq=2031 receive_seq=2031 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997747 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11778 bytes_read=51712 bytes_retransmit=9 bytes_invalid=0 send_seq=1162 receive_seq=1162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997590 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2845 bytes_read=80499 bytes_retransmit=9 bytes_invalid=0 send_seq=425 receive_seq=425 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999505 adj=47997767 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3439 bytes_read=10148 bytes_retransmit=9 bytes_invalid=0 send_seq=420 receive_seq=420 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=28.9 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46515 bytes_read=327393 bytes_retransmit=0 bytes_invalid=0 send_seq=4057 receive_seq=4057 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999881 adj=31998675 coil_temp=17.6 refs=0 mcu_temp=20.75 supply_voltage=3.012 th0: temp=43.1 th1: temp=41.5 th2: temp=42.6 th3: temp=40.8 sysload=0.33 cputime=44.538 memavail=7408656 print_time=359.944 buffer_time=2.383 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 336.1: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2782582 bytes_read=428889 bytes_retransmit=9 bytes_invalid=0 send_seq=53118 receive_seq=53118 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=48017 freq=400015340 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2692 bytes_read=10330 bytes_retransmit=0 bytes_invalid=0 send_seq=420 receive_seq=420 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999601 adj=49999261 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=17294 bytes_read=348031 bytes_retransmit=9 bytes_invalid=0 send_seq=2041 receive_seq=2041 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997763 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11784 bytes_read=51812 bytes_retransmit=9 bytes_invalid=0 send_seq=1163 receive_seq=1163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000000 adj=63997613 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2851 bytes_read=80731 bytes_retransmit=9 bytes_invalid=0 send_seq=426 receive_seq=426 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999506 adj=47997763 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3445 bytes_read=10164 bytes_retransmit=9 bytes_invalid=0 send_seq=421 receive_seq=421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999480 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.1 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46521 bytes_read=327749 bytes_retransmit=0 bytes_invalid=0 send_seq=4058 receive_seq=4058 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999881 adj=31998675 coil_temp=17.6 refs=0 mcu_temp=20.75 supply_voltage=3.012 th0: temp=42.6 th1: temp=41.6 th2: temp=42.9 th3: temp=41.1 sysload=0.30 cputime=44.680 memavail=7408656 print_time=361.020 buffer_time=2.459 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 337.2: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2807795 bytes_read=431284 bytes_retransmit=9 bytes_invalid=0 send_seq=53535 receive_seq=53535 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=49463 freq=400015342 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2698 bytes_read=10346 bytes_retransmit=0 bytes_invalid=0 send_seq=421 receive_seq=421 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999625 adj=49999221 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=17370 bytes_read=351173 bytes_retransmit=9 bytes_invalid=0 send_seq=2052 receive_seq=2052 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000174 adj=63997775 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11790 bytes_read=51954 bytes_retransmit=9 bytes_invalid=0 send_seq=1164 receive_seq=1164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999999 adj=63997641 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2857 bytes_read=80991 bytes_retransmit=9 bytes_invalid=0 send_seq=427 receive_seq=427 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999505 adj=47997768 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3451 bytes_read=10191 bytes_retransmit=9 bytes_invalid=0 send_seq=422 receive_seq=422 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999475 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.0 EBB42_Gen2_v1.0_T1: temp=28.0 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46527 bytes_read=328105 bytes_retransmit=0 bytes_invalid=0 send_seq=4059 receive_seq=4059 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999881 adj=31998681 coil_temp=17.6 refs=0 mcu_temp=20.76 supply_voltage=3.012 th0: temp=42.4 th1: temp=41.4 th2: temp=42.7 th3: temp=41.0 sysload=0.30 cputime=44.832 memavail=7405124 print_time=362.097 buffer_time=2.521 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 338.2: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2832504 bytes_read=433648 bytes_retransmit=9 bytes_invalid=0 send_seq=53940 receive_seq=53940 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=39171 freq=400015352 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2704 bytes_read=10375 bytes_retransmit=0 bytes_invalid=0 send_seq=422 receive_seq=422 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999648 adj=49999177 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=17446 bytes_read=354230 bytes_retransmit=9 bytes_invalid=0 send_seq=2063 receive_seq=2063 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997758 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11796 bytes_read=52054 bytes_retransmit=9 bytes_invalid=0 send_seq=1165 receive_seq=1165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997609 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2863 bytes_read=81224 bytes_retransmit=9 bytes_invalid=0 send_seq=428 receive_seq=428 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999505 adj=47997741 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3457 bytes_read=10207 bytes_retransmit=9 bytes_invalid=0 send_seq=423 receive_seq=423 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999467 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.1 EBB42_Gen2_v1.0_T1: temp=28.0 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46533 bytes_read=328461 bytes_retransmit=0 bytes_invalid=0 send_seq=4060 receive_seq=4060 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999881 adj=31998668 coil_temp=17.6 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=42.7 th1: temp=41.5 th2: temp=42.3 th3: temp=41.0 sysload=0.30 cputime=44.972 memavail=7409268 print_time=362.635 buffer_time=2.059 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 339.2: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2857944 bytes_read=436043 bytes_retransmit=9 bytes_invalid=0 send_seq=54357 receive_seq=54357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400015359 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2710 bytes_read=10391 bytes_retransmit=0 bytes_invalid=0 send_seq=423 receive_seq=423 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999670 adj=49999430 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=17522 bytes_read=357290 bytes_retransmit=9 bytes_invalid=0 send_seq=2074 receive_seq=2074 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997743 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11802 bytes_read=52154 bytes_retransmit=9 bytes_invalid=0 send_seq=1166 receive_seq=1166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997577 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2869 bytes_read=81487 bytes_retransmit=9 bytes_invalid=0 send_seq=429 receive_seq=429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999504 adj=47997720 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3463 bytes_read=10223 bytes_retransmit=9 bytes_invalid=0 send_seq=424 receive_seq=424 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.0 EBB42_Gen2_v1.0_T1: temp=28.0 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46539 bytes_read=328817 bytes_retransmit=0 bytes_invalid=0 send_seq=4061 receive_seq=4061 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998662 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=42.8 th1: temp=41.8 th2: temp=42.7 th3: temp=40.9 sysload=0.30 cputime=45.119 memavail=7411012 print_time=363.712 buffer_time=2.135 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 340.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2883128 bytes_read=438444 bytes_retransmit=9 bytes_invalid=0 send_seq=54772 receive_seq=54772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=41955 freq=400015371 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2716 bytes_read=10407 bytes_retransmit=0 bytes_invalid=0 send_seq=424 receive_seq=424 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999691 adj=49999485 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=17598 bytes_read=360392 bytes_retransmit=9 bytes_invalid=0 send_seq=2085 receive_seq=2085 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000176 adj=63997734 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11808 bytes_read=52282 bytes_retransmit=9 bytes_invalid=0 send_seq=1167 receive_seq=1167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999996 adj=63997549 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2875 bytes_read=81736 bytes_retransmit=9 bytes_invalid=0 send_seq=430 receive_seq=430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999505 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3469 bytes_read=10239 bytes_retransmit=9 bytes_invalid=0 send_seq=425 receive_seq=425 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.0 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46545 bytes_read=329173 bytes_retransmit=0 bytes_invalid=0 send_seq=4062 receive_seq=4062 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999881 adj=31998664 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=42.5 th1: temp=41.7 th2: temp=42.6 th3: temp=41.0 sysload=0.30 cputime=45.268 memavail=7410760 print_time=364.788 buffer_time=2.211 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 341.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2907932 bytes_read=440828 bytes_retransmit=9 bytes_invalid=0 send_seq=55181 receive_seq=55181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=43811 freq=400015364 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2722 bytes_read=10423 bytes_retransmit=0 bytes_invalid=0 send_seq=425 receive_seq=425 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999713 adj=49999326 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=17674 bytes_read=363451 bytes_retransmit=9 bytes_invalid=0 send_seq=2096 receive_seq=2096 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000177 adj=63997714 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11814 bytes_read=52382 bytes_retransmit=9 bytes_invalid=0 send_seq=1168 receive_seq=1168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999996 adj=63997516 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2881 bytes_read=81970 bytes_retransmit=9 bytes_invalid=0 send_seq=431 receive_seq=431 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999505 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3475 bytes_read=10255 bytes_retransmit=9 bytes_invalid=0 send_seq=426 receive_seq=426 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.0 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46551 bytes_read=329529 bytes_retransmit=0 bytes_invalid=0 send_seq=4063 receive_seq=4063 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999881 adj=31998645 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=42.8 th1: temp=41.5 th2: temp=42.9 th3: temp=41.1 sysload=0.28 cputime=45.422 memavail=7410760 print_time=365.865 buffer_time=2.288 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 342.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2932731 bytes_read=443178 bytes_retransmit=9 bytes_invalid=0 send_seq=55589 receive_seq=55589 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=45667 freq=400015360 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2728 bytes_read=10439 bytes_retransmit=0 bytes_invalid=0 send_seq=426 receive_seq=426 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999734 adj=49999247 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=17750 bytes_read=366507 bytes_retransmit=9 bytes_invalid=0 send_seq=2107 receive_seq=2107 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000177 adj=63997746 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11820 bytes_read=52496 bytes_retransmit=9 bytes_invalid=0 send_seq=1169 receive_seq=1169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999996 adj=63997536 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2887 bytes_read=82249 bytes_retransmit=9 bytes_invalid=0 send_seq=432 receive_seq=432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999505 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3481 bytes_read=10282 bytes_retransmit=9 bytes_invalid=0 send_seq=427 receive_seq=427 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=28.9 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46557 bytes_read=329885 bytes_retransmit=0 bytes_invalid=0 send_seq=4064 receive_seq=4064 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998651 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=42.7 th1: temp=41.6 th2: temp=42.9 th3: temp=40.9 sysload=0.28 cputime=45.575 memavail=7410760 print_time=366.941 buffer_time=2.363 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 343.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2957520 bytes_read=445514 bytes_retransmit=9 bytes_invalid=0 send_seq=55995 receive_seq=55995 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=47523 freq=400015349 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2734 bytes_read=10468 bytes_retransmit=0 bytes_invalid=0 send_seq=427 receive_seq=427 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999754 adj=49999177 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=17826 bytes_read=369649 bytes_retransmit=9 bytes_invalid=0 send_seq=2118 receive_seq=2118 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997739 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11826 bytes_read=52624 bytes_retransmit=9 bytes_invalid=0 send_seq=1170 receive_seq=1170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997544 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2893 bytes_read=82513 bytes_retransmit=9 bytes_invalid=0 send_seq=433 receive_seq=433 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999504 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3487 bytes_read=10298 bytes_retransmit=9 bytes_invalid=0 send_seq=428 receive_seq=428 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.1 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46563 bytes_read=330241 bytes_retransmit=0 bytes_invalid=0 send_seq=4065 receive_seq=4065 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998666 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.1 th1: temp=41.6 th2: temp=42.7 th3: temp=40.8 sysload=0.28 cputime=45.719 memavail=7410760 print_time=368.017 buffer_time=2.439 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 344.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=2982345 bytes_read=447898 bytes_retransmit=9 bytes_invalid=0 send_seq=56404 receive_seq=56404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=49364 freq=400015378 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2740 bytes_read=10484 bytes_retransmit=0 bytes_invalid=0 send_seq=428 receive_seq=428 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999775 adj=49999135 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=17902 bytes_read=372706 bytes_retransmit=9 bytes_invalid=0 send_seq=2129 receive_seq=2129 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997929 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11832 bytes_read=52724 bytes_retransmit=9 bytes_invalid=0 send_seq=1171 receive_seq=1171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997553 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2899 bytes_read=82747 bytes_retransmit=9 bytes_invalid=0 send_seq=434 receive_seq=434 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999504 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3493 bytes_read=10314 bytes_retransmit=9 bytes_invalid=0 send_seq=429 receive_seq=429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.0 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46569 bytes_read=330597 bytes_retransmit=0 bytes_invalid=0 send_seq=4066 receive_seq=4066 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999883 adj=31998672 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=42.9 th1: temp=41.4 th2: temp=42.5 th3: temp=41.0 sysload=0.28 cputime=45.870 memavail=7410760 print_time=369.094 buffer_time=2.515 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 345.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3007134 bytes_read=450254 bytes_retransmit=9 bytes_invalid=0 send_seq=56810 receive_seq=56810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=39004 freq=400015364 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2746 bytes_read=10500 bytes_retransmit=0 bytes_invalid=0 send_seq=429 receive_seq=429 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999793 adj=49999057 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=17978 bytes_read=375794 bytes_retransmit=9 bytes_invalid=0 send_seq=2140 receive_seq=2140 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997826 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11838 bytes_read=52838 bytes_retransmit=9 bytes_invalid=0 send_seq=1172 receive_seq=1172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997493 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2905 bytes_read=83026 bytes_retransmit=9 bytes_invalid=0 send_seq=435 receive_seq=435 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999503 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3499 bytes_read=10330 bytes_retransmit=9 bytes_invalid=0 send_seq=430 receive_seq=430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.0 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46575 bytes_read=330953 bytes_retransmit=0 bytes_invalid=0 send_seq=4067 receive_seq=4067 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998654 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=42.8 th1: temp=41.8 th2: temp=42.7 th3: temp=41.0 sysload=0.28 cputime=46.007 memavail=7409780 print_time=369.632 buffer_time=2.052 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 346.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3032378 bytes_read=452644 bytes_retransmit=9 bytes_invalid=0 send_seq=57226 receive_seq=57226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400015355 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2752 bytes_read=10516 bytes_retransmit=0 bytes_invalid=0 send_seq=430 receive_seq=430 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999811 adj=49999290 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=18054 bytes_read=378866 bytes_retransmit=9 bytes_invalid=0 send_seq=2151 receive_seq=2151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997832 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11844 bytes_read=52952 bytes_retransmit=9 bytes_invalid=0 send_seq=1173 receive_seq=1173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999994 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2911 bytes_read=83275 bytes_retransmit=9 bytes_invalid=0 send_seq=436 receive_seq=436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999503 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3505 bytes_read=10346 bytes_retransmit=9 bytes_invalid=0 send_seq=431 receive_seq=431 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999904 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.1 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46581 bytes_read=331309 bytes_retransmit=0 bytes_invalid=0 send_seq=4068 receive_seq=4068 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998660 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=42.8 th1: temp=41.8 th2: temp=42.8 th3: temp=40.9 sysload=0.26 cputime=46.158 memavail=7409780 print_time=370.709 buffer_time=2.128 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 347.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3057819 bytes_read=455083 bytes_retransmit=9 bytes_invalid=0 send_seq=57646 receive_seq=57646 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=41753 freq=400015354 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2758 bytes_read=10532 bytes_retransmit=0 bytes_invalid=0 send_seq=431 receive_seq=431 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999829 adj=49999348 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=18130 bytes_read=381922 bytes_retransmit=9 bytes_invalid=0 send_seq=2162 receive_seq=2162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997820 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=11850 bytes_read=53066 bytes_retransmit=9 bytes_invalid=0 send_seq=1174 receive_seq=1174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999994 adj=63997536 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2917 bytes_read=83509 bytes_retransmit=9 bytes_invalid=0 send_seq=437 receive_seq=437 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999503 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3511 bytes_read=10373 bytes_retransmit=9 bytes_invalid=0 send_seq=432 receive_seq=432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.1 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46587 bytes_read=331665 bytes_retransmit=0 bytes_invalid=0 send_seq=4069 receive_seq=4069 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998659 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.011 th0: temp=43.1 th1: temp=42.1 th2: temp=42.6 th3: temp=41.1 sysload=0.26 cputime=46.311 memavail=7409780 print_time=371.785 buffer_time=2.204 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 348.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3082618 bytes_read=457433 bytes_retransmit=9 bytes_invalid=0 send_seq=58054 receive_seq=58054 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=43609 freq=400015355 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2764 bytes_read=10561 bytes_retransmit=0 bytes_invalid=0 send_seq=432 receive_seq=432 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999846 adj=49999238 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=18206 bytes_read=384993 bytes_retransmit=9 bytes_invalid=0 send_seq=2173 receive_seq=2173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997839 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=11856 bytes_read=53180 bytes_retransmit=9 bytes_invalid=0 send_seq=1175 receive_seq=1175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999996 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2923 bytes_read=83818 bytes_retransmit=9 bytes_invalid=0 send_seq=438 receive_seq=438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999503 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3517 bytes_read=10389 bytes_retransmit=9 bytes_invalid=0 send_seq=433 receive_seq=433 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.3 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46593 bytes_read=332021 bytes_retransmit=0 bytes_invalid=0 send_seq=4070 receive_seq=4070 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999881 adj=31998664 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=42.9 th1: temp=41.8 th2: temp=42.8 th3: temp=41.4 sysload=0.26 cputime=46.465 memavail=7409780 print_time=372.862 buffer_time=2.279 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 349.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3107412 bytes_read=459778 bytes_retransmit=9 bytes_invalid=0 send_seq=58461 receive_seq=58461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=45465 freq=400015363 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2770 bytes_read=10577 bytes_retransmit=0 bytes_invalid=0 send_seq=433 receive_seq=433 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999863 adj=49999143 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=18282 bytes_read=388124 bytes_retransmit=9 bytes_invalid=0 send_seq=2184 receive_seq=2184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997798 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=11862 bytes_read=53294 bytes_retransmit=9 bytes_invalid=0 send_seq=1176 receive_seq=1176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997553 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2929 bytes_read=84052 bytes_retransmit=9 bytes_invalid=0 send_seq=439 receive_seq=439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999503 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3523 bytes_read=10405 bytes_retransmit=9 bytes_invalid=0 send_seq=434 receive_seq=434 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.0 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46599 bytes_read=332377 bytes_retransmit=0 bytes_invalid=0 send_seq=4071 receive_seq=4071 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999881 adj=31998653 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=43.0 th1: temp=41.8 th2: temp=42.8 th3: temp=41.1 sysload=0.26 cputime=46.620 memavail=7409780 print_time=373.938 buffer_time=2.355 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 350.2: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3132206 bytes_read=462168 bytes_retransmit=9 bytes_invalid=0 send_seq=58868 receive_seq=58868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=47321 freq=400015350 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2776 bytes_read=10593 bytes_retransmit=0 bytes_invalid=0 send_seq=434 receive_seq=434 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999879 adj=49999061 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=18351 bytes_read=391175 bytes_retransmit=9 bytes_invalid=0 send_seq=2194 receive_seq=2194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997756 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=11868 bytes_read=53394 bytes_retransmit=9 bytes_invalid=0 send_seq=1177 receive_seq=1177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997654 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2935 bytes_read=84286 bytes_retransmit=9 bytes_invalid=0 send_seq=440 receive_seq=440 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999502 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3529 bytes_read=10421 bytes_retransmit=9 bytes_invalid=0 send_seq=435 receive_seq=435 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.1 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46605 bytes_read=332733 bytes_retransmit=0 bytes_invalid=0 send_seq=4072 receive_seq=4072 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999881 adj=31998642 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.011 th0: temp=43.0 th1: temp=41.8 th2: temp=43.0 th3: temp=41.1 sysload=0.26 cputime=46.768 memavail=7409780 print_time=375.015 buffer_time=2.431 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 351.2: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3156947 bytes_read=464498 bytes_retransmit=9 bytes_invalid=0 send_seq=59272 receive_seq=59272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=49164 freq=400015344 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2782 bytes_read=10609 bytes_retransmit=0 bytes_invalid=0 send_seq=435 receive_seq=435 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999894 adj=49999024 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=18427 bytes_read=394246 bytes_retransmit=9 bytes_invalid=0 send_seq=2205 receive_seq=2205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997775 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=11874 bytes_read=53508 bytes_retransmit=9 bytes_invalid=0 send_seq=1178 receive_seq=1178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997639 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2941 bytes_read=84580 bytes_retransmit=9 bytes_invalid=0 send_seq=441 receive_seq=441 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999502 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3535 bytes_read=10437 bytes_retransmit=9 bytes_invalid=0 send_seq=436 receive_seq=436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46611 bytes_read=333089 bytes_retransmit=0 bytes_invalid=0 send_seq=4073 receive_seq=4073 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999883 adj=31998654 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.011 th0: temp=42.9 th1: temp=41.8 th2: temp=43.2 th3: temp=41.0 sysload=0.23 cputime=46.911 memavail=7409792 print_time=376.091 buffer_time=2.507 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 352.2: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3181686 bytes_read=466788 bytes_retransmit=9 bytes_invalid=0 send_seq=59668 receive_seq=59668 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=38804 freq=400015358 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2788 bytes_read=10625 bytes_retransmit=0 bytes_invalid=0 send_seq=436 receive_seq=436 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999908 adj=49998982 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=18503 bytes_read=397317 bytes_retransmit=9 bytes_invalid=0 send_seq=2216 receive_seq=2216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997768 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11880 bytes_read=53636 bytes_retransmit=9 bytes_invalid=0 send_seq=1179 receive_seq=1179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997618 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2947 bytes_read=84814 bytes_retransmit=9 bytes_invalid=0 send_seq=442 receive_seq=442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999503 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3541 bytes_read=10464 bytes_retransmit=9 bytes_invalid=0 send_seq=437 receive_seq=437 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.1 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46617 bytes_read=333445 bytes_retransmit=0 bytes_invalid=0 send_seq=4074 receive_seq=4074 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999883 adj=31998682 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.011 th0: temp=43.0 th1: temp=41.8 th2: temp=43.1 th3: temp=40.9 sysload=0.23 cputime=47.043 memavail=7409792 print_time=376.629 buffer_time=2.045 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 353.2: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3206716 bytes_read=469180 bytes_retransmit=9 bytes_invalid=0 send_seq=60079 receive_seq=60079 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=40461 freq=400015359 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2794 bytes_read=10653 bytes_retransmit=0 bytes_invalid=0 send_seq=437 receive_seq=437 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999924 adj=49999126 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=18579 bytes_read=400376 bytes_retransmit=9 bytes_invalid=0 send_seq=2227 receive_seq=2227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997726 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11886 bytes_read=53736 bytes_retransmit=9 bytes_invalid=0 send_seq=1180 receive_seq=1180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997587 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2953 bytes_read=85063 bytes_retransmit=9 bytes_invalid=0 send_seq=443 receive_seq=443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999503 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3547 bytes_read=10480 bytes_retransmit=9 bytes_invalid=0 send_seq=438 receive_seq=438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=28.8 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46623 bytes_read=333801 bytes_retransmit=0 bytes_invalid=0 send_seq=4075 receive_seq=4075 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999883 adj=31998671 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.011 th0: temp=43.3 th1: temp=42.0 th2: temp=43.1 th3: temp=41.3 sysload=0.23 cputime=47.190 memavail=7409788 print_time=377.706 buffer_time=2.121 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 354.2: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3232287 bytes_read=471583 bytes_retransmit=9 bytes_invalid=0 send_seq=60499 receive_seq=60498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=41588 freq=400015451 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2800 bytes_read=10668 bytes_retransmit=0 bytes_invalid=0 send_seq=438 receive_seq=438 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999937 adj=49999192 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=18655 bytes_read=403448 bytes_retransmit=9 bytes_invalid=0 send_seq=2238 receive_seq=2238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997725 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11892 bytes_read=53850 bytes_retransmit=9 bytes_invalid=0 send_seq=1181 receive_seq=1181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997600 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2959 bytes_read=85357 bytes_retransmit=9 bytes_invalid=0 send_seq=444 receive_seq=444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999503 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3553 bytes_read=10496 bytes_retransmit=9 bytes_invalid=0 send_seq=439 receive_seq=439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46629 bytes_read=334157 bytes_retransmit=0 bytes_invalid=0 send_seq=4076 receive_seq=4076 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998669 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=43.4 th1: temp=41.7 th2: temp=42.9 th3: temp=41.2 sysload=0.23 cputime=47.338 memavail=7409788 print_time=378.782 buffer_time=2.197 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 355.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3257060 bytes_read=473944 bytes_retransmit=9 bytes_invalid=0 send_seq=60905 receive_seq=60905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=43477 freq=400015458 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2806 bytes_read=10683 bytes_retransmit=0 bytes_invalid=0 send_seq=439 receive_seq=439 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999950 adj=49998934 toolboard_t0: mcu_awake=0.316 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=18731 bytes_read=406535 bytes_retransmit=9 bytes_invalid=0 send_seq=2249 receive_seq=2249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997532 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11898 bytes_read=53964 bytes_retransmit=9 bytes_invalid=0 send_seq=1182 receive_seq=1182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000002 adj=63997402 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2965 bytes_read=85591 bytes_retransmit=9 bytes_invalid=0 send_seq=445 receive_seq=445 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999503 adj=47997530 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3559 bytes_read=10512 bytes_retransmit=9 bytes_invalid=0 send_seq=440 receive_seq=440 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999419 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.2 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46635 bytes_read=334513 bytes_retransmit=0 bytes_invalid=0 send_seq=4077 receive_seq=4077 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998568 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=43.0 th1: temp=42.0 th2: temp=43.0 th3: temp=41.3 sysload=0.23 cputime=47.507 memavail=7411352 print_time=379.859 buffer_time=2.274 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 356.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3281835 bytes_read=476284 bytes_retransmit=9 bytes_invalid=0 send_seq=61303 receive_seq=61303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=45333 freq=400015461 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2818 bytes_read=10713 bytes_retransmit=0 bytes_invalid=0 send_seq=441 receive_seq=441 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999975 adj=49998875 toolboard_t0: mcu_awake=0.316 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=18813 bytes_read=409610 bytes_retransmit=9 bytes_invalid=0 send_seq=2261 receive_seq=2261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997552 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11910 bytes_read=54080 bytes_retransmit=9 bytes_invalid=0 send_seq=1184 receive_seq=1184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000000 adj=63997400 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2977 bytes_read=85841 bytes_retransmit=9 bytes_invalid=0 send_seq=447 receive_seq=447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999503 adj=47997543 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3571 bytes_read=10544 bytes_retransmit=9 bytes_invalid=0 send_seq=442 receive_seq=442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999421 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46647 bytes_read=334885 bytes_retransmit=0 bytes_invalid=0 send_seq=4079 receive_seq=4079 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998578 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.011 th0: temp=43.0 th1: temp=41.8 th2: temp=42.8 th3: temp=41.4 sysload=0.22 cputime=47.657 memavail=7411136 print_time=380.935 buffer_time=2.349 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 357.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3306594 bytes_read=478619 bytes_retransmit=9 bytes_invalid=0 send_seq=61708 receive_seq=61708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=47189 freq=400015461 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2824 bytes_read=10729 bytes_retransmit=0 bytes_invalid=0 send_seq=442 receive_seq=442 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999987 adj=49998966 toolboard_t0: mcu_awake=0.316 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=18889 bytes_read=412738 bytes_retransmit=9 bytes_invalid=0 send_seq=2272 receive_seq=2272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997574 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11916 bytes_read=54208 bytes_retransmit=9 bytes_invalid=0 send_seq=1185 receive_seq=1185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999999 adj=63997394 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=2983 bytes_read=86135 bytes_retransmit=9 bytes_invalid=0 send_seq=448 receive_seq=448 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999503 adj=47997559 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3577 bytes_read=10571 bytes_retransmit=9 bytes_invalid=0 send_seq=443 receive_seq=443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.2 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46653 bytes_read=335241 bytes_retransmit=0 bytes_invalid=0 send_seq=4080 receive_seq=4080 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998583 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=43.1 th1: temp=41.8 th2: temp=42.9 th3: temp=41.2 sysload=0.22 cputime=47.803 memavail=7411136 print_time=382.012 buffer_time=2.425 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 358.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3331422 bytes_read=480959 bytes_retransmit=9 bytes_invalid=0 send_seq=62114 receive_seq=62114 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=48999 freq=400015465 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2830 bytes_read=10758 bytes_retransmit=0 bytes_invalid=0 send_seq=443 receive_seq=443 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999999 adj=49998906 toolboard_t0: mcu_awake=0.316 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=18965 bytes_read=415808 bytes_retransmit=9 bytes_invalid=0 send_seq=2283 receive_seq=2283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997595 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11922 bytes_read=54322 bytes_retransmit=9 bytes_invalid=0 send_seq=1186 receive_seq=1186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997409 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2989 bytes_read=86384 bytes_retransmit=9 bytes_invalid=0 send_seq=449 receive_seq=449 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999504 adj=47997579 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3583 bytes_read=10587 bytes_retransmit=9 bytes_invalid=0 send_seq=444 receive_seq=444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.1 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46659 bytes_read=335597 bytes_retransmit=0 bytes_invalid=0 send_seq=4081 receive_seq=4081 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999883 adj=31998602 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=43.1 th1: temp=42.4 th2: temp=42.9 th3: temp=41.4 sysload=0.22 cputime=47.949 memavail=7411136 print_time=383.088 buffer_time=2.502 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 359.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3356174 bytes_read=483308 bytes_retransmit=9 bytes_invalid=0 send_seq=62516 receive_seq=62516 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=38670 freq=400015467 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2836 bytes_read=10774 bytes_retransmit=0 bytes_invalid=0 send_seq=444 receive_seq=444 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000008 adj=49998852 toolboard_t0: mcu_awake=0.316 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=19041 bytes_read=418865 bytes_retransmit=9 bytes_invalid=0 send_seq=2294 receive_seq=2294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997601 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11928 bytes_read=54422 bytes_retransmit=9 bytes_invalid=0 send_seq=1187 receive_seq=1187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997414 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2995 bytes_read=86618 bytes_retransmit=9 bytes_invalid=0 send_seq=450 receive_seq=450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999504 adj=47997603 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3589 bytes_read=10603 bytes_retransmit=9 bytes_invalid=0 send_seq=445 receive_seq=445 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.2 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46665 bytes_read=335953 bytes_retransmit=0 bytes_invalid=0 send_seq=4082 receive_seq=4082 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999883 adj=31998610 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=42.9 th1: temp=42.2 th2: temp=42.9 th3: temp=41.2 sysload=0.22 cputime=48.081 memavail=7411332 print_time=383.626 buffer_time=2.040 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 360.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3381031 bytes_read=485674 bytes_retransmit=9 bytes_invalid=0 send_seq=62924 receive_seq=62924 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=40461 freq=400015496 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2842 bytes_read=10790 bytes_retransmit=0 bytes_invalid=0 send_seq=445 receive_seq=445 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000017 adj=49998960 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=19117 bytes_read=421955 bytes_retransmit=9 bytes_invalid=0 send_seq=2305 receive_seq=2305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997598 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11934 bytes_read=54536 bytes_retransmit=9 bytes_invalid=0 send_seq=1188 receive_seq=1188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997402 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3001 bytes_read=86912 bytes_retransmit=9 bytes_invalid=0 send_seq=451 receive_seq=451 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999505 adj=47997596 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3595 bytes_read=10619 bytes_retransmit=9 bytes_invalid=0 send_seq=446 receive_seq=446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.2 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46671 bytes_read=336300 bytes_retransmit=0 bytes_invalid=0 send_seq=4083 receive_seq=4083 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999884 adj=31998615 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=42.8 th1: temp=42.1 th2: temp=42.9 th3: temp=41.4 sysload=0.22 cputime=48.228 memavail=7411108 print_time=384.703 buffer_time=2.116 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 361.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3406707 bytes_read=488089 bytes_retransmit=9 bytes_invalid=0 send_seq=63345 receive_seq=63345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=41491 freq=400015485 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2848 bytes_read=10806 bytes_retransmit=0 bytes_invalid=0 send_seq=446 receive_seq=446 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000026 adj=49998919 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=19186 bytes_read=425002 bytes_retransmit=9 bytes_invalid=0 send_seq=2315 receive_seq=2315 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000181 adj=63997546 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11940 bytes_read=54650 bytes_retransmit=9 bytes_invalid=0 send_seq=1189 receive_seq=1189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997367 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3007 bytes_read=87146 bytes_retransmit=9 bytes_invalid=0 send_seq=452 receive_seq=452 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999505 adj=47997573 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3601 bytes_read=10635 bytes_retransmit=9 bytes_invalid=0 send_seq=447 receive_seq=447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.2 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46677 bytes_read=336645 bytes_retransmit=0 bytes_invalid=0 send_seq=4084 receive_seq=4084 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999884 adj=31998600 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=43.2 th1: temp=42.3 th2: temp=43.2 th3: temp=41.4 sysload=0.28 cputime=48.376 memavail=7410856 print_time=385.779 buffer_time=2.191 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 362.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3431519 bytes_read=490463 bytes_retransmit=9 bytes_invalid=0 send_seq=63752 receive_seq=63752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=43347 freq=400015483 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2854 bytes_read=10822 bytes_retransmit=0 bytes_invalid=0 send_seq=447 receive_seq=447 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000036 adj=49998850 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=19262 bytes_read=428062 bytes_retransmit=9 bytes_invalid=0 send_seq=2326 receive_seq=2326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997592 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11946 bytes_read=54764 bytes_retransmit=9 bytes_invalid=0 send_seq=1190 receive_seq=1190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000000 adj=63997428 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3013 bytes_read=87380 bytes_retransmit=9 bytes_invalid=0 send_seq=453 receive_seq=453 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999505 adj=47997603 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3607 bytes_read=10662 bytes_retransmit=9 bytes_invalid=0 send_seq=448 receive_seq=448 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.2 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46683 bytes_read=336989 bytes_retransmit=0 bytes_invalid=0 send_seq=4085 receive_seq=4085 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999884 adj=31998624 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=43.3 th1: temp=41.7 th2: temp=43.0 th3: temp=41.1 sysload=0.28 cputime=48.532 memavail=7410624 print_time=386.856 buffer_time=2.267 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 363.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3456280 bytes_read=492793 bytes_retransmit=9 bytes_invalid=0 send_seq=64156 receive_seq=64156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=45203 freq=400015481 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2860 bytes_read=10851 bytes_retransmit=0 bytes_invalid=0 send_seq=448 receive_seq=448 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000044 adj=49998797 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=19338 bytes_read=431132 bytes_retransmit=9 bytes_invalid=0 send_seq=2337 receive_seq=2337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997613 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11952 bytes_read=54878 bytes_retransmit=9 bytes_invalid=0 send_seq=1191 receive_seq=1191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997471 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3019 bytes_read=87689 bytes_retransmit=9 bytes_invalid=0 send_seq=454 receive_seq=454 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999505 adj=47997614 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3613 bytes_read=10678 bytes_retransmit=9 bytes_invalid=0 send_seq=449 receive_seq=449 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=29.1 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46689 bytes_read=337334 bytes_retransmit=0 bytes_invalid=0 send_seq=4086 receive_seq=4086 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999884 adj=31998630 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=42.9 th1: temp=41.6 th2: temp=42.9 th3: temp=41.4 sysload=0.28 cputime=48.687 memavail=7410624 print_time=387.932 buffer_time=2.344 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 364.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3481069 bytes_read=495130 bytes_retransmit=9 bytes_invalid=0 send_seq=64562 receive_seq=64562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=47059 freq=400015517 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2866 bytes_read=10867 bytes_retransmit=0 bytes_invalid=0 send_seq=449 receive_seq=449 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000053 adj=49998744 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=19414 bytes_read=434203 bytes_retransmit=9 bytes_invalid=0 send_seq=2348 receive_seq=2348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997633 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11958 bytes_read=54992 bytes_retransmit=9 bytes_invalid=0 send_seq=1192 receive_seq=1192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997540 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3025 bytes_read=87923 bytes_retransmit=9 bytes_invalid=0 send_seq=455 receive_seq=455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999505 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3619 bytes_read=10694 bytes_retransmit=9 bytes_invalid=0 send_seq=450 receive_seq=450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.2 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46695 bytes_read=337679 bytes_retransmit=0 bytes_invalid=0 send_seq=4087 receive_seq=4087 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999883 adj=31998630 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=43.2 th1: temp=42.0 th2: temp=43.1 th3: temp=41.3 sysload=0.28 cputime=48.837 memavail=7410624 print_time=389.009 buffer_time=2.420 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 365.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3505924 bytes_read=497508 bytes_retransmit=9 bytes_invalid=0 send_seq=64967 receive_seq=64967 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=48871 freq=400015514 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2872 bytes_read=10883 bytes_retransmit=0 bytes_invalid=0 send_seq=450 receive_seq=450 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000060 adj=49998659 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=19490 bytes_read=437334 bytes_retransmit=9 bytes_invalid=0 send_seq=2359 receive_seq=2359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000179 adj=63997587 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11964 bytes_read=55092 bytes_retransmit=9 bytes_invalid=0 send_seq=1193 receive_seq=1193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997470 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3031 bytes_read=88157 bytes_retransmit=9 bytes_invalid=0 send_seq=456 receive_seq=456 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999507 adj=47997587 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3625 bytes_read=10710 bytes_retransmit=9 bytes_invalid=0 send_seq=451 receive_seq=451 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999422 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.2 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46701 bytes_read=338024 bytes_retransmit=0 bytes_invalid=0 send_seq=4088 receive_seq=4088 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999883 adj=31998598 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=43.3 th1: temp=42.0 th2: temp=42.8 th3: temp=41.4 sysload=0.28 cputime=48.987 memavail=7409392 print_time=390.085 buffer_time=2.495 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 366.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3530750 bytes_read=499858 bytes_retransmit=9 bytes_invalid=0 send_seq=65375 receive_seq=65375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=38505 freq=400015503 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2878 bytes_read=10899 bytes_retransmit=0 bytes_invalid=0 send_seq=451 receive_seq=451 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000067 adj=49998632 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=19566 bytes_read=440404 bytes_retransmit=9 bytes_invalid=0 send_seq=2370 receive_seq=2370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000179 adj=63997605 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11970 bytes_read=55206 bytes_retransmit=9 bytes_invalid=0 send_seq=1194 receive_seq=1194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997473 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3037 bytes_read=88451 bytes_retransmit=9 bytes_invalid=0 send_seq=457 receive_seq=457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999507 adj=47997617 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3631 bytes_read=10726 bytes_retransmit=9 bytes_invalid=0 send_seq=452 receive_seq=452 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.1 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46707 bytes_read=338369 bytes_retransmit=0 bytes_invalid=0 send_seq=4089 receive_seq=4089 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998603 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=43.2 th1: temp=42.1 th2: temp=43.2 th3: temp=41.4 sysload=0.26 cputime=49.119 memavail=7409392 print_time=390.623 buffer_time=2.032 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 367.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3555544 bytes_read=502198 bytes_retransmit=9 bytes_invalid=0 send_seq=65782 receive_seq=65781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=40361 freq=400015488 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2884 bytes_read=10915 bytes_retransmit=0 bytes_invalid=0 send_seq=452 receive_seq=452 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000072 adj=49998725 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=19642 bytes_read=443474 bytes_retransmit=9 bytes_invalid=0 send_seq=2381 receive_seq=2381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000181 adj=63997622 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11976 bytes_read=55334 bytes_retransmit=9 bytes_invalid=0 send_seq=1195 receive_seq=1195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997562 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3043 bytes_read=88685 bytes_retransmit=9 bytes_invalid=0 send_seq=458 receive_seq=458 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999507 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3637 bytes_read=10753 bytes_retransmit=9 bytes_invalid=0 send_seq=453 receive_seq=453 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46713 bytes_read=338714 bytes_retransmit=0 bytes_invalid=0 send_seq=4090 receive_seq=4090 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998608 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=43.0 th1: temp=42.0 th2: temp=43.0 th3: temp=41.3 sysload=0.26 cputime=49.267 memavail=7409392 print_time=391.700 buffer_time=2.108 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 368.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3581323 bytes_read=504652 bytes_retransmit=9 bytes_invalid=0 send_seq=66204 receive_seq=66204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=41289 freq=400015488 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2890 bytes_read=10944 bytes_retransmit=0 bytes_invalid=0 send_seq=453 receive_seq=453 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000079 adj=49998741 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=19718 bytes_read=446530 bytes_retransmit=9 bytes_invalid=0 send_seq=2392 receive_seq=2392 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997686 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11982 bytes_read=55434 bytes_retransmit=9 bytes_invalid=0 send_seq=1196 receive_seq=1196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997589 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3049 bytes_read=88934 bytes_retransmit=9 bytes_invalid=0 send_seq=459 receive_seq=459 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999507 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3643 bytes_read=10769 bytes_retransmit=9 bytes_invalid=0 send_seq=454 receive_seq=454 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.3 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46719 bytes_read=339064 bytes_retransmit=0 bytes_invalid=0 send_seq=4091 receive_seq=4091 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998627 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=43.1 th1: temp=42.4 th2: temp=43.2 th3: temp=41.5 sysload=0.26 cputime=49.420 memavail=7409392 print_time=392.776 buffer_time=2.185 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 369.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3606130 bytes_read=506992 bytes_retransmit=9 bytes_invalid=0 send_seq=66610 receive_seq=66610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=43145 freq=400015502 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2896 bytes_read=10960 bytes_retransmit=0 bytes_invalid=0 send_seq=454 receive_seq=454 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000084 adj=49998677 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=19794 bytes_read=449600 bytes_retransmit=9 bytes_invalid=0 send_seq=2403 receive_seq=2403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997683 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11988 bytes_read=55548 bytes_retransmit=9 bytes_invalid=0 send_seq=1197 receive_seq=1197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3055 bytes_read=89228 bytes_retransmit=9 bytes_invalid=0 send_seq=460 receive_seq=460 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999507 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3649 bytes_read=10785 bytes_retransmit=9 bytes_invalid=0 send_seq=455 receive_seq=455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.1 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46725 bytes_read=339420 bytes_retransmit=0 bytes_invalid=0 send_seq=4092 receive_seq=4092 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999883 adj=31998631 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=43.5 th1: temp=42.0 th2: temp=42.9 th3: temp=41.2 sysload=0.26 cputime=49.565 memavail=7409392 print_time=393.853 buffer_time=2.261 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 370.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3630919 bytes_read=509348 bytes_retransmit=9 bytes_invalid=0 send_seq=67016 receive_seq=67016 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=45001 freq=400015565 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2902 bytes_read=10976 bytes_retransmit=0 bytes_invalid=0 send_seq=455 receive_seq=455 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000089 adj=49998601 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=19870 bytes_read=452689 bytes_retransmit=9 bytes_invalid=0 send_seq=2414 receive_seq=2414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997724 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=11994 bytes_read=55662 bytes_retransmit=9 bytes_invalid=0 send_seq=1198 receive_seq=1198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997507 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3061 bytes_read=89462 bytes_retransmit=9 bytes_invalid=0 send_seq=461 receive_seq=461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999507 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3655 bytes_read=10801 bytes_retransmit=9 bytes_invalid=0 send_seq=456 receive_seq=456 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.1 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46731 bytes_read=339776 bytes_retransmit=0 bytes_invalid=0 send_seq=4093 receive_seq=4093 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999883 adj=31998623 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.3 th1: temp=42.2 th2: temp=43.4 th3: temp=41.3 sysload=0.26 cputime=49.718 memavail=7409408 print_time=394.929 buffer_time=2.337 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 371.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3655695 bytes_read=511722 bytes_retransmit=9 bytes_invalid=0 send_seq=67423 receive_seq=67423 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=46857 freq=400015563 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2908 bytes_read=10992 bytes_retransmit=0 bytes_invalid=0 send_seq=456 receive_seq=456 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000094 adj=49998473 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=19946 bytes_read=455750 bytes_retransmit=9 bytes_invalid=0 send_seq=2425 receive_seq=2425 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997593 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12000 bytes_read=55762 bytes_retransmit=9 bytes_invalid=0 send_seq=1199 receive_seq=1199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997389 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3067 bytes_read=89696 bytes_retransmit=9 bytes_invalid=0 send_seq=462 receive_seq=462 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999508 adj=47997549 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3661 bytes_read=10817 bytes_retransmit=9 bytes_invalid=0 send_seq=457 receive_seq=457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999416 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.2 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46737 bytes_read=340132 bytes_retransmit=0 bytes_invalid=0 send_seq=4094 receive_seq=4094 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999884 adj=31998579 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=42.9 th1: temp=41.8 th2: temp=42.9 th3: temp=41.4 sysload=0.24 cputime=49.870 memavail=7409408 print_time=396.006 buffer_time=2.412 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 372.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3680488 bytes_read=514067 bytes_retransmit=9 bytes_invalid=0 send_seq=67830 receive_seq=67830 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=48683 freq=400015559 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=2914 bytes_read=11008 bytes_retransmit=0 bytes_invalid=0 send_seq=457 receive_seq=457 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000098 adj=49998456 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=20022 bytes_read=458879 bytes_retransmit=9 bytes_invalid=0 send_seq=2436 receive_seq=2436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997718 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12006 bytes_read=55890 bytes_retransmit=9 bytes_invalid=0 send_seq=1200 receive_seq=1200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997438 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3073 bytes_read=89990 bytes_retransmit=9 bytes_invalid=0 send_seq=463 receive_seq=463 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999507 adj=47997583 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3667 bytes_read=10844 bytes_retransmit=9 bytes_invalid=0 send_seq=458 receive_seq=458 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999419 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.2 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46743 bytes_read=340488 bytes_retransmit=0 bytes_invalid=0 send_seq=4095 receive_seq=4095 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999884 adj=31998596 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=43.4 th1: temp=42.2 th2: temp=43.5 th3: temp=41.4 sysload=0.24 cputime=50.032 memavail=7409808 print_time=397.082 buffer_time=2.488 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 373.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3705327 bytes_read=516412 bytes_retransmit=9 bytes_invalid=0 send_seq=68238 receive_seq=68237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=38308 freq=400015536 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=2920 bytes_read=11037 bytes_retransmit=0 bytes_invalid=0 send_seq=458 receive_seq=458 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000101 adj=49998442 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=20091 bytes_read=461929 bytes_retransmit=9 bytes_invalid=0 send_seq=2446 receive_seq=2446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997711 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12012 bytes_read=56004 bytes_retransmit=9 bytes_invalid=0 send_seq=1201 receive_seq=1201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997446 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3079 bytes_read=90239 bytes_retransmit=9 bytes_invalid=0 send_seq=464 receive_seq=464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999509 adj=47997595 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3673 bytes_read=10860 bytes_retransmit=9 bytes_invalid=0 send_seq=459 receive_seq=459 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.4 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46749 bytes_read=340844 bytes_retransmit=0 bytes_invalid=0 send_seq=4096 receive_seq=4096 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999884 adj=31998617 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=43.1 th1: temp=42.1 th2: temp=43.1 th3: temp=41.6 sysload=0.24 cputime=50.162 memavail=7409808 print_time=397.620 buffer_time=2.025 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 374.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3730052 bytes_read=518781 bytes_retransmit=9 bytes_invalid=0 send_seq=68643 receive_seq=68643 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=40196 freq=400015521 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=2926 bytes_read=11053 bytes_retransmit=0 bytes_invalid=0 send_seq=459 receive_seq=459 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000105 adj=49998511 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=20167 bytes_read=464986 bytes_retransmit=9 bytes_invalid=0 send_seq=2457 receive_seq=2457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997741 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12018 bytes_read=56104 bytes_retransmit=9 bytes_invalid=0 send_seq=1202 receive_seq=1202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997472 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3085 bytes_read=90473 bytes_retransmit=9 bytes_invalid=0 send_seq=465 receive_seq=465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999508 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3679 bytes_read=10876 bytes_retransmit=9 bytes_invalid=0 send_seq=460 receive_seq=460 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.0 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46755 bytes_read=341200 bytes_retransmit=0 bytes_invalid=0 send_seq=4097 receive_seq=4097 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999883 adj=31998631 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=43.5 th1: temp=42.0 th2: temp=43.2 th3: temp=41.5 sysload=0.24 cputime=50.308 memavail=7409808 print_time=398.697 buffer_time=2.101 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 375.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3755892 bytes_read=521210 bytes_retransmit=9 bytes_invalid=0 send_seq=69065 receive_seq=69065 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=41124 freq=400015522 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=2932 bytes_read=11069 bytes_retransmit=0 bytes_invalid=0 send_seq=460 receive_seq=460 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000109 adj=49998541 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=20243 bytes_read=468073 bytes_retransmit=9 bytes_invalid=0 send_seq=2468 receive_seq=2468 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997759 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12024 bytes_read=56218 bytes_retransmit=9 bytes_invalid=0 send_seq=1203 receive_seq=1203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3091 bytes_read=90767 bytes_retransmit=9 bytes_invalid=0 send_seq=466 receive_seq=466 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999508 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3685 bytes_read=10892 bytes_retransmit=9 bytes_invalid=0 send_seq=461 receive_seq=461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.2 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46761 bytes_read=341556 bytes_retransmit=0 bytes_invalid=0 send_seq=4098 receive_seq=4098 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999883 adj=31998641 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=43.1 th1: temp=42.5 th2: temp=43.2 th3: temp=41.5 sysload=0.24 cputime=50.458 memavail=7409592 print_time=399.773 buffer_time=2.178 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 376.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3780633 bytes_read=523545 bytes_retransmit=9 bytes_invalid=0 send_seq=69470 receive_seq=69470 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=42980 freq=400015527 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=2938 bytes_read=11085 bytes_retransmit=0 bytes_invalid=0 send_seq=461 receive_seq=461 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000112 adj=49998503 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=20319 bytes_read=471145 bytes_retransmit=9 bytes_invalid=0 send_seq=2479 receive_seq=2479 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997738 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12030 bytes_read=56332 bytes_retransmit=9 bytes_invalid=0 send_seq=1204 receive_seq=1204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3097 bytes_read=91001 bytes_retransmit=9 bytes_invalid=0 send_seq=467 receive_seq=467 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999508 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3691 bytes_read=10908 bytes_retransmit=9 bytes_invalid=0 send_seq=462 receive_seq=462 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.1 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46767 bytes_read=341912 bytes_retransmit=0 bytes_invalid=0 send_seq=4099 receive_seq=4099 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999883 adj=31998640 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=43.4 th1: temp=42.5 th2: temp=43.1 th3: temp=41.6 sysload=0.22 cputime=50.606 memavail=7409592 print_time=400.850 buffer_time=2.254 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 377.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3805427 bytes_read=525919 bytes_retransmit=9 bytes_invalid=0 send_seq=69877 receive_seq=69877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=44836 freq=400015520 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=2944 bytes_read=11101 bytes_retransmit=0 bytes_invalid=0 send_seq=462 receive_seq=462 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000115 adj=49998456 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=20395 bytes_read=474205 bytes_retransmit=9 bytes_invalid=0 send_seq=2490 receive_seq=2490 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997718 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12036 bytes_read=56432 bytes_retransmit=9 bytes_invalid=0 send_seq=1205 receive_seq=1205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3103 bytes_read=91235 bytes_retransmit=9 bytes_invalid=0 send_seq=468 receive_seq=468 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999510 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3697 bytes_read=10935 bytes_retransmit=9 bytes_invalid=0 send_seq=463 receive_seq=463 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46773 bytes_read=342268 bytes_retransmit=0 bytes_invalid=0 send_seq=4100 receive_seq=4100 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999883 adj=31998632 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=43.4 th1: temp=42.2 th2: temp=43.4 th3: temp=41.8 sysload=0.22 cputime=50.753 memavail=7409592 print_time=401.926 buffer_time=2.330 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 378.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3830216 bytes_read=528259 bytes_retransmit=9 bytes_invalid=0 send_seq=70283 receive_seq=70283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=46692 freq=400015538 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2950 bytes_read=11130 bytes_retransmit=0 bytes_invalid=0 send_seq=463 receive_seq=463 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000116 adj=49998437 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=20471 bytes_read=477276 bytes_retransmit=9 bytes_invalid=0 send_seq=2501 receive_seq=2501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997709 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12042 bytes_read=56560 bytes_retransmit=9 bytes_invalid=0 send_seq=1206 receive_seq=1206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3109 bytes_read=91544 bytes_retransmit=9 bytes_invalid=0 send_seq=469 receive_seq=469 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999509 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3703 bytes_read=10951 bytes_retransmit=9 bytes_invalid=0 send_seq=464 receive_seq=464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.3 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46779 bytes_read=342624 bytes_retransmit=0 bytes_invalid=0 send_seq=4101 receive_seq=4101 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999882 adj=31998638 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=43.3 th1: temp=42.3 th2: temp=43.4 th3: temp=41.5 sysload=0.22 cputime=50.905 memavail=7409600 print_time=403.003 buffer_time=2.406 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 379.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3855019 bytes_read=530604 bytes_retransmit=9 bytes_invalid=0 send_seq=70690 receive_seq=70690 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=48548 freq=400015536 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2956 bytes_read=11146 bytes_retransmit=0 bytes_invalid=0 send_seq=464 receive_seq=464 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000117 adj=49998373 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=20547 bytes_read=480337 bytes_retransmit=9 bytes_invalid=0 send_seq=2512 receive_seq=2512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997665 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12048 bytes_read=56669 bytes_retransmit=9 bytes_invalid=0 send_seq=1207 receive_seq=1207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3115 bytes_read=91778 bytes_retransmit=9 bytes_invalid=0 send_seq=470 receive_seq=470 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999510 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3709 bytes_read=10967 bytes_retransmit=9 bytes_invalid=0 send_seq=465 receive_seq=465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=23.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46785 bytes_read=342980 bytes_retransmit=0 bytes_invalid=0 send_seq=4102 receive_seq=4102 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999883 adj=31998619 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=43.2 th1: temp=42.0 th2: temp=43.3 th3: temp=41.8 sysload=0.22 cputime=51.053 memavail=7409600 print_time=404.079 buffer_time=2.482 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 380.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3879842 bytes_read=533009 bytes_retransmit=9 bytes_invalid=0 send_seq=71100 receive_seq=71100 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=38175 freq=400015583 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2962 bytes_read=11162 bytes_retransmit=0 bytes_invalid=0 send_seq=465 receive_seq=465 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000118 adj=49998348 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=20623 bytes_read=483451 bytes_retransmit=9 bytes_invalid=0 send_seq=2523 receive_seq=2523 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997664 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12054 bytes_read=56762 bytes_retransmit=9 bytes_invalid=0 send_seq=1208 receive_seq=1208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3121 bytes_read=92012 bytes_retransmit=9 bytes_invalid=0 send_seq=471 receive_seq=471 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999512 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3715 bytes_read=10983 bytes_retransmit=9 bytes_invalid=0 send_seq=466 receive_seq=466 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46791 bytes_read=343336 bytes_retransmit=0 bytes_invalid=0 send_seq=4103 receive_seq=4103 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999883 adj=31998633 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=43.5 th1: temp=42.2 th2: temp=43.5 th3: temp=41.5 sysload=0.22 cputime=51.189 memavail=7409600 print_time=404.617 buffer_time=2.020 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 381.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3904636 bytes_read=535354 bytes_retransmit=9 bytes_invalid=0 send_seq=71507 receive_seq=71507 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=40031 freq=400015574 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2968 bytes_read=11178 bytes_retransmit=0 bytes_invalid=0 send_seq=466 receive_seq=466 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000119 adj=49998287 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=20699 bytes_read=486504 bytes_retransmit=9 bytes_invalid=0 send_seq=2534 receive_seq=2534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997562 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12060 bytes_read=56868 bytes_retransmit=9 bytes_invalid=0 send_seq=1209 receive_seq=1209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000001 adj=63997393 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3127 bytes_read=92306 bytes_retransmit=9 bytes_invalid=0 send_seq=472 receive_seq=472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999512 adj=47997608 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3721 bytes_read=10999 bytes_retransmit=9 bytes_invalid=0 send_seq=467 receive_seq=467 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999413 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.1 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46797 bytes_read=343692 bytes_retransmit=0 bytes_invalid=0 send_seq=4104 receive_seq=4104 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999884 adj=31998590 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=43.4 th1: temp=41.7 th2: temp=43.3 th3: temp=41.6 sysload=0.20 cputime=51.343 memavail=7409600 print_time=405.694 buffer_time=2.095 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 382.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3930416 bytes_read=537774 bytes_retransmit=9 bytes_invalid=0 send_seq=71929 receive_seq=71929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=40990 freq=400015572 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2974 bytes_read=11194 bytes_retransmit=0 bytes_invalid=0 send_seq=467 receive_seq=467 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000120 adj=49998305 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=20775 bytes_read=489558 bytes_retransmit=9 bytes_invalid=0 send_seq=2545 receive_seq=2545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997583 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12066 bytes_read=56974 bytes_retransmit=9 bytes_invalid=0 send_seq=1210 receive_seq=1210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000001 adj=63997408 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3133 bytes_read=92540 bytes_retransmit=9 bytes_invalid=0 send_seq=473 receive_seq=473 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3727 bytes_read=11026 bytes_retransmit=9 bytes_invalid=0 send_seq=468 receive_seq=468 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.2 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46803 bytes_read=344048 bytes_retransmit=0 bytes_invalid=0 send_seq=4105 receive_seq=4105 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999884 adj=31998611 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=43.4 th1: temp=42.7 th2: temp=43.4 th3: temp=41.8 sysload=0.20 cputime=51.491 memavail=7409600 print_time=406.770 buffer_time=2.171 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 383.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3955222 bytes_read=540143 bytes_retransmit=9 bytes_invalid=0 send_seq=72335 receive_seq=72335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=42846 freq=400015568 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2980 bytes_read=11223 bytes_retransmit=0 bytes_invalid=0 send_seq=468 receive_seq=468 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000121 adj=49998283 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=20851 bytes_read=492603 bytes_retransmit=9 bytes_invalid=0 send_seq=2556 receive_seq=2556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997607 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12072 bytes_read=57083 bytes_retransmit=9 bytes_invalid=0 send_seq=1211 receive_seq=1211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000002 adj=63997430 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3139 bytes_read=92789 bytes_retransmit=9 bytes_invalid=0 send_seq=474 receive_seq=474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999510 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3733 bytes_read=11042 bytes_retransmit=9 bytes_invalid=0 send_seq=469 receive_seq=469 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.3 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46809 bytes_read=344404 bytes_retransmit=0 bytes_invalid=0 send_seq=4106 receive_seq=4106 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999885 adj=31998626 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=43.7 th1: temp=41.9 th2: temp=43.2 th3: temp=41.6 sysload=0.20 cputime=51.639 memavail=7409600 print_time=407.847 buffer_time=2.247 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 384.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=3980011 bytes_read=542483 bytes_retransmit=9 bytes_invalid=0 send_seq=72741 receive_seq=72741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=44671 freq=400015575 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2986 bytes_read=11239 bytes_retransmit=0 bytes_invalid=0 send_seq=469 receive_seq=469 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000120 adj=49998274 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=20920 bytes_read=495665 bytes_retransmit=9 bytes_invalid=0 send_seq=2566 receive_seq=2566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997640 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12078 bytes_read=57211 bytes_retransmit=9 bytes_invalid=0 send_seq=1212 receive_seq=1212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000001 adj=63997466 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3145 bytes_read=93083 bytes_retransmit=9 bytes_invalid=0 send_seq=475 receive_seq=475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999513 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3739 bytes_read=11058 bytes_retransmit=9 bytes_invalid=0 send_seq=470 receive_seq=470 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46815 bytes_read=344760 bytes_retransmit=0 bytes_invalid=0 send_seq=4107 receive_seq=4107 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999884 adj=31998640 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=43.3 th1: temp=42.3 th2: temp=43.4 th3: temp=41.5 sysload=0.20 cputime=51.787 memavail=7409600 print_time=408.923 buffer_time=2.322 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 385.2: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4004773 bytes_read=544829 bytes_retransmit=9 bytes_invalid=0 send_seq=73145 receive_seq=73145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=46527 freq=400015570 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2992 bytes_read=11255 bytes_retransmit=0 bytes_invalid=0 send_seq=470 receive_seq=470 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000120 adj=49998240 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=20996 bytes_read=498741 bytes_retransmit=9 bytes_invalid=0 send_seq=2577 receive_seq=2577 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997633 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12084 bytes_read=57311 bytes_retransmit=9 bytes_invalid=0 send_seq=1213 receive_seq=1213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000000 adj=63997452 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3151 bytes_read=93317 bytes_retransmit=9 bytes_invalid=0 send_seq=476 receive_seq=476 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999513 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3745 bytes_read=11074 bytes_retransmit=9 bytes_invalid=0 send_seq=471 receive_seq=471 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.2 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46821 bytes_read=345116 bytes_retransmit=0 bytes_invalid=0 send_seq=4108 receive_seq=4108 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999885 adj=31998628 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=43.3 th1: temp=42.3 th2: temp=43.6 th3: temp=41.7 sysload=0.20 cputime=51.937 memavail=7408612 print_time=410.000 buffer_time=2.398 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 386.2: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4029552 bytes_read=547183 bytes_retransmit=9 bytes_invalid=0 send_seq=73549 receive_seq=73549 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=48383 freq=400015549 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=2998 bytes_read=11271 bytes_retransmit=0 bytes_invalid=0 send_seq=471 receive_seq=471 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000119 adj=49998228 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=21072 bytes_read=501797 bytes_retransmit=9 bytes_invalid=0 send_seq=2588 receive_seq=2588 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997725 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12090 bytes_read=57411 bytes_retransmit=9 bytes_invalid=0 send_seq=1214 receive_seq=1214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997459 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3157 bytes_read=93551 bytes_retransmit=9 bytes_invalid=0 send_seq=477 receive_seq=477 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999512 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3751 bytes_read=11090 bytes_retransmit=9 bytes_invalid=0 send_seq=472 receive_seq=472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.4 EBB42_Gen2_v1.0_T0: temp=29.4 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46827 bytes_read=345472 bytes_retransmit=0 bytes_invalid=0 send_seq=4109 receive_seq=4109 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999886 adj=31998647 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=43.0 th1: temp=42.2 th2: temp=43.4 th3: temp=41.8 sysload=0.18 cputime=52.083 memavail=7408364 print_time=411.076 buffer_time=2.474 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 387.2: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4054431 bytes_read=549533 bytes_retransmit=9 bytes_invalid=0 send_seq=73957 receive_seq=73957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=37974 freq=400015552 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3004 bytes_read=11287 bytes_retransmit=0 bytes_invalid=0 send_seq=472 receive_seq=472 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000119 adj=49998237 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=21148 bytes_read=504940 bytes_retransmit=9 bytes_invalid=0 send_seq=2599 receive_seq=2599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997744 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12096 bytes_read=57539 bytes_retransmit=9 bytes_invalid=0 send_seq=1215 receive_seq=1215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3163 bytes_read=93845 bytes_retransmit=9 bytes_invalid=0 send_seq=478 receive_seq=478 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3757 bytes_read=11117 bytes_retransmit=9 bytes_invalid=0 send_seq=473 receive_seq=473 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46833 bytes_read=345828 bytes_retransmit=0 bytes_invalid=0 send_seq=4110 receive_seq=4110 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999885 adj=31998665 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=43.7 th1: temp=42.2 th2: temp=43.4 th3: temp=41.8 sysload=0.18 cputime=52.221 memavail=7408388 print_time=411.614 buffer_time=2.012 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 388.2: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4079210 bytes_read=551863 bytes_retransmit=9 bytes_invalid=0 send_seq=74361 receive_seq=74361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=39799 freq=400015550 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=3010 bytes_read=11316 bytes_retransmit=0 bytes_invalid=0 send_seq=473 receive_seq=473 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000119 adj=49998233 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=21224 bytes_read=507996 bytes_retransmit=9 bytes_invalid=0 send_seq=2610 receive_seq=2610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997722 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12102 bytes_read=57653 bytes_retransmit=9 bytes_invalid=0 send_seq=1216 receive_seq=1216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997475 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3169 bytes_read=94094 bytes_retransmit=9 bytes_invalid=0 send_seq=479 receive_seq=479 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3763 bytes_read=11133 bytes_retransmit=9 bytes_invalid=0 send_seq=474 receive_seq=474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46839 bytes_read=346184 bytes_retransmit=0 bytes_invalid=0 send_seq=4111 receive_seq=4111 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999889 adj=31998660 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=43.6 th1: temp=42.4 th2: temp=42.9 th3: temp=41.6 sysload=0.18 cputime=52.389 memavail=7407632 print_time=412.691 buffer_time=2.087 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 389.2: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4104934 bytes_read=554297 bytes_retransmit=9 bytes_invalid=0 send_seq=74780 receive_seq=74780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=40795 freq=400015543 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=3016 bytes_read=11332 bytes_retransmit=0 bytes_invalid=0 send_seq=474 receive_seq=474 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000119 adj=49998228 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=21300 bytes_read=511053 bytes_retransmit=9 bytes_invalid=0 send_seq=2621 receive_seq=2621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997709 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12108 bytes_read=57753 bytes_retransmit=9 bytes_invalid=0 send_seq=1217 receive_seq=1217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999996 adj=63997474 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3175 bytes_read=94328 bytes_retransmit=9 bytes_invalid=0 send_seq=480 receive_seq=480 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999510 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3769 bytes_read=11149 bytes_retransmit=9 bytes_invalid=0 send_seq=475 receive_seq=475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46845 bytes_read=346540 bytes_retransmit=0 bytes_invalid=0 send_seq=4112 receive_seq=4112 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999888 adj=31998703 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=43.4 th1: temp=42.6 th2: temp=43.3 th3: temp=41.7 sysload=0.18 cputime=52.552 memavail=7403112 print_time=413.767 buffer_time=2.163 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 390.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4129781 bytes_read=556653 bytes_retransmit=9 bytes_invalid=0 send_seq=75186 receive_seq=75186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=42614 freq=400015544 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=3022 bytes_read=11348 bytes_retransmit=0 bytes_invalid=0 send_seq=475 receive_seq=475 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000118 adj=49998224 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=21376 bytes_read=514156 bytes_retransmit=9 bytes_invalid=0 send_seq=2632 receive_seq=2632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997708 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12114 bytes_read=57881 bytes_retransmit=9 bytes_invalid=0 send_seq=1218 receive_seq=1218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997483 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3181 bytes_read=94622 bytes_retransmit=9 bytes_invalid=0 send_seq=481 receive_seq=481 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999509 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3775 bytes_read=11165 bytes_retransmit=9 bytes_invalid=0 send_seq=476 receive_seq=476 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46851 bytes_read=346896 bytes_retransmit=0 bytes_invalid=0 send_seq=4113 receive_seq=4113 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999891 adj=31998689 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.011 th0: temp=43.6 th1: temp=42.2 th2: temp=43.8 th3: temp=42.0 sysload=0.18 cputime=52.703 memavail=7408996 print_time=414.844 buffer_time=2.239 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 391.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4154530 bytes_read=558993 bytes_retransmit=9 bytes_invalid=0 send_seq=75592 receive_seq=75592 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=44507 freq=400015527 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=3028 bytes_read=11364 bytes_retransmit=0 bytes_invalid=0 send_seq=476 receive_seq=476 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000118 adj=49998206 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=21452 bytes_read=517213 bytes_retransmit=9 bytes_invalid=0 send_seq=2643 receive_seq=2643 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997695 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12120 bytes_read=57981 bytes_retransmit=9 bytes_invalid=0 send_seq=1219 receive_seq=1219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999996 adj=63997502 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3187 bytes_read=94856 bytes_retransmit=9 bytes_invalid=0 send_seq=482 receive_seq=482 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999509 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3781 bytes_read=11181 bytes_retransmit=9 bytes_invalid=0 send_seq=477 receive_seq=477 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.3 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46857 bytes_read=347252 bytes_retransmit=0 bytes_invalid=0 send_seq=4114 receive_seq=4114 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999890 adj=31998711 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=43.4 th1: temp=42.5 th2: temp=43.5 th3: temp=41.8 sysload=0.17 cputime=52.846 memavail=7408996 print_time=415.920 buffer_time=2.315 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 392.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4179314 bytes_read=561357 bytes_retransmit=9 bytes_invalid=0 send_seq=75997 receive_seq=75997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=46363 freq=400015596 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=3034 bytes_read=11380 bytes_retransmit=0 bytes_invalid=0 send_seq=477 receive_seq=477 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000116 adj=49998217 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=21528 bytes_read=520269 bytes_retransmit=9 bytes_invalid=0 send_seq=2654 receive_seq=2654 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997718 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12126 bytes_read=58081 bytes_retransmit=9 bytes_invalid=0 send_seq=1220 receive_seq=1220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997522 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3193 bytes_read=95090 bytes_retransmit=9 bytes_invalid=0 send_seq=483 receive_seq=483 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999508 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3787 bytes_read=11208 bytes_retransmit=9 bytes_invalid=0 send_seq=478 receive_seq=478 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46863 bytes_read=347592 bytes_retransmit=0 bytes_invalid=0 send_seq=4115 receive_seq=4115 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998706 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.8 th1: temp=42.6 th2: temp=43.5 th3: temp=41.8 sysload=0.17 cputime=52.995 memavail=7408996 print_time=416.997 buffer_time=2.391 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 393.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4204160 bytes_read=563692 bytes_retransmit=9 bytes_invalid=0 send_seq=76403 receive_seq=76402 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=48182 freq=400015645 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=3040 bytes_read=11396 bytes_retransmit=0 bytes_invalid=0 send_seq=478 receive_seq=478 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000113 adj=49998088 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=21604 bytes_read=523353 bytes_retransmit=9 bytes_invalid=0 send_seq=2665 receive_seq=2665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997582 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12132 bytes_read=58223 bytes_retransmit=9 bytes_invalid=0 send_seq=1221 receive_seq=1221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999996 adj=63997406 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3199 bytes_read=95399 bytes_retransmit=9 bytes_invalid=0 send_seq=484 receive_seq=484 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999509 adj=47997559 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3793 bytes_read=11224 bytes_retransmit=9 bytes_invalid=0 send_seq=479 receive_seq=479 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46869 bytes_read=347948 bytes_retransmit=0 bytes_invalid=0 send_seq=4116 receive_seq=4116 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999892 adj=31998656 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.5 th1: temp=42.4 th2: temp=43.5 th3: temp=41.9 sysload=0.17 cputime=53.142 memavail=7408996 print_time=418.073 buffer_time=2.467 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 394.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4228982 bytes_read=566047 bytes_retransmit=9 bytes_invalid=0 send_seq=76811 receive_seq=76811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=37809 freq=400015634 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3046 bytes_read=11425 bytes_retransmit=0 bytes_invalid=0 send_seq=479 receive_seq=479 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000111 adj=49998012 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=21680 bytes_read=526467 bytes_retransmit=9 bytes_invalid=0 send_seq=2676 receive_seq=2676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997622 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12138 bytes_read=58323 bytes_retransmit=9 bytes_invalid=0 send_seq=1222 receive_seq=1222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999996 adj=63997335 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3205 bytes_read=95633 bytes_retransmit=9 bytes_invalid=0 send_seq=485 receive_seq=485 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999509 adj=47997518 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3799 bytes_read=11240 bytes_retransmit=9 bytes_invalid=0 send_seq=480 receive_seq=480 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999418 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46875 bytes_read=348304 bytes_retransmit=0 bytes_invalid=0 send_seq=4117 receive_seq=4117 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999899 adj=31998610 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.4 th1: temp=42.5 th2: temp=43.4 th3: temp=41.7 sysload=0.17 cputime=53.272 memavail=7408996 print_time=418.611 buffer_time=2.004 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 395.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4253756 bytes_read=568417 bytes_retransmit=9 bytes_invalid=0 send_seq=77214 receive_seq=77214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=39665 freq=400015628 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3052 bytes_read=11441 bytes_retransmit=0 bytes_invalid=0 send_seq=480 receive_seq=480 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000110 adj=49998007 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=21756 bytes_read=529540 bytes_retransmit=9 bytes_invalid=0 send_seq=2687 receive_seq=2687 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997623 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12144 bytes_read=58423 bytes_retransmit=9 bytes_invalid=0 send_seq=1223 receive_seq=1223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999996 adj=63997358 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3211 bytes_read=95867 bytes_retransmit=9 bytes_invalid=0 send_seq=486 receive_seq=486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999509 adj=47997533 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3805 bytes_read=11256 bytes_retransmit=9 bytes_invalid=0 send_seq=481 receive_seq=481 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999418 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.5 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46881 bytes_read=348660 bytes_retransmit=0 bytes_invalid=0 send_seq=4118 receive_seq=4118 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999902 adj=31998693 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.5 th1: temp=42.5 th2: temp=43.4 th3: temp=41.9 sysload=0.17 cputime=53.421 memavail=7408296 print_time=419.688 buffer_time=2.080 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 396.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4279553 bytes_read=570835 bytes_retransmit=9 bytes_invalid=0 send_seq=77636 receive_seq=77636 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=40593 freq=400015615 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3058 bytes_read=11457 bytes_retransmit=0 bytes_invalid=0 send_seq=481 receive_seq=481 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000108 adj=49998014 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=21825 bytes_read=532602 bytes_retransmit=9 bytes_invalid=0 send_seq=2697 receive_seq=2697 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997630 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12150 bytes_read=58551 bytes_retransmit=9 bytes_invalid=0 send_seq=1224 receive_seq=1224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999996 adj=63997378 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3217 bytes_read=96161 bytes_retransmit=9 bytes_invalid=0 send_seq=487 receive_seq=487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999509 adj=47997550 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3811 bytes_read=11272 bytes_retransmit=9 bytes_invalid=0 send_seq=482 receive_seq=482 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999420 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46887 bytes_read=349016 bytes_retransmit=0 bytes_invalid=0 send_seq=4119 receive_seq=4119 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998732 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.5 th1: temp=42.6 th2: temp=43.7 th3: temp=41.8 sysload=0.15 cputime=53.572 memavail=7408296 print_time=420.764 buffer_time=2.156 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 397.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4304347 bytes_read=573177 bytes_retransmit=9 bytes_invalid=0 send_seq=78043 receive_seq=78043 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=42449 freq=400015585 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3064 bytes_read=11473 bytes_retransmit=0 bytes_invalid=0 send_seq=482 receive_seq=482 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000106 adj=49998040 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=21901 bytes_read=535659 bytes_retransmit=9 bytes_invalid=0 send_seq=2708 receive_seq=2708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997885 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12156 bytes_read=58651 bytes_retransmit=9 bytes_invalid=0 send_seq=1225 receive_seq=1225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997441 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3223 bytes_read=96395 bytes_retransmit=9 bytes_invalid=0 send_seq=488 receive_seq=488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999508 adj=47997588 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3817 bytes_read=11299 bytes_retransmit=9 bytes_invalid=0 send_seq=483 receive_seq=483 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46893 bytes_read=349372 bytes_retransmit=0 bytes_invalid=0 send_seq=4120 receive_seq=4120 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999904 adj=31998713 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.7 th1: temp=42.4 th2: temp=43.9 th3: temp=41.9 sysload=0.15 cputime=53.722 memavail=7408296 print_time=421.841 buffer_time=2.232 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 398.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4329131 bytes_read=575541 bytes_retransmit=9 bytes_invalid=0 send_seq=78448 receive_seq=78448 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=44305 freq=400015564 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3070 bytes_read=11489 bytes_retransmit=0 bytes_invalid=0 send_seq=483 receive_seq=483 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000102 adj=49998088 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=21977 bytes_read=538715 bytes_retransmit=9 bytes_invalid=0 send_seq=2719 receive_seq=2719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997875 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12162 bytes_read=58765 bytes_retransmit=9 bytes_invalid=0 send_seq=1226 receive_seq=1226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999996 adj=63997517 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3229 bytes_read=96644 bytes_retransmit=9 bytes_invalid=0 send_seq=489 receive_seq=489 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999508 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3823 bytes_read=11315 bytes_retransmit=9 bytes_invalid=0 send_seq=484 receive_seq=484 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.3 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46899 bytes_read=349728 bytes_retransmit=0 bytes_invalid=0 send_seq=4121 receive_seq=4121 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999903 adj=31998762 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.4 th1: temp=42.6 th2: temp=43.4 th3: temp=41.9 sysload=0.15 cputime=53.876 memavail=7408296 print_time=422.917 buffer_time=2.308 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 399.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4353930 bytes_read=577891 bytes_retransmit=9 bytes_invalid=0 send_seq=78856 receive_seq=78856 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=46161 freq=400015547 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3076 bytes_read=11518 bytes_retransmit=0 bytes_invalid=0 send_seq=484 receive_seq=484 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000101 adj=49998097 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=22053 bytes_read=541800 bytes_retransmit=9 bytes_invalid=0 send_seq=2730 receive_seq=2730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997986 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12168 bytes_read=58893 bytes_retransmit=9 bytes_invalid=0 send_seq=1227 receive_seq=1227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999996 adj=63997545 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3235 bytes_read=96938 bytes_retransmit=9 bytes_invalid=0 send_seq=490 receive_seq=490 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999507 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3829 bytes_read=11331 bytes_retransmit=9 bytes_invalid=0 send_seq=485 receive_seq=485 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46905 bytes_read=350084 bytes_retransmit=0 bytes_invalid=0 send_seq=4122 receive_seq=4122 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999902 adj=31998749 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.8 th1: temp=42.5 th2: temp=43.6 th3: temp=41.9 sysload=0.15 cputime=54.027 memavail=7408296 print_time=423.994 buffer_time=2.384 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 400.2: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4378724 bytes_read=580247 bytes_retransmit=9 bytes_invalid=0 send_seq=79263 receive_seq=79262 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=48017 freq=400015557 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3082 bytes_read=11534 bytes_retransmit=0 bytes_invalid=0 send_seq=485 receive_seq=485 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000098 adj=49998114 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=22129 bytes_read=544875 bytes_retransmit=9 bytes_invalid=0 send_seq=2741 receive_seq=2741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997944 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12174 bytes_read=58993 bytes_retransmit=9 bytes_invalid=0 send_seq=1228 receive_seq=1228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997562 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3241 bytes_read=97172 bytes_retransmit=9 bytes_invalid=0 send_seq=491 receive_seq=491 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999508 adj=47997677 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3835 bytes_read=11347 bytes_retransmit=9 bytes_invalid=0 send_seq=486 receive_seq=486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46911 bytes_read=350440 bytes_retransmit=0 bytes_invalid=0 send_seq=4123 receive_seq=4123 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998734 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.5 th1: temp=42.4 th2: temp=43.6 th3: temp=41.7 sysload=0.15 cputime=54.170 memavail=7408296 print_time=425.070 buffer_time=2.460 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 401.2: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4403796 bytes_read=582646 bytes_retransmit=9 bytes_invalid=0 send_seq=79675 receive_seq=79674 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=49596 freq=400015558 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3088 bytes_read=11550 bytes_retransmit=0 bytes_invalid=0 send_seq=486 receive_seq=486 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000096 adj=49998084 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=22205 bytes_read=547989 bytes_retransmit=9 bytes_invalid=0 send_seq=2752 receive_seq=2752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997859 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12180 bytes_read=59093 bytes_retransmit=9 bytes_invalid=0 send_seq=1229 receive_seq=1229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997529 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3247 bytes_read=97406 bytes_retransmit=9 bytes_invalid=0 send_seq=492 receive_seq=492 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999513 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3841 bytes_read=11363 bytes_retransmit=9 bytes_invalid=0 send_seq=487 receive_seq=487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46917 bytes_read=350796 bytes_retransmit=0 bytes_invalid=0 send_seq=4124 receive_seq=4124 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998701 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.7 th1: temp=42.4 th2: temp=43.7 th3: temp=42.0 sysload=0.14 cputime=54.320 memavail=7408296 print_time=426.147 buffer_time=2.525 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 402.2: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4428590 bytes_read=584996 bytes_retransmit=9 bytes_invalid=0 send_seq=80082 receive_seq=80082 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=39236 freq=400015545 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3094 bytes_read=11566 bytes_retransmit=0 bytes_invalid=0 send_seq=487 receive_seq=487 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000093 adj=49998069 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=22281 bytes_read=551074 bytes_retransmit=9 bytes_invalid=0 send_seq=2763 receive_seq=2763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997801 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12186 bytes_read=59221 bytes_retransmit=9 bytes_invalid=0 send_seq=1230 receive_seq=1230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3253 bytes_read=97700 bytes_retransmit=9 bytes_invalid=0 send_seq=493 receive_seq=493 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999512 adj=47997714 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3847 bytes_read=11389 bytes_retransmit=9 bytes_invalid=0 send_seq=488 receive_seq=488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.5 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46923 bytes_read=351152 bytes_retransmit=0 bytes_invalid=0 send_seq=4125 receive_seq=4125 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999899 adj=31998688 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.0 th1: temp=42.6 th2: temp=43.8 th3: temp=41.6 sysload=0.14 cputime=54.455 memavail=7408296 print_time=426.685 buffer_time=2.062 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 403.2: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4454071 bytes_read=587391 bytes_retransmit=9 bytes_invalid=0 send_seq=80499 receive_seq=80499 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400015531 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3100 bytes_read=11582 bytes_retransmit=0 bytes_invalid=0 send_seq=488 receive_seq=488 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000090 adj=49998059 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=22357 bytes_read=554131 bytes_retransmit=9 bytes_invalid=0 send_seq=2774 receive_seq=2774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997905 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12192 bytes_read=59335 bytes_retransmit=9 bytes_invalid=0 send_seq=1231 receive_seq=1231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999996 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3259 bytes_read=97949 bytes_retransmit=9 bytes_invalid=0 send_seq=494 receive_seq=494 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999512 adj=47997721 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3853 bytes_read=11404 bytes_retransmit=9 bytes_invalid=0 send_seq=489 receive_seq=489 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.1 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46929 bytes_read=351508 bytes_retransmit=0 bytes_invalid=0 send_seq=4126 receive_seq=4126 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999898 adj=31998682 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.8 th1: temp=42.7 th2: temp=43.8 th3: temp=42.0 sysload=0.14 cputime=54.603 memavail=7408296 print_time=427.761 buffer_time=2.138 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 404.2: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4479186 bytes_read=589795 bytes_retransmit=9 bytes_invalid=0 send_seq=80912 receive_seq=80912 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=42020 freq=400015528 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3106 bytes_read=11611 bytes_retransmit=0 bytes_invalid=0 send_seq=489 receive_seq=489 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000086 adj=49998049 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=22433 bytes_read=557188 bytes_retransmit=9 bytes_invalid=0 send_seq=2785 receive_seq=2785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997890 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12198 bytes_read=59435 bytes_retransmit=9 bytes_invalid=0 send_seq=1232 receive_seq=1232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997575 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3265 bytes_read=98183 bytes_retransmit=9 bytes_invalid=0 send_seq=495 receive_seq=495 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999512 adj=47997725 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3859 bytes_read=11419 bytes_retransmit=9 bytes_invalid=0 send_seq=490 receive_seq=490 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46935 bytes_read=351864 bytes_retransmit=0 bytes_invalid=0 send_seq=4127 receive_seq=4127 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999897 adj=31998682 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.6 th1: temp=42.6 th2: temp=43.6 th3: temp=42.0 sysload=0.14 cputime=54.752 memavail=7408320 print_time=428.838 buffer_time=2.213 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 405.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4504039 bytes_read=592156 bytes_retransmit=9 bytes_invalid=0 send_seq=81319 receive_seq=81319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=43841 freq=400015524 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3112 bytes_read=11627 bytes_retransmit=0 bytes_invalid=0 send_seq=490 receive_seq=490 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000083 adj=49998033 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=22509 bytes_read=560347 bytes_retransmit=9 bytes_invalid=0 send_seq=2796 receive_seq=2796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997830 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12204 bytes_read=59563 bytes_retransmit=9 bytes_invalid=0 send_seq=1233 receive_seq=1233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999996 adj=63997557 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3271 bytes_read=98477 bytes_retransmit=9 bytes_invalid=0 send_seq=496 receive_seq=496 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997712 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3865 bytes_read=11434 bytes_retransmit=9 bytes_invalid=0 send_seq=491 receive_seq=491 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46941 bytes_read=352220 bytes_retransmit=0 bytes_invalid=0 send_seq=4128 receive_seq=4128 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998663 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.7 th1: temp=42.8 th2: temp=43.6 th3: temp=42.0 sysload=0.14 cputime=54.904 memavail=7407816 print_time=429.914 buffer_time=2.289 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 406.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4528818 bytes_read=594486 bytes_retransmit=9 bytes_invalid=0 send_seq=81723 receive_seq=81723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=45697 freq=400015523 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3118 bytes_read=11643 bytes_retransmit=0 bytes_invalid=0 send_seq=491 receive_seq=491 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000079 adj=49998030 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=22585 bytes_read=563405 bytes_retransmit=9 bytes_invalid=0 send_seq=2807 receive_seq=2807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997858 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12210 bytes_read=59663 bytes_retransmit=9 bytes_invalid=0 send_seq=1234 receive_seq=1234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3277 bytes_read=98711 bytes_retransmit=9 bytes_invalid=0 send_seq=497 receive_seq=497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3871 bytes_read=11449 bytes_retransmit=9 bytes_invalid=0 send_seq=492 receive_seq=492 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=29.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46947 bytes_read=352576 bytes_retransmit=0 bytes_invalid=0 send_seq=4129 receive_seq=4129 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998651 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.3 th1: temp=42.6 th2: temp=43.7 th3: temp=41.8 sysload=0.13 cputime=55.061 memavail=7402524 print_time=430.991 buffer_time=2.365 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 407.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4553602 bytes_read=596846 bytes_retransmit=9 bytes_invalid=0 send_seq=82128 receive_seq=82128 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=47553 freq=400015592 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3124 bytes_read=11659 bytes_retransmit=0 bytes_invalid=0 send_seq=492 receive_seq=492 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000076 adj=49998008 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=22661 bytes_read=566462 bytes_retransmit=9 bytes_invalid=0 send_seq=2818 receive_seq=2818 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997854 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12216 bytes_read=59763 bytes_retransmit=9 bytes_invalid=0 send_seq=1235 receive_seq=1235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997546 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3283 bytes_read=98945 bytes_retransmit=9 bytes_invalid=0 send_seq=498 receive_seq=498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999510 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3877 bytes_read=11475 bytes_retransmit=9 bytes_invalid=0 send_seq=493 receive_seq=493 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.5 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46953 bytes_read=352932 bytes_retransmit=0 bytes_invalid=0 send_seq=4130 receive_seq=4130 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999897 adj=31998638 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.9 th1: temp=42.6 th2: temp=43.8 th3: temp=41.9 sysload=0.13 cputime=55.208 memavail=7408956 print_time=432.067 buffer_time=2.441 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 408.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4578343 bytes_read=599175 bytes_retransmit=9 bytes_invalid=0 send_seq=82532 receive_seq=82532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=49396 freq=400015610 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3130 bytes_read=11675 bytes_retransmit=0 bytes_invalid=0 send_seq=493 receive_seq=493 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000072 adj=49997903 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=22737 bytes_read=569548 bytes_retransmit=9 bytes_invalid=0 send_seq=2829 receive_seq=2829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997672 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12222 bytes_read=59905 bytes_retransmit=9 bytes_invalid=0 send_seq=1236 receive_seq=1236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997420 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3289 bytes_read=99254 bytes_retransmit=9 bytes_invalid=0 send_seq=499 receive_seq=499 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999510 adj=47997582 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3883 bytes_read=11490 bytes_retransmit=9 bytes_invalid=0 send_seq=494 receive_seq=494 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999420 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46959 bytes_read=353288 bytes_retransmit=0 bytes_invalid=0 send_seq=4131 receive_seq=4131 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999897 adj=31998614 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.8 th1: temp=42.7 th2: temp=43.9 th3: temp=42.0 sysload=0.13 cputime=55.357 memavail=7408956 print_time=433.144 buffer_time=2.517 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 409.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4603196 bytes_read=601515 bytes_retransmit=9 bytes_invalid=0 send_seq=82939 receive_seq=82938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=39004 freq=400015637 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3136 bytes_read=11704 bytes_retransmit=0 bytes_invalid=0 send_seq=494 receive_seq=494 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000068 adj=49997883 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=22806 bytes_read=572584 bytes_retransmit=9 bytes_invalid=0 send_seq=2839 receive_seq=2839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997618 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12228 bytes_read=60005 bytes_retransmit=9 bytes_invalid=0 send_seq=1237 receive_seq=1237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997408 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3295 bytes_read=99488 bytes_retransmit=9 bytes_invalid=0 send_seq=500 receive_seq=500 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997566 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3889 bytes_read=11505 bytes_retransmit=9 bytes_invalid=0 send_seq=495 receive_seq=495 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999419 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.5 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46965 bytes_read=353644 bytes_retransmit=0 bytes_invalid=0 send_seq=4132 receive_seq=4132 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999897 adj=31998597 coil_temp=17.6 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=43.7 th1: temp=42.7 th2: temp=43.6 th3: temp=42.1 sysload=0.13 cputime=55.489 memavail=7408964 print_time=433.682 buffer_time=2.054 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 410.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4628380 bytes_read=603895 bytes_retransmit=9 bytes_invalid=0 send_seq=83343 receive_seq=83343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400015664 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3142 bytes_read=11720 bytes_retransmit=0 bytes_invalid=0 send_seq=495 receive_seq=495 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000064 adj=49997800 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=22882 bytes_read=575659 bytes_retransmit=9 bytes_invalid=0 send_seq=2850 receive_seq=2850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997537 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12234 bytes_read=60105 bytes_retransmit=9 bytes_invalid=0 send_seq=1238 receive_seq=1238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999994 adj=63997352 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3301 bytes_read=99722 bytes_retransmit=9 bytes_invalid=0 send_seq=501 receive_seq=501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999514 adj=47997581 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3895 bytes_read=11520 bytes_retransmit=9 bytes_invalid=0 send_seq=496 receive_seq=496 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999407 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.6 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46971 bytes_read=354000 bytes_retransmit=0 bytes_invalid=0 send_seq=4133 receive_seq=4133 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999897 adj=31998580 coil_temp=17.6 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=43.9 th1: temp=42.5 th2: temp=43.9 th3: temp=42.0 sysload=0.13 cputime=55.637 memavail=7408964 print_time=434.758 buffer_time=2.130 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 411.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4653688 bytes_read=606290 bytes_retransmit=9 bytes_invalid=0 send_seq=83760 receive_seq=83760 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=41820 freq=400015663 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3148 bytes_read=11736 bytes_retransmit=0 bytes_invalid=0 send_seq=496 receive_seq=496 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000063 adj=49997746 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=22958 bytes_read=578744 bytes_retransmit=9 bytes_invalid=0 send_seq=2861 receive_seq=2861 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997468 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12240 bytes_read=60233 bytes_retransmit=9 bytes_invalid=0 send_seq=1239 receive_seq=1239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999995 adj=63997309 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3307 bytes_read=100016 bytes_retransmit=9 bytes_invalid=0 send_seq=502 receive_seq=502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999513 adj=47997540 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3901 bytes_read=11535 bytes_retransmit=9 bytes_invalid=0 send_seq=497 receive_seq=497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999402 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.5 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46977 bytes_read=354356 bytes_retransmit=0 bytes_invalid=0 send_seq=4134 receive_seq=4134 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998554 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.8 th1: temp=42.4 th2: temp=43.9 th3: temp=42.1 sysload=0.12 cputime=55.789 memavail=7408964 print_time=435.835 buffer_time=2.206 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 412.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4678487 bytes_read=608640 bytes_retransmit=9 bytes_invalid=0 send_seq=84168 receive_seq=84168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=43676 freq=400015634 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3154 bytes_read=11752 bytes_retransmit=0 bytes_invalid=0 send_seq=497 receive_seq=497 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000059 adj=49997816 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=23034 bytes_read=581858 bytes_retransmit=9 bytes_invalid=0 send_seq=2872 receive_seq=2872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997510 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12246 bytes_read=60333 bytes_retransmit=9 bytes_invalid=0 send_seq=1240 receive_seq=1240 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999994 adj=63997358 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3313 bytes_read=100250 bytes_retransmit=9 bytes_invalid=0 send_seq=503 receive_seq=503 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999513 adj=47997555 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3907 bytes_read=11561 bytes_retransmit=9 bytes_invalid=0 send_seq=498 receive_seq=498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999409 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.3 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46983 bytes_read=354712 bytes_retransmit=0 bytes_invalid=0 send_seq=4135 receive_seq=4135 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999895 adj=31998564 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.011 th0: temp=43.4 th1: temp=42.8 th2: temp=43.8 th3: temp=42.0 sysload=0.12 cputime=55.936 memavail=7408964 print_time=436.911 buffer_time=2.282 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 413.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4703276 bytes_read=611009 bytes_retransmit=9 bytes_invalid=0 send_seq=84574 receive_seq=84574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=45532 freq=400015743 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3160 bytes_read=11768 bytes_retransmit=0 bytes_invalid=0 send_seq=498 receive_seq=498 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000054 adj=49997875 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=23110 bytes_read=584915 bytes_retransmit=9 bytes_invalid=0 send_seq=2883 receive_seq=2883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997577 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12252 bytes_read=60447 bytes_retransmit=9 bytes_invalid=0 send_seq=1241 receive_seq=1241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999994 adj=63997435 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3319 bytes_read=100499 bytes_retransmit=9 bytes_invalid=0 send_seq=504 receive_seq=504 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999512 adj=47997607 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3913 bytes_read=11576 bytes_retransmit=9 bytes_invalid=0 send_seq=499 receive_seq=499 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46989 bytes_read=355068 bytes_retransmit=0 bytes_invalid=0 send_seq=4136 receive_seq=4136 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999895 adj=31998605 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=43.7 th1: temp=42.7 th2: temp=43.9 th3: temp=42.1 sysload=0.12 cputime=56.085 memavail=7408964 print_time=437.988 buffer_time=2.358 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 414.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4728055 bytes_read=613339 bytes_retransmit=9 bytes_invalid=0 send_seq=84978 receive_seq=84978 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=47388 freq=400015808 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3166 bytes_read=11797 bytes_retransmit=0 bytes_invalid=0 send_seq=499 receive_seq=499 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000049 adj=49997713 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=23186 bytes_read=587999 bytes_retransmit=9 bytes_invalid=0 send_seq=2894 receive_seq=2894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997378 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12258 bytes_read=60575 bytes_retransmit=9 bytes_invalid=0 send_seq=1242 receive_seq=1242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999994 adj=63997251 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3325 bytes_read=100793 bytes_retransmit=9 bytes_invalid=0 send_seq=505 receive_seq=505 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997459 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3919 bytes_read=11591 bytes_retransmit=9 bytes_invalid=0 send_seq=500 receive_seq=500 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999389 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=46995 bytes_read=355424 bytes_retransmit=0 bytes_invalid=0 send_seq=4137 receive_seq=4137 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998509 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=43.7 th1: temp=42.8 th2: temp=43.8 th3: temp=42.1 sysload=0.12 cputime=56.232 memavail=7408964 print_time=439.064 buffer_time=2.434 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 415.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4752877 bytes_read=615705 bytes_retransmit=9 bytes_invalid=0 send_seq=85386 receive_seq=85386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=49231 freq=400015828 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3172 bytes_read=11813 bytes_retransmit=0 bytes_invalid=0 send_seq=500 receive_seq=500 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000044 adj=49997642 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=23262 bytes_read=591072 bytes_retransmit=9 bytes_invalid=0 send_seq=2905 receive_seq=2905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997313 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12264 bytes_read=60675 bytes_retransmit=9 bytes_invalid=0 send_seq=1243 receive_seq=1243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999994 adj=63997178 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3331 bytes_read=101027 bytes_retransmit=9 bytes_invalid=0 send_seq=506 receive_seq=506 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997441 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3925 bytes_read=11606 bytes_retransmit=9 bytes_invalid=0 send_seq=501 receive_seq=501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999375 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47001 bytes_read=355780 bytes_retransmit=0 bytes_invalid=0 send_seq=4138 receive_seq=4138 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998464 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=43.6 th1: temp=42.9 th2: temp=43.6 th3: temp=42.2 sysload=0.12 cputime=56.376 memavail=7407956 print_time=440.141 buffer_time=2.510 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 416.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4777639 bytes_read=618064 bytes_retransmit=9 bytes_invalid=0 send_seq=85790 receive_seq=85790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=38871 freq=400015822 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3178 bytes_read=11829 bytes_retransmit=0 bytes_invalid=0 send_seq=501 receive_seq=501 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000040 adj=49997653 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=23338 bytes_read=594129 bytes_retransmit=9 bytes_invalid=0 send_seq=2916 receive_seq=2916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997324 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12270 bytes_read=60775 bytes_retransmit=9 bytes_invalid=0 send_seq=1244 receive_seq=1244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999994 adj=63997198 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3337 bytes_read=101261 bytes_retransmit=9 bytes_invalid=0 send_seq=507 receive_seq=507 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999514 adj=47997442 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3931 bytes_read=11621 bytes_retransmit=9 bytes_invalid=0 send_seq=502 receive_seq=502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999380 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47007 bytes_read=356136 bytes_retransmit=0 bytes_invalid=0 send_seq=4139 receive_seq=4139 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998473 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=43.5 th1: temp=43.1 th2: temp=44.0 th3: temp=42.1 sysload=0.11 cputime=56.509 memavail=7407956 print_time=440.679 buffer_time=2.047 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 417.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4802764 bytes_read=620434 bytes_retransmit=9 bytes_invalid=0 send_seq=86202 receive_seq=86202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400015801 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3184 bytes_read=11845 bytes_retransmit=0 bytes_invalid=0 send_seq=502 receive_seq=502 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000036 adj=49997613 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=23414 bytes_read=597213 bytes_retransmit=9 bytes_invalid=0 send_seq=2927 receive_seq=2927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997315 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12276 bytes_read=60903 bytes_retransmit=9 bytes_invalid=0 send_seq=1245 receive_seq=1245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999999 adj=63997208 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3343 bytes_read=101555 bytes_retransmit=9 bytes_invalid=0 send_seq=508 receive_seq=508 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999513 adj=47997445 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3937 bytes_read=11647 bytes_retransmit=9 bytes_invalid=0 send_seq=503 receive_seq=503 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999381 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=29.6 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47013 bytes_read=356492 bytes_retransmit=0 bytes_invalid=0 send_seq=4140 receive_seq=4140 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999892 adj=31998477 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.6 th1: temp=42.8 th2: temp=43.8 th3: temp=42.1 sysload=0.11 cputime=56.660 memavail=7407956 print_time=441.756 buffer_time=2.123 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 418.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4828242 bytes_read=622820 bytes_retransmit=9 bytes_invalid=0 send_seq=86618 receive_seq=86618 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=41655 freq=400015777 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3190 bytes_read=11861 bytes_retransmit=0 bytes_invalid=0 send_seq=503 receive_seq=503 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000031 adj=49997646 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=23490 bytes_read=600271 bytes_retransmit=9 bytes_invalid=0 send_seq=2938 receive_seq=2938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997730 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12282 bytes_read=61017 bytes_retransmit=9 bytes_invalid=0 send_seq=1246 receive_seq=1246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999999 adj=63997348 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3349 bytes_read=101804 bytes_retransmit=9 bytes_invalid=0 send_seq=509 receive_seq=509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999513 adj=47997488 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3943 bytes_read=11662 bytes_retransmit=9 bytes_invalid=0 send_seq=504 receive_seq=504 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999395 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47019 bytes_read=356848 bytes_retransmit=0 bytes_invalid=0 send_seq=4141 receive_seq=4141 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999892 adj=31998506 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.0 th1: temp=43.0 th2: temp=44.0 th3: temp=42.4 sysload=0.11 cputime=56.812 memavail=7407956 print_time=442.832 buffer_time=2.199 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 419.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4853047 bytes_read=625204 bytes_retransmit=9 bytes_invalid=0 send_seq=87025 receive_seq=87025 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=43542 freq=400015757 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3202 bytes_read=11906 bytes_retransmit=0 bytes_invalid=0 send_seq=505 receive_seq=505 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000020 adj=49997719 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=23572 bytes_read=603401 bytes_retransmit=9 bytes_invalid=0 send_seq=2950 receive_seq=2950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997736 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12294 bytes_read=61133 bytes_retransmit=9 bytes_invalid=0 send_seq=1248 receive_seq=1248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000016 adj=63997417 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3361 bytes_read=102054 bytes_retransmit=9 bytes_invalid=0 send_seq=511 receive_seq=511 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999512 adj=47997548 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3955 bytes_read=11692 bytes_retransmit=9 bytes_invalid=0 send_seq=506 receive_seq=506 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999411 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47031 bytes_read=357220 bytes_retransmit=0 bytes_invalid=0 send_seq=4143 receive_seq=4143 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999892 adj=31998558 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=44.0 th1: temp=42.8 th2: temp=43.8 th3: temp=42.1 sysload=0.11 cputime=56.965 memavail=7407968 print_time=443.908 buffer_time=2.275 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 420.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4877759 bytes_read=627510 bytes_retransmit=9 bytes_invalid=0 send_seq=87421 receive_seq=87421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=33154 freq=400015736 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3208 bytes_read=11922 bytes_retransmit=0 bytes_invalid=0 send_seq=506 receive_seq=506 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000016 adj=49997701 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=23648 bytes_read=606504 bytes_retransmit=9 bytes_invalid=0 send_seq=2961 receive_seq=2961 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997712 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12300 bytes_read=61261 bytes_retransmit=9 bytes_invalid=0 send_seq=1249 receive_seq=1249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000013 adj=63997665 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3367 bytes_read=102348 bytes_retransmit=9 bytes_invalid=0 send_seq=512 receive_seq=512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997580 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3961 bytes_read=11707 bytes_retransmit=9 bytes_invalid=0 send_seq=507 receive_seq=507 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.5 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47037 bytes_read=357576 bytes_retransmit=0 bytes_invalid=0 send_seq=4144 receive_seq=4144 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999891 adj=31998591 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.7 th1: temp=42.8 th2: temp=43.9 th3: temp=42.2 sysload=0.11 cputime=57.107 memavail=7407968 print_time=444.985 buffer_time=2.351 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 421.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4902583 bytes_read=629860 bytes_retransmit=9 bytes_invalid=0 send_seq=87829 receive_seq=87829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=22820 freq=400015723 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3214 bytes_read=11938 bytes_retransmit=0 bytes_invalid=0 send_seq=507 receive_seq=507 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000012 adj=49997753 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=23717 bytes_read=609540 bytes_retransmit=9 bytes_invalid=0 send_seq=2971 receive_seq=2971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997706 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12306 bytes_read=61361 bytes_retransmit=9 bytes_invalid=0 send_seq=1250 receive_seq=1250 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000013 adj=63997642 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3373 bytes_read=102582 bytes_retransmit=9 bytes_invalid=0 send_seq=513 receive_seq=513 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997610 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3967 bytes_read=11722 bytes_retransmit=9 bytes_invalid=0 send_seq=508 receive_seq=508 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.4 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47043 bytes_read=357932 bytes_retransmit=0 bytes_invalid=0 send_seq=4145 receive_seq=4145 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999891 adj=31998612 coil_temp=17.6 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=44.3 th1: temp=42.9 th2: temp=43.9 th3: temp=42.3 sysload=0.10 cputime=57.253 memavail=7407720 print_time=446.061 buffer_time=2.427 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 422.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4918782 bytes_read=631539 bytes_retransmit=9 bytes_invalid=0 send_seq=88097 receive_seq=88097 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=20367 freq=400015706 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3220 bytes_read=11954 bytes_retransmit=0 bytes_invalid=0 send_seq=508 receive_seq=508 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000007 adj=49997789 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=23793 bytes_read=612596 bytes_retransmit=9 bytes_invalid=0 send_seq=2982 receive_seq=2982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997701 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12312 bytes_read=61461 bytes_retransmit=9 bytes_invalid=0 send_seq=1251 receive_seq=1251 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000011 adj=63997626 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3379 bytes_read=102816 bytes_retransmit=9 bytes_invalid=0 send_seq=514 receive_seq=514 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3973 bytes_read=11748 bytes_retransmit=9 bytes_invalid=0 send_seq=509 receive_seq=509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.4 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47049 bytes_read=358288 bytes_retransmit=0 bytes_invalid=0 send_seq=4146 receive_seq=4146 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999890 adj=31998622 coil_temp=17.6 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=44.0 th1: temp=42.7 th2: temp=44.1 th3: temp=42.3 sysload=0.10 cputime=57.383 memavail=7407764 print_time=447.138 buffer_time=2.503 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 423.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4931281 bytes_read=632894 bytes_retransmit=9 bytes_invalid=0 send_seq=88306 receive_seq=88306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=15171 freq=400015690 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3226 bytes_read=11970 bytes_retransmit=0 bytes_invalid=0 send_seq=509 receive_seq=509 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=50000002 adj=49997814 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=23869 bytes_read=615683 bytes_retransmit=9 bytes_invalid=0 send_seq=2993 receive_seq=2993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997696 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12318 bytes_read=61603 bytes_retransmit=9 bytes_invalid=0 send_seq=1252 receive_seq=1252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000010 adj=63997611 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3385 bytes_read=103121 bytes_retransmit=9 bytes_invalid=0 send_seq=515 receive_seq=515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997682 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3979 bytes_read=11763 bytes_retransmit=9 bytes_invalid=0 send_seq=510 receive_seq=510 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.6 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47055 bytes_read=358644 bytes_retransmit=0 bytes_invalid=0 send_seq=4147 receive_seq=4147 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999890 adj=31998632 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.8 th1: temp=42.4 th2: temp=44.0 th3: temp=42.3 sysload=0.10 cputime=57.503 memavail=7407764 print_time=447.676 buffer_time=2.040 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 424.2: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4943864 bytes_read=634274 bytes_retransmit=9 bytes_invalid=0 send_seq=88520 receive_seq=88520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=16049 freq=400015667 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3232 bytes_read=11999 bytes_retransmit=0 bytes_invalid=0 send_seq=510 receive_seq=510 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999997 adj=49997782 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=23945 bytes_read=618739 bytes_retransmit=9 bytes_invalid=0 send_seq=3004 receive_seq=3004 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997695 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12324 bytes_read=61703 bytes_retransmit=9 bytes_invalid=0 send_seq=1253 receive_seq=1253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000008 adj=63997626 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3391 bytes_read=103339 bytes_retransmit=9 bytes_invalid=0 send_seq=516 receive_seq=516 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997712 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3985 bytes_read=11779 bytes_retransmit=9 bytes_invalid=0 send_seq=511 receive_seq=511 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47061 bytes_read=359000 bytes_retransmit=0 bytes_invalid=0 send_seq=4148 receive_seq=4148 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999889 adj=31998643 coil_temp=17.6 refs=0 mcu_temp=20.76 supply_voltage=3.012 th0: temp=43.9 th1: temp=42.8 th2: temp=43.9 th3: temp=42.4 sysload=0.10 cputime=57.648 memavail=7407356 print_time=448.753 buffer_time=2.116 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 425.2: gcodein=0  mcu: mcu_awake=0.015 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4956802 bytes_read=635674 bytes_retransmit=9 bytes_invalid=0 send_seq=88729 receive_seq=88729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=16563 freq=400015651 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3238 bytes_read=12015 bytes_retransmit=0 bytes_invalid=0 send_seq=511 receive_seq=511 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999991 adj=49997782 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=24021 bytes_read=621814 bytes_retransmit=9 bytes_invalid=0 send_seq=3015 receive_seq=3015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997708 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12330 bytes_read=61803 bytes_retransmit=9 bytes_invalid=0 send_seq=1254 receive_seq=1254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997639 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3397 bytes_read=103556 bytes_retransmit=9 bytes_invalid=0 send_seq=517 receive_seq=517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997726 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3991 bytes_read=11795 bytes_retransmit=9 bytes_invalid=0 send_seq=512 receive_seq=512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47067 bytes_read=359356 bytes_retransmit=0 bytes_invalid=0 send_seq=4149 receive_seq=4149 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999889 adj=31998655 coil_temp=17.6 refs=0 mcu_temp=20.76 supply_voltage=3.012 th0: temp=44.2 th1: temp=42.9 th2: temp=44.1 th3: temp=42.0 sysload=0.10 cputime=57.782 memavail=7406896 print_time=449.829 buffer_time=2.192 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 426.2: gcodein=0  mcu: mcu_awake=0.015 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4969316 bytes_read=637034 bytes_retransmit=9 bytes_invalid=0 send_seq=88939 receive_seq=88939 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=17507 freq=400015669 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3244 bytes_read=12031 bytes_retransmit=0 bytes_invalid=0 send_seq=512 receive_seq=512 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999988 adj=49997798 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=24097 bytes_read=624898 bytes_retransmit=9 bytes_invalid=0 send_seq=3026 receive_seq=3026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997724 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12336 bytes_read=61931 bytes_retransmit=9 bytes_invalid=0 send_seq=1255 receive_seq=1255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997627 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3403 bytes_read=103830 bytes_retransmit=9 bytes_invalid=0 send_seq=518 receive_seq=518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997764 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=3997 bytes_read=11811 bytes_retransmit=9 bytes_invalid=0 send_seq=513 receive_seq=513 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47073 bytes_read=359712 bytes_retransmit=0 bytes_invalid=0 send_seq=4150 receive_seq=4150 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999888 adj=31998664 coil_temp=17.6 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=43.9 th1: temp=42.5 th2: temp=43.9 th3: temp=42.2 sysload=0.09 cputime=57.915 memavail=7406896 print_time=450.905 buffer_time=2.269 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 427.2: gcodein=0  mcu: mcu_awake=0.015 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4981831 bytes_read=638399 bytes_retransmit=9 bytes_invalid=0 send_seq=89150 receive_seq=89150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=18429 freq=400015650 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3250 bytes_read=12047 bytes_retransmit=0 bytes_invalid=0 send_seq=513 receive_seq=513 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999983 adj=49997790 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=24173 bytes_read=628012 bytes_retransmit=9 bytes_invalid=0 send_seq=3037 receive_seq=3037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997669 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12342 bytes_read=62031 bytes_retransmit=9 bytes_invalid=0 send_seq=1256 receive_seq=1256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000012 adj=63997555 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3409 bytes_read=104048 bytes_retransmit=9 bytes_invalid=0 send_seq=519 receive_seq=519 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997702 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4003 bytes_read=11838 bytes_retransmit=9 bytes_invalid=0 send_seq=514 receive_seq=514 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47079 bytes_read=360068 bytes_retransmit=0 bytes_invalid=0 send_seq=4151 receive_seq=4151 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999888 adj=31998632 coil_temp=17.6 refs=0 mcu_temp=20.76 supply_voltage=3.012 th0: temp=43.9 th1: temp=42.9 th2: temp=43.8 th3: temp=42.3 sysload=0.09 cputime=58.047 memavail=7406896 print_time=451.982 buffer_time=2.345 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 428.2: gcodein=0  mcu: mcu_awake=0.015 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=4994403 bytes_read=639796 bytes_retransmit=9 bytes_invalid=0 send_seq=89362 receive_seq=89362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=19340 freq=400015639 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3256 bytes_read=12063 bytes_retransmit=0 bytes_invalid=0 send_seq=514 receive_seq=514 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999978 adj=49997812 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=24249 bytes_read=631070 bytes_retransmit=9 bytes_invalid=0 send_seq=3048 receive_seq=3048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997678 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12348 bytes_read=62145 bytes_retransmit=9 bytes_invalid=0 send_seq=1257 receive_seq=1257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000010 adj=63997636 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3415 bytes_read=104281 bytes_retransmit=9 bytes_invalid=0 send_seq=520 receive_seq=520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997704 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4009 bytes_read=11854 bytes_retransmit=9 bytes_invalid=0 send_seq=515 receive_seq=515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47085 bytes_read=360424 bytes_retransmit=0 bytes_invalid=0 send_seq=4152 receive_seq=4152 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999888 adj=31998654 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.0 th1: temp=42.6 th2: temp=44.0 th3: temp=42.2 sysload=0.09 cputime=58.174 memavail=7406400 print_time=453.058 buffer_time=2.420 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 429.2: gcodein=0  mcu: mcu_awake=0.015 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5006918 bytes_read=641162 bytes_retransmit=9 bytes_invalid=0 send_seq=89574 receive_seq=89574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=20268 freq=400015612 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3262 bytes_read=12092 bytes_retransmit=0 bytes_invalid=0 send_seq=515 receive_seq=515 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999973 adj=49997818 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=24325 bytes_read=634156 bytes_retransmit=9 bytes_invalid=0 send_seq=3059 receive_seq=3059 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997868 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12354 bytes_read=62273 bytes_retransmit=9 bytes_invalid=0 send_seq=1258 receive_seq=1258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000008 adj=63997610 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3421 bytes_read=104571 bytes_retransmit=9 bytes_invalid=0 send_seq=521 receive_seq=521 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999514 adj=47997694 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4015 bytes_read=11870 bytes_retransmit=9 bytes_invalid=0 send_seq=516 receive_seq=516 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47091 bytes_read=360780 bytes_retransmit=0 bytes_invalid=0 send_seq=4153 receive_seq=4153 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998651 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=44.3 th1: temp=42.9 th2: temp=43.8 th3: temp=42.3 sysload=0.09 cputime=58.308 memavail=7406404 print_time=454.135 buffer_time=2.496 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 430.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5019458 bytes_read=642548 bytes_retransmit=9 bytes_invalid=0 send_seq=89786 receive_seq=89786 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=15088 freq=400015587 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3268 bytes_read=12108 bytes_retransmit=0 bytes_invalid=0 send_seq=516 receive_seq=516 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999967 adj=49997836 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=24401 bytes_read=637230 bytes_retransmit=9 bytes_invalid=0 send_seq=3070 receive_seq=3070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997858 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12360 bytes_read=62373 bytes_retransmit=9 bytes_invalid=0 send_seq=1259 receive_seq=1259 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000008 adj=63997621 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3427 bytes_read=104805 bytes_retransmit=9 bytes_invalid=0 send_seq=522 receive_seq=522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999513 adj=47997710 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4021 bytes_read=11886 bytes_retransmit=9 bytes_invalid=0 send_seq=517 receive_seq=517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47097 bytes_read=361136 bytes_retransmit=0 bytes_invalid=0 send_seq=4154 receive_seq=4154 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998742 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.2 th1: temp=42.9 th2: temp=44.0 th3: temp=42.3 sysload=0.09 cputime=58.426 memavail=7406404 print_time=454.673 buffer_time=2.034 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 431.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5031966 bytes_read=643942 bytes_retransmit=9 bytes_invalid=0 send_seq=89997 receive_seq=89997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=16033 freq=400015581 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3274 bytes_read=12124 bytes_retransmit=0 bytes_invalid=0 send_seq=517 receive_seq=517 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999963 adj=49997808 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=24477 bytes_read=640290 bytes_retransmit=9 bytes_invalid=0 send_seq=3081 receive_seq=3081 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997882 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12366 bytes_read=62473 bytes_retransmit=9 bytes_invalid=0 send_seq=1260 receive_seq=1260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997655 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3433 bytes_read=105039 bytes_retransmit=9 bytes_invalid=0 send_seq=523 receive_seq=523 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997734 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4027 bytes_read=11902 bytes_retransmit=9 bytes_invalid=0 send_seq=518 receive_seq=518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47103 bytes_read=361492 bytes_retransmit=0 bytes_invalid=0 send_seq=4155 receive_seq=4155 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998751 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.9 th1: temp=42.9 th2: temp=44.1 th3: temp=42.2 sysload=0.08 cputime=58.558 memavail=7406404 print_time=455.750 buffer_time=2.110 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 432.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5044980 bytes_read=645347 bytes_retransmit=9 bytes_invalid=0 send_seq=90216 receive_seq=90216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=16480 freq=400015561 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3280 bytes_read=12140 bytes_retransmit=0 bytes_invalid=0 send_seq=518 receive_seq=518 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999957 adj=49997788 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=24553 bytes_read=643375 bytes_retransmit=9 bytes_invalid=0 send_seq=3092 receive_seq=3092 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997838 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12372 bytes_read=62601 bytes_retransmit=9 bytes_invalid=0 send_seq=1261 receive_seq=1261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997641 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3439 bytes_read=105333 bytes_retransmit=9 bytes_invalid=0 send_seq=524 receive_seq=524 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997809 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4033 bytes_read=11929 bytes_retransmit=9 bytes_invalid=0 send_seq=519 receive_seq=519 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47109 bytes_read=361848 bytes_retransmit=0 bytes_invalid=0 send_seq=4156 receive_seq=4156 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999892 adj=31998740 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=43.8 th1: temp=43.1 th2: temp=44.4 th3: temp=42.4 sysload=0.08 cputime=58.691 memavail=7406404 print_time=456.826 buffer_time=2.185 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 433.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5057541 bytes_read=646722 bytes_retransmit=9 bytes_invalid=0 send_seq=90429 receive_seq=90429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=17408 freq=400015546 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3286 bytes_read=12156 bytes_retransmit=0 bytes_invalid=0 send_seq=519 receive_seq=519 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999951 adj=49997796 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=24622 bytes_read=646409 bytes_retransmit=9 bytes_invalid=0 send_seq=3102 receive_seq=3102 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997893 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12378 bytes_read=62715 bytes_retransmit=9 bytes_invalid=0 send_seq=1262 receive_seq=1262 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997632 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3445 bytes_read=105582 bytes_retransmit=9 bytes_invalid=0 send_seq=525 receive_seq=525 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997784 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4039 bytes_read=11945 bytes_retransmit=9 bytes_invalid=0 send_seq=520 receive_seq=520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.6 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47115 bytes_read=362204 bytes_retransmit=0 bytes_invalid=0 send_seq=4157 receive_seq=4157 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999892 adj=31998733 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=43.8 th1: temp=43.0 th2: temp=44.2 th3: temp=42.4 sysload=0.08 cputime=58.820 memavail=7406404 print_time=457.903 buffer_time=2.261 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 434.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5070057 bytes_read=648116 bytes_retransmit=9 bytes_invalid=0 send_seq=90640 receive_seq=90640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=18331 freq=400015586 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3292 bytes_read=12185 bytes_retransmit=0 bytes_invalid=0 send_seq=520 receive_seq=520 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999947 adj=49997808 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=24698 bytes_read=649524 bytes_retransmit=9 bytes_invalid=0 send_seq=3113 receive_seq=3113 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997848 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12384 bytes_read=62815 bytes_retransmit=9 bytes_invalid=0 send_seq=1263 receive_seq=1263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997630 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3451 bytes_read=105816 bytes_retransmit=9 bytes_invalid=0 send_seq=526 receive_seq=526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997764 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4045 bytes_read=11961 bytes_retransmit=9 bytes_invalid=0 send_seq=521 receive_seq=521 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999462 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47121 bytes_read=362560 bytes_retransmit=0 bytes_invalid=0 send_seq=4158 receive_seq=4158 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999891 adj=31998722 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.011 th0: temp=43.9 th1: temp=43.1 th2: temp=43.9 th3: temp=42.6 sysload=0.08 cputime=58.951 memavail=7406404 print_time=458.979 buffer_time=2.337 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 435.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5082643 bytes_read=649507 bytes_retransmit=9 bytes_invalid=0 send_seq=90853 receive_seq=90853 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=19241 freq=400015582 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3298 bytes_read=12201 bytes_retransmit=0 bytes_invalid=0 send_seq=521 receive_seq=521 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999942 adj=49997740 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=24774 bytes_read=652627 bytes_retransmit=9 bytes_invalid=0 send_seq=3124 receive_seq=3124 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997749 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12390 bytes_read=62943 bytes_retransmit=9 bytes_invalid=0 send_seq=1264 receive_seq=1264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997518 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3457 bytes_read=106110 bytes_retransmit=9 bytes_invalid=0 send_seq=527 receive_seq=527 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4051 bytes_read=11977 bytes_retransmit=9 bytes_invalid=0 send_seq=522 receive_seq=522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47127 bytes_read=362916 bytes_retransmit=0 bytes_invalid=0 send_seq=4159 receive_seq=4159 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998660 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.011 th0: temp=43.9 th1: temp=43.1 th2: temp=43.9 th3: temp=42.2 sysload=0.08 cputime=59.091 memavail=7409344 print_time=460.055 buffer_time=2.413 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 436.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5095133 bytes_read=650877 bytes_retransmit=9 bytes_invalid=0 send_seq=91065 receive_seq=91065 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=20185 freq=400015561 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3304 bytes_read=12217 bytes_retransmit=0 bytes_invalid=0 send_seq=522 receive_seq=522 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999937 adj=49997746 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=24850 bytes_read=655685 bytes_retransmit=9 bytes_invalid=0 send_seq=3135 receive_seq=3135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997734 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12396 bytes_read=63043 bytes_retransmit=9 bytes_invalid=0 send_seq=1265 receive_seq=1265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000001 adj=63997512 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3463 bytes_read=106344 bytes_retransmit=9 bytes_invalid=0 send_seq=528 receive_seq=528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4057 bytes_read=11993 bytes_retransmit=9 bytes_invalid=0 send_seq=523 receive_seq=523 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47133 bytes_read=363272 bytes_retransmit=0 bytes_invalid=0 send_seq=4160 receive_seq=4160 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999892 adj=31998681 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=44.0 th1: temp=43.2 th2: temp=44.1 th3: temp=42.2 sysload=0.16 cputime=59.220 memavail=7409344 print_time=461.132 buffer_time=2.489 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 437.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5107691 bytes_read=652271 bytes_retransmit=9 bytes_invalid=0 send_seq=91276 receive_seq=91276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=14989 freq=400015558 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3310 bytes_read=12233 bytes_retransmit=0 bytes_invalid=0 send_seq=523 receive_seq=523 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999932 adj=49997767 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=24926 bytes_read=658743 bytes_retransmit=9 bytes_invalid=0 send_seq=3146 receive_seq=3146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997851 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12402 bytes_read=63143 bytes_retransmit=9 bytes_invalid=0 send_seq=1266 receive_seq=1266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000001 adj=63997536 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3469 bytes_read=106578 bytes_retransmit=9 bytes_invalid=0 send_seq=529 receive_seq=529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999514 adj=47997682 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4063 bytes_read=12020 bytes_retransmit=9 bytes_invalid=0 send_seq=524 receive_seq=524 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47139 bytes_read=363628 bytes_retransmit=0 bytes_invalid=0 send_seq=4161 receive_seq=4161 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999891 adj=31998683 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=44.1 th1: temp=43.0 th2: temp=43.9 th3: temp=42.2 sysload=0.16 cputime=59.340 memavail=7409092 print_time=461.670 buffer_time=2.026 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 438.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5120226 bytes_read=653636 bytes_retransmit=9 bytes_invalid=0 send_seq=91487 receive_seq=91487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=15933 freq=400015560 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3316 bytes_read=12248 bytes_retransmit=0 bytes_invalid=0 send_seq=524 receive_seq=524 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999926 adj=49997714 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=25002 bytes_read=661829 bytes_retransmit=9 bytes_invalid=0 send_seq=3157 receive_seq=3157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997908 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12408 bytes_read=63285 bytes_retransmit=9 bytes_invalid=0 send_seq=1267 receive_seq=1267 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000001 adj=63997536 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3475 bytes_read=106887 bytes_retransmit=9 bytes_invalid=0 send_seq=530 receive_seq=530 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999514 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4069 bytes_read=12036 bytes_retransmit=9 bytes_invalid=0 send_seq=525 receive_seq=525 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47145 bytes_read=363984 bytes_retransmit=0 bytes_invalid=0 send_seq=4162 receive_seq=4162 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999891 adj=31998678 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=44.2 th1: temp=43.2 th2: temp=43.9 th3: temp=42.1 sysload=0.16 cputime=59.472 memavail=7409092 print_time=462.747 buffer_time=2.102 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 439.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5133256 bytes_read=655039 bytes_retransmit=9 bytes_invalid=0 send_seq=91706 receive_seq=91706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=16381 freq=400015556 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=3322 bytes_read=12276 bytes_retransmit=0 bytes_invalid=0 send_seq=525 receive_seq=525 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999921 adj=49997681 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=25078 bytes_read=664885 bytes_retransmit=9 bytes_invalid=0 send_seq=3168 receive_seq=3168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997832 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12414 bytes_read=63385 bytes_retransmit=9 bytes_invalid=0 send_seq=1268 receive_seq=1268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000002 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3481 bytes_read=107121 bytes_retransmit=9 bytes_invalid=0 send_seq=531 receive_seq=531 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4075 bytes_read=12052 bytes_retransmit=9 bytes_invalid=0 send_seq=526 receive_seq=526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47151 bytes_read=364340 bytes_retransmit=0 bytes_invalid=0 send_seq=4163 receive_seq=4163 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999891 adj=31998663 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=44.0 th1: temp=43.0 th2: temp=44.2 th3: temp=42.3 sysload=0.16 cputime=59.606 memavail=7408840 print_time=463.823 buffer_time=2.178 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 440.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5145773 bytes_read=656447 bytes_retransmit=9 bytes_invalid=0 send_seq=91917 receive_seq=91917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=17309 freq=400015552 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=3328 bytes_read=12291 bytes_retransmit=0 bytes_invalid=0 send_seq=526 receive_seq=526 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999916 adj=49997697 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=25154 bytes_read=667959 bytes_retransmit=9 bytes_invalid=0 send_seq=3179 receive_seq=3179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997774 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12420 bytes_read=63485 bytes_retransmit=9 bytes_invalid=0 send_seq=1269 receive_seq=1269 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000002 adj=63997545 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3487 bytes_read=107355 bytes_retransmit=9 bytes_invalid=0 send_seq=532 receive_seq=532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997693 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4081 bytes_read=12068 bytes_retransmit=9 bytes_invalid=0 send_seq=527 receive_seq=527 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.4 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47157 bytes_read=364696 bytes_retransmit=0 bytes_invalid=0 send_seq=4164 receive_seq=4164 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999890 adj=31998663 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=44.2 th1: temp=42.8 th2: temp=44.2 th3: temp=42.4 sysload=0.16 cputime=59.736 memavail=7408844 print_time=464.900 buffer_time=2.254 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 441.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5158285 bytes_read=657812 bytes_retransmit=9 bytes_invalid=0 send_seq=92128 receive_seq=92128 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=18237 freq=400015547 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=3334 bytes_read=12306 bytes_retransmit=0 bytes_invalid=0 send_seq=527 receive_seq=527 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999911 adj=49997704 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=25230 bytes_read=671101 bytes_retransmit=9 bytes_invalid=0 send_seq=3190 receive_seq=3190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997738 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12426 bytes_read=63613 bytes_retransmit=9 bytes_invalid=0 send_seq=1270 receive_seq=1270 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000002 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3493 bytes_read=107649 bytes_retransmit=9 bytes_invalid=0 send_seq=533 receive_seq=533 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997682 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4087 bytes_read=12084 bytes_retransmit=9 bytes_invalid=0 send_seq=528 receive_seq=528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.6 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47163 bytes_read=365052 bytes_retransmit=0 bytes_invalid=0 send_seq=4165 receive_seq=4165 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998658 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=43.9 th1: temp=42.8 th2: temp=44.1 th3: temp=42.5 sysload=0.15 cputime=59.880 memavail=7409492 print_time=465.976 buffer_time=2.330 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 442.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5170814 bytes_read=659167 bytes_retransmit=9 bytes_invalid=0 send_seq=92337 receive_seq=92337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=19158 freq=400015572 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=3340 bytes_read=12321 bytes_retransmit=0 bytes_invalid=0 send_seq=528 receive_seq=528 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999906 adj=49997713 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=25306 bytes_read=674159 bytes_retransmit=9 bytes_invalid=0 send_seq=3201 receive_seq=3201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997703 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12432 bytes_read=63713 bytes_retransmit=9 bytes_invalid=0 send_seq=1271 receive_seq=1271 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000002 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3499 bytes_read=107883 bytes_retransmit=9 bytes_invalid=0 send_seq=534 receive_seq=534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999514 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4093 bytes_read=12111 bytes_retransmit=9 bytes_invalid=0 send_seq=529 receive_seq=529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47169 bytes_read=365408 bytes_retransmit=0 bytes_invalid=0 send_seq=4166 receive_seq=4166 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998728 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=44.2 th1: temp=43.0 th2: temp=44.1 th3: temp=42.3 sysload=0.15 cputime=60.012 memavail=7409492 print_time=467.053 buffer_time=2.406 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 443.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5183326 bytes_read=660556 bytes_retransmit=9 bytes_invalid=0 send_seq=92547 receive_seq=92547 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=20086 freq=400015565 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=3346 bytes_read=12337 bytes_retransmit=0 bytes_invalid=0 send_seq=529 receive_seq=529 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999901 adj=49997669 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=25382 bytes_read=677215 bytes_retransmit=9 bytes_invalid=0 send_seq=3212 receive_seq=3212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997747 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12438 bytes_read=63827 bytes_retransmit=9 bytes_invalid=0 send_seq=1272 receive_seq=1272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000002 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3505 bytes_read=108132 bytes_retransmit=9 bytes_invalid=0 send_seq=535 receive_seq=535 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999514 adj=47997632 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4099 bytes_read=12127 bytes_retransmit=9 bytes_invalid=0 send_seq=530 receive_seq=530 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47175 bytes_read=365764 bytes_retransmit=0 bytes_invalid=0 send_seq=4167 receive_seq=4167 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999895 adj=31998683 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.011 th0: temp=44.2 th1: temp=43.4 th2: temp=44.0 th3: temp=42.6 sysload=0.15 cputime=60.142 memavail=7409492 print_time=468.129 buffer_time=2.481 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 444.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5195901 bytes_read=661936 bytes_retransmit=9 bytes_invalid=0 send_seq=92761 receive_seq=92761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=14906 freq=400015585 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3352 bytes_read=12366 bytes_retransmit=0 bytes_invalid=0 send_seq=530 receive_seq=530 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999896 adj=49997683 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=25458 bytes_read=680300 bytes_retransmit=9 bytes_invalid=0 send_seq=3223 receive_seq=3223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997738 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12444 bytes_read=63955 bytes_retransmit=9 bytes_invalid=0 send_seq=1273 receive_seq=1273 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000001 adj=63997508 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3511 bytes_read=108426 bytes_retransmit=9 bytes_invalid=0 send_seq=536 receive_seq=536 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999514 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4105 bytes_read=12143 bytes_retransmit=9 bytes_invalid=0 send_seq=531 receive_seq=531 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47181 bytes_read=366120 bytes_retransmit=0 bytes_invalid=0 send_seq=4168 receive_seq=4168 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998675 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.011 th0: temp=44.2 th1: temp=43.2 th2: temp=44.1 th3: temp=42.4 sysload=0.15 cputime=60.262 memavail=7409504 print_time=468.667 buffer_time=2.019 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 445.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5208388 bytes_read=663326 bytes_retransmit=9 bytes_invalid=0 send_seq=92971 receive_seq=92971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=15834 freq=400015582 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3358 bytes_read=12382 bytes_retransmit=0 bytes_invalid=0 send_seq=531 receive_seq=531 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999890 adj=49997601 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=25527 bytes_read=683350 bytes_retransmit=9 bytes_invalid=0 send_seq=3233 receive_seq=3233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997665 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12450 bytes_read=64055 bytes_retransmit=9 bytes_invalid=0 send_seq=1274 receive_seq=1274 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997460 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3517 bytes_read=108660 bytes_retransmit=9 bytes_invalid=0 send_seq=537 receive_seq=537 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997611 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4111 bytes_read=12159 bytes_retransmit=9 bytes_invalid=0 send_seq=532 receive_seq=532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47187 bytes_read=366476 bytes_retransmit=0 bytes_invalid=0 send_seq=4169 receive_seq=4169 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998648 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.2 th1: temp=43.2 th2: temp=44.0 th3: temp=42.3 sysload=0.15 cputime=60.392 memavail=7409040 print_time=469.744 buffer_time=2.095 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 446.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5221408 bytes_read=664736 bytes_retransmit=9 bytes_invalid=0 send_seq=93188 receive_seq=93188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=26 upcoming_bytes=16314 freq=400015576 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3364 bytes_read=12398 bytes_retransmit=0 bytes_invalid=0 send_seq=532 receive_seq=532 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999885 adj=49997574 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=25603 bytes_read=686400 bytes_retransmit=9 bytes_invalid=0 send_seq=3244 receive_seq=3244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997741 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12456 bytes_read=64151 bytes_retransmit=9 bytes_invalid=0 send_seq=1275 receive_seq=1275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997571 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3523 bytes_read=108894 bytes_retransmit=9 bytes_invalid=0 send_seq=538 receive_seq=538 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4117 bytes_read=12175 bytes_retransmit=9 bytes_invalid=0 send_seq=533 receive_seq=533 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47193 bytes_read=366832 bytes_retransmit=0 bytes_invalid=0 send_seq=4170 receive_seq=4170 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998645 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.2 th1: temp=43.4 th2: temp=44.0 th3: temp=42.5 sysload=0.21 cputime=60.524 memavail=7409040 print_time=470.820 buffer_time=2.171 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 447.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5233939 bytes_read=666106 bytes_retransmit=9 bytes_invalid=0 send_seq=93400 receive_seq=93400 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=17226 freq=400015591 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3370 bytes_read=12414 bytes_retransmit=0 bytes_invalid=0 send_seq=533 receive_seq=533 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999880 adj=49997607 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=25679 bytes_read=689466 bytes_retransmit=9 bytes_invalid=0 send_seq=3255 receive_seq=3255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997709 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12462 bytes_read=64270 bytes_retransmit=9 bytes_invalid=0 send_seq=1276 receive_seq=1276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000008 adj=63997574 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3529 bytes_read=109188 bytes_retransmit=9 bytes_invalid=0 send_seq=539 receive_seq=539 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4123 bytes_read=12202 bytes_retransmit=9 bytes_invalid=0 send_seq=534 receive_seq=534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47199 bytes_read=367188 bytes_retransmit=0 bytes_invalid=0 send_seq=4171 receive_seq=4171 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999892 adj=31998642 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.2 th1: temp=43.0 th2: temp=44.2 th3: temp=42.4 sysload=0.21 cputime=60.656 memavail=7409040 print_time=471.897 buffer_time=2.246 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 448.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5246420 bytes_read=667440 bytes_retransmit=9 bytes_invalid=0 send_seq=93602 receive_seq=93602 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=18154 freq=400015585 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3376 bytes_read=12430 bytes_retransmit=0 bytes_invalid=0 send_seq=534 receive_seq=534 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999875 adj=49997599 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=25755 bytes_read=692508 bytes_retransmit=9 bytes_invalid=0 send_seq=3266 receive_seq=3266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997665 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12468 bytes_read=64377 bytes_retransmit=9 bytes_invalid=0 send_seq=1277 receive_seq=1277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000008 adj=63997522 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3535 bytes_read=109437 bytes_retransmit=9 bytes_invalid=0 send_seq=540 receive_seq=540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999514 adj=47997617 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4129 bytes_read=12218 bytes_retransmit=9 bytes_invalid=0 send_seq=535 receive_seq=535 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.6 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47205 bytes_read=367544 bytes_retransmit=0 bytes_invalid=0 send_seq=4172 receive_seq=4172 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998622 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.011 th0: temp=44.3 th1: temp=43.1 th2: temp=44.0 th3: temp=42.5 sysload=0.21 cputime=60.786 memavail=7409040 print_time=472.973 buffer_time=2.322 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 449.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5259005 bytes_read=668830 bytes_retransmit=9 bytes_invalid=0 send_seq=93815 receive_seq=93815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=19058 freq=400015580 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3382 bytes_read=12459 bytes_retransmit=0 bytes_invalid=0 send_seq=535 receive_seq=535 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999870 adj=49997624 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=25831 bytes_read=695606 bytes_retransmit=9 bytes_invalid=0 send_seq=3277 receive_seq=3277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997677 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12474 bytes_read=64470 bytes_retransmit=9 bytes_invalid=0 send_seq=1278 receive_seq=1278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997527 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3541 bytes_read=109671 bytes_retransmit=9 bytes_invalid=0 send_seq=541 receive_seq=541 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999513 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4135 bytes_read=12234 bytes_retransmit=9 bytes_invalid=0 send_seq=536 receive_seq=536 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47211 bytes_read=367900 bytes_retransmit=0 bytes_invalid=0 send_seq=4173 receive_seq=4173 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998652 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=44.2 th1: temp=43.3 th2: temp=44.1 th3: temp=42.4 sysload=0.21 cputime=60.916 memavail=7409040 print_time=474.050 buffer_time=2.398 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 450.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5271491 bytes_read=670206 bytes_retransmit=9 bytes_invalid=0 send_seq=94026 receive_seq=94026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=19986 freq=400015566 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3388 bytes_read=12475 bytes_retransmit=0 bytes_invalid=0 send_seq=536 receive_seq=536 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999864 adj=49997635 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=25907 bytes_read=698693 bytes_retransmit=9 bytes_invalid=0 send_seq=3288 receive_seq=3288 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997676 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12480 bytes_read=64593 bytes_retransmit=9 bytes_invalid=0 send_seq=1279 receive_seq=1279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997527 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3547 bytes_read=109965 bytes_retransmit=9 bytes_invalid=0 send_seq=542 receive_seq=542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999513 adj=47997629 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4141 bytes_read=12250 bytes_retransmit=9 bytes_invalid=0 send_seq=537 receive_seq=537 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47217 bytes_read=368256 bytes_retransmit=0 bytes_invalid=0 send_seq=4174 receive_seq=4174 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998649 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.3 th1: temp=43.3 th2: temp=44.2 th3: temp=42.3 sysload=0.21 cputime=61.050 memavail=7409040 print_time=475.126 buffer_time=2.474 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 451.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5284058 bytes_read=671595 bytes_retransmit=9 bytes_invalid=0 send_seq=94239 receive_seq=94239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=14790 freq=400015576 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3394 bytes_read=12491 bytes_retransmit=0 bytes_invalid=0 send_seq=537 receive_seq=537 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999870 adj=49997648 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=25983 bytes_read=701749 bytes_retransmit=9 bytes_invalid=0 send_seq=3299 receive_seq=3299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997693 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12486 bytes_read=64693 bytes_retransmit=9 bytes_invalid=0 send_seq=1280 receive_seq=1280 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3553 bytes_read=110199 bytes_retransmit=9 bytes_invalid=0 send_seq=543 receive_seq=543 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999512 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4147 bytes_read=12266 bytes_retransmit=9 bytes_invalid=0 send_seq=538 receive_seq=538 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47223 bytes_read=368612 bytes_retransmit=0 bytes_invalid=0 send_seq=4175 receive_seq=4175 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998662 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=44.8 th1: temp=42.8 th2: temp=43.7 th3: temp=42.5 sysload=0.20 cputime=61.165 memavail=7409040 print_time=475.664 buffer_time=2.011 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 452.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5296574 bytes_read=672965 bytes_retransmit=9 bytes_invalid=0 send_seq=94448 receive_seq=94448 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=15718 freq=400015588 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3400 bytes_read=12507 bytes_retransmit=0 bytes_invalid=0 send_seq=538 receive_seq=538 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999864 adj=49997711 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=26059 bytes_read=704807 bytes_retransmit=9 bytes_invalid=0 send_seq=3310 receive_seq=3310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997643 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12492 bytes_read=64793 bytes_retransmit=9 bytes_invalid=0 send_seq=1281 receive_seq=1281 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3559 bytes_read=110433 bytes_retransmit=9 bytes_invalid=0 send_seq=544 receive_seq=544 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999512 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4153 bytes_read=12293 bytes_retransmit=9 bytes_invalid=0 send_seq=539 receive_seq=539 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47229 bytes_read=368968 bytes_retransmit=0 bytes_invalid=0 send_seq=4176 receive_seq=4176 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999892 adj=31998644 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=44.4 th1: temp=43.4 th2: temp=44.1 th3: temp=42.5 sysload=0.20 cputime=61.295 memavail=7409040 print_time=476.741 buffer_time=2.087 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 453.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5309604 bytes_read=674370 bytes_retransmit=9 bytes_invalid=0 send_seq=94667 receive_seq=94667 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=26 upcoming_bytes=16198 freq=400015576 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3406 bytes_read=12523 bytes_retransmit=0 bytes_invalid=0 send_seq=539 receive_seq=539 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999858 adj=49997638 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=26135 bytes_read=707893 bytes_retransmit=9 bytes_invalid=0 send_seq=3321 receive_seq=3321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997635 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12498 bytes_read=64935 bytes_retransmit=9 bytes_invalid=0 send_seq=1282 receive_seq=1282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997471 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3565 bytes_read=110742 bytes_retransmit=9 bytes_invalid=0 send_seq=545 receive_seq=545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997600 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4159 bytes_read=12309 bytes_retransmit=9 bytes_invalid=0 send_seq=540 receive_seq=540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47235 bytes_read=369324 bytes_retransmit=0 bytes_invalid=0 send_seq=4177 receive_seq=4177 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999892 adj=31998625 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=44.3 th1: temp=43.2 th2: temp=43.9 th3: temp=42.4 sysload=0.20 cputime=61.427 memavail=7409040 print_time=477.817 buffer_time=2.163 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 454.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5322123 bytes_read=675749 bytes_retransmit=9 bytes_invalid=0 send_seq=94878 receive_seq=94878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=17126 freq=400015566 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3412 bytes_read=12552 bytes_retransmit=0 bytes_invalid=0 send_seq=540 receive_seq=540 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999853 adj=49997649 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=26211 bytes_read=710949 bytes_retransmit=9 bytes_invalid=0 send_seq=3332 receive_seq=3332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997644 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12504 bytes_read=65035 bytes_retransmit=9 bytes_invalid=0 send_seq=1283 receive_seq=1283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000002 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3571 bytes_read=110976 bytes_retransmit=9 bytes_invalid=0 send_seq=546 receive_seq=546 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4165 bytes_read=12325 bytes_retransmit=9 bytes_invalid=0 send_seq=541 receive_seq=541 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47241 bytes_read=369680 bytes_retransmit=0 bytes_invalid=0 send_seq=4178 receive_seq=4178 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999892 adj=31998641 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=44.3 th1: temp=43.3 th2: temp=44.3 th3: temp=42.6 sysload=0.20 cputime=61.559 memavail=7409040 print_time=478.894 buffer_time=2.238 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 455.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5334659 bytes_read=677155 bytes_retransmit=9 bytes_invalid=0 send_seq=95091 receive_seq=95091 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=18054 freq=400015558 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3418 bytes_read=12568 bytes_retransmit=0 bytes_invalid=0 send_seq=541 receive_seq=541 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999848 adj=49997661 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=26287 bytes_read=714080 bytes_retransmit=9 bytes_invalid=0 send_seq=3343 receive_seq=3343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997643 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12510 bytes_read=65135 bytes_retransmit=9 bytes_invalid=0 send_seq=1284 receive_seq=1284 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000013 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3577 bytes_read=111210 bytes_retransmit=9 bytes_invalid=0 send_seq=547 receive_seq=547 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999510 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4171 bytes_read=12341 bytes_retransmit=9 bytes_invalid=0 send_seq=542 receive_seq=542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999905 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47247 bytes_read=370036 bytes_retransmit=0 bytes_invalid=0 send_seq=4179 receive_seq=4179 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999891 adj=31998649 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=44.0 th1: temp=43.3 th2: temp=43.9 th3: temp=42.4 sysload=0.20 cputime=61.693 memavail=7408812 print_time=479.970 buffer_time=2.313 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 456.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5347191 bytes_read=678520 bytes_retransmit=9 bytes_invalid=0 send_seq=95302 receive_seq=95302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=18959 freq=400015567 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3424 bytes_read=12584 bytes_retransmit=0 bytes_invalid=0 send_seq=542 receive_seq=542 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999843 adj=49997672 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=26363 bytes_read=717165 bytes_retransmit=9 bytes_invalid=0 send_seq=3354 receive_seq=3354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997682 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12516 bytes_read=65263 bytes_retransmit=9 bytes_invalid=0 send_seq=1285 receive_seq=1285 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000013 adj=63997646 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3583 bytes_read=111504 bytes_retransmit=9 bytes_invalid=0 send_seq=548 receive_seq=548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999510 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4177 bytes_read=12357 bytes_retransmit=9 bytes_invalid=0 send_seq=543 receive_seq=543 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47253 bytes_read=370392 bytes_retransmit=0 bytes_invalid=0 send_seq=4180 receive_seq=4180 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999891 adj=31998647 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=44.3 th1: temp=43.2 th2: temp=44.1 th3: temp=42.3 sysload=0.18 cputime=61.830 memavail=7408848 print_time=481.047 buffer_time=2.389 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 457.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5359768 bytes_read=679924 bytes_retransmit=9 bytes_invalid=0 send_seq=95515 receive_seq=95515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=26 upcoming_bytes=19870 freq=400015554 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3430 bytes_read=12600 bytes_retransmit=0 bytes_invalid=0 send_seq=543 receive_seq=543 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999839 adj=49997656 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=26432 bytes_read=720200 bytes_retransmit=9 bytes_invalid=0 send_seq=3364 receive_seq=3364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997655 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12522 bytes_read=65363 bytes_retransmit=9 bytes_invalid=0 send_seq=1286 receive_seq=1286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000011 adj=63997598 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3589 bytes_read=111738 bytes_retransmit=9 bytes_invalid=0 send_seq=549 receive_seq=549 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999510 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4183 bytes_read=12384 bytes_retransmit=9 bytes_invalid=0 send_seq=544 receive_seq=544 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999906 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47259 bytes_read=370748 bytes_retransmit=0 bytes_invalid=0 send_seq=4181 receive_seq=4181 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999890 adj=31998638 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=44.4 th1: temp=43.2 th2: temp=44.1 th3: temp=42.5 sysload=0.18 cputime=61.959 memavail=7408848 print_time=482.123 buffer_time=2.464 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 458.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5372250 bytes_read=681269 bytes_retransmit=9 bytes_invalid=0 send_seq=95722 receive_seq=95722 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=14707 freq=400015543 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3436 bytes_read=12616 bytes_retransmit=0 bytes_invalid=0 send_seq=544 receive_seq=544 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999833 adj=49997671 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=26508 bytes_read=723256 bytes_retransmit=9 bytes_invalid=0 send_seq=3375 receive_seq=3375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997667 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12528 bytes_read=65477 bytes_retransmit=9 bytes_invalid=0 send_seq=1287 receive_seq=1287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000010 adj=63997589 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3595 bytes_read=112002 bytes_retransmit=9 bytes_invalid=0 send_seq=550 receive_seq=550 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999510 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4189 bytes_read=12400 bytes_retransmit=9 bytes_invalid=0 send_seq=545 receive_seq=545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.6 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47265 bytes_read=371104 bytes_retransmit=0 bytes_invalid=0 send_seq=4182 receive_seq=4182 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998642 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=44.7 th1: temp=43.4 th2: temp=44.3 th3: temp=42.5 sysload=0.18 cputime=62.083 memavail=7403068 print_time=482.661 buffer_time=2.002 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 459.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5384733 bytes_read=682624 bytes_retransmit=9 bytes_invalid=0 send_seq=95931 receive_seq=95931 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=15651 freq=400015540 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3442 bytes_read=12645 bytes_retransmit=0 bytes_invalid=0 send_seq=545 receive_seq=545 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999828 adj=49997618 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=26584 bytes_read=726341 bytes_retransmit=9 bytes_invalid=0 send_seq=3386 receive_seq=3386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997657 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12534 bytes_read=65605 bytes_retransmit=9 bytes_invalid=0 send_seq=1288 receive_seq=1288 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000008 adj=63997591 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3601 bytes_read=112281 bytes_retransmit=9 bytes_invalid=0 send_seq=551 receive_seq=551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999510 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4195 bytes_read=12416 bytes_retransmit=9 bytes_invalid=0 send_seq=546 receive_seq=546 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999462 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47271 bytes_read=371460 bytes_retransmit=0 bytes_invalid=0 send_seq=4183 receive_seq=4183 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999892 adj=31998687 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=44.5 th1: temp=43.6 th2: temp=44.1 th3: temp=42.5 sysload=0.18 cputime=62.225 memavail=7409000 print_time=483.738 buffer_time=2.079 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 460.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5397811 bytes_read=684089 bytes_retransmit=9 bytes_invalid=0 send_seq=96153 receive_seq=96153 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=16099 freq=400015522 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3448 bytes_read=12661 bytes_retransmit=0 bytes_invalid=0 send_seq=546 receive_seq=546 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999826 adj=49997598 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=26660 bytes_read=729414 bytes_retransmit=9 bytes_invalid=0 send_seq=3397 receive_seq=3397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997640 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12540 bytes_read=65705 bytes_retransmit=9 bytes_invalid=0 send_seq=1289 receive_seq=1289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997570 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3607 bytes_read=112515 bytes_retransmit=9 bytes_invalid=0 send_seq=552 receive_seq=552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999510 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4201 bytes_read=12432 bytes_retransmit=9 bytes_invalid=0 send_seq=547 receive_seq=547 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47277 bytes_read=371816 bytes_retransmit=0 bytes_invalid=0 send_seq=4184 receive_seq=4184 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999892 adj=31998673 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=44.6 th1: temp=43.4 th2: temp=44.3 th3: temp=42.7 sysload=0.18 cputime=62.357 memavail=7409000 print_time=484.814 buffer_time=2.155 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 461.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5410327 bytes_read=685440 bytes_retransmit=9 bytes_invalid=0 send_seq=96362 receive_seq=96362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=17027 freq=400015527 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3454 bytes_read=12677 bytes_retransmit=0 bytes_invalid=0 send_seq=547 receive_seq=547 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999821 adj=49997669 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=26736 bytes_read=732473 bytes_retransmit=9 bytes_invalid=0 send_seq=3408 receive_seq=3408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997673 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12546 bytes_read=65805 bytes_retransmit=9 bytes_invalid=0 send_seq=1290 receive_seq=1290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997582 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3613 bytes_read=112764 bytes_retransmit=9 bytes_invalid=0 send_seq=553 receive_seq=553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4207 bytes_read=12448 bytes_retransmit=9 bytes_invalid=0 send_seq=548 receive_seq=548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47283 bytes_read=372172 bytes_retransmit=0 bytes_invalid=0 send_seq=4185 receive_seq=4185 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999892 adj=31998681 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=44.3 th1: temp=43.5 th2: temp=44.4 th3: temp=42.5 sysload=0.17 cputime=62.490 memavail=7409004 print_time=485.891 buffer_time=2.230 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 462.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5422830 bytes_read=686815 bytes_retransmit=9 bytes_invalid=0 send_seq=96575 receive_seq=96575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=17971 freq=400015533 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3460 bytes_read=12693 bytes_retransmit=0 bytes_invalid=0 send_seq=548 receive_seq=548 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999815 adj=49997643 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=26812 bytes_read=735559 bytes_retransmit=9 bytes_invalid=0 send_seq=3419 receive_seq=3419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000181 adj=63997645 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12552 bytes_read=65933 bytes_retransmit=9 bytes_invalid=0 send_seq=1291 receive_seq=1291 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997546 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3619 bytes_read=113043 bytes_retransmit=9 bytes_invalid=0 send_seq=554 receive_seq=554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999512 adj=47997689 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4213 bytes_read=12475 bytes_retransmit=9 bytes_invalid=0 send_seq=549 receive_seq=549 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47289 bytes_read=372528 bytes_retransmit=0 bytes_invalid=0 send_seq=4186 receive_seq=4186 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999891 adj=31998669 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=44.4 th1: temp=43.6 th2: temp=44.5 th3: temp=42.4 sysload=0.17 cputime=62.623 memavail=7409004 print_time=486.967 buffer_time=2.306 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 463.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5435417 bytes_read=688214 bytes_retransmit=9 bytes_invalid=0 send_seq=96787 receive_seq=96787 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=18876 freq=400015551 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3466 bytes_read=12709 bytes_retransmit=0 bytes_invalid=0 send_seq=549 receive_seq=549 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999810 adj=49997623 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=26888 bytes_read=738673 bytes_retransmit=9 bytes_invalid=0 send_seq=3430 receive_seq=3430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997623 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12558 bytes_read=66033 bytes_retransmit=9 bytes_invalid=0 send_seq=1292 receive_seq=1292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3625 bytes_read=113292 bytes_retransmit=9 bytes_invalid=0 send_seq=555 receive_seq=555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999512 adj=47997677 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4219 bytes_read=12491 bytes_retransmit=9 bytes_invalid=0 send_seq=550 receive_seq=550 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999457 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47295 bytes_read=372884 bytes_retransmit=0 bytes_invalid=0 send_seq=4187 receive_seq=4187 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998653 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=44.4 th1: temp=43.2 th2: temp=44.4 th3: temp=42.5 sysload=0.17 cputime=62.760 memavail=7409004 print_time=488.044 buffer_time=2.383 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 464.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5447927 bytes_read=689579 bytes_retransmit=9 bytes_invalid=0 send_seq=96998 receive_seq=96998 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=19804 freq=400015547 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3472 bytes_read=12738 bytes_retransmit=0 bytes_invalid=0 send_seq=550 receive_seq=550 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999803 adj=49997593 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=26964 bytes_read=741730 bytes_retransmit=9 bytes_invalid=0 send_seq=3441 receive_seq=3441 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997595 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12564 bytes_read=66147 bytes_retransmit=9 bytes_invalid=0 send_seq=1293 receive_seq=1293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997482 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3631 bytes_read=113541 bytes_retransmit=9 bytes_invalid=0 send_seq=556 receive_seq=556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4225 bytes_read=12507 bytes_retransmit=9 bytes_invalid=0 send_seq=551 receive_seq=551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47301 bytes_read=373240 bytes_retransmit=0 bytes_invalid=0 send_seq=4188 receive_seq=4188 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998668 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=44.4 th1: temp=43.4 th2: temp=44.2 th3: temp=42.4 sysload=0.17 cputime=62.896 memavail=7409004 print_time=489.120 buffer_time=2.458 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 465.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5460599 bytes_read=690990 bytes_retransmit=9 bytes_invalid=0 send_seq=97215 receive_seq=97215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=20633 freq=400015539 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3478 bytes_read=12754 bytes_retransmit=0 bytes_invalid=0 send_seq=551 receive_seq=551 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999798 adj=49997582 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=27040 bytes_read=744832 bytes_retransmit=9 bytes_invalid=0 send_seq=3452 receive_seq=3452 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000177 adj=63997602 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12570 bytes_read=66275 bytes_retransmit=9 bytes_invalid=0 send_seq=1294 receive_seq=1294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000002 adj=63997482 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3637 bytes_read=113820 bytes_retransmit=9 bytes_invalid=0 send_seq=557 receive_seq=557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4231 bytes_read=12523 bytes_retransmit=9 bytes_invalid=0 send_seq=552 receive_seq=552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47307 bytes_read=373596 bytes_retransmit=0 bytes_invalid=0 send_seq=4189 receive_seq=4189 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998664 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=44.2 th1: temp=43.4 th2: temp=44.4 th3: temp=42.7 sysload=0.17 cputime=63.026 memavail=7410496 print_time=490.197 buffer_time=2.526 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 466.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5473130 bytes_read=692389 bytes_retransmit=9 bytes_invalid=0 send_seq=97427 receive_seq=97427 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=15453 freq=400015523 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3484 bytes_read=12770 bytes_retransmit=0 bytes_invalid=0 send_seq=552 receive_seq=552 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999793 adj=49997595 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=27116 bytes_read=747890 bytes_retransmit=9 bytes_invalid=0 send_seq=3463 receive_seq=3463 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997616 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12576 bytes_read=66375 bytes_retransmit=9 bytes_invalid=0 send_seq=1295 receive_seq=1295 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000001 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3643 bytes_read=114054 bytes_retransmit=9 bytes_invalid=0 send_seq=558 receive_seq=558 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4237 bytes_read=12539 bytes_retransmit=9 bytes_invalid=0 send_seq=553 receive_seq=553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47313 bytes_read=373952 bytes_retransmit=0 bytes_invalid=0 send_seq=4190 receive_seq=4190 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998674 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.7 th1: temp=43.4 th2: temp=44.3 th3: temp=42.6 sysload=0.15 cputime=63.149 memavail=7410496 print_time=490.735 buffer_time=2.064 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 467.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5486035 bytes_read=693794 bytes_retransmit=9 bytes_invalid=0 send_seq=97646 receive_seq=97646 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=16049 freq=400015528 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3490 bytes_read=12786 bytes_retransmit=0 bytes_invalid=0 send_seq=553 receive_seq=553 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999789 adj=49997560 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=27192 bytes_read=750946 bytes_retransmit=9 bytes_invalid=0 send_seq=3474 receive_seq=3474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997626 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12582 bytes_read=66475 bytes_retransmit=9 bytes_invalid=0 send_seq=1296 receive_seq=1296 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997512 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3649 bytes_read=114318 bytes_retransmit=9 bytes_invalid=0 send_seq=559 receive_seq=559 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999513 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4243 bytes_read=12566 bytes_retransmit=9 bytes_invalid=0 send_seq=554 receive_seq=554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47319 bytes_read=374308 bytes_retransmit=0 bytes_invalid=0 send_seq=4191 receive_seq=4191 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998688 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=44.8 th1: temp=43.4 th2: temp=44.4 th3: temp=42.7 sysload=0.15 cputime=63.279 memavail=7410496 print_time=491.811 buffer_time=2.140 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 468.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5498676 bytes_read=695174 bytes_retransmit=9 bytes_invalid=0 send_seq=97860 receive_seq=97860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=16861 freq=400015525 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3496 bytes_read=12802 bytes_retransmit=0 bytes_invalid=0 send_seq=554 receive_seq=554 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999784 adj=49997532 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=27268 bytes_read=754088 bytes_retransmit=9 bytes_invalid=0 send_seq=3485 receive_seq=3485 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997624 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12588 bytes_read=66603 bytes_retransmit=9 bytes_invalid=0 send_seq=1297 receive_seq=1297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997522 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3655 bytes_read=114597 bytes_retransmit=9 bytes_invalid=0 send_seq=560 receive_seq=560 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999512 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4249 bytes_read=12582 bytes_retransmit=9 bytes_invalid=0 send_seq=555 receive_seq=555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47325 bytes_read=374664 bytes_retransmit=0 bytes_invalid=0 send_seq=4192 receive_seq=4192 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998673 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=44.6 th1: temp=43.9 th2: temp=44.4 th3: temp=42.6 sysload=0.15 cputime=63.414 memavail=7410496 print_time=492.888 buffer_time=2.217 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 469.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5511232 bytes_read=696573 bytes_retransmit=9 bytes_invalid=0 send_seq=98072 receive_seq=98072 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=17773 freq=400015526 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3502 bytes_read=12818 bytes_retransmit=0 bytes_invalid=0 send_seq=555 receive_seq=555 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999778 adj=49997551 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=27337 bytes_read=757125 bytes_retransmit=9 bytes_invalid=0 send_seq=3495 receive_seq=3495 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000174 adj=63997643 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12594 bytes_read=66717 bytes_retransmit=9 bytes_invalid=0 send_seq=1298 receive_seq=1298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3661 bytes_read=114831 bytes_retransmit=9 bytes_invalid=0 send_seq=561 receive_seq=561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999512 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4255 bytes_read=12598 bytes_retransmit=9 bytes_invalid=0 send_seq=556 receive_seq=556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47331 bytes_read=375020 bytes_retransmit=0 bytes_invalid=0 send_seq=4193 receive_seq=4193 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999895 adj=31998666 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=44.4 th1: temp=43.5 th2: temp=44.5 th3: temp=42.5 sysload=0.15 cputime=63.547 memavail=7410244 print_time=493.964 buffer_time=2.292 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 470.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5523758 bytes_read=697964 bytes_retransmit=9 bytes_invalid=0 send_seq=98285 receive_seq=98285 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=18694 freq=400015508 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3508 bytes_read=12847 bytes_retransmit=0 bytes_invalid=0 send_seq=556 receive_seq=556 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999773 adj=49997550 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=27413 bytes_read=760199 bytes_retransmit=9 bytes_invalid=0 send_seq=3506 receive_seq=3506 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000174 adj=63997645 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12600 bytes_read=66817 bytes_retransmit=9 bytes_invalid=0 send_seq=1299 receive_seq=1299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997537 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3667 bytes_read=115095 bytes_retransmit=9 bytes_invalid=0 send_seq=562 receive_seq=562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999512 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4261 bytes_read=12614 bytes_retransmit=9 bytes_invalid=0 send_seq=557 receive_seq=557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47337 bytes_read=375376 bytes_retransmit=0 bytes_invalid=0 send_seq=4194 receive_seq=4194 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998679 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.5 th1: temp=43.6 th2: temp=44.3 th3: temp=42.7 sysload=0.15 cputime=63.677 memavail=7410040 print_time=495.041 buffer_time=2.368 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 471.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5536239 bytes_read=699324 bytes_retransmit=9 bytes_invalid=0 send_seq=98495 receive_seq=98495 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=19638 freq=400015507 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3514 bytes_read=12863 bytes_retransmit=0 bytes_invalid=0 send_seq=557 receive_seq=557 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999768 adj=49997570 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=27489 bytes_read=763285 bytes_retransmit=9 bytes_invalid=0 send_seq=3517 receive_seq=3517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000173 adj=63997684 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12606 bytes_read=66945 bytes_retransmit=9 bytes_invalid=0 send_seq=1300 receive_seq=1300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997573 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3673 bytes_read=115359 bytes_retransmit=9 bytes_invalid=0 send_seq=563 receive_seq=563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4267 bytes_read=12630 bytes_retransmit=9 bytes_invalid=0 send_seq=558 receive_seq=558 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47343 bytes_read=375732 bytes_retransmit=0 bytes_invalid=0 send_seq=4195 receive_seq=4195 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998686 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.4 th1: temp=43.6 th2: temp=44.4 th3: temp=42.6 sysload=0.14 cputime=63.809 memavail=7410040 print_time=496.117 buffer_time=2.444 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 472.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5548837 bytes_read=700728 bytes_retransmit=9 bytes_invalid=0 send_seq=98709 receive_seq=98709 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=20550 freq=400015508 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3520 bytes_read=12879 bytes_retransmit=0 bytes_invalid=0 send_seq=558 receive_seq=558 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999763 adj=49997574 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=27565 bytes_read=766342 bytes_retransmit=9 bytes_invalid=0 send_seq=3528 receive_seq=3528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000172 adj=63997671 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12612 bytes_read=67045 bytes_retransmit=9 bytes_invalid=0 send_seq=1301 receive_seq=1301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3679 bytes_read=115593 bytes_retransmit=9 bytes_invalid=0 send_seq=564 receive_seq=564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4273 bytes_read=12657 bytes_retransmit=9 bytes_invalid=0 send_seq=559 receive_seq=559 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47349 bytes_read=376088 bytes_retransmit=0 bytes_invalid=0 send_seq=4196 receive_seq=4196 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998673 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.9 th1: temp=43.5 th2: temp=44.2 th3: temp=42.6 sysload=0.14 cputime=63.937 memavail=7410040 print_time=497.194 buffer_time=2.520 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 473.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5561353 bytes_read=702083 bytes_retransmit=9 bytes_invalid=0 send_seq=98918 receive_seq=98918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=15370 freq=400015513 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3526 bytes_read=12895 bytes_retransmit=0 bytes_invalid=0 send_seq=559 receive_seq=559 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999759 adj=49997577 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=27641 bytes_read=769399 bytes_retransmit=9 bytes_invalid=0 send_seq=3539 receive_seq=3539 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000172 adj=63997671 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12618 bytes_read=67145 bytes_retransmit=9 bytes_invalid=0 send_seq=1302 receive_seq=1302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000002 adj=63997533 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3685 bytes_read=115872 bytes_retransmit=9 bytes_invalid=0 send_seq=565 receive_seq=565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997669 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4279 bytes_read=12673 bytes_retransmit=9 bytes_invalid=0 send_seq=560 receive_seq=560 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47355 bytes_read=376444 bytes_retransmit=0 bytes_invalid=0 send_seq=4197 receive_seq=4197 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998659 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.6 th1: temp=43.3 th2: temp=44.0 th3: temp=42.6 sysload=0.14 cputime=64.055 memavail=7409788 print_time=497.732 buffer_time=2.058 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 474.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5574131 bytes_read=703468 bytes_retransmit=9 bytes_invalid=0 send_seq=99133 receive_seq=99133 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=16049 freq=400015570 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3532 bytes_read=12911 bytes_retransmit=0 bytes_invalid=0 send_seq=560 receive_seq=560 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999755 adj=49997517 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=27717 bytes_read=772484 bytes_retransmit=9 bytes_invalid=0 send_seq=3550 receive_seq=3550 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000171 adj=63997654 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12624 bytes_read=67287 bytes_retransmit=9 bytes_invalid=0 send_seq=1303 receive_seq=1303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000001 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3691 bytes_read=116136 bytes_retransmit=9 bytes_invalid=0 send_seq=566 receive_seq=566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4285 bytes_read=12689 bytes_retransmit=9 bytes_invalid=0 send_seq=561 receive_seq=561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47361 bytes_read=376800 bytes_retransmit=0 bytes_invalid=0 send_seq=4198 receive_seq=4198 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999895 adj=31998659 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.2 th1: temp=43.6 th2: temp=44.5 th3: temp=42.6 sysload=0.14 cputime=64.187 memavail=7409816 print_time=498.808 buffer_time=2.134 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 475.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5586849 bytes_read=704888 bytes_retransmit=9 bytes_invalid=0 send_seq=99346 receive_seq=99346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=16795 freq=400015568 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=3538 bytes_read=12940 bytes_retransmit=0 bytes_invalid=0 send_seq=561 receive_seq=561 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999751 adj=49997422 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=27793 bytes_read=775615 bytes_retransmit=9 bytes_invalid=0 send_seq=3561 receive_seq=3561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000173 adj=63997545 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12630 bytes_read=67387 bytes_retransmit=9 bytes_invalid=0 send_seq=1304 receive_seq=1304 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000001 adj=63997391 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3697 bytes_read=116370 bytes_retransmit=9 bytes_invalid=0 send_seq=567 receive_seq=567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997572 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4291 bytes_read=12705 bytes_retransmit=9 bytes_invalid=0 send_seq=562 receive_seq=562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999425 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47367 bytes_read=377156 bytes_retransmit=0 bytes_invalid=0 send_seq=4199 receive_seq=4199 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998618 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=44.7 th1: temp=43.6 th2: temp=44.5 th3: temp=42.7 sysload=0.14 cputime=64.327 memavail=7402792 print_time=499.885 buffer_time=2.210 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 476.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5599373 bytes_read=706258 bytes_retransmit=9 bytes_invalid=0 send_seq=99558 receive_seq=99558 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=17706 freq=400015573 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=3544 bytes_read=12956 bytes_retransmit=0 bytes_invalid=0 send_seq=562 receive_seq=562 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999748 adj=49997458 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=27869 bytes_read=778673 bytes_retransmit=9 bytes_invalid=0 send_seq=3572 receive_seq=3572 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000172 adj=63997592 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12636 bytes_read=67487 bytes_retransmit=9 bytes_invalid=0 send_seq=1305 receive_seq=1305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000000 adj=63997422 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3703 bytes_read=116634 bytes_retransmit=9 bytes_invalid=0 send_seq=568 receive_seq=568 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999512 adj=47997588 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4297 bytes_read=12721 bytes_retransmit=9 bytes_invalid=0 send_seq=563 receive_seq=563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47373 bytes_read=377512 bytes_retransmit=0 bytes_invalid=0 send_seq=4200 receive_seq=4200 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998619 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=44.9 th1: temp=43.7 th2: temp=44.6 th3: temp=42.6 sysload=0.21 cputime=64.461 memavail=7409172 print_time=500.961 buffer_time=2.286 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 477.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5611968 bytes_read=707628 bytes_retransmit=9 bytes_invalid=0 send_seq=99770 receive_seq=99770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=18627 freq=400015562 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=3550 bytes_read=12972 bytes_retransmit=0 bytes_invalid=0 send_seq=563 receive_seq=563 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999744 adj=49997491 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=27945 bytes_read=781757 bytes_retransmit=9 bytes_invalid=0 send_seq=3583 receive_seq=3583 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000173 adj=63997602 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12642 bytes_read=67615 bytes_retransmit=9 bytes_invalid=0 send_seq=1306 receive_seq=1306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000001 adj=63997426 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3709 bytes_read=116898 bytes_retransmit=9 bytes_invalid=0 send_seq=569 receive_seq=569 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997613 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4303 bytes_read=12748 bytes_retransmit=9 bytes_invalid=0 send_seq=564 receive_seq=564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47379 bytes_read=377868 bytes_retransmit=0 bytes_invalid=0 send_seq=4201 receive_seq=4201 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999892 adj=31998611 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.011 th0: temp=44.8 th1: temp=43.5 th2: temp=44.5 th3: temp=42.8 sysload=0.21 cputime=64.595 memavail=7409172 print_time=502.038 buffer_time=2.362 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 478.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5624499 bytes_read=709027 bytes_retransmit=9 bytes_invalid=0 send_seq=99982 receive_seq=99982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=19555 freq=400015561 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=3556 bytes_read=12988 bytes_retransmit=0 bytes_invalid=0 send_seq=564 receive_seq=564 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999740 adj=49997529 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=28021 bytes_read=784814 bytes_retransmit=9 bytes_invalid=0 send_seq=3594 receive_seq=3594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000172 adj=63997648 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12648 bytes_read=67715 bytes_retransmit=9 bytes_invalid=0 send_seq=1307 receive_seq=1307 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000008 adj=63997468 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3715 bytes_read=117147 bytes_retransmit=9 bytes_invalid=0 send_seq=570 receive_seq=570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4309 bytes_read=12764 bytes_retransmit=9 bytes_invalid=0 send_seq=565 receive_seq=565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47385 bytes_read=378224 bytes_retransmit=0 bytes_invalid=0 send_seq=4202 receive_seq=4202 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999892 adj=31998620 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=44.5 th1: temp=43.4 th2: temp=44.5 th3: temp=42.9 sysload=0.21 cputime=64.725 memavail=7409172 print_time=503.114 buffer_time=2.438 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 479.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5636966 bytes_read=710392 bytes_retransmit=9 bytes_invalid=0 send_seq=100193 receive_seq=100193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=20500 freq=400015560 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=3562 bytes_read=13004 bytes_retransmit=0 bytes_invalid=0 send_seq=565 receive_seq=565 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999736 adj=49997542 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=28097 bytes_read=787873 bytes_retransmit=9 bytes_invalid=0 send_seq=3605 receive_seq=3605 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000172 adj=63997646 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12654 bytes_read=67829 bytes_retransmit=9 bytes_invalid=0 send_seq=1308 receive_seq=1308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997558 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3721 bytes_read=117411 bytes_retransmit=9 bytes_invalid=0 send_seq=571 receive_seq=571 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4315 bytes_read=12780 bytes_retransmit=9 bytes_invalid=0 send_seq=566 receive_seq=566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999436 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47391 bytes_read=378564 bytes_retransmit=0 bytes_invalid=0 send_seq=4203 receive_seq=4203 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999892 adj=31998624 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=45.0 th1: temp=44.0 th2: temp=44.4 th3: temp=42.8 sysload=0.21 cputime=64.850 memavail=7409172 print_time=504.191 buffer_time=2.514 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 480.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5649555 bytes_read=711794 bytes_retransmit=9 bytes_invalid=0 send_seq=100406 receive_seq=100406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=15303 freq=400015574 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3574 bytes_read=13049 bytes_retransmit=0 bytes_invalid=0 send_seq=567 receive_seq=567 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999730 adj=49997549 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=28179 bytes_read=790990 bytes_retransmit=9 bytes_invalid=0 send_seq=3617 receive_seq=3617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000172 adj=63997647 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12666 bytes_read=67973 bytes_retransmit=9 bytes_invalid=0 send_seq=1310 receive_seq=1310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000008 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3733 bytes_read=117691 bytes_retransmit=9 bytes_invalid=0 send_seq=573 receive_seq=573 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997689 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4327 bytes_read=12812 bytes_retransmit=9 bytes_invalid=0 send_seq=568 receive_seq=568 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47403 bytes_read=378936 bytes_retransmit=0 bytes_invalid=0 send_seq=4205 receive_seq=4205 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999891 adj=31998626 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=44.3 th1: temp=43.7 th2: temp=44.5 th3: temp=42.8 sysload=0.21 cputime=64.973 memavail=7409172 print_time=504.729 buffer_time=2.052 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 481.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5662285 bytes_read=713203 bytes_retransmit=9 bytes_invalid=0 send_seq=100620 receive_seq=100620 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=16049 freq=400015789 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3580 bytes_read=13065 bytes_retransmit=0 bytes_invalid=0 send_seq=568 receive_seq=568 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999725 adj=49997464 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=28248 bytes_read=794025 bytes_retransmit=9 bytes_invalid=0 send_seq=3627 receive_seq=3627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000179 adj=63997630 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12672 bytes_read=68073 bytes_retransmit=9 bytes_invalid=0 send_seq=1311 receive_seq=1311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000008 adj=63997527 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3739 bytes_read=117925 bytes_retransmit=9 bytes_invalid=0 send_seq=574 receive_seq=574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4333 bytes_read=12828 bytes_retransmit=9 bytes_invalid=0 send_seq=569 receive_seq=569 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47409 bytes_read=379292 bytes_retransmit=0 bytes_invalid=0 send_seq=4206 receive_seq=4206 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999891 adj=31998603 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=44.5 th1: temp=43.7 th2: temp=44.5 th3: temp=42.9 sysload=0.19 cputime=65.104 memavail=7409172 print_time=505.805 buffer_time=2.128 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 482.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5675043 bytes_read=714588 bytes_retransmit=9 bytes_invalid=0 send_seq=100836 receive_seq=100836 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=16712 freq=400015773 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3586 bytes_read=13081 bytes_retransmit=0 bytes_invalid=0 send_seq=569 receive_seq=569 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999721 adj=49997112 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=28324 bytes_read=797084 bytes_retransmit=9 bytes_invalid=0 send_seq=3638 receive_seq=3638 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997293 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12678 bytes_read=68173 bytes_retransmit=9 bytes_invalid=0 send_seq=1312 receive_seq=1312 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997100 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3745 bytes_read=118189 bytes_retransmit=9 bytes_invalid=0 send_seq=575 receive_seq=575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997332 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4339 bytes_read=12855 bytes_retransmit=9 bytes_invalid=0 send_seq=570 receive_seq=570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999366 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47415 bytes_read=379648 bytes_retransmit=0 bytes_invalid=0 send_seq=4207 receive_seq=4207 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999891 adj=31998406 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.011 th0: temp=44.7 th1: temp=44.0 th2: temp=44.5 th3: temp=42.8 sysload=0.19 cputime=65.235 memavail=7409192 print_time=506.882 buffer_time=2.204 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 483.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5687637 bytes_read=715956 bytes_retransmit=9 bytes_invalid=0 send_seq=101049 receive_seq=101048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=17623 freq=400015751 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3592 bytes_read=13097 bytes_retransmit=0 bytes_invalid=0 send_seq=570 receive_seq=570 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999716 adj=49997240 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=28400 bytes_read=800226 bytes_retransmit=9 bytes_invalid=0 send_seq=3649 receive_seq=3649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000177 adj=63997403 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12684 bytes_read=68301 bytes_retransmit=9 bytes_invalid=0 send_seq=1313 receive_seq=1313 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997209 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3751 bytes_read=118468 bytes_retransmit=9 bytes_invalid=0 send_seq=576 receive_seq=576 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997415 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4345 bytes_read=12871 bytes_retransmit=9 bytes_invalid=0 send_seq=571 receive_seq=571 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999390 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47421 bytes_read=380004 bytes_retransmit=0 bytes_invalid=0 send_seq=4208 receive_seq=4208 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999890 adj=31998465 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=44.5 th1: temp=43.6 th2: temp=44.5 th3: temp=42.8 sysload=0.19 cputime=65.371 memavail=7409192 print_time=507.958 buffer_time=2.280 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 484.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5700166 bytes_read=717355 bytes_retransmit=9 bytes_invalid=0 send_seq=101261 receive_seq=101260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=18545 freq=400015738 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3598 bytes_read=13113 bytes_retransmit=0 bytes_invalid=0 send_seq=571 receive_seq=571 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999713 adj=49997321 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=28476 bytes_read=803283 bytes_retransmit=9 bytes_invalid=0 send_seq=3660 receive_seq=3660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000176 adj=63997485 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12690 bytes_read=68415 bytes_retransmit=9 bytes_invalid=0 send_seq=1314 receive_seq=1314 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997296 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3757 bytes_read=118702 bytes_retransmit=9 bytes_invalid=0 send_seq=577 receive_seq=577 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997488 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4351 bytes_read=12887 bytes_retransmit=9 bytes_invalid=0 send_seq=572 receive_seq=572 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999410 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.6 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47427 bytes_read=380360 bytes_retransmit=0 bytes_invalid=0 send_seq=4209 receive_seq=4209 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999890 adj=31998515 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=44.5 th1: temp=43.7 th2: temp=44.5 th3: temp=42.8 sysload=0.19 cputime=65.503 memavail=7409192 print_time=509.035 buffer_time=2.356 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 485.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5712715 bytes_read=718746 bytes_retransmit=9 bytes_invalid=0 send_seq=101473 receive_seq=101473 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=19473 freq=400015722 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3604 bytes_read=13142 bytes_retransmit=0 bytes_invalid=0 send_seq=572 receive_seq=572 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999708 adj=49997392 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=28552 bytes_read=806357 bytes_retransmit=9 bytes_invalid=0 send_seq=3671 receive_seq=3671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997537 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12696 bytes_read=68515 bytes_retransmit=9 bytes_invalid=0 send_seq=1315 receive_seq=1315 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997360 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3763 bytes_read=118981 bytes_retransmit=9 bytes_invalid=0 send_seq=578 receive_seq=578 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997537 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4357 bytes_read=12903 bytes_retransmit=9 bytes_invalid=0 send_seq=573 receive_seq=573 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999419 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47433 bytes_read=380716 bytes_retransmit=0 bytes_invalid=0 send_seq=4210 receive_seq=4210 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999889 adj=31998547 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=45.1 th1: temp=43.6 th2: temp=44.7 th3: temp=42.9 sysload=0.19 cputime=65.640 memavail=7409192 print_time=510.111 buffer_time=2.432 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 486.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5725242 bytes_read=720121 bytes_retransmit=9 bytes_invalid=0 send_seq=101686 receive_seq=101686 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=20401 freq=400015692 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3610 bytes_read=13158 bytes_retransmit=0 bytes_invalid=0 send_seq=573 receive_seq=573 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999705 adj=49997440 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=28628 bytes_read=809442 bytes_retransmit=9 bytes_invalid=0 send_seq=3682 receive_seq=3682 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000176 adj=63997578 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12702 bytes_read=68643 bytes_retransmit=9 bytes_invalid=0 send_seq=1316 receive_seq=1316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997416 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3769 bytes_read=119230 bytes_retransmit=9 bytes_invalid=0 send_seq=579 receive_seq=579 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997571 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4363 bytes_read=12919 bytes_retransmit=9 bytes_invalid=0 send_seq=574 receive_seq=574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47439 bytes_read=381072 bytes_retransmit=0 bytes_invalid=0 send_seq=4211 receive_seq=4211 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999889 adj=31998573 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.011 th0: temp=44.8 th1: temp=43.7 th2: temp=44.7 th3: temp=42.8 sysload=0.18 cputime=65.771 memavail=7409192 print_time=511.188 buffer_time=2.507 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 487.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5737738 bytes_read=721510 bytes_retransmit=9 bytes_invalid=0 send_seq=101896 receive_seq=101896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=15221 freq=400015681 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3616 bytes_read=13174 bytes_retransmit=0 bytes_invalid=0 send_seq=574 receive_seq=574 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999701 adj=49997510 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=28704 bytes_read=812499 bytes_retransmit=9 bytes_invalid=0 send_seq=3693 receive_seq=3693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000176 adj=63997648 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12708 bytes_read=68743 bytes_retransmit=9 bytes_invalid=0 send_seq=1317 receive_seq=1317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997483 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3775 bytes_read=119464 bytes_retransmit=9 bytes_invalid=0 send_seq=580 receive_seq=580 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999514 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4369 bytes_read=12946 bytes_retransmit=9 bytes_invalid=0 send_seq=575 receive_seq=575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47445 bytes_read=381428 bytes_retransmit=0 bytes_invalid=0 send_seq=4212 receive_seq=4212 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999889 adj=31998610 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.011 th0: temp=44.4 th1: temp=43.6 th2: temp=45.0 th3: temp=42.8 sysload=0.18 cputime=65.895 memavail=7409192 print_time=511.726 buffer_time=2.045 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 488.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5750370 bytes_read=722890 bytes_retransmit=9 bytes_invalid=0 send_seq=102110 receive_seq=102110 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=16049 freq=400015690 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3622 bytes_read=13190 bytes_retransmit=0 bytes_invalid=0 send_seq=575 receive_seq=575 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999696 adj=49997473 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=28780 bytes_read=815555 bytes_retransmit=9 bytes_invalid=0 send_seq=3704 receive_seq=3704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000176 adj=63997678 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12714 bytes_read=68843 bytes_retransmit=9 bytes_invalid=0 send_seq=1318 receive_seq=1318 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3781 bytes_read=119758 bytes_retransmit=9 bytes_invalid=0 send_seq=581 receive_seq=581 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4375 bytes_read=12962 bytes_retransmit=9 bytes_invalid=0 send_seq=576 receive_seq=576 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47451 bytes_read=381784 bytes_retransmit=0 bytes_invalid=0 send_seq=4213 receive_seq=4213 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999890 adj=31998617 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.011 th0: temp=44.6 th1: temp=43.7 th2: temp=44.6 th3: temp=42.7 sysload=0.18 cputime=66.029 memavail=7409192 print_time=512.802 buffer_time=2.121 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 489.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5763309 bytes_read=724295 bytes_retransmit=9 bytes_invalid=0 send_seq=102329 receive_seq=102329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=16629 freq=400015670 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3628 bytes_read=13206 bytes_retransmit=0 bytes_invalid=0 send_seq=576 receive_seq=576 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999690 adj=49997428 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=28856 bytes_read=818641 bytes_retransmit=9 bytes_invalid=0 send_seq=3715 receive_seq=3715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997652 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12720 bytes_read=68985 bytes_retransmit=9 bytes_invalid=0 send_seq=1319 receive_seq=1319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3787 bytes_read=120007 bytes_retransmit=9 bytes_invalid=0 send_seq=582 receive_seq=582 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997623 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4381 bytes_read=12978 bytes_retransmit=9 bytes_invalid=0 send_seq=577 receive_seq=577 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47457 bytes_read=382140 bytes_retransmit=0 bytes_invalid=0 send_seq=4214 receive_seq=4214 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999889 adj=31998615 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=44.8 th1: temp=43.7 th2: temp=44.3 th3: temp=43.0 sysload=0.18 cputime=66.162 memavail=7409192 print_time=513.879 buffer_time=2.198 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 490.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5775791 bytes_read=725695 bytes_retransmit=9 bytes_invalid=0 send_seq=102538 receive_seq=102538 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=17574 freq=400015677 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3634 bytes_read=13235 bytes_retransmit=0 bytes_invalid=0 send_seq=577 receive_seq=577 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999689 adj=49997466 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=28932 bytes_read=821714 bytes_retransmit=9 bytes_invalid=0 send_seq=3726 receive_seq=3726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997777 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12726 bytes_read=69085 bytes_retransmit=9 bytes_invalid=0 send_seq=1320 receive_seq=1320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3793 bytes_read=120241 bytes_retransmit=9 bytes_invalid=0 send_seq=583 receive_seq=583 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999514 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4387 bytes_read=12994 bytes_retransmit=9 bytes_invalid=0 send_seq=578 receive_seq=578 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47463 bytes_read=382496 bytes_retransmit=0 bytes_invalid=0 send_seq=4215 receive_seq=4215 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999891 adj=31998635 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=44.7 th1: temp=43.7 th2: temp=44.6 th3: temp=42.7 sysload=0.18 cputime=66.296 memavail=7409220 print_time=514.955 buffer_time=2.274 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 491.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5788311 bytes_read=727055 bytes_retransmit=9 bytes_invalid=0 send_seq=102748 receive_seq=102748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=18495 freq=400015664 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3640 bytes_read=13251 bytes_retransmit=0 bytes_invalid=0 send_seq=578 receive_seq=578 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999686 adj=49997494 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=29008 bytes_read=824829 bytes_retransmit=9 bytes_invalid=0 send_seq=3737 receive_seq=3737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997733 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12732 bytes_read=69185 bytes_retransmit=9 bytes_invalid=0 send_seq=1321 receive_seq=1321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997508 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3799 bytes_read=120520 bytes_retransmit=9 bytes_invalid=0 send_seq=584 receive_seq=584 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999514 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4393 bytes_read=13010 bytes_retransmit=9 bytes_invalid=0 send_seq=579 receive_seq=579 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47469 bytes_read=382852 bytes_retransmit=0 bytes_invalid=0 send_seq=4216 receive_seq=4216 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999891 adj=31998648 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=44.7 th1: temp=43.8 th2: temp=44.5 th3: temp=42.9 sysload=0.16 cputime=66.429 memavail=7409236 print_time=516.032 buffer_time=2.350 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 492.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5800871 bytes_read=728420 bytes_retransmit=9 bytes_invalid=0 send_seq=102959 receive_seq=102959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=19390 freq=400015640 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3646 bytes_read=13267 bytes_retransmit=0 bytes_invalid=0 send_seq=579 receive_seq=579 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999682 adj=49997532 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=29077 bytes_read=827892 bytes_retransmit=9 bytes_invalid=0 send_seq=3747 receive_seq=3747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997740 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12738 bytes_read=69313 bytes_retransmit=9 bytes_invalid=0 send_seq=1322 receive_seq=1322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997516 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3805 bytes_read=120769 bytes_retransmit=9 bytes_invalid=0 send_seq=585 receive_seq=585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999514 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4399 bytes_read=13037 bytes_retransmit=9 bytes_invalid=0 send_seq=580 receive_seq=580 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47475 bytes_read=383208 bytes_retransmit=0 bytes_invalid=0 send_seq=4217 receive_seq=4217 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999891 adj=31998662 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=44.8 th1: temp=43.9 th2: temp=44.7 th3: temp=42.8 sysload=0.16 cputime=66.561 memavail=7408732 print_time=517.108 buffer_time=2.425 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 493.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5813425 bytes_read=729804 bytes_retransmit=9 bytes_invalid=0 send_seq=103169 receive_seq=103169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=20318 freq=400015621 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3652 bytes_read=13283 bytes_retransmit=0 bytes_invalid=0 send_seq=580 receive_seq=580 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999677 adj=49997563 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=29153 bytes_read=830951 bytes_retransmit=9 bytes_invalid=0 send_seq=3758 receive_seq=3758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997829 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12744 bytes_read=69413 bytes_retransmit=9 bytes_invalid=0 send_seq=1323 receive_seq=1323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3811 bytes_read=121018 bytes_retransmit=9 bytes_invalid=0 send_seq=586 receive_seq=586 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999513 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4405 bytes_read=13053 bytes_retransmit=9 bytes_invalid=0 send_seq=581 receive_seq=581 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47481 bytes_read=383564 bytes_retransmit=0 bytes_invalid=0 send_seq=4218 receive_seq=4218 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999892 adj=31998673 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.011 th0: temp=45.2 th1: temp=43.6 th2: temp=44.6 th3: temp=43.0 sysload=0.16 cputime=66.708 memavail=7409864 print_time=518.185 buffer_time=2.501 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 494.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5825943 bytes_read=731169 bytes_retransmit=9 bytes_invalid=0 send_seq=103380 receive_seq=103380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=15138 freq=400015621 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3658 bytes_read=13299 bytes_retransmit=0 bytes_invalid=0 send_seq=581 receive_seq=581 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999672 adj=49997567 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=29229 bytes_read=834023 bytes_retransmit=9 bytes_invalid=0 send_seq=3769 receive_seq=3769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997824 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12750 bytes_read=69527 bytes_retransmit=9 bytes_invalid=0 send_seq=1324 receive_seq=1324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997572 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3817 bytes_read=121297 bytes_retransmit=9 bytes_invalid=0 send_seq=587 receive_seq=587 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4411 bytes_read=13069 bytes_retransmit=9 bytes_invalid=0 send_seq=582 receive_seq=582 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47487 bytes_read=383913 bytes_retransmit=0 bytes_invalid=0 send_seq=4219 receive_seq=4219 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999891 adj=31998691 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=44.9 th1: temp=43.8 th2: temp=44.5 th3: temp=43.0 sysload=0.16 cputime=66.822 memavail=7409864 print_time=518.723 buffer_time=2.039 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 495.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5838506 bytes_read=732555 bytes_retransmit=9 bytes_invalid=0 send_seq=103592 receive_seq=103592 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=16049 freq=400015616 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000011 bytes_write=3664 bytes_read=13328 bytes_retransmit=0 bytes_invalid=0 send_seq=582 receive_seq=582 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999667 adj=49997515 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=29305 bytes_read=837111 bytes_retransmit=9 bytes_invalid=0 send_seq=3780 receive_seq=3780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997804 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12756 bytes_read=69655 bytes_retransmit=9 bytes_invalid=0 send_seq=1325 receive_seq=1325 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997558 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3823 bytes_read=121546 bytes_retransmit=9 bytes_invalid=0 send_seq=588 receive_seq=588 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997749 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4417 bytes_read=13085 bytes_retransmit=9 bytes_invalid=0 send_seq=583 receive_seq=583 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47493 bytes_read=384258 bytes_retransmit=0 bytes_invalid=0 send_seq=4220 receive_seq=4220 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999891 adj=31998684 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=45.1 th1: temp=43.8 th2: temp=44.7 th3: temp=43.1 sysload=0.16 cputime=66.958 memavail=7409156 print_time=519.799 buffer_time=2.115 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 496.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5851445 bytes_read=733979 bytes_retransmit=9 bytes_invalid=0 send_seq=103809 receive_seq=103809 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=16546 freq=400015598 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000011 bytes_write=3670 bytes_read=13344 bytes_retransmit=0 bytes_invalid=0 send_seq=583 receive_seq=583 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999662 adj=49997487 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=29381 bytes_read=840178 bytes_retransmit=9 bytes_invalid=0 send_seq=3791 receive_seq=3791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000181 adj=63997775 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12762 bytes_read=69755 bytes_retransmit=9 bytes_invalid=0 send_seq=1326 receive_seq=1326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000002 adj=63997558 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3829 bytes_read=121780 bytes_retransmit=9 bytes_invalid=0 send_seq=589 receive_seq=589 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997735 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4423 bytes_read=13101 bytes_retransmit=9 bytes_invalid=0 send_seq=584 receive_seq=584 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47499 bytes_read=384602 bytes_retransmit=0 bytes_invalid=0 send_seq=4221 receive_seq=4221 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999892 adj=31998698 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=44.9 th1: temp=43.7 th2: temp=44.8 th3: temp=43.0 sysload=0.15 cputime=67.092 memavail=7409156 print_time=520.876 buffer_time=2.191 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 497.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5864017 bytes_read=735359 bytes_retransmit=9 bytes_invalid=0 send_seq=104023 receive_seq=104023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=26 upcoming_bytes=17474 freq=400015584 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000011 bytes_write=3676 bytes_read=13360 bytes_retransmit=0 bytes_invalid=0 send_seq=584 receive_seq=584 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999659 adj=49997508 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=29457 bytes_read=843308 bytes_retransmit=9 bytes_invalid=0 send_seq=3802 receive_seq=3802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997772 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12768 bytes_read=69869 bytes_retransmit=9 bytes_invalid=0 send_seq=1327 receive_seq=1327 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000001 adj=63997573 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=3835 bytes_read=122059 bytes_retransmit=9 bytes_invalid=0 send_seq=590 receive_seq=590 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997744 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4429 bytes_read=13128 bytes_retransmit=9 bytes_invalid=0 send_seq=585 receive_seq=585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47505 bytes_read=384947 bytes_retransmit=0 bytes_invalid=0 send_seq=4222 receive_seq=4222 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998724 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=44.8 th1: temp=43.7 th2: temp=44.9 th3: temp=42.8 sysload=0.15 cputime=67.228 memavail=7409156 print_time=521.952 buffer_time=2.267 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 498.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5876542 bytes_read=736724 bytes_retransmit=9 bytes_invalid=0 send_seq=104234 receive_seq=104234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=18395 freq=400015584 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000011 bytes_write=3682 bytes_read=13376 bytes_retransmit=0 bytes_invalid=0 send_seq=585 receive_seq=585 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999655 adj=49997532 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=29533 bytes_read=846496 bytes_retransmit=9 bytes_invalid=0 send_seq=3813 receive_seq=3813 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000179 adj=63997766 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12774 bytes_read=69983 bytes_retransmit=9 bytes_invalid=0 send_seq=1328 receive_seq=1328 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000001 adj=63997574 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3841 bytes_read=122323 bytes_retransmit=9 bytes_invalid=0 send_seq=591 receive_seq=591 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997755 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4435 bytes_read=13144 bytes_retransmit=9 bytes_invalid=0 send_seq=586 receive_seq=586 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47511 bytes_read=385292 bytes_retransmit=0 bytes_invalid=0 send_seq=4223 receive_seq=4223 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998729 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=45.2 th1: temp=43.7 th2: temp=44.7 th3: temp=43.0 sysload=0.15 cputime=67.365 memavail=7409156 print_time=523.029 buffer_time=2.342 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 499.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5889112 bytes_read=738128 bytes_retransmit=9 bytes_invalid=0 send_seq=104447 receive_seq=104447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=19323 freq=400015575 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000011 bytes_write=3688 bytes_read=13392 bytes_retransmit=0 bytes_invalid=0 send_seq=586 receive_seq=586 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999652 adj=49997532 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=29609 bytes_read=849611 bytes_retransmit=9 bytes_invalid=0 send_seq=3824 receive_seq=3824 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997733 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12780 bytes_read=70097 bytes_retransmit=9 bytes_invalid=0 send_seq=1329 receive_seq=1329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000000 adj=63997552 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3847 bytes_read=122557 bytes_retransmit=9 bytes_invalid=0 send_seq=592 receive_seq=592 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997735 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4441 bytes_read=13160 bytes_retransmit=9 bytes_invalid=0 send_seq=587 receive_seq=587 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47517 bytes_read=385637 bytes_retransmit=0 bytes_invalid=0 send_seq=4224 receive_seq=4224 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998714 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=45.0 th1: temp=43.9 th2: temp=44.6 th3: temp=43.1 sysload=0.15 cputime=67.496 memavail=7409156 print_time=524.105 buffer_time=2.418 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 500.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5901619 bytes_read=739514 bytes_retransmit=9 bytes_invalid=0 send_seq=104659 receive_seq=104659 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=20251 freq=400015587 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3694 bytes_read=13421 bytes_retransmit=0 bytes_invalid=0 send_seq=587 receive_seq=587 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999648 adj=49997542 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=29685 bytes_read=852756 bytes_retransmit=9 bytes_invalid=0 send_seq=3835 receive_seq=3835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997748 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12786 bytes_read=70211 bytes_retransmit=9 bytes_invalid=0 send_seq=1330 receive_seq=1330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000000 adj=63997553 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3853 bytes_read=122836 bytes_retransmit=9 bytes_invalid=0 send_seq=593 receive_seq=593 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997728 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4447 bytes_read=13176 bytes_retransmit=9 bytes_invalid=0 send_seq=588 receive_seq=588 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47523 bytes_read=385982 bytes_retransmit=0 bytes_invalid=0 send_seq=4225 receive_seq=4225 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999895 adj=31998710 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=44.8 th1: temp=43.7 th2: temp=44.7 th3: temp=42.8 sysload=0.15 cputime=67.627 memavail=7409156 print_time=525.182 buffer_time=2.495 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 501.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5914129 bytes_read=740889 bytes_retransmit=9 bytes_invalid=0 send_seq=104872 receive_seq=104872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=15071 freq=400015616 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3700 bytes_read=13437 bytes_retransmit=0 bytes_invalid=0 send_seq=588 receive_seq=588 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999643 adj=49997519 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=29761 bytes_read=855887 bytes_retransmit=9 bytes_invalid=0 send_seq=3846 receive_seq=3846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997715 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12792 bytes_read=70325 bytes_retransmit=9 bytes_invalid=0 send_seq=1331 receive_seq=1331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999999 adj=63997515 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3859 bytes_read=123085 bytes_retransmit=9 bytes_invalid=0 send_seq=594 receive_seq=594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4453 bytes_read=13192 bytes_retransmit=9 bytes_invalid=0 send_seq=589 receive_seq=589 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47529 bytes_read=386327 bytes_retransmit=0 bytes_invalid=0 send_seq=4226 receive_seq=4226 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999895 adj=31998705 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=45.0 th1: temp=43.9 th2: temp=44.8 th3: temp=42.9 sysload=0.14 cputime=67.741 memavail=7409156 print_time=525.720 buffer_time=2.033 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 502.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5926651 bytes_read=742288 bytes_retransmit=9 bytes_invalid=0 send_seq=105084 receive_seq=105084 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=16016 freq=400015600 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3706 bytes_read=13453 bytes_retransmit=0 bytes_invalid=0 send_seq=589 receive_seq=589 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999639 adj=49997421 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=29837 bytes_read=859004 bytes_retransmit=9 bytes_invalid=0 send_seq=3857 receive_seq=3857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000177 adj=63997645 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12798 bytes_read=70425 bytes_retransmit=9 bytes_invalid=0 send_seq=1332 receive_seq=1332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999999 adj=63997451 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3865 bytes_read=123319 bytes_retransmit=9 bytes_invalid=0 send_seq=595 receive_seq=595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997722 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4459 bytes_read=13219 bytes_retransmit=9 bytes_invalid=0 send_seq=590 receive_seq=590 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47535 bytes_read=386674 bytes_retransmit=0 bytes_invalid=0 send_seq=4227 receive_seq=4227 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998670 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=45.1 th1: temp=43.8 th2: temp=44.8 th3: temp=43.2 sysload=0.14 cputime=67.871 memavail=7409156 print_time=526.796 buffer_time=2.109 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 503.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5939695 bytes_read=743698 bytes_retransmit=9 bytes_invalid=0 send_seq=105304 receive_seq=105304 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=16463 freq=400015594 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3712 bytes_read=13469 bytes_retransmit=0 bytes_invalid=0 send_seq=590 receive_seq=590 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999636 adj=49997428 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=29913 bytes_read=862132 bytes_retransmit=9 bytes_invalid=0 send_seq=3868 receive_seq=3868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000177 adj=63997669 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12804 bytes_read=70539 bytes_retransmit=9 bytes_invalid=0 send_seq=1333 receive_seq=1333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3871 bytes_read=123613 bytes_retransmit=9 bytes_invalid=0 send_seq=596 receive_seq=596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997724 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4465 bytes_read=13235 bytes_retransmit=9 bytes_invalid=0 send_seq=591 receive_seq=591 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47541 bytes_read=387030 bytes_retransmit=0 bytes_invalid=0 send_seq=4228 receive_seq=4228 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998674 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=44.9 th1: temp=43.8 th2: temp=45.0 th3: temp=43.1 sysload=0.14 cputime=68.003 memavail=7409156 print_time=527.873 buffer_time=2.184 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 504.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5952221 bytes_read=745058 bytes_retransmit=9 bytes_invalid=0 send_seq=105515 receive_seq=105515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=17391 freq=400015593 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3718 bytes_read=13485 bytes_retransmit=0 bytes_invalid=0 send_seq=591 receive_seq=591 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999633 adj=49997458 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=29982 bytes_read=865237 bytes_retransmit=9 bytes_invalid=0 send_seq=3878 receive_seq=3878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000176 adj=63997681 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12810 bytes_read=70667 bytes_retransmit=9 bytes_invalid=0 send_seq=1334 receive_seq=1334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3877 bytes_read=123862 bytes_retransmit=9 bytes_invalid=0 send_seq=597 receive_seq=597 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999523 adj=47997717 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4471 bytes_read=13251 bytes_retransmit=9 bytes_invalid=0 send_seq=592 receive_seq=592 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47547 bytes_read=387386 bytes_retransmit=0 bytes_invalid=0 send_seq=4229 receive_seq=4229 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998669 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=45.0 th1: temp=43.9 th2: temp=45.0 th3: temp=43.2 sysload=0.14 cputime=68.135 memavail=7409156 print_time=528.949 buffer_time=2.260 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 505.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5964778 bytes_read=746468 bytes_retransmit=9 bytes_invalid=0 send_seq=105726 receive_seq=105726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=22 upcoming_bytes=18316 freq=400015589 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3724 bytes_read=13514 bytes_retransmit=0 bytes_invalid=0 send_seq=592 receive_seq=592 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999630 adj=49997474 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=30058 bytes_read=868426 bytes_retransmit=9 bytes_invalid=0 send_seq=3889 receive_seq=3889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997676 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12816 bytes_read=70767 bytes_retransmit=9 bytes_invalid=0 send_seq=1335 receive_seq=1335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999999 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3883 bytes_read=124096 bytes_retransmit=9 bytes_invalid=0 send_seq=598 receive_seq=598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999523 adj=47997695 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4477 bytes_read=13267 bytes_retransmit=9 bytes_invalid=0 send_seq=593 receive_seq=593 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47553 bytes_read=387742 bytes_retransmit=0 bytes_invalid=0 send_seq=4230 receive_seq=4230 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998667 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=44.8 th1: temp=43.9 th2: temp=44.8 th3: temp=43.2 sysload=0.14 cputime=68.270 memavail=7408192 print_time=530.026 buffer_time=2.336 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 506.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5977288 bytes_read=747833 bytes_retransmit=9 bytes_invalid=0 send_seq=105937 receive_seq=105937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=19241 freq=400015608 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3730 bytes_read=13530 bytes_retransmit=0 bytes_invalid=0 send_seq=593 receive_seq=593 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999626 adj=49997488 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=30134 bytes_read=871554 bytes_retransmit=9 bytes_invalid=0 send_seq=3900 receive_seq=3900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997670 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12822 bytes_read=70881 bytes_retransmit=9 bytes_invalid=0 send_seq=1336 receive_seq=1336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997515 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3889 bytes_read=124390 bytes_retransmit=9 bytes_invalid=0 send_seq=599 receive_seq=599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999522 adj=47997682 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4483 bytes_read=13283 bytes_retransmit=9 bytes_invalid=0 send_seq=594 receive_seq=594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47559 bytes_read=388098 bytes_retransmit=0 bytes_invalid=0 send_seq=4231 receive_seq=4231 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999895 adj=31998672 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=45.0 th1: temp=43.9 th2: temp=44.8 th3: temp=42.9 sysload=0.13 cputime=68.401 memavail=7408192 print_time=531.102 buffer_time=2.412 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 507.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=5989830 bytes_read=749198 bytes_retransmit=9 bytes_invalid=0 send_seq=106148 receive_seq=106148 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=20169 freq=400015608 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3736 bytes_read=13546 bytes_retransmit=0 bytes_invalid=0 send_seq=594 receive_seq=594 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999623 adj=49997464 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=30210 bytes_read=874685 bytes_retransmit=9 bytes_invalid=0 send_seq=3911 receive_seq=3911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997641 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12828 bytes_read=70995 bytes_retransmit=9 bytes_invalid=0 send_seq=1337 receive_seq=1337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997473 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3895 bytes_read=124624 bytes_retransmit=9 bytes_invalid=0 send_seq=600 receive_seq=600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999523 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4489 bytes_read=13310 bytes_retransmit=9 bytes_invalid=0 send_seq=595 receive_seq=595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47565 bytes_read=388454 bytes_retransmit=0 bytes_invalid=0 send_seq=4232 receive_seq=4232 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998657 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=45.1 th1: temp=43.9 th2: temp=44.8 th3: temp=43.1 sysload=0.13 cputime=68.531 memavail=7408192 print_time=532.179 buffer_time=2.488 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 508.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6002375 bytes_read=750602 bytes_retransmit=9 bytes_invalid=0 send_seq=106361 receive_seq=106361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=14989 freq=400015640 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3742 bytes_read=13562 bytes_retransmit=0 bytes_invalid=0 send_seq=595 receive_seq=595 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999621 adj=49997473 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=30286 bytes_read=877799 bytes_retransmit=9 bytes_invalid=0 send_seq=3922 receive_seq=3922 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000174 adj=63997641 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12834 bytes_read=71095 bytes_retransmit=9 bytes_invalid=0 send_seq=1338 receive_seq=1338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999999 adj=63997472 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3901 bytes_read=124873 bytes_retransmit=9 bytes_invalid=0 send_seq=601 receive_seq=601 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999522 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4495 bytes_read=13326 bytes_retransmit=9 bytes_invalid=0 send_seq=596 receive_seq=596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47571 bytes_read=388810 bytes_retransmit=0 bytes_invalid=0 send_seq=4233 receive_seq=4233 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998648 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.011 th0: temp=44.7 th1: temp=43.8 th2: temp=44.6 th3: temp=43.2 sysload=0.13 cputime=68.658 memavail=7407396 print_time=532.717 buffer_time=2.025 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 509.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6014881 bytes_read=751947 bytes_retransmit=9 bytes_invalid=0 send_seq=106568 receive_seq=106568 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=15917 freq=400015619 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3748 bytes_read=13578 bytes_retransmit=0 bytes_invalid=0 send_seq=596 receive_seq=596 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999617 adj=49997401 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=30362 bytes_read=880928 bytes_retransmit=9 bytes_invalid=0 send_seq=3933 receive_seq=3933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000174 adj=63997577 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12840 bytes_read=71223 bytes_retransmit=9 bytes_invalid=0 send_seq=1339 receive_seq=1339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997428 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3907 bytes_read=125167 bytes_retransmit=9 bytes_invalid=0 send_seq=602 receive_seq=602 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999522 adj=47997594 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4501 bytes_read=13342 bytes_retransmit=9 bytes_invalid=0 send_seq=597 receive_seq=597 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47577 bytes_read=389166 bytes_retransmit=0 bytes_invalid=0 send_seq=4234 receive_seq=4234 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998619 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=45.1 th1: temp=43.8 th2: temp=45.1 th3: temp=42.9 sysload=0.13 cputime=68.806 memavail=7407152 print_time=533.794 buffer_time=2.102 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 510.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6027878 bytes_read=753368 bytes_retransmit=9 bytes_invalid=0 send_seq=106787 receive_seq=106787 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=16381 freq=400015623 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3754 bytes_read=13607 bytes_retransmit=0 bytes_invalid=0 send_seq=597 receive_seq=597 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999614 adj=49997417 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=30438 bytes_read=884072 bytes_retransmit=9 bytes_invalid=0 send_seq=3944 receive_seq=3944 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000173 adj=63997623 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12846 bytes_read=71337 bytes_retransmit=9 bytes_invalid=0 send_seq=1340 receive_seq=1340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997473 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3913 bytes_read=125401 bytes_retransmit=9 bytes_invalid=0 send_seq=603 receive_seq=603 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4507 bytes_read=13358 bytes_retransmit=9 bytes_invalid=0 send_seq=598 receive_seq=598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47583 bytes_read=389522 bytes_retransmit=0 bytes_invalid=0 send_seq=4235 receive_seq=4235 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998642 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=45.0 th1: temp=43.8 th2: temp=44.5 th3: temp=43.0 sysload=0.13 cputime=68.957 memavail=7406804 print_time=534.870 buffer_time=2.177 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 511.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6040442 bytes_read=754767 bytes_retransmit=9 bytes_invalid=0 send_seq=106999 receive_seq=106999 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=17309 freq=400015626 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3760 bytes_read=13623 bytes_retransmit=0 bytes_invalid=0 send_seq=598 receive_seq=598 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999614 adj=49997430 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=30514 bytes_read=887186 bytes_retransmit=9 bytes_invalid=0 send_seq=3955 receive_seq=3955 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000172 adj=63997622 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12852 bytes_read=71437 bytes_retransmit=9 bytes_invalid=0 send_seq=1341 receive_seq=1341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997465 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3919 bytes_read=125635 bytes_retransmit=9 bytes_invalid=0 send_seq=604 receive_seq=604 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4513 bytes_read=13374 bytes_retransmit=9 bytes_invalid=0 send_seq=599 receive_seq=599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999908 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47589 bytes_read=389878 bytes_retransmit=0 bytes_invalid=0 send_seq=4236 receive_seq=4236 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999895 adj=31998634 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=44.8 th1: temp=43.9 th2: temp=45.0 th3: temp=43.3 sysload=0.12 cputime=69.091 memavail=7406816 print_time=535.946 buffer_time=2.253 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 512.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6052980 bytes_read=756142 bytes_retransmit=9 bytes_invalid=0 send_seq=107212 receive_seq=107212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=18237 freq=400015610 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3766 bytes_read=13639 bytes_retransmit=0 bytes_invalid=0 send_seq=599 receive_seq=599 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999611 adj=49997475 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=30590 bytes_read=890314 bytes_retransmit=9 bytes_invalid=0 send_seq=3966 receive_seq=3966 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000172 adj=63997619 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12858 bytes_read=71551 bytes_retransmit=9 bytes_invalid=0 send_seq=1342 receive_seq=1342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997462 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3925 bytes_read=125929 bytes_retransmit=9 bytes_invalid=0 send_seq=605 receive_seq=605 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4519 bytes_read=13401 bytes_retransmit=9 bytes_invalid=0 send_seq=600 receive_seq=600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47595 bytes_read=390234 bytes_retransmit=0 bytes_invalid=0 send_seq=4237 receive_seq=4237 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999895 adj=31998654 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=44.9 th1: temp=43.9 th2: temp=44.8 th3: temp=43.1 sysload=0.12 cputime=69.226 memavail=7406816 print_time=537.023 buffer_time=2.329 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 513.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6065529 bytes_read=757517 bytes_retransmit=9 bytes_invalid=0 send_seq=107425 receive_seq=107425 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=19158 freq=400015587 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3772 bytes_read=13655 bytes_retransmit=0 bytes_invalid=0 send_seq=600 receive_seq=600 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999607 adj=49997505 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=30666 bytes_read=893494 bytes_retransmit=9 bytes_invalid=0 send_seq=3977 receive_seq=3977 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000172 adj=63997656 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12864 bytes_read=71661 bytes_retransmit=9 bytes_invalid=0 send_seq=1343 receive_seq=1343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997494 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3931 bytes_read=126162 bytes_retransmit=9 bytes_invalid=0 send_seq=606 receive_seq=606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4525 bytes_read=13417 bytes_retransmit=9 bytes_invalid=0 send_seq=601 receive_seq=601 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47601 bytes_read=390590 bytes_retransmit=0 bytes_invalid=0 send_seq=4238 receive_seq=4238 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999895 adj=31998660 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=45.0 th1: temp=44.1 th2: temp=45.2 th3: temp=43.2 sysload=0.12 cputime=69.365 memavail=7405820 print_time=538.099 buffer_time=2.405 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 514.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6078026 bytes_read=758914 bytes_retransmit=9 bytes_invalid=0 send_seq=107637 receive_seq=107637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=20086 freq=400015646 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3778 bytes_read=13671 bytes_retransmit=0 bytes_invalid=0 send_seq=601 receive_seq=601 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999605 adj=49997530 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=30742 bytes_read=896591 bytes_retransmit=9 bytes_invalid=0 send_seq=3988 receive_seq=3988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000172 adj=63997696 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12870 bytes_read=71767 bytes_retransmit=9 bytes_invalid=0 send_seq=1344 receive_seq=1344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3937 bytes_read=126377 bytes_retransmit=9 bytes_invalid=0 send_seq=607 receive_seq=607 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4531 bytes_read=13433 bytes_retransmit=9 bytes_invalid=0 send_seq=602 receive_seq=602 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47607 bytes_read=390946 bytes_retransmit=0 bytes_invalid=0 send_seq=4239 receive_seq=4239 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998675 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=45.1 th1: temp=43.8 th2: temp=45.0 th3: temp=43.3 sysload=0.12 cputime=69.495 memavail=7405820 print_time=539.176 buffer_time=2.481 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 515.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6090591 bytes_read=760297 bytes_retransmit=9 bytes_invalid=0 send_seq=107849 receive_seq=107849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=14906 freq=400015639 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=3784 bytes_read=13700 bytes_retransmit=0 bytes_invalid=0 send_seq=602 receive_seq=602 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999602 adj=49997459 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=30818 bytes_read=899717 bytes_retransmit=9 bytes_invalid=0 send_seq=3999 receive_seq=3999 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000172 adj=63997590 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12876 bytes_read=71873 bytes_retransmit=9 bytes_invalid=0 send_seq=1345 receive_seq=1345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997434 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3943 bytes_read=126651 bytes_retransmit=9 bytes_invalid=0 send_seq=608 receive_seq=608 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997583 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4537 bytes_read=13449 bytes_retransmit=9 bytes_invalid=0 send_seq=603 receive_seq=603 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47613 bytes_read=391302 bytes_retransmit=0 bytes_invalid=0 send_seq=4240 receive_seq=4240 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998611 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=44.8 th1: temp=44.1 th2: temp=44.7 th3: temp=43.2 sysload=0.12 cputime=69.614 memavail=7405864 print_time=539.714 buffer_time=2.019 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 516.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6103104 bytes_read=761657 bytes_retransmit=9 bytes_invalid=0 send_seq=108059 receive_seq=108059 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=15801 freq=400015631 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=3790 bytes_read=13716 bytes_retransmit=0 bytes_invalid=0 send_seq=603 receive_seq=603 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999600 adj=49997430 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=30887 bytes_read=902805 bytes_retransmit=9 bytes_invalid=0 send_seq=4009 receive_seq=4009 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000171 adj=63997605 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12882 bytes_read=71979 bytes_retransmit=9 bytes_invalid=0 send_seq=1346 receive_seq=1346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997442 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3949 bytes_read=126869 bytes_retransmit=9 bytes_invalid=0 send_seq=609 receive_seq=609 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997585 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4543 bytes_read=13465 bytes_retransmit=9 bytes_invalid=0 send_seq=604 receive_seq=604 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47619 bytes_read=391658 bytes_retransmit=0 bytes_invalid=0 send_seq=4241 receive_seq=4241 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998616 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=45.1 th1: temp=44.1 th2: temp=45.0 th3: temp=42.8 sysload=0.11 cputime=69.745 memavail=7405864 print_time=540.791 buffer_time=2.093 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 517.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6116222 bytes_read=763096 bytes_retransmit=9 bytes_invalid=0 send_seq=108279 receive_seq=108279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=16231 freq=400015621 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=3796 bytes_read=13732 bytes_retransmit=0 bytes_invalid=0 send_seq=604 receive_seq=604 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999597 adj=49997440 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=30963 bytes_read=905903 bytes_retransmit=9 bytes_invalid=0 send_seq=4020 receive_seq=4020 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000173 adj=63997623 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12888 bytes_read=72074 bytes_retransmit=9 bytes_invalid=0 send_seq=1347 receive_seq=1347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999997 adj=63997463 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3955 bytes_read=127087 bytes_retransmit=9 bytes_invalid=0 send_seq=610 receive_seq=610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997604 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4549 bytes_read=13492 bytes_retransmit=9 bytes_invalid=0 send_seq=605 receive_seq=605 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47625 bytes_read=392014 bytes_retransmit=0 bytes_invalid=0 send_seq=4242 receive_seq=4242 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998620 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=45.0 th1: temp=43.6 th2: temp=44.6 th3: temp=43.2 sysload=0.11 cputime=69.877 memavail=7405864 print_time=541.867 buffer_time=2.166 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 518.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6128705 bytes_read=764411 bytes_retransmit=9 bytes_invalid=0 send_seq=108480 receive_seq=108480 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=17143 freq=400015634 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=3802 bytes_read=13748 bytes_retransmit=0 bytes_invalid=0 send_seq=605 receive_seq=605 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999596 adj=49997472 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=31039 bytes_read=909090 bytes_retransmit=9 bytes_invalid=0 send_seq=4031 receive_seq=4031 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997668 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12894 bytes_read=72188 bytes_retransmit=9 bytes_invalid=0 send_seq=1348 receive_seq=1348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999999 adj=63997488 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3961 bytes_read=127380 bytes_retransmit=9 bytes_invalid=0 send_seq=611 receive_seq=611 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4555 bytes_read=13508 bytes_retransmit=9 bytes_invalid=0 send_seq=606 receive_seq=606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47631 bytes_read=392370 bytes_retransmit=0 bytes_invalid=0 send_seq=4243 receive_seq=4243 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998636 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.011 th0: temp=45.0 th1: temp=44.1 th2: temp=45.0 th3: temp=43.4 sysload=0.11 cputime=70.007 memavail=7405864 print_time=542.944 buffer_time=2.239 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 519.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6141219 bytes_read=765771 bytes_retransmit=9 bytes_invalid=0 send_seq=108690 receive_seq=108690 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=18071 freq=400015606 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=3808 bytes_read=13764 bytes_retransmit=0 bytes_invalid=0 send_seq=606 receive_seq=606 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999594 adj=49997472 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=31115 bytes_read=912219 bytes_retransmit=9 bytes_invalid=0 send_seq=4042 receive_seq=4042 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000176 adj=63997678 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12900 bytes_read=72316 bytes_retransmit=9 bytes_invalid=0 send_seq=1349 receive_seq=1349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999999 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3967 bytes_read=127614 bytes_retransmit=9 bytes_invalid=0 send_seq=612 receive_seq=612 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997613 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4561 bytes_read=13524 bytes_retransmit=9 bytes_invalid=0 send_seq=607 receive_seq=607 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47637 bytes_read=392726 bytes_retransmit=0 bytes_invalid=0 send_seq=4244 receive_seq=4244 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999892 adj=31998621 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.011 th0: temp=45.2 th1: temp=43.9 th2: temp=45.1 th3: temp=43.1 sysload=0.11 cputime=70.131 memavail=7405864 print_time=544.020 buffer_time=2.315 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 520.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=6153756 bytes_read=767186 bytes_retransmit=9 bytes_invalid=0 send_seq=108902 receive_seq=108902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=18992 freq=400015594 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3814 bytes_read=13793 bytes_retransmit=0 bytes_invalid=0 send_seq=607 receive_seq=607 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999591 adj=49997530 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=31191 bytes_read=915351 bytes_retransmit=9 bytes_invalid=0 send_seq=4053 receive_seq=4053 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997732 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12906 bytes_read=72416 bytes_retransmit=9 bytes_invalid=0 send_seq=1350 receive_seq=1350 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3973 bytes_read=127848 bytes_retransmit=9 bytes_invalid=0 send_seq=613 receive_seq=613 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4567 bytes_read=13540 bytes_retransmit=9 bytes_invalid=0 send_seq=608 receive_seq=608 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47643 bytes_read=393082 bytes_retransmit=0 bytes_invalid=0 send_seq=4245 receive_seq=4245 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999898 adj=31998647 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.011 th0: temp=45.2 th1: temp=44.1 th2: temp=44.9 th3: temp=43.3 sysload=0.11 cputime=70.259 memavail=7405864 print_time=545.096 buffer_time=2.391 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 521.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=6166261 bytes_read=768546 bytes_retransmit=9 bytes_invalid=0 send_seq=109112 receive_seq=109112 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=19920 freq=400015586 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3820 bytes_read=13809 bytes_retransmit=0 bytes_invalid=0 send_seq=608 receive_seq=608 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999588 adj=49997539 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=31267 bytes_read=918492 bytes_retransmit=9 bytes_invalid=0 send_seq=4064 receive_seq=4064 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997741 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12912 bytes_read=72530 bytes_retransmit=9 bytes_invalid=0 send_seq=1351 receive_seq=1351 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999999 adj=63997549 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3979 bytes_read=128142 bytes_retransmit=9 bytes_invalid=0 send_seq=614 receive_seq=614 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4573 bytes_read=13556 bytes_retransmit=9 bytes_invalid=0 send_seq=609 receive_seq=609 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47649 bytes_read=393438 bytes_retransmit=0 bytes_invalid=0 send_seq=4246 receive_seq=4246 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999899 adj=31998724 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=45.1 th1: temp=44.0 th2: temp=45.0 th3: temp=43.3 sysload=0.34 cputime=70.386 memavail=7405864 print_time=546.173 buffer_time=2.467 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 522.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=6178802 bytes_read=769926 bytes_retransmit=9 bytes_invalid=0 send_seq=109326 receive_seq=109326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=14723 freq=400015569 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3826 bytes_read=13825 bytes_retransmit=0 bytes_invalid=0 send_seq=609 receive_seq=609 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999585 adj=49997539 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=31343 bytes_read=921605 bytes_retransmit=9 bytes_invalid=0 send_seq=4075 receive_seq=4075 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997847 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12918 bytes_read=72644 bytes_retransmit=9 bytes_invalid=0 send_seq=1352 receive_seq=1352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997556 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=3985 bytes_read=128376 bytes_retransmit=9 bytes_invalid=0 send_seq=615 receive_seq=615 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4579 bytes_read=13583 bytes_retransmit=9 bytes_invalid=0 send_seq=610 receive_seq=610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47655 bytes_read=393794 bytes_retransmit=0 bytes_invalid=0 send_seq=4247 receive_seq=4247 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999898 adj=31998721 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=45.3 th1: temp=44.4 th2: temp=45.3 th3: temp=43.3 sysload=0.34 cputime=70.503 memavail=7405864 print_time=546.711 buffer_time=2.005 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 523.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=6191349 bytes_read=771315 bytes_retransmit=9 bytes_invalid=0 send_seq=109536 receive_seq=109536 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=15668 freq=400015554 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3832 bytes_read=13841 bytes_retransmit=0 bytes_invalid=0 send_seq=610 receive_seq=610 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999582 adj=49997530 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=31419 bytes_read=924719 bytes_retransmit=9 bytes_invalid=0 send_seq=4086 receive_seq=4086 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997862 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=12924 bytes_read=72744 bytes_retransmit=9 bytes_invalid=0 send_seq=1353 receive_seq=1353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999999 adj=63997585 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3991 bytes_read=128625 bytes_retransmit=9 bytes_invalid=0 send_seq=616 receive_seq=616 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4585 bytes_read=13599 bytes_retransmit=9 bytes_invalid=0 send_seq=611 receive_seq=611 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47661 bytes_read=394150 bytes_retransmit=0 bytes_invalid=0 send_seq=4248 receive_seq=4248 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999898 adj=31998727 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=45.2 th1: temp=44.4 th2: temp=44.8 th3: temp=43.3 sysload=0.34 cputime=70.632 memavail=7405864 print_time=547.788 buffer_time=2.081 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 524.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=6204305 bytes_read=772705 bytes_retransmit=9 bytes_invalid=0 send_seq=109752 receive_seq=109752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=16149 freq=400015543 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3838 bytes_read=13856 bytes_retransmit=0 bytes_invalid=0 send_seq=611 receive_seq=611 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999580 adj=49997534 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=31495 bytes_read=927862 bytes_retransmit=9 bytes_invalid=0 send_seq=4097 receive_seq=4097 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997863 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12930 bytes_read=72886 bytes_retransmit=9 bytes_invalid=0 send_seq=1354 receive_seq=1354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999999 adj=63997616 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=3997 bytes_read=128919 bytes_retransmit=9 bytes_invalid=0 send_seq=617 receive_seq=617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997701 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4591 bytes_read=13615 bytes_retransmit=9 bytes_invalid=0 send_seq=612 receive_seq=612 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47667 bytes_read=394506 bytes_retransmit=0 bytes_invalid=0 send_seq=4249 receive_seq=4249 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999897 adj=31998727 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=45.3 th1: temp=44.0 th2: temp=45.2 th3: temp=43.4 sysload=0.34 cputime=70.765 memavail=7405864 print_time=548.864 buffer_time=2.157 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 525.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6216844 bytes_read=774088 bytes_retransmit=9 bytes_invalid=0 send_seq=109964 receive_seq=109964 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=17077 freq=400015545 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3844 bytes_read=13884 bytes_retransmit=0 bytes_invalid=0 send_seq=612 receive_seq=612 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999578 adj=49997545 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=31571 bytes_read=930996 bytes_retransmit=9 bytes_invalid=0 send_seq=4108 receive_seq=4108 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997861 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12936 bytes_read=72986 bytes_retransmit=9 bytes_invalid=0 send_seq=1355 receive_seq=1355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997608 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4003 bytes_read=129153 bytes_retransmit=9 bytes_invalid=0 send_seq=618 receive_seq=618 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997712 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4597 bytes_read=13631 bytes_retransmit=9 bytes_invalid=0 send_seq=613 receive_seq=613 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47673 bytes_read=394862 bytes_retransmit=0 bytes_invalid=0 send_seq=4250 receive_seq=4250 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999897 adj=31998716 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=45.3 th1: temp=44.2 th2: temp=44.8 th3: temp=43.3 sysload=0.34 cputime=70.903 memavail=7406320 print_time=549.941 buffer_time=2.233 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 526.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6229385 bytes_read=775469 bytes_retransmit=9 bytes_invalid=0 send_seq=110173 receive_seq=110173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=18005 freq=400015567 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3850 bytes_read=13899 bytes_retransmit=0 bytes_invalid=0 send_seq=613 receive_seq=613 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999576 adj=49997538 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=31647 bytes_read=934171 bytes_retransmit=9 bytes_invalid=0 send_seq=4119 receive_seq=4119 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997810 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12942 bytes_read=73086 bytes_retransmit=9 bytes_invalid=0 send_seq=1356 receive_seq=1356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999998 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4009 bytes_read=129387 bytes_retransmit=9 bytes_invalid=0 send_seq=619 receive_seq=619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997697 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4603 bytes_read=13647 bytes_retransmit=9 bytes_invalid=0 send_seq=614 receive_seq=614 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47679 bytes_read=395218 bytes_retransmit=0 bytes_invalid=0 send_seq=4251 receive_seq=4251 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999897 adj=31998696 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=45.3 th1: temp=44.2 th2: temp=45.2 th3: temp=43.4 sysload=0.55 cputime=71.038 memavail=7406528 print_time=551.017 buffer_time=2.309 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 527.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6241885 bytes_read=776834 bytes_retransmit=9 bytes_invalid=0 send_seq=110384 receive_seq=110384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=18926 freq=400015565 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3856 bytes_read=13914 bytes_retransmit=0 bytes_invalid=0 send_seq=614 receive_seq=614 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999578 adj=49997511 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=31723 bytes_read=937315 bytes_retransmit=9 bytes_invalid=0 send_seq=4130 receive_seq=4130 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997744 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12948 bytes_read=73214 bytes_retransmit=9 bytes_invalid=0 send_seq=1357 receive_seq=1357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997517 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4015 bytes_read=129681 bytes_retransmit=9 bytes_invalid=0 send_seq=620 receive_seq=620 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4609 bytes_read=13674 bytes_retransmit=9 bytes_invalid=0 send_seq=615 receive_seq=615 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47685 bytes_read=395574 bytes_retransmit=0 bytes_invalid=0 send_seq=4252 receive_seq=4252 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999899 adj=31998671 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=45.2 th1: temp=44.2 th2: temp=45.1 th3: temp=43.4 sysload=0.55 cputime=71.179 memavail=7401532 print_time=552.093 buffer_time=2.385 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 528.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6254467 bytes_read=778214 bytes_retransmit=9 bytes_invalid=0 send_seq=110598 receive_seq=110598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=19854 freq=400015565 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3862 bytes_read=13929 bytes_retransmit=0 bytes_invalid=0 send_seq=615 receive_seq=615 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999574 adj=49997552 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=31792 bytes_read=940405 bytes_retransmit=9 bytes_invalid=0 send_seq=4140 receive_seq=4140 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997732 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12954 bytes_read=73314 bytes_retransmit=9 bytes_invalid=0 send_seq=1358 receive_seq=1358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997577 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4021 bytes_read=129930 bytes_retransmit=9 bytes_invalid=0 send_seq=621 receive_seq=621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4615 bytes_read=13690 bytes_retransmit=9 bytes_invalid=0 send_seq=616 receive_seq=616 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47691 bytes_read=395930 bytes_retransmit=0 bytes_invalid=0 send_seq=4253 receive_seq=4253 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999899 adj=31998686 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.011 th0: temp=45.2 th1: temp=44.0 th2: temp=45.3 th3: temp=43.5 sysload=0.55 cputime=71.313 memavail=7407440 print_time=553.170 buffer_time=2.461 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 529.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6267018 bytes_read=779633 bytes_retransmit=9 bytes_invalid=0 send_seq=110814 receive_seq=110814 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=14674 freq=400015568 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3868 bytes_read=13945 bytes_retransmit=0 bytes_invalid=0 send_seq=616 receive_seq=616 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999572 adj=49997526 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=31868 bytes_read=943521 bytes_retransmit=9 bytes_invalid=0 send_seq=4151 receive_seq=4151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000181 adj=63997720 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12960 bytes_read=73414 bytes_retransmit=9 bytes_invalid=0 send_seq=1359 receive_seq=1359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997560 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4027 bytes_read=130164 bytes_retransmit=9 bytes_invalid=0 send_seq=622 receive_seq=622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4621 bytes_read=13706 bytes_retransmit=9 bytes_invalid=0 send_seq=617 receive_seq=617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47697 bytes_read=396286 bytes_retransmit=0 bytes_invalid=0 send_seq=4254 receive_seq=4254 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998681 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.011 th0: temp=45.0 th1: temp=44.1 th2: temp=45.7 th3: temp=43.4 sysload=0.55 cputime=71.433 memavail=7407440 print_time=553.708 buffer_time=1.999 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 530.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6279508 bytes_read=781019 bytes_retransmit=9 bytes_invalid=0 send_seq=111026 receive_seq=111026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=15602 freq=400015557 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3874 bytes_read=13974 bytes_retransmit=0 bytes_invalid=0 send_seq=617 receive_seq=617 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999569 adj=49997501 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=31944 bytes_read=946682 bytes_retransmit=9 bytes_invalid=0 send_seq=4162 receive_seq=4162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000181 adj=63997702 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12966 bytes_read=73556 bytes_retransmit=9 bytes_invalid=0 send_seq=1360 receive_seq=1360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997572 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4033 bytes_read=130458 bytes_retransmit=9 bytes_invalid=0 send_seq=623 receive_seq=623 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4627 bytes_read=13722 bytes_retransmit=9 bytes_invalid=0 send_seq=618 receive_seq=618 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47703 bytes_read=396642 bytes_retransmit=0 bytes_invalid=0 send_seq=4255 receive_seq=4255 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999904 adj=31998694 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.011 th0: temp=45.1 th1: temp=44.2 th2: temp=45.2 th3: temp=43.4 sysload=0.55 cputime=71.568 memavail=7407440 print_time=554.785 buffer_time=2.075 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 531.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6292595 bytes_read=782424 bytes_retransmit=9 bytes_invalid=0 send_seq=111245 receive_seq=111245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=16049 freq=400015559 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3880 bytes_read=13990 bytes_retransmit=0 bytes_invalid=0 send_seq=618 receive_seq=618 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999566 adj=49997493 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32020 bytes_read=949796 bytes_retransmit=9 bytes_invalid=0 send_seq=4173 receive_seq=4173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997716 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12972 bytes_read=73656 bytes_retransmit=9 bytes_invalid=0 send_seq=1361 receive_seq=1361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997583 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4039 bytes_read=130692 bytes_retransmit=9 bytes_invalid=0 send_seq=624 receive_seq=624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4633 bytes_read=13738 bytes_retransmit=9 bytes_invalid=0 send_seq=619 receive_seq=619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47709 bytes_read=396998 bytes_retransmit=0 bytes_invalid=0 send_seq=4256 receive_seq=4256 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999903 adj=31998748 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.011 th0: temp=45.2 th1: temp=44.3 th2: temp=45.2 th3: temp=43.3 sysload=0.51 cputime=71.700 memavail=7407444 print_time=555.861 buffer_time=2.151 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 532.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6305047 bytes_read=783818 bytes_retransmit=9 bytes_invalid=0 send_seq=111456 receive_seq=111456 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=17010 freq=400015564 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3886 bytes_read=14006 bytes_retransmit=0 bytes_invalid=0 send_seq=619 receive_seq=619 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999565 adj=49997490 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32096 bytes_read=952912 bytes_retransmit=9 bytes_invalid=0 send_seq=4184 receive_seq=4184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000181 adj=63997697 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12978 bytes_read=73756 bytes_retransmit=9 bytes_invalid=0 send_seq=1362 receive_seq=1362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4045 bytes_read=130926 bytes_retransmit=9 bytes_invalid=0 send_seq=625 receive_seq=625 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4639 bytes_read=13765 bytes_retransmit=9 bytes_invalid=0 send_seq=620 receive_seq=620 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47715 bytes_read=397354 bytes_retransmit=0 bytes_invalid=0 send_seq=4257 receive_seq=4257 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999903 adj=31998717 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.011 th0: temp=45.4 th1: temp=44.2 th2: temp=45.2 th3: temp=43.4 sysload=0.51 cputime=71.831 memavail=7407444 print_time=556.938 buffer_time=2.227 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 533.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6317618 bytes_read=785178 bytes_retransmit=9 bytes_invalid=0 send_seq=111666 receive_seq=111666 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=17922 freq=400015565 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3892 bytes_read=14022 bytes_retransmit=0 bytes_invalid=0 send_seq=620 receive_seq=620 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999562 adj=49997496 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32172 bytes_read=956055 bytes_retransmit=9 bytes_invalid=0 send_seq=4195 receive_seq=4195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997697 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12984 bytes_read=73884 bytes_retransmit=9 bytes_invalid=0 send_seq=1363 receive_seq=1363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997541 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4051 bytes_read=131235 bytes_retransmit=9 bytes_invalid=0 send_seq=626 receive_seq=626 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4645 bytes_read=13781 bytes_retransmit=9 bytes_invalid=0 send_seq=621 receive_seq=621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47721 bytes_read=397710 bytes_retransmit=0 bytes_invalid=0 send_seq=4258 receive_seq=4258 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999902 adj=31998693 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.011 th0: temp=45.5 th1: temp=44.3 th2: temp=45.2 th3: temp=43.5 sysload=0.51 cputime=71.961 memavail=7407444 print_time=558.014 buffer_time=2.303 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 534.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6330151 bytes_read=786543 bytes_retransmit=9 bytes_invalid=0 send_seq=111877 receive_seq=111877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=18859 freq=400015555 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3898 bytes_read=14038 bytes_retransmit=0 bytes_invalid=0 send_seq=621 receive_seq=621 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999559 adj=49997491 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32248 bytes_read=959228 bytes_retransmit=9 bytes_invalid=0 send_seq=4206 receive_seq=4206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000179 adj=63997682 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12990 bytes_read=73984 bytes_retransmit=9 bytes_invalid=0 send_seq=1364 receive_seq=1364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997529 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4057 bytes_read=131469 bytes_retransmit=9 bytes_invalid=0 send_seq=627 receive_seq=627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997693 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4651 bytes_read=13797 bytes_retransmit=9 bytes_invalid=0 send_seq=622 receive_seq=622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47727 bytes_read=398066 bytes_retransmit=0 bytes_invalid=0 send_seq=4259 receive_seq=4259 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998678 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.011 th0: temp=45.2 th1: temp=44.1 th2: temp=45.6 th3: temp=43.6 sysload=0.51 cputime=72.093 memavail=7407444 print_time=559.091 buffer_time=2.380 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 535.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6342657 bytes_read=787933 bytes_retransmit=9 bytes_invalid=0 send_seq=112084 receive_seq=112084 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=19787 freq=400015558 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3904 bytes_read=14067 bytes_retransmit=0 bytes_invalid=0 send_seq=622 receive_seq=622 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999555 adj=49997493 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32324 bytes_read=962359 bytes_retransmit=9 bytes_invalid=0 send_seq=4217 receive_seq=4217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997690 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=12996 bytes_read=74098 bytes_retransmit=9 bytes_invalid=0 send_seq=1365 receive_seq=1365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997542 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4063 bytes_read=131703 bytes_retransmit=9 bytes_invalid=0 send_seq=628 receive_seq=628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997690 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4657 bytes_read=13813 bytes_retransmit=9 bytes_invalid=0 send_seq=623 receive_seq=623 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47733 bytes_read=398422 bytes_retransmit=0 bytes_invalid=0 send_seq=4260 receive_seq=4260 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998671 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.011 th0: temp=45.2 th1: temp=44.5 th2: temp=44.7 th3: temp=43.3 sysload=0.51 cputime=72.223 memavail=7407216 print_time=560.167 buffer_time=2.455 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 536.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6355319 bytes_read=789313 bytes_retransmit=9 bytes_invalid=0 send_seq=112299 receive_seq=112299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=20599 freq=400015541 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3910 bytes_read=14083 bytes_retransmit=0 bytes_invalid=0 send_seq=623 receive_seq=623 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999553 adj=49997477 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32400 bytes_read=965503 bytes_retransmit=9 bytes_invalid=0 send_seq=4228 receive_seq=4228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997677 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13002 bytes_read=74226 bytes_retransmit=9 bytes_invalid=0 send_seq=1366 receive_seq=1366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997537 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4069 bytes_read=131997 bytes_retransmit=9 bytes_invalid=0 send_seq=629 receive_seq=629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4663 bytes_read=13829 bytes_retransmit=9 bytes_invalid=0 send_seq=624 receive_seq=624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47739 bytes_read=398796 bytes_retransmit=0 bytes_invalid=0 send_seq=4261 receive_seq=4261 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998663 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.011 th0: temp=45.0 th1: temp=44.1 th2: temp=45.3 th3: temp=43.6 sysload=0.47 cputime=72.356 memavail=7407216 print_time=561.243 buffer_time=2.523 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 537.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6367795 bytes_read=790677 bytes_retransmit=9 bytes_invalid=0 send_seq=112510 receive_seq=112510 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=15419 freq=400015542 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3916 bytes_read=14099 bytes_retransmit=0 bytes_invalid=0 send_seq=624 receive_seq=624 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999551 adj=49997503 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32476 bytes_read=968619 bytes_retransmit=9 bytes_invalid=0 send_seq=4239 receive_seq=4239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997703 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13008 bytes_read=74326 bytes_retransmit=9 bytes_invalid=0 send_seq=1367 receive_seq=1367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997559 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4075 bytes_read=132231 bytes_retransmit=9 bytes_invalid=0 send_seq=630 receive_seq=630 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997701 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4669 bytes_read=13856 bytes_retransmit=9 bytes_invalid=0 send_seq=625 receive_seq=625 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47745 bytes_read=399152 bytes_retransmit=0 bytes_invalid=0 send_seq=4262 receive_seq=4262 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998672 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.011 th0: temp=45.4 th1: temp=44.3 th2: temp=45.4 th3: temp=43.4 sysload=0.47 cputime=72.479 memavail=7407216 print_time=561.782 buffer_time=2.061 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 538.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6380699 bytes_read=792101 bytes_retransmit=9 bytes_invalid=0 send_seq=112727 receive_seq=112727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=16049 freq=400015544 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3922 bytes_read=14115 bytes_retransmit=0 bytes_invalid=0 send_seq=625 receive_seq=625 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999551 adj=49997475 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32552 bytes_read=971793 bytes_retransmit=9 bytes_invalid=0 send_seq=4250 receive_seq=4250 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997811 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13014 bytes_read=74426 bytes_retransmit=9 bytes_invalid=0 send_seq=1368 receive_seq=1368 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997562 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4081 bytes_read=132480 bytes_retransmit=9 bytes_invalid=0 send_seq=631 receive_seq=631 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997696 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4675 bytes_read=13872 bytes_retransmit=9 bytes_invalid=0 send_seq=626 receive_seq=626 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47751 bytes_read=399508 bytes_retransmit=0 bytes_invalid=0 send_seq=4263 receive_seq=4263 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998660 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.011 th0: temp=45.4 th1: temp=44.3 th2: temp=45.3 th3: temp=43.6 sysload=0.47 cputime=72.614 memavail=7407216 print_time=562.858 buffer_time=2.137 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 539.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6393399 bytes_read=793491 bytes_retransmit=9 bytes_invalid=0 send_seq=112943 receive_seq=112943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=16811 freq=400015554 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3928 bytes_read=14131 bytes_retransmit=0 bytes_invalid=0 send_seq=626 receive_seq=626 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999549 adj=49997493 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32628 bytes_read=974936 bytes_retransmit=9 bytes_invalid=0 send_seq=4261 receive_seq=4261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997798 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13020 bytes_read=74554 bytes_retransmit=9 bytes_invalid=0 send_seq=1369 receive_seq=1369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997556 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4087 bytes_read=132774 bytes_retransmit=9 bytes_invalid=0 send_seq=632 receive_seq=632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4681 bytes_read=13888 bytes_retransmit=9 bytes_invalid=0 send_seq=627 receive_seq=627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47757 bytes_read=399864 bytes_retransmit=0 bytes_invalid=0 send_seq=4264 receive_seq=4264 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999899 adj=31998659 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=45.4 th1: temp=44.4 th2: temp=45.3 th3: temp=43.6 sysload=0.47 cputime=72.749 memavail=7407216 print_time=563.935 buffer_time=2.213 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 540.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6405883 bytes_read=794872 bytes_retransmit=9 bytes_invalid=0 send_seq=113154 receive_seq=113154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=17756 freq=400015553 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3934 bytes_read=14160 bytes_retransmit=0 bytes_invalid=0 send_seq=627 receive_seq=627 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999546 adj=49997471 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32704 bytes_read=978067 bytes_retransmit=9 bytes_invalid=0 send_seq=4272 receive_seq=4272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997758 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13026 bytes_read=74668 bytes_retransmit=9 bytes_invalid=0 send_seq=1370 receive_seq=1370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997567 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4093 bytes_read=133008 bytes_retransmit=9 bytes_invalid=0 send_seq=633 receive_seq=633 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4687 bytes_read=13904 bytes_retransmit=9 bytes_invalid=0 send_seq=628 receive_seq=628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47763 bytes_read=400220 bytes_retransmit=0 bytes_invalid=0 send_seq=4265 receive_seq=4265 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999899 adj=31998645 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=45.4 th1: temp=44.4 th2: temp=45.2 th3: temp=43.5 sysload=0.47 cputime=72.880 memavail=7407216 print_time=565.011 buffer_time=2.289 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 541.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6418412 bytes_read=796261 bytes_retransmit=9 bytes_invalid=0 send_seq=113364 receive_seq=113364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=18661 freq=400015550 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3940 bytes_read=14176 bytes_retransmit=0 bytes_invalid=0 send_seq=628 receive_seq=628 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999543 adj=49997471 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32773 bytes_read=981156 bytes_retransmit=9 bytes_invalid=0 send_seq=4282 receive_seq=4282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997741 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13032 bytes_read=74768 bytes_retransmit=9 bytes_invalid=0 send_seq=1371 receive_seq=1371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4099 bytes_read=133242 bytes_retransmit=9 bytes_invalid=0 send_seq=634 receive_seq=634 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999522 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4693 bytes_read=13920 bytes_retransmit=9 bytes_invalid=0 send_seq=629 receive_seq=629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47769 bytes_read=400576 bytes_retransmit=0 bytes_invalid=0 send_seq=4266 receive_seq=4266 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999898 adj=31998639 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=45.3 th1: temp=44.4 th2: temp=45.2 th3: temp=43.6 sysload=0.43 cputime=73.010 memavail=7407216 print_time=566.088 buffer_time=2.365 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 542.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6430986 bytes_read=797652 bytes_retransmit=9 bytes_invalid=0 send_seq=113578 receive_seq=113578 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=19589 freq=400015558 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3952 bytes_read=14208 bytes_retransmit=0 bytes_invalid=0 send_seq=630 receive_seq=630 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999540 adj=49997473 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32855 bytes_read=984318 bytes_retransmit=9 bytes_invalid=0 send_seq=4294 receive_seq=4294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997894 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13044 bytes_read=74912 bytes_retransmit=9 bytes_invalid=0 send_seq=1373 receive_seq=1373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000008 adj=63997582 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4111 bytes_read=133552 bytes_retransmit=9 bytes_invalid=0 send_seq=636 receive_seq=636 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997683 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4705 bytes_read=13963 bytes_retransmit=9 bytes_invalid=0 send_seq=631 receive_seq=631 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47781 bytes_read=400948 bytes_retransmit=0 bytes_invalid=0 send_seq=4268 receive_seq=4268 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999898 adj=31998640 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=45.5 th1: temp=44.2 th2: temp=45.3 th3: temp=43.7 sysload=0.43 cputime=73.146 memavail=7407236 print_time=567.164 buffer_time=2.441 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 543.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6443506 bytes_read=799027 bytes_retransmit=9 bytes_invalid=0 send_seq=113791 receive_seq=113791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=20533 freq=400015606 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3958 bytes_read=14224 bytes_retransmit=0 bytes_invalid=0 send_seq=631 receive_seq=631 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999538 adj=49997450 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32931 bytes_read=987431 bytes_retransmit=9 bytes_invalid=0 send_seq=4305 receive_seq=4305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997956 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13050 bytes_read=75012 bytes_retransmit=9 bytes_invalid=0 send_seq=1374 receive_seq=1374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997543 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4117 bytes_read=133801 bytes_retransmit=9 bytes_invalid=0 send_seq=637 receive_seq=637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4711 bytes_read=13979 bytes_retransmit=9 bytes_invalid=0 send_seq=632 receive_seq=632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47787 bytes_read=401304 bytes_retransmit=0 bytes_invalid=0 send_seq=4269 receive_seq=4269 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999897 adj=31998630 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=45.4 th1: temp=44.2 th2: temp=45.3 th3: temp=43.5 sysload=0.43 cputime=73.274 memavail=7407236 print_time=568.241 buffer_time=2.517 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 544.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6456031 bytes_read=800436 bytes_retransmit=9 bytes_invalid=0 send_seq=114005 receive_seq=114005 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=15353 freq=400015591 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=3964 bytes_read=14240 bytes_retransmit=0 bytes_invalid=0 send_seq=632 receive_seq=632 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999536 adj=49997395 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33007 bytes_read=990544 bytes_retransmit=9 bytes_invalid=0 send_seq=4316 receive_seq=4316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997805 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13056 bytes_read=75112 bytes_retransmit=9 bytes_invalid=0 send_seq=1375 receive_seq=1375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997448 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4123 bytes_read=134035 bytes_retransmit=9 bytes_invalid=0 send_seq=638 receive_seq=638 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997601 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4717 bytes_read=13995 bytes_retransmit=9 bytes_invalid=0 send_seq=633 receive_seq=633 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47793 bytes_read=401660 bytes_retransmit=0 bytes_invalid=0 send_seq=4270 receive_seq=4270 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999898 adj=31998585 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=45.4 th1: temp=44.3 th2: temp=45.4 th3: temp=43.6 sysload=0.43 cputime=73.402 memavail=7402700 print_time=568.779 buffer_time=2.055 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 545.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6468856 bytes_read=801852 bytes_retransmit=9 bytes_invalid=0 send_seq=114223 receive_seq=114223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=16049 freq=400015577 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3970 bytes_read=14269 bytes_retransmit=0 bytes_invalid=0 send_seq=633 receive_seq=633 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999536 adj=49997400 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33083 bytes_read=993704 bytes_retransmit=9 bytes_invalid=0 send_seq=4327 receive_seq=4327 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997802 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13062 bytes_read=75254 bytes_retransmit=9 bytes_invalid=0 send_seq=1376 receive_seq=1376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997471 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4129 bytes_read=134329 bytes_retransmit=9 bytes_invalid=0 send_seq=639 receive_seq=639 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997616 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4723 bytes_read=14011 bytes_retransmit=9 bytes_invalid=0 send_seq=634 receive_seq=634 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47799 bytes_read=402016 bytes_retransmit=0 bytes_invalid=0 send_seq=4271 receive_seq=4271 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999897 adj=31998610 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.011 th0: temp=45.5 th1: temp=44.5 th2: temp=45.4 th3: temp=43.4 sysload=0.43 cputime=73.541 memavail=7407404 print_time=569.855 buffer_time=2.132 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 546.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6481615 bytes_read=803237 bytes_retransmit=9 bytes_invalid=0 send_seq=114439 receive_seq=114438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=16762 freq=400015575 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3976 bytes_read=14285 bytes_retransmit=0 bytes_invalid=0 send_seq=634 receive_seq=634 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999533 adj=49997434 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33159 bytes_read=996876 bytes_retransmit=9 bytes_invalid=0 send_seq=4338 receive_seq=4338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997824 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13068 bytes_read=75354 bytes_retransmit=9 bytes_invalid=0 send_seq=1377 receive_seq=1377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4135 bytes_read=134563 bytes_retransmit=9 bytes_invalid=0 send_seq=640 receive_seq=640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4729 bytes_read=14027 bytes_retransmit=9 bytes_invalid=0 send_seq=635 receive_seq=635 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47805 bytes_read=402372 bytes_retransmit=0 bytes_invalid=0 send_seq=4272 receive_seq=4272 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999899 adj=31998621 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.011 th0: temp=45.2 th1: temp=44.4 th2: temp=45.3 th3: temp=43.7 sysload=0.47 cputime=73.673 memavail=7407404 print_time=570.932 buffer_time=2.208 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 547.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6494169 bytes_read=804622 bytes_retransmit=9 bytes_invalid=0 send_seq=114649 receive_seq=114648 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=17673 freq=400015574 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3982 bytes_read=14301 bytes_retransmit=0 bytes_invalid=0 send_seq=635 receive_seq=635 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999530 adj=49997441 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33235 bytes_read=999989 bytes_retransmit=9 bytes_invalid=0 send_seq=4349 receive_seq=4349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997772 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13074 bytes_read=75454 bytes_retransmit=9 bytes_invalid=0 send_seq=1378 receive_seq=1378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4141 bytes_read=134797 bytes_retransmit=9 bytes_invalid=0 send_seq=641 receive_seq=641 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997634 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4735 bytes_read=14054 bytes_retransmit=9 bytes_invalid=0 send_seq=636 receive_seq=636 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47811 bytes_read=402728 bytes_retransmit=0 bytes_invalid=0 send_seq=4273 receive_seq=4273 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999898 adj=31998654 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=45.4 th1: temp=44.4 th2: temp=45.4 th3: temp=43.6 sysload=0.47 cputime=73.805 memavail=7407412 print_time=572.008 buffer_time=2.284 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 548.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6506676 bytes_read=805992 bytes_retransmit=9 bytes_invalid=0 send_seq=114860 receive_seq=114860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=18578 freq=400015606 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3988 bytes_read=14317 bytes_retransmit=0 bytes_invalid=0 send_seq=636 receive_seq=636 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999528 adj=49997442 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33311 bytes_read=1003130 bytes_retransmit=9 bytes_invalid=0 send_seq=4360 receive_seq=4360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997829 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13080 bytes_read=75582 bytes_retransmit=9 bytes_invalid=0 send_seq=1379 receive_seq=1379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4147 bytes_read=135106 bytes_retransmit=9 bytes_invalid=0 send_seq=642 receive_seq=642 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4741 bytes_read=14070 bytes_retransmit=9 bytes_invalid=0 send_seq=637 receive_seq=637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47817 bytes_read=403084 bytes_retransmit=0 bytes_invalid=0 send_seq=4274 receive_seq=4274 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999898 adj=31998647 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=45.5 th1: temp=44.4 th2: temp=45.3 th3: temp=43.6 sysload=0.47 cputime=73.940 memavail=7409932 print_time=573.085 buffer_time=2.359 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 549.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6519190 bytes_read=807352 bytes_retransmit=9 bytes_invalid=0 send_seq=115070 receive_seq=115070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=19506 freq=400015643 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=3994 bytes_read=14333 bytes_retransmit=0 bytes_invalid=0 send_seq=637 receive_seq=637 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999525 adj=49997401 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33387 bytes_read=1006244 bytes_retransmit=9 bytes_invalid=0 send_seq=4371 receive_seq=4371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997820 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13086 bytes_read=75682 bytes_retransmit=9 bytes_invalid=0 send_seq=1380 receive_seq=1380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997440 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4153 bytes_read=135340 bytes_retransmit=9 bytes_invalid=0 send_seq=643 receive_seq=643 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997595 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4747 bytes_read=14086 bytes_retransmit=9 bytes_invalid=0 send_seq=638 receive_seq=638 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=24.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47823 bytes_read=403440 bytes_retransmit=0 bytes_invalid=0 send_seq=4275 receive_seq=4275 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999898 adj=31998617 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=45.3 th1: temp=44.4 th2: temp=45.4 th3: temp=43.7 sysload=0.47 cputime=74.076 memavail=7409456 print_time=574.161 buffer_time=2.435 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 550.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6531699 bytes_read=808762 bytes_retransmit=9 bytes_invalid=0 send_seq=115281 receive_seq=115281 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=20450 freq=400015634 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4000 bytes_read=14362 bytes_retransmit=0 bytes_invalid=0 send_seq=638 receive_seq=638 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999522 adj=49997357 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33463 bytes_read=1009377 bytes_retransmit=9 bytes_invalid=0 send_seq=4382 receive_seq=4382 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997700 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13092 bytes_read=75796 bytes_retransmit=9 bytes_invalid=0 send_seq=1381 receive_seq=1381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000014 adj=63997396 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4159 bytes_read=135574 bytes_retransmit=9 bytes_invalid=0 send_seq=644 receive_seq=644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997552 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4753 bytes_read=14102 bytes_retransmit=9 bytes_invalid=0 send_seq=639 receive_seq=639 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999419 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47829 bytes_read=403796 bytes_retransmit=0 bytes_invalid=0 send_seq=4276 receive_seq=4276 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999898 adj=31998584 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=45.4 th1: temp=44.5 th2: temp=45.5 th3: temp=43.7 sysload=0.47 cputime=74.210 memavail=7409456 print_time=575.238 buffer_time=2.512 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 551.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6544230 bytes_read=810132 bytes_retransmit=9 bytes_invalid=0 send_seq=115493 receive_seq=115493 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=15287 freq=400015627 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4006 bytes_read=14378 bytes_retransmit=0 bytes_invalid=0 send_seq=639 receive_seq=639 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999518 adj=49997379 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33539 bytes_read=1012518 bytes_retransmit=9 bytes_invalid=0 send_seq=4393 receive_seq=4393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997696 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13098 bytes_read=75924 bytes_retransmit=9 bytes_invalid=0 send_seq=1382 receive_seq=1382 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000014 adj=63997527 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4165 bytes_read=135868 bytes_retransmit=9 bytes_invalid=0 send_seq=645 receive_seq=645 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997583 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4759 bytes_read=14118 bytes_retransmit=9 bytes_invalid=0 send_seq=640 receive_seq=640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47835 bytes_read=404152 bytes_retransmit=0 bytes_invalid=0 send_seq=4277 receive_seq=4277 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999897 adj=31998606 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=45.6 th1: temp=44.4 th2: temp=45.6 th3: temp=43.6 sysload=0.44 cputime=74.331 memavail=7409456 print_time=575.776 buffer_time=2.050 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 552.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6556950 bytes_read=811517 bytes_retransmit=9 bytes_invalid=0 send_seq=115708 receive_seq=115708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=16049 freq=400015617 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4012 bytes_read=14394 bytes_retransmit=0 bytes_invalid=0 send_seq=640 receive_seq=640 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999512 adj=49997340 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33608 bytes_read=1015607 bytes_retransmit=9 bytes_invalid=0 send_seq=4403 receive_seq=4403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997673 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13104 bytes_read=76024 bytes_retransmit=9 bytes_invalid=0 send_seq=1383 receive_seq=1383 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000013 adj=63997536 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4171 bytes_read=136102 bytes_retransmit=9 bytes_invalid=0 send_seq=646 receive_seq=646 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997588 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4765 bytes_read=14145 bytes_retransmit=9 bytes_invalid=0 send_seq=641 receive_seq=641 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47841 bytes_read=404508 bytes_retransmit=0 bytes_invalid=0 send_seq=4278 receive_seq=4278 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999897 adj=31998605 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=45.4 th1: temp=44.5 th2: temp=45.3 th3: temp=43.7 sysload=0.44 cputime=74.462 memavail=7409456 print_time=576.852 buffer_time=2.126 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 553.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6569753 bytes_read=812931 bytes_retransmit=9 bytes_invalid=0 send_seq=115923 receive_seq=115923 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=16695 freq=400015705 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4018 bytes_read=14410 bytes_retransmit=0 bytes_invalid=0 send_seq=641 receive_seq=641 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999505 adj=49997315 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33684 bytes_read=1018723 bytes_retransmit=9 bytes_invalid=0 send_seq=4414 receive_seq=4414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63998045 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13110 bytes_read=76124 bytes_retransmit=9 bytes_invalid=0 send_seq=1384 receive_seq=1384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000012 adj=63997541 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4177 bytes_read=136351 bytes_retransmit=9 bytes_invalid=0 send_seq=647 receive_seq=647 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4771 bytes_read=14161 bytes_retransmit=9 bytes_invalid=0 send_seq=642 receive_seq=642 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47847 bytes_read=404864 bytes_retransmit=0 bytes_invalid=0 send_seq=4279 receive_seq=4279 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999898 adj=31998618 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=45.6 th1: temp=44.6 th2: temp=45.7 th3: temp=43.9 sysload=0.44 cputime=74.594 memavail=7409472 print_time=577.929 buffer_time=2.202 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 554.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6582341 bytes_read=814301 bytes_retransmit=9 bytes_invalid=0 send_seq=116135 receive_seq=116135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=17607 freq=400015681 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4024 bytes_read=14426 bytes_retransmit=0 bytes_invalid=0 send_seq=642 receive_seq=642 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999497 adj=49997161 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33760 bytes_read=1021925 bytes_retransmit=9 bytes_invalid=0 send_seq=4425 receive_seq=4425 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997796 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13116 bytes_read=76252 bytes_retransmit=9 bytes_invalid=0 send_seq=1385 receive_seq=1385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000012 adj=63997357 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4183 bytes_read=136645 bytes_retransmit=9 bytes_invalid=0 send_seq=648 receive_seq=648 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997496 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4777 bytes_read=14177 bytes_retransmit=9 bytes_invalid=0 send_seq=643 receive_seq=643 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999404 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47853 bytes_read=405220 bytes_retransmit=0 bytes_invalid=0 send_seq=4280 receive_seq=4280 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999897 adj=31998551 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.011 th0: temp=46.0 th1: temp=44.5 th2: temp=45.2 th3: temp=43.8 sysload=0.44 cputime=74.728 memavail=7409928 print_time=579.005 buffer_time=2.278 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 555.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6594845 bytes_read=815677 bytes_retransmit=9 bytes_invalid=0 send_seq=116345 receive_seq=116345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=18528 freq=400015669 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=4030 bytes_read=14455 bytes_retransmit=0 bytes_invalid=0 send_seq=643 receive_seq=643 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999489 adj=49997188 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33836 bytes_read=1025059 bytes_retransmit=9 bytes_invalid=0 send_seq=4436 receive_seq=4436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997788 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13122 bytes_read=76366 bytes_retransmit=9 bytes_invalid=0 send_seq=1386 receive_seq=1386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000016 adj=63997428 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4189 bytes_read=136879 bytes_retransmit=9 bytes_invalid=0 send_seq=649 receive_seq=649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997565 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4783 bytes_read=14193 bytes_retransmit=9 bytes_invalid=0 send_seq=644 receive_seq=644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999420 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47859 bytes_read=405576 bytes_retransmit=0 bytes_invalid=0 send_seq=4281 receive_seq=4281 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999897 adj=31998584 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.011 th0: temp=45.4 th1: temp=44.6 th2: temp=45.0 th3: temp=43.9 sysload=0.44 cputime=74.866 memavail=7409456 print_time=580.082 buffer_time=2.353 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 556.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6607376 bytes_read=817076 bytes_retransmit=9 bytes_invalid=0 send_seq=116557 receive_seq=116557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=19456 freq=400015768 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=4036 bytes_read=14471 bytes_retransmit=0 bytes_invalid=0 send_seq=644 receive_seq=644 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999480 adj=49997189 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33912 bytes_read=1028174 bytes_retransmit=9 bytes_invalid=0 send_seq=4447 receive_seq=4447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997750 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13128 bytes_read=76466 bytes_retransmit=9 bytes_invalid=0 send_seq=1387 receive_seq=1387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000015 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4195 bytes_read=137113 bytes_retransmit=9 bytes_invalid=0 send_seq=650 receive_seq=650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997593 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4789 bytes_read=14209 bytes_retransmit=9 bytes_invalid=0 send_seq=645 receive_seq=645 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47865 bytes_read=405932 bytes_retransmit=0 bytes_invalid=0 send_seq=4282 receive_seq=4282 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998608 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=45.5 th1: temp=44.4 th2: temp=45.3 th3: temp=43.7 sysload=0.40 cputime=74.998 memavail=7409456 print_time=581.158 buffer_time=2.430 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 557.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6619901 bytes_read=818429 bytes_retransmit=9 bytes_invalid=0 send_seq=116766 receive_seq=116766 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=20384 freq=400015753 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=4042 bytes_read=14487 bytes_retransmit=0 bytes_invalid=0 send_seq=645 receive_seq=645 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999469 adj=49997024 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33988 bytes_read=1031317 bytes_retransmit=9 bytes_invalid=0 send_seq=4458 receive_seq=4458 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997519 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13134 bytes_read=76594 bytes_retransmit=9 bytes_invalid=0 send_seq=1388 receive_seq=1388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000014 adj=63997326 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4201 bytes_read=137407 bytes_retransmit=9 bytes_invalid=0 send_seq=651 receive_seq=651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997467 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4795 bytes_read=14236 bytes_retransmit=9 bytes_invalid=0 send_seq=646 receive_seq=646 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999404 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47871 bytes_read=406288 bytes_retransmit=0 bytes_invalid=0 send_seq=4283 receive_seq=4283 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999897 adj=31998520 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=45.4 th1: temp=44.5 th2: temp=45.4 th3: temp=43.8 sysload=0.40 cputime=75.127 memavail=7409456 print_time=582.235 buffer_time=2.506 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 558.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6632449 bytes_read=819797 bytes_retransmit=9 bytes_invalid=0 send_seq=116978 receive_seq=116978 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=15204 freq=400015769 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=4048 bytes_read=14503 bytes_retransmit=0 bytes_invalid=0 send_seq=646 receive_seq=646 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999456 adj=49997025 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34064 bytes_read=1034432 bytes_retransmit=9 bytes_invalid=0 send_seq=4469 receive_seq=4469 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997586 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13140 bytes_read=76694 bytes_retransmit=9 bytes_invalid=0 send_seq=1389 receive_seq=1389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000014 adj=63997382 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4207 bytes_read=137656 bytes_retransmit=9 bytes_invalid=0 send_seq=652 receive_seq=652 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997538 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4801 bytes_read=14252 bytes_retransmit=9 bytes_invalid=0 send_seq=647 receive_seq=647 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999414 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47877 bytes_read=406628 bytes_retransmit=0 bytes_invalid=0 send_seq=4284 receive_seq=4284 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998558 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=45.3 th1: temp=44.4 th2: temp=45.5 th3: temp=43.5 sysload=0.40 cputime=75.245 memavail=7409456 print_time=582.773 buffer_time=2.044 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 559.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6645075 bytes_read=821201 bytes_retransmit=9 bytes_invalid=0 send_seq=117191 receive_seq=117191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=16049 freq=400015764 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=4054 bytes_read=14519 bytes_retransmit=0 bytes_invalid=0 send_seq=647 receive_seq=647 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999444 adj=49996863 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34140 bytes_read=1037548 bytes_retransmit=9 bytes_invalid=0 send_seq=4480 receive_seq=4480 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997522 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13146 bytes_read=76794 bytes_retransmit=9 bytes_invalid=0 send_seq=1390 receive_seq=1390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000014 adj=63997353 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4213 bytes_read=137890 bytes_retransmit=9 bytes_invalid=0 send_seq=653 receive_seq=653 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997508 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4807 bytes_read=14268 bytes_retransmit=9 bytes_invalid=0 send_seq=648 receive_seq=648 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999408 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47883 bytes_read=406984 bytes_retransmit=0 bytes_invalid=0 send_seq=4285 receive_seq=4285 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998540 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=45.6 th1: temp=44.5 th2: temp=45.5 th3: temp=43.6 sysload=0.40 cputime=75.377 memavail=7409456 print_time=583.849 buffer_time=2.120 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 560.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6657975 bytes_read=822617 bytes_retransmit=9 bytes_invalid=0 send_seq=117409 receive_seq=117409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=16613 freq=400015743 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=4060 bytes_read=14535 bytes_retransmit=0 bytes_invalid=0 send_seq=648 receive_seq=648 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999431 adj=49996794 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34216 bytes_read=1040706 bytes_retransmit=9 bytes_invalid=0 send_seq=4491 receive_seq=4491 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997506 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13152 bytes_read=76936 bytes_retransmit=9 bytes_invalid=0 send_seq=1391 receive_seq=1391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000014 adj=63997374 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4219 bytes_read=138184 bytes_retransmit=9 bytes_invalid=0 send_seq=654 receive_seq=654 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997532 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4813 bytes_read=14284 bytes_retransmit=9 bytes_invalid=0 send_seq=649 receive_seq=649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999412 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47889 bytes_read=407340 bytes_retransmit=0 bytes_invalid=0 send_seq=4286 receive_seq=4286 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999895 adj=31998549 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=45.4 th1: temp=44.6 th2: temp=45.6 th3: temp=44.0 sysload=0.40 cputime=75.512 memavail=7409480 print_time=584.926 buffer_time=2.196 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 561.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6670487 bytes_read=823992 bytes_retransmit=9 bytes_invalid=0 send_seq=117622 receive_seq=117622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=17541 freq=400015740 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4066 bytes_read=14564 bytes_retransmit=0 bytes_invalid=0 send_seq=649 receive_seq=649 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999418 adj=49996827 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34292 bytes_read=1043821 bytes_retransmit=9 bytes_invalid=0 send_seq=4502 receive_seq=4502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997560 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13158 bytes_read=77036 bytes_retransmit=9 bytes_invalid=0 send_seq=1392 receive_seq=1392 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000017 adj=63997440 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4225 bytes_read=138418 bytes_retransmit=9 bytes_invalid=0 send_seq=655 receive_seq=655 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997585 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4819 bytes_read=14300 bytes_retransmit=9 bytes_invalid=0 send_seq=650 receive_seq=650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47895 bytes_read=407696 bytes_retransmit=0 bytes_invalid=0 send_seq=4287 receive_seq=4287 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999895 adj=31998582 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=45.7 th1: temp=44.4 th2: temp=45.3 th3: temp=43.6 sysload=0.45 cputime=75.642 memavail=7408724 print_time=586.002 buffer_time=2.272 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 562.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6683032 bytes_read=825391 bytes_retransmit=9 bytes_invalid=0 send_seq=117834 receive_seq=117834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=18462 freq=400015720 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4072 bytes_read=14580 bytes_retransmit=0 bytes_invalid=0 send_seq=650 receive_seq=650 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999404 adj=49996819 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34368 bytes_read=1046994 bytes_retransmit=9 bytes_invalid=0 send_seq=4513 receive_seq=4513 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997565 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13164 bytes_read=77136 bytes_retransmit=9 bytes_invalid=0 send_seq=1393 receive_seq=1393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000015 adj=63997493 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4231 bytes_read=138652 bytes_retransmit=9 bytes_invalid=0 send_seq=656 receive_seq=656 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997596 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4825 bytes_read=14327 bytes_retransmit=9 bytes_invalid=0 send_seq=651 receive_seq=651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47901 bytes_read=408052 bytes_retransmit=0 bytes_invalid=0 send_seq=4288 receive_seq=4288 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999895 adj=31998597 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=45.5 th1: temp=44.6 th2: temp=45.5 th3: temp=43.8 sysload=0.45 cputime=75.784 memavail=7408844 print_time=587.079 buffer_time=2.347 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 563.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6695627 bytes_read=826761 bytes_retransmit=9 bytes_invalid=0 send_seq=118047 receive_seq=118046 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=19373 freq=400015736 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4078 bytes_read=14596 bytes_retransmit=0 bytes_invalid=0 send_seq=651 receive_seq=651 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999389 adj=49996824 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34444 bytes_read=1050136 bytes_retransmit=9 bytes_invalid=0 send_seq=4524 receive_seq=4524 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997609 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13170 bytes_read=77264 bytes_retransmit=9 bytes_invalid=0 send_seq=1394 receive_seq=1394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997514 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4237 bytes_read=138961 bytes_retransmit=9 bytes_invalid=0 send_seq=657 receive_seq=657 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4831 bytes_read=14343 bytes_retransmit=9 bytes_invalid=0 send_seq=652 receive_seq=652 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47907 bytes_read=408408 bytes_retransmit=0 bytes_invalid=0 send_seq=4289 receive_seq=4289 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998619 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=45.5 th1: temp=44.7 th2: temp=45.6 th3: temp=43.9 sysload=0.45 cputime=75.920 memavail=7408844 print_time=588.155 buffer_time=2.423 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 564.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6708144 bytes_read=828131 bytes_retransmit=9 bytes_invalid=0 send_seq=118258 receive_seq=118258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=20285 freq=400015732 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4084 bytes_read=14612 bytes_retransmit=0 bytes_invalid=0 send_seq=652 receive_seq=652 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999374 adj=49996763 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34513 bytes_read=1053225 bytes_retransmit=9 bytes_invalid=0 send_seq=4534 receive_seq=4534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997575 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13176 bytes_read=77364 bytes_retransmit=9 bytes_invalid=0 send_seq=1395 receive_seq=1395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4243 bytes_read=139195 bytes_retransmit=9 bytes_invalid=0 send_seq=658 receive_seq=658 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997604 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4837 bytes_read=14359 bytes_retransmit=9 bytes_invalid=0 send_seq=653 receive_seq=653 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47913 bytes_read=408764 bytes_retransmit=0 bytes_invalid=0 send_seq=4290 receive_seq=4290 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999895 adj=31998606 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=45.8 th1: temp=44.7 th2: temp=45.4 th3: temp=43.9 sysload=0.45 cputime=76.052 memavail=7408620 print_time=589.232 buffer_time=2.498 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 565.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6720715 bytes_read=829546 bytes_retransmit=9 bytes_invalid=0 send_seq=118471 receive_seq=118470 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=15088 freq=400015714 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4090 bytes_read=14641 bytes_retransmit=0 bytes_invalid=0 send_seq=653 receive_seq=653 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999359 adj=49996743 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34589 bytes_read=1056355 bytes_retransmit=9 bytes_invalid=0 send_seq=4545 receive_seq=4545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997580 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13182 bytes_read=77478 bytes_retransmit=9 bytes_invalid=0 send_seq=1396 receive_seq=1396 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997527 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4249 bytes_read=139429 bytes_retransmit=9 bytes_invalid=0 send_seq=659 receive_seq=659 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4843 bytes_read=14375 bytes_retransmit=9 bytes_invalid=0 send_seq=654 receive_seq=654 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47919 bytes_read=409120 bytes_retransmit=0 bytes_invalid=0 send_seq=4291 receive_seq=4291 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999895 adj=31998619 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=45.5 th1: temp=44.7 th2: temp=45.7 th3: temp=43.9 sysload=0.45 cputime=76.166 memavail=7407152 print_time=589.770 buffer_time=2.035 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 566.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6733180 bytes_read=830906 bytes_retransmit=9 bytes_invalid=0 send_seq=118680 receive_seq=118680 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=16049 freq=400015706 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4096 bytes_read=14657 bytes_retransmit=0 bytes_invalid=0 send_seq=654 receive_seq=654 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999343 adj=49996598 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34665 bytes_read=1059496 bytes_retransmit=9 bytes_invalid=0 send_seq=4556 receive_seq=4556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997578 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13188 bytes_read=77606 bytes_retransmit=9 bytes_invalid=0 send_seq=1397 receive_seq=1397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997603 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4255 bytes_read=139723 bytes_retransmit=9 bytes_invalid=0 send_seq=660 receive_seq=660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4849 bytes_read=14391 bytes_retransmit=9 bytes_invalid=0 send_seq=655 receive_seq=655 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47925 bytes_read=409476 bytes_retransmit=0 bytes_invalid=0 send_seq=4292 receive_seq=4292 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999895 adj=31998639 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=45.6 th1: temp=44.5 th2: temp=45.6 th3: temp=43.7 sysload=0.41 cputime=76.298 memavail=7407156 print_time=590.846 buffer_time=2.111 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 567.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6746210 bytes_read=832311 bytes_retransmit=9 bytes_invalid=0 send_seq=118899 receive_seq=118899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=16497 freq=400015701 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4102 bytes_read=14673 bytes_retransmit=0 bytes_invalid=0 send_seq=655 receive_seq=655 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999327 adj=49996501 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34741 bytes_read=1062611 bytes_retransmit=9 bytes_invalid=0 send_seq=4567 receive_seq=4567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997570 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13194 bytes_read=77706 bytes_retransmit=9 bytes_invalid=0 send_seq=1398 receive_seq=1398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997587 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4261 bytes_read=139957 bytes_retransmit=9 bytes_invalid=0 send_seq=661 receive_seq=661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4855 bytes_read=14418 bytes_retransmit=9 bytes_invalid=0 send_seq=656 receive_seq=656 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47931 bytes_read=409832 bytes_retransmit=0 bytes_invalid=0 send_seq=4293 receive_seq=4293 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999895 adj=31998642 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.011 th0: temp=45.4 th1: temp=44.6 th2: temp=45.8 th3: temp=44.0 sysload=0.41 cputime=76.430 memavail=7407156 print_time=591.923 buffer_time=2.187 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 568.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6758736 bytes_read=833701 bytes_retransmit=9 bytes_invalid=0 send_seq=119110 receive_seq=119110 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=17425 freq=400015688 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4108 bytes_read=14689 bytes_retransmit=0 bytes_invalid=0 send_seq=656 receive_seq=656 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999312 adj=49996530 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34817 bytes_read=1065724 bytes_retransmit=9 bytes_invalid=0 send_seq=4578 receive_seq=4578 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997605 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13200 bytes_read=77806 bytes_retransmit=9 bytes_invalid=0 send_seq=1399 receive_seq=1399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997562 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4267 bytes_read=140206 bytes_retransmit=9 bytes_invalid=0 send_seq=662 receive_seq=662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4861 bytes_read=14434 bytes_retransmit=9 bytes_invalid=0 send_seq=657 receive_seq=657 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47937 bytes_read=410188 bytes_retransmit=0 bytes_invalid=0 send_seq=4294 receive_seq=4294 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998652 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.011 th0: temp=45.7 th1: temp=44.6 th2: temp=45.7 th3: temp=44.1 sysload=0.41 cputime=76.563 memavail=7407156 print_time=592.999 buffer_time=2.263 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 569.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6771272 bytes_read=835061 bytes_retransmit=9 bytes_invalid=0 send_seq=119320 receive_seq=119320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=18345 freq=400015705 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4114 bytes_read=14705 bytes_retransmit=0 bytes_invalid=0 send_seq=657 receive_seq=657 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999295 adj=49996549 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34893 bytes_read=1068925 bytes_retransmit=9 bytes_invalid=0 send_seq=4589 receive_seq=4589 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997616 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13206 bytes_read=77934 bytes_retransmit=9 bytes_invalid=0 send_seq=1400 receive_seq=1400 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997651 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4273 bytes_read=140500 bytes_retransmit=9 bytes_invalid=0 send_seq=663 receive_seq=663 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4867 bytes_read=14450 bytes_retransmit=9 bytes_invalid=0 send_seq=658 receive_seq=658 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47943 bytes_read=410544 bytes_retransmit=0 bytes_invalid=0 send_seq=4295 receive_seq=4295 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998674 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.011 th0: temp=45.7 th1: temp=44.6 th2: temp=45.7 th3: temp=43.9 sysload=0.41 cputime=76.694 memavail=7407156 print_time=594.076 buffer_time=2.339 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 570.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6783792 bytes_read=836427 bytes_retransmit=9 bytes_invalid=0 send_seq=119528 receive_seq=119528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=19274 freq=400015685 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4120 bytes_read=14734 bytes_retransmit=0 bytes_invalid=0 send_seq=658 receive_seq=658 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999279 adj=49996514 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34969 bytes_read=1072058 bytes_retransmit=9 bytes_invalid=0 send_seq=4600 receive_seq=4600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997581 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13212 bytes_read=78048 bytes_retransmit=9 bytes_invalid=0 send_seq=1401 receive_seq=1401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997573 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4279 bytes_read=140734 bytes_retransmit=9 bytes_invalid=0 send_seq=664 receive_seq=664 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4873 bytes_read=14466 bytes_retransmit=9 bytes_invalid=0 send_seq=659 receive_seq=659 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47949 bytes_read=410900 bytes_retransmit=0 bytes_invalid=0 send_seq=4296 receive_seq=4296 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998652 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.011 th0: temp=45.4 th1: temp=44.5 th2: temp=45.8 th3: temp=44.1 sysload=0.41 cputime=76.828 memavail=7406908 print_time=595.152 buffer_time=2.416 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 571.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6796305 bytes_read=837826 bytes_retransmit=9 bytes_invalid=0 send_seq=119740 receive_seq=119740 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=20202 freq=400015702 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4126 bytes_read=14750 bytes_retransmit=0 bytes_invalid=0 send_seq=659 receive_seq=659 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999262 adj=49996527 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35045 bytes_read=1075173 bytes_retransmit=9 bytes_invalid=0 send_seq=4611 receive_seq=4611 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997631 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13218 bytes_read=78148 bytes_retransmit=9 bytes_invalid=0 send_seq=1402 receive_seq=1402 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997572 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4285 bytes_read=140968 bytes_retransmit=9 bytes_invalid=0 send_seq=665 receive_seq=665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4879 bytes_read=14482 bytes_retransmit=9 bytes_invalid=0 send_seq=660 receive_seq=660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47955 bytes_read=411256 bytes_retransmit=0 bytes_invalid=0 send_seq=4297 receive_seq=4297 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998665 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.011 th0: temp=45.8 th1: temp=44.5 th2: temp=45.6 th3: temp=43.9 sysload=0.46 cputime=76.960 memavail=7406924 print_time=596.229 buffer_time=2.492 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 572.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6808841 bytes_read=839201 bytes_retransmit=9 bytes_invalid=0 send_seq=119953 receive_seq=119953 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=15022 freq=400015691 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4132 bytes_read=14766 bytes_retransmit=0 bytes_invalid=0 send_seq=660 receive_seq=660 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49996481 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35121 bytes_read=1078315 bytes_retransmit=9 bytes_invalid=0 send_seq=4622 receive_seq=4622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997652 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13224 bytes_read=78276 bytes_retransmit=9 bytes_invalid=0 send_seq=1403 receive_seq=1403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997518 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4291 bytes_read=141262 bytes_retransmit=9 bytes_invalid=0 send_seq=666 receive_seq=666 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997629 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4885 bytes_read=14509 bytes_retransmit=9 bytes_invalid=0 send_seq=661 receive_seq=661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47961 bytes_read=411612 bytes_retransmit=0 bytes_invalid=0 send_seq=4298 receive_seq=4298 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998646 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.011 th0: temp=45.9 th1: temp=44.7 th2: temp=45.4 th3: temp=44.0 sysload=0.46 cputime=77.075 memavail=7406924 print_time=596.767 buffer_time=2.030 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 573.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6821360 bytes_read=840566 bytes_retransmit=9 bytes_invalid=0 send_seq=120164 receive_seq=120164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=15966 freq=400015681 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4138 bytes_read=14782 bytes_retransmit=0 bytes_invalid=0 send_seq=661 receive_seq=661 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999227 adj=49996307 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35197 bytes_read=1081428 bytes_retransmit=9 bytes_invalid=0 send_seq=4633 receive_seq=4633 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997729 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13230 bytes_read=78376 bytes_retransmit=9 bytes_invalid=0 send_seq=1404 receive_seq=1404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997537 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4297 bytes_read=141511 bytes_retransmit=9 bytes_invalid=0 send_seq=667 receive_seq=667 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4891 bytes_read=14525 bytes_retransmit=9 bytes_invalid=0 send_seq=662 receive_seq=662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47967 bytes_read=411968 bytes_retransmit=0 bytes_invalid=0 send_seq=4299 receive_seq=4299 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998660 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.011 th0: temp=45.4 th1: temp=44.6 th2: temp=45.6 th3: temp=44.0 sysload=0.46 cputime=77.211 memavail=7406924 print_time=597.843 buffer_time=2.106 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 574.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6834378 bytes_read=842005 bytes_retransmit=9 bytes_invalid=0 send_seq=120384 receive_seq=120384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=16447 freq=400015668 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4144 bytes_read=14798 bytes_retransmit=0 bytes_invalid=0 send_seq=662 receive_seq=662 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49996219 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35273 bytes_read=1084543 bytes_retransmit=9 bytes_invalid=0 send_seq=4644 receive_seq=4644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997721 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13236 bytes_read=78476 bytes_retransmit=9 bytes_invalid=0 send_seq=1405 receive_seq=1405 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000018 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4303 bytes_read=141745 bytes_retransmit=9 bytes_invalid=0 send_seq=668 receive_seq=668 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4897 bytes_read=14541 bytes_retransmit=9 bytes_invalid=0 send_seq=663 receive_seq=663 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47973 bytes_read=412324 bytes_retransmit=0 bytes_invalid=0 send_seq=4300 receive_seq=4300 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998662 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.011 th0: temp=45.7 th1: temp=44.7 th2: temp=45.7 th3: temp=44.0 sysload=0.46 cputime=77.340 memavail=7406924 print_time=598.920 buffer_time=2.182 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 575.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6846921 bytes_read=843386 bytes_retransmit=9 bytes_invalid=0 send_seq=120595 receive_seq=120595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=17375 freq=400015648 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4150 bytes_read=14814 bytes_retransmit=0 bytes_invalid=0 send_seq=663 receive_seq=663 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999195 adj=49996279 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35342 bytes_read=1087678 bytes_retransmit=9 bytes_invalid=0 send_seq=4654 receive_seq=4654 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997731 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13242 bytes_read=78618 bytes_retransmit=9 bytes_invalid=0 send_seq=1406 receive_seq=1406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000017 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4309 bytes_read=142039 bytes_retransmit=9 bytes_invalid=0 send_seq=669 receive_seq=669 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4903 bytes_read=14557 bytes_retransmit=9 bytes_invalid=0 send_seq=664 receive_seq=664 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47979 bytes_read=412680 bytes_retransmit=0 bytes_invalid=0 send_seq=4301 receive_seq=4301 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998665 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.011 th0: temp=45.7 th1: temp=45.0 th2: temp=45.6 th3: temp=44.0 sysload=0.46 cputime=77.472 memavail=7405932 print_time=599.996 buffer_time=2.258 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 576.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6859450 bytes_read=844751 bytes_retransmit=9 bytes_invalid=0 send_seq=120806 receive_seq=120806 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=15 upcoming_bytes=18301 freq=400015639 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4156 bytes_read=14843 bytes_retransmit=0 bytes_invalid=0 send_seq=664 receive_seq=664 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999178 adj=49996345 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35418 bytes_read=1090793 bytes_retransmit=9 bytes_invalid=0 send_seq=4665 receive_seq=4665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997768 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13248 bytes_read=78718 bytes_retransmit=9 bytes_invalid=0 send_seq=1407 receive_seq=1407 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000016 adj=63997556 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4315 bytes_read=142273 bytes_retransmit=9 bytes_invalid=0 send_seq=670 receive_seq=670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4909 bytes_read=14573 bytes_retransmit=9 bytes_invalid=0 send_seq=665 receive_seq=665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47985 bytes_read=413036 bytes_retransmit=0 bytes_invalid=0 send_seq=4302 receive_seq=4302 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998681 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.011 th0: temp=45.4 th1: temp=44.6 th2: temp=45.7 th3: temp=44.0 sysload=0.42 cputime=77.604 memavail=7405932 print_time=601.073 buffer_time=2.334 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 577.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6871979 bytes_read=846145 bytes_retransmit=9 bytes_invalid=0 send_seq=121017 receive_seq=121017 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=19224 freq=400015632 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4162 bytes_read=14859 bytes_retransmit=0 bytes_invalid=0 send_seq=665 receive_seq=665 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999162 adj=49996357 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35494 bytes_read=1093969 bytes_retransmit=9 bytes_invalid=0 send_seq=4676 receive_seq=4676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997831 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13254 bytes_read=78818 bytes_retransmit=9 bytes_invalid=0 send_seq=1408 receive_seq=1408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000016 adj=63997549 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4321 bytes_read=142507 bytes_retransmit=9 bytes_invalid=0 send_seq=671 receive_seq=671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997698 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4915 bytes_read=14600 bytes_retransmit=9 bytes_invalid=0 send_seq=666 receive_seq=666 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999455 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47991 bytes_read=413392 bytes_retransmit=0 bytes_invalid=0 send_seq=4303 receive_seq=4303 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998684 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.011 th0: temp=45.6 th1: temp=44.6 th2: temp=45.7 th3: temp=44.2 sysload=0.42 cputime=77.738 memavail=7405960 print_time=602.149 buffer_time=2.411 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 578.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6884494 bytes_read=847515 bytes_retransmit=9 bytes_invalid=0 send_seq=121229 receive_seq=121229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=20152 freq=400015645 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4168 bytes_read=14875 bytes_retransmit=0 bytes_invalid=0 send_seq=666 receive_seq=666 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999145 adj=49996364 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35570 bytes_read=1097114 bytes_retransmit=9 bytes_invalid=0 send_seq=4687 receive_seq=4687 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997780 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13260 bytes_read=78946 bytes_retransmit=9 bytes_invalid=0 send_seq=1409 receive_seq=1409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000016 adj=63997559 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4327 bytes_read=142816 bytes_retransmit=9 bytes_invalid=0 send_seq=672 receive_seq=672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997707 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4921 bytes_read=14616 bytes_retransmit=9 bytes_invalid=0 send_seq=667 receive_seq=667 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=47997 bytes_read=413748 bytes_retransmit=0 bytes_invalid=0 send_seq=4304 receive_seq=4304 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998677 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=45.9 th1: temp=44.9 th2: temp=45.9 th3: temp=44.1 sysload=0.42 cputime=77.873 memavail=7405960 print_time=603.226 buffer_time=2.487 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 579.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6897015 bytes_read=848868 bytes_retransmit=9 bytes_invalid=0 send_seq=121439 receive_seq=121439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=14989 freq=400015642 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4174 bytes_read=14891 bytes_retransmit=0 bytes_invalid=0 send_seq=667 receive_seq=667 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999128 adj=49996343 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35646 bytes_read=1100228 bytes_retransmit=9 bytes_invalid=0 send_seq=4698 receive_seq=4698 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997727 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13266 bytes_read=79046 bytes_retransmit=9 bytes_invalid=0 send_seq=1410 receive_seq=1410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000014 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4333 bytes_read=143050 bytes_retransmit=9 bytes_invalid=0 send_seq=673 receive_seq=673 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4927 bytes_read=14632 bytes_retransmit=9 bytes_invalid=0 send_seq=668 receive_seq=668 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48003 bytes_read=414104 bytes_retransmit=0 bytes_invalid=0 send_seq=4305 receive_seq=4305 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998670 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=45.8 th1: temp=44.9 th2: temp=45.7 th3: temp=43.9 sysload=0.42 cputime=77.999 memavail=7407352 print_time=603.764 buffer_time=2.025 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 580.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6909546 bytes_read=850283 bytes_retransmit=9 bytes_invalid=0 send_seq=121651 receive_seq=121651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=15900 freq=400015639 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4180 bytes_read=14907 bytes_retransmit=0 bytes_invalid=0 send_seq=668 receive_seq=668 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999111 adj=49996149 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35722 bytes_read=1103359 bytes_retransmit=9 bytes_invalid=0 send_seq=4709 receive_seq=4709 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997895 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13272 bytes_read=79158 bytes_retransmit=9 bytes_invalid=0 send_seq=1411 receive_seq=1411 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000014 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4339 bytes_read=143284 bytes_retransmit=9 bytes_invalid=0 send_seq=674 receive_seq=674 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4933 bytes_read=14648 bytes_retransmit=9 bytes_invalid=0 send_seq=669 receive_seq=669 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48009 bytes_read=414460 bytes_retransmit=0 bytes_invalid=0 send_seq=4306 receive_seq=4306 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998670 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=46.0 th1: temp=44.8 th2: temp=45.7 th3: temp=44.1 sysload=0.42 cputime=78.130 memavail=7407352 print_time=604.840 buffer_time=2.101 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 581.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6922576 bytes_read=851688 bytes_retransmit=9 bytes_invalid=0 send_seq=121870 receive_seq=121870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=16381 freq=400015628 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4186 bytes_read=14936 bytes_retransmit=0 bytes_invalid=0 send_seq=669 receive_seq=669 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999095 adj=49996069 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35798 bytes_read=1106481 bytes_retransmit=9 bytes_invalid=0 send_seq=4720 receive_seq=4720 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997831 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13278 bytes_read=79277 bytes_retransmit=9 bytes_invalid=0 send_seq=1412 receive_seq=1412 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4345 bytes_read=143578 bytes_retransmit=9 bytes_invalid=0 send_seq=675 receive_seq=675 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4939 bytes_read=14664 bytes_retransmit=9 bytes_invalid=0 send_seq=670 receive_seq=670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48015 bytes_read=414816 bytes_retransmit=0 bytes_invalid=0 send_seq=4307 receive_seq=4307 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998666 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.011 th0: temp=45.7 th1: temp=44.8 th2: temp=46.0 th3: temp=44.1 sysload=0.47 cputime=78.263 memavail=7407356 print_time=605.917 buffer_time=2.177 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 582.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6935102 bytes_read=853053 bytes_retransmit=9 bytes_invalid=0 send_seq=122081 receive_seq=122081 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=17309 freq=400015625 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4192 bytes_read=14952 bytes_retransmit=0 bytes_invalid=0 send_seq=670 receive_seq=670 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999079 adj=49996138 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35874 bytes_read=1109578 bytes_retransmit=9 bytes_invalid=0 send_seq=4731 receive_seq=4731 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997797 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13284 bytes_read=79370 bytes_retransmit=9 bytes_invalid=0 send_seq=1413 receive_seq=1413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997638 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4351 bytes_read=143812 bytes_retransmit=9 bytes_invalid=0 send_seq=676 receive_seq=676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997778 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4945 bytes_read=14691 bytes_retransmit=9 bytes_invalid=0 send_seq=671 receive_seq=671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48021 bytes_read=415172 bytes_retransmit=0 bytes_invalid=0 send_seq=4308 receive_seq=4308 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999897 adj=31998674 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=45.9 th1: temp=44.7 th2: temp=45.9 th3: temp=44.0 sysload=0.47 cputime=78.472 memavail=7407368 print_time=606.993 buffer_time=2.253 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 583.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6947620 bytes_read=854437 bytes_retransmit=9 bytes_invalid=0 send_seq=122290 receive_seq=122290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=18237 freq=400015623 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4198 bytes_read=14968 bytes_retransmit=0 bytes_invalid=0 send_seq=671 receive_seq=671 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999063 adj=49996180 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35950 bytes_read=1112675 bytes_retransmit=9 bytes_invalid=0 send_seq=4742 receive_seq=4742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997744 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13290 bytes_read=79463 bytes_retransmit=9 bytes_invalid=0 send_seq=1414 receive_seq=1414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997600 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4357 bytes_read=144061 bytes_retransmit=9 bytes_invalid=0 send_seq=677 receive_seq=677 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997749 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4951 bytes_read=14707 bytes_retransmit=9 bytes_invalid=0 send_seq=672 receive_seq=672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48027 bytes_read=415528 bytes_retransmit=0 bytes_invalid=0 send_seq=4309 receive_seq=4309 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999897 adj=31998682 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=45.9 th1: temp=44.8 th2: temp=45.8 th3: temp=44.1 sysload=0.47 cputime=78.604 memavail=7407368 print_time=608.070 buffer_time=2.329 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 584.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6960164 bytes_read=855807 bytes_retransmit=9 bytes_invalid=0 send_seq=122502 receive_seq=122502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=19158 freq=400015631 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4204 bytes_read=14984 bytes_retransmit=0 bytes_invalid=0 send_seq=672 receive_seq=672 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999047 adj=49996204 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36026 bytes_read=1115799 bytes_retransmit=9 bytes_invalid=0 send_seq=4753 receive_seq=4753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997701 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13296 bytes_read=79584 bytes_retransmit=9 bytes_invalid=0 send_seq=1415 receive_seq=1415 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997569 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4363 bytes_read=144355 bytes_retransmit=9 bytes_invalid=0 send_seq=678 receive_seq=678 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997726 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4957 bytes_read=14723 bytes_retransmit=9 bytes_invalid=0 send_seq=673 receive_seq=673 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48033 bytes_read=415884 bytes_retransmit=0 bytes_invalid=0 send_seq=4310 receive_seq=4310 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998679 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=45.9 th1: temp=44.9 th2: temp=45.8 th3: temp=44.0 sysload=0.47 cputime=78.738 memavail=7407368 print_time=609.146 buffer_time=2.406 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 585.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6972695 bytes_read=857188 bytes_retransmit=9 bytes_invalid=0 send_seq=122714 receive_seq=122713 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=20086 freq=400015628 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4210 bytes_read=15000 bytes_retransmit=0 bytes_invalid=0 send_seq=673 receive_seq=673 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999031 adj=49996202 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36102 bytes_read=1118991 bytes_retransmit=9 bytes_invalid=0 send_seq=4764 receive_seq=4764 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997707 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13302 bytes_read=79698 bytes_retransmit=9 bytes_invalid=0 send_seq=1416 receive_seq=1416 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4369 bytes_read=144589 bytes_retransmit=9 bytes_invalid=0 send_seq=679 receive_seq=679 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997736 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4963 bytes_read=14739 bytes_retransmit=9 bytes_invalid=0 send_seq=674 receive_seq=674 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48039 bytes_read=416240 bytes_retransmit=0 bytes_invalid=0 send_seq=4311 receive_seq=4311 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998698 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=45.9 th1: temp=44.7 th2: temp=45.8 th3: temp=44.1 sysload=0.47 cputime=78.877 memavail=7406904 print_time=610.223 buffer_time=2.482 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 586.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6985213 bytes_read=858587 bytes_retransmit=9 bytes_invalid=0 send_seq=122925 receive_seq=122925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=14906 freq=400015631 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4216 bytes_read=15029 bytes_retransmit=0 bytes_invalid=0 send_seq=674 receive_seq=674 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999016 adj=49996216 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36178 bytes_read=1122107 bytes_retransmit=9 bytes_invalid=0 send_seq=4775 receive_seq=4775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997715 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13308 bytes_read=79798 bytes_retransmit=9 bytes_invalid=0 send_seq=1417 receive_seq=1417 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000018 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4375 bytes_read=144823 bytes_retransmit=9 bytes_invalid=0 send_seq=680 receive_seq=680 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997715 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4969 bytes_read=14755 bytes_retransmit=9 bytes_invalid=0 send_seq=675 receive_seq=675 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48045 bytes_read=416596 bytes_retransmit=0 bytes_invalid=0 send_seq=4312 receive_seq=4312 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998696 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=45.8 th1: temp=44.6 th2: temp=45.9 th3: temp=44.3 sysload=0.43 cputime=78.992 memavail=7406904 print_time=610.761 buffer_time=2.020 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 587.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=6997734 bytes_read=859947 bytes_retransmit=9 bytes_invalid=0 send_seq=123135 receive_seq=123135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=15834 freq=400015626 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4222 bytes_read=15045 bytes_retransmit=0 bytes_invalid=0 send_seq=675 receive_seq=675 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999001 adj=49996033 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36247 bytes_read=1125227 bytes_retransmit=9 bytes_invalid=0 send_seq=4785 receive_seq=4785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997682 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13314 bytes_read=79926 bytes_retransmit=9 bytes_invalid=0 send_seq=1418 receive_seq=1418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000017 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4381 bytes_read=145117 bytes_retransmit=9 bytes_invalid=0 send_seq=681 receive_seq=681 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997718 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4975 bytes_read=14782 bytes_retransmit=9 bytes_invalid=0 send_seq=676 receive_seq=676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48051 bytes_read=416952 bytes_retransmit=0 bytes_invalid=0 send_seq=4313 receive_seq=4313 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998691 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=46.0 th1: temp=44.8 th2: temp=46.0 th3: temp=44.1 sysload=0.43 cputime=79.124 memavail=7406904 print_time=611.837 buffer_time=2.095 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 588.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7010702 bytes_read=861347 bytes_retransmit=9 bytes_invalid=0 send_seq=123353 receive_seq=123353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=16314 freq=400015616 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4228 bytes_read=15061 bytes_retransmit=0 bytes_invalid=0 send_seq=676 receive_seq=676 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998986 adj=49995985 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36323 bytes_read=1128341 bytes_retransmit=9 bytes_invalid=0 send_seq=4796 receive_seq=4796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997656 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13320 bytes_read=80026 bytes_retransmit=9 bytes_invalid=0 send_seq=1419 receive_seq=1419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000015 adj=63997518 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4387 bytes_read=145366 bytes_retransmit=9 bytes_invalid=0 send_seq=682 receive_seq=682 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999531 adj=47997713 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4981 bytes_read=14798 bytes_retransmit=9 bytes_invalid=0 send_seq=677 receive_seq=677 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48057 bytes_read=417308 bytes_retransmit=0 bytes_invalid=0 send_seq=4314 receive_seq=4314 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998691 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=45.7 th1: temp=45.0 th2: temp=45.8 th3: temp=44.1 sysload=0.43 cputime=79.257 memavail=7406904 print_time=612.914 buffer_time=2.171 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 589.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7023245 bytes_read=862749 bytes_retransmit=9 bytes_invalid=0 send_seq=123566 receive_seq=123566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=17242 freq=400015620 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4234 bytes_read=15077 bytes_retransmit=0 bytes_invalid=0 send_seq=677 receive_seq=677 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998971 adj=49996064 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36399 bytes_read=1131457 bytes_retransmit=9 bytes_invalid=0 send_seq=4807 receive_seq=4807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997650 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13326 bytes_read=80126 bytes_retransmit=9 bytes_invalid=0 send_seq=1420 receive_seq=1420 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997517 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4393 bytes_read=145600 bytes_retransmit=9 bytes_invalid=0 send_seq=683 receive_seq=683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997731 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4987 bytes_read=14814 bytes_retransmit=9 bytes_invalid=0 send_seq=678 receive_seq=678 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48063 bytes_read=417664 bytes_retransmit=0 bytes_invalid=0 send_seq=4315 receive_seq=4315 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998689 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=46.2 th1: temp=44.2 th2: temp=45.9 th3: temp=44.2 sysload=0.43 cputime=79.391 memavail=7406904 print_time=613.990 buffer_time=2.248 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 590.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7035769 bytes_read=864132 bytes_retransmit=9 bytes_invalid=0 send_seq=123778 receive_seq=123778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=18170 freq=400015681 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4240 bytes_read=15093 bytes_retransmit=0 bytes_invalid=0 send_seq=678 receive_seq=678 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998957 adj=49996102 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36475 bytes_read=1134617 bytes_retransmit=9 bytes_invalid=0 send_seq=4818 receive_seq=4818 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997705 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13332 bytes_read=80268 bytes_retransmit=9 bytes_invalid=0 send_seq=1421 receive_seq=1421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997688 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4399 bytes_read=145894 bytes_retransmit=9 bytes_invalid=0 send_seq=684 receive_seq=684 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999535 adj=47997772 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4993 bytes_read=14830 bytes_retransmit=9 bytes_invalid=0 send_seq=679 receive_seq=679 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48069 bytes_read=418020 bytes_retransmit=0 bytes_invalid=0 send_seq=4316 receive_seq=4316 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998669 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=46.1 th1: temp=44.9 th2: temp=45.9 th3: temp=44.1 sysload=0.43 cputime=79.530 memavail=7406904 print_time=615.067 buffer_time=2.324 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 591.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7048379 bytes_read=865517 bytes_retransmit=9 bytes_invalid=0 send_seq=123993 receive_seq=123993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=19091 freq=400015660 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4246 bytes_read=15122 bytes_retransmit=0 bytes_invalid=0 send_seq=679 receive_seq=679 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998943 adj=49996045 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36551 bytes_read=1137732 bytes_retransmit=9 bytes_invalid=0 send_seq=4829 receive_seq=4829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997559 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13338 bytes_read=80368 bytes_retransmit=9 bytes_invalid=0 send_seq=1422 receive_seq=1422 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997522 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4405 bytes_read=146128 bytes_retransmit=9 bytes_invalid=0 send_seq=685 receive_seq=685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=4999 bytes_read=14846 bytes_retransmit=9 bytes_invalid=0 send_seq=680 receive_seq=680 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48075 bytes_read=418376 bytes_retransmit=0 bytes_invalid=0 send_seq=4317 receive_seq=4317 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998618 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=46.0 th1: temp=44.9 th2: temp=45.6 th3: temp=44.2 sysload=0.40 cputime=79.670 memavail=7406920 print_time=616.143 buffer_time=2.400 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 592.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7060890 bytes_read=866896 bytes_retransmit=9 bytes_invalid=0 send_seq=124201 receive_seq=124201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=20019 freq=400015654 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4252 bytes_read=15138 bytes_retransmit=0 bytes_invalid=0 send_seq=680 receive_seq=680 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998928 adj=49996116 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36627 bytes_read=1140846 bytes_retransmit=9 bytes_invalid=0 send_seq=4840 receive_seq=4840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997706 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13344 bytes_read=80468 bytes_retransmit=9 bytes_invalid=0 send_seq=1423 receive_seq=1423 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997537 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4411 bytes_read=146362 bytes_retransmit=9 bytes_invalid=0 send_seq=686 receive_seq=686 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997669 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5005 bytes_read=14873 bytes_retransmit=9 bytes_invalid=0 send_seq=681 receive_seq=681 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48081 bytes_read=418732 bytes_retransmit=0 bytes_invalid=0 send_seq=4318 receive_seq=4318 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998641 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=46.0 th1: temp=44.4 th2: temp=45.6 th3: temp=44.7 sysload=0.40 cputime=79.801 memavail=7406944 print_time=617.220 buffer_time=2.476 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 593.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7073441 bytes_read=868286 bytes_retransmit=9 bytes_invalid=0 send_seq=124417 receive_seq=124417 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=14839 freq=400015649 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4258 bytes_read=15154 bytes_retransmit=0 bytes_invalid=0 send_seq=681 receive_seq=681 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998913 adj=49996142 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36703 bytes_read=1144046 bytes_retransmit=9 bytes_invalid=0 send_seq=4851 receive_seq=4851 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997677 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13350 bytes_read=80596 bytes_retransmit=9 bytes_invalid=0 send_seq=1424 receive_seq=1424 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4417 bytes_read=146671 bytes_retransmit=9 bytes_invalid=0 send_seq=687 receive_seq=687 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5011 bytes_read=14889 bytes_retransmit=9 bytes_invalid=0 send_seq=682 receive_seq=682 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48087 bytes_read=419088 bytes_retransmit=0 bytes_invalid=0 send_seq=4319 receive_seq=4319 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998640 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.011 th0: temp=45.7 th1: temp=44.9 th2: temp=46.1 th3: temp=44.3 sysload=0.40 cputime=79.927 memavail=7406944 print_time=617.758 buffer_time=2.013 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 594.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7085972 bytes_read=869656 bytes_retransmit=9 bytes_invalid=0 send_seq=124629 receive_seq=124629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=15751 freq=400015633 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4264 bytes_read=15170 bytes_retransmit=0 bytes_invalid=0 send_seq=682 receive_seq=682 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998900 adj=49995980 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36779 bytes_read=1147159 bytes_retransmit=9 bytes_invalid=0 send_seq=4862 receive_seq=4862 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997648 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13356 bytes_read=80696 bytes_retransmit=9 bytes_invalid=0 send_seq=1425 receive_seq=1425 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4423 bytes_read=146905 bytes_retransmit=9 bytes_invalid=0 send_seq=688 receive_seq=688 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999531 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5017 bytes_read=14905 bytes_retransmit=9 bytes_invalid=0 send_seq=683 receive_seq=683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48093 bytes_read=419444 bytes_retransmit=0 bytes_invalid=0 send_seq=4320 receive_seq=4320 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998646 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.011 th0: temp=45.9 th1: temp=45.0 th2: temp=46.0 th3: temp=44.2 sysload=0.40 cputime=80.059 memavail=7406956 print_time=618.834 buffer_time=2.088 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 595.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7098997 bytes_read=871101 bytes_retransmit=9 bytes_invalid=0 send_seq=124847 receive_seq=124847 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=16231 freq=400015654 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4270 bytes_read=15186 bytes_retransmit=0 bytes_invalid=0 send_seq=683 receive_seq=683 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998886 adj=49995954 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36855 bytes_read=1150291 bytes_retransmit=9 bytes_invalid=0 send_seq=4873 receive_seq=4873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997651 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13362 bytes_read=80810 bytes_retransmit=9 bytes_invalid=0 send_seq=1426 receive_seq=1426 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997517 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4429 bytes_read=147139 bytes_retransmit=9 bytes_invalid=0 send_seq=689 receive_seq=689 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999531 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5023 bytes_read=14921 bytes_retransmit=9 bytes_invalid=0 send_seq=684 receive_seq=684 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48099 bytes_read=419800 bytes_retransmit=0 bytes_invalid=0 send_seq=4321 receive_seq=4321 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999902 adj=31998674 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.011 th0: temp=45.9 th1: temp=45.0 th2: temp=46.2 th3: temp=44.1 sysload=0.40 cputime=80.195 memavail=7406956 print_time=619.911 buffer_time=2.164 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 596.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7111501 bytes_read=872461 bytes_retransmit=9 bytes_invalid=0 send_seq=125057 receive_seq=125057 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=17143 freq=400015646 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4276 bytes_read=15215 bytes_retransmit=0 bytes_invalid=0 send_seq=684 receive_seq=684 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998873 adj=49995989 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36931 bytes_read=1153433 bytes_retransmit=9 bytes_invalid=0 send_seq=4884 receive_seq=4884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997583 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13368 bytes_read=80938 bytes_retransmit=9 bytes_invalid=0 send_seq=1427 receive_seq=1427 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000018 adj=63997468 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4435 bytes_read=147433 bytes_retransmit=9 bytes_invalid=0 send_seq=690 receive_seq=690 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5029 bytes_read=14937 bytes_retransmit=9 bytes_invalid=0 send_seq=685 receive_seq=685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48105 bytes_read=420156 bytes_retransmit=0 bytes_invalid=0 send_seq=4322 receive_seq=4322 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999902 adj=31998671 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=45.9 th1: temp=44.9 th2: temp=46.0 th3: temp=44.4 sysload=0.37 cputime=80.337 memavail=7401336 print_time=620.987 buffer_time=2.240 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 597.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7124051 bytes_read=873840 bytes_retransmit=9 bytes_invalid=0 send_seq=125268 receive_seq=125268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=18071 freq=400015636 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4282 bytes_read=15231 bytes_retransmit=0 bytes_invalid=0 send_seq=685 receive_seq=685 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998861 adj=49996052 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37007 bytes_read=1156548 bytes_retransmit=9 bytes_invalid=0 send_seq=4895 receive_seq=4895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997610 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13374 bytes_read=81038 bytes_retransmit=9 bytes_invalid=0 send_seq=1428 receive_seq=1428 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000018 adj=63997479 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4441 bytes_read=147667 bytes_retransmit=9 bytes_invalid=0 send_seq=691 receive_seq=691 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5035 bytes_read=14964 bytes_retransmit=9 bytes_invalid=0 send_seq=686 receive_seq=686 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48111 bytes_read=420512 bytes_retransmit=0 bytes_invalid=0 send_seq=4323 receive_seq=4323 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998665 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.011 th0: temp=45.9 th1: temp=44.7 th2: temp=45.9 th3: temp=44.3 sysload=0.37 cputime=80.471 memavail=7407980 print_time=622.064 buffer_time=2.316 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 598.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7136535 bytes_read=875220 bytes_retransmit=9 bytes_invalid=0 send_seq=125479 receive_seq=125479 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=19009 freq=400015624 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4288 bytes_read=15247 bytes_retransmit=0 bytes_invalid=0 send_seq=686 receive_seq=686 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998848 adj=49996111 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37083 bytes_read=1159663 bytes_retransmit=9 bytes_invalid=0 send_seq=4906 receive_seq=4906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997689 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13380 bytes_read=81138 bytes_retransmit=9 bytes_invalid=0 send_seq=1429 receive_seq=1429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000016 adj=63997494 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4447 bytes_read=147916 bytes_retransmit=9 bytes_invalid=0 send_seq=692 receive_seq=692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5041 bytes_read=14980 bytes_retransmit=9 bytes_invalid=0 send_seq=687 receive_seq=687 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48117 bytes_read=420868 bytes_retransmit=0 bytes_invalid=0 send_seq=4324 receive_seq=4324 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998663 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.011 th0: temp=45.9 th1: temp=45.2 th2: temp=46.1 th3: temp=44.3 sysload=0.37 cputime=80.605 memavail=7407980 print_time=623.140 buffer_time=2.393 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 599.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7149081 bytes_read=876605 bytes_retransmit=9 bytes_invalid=0 send_seq=125694 receive_seq=125694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=19937 freq=400015608 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4294 bytes_read=15263 bytes_retransmit=0 bytes_invalid=0 send_seq=687 receive_seq=687 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998836 adj=49996158 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37152 bytes_read=1162781 bytes_retransmit=9 bytes_invalid=0 send_seq=4916 receive_seq=4916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997732 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13386 bytes_read=81266 bytes_retransmit=9 bytes_invalid=0 send_seq=1430 receive_seq=1430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000015 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4453 bytes_read=148210 bytes_retransmit=9 bytes_invalid=0 send_seq=693 receive_seq=693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5047 bytes_read=14996 bytes_retransmit=9 bytes_invalid=0 send_seq=688 receive_seq=688 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48123 bytes_read=421224 bytes_retransmit=0 bytes_invalid=0 send_seq=4325 receive_seq=4325 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998664 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.011 th0: temp=45.9 th1: temp=45.0 th2: temp=46.1 th3: temp=44.4 sysload=0.37 cputime=80.742 memavail=7407980 print_time=624.217 buffer_time=2.468 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 600.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7161627 bytes_read=878017 bytes_retransmit=9 bytes_invalid=0 send_seq=125909 receive_seq=125909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=14757 freq=400015603 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4300 bytes_read=15279 bytes_retransmit=0 bytes_invalid=0 send_seq=688 receive_seq=688 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998825 adj=49996200 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37228 bytes_read=1165912 bytes_retransmit=9 bytes_invalid=0 send_seq=4927 receive_seq=4927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997719 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13392 bytes_read=81366 bytes_retransmit=9 bytes_invalid=0 send_seq=1431 receive_seq=1431 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000014 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4459 bytes_read=148444 bytes_retransmit=9 bytes_invalid=0 send_seq=694 receive_seq=694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5053 bytes_read=15012 bytes_retransmit=9 bytes_invalid=0 send_seq=689 receive_seq=689 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48129 bytes_read=421580 bytes_retransmit=0 bytes_invalid=0 send_seq=4326 receive_seq=4326 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998685 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.011 th0: temp=46.0 th1: temp=45.1 th2: temp=45.9 th3: temp=44.4 sysload=0.37 cputime=80.863 memavail=7407980 print_time=624.755 buffer_time=2.006 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 601.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7174158 bytes_read=879400 bytes_retransmit=9 bytes_invalid=0 send_seq=126121 receive_seq=126121 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=15668 freq=400015590 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4306 bytes_read=15308 bytes_retransmit=0 bytes_invalid=0 send_seq=689 receive_seq=689 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998813 adj=49996070 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37304 bytes_read=1169091 bytes_retransmit=9 bytes_invalid=0 send_seq=4938 receive_seq=4938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997704 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13398 bytes_read=81480 bytes_retransmit=9 bytes_invalid=0 send_seq=1432 receive_seq=1432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000014 adj=63997515 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4465 bytes_read=148678 bytes_retransmit=9 bytes_invalid=0 send_seq=695 receive_seq=695 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997677 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5059 bytes_read=15028 bytes_retransmit=9 bytes_invalid=0 send_seq=690 receive_seq=690 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48135 bytes_read=421936 bytes_retransmit=0 bytes_invalid=0 send_seq=4327 receive_seq=4327 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999902 adj=31998693 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.011 th0: temp=46.1 th1: temp=45.0 th2: temp=46.2 th3: temp=44.1 sysload=0.34 cputime=80.997 memavail=7407980 print_time=625.832 buffer_time=2.082 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 602.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7187203 bytes_read=880820 bytes_retransmit=9 bytes_invalid=0 send_seq=126343 receive_seq=126343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=16149 freq=400015574 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4312 bytes_read=15324 bytes_retransmit=0 bytes_invalid=0 send_seq=690 receive_seq=690 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998802 adj=49996048 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37380 bytes_read=1172234 bytes_retransmit=9 bytes_invalid=0 send_seq=4949 receive_seq=4949 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997709 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13404 bytes_read=81608 bytes_retransmit=9 bytes_invalid=0 send_seq=1433 receive_seq=1433 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000013 adj=63997550 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4471 bytes_read=148961 bytes_retransmit=9 bytes_invalid=0 send_seq=696 receive_seq=696 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5065 bytes_read=15055 bytes_retransmit=9 bytes_invalid=0 send_seq=691 receive_seq=691 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48141 bytes_read=422292 bytes_retransmit=0 bytes_invalid=0 send_seq=4328 receive_seq=4328 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999903 adj=31998709 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.011 th0: temp=46.1 th1: temp=44.8 th2: temp=46.1 th3: temp=44.4 sysload=0.34 cputime=81.130 memavail=7407980 print_time=626.908 buffer_time=2.158 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 603.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7199724 bytes_read=882194 bytes_retransmit=9 bytes_invalid=0 send_seq=126553 receive_seq=126553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=17077 freq=400015567 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4318 bytes_read=15340 bytes_retransmit=0 bytes_invalid=0 send_seq=691 receive_seq=691 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998791 adj=49996125 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37456 bytes_read=1175347 bytes_retransmit=9 bytes_invalid=0 send_seq=4960 receive_seq=4960 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997726 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13410 bytes_read=81708 bytes_retransmit=9 bytes_invalid=0 send_seq=1434 receive_seq=1434 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000012 adj=63997556 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4477 bytes_read=149194 bytes_retransmit=9 bytes_invalid=0 send_seq=697 receive_seq=697 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997719 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5071 bytes_read=15071 bytes_retransmit=9 bytes_invalid=0 send_seq=692 receive_seq=692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48147 bytes_read=422648 bytes_retransmit=0 bytes_invalid=0 send_seq=4329 receive_seq=4329 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999904 adj=31998723 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=46.1 th1: temp=44.8 th2: temp=46.2 th3: temp=44.2 sysload=0.34 cputime=81.264 memavail=7407980 print_time=627.984 buffer_time=2.235 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 604.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7212233 bytes_read=883575 bytes_retransmit=9 bytes_invalid=0 send_seq=126762 receive_seq=126762 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=18005 freq=400015592 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4330 bytes_read=15372 bytes_retransmit=0 bytes_invalid=0 send_seq=693 receive_seq=693 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998770 adj=49996171 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37538 bytes_read=1178477 bytes_retransmit=9 bytes_invalid=0 send_seq=4972 receive_seq=4972 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997704 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13422 bytes_read=81824 bytes_retransmit=9 bytes_invalid=0 send_seq=1436 receive_seq=1436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000013 adj=63997552 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4489 bytes_read=149427 bytes_retransmit=9 bytes_invalid=0 send_seq=699 receive_seq=699 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997714 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5083 bytes_read=15103 bytes_retransmit=9 bytes_invalid=0 send_seq=694 receive_seq=694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48159 bytes_read=423020 bytes_retransmit=0 bytes_invalid=0 send_seq=4331 receive_seq=4331 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999904 adj=31998730 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=46.3 th1: temp=44.7 th2: temp=46.1 th3: temp=44.4 sysload=0.34 cputime=81.398 memavail=7407980 print_time=629.061 buffer_time=2.311 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 605.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7224807 bytes_read=884956 bytes_retransmit=9 bytes_invalid=0 send_seq=126973 receive_seq=126973 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=18926 freq=400015583 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4336 bytes_read=15388 bytes_retransmit=0 bytes_invalid=0 send_seq=694 receive_seq=694 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998760 adj=49996035 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37614 bytes_read=1181636 bytes_retransmit=9 bytes_invalid=0 send_seq=4983 receive_seq=4983 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997675 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13428 bytes_read=81952 bytes_retransmit=9 bytes_invalid=0 send_seq=1437 receive_seq=1437 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000011 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4495 bytes_read=149701 bytes_retransmit=9 bytes_invalid=0 send_seq=700 receive_seq=700 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5089 bytes_read=15119 bytes_retransmit=9 bytes_invalid=0 send_seq=695 receive_seq=695 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48165 bytes_read=423376 bytes_retransmit=0 bytes_invalid=0 send_seq=4332 receive_seq=4332 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999904 adj=31998693 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.011 th0: temp=45.7 th1: temp=44.9 th2: temp=46.1 th3: temp=44.4 sysload=0.34 cputime=81.537 memavail=7406972 print_time=630.137 buffer_time=2.387 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 606.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7237312 bytes_read=886330 bytes_retransmit=9 bytes_invalid=0 send_seq=127183 receive_seq=127183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=19854 freq=400015602 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4342 bytes_read=15417 bytes_retransmit=0 bytes_invalid=0 send_seq=695 receive_seq=695 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998751 adj=49996103 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37690 bytes_read=1184750 bytes_retransmit=9 bytes_invalid=0 send_seq=4994 receive_seq=4994 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997681 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13434 bytes_read=82066 bytes_retransmit=9 bytes_invalid=0 send_seq=1438 receive_seq=1438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000011 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4501 bytes_read=149919 bytes_retransmit=9 bytes_invalid=0 send_seq=701 receive_seq=701 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5095 bytes_read=15135 bytes_retransmit=9 bytes_invalid=0 send_seq=696 receive_seq=696 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48171 bytes_read=423732 bytes_retransmit=0 bytes_invalid=0 send_seq=4333 receive_seq=4333 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999903 adj=31998689 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=46.0 th1: temp=45.0 th2: temp=46.3 th3: temp=44.3 sysload=0.39 cputime=81.666 memavail=7407000 print_time=631.214 buffer_time=2.463 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 607.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7249818 bytes_read=887715 bytes_retransmit=9 bytes_invalid=0 send_seq=127395 receive_seq=127395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=14690 freq=400015601 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4348 bytes_read=15433 bytes_retransmit=0 bytes_invalid=0 send_seq=696 receive_seq=696 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998741 adj=49996122 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37766 bytes_read=1187864 bytes_retransmit=9 bytes_invalid=0 send_seq=5005 receive_seq=5005 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997627 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13440 bytes_read=82166 bytes_retransmit=9 bytes_invalid=0 send_seq=1439 receive_seq=1439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000010 adj=63997474 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4507 bytes_read=150137 bytes_retransmit=9 bytes_invalid=0 send_seq=702 receive_seq=702 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5101 bytes_read=15162 bytes_retransmit=9 bytes_invalid=0 send_seq=697 receive_seq=697 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48177 bytes_read=424088 bytes_retransmit=0 bytes_invalid=0 send_seq=4334 receive_seq=4334 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999903 adj=31998657 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.011 th0: temp=46.2 th1: temp=44.9 th2: temp=46.6 th3: temp=44.5 sysload=0.39 cputime=81.780 memavail=7407000 print_time=631.752 buffer_time=2.001 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 608.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7262356 bytes_read=889085 bytes_retransmit=9 bytes_invalid=0 send_seq=127607 receive_seq=127607 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=15602 freq=400015585 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4354 bytes_read=15449 bytes_retransmit=0 bytes_invalid=0 send_seq=697 receive_seq=697 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998733 adj=49996017 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37842 bytes_read=1191006 bytes_retransmit=9 bytes_invalid=0 send_seq=5016 receive_seq=5016 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000181 adj=63997601 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13446 bytes_read=82294 bytes_retransmit=9 bytes_invalid=0 send_seq=1440 receive_seq=1440 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997462 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4513 bytes_read=150442 bytes_retransmit=9 bytes_invalid=0 send_seq=703 receive_seq=703 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997623 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5107 bytes_read=15178 bytes_retransmit=9 bytes_invalid=0 send_seq=698 receive_seq=698 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48183 bytes_read=424444 bytes_retransmit=0 bytes_invalid=0 send_seq=4335 receive_seq=4335 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999903 adj=31998656 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=46.0 th1: temp=45.1 th2: temp=46.3 th3: temp=44.3 sysload=0.39 cputime=81.914 memavail=7407000 print_time=632.829 buffer_time=2.077 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 609.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7275409 bytes_read=890509 bytes_retransmit=9 bytes_invalid=0 send_seq=127827 receive_seq=127827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=16066 freq=400015574 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4360 bytes_read=15464 bytes_retransmit=0 bytes_invalid=0 send_seq=698 receive_seq=698 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998725 adj=49996029 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37918 bytes_read=1194178 bytes_retransmit=9 bytes_invalid=0 send_seq=5027 receive_seq=5027 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000179 adj=63997622 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13452 bytes_read=82394 bytes_retransmit=9 bytes_invalid=0 send_seq=1441 receive_seq=1441 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997491 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4519 bytes_read=150676 bytes_retransmit=9 bytes_invalid=0 send_seq=704 receive_seq=704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5113 bytes_read=15194 bytes_retransmit=9 bytes_invalid=0 send_seq=699 receive_seq=699 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48189 bytes_read=424800 bytes_retransmit=0 bytes_invalid=0 send_seq=4336 receive_seq=4336 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999903 adj=31998677 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=45.7 th1: temp=45.5 th2: temp=46.5 th3: temp=44.2 sysload=0.39 cputime=82.049 memavail=7407000 print_time=633.905 buffer_time=2.153 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 610.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7287860 bytes_read=891855 bytes_retransmit=9 bytes_invalid=0 send_seq=128028 receive_seq=128028 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=17010 freq=400015598 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4366 bytes_read=15479 bytes_retransmit=0 bytes_invalid=0 send_seq=699 receive_seq=699 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998717 adj=49996132 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37987 bytes_read=1197287 bytes_retransmit=9 bytes_invalid=0 send_seq=5037 receive_seq=5037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000179 adj=63997635 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13458 bytes_read=82494 bytes_retransmit=9 bytes_invalid=0 send_seq=1442 receive_seq=1442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997502 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4525 bytes_read=150910 bytes_retransmit=9 bytes_invalid=0 send_seq=705 receive_seq=705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999523 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5119 bytes_read=15210 bytes_retransmit=9 bytes_invalid=0 send_seq=700 receive_seq=700 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48195 bytes_read=425156 bytes_retransmit=0 bytes_invalid=0 send_seq=4337 receive_seq=4337 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999902 adj=31998678 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=46.6 th1: temp=45.0 th2: temp=46.1 th3: temp=44.4 sysload=0.39 cputime=82.182 memavail=7407000 print_time=634.982 buffer_time=2.229 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 611.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7300319 bytes_read=893165 bytes_retransmit=9 bytes_invalid=0 send_seq=128229 receive_seq=128229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=17938 freq=400015603 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=4372 bytes_read=15507 bytes_retransmit=0 bytes_invalid=0 send_seq=700 receive_seq=700 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998709 adj=49996143 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38063 bytes_read=1200428 bytes_retransmit=9 bytes_invalid=0 send_seq=5048 receive_seq=5048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997593 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13464 bytes_read=82636 bytes_retransmit=9 bytes_invalid=0 send_seq=1443 receive_seq=1443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997458 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4531 bytes_read=151204 bytes_retransmit=9 bytes_invalid=0 send_seq=706 receive_seq=706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999523 adj=47997613 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5125 bytes_read=15226 bytes_retransmit=9 bytes_invalid=0 send_seq=701 receive_seq=701 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48201 bytes_read=425512 bytes_retransmit=0 bytes_invalid=0 send_seq=4338 receive_seq=4338 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999902 adj=31998646 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=46.0 th1: temp=45.2 th2: temp=46.0 th3: temp=44.4 sysload=0.36 cputime=82.317 memavail=7407036 print_time=636.058 buffer_time=2.305 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 612.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7312822 bytes_read=894539 bytes_retransmit=9 bytes_invalid=0 send_seq=128439 receive_seq=128439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=18876 freq=400015666 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=4378 bytes_read=15522 bytes_retransmit=0 bytes_invalid=0 send_seq=701 receive_seq=701 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998701 adj=49996188 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38139 bytes_read=1203542 bytes_retransmit=9 bytes_invalid=0 send_seq=5059 receive_seq=5059 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000179 adj=63997591 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13470 bytes_read=82736 bytes_retransmit=9 bytes_invalid=0 send_seq=1444 receive_seq=1444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997452 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4537 bytes_read=151438 bytes_retransmit=9 bytes_invalid=0 send_seq=707 receive_seq=707 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999523 adj=47997609 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5131 bytes_read=15253 bytes_retransmit=9 bytes_invalid=0 send_seq=702 receive_seq=702 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48207 bytes_read=425868 bytes_retransmit=0 bytes_invalid=0 send_seq=4339 receive_seq=4339 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999902 adj=31998639 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.011 th0: temp=46.2 th1: temp=44.9 th2: temp=46.1 th3: temp=44.5 sysload=0.36 cputime=82.448 memavail=7407036 print_time=637.134 buffer_time=2.381 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 613.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7325411 bytes_read=895919 bytes_retransmit=9 bytes_invalid=0 send_seq=128651 receive_seq=128650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=19787 freq=400015658 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=4384 bytes_read=15537 bytes_retransmit=0 bytes_invalid=0 send_seq=702 receive_seq=702 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998704 adj=49996132 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38215 bytes_read=1206657 bytes_retransmit=9 bytes_invalid=0 send_seq=5070 receive_seq=5070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997512 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13476 bytes_read=82836 bytes_retransmit=9 bytes_invalid=0 send_seq=1445 receive_seq=1445 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997342 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4543 bytes_read=151687 bytes_retransmit=9 bytes_invalid=0 send_seq=708 receive_seq=708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999523 adj=47997539 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5137 bytes_read=15269 bytes_retransmit=9 bytes_invalid=0 send_seq=703 receive_seq=703 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999417 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48213 bytes_read=426224 bytes_retransmit=0 bytes_invalid=0 send_seq=4340 receive_seq=4340 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999903 adj=31998589 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=46.1 th1: temp=45.0 th2: temp=46.2 th3: temp=44.5 sysload=0.36 cputime=82.584 memavail=7401744 print_time=638.211 buffer_time=2.457 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 614.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7338026 bytes_read=897304 bytes_retransmit=9 bytes_invalid=0 send_seq=128865 receive_seq=128865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=20633 freq=400015648 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=4390 bytes_read=15552 bytes_retransmit=0 bytes_invalid=0 send_seq=703 receive_seq=703 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998697 adj=49996296 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38291 bytes_read=1209859 bytes_retransmit=9 bytes_invalid=0 send_seq=5081 receive_seq=5081 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997552 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13482 bytes_read=82964 bytes_retransmit=9 bytes_invalid=0 send_seq=1446 receive_seq=1446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997380 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4549 bytes_read=151981 bytes_retransmit=9 bytes_invalid=0 send_seq=709 receive_seq=709 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997569 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5143 bytes_read=15285 bytes_retransmit=9 bytes_invalid=0 send_seq=704 receive_seq=704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48219 bytes_read=426580 bytes_retransmit=0 bytes_invalid=0 send_seq=4341 receive_seq=4341 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999903 adj=31998612 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=46.3 th1: temp=45.2 th2: temp=46.3 th3: temp=44.4 sysload=0.36 cputime=82.722 memavail=7407892 print_time=639.287 buffer_time=2.525 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 615.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=7350528 bytes_read=898714 bytes_retransmit=9 bytes_invalid=0 send_seq=129076 receive_seq=129076 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=15453 freq=400015675 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=4396 bytes_read=15568 bytes_retransmit=0 bytes_invalid=0 send_seq=704 receive_seq=704 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998689 adj=49996324 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38367 bytes_read=1212990 bytes_retransmit=9 bytes_invalid=0 send_seq=5092 receive_seq=5092 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000177 adj=63997588 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13488 bytes_read=83064 bytes_retransmit=9 bytes_invalid=0 send_seq=1447 receive_seq=1447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997419 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4555 bytes_read=152215 bytes_retransmit=9 bytes_invalid=0 send_seq=710 receive_seq=710 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999523 adj=47997605 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5149 bytes_read=15301 bytes_retransmit=9 bytes_invalid=0 send_seq=705 receive_seq=705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48225 bytes_read=426936 bytes_retransmit=0 bytes_invalid=0 send_seq=4342 receive_seq=4342 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999904 adj=31998629 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=46.2 th1: temp=45.0 th2: temp=46.4 th3: temp=44.4 sysload=0.36 cputime=82.844 memavail=7406884 print_time=639.826 buffer_time=2.063 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 616.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=7363404 bytes_read=900089 bytes_retransmit=9 bytes_invalid=0 send_seq=129289 receive_seq=129289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=16049 freq=400015692 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4402 bytes_read=15597 bytes_retransmit=0 bytes_invalid=0 send_seq=705 receive_seq=705 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998681 adj=49996191 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38443 bytes_read=1216108 bytes_retransmit=9 bytes_invalid=0 send_seq=5103 receive_seq=5103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000176 adj=63997532 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13494 bytes_read=83178 bytes_retransmit=9 bytes_invalid=0 send_seq=1448 receive_seq=1448 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997361 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4561 bytes_read=152449 bytes_retransmit=9 bytes_invalid=0 send_seq=711 receive_seq=711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999523 adj=47997562 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5155 bytes_read=15317 bytes_retransmit=9 bytes_invalid=0 send_seq=706 receive_seq=706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48231 bytes_read=427292 bytes_retransmit=0 bytes_invalid=0 send_seq=4343 receive_seq=4343 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999905 adj=31998619 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.011 th0: temp=46.1 th1: temp=45.0 th2: temp=46.2 th3: temp=44.5 sysload=0.41 cputime=82.975 memavail=7406544 print_time=640.902 buffer_time=2.140 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 617.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=7376088 bytes_read=901464 bytes_retransmit=9 bytes_invalid=0 send_seq=129502 receive_seq=129502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=16845 freq=400015712 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4408 bytes_read=15613 bytes_retransmit=0 bytes_invalid=0 send_seq=706 receive_seq=706 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998673 adj=49996134 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38519 bytes_read=1219252 bytes_retransmit=9 bytes_invalid=0 send_seq=5114 receive_seq=5114 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997502 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13500 bytes_read=83306 bytes_retransmit=9 bytes_invalid=0 send_seq=1449 receive_seq=1449 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997352 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4567 bytes_read=152743 bytes_retransmit=9 bytes_invalid=0 send_seq=712 receive_seq=712 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999523 adj=47997548 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5161 bytes_read=15344 bytes_retransmit=9 bytes_invalid=0 send_seq=707 receive_seq=707 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48237 bytes_read=427648 bytes_retransmit=0 bytes_invalid=0 send_seq=4344 receive_seq=4344 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999905 adj=31998618 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=45.9 th1: temp=45.2 th2: temp=45.9 th3: temp=44.4 sysload=0.41 cputime=83.108 memavail=7406648 print_time=641.979 buffer_time=2.216 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 618.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=7388600 bytes_read=902868 bytes_retransmit=9 bytes_invalid=0 send_seq=129715 receive_seq=129715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=17773 freq=400015709 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4414 bytes_read=15629 bytes_retransmit=0 bytes_invalid=0 send_seq=707 receive_seq=707 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998666 adj=49996146 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38595 bytes_read=1222367 bytes_retransmit=9 bytes_invalid=0 send_seq=5125 receive_seq=5125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997487 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13506 bytes_read=83406 bytes_retransmit=9 bytes_invalid=0 send_seq=1450 receive_seq=1450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997340 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4573 bytes_read=152992 bytes_retransmit=9 bytes_invalid=0 send_seq=713 receive_seq=713 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999523 adj=47997535 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5167 bytes_read=15360 bytes_retransmit=9 bytes_invalid=0 send_seq=708 receive_seq=708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999419 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48243 bytes_read=428004 bytes_retransmit=0 bytes_invalid=0 send_seq=4345 receive_seq=4345 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999904 adj=31998604 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=46.1 th1: temp=45.4 th2: temp=46.2 th3: temp=44.4 sysload=0.41 cputime=83.240 memavail=7406648 print_time=643.055 buffer_time=2.292 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 619.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=7401171 bytes_read=904238 bytes_retransmit=9 bytes_invalid=0 send_seq=129927 receive_seq=129927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=18694 freq=400015707 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4420 bytes_read=15645 bytes_retransmit=0 bytes_invalid=0 send_seq=708 receive_seq=708 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998660 adj=49996197 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38671 bytes_read=1225482 bytes_retransmit=9 bytes_invalid=0 send_seq=5136 receive_seq=5136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997589 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13512 bytes_read=83506 bytes_retransmit=9 bytes_invalid=0 send_seq=1451 receive_seq=1451 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997373 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4579 bytes_read=153226 bytes_retransmit=9 bytes_invalid=0 send_seq=714 receive_seq=714 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997559 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5173 bytes_read=15376 bytes_retransmit=9 bytes_invalid=0 send_seq=709 receive_seq=709 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48249 bytes_read=428360 bytes_retransmit=0 bytes_invalid=0 send_seq=4346 receive_seq=4346 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999904 adj=31998611 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=46.3 th1: temp=45.1 th2: temp=46.3 th3: temp=44.4 sysload=0.41 cputime=83.370 memavail=7406648 print_time=644.131 buffer_time=2.368 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 620.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7413671 bytes_read=905619 bytes_retransmit=9 bytes_invalid=0 send_seq=130138 receive_seq=130138 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=19622 freq=400015701 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4426 bytes_read=15661 bytes_retransmit=0 bytes_invalid=0 send_seq=709 receive_seq=709 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998653 adj=49996232 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38747 bytes_read=1228641 bytes_retransmit=9 bytes_invalid=0 send_seq=5147 receive_seq=5147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997687 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13518 bytes_read=83634 bytes_retransmit=9 bytes_invalid=0 send_seq=1452 receive_seq=1452 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000002 adj=63997393 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4585 bytes_read=153520 bytes_retransmit=9 bytes_invalid=0 send_seq=715 receive_seq=715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997597 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5179 bytes_read=15392 bytes_retransmit=9 bytes_invalid=0 send_seq=710 receive_seq=710 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48255 bytes_read=428716 bytes_retransmit=0 bytes_invalid=0 send_seq=4347 receive_seq=4347 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999904 adj=31998613 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=46.2 th1: temp=45.3 th2: temp=46.2 th3: temp=44.6 sysload=0.41 cputime=83.501 memavail=7406648 print_time=645.208 buffer_time=2.444 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 621.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7426246 bytes_read=907028 bytes_retransmit=9 bytes_invalid=0 send_seq=130352 receive_seq=130352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=20550 freq=400015679 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4432 bytes_read=15690 bytes_retransmit=0 bytes_invalid=0 send_seq=710 receive_seq=710 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998647 adj=49996264 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38823 bytes_read=1231754 bytes_retransmit=9 bytes_invalid=0 send_seq=5158 receive_seq=5158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997766 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13524 bytes_read=83748 bytes_retransmit=9 bytes_invalid=0 send_seq=1453 receive_seq=1453 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000002 adj=63997418 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4591 bytes_read=153754 bytes_retransmit=9 bytes_invalid=0 send_seq=716 receive_seq=716 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997609 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5185 bytes_read=15408 bytes_retransmit=9 bytes_invalid=0 send_seq=711 receive_seq=711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48261 bytes_read=429072 bytes_retransmit=0 bytes_invalid=0 send_seq=4348 receive_seq=4348 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999903 adj=31998633 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=46.2 th1: temp=44.8 th2: temp=46.4 th3: temp=44.5 sysload=0.38 cputime=83.630 memavail=7406648 print_time=646.284 buffer_time=2.520 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 622.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7438738 bytes_read=908388 bytes_retransmit=9 bytes_invalid=0 send_seq=130563 receive_seq=130563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=15370 freq=400015673 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4438 bytes_read=15706 bytes_retransmit=0 bytes_invalid=0 send_seq=711 receive_seq=711 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998641 adj=49996312 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38892 bytes_read=1234902 bytes_retransmit=9 bytes_invalid=0 send_seq=5168 receive_seq=5168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997762 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13530 bytes_read=83848 bytes_retransmit=9 bytes_invalid=0 send_seq=1454 receive_seq=1454 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000002 adj=63997470 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4597 bytes_read=153988 bytes_retransmit=9 bytes_invalid=0 send_seq=717 receive_seq=717 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5191 bytes_read=15435 bytes_retransmit=9 bytes_invalid=0 send_seq=712 receive_seq=712 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48267 bytes_read=429428 bytes_retransmit=0 bytes_invalid=0 send_seq=4349 receive_seq=4349 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999903 adj=31998644 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=46.2 th1: temp=45.4 th2: temp=46.5 th3: temp=44.7 sysload=0.38 cputime=83.746 memavail=7406648 print_time=646.823 buffer_time=2.057 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 623.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7451550 bytes_read=909773 bytes_retransmit=9 bytes_invalid=0 send_seq=130778 receive_seq=130778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=16049 freq=400015657 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4444 bytes_read=15722 bytes_retransmit=0 bytes_invalid=0 send_seq=712 receive_seq=712 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998636 adj=49996259 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38968 bytes_read=1238043 bytes_retransmit=9 bytes_invalid=0 send_seq=5179 receive_seq=5179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997756 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13536 bytes_read=83976 bytes_retransmit=9 bytes_invalid=0 send_seq=1455 receive_seq=1455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997475 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4603 bytes_read=154297 bytes_retransmit=9 bytes_invalid=0 send_seq=718 receive_seq=718 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5197 bytes_read=15451 bytes_retransmit=9 bytes_invalid=0 send_seq=713 receive_seq=713 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48273 bytes_read=429784 bytes_retransmit=0 bytes_invalid=0 send_seq=4350 receive_seq=4350 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999902 adj=31998644 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=46.4 th1: temp=45.3 th2: temp=46.3 th3: temp=44.6 sysload=0.38 cputime=83.880 memavail=7406648 print_time=647.899 buffer_time=2.134 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 624.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7464294 bytes_read=911187 bytes_retransmit=9 bytes_invalid=0 send_seq=130993 receive_seq=130993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=26 upcoming_bytes=16778 freq=400015653 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4450 bytes_read=15738 bytes_retransmit=0 bytes_invalid=0 send_seq=713 receive_seq=713 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998629 adj=49996268 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=39044 bytes_read=1241156 bytes_retransmit=9 bytes_invalid=0 send_seq=5190 receive_seq=5190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997788 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13542 bytes_read=84076 bytes_retransmit=9 bytes_invalid=0 send_seq=1456 receive_seq=1456 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997535 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4609 bytes_read=154531 bytes_retransmit=9 bytes_invalid=0 send_seq=719 receive_seq=719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997679 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5203 bytes_read=15467 bytes_retransmit=9 bytes_invalid=0 send_seq=714 receive_seq=714 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48279 bytes_read=430140 bytes_retransmit=0 bytes_invalid=0 send_seq=4351 receive_seq=4351 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999902 adj=31998650 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.011 th0: temp=46.6 th1: temp=45.3 th2: temp=46.4 th3: temp=44.4 sysload=0.38 cputime=84.013 memavail=7406648 print_time=648.976 buffer_time=2.210 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
webhooks client 3916698168: Disconnected
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
LIS2DW finished 'toolboard_t0' measurements
Stats 625.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7476820 bytes_read=912568 bytes_retransmit=9 bytes_invalid=0 send_seq=131204 receive_seq=131204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=11615 freq=400015656 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4456 bytes_read=15754 bytes_retransmit=0 bytes_invalid=0 send_seq=714 receive_seq=714 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998626 adj=49996290 toolboard_t0: mcu_awake=0.283 mcu_task_avg=0.000117 mcu_task_stddev=0.000069 bytes_write=39119 bytes_read=1241980 bytes_retransmit=9 bytes_invalid=0 send_seq=5199 receive_seq=5199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997744 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13548 bytes_read=84176 bytes_retransmit=9 bytes_invalid=0 send_seq=1457 receive_seq=1457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997536 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4615 bytes_read=154780 bytes_retransmit=9 bytes_invalid=0 send_seq=720 receive_seq=720 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5209 bytes_read=15483 bytes_retransmit=9 bytes_invalid=0 send_seq=715 receive_seq=715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48285 bytes_read=430496 bytes_retransmit=0 bytes_invalid=0 send_seq=4352 receive_seq=4352 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999902 adj=31998654 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=46.1 th1: temp=45.4 th2: temp=46.4 th3: temp=44.5 sysload=0.38 cputime=84.115 memavail=7405832 print_time=649.514 buffer_time=1.748 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 626.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7489343 bytes_read=913938 bytes_retransmit=9 bytes_invalid=0 send_seq=131416 receive_seq=131416 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=320 freq=400015701 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4462 bytes_read=15783 bytes_retransmit=0 bytes_invalid=0 send_seq=715 receive_seq=715 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998622 adj=49996243 toolboard_t0: mcu_awake=0.283 mcu_task_avg=0.000117 mcu_task_stddev=0.000069 bytes_write=39125 bytes_read=1242108 bytes_retransmit=9 bytes_invalid=0 send_seq=5200 receive_seq=5200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997725 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13554 bytes_read=84318 bytes_retransmit=9 bytes_invalid=0 send_seq=1458 receive_seq=1458 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997530 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4621 bytes_read=155059 bytes_retransmit=9 bytes_invalid=0 send_seq=721 receive_seq=721 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5215 bytes_read=15499 bytes_retransmit=9 bytes_invalid=0 send_seq=716 receive_seq=716 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48291 bytes_read=430852 bytes_retransmit=0 bytes_invalid=0 send_seq=4353 receive_seq=4353 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998647 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.2 th2: temp=46.4 th3: temp=44.9 sysload=0.35 cputime=84.188 memavail=7405952 print_time=649.514 buffer_time=0.748 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 627.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7490010 bytes_read=914417 bytes_retransmit=9 bytes_invalid=0 send_seq=131444 receive_seq=131444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015706 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4468 bytes_read=15799 bytes_retransmit=0 bytes_invalid=0 send_seq=716 receive_seq=716 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998617 adj=49996113 toolboard_t0: mcu_awake=0.283 mcu_task_avg=0.000117 mcu_task_stddev=0.000069 bytes_write=39131 bytes_read=1242208 bytes_retransmit=9 bytes_invalid=0 send_seq=5201 receive_seq=5201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997615 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13560 bytes_read=84418 bytes_retransmit=9 bytes_invalid=0 send_seq=1459 receive_seq=1459 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997455 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4627 bytes_read=155293 bytes_retransmit=9 bytes_invalid=0 send_seq=722 receive_seq=722 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997603 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5221 bytes_read=15526 bytes_retransmit=9 bytes_invalid=0 send_seq=717 receive_seq=717 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=25.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48297 bytes_read=431208 bytes_retransmit=0 bytes_invalid=0 send_seq=4354 receive_seq=4354 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998593 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.011 th0: temp=46.2 th1: temp=45.1 th2: temp=46.6 th3: temp=44.7 sysload=0.35 cputime=84.236 memavail=7405952 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 628.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7490308 bytes_read=914842 bytes_retransmit=9 bytes_invalid=0 send_seq=131467 receive_seq=131467 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015711 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4474 bytes_read=15815 bytes_retransmit=0 bytes_invalid=0 send_seq=717 receive_seq=717 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998613 adj=49996043 toolboard_t0: mcu_awake=0.283 mcu_task_avg=0.000117 mcu_task_stddev=0.000069 bytes_write=39137 bytes_read=1242308 bytes_retransmit=9 bytes_invalid=0 send_seq=5202 receive_seq=5202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997666 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13566 bytes_read=84518 bytes_retransmit=9 bytes_invalid=0 send_seq=1460 receive_seq=1460 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63997440 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4633 bytes_read=155557 bytes_retransmit=9 bytes_invalid=0 send_seq=723 receive_seq=723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997591 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5227 bytes_read=15542 bytes_retransmit=9 bytes_invalid=0 send_seq=718 receive_seq=718 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48303 bytes_read=431558 bytes_retransmit=0 bytes_invalid=0 send_seq=4355 receive_seq=4355 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999903 adj=31998586 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=46.3 th1: temp=45.3 th2: temp=46.4 th3: temp=44.6 sysload=0.35 cputime=84.281 memavail=7406212 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 629.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7490601 bytes_read=915262 bytes_retransmit=9 bytes_invalid=0 send_seq=131489 receive_seq=131489 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015732 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4480 bytes_read=15831 bytes_retransmit=0 bytes_invalid=0 send_seq=718 receive_seq=718 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998609 adj=49995995 toolboard_t0: mcu_awake=0.283 mcu_task_avg=0.000117 mcu_task_stddev=0.000069 bytes_write=39143 bytes_read=1242436 bytes_retransmit=9 bytes_invalid=0 send_seq=5203 receive_seq=5203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997749 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13572 bytes_read=84646 bytes_retransmit=9 bytes_invalid=0 send_seq=1461 receive_seq=1461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997424 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4639 bytes_read=155836 bytes_retransmit=9 bytes_invalid=0 send_seq=724 receive_seq=724 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997581 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5233 bytes_read=15558 bytes_retransmit=9 bytes_invalid=0 send_seq=719 receive_seq=719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48309 bytes_read=431887 bytes_retransmit=0 bytes_invalid=0 send_seq=4356 receive_seq=4356 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999903 adj=31998611 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=46.4 th1: temp=44.8 th2: temp=46.4 th3: temp=44.5 sysload=0.35 cputime=84.329 memavail=7406972 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 630.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=7490849 bytes_read=915682 bytes_retransmit=9 bytes_invalid=0 send_seq=131502 receive_seq=131502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015707 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4486 bytes_read=15847 bytes_retransmit=0 bytes_invalid=0 send_seq=719 receive_seq=719 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998605 adj=49996067 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39149 bytes_read=1242550 bytes_retransmit=9 bytes_invalid=0 send_seq=5204 receive_seq=5204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997680 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13578 bytes_read=84746 bytes_retransmit=9 bytes_invalid=0 send_seq=1462 receive_seq=1462 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000008 adj=63997425 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4645 bytes_read=156070 bytes_retransmit=9 bytes_invalid=0 send_seq=725 receive_seq=725 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999523 adj=47997553 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5239 bytes_read=15574 bytes_retransmit=9 bytes_invalid=0 send_seq=720 receive_seq=720 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48315 bytes_read=432232 bytes_retransmit=0 bytes_invalid=0 send_seq=4357 receive_seq=4357 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999903 adj=31998593 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=46.5 th1: temp=45.6 th2: temp=46.3 th3: temp=44.6 sysload=0.35 cputime=84.372 memavail=7406112 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 631.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=7491147 bytes_read=916107 bytes_retransmit=9 bytes_invalid=0 send_seq=131525 receive_seq=131525 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015687 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4492 bytes_read=15876 bytes_retransmit=0 bytes_invalid=0 send_seq=720 receive_seq=720 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998602 adj=49996190 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39155 bytes_read=1242650 bytes_retransmit=9 bytes_invalid=0 send_seq=5205 receive_seq=5205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997707 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13584 bytes_read=84860 bytes_retransmit=9 bytes_invalid=0 send_seq=1463 receive_seq=1463 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997515 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4651 bytes_read=156319 bytes_retransmit=9 bytes_invalid=0 send_seq=726 receive_seq=726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997614 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5245 bytes_read=15590 bytes_retransmit=9 bytes_invalid=0 send_seq=721 receive_seq=721 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48321 bytes_read=432577 bytes_retransmit=0 bytes_invalid=0 send_seq=4358 receive_seq=4358 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999903 adj=31998644 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=46.1 th1: temp=45.3 th2: temp=46.4 th3: temp=44.6 sysload=0.32 cputime=84.420 memavail=7408588 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 632.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=7491445 bytes_read=916530 bytes_retransmit=9 bytes_invalid=0 send_seq=131548 receive_seq=131548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015669 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4498 bytes_read=15892 bytes_retransmit=0 bytes_invalid=0 send_seq=721 receive_seq=721 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998598 adj=49996297 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39161 bytes_read=1242778 bytes_retransmit=9 bytes_invalid=0 send_seq=5206 receive_seq=5206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997778 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13590 bytes_read=84988 bytes_retransmit=9 bytes_invalid=0 send_seq=1464 receive_seq=1464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997550 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4657 bytes_read=156598 bytes_retransmit=9 bytes_invalid=0 send_seq=727 receive_seq=727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997749 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5251 bytes_read=15617 bytes_retransmit=9 bytes_invalid=0 send_seq=722 receive_seq=722 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48327 bytes_read=432922 bytes_retransmit=0 bytes_invalid=0 send_seq=4359 receive_seq=4359 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999902 adj=31998661 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=46.5 th1: temp=45.5 th2: temp=46.3 th3: temp=44.6 sysload=0.32 cputime=84.464 memavail=7408588 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 633.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=7491743 bytes_read=916979 bytes_retransmit=9 bytes_invalid=0 send_seq=131571 receive_seq=131571 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015653 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4504 bytes_read=15908 bytes_retransmit=0 bytes_invalid=0 send_seq=722 receive_seq=722 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998594 adj=49996356 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39167 bytes_read=1242878 bytes_retransmit=9 bytes_invalid=0 send_seq=5207 receive_seq=5207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997760 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13596 bytes_read=85088 bytes_retransmit=9 bytes_invalid=0 send_seq=1465 receive_seq=1465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997570 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4663 bytes_read=156847 bytes_retransmit=9 bytes_invalid=0 send_seq=728 receive_seq=728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997747 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5257 bytes_read=15633 bytes_retransmit=9 bytes_invalid=0 send_seq=723 receive_seq=723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48333 bytes_read=433267 bytes_retransmit=0 bytes_invalid=0 send_seq=4360 receive_seq=4360 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998669 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=46.7 th1: temp=45.3 th2: temp=46.4 th3: temp=44.9 sysload=0.32 cputime=84.508 memavail=7408588 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 634.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=7492041 bytes_read=917404 bytes_retransmit=9 bytes_invalid=0 send_seq=131594 receive_seq=131594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015645 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4510 bytes_read=15924 bytes_retransmit=0 bytes_invalid=0 send_seq=723 receive_seq=723 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998591 adj=49996403 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39173 bytes_read=1242978 bytes_retransmit=9 bytes_invalid=0 send_seq=5208 receive_seq=5208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997766 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13602 bytes_read=85188 bytes_retransmit=9 bytes_invalid=0 send_seq=1466 receive_seq=1466 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997634 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4669 bytes_read=157096 bytes_retransmit=9 bytes_invalid=0 send_seq=729 receive_seq=729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997742 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5263 bytes_read=15649 bytes_retransmit=9 bytes_invalid=0 send_seq=724 receive_seq=724 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48339 bytes_read=433612 bytes_retransmit=0 bytes_invalid=0 send_seq=4361 receive_seq=4361 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998676 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=46.1 th1: temp=45.7 th2: temp=46.2 th3: temp=44.7 sysload=0.32 cputime=84.552 memavail=7408592 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 635.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000007 bytes_write=7492339 bytes_read=917844 bytes_retransmit=9 bytes_invalid=0 send_seq=131617 receive_seq=131617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015631 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4516 bytes_read=15940 bytes_retransmit=0 bytes_invalid=0 send_seq=724 receive_seq=724 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998588 adj=49996425 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=39179 bytes_read=1243120 bytes_retransmit=9 bytes_invalid=0 send_seq=5209 receive_seq=5209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997738 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13608 bytes_read=85316 bytes_retransmit=9 bytes_invalid=0 send_seq=1467 receive_seq=1467 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997630 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4675 bytes_read=157375 bytes_retransmit=9 bytes_invalid=0 send_seq=730 receive_seq=730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997728 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5269 bytes_read=15665 bytes_retransmit=9 bytes_invalid=0 send_seq=725 receive_seq=725 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48345 bytes_read=433957 bytes_retransmit=0 bytes_invalid=0 send_seq=4362 receive_seq=4362 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998671 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=46.6 th1: temp=45.7 th2: temp=46.0 th3: temp=44.8 sysload=0.32 cputime=84.598 memavail=7408140 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 636.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000007 bytes_write=7492637 bytes_read=918298 bytes_retransmit=9 bytes_invalid=0 send_seq=131640 receive_seq=131640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015620 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4522 bytes_read=15969 bytes_retransmit=0 bytes_invalid=0 send_seq=725 receive_seq=725 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998586 adj=49996459 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=39185 bytes_read=1243220 bytes_retransmit=9 bytes_invalid=0 send_seq=5210 receive_seq=5210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997730 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13614 bytes_read=85430 bytes_retransmit=9 bytes_invalid=0 send_seq=1468 receive_seq=1468 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000008 adj=63997624 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4681 bytes_read=157609 bytes_retransmit=9 bytes_invalid=0 send_seq=731 receive_seq=731 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997728 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5275 bytes_read=15681 bytes_retransmit=9 bytes_invalid=0 send_seq=726 receive_seq=726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999467 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48351 bytes_read=434303 bytes_retransmit=0 bytes_invalid=0 send_seq=4363 receive_seq=4363 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998684 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=46.5 th1: temp=45.6 th2: temp=46.8 th3: temp=44.5 sysload=0.29 cputime=84.642 memavail=7408140 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 637.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000007 bytes_write=7492935 bytes_read=918723 bytes_retransmit=9 bytes_invalid=0 send_seq=131663 receive_seq=131663 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015608 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4528 bytes_read=15985 bytes_retransmit=0 bytes_invalid=0 send_seq=726 receive_seq=726 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998582 adj=49996487 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=39191 bytes_read=1243320 bytes_retransmit=9 bytes_invalid=0 send_seq=5211 receive_seq=5211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997782 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13620 bytes_read=85530 bytes_retransmit=9 bytes_invalid=0 send_seq=1469 receive_seq=1469 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000008 adj=63997610 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4687 bytes_read=157858 bytes_retransmit=9 bytes_invalid=0 send_seq=732 receive_seq=732 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997758 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5281 bytes_read=15708 bytes_retransmit=9 bytes_invalid=0 send_seq=727 receive_seq=727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999470 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48357 bytes_read=434659 bytes_retransmit=0 bytes_invalid=0 send_seq=4364 receive_seq=4364 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998684 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=46.7 th1: temp=45.6 th2: temp=46.4 th3: temp=44.8 sysload=0.29 cputime=84.687 memavail=7408140 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 638.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000007 bytes_write=7493233 bytes_read=919148 bytes_retransmit=9 bytes_invalid=0 send_seq=131686 receive_seq=131686 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015595 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4534 bytes_read=16001 bytes_retransmit=0 bytes_invalid=0 send_seq=727 receive_seq=727 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998580 adj=49996488 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=39197 bytes_read=1243448 bytes_retransmit=9 bytes_invalid=0 send_seq=5212 receive_seq=5212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997839 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13626 bytes_read=85658 bytes_retransmit=9 bytes_invalid=0 send_seq=1470 receive_seq=1470 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997621 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4693 bytes_read=158152 bytes_retransmit=9 bytes_invalid=0 send_seq=733 receive_seq=733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997742 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5287 bytes_read=15724 bytes_retransmit=9 bytes_invalid=0 send_seq=728 receive_seq=728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999470 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48363 bytes_read=435015 bytes_retransmit=0 bytes_invalid=0 send_seq=4365 receive_seq=4365 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999899 adj=31998681 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=46.8 th1: temp=45.6 th2: temp=46.4 th3: temp=44.7 sysload=0.29 cputime=84.732 memavail=7408140 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 639.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000007 bytes_write=7493531 bytes_read=919602 bytes_retransmit=9 bytes_invalid=0 send_seq=131709 receive_seq=131709 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015586 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4540 bytes_read=16017 bytes_retransmit=0 bytes_invalid=0 send_seq=728 receive_seq=728 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998578 adj=49996514 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=39203 bytes_read=1243548 bytes_retransmit=9 bytes_invalid=0 send_seq=5213 receive_seq=5213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997814 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13632 bytes_read=85758 bytes_retransmit=9 bytes_invalid=0 send_seq=1471 receive_seq=1471 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000008 adj=63997631 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4699 bytes_read=158386 bytes_retransmit=9 bytes_invalid=0 send_seq=734 receive_seq=734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997735 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5293 bytes_read=15740 bytes_retransmit=9 bytes_invalid=0 send_seq=729 receive_seq=729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999467 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48369 bytes_read=435371 bytes_retransmit=0 bytes_invalid=0 send_seq=4366 receive_seq=4366 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999899 adj=31998681 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=46.4 th1: temp=45.6 th2: temp=46.3 th3: temp=44.8 sysload=0.29 cputime=84.776 memavail=7408140 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 640.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7493829 bytes_read=920042 bytes_retransmit=9 bytes_invalid=0 send_seq=131732 receive_seq=131732 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015578 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4546 bytes_read=16033 bytes_retransmit=0 bytes_invalid=0 send_seq=729 receive_seq=729 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998577 adj=49996542 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39209 bytes_read=1243662 bytes_retransmit=9 bytes_invalid=0 send_seq=5214 receive_seq=5214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997776 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13638 bytes_read=85858 bytes_retransmit=9 bytes_invalid=0 send_seq=1472 receive_seq=1472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997614 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4705 bytes_read=158635 bytes_retransmit=9 bytes_invalid=0 send_seq=735 receive_seq=735 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997722 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5299 bytes_read=15756 bytes_retransmit=9 bytes_invalid=0 send_seq=730 receive_seq=730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999466 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48375 bytes_read=435727 bytes_retransmit=0 bytes_invalid=0 send_seq=4367 receive_seq=4367 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998680 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=46.5 th1: temp=45.4 th2: temp=46.8 th3: temp=44.5 sysload=0.29 cputime=84.822 memavail=7408156 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 641.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7494127 bytes_read=920467 bytes_retransmit=9 bytes_invalid=0 send_seq=131755 receive_seq=131755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015578 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4552 bytes_read=16062 bytes_retransmit=0 bytes_invalid=0 send_seq=730 receive_seq=730 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998575 adj=49996554 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39215 bytes_read=1243790 bytes_retransmit=9 bytes_invalid=0 send_seq=5215 receive_seq=5215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997761 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13644 bytes_read=86000 bytes_retransmit=9 bytes_invalid=0 send_seq=1473 receive_seq=1473 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997600 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4711 bytes_read=158914 bytes_retransmit=9 bytes_invalid=0 send_seq=736 receive_seq=736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997732 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5305 bytes_read=15772 bytes_retransmit=9 bytes_invalid=0 send_seq=731 receive_seq=731 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48381 bytes_read=436083 bytes_retransmit=0 bytes_invalid=0 send_seq=4368 receive_seq=4368 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998694 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=46.2 th1: temp=45.9 th2: temp=46.7 th3: temp=44.7 sysload=0.27 cputime=84.867 memavail=7408156 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 642.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7494425 bytes_read=920921 bytes_retransmit=9 bytes_invalid=0 send_seq=131778 receive_seq=131778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015568 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4558 bytes_read=16078 bytes_retransmit=0 bytes_invalid=0 send_seq=731 receive_seq=731 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998573 adj=49996541 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39221 bytes_read=1243890 bytes_retransmit=9 bytes_invalid=0 send_seq=5216 receive_seq=5216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997715 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13650 bytes_read=86100 bytes_retransmit=9 bytes_invalid=0 send_seq=1474 receive_seq=1474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997571 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4717 bytes_read=159148 bytes_retransmit=9 bytes_invalid=0 send_seq=737 receive_seq=737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997718 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5311 bytes_read=15799 bytes_retransmit=9 bytes_invalid=0 send_seq=732 receive_seq=732 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48387 bytes_read=436439 bytes_retransmit=0 bytes_invalid=0 send_seq=4369 receive_seq=4369 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998687 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=46.8 th1: temp=45.4 th2: temp=46.2 th3: temp=44.7 sysload=0.27 cputime=84.912 memavail=7408156 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 643.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7494723 bytes_read=921342 bytes_retransmit=9 bytes_invalid=0 send_seq=131801 receive_seq=131801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015555 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4564 bytes_read=16094 bytes_retransmit=0 bytes_invalid=0 send_seq=732 receive_seq=732 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998571 adj=49996556 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39227 bytes_read=1243990 bytes_retransmit=9 bytes_invalid=0 send_seq=5217 receive_seq=5217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997704 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13656 bytes_read=86200 bytes_retransmit=9 bytes_invalid=0 send_seq=1475 receive_seq=1475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997590 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4723 bytes_read=159412 bytes_retransmit=9 bytes_invalid=0 send_seq=738 receive_seq=738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997719 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5317 bytes_read=15815 bytes_retransmit=9 bytes_invalid=0 send_seq=733 receive_seq=733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48393 bytes_read=436795 bytes_retransmit=0 bytes_invalid=0 send_seq=4370 receive_seq=4370 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999899 adj=31998685 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.5 th2: temp=46.4 th3: temp=45.1 sysload=0.27 cputime=84.954 memavail=7408156 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 644.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7495021 bytes_read=921766 bytes_retransmit=9 bytes_invalid=0 send_seq=131824 receive_seq=131824 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015558 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4570 bytes_read=16110 bytes_retransmit=0 bytes_invalid=0 send_seq=733 receive_seq=733 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998569 adj=49996579 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39233 bytes_read=1244118 bytes_retransmit=9 bytes_invalid=0 send_seq=5218 receive_seq=5218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997725 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13662 bytes_read=86328 bytes_retransmit=9 bytes_invalid=0 send_seq=1476 receive_seq=1476 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000008 adj=63997615 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4729 bytes_read=159691 bytes_retransmit=9 bytes_invalid=0 send_seq=739 receive_seq=739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997749 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5323 bytes_read=15831 bytes_retransmit=9 bytes_invalid=0 send_seq=734 receive_seq=734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999469 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=24.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48399 bytes_read=437151 bytes_retransmit=0 bytes_invalid=0 send_seq=4371 receive_seq=4371 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999899 adj=31998700 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.9 th2: temp=46.6 th3: temp=44.8 sysload=0.27 cputime=84.999 memavail=7408156 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 645.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7495319 bytes_read=922235 bytes_retransmit=9 bytes_invalid=0 send_seq=131847 receive_seq=131847 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015549 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4576 bytes_read=16126 bytes_retransmit=0 bytes_invalid=0 send_seq=734 receive_seq=734 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998569 adj=49996563 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39239 bytes_read=1244218 bytes_retransmit=9 bytes_invalid=0 send_seq=5219 receive_seq=5219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997689 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13668 bytes_read=86428 bytes_retransmit=9 bytes_invalid=0 send_seq=1477 receive_seq=1477 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997605 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4735 bytes_read=159925 bytes_retransmit=9 bytes_invalid=0 send_seq=740 receive_seq=740 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997731 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5329 bytes_read=15847 bytes_retransmit=9 bytes_invalid=0 send_seq=735 receive_seq=735 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48405 bytes_read=437507 bytes_retransmit=0 bytes_invalid=0 send_seq=4372 receive_seq=4372 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998681 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=46.9 th1: temp=46.0 th2: temp=46.8 th3: temp=44.9 sysload=0.27 cputime=85.043 memavail=7408188 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 646.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7495617 bytes_read=922660 bytes_retransmit=9 bytes_invalid=0 send_seq=131870 receive_seq=131870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015551 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4582 bytes_read=16155 bytes_retransmit=0 bytes_invalid=0 send_seq=735 receive_seq=735 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998569 adj=49996596 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39245 bytes_read=1244332 bytes_retransmit=9 bytes_invalid=0 send_seq=5220 receive_seq=5220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000181 adj=63997702 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13674 bytes_read=86542 bytes_retransmit=9 bytes_invalid=0 send_seq=1478 receive_seq=1478 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000034 adj=63997849 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4741 bytes_read=160174 bytes_retransmit=9 bytes_invalid=0 send_seq=741 receive_seq=741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997755 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5335 bytes_read=15863 bytes_retransmit=9 bytes_invalid=0 send_seq=736 receive_seq=736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999477 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48411 bytes_read=437863 bytes_retransmit=0 bytes_invalid=0 send_seq=4373 receive_seq=4373 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998716 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.8 th2: temp=46.5 th3: temp=44.8 sysload=0.25 cputime=85.085 memavail=7408188 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 647.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7495915 bytes_read=923085 bytes_retransmit=9 bytes_invalid=0 send_seq=131893 receive_seq=131893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015546 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4588 bytes_read=16171 bytes_retransmit=0 bytes_invalid=0 send_seq=736 receive_seq=736 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998568 adj=49996591 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39251 bytes_read=1244456 bytes_retransmit=9 bytes_invalid=0 send_seq=5221 receive_seq=5221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997683 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13680 bytes_read=86666 bytes_retransmit=9 bytes_invalid=0 send_seq=1479 receive_seq=1479 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997920 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4747 bytes_read=160453 bytes_retransmit=9 bytes_invalid=0 send_seq=742 receive_seq=742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997721 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5341 bytes_read=15890 bytes_retransmit=9 bytes_invalid=0 send_seq=737 receive_seq=737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999466 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48417 bytes_read=438219 bytes_retransmit=0 bytes_invalid=0 send_seq=4374 receive_seq=4374 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998703 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=47.0 th1: temp=45.8 th2: temp=46.6 th3: temp=44.9 sysload=0.25 cputime=85.128 memavail=7408188 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 648.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7496213 bytes_read=923539 bytes_retransmit=9 bytes_invalid=0 send_seq=131916 receive_seq=131916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015552 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4594 bytes_read=16187 bytes_retransmit=0 bytes_invalid=0 send_seq=737 receive_seq=737 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998569 adj=49996600 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39257 bytes_read=1244549 bytes_retransmit=9 bytes_invalid=0 send_seq=5222 receive_seq=5222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997680 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13686 bytes_read=86759 bytes_retransmit=9 bytes_invalid=0 send_seq=1480 receive_seq=1480 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997803 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4753 bytes_read=160702 bytes_retransmit=9 bytes_invalid=0 send_seq=743 receive_seq=743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997706 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5347 bytes_read=15906 bytes_retransmit=9 bytes_invalid=0 send_seq=738 receive_seq=738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999462 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48423 bytes_read=438575 bytes_retransmit=0 bytes_invalid=0 send_seq=4375 receive_seq=4375 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998687 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=46.6 th1: temp=45.9 th2: temp=46.7 th3: temp=44.9 sysload=0.25 cputime=85.176 memavail=7409056 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 649.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7496511 bytes_read=923964 bytes_retransmit=9 bytes_invalid=0 send_seq=131939 receive_seq=131939 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015541 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4600 bytes_read=16203 bytes_retransmit=0 bytes_invalid=0 send_seq=738 receive_seq=738 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998570 adj=49996611 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39263 bytes_read=1244642 bytes_retransmit=9 bytes_invalid=0 send_seq=5223 receive_seq=5223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997649 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13692 bytes_read=86852 bytes_retransmit=9 bytes_invalid=0 send_seq=1481 receive_seq=1481 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997711 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4759 bytes_read=160966 bytes_retransmit=9 bytes_invalid=0 send_seq=744 receive_seq=744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5353 bytes_read=15922 bytes_retransmit=9 bytes_invalid=0 send_seq=739 receive_seq=739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999456 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48429 bytes_read=438931 bytes_retransmit=0 bytes_invalid=0 send_seq=4376 receive_seq=4376 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998664 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.8 th2: temp=46.7 th3: temp=44.9 sysload=0.25 cputime=85.218 memavail=7409056 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 650.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=7496809 bytes_read=924404 bytes_retransmit=9 bytes_invalid=0 send_seq=131962 receive_seq=131962 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015544 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4606 bytes_read=16219 bytes_retransmit=0 bytes_invalid=0 send_seq=739 receive_seq=739 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998568 adj=49996641 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39269 bytes_read=1244761 bytes_retransmit=9 bytes_invalid=0 send_seq=5224 receive_seq=5224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000177 adj=63997678 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13698 bytes_read=86971 bytes_retransmit=9 bytes_invalid=0 send_seq=1482 receive_seq=1482 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997659 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4765 bytes_read=161230 bytes_retransmit=9 bytes_invalid=0 send_seq=745 receive_seq=745 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5359 bytes_read=15938 bytes_retransmit=9 bytes_invalid=0 send_seq=740 receive_seq=740 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999459 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48435 bytes_read=439287 bytes_retransmit=0 bytes_invalid=0 send_seq=4377 receive_seq=4377 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998668 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=46.8 th1: temp=45.9 th2: temp=46.6 th3: temp=44.9 sysload=0.25 cputime=85.261 memavail=7409056 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 651.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=7497107 bytes_read=924858 bytes_retransmit=9 bytes_invalid=0 send_seq=131985 receive_seq=131985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015544 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4612 bytes_read=16248 bytes_retransmit=0 bytes_invalid=0 send_seq=740 receive_seq=740 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998569 adj=49996612 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=39275 bytes_read=1244870 bytes_retransmit=9 bytes_invalid=0 send_seq=5225 receive_seq=5225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000177 adj=63997656 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13704 bytes_read=87080 bytes_retransmit=9 bytes_invalid=0 send_seq=1483 receive_seq=1483 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997588 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4771 bytes_read=161464 bytes_retransmit=9 bytes_invalid=0 send_seq=746 receive_seq=746 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5365 bytes_read=15954 bytes_retransmit=9 bytes_invalid=0 send_seq=741 receive_seq=741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48441 bytes_read=439643 bytes_retransmit=0 bytes_invalid=0 send_seq=4378 receive_seq=4378 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999899 adj=31998664 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.011 th0: temp=47.0 th1: temp=46.0 th2: temp=46.6 th3: temp=44.8 sysload=0.23 cputime=85.304 memavail=7409056 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 652.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=7497405 bytes_read=925283 bytes_retransmit=9 bytes_invalid=0 send_seq=132008 receive_seq=132008 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015544 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4618 bytes_read=16264 bytes_retransmit=0 bytes_invalid=0 send_seq=741 receive_seq=741 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998569 adj=49996620 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=39281 bytes_read=1244984 bytes_retransmit=9 bytes_invalid=0 send_seq=5226 receive_seq=5226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000177 adj=63997662 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13710 bytes_read=87194 bytes_retransmit=9 bytes_invalid=0 send_seq=1484 receive_seq=1484 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997542 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4777 bytes_read=161743 bytes_retransmit=9 bytes_invalid=0 send_seq=747 receive_seq=747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5371 bytes_read=15981 bytes_retransmit=9 bytes_invalid=0 send_seq=742 receive_seq=742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48447 bytes_read=439999 bytes_retransmit=0 bytes_invalid=0 send_seq=4379 receive_seq=4379 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999899 adj=31998653 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.011 th0: temp=46.9 th1: temp=45.9 th2: temp=46.9 th3: temp=44.7 sysload=0.23 cputime=85.346 memavail=7409056 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 653.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=7497698 bytes_read=925703 bytes_retransmit=9 bytes_invalid=0 send_seq=132030 receive_seq=132030 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015540 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4624 bytes_read=16280 bytes_retransmit=0 bytes_invalid=0 send_seq=742 receive_seq=742 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998569 adj=49996625 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=39287 bytes_read=1245098 bytes_retransmit=9 bytes_invalid=0 send_seq=5227 receive_seq=5227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000177 adj=63997680 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13716 bytes_read=87308 bytes_retransmit=9 bytes_invalid=0 send_seq=1485 receive_seq=1485 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997513 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4783 bytes_read=162007 bytes_retransmit=9 bytes_invalid=0 send_seq=748 receive_seq=748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5377 bytes_read=15997 bytes_retransmit=9 bytes_invalid=0 send_seq=743 receive_seq=743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48453 bytes_read=440355 bytes_retransmit=0 bytes_invalid=0 send_seq=4380 receive_seq=4380 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999899 adj=31998648 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=46.7 th1: temp=46.2 th2: temp=46.6 th3: temp=45.0 sysload=0.23 cputime=85.389 memavail=7409056 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 654.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=7497996 bytes_read=926153 bytes_retransmit=9 bytes_invalid=0 send_seq=132053 receive_seq=132053 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015537 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4630 bytes_read=16296 bytes_retransmit=0 bytes_invalid=0 send_seq=743 receive_seq=743 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998568 adj=49996634 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=39293 bytes_read=1245198 bytes_retransmit=9 bytes_invalid=0 send_seq=5228 receive_seq=5228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000176 adj=63997684 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13722 bytes_read=87408 bytes_retransmit=9 bytes_invalid=0 send_seq=1486 receive_seq=1486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4789 bytes_read=162241 bytes_retransmit=9 bytes_invalid=0 send_seq=749 receive_seq=749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5383 bytes_read=16013 bytes_retransmit=9 bytes_invalid=0 send_seq=744 receive_seq=744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48459 bytes_read=440711 bytes_retransmit=0 bytes_invalid=0 send_seq=4381 receive_seq=4381 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999898 adj=31998658 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=47.1 th1: temp=46.0 th2: temp=46.7 th3: temp=44.9 sysload=0.23 cputime=85.430 memavail=7409056 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 655.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7498294 bytes_read=926592 bytes_retransmit=9 bytes_invalid=0 send_seq=132076 receive_seq=132076 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015536 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4636 bytes_read=16312 bytes_retransmit=0 bytes_invalid=0 send_seq=744 receive_seq=744 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998568 adj=49996628 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=39299 bytes_read=1245312 bytes_retransmit=9 bytes_invalid=0 send_seq=5229 receive_seq=5229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997679 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13728 bytes_read=87522 bytes_retransmit=9 bytes_invalid=0 send_seq=1487 receive_seq=1487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000017 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4795 bytes_read=162535 bytes_retransmit=9 bytes_invalid=0 send_seq=750 receive_seq=750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5389 bytes_read=16029 bytes_retransmit=9 bytes_invalid=0 send_seq=745 receive_seq=745 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48465 bytes_read=441067 bytes_retransmit=0 bytes_invalid=0 send_seq=4382 receive_seq=4382 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999898 adj=31998655 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=46.6 th1: temp=45.9 th2: temp=46.7 th3: temp=44.9 sysload=0.23 cputime=85.474 memavail=7410824 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 656.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7498592 bytes_read=927017 bytes_retransmit=9 bytes_invalid=0 send_seq=132099 receive_seq=132099 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015535 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4642 bytes_read=16341 bytes_retransmit=0 bytes_invalid=0 send_seq=745 receive_seq=745 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998568 adj=49996626 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39305 bytes_read=1245440 bytes_retransmit=9 bytes_invalid=0 send_seq=5230 receive_seq=5230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997675 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13734 bytes_read=87650 bytes_retransmit=9 bytes_invalid=0 send_seq=1488 receive_seq=1488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000015 adj=63997478 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4801 bytes_read=162769 bytes_retransmit=9 bytes_invalid=0 send_seq=751 receive_seq=751 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5395 bytes_read=16045 bytes_retransmit=9 bytes_invalid=0 send_seq=746 receive_seq=746 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48471 bytes_read=441423 bytes_retransmit=0 bytes_invalid=0 send_seq=4383 receive_seq=4383 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999898 adj=31998649 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=47.0 th1: temp=45.9 th2: temp=46.6 th3: temp=44.7 sysload=0.21 cputime=85.516 memavail=7410824 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 657.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7498890 bytes_read=927471 bytes_retransmit=9 bytes_invalid=0 send_seq=132122 receive_seq=132122 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015532 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4648 bytes_read=16357 bytes_retransmit=0 bytes_invalid=0 send_seq=746 receive_seq=746 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998568 adj=49996621 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39311 bytes_read=1245540 bytes_retransmit=9 bytes_invalid=0 send_seq=5231 receive_seq=5231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000174 adj=63997671 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13740 bytes_read=87750 bytes_retransmit=9 bytes_invalid=0 send_seq=1489 receive_seq=1489 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000014 adj=63997470 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=4807 bytes_read=163003 bytes_retransmit=9 bytes_invalid=0 send_seq=752 receive_seq=752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997649 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5401 bytes_read=16072 bytes_retransmit=9 bytes_invalid=0 send_seq=747 receive_seq=747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48477 bytes_read=441779 bytes_retransmit=0 bytes_invalid=0 send_seq=4384 receive_seq=4384 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999897 adj=31998645 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.011 th0: temp=46.9 th1: temp=46.0 th2: temp=46.8 th3: temp=45.0 sysload=0.21 cputime=85.554 memavail=7410824 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 658.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7499188 bytes_read=927896 bytes_retransmit=9 bytes_invalid=0 send_seq=132145 receive_seq=132145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015533 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4654 bytes_read=16373 bytes_retransmit=0 bytes_invalid=0 send_seq=747 receive_seq=747 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998569 adj=49996636 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39317 bytes_read=1245654 bytes_retransmit=9 bytes_invalid=0 send_seq=5232 receive_seq=5232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000173 adj=63997670 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13746 bytes_read=87864 bytes_retransmit=9 bytes_invalid=0 send_seq=1490 receive_seq=1490 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000014 adj=63997470 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4813 bytes_read=163312 bytes_retransmit=9 bytes_invalid=0 send_seq=753 receive_seq=753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997649 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5407 bytes_read=16088 bytes_retransmit=9 bytes_invalid=0 send_seq=748 receive_seq=748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48483 bytes_read=442135 bytes_retransmit=0 bytes_invalid=0 send_seq=4385 receive_seq=4385 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999898 adj=31998645 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.011 th0: temp=47.1 th1: temp=46.0 th2: temp=46.7 th3: temp=44.9 sysload=0.21 cputime=85.596 memavail=7410824 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 659.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7499486 bytes_read=928321 bytes_retransmit=9 bytes_invalid=0 send_seq=132168 receive_seq=132168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015533 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4660 bytes_read=16389 bytes_retransmit=0 bytes_invalid=0 send_seq=748 receive_seq=748 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998569 adj=49996643 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39323 bytes_read=1245768 bytes_retransmit=9 bytes_invalid=0 send_seq=5233 receive_seq=5233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000172 adj=63997656 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13752 bytes_read=87978 bytes_retransmit=9 bytes_invalid=0 send_seq=1491 receive_seq=1491 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000013 adj=63997479 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4819 bytes_read=163546 bytes_retransmit=9 bytes_invalid=0 send_seq=754 receive_seq=754 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999523 adj=47997649 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5413 bytes_read=16104 bytes_retransmit=9 bytes_invalid=0 send_seq=749 receive_seq=749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999444 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48489 bytes_read=442491 bytes_retransmit=0 bytes_invalid=0 send_seq=4386 receive_seq=4386 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998663 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=47.1 th1: temp=46.0 th2: temp=46.6 th3: temp=45.0 sysload=0.21 cputime=85.639 memavail=7410824 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 660.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7499784 bytes_read=928790 bytes_retransmit=9 bytes_invalid=0 send_seq=132191 receive_seq=132191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015533 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4666 bytes_read=16405 bytes_retransmit=0 bytes_invalid=0 send_seq=749 receive_seq=749 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998569 adj=49996645 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39329 bytes_read=1245868 bytes_retransmit=9 bytes_invalid=0 send_seq=5234 receive_seq=5234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000172 adj=63997654 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13758 bytes_read=88078 bytes_retransmit=9 bytes_invalid=0 send_seq=1492 receive_seq=1492 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000011 adj=63997472 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4825 bytes_read=163780 bytes_retransmit=9 bytes_invalid=0 send_seq=755 receive_seq=755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5419 bytes_read=16120 bytes_retransmit=9 bytes_invalid=0 send_seq=750 receive_seq=750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48495 bytes_read=442847 bytes_retransmit=0 bytes_invalid=0 send_seq=4387 receive_seq=4387 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998687 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=47.1 th1: temp=46.5 th2: temp=46.9 th3: temp=44.9 sysload=0.21 cputime=85.681 memavail=7410824 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 661.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7500082 bytes_read=929215 bytes_retransmit=9 bytes_invalid=0 send_seq=132214 receive_seq=132214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015533 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4672 bytes_read=16434 bytes_retransmit=0 bytes_invalid=0 send_seq=750 receive_seq=750 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998570 adj=49996644 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39335 bytes_read=1245996 bytes_retransmit=9 bytes_invalid=0 send_seq=5235 receive_seq=5235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000171 adj=63997653 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13764 bytes_read=88206 bytes_retransmit=9 bytes_invalid=0 send_seq=1493 receive_seq=1493 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000010 adj=63997467 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4831 bytes_read=164074 bytes_retransmit=9 bytes_invalid=0 send_seq=756 receive_seq=756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997692 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5425 bytes_read=16136 bytes_retransmit=9 bytes_invalid=0 send_seq=751 receive_seq=751 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=25.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48501 bytes_read=443203 bytes_retransmit=0 bytes_invalid=0 send_seq=4388 receive_seq=4388 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998682 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.011 th0: temp=47.5 th1: temp=46.2 th2: temp=47.0 th3: temp=45.1 sysload=0.19 cputime=85.723 memavail=7410824 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 662.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7500380 bytes_read=929640 bytes_retransmit=9 bytes_invalid=0 send_seq=132237 receive_seq=132237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015535 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4678 bytes_read=16450 bytes_retransmit=0 bytes_invalid=0 send_seq=751 receive_seq=751 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998571 adj=49996649 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39341 bytes_read=1246110 bytes_retransmit=9 bytes_invalid=0 send_seq=5236 receive_seq=5236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000171 adj=63997653 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13770 bytes_read=88320 bytes_retransmit=9 bytes_invalid=0 send_seq=1494 receive_seq=1494 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000010 adj=63997465 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4837 bytes_read=164308 bytes_retransmit=9 bytes_invalid=0 send_seq=757 receive_seq=757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5431 bytes_read=16163 bytes_retransmit=9 bytes_invalid=0 send_seq=752 receive_seq=752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48507 bytes_read=443559 bytes_retransmit=0 bytes_invalid=0 send_seq=4389 receive_seq=4389 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999900 adj=31998671 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.011 th0: temp=47.2 th1: temp=46.1 th2: temp=46.8 th3: temp=45.0 sysload=0.19 cputime=85.766 memavail=7410824 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 663.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7500678 bytes_read=930094 bytes_retransmit=9 bytes_invalid=0 send_seq=132260 receive_seq=132260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015538 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4684 bytes_read=16466 bytes_retransmit=0 bytes_invalid=0 send_seq=752 receive_seq=752 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998574 adj=49996650 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39347 bytes_read=1246210 bytes_retransmit=9 bytes_invalid=0 send_seq=5237 receive_seq=5237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997654 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13776 bytes_read=88420 bytes_retransmit=9 bytes_invalid=0 send_seq=1495 receive_seq=1495 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997466 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4843 bytes_read=164557 bytes_retransmit=9 bytes_invalid=0 send_seq=758 receive_seq=758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997669 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5437 bytes_read=16179 bytes_retransmit=9 bytes_invalid=0 send_seq=753 receive_seq=753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48513 bytes_read=443915 bytes_retransmit=0 bytes_invalid=0 send_seq=4390 receive_seq=4390 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998662 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=46.8 th1: temp=45.9 th2: temp=46.8 th3: temp=45.0 sysload=0.19 cputime=85.808 memavail=7410864 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 664.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7500982 bytes_read=930535 bytes_retransmit=9 bytes_invalid=0 send_seq=132284 receive_seq=132284 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015539 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4696 bytes_read=16498 bytes_retransmit=0 bytes_invalid=0 send_seq=754 receive_seq=754 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998578 adj=49996696 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39359 bytes_read=1246354 bytes_retransmit=9 bytes_invalid=0 send_seq=5239 receive_seq=5239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997772 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13788 bytes_read=88550 bytes_retransmit=9 bytes_invalid=0 send_seq=1497 receive_seq=1497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997458 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4855 bytes_read=164867 bytes_retransmit=9 bytes_invalid=0 send_seq=760 receive_seq=760 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5449 bytes_read=16211 bytes_retransmit=9 bytes_invalid=0 send_seq=755 receive_seq=755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999444 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48525 bytes_read=444287 bytes_retransmit=0 bytes_invalid=0 send_seq=4392 receive_seq=4392 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999902 adj=31998687 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=47.0 th1: temp=46.0 th2: temp=47.0 th3: temp=44.9 sysload=0.19 cputime=85.853 memavail=7410864 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 665.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=7501280 bytes_read=930971 bytes_retransmit=9 bytes_invalid=0 send_seq=132307 receive_seq=132307 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015540 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4702 bytes_read=16514 bytes_retransmit=0 bytes_invalid=0 send_seq=755 receive_seq=755 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998580 adj=49996739 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39365 bytes_read=1246454 bytes_retransmit=9 bytes_invalid=0 send_seq=5240 receive_seq=5240 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997869 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13794 bytes_read=88664 bytes_retransmit=9 bytes_invalid=0 send_seq=1498 receive_seq=1498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000008 adj=63997469 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4861 bytes_read=165101 bytes_retransmit=9 bytes_invalid=0 send_seq=761 receive_seq=761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5455 bytes_read=16227 bytes_retransmit=9 bytes_invalid=0 send_seq=756 receive_seq=756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48531 bytes_read=444643 bytes_retransmit=0 bytes_invalid=0 send_seq=4393 receive_seq=4393 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998681 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=47.0 th1: temp=46.3 th2: temp=46.8 th3: temp=45.0 sysload=0.19 cputime=85.900 memavail=7407776 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 666.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=7501578 bytes_read=931425 bytes_retransmit=9 bytes_invalid=0 send_seq=132330 receive_seq=132330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015540 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4708 bytes_read=16543 bytes_retransmit=0 bytes_invalid=0 send_seq=756 receive_seq=756 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998582 adj=49996742 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39371 bytes_read=1246568 bytes_retransmit=9 bytes_invalid=0 send_seq=5241 receive_seq=5241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997812 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13800 bytes_read=88778 bytes_retransmit=9 bytes_invalid=0 send_seq=1499 receive_seq=1499 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4867 bytes_read=165335 bytes_retransmit=9 bytes_invalid=0 send_seq=762 receive_seq=762 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5461 bytes_read=16243 bytes_retransmit=9 bytes_invalid=0 send_seq=757 receive_seq=757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48537 bytes_read=444999 bytes_retransmit=0 bytes_invalid=0 send_seq=4394 receive_seq=4394 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998665 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.011 th0: temp=47.2 th1: temp=45.9 th2: temp=46.6 th3: temp=45.0 sysload=0.18 cputime=85.943 memavail=7407776 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 667.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=7501876 bytes_read=931850 bytes_retransmit=9 bytes_invalid=0 send_seq=132353 receive_seq=132353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015539 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4714 bytes_read=16559 bytes_retransmit=0 bytes_invalid=0 send_seq=757 receive_seq=757 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998583 adj=49996741 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39377 bytes_read=1246696 bytes_retransmit=9 bytes_invalid=0 send_seq=5242 receive_seq=5242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997860 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13806 bytes_read=88892 bytes_retransmit=9 bytes_invalid=0 send_seq=1500 receive_seq=1500 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997491 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4873 bytes_read=165629 bytes_retransmit=9 bytes_invalid=0 send_seq=763 receive_seq=763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5467 bytes_read=16270 bytes_retransmit=9 bytes_invalid=0 send_seq=758 receive_seq=758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48543 bytes_read=445355 bytes_retransmit=0 bytes_invalid=0 send_seq=4395 receive_seq=4395 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998663 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=47.2 th1: temp=46.3 th2: temp=46.6 th3: temp=45.0 sysload=0.18 cputime=85.985 memavail=7407776 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 668.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=7502169 bytes_read=932270 bytes_retransmit=9 bytes_invalid=0 send_seq=132375 receive_seq=132375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015548 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4720 bytes_read=16575 bytes_retransmit=0 bytes_invalid=0 send_seq=758 receive_seq=758 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998584 adj=49996746 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39383 bytes_read=1246796 bytes_retransmit=9 bytes_invalid=0 send_seq=5243 receive_seq=5243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997814 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13812 bytes_read=89006 bytes_retransmit=9 bytes_invalid=0 send_seq=1501 receive_seq=1501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997515 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4879 bytes_read=165878 bytes_retransmit=9 bytes_invalid=0 send_seq=764 receive_seq=764 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5473 bytes_read=16286 bytes_retransmit=9 bytes_invalid=0 send_seq=759 receive_seq=759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48549 bytes_read=445711 bytes_retransmit=0 bytes_invalid=0 send_seq=4396 receive_seq=4396 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998666 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=47.3 th1: temp=46.2 th2: temp=46.8 th3: temp=45.2 sysload=0.18 cputime=86.027 memavail=7407776 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 669.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=7502467 bytes_read=932724 bytes_retransmit=9 bytes_invalid=0 send_seq=132398 receive_seq=132398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015546 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4726 bytes_read=16591 bytes_retransmit=0 bytes_invalid=0 send_seq=759 receive_seq=759 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998586 adj=49996719 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39389 bytes_read=1246896 bytes_retransmit=9 bytes_invalid=0 send_seq=5244 receive_seq=5244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997815 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13818 bytes_read=89106 bytes_retransmit=9 bytes_invalid=0 send_seq=1502 receive_seq=1502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997497 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4885 bytes_read=166112 bytes_retransmit=9 bytes_invalid=0 send_seq=765 receive_seq=765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997629 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5479 bytes_read=16302 bytes_retransmit=9 bytes_invalid=0 send_seq=760 receive_seq=760 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48555 bytes_read=446067 bytes_retransmit=0 bytes_invalid=0 send_seq=4397 receive_seq=4397 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998646 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.2 th2: temp=46.8 th3: temp=45.1 sysload=0.18 cputime=86.069 memavail=7407776 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 670.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7502765 bytes_read=933164 bytes_retransmit=9 bytes_invalid=0 send_seq=132421 receive_seq=132421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015544 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4732 bytes_read=16607 bytes_retransmit=0 bytes_invalid=0 send_seq=760 receive_seq=760 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998589 adj=49996729 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39395 bytes_read=1247024 bytes_retransmit=9 bytes_invalid=0 send_seq=5245 receive_seq=5245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997767 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13824 bytes_read=89234 bytes_retransmit=9 bytes_invalid=0 send_seq=1503 receive_seq=1503 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000010 adj=63997494 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4891 bytes_read=166406 bytes_retransmit=9 bytes_invalid=0 send_seq=766 receive_seq=766 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997634 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5485 bytes_read=16318 bytes_retransmit=9 bytes_invalid=0 send_seq=761 receive_seq=761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=25.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48561 bytes_read=446423 bytes_retransmit=0 bytes_invalid=0 send_seq=4398 receive_seq=4398 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998653 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=47.3 th1: temp=46.0 th2: temp=47.2 th3: temp=45.1 sysload=0.18 cputime=86.114 memavail=7407780 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 671.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7503063 bytes_read=933589 bytes_retransmit=9 bytes_invalid=0 send_seq=132444 receive_seq=132444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015548 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4738 bytes_read=16623 bytes_retransmit=0 bytes_invalid=0 send_seq=761 receive_seq=761 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998591 adj=49996759 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=39401 bytes_read=1247138 bytes_retransmit=9 bytes_invalid=0 send_seq=5246 receive_seq=5246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997730 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13830 bytes_read=89334 bytes_retransmit=9 bytes_invalid=0 send_seq=1504 receive_seq=1504 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4897 bytes_read=166640 bytes_retransmit=9 bytes_invalid=0 send_seq=767 receive_seq=767 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999523 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5491 bytes_read=16334 bytes_retransmit=9 bytes_invalid=0 send_seq=762 receive_seq=762 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48567 bytes_read=446779 bytes_retransmit=0 bytes_invalid=0 send_seq=4399 receive_seq=4399 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998662 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.3 th2: temp=46.9 th3: temp=45.0 sysload=0.16 cputime=86.158 memavail=7407780 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 672.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7503351 bytes_read=934033 bytes_retransmit=9 bytes_invalid=0 send_seq=132465 receive_seq=132465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015550 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4744 bytes_read=16652 bytes_retransmit=0 bytes_invalid=0 send_seq=762 receive_seq=762 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998593 adj=49996759 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=39407 bytes_read=1247238 bytes_retransmit=9 bytes_invalid=0 send_seq=5247 receive_seq=5247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997824 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13836 bytes_read=89448 bytes_retransmit=9 bytes_invalid=0 send_seq=1505 receive_seq=1505 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4903 bytes_read=166874 bytes_retransmit=9 bytes_invalid=0 send_seq=768 receive_seq=768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999523 adj=47997630 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5497 bytes_read=16361 bytes_retransmit=9 bytes_invalid=0 send_seq=763 receive_seq=763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48573 bytes_read=447135 bytes_retransmit=0 bytes_invalid=0 send_seq=4400 receive_seq=4400 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999903 adj=31998660 coil_temp=17.5 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=47.3 th1: temp=46.1 th2: temp=46.8 th3: temp=45.1 sysload=0.16 cputime=86.202 memavail=7407780 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 673.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7503639 bytes_read=934448 bytes_retransmit=9 bytes_invalid=0 send_seq=132486 receive_seq=132486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015548 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4750 bytes_read=16668 bytes_retransmit=0 bytes_invalid=0 send_seq=763 receive_seq=763 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998594 adj=49996753 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=39413 bytes_read=1247366 bytes_retransmit=9 bytes_invalid=0 send_seq=5248 receive_seq=5248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997783 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13842 bytes_read=89576 bytes_retransmit=9 bytes_invalid=0 send_seq=1506 receive_seq=1506 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000010 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4909 bytes_read=167183 bytes_retransmit=9 bytes_invalid=0 send_seq=769 receive_seq=769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5503 bytes_read=16377 bytes_retransmit=9 bytes_invalid=0 send_seq=764 receive_seq=764 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48579 bytes_read=447491 bytes_retransmit=0 bytes_invalid=0 send_seq=4401 receive_seq=4401 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999904 adj=31998690 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=47.2 th1: temp=46.4 th2: temp=46.7 th3: temp=44.8 sysload=0.16 cputime=86.246 memavail=7407780 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 674.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7503937 bytes_read=934873 bytes_retransmit=9 bytes_invalid=0 send_seq=132509 receive_seq=132509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015553 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4756 bytes_read=16684 bytes_retransmit=0 bytes_invalid=0 send_seq=764 receive_seq=764 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998597 adj=49996749 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=39419 bytes_read=1247466 bytes_retransmit=9 bytes_invalid=0 send_seq=5249 receive_seq=5249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997736 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13848 bytes_read=89676 bytes_retransmit=9 bytes_invalid=0 send_seq=1507 receive_seq=1507 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4915 bytes_read=167417 bytes_retransmit=9 bytes_invalid=0 send_seq=770 receive_seq=770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5509 bytes_read=16393 bytes_retransmit=9 bytes_invalid=0 send_seq=765 receive_seq=765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48585 bytes_read=447847 bytes_retransmit=0 bytes_invalid=0 send_seq=4402 receive_seq=4402 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999903 adj=31998686 coil_temp=17.5 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.3 th2: temp=47.1 th3: temp=44.9 sysload=0.16 cputime=86.291 memavail=7407780 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 675.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7504235 bytes_read=935340 bytes_retransmit=9 bytes_invalid=0 send_seq=132532 receive_seq=132532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015563 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4762 bytes_read=16700 bytes_retransmit=0 bytes_invalid=0 send_seq=765 receive_seq=765 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998599 adj=49996753 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=39425 bytes_read=1247566 bytes_retransmit=9 bytes_invalid=0 send_seq=5250 receive_seq=5250 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997705 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13854 bytes_read=89776 bytes_retransmit=9 bytes_invalid=0 send_seq=1508 receive_seq=1508 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000010 adj=63997497 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4921 bytes_read=167651 bytes_retransmit=9 bytes_invalid=0 send_seq=771 receive_seq=771 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5515 bytes_read=16409 bytes_retransmit=9 bytes_invalid=0 send_seq=766 receive_seq=766 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48591 bytes_read=448203 bytes_retransmit=0 bytes_invalid=0 send_seq=4403 receive_seq=4403 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999902 adj=31998664 coil_temp=17.5 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=47.3 th1: temp=46.1 th2: temp=46.9 th3: temp=45.1 sysload=0.16 cputime=86.336 memavail=7406548 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 676.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7504523 bytes_read=935753 bytes_retransmit=9 bytes_invalid=0 send_seq=132553 receive_seq=132553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015571 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=4768 bytes_read=16716 bytes_retransmit=0 bytes_invalid=0 send_seq=766 receive_seq=766 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998602 adj=49996746 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39431 bytes_read=1247708 bytes_retransmit=9 bytes_invalid=0 send_seq=5251 receive_seq=5251 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997652 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13860 bytes_read=89904 bytes_retransmit=9 bytes_invalid=0 send_seq=1509 receive_seq=1509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997489 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4927 bytes_read=167945 bytes_retransmit=9 bytes_invalid=0 send_seq=772 receive_seq=772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5521 bytes_read=16425 bytes_retransmit=9 bytes_invalid=0 send_seq=767 receive_seq=767 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48597 bytes_read=448559 bytes_retransmit=0 bytes_invalid=0 send_seq=4404 receive_seq=4404 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999902 adj=31998641 coil_temp=17.5 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.6 th2: temp=47.0 th3: temp=45.3 sysload=0.15 cputime=86.380 memavail=7406548 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 677.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7504821 bytes_read=936178 bytes_retransmit=9 bytes_invalid=0 send_seq=132576 receive_seq=132576 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015570 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4774 bytes_read=16745 bytes_retransmit=0 bytes_invalid=0 send_seq=767 receive_seq=767 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998603 adj=49996746 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39437 bytes_read=1247808 bytes_retransmit=9 bytes_invalid=0 send_seq=5252 receive_seq=5252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997636 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13866 bytes_read=90018 bytes_retransmit=9 bytes_invalid=0 send_seq=1510 receive_seq=1510 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997475 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4933 bytes_read=168179 bytes_retransmit=9 bytes_invalid=0 send_seq=773 receive_seq=773 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997630 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5527 bytes_read=16452 bytes_retransmit=9 bytes_invalid=0 send_seq=768 receive_seq=768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999439 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=26.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48603 bytes_read=448915 bytes_retransmit=0 bytes_invalid=0 send_seq=4405 receive_seq=4405 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999903 adj=31998628 coil_temp=17.5 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.1 th2: temp=47.1 th3: temp=45.1 sysload=0.15 cputime=86.423 memavail=7406548 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 678.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7505109 bytes_read=936622 bytes_retransmit=9 bytes_invalid=0 send_seq=132597 receive_seq=132597 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015574 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4780 bytes_read=16761 bytes_retransmit=0 bytes_invalid=0 send_seq=768 receive_seq=768 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998606 adj=49996755 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39443 bytes_read=1247908 bytes_retransmit=9 bytes_invalid=0 send_seq=5253 receive_seq=5253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997698 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13872 bytes_read=90118 bytes_retransmit=9 bytes_invalid=0 send_seq=1511 receive_seq=1511 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000008 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4939 bytes_read=168428 bytes_retransmit=9 bytes_invalid=0 send_seq=774 receive_seq=774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5533 bytes_read=16468 bytes_retransmit=9 bytes_invalid=0 send_seq=769 receive_seq=769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48609 bytes_read=449271 bytes_retransmit=0 bytes_invalid=0 send_seq=4406 receive_seq=4406 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998652 coil_temp=17.5 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=47.3 th1: temp=46.3 th2: temp=46.9 th3: temp=45.1 sysload=0.15 cputime=86.466 memavail=7406548 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 679.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7505402 bytes_read=937042 bytes_retransmit=9 bytes_invalid=0 send_seq=132619 receive_seq=132619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015579 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4786 bytes_read=16777 bytes_retransmit=0 bytes_invalid=0 send_seq=769 receive_seq=769 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998608 adj=49996759 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39449 bytes_read=1248036 bytes_retransmit=9 bytes_invalid=0 send_seq=5254 receive_seq=5254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997772 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13878 bytes_read=90246 bytes_retransmit=9 bytes_invalid=0 send_seq=1512 receive_seq=1512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997468 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4945 bytes_read=168722 bytes_retransmit=9 bytes_invalid=0 send_seq=775 receive_seq=775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5539 bytes_read=16484 bytes_retransmit=9 bytes_invalid=0 send_seq=770 receive_seq=770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999444 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48615 bytes_read=449627 bytes_retransmit=0 bytes_invalid=0 send_seq=4407 receive_seq=4407 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998692 coil_temp=17.5 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.3 th2: temp=47.0 th3: temp=45.2 sysload=0.15 cputime=86.508 memavail=7406548 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 680.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7505700 bytes_read=937482 bytes_retransmit=9 bytes_invalid=0 send_seq=132642 receive_seq=132642 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015590 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4792 bytes_read=16793 bytes_retransmit=0 bytes_invalid=0 send_seq=770 receive_seq=770 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998610 adj=49996758 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39455 bytes_read=1248136 bytes_retransmit=9 bytes_invalid=0 send_seq=5255 receive_seq=5255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997714 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13884 bytes_read=90346 bytes_retransmit=9 bytes_invalid=0 send_seq=1513 receive_seq=1513 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997458 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4951 bytes_read=168956 bytes_retransmit=9 bytes_invalid=0 send_seq=776 receive_seq=776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5545 bytes_read=16500 bytes_retransmit=9 bytes_invalid=0 send_seq=771 receive_seq=771 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=26.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48621 bytes_read=449983 bytes_retransmit=0 bytes_invalid=0 send_seq=4408 receive_seq=4408 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998744 coil_temp=17.5 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=47.3 th1: temp=46.4 th2: temp=47.1 th3: temp=45.2 sysload=0.15 cputime=86.550 memavail=7406608 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 681.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7505998 bytes_read=937936 bytes_retransmit=9 bytes_invalid=0 send_seq=132665 receive_seq=132665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015591 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4798 bytes_read=16809 bytes_retransmit=0 bytes_invalid=0 send_seq=771 receive_seq=771 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998612 adj=49996742 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39461 bytes_read=1248250 bytes_retransmit=9 bytes_invalid=0 send_seq=5256 receive_seq=5256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997662 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=13890 bytes_read=90446 bytes_retransmit=9 bytes_invalid=0 send_seq=1514 receive_seq=1514 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997435 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4957 bytes_read=169190 bytes_retransmit=9 bytes_invalid=0 send_seq=777 receive_seq=777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997613 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5551 bytes_read=16516 bytes_retransmit=9 bytes_invalid=0 send_seq=772 receive_seq=772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48627 bytes_read=450339 bytes_retransmit=0 bytes_invalid=0 send_seq=4409 receive_seq=4409 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998695 coil_temp=17.5 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.7 th2: temp=46.9 th3: temp=45.1 sysload=0.14 cputime=86.591 memavail=7406608 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 682.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7506296 bytes_read=938361 bytes_retransmit=9 bytes_invalid=0 send_seq=132688 receive_seq=132688 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015616 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4804 bytes_read=16838 bytes_retransmit=0 bytes_invalid=0 send_seq=772 receive_seq=772 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998616 adj=49996753 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39467 bytes_read=1248378 bytes_retransmit=9 bytes_invalid=0 send_seq=5257 receive_seq=5257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997767 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13896 bytes_read=90588 bytes_retransmit=9 bytes_invalid=0 send_seq=1515 receive_seq=1515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997443 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=4963 bytes_read=169484 bytes_retransmit=9 bytes_invalid=0 send_seq=778 receive_seq=778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997614 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5557 bytes_read=16543 bytes_retransmit=9 bytes_invalid=0 send_seq=773 receive_seq=773 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48633 bytes_read=450695 bytes_retransmit=0 bytes_invalid=0 send_seq=4410 receive_seq=4410 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998671 coil_temp=17.5 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.4 th2: temp=47.0 th3: temp=45.2 sysload=0.14 cputime=86.638 memavail=7400812 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 683.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7506594 bytes_read=938786 bytes_retransmit=9 bytes_invalid=0 send_seq=132711 receive_seq=132711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015615 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4810 bytes_read=16854 bytes_retransmit=0 bytes_invalid=0 send_seq=773 receive_seq=773 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998619 adj=49996749 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39473 bytes_read=1248478 bytes_retransmit=9 bytes_invalid=0 send_seq=5258 receive_seq=5258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997658 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13902 bytes_read=90688 bytes_retransmit=9 bytes_invalid=0 send_seq=1516 receive_seq=1516 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000008 adj=63997415 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4969 bytes_read=169733 bytes_retransmit=9 bytes_invalid=0 send_seq=779 receive_seq=779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5563 bytes_read=16559 bytes_retransmit=9 bytes_invalid=0 send_seq=774 receive_seq=774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999426 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48639 bytes_read=451051 bytes_retransmit=0 bytes_invalid=0 send_seq=4411 receive_seq=4411 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998628 coil_temp=17.5 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.3 th2: temp=47.1 th3: temp=45.3 sysload=0.14 cputime=86.680 memavail=7406952 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 684.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7506887 bytes_read=939235 bytes_retransmit=9 bytes_invalid=0 send_seq=132733 receive_seq=132733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015618 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4816 bytes_read=16870 bytes_retransmit=0 bytes_invalid=0 send_seq=774 receive_seq=774 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998621 adj=49996766 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39479 bytes_read=1248578 bytes_retransmit=9 bytes_invalid=0 send_seq=5259 receive_seq=5259 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997639 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13908 bytes_read=90788 bytes_retransmit=9 bytes_invalid=0 send_seq=1517 receive_seq=1517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997446 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4975 bytes_read=169967 bytes_retransmit=9 bytes_invalid=0 send_seq=780 receive_seq=780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5569 bytes_read=16575 bytes_retransmit=9 bytes_invalid=0 send_seq=775 receive_seq=775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48645 bytes_read=451407 bytes_retransmit=0 bytes_invalid=0 send_seq=4412 receive_seq=4412 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998628 coil_temp=17.5 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=47.4 th1: temp=46.5 th2: temp=46.9 th3: temp=45.2 sysload=0.14 cputime=86.721 memavail=7406952 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 685.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7507170 bytes_read=939660 bytes_retransmit=9 bytes_invalid=0 send_seq=132753 receive_seq=132753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015615 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4822 bytes_read=16886 bytes_retransmit=0 bytes_invalid=0 send_seq=775 receive_seq=775 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998623 adj=49996773 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39485 bytes_read=1248706 bytes_retransmit=9 bytes_invalid=0 send_seq=5260 receive_seq=5260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997616 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13914 bytes_read=90916 bytes_retransmit=9 bytes_invalid=0 send_seq=1518 receive_seq=1518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997442 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4981 bytes_read=170261 bytes_retransmit=9 bytes_invalid=0 send_seq=781 receive_seq=781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5575 bytes_read=16591 bytes_retransmit=9 bytes_invalid=0 send_seq=776 receive_seq=776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48651 bytes_read=451763 bytes_retransmit=0 bytes_invalid=0 send_seq=4413 receive_seq=4413 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998624 coil_temp=17.5 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.3 th2: temp=47.1 th3: temp=45.3 sysload=0.14 cputime=86.766 memavail=7408056 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 686.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=7507468 bytes_read=940081 bytes_retransmit=9 bytes_invalid=0 send_seq=132776 receive_seq=132776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015620 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=4828 bytes_read=16902 bytes_retransmit=0 bytes_invalid=0 send_seq=776 receive_seq=776 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998626 adj=49996791 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=39491 bytes_read=1248820 bytes_retransmit=9 bytes_invalid=0 send_seq=5261 receive_seq=5261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997615 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=13920 bytes_read=91016 bytes_retransmit=9 bytes_invalid=0 send_seq=1519 receive_seq=1519 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997472 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=4987 bytes_read=170495 bytes_retransmit=9 bytes_invalid=0 send_seq=782 receive_seq=782 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5581 bytes_read=16607 bytes_retransmit=9 bytes_invalid=0 send_seq=777 receive_seq=777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48657 bytes_read=452119 bytes_retransmit=0 bytes_invalid=0 send_seq=4414 receive_seq=4414 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998634 coil_temp=17.5 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=47.4 th1: temp=46.3 th2: temp=47.2 th3: temp=45.3 sysload=0.12 cputime=86.809 memavail=7408056 print_time=649.514 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 717.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=7523134 bytes_read=954008 bytes_retransmit=9 bytes_invalid=0 send_seq=133560 receive_seq=133560 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=0 freq=400015705 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5014 bytes_read=17483 bytes_retransmit=0 bytes_invalid=0 send_seq=807 receive_seq=807 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998726 adj=49996872 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=39677 bytes_read=1252259 bytes_retransmit=9 bytes_invalid=0 send_seq=5292 receive_seq=5292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997627 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14106 bytes_read=94469 bytes_retransmit=9 bytes_invalid=0 send_seq=1550 receive_seq=1550 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997444 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5173 bytes_read=178343 bytes_retransmit=9 bytes_invalid=0 send_seq=813 receive_seq=813 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997617 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5767 bytes_read=17180 bytes_retransmit=9 bytes_invalid=0 send_seq=808 receive_seq=808 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48843 bytes_read=463139 bytes_retransmit=0 bytes_invalid=0 send_seq=4445 receive_seq=4445 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998651 coil_temp=17.5 refs=0 mcu_temp=20.76 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.0 th2: temp=47.2 th3: temp=45.4 sysload=0.07 cputime=88.184 memavail=7407804 print_time=740.451 buffer_time=0.623 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 718.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=7536678 bytes_read=955461 bytes_retransmit=9 bytes_invalid=0 send_seq=133789 receive_seq=133789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=0 freq=400015740 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5020 bytes_read=17499 bytes_retransmit=0 bytes_invalid=0 send_seq=808 receive_seq=808 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998730 adj=49996872 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=39683 bytes_read=1252380 bytes_retransmit=9 bytes_invalid=0 send_seq=5293 receive_seq=5293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997583 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14112 bytes_read=94590 bytes_retransmit=9 bytes_invalid=0 send_seq=1551 receive_seq=1551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997436 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5179 bytes_read=178652 bytes_retransmit=9 bytes_invalid=0 send_seq=814 receive_seq=814 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997610 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5773 bytes_read=17196 bytes_retransmit=9 bytes_invalid=0 send_seq=809 receive_seq=809 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48849 bytes_read=463495 bytes_retransmit=0 bytes_invalid=0 send_seq=4446 receive_seq=4446 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998631 coil_temp=17.5 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=47.7 th1: temp=46.7 th2: temp=47.7 th3: temp=45.6 sysload=0.07 cputime=88.281 memavail=7407804 print_time=741.527 buffer_time=0.699 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 719.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=7549541 bytes_read=956863 bytes_retransmit=9 bytes_invalid=0 send_seq=134008 receive_seq=134008 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=651 freq=400015809 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5026 bytes_read=17515 bytes_retransmit=0 bytes_invalid=0 send_seq=809 receive_seq=809 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998732 adj=49996828 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=39689 bytes_read=1252479 bytes_retransmit=9 bytes_invalid=0 send_seq=5294 receive_seq=5294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997494 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14118 bytes_read=94689 bytes_retransmit=9 bytes_invalid=0 send_seq=1552 receive_seq=1552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997366 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5185 bytes_read=178886 bytes_retransmit=9 bytes_invalid=0 send_seq=815 receive_seq=815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997548 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5779 bytes_read=17212 bytes_retransmit=9 bytes_invalid=0 send_seq=810 receive_seq=810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999416 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48855 bytes_read=463851 bytes_retransmit=0 bytes_invalid=0 send_seq=4447 receive_seq=4447 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998588 coil_temp=17.5 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=47.7 th1: temp=46.8 th2: temp=47.5 th3: temp=45.6 sysload=0.07 cputime=88.376 memavail=7407804 print_time=742.604 buffer_time=0.774 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
webhooks client 4132488288: New connection
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t0' measurements
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 720.4: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=7562072 bytes_read=958278 bytes_retransmit=9 bytes_invalid=0 send_seq=134220 receive_seq=134220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=1563 freq=400015838 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5032 bytes_read=17531 bytes_retransmit=0 bytes_invalid=0 send_seq=810 receive_seq=810 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998735 adj=49996709 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=39816 bytes_read=1253372 bytes_retransmit=9 bytes_invalid=0 send_seq=5308 receive_seq=5308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997383 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14124 bytes_read=94789 bytes_retransmit=9 bytes_invalid=0 send_seq=1553 receive_seq=1553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000006 adj=63997229 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5191 bytes_read=179120 bytes_retransmit=9 bytes_invalid=0 send_seq=816 receive_seq=816 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997436 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5785 bytes_read=17228 bytes_retransmit=9 bytes_invalid=0 send_seq=811 receive_seq=811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999410 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48861 bytes_read=464207 bytes_retransmit=0 bytes_invalid=0 send_seq=4448 receive_seq=4448 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998533 coil_temp=17.5 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.6 th2: temp=47.5 th3: temp=45.5 sysload=0.07 cputime=88.483 memavail=7407824 print_time=743.680 buffer_time=0.850 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 721.4: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=7574603 bytes_read=959648 bytes_retransmit=9 bytes_invalid=0 send_seq=134432 receive_seq=134432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=2507 freq=400015853 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5038 bytes_read=17547 bytes_retransmit=0 bytes_invalid=0 send_seq=811 receive_seq=811 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998738 adj=49996706 toolboard_t0: mcu_awake=0.069 mcu_task_avg=0.000095 mcu_task_stddev=0.000074 bytes_write=39892 bytes_read=1256415 bytes_retransmit=9 bytes_invalid=0 send_seq=5319 receive_seq=5319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997451 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14130 bytes_read=94917 bytes_retransmit=9 bytes_invalid=0 send_seq=1554 receive_seq=1554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000007 adj=63997221 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5197 bytes_read=179414 bytes_retransmit=9 bytes_invalid=0 send_seq=817 receive_seq=817 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997448 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5791 bytes_read=17244 bytes_retransmit=9 bytes_invalid=0 send_seq=812 receive_seq=812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999402 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48867 bytes_read=464563 bytes_retransmit=0 bytes_invalid=0 send_seq=4449 receive_seq=4449 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998517 coil_temp=17.5 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.9 th2: temp=47.6 th3: temp=45.5 sysload=0.07 cputime=88.605 memavail=7407600 print_time=744.757 buffer_time=0.926 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 722.4: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=7587089 bytes_read=960973 bytes_retransmit=9 bytes_invalid=0 send_seq=134635 receive_seq=134635 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=3419 freq=400015853 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5044 bytes_read=17576 bytes_retransmit=0 bytes_invalid=0 send_seq=812 receive_seq=812 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998741 adj=49996733 toolboard_t0: mcu_awake=0.069 mcu_task_avg=0.000095 mcu_task_stddev=0.000074 bytes_write=39968 bytes_read=1259425 bytes_retransmit=9 bytes_invalid=0 send_seq=5330 receive_seq=5330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997523 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14136 bytes_read=95031 bytes_retransmit=9 bytes_invalid=0 send_seq=1555 receive_seq=1555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000008 adj=63997269 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5203 bytes_read=179648 bytes_retransmit=9 bytes_invalid=0 send_seq=818 receive_seq=818 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997463 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5797 bytes_read=17271 bytes_retransmit=9 bytes_invalid=0 send_seq=813 receive_seq=813 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999411 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=26.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48873 bytes_read=464919 bytes_retransmit=0 bytes_invalid=0 send_seq=4450 receive_seq=4450 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998528 coil_temp=17.5 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.4 th2: temp=47.2 th3: temp=45.5 sysload=0.07 cputime=88.728 memavail=7407600 print_time=745.833 buffer_time=1.003 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 723.4: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=7600141 bytes_read=962412 bytes_retransmit=9 bytes_invalid=0 send_seq=134855 receive_seq=134855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=3899 freq=400015890 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5050 bytes_read=17592 bytes_retransmit=0 bytes_invalid=0 send_seq=813 receive_seq=813 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998743 adj=49996794 toolboard_t0: mcu_awake=0.069 mcu_task_avg=0.000095 mcu_task_stddev=0.000074 bytes_write=40044 bytes_read=1262483 bytes_retransmit=9 bytes_invalid=0 send_seq=5341 receive_seq=5341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997511 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14142 bytes_read=95131 bytes_retransmit=9 bytes_invalid=0 send_seq=1556 receive_seq=1556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000009 adj=63997342 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5209 bytes_read=179897 bytes_retransmit=9 bytes_invalid=0 send_seq=819 receive_seq=819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997502 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5803 bytes_read=17287 bytes_retransmit=9 bytes_invalid=0 send_seq=814 receive_seq=814 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48879 bytes_read=465275 bytes_retransmit=0 bytes_invalid=0 send_seq=4451 receive_seq=4451 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998550 coil_temp=17.5 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=47.4 th1: temp=46.9 th2: temp=47.6 th3: temp=45.6 sysload=0.07 cputime=88.855 memavail=7407600 print_time=746.910 buffer_time=1.079 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 724.4: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=7612640 bytes_read=963767 bytes_retransmit=9 bytes_invalid=0 send_seq=135064 receive_seq=135064 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=4827 freq=400015881 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5056 bytes_read=17608 bytes_retransmit=0 bytes_invalid=0 send_seq=814 receive_seq=814 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998746 adj=49996744 toolboard_t0: mcu_awake=0.069 mcu_task_avg=0.000095 mcu_task_stddev=0.000074 bytes_write=40120 bytes_read=1265569 bytes_retransmit=9 bytes_invalid=0 send_seq=5352 receive_seq=5352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997408 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14148 bytes_read=95259 bytes_retransmit=9 bytes_invalid=0 send_seq=1557 receive_seq=1557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000010 adj=63997292 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5215 bytes_read=180191 bytes_retransmit=9 bytes_invalid=0 send_seq=820 receive_seq=820 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997474 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5809 bytes_read=17303 bytes_retransmit=9 bytes_invalid=0 send_seq=815 receive_seq=815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999410 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48885 bytes_read=465631 bytes_retransmit=0 bytes_invalid=0 send_seq=4452 receive_seq=4452 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998581 coil_temp=17.5 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.6 th2: temp=47.7 th3: temp=45.8 sysload=0.07 cputime=88.981 memavail=7407600 print_time=747.986 buffer_time=1.155 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 725.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7625176 bytes_read=965158 bytes_retransmit=9 bytes_invalid=0 send_seq=135277 receive_seq=135277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=5755 freq=400015874 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5062 bytes_read=17624 bytes_retransmit=0 bytes_invalid=0 send_seq=815 receive_seq=815 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998748 adj=49996818 toolboard_t0: mcu_awake=0.069 mcu_task_avg=0.000095 mcu_task_stddev=0.000074 bytes_write=40196 bytes_read=1268628 bytes_retransmit=9 bytes_invalid=0 send_seq=5363 receive_seq=5363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997468 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14154 bytes_read=95359 bytes_retransmit=9 bytes_invalid=0 send_seq=1558 receive_seq=1558 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000010 adj=63997373 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5221 bytes_read=180425 bytes_retransmit=9 bytes_invalid=0 send_seq=821 receive_seq=821 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997542 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5815 bytes_read=17319 bytes_retransmit=9 bytes_invalid=0 send_seq=816 receive_seq=816 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999419 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=25.8  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48891 bytes_read=465987 bytes_retransmit=0 bytes_invalid=0 send_seq=4453 receive_seq=4453 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998601 coil_temp=17.5 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.6 th2: temp=47.5 th3: temp=45.7 sysload=0.07 cputime=89.107 memavail=7407360 print_time=749.063 buffer_time=1.231 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 726.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7637691 bytes_read=966553 bytes_retransmit=9 bytes_invalid=0 send_seq=135486 receive_seq=135486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=6677 freq=400015881 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5074 bytes_read=17656 bytes_retransmit=0 bytes_invalid=0 send_seq=817 receive_seq=817 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998754 adj=49996844 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40278 bytes_read=1271778 bytes_retransmit=9 bytes_invalid=0 send_seq=5375 receive_seq=5375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997498 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14166 bytes_read=95475 bytes_retransmit=9 bytes_invalid=0 send_seq=1560 receive_seq=1560 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000011 adj=63997416 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5233 bytes_read=180675 bytes_retransmit=9 bytes_invalid=0 send_seq=823 receive_seq=823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997576 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5827 bytes_read=17351 bytes_retransmit=9 bytes_invalid=0 send_seq=818 receive_seq=818 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48903 bytes_read=466359 bytes_retransmit=0 bytes_invalid=0 send_seq=4455 receive_seq=4455 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998612 coil_temp=17.5 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=47.7 th1: temp=46.7 th2: temp=47.6 th3: temp=45.8 sysload=0.06 cputime=89.236 memavail=7407360 print_time=750.139 buffer_time=1.307 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 727.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7650201 bytes_read=967918 bytes_retransmit=9 bytes_invalid=0 send_seq=135697 receive_seq=135697 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=7605 freq=400015867 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5080 bytes_read=17685 bytes_retransmit=0 bytes_invalid=0 send_seq=818 receive_seq=818 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998757 adj=49996904 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40347 bytes_read=1274841 bytes_retransmit=9 bytes_invalid=0 send_seq=5385 receive_seq=5385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997478 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14172 bytes_read=95617 bytes_retransmit=9 bytes_invalid=0 send_seq=1561 receive_seq=1561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000010 adj=63997430 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5239 bytes_read=180969 bytes_retransmit=9 bytes_invalid=0 send_seq=824 receive_seq=824 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997595 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5833 bytes_read=17378 bytes_retransmit=9 bytes_invalid=0 send_seq=819 receive_seq=819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999423 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48909 bytes_read=466715 bytes_retransmit=0 bytes_invalid=0 send_seq=4456 receive_seq=4456 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998593 coil_temp=17.5 refs=0 mcu_temp=20.81 supply_voltage=3.011 th0: temp=47.4 th1: temp=46.6 th2: temp=47.4 th3: temp=45.6 sysload=0.06 cputime=89.366 memavail=7407360 print_time=751.216 buffer_time=1.383 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 728.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7662716 bytes_read=969288 bytes_retransmit=9 bytes_invalid=0 send_seq=135909 receive_seq=135909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=8533 freq=400015850 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5086 bytes_read=17701 bytes_retransmit=0 bytes_invalid=0 send_seq=819 receive_seq=819 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998760 adj=49996939 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40423 bytes_read=1277898 bytes_retransmit=9 bytes_invalid=0 send_seq=5396 receive_seq=5396 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997537 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14178 bytes_read=95717 bytes_retransmit=9 bytes_invalid=0 send_seq=1562 receive_seq=1562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000013 adj=63997467 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5245 bytes_read=181218 bytes_retransmit=9 bytes_invalid=0 send_seq=825 receive_seq=825 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5839 bytes_read=17394 bytes_retransmit=9 bytes_invalid=0 send_seq=820 receive_seq=820 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=25.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48915 bytes_read=467071 bytes_retransmit=0 bytes_invalid=0 send_seq=4457 receive_seq=4457 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998636 coil_temp=17.5 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=47.8 th1: temp=46.7 th2: temp=47.5 th3: temp=45.6 sysload=0.06 cputime=89.491 memavail=7407360 print_time=752.292 buffer_time=1.459 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 729.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7675308 bytes_read=970702 bytes_retransmit=9 bytes_invalid=0 send_seq=136125 receive_seq=136125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=9461 freq=400015905 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5092 bytes_read=17717 bytes_retransmit=0 bytes_invalid=0 send_seq=820 receive_seq=820 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998765 adj=49996987 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40499 bytes_read=1280956 bytes_retransmit=9 bytes_invalid=0 send_seq=5407 receive_seq=5407 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997576 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14184 bytes_read=95817 bytes_retransmit=9 bytes_invalid=0 send_seq=1563 receive_seq=1563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000014 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5251 bytes_read=181452 bytes_retransmit=9 bytes_invalid=0 send_seq=826 receive_seq=826 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5845 bytes_read=17410 bytes_retransmit=9 bytes_invalid=0 send_seq=821 receive_seq=821 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=25.8  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48921 bytes_read=467427 bytes_retransmit=0 bytes_invalid=0 send_seq=4458 receive_seq=4458 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998666 coil_temp=17.5 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=47.4 th1: temp=46.7 th2: temp=47.6 th3: temp=45.8 sysload=0.06 cputime=89.623 memavail=7407360 print_time=753.369 buffer_time=1.535 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 730.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7688305 bytes_read=972123 bytes_retransmit=9 bytes_invalid=0 send_seq=136344 receive_seq=136344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=9941 freq=400015890 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5098 bytes_read=17733 bytes_retransmit=0 bytes_invalid=0 send_seq=821 receive_seq=821 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998767 adj=49996893 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40575 bytes_read=1284041 bytes_retransmit=9 bytes_invalid=0 send_seq=5418 receive_seq=5418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997436 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14190 bytes_read=95945 bytes_retransmit=9 bytes_invalid=0 send_seq=1564 receive_seq=1564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000014 adj=63997412 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5257 bytes_read=181746 bytes_retransmit=9 bytes_invalid=0 send_seq=827 receive_seq=827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997556 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5851 bytes_read=17426 bytes_retransmit=9 bytes_invalid=0 send_seq=822 receive_seq=822 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48927 bytes_read=467783 bytes_retransmit=0 bytes_invalid=0 send_seq=4459 receive_seq=4459 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998616 coil_temp=17.5 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=47.4 th1: temp=46.6 th2: temp=47.6 th3: temp=45.6 sysload=0.06 cputime=89.748 memavail=7407360 print_time=754.445 buffer_time=1.611 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 731.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7700833 bytes_read=973498 bytes_retransmit=9 bytes_invalid=0 send_seq=136557 receive_seq=136557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=10853 freq=400015876 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5104 bytes_read=17749 bytes_retransmit=0 bytes_invalid=0 send_seq=822 receive_seq=822 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998770 adj=49996926 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40651 bytes_read=1287114 bytes_retransmit=9 bytes_invalid=0 send_seq=5429 receive_seq=5429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997499 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14196 bytes_read=96045 bytes_retransmit=9 bytes_invalid=0 send_seq=1565 receive_seq=1565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000013 adj=63997458 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5263 bytes_read=181980 bytes_retransmit=9 bytes_invalid=0 send_seq=828 receive_seq=828 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997599 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5857 bytes_read=17442 bytes_retransmit=9 bytes_invalid=0 send_seq=823 receive_seq=823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48933 bytes_read=468139 bytes_retransmit=0 bytes_invalid=0 send_seq=4460 receive_seq=4460 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998635 coil_temp=17.5 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=47.4 th1: temp=46.4 th2: temp=47.6 th3: temp=45.8 sysload=0.06 cputime=89.869 memavail=7407360 print_time=755.521 buffer_time=1.687 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 732.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7713391 bytes_read=974892 bytes_retransmit=9 bytes_invalid=0 send_seq=136768 receive_seq=136768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=11781 freq=400015868 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5110 bytes_read=17778 bytes_retransmit=0 bytes_invalid=0 send_seq=823 receive_seq=823 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998773 adj=49996952 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40727 bytes_read=1290172 bytes_retransmit=9 bytes_invalid=0 send_seq=5440 receive_seq=5440 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997575 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14202 bytes_read=96159 bytes_retransmit=9 bytes_invalid=0 send_seq=1566 receive_seq=1566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000013 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5269 bytes_read=182214 bytes_retransmit=9 bytes_invalid=0 send_seq=829 receive_seq=829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997629 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5863 bytes_read=17469 bytes_retransmit=9 bytes_invalid=0 send_seq=824 receive_seq=824 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48939 bytes_read=468495 bytes_retransmit=0 bytes_invalid=0 send_seq=4461 receive_seq=4461 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998642 coil_temp=17.5 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=47.4 th1: temp=46.4 th2: temp=47.6 th3: temp=45.8 sysload=0.06 cputime=89.997 memavail=7407384 print_time=756.598 buffer_time=1.763 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 733.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7725895 bytes_read=976252 bytes_retransmit=9 bytes_invalid=0 send_seq=136978 receive_seq=136978 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=12702 freq=400015851 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5116 bytes_read=17794 bytes_retransmit=0 bytes_invalid=0 send_seq=824 receive_seq=824 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998776 adj=49996964 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40803 bytes_read=1293315 bytes_retransmit=9 bytes_invalid=0 send_seq=5451 receive_seq=5451 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997592 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14208 bytes_read=96287 bytes_retransmit=9 bytes_invalid=0 send_seq=1567 receive_seq=1567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000012 adj=63997499 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5275 bytes_read=182523 bytes_retransmit=9 bytes_invalid=0 send_seq=830 receive_seq=830 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5869 bytes_read=17485 bytes_retransmit=9 bytes_invalid=0 send_seq=825 receive_seq=825 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48945 bytes_read=468851 bytes_retransmit=0 bytes_invalid=0 send_seq=4462 receive_seq=4462 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998648 coil_temp=17.5 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.5 th2: temp=47.7 th3: temp=45.7 sysload=0.06 cputime=90.123 memavail=7407400 print_time=757.674 buffer_time=1.838 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 734.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7738467 bytes_read=977622 bytes_retransmit=9 bytes_invalid=0 send_seq=137190 receive_seq=137190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=13630 freq=400015865 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5122 bytes_read=17810 bytes_retransmit=0 bytes_invalid=0 send_seq=825 receive_seq=825 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998779 adj=49996993 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40879 bytes_read=1296371 bytes_retransmit=9 bytes_invalid=0 send_seq=5462 receive_seq=5462 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997649 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14214 bytes_read=96387 bytes_retransmit=9 bytes_invalid=0 send_seq=1568 receive_seq=1568 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000012 adj=63997526 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5281 bytes_read=182757 bytes_retransmit=9 bytes_invalid=0 send_seq=831 receive_seq=831 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5875 bytes_read=17501 bytes_retransmit=9 bytes_invalid=0 send_seq=826 receive_seq=826 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48951 bytes_read=469207 bytes_retransmit=0 bytes_invalid=0 send_seq=4463 receive_seq=4463 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998651 coil_temp=17.5 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=47.4 th1: temp=46.5 th2: temp=47.4 th3: temp=45.7 sysload=0.06 cputime=90.267 memavail=7408020 print_time=758.751 buffer_time=1.914 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 735.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7750964 bytes_read=979037 bytes_retransmit=9 bytes_invalid=0 send_seq=137402 receive_seq=137402 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=14558 freq=400015848 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5128 bytes_read=17826 bytes_retransmit=0 bytes_invalid=0 send_seq=826 receive_seq=826 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998782 adj=49996955 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40955 bytes_read=1299428 bytes_retransmit=9 bytes_invalid=0 send_seq=5473 receive_seq=5473 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997610 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14220 bytes_read=96487 bytes_retransmit=9 bytes_invalid=0 send_seq=1569 receive_seq=1569 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997477 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5287 bytes_read=182991 bytes_retransmit=9 bytes_invalid=0 send_seq=832 receive_seq=832 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5881 bytes_read=17517 bytes_retransmit=9 bytes_invalid=0 send_seq=827 receive_seq=827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48957 bytes_read=469563 bytes_retransmit=0 bytes_invalid=0 send_seq=4464 receive_seq=4464 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998621 coil_temp=17.5 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.6 th2: temp=47.7 th3: temp=45.8 sysload=0.06 cputime=90.399 memavail=7407556 print_time=759.827 buffer_time=1.990 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 736.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7763510 bytes_read=980422 bytes_retransmit=9 bytes_invalid=0 send_seq=137617 receive_seq=137617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=15486 freq=400015860 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5134 bytes_read=17842 bytes_retransmit=0 bytes_invalid=0 send_seq=827 receive_seq=827 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998787 adj=49996981 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=41031 bytes_read=1302529 bytes_retransmit=9 bytes_invalid=0 send_seq=5484 receive_seq=5484 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997643 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14226 bytes_read=96615 bytes_retransmit=9 bytes_invalid=0 send_seq=1570 receive_seq=1570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997622 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5293 bytes_read=183285 bytes_retransmit=9 bytes_invalid=0 send_seq=833 receive_seq=833 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5887 bytes_read=17533 bytes_retransmit=9 bytes_invalid=0 send_seq=828 receive_seq=828 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48963 bytes_read=469919 bytes_retransmit=0 bytes_invalid=0 send_seq=4465 receive_seq=4465 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998639 coil_temp=17.5 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.6 th2: temp=47.6 th3: temp=45.7 sysload=0.05 cputime=90.528 memavail=7407556 print_time=760.904 buffer_time=2.066 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 737.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7776458 bytes_read=981827 bytes_retransmit=9 bytes_invalid=0 send_seq=137836 receive_seq=137836 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=16049 freq=400015892 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=5140 bytes_read=17871 bytes_retransmit=0 bytes_invalid=0 send_seq=828 receive_seq=828 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998792 adj=49996976 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=41107 bytes_read=1305585 bytes_retransmit=9 bytes_invalid=0 send_seq=5495 receive_seq=5495 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997609 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14232 bytes_read=96729 bytes_retransmit=9 bytes_invalid=0 send_seq=1571 receive_seq=1571 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997561 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5299 bytes_read=183519 bytes_retransmit=9 bytes_invalid=0 send_seq=834 receive_seq=834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997634 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5893 bytes_read=17560 bytes_retransmit=9 bytes_invalid=0 send_seq=829 receive_seq=829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999485 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48969 bytes_read=470275 bytes_retransmit=0 bytes_invalid=0 send_seq=4466 receive_seq=4466 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998631 coil_temp=17.5 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=47.8 th1: temp=46.6 th2: temp=47.5 th3: temp=45.9 sysload=0.05 cputime=90.656 memavail=7407556 print_time=761.980 buffer_time=2.142 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 738.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7789071 bytes_read=983226 bytes_retransmit=9 bytes_invalid=0 send_seq=138048 receive_seq=138048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=26 upcoming_bytes=16894 freq=400015917 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=5146 bytes_read=17887 bytes_retransmit=0 bytes_invalid=0 send_seq=829 receive_seq=829 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998793 adj=49996947 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=41183 bytes_read=1308642 bytes_retransmit=9 bytes_invalid=0 send_seq=5506 receive_seq=5506 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997564 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14238 bytes_read=96829 bytes_retransmit=9 bytes_invalid=0 send_seq=1572 receive_seq=1572 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997477 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5305 bytes_read=183768 bytes_retransmit=9 bytes_invalid=0 send_seq=835 receive_seq=835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997591 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5899 bytes_read=17576 bytes_retransmit=9 bytes_invalid=0 send_seq=830 receive_seq=830 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48975 bytes_read=470631 bytes_retransmit=0 bytes_invalid=0 send_seq=4467 receive_seq=4467 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998591 coil_temp=17.5 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.7 th2: temp=47.7 th3: temp=45.8 sysload=0.05 cputime=90.786 memavail=7407556 print_time=763.057 buffer_time=2.218 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 739.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7801578 bytes_read=984596 bytes_retransmit=9 bytes_invalid=0 send_seq=138260 receive_seq=138260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=17822 freq=400015938 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=5152 bytes_read=17903 bytes_retransmit=0 bytes_invalid=0 send_seq=830 receive_seq=830 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998796 adj=49996900 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=41259 bytes_read=1311729 bytes_retransmit=9 bytes_invalid=0 send_seq=5517 receive_seq=5517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997573 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14244 bytes_read=96957 bytes_retransmit=9 bytes_invalid=0 send_seq=1573 receive_seq=1573 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997429 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5311 bytes_read=184062 bytes_retransmit=9 bytes_invalid=0 send_seq=836 receive_seq=836 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997562 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5905 bytes_read=17592 bytes_retransmit=9 bytes_invalid=0 send_seq=831 receive_seq=831 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48981 bytes_read=470987 bytes_retransmit=0 bytes_invalid=0 send_seq=4468 receive_seq=4468 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998576 coil_temp=17.5 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.5 th2: temp=47.6 th3: temp=46.0 sysload=0.05 cputime=90.916 memavail=7407556 print_time=764.133 buffer_time=2.294 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 740.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7814094 bytes_read=985920 bytes_retransmit=9 bytes_invalid=0 send_seq=138461 receive_seq=138461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=18727 freq=400015921 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=5158 bytes_read=17919 bytes_retransmit=0 bytes_invalid=0 send_seq=831 receive_seq=831 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998799 adj=49996879 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=41328 bytes_read=1314820 bytes_retransmit=9 bytes_invalid=0 send_seq=5527 receive_seq=5527 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997531 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14250 bytes_read=97057 bytes_retransmit=9 bytes_invalid=0 send_seq=1574 receive_seq=1574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997397 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5317 bytes_read=184296 bytes_retransmit=9 bytes_invalid=0 send_seq=837 receive_seq=837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997550 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5911 bytes_read=17608 bytes_retransmit=9 bytes_invalid=0 send_seq=832 receive_seq=832 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48987 bytes_read=471343 bytes_retransmit=0 bytes_invalid=0 send_seq=4469 receive_seq=4469 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998573 coil_temp=17.5 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=47.4 th1: temp=46.5 th2: temp=47.3 th3: temp=45.8 sysload=0.05 cputime=91.042 memavail=7407556 print_time=765.210 buffer_time=2.370 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 741.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7826587 bytes_read=987314 bytes_retransmit=9 bytes_invalid=0 send_seq=138672 receive_seq=138672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=19671 freq=400015906 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=5164 bytes_read=17935 bytes_retransmit=0 bytes_invalid=0 send_seq=832 receive_seq=832 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998802 adj=49996914 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=41404 bytes_read=1317893 bytes_retransmit=9 bytes_invalid=0 send_seq=5538 receive_seq=5538 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997653 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14256 bytes_read=97157 bytes_retransmit=9 bytes_invalid=0 send_seq=1575 receive_seq=1575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997431 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5323 bytes_read=184530 bytes_retransmit=9 bytes_invalid=0 send_seq=838 receive_seq=838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999532 adj=47997594 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5917 bytes_read=17624 bytes_retransmit=9 bytes_invalid=0 send_seq=833 receive_seq=833 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48993 bytes_read=471699 bytes_retransmit=0 bytes_invalid=0 send_seq=4470 receive_seq=4470 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998596 coil_temp=17.5 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.5 th2: temp=47.7 th3: temp=45.7 sysload=0.05 cputime=91.173 memavail=7407556 print_time=766.286 buffer_time=2.446 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 742.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7839163 bytes_read=988679 bytes_retransmit=9 bytes_invalid=0 send_seq=138883 receive_seq=138883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=20583 freq=400015888 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5170 bytes_read=17964 bytes_retransmit=0 bytes_invalid=0 send_seq=833 receive_seq=833 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998804 adj=49996945 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=41480 bytes_read=1320978 bytes_retransmit=9 bytes_invalid=0 send_seq=5549 receive_seq=5549 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997681 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14262 bytes_read=97299 bytes_retransmit=9 bytes_invalid=0 send_seq=1576 receive_seq=1576 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5329 bytes_read=184824 bytes_retransmit=9 bytes_invalid=0 send_seq=839 receive_seq=839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5923 bytes_read=17651 bytes_retransmit=9 bytes_invalid=0 send_seq=834 receive_seq=834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=48999 bytes_read=472055 bytes_retransmit=0 bytes_invalid=0 send_seq=4471 receive_seq=4471 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998609 coil_temp=17.5 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.4 th2: temp=47.6 th3: temp=45.7 sysload=0.05 cputime=91.302 memavail=7407556 print_time=767.363 buffer_time=2.522 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 743.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7851680 bytes_read=990059 bytes_retransmit=9 bytes_invalid=0 send_seq=139097 receive_seq=139097 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=15419 freq=400015891 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5176 bytes_read=17980 bytes_retransmit=0 bytes_invalid=0 send_seq=834 receive_seq=834 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998808 adj=49996972 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=41556 bytes_read=1324035 bytes_retransmit=9 bytes_invalid=0 send_seq=5560 receive_seq=5560 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997686 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14268 bytes_read=97399 bytes_retransmit=9 bytes_invalid=0 send_seq=1577 receive_seq=1577 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5335 bytes_read=185073 bytes_retransmit=9 bytes_invalid=0 send_seq=840 receive_seq=840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5929 bytes_read=17667 bytes_retransmit=9 bytes_invalid=0 send_seq=835 receive_seq=835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=25.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49005 bytes_read=472411 bytes_retransmit=0 bytes_invalid=0 send_seq=4472 receive_seq=4472 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998626 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.5 th2: temp=47.7 th3: temp=45.8 sysload=0.05 cputime=91.418 memavail=7407556 print_time=767.901 buffer_time=2.059 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 744.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7864558 bytes_read=991483 bytes_retransmit=9 bytes_invalid=0 send_seq=139314 receive_seq=139314 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=16049 freq=400015883 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5182 bytes_read=17996 bytes_retransmit=0 bytes_invalid=0 send_seq=835 receive_seq=835 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998809 adj=49997007 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=41632 bytes_read=1327092 bytes_retransmit=9 bytes_invalid=0 send_seq=5571 receive_seq=5571 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997661 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14274 bytes_read=97499 bytes_retransmit=9 bytes_invalid=0 send_seq=1578 receive_seq=1578 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997529 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5341 bytes_read=185307 bytes_retransmit=9 bytes_invalid=0 send_seq=841 receive_seq=841 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5935 bytes_read=17683 bytes_retransmit=9 bytes_invalid=0 send_seq=836 receive_seq=836 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49011 bytes_read=472767 bytes_retransmit=0 bytes_invalid=0 send_seq=4473 receive_seq=4473 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998622 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=47.7 th1: temp=46.3 th2: temp=47.7 th3: temp=45.8 sysload=0.05 cputime=91.546 memavail=7407556 print_time=768.977 buffer_time=2.136 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 745.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=7877270 bytes_read=992884 bytes_retransmit=9 bytes_invalid=0 send_seq=139529 receive_seq=139529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=16811 freq=400015867 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5188 bytes_read=18012 bytes_retransmit=0 bytes_invalid=0 send_seq=836 receive_seq=836 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998811 adj=49997017 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=41708 bytes_read=1330176 bytes_retransmit=9 bytes_invalid=0 send_seq=5582 receive_seq=5582 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997651 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14280 bytes_read=97627 bytes_retransmit=9 bytes_invalid=0 send_seq=1579 receive_seq=1579 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997526 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5347 bytes_read=185601 bytes_retransmit=9 bytes_invalid=0 send_seq=842 receive_seq=842 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5941 bytes_read=17699 bytes_retransmit=9 bytes_invalid=0 send_seq=837 receive_seq=837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49017 bytes_read=473123 bytes_retransmit=0 bytes_invalid=0 send_seq=4474 receive_seq=4474 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998634 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.5 th2: temp=47.6 th3: temp=46.0 sysload=0.05 cputime=91.676 memavail=7407344 print_time=770.054 buffer_time=2.212 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 746.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=7889784 bytes_read=994254 bytes_retransmit=9 bytes_invalid=0 send_seq=139741 receive_seq=139741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=17723 freq=400015848 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5194 bytes_read=18028 bytes_retransmit=0 bytes_invalid=0 send_seq=837 receive_seq=837 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998815 adj=49997020 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=41784 bytes_read=1333254 bytes_retransmit=9 bytes_invalid=0 send_seq=5593 receive_seq=5593 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997746 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14286 bytes_read=97727 bytes_retransmit=9 bytes_invalid=0 send_seq=1580 receive_seq=1580 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997543 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5353 bytes_read=185835 bytes_retransmit=9 bytes_invalid=0 send_seq=843 receive_seq=843 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997732 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5947 bytes_read=17715 bytes_retransmit=9 bytes_invalid=0 send_seq=838 receive_seq=838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49023 bytes_read=473479 bytes_retransmit=0 bytes_invalid=0 send_seq=4475 receive_seq=4475 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998655 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=47.4 th1: temp=46.6 th2: temp=47.6 th3: temp=45.8 sysload=0.04 cputime=91.806 memavail=7407492 print_time=771.130 buffer_time=2.288 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 747.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=7902327 bytes_read=995658 bytes_retransmit=9 bytes_invalid=0 send_seq=139954 receive_seq=139954 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=18661 freq=400015853 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5200 bytes_read=18057 bytes_retransmit=0 bytes_invalid=0 send_seq=838 receive_seq=838 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998817 adj=49997046 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=41860 bytes_read=1336310 bytes_retransmit=9 bytes_invalid=0 send_seq=5604 receive_seq=5604 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997747 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14292 bytes_read=97841 bytes_retransmit=9 bytes_invalid=0 send_seq=1581 receive_seq=1581 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997555 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5359 bytes_read=186069 bytes_retransmit=9 bytes_invalid=0 send_seq=844 receive_seq=844 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997731 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5953 bytes_read=17742 bytes_retransmit=9 bytes_invalid=0 send_seq=839 receive_seq=839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49029 bytes_read=473835 bytes_retransmit=0 bytes_invalid=0 send_seq=4476 receive_seq=4476 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998665 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=47.4 th1: temp=46.4 th2: temp=47.6 th3: temp=45.9 sysload=0.04 cputime=91.936 memavail=7407596 print_time=772.207 buffer_time=2.363 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 748.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=7914812 bytes_read=997023 bytes_retransmit=9 bytes_invalid=0 send_seq=140165 receive_seq=140165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=19589 freq=400015877 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5206 bytes_read=18073 bytes_retransmit=0 bytes_invalid=0 send_seq=839 receive_seq=839 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998820 adj=49997023 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=41936 bytes_read=1339453 bytes_retransmit=9 bytes_invalid=0 send_seq=5615 receive_seq=5615 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997697 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14298 bytes_read=97969 bytes_retransmit=9 bytes_invalid=0 send_seq=1582 receive_seq=1582 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997522 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=5365 bytes_read=186378 bytes_retransmit=9 bytes_invalid=0 send_seq=845 receive_seq=845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997707 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5959 bytes_read=17758 bytes_retransmit=9 bytes_invalid=0 send_seq=840 receive_seq=840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49035 bytes_read=474191 bytes_retransmit=0 bytes_invalid=0 send_seq=4477 receive_seq=4477 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998653 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.7 th2: temp=47.8 th3: temp=45.9 sysload=0.04 cputime=92.066 memavail=7407596 print_time=773.283 buffer_time=2.440 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 749.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=7927393 bytes_read=998393 bytes_retransmit=9 bytes_invalid=0 send_seq=140377 receive_seq=140377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=20500 freq=400015864 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5212 bytes_read=18089 bytes_retransmit=0 bytes_invalid=0 send_seq=840 receive_seq=840 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998826 adj=49996985 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=42012 bytes_read=1342512 bytes_retransmit=9 bytes_invalid=0 send_seq=5626 receive_seq=5626 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997659 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14304 bytes_read=98069 bytes_retransmit=9 bytes_invalid=0 send_seq=1583 receive_seq=1583 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997475 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=5371 bytes_read=186612 bytes_retransmit=9 bytes_invalid=0 send_seq=846 receive_seq=846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5965 bytes_read=17774 bytes_retransmit=9 bytes_invalid=0 send_seq=841 receive_seq=841 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49041 bytes_read=474547 bytes_retransmit=0 bytes_invalid=0 send_seq=4478 receive_seq=4478 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998628 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.5 th2: temp=47.8 th3: temp=45.9 sysload=0.04 cputime=92.209 memavail=7406876 print_time=774.360 buffer_time=2.516 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 750.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7939911 bytes_read=999811 bytes_retransmit=9 bytes_invalid=0 send_seq=140590 receive_seq=140590 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=15320 freq=400015852 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5218 bytes_read=18105 bytes_retransmit=0 bytes_invalid=0 send_seq=841 receive_seq=841 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998828 adj=49997033 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=42088 bytes_read=1345568 bytes_retransmit=9 bytes_invalid=0 send_seq=5637 receive_seq=5637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997664 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14310 bytes_read=98169 bytes_retransmit=9 bytes_invalid=0 send_seq=1584 receive_seq=1584 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997488 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=5377 bytes_read=186846 bytes_retransmit=9 bytes_invalid=0 send_seq=847 receive_seq=847 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5971 bytes_read=17790 bytes_retransmit=9 bytes_invalid=0 send_seq=842 receive_seq=842 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49047 bytes_read=474903 bytes_retransmit=0 bytes_invalid=0 send_seq=4479 receive_seq=4479 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998663 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.6 th2: temp=47.6 th3: temp=46.0 sysload=0.04 cputime=92.327 memavail=7406876 print_time=774.898 buffer_time=2.053 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 751.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7952678 bytes_read=1001173 bytes_retransmit=9 bytes_invalid=0 send_seq=140801 receive_seq=140801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=16049 freq=400015834 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5224 bytes_read=18121 bytes_retransmit=0 bytes_invalid=0 send_seq=842 receive_seq=842 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998832 adj=49997076 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=42164 bytes_read=1348671 bytes_retransmit=9 bytes_invalid=0 send_seq=5648 receive_seq=5648 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997752 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14316 bytes_read=98297 bytes_retransmit=9 bytes_invalid=0 send_seq=1585 receive_seq=1585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=5383 bytes_read=187140 bytes_retransmit=9 bytes_invalid=0 send_seq=848 receive_seq=848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999535 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5977 bytes_read=17806 bytes_retransmit=9 bytes_invalid=0 send_seq=843 receive_seq=843 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49053 bytes_read=475259 bytes_retransmit=0 bytes_invalid=0 send_seq=4480 receive_seq=4480 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998678 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.4 th2: temp=47.7 th3: temp=45.9 sysload=0.04 cputime=92.468 memavail=7400832 print_time=775.974 buffer_time=2.129 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 752.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7965461 bytes_read=1002563 bytes_retransmit=9 bytes_invalid=0 send_seq=141017 receive_seq=141017 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=16729 freq=400015832 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5230 bytes_read=18150 bytes_retransmit=0 bytes_invalid=0 send_seq=843 receive_seq=843 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998835 adj=49997118 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=42240 bytes_read=1351727 bytes_retransmit=9 bytes_invalid=0 send_seq=5659 receive_seq=5659 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997752 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14322 bytes_read=98397 bytes_retransmit=9 bytes_invalid=0 send_seq=1586 receive_seq=1586 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997541 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=5389 bytes_read=187374 bytes_retransmit=9 bytes_invalid=0 send_seq=849 receive_seq=849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999535 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5983 bytes_read=17833 bytes_retransmit=9 bytes_invalid=0 send_seq=844 receive_seq=844 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49059 bytes_read=475615 bytes_retransmit=0 bytes_invalid=0 send_seq=4481 receive_seq=4481 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998693 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.6 th2: temp=47.8 th3: temp=45.9 sysload=0.04 cputime=92.601 memavail=7408000 print_time=777.051 buffer_time=2.204 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 753.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7977978 bytes_read=1003957 bytes_retransmit=9 bytes_invalid=0 send_seq=141228 receive_seq=141228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=17657 freq=400015824 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5236 bytes_read=18166 bytes_retransmit=0 bytes_invalid=0 send_seq=844 receive_seq=844 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998837 adj=49997095 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=42316 bytes_read=1354783 bytes_retransmit=9 bytes_invalid=0 send_seq=5670 receive_seq=5670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997706 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14328 bytes_read=98511 bytes_retransmit=9 bytes_invalid=0 send_seq=1587 receive_seq=1587 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997542 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5395 bytes_read=187623 bytes_retransmit=9 bytes_invalid=0 send_seq=850 receive_seq=850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5989 bytes_read=17849 bytes_retransmit=9 bytes_invalid=0 send_seq=845 receive_seq=845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49065 bytes_read=475971 bytes_retransmit=0 bytes_invalid=0 send_seq=4482 receive_seq=4482 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998673 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=47.8 th1: temp=46.7 th2: temp=47.5 th3: temp=46.0 sysload=0.04 cputime=92.732 memavail=7408000 print_time=778.127 buffer_time=2.280 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 754.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=7990477 bytes_read=1005287 bytes_retransmit=9 bytes_invalid=0 send_seq=141432 receive_seq=141432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=18578 freq=400015799 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5242 bytes_read=18182 bytes_retransmit=0 bytes_invalid=0 send_seq=845 receive_seq=845 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998839 adj=49997080 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=42392 bytes_read=1357869 bytes_retransmit=9 bytes_invalid=0 send_seq=5681 receive_seq=5681 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997692 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14334 bytes_read=98639 bytes_retransmit=9 bytes_invalid=0 send_seq=1588 receive_seq=1588 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997545 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5401 bytes_read=187917 bytes_retransmit=9 bytes_invalid=0 send_seq=851 receive_seq=851 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=5995 bytes_read=17865 bytes_retransmit=9 bytes_invalid=0 send_seq=846 receive_seq=846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49071 bytes_read=476327 bytes_retransmit=0 bytes_invalid=0 send_seq=4483 receive_seq=4483 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998673 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.7 th2: temp=47.7 th3: temp=46.0 sysload=0.04 cputime=92.867 memavail=7408000 print_time=779.204 buffer_time=2.357 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 755.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=8003008 bytes_read=1006687 bytes_retransmit=9 bytes_invalid=0 send_seq=141644 receive_seq=141644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=19489 freq=400015800 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5248 bytes_read=18198 bytes_retransmit=0 bytes_invalid=0 send_seq=846 receive_seq=846 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998842 adj=49997097 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=42461 bytes_read=1360963 bytes_retransmit=9 bytes_invalid=0 send_seq=5691 receive_seq=5691 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997722 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14340 bytes_read=98739 bytes_retransmit=9 bytes_invalid=0 send_seq=1589 receive_seq=1589 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997629 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5407 bytes_read=188151 bytes_retransmit=9 bytes_invalid=0 send_seq=852 receive_seq=852 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997692 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6001 bytes_read=17881 bytes_retransmit=9 bytes_invalid=0 send_seq=847 receive_seq=847 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49077 bytes_read=476683 bytes_retransmit=0 bytes_invalid=0 send_seq=4484 receive_seq=4484 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998685 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.5 th2: temp=47.8 th3: temp=46.1 sysload=0.04 cputime=92.999 memavail=7407508 print_time=780.280 buffer_time=2.433 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 756.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=8015539 bytes_read=1008072 bytes_retransmit=9 bytes_invalid=0 send_seq=141856 receive_seq=141856 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=20401 freq=400015795 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5254 bytes_read=18214 bytes_retransmit=0 bytes_invalid=0 send_seq=847 receive_seq=847 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998846 adj=49997080 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=42537 bytes_read=1364040 bytes_retransmit=9 bytes_invalid=0 send_seq=5702 receive_seq=5702 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997692 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14346 bytes_read=98839 bytes_retransmit=9 bytes_invalid=0 send_seq=1590 receive_seq=1590 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997644 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5413 bytes_read=188385 bytes_retransmit=9 bytes_invalid=0 send_seq=853 receive_seq=853 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6007 bytes_read=17897 bytes_retransmit=9 bytes_invalid=0 send_seq=848 receive_seq=848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49083 bytes_read=477039 bytes_retransmit=0 bytes_invalid=0 send_seq=4485 receive_seq=4485 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998681 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=47.7 th1: temp=46.5 th2: temp=47.9 th3: temp=46.0 sysload=0.04 cputime=93.128 memavail=7407508 print_time=781.357 buffer_time=2.506 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 757.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=8028091 bytes_read=1009447 bytes_retransmit=9 bytes_invalid=0 send_seq=142069 receive_seq=142069 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=15204 freq=400015833 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5260 bytes_read=18243 bytes_retransmit=0 bytes_invalid=0 send_seq=848 receive_seq=848 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998853 adj=49997079 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=42613 bytes_read=1367125 bytes_retransmit=9 bytes_invalid=0 send_seq=5713 receive_seq=5713 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997750 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14352 bytes_read=98967 bytes_retransmit=9 bytes_invalid=0 send_seq=1591 receive_seq=1591 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997623 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5419 bytes_read=188679 bytes_retransmit=9 bytes_invalid=0 send_seq=854 receive_seq=854 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6013 bytes_read=17924 bytes_retransmit=9 bytes_invalid=0 send_seq=849 receive_seq=849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49089 bytes_read=477395 bytes_retransmit=0 bytes_invalid=0 send_seq=4486 receive_seq=4486 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998679 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.7 th2: temp=47.6 th3: temp=46.0 sysload=0.04 cputime=93.241 memavail=7407508 print_time=781.895 buffer_time=2.044 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 758.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=8040768 bytes_read=1010836 bytes_retransmit=9 bytes_invalid=0 send_seq=142282 receive_seq=142282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=16049 freq=400015819 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5266 bytes_read=18259 bytes_retransmit=0 bytes_invalid=0 send_seq=849 receive_seq=849 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998854 adj=49997105 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=42689 bytes_read=1370182 bytes_retransmit=9 bytes_invalid=0 send_seq=5724 receive_seq=5724 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997677 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14358 bytes_read=99081 bytes_retransmit=9 bytes_invalid=0 send_seq=1592 receive_seq=1592 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5425 bytes_read=188928 bytes_retransmit=9 bytes_invalid=0 send_seq=855 receive_seq=855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6019 bytes_read=17940 bytes_retransmit=9 bytes_invalid=0 send_seq=850 receive_seq=850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49095 bytes_read=477751 bytes_retransmit=0 bytes_invalid=0 send_seq=4487 receive_seq=4487 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998647 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.6 th2: temp=48.0 th3: temp=46.0 sysload=0.04 cputime=93.370 memavail=7407528 print_time=782.971 buffer_time=2.119 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 759.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=8053677 bytes_read=1012251 bytes_retransmit=9 bytes_invalid=0 send_seq=142500 receive_seq=142500 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=16596 freq=400015828 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5272 bytes_read=18275 bytes_retransmit=0 bytes_invalid=0 send_seq=850 receive_seq=850 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998858 adj=49997117 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=42765 bytes_read=1373238 bytes_retransmit=9 bytes_invalid=0 send_seq=5735 receive_seq=5735 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997691 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14364 bytes_read=99181 bytes_retransmit=9 bytes_invalid=0 send_seq=1593 receive_seq=1593 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997552 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5431 bytes_read=189162 bytes_retransmit=9 bytes_invalid=0 send_seq=856 receive_seq=856 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6025 bytes_read=17955 bytes_retransmit=9 bytes_invalid=0 send_seq=851 receive_seq=851 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49101 bytes_read=478107 bytes_retransmit=0 bytes_invalid=0 send_seq=4488 receive_seq=4488 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998658 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.6 th2: temp=47.8 th3: temp=46.2 sysload=0.04 cputime=93.499 memavail=7407528 print_time=784.048 buffer_time=2.195 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 760.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8066188 bytes_read=1013617 bytes_retransmit=9 bytes_invalid=0 send_seq=142708 receive_seq=142708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=17524 freq=400015845 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5278 bytes_read=18291 bytes_retransmit=0 bytes_invalid=0 send_seq=851 receive_seq=851 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998860 adj=49997091 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=42841 bytes_read=1376324 bytes_retransmit=9 bytes_invalid=0 send_seq=5746 receive_seq=5746 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997674 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14370 bytes_read=99309 bytes_retransmit=9 bytes_invalid=0 send_seq=1594 receive_seq=1594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5437 bytes_read=189456 bytes_retransmit=9 bytes_invalid=0 send_seq=857 receive_seq=857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6031 bytes_read=17970 bytes_retransmit=9 bytes_invalid=0 send_seq=852 receive_seq=852 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49107 bytes_read=478463 bytes_retransmit=0 bytes_invalid=0 send_seq=4489 receive_seq=4489 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998646 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=47.7 th1: temp=46.6 th2: temp=48.1 th3: temp=45.9 sysload=0.04 cputime=93.632 memavail=7407528 print_time=785.124 buffer_time=2.270 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 761.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8078729 bytes_read=1014993 bytes_retransmit=9 bytes_invalid=0 send_seq=142919 receive_seq=142919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=18429 freq=400015831 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5284 bytes_read=18307 bytes_retransmit=0 bytes_invalid=0 send_seq=852 receive_seq=852 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998863 adj=49997051 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=42917 bytes_read=1379457 bytes_retransmit=9 bytes_invalid=0 send_seq=5757 receive_seq=5757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997615 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14376 bytes_read=99409 bytes_retransmit=9 bytes_invalid=0 send_seq=1595 receive_seq=1595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997463 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5443 bytes_read=189690 bytes_retransmit=9 bytes_invalid=0 send_seq=858 receive_seq=858 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999535 adj=47997613 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6037 bytes_read=17985 bytes_retransmit=9 bytes_invalid=0 send_seq=853 receive_seq=853 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49113 bytes_read=478819 bytes_retransmit=0 bytes_invalid=0 send_seq=4490 receive_seq=4490 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998619 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.6 th2: temp=48.1 th3: temp=46.0 sysload=0.03 cputime=93.762 memavail=7407528 print_time=786.201 buffer_time=2.346 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 762.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8091260 bytes_read=1016376 bytes_retransmit=9 bytes_invalid=0 send_seq=143131 receive_seq=143131 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=19340 freq=400015822 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5290 bytes_read=18323 bytes_retransmit=0 bytes_invalid=0 send_seq=853 receive_seq=853 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998866 adj=49997071 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=42993 bytes_read=1382514 bytes_retransmit=9 bytes_invalid=0 send_seq=5768 receive_seq=5768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997632 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14382 bytes_read=99509 bytes_retransmit=9 bytes_invalid=0 send_seq=1596 receive_seq=1596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997497 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5449 bytes_read=189924 bytes_retransmit=9 bytes_invalid=0 send_seq=859 receive_seq=859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6043 bytes_read=18011 bytes_retransmit=9 bytes_invalid=0 send_seq=854 receive_seq=854 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49119 bytes_read=479172 bytes_retransmit=0 bytes_invalid=0 send_seq=4491 receive_seq=4491 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998630 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.6 th2: temp=47.8 th3: temp=46.1 sysload=0.03 cputime=93.890 memavail=7407528 print_time=787.277 buffer_time=2.420 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 763.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8103847 bytes_read=1017751 bytes_retransmit=9 bytes_invalid=0 send_seq=143344 receive_seq=143344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=20235 freq=400015811 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5296 bytes_read=18352 bytes_retransmit=0 bytes_invalid=0 send_seq=854 receive_seq=854 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998868 adj=49997071 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43069 bytes_read=1385598 bytes_retransmit=9 bytes_invalid=0 send_seq=5779 receive_seq=5779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997702 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14388 bytes_read=99651 bytes_retransmit=9 bytes_invalid=0 send_seq=1597 receive_seq=1597 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5455 bytes_read=190233 bytes_retransmit=9 bytes_invalid=0 send_seq=860 receive_seq=860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6049 bytes_read=18026 bytes_retransmit=9 bytes_invalid=0 send_seq=855 receive_seq=855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49125 bytes_read=479517 bytes_retransmit=0 bytes_invalid=0 send_seq=4492 receive_seq=4492 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998638 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.6 th2: temp=48.0 th3: temp=46.2 sysload=0.03 cputime=94.017 memavail=7407528 print_time=788.354 buffer_time=2.493 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 764.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8116414 bytes_read=1019155 bytes_retransmit=9 bytes_invalid=0 send_seq=143557 receive_seq=143557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=15055 freq=400015812 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5302 bytes_read=18368 bytes_retransmit=0 bytes_invalid=0 send_seq=855 receive_seq=855 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998870 adj=49997074 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43145 bytes_read=1388657 bytes_retransmit=9 bytes_invalid=0 send_seq=5790 receive_seq=5790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997716 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14394 bytes_read=99751 bytes_retransmit=9 bytes_invalid=0 send_seq=1598 receive_seq=1598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997508 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5461 bytes_read=190467 bytes_retransmit=9 bytes_invalid=0 send_seq=861 receive_seq=861 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6055 bytes_read=18041 bytes_retransmit=9 bytes_invalid=0 send_seq=856 receive_seq=856 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49131 bytes_read=479862 bytes_retransmit=0 bytes_invalid=0 send_seq=4493 receive_seq=4493 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998674 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.8 th2: temp=47.9 th3: temp=46.0 sysload=0.03 cputime=94.132 memavail=7407528 print_time=788.892 buffer_time=2.031 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 765.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8128930 bytes_read=1020521 bytes_retransmit=9 bytes_invalid=0 send_seq=143766 receive_seq=143765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=15983 freq=400015819 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5308 bytes_read=18384 bytes_retransmit=0 bytes_invalid=0 send_seq=856 receive_seq=856 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998872 adj=49997098 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43221 bytes_read=1391715 bytes_retransmit=9 bytes_invalid=0 send_seq=5801 receive_seq=5801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997780 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14400 bytes_read=99851 bytes_retransmit=9 bytes_invalid=0 send_seq=1599 receive_seq=1599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5467 bytes_read=190701 bytes_retransmit=9 bytes_invalid=0 send_seq=862 receive_seq=862 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6061 bytes_read=18056 bytes_retransmit=9 bytes_invalid=0 send_seq=857 receive_seq=857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49137 bytes_read=480207 bytes_retransmit=0 bytes_invalid=0 send_seq=4494 receive_seq=4494 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998674 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=47.8 th1: temp=46.7 th2: temp=47.9 th3: temp=45.8 sysload=0.03 cputime=94.265 memavail=7407084 print_time=789.968 buffer_time=2.107 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 766.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8141903 bytes_read=1021931 bytes_retransmit=9 bytes_invalid=0 send_seq=143985 receive_seq=143985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=16463 freq=400015815 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5314 bytes_read=18400 bytes_retransmit=0 bytes_invalid=0 send_seq=857 receive_seq=857 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998875 adj=49997084 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43297 bytes_read=1394818 bytes_retransmit=9 bytes_invalid=0 send_seq=5812 receive_seq=5812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997738 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14406 bytes_read=99979 bytes_retransmit=9 bytes_invalid=0 send_seq=1600 receive_seq=1600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5473 bytes_read=190995 bytes_retransmit=9 bytes_invalid=0 send_seq=863 receive_seq=863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6067 bytes_read=18071 bytes_retransmit=9 bytes_invalid=0 send_seq=858 receive_seq=858 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49143 bytes_read=480552 bytes_retransmit=0 bytes_invalid=0 send_seq=4495 receive_seq=4495 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998687 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.9 th2: temp=48.0 th3: temp=46.1 sysload=0.03 cputime=94.398 memavail=7407084 print_time=791.045 buffer_time=2.183 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 767.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8154434 bytes_read=1023330 bytes_retransmit=9 bytes_invalid=0 send_seq=144197 receive_seq=144197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=17391 freq=400015808 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5320 bytes_read=18416 bytes_retransmit=0 bytes_invalid=0 send_seq=858 receive_seq=858 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998877 adj=49997082 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43366 bytes_read=1397911 bytes_retransmit=9 bytes_invalid=0 send_seq=5822 receive_seq=5822 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997711 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14412 bytes_read=100079 bytes_retransmit=9 bytes_invalid=0 send_seq=1601 receive_seq=1601 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5479 bytes_read=191229 bytes_retransmit=9 bytes_invalid=0 send_seq=864 receive_seq=864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6073 bytes_read=18097 bytes_retransmit=9 bytes_invalid=0 send_seq=859 receive_seq=859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49149 bytes_read=480897 bytes_retransmit=0 bytes_invalid=0 send_seq=4496 receive_seq=4496 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998674 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.5 th2: temp=48.2 th3: temp=46.1 sysload=0.03 cputime=94.529 memavail=7407108 print_time=792.121 buffer_time=2.259 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 768.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8167021 bytes_read=1024695 bytes_retransmit=9 bytes_invalid=0 send_seq=144408 receive_seq=144408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=18301 freq=400015806 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5326 bytes_read=18445 bytes_retransmit=0 bytes_invalid=0 send_seq=859 receive_seq=859 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998880 adj=49997079 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43442 bytes_read=1400969 bytes_retransmit=9 bytes_invalid=0 send_seq=5833 receive_seq=5833 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997690 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14418 bytes_read=100193 bytes_retransmit=9 bytes_invalid=0 send_seq=1602 receive_seq=1602 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997481 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5485 bytes_read=191478 bytes_retransmit=9 bytes_invalid=0 send_seq=865 receive_seq=865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997707 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6079 bytes_read=18112 bytes_retransmit=9 bytes_invalid=0 send_seq=860 receive_seq=860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49155 bytes_read=481242 bytes_retransmit=0 bytes_invalid=0 send_seq=4497 receive_seq=4497 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998663 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=47.4 th1: temp=46.9 th2: temp=47.8 th3: temp=46.0 sysload=0.03 cputime=94.666 memavail=7402320 print_time=793.198 buffer_time=2.335 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 769.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8179522 bytes_read=1026025 bytes_retransmit=9 bytes_invalid=0 send_seq=144613 receive_seq=144612 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=19224 freq=400015800 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5332 bytes_read=18461 bytes_retransmit=0 bytes_invalid=0 send_seq=860 receive_seq=860 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998883 adj=49997073 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43518 bytes_read=1404053 bytes_retransmit=9 bytes_invalid=0 send_seq=5844 receive_seq=5844 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997736 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14424 bytes_read=100321 bytes_retransmit=9 bytes_invalid=0 send_seq=1603 receive_seq=1603 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997489 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5491 bytes_read=191772 bytes_retransmit=9 bytes_invalid=0 send_seq=866 receive_seq=866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997707 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6085 bytes_read=18127 bytes_retransmit=9 bytes_invalid=0 send_seq=861 receive_seq=861 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49161 bytes_read=481587 bytes_retransmit=0 bytes_invalid=0 send_seq=4498 receive_seq=4498 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998652 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.7 th2: temp=48.1 th3: temp=46.0 sysload=0.03 cputime=94.804 memavail=7408244 print_time=794.274 buffer_time=2.411 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Stats 770.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8192048 bytes_read=1027435 bytes_retransmit=9 bytes_invalid=0 send_seq=144824 receive_seq=144823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=20152 freq=400015802 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5338 bytes_read=18477 bytes_retransmit=0 bytes_invalid=0 send_seq=861 receive_seq=861 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998886 adj=49997084 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43594 bytes_read=1407110 bytes_retransmit=9 bytes_invalid=0 send_seq=5855 receive_seq=5855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997706 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14430 bytes_read=100421 bytes_retransmit=9 bytes_invalid=0 send_seq=1604 receive_seq=1604 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997560 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5497 bytes_read=192006 bytes_retransmit=9 bytes_invalid=0 send_seq=867 receive_seq=867 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997702 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6091 bytes_read=18142 bytes_retransmit=9 bytes_invalid=0 send_seq=862 receive_seq=862 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49167 bytes_read=481932 bytes_retransmit=0 bytes_invalid=0 send_seq=4499 receive_seq=4499 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998651 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=47.7 th1: temp=46.7 th2: temp=48.0 th3: temp=45.9 sysload=0.03 cputime=94.933 memavail=7408244 print_time=795.351 buffer_time=2.487 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 771.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8204579 bytes_read=1028810 bytes_retransmit=9 bytes_invalid=0 send_seq=145036 receive_seq=145036 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=14972 freq=400015808 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5344 bytes_read=18493 bytes_retransmit=0 bytes_invalid=0 send_seq=862 receive_seq=862 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998888 adj=49997068 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43670 bytes_read=1410184 bytes_retransmit=9 bytes_invalid=0 send_seq=5866 receive_seq=5866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997682 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14436 bytes_read=100521 bytes_retransmit=9 bytes_invalid=0 send_seq=1605 receive_seq=1605 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997530 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5503 bytes_read=192240 bytes_retransmit=9 bytes_invalid=0 send_seq=868 receive_seq=868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997754 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6097 bytes_read=18157 bytes_retransmit=9 bytes_invalid=0 send_seq=863 receive_seq=863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49173 bytes_read=482287 bytes_retransmit=0 bytes_invalid=0 send_seq=4500 receive_seq=4500 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998643 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=47.8 th1: temp=46.7 th2: temp=47.8 th3: temp=46.2 sysload=0.03 cputime=95.049 memavail=7408244 print_time=795.889 buffer_time=2.025 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 772.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8217041 bytes_read=1030166 bytes_retransmit=9 bytes_invalid=0 send_seq=145246 receive_seq=145246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=15917 freq=400015792 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5350 bytes_read=18509 bytes_retransmit=0 bytes_invalid=0 send_seq=863 receive_seq=863 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998890 adj=49997092 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43746 bytes_read=1413268 bytes_retransmit=9 bytes_invalid=0 send_seq=5877 receive_seq=5877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997650 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14442 bytes_read=100649 bytes_retransmit=9 bytes_invalid=0 send_seq=1606 receive_seq=1606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997514 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5509 bytes_read=192534 bytes_retransmit=9 bytes_invalid=0 send_seq=869 receive_seq=869 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997801 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6103 bytes_read=18183 bytes_retransmit=9 bytes_invalid=0 send_seq=864 receive_seq=864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49179 bytes_read=482643 bytes_retransmit=0 bytes_invalid=0 send_seq=4501 receive_seq=4501 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998639 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.6 th2: temp=48.0 th3: temp=46.4 sysload=0.03 cputime=95.179 memavail=7408244 print_time=796.965 buffer_time=2.101 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for x axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 773.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8230076 bytes_read=1031605 bytes_retransmit=9 bytes_invalid=0 send_seq=145466 receive_seq=145466 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=16381 freq=400015792 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5356 bytes_read=18538 bytes_retransmit=0 bytes_invalid=0 send_seq=864 receive_seq=864 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998893 adj=49997120 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43822 bytes_read=1416324 bytes_retransmit=9 bytes_invalid=0 send_seq=5888 receive_seq=5888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997658 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14448 bytes_read=100763 bytes_retransmit=9 bytes_invalid=0 send_seq=1607 receive_seq=1607 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=5515 bytes_read=192783 bytes_retransmit=9 bytes_invalid=0 send_seq=870 receive_seq=870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997789 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6109 bytes_read=18198 bytes_retransmit=9 bytes_invalid=0 send_seq=865 receive_seq=865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49185 bytes_read=482999 bytes_retransmit=0 bytes_invalid=0 send_seq=4502 receive_seq=4502 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998650 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.7 th2: temp=48.0 th3: temp=46.2 sysload=0.03 cputime=95.308 memavail=7408244 print_time=798.042 buffer_time=2.177 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 774.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8242597 bytes_read=1032965 bytes_retransmit=9 bytes_invalid=0 send_seq=145676 receive_seq=145676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=29528 freq=400015796 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5362 bytes_read=18554 bytes_retransmit=0 bytes_invalid=0 send_seq=865 receive_seq=865 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998897 adj=49997102 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43898 bytes_read=1419382 bytes_retransmit=9 bytes_invalid=0 send_seq=5899 receive_seq=5899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997635 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14454 bytes_read=100863 bytes_retransmit=9 bytes_invalid=0 send_seq=1608 receive_seq=1608 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=5521 bytes_read=193017 bytes_retransmit=9 bytes_invalid=0 send_seq=871 receive_seq=871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997813 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6115 bytes_read=18213 bytes_retransmit=9 bytes_invalid=0 send_seq=866 receive_seq=866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49191 bytes_read=483355 bytes_retransmit=0 bytes_invalid=0 send_seq=4503 receive_seq=4503 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998647 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.7 th2: temp=47.8 th3: temp=46.2 sysload=0.03 cputime=95.443 memavail=7408244 print_time=799.118 buffer_time=2.254 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 775.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8255173 bytes_read=1034356 bytes_retransmit=9 bytes_invalid=0 send_seq=145889 receive_seq=145889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=42651 freq=400015788 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5368 bytes_read=18570 bytes_retransmit=0 bytes_invalid=0 send_seq=866 receive_seq=866 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998899 adj=49997102 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43974 bytes_read=1422527 bytes_retransmit=9 bytes_invalid=0 send_seq=5910 receive_seq=5910 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997613 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14460 bytes_read=100991 bytes_retransmit=9 bytes_invalid=0 send_seq=1609 receive_seq=1609 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997488 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=5527 bytes_read=193311 bytes_retransmit=9 bytes_invalid=0 send_seq=872 receive_seq=872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997750 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6121 bytes_read=18228 bytes_retransmit=9 bytes_invalid=0 send_seq=867 receive_seq=867 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49197 bytes_read=483711 bytes_retransmit=0 bytes_invalid=0 send_seq=4504 receive_seq=4504 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998637 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.0 th2: temp=48.0 th3: temp=46.3 sysload=0.03 cputime=95.579 memavail=7406992 print_time=800.195 buffer_time=2.329 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 776.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8277571 bytes_read=1036540 bytes_retransmit=9 bytes_invalid=0 send_seq=146258 receive_seq=146258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=46692 freq=400015776 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5374 bytes_read=18586 bytes_retransmit=0 bytes_invalid=0 send_seq=867 receive_seq=867 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998901 adj=49997099 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44050 bytes_read=1425600 bytes_retransmit=9 bytes_invalid=0 send_seq=5921 receive_seq=5921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997638 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14466 bytes_read=101091 bytes_retransmit=9 bytes_invalid=0 send_seq=1610 receive_seq=1610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997497 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=5533 bytes_read=193545 bytes_retransmit=9 bytes_invalid=0 send_seq=873 receive_seq=873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997721 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6127 bytes_read=18243 bytes_retransmit=9 bytes_invalid=0 send_seq=868 receive_seq=868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49203 bytes_read=484067 bytes_retransmit=0 bytes_invalid=0 send_seq=4505 receive_seq=4505 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998648 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=47.4 th1: temp=46.7 th2: temp=48.0 th3: temp=46.4 sysload=0.03 cputime=95.725 memavail=7406992 print_time=801.271 buffer_time=2.406 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 777.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8302364 bytes_read=1038875 bytes_retransmit=9 bytes_invalid=0 send_seq=146663 receive_seq=146663 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=48548 freq=400015774 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5380 bytes_read=18602 bytes_retransmit=0 bytes_invalid=0 send_seq=868 receive_seq=868 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998903 adj=49997099 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44126 bytes_read=1428656 bytes_retransmit=9 bytes_invalid=0 send_seq=5932 receive_seq=5932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997646 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14472 bytes_read=101191 bytes_retransmit=9 bytes_invalid=0 send_seq=1611 receive_seq=1611 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997526 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=5539 bytes_read=193779 bytes_retransmit=9 bytes_invalid=0 send_seq=874 receive_seq=874 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997727 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6133 bytes_read=18269 bytes_retransmit=9 bytes_invalid=0 send_seq=869 receive_seq=869 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49209 bytes_read=484423 bytes_retransmit=0 bytes_invalid=0 send_seq=4506 receive_seq=4506 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998705 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=47.7 th1: temp=46.8 th2: temp=47.9 th3: temp=46.4 sysload=0.03 cputime=95.871 memavail=7406992 print_time=802.348 buffer_time=2.481 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 778.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8327167 bytes_read=1041215 bytes_retransmit=9 bytes_invalid=0 send_seq=147069 receive_seq=147069 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=38175 freq=400015757 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5386 bytes_read=18631 bytes_retransmit=0 bytes_invalid=0 send_seq=869 receive_seq=869 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998904 adj=49997089 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44195 bytes_read=1431718 bytes_retransmit=9 bytes_invalid=0 send_seq=5942 receive_seq=5942 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997639 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14478 bytes_read=101333 bytes_retransmit=9 bytes_invalid=0 send_seq=1612 receive_seq=1612 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997518 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5545 bytes_read=194088 bytes_retransmit=9 bytes_invalid=0 send_seq=875 receive_seq=875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997698 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6139 bytes_read=18284 bytes_retransmit=9 bytes_invalid=0 send_seq=870 receive_seq=870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49215 bytes_read=484779 bytes_retransmit=0 bytes_invalid=0 send_seq=4507 receive_seq=4507 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998690 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.6 th2: temp=47.7 th3: temp=46.0 sysload=0.03 cputime=96.000 memavail=7406992 print_time=802.886 buffer_time=2.018 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 779.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8351956 bytes_read=1043584 bytes_retransmit=9 bytes_invalid=0 send_seq=147475 receive_seq=147475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=40031 freq=400015785 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5392 bytes_read=18647 bytes_retransmit=0 bytes_invalid=0 send_seq=870 receive_seq=870 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998907 adj=49997136 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44271 bytes_read=1434775 bytes_retransmit=9 bytes_invalid=0 send_seq=5953 receive_seq=5953 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997671 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14484 bytes_read=101433 bytes_retransmit=9 bytes_invalid=0 send_seq=1613 receive_seq=1613 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000018 adj=63997535 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5551 bytes_read=194322 bytes_retransmit=9 bytes_invalid=0 send_seq=876 receive_seq=876 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997739 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6145 bytes_read=18299 bytes_retransmit=9 bytes_invalid=0 send_seq=871 receive_seq=871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49221 bytes_read=485135 bytes_retransmit=0 bytes_invalid=0 send_seq=4508 receive_seq=4508 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998696 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.1 th2: temp=48.1 th3: temp=46.3 sysload=0.03 cputime=96.145 memavail=7406992 print_time=803.963 buffer_time=2.095 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 780.4: gcodein=0  mcu: mcu_awake=0.019 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8377726 bytes_read=1046010 bytes_retransmit=9 bytes_invalid=0 send_seq=147895 receive_seq=147895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=40990 freq=400015789 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5398 bytes_read=18663 bytes_retransmit=0 bytes_invalid=0 send_seq=871 receive_seq=871 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998909 adj=49997098 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44347 bytes_read=1437833 bytes_retransmit=9 bytes_invalid=0 send_seq=5964 receive_seq=5964 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000181 adj=63997598 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14490 bytes_read=101533 bytes_retransmit=9 bytes_invalid=0 send_seq=1614 receive_seq=1614 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000018 adj=63997462 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5557 bytes_read=194556 bytes_retransmit=9 bytes_invalid=0 send_seq=877 receive_seq=877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6151 bytes_read=18314 bytes_retransmit=9 bytes_invalid=0 send_seq=872 receive_seq=872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49227 bytes_read=485491 bytes_retransmit=0 bytes_invalid=0 send_seq=4509 receive_seq=4509 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998676 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.8 th2: temp=48.2 th3: temp=46.4 sysload=0.03 cputime=96.294 memavail=7406992 print_time=805.039 buffer_time=2.171 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 781.4: gcodein=0  mcu: mcu_awake=0.019 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8402505 bytes_read=1048340 bytes_retransmit=9 bytes_invalid=0 send_seq=148299 receive_seq=148299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=42815 freq=400015783 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5404 bytes_read=18679 bytes_retransmit=0 bytes_invalid=0 send_seq=872 receive_seq=872 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998911 adj=49997084 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44423 bytes_read=1440933 bytes_retransmit=9 bytes_invalid=0 send_seq=5975 receive_seq=5975 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000181 adj=63997594 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14496 bytes_read=101659 bytes_retransmit=9 bytes_invalid=0 send_seq=1615 receive_seq=1615 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000017 adj=63997453 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5563 bytes_read=194839 bytes_retransmit=9 bytes_invalid=0 send_seq=878 receive_seq=878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6157 bytes_read=18329 bytes_retransmit=9 bytes_invalid=0 send_seq=873 receive_seq=873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49233 bytes_read=485847 bytes_retransmit=0 bytes_invalid=0 send_seq=4510 receive_seq=4510 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998660 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=47.8 th1: temp=46.8 th2: temp=48.2 th3: temp=46.3 sysload=0.02 cputime=96.440 memavail=7406992 print_time=806.115 buffer_time=2.246 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 782.4: gcodein=0  mcu: mcu_awake=0.019 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8427316 bytes_read=1050712 bytes_retransmit=9 bytes_invalid=0 send_seq=148706 receive_seq=148706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=44671 freq=400015777 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5410 bytes_read=18694 bytes_retransmit=0 bytes_invalid=0 send_seq=873 receive_seq=873 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998914 adj=49997083 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44499 bytes_read=1444030 bytes_retransmit=9 bytes_invalid=0 send_seq=5986 receive_seq=5986 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997621 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14502 bytes_read=101752 bytes_retransmit=9 bytes_invalid=0 send_seq=1616 receive_seq=1616 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000016 adj=63997462 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5569 bytes_read=195055 bytes_retransmit=9 bytes_invalid=0 send_seq=879 receive_seq=879 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6163 bytes_read=18356 bytes_retransmit=9 bytes_invalid=0 send_seq=874 receive_seq=874 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49239 bytes_read=486203 bytes_retransmit=0 bytes_invalid=0 send_seq=4511 receive_seq=4511 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998661 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.7 th2: temp=48.1 th3: temp=46.2 sysload=0.02 cputime=96.583 memavail=7406992 print_time=807.192 buffer_time=2.322 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 783.4: gcodein=0  mcu: mcu_awake=0.019 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8452182 bytes_read=1053068 bytes_retransmit=9 bytes_invalid=0 send_seq=149116 receive_seq=149116 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=46460 freq=400015761 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5416 bytes_read=18722 bytes_retransmit=0 bytes_invalid=0 send_seq=874 receive_seq=874 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998916 adj=49997088 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44575 bytes_read=1447070 bytes_retransmit=9 bytes_invalid=0 send_seq=5997 receive_seq=5997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000181 adj=63997627 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14508 bytes_read=101858 bytes_retransmit=9 bytes_invalid=0 send_seq=1617 receive_seq=1617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000017 adj=63997468 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5575 bytes_read=195287 bytes_retransmit=9 bytes_invalid=0 send_seq=880 receive_seq=880 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6169 bytes_read=18372 bytes_retransmit=9 bytes_invalid=0 send_seq=875 receive_seq=875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999439 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49245 bytes_read=486559 bytes_retransmit=0 bytes_invalid=0 send_seq=4512 receive_seq=4512 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998657 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=47.1 th1: temp=47.0 th2: temp=48.3 th3: temp=46.4 sysload=0.02 cputime=96.735 memavail=7407020 print_time=808.268 buffer_time=2.397 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 784.4: gcodein=0  mcu: mcu_awake=0.019 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8477024 bytes_read=1055418 bytes_retransmit=9 bytes_invalid=0 send_seq=149524 receive_seq=149524 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=48316 freq=400015830 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5422 bytes_read=18737 bytes_retransmit=0 bytes_invalid=0 send_seq=875 receive_seq=875 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998917 adj=49997106 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44651 bytes_read=1450136 bytes_retransmit=9 bytes_invalid=0 send_seq=6008 receive_seq=6008 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997675 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14514 bytes_read=101977 bytes_retransmit=9 bytes_invalid=0 send_seq=1618 receive_seq=1618 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000017 adj=63997517 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5581 bytes_read=195561 bytes_retransmit=9 bytes_invalid=0 send_seq=881 receive_seq=881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6175 bytes_read=18388 bytes_retransmit=9 bytes_invalid=0 send_seq=876 receive_seq=876 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49251 bytes_read=486915 bytes_retransmit=0 bytes_invalid=0 send_seq=4513 receive_seq=4513 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998667 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=47.8 th1: temp=46.8 th2: temp=48.3 th3: temp=46.3 sysload=0.02 cputime=96.884 memavail=7407048 print_time=809.345 buffer_time=2.473 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 785.4: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8501771 bytes_read=1057798 bytes_retransmit=9 bytes_invalid=0 send_seq=149929 receive_seq=149929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=37943 freq=400015825 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5428 bytes_read=18752 bytes_retransmit=0 bytes_invalid=0 send_seq=876 receive_seq=876 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998920 adj=49996993 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44727 bytes_read=1453176 bytes_retransmit=9 bytes_invalid=0 send_seq=6019 receive_seq=6019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997869 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14520 bytes_read=102070 bytes_retransmit=9 bytes_invalid=0 send_seq=1619 receive_seq=1619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997393 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5587 bytes_read=195779 bytes_retransmit=9 bytes_invalid=0 send_seq=882 receive_seq=882 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997581 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6181 bytes_read=18404 bytes_retransmit=9 bytes_invalid=0 send_seq=877 receive_seq=877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49257 bytes_read=487255 bytes_retransmit=0 bytes_invalid=0 send_seq=4514 receive_seq=4514 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998598 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.0 th2: temp=48.3 th3: temp=46.4 sysload=0.02 cputime=97.020 memavail=7407048 print_time=809.883 buffer_time=2.011 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 786.4: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8526572 bytes_read=1060133 bytes_retransmit=9 bytes_invalid=0 send_seq=150334 receive_seq=150334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=39799 freq=400015825 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5434 bytes_read=18767 bytes_retransmit=0 bytes_invalid=0 send_seq=877 receive_seq=877 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998923 adj=49997034 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44803 bytes_read=1456246 bytes_retransmit=9 bytes_invalid=0 send_seq=6030 receive_seq=6030 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997842 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14526 bytes_read=102169 bytes_retransmit=9 bytes_invalid=0 send_seq=1620 receive_seq=1620 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997425 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5593 bytes_read=195997 bytes_retransmit=9 bytes_invalid=0 send_seq=883 receive_seq=883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997611 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6187 bytes_read=18420 bytes_retransmit=9 bytes_invalid=0 send_seq=878 receive_seq=878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49263 bytes_read=487611 bytes_retransmit=0 bytes_invalid=0 send_seq=4515 receive_seq=4515 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998597 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=47.7 th1: temp=46.8 th2: temp=48.3 th3: temp=46.3 sysload=0.10 cputime=97.179 memavail=7407648 print_time=810.960 buffer_time=2.086 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 787.4: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8552357 bytes_read=1062558 bytes_retransmit=9 bytes_invalid=0 send_seq=150757 receive_seq=150757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=40758 freq=400015819 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5440 bytes_read=18783 bytes_retransmit=0 bytes_invalid=0 send_seq=878 receive_seq=878 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998925 adj=49997057 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44879 bytes_read=1459330 bytes_retransmit=9 bytes_invalid=0 send_seq=6041 receive_seq=6041 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997787 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14532 bytes_read=102297 bytes_retransmit=9 bytes_invalid=0 send_seq=1621 receive_seq=1621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997487 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5599 bytes_read=196290 bytes_retransmit=9 bytes_invalid=0 send_seq=884 receive_seq=884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6193 bytes_read=18447 bytes_retransmit=9 bytes_invalid=0 send_seq=879 receive_seq=879 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49269 bytes_read=487967 bytes_retransmit=0 bytes_invalid=0 send_seq=4516 receive_seq=4516 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998597 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=47.7 th1: temp=46.9 th2: temp=48.2 th3: temp=46.5 sysload=0.10 cputime=97.327 memavail=7407400 print_time=812.036 buffer_time=2.162 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 788.4: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8577142 bytes_read=1064943 bytes_retransmit=9 bytes_invalid=0 send_seq=151164 receive_seq=151164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=42614 freq=400015800 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5452 bytes_read=18828 bytes_retransmit=0 bytes_invalid=0 send_seq=880 receive_seq=880 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998930 adj=49997066 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44961 bytes_read=1462404 bytes_retransmit=9 bytes_invalid=0 send_seq=6053 receive_seq=6053 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997908 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14544 bytes_read=102427 bytes_retransmit=9 bytes_invalid=0 send_seq=1623 receive_seq=1623 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997484 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5611 bytes_read=196555 bytes_retransmit=9 bytes_invalid=0 send_seq=886 receive_seq=886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6205 bytes_read=18479 bytes_retransmit=9 bytes_invalid=0 send_seq=881 receive_seq=881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49281 bytes_read=488339 bytes_retransmit=0 bytes_invalid=0 send_seq=4518 receive_seq=4518 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998610 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=47.8 th1: temp=46.9 th2: temp=48.3 th3: temp=46.5 sysload=0.10 cputime=97.475 memavail=7407400 print_time=813.112 buffer_time=2.238 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 789.4: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8601936 bytes_read=1067278 bytes_retransmit=9 bytes_invalid=0 send_seq=151569 receive_seq=151569 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=44470 freq=400015794 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5458 bytes_read=18844 bytes_retransmit=0 bytes_invalid=0 send_seq=881 receive_seq=881 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998931 adj=49997123 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45037 bytes_read=1465519 bytes_retransmit=9 bytes_invalid=0 send_seq=6064 receive_seq=6064 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997812 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14550 bytes_read=102527 bytes_retransmit=9 bytes_invalid=0 send_seq=1624 receive_seq=1624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5617 bytes_read=196804 bytes_retransmit=9 bytes_invalid=0 send_seq=887 receive_seq=887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6211 bytes_read=18495 bytes_retransmit=9 bytes_invalid=0 send_seq=882 receive_seq=882 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49287 bytes_read=488695 bytes_retransmit=0 bytes_invalid=0 send_seq=4519 receive_seq=4519 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998642 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=48.2 th1: temp=47.3 th2: temp=48.5 th3: temp=46.5 sysload=0.10 cputime=97.619 memavail=7407400 print_time=814.189 buffer_time=2.313 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 790.4: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8626715 bytes_read=1069624 bytes_retransmit=9 bytes_invalid=0 send_seq=151973 receive_seq=151973 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=46326 freq=400015791 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5464 bytes_read=18860 bytes_retransmit=0 bytes_invalid=0 send_seq=882 receive_seq=882 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998933 adj=49997111 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45113 bytes_read=1468605 bytes_retransmit=9 bytes_invalid=0 send_seq=6075 receive_seq=6075 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997789 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14556 bytes_read=102655 bytes_retransmit=9 bytes_invalid=0 send_seq=1625 receive_seq=1625 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997517 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5623 bytes_read=197083 bytes_retransmit=9 bytes_invalid=0 send_seq=888 receive_seq=888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6217 bytes_read=18511 bytes_retransmit=9 bytes_invalid=0 send_seq=883 receive_seq=883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49293 bytes_read=489051 bytes_retransmit=0 bytes_invalid=0 send_seq=4520 receive_seq=4520 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998644 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=47.8 th1: temp=46.9 th2: temp=48.4 th3: temp=46.6 sysload=0.10 cputime=97.764 memavail=7407400 print_time=815.265 buffer_time=2.390 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 791.4: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8651504 bytes_read=1071993 bytes_retransmit=9 bytes_invalid=0 send_seq=152379 receive_seq=152379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=48182 freq=400015868 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5470 bytes_read=18876 bytes_retransmit=0 bytes_invalid=0 send_seq=883 receive_seq=883 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998935 adj=49997109 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45182 bytes_read=1471656 bytes_retransmit=9 bytes_invalid=0 send_seq=6085 receive_seq=6085 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997765 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14562 bytes_read=102755 bytes_retransmit=9 bytes_invalid=0 send_seq=1626 receive_seq=1626 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997529 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5629 bytes_read=197317 bytes_retransmit=9 bytes_invalid=0 send_seq=889 receive_seq=889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6223 bytes_read=18527 bytes_retransmit=9 bytes_invalid=0 send_seq=884 receive_seq=884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49299 bytes_read=489407 bytes_retransmit=0 bytes_invalid=0 send_seq=4521 receive_seq=4521 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998646 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=47.7 th1: temp=46.8 th2: temp=48.1 th3: temp=46.7 sysload=0.09 cputime=97.909 memavail=7407400 print_time=816.342 buffer_time=2.466 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 792.4: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8676333 bytes_read=1074333 bytes_retransmit=9 bytes_invalid=0 send_seq=152785 receive_seq=152785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=37809 freq=400015949 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5476 bytes_read=18892 bytes_retransmit=0 bytes_invalid=0 send_seq=884 receive_seq=884 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998938 adj=49996997 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45258 bytes_read=1474714 bytes_retransmit=9 bytes_invalid=0 send_seq=6096 receive_seq=6096 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997587 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14568 bytes_read=102855 bytes_retransmit=9 bytes_invalid=0 send_seq=1627 receive_seq=1627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997392 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5635 bytes_read=197566 bytes_retransmit=9 bytes_invalid=0 send_seq=890 receive_seq=890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997542 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6229 bytes_read=18554 bytes_retransmit=9 bytes_invalid=0 send_seq=885 receive_seq=885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999413 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49305 bytes_read=489763 bytes_retransmit=0 bytes_invalid=0 send_seq=4522 receive_seq=4522 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998580 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=47.8 th1: temp=47.0 th2: temp=48.5 th3: temp=46.3 sysload=0.09 cputime=98.034 memavail=7407176 print_time=816.880 buffer_time=2.003 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 793.4: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8701127 bytes_read=1076676 bytes_retransmit=9 bytes_invalid=0 send_seq=153192 receive_seq=153192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=39665 freq=400015924 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5482 bytes_read=18921 bytes_retransmit=0 bytes_invalid=0 send_seq=885 receive_seq=885 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998940 adj=49996904 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45334 bytes_read=1477799 bytes_retransmit=9 bytes_invalid=0 send_seq=6107 receive_seq=6107 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997402 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14574 bytes_read=102997 bytes_retransmit=9 bytes_invalid=0 send_seq=1628 receive_seq=1628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997230 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=5641 bytes_read=197860 bytes_retransmit=9 bytes_invalid=0 send_seq=891 receive_seq=891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997421 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6235 bytes_read=18570 bytes_retransmit=9 bytes_invalid=0 send_seq=886 receive_seq=886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999383 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49311 bytes_read=490119 bytes_retransmit=0 bytes_invalid=0 send_seq=4523 receive_seq=4523 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998496 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=48.0 th1: temp=47.0 th2: temp=48.3 th3: temp=46.5 sysload=0.09 cputime=98.184 memavail=7407176 print_time=817.957 buffer_time=2.079 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 794.4: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8726901 bytes_read=1079117 bytes_retransmit=9 bytes_invalid=0 send_seq=153613 receive_seq=153613 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40593 freq=400015897 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5488 bytes_read=18937 bytes_retransmit=0 bytes_invalid=0 send_seq=886 receive_seq=886 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998942 adj=49996980 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45410 bytes_read=1480855 bytes_retransmit=9 bytes_invalid=0 send_seq=6118 receive_seq=6118 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997451 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14580 bytes_read=103097 bytes_retransmit=9 bytes_invalid=0 send_seq=1629 receive_seq=1629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997297 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=5647 bytes_read=198094 bytes_retransmit=9 bytes_invalid=0 send_seq=892 receive_seq=892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997463 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6241 bytes_read=18586 bytes_retransmit=9 bytes_invalid=0 send_seq=887 receive_seq=887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999398 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49317 bytes_read=490475 bytes_retransmit=0 bytes_invalid=0 send_seq=4524 receive_seq=4524 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998537 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=48.1 th1: temp=47.1 th2: temp=48.6 th3: temp=46.8 sysload=0.09 cputime=98.329 memavail=7407176 print_time=819.033 buffer_time=2.154 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 795.4: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8751728 bytes_read=1081493 bytes_retransmit=9 bytes_invalid=0 send_seq=154023 receive_seq=154023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=42449 freq=400015963 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5494 bytes_read=18953 bytes_retransmit=0 bytes_invalid=0 send_seq=887 receive_seq=887 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998949 adj=49997041 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45486 bytes_read=1483911 bytes_retransmit=9 bytes_invalid=0 send_seq=6129 receive_seq=6129 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997536 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14586 bytes_read=103197 bytes_retransmit=9 bytes_invalid=0 send_seq=1630 receive_seq=1630 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997394 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=5653 bytes_read=198343 bytes_retransmit=9 bytes_invalid=0 send_seq=893 receive_seq=893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997523 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6247 bytes_read=18602 bytes_retransmit=9 bytes_invalid=0 send_seq=888 receive_seq=888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999416 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49323 bytes_read=490831 bytes_retransmit=0 bytes_invalid=0 send_seq=4525 receive_seq=4525 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998591 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=47.8 th1: temp=47.0 th2: temp=48.5 th3: temp=46.6 sysload=0.09 cputime=98.477 memavail=7407996 print_time=820.110 buffer_time=2.230 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 796.4: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8776489 bytes_read=1083823 bytes_retransmit=9 bytes_invalid=0 send_seq=154427 receive_seq=154427 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=44275 freq=400015945 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5500 bytes_read=18969 bytes_retransmit=0 bytes_invalid=0 send_seq=888 receive_seq=888 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998950 adj=49996999 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45562 bytes_read=1487014 bytes_retransmit=9 bytes_invalid=0 send_seq=6140 receive_seq=6140 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997424 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14592 bytes_read=103325 bytes_retransmit=9 bytes_invalid=0 send_seq=1631 receive_seq=1631 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997295 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=5659 bytes_read=198622 bytes_retransmit=9 bytes_invalid=0 send_seq=894 receive_seq=894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997441 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6253 bytes_read=18618 bytes_retransmit=9 bytes_invalid=0 send_seq=889 receive_seq=889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999400 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49329 bytes_read=491187 bytes_retransmit=0 bytes_invalid=0 send_seq=4526 receive_seq=4526 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998533 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=47.9 th1: temp=46.9 th2: temp=48.3 th3: temp=46.5 sysload=0.09 cputime=98.627 memavail=7407520 print_time=821.186 buffer_time=2.306 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 797.4: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8801283 bytes_read=1086197 bytes_retransmit=9 bytes_invalid=0 send_seq=154834 receive_seq=154834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=46131 freq=400015944 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5506 bytes_read=18985 bytes_retransmit=0 bytes_invalid=0 send_seq=889 receive_seq=889 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998953 adj=49997026 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45638 bytes_read=1490128 bytes_retransmit=9 bytes_invalid=0 send_seq=6151 receive_seq=6151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997477 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14598 bytes_read=103425 bytes_retransmit=9 bytes_invalid=0 send_seq=1632 receive_seq=1632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997353 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=5665 bytes_read=198856 bytes_retransmit=9 bytes_invalid=0 send_seq=895 receive_seq=895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997512 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6259 bytes_read=18645 bytes_retransmit=9 bytes_invalid=0 send_seq=890 receive_seq=890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999413 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49335 bytes_read=491543 bytes_retransmit=0 bytes_invalid=0 send_seq=4527 receive_seq=4527 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998569 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=48.0 th1: temp=46.9 th2: temp=48.4 th3: temp=46.5 sysload=0.09 cputime=98.780 memavail=7407520 print_time=822.262 buffer_time=2.382 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 798.4: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8826077 bytes_read=1088542 bytes_retransmit=9 bytes_invalid=0 send_seq=155241 receive_seq=155241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=47987 freq=400015927 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000013 bytes_write=5512 bytes_read=19014 bytes_retransmit=0 bytes_invalid=0 send_seq=890 receive_seq=890 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998954 adj=49997048 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45714 bytes_read=1493184 bytes_retransmit=9 bytes_invalid=0 send_seq=6162 receive_seq=6162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997501 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14604 bytes_read=103539 bytes_retransmit=9 bytes_invalid=0 send_seq=1633 receive_seq=1633 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997384 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5671 bytes_read=199120 bytes_retransmit=9 bytes_invalid=0 send_seq=896 receive_seq=896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997537 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6265 bytes_read=18661 bytes_retransmit=9 bytes_invalid=0 send_seq=891 receive_seq=891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999423 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49341 bytes_read=491899 bytes_retransmit=0 bytes_invalid=0 send_seq=4528 receive_seq=4528 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998581 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=47.8 th1: temp=47.2 th2: temp=48.4 th3: temp=46.6 sysload=0.09 cputime=98.933 memavail=7407520 print_time=823.339 buffer_time=2.458 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 799.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8851172 bytes_read=1090917 bytes_retransmit=9 bytes_invalid=0 send_seq=155654 receive_seq=155654 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=49596 freq=400015903 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000013 bytes_write=5518 bytes_read=19030 bytes_retransmit=0 bytes_invalid=0 send_seq=891 receive_seq=891 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998956 adj=49997070 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45790 bytes_read=1496270 bytes_retransmit=9 bytes_invalid=0 send_seq=6173 receive_seq=6173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997537 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14610 bytes_read=103667 bytes_retransmit=9 bytes_invalid=0 send_seq=1634 receive_seq=1634 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997442 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5677 bytes_read=199399 bytes_retransmit=9 bytes_invalid=0 send_seq=897 receive_seq=897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997565 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6271 bytes_read=18677 bytes_retransmit=9 bytes_invalid=0 send_seq=892 receive_seq=892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49347 bytes_read=492273 bytes_retransmit=0 bytes_invalid=0 send_seq=4529 receive_seq=4529 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998604 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=47.7 th1: temp=46.9 th2: temp=48.4 th3: temp=46.6 sysload=0.09 cputime=99.084 memavail=7407520 print_time=824.415 buffer_time=2.524 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 800.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8875976 bytes_read=1093317 bytes_retransmit=9 bytes_invalid=0 send_seq=156063 receive_seq=156063 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=39236 freq=400016043 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000013 bytes_write=5524 bytes_read=19046 bytes_retransmit=0 bytes_invalid=0 send_seq=892 receive_seq=892 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998958 adj=49997100 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45866 bytes_read=1499328 bytes_retransmit=9 bytes_invalid=0 send_seq=6184 receive_seq=6184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997575 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14616 bytes_read=103767 bytes_retransmit=9 bytes_invalid=0 send_seq=1635 receive_seq=1635 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5683 bytes_read=199633 bytes_retransmit=9 bytes_invalid=0 send_seq=898 receive_seq=898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997594 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6277 bytes_read=18693 bytes_retransmit=9 bytes_invalid=0 send_seq=893 receive_seq=893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49353 bytes_read=492629 bytes_retransmit=0 bytes_invalid=0 send_seq=4530 receive_seq=4530 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999905 adj=31998622 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.2 th2: temp=48.5 th3: temp=46.6 sysload=0.09 cputime=99.222 memavail=7407524 print_time=824.954 buffer_time=2.062 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 801.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8901457 bytes_read=1095712 bytes_retransmit=9 bytes_invalid=0 send_seq=156480 receive_seq=156480 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400016023 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000013 bytes_write=5530 bytes_read=19062 bytes_retransmit=0 bytes_invalid=0 send_seq=893 receive_seq=893 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998960 adj=49996921 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45942 bytes_read=1502461 bytes_retransmit=9 bytes_invalid=0 send_seq=6195 receive_seq=6195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997325 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14622 bytes_read=103867 bytes_retransmit=9 bytes_invalid=0 send_seq=1636 receive_seq=1636 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997227 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5689 bytes_read=199897 bytes_retransmit=9 bytes_invalid=0 send_seq=899 receive_seq=899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997392 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6283 bytes_read=18709 bytes_retransmit=9 bytes_invalid=0 send_seq=894 receive_seq=894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999392 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49359 bytes_read=492967 bytes_retransmit=0 bytes_invalid=0 send_seq=4531 receive_seq=4531 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998493 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=47.9 th1: temp=47.0 th2: temp=48.6 th3: temp=46.6 sysload=0.08 cputime=99.376 memavail=7407112 print_time=826.030 buffer_time=2.138 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 802.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8926546 bytes_read=1098077 bytes_retransmit=9 bytes_invalid=0 send_seq=156891 receive_seq=156891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=42020 freq=400016009 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000013 bytes_write=5536 bytes_read=19078 bytes_retransmit=0 bytes_invalid=0 send_seq=894 receive_seq=894 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998961 adj=49996982 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46018 bytes_read=1505547 bytes_retransmit=9 bytes_invalid=0 send_seq=6206 receive_seq=6206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997379 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14628 bytes_read=103995 bytes_retransmit=9 bytes_invalid=0 send_seq=1637 receive_seq=1637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997425 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5695 bytes_read=200161 bytes_retransmit=9 bytes_invalid=0 send_seq=900 receive_seq=900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997440 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6289 bytes_read=18736 bytes_retransmit=9 bytes_invalid=0 send_seq=895 receive_seq=895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999405 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49365 bytes_read=493341 bytes_retransmit=0 bytes_invalid=0 send_seq=4532 receive_seq=4532 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998545 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=47.8 th1: temp=46.9 th2: temp=48.5 th3: temp=46.7 sysload=0.08 cputime=99.526 memavail=7407112 print_time=827.107 buffer_time=2.214 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 803.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8951420 bytes_read=1100456 bytes_retransmit=9 bytes_invalid=0 send_seq=157299 receive_seq=157299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=43841 freq=400016187 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5542 bytes_read=19107 bytes_retransmit=0 bytes_invalid=0 send_seq=895 receive_seq=895 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998962 adj=49997012 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46094 bytes_read=1508603 bytes_retransmit=9 bytes_invalid=0 send_seq=6217 receive_seq=6217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997443 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14634 bytes_read=104109 bytes_retransmit=9 bytes_invalid=0 send_seq=1638 receive_seq=1638 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997456 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5701 bytes_read=200410 bytes_retransmit=9 bytes_invalid=0 send_seq=901 receive_seq=901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997503 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6295 bytes_read=18752 bytes_retransmit=9 bytes_invalid=0 send_seq=896 receive_seq=896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999416 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49371 bytes_read=493697 bytes_retransmit=0 bytes_invalid=0 send_seq=4533 receive_seq=4533 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998571 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.1 th2: temp=48.5 th3: temp=46.7 sysload=0.08 cputime=99.687 memavail=7405980 print_time=828.183 buffer_time=2.289 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 804.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=8976204 bytes_read=1102786 bytes_retransmit=9 bytes_invalid=0 send_seq=157704 receive_seq=157704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=45697 freq=400016146 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5548 bytes_read=19123 bytes_retransmit=0 bytes_invalid=0 send_seq=896 receive_seq=896 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998964 adj=49996757 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46163 bytes_read=1511651 bytes_retransmit=9 bytes_invalid=0 send_seq=6227 receive_seq=6227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997150 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14640 bytes_read=104209 bytes_retransmit=9 bytes_invalid=0 send_seq=1639 receive_seq=1639 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997111 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5707 bytes_read=200689 bytes_retransmit=9 bytes_invalid=0 send_seq=902 receive_seq=902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997268 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6301 bytes_read=18768 bytes_retransmit=9 bytes_invalid=0 send_seq=897 receive_seq=897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999362 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49377 bytes_read=494053 bytes_retransmit=0 bytes_invalid=0 send_seq=4534 receive_seq=4534 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998413 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=47.9 th1: temp=46.8 th2: temp=48.4 th3: temp=46.7 sysload=0.08 cputime=99.834 memavail=7405980 print_time=829.260 buffer_time=2.364 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 805.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9000993 bytes_read=1105142 bytes_retransmit=9 bytes_invalid=0 send_seq=158110 receive_seq=158110 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=47553 freq=400016105 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5554 bytes_read=19139 bytes_retransmit=0 bytes_invalid=0 send_seq=897 receive_seq=897 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998967 adj=49996876 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46239 bytes_read=1514723 bytes_retransmit=9 bytes_invalid=0 send_seq=6238 receive_seq=6238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997301 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14646 bytes_read=104337 bytes_retransmit=9 bytes_invalid=0 send_seq=1640 receive_seq=1640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997262 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5713 bytes_read=200938 bytes_retransmit=9 bytes_invalid=0 send_seq=903 receive_seq=903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997395 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6307 bytes_read=18784 bytes_retransmit=9 bytes_invalid=0 send_seq=898 receive_seq=898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999401 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49383 bytes_read=494409 bytes_retransmit=0 bytes_invalid=0 send_seq=4535 receive_seq=4535 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999905 adj=31998491 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=47.6 th1: temp=47.1 th2: temp=48.6 th3: temp=46.7 sysload=0.08 cputime=99.982 memavail=7405740 print_time=830.336 buffer_time=2.440 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 806.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9025803 bytes_read=1107506 bytes_retransmit=9 bytes_invalid=0 send_seq=158516 receive_seq=158515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=49364 freq=400016078 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5560 bytes_read=19155 bytes_retransmit=0 bytes_invalid=0 send_seq=898 receive_seq=898 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998969 adj=49996968 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46315 bytes_read=1517796 bytes_retransmit=9 bytes_invalid=0 send_seq=6249 receive_seq=6249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997432 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14652 bytes_read=104437 bytes_retransmit=9 bytes_invalid=0 send_seq=1641 receive_seq=1641 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997364 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5719 bytes_read=201172 bytes_retransmit=9 bytes_invalid=0 send_seq=904 receive_seq=904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997493 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6313 bytes_read=18800 bytes_retransmit=9 bytes_invalid=0 send_seq=899 receive_seq=899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999422 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49389 bytes_read=494765 bytes_retransmit=0 bytes_invalid=0 send_seq=4536 receive_seq=4536 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999905 adj=31998546 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=48.0 th1: temp=46.9 th2: temp=48.1 th3: temp=46.9 sysload=0.07 cputime=100.126 memavail=7405740 print_time=831.412 buffer_time=2.516 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 807.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9050591 bytes_read=1109866 bytes_retransmit=9 bytes_invalid=0 send_seq=158925 receive_seq=158925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=39036 freq=400016124 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5566 bytes_read=19171 bytes_retransmit=0 bytes_invalid=0 send_seq=899 receive_seq=899 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998970 adj=49997023 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46391 bytes_read=1520925 bytes_retransmit=9 bytes_invalid=0 send_seq=6260 receive_seq=6260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997500 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14658 bytes_read=104551 bytes_retransmit=9 bytes_invalid=0 send_seq=1642 receive_seq=1642 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997416 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5725 bytes_read=201451 bytes_retransmit=9 bytes_invalid=0 send_seq=905 receive_seq=905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997552 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6319 bytes_read=18827 bytes_retransmit=9 bytes_invalid=0 send_seq=900 receive_seq=900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49395 bytes_read=495121 bytes_retransmit=0 bytes_invalid=0 send_seq=4537 receive_seq=4537 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998586 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=47.9 th1: temp=47.1 th2: temp=48.5 th3: temp=46.7 sysload=0.07 cputime=100.259 memavail=7405740 print_time=831.951 buffer_time=2.053 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 808.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9075811 bytes_read=1112216 bytes_retransmit=9 bytes_invalid=0 send_seq=159333 receive_seq=159333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400016110 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5572 bytes_read=19200 bytes_retransmit=0 bytes_invalid=0 send_seq=900 receive_seq=900 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998973 adj=49996978 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46467 bytes_read=1523995 bytes_retransmit=9 bytes_invalid=0 send_seq=6271 receive_seq=6271 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997400 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14664 bytes_read=104679 bytes_retransmit=9 bytes_invalid=0 send_seq=1643 receive_seq=1643 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997313 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5731 bytes_read=201715 bytes_retransmit=9 bytes_invalid=0 send_seq=906 receive_seq=906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997493 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6325 bytes_read=18843 bytes_retransmit=9 bytes_invalid=0 send_seq=901 receive_seq=901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999417 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49401 bytes_read=495477 bytes_retransmit=0 bytes_invalid=0 send_seq=4538 receive_seq=4538 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998585 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=47.9 th1: temp=47.1 th2: temp=48.8 th3: temp=46.7 sysload=0.07 cputime=100.408 memavail=7405740 print_time=833.027 buffer_time=2.129 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 809.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9101147 bytes_read=1114625 bytes_retransmit=9 bytes_invalid=0 send_seq=159747 receive_seq=159747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=41820 freq=400016086 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5578 bytes_read=19216 bytes_retransmit=0 bytes_invalid=0 send_seq=901 receive_seq=901 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998975 adj=49997032 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46543 bytes_read=1527052 bytes_retransmit=9 bytes_invalid=0 send_seq=6282 receive_seq=6282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000181 adj=63997453 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14670 bytes_read=104779 bytes_retransmit=9 bytes_invalid=0 send_seq=1644 receive_seq=1644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997355 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5737 bytes_read=201949 bytes_retransmit=9 bytes_invalid=0 send_seq=907 receive_seq=907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997558 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6331 bytes_read=18859 bytes_retransmit=9 bytes_invalid=0 send_seq=902 receive_seq=902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999422 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49407 bytes_read=495833 bytes_retransmit=0 bytes_invalid=0 send_seq=4539 receive_seq=4539 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998604 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=48.0 th1: temp=46.9 th2: temp=48.6 th3: temp=46.8 sysload=0.07 cputime=100.555 memavail=7405516 print_time=834.104 buffer_time=2.205 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 810.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9125903 bytes_read=1116991 bytes_retransmit=9 bytes_invalid=0 send_seq=160155 receive_seq=160155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=43676 freq=400016086 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5584 bytes_read=19232 bytes_retransmit=0 bytes_invalid=0 send_seq=902 receive_seq=902 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998978 adj=49997078 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46619 bytes_read=1530122 bytes_retransmit=9 bytes_invalid=0 send_seq=6293 receive_seq=6293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997522 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14676 bytes_read=104893 bytes_retransmit=9 bytes_invalid=0 send_seq=1645 receive_seq=1645 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997407 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5743 bytes_read=202228 bytes_retransmit=9 bytes_invalid=0 send_seq=908 receive_seq=908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997588 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6337 bytes_read=18875 bytes_retransmit=9 bytes_invalid=0 send_seq=903 receive_seq=903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49413 bytes_read=496189 bytes_retransmit=0 bytes_invalid=0 send_seq=4540 receive_seq=4540 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998623 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=47.9 th1: temp=47.0 th2: temp=48.6 th3: temp=46.8 sysload=0.07 cputime=100.707 memavail=7405516 print_time=835.180 buffer_time=2.281 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 811.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9150702 bytes_read=1119341 bytes_retransmit=9 bytes_invalid=0 send_seq=160563 receive_seq=160563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=45532 freq=400016060 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5590 bytes_read=19248 bytes_retransmit=0 bytes_invalid=0 send_seq=903 receive_seq=903 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998979 adj=49997080 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46695 bytes_read=1533211 bytes_retransmit=9 bytes_invalid=0 send_seq=6304 receive_seq=6304 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000179 adj=63997531 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14682 bytes_read=105007 bytes_retransmit=9 bytes_invalid=0 send_seq=1646 receive_seq=1646 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997402 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5749 bytes_read=202477 bytes_retransmit=9 bytes_invalid=0 send_seq=909 receive_seq=909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997579 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6343 bytes_read=18891 bytes_retransmit=9 bytes_invalid=0 send_seq=904 receive_seq=904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49419 bytes_read=496545 bytes_retransmit=0 bytes_invalid=0 send_seq=4541 receive_seq=4541 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998620 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=47.9 th1: temp=47.1 th2: temp=48.7 th3: temp=46.8 sysload=0.07 cputime=100.855 memavail=7405516 print_time=836.257 buffer_time=2.357 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 812.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9175501 bytes_read=1121720 bytes_retransmit=9 bytes_invalid=0 send_seq=160971 receive_seq=160971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=47388 freq=400016028 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5596 bytes_read=19264 bytes_retransmit=0 bytes_invalid=0 send_seq=904 receive_seq=904 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998981 adj=49997111 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46771 bytes_read=1536270 bytes_retransmit=9 bytes_invalid=0 send_seq=6315 receive_seq=6315 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997583 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14688 bytes_read=105107 bytes_retransmit=9 bytes_invalid=0 send_seq=1647 receive_seq=1647 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997442 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5755 bytes_read=202711 bytes_retransmit=9 bytes_invalid=0 send_seq=910 receive_seq=910 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999535 adj=47997606 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6349 bytes_read=18918 bytes_retransmit=9 bytes_invalid=0 send_seq=905 receive_seq=905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49425 bytes_read=496901 bytes_retransmit=0 bytes_invalid=0 send_seq=4542 receive_seq=4542 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998637 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=47.8 th1: temp=47.2 th2: temp=48.6 th3: temp=46.8 sysload=0.07 cputime=101.006 memavail=7405516 print_time=837.333 buffer_time=2.434 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 813.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9200313 bytes_read=1124060 bytes_retransmit=9 bytes_invalid=0 send_seq=161377 receive_seq=161377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=49231 freq=400016002 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5602 bytes_read=19293 bytes_retransmit=0 bytes_invalid=0 send_seq=905 receive_seq=905 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998983 adj=49997146 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46847 bytes_read=1539340 bytes_retransmit=9 bytes_invalid=0 send_seq=6326 receive_seq=6326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000177 adj=63997635 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14694 bytes_read=105235 bytes_retransmit=9 bytes_invalid=0 send_seq=1648 receive_seq=1648 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997487 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5761 bytes_read=203005 bytes_retransmit=9 bytes_invalid=0 send_seq=911 receive_seq=911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6355 bytes_read=18934 bytes_retransmit=9 bytes_invalid=0 send_seq=906 receive_seq=906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49431 bytes_read=497257 bytes_retransmit=0 bytes_invalid=0 send_seq=4543 receive_seq=4543 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998670 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=47.9 th1: temp=47.2 th2: temp=48.6 th3: temp=46.8 sysload=0.07 cputime=101.149 memavail=7405516 print_time=838.409 buffer_time=2.510 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 814.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9225095 bytes_read=1126410 bytes_retransmit=9 bytes_invalid=0 send_seq=161785 receive_seq=161785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=38871 freq=400015965 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5608 bytes_read=19309 bytes_retransmit=0 bytes_invalid=0 send_seq=906 receive_seq=906 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998985 adj=49997168 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46923 bytes_read=1542411 bytes_retransmit=9 bytes_invalid=0 send_seq=6337 receive_seq=6337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000177 adj=63997668 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14700 bytes_read=105349 bytes_retransmit=9 bytes_invalid=0 send_seq=1649 receive_seq=1649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997518 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5767 bytes_read=203254 bytes_retransmit=9 bytes_invalid=0 send_seq=912 receive_seq=912 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6361 bytes_read=18950 bytes_retransmit=9 bytes_invalid=0 send_seq=907 receive_seq=907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49437 bytes_read=497613 bytes_retransmit=0 bytes_invalid=0 send_seq=4544 receive_seq=4544 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998684 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=47.9 th1: temp=47.0 th2: temp=48.8 th3: temp=46.8 sysload=0.07 cputime=101.283 memavail=7405516 print_time=838.948 buffer_time=2.048 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 815.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9250189 bytes_read=1128805 bytes_retransmit=9 bytes_invalid=0 send_seq=162194 receive_seq=162194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=40461 freq=400015929 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5614 bytes_read=19325 bytes_retransmit=0 bytes_invalid=0 send_seq=907 receive_seq=907 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998987 adj=49997238 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46992 bytes_read=1545502 bytes_retransmit=9 bytes_invalid=0 send_seq=6347 receive_seq=6347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000176 adj=63997728 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14706 bytes_read=105449 bytes_retransmit=9 bytes_invalid=0 send_seq=1650 receive_seq=1650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997573 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5773 bytes_read=203488 bytes_retransmit=9 bytes_invalid=0 send_seq=913 receive_seq=913 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997695 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6367 bytes_read=18966 bytes_retransmit=9 bytes_invalid=0 send_seq=908 receive_seq=908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49443 bytes_read=497969 bytes_retransmit=0 bytes_invalid=0 send_seq=4545 receive_seq=4545 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998719 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=48.0 th1: temp=47.0 th2: temp=48.6 th3: temp=47.0 sysload=0.07 cputime=101.431 memavail=7405300 print_time=840.024 buffer_time=2.123 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 816.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9275681 bytes_read=1131210 bytes_retransmit=9 bytes_invalid=0 send_seq=162613 receive_seq=162613 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=41686 freq=400015907 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5620 bytes_read=19341 bytes_retransmit=0 bytes_invalid=0 send_seq=908 receive_seq=908 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998989 adj=49997295 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47068 bytes_read=1548591 bytes_retransmit=9 bytes_invalid=0 send_seq=6358 receive_seq=6358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997778 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14712 bytes_read=105563 bytes_retransmit=9 bytes_invalid=0 send_seq=1651 receive_seq=1651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000018 adj=63997628 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5779 bytes_read=203767 bytes_retransmit=9 bytes_invalid=0 send_seq=914 receive_seq=914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997742 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6373 bytes_read=18982 bytes_retransmit=9 bytes_invalid=0 send_seq=909 receive_seq=909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999470 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49449 bytes_read=498325 bytes_retransmit=0 bytes_invalid=0 send_seq=4546 receive_seq=4546 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998741 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.011 th0: temp=47.7 th1: temp=46.9 th2: temp=48.7 th3: temp=47.0 sysload=0.06 cputime=101.577 memavail=7405300 print_time=841.101 buffer_time=2.199 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 817.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9300447 bytes_read=1133510 bytes_retransmit=9 bytes_invalid=0 send_seq=163011 receive_seq=163011 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=43542 freq=400015882 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5626 bytes_read=19357 bytes_retransmit=0 bytes_invalid=0 send_seq=909 receive_seq=909 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998991 adj=49997286 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47144 bytes_read=1551663 bytes_retransmit=9 bytes_invalid=0 send_seq=6369 receive_seq=6369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997855 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14718 bytes_read=105677 bytes_retransmit=9 bytes_invalid=0 send_seq=1652 receive_seq=1652 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000017 adj=63997624 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5785 bytes_read=204016 bytes_retransmit=9 bytes_invalid=0 send_seq=915 receive_seq=915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997759 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6379 bytes_read=19009 bytes_retransmit=9 bytes_invalid=0 send_seq=910 receive_seq=910 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999471 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49455 bytes_read=498681 bytes_retransmit=0 bytes_invalid=0 send_seq=4547 receive_seq=4547 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998730 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.011 th0: temp=48.0 th1: temp=47.1 th2: temp=48.7 th3: temp=46.9 sysload=0.06 cputime=101.725 memavail=7405300 print_time=842.177 buffer_time=2.275 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 818.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9325224 bytes_read=1135884 bytes_retransmit=9 bytes_invalid=0 send_seq=163418 receive_seq=163418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=45398 freq=400015852 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5632 bytes_read=19386 bytes_retransmit=0 bytes_invalid=0 send_seq=910 receive_seq=910 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998993 adj=49997283 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47220 bytes_read=1554720 bytes_retransmit=9 bytes_invalid=0 send_seq=6380 receive_seq=6380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997923 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14724 bytes_read=105777 bytes_retransmit=9 bytes_invalid=0 send_seq=1653 receive_seq=1653 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000017 adj=63997626 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5791 bytes_read=204265 bytes_retransmit=9 bytes_invalid=0 send_seq=916 receive_seq=916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999535 adj=47997781 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6385 bytes_read=19025 bytes_retransmit=9 bytes_invalid=0 send_seq=911 receive_seq=911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999471 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49461 bytes_read=499037 bytes_retransmit=0 bytes_invalid=0 send_seq=4548 receive_seq=4548 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998731 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=48.4 th1: temp=47.0 th2: temp=48.9 th3: temp=47.0 sysload=0.06 cputime=101.880 memavail=7405560 print_time=843.254 buffer_time=2.351 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 819.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9350008 bytes_read=1138219 bytes_retransmit=9 bytes_invalid=0 send_seq=163823 receive_seq=163823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=47254 freq=400015839 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5638 bytes_read=19402 bytes_retransmit=0 bytes_invalid=0 send_seq=911 receive_seq=911 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998996 adj=49997287 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47296 bytes_read=1557791 bytes_retransmit=9 bytes_invalid=0 send_seq=6391 receive_seq=6391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997923 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14730 bytes_read=105905 bytes_retransmit=9 bytes_invalid=0 send_seq=1654 receive_seq=1654 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997641 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5797 bytes_read=204544 bytes_retransmit=9 bytes_invalid=0 send_seq=917 receive_seq=917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997778 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6391 bytes_read=19041 bytes_retransmit=9 bytes_invalid=0 send_seq=912 receive_seq=912 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999474 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49467 bytes_read=499393 bytes_retransmit=0 bytes_invalid=0 send_seq=4549 receive_seq=4549 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998730 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.011 th0: temp=47.9 th1: temp=47.1 th2: temp=48.7 th3: temp=46.8 sysload=0.06 cputime=102.032 memavail=7405560 print_time=844.330 buffer_time=2.427 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 820.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9374814 bytes_read=1140570 bytes_retransmit=9 bytes_invalid=0 send_seq=164228 receive_seq=164228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=49097 freq=400015976 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5644 bytes_read=19418 bytes_retransmit=0 bytes_invalid=0 send_seq=912 receive_seq=912 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998998 adj=49997279 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47372 bytes_read=1560863 bytes_retransmit=9 bytes_invalid=0 send_seq=6402 receive_seq=6402 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997875 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14736 bytes_read=106019 bytes_retransmit=9 bytes_invalid=0 send_seq=1655 receive_seq=1655 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997761 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5803 bytes_read=204793 bytes_retransmit=9 bytes_invalid=0 send_seq=918 receive_seq=918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999535 adj=47997758 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6397 bytes_read=19057 bytes_retransmit=9 bytes_invalid=0 send_seq=913 receive_seq=913 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999472 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49473 bytes_read=499749 bytes_retransmit=0 bytes_invalid=0 send_seq=4550 receive_seq=4550 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998731 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.011 th0: temp=48.2 th1: temp=47.1 th2: temp=49.0 th3: temp=46.8 sysload=0.06 cputime=102.189 memavail=7399796 print_time=845.407 buffer_time=2.504 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 821.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9399613 bytes_read=1142949 bytes_retransmit=9 bytes_invalid=0 send_seq=164636 receive_seq=164636 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=38737 freq=400016196 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5650 bytes_read=19434 bytes_retransmit=0 bytes_invalid=0 send_seq=913 receive_seq=913 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999000 adj=49997063 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47448 bytes_read=1563937 bytes_retransmit=9 bytes_invalid=0 send_seq=6413 receive_seq=6413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997678 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14742 bytes_read=106119 bytes_retransmit=9 bytes_invalid=0 send_seq=1656 receive_seq=1656 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997470 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5809 bytes_read=205027 bytes_retransmit=9 bytes_invalid=0 send_seq=919 receive_seq=919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997561 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6403 bytes_read=19073 bytes_retransmit=9 bytes_invalid=0 send_seq=914 receive_seq=914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999422 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49479 bytes_read=500105 bytes_retransmit=0 bytes_invalid=0 send_seq=4551 receive_seq=4551 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998595 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=48.0 th1: temp=47.3 th2: temp=48.7 th3: temp=46.9 sysload=0.14 cputime=102.327 memavail=7406940 print_time=845.945 buffer_time=2.042 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 822.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9424549 bytes_read=1145304 bytes_retransmit=9 bytes_invalid=0 send_seq=165045 receive_seq=165045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400016149 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5656 bytes_read=19450 bytes_retransmit=0 bytes_invalid=0 send_seq=914 receive_seq=914 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999000 adj=49996764 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47524 bytes_read=1567009 bytes_retransmit=9 bytes_invalid=0 send_seq=6424 receive_seq=6424 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997305 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14748 bytes_read=106233 bytes_retransmit=9 bytes_invalid=0 send_seq=1657 receive_seq=1657 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997057 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5815 bytes_read=205306 bytes_retransmit=9 bytes_invalid=0 send_seq=920 receive_seq=920 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997248 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6409 bytes_read=19100 bytes_retransmit=9 bytes_invalid=0 send_seq=915 receive_seq=915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999364 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49485 bytes_read=500461 bytes_retransmit=0 bytes_invalid=0 send_seq=4552 receive_seq=4552 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998418 coil_temp=17.6 refs=0 mcu_temp=20.91 supply_voltage=3.012 th0: temp=48.1 th1: temp=47.1 th2: temp=48.9 th3: temp=47.1 sysload=0.14 cputime=102.477 memavail=7406940 print_time=847.021 buffer_time=2.117 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 823.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9450222 bytes_read=1147714 bytes_retransmit=9 bytes_invalid=0 send_seq=165465 receive_seq=165465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=41521 freq=400016195 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5662 bytes_read=19479 bytes_retransmit=0 bytes_invalid=0 send_seq=915 receive_seq=915 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999002 adj=49996872 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47600 bytes_read=1570139 bytes_retransmit=9 bytes_invalid=0 send_seq=6435 receive_seq=6435 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997406 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14754 bytes_read=106347 bytes_retransmit=9 bytes_invalid=0 send_seq=1658 receive_seq=1658 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997193 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5821 bytes_read=205570 bytes_retransmit=9 bytes_invalid=0 send_seq=921 receive_seq=921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997351 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6415 bytes_read=19116 bytes_retransmit=9 bytes_invalid=0 send_seq=916 receive_seq=916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999387 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49491 bytes_read=500817 bytes_retransmit=0 bytes_invalid=0 send_seq=4553 receive_seq=4553 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998478 coil_temp=17.6 refs=0 mcu_temp=20.91 supply_voltage=3.012 th0: temp=48.0 th1: temp=46.9 th2: temp=48.7 th3: temp=46.9 sysload=0.14 cputime=102.626 memavail=7406940 print_time=848.098 buffer_time=2.193 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 824.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9474988 bytes_read=1150078 bytes_retransmit=9 bytes_invalid=0 send_seq=165870 receive_seq=165870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=43377 freq=400016143 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5668 bytes_read=19495 bytes_retransmit=0 bytes_invalid=0 send_seq=916 receive_seq=916 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999004 adj=49996849 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47676 bytes_read=1573195 bytes_retransmit=9 bytes_invalid=0 send_seq=6446 receive_seq=6446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997342 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14760 bytes_read=106461 bytes_retransmit=9 bytes_invalid=0 send_seq=1659 receive_seq=1659 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997153 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5827 bytes_read=205804 bytes_retransmit=9 bytes_invalid=0 send_seq=922 receive_seq=922 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999535 adj=47997375 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6421 bytes_read=19132 bytes_retransmit=9 bytes_invalid=0 send_seq=917 receive_seq=917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999398 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49497 bytes_read=501173 bytes_retransmit=0 bytes_invalid=0 send_seq=4554 receive_seq=4554 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998464 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.0 th1: temp=47.1 th2: temp=48.8 th3: temp=47.0 sysload=0.14 cputime=102.774 memavail=7406720 print_time=849.174 buffer_time=2.269 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 825.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9499805 bytes_read=1152444 bytes_retransmit=9 bytes_invalid=0 send_seq=166278 receive_seq=166278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=45203 freq=400016106 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5674 bytes_read=19511 bytes_retransmit=0 bytes_invalid=0 send_seq=917 receive_seq=917 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999006 adj=49996978 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47752 bytes_read=1576268 bytes_retransmit=9 bytes_invalid=0 send_seq=6457 receive_seq=6457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997488 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14766 bytes_read=106575 bytes_retransmit=9 bytes_invalid=0 send_seq=1660 receive_seq=1660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997374 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5833 bytes_read=206098 bytes_retransmit=9 bytes_invalid=0 send_seq=923 receive_seq=923 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997490 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6427 bytes_read=19148 bytes_retransmit=9 bytes_invalid=0 send_seq=918 receive_seq=918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999420 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49503 bytes_read=501529 bytes_retransmit=0 bytes_invalid=0 send_seq=4555 receive_seq=4555 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998548 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.1 th1: temp=47.3 th2: temp=48.7 th3: temp=47.0 sysload=0.14 cputime=102.923 memavail=7405732 print_time=850.251 buffer_time=2.344 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 826.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9524594 bytes_read=1154779 bytes_retransmit=9 bytes_invalid=0 send_seq=166684 receive_seq=166684 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=47059 freq=400016063 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5680 bytes_read=19527 bytes_retransmit=0 bytes_invalid=0 send_seq=918 receive_seq=918 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999008 adj=49997054 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47828 bytes_read=1579356 bytes_retransmit=9 bytes_invalid=0 send_seq=6468 receive_seq=6468 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997573 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14772 bytes_read=106689 bytes_retransmit=9 bytes_invalid=0 send_seq=1661 receive_seq=1661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997454 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5839 bytes_read=206332 bytes_retransmit=9 bytes_invalid=0 send_seq=924 receive_seq=924 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997576 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6433 bytes_read=19164 bytes_retransmit=9 bytes_invalid=0 send_seq=919 receive_seq=919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49509 bytes_read=501885 bytes_retransmit=0 bytes_invalid=0 send_seq=4556 receive_seq=4556 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998596 coil_temp=17.6 refs=0 mcu_temp=20.91 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.3 th2: temp=49.0 th3: temp=46.9 sysload=0.12 cputime=103.070 memavail=7405732 print_time=851.327 buffer_time=2.419 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 827.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9549520 bytes_read=1157148 bytes_retransmit=9 bytes_invalid=0 send_seq=167092 receive_seq=167090 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=48777 freq=400016043 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5686 bytes_read=19543 bytes_retransmit=0 bytes_invalid=0 send_seq=919 receive_seq=919 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999010 adj=49997122 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47897 bytes_read=1582391 bytes_retransmit=9 bytes_invalid=0 send_seq=6478 receive_seq=6478 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997641 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14778 bytes_read=106789 bytes_retransmit=9 bytes_invalid=0 send_seq=1662 receive_seq=1662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997533 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5845 bytes_read=206566 bytes_retransmit=9 bytes_invalid=0 send_seq=925 receive_seq=925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6439 bytes_read=19191 bytes_retransmit=9 bytes_invalid=0 send_seq=920 receive_seq=920 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49515 bytes_read=502241 bytes_retransmit=0 bytes_invalid=0 send_seq=4557 receive_seq=4557 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998636 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.0 th1: temp=47.2 th2: temp=49.0 th3: temp=47.0 sysload=0.12 cputime=103.213 memavail=7405732 print_time=852.404 buffer_time=2.492 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 828.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9574262 bytes_read=1159498 bytes_retransmit=9 bytes_invalid=0 send_seq=167498 receive_seq=167498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=38475 freq=400016006 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5692 bytes_read=19572 bytes_retransmit=0 bytes_invalid=0 send_seq=920 receive_seq=920 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999011 adj=49997141 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47973 bytes_read=1585462 bytes_retransmit=9 bytes_invalid=0 send_seq=6489 receive_seq=6489 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997657 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14784 bytes_read=106903 bytes_retransmit=9 bytes_invalid=0 send_seq=1663 receive_seq=1663 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997544 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=5851 bytes_read=206875 bytes_retransmit=9 bytes_invalid=0 send_seq=926 receive_seq=926 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6445 bytes_read=19207 bytes_retransmit=9 bytes_invalid=0 send_seq=921 receive_seq=921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49521 bytes_read=502597 bytes_retransmit=0 bytes_invalid=0 send_seq=4558 receive_seq=4558 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998646 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=47.8 th1: temp=47.2 th2: temp=48.9 th3: temp=47.1 sysload=0.12 cputime=103.341 memavail=7405732 print_time=852.942 buffer_time=2.030 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 829.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9599046 bytes_read=1161833 bytes_retransmit=9 bytes_invalid=0 send_seq=167903 receive_seq=167903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=40331 freq=400015982 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5698 bytes_read=19588 bytes_retransmit=0 bytes_invalid=0 send_seq=921 receive_seq=921 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999013 adj=49997216 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48049 bytes_read=1588593 bytes_retransmit=9 bytes_invalid=0 send_seq=6500 receive_seq=6500 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997788 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14790 bytes_read=107031 bytes_retransmit=9 bytes_invalid=0 send_seq=1664 receive_seq=1664 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997621 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=5857 bytes_read=207109 bytes_retransmit=9 bytes_invalid=0 send_seq=927 receive_seq=927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999535 adj=47997704 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6451 bytes_read=19223 bytes_retransmit=9 bytes_invalid=0 send_seq=922 receive_seq=922 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49527 bytes_read=502953 bytes_retransmit=0 bytes_invalid=0 send_seq=4559 receive_seq=4559 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998682 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=47.9 th1: temp=47.5 th2: temp=48.8 th3: temp=47.1 sysload=0.12 cputime=103.491 memavail=7405732 print_time=854.018 buffer_time=2.106 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 830.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9624838 bytes_read=1164293 bytes_retransmit=9 bytes_invalid=0 send_seq=168324 receive_seq=168324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=41259 freq=400015940 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5704 bytes_read=19604 bytes_retransmit=0 bytes_invalid=0 send_seq=922 receive_seq=922 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999015 adj=49997250 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48125 bytes_read=1591649 bytes_retransmit=9 bytes_invalid=0 send_seq=6511 receive_seq=6511 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997799 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14796 bytes_read=107131 bytes_retransmit=9 bytes_invalid=0 send_seq=1665 receive_seq=1665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997658 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=5863 bytes_read=207343 bytes_retransmit=9 bytes_invalid=0 send_seq=928 receive_seq=928 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997719 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6457 bytes_read=19239 bytes_retransmit=9 bytes_invalid=0 send_seq=923 receive_seq=923 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49533 bytes_read=503309 bytes_retransmit=0 bytes_invalid=0 send_seq=4560 receive_seq=4560 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998764 coil_temp=17.6 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=47.8 th1: temp=47.4 th2: temp=48.9 th3: temp=46.9 sysload=0.12 cputime=103.640 memavail=7405732 print_time=855.095 buffer_time=2.182 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 831.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9649622 bytes_read=1166628 bytes_retransmit=9 bytes_invalid=0 send_seq=168729 receive_seq=168729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=43115 freq=400015991 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5710 bytes_read=19620 bytes_retransmit=0 bytes_invalid=0 send_seq=923 receive_seq=923 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999017 adj=49997287 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48201 bytes_read=1594738 bytes_retransmit=9 bytes_invalid=0 send_seq=6522 receive_seq=6522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997925 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14802 bytes_read=107245 bytes_retransmit=9 bytes_invalid=0 send_seq=1666 receive_seq=1666 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997678 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=5869 bytes_read=207637 bytes_retransmit=9 bytes_invalid=0 send_seq=929 receive_seq=929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997749 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6463 bytes_read=19255 bytes_retransmit=9 bytes_invalid=0 send_seq=924 receive_seq=924 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999469 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49539 bytes_read=503665 bytes_retransmit=0 bytes_invalid=0 send_seq=4561 receive_seq=4561 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998791 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.1 th1: temp=47.3 th2: temp=48.9 th3: temp=46.8 sysload=0.20 cputime=103.795 memavail=7405732 print_time=856.171 buffer_time=2.258 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 832.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9674406 bytes_read=1168963 bytes_retransmit=9 bytes_invalid=0 send_seq=169134 receive_seq=169134 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=44971 freq=400016047 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5716 bytes_read=19636 bytes_retransmit=0 bytes_invalid=0 send_seq=924 receive_seq=924 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999019 adj=49997174 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48277 bytes_read=1597809 bytes_retransmit=9 bytes_invalid=0 send_seq=6533 receive_seq=6533 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997745 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14808 bytes_read=107359 bytes_retransmit=9 bytes_invalid=0 send_seq=1667 receive_seq=1667 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000033 adj=63997589 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=5875 bytes_read=207871 bytes_retransmit=9 bytes_invalid=0 send_seq=930 receive_seq=930 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6469 bytes_read=19282 bytes_retransmit=9 bytes_invalid=0 send_seq=925 receive_seq=925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49545 bytes_read=504021 bytes_retransmit=0 bytes_invalid=0 send_seq=4562 receive_seq=4562 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998703 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.2 th1: temp=47.3 th2: temp=49.0 th3: temp=47.1 sysload=0.20 cputime=103.950 memavail=7405732 print_time=857.248 buffer_time=2.334 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 833.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9699252 bytes_read=1171332 bytes_retransmit=9 bytes_invalid=0 send_seq=169540 receive_seq=169540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=46790 freq=400016017 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5722 bytes_read=19665 bytes_retransmit=0 bytes_invalid=0 send_seq=925 receive_seq=925 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999020 adj=49997078 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48353 bytes_read=1600866 bytes_retransmit=9 bytes_invalid=0 send_seq=6544 receive_seq=6544 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997596 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14814 bytes_read=107459 bytes_retransmit=9 bytes_invalid=0 send_seq=1668 receive_seq=1668 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997436 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5881 bytes_read=208120 bytes_retransmit=9 bytes_invalid=0 send_seq=931 receive_seq=931 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6475 bytes_read=19298 bytes_retransmit=9 bytes_invalid=0 send_seq=926 receive_seq=926 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999419 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49551 bytes_read=504377 bytes_retransmit=0 bytes_invalid=0 send_seq=4563 receive_seq=4563 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998624 coil_temp=17.6 refs=0 mcu_temp=20.91 supply_voltage=3.012 th0: temp=47.9 th1: temp=47.1 th2: temp=48.7 th3: temp=47.0 sysload=0.20 cputime=104.104 memavail=7405732 print_time=858.324 buffer_time=2.410 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 834.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9723988 bytes_read=1173667 bytes_retransmit=9 bytes_invalid=0 send_seq=169945 receive_seq=169945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=48646 freq=400016002 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5728 bytes_read=19681 bytes_retransmit=0 bytes_invalid=0 send_seq=926 receive_seq=926 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999023 adj=49997126 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48429 bytes_read=1603937 bytes_retransmit=9 bytes_invalid=0 send_seq=6555 receive_seq=6555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997639 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14820 bytes_read=107587 bytes_retransmit=9 bytes_invalid=0 send_seq=1669 receive_seq=1669 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5887 bytes_read=208414 bytes_retransmit=9 bytes_invalid=0 send_seq=932 receive_seq=932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6481 bytes_read=19314 bytes_retransmit=9 bytes_invalid=0 send_seq=927 receive_seq=927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49557 bytes_read=504733 bytes_retransmit=0 bytes_invalid=0 send_seq=4564 receive_seq=4564 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998640 coil_temp=17.6 refs=0 mcu_temp=20.91 supply_voltage=3.012 th0: temp=48.2 th1: temp=47.0 th2: temp=48.9 th3: temp=47.0 sysload=0.20 cputime=104.256 memavail=7405732 print_time=859.401 buffer_time=2.485 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 835.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9748858 bytes_read=1176033 bytes_retransmit=9 bytes_invalid=0 send_seq=170353 receive_seq=170353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=38273 freq=400015970 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5734 bytes_read=19697 bytes_retransmit=0 bytes_invalid=0 send_seq=927 receive_seq=927 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999023 adj=49997148 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48505 bytes_read=1607009 bytes_retransmit=9 bytes_invalid=0 send_seq=6566 receive_seq=6566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997651 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14826 bytes_read=107701 bytes_retransmit=9 bytes_invalid=0 send_seq=1670 receive_seq=1670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997495 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5893 bytes_read=208648 bytes_retransmit=9 bytes_invalid=0 send_seq=933 receive_seq=933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6487 bytes_read=19330 bytes_retransmit=9 bytes_invalid=0 send_seq=928 receive_seq=928 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49563 bytes_read=505089 bytes_retransmit=0 bytes_invalid=0 send_seq=4565 receive_seq=4565 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998649 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.5 th2: temp=48.6 th3: temp=47.2 sysload=0.20 cputime=104.393 memavail=7405780 print_time=859.939 buffer_time=2.023 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 836.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9773647 bytes_read=1178398 bytes_retransmit=9 bytes_invalid=0 send_seq=170759 receive_seq=170759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=40129 freq=400016030 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5740 bytes_read=19713 bytes_retransmit=0 bytes_invalid=0 send_seq=928 receive_seq=928 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999025 adj=49997202 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48581 bytes_read=1610142 bytes_retransmit=9 bytes_invalid=0 send_seq=6577 receive_seq=6577 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997713 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14832 bytes_read=107801 bytes_retransmit=9 bytes_invalid=0 send_seq=1671 receive_seq=1671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997540 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5899 bytes_read=208882 bytes_retransmit=9 bytes_invalid=0 send_seq=934 receive_seq=934 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997714 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6493 bytes_read=19346 bytes_retransmit=9 bytes_invalid=0 send_seq=929 receive_seq=929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49569 bytes_read=505445 bytes_retransmit=0 bytes_invalid=0 send_seq=4566 receive_seq=4566 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998669 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=48.0 th1: temp=47.3 th2: temp=48.9 th3: temp=47.0 sysload=0.18 cputime=104.544 memavail=7405780 print_time=861.015 buffer_time=2.099 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 837.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9799436 bytes_read=1180825 bytes_retransmit=9 bytes_invalid=0 send_seq=171183 receive_seq=171183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=41057 freq=400016114 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5746 bytes_read=19729 bytes_retransmit=0 bytes_invalid=0 send_seq=929 receive_seq=929 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999028 adj=49997108 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48657 bytes_read=1613226 bytes_retransmit=9 bytes_invalid=0 send_seq=6588 receive_seq=6588 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997563 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14838 bytes_read=107915 bytes_retransmit=9 bytes_invalid=0 send_seq=1672 receive_seq=1672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997409 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5905 bytes_read=209176 bytes_retransmit=9 bytes_invalid=0 send_seq=935 receive_seq=935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6499 bytes_read=19373 bytes_retransmit=9 bytes_invalid=0 send_seq=930 receive_seq=930 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999418 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49575 bytes_read=505801 bytes_retransmit=0 bytes_invalid=0 send_seq=4567 receive_seq=4567 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998598 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.2 th2: temp=49.0 th3: temp=47.0 sysload=0.18 cputime=104.704 memavail=7400760 print_time=862.092 buffer_time=2.175 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 838.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9824220 bytes_read=1183160 bytes_retransmit=9 bytes_invalid=0 send_seq=171588 receive_seq=171588 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=42913 freq=400016087 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5752 bytes_read=19745 bytes_retransmit=0 bytes_invalid=0 send_seq=930 receive_seq=930 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999031 adj=49996993 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48733 bytes_read=1616285 bytes_retransmit=9 bytes_invalid=0 send_seq=6599 receive_seq=6599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997455 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14844 bytes_read=108029 bytes_retransmit=9 bytes_invalid=0 send_seq=1673 receive_seq=1673 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997246 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5911 bytes_read=209425 bytes_retransmit=9 bytes_invalid=0 send_seq=936 receive_seq=936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997508 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6505 bytes_read=19389 bytes_retransmit=9 bytes_invalid=0 send_seq=931 receive_seq=931 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999389 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49581 bytes_read=506157 bytes_retransmit=0 bytes_invalid=0 send_seq=4568 receive_seq=4568 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998521 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=48.1 th1: temp=47.2 th2: temp=49.2 th3: temp=47.2 sysload=0.18 cputime=104.856 memavail=7407140 print_time=863.168 buffer_time=2.251 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 839.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9849004 bytes_read=1185524 bytes_retransmit=9 bytes_invalid=0 send_seq=171993 receive_seq=171993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=44769 freq=400016060 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5758 bytes_read=19774 bytes_retransmit=0 bytes_invalid=0 send_seq=931 receive_seq=931 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999032 adj=49997079 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48802 bytes_read=1619319 bytes_retransmit=9 bytes_invalid=0 send_seq=6609 receive_seq=6609 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997561 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14850 bytes_read=108143 bytes_retransmit=9 bytes_invalid=0 send_seq=1674 receive_seq=1674 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997331 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5917 bytes_read=209659 bytes_retransmit=9 bytes_invalid=0 send_seq=937 receive_seq=937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997570 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6511 bytes_read=19405 bytes_retransmit=9 bytes_invalid=0 send_seq=932 receive_seq=932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999407 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49587 bytes_read=506513 bytes_retransmit=0 bytes_invalid=0 send_seq=4569 receive_seq=4569 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998565 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=48.2 th1: temp=47.5 th2: temp=49.0 th3: temp=47.1 sysload=0.18 cputime=105.002 memavail=7407140 print_time=864.245 buffer_time=2.327 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 840.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9873798 bytes_read=1187880 bytes_retransmit=9 bytes_invalid=0 send_seq=172400 receive_seq=172399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=46625 freq=400016220 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5764 bytes_read=19790 bytes_retransmit=0 bytes_invalid=0 send_seq=932 receive_seq=932 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999033 adj=49997116 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48878 bytes_read=1622404 bytes_retransmit=9 bytes_invalid=0 send_seq=6620 receive_seq=6620 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997598 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14856 bytes_read=108271 bytes_retransmit=9 bytes_invalid=0 send_seq=1675 receive_seq=1675 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997403 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5923 bytes_read=209953 bytes_retransmit=9 bytes_invalid=0 send_seq=938 receive_seq=938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997612 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6517 bytes_read=19421 bytes_retransmit=9 bytes_invalid=0 send_seq=933 receive_seq=933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999421 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49593 bytes_read=506869 bytes_retransmit=0 bytes_invalid=0 send_seq=4570 receive_seq=4570 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998594 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=48.0 th1: temp=47.2 th2: temp=49.1 th3: temp=47.0 sysload=0.18 cputime=105.150 memavail=7407140 print_time=865.321 buffer_time=2.403 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 841.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9898592 bytes_read=1190225 bytes_retransmit=9 bytes_invalid=0 send_seq=172807 receive_seq=172806 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=48481 freq=400016166 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5770 bytes_read=19806 bytes_retransmit=0 bytes_invalid=0 send_seq=933 receive_seq=933 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999034 adj=49996882 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48954 bytes_read=1625479 bytes_retransmit=9 bytes_invalid=0 send_seq=6631 receive_seq=6631 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997299 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14862 bytes_read=108371 bytes_retransmit=9 bytes_invalid=0 send_seq=1676 receive_seq=1676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997125 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5929 bytes_read=210187 bytes_retransmit=9 bytes_invalid=0 send_seq=939 receive_seq=939 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997389 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6523 bytes_read=19437 bytes_retransmit=9 bytes_invalid=0 send_seq=934 receive_seq=934 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999369 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49599 bytes_read=507225 bytes_retransmit=0 bytes_invalid=0 send_seq=4571 receive_seq=4571 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998450 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=48.2 th1: temp=47.1 th2: temp=49.2 th3: temp=47.1 sysload=0.16 cputime=105.293 memavail=7407140 print_time=866.398 buffer_time=2.479 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 842.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9923409 bytes_read=1192604 bytes_retransmit=9 bytes_invalid=0 send_seq=173214 receive_seq=173214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=38108 freq=400016119 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5776 bytes_read=19822 bytes_retransmit=0 bytes_invalid=0 send_seq=934 receive_seq=934 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999035 adj=49996989 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49030 bytes_read=1628535 bytes_retransmit=9 bytes_invalid=0 send_seq=6642 receive_seq=6642 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997438 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14868 bytes_read=108471 bytes_retransmit=9 bytes_invalid=0 send_seq=1677 receive_seq=1677 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997263 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5935 bytes_read=210421 bytes_retransmit=9 bytes_invalid=0 send_seq=940 receive_seq=940 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997491 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6529 bytes_read=19464 bytes_retransmit=9 bytes_invalid=0 send_seq=935 receive_seq=935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999398 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49605 bytes_read=507581 bytes_retransmit=0 bytes_invalid=0 send_seq=4572 receive_seq=4572 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998523 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=48.2 th1: temp=47.4 th2: temp=48.7 th3: temp=47.2 sysload=0.16 cputime=105.429 memavail=7407140 print_time=866.936 buffer_time=2.017 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 843.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9948160 bytes_read=1194949 bytes_retransmit=9 bytes_invalid=0 send_seq=173621 receive_seq=173621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=39964 freq=400016073 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5782 bytes_read=19838 bytes_retransmit=0 bytes_invalid=0 send_seq=935 receive_seq=935 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999037 adj=49997078 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49106 bytes_read=1631620 bytes_retransmit=9 bytes_invalid=0 send_seq=6653 receive_seq=6653 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997538 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14874 bytes_read=108599 bytes_retransmit=9 bytes_invalid=0 send_seq=1678 receive_seq=1678 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997342 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5941 bytes_read=210730 bytes_retransmit=9 bytes_invalid=0 send_seq=941 receive_seq=941 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997554 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6535 bytes_read=19480 bytes_retransmit=9 bytes_invalid=0 send_seq=936 receive_seq=936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999415 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49611 bytes_read=507937 bytes_retransmit=0 bytes_invalid=0 send_seq=4573 receive_seq=4573 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998566 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=48.4 th1: temp=47.2 th2: temp=49.0 th3: temp=47.3 sysload=0.16 cputime=105.582 memavail=7407140 print_time=868.012 buffer_time=2.093 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 844.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9973905 bytes_read=1197374 bytes_retransmit=9 bytes_invalid=0 send_seq=174044 receive_seq=174044 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=40959 freq=400016045 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5788 bytes_read=19867 bytes_retransmit=0 bytes_invalid=0 send_seq=936 receive_seq=936 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999040 adj=49997165 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49182 bytes_read=1634734 bytes_retransmit=9 bytes_invalid=0 send_seq=6664 receive_seq=6664 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997634 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14880 bytes_read=108713 bytes_retransmit=9 bytes_invalid=0 send_seq=1679 receive_seq=1679 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997430 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5947 bytes_read=210964 bytes_retransmit=9 bytes_invalid=0 send_seq=942 receive_seq=942 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6541 bytes_read=19496 bytes_retransmit=9 bytes_invalid=0 send_seq=937 receive_seq=937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49617 bytes_read=508293 bytes_retransmit=0 bytes_invalid=0 send_seq=4574 receive_seq=4574 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998616 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=48.1 th1: temp=47.1 th2: temp=49.0 th3: temp=47.1 sysload=0.16 cputime=105.735 memavail=7407140 print_time=869.089 buffer_time=2.169 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 845.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=9998684 bytes_read=1199749 bytes_retransmit=9 bytes_invalid=0 send_seq=174448 receive_seq=174448 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=42815 freq=400016012 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5794 bytes_read=19883 bytes_retransmit=0 bytes_invalid=0 send_seq=937 receive_seq=937 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999041 adj=49997208 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49258 bytes_read=1637793 bytes_retransmit=9 bytes_invalid=0 send_seq=6675 receive_seq=6675 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997670 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14886 bytes_read=108813 bytes_retransmit=9 bytes_invalid=0 send_seq=1680 receive_seq=1680 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997481 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5953 bytes_read=211198 bytes_retransmit=9 bytes_invalid=0 send_seq=943 receive_seq=943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6547 bytes_read=19512 bytes_retransmit=9 bytes_invalid=0 send_seq=938 receive_seq=938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49623 bytes_read=508649 bytes_retransmit=0 bytes_invalid=0 send_seq=4575 receive_seq=4575 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998636 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=48.2 th1: temp=47.4 th2: temp=49.0 th3: temp=47.1 sysload=0.16 cputime=105.884 memavail=7406896 print_time=870.165 buffer_time=2.246 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 846.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10023473 bytes_read=1202089 bytes_retransmit=9 bytes_invalid=0 send_seq=174854 receive_seq=174854 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=44671 freq=400015998 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5800 bytes_read=19899 bytes_retransmit=0 bytes_invalid=0 send_seq=938 receive_seq=938 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999045 adj=49997240 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49334 bytes_read=1640895 bytes_retransmit=9 bytes_invalid=0 send_seq=6686 receive_seq=6686 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997707 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14892 bytes_read=108941 bytes_retransmit=9 bytes_invalid=0 send_seq=1681 receive_seq=1681 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997525 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5959 bytes_read=211492 bytes_retransmit=9 bytes_invalid=0 send_seq=944 receive_seq=944 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6553 bytes_read=19528 bytes_retransmit=9 bytes_invalid=0 send_seq=939 receive_seq=939 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49629 bytes_read=509005 bytes_retransmit=0 bytes_invalid=0 send_seq=4576 receive_seq=4576 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998664 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=48.3 th1: temp=47.2 th2: temp=49.1 th3: temp=47.1 sysload=0.15 cputime=106.037 memavail=7406896 print_time=871.242 buffer_time=2.322 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 847.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10048245 bytes_read=1204425 bytes_retransmit=9 bytes_invalid=0 send_seq=175260 receive_seq=175260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=46527 freq=400016040 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5806 bytes_read=19915 bytes_retransmit=0 bytes_invalid=0 send_seq=939 receive_seq=939 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999046 adj=49997260 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49410 bytes_read=1643952 bytes_retransmit=9 bytes_invalid=0 send_seq=6697 receive_seq=6697 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997792 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14898 bytes_read=109041 bytes_retransmit=9 bytes_invalid=0 send_seq=1682 receive_seq=1682 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=5965 bytes_read=211726 bytes_retransmit=9 bytes_invalid=0 send_seq=945 receive_seq=945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6559 bytes_read=19555 bytes_retransmit=9 bytes_invalid=0 send_seq=940 receive_seq=940 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49635 bytes_read=509361 bytes_retransmit=0 bytes_invalid=0 send_seq=4577 receive_seq=4577 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998662 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=48.0 th1: temp=47.2 th2: temp=48.9 th3: temp=47.2 sysload=0.15 cputime=106.187 memavail=7406896 print_time=872.318 buffer_time=2.398 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 848.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10073102 bytes_read=1206798 bytes_retransmit=9 bytes_invalid=0 send_seq=175668 receive_seq=175667 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=48349 freq=400016015 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5812 bytes_read=19931 bytes_retransmit=0 bytes_invalid=0 send_seq=940 receive_seq=940 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999047 adj=49997165 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49486 bytes_read=1647007 bytes_retransmit=9 bytes_invalid=0 send_seq=6708 receive_seq=6708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997666 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14904 bytes_read=109140 bytes_retransmit=9 bytes_invalid=0 send_seq=1683 receive_seq=1683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000018 adj=63997428 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=5971 bytes_read=211975 bytes_retransmit=9 bytes_invalid=0 send_seq=946 receive_seq=946 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997604 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6565 bytes_read=19571 bytes_retransmit=9 bytes_invalid=0 send_seq=941 receive_seq=941 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49641 bytes_read=509717 bytes_retransmit=0 bytes_invalid=0 send_seq=4578 receive_seq=4578 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998615 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=48.0 th1: temp=47.4 th2: temp=49.2 th3: temp=47.1 sysload=0.15 cputime=106.341 memavail=7406896 print_time=873.395 buffer_time=2.474 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 849.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10097855 bytes_read=1209143 bytes_retransmit=9 bytes_invalid=0 send_seq=176074 receive_seq=176074 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=38011 freq=400016052 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5818 bytes_read=19960 bytes_retransmit=0 bytes_invalid=0 send_seq=941 receive_seq=941 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999047 adj=49997179 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49562 bytes_read=1650075 bytes_retransmit=9 bytes_invalid=0 send_seq=6719 receive_seq=6719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997684 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14910 bytes_read=109274 bytes_retransmit=9 bytes_invalid=0 send_seq=1684 receive_seq=1684 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000017 adj=63997466 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=5977 bytes_read=212269 bytes_retransmit=9 bytes_invalid=0 send_seq=947 receive_seq=947 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999535 adj=47997630 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6571 bytes_read=19587 bytes_retransmit=9 bytes_invalid=0 send_seq=942 receive_seq=942 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999445 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49647 bytes_read=510073 bytes_retransmit=0 bytes_invalid=0 send_seq=4579 receive_seq=4579 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998637 coil_temp=17.6 refs=0 mcu_temp=20.91 supply_voltage=3.012 th0: temp=48.2 th1: temp=47.4 th2: temp=49.2 th3: temp=47.3 sysload=0.15 cputime=106.477 memavail=7406904 print_time=873.933 buffer_time=2.011 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 850.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10122712 bytes_read=1211509 bytes_retransmit=9 bytes_invalid=0 send_seq=176482 receive_seq=176482 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=39830 freq=400016223 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5824 bytes_read=19976 bytes_retransmit=0 bytes_invalid=0 send_seq=942 receive_seq=942 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999050 adj=49997133 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49631 bytes_read=1653092 bytes_retransmit=9 bytes_invalid=0 send_seq=6729 receive_seq=6729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997596 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14916 bytes_read=109367 bytes_retransmit=9 bytes_invalid=0 send_seq=1685 receive_seq=1685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997387 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=5983 bytes_read=212503 bytes_retransmit=9 bytes_invalid=0 send_seq=948 receive_seq=948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999535 adj=47997559 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6577 bytes_read=19603 bytes_retransmit=9 bytes_invalid=0 send_seq=943 receive_seq=943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49653 bytes_read=510429 bytes_retransmit=0 bytes_invalid=0 send_seq=4580 receive_seq=4580 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998601 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=49.0 th1: temp=47.3 th2: temp=49.1 th3: temp=47.0 sysload=0.15 cputime=106.625 memavail=7406904 print_time=875.009 buffer_time=2.087 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 851.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10148470 bytes_read=1213969 bytes_retransmit=9 bytes_invalid=0 send_seq=176904 receive_seq=176904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=40795 freq=400016138 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5836 bytes_read=20008 bytes_retransmit=0 bytes_invalid=0 send_seq=944 receive_seq=944 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999052 adj=49996881 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49713 bytes_read=1656164 bytes_retransmit=9 bytes_invalid=0 send_seq=6741 receive_seq=6741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997255 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14928 bytes_read=109475 bytes_retransmit=9 bytes_invalid=0 send_seq=1687 receive_seq=1687 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997149 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=5995 bytes_read=212753 bytes_retransmit=9 bytes_invalid=0 send_seq=950 receive_seq=950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997311 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6589 bytes_read=19635 bytes_retransmit=9 bytes_invalid=0 send_seq=945 receive_seq=945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999368 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49665 bytes_read=510801 bytes_retransmit=0 bytes_invalid=0 send_seq=4582 receive_seq=4582 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998446 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=48.1 th1: temp=47.4 th2: temp=49.0 th3: temp=47.3 sysload=0.14 cputime=106.778 memavail=7406928 print_time=876.086 buffer_time=2.163 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 852.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10173264 bytes_read=1216314 bytes_retransmit=9 bytes_invalid=0 send_seq=177311 receive_seq=177311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=42651 freq=400016079 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5842 bytes_read=20024 bytes_retransmit=0 bytes_invalid=0 send_seq=945 receive_seq=945 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999054 adj=49997077 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49789 bytes_read=1659288 bytes_retransmit=9 bytes_invalid=0 send_seq=6752 receive_seq=6752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997465 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14934 bytes_read=109595 bytes_retransmit=9 bytes_invalid=0 send_seq=1688 receive_seq=1688 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997351 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6001 bytes_read=213047 bytes_retransmit=9 bytes_invalid=0 send_seq=951 receive_seq=951 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997483 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6595 bytes_read=19662 bytes_retransmit=9 bytes_invalid=0 send_seq=946 receive_seq=946 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999411 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49671 bytes_read=511157 bytes_retransmit=0 bytes_invalid=0 send_seq=4583 receive_seq=4583 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998585 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=48.2 th1: temp=47.5 th2: temp=49.1 th3: temp=47.2 sysload=0.14 cputime=106.928 memavail=7406940 print_time=877.162 buffer_time=2.239 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 853.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10198053 bytes_read=1218654 bytes_retransmit=9 bytes_invalid=0 send_seq=177717 receive_seq=177717 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=44507 freq=400016045 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5848 bytes_read=20040 bytes_retransmit=0 bytes_invalid=0 send_seq=946 receive_seq=946 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999055 adj=49997170 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49865 bytes_read=1662342 bytes_retransmit=9 bytes_invalid=0 send_seq=6763 receive_seq=6763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997599 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14940 bytes_read=109695 bytes_retransmit=9 bytes_invalid=0 send_seq=1689 receive_seq=1689 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997463 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6007 bytes_read=213296 bytes_retransmit=9 bytes_invalid=0 send_seq=952 receive_seq=952 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997580 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6601 bytes_read=19678 bytes_retransmit=9 bytes_invalid=0 send_seq=947 receive_seq=947 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999434 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49677 bytes_read=511513 bytes_retransmit=0 bytes_invalid=0 send_seq=4584 receive_seq=4584 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998660 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=48.2 th1: temp=47.2 th2: temp=49.1 th3: temp=47.3 sysload=0.14 cputime=107.074 memavail=7406952 print_time=878.239 buffer_time=2.316 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 854.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10222842 bytes_read=1221023 bytes_retransmit=9 bytes_invalid=0 send_seq=178123 receive_seq=178123 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=46363 freq=400015998 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5854 bytes_read=20069 bytes_retransmit=0 bytes_invalid=0 send_seq=947 receive_seq=947 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999058 adj=49997208 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49941 bytes_read=1665398 bytes_retransmit=9 bytes_invalid=0 send_seq=6774 receive_seq=6774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997706 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14946 bytes_read=109809 bytes_retransmit=9 bytes_invalid=0 send_seq=1690 receive_seq=1690 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997512 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6013 bytes_read=213530 bytes_retransmit=9 bytes_invalid=0 send_seq=953 receive_seq=953 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999535 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6607 bytes_read=19694 bytes_retransmit=9 bytes_invalid=0 send_seq=948 receive_seq=948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49683 bytes_read=511869 bytes_retransmit=0 bytes_invalid=0 send_seq=4585 receive_seq=4585 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998678 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=48.4 th1: temp=47.3 th2: temp=49.1 th3: temp=47.2 sysload=0.14 cputime=107.220 memavail=7406728 print_time=879.315 buffer_time=2.392 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 855.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10247621 bytes_read=1223369 bytes_retransmit=9 bytes_invalid=0 send_seq=178527 receive_seq=178527 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=48219 freq=400015976 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5860 bytes_read=20085 bytes_retransmit=0 bytes_invalid=0 send_seq=948 receive_seq=948 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999059 adj=49997266 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50017 bytes_read=1668483 bytes_retransmit=9 bytes_invalid=0 send_seq=6785 receive_seq=6785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997754 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14952 bytes_read=109937 bytes_retransmit=9 bytes_invalid=0 send_seq=1691 receive_seq=1691 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997572 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6019 bytes_read=213824 bytes_retransmit=9 bytes_invalid=0 send_seq=954 receive_seq=954 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997707 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6613 bytes_read=19710 bytes_retransmit=9 bytes_invalid=0 send_seq=949 receive_seq=949 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49689 bytes_read=512225 bytes_retransmit=0 bytes_invalid=0 send_seq=4586 receive_seq=4586 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998708 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=48.2 th1: temp=47.5 th2: temp=49.1 th3: temp=47.3 sysload=0.14 cputime=107.389 memavail=7407120 print_time=880.392 buffer_time=2.467 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 856.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10272431 bytes_read=1225709 bytes_retransmit=9 bytes_invalid=0 send_seq=178933 receive_seq=178933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=37844 freq=400016049 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5866 bytes_read=20101 bytes_retransmit=0 bytes_invalid=0 send_seq=949 receive_seq=949 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999060 adj=49997267 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50093 bytes_read=1671558 bytes_retransmit=9 bytes_invalid=0 send_seq=6796 receive_seq=6796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997755 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14958 bytes_read=110037 bytes_retransmit=9 bytes_invalid=0 send_seq=1692 receive_seq=1692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000018 adj=63997579 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6025 bytes_read=214058 bytes_retransmit=9 bytes_invalid=0 send_seq=955 receive_seq=955 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997758 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6619 bytes_read=19726 bytes_retransmit=9 bytes_invalid=0 send_seq=950 receive_seq=950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49695 bytes_read=512581 bytes_retransmit=0 bytes_invalid=0 send_seq=4587 receive_seq=4587 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998717 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=48.3 th1: temp=47.5 th2: temp=49.6 th3: temp=47.3 sysload=0.13 cputime=107.519 memavail=7407124 print_time=880.930 buffer_time=2.005 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 857.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10297235 bytes_read=1228093 bytes_retransmit=9 bytes_invalid=0 send_seq=179342 receive_seq=179342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=39700 freq=400016006 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5872 bytes_read=20117 bytes_retransmit=0 bytes_invalid=0 send_seq=950 receive_seq=950 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999061 adj=49997173 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50169 bytes_read=1674616 bytes_retransmit=9 bytes_invalid=0 send_seq=6807 receive_seq=6807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997604 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14964 bytes_read=110137 bytes_retransmit=9 bytes_invalid=0 send_seq=1693 receive_seq=1693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000017 adj=63997433 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6031 bytes_read=214292 bytes_retransmit=9 bytes_invalid=0 send_seq=956 receive_seq=956 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6625 bytes_read=19753 bytes_retransmit=9 bytes_invalid=0 send_seq=951 receive_seq=951 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49701 bytes_read=512937 bytes_retransmit=0 bytes_invalid=0 send_seq=4588 receive_seq=4588 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998646 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=48.2 th1: temp=47.5 th2: temp=49.2 th3: temp=47.6 sysload=0.13 cputime=107.669 memavail=7407124 print_time=882.006 buffer_time=2.081 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 858.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10323011 bytes_read=1230503 bytes_retransmit=9 bytes_invalid=0 send_seq=179763 receive_seq=179763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=40660 freq=400015975 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5878 bytes_read=20133 bytes_retransmit=0 bytes_invalid=0 send_seq=951 receive_seq=951 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999062 adj=49997240 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50245 bytes_read=1677702 bytes_retransmit=9 bytes_invalid=0 send_seq=6818 receive_seq=6818 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997695 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=14970 bytes_read=110265 bytes_retransmit=9 bytes_invalid=0 send_seq=1694 receive_seq=1694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000018 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6037 bytes_read=214601 bytes_retransmit=9 bytes_invalid=0 send_seq=957 receive_seq=957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997773 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6631 bytes_read=19769 bytes_retransmit=9 bytes_invalid=0 send_seq=952 receive_seq=952 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49707 bytes_read=513293 bytes_retransmit=0 bytes_invalid=0 send_seq=4589 receive_seq=4589 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998689 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=48.2 th1: temp=47.4 th2: temp=49.2 th3: temp=47.1 sysload=0.13 cputime=107.821 memavail=7407124 print_time=883.083 buffer_time=2.157 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 859.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10347805 bytes_read=1232848 bytes_retransmit=9 bytes_invalid=0 send_seq=180170 receive_seq=180170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=42516 freq=400015950 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5884 bytes_read=20162 bytes_retransmit=0 bytes_invalid=0 send_seq=952 receive_seq=952 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999063 adj=49997262 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50321 bytes_read=1680816 bytes_retransmit=9 bytes_invalid=0 send_seq=6829 receive_seq=6829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997718 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14976 bytes_read=110379 bytes_retransmit=9 bytes_invalid=0 send_seq=1695 receive_seq=1695 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000016 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6043 bytes_read=214835 bytes_retransmit=9 bytes_invalid=0 send_seq=958 receive_seq=958 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997782 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6637 bytes_read=19785 bytes_retransmit=9 bytes_invalid=0 send_seq=953 receive_seq=953 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49713 bytes_read=513649 bytes_retransmit=0 bytes_invalid=0 send_seq=4590 receive_seq=4590 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998695 coil_temp=17.6 refs=0 mcu_temp=20.91 supply_voltage=3.012 th0: temp=49.0 th1: temp=47.4 th2: temp=49.4 th3: temp=47.5 sysload=0.13 cputime=107.968 memavail=7407124 print_time=884.159 buffer_time=2.234 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 860.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10372546 bytes_read=1235228 bytes_retransmit=9 bytes_invalid=0 send_seq=180575 receive_seq=180575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=44372 freq=400015913 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5890 bytes_read=20178 bytes_retransmit=0 bytes_invalid=0 send_seq=953 receive_seq=953 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999064 adj=49997267 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50397 bytes_read=1683873 bytes_retransmit=9 bytes_invalid=0 send_seq=6840 receive_seq=6840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997735 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14982 bytes_read=110479 bytes_retransmit=9 bytes_invalid=0 send_seq=1696 receive_seq=1696 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000016 adj=63997577 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6049 bytes_read=215069 bytes_retransmit=9 bytes_invalid=0 send_seq=959 receive_seq=959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997771 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6643 bytes_read=19801 bytes_retransmit=9 bytes_invalid=0 send_seq=954 receive_seq=954 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999466 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49719 bytes_read=514005 bytes_retransmit=0 bytes_invalid=0 send_seq=4591 receive_seq=4591 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998703 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.1 th1: temp=47.7 th2: temp=49.2 th3: temp=47.2 sysload=0.13 cputime=108.116 memavail=7407124 print_time=885.236 buffer_time=2.309 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 861.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10397340 bytes_read=1237573 bytes_retransmit=9 bytes_invalid=0 send_seq=180982 receive_seq=180982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=46228 freq=400015878 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5896 bytes_read=20194 bytes_retransmit=0 bytes_invalid=0 send_seq=954 receive_seq=954 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999065 adj=49997287 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50473 bytes_read=1686978 bytes_retransmit=9 bytes_invalid=0 send_seq=6851 receive_seq=6851 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997770 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14988 bytes_read=110607 bytes_retransmit=9 bytes_invalid=0 send_seq=1697 receive_seq=1697 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000015 adj=63997610 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6055 bytes_read=215363 bytes_retransmit=9 bytes_invalid=0 send_seq=960 receive_seq=960 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997818 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6649 bytes_read=19828 bytes_retransmit=9 bytes_invalid=0 send_seq=955 receive_seq=955 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999478 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=25.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49725 bytes_read=514361 bytes_retransmit=0 bytes_invalid=0 send_seq=4592 receive_seq=4592 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998720 coil_temp=17.6 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=48.3 th1: temp=47.3 th2: temp=49.1 th3: temp=47.3 sysload=0.36 cputime=108.263 memavail=7407124 print_time=886.312 buffer_time=2.385 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 862.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10422172 bytes_read=1239913 bytes_retransmit=9 bytes_invalid=0 send_seq=181388 receive_seq=181388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=48084 freq=400015849 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5902 bytes_read=20210 bytes_retransmit=0 bytes_invalid=0 send_seq=955 receive_seq=955 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999067 adj=49997301 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50542 bytes_read=1690012 bytes_retransmit=9 bytes_invalid=0 send_seq=6861 receive_seq=6861 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997806 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=14994 bytes_read=110707 bytes_retransmit=9 bytes_invalid=0 send_seq=1698 receive_seq=1698 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000014 adj=63997633 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6061 bytes_read=215597 bytes_retransmit=9 bytes_invalid=0 send_seq=961 receive_seq=961 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997812 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6655 bytes_read=19844 bytes_retransmit=9 bytes_invalid=0 send_seq=956 receive_seq=956 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999479 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49731 bytes_read=514717 bytes_retransmit=0 bytes_invalid=0 send_seq=4593 receive_seq=4593 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998726 coil_temp=17.6 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=48.5 th1: temp=47.5 th2: temp=49.4 th3: temp=47.0 sysload=0.36 cputime=108.409 memavail=7407124 print_time=887.389 buffer_time=2.461 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 863.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10446919 bytes_read=1242277 bytes_retransmit=9 bytes_invalid=0 send_seq=181793 receive_seq=181793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=37711 freq=400015826 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=5908 bytes_read=20226 bytes_retransmit=0 bytes_invalid=0 send_seq=956 receive_seq=956 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999068 adj=49997311 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50618 bytes_read=1693073 bytes_retransmit=9 bytes_invalid=0 send_seq=6872 receive_seq=6872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997813 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15000 bytes_read=110807 bytes_retransmit=9 bytes_invalid=0 send_seq=1699 receive_seq=1699 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000014 adj=63997644 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6067 bytes_read=215846 bytes_retransmit=9 bytes_invalid=0 send_seq=962 receive_seq=962 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997805 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6661 bytes_read=19860 bytes_retransmit=9 bytes_invalid=0 send_seq=957 receive_seq=957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999490 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49737 bytes_read=515073 bytes_retransmit=0 bytes_invalid=0 send_seq=4594 receive_seq=4594 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998727 coil_temp=17.6 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=48.2 th1: temp=47.5 th2: temp=49.2 th3: temp=47.3 sysload=0.36 cputime=108.537 memavail=7407124 print_time=887.927 buffer_time=1.999 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 864.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10471740 bytes_read=1244632 bytes_retransmit=9 bytes_invalid=0 send_seq=182202 receive_seq=182202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=39567 freq=400015786 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=5914 bytes_read=20255 bytes_retransmit=0 bytes_invalid=0 send_seq=957 receive_seq=957 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999070 adj=49997364 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50694 bytes_read=1696158 bytes_retransmit=9 bytes_invalid=0 send_seq=6883 receive_seq=6883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997862 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15006 bytes_read=110949 bytes_retransmit=9 bytes_invalid=0 send_seq=1700 receive_seq=1700 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000013 adj=63997680 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6073 bytes_read=216140 bytes_retransmit=9 bytes_invalid=0 send_seq=963 receive_seq=963 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997824 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6667 bytes_read=19876 bytes_retransmit=9 bytes_invalid=0 send_seq=958 receive_seq=958 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999497 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49743 bytes_read=515429 bytes_retransmit=0 bytes_invalid=0 send_seq=4595 receive_seq=4595 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998759 coil_temp=17.6 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=48.3 th1: temp=47.6 th2: temp=49.3 th3: temp=47.4 sysload=0.36 cputime=108.688 memavail=7407124 print_time=889.003 buffer_time=2.075 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 865.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10497594 bytes_read=1247068 bytes_retransmit=9 bytes_invalid=0 send_seq=182624 receive_seq=182624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400015838 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=5920 bytes_read=20271 bytes_retransmit=0 bytes_invalid=0 send_seq=958 receive_seq=958 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999071 adj=49997409 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50770 bytes_read=1699214 bytes_retransmit=9 bytes_invalid=0 send_seq=6894 receive_seq=6894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997907 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15012 bytes_read=111049 bytes_retransmit=9 bytes_invalid=0 send_seq=1701 receive_seq=1701 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000012 adj=63997728 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6079 bytes_read=216374 bytes_retransmit=9 bytes_invalid=0 send_seq=964 receive_seq=964 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997852 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6673 bytes_read=19892 bytes_retransmit=9 bytes_invalid=0 send_seq=959 receive_seq=959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999504 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49749 bytes_read=515769 bytes_retransmit=0 bytes_invalid=0 send_seq=4596 receive_seq=4596 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998778 coil_temp=17.6 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=48.3 th1: temp=47.6 th2: temp=49.1 th3: temp=47.3 sysload=0.36 cputime=108.839 memavail=7406116 print_time=890.080 buffer_time=2.151 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 866.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10522309 bytes_read=1249437 bytes_retransmit=9 bytes_invalid=0 send_seq=183030 receive_seq=183030 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=42382 freq=400015885 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=5926 bytes_read=20287 bytes_retransmit=0 bytes_invalid=0 send_seq=959 receive_seq=959 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999072 adj=49997275 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50846 bytes_read=1702288 bytes_retransmit=9 bytes_invalid=0 send_seq=6905 receive_seq=6905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997756 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15018 bytes_read=111149 bytes_retransmit=9 bytes_invalid=0 send_seq=1702 receive_seq=1702 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000012 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6085 bytes_read=216608 bytes_retransmit=9 bytes_invalid=0 send_seq=965 receive_seq=965 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997716 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6679 bytes_read=19919 bytes_retransmit=9 bytes_invalid=0 send_seq=960 receive_seq=960 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999479 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49755 bytes_read=516125 bytes_retransmit=0 bytes_invalid=0 send_seq=4597 receive_seq=4597 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998742 coil_temp=17.6 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=48.0 th1: temp=47.6 th2: temp=49.5 th3: temp=47.3 sysload=0.33 cputime=108.989 memavail=7406116 print_time=891.156 buffer_time=2.227 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 867.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10547108 bytes_read=1251787 bytes_retransmit=9 bytes_invalid=0 send_seq=183438 receive_seq=183438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=44238 freq=400015861 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=5932 bytes_read=20302 bytes_retransmit=0 bytes_invalid=0 send_seq=960 receive_seq=960 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999073 adj=49997179 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50922 bytes_read=1705431 bytes_retransmit=9 bytes_invalid=0 send_seq=6916 receive_seq=6916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997635 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15024 bytes_read=111277 bytes_retransmit=9 bytes_invalid=0 send_seq=1703 receive_seq=1703 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000011 adj=63997447 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6091 bytes_read=216902 bytes_retransmit=9 bytes_invalid=0 send_seq=966 receive_seq=966 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6685 bytes_read=19935 bytes_retransmit=9 bytes_invalid=0 send_seq=961 receive_seq=961 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49761 bytes_read=516481 bytes_retransmit=0 bytes_invalid=0 send_seq=4598 receive_seq=4598 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998669 coil_temp=17.6 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=48.5 th1: temp=47.3 th2: temp=49.3 th3: temp=47.1 sysload=0.33 cputime=109.140 memavail=7406116 print_time=892.233 buffer_time=2.304 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 868.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10571924 bytes_read=1254137 bytes_retransmit=9 bytes_invalid=0 send_seq=183846 receive_seq=183846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=46094 freq=400015827 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=5938 bytes_read=20317 bytes_retransmit=0 bytes_invalid=0 send_seq=961 receive_seq=961 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999073 adj=49997197 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50998 bytes_read=1708489 bytes_retransmit=9 bytes_invalid=0 send_seq=6927 receive_seq=6927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997685 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15030 bytes_read=111377 bytes_retransmit=9 bytes_invalid=0 send_seq=1704 receive_seq=1704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000012 adj=63997491 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6097 bytes_read=217151 bytes_retransmit=9 bytes_invalid=0 send_seq=967 receive_seq=967 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997729 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6691 bytes_read=19951 bytes_retransmit=9 bytes_invalid=0 send_seq=962 receive_seq=962 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49767 bytes_read=516837 bytes_retransmit=0 bytes_invalid=0 send_seq=4599 receive_seq=4599 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998674 coil_temp=17.6 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=48.5 th1: temp=47.4 th2: temp=49.1 th3: temp=47.4 sysload=0.33 cputime=109.291 memavail=7405892 print_time=893.309 buffer_time=2.380 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 869.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10596683 bytes_read=1256471 bytes_retransmit=9 bytes_invalid=0 send_seq=184246 receive_seq=184246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=47950 freq=400015805 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=5944 bytes_read=20345 bytes_retransmit=0 bytes_invalid=0 send_seq=962 receive_seq=962 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999076 adj=49997229 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51074 bytes_read=1711545 bytes_retransmit=9 bytes_invalid=0 send_seq=6938 receive_seq=6938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997794 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15036 bytes_read=111491 bytes_retransmit=9 bytes_invalid=0 send_seq=1705 receive_seq=1705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000012 adj=63997557 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6103 bytes_read=217385 bytes_retransmit=9 bytes_invalid=0 send_seq=968 receive_seq=968 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997750 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6697 bytes_read=19967 bytes_retransmit=9 bytes_invalid=0 send_seq=963 receive_seq=963 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999468 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49773 bytes_read=517193 bytes_retransmit=0 bytes_invalid=0 send_seq=4600 receive_seq=4600 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998697 coil_temp=17.6 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=48.2 th1: temp=47.5 th2: temp=49.5 th3: temp=47.4 sysload=0.33 cputime=109.464 memavail=7407496 print_time=894.386 buffer_time=2.456 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 870.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10621667 bytes_read=1258842 bytes_retransmit=9 bytes_invalid=0 send_seq=184655 receive_seq=184655 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=49596 freq=400015791 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=5950 bytes_read=20360 bytes_retransmit=0 bytes_invalid=0 send_seq=963 receive_seq=963 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999078 adj=49997263 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51150 bytes_read=1714629 bytes_retransmit=9 bytes_invalid=0 send_seq=6949 receive_seq=6949 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997794 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15042 bytes_read=111619 bytes_retransmit=9 bytes_invalid=0 send_seq=1706 receive_seq=1706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000013 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6109 bytes_read=217675 bytes_retransmit=9 bytes_invalid=0 send_seq=969 receive_seq=969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997744 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6703 bytes_read=19983 bytes_retransmit=9 bytes_invalid=0 send_seq=964 receive_seq=964 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999469 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49779 bytes_read=517549 bytes_retransmit=0 bytes_invalid=0 send_seq=4601 receive_seq=4601 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998705 coil_temp=17.6 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=48.5 th1: temp=47.5 th2: temp=49.2 th3: temp=47.5 sysload=0.33 cputime=109.609 memavail=7407724 print_time=895.462 buffer_time=2.525 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 871.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10646492 bytes_read=1261202 bytes_retransmit=9 bytes_invalid=0 send_seq=185065 receive_seq=185065 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=39236 freq=400015758 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=5956 bytes_read=20375 bytes_retransmit=0 bytes_invalid=0 send_seq=964 receive_seq=964 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999080 adj=49997267 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51226 bytes_read=1717702 bytes_retransmit=9 bytes_invalid=0 send_seq=6960 receive_seq=6960 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997794 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15048 bytes_read=111719 bytes_retransmit=9 bytes_invalid=0 send_seq=1707 receive_seq=1707 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997594 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6115 bytes_read=217893 bytes_retransmit=9 bytes_invalid=0 send_seq=970 receive_seq=970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997747 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6709 bytes_read=20010 bytes_retransmit=9 bytes_invalid=0 send_seq=965 receive_seq=965 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999475 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49785 bytes_read=517905 bytes_retransmit=0 bytes_invalid=0 send_seq=4602 receive_seq=4602 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998703 coil_temp=17.6 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=48.2 th1: temp=47.5 th2: temp=49.2 th3: temp=47.2 sysload=0.30 cputime=109.745 memavail=7407724 print_time=896.001 buffer_time=2.062 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 872.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10671973 bytes_read=1263626 bytes_retransmit=9 bytes_invalid=0 send_seq=185482 receive_seq=185482 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400015758 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=5962 bytes_read=20391 bytes_retransmit=0 bytes_invalid=0 send_seq=965 receive_seq=965 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999081 adj=49997341 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51302 bytes_read=1720817 bytes_retransmit=9 bytes_invalid=0 send_seq=6971 receive_seq=6971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997857 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15054 bytes_read=111819 bytes_retransmit=9 bytes_invalid=0 send_seq=1708 receive_seq=1708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997741 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6121 bytes_read=218111 bytes_retransmit=9 bytes_invalid=0 send_seq=971 receive_seq=971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997776 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6715 bytes_read=20026 bytes_retransmit=9 bytes_invalid=0 send_seq=966 receive_seq=966 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999517 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49791 bytes_read=518261 bytes_retransmit=0 bytes_invalid=0 send_seq=4603 receive_seq=4603 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998732 coil_temp=17.6 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=48.3 th1: temp=47.6 th2: temp=49.3 th3: temp=47.2 sysload=0.30 cputime=109.907 memavail=7406844 print_time=897.077 buffer_time=2.138 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 873.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10697062 bytes_read=1265991 bytes_retransmit=9 bytes_invalid=0 send_seq=185893 receive_seq=185893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=42052 freq=400015721 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=5968 bytes_read=20407 bytes_retransmit=0 bytes_invalid=0 send_seq=966 receive_seq=966 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999083 adj=49997328 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51378 bytes_read=1723902 bytes_retransmit=9 bytes_invalid=0 send_seq=6982 receive_seq=6982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997830 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15060 bytes_read=111947 bytes_retransmit=9 bytes_invalid=0 send_seq=1709 receive_seq=1709 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997713 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6127 bytes_read=218400 bytes_retransmit=9 bytes_invalid=0 send_seq=972 receive_seq=972 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997756 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6721 bytes_read=20042 bytes_retransmit=9 bytes_invalid=0 send_seq=967 receive_seq=967 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999512 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49797 bytes_read=518617 bytes_retransmit=0 bytes_invalid=0 send_seq=4604 receive_seq=4604 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998718 coil_temp=17.6 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=48.3 th1: temp=47.6 th2: temp=49.4 th3: temp=47.6 sysload=0.30 cputime=110.057 memavail=7406844 print_time=898.153 buffer_time=2.214 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 874.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10721823 bytes_read=1268346 bytes_retransmit=9 bytes_invalid=0 send_seq=186302 receive_seq=186302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=43908 freq=400015701 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5974 bytes_read=20436 bytes_retransmit=0 bytes_invalid=0 send_seq=967 receive_seq=967 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999083 adj=49997348 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51454 bytes_read=1726960 bytes_retransmit=9 bytes_invalid=0 send_seq=6993 receive_seq=6993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997849 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15066 bytes_read=112061 bytes_retransmit=9 bytes_invalid=0 send_seq=1710 receive_seq=1710 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997731 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6133 bytes_read=218618 bytes_retransmit=9 bytes_invalid=0 send_seq=973 receive_seq=973 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997792 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6727 bytes_read=20058 bytes_retransmit=9 bytes_invalid=0 send_seq=968 receive_seq=968 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999505 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49803 bytes_read=518973 bytes_retransmit=0 bytes_invalid=0 send_seq=4605 receive_seq=4605 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998732 coil_temp=17.6 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=48.0 th1: temp=47.6 th2: temp=48.9 th3: temp=47.4 sysload=0.30 cputime=110.206 memavail=7408408 print_time=899.230 buffer_time=2.290 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 875.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10746617 bytes_read=1270736 bytes_retransmit=9 bytes_invalid=0 send_seq=186709 receive_seq=186709 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=45764 freq=400015862 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5980 bytes_read=20452 bytes_retransmit=0 bytes_invalid=0 send_seq=968 receive_seq=968 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999084 adj=49997334 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51523 bytes_read=1729994 bytes_retransmit=9 bytes_invalid=0 send_seq=7003 receive_seq=7003 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997837 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15072 bytes_read=112161 bytes_retransmit=9 bytes_invalid=0 send_seq=1711 receive_seq=1711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997712 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6139 bytes_read=218836 bytes_retransmit=9 bytes_invalid=0 send_seq=974 receive_seq=974 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997776 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6733 bytes_read=20074 bytes_retransmit=9 bytes_invalid=0 send_seq=969 receive_seq=969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999495 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49809 bytes_read=519329 bytes_retransmit=0 bytes_invalid=0 send_seq=4606 receive_seq=4606 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998725 coil_temp=17.6 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=48.4 th1: temp=47.5 th2: temp=49.3 th3: temp=47.5 sysload=0.30 cputime=110.353 memavail=7407456 print_time=900.306 buffer_time=2.366 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 876.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10771411 bytes_read=1273081 bytes_retransmit=9 bytes_invalid=0 send_seq=187116 receive_seq=187116 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=47620 freq=400016066 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5986 bytes_read=20468 bytes_retransmit=0 bytes_invalid=0 send_seq=969 receive_seq=969 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999086 adj=49997074 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51599 bytes_read=1733096 bytes_retransmit=9 bytes_invalid=0 send_seq=7014 receive_seq=7014 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997505 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15078 bytes_read=112289 bytes_retransmit=9 bytes_invalid=0 send_seq=1712 receive_seq=1712 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997369 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6145 bytes_read=219121 bytes_retransmit=9 bytes_invalid=0 send_seq=975 receive_seq=975 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997571 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6739 bytes_read=20101 bytes_retransmit=9 bytes_invalid=0 send_seq=970 receive_seq=970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49815 bytes_read=519685 bytes_retransmit=0 bytes_invalid=0 send_seq=4607 receive_seq=4607 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998565 coil_temp=17.6 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=48.3 th1: temp=47.4 th2: temp=49.1 th3: temp=47.5 sysload=0.36 cputime=110.504 memavail=7407456 print_time=901.383 buffer_time=2.442 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 877.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10796218 bytes_read=1275416 bytes_retransmit=9 bytes_invalid=0 send_seq=187521 receive_seq=187521 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=49463 freq=400016271 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5992 bytes_read=20484 bytes_retransmit=0 bytes_invalid=0 send_seq=970 receive_seq=970 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999087 adj=49996817 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51675 bytes_read=1736152 bytes_retransmit=9 bytes_invalid=0 send_seq=7025 receive_seq=7025 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997169 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15084 bytes_read=112389 bytes_retransmit=9 bytes_invalid=0 send_seq=1713 receive_seq=1713 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997034 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6151 bytes_read=219355 bytes_retransmit=9 bytes_invalid=0 send_seq=976 receive_seq=976 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997312 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6745 bytes_read=20117 bytes_retransmit=9 bytes_invalid=0 send_seq=971 receive_seq=971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999367 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49821 bytes_read=520041 bytes_retransmit=0 bytes_invalid=0 send_seq=4608 receive_seq=4608 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998404 coil_temp=17.6 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=48.5 th1: temp=47.6 th2: temp=49.4 th3: temp=47.5 sysload=0.36 cputime=110.648 memavail=7407476 print_time=902.459 buffer_time=2.517 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 878.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10821017 bytes_read=1277795 bytes_retransmit=9 bytes_invalid=0 send_seq=187929 receive_seq=187929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=39103 freq=400016471 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=5998 bytes_read=20500 bytes_retransmit=0 bytes_invalid=0 send_seq=971 receive_seq=971 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999088 adj=49996609 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51751 bytes_read=1739209 bytes_retransmit=9 bytes_invalid=0 send_seq=7036 receive_seq=7036 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63996902 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15090 bytes_read=112489 bytes_retransmit=9 bytes_invalid=0 send_seq=1714 receive_seq=1714 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63996789 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6157 bytes_read=219604 bytes_retransmit=9 bytes_invalid=0 send_seq=977 receive_seq=977 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997100 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6751 bytes_read=20133 bytes_retransmit=9 bytes_invalid=0 send_seq=972 receive_seq=972 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999311 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49827 bytes_read=520397 bytes_retransmit=0 bytes_invalid=0 send_seq=4609 receive_seq=4609 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998268 coil_temp=17.6 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=48.5 th1: temp=47.6 th2: temp=49.2 th3: temp=47.6 sysload=0.36 cputime=110.780 memavail=7407476 print_time=902.998 buffer_time=2.055 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 879.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10846377 bytes_read=1280183 bytes_retransmit=9 bytes_invalid=0 send_seq=188345 receive_seq=188345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400016518 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6004 bytes_read=20529 bytes_retransmit=0 bytes_invalid=0 send_seq=972 receive_seq=972 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999089 adj=49996335 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51827 bytes_read=1742295 bytes_retransmit=9 bytes_invalid=0 send_seq=7047 receive_seq=7047 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63996543 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15096 bytes_read=112631 bytes_retransmit=9 bytes_invalid=0 send_seq=1715 receive_seq=1715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63996446 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6163 bytes_read=219898 bytes_retransmit=9 bytes_invalid=0 send_seq=978 receive_seq=978 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47996820 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6757 bytes_read=20149 bytes_retransmit=9 bytes_invalid=0 send_seq=973 receive_seq=973 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999238 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49833 bytes_read=520753 bytes_retransmit=0 bytes_invalid=0 send_seq=4610 receive_seq=4610 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998079 coil_temp=17.6 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=48.2 th1: temp=47.6 th2: temp=49.3 th3: temp=47.6 sysload=0.36 cputime=110.931 memavail=7407252 print_time=904.074 buffer_time=2.132 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 880.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10871618 bytes_read=1282582 bytes_retransmit=9 bytes_invalid=0 send_seq=188760 receive_seq=188760 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=41918 freq=400016572 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6010 bytes_read=20545 bytes_retransmit=0 bytes_invalid=0 send_seq=973 receive_seq=973 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999089 adj=49996359 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51903 bytes_read=1745409 bytes_retransmit=9 bytes_invalid=0 send_seq=7058 receive_seq=7058 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63996565 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15102 bytes_read=112731 bytes_retransmit=9 bytes_invalid=0 send_seq=1716 receive_seq=1716 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63996456 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6169 bytes_read=220132 bytes_retransmit=9 bytes_invalid=0 send_seq=979 receive_seq=979 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47996833 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6763 bytes_read=20165 bytes_retransmit=9 bytes_invalid=0 send_seq=974 receive_seq=974 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999239 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49839 bytes_read=521109 bytes_retransmit=0 bytes_invalid=0 send_seq=4611 receive_seq=4611 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998089 coil_temp=17.6 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=48.4 th1: temp=47.6 th2: temp=49.4 th3: temp=47.5 sysload=0.36 cputime=111.081 memavail=7407252 print_time=905.150 buffer_time=2.208 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 881.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10896412 bytes_read=1284956 bytes_retransmit=9 bytes_invalid=0 send_seq=189167 receive_seq=189167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=43743 freq=400016627 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6016 bytes_read=20561 bytes_retransmit=0 bytes_invalid=0 send_seq=974 receive_seq=974 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999090 adj=49996436 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51979 bytes_read=1748484 bytes_retransmit=9 bytes_invalid=0 send_seq=7069 receive_seq=7069 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63996680 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15108 bytes_read=112831 bytes_retransmit=9 bytes_invalid=0 send_seq=1717 receive_seq=1717 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63996553 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6175 bytes_read=220366 bytes_retransmit=9 bytes_invalid=0 send_seq=980 receive_seq=980 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47996918 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6769 bytes_read=20192 bytes_retransmit=9 bytes_invalid=0 send_seq=975 receive_seq=975 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999273 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49845 bytes_read=521465 bytes_retransmit=0 bytes_invalid=0 send_seq=4612 receive_seq=4612 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998211 coil_temp=17.6 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=48.2 th1: temp=47.6 th2: temp=49.5 th3: temp=47.5 sysload=0.33 cputime=111.233 memavail=7407252 print_time=906.227 buffer_time=2.284 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 882.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10921176 bytes_read=1287271 bytes_retransmit=9 bytes_invalid=0 send_seq=189568 receive_seq=189568 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=45630 freq=400016549 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6022 bytes_read=20577 bytes_retransmit=0 bytes_invalid=0 send_seq=975 receive_seq=975 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999091 adj=49996489 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=52055 bytes_read=1751570 bytes_retransmit=9 bytes_invalid=0 send_seq=7080 receive_seq=7080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63996813 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15114 bytes_read=112959 bytes_retransmit=9 bytes_invalid=0 send_seq=1718 receive_seq=1718 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63996637 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6181 bytes_read=220660 bytes_retransmit=9 bytes_invalid=0 send_seq=981 receive_seq=981 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47996976 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6775 bytes_read=20208 bytes_retransmit=9 bytes_invalid=0 send_seq=976 receive_seq=976 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999282 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49851 bytes_read=521821 bytes_retransmit=0 bytes_invalid=0 send_seq=4613 receive_seq=4613 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998237 coil_temp=17.6 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=48.8 th1: temp=47.8 th2: temp=49.3 th3: temp=47.4 sysload=0.33 cputime=111.386 memavail=7407252 print_time=907.303 buffer_time=2.360 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 883.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10945965 bytes_read=1289611 bytes_retransmit=9 bytes_invalid=0 send_seq=189974 receive_seq=189974 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=47486 freq=400016461 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6028 bytes_read=20593 bytes_retransmit=0 bytes_invalid=0 send_seq=976 receive_seq=976 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999093 adj=49996725 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=52131 bytes_read=1754628 bytes_retransmit=9 bytes_invalid=0 send_seq=7091 receive_seq=7091 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997111 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15120 bytes_read=113059 bytes_retransmit=9 bytes_invalid=0 send_seq=1719 receive_seq=1719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63996920 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6187 bytes_read=220909 bytes_retransmit=9 bytes_invalid=0 send_seq=982 receive_seq=982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997190 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6781 bytes_read=20224 bytes_retransmit=9 bytes_invalid=0 send_seq=977 receive_seq=977 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999334 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49857 bytes_read=522177 bytes_retransmit=0 bytes_invalid=0 send_seq=4614 receive_seq=4614 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998377 coil_temp=17.6 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=48.4 th1: temp=47.6 th2: temp=49.5 th3: temp=47.4 sysload=0.33 cputime=111.538 memavail=7407256 print_time=908.380 buffer_time=2.436 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 884.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10970777 bytes_read=1291980 bytes_retransmit=9 bytes_invalid=0 send_seq=190380 receive_seq=190380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=49329 freq=400016555 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6034 bytes_read=20622 bytes_retransmit=0 bytes_invalid=0 send_seq=977 receive_seq=977 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999094 adj=49996932 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=52207 bytes_read=1757687 bytes_retransmit=9 bytes_invalid=0 send_seq=7102 receive_seq=7102 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997368 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15126 bytes_read=113173 bytes_retransmit=9 bytes_invalid=0 send_seq=1720 receive_seq=1720 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997165 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6193 bytes_read=221143 bytes_retransmit=9 bytes_invalid=0 send_seq=983 receive_seq=983 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997410 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6787 bytes_read=20240 bytes_retransmit=9 bytes_invalid=0 send_seq=978 receive_seq=978 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999377 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49863 bytes_read=522533 bytes_retransmit=0 bytes_invalid=0 send_seq=4615 receive_seq=4615 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998489 coil_temp=17.6 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=48.7 th1: temp=48.0 th2: temp=49.5 th3: temp=47.4 sysload=0.33 cputime=111.680 memavail=7407256 print_time=909.456 buffer_time=2.512 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 885.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=10995571 bytes_read=1294341 bytes_retransmit=9 bytes_invalid=0 send_seq=190787 receive_seq=190787 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=38969 freq=400016480 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6040 bytes_read=20638 bytes_retransmit=0 bytes_invalid=0 send_seq=978 receive_seq=978 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999096 adj=49996838 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=52283 bytes_read=1760774 bytes_retransmit=9 bytes_invalid=0 send_seq=7113 receive_seq=7113 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997238 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15132 bytes_read=113301 bytes_retransmit=9 bytes_invalid=0 send_seq=1721 receive_seq=1721 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997038 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6199 bytes_read=221437 bytes_retransmit=9 bytes_invalid=0 send_seq=984 receive_seq=984 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997308 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6793 bytes_read=20256 bytes_retransmit=9 bytes_invalid=0 send_seq=979 receive_seq=979 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999352 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49869 bytes_read=522889 bytes_retransmit=0 bytes_invalid=0 send_seq=4616 receive_seq=4616 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998423 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.3 th1: temp=47.6 th2: temp=49.6 th3: temp=47.5 sysload=0.33 cputime=111.816 memavail=7407288 print_time=909.995 buffer_time=2.050 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 886.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11020701 bytes_read=1296676 bytes_retransmit=9 bytes_invalid=0 send_seq=191192 receive_seq=191192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400016564 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6046 bytes_read=20654 bytes_retransmit=0 bytes_invalid=0 send_seq=979 receive_seq=979 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999097 adj=49996959 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=52352 bytes_read=1763825 bytes_retransmit=9 bytes_invalid=0 send_seq=7123 receive_seq=7123 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997378 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15138 bytes_read=113401 bytes_retransmit=9 bytes_invalid=0 send_seq=1722 receive_seq=1722 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997186 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6205 bytes_read=221671 bytes_retransmit=9 bytes_invalid=0 send_seq=985 receive_seq=985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997397 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6799 bytes_read=20283 bytes_retransmit=9 bytes_invalid=0 send_seq=980 receive_seq=980 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999400 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49875 bytes_read=523245 bytes_retransmit=0 bytes_invalid=0 send_seq=4617 receive_seq=4617 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998497 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.6 th1: temp=47.4 th2: temp=49.4 th3: temp=47.5 sysload=0.30 cputime=111.966 memavail=7407288 print_time=911.071 buffer_time=2.126 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 887.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11046127 bytes_read=1299100 bytes_retransmit=9 bytes_invalid=0 send_seq=191609 receive_seq=191609 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=41723 freq=400016479 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6052 bytes_read=20670 bytes_retransmit=0 bytes_invalid=0 send_seq=980 receive_seq=980 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999098 adj=49996853 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=52428 bytes_read=1766940 bytes_retransmit=9 bytes_invalid=0 send_seq=7134 receive_seq=7134 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997223 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15144 bytes_read=113501 bytes_retransmit=9 bytes_invalid=0 send_seq=1723 receive_seq=1723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000018 adj=63997036 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6211 bytes_read=221905 bytes_retransmit=9 bytes_invalid=0 send_seq=986 receive_seq=986 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997284 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6805 bytes_read=20299 bytes_retransmit=9 bytes_invalid=0 send_seq=981 receive_seq=981 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999366 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49881 bytes_read=523601 bytes_retransmit=0 bytes_invalid=0 send_seq=4618 receive_seq=4618 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998424 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.6 th1: temp=47.7 th2: temp=49.2 th3: temp=47.6 sysload=0.30 cputime=112.140 memavail=7407048 print_time=912.148 buffer_time=2.201 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 888.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11070871 bytes_read=1301395 bytes_retransmit=9 bytes_invalid=0 send_seq=192006 receive_seq=192006 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=43579 freq=400016403 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6058 bytes_read=20686 bytes_retransmit=0 bytes_invalid=0 send_seq=981 receive_seq=981 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999100 adj=49997038 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=52504 bytes_read=1770025 bytes_retransmit=9 bytes_invalid=0 send_seq=7145 receive_seq=7145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997455 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15150 bytes_read=113629 bytes_retransmit=9 bytes_invalid=0 send_seq=1724 receive_seq=1724 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000018 adj=63997267 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6217 bytes_read=222214 bytes_retransmit=9 bytes_invalid=0 send_seq=987 receive_seq=987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997459 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6811 bytes_read=20315 bytes_retransmit=9 bytes_invalid=0 send_seq=982 receive_seq=982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999408 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49887 bytes_read=523957 bytes_retransmit=0 bytes_invalid=0 send_seq=4619 receive_seq=4619 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998541 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.6 th1: temp=47.8 th2: temp=49.0 th3: temp=47.4 sysload=0.30 cputime=112.329 memavail=7406380 print_time=913.224 buffer_time=2.277 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 889.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11095665 bytes_read=1303754 bytes_retransmit=9 bytes_invalid=0 send_seq=192413 receive_seq=192413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=45435 freq=400016474 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6064 bytes_read=20715 bytes_retransmit=0 bytes_invalid=0 send_seq=982 receive_seq=982 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999101 adj=49997171 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=52580 bytes_read=1773084 bytes_retransmit=9 bytes_invalid=0 send_seq=7156 receive_seq=7156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997608 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15156 bytes_read=113743 bytes_retransmit=9 bytes_invalid=0 send_seq=1725 receive_seq=1725 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000017 adj=63997425 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6223 bytes_read=222448 bytes_retransmit=9 bytes_invalid=0 send_seq=988 receive_seq=988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6817 bytes_read=20331 bytes_retransmit=9 bytes_invalid=0 send_seq=983 receive_seq=983 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49893 bytes_read=524313 bytes_retransmit=0 bytes_invalid=0 send_seq=4620 receive_seq=4620 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998622 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.5 th1: temp=47.6 th2: temp=49.5 th3: temp=47.6 sysload=0.30 cputime=112.496 memavail=7399312 print_time=914.300 buffer_time=2.353 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 890.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11120436 bytes_read=1306119 bytes_retransmit=9 bytes_invalid=0 send_seq=192819 receive_seq=192819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=47291 freq=400016405 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6070 bytes_read=20731 bytes_retransmit=0 bytes_invalid=0 send_seq=983 receive_seq=983 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999103 adj=49997056 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=52656 bytes_read=1776140 bytes_retransmit=9 bytes_invalid=0 send_seq=7167 receive_seq=7167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997463 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15162 bytes_read=113843 bytes_retransmit=9 bytes_invalid=0 send_seq=1726 receive_seq=1726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000018 adj=63997280 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6229 bytes_read=222682 bytes_retransmit=9 bytes_invalid=0 send_seq=989 receive_seq=989 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997532 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6823 bytes_read=20347 bytes_retransmit=9 bytes_invalid=0 send_seq=984 receive_seq=984 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999403 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49899 bytes_read=524669 bytes_retransmit=0 bytes_invalid=0 send_seq=4621 receive_seq=4621 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998557 coil_temp=17.6 refs=0 mcu_temp=20.91 supply_voltage=3.012 th0: temp=48.4 th1: temp=47.7 th2: temp=49.6 th3: temp=47.6 sysload=0.30 cputime=112.647 memavail=7405464 print_time=915.377 buffer_time=2.429 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 891.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11145269 bytes_read=1308464 bytes_retransmit=9 bytes_invalid=0 send_seq=193226 receive_seq=193226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=49132 freq=400016323 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6076 bytes_read=20747 bytes_retransmit=0 bytes_invalid=0 send_seq=984 receive_seq=984 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999105 adj=49997173 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=52732 bytes_read=1779243 bytes_retransmit=9 bytes_invalid=0 send_seq=7178 receive_seq=7178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997650 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15168 bytes_read=113971 bytes_retransmit=9 bytes_invalid=0 send_seq=1727 receive_seq=1727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000018 adj=63997436 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6235 bytes_read=222976 bytes_retransmit=9 bytes_invalid=0 send_seq=990 receive_seq=990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997616 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6829 bytes_read=20374 bytes_retransmit=9 bytes_invalid=0 send_seq=985 receive_seq=985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49905 bytes_read=525025 bytes_retransmit=0 bytes_invalid=0 send_seq=4622 receive_seq=4622 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998638 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=48.8 th1: temp=47.7 th2: temp=49.5 th3: temp=47.7 sysload=0.28 cputime=112.796 memavail=7405464 print_time=916.453 buffer_time=2.505 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 892.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11170063 bytes_read=1310823 bytes_retransmit=9 bytes_invalid=0 send_seq=193633 receive_seq=193633 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=38772 freq=400016257 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6082 bytes_read=20763 bytes_retransmit=0 bytes_invalid=0 send_seq=985 receive_seq=985 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999105 adj=49997271 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=52808 bytes_read=1782300 bytes_retransmit=9 bytes_invalid=0 send_seq=7189 receive_seq=7189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997850 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15174 bytes_read=114071 bytes_retransmit=9 bytes_invalid=0 send_seq=1728 receive_seq=1728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997570 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6241 bytes_read=223210 bytes_retransmit=9 bytes_invalid=0 send_seq=991 receive_seq=991 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997700 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6835 bytes_read=20390 bytes_retransmit=9 bytes_invalid=0 send_seq=986 receive_seq=986 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=26.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49911 bytes_read=525381 bytes_retransmit=0 bytes_invalid=0 send_seq=4623 receive_seq=4623 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998693 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.5 th1: temp=47.6 th2: temp=49.6 th3: temp=47.7 sysload=0.28 cputime=112.932 memavail=7405464 print_time=916.992 buffer_time=2.042 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 893.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11195035 bytes_read=1313188 bytes_retransmit=9 bytes_invalid=0 send_seq=194041 receive_seq=194041 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400016198 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6088 bytes_read=20779 bytes_retransmit=0 bytes_invalid=0 send_seq=986 receive_seq=986 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999105 adj=49997371 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=52884 bytes_read=1785359 bytes_retransmit=9 bytes_invalid=0 send_seq=7200 receive_seq=7200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997959 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15180 bytes_read=114171 bytes_retransmit=9 bytes_invalid=0 send_seq=1729 receive_seq=1729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997700 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6247 bytes_read=223459 bytes_retransmit=9 bytes_invalid=0 send_seq=992 receive_seq=992 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997784 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6841 bytes_read=20406 bytes_retransmit=9 bytes_invalid=0 send_seq=987 receive_seq=987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999469 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49917 bytes_read=525737 bytes_retransmit=0 bytes_invalid=0 send_seq=4624 receive_seq=4624 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998750 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.5 th1: temp=47.8 th2: temp=49.7 th3: temp=47.6 sysload=0.28 cputime=113.081 memavail=7405240 print_time=918.068 buffer_time=2.119 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 894.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11220690 bytes_read=1315593 bytes_retransmit=9 bytes_invalid=0 send_seq=194461 receive_seq=194460 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=41521 freq=400016141 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6094 bytes_read=20808 bytes_retransmit=0 bytes_invalid=0 send_seq=987 receive_seq=987 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999105 adj=49997431 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=52960 bytes_read=1788445 bytes_retransmit=9 bytes_invalid=0 send_seq=7211 receive_seq=7211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63998025 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15186 bytes_read=114313 bytes_retransmit=9 bytes_invalid=0 send_seq=1730 receive_seq=1730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997794 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6253 bytes_read=223753 bytes_retransmit=9 bytes_invalid=0 send_seq=993 receive_seq=993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997846 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6847 bytes_read=20422 bytes_retransmit=9 bytes_invalid=0 send_seq=988 receive_seq=988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999484 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49923 bytes_read=526093 bytes_retransmit=0 bytes_invalid=0 send_seq=4625 receive_seq=4625 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998798 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.8 th1: temp=47.3 th2: temp=49.6 th3: temp=47.6 sysload=0.28 cputime=113.232 memavail=7405240 print_time=919.145 buffer_time=2.194 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 895.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11245417 bytes_read=1317963 bytes_retransmit=9 bytes_invalid=0 send_seq=194866 receive_seq=194866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=43444 freq=400016085 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6100 bytes_read=20824 bytes_retransmit=0 bytes_invalid=0 send_seq=988 receive_seq=988 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999107 adj=49997437 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=53036 bytes_read=1791562 bytes_retransmit=9 bytes_invalid=0 send_seq=7222 receive_seq=7222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63998022 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15192 bytes_read=114413 bytes_retransmit=9 bytes_invalid=0 send_seq=1731 receive_seq=1731 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997824 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6259 bytes_read=223987 bytes_retransmit=9 bytes_invalid=0 send_seq=994 receive_seq=994 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997869 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6853 bytes_read=20438 bytes_retransmit=9 bytes_invalid=0 send_seq=989 receive_seq=989 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999488 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49929 bytes_read=526449 bytes_retransmit=0 bytes_invalid=0 send_seq=4626 receive_seq=4626 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998809 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.5 th1: temp=47.6 th2: temp=49.8 th3: temp=47.6 sysload=0.28 cputime=113.380 memavail=7405036 print_time=920.221 buffer_time=2.270 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 896.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11270206 bytes_read=1320318 bytes_retransmit=9 bytes_invalid=0 send_seq=195272 receive_seq=195272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=45268 freq=400016044 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6106 bytes_read=20840 bytes_retransmit=0 bytes_invalid=0 send_seq=989 receive_seq=989 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999109 adj=49997459 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=53112 bytes_read=1794636 bytes_retransmit=9 bytes_invalid=0 send_seq=7233 receive_seq=7233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63998113 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15198 bytes_read=114513 bytes_retransmit=9 bytes_invalid=0 send_seq=1732 receive_seq=1732 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997836 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6265 bytes_read=224221 bytes_retransmit=9 bytes_invalid=0 send_seq=995 receive_seq=995 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997880 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6859 bytes_read=20465 bytes_retransmit=9 bytes_invalid=0 send_seq=990 receive_seq=990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999491 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49935 bytes_read=526803 bytes_retransmit=0 bytes_invalid=0 send_seq=4627 receive_seq=4627 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998832 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.5 th1: temp=47.6 th2: temp=49.8 th3: temp=47.8 sysload=0.26 cputime=113.532 memavail=7405036 print_time=921.298 buffer_time=2.347 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 897.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11295047 bytes_read=1322648 bytes_retransmit=9 bytes_invalid=0 send_seq=195677 receive_seq=195676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=47089 freq=400016008 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6112 bytes_read=20856 bytes_retransmit=0 bytes_invalid=0 send_seq=990 receive_seq=990 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999111 adj=49997464 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=53181 bytes_read=1797698 bytes_retransmit=9 bytes_invalid=0 send_seq=7243 receive_seq=7243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63998067 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15204 bytes_read=114641 bytes_retransmit=9 bytes_invalid=0 send_seq=1733 receive_seq=1733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997832 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6271 bytes_read=224515 bytes_retransmit=9 bytes_invalid=0 send_seq=996 receive_seq=996 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997876 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6865 bytes_read=20481 bytes_retransmit=9 bytes_invalid=0 send_seq=991 receive_seq=991 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999489 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49941 bytes_read=527148 bytes_retransmit=0 bytes_invalid=0 send_seq=4628 receive_seq=4628 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998816 coil_temp=17.6 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=48.5 th1: temp=47.6 th2: temp=49.7 th3: temp=47.2 sysload=0.26 cputime=113.682 memavail=7405052 print_time=922.374 buffer_time=2.422 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 898.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11319847 bytes_read=1325002 bytes_retransmit=9 bytes_invalid=0 send_seq=196082 receive_seq=196082 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=48899 freq=400015961 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6118 bytes_read=20872 bytes_retransmit=0 bytes_invalid=0 send_seq=991 receive_seq=991 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999112 adj=49997457 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=53257 bytes_read=1800756 bytes_retransmit=9 bytes_invalid=0 send_seq=7254 receive_seq=7254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63998032 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15210 bytes_read=114741 bytes_retransmit=9 bytes_invalid=0 send_seq=1734 receive_seq=1734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997809 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6277 bytes_read=224764 bytes_retransmit=9 bytes_invalid=0 send_seq=997 receive_seq=997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997860 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6871 bytes_read=20497 bytes_retransmit=9 bytes_invalid=0 send_seq=992 receive_seq=992 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999489 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49947 bytes_read=527492 bytes_retransmit=0 bytes_invalid=0 send_seq=4629 receive_seq=4629 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998806 coil_temp=17.6 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=48.5 th1: temp=47.6 th2: temp=49.4 th3: temp=47.8 sysload=0.26 cputime=113.830 memavail=7405052 print_time=923.450 buffer_time=2.495 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 899.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11344643 bytes_read=1327357 bytes_retransmit=9 bytes_invalid=0 send_seq=196488 receive_seq=196488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=38540 freq=400015932 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6124 bytes_read=20901 bytes_retransmit=0 bytes_invalid=0 send_seq=992 receive_seq=992 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999113 adj=49997464 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=53333 bytes_read=1803813 bytes_retransmit=9 bytes_invalid=0 send_seq=7265 receive_seq=7265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63998026 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15216 bytes_read=114855 bytes_retransmit=9 bytes_invalid=0 send_seq=1735 receive_seq=1735 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997812 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6283 bytes_read=224998 bytes_retransmit=9 bytes_invalid=0 send_seq=998 receive_seq=998 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997872 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6877 bytes_read=20513 bytes_retransmit=9 bytes_invalid=0 send_seq=993 receive_seq=993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999490 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49953 bytes_read=527837 bytes_retransmit=0 bytes_invalid=0 send_seq=4630 receive_seq=4630 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998808 coil_temp=17.6 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=48.5 th1: temp=48.0 th2: temp=49.6 th3: temp=47.7 sysload=0.26 cputime=113.959 memavail=7405060 print_time=923.989 buffer_time=2.034 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 900.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11369437 bytes_read=1329718 bytes_retransmit=9 bytes_invalid=0 send_seq=196895 receive_seq=196895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=40428 freq=400015881 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6130 bytes_read=20917 bytes_retransmit=0 bytes_invalid=0 send_seq=993 receive_seq=993 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999114 adj=49997522 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=53409 bytes_read=1806898 bytes_retransmit=9 bytes_invalid=0 send_seq=7276 receive_seq=7276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63998069 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15222 bytes_read=114983 bytes_retransmit=9 bytes_invalid=0 send_seq=1736 receive_seq=1736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997878 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6289 bytes_read=225292 bytes_retransmit=9 bytes_invalid=0 send_seq=999 receive_seq=999 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997901 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6883 bytes_read=20529 bytes_retransmit=9 bytes_invalid=0 send_seq=994 receive_seq=994 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999497 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49959 bytes_read=528182 bytes_retransmit=0 bytes_invalid=0 send_seq=4631 receive_seq=4631 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998839 coil_temp=17.6 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=48.5 th1: temp=47.6 th2: temp=49.5 th3: temp=47.8 sysload=0.26 cputime=114.110 memavail=7405060 print_time=925.065 buffer_time=2.110 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 901.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11395234 bytes_read=1332148 bytes_retransmit=9 bytes_invalid=0 send_seq=197317 receive_seq=197317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=41356 freq=400015835 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6136 bytes_read=20933 bytes_retransmit=0 bytes_invalid=0 send_seq=994 receive_seq=994 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999116 adj=49997565 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=53485 bytes_read=1809972 bytes_retransmit=9 bytes_invalid=0 send_seq=7287 receive_seq=7287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63998101 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15228 bytes_read=115083 bytes_retransmit=9 bytes_invalid=0 send_seq=1737 receive_seq=1737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997919 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6295 bytes_read=225526 bytes_retransmit=9 bytes_invalid=0 send_seq=1000 receive_seq=1000 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997932 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6889 bytes_read=20556 bytes_retransmit=9 bytes_invalid=0 send_seq=995 receive_seq=995 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999505 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49965 bytes_read=528527 bytes_retransmit=0 bytes_invalid=0 send_seq=4632 receive_seq=4632 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998861 coil_temp=17.6 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=48.6 th1: temp=47.8 th2: temp=49.5 th3: temp=47.7 sysload=0.24 cputime=114.262 memavail=7405060 print_time=926.142 buffer_time=2.186 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 902.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11420033 bytes_read=1334513 bytes_retransmit=9 bytes_invalid=0 send_seq=197725 receive_seq=197725 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=43212 freq=400015794 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6142 bytes_read=20949 bytes_retransmit=0 bytes_invalid=0 send_seq=995 receive_seq=995 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999117 adj=49997551 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=53561 bytes_read=1813087 bytes_retransmit=9 bytes_invalid=0 send_seq=7298 receive_seq=7298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63998078 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15234 bytes_read=115183 bytes_retransmit=9 bytes_invalid=0 send_seq=1738 receive_seq=1738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63998005 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6301 bytes_read=225760 bytes_retransmit=9 bytes_invalid=0 send_seq=1001 receive_seq=1001 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997931 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6895 bytes_read=20572 bytes_retransmit=9 bytes_invalid=0 send_seq=996 receive_seq=996 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999505 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49971 bytes_read=528872 bytes_retransmit=0 bytes_invalid=0 send_seq=4633 receive_seq=4633 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998849 coil_temp=17.6 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=48.4 th1: temp=47.7 th2: temp=49.6 th3: temp=47.5 sysload=0.24 cputime=114.409 memavail=7405060 print_time=927.218 buffer_time=2.262 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 903.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11444779 bytes_read=1336853 bytes_retransmit=9 bytes_invalid=0 send_seq=198131 receive_seq=198131 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=45068 freq=400015762 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6148 bytes_read=20965 bytes_retransmit=0 bytes_invalid=0 send_seq=996 receive_seq=996 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999118 adj=49997530 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=53637 bytes_read=1816171 bytes_retransmit=9 bytes_invalid=0 send_seq=7309 receive_seq=7309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63998065 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15240 bytes_read=115311 bytes_retransmit=9 bytes_invalid=0 send_seq=1739 receive_seq=1739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997983 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6307 bytes_read=226069 bytes_retransmit=9 bytes_invalid=0 send_seq=1002 receive_seq=1002 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997918 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6901 bytes_read=20588 bytes_retransmit=9 bytes_invalid=0 send_seq=997 receive_seq=997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999506 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49977 bytes_read=529217 bytes_retransmit=0 bytes_invalid=0 send_seq=4634 receive_seq=4634 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998835 coil_temp=17.6 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=48.7 th1: temp=47.9 th2: temp=49.9 th3: temp=47.8 sysload=0.24 cputime=114.558 memavail=7405060 print_time=928.295 buffer_time=2.338 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 904.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11469553 bytes_read=1339192 bytes_retransmit=9 bytes_invalid=0 send_seq=198534 receive_seq=198534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=46924 freq=400015735 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6154 bytes_read=20994 bytes_retransmit=0 bytes_invalid=0 send_seq=997 receive_seq=997 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999120 adj=49997511 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=53713 bytes_read=1819229 bytes_retransmit=9 bytes_invalid=0 send_seq=7320 receive_seq=7320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63998098 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15246 bytes_read=115411 bytes_retransmit=9 bytes_invalid=0 send_seq=1740 receive_seq=1740 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997920 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6313 bytes_read=226303 bytes_retransmit=9 bytes_invalid=0 send_seq=1003 receive_seq=1003 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999535 adj=47997896 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6907 bytes_read=20604 bytes_retransmit=9 bytes_invalid=0 send_seq=998 receive_seq=998 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999501 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49983 bytes_read=529562 bytes_retransmit=0 bytes_invalid=0 send_seq=4635 receive_seq=4635 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998821 coil_temp=17.6 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=48.7 th1: temp=47.8 th2: temp=49.8 th3: temp=47.9 sysload=0.24 cputime=114.714 memavail=7404828 print_time=929.371 buffer_time=2.414 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 905.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11494355 bytes_read=1341563 bytes_retransmit=9 bytes_invalid=0 send_seq=198940 receive_seq=198940 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=48777 freq=400015710 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6160 bytes_read=21010 bytes_retransmit=0 bytes_invalid=0 send_seq=998 receive_seq=998 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999120 adj=49997490 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=53789 bytes_read=1822285 bytes_retransmit=9 bytes_invalid=0 send_seq=7331 receive_seq=7331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63998118 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15252 bytes_read=115525 bytes_retransmit=9 bytes_invalid=0 send_seq=1741 receive_seq=1741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997876 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6319 bytes_read=226537 bytes_retransmit=9 bytes_invalid=0 send_seq=1004 receive_seq=1004 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997875 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6913 bytes_read=20620 bytes_retransmit=9 bytes_invalid=0 send_seq=999 receive_seq=999 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999495 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49989 bytes_read=529916 bytes_retransmit=0 bytes_invalid=0 send_seq=4636 receive_seq=4636 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998806 coil_temp=17.6 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=48.7 th1: temp=47.7 th2: temp=49.5 th3: temp=47.6 sysload=0.24 cputime=114.861 memavail=7404840 print_time=930.447 buffer_time=2.490 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 906.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11519159 bytes_read=1343908 bytes_retransmit=9 bytes_invalid=0 send_seq=199347 receive_seq=199347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=38407 freq=400015700 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6166 bytes_read=21026 bytes_retransmit=0 bytes_invalid=0 send_seq=999 receive_seq=999 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999120 adj=49997459 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=53865 bytes_read=1825387 bytes_retransmit=9 bytes_invalid=0 send_seq=7342 receive_seq=7342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63998055 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15258 bytes_read=115653 bytes_retransmit=9 bytes_invalid=0 send_seq=1742 receive_seq=1742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997889 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6325 bytes_read=226831 bytes_retransmit=9 bytes_invalid=0 send_seq=1005 receive_seq=1005 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997853 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6919 bytes_read=20647 bytes_retransmit=9 bytes_invalid=0 send_seq=1000 receive_seq=1000 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999493 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=49995 bytes_read=530272 bytes_retransmit=0 bytes_invalid=0 send_seq=4637 receive_seq=4637 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998816 coil_temp=17.6 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=48.6 th1: temp=48.1 th2: temp=49.5 th3: temp=47.8 sysload=0.22 cputime=115.004 memavail=7401072 print_time=930.986 buffer_time=2.028 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 907.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11543958 bytes_read=1346287 bytes_retransmit=9 bytes_invalid=0 send_seq=199755 receive_seq=199755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=40263 freq=400015699 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6172 bytes_read=21042 bytes_retransmit=0 bytes_invalid=0 send_seq=1000 receive_seq=1000 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999124 adj=49997474 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=53941 bytes_read=1828444 bytes_retransmit=9 bytes_invalid=0 send_seq=7353 receive_seq=7353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63998053 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15264 bytes_read=115753 bytes_retransmit=9 bytes_invalid=0 send_seq=1743 receive_seq=1743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997897 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6331 bytes_read=227065 bytes_retransmit=9 bytes_invalid=0 send_seq=1006 receive_seq=1006 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997861 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6925 bytes_read=20663 bytes_retransmit=9 bytes_invalid=0 send_seq=1001 receive_seq=1001 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999495 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50001 bytes_read=530628 bytes_retransmit=0 bytes_invalid=0 send_seq=4638 receive_seq=4638 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998817 coil_temp=17.6 refs=0 mcu_temp=20.96 supply_voltage=3.011 th0: temp=48.4 th1: temp=47.8 th2: temp=49.5 th3: temp=48.0 sysload=0.22 cputime=115.158 memavail=7407756 print_time=932.062 buffer_time=2.103 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 908.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11569760 bytes_read=1348712 bytes_retransmit=9 bytes_invalid=0 send_seq=200178 receive_seq=200178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=41222 freq=400015675 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6178 bytes_read=21058 bytes_retransmit=0 bytes_invalid=0 send_seq=1001 receive_seq=1001 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999124 adj=49997482 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=54017 bytes_read=1831500 bytes_retransmit=9 bytes_invalid=0 send_seq=7364 receive_seq=7364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63998003 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15270 bytes_read=115853 bytes_retransmit=9 bytes_invalid=0 send_seq=1744 receive_seq=1744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997870 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6337 bytes_read=227314 bytes_retransmit=9 bytes_invalid=0 send_seq=1007 receive_seq=1007 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997831 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6931 bytes_read=20679 bytes_retransmit=9 bytes_invalid=0 send_seq=1002 receive_seq=1002 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999490 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50007 bytes_read=530984 bytes_retransmit=0 bytes_invalid=0 send_seq=4639 receive_seq=4639 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998794 coil_temp=17.6 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=48.7 th1: temp=47.6 th2: temp=49.7 th3: temp=47.6 sysload=0.22 cputime=115.310 memavail=7407756 print_time=933.139 buffer_time=2.179 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 909.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11594559 bytes_read=1351062 bytes_retransmit=9 bytes_invalid=0 send_seq=200586 receive_seq=200586 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=43047 freq=400015641 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6184 bytes_read=21087 bytes_retransmit=0 bytes_invalid=0 send_seq=1002 receive_seq=1002 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999126 adj=49997445 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=54093 bytes_read=1834642 bytes_retransmit=9 bytes_invalid=0 send_seq=7375 receive_seq=7375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63998015 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15276 bytes_read=115981 bytes_retransmit=9 bytes_invalid=0 send_seq=1745 receive_seq=1745 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997836 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6343 bytes_read=227608 bytes_retransmit=9 bytes_invalid=0 send_seq=1008 receive_seq=1008 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997829 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6937 bytes_read=20695 bytes_retransmit=9 bytes_invalid=0 send_seq=1003 receive_seq=1003 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999489 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50013 bytes_read=531340 bytes_retransmit=0 bytes_invalid=0 send_seq=4640 receive_seq=4640 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998782 coil_temp=17.6 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=48.8 th1: temp=47.8 th2: temp=49.5 th3: temp=48.0 sysload=0.22 cputime=115.461 memavail=7407760 print_time=934.215 buffer_time=2.256 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 910.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11619363 bytes_read=1353462 bytes_retransmit=9 bytes_invalid=0 send_seq=200995 receive_seq=200995 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=44903 freq=400015619 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6190 bytes_read=21103 bytes_retransmit=0 bytes_invalid=0 send_seq=1003 receive_seq=1003 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999127 adj=49997464 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=54162 bytes_read=1837676 bytes_retransmit=9 bytes_invalid=0 send_seq=7385 receive_seq=7385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997988 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15282 bytes_read=116095 bytes_retransmit=9 bytes_invalid=0 send_seq=1746 receive_seq=1746 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997815 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6349 bytes_read=227842 bytes_retransmit=9 bytes_invalid=0 send_seq=1009 receive_seq=1009 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997830 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6943 bytes_read=20711 bytes_retransmit=9 bytes_invalid=0 send_seq=1004 receive_seq=1004 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999489 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50019 bytes_read=531696 bytes_retransmit=0 bytes_invalid=0 send_seq=4641 receive_seq=4641 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998782 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.5 th1: temp=48.0 th2: temp=49.6 th3: temp=47.7 sysload=0.22 cputime=115.613 memavail=7407760 print_time=935.292 buffer_time=2.332 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 911.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11644162 bytes_read=1355810 bytes_retransmit=9 bytes_invalid=0 send_seq=201403 receive_seq=201403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=46790 freq=400015634 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6196 bytes_read=21119 bytes_retransmit=0 bytes_invalid=0 send_seq=1004 receive_seq=1004 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999128 adj=49997444 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=54238 bytes_read=1840750 bytes_retransmit=9 bytes_invalid=0 send_seq=7396 receive_seq=7396 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997951 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15288 bytes_read=116195 bytes_retransmit=9 bytes_invalid=0 send_seq=1747 receive_seq=1747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997778 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6355 bytes_read=228076 bytes_retransmit=9 bytes_invalid=0 send_seq=1010 receive_seq=1010 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997833 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6949 bytes_read=20738 bytes_retransmit=9 bytes_invalid=0 send_seq=1005 receive_seq=1005 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999485 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50025 bytes_read=532052 bytes_retransmit=0 bytes_invalid=0 send_seq=4642 receive_seq=4642 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998783 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.5 th1: temp=48.0 th2: temp=49.7 th3: temp=47.8 sysload=0.20 cputime=115.760 memavail=7407760 print_time=936.368 buffer_time=2.408 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 912.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11668971 bytes_read=1358152 bytes_retransmit=9 bytes_invalid=0 send_seq=201811 receive_seq=201810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=48615 freq=400015613 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6202 bytes_read=21135 bytes_retransmit=0 bytes_invalid=0 send_seq=1005 receive_seq=1005 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999129 adj=49997376 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=54314 bytes_read=1843835 bytes_retransmit=9 bytes_invalid=0 send_seq=7407 receive_seq=7407 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997854 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15294 bytes_read=116323 bytes_retransmit=9 bytes_invalid=0 send_seq=1748 receive_seq=1748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997700 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6361 bytes_read=228370 bytes_retransmit=9 bytes_invalid=0 send_seq=1011 receive_seq=1011 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997771 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6955 bytes_read=20754 bytes_retransmit=9 bytes_invalid=0 send_seq=1006 receive_seq=1006 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999491 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50031 bytes_read=532408 bytes_retransmit=0 bytes_invalid=0 send_seq=4643 receive_seq=4643 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998746 coil_temp=17.7 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=48.9 th1: temp=47.8 th2: temp=49.7 th3: temp=47.9 sysload=0.20 cputime=115.912 memavail=7407760 print_time=937.445 buffer_time=2.484 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 913.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11693840 bytes_read=1360536 bytes_retransmit=9 bytes_invalid=0 send_seq=202219 receive_seq=202219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=38206 freq=400015594 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6208 bytes_read=21151 bytes_retransmit=0 bytes_invalid=0 send_seq=1006 receive_seq=1006 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999130 adj=49997374 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=54390 bytes_read=1846892 bytes_retransmit=9 bytes_invalid=0 send_seq=7418 receive_seq=7418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997841 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15300 bytes_read=116423 bytes_retransmit=9 bytes_invalid=0 send_seq=1749 receive_seq=1749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997687 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6367 bytes_read=228619 bytes_retransmit=9 bytes_invalid=0 send_seq=1012 receive_seq=1012 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999535 adj=47997781 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6961 bytes_read=20770 bytes_retransmit=9 bytes_invalid=0 send_seq=1007 receive_seq=1007 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999493 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50037 bytes_read=532764 bytes_retransmit=0 bytes_invalid=0 send_seq=4644 receive_seq=4644 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998746 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=48.4 th1: temp=47.9 th2: temp=49.5 th3: temp=47.7 sysload=0.20 cputime=116.042 memavail=7407760 print_time=937.983 buffer_time=2.021 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 914.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11718550 bytes_read=1362882 bytes_retransmit=9 bytes_invalid=0 send_seq=202624 receive_seq=202624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=40099 freq=400015541 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6220 bytes_read=21196 bytes_retransmit=0 bytes_invalid=0 send_seq=1008 receive_seq=1008 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999130 adj=49997411 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=54472 bytes_read=1849965 bytes_retransmit=9 bytes_invalid=0 send_seq=7430 receive_seq=7430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997859 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15312 bytes_read=116539 bytes_retransmit=9 bytes_invalid=0 send_seq=1751 receive_seq=1751 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997728 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6379 bytes_read=228869 bytes_retransmit=9 bytes_invalid=0 send_seq=1014 receive_seq=1014 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997814 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6973 bytes_read=20802 bytes_retransmit=9 bytes_invalid=0 send_seq=1009 receive_seq=1009 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999497 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50049 bytes_read=533136 bytes_retransmit=0 bytes_invalid=0 send_seq=4646 receive_seq=4646 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998765 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=48.4 th1: temp=48.0 th2: temp=49.7 th3: temp=47.8 sysload=0.20 cputime=116.194 memavail=7407760 print_time=939.059 buffer_time=2.097 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 915.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11744347 bytes_read=1365318 bytes_retransmit=9 bytes_invalid=0 send_seq=203046 receive_seq=203046 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=41027 freq=400015514 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6226 bytes_read=21212 bytes_retransmit=0 bytes_invalid=0 send_seq=1009 receive_seq=1009 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999131 adj=49997473 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=54548 bytes_read=1853049 bytes_retransmit=9 bytes_invalid=0 send_seq=7441 receive_seq=7441 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997939 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15318 bytes_read=116679 bytes_retransmit=9 bytes_invalid=0 send_seq=1752 receive_seq=1752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997848 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6385 bytes_read=229163 bytes_retransmit=9 bytes_invalid=0 send_seq=1015 receive_seq=1015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997864 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6979 bytes_read=20818 bytes_retransmit=9 bytes_invalid=0 send_seq=1010 receive_seq=1010 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999506 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50055 bytes_read=533492 bytes_retransmit=0 bytes_invalid=0 send_seq=4647 receive_seq=4647 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998825 coil_temp=17.7 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=48.7 th1: temp=47.8 th2: temp=49.8 th3: temp=47.9 sysload=0.20 cputime=116.347 memavail=7406764 print_time=940.136 buffer_time=2.173 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 916.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11769164 bytes_read=1367697 bytes_retransmit=9 bytes_invalid=0 send_seq=203454 receive_seq=203454 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=42883 freq=400015485 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6232 bytes_read=21228 bytes_retransmit=0 bytes_invalid=0 send_seq=1010 receive_seq=1010 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999133 adj=49997459 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=54624 bytes_read=1856166 bytes_retransmit=9 bytes_invalid=0 send_seq=7452 receive_seq=7452 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997936 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15324 bytes_read=116772 bytes_retransmit=9 bytes_invalid=0 send_seq=1753 receive_seq=1753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997819 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6391 bytes_read=229397 bytes_retransmit=9 bytes_invalid=0 send_seq=1016 receive_seq=1016 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997853 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6985 bytes_read=20845 bytes_retransmit=9 bytes_invalid=0 send_seq=1011 receive_seq=1011 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999499 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50061 bytes_read=533848 bytes_retransmit=0 bytes_invalid=0 send_seq=4648 receive_seq=4648 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998813 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=48.8 th1: temp=48.0 th2: temp=49.7 th3: temp=47.6 sysload=0.18 cputime=116.498 memavail=7406512 print_time=941.212 buffer_time=2.248 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 917.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11793963 bytes_read=1370047 bytes_retransmit=9 bytes_invalid=0 send_seq=203862 receive_seq=203862 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=44739 freq=400015480 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6238 bytes_read=21244 bytes_retransmit=0 bytes_invalid=0 send_seq=1011 receive_seq=1011 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999133 adj=49997456 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=54700 bytes_read=1859205 bytes_retransmit=9 bytes_invalid=0 send_seq=7463 receive_seq=7463 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997952 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15330 bytes_read=116865 bytes_retransmit=9 bytes_invalid=0 send_seq=1754 receive_seq=1754 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997800 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6397 bytes_read=229631 bytes_retransmit=9 bytes_invalid=0 send_seq=1017 receive_seq=1017 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999535 adj=47997863 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6991 bytes_read=20861 bytes_retransmit=9 bytes_invalid=0 send_seq=1012 receive_seq=1012 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999498 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50067 bytes_read=534204 bytes_retransmit=0 bytes_invalid=0 send_seq=4649 receive_seq=4649 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998806 coil_temp=17.7 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=48.7 th1: temp=47.8 th2: temp=49.7 th3: temp=47.7 sysload=0.18 cputime=116.650 memavail=7406528 print_time=942.289 buffer_time=2.324 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 918.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11818744 bytes_read=1372397 bytes_retransmit=9 bytes_invalid=0 send_seq=204270 receive_seq=204270 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=46595 freq=400015471 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6244 bytes_read=21260 bytes_retransmit=0 bytes_invalid=0 send_seq=1012 receive_seq=1012 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999134 adj=49997414 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=54776 bytes_read=1862271 bytes_retransmit=9 bytes_invalid=0 send_seq=7474 receive_seq=7474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997881 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15336 bytes_read=116984 bytes_retransmit=9 bytes_invalid=0 send_seq=1755 receive_seq=1755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997751 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6403 bytes_read=229940 bytes_retransmit=9 bytes_invalid=0 send_seq=1018 receive_seq=1018 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997836 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=6997 bytes_read=20877 bytes_retransmit=9 bytes_invalid=0 send_seq=1013 receive_seq=1013 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999488 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50073 bytes_read=534560 bytes_retransmit=0 bytes_invalid=0 send_seq=4650 receive_seq=4650 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998780 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=48.9 th1: temp=47.8 th2: temp=49.8 th3: temp=47.8 sysload=0.18 cputime=116.805 memavail=7406528 print_time=943.365 buffer_time=2.401 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 919.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11843601 bytes_read=1374771 bytes_retransmit=9 bytes_invalid=0 send_seq=204678 receive_seq=204677 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=48414 freq=400015466 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6250 bytes_read=21289 bytes_retransmit=0 bytes_invalid=0 send_seq=1013 receive_seq=1013 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999135 adj=49997389 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=54852 bytes_read=1865312 bytes_retransmit=9 bytes_invalid=0 send_seq=7485 receive_seq=7485 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997852 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15342 bytes_read=117077 bytes_retransmit=9 bytes_invalid=0 send_seq=1756 receive_seq=1756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997713 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6409 bytes_read=230174 bytes_retransmit=9 bytes_invalid=0 send_seq=1019 receive_seq=1019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997808 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7003 bytes_read=20893 bytes_retransmit=9 bytes_invalid=0 send_seq=1014 receive_seq=1014 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999481 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50079 bytes_read=534916 bytes_retransmit=0 bytes_invalid=0 send_seq=4651 receive_seq=4651 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998760 coil_temp=17.7 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=48.7 th1: temp=48.1 th2: temp=50.2 th3: temp=47.7 sysload=0.18 cputime=116.953 memavail=7406528 print_time=944.442 buffer_time=2.476 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 920.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11868440 bytes_read=1377137 bytes_retransmit=9 bytes_invalid=0 send_seq=205086 receive_seq=205085 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=38041 freq=400015455 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6256 bytes_read=21305 bytes_retransmit=0 bytes_invalid=0 send_seq=1014 receive_seq=1014 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999136 adj=49997369 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=54928 bytes_read=1868365 bytes_retransmit=9 bytes_invalid=0 send_seq=7496 receive_seq=7496 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997825 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15348 bytes_read=117191 bytes_retransmit=9 bytes_invalid=0 send_seq=1757 receive_seq=1757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997693 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6415 bytes_read=230408 bytes_retransmit=9 bytes_invalid=0 send_seq=1020 receive_seq=1020 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997790 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7009 bytes_read=20909 bytes_retransmit=9 bytes_invalid=0 send_seq=1015 receive_seq=1015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999475 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50085 bytes_read=535272 bytes_retransmit=0 bytes_invalid=0 send_seq=4652 receive_seq=4652 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998753 coil_temp=17.7 refs=0 mcu_temp=20.91 supply_voltage=3.012 th0: temp=48.2 th1: temp=47.8 th2: temp=49.8 th3: temp=47.7 sysload=0.18 cputime=117.087 memavail=7406312 print_time=944.980 buffer_time=2.014 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 921.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11893125 bytes_read=1379437 bytes_retransmit=9 bytes_invalid=0 send_seq=205483 receive_seq=205483 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=39932 freq=400015444 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6262 bytes_read=21321 bytes_retransmit=0 bytes_invalid=0 send_seq=1015 receive_seq=1015 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999141 adj=49997401 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=54997 bytes_read=1871450 bytes_retransmit=9 bytes_invalid=0 send_seq=7506 receive_seq=7506 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997841 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15354 bytes_read=117319 bytes_retransmit=9 bytes_invalid=0 send_seq=1758 receive_seq=1758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997704 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6421 bytes_read=230702 bytes_retransmit=9 bytes_invalid=0 send_seq=1021 receive_seq=1021 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997799 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7015 bytes_read=20936 bytes_retransmit=9 bytes_invalid=0 send_seq=1016 receive_seq=1016 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999477 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50091 bytes_read=535628 bytes_retransmit=0 bytes_invalid=0 send_seq=4653 receive_seq=4653 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998759 coil_temp=17.7 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=48.6 th1: temp=47.8 th2: temp=49.9 th3: temp=47.7 sysload=0.17 cputime=117.239 memavail=7406336 print_time=946.056 buffer_time=2.090 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 922.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11918886 bytes_read=1381861 bytes_retransmit=9 bytes_invalid=0 send_seq=205901 receive_seq=205901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=40860 freq=400015492 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6268 bytes_read=21337 bytes_retransmit=0 bytes_invalid=0 send_seq=1016 receive_seq=1016 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999142 adj=49997452 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=55073 bytes_read=1874508 bytes_retransmit=9 bytes_invalid=0 send_seq=7517 receive_seq=7517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997848 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15360 bytes_read=117419 bytes_retransmit=9 bytes_invalid=0 send_seq=1759 receive_seq=1759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997703 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6427 bytes_read=230936 bytes_retransmit=9 bytes_invalid=0 send_seq=1022 receive_seq=1022 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997810 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7021 bytes_read=20952 bytes_retransmit=9 bytes_invalid=0 send_seq=1017 receive_seq=1017 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999476 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50097 bytes_read=535984 bytes_retransmit=0 bytes_invalid=0 send_seq=4654 receive_seq=4654 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998759 coil_temp=17.7 refs=0 mcu_temp=20.91 supply_voltage=3.012 th0: temp=48.5 th1: temp=47.9 th2: temp=49.9 th3: temp=47.9 sysload=0.17 cputime=117.390 memavail=7406336 print_time=947.133 buffer_time=2.166 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 923.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11943765 bytes_read=1384206 bytes_retransmit=9 bytes_invalid=0 send_seq=206310 receive_seq=206308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=42681 freq=400015516 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6274 bytes_read=21353 bytes_retransmit=0 bytes_invalid=0 send_seq=1017 receive_seq=1017 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999142 adj=49997330 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=55149 bytes_read=1877566 bytes_retransmit=9 bytes_invalid=0 send_seq=7528 receive_seq=7528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997721 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15366 bytes_read=117519 bytes_retransmit=9 bytes_invalid=0 send_seq=1760 receive_seq=1760 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997570 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6433 bytes_read=231185 bytes_retransmit=9 bytes_invalid=0 send_seq=1023 receive_seq=1023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997707 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7027 bytes_read=20968 bytes_retransmit=9 bytes_invalid=0 send_seq=1018 receive_seq=1018 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50103 bytes_read=536340 bytes_retransmit=0 bytes_invalid=0 send_seq=4655 receive_seq=4655 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998686 coil_temp=17.7 refs=0 mcu_temp=20.91 supply_voltage=3.012 th0: temp=48.9 th1: temp=47.9 th2: temp=49.8 th3: temp=47.9 sysload=0.17 cputime=117.539 memavail=7406084 print_time=948.209 buffer_time=2.242 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 924.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11968554 bytes_read=1386556 bytes_retransmit=9 bytes_invalid=0 send_seq=206716 receive_seq=206716 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=44537 freq=400015517 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6280 bytes_read=21382 bytes_retransmit=0 bytes_invalid=0 send_seq=1018 receive_seq=1018 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999143 adj=49997272 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=55225 bytes_read=1880708 bytes_retransmit=9 bytes_invalid=0 send_seq=7539 receive_seq=7539 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997678 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15372 bytes_read=117647 bytes_retransmit=9 bytes_invalid=0 send_seq=1761 receive_seq=1761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6439 bytes_read=231479 bytes_retransmit=9 bytes_invalid=0 send_seq=1024 receive_seq=1024 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999535 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7033 bytes_read=20984 bytes_retransmit=9 bytes_invalid=0 send_seq=1019 receive_seq=1019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50109 bytes_read=536696 bytes_retransmit=0 bytes_invalid=0 send_seq=4656 receive_seq=4656 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998672 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.6 th1: temp=47.6 th2: temp=49.8 th3: temp=47.9 sysload=0.17 cputime=117.700 memavail=7407204 print_time=949.286 buffer_time=2.317 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 925.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=11993320 bytes_read=1388931 bytes_retransmit=9 bytes_invalid=0 send_seq=207121 receive_seq=207120 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=46393 freq=400015507 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6286 bytes_read=21398 bytes_retransmit=0 bytes_invalid=0 send_seq=1019 receive_seq=1019 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999143 adj=49997265 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=55301 bytes_read=1883766 bytes_retransmit=9 bytes_invalid=0 send_seq=7550 receive_seq=7550 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997671 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15378 bytes_read=117761 bytes_retransmit=9 bytes_invalid=0 send_seq=1762 receive_seq=1762 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997529 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6445 bytes_read=231713 bytes_retransmit=9 bytes_invalid=0 send_seq=1025 receive_seq=1025 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7039 bytes_read=21000 bytes_retransmit=9 bytes_invalid=0 send_seq=1020 receive_seq=1020 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999444 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50115 bytes_read=537052 bytes_retransmit=0 bytes_invalid=0 send_seq=4657 receive_seq=4657 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998666 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.8 th1: temp=47.9 th2: temp=49.8 th3: temp=48.0 sysload=0.17 cputime=117.850 memavail=7405728 print_time=950.362 buffer_time=2.394 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 926.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12018137 bytes_read=1391286 bytes_retransmit=9 bytes_invalid=0 send_seq=207529 receive_seq=207529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=48249 freq=400015494 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6292 bytes_read=21414 bytes_retransmit=0 bytes_invalid=0 send_seq=1020 receive_seq=1020 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999143 adj=49997268 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=55377 bytes_read=1886840 bytes_retransmit=9 bytes_invalid=0 send_seq=7561 receive_seq=7561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997686 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15384 bytes_read=117861 bytes_retransmit=9 bytes_invalid=0 send_seq=1763 receive_seq=1763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997549 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6451 bytes_read=231947 bytes_retransmit=9 bytes_invalid=0 send_seq=1026 receive_seq=1026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997682 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7045 bytes_read=21027 bytes_retransmit=9 bytes_invalid=0 send_seq=1021 receive_seq=1021 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50121 bytes_read=537408 bytes_retransmit=0 bytes_invalid=0 send_seq=4658 receive_seq=4658 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998672 coil_temp=17.7 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=48.6 th1: temp=47.7 th2: temp=49.8 th3: temp=47.9 sysload=0.15 cputime=117.997 memavail=7405728 print_time=951.439 buffer_time=2.469 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 927.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12042868 bytes_read=1393606 bytes_retransmit=9 bytes_invalid=0 send_seq=207931 receive_seq=207931 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=37876 freq=400015497 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6298 bytes_read=21430 bytes_retransmit=0 bytes_invalid=0 send_seq=1021 receive_seq=1021 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999142 adj=49997271 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=55453 bytes_read=1889924 bytes_retransmit=9 bytes_invalid=0 send_seq=7572 receive_seq=7572 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997704 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15390 bytes_read=117989 bytes_retransmit=9 bytes_invalid=0 send_seq=1764 receive_seq=1764 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997565 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6457 bytes_read=232241 bytes_retransmit=9 bytes_invalid=0 send_seq=1027 receive_seq=1027 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997693 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7051 bytes_read=21043 bytes_retransmit=9 bytes_invalid=0 send_seq=1022 receive_seq=1022 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50127 bytes_read=537764 bytes_retransmit=0 bytes_invalid=0 send_seq=4659 receive_seq=4659 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998680 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.7 th1: temp=47.9 th2: temp=49.7 th3: temp=48.1 sysload=0.15 cputime=118.126 memavail=7405728 print_time=951.977 buffer_time=2.007 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 928.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12067667 bytes_read=1395985 bytes_retransmit=9 bytes_invalid=0 send_seq=208339 receive_seq=208339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=39732 freq=400015495 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6304 bytes_read=21446 bytes_retransmit=0 bytes_invalid=0 send_seq=1022 receive_seq=1022 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999143 adj=49997258 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=55529 bytes_read=1892981 bytes_retransmit=9 bytes_invalid=0 send_seq=7583 receive_seq=7583 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997699 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15396 bytes_read=118089 bytes_retransmit=9 bytes_invalid=0 send_seq=1765 receive_seq=1765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6463 bytes_read=232490 bytes_retransmit=9 bytes_invalid=0 send_seq=1028 receive_seq=1028 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7057 bytes_read=21059 bytes_retransmit=9 bytes_invalid=0 send_seq=1023 receive_seq=1023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50133 bytes_read=538120 bytes_retransmit=0 bytes_invalid=0 send_seq=4660 receive_seq=4660 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998675 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=49.2 th1: temp=47.8 th2: temp=49.8 th3: temp=47.9 sysload=0.15 cputime=118.278 memavail=7405728 print_time=953.053 buffer_time=2.082 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 929.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12093507 bytes_read=1398405 bytes_retransmit=9 bytes_invalid=0 send_seq=208761 receive_seq=208761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=40660 freq=400015501 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6310 bytes_read=21475 bytes_retransmit=0 bytes_invalid=0 send_seq=1023 receive_seq=1023 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999144 adj=49997262 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=55605 bytes_read=1896037 bytes_retransmit=9 bytes_invalid=0 send_seq=7594 receive_seq=7594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997698 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15402 bytes_read=118189 bytes_retransmit=9 bytes_invalid=0 send_seq=1766 receive_seq=1766 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997548 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6469 bytes_read=232724 bytes_retransmit=9 bytes_invalid=0 send_seq=1029 receive_seq=1029 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7063 bytes_read=21075 bytes_retransmit=9 bytes_invalid=0 send_seq=1024 receive_seq=1024 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999449 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50139 bytes_read=538476 bytes_retransmit=0 bytes_invalid=0 send_seq=4661 receive_seq=4661 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998675 coil_temp=17.7 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=48.8 th1: temp=48.0 th2: temp=49.7 th3: temp=47.8 sysload=0.15 cputime=118.431 memavail=7405504 print_time=954.130 buffer_time=2.159 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 930.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12118253 bytes_read=1400761 bytes_retransmit=9 bytes_invalid=0 send_seq=209167 receive_seq=209167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=42516 freq=400015498 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6316 bytes_read=21491 bytes_retransmit=0 bytes_invalid=0 send_seq=1024 receive_seq=1024 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999145 adj=49997254 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=55681 bytes_read=1899121 bytes_retransmit=9 bytes_invalid=0 send_seq=7605 receive_seq=7605 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997805 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15408 bytes_read=118331 bytes_retransmit=9 bytes_invalid=0 send_seq=1767 receive_seq=1767 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997530 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6475 bytes_read=233018 bytes_retransmit=9 bytes_invalid=0 send_seq=1030 receive_seq=1030 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7069 bytes_read=21091 bytes_retransmit=9 bytes_invalid=0 send_seq=1025 receive_seq=1025 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999449 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50145 bytes_read=538832 bytes_retransmit=0 bytes_invalid=0 send_seq=4662 receive_seq=4662 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998659 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.6 th1: temp=47.8 th2: temp=49.9 th3: temp=48.0 sysload=0.15 cputime=118.584 memavail=7405504 print_time=955.206 buffer_time=2.235 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 931.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12143052 bytes_read=1403140 bytes_retransmit=9 bytes_invalid=0 send_seq=209575 receive_seq=209575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=44372 freq=400015475 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6322 bytes_read=21507 bytes_retransmit=0 bytes_invalid=0 send_seq=1025 receive_seq=1025 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999146 adj=49997260 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=55757 bytes_read=1902253 bytes_retransmit=9 bytes_invalid=0 send_seq=7616 receive_seq=7616 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997792 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15414 bytes_read=118431 bytes_retransmit=9 bytes_invalid=0 send_seq=1768 receive_seq=1768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997580 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6481 bytes_read=233252 bytes_retransmit=9 bytes_invalid=0 send_seq=1031 receive_seq=1031 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7075 bytes_read=21118 bytes_retransmit=9 bytes_invalid=0 send_seq=1026 receive_seq=1026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50151 bytes_read=539188 bytes_retransmit=0 bytes_invalid=0 send_seq=4663 receive_seq=4663 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998657 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=49.1 th1: temp=47.9 th2: temp=50.0 th3: temp=47.8 sysload=0.38 cputime=118.738 memavail=7405504 print_time=956.283 buffer_time=2.311 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 932.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12167846 bytes_read=1405485 bytes_retransmit=9 bytes_invalid=0 send_seq=209982 receive_seq=209982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=46228 freq=400015469 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6328 bytes_read=21523 bytes_retransmit=0 bytes_invalid=0 send_seq=1026 receive_seq=1026 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999147 adj=49997291 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=55833 bytes_read=1905310 bytes_retransmit=9 bytes_invalid=0 send_seq=7627 receive_seq=7627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997800 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15420 bytes_read=118531 bytes_retransmit=9 bytes_invalid=0 send_seq=1769 receive_seq=1769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997629 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6487 bytes_read=233486 bytes_retransmit=9 bytes_invalid=0 send_seq=1032 receive_seq=1032 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997705 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7081 bytes_read=21134 bytes_retransmit=9 bytes_invalid=0 send_seq=1027 receive_seq=1027 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50157 bytes_read=539544 bytes_retransmit=0 bytes_invalid=0 send_seq=4664 receive_seq=4664 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998675 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.4 th1: temp=47.9 th2: temp=50.0 th3: temp=47.9 sysload=0.38 cputime=118.885 memavail=7405504 print_time=957.359 buffer_time=2.386 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.4 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 933.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12192683 bytes_read=1407825 bytes_retransmit=9 bytes_invalid=0 send_seq=210389 receive_seq=210389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=48084 freq=400015456 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6334 bytes_read=21539 bytes_retransmit=0 bytes_invalid=0 send_seq=1027 receive_seq=1027 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999148 adj=49997292 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=55902 bytes_read=1908373 bytes_retransmit=9 bytes_invalid=0 send_seq=7637 receive_seq=7637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997813 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15426 bytes_read=118659 bytes_retransmit=9 bytes_invalid=0 send_seq=1770 receive_seq=1770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997610 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6493 bytes_read=233795 bytes_retransmit=9 bytes_invalid=0 send_seq=1033 receive_seq=1033 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997707 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7087 bytes_read=21150 bytes_retransmit=9 bytes_invalid=0 send_seq=1028 receive_seq=1028 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50163 bytes_read=539900 bytes_retransmit=0 bytes_invalid=0 send_seq=4665 receive_seq=4665 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998678 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.9 th1: temp=47.9 th2: temp=49.7 th3: temp=48.0 sysload=0.38 cputime=119.031 memavail=7405504 print_time=958.436 buffer_time=2.462 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 934.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12217447 bytes_read=1410189 bytes_retransmit=9 bytes_invalid=0 send_seq=210794 receive_seq=210794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=37711 freq=400015443 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6340 bytes_read=21568 bytes_retransmit=0 bytes_invalid=0 send_seq=1028 receive_seq=1028 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999148 adj=49997306 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=55978 bytes_read=1911429 bytes_retransmit=9 bytes_invalid=0 send_seq=7648 receive_seq=7648 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997807 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15432 bytes_read=118759 bytes_retransmit=9 bytes_invalid=0 send_seq=1771 receive_seq=1771 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997634 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6499 bytes_read=234029 bytes_retransmit=9 bytes_invalid=0 send_seq=1034 receive_seq=1034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997720 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7093 bytes_read=21166 bytes_retransmit=9 bytes_invalid=0 send_seq=1029 receive_seq=1029 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50169 bytes_read=540256 bytes_retransmit=0 bytes_invalid=0 send_seq=4666 receive_seq=4666 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998681 coil_temp=17.7 refs=0 mcu_temp=20.91 supply_voltage=3.012 th0: temp=49.0 th1: temp=47.7 th2: temp=49.9 th3: temp=48.0 sysload=0.38 cputime=119.167 memavail=7405504 print_time=958.974 buffer_time=2.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 935.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12242251 bytes_read=1412560 bytes_retransmit=9 bytes_invalid=0 send_seq=211203 receive_seq=211203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=39567 freq=400015450 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6346 bytes_read=21584 bytes_retransmit=0 bytes_invalid=0 send_seq=1029 receive_seq=1029 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999150 adj=49997333 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=56054 bytes_read=1914486 bytes_retransmit=9 bytes_invalid=0 send_seq=7659 receive_seq=7659 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63998149 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15438 bytes_read=118873 bytes_retransmit=9 bytes_invalid=0 send_seq=1772 receive_seq=1772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997666 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6505 bytes_read=234263 bytes_retransmit=9 bytes_invalid=0 send_seq=1035 receive_seq=1035 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997743 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7099 bytes_read=21182 bytes_retransmit=9 bytes_invalid=0 send_seq=1030 receive_seq=1030 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999462 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50175 bytes_read=540612 bytes_retransmit=0 bytes_invalid=0 send_seq=4667 receive_seq=4667 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998701 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.8 th1: temp=48.0 th2: temp=49.9 th3: temp=48.0 sysload=0.38 cputime=119.317 memavail=7405268 print_time=960.050 buffer_time=2.076 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 936.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12268100 bytes_read=1414975 bytes_retransmit=9 bytes_invalid=0 send_seq=211624 receive_seq=211624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400015438 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6352 bytes_read=21600 bytes_retransmit=0 bytes_invalid=0 send_seq=1030 receive_seq=1030 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999150 adj=49997324 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=56130 bytes_read=1917587 bytes_retransmit=9 bytes_invalid=0 send_seq=7670 receive_seq=7670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63998052 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15444 bytes_read=119001 bytes_retransmit=9 bytes_invalid=0 send_seq=1773 receive_seq=1773 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997655 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6511 bytes_read=234557 bytes_retransmit=9 bytes_invalid=0 send_seq=1036 receive_seq=1036 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997723 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7105 bytes_read=21209 bytes_retransmit=9 bytes_invalid=0 send_seq=1031 receive_seq=1031 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50181 bytes_read=540968 bytes_retransmit=0 bytes_invalid=0 send_seq=4668 receive_seq=4668 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998688 coil_temp=17.7 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=49.0 th1: temp=48.1 th2: temp=50.0 th3: temp=48.1 sysload=0.35 cputime=119.468 memavail=7405268 print_time=961.127 buffer_time=2.152 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 937.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12292815 bytes_read=1417344 bytes_retransmit=9 bytes_invalid=0 send_seq=212030 receive_seq=212030 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=42382 freq=400015446 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6358 bytes_read=21616 bytes_retransmit=0 bytes_invalid=0 send_seq=1031 receive_seq=1031 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999153 adj=49997325 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=56206 bytes_read=1920643 bytes_retransmit=9 bytes_invalid=0 send_seq=7681 receive_seq=7681 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997969 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15450 bytes_read=119101 bytes_retransmit=9 bytes_invalid=0 send_seq=1774 receive_seq=1774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997642 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6517 bytes_read=234791 bytes_retransmit=9 bytes_invalid=0 send_seq=1037 receive_seq=1037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997726 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7111 bytes_read=21225 bytes_retransmit=9 bytes_invalid=0 send_seq=1032 receive_seq=1032 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50187 bytes_read=541324 bytes_retransmit=0 bytes_invalid=0 send_seq=4669 receive_seq=4669 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998696 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=48.7 th1: temp=47.9 th2: temp=49.9 th3: temp=48.0 sysload=0.35 cputime=119.621 memavail=7405268 print_time=962.203 buffer_time=2.228 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 938.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12317636 bytes_read=1419699 bytes_retransmit=9 bytes_invalid=0 send_seq=212439 receive_seq=212439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=44238 freq=400015477 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6364 bytes_read=21632 bytes_retransmit=0 bytes_invalid=0 send_seq=1032 receive_seq=1032 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999153 adj=49997321 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=56282 bytes_read=1923700 bytes_retransmit=9 bytes_invalid=0 send_seq=7692 receive_seq=7692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997871 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15456 bytes_read=119201 bytes_retransmit=9 bytes_invalid=0 send_seq=1775 receive_seq=1775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997637 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6523 bytes_read=235040 bytes_retransmit=9 bytes_invalid=0 send_seq=1038 receive_seq=1038 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997704 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7117 bytes_read=21241 bytes_retransmit=9 bytes_invalid=0 send_seq=1033 receive_seq=1033 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999453 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=26.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50193 bytes_read=541680 bytes_retransmit=0 bytes_invalid=0 send_seq=4670 receive_seq=4670 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998677 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=48.9 th1: temp=47.9 th2: temp=50.1 th3: temp=48.2 sysload=0.35 cputime=119.769 memavail=7405268 print_time=963.280 buffer_time=2.305 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 939.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12342413 bytes_read=1422044 bytes_retransmit=9 bytes_invalid=0 send_seq=212846 receive_seq=212846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=46094 freq=400015502 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6370 bytes_read=21661 bytes_retransmit=0 bytes_invalid=0 send_seq=1033 receive_seq=1033 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999152 adj=49997254 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=56358 bytes_read=1926842 bytes_retransmit=9 bytes_invalid=0 send_seq=7703 receive_seq=7703 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997759 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15462 bytes_read=119329 bytes_retransmit=9 bytes_invalid=0 send_seq=1776 receive_seq=1776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6529 bytes_read=235334 bytes_retransmit=9 bytes_invalid=0 send_seq=1039 receive_seq=1039 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7123 bytes_read=21257 bytes_retransmit=9 bytes_invalid=0 send_seq=1034 receive_seq=1034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50199 bytes_read=542036 bytes_retransmit=0 bytes_invalid=0 send_seq=4671 receive_seq=4671 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998670 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.0 th1: temp=48.1 th2: temp=50.1 th3: temp=48.0 sysload=0.35 cputime=119.922 memavail=7405332 print_time=964.356 buffer_time=2.381 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 940.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12367224 bytes_read=1424434 bytes_retransmit=9 bytes_invalid=0 send_seq=213253 receive_seq=213253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=47950 freq=400015529 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6376 bytes_read=21677 bytes_retransmit=0 bytes_invalid=0 send_seq=1034 receive_seq=1034 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999152 adj=49997205 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=56434 bytes_read=1929899 bytes_retransmit=9 bytes_invalid=0 send_seq=7714 receive_seq=7714 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997681 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15468 bytes_read=119443 bytes_retransmit=9 bytes_invalid=0 send_seq=1777 receive_seq=1777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6535 bytes_read=235568 bytes_retransmit=9 bytes_invalid=0 send_seq=1040 receive_seq=1040 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7129 bytes_read=21273 bytes_retransmit=9 bytes_invalid=0 send_seq=1035 receive_seq=1035 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50205 bytes_read=542392 bytes_retransmit=0 bytes_invalid=0 send_seq=4672 receive_seq=4672 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998655 coil_temp=17.7 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=48.9 th1: temp=48.0 th2: temp=50.0 th3: temp=47.9 sysload=0.35 cputime=120.072 memavail=7405332 print_time=965.433 buffer_time=2.457 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 941.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12392198 bytes_read=1426779 bytes_retransmit=9 bytes_invalid=0 send_seq=213660 receive_seq=213660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=49596 freq=400015528 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6382 bytes_read=21693 bytes_retransmit=0 bytes_invalid=0 send_seq=1035 receive_seq=1035 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999153 adj=49997167 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=56510 bytes_read=1932975 bytes_retransmit=9 bytes_invalid=0 send_seq=7725 receive_seq=7725 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997642 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15474 bytes_read=119543 bytes_retransmit=9 bytes_invalid=0 send_seq=1778 receive_seq=1778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997456 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6541 bytes_read=235817 bytes_retransmit=9 bytes_invalid=0 send_seq=1041 receive_seq=1041 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997611 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7135 bytes_read=21300 bytes_retransmit=9 bytes_invalid=0 send_seq=1036 receive_seq=1036 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50211 bytes_read=542748 bytes_retransmit=0 bytes_invalid=0 send_seq=4673 receive_seq=4673 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998686 coil_temp=17.7 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=48.8 th1: temp=48.0 th2: temp=50.0 th3: temp=48.2 sysload=0.64 cputime=120.230 memavail=7405688 print_time=966.509 buffer_time=2.525 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 942.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12416992 bytes_read=1429124 bytes_retransmit=9 bytes_invalid=0 send_seq=214067 receive_seq=214067 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=39268 freq=400015564 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6388 bytes_read=21709 bytes_retransmit=0 bytes_invalid=0 send_seq=1036 receive_seq=1036 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999154 adj=49997186 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=56586 bytes_read=1936061 bytes_retransmit=9 bytes_invalid=0 send_seq=7736 receive_seq=7736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997640 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15480 bytes_read=119671 bytes_retransmit=9 bytes_invalid=0 send_seq=1779 receive_seq=1779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997489 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6547 bytes_read=236096 bytes_retransmit=9 bytes_invalid=0 send_seq=1042 receive_seq=1042 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997626 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7141 bytes_read=21316 bytes_retransmit=9 bytes_invalid=0 send_seq=1037 receive_seq=1037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50217 bytes_read=543104 bytes_retransmit=0 bytes_invalid=0 send_seq=4674 receive_seq=4674 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998698 coil_temp=17.7 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=48.6 th1: temp=48.0 th2: temp=50.0 th3: temp=48.0 sysload=0.64 cputime=120.365 memavail=7405688 print_time=967.047 buffer_time=2.063 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 943.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12442468 bytes_read=1431541 bytes_retransmit=9 bytes_invalid=0 send_seq=214483 receive_seq=214483 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=40461 freq=400015561 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6394 bytes_read=21725 bytes_retransmit=0 bytes_invalid=0 send_seq=1037 receive_seq=1037 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999155 adj=49997152 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=56662 bytes_read=1939119 bytes_retransmit=9 bytes_invalid=0 send_seq=7747 receive_seq=7747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997553 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15486 bytes_read=119771 bytes_retransmit=9 bytes_invalid=0 send_seq=1780 receive_seq=1780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997416 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6553 bytes_read=236345 bytes_retransmit=9 bytes_invalid=0 send_seq=1043 receive_seq=1043 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999535 adj=47997576 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7147 bytes_read=21332 bytes_retransmit=9 bytes_invalid=0 send_seq=1038 receive_seq=1038 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50223 bytes_read=543460 bytes_retransmit=0 bytes_invalid=0 send_seq=4675 receive_seq=4675 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998658 coil_temp=17.7 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=48.7 th1: temp=48.3 th2: temp=50.3 th3: temp=48.0 sysload=0.64 cputime=120.515 memavail=7405688 print_time=968.124 buffer_time=2.138 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 944.5: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12467573 bytes_read=1433901 bytes_retransmit=9 bytes_invalid=0 send_seq=214894 receive_seq=214894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=42020 freq=400015565 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6400 bytes_read=21754 bytes_retransmit=0 bytes_invalid=0 send_seq=1038 receive_seq=1038 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999156 adj=49997178 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=56738 bytes_read=1942233 bytes_retransmit=9 bytes_invalid=0 send_seq=7758 receive_seq=7758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997565 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15492 bytes_read=119871 bytes_retransmit=9 bytes_invalid=0 send_seq=1781 receive_seq=1781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000034 adj=63997456 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6559 bytes_read=236594 bytes_retransmit=9 bytes_invalid=0 send_seq=1044 receive_seq=1044 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997597 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7153 bytes_read=21348 bytes_retransmit=9 bytes_invalid=0 send_seq=1039 receive_seq=1039 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50229 bytes_read=543816 bytes_retransmit=0 bytes_invalid=0 send_seq=4676 receive_seq=4676 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998651 coil_temp=17.7 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=48.8 th1: temp=48.0 th2: temp=50.2 th3: temp=48.1 sysload=0.64 cputime=120.667 memavail=7405688 print_time=969.200 buffer_time=2.214 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 945.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12492367 bytes_read=1436262 bytes_retransmit=9 bytes_invalid=0 send_seq=215301 receive_seq=215301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=43908 freq=400015564 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6406 bytes_read=21770 bytes_retransmit=0 bytes_invalid=0 send_seq=1039 receive_seq=1039 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999156 adj=49997184 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=56814 bytes_read=1945318 bytes_retransmit=9 bytes_invalid=0 send_seq=7769 receive_seq=7769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997657 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15498 bytes_read=120013 bytes_retransmit=9 bytes_invalid=0 send_seq=1782 receive_seq=1782 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000033 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6565 bytes_read=236873 bytes_retransmit=9 bytes_invalid=0 send_seq=1045 receive_seq=1045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997604 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7159 bytes_read=21364 bytes_retransmit=9 bytes_invalid=0 send_seq=1040 receive_seq=1040 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50235 bytes_read=544172 bytes_retransmit=0 bytes_invalid=0 send_seq=4677 receive_seq=4677 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998643 coil_temp=17.7 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=48.7 th1: temp=48.1 th2: temp=50.0 th3: temp=48.1 sysload=0.64 cputime=120.821 memavail=7405232 print_time=970.277 buffer_time=2.290 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 946.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12517118 bytes_read=1438636 bytes_retransmit=9 bytes_invalid=0 send_seq=215708 receive_seq=215708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=45764 freq=400015556 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6412 bytes_read=21786 bytes_retransmit=0 bytes_invalid=0 send_seq=1040 receive_seq=1040 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999156 adj=49997198 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=56883 bytes_read=1948368 bytes_retransmit=9 bytes_invalid=0 send_seq=7779 receive_seq=7779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997643 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15504 bytes_read=120113 bytes_retransmit=9 bytes_invalid=0 send_seq=1783 receive_seq=1783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6571 bytes_read=237107 bytes_retransmit=9 bytes_invalid=0 send_seq=1046 receive_seq=1046 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7165 bytes_read=21391 bytes_retransmit=9 bytes_invalid=0 send_seq=1041 receive_seq=1041 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50241 bytes_read=544528 bytes_retransmit=0 bytes_invalid=0 send_seq=4678 receive_seq=4678 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998647 coil_temp=17.7 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=48.8 th1: temp=47.9 th2: temp=50.0 th3: temp=48.1 sysload=0.67 cputime=120.974 memavail=7405248 print_time=971.353 buffer_time=2.366 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 947.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12541956 bytes_read=1440966 bytes_retransmit=9 bytes_invalid=0 send_seq=216112 receive_seq=216112 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=47588 freq=400015582 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6418 bytes_read=21802 bytes_retransmit=0 bytes_invalid=0 send_seq=1041 receive_seq=1041 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999157 adj=49997209 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=56959 bytes_read=1951425 bytes_retransmit=9 bytes_invalid=0 send_seq=7790 receive_seq=7790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997654 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15510 bytes_read=120213 bytes_retransmit=9 bytes_invalid=0 send_seq=1784 receive_seq=1784 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6577 bytes_read=237356 bytes_retransmit=9 bytes_invalid=0 send_seq=1047 receive_seq=1047 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7171 bytes_read=21407 bytes_retransmit=9 bytes_invalid=0 send_seq=1042 receive_seq=1042 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50247 bytes_read=544868 bytes_retransmit=0 bytes_invalid=0 send_seq=4679 receive_seq=4679 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998653 coil_temp=17.7 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.0 th1: temp=47.9 th2: temp=50.1 th3: temp=48.1 sysload=0.67 cputime=121.124 memavail=7405248 print_time=972.430 buffer_time=2.442 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 948.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12566704 bytes_read=1443301 bytes_retransmit=9 bytes_invalid=0 send_seq=216517 receive_seq=216517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=49463 freq=400015607 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6424 bytes_read=21818 bytes_retransmit=0 bytes_invalid=0 send_seq=1042 receive_seq=1042 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999158 adj=49997185 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=57035 bytes_read=1954510 bytes_retransmit=9 bytes_invalid=0 send_seq=7801 receive_seq=7801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997603 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15516 bytes_read=120341 bytes_retransmit=9 bytes_invalid=0 send_seq=1785 receive_seq=1785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6583 bytes_read=237650 bytes_retransmit=9 bytes_invalid=0 send_seq=1048 receive_seq=1048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7177 bytes_read=21423 bytes_retransmit=9 bytes_invalid=0 send_seq=1043 receive_seq=1043 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50253 bytes_read=545224 bytes_retransmit=0 bytes_invalid=0 send_seq=4680 receive_seq=4680 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998627 coil_temp=17.7 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.0 th2: temp=50.1 th3: temp=48.2 sysload=0.67 cputime=121.270 memavail=7405248 print_time=973.506 buffer_time=2.518 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 949.5: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12591560 bytes_read=1445680 bytes_retransmit=9 bytes_invalid=0 send_seq=216925 receive_seq=216925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=39069 freq=400015623 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6430 bytes_read=21834 bytes_retransmit=0 bytes_invalid=0 send_seq=1043 receive_seq=1043 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999159 adj=49997167 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=57111 bytes_read=1957567 bytes_retransmit=9 bytes_invalid=0 send_seq=7812 receive_seq=7812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997662 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15522 bytes_read=120441 bytes_retransmit=9 bytes_invalid=0 send_seq=1786 receive_seq=1786 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997497 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6589 bytes_read=237884 bytes_retransmit=9 bytes_invalid=0 send_seq=1049 receive_seq=1049 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7183 bytes_read=21439 bytes_retransmit=9 bytes_invalid=0 send_seq=1044 receive_seq=1044 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50259 bytes_read=545580 bytes_retransmit=0 bytes_invalid=0 send_seq=4681 receive_seq=4681 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998609 coil_temp=17.7 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.1 th2: temp=50.3 th3: temp=48.0 sysload=0.67 cputime=121.406 memavail=7405248 print_time=974.044 buffer_time=2.055 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 950.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12616827 bytes_read=1448066 bytes_retransmit=9 bytes_invalid=0 send_seq=217337 receive_seq=217337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=40461 freq=400015636 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6436 bytes_read=21863 bytes_retransmit=0 bytes_invalid=0 send_seq=1044 receive_seq=1044 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999159 adj=49997152 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=57187 bytes_read=1960682 bytes_retransmit=9 bytes_invalid=0 send_seq=7823 receive_seq=7823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997605 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15528 bytes_read=120555 bytes_retransmit=9 bytes_invalid=0 send_seq=1787 receive_seq=1787 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6595 bytes_read=238133 bytes_retransmit=9 bytes_invalid=0 send_seq=1050 receive_seq=1050 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7189 bytes_read=21455 bytes_retransmit=9 bytes_invalid=0 send_seq=1045 receive_seq=1045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999431 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50265 bytes_read=545936 bytes_retransmit=0 bytes_invalid=0 send_seq=4682 receive_seq=4682 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998594 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=48.8 th1: temp=48.1 th2: temp=50.1 th3: temp=48.2 sysload=0.67 cputime=121.556 memavail=7405248 print_time=975.121 buffer_time=2.130 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 951.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12642141 bytes_read=1450451 bytes_retransmit=9 bytes_invalid=0 send_seq=217752 receive_seq=217752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=41820 freq=400015652 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6442 bytes_read=21879 bytes_retransmit=0 bytes_invalid=0 send_seq=1045 receive_seq=1045 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999159 adj=49997144 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=57263 bytes_read=1963784 bytes_retransmit=9 bytes_invalid=0 send_seq=7834 receive_seq=7834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997562 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15534 bytes_read=120683 bytes_retransmit=9 bytes_invalid=0 send_seq=1788 receive_seq=1788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6601 bytes_read=238412 bytes_retransmit=9 bytes_invalid=0 send_seq=1051 receive_seq=1051 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997605 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7195 bytes_read=21482 bytes_retransmit=9 bytes_invalid=0 send_seq=1046 receive_seq=1046 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50271 bytes_read=546292 bytes_retransmit=0 bytes_invalid=0 send_seq=4683 receive_seq=4683 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998588 coil_temp=17.7 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=49.0 th1: temp=48.2 th2: temp=49.9 th3: temp=48.2 sysload=0.62 cputime=121.701 memavail=7405264 print_time=976.197 buffer_time=2.206 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 952.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12666930 bytes_read=1452820 bytes_retransmit=9 bytes_invalid=0 send_seq=218158 receive_seq=218158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=43676 freq=400015668 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6448 bytes_read=21895 bytes_retransmit=0 bytes_invalid=0 send_seq=1046 receive_seq=1046 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999159 adj=49997134 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=57339 bytes_read=1966840 bytes_retransmit=9 bytes_invalid=0 send_seq=7845 receive_seq=7845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997684 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15540 bytes_read=120783 bytes_retransmit=9 bytes_invalid=0 send_seq=1789 receive_seq=1789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997448 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6607 bytes_read=238646 bytes_retransmit=9 bytes_invalid=0 send_seq=1052 receive_seq=1052 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997590 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7201 bytes_read=21498 bytes_retransmit=9 bytes_invalid=0 send_seq=1047 receive_seq=1047 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999425 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50277 bytes_read=546648 bytes_retransmit=0 bytes_invalid=0 send_seq=4684 receive_seq=4684 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998586 coil_temp=17.7 refs=0 mcu_temp=20.91 supply_voltage=3.012 th0: temp=48.7 th1: temp=48.1 th2: temp=50.3 th3: temp=48.2 sysload=0.62 cputime=121.850 memavail=7405264 print_time=977.274 buffer_time=2.282 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 953.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12691719 bytes_read=1455160 bytes_retransmit=9 bytes_invalid=0 send_seq=218564 receive_seq=218564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=45532 freq=400015651 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6454 bytes_read=21910 bytes_retransmit=0 bytes_invalid=0 send_seq=1047 receive_seq=1047 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999160 adj=49997124 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=57415 bytes_read=1969898 bytes_retransmit=9 bytes_invalid=0 send_seq=7856 receive_seq=7856 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997770 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15546 bytes_read=120883 bytes_retransmit=9 bytes_invalid=0 send_seq=1790 receive_seq=1790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997412 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6613 bytes_read=238925 bytes_retransmit=9 bytes_invalid=0 send_seq=1053 receive_seq=1053 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997581 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7207 bytes_read=21514 bytes_retransmit=9 bytes_invalid=0 send_seq=1048 receive_seq=1048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999423 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50283 bytes_read=547004 bytes_retransmit=0 bytes_invalid=0 send_seq=4685 receive_seq=4685 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998588 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=48.7 th1: temp=48.1 th2: temp=49.9 th3: temp=48.1 sysload=0.62 cputime=122.005 memavail=7405264 print_time=978.350 buffer_time=2.358 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 954.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12716488 bytes_read=1457478 bytes_retransmit=9 bytes_invalid=0 send_seq=218966 receive_seq=218966 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=47388 freq=400015634 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6460 bytes_read=21924 bytes_retransmit=0 bytes_invalid=0 send_seq=1048 receive_seq=1048 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999161 adj=49997171 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=57491 bytes_read=1972982 bytes_retransmit=9 bytes_invalid=0 send_seq=7867 receive_seq=7867 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997853 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15552 bytes_read=121011 bytes_retransmit=9 bytes_invalid=0 send_seq=1791 receive_seq=1791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997447 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6619 bytes_read=239189 bytes_retransmit=9 bytes_invalid=0 send_seq=1054 receive_seq=1054 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7213 bytes_read=21530 bytes_retransmit=9 bytes_invalid=0 send_seq=1049 receive_seq=1049 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50289 bytes_read=547360 bytes_retransmit=0 bytes_invalid=0 send_seq=4686 receive_seq=4686 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998610 coil_temp=17.7 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.3 th2: temp=50.3 th3: temp=48.2 sysload=0.62 cputime=122.160 memavail=7405264 print_time=979.427 buffer_time=2.434 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 955.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12741290 bytes_read=1459850 bytes_retransmit=9 bytes_invalid=0 send_seq=219370 receive_seq=219370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=49231 freq=400015626 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6466 bytes_read=21952 bytes_retransmit=0 bytes_invalid=0 send_seq=1049 receive_seq=1049 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999161 adj=49997215 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=57567 bytes_read=1976038 bytes_retransmit=9 bytes_invalid=0 send_seq=7878 receive_seq=7878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997826 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15558 bytes_read=121125 bytes_retransmit=9 bytes_invalid=0 send_seq=1792 receive_seq=1792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997493 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6625 bytes_read=239423 bytes_retransmit=9 bytes_invalid=0 send_seq=1055 receive_seq=1055 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7219 bytes_read=21546 bytes_retransmit=9 bytes_invalid=0 send_seq=1050 receive_seq=1050 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50295 bytes_read=547716 bytes_retransmit=0 bytes_invalid=0 send_seq=4687 receive_seq=4687 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998640 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=48.9 th1: temp=48.0 th2: temp=49.9 th3: temp=48.1 sysload=0.62 cputime=122.310 memavail=7405028 print_time=980.503 buffer_time=2.510 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 956.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12766069 bytes_read=1462180 bytes_retransmit=9 bytes_invalid=0 send_seq=219774 receive_seq=219774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=38871 freq=400015624 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6472 bytes_read=21967 bytes_retransmit=0 bytes_invalid=0 send_seq=1050 receive_seq=1050 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999162 adj=49997229 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=57643 bytes_read=1979113 bytes_retransmit=9 bytes_invalid=0 send_seq=7889 receive_seq=7889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997797 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15564 bytes_read=121225 bytes_retransmit=9 bytes_invalid=0 send_seq=1793 receive_seq=1793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6631 bytes_read=239687 bytes_retransmit=9 bytes_invalid=0 send_seq=1056 receive_seq=1056 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7225 bytes_read=21573 bytes_retransmit=9 bytes_invalid=0 send_seq=1051 receive_seq=1051 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50301 bytes_read=548072 bytes_retransmit=0 bytes_invalid=0 send_seq=4688 receive_seq=4688 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998643 coil_temp=17.7 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.3 th2: temp=50.1 th3: temp=48.2 sysload=0.57 cputime=122.450 memavail=7405044 print_time=981.041 buffer_time=2.048 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 957.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12791167 bytes_read=1464540 bytes_retransmit=9 bytes_invalid=0 send_seq=220184 receive_seq=220184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400015651 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6478 bytes_read=21982 bytes_retransmit=0 bytes_invalid=0 send_seq=1051 receive_seq=1051 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999163 adj=49997240 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=57712 bytes_read=1982174 bytes_retransmit=9 bytes_invalid=0 send_seq=7899 receive_seq=7899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997756 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15570 bytes_read=121353 bytes_retransmit=9 bytes_invalid=0 send_seq=1794 receive_seq=1794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997571 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6637 bytes_read=239951 bytes_retransmit=9 bytes_invalid=0 send_seq=1057 receive_seq=1057 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7231 bytes_read=21589 bytes_retransmit=9 bytes_invalid=0 send_seq=1052 receive_seq=1052 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999444 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50307 bytes_read=548428 bytes_retransmit=0 bytes_invalid=0 send_seq=4689 receive_seq=4689 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998643 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=49.0 th1: temp=48.2 th2: temp=50.2 th3: temp=48.3 sysload=0.57 cputime=122.601 memavail=7405044 print_time=982.118 buffer_time=2.123 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 958.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12816645 bytes_read=1466959 bytes_retransmit=9 bytes_invalid=0 send_seq=220600 receive_seq=220600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=41686 freq=400015640 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6484 bytes_read=21997 bytes_retransmit=0 bytes_invalid=0 send_seq=1052 receive_seq=1052 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999164 adj=49997203 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=57788 bytes_read=1985290 bytes_retransmit=9 bytes_invalid=0 send_seq=7910 receive_seq=7910 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997675 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15576 bytes_read=121453 bytes_retransmit=9 bytes_invalid=0 send_seq=1795 receive_seq=1795 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997529 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6643 bytes_read=240200 bytes_retransmit=9 bytes_invalid=0 send_seq=1058 receive_seq=1058 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7237 bytes_read=21605 bytes_retransmit=9 bytes_invalid=0 send_seq=1053 receive_seq=1053 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50313 bytes_read=548784 bytes_retransmit=0 bytes_invalid=0 send_seq=4690 receive_seq=4690 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998628 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=49.0 th1: temp=48.3 th2: temp=50.0 th3: temp=48.2 sysload=0.57 cputime=122.764 memavail=7399248 print_time=983.194 buffer_time=2.200 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 959.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12841417 bytes_read=1469299 bytes_retransmit=9 bytes_invalid=0 send_seq=221006 receive_seq=221006 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=43542 freq=400015635 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6490 bytes_read=22013 bytes_retransmit=0 bytes_invalid=0 send_seq=1053 receive_seq=1053 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999163 adj=49997233 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=57864 bytes_read=1988349 bytes_retransmit=9 bytes_invalid=0 send_seq=7921 receive_seq=7921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997731 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15582 bytes_read=121553 bytes_retransmit=9 bytes_invalid=0 send_seq=1796 receive_seq=1796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6649 bytes_read=240464 bytes_retransmit=9 bytes_invalid=0 send_seq=1059 receive_seq=1059 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7243 bytes_read=21621 bytes_retransmit=9 bytes_invalid=0 send_seq=1054 receive_seq=1054 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50319 bytes_read=549140 bytes_retransmit=0 bytes_invalid=0 send_seq=4691 receive_seq=4691 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998646 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.0 th1: temp=48.0 th2: temp=50.3 th3: temp=48.1 sysload=0.57 cputime=122.915 memavail=7406688 print_time=984.271 buffer_time=2.276 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 960.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12866211 bytes_read=1471660 bytes_retransmit=9 bytes_invalid=0 send_seq=221413 receive_seq=221413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=45398 freq=400015624 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6496 bytes_read=22042 bytes_retransmit=0 bytes_invalid=0 send_seq=1054 receive_seq=1054 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999164 adj=49997228 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=57940 bytes_read=1991437 bytes_retransmit=9 bytes_invalid=0 send_seq=7932 receive_seq=7932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997697 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15588 bytes_read=121695 bytes_retransmit=9 bytes_invalid=0 send_seq=1797 receive_seq=1797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997565 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6655 bytes_read=240713 bytes_retransmit=9 bytes_invalid=0 send_seq=1060 receive_seq=1060 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997679 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7249 bytes_read=21637 bytes_retransmit=9 bytes_invalid=0 send_seq=1055 receive_seq=1055 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50325 bytes_read=549496 bytes_retransmit=0 bytes_invalid=0 send_seq=4692 receive_seq=4692 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998669 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=48.8 th1: temp=48.1 th2: temp=50.1 th3: temp=48.2 sysload=0.57 cputime=123.064 memavail=7406688 print_time=985.347 buffer_time=2.352 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 961.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12891000 bytes_read=1474029 bytes_retransmit=9 bytes_invalid=0 send_seq=221819 receive_seq=221819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=47254 freq=400015629 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6502 bytes_read=22058 bytes_retransmit=0 bytes_invalid=0 send_seq=1055 receive_seq=1055 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999165 adj=49997247 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=58016 bytes_read=1994513 bytes_retransmit=9 bytes_invalid=0 send_seq=7943 receive_seq=7943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997683 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15594 bytes_read=121795 bytes_retransmit=9 bytes_invalid=0 send_seq=1798 receive_seq=1798 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997556 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6661 bytes_read=240931 bytes_retransmit=9 bytes_invalid=0 send_seq=1061 receive_seq=1061 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7255 bytes_read=21664 bytes_retransmit=9 bytes_invalid=0 send_seq=1056 receive_seq=1056 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999449 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50331 bytes_read=549852 bytes_retransmit=0 bytes_invalid=0 send_seq=4693 receive_seq=4693 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998678 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=49.0 th1: temp=48.1 th2: temp=50.1 th3: temp=48.3 sysload=0.52 cputime=123.212 memavail=7406688 print_time=986.424 buffer_time=2.427 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 962.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12915811 bytes_read=1476369 bytes_retransmit=9 bytes_invalid=0 send_seq=222225 receive_seq=222225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=49067 freq=400015625 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6508 bytes_read=22074 bytes_retransmit=0 bytes_invalid=0 send_seq=1056 receive_seq=1056 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999166 adj=49997249 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=58092 bytes_read=1997569 bytes_retransmit=9 bytes_invalid=0 send_seq=7954 receive_seq=7954 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997646 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15600 bytes_read=121895 bytes_retransmit=9 bytes_invalid=0 send_seq=1799 receive_seq=1799 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6667 bytes_read=241177 bytes_retransmit=9 bytes_invalid=0 send_seq=1062 receive_seq=1062 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7261 bytes_read=21680 bytes_retransmit=9 bytes_invalid=0 send_seq=1057 receive_seq=1057 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50337 bytes_read=550208 bytes_retransmit=0 bytes_invalid=0 send_seq=4694 receive_seq=4694 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998670 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=48.8 th1: temp=48.1 th2: temp=50.1 th3: temp=48.2 sysload=0.52 cputime=123.356 memavail=7406688 print_time=987.500 buffer_time=2.503 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 963.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12940590 bytes_read=1478699 bytes_retransmit=9 bytes_invalid=0 send_seq=222629 receive_seq=222629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=38737 freq=400015610 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6514 bytes_read=22090 bytes_retransmit=0 bytes_invalid=0 send_seq=1057 receive_seq=1057 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999172 adj=49997255 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=58168 bytes_read=2000657 bytes_retransmit=9 bytes_invalid=0 send_seq=7965 receive_seq=7965 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997760 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15606 bytes_read=122023 bytes_retransmit=9 bytes_invalid=0 send_seq=1800 receive_seq=1800 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997507 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6673 bytes_read=241438 bytes_retransmit=9 bytes_invalid=0 send_seq=1063 receive_seq=1063 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7267 bytes_read=21696 bytes_retransmit=9 bytes_invalid=0 send_seq=1058 receive_seq=1058 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50343 bytes_read=550564 bytes_retransmit=0 bytes_invalid=0 send_seq=4695 receive_seq=4695 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998675 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=48.8 th1: temp=48.1 th2: temp=50.3 th3: temp=48.2 sysload=0.52 cputime=123.489 memavail=7406688 print_time=988.039 buffer_time=2.041 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 964.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12965500 bytes_read=1481073 bytes_retransmit=9 bytes_invalid=0 send_seq=223036 receive_seq=223036 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=40461 freq=400015600 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6520 bytes_read=22106 bytes_retransmit=0 bytes_invalid=0 send_seq=1058 receive_seq=1058 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999172 adj=49997340 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=58244 bytes_read=2003720 bytes_retransmit=9 bytes_invalid=0 send_seq=7976 receive_seq=7976 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997752 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15612 bytes_read=122123 bytes_retransmit=9 bytes_invalid=0 send_seq=1801 receive_seq=1801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000033 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6679 bytes_read=241656 bytes_retransmit=9 bytes_invalid=0 send_seq=1064 receive_seq=1064 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997694 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7273 bytes_read=21712 bytes_retransmit=9 bytes_invalid=0 send_seq=1059 receive_seq=1059 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50349 bytes_read=550920 bytes_retransmit=0 bytes_invalid=0 send_seq=4696 receive_seq=4696 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998688 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.3 th2: temp=50.0 th3: temp=48.4 sysload=0.52 cputime=123.635 memavail=7406688 print_time=989.115 buffer_time=2.116 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 965.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=12991171 bytes_read=1483495 bytes_retransmit=9 bytes_invalid=0 send_seq=223456 receive_seq=223456 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=41491 freq=400015591 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=6526 bytes_read=22135 bytes_retransmit=0 bytes_invalid=0 send_seq=1059 receive_seq=1059 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999173 adj=49997348 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=58320 bytes_read=2006836 bytes_retransmit=9 bytes_invalid=0 send_seq=7987 receive_seq=7987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997747 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15618 bytes_read=122237 bytes_retransmit=9 bytes_invalid=0 send_seq=1802 receive_seq=1802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997527 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6685 bytes_read=241904 bytes_retransmit=9 bytes_invalid=0 send_seq=1065 receive_seq=1065 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997709 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7279 bytes_read=21728 bytes_retransmit=9 bytes_invalid=0 send_seq=1060 receive_seq=1060 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50355 bytes_read=551276 bytes_retransmit=0 bytes_invalid=0 send_seq=4697 receive_seq=4697 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998693 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=48.9 th1: temp=48.3 th2: temp=50.2 th3: temp=48.1 sysload=0.52 cputime=123.784 memavail=7408804 print_time=990.191 buffer_time=2.192 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 966.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13015955 bytes_read=1485829 bytes_retransmit=9 bytes_invalid=0 send_seq=223861 receive_seq=223861 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=43347 freq=400015594 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=6532 bytes_read=22151 bytes_retransmit=0 bytes_invalid=0 send_seq=1060 receive_seq=1060 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999174 adj=49997340 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=58396 bytes_read=2009937 bytes_retransmit=9 bytes_invalid=0 send_seq=7998 receive_seq=7998 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997851 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15624 bytes_read=122365 bytes_retransmit=9 bytes_invalid=0 send_seq=1803 receive_seq=1803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000033 adj=63997568 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6691 bytes_read=242168 bytes_retransmit=9 bytes_invalid=0 send_seq=1066 receive_seq=1066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997709 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7285 bytes_read=21755 bytes_retransmit=9 bytes_invalid=0 send_seq=1061 receive_seq=1061 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50361 bytes_read=551632 bytes_retransmit=0 bytes_invalid=0 send_seq=4698 receive_seq=4698 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998694 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=48.8 th1: temp=48.0 th2: temp=50.3 th3: temp=48.1 sysload=0.48 cputime=123.932 memavail=7408804 print_time=991.268 buffer_time=2.267 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 967.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13040834 bytes_read=1488208 bytes_retransmit=9 bytes_invalid=0 send_seq=224270 receive_seq=224269 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=45166 freq=400015592 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=6538 bytes_read=22167 bytes_retransmit=0 bytes_invalid=0 send_seq=1061 receive_seq=1061 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999175 adj=49997330 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=58472 bytes_read=2012995 bytes_retransmit=9 bytes_invalid=0 send_seq=8009 receive_seq=8009 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997771 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15630 bytes_read=122465 bytes_retransmit=9 bytes_invalid=0 send_seq=1804 receive_seq=1804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997535 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6697 bytes_read=242402 bytes_retransmit=9 bytes_invalid=0 send_seq=1067 receive_seq=1067 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997708 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7291 bytes_read=21771 bytes_retransmit=9 bytes_invalid=0 send_seq=1062 receive_seq=1062 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50367 bytes_read=551988 bytes_retransmit=0 bytes_invalid=0 send_seq=4699 receive_seq=4699 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998680 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.0 th1: temp=48.2 th2: temp=50.4 th3: temp=48.3 sysload=0.48 cputime=124.081 memavail=7408804 print_time=992.344 buffer_time=2.343 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 968.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13065566 bytes_read=1490553 bytes_retransmit=9 bytes_invalid=0 send_seq=224676 receive_seq=224676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=47059 freq=400015581 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=6544 bytes_read=22183 bytes_retransmit=0 bytes_invalid=0 send_seq=1062 receive_seq=1062 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999176 adj=49997314 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=58548 bytes_read=2016065 bytes_retransmit=9 bytes_invalid=0 send_seq=8020 receive_seq=8020 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997930 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15636 bytes_read=122565 bytes_retransmit=9 bytes_invalid=0 send_seq=1805 receive_seq=1805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997530 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6703 bytes_read=242681 bytes_retransmit=9 bytes_invalid=0 send_seq=1068 receive_seq=1068 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997697 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7297 bytes_read=21787 bytes_retransmit=9 bytes_invalid=0 send_seq=1063 receive_seq=1063 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999449 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50373 bytes_read=552344 bytes_retransmit=0 bytes_invalid=0 send_seq=4700 receive_seq=4700 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998670 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=49.3 th1: temp=48.3 th2: temp=50.3 th3: temp=48.5 sysload=0.48 cputime=124.226 memavail=7408804 print_time=993.421 buffer_time=2.420 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 969.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13090376 bytes_read=1492898 bytes_retransmit=9 bytes_invalid=0 send_seq=225083 receive_seq=225083 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=48899 freq=400015586 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=6550 bytes_read=22199 bytes_retransmit=0 bytes_invalid=0 send_seq=1063 receive_seq=1063 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999176 adj=49997324 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=58624 bytes_read=2019137 bytes_retransmit=9 bytes_invalid=0 send_seq=8031 receive_seq=8031 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997864 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15642 bytes_read=122693 bytes_retransmit=9 bytes_invalid=0 send_seq=1806 receive_seq=1806 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6709 bytes_read=242945 bytes_retransmit=9 bytes_invalid=0 send_seq=1069 receive_seq=1069 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997701 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7303 bytes_read=21803 bytes_retransmit=9 bytes_invalid=0 send_seq=1064 receive_seq=1064 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50379 bytes_read=552700 bytes_retransmit=0 bytes_invalid=0 send_seq=4701 receive_seq=4701 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998670 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=48.9 th1: temp=48.3 th2: temp=50.2 th3: temp=48.4 sysload=0.48 cputime=124.377 memavail=7408580 print_time=994.497 buffer_time=2.496 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 970.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13115160 bytes_read=1495273 bytes_retransmit=9 bytes_invalid=0 send_seq=225487 receive_seq=225487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=38540 freq=400015718 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6556 bytes_read=22228 bytes_retransmit=0 bytes_invalid=0 send_seq=1064 receive_seq=1064 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999178 adj=49997303 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=58693 bytes_read=2022170 bytes_retransmit=9 bytes_invalid=0 send_seq=8041 receive_seq=8041 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997849 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15648 bytes_read=122793 bytes_retransmit=9 bytes_invalid=0 send_seq=1807 receive_seq=1807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6715 bytes_read=243179 bytes_retransmit=9 bytes_invalid=0 send_seq=1070 receive_seq=1070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997695 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7309 bytes_read=21819 bytes_retransmit=9 bytes_invalid=0 send_seq=1065 receive_seq=1065 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999447 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50385 bytes_read=553056 bytes_retransmit=0 bytes_invalid=0 send_seq=4702 receive_seq=4702 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998659 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.3 th2: temp=50.2 th3: temp=48.2 sysload=0.48 cputime=124.514 memavail=7408580 print_time=995.036 buffer_time=2.033 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 971.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13139944 bytes_read=1497608 bytes_retransmit=9 bytes_invalid=0 send_seq=225892 receive_seq=225892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=40396 freq=400015755 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6562 bytes_read=22244 bytes_retransmit=0 bytes_invalid=0 send_seq=1065 receive_seq=1065 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999184 adj=49997125 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=58769 bytes_read=2025257 bytes_retransmit=9 bytes_invalid=0 send_seq=8052 receive_seq=8052 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997555 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15654 bytes_read=122907 bytes_retransmit=9 bytes_invalid=0 send_seq=1808 receive_seq=1808 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997244 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6721 bytes_read=243443 bytes_retransmit=9 bytes_invalid=0 send_seq=1071 receive_seq=1071 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997511 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7315 bytes_read=21846 bytes_retransmit=9 bytes_invalid=0 send_seq=1066 receive_seq=1066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999914 adj=11999400 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50391 bytes_read=553412 bytes_retransmit=0 bytes_invalid=0 send_seq=4703 receive_seq=4703 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998548 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.1 th1: temp=47.9 th2: temp=50.3 th3: temp=48.3 sysload=0.44 cputime=124.664 memavail=7408580 print_time=996.112 buffer_time=2.110 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 972.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13165730 bytes_read=1500033 bytes_retransmit=9 bytes_invalid=0 send_seq=226315 receive_seq=226315 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=41356 freq=400015739 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6568 bytes_read=22260 bytes_retransmit=0 bytes_invalid=0 send_seq=1066 receive_seq=1066 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999183 adj=49997162 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=58845 bytes_read=2028327 bytes_retransmit=9 bytes_invalid=0 send_seq=8063 receive_seq=8063 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997474 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15660 bytes_read=123035 bytes_retransmit=9 bytes_invalid=0 send_seq=1809 receive_seq=1809 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997183 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=6727 bytes_read=243707 bytes_retransmit=9 bytes_invalid=0 send_seq=1072 receive_seq=1072 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997469 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7321 bytes_read=21862 bytes_retransmit=9 bytes_invalid=0 send_seq=1067 receive_seq=1067 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999393 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50397 bytes_read=553768 bytes_retransmit=0 bytes_invalid=0 send_seq=4704 receive_seq=4704 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998525 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=49.2 th1: temp=48.3 th2: temp=50.2 th3: temp=48.5 sysload=0.44 cputime=124.813 memavail=7408580 print_time=997.189 buffer_time=2.186 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 973.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13190604 bytes_read=1502407 bytes_retransmit=9 bytes_invalid=0 send_seq=226723 receive_seq=226722 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=43145 freq=400015792 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6574 bytes_read=22276 bytes_retransmit=0 bytes_invalid=0 send_seq=1067 receive_seq=1067 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999184 adj=49997182 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=58921 bytes_read=2031444 bytes_retransmit=9 bytes_invalid=0 send_seq=8074 receive_seq=8074 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997601 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15666 bytes_read=123135 bytes_retransmit=9 bytes_invalid=0 send_seq=1810 receive_seq=1810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997291 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6733 bytes_read=243956 bytes_retransmit=9 bytes_invalid=0 send_seq=1073 receive_seq=1073 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997530 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7327 bytes_read=21878 bytes_retransmit=9 bytes_invalid=0 send_seq=1068 receive_seq=1068 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999420 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50403 bytes_read=554124 bytes_retransmit=0 bytes_invalid=0 send_seq=4705 receive_seq=4705 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998570 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.0 th1: temp=48.1 th2: temp=50.4 th3: temp=48.4 sysload=0.44 cputime=124.965 memavail=7408328 print_time=998.265 buffer_time=2.261 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 974.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13215313 bytes_read=1504747 bytes_retransmit=9 bytes_invalid=0 send_seq=227128 receive_seq=227128 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=45036 freq=400015781 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6580 bytes_read=22292 bytes_retransmit=0 bytes_invalid=0 send_seq=1068 receive_seq=1068 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999183 adj=49997120 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=58997 bytes_read=2034514 bytes_retransmit=9 bytes_invalid=0 send_seq=8085 receive_seq=8085 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997538 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15672 bytes_read=123249 bytes_retransmit=9 bytes_invalid=0 send_seq=1811 receive_seq=1811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997231 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6739 bytes_read=244235 bytes_retransmit=9 bytes_invalid=0 send_seq=1074 receive_seq=1074 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997490 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7333 bytes_read=21894 bytes_retransmit=9 bytes_invalid=0 send_seq=1069 receive_seq=1069 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999406 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50409 bytes_read=554480 bytes_retransmit=0 bytes_invalid=0 send_seq=4706 receive_seq=4706 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998532 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.3 th2: temp=49.7 th3: temp=48.3 sysload=0.44 cputime=125.114 memavail=7408332 print_time=999.341 buffer_time=2.337 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 975.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13240165 bytes_read=1507119 bytes_retransmit=9 bytes_invalid=0 send_seq=227535 receive_seq=227535 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=46857 freq=400015774 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6592 bytes_read=22337 bytes_retransmit=0 bytes_invalid=0 send_seq=1070 receive_seq=1070 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999185 adj=49997152 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=59079 bytes_read=2037602 bytes_retransmit=9 bytes_invalid=0 send_seq=8097 receive_seq=8097 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997553 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15684 bytes_read=123379 bytes_retransmit=9 bytes_invalid=0 send_seq=1813 receive_seq=1813 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997293 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6751 bytes_read=244500 bytes_retransmit=9 bytes_invalid=0 send_seq=1076 receive_seq=1076 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997533 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7345 bytes_read=21926 bytes_retransmit=9 bytes_invalid=0 send_seq=1071 receive_seq=1071 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50421 bytes_read=554852 bytes_retransmit=0 bytes_invalid=0 send_seq=4708 receive_seq=4708 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998607 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.4 th2: temp=50.4 th3: temp=48.3 sysload=0.44 cputime=125.275 memavail=7401592 print_time=1000.418 buffer_time=2.412 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 976.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13264894 bytes_read=1509478 bytes_retransmit=9 bytes_invalid=0 send_seq=227940 receive_seq=227940 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=48741 freq=400015767 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6598 bytes_read=22353 bytes_retransmit=0 bytes_invalid=0 send_seq=1071 receive_seq=1071 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999186 adj=49997198 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=59155 bytes_read=2040676 bytes_retransmit=9 bytes_invalid=0 send_seq=8108 receive_seq=8108 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997526 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15690 bytes_read=123493 bytes_retransmit=9 bytes_invalid=0 send_seq=1814 receive_seq=1814 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997402 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6757 bytes_read=244734 bytes_retransmit=9 bytes_invalid=0 send_seq=1077 receive_seq=1077 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997587 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7351 bytes_read=21953 bytes_retransmit=9 bytes_invalid=0 send_seq=1072 receive_seq=1072 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50427 bytes_read=555208 bytes_retransmit=0 bytes_invalid=0 send_seq=4709 receive_seq=4709 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998611 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=48.9 th1: temp=48.3 th2: temp=50.3 th3: temp=48.4 sysload=0.41 cputime=125.423 memavail=7407960 print_time=1001.494 buffer_time=2.489 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 977.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13289708 bytes_read=1511808 bytes_retransmit=9 bytes_invalid=0 send_seq=228344 receive_seq=228344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=38340 freq=400015781 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6604 bytes_read=22369 bytes_retransmit=0 bytes_invalid=0 send_seq=1072 receive_seq=1072 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999184 adj=49997211 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=59231 bytes_read=2043749 bytes_retransmit=9 bytes_invalid=0 send_seq=8119 receive_seq=8119 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997533 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15696 bytes_read=123607 bytes_retransmit=9 bytes_invalid=0 send_seq=1815 receive_seq=1815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997424 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6763 bytes_read=245013 bytes_retransmit=9 bytes_invalid=0 send_seq=1078 receive_seq=1078 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997612 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7357 bytes_read=21969 bytes_retransmit=9 bytes_invalid=0 send_seq=1073 receive_seq=1073 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999436 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50433 bytes_read=555564 bytes_retransmit=0 bytes_invalid=0 send_seq=4710 receive_seq=4710 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998625 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=48.9 th1: temp=48.2 th2: temp=50.4 th3: temp=48.3 sysload=0.41 cputime=125.559 memavail=7407960 print_time=1002.033 buffer_time=2.026 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 978.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13314497 bytes_read=1514148 bytes_retransmit=9 bytes_invalid=0 send_seq=228750 receive_seq=228750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=40196 freq=400015765 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6610 bytes_read=22385 bytes_retransmit=0 bytes_invalid=0 send_seq=1073 receive_seq=1073 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999184 adj=49997177 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=59307 bytes_read=2046820 bytes_retransmit=9 bytes_invalid=0 send_seq=8130 receive_seq=8130 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997481 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15702 bytes_read=123721 bytes_retransmit=9 bytes_invalid=0 send_seq=1816 receive_seq=1816 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997394 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6769 bytes_read=245277 bytes_retransmit=9 bytes_invalid=0 send_seq=1079 receive_seq=1079 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997588 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7363 bytes_read=21985 bytes_retransmit=9 bytes_invalid=0 send_seq=1074 receive_seq=1074 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50439 bytes_read=555920 bytes_retransmit=0 bytes_invalid=0 send_seq=4711 receive_seq=4711 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998606 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.2 th2: temp=50.1 th3: temp=48.5 sysload=0.41 cputime=125.712 memavail=7407960 print_time=1003.109 buffer_time=2.102 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 979.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13340299 bytes_read=1516602 bytes_retransmit=9 bytes_invalid=0 send_seq=229173 receive_seq=229173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=41124 freq=400015776 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6616 bytes_read=22401 bytes_retransmit=0 bytes_invalid=0 send_seq=1074 receive_seq=1074 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999185 adj=49997208 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=59383 bytes_read=2049877 bytes_retransmit=9 bytes_invalid=0 send_seq=8141 receive_seq=8141 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997493 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15708 bytes_read=123821 bytes_retransmit=9 bytes_invalid=0 send_seq=1817 receive_seq=1817 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997425 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6775 bytes_read=245511 bytes_retransmit=9 bytes_invalid=0 send_seq=1080 receive_seq=1080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997614 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7369 bytes_read=22001 bytes_retransmit=9 bytes_invalid=0 send_seq=1075 receive_seq=1075 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50445 bytes_read=556276 bytes_retransmit=0 bytes_invalid=0 send_seq=4712 receive_seq=4712 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998628 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.3 th2: temp=50.1 th3: temp=48.3 sysload=0.41 cputime=125.863 memavail=7407960 print_time=1004.186 buffer_time=2.178 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 980.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13365136 bytes_read=1518963 bytes_retransmit=9 bytes_invalid=0 send_seq=229580 receive_seq=229580 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=42980 freq=400015750 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6622 bytes_read=22430 bytes_retransmit=0 bytes_invalid=0 send_seq=1075 receive_seq=1075 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999187 adj=49997195 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=59459 bytes_read=2053008 bytes_retransmit=9 bytes_invalid=0 send_seq=8152 receive_seq=8152 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997490 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15714 bytes_read=123935 bytes_retransmit=9 bytes_invalid=0 send_seq=1818 receive_seq=1818 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997489 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6781 bytes_read=245790 bytes_retransmit=9 bytes_invalid=0 send_seq=1081 receive_seq=1081 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997621 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7375 bytes_read=22017 bytes_retransmit=9 bytes_invalid=0 send_seq=1076 receive_seq=1076 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50451 bytes_read=556632 bytes_retransmit=0 bytes_invalid=0 send_seq=4713 receive_seq=4713 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998614 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=48.9 th1: temp=48.5 th2: temp=50.3 th3: temp=48.4 sysload=0.41 cputime=126.013 memavail=7407960 print_time=1005.262 buffer_time=2.254 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 981.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13389872 bytes_read=1521293 bytes_retransmit=9 bytes_invalid=0 send_seq=229984 receive_seq=229984 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=44836 freq=400015730 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6628 bytes_read=22446 bytes_retransmit=0 bytes_invalid=0 send_seq=1076 receive_seq=1076 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999187 adj=49997261 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=59528 bytes_read=2056104 bytes_retransmit=9 bytes_invalid=0 send_seq=8162 receive_seq=8162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997542 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15720 bytes_read=124063 bytes_retransmit=9 bytes_invalid=0 send_seq=1819 receive_seq=1819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6787 bytes_read=246039 bytes_retransmit=9 bytes_invalid=0 send_seq=1082 receive_seq=1082 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7381 bytes_read=22044 bytes_retransmit=9 bytes_invalid=0 send_seq=1077 receive_seq=1077 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50457 bytes_read=556988 bytes_retransmit=0 bytes_invalid=0 send_seq=4714 receive_seq=4714 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998645 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.2 th1: temp=48.2 th2: temp=50.3 th3: temp=48.3 sysload=0.45 cputime=126.158 memavail=7407960 print_time=1006.338 buffer_time=2.330 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 982.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13414699 bytes_read=1523657 bytes_retransmit=9 bytes_invalid=0 send_seq=230389 receive_seq=230389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=46692 freq=400015727 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6634 bytes_read=22462 bytes_retransmit=0 bytes_invalid=0 send_seq=1077 receive_seq=1077 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999188 adj=49997281 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=59604 bytes_read=2059218 bytes_retransmit=9 bytes_invalid=0 send_seq=8173 receive_seq=8173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997583 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15726 bytes_read=124163 bytes_retransmit=9 bytes_invalid=0 send_seq=1820 receive_seq=1820 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997541 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6793 bytes_read=246273 bytes_retransmit=9 bytes_invalid=0 send_seq=1083 receive_seq=1083 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7387 bytes_read=22060 bytes_retransmit=9 bytes_invalid=0 send_seq=1078 receive_seq=1078 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50463 bytes_read=557344 bytes_retransmit=0 bytes_invalid=0 send_seq=4715 receive_seq=4715 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998660 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.3 th2: temp=50.3 th3: temp=48.4 sysload=0.45 cputime=126.306 memavail=7407960 print_time=1007.415 buffer_time=2.406 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 983.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13439468 bytes_read=1525977 bytes_retransmit=9 bytes_invalid=0 send_seq=230791 receive_seq=230791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=48548 freq=400015746 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6640 bytes_read=22478 bytes_retransmit=0 bytes_invalid=0 send_seq=1078 receive_seq=1078 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999187 adj=49997284 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=59680 bytes_read=2062330 bytes_retransmit=9 bytes_invalid=0 send_seq=8184 receive_seq=8184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997623 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15732 bytes_read=124268 bytes_retransmit=9 bytes_invalid=0 send_seq=1821 receive_seq=1821 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6799 bytes_read=246567 bytes_retransmit=9 bytes_invalid=0 send_seq=1084 receive_seq=1084 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997682 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7393 bytes_read=22076 bytes_retransmit=9 bytes_invalid=0 send_seq=1079 receive_seq=1079 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50469 bytes_read=557700 bytes_retransmit=0 bytes_invalid=0 send_seq=4716 receive_seq=4716 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998653 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.2 th1: temp=48.2 th2: temp=50.3 th3: temp=48.5 sysload=0.45 cputime=126.455 memavail=7407960 print_time=1008.491 buffer_time=2.482 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 984.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13464217 bytes_read=1528297 bytes_retransmit=9 bytes_invalid=0 send_seq=231193 receive_seq=231193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=38175 freq=400015803 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6646 bytes_read=22494 bytes_retransmit=0 bytes_invalid=0 send_seq=1079 receive_seq=1079 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999186 adj=49997236 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=59756 bytes_read=2065440 bytes_retransmit=9 bytes_invalid=0 send_seq=8195 receive_seq=8195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997589 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15738 bytes_read=124374 bytes_retransmit=9 bytes_invalid=0 send_seq=1822 receive_seq=1822 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000033 adj=63997487 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6805 bytes_read=246816 bytes_retransmit=9 bytes_invalid=0 send_seq=1085 receive_seq=1085 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7399 bytes_read=22092 bytes_retransmit=9 bytes_invalid=0 send_seq=1080 receive_seq=1080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50475 bytes_read=558056 bytes_retransmit=0 bytes_invalid=0 send_seq=4717 receive_seq=4717 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998635 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.4 th2: temp=50.3 th3: temp=48.4 sysload=0.45 cputime=126.584 memavail=7407960 print_time=1009.030 buffer_time=2.019 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 985.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13489001 bytes_read=1530677 bytes_retransmit=9 bytes_invalid=0 send_seq=231598 receive_seq=231598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=40031 freq=400015834 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6652 bytes_read=22523 bytes_retransmit=0 bytes_invalid=0 send_seq=1080 receive_seq=1080 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999187 adj=49997142 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=59832 bytes_read=2068536 bytes_retransmit=9 bytes_invalid=0 send_seq=8206 receive_seq=8206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997451 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15744 bytes_read=124467 bytes_retransmit=9 bytes_invalid=0 send_seq=1823 receive_seq=1823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997446 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6811 bytes_read=247050 bytes_retransmit=9 bytes_invalid=0 send_seq=1086 receive_seq=1086 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997580 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7405 bytes_read=22108 bytes_retransmit=9 bytes_invalid=0 send_seq=1081 receive_seq=1081 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999423 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50481 bytes_read=558412 bytes_retransmit=0 bytes_invalid=0 send_seq=4718 receive_seq=4718 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998581 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.0 th1: temp=48.4 th2: temp=50.3 th3: temp=48.4 sysload=0.45 cputime=126.735 memavail=7406968 print_time=1010.106 buffer_time=2.095 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 986.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13514766 bytes_read=1533081 bytes_retransmit=9 bytes_invalid=0 send_seq=232017 receive_seq=232017 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=40990 freq=400015982 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6658 bytes_read=22539 bytes_retransmit=0 bytes_invalid=0 send_seq=1081 receive_seq=1081 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999187 adj=49997115 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=59908 bytes_read=2071662 bytes_retransmit=9 bytes_invalid=0 send_seq=8217 receive_seq=8217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997384 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15750 bytes_read=124587 bytes_retransmit=9 bytes_invalid=0 send_seq=1824 receive_seq=1824 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997370 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6817 bytes_read=247329 bytes_retransmit=9 bytes_invalid=0 send_seq=1087 receive_seq=1087 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997535 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7411 bytes_read=22135 bytes_retransmit=9 bytes_invalid=0 send_seq=1082 receive_seq=1082 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999411 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50487 bytes_read=558768 bytes_retransmit=0 bytes_invalid=0 send_seq=4719 receive_seq=4719 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998562 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.0 th1: temp=48.3 th2: temp=50.2 th3: temp=48.4 sysload=0.42 cputime=126.887 memavail=7406968 print_time=1011.183 buffer_time=2.171 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 987.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13539555 bytes_read=1535416 bytes_retransmit=9 bytes_invalid=0 send_seq=232423 receive_seq=232423 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=42846 freq=400015960 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6664 bytes_read=22555 bytes_retransmit=0 bytes_invalid=0 send_seq=1082 receive_seq=1082 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999187 adj=49996913 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=59984 bytes_read=2074846 bytes_retransmit=9 bytes_invalid=0 send_seq=8228 receive_seq=8228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997133 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15756 bytes_read=124700 bytes_retransmit=9 bytes_invalid=0 send_seq=1825 receive_seq=1825 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997167 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6823 bytes_read=247578 bytes_retransmit=9 bytes_invalid=0 send_seq=1088 receive_seq=1088 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997343 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7417 bytes_read=22151 bytes_retransmit=9 bytes_invalid=0 send_seq=1083 receive_seq=1083 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999364 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50493 bytes_read=559124 bytes_retransmit=0 bytes_invalid=0 send_seq=4720 receive_seq=4720 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998439 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.2 th2: temp=50.3 th3: temp=48.5 sysload=0.42 cputime=127.036 memavail=7406968 print_time=1012.259 buffer_time=2.246 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 988.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13564331 bytes_read=1537755 bytes_retransmit=9 bytes_invalid=0 send_seq=232823 receive_seq=232823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=44702 freq=400015950 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6670 bytes_read=22571 bytes_retransmit=0 bytes_invalid=0 send_seq=1083 receive_seq=1083 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999188 adj=49997008 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=60060 bytes_read=2077961 bytes_retransmit=9 bytes_invalid=0 send_seq=8239 receive_seq=8239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997278 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15762 bytes_read=124800 bytes_retransmit=9 bytes_invalid=0 send_seq=1826 receive_seq=1826 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000033 adj=63997265 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6829 bytes_read=247827 bytes_retransmit=9 bytes_invalid=0 send_seq=1089 receive_seq=1089 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997439 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7423 bytes_read=22167 bytes_retransmit=9 bytes_invalid=0 send_seq=1084 receive_seq=1084 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999386 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50499 bytes_read=559480 bytes_retransmit=0 bytes_invalid=0 send_seq=4721 receive_seq=4721 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998499 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.2 th1: temp=48.4 th2: temp=50.4 th3: temp=48.5 sysload=0.42 cputime=127.190 memavail=7406780 print_time=1013.336 buffer_time=2.322 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 989.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13589098 bytes_read=1540090 bytes_retransmit=9 bytes_invalid=0 send_seq=233228 receive_seq=233228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=46527 freq=400015955 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6676 bytes_read=22587 bytes_retransmit=0 bytes_invalid=0 send_seq=1084 receive_seq=1084 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999187 adj=49997069 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=60136 bytes_read=2081089 bytes_retransmit=9 bytes_invalid=0 send_seq=8250 receive_seq=8250 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997361 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15768 bytes_read=124914 bytes_retransmit=9 bytes_invalid=0 send_seq=1827 receive_seq=1827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997314 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6835 bytes_read=248121 bytes_retransmit=9 bytes_invalid=0 send_seq=1090 receive_seq=1090 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997500 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7429 bytes_read=22183 bytes_retransmit=9 bytes_invalid=0 send_seq=1085 receive_seq=1085 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999398 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50505 bytes_read=559836 bytes_retransmit=0 bytes_invalid=0 send_seq=4722 receive_seq=4722 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998531 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.4 th2: temp=50.3 th3: temp=48.6 sysload=0.42 cputime=127.343 memavail=7403252 print_time=1014.412 buffer_time=2.398 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 990.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13613882 bytes_read=1542441 bytes_retransmit=9 bytes_invalid=0 send_seq=233633 receive_seq=233633 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=48383 freq=400015934 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6682 bytes_read=22616 bytes_retransmit=0 bytes_invalid=0 send_seq=1085 receive_seq=1085 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999188 adj=49997087 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=60212 bytes_read=2084216 bytes_retransmit=9 bytes_invalid=0 send_seq=8261 receive_seq=8261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997467 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15774 bytes_read=125028 bytes_retransmit=9 bytes_invalid=0 send_seq=1828 receive_seq=1828 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997321 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6841 bytes_read=248355 bytes_retransmit=9 bytes_invalid=0 send_seq=1091 receive_seq=1091 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997516 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7435 bytes_read=22199 bytes_retransmit=9 bytes_invalid=0 send_seq=1086 receive_seq=1086 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999403 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50511 bytes_read=560192 bytes_retransmit=0 bytes_invalid=0 send_seq=4723 receive_seq=4723 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998544 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.3 th2: temp=50.5 th3: temp=48.4 sysload=0.42 cputime=127.505 memavail=7407048 print_time=1015.488 buffer_time=2.474 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 991.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13638711 bytes_read=1544810 bytes_retransmit=9 bytes_invalid=0 send_seq=234039 receive_seq=234039 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=38011 freq=400015908 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6688 bytes_read=22632 bytes_retransmit=0 bytes_invalid=0 send_seq=1086 receive_seq=1086 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999187 adj=49997142 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=60288 bytes_read=2087349 bytes_retransmit=9 bytes_invalid=0 send_seq=8272 receive_seq=8272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997630 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15780 bytes_read=125142 bytes_retransmit=9 bytes_invalid=0 send_seq=1829 receive_seq=1829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000034 adj=63997435 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6847 bytes_read=248589 bytes_retransmit=9 bytes_invalid=0 send_seq=1092 receive_seq=1092 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997561 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7441 bytes_read=22226 bytes_retransmit=9 bytes_invalid=0 send_seq=1087 receive_seq=1087 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999417 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50517 bytes_read=560548 bytes_retransmit=0 bytes_invalid=0 send_seq=4724 receive_seq=4724 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998582 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=49.0 th1: temp=48.3 th2: temp=50.3 th3: temp=48.5 sysload=0.38 cputime=127.642 memavail=7407048 print_time=1016.027 buffer_time=2.012 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 992.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13663572 bytes_read=1547160 bytes_retransmit=9 bytes_invalid=0 send_seq=234448 receive_seq=234447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=39830 freq=400015876 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6694 bytes_read=22648 bytes_retransmit=0 bytes_invalid=0 send_seq=1087 receive_seq=1087 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999188 adj=49997173 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=60364 bytes_read=2090478 bytes_retransmit=9 bytes_invalid=0 send_seq=8283 receive_seq=8283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997654 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15786 bytes_read=125256 bytes_retransmit=9 bytes_invalid=0 send_seq=1830 receive_seq=1830 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997470 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6853 bytes_read=248883 bytes_retransmit=9 bytes_invalid=0 send_seq=1093 receive_seq=1093 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997593 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7447 bytes_read=22242 bytes_retransmit=9 bytes_invalid=0 send_seq=1088 receive_seq=1088 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50523 bytes_read=560904 bytes_retransmit=0 bytes_invalid=0 send_seq=4725 receive_seq=4725 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998622 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=49.2 th1: temp=48.3 th2: temp=50.4 th3: temp=48.4 sysload=0.38 cputime=127.798 memavail=7406040 print_time=1017.103 buffer_time=2.088 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 993.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13689284 bytes_read=1549575 bytes_retransmit=9 bytes_invalid=0 send_seq=234868 receive_seq=234868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40825 freq=400015874 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6700 bytes_read=22664 bytes_retransmit=0 bytes_invalid=0 send_seq=1088 receive_seq=1088 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999188 adj=49997229 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=60433 bytes_read=2093583 bytes_retransmit=9 bytes_invalid=0 send_seq=8293 receive_seq=8293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997686 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15792 bytes_read=125370 bytes_retransmit=9 bytes_invalid=0 send_seq=1831 receive_seq=1831 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6859 bytes_read=249132 bytes_retransmit=9 bytes_invalid=0 send_seq=1094 receive_seq=1094 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7453 bytes_read=22258 bytes_retransmit=9 bytes_invalid=0 send_seq=1089 receive_seq=1089 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50529 bytes_read=561260 bytes_retransmit=0 bytes_invalid=0 send_seq=4726 receive_seq=4726 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998654 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.5 th2: temp=50.4 th3: temp=48.5 sysload=0.38 cputime=127.960 memavail=7406896 print_time=1018.180 buffer_time=2.164 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 994.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13714068 bytes_read=1551939 bytes_retransmit=9 bytes_invalid=0 send_seq=235273 receive_seq=235273 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=42651 freq=400015864 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6706 bytes_read=22680 bytes_retransmit=0 bytes_invalid=0 send_seq=1089 receive_seq=1089 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999189 adj=49997230 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=60509 bytes_read=2096697 bytes_retransmit=9 bytes_invalid=0 send_seq=8304 receive_seq=8304 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997673 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15798 bytes_read=125470 bytes_retransmit=9 bytes_invalid=0 send_seq=1832 receive_seq=1832 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997486 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6865 bytes_read=249366 bytes_retransmit=9 bytes_invalid=0 send_seq=1095 receive_seq=1095 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7459 bytes_read=22274 bytes_retransmit=9 bytes_invalid=0 send_seq=1090 receive_seq=1090 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50535 bytes_read=561616 bytes_retransmit=0 bytes_invalid=0 send_seq=4727 receive_seq=4727 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998645 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=49.3 th1: temp=48.3 th2: temp=50.5 th3: temp=48.4 sysload=0.38 cputime=128.110 memavail=7406896 print_time=1019.256 buffer_time=2.239 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 995.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13738872 bytes_read=1554310 bytes_retransmit=9 bytes_invalid=0 send_seq=235682 receive_seq=235682 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=44507 freq=400015851 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6712 bytes_read=22709 bytes_retransmit=0 bytes_invalid=0 send_seq=1090 receive_seq=1090 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999189 adj=49997247 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=60585 bytes_read=2099885 bytes_retransmit=9 bytes_invalid=0 send_seq=8315 receive_seq=8315 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997723 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15804 bytes_read=125584 bytes_retransmit=9 bytes_invalid=0 send_seq=1833 receive_seq=1833 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997491 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6871 bytes_read=249660 bytes_retransmit=9 bytes_invalid=0 send_seq=1096 receive_seq=1096 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7465 bytes_read=22290 bytes_retransmit=9 bytes_invalid=0 send_seq=1091 receive_seq=1091 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50541 bytes_read=561972 bytes_retransmit=0 bytes_invalid=0 send_seq=4728 receive_seq=4728 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998651 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.2 th1: temp=48.4 th2: temp=50.5 th3: temp=48.3 sysload=0.38 cputime=128.264 memavail=7405896 print_time=1020.333 buffer_time=2.315 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 996.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13763679 bytes_read=1556650 bytes_retransmit=9 bytes_invalid=0 send_seq=236088 receive_seq=236088 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=46363 freq=400015877 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6718 bytes_read=22725 bytes_retransmit=0 bytes_invalid=0 send_seq=1091 receive_seq=1091 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999190 adj=49997257 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=60661 bytes_read=2103031 bytes_retransmit=9 bytes_invalid=0 send_seq=8326 receive_seq=8326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997790 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15810 bytes_read=125712 bytes_retransmit=9 bytes_invalid=0 send_seq=1834 receive_seq=1834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997503 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6877 bytes_read=249894 bytes_retransmit=9 bytes_invalid=0 send_seq=1097 receive_seq=1097 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7471 bytes_read=22317 bytes_retransmit=9 bytes_invalid=0 send_seq=1092 receive_seq=1092 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50547 bytes_read=562328 bytes_retransmit=0 bytes_invalid=0 send_seq=4729 receive_seq=4729 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998657 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.2 th1: temp=48.4 th2: temp=50.6 th3: temp=48.7 sysload=0.51 cputime=128.414 memavail=7405908 print_time=1021.409 buffer_time=2.391 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 997.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13788463 bytes_read=1559010 bytes_retransmit=9 bytes_invalid=0 send_seq=236493 receive_seq=236493 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=48219 freq=400015859 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6724 bytes_read=22741 bytes_retransmit=0 bytes_invalid=0 send_seq=1092 receive_seq=1092 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999190 adj=49997224 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=60737 bytes_read=2106144 bytes_retransmit=9 bytes_invalid=0 send_seq=8337 receive_seq=8337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997808 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15816 bytes_read=125812 bytes_retransmit=9 bytes_invalid=0 send_seq=1835 receive_seq=1835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997445 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6883 bytes_read=250128 bytes_retransmit=9 bytes_invalid=0 send_seq=1098 receive_seq=1098 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7477 bytes_read=22333 bytes_retransmit=9 bytes_invalid=0 send_seq=1093 receive_seq=1093 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50553 bytes_read=562684 bytes_retransmit=0 bytes_invalid=0 send_seq=4730 receive_seq=4730 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998629 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.0 th1: temp=48.5 th2: temp=50.3 th3: temp=48.6 sysload=0.51 cputime=128.560 memavail=7405908 print_time=1022.486 buffer_time=2.468 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 998.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13813247 bytes_read=1561338 bytes_retransmit=9 bytes_invalid=0 send_seq=236897 receive_seq=236897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=37844 freq=400015846 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6730 bytes_read=22757 bytes_retransmit=0 bytes_invalid=0 send_seq=1093 receive_seq=1093 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999190 adj=49997243 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=60813 bytes_read=2109274 bytes_retransmit=9 bytes_invalid=0 send_seq=8348 receive_seq=8348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997856 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15822 bytes_read=125926 bytes_retransmit=9 bytes_invalid=0 send_seq=1836 receive_seq=1836 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6889 bytes_read=250437 bytes_retransmit=9 bytes_invalid=0 send_seq=1099 receive_seq=1099 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7483 bytes_read=22349 bytes_retransmit=9 bytes_invalid=0 send_seq=1094 receive_seq=1094 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50559 bytes_read=563040 bytes_retransmit=0 bytes_invalid=0 send_seq=4731 receive_seq=4731 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998642 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.5 th2: temp=50.4 th3: temp=48.5 sysload=0.51 cputime=128.687 memavail=7405908 print_time=1023.024 buffer_time=2.005 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 999.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13838052 bytes_read=1563673 bytes_retransmit=9 bytes_invalid=0 send_seq=237303 receive_seq=237302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=39700 freq=400015854 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6736 bytes_read=22773 bytes_retransmit=0 bytes_invalid=0 send_seq=1094 receive_seq=1094 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999189 adj=49997264 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=60889 bytes_read=2112403 bytes_retransmit=9 bytes_invalid=0 send_seq=8359 receive_seq=8359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997830 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15828 bytes_read=126040 bytes_retransmit=9 bytes_invalid=0 send_seq=1837 receive_seq=1837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6895 bytes_read=250653 bytes_retransmit=9 bytes_invalid=0 send_seq=1100 receive_seq=1100 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7489 bytes_read=22365 bytes_retransmit=9 bytes_invalid=0 send_seq=1095 receive_seq=1095 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50565 bytes_read=563396 bytes_retransmit=0 bytes_invalid=0 send_seq=4732 receive_seq=4732 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998650 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.4 th1: temp=48.2 th2: temp=50.5 th3: temp=48.5 sysload=0.51 cputime=128.834 memavail=7405908 print_time=1024.100 buffer_time=2.082 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1000.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13863785 bytes_read=1566138 bytes_retransmit=9 bytes_invalid=0 send_seq=237724 receive_seq=237724 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=40660 freq=400015845 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6742 bytes_read=22802 bytes_retransmit=0 bytes_invalid=0 send_seq=1095 receive_seq=1095 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999191 adj=49997231 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=60965 bytes_read=2115516 bytes_retransmit=9 bytes_invalid=0 send_seq=8370 receive_seq=8370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997753 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15834 bytes_read=126140 bytes_retransmit=9 bytes_invalid=0 send_seq=1838 receive_seq=1838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997471 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6901 bytes_read=250887 bytes_retransmit=9 bytes_invalid=0 send_seq=1101 receive_seq=1101 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7495 bytes_read=22381 bytes_retransmit=9 bytes_invalid=0 send_seq=1096 receive_seq=1096 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50571 bytes_read=563752 bytes_retransmit=0 bytes_invalid=0 send_seq=4733 receive_seq=4733 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998686 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.2 th1: temp=48.5 th2: temp=50.5 th3: temp=48.4 sysload=0.51 cputime=128.983 memavail=7405908 print_time=1025.177 buffer_time=2.158 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1001.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13888612 bytes_read=1568473 bytes_retransmit=9 bytes_invalid=0 send_seq=238129 receive_seq=238129 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=42516 freq=400015828 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6748 bytes_read=22818 bytes_retransmit=0 bytes_invalid=0 send_seq=1096 receive_seq=1096 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999191 adj=49997264 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=61041 bytes_read=2118662 bytes_retransmit=9 bytes_invalid=0 send_seq=8381 receive_seq=8381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997714 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15840 bytes_read=126268 bytes_retransmit=9 bytes_invalid=0 send_seq=1839 receive_seq=1839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997475 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6907 bytes_read=251181 bytes_retransmit=9 bytes_invalid=0 send_seq=1102 receive_seq=1102 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7501 bytes_read=22408 bytes_retransmit=9 bytes_invalid=0 send_seq=1097 receive_seq=1097 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50577 bytes_read=564108 bytes_retransmit=0 bytes_invalid=0 send_seq=4734 receive_seq=4734 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998694 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.2 th1: temp=48.5 th2: temp=50.3 th3: temp=48.3 sysload=0.47 cputime=129.131 memavail=7405908 print_time=1026.253 buffer_time=2.234 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1002.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13913368 bytes_read=1570823 bytes_retransmit=9 bytes_invalid=0 send_seq=238537 receive_seq=238537 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=44372 freq=400015811 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6754 bytes_read=22834 bytes_retransmit=0 bytes_invalid=0 send_seq=1097 receive_seq=1097 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999191 adj=49997282 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=61117 bytes_read=2121789 bytes_retransmit=9 bytes_invalid=0 send_seq=8392 receive_seq=8392 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997702 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15846 bytes_read=126382 bytes_retransmit=9 bytes_invalid=0 send_seq=1840 receive_seq=1840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997494 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6913 bytes_read=251415 bytes_retransmit=9 bytes_invalid=0 send_seq=1103 receive_seq=1103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7507 bytes_read=22424 bytes_retransmit=9 bytes_invalid=0 send_seq=1098 receive_seq=1098 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50583 bytes_read=564464 bytes_retransmit=0 bytes_invalid=0 send_seq=4735 receive_seq=4735 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998696 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=49.2 th1: temp=48.2 th2: temp=50.6 th3: temp=48.5 sysload=0.47 cputime=129.279 memavail=7405908 print_time=1027.330 buffer_time=2.310 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1003.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13938205 bytes_read=1573197 bytes_retransmit=9 bytes_invalid=0 send_seq=238944 receive_seq=238944 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=46228 freq=400015955 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6760 bytes_read=22850 bytes_retransmit=0 bytes_invalid=0 send_seq=1098 receive_seq=1098 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999192 adj=49997294 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=61193 bytes_read=2124963 bytes_retransmit=9 bytes_invalid=0 send_seq=8403 receive_seq=8403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997693 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15852 bytes_read=126482 bytes_retransmit=9 bytes_invalid=0 send_seq=1841 receive_seq=1841 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997518 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6919 bytes_read=251664 bytes_retransmit=9 bytes_invalid=0 send_seq=1104 receive_seq=1104 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997695 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7513 bytes_read=22440 bytes_retransmit=9 bytes_invalid=0 send_seq=1099 receive_seq=1099 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999461 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50589 bytes_read=564820 bytes_retransmit=0 bytes_invalid=0 send_seq=4736 receive_seq=4736 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998702 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.4 th2: temp=50.3 th3: temp=48.4 sysload=0.47 cputime=129.427 memavail=7405928 print_time=1028.406 buffer_time=2.386 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1004.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13962941 bytes_read=1575527 bytes_retransmit=9 bytes_invalid=0 send_seq=239348 receive_seq=239348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=48084 freq=400015926 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6766 bytes_read=22866 bytes_retransmit=0 bytes_invalid=0 send_seq=1099 receive_seq=1099 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999191 adj=49997078 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=61269 bytes_read=2128093 bytes_retransmit=9 bytes_invalid=0 send_seq=8414 receive_seq=8414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997403 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15858 bytes_read=126596 bytes_retransmit=9 bytes_invalid=0 send_seq=1842 receive_seq=1842 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997245 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6925 bytes_read=251958 bytes_retransmit=9 bytes_invalid=0 send_seq=1105 receive_seq=1105 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997487 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7519 bytes_read=22456 bytes_retransmit=9 bytes_invalid=0 send_seq=1100 receive_seq=1100 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999408 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50595 bytes_read=565176 bytes_retransmit=0 bytes_invalid=0 send_seq=4737 receive_seq=4737 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998563 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.6 th1: temp=48.6 th2: temp=50.6 th3: temp=48.5 sysload=0.47 cputime=129.576 memavail=7405928 print_time=1029.483 buffer_time=2.462 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1005.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=13987736 bytes_read=1577883 bytes_retransmit=9 bytes_invalid=0 send_seq=239754 receive_seq=239754 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=37711 freq=400015911 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6772 bytes_read=22895 bytes_retransmit=0 bytes_invalid=0 send_seq=1100 receive_seq=1100 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999190 adj=49997134 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=61345 bytes_read=2131220 bytes_retransmit=9 bytes_invalid=0 send_seq=8425 receive_seq=8425 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997672 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15864 bytes_read=126710 bytes_retransmit=9 bytes_invalid=0 send_seq=1843 receive_seq=1843 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997437 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6931 bytes_read=252192 bytes_retransmit=9 bytes_invalid=0 send_seq=1106 receive_seq=1106 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997550 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7525 bytes_read=22472 bytes_retransmit=9 bytes_invalid=0 send_seq=1101 receive_seq=1101 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999423 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50601 bytes_read=565532 bytes_retransmit=0 bytes_invalid=0 send_seq=4738 receive_seq=4738 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998595 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=49.3 th1: temp=48.5 th2: temp=50.4 th3: temp=48.7 sysload=0.47 cputime=129.709 memavail=7405444 print_time=1030.021 buffer_time=1.999 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1006.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14012593 bytes_read=1580262 bytes_retransmit=9 bytes_invalid=0 send_seq=240162 receive_seq=240162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=39533 freq=400015896 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6778 bytes_read=22911 bytes_retransmit=0 bytes_invalid=0 send_seq=1101 receive_seq=1101 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999189 adj=49997150 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=61421 bytes_read=2134352 bytes_retransmit=9 bytes_invalid=0 send_seq=8436 receive_seq=8436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997658 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15870 bytes_read=126824 bytes_retransmit=9 bytes_invalid=0 send_seq=1844 receive_seq=1844 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997469 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6937 bytes_read=252426 bytes_retransmit=9 bytes_invalid=0 send_seq=1107 receive_seq=1107 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997565 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7531 bytes_read=22499 bytes_retransmit=9 bytes_invalid=0 send_seq=1102 receive_seq=1102 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999428 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50607 bytes_read=565888 bytes_retransmit=0 bytes_invalid=0 send_seq=4739 receive_seq=4739 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998606 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.3 th1: temp=48.6 th2: temp=50.3 th3: temp=48.7 sysload=0.43 cputime=129.860 memavail=7405444 print_time=1031.097 buffer_time=2.075 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1007.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14038375 bytes_read=1582667 bytes_retransmit=9 bytes_invalid=0 send_seq=240581 receive_seq=240581 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=40461 freq=400015886 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6784 bytes_read=22927 bytes_retransmit=0 bytes_invalid=0 send_seq=1102 receive_seq=1102 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999189 adj=49997168 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=61497 bytes_read=2137493 bytes_retransmit=9 bytes_invalid=0 send_seq=8447 receive_seq=8447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997695 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15876 bytes_read=126938 bytes_retransmit=9 bytes_invalid=0 send_seq=1845 receive_seq=1845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997487 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=6943 bytes_read=252720 bytes_retransmit=9 bytes_invalid=0 send_seq=1108 receive_seq=1108 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997596 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7537 bytes_read=22515 bytes_retransmit=9 bytes_invalid=0 send_seq=1103 receive_seq=1103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50613 bytes_read=566244 bytes_retransmit=0 bytes_invalid=0 send_seq=4740 receive_seq=4740 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998623 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.0 th1: temp=48.4 th2: temp=50.6 th3: temp=48.6 sysload=0.43 cputime=130.011 memavail=7405444 print_time=1032.174 buffer_time=2.151 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1008.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14063106 bytes_read=1585003 bytes_retransmit=9 bytes_invalid=0 send_seq=240987 receive_seq=240987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=42351 freq=400015851 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6790 bytes_read=22943 bytes_retransmit=0 bytes_invalid=0 send_seq=1103 receive_seq=1103 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999190 adj=49997193 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=61566 bytes_read=2140583 bytes_retransmit=9 bytes_invalid=0 send_seq=8457 receive_seq=8457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997665 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15882 bytes_read=127052 bytes_retransmit=9 bytes_invalid=0 send_seq=1846 receive_seq=1846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6949 bytes_read=252969 bytes_retransmit=9 bytes_invalid=0 send_seq=1109 receive_seq=1109 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7543 bytes_read=22531 bytes_retransmit=9 bytes_invalid=0 send_seq=1104 receive_seq=1104 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50619 bytes_read=566600 bytes_retransmit=0 bytes_invalid=0 send_seq=4741 receive_seq=4741 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998638 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=49.3 th1: temp=48.5 th2: temp=50.4 th3: temp=48.5 sysload=0.43 cputime=130.156 memavail=7405476 print_time=1033.250 buffer_time=2.226 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1009.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14087905 bytes_read=1587382 bytes_retransmit=9 bytes_invalid=0 send_seq=241395 receive_seq=241395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=44207 freq=400015829 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6796 bytes_read=22959 bytes_retransmit=0 bytes_invalid=0 send_seq=1104 receive_seq=1104 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999191 adj=49997258 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=61642 bytes_read=2143696 bytes_retransmit=9 bytes_invalid=0 send_seq=8468 receive_seq=8468 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997699 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15888 bytes_read=127152 bytes_retransmit=9 bytes_invalid=0 send_seq=1847 receive_seq=1847 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997571 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6955 bytes_read=253203 bytes_retransmit=9 bytes_invalid=0 send_seq=1110 receive_seq=1110 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7549 bytes_read=22547 bytes_retransmit=9 bytes_invalid=0 send_seq=1105 receive_seq=1105 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50625 bytes_read=566956 bytes_retransmit=0 bytes_invalid=0 send_seq=4742 receive_seq=4742 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998676 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=48.9 th1: temp=48.5 th2: temp=50.6 th3: temp=48.7 sysload=0.43 cputime=130.309 memavail=7405476 print_time=1034.327 buffer_time=2.303 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1010.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14112768 bytes_read=1589738 bytes_retransmit=9 bytes_invalid=0 send_seq=241801 receive_seq=241801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=45996 freq=400015816 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6802 bytes_read=22988 bytes_retransmit=0 bytes_invalid=0 send_seq=1105 receive_seq=1105 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999191 adj=49997283 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=61718 bytes_read=2146897 bytes_retransmit=9 bytes_invalid=0 send_seq=8479 receive_seq=8479 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997711 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15894 bytes_read=127280 bytes_retransmit=9 bytes_invalid=0 send_seq=1848 receive_seq=1848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997576 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6961 bytes_read=253497 bytes_retransmit=9 bytes_invalid=0 send_seq=1111 receive_seq=1111 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997714 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7555 bytes_read=22563 bytes_retransmit=9 bytes_invalid=0 send_seq=1106 receive_seq=1106 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50631 bytes_read=567312 bytes_retransmit=0 bytes_invalid=0 send_seq=4743 receive_seq=4743 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998717 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.4 th2: temp=50.4 th3: temp=48.7 sysload=0.43 cputime=130.472 memavail=7407096 print_time=1035.403 buffer_time=2.377 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 1011.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14137652 bytes_read=1592073 bytes_retransmit=9 bytes_invalid=0 send_seq=242206 receive_seq=242206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=47785 freq=400015784 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6808 bytes_read=23004 bytes_retransmit=0 bytes_invalid=0 send_seq=1106 receive_seq=1106 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999192 adj=49997290 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=61794 bytes_read=2150027 bytes_retransmit=9 bytes_invalid=0 send_seq=8490 receive_seq=8490 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997701 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15900 bytes_read=127394 bytes_retransmit=9 bytes_invalid=0 send_seq=1849 receive_seq=1849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997562 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6967 bytes_read=253731 bytes_retransmit=9 bytes_invalid=0 send_seq=1112 receive_seq=1112 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997728 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7561 bytes_read=22590 bytes_retransmit=9 bytes_invalid=0 send_seq=1107 receive_seq=1107 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50637 bytes_read=567668 bytes_retransmit=0 bytes_invalid=0 send_seq=4744 receive_seq=4744 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998711 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.2 th1: temp=48.5 th2: temp=50.5 th3: temp=48.6 sysload=0.40 cputime=130.620 memavail=7407096 print_time=1036.480 buffer_time=2.450 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 1012.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14162454 bytes_read=1594432 bytes_retransmit=9 bytes_invalid=0 send_seq=242610 receive_seq=242610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=49596 freq=400015774 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6814 bytes_read=23020 bytes_retransmit=0 bytes_invalid=0 send_seq=1107 receive_seq=1107 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999192 adj=49997324 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=61870 bytes_read=2153140 bytes_retransmit=9 bytes_invalid=0 send_seq=8501 receive_seq=8501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997751 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15906 bytes_read=127494 bytes_retransmit=9 bytes_invalid=0 send_seq=1850 receive_seq=1850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997600 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6973 bytes_read=253965 bytes_retransmit=9 bytes_invalid=0 send_seq=1113 receive_seq=1113 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997753 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7567 bytes_read=22606 bytes_retransmit=9 bytes_invalid=0 send_seq=1108 receive_seq=1108 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999462 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50643 bytes_read=568024 bytes_retransmit=0 bytes_invalid=0 send_seq=4745 receive_seq=4745 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998718 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.4 th1: temp=48.4 th2: temp=50.6 th3: temp=48.8 sysload=0.40 cputime=130.768 memavail=7407096 print_time=1037.556 buffer_time=2.524 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1013.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14187243 bytes_read=1596772 bytes_retransmit=9 bytes_invalid=0 send_seq=243016 receive_seq=243016 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=39236 freq=400015764 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6820 bytes_read=23036 bytes_retransmit=0 bytes_invalid=0 send_seq=1108 receive_seq=1108 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999193 adj=49997321 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=61946 bytes_read=2156281 bytes_retransmit=9 bytes_invalid=0 send_seq=8512 receive_seq=8512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997741 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15912 bytes_read=127622 bytes_retransmit=9 bytes_invalid=0 send_seq=1851 receive_seq=1851 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997588 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6979 bytes_read=254274 bytes_retransmit=9 bytes_invalid=0 send_seq=1114 receive_seq=1114 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997761 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7573 bytes_read=22622 bytes_retransmit=9 bytes_invalid=0 send_seq=1109 receive_seq=1109 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999462 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50649 bytes_read=568380 bytes_retransmit=0 bytes_invalid=0 send_seq=4746 receive_seq=4746 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998715 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=48.9 th1: temp=48.7 th2: temp=50.6 th3: temp=48.7 sysload=0.40 cputime=130.906 memavail=7406872 print_time=1038.094 buffer_time=2.061 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1014.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14212709 bytes_read=1599152 bytes_retransmit=9 bytes_invalid=0 send_seq=243430 receive_seq=243430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=40461 freq=400015747 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6826 bytes_read=23052 bytes_retransmit=0 bytes_invalid=0 send_seq=1109 receive_seq=1109 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999193 adj=49997341 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=62022 bytes_read=2159394 bytes_retransmit=9 bytes_invalid=0 send_seq=8523 receive_seq=8523 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997728 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15918 bytes_read=127722 bytes_retransmit=9 bytes_invalid=0 send_seq=1852 receive_seq=1852 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997592 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6985 bytes_read=254508 bytes_retransmit=9 bytes_invalid=0 send_seq=1115 receive_seq=1115 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997772 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7579 bytes_read=22638 bytes_retransmit=9 bytes_invalid=0 send_seq=1110 receive_seq=1110 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50655 bytes_read=568736 bytes_retransmit=0 bytes_invalid=0 send_seq=4747 receive_seq=4747 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998716 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.5 th1: temp=48.3 th2: temp=50.6 th3: temp=48.7 sysload=0.40 cputime=131.055 memavail=7406872 print_time=1039.171 buffer_time=2.137 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1015.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14237820 bytes_read=1601552 bytes_retransmit=9 bytes_invalid=0 send_seq=243839 receive_seq=243839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=42020 freq=400015772 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6832 bytes_read=23081 bytes_retransmit=0 bytes_invalid=0 send_seq=1110 receive_seq=1110 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999195 adj=49997359 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=62098 bytes_read=2162567 bytes_retransmit=9 bytes_invalid=0 send_seq=8534 receive_seq=8534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997724 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15924 bytes_read=127822 bytes_retransmit=9 bytes_invalid=0 send_seq=1853 receive_seq=1853 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997598 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6991 bytes_read=254742 bytes_retransmit=9 bytes_invalid=0 send_seq=1116 receive_seq=1116 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997800 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7585 bytes_read=22654 bytes_retransmit=9 bytes_invalid=0 send_seq=1111 receive_seq=1111 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999467 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50661 bytes_read=569092 bytes_retransmit=0 bytes_invalid=0 send_seq=4748 receive_seq=4748 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998725 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.7 th1: temp=48.7 th2: temp=50.5 th3: temp=48.6 sysload=0.40 cputime=131.204 memavail=7406628 print_time=1040.247 buffer_time=2.214 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1016.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14262663 bytes_read=1603887 bytes_retransmit=9 bytes_invalid=0 send_seq=244244 receive_seq=244244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=43841 freq=400015883 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6838 bytes_read=23097 bytes_retransmit=0 bytes_invalid=0 send_seq=1111 receive_seq=1111 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999195 adj=49997320 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=62174 bytes_read=2165725 bytes_retransmit=9 bytes_invalid=0 send_seq=8545 receive_seq=8545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997641 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15930 bytes_read=127964 bytes_retransmit=9 bytes_invalid=0 send_seq=1854 receive_seq=1854 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997515 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=6997 bytes_read=255036 bytes_retransmit=9 bytes_invalid=0 send_seq=1117 receive_seq=1117 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997724 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7591 bytes_read=22681 bytes_retransmit=9 bytes_invalid=0 send_seq=1112 receive_seq=1112 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50667 bytes_read=569448 bytes_retransmit=0 bytes_invalid=0 send_seq=4749 receive_seq=4749 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998677 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.3 th1: temp=48.6 th2: temp=50.9 th3: temp=48.7 sysload=0.37 cputime=131.353 memavail=7406628 print_time=1041.324 buffer_time=2.289 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1017.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14287447 bytes_read=1606222 bytes_retransmit=9 bytes_invalid=0 send_seq=244649 receive_seq=244649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=45697 freq=400015871 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6844 bytes_read=23113 bytes_retransmit=0 bytes_invalid=0 send_seq=1112 receive_seq=1112 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999196 adj=49997139 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=62250 bytes_read=2168839 bytes_retransmit=9 bytes_invalid=0 send_seq=8556 receive_seq=8556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997434 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15936 bytes_read=128064 bytes_retransmit=9 bytes_invalid=0 send_seq=1855 receive_seq=1855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997300 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7003 bytes_read=255270 bytes_retransmit=9 bytes_invalid=0 send_seq=1118 receive_seq=1118 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7597 bytes_read=22697 bytes_retransmit=9 bytes_invalid=0 send_seq=1113 receive_seq=1113 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999411 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50673 bytes_read=569804 bytes_retransmit=0 bytes_invalid=0 send_seq=4750 receive_seq=4750 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998574 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=49.3 th1: temp=48.5 th2: temp=50.7 th3: temp=48.7 sysload=0.37 cputime=131.503 memavail=7406628 print_time=1042.400 buffer_time=2.365 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1018.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14312226 bytes_read=1608581 bytes_retransmit=9 bytes_invalid=0 send_seq=245053 receive_seq=245053 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=47553 freq=400015859 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6850 bytes_read=23129 bytes_retransmit=0 bytes_invalid=0 send_seq=1113 receive_seq=1113 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999195 adj=49997176 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=62326 bytes_read=2171952 bytes_retransmit=9 bytes_invalid=0 send_seq=8567 receive_seq=8567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997476 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15942 bytes_read=128164 bytes_retransmit=9 bytes_invalid=0 send_seq=1856 receive_seq=1856 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997460 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7009 bytes_read=255519 bytes_retransmit=9 bytes_invalid=0 send_seq=1119 receive_seq=1119 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7603 bytes_read=22713 bytes_retransmit=9 bytes_invalid=0 send_seq=1114 receive_seq=1114 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999420 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50679 bytes_read=570160 bytes_retransmit=0 bytes_invalid=0 send_seq=4751 receive_seq=4751 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998599 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.4 th1: temp=48.4 th2: temp=50.7 th3: temp=48.8 sysload=0.37 cputime=131.655 memavail=7406628 print_time=1043.477 buffer_time=2.441 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 1019.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14336967 bytes_read=1610907 bytes_retransmit=9 bytes_invalid=0 send_seq=245457 receive_seq=245457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=49396 freq=400015841 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6856 bytes_read=23145 bytes_retransmit=0 bytes_invalid=0 send_seq=1114 receive_seq=1114 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999196 adj=49997194 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=62402 bytes_read=2175095 bytes_retransmit=9 bytes_invalid=0 send_seq=8578 receive_seq=8578 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997521 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15948 bytes_read=128292 bytes_retransmit=9 bytes_invalid=0 send_seq=1857 receive_seq=1857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7015 bytes_read=255813 bytes_retransmit=9 bytes_invalid=0 send_seq=1120 receive_seq=1120 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7609 bytes_read=22729 bytes_retransmit=9 bytes_invalid=0 send_seq=1115 receive_seq=1115 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50685 bytes_read=570516 bytes_retransmit=0 bytes_invalid=0 send_seq=4752 receive_seq=4752 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998616 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.4 th1: temp=48.5 th2: temp=51.0 th3: temp=48.6 sysload=0.37 cputime=131.801 memavail=7406628 print_time=1044.553 buffer_time=2.516 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1020.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14361761 bytes_read=1613268 bytes_retransmit=9 bytes_invalid=0 send_seq=245864 receive_seq=245864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=39036 freq=400015820 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6862 bytes_read=23174 bytes_retransmit=0 bytes_invalid=0 send_seq=1115 receive_seq=1115 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999197 adj=49997234 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=62478 bytes_read=2178208 bytes_retransmit=9 bytes_invalid=0 send_seq=8589 receive_seq=8589 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997559 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=15954 bytes_read=128392 bytes_retransmit=9 bytes_invalid=0 send_seq=1858 receive_seq=1858 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997497 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7021 bytes_read=256047 bytes_retransmit=9 bytes_invalid=0 send_seq=1121 receive_seq=1121 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7615 bytes_read=22745 bytes_retransmit=9 bytes_invalid=0 send_seq=1116 receive_seq=1116 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50691 bytes_read=570872 bytes_retransmit=0 bytes_invalid=0 send_seq=4753 receive_seq=4753 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998671 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.3 th1: temp=48.7 th2: temp=50.7 th3: temp=48.9 sysload=0.37 cputime=131.935 memavail=7406628 print_time=1045.091 buffer_time=2.054 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1021.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14387049 bytes_read=1615672 bytes_retransmit=9 bytes_invalid=0 send_seq=246277 receive_seq=246277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400015805 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6868 bytes_read=23190 bytes_retransmit=0 bytes_invalid=0 send_seq=1116 receive_seq=1116 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999198 adj=49997270 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=62547 bytes_read=2181315 bytes_retransmit=9 bytes_invalid=0 send_seq=8599 receive_seq=8599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997575 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15960 bytes_read=128506 bytes_retransmit=9 bytes_invalid=0 send_seq=1859 receive_seq=1859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7027 bytes_read=256281 bytes_retransmit=9 bytes_invalid=0 send_seq=1122 receive_seq=1122 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7621 bytes_read=22772 bytes_retransmit=9 bytes_invalid=0 send_seq=1117 receive_seq=1117 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50697 bytes_read=571228 bytes_retransmit=0 bytes_invalid=0 send_seq=4754 receive_seq=4754 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998681 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.6 th2: temp=50.9 th3: temp=48.9 sysload=0.34 cputime=132.084 memavail=7406628 print_time=1046.168 buffer_time=2.130 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1022.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14412337 bytes_read=1618047 bytes_retransmit=9 bytes_invalid=0 send_seq=246690 receive_seq=246690 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=41820 freq=400015796 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6874 bytes_read=23206 bytes_retransmit=0 bytes_invalid=0 send_seq=1117 receive_seq=1117 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999198 adj=49997296 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=62623 bytes_read=2184520 bytes_retransmit=9 bytes_invalid=0 send_seq=8610 receive_seq=8610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997592 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15966 bytes_read=128634 bytes_retransmit=9 bytes_invalid=0 send_seq=1860 receive_seq=1860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000033 adj=63997550 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7033 bytes_read=256575 bytes_retransmit=9 bytes_invalid=0 send_seq=1123 receive_seq=1123 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997702 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7627 bytes_read=22788 bytes_retransmit=9 bytes_invalid=0 send_seq=1118 receive_seq=1118 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50703 bytes_read=571584 bytes_retransmit=0 bytes_invalid=0 send_seq=4755 receive_seq=4755 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998682 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=49.3 th1: temp=48.8 th2: temp=50.7 th3: temp=48.6 sysload=0.34 cputime=132.233 memavail=7406628 print_time=1047.244 buffer_time=2.205 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1023.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14437126 bytes_read=1620387 bytes_retransmit=9 bytes_invalid=0 send_seq=247096 receive_seq=247096 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=43676 freq=400015785 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6880 bytes_read=23222 bytes_retransmit=0 bytes_invalid=0 send_seq=1118 receive_seq=1118 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999199 adj=49997297 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=62699 bytes_read=2187633 bytes_retransmit=9 bytes_invalid=0 send_seq=8621 receive_seq=8621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997697 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15972 bytes_read=128734 bytes_retransmit=9 bytes_invalid=0 send_seq=1861 receive_seq=1861 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997638 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7039 bytes_read=256824 bytes_retransmit=9 bytes_invalid=0 send_seq=1124 receive_seq=1124 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997695 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7633 bytes_read=22804 bytes_retransmit=9 bytes_invalid=0 send_seq=1119 receive_seq=1119 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50709 bytes_read=571940 bytes_retransmit=0 bytes_invalid=0 send_seq=4756 receive_seq=4756 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998682 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.4 th1: temp=48.5 th2: temp=50.7 th3: temp=48.7 sysload=0.34 cputime=132.382 memavail=7406628 print_time=1048.321 buffer_time=2.282 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1024.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14461895 bytes_read=1622736 bytes_retransmit=9 bytes_invalid=0 send_seq=247498 receive_seq=247498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=45532 freq=400015758 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6886 bytes_read=23238 bytes_retransmit=0 bytes_invalid=0 send_seq=1119 receive_seq=1119 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999199 adj=49997302 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=62775 bytes_read=2190748 bytes_retransmit=9 bytes_invalid=0 send_seq=8632 receive_seq=8632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997688 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15978 bytes_read=128834 bytes_retransmit=9 bytes_invalid=0 send_seq=1862 receive_seq=1862 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997609 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7045 bytes_read=257058 bytes_retransmit=9 bytes_invalid=0 send_seq=1125 receive_seq=1125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997710 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7639 bytes_read=22820 bytes_retransmit=9 bytes_invalid=0 send_seq=1120 receive_seq=1120 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50715 bytes_read=572280 bytes_retransmit=0 bytes_invalid=0 send_seq=4757 receive_seq=4757 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998689 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.3 th1: temp=48.5 th2: temp=50.6 th3: temp=48.8 sysload=0.34 cputime=132.530 memavail=7406628 print_time=1049.397 buffer_time=2.358 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1025.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14486674 bytes_read=1625082 bytes_retransmit=9 bytes_invalid=0 send_seq=247902 receive_seq=247902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=47388 freq=400015758 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6892 bytes_read=23267 bytes_retransmit=0 bytes_invalid=0 send_seq=1120 receive_seq=1120 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999199 adj=49997327 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=62851 bytes_read=2193897 bytes_retransmit=9 bytes_invalid=0 send_seq=8643 receive_seq=8643 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997712 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15984 bytes_read=128962 bytes_retransmit=9 bytes_invalid=0 send_seq=1863 receive_seq=1863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997623 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7051 bytes_read=257352 bytes_retransmit=9 bytes_invalid=0 send_seq=1126 receive_seq=1126 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997727 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7645 bytes_read=22836 bytes_retransmit=9 bytes_invalid=0 send_seq=1121 receive_seq=1121 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50721 bytes_read=572636 bytes_retransmit=0 bytes_invalid=0 send_seq=4758 receive_seq=4758 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998704 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.4 th1: temp=48.4 th2: temp=50.7 th3: temp=48.8 sysload=0.34 cputime=132.685 memavail=7405684 print_time=1050.474 buffer_time=2.433 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 1026.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14511486 bytes_read=1627422 bytes_retransmit=9 bytes_invalid=0 send_seq=248308 receive_seq=248308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=49231 freq=400015750 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6898 bytes_read=23283 bytes_retransmit=0 bytes_invalid=0 send_seq=1121 receive_seq=1121 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999199 adj=49997314 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=62927 bytes_read=2197031 bytes_retransmit=9 bytes_invalid=0 send_seq=8654 receive_seq=8654 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997691 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15990 bytes_read=129076 bytes_retransmit=9 bytes_invalid=0 send_seq=1864 receive_seq=1864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997602 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7057 bytes_read=257586 bytes_retransmit=9 bytes_invalid=0 send_seq=1127 receive_seq=1127 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997708 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7651 bytes_read=22863 bytes_retransmit=9 bytes_invalid=0 send_seq=1122 receive_seq=1122 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50727 bytes_read=572992 bytes_retransmit=0 bytes_invalid=0 send_seq=4759 receive_seq=4759 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998697 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.5 th1: temp=48.5 th2: temp=51.0 th3: temp=48.8 sysload=0.31 cputime=132.833 memavail=7405684 print_time=1051.550 buffer_time=2.509 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1027.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14536285 bytes_read=1629801 bytes_retransmit=9 bytes_invalid=0 send_seq=248716 receive_seq=248716 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=38871 freq=400015821 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6904 bytes_read=23299 bytes_retransmit=0 bytes_invalid=0 send_seq=1122 receive_seq=1122 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999199 adj=49997308 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=63003 bytes_read=2200145 bytes_retransmit=9 bytes_invalid=0 send_seq=8665 receive_seq=8665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997983 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=15996 bytes_read=129176 bytes_retransmit=9 bytes_invalid=0 send_seq=1865 receive_seq=1865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997582 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7063 bytes_read=257820 bytes_retransmit=9 bytes_invalid=0 send_seq=1128 receive_seq=1128 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997701 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7657 bytes_read=22879 bytes_retransmit=9 bytes_invalid=0 send_seq=1123 receive_seq=1123 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50733 bytes_read=573348 bytes_retransmit=0 bytes_invalid=0 send_seq=4760 receive_seq=4760 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998691 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.3 th1: temp=48.8 th2: temp=51.0 th3: temp=48.8 sysload=0.31 cputime=132.987 memavail=7406908 print_time=1052.088 buffer_time=2.047 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1028.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14561383 bytes_read=1632161 bytes_retransmit=9 bytes_invalid=0 send_seq=249126 receive_seq=249126 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400015822 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6910 bytes_read=23315 bytes_retransmit=0 bytes_invalid=0 send_seq=1123 receive_seq=1123 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999202 adj=49997203 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=63079 bytes_read=2203286 bytes_retransmit=9 bytes_invalid=0 send_seq=8676 receive_seq=8676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997824 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16002 bytes_read=129304 bytes_retransmit=9 bytes_invalid=0 send_seq=1866 receive_seq=1866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997429 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7069 bytes_read=258129 bytes_retransmit=9 bytes_invalid=0 send_seq=1129 receive_seq=1129 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997607 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7663 bytes_read=22895 bytes_retransmit=9 bytes_invalid=0 send_seq=1124 receive_seq=1124 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50739 bytes_read=573704 bytes_retransmit=0 bytes_invalid=0 send_seq=4761 receive_seq=4761 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998621 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=49.5 th1: temp=48.6 th2: temp=50.6 th3: temp=49.0 sysload=0.31 cputime=133.141 memavail=7407056 print_time=1053.165 buffer_time=2.122 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1029.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14586854 bytes_read=1634561 bytes_retransmit=9 bytes_invalid=0 send_seq=249544 receive_seq=249544 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=41686 freq=400015809 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6916 bytes_read=23331 bytes_retransmit=0 bytes_invalid=0 send_seq=1124 receive_seq=1124 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999202 adj=49997232 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=63155 bytes_read=2206400 bytes_retransmit=9 bytes_invalid=0 send_seq=8687 receive_seq=8687 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997764 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16008 bytes_read=129404 bytes_retransmit=9 bytes_invalid=0 send_seq=1867 receive_seq=1867 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997427 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7075 bytes_read=258363 bytes_retransmit=9 bytes_invalid=0 send_seq=1130 receive_seq=1130 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997603 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7669 bytes_read=22911 bytes_retransmit=9 bytes_invalid=0 send_seq=1125 receive_seq=1125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50745 bytes_read=574060 bytes_retransmit=0 bytes_invalid=0 send_seq=4762 receive_seq=4762 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998620 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.3 th1: temp=48.4 th2: temp=50.8 th3: temp=49.0 sysload=0.31 cputime=133.292 memavail=7407056 print_time=1054.241 buffer_time=2.199 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1030.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14611680 bytes_read=1636961 bytes_retransmit=9 bytes_invalid=0 send_seq=249954 receive_seq=249954 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=43511 freq=400015783 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6922 bytes_read=23360 bytes_retransmit=0 bytes_invalid=0 send_seq=1125 receive_seq=1125 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999203 adj=49997253 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=63231 bytes_read=2209574 bytes_retransmit=9 bytes_invalid=0 send_seq=8698 receive_seq=8698 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997732 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16014 bytes_read=129504 bytes_retransmit=9 bytes_invalid=0 send_seq=1868 receive_seq=1868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997450 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7081 bytes_read=258597 bytes_retransmit=9 bytes_invalid=0 send_seq=1131 receive_seq=1131 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997621 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7675 bytes_read=22927 bytes_retransmit=9 bytes_invalid=0 send_seq=1126 receive_seq=1126 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50751 bytes_read=574415 bytes_retransmit=0 bytes_invalid=0 send_seq=4763 receive_seq=4763 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998651 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.5 th1: temp=48.8 th2: temp=50.8 th3: temp=49.0 sysload=0.31 cputime=133.443 memavail=7407056 print_time=1055.318 buffer_time=2.275 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1031.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14636457 bytes_read=1639306 bytes_retransmit=9 bytes_invalid=0 send_seq=250361 receive_seq=250361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=45367 freq=400015764 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6928 bytes_read=23376 bytes_retransmit=0 bytes_invalid=0 send_seq=1126 receive_seq=1126 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999203 adj=49997301 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=63307 bytes_read=2212734 bytes_retransmit=9 bytes_invalid=0 send_seq=8709 receive_seq=8709 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997759 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16020 bytes_read=129646 bytes_retransmit=9 bytes_invalid=0 send_seq=1869 receive_seq=1869 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997502 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7087 bytes_read=258891 bytes_retransmit=9 bytes_invalid=0 send_seq=1132 receive_seq=1132 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7681 bytes_read=22954 bytes_retransmit=9 bytes_invalid=0 send_seq=1127 receive_seq=1127 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50757 bytes_read=574760 bytes_retransmit=0 bytes_invalid=0 send_seq=4764 receive_seq=4764 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998678 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.4 th1: temp=48.6 th2: temp=50.9 th3: temp=48.8 sysload=0.28 cputime=133.597 memavail=7407056 print_time=1056.394 buffer_time=2.351 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1032.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14661246 bytes_read=1641646 bytes_retransmit=9 bytes_invalid=0 send_seq=250767 receive_seq=250767 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=47254 freq=400015750 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6934 bytes_read=23392 bytes_retransmit=0 bytes_invalid=0 send_seq=1127 receive_seq=1127 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999203 adj=49997312 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=63376 bytes_read=2215824 bytes_retransmit=9 bytes_invalid=0 send_seq=8719 receive_seq=8719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997803 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16026 bytes_read=129746 bytes_retransmit=9 bytes_invalid=0 send_seq=1870 receive_seq=1870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7093 bytes_read=259105 bytes_retransmit=9 bytes_invalid=0 send_seq=1133 receive_seq=1133 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997698 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7687 bytes_read=22970 bytes_retransmit=9 bytes_invalid=0 send_seq=1128 receive_seq=1128 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999467 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50763 bytes_read=575105 bytes_retransmit=0 bytes_invalid=0 send_seq=4765 receive_seq=4765 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998685 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.3 th1: temp=48.8 th2: temp=50.6 th3: temp=48.9 sysload=0.28 cputime=133.743 memavail=7407056 print_time=1057.471 buffer_time=2.427 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 1033.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14686062 bytes_read=1644020 bytes_retransmit=9 bytes_invalid=0 send_seq=251174 receive_seq=251174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=49067 freq=400015728 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6940 bytes_read=23408 bytes_retransmit=0 bytes_invalid=0 send_seq=1128 receive_seq=1128 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999204 adj=49997317 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=63452 bytes_read=2218941 bytes_retransmit=9 bytes_invalid=0 send_seq=8730 receive_seq=8730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997770 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16032 bytes_read=129846 bytes_retransmit=9 bytes_invalid=0 send_seq=1871 receive_seq=1871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997597 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7099 bytes_read=259339 bytes_retransmit=9 bytes_invalid=0 send_seq=1134 receive_seq=1134 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997711 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7693 bytes_read=22986 bytes_retransmit=9 bytes_invalid=0 send_seq=1129 receive_seq=1129 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50769 bytes_read=575449 bytes_retransmit=0 bytes_invalid=0 send_seq=4766 receive_seq=4766 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998688 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.2 th1: temp=48.8 th2: temp=50.9 th3: temp=48.7 sysload=0.28 cputime=133.886 memavail=7407064 print_time=1058.547 buffer_time=2.503 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1034.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14710924 bytes_read=1646370 bytes_retransmit=9 bytes_invalid=0 send_seq=251583 receive_seq=251582 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=38670 freq=400015727 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6946 bytes_read=23424 bytes_retransmit=0 bytes_invalid=0 send_seq=1129 receive_seq=1129 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999204 adj=49997340 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=63528 bytes_read=2222085 bytes_retransmit=9 bytes_invalid=0 send_seq=8741 receive_seq=8741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997763 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16038 bytes_read=129974 bytes_retransmit=9 bytes_invalid=0 send_seq=1872 receive_seq=1872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997624 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7105 bytes_read=259648 bytes_retransmit=9 bytes_invalid=0 send_seq=1135 receive_seq=1135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997722 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7699 bytes_read=23002 bytes_retransmit=9 bytes_invalid=0 send_seq=1130 receive_seq=1130 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999467 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50775 bytes_read=575794 bytes_retransmit=0 bytes_invalid=0 send_seq=4767 receive_seq=4767 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998699 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.4 th1: temp=48.7 th2: temp=50.7 th3: temp=48.8 sysload=0.28 cputime=134.022 memavail=7407064 print_time=1059.085 buffer_time=2.040 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1035.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14735776 bytes_read=1648736 bytes_retransmit=9 bytes_invalid=0 send_seq=251990 receive_seq=251990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=40461 freq=400015711 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6952 bytes_read=23453 bytes_retransmit=0 bytes_invalid=0 send_seq=1130 receive_seq=1130 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999205 adj=49997346 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=63604 bytes_read=2225198 bytes_retransmit=9 bytes_invalid=0 send_seq=8752 receive_seq=8752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997733 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16044 bytes_read=130074 bytes_retransmit=9 bytes_invalid=0 send_seq=1873 receive_seq=1873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997629 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7111 bytes_read=259882 bytes_retransmit=9 bytes_invalid=0 send_seq=1136 receive_seq=1136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997715 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7705 bytes_read=23018 bytes_retransmit=9 bytes_invalid=0 send_seq=1131 receive_seq=1131 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50781 bytes_read=576139 bytes_retransmit=0 bytes_invalid=0 send_seq=4768 receive_seq=4768 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998695 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=49.5 th1: temp=48.6 th2: temp=50.7 th3: temp=49.0 sysload=0.28 cputime=134.170 memavail=7406056 print_time=1060.162 buffer_time=2.117 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1036.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14761402 bytes_read=1651130 bytes_retransmit=9 bytes_invalid=0 send_seq=252401 receive_seq=252401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=41521 freq=400015718 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6958 bytes_read=23469 bytes_retransmit=0 bytes_invalid=0 send_seq=1131 receive_seq=1131 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999205 adj=49997360 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=63680 bytes_read=2228329 bytes_retransmit=9 bytes_invalid=0 send_seq=8763 receive_seq=8763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997730 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16050 bytes_read=130188 bytes_retransmit=9 bytes_invalid=0 send_seq=1874 receive_seq=1874 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997634 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7117 bytes_read=260116 bytes_retransmit=9 bytes_invalid=0 send_seq=1137 receive_seq=1137 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997724 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7711 bytes_read=23045 bytes_retransmit=9 bytes_invalid=0 send_seq=1132 receive_seq=1132 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999471 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50787 bytes_read=576484 bytes_retransmit=0 bytes_invalid=0 send_seq=4769 receive_seq=4769 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998730 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=49.2 th1: temp=48.9 th2: temp=50.7 th3: temp=48.9 sysload=0.26 cputime=134.320 memavail=7406056 print_time=1061.238 buffer_time=2.193 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1037.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14786191 bytes_read=1653470 bytes_retransmit=9 bytes_invalid=0 send_seq=252807 receive_seq=252807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=43347 freq=400015828 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6964 bytes_read=23485 bytes_retransmit=0 bytes_invalid=0 send_seq=1132 receive_seq=1132 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999205 adj=49997325 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=63756 bytes_read=2231531 bytes_retransmit=9 bytes_invalid=0 send_seq=8774 receive_seq=8774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997678 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16056 bytes_read=130316 bytes_retransmit=9 bytes_invalid=0 send_seq=1875 receive_seq=1875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997605 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7123 bytes_read=260410 bytes_retransmit=9 bytes_invalid=0 send_seq=1138 receive_seq=1138 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997692 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7717 bytes_read=23061 bytes_retransmit=9 bytes_invalid=0 send_seq=1133 receive_seq=1133 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50793 bytes_read=576829 bytes_retransmit=0 bytes_invalid=0 send_seq=4770 receive_seq=4770 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998703 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.7 th1: temp=48.3 th2: temp=50.6 th3: temp=49.0 sysload=0.26 cputime=134.474 memavail=7406056 print_time=1062.315 buffer_time=2.268 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1038.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14811061 bytes_read=1655840 bytes_retransmit=9 bytes_invalid=0 send_seq=253214 receive_seq=253214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=45166 freq=400015980 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6976 bytes_read=23516 bytes_retransmit=0 bytes_invalid=0 send_seq=1134 receive_seq=1134 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999205 adj=49997142 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=63838 bytes_read=2234660 bytes_retransmit=9 bytes_invalid=0 send_seq=8786 receive_seq=8786 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997467 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16068 bytes_read=130432 bytes_retransmit=9 bytes_invalid=0 send_seq=1877 receive_seq=1877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997380 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7135 bytes_read=260675 bytes_retransmit=9 bytes_invalid=0 send_seq=1140 receive_seq=1140 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997522 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7729 bytes_read=23093 bytes_retransmit=9 bytes_invalid=0 send_seq=1135 receive_seq=1135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999421 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50805 bytes_read=577189 bytes_retransmit=0 bytes_invalid=0 send_seq=4772 receive_seq=4772 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998585 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.2 th1: temp=48.6 th2: temp=50.9 th3: temp=48.9 sysload=0.26 cputime=134.631 memavail=7406056 print_time=1063.391 buffer_time=2.343 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1039.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14835823 bytes_read=1658185 bytes_retransmit=9 bytes_invalid=0 send_seq=253618 receive_seq=253618 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=47022 freq=400016044 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=6982 bytes_read=23531 bytes_retransmit=0 bytes_invalid=0 send_seq=1135 receive_seq=1135 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999206 adj=49996949 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=63914 bytes_read=2237775 bytes_retransmit=9 bytes_invalid=0 send_seq=8797 receive_seq=8797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997283 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16074 bytes_read=130532 bytes_retransmit=9 bytes_invalid=0 send_seq=1878 receive_seq=1878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997105 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7141 bytes_read=260909 bytes_retransmit=9 bytes_invalid=0 send_seq=1141 receive_seq=1141 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997413 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7735 bytes_read=23109 bytes_retransmit=9 bytes_invalid=0 send_seq=1136 receive_seq=1136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999371 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50811 bytes_read=577542 bytes_retransmit=0 bytes_invalid=0 send_seq=4773 receive_seq=4773 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998461 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.5 th1: temp=48.7 th2: temp=50.5 th3: temp=48.9 sysload=0.26 cputime=134.782 memavail=7406076 print_time=1064.468 buffer_time=2.419 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 1040.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14860588 bytes_read=1660536 bytes_retransmit=9 bytes_invalid=0 send_seq=254024 receive_seq=254024 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=48899 freq=400016103 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6988 bytes_read=23559 bytes_retransmit=0 bytes_invalid=0 send_seq=1136 receive_seq=1136 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999207 adj=49996920 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=63990 bytes_read=2240918 bytes_retransmit=9 bytes_invalid=0 send_seq=8808 receive_seq=8808 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997218 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16080 bytes_read=130660 bytes_retransmit=9 bytes_invalid=0 send_seq=1879 receive_seq=1879 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997054 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7147 bytes_read=261203 bytes_retransmit=9 bytes_invalid=0 send_seq=1142 receive_seq=1142 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997378 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7741 bytes_read=23125 bytes_retransmit=9 bytes_invalid=0 send_seq=1137 receive_seq=1137 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999363 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50817 bytes_read=577898 bytes_retransmit=0 bytes_invalid=0 send_seq=4774 receive_seq=4774 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998437 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.0 th1: temp=48.8 th2: temp=50.8 th3: temp=48.9 sysload=0.26 cputime=134.930 memavail=7406112 print_time=1065.544 buffer_time=2.495 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1041.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14885428 bytes_read=1662888 bytes_retransmit=9 bytes_invalid=0 send_seq=254431 receive_seq=254430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=38505 freq=400016077 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=6994 bytes_read=23574 bytes_retransmit=0 bytes_invalid=0 send_seq=1137 receive_seq=1137 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999207 adj=49996911 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=64066 bytes_read=2244048 bytes_retransmit=9 bytes_invalid=0 send_seq=8819 receive_seq=8819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997184 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16086 bytes_read=130760 bytes_retransmit=9 bytes_invalid=0 send_seq=1880 receive_seq=1880 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997017 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7153 bytes_read=261437 bytes_retransmit=9 bytes_invalid=0 send_seq=1143 receive_seq=1143 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997347 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7747 bytes_read=23152 bytes_retransmit=9 bytes_invalid=0 send_seq=1138 receive_seq=1138 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999360 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50823 bytes_read=578254 bytes_retransmit=0 bytes_invalid=0 send_seq=4775 receive_seq=4775 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998424 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.6 th1: temp=48.7 th2: temp=50.8 th3: temp=48.9 sysload=0.24 cputime=135.064 memavail=7405864 print_time=1066.082 buffer_time=2.033 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1042.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14910215 bytes_read=1665223 bytes_retransmit=9 bytes_invalid=0 send_seq=254833 receive_seq=254832 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=40361 freq=400016053 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7000 bytes_read=23589 bytes_retransmit=0 bytes_invalid=0 send_seq=1138 receive_seq=1138 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999207 adj=49996951 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=64142 bytes_read=2247162 bytes_retransmit=9 bytes_invalid=0 send_seq=8830 receive_seq=8830 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997206 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16092 bytes_read=130874 bytes_retransmit=9 bytes_invalid=0 send_seq=1881 receive_seq=1881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997055 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7159 bytes_read=261671 bytes_retransmit=9 bytes_invalid=0 send_seq=1144 receive_seq=1144 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997372 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7753 bytes_read=23168 bytes_retransmit=9 bytes_invalid=0 send_seq=1139 receive_seq=1139 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999368 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50829 bytes_read=578610 bytes_retransmit=0 bytes_invalid=0 send_seq=4776 receive_seq=4776 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998447 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=49.6 th1: temp=48.7 th2: temp=50.7 th3: temp=49.0 sysload=0.24 cputime=135.213 memavail=7405864 print_time=1067.159 buffer_time=2.108 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1043.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14935989 bytes_read=1667643 bytes_retransmit=9 bytes_invalid=0 send_seq=255254 receive_seq=255254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=41289 freq=400016164 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7006 bytes_read=23604 bytes_retransmit=0 bytes_invalid=0 send_seq=1139 receive_seq=1139 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999207 adj=49997017 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=64218 bytes_read=2250305 bytes_retransmit=9 bytes_invalid=0 send_seq=8841 receive_seq=8841 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997286 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16098 bytes_read=131002 bytes_retransmit=9 bytes_invalid=0 send_seq=1882 receive_seq=1882 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997137 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7165 bytes_read=261965 bytes_retransmit=9 bytes_invalid=0 send_seq=1145 receive_seq=1145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997426 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7759 bytes_read=23184 bytes_retransmit=9 bytes_invalid=0 send_seq=1140 receive_seq=1140 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999384 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50835 bytes_read=578966 bytes_retransmit=0 bytes_invalid=0 send_seq=4777 receive_seq=4777 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998488 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.6 th1: temp=48.7 th2: temp=51.1 th3: temp=48.9 sysload=0.24 cputime=135.370 memavail=7405872 print_time=1068.235 buffer_time=2.183 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1044.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14960801 bytes_read=1670002 bytes_retransmit=9 bytes_invalid=0 send_seq=255661 receive_seq=255661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=43145 freq=400016133 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7012 bytes_read=23620 bytes_retransmit=0 bytes_invalid=0 send_seq=1140 receive_seq=1140 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49996892 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=64287 bytes_read=2253454 bytes_retransmit=9 bytes_invalid=0 send_seq=8851 receive_seq=8851 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997138 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16104 bytes_read=131102 bytes_retransmit=9 bytes_invalid=0 send_seq=1883 receive_seq=1883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997001 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7171 bytes_read=262214 bytes_retransmit=9 bytes_invalid=0 send_seq=1146 receive_seq=1146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997303 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7765 bytes_read=23200 bytes_retransmit=9 bytes_invalid=0 send_seq=1141 receive_seq=1141 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999357 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50841 bytes_read=579322 bytes_retransmit=0 bytes_invalid=0 send_seq=4778 receive_seq=4778 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998410 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.4 th1: temp=48.7 th2: temp=50.8 th3: temp=48.9 sysload=0.24 cputime=135.533 memavail=7400080 print_time=1069.312 buffer_time=2.259 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1045.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=14985562 bytes_read=1672363 bytes_retransmit=9 bytes_invalid=0 send_seq=256065 receive_seq=256065 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=45001 freq=400016100 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7018 bytes_read=23636 bytes_retransmit=0 bytes_invalid=0 send_seq=1141 receive_seq=1141 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997010 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=64363 bytes_read=2256569 bytes_retransmit=9 bytes_invalid=0 send_seq=8862 receive_seq=8862 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997278 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16110 bytes_read=131202 bytes_retransmit=9 bytes_invalid=0 send_seq=1884 receive_seq=1884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997156 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7177 bytes_read=262448 bytes_retransmit=9 bytes_invalid=0 send_seq=1147 receive_seq=1147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997427 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7771 bytes_read=23216 bytes_retransmit=9 bytes_invalid=0 send_seq=1142 receive_seq=1142 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999385 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50847 bytes_read=579678 bytes_retransmit=0 bytes_invalid=0 send_seq=4779 receive_seq=4779 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998485 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.7 th1: temp=48.8 th2: temp=50.9 th3: temp=48.9 sysload=0.24 cputime=135.685 memavail=7405748 print_time=1070.388 buffer_time=2.335 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1046.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15010369 bytes_read=1674703 bytes_retransmit=9 bytes_invalid=0 send_seq=256471 receive_seq=256471 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=46827 freq=400016072 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7024 bytes_read=23665 bytes_retransmit=0 bytes_invalid=0 send_seq=1142 receive_seq=1142 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997103 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=64439 bytes_read=2259727 bytes_retransmit=9 bytes_invalid=0 send_seq=8873 receive_seq=8873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997399 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16116 bytes_read=131330 bytes_retransmit=9 bytes_invalid=0 send_seq=1885 receive_seq=1885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997377 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7183 bytes_read=262742 bytes_retransmit=9 bytes_invalid=0 send_seq=1148 receive_seq=1148 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997512 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7777 bytes_read=23243 bytes_retransmit=9 bytes_invalid=0 send_seq=1143 receive_seq=1143 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999410 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50853 bytes_read=580034 bytes_retransmit=0 bytes_invalid=0 send_seq=4780 receive_seq=4780 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998540 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.6 th1: temp=49.1 th2: temp=51.1 th3: temp=48.9 sysload=0.22 cputime=135.840 memavail=7405748 print_time=1071.465 buffer_time=2.410 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1047.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15035213 bytes_read=1677067 bytes_retransmit=9 bytes_invalid=0 send_seq=256880 receive_seq=256879 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=48646 freq=400016045 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7030 bytes_read=23681 bytes_retransmit=0 bytes_invalid=0 send_seq=1143 receive_seq=1143 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997161 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=64515 bytes_read=2262843 bytes_retransmit=9 bytes_invalid=0 send_seq=8884 receive_seq=8884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997476 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16122 bytes_read=131444 bytes_retransmit=9 bytes_invalid=0 send_seq=1886 receive_seq=1886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997425 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7189 bytes_read=262976 bytes_retransmit=9 bytes_invalid=0 send_seq=1149 receive_seq=1149 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997562 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7783 bytes_read=23259 bytes_retransmit=9 bytes_invalid=0 send_seq=1144 receive_seq=1144 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999422 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50859 bytes_read=580390 bytes_retransmit=0 bytes_invalid=0 send_seq=4781 receive_seq=4781 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998578 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.6 th1: temp=48.7 th2: temp=50.9 th3: temp=49.0 sysload=0.22 cputime=135.990 memavail=7405748 print_time=1072.541 buffer_time=2.486 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1048.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15059988 bytes_read=1679432 bytes_retransmit=9 bytes_invalid=0 send_seq=257287 receive_seq=257287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=38308 freq=400016001 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7036 bytes_read=23697 bytes_retransmit=0 bytes_invalid=0 send_seq=1144 receive_seq=1144 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997208 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=64591 bytes_read=2265956 bytes_retransmit=9 bytes_invalid=0 send_seq=8895 receive_seq=8895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997536 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16128 bytes_read=131544 bytes_retransmit=9 bytes_invalid=0 send_seq=1887 receive_seq=1887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997473 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7195 bytes_read=263210 bytes_retransmit=9 bytes_invalid=0 send_seq=1150 receive_seq=1150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997606 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7789 bytes_read=23275 bytes_retransmit=9 bytes_invalid=0 send_seq=1145 receive_seq=1145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50865 bytes_read=580746 bytes_retransmit=0 bytes_invalid=0 send_seq=4782 receive_seq=4782 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998603 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=49.8 th1: temp=48.7 th2: temp=50.8 th3: temp=48.9 sysload=0.22 cputime=136.120 memavail=7405748 print_time=1073.079 buffer_time=2.024 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1049.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15084782 bytes_read=1681777 bytes_retransmit=9 bytes_invalid=0 send_seq=257694 receive_seq=257694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=40164 freq=400016043 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7042 bytes_read=23713 bytes_retransmit=0 bytes_invalid=0 send_seq=1145 receive_seq=1145 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997275 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=64667 bytes_read=2269099 bytes_retransmit=9 bytes_invalid=0 send_seq=8906 receive_seq=8906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63997600 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16134 bytes_read=131672 bytes_retransmit=9 bytes_invalid=0 send_seq=1888 receive_seq=1888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997562 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7201 bytes_read=263514 bytes_retransmit=9 bytes_invalid=0 send_seq=1151 receive_seq=1151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7795 bytes_read=23291 bytes_retransmit=9 bytes_invalid=0 send_seq=1146 receive_seq=1146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50871 bytes_read=581102 bytes_retransmit=0 bytes_invalid=0 send_seq=4783 receive_seq=4783 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998639 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.4 th1: temp=48.9 th2: temp=51.0 th3: temp=49.0 sysload=0.22 cputime=136.272 memavail=7405748 print_time=1074.156 buffer_time=2.100 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1050.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15110573 bytes_read=1684237 bytes_retransmit=9 bytes_invalid=0 send_seq=258118 receive_seq=258118 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=41092 freq=400016010 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7048 bytes_read=23729 bytes_retransmit=0 bytes_invalid=0 send_seq=1146 receive_seq=1146 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997199 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=64743 bytes_read=2272199 bytes_retransmit=9 bytes_invalid=0 send_seq=8917 receive_seq=8917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000179 adj=63997502 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16140 bytes_read=131765 bytes_retransmit=9 bytes_invalid=0 send_seq=1889 receive_seq=1889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997456 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7207 bytes_read=263732 bytes_retransmit=9 bytes_invalid=0 send_seq=1152 receive_seq=1152 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997626 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7801 bytes_read=23307 bytes_retransmit=9 bytes_invalid=0 send_seq=1147 receive_seq=1147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50877 bytes_read=581458 bytes_retransmit=0 bytes_invalid=0 send_seq=4784 receive_seq=4784 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998599 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.5 th1: temp=48.8 th2: temp=50.9 th3: temp=49.0 sysload=0.22 cputime=136.421 memavail=7405748 print_time=1075.232 buffer_time=2.176 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1051.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15135388 bytes_read=1686596 bytes_retransmit=9 bytes_invalid=0 send_seq=258526 receive_seq=258526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=42948 freq=400016073 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7054 bytes_read=23758 bytes_retransmit=0 bytes_invalid=0 send_seq=1147 receive_seq=1147 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997253 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=64819 bytes_read=2275314 bytes_retransmit=9 bytes_invalid=0 send_seq=8928 receive_seq=8928 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997580 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16146 bytes_read=131858 bytes_retransmit=9 bytes_invalid=0 send_seq=1890 receive_seq=1890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997501 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7213 bytes_read=263950 bytes_retransmit=9 bytes_invalid=0 send_seq=1153 receive_seq=1153 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997715 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7807 bytes_read=23334 bytes_retransmit=9 bytes_invalid=0 send_seq=1148 receive_seq=1148 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50883 bytes_read=581814 bytes_retransmit=0 bytes_invalid=0 send_seq=4785 receive_seq=4785 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998630 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=49.6 th1: temp=48.2 th2: temp=50.9 th3: temp=49.0 sysload=0.20 cputime=136.572 memavail=7405748 print_time=1076.309 buffer_time=2.252 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1052.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15160128 bytes_read=1688946 bytes_retransmit=9 bytes_invalid=0 send_seq=258934 receive_seq=258934 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=44836 freq=400016032 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7060 bytes_read=23774 bytes_retransmit=0 bytes_invalid=0 send_seq=1148 receive_seq=1148 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997149 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=64895 bytes_read=2278496 bytes_retransmit=9 bytes_invalid=0 send_seq=8939 receive_seq=8939 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000177 adj=63997456 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16152 bytes_read=131991 bytes_retransmit=9 bytes_invalid=0 send_seq=1891 receive_seq=1891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997355 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7219 bytes_read=264224 bytes_retransmit=9 bytes_invalid=0 send_seq=1154 receive_seq=1154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997598 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7813 bytes_read=23350 bytes_retransmit=9 bytes_invalid=0 send_seq=1149 receive_seq=1149 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999420 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50889 bytes_read=582170 bytes_retransmit=0 bytes_invalid=0 send_seq=4786 receive_seq=4786 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998576 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=49.5 th1: temp=48.8 th2: temp=51.0 th3: temp=49.0 sysload=0.20 cputime=136.722 memavail=7405748 print_time=1077.385 buffer_time=2.328 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 1053.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15185032 bytes_read=1691325 bytes_retransmit=9 bytes_invalid=0 send_seq=259343 receive_seq=259342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=46625 freq=400016003 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7066 bytes_read=23790 bytes_retransmit=0 bytes_invalid=0 send_seq=1149 receive_seq=1149 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997221 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=64971 bytes_read=2281593 bytes_retransmit=9 bytes_invalid=0 send_seq=8950 receive_seq=8950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000177 adj=63997554 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16158 bytes_read=132084 bytes_retransmit=9 bytes_invalid=0 send_seq=1892 receive_seq=1892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997436 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7225 bytes_read=264442 bytes_retransmit=9 bytes_invalid=0 send_seq=1155 receive_seq=1155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7819 bytes_read=23366 bytes_retransmit=9 bytes_invalid=0 send_seq=1150 receive_seq=1150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50895 bytes_read=582526 bytes_retransmit=0 bytes_invalid=0 send_seq=4787 receive_seq=4787 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998621 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=49.5 th1: temp=48.7 th2: temp=51.0 th3: temp=49.0 sysload=0.20 cputime=136.865 memavail=7405748 print_time=1078.462 buffer_time=2.403 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1054.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15209884 bytes_read=1693675 bytes_retransmit=9 bytes_invalid=0 send_seq=259750 receive_seq=259750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=48414 freq=400015976 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7072 bytes_read=23806 bytes_retransmit=0 bytes_invalid=0 send_seq=1150 receive_seq=1150 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997260 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65047 bytes_read=2284701 bytes_retransmit=9 bytes_invalid=0 send_seq=8961 receive_seq=8961 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000176 adj=63997609 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16164 bytes_read=132182 bytes_retransmit=9 bytes_invalid=0 send_seq=1893 receive_seq=1893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997478 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7231 bytes_read=264675 bytes_retransmit=9 bytes_invalid=0 send_seq=1156 receive_seq=1156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7825 bytes_read=23382 bytes_retransmit=9 bytes_invalid=0 send_seq=1151 receive_seq=1151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50901 bytes_read=582882 bytes_retransmit=0 bytes_invalid=0 send_seq=4788 receive_seq=4788 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998647 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=49.5 th1: temp=48.9 th2: temp=50.9 th3: temp=48.9 sysload=0.20 cputime=137.017 memavail=7405748 print_time=1079.538 buffer_time=2.476 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1055.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15234705 bytes_read=1696041 bytes_retransmit=9 bytes_invalid=0 send_seq=260158 receive_seq=260158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=38041 freq=400015953 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7078 bytes_read=23822 bytes_retransmit=0 bytes_invalid=0 send_seq=1151 receive_seq=1151 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997287 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65123 bytes_read=2287844 bytes_retransmit=9 bytes_invalid=0 send_seq=8972 receive_seq=8972 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997648 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16170 bytes_read=132310 bytes_retransmit=9 bytes_invalid=0 send_seq=1894 receive_seq=1894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997537 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7237 bytes_read=264962 bytes_retransmit=9 bytes_invalid=0 send_seq=1157 receive_seq=1157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997704 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7831 bytes_read=23398 bytes_retransmit=9 bytes_invalid=0 send_seq=1152 receive_seq=1152 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50907 bytes_read=583238 bytes_retransmit=0 bytes_invalid=0 send_seq=4789 receive_seq=4789 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998664 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=49.7 th1: temp=48.8 th2: temp=50.9 th3: temp=48.9 sysload=0.20 cputime=137.152 memavail=7404744 print_time=1080.077 buffer_time=2.013 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1056.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15259517 bytes_read=1698415 bytes_retransmit=9 bytes_invalid=0 send_seq=260565 receive_seq=260565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=39897 freq=400016016 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7084 bytes_read=23851 bytes_retransmit=0 bytes_invalid=0 send_seq=1152 receive_seq=1152 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997324 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65192 bytes_read=2290953 bytes_retransmit=9 bytes_invalid=0 send_seq=8982 receive_seq=8982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000174 adj=63997684 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16176 bytes_read=132410 bytes_retransmit=9 bytes_invalid=0 send_seq=1895 receive_seq=1895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997575 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7243 bytes_read=265196 bytes_retransmit=9 bytes_invalid=0 send_seq=1158 receive_seq=1158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997726 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7837 bytes_read=23425 bytes_retransmit=9 bytes_invalid=0 send_seq=1153 receive_seq=1153 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50913 bytes_read=583594 bytes_retransmit=0 bytes_invalid=0 send_seq=4790 receive_seq=4790 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998686 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.6 th2: temp=50.9 th3: temp=49.0 sysload=0.19 cputime=137.307 memavail=7404744 print_time=1081.153 buffer_time=2.089 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1057.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15285319 bytes_read=1700840 bytes_retransmit=9 bytes_invalid=0 send_seq=260988 receive_seq=260988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=40825 freq=400015999 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7090 bytes_read=23867 bytes_retransmit=0 bytes_invalid=0 send_seq=1153 receive_seq=1153 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997215 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65268 bytes_read=2294067 bytes_retransmit=9 bytes_invalid=0 send_seq=8993 receive_seq=8993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000174 adj=63997541 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16182 bytes_read=132524 bytes_retransmit=9 bytes_invalid=0 send_seq=1896 receive_seq=1896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997418 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7249 bytes_read=265430 bytes_retransmit=9 bytes_invalid=0 send_seq=1159 receive_seq=1159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997609 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7843 bytes_read=23441 bytes_retransmit=9 bytes_invalid=0 send_seq=1154 receive_seq=1154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50919 bytes_read=583968 bytes_retransmit=0 bytes_invalid=0 send_seq=4791 receive_seq=4791 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998610 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=49.4 th1: temp=48.8 th2: temp=50.9 th3: temp=49.0 sysload=0.19 cputime=137.459 memavail=7404744 print_time=1082.229 buffer_time=2.164 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1058.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15310090 bytes_read=1703180 bytes_retransmit=9 bytes_invalid=0 send_seq=261394 receive_seq=261394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=42681 freq=400015969 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7096 bytes_read=23883 bytes_retransmit=0 bytes_invalid=0 send_seq=1154 receive_seq=1154 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997243 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65344 bytes_read=2297269 bytes_retransmit=9 bytes_invalid=0 send_seq=9004 receive_seq=9004 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000174 adj=63997584 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16188 bytes_read=132652 bytes_retransmit=9 bytes_invalid=0 send_seq=1897 receive_seq=1897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997458 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7255 bytes_read=265724 bytes_retransmit=9 bytes_invalid=0 send_seq=1160 receive_seq=1160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7849 bytes_read=23457 bytes_retransmit=9 bytes_invalid=0 send_seq=1155 receive_seq=1155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50925 bytes_read=584324 bytes_retransmit=0 bytes_invalid=0 send_seq=4792 receive_seq=4792 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998642 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=49.6 th1: temp=48.7 th2: temp=51.0 th3: temp=49.0 sysload=0.19 cputime=137.607 memavail=7404744 print_time=1083.306 buffer_time=2.241 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1059.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15334912 bytes_read=1705564 bytes_retransmit=9 bytes_invalid=0 send_seq=261803 receive_seq=261803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=44537 freq=400015926 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7102 bytes_read=23899 bytes_retransmit=0 bytes_invalid=0 send_seq=1155 receive_seq=1155 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997284 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65420 bytes_read=2300383 bytes_retransmit=9 bytes_invalid=0 send_seq=9015 receive_seq=9015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997652 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16194 bytes_read=132752 bytes_retransmit=9 bytes_invalid=0 send_seq=1898 receive_seq=1898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7261 bytes_read=265973 bytes_retransmit=9 bytes_invalid=0 send_seq=1161 receive_seq=1161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997705 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7855 bytes_read=23473 bytes_retransmit=9 bytes_invalid=0 send_seq=1156 receive_seq=1156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50931 bytes_read=584680 bytes_retransmit=0 bytes_invalid=0 send_seq=4793 receive_seq=4793 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998671 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.7 th1: temp=48.7 th2: temp=50.8 th3: temp=49.0 sysload=0.19 cputime=137.758 memavail=7404784 print_time=1084.382 buffer_time=2.316 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1060.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15359706 bytes_read=1707925 bytes_retransmit=9 bytes_invalid=0 send_seq=262210 receive_seq=262210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=46393 freq=400015897 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7108 bytes_read=23915 bytes_retransmit=0 bytes_invalid=0 send_seq=1156 receive_seq=1156 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997336 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65496 bytes_read=2303496 bytes_retransmit=9 bytes_invalid=0 send_seq=9026 receive_seq=9026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000174 adj=63997733 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16200 bytes_read=132852 bytes_retransmit=9 bytes_invalid=0 send_seq=1899 receive_seq=1899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997566 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7267 bytes_read=266207 bytes_retransmit=9 bytes_invalid=0 send_seq=1162 receive_seq=1162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997738 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7861 bytes_read=23489 bytes_retransmit=9 bytes_invalid=0 send_seq=1157 receive_seq=1157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50937 bytes_read=585036 bytes_retransmit=0 bytes_invalid=0 send_seq=4794 receive_seq=4794 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998699 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=49.6 th1: temp=48.9 th2: temp=51.0 th3: temp=48.8 sysload=0.19 cputime=137.907 memavail=7404804 print_time=1085.459 buffer_time=2.393 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1061.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15384495 bytes_read=1710265 bytes_retransmit=9 bytes_invalid=0 send_seq=262616 receive_seq=262616 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=48249 freq=400015881 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7114 bytes_read=23944 bytes_retransmit=0 bytes_invalid=0 send_seq=1157 receive_seq=1157 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997358 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65572 bytes_read=2306654 bytes_retransmit=9 bytes_invalid=0 send_seq=9037 receive_seq=9037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000174 adj=63997756 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16206 bytes_read=132980 bytes_retransmit=9 bytes_invalid=0 send_seq=1900 receive_seq=1900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000018 adj=63997587 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7273 bytes_read=266501 bytes_retransmit=9 bytes_invalid=0 send_seq=1163 receive_seq=1163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997744 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7867 bytes_read=23516 bytes_retransmit=9 bytes_invalid=0 send_seq=1158 receive_seq=1158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999469 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50943 bytes_read=585392 bytes_retransmit=0 bytes_invalid=0 send_seq=4795 receive_seq=4795 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998727 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.6 th1: temp=48.5 th2: temp=50.9 th3: temp=49.3 sysload=0.17 cputime=138.066 memavail=7402284 print_time=1086.535 buffer_time=2.469 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1062.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15409246 bytes_read=1712629 bytes_retransmit=9 bytes_invalid=0 send_seq=263022 receive_seq=263022 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=37876 freq=400015852 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7120 bytes_read=23960 bytes_retransmit=0 bytes_invalid=0 send_seq=1158 receive_seq=1158 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997355 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65648 bytes_read=2309767 bytes_retransmit=9 bytes_invalid=0 send_seq=9048 receive_seq=9048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997753 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16212 bytes_read=133094 bytes_retransmit=9 bytes_invalid=0 send_seq=1901 receive_seq=1901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000018 adj=63997580 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7279 bytes_read=266735 bytes_retransmit=9 bytes_invalid=0 send_seq=1164 receive_seq=1164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997764 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7873 bytes_read=23532 bytes_retransmit=9 bytes_invalid=0 send_seq=1159 receive_seq=1159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999466 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50949 bytes_read=585748 bytes_retransmit=0 bytes_invalid=0 send_seq=4796 receive_seq=4796 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998721 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=49.5 th1: temp=48.8 th2: temp=51.1 th3: temp=49.0 sysload=0.17 cputime=138.205 memavail=7407688 print_time=1087.074 buffer_time=2.007 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1063.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15434040 bytes_read=1714974 bytes_retransmit=9 bytes_invalid=0 send_seq=263429 receive_seq=263429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=39732 freq=400015845 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7126 bytes_read=23976 bytes_retransmit=0 bytes_invalid=0 send_seq=1159 receive_seq=1159 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997394 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65724 bytes_read=2312881 bytes_retransmit=9 bytes_invalid=0 send_seq=9059 receive_seq=9059 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000175 adj=63997815 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16218 bytes_read=133194 bytes_retransmit=9 bytes_invalid=0 send_seq=1902 receive_seq=1902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997627 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7285 bytes_read=266969 bytes_retransmit=9 bytes_invalid=0 send_seq=1165 receive_seq=1165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997795 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7879 bytes_read=23548 bytes_retransmit=9 bytes_invalid=0 send_seq=1160 receive_seq=1160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999474 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50955 bytes_read=586104 bytes_retransmit=0 bytes_invalid=0 send_seq=4797 receive_seq=4797 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998744 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.6 th1: temp=48.6 th2: temp=51.2 th3: temp=48.9 sysload=0.17 cputime=138.358 memavail=7407688 print_time=1088.150 buffer_time=2.083 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1064.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15459832 bytes_read=1717389 bytes_retransmit=9 bytes_invalid=0 send_seq=263850 receive_seq=263850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=40660 freq=400015828 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7132 bytes_read=23992 bytes_retransmit=0 bytes_invalid=0 send_seq=1160 receive_seq=1160 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997375 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65800 bytes_read=2316026 bytes_retransmit=9 bytes_invalid=0 send_seq=9070 receive_seq=9070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000174 adj=63997809 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16224 bytes_read=133322 bytes_retransmit=9 bytes_invalid=0 send_seq=1903 receive_seq=1903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997647 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7291 bytes_read=267278 bytes_retransmit=9 bytes_invalid=0 send_seq=1166 receive_seq=1166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997777 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7885 bytes_read=23564 bytes_retransmit=9 bytes_invalid=0 send_seq=1161 receive_seq=1161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999471 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50961 bytes_read=586460 bytes_retransmit=0 bytes_invalid=0 send_seq=4798 receive_seq=4798 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998738 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.4 th1: temp=48.4 th2: temp=50.9 th3: temp=48.9 sysload=0.17 cputime=138.516 memavail=7407688 print_time=1089.227 buffer_time=2.159 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1065.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15484616 bytes_read=1719764 bytes_retransmit=9 bytes_invalid=0 send_seq=264255 receive_seq=264254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=42516 freq=400015811 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7138 bytes_read=24008 bytes_retransmit=0 bytes_invalid=0 send_seq=1161 receive_seq=1161 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997361 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65876 bytes_read=2319140 bytes_retransmit=9 bytes_invalid=0 send_seq=9081 receive_seq=9081 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000179 adj=63997796 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16230 bytes_read=133422 bytes_retransmit=9 bytes_invalid=0 send_seq=1904 receive_seq=1904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000018 adj=63997639 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7297 bytes_read=267512 bytes_retransmit=9 bytes_invalid=0 send_seq=1167 receive_seq=1167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997771 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7891 bytes_read=23580 bytes_retransmit=9 bytes_invalid=0 send_seq=1162 receive_seq=1162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999472 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50967 bytes_read=586816 bytes_retransmit=0 bytes_invalid=0 send_seq=4799 receive_seq=4799 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998738 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=49.4 th1: temp=48.6 th2: temp=51.2 th3: temp=48.9 sysload=0.17 cputime=138.666 memavail=7407192 print_time=1090.303 buffer_time=2.235 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1066.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15509415 bytes_read=1722114 bytes_retransmit=9 bytes_invalid=0 send_seq=264663 receive_seq=264662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=44372 freq=400015803 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7144 bytes_read=24037 bytes_retransmit=0 bytes_invalid=0 send_seq=1162 receive_seq=1162 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997344 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65952 bytes_read=2322329 bytes_retransmit=9 bytes_invalid=0 send_seq=9092 receive_seq=9092 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000178 adj=63997856 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16236 bytes_read=133522 bytes_retransmit=9 bytes_invalid=0 send_seq=1905 receive_seq=1905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997626 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7303 bytes_read=267746 bytes_retransmit=9 bytes_invalid=0 send_seq=1168 receive_seq=1168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997802 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7897 bytes_read=23607 bytes_retransmit=9 bytes_invalid=0 send_seq=1163 receive_seq=1163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999473 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50973 bytes_read=587172 bytes_retransmit=0 bytes_invalid=0 send_seq=4800 receive_seq=4800 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998730 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=49.8 th1: temp=48.8 th2: temp=51.3 th3: temp=49.0 sysload=0.32 cputime=138.813 memavail=7407204 print_time=1091.379 buffer_time=2.311 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1067.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15534199 bytes_read=1724454 bytes_retransmit=9 bytes_invalid=0 send_seq=265068 receive_seq=265068 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=46228 freq=400015773 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7150 bytes_read=24053 bytes_retransmit=0 bytes_invalid=0 send_seq=1163 receive_seq=1163 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999207 adj=49997325 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66028 bytes_read=2325472 bytes_retransmit=9 bytes_invalid=0 send_seq=9103 receive_seq=9103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000179 adj=63997816 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16242 bytes_read=133664 bytes_retransmit=9 bytes_invalid=0 send_seq=1906 receive_seq=1906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997705 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7309 bytes_read=268040 bytes_retransmit=9 bytes_invalid=0 send_seq=1169 receive_seq=1169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997797 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7903 bytes_read=23623 bytes_retransmit=9 bytes_invalid=0 send_seq=1164 receive_seq=1164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999467 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50979 bytes_read=587528 bytes_retransmit=0 bytes_invalid=0 send_seq=4801 receive_seq=4801 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998713 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.5 th1: temp=48.9 th2: temp=51.0 th3: temp=49.2 sysload=0.32 cputime=138.963 memavail=7407204 print_time=1092.456 buffer_time=2.388 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1068.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15558983 bytes_read=1726818 bytes_retransmit=9 bytes_invalid=0 send_seq=265473 receive_seq=265473 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=48117 freq=400015753 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7156 bytes_read=24069 bytes_retransmit=0 bytes_invalid=0 send_seq=1164 receive_seq=1164 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999205 adj=49997329 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66097 bytes_read=2328561 bytes_retransmit=9 bytes_invalid=0 send_seq=9113 receive_seq=9113 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000179 adj=63997842 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16248 bytes_read=133764 bytes_retransmit=9 bytes_invalid=0 send_seq=1907 receive_seq=1907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997714 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7315 bytes_read=268274 bytes_retransmit=9 bytes_invalid=0 send_seq=1170 receive_seq=1170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997802 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7909 bytes_read=23639 bytes_retransmit=9 bytes_invalid=0 send_seq=1165 receive_seq=1165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999487 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50985 bytes_read=587884 bytes_retransmit=0 bytes_invalid=0 send_seq=4802 receive_seq=4802 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998729 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.6 th1: temp=48.9 th2: temp=51.1 th3: temp=49.0 sysload=0.32 cputime=139.110 memavail=7407204 print_time=1093.532 buffer_time=2.464 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1069.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15583718 bytes_read=1729138 bytes_retransmit=9 bytes_invalid=0 send_seq=265875 receive_seq=265875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=37779 freq=400015748 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7162 bytes_read=24085 bytes_retransmit=0 bytes_invalid=0 send_seq=1165 receive_seq=1165 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999203 adj=49997320 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66173 bytes_read=2331674 bytes_retransmit=9 bytes_invalid=0 send_seq=9124 receive_seq=9124 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000181 adj=63997834 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16254 bytes_read=133864 bytes_retransmit=9 bytes_invalid=0 send_seq=1908 receive_seq=1908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997693 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7321 bytes_read=268523 bytes_retransmit=9 bytes_invalid=0 send_seq=1171 receive_seq=1171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997807 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7915 bytes_read=23655 bytes_retransmit=9 bytes_invalid=0 send_seq=1166 receive_seq=1166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999487 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50991 bytes_read=588240 bytes_retransmit=0 bytes_invalid=0 send_seq=4803 receive_seq=4803 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998769 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.8 th1: temp=48.9 th2: temp=51.0 th3: temp=49.0 sysload=0.32 cputime=139.239 memavail=7407204 print_time=1094.071 buffer_time=2.002 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1070.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15608579 bytes_read=1731509 bytes_retransmit=9 bytes_invalid=0 send_seq=266284 receive_seq=266284 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=39598 freq=400015748 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7168 bytes_read=24101 bytes_retransmit=0 bytes_invalid=0 send_seq=1166 receive_seq=1166 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999201 adj=49997305 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66249 bytes_read=2334816 bytes_retransmit=9 bytes_invalid=0 send_seq=9135 receive_seq=9135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000181 adj=63997872 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16260 bytes_read=133992 bytes_retransmit=9 bytes_invalid=0 send_seq=1909 receive_seq=1909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997689 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7327 bytes_read=268817 bytes_retransmit=9 bytes_invalid=0 send_seq=1172 receive_seq=1172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997820 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7921 bytes_read=23671 bytes_retransmit=9 bytes_invalid=0 send_seq=1167 receive_seq=1167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999487 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=50997 bytes_read=588596 bytes_retransmit=0 bytes_invalid=0 send_seq=4804 receive_seq=4804 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998768 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.7 th1: temp=48.8 th2: temp=51.2 th3: temp=49.1 sysload=0.32 cputime=139.389 memavail=7407204 print_time=1095.147 buffer_time=2.078 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1071.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15634296 bytes_read=1733953 bytes_retransmit=9 bytes_invalid=0 send_seq=266705 receive_seq=266705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=40563 freq=400015734 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7174 bytes_read=24130 bytes_retransmit=0 bytes_invalid=0 send_seq=1167 receive_seq=1167 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999198 adj=49997272 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66325 bytes_read=2337947 bytes_retransmit=9 bytes_invalid=0 send_seq=9146 receive_seq=9146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997843 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16266 bytes_read=134092 bytes_retransmit=9 bytes_invalid=0 send_seq=1910 receive_seq=1910 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997757 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7333 bytes_read=269051 bytes_retransmit=9 bytes_invalid=0 send_seq=1173 receive_seq=1173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997873 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7927 bytes_read=23698 bytes_retransmit=9 bytes_invalid=0 send_seq=1168 receive_seq=1168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999482 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51003 bytes_read=588952 bytes_retransmit=0 bytes_invalid=0 send_seq=4805 receive_seq=4805 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998761 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.6 th1: temp=49.0 th2: temp=51.0 th3: temp=48.9 sysload=0.29 cputime=139.538 memavail=7407204 print_time=1096.224 buffer_time=2.154 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1072.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15659070 bytes_read=1736276 bytes_retransmit=9 bytes_invalid=0 send_seq=267108 receive_seq=267108 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=42449 freq=400015912 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7180 bytes_read=24146 bytes_retransmit=0 bytes_invalid=0 send_seq=1168 receive_seq=1168 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999195 adj=49997250 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66401 bytes_read=2341061 bytes_retransmit=9 bytes_invalid=0 send_seq=9157 receive_seq=9157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997843 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16272 bytes_read=134206 bytes_retransmit=9 bytes_invalid=0 send_seq=1911 receive_seq=1911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997714 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7339 bytes_read=269285 bytes_retransmit=9 bytes_invalid=0 send_seq=1174 receive_seq=1174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997842 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7933 bytes_read=23714 bytes_retransmit=9 bytes_invalid=0 send_seq=1169 receive_seq=1169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999477 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51009 bytes_read=589308 bytes_retransmit=0 bytes_invalid=0 send_seq=4806 receive_seq=4806 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998747 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.8 th1: temp=48.6 th2: temp=51.1 th3: temp=49.1 sysload=0.29 cputime=139.686 memavail=7407204 print_time=1097.300 buffer_time=2.230 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1073.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15683869 bytes_read=1738623 bytes_retransmit=9 bytes_invalid=0 send_seq=267516 receive_seq=267516 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=44275 freq=400015876 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7186 bytes_read=24162 bytes_retransmit=0 bytes_invalid=0 send_seq=1169 receive_seq=1169 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999191 adj=49996941 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66477 bytes_read=2344202 bytes_retransmit=9 bytes_invalid=0 send_seq=9168 receive_seq=9168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997457 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16278 bytes_read=134334 bytes_retransmit=9 bytes_invalid=0 send_seq=1912 receive_seq=1912 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997315 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7345 bytes_read=269579 bytes_retransmit=9 bytes_invalid=0 send_seq=1175 receive_seq=1175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997526 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7939 bytes_read=23730 bytes_retransmit=9 bytes_invalid=0 send_seq=1170 receive_seq=1170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999405 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51015 bytes_read=589664 bytes_retransmit=0 bytes_invalid=0 send_seq=4807 receive_seq=4807 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998554 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=49.7 th1: temp=48.8 th2: temp=50.9 th3: temp=49.2 sysload=0.29 cputime=139.833 memavail=7406980 print_time=1098.376 buffer_time=2.306 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1074.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15708703 bytes_read=1740962 bytes_retransmit=9 bytes_invalid=0 send_seq=267916 receive_seq=267916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=46094 freq=400015862 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7192 bytes_read=24178 bytes_retransmit=0 bytes_invalid=0 send_seq=1170 receive_seq=1170 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999188 adj=49997010 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66553 bytes_read=2347374 bytes_retransmit=9 bytes_invalid=0 send_seq=9179 receive_seq=9179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997573 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16284 bytes_read=134434 bytes_retransmit=9 bytes_invalid=0 send_seq=1913 receive_seq=1913 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997420 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7351 bytes_read=269828 bytes_retransmit=9 bytes_invalid=0 send_seq=1176 receive_seq=1176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997587 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7945 bytes_read=23746 bytes_retransmit=9 bytes_invalid=0 send_seq=1171 receive_seq=1171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999423 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51021 bytes_read=590020 bytes_retransmit=0 bytes_invalid=0 send_seq=4808 receive_seq=4808 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998610 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.5 th1: temp=49.2 th2: temp=51.0 th3: temp=49.1 sysload=0.29 cputime=139.985 memavail=7406980 print_time=1099.453 buffer_time=2.380 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 1075.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15733602 bytes_read=1743328 bytes_retransmit=9 bytes_invalid=0 send_seq=268324 receive_seq=268324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=47852 freq=400015843 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7198 bytes_read=24194 bytes_retransmit=0 bytes_invalid=0 send_seq=1171 receive_seq=1171 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999184 adj=49997031 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66629 bytes_read=2350487 bytes_retransmit=9 bytes_invalid=0 send_seq=9190 receive_seq=9190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997617 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16290 bytes_read=134534 bytes_retransmit=9 bytes_invalid=0 send_seq=1914 receive_seq=1914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997450 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7357 bytes_read=270062 bytes_retransmit=9 bytes_invalid=0 send_seq=1177 receive_seq=1177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7951 bytes_read=23762 bytes_retransmit=9 bytes_invalid=0 send_seq=1172 receive_seq=1172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51027 bytes_read=590376 bytes_retransmit=0 bytes_invalid=0 send_seq=4809 receive_seq=4809 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998630 coil_temp=17.6 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=49.3 th1: temp=48.8 th2: temp=51.1 th3: temp=49.1 sysload=0.29 cputime=140.138 memavail=7407004 print_time=1100.529 buffer_time=2.453 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 1076.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15758533 bytes_read=1745673 bytes_retransmit=9 bytes_invalid=0 send_seq=268731 receive_seq=268731 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=49561 freq=400016028 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7204 bytes_read=24223 bytes_retransmit=0 bytes_invalid=0 send_seq=1172 receive_seq=1172 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999180 adj=49997051 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66705 bytes_read=2353645 bytes_retransmit=9 bytes_invalid=0 send_seq=9201 receive_seq=9201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997658 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16296 bytes_read=134662 bytes_retransmit=9 bytes_invalid=0 send_seq=1915 receive_seq=1915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997501 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7363 bytes_read=270356 bytes_retransmit=9 bytes_invalid=0 send_seq=1178 receive_seq=1178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7957 bytes_read=23789 bytes_retransmit=9 bytes_invalid=0 send_seq=1173 receive_seq=1173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51033 bytes_read=590732 bytes_retransmit=0 bytes_invalid=0 send_seq=4810 receive_seq=4810 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998649 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.8 th1: temp=48.8 th2: temp=51.0 th3: temp=49.2 sysload=0.27 cputime=140.289 memavail=7407004 print_time=1101.606 buffer_time=2.523 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1077.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15783327 bytes_read=1748047 bytes_retransmit=9 bytes_invalid=0 send_seq=269138 receive_seq=269138 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=39201 freq=400016010 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7210 bytes_read=24239 bytes_retransmit=0 bytes_invalid=0 send_seq=1173 receive_seq=1173 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999176 adj=49996790 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66781 bytes_read=2356758 bytes_retransmit=9 bytes_invalid=0 send_seq=9212 receive_seq=9212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000182 adj=63997337 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16302 bytes_read=134776 bytes_retransmit=9 bytes_invalid=0 send_seq=1916 receive_seq=1916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997167 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7369 bytes_read=270590 bytes_retransmit=9 bytes_invalid=0 send_seq=1179 receive_seq=1179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997424 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7963 bytes_read=23805 bytes_retransmit=9 bytes_invalid=0 send_seq=1174 receive_seq=1174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999377 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51039 bytes_read=591088 bytes_retransmit=0 bytes_invalid=0 send_seq=4811 receive_seq=4811 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998541 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=49.7 th1: temp=49.0 th2: temp=51.1 th3: temp=49.2 sysload=0.27 cputime=140.429 memavail=7407028 print_time=1102.144 buffer_time=2.061 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1078.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15808746 bytes_read=1750437 bytes_retransmit=9 bytes_invalid=0 send_seq=269554 receive_seq=269554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=40461 freq=400015968 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7216 bytes_read=24255 bytes_retransmit=0 bytes_invalid=0 send_seq=1174 receive_seq=1174 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999172 adj=49996770 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66857 bytes_read=2359934 bytes_retransmit=9 bytes_invalid=0 send_seq=9223 receive_seq=9223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997365 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16308 bytes_read=134876 bytes_retransmit=9 bytes_invalid=0 send_seq=1917 receive_seq=1917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997218 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7375 bytes_read=270824 bytes_retransmit=9 bytes_invalid=0 send_seq=1180 receive_seq=1180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997432 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7969 bytes_read=23821 bytes_retransmit=9 bytes_invalid=0 send_seq=1175 receive_seq=1175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999381 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51045 bytes_read=591444 bytes_retransmit=0 bytes_invalid=0 send_seq=4812 receive_seq=4812 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998553 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.8 th1: temp=48.9 th2: temp=51.2 th3: temp=49.2 sysload=0.27 cputime=140.583 memavail=7407028 print_time=1103.221 buffer_time=2.137 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1079.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15833936 bytes_read=1752807 bytes_retransmit=9 bytes_invalid=0 send_seq=269967 receive_seq=269966 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=41985 freq=400015951 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7222 bytes_read=24271 bytes_retransmit=0 bytes_invalid=0 send_seq=1175 receive_seq=1175 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999169 adj=49996832 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66933 bytes_read=2363078 bytes_retransmit=9 bytes_invalid=0 send_seq=9234 receive_seq=9234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997513 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16314 bytes_read=135004 bytes_retransmit=9 bytes_invalid=0 send_seq=1918 receive_seq=1918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997314 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7381 bytes_read=271133 bytes_retransmit=9 bytes_invalid=0 send_seq=1181 receive_seq=1181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997509 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7975 bytes_read=23837 bytes_retransmit=9 bytes_invalid=0 send_seq=1176 receive_seq=1176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999403 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51051 bytes_read=591800 bytes_retransmit=0 bytes_invalid=0 send_seq=4813 receive_seq=4813 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998600 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.9 th1: temp=48.9 th2: temp=51.2 th3: temp=49.2 sysload=0.27 cputime=140.752 memavail=7406380 print_time=1104.297 buffer_time=2.213 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1080.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15858725 bytes_read=1755197 bytes_retransmit=9 bytes_invalid=0 send_seq=270373 receive_seq=270373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=43841 freq=400015926 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7228 bytes_read=24287 bytes_retransmit=0 bytes_invalid=0 send_seq=1176 receive_seq=1176 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999164 adj=49996901 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67002 bytes_read=2366168 bytes_retransmit=9 bytes_invalid=0 send_seq=9244 receive_seq=9244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997570 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16320 bytes_read=135104 bytes_retransmit=9 bytes_invalid=0 send_seq=1919 receive_seq=1919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997370 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7387 bytes_read=271367 bytes_retransmit=9 bytes_invalid=0 send_seq=1182 receive_seq=1182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997545 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7981 bytes_read=23853 bytes_retransmit=9 bytes_invalid=0 send_seq=1177 receive_seq=1177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999416 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51057 bytes_read=592156 bytes_retransmit=0 bytes_invalid=0 send_seq=4814 receive_seq=4814 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998622 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.8 th1: temp=49.0 th2: temp=51.2 th3: temp=49.1 sysload=0.27 cputime=140.900 memavail=7406156 print_time=1105.374 buffer_time=2.288 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1081.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15883519 bytes_read=1757542 bytes_retransmit=9 bytes_invalid=0 send_seq=270780 receive_seq=270780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=45697 freq=400016000 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7234 bytes_read=24316 bytes_retransmit=0 bytes_invalid=0 send_seq=1177 receive_seq=1177 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999160 adj=49996949 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67078 bytes_read=2369302 bytes_retransmit=9 bytes_invalid=0 send_seq=9255 receive_seq=9255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997623 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16326 bytes_read=135204 bytes_retransmit=9 bytes_invalid=0 send_seq=1920 receive_seq=1920 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997426 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7393 bytes_read=271601 bytes_retransmit=9 bytes_invalid=0 send_seq=1183 receive_seq=1183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997584 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7987 bytes_read=23880 bytes_retransmit=9 bytes_invalid=0 send_seq=1178 receive_seq=1178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51063 bytes_read=592512 bytes_retransmit=0 bytes_invalid=0 send_seq=4815 receive_seq=4815 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998644 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.8 th1: temp=48.9 th2: temp=51.0 th3: temp=49.3 sysload=0.25 cputime=141.050 memavail=7407888 print_time=1106.450 buffer_time=2.364 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1082.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15908308 bytes_read=1759877 bytes_retransmit=9 bytes_invalid=0 send_seq=271186 receive_seq=271185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=47553 freq=400015974 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7240 bytes_read=24332 bytes_retransmit=0 bytes_invalid=0 send_seq=1178 receive_seq=1178 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999155 adj=49996844 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67154 bytes_read=2372446 bytes_retransmit=9 bytes_invalid=0 send_seq=9266 receive_seq=9266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997489 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16332 bytes_read=135346 bytes_retransmit=9 bytes_invalid=0 send_seq=1921 receive_seq=1921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997293 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7399 bytes_read=271895 bytes_retransmit=9 bytes_invalid=0 send_seq=1184 receive_seq=1184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997480 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7993 bytes_read=23896 bytes_retransmit=9 bytes_invalid=0 send_seq=1179 receive_seq=1179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999403 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51069 bytes_read=592868 bytes_retransmit=0 bytes_invalid=0 send_seq=4816 receive_seq=4816 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998572 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=49.9 th1: temp=49.1 th2: temp=51.2 th3: temp=49.1 sysload=0.25 cputime=141.199 memavail=7407888 print_time=1107.526 buffer_time=2.440 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 1083.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15933054 bytes_read=1762242 bytes_retransmit=9 bytes_invalid=0 send_seq=271591 receive_seq=271591 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=49396 freq=400016074 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7246 bytes_read=24348 bytes_retransmit=0 bytes_invalid=0 send_seq=1179 receive_seq=1179 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999151 adj=49996891 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67230 bytes_read=2375562 bytes_retransmit=9 bytes_invalid=0 send_seq=9277 receive_seq=9277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997558 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16338 bytes_read=135446 bytes_retransmit=9 bytes_invalid=0 send_seq=1922 receive_seq=1922 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997446 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7405 bytes_read=272129 bytes_retransmit=9 bytes_invalid=0 send_seq=1185 receive_seq=1185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997534 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=7999 bytes_read=23912 bytes_retransmit=9 bytes_invalid=0 send_seq=1180 receive_seq=1180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999416 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51075 bytes_read=593224 bytes_retransmit=0 bytes_invalid=0 send_seq=4817 receive_seq=4817 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998600 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.8 th1: temp=49.0 th2: temp=51.4 th3: temp=49.2 sysload=0.25 cputime=141.342 memavail=7407888 print_time=1108.603 buffer_time=2.516 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1084.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15957853 bytes_read=1764591 bytes_retransmit=9 bytes_invalid=0 send_seq=271999 receive_seq=271999 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=39036 freq=400016048 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7252 bytes_read=24364 bytes_retransmit=0 bytes_invalid=0 send_seq=1180 receive_seq=1180 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999147 adj=49996766 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67306 bytes_read=2378678 bytes_retransmit=9 bytes_invalid=0 send_seq=9288 receive_seq=9288 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997395 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16344 bytes_read=135546 bytes_retransmit=9 bytes_invalid=0 send_seq=1923 receive_seq=1923 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997288 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7411 bytes_read=272378 bytes_retransmit=9 bytes_invalid=0 send_seq=1186 receive_seq=1186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997471 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8005 bytes_read=23928 bytes_retransmit=9 bytes_invalid=0 send_seq=1181 receive_seq=1181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999400 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51081 bytes_read=593580 bytes_retransmit=0 bytes_invalid=0 send_seq=4818 receive_seq=4818 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998525 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.8 th1: temp=48.7 th2: temp=51.2 th3: temp=49.2 sysload=0.25 cputime=141.478 memavail=7407888 print_time=1109.141 buffer_time=2.054 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1085.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=15983141 bytes_read=1766982 bytes_retransmit=9 bytes_invalid=0 send_seq=272412 receive_seq=272412 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400016024 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7258 bytes_read=24380 bytes_retransmit=0 bytes_invalid=0 send_seq=1181 receive_seq=1181 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999142 adj=49996750 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67382 bytes_read=2381881 bytes_retransmit=9 bytes_invalid=0 send_seq=9299 receive_seq=9299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997451 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16350 bytes_read=135674 bytes_retransmit=9 bytes_invalid=0 send_seq=1924 receive_seq=1924 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997320 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7417 bytes_read=272672 bytes_retransmit=9 bytes_invalid=0 send_seq=1187 receive_seq=1187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997492 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8011 bytes_read=23944 bytes_retransmit=9 bytes_invalid=0 send_seq=1182 receive_seq=1182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999407 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51087 bytes_read=593936 bytes_retransmit=0 bytes_invalid=0 send_seq=4819 receive_seq=4819 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998567 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.5 th1: temp=49.0 th2: temp=51.1 th3: temp=49.2 sysload=0.25 cputime=141.633 memavail=7406880 print_time=1110.218 buffer_time=2.130 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1086.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16008429 bytes_read=1769386 bytes_retransmit=9 bytes_invalid=0 send_seq=272825 receive_seq=272825 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=41820 freq=400016005 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7264 bytes_read=24409 bytes_retransmit=0 bytes_invalid=0 send_seq=1182 receive_seq=1182 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999137 adj=49996779 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67458 bytes_read=2385012 bytes_retransmit=9 bytes_invalid=0 send_seq=9310 receive_seq=9310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997519 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16356 bytes_read=135774 bytes_retransmit=9 bytes_invalid=0 send_seq=1925 receive_seq=1925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997368 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7423 bytes_read=272906 bytes_retransmit=9 bytes_invalid=0 send_seq=1188 receive_seq=1188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997529 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8017 bytes_read=23971 bytes_retransmit=9 bytes_invalid=0 send_seq=1183 receive_seq=1183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999418 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51093 bytes_read=594292 bytes_retransmit=0 bytes_invalid=0 send_seq=4820 receive_seq=4820 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998591 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.9 th1: temp=48.9 th2: temp=51.2 th3: temp=49.1 sysload=0.31 cputime=141.783 memavail=7406880 print_time=1111.294 buffer_time=2.206 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1087.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16033213 bytes_read=1771721 bytes_retransmit=9 bytes_invalid=0 send_seq=273230 receive_seq=273230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=43676 freq=400015977 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7270 bytes_read=24425 bytes_retransmit=0 bytes_invalid=0 send_seq=1183 receive_seq=1183 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999133 adj=49996830 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67534 bytes_read=2388128 bytes_retransmit=9 bytes_invalid=0 send_seq=9321 receive_seq=9321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997573 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16362 bytes_read=135888 bytes_retransmit=9 bytes_invalid=0 send_seq=1926 receive_seq=1926 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997413 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7429 bytes_read=273140 bytes_retransmit=9 bytes_invalid=0 send_seq=1189 receive_seq=1189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997566 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8023 bytes_read=23987 bytes_retransmit=9 bytes_invalid=0 send_seq=1184 receive_seq=1184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999432 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51099 bytes_read=594648 bytes_retransmit=0 bytes_invalid=0 send_seq=4821 receive_seq=4821 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998640 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.9 th1: temp=49.2 th2: temp=51.1 th3: temp=49.3 sysload=0.31 cputime=141.929 memavail=7406880 print_time=1112.371 buffer_time=2.282 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1088.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16058045 bytes_read=1774061 bytes_retransmit=9 bytes_invalid=0 send_seq=273636 receive_seq=273636 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=45532 freq=400015956 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7276 bytes_read=24441 bytes_retransmit=0 bytes_invalid=0 send_seq=1184 receive_seq=1184 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999129 adj=49996895 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67610 bytes_read=2391270 bytes_retransmit=9 bytes_invalid=0 send_seq=9332 receive_seq=9332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997655 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16368 bytes_read=136016 bytes_retransmit=9 bytes_invalid=0 send_seq=1927 receive_seq=1927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997478 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7435 bytes_read=273434 bytes_retransmit=9 bytes_invalid=0 send_seq=1190 receive_seq=1190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997609 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8029 bytes_read=24003 bytes_retransmit=9 bytes_invalid=0 send_seq=1185 receive_seq=1185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51105 bytes_read=595004 bytes_retransmit=0 bytes_invalid=0 send_seq=4822 receive_seq=4822 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998664 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.9 th1: temp=48.8 th2: temp=51.2 th3: temp=49.2 sysload=0.31 cputime=142.077 memavail=7406880 print_time=1113.447 buffer_time=2.358 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1089.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16082829 bytes_read=1776425 bytes_retransmit=9 bytes_invalid=0 send_seq=274041 receive_seq=274041 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=47388 freq=400015917 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7282 bytes_read=24457 bytes_retransmit=0 bytes_invalid=0 send_seq=1185 receive_seq=1185 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999124 adj=49996922 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67686 bytes_read=2394384 bytes_retransmit=9 bytes_invalid=0 send_seq=9343 receive_seq=9343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997678 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16374 bytes_read=136116 bytes_retransmit=9 bytes_invalid=0 send_seq=1928 receive_seq=1928 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7441 bytes_read=273683 bytes_retransmit=9 bytes_invalid=0 send_seq=1191 receive_seq=1191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8035 bytes_read=24019 bytes_retransmit=9 bytes_invalid=0 send_seq=1186 receive_seq=1186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51111 bytes_read=595360 bytes_retransmit=0 bytes_invalid=0 send_seq=4823 receive_seq=4823 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998694 coil_temp=17.6 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.7 th1: temp=48.9 th2: temp=51.2 th3: temp=49.3 sysload=0.31 cputime=142.224 memavail=7406880 print_time=1114.524 buffer_time=2.435 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 1090.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16107598 bytes_read=1778781 bytes_retransmit=9 bytes_invalid=0 send_seq=274447 receive_seq=274447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=49231 freq=400015895 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7288 bytes_read=24473 bytes_retransmit=0 bytes_invalid=0 send_seq=1186 receive_seq=1186 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999118 adj=49996966 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67762 bytes_read=2397497 bytes_retransmit=9 bytes_invalid=0 send_seq=9354 receive_seq=9354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000183 adj=63997733 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16380 bytes_read=136216 bytes_retransmit=9 bytes_invalid=0 send_seq=1929 receive_seq=1929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7447 bytes_read=273932 bytes_retransmit=9 bytes_invalid=0 send_seq=1192 receive_seq=1192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8041 bytes_read=24035 bytes_retransmit=9 bytes_invalid=0 send_seq=1187 receive_seq=1187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999465 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51117 bytes_read=595716 bytes_retransmit=0 bytes_invalid=0 send_seq=4824 receive_seq=4824 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998721 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.9 th1: temp=49.0 th2: temp=51.2 th3: temp=49.2 sysload=0.31 cputime=142.368 memavail=7406880 print_time=1115.600 buffer_time=2.510 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1091.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16132387 bytes_read=1781121 bytes_retransmit=9 bytes_invalid=0 send_seq=274853 receive_seq=274853 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=38871 freq=400015872 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7294 bytes_read=24502 bytes_retransmit=0 bytes_invalid=0 send_seq=1187 receive_seq=1187 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999113 adj=49996967 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67838 bytes_read=2400655 bytes_retransmit=9 bytes_invalid=0 send_seq=9365 receive_seq=9365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997749 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16386 bytes_read=136344 bytes_retransmit=9 bytes_invalid=0 send_seq=1930 receive_seq=1930 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997562 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7453 bytes_read=274211 bytes_retransmit=9 bytes_invalid=0 send_seq=1193 receive_seq=1193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997682 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8047 bytes_read=24062 bytes_retransmit=9 bytes_invalid=0 send_seq=1188 receive_seq=1188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999465 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51123 bytes_read=596072 bytes_retransmit=0 bytes_invalid=0 send_seq=4825 receive_seq=4825 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998708 coil_temp=17.6 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=50.2 th1: temp=49.1 th2: temp=51.3 th3: temp=49.2 sysload=0.28 cputime=142.504 memavail=7406880 print_time=1116.138 buffer_time=2.048 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1092.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16157480 bytes_read=1783505 bytes_retransmit=9 bytes_invalid=0 send_seq=275262 receive_seq=275262 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400015861 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7300 bytes_read=24518 bytes_retransmit=0 bytes_invalid=0 send_seq=1188 receive_seq=1188 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999108 adj=49996944 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67907 bytes_read=2403744 bytes_retransmit=9 bytes_invalid=0 send_seq=9375 receive_seq=9375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997801 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16392 bytes_read=136458 bytes_retransmit=9 bytes_invalid=0 send_seq=1931 receive_seq=1931 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997593 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7459 bytes_read=274445 bytes_retransmit=9 bytes_invalid=0 send_seq=1194 receive_seq=1194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997705 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8053 bytes_read=24078 bytes_retransmit=9 bytes_invalid=0 send_seq=1189 receive_seq=1189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999473 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51129 bytes_read=596428 bytes_retransmit=0 bytes_invalid=0 send_seq=4826 receive_seq=4826 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998718 coil_temp=17.6 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.9 th1: temp=49.0 th2: temp=51.4 th3: temp=49.3 sysload=0.28 cputime=142.652 memavail=7406880 print_time=1117.215 buffer_time=2.124 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1093.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16182941 bytes_read=1785895 bytes_retransmit=9 bytes_invalid=0 send_seq=275678 receive_seq=275678 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=41686 freq=400015920 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7306 bytes_read=24534 bytes_retransmit=0 bytes_invalid=0 send_seq=1189 receive_seq=1189 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999106 adj=49996929 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67983 bytes_read=2406918 bytes_retransmit=9 bytes_invalid=0 send_seq=9386 receive_seq=9386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997805 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16398 bytes_read=136558 bytes_retransmit=9 bytes_invalid=0 send_seq=1932 receive_seq=1932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997590 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7465 bytes_read=274694 bytes_retransmit=9 bytes_invalid=0 send_seq=1195 receive_seq=1195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997702 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8059 bytes_read=24094 bytes_retransmit=9 bytes_invalid=0 send_seq=1190 receive_seq=1190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999470 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51135 bytes_read=596784 bytes_retransmit=0 bytes_invalid=0 send_seq=4827 receive_seq=4827 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998709 coil_temp=17.7 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.8 th1: temp=49.1 th2: temp=51.0 th3: temp=49.3 sysload=0.28 cputime=142.800 memavail=7406880 print_time=1118.291 buffer_time=2.200 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1094.6: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16207720 bytes_read=1788219 bytes_retransmit=9 bytes_invalid=0 send_seq=276082 receive_seq=276082 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=43542 freq=400015904 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7312 bytes_read=24550 bytes_retransmit=0 bytes_invalid=0 send_seq=1190 receive_seq=1190 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999101 adj=49996850 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68059 bytes_read=2410065 bytes_retransmit=9 bytes_invalid=0 send_seq=9397 receive_seq=9397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997664 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16404 bytes_read=136686 bytes_retransmit=9 bytes_invalid=0 send_seq=1933 receive_seq=1933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997441 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7471 bytes_read=274988 bytes_retransmit=9 bytes_invalid=0 send_seq=1196 receive_seq=1196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997597 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8065 bytes_read=24110 bytes_retransmit=9 bytes_invalid=0 send_seq=1191 receive_seq=1191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51141 bytes_read=597140 bytes_retransmit=0 bytes_invalid=0 send_seq=4828 receive_seq=4828 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998629 coil_temp=17.7 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.9 th1: temp=49.0 th2: temp=51.3 th3: temp=49.2 sysload=0.28 cputime=142.952 memavail=7406940 print_time=1119.368 buffer_time=2.276 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1095.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16232499 bytes_read=1790594 bytes_retransmit=9 bytes_invalid=0 send_seq=276486 receive_seq=276486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=45398 freq=400015898 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7318 bytes_read=24566 bytes_retransmit=0 bytes_invalid=0 send_seq=1191 receive_seq=1191 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999098 adj=49996878 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68135 bytes_read=2413178 bytes_retransmit=9 bytes_invalid=0 send_seq=9408 receive_seq=9408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997709 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16410 bytes_read=136786 bytes_retransmit=9 bytes_invalid=0 send_seq=1934 receive_seq=1934 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997482 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7477 bytes_read=275222 bytes_retransmit=9 bytes_invalid=0 send_seq=1197 receive_seq=1197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8071 bytes_read=24126 bytes_retransmit=9 bytes_invalid=0 send_seq=1192 receive_seq=1192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51147 bytes_read=597496 bytes_retransmit=0 bytes_invalid=0 send_seq=4829 receive_seq=4829 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998645 coil_temp=17.7 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=49.9 th1: temp=48.9 th2: temp=51.2 th3: temp=49.0 sysload=0.28 cputime=143.103 memavail=7405732 print_time=1120.444 buffer_time=2.352 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 1096.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16257283 bytes_read=1792929 bytes_retransmit=9 bytes_invalid=0 send_seq=276891 receive_seq=276891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=47254 freq=400015883 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7324 bytes_read=24595 bytes_retransmit=0 bytes_invalid=0 send_seq=1192 receive_seq=1192 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999093 adj=49996904 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68211 bytes_read=2416309 bytes_retransmit=9 bytes_invalid=0 send_seq=9419 receive_seq=9419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997710 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16416 bytes_read=136886 bytes_retransmit=9 bytes_invalid=0 send_seq=1935 receive_seq=1935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997484 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7483 bytes_read=275471 bytes_retransmit=9 bytes_invalid=0 send_seq=1198 receive_seq=1198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8077 bytes_read=24153 bytes_retransmit=9 bytes_invalid=0 send_seq=1193 receive_seq=1193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51153 bytes_read=597852 bytes_retransmit=0 bytes_invalid=0 send_seq=4830 receive_seq=4830 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998661 coil_temp=17.7 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=49.8 th1: temp=49.2 th2: temp=51.4 th3: temp=49.4 sysload=0.34 cputime=143.262 memavail=7405844 print_time=1121.521 buffer_time=2.428 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 1097.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16282032 bytes_read=1795264 bytes_retransmit=9 bytes_invalid=0 send_seq=277296 receive_seq=277296 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=49132 freq=400015868 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7330 bytes_read=24611 bytes_retransmit=0 bytes_invalid=0 send_seq=1193 receive_seq=1193 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999088 adj=49996914 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68287 bytes_read=2419454 bytes_retransmit=9 bytes_invalid=0 send_seq=9430 receive_seq=9430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997725 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16422 bytes_read=137028 bytes_retransmit=9 bytes_invalid=0 send_seq=1936 receive_seq=1936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7489 bytes_read=275750 bytes_retransmit=9 bytes_invalid=0 send_seq=1199 receive_seq=1199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8083 bytes_read=24169 bytes_retransmit=9 bytes_invalid=0 send_seq=1194 receive_seq=1194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51159 bytes_read=598208 bytes_retransmit=0 bytes_invalid=0 send_seq=4831 receive_seq=4831 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998674 coil_temp=17.7 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=49.9 th1: temp=49.0 th2: temp=51.3 th3: temp=49.3 sysload=0.34 cputime=143.417 memavail=7405852 print_time=1122.597 buffer_time=2.505 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1098.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16306826 bytes_read=1797638 bytes_retransmit=9 bytes_invalid=0 send_seq=277703 receive_seq=277703 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=38772 freq=400015834 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7336 bytes_read=24627 bytes_retransmit=0 bytes_invalid=0 send_seq=1194 receive_seq=1194 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999083 adj=49996915 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68363 bytes_read=2422568 bytes_retransmit=9 bytes_invalid=0 send_seq=9441 receive_seq=9441 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997742 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16428 bytes_read=137128 bytes_retransmit=9 bytes_invalid=0 send_seq=1937 receive_seq=1937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997557 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7495 bytes_read=275984 bytes_retransmit=9 bytes_invalid=0 send_seq=1200 receive_seq=1200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997697 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8089 bytes_read=24185 bytes_retransmit=9 bytes_invalid=0 send_seq=1195 receive_seq=1195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51165 bytes_read=598564 bytes_retransmit=0 bytes_invalid=0 send_seq=4832 receive_seq=4832 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998672 coil_temp=17.7 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=50.1 th1: temp=49.0 th2: temp=51.4 th3: temp=49.3 sysload=0.34 cputime=143.556 memavail=7405852 print_time=1123.135 buffer_time=2.043 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1099.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16331783 bytes_read=1799973 bytes_retransmit=9 bytes_invalid=0 send_seq=278108 receive_seq=278108 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=40461 freq=400015828 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7342 bytes_read=24643 bytes_retransmit=0 bytes_invalid=0 send_seq=1195 receive_seq=1195 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999079 adj=49996910 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68439 bytes_read=2425681 bytes_retransmit=9 bytes_invalid=0 send_seq=9452 receive_seq=9452 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997798 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16434 bytes_read=137228 bytes_retransmit=9 bytes_invalid=0 send_seq=1938 receive_seq=1938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997616 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7501 bytes_read=276248 bytes_retransmit=9 bytes_invalid=0 send_seq=1201 receive_seq=1201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997733 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8095 bytes_read=24201 bytes_retransmit=9 bytes_invalid=0 send_seq=1196 receive_seq=1196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999460 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51171 bytes_read=598920 bytes_retransmit=0 bytes_invalid=0 send_seq=4833 receive_seq=4833 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998693 coil_temp=17.7 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=49.8 th1: temp=49.1 th2: temp=51.4 th3: temp=49.5 sysload=0.34 cputime=143.704 memavail=7405852 print_time=1124.212 buffer_time=2.118 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1100.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16357467 bytes_read=1802394 bytes_retransmit=9 bytes_invalid=0 send_seq=278527 receive_seq=278527 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=41521 freq=400015844 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7348 bytes_read=24659 bytes_retransmit=0 bytes_invalid=0 send_seq=1196 receive_seq=1196 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999075 adj=49996898 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68515 bytes_read=2428823 bytes_retransmit=9 bytes_invalid=0 send_seq=9463 receive_seq=9463 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997796 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16440 bytes_read=137356 bytes_retransmit=9 bytes_invalid=0 send_seq=1939 receive_seq=1939 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997650 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7507 bytes_read=276527 bytes_retransmit=9 bytes_invalid=0 send_seq=1202 receive_seq=1202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997741 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8101 bytes_read=24217 bytes_retransmit=9 bytes_invalid=0 send_seq=1197 receive_seq=1197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51177 bytes_read=599276 bytes_retransmit=0 bytes_invalid=0 send_seq=4834 receive_seq=4834 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998686 coil_temp=17.7 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=49.9 th1: temp=49.2 th2: temp=51.3 th3: temp=49.4 sysload=0.34 cputime=143.855 memavail=7405852 print_time=1125.288 buffer_time=2.194 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1101.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16382177 bytes_read=1804743 bytes_retransmit=9 bytes_invalid=0 send_seq=278929 receive_seq=278929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=43412 freq=400015829 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7354 bytes_read=24688 bytes_retransmit=0 bytes_invalid=0 send_seq=1197 receive_seq=1197 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999070 adj=49996861 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68591 bytes_read=2432013 bytes_retransmit=9 bytes_invalid=0 send_seq=9474 receive_seq=9474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997724 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16446 bytes_read=137456 bytes_retransmit=9 bytes_invalid=0 send_seq=1940 receive_seq=1940 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7513 bytes_read=276761 bytes_retransmit=9 bytes_invalid=0 send_seq=1203 receive_seq=1203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8107 bytes_read=24244 bytes_retransmit=9 bytes_invalid=0 send_seq=1198 receive_seq=1198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51183 bytes_read=599632 bytes_retransmit=0 bytes_invalid=0 send_seq=4835 receive_seq=4835 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998653 coil_temp=17.7 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=50.1 th1: temp=49.3 th2: temp=51.3 th3: temp=49.5 sysload=0.31 cputime=144.000 memavail=7405852 print_time=1126.365 buffer_time=2.270 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1102.6: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16406990 bytes_read=1807109 bytes_retransmit=9 bytes_invalid=0 send_seq=279338 receive_seq=279338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=45233 freq=400015854 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7366 bytes_read=24720 bytes_retransmit=0 bytes_invalid=0 send_seq=1199 receive_seq=1199 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999061 adj=49996883 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68673 bytes_read=2435144 bytes_retransmit=9 bytes_invalid=0 send_seq=9486 receive_seq=9486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997767 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16458 bytes_read=137586 bytes_retransmit=9 bytes_invalid=0 send_seq=1942 receive_seq=1942 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997584 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7525 bytes_read=277026 bytes_retransmit=9 bytes_invalid=0 send_seq=1205 receive_seq=1205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997701 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8119 bytes_read=24276 bytes_retransmit=9 bytes_invalid=0 send_seq=1200 receive_seq=1200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51195 bytes_read=600004 bytes_retransmit=0 bytes_invalid=0 send_seq=4837 receive_seq=4837 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998664 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.9 th1: temp=49.0 th2: temp=51.2 th3: temp=49.4 sysload=0.31 cputime=144.153 memavail=7405852 print_time=1127.441 buffer_time=2.346 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1103.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16431812 bytes_read=1809449 bytes_retransmit=9 bytes_invalid=0 send_seq=279744 receive_seq=279744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=47089 freq=400015825 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7372 bytes_read=24736 bytes_retransmit=0 bytes_invalid=0 send_seq=1200 receive_seq=1200 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999056 adj=49996791 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68749 bytes_read=2438287 bytes_retransmit=9 bytes_invalid=0 send_seq=9497 receive_seq=9497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997684 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16464 bytes_read=137714 bytes_retransmit=9 bytes_invalid=0 send_seq=1943 receive_seq=1943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7531 bytes_read=277305 bytes_retransmit=9 bytes_invalid=0 send_seq=1206 receive_seq=1206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8125 bytes_read=24292 bytes_retransmit=9 bytes_invalid=0 send_seq=1201 receive_seq=1201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51201 bytes_read=600360 bytes_retransmit=0 bytes_invalid=0 send_seq=4838 receive_seq=4838 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998626 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=49.7 th1: temp=49.1 th2: temp=51.3 th3: temp=49.5 sysload=0.31 cputime=144.307 memavail=7405852 print_time=1128.518 buffer_time=2.422 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1104.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16456672 bytes_read=1811816 bytes_retransmit=9 bytes_invalid=0 send_seq=280150 receive_seq=280150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=48871 freq=400015822 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7378 bytes_read=24752 bytes_retransmit=0 bytes_invalid=0 send_seq=1201 receive_seq=1201 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999054 adj=49996836 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68818 bytes_read=2441378 bytes_retransmit=9 bytes_invalid=0 send_seq=9507 receive_seq=9507 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997733 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16470 bytes_read=137814 bytes_retransmit=9 bytes_invalid=0 send_seq=1944 receive_seq=1944 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997566 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7537 bytes_read=277554 bytes_retransmit=9 bytes_invalid=0 send_seq=1207 receive_seq=1207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997682 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8131 bytes_read=24308 bytes_retransmit=9 bytes_invalid=0 send_seq=1202 receive_seq=1202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51207 bytes_read=600716 bytes_retransmit=0 bytes_invalid=0 send_seq=4839 receive_seq=4839 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998656 coil_temp=17.7 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=49.9 th1: temp=49.0 th2: temp=51.5 th3: temp=49.2 sysload=0.31 cputime=144.459 memavail=7405852 print_time=1129.594 buffer_time=2.494 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1105.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16481460 bytes_read=1814160 bytes_retransmit=9 bytes_invalid=0 send_seq=280554 receive_seq=280554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=38505 freq=400015814 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7384 bytes_read=24768 bytes_retransmit=0 bytes_invalid=0 send_seq=1202 receive_seq=1202 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999049 adj=49996860 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68894 bytes_read=2444493 bytes_retransmit=9 bytes_invalid=0 send_seq=9518 receive_seq=9518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997723 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16476 bytes_read=137914 bytes_retransmit=9 bytes_invalid=0 send_seq=1945 receive_seq=1945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997557 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7543 bytes_read=277818 bytes_retransmit=9 bytes_invalid=0 send_seq=1208 receive_seq=1208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997695 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8137 bytes_read=24324 bytes_retransmit=9 bytes_invalid=0 send_seq=1203 receive_seq=1203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51213 bytes_read=601072 bytes_retransmit=0 bytes_invalid=0 send_seq=4840 receive_seq=4840 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998652 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=50.0 th1: temp=49.0 th2: temp=51.3 th3: temp=49.5 sysload=0.31 cputime=144.595 memavail=7405880 print_time=1130.132 buffer_time=2.032 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1106.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16506244 bytes_read=1816495 bytes_retransmit=9 bytes_invalid=0 send_seq=280959 receive_seq=280959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40361 freq=400015803 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7390 bytes_read=24797 bytes_retransmit=0 bytes_invalid=0 send_seq=1203 receive_seq=1203 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999045 adj=49996820 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68970 bytes_read=2447652 bytes_retransmit=9 bytes_invalid=0 send_seq=9529 receive_seq=9529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997749 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16482 bytes_read=138042 bytes_retransmit=9 bytes_invalid=0 send_seq=1946 receive_seq=1946 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7549 bytes_read=278082 bytes_retransmit=9 bytes_invalid=0 send_seq=1209 receive_seq=1209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997724 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8143 bytes_read=24351 bytes_retransmit=9 bytes_invalid=0 send_seq=1204 receive_seq=1204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51219 bytes_read=601428 bytes_retransmit=0 bytes_invalid=0 send_seq=4841 receive_seq=4841 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998656 coil_temp=17.7 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=49.9 th1: temp=49.0 th2: temp=51.3 th3: temp=49.5 sysload=0.29 cputime=144.751 memavail=7405880 print_time=1131.209 buffer_time=2.108 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1107.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16532041 bytes_read=1818944 bytes_retransmit=9 bytes_invalid=0 send_seq=281381 receive_seq=281381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=41289 freq=400015795 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7396 bytes_read=24813 bytes_retransmit=0 bytes_invalid=0 send_seq=1204 receive_seq=1204 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999041 adj=49996815 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69046 bytes_read=2450824 bytes_retransmit=9 bytes_invalid=0 send_seq=9540 receive_seq=9540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997751 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16488 bytes_read=138142 bytes_retransmit=9 bytes_invalid=0 send_seq=1947 receive_seq=1947 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997574 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7555 bytes_read=278316 bytes_retransmit=9 bytes_invalid=0 send_seq=1210 receive_seq=1210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997719 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8149 bytes_read=24367 bytes_retransmit=9 bytes_invalid=0 send_seq=1205 receive_seq=1205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51225 bytes_read=601768 bytes_retransmit=0 bytes_invalid=0 send_seq=4842 receive_seq=4842 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998668 coil_temp=17.7 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=49.9 th1: temp=49.2 th2: temp=51.4 th3: temp=49.5 sysload=0.29 cputime=144.904 memavail=7405880 print_time=1132.285 buffer_time=2.184 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1108.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16556853 bytes_read=1821284 bytes_retransmit=9 bytes_invalid=0 send_seq=281788 receive_seq=281787 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=43145 freq=400015774 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7402 bytes_read=24829 bytes_retransmit=0 bytes_invalid=0 send_seq=1205 receive_seq=1205 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999037 adj=49996842 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69122 bytes_read=2453938 bytes_retransmit=9 bytes_invalid=0 send_seq=9551 receive_seq=9551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997740 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16494 bytes_read=138256 bytes_retransmit=9 bytes_invalid=0 send_seq=1948 receive_seq=1948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997575 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7561 bytes_read=278580 bytes_retransmit=9 bytes_invalid=0 send_seq=1211 receive_seq=1211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997705 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8155 bytes_read=24383 bytes_retransmit=9 bytes_invalid=0 send_seq=1206 receive_seq=1206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51231 bytes_read=602124 bytes_retransmit=0 bytes_invalid=0 send_seq=4843 receive_seq=4843 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998664 coil_temp=17.7 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=50.0 th1: temp=49.0 th2: temp=51.1 th3: temp=49.4 sysload=0.29 cputime=145.057 memavail=7405880 print_time=1133.362 buffer_time=2.260 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1109.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16581583 bytes_read=1823629 bytes_retransmit=9 bytes_invalid=0 send_seq=282194 receive_seq=282194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=45036 freq=400015776 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7408 bytes_read=24845 bytes_retransmit=0 bytes_invalid=0 send_seq=1206 receive_seq=1206 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999034 adj=49996875 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69198 bytes_read=2457080 bytes_retransmit=9 bytes_invalid=0 send_seq=9562 receive_seq=9562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997842 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16500 bytes_read=138384 bytes_retransmit=9 bytes_invalid=0 send_seq=1949 receive_seq=1949 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997588 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7567 bytes_read=278859 bytes_retransmit=9 bytes_invalid=0 send_seq=1212 receive_seq=1212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997730 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8161 bytes_read=24399 bytes_retransmit=9 bytes_invalid=0 send_seq=1207 receive_seq=1207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51237 bytes_read=602480 bytes_retransmit=0 bytes_invalid=0 send_seq=4844 receive_seq=4844 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998677 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=50.2 th1: temp=49.0 th2: temp=51.2 th3: temp=49.7 sysload=0.29 cputime=145.206 memavail=7405880 print_time=1134.438 buffer_time=2.337 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1110.7: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16606418 bytes_read=1826019 bytes_retransmit=9 bytes_invalid=0 send_seq=282601 receive_seq=282601 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=46857 freq=400015760 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7414 bytes_read=24861 bytes_retransmit=0 bytes_invalid=0 send_seq=1207 receive_seq=1207 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999030 adj=49996876 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69274 bytes_read=2460195 bytes_retransmit=9 bytes_invalid=0 send_seq=9573 receive_seq=9573 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997792 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16506 bytes_read=138484 bytes_retransmit=9 bytes_invalid=0 send_seq=1950 receive_seq=1950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997557 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7573 bytes_read=279093 bytes_retransmit=9 bytes_invalid=0 send_seq=1213 receive_seq=1213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997700 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8167 bytes_read=24415 bytes_retransmit=9 bytes_invalid=0 send_seq=1208 receive_seq=1208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999477 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51243 bytes_read=602836 bytes_retransmit=0 bytes_invalid=0 send_seq=4845 receive_seq=4845 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998669 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=50.0 th1: temp=49.2 th2: temp=51.4 th3: temp=49.4 sysload=0.29 cputime=145.378 memavail=7405920 print_time=1135.515 buffer_time=2.413 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1111.7: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16631211 bytes_read=1828364 bytes_retransmit=9 bytes_invalid=0 send_seq=283008 receive_seq=283008 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=48711 freq=400015755 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7420 bytes_read=24890 bytes_retransmit=0 bytes_invalid=0 send_seq=1208 receive_seq=1208 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999026 adj=49996894 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69350 bytes_read=2463325 bytes_retransmit=9 bytes_invalid=0 send_seq=9584 receive_seq=9584 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997786 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16512 bytes_read=138584 bytes_retransmit=9 bytes_invalid=0 send_seq=1951 receive_seq=1951 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997565 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7579 bytes_read=279357 bytes_retransmit=9 bytes_invalid=0 send_seq=1214 receive_seq=1214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997743 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8173 bytes_read=24442 bytes_retransmit=9 bytes_invalid=0 send_seq=1209 receive_seq=1209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999472 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51249 bytes_read=603192 bytes_retransmit=0 bytes_invalid=0 send_seq=4846 receive_seq=4846 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998674 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=49.8 th1: temp=49.2 th2: temp=51.5 th3: temp=49.3 sysload=0.26 cputime=145.536 memavail=7405920 print_time=1136.591 buffer_time=2.489 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1112.7: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16655981 bytes_read=1830704 bytes_retransmit=9 bytes_invalid=0 send_seq=283414 receive_seq=283414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=38340 freq=400015754 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7426 bytes_read=24906 bytes_retransmit=0 bytes_invalid=0 send_seq=1209 receive_seq=1209 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999022 adj=49996893 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69426 bytes_read=2466467 bytes_retransmit=9 bytes_invalid=0 send_seq=9595 receive_seq=9595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997920 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16518 bytes_read=138712 bytes_retransmit=9 bytes_invalid=0 send_seq=1952 receive_seq=1952 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997585 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7585 bytes_read=279621 bytes_retransmit=9 bytes_invalid=0 send_seq=1215 receive_seq=1215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997731 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8179 bytes_read=24458 bytes_retransmit=9 bytes_invalid=0 send_seq=1210 receive_seq=1210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999467 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51255 bytes_read=603548 bytes_retransmit=0 bytes_invalid=0 send_seq=4847 receive_seq=4847 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998677 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=49.4 th1: temp=49.0 th2: temp=51.3 th3: temp=49.5 sysload=0.26 cputime=145.670 memavail=7405924 print_time=1137.129 buffer_time=2.026 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1113.7: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16680740 bytes_read=1833043 bytes_retransmit=9 bytes_invalid=0 send_seq=283814 receive_seq=283814 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=40196 freq=400015747 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7432 bytes_read=24922 bytes_retransmit=0 bytes_invalid=0 send_seq=1210 receive_seq=1210 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999019 adj=49996850 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69502 bytes_read=2469580 bytes_retransmit=9 bytes_invalid=0 send_seq=9606 receive_seq=9606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997901 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16524 bytes_read=138826 bytes_retransmit=9 bytes_invalid=0 send_seq=1953 receive_seq=1953 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997579 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7591 bytes_read=279855 bytes_retransmit=9 bytes_invalid=0 send_seq=1216 receive_seq=1216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997755 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8185 bytes_read=24474 bytes_retransmit=9 bytes_invalid=0 send_seq=1211 receive_seq=1211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999480 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51261 bytes_read=603904 bytes_retransmit=0 bytes_invalid=0 send_seq=4848 receive_seq=4848 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998684 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=49.8 th1: temp=49.1 th2: temp=51.5 th3: temp=49.5 sysload=0.26 cputime=145.833 memavail=7400632 print_time=1138.206 buffer_time=2.101 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1114.7: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16706585 bytes_read=1835468 bytes_retransmit=9 bytes_invalid=0 send_seq=284237 receive_seq=284237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=41124 freq=400015724 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7438 bytes_read=24938 bytes_retransmit=0 bytes_invalid=0 send_seq=1211 receive_seq=1211 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999015 adj=49996845 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69578 bytes_read=2472694 bytes_retransmit=9 bytes_invalid=0 send_seq=9617 receive_seq=9617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997869 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16530 bytes_read=138926 bytes_retransmit=9 bytes_invalid=0 send_seq=1954 receive_seq=1954 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997581 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7597 bytes_read=280134 bytes_retransmit=9 bytes_invalid=0 send_seq=1217 receive_seq=1217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997740 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8191 bytes_read=24490 bytes_retransmit=9 bytes_invalid=0 send_seq=1212 receive_seq=1212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999485 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51267 bytes_read=604260 bytes_retransmit=0 bytes_invalid=0 send_seq=4849 receive_seq=4849 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998687 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=49.8 th1: temp=49.1 th2: temp=51.2 th3: temp=49.5 sysload=0.26 cputime=145.992 memavail=7406644 print_time=1139.282 buffer_time=2.178 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1115.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16731326 bytes_read=1837817 bytes_retransmit=9 bytes_invalid=0 send_seq=284642 receive_seq=284642 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=42980 freq=400015706 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7444 bytes_read=24954 bytes_retransmit=0 bytes_invalid=0 send_seq=1212 receive_seq=1212 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999012 adj=49996887 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69654 bytes_read=2475896 bytes_retransmit=9 bytes_invalid=0 send_seq=9628 receive_seq=9628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997853 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16536 bytes_read=139054 bytes_retransmit=9 bytes_invalid=0 send_seq=1955 receive_seq=1955 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997612 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7603 bytes_read=280398 bytes_retransmit=9 bytes_invalid=0 send_seq=1218 receive_seq=1218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997746 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8197 bytes_read=24506 bytes_retransmit=9 bytes_invalid=0 send_seq=1213 receive_seq=1213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999481 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51273 bytes_read=604616 bytes_retransmit=0 bytes_invalid=0 send_seq=4850 receive_seq=4850 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998700 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=50.0 th1: temp=49.0 th2: temp=51.3 th3: temp=49.3 sysload=0.26 cputime=146.146 memavail=7407140 print_time=1140.359 buffer_time=2.254 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1116.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16756110 bytes_read=1840179 bytes_retransmit=9 bytes_invalid=0 send_seq=285047 receive_seq=285047 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=44836 freq=400015688 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7450 bytes_read=24983 bytes_retransmit=0 bytes_invalid=0 send_seq=1213 receive_seq=1213 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999008 adj=49996910 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69723 bytes_read=2479005 bytes_retransmit=9 bytes_invalid=0 send_seq=9638 receive_seq=9638 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997840 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16542 bytes_read=139154 bytes_retransmit=9 bytes_invalid=0 send_seq=1956 receive_seq=1956 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997615 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7609 bytes_read=280632 bytes_retransmit=9 bytes_invalid=0 send_seq=1219 receive_seq=1219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997740 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8203 bytes_read=24533 bytes_retransmit=9 bytes_invalid=0 send_seq=1214 receive_seq=1214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999475 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51279 bytes_read=604972 bytes_retransmit=0 bytes_invalid=0 send_seq=4851 receive_seq=4851 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998700 coil_temp=17.7 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=50.3 th1: temp=49.1 th2: temp=51.4 th3: temp=49.4 sysload=0.32 cputime=146.297 memavail=7407140 print_time=1141.435 buffer_time=2.329 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1117.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16780942 bytes_read=1842519 bytes_retransmit=9 bytes_invalid=0 send_seq=285453 receive_seq=285453 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=46692 freq=400015714 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7456 bytes_read=24999 bytes_retransmit=0 bytes_invalid=0 send_seq=1214 receive_seq=1214 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999004 adj=49996919 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69799 bytes_read=2482120 bytes_retransmit=9 bytes_invalid=0 send_seq=9649 receive_seq=9649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997824 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16548 bytes_read=139247 bytes_retransmit=9 bytes_invalid=0 send_seq=1957 receive_seq=1957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997643 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7615 bytes_read=280896 bytes_retransmit=9 bytes_invalid=0 send_seq=1220 receive_seq=1220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997738 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8209 bytes_read=24548 bytes_retransmit=9 bytes_invalid=0 send_seq=1215 receive_seq=1215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999475 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51285 bytes_read=605328 bytes_retransmit=0 bytes_invalid=0 send_seq=4852 receive_seq=4852 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998719 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=49.9 th1: temp=49.2 th2: temp=51.2 th3: temp=49.4 sysload=0.32 cputime=146.448 memavail=7407140 print_time=1142.512 buffer_time=2.406 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 1118.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16805726 bytes_read=1844854 bytes_retransmit=9 bytes_invalid=0 send_seq=285858 receive_seq=285858 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=48548 freq=400015708 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7462 bytes_read=25015 bytes_retransmit=0 bytes_invalid=0 send_seq=1215 receive_seq=1215 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999000 adj=49996861 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69875 bytes_read=2485231 bytes_retransmit=9 bytes_invalid=0 send_seq=9660 receive_seq=9660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997813 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16554 bytes_read=139380 bytes_retransmit=9 bytes_invalid=0 send_seq=1958 receive_seq=1958 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997692 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7621 bytes_read=281160 bytes_retransmit=9 bytes_invalid=0 send_seq=1221 receive_seq=1221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8215 bytes_read=24563 bytes_retransmit=9 bytes_invalid=0 send_seq=1216 receive_seq=1216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999463 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51291 bytes_read=605684 bytes_retransmit=0 bytes_invalid=0 send_seq=4853 receive_seq=4853 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998684 coil_temp=17.7 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=50.0 th1: temp=49.1 th2: temp=51.5 th3: temp=49.5 sysload=0.32 cputime=146.595 memavail=7407172 print_time=1143.588 buffer_time=2.482 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1119.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16830485 bytes_read=1847213 bytes_retransmit=9 bytes_invalid=0 send_seq=286262 receive_seq=286262 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=38175 freq=400015691 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7468 bytes_read=25031 bytes_retransmit=0 bytes_invalid=0 send_seq=1216 receive_seq=1216 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998998 adj=49996872 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69951 bytes_read=2488327 bytes_retransmit=9 bytes_invalid=0 send_seq=9671 receive_seq=9671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997793 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16560 bytes_read=139473 bytes_retransmit=9 bytes_invalid=0 send_seq=1959 receive_seq=1959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997686 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7627 bytes_read=281409 bytes_retransmit=9 bytes_invalid=0 send_seq=1222 receive_seq=1222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8221 bytes_read=24578 bytes_retransmit=9 bytes_invalid=0 send_seq=1217 receive_seq=1217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51297 bytes_read=606040 bytes_retransmit=0 bytes_invalid=0 send_seq=4854 receive_seq=4854 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998688 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.0 th1: temp=49.3 th2: temp=51.4 th3: temp=49.6 sysload=0.32 cputime=146.734 memavail=7406920 print_time=1144.126 buffer_time=2.020 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1120.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16855269 bytes_read=1849564 bytes_retransmit=9 bytes_invalid=0 send_seq=286667 receive_seq=286667 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=40031 freq=400015674 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7474 bytes_read=25047 bytes_retransmit=0 bytes_invalid=0 send_seq=1217 receive_seq=1217 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998995 adj=49996864 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70027 bytes_read=2491436 bytes_retransmit=9 bytes_invalid=0 send_seq=9682 receive_seq=9682 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997827 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16566 bytes_read=139566 bytes_retransmit=9 bytes_invalid=0 send_seq=1960 receive_seq=1960 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997702 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7633 bytes_read=281673 bytes_retransmit=9 bytes_invalid=0 send_seq=1223 receive_seq=1223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997698 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8227 bytes_read=24593 bytes_retransmit=9 bytes_invalid=0 send_seq=1218 receive_seq=1218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51303 bytes_read=606396 bytes_retransmit=0 bytes_invalid=0 send_seq=4855 receive_seq=4855 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998698 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.2 th1: temp=49.2 th2: temp=51.5 th3: temp=49.5 sysload=0.32 cputime=146.888 memavail=7406444 print_time=1145.203 buffer_time=2.095 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1121.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16881061 bytes_read=1851979 bytes_retransmit=9 bytes_invalid=0 send_seq=287088 receive_seq=287088 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=40990 freq=400015695 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7480 bytes_read=25076 bytes_retransmit=0 bytes_invalid=0 send_seq=1218 receive_seq=1218 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998992 adj=49996878 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70103 bytes_read=2494575 bytes_retransmit=9 bytes_invalid=0 send_seq=9693 receive_seq=9693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997828 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16572 bytes_read=139692 bytes_retransmit=9 bytes_invalid=0 send_seq=1961 receive_seq=1961 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997702 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7639 bytes_read=281937 bytes_retransmit=9 bytes_invalid=0 send_seq=1224 receive_seq=1224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997710 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8233 bytes_read=24619 bytes_retransmit=9 bytes_invalid=0 send_seq=1219 receive_seq=1219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51309 bytes_read=606752 bytes_retransmit=0 bytes_invalid=0 send_seq=4856 receive_seq=4856 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998720 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.0 th1: temp=49.1 th2: temp=51.5 th3: temp=49.2 sysload=0.30 cputime=147.042 memavail=7406444 print_time=1146.279 buffer_time=2.171 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1122.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16905818 bytes_read=1854333 bytes_retransmit=9 bytes_invalid=0 send_seq=287491 receive_seq=287491 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=42846 freq=400015700 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7486 bytes_read=25092 bytes_retransmit=0 bytes_invalid=0 send_seq=1219 receive_seq=1219 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998989 adj=49996846 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70179 bytes_read=2497691 bytes_retransmit=9 bytes_invalid=0 send_seq=9704 receive_seq=9704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997744 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16578 bytes_read=139792 bytes_retransmit=9 bytes_invalid=0 send_seq=1962 receive_seq=1962 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000034 adj=63997620 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7645 bytes_read=282171 bytes_retransmit=9 bytes_invalid=0 send_seq=1225 receive_seq=1225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997790 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8239 bytes_read=24633 bytes_retransmit=9 bytes_invalid=0 send_seq=1220 receive_seq=1220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51315 bytes_read=607108 bytes_retransmit=0 bytes_invalid=0 send_seq=4857 receive_seq=4857 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998677 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.0 th1: temp=49.3 th2: temp=51.5 th3: temp=49.5 sysload=0.30 cputime=147.194 memavail=7406444 print_time=1147.356 buffer_time=2.247 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1123.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16930639 bytes_read=1856688 bytes_retransmit=9 bytes_invalid=0 send_seq=287900 receive_seq=287900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=44702 freq=400015676 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7492 bytes_read=25108 bytes_retransmit=0 bytes_invalid=0 send_seq=1220 receive_seq=1220 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998986 adj=49996850 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70255 bytes_read=2500877 bytes_retransmit=9 bytes_invalid=0 send_seq=9715 receive_seq=9715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997723 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16584 bytes_read=139920 bytes_retransmit=9 bytes_invalid=0 send_seq=1963 receive_seq=1963 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000033 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7651 bytes_read=282435 bytes_retransmit=9 bytes_invalid=0 send_seq=1226 receive_seq=1226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997745 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8245 bytes_read=24648 bytes_retransmit=9 bytes_invalid=0 send_seq=1221 receive_seq=1221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51321 bytes_read=607464 bytes_retransmit=0 bytes_invalid=0 send_seq=4858 receive_seq=4858 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998665 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.3 th1: temp=49.1 th2: temp=51.3 th3: temp=49.6 sysload=0.30 cputime=147.348 memavail=7406444 print_time=1148.432 buffer_time=2.323 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1124.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16955406 bytes_read=1859023 bytes_retransmit=9 bytes_invalid=0 send_seq=288305 receive_seq=288305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=46558 freq=400015666 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7498 bytes_read=25124 bytes_retransmit=0 bytes_invalid=0 send_seq=1221 receive_seq=1221 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998984 adj=49996890 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70331 bytes_read=2504005 bytes_retransmit=9 bytes_invalid=0 send_seq=9726 receive_seq=9726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997742 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16590 bytes_read=140034 bytes_retransmit=9 bytes_invalid=0 send_seq=1964 receive_seq=1964 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997594 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7657 bytes_read=282714 bytes_retransmit=9 bytes_invalid=0 send_seq=1227 receive_seq=1227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997785 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8251 bytes_read=24663 bytes_retransmit=9 bytes_invalid=0 send_seq=1222 receive_seq=1222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51327 bytes_read=607820 bytes_retransmit=0 bytes_invalid=0 send_seq=4859 receive_seq=4859 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998692 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.0 th1: temp=49.2 th2: temp=51.7 th3: temp=49.7 sysload=0.30 cputime=147.503 memavail=7406444 print_time=1149.509 buffer_time=2.398 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 1125.7: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=16980195 bytes_read=1861408 bytes_retransmit=9 bytes_invalid=0 send_seq=288711 receive_seq=288711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=48414 freq=400015655 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7504 bytes_read=25139 bytes_retransmit=0 bytes_invalid=0 send_seq=1222 receive_seq=1222 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998981 adj=49996904 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70407 bytes_read=2507119 bytes_retransmit=9 bytes_invalid=0 send_seq=9737 receive_seq=9737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997744 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16596 bytes_read=140134 bytes_retransmit=9 bytes_invalid=0 send_seq=1965 receive_seq=1965 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997583 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7663 bytes_read=282948 bytes_retransmit=9 bytes_invalid=0 send_seq=1228 receive_seq=1228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997759 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8257 bytes_read=24678 bytes_retransmit=9 bytes_invalid=0 send_seq=1223 receive_seq=1223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51333 bytes_read=608176 bytes_retransmit=0 bytes_invalid=0 send_seq=4860 receive_seq=4860 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998691 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.2 th1: temp=49.2 th2: temp=51.5 th3: temp=49.5 sysload=0.30 cputime=147.650 memavail=7406252 print_time=1150.585 buffer_time=2.474 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1126.7: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17005064 bytes_read=1863744 bytes_retransmit=9 bytes_invalid=0 send_seq=289117 receive_seq=289117 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=37974 freq=400015655 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7510 bytes_read=25167 bytes_retransmit=0 bytes_invalid=0 send_seq=1223 receive_seq=1223 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998979 adj=49996916 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70483 bytes_read=2510263 bytes_retransmit=9 bytes_invalid=0 send_seq=9748 receive_seq=9748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997739 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16602 bytes_read=140248 bytes_retransmit=9 bytes_invalid=0 send_seq=1966 receive_seq=1966 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997580 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7669 bytes_read=283227 bytes_retransmit=9 bytes_invalid=0 send_seq=1229 receive_seq=1229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997769 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8263 bytes_read=24704 bytes_retransmit=9 bytes_invalid=0 send_seq=1224 receive_seq=1224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51339 bytes_read=608532 bytes_retransmit=0 bytes_invalid=0 send_seq=4861 receive_seq=4861 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998690 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.1 th1: temp=49.2 th2: temp=51.7 th3: temp=49.5 sysload=0.27 cputime=147.787 memavail=7406252 print_time=1151.123 buffer_time=2.011 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1127.7: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17029843 bytes_read=1866069 bytes_retransmit=9 bytes_invalid=0 send_seq=289521 receive_seq=289520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=39799 freq=400015682 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7516 bytes_read=25182 bytes_retransmit=0 bytes_invalid=0 send_seq=1224 receive_seq=1224 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998976 adj=49996889 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70552 bytes_read=2513369 bytes_retransmit=9 bytes_invalid=0 send_seq=9758 receive_seq=9758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997723 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16608 bytes_read=140362 bytes_retransmit=9 bytes_invalid=0 send_seq=1967 receive_seq=1967 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997565 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7675 bytes_read=283476 bytes_retransmit=9 bytes_invalid=0 send_seq=1230 receive_seq=1230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997757 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8269 bytes_read=24719 bytes_retransmit=9 bytes_invalid=0 send_seq=1225 receive_seq=1225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51345 bytes_read=608888 bytes_retransmit=0 bytes_invalid=0 send_seq=4862 receive_seq=4862 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998685 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.2 th1: temp=49.7 th2: temp=51.5 th3: temp=49.5 sysload=0.27 cputime=147.934 memavail=7406252 print_time=1152.200 buffer_time=2.087 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1128.7: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17055542 bytes_read=1868483 bytes_retransmit=9 bytes_invalid=0 send_seq=289935 receive_seq=289935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=40795 freq=400015668 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7522 bytes_read=25197 bytes_retransmit=0 bytes_invalid=0 send_seq=1225 receive_seq=1225 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998975 adj=49996831 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70628 bytes_read=2516482 bytes_retransmit=9 bytes_invalid=0 send_seq=9769 receive_seq=9769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997655 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16614 bytes_read=140476 bytes_retransmit=9 bytes_invalid=0 send_seq=1968 receive_seq=1968 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7681 bytes_read=283710 bytes_retransmit=9 bytes_invalid=0 send_seq=1231 receive_seq=1231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997741 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8275 bytes_read=24734 bytes_retransmit=9 bytes_invalid=0 send_seq=1226 receive_seq=1226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51351 bytes_read=609244 bytes_retransmit=0 bytes_invalid=0 send_seq=4863 receive_seq=4863 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998660 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.2 th1: temp=49.2 th2: temp=51.7 th3: temp=49.5 sysload=0.27 cputime=148.089 memavail=7405252 print_time=1153.276 buffer_time=2.163 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1129.7: gcodein=0  mcu: mcu_awake=0.020 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17080336 bytes_read=1870828 bytes_retransmit=9 bytes_invalid=0 send_seq=290342 receive_seq=290342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=42651 freq=400015683 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7528 bytes_read=25212 bytes_retransmit=0 bytes_invalid=0 send_seq=1226 receive_seq=1226 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998972 adj=49996873 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70704 bytes_read=2519609 bytes_retransmit=9 bytes_invalid=0 send_seq=9780 receive_seq=9780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997768 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16620 bytes_read=140590 bytes_retransmit=9 bytes_invalid=0 send_seq=1969 receive_seq=1969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997526 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7687 bytes_read=284004 bytes_retransmit=9 bytes_invalid=0 send_seq=1232 receive_seq=1232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997731 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8281 bytes_read=24749 bytes_retransmit=9 bytes_invalid=0 send_seq=1227 receive_seq=1227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51357 bytes_read=609600 bytes_retransmit=0 bytes_invalid=0 send_seq=4864 receive_seq=4864 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998693 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.1 th1: temp=49.1 th2: temp=51.4 th3: temp=49.6 sysload=0.27 cputime=148.244 memavail=7405260 print_time=1154.353 buffer_time=2.239 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1130.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17105148 bytes_read=1873189 bytes_retransmit=9 bytes_invalid=0 send_seq=290749 receive_seq=290749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=44507 freq=400015689 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7534 bytes_read=25228 bytes_retransmit=0 bytes_invalid=0 send_seq=1227 receive_seq=1227 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998969 adj=49996857 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70780 bytes_read=2522796 bytes_retransmit=9 bytes_invalid=0 send_seq=9791 receive_seq=9791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997717 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16626 bytes_read=140704 bytes_retransmit=9 bytes_invalid=0 send_seq=1970 receive_seq=1970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7693 bytes_read=284253 bytes_retransmit=9 bytes_invalid=0 send_seq=1233 receive_seq=1233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8287 bytes_read=24764 bytes_retransmit=9 bytes_invalid=0 send_seq=1228 receive_seq=1228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999439 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51363 bytes_read=609956 bytes_retransmit=0 bytes_invalid=0 send_seq=4865 receive_seq=4865 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998671 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.1 th1: temp=49.3 th2: temp=51.5 th3: temp=49.5 sysload=0.27 cputime=148.404 memavail=7400224 print_time=1155.429 buffer_time=2.316 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1131.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17129897 bytes_read=1875518 bytes_retransmit=9 bytes_invalid=0 send_seq=291147 receive_seq=291147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=46363 freq=400015669 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7540 bytes_read=25257 bytes_retransmit=0 bytes_invalid=0 send_seq=1228 receive_seq=1228 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998967 adj=49996843 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70856 bytes_read=2525928 bytes_retransmit=9 bytes_invalid=0 send_seq=9802 receive_seq=9802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997766 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16632 bytes_read=140804 bytes_retransmit=9 bytes_invalid=0 send_seq=1971 receive_seq=1971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997474 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7699 bytes_read=284487 bytes_retransmit=9 bytes_invalid=0 send_seq=1234 receive_seq=1234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8293 bytes_read=24790 bytes_retransmit=9 bytes_invalid=0 send_seq=1229 receive_seq=1229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51369 bytes_read=610312 bytes_retransmit=0 bytes_invalid=0 send_seq=4866 receive_seq=4866 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998660 coil_temp=17.7 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=50.1 th1: temp=49.1 th2: temp=51.5 th3: temp=49.5 sysload=0.25 cputime=148.560 memavail=7405748 print_time=1156.506 buffer_time=2.392 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 1132.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17154668 bytes_read=1877858 bytes_retransmit=9 bytes_invalid=0 send_seq=291553 receive_seq=291553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=48219 freq=400015654 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7546 bytes_read=25273 bytes_retransmit=0 bytes_invalid=0 send_seq=1229 receive_seq=1229 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998966 adj=49996884 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70932 bytes_read=2529057 bytes_retransmit=9 bytes_invalid=0 send_seq=9813 receive_seq=9813 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997858 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16638 bytes_read=140918 bytes_retransmit=9 bytes_invalid=0 send_seq=1972 receive_seq=1972 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7705 bytes_read=284766 bytes_retransmit=9 bytes_invalid=0 send_seq=1235 receive_seq=1235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8299 bytes_read=24805 bytes_retransmit=9 bytes_invalid=0 send_seq=1230 receive_seq=1230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51375 bytes_read=610668 bytes_retransmit=0 bytes_invalid=0 send_seq=4867 receive_seq=4867 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998696 coil_temp=17.7 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=50.2 th1: temp=49.4 th2: temp=52.0 th3: temp=49.6 sysload=0.25 cputime=148.706 memavail=7405880 print_time=1157.582 buffer_time=2.467 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1133.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17179475 bytes_read=1880193 bytes_retransmit=9 bytes_invalid=0 send_seq=291958 receive_seq=291958 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=37844 freq=400015683 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7552 bytes_read=25289 bytes_retransmit=0 bytes_invalid=0 send_seq=1230 receive_seq=1230 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998964 adj=49996920 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71008 bytes_read=2532188 bytes_retransmit=9 bytes_invalid=0 send_seq=9824 receive_seq=9824 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997908 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16644 bytes_read=141046 bytes_retransmit=9 bytes_invalid=0 send_seq=1973 receive_seq=1973 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997552 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7711 bytes_read=285015 bytes_retransmit=9 bytes_invalid=0 send_seq=1236 receive_seq=1236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997693 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8305 bytes_read=24820 bytes_retransmit=9 bytes_invalid=0 send_seq=1231 receive_seq=1231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999467 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51381 bytes_read=611024 bytes_retransmit=0 bytes_invalid=0 send_seq=4868 receive_seq=4868 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998693 coil_temp=17.7 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=50.1 th1: temp=49.2 th2: temp=51.7 th3: temp=49.5 sysload=0.25 cputime=148.840 memavail=7405880 print_time=1158.120 buffer_time=2.005 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1134.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17204321 bytes_read=1882562 bytes_retransmit=9 bytes_invalid=0 send_seq=292364 receive_seq=292364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=39665 freq=400015688 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7558 bytes_read=25305 bytes_retransmit=0 bytes_invalid=0 send_seq=1231 receive_seq=1231 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998963 adj=49996854 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71084 bytes_read=2535304 bytes_retransmit=9 bytes_invalid=0 send_seq=9835 receive_seq=9835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997828 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16650 bytes_read=141146 bytes_retransmit=9 bytes_invalid=0 send_seq=1974 receive_seq=1974 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997487 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7717 bytes_read=285264 bytes_retransmit=9 bytes_invalid=0 send_seq=1237 receive_seq=1237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8311 bytes_read=24835 bytes_retransmit=9 bytes_invalid=0 send_seq=1232 receive_seq=1232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999458 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51387 bytes_read=611380 bytes_retransmit=0 bytes_invalid=0 send_seq=4869 receive_seq=4869 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998664 coil_temp=17.7 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=50.2 th1: temp=49.4 th2: temp=51.6 th3: temp=49.6 sysload=0.25 cputime=148.988 memavail=7404124 print_time=1159.197 buffer_time=2.080 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1135.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17230108 bytes_read=1884983 bytes_retransmit=9 bytes_invalid=0 send_seq=292784 receive_seq=292783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40593 freq=400015687 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7564 bytes_read=25321 bytes_retransmit=0 bytes_invalid=0 send_seq=1232 receive_seq=1232 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998963 adj=49996856 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71160 bytes_read=2538432 bytes_retransmit=9 bytes_invalid=0 send_seq=9846 receive_seq=9846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63998028 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16656 bytes_read=141260 bytes_retransmit=9 bytes_invalid=0 send_seq=1975 receive_seq=1975 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997471 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7723 bytes_read=285543 bytes_retransmit=9 bytes_invalid=0 send_seq=1238 receive_seq=1238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8317 bytes_read=24850 bytes_retransmit=9 bytes_invalid=0 send_seq=1233 receive_seq=1233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51393 bytes_read=611736 bytes_retransmit=0 bytes_invalid=0 send_seq=4870 receive_seq=4870 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998668 coil_temp=17.7 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=49.9 th1: temp=49.1 th2: temp=51.5 th3: temp=49.5 sysload=0.25 cputime=149.141 memavail=7404124 print_time=1160.273 buffer_time=2.156 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1136.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17254835 bytes_read=1887323 bytes_retransmit=9 bytes_invalid=0 send_seq=293189 receive_seq=293189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=42484 freq=400015696 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7570 bytes_read=25350 bytes_retransmit=0 bytes_invalid=0 send_seq=1233 receive_seq=1233 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998959 adj=49996881 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71236 bytes_read=2541576 bytes_retransmit=9 bytes_invalid=0 send_seq=9857 receive_seq=9857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997915 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16662 bytes_read=141374 bytes_retransmit=9 bytes_invalid=0 send_seq=1976 receive_seq=1976 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7729 bytes_read=285792 bytes_retransmit=9 bytes_invalid=0 send_seq=1239 receive_seq=1239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997621 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8323 bytes_read=24876 bytes_retransmit=9 bytes_invalid=0 send_seq=1234 receive_seq=1234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51399 bytes_read=612092 bytes_retransmit=0 bytes_invalid=0 send_seq=4871 receive_seq=4871 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998661 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.2 th1: temp=49.3 th2: temp=51.5 th3: temp=49.5 sysload=0.31 cputime=149.294 memavail=7404124 print_time=1161.350 buffer_time=2.232 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1137.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17279681 bytes_read=1889687 bytes_retransmit=9 bytes_invalid=0 send_seq=293595 receive_seq=293595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=44305 freq=400015696 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7576 bytes_read=25366 bytes_retransmit=0 bytes_invalid=0 send_seq=1234 receive_seq=1234 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998957 adj=49996854 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71312 bytes_read=2544748 bytes_retransmit=9 bytes_invalid=0 send_seq=9868 receive_seq=9868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997814 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16668 bytes_read=141474 bytes_retransmit=9 bytes_invalid=0 send_seq=1977 receive_seq=1977 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997463 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7735 bytes_read=286026 bytes_retransmit=9 bytes_invalid=0 send_seq=1240 receive_seq=1240 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997606 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8329 bytes_read=24891 bytes_retransmit=9 bytes_invalid=0 send_seq=1235 receive_seq=1235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51405 bytes_read=612448 bytes_retransmit=0 bytes_invalid=0 send_seq=4872 receive_seq=4872 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998664 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.2 th1: temp=49.4 th2: temp=51.7 th3: temp=49.5 sysload=0.31 cputime=149.441 memavail=7404124 print_time=1162.426 buffer_time=2.307 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1138.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17304488 bytes_read=1892027 bytes_retransmit=9 bytes_invalid=0 send_seq=294001 receive_seq=294001 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=46161 freq=400015742 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7582 bytes_read=25382 bytes_retransmit=0 bytes_invalid=0 send_seq=1235 receive_seq=1235 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998956 adj=49996867 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71388 bytes_read=2547877 bytes_retransmit=9 bytes_invalid=0 send_seq=9879 receive_seq=9879 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997757 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16674 bytes_read=141602 bytes_retransmit=9 bytes_invalid=0 send_seq=1978 receive_seq=1978 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997484 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7741 bytes_read=286305 bytes_retransmit=9 bytes_invalid=0 send_seq=1241 receive_seq=1241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997616 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8335 bytes_read=24906 bytes_retransmit=9 bytes_invalid=0 send_seq=1236 receive_seq=1236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51411 bytes_read=612804 bytes_retransmit=0 bytes_invalid=0 send_seq=4873 receive_seq=4873 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998717 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.0 th1: temp=49.5 th2: temp=51.5 th3: temp=49.6 sysload=0.31 cputime=149.591 memavail=7404124 print_time=1163.503 buffer_time=2.383 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 1139.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17329237 bytes_read=1894327 bytes_retransmit=9 bytes_invalid=0 send_seq=294399 receive_seq=294399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=48017 freq=400015850 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7588 bytes_read=25398 bytes_retransmit=0 bytes_invalid=0 send_seq=1236 receive_seq=1236 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998954 adj=49996811 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71457 bytes_read=2550981 bytes_retransmit=9 bytes_invalid=0 send_seq=9889 receive_seq=9889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997638 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16680 bytes_read=141716 bytes_retransmit=9 bytes_invalid=0 send_seq=1979 receive_seq=1979 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997398 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7747 bytes_read=286556 bytes_retransmit=9 bytes_invalid=0 send_seq=1242 receive_seq=1242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997556 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8341 bytes_read=24921 bytes_retransmit=9 bytes_invalid=0 send_seq=1237 receive_seq=1237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999426 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51417 bytes_read=613160 bytes_retransmit=0 bytes_invalid=0 send_seq=4874 receive_seq=4874 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998712 coil_temp=17.7 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=50.2 th1: temp=49.3 th2: temp=51.3 th3: temp=49.7 sysload=0.31 cputime=149.736 memavail=7404124 print_time=1164.579 buffer_time=2.459 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 1140.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17354299 bytes_read=1896732 bytes_retransmit=9 bytes_invalid=0 send_seq=294809 receive_seq=294809 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=49596 freq=400015828 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7594 bytes_read=25414 bytes_retransmit=0 bytes_invalid=0 send_seq=1237 receive_seq=1237 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998952 adj=49996676 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71533 bytes_read=2554154 bytes_retransmit=9 bytes_invalid=0 send_seq=9900 receive_seq=9900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997436 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16686 bytes_read=141816 bytes_retransmit=9 bytes_invalid=0 send_seq=1980 receive_seq=1980 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997229 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7753 bytes_read=286770 bytes_retransmit=9 bytes_invalid=0 send_seq=1243 receive_seq=1243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997424 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8347 bytes_read=24937 bytes_retransmit=9 bytes_invalid=0 send_seq=1238 receive_seq=1238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999395 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51423 bytes_read=613516 bytes_retransmit=0 bytes_invalid=0 send_seq=4875 receive_seq=4875 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998600 coil_temp=17.7 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=50.1 th1: temp=49.4 th2: temp=51.6 th3: temp=49.6 sysload=0.31 cputime=149.887 memavail=7404124 print_time=1165.656 buffer_time=2.524 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1141.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17379172 bytes_read=1899097 bytes_retransmit=9 bytes_invalid=0 send_seq=295220 receive_seq=295220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=39201 freq=400015819 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7600 bytes_read=25443 bytes_retransmit=0 bytes_invalid=0 send_seq=1238 receive_seq=1238 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998950 adj=49996745 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71609 bytes_read=2557313 bytes_retransmit=9 bytes_invalid=0 send_seq=9911 receive_seq=9911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997491 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16692 bytes_read=141944 bytes_retransmit=9 bytes_invalid=0 send_seq=1981 receive_seq=1981 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997323 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7759 bytes_read=287044 bytes_retransmit=9 bytes_invalid=0 send_seq=1244 receive_seq=1244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997498 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8353 bytes_read=24964 bytes_retransmit=9 bytes_invalid=0 send_seq=1239 receive_seq=1239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999408 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51429 bytes_read=613872 bytes_retransmit=0 bytes_invalid=0 send_seq=4876 receive_seq=4876 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998617 coil_temp=17.7 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=50.1 th1: temp=49.5 th2: temp=51.7 th3: temp=49.3 sysload=0.29 cputime=150.025 memavail=7404124 print_time=1166.194 buffer_time=2.061 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1142.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17404579 bytes_read=1901477 bytes_retransmit=9 bytes_invalid=0 send_seq=295634 receive_seq=295634 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400015809 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7606 bytes_read=25459 bytes_retransmit=0 bytes_invalid=0 send_seq=1239 receive_seq=1239 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998947 adj=49996733 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71685 bytes_read=2560426 bytes_retransmit=9 bytes_invalid=0 send_seq=9922 receive_seq=9922 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997477 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16698 bytes_read=142044 bytes_retransmit=9 bytes_invalid=0 send_seq=1982 receive_seq=1982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997327 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7765 bytes_read=287262 bytes_retransmit=9 bytes_invalid=0 send_seq=1245 receive_seq=1245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997504 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8359 bytes_read=24980 bytes_retransmit=9 bytes_invalid=0 send_seq=1240 receive_seq=1240 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999409 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51435 bytes_read=614228 bytes_retransmit=0 bytes_invalid=0 send_seq=4877 receive_seq=4877 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998634 coil_temp=17.7 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=50.2 th1: temp=49.5 th2: temp=51.5 th3: temp=49.7 sysload=0.29 cputime=150.173 memavail=7404124 print_time=1167.270 buffer_time=2.138 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1143.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17429674 bytes_read=1903861 bytes_retransmit=9 bytes_invalid=0 send_seq=296043 receive_seq=296043 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=42020 freq=400015805 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7612 bytes_read=25475 bytes_retransmit=0 bytes_invalid=0 send_seq=1240 receive_seq=1240 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998945 adj=49996747 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71761 bytes_read=2563542 bytes_retransmit=9 bytes_invalid=0 send_seq=9933 receive_seq=9933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997497 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16704 bytes_read=142158 bytes_retransmit=9 bytes_invalid=0 send_seq=1983 receive_seq=1983 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997356 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7771 bytes_read=287480 bytes_retransmit=9 bytes_invalid=0 send_seq=1246 receive_seq=1246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997541 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8365 bytes_read=24996 bytes_retransmit=9 bytes_invalid=0 send_seq=1241 receive_seq=1241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999416 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51441 bytes_read=614584 bytes_retransmit=0 bytes_invalid=0 send_seq=4878 receive_seq=4878 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998634 coil_temp=17.7 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=50.1 th1: temp=49.3 th2: temp=51.5 th3: temp=49.6 sysload=0.29 cputime=150.322 memavail=7404140 print_time=1168.347 buffer_time=2.214 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1144.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17454458 bytes_read=1906196 bytes_retransmit=9 bytes_invalid=0 send_seq=296448 receive_seq=296448 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=43876 freq=400015785 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7618 bytes_read=25491 bytes_retransmit=0 bytes_invalid=0 send_seq=1241 receive_seq=1241 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998944 adj=49996773 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71837 bytes_read=2566684 bytes_retransmit=9 bytes_invalid=0 send_seq=9944 receive_seq=9944 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997520 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16710 bytes_read=142286 bytes_retransmit=9 bytes_invalid=0 send_seq=1984 receive_seq=1984 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997385 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7777 bytes_read=287777 bytes_retransmit=9 bytes_invalid=0 send_seq=1247 receive_seq=1247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997566 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8371 bytes_read=25012 bytes_retransmit=9 bytes_invalid=0 send_seq=1242 receive_seq=1242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999423 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51447 bytes_read=614940 bytes_retransmit=0 bytes_invalid=0 send_seq=4879 receive_seq=4879 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998707 coil_temp=17.7 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=50.3 th1: temp=49.4 th2: temp=51.8 th3: temp=49.7 sysload=0.29 cputime=150.473 memavail=7404160 print_time=1169.423 buffer_time=2.290 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1145.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17479196 bytes_read=1908517 bytes_retransmit=9 bytes_invalid=0 send_seq=296847 receive_seq=296847 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=45764 freq=400015773 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7624 bytes_read=25507 bytes_retransmit=0 bytes_invalid=0 send_seq=1242 receive_seq=1242 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998950 adj=49996834 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71913 bytes_read=2569797 bytes_retransmit=9 bytes_invalid=0 send_seq=9955 receive_seq=9955 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997583 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16716 bytes_read=142386 bytes_retransmit=9 bytes_invalid=0 send_seq=1985 receive_seq=1985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997438 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7783 bytes_read=288011 bytes_retransmit=9 bytes_invalid=0 send_seq=1248 receive_seq=1248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997602 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8377 bytes_read=25028 bytes_retransmit=9 bytes_invalid=0 send_seq=1243 receive_seq=1243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999432 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51453 bytes_read=615296 bytes_retransmit=0 bytes_invalid=0 send_seq=4880 receive_seq=4880 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998700 coil_temp=17.7 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=50.2 th1: temp=49.3 th2: temp=51.7 th3: temp=49.7 sysload=0.29 cputime=150.623 memavail=7403944 print_time=1170.500 buffer_time=2.366 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 1146.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17503932 bytes_read=1910876 bytes_retransmit=9 bytes_invalid=0 send_seq=297251 receive_seq=297251 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=47620 freq=400015772 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7630 bytes_read=25536 bytes_retransmit=0 bytes_invalid=0 send_seq=1243 receive_seq=1243 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998948 adj=49996954 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71989 bytes_read=2572927 bytes_retransmit=9 bytes_invalid=0 send_seq=9966 receive_seq=9966 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997607 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16722 bytes_read=142486 bytes_retransmit=9 bytes_invalid=0 send_seq=1986 receive_seq=1986 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997475 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7789 bytes_read=288245 bytes_retransmit=9 bytes_invalid=0 send_seq=1249 receive_seq=1249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8383 bytes_read=25055 bytes_retransmit=9 bytes_invalid=0 send_seq=1244 receive_seq=1244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51459 bytes_read=615652 bytes_retransmit=0 bytes_invalid=0 send_seq=4881 receive_seq=4881 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998693 coil_temp=17.7 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=50.1 th1: temp=49.4 th2: temp=51.6 th3: temp=49.7 sysload=0.26 cputime=150.768 memavail=7403944 print_time=1171.576 buffer_time=2.442 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Stats 1147.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17528791 bytes_read=1913204 bytes_retransmit=9 bytes_invalid=0 send_seq=297655 receive_seq=297655 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=49429 freq=400015776 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7636 bytes_read=25552 bytes_retransmit=0 bytes_invalid=0 send_seq=1244 receive_seq=1244 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998947 adj=49996938 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=72065 bytes_read=2576068 bytes_retransmit=9 bytes_invalid=0 send_seq=9977 receive_seq=9977 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997603 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16728 bytes_read=142614 bytes_retransmit=9 bytes_invalid=0 send_seq=1987 receive_seq=1987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997483 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7795 bytes_read=288539 bytes_retransmit=9 bytes_invalid=0 send_seq=1250 receive_seq=1250 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8389 bytes_read=25071 bytes_retransmit=9 bytes_invalid=0 send_seq=1245 receive_seq=1245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51465 bytes_read=616008 bytes_retransmit=0 bytes_invalid=0 send_seq=4882 receive_seq=4882 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998684 coil_temp=17.7 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=50.2 th1: temp=49.5 th2: temp=51.5 th3: temp=49.6 sysload=0.26 cputime=150.917 memavail=7403944 print_time=1172.653 buffer_time=2.518 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1148.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17553508 bytes_read=1915524 bytes_retransmit=9 bytes_invalid=0 send_seq=298058 receive_seq=298058 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=39103 freq=400015763 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7642 bytes_read=25568 bytes_retransmit=0 bytes_invalid=0 send_seq=1245 receive_seq=1245 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998947 adj=49996928 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=72141 bytes_read=2579241 bytes_retransmit=9 bytes_invalid=0 send_seq=9988 receive_seq=9988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997596 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16734 bytes_read=142728 bytes_retransmit=9 bytes_invalid=0 send_seq=1988 receive_seq=1988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997482 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7801 bytes_read=288773 bytes_retransmit=9 bytes_invalid=0 send_seq=1251 receive_seq=1251 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8395 bytes_read=25087 bytes_retransmit=9 bytes_invalid=0 send_seq=1246 receive_seq=1246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51471 bytes_read=616364 bytes_retransmit=0 bytes_invalid=0 send_seq=4883 receive_seq=4883 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998659 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.1 th1: temp=49.6 th2: temp=51.7 th3: temp=49.7 sysload=0.26 cputime=151.064 memavail=7405468 print_time=1173.191 buffer_time=2.055 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
Generating oscillations at (125.000, 250.000, 20.005)
toolhead: max_velocity: 800.000000
max_accel: 3945.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance generation
Testing frequency 53 Hz
Stats 1149.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17578863 bytes_read=1917938 bytes_retransmit=9 bytes_invalid=0 send_seq=298473 receive_seq=298473 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=40461 freq=400015749 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7648 bytes_read=25584 bytes_retransmit=0 bytes_invalid=0 send_seq=1246 receive_seq=1246 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998946 adj=49996941 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=72217 bytes_read=2582355 bytes_retransmit=9 bytes_invalid=0 send_seq=9999 receive_seq=9999 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997601 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16740 bytes_read=142828 bytes_retransmit=9 bytes_invalid=0 send_seq=1989 receive_seq=1989 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7807 bytes_read=289022 bytes_retransmit=9 bytes_invalid=0 send_seq=1252 receive_seq=1252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8401 bytes_read=25103 bytes_retransmit=9 bytes_invalid=0 send_seq=1247 receive_seq=1247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51477 bytes_read=616720 bytes_retransmit=0 bytes_invalid=0 send_seq=4884 receive_seq=4884 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998662 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.2 th1: temp=49.4 th2: temp=51.6 th3: temp=49.7 sysload=0.26 cputime=151.213 memavail=7405600 print_time=1174.267 buffer_time=2.131 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Completed resonance generation for y axis
webhooks client 4132488288: Disconnected
LIS2DW finished 'toolboard_t0' measurements
Stats 1150.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17604156 bytes_read=1920334 bytes_retransmit=9 bytes_invalid=0 send_seq=298887 receive_seq=298887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=29604 freq=400015746 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7654 bytes_read=25600 bytes_retransmit=0 bytes_invalid=0 send_seq=1247 receive_seq=1247 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998945 adj=49996963 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=72292 bytes_read=2583367 bytes_retransmit=9 bytes_invalid=0 send_seq=10008 receive_seq=10008 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997629 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16746 bytes_read=142956 bytes_retransmit=9 bytes_invalid=0 send_seq=1990 receive_seq=1990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997521 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7813 bytes_read=289316 bytes_retransmit=9 bytes_invalid=0 send_seq=1253 receive_seq=1253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8407 bytes_read=25119 bytes_retransmit=9 bytes_invalid=0 send_seq=1248 receive_seq=1248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51483 bytes_read=617076 bytes_retransmit=0 bytes_invalid=0 send_seq=4885 receive_seq=4885 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998663 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.3 th1: temp=49.3 th2: temp=51.8 th3: temp=49.9 sysload=0.26 cputime=151.326 memavail=7405356 print_time=1174.806 buffer_time=1.669 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 1151.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17628993 bytes_read=1922674 bytes_retransmit=9 bytes_invalid=0 send_seq=299294 receive_seq=299293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=7028 freq=400015746 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7660 bytes_read=25616 bytes_retransmit=0 bytes_invalid=0 send_seq=1248 receive_seq=1248 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998944 adj=49996947 toolboard_t0: mcu_awake=0.232 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=72298 bytes_read=2583484 bytes_retransmit=9 bytes_invalid=0 send_seq=10009 receive_seq=10009 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997830 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16752 bytes_read=143056 bytes_retransmit=9 bytes_invalid=0 send_seq=1991 receive_seq=1991 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997525 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7819 bytes_read=289550 bytes_retransmit=9 bytes_invalid=0 send_seq=1254 receive_seq=1254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8413 bytes_read=25146 bytes_retransmit=9 bytes_invalid=0 send_seq=1249 receive_seq=1249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51489 bytes_read=617432 bytes_retransmit=0 bytes_invalid=0 send_seq=4886 receive_seq=4886 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998648 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.4 th1: temp=49.4 th2: temp=51.9 th3: temp=49.8 sysload=0.24 cputime=151.408 memavail=7405356 print_time=1174.806 buffer_time=0.668 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1152.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17636932 bytes_read=1923738 bytes_retransmit=9 bytes_invalid=0 send_seq=299438 receive_seq=299438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015774 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7666 bytes_read=25645 bytes_retransmit=0 bytes_invalid=0 send_seq=1249 receive_seq=1249 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998942 adj=49996939 toolboard_t0: mcu_awake=0.232 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=72304 bytes_read=2583584 bytes_retransmit=9 bytes_invalid=0 send_seq=10010 receive_seq=10010 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997798 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16758 bytes_read=143156 bytes_retransmit=9 bytes_invalid=0 send_seq=1992 receive_seq=1992 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997580 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7825 bytes_read=289784 bytes_retransmit=9 bytes_invalid=0 send_seq=1255 receive_seq=1255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8419 bytes_read=25162 bytes_retransmit=9 bytes_invalid=0 send_seq=1250 receive_seq=1250 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999475 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51495 bytes_read=617788 bytes_retransmit=0 bytes_invalid=0 send_seq=4887 receive_seq=4887 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998691 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.1 th1: temp=49.5 th2: temp=51.8 th3: temp=49.7 sysload=0.24 cputime=151.465 memavail=7405356 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 1153.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17637230 bytes_read=1924163 bytes_retransmit=9 bytes_invalid=0 send_seq=299461 receive_seq=299461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015774 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7672 bytes_read=25661 bytes_retransmit=0 bytes_invalid=0 send_seq=1250 receive_seq=1250 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998942 adj=49996865 toolboard_t0: mcu_awake=0.232 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=72310 bytes_read=2583712 bytes_retransmit=9 bytes_invalid=0 send_seq=10011 receive_seq=10011 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997779 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16764 bytes_read=143298 bytes_retransmit=9 bytes_invalid=0 send_seq=1993 receive_seq=1993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7831 bytes_read=290078 bytes_retransmit=9 bytes_invalid=0 send_seq=1256 receive_seq=1256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997602 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8425 bytes_read=25178 bytes_retransmit=9 bytes_invalid=0 send_seq=1251 receive_seq=1251 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999458 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51501 bytes_read=618144 bytes_retransmit=0 bytes_invalid=0 send_seq=4888 receive_seq=4888 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998638 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.2 th1: temp=49.4 th2: temp=51.7 th3: temp=49.9 sysload=0.24 cputime=151.508 memavail=7405356 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 1154.7: gcodein=0  mcu: mcu_awake=0.021 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17637528 bytes_read=1924588 bytes_retransmit=9 bytes_invalid=0 send_seq=299484 receive_seq=299484 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015798 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7678 bytes_read=25677 bytes_retransmit=0 bytes_invalid=0 send_seq=1251 receive_seq=1251 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998941 adj=49996869 toolboard_t0: mcu_awake=0.232 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=72316 bytes_read=2583812 bytes_retransmit=9 bytes_invalid=0 send_seq=10012 receive_seq=10012 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997737 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16770 bytes_read=143398 bytes_retransmit=9 bytes_invalid=0 send_seq=1994 receive_seq=1994 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997565 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7837 bytes_read=290327 bytes_retransmit=9 bytes_invalid=0 send_seq=1257 receive_seq=1257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997599 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8431 bytes_read=25194 bytes_retransmit=9 bytes_invalid=0 send_seq=1252 receive_seq=1252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51507 bytes_read=618500 bytes_retransmit=0 bytes_invalid=0 send_seq=4889 receive_seq=4889 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998618 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.5 th1: temp=49.2 th2: temp=51.7 th3: temp=49.6 sysload=0.24 cputime=151.550 memavail=7405356 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1155.7: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17637826 bytes_read=1925058 bytes_retransmit=9 bytes_invalid=0 send_seq=299507 receive_seq=299507 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015820 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7684 bytes_read=25693 bytes_retransmit=0 bytes_invalid=0 send_seq=1252 receive_seq=1252 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998941 adj=49996832 toolboard_t0: mcu_awake=0.232 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=72322 bytes_read=2583912 bytes_retransmit=9 bytes_invalid=0 send_seq=10013 receive_seq=10013 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997834 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16776 bytes_read=143498 bytes_retransmit=9 bytes_invalid=0 send_seq=1995 receive_seq=1995 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997521 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7843 bytes_read=290561 bytes_retransmit=9 bytes_invalid=0 send_seq=1258 receive_seq=1258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997569 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8437 bytes_read=25210 bytes_retransmit=9 bytes_invalid=0 send_seq=1253 receive_seq=1253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51513 bytes_read=618856 bytes_retransmit=0 bytes_invalid=0 send_seq=4890 receive_seq=4890 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998586 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.5 th1: temp=49.5 th2: temp=51.9 th3: temp=49.7 sysload=0.24 cputime=151.591 memavail=7405168 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1156.7: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17638124 bytes_read=1925483 bytes_retransmit=9 bytes_invalid=0 send_seq=299530 receive_seq=299530 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015831 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7690 bytes_read=25709 bytes_retransmit=0 bytes_invalid=0 send_seq=1253 receive_seq=1253 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998940 adj=49996825 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72328 bytes_read=2584054 bytes_retransmit=9 bytes_invalid=0 send_seq=10014 receive_seq=10014 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997703 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16782 bytes_read=143626 bytes_retransmit=9 bytes_invalid=0 send_seq=1996 receive_seq=1996 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997446 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7849 bytes_read=290855 bytes_retransmit=9 bytes_invalid=0 send_seq=1259 receive_seq=1259 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997538 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8443 bytes_read=25237 bytes_retransmit=9 bytes_invalid=0 send_seq=1254 receive_seq=1254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999423 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51519 bytes_read=619212 bytes_retransmit=0 bytes_invalid=0 send_seq=4891 receive_seq=4891 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998558 coil_temp=17.7 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=50.4 th1: temp=49.4 th2: temp=51.5 th3: temp=49.7 sysload=0.22 cputime=151.634 memavail=7405168 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1157.7: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17638422 bytes_read=1925908 bytes_retransmit=9 bytes_invalid=0 send_seq=299553 receive_seq=299553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015811 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7696 bytes_read=25738 bytes_retransmit=0 bytes_invalid=0 send_seq=1254 receive_seq=1254 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998942 adj=49996824 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72334 bytes_read=2584154 bytes_retransmit=9 bytes_invalid=0 send_seq=10015 receive_seq=10015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997631 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16788 bytes_read=143726 bytes_retransmit=9 bytes_invalid=0 send_seq=1997 receive_seq=1997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997414 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7855 bytes_read=291089 bytes_retransmit=9 bytes_invalid=0 send_seq=1260 receive_seq=1260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997536 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8449 bytes_read=25253 bytes_retransmit=9 bytes_invalid=0 send_seq=1255 receive_seq=1255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999422 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51525 bytes_read=619568 bytes_retransmit=0 bytes_invalid=0 send_seq=4892 receive_seq=4892 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998580 coil_temp=17.7 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=50.6 th1: temp=49.4 th2: temp=51.4 th3: temp=49.7 sysload=0.22 cputime=151.676 memavail=7405168 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 1158.7: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17638720 bytes_read=1926358 bytes_retransmit=9 bytes_invalid=0 send_seq=299576 receive_seq=299576 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015799 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7702 bytes_read=25754 bytes_retransmit=0 bytes_invalid=0 send_seq=1255 receive_seq=1255 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998940 adj=49996924 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72340 bytes_read=2584254 bytes_retransmit=9 bytes_invalid=0 send_seq=10016 receive_seq=10016 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997677 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16794 bytes_read=143840 bytes_retransmit=9 bytes_invalid=0 send_seq=1998 receive_seq=1998 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7861 bytes_read=291323 bytes_retransmit=9 bytes_invalid=0 send_seq=1261 receive_seq=1261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997597 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8455 bytes_read=25269 bytes_retransmit=9 bytes_invalid=0 send_seq=1256 receive_seq=1256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51531 bytes_read=619924 bytes_retransmit=0 bytes_invalid=0 send_seq=4893 receive_seq=4893 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998617 coil_temp=17.7 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=50.8 th1: temp=49.6 th2: temp=51.8 th3: temp=49.9 sysload=0.22 cputime=151.718 memavail=7405168 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 1159.7: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=17639018 bytes_read=1926782 bytes_retransmit=9 bytes_invalid=0 send_seq=299599 receive_seq=299599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015786 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7708 bytes_read=25770 bytes_retransmit=0 bytes_invalid=0 send_seq=1256 receive_seq=1256 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998940 adj=49996939 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72346 bytes_read=2584382 bytes_retransmit=9 bytes_invalid=0 send_seq=10017 receive_seq=10017 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997689 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16800 bytes_read=143968 bytes_retransmit=9 bytes_invalid=0 send_seq=1999 receive_seq=1999 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7867 bytes_read=291632 bytes_retransmit=9 bytes_invalid=0 send_seq=1262 receive_seq=1262 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997621 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8461 bytes_read=25285 bytes_retransmit=9 bytes_invalid=0 send_seq=1257 receive_seq=1257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51537 bytes_read=620280 bytes_retransmit=0 bytes_invalid=0 send_seq=4894 receive_seq=4894 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998629 coil_temp=17.7 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=50.6 th1: temp=49.3 th2: temp=51.8 th3: temp=49.7 sysload=0.22 cputime=151.760 memavail=7405168 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1160.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17639316 bytes_read=1927222 bytes_retransmit=9 bytes_invalid=0 send_seq=299622 receive_seq=299622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015773 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7714 bytes_read=25786 bytes_retransmit=0 bytes_invalid=0 send_seq=1257 receive_seq=1257 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998939 adj=49996959 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72352 bytes_read=2584482 bytes_retransmit=9 bytes_invalid=0 send_seq=10018 receive_seq=10018 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997696 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16806 bytes_read=144068 bytes_retransmit=9 bytes_invalid=0 send_seq=2000 receive_seq=2000 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997529 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7873 bytes_read=291866 bytes_retransmit=9 bytes_invalid=0 send_seq=1263 receive_seq=1263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8467 bytes_read=25301 bytes_retransmit=9 bytes_invalid=0 send_seq=1258 receive_seq=1258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51543 bytes_read=620636 bytes_retransmit=0 bytes_invalid=0 send_seq=4895 receive_seq=4895 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998647 coil_temp=17.7 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=50.9 th1: temp=49.6 th2: temp=51.5 th3: temp=49.6 sysload=0.22 cputime=151.802 memavail=7405168 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1161.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17639614 bytes_read=1927676 bytes_retransmit=9 bytes_invalid=0 send_seq=299645 receive_seq=299645 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015768 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7720 bytes_read=25802 bytes_retransmit=0 bytes_invalid=0 send_seq=1258 receive_seq=1258 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998937 adj=49996977 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=72358 bytes_read=2584596 bytes_retransmit=9 bytes_invalid=0 send_seq=10019 receive_seq=10019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997688 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16812 bytes_read=144168 bytes_retransmit=9 bytes_invalid=0 send_seq=2001 receive_seq=2001 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7879 bytes_read=292100 bytes_retransmit=9 bytes_invalid=0 send_seq=1264 receive_seq=1264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8473 bytes_read=25328 bytes_retransmit=9 bytes_invalid=0 send_seq=1259 receive_seq=1259 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51549 bytes_read=620992 bytes_retransmit=0 bytes_invalid=0 send_seq=4896 receive_seq=4896 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998656 coil_temp=17.7 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=50.4 th1: temp=49.9 th2: temp=51.9 th3: temp=49.7 sysload=0.20 cputime=151.845 memavail=7405168 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1162.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17639912 bytes_read=1928101 bytes_retransmit=9 bytes_invalid=0 send_seq=299668 receive_seq=299668 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015756 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7726 bytes_read=25831 bytes_retransmit=0 bytes_invalid=0 send_seq=1259 receive_seq=1259 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998935 adj=49996948 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=72364 bytes_read=2584724 bytes_retransmit=9 bytes_invalid=0 send_seq=10020 receive_seq=10020 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997678 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16818 bytes_read=144296 bytes_retransmit=9 bytes_invalid=0 send_seq=2002 receive_seq=2002 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997527 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7885 bytes_read=292394 bytes_retransmit=9 bytes_invalid=0 send_seq=1265 receive_seq=1265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8479 bytes_read=25344 bytes_retransmit=9 bytes_invalid=0 send_seq=1260 receive_seq=1260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51555 bytes_read=621348 bytes_retransmit=0 bytes_invalid=0 send_seq=4897 receive_seq=4897 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998646 coil_temp=17.7 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=50.6 th1: temp=49.7 th2: temp=51.6 th3: temp=49.7 sysload=0.20 cputime=151.887 memavail=7405168 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 1163.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17640210 bytes_read=1928526 bytes_retransmit=9 bytes_invalid=0 send_seq=299691 receive_seq=299691 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015744 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7732 bytes_read=25847 bytes_retransmit=0 bytes_invalid=0 send_seq=1260 receive_seq=1260 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998935 adj=49996951 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=72370 bytes_read=2584824 bytes_retransmit=9 bytes_invalid=0 send_seq=10021 receive_seq=10021 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997688 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16824 bytes_read=144410 bytes_retransmit=9 bytes_invalid=0 send_seq=2003 receive_seq=2003 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997541 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=7891 bytes_read=292628 bytes_retransmit=9 bytes_invalid=0 send_seq=1266 receive_seq=1266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997722 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8485 bytes_read=25360 bytes_retransmit=9 bytes_invalid=0 send_seq=1261 receive_seq=1261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51561 bytes_read=621704 bytes_retransmit=0 bytes_invalid=0 send_seq=4898 receive_seq=4898 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998645 coil_temp=17.7 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=50.4 th1: temp=49.7 th2: temp=51.6 th3: temp=49.6 sysload=0.20 cputime=151.930 memavail=7405192 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 1164.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17640514 bytes_read=1928996 bytes_retransmit=9 bytes_invalid=0 send_seq=299715 receive_seq=299715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015725 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7744 bytes_read=25879 bytes_retransmit=0 bytes_invalid=0 send_seq=1262 receive_seq=1262 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998933 adj=49996972 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=72382 bytes_read=2584940 bytes_retransmit=9 bytes_invalid=0 send_seq=10023 receive_seq=10023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997681 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16836 bytes_read=144526 bytes_retransmit=9 bytes_invalid=0 send_seq=2005 receive_seq=2005 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997550 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7903 bytes_read=292893 bytes_retransmit=9 bytes_invalid=0 send_seq=1268 receive_seq=1268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997720 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8497 bytes_read=25392 bytes_retransmit=9 bytes_invalid=0 send_seq=1263 receive_seq=1263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51573 bytes_read=622076 bytes_retransmit=0 bytes_invalid=0 send_seq=4900 receive_seq=4900 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998657 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.9 th1: temp=49.7 th2: temp=51.7 th3: temp=49.5 sysload=0.20 cputime=151.974 memavail=7405216 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1165.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=17640812 bytes_read=1929436 bytes_retransmit=9 bytes_invalid=0 send_seq=299738 receive_seq=299738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015728 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7750 bytes_read=25895 bytes_retransmit=0 bytes_invalid=0 send_seq=1263 receive_seq=1263 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998933 adj=49996980 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=72388 bytes_read=2585068 bytes_retransmit=9 bytes_invalid=0 send_seq=10024 receive_seq=10024 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997666 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16842 bytes_read=144654 bytes_retransmit=9 bytes_invalid=0 send_seq=2006 receive_seq=2006 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997569 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7909 bytes_read=293187 bytes_retransmit=9 bytes_invalid=0 send_seq=1269 receive_seq=1269 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997750 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8503 bytes_read=25408 bytes_retransmit=9 bytes_invalid=0 send_seq=1264 receive_seq=1264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999456 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51579 bytes_read=622421 bytes_retransmit=0 bytes_invalid=0 send_seq=4901 receive_seq=4901 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998704 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.8 th1: temp=49.9 th2: temp=51.9 th3: temp=49.7 sysload=0.20 cputime=152.024 memavail=7404856 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1166.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=17641110 bytes_read=1929861 bytes_retransmit=9 bytes_invalid=0 send_seq=299761 receive_seq=299761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015736 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7756 bytes_read=25911 bytes_retransmit=0 bytes_invalid=0 send_seq=1264 receive_seq=1264 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998932 adj=49996971 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72394 bytes_read=2585182 bytes_retransmit=9 bytes_invalid=0 send_seq=10025 receive_seq=10025 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997631 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16848 bytes_read=144754 bytes_retransmit=9 bytes_invalid=0 send_seq=2007 receive_seq=2007 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997535 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7915 bytes_read=293421 bytes_retransmit=9 bytes_invalid=0 send_seq=1270 receive_seq=1270 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997711 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8509 bytes_read=25435 bytes_retransmit=9 bytes_invalid=0 send_seq=1265 receive_seq=1265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51585 bytes_read=622766 bytes_retransmit=0 bytes_invalid=0 send_seq=4902 receive_seq=4902 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998688 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.8 th1: temp=49.8 th2: temp=51.7 th3: temp=49.6 sysload=0.19 cputime=152.065 memavail=7404860 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 1167.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=17641408 bytes_read=1930315 bytes_retransmit=9 bytes_invalid=0 send_seq=299784 receive_seq=299784 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015723 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7762 bytes_read=25940 bytes_retransmit=0 bytes_invalid=0 send_seq=1265 receive_seq=1265 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998932 adj=49996935 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72400 bytes_read=2585282 bytes_retransmit=9 bytes_invalid=0 send_seq=10026 receive_seq=10026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997616 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16854 bytes_read=144854 bytes_retransmit=9 bytes_invalid=0 send_seq=2008 receive_seq=2008 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997575 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7921 bytes_read=293655 bytes_retransmit=9 bytes_invalid=0 send_seq=1271 receive_seq=1271 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8515 bytes_read=25451 bytes_retransmit=9 bytes_invalid=0 send_seq=1266 receive_seq=1266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51591 bytes_read=623110 bytes_retransmit=0 bytes_invalid=0 send_seq=4903 receive_seq=4903 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998662 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=50.7 th1: temp=49.7 th2: temp=51.6 th3: temp=49.7 sysload=0.19 cputime=152.106 memavail=7404860 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1168.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=17641706 bytes_read=1930740 bytes_retransmit=9 bytes_invalid=0 send_seq=299807 receive_seq=299807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015716 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7768 bytes_read=25956 bytes_retransmit=0 bytes_invalid=0 send_seq=1266 receive_seq=1266 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998931 adj=49996974 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72406 bytes_read=2585410 bytes_retransmit=9 bytes_invalid=0 send_seq=10027 receive_seq=10027 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997650 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16860 bytes_read=144996 bytes_retransmit=9 bytes_invalid=0 send_seq=2009 receive_seq=2009 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997587 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7927 bytes_read=293949 bytes_retransmit=9 bytes_invalid=0 send_seq=1272 receive_seq=1272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8521 bytes_read=25467 bytes_retransmit=9 bytes_invalid=0 send_seq=1267 receive_seq=1267 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51597 bytes_read=623455 bytes_retransmit=0 bytes_invalid=0 send_seq=4904 receive_seq=4904 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998659 coil_temp=17.7 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=50.9 th1: temp=49.7 th2: temp=51.5 th3: temp=49.6 sysload=0.19 cputime=152.150 memavail=7404860 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1169.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=17642004 bytes_read=1931160 bytes_retransmit=9 bytes_invalid=0 send_seq=299830 receive_seq=299830 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015709 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7774 bytes_read=25972 bytes_retransmit=0 bytes_invalid=0 send_seq=1267 receive_seq=1267 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998930 adj=49996966 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72412 bytes_read=2585510 bytes_retransmit=9 bytes_invalid=0 send_seq=10028 receive_seq=10028 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997665 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16866 bytes_read=145096 bytes_retransmit=9 bytes_invalid=0 send_seq=2010 receive_seq=2010 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997574 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7933 bytes_read=294198 bytes_retransmit=9 bytes_invalid=0 send_seq=1273 receive_seq=1273 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8527 bytes_read=25483 bytes_retransmit=9 bytes_invalid=0 send_seq=1268 receive_seq=1268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51603 bytes_read=623800 bytes_retransmit=0 bytes_invalid=0 send_seq=4905 receive_seq=4905 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998661 coil_temp=17.7 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=50.7 th1: temp=49.8 th2: temp=51.6 th3: temp=49.8 sysload=0.19 cputime=152.193 memavail=7405348 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1170.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17642297 bytes_read=1931624 bytes_retransmit=9 bytes_invalid=0 send_seq=299852 receive_seq=299852 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015741 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7780 bytes_read=25988 bytes_retransmit=0 bytes_invalid=0 send_seq=1268 receive_seq=1268 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998932 adj=49996967 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72418 bytes_read=2585610 bytes_retransmit=9 bytes_invalid=0 send_seq=10029 receive_seq=10029 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997664 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16872 bytes_read=145196 bytes_retransmit=9 bytes_invalid=0 send_seq=2011 receive_seq=2011 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997564 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7939 bytes_read=294432 bytes_retransmit=9 bytes_invalid=0 send_seq=1274 receive_seq=1274 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8533 bytes_read=25499 bytes_retransmit=9 bytes_invalid=0 send_seq=1269 receive_seq=1269 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51609 bytes_read=624145 bytes_retransmit=0 bytes_invalid=0 send_seq=4906 receive_seq=4906 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998673 coil_temp=17.7 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=50.9 th1: temp=49.8 th2: temp=51.8 th3: temp=49.7 sysload=0.19 cputime=152.240 memavail=7405136 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1171.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17642595 bytes_read=1932049 bytes_retransmit=9 bytes_invalid=0 send_seq=299875 receive_seq=299875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015731 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7786 bytes_read=26004 bytes_retransmit=0 bytes_invalid=0 send_seq=1269 receive_seq=1269 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998932 adj=49996933 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72424 bytes_read=2585752 bytes_retransmit=9 bytes_invalid=0 send_seq=10030 receive_seq=10030 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997578 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16878 bytes_read=145324 bytes_retransmit=9 bytes_invalid=0 send_seq=2012 receive_seq=2012 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997468 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7945 bytes_read=294726 bytes_retransmit=9 bytes_invalid=0 send_seq=1275 receive_seq=1275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997616 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8539 bytes_read=25526 bytes_retransmit=9 bytes_invalid=0 send_seq=1270 receive_seq=1270 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51615 bytes_read=624490 bytes_retransmit=0 bytes_invalid=0 send_seq=4907 receive_seq=4907 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998701 coil_temp=17.7 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=50.9 th1: temp=49.7 th2: temp=51.7 th3: temp=49.7 sysload=0.25 cputime=152.366 memavail=7403120 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1172.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17642888 bytes_read=1932469 bytes_retransmit=9 bytes_invalid=0 send_seq=299897 receive_seq=299897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015776 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7792 bytes_read=26033 bytes_retransmit=0 bytes_invalid=0 send_seq=1270 receive_seq=1270 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998932 adj=49996962 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72430 bytes_read=2585852 bytes_retransmit=9 bytes_invalid=0 send_seq=10031 receive_seq=10031 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997675 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16884 bytes_read=145424 bytes_retransmit=9 bytes_invalid=0 send_seq=2013 receive_seq=2013 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7951 bytes_read=294960 bytes_retransmit=9 bytes_invalid=0 send_seq=1276 receive_seq=1276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8545 bytes_read=25542 bytes_retransmit=9 bytes_invalid=0 send_seq=1271 receive_seq=1271 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51621 bytes_read=624835 bytes_retransmit=0 bytes_invalid=0 send_seq=4908 receive_seq=4908 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998842 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=51.0 th1: temp=49.9 th2: temp=51.6 th3: temp=49.7 sysload=0.25 cputime=152.443 memavail=7405072 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1173.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17643181 bytes_read=1932918 bytes_retransmit=9 bytes_invalid=0 send_seq=299919 receive_seq=299919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015856 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7798 bytes_read=26049 bytes_retransmit=0 bytes_invalid=0 send_seq=1271 receive_seq=1271 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998933 adj=49996874 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72436 bytes_read=2585952 bytes_retransmit=9 bytes_invalid=0 send_seq=10032 receive_seq=10032 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997549 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16890 bytes_read=145524 bytes_retransmit=9 bytes_invalid=0 send_seq=2014 receive_seq=2014 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997409 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7957 bytes_read=295194 bytes_retransmit=9 bytes_invalid=0 send_seq=1277 receive_seq=1277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997557 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8551 bytes_read=25558 bytes_retransmit=9 bytes_invalid=0 send_seq=1272 receive_seq=1272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999419 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51627 bytes_read=625187 bytes_retransmit=0 bytes_invalid=0 send_seq=4909 receive_seq=4909 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998720 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=50.9 th1: temp=50.0 th2: temp=51.8 th3: temp=49.5 sysload=0.25 cputime=152.486 memavail=7404988 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1174.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17643479 bytes_read=1933343 bytes_retransmit=9 bytes_invalid=0 send_seq=299942 receive_seq=299942 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015844 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7804 bytes_read=26065 bytes_retransmit=0 bytes_invalid=0 send_seq=1272 receive_seq=1272 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998931 adj=49996760 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72442 bytes_read=2586080 bytes_retransmit=9 bytes_invalid=0 send_seq=10033 receive_seq=10033 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997374 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16896 bytes_read=145666 bytes_retransmit=9 bytes_invalid=0 send_seq=2015 receive_seq=2015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997234 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7963 bytes_read=295503 bytes_retransmit=9 bytes_invalid=0 send_seq=1278 receive_seq=1278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997435 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8557 bytes_read=25574 bytes_retransmit=9 bytes_invalid=0 send_seq=1273 receive_seq=1273 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999389 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51633 bytes_read=625543 bytes_retransmit=0 bytes_invalid=0 send_seq=4910 receive_seq=4910 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998585 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=50.9 th1: temp=49.8 th2: temp=51.7 th3: temp=49.8 sysload=0.25 cputime=152.530 memavail=7404988 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1175.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=17643777 bytes_read=1933797 bytes_retransmit=9 bytes_invalid=0 send_seq=299965 receive_seq=299965 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015826 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7810 bytes_read=26081 bytes_retransmit=0 bytes_invalid=0 send_seq=1273 receive_seq=1273 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998930 adj=49996806 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72448 bytes_read=2586180 bytes_retransmit=9 bytes_invalid=0 send_seq=10034 receive_seq=10034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997470 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16902 bytes_read=145766 bytes_retransmit=9 bytes_invalid=0 send_seq=2016 receive_seq=2016 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997318 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7969 bytes_read=295737 bytes_retransmit=9 bytes_invalid=0 send_seq=1279 receive_seq=1279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997512 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8563 bytes_read=25590 bytes_retransmit=9 bytes_invalid=0 send_seq=1274 receive_seq=1274 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999408 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51639 bytes_read=625899 bytes_retransmit=0 bytes_invalid=0 send_seq=4911 receive_seq=4911 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998606 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=51.1 th1: temp=49.9 th2: temp=51.5 th3: temp=49.6 sysload=0.25 cputime=152.576 memavail=7407672 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 1176.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=17644075 bytes_read=1934237 bytes_retransmit=9 bytes_invalid=0 send_seq=299988 receive_seq=299988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015808 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7816 bytes_read=26097 bytes_retransmit=0 bytes_invalid=0 send_seq=1274 receive_seq=1274 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998929 adj=49996854 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72454 bytes_read=2586294 bytes_retransmit=9 bytes_invalid=0 send_seq=10035 receive_seq=10035 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997549 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16908 bytes_read=145866 bytes_retransmit=9 bytes_invalid=0 send_seq=2017 receive_seq=2017 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997396 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7975 bytes_read=295971 bytes_retransmit=9 bytes_invalid=0 send_seq=1280 receive_seq=1280 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997570 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8569 bytes_read=25617 bytes_retransmit=9 bytes_invalid=0 send_seq=1275 receive_seq=1275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51645 bytes_read=626255 bytes_retransmit=0 bytes_invalid=0 send_seq=4912 receive_seq=4912 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998625 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=50.9 th1: temp=50.0 th2: temp=51.6 th3: temp=49.6 sysload=0.23 cputime=152.619 memavail=7407672 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1177.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=17644373 bytes_read=1934662 bytes_retransmit=9 bytes_invalid=0 send_seq=300011 receive_seq=300011 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015801 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7822 bytes_read=26126 bytes_retransmit=0 bytes_invalid=0 send_seq=1275 receive_seq=1275 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998929 adj=49996903 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72460 bytes_read=2586422 bytes_retransmit=9 bytes_invalid=0 send_seq=10036 receive_seq=10036 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997599 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16914 bytes_read=145994 bytes_retransmit=9 bytes_invalid=0 send_seq=2018 receive_seq=2018 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997463 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7981 bytes_read=296265 bytes_retransmit=9 bytes_invalid=0 send_seq=1281 receive_seq=1281 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8575 bytes_read=25633 bytes_retransmit=9 bytes_invalid=0 send_seq=1276 receive_seq=1276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51651 bytes_read=626611 bytes_retransmit=0 bytes_invalid=0 send_seq=4913 receive_seq=4913 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998653 coil_temp=17.7 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=51.0 th1: temp=49.8 th2: temp=51.7 th3: temp=49.8 sysload=0.23 cputime=152.662 memavail=7407420 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 1178.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=17644671 bytes_read=1935101 bytes_retransmit=9 bytes_invalid=0 send_seq=300034 receive_seq=300034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015791 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7828 bytes_read=26142 bytes_retransmit=0 bytes_invalid=0 send_seq=1276 receive_seq=1276 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998928 adj=49996926 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72466 bytes_read=2586522 bytes_retransmit=9 bytes_invalid=0 send_seq=10037 receive_seq=10037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997623 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16920 bytes_read=146094 bytes_retransmit=9 bytes_invalid=0 send_seq=2019 receive_seq=2019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997494 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=7987 bytes_read=296499 bytes_retransmit=9 bytes_invalid=0 send_seq=1282 receive_seq=1282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997748 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8581 bytes_read=25649 bytes_retransmit=9 bytes_invalid=0 send_seq=1277 receive_seq=1277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51657 bytes_read=626967 bytes_retransmit=0 bytes_invalid=0 send_seq=4914 receive_seq=4914 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998684 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=50.8 th1: temp=49.9 th2: temp=51.7 th3: temp=49.8 sysload=0.23 cputime=152.705 memavail=7407168 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1179.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=17644969 bytes_read=1935541 bytes_retransmit=9 bytes_invalid=0 send_seq=300057 receive_seq=300057 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015773 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7834 bytes_read=26158 bytes_retransmit=0 bytes_invalid=0 send_seq=1277 receive_seq=1277 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998927 adj=49996943 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72472 bytes_read=2586622 bytes_retransmit=9 bytes_invalid=0 send_seq=10038 receive_seq=10038 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997791 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16926 bytes_read=146208 bytes_retransmit=9 bytes_invalid=0 send_seq=2020 receive_seq=2020 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997516 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7993 bytes_read=296748 bytes_retransmit=9 bytes_invalid=0 send_seq=1283 receive_seq=1283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997733 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8587 bytes_read=25665 bytes_retransmit=9 bytes_invalid=0 send_seq=1278 receive_seq=1278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51663 bytes_read=627323 bytes_retransmit=0 bytes_invalid=0 send_seq=4915 receive_seq=4915 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998706 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=50.8 th1: temp=50.0 th2: temp=51.6 th3: temp=49.5 sysload=0.23 cputime=152.750 memavail=7407184 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 1180.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17645267 bytes_read=1935976 bytes_retransmit=9 bytes_invalid=0 send_seq=300080 receive_seq=300080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015759 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7840 bytes_read=26174 bytes_retransmit=0 bytes_invalid=0 send_seq=1278 receive_seq=1278 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998927 adj=49996966 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72478 bytes_read=2586750 bytes_retransmit=9 bytes_invalid=0 send_seq=10039 receive_seq=10039 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997867 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16932 bytes_read=146336 bytes_retransmit=9 bytes_invalid=0 send_seq=2021 receive_seq=2021 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997567 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=7999 bytes_read=297042 bytes_retransmit=9 bytes_invalid=0 send_seq=1284 receive_seq=1284 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997760 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8593 bytes_read=25681 bytes_retransmit=9 bytes_invalid=0 send_seq=1279 receive_seq=1279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51669 bytes_read=627679 bytes_retransmit=0 bytes_invalid=0 send_seq=4916 receive_seq=4916 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998687 coil_temp=17.6 refs=0 mcu_temp=20.91 supply_voltage=3.012 th0: temp=50.8 th1: temp=49.9 th2: temp=51.4 th3: temp=49.6 sysload=0.23 cputime=152.794 memavail=7407184 print_time=1174.806 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1181.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17645621 bytes_read=1936415 bytes_retransmit=9 bytes_invalid=0 send_seq=300103 receive_seq=300103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015769 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7846 bytes_read=26190 bytes_retransmit=0 bytes_invalid=0 send_seq=1279 receive_seq=1279 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998929 adj=49996987 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72484 bytes_read=2586864 bytes_retransmit=9 bytes_invalid=0 send_seq=10040 receive_seq=10040 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997818 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16938 bytes_read=146436 bytes_retransmit=9 bytes_invalid=0 send_seq=2022 receive_seq=2022 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997586 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8005 bytes_read=297276 bytes_retransmit=9 bytes_invalid=0 send_seq=1285 receive_seq=1285 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997813 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8599 bytes_read=25708 bytes_retransmit=9 bytes_invalid=0 send_seq=1280 receive_seq=1280 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51675 bytes_read=628035 bytes_retransmit=0 bytes_invalid=0 send_seq=4917 receive_seq=4917 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998726 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=51.0 th1: temp=49.9 th2: temp=51.6 th3: temp=49.6 sysload=0.21 cputime=152.887 memavail=7407196 print_time=1204.303 buffer_time=0.153 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1182.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17645627 bytes_read=1936533 bytes_retransmit=9 bytes_invalid=0 send_seq=300104 receive_seq=300104 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015761 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7852 bytes_read=26219 bytes_retransmit=0 bytes_invalid=0 send_seq=1280 receive_seq=1280 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998928 adj=49996986 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72490 bytes_read=2586964 bytes_retransmit=9 bytes_invalid=0 send_seq=10041 receive_seq=10041 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997828 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16944 bytes_read=146536 bytes_retransmit=9 bytes_invalid=0 send_seq=2023 receive_seq=2023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997534 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8011 bytes_read=297510 bytes_retransmit=9 bytes_invalid=0 send_seq=1286 receive_seq=1286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997736 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8605 bytes_read=25724 bytes_retransmit=9 bytes_invalid=0 send_seq=1281 receive_seq=1281 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51681 bytes_read=628391 bytes_retransmit=0 bytes_invalid=0 send_seq=4918 receive_seq=4918 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998683 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=50.8 th1: temp=50.0 th2: temp=51.4 th3: temp=49.5 sysload=0.21 cputime=152.923 memavail=7400404 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1183.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17645633 bytes_read=1936636 bytes_retransmit=9 bytes_invalid=0 send_seq=300105 receive_seq=300105 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015751 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7858 bytes_read=26235 bytes_retransmit=0 bytes_invalid=0 send_seq=1281 receive_seq=1281 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998927 adj=49996987 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72496 bytes_read=2587092 bytes_retransmit=9 bytes_invalid=0 send_seq=10042 receive_seq=10042 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997782 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16950 bytes_read=146664 bytes_retransmit=9 bytes_invalid=0 send_seq=2024 receive_seq=2024 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997570 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8017 bytes_read=297804 bytes_retransmit=9 bytes_invalid=0 send_seq=1287 receive_seq=1287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997733 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8611 bytes_read=25740 bytes_retransmit=9 bytes_invalid=0 send_seq=1282 receive_seq=1282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999467 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51687 bytes_read=628747 bytes_retransmit=0 bytes_invalid=0 send_seq=4919 receive_seq=4919 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998670 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=50.7 th1: temp=49.7 th2: temp=51.3 th3: temp=49.5 sysload=0.21 cputime=152.956 memavail=7406536 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1184.7: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17645639 bytes_read=1936753 bytes_retransmit=9 bytes_invalid=0 send_seq=300106 receive_seq=300106 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015769 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7864 bytes_read=26251 bytes_retransmit=0 bytes_invalid=0 send_seq=1282 receive_seq=1282 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998927 adj=49996984 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72502 bytes_read=2587185 bytes_retransmit=9 bytes_invalid=0 send_seq=10043 receive_seq=10043 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997832 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16956 bytes_read=146771 bytes_retransmit=9 bytes_invalid=0 send_seq=2025 receive_seq=2025 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997570 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=8023 bytes_read=298053 bytes_retransmit=9 bytes_invalid=0 send_seq=1288 receive_seq=1288 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997727 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8617 bytes_read=25756 bytes_retransmit=9 bytes_invalid=0 send_seq=1283 receive_seq=1283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51693 bytes_read=629087 bytes_retransmit=0 bytes_invalid=0 send_seq=4920 receive_seq=4920 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998672 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=50.5 th1: temp=49.4 th2: temp=51.2 th3: temp=49.5 sysload=0.21 cputime=152.989 memavail=7406536 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 1185.7: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000003 mcu_task_stddev=0.000005 bytes_write=17645645 bytes_read=1936886 bytes_retransmit=9 bytes_invalid=0 send_seq=300107 receive_seq=300107 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015757 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7870 bytes_read=26267 bytes_retransmit=0 bytes_invalid=0 send_seq=1283 receive_seq=1283 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998927 adj=49996935 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72508 bytes_read=2587276 bytes_retransmit=9 bytes_invalid=0 send_seq=10044 receive_seq=10044 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997734 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16962 bytes_read=146862 bytes_retransmit=9 bytes_invalid=0 send_seq=2026 receive_seq=2026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997503 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=8029 bytes_read=298287 bytes_retransmit=9 bytes_invalid=0 send_seq=1289 receive_seq=1289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8623 bytes_read=25772 bytes_retransmit=9 bytes_invalid=0 send_seq=1284 receive_seq=1284 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51699 bytes_read=629443 bytes_retransmit=0 bytes_invalid=0 send_seq=4921 receive_seq=4921 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998629 coil_temp=17.6 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=50.3 th1: temp=49.4 th2: temp=51.1 th3: temp=49.4 sysload=0.21 cputime=153.021 memavail=7405048 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1186.7: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000003 mcu_task_stddev=0.000005 bytes_write=17645651 bytes_read=1936989 bytes_retransmit=9 bytes_invalid=0 send_seq=300108 receive_seq=300108 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015746 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7876 bytes_read=26283 bytes_retransmit=0 bytes_invalid=0 send_seq=1284 receive_seq=1284 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998929 adj=49996969 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=72514 bytes_read=2587409 bytes_retransmit=9 bytes_invalid=0 send_seq=10045 receive_seq=10045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997727 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16968 bytes_read=146981 bytes_retransmit=9 bytes_invalid=0 send_seq=2027 receive_seq=2027 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997522 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=8035 bytes_read=298581 bytes_retransmit=9 bytes_invalid=0 send_seq=1290 receive_seq=1290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8629 bytes_read=25799 bytes_retransmit=9 bytes_invalid=0 send_seq=1285 receive_seq=1285 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51705 bytes_read=629799 bytes_retransmit=0 bytes_invalid=0 send_seq=4922 receive_seq=4922 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998626 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=50.1 th1: temp=49.1 th2: temp=50.9 th3: temp=49.2 sysload=0.20 cputime=153.054 memavail=7405048 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1187.7: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000003 mcu_task_stddev=0.000005 bytes_write=17645657 bytes_read=1937106 bytes_retransmit=9 bytes_invalid=0 send_seq=300109 receive_seq=300109 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015736 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7882 bytes_read=26312 bytes_retransmit=0 bytes_invalid=0 send_seq=1285 receive_seq=1285 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998930 adj=49997010 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=72520 bytes_read=2587502 bytes_retransmit=9 bytes_invalid=0 send_seq=10046 receive_seq=10046 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997717 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16974 bytes_read=147074 bytes_retransmit=9 bytes_invalid=0 send_seq=2028 receive_seq=2028 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997544 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=8041 bytes_read=298815 bytes_retransmit=9 bytes_invalid=0 send_seq=1291 receive_seq=1291 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8635 bytes_read=25815 bytes_retransmit=9 bytes_invalid=0 send_seq=1286 receive_seq=1286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999479 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51711 bytes_read=630155 bytes_retransmit=0 bytes_invalid=0 send_seq=4923 receive_seq=4923 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998630 coil_temp=17.6 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=49.9 th1: temp=49.0 th2: temp=50.7 th3: temp=49.0 sysload=0.20 cputime=153.086 memavail=7404824 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 1188.7: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000003 mcu_task_stddev=0.000005 bytes_write=17645663 bytes_read=1937224 bytes_retransmit=9 bytes_invalid=0 send_seq=300110 receive_seq=300110 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015729 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7888 bytes_read=26328 bytes_retransmit=0 bytes_invalid=0 send_seq=1286 receive_seq=1286 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998931 adj=49997041 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=72526 bytes_read=2587600 bytes_retransmit=9 bytes_invalid=0 send_seq=10047 receive_seq=10047 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997702 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=16980 bytes_read=147172 bytes_retransmit=9 bytes_invalid=0 send_seq=2029 receive_seq=2029 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997557 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=8047 bytes_read=299049 bytes_retransmit=9 bytes_invalid=0 send_seq=1292 receive_seq=1292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997682 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8641 bytes_read=25831 bytes_retransmit=9 bytes_invalid=0 send_seq=1287 receive_seq=1287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999481 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51717 bytes_read=630511 bytes_retransmit=0 bytes_invalid=0 send_seq=4924 receive_seq=4924 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998633 coil_temp=17.6 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=49.6 th1: temp=48.7 th2: temp=50.5 th3: temp=49.0 sysload=0.20 cputime=153.117 memavail=7404824 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 1189.7: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000003 mcu_task_stddev=0.000005 bytes_write=17645669 bytes_read=1937327 bytes_retransmit=9 bytes_invalid=0 send_seq=300111 receive_seq=300111 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015722 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7894 bytes_read=26344 bytes_retransmit=0 bytes_invalid=0 send_seq=1287 receive_seq=1287 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998930 adj=49997043 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=72532 bytes_read=2587728 bytes_retransmit=9 bytes_invalid=0 send_seq=10048 receive_seq=10048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997698 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16986 bytes_read=147314 bytes_retransmit=9 bytes_invalid=0 send_seq=2030 receive_seq=2030 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=8053 bytes_read=299358 bytes_retransmit=9 bytes_invalid=0 send_seq=1293 receive_seq=1293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997677 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8647 bytes_read=25847 bytes_retransmit=9 bytes_invalid=0 send_seq=1288 receive_seq=1288 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999472 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51723 bytes_read=630867 bytes_retransmit=0 bytes_invalid=0 send_seq=4925 receive_seq=4925 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998635 coil_temp=17.6 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=49.3 th1: temp=48.6 th2: temp=50.3 th3: temp=48.8 sysload=0.20 cputime=153.150 memavail=7404824 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1190.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645675 bytes_read=1937457 bytes_retransmit=9 bytes_invalid=0 send_seq=300112 receive_seq=300112 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015714 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7900 bytes_read=26360 bytes_retransmit=0 bytes_invalid=0 send_seq=1288 receive_seq=1288 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998931 adj=49997021 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=72538 bytes_read=2587828 bytes_retransmit=9 bytes_invalid=0 send_seq=10049 receive_seq=10049 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997687 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16992 bytes_read=147414 bytes_retransmit=9 bytes_invalid=0 send_seq=2031 receive_seq=2031 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=8059 bytes_read=299592 bytes_retransmit=9 bytes_invalid=0 send_seq=1294 receive_seq=1294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997693 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8653 bytes_read=25863 bytes_retransmit=9 bytes_invalid=0 send_seq=1289 receive_seq=1289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999466 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51729 bytes_read=631223 bytes_retransmit=0 bytes_invalid=0 send_seq=4926 receive_seq=4926 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998638 coil_temp=17.6 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=49.1 th1: temp=48.4 th2: temp=50.2 th3: temp=48.7 sysload=0.20 cputime=153.181 memavail=7404824 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1191.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645681 bytes_read=1937571 bytes_retransmit=9 bytes_invalid=0 send_seq=300113 receive_seq=300113 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015719 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7906 bytes_read=26376 bytes_retransmit=0 bytes_invalid=0 send_seq=1289 receive_seq=1289 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998931 adj=49997040 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=72544 bytes_read=2587942 bytes_retransmit=9 bytes_invalid=0 send_seq=10050 receive_seq=10050 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997676 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=16998 bytes_read=147514 bytes_retransmit=9 bytes_invalid=0 send_seq=2032 receive_seq=2032 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997553 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=8065 bytes_read=299826 bytes_retransmit=9 bytes_invalid=0 send_seq=1295 receive_seq=1295 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997704 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8659 bytes_read=25890 bytes_retransmit=9 bytes_invalid=0 send_seq=1290 receive_seq=1290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999462 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51735 bytes_read=631579 bytes_retransmit=0 bytes_invalid=0 send_seq=4927 receive_seq=4927 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998656 coil_temp=17.6 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=48.9 th1: temp=48.2 th2: temp=50.0 th3: temp=48.7 sysload=0.18 cputime=153.213 memavail=7404824 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 1192.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645687 bytes_read=1937674 bytes_retransmit=9 bytes_invalid=0 send_seq=300114 receive_seq=300114 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015712 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7912 bytes_read=26405 bytes_retransmit=0 bytes_invalid=0 send_seq=1290 receive_seq=1290 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998931 adj=49997020 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=72550 bytes_read=2588070 bytes_retransmit=9 bytes_invalid=0 send_seq=10051 receive_seq=10051 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997654 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=17004 bytes_read=147642 bytes_retransmit=9 bytes_invalid=0 send_seq=2033 receive_seq=2033 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997526 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=8071 bytes_read=300120 bytes_retransmit=9 bytes_invalid=0 send_seq=1296 receive_seq=1296 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8665 bytes_read=25906 bytes_retransmit=9 bytes_invalid=0 send_seq=1291 receive_seq=1291 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51741 bytes_read=631935 bytes_retransmit=0 bytes_invalid=0 send_seq=4928 receive_seq=4928 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998632 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.7 th1: temp=48.2 th2: temp=49.8 th3: temp=48.4 sysload=0.18 cputime=153.245 memavail=7404824 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 1193.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645693 bytes_read=1937791 bytes_retransmit=9 bytes_invalid=0 send_seq=300115 receive_seq=300115 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015714 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7918 bytes_read=26421 bytes_retransmit=0 bytes_invalid=0 send_seq=1291 receive_seq=1291 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998931 adj=49997023 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=72556 bytes_read=2588170 bytes_retransmit=9 bytes_invalid=0 send_seq=10052 receive_seq=10052 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997666 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=17010 bytes_read=147742 bytes_retransmit=9 bytes_invalid=0 send_seq=2034 receive_seq=2034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=8077 bytes_read=300354 bytes_retransmit=9 bytes_invalid=0 send_seq=1297 receive_seq=1297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8671 bytes_read=25922 bytes_retransmit=9 bytes_invalid=0 send_seq=1292 receive_seq=1292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51747 bytes_read=632291 bytes_retransmit=0 bytes_invalid=0 send_seq=4929 receive_seq=4929 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998634 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.5 th1: temp=47.9 th2: temp=49.7 th3: temp=48.3 sysload=0.18 cputime=153.276 memavail=7404824 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 1194.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645699 bytes_read=1937909 bytes_retransmit=9 bytes_invalid=0 send_seq=300116 receive_seq=300116 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015717 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7924 bytes_read=26437 bytes_retransmit=0 bytes_invalid=0 send_seq=1292 receive_seq=1292 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998935 adj=49997006 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=72562 bytes_read=2588270 bytes_retransmit=9 bytes_invalid=0 send_seq=10053 receive_seq=10053 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997639 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17016 bytes_read=147856 bytes_retransmit=9 bytes_invalid=0 send_seq=2035 receive_seq=2035 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997516 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=8083 bytes_read=300603 bytes_retransmit=9 bytes_invalid=0 send_seq=1298 receive_seq=1298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8677 bytes_read=25938 bytes_retransmit=9 bytes_invalid=0 send_seq=1293 receive_seq=1293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51753 bytes_read=632647 bytes_retransmit=0 bytes_invalid=0 send_seq=4930 receive_seq=4930 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998629 coil_temp=17.6 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=48.2 th1: temp=47.7 th2: temp=49.6 th3: temp=48.2 sysload=0.18 cputime=153.309 memavail=7404844 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1195.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645705 bytes_read=1938026 bytes_retransmit=9 bytes_invalid=0 send_seq=300117 receive_seq=300117 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015711 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7930 bytes_read=26453 bytes_retransmit=0 bytes_invalid=0 send_seq=1293 receive_seq=1293 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998934 adj=49997039 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=72568 bytes_read=2588398 bytes_retransmit=9 bytes_invalid=0 send_seq=10054 receive_seq=10054 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997623 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17022 bytes_read=147984 bytes_retransmit=9 bytes_invalid=0 send_seq=2036 receive_seq=2036 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000021 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=8089 bytes_read=300897 bytes_retransmit=9 bytes_invalid=0 send_seq=1299 receive_seq=1299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997649 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8683 bytes_read=25954 bytes_retransmit=9 bytes_invalid=0 send_seq=1294 receive_seq=1294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999455 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51759 bytes_read=633003 bytes_retransmit=0 bytes_invalid=0 send_seq=4931 receive_seq=4931 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998622 coil_temp=17.7 refs=0 mcu_temp=20.91 supply_voltage=3.012 th0: temp=48.0 th1: temp=47.6 th2: temp=49.5 th3: temp=48.1 sysload=0.18 cputime=153.343 memavail=7404756 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 1196.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645711 bytes_read=1938143 bytes_retransmit=9 bytes_invalid=0 send_seq=300118 receive_seq=300118 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015704 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7936 bytes_read=26469 bytes_retransmit=0 bytes_invalid=0 send_seq=1294 receive_seq=1294 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998933 adj=49997024 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=72574 bytes_read=2588498 bytes_retransmit=9 bytes_invalid=0 send_seq=10055 receive_seq=10055 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997638 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17028 bytes_read=148084 bytes_retransmit=9 bytes_invalid=0 send_seq=2037 receive_seq=2037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=8095 bytes_read=301131 bytes_retransmit=9 bytes_invalid=0 send_seq=1300 receive_seq=1300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8689 bytes_read=25981 bytes_retransmit=9 bytes_invalid=0 send_seq=1295 receive_seq=1295 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51765 bytes_read=633359 bytes_retransmit=0 bytes_invalid=0 send_seq=4932 receive_seq=4932 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998625 coil_temp=17.7 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=47.8 th1: temp=47.6 th2: temp=49.3 th3: temp=48.0 sysload=0.16 cputime=153.375 memavail=7404756 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 1197.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645717 bytes_read=1938261 bytes_retransmit=9 bytes_invalid=0 send_seq=300119 receive_seq=300119 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015698 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7942 bytes_read=26498 bytes_retransmit=0 bytes_invalid=0 send_seq=1295 receive_seq=1295 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998933 adj=49997006 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72580 bytes_read=2588612 bytes_retransmit=9 bytes_invalid=0 send_seq=10056 receive_seq=10056 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997653 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17034 bytes_read=148184 bytes_retransmit=9 bytes_invalid=0 send_seq=2038 receive_seq=2038 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997543 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=8101 bytes_read=301365 bytes_retransmit=9 bytes_invalid=0 send_seq=1301 receive_seq=1301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997697 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8695 bytes_read=25997 bytes_retransmit=9 bytes_invalid=0 send_seq=1296 receive_seq=1296 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51771 bytes_read=633715 bytes_retransmit=0 bytes_invalid=0 send_seq=4933 receive_seq=4933 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998624 coil_temp=17.7 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.4 th2: temp=49.2 th3: temp=48.0 sysload=0.16 cputime=153.408 memavail=7404776 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 1198.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645723 bytes_read=1938364 bytes_retransmit=9 bytes_invalid=0 send_seq=300120 receive_seq=300120 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015694 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7948 bytes_read=26514 bytes_retransmit=0 bytes_invalid=0 send_seq=1296 receive_seq=1296 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998933 adj=49997009 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72586 bytes_read=2588740 bytes_retransmit=9 bytes_invalid=0 send_seq=10057 receive_seq=10057 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997657 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17040 bytes_read=148312 bytes_retransmit=9 bytes_invalid=0 send_seq=2039 receive_seq=2039 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997589 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=8107 bytes_read=301659 bytes_retransmit=9 bytes_invalid=0 send_seq=1302 receive_seq=1302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997742 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8701 bytes_read=26013 bytes_retransmit=9 bytes_invalid=0 send_seq=1297 receive_seq=1297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51777 bytes_read=634071 bytes_retransmit=0 bytes_invalid=0 send_seq=4934 receive_seq=4934 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998628 coil_temp=17.7 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=47.5 th1: temp=47.2 th2: temp=49.2 th3: temp=47.8 sysload=0.16 cputime=153.441 memavail=7404780 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 1199.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645729 bytes_read=1938481 bytes_retransmit=9 bytes_invalid=0 send_seq=300121 receive_seq=300121 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015690 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7954 bytes_read=26530 bytes_retransmit=0 bytes_invalid=0 send_seq=1297 receive_seq=1297 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998934 adj=49997016 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72592 bytes_read=2588840 bytes_retransmit=9 bytes_invalid=0 send_seq=10058 receive_seq=10058 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997670 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17046 bytes_read=148426 bytes_retransmit=9 bytes_invalid=0 send_seq=2040 receive_seq=2040 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997585 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8113 bytes_read=301908 bytes_retransmit=9 bytes_invalid=0 send_seq=1303 receive_seq=1303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997717 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8707 bytes_read=26029 bytes_retransmit=9 bytes_invalid=0 send_seq=1298 receive_seq=1298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51783 bytes_read=634427 bytes_retransmit=0 bytes_invalid=0 send_seq=4935 receive_seq=4935 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998641 coil_temp=17.7 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=47.3 th1: temp=47.1 th2: temp=49.0 th3: temp=47.7 sysload=0.16 cputime=153.476 memavail=7397988 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1200.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645735 bytes_read=1938613 bytes_retransmit=9 bytes_invalid=0 send_seq=300122 receive_seq=300122 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015686 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7960 bytes_read=26546 bytes_retransmit=0 bytes_invalid=0 send_seq=1298 receive_seq=1298 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998934 adj=49997028 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72598 bytes_read=2588940 bytes_retransmit=9 bytes_invalid=0 send_seq=10059 receive_seq=10059 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997674 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17052 bytes_read=148526 bytes_retransmit=9 bytes_invalid=0 send_seq=2041 receive_seq=2041 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8119 bytes_read=302142 bytes_retransmit=9 bytes_invalid=0 send_seq=1304 receive_seq=1304 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997700 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8713 bytes_read=26045 bytes_retransmit=9 bytes_invalid=0 send_seq=1299 receive_seq=1299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51789 bytes_read=634783 bytes_retransmit=0 bytes_invalid=0 send_seq=4936 receive_seq=4936 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998644 coil_temp=17.7 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=47.2 th1: temp=47.1 th2: temp=48.9 th3: temp=47.7 sysload=0.16 cputime=153.509 memavail=7403888 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1201.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645741 bytes_read=1938712 bytes_retransmit=9 bytes_invalid=0 send_seq=300123 receive_seq=300123 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015690 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=7966 bytes_read=26562 bytes_retransmit=0 bytes_invalid=0 send_seq=1299 receive_seq=1299 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998934 adj=49997011 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72604 bytes_read=2589068 bytes_retransmit=9 bytes_invalid=0 send_seq=10060 receive_seq=10060 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997671 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17058 bytes_read=148654 bytes_retransmit=9 bytes_invalid=0 send_seq=2042 receive_seq=2042 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997569 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8125 bytes_read=302436 bytes_retransmit=9 bytes_invalid=0 send_seq=1305 receive_seq=1305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8719 bytes_read=26072 bytes_retransmit=9 bytes_invalid=0 send_seq=1300 receive_seq=1300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51795 bytes_read=635139 bytes_retransmit=0 bytes_invalid=0 send_seq=4937 receive_seq=4937 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998723 coil_temp=17.7 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.9 th2: temp=48.7 th3: temp=47.6 sysload=0.15 cputime=153.541 memavail=7403888 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 1202.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645747 bytes_read=1938842 bytes_retransmit=9 bytes_invalid=0 send_seq=300124 receive_seq=300124 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015692 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7972 bytes_read=26591 bytes_retransmit=0 bytes_invalid=0 send_seq=1300 receive_seq=1300 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998934 adj=49996997 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72610 bytes_read=2589182 bytes_retransmit=9 bytes_invalid=0 send_seq=10061 receive_seq=10061 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997653 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17064 bytes_read=148754 bytes_retransmit=9 bytes_invalid=0 send_seq=2043 receive_seq=2043 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997543 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8131 bytes_read=302670 bytes_retransmit=9 bytes_invalid=0 send_seq=1306 receive_seq=1306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8725 bytes_read=26088 bytes_retransmit=9 bytes_invalid=0 send_seq=1301 receive_seq=1301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51801 bytes_read=635495 bytes_retransmit=0 bytes_invalid=0 send_seq=4938 receive_seq=4938 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998818 coil_temp=17.7 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=46.8 th1: temp=46.8 th2: temp=48.7 th3: temp=47.6 sysload=0.15 cputime=153.574 memavail=7403644 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1203.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645753 bytes_read=1938945 bytes_retransmit=9 bytes_invalid=0 send_seq=300125 receive_seq=300125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015693 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7978 bytes_read=26607 bytes_retransmit=0 bytes_invalid=0 send_seq=1301 receive_seq=1301 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998934 adj=49996989 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72616 bytes_read=2589282 bytes_retransmit=9 bytes_invalid=0 send_seq=10062 receive_seq=10062 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997644 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17070 bytes_read=148854 bytes_retransmit=9 bytes_invalid=0 send_seq=2044 receive_seq=2044 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8137 bytes_read=302904 bytes_retransmit=9 bytes_invalid=0 send_seq=1307 receive_seq=1307 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8731 bytes_read=26104 bytes_retransmit=9 bytes_invalid=0 send_seq=1302 receive_seq=1302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51807 bytes_read=635851 bytes_retransmit=0 bytes_invalid=0 send_seq=4939 receive_seq=4939 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998752 coil_temp=17.7 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.7 th2: temp=48.5 th3: temp=47.5 sysload=0.15 cputime=153.605 memavail=7403644 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1204.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645759 bytes_read=1939048 bytes_retransmit=9 bytes_invalid=0 send_seq=300126 receive_seq=300126 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015689 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7984 bytes_read=26623 bytes_retransmit=0 bytes_invalid=0 send_seq=1302 receive_seq=1302 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998934 adj=49996986 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72622 bytes_read=2589410 bytes_retransmit=9 bytes_invalid=0 send_seq=10063 receive_seq=10063 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997657 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17076 bytes_read=148996 bytes_retransmit=9 bytes_invalid=0 send_seq=2045 receive_seq=2045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8143 bytes_read=303213 bytes_retransmit=9 bytes_invalid=0 send_seq=1308 receive_seq=1308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8737 bytes_read=26120 bytes_retransmit=9 bytes_invalid=0 send_seq=1303 receive_seq=1303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51813 bytes_read=636207 bytes_retransmit=0 bytes_invalid=0 send_seq=4940 receive_seq=4940 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998704 coil_temp=17.7 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.6 th2: temp=48.4 th3: temp=47.4 sysload=0.15 cputime=153.638 memavail=7403644 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1205.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645765 bytes_read=1939194 bytes_retransmit=9 bytes_invalid=0 send_seq=300127 receive_seq=300127 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015707 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7990 bytes_read=26639 bytes_retransmit=0 bytes_invalid=0 send_seq=1303 receive_seq=1303 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998934 adj=49996991 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72628 bytes_read=2589510 bytes_retransmit=9 bytes_invalid=0 send_seq=10064 receive_seq=10064 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997656 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17082 bytes_read=149096 bytes_retransmit=9 bytes_invalid=0 send_seq=2046 receive_seq=2046 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8149 bytes_read=303447 bytes_retransmit=9 bytes_invalid=0 send_seq=1309 receive_seq=1309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997712 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8743 bytes_read=26136 bytes_retransmit=9 bytes_invalid=0 send_seq=1304 receive_seq=1304 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51819 bytes_read=636563 bytes_retransmit=0 bytes_invalid=0 send_seq=4941 receive_seq=4941 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998675 coil_temp=17.7 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=46.4 th1: temp=46.6 th2: temp=48.4 th3: temp=47.3 sysload=0.15 cputime=153.671 memavail=7403412 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1206.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645771 bytes_read=1939297 bytes_retransmit=9 bytes_invalid=0 send_seq=300128 receive_seq=300128 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015702 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=7996 bytes_read=26655 bytes_retransmit=0 bytes_invalid=0 send_seq=1304 receive_seq=1304 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998935 adj=49996953 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72634 bytes_read=2589610 bytes_retransmit=9 bytes_invalid=0 send_seq=10065 receive_seq=10065 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997610 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17088 bytes_read=149196 bytes_retransmit=9 bytes_invalid=0 send_seq=2047 receive_seq=2047 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997475 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8155 bytes_read=303681 bytes_retransmit=9 bytes_invalid=0 send_seq=1310 receive_seq=1310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8749 bytes_read=26163 bytes_retransmit=9 bytes_invalid=0 send_seq=1305 receive_seq=1305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51825 bytes_read=636919 bytes_retransmit=0 bytes_invalid=0 send_seq=4942 receive_seq=4942 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998637 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=46.3 th1: temp=46.5 th2: temp=48.4 th3: temp=47.3 sysload=0.14 cputime=153.703 memavail=7403412 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1207.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645777 bytes_read=1939400 bytes_retransmit=9 bytes_invalid=0 send_seq=300129 receive_seq=300129 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015698 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=8002 bytes_read=26684 bytes_retransmit=0 bytes_invalid=0 send_seq=1305 receive_seq=1305 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998938 adj=49996978 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72640 bytes_read=2589752 bytes_retransmit=9 bytes_invalid=0 send_seq=10066 receive_seq=10066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997628 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17094 bytes_read=149324 bytes_retransmit=9 bytes_invalid=0 send_seq=2048 receive_seq=2048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8161 bytes_read=303975 bytes_retransmit=9 bytes_invalid=0 send_seq=1311 receive_seq=1311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8755 bytes_read=26179 bytes_retransmit=9 bytes_invalid=0 send_seq=1306 receive_seq=1306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51831 bytes_read=637275 bytes_retransmit=0 bytes_invalid=0 send_seq=4943 receive_seq=4943 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998654 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=46.2 th1: temp=46.3 th2: temp=48.2 th3: temp=47.2 sysload=0.14 cputime=153.735 memavail=7403412 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 1208.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645783 bytes_read=1939532 bytes_retransmit=9 bytes_invalid=0 send_seq=300130 receive_seq=300130 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015696 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=8008 bytes_read=26700 bytes_retransmit=0 bytes_invalid=0 send_seq=1306 receive_seq=1306 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998937 adj=49997032 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72646 bytes_read=2589852 bytes_retransmit=9 bytes_invalid=0 send_seq=10067 receive_seq=10067 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997636 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17100 bytes_read=149424 bytes_retransmit=9 bytes_invalid=0 send_seq=2049 receive_seq=2049 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997522 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8167 bytes_read=304209 bytes_retransmit=9 bytes_invalid=0 send_seq=1312 receive_seq=1312 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8761 bytes_read=26195 bytes_retransmit=9 bytes_invalid=0 send_seq=1307 receive_seq=1307 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51837 bytes_read=637631 bytes_retransmit=0 bytes_invalid=0 send_seq=4944 receive_seq=4944 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998651 coil_temp=17.7 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=46.1 th1: temp=46.2 th2: temp=48.1 th3: temp=47.1 sysload=0.14 cputime=153.767 memavail=7403412 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1209.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645789 bytes_read=1939635 bytes_retransmit=9 bytes_invalid=0 send_seq=300131 receive_seq=300131 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015692 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=8014 bytes_read=26716 bytes_retransmit=0 bytes_invalid=0 send_seq=1307 receive_seq=1307 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998937 adj=49997003 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72652 bytes_read=2589952 bytes_retransmit=9 bytes_invalid=0 send_seq=10068 receive_seq=10068 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997666 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17106 bytes_read=149538 bytes_retransmit=9 bytes_invalid=0 send_seq=2050 receive_seq=2050 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997518 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8173 bytes_read=304458 bytes_retransmit=9 bytes_invalid=0 send_seq=1313 receive_seq=1313 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8767 bytes_read=26211 bytes_retransmit=9 bytes_invalid=0 send_seq=1308 receive_seq=1308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51843 bytes_read=637987 bytes_retransmit=0 bytes_invalid=0 send_seq=4945 receive_seq=4945 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998667 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=46.0 th1: temp=46.2 th2: temp=48.1 th3: temp=47.1 sysload=0.14 cputime=153.797 memavail=7403412 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1210.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645795 bytes_read=1939752 bytes_retransmit=9 bytes_invalid=0 send_seq=300132 receive_seq=300132 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015690 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=8020 bytes_read=26732 bytes_retransmit=0 bytes_invalid=0 send_seq=1308 receive_seq=1308 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998939 adj=49997008 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72658 bytes_read=2590080 bytes_retransmit=9 bytes_invalid=0 send_seq=10069 receive_seq=10069 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000187 adj=63997677 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17112 bytes_read=149666 bytes_retransmit=9 bytes_invalid=0 send_seq=2051 receive_seq=2051 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8179 bytes_read=304752 bytes_retransmit=9 bytes_invalid=0 send_seq=1314 receive_seq=1314 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8773 bytes_read=26227 bytes_retransmit=9 bytes_invalid=0 send_seq=1309 receive_seq=1309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51849 bytes_read=638343 bytes_retransmit=0 bytes_invalid=0 send_seq=4946 receive_seq=4946 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998688 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=45.9 th1: temp=46.2 th2: temp=47.9 th3: temp=47.0 sysload=0.14 cputime=153.830 memavail=7403412 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1211.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645801 bytes_read=1939884 bytes_retransmit=9 bytes_invalid=0 send_seq=300133 receive_seq=300133 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015687 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=8026 bytes_read=26747 bytes_retransmit=0 bytes_invalid=0 send_seq=1309 receive_seq=1309 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998939 adj=49997035 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72664 bytes_read=2590180 bytes_retransmit=9 bytes_invalid=0 send_seq=10070 receive_seq=10070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997677 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17118 bytes_read=149766 bytes_retransmit=9 bytes_invalid=0 send_seq=2052 receive_seq=2052 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997521 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8185 bytes_read=304986 bytes_retransmit=9 bytes_invalid=0 send_seq=1315 receive_seq=1315 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8779 bytes_read=26254 bytes_retransmit=9 bytes_invalid=0 send_seq=1310 receive_seq=1310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51855 bytes_read=638699 bytes_retransmit=0 bytes_invalid=0 send_seq=4947 receive_seq=4947 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998676 coil_temp=17.7 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=45.8 th1: temp=46.0 th2: temp=47.9 th3: temp=47.0 sysload=0.13 cputime=153.863 memavail=7403412 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1212.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645807 bytes_read=1939983 bytes_retransmit=9 bytes_invalid=0 send_seq=300134 receive_seq=300134 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015686 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=8032 bytes_read=26775 bytes_retransmit=0 bytes_invalid=0 send_seq=1310 receive_seq=1310 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998939 adj=49997024 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72670 bytes_read=2590294 bytes_retransmit=9 bytes_invalid=0 send_seq=10071 receive_seq=10071 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000186 adj=63997670 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17124 bytes_read=149866 bytes_retransmit=9 bytes_invalid=0 send_seq=2053 receive_seq=2053 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997521 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8217 bytes_read=305230 bytes_retransmit=9 bytes_invalid=0 send_seq=1318 receive_seq=1318 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8785 bytes_read=26270 bytes_retransmit=9 bytes_invalid=0 send_seq=1311 receive_seq=1311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51861 bytes_read=639055 bytes_retransmit=0 bytes_invalid=0 send_seq=4948 receive_seq=4948 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998654 coil_temp=17.7 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=45.8 th1: temp=46.0 th2: temp=47.8 th3: temp=47.0 sysload=0.13 cputime=153.896 memavail=7403412 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1213.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645813 bytes_read=1940086 bytes_retransmit=9 bytes_invalid=0 send_seq=300135 receive_seq=300135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015686 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=8038 bytes_read=26790 bytes_retransmit=0 bytes_invalid=0 send_seq=1311 receive_seq=1311 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998938 adj=49997015 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72676 bytes_read=2590422 bytes_retransmit=9 bytes_invalid=0 send_seq=10072 receive_seq=10072 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997669 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17130 bytes_read=149994 bytes_retransmit=9 bytes_invalid=0 send_seq=2054 receive_seq=2054 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8223 bytes_read=305524 bytes_retransmit=9 bytes_invalid=0 send_seq=1319 receive_seq=1319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8791 bytes_read=26286 bytes_retransmit=9 bytes_invalid=0 send_seq=1312 receive_seq=1312 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51867 bytes_read=639411 bytes_retransmit=0 bytes_invalid=0 send_seq=4949 receive_seq=4949 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998636 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=45.7 th1: temp=45.9 th2: temp=47.7 th3: temp=46.8 sysload=0.13 cputime=153.929 memavail=7403412 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1214.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645819 bytes_read=1940218 bytes_retransmit=9 bytes_invalid=0 send_seq=300136 receive_seq=300136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015688 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=8044 bytes_read=26805 bytes_retransmit=0 bytes_invalid=0 send_seq=1312 receive_seq=1312 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998938 adj=49996996 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72682 bytes_read=2590522 bytes_retransmit=9 bytes_invalid=0 send_seq=10073 receive_seq=10073 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997663 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=17136 bytes_read=150108 bytes_retransmit=9 bytes_invalid=0 send_seq=2055 receive_seq=2055 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997515 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8229 bytes_read=305773 bytes_retransmit=9 bytes_invalid=0 send_seq=1320 receive_seq=1320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8797 bytes_read=26302 bytes_retransmit=9 bytes_invalid=0 send_seq=1313 receive_seq=1313 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51873 bytes_read=639767 bytes_retransmit=0 bytes_invalid=0 send_seq=4950 receive_seq=4950 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998637 coil_temp=17.7 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=45.6 th1: temp=45.9 th2: temp=47.7 th3: temp=46.8 sysload=0.13 cputime=153.962 memavail=7403428 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1215.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645825 bytes_read=1940335 bytes_retransmit=9 bytes_invalid=0 send_seq=300137 receive_seq=300137 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015691 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=8050 bytes_read=26820 bytes_retransmit=0 bytes_invalid=0 send_seq=1313 receive_seq=1313 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998938 adj=49996982 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72688 bytes_read=2590622 bytes_retransmit=9 bytes_invalid=0 send_seq=10074 receive_seq=10074 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997657 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=17142 bytes_read=150208 bytes_retransmit=9 bytes_invalid=0 send_seq=2056 receive_seq=2056 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997522 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8235 bytes_read=306007 bytes_retransmit=9 bytes_invalid=0 send_seq=1321 receive_seq=1321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997679 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8803 bytes_read=26318 bytes_retransmit=9 bytes_invalid=0 send_seq=1314 receive_seq=1314 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51879 bytes_read=640123 bytes_retransmit=0 bytes_invalid=0 send_seq=4951 receive_seq=4951 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998635 coil_temp=17.7 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=45.5 th1: temp=45.8 th2: temp=47.7 th3: temp=46.7 sysload=0.13 cputime=153.993 memavail=7402720 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 1216.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645831 bytes_read=1940438 bytes_retransmit=9 bytes_invalid=0 send_seq=300138 receive_seq=300138 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015689 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=8056 bytes_read=26836 bytes_retransmit=0 bytes_invalid=0 send_seq=1314 receive_seq=1314 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998941 adj=49996973 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72694 bytes_read=2590750 bytes_retransmit=9 bytes_invalid=0 send_seq=10075 receive_seq=10075 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997650 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=17148 bytes_read=150336 bytes_retransmit=9 bytes_invalid=0 send_seq=2057 receive_seq=2057 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8241 bytes_read=306301 bytes_retransmit=9 bytes_invalid=0 send_seq=1322 receive_seq=1322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8809 bytes_read=26345 bytes_retransmit=9 bytes_invalid=0 send_seq=1315 receive_seq=1315 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51885 bytes_read=640479 bytes_retransmit=0 bytes_invalid=0 send_seq=4952 receive_seq=4952 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998628 coil_temp=17.7 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=45.5 th1: temp=45.6 th2: temp=47.6 th3: temp=46.7 sysload=0.12 cputime=154.026 memavail=7402720 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1217.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645837 bytes_read=1940570 bytes_retransmit=9 bytes_invalid=0 send_seq=300139 receive_seq=300139 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015694 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=8062 bytes_read=26865 bytes_retransmit=0 bytes_invalid=0 send_seq=1315 receive_seq=1315 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998942 adj=49997027 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72700 bytes_read=2590864 bytes_retransmit=9 bytes_invalid=0 send_seq=10076 receive_seq=10076 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997657 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=17154 bytes_read=150436 bytes_retransmit=9 bytes_invalid=0 send_seq=2058 receive_seq=2058 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8247 bytes_read=306535 bytes_retransmit=9 bytes_invalid=0 send_seq=1323 receive_seq=1323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8815 bytes_read=26361 bytes_retransmit=9 bytes_invalid=0 send_seq=1316 receive_seq=1316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51891 bytes_read=640835 bytes_retransmit=0 bytes_invalid=0 send_seq=4953 receive_seq=4953 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998625 coil_temp=17.7 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=45.3 th1: temp=45.6 th2: temp=47.5 th3: temp=46.6 sysload=0.12 cputime=154.063 memavail=7403872 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 1218.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645843 bytes_read=1940673 bytes_retransmit=9 bytes_invalid=0 send_seq=300140 receive_seq=300140 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015693 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=8068 bytes_read=26881 bytes_retransmit=0 bytes_invalid=0 send_seq=1316 receive_seq=1316 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998942 adj=49997023 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72706 bytes_read=2590964 bytes_retransmit=9 bytes_invalid=0 send_seq=10077 receive_seq=10077 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000184 adj=63997645 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=17160 bytes_read=150536 bytes_retransmit=9 bytes_invalid=0 send_seq=2059 receive_seq=2059 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8253 bytes_read=306769 bytes_retransmit=9 bytes_invalid=0 send_seq=1324 receive_seq=1324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8821 bytes_read=26377 bytes_retransmit=9 bytes_invalid=0 send_seq=1317 receive_seq=1317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51897 bytes_read=641191 bytes_retransmit=0 bytes_invalid=0 send_seq=4954 receive_seq=4954 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998618 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=45.2 th1: temp=45.6 th2: temp=47.5 th3: temp=46.6 sysload=0.12 cputime=154.095 memavail=7403872 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1219.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645849 bytes_read=1940776 bytes_retransmit=9 bytes_invalid=0 send_seq=300141 receive_seq=300141 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015694 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=8074 bytes_read=26897 bytes_retransmit=0 bytes_invalid=0 send_seq=1317 receive_seq=1317 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998941 adj=49997014 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72712 bytes_read=2591092 bytes_retransmit=9 bytes_invalid=0 send_seq=10078 receive_seq=10078 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000185 adj=63997655 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17166 bytes_read=150678 bytes_retransmit=9 bytes_invalid=0 send_seq=2060 receive_seq=2060 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8259 bytes_read=307078 bytes_retransmit=9 bytes_invalid=0 send_seq=1325 receive_seq=1325 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8827 bytes_read=26393 bytes_retransmit=9 bytes_invalid=0 send_seq=1318 receive_seq=1318 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51903 bytes_read=641547 bytes_retransmit=0 bytes_invalid=0 send_seq=4955 receive_seq=4955 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998617 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=45.2 th1: temp=45.5 th2: temp=47.4 th3: temp=46.4 sysload=0.12 cputime=154.128 memavail=7403872 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1220.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645855 bytes_read=1940922 bytes_retransmit=9 bytes_invalid=0 send_seq=300142 receive_seq=300142 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015700 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=8080 bytes_read=26913 bytes_retransmit=0 bytes_invalid=0 send_seq=1318 receive_seq=1318 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998941 adj=49996997 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72718 bytes_read=2591192 bytes_retransmit=9 bytes_invalid=0 send_seq=10079 receive_seq=10079 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997665 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17172 bytes_read=150778 bytes_retransmit=9 bytes_invalid=0 send_seq=2061 receive_seq=2061 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997503 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8265 bytes_read=307312 bytes_retransmit=9 bytes_invalid=0 send_seq=1326 receive_seq=1326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8833 bytes_read=26409 bytes_retransmit=9 bytes_invalid=0 send_seq=1319 receive_seq=1319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51909 bytes_read=641903 bytes_retransmit=0 bytes_invalid=0 send_seq=4956 receive_seq=4956 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998672 coil_temp=17.7 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=45.1 th1: temp=45.4 th2: temp=47.3 th3: temp=46.5 sysload=0.12 cputime=154.160 memavail=7403872 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 1221.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645861 bytes_read=1941025 bytes_retransmit=9 bytes_invalid=0 send_seq=300143 receive_seq=300143 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015709 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=8086 bytes_read=26929 bytes_retransmit=0 bytes_invalid=0 send_seq=1319 receive_seq=1319 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998941 adj=49996976 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72724 bytes_read=2591292 bytes_retransmit=9 bytes_invalid=0 send_seq=10080 receive_seq=10080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997738 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17178 bytes_read=150878 bytes_retransmit=9 bytes_invalid=0 send_seq=2062 receive_seq=2062 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997617 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8271 bytes_read=307546 bytes_retransmit=9 bytes_invalid=0 send_seq=1327 receive_seq=1327 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8839 bytes_read=26436 bytes_retransmit=9 bytes_invalid=0 send_seq=1320 receive_seq=1320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51915 bytes_read=642259 bytes_retransmit=0 bytes_invalid=0 send_seq=4957 receive_seq=4957 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998650 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=44.9 th1: temp=45.4 th2: temp=47.2 th3: temp=46.4 sysload=0.11 cputime=154.191 memavail=7403872 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 1222.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645867 bytes_read=1941128 bytes_retransmit=9 bytes_invalid=0 send_seq=300144 receive_seq=300144 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015710 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=8092 bytes_read=26958 bytes_retransmit=0 bytes_invalid=0 send_seq=1320 receive_seq=1320 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998942 adj=49996956 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72730 bytes_read=2591434 bytes_retransmit=9 bytes_invalid=0 send_seq=10081 receive_seq=10081 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997694 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17184 bytes_read=151006 bytes_retransmit=9 bytes_invalid=0 send_seq=2063 receive_seq=2063 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8277 bytes_read=307840 bytes_retransmit=9 bytes_invalid=0 send_seq=1328 receive_seq=1328 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8845 bytes_read=26452 bytes_retransmit=9 bytes_invalid=0 send_seq=1321 receive_seq=1321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999432 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51921 bytes_read=642615 bytes_retransmit=0 bytes_invalid=0 send_seq=4958 receive_seq=4958 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998639 coil_temp=17.7 refs=0 mcu_temp=20.91 supply_voltage=3.012 th0: temp=45.0 th1: temp=45.4 th2: temp=47.3 th3: temp=46.4 sysload=0.11 cputime=154.223 memavail=7403648 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 1223.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645873 bytes_read=1941255 bytes_retransmit=9 bytes_invalid=0 send_seq=300145 receive_seq=300145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015710 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=8098 bytes_read=26974 bytes_retransmit=0 bytes_invalid=0 send_seq=1321 receive_seq=1321 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998943 adj=49996973 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72736 bytes_read=2591534 bytes_retransmit=9 bytes_invalid=0 send_seq=10082 receive_seq=10082 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997679 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17190 bytes_read=151106 bytes_retransmit=9 bytes_invalid=0 send_seq=2064 receive_seq=2064 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997549 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8283 bytes_read=308074 bytes_retransmit=9 bytes_invalid=0 send_seq=1329 receive_seq=1329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997740 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8851 bytes_read=26468 bytes_retransmit=9 bytes_invalid=0 send_seq=1322 receive_seq=1322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999433 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51927 bytes_read=642971 bytes_retransmit=0 bytes_invalid=0 send_seq=4959 receive_seq=4959 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998635 coil_temp=17.7 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=44.8 th1: temp=45.3 th2: temp=47.3 th3: temp=46.3 sysload=0.11 cputime=154.255 memavail=7403648 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1224.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645879 bytes_read=1941358 bytes_retransmit=9 bytes_invalid=0 send_seq=300146 receive_seq=300146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015710 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=8104 bytes_read=26990 bytes_retransmit=0 bytes_invalid=0 send_seq=1322 receive_seq=1322 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998942 adj=49996987 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72742 bytes_read=2591634 bytes_retransmit=9 bytes_invalid=0 send_seq=10083 receive_seq=10083 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997672 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17196 bytes_read=151220 bytes_retransmit=9 bytes_invalid=0 send_seq=2065 receive_seq=2065 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8289 bytes_read=308323 bytes_retransmit=9 bytes_invalid=0 send_seq=1330 receive_seq=1330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997706 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8857 bytes_read=26484 bytes_retransmit=9 bytes_invalid=0 send_seq=1323 receive_seq=1323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999436 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51933 bytes_read=643327 bytes_retransmit=0 bytes_invalid=0 send_seq=4960 receive_seq=4960 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998626 coil_temp=17.7 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=44.8 th1: temp=45.2 th2: temp=47.1 th3: temp=46.4 sysload=0.11 cputime=154.286 memavail=7403648 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1225.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645885 bytes_read=1941461 bytes_retransmit=9 bytes_invalid=0 send_seq=300147 receive_seq=300147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015737 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=8110 bytes_read=27006 bytes_retransmit=0 bytes_invalid=0 send_seq=1323 receive_seq=1323 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998943 adj=49996981 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72748 bytes_read=2591762 bytes_retransmit=9 bytes_invalid=0 send_seq=10084 receive_seq=10084 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997675 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17202 bytes_read=151348 bytes_retransmit=9 bytes_invalid=0 send_seq=2066 receive_seq=2066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8295 bytes_read=308617 bytes_retransmit=9 bytes_invalid=0 send_seq=1331 receive_seq=1331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8863 bytes_read=26500 bytes_retransmit=9 bytes_invalid=0 send_seq=1324 receive_seq=1324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51939 bytes_read=643683 bytes_retransmit=0 bytes_invalid=0 send_seq=4961 receive_seq=4961 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998628 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=44.8 th1: temp=45.3 th2: temp=47.1 th3: temp=46.3 sysload=0.11 cputime=154.318 memavail=7402648 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1226.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645891 bytes_read=1941607 bytes_retransmit=9 bytes_invalid=0 send_seq=300148 receive_seq=300148 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015760 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=8116 bytes_read=27022 bytes_retransmit=0 bytes_invalid=0 send_seq=1324 receive_seq=1324 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998947 adj=49996944 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72754 bytes_read=2591862 bytes_retransmit=9 bytes_invalid=0 send_seq=10085 receive_seq=10085 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997736 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17208 bytes_read=151448 bytes_retransmit=9 bytes_invalid=0 send_seq=2067 receive_seq=2067 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997454 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8301 bytes_read=308851 bytes_retransmit=9 bytes_invalid=0 send_seq=1332 receive_seq=1332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997623 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8869 bytes_read=26527 bytes_retransmit=9 bytes_invalid=0 send_seq=1325 receive_seq=1325 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999426 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51945 bytes_read=644039 bytes_retransmit=0 bytes_invalid=0 send_seq=4962 receive_seq=4962 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998596 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=44.7 th1: temp=45.1 th2: temp=47.1 th3: temp=46.2 sysload=0.10 cputime=154.351 memavail=7402668 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 1227.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645903 bytes_read=1941726 bytes_retransmit=9 bytes_invalid=0 send_seq=300150 receive_seq=300150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015791 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=8128 bytes_read=27067 bytes_retransmit=0 bytes_invalid=0 send_seq=1326 receive_seq=1326 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998952 adj=49996961 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72766 bytes_read=2591992 bytes_retransmit=9 bytes_invalid=0 send_seq=10087 receive_seq=10087 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997674 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17220 bytes_read=151564 bytes_retransmit=9 bytes_invalid=0 send_seq=2069 receive_seq=2069 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997407 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8313 bytes_read=309101 bytes_retransmit=9 bytes_invalid=0 send_seq=1334 receive_seq=1334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997584 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8881 bytes_read=26559 bytes_retransmit=9 bytes_invalid=0 send_seq=1327 receive_seq=1327 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999419 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51957 bytes_read=644411 bytes_retransmit=0 bytes_invalid=0 send_seq=4964 receive_seq=4964 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998576 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=44.7 th1: temp=45.1 th2: temp=47.0 th3: temp=46.2 sysload=0.10 cputime=154.384 memavail=7402672 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 1228.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645909 bytes_read=1941829 bytes_retransmit=9 bytes_invalid=0 send_seq=300151 receive_seq=300151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015814 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=8134 bytes_read=27083 bytes_retransmit=0 bytes_invalid=0 send_seq=1327 receive_seq=1327 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998956 adj=49996986 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72772 bytes_read=2592120 bytes_retransmit=9 bytes_invalid=0 send_seq=10088 receive_seq=10088 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997682 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17226 bytes_read=151692 bytes_retransmit=9 bytes_invalid=0 send_seq=2070 receive_seq=2070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997337 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8319 bytes_read=309386 bytes_retransmit=9 bytes_invalid=0 send_seq=1335 receive_seq=1335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997581 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8887 bytes_read=26575 bytes_retransmit=9 bytes_invalid=0 send_seq=1328 receive_seq=1328 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999410 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51963 bytes_read=644767 bytes_retransmit=0 bytes_invalid=0 send_seq=4965 receive_seq=4965 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998543 coil_temp=17.7 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=44.7 th1: temp=45.0 th2: temp=47.0 th3: temp=46.1 sysload=0.10 cputime=154.416 memavail=7402672 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 1229.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645915 bytes_read=1941961 bytes_retransmit=9 bytes_invalid=0 send_seq=300152 receive_seq=300152 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015809 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=8140 bytes_read=27099 bytes_retransmit=0 bytes_invalid=0 send_seq=1328 receive_seq=1328 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998956 adj=49996998 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72778 bytes_read=2592220 bytes_retransmit=9 bytes_invalid=0 send_seq=10089 receive_seq=10089 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997628 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17232 bytes_read=151806 bytes_retransmit=9 bytes_invalid=0 send_seq=2071 receive_seq=2071 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997315 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8325 bytes_read=309620 bytes_retransmit=9 bytes_invalid=0 send_seq=1336 receive_seq=1336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997541 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8893 bytes_read=26591 bytes_retransmit=9 bytes_invalid=0 send_seq=1329 receive_seq=1329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999405 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51969 bytes_read=645123 bytes_retransmit=0 bytes_invalid=0 send_seq=4966 receive_seq=4966 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999909 adj=31998535 coil_temp=17.7 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=44.6 th1: temp=44.9 th2: temp=47.0 th3: temp=46.1 sysload=0.10 cputime=154.449 memavail=7402672 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 1230.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645921 bytes_read=1942064 bytes_retransmit=9 bytes_invalid=0 send_seq=300153 receive_seq=300153 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015809 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=8146 bytes_read=27115 bytes_retransmit=0 bytes_invalid=0 send_seq=1329 receive_seq=1329 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998957 adj=49997012 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72784 bytes_read=2592320 bytes_retransmit=9 bytes_invalid=0 send_seq=10090 receive_seq=10090 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997630 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17238 bytes_read=151906 bytes_retransmit=9 bytes_invalid=0 send_seq=2072 receive_seq=2072 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997364 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8331 bytes_read=309839 bytes_retransmit=9 bytes_invalid=0 send_seq=1337 receive_seq=1337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997573 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8899 bytes_read=26607 bytes_retransmit=9 bytes_invalid=0 send_seq=1330 receive_seq=1330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999418 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51975 bytes_read=645479 bytes_retransmit=0 bytes_invalid=0 send_seq=4967 receive_seq=4967 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998553 coil_temp=17.7 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=44.5 th1: temp=45.0 th2: temp=46.9 th3: temp=46.0 sysload=0.10 cputime=154.485 memavail=7404372 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 1231.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645927 bytes_read=1942181 bytes_retransmit=9 bytes_invalid=0 send_seq=300154 receive_seq=300154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015804 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=8152 bytes_read=27131 bytes_retransmit=0 bytes_invalid=0 send_seq=1330 receive_seq=1330 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998957 adj=49997020 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72790 bytes_read=2592448 bytes_retransmit=9 bytes_invalid=0 send_seq=10091 receive_seq=10091 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997622 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17244 bytes_read=152034 bytes_retransmit=9 bytes_invalid=0 send_seq=2073 receive_seq=2073 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997400 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8337 bytes_read=310114 bytes_retransmit=9 bytes_invalid=0 send_seq=1338 receive_seq=1338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997578 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8905 bytes_read=26634 bytes_retransmit=9 bytes_invalid=0 send_seq=1331 receive_seq=1331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999424 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51981 bytes_read=645835 bytes_retransmit=0 bytes_invalid=0 send_seq=4968 receive_seq=4968 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998569 coil_temp=17.7 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=44.4 th1: temp=45.0 th2: temp=46.9 th3: temp=46.0 sysload=0.09 cputime=154.518 memavail=7404460 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1232.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645933 bytes_read=1942313 bytes_retransmit=9 bytes_invalid=0 send_seq=300155 receive_seq=300155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015799 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=8158 bytes_read=27160 bytes_retransmit=0 bytes_invalid=0 send_seq=1331 receive_seq=1331 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998958 adj=49997019 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72796 bytes_read=2592562 bytes_retransmit=9 bytes_invalid=0 send_seq=10092 receive_seq=10092 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997630 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17250 bytes_read=152134 bytes_retransmit=9 bytes_invalid=0 send_seq=2074 receive_seq=2074 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997430 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8343 bytes_read=310333 bytes_retransmit=9 bytes_invalid=0 send_seq=1339 receive_seq=1339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997595 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8911 bytes_read=26650 bytes_retransmit=9 bytes_invalid=0 send_seq=1332 receive_seq=1332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999431 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51987 bytes_read=646191 bytes_retransmit=0 bytes_invalid=0 send_seq=4969 receive_seq=4969 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998599 coil_temp=17.7 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=44.4 th1: temp=44.9 th2: temp=46.8 th3: temp=46.0 sysload=0.09 cputime=154.551 memavail=7404464 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1233.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645939 bytes_read=1942414 bytes_retransmit=9 bytes_invalid=0 send_seq=300156 receive_seq=300156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015794 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=8164 bytes_read=27176 bytes_retransmit=0 bytes_invalid=0 send_seq=1332 receive_seq=1332 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998957 adj=49997026 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72802 bytes_read=2592662 bytes_retransmit=9 bytes_invalid=0 send_seq=10093 receive_seq=10093 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997632 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17256 bytes_read=152234 bytes_retransmit=9 bytes_invalid=0 send_seq=2075 receive_seq=2075 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997463 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8349 bytes_read=310552 bytes_retransmit=9 bytes_invalid=0 send_seq=1340 receive_seq=1340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997603 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8917 bytes_read=26666 bytes_retransmit=9 bytes_invalid=0 send_seq=1333 receive_seq=1333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51993 bytes_read=646547 bytes_retransmit=0 bytes_invalid=0 send_seq=4970 receive_seq=4970 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998604 coil_temp=17.8 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=44.4 th1: temp=44.9 th2: temp=46.8 th3: temp=46.0 sysload=0.09 cputime=154.583 memavail=7404464 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1234.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645945 bytes_read=1942515 bytes_retransmit=9 bytes_invalid=0 send_seq=300157 receive_seq=300157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015791 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=8170 bytes_read=27192 bytes_retransmit=0 bytes_invalid=0 send_seq=1333 receive_seq=1333 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998959 adj=49997016 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72808 bytes_read=2592790 bytes_retransmit=9 bytes_invalid=0 send_seq=10094 receive_seq=10094 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997636 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17262 bytes_read=152376 bytes_retransmit=9 bytes_invalid=0 send_seq=2076 receive_seq=2076 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997484 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=8355 bytes_read=310855 bytes_retransmit=9 bytes_invalid=0 send_seq=1341 receive_seq=1341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8923 bytes_read=26682 bytes_retransmit=9 bytes_invalid=0 send_seq=1334 receive_seq=1334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999439 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=51999 bytes_read=646903 bytes_retransmit=0 bytes_invalid=0 send_seq=4971 receive_seq=4971 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998617 coil_temp=17.8 refs=0 mcu_temp=20.97 supply_voltage=3.012 th0: temp=44.3 th1: temp=44.8 th2: temp=46.7 th3: temp=46.0 sysload=0.09 cputime=154.620 memavail=7405080 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 1235.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645951 bytes_read=1942647 bytes_retransmit=9 bytes_invalid=0 send_seq=300158 receive_seq=300158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015787 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=8176 bytes_read=27208 bytes_retransmit=0 bytes_invalid=0 send_seq=1334 receive_seq=1334 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998959 adj=49997039 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72814 bytes_read=2592890 bytes_retransmit=9 bytes_invalid=0 send_seq=10095 receive_seq=10095 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997637 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17268 bytes_read=152476 bytes_retransmit=9 bytes_invalid=0 send_seq=2077 receive_seq=2077 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=8361 bytes_read=311089 bytes_retransmit=9 bytes_invalid=0 send_seq=1342 receive_seq=1342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8929 bytes_read=26698 bytes_retransmit=9 bytes_invalid=0 send_seq=1335 receive_seq=1335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999442 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=52005 bytes_read=647259 bytes_retransmit=0 bytes_invalid=0 send_seq=4972 receive_seq=4972 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998627 coil_temp=17.8 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=44.4 th1: temp=44.8 th2: temp=46.7 th3: temp=45.9 sysload=0.09 cputime=154.652 memavail=7404076 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1236.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645957 bytes_read=1942764 bytes_retransmit=9 bytes_invalid=0 send_seq=300159 receive_seq=300159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015783 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=8182 bytes_read=27224 bytes_retransmit=0 bytes_invalid=0 send_seq=1335 receive_seq=1335 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998961 adj=49997036 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72820 bytes_read=2592990 bytes_retransmit=9 bytes_invalid=0 send_seq=10096 receive_seq=10096 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997643 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17274 bytes_read=152576 bytes_retransmit=9 bytes_invalid=0 send_seq=2078 receive_seq=2078 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=8367 bytes_read=311323 bytes_retransmit=9 bytes_invalid=0 send_seq=1343 receive_seq=1343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8935 bytes_read=26725 bytes_retransmit=9 bytes_invalid=0 send_seq=1336 receive_seq=1336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999447 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=52011 bytes_read=647615 bytes_retransmit=0 bytes_invalid=0 send_seq=4973 receive_seq=4973 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999907 adj=31998631 coil_temp=17.8 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=44.3 th1: temp=44.7 th2: temp=46.6 th3: temp=46.0 sysload=0.08 cputime=154.684 memavail=7404076 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 1237.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645963 bytes_read=1942867 bytes_retransmit=9 bytes_invalid=0 send_seq=300160 receive_seq=300160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015780 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=8188 bytes_read=27253 bytes_retransmit=0 bytes_invalid=0 send_seq=1336 receive_seq=1336 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998960 adj=49997066 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72826 bytes_read=2593132 bytes_retransmit=9 bytes_invalid=0 send_seq=10097 receive_seq=10097 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997657 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17280 bytes_read=152704 bytes_retransmit=9 bytes_invalid=0 send_seq=2079 receive_seq=2079 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997541 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=8373 bytes_read=311617 bytes_retransmit=9 bytes_invalid=0 send_seq=1344 receive_seq=1344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8941 bytes_read=26741 bytes_retransmit=9 bytes_invalid=0 send_seq=1337 receive_seq=1337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=52017 bytes_read=647971 bytes_retransmit=0 bytes_invalid=0 send_seq=4974 receive_seq=4974 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998632 coil_temp=17.8 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=44.3 th1: temp=44.7 th2: temp=46.6 th3: temp=46.0 sysload=0.08 cputime=154.717 memavail=7404080 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 1238.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645969 bytes_read=1942999 bytes_retransmit=9 bytes_invalid=0 send_seq=300161 receive_seq=300161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015779 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=8194 bytes_read=27269 bytes_retransmit=0 bytes_invalid=0 send_seq=1337 receive_seq=1337 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998960 adj=49997041 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72832 bytes_read=2593232 bytes_retransmit=9 bytes_invalid=0 send_seq=10098 receive_seq=10098 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997661 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17286 bytes_read=152804 bytes_retransmit=9 bytes_invalid=0 send_seq=2080 receive_seq=2080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997542 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=8379 bytes_read=311851 bytes_retransmit=9 bytes_invalid=0 send_seq=1345 receive_seq=1345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8947 bytes_read=26757 bytes_retransmit=9 bytes_invalid=0 send_seq=1338 receive_seq=1338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999447 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=52023 bytes_read=648327 bytes_retransmit=0 bytes_invalid=0 send_seq=4975 receive_seq=4975 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999905 adj=31998629 coil_temp=17.8 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=44.1 th1: temp=44.7 th2: temp=46.6 th3: temp=45.9 sysload=0.08 cputime=154.748 memavail=7404080 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 1239.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645975 bytes_read=1943102 bytes_retransmit=9 bytes_invalid=0 send_seq=300162 receive_seq=300162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015776 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=8200 bytes_read=27285 bytes_retransmit=0 bytes_invalid=0 send_seq=1338 receive_seq=1338 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998960 adj=49997026 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72838 bytes_read=2593332 bytes_retransmit=9 bytes_invalid=0 send_seq=10099 receive_seq=10099 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997658 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17292 bytes_read=152918 bytes_retransmit=9 bytes_invalid=0 send_seq=2081 receive_seq=2081 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8385 bytes_read=312100 bytes_retransmit=9 bytes_invalid=0 send_seq=1346 receive_seq=1346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8953 bytes_read=26773 bytes_retransmit=9 bytes_invalid=0 send_seq=1339 receive_seq=1339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999445 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=52029 bytes_read=648683 bytes_retransmit=0 bytes_invalid=0 send_seq=4976 receive_seq=4976 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999905 adj=31998624 coil_temp=17.8 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=44.2 th1: temp=44.6 th2: temp=46.5 th3: temp=45.8 sysload=0.08 cputime=154.780 memavail=7404084 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 1240.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645981 bytes_read=1943205 bytes_retransmit=9 bytes_invalid=0 send_seq=300163 receive_seq=300163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015772 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=8206 bytes_read=27301 bytes_retransmit=0 bytes_invalid=0 send_seq=1339 receive_seq=1339 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998962 adj=49997020 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72844 bytes_read=2593460 bytes_retransmit=9 bytes_invalid=0 send_seq=10100 receive_seq=10100 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997656 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17298 bytes_read=153046 bytes_retransmit=9 bytes_invalid=0 send_seq=2082 receive_seq=2082 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997526 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8391 bytes_read=312394 bytes_retransmit=9 bytes_invalid=0 send_seq=1347 receive_seq=1347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8959 bytes_read=26789 bytes_retransmit=9 bytes_invalid=0 send_seq=1340 receive_seq=1340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999444 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=52035 bytes_read=649039 bytes_retransmit=0 bytes_invalid=0 send_seq=4977 receive_seq=4977 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998622 coil_temp=17.8 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=44.1 th1: temp=44.6 th2: temp=46.5 th3: temp=45.8 sysload=0.08 cputime=154.813 memavail=7404096 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 1241.7: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17645987 bytes_read=1943351 bytes_retransmit=9 bytes_invalid=0 send_seq=300164 receive_seq=300164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015771 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=8212 bytes_read=27317 bytes_retransmit=0 bytes_invalid=0 send_seq=1340 receive_seq=1340 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998963 adj=49997057 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=72850 bytes_read=2593560 bytes_retransmit=9 bytes_invalid=0 send_seq=10101 receive_seq=10101 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997661 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=17304 bytes_read=153146 bytes_retransmit=9 bytes_invalid=0 send_seq=2083 receive_seq=2083 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997540 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=8397 bytes_read=312628 bytes_retransmit=9 bytes_invalid=0 send_seq=1348 receive_seq=1348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997742 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=8965 bytes_read=26816 bytes_retransmit=9 bytes_invalid=0 send_seq=1341 receive_seq=1341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=52041 bytes_read=649395 bytes_retransmit=0 bytes_invalid=0 send_seq=4978 receive_seq=4978 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998658 coil_temp=17.8 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=44.1 th1: temp=44.5 th2: temp=46.6 th3: temp=45.7 sysload=0.08 cputime=154.844 memavail=7404096 print_time=1204.303 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Extruder extruder already active
Extruder 'extruder' now syncing with 'extruder'
Extruder 'extruder1' now syncing with 'extruder1'
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 2032.2: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17652425 bytes_read=2035673 bytes_retransmit=9 bytes_invalid=0 send_seq=301042 receive_seq=301042 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400014978 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13030 bytes_read=42157 bytes_retransmit=0 bytes_invalid=0 send_seq=2143 receive_seq=2143 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999185 adj=49997324 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=77668 bytes_read=2681983 bytes_retransmit=9 bytes_invalid=0 send_seq=10904 receive_seq=10904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997802 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22122 bytes_read=241569 bytes_retransmit=9 bytes_invalid=0 send_seq=2886 receive_seq=2886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997663 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13215 bytes_read=515230 bytes_retransmit=9 bytes_invalid=0 send_seq=2151 receive_seq=2151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997747 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13783 bytes_read=41356 bytes_retransmit=9 bytes_invalid=0 send_seq=2144 receive_seq=2144 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999467 Octopus_Pro_H723_V1.1: temp=36.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56859 bytes_read=930165 bytes_retransmit=0 bytes_invalid=0 send_seq=5781 receive_seq=5781 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998733 coil_temp=18.1 refs=0 mcu_temp=20.99 supply_voltage=3.012 th0: temp=36.6 th1: temp=36.9 th2: temp=38.8 th3: temp=38.3 sysload=0.00 cputime=180.067 memavail=7402508 print_time=2055.304 buffer_time=0.636 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2033.2: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17655224 bytes_read=2038014 bytes_retransmit=9 bytes_invalid=0 send_seq=301227 receive_seq=301227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400014972 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13036 bytes_read=42173 bytes_retransmit=0 bytes_invalid=0 send_seq=2144 receive_seq=2144 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999185 adj=49997316 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=77674 bytes_read=2682083 bytes_retransmit=9 bytes_invalid=0 send_seq=10905 receive_seq=10905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997801 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22128 bytes_read=241669 bytes_retransmit=9 bytes_invalid=0 send_seq=2887 receive_seq=2887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997655 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13249 bytes_read=515474 bytes_retransmit=9 bytes_invalid=0 send_seq=2154 receive_seq=2154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997733 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13789 bytes_read=41372 bytes_retransmit=9 bytes_invalid=0 send_seq=2145 receive_seq=2145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999471 Octopus_Pro_H723_V1.1: temp=36.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56865 bytes_read=930521 bytes_retransmit=0 bytes_invalid=0 send_seq=5782 receive_seq=5782 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998723 coil_temp=18.1 refs=0 mcu_temp=20.99 supply_voltage=3.012 th0: temp=36.6 th1: temp=36.9 th2: temp=38.8 th3: temp=38.3 sysload=0.00 cputime=180.158 memavail=7402508 print_time=2055.838 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2034.2: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=17656430 bytes_read=2038805 bytes_retransmit=9 bytes_invalid=0 send_seq=301284 receive_seq=301284 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400014967 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13042 bytes_read=42189 bytes_retransmit=0 bytes_invalid=0 send_seq=2145 receive_seq=2145 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999185 adj=49997324 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=77680 bytes_read=2682225 bytes_retransmit=9 bytes_invalid=0 send_seq=10906 receive_seq=10906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997807 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22134 bytes_read=241797 bytes_retransmit=9 bytes_invalid=0 send_seq=2888 receive_seq=2888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997679 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13255 bytes_read=515755 bytes_retransmit=9 bytes_invalid=0 send_seq=2155 receive_seq=2155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997740 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13795 bytes_read=41388 bytes_retransmit=9 bytes_invalid=0 send_seq=2146 receive_seq=2146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999482 Octopus_Pro_H723_V1.1: temp=36.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56871 bytes_read=930877 bytes_retransmit=0 bytes_invalid=0 send_seq=5783 receive_seq=5783 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998736 coil_temp=18.1 refs=0 mcu_temp=21.00 supply_voltage=3.012 th0: temp=37.5 th1: temp=37.4 th2: temp=39.7 th3: temp=38.9 sysload=0.00 cputime=180.221 memavail=7402508 print_time=2056.838 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2035.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=17657661 bytes_read=2039627 bytes_retransmit=9 bytes_invalid=0 send_seq=301341 receive_seq=301341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400014959 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13048 bytes_read=42205 bytes_retransmit=0 bytes_invalid=0 send_seq=2146 receive_seq=2146 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999184 adj=49997328 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=77686 bytes_read=2682325 bytes_retransmit=9 bytes_invalid=0 send_seq=10907 receive_seq=10907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997810 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22140 bytes_read=241897 bytes_retransmit=9 bytes_invalid=0 send_seq=2889 receive_seq=2889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997674 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13261 bytes_read=515988 bytes_retransmit=9 bytes_invalid=0 send_seq=2156 receive_seq=2156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997734 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13801 bytes_read=41404 bytes_retransmit=9 bytes_invalid=0 send_seq=2147 receive_seq=2147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999478 Octopus_Pro_H723_V1.1: temp=36.5 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56877 bytes_read=931233 bytes_retransmit=0 bytes_invalid=0 send_seq=5784 receive_seq=5784 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998733 coil_temp=18.1 refs=0 mcu_temp=21.01 supply_voltage=3.012 th0: temp=37.4 th1: temp=37.6 th2: temp=39.5 th3: temp=39.0 sysload=0.00 cputime=180.283 memavail=7402508 print_time=2057.888 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2036.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=17658855 bytes_read=2040399 bytes_retransmit=9 bytes_invalid=0 send_seq=301397 receive_seq=301397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400014955 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13054 bytes_read=42234 bytes_retransmit=0 bytes_invalid=0 send_seq=2147 receive_seq=2147 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999186 adj=49997185 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=77692 bytes_read=2682425 bytes_retransmit=9 bytes_invalid=0 send_seq=10908 receive_seq=10908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997640 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22146 bytes_read=242011 bytes_retransmit=9 bytes_invalid=0 send_seq=2890 receive_seq=2890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997493 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13267 bytes_read=516206 bytes_retransmit=9 bytes_invalid=0 send_seq=2157 receive_seq=2157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997593 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13807 bytes_read=41420 bytes_retransmit=9 bytes_invalid=0 send_seq=2148 receive_seq=2148 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999441 Octopus_Pro_H723_V1.1: temp=36.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56883 bytes_read=931589 bytes_retransmit=0 bytes_invalid=0 send_seq=5785 receive_seq=5785 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998640 coil_temp=18.1 refs=0 mcu_temp=20.99 supply_voltage=3.012 th0: temp=37.4 th1: temp=37.1 th2: temp=39.8 th3: temp=38.6 sysload=0.00 cputime=180.344 memavail=7401792 print_time=2058.888 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 2037.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=17660056 bytes_read=2041185 bytes_retransmit=9 bytes_invalid=0 send_seq=301453 receive_seq=301453 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400014955 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13060 bytes_read=42250 bytes_retransmit=0 bytes_invalid=0 send_seq=2148 receive_seq=2148 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999186 adj=49997243 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=77698 bytes_read=2682553 bytes_retransmit=9 bytes_invalid=0 send_seq=10909 receive_seq=10909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997723 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22152 bytes_read=242139 bytes_retransmit=9 bytes_invalid=0 send_seq=2891 receive_seq=2891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997546 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13273 bytes_read=516480 bytes_retransmit=9 bytes_invalid=0 send_seq=2158 receive_seq=2158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13813 bytes_read=41447 bytes_retransmit=9 bytes_invalid=0 send_seq=2149 receive_seq=2149 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999449 Octopus_Pro_H723_V1.1: temp=36.1 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56889 bytes_read=931945 bytes_retransmit=0 bytes_invalid=0 send_seq=5786 receive_seq=5786 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998681 coil_temp=18.0 refs=0 mcu_temp=20.99 supply_voltage=3.012 th0: temp=37.5 th1: temp=37.7 th2: temp=40.2 th3: temp=39.0 sysload=0.00 cputime=180.405 memavail=7401792 print_time=2059.888 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2038.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=17661250 bytes_read=2041986 bytes_retransmit=9 bytes_invalid=0 send_seq=301509 receive_seq=301509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400014952 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13066 bytes_read=42266 bytes_retransmit=0 bytes_invalid=0 send_seq=2149 receive_seq=2149 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999186 adj=49997271 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=77704 bytes_read=2682653 bytes_retransmit=9 bytes_invalid=0 send_seq=10910 receive_seq=10910 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997736 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22158 bytes_read=242239 bytes_retransmit=9 bytes_invalid=0 send_seq=2892 receive_seq=2892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997564 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13279 bytes_read=516698 bytes_retransmit=9 bytes_invalid=0 send_seq=2159 receive_seq=2159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13819 bytes_read=41463 bytes_retransmit=9 bytes_invalid=0 send_seq=2150 receive_seq=2150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999454 Octopus_Pro_H723_V1.1: temp=35.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56895 bytes_read=932301 bytes_retransmit=0 bytes_invalid=0 send_seq=5787 receive_seq=5787 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998688 coil_temp=18.0 refs=0 mcu_temp=20.98 supply_voltage=3.012 th0: temp=37.7 th1: temp=37.8 th2: temp=40.6 th3: temp=39.2 sysload=0.00 cputime=180.465 memavail=7401792 print_time=2060.888 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2039.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000006 bytes_write=17662438 bytes_read=2042751 bytes_retransmit=9 bytes_invalid=0 send_seq=301565 receive_seq=301565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400014954 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13072 bytes_read=42282 bytes_retransmit=0 bytes_invalid=0 send_seq=2150 receive_seq=2150 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999186 adj=49997285 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=77710 bytes_read=2682767 bytes_retransmit=9 bytes_invalid=0 send_seq=10911 receive_seq=10911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997795 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22164 bytes_read=242339 bytes_retransmit=9 bytes_invalid=0 send_seq=2893 receive_seq=2893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997582 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13285 bytes_read=516916 bytes_retransmit=9 bytes_invalid=0 send_seq=2160 receive_seq=2160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13825 bytes_read=41479 bytes_retransmit=9 bytes_invalid=0 send_seq=2151 receive_seq=2151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999457 Octopus_Pro_H723_V1.1: temp=35.6 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56901 bytes_read=932657 bytes_retransmit=0 bytes_invalid=0 send_seq=5788 receive_seq=5788 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998689 coil_temp=18.0 refs=0 mcu_temp=20.98 supply_voltage=3.012 th0: temp=38.0 th1: temp=38.0 th2: temp=40.4 th3: temp=39.4 sysload=0.00 cputime=180.524 memavail=7401792 print_time=2061.888 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2040.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17663642 bytes_read=2043551 bytes_retransmit=9 bytes_invalid=0 send_seq=301622 receive_seq=301622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400014949 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13078 bytes_read=42298 bytes_retransmit=0 bytes_invalid=0 send_seq=2151 receive_seq=2151 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999186 adj=49997285 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=77716 bytes_read=2682895 bytes_retransmit=9 bytes_invalid=0 send_seq=10912 receive_seq=10912 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997884 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22170 bytes_read=242467 bytes_retransmit=9 bytes_invalid=0 send_seq=2894 receive_seq=2894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997595 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13291 bytes_read=517225 bytes_retransmit=9 bytes_invalid=0 send_seq=2161 receive_seq=2161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13831 bytes_read=41495 bytes_retransmit=9 bytes_invalid=0 send_seq=2152 receive_seq=2152 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999460 Octopus_Pro_H723_V1.1: temp=35.5 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56907 bytes_read=933013 bytes_retransmit=0 bytes_invalid=0 send_seq=5789 receive_seq=5789 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998710 coil_temp=18.0 refs=0 mcu_temp=20.97 supply_voltage=3.012 th0: temp=38.1 th1: temp=38.2 th2: temp=40.7 th3: temp=39.6 sysload=0.00 cputime=180.584 memavail=7401792 print_time=2062.888 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2041.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17664836 bytes_read=2044352 bytes_retransmit=9 bytes_invalid=0 send_seq=301678 receive_seq=301678 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400014953 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=13084 bytes_read=42327 bytes_retransmit=0 bytes_invalid=0 send_seq=2152 receive_seq=2152 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999187 adj=49997308 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=77722 bytes_read=2682995 bytes_retransmit=9 bytes_invalid=0 send_seq=10913 receive_seq=10913 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997942 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22176 bytes_read=242581 bytes_retransmit=9 bytes_invalid=0 send_seq=2895 receive_seq=2895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997615 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13297 bytes_read=517459 bytes_retransmit=9 bytes_invalid=0 send_seq=2162 receive_seq=2162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997724 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13837 bytes_read=41511 bytes_retransmit=9 bytes_invalid=0 send_seq=2153 receive_seq=2153 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999462 Octopus_Pro_H723_V1.1: temp=35.4 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56913 bytes_read=933369 bytes_retransmit=0 bytes_invalid=0 send_seq=5790 receive_seq=5790 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998723 coil_temp=18.0 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=38.3 th1: temp=38.1 th2: temp=41.0 th3: temp=39.7 sysload=0.00 cputime=180.642 memavail=7401792 print_time=2063.888 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2042.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17666025 bytes_read=2045119 bytes_retransmit=9 bytes_invalid=0 send_seq=301733 receive_seq=301733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400014948 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=13090 bytes_read=42343 bytes_retransmit=0 bytes_invalid=0 send_seq=2153 receive_seq=2153 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999187 adj=49997313 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=77728 bytes_read=2683095 bytes_retransmit=9 bytes_invalid=0 send_seq=10914 receive_seq=10914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997906 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22182 bytes_read=242681 bytes_retransmit=9 bytes_invalid=0 send_seq=2896 receive_seq=2896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997609 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13303 bytes_read=517693 bytes_retransmit=9 bytes_invalid=0 send_seq=2163 receive_seq=2163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997705 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13843 bytes_read=41538 bytes_retransmit=9 bytes_invalid=0 send_seq=2154 receive_seq=2154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999460 Octopus_Pro_H723_V1.1: temp=35.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56919 bytes_read=933725 bytes_retransmit=0 bytes_invalid=0 send_seq=5791 receive_seq=5791 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998711 coil_temp=18.0 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=38.7 th1: temp=37.7 th2: temp=41.1 th3: temp=39.8 sysload=0.24 cputime=180.699 memavail=7401792 print_time=2064.888 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2043.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17667231 bytes_read=2045910 bytes_retransmit=9 bytes_invalid=0 send_seq=301790 receive_seq=301790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400014946 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=13096 bytes_read=42359 bytes_retransmit=0 bytes_invalid=0 send_seq=2154 receive_seq=2154 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999189 adj=49997322 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=77734 bytes_read=2683223 bytes_retransmit=9 bytes_invalid=0 send_seq=10915 receive_seq=10915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997877 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22188 bytes_read=242809 bytes_retransmit=9 bytes_invalid=0 send_seq=2897 receive_seq=2897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997625 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13309 bytes_read=517987 bytes_retransmit=9 bytes_invalid=0 send_seq=2164 receive_seq=2164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997722 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13849 bytes_read=41554 bytes_retransmit=9 bytes_invalid=0 send_seq=2155 receive_seq=2155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999463 Octopus_Pro_H723_V1.1: temp=35.1 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56925 bytes_read=934081 bytes_retransmit=0 bytes_invalid=0 send_seq=5792 receive_seq=5792 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998718 coil_temp=18.0 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=38.6 th1: temp=38.2 th2: temp=41.4 th3: temp=39.9 sysload=0.24 cputime=180.758 memavail=7401960 print_time=2065.888 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2044.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17668410 bytes_read=2046696 bytes_retransmit=9 bytes_invalid=0 send_seq=301843 receive_seq=301843 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400014949 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=13102 bytes_read=42375 bytes_retransmit=0 bytes_invalid=0 send_seq=2155 receive_seq=2155 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999190 adj=49997361 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=77740 bytes_read=2683337 bytes_retransmit=9 bytes_invalid=0 send_seq=10916 receive_seq=10916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997871 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22194 bytes_read=242909 bytes_retransmit=9 bytes_invalid=0 send_seq=2898 receive_seq=2898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997633 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13315 bytes_read=518221 bytes_retransmit=9 bytes_invalid=0 send_seq=2165 receive_seq=2165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997731 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13855 bytes_read=41570 bytes_retransmit=9 bytes_invalid=0 send_seq=2156 receive_seq=2156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999464 Octopus_Pro_H723_V1.1: temp=34.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56931 bytes_read=934437 bytes_retransmit=0 bytes_invalid=0 send_seq=5793 receive_seq=5793 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998717 coil_temp=18.0 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=38.8 th1: temp=38.7 th2: temp=41.7 th3: temp=40.1 sysload=0.24 cputime=180.815 memavail=7401960 print_time=2066.888 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2045.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17669579 bytes_read=2047458 bytes_retransmit=9 bytes_invalid=0 send_seq=301894 receive_seq=301894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015061 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=13108 bytes_read=42391 bytes_retransmit=0 bytes_invalid=0 send_seq=2156 receive_seq=2156 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999189 adj=49997359 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=77746 bytes_read=2683437 bytes_retransmit=9 bytes_invalid=0 send_seq=10917 receive_seq=10917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997836 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22200 bytes_read=243009 bytes_retransmit=9 bytes_invalid=0 send_seq=2899 receive_seq=2899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997745 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13321 bytes_read=518470 bytes_retransmit=9 bytes_invalid=0 send_seq=2166 receive_seq=2166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997719 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13861 bytes_read=41586 bytes_retransmit=9 bytes_invalid=0 send_seq=2157 receive_seq=2157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999463 Octopus_Pro_H723_V1.1: temp=34.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56937 bytes_read=934793 bytes_retransmit=0 bytes_invalid=0 send_seq=5794 receive_seq=5794 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998715 coil_temp=18.0 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=38.8 th1: temp=38.9 th2: temp=41.6 th3: temp=40.2 sysload=0.24 cputime=180.883 memavail=7397308 print_time=2067.888 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2046.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17670973 bytes_read=2048316 bytes_retransmit=9 bytes_invalid=0 send_seq=301956 receive_seq=301956 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015075 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13114 bytes_read=42420 bytes_retransmit=0 bytes_invalid=0 send_seq=2157 receive_seq=2157 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999189 adj=49997117 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=77752 bytes_read=2683565 bytes_retransmit=9 bytes_invalid=0 send_seq=10918 receive_seq=10918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997540 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22206 bytes_read=243151 bytes_retransmit=9 bytes_invalid=0 send_seq=2900 receive_seq=2900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997597 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13327 bytes_read=518764 bytes_retransmit=9 bytes_invalid=0 send_seq=2167 receive_seq=2167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997503 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13867 bytes_read=41602 bytes_retransmit=9 bytes_invalid=0 send_seq=2158 receive_seq=2158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999411 Octopus_Pro_H723_V1.1: temp=34.7 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56943 bytes_read=935149 bytes_retransmit=0 bytes_invalid=0 send_seq=5795 receive_seq=5795 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998588 coil_temp=18.0 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=38.9 th1: temp=38.8 th2: temp=41.7 th3: temp=40.4 sysload=0.24 cputime=180.948 memavail=7403708 print_time=2068.844 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2047.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17674543 bytes_read=2049312 bytes_retransmit=9 bytes_invalid=0 send_seq=302051 receive_seq=302051 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015085 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13120 bytes_read=42436 bytes_retransmit=0 bytes_invalid=0 send_seq=2158 receive_seq=2158 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999189 adj=49997132 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=77791 bytes_read=2683665 bytes_retransmit=9 bytes_invalid=0 send_seq=10919 receive_seq=10919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997565 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22212 bytes_read=243251 bytes_retransmit=9 bytes_invalid=0 send_seq=2901 receive_seq=2901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997559 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13333 bytes_read=518998 bytes_retransmit=9 bytes_invalid=0 send_seq=2168 receive_seq=2168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997567 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13873 bytes_read=41629 bytes_retransmit=9 bytes_invalid=0 send_seq=2159 receive_seq=2159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999421 Octopus_Pro_H723_V1.1: temp=34.5 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56949 bytes_read=935505 bytes_retransmit=0 bytes_invalid=0 send_seq=5796 receive_seq=5796 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998605 coil_temp=18.0 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=38.7 th1: temp=38.6 th2: temp=41.4 th3: temp=40.2 sysload=0.22 cputime=181.039 memavail=7403708 print_time=2069.875 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2048.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17676549 bytes_read=2052051 bytes_retransmit=9 bytes_invalid=0 send_seq=302212 receive_seq=302212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015070 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13126 bytes_read=42452 bytes_retransmit=0 bytes_invalid=0 send_seq=2159 receive_seq=2159 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999188 adj=49997155 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=79177 bytes_read=2685978 bytes_retransmit=9 bytes_invalid=0 send_seq=11035 receive_seq=11035 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997721 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22218 bytes_read=243351 bytes_retransmit=9 bytes_invalid=0 send_seq=2902 receive_seq=2902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997537 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13339 bytes_read=519232 bytes_retransmit=9 bytes_invalid=0 send_seq=2169 receive_seq=2169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997591 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13879 bytes_read=41645 bytes_retransmit=9 bytes_invalid=0 send_seq=2160 receive_seq=2160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999443 Octopus_Pro_H723_V1.1: temp=34.5 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56955 bytes_read=935861 bytes_retransmit=0 bytes_invalid=0 send_seq=5797 receive_seq=5797 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998609 coil_temp=18.0 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=39.1 th1: temp=39.0 th2: temp=42.0 th3: temp=40.7 sysload=0.22 cputime=181.136 memavail=7403708 print_time=2070.875 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2049.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17678710 bytes_read=2055103 bytes_retransmit=9 bytes_invalid=0 send_seq=302388 receive_seq=302388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015055 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13132 bytes_read=42468 bytes_retransmit=0 bytes_invalid=0 send_seq=2160 receive_seq=2160 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999188 adj=49997218 toolboard_t0: mcu_awake=0.017 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=80803 bytes_read=2688658 bytes_retransmit=9 bytes_invalid=0 send_seq=11171 receive_seq=11171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997800 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22224 bytes_read=243479 bytes_retransmit=9 bytes_invalid=0 send_seq=2903 receive_seq=2903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997607 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13345 bytes_read=519526 bytes_retransmit=9 bytes_invalid=0 send_seq=2170 receive_seq=2170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13885 bytes_read=41661 bytes_retransmit=9 bytes_invalid=0 send_seq=2161 receive_seq=2161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999454 Octopus_Pro_H723_V1.1: temp=34.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56961 bytes_read=936217 bytes_retransmit=0 bytes_invalid=0 send_seq=5798 receive_seq=5798 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998676 coil_temp=18.0 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=39.6 th1: temp=39.1 th2: temp=42.2 th3: temp=40.7 sysload=0.22 cputime=181.241 memavail=7403708 print_time=2071.875 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2050.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=17680797 bytes_read=2058139 bytes_retransmit=9 bytes_invalid=0 send_seq=302564 receive_seq=302564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015043 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13138 bytes_read=42484 bytes_retransmit=0 bytes_invalid=0 send_seq=2161 receive_seq=2161 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999189 adj=49997269 toolboard_t0: mcu_awake=0.017 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=82417 bytes_read=2691290 bytes_retransmit=9 bytes_invalid=0 send_seq=11306 receive_seq=11306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997808 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22230 bytes_read=243579 bytes_retransmit=9 bytes_invalid=0 send_seq=2904 receive_seq=2904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997629 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13351 bytes_read=519775 bytes_retransmit=9 bytes_invalid=0 send_seq=2171 receive_seq=2171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997695 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13891 bytes_read=41677 bytes_retransmit=9 bytes_invalid=0 send_seq=2162 receive_seq=2162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999462 Octopus_Pro_H723_V1.1: temp=34.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56967 bytes_read=936573 bytes_retransmit=0 bytes_invalid=0 send_seq=5799 receive_seq=5799 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998691 coil_temp=18.0 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=39.6 th1: temp=38.8 th2: temp=42.6 th3: temp=40.7 sysload=0.22 cputime=181.344 memavail=7403708 print_time=2072.875 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2051.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=17682953 bytes_read=2061176 bytes_retransmit=9 bytes_invalid=0 send_seq=302741 receive_seq=302741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015115 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13144 bytes_read=42513 bytes_retransmit=0 bytes_invalid=0 send_seq=2162 receive_seq=2162 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999189 adj=49997315 toolboard_t0: mcu_awake=0.017 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=84031 bytes_read=2693936 bytes_retransmit=9 bytes_invalid=0 send_seq=11441 receive_seq=11441 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997809 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22236 bytes_read=243693 bytes_retransmit=9 bytes_invalid=0 send_seq=2905 receive_seq=2905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997644 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13357 bytes_read=520009 bytes_retransmit=9 bytes_invalid=0 send_seq=2172 receive_seq=2172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997714 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13897 bytes_read=41693 bytes_retransmit=9 bytes_invalid=0 send_seq=2163 receive_seq=2163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999466 Octopus_Pro_H723_V1.1: temp=34.1 EBB42_Gen2_v1.0_T0: temp=31.1 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56973 bytes_read=936929 bytes_retransmit=0 bytes_invalid=0 send_seq=5800 receive_seq=5800 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998702 coil_temp=18.0 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=39.5 th1: temp=39.0 th2: temp=42.6 th3: temp=41.1 sysload=0.22 cputime=181.447 memavail=7403708 print_time=2073.875 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2052.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=17685119 bytes_read=2064247 bytes_retransmit=9 bytes_invalid=0 send_seq=302918 receive_seq=302918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015100 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13150 bytes_read=42529 bytes_retransmit=0 bytes_invalid=0 send_seq=2163 receive_seq=2163 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999188 adj=49997163 toolboard_t0: mcu_awake=0.017 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=85657 bytes_read=2696601 bytes_retransmit=9 bytes_invalid=0 send_seq=11577 receive_seq=11577 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997605 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22242 bytes_read=243821 bytes_retransmit=9 bytes_invalid=0 send_seq=2906 receive_seq=2906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997447 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13363 bytes_read=520303 bytes_retransmit=9 bytes_invalid=0 send_seq=2173 receive_seq=2173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997570 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13903 bytes_read=41720 bytes_retransmit=9 bytes_invalid=0 send_seq=2164 receive_seq=2164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999431 Octopus_Pro_H723_V1.1: temp=34.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56979 bytes_read=937285 bytes_retransmit=0 bytes_invalid=0 send_seq=5801 receive_seq=5801 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998603 coil_temp=18.0 refs=0 mcu_temp=20.97 supply_voltage=3.012 th0: temp=39.3 th1: temp=39.4 th2: temp=42.7 th3: temp=41.3 sysload=0.20 cputime=181.555 memavail=7403708 print_time=2074.875 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2053.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=17687297 bytes_read=2067338 bytes_retransmit=9 bytes_invalid=0 send_seq=303096 receive_seq=303096 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015085 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13156 bytes_read=42545 bytes_retransmit=0 bytes_invalid=0 send_seq=2164 receive_seq=2164 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999188 adj=49997213 toolboard_t0: mcu_awake=0.017 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=87259 bytes_read=2699242 bytes_retransmit=9 bytes_invalid=0 send_seq=11711 receive_seq=11711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997660 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22248 bytes_read=243921 bytes_retransmit=9 bytes_invalid=0 send_seq=2907 receive_seq=2907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997576 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13369 bytes_read=520537 bytes_retransmit=9 bytes_invalid=0 send_seq=2174 receive_seq=2174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13909 bytes_read=41736 bytes_retransmit=9 bytes_invalid=0 send_seq=2165 receive_seq=2165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999448 Octopus_Pro_H723_V1.1: temp=33.9 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56985 bytes_read=937641 bytes_retransmit=0 bytes_invalid=0 send_seq=5802 receive_seq=5802 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998655 coil_temp=18.0 refs=0 mcu_temp=20.97 supply_voltage=3.012 th0: temp=39.8 th1: temp=39.4 th2: temp=43.1 th3: temp=41.3 sysload=0.20 cputime=181.655 memavail=7403708 print_time=2075.875 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2054.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=17689390 bytes_read=2070225 bytes_retransmit=9 bytes_invalid=0 send_seq=303264 receive_seq=303264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=0 freq=400015075 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13162 bytes_read=42561 bytes_retransmit=0 bytes_invalid=0 send_seq=2165 receive_seq=2165 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999187 adj=49997264 toolboard_t0: mcu_awake=0.072 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=88766 bytes_read=2701716 bytes_retransmit=9 bytes_invalid=0 send_seq=11838 receive_seq=11838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=0 freq=64000209 adj=63997724 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22254 bytes_read=244021 bytes_retransmit=9 bytes_invalid=0 send_seq=2908 receive_seq=2908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997615 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13375 bytes_read=520771 bytes_retransmit=9 bytes_invalid=0 send_seq=2175 receive_seq=2175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13915 bytes_read=41752 bytes_retransmit=9 bytes_invalid=0 send_seq=2166 receive_seq=2166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999456 Octopus_Pro_H723_V1.1: temp=33.8 EBB42_Gen2_v1.0_T0: temp=31.2 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56991 bytes_read=937997 bytes_retransmit=0 bytes_invalid=0 send_seq=5803 receive_seq=5803 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998690 coil_temp=18.0 refs=0 mcu_temp=20.98 supply_voltage=3.012 th0: temp=40.0 th1: temp=39.4 th2: temp=43.0 th3: temp=41.6 sysload=0.20 cputime=181.754 memavail=7403708 print_time=2077.021 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 2055.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000002 mcu_task_stddev=0.000002 bytes_write=17690749 bytes_read=2071840 bytes_retransmit=9 bytes_invalid=0 send_seq=303362 receive_seq=303362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015152 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13168 bytes_read=42577 bytes_retransmit=0 bytes_invalid=0 send_seq=2166 receive_seq=2166 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999187 adj=49997290 toolboard_t0: mcu_awake=0.072 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=89195 bytes_read=2702482 bytes_retransmit=9 bytes_invalid=0 send_seq=11873 receive_seq=11873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997742 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=22586 bytes_read=244638 bytes_retransmit=9 bytes_invalid=0 send_seq=2934 receive_seq=2934 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997627 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13381 bytes_read=521080 bytes_retransmit=9 bytes_invalid=0 send_seq=2176 receive_seq=2176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997692 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13921 bytes_read=41768 bytes_retransmit=9 bytes_invalid=0 send_seq=2167 receive_seq=2167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999468 Octopus_Pro_H723_V1.1: temp=33.7 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=56997 bytes_read=938353 bytes_retransmit=0 bytes_invalid=0 send_seq=5804 receive_seq=5804 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998706 coil_temp=18.0 refs=0 mcu_temp=20.98 supply_voltage=3.012 th0: temp=39.3 th1: temp=39.6 th2: temp=43.2 th3: temp=41.7 sysload=0.20 cputime=181.832 memavail=7403460 print_time=2077.862 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2056.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000002 mcu_task_stddev=0.000002 bytes_write=17692927 bytes_read=2074931 bytes_retransmit=9 bytes_invalid=0 send_seq=303540 receive_seq=303540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015137 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13174 bytes_read=42606 bytes_retransmit=0 bytes_invalid=0 send_seq=2167 receive_seq=2167 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999198 adj=49997140 toolboard_t0: mcu_awake=0.072 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=89201 bytes_read=2702582 bytes_retransmit=9 bytes_invalid=0 send_seq=11874 receive_seq=11874 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997539 toolboard_t1: mcu_awake=0.014 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=24200 bytes_read=247285 bytes_retransmit=9 bytes_invalid=0 send_seq=3069 receive_seq=3069 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997420 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13387 bytes_read=521314 bytes_retransmit=9 bytes_invalid=0 send_seq=2177 receive_seq=2177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997545 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13927 bytes_read=41784 bytes_retransmit=9 bytes_invalid=0 send_seq=2168 receive_seq=2168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999429 Octopus_Pro_H723_V1.1: temp=33.6 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=57003 bytes_read=938709 bytes_retransmit=0 bytes_invalid=0 send_seq=5805 receive_seq=5805 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998629 coil_temp=18.0 refs=0 mcu_temp=20.97 supply_voltage=3.012 th0: temp=39.7 th1: temp=39.4 th2: temp=43.7 th3: temp=41.8 sysload=0.20 cputime=181.934 memavail=7402476 print_time=2078.862 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2057.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000002 mcu_task_stddev=0.000002 bytes_write=17695078 bytes_read=2077987 bytes_retransmit=9 bytes_invalid=0 send_seq=303714 receive_seq=303714 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015202 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13180 bytes_read=42622 bytes_retransmit=0 bytes_invalid=0 send_seq=2168 receive_seq=2168 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999197 adj=49997382 toolboard_t0: mcu_awake=0.072 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=89207 bytes_read=2702675 bytes_retransmit=9 bytes_invalid=0 send_seq=11875 receive_seq=11875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997638 toolboard_t1: mcu_awake=0.014 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=25732 bytes_read=249826 bytes_retransmit=9 bytes_invalid=0 send_seq=3205 receive_seq=3205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997488 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13393 bytes_read=521548 bytes_retransmit=9 bytes_invalid=0 send_seq=2178 receive_seq=2178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997613 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13933 bytes_read=41811 bytes_retransmit=9 bytes_invalid=0 send_seq=2169 receive_seq=2169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999441 Octopus_Pro_H723_V1.1: temp=33.4 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=57009 bytes_read=939065 bytes_retransmit=0 bytes_invalid=0 send_seq=5806 receive_seq=5806 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998672 coil_temp=18.0 refs=0 mcu_temp=20.97 supply_voltage=3.012 th0: temp=39.9 th1: temp=39.3 th2: temp=43.5 th3: temp=41.9 sysload=0.19 cputime=182.036 memavail=7402476 print_time=2079.862 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2058.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000002 mcu_task_stddev=0.000002 bytes_write=17697256 bytes_read=2081049 bytes_retransmit=9 bytes_invalid=0 send_seq=303892 receive_seq=303892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015267 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13186 bytes_read=42638 bytes_retransmit=0 bytes_invalid=0 send_seq=2169 receive_seq=2169 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999196 adj=49997211 toolboard_t0: mcu_awake=0.072 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=89213 bytes_read=2702793 bytes_retransmit=9 bytes_invalid=0 send_seq=11876 receive_seq=11876 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997507 toolboard_t1: mcu_awake=0.014 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=27197 bytes_read=252347 bytes_retransmit=9 bytes_invalid=0 send_seq=3339 receive_seq=3339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997338 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13399 bytes_read=521842 bytes_retransmit=9 bytes_invalid=0 send_seq=2179 receive_seq=2179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997530 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13939 bytes_read=41827 bytes_retransmit=9 bytes_invalid=0 send_seq=2170 receive_seq=2170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999415 Octopus_Pro_H723_V1.1: temp=33.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=57015 bytes_read=939421 bytes_retransmit=0 bytes_invalid=0 send_seq=5807 receive_seq=5807 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998590 coil_temp=18.0 refs=0 mcu_temp=20.97 supply_voltage=3.012 th0: temp=39.9 th1: temp=39.2 th2: temp=43.6 th3: temp=42.3 sysload=0.19 cputime=182.141 memavail=7402476 print_time=2080.862 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2059.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000002 mcu_task_stddev=0.000002 bytes_write=17699400 bytes_read=2084120 bytes_retransmit=9 bytes_invalid=0 send_seq=304066 receive_seq=304066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015265 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13192 bytes_read=42654 bytes_retransmit=0 bytes_invalid=0 send_seq=2170 receive_seq=2170 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999196 adj=49997087 toolboard_t0: mcu_awake=0.016 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=89219 bytes_read=2702901 bytes_retransmit=9 bytes_invalid=0 send_seq=11877 receive_seq=11877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997429 toolboard_t1: mcu_awake=0.014 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=28677 bytes_read=254834 bytes_retransmit=9 bytes_invalid=0 send_seq=3474 receive_seq=3473 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997229 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13405 bytes_read=522076 bytes_retransmit=9 bytes_invalid=0 send_seq=2180 receive_seq=2180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999522 adj=47997459 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13945 bytes_read=41843 bytes_retransmit=9 bytes_invalid=0 send_seq=2171 receive_seq=2171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999397 Octopus_Pro_H723_V1.1: temp=33.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=57021 bytes_read=939777 bytes_retransmit=0 bytes_invalid=0 send_seq=5808 receive_seq=5808 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998526 coil_temp=18.0 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=39.9 th1: temp=39.3 th2: temp=44.3 th3: temp=42.4 sysload=0.19 cputime=182.245 memavail=7402476 print_time=2081.862 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2060.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000002 mcu_task_stddev=0.000003 bytes_write=17701561 bytes_read=2087202 bytes_retransmit=9 bytes_invalid=0 send_seq=304242 receive_seq=304242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015323 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13198 bytes_read=42670 bytes_retransmit=0 bytes_invalid=0 send_seq=2171 receive_seq=2171 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999195 adj=49997148 toolboard_t0: mcu_awake=0.016 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=89225 bytes_read=2702994 bytes_retransmit=9 bytes_invalid=0 send_seq=11878 receive_seq=11878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997502 toolboard_t1: mcu_awake=0.014 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=30157 bytes_read=257331 bytes_retransmit=9 bytes_invalid=0 send_seq=3609 receive_seq=3609 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997311 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13411 bytes_read=522325 bytes_retransmit=9 bytes_invalid=0 send_seq=2181 receive_seq=2181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997567 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13951 bytes_read=41859 bytes_retransmit=9 bytes_invalid=0 send_seq=2172 receive_seq=2172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=33.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=57027 bytes_read=940133 bytes_retransmit=0 bytes_invalid=0 send_seq=5809 receive_seq=5809 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998639 coil_temp=18.0 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=39.9 th1: temp=39.2 th2: temp=44.1 th3: temp=42.6 sysload=0.19 cputime=182.354 memavail=7402512 print_time=2082.862 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2061.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000002 mcu_task_stddev=0.000003 bytes_write=17703231 bytes_read=2089355 bytes_retransmit=9 bytes_invalid=0 send_seq=304374 receive_seq=304374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015294 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13204 bytes_read=42699 bytes_retransmit=0 bytes_invalid=0 send_seq=2172 receive_seq=2172 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999195 adj=49997058 toolboard_t0: mcu_awake=0.016 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=89231 bytes_read=2703119 bytes_retransmit=9 bytes_invalid=0 send_seq=11879 receive_seq=11879 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997403 toolboard_t1: mcu_awake=0.071 mcu_task_avg=0.000017 mcu_task_stddev=0.000010 bytes_write=31215 bytes_read=259114 bytes_retransmit=9 bytes_invalid=0 send_seq=3702 receive_seq=3702 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997570 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13417 bytes_read=522619 bytes_retransmit=9 bytes_invalid=0 send_seq=2182 receive_seq=2182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997483 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13957 bytes_read=41875 bytes_retransmit=9 bytes_invalid=0 send_seq=2173 receive_seq=2173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999414 Octopus_Pro_H723_V1.1: temp=33.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=57033 bytes_read=940489 bytes_retransmit=0 bytes_invalid=0 send_seq=5810 receive_seq=5810 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998576 coil_temp=18.0 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=40.1 th1: temp=39.1 th2: temp=44.1 th3: temp=42.6 sysload=0.19 cputime=182.443 memavail=7402512 print_time=2083.861 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2062.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000002 mcu_task_stddev=0.000003 bytes_write=17704793 bytes_read=2090507 bytes_retransmit=9 bytes_invalid=0 send_seq=304444 receive_seq=304444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015266 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13210 bytes_read=42715 bytes_retransmit=0 bytes_invalid=0 send_seq=2173 receive_seq=2173 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999195 adj=49997160 toolboard_t0: mcu_awake=0.016 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=89237 bytes_read=2703219 bytes_retransmit=9 bytes_invalid=0 send_seq=11880 receive_seq=11880 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997546 toolboard_t1: mcu_awake=0.071 mcu_task_avg=0.000017 mcu_task_stddev=0.000010 bytes_write=31606 bytes_read=259847 bytes_retransmit=9 bytes_invalid=0 send_seq=3736 receive_seq=3736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997614 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13423 bytes_read=522853 bytes_retransmit=9 bytes_invalid=0 send_seq=2183 receive_seq=2183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997582 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13963 bytes_read=41902 bytes_retransmit=9 bytes_invalid=0 send_seq=2174 receive_seq=2174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=33.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=57039 bytes_read=940845 bytes_retransmit=0 bytes_invalid=0 send_seq=5811 receive_seq=5811 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998638 coil_temp=18.0 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=39.9 th1: temp=38.7 th2: temp=44.2 th3: temp=42.9 sysload=0.25 cputime=182.522 memavail=7399016 print_time=2084.878 buffer_time=0.197 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
RatOS:: Homing Z
Stats 2063.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000002 mcu_task_stddev=0.000003 bytes_write=17706541 bytes_read=2092324 bytes_retransmit=9 bytes_invalid=0 send_seq=304555 receive_seq=304555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015246 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13216 bytes_read=42731 bytes_retransmit=0 bytes_invalid=0 send_seq=2174 receive_seq=2174 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999194 adj=49997248 toolboard_t0: mcu_awake=0.016 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=89243 bytes_read=2703319 bytes_retransmit=9 bytes_invalid=0 send_seq=11881 receive_seq=11881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997669 toolboard_t1: mcu_awake=0.071 mcu_task_avg=0.000017 mcu_task_stddev=0.000010 bytes_write=31612 bytes_read=259947 bytes_retransmit=9 bytes_invalid=0 send_seq=3737 receive_seq=3737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997788 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13429 bytes_read=523087 bytes_retransmit=9 bytes_invalid=0 send_seq=2184 receive_seq=2184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997730 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13969 bytes_read=41918 bytes_retransmit=9 bytes_invalid=0 send_seq=2175 receive_seq=2175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999455 Octopus_Pro_H723_V1.1: temp=32.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=57916 bytes_read=942588 bytes_retransmit=0 bytes_invalid=0 send_seq=5884 receive_seq=5883 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998686 coil_temp=18.0 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=40.8 th1: temp=39.4 th2: temp=44.4 th3: temp=42.6 sysload=0.25 cputime=182.617 memavail=7403652 print_time=2085.889 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 2064.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000002 mcu_task_stddev=0.000003 bytes_write=17709010 bytes_read=2095385 bytes_retransmit=9 bytes_invalid=0 send_seq=304730 receive_seq=304730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015231 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13222 bytes_read=42747 bytes_retransmit=0 bytes_invalid=0 send_seq=2175 receive_seq=2175 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999193 adj=49997291 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=89249 bytes_read=2703461 bytes_retransmit=9 bytes_invalid=0 send_seq=11882 receive_seq=11882 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997722 toolboard_t1: mcu_awake=0.071 mcu_task_avg=0.000017 mcu_task_stddev=0.000010 bytes_write=31618 bytes_read=260075 bytes_retransmit=9 bytes_invalid=0 send_seq=3738 receive_seq=3738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997790 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13435 bytes_read=523381 bytes_retransmit=9 bytes_invalid=0 send_seq=2185 receive_seq=2185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997749 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13975 bytes_read=41934 bytes_retransmit=9 bytes_invalid=0 send_seq=2176 receive_seq=2176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999464 Octopus_Pro_H723_V1.1: temp=33.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=59518 bytes_read=945476 bytes_retransmit=0 bytes_invalid=0 send_seq=6018 receive_seq=6018 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998710 coil_temp=18.0 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=40.6 th1: temp=39.4 th2: temp=44.5 th3: temp=42.9 sysload=0.25 cputime=182.721 memavail=7403652 print_time=2086.889 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2065.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=17711508 bytes_read=2098492 bytes_retransmit=9 bytes_invalid=0 send_seq=304908 receive_seq=304908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015211 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13228 bytes_read=42763 bytes_retransmit=0 bytes_invalid=0 send_seq=2176 receive_seq=2176 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999192 adj=49997308 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=89255 bytes_read=2703561 bytes_retransmit=9 bytes_invalid=0 send_seq=11883 receive_seq=11883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997756 toolboard_t1: mcu_awake=0.071 mcu_task_avg=0.000017 mcu_task_stddev=0.000010 bytes_write=31624 bytes_read=260175 bytes_retransmit=9 bytes_invalid=0 send_seq=3739 receive_seq=3739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997796 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13441 bytes_read=523630 bytes_retransmit=9 bytes_invalid=0 send_seq=2186 receive_seq=2186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997765 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13981 bytes_read=41950 bytes_retransmit=9 bytes_invalid=0 send_seq=2177 receive_seq=2177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999468 Octopus_Pro_H723_V1.1: temp=32.7 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=61120 bytes_read=948373 bytes_retransmit=0 bytes_invalid=0 send_seq=6152 receive_seq=6152 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998721 coil_temp=18.0 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=40.3 th1: temp=39.0 th2: temp=44.9 th3: temp=43.3 sysload=0.25 cputime=182.823 memavail=7403652 print_time=2087.889 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2066.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=17714205 bytes_read=2101420 bytes_retransmit=9 bytes_invalid=0 send_seq=305082 receive_seq=305082 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015189 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13234 bytes_read=42792 bytes_retransmit=0 bytes_invalid=0 send_seq=2177 receive_seq=2177 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999192 adj=49997321 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=89261 bytes_read=2703661 bytes_retransmit=9 bytes_invalid=0 send_seq=11884 receive_seq=11884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997792 toolboard_t1: mcu_awake=0.007 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=31630 bytes_read=260290 bytes_retransmit=9 bytes_invalid=0 send_seq=3740 receive_seq=3740 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997761 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13447 bytes_read=523864 bytes_retransmit=9 bytes_invalid=0 send_seq=2187 receive_seq=2187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997858 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13987 bytes_read=41966 bytes_retransmit=9 bytes_invalid=0 send_seq=2178 receive_seq=2178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999478 Octopus_Pro_H723_V1.1: temp=32.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62552 bytes_read=951268 bytes_retransmit=0 bytes_invalid=0 send_seq=6274 receive_seq=6274 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998733 coil_temp=18.0 refs=1 mcu_temp=20.92 supply_voltage=3.012 th0: temp=40.5 th1: temp=39.1 th2: temp=44.8 th3: temp=43.2 sysload=0.25 cputime=182.957 memavail=7403192 print_time=2089.547 buffer_time=0.865 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Extruder extruder already active
Extruder 'extruder' now syncing with 'extruder'
Extruder 'extruder1' now syncing with 'extruder'
RatOS | SET_PRESSURE_ADVANCE:: T0
extruder: pressure_advance: 0.008000
pressure_advance_smooth_time: 0.040000
RatOS | SET_PRESSURE_ADVANCE:: T1
extruder1: pressure_advance: 0.008000
pressure_advance_smooth_time: 0.040000
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 2067.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=17718365 bytes_read=2102160 bytes_retransmit=9 bytes_invalid=0 send_seq=305168 receive_seq=305168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=0 freq=400015179 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13240 bytes_read=42808 bytes_retransmit=0 bytes_invalid=0 send_seq=2178 receive_seq=2178 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999194 adj=49997351 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=89267 bytes_read=2703789 bytes_retransmit=9 bytes_invalid=0 send_seq=11885 receive_seq=11885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997826 toolboard_t1: mcu_awake=0.007 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=31636 bytes_read=260418 bytes_retransmit=9 bytes_invalid=0 send_seq=3741 receive_seq=3741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997729 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13453 bytes_read=524158 bytes_retransmit=9 bytes_invalid=0 send_seq=2188 receive_seq=2188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997830 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13993 bytes_read=41993 bytes_retransmit=9 bytes_invalid=0 send_seq=2179 receive_seq=2179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999478 Octopus_Pro_H723_V1.1: temp=32.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62565 bytes_read=954086 bytes_retransmit=0 bytes_invalid=0 send_seq=6276 receive_seq=6276 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998742 coil_temp=18.0 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=40.8 th1: temp=39.2 th2: temp=44.8 th3: temp=43.3 sysload=0.23 cputime=183.215 memavail=7403192 print_time=2091.960 buffer_time=2.277 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2068.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=17718677 bytes_read=2102614 bytes_retransmit=9 bytes_invalid=0 send_seq=305191 receive_seq=305191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015175 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13246 bytes_read=42824 bytes_retransmit=0 bytes_invalid=0 send_seq=2179 receive_seq=2179 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999194 adj=49997344 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=89273 bytes_read=2703889 bytes_retransmit=9 bytes_invalid=0 send_seq=11886 receive_seq=11886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997796 toolboard_t1: mcu_awake=0.007 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=31642 bytes_read=260518 bytes_retransmit=9 bytes_invalid=0 send_seq=3742 receive_seq=3742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997657 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13459 bytes_read=524392 bytes_retransmit=9 bytes_invalid=0 send_seq=2189 receive_seq=2189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997743 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=13999 bytes_read=42009 bytes_retransmit=9 bytes_invalid=0 send_seq=2180 receive_seq=2180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999469 Octopus_Pro_H723_V1.1: temp=32.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62571 bytes_read=954442 bytes_retransmit=0 bytes_invalid=0 send_seq=6277 receive_seq=6277 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998743 coil_temp=18.0 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=40.3 th1: temp=38.7 th2: temp=44.8 th3: temp=43.4 sysload=0.23 cputime=183.259 memavail=7403192 print_time=2091.960 buffer_time=1.276 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 2069.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=17718975 bytes_read=2103039 bytes_retransmit=9 bytes_invalid=0 send_seq=305214 receive_seq=305214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015164 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13252 bytes_read=42840 bytes_retransmit=0 bytes_invalid=0 send_seq=2180 receive_seq=2180 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999193 adj=49997349 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89279 bytes_read=2704003 bytes_retransmit=9 bytes_invalid=0 send_seq=11887 receive_seq=11887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997801 toolboard_t1: mcu_awake=0.007 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=31648 bytes_read=260618 bytes_retransmit=9 bytes_invalid=0 send_seq=3743 receive_seq=3743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997640 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13465 bytes_read=524626 bytes_retransmit=9 bytes_invalid=0 send_seq=2190 receive_seq=2190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997756 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14005 bytes_read=42025 bytes_retransmit=9 bytes_invalid=0 send_seq=2181 receive_seq=2181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999469 Octopus_Pro_H723_V1.1: temp=32.5 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62577 bytes_read=954798 bytes_retransmit=0 bytes_invalid=0 send_seq=6278 receive_seq=6278 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998738 coil_temp=18.0 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=40.0 th1: temp=38.9 th2: temp=45.1 th3: temp=43.2 sysload=0.23 cputime=183.301 memavail=7403192 print_time=2091.960 buffer_time=0.276 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2070.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=17719273 bytes_read=2103480 bytes_retransmit=9 bytes_invalid=0 send_seq=305237 receive_seq=305237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015188 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13258 bytes_read=42855 bytes_retransmit=0 bytes_invalid=0 send_seq=2181 receive_seq=2181 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999193 adj=49997361 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89285 bytes_read=2704131 bytes_retransmit=9 bytes_invalid=0 send_seq=11888 receive_seq=11888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997816 toolboard_t1: mcu_awake=0.007 mcu_task_avg=0.000016 mcu_task_stddev=0.000011 bytes_write=31654 bytes_read=260746 bytes_retransmit=9 bytes_invalid=0 send_seq=3744 receive_seq=3744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997644 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13471 bytes_read=524935 bytes_retransmit=9 bytes_invalid=0 send_seq=2191 receive_seq=2191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997764 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14011 bytes_read=42041 bytes_retransmit=9 bytes_invalid=0 send_seq=2182 receive_seq=2182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999472 Octopus_Pro_H723_V1.1: temp=32.7 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62583 bytes_read=955154 bytes_retransmit=0 bytes_invalid=0 send_seq=6279 receive_seq=6279 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998739 coil_temp=18.0 refs=0 mcu_temp=20.91 supply_voltage=3.012 th0: temp=40.4 th1: temp=39.3 th2: temp=45.0 th3: temp=43.4 sysload=0.23 cputime=183.347 memavail=7403192 print_time=2091.960 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2071.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=17719571 bytes_read=2103930 bytes_retransmit=9 bytes_invalid=0 send_seq=305260 receive_seq=305260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015179 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13264 bytes_read=42870 bytes_retransmit=0 bytes_invalid=0 send_seq=2182 receive_seq=2182 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999191 adj=49997314 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89291 bytes_read=2704231 bytes_retransmit=9 bytes_invalid=0 send_seq=11889 receive_seq=11889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997788 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=31660 bytes_read=260860 bytes_retransmit=9 bytes_invalid=0 send_seq=3745 receive_seq=3745 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997582 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13477 bytes_read=525169 bytes_retransmit=9 bytes_invalid=0 send_seq=2192 receive_seq=2192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997734 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14017 bytes_read=42057 bytes_retransmit=9 bytes_invalid=0 send_seq=2183 receive_seq=2183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999483 Octopus_Pro_H723_V1.1: temp=32.5 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62589 bytes_read=955510 bytes_retransmit=0 bytes_invalid=0 send_seq=6280 receive_seq=6280 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998741 coil_temp=18.0 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=40.4 th1: temp=39.4 th2: temp=45.3 th3: temp=43.6 sysload=0.23 cputime=183.388 memavail=7403192 print_time=2091.960 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
RatOS:: All requested axes already homed. Skipping homing.
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 2072.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=17720989 bytes_read=2104442 bytes_retransmit=9 bytes_invalid=0 send_seq=305301 receive_seq=305301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015169 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13270 bytes_read=42898 bytes_retransmit=0 bytes_invalid=0 send_seq=2183 receive_seq=2183 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999191 adj=49997312 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89297 bytes_read=2704331 bytes_retransmit=9 bytes_invalid=0 send_seq=11890 receive_seq=11890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997797 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=31666 bytes_read=260960 bytes_retransmit=9 bytes_invalid=0 send_seq=3746 receive_seq=3746 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13483 bytes_read=525403 bytes_retransmit=9 bytes_invalid=0 send_seq=2193 receive_seq=2193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997742 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14023 bytes_read=42084 bytes_retransmit=9 bytes_invalid=0 send_seq=2184 receive_seq=2184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999484 Octopus_Pro_H723_V1.1: temp=32.4 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62595 bytes_read=955866 bytes_retransmit=0 bytes_invalid=0 send_seq=6281 receive_seq=6281 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998804 coil_temp=18.0 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=40.3 th1: temp=39.6 th2: temp=45.3 th3: temp=43.7 sysload=0.21 cputime=183.470 memavail=7403192 print_time=2095.435 buffer_time=0.749 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Extruder extruder already active
Extruder 'extruder' now syncing with 'extruder'
Extruder 'extruder1' now syncing with 'extruder1'
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
RatOS | IDEX:: Selecting T1..
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 20.000000
RatOS | IDEX:: Toolhead offset applied for T1: X=-0.0 Y=-0.0 Z=-0.0
Activating extruder extruder1
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
Probing point (250.000, 250.000, 20.000)
Stats 2073.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=17724738 bytes_read=2105152 bytes_retransmit=9 bytes_invalid=0 send_seq=305381 receive_seq=305381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015170 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13276 bytes_read=42913 bytes_retransmit=0 bytes_invalid=0 send_seq=2184 receive_seq=2184 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999191 adj=49997323 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89303 bytes_read=2704459 bytes_retransmit=9 bytes_invalid=0 send_seq=11891 receive_seq=11891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997827 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=31672 bytes_read=261088 bytes_retransmit=9 bytes_invalid=0 send_seq=3747 receive_seq=3747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997595 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13489 bytes_read=525697 bytes_retransmit=9 bytes_invalid=0 send_seq=2194 receive_seq=2194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997736 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14029 bytes_read=42100 bytes_retransmit=9 bytes_invalid=0 send_seq=2185 receive_seq=2185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999478 Octopus_Pro_H723_V1.1: temp=32.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62601 bytes_read=956222 bytes_retransmit=0 bytes_invalid=0 send_seq=6282 receive_seq=6282 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998759 coil_temp=18.0 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=40.5 th1: temp=39.7 th2: temp=45.3 th3: temp=43.6 sysload=0.21 cputime=183.596 memavail=7403236 print_time=2096.914 buffer_time=1.228 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 2074.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=17725375 bytes_read=2105636 bytes_retransmit=9 bytes_invalid=0 send_seq=305410 receive_seq=305410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015162 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13282 bytes_read=42928 bytes_retransmit=0 bytes_invalid=0 send_seq=2185 receive_seq=2185 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999191 adj=49997306 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89309 bytes_read=2704573 bytes_retransmit=9 bytes_invalid=0 send_seq=11892 receive_seq=11892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997793 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=31678 bytes_read=261188 bytes_retransmit=9 bytes_invalid=0 send_seq=3748 receive_seq=3748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997573 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13495 bytes_read=525931 bytes_retransmit=9 bytes_invalid=0 send_seq=2195 receive_seq=2195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997706 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14035 bytes_read=42116 bytes_retransmit=9 bytes_invalid=0 send_seq=2186 receive_seq=2186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999467 Octopus_Pro_H723_V1.1: temp=32.4 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62607 bytes_read=956578 bytes_retransmit=0 bytes_invalid=0 send_seq=6283 receive_seq=6283 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998731 coil_temp=17.9 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=40.1 th1: temp=39.8 th2: temp=45.8 th3: temp=43.7 sysload=0.21 cputime=183.640 memavail=7403236 print_time=2096.914 buffer_time=0.227 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t1' measurements
toolhead: max_velocity: 600.000000
max_accel: 8379.841000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance testing
Testing frequency 10 Hz
Testing frequency 11 Hz
Testing frequency 12 Hz
Stats 2075.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17727999 bytes_read=2106266 bytes_retransmit=9 bytes_invalid=0 send_seq=305471 receive_seq=305471 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015161 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13288 bytes_read=42943 bytes_retransmit=0 bytes_invalid=0 send_seq=2186 receive_seq=2186 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999192 adj=49997321 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89315 bytes_read=2704673 bytes_retransmit=9 bytes_invalid=0 send_seq=11893 receive_seq=11893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997807 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=31833 bytes_read=263424 bytes_retransmit=9 bytes_invalid=0 send_seq=3766 receive_seq=3766 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997569 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13501 bytes_read=526180 bytes_retransmit=9 bytes_invalid=0 send_seq=2196 receive_seq=2196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997709 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14041 bytes_read=42132 bytes_retransmit=9 bytes_invalid=0 send_seq=2187 receive_seq=2187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999468 Octopus_Pro_H723_V1.1: temp=32.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62613 bytes_read=956918 bytes_retransmit=0 bytes_invalid=0 send_seq=6284 receive_seq=6284 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998746 coil_temp=17.9 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=40.6 th1: temp=40.1 th2: temp=45.6 th3: temp=43.8 sysload=0.21 cputime=183.803 memavail=7400212 print_time=2100.106 buffer_time=2.419 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2076.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17728946 bytes_read=2106741 bytes_retransmit=9 bytes_invalid=0 send_seq=305504 receive_seq=305504 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015154 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13294 bytes_read=42959 bytes_retransmit=0 bytes_invalid=0 send_seq=2187 receive_seq=2187 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999191 adj=49997313 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89321 bytes_read=2704801 bytes_retransmit=9 bytes_invalid=0 send_seq=11894 receive_seq=11894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997776 toolboard_t1: mcu_awake=0.097 mcu_task_avg=0.000103 mcu_task_stddev=0.000073 bytes_write=31909 bytes_read=266470 bytes_retransmit=9 bytes_invalid=0 send_seq=3777 receive_seq=3777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997600 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13507 bytes_read=526474 bytes_retransmit=9 bytes_invalid=0 send_seq=2197 receive_seq=2197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997708 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14047 bytes_read=42148 bytes_retransmit=9 bytes_invalid=0 send_seq=2188 receive_seq=2188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999461 Octopus_Pro_H723_V1.1: temp=32.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62619 bytes_read=957274 bytes_retransmit=0 bytes_invalid=0 send_seq=6285 receive_seq=6285 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998726 coil_temp=17.9 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=40.4 th1: temp=40.4 th2: temp=45.3 th3: temp=43.9 sysload=0.21 cputime=183.868 memavail=7399716 print_time=2100.699 buffer_time=2.012 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Testing frequency 13 Hz
Testing frequency 14 Hz
Stats 2077.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17730595 bytes_read=2107295 bytes_retransmit=9 bytes_invalid=0 send_seq=305547 receive_seq=305547 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015170 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=13300 bytes_read=42988 bytes_retransmit=0 bytes_invalid=0 send_seq=2188 receive_seq=2188 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999191 adj=49997318 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89327 bytes_read=2704901 bytes_retransmit=9 bytes_invalid=0 send_seq=11895 receive_seq=11895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997849 toolboard_t1: mcu_awake=0.097 mcu_task_avg=0.000103 mcu_task_stddev=0.000073 bytes_write=31985 bytes_read=269507 bytes_retransmit=9 bytes_invalid=0 send_seq=3788 receive_seq=3788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997600 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13513 bytes_read=526708 bytes_retransmit=9 bytes_invalid=0 send_seq=2198 receive_seq=2198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997708 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14053 bytes_read=42175 bytes_retransmit=9 bytes_invalid=0 send_seq=2189 receive_seq=2189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999467 Octopus_Pro_H723_V1.1: temp=32.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62625 bytes_read=957630 bytes_retransmit=0 bytes_invalid=0 send_seq=6286 receive_seq=6286 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998725 coil_temp=17.9 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=40.5 th1: temp=40.3 th2: temp=45.6 th3: temp=44.1 sysload=0.20 cputime=183.941 memavail=7399716 print_time=2101.971 buffer_time=2.284 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 15 Hz
Stats 2078.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17731796 bytes_read=2107785 bytes_retransmit=9 bytes_invalid=0 send_seq=305583 receive_seq=305583 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015163 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=13306 bytes_read=43004 bytes_retransmit=0 bytes_invalid=0 send_seq=2189 receive_seq=2189 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999191 adj=49997280 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89333 bytes_read=2705001 bytes_retransmit=9 bytes_invalid=0 send_seq=11896 receive_seq=11896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997795 toolboard_t1: mcu_awake=0.097 mcu_task_avg=0.000103 mcu_task_stddev=0.000073 bytes_write=32061 bytes_read=272564 bytes_retransmit=9 bytes_invalid=0 send_seq=3799 receive_seq=3799 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997573 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13519 bytes_read=526942 bytes_retransmit=9 bytes_invalid=0 send_seq=2199 receive_seq=2199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999523 adj=47997677 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14059 bytes_read=42191 bytes_retransmit=9 bytes_invalid=0 send_seq=2190 receive_seq=2190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999457 Octopus_Pro_H723_V1.1: temp=31.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62631 bytes_read=957986 bytes_retransmit=0 bytes_invalid=0 send_seq=6287 receive_seq=6287 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998697 coil_temp=17.9 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=40.8 th1: temp=40.4 th2: temp=45.6 th3: temp=44.2 sysload=0.20 cputime=184.010 memavail=7399720 print_time=2102.826 buffer_time=2.138 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 16 Hz
Stats 2079.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17733336 bytes_read=2108316 bytes_retransmit=9 bytes_invalid=0 send_seq=305625 receive_seq=305625 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015161 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=13318 bytes_read=43036 bytes_retransmit=0 bytes_invalid=0 send_seq=2191 receive_seq=2191 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999192 adj=49997294 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89345 bytes_read=2705159 bytes_retransmit=9 bytes_invalid=0 send_seq=11898 receive_seq=11898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997806 toolboard_t1: mcu_awake=0.097 mcu_task_avg=0.000103 mcu_task_stddev=0.000073 bytes_write=32143 bytes_read=275667 bytes_retransmit=9 bytes_invalid=0 send_seq=3811 receive_seq=3811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997583 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13531 bytes_read=527252 bytes_retransmit=9 bytes_invalid=0 send_seq=2201 receive_seq=2201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999522 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14071 bytes_read=42223 bytes_retransmit=9 bytes_invalid=0 send_seq=2192 receive_seq=2192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999458 Octopus_Pro_H723_V1.1: temp=32.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62643 bytes_read=958358 bytes_retransmit=0 bytes_invalid=0 send_seq=6289 receive_seq=6289 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998692 coil_temp=17.9 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=40.8 th1: temp=40.7 th2: temp=45.7 th3: temp=44.3 sysload=0.20 cputime=184.083 memavail=7399720 print_time=2103.791 buffer_time=2.102 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 17 Hz
Stats 2080.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17735089 bytes_read=2108900 bytes_retransmit=9 bytes_invalid=0 send_seq=305671 receive_seq=305671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=0 freq=400015155 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=13324 bytes_read=43052 bytes_retransmit=0 bytes_invalid=0 send_seq=2192 receive_seq=2192 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999192 adj=49997315 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89351 bytes_read=2705259 bytes_retransmit=9 bytes_invalid=0 send_seq=11899 receive_seq=11899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997791 toolboard_t1: mcu_awake=0.097 mcu_task_avg=0.000103 mcu_task_stddev=0.000073 bytes_write=32219 bytes_read=278723 bytes_retransmit=9 bytes_invalid=0 send_seq=3822 receive_seq=3822 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997581 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13537 bytes_read=527501 bytes_retransmit=9 bytes_invalid=0 send_seq=2202 receive_seq=2202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999522 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14077 bytes_read=42239 bytes_retransmit=9 bytes_invalid=0 send_seq=2193 receive_seq=2193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999455 Octopus_Pro_H723_V1.1: temp=31.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62649 bytes_read=958714 bytes_retransmit=0 bytes_invalid=0 send_seq=6290 receive_seq=6290 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998688 coil_temp=17.9 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=40.9 th1: temp=40.8 th2: temp=46.0 th3: temp=44.3 sysload=0.20 cputime=184.165 memavail=7400072 print_time=2104.994 buffer_time=2.305 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 18 Hz
Stats 2081.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17736521 bytes_read=2109410 bytes_retransmit=9 bytes_invalid=0 send_seq=305711 receive_seq=305711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015172 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=13330 bytes_read=43068 bytes_retransmit=0 bytes_invalid=0 send_seq=2193 receive_seq=2193 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999193 adj=49997318 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89357 bytes_read=2705359 bytes_retransmit=9 bytes_invalid=0 send_seq=11900 receive_seq=11900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997866 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32295 bytes_read=281796 bytes_retransmit=9 bytes_invalid=0 send_seq=3833 receive_seq=3833 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997588 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13543 bytes_read=527735 bytes_retransmit=9 bytes_invalid=0 send_seq=2203 receive_seq=2203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999522 adj=47997690 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14083 bytes_read=42255 bytes_retransmit=9 bytes_invalid=0 send_seq=2194 receive_seq=2194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999457 Octopus_Pro_H723_V1.1: temp=31.6 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62655 bytes_read=959070 bytes_retransmit=0 bytes_invalid=0 send_seq=6291 receive_seq=6291 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998691 coil_temp=17.9 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=41.2 th1: temp=40.7 th2: temp=45.5 th3: temp=44.3 sysload=0.20 cputime=184.235 memavail=7400072 print_time=2105.940 buffer_time=2.250 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 19 Hz
Stats 2082.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17738081 bytes_read=2109920 bytes_retransmit=9 bytes_invalid=0 send_seq=305752 receive_seq=305752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015165 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13336 bytes_read=43097 bytes_retransmit=0 bytes_invalid=0 send_seq=2194 receive_seq=2194 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999192 adj=49997295 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89363 bytes_read=2705487 bytes_retransmit=9 bytes_invalid=0 send_seq=11901 receive_seq=11901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997818 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32371 bytes_read=284881 bytes_retransmit=9 bytes_invalid=0 send_seq=3844 receive_seq=3844 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997595 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13549 bytes_read=528029 bytes_retransmit=9 bytes_invalid=0 send_seq=2204 receive_seq=2204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14089 bytes_read=42282 bytes_retransmit=9 bytes_invalid=0 send_seq=2195 receive_seq=2195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999449 Octopus_Pro_H723_V1.1: temp=31.8 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62661 bytes_read=959426 bytes_retransmit=0 bytes_invalid=0 send_seq=6292 receive_seq=6292 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998674 coil_temp=17.9 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=41.2 th1: temp=41.2 th2: temp=46.2 th3: temp=44.6 sysload=0.18 cputime=184.305 memavail=7400072 print_time=2106.761 buffer_time=2.071 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Testing frequency 20 Hz
Stats 2083.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17739602 bytes_read=2110469 bytes_retransmit=9 bytes_invalid=0 send_seq=305794 receive_seq=305794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015159 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13342 bytes_read=43113 bytes_retransmit=0 bytes_invalid=0 send_seq=2195 receive_seq=2195 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999191 adj=49997293 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89369 bytes_read=2705587 bytes_retransmit=9 bytes_invalid=0 send_seq=11902 receive_seq=11902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997850 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32447 bytes_read=287997 bytes_retransmit=9 bytes_invalid=0 send_seq=3855 receive_seq=3855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997622 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13555 bytes_read=528263 bytes_retransmit=9 bytes_invalid=0 send_seq=2205 receive_seq=2205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999522 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14095 bytes_read=42298 bytes_retransmit=9 bytes_invalid=0 send_seq=2196 receive_seq=2196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999451 Octopus_Pro_H723_V1.1: temp=31.6 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62667 bytes_read=959782 bytes_retransmit=0 bytes_invalid=0 send_seq=6293 receive_seq=6293 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998683 coil_temp=17.9 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=41.1 th1: temp=40.6 th2: temp=46.1 th3: temp=44.5 sysload=0.18 cputime=184.378 memavail=7399824 print_time=2107.746 buffer_time=2.055 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 21 Hz
Stats 2084.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17741650 bytes_read=2111024 bytes_retransmit=9 bytes_invalid=0 send_seq=305843 receive_seq=305843 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015155 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13348 bytes_read=43129 bytes_retransmit=0 bytes_invalid=0 send_seq=2196 receive_seq=2196 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999191 adj=49997293 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89375 bytes_read=2705701 bytes_retransmit=9 bytes_invalid=0 send_seq=11903 receive_seq=11903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997894 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32523 bytes_read=291054 bytes_retransmit=9 bytes_invalid=0 send_seq=3866 receive_seq=3866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997700 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13561 bytes_read=528497 bytes_retransmit=9 bytes_invalid=0 send_seq=2206 receive_seq=2206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999522 adj=47997693 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14101 bytes_read=42314 bytes_retransmit=9 bytes_invalid=0 send_seq=2197 receive_seq=2197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999455 Octopus_Pro_H723_V1.1: temp=31.5 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62673 bytes_read=960138 bytes_retransmit=0 bytes_invalid=0 send_seq=6294 receive_seq=6294 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998688 coil_temp=17.9 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=41.3 th1: temp=40.8 th2: temp=46.2 th3: temp=44.5 sysload=0.18 cputime=184.452 memavail=7399824 print_time=2108.986 buffer_time=2.292 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 22 Hz
Stats 2085.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17743349 bytes_read=2111569 bytes_retransmit=9 bytes_invalid=0 send_seq=305887 receive_seq=305887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015147 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13354 bytes_read=43145 bytes_retransmit=0 bytes_invalid=0 send_seq=2197 receive_seq=2197 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999191 adj=49997299 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89381 bytes_read=2705829 bytes_retransmit=9 bytes_invalid=0 send_seq=11904 receive_seq=11904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997905 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32599 bytes_read=294138 bytes_retransmit=9 bytes_invalid=0 send_seq=3877 receive_seq=3877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997748 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13567 bytes_read=528806 bytes_retransmit=9 bytes_invalid=0 send_seq=2207 receive_seq=2207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999522 adj=47997705 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14107 bytes_read=42330 bytes_retransmit=9 bytes_invalid=0 send_seq=2198 receive_seq=2198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999457 Octopus_Pro_H723_V1.1: temp=31.5 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62679 bytes_read=960494 bytes_retransmit=0 bytes_invalid=0 send_seq=6295 receive_seq=6295 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998691 coil_temp=17.9 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=41.3 th1: temp=41.2 th2: temp=46.3 th3: temp=44.5 sysload=0.18 cputime=184.595 memavail=7399824 print_time=2109.841 buffer_time=2.143 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Testing frequency 23 Hz
Stats 2086.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17744900 bytes_read=2112123 bytes_retransmit=9 bytes_invalid=0 send_seq=305930 receive_seq=305930 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015153 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13360 bytes_read=43161 bytes_retransmit=0 bytes_invalid=0 send_seq=2198 receive_seq=2198 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999192 adj=49997314 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89387 bytes_read=2705929 bytes_retransmit=9 bytes_invalid=0 send_seq=11905 receive_seq=11905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997905 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32675 bytes_read=297214 bytes_retransmit=9 bytes_invalid=0 send_seq=3888 receive_seq=3888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997801 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13573 bytes_read=529040 bytes_retransmit=9 bytes_invalid=0 send_seq=2208 receive_seq=2208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997717 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14113 bytes_read=42346 bytes_retransmit=9 bytes_invalid=0 send_seq=2199 receive_seq=2199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999459 Octopus_Pro_H723_V1.1: temp=31.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=30.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62685 bytes_read=960850 bytes_retransmit=0 bytes_invalid=0 send_seq=6296 receive_seq=6296 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998727 coil_temp=17.9 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=41.7 th1: temp=41.2 th2: temp=46.3 th3: temp=44.8 sysload=0.18 cputime=184.672 memavail=7399572 print_time=2110.761 buffer_time=2.063 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 24 Hz
Stats 2087.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17747084 bytes_read=2112688 bytes_retransmit=9 bytes_invalid=0 send_seq=305981 receive_seq=305981 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015153 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13366 bytes_read=43190 bytes_retransmit=0 bytes_invalid=0 send_seq=2199 receive_seq=2199 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999192 adj=49997313 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89393 bytes_read=2706029 bytes_retransmit=9 bytes_invalid=0 send_seq=11906 receive_seq=11906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997857 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32751 bytes_read=300329 bytes_retransmit=9 bytes_invalid=0 send_seq=3899 receive_seq=3899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997744 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13579 bytes_read=529274 bytes_retransmit=9 bytes_invalid=0 send_seq=2209 receive_seq=2209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997702 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14119 bytes_read=42373 bytes_retransmit=9 bytes_invalid=0 send_seq=2200 receive_seq=2200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999478 Octopus_Pro_H723_V1.1: temp=31.4 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62691 bytes_read=961206 bytes_retransmit=0 bytes_invalid=0 send_seq=6297 receive_seq=6297 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998715 coil_temp=17.8 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=41.5 th1: temp=41.2 th2: temp=46.4 th3: temp=44.7 sysload=0.16 cputime=184.749 memavail=7399572 print_time=2111.994 buffer_time=2.292 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 25 Hz
Stats 2088.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17748895 bytes_read=2113228 bytes_retransmit=9 bytes_invalid=0 send_seq=306027 receive_seq=306027 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=0 freq=400015150 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13372 bytes_read=43206 bytes_retransmit=0 bytes_invalid=0 send_seq=2200 receive_seq=2200 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999193 adj=49997309 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89399 bytes_read=2706157 bytes_retransmit=9 bytes_invalid=0 send_seq=11907 receive_seq=11907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997889 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32827 bytes_read=303413 bytes_retransmit=9 bytes_invalid=0 send_seq=3910 receive_seq=3910 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997697 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13585 bytes_read=529568 bytes_retransmit=9 bytes_invalid=0 send_seq=2210 receive_seq=2210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997739 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14125 bytes_read=42389 bytes_retransmit=9 bytes_invalid=0 send_seq=2201 receive_seq=2201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999478 Octopus_Pro_H723_V1.1: temp=31.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62697 bytes_read=961562 bytes_retransmit=0 bytes_invalid=0 send_seq=6298 receive_seq=6298 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998706 coil_temp=17.8 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=41.5 th1: temp=41.3 th2: temp=46.5 th3: temp=44.8 sysload=0.16 cputime=184.822 memavail=7399572 print_time=2112.871 buffer_time=2.167 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.3 pwm=0.000
Testing frequency 26 Hz
Stats 2089.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17750762 bytes_read=2113802 bytes_retransmit=9 bytes_invalid=0 send_seq=306074 receive_seq=306074 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015170 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13378 bytes_read=43222 bytes_retransmit=0 bytes_invalid=0 send_seq=2201 receive_seq=2201 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999193 adj=49997326 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89405 bytes_read=2706271 bytes_retransmit=9 bytes_invalid=0 send_seq=11908 receive_seq=11908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997879 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32903 bytes_read=306471 bytes_retransmit=9 bytes_invalid=0 send_seq=3921 receive_seq=3921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997666 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13591 bytes_read=529802 bytes_retransmit=9 bytes_invalid=0 send_seq=2211 receive_seq=2211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997734 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14131 bytes_read=42405 bytes_retransmit=9 bytes_invalid=0 send_seq=2202 receive_seq=2202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999474 Octopus_Pro_H723_V1.1: temp=31.4 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62703 bytes_read=961918 bytes_retransmit=0 bytes_invalid=0 send_seq=6299 receive_seq=6299 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998698 coil_temp=17.8 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=41.8 th1: temp=41.3 th2: temp=46.2 th3: temp=44.7 sysload=0.16 cputime=184.897 memavail=7399596 print_time=2113.838 buffer_time=2.132 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 27 Hz
Stats 2090.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17752516 bytes_read=2114357 bytes_retransmit=9 bytes_invalid=0 send_seq=306120 receive_seq=306120 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015175 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13384 bytes_read=43238 bytes_retransmit=0 bytes_invalid=0 send_seq=2202 receive_seq=2202 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999193 adj=49997287 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89411 bytes_read=2706371 bytes_retransmit=9 bytes_invalid=0 send_seq=11909 receive_seq=11909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997802 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=32979 bytes_read=309527 bytes_retransmit=9 bytes_invalid=0 send_seq=3932 receive_seq=3932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997592 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13597 bytes_read=530051 bytes_retransmit=9 bytes_invalid=0 send_seq=2212 receive_seq=2212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999523 adj=47997698 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14137 bytes_read=42421 bytes_retransmit=9 bytes_invalid=0 send_seq=2203 receive_seq=2203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999463 Octopus_Pro_H723_V1.1: temp=31.3 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62709 bytes_read=962274 bytes_retransmit=0 bytes_invalid=0 send_seq=6300 receive_seq=6300 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998672 coil_temp=17.8 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=41.7 th1: temp=41.4 th2: temp=46.4 th3: temp=44.8 sysload=0.16 cputime=184.974 memavail=7399596 print_time=2114.697 buffer_time=1.988 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 28 Hz
Stats 2091.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17754822 bytes_read=2114942 bytes_retransmit=9 bytes_invalid=0 send_seq=306175 receive_seq=306175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=0 freq=400015174 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13390 bytes_read=43254 bytes_retransmit=0 bytes_invalid=0 send_seq=2203 receive_seq=2203 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999194 adj=49997290 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89417 bytes_read=2706499 bytes_retransmit=9 bytes_invalid=0 send_seq=11910 receive_seq=11910 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997766 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33055 bytes_read=312630 bytes_retransmit=9 bytes_invalid=0 send_seq=3943 receive_seq=3943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997557 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13603 bytes_read=530345 bytes_retransmit=9 bytes_invalid=0 send_seq=2213 receive_seq=2213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999523 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14143 bytes_read=42437 bytes_retransmit=9 bytes_invalid=0 send_seq=2204 receive_seq=2204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999459 Octopus_Pro_H723_V1.1: temp=31.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62715 bytes_read=962630 bytes_retransmit=0 bytes_invalid=0 send_seq=6301 receive_seq=6301 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998666 coil_temp=17.8 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=42.4 th1: temp=41.2 th2: temp=46.4 th3: temp=44.8 sysload=0.16 cputime=185.054 memavail=7399596 print_time=2115.922 buffer_time=2.212 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 29 Hz
Stats 2092.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17756699 bytes_read=2115501 bytes_retransmit=9 bytes_invalid=0 send_seq=306219 receive_seq=306219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015175 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13396 bytes_read=43283 bytes_retransmit=0 bytes_invalid=0 send_seq=2204 receive_seq=2204 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999194 adj=49997295 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89423 bytes_read=2706599 bytes_retransmit=9 bytes_invalid=0 send_seq=11911 receive_seq=11911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997754 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33131 bytes_read=315745 bytes_retransmit=9 bytes_invalid=0 send_seq=3954 receive_seq=3954 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997568 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13609 bytes_read=530579 bytes_retransmit=9 bytes_invalid=0 send_seq=2214 receive_seq=2214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999522 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14149 bytes_read=42464 bytes_retransmit=9 bytes_invalid=0 send_seq=2205 receive_seq=2205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999458 Octopus_Pro_H723_V1.1: temp=31.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62721 bytes_read=962986 bytes_retransmit=0 bytes_invalid=0 send_seq=6302 receive_seq=6302 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998680 coil_temp=17.8 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=41.3 th1: temp=41.7 th2: temp=46.3 th3: temp=44.9 sysload=0.15 cputime=185.129 memavail=7399596 print_time=2116.848 buffer_time=2.136 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 30 Hz
Stats 2093.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17758506 bytes_read=2116026 bytes_retransmit=9 bytes_invalid=0 send_seq=306263 receive_seq=306263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015176 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13402 bytes_read=43299 bytes_retransmit=0 bytes_invalid=0 send_seq=2205 receive_seq=2205 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999195 adj=49997301 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89429 bytes_read=2706699 bytes_retransmit=9 bytes_invalid=0 send_seq=11912 receive_seq=11912 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997811 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33207 bytes_read=318801 bytes_retransmit=9 bytes_invalid=0 send_seq=3965 receive_seq=3965 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13615 bytes_read=530813 bytes_retransmit=9 bytes_invalid=0 send_seq=2215 receive_seq=2215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999522 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14155 bytes_read=42480 bytes_retransmit=9 bytes_invalid=0 send_seq=2206 receive_seq=2206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999456 Octopus_Pro_H723_V1.1: temp=31.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62727 bytes_read=963342 bytes_retransmit=0 bytes_invalid=0 send_seq=6303 receive_seq=6303 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998678 coil_temp=17.8 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=42.4 th1: temp=41.8 th2: temp=46.4 th3: temp=44.9 sysload=0.15 cputime=185.203 memavail=7399596 print_time=2117.728 buffer_time=2.014 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 31 Hz
Stats 2094.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17760895 bytes_read=2116606 bytes_retransmit=9 bytes_invalid=0 send_seq=306317 receive_seq=306317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015178 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13408 bytes_read=43315 bytes_retransmit=0 bytes_invalid=0 send_seq=2206 receive_seq=2206 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999195 adj=49997313 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89435 bytes_read=2706841 bytes_retransmit=9 bytes_invalid=0 send_seq=11913 receive_seq=11913 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997782 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33276 bytes_read=321863 bytes_retransmit=9 bytes_invalid=0 send_seq=3975 receive_seq=3975 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997536 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13621 bytes_read=531107 bytes_retransmit=9 bytes_invalid=0 send_seq=2216 receive_seq=2216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999522 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14161 bytes_read=42496 bytes_retransmit=9 bytes_invalid=0 send_seq=2207 receive_seq=2207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999454 Octopus_Pro_H723_V1.1: temp=31.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62733 bytes_read=963698 bytes_retransmit=0 bytes_invalid=0 send_seq=6304 receive_seq=6304 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998698 coil_temp=17.8 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=41.8 th1: temp=41.9 th2: temp=46.9 th3: temp=44.9 sysload=0.15 cputime=185.283 memavail=7399596 print_time=2118.930 buffer_time=2.215 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 32 Hz
Stats 2095.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17762965 bytes_read=2117195 bytes_retransmit=9 bytes_invalid=0 send_seq=306364 receive_seq=306364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015183 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13414 bytes_read=43331 bytes_retransmit=0 bytes_invalid=0 send_seq=2207 receive_seq=2207 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999197 adj=49997310 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89441 bytes_read=2706941 bytes_retransmit=9 bytes_invalid=0 send_seq=11914 receive_seq=11914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997759 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33352 bytes_read=324923 bytes_retransmit=9 bytes_invalid=0 send_seq=3986 receive_seq=3986 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997536 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13627 bytes_read=531356 bytes_retransmit=9 bytes_invalid=0 send_seq=2217 receive_seq=2217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999522 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14167 bytes_read=42512 bytes_retransmit=9 bytes_invalid=0 send_seq=2208 receive_seq=2208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999456 Octopus_Pro_H723_V1.1: temp=31.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62739 bytes_read=964054 bytes_retransmit=0 bytes_invalid=0 send_seq=6305 receive_seq=6305 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998695 coil_temp=17.8 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=42.1 th1: temp=41.8 th2: temp=46.8 th3: temp=45.1 sysload=0.15 cputime=185.356 memavail=7399608 print_time=2119.871 buffer_time=2.155 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Testing frequency 33 Hz
Stats 2096.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17764816 bytes_read=2117730 bytes_retransmit=9 bytes_invalid=0 send_seq=306409 receive_seq=306409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015191 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13420 bytes_read=43347 bytes_retransmit=0 bytes_invalid=0 send_seq=2208 receive_seq=2208 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999196 adj=49997315 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89447 bytes_read=2707041 bytes_retransmit=9 bytes_invalid=0 send_seq=11915 receive_seq=11915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997739 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33428 bytes_read=327997 bytes_retransmit=9 bytes_invalid=0 send_seq=3997 receive_seq=3997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997521 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13633 bytes_read=531590 bytes_retransmit=9 bytes_invalid=0 send_seq=2218 receive_seq=2218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999522 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14173 bytes_read=42528 bytes_retransmit=9 bytes_invalid=0 send_seq=2209 receive_seq=2209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999453 Octopus_Pro_H723_V1.1: temp=30.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62745 bytes_read=964410 bytes_retransmit=0 bytes_invalid=0 send_seq=6306 receive_seq=6306 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998682 coil_temp=17.8 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=41.7 th1: temp=41.5 th2: temp=46.7 th3: temp=45.1 sysload=0.15 cputime=185.432 memavail=7402936 print_time=2120.769 buffer_time=2.053 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 34 Hz
Stats 2097.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17767037 bytes_read=2118305 bytes_retransmit=9 bytes_invalid=0 send_seq=306462 receive_seq=306462 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015200 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13426 bytes_read=43376 bytes_retransmit=0 bytes_invalid=0 send_seq=2209 receive_seq=2209 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999197 adj=49997291 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89453 bytes_read=2707169 bytes_retransmit=9 bytes_invalid=0 send_seq=11916 receive_seq=11916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997718 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33504 bytes_read=331081 bytes_retransmit=9 bytes_invalid=0 send_seq=4008 receive_seq=4008 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997495 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13639 bytes_read=531884 bytes_retransmit=9 bytes_invalid=0 send_seq=2219 receive_seq=2219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999522 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14179 bytes_read=42555 bytes_retransmit=9 bytes_invalid=0 send_seq=2210 receive_seq=2210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999453 Octopus_Pro_H723_V1.1: temp=31.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62751 bytes_read=964766 bytes_retransmit=0 bytes_invalid=0 send_seq=6307 receive_seq=6307 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998682 coil_temp=17.8 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=42.2 th1: temp=41.7 th2: temp=46.7 th3: temp=45.2 sysload=0.22 cputime=185.516 memavail=7402296 print_time=2121.710 buffer_time=1.993 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 35 Hz
Stats 2098.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17769621 bytes_read=2118944 bytes_retransmit=9 bytes_invalid=0 send_seq=306522 receive_seq=306522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=0 freq=400015198 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13432 bytes_read=43392 bytes_retransmit=0 bytes_invalid=0 send_seq=2210 receive_seq=2210 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999197 adj=49997285 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89459 bytes_read=2707269 bytes_retransmit=9 bytes_invalid=0 send_seq=11917 receive_seq=11917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997687 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33580 bytes_read=334139 bytes_retransmit=9 bytes_invalid=0 send_seq=4019 receive_seq=4019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997473 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13645 bytes_read=532118 bytes_retransmit=9 bytes_invalid=0 send_seq=2220 receive_seq=2220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999522 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14185 bytes_read=42571 bytes_retransmit=9 bytes_invalid=0 send_seq=2211 receive_seq=2211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999449 Octopus_Pro_H723_V1.1: temp=31.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62757 bytes_read=965122 bytes_retransmit=0 bytes_invalid=0 send_seq=6308 receive_seq=6308 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998668 coil_temp=17.8 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=43.1 th1: temp=42.0 th2: temp=46.9 th3: temp=45.3 sysload=0.22 cputime=185.597 memavail=7402320 print_time=2122.918 buffer_time=2.201 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 36 Hz
Stats 2099.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17771528 bytes_read=2119499 bytes_retransmit=9 bytes_invalid=0 send_seq=306571 receive_seq=306571 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015194 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13438 bytes_read=43408 bytes_retransmit=0 bytes_invalid=0 send_seq=2211 receive_seq=2211 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999198 adj=49997302 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89465 bytes_read=2707383 bytes_retransmit=9 bytes_invalid=0 send_seq=11918 receive_seq=11918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997703 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33656 bytes_read=337253 bytes_retransmit=9 bytes_invalid=0 send_seq=4030 receive_seq=4030 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997503 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13651 bytes_read=532352 bytes_retransmit=9 bytes_invalid=0 send_seq=2221 receive_seq=2221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999522 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14191 bytes_read=42587 bytes_retransmit=9 bytes_invalid=0 send_seq=2212 receive_seq=2212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999451 Octopus_Pro_H723_V1.1: temp=30.8 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62763 bytes_read=965478 bytes_retransmit=0 bytes_invalid=0 send_seq=6309 receive_seq=6309 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998713 coil_temp=17.8 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=42.4 th1: temp=42.3 th2: temp=46.8 th3: temp=45.2 sysload=0.22 cputime=185.673 memavail=7402068 print_time=2123.796 buffer_time=2.078 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2100.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17773915 bytes_read=2120099 bytes_retransmit=9 bytes_invalid=0 send_seq=306626 receive_seq=306626 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015209 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13444 bytes_read=43424 bytes_retransmit=0 bytes_invalid=0 send_seq=2212 receive_seq=2212 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999200 adj=49997318 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89471 bytes_read=2707511 bytes_retransmit=9 bytes_invalid=0 send_seq=11919 receive_seq=11919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997706 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33732 bytes_read=340338 bytes_retransmit=9 bytes_invalid=0 send_seq=4041 receive_seq=4041 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997507 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13657 bytes_read=532661 bytes_retransmit=9 bytes_invalid=0 send_seq=2222 receive_seq=2222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14197 bytes_read=42603 bytes_retransmit=9 bytes_invalid=0 send_seq=2213 receive_seq=2213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999453 Octopus_Pro_H723_V1.1: temp=30.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62769 bytes_read=965834 bytes_retransmit=0 bytes_invalid=0 send_seq=6310 receive_seq=6310 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998712 coil_temp=17.8 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=42.4 th1: temp=41.9 th2: temp=46.7 th3: temp=45.1 sysload=0.22 cputime=185.749 memavail=7402068 print_time=2124.748 buffer_time=2.029 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 37 Hz
Testing frequency 38 Hz
Stats 2101.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17776639 bytes_read=2120738 bytes_retransmit=9 bytes_invalid=0 send_seq=306686 receive_seq=306686 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=15 upcoming_bytes=0 freq=400015223 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13450 bytes_read=43440 bytes_retransmit=0 bytes_invalid=0 send_seq=2213 receive_seq=2213 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999200 adj=49997317 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89477 bytes_read=2707611 bytes_retransmit=9 bytes_invalid=0 send_seq=11920 receive_seq=11920 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997669 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33808 bytes_read=343413 bytes_retransmit=9 bytes_invalid=0 send_seq=4052 receive_seq=4052 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997477 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13663 bytes_read=532895 bytes_retransmit=9 bytes_invalid=0 send_seq=2223 receive_seq=2223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14203 bytes_read=42619 bytes_retransmit=9 bytes_invalid=0 send_seq=2214 receive_seq=2214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999447 Octopus_Pro_H723_V1.1: temp=30.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62775 bytes_read=966190 bytes_retransmit=0 bytes_invalid=0 send_seq=6311 receive_seq=6311 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998709 coil_temp=17.8 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=42.4 th1: temp=41.7 th2: temp=46.7 th3: temp=45.2 sysload=0.22 cputime=185.831 memavail=7402068 print_time=2125.932 buffer_time=2.213 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 39 Hz
Stats 2102.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17778544 bytes_read=2121278 bytes_retransmit=9 bytes_invalid=0 send_seq=306732 receive_seq=306732 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015268 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13456 bytes_read=43469 bytes_retransmit=0 bytes_invalid=0 send_seq=2214 receive_seq=2214 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999200 adj=49997289 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89483 bytes_read=2707711 bytes_retransmit=9 bytes_invalid=0 send_seq=11921 receive_seq=11921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997658 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33884 bytes_read=346471 bytes_retransmit=9 bytes_invalid=0 send_seq=4063 receive_seq=4063 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997471 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13669 bytes_read=533129 bytes_retransmit=9 bytes_invalid=0 send_seq=2224 receive_seq=2224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14209 bytes_read=42646 bytes_retransmit=9 bytes_invalid=0 send_seq=2215 receive_seq=2215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999444 Octopus_Pro_H723_V1.1: temp=30.8 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62781 bytes_read=966546 bytes_retransmit=0 bytes_invalid=0 send_seq=6312 receive_seq=6312 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998693 coil_temp=17.8 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=42.4 th1: temp=42.2 th2: temp=46.9 th3: temp=45.1 sysload=0.20 cputime=185.907 memavail=7401856 print_time=2126.819 buffer_time=2.100 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 40 Hz
Stats 2103.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17781001 bytes_read=2121878 bytes_retransmit=9 bytes_invalid=0 send_seq=306790 receive_seq=306790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015271 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13462 bytes_read=43485 bytes_retransmit=0 bytes_invalid=0 send_seq=2215 receive_seq=2215 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999205 adj=49997218 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89489 bytes_read=2707839 bytes_retransmit=9 bytes_invalid=0 send_seq=11922 receive_seq=11922 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997573 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=33960 bytes_read=349561 bytes_retransmit=9 bytes_invalid=0 send_seq=4074 receive_seq=4074 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000033 adj=63997384 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13675 bytes_read=533423 bytes_retransmit=9 bytes_invalid=0 send_seq=2225 receive_seq=2225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997573 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14215 bytes_read=42662 bytes_retransmit=9 bytes_invalid=0 send_seq=2216 receive_seq=2216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999429 Octopus_Pro_H723_V1.1: temp=30.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62787 bytes_read=966902 bytes_retransmit=0 bytes_invalid=0 send_seq=6313 receive_seq=6313 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998683 coil_temp=17.8 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=42.6 th1: temp=42.3 th2: temp=46.9 th3: temp=45.4 sysload=0.20 cputime=185.986 memavail=7401856 print_time=2127.773 buffer_time=2.054 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Testing frequency 41 Hz
Stats 2104.2: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17783907 bytes_read=2122537 bytes_retransmit=9 bytes_invalid=0 send_seq=306855 receive_seq=306855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=23 upcoming_bytes=0 freq=400015270 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13468 bytes_read=43501 bytes_retransmit=0 bytes_invalid=0 send_seq=2216 receive_seq=2216 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999205 adj=49997286 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89495 bytes_read=2707939 bytes_retransmit=9 bytes_invalid=0 send_seq=11923 receive_seq=11923 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997611 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34036 bytes_read=352617 bytes_retransmit=9 bytes_invalid=0 send_seq=4085 receive_seq=4085 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000033 adj=63997396 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13681 bytes_read=533657 bytes_retransmit=9 bytes_invalid=0 send_seq=2226 receive_seq=2226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997582 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14221 bytes_read=42678 bytes_retransmit=9 bytes_invalid=0 send_seq=2217 receive_seq=2217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999433 Octopus_Pro_H723_V1.1: temp=30.6 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62793 bytes_read=967258 bytes_retransmit=0 bytes_invalid=0 send_seq=6314 receive_seq=6314 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998669 coil_temp=17.8 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=42.6 th1: temp=42.1 th2: temp=47.0 th3: temp=45.1 sysload=0.20 cputime=186.069 memavail=7401856 print_time=2128.980 buffer_time=2.260 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 42 Hz
Stats 2105.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17785947 bytes_read=2123117 bytes_retransmit=9 bytes_invalid=0 send_seq=306906 receive_seq=306906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015276 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13474 bytes_read=43517 bytes_retransmit=0 bytes_invalid=0 send_seq=2217 receive_seq=2217 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999206 adj=49997297 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89501 bytes_read=2708053 bytes_retransmit=9 bytes_invalid=0 send_seq=11924 receive_seq=11924 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997663 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34112 bytes_read=355677 bytes_retransmit=9 bytes_invalid=0 send_seq=4096 receive_seq=4096 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997447 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13687 bytes_read=533906 bytes_retransmit=9 bytes_invalid=0 send_seq=2227 receive_seq=2227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997613 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14227 bytes_read=42694 bytes_retransmit=9 bytes_invalid=0 send_seq=2218 receive_seq=2218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999439 Octopus_Pro_H723_V1.1: temp=30.6 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62799 bytes_read=967603 bytes_retransmit=0 bytes_invalid=0 send_seq=6315 receive_seq=6315 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998666 coil_temp=17.8 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=42.6 th1: temp=41.8 th2: temp=46.9 th3: temp=45.2 sysload=0.20 cputime=186.146 memavail=7401856 print_time=2129.862 buffer_time=2.142 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 43 Hz
Stats 2106.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17788538 bytes_read=2123722 bytes_retransmit=9 bytes_invalid=0 send_seq=306965 receive_seq=306965 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015294 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13480 bytes_read=43533 bytes_retransmit=0 bytes_invalid=0 send_seq=2218 receive_seq=2218 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999207 adj=49997294 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89507 bytes_read=2708181 bytes_retransmit=9 bytes_invalid=0 send_seq=11925 receive_seq=11925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997648 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34188 bytes_read=358837 bytes_retransmit=9 bytes_invalid=0 send_seq=4107 receive_seq=4107 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997440 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13693 bytes_read=534200 bytes_retransmit=9 bytes_invalid=0 send_seq=2228 receive_seq=2228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997609 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14233 bytes_read=42710 bytes_retransmit=9 bytes_invalid=0 send_seq=2219 receive_seq=2219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999438 Octopus_Pro_H723_V1.1: temp=30.5 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62805 bytes_read=967948 bytes_retransmit=0 bytes_invalid=0 send_seq=6316 receive_seq=6316 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998651 coil_temp=17.8 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=42.8 th1: temp=42.3 th2: temp=47.1 th3: temp=45.4 sysload=0.20 cputime=186.227 memavail=7400888 print_time=2130.778 buffer_time=2.058 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Testing frequency 44 Hz
Stats 2107.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17791487 bytes_read=2124386 bytes_retransmit=9 bytes_invalid=0 send_seq=307030 receive_seq=307030 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=23 upcoming_bytes=0 freq=400015314 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13486 bytes_read=43562 bytes_retransmit=0 bytes_invalid=0 send_seq=2219 receive_seq=2219 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997278 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89513 bytes_read=2708281 bytes_retransmit=9 bytes_invalid=0 send_seq=11926 receive_seq=11926 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997610 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34264 bytes_read=361894 bytes_retransmit=9 bytes_invalid=0 send_seq=4118 receive_seq=4118 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997422 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13699 bytes_read=534434 bytes_retransmit=9 bytes_invalid=0 send_seq=2229 receive_seq=2229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997590 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14239 bytes_read=42737 bytes_retransmit=9 bytes_invalid=0 send_seq=2220 receive_seq=2220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999434 Octopus_Pro_H723_V1.1: temp=30.5 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62811 bytes_read=968292 bytes_retransmit=0 bytes_invalid=0 send_seq=6317 receive_seq=6317 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998627 coil_temp=17.8 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=42.3 th1: temp=42.4 th2: temp=47.2 th3: temp=45.5 sysload=0.18 cputime=186.311 memavail=7400888 print_time=2131.993 buffer_time=2.272 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 45 Hz
Stats 2108.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17793524 bytes_read=2124951 bytes_retransmit=9 bytes_invalid=0 send_seq=307081 receive_seq=307081 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=0 freq=400015320 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13492 bytes_read=43578 bytes_retransmit=0 bytes_invalid=0 send_seq=2220 receive_seq=2220 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999207 adj=49997263 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89519 bytes_read=2708381 bytes_retransmit=9 bytes_invalid=0 send_seq=11927 receive_seq=11927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997614 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34340 bytes_read=364950 bytes_retransmit=9 bytes_invalid=0 send_seq=4129 receive_seq=4129 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997426 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13705 bytes_read=534668 bytes_retransmit=9 bytes_invalid=0 send_seq=2230 receive_seq=2230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997598 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14245 bytes_read=42753 bytes_retransmit=9 bytes_invalid=0 send_seq=2221 receive_seq=2221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999435 Octopus_Pro_H723_V1.1: temp=30.4 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62817 bytes_read=968637 bytes_retransmit=0 bytes_invalid=0 send_seq=6318 receive_seq=6318 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998622 coil_temp=17.8 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=42.2 th1: temp=42.2 th2: temp=47.4 th3: temp=45.3 sysload=0.18 cputime=186.389 memavail=7400888 print_time=2132.877 buffer_time=2.155 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 46 Hz
Stats 2109.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17796214 bytes_read=2125561 bytes_retransmit=9 bytes_invalid=0 send_seq=307141 receive_seq=307141 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015330 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13498 bytes_read=43594 bytes_retransmit=0 bytes_invalid=0 send_seq=2221 receive_seq=2221 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999207 adj=49997252 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89525 bytes_read=2708509 bytes_retransmit=9 bytes_invalid=0 send_seq=11928 receive_seq=11928 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997633 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34409 bytes_read=368012 bytes_retransmit=9 bytes_invalid=0 send_seq=4139 receive_seq=4139 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000031 adj=63997421 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13711 bytes_read=534962 bytes_retransmit=9 bytes_invalid=0 send_seq=2231 receive_seq=2231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997597 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14251 bytes_read=42769 bytes_retransmit=9 bytes_invalid=0 send_seq=2222 receive_seq=2222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999435 Octopus_Pro_H723_V1.1: temp=30.5 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62823 bytes_read=968982 bytes_retransmit=0 bytes_invalid=0 send_seq=6319 receive_seq=6319 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998622 coil_temp=17.8 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=42.8 th1: temp=42.5 th2: temp=47.1 th3: temp=45.5 sysload=0.18 cputime=186.468 memavail=7400888 print_time=2133.799 buffer_time=2.077 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 47 Hz
Stats 2110.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17799187 bytes_read=2126245 bytes_retransmit=9 bytes_invalid=0 send_seq=307207 receive_seq=307207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015347 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13504 bytes_read=43610 bytes_retransmit=0 bytes_invalid=0 send_seq=2222 receive_seq=2222 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999207 adj=49997236 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89531 bytes_read=2708623 bytes_retransmit=9 bytes_invalid=0 send_seq=11929 receive_seq=11929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997619 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34485 bytes_read=371068 bytes_retransmit=9 bytes_invalid=0 send_seq=4150 receive_seq=4150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997433 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13717 bytes_read=535211 bytes_retransmit=9 bytes_invalid=0 send_seq=2232 receive_seq=2232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997593 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14257 bytes_read=42785 bytes_retransmit=9 bytes_invalid=0 send_seq=2223 receive_seq=2223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999439 Octopus_Pro_H723_V1.1: temp=30.4 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62829 bytes_read=969327 bytes_retransmit=0 bytes_invalid=0 send_seq=6320 receive_seq=6320 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998615 coil_temp=17.8 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=42.6 th1: temp=42.8 th2: temp=47.1 th3: temp=45.4 sysload=0.18 cputime=186.554 memavail=7400888 print_time=2135.010 buffer_time=2.287 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 48 Hz
Stats 2111.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17801315 bytes_read=2126820 bytes_retransmit=9 bytes_invalid=0 send_seq=307260 receive_seq=307260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=47 upcoming_bytes=0 freq=400015347 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13510 bytes_read=43626 bytes_retransmit=0 bytes_invalid=0 send_seq=2223 receive_seq=2223 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997238 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89537 bytes_read=2708723 bytes_retransmit=9 bytes_invalid=0 send_seq=11930 receive_seq=11930 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997687 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34561 bytes_read=374141 bytes_retransmit=9 bytes_invalid=0 send_seq=4161 receive_seq=4161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997436 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13723 bytes_read=535445 bytes_retransmit=9 bytes_invalid=0 send_seq=2233 receive_seq=2233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997596 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14263 bytes_read=42801 bytes_retransmit=9 bytes_invalid=0 send_seq=2224 receive_seq=2224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999437 Octopus_Pro_H723_V1.1: temp=30.5 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62835 bytes_read=969672 bytes_retransmit=0 bytes_invalid=0 send_seq=6321 receive_seq=6321 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998618 coil_temp=17.8 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=42.7 th1: temp=42.2 th2: temp=47.4 th3: temp=45.6 sysload=0.18 cputime=186.636 memavail=7400888 print_time=2135.896 buffer_time=2.172 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 49 Hz
Stats 2112.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17804137 bytes_read=2127445 bytes_retransmit=9 bytes_invalid=0 send_seq=307323 receive_seq=307323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015358 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13516 bytes_read=43655 bytes_retransmit=0 bytes_invalid=0 send_seq=2224 receive_seq=2224 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997250 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89543 bytes_read=2708851 bytes_retransmit=9 bytes_invalid=0 send_seq=11931 receive_seq=11931 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997677 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34637 bytes_read=377225 bytes_retransmit=9 bytes_invalid=0 send_seq=4172 receive_seq=4172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997445 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13729 bytes_read=535739 bytes_retransmit=9 bytes_invalid=0 send_seq=2234 receive_seq=2234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997602 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14269 bytes_read=42828 bytes_retransmit=9 bytes_invalid=0 send_seq=2225 receive_seq=2225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999438 Octopus_Pro_H723_V1.1: temp=30.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62841 bytes_read=970017 bytes_retransmit=0 bytes_invalid=0 send_seq=6322 receive_seq=6322 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998616 coil_temp=17.8 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=43.3 th1: temp=42.8 th2: temp=47.2 th3: temp=45.8 sysload=0.17 cputime=186.719 memavail=7400912 print_time=2136.816 buffer_time=2.093 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 50 Hz
Stats 2113.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17806266 bytes_read=2128044 bytes_retransmit=9 bytes_invalid=0 send_seq=307375 receive_seq=307375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015368 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13522 bytes_read=43671 bytes_retransmit=0 bytes_invalid=0 send_seq=2225 receive_seq=2225 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997251 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89549 bytes_read=2708951 bytes_retransmit=9 bytes_invalid=0 send_seq=11932 receive_seq=11932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997652 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34713 bytes_read=380282 bytes_retransmit=9 bytes_invalid=0 send_seq=4183 receive_seq=4183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000028 adj=63997435 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13735 bytes_read=535973 bytes_retransmit=9 bytes_invalid=0 send_seq=2235 receive_seq=2235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997607 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14275 bytes_read=42844 bytes_retransmit=9 bytes_invalid=0 send_seq=2226 receive_seq=2226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999434 Octopus_Pro_H723_V1.1: temp=30.6 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62847 bytes_read=970369 bytes_retransmit=0 bytes_invalid=0 send_seq=6323 receive_seq=6323 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998607 coil_temp=17.8 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=42.8 th1: temp=42.7 th2: temp=47.7 th3: temp=45.5 sysload=0.17 cputime=186.802 memavail=7400912 print_time=2137.715 buffer_time=1.991 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 51 Hz
Stats 2114.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17809361 bytes_read=2128692 bytes_retransmit=9 bytes_invalid=0 send_seq=307443 receive_seq=307443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=0 freq=400015378 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13528 bytes_read=43687 bytes_retransmit=0 bytes_invalid=0 send_seq=2226 receive_seq=2226 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997239 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89555 bytes_read=2709051 bytes_retransmit=9 bytes_invalid=0 send_seq=11933 receive_seq=11933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997629 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34789 bytes_read=383397 bytes_retransmit=9 bytes_invalid=0 send_seq=4194 receive_seq=4194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997424 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=13741 bytes_read=536207 bytes_retransmit=9 bytes_invalid=0 send_seq=2236 receive_seq=2236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997599 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14281 bytes_read=42860 bytes_retransmit=9 bytes_invalid=0 send_seq=2227 receive_seq=2227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999432 Octopus_Pro_H723_V1.1: temp=30.4 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62853 bytes_read=970725 bytes_retransmit=0 bytes_invalid=0 send_seq=6324 receive_seq=6324 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998610 coil_temp=17.8 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=42.9 th1: temp=42.7 th2: temp=47.2 th3: temp=45.7 sysload=0.17 cputime=186.904 memavail=7393896 print_time=2138.907 buffer_time=2.183 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 52 Hz
Stats 2115.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17812184 bytes_read=2129329 bytes_retransmit=9 bytes_invalid=0 send_seq=307506 receive_seq=307506 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015379 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13534 bytes_read=43703 bytes_retransmit=0 bytes_invalid=0 send_seq=2227 receive_seq=2227 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997236 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89561 bytes_read=2709193 bytes_retransmit=9 bytes_invalid=0 send_seq=11934 receive_seq=11934 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997631 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34865 bytes_read=386483 bytes_retransmit=9 bytes_invalid=0 send_seq=4205 receive_seq=4205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997495 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13747 bytes_read=536516 bytes_retransmit=9 bytes_invalid=0 send_seq=2237 receive_seq=2237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997606 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14287 bytes_read=42876 bytes_retransmit=9 bytes_invalid=0 send_seq=2228 receive_seq=2228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999435 Octopus_Pro_H723_V1.1: temp=30.4 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62859 bytes_read=971081 bytes_retransmit=0 bytes_invalid=0 send_seq=6325 receive_seq=6325 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998617 coil_temp=17.8 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=43.4 th1: temp=41.8 th2: temp=46.8 th3: temp=45.8 sysload=0.17 cputime=186.990 memavail=7399536 print_time=2139.823 buffer_time=2.097 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Testing frequency 53 Hz
Stats 2116.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17814428 bytes_read=2129933 bytes_retransmit=9 bytes_invalid=0 send_seq=307559 receive_seq=307559 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015394 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13540 bytes_read=43719 bytes_retransmit=0 bytes_invalid=0 send_seq=2228 receive_seq=2228 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997241 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89567 bytes_read=2709293 bytes_retransmit=9 bytes_invalid=0 send_seq=11935 receive_seq=11935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997633 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=34941 bytes_read=389558 bytes_retransmit=9 bytes_invalid=0 send_seq=4216 receive_seq=4216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997645 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13753 bytes_read=536750 bytes_retransmit=9 bytes_invalid=0 send_seq=2238 receive_seq=2238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997613 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14293 bytes_read=42892 bytes_retransmit=9 bytes_invalid=0 send_seq=2229 receive_seq=2229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999436 Octopus_Pro_H723_V1.1: temp=30.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62865 bytes_read=971437 bytes_retransmit=0 bytes_invalid=0 send_seq=6326 receive_seq=6326 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998648 coil_temp=17.8 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=43.2 th1: temp=42.6 th2: temp=47.6 th3: temp=45.6 sysload=0.17 cputime=187.074 memavail=7399480 print_time=2140.722 buffer_time=1.996 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 54 Hz
Stats 2117.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17817692 bytes_read=2130598 bytes_retransmit=9 bytes_invalid=0 send_seq=307630 receive_seq=307630 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015407 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13546 bytes_read=43748 bytes_retransmit=0 bytes_invalid=0 send_seq=2229 receive_seq=2229 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997237 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89573 bytes_read=2709393 bytes_retransmit=9 bytes_invalid=0 send_seq=11936 receive_seq=11936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997604 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35017 bytes_read=392614 bytes_retransmit=9 bytes_invalid=0 send_seq=4227 receive_seq=4227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997588 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13759 bytes_read=536984 bytes_retransmit=9 bytes_invalid=0 send_seq=2239 receive_seq=2239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997615 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14299 bytes_read=42919 bytes_retransmit=9 bytes_invalid=0 send_seq=2230 receive_seq=2230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999432 Octopus_Pro_H723_V1.1: temp=30.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62871 bytes_read=971793 bytes_retransmit=0 bytes_invalid=0 send_seq=6327 receive_seq=6327 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998633 coil_temp=17.8 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=42.8 th1: temp=42.6 th2: temp=47.4 th3: temp=45.7 sysload=0.16 cputime=187.166 memavail=7399480 print_time=2141.931 buffer_time=2.204 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 55 Hz
Stats 2118.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17820522 bytes_read=2131223 bytes_retransmit=9 bytes_invalid=0 send_seq=307693 receive_seq=307693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015412 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13552 bytes_read=43764 bytes_retransmit=0 bytes_invalid=0 send_seq=2230 receive_seq=2230 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997247 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89579 bytes_read=2709521 bytes_retransmit=9 bytes_invalid=0 send_seq=11937 receive_seq=11937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997612 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35093 bytes_read=395700 bytes_retransmit=9 bytes_invalid=0 send_seq=4238 receive_seq=4238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997546 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13765 bytes_read=537278 bytes_retransmit=9 bytes_invalid=0 send_seq=2240 receive_seq=2240 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997613 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14305 bytes_read=42935 bytes_retransmit=9 bytes_invalid=0 send_seq=2231 receive_seq=2231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999436 Octopus_Pro_H723_V1.1: temp=30.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62877 bytes_read=972149 bytes_retransmit=0 bytes_invalid=0 send_seq=6328 receive_seq=6328 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998644 coil_temp=17.8 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=42.9 th1: temp=42.9 th2: temp=47.3 th3: temp=45.7 sysload=0.16 cputime=187.249 memavail=7399484 print_time=2142.833 buffer_time=2.105 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2119.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17822860 bytes_read=2131832 bytes_retransmit=9 bytes_invalid=0 send_seq=307747 receive_seq=307747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015429 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13558 bytes_read=43780 bytes_retransmit=0 bytes_invalid=0 send_seq=2231 receive_seq=2231 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997257 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89585 bytes_read=2709621 bytes_retransmit=9 bytes_invalid=0 send_seq=11938 receive_seq=11938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997605 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35169 bytes_read=398757 bytes_retransmit=9 bytes_invalid=0 send_seq=4249 receive_seq=4249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13771 bytes_read=537512 bytes_retransmit=9 bytes_invalid=0 send_seq=2241 receive_seq=2241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997609 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14311 bytes_read=42951 bytes_retransmit=9 bytes_invalid=0 send_seq=2232 receive_seq=2232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999436 Octopus_Pro_H723_V1.1: temp=30.1 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62883 bytes_read=972505 bytes_retransmit=0 bytes_invalid=0 send_seq=6329 receive_seq=6329 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998641 coil_temp=17.8 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=43.2 th1: temp=42.6 th2: temp=47.3 th3: temp=45.7 sysload=0.16 cputime=187.333 memavail=7399488 print_time=2143.751 buffer_time=2.023 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 56 Hz
Testing frequency 57 Hz
Stats 2120.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17826154 bytes_read=2132508 bytes_retransmit=9 bytes_invalid=0 send_seq=307817 receive_seq=307817 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=0 freq=400015442 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13564 bytes_read=43796 bytes_retransmit=0 bytes_invalid=0 send_seq=2232 receive_seq=2232 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999214 adj=49997245 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89591 bytes_read=2709735 bytes_retransmit=9 bytes_invalid=0 send_seq=11939 receive_seq=11939 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997582 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35245 bytes_read=401814 bytes_retransmit=9 bytes_invalid=0 send_seq=4260 receive_seq=4260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997488 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13777 bytes_read=537761 bytes_retransmit=9 bytes_invalid=0 send_seq=2242 receive_seq=2242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14317 bytes_read=42967 bytes_retransmit=9 bytes_invalid=0 send_seq=2233 receive_seq=2233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999434 Octopus_Pro_H723_V1.1: temp=30.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62889 bytes_read=972861 bytes_retransmit=0 bytes_invalid=0 send_seq=6330 receive_seq=6330 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998656 coil_temp=17.8 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=43.5 th1: temp=42.7 th2: temp=47.6 th3: temp=45.8 sysload=0.16 cputime=187.428 memavail=7399488 print_time=2144.957 buffer_time=2.229 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 58 Hz
Stats 2121.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17829112 bytes_read=2133148 bytes_retransmit=9 bytes_invalid=0 send_seq=307883 receive_seq=307883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015437 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13570 bytes_read=43812 bytes_retransmit=0 bytes_invalid=0 send_seq=2233 receive_seq=2233 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999214 adj=49997250 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89597 bytes_read=2709863 bytes_retransmit=9 bytes_invalid=0 send_seq=11940 receive_seq=11940 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997597 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35321 bytes_read=404976 bytes_retransmit=9 bytes_invalid=0 send_seq=4271 receive_seq=4271 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997489 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13783 bytes_read=538055 bytes_retransmit=9 bytes_invalid=0 send_seq=2243 receive_seq=2243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14323 bytes_read=42983 bytes_retransmit=9 bytes_invalid=0 send_seq=2234 receive_seq=2234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999434 Octopus_Pro_H723_V1.1: temp=30.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62895 bytes_read=973217 bytes_retransmit=0 bytes_invalid=0 send_seq=6331 receive_seq=6331 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998642 coil_temp=17.8 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=43.2 th1: temp=42.6 th2: temp=47.6 th3: temp=45.9 sysload=0.16 cputime=187.510 memavail=7399488 print_time=2145.846 buffer_time=2.118 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 59 Hz
Stats 2122.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17831489 bytes_read=2133757 bytes_retransmit=9 bytes_invalid=0 send_seq=307937 receive_seq=307937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015449 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13576 bytes_read=43841 bytes_retransmit=0 bytes_invalid=0 send_seq=2234 receive_seq=2234 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999215 adj=49997263 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89603 bytes_read=2709963 bytes_retransmit=9 bytes_invalid=0 send_seq=11941 receive_seq=11941 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997613 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35397 bytes_read=408032 bytes_retransmit=9 bytes_invalid=0 send_seq=4282 receive_seq=4282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13789 bytes_read=538289 bytes_retransmit=9 bytes_invalid=0 send_seq=2244 receive_seq=2244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14329 bytes_read=43010 bytes_retransmit=9 bytes_invalid=0 send_seq=2235 receive_seq=2235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999438 Octopus_Pro_H723_V1.1: temp=30.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62901 bytes_read=973573 bytes_retransmit=0 bytes_invalid=0 send_seq=6332 receive_seq=6332 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998654 coil_temp=17.8 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=43.3 th1: temp=43.2 th2: temp=47.4 th3: temp=45.9 sysload=0.14 cputime=187.592 memavail=7399496 print_time=2146.768 buffer_time=2.040 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Testing frequency 60 Hz
Stats 2123.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17834913 bytes_read=2134427 bytes_retransmit=9 bytes_invalid=0 send_seq=308009 receive_seq=308009 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015461 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13582 bytes_read=43857 bytes_retransmit=0 bytes_invalid=0 send_seq=2235 receive_seq=2235 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997261 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89609 bytes_read=2710063 bytes_retransmit=9 bytes_invalid=0 send_seq=11942 receive_seq=11942 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997612 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35473 bytes_read=411088 bytes_retransmit=9 bytes_invalid=0 send_seq=4293 receive_seq=4293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13795 bytes_read=538523 bytes_retransmit=9 bytes_invalid=0 send_seq=2245 receive_seq=2245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14335 bytes_read=43026 bytes_retransmit=9 bytes_invalid=0 send_seq=2236 receive_seq=2236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999434 Octopus_Pro_H723_V1.1: temp=30.1 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62907 bytes_read=973929 bytes_retransmit=0 bytes_invalid=0 send_seq=6333 receive_seq=6333 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998651 coil_temp=17.8 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.3 th1: temp=42.8 th2: temp=47.8 th3: temp=45.7 sysload=0.14 cputime=187.682 memavail=7399504 print_time=2147.976 buffer_time=2.247 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Testing frequency 61 Hz
Stats 2124.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17837860 bytes_read=2135062 bytes_retransmit=9 bytes_invalid=0 send_seq=308074 receive_seq=308074 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015469 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13588 bytes_read=43873 bytes_retransmit=0 bytes_invalid=0 send_seq=2236 receive_seq=2236 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997260 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89615 bytes_read=2710185 bytes_retransmit=9 bytes_invalid=0 send_seq=11943 receive_seq=11943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997625 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35549 bytes_read=414162 bytes_retransmit=9 bytes_invalid=0 send_seq=4304 receive_seq=4304 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13801 bytes_read=538797 bytes_retransmit=9 bytes_invalid=0 send_seq=2246 receive_seq=2246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14341 bytes_read=43042 bytes_retransmit=9 bytes_invalid=0 send_seq=2237 receive_seq=2237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999438 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62913 bytes_read=974285 bytes_retransmit=0 bytes_invalid=0 send_seq=6334 receive_seq=6334 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998649 coil_temp=17.8 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.4 th1: temp=43.0 th2: temp=47.6 th3: temp=45.8 sysload=0.14 cputime=187.767 memavail=7399256 print_time=2148.866 buffer_time=2.137 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 62 Hz
Stats 2125.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17840299 bytes_read=2135695 bytes_retransmit=9 bytes_invalid=0 send_seq=308131 receive_seq=308131 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015472 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13594 bytes_read=43889 bytes_retransmit=0 bytes_invalid=0 send_seq=2237 receive_seq=2237 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997260 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=89621 bytes_read=2710292 bytes_retransmit=9 bytes_invalid=0 send_seq=11944 receive_seq=11944 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997662 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35625 bytes_read=417204 bytes_retransmit=9 bytes_invalid=0 send_seq=4315 receive_seq=4315 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997486 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13807 bytes_read=539027 bytes_retransmit=9 bytes_invalid=0 send_seq=2247 receive_seq=2247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14347 bytes_read=43058 bytes_retransmit=9 bytes_invalid=0 send_seq=2238 receive_seq=2238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999436 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62919 bytes_read=974641 bytes_retransmit=0 bytes_invalid=0 send_seq=6335 receive_seq=6335 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998663 coil_temp=17.8 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.7 th1: temp=42.7 th2: temp=47.7 th3: temp=46.0 sysload=0.14 cputime=187.852 memavail=7399272 print_time=2149.776 buffer_time=2.046 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 63 Hz
Stats 2126.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17843871 bytes_read=2136374 bytes_retransmit=9 bytes_invalid=0 send_seq=308205 receive_seq=308205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=0 freq=400015467 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13600 bytes_read=43905 bytes_retransmit=0 bytes_invalid=0 send_seq=2238 receive_seq=2238 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999218 adj=49997265 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=89627 bytes_read=2710385 bytes_retransmit=9 bytes_invalid=0 send_seq=11945 receive_seq=11945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997656 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35694 bytes_read=420239 bytes_retransmit=9 bytes_invalid=0 send_seq=4325 receive_seq=4325 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997475 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13813 bytes_read=539245 bytes_retransmit=9 bytes_invalid=0 send_seq=2248 receive_seq=2248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14353 bytes_read=43074 bytes_retransmit=9 bytes_invalid=0 send_seq=2239 receive_seq=2239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999437 Octopus_Pro_H723_V1.1: temp=30.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62925 bytes_read=974997 bytes_retransmit=0 bytes_invalid=0 send_seq=6336 receive_seq=6336 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998668 coil_temp=17.8 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.4 th1: temp=42.9 th2: temp=47.6 th3: temp=46.0 sysload=0.14 cputime=187.944 memavail=7398264 print_time=2150.993 buffer_time=2.263 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Testing frequency 64 Hz
Stats 2127.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17846827 bytes_read=2136989 bytes_retransmit=9 bytes_invalid=0 send_seq=308266 receive_seq=308266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015470 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13606 bytes_read=43934 bytes_retransmit=0 bytes_invalid=0 send_seq=2239 receive_seq=2239 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999219 adj=49997285 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=89633 bytes_read=2710504 bytes_retransmit=9 bytes_invalid=0 send_seq=11946 receive_seq=11946 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997691 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35770 bytes_read=423305 bytes_retransmit=9 bytes_invalid=0 send_seq=4336 receive_seq=4336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997507 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13819 bytes_read=539519 bytes_retransmit=9 bytes_invalid=0 send_seq=2249 receive_seq=2249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14359 bytes_read=43101 bytes_retransmit=9 bytes_invalid=0 send_seq=2240 receive_seq=2240 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999444 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62931 bytes_read=975353 bytes_retransmit=0 bytes_invalid=0 send_seq=6337 receive_seq=6337 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998669 coil_temp=17.8 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.4 th1: temp=43.0 th2: temp=47.6 th3: temp=45.9 sysload=0.13 cputime=188.028 memavail=7398264 print_time=2151.865 buffer_time=2.134 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 65 Hz
Stats 2128.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17849398 bytes_read=2137618 bytes_retransmit=9 bytes_invalid=0 send_seq=308324 receive_seq=308324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015485 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13612 bytes_read=43950 bytes_retransmit=0 bytes_invalid=0 send_seq=2240 receive_seq=2240 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999219 adj=49997291 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=89639 bytes_read=2710601 bytes_retransmit=9 bytes_invalid=0 send_seq=11947 receive_seq=11947 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997680 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35846 bytes_read=426356 bytes_retransmit=9 bytes_invalid=0 send_seq=4347 receive_seq=4347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997491 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13825 bytes_read=539737 bytes_retransmit=9 bytes_invalid=0 send_seq=2250 receive_seq=2250 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14365 bytes_read=43117 bytes_retransmit=9 bytes_invalid=0 send_seq=2241 receive_seq=2241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62937 bytes_read=975709 bytes_retransmit=0 bytes_invalid=0 send_seq=6338 receive_seq=6338 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998656 coil_temp=17.8 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.7 th1: temp=42.8 th2: temp=47.6 th3: temp=46.0 sysload=0.13 cputime=188.114 memavail=7398264 print_time=2152.794 buffer_time=2.063 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Testing frequency 66 Hz
Stats 2129.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17853053 bytes_read=2138298 bytes_retransmit=9 bytes_invalid=0 send_seq=308398 receive_seq=308398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015494 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13618 bytes_read=43966 bytes_retransmit=0 bytes_invalid=0 send_seq=2241 receive_seq=2241 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999220 adj=49997273 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=89645 bytes_read=2710701 bytes_retransmit=9 bytes_invalid=0 send_seq=11948 receive_seq=11948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997647 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35922 bytes_read=429471 bytes_retransmit=9 bytes_invalid=0 send_seq=4358 receive_seq=4358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997473 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13831 bytes_read=539963 bytes_retransmit=9 bytes_invalid=0 send_seq=2251 receive_seq=2251 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14371 bytes_read=43133 bytes_retransmit=9 bytes_invalid=0 send_seq=2242 receive_seq=2242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999445 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=26.8  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62943 bytes_read=976065 bytes_retransmit=0 bytes_invalid=0 send_seq=6339 receive_seq=6339 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998634 coil_temp=17.8 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=43.5 th1: temp=43.2 th2: temp=47.6 th3: temp=46.0 sysload=0.13 cputime=188.209 memavail=7398280 print_time=2153.999 buffer_time=2.267 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 67 Hz
Stats 2130.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17856056 bytes_read=2138959 bytes_retransmit=9 bytes_invalid=0 send_seq=308465 receive_seq=308465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015495 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13624 bytes_read=43982 bytes_retransmit=0 bytes_invalid=0 send_seq=2242 receive_seq=2242 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999222 adj=49997274 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=89651 bytes_read=2710843 bytes_retransmit=9 bytes_invalid=0 send_seq=11949 receive_seq=11949 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997648 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=35998 bytes_read=432557 bytes_retransmit=9 bytes_invalid=0 send_seq=4369 receive_seq=4369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997514 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13837 bytes_read=540272 bytes_retransmit=9 bytes_invalid=0 send_seq=2252 receive_seq=2252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14377 bytes_read=43149 bytes_retransmit=9 bytes_invalid=0 send_seq=2243 receive_seq=2243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999443 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62949 bytes_read=976421 bytes_retransmit=0 bytes_invalid=0 send_seq=6340 receive_seq=6340 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998640 coil_temp=17.8 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.7 th1: temp=43.2 th2: temp=47.7 th3: temp=46.0 sysload=0.13 cputime=188.296 memavail=7398280 print_time=2154.882 buffer_time=2.149 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 68 Hz
Stats 2131.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17858803 bytes_read=2139608 bytes_retransmit=9 bytes_invalid=0 send_seq=308527 receive_seq=308527 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015497 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13630 bytes_read=43998 bytes_retransmit=0 bytes_invalid=0 send_seq=2243 receive_seq=2243 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999223 adj=49997291 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=89657 bytes_read=2710943 bytes_retransmit=9 bytes_invalid=0 send_seq=11950 receive_seq=11950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997660 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36074 bytes_read=435630 bytes_retransmit=9 bytes_invalid=0 send_seq=4380 receive_seq=4380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997501 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13843 bytes_read=540506 bytes_retransmit=9 bytes_invalid=0 send_seq=2253 receive_seq=2253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14383 bytes_read=43165 bytes_retransmit=9 bytes_invalid=0 send_seq=2244 receive_seq=2244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999442 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62955 bytes_read=976777 bytes_retransmit=0 bytes_invalid=0 send_seq=6341 receive_seq=6341 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998642 coil_temp=17.8 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.7 th1: temp=43.1 th2: temp=47.6 th3: temp=46.1 sysload=0.13 cputime=188.388 memavail=7391988 print_time=2155.808 buffer_time=2.074 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 69 Hz
Stats 2132.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17862506 bytes_read=2140303 bytes_retransmit=9 bytes_invalid=0 send_seq=308604 receive_seq=308604 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015517 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13636 bytes_read=44027 bytes_retransmit=0 bytes_invalid=0 send_seq=2244 receive_seq=2244 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999224 adj=49997302 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=89663 bytes_read=2711043 bytes_retransmit=9 bytes_invalid=0 send_seq=11951 receive_seq=11951 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997659 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36150 bytes_read=438686 bytes_retransmit=9 bytes_invalid=0 send_seq=4391 receive_seq=4391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13849 bytes_read=540740 bytes_retransmit=9 bytes_invalid=0 send_seq=2254 receive_seq=2254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14389 bytes_read=43192 bytes_retransmit=9 bytes_invalid=0 send_seq=2245 receive_seq=2245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999442 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62961 bytes_read=977133 bytes_retransmit=0 bytes_invalid=0 send_seq=6342 receive_seq=6342 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998638 coil_temp=17.8 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.8 th1: temp=43.1 th2: temp=47.8 th3: temp=46.1 sysload=0.12 cputime=188.484 memavail=7398128 print_time=2157.016 buffer_time=2.282 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 70 Hz
Stats 2133.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17865518 bytes_read=2140943 bytes_retransmit=9 bytes_invalid=0 send_seq=308670 receive_seq=308670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=23 upcoming_bytes=0 freq=400015520 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13642 bytes_read=44043 bytes_retransmit=0 bytes_invalid=0 send_seq=2245 receive_seq=2245 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999225 adj=49997283 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=89669 bytes_read=2711171 bytes_retransmit=9 bytes_invalid=0 send_seq=11952 receive_seq=11952 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997654 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36226 bytes_read=441773 bytes_retransmit=9 bytes_invalid=0 send_seq=4402 receive_seq=4402 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997470 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13855 bytes_read=541034 bytes_retransmit=9 bytes_invalid=0 send_seq=2255 receive_seq=2255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997623 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14395 bytes_read=43208 bytes_retransmit=9 bytes_invalid=0 send_seq=2246 receive_seq=2246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62967 bytes_read=977489 bytes_retransmit=0 bytes_invalid=0 send_seq=6343 receive_seq=6343 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998628 coil_temp=17.8 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.7 th1: temp=43.3 th2: temp=47.8 th3: temp=46.1 sysload=0.12 cputime=188.573 memavail=7398140 print_time=2157.888 buffer_time=2.154 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 71 Hz
Stats 2134.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17868368 bytes_read=2141597 bytes_retransmit=9 bytes_invalid=0 send_seq=308733 receive_seq=308733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015523 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13648 bytes_read=44059 bytes_retransmit=0 bytes_invalid=0 send_seq=2246 receive_seq=2246 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999226 adj=49997293 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=89675 bytes_read=2711271 bytes_retransmit=9 bytes_invalid=0 send_seq=11953 receive_seq=11953 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997652 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36302 bytes_read=444832 bytes_retransmit=9 bytes_invalid=0 send_seq=4413 receive_seq=4413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997609 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13861 bytes_read=541268 bytes_retransmit=9 bytes_invalid=0 send_seq=2256 receive_seq=2256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14401 bytes_read=43224 bytes_retransmit=9 bytes_invalid=0 send_seq=2247 receive_seq=2247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999436 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62973 bytes_read=977845 bytes_retransmit=0 bytes_invalid=0 send_seq=6344 receive_seq=6344 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998628 coil_temp=17.8 refs=0 mcu_temp=20.76 supply_voltage=3.012 th0: temp=43.4 th1: temp=43.1 th2: temp=47.7 th3: temp=46.0 sysload=0.12 cputime=188.665 memavail=7398140 print_time=2158.819 buffer_time=2.085 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 72 Hz
Stats 2135.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17872219 bytes_read=2142318 bytes_retransmit=9 bytes_invalid=0 send_seq=308812 receive_seq=308812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=0 freq=400015516 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13654 bytes_read=44075 bytes_retransmit=0 bytes_invalid=0 send_seq=2247 receive_seq=2247 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999227 adj=49997296 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89681 bytes_read=2711385 bytes_retransmit=9 bytes_invalid=0 send_seq=11954 receive_seq=11954 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997645 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36378 bytes_read=447890 bytes_retransmit=9 bytes_invalid=0 send_seq=4424 receive_seq=4424 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997575 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13867 bytes_read=541517 bytes_retransmit=9 bytes_invalid=0 send_seq=2257 receive_seq=2257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997617 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14407 bytes_read=43240 bytes_retransmit=9 bytes_invalid=0 send_seq=2248 receive_seq=2248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999437 Octopus_Pro_H723_V1.1: temp=30.1 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62979 bytes_read=978201 bytes_retransmit=0 bytes_invalid=0 send_seq=6345 receive_seq=6345 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998651 coil_temp=17.8 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=43.7 th1: temp=43.4 th2: temp=47.9 th3: temp=46.0 sysload=0.12 cputime=188.761 memavail=7398144 print_time=2160.033 buffer_time=2.298 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 73 Hz
Stats 2136.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17875313 bytes_read=2142959 bytes_retransmit=9 bytes_invalid=0 send_seq=308879 receive_seq=308879 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015529 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13660 bytes_read=44091 bytes_retransmit=0 bytes_invalid=0 send_seq=2248 receive_seq=2248 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999228 adj=49997313 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89687 bytes_read=2711513 bytes_retransmit=9 bytes_invalid=0 send_seq=11955 receive_seq=11955 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997672 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36454 bytes_read=451050 bytes_retransmit=9 bytes_invalid=0 send_seq=4435 receive_seq=4435 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997568 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13873 bytes_read=541811 bytes_retransmit=9 bytes_invalid=0 send_seq=2258 receive_seq=2258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14413 bytes_read=43256 bytes_retransmit=9 bytes_invalid=0 send_seq=2249 receive_seq=2249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999443 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62985 bytes_read=978557 bytes_retransmit=0 bytes_invalid=0 send_seq=6346 receive_seq=6346 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998662 coil_temp=17.8 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.5 th1: temp=43.1 th2: temp=47.8 th3: temp=46.2 sysload=0.12 cputime=188.849 memavail=7397140 print_time=2160.906 buffer_time=2.170 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 74 Hz
Stats 2137.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17878372 bytes_read=2143633 bytes_retransmit=9 bytes_invalid=0 send_seq=308946 receive_seq=308946 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015527 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13666 bytes_read=44120 bytes_retransmit=0 bytes_invalid=0 send_seq=2249 receive_seq=2249 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999229 adj=49997306 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89693 bytes_read=2711613 bytes_retransmit=9 bytes_invalid=0 send_seq=11956 receive_seq=11956 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997644 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36530 bytes_read=454107 bytes_retransmit=9 bytes_invalid=0 send_seq=4446 receive_seq=4446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997589 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13879 bytes_read=542045 bytes_retransmit=9 bytes_invalid=0 send_seq=2259 receive_seq=2259 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14419 bytes_read=43283 bytes_retransmit=9 bytes_invalid=0 send_seq=2250 receive_seq=2250 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999439 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62991 bytes_read=978913 bytes_retransmit=0 bytes_invalid=0 send_seq=6347 receive_seq=6347 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998645 coil_temp=17.8 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.6 th1: temp=43.4 th2: temp=47.9 th3: temp=46.3 sysload=0.11 cputime=188.938 memavail=7397144 print_time=2161.843 buffer_time=2.108 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 75 Hz
Stats 2138.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17882156 bytes_read=2144278 bytes_retransmit=9 bytes_invalid=0 send_seq=309025 receive_seq=309013 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=83 upcoming_bytes=0 freq=400015520 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13672 bytes_read=44136 bytes_retransmit=0 bytes_invalid=0 send_seq=2250 receive_seq=2250 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999229 adj=49997316 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89699 bytes_read=2711713 bytes_retransmit=9 bytes_invalid=0 send_seq=11957 receive_seq=11957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997650 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36606 bytes_read=457164 bytes_retransmit=9 bytes_invalid=0 send_seq=4457 receive_seq=4457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997573 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13885 bytes_read=542294 bytes_retransmit=9 bytes_invalid=0 send_seq=2260 receive_seq=2260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14425 bytes_read=43299 bytes_retransmit=9 bytes_invalid=0 send_seq=2251 receive_seq=2251 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=62997 bytes_read=979269 bytes_retransmit=0 bytes_invalid=0 send_seq=6348 receive_seq=6348 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998652 coil_temp=17.8 refs=0 mcu_temp=20.76 supply_voltage=3.012 th0: temp=43.7 th1: temp=43.6 th2: temp=48.1 th3: temp=46.2 sysload=0.11 cputime=189.034 memavail=7397144 print_time=2163.038 buffer_time=2.298 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 76 Hz
Stats 2139.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17885280 bytes_read=2145004 bytes_retransmit=9 bytes_invalid=0 send_seq=309094 receive_seq=309094 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015567 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13684 bytes_read=44168 bytes_retransmit=0 bytes_invalid=0 send_seq=2252 receive_seq=2252 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999231 adj=49997324 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89711 bytes_read=2711857 bytes_retransmit=9 bytes_invalid=0 send_seq=11959 receive_seq=11959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997676 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36688 bytes_read=460265 bytes_retransmit=9 bytes_invalid=0 send_seq=4469 receive_seq=4469 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997565 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13897 bytes_read=542589 bytes_retransmit=9 bytes_invalid=0 send_seq=2262 receive_seq=2262 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999532 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14437 bytes_read=43331 bytes_retransmit=9 bytes_invalid=0 send_seq=2253 receive_seq=2253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63009 bytes_read=979641 bytes_retransmit=0 bytes_invalid=0 send_seq=6350 receive_seq=6350 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998662 coil_temp=17.8 refs=0 mcu_temp=20.75 supply_voltage=3.012 th0: temp=43.9 th1: temp=43.2 th2: temp=47.8 th3: temp=46.2 sysload=0.11 cputime=189.124 memavail=7397144 print_time=2163.913 buffer_time=2.173 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 77 Hz
Stats 2140.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17888374 bytes_read=2145699 bytes_retransmit=9 bytes_invalid=0 send_seq=309162 receive_seq=309162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015560 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13690 bytes_read=44184 bytes_retransmit=0 bytes_invalid=0 send_seq=2253 receive_seq=2253 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999231 adj=49997268 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89717 bytes_read=2711971 bytes_retransmit=9 bytes_invalid=0 send_seq=11960 receive_seq=11960 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997725 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36764 bytes_read=463321 bytes_retransmit=9 bytes_invalid=0 send_seq=4480 receive_seq=4480 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997435 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13903 bytes_read=542838 bytes_retransmit=9 bytes_invalid=0 send_seq=2263 receive_seq=2263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999531 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14443 bytes_read=43347 bytes_retransmit=9 bytes_invalid=0 send_seq=2254 receive_seq=2254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999429 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63015 bytes_read=979997 bytes_retransmit=0 bytes_invalid=0 send_seq=6351 receive_seq=6351 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998734 coil_temp=17.8 refs=0 mcu_temp=20.76 supply_voltage=3.012 th0: temp=43.8 th1: temp=43.8 th2: temp=48.0 th3: temp=46.3 sysload=0.11 cputime=189.215 memavail=7397144 print_time=2164.847 buffer_time=2.106 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 78 Hz
Stats 2141.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17892430 bytes_read=2146424 bytes_retransmit=9 bytes_invalid=0 send_seq=309245 receive_seq=309245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=0 freq=400015576 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13696 bytes_read=44200 bytes_retransmit=0 bytes_invalid=0 send_seq=2254 receive_seq=2254 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999232 adj=49997287 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89723 bytes_read=2712071 bytes_retransmit=9 bytes_invalid=0 send_seq=11961 receive_seq=11961 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997722 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36840 bytes_read=466395 bytes_retransmit=9 bytes_invalid=0 send_seq=4491 receive_seq=4491 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997453 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13909 bytes_read=543087 bytes_retransmit=9 bytes_invalid=0 send_seq=2264 receive_seq=2264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999531 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14449 bytes_read=43363 bytes_retransmit=9 bytes_invalid=0 send_seq=2255 receive_seq=2255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999433 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63021 bytes_read=980353 bytes_retransmit=0 bytes_invalid=0 send_seq=6352 receive_seq=6352 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998739 coil_temp=17.8 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=43.9 th1: temp=43.2 th2: temp=47.6 th3: temp=46.1 sysload=0.11 cputime=189.314 memavail=7397144 print_time=2166.053 buffer_time=2.312 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 79 Hz
Stats 2142.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17895450 bytes_read=2147059 bytes_retransmit=9 bytes_invalid=0 send_seq=309310 receive_seq=309310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015591 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13702 bytes_read=44229 bytes_retransmit=0 bytes_invalid=0 send_seq=2255 receive_seq=2255 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999233 adj=49997271 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89729 bytes_read=2712199 bytes_retransmit=9 bytes_invalid=0 send_seq=11962 receive_seq=11962 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997691 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36916 bytes_read=469481 bytes_retransmit=9 bytes_invalid=0 send_seq=4502 receive_seq=4502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997438 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13915 bytes_read=543366 bytes_retransmit=9 bytes_invalid=0 send_seq=2265 receive_seq=2265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14455 bytes_read=43390 bytes_retransmit=9 bytes_invalid=0 send_seq=2256 receive_seq=2256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999432 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63027 bytes_read=980709 bytes_retransmit=0 bytes_invalid=0 send_seq=6353 receive_seq=6353 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998693 coil_temp=17.8 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.9 th1: temp=43.3 th2: temp=47.9 th3: temp=46.1 sysload=0.10 cputime=189.403 memavail=7397144 print_time=2166.923 buffer_time=2.182 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 80 Hz
Stats 2143.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17898693 bytes_read=2147748 bytes_retransmit=9 bytes_invalid=0 send_seq=309380 receive_seq=309380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015584 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13708 bytes_read=44245 bytes_retransmit=0 bytes_invalid=0 send_seq=2256 receive_seq=2256 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997261 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89735 bytes_read=2712299 bytes_retransmit=9 bytes_invalid=0 send_seq=11963 receive_seq=11963 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997652 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=36985 bytes_read=472573 bytes_retransmit=9 bytes_invalid=0 send_seq=4512 receive_seq=4512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997409 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13921 bytes_read=543600 bytes_retransmit=9 bytes_invalid=0 send_seq=2266 receive_seq=2266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999531 adj=47997607 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14461 bytes_read=43406 bytes_retransmit=9 bytes_invalid=0 send_seq=2257 receive_seq=2257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999430 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63033 bytes_read=981065 bytes_retransmit=0 bytes_invalid=0 send_seq=6354 receive_seq=6354 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998663 coil_temp=17.8 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.0 th1: temp=43.4 th2: temp=48.0 th3: temp=46.3 sysload=0.10 cputime=189.493 memavail=7397144 print_time=2167.859 buffer_time=2.116 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 81 Hz
Stats 2144.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17901698 bytes_read=2148378 bytes_retransmit=9 bytes_invalid=0 send_seq=309444 receive_seq=309444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015604 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13714 bytes_read=44261 bytes_retransmit=0 bytes_invalid=0 send_seq=2257 receive_seq=2257 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997295 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89741 bytes_read=2712413 bytes_retransmit=9 bytes_invalid=0 send_seq=11964 receive_seq=11964 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997670 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37061 bytes_read=475631 bytes_retransmit=9 bytes_invalid=0 send_seq=4523 receive_seq=4523 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997440 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13927 bytes_read=543849 bytes_retransmit=9 bytes_invalid=0 send_seq=2267 receive_seq=2267 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999531 adj=47997632 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14467 bytes_read=43422 bytes_retransmit=9 bytes_invalid=0 send_seq=2258 receive_seq=2258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999436 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63039 bytes_read=981421 bytes_retransmit=0 bytes_invalid=0 send_seq=6355 receive_seq=6355 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998671 coil_temp=17.7 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=44.0 th1: temp=42.9 th2: temp=48.2 th3: temp=46.4 sysload=0.10 cputime=189.581 memavail=7397144 print_time=2168.734 buffer_time=1.991 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 82 Hz
Stats 2145.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17905707 bytes_read=2149094 bytes_retransmit=9 bytes_invalid=0 send_seq=309522 receive_seq=309522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015652 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13720 bytes_read=44277 bytes_retransmit=0 bytes_invalid=0 send_seq=2258 receive_seq=2258 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997262 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89747 bytes_read=2712541 bytes_retransmit=9 bytes_invalid=0 send_seq=11965 receive_seq=11965 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997622 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37137 bytes_read=478716 bytes_retransmit=9 bytes_invalid=0 send_seq=4534 receive_seq=4534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997423 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13933 bytes_read=544143 bytes_retransmit=9 bytes_invalid=0 send_seq=2268 receive_seq=2268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997602 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14473 bytes_read=43438 bytes_retransmit=9 bytes_invalid=0 send_seq=2259 receive_seq=2259 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999436 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63045 bytes_read=981777 bytes_retransmit=0 bytes_invalid=0 send_seq=6356 receive_seq=6356 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998634 coil_temp=17.7 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=43.9 th1: temp=43.3 th2: temp=48.1 th3: temp=46.3 sysload=0.10 cputime=189.680 memavail=7397144 print_time=2169.935 buffer_time=2.192 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 83 Hz
Stats 2146.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17909131 bytes_read=2149796 bytes_retransmit=9 bytes_invalid=0 send_seq=309595 receive_seq=309595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015638 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13726 bytes_read=44293 bytes_retransmit=0 bytes_invalid=0 send_seq=2259 receive_seq=2259 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997209 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89753 bytes_read=2712641 bytes_retransmit=9 bytes_invalid=0 send_seq=11966 receive_seq=11966 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997546 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37213 bytes_read=481790 bytes_retransmit=9 bytes_invalid=0 send_seq=4545 receive_seq=4545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997355 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13939 bytes_read=544377 bytes_retransmit=9 bytes_invalid=0 send_seq=2269 receive_seq=2269 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997545 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14479 bytes_read=43454 bytes_retransmit=9 bytes_invalid=0 send_seq=2260 receive_seq=2260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999422 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63051 bytes_read=982133 bytes_retransmit=0 bytes_invalid=0 send_seq=6357 receive_seq=6357 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998593 coil_temp=17.7 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.1 th1: temp=43.7 th2: temp=48.0 th3: temp=46.3 sysload=0.10 cputime=189.773 memavail=7396908 print_time=2170.879 buffer_time=2.135 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 84 Hz
Stats 2147.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17913185 bytes_read=2150484 bytes_retransmit=9 bytes_invalid=0 send_seq=309679 receive_seq=309671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=0 freq=400015641 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13732 bytes_read=44322 bytes_retransmit=0 bytes_invalid=0 send_seq=2260 receive_seq=2260 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997250 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89759 bytes_read=2712755 bytes_retransmit=9 bytes_invalid=0 send_seq=11967 receive_seq=11967 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997596 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37289 bytes_read=484860 bytes_retransmit=9 bytes_invalid=0 send_seq=4556 receive_seq=4556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997494 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13945 bytes_read=544641 bytes_retransmit=9 bytes_invalid=0 send_seq=2270 receive_seq=2270 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997574 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14485 bytes_read=43481 bytes_retransmit=9 bytes_invalid=0 send_seq=2261 receive_seq=2261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999430 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63057 bytes_read=982489 bytes_retransmit=0 bytes_invalid=0 send_seq=6358 receive_seq=6358 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998618 coil_temp=17.7 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.1 th1: temp=43.4 th2: temp=48.0 th3: temp=46.3 sysload=0.09 cputime=189.874 memavail=7396932 print_time=2172.071 buffer_time=2.319 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 85 Hz
Stats 2148.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17916259 bytes_read=2151188 bytes_retransmit=9 bytes_invalid=0 send_seq=309747 receive_seq=309747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015628 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13738 bytes_read=44338 bytes_retransmit=0 bytes_invalid=0 send_seq=2261 receive_seq=2261 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997267 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89765 bytes_read=2712869 bytes_retransmit=9 bytes_invalid=0 send_seq=11968 receive_seq=11968 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997610 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37365 bytes_read=487988 bytes_retransmit=9 bytes_invalid=0 send_seq=4567 receive_seq=4567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997486 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13951 bytes_read=544905 bytes_retransmit=9 bytes_invalid=0 send_seq=2271 receive_seq=2271 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997588 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14491 bytes_read=43497 bytes_retransmit=9 bytes_invalid=0 send_seq=2262 receive_seq=2262 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63063 bytes_read=982845 bytes_retransmit=0 bytes_invalid=0 send_seq=6359 receive_seq=6359 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998628 coil_temp=17.7 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.9 th1: temp=43.4 th2: temp=48.1 th3: temp=46.3 sysload=0.09 cputime=189.964 memavail=7396932 print_time=2172.944 buffer_time=2.192 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Testing frequency 86 Hz
Stats 2149.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17919735 bytes_read=2151883 bytes_retransmit=9 bytes_invalid=0 send_seq=309821 receive_seq=309821 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015638 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13744 bytes_read=44354 bytes_retransmit=0 bytes_invalid=0 send_seq=2262 receive_seq=2262 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997300 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89771 bytes_read=2712969 bytes_retransmit=9 bytes_invalid=0 send_seq=11969 receive_seq=11969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997753 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37441 bytes_read=491044 bytes_retransmit=9 bytes_invalid=0 send_seq=4578 receive_seq=4578 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997514 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=13957 bytes_read=545139 bytes_retransmit=9 bytes_invalid=0 send_seq=2272 receive_seq=2272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997607 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14497 bytes_read=43513 bytes_retransmit=9 bytes_invalid=0 send_seq=2263 receive_seq=2263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999447 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63069 bytes_read=983201 bytes_retransmit=0 bytes_invalid=0 send_seq=6360 receive_seq=6360 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998635 coil_temp=17.7 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.0 th1: temp=43.2 th2: temp=48.1 th3: temp=46.5 sysload=0.09 cputime=190.065 memavail=7397288 print_time=2173.881 buffer_time=2.128 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 87 Hz
Stats 2150.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17923727 bytes_read=2152539 bytes_retransmit=9 bytes_invalid=0 send_seq=309899 receive_seq=309887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=185 upcoming_bytes=0 freq=400015648 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13750 bytes_read=44370 bytes_retransmit=0 bytes_invalid=0 send_seq=2263 receive_seq=2263 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997287 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89777 bytes_read=2713097 bytes_retransmit=9 bytes_invalid=0 send_seq=11970 receive_seq=11970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997707 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37517 bytes_read=494114 bytes_retransmit=9 bytes_invalid=0 send_seq=4589 receive_seq=4589 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997482 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13963 bytes_read=545418 bytes_retransmit=9 bytes_invalid=0 send_seq=2273 receive_seq=2273 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997593 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14503 bytes_read=43529 bytes_retransmit=9 bytes_invalid=0 send_seq=2264 receive_seq=2264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63075 bytes_read=983557 bytes_retransmit=0 bytes_invalid=0 send_seq=6361 receive_seq=6361 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998619 coil_temp=17.7 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.7 th1: temp=43.4 th2: temp=48.1 th3: temp=46.4 sysload=0.09 cputime=190.168 memavail=7397288 print_time=2175.080 buffer_time=2.324 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 88 Hz
Stats 2151.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17926880 bytes_read=2153273 bytes_retransmit=9 bytes_invalid=0 send_seq=309969 receive_seq=309969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=0 freq=400015640 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13756 bytes_read=44386 bytes_retransmit=0 bytes_invalid=0 send_seq=2264 receive_seq=2264 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997275 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89783 bytes_read=2713211 bytes_retransmit=9 bytes_invalid=0 send_seq=11971 receive_seq=11971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997676 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37593 bytes_read=497204 bytes_retransmit=9 bytes_invalid=0 send_seq=4600 receive_seq=4600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997471 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13969 bytes_read=545682 bytes_retransmit=9 bytes_invalid=0 send_seq=2274 receive_seq=2274 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997605 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14509 bytes_read=43545 bytes_retransmit=9 bytes_invalid=0 send_seq=2265 receive_seq=2265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63081 bytes_read=983913 bytes_retransmit=0 bytes_invalid=0 send_seq=6362 receive_seq=6362 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998615 coil_temp=17.7 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.1 th1: temp=43.4 th2: temp=48.1 th3: temp=46.4 sysload=0.09 cputime=190.262 memavail=7397288 print_time=2175.949 buffer_time=2.192 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 89 Hz
Stats 2152.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17930427 bytes_read=2153973 bytes_retransmit=9 bytes_invalid=0 send_seq=310044 receive_seq=310044 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015635 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=13762 bytes_read=44415 bytes_retransmit=0 bytes_invalid=0 send_seq=2265 receive_seq=2265 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997313 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89789 bytes_read=2713311 bytes_retransmit=9 bytes_invalid=0 send_seq=11972 receive_seq=11972 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997683 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37669 bytes_read=500265 bytes_retransmit=9 bytes_invalid=0 send_seq=4611 receive_seq=4611 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997615 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13975 bytes_read=545916 bytes_retransmit=9 bytes_invalid=0 send_seq=2275 receive_seq=2275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14515 bytes_read=43572 bytes_retransmit=9 bytes_invalid=0 send_seq=2266 receive_seq=2266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63087 bytes_read=984269 bytes_retransmit=0 bytes_invalid=0 send_seq=6363 receive_seq=6363 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998624 coil_temp=17.7 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=44.5 th1: temp=43.9 th2: temp=48.1 th3: temp=46.5 sysload=0.09 cputime=190.359 memavail=7397288 print_time=2176.882 buffer_time=2.125 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 90 Hz
Stats 2153.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17933463 bytes_read=2154618 bytes_retransmit=9 bytes_invalid=0 send_seq=310111 receive_seq=310111 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015635 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=13768 bytes_read=44431 bytes_retransmit=0 bytes_invalid=0 send_seq=2266 receive_seq=2266 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997320 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89795 bytes_read=2713425 bytes_retransmit=9 bytes_invalid=0 send_seq=11973 receive_seq=11973 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997753 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37745 bytes_read=503335 bytes_retransmit=9 bytes_invalid=0 send_seq=4622 receive_seq=4622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997587 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13981 bytes_read=546180 bytes_retransmit=9 bytes_invalid=0 send_seq=2276 receive_seq=2276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997649 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14521 bytes_read=43588 bytes_retransmit=9 bytes_invalid=0 send_seq=2267 receive_seq=2267 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999449 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63093 bytes_read=984625 bytes_retransmit=0 bytes_invalid=0 send_seq=6364 receive_seq=6364 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998645 coil_temp=17.7 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=44.3 th1: temp=43.6 th2: temp=48.3 th3: temp=46.3 sysload=0.09 cputime=190.452 memavail=7397292 print_time=2177.761 buffer_time=2.004 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 91 Hz
Stats 2154.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17937688 bytes_read=2155392 bytes_retransmit=9 bytes_invalid=0 send_seq=310198 receive_seq=310198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=0 freq=400015628 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=13774 bytes_read=44447 bytes_retransmit=0 bytes_invalid=0 send_seq=2267 receive_seq=2267 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997327 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89801 bytes_read=2713539 bytes_retransmit=9 bytes_invalid=0 send_seq=11974 receive_seq=11974 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997748 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37821 bytes_read=506464 bytes_retransmit=9 bytes_invalid=0 send_seq=4633 receive_seq=4633 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997582 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13987 bytes_read=546444 bytes_retransmit=9 bytes_invalid=0 send_seq=2277 receive_seq=2277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14527 bytes_read=43604 bytes_retransmit=9 bytes_invalid=0 send_seq=2268 receive_seq=2268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999449 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63099 bytes_read=984981 bytes_retransmit=0 bytes_invalid=0 send_seq=6365 receive_seq=6365 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998672 coil_temp=17.7 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=44.2 th1: temp=43.3 th2: temp=48.0 th3: temp=46.4 sysload=0.09 cputime=190.556 memavail=7397292 print_time=2178.964 buffer_time=2.206 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Testing frequency 92 Hz
Stats 2155.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17941421 bytes_read=2156108 bytes_retransmit=9 bytes_invalid=0 send_seq=310276 receive_seq=310276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015622 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=13780 bytes_read=44463 bytes_retransmit=0 bytes_invalid=0 send_seq=2268 receive_seq=2268 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997328 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89807 bytes_read=2713653 bytes_retransmit=9 bytes_invalid=0 send_seq=11975 receive_seq=11975 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997738 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37897 bytes_read=509521 bytes_retransmit=9 bytes_invalid=0 send_seq=4644 receive_seq=4644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997568 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13993 bytes_read=546693 bytes_retransmit=9 bytes_invalid=0 send_seq=2278 receive_seq=2278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999531 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14533 bytes_read=43620 bytes_retransmit=9 bytes_invalid=0 send_seq=2269 receive_seq=2269 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63105 bytes_read=985337 bytes_retransmit=0 bytes_invalid=0 send_seq=6366 receive_seq=6366 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998683 coil_temp=17.7 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.8 th1: temp=43.2 th2: temp=48.2 th3: temp=46.5 sysload=0.09 cputime=190.650 memavail=7397292 print_time=2179.899 buffer_time=2.141 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 93 Hz
Stats 2156.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17944411 bytes_read=2156748 bytes_retransmit=9 bytes_invalid=0 send_seq=310342 receive_seq=310342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015614 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=13786 bytes_read=44478 bytes_retransmit=0 bytes_invalid=0 send_seq=2269 receive_seq=2269 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997351 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89813 bytes_read=2713767 bytes_retransmit=9 bytes_invalid=0 send_seq=11976 receive_seq=11976 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997730 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=37973 bytes_read=512610 bytes_retransmit=9 bytes_invalid=0 send_seq=4655 receive_seq=4655 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997572 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=13999 bytes_read=546957 bytes_retransmit=9 bytes_invalid=0 send_seq=2279 receive_seq=2279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999531 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14539 bytes_read=43636 bytes_retransmit=9 bytes_invalid=0 send_seq=2270 receive_seq=2270 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63111 bytes_read=985693 bytes_retransmit=0 bytes_invalid=0 send_seq=6367 receive_seq=6367 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998682 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.6 th1: temp=43.5 th2: temp=48.2 th3: temp=46.5 sysload=0.09 cputime=190.744 memavail=7397300 print_time=2180.769 buffer_time=2.010 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 94 Hz
Stats 2157.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17948781 bytes_read=2157528 bytes_retransmit=9 bytes_invalid=0 send_seq=310431 receive_seq=310431 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015610 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13792 bytes_read=44506 bytes_retransmit=0 bytes_invalid=0 send_seq=2270 receive_seq=2270 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997362 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89819 bytes_read=2713881 bytes_retransmit=9 bytes_invalid=0 send_seq=11977 receive_seq=11977 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997728 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38049 bytes_read=515681 bytes_retransmit=9 bytes_invalid=0 send_seq=4666 receive_seq=4666 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997566 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14005 bytes_read=547221 bytes_retransmit=9 bytes_invalid=0 send_seq=2280 receive_seq=2280 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997683 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14545 bytes_read=43663 bytes_retransmit=9 bytes_invalid=0 send_seq=2271 receive_seq=2271 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999454 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63117 bytes_read=986049 bytes_retransmit=0 bytes_invalid=0 send_seq=6368 receive_seq=6368 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998675 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.7 th1: temp=43.3 th2: temp=48.1 th3: temp=46.5 sysload=0.08 cputime=190.849 memavail=7397300 print_time=2181.968 buffer_time=2.208 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 95 Hz
Stats 2158.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17952510 bytes_read=2158223 bytes_retransmit=9 bytes_invalid=0 send_seq=310508 receive_seq=310508 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015607 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13798 bytes_read=44521 bytes_retransmit=0 bytes_invalid=0 send_seq=2271 receive_seq=2271 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997360 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89825 bytes_read=2713981 bytes_retransmit=9 bytes_invalid=0 send_seq=11978 receive_seq=11978 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997728 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38125 bytes_read=518739 bytes_retransmit=9 bytes_invalid=0 send_seq=4677 receive_seq=4677 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14011 bytes_read=547455 bytes_retransmit=9 bytes_invalid=0 send_seq=2281 receive_seq=2281 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14551 bytes_read=43679 bytes_retransmit=9 bytes_invalid=0 send_seq=2272 receive_seq=2272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999455 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63123 bytes_read=986405 bytes_retransmit=0 bytes_invalid=0 send_seq=6369 receive_seq=6369 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998673 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.0 th1: temp=43.4 th2: temp=48.1 th3: temp=46.5 sysload=0.08 cputime=190.944 memavail=7397300 print_time=2182.905 buffer_time=2.146 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 96 Hz
Stats 2159.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17955507 bytes_read=2158863 bytes_retransmit=9 bytes_invalid=0 send_seq=310574 receive_seq=310574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015597 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13804 bytes_read=44536 bytes_retransmit=0 bytes_invalid=0 send_seq=2272 receive_seq=2272 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997351 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89831 bytes_read=2714095 bytes_retransmit=9 bytes_invalid=0 send_seq=11979 receive_seq=11979 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997794 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38201 bytes_read=521811 bytes_retransmit=9 bytes_invalid=0 send_seq=4688 receive_seq=4688 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997536 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14017 bytes_read=547734 bytes_retransmit=9 bytes_invalid=0 send_seq=2282 receive_seq=2282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14557 bytes_read=43695 bytes_retransmit=9 bytes_invalid=0 send_seq=2273 receive_seq=2273 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999456 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63129 bytes_read=986761 bytes_retransmit=0 bytes_invalid=0 send_seq=6370 receive_seq=6370 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998665 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.9 th1: temp=43.7 th2: temp=48.3 th3: temp=46.6 sysload=0.08 cputime=191.038 memavail=7397324 print_time=2183.776 buffer_time=2.016 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 97 Hz
Stats 2160.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17959882 bytes_read=2159663 bytes_retransmit=9 bytes_invalid=0 send_seq=310663 receive_seq=310663 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=22 upcoming_bytes=0 freq=400015587 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13810 bytes_read=44551 bytes_retransmit=0 bytes_invalid=0 send_seq=2273 receive_seq=2273 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997369 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89837 bytes_read=2714223 bytes_retransmit=9 bytes_invalid=0 send_seq=11980 receive_seq=11980 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997785 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38270 bytes_read=524858 bytes_retransmit=9 bytes_invalid=0 send_seq=4698 receive_seq=4698 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997537 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14023 bytes_read=547998 bytes_retransmit=9 bytes_invalid=0 send_seq=2283 receive_seq=2283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997693 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14563 bytes_read=43711 bytes_retransmit=9 bytes_invalid=0 send_seq=2274 receive_seq=2274 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999458 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63135 bytes_read=987117 bytes_retransmit=0 bytes_invalid=0 send_seq=6371 receive_seq=6371 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998667 coil_temp=17.7 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.7 th1: temp=43.9 th2: temp=48.2 th3: temp=46.8 sysload=0.08 cputime=191.142 memavail=7397328 print_time=2184.977 buffer_time=2.216 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 98 Hz
Stats 2161.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17963711 bytes_read=2160373 bytes_retransmit=9 bytes_invalid=0 send_seq=310743 receive_seq=310743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015614 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13816 bytes_read=44567 bytes_retransmit=0 bytes_invalid=0 send_seq=2274 receive_seq=2274 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997370 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89843 bytes_read=2714323 bytes_retransmit=9 bytes_invalid=0 send_seq=11981 receive_seq=11981 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997765 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38346 bytes_read=527931 bytes_retransmit=9 bytes_invalid=0 send_seq=4709 receive_seq=4709 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997543 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14029 bytes_read=548232 bytes_retransmit=9 bytes_invalid=0 send_seq=2284 receive_seq=2284 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999531 adj=47997694 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14569 bytes_read=43727 bytes_retransmit=9 bytes_invalid=0 send_seq=2275 receive_seq=2275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999457 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63141 bytes_read=987473 bytes_retransmit=0 bytes_invalid=0 send_seq=6372 receive_seq=6372 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998668 coil_temp=17.7 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.3 th1: temp=43.5 th2: temp=48.2 th3: temp=46.6 sysload=0.08 cputime=191.237 memavail=7397328 print_time=2185.908 buffer_time=2.147 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Testing frequency 99 Hz
Stats 2162.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17966776 bytes_read=2161023 bytes_retransmit=9 bytes_invalid=0 send_seq=310811 receive_seq=310811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015620 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13822 bytes_read=44596 bytes_retransmit=0 bytes_invalid=0 send_seq=2275 receive_seq=2275 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997336 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89849 bytes_read=2714451 bytes_retransmit=9 bytes_invalid=0 send_seq=11982 receive_seq=11982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997693 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38422 bytes_read=531061 bytes_retransmit=9 bytes_invalid=0 send_seq=4720 receive_seq=4720 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997525 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14035 bytes_read=548511 bytes_retransmit=9 bytes_invalid=0 send_seq=2285 receive_seq=2285 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999531 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14575 bytes_read=43754 bytes_retransmit=9 bytes_invalid=0 send_seq=2276 receive_seq=2276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999447 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63147 bytes_read=987829 bytes_retransmit=0 bytes_invalid=0 send_seq=6373 receive_seq=6373 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998644 coil_temp=17.7 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.2 th1: temp=43.8 th2: temp=48.2 th3: temp=46.6 sysload=0.07 cputime=191.332 memavail=7397328 print_time=2186.781 buffer_time=2.018 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 100 Hz
Stats 2163.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17971288 bytes_read=2161817 bytes_retransmit=9 bytes_invalid=0 send_seq=310902 receive_seq=310902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015641 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13828 bytes_read=44612 bytes_retransmit=0 bytes_invalid=0 send_seq=2276 receive_seq=2276 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997315 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89855 bytes_read=2714551 bytes_retransmit=9 bytes_invalid=0 send_seq=11983 receive_seq=11983 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997663 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38498 bytes_read=534131 bytes_retransmit=9 bytes_invalid=0 send_seq=4731 receive_seq=4731 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997495 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14041 bytes_read=548760 bytes_retransmit=9 bytes_invalid=0 send_seq=2286 receive_seq=2286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999531 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14581 bytes_read=43770 bytes_retransmit=9 bytes_invalid=0 send_seq=2277 receive_seq=2277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63153 bytes_read=988185 bytes_retransmit=0 bytes_invalid=0 send_seq=6374 receive_seq=6374 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998636 coil_temp=17.7 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.4 th1: temp=43.6 th2: temp=48.5 th3: temp=46.6 sysload=0.07 cputime=191.437 memavail=7397336 print_time=2187.978 buffer_time=2.214 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 101 Hz
Stats 2164.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17975118 bytes_read=2162507 bytes_retransmit=9 bytes_invalid=0 send_seq=310978 receive_seq=310978 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015638 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13834 bytes_read=44628 bytes_retransmit=0 bytes_invalid=0 send_seq=2277 receive_seq=2277 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997283 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89861 bytes_read=2714651 bytes_retransmit=9 bytes_invalid=0 send_seq=11984 receive_seq=11984 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997638 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38574 bytes_read=537189 bytes_retransmit=9 bytes_invalid=0 send_seq=4742 receive_seq=4742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997586 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14047 bytes_read=548994 bytes_retransmit=9 bytes_invalid=0 send_seq=2287 receive_seq=2287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999531 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14587 bytes_read=43786 bytes_retransmit=9 bytes_invalid=0 send_seq=2278 receive_seq=2278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63159 bytes_read=988541 bytes_retransmit=0 bytes_invalid=0 send_seq=6375 receive_seq=6375 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998623 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.3 th1: temp=44.0 th2: temp=48.2 th3: temp=46.7 sysload=0.07 cputime=191.533 memavail=7397336 print_time=2188.916 buffer_time=2.152 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 102 Hz
Stats 2165.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17978236 bytes_read=2163173 bytes_retransmit=9 bytes_invalid=0 send_seq=311046 receive_seq=311046 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015637 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13840 bytes_read=44644 bytes_retransmit=0 bytes_invalid=0 send_seq=2278 receive_seq=2278 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997281 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89867 bytes_read=2714793 bytes_retransmit=9 bytes_invalid=0 send_seq=11985 receive_seq=11985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997636 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38650 bytes_read=540261 bytes_retransmit=9 bytes_invalid=0 send_seq=4753 receive_seq=4753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997567 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14053 bytes_read=549288 bytes_retransmit=9 bytes_invalid=0 send_seq=2288 receive_seq=2288 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997630 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14593 bytes_read=43802 bytes_retransmit=9 bytes_invalid=0 send_seq=2279 receive_seq=2279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63165 bytes_read=988897 bytes_retransmit=0 bytes_invalid=0 send_seq=6376 receive_seq=6376 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998652 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.4 th1: temp=43.6 th2: temp=48.2 th3: temp=46.9 sysload=0.07 cputime=191.628 memavail=7397336 print_time=2189.787 buffer_time=2.023 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 103 Hz
Stats 2166.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17982802 bytes_read=2163962 bytes_retransmit=9 bytes_invalid=0 send_seq=311136 receive_seq=311136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015644 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13846 bytes_read=44660 bytes_retransmit=0 bytes_invalid=0 send_seq=2279 receive_seq=2279 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997276 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89873 bytes_read=2714893 bytes_retransmit=9 bytes_invalid=0 send_seq=11986 receive_seq=11986 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997628 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38726 bytes_read=543349 bytes_retransmit=9 bytes_invalid=0 send_seq=4764 receive_seq=4764 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997542 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14059 bytes_read=549537 bytes_retransmit=9 bytes_invalid=0 send_seq=2289 receive_seq=2289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997629 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14599 bytes_read=43818 bytes_retransmit=9 bytes_invalid=0 send_seq=2280 receive_seq=2280 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63171 bytes_read=989253 bytes_retransmit=0 bytes_invalid=0 send_seq=6377 receive_seq=6377 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998644 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.8 th1: temp=43.7 th2: temp=48.5 th3: temp=46.7 sysload=0.07 cputime=191.747 memavail=7396696 print_time=2190.988 buffer_time=2.223 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Testing frequency 104 Hz
Stats 2167.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17986776 bytes_read=2164667 bytes_retransmit=9 bytes_invalid=0 send_seq=311215 receive_seq=311215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015652 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13852 bytes_read=44689 bytes_retransmit=0 bytes_invalid=0 send_seq=2280 receive_seq=2280 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997281 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89879 bytes_read=2714993 bytes_retransmit=9 bytes_invalid=0 send_seq=11987 receive_seq=11987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997632 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38802 bytes_read=546405 bytes_retransmit=9 bytes_invalid=0 send_seq=4775 receive_seq=4775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997517 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14065 bytes_read=549771 bytes_retransmit=9 bytes_invalid=0 send_seq=2290 receive_seq=2290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997623 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14605 bytes_read=43845 bytes_retransmit=9 bytes_invalid=0 send_seq=2281 receive_seq=2281 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63177 bytes_read=989593 bytes_retransmit=0 bytes_invalid=0 send_seq=6378 receive_seq=6378 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998641 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.3 th1: temp=43.8 th2: temp=48.6 th3: temp=46.6 sysload=0.07 cputime=191.844 memavail=7396724 print_time=2191.919 buffer_time=2.152 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 105 Hz
Stats 2168.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17989927 bytes_read=2165312 bytes_retransmit=9 bytes_invalid=0 send_seq=311283 receive_seq=311283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015659 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13858 bytes_read=44705 bytes_retransmit=0 bytes_invalid=0 send_seq=2281 receive_seq=2281 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997276 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89885 bytes_read=2715121 bytes_retransmit=9 bytes_invalid=0 send_seq=11988 receive_seq=11988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997616 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38878 bytes_read=549475 bytes_retransmit=9 bytes_invalid=0 send_seq=4786 receive_seq=4786 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14071 bytes_read=550050 bytes_retransmit=9 bytes_invalid=0 send_seq=2291 receive_seq=2291 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997614 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14611 bytes_read=43861 bytes_retransmit=9 bytes_invalid=0 send_seq=2282 receive_seq=2282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63183 bytes_read=989949 bytes_retransmit=0 bytes_invalid=0 send_seq=6379 receive_seq=6379 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998641 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.5 th1: temp=44.0 th2: temp=48.2 th3: temp=46.6 sysload=0.07 cputime=191.942 memavail=7396724 print_time=2192.794 buffer_time=2.027 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 106 Hz
Stats 2169.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=17994520 bytes_read=2166106 bytes_retransmit=9 bytes_invalid=0 send_seq=311374 receive_seq=311374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=22 upcoming_bytes=0 freq=400015667 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13864 bytes_read=44721 bytes_retransmit=0 bytes_invalid=0 send_seq=2282 receive_seq=2282 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997273 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89891 bytes_read=2715221 bytes_retransmit=9 bytes_invalid=0 send_seq=11989 receive_seq=11989 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997605 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=38954 bytes_read=552605 bytes_retransmit=9 bytes_invalid=0 send_seq=4797 receive_seq=4797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997467 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14077 bytes_read=550299 bytes_retransmit=9 bytes_invalid=0 send_seq=2292 receive_seq=2292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997604 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14617 bytes_read=43877 bytes_retransmit=9 bytes_invalid=0 send_seq=2283 receive_seq=2283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63189 bytes_read=990305 bytes_retransmit=0 bytes_invalid=0 send_seq=6380 receive_seq=6380 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998627 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.5 th1: temp=43.7 th2: temp=48.3 th3: temp=46.7 sysload=0.07 cputime=192.050 memavail=7396728 print_time=2193.984 buffer_time=2.217 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 107 Hz
Stats 2170.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=17998532 bytes_read=2166802 bytes_retransmit=9 bytes_invalid=0 send_seq=311448 receive_seq=311448 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015669 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13870 bytes_read=44737 bytes_retransmit=0 bytes_invalid=0 send_seq=2283 receive_seq=2283 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997268 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89897 bytes_read=2715321 bytes_retransmit=9 bytes_invalid=0 send_seq=11990 receive_seq=11990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997619 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=39030 bytes_read=555662 bytes_retransmit=9 bytes_invalid=0 send_seq=4808 receive_seq=4808 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997461 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14083 bytes_read=550548 bytes_retransmit=9 bytes_invalid=0 send_seq=2293 receive_seq=2293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997614 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14623 bytes_read=43893 bytes_retransmit=9 bytes_invalid=0 send_seq=2284 receive_seq=2284 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63195 bytes_read=990661 bytes_retransmit=0 bytes_invalid=0 send_seq=6381 receive_seq=6381 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998623 coil_temp=17.7 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.6 th1: temp=43.7 th2: temp=48.5 th3: temp=46.8 sysload=0.07 cputime=192.146 memavail=7396728 print_time=2194.921 buffer_time=2.154 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 108 Hz
Stats 2171.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18001734 bytes_read=2167462 bytes_retransmit=9 bytes_invalid=0 send_seq=311518 receive_seq=311518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015695 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13876 bytes_read=44753 bytes_retransmit=0 bytes_invalid=0 send_seq=2284 receive_seq=2284 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997269 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89903 bytes_read=2715463 bytes_retransmit=9 bytes_invalid=0 send_seq=11991 receive_seq=11991 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997625 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=39099 bytes_read=558731 bytes_retransmit=9 bytes_invalid=0 send_seq=4818 receive_seq=4818 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997453 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14089 bytes_read=550827 bytes_retransmit=9 bytes_invalid=0 send_seq=2294 receive_seq=2294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997612 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14629 bytes_read=43909 bytes_retransmit=9 bytes_invalid=0 send_seq=2285 receive_seq=2285 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63201 bytes_read=991017 bytes_retransmit=0 bytes_invalid=0 send_seq=6382 receive_seq=6382 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998639 coil_temp=17.7 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=44.4 th1: temp=43.9 th2: temp=48.6 th3: temp=46.8 sysload=0.07 cputime=192.244 memavail=7396752 print_time=2195.797 buffer_time=2.029 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 109 Hz
Stats 2172.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18006463 bytes_read=2168276 bytes_retransmit=9 bytes_invalid=0 send_seq=311613 receive_seq=311613 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=0 freq=400015702 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13882 bytes_read=44769 bytes_retransmit=0 bytes_invalid=0 send_seq=2285 receive_seq=2285 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997225 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89909 bytes_read=2715563 bytes_retransmit=9 bytes_invalid=0 send_seq=11992 receive_seq=11992 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997569 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=39175 bytes_read=561801 bytes_retransmit=9 bytes_invalid=0 send_seq=4829 receive_seq=4829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997391 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14095 bytes_read=551076 bytes_retransmit=9 bytes_invalid=0 send_seq=2295 receive_seq=2295 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997570 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14635 bytes_read=43936 bytes_retransmit=9 bytes_invalid=0 send_seq=2286 receive_seq=2286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999431 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63207 bytes_read=991373 bytes_retransmit=0 bytes_invalid=0 send_seq=6383 receive_seq=6383 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998607 coil_temp=17.7 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=44.5 th1: temp=43.7 th2: temp=48.2 th3: temp=46.9 sysload=0.06 cputime=192.354 memavail=7396752 print_time=2197.001 buffer_time=2.232 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 110 Hz
Stats 2173.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18010605 bytes_read=2169011 bytes_retransmit=9 bytes_invalid=0 send_seq=311698 receive_seq=311698 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015706 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13888 bytes_read=44798 bytes_retransmit=0 bytes_invalid=0 send_seq=2286 receive_seq=2286 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997226 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89915 bytes_read=2715663 bytes_retransmit=9 bytes_invalid=0 send_seq=11993 receive_seq=11993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997595 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=39251 bytes_read=564857 bytes_retransmit=9 bytes_invalid=0 send_seq=4840 receive_seq=4840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997419 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14101 bytes_read=551310 bytes_retransmit=9 bytes_invalid=0 send_seq=2296 receive_seq=2296 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997581 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14641 bytes_read=43952 bytes_retransmit=9 bytes_invalid=0 send_seq=2287 receive_seq=2287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999432 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63213 bytes_read=991729 bytes_retransmit=0 bytes_invalid=0 send_seq=6384 receive_seq=6384 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998610 coil_temp=17.7 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=44.6 th1: temp=43.7 th2: temp=48.3 th3: temp=46.8 sysload=0.06 cputime=192.452 memavail=7396764 print_time=2197.928 buffer_time=2.158 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 111 Hz
Stats 2174.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18013824 bytes_read=2169666 bytes_retransmit=9 bytes_invalid=0 send_seq=311767 receive_seq=311767 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015704 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13894 bytes_read=44814 bytes_retransmit=0 bytes_invalid=0 send_seq=2287 receive_seq=2287 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997265 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89921 bytes_read=2715791 bytes_retransmit=9 bytes_invalid=0 send_seq=11994 receive_seq=11994 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997592 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=39327 bytes_read=567946 bytes_retransmit=9 bytes_invalid=0 send_seq=4851 receive_seq=4851 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997415 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14107 bytes_read=551589 bytes_retransmit=9 bytes_invalid=0 send_seq=2297 receive_seq=2297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997581 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14647 bytes_read=43968 bytes_retransmit=9 bytes_invalid=0 send_seq=2288 receive_seq=2288 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999432 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63219 bytes_read=992085 bytes_retransmit=0 bytes_invalid=0 send_seq=6385 receive_seq=6385 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998608 coil_temp=17.7 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=44.5 th1: temp=44.0 th2: temp=48.6 th3: temp=46.6 sysload=0.06 cputime=192.550 memavail=7396764 print_time=2198.803 buffer_time=2.032 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 112 Hz
Stats 2175.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18018504 bytes_read=2170486 bytes_retransmit=9 bytes_invalid=0 send_seq=311860 receive_seq=311860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=0 freq=400015740 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13900 bytes_read=44830 bytes_retransmit=0 bytes_invalid=0 send_seq=2288 receive_seq=2288 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999268 adj=49997279 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89927 bytes_read=2715891 bytes_retransmit=9 bytes_invalid=0 send_seq=11995 receive_seq=11995 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997708 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=39403 bytes_read=571002 bytes_retransmit=9 bytes_invalid=0 send_seq=4862 receive_seq=4862 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997428 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14113 bytes_read=551853 bytes_retransmit=9 bytes_invalid=0 send_seq=2298 receive_seq=2298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997589 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14653 bytes_read=43984 bytes_retransmit=9 bytes_invalid=0 send_seq=2289 receive_seq=2289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999433 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63225 bytes_read=992441 bytes_retransmit=0 bytes_invalid=0 send_seq=6386 receive_seq=6386 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998620 coil_temp=17.7 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=44.3 th1: temp=43.8 th2: temp=48.5 th3: temp=46.7 sysload=0.06 cputime=192.661 memavail=7396764 print_time=2199.998 buffer_time=2.228 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 113 Hz
Stats 2176.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18022713 bytes_read=2171226 bytes_retransmit=9 bytes_invalid=0 send_seq=311946 receive_seq=311946 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015746 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13906 bytes_read=44846 bytes_retransmit=0 bytes_invalid=0 send_seq=2289 receive_seq=2289 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999266 adj=49997425 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89933 bytes_read=2716005 bytes_retransmit=9 bytes_invalid=0 send_seq=11996 receive_seq=11996 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997636 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=39479 bytes_read=574136 bytes_retransmit=9 bytes_invalid=0 send_seq=4873 receive_seq=4873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997379 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14119 bytes_read=552087 bytes_retransmit=9 bytes_invalid=0 send_seq=2299 receive_seq=2299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997554 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14659 bytes_read=44000 bytes_retransmit=9 bytes_invalid=0 send_seq=2290 receive_seq=2290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999425 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63231 bytes_read=992797 bytes_retransmit=0 bytes_invalid=0 send_seq=6387 receive_seq=6387 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998598 coil_temp=17.7 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=44.5 th1: temp=43.9 th2: temp=48.5 th3: temp=46.7 sysload=0.06 cputime=192.763 memavail=7396048 print_time=2200.937 buffer_time=2.165 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 114 Hz
Stats 2177.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18025920 bytes_read=2171881 bytes_retransmit=9 bytes_invalid=0 send_seq=312015 receive_seq=312015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015753 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13912 bytes_read=44862 bytes_retransmit=0 bytes_invalid=0 send_seq=2290 receive_seq=2290 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999265 adj=49997385 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89939 bytes_read=2716133 bytes_retransmit=9 bytes_invalid=0 send_seq=11997 receive_seq=11997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997696 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=39555 bytes_read=577224 bytes_retransmit=9 bytes_invalid=0 send_seq=4884 receive_seq=4884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997375 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14125 bytes_read=552381 bytes_retransmit=9 bytes_invalid=0 send_seq=2300 receive_seq=2300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997556 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14665 bytes_read=44027 bytes_retransmit=9 bytes_invalid=0 send_seq=2291 receive_seq=2291 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999424 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63237 bytes_read=993153 bytes_retransmit=0 bytes_invalid=0 send_seq=6388 receive_seq=6388 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998594 coil_temp=17.7 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=44.6 th1: temp=43.9 th2: temp=48.8 th3: temp=46.9 sysload=0.06 cputime=192.863 memavail=7396056 print_time=2201.806 buffer_time=2.033 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 115 Hz
Stats 2178.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18030757 bytes_read=2172703 bytes_retransmit=9 bytes_invalid=0 send_seq=312112 receive_seq=312112 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=0 freq=400015756 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13918 bytes_read=44891 bytes_retransmit=0 bytes_invalid=0 send_seq=2291 receive_seq=2291 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999263 adj=49997344 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89945 bytes_read=2716233 bytes_retransmit=9 bytes_invalid=0 send_seq=11998 receive_seq=11998 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997657 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=39631 bytes_read=580280 bytes_retransmit=9 bytes_invalid=0 send_seq=4895 receive_seq=4895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997372 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14131 bytes_read=552615 bytes_retransmit=9 bytes_invalid=0 send_seq=2301 receive_seq=2301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997551 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14671 bytes_read=44043 bytes_retransmit=9 bytes_invalid=0 send_seq=2292 receive_seq=2292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999424 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63243 bytes_read=993509 bytes_retransmit=0 bytes_invalid=0 send_seq=6389 receive_seq=6389 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998587 coil_temp=17.7 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=44.6 th1: temp=43.9 th2: temp=48.3 th3: temp=47.3 sysload=0.06 cputime=192.974 memavail=7396056 print_time=2203.005 buffer_time=2.232 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 116 Hz
Stats 2179.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18035061 bytes_read=2173448 bytes_retransmit=9 bytes_invalid=0 send_seq=312200 receive_seq=312200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015748 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13924 bytes_read=44907 bytes_retransmit=0 bytes_invalid=0 send_seq=2292 receive_seq=2292 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999262 adj=49997307 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89951 bytes_read=2716333 bytes_retransmit=9 bytes_invalid=0 send_seq=11999 receive_seq=11999 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997709 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=39707 bytes_read=583336 bytes_retransmit=9 bytes_invalid=0 send_seq=4906 receive_seq=4906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997400 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14137 bytes_read=552849 bytes_retransmit=9 bytes_invalid=0 send_seq=2302 receive_seq=2302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997571 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14677 bytes_read=44059 bytes_retransmit=9 bytes_invalid=0 send_seq=2293 receive_seq=2293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999428 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63249 bytes_read=993865 bytes_retransmit=0 bytes_invalid=0 send_seq=6390 receive_seq=6390 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998599 coil_temp=17.7 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=44.7 th1: temp=44.0 th2: temp=49.0 th3: temp=46.9 sysload=0.06 cputime=193.075 memavail=7396060 print_time=2203.941 buffer_time=2.166 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 117 Hz
Stats 2180.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18038266 bytes_read=2174114 bytes_retransmit=9 bytes_invalid=0 send_seq=312268 receive_seq=312268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015753 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13930 bytes_read=44923 bytes_retransmit=0 bytes_invalid=0 send_seq=2293 receive_seq=2293 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999261 adj=49997299 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89957 bytes_read=2716461 bytes_retransmit=9 bytes_invalid=0 send_seq=12000 receive_seq=12000 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997773 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=39783 bytes_read=586421 bytes_retransmit=9 bytes_invalid=0 send_seq=4917 receive_seq=4917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997419 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14143 bytes_read=553158 bytes_retransmit=9 bytes_invalid=0 send_seq=2303 receive_seq=2303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997592 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14683 bytes_read=44075 bytes_retransmit=9 bytes_invalid=0 send_seq=2294 receive_seq=2294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999433 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63255 bytes_read=994221 bytes_retransmit=0 bytes_invalid=0 send_seq=6391 receive_seq=6391 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998609 coil_temp=17.7 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=44.8 th1: temp=44.0 th2: temp=48.4 th3: temp=47.0 sysload=0.06 cputime=193.176 memavail=7396064 print_time=2204.807 buffer_time=2.032 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 118 Hz
Stats 2181.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18043154 bytes_read=2174943 bytes_retransmit=9 bytes_invalid=0 send_seq=312366 receive_seq=312366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=0 freq=400015751 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13936 bytes_read=44939 bytes_retransmit=0 bytes_invalid=0 send_seq=2294 receive_seq=2294 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999262 adj=49997278 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89963 bytes_read=2716575 bytes_retransmit=9 bytes_invalid=0 send_seq=12001 receive_seq=12001 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997728 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=39859 bytes_read=589495 bytes_retransmit=9 bytes_invalid=0 send_seq=4928 receive_seq=4928 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997408 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14149 bytes_read=553392 bytes_retransmit=9 bytes_invalid=0 send_seq=2304 receive_seq=2304 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997587 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14689 bytes_read=44091 bytes_retransmit=9 bytes_invalid=0 send_seq=2295 receive_seq=2295 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999432 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63261 bytes_read=994577 bytes_retransmit=0 bytes_invalid=0 send_seq=6392 receive_seq=6392 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998607 coil_temp=17.7 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=44.6 th1: temp=44.1 th2: temp=48.6 th3: temp=47.0 sysload=0.06 cputime=193.291 memavail=7396076 print_time=2206.016 buffer_time=2.240 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 119 Hz
Stats 2182.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18047373 bytes_read=2175638 bytes_retransmit=9 bytes_invalid=0 send_seq=312443 receive_seq=312443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015755 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13942 bytes_read=44955 bytes_retransmit=0 bytes_invalid=0 send_seq=2295 receive_seq=2295 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999261 adj=49997295 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89969 bytes_read=2716675 bytes_retransmit=9 bytes_invalid=0 send_seq=12002 receive_seq=12002 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997708 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=39935 bytes_read=592552 bytes_retransmit=9 bytes_invalid=0 send_seq=4939 receive_seq=4939 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000034 adj=63997447 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14155 bytes_read=553626 bytes_retransmit=9 bytes_invalid=0 send_seq=2305 receive_seq=2305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997606 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14695 bytes_read=44118 bytes_retransmit=9 bytes_invalid=0 send_seq=2296 receive_seq=2296 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63267 bytes_read=994933 bytes_retransmit=0 bytes_invalid=0 send_seq=6393 receive_seq=6393 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998636 coil_temp=17.7 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=44.6 th1: temp=44.1 th2: temp=48.7 th3: temp=47.1 sysload=0.05 cputime=193.395 memavail=7396076 print_time=2206.944 buffer_time=2.169 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 120 Hz
Stats 2183.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18050654 bytes_read=2176298 bytes_retransmit=9 bytes_invalid=0 send_seq=312513 receive_seq=312513 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015753 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13948 bytes_read=44984 bytes_retransmit=0 bytes_invalid=0 send_seq=2296 receive_seq=2296 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999261 adj=49997285 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89975 bytes_read=2716803 bytes_retransmit=9 bytes_invalid=0 send_seq=12003 receive_seq=12003 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997676 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40011 bytes_read=595694 bytes_retransmit=9 bytes_invalid=0 send_seq=4950 receive_seq=4950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997442 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14161 bytes_read=553920 bytes_retransmit=9 bytes_invalid=0 send_seq=2306 receive_seq=2306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997606 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14701 bytes_read=44134 bytes_retransmit=9 bytes_invalid=0 send_seq=2297 receive_seq=2297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63273 bytes_read=995289 bytes_retransmit=0 bytes_invalid=0 send_seq=6394 receive_seq=6394 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998646 coil_temp=17.7 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=44.4 th1: temp=44.0 th2: temp=48.7 th3: temp=47.1 sysload=0.05 cputime=193.507 memavail=7390292 print_time=2207.812 buffer_time=2.035 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 121 Hz
Stats 2184.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18055572 bytes_read=2177112 bytes_retransmit=9 bytes_invalid=0 send_seq=312608 receive_seq=312608 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=0 freq=400015969 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13954 bytes_read=45000 bytes_retransmit=0 bytes_invalid=0 send_seq=2297 receive_seq=2297 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999260 adj=49997281 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89981 bytes_read=2716903 bytes_retransmit=9 bytes_invalid=0 send_seq=12004 receive_seq=12004 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997658 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40087 bytes_read=598751 bytes_retransmit=9 bytes_invalid=0 send_seq=4961 receive_seq=4961 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997518 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14167 bytes_read=554154 bytes_retransmit=9 bytes_invalid=0 send_seq=2307 receive_seq=2307 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14707 bytes_read=44150 bytes_retransmit=9 bytes_invalid=0 send_seq=2298 receive_seq=2298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63279 bytes_read=995645 bytes_retransmit=0 bytes_invalid=0 send_seq=6395 receive_seq=6395 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998662 coil_temp=17.7 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=44.1 th1: temp=44.0 th2: temp=48.7 th3: temp=46.9 sysload=0.05 cputime=193.622 memavail=7396460 print_time=2209.020 buffer_time=2.242 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 122 Hz
Stats 2185.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18059923 bytes_read=2177863 bytes_retransmit=9 bytes_invalid=0 send_seq=312693 receive_seq=312693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015958 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13960 bytes_read=45016 bytes_retransmit=0 bytes_invalid=0 send_seq=2298 receive_seq=2298 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999260 adj=49996955 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89987 bytes_read=2717003 bytes_retransmit=9 bytes_invalid=0 send_seq=12005 receive_seq=12005 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997252 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40156 bytes_read=601784 bytes_retransmit=9 bytes_invalid=0 send_seq=4971 receive_seq=4971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997095 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14173 bytes_read=554403 bytes_retransmit=9 bytes_invalid=0 send_seq=2308 receive_seq=2308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997328 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14713 bytes_read=44166 bytes_retransmit=9 bytes_invalid=0 send_seq=2299 receive_seq=2299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999364 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=31.1 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63285 bytes_read=996001 bytes_retransmit=0 bytes_invalid=0 send_seq=6396 receive_seq=6396 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998462 coil_temp=17.7 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=44.8 th1: temp=44.4 th2: temp=48.6 th3: temp=47.1 sysload=0.05 cputime=193.725 memavail=7396460 print_time=2209.944 buffer_time=2.166 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 123 Hz
Stats 2186.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18063213 bytes_read=2178523 bytes_retransmit=9 bytes_invalid=0 send_seq=312763 receive_seq=312763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016006 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13966 bytes_read=45032 bytes_retransmit=0 bytes_invalid=0 send_seq=2299 receive_seq=2299 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999260 adj=49997012 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89993 bytes_read=2717145 bytes_retransmit=9 bytes_invalid=0 send_seq=12006 receive_seq=12006 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997307 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40232 bytes_read=604887 bytes_retransmit=9 bytes_invalid=0 send_seq=4982 receive_seq=4982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997160 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14179 bytes_read=554697 bytes_retransmit=9 bytes_invalid=0 send_seq=2309 receive_seq=2309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997385 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14719 bytes_read=44182 bytes_retransmit=9 bytes_invalid=0 send_seq=2300 receive_seq=2300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999377 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63291 bytes_read=996357 bytes_retransmit=0 bytes_invalid=0 send_seq=6397 receive_seq=6397 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998496 coil_temp=17.7 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=44.7 th1: temp=43.9 th2: temp=48.5 th3: temp=47.1 sysload=0.05 cputime=193.829 memavail=7396232 print_time=2210.812 buffer_time=2.034 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 124 Hz
Stats 2187.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18068197 bytes_read=2179327 bytes_retransmit=9 bytes_invalid=0 send_seq=312856 receive_seq=312856 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=0 freq=400016034 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=13972 bytes_read=45048 bytes_retransmit=0 bytes_invalid=0 send_seq=2300 receive_seq=2300 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999259 adj=49996956 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=89999 bytes_read=2717245 bytes_retransmit=9 bytes_invalid=0 send_seq=12007 receive_seq=12007 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997231 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40308 bytes_read=607945 bytes_retransmit=9 bytes_invalid=0 send_seq=4993 receive_seq=4993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997082 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14185 bytes_read=554931 bytes_retransmit=9 bytes_invalid=0 send_seq=2310 receive_seq=2310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997335 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14725 bytes_read=44209 bytes_retransmit=9 bytes_invalid=0 send_seq=2301 receive_seq=2301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999366 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63297 bytes_read=996713 bytes_retransmit=0 bytes_invalid=0 send_seq=6398 receive_seq=6398 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998460 coil_temp=17.7 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.8 th1: temp=44.1 th2: temp=48.9 th3: temp=47.1 sysload=0.05 cputime=193.945 memavail=7396232 print_time=2212.019 buffer_time=2.240 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 125 Hz
Stats 2188.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18072592 bytes_read=2180072 bytes_retransmit=9 bytes_invalid=0 send_seq=312943 receive_seq=312943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400016133 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13978 bytes_read=45077 bytes_retransmit=0 bytes_invalid=0 send_seq=2301 receive_seq=2301 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999260 adj=49997006 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=90005 bytes_read=2717345 bytes_retransmit=9 bytes_invalid=0 send_seq=12008 receive_seq=12008 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997309 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40384 bytes_read=611002 bytes_retransmit=9 bytes_invalid=0 send_seq=5004 receive_seq=5004 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997142 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14191 bytes_read=555165 bytes_retransmit=9 bytes_invalid=0 send_seq=2311 receive_seq=2311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997381 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14731 bytes_read=44225 bytes_retransmit=9 bytes_invalid=0 send_seq=2302 receive_seq=2302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999377 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63303 bytes_read=997069 bytes_retransmit=0 bytes_invalid=0 send_seq=6399 receive_seq=6399 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998487 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.6 th1: temp=44.1 th2: temp=48.7 th3: temp=47.0 sysload=0.05 cputime=194.051 memavail=7396232 print_time=2212.949 buffer_time=2.170 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 126 Hz
Stats 2189.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18075923 bytes_read=2180735 bytes_retransmit=9 bytes_invalid=0 send_seq=313014 receive_seq=313014 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016170 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13984 bytes_read=45093 bytes_retransmit=0 bytes_invalid=0 send_seq=2302 receive_seq=2302 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999261 adj=49996893 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=90011 bytes_read=2717473 bytes_retransmit=9 bytes_invalid=0 send_seq=12009 receive_seq=12009 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997168 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40460 bytes_read=614091 bytes_retransmit=9 bytes_invalid=0 send_seq=5015 receive_seq=5015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997090 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14197 bytes_read=555459 bytes_retransmit=9 bytes_invalid=0 send_seq=2312 receive_seq=2312 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997266 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14737 bytes_read=44241 bytes_retransmit=9 bytes_invalid=0 send_seq=2303 receive_seq=2303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999352 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63309 bytes_read=997425 bytes_retransmit=0 bytes_invalid=0 send_seq=6400 receive_seq=6400 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998404 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.8 th1: temp=44.4 th2: temp=48.6 th3: temp=46.9 sysload=0.05 cputime=194.155 memavail=7396232 print_time=2213.819 buffer_time=2.039 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 127 Hz
Stats 2190.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18080980 bytes_read=2181572 bytes_retransmit=9 bytes_invalid=0 send_seq=313111 receive_seq=313111 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400016150 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13990 bytes_read=45109 bytes_retransmit=0 bytes_invalid=0 send_seq=2303 receive_seq=2303 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999259 adj=49996884 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=90017 bytes_read=2717573 bytes_retransmit=9 bytes_invalid=0 send_seq=12010 receive_seq=12010 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997128 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40536 bytes_read=617149 bytes_retransmit=9 bytes_invalid=0 send_seq=5026 receive_seq=5026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997045 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14203 bytes_read=555708 bytes_retransmit=9 bytes_invalid=0 send_seq=2313 receive_seq=2313 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997245 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14743 bytes_read=44257 bytes_retransmit=9 bytes_invalid=0 send_seq=2304 receive_seq=2304 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999346 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=31.1 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63315 bytes_read=997781 bytes_retransmit=0 bytes_invalid=0 send_seq=6401 receive_seq=6401 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998390 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.8 th1: temp=44.0 th2: temp=48.9 th3: temp=47.2 sysload=0.05 cputime=194.275 memavail=7396232 print_time=2215.023 buffer_time=2.242 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 128 Hz
Stats 2191.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18085313 bytes_read=2182317 bytes_retransmit=9 bytes_invalid=0 send_seq=313198 receive_seq=313198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=0 freq=400016116 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=13996 bytes_read=45125 bytes_retransmit=0 bytes_invalid=0 send_seq=2304 receive_seq=2304 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999259 adj=49997007 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=90023 bytes_read=2717681 bytes_retransmit=9 bytes_invalid=0 send_seq=12011 receive_seq=12011 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997300 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40612 bytes_read=620270 bytes_retransmit=9 bytes_invalid=0 send_seq=5037 receive_seq=5037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997209 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14209 bytes_read=555942 bytes_retransmit=9 bytes_invalid=0 send_seq=2314 receive_seq=2314 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997377 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14749 bytes_read=44273 bytes_retransmit=9 bytes_invalid=0 send_seq=2305 receive_seq=2305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999378 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63321 bytes_read=998137 bytes_retransmit=0 bytes_invalid=0 send_seq=6402 receive_seq=6402 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998477 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.9 th1: temp=44.0 th2: temp=48.7 th3: temp=47.2 sysload=0.05 cputime=194.381 memavail=7396232 print_time=2215.950 buffer_time=2.170 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 129 Hz
Stats 2192.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18088743 bytes_read=2182987 bytes_retransmit=9 bytes_invalid=0 send_seq=313270 receive_seq=313270 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016112 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14002 bytes_read=45141 bytes_retransmit=0 bytes_invalid=0 send_seq=2305 receive_seq=2305 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997079 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=90029 bytes_read=2717800 bytes_retransmit=9 bytes_invalid=0 send_seq=12012 receive_seq=12012 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997389 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40688 bytes_read=623336 bytes_retransmit=9 bytes_invalid=0 send_seq=5048 receive_seq=5048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997295 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14215 bytes_read=556236 bytes_retransmit=9 bytes_invalid=0 send_seq=2315 receive_seq=2315 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999531 adj=47997456 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14755 bytes_read=44299 bytes_retransmit=9 bytes_invalid=0 send_seq=2306 receive_seq=2306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999397 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63327 bytes_read=998493 bytes_retransmit=0 bytes_invalid=0 send_seq=6403 receive_seq=6403 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998531 coil_temp=17.7 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=44.5 th1: temp=44.0 th2: temp=48.8 th3: temp=47.1 sysload=0.04 cputime=194.486 memavail=7396252 print_time=2216.827 buffer_time=2.046 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 130 Hz
Stats 2193.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18093782 bytes_read=2183821 bytes_retransmit=9 bytes_invalid=0 send_seq=313369 receive_seq=313369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=0 freq=400016097 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14008 bytes_read=45170 bytes_retransmit=0 bytes_invalid=0 send_seq=2306 receive_seq=2306 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997086 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=90035 bytes_read=2717893 bytes_retransmit=9 bytes_invalid=0 send_seq=12013 receive_seq=12013 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997407 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40764 bytes_read=626375 bytes_retransmit=9 bytes_invalid=0 send_seq=5059 receive_seq=5059 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997303 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14221 bytes_read=556470 bytes_retransmit=9 bytes_invalid=0 send_seq=2316 receive_seq=2316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997487 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14761 bytes_read=44314 bytes_retransmit=9 bytes_invalid=0 send_seq=2307 receive_seq=2307 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999404 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63333 bytes_read=998849 bytes_retransmit=0 bytes_invalid=0 send_seq=6404 receive_seq=6404 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998546 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.9 th1: temp=44.1 th2: temp=48.8 th3: temp=47.0 sysload=0.04 cputime=194.619 memavail=7396516 print_time=2218.026 buffer_time=2.244 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 131 Hz
Stats 2194.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18098189 bytes_read=2184571 bytes_retransmit=9 bytes_invalid=0 send_seq=313457 receive_seq=313457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=31 freq=400016082 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14014 bytes_read=45186 bytes_retransmit=0 bytes_invalid=0 send_seq=2307 receive_seq=2307 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997154 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=90041 bytes_read=2717986 bytes_retransmit=9 bytes_invalid=0 send_seq=12014 receive_seq=12014 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997560 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40840 bytes_read=629416 bytes_retransmit=9 bytes_invalid=0 send_seq=5070 receive_seq=5070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997381 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14227 bytes_read=556704 bytes_retransmit=9 bytes_invalid=0 send_seq=2317 receive_seq=2317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997541 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14767 bytes_read=44329 bytes_retransmit=9 bytes_invalid=0 send_seq=2308 receive_seq=2308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999419 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63339 bytes_read=999205 bytes_retransmit=0 bytes_invalid=0 send_seq=6405 receive_seq=6405 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998578 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.5 th1: temp=44.3 th2: temp=48.8 th3: temp=47.1 sysload=0.04 cputime=194.728 memavail=7396516 print_time=2218.952 buffer_time=2.169 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 132 Hz
Stats 2195.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18101720 bytes_read=2185272 bytes_retransmit=9 bytes_invalid=0 send_seq=313532 receive_seq=313532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016061 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14020 bytes_read=45202 bytes_retransmit=0 bytes_invalid=0 send_seq=2308 receive_seq=2308 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997193 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=90047 bytes_read=2718111 bytes_retransmit=9 bytes_invalid=0 send_seq=12015 receive_seq=12015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997690 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40916 bytes_read=632491 bytes_retransmit=9 bytes_invalid=0 send_seq=5081 receive_seq=5081 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997422 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14233 bytes_read=557013 bytes_retransmit=9 bytes_invalid=0 send_seq=2318 receive_seq=2318 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997568 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14773 bytes_read=44344 bytes_retransmit=9 bytes_invalid=0 send_seq=2309 receive_seq=2309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999425 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63345 bytes_read=999561 bytes_retransmit=0 bytes_invalid=0 send_seq=6406 receive_seq=6406 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998593 coil_temp=17.7 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=45.0 th1: temp=44.4 th2: temp=48.9 th3: temp=47.4 sysload=0.04 cputime=194.835 memavail=7396516 print_time=2219.827 buffer_time=2.043 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Stats 2196.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18106504 bytes_read=2186081 bytes_retransmit=9 bytes_invalid=0 send_seq=313626 receive_seq=313626 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=47 upcoming_bytes=0 freq=400016056 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14026 bytes_read=45218 bytes_retransmit=0 bytes_invalid=0 send_seq=2309 receive_seq=2309 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997232 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=90053 bytes_read=2718225 bytes_retransmit=9 bytes_invalid=0 send_seq=12016 receive_seq=12016 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997782 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=40992 bytes_read=635566 bytes_retransmit=9 bytes_invalid=0 send_seq=5092 receive_seq=5092 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997457 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14239 bytes_read=557247 bytes_retransmit=9 bytes_invalid=0 send_seq=2319 receive_seq=2319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997603 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14779 bytes_read=44359 bytes_retransmit=9 bytes_invalid=0 send_seq=2310 receive_seq=2310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999433 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63351 bytes_read=999917 bytes_retransmit=0 bytes_invalid=0 send_seq=6407 receive_seq=6407 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998631 coil_temp=17.7 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=45.0 th1: temp=44.3 th2: temp=48.6 th3: temp=47.1 sysload=0.04 cputime=194.949 memavail=7396776 print_time=2220.804 buffer_time=2.020 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2197.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18106849 bytes_read=2186506 bytes_retransmit=9 bytes_invalid=0 send_seq=313649 receive_seq=313649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016044 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14032 bytes_read=45234 bytes_retransmit=0 bytes_invalid=0 send_seq=2310 receive_seq=2310 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999260 adj=49997251 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=90059 bytes_read=2718325 bytes_retransmit=9 bytes_invalid=0 send_seq=12017 receive_seq=12017 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997740 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=41068 bytes_read=638622 bytes_retransmit=9 bytes_invalid=0 send_seq=5103 receive_seq=5103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997462 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14245 bytes_read=557481 bytes_retransmit=9 bytes_invalid=0 send_seq=2320 receive_seq=2320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999531 adj=47997615 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14785 bytes_read=44385 bytes_retransmit=9 bytes_invalid=0 send_seq=2311 receive_seq=2311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63357 bytes_read=1000273 bytes_retransmit=0 bytes_invalid=0 send_seq=6408 receive_seq=6408 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998647 coil_temp=17.7 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=45.0 th1: temp=44.5 th2: temp=48.9 th3: temp=47.2 sysload=0.04 cputime=195.010 memavail=7396776 print_time=2220.804 buffer_time=1.020 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2198.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18107142 bytes_read=2186926 bytes_retransmit=9 bytes_invalid=0 send_seq=313671 receive_seq=313671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016010 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14038 bytes_read=45263 bytes_retransmit=0 bytes_invalid=0 send_seq=2311 receive_seq=2311 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999260 adj=49997296 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=90065 bytes_read=2718453 bytes_retransmit=9 bytes_invalid=0 send_seq=12018 receive_seq=12018 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997749 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=41137 bytes_read=641743 bytes_retransmit=9 bytes_invalid=0 send_seq=5113 receive_seq=5113 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997482 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14251 bytes_read=557775 bytes_retransmit=9 bytes_invalid=0 send_seq=2321 receive_seq=2321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999532 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14791 bytes_read=44400 bytes_retransmit=9 bytes_invalid=0 send_seq=2312 receive_seq=2312 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63363 bytes_read=1000629 bytes_retransmit=0 bytes_invalid=0 send_seq=6409 receive_seq=6409 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998658 coil_temp=17.7 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=44.8 th1: temp=44.2 th2: temp=48.9 th3: temp=47.1 sysload=0.04 cputime=195.073 memavail=7397036 print_time=2220.804 buffer_time=0.019 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Writing raw accelerometer data to /tmp/raw_data_x_toolboard_t1_t1.csv file
RatOS | IDEX:: Selecting T0..
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 20.000000
RatOS | IDEX:: Toolhead offset applied for T0: X=0 Y=0 Z=0
Activating extruder extruder
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
Probing point (250.000, 250.000, 20.000)
LIS2DW finished 'toolboard_t1' measurements
Stats 2199.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18110218 bytes_read=2187600 bytes_retransmit=9 bytes_invalid=0 send_seq=313738 receive_seq=313738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016009 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14044 bytes_read=45279 bytes_retransmit=0 bytes_invalid=0 send_seq=2312 receive_seq=2312 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999260 adj=49997350 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=90071 bytes_read=2718553 bytes_retransmit=9 bytes_invalid=0 send_seq=12019 receive_seq=12019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997797 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=41200 bytes_read=642335 bytes_retransmit=9 bytes_invalid=0 send_seq=5120 receive_seq=5120 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997543 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14257 bytes_read=558009 bytes_retransmit=9 bytes_invalid=0 send_seq=2322 receive_seq=2322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997706 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14797 bytes_read=44415 bytes_retransmit=9 bytes_invalid=0 send_seq=2313 receive_seq=2313 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999453 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63369 bytes_read=1000985 bytes_retransmit=0 bytes_invalid=0 send_seq=6410 receive_seq=6410 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998694 coil_temp=17.7 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=44.8 th1: temp=44.5 th2: temp=48.9 th3: temp=47.2 sysload=0.04 cputime=195.240 memavail=7399964 print_time=2222.110 buffer_time=0.324 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t0' measurements
toolhead: max_velocity: 600.000000
max_accel: 8379.841000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance testing
Testing frequency 10 Hz
Testing frequency 11 Hz
Testing frequency 12 Hz
Stats 2200.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18112814 bytes_read=2188221 bytes_retransmit=9 bytes_invalid=0 send_seq=313798 receive_seq=313798 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015983 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14050 bytes_read=45295 bytes_retransmit=0 bytes_invalid=0 send_seq=2313 receive_seq=2313 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999260 adj=49997360 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=90226 bytes_read=2720561 bytes_retransmit=9 bytes_invalid=0 send_seq=12037 receive_seq=12037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997764 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=41206 bytes_read=642435 bytes_retransmit=9 bytes_invalid=0 send_seq=5121 receive_seq=5121 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997530 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14263 bytes_read=558258 bytes_retransmit=9 bytes_invalid=0 send_seq=2323 receive_seq=2323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999533 adj=47997721 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14803 bytes_read=44430 bytes_retransmit=9 bytes_invalid=0 send_seq=2314 receive_seq=2314 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63375 bytes_read=1001341 bytes_retransmit=0 bytes_invalid=0 send_seq=6411 receive_seq=6411 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998694 coil_temp=17.7 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=45.0 th1: temp=44.3 th2: temp=48.6 th3: temp=47.4 sysload=0.04 cputime=195.405 memavail=7392404 print_time=2225.277 buffer_time=2.491 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2201.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18113763 bytes_read=2188706 bytes_retransmit=9 bytes_invalid=0 send_seq=313831 receive_seq=313831 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015939 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14062 bytes_read=45327 bytes_retransmit=0 bytes_invalid=0 send_seq=2315 receive_seq=2315 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999261 adj=49997309 toolboard_t0: mcu_awake=0.061 mcu_task_avg=0.000094 mcu_task_stddev=0.000074 bytes_write=90308 bytes_read=2723621 bytes_retransmit=9 bytes_invalid=0 send_seq=12049 receive_seq=12049 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997707 toolboard_t1: mcu_awake=0.155 mcu_task_avg=0.000111 mcu_task_stddev=0.000071 bytes_write=41218 bytes_read=642596 bytes_retransmit=9 bytes_invalid=0 send_seq=5123 receive_seq=5123 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14275 bytes_read=558568 bytes_retransmit=9 bytes_invalid=0 send_seq=2325 receive_seq=2325 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14815 bytes_read=44460 bytes_retransmit=9 bytes_invalid=0 send_seq=2316 receive_seq=2316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63387 bytes_read=1001713 bytes_retransmit=0 bytes_invalid=0 send_seq=6413 receive_seq=6413 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998666 coil_temp=17.7 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=44.7 th1: temp=44.0 th2: temp=48.9 th3: temp=47.1 sysload=0.04 cputime=195.475 memavail=7399576 print_time=2225.871 buffer_time=2.084 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 13 Hz
Testing frequency 14 Hz
Stats 2202.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18115422 bytes_read=2189270 bytes_retransmit=9 bytes_invalid=0 send_seq=313876 receive_seq=313876 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015946 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14068 bytes_read=45343 bytes_retransmit=0 bytes_invalid=0 send_seq=2316 receive_seq=2316 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999261 adj=49997378 toolboard_t0: mcu_awake=0.061 mcu_task_avg=0.000094 mcu_task_stddev=0.000074 bytes_write=90384 bytes_read=2726654 bytes_retransmit=9 bytes_invalid=0 send_seq=12060 receive_seq=12060 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997756 toolboard_t1: mcu_awake=0.155 mcu_task_avg=0.000111 mcu_task_stddev=0.000071 bytes_write=41224 bytes_read=642696 bytes_retransmit=9 bytes_invalid=0 send_seq=5124 receive_seq=5124 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997613 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14281 bytes_read=558802 bytes_retransmit=9 bytes_invalid=0 send_seq=2326 receive_seq=2326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997790 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14821 bytes_read=44486 bytes_retransmit=9 bytes_invalid=0 send_seq=2317 receive_seq=2317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999463 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63393 bytes_read=1002069 bytes_retransmit=0 bytes_invalid=0 send_seq=6414 receive_seq=6414 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998754 coil_temp=17.7 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.8 th1: temp=44.1 th2: temp=49.0 th3: temp=47.4 sysload=0.04 cputime=195.548 memavail=7399576 print_time=2227.143 buffer_time=2.355 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 15 Hz
Stats 2203.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18116624 bytes_read=2189760 bytes_retransmit=9 bytes_invalid=0 send_seq=313912 receive_seq=313912 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015970 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14074 bytes_read=45372 bytes_retransmit=0 bytes_invalid=0 send_seq=2317 receive_seq=2317 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999259 adj=49997341 toolboard_t0: mcu_awake=0.061 mcu_task_avg=0.000094 mcu_task_stddev=0.000074 bytes_write=90460 bytes_read=2729768 bytes_retransmit=9 bytes_invalid=0 send_seq=12071 receive_seq=12071 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997712 toolboard_t1: mcu_awake=0.155 mcu_task_avg=0.000111 mcu_task_stddev=0.000071 bytes_write=41230 bytes_read=642796 bytes_retransmit=9 bytes_invalid=0 send_seq=5125 receive_seq=5125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997615 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14287 bytes_read=559036 bytes_retransmit=9 bytes_invalid=0 send_seq=2327 receive_seq=2327 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997735 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14827 bytes_read=44501 bytes_retransmit=9 bytes_invalid=0 send_seq=2318 receive_seq=2318 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999455 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63399 bytes_read=1002425 bytes_retransmit=0 bytes_invalid=0 send_seq=6415 receive_seq=6415 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998719 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=45.0 th1: temp=44.1 th2: temp=48.9 th3: temp=47.3 sysload=0.04 cputime=195.617 memavail=7399576 print_time=2227.997 buffer_time=2.209 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 16 Hz
Stats 2204.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18118168 bytes_read=2190285 bytes_retransmit=9 bytes_invalid=0 send_seq=313955 receive_seq=313955 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015966 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14080 bytes_read=45388 bytes_retransmit=0 bytes_invalid=0 send_seq=2318 receive_seq=2318 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997282 toolboard_t0: mcu_awake=0.061 mcu_task_avg=0.000094 mcu_task_stddev=0.000074 bytes_write=90536 bytes_read=2732854 bytes_retransmit=9 bytes_invalid=0 send_seq=12082 receive_seq=12082 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997666 toolboard_t1: mcu_awake=0.155 mcu_task_avg=0.000111 mcu_task_stddev=0.000071 bytes_write=41236 bytes_read=642924 bytes_retransmit=9 bytes_invalid=0 send_seq=5126 receive_seq=5126 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997571 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14293 bytes_read=559330 bytes_retransmit=9 bytes_invalid=0 send_seq=2328 receive_seq=2328 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997692 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14833 bytes_read=44516 bytes_retransmit=9 bytes_invalid=0 send_seq=2319 receive_seq=2319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63405 bytes_read=1002781 bytes_retransmit=0 bytes_invalid=0 send_seq=6416 receive_seq=6416 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998680 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.6 th1: temp=44.1 th2: temp=48.9 th3: temp=47.2 sysload=0.04 cputime=195.690 memavail=7399576 print_time=2228.962 buffer_time=2.174 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2205.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18119423 bytes_read=2190829 bytes_retransmit=9 bytes_invalid=0 send_seq=313993 receive_seq=313993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016012 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14086 bytes_read=45404 bytes_retransmit=0 bytes_invalid=0 send_seq=2319 receive_seq=2319 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997269 toolboard_t0: mcu_awake=0.061 mcu_task_avg=0.000094 mcu_task_stddev=0.000074 bytes_write=90605 bytes_read=2735888 bytes_retransmit=9 bytes_invalid=0 send_seq=12092 receive_seq=12092 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997658 toolboard_t1: mcu_awake=0.155 mcu_task_avg=0.000111 mcu_task_stddev=0.000071 bytes_write=41242 bytes_read=643024 bytes_retransmit=9 bytes_invalid=0 send_seq=5127 receive_seq=5127 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14299 bytes_read=559579 bytes_retransmit=9 bytes_invalid=0 send_seq=2329 receive_seq=2329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14839 bytes_read=44531 bytes_retransmit=9 bytes_invalid=0 send_seq=2320 receive_seq=2320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63411 bytes_read=1003137 bytes_retransmit=0 bytes_invalid=0 send_seq=6417 receive_seq=6417 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998680 coil_temp=17.7 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=44.9 th1: temp=44.0 th2: temp=49.0 th3: temp=47.2 sysload=0.04 cputime=195.764 memavail=7399352 print_time=2229.843 buffer_time=2.054 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 17 Hz
Testing frequency 18 Hz
Stats 2206.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18121296 bytes_read=2191379 bytes_retransmit=9 bytes_invalid=0 send_seq=314041 receive_seq=314041 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=47 upcoming_bytes=0 freq=400015980 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14092 bytes_read=45420 bytes_retransmit=0 bytes_invalid=0 send_seq=2320 receive_seq=2320 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997195 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=90681 bytes_read=2738961 bytes_retransmit=9 bytes_invalid=0 send_seq=12103 receive_seq=12103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997548 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41248 bytes_read=643138 bytes_retransmit=9 bytes_invalid=0 send_seq=5128 receive_seq=5128 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997470 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14305 bytes_read=559813 bytes_retransmit=9 bytes_invalid=0 send_seq=2330 receive_seq=2330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997602 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14845 bytes_read=44546 bytes_retransmit=9 bytes_invalid=0 send_seq=2321 receive_seq=2321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999427 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63417 bytes_read=1003493 bytes_retransmit=0 bytes_invalid=0 send_seq=6418 receive_seq=6418 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998629 coil_temp=17.7 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.8 th1: temp=44.1 th2: temp=49.1 th3: temp=47.3 sysload=0.04 cputime=195.843 memavail=7398888 print_time=2231.112 buffer_time=2.322 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 19 Hz
Stats 2207.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18122878 bytes_read=2191909 bytes_retransmit=9 bytes_invalid=0 send_seq=314085 receive_seq=314085 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015954 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14098 bytes_read=45436 bytes_retransmit=0 bytes_invalid=0 send_seq=2321 receive_seq=2321 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997255 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=90757 bytes_read=2742049 bytes_retransmit=9 bytes_invalid=0 send_seq=12114 receive_seq=12114 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997619 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41254 bytes_read=643266 bytes_retransmit=9 bytes_invalid=0 send_seq=5129 receive_seq=5129 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14311 bytes_read=560107 bytes_retransmit=9 bytes_invalid=0 send_seq=2331 receive_seq=2331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14851 bytes_read=44572 bytes_retransmit=9 bytes_invalid=0 send_seq=2322 receive_seq=2322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63423 bytes_read=1003849 bytes_retransmit=0 bytes_invalid=0 send_seq=6419 receive_seq=6419 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998653 coil_temp=17.7 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.5 th1: temp=44.3 th2: temp=49.1 th3: temp=47.3 sysload=0.03 cputime=195.918 memavail=7398888 print_time=2231.932 buffer_time=2.142 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 20 Hz
Stats 2208.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18124439 bytes_read=2192458 bytes_retransmit=9 bytes_invalid=0 send_seq=314127 receive_seq=314127 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015922 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14104 bytes_read=45465 bytes_retransmit=0 bytes_invalid=0 send_seq=2322 receive_seq=2322 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997288 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=90833 bytes_read=2745107 bytes_retransmit=9 bytes_invalid=0 send_seq=12125 receive_seq=12125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997648 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41260 bytes_read=643366 bytes_retransmit=9 bytes_invalid=0 send_seq=5130 receive_seq=5130 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997556 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14317 bytes_read=560341 bytes_retransmit=9 bytes_invalid=0 send_seq=2332 receive_seq=2332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997710 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14857 bytes_read=44587 bytes_retransmit=9 bytes_invalid=0 send_seq=2323 receive_seq=2323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63429 bytes_read=1004223 bytes_retransmit=0 bytes_invalid=0 send_seq=6420 receive_seq=6420 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998668 coil_temp=17.7 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=44.4 th1: temp=44.1 th2: temp=49.6 th3: temp=47.5 sysload=0.03 cputime=195.993 memavail=7398888 print_time=2232.918 buffer_time=2.127 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 21 Hz
Stats 2209.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18126123 bytes_read=2192978 bytes_retransmit=9 bytes_invalid=0 send_seq=314169 receive_seq=314169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015917 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14110 bytes_read=45481 bytes_retransmit=0 bytes_invalid=0 send_seq=2323 receive_seq=2323 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997327 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=90909 bytes_read=2748164 bytes_retransmit=9 bytes_invalid=0 send_seq=12136 receive_seq=12136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997759 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41266 bytes_read=643466 bytes_retransmit=9 bytes_invalid=0 send_seq=5131 receive_seq=5131 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997596 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14323 bytes_read=560575 bytes_retransmit=9 bytes_invalid=0 send_seq=2333 receive_seq=2333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997747 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14863 bytes_read=44602 bytes_retransmit=9 bytes_invalid=0 send_seq=2324 receive_seq=2324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999459 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63435 bytes_read=1004579 bytes_retransmit=0 bytes_invalid=0 send_seq=6421 receive_seq=6421 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998698 coil_temp=17.7 refs=0 mcu_temp=20.76 supply_voltage=3.012 th0: temp=44.2 th1: temp=43.9 th2: temp=49.1 th3: temp=47.4 sysload=0.03 cputime=196.064 memavail=7398888 print_time=2233.789 buffer_time=1.997 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 22 Hz
Stats 2210.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18128130 bytes_read=2193538 bytes_retransmit=9 bytes_invalid=0 send_seq=314216 receive_seq=314216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=0 freq=400015897 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14116 bytes_read=45497 bytes_retransmit=0 bytes_invalid=0 send_seq=2324 receive_seq=2324 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997320 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=90985 bytes_read=2751308 bytes_retransmit=9 bytes_invalid=0 send_seq=12147 receive_seq=12147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997781 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41272 bytes_read=643594 bytes_retransmit=9 bytes_invalid=0 send_seq=5132 receive_seq=5132 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997592 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14329 bytes_read=560884 bytes_retransmit=9 bytes_invalid=0 send_seq=2334 receive_seq=2334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997735 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14869 bytes_read=44617 bytes_retransmit=9 bytes_invalid=0 send_seq=2325 receive_seq=2325 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999459 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63441 bytes_read=1004935 bytes_retransmit=0 bytes_invalid=0 send_seq=6422 receive_seq=6422 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998694 coil_temp=17.7 refs=0 mcu_temp=20.76 supply_voltage=3.012 th0: temp=44.3 th1: temp=43.7 th2: temp=49.0 th3: temp=47.4 sysload=0.03 cputime=196.143 memavail=7398888 print_time=2235.012 buffer_time=2.220 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 23 Hz
Stats 2211.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18129725 bytes_read=2194077 bytes_retransmit=9 bytes_invalid=0 send_seq=314257 receive_seq=314257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015883 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14122 bytes_read=45513 bytes_retransmit=0 bytes_invalid=0 send_seq=2325 receive_seq=2325 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997324 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=91061 bytes_read=2754382 bytes_retransmit=9 bytes_invalid=0 send_seq=12158 receive_seq=12158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997760 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=41278 bytes_read=643708 bytes_retransmit=9 bytes_invalid=0 send_seq=5133 receive_seq=5133 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997591 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14335 bytes_read=561118 bytes_retransmit=9 bytes_invalid=0 send_seq=2335 receive_seq=2335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997729 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14875 bytes_read=44632 bytes_retransmit=9 bytes_invalid=0 send_seq=2326 receive_seq=2326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999461 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63447 bytes_read=1005291 bytes_retransmit=0 bytes_invalid=0 send_seq=6423 receive_seq=6423 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998695 coil_temp=17.7 refs=0 mcu_temp=20.76 supply_voltage=3.012 th0: temp=44.2 th1: temp=43.7 th2: temp=49.1 th3: temp=47.3 sysload=0.03 cputime=196.218 memavail=7398888 print_time=2235.933 buffer_time=2.140 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2212.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18131574 bytes_read=2194617 bytes_retransmit=9 bytes_invalid=0 send_seq=314303 receive_seq=314303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015897 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14128 bytes_read=45529 bytes_retransmit=0 bytes_invalid=0 send_seq=2326 receive_seq=2326 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997339 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=91137 bytes_read=2757439 bytes_retransmit=9 bytes_invalid=0 send_seq=12169 receive_seq=12169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997832 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=41284 bytes_read=643808 bytes_retransmit=9 bytes_invalid=0 send_seq=5134 receive_seq=5134 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997601 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14341 bytes_read=561352 bytes_retransmit=9 bytes_invalid=0 send_seq=2336 receive_seq=2336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997731 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14881 bytes_read=44658 bytes_retransmit=9 bytes_invalid=0 send_seq=2327 receive_seq=2327 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999472 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63453 bytes_read=1005647 bytes_retransmit=0 bytes_invalid=0 send_seq=6424 receive_seq=6424 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998711 coil_temp=17.7 refs=0 mcu_temp=20.76 supply_voltage=3.012 th0: temp=44.2 th1: temp=44.0 th2: temp=49.1 th3: temp=47.4 sysload=0.11 cputime=196.291 memavail=7398888 print_time=2236.818 buffer_time=2.025 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 24 Hz
Testing frequency 25 Hz
Stats 2213.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18133271 bytes_read=2195147 bytes_retransmit=9 bytes_invalid=0 send_seq=314347 receive_seq=314347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015874 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14134 bytes_read=45558 bytes_retransmit=0 bytes_invalid=0 send_seq=2327 receive_seq=2327 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997307 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=91213 bytes_read=2760525 bytes_retransmit=9 bytes_invalid=0 send_seq=12180 receive_seq=12180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997761 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=41290 bytes_read=643936 bytes_retransmit=9 bytes_invalid=0 send_seq=5135 receive_seq=5135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997548 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14347 bytes_read=561630 bytes_retransmit=9 bytes_invalid=0 send_seq=2337 receive_seq=2337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14887 bytes_read=44674 bytes_retransmit=9 bytes_invalid=0 send_seq=2328 receive_seq=2328 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999463 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63459 bytes_read=1006003 bytes_retransmit=0 bytes_invalid=0 send_seq=6425 receive_seq=6425 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998685 coil_temp=17.7 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=44.0 th1: temp=43.7 th2: temp=49.0 th3: temp=47.5 sysload=0.11 cputime=196.369 memavail=7398924 print_time=2237.783 buffer_time=1.987 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Testing frequency 26 Hz
Stats 2214.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18135621 bytes_read=2195756 bytes_retransmit=9 bytes_invalid=0 send_seq=314401 receive_seq=314401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015853 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14140 bytes_read=45574 bytes_retransmit=0 bytes_invalid=0 send_seq=2328 receive_seq=2328 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997338 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=91289 bytes_read=2763581 bytes_retransmit=9 bytes_invalid=0 send_seq=12191 receive_seq=12191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997782 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=41296 bytes_read=644036 bytes_retransmit=9 bytes_invalid=0 send_seq=5136 receive_seq=5136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14353 bytes_read=561848 bytes_retransmit=9 bytes_invalid=0 send_seq=2338 receive_seq=2338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997710 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14893 bytes_read=44690 bytes_retransmit=9 bytes_invalid=0 send_seq=2329 receive_seq=2329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999467 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63465 bytes_read=1006359 bytes_retransmit=0 bytes_invalid=0 send_seq=6426 receive_seq=6426 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998695 coil_temp=17.7 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=43.8 th1: temp=44.3 th2: temp=49.2 th3: temp=47.5 sysload=0.11 cputime=196.449 memavail=7398924 print_time=2239.010 buffer_time=2.213 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2215.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18137369 bytes_read=2196296 bytes_retransmit=9 bytes_invalid=0 send_seq=314444 receive_seq=314444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015841 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14146 bytes_read=45590 bytes_retransmit=0 bytes_invalid=0 send_seq=2329 receive_seq=2329 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997347 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=91365 bytes_read=2766639 bytes_retransmit=9 bytes_invalid=0 send_seq=12202 receive_seq=12202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997767 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=41302 bytes_read=644136 bytes_retransmit=9 bytes_invalid=0 send_seq=5137 receive_seq=5137 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997602 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14359 bytes_read=562081 bytes_retransmit=9 bytes_invalid=0 send_seq=2339 receive_seq=2339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997732 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14899 bytes_read=44706 bytes_retransmit=9 bytes_invalid=0 send_seq=2330 receive_seq=2330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999467 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63471 bytes_read=1006715 bytes_retransmit=0 bytes_invalid=0 send_seq=6427 receive_seq=6427 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998696 coil_temp=17.7 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.7 th1: temp=44.0 th2: temp=49.4 th3: temp=47.5 sysload=0.11 cputime=196.523 memavail=7398932 print_time=2239.868 buffer_time=2.069 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 27 Hz
Stats 2216.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18139300 bytes_read=2196846 bytes_retransmit=9 bytes_invalid=0 send_seq=314492 receive_seq=314492 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015820 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14152 bytes_read=45606 bytes_retransmit=0 bytes_invalid=0 send_seq=2330 receive_seq=2330 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997372 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=91441 bytes_read=2769800 bytes_retransmit=9 bytes_invalid=0 send_seq=12213 receive_seq=12213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997831 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41308 bytes_read=644278 bytes_retransmit=9 bytes_invalid=0 send_seq=5138 receive_seq=5138 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997623 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14365 bytes_read=562355 bytes_retransmit=9 bytes_invalid=0 send_seq=2340 receive_seq=2340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997739 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14905 bytes_read=44722 bytes_retransmit=9 bytes_invalid=0 send_seq=2331 receive_seq=2331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999471 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63477 bytes_read=1007071 bytes_retransmit=0 bytes_invalid=0 send_seq=6428 receive_seq=6428 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998707 coil_temp=17.7 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=44.1 th1: temp=43.7 th2: temp=49.5 th3: temp=47.6 sysload=0.11 cputime=196.600 memavail=7398196 print_time=2240.844 buffer_time=2.042 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 28 Hz
Testing frequency 29 Hz
Stats 2217.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18141497 bytes_read=2197455 bytes_retransmit=9 bytes_invalid=0 send_seq=314546 receive_seq=314546 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=0 freq=400015827 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14158 bytes_read=45622 bytes_retransmit=0 bytes_invalid=0 send_seq=2331 receive_seq=2331 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997377 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=91517 bytes_read=2772858 bytes_retransmit=9 bytes_invalid=0 send_seq=12224 receive_seq=12224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997830 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41314 bytes_read=644378 bytes_retransmit=9 bytes_invalid=0 send_seq=5139 receive_seq=5139 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997634 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14371 bytes_read=562573 bytes_retransmit=9 bytes_invalid=0 send_seq=2341 receive_seq=2341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997752 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14911 bytes_read=44749 bytes_retransmit=9 bytes_invalid=0 send_seq=2332 receive_seq=2332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999473 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63483 bytes_read=1007427 bytes_retransmit=0 bytes_invalid=0 send_seq=6429 receive_seq=6429 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998719 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.9 th1: temp=43.8 th2: temp=48.7 th3: temp=47.6 sysload=0.10 cputime=196.681 memavail=7397336 print_time=2242.019 buffer_time=2.214 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 30 Hz
Stats 2218.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18143370 bytes_read=2198000 bytes_retransmit=9 bytes_invalid=0 send_seq=314593 receive_seq=314593 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015807 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14164 bytes_read=45651 bytes_retransmit=0 bytes_invalid=0 send_seq=2332 receive_seq=2332 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997324 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=91593 bytes_read=2775915 bytes_retransmit=9 bytes_invalid=0 send_seq=12235 receive_seq=12235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997767 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41320 bytes_read=644478 bytes_retransmit=9 bytes_invalid=0 send_seq=5140 receive_seq=5140 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997577 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14377 bytes_read=562791 bytes_retransmit=9 bytes_invalid=0 send_seq=2342 receive_seq=2342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997711 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14917 bytes_read=44765 bytes_retransmit=9 bytes_invalid=0 send_seq=2333 receive_seq=2333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999461 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63489 bytes_read=1007783 bytes_retransmit=0 bytes_invalid=0 send_seq=6430 receive_seq=6430 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998693 coil_temp=17.7 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.7 th1: temp=43.6 th2: temp=49.1 th3: temp=47.5 sysload=0.10 cputime=196.762 memavail=7398312 print_time=2242.900 buffer_time=2.093 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2219.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18145444 bytes_read=2198565 bytes_retransmit=9 bytes_invalid=0 send_seq=314644 receive_seq=314644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015812 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14170 bytes_read=45667 bytes_retransmit=0 bytes_invalid=0 send_seq=2333 receive_seq=2333 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997351 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=91669 bytes_read=2779000 bytes_retransmit=9 bytes_invalid=0 send_seq=12246 receive_seq=12246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997784 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41326 bytes_read=644606 bytes_retransmit=9 bytes_invalid=0 send_seq=5141 receive_seq=5141 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997603 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14383 bytes_read=563085 bytes_retransmit=9 bytes_invalid=0 send_seq=2343 receive_seq=2343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997725 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14923 bytes_read=44781 bytes_retransmit=9 bytes_invalid=0 send_seq=2334 receive_seq=2334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999468 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63495 bytes_read=1008139 bytes_retransmit=0 bytes_invalid=0 send_seq=6431 receive_seq=6431 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998721 coil_temp=17.7 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=44.0 th1: temp=44.0 th2: temp=49.2 th3: temp=47.6 sysload=0.10 cputime=196.837 memavail=7398312 print_time=2243.860 buffer_time=2.051 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 31 Hz
Testing frequency 32 Hz
Stats 2220.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18147818 bytes_read=2199199 bytes_retransmit=9 bytes_invalid=0 send_seq=314700 receive_seq=314700 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=35 upcoming_bytes=0 freq=400015790 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14176 bytes_read=45683 bytes_retransmit=0 bytes_invalid=0 send_seq=2334 receive_seq=2334 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997334 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=91745 bytes_read=2782114 bytes_retransmit=9 bytes_invalid=0 send_seq=12257 receive_seq=12257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997807 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41332 bytes_read=644706 bytes_retransmit=9 bytes_invalid=0 send_seq=5142 receive_seq=5142 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997581 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14389 bytes_read=563334 bytes_retransmit=9 bytes_invalid=0 send_seq=2344 receive_seq=2344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997708 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14929 bytes_read=44797 bytes_retransmit=9 bytes_invalid=0 send_seq=2335 receive_seq=2335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999465 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63501 bytes_read=1008495 bytes_retransmit=0 bytes_invalid=0 send_seq=6432 receive_seq=6432 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998698 coil_temp=17.7 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=43.7 th1: temp=44.0 th2: temp=49.2 th3: temp=47.6 sysload=0.10 cputime=196.919 memavail=7398312 print_time=2245.042 buffer_time=2.230 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 33 Hz
Stats 2221.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18149696 bytes_read=2199744 bytes_retransmit=9 bytes_invalid=0 send_seq=314747 receive_seq=314747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015778 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14182 bytes_read=45699 bytes_retransmit=0 bytes_invalid=0 send_seq=2335 receive_seq=2335 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997352 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=91821 bytes_read=2785187 bytes_retransmit=9 bytes_invalid=0 send_seq=12268 receive_seq=12268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997805 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41338 bytes_read=644820 bytes_retransmit=9 bytes_invalid=0 send_seq=5143 receive_seq=5143 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997596 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14395 bytes_read=563568 bytes_retransmit=9 bytes_invalid=0 send_seq=2345 receive_seq=2345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997714 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14935 bytes_read=44813 bytes_retransmit=9 bytes_invalid=0 send_seq=2336 receive_seq=2336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999468 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63507 bytes_read=1008851 bytes_retransmit=0 bytes_invalid=0 send_seq=6433 receive_seq=6433 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998703 coil_temp=17.7 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.6 th1: temp=44.2 th2: temp=49.2 th3: temp=47.5 sysload=0.10 cputime=196.995 memavail=7398312 print_time=2245.940 buffer_time=2.127 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 2222.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18151905 bytes_read=2200314 bytes_retransmit=9 bytes_invalid=0 send_seq=314800 receive_seq=314800 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015777 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14188 bytes_read=45715 bytes_retransmit=0 bytes_invalid=0 send_seq=2336 receive_seq=2336 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997355 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=91897 bytes_read=2788272 bytes_retransmit=9 bytes_invalid=0 send_seq=12279 receive_seq=12279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997790 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41344 bytes_read=644948 bytes_retransmit=9 bytes_invalid=0 send_seq=5144 receive_seq=5144 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997608 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14401 bytes_read=563862 bytes_retransmit=9 bytes_invalid=0 send_seq=2346 receive_seq=2346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997789 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14941 bytes_read=44840 bytes_retransmit=9 bytes_invalid=0 send_seq=2337 receive_seq=2337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999468 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63513 bytes_read=1009207 bytes_retransmit=0 bytes_invalid=0 send_seq=6434 receive_seq=6434 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998703 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.6 th1: temp=44.0 th2: temp=49.3 th3: temp=47.6 sysload=0.09 cputime=197.070 memavail=7398312 print_time=2246.881 buffer_time=2.066 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 34 Hz
Testing frequency 35 Hz
Stats 2223.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18154540 bytes_read=2200948 bytes_retransmit=9 bytes_invalid=0 send_seq=314859 receive_seq=314859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015774 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14194 bytes_read=45744 bytes_retransmit=0 bytes_invalid=0 send_seq=2337 receive_seq=2337 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997343 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=91973 bytes_read=2791331 bytes_retransmit=9 bytes_invalid=0 send_seq=12290 receive_seq=12290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997780 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41350 bytes_read=645048 bytes_retransmit=9 bytes_invalid=0 send_seq=5145 receive_seq=5145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997592 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14407 bytes_read=564096 bytes_retransmit=9 bytes_invalid=0 send_seq=2347 receive_seq=2347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997762 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14947 bytes_read=44856 bytes_retransmit=9 bytes_invalid=0 send_seq=2338 receive_seq=2338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999464 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63519 bytes_read=1009563 bytes_retransmit=0 bytes_invalid=0 send_seq=6435 receive_seq=6435 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998692 coil_temp=17.7 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.4 th1: temp=44.0 th2: temp=48.9 th3: temp=47.7 sysload=0.09 cputime=197.154 memavail=7398312 print_time=2248.090 buffer_time=2.272 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Testing frequency 36 Hz
Stats 2224.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18156374 bytes_read=2201493 bytes_retransmit=9 bytes_invalid=0 send_seq=314906 receive_seq=314906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015764 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14200 bytes_read=45760 bytes_retransmit=0 bytes_invalid=0 send_seq=2338 receive_seq=2338 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997320 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=92042 bytes_read=2794366 bytes_retransmit=9 bytes_invalid=0 send_seq=12300 receive_seq=12300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997734 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41356 bytes_read=645148 bytes_retransmit=9 bytes_invalid=0 send_seq=5146 receive_seq=5146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997585 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14413 bytes_read=564330 bytes_retransmit=9 bytes_invalid=0 send_seq=2348 receive_seq=2348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997730 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14953 bytes_read=44872 bytes_retransmit=9 bytes_invalid=0 send_seq=2339 receive_seq=2339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999459 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63525 bytes_read=1009919 bytes_retransmit=0 bytes_invalid=0 send_seq=6436 receive_seq=6436 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998681 coil_temp=17.7 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.4 th1: temp=44.0 th2: temp=49.1 th3: temp=47.6 sysload=0.09 cputime=197.230 memavail=7398312 print_time=2248.967 buffer_time=2.146 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2225.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18158749 bytes_read=2202098 bytes_retransmit=9 bytes_invalid=0 send_seq=314962 receive_seq=314962 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015771 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14206 bytes_read=45776 bytes_retransmit=0 bytes_invalid=0 send_seq=2339 receive_seq=2339 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997340 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=92118 bytes_read=2797510 bytes_retransmit=9 bytes_invalid=0 send_seq=12311 receive_seq=12311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997773 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41362 bytes_read=645276 bytes_retransmit=9 bytes_invalid=0 send_seq=5147 receive_seq=5147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997592 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14419 bytes_read=564639 bytes_retransmit=9 bytes_invalid=0 send_seq=2349 receive_seq=2349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997726 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14959 bytes_read=44888 bytes_retransmit=9 bytes_invalid=0 send_seq=2340 receive_seq=2340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999463 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63531 bytes_read=1010275 bytes_retransmit=0 bytes_invalid=0 send_seq=6437 receive_seq=6437 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998690 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.2 th2: temp=49.3 th3: temp=47.6 sysload=0.09 cputime=197.307 memavail=7398312 print_time=2249.919 buffer_time=2.094 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 37 Hz
Testing frequency 38 Hz
Stats 2226.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18161456 bytes_read=2202747 bytes_retransmit=9 bytes_invalid=0 send_seq=315024 receive_seq=315024 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015773 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14212 bytes_read=45792 bytes_retransmit=0 bytes_invalid=0 send_seq=2340 receive_seq=2340 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997323 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=92194 bytes_read=2800585 bytes_retransmit=9 bytes_invalid=0 send_seq=12322 receive_seq=12322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997724 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41368 bytes_read=645376 bytes_retransmit=9 bytes_invalid=0 send_seq=5148 receive_seq=5148 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997560 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14425 bytes_read=564873 bytes_retransmit=9 bytes_invalid=0 send_seq=2350 receive_seq=2350 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997702 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14965 bytes_read=44904 bytes_retransmit=9 bytes_invalid=0 send_seq=2341 receive_seq=2341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63537 bytes_read=1010631 bytes_retransmit=0 bytes_invalid=0 send_seq=6438 receive_seq=6438 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998674 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.4 th1: temp=44.0 th2: temp=49.3 th3: temp=47.7 sysload=0.09 cputime=197.391 memavail=7397868 print_time=2251.103 buffer_time=2.276 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 39 Hz
Stats 2227.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18163349 bytes_read=2203302 bytes_retransmit=9 bytes_invalid=0 send_seq=315073 receive_seq=315073 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015768 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14218 bytes_read=45808 bytes_retransmit=0 bytes_invalid=0 send_seq=2341 receive_seq=2341 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997317 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=92270 bytes_read=2803644 bytes_retransmit=9 bytes_invalid=0 send_seq=12333 receive_seq=12333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997686 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41374 bytes_read=645490 bytes_retransmit=9 bytes_invalid=0 send_seq=5149 receive_seq=5149 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997540 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14431 bytes_read=565107 bytes_retransmit=9 bytes_invalid=0 send_seq=2351 receive_seq=2351 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14971 bytes_read=44931 bytes_retransmit=9 bytes_invalid=0 send_seq=2342 receive_seq=2342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999454 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63543 bytes_read=1010987 bytes_retransmit=0 bytes_invalid=0 send_seq=6439 receive_seq=6439 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998663 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.6 th1: temp=44.0 th2: temp=49.4 th3: temp=47.6 sysload=0.08 cputime=197.468 memavail=7397868 print_time=2251.990 buffer_time=2.160 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 40 Hz
Stats 2228.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18165855 bytes_read=2203902 bytes_retransmit=9 bytes_invalid=0 send_seq=315131 receive_seq=315131 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015779 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=14224 bytes_read=45837 bytes_retransmit=0 bytes_invalid=0 send_seq=2342 receive_seq=2342 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997330 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=92346 bytes_read=2806730 bytes_retransmit=9 bytes_invalid=0 send_seq=12344 receive_seq=12344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997674 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41380 bytes_read=645618 bytes_retransmit=9 bytes_invalid=0 send_seq=5150 receive_seq=5150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997544 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14437 bytes_read=565401 bytes_retransmit=9 bytes_invalid=0 send_seq=2352 receive_seq=2352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14977 bytes_read=44947 bytes_retransmit=9 bytes_invalid=0 send_seq=2343 receive_seq=2343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999453 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63549 bytes_read=1011343 bytes_retransmit=0 bytes_invalid=0 send_seq=6440 receive_seq=6440 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998669 coil_temp=17.7 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.5 th1: temp=43.9 th2: temp=49.3 th3: temp=47.6 sysload=0.08 cputime=197.546 memavail=7397868 print_time=2252.945 buffer_time=2.114 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 41 Hz
Stats 2229.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18167813 bytes_read=2204481 bytes_retransmit=9 bytes_invalid=0 send_seq=315179 receive_seq=315179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015785 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=14230 bytes_read=45853 bytes_retransmit=0 bytes_invalid=0 send_seq=2343 receive_seq=2343 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997305 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=92422 bytes_read=2809846 bytes_retransmit=9 bytes_invalid=0 send_seq=12355 receive_seq=12355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997783 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41386 bytes_read=645718 bytes_retransmit=9 bytes_invalid=0 send_seq=5151 receive_seq=5151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997521 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14443 bytes_read=565635 bytes_retransmit=9 bytes_invalid=0 send_seq=2353 receive_seq=2353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14983 bytes_read=44963 bytes_retransmit=9 bytes_invalid=0 send_seq=2344 receive_seq=2344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63555 bytes_read=1011699 bytes_retransmit=0 bytes_invalid=0 send_seq=6441 receive_seq=6441 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998655 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.3 th2: temp=49.4 th3: temp=47.6 sysload=0.08 cputime=197.626 memavail=7397868 print_time=2253.823 buffer_time=1.989 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 42 Hz
Stats 2230.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18170734 bytes_read=2205131 bytes_retransmit=9 bytes_invalid=0 send_seq=315244 receive_seq=315244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=400015789 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=14236 bytes_read=45869 bytes_retransmit=0 bytes_invalid=0 send_seq=2344 receive_seq=2344 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997298 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=92498 bytes_read=2812903 bytes_retransmit=9 bytes_invalid=0 send_seq=12366 receive_seq=12366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997736 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41392 bytes_read=645818 bytes_retransmit=9 bytes_invalid=0 send_seq=5152 receive_seq=5152 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14449 bytes_read=565884 bytes_retransmit=9 bytes_invalid=0 send_seq=2354 receive_seq=2354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14989 bytes_read=44979 bytes_retransmit=9 bytes_invalid=0 send_seq=2345 receive_seq=2345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63561 bytes_read=1012055 bytes_retransmit=0 bytes_invalid=0 send_seq=6442 receive_seq=6442 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998655 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.1 th2: temp=49.4 th3: temp=47.8 sysload=0.08 cputime=197.712 memavail=7397868 print_time=2255.033 buffer_time=2.197 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 43 Hz
Stats 2231.3: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18173348 bytes_read=2205736 bytes_retransmit=9 bytes_invalid=0 send_seq=315303 receive_seq=315303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015817 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=14242 bytes_read=45885 bytes_retransmit=0 bytes_invalid=0 send_seq=2345 receive_seq=2345 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997294 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=92574 bytes_read=2816006 bytes_retransmit=9 bytes_invalid=0 send_seq=12377 receive_seq=12377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997692 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41398 bytes_read=645946 bytes_retransmit=9 bytes_invalid=0 send_seq=5153 receive_seq=5153 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997542 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14455 bytes_read=566178 bytes_retransmit=9 bytes_invalid=0 send_seq=2355 receive_seq=2355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=14995 bytes_read=44995 bytes_retransmit=9 bytes_invalid=0 send_seq=2346 receive_seq=2346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63567 bytes_read=1012411 bytes_retransmit=0 bytes_invalid=0 send_seq=6443 receive_seq=6443 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998647 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.4 th1: temp=44.1 th2: temp=49.1 th3: temp=47.7 sysload=0.08 cputime=197.792 memavail=7397868 print_time=2255.950 buffer_time=2.112 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2232.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18175386 bytes_read=2206321 bytes_retransmit=9 bytes_invalid=0 send_seq=315353 receive_seq=315353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015825 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=14248 bytes_read=45901 bytes_retransmit=0 bytes_invalid=0 send_seq=2346 receive_seq=2346 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997248 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=92650 bytes_read=2819063 bytes_retransmit=9 bytes_invalid=0 send_seq=12388 receive_seq=12388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997709 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41404 bytes_read=646060 bytes_retransmit=9 bytes_invalid=0 send_seq=5154 receive_seq=5154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997479 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14461 bytes_read=566412 bytes_retransmit=9 bytes_invalid=0 send_seq=2356 receive_seq=2356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997595 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15001 bytes_read=45022 bytes_retransmit=9 bytes_invalid=0 send_seq=2347 receive_seq=2347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63573 bytes_read=1012767 bytes_retransmit=0 bytes_invalid=0 send_seq=6444 receive_seq=6444 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998632 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.1 th2: temp=49.4 th3: temp=47.8 sysload=0.08 cputime=197.869 memavail=7398016 print_time=2256.853 buffer_time=2.012 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 44 Hz
Testing frequency 45 Hz
Stats 2233.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18178354 bytes_read=2206958 bytes_retransmit=9 bytes_invalid=0 send_seq=315419 receive_seq=315419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=0 freq=400015823 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14254 bytes_read=45930 bytes_retransmit=0 bytes_invalid=0 send_seq=2347 receive_seq=2347 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997256 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=92726 bytes_read=2822119 bytes_retransmit=9 bytes_invalid=0 send_seq=12399 receive_seq=12399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997658 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41410 bytes_read=646160 bytes_retransmit=9 bytes_invalid=0 send_seq=5155 receive_seq=5155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997457 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14467 bytes_read=566646 bytes_retransmit=9 bytes_invalid=0 send_seq=2357 receive_seq=2357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997586 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15007 bytes_read=45038 bytes_retransmit=9 bytes_invalid=0 send_seq=2348 receive_seq=2348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999432 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63579 bytes_read=1013123 bytes_retransmit=0 bytes_invalid=0 send_seq=6445 receive_seq=6445 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998635 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.4 th1: temp=44.1 th2: temp=49.5 th3: temp=47.6 sysload=0.08 cputime=197.956 memavail=7398152 print_time=2258.049 buffer_time=2.206 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 46 Hz
Stats 2234.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18181078 bytes_read=2207573 bytes_retransmit=9 bytes_invalid=0 send_seq=315480 receive_seq=315480 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015831 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14260 bytes_read=45946 bytes_retransmit=0 bytes_invalid=0 send_seq=2348 receive_seq=2348 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997271 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=92802 bytes_read=2825262 bytes_retransmit=9 bytes_invalid=0 send_seq=12410 receive_seq=12410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997646 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41416 bytes_read=646288 bytes_retransmit=9 bytes_invalid=0 send_seq=5156 receive_seq=5156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997468 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14473 bytes_read=566940 bytes_retransmit=9 bytes_invalid=0 send_seq=2358 receive_seq=2358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997602 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15013 bytes_read=45054 bytes_retransmit=9 bytes_invalid=0 send_seq=2349 receive_seq=2349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63585 bytes_read=1013479 bytes_retransmit=0 bytes_invalid=0 send_seq=6446 receive_seq=6446 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998653 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.0 th1: temp=44.1 th2: temp=49.5 th3: temp=47.7 sysload=0.08 cputime=198.038 memavail=7398152 print_time=2258.970 buffer_time=2.124 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2235.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18183140 bytes_read=2208182 bytes_retransmit=9 bytes_invalid=0 send_seq=315531 receive_seq=315531 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015887 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14266 bytes_read=45962 bytes_retransmit=0 bytes_invalid=0 send_seq=2349 receive_seq=2349 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997249 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=92878 bytes_read=2828318 bytes_retransmit=9 bytes_invalid=0 send_seq=12421 receive_seq=12421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997625 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41422 bytes_read=646388 bytes_retransmit=9 bytes_invalid=0 send_seq=5157 receive_seq=5157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997459 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14479 bytes_read=567189 bytes_retransmit=9 bytes_invalid=0 send_seq=2359 receive_seq=2359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997591 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15019 bytes_read=45070 bytes_retransmit=9 bytes_invalid=0 send_seq=2350 receive_seq=2350 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999432 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63591 bytes_read=1013835 bytes_retransmit=0 bytes_invalid=0 send_seq=6447 receive_seq=6447 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998667 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.2 th2: temp=49.3 th3: temp=47.6 sysload=0.08 cputime=198.127 memavail=7397492 print_time=2259.858 buffer_time=2.011 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 47 Hz
Testing frequency 48 Hz
Stats 2236.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18186146 bytes_read=2208822 bytes_retransmit=9 bytes_invalid=0 send_seq=315597 receive_seq=315597 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=47 upcoming_bytes=0 freq=400015885 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14272 bytes_read=45978 bytes_retransmit=0 bytes_invalid=0 send_seq=2350 receive_seq=2350 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997159 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=92954 bytes_read=2831407 bytes_retransmit=9 bytes_invalid=0 send_seq=12432 receive_seq=12432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997493 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41428 bytes_read=646488 bytes_retransmit=9 bytes_invalid=0 send_seq=5158 receive_seq=5158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997344 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14485 bytes_read=567438 bytes_retransmit=9 bytes_invalid=0 send_seq=2360 receive_seq=2360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997504 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15025 bytes_read=45086 bytes_retransmit=9 bytes_invalid=0 send_seq=2351 receive_seq=2351 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999411 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63597 bytes_read=1014191 bytes_retransmit=0 bytes_invalid=0 send_seq=6448 receive_seq=6448 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998609 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.2 th2: temp=49.3 th3: temp=47.9 sysload=0.08 cputime=198.219 memavail=7397496 print_time=2261.067 buffer_time=2.218 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 49 Hz
Stats 2237.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18188933 bytes_read=2209441 bytes_retransmit=9 bytes_invalid=0 send_seq=315656 receive_seq=315656 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015879 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14278 bytes_read=45994 bytes_retransmit=0 bytes_invalid=0 send_seq=2351 receive_seq=2351 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999261 adj=49997191 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=93030 bytes_read=2834477 bytes_retransmit=9 bytes_invalid=0 send_seq=12443 receive_seq=12443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997529 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41434 bytes_read=646630 bytes_retransmit=9 bytes_invalid=0 send_seq=5159 receive_seq=5159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997395 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14491 bytes_read=567717 bytes_retransmit=9 bytes_invalid=0 send_seq=2361 receive_seq=2361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997547 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15031 bytes_read=45113 bytes_retransmit=9 bytes_invalid=0 send_seq=2352 receive_seq=2352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999420 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63603 bytes_read=1014547 bytes_retransmit=0 bytes_invalid=0 send_seq=6449 receive_seq=6449 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998617 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.7 th1: temp=44.0 th2: temp=49.3 th3: temp=47.5 sysload=0.07 cputime=198.304 memavail=7397272 print_time=2261.988 buffer_time=2.137 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2238.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18191070 bytes_read=2210021 bytes_retransmit=9 bytes_invalid=0 send_seq=315707 receive_seq=315707 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015873 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14284 bytes_read=46023 bytes_retransmit=0 bytes_invalid=0 send_seq=2352 receive_seq=2352 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999260 adj=49997265 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=93106 bytes_read=2837591 bytes_retransmit=9 bytes_invalid=0 send_seq=12454 receive_seq=12454 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997661 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41440 bytes_read=646730 bytes_retransmit=9 bytes_invalid=0 send_seq=5160 receive_seq=5160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997416 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14497 bytes_read=567951 bytes_retransmit=9 bytes_invalid=0 send_seq=2362 receive_seq=2362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997570 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15037 bytes_read=45129 bytes_retransmit=9 bytes_invalid=0 send_seq=2353 receive_seq=2353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999428 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63609 bytes_read=1014903 bytes_retransmit=0 bytes_invalid=0 send_seq=6450 receive_seq=6450 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998620 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.1 th2: temp=49.5 th3: temp=47.7 sysload=0.07 cputime=198.388 memavail=7397272 print_time=2262.887 buffer_time=2.030 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 50 Hz
Testing frequency 51 Hz
Stats 2239.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18194150 bytes_read=2210666 bytes_retransmit=9 bytes_invalid=0 send_seq=315774 receive_seq=315774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=0 freq=400015865 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14290 bytes_read=46039 bytes_retransmit=0 bytes_invalid=0 send_seq=2353 receive_seq=2353 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999259 adj=49997272 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=93182 bytes_read=2840663 bytes_retransmit=9 bytes_invalid=0 send_seq=12465 receive_seq=12465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997664 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41446 bytes_read=646844 bytes_retransmit=9 bytes_invalid=0 send_seq=5161 receive_seq=5161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997436 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14503 bytes_read=568215 bytes_retransmit=9 bytes_invalid=0 send_seq=2363 receive_seq=2363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15043 bytes_read=45145 bytes_retransmit=9 bytes_invalid=0 send_seq=2354 receive_seq=2354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999432 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63615 bytes_read=1015249 bytes_retransmit=0 bytes_invalid=0 send_seq=6451 receive_seq=6451 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998630 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.1 th1: temp=44.0 th2: temp=49.3 th3: temp=47.6 sysload=0.07 cputime=198.477 memavail=7397272 print_time=2264.079 buffer_time=2.221 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 52 Hz
Stats 2240.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18196967 bytes_read=2211330 bytes_retransmit=9 bytes_invalid=0 send_seq=315836 receive_seq=315836 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015879 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14296 bytes_read=46055 bytes_retransmit=0 bytes_invalid=0 send_seq=2354 receive_seq=2354 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997270 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=93258 bytes_read=2843734 bytes_retransmit=9 bytes_invalid=0 send_seq=12476 receive_seq=12476 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997655 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41452 bytes_read=646958 bytes_retransmit=9 bytes_invalid=0 send_seq=5162 receive_seq=5162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997464 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14509 bytes_read=568494 bytes_retransmit=9 bytes_invalid=0 send_seq=2364 receive_seq=2364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15049 bytes_read=45161 bytes_retransmit=9 bytes_invalid=0 send_seq=2355 receive_seq=2355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63621 bytes_read=1015594 bytes_retransmit=0 bytes_invalid=0 send_seq=6452 receive_seq=6452 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998662 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.4 th1: temp=44.2 th2: temp=49.5 th3: temp=47.7 sysload=0.07 cputime=198.559 memavail=7397288 print_time=2264.994 buffer_time=2.135 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2241.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18199163 bytes_read=2211905 bytes_retransmit=9 bytes_invalid=0 send_seq=315889 receive_seq=315889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015876 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14302 bytes_read=46071 bytes_retransmit=0 bytes_invalid=0 send_seq=2355 receive_seq=2355 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997242 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=93334 bytes_read=2846812 bytes_retransmit=9 bytes_invalid=0 send_seq=12487 receive_seq=12487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997697 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41458 bytes_read=647058 bytes_retransmit=9 bytes_invalid=0 send_seq=5163 receive_seq=5163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997447 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14515 bytes_read=568728 bytes_retransmit=9 bytes_invalid=0 send_seq=2365 receive_seq=2365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15055 bytes_read=45177 bytes_retransmit=9 bytes_invalid=0 send_seq=2356 receive_seq=2356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63627 bytes_read=1015938 bytes_retransmit=0 bytes_invalid=0 send_seq=6453 receive_seq=6453 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998645 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.3 th1: temp=44.2 th2: temp=49.4 th3: temp=47.8 sysload=0.07 cputime=198.639 memavail=7397288 print_time=2265.894 buffer_time=2.032 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 53 Hz
Testing frequency 54 Hz
Stats 2242.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18202415 bytes_read=2212565 bytes_retransmit=9 bytes_invalid=0 send_seq=315959 receive_seq=315959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015876 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14308 bytes_read=46086 bytes_retransmit=0 bytes_invalid=0 send_seq=2356 receive_seq=2356 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997244 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=93410 bytes_read=2849883 bytes_retransmit=9 bytes_invalid=0 send_seq=12498 receive_seq=12498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997666 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41464 bytes_read=647186 bytes_retransmit=9 bytes_invalid=0 send_seq=5164 receive_seq=5164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997469 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14521 bytes_read=569007 bytes_retransmit=9 bytes_invalid=0 send_seq=2366 receive_seq=2366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15061 bytes_read=45204 bytes_retransmit=9 bytes_invalid=0 send_seq=2357 receive_seq=2357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63633 bytes_read=1016283 bytes_retransmit=0 bytes_invalid=0 send_seq=6454 receive_seq=6454 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998652 coil_temp=17.6 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=43.4 th1: temp=44.3 th2: temp=49.4 th3: temp=47.6 sysload=0.07 cputime=198.731 memavail=7397288 print_time=2267.103 buffer_time=2.237 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 55 Hz
Stats 2243.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18205267 bytes_read=2213210 bytes_retransmit=9 bytes_invalid=0 send_seq=316021 receive_seq=316021 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015875 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14314 bytes_read=46114 bytes_retransmit=0 bytes_invalid=0 send_seq=2357 receive_seq=2357 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997240 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=93486 bytes_read=2853012 bytes_retransmit=9 bytes_invalid=0 send_seq=12509 receive_seq=12509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997653 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41470 bytes_read=647300 bytes_retransmit=9 bytes_invalid=0 send_seq=5165 receive_seq=5165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997474 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14527 bytes_read=569256 bytes_retransmit=9 bytes_invalid=0 send_seq=2367 receive_seq=2367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15067 bytes_read=45220 bytes_retransmit=9 bytes_invalid=0 send_seq=2358 receive_seq=2358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63639 bytes_read=1016628 bytes_retransmit=0 bytes_invalid=0 send_seq=6455 receive_seq=6455 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998653 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.3 th2: temp=49.4 th3: temp=48.1 sysload=0.07 cputime=198.814 memavail=7397288 print_time=2268.004 buffer_time=2.137 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 2244.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18207580 bytes_read=2213785 bytes_retransmit=9 bytes_invalid=0 send_seq=316074 receive_seq=316074 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015886 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14320 bytes_read=46129 bytes_retransmit=0 bytes_invalid=0 send_seq=2358 receive_seq=2358 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997245 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=93562 bytes_read=2856070 bytes_retransmit=9 bytes_invalid=0 send_seq=12520 receive_seq=12520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997628 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41476 bytes_read=647400 bytes_retransmit=9 bytes_invalid=0 send_seq=5166 receive_seq=5166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997477 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14533 bytes_read=569490 bytes_retransmit=9 bytes_invalid=0 send_seq=2368 receive_seq=2368 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15073 bytes_read=45236 bytes_retransmit=9 bytes_invalid=0 send_seq=2359 receive_seq=2359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63645 bytes_read=1016973 bytes_retransmit=0 bytes_invalid=0 send_seq=6456 receive_seq=6456 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998676 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.3 th2: temp=49.4 th3: temp=47.9 sysload=0.07 cputime=198.892 memavail=7397288 print_time=2268.923 buffer_time=2.054 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 56 Hz
Testing frequency 57 Hz
Stats 2245.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18210891 bytes_read=2214465 bytes_retransmit=9 bytes_invalid=0 send_seq=316145 receive_seq=316145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=0 freq=400015877 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14326 bytes_read=46144 bytes_retransmit=0 bytes_invalid=0 send_seq=2359 receive_seq=2359 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997228 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=93631 bytes_read=2859133 bytes_retransmit=9 bytes_invalid=0 send_seq=12530 receive_seq=12530 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997588 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41482 bytes_read=647514 bytes_retransmit=9 bytes_invalid=0 send_seq=5167 receive_seq=5167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997458 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14539 bytes_read=569784 bytes_retransmit=9 bytes_invalid=0 send_seq=2369 receive_seq=2369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15079 bytes_read=45252 bytes_retransmit=9 bytes_invalid=0 send_seq=2360 receive_seq=2360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63651 bytes_read=1017318 bytes_retransmit=0 bytes_invalid=0 send_seq=6457 receive_seq=6457 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998658 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.7 th1: temp=44.1 th2: temp=49.5 th3: temp=47.9 sysload=0.07 cputime=198.983 memavail=7397040 print_time=2270.128 buffer_time=2.259 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 58 Hz
Stats 2246.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18213803 bytes_read=2215114 bytes_retransmit=9 bytes_invalid=0 send_seq=316207 receive_seq=316207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015878 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14332 bytes_read=46159 bytes_retransmit=0 bytes_invalid=0 send_seq=2360 receive_seq=2360 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997249 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=93707 bytes_read=2862206 bytes_retransmit=9 bytes_invalid=0 send_seq=12541 receive_seq=12541 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997658 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41488 bytes_read=647628 bytes_retransmit=9 bytes_invalid=0 send_seq=5168 receive_seq=5168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14545 bytes_read=570033 bytes_retransmit=9 bytes_invalid=0 send_seq=2370 receive_seq=2370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997634 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15085 bytes_read=45268 bytes_retransmit=9 bytes_invalid=0 send_seq=2361 receive_seq=2361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63657 bytes_read=1017663 bytes_retransmit=0 bytes_invalid=0 send_seq=6458 receive_seq=6458 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998665 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.011 th0: temp=43.5 th1: temp=44.1 th2: temp=49.4 th3: temp=47.8 sysload=0.07 cputime=199.072 memavail=7396796 print_time=2271.018 buffer_time=2.148 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 59 Hz
Stats 2247.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18216213 bytes_read=2215709 bytes_retransmit=9 bytes_invalid=0 send_seq=316264 receive_seq=316264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015863 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14338 bytes_read=46175 bytes_retransmit=0 bytes_invalid=0 send_seq=2361 receive_seq=2361 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997247 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=93783 bytes_read=2865262 bytes_retransmit=9 bytes_invalid=0 send_seq=12552 receive_seq=12552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997649 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41494 bytes_read=647742 bytes_retransmit=9 bytes_invalid=0 send_seq=5169 receive_seq=5169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14551 bytes_read=570267 bytes_retransmit=9 bytes_invalid=0 send_seq=2371 receive_seq=2371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15091 bytes_read=45295 bytes_retransmit=9 bytes_invalid=0 send_seq=2362 receive_seq=2362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63663 bytes_read=1018013 bytes_retransmit=0 bytes_invalid=0 send_seq=6459 receive_seq=6459 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998652 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.011 th0: temp=43.3 th1: temp=44.2 th2: temp=49.5 th3: temp=47.8 sysload=0.06 cputime=199.161 memavail=7396796 print_time=2271.940 buffer_time=2.070 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 60 Hz
Stats 2248.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18219627 bytes_read=2216379 bytes_retransmit=9 bytes_invalid=0 send_seq=316336 receive_seq=316336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=400015861 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14344 bytes_read=46204 bytes_retransmit=0 bytes_invalid=0 send_seq=2362 receive_seq=2362 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997259 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=93859 bytes_read=2868348 bytes_retransmit=9 bytes_invalid=0 send_seq=12563 receive_seq=12563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997653 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41500 bytes_read=647856 bytes_retransmit=9 bytes_invalid=0 send_seq=5170 receive_seq=5170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997521 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14557 bytes_read=570546 bytes_retransmit=9 bytes_invalid=0 send_seq=2372 receive_seq=2372 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15097 bytes_read=45311 bytes_retransmit=9 bytes_invalid=0 send_seq=2363 receive_seq=2363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63669 bytes_read=1018369 bytes_retransmit=0 bytes_invalid=0 send_seq=6460 receive_seq=6460 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998664 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.011 th0: temp=43.5 th1: temp=44.2 th2: temp=49.6 th3: temp=48.1 sysload=0.06 cputime=199.259 memavail=7396796 print_time=2273.148 buffer_time=2.277 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 61 Hz
Stats 2249.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18222509 bytes_read=2217038 bytes_retransmit=9 bytes_invalid=0 send_seq=316400 receive_seq=316400 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=0 freq=400015860 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14350 bytes_read=46220 bytes_retransmit=0 bytes_invalid=0 send_seq=2363 receive_seq=2363 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997256 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=93935 bytes_read=2871462 bytes_retransmit=9 bytes_invalid=0 send_seq=12574 receive_seq=12574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997637 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41506 bytes_read=647970 bytes_retransmit=9 bytes_invalid=0 send_seq=5171 receive_seq=5171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997513 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14563 bytes_read=570795 bytes_retransmit=9 bytes_invalid=0 send_seq=2373 receive_seq=2373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15103 bytes_read=45327 bytes_retransmit=9 bytes_invalid=0 send_seq=2364 receive_seq=2364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63675 bytes_read=1018725 bytes_retransmit=0 bytes_invalid=0 send_seq=6461 receive_seq=6461 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998657 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.011 th0: temp=43.5 th1: temp=44.2 th2: temp=49.5 th3: temp=48.0 sysload=0.06 cputime=199.350 memavail=7396796 print_time=2274.038 buffer_time=2.166 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 62 Hz
Stats 2250.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18225041 bytes_read=2217654 bytes_retransmit=9 bytes_invalid=0 send_seq=316458 receive_seq=316458 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015865 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14356 bytes_read=46236 bytes_retransmit=0 bytes_invalid=0 send_seq=2364 receive_seq=2364 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997246 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94011 bytes_read=2874520 bytes_retransmit=9 bytes_invalid=0 send_seq=12585 receive_seq=12585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997617 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41512 bytes_read=648070 bytes_retransmit=9 bytes_invalid=0 send_seq=5172 receive_seq=5172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997525 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14569 bytes_read=571044 bytes_retransmit=9 bytes_invalid=0 send_seq=2374 receive_seq=2374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15109 bytes_read=45343 bytes_retransmit=9 bytes_invalid=0 send_seq=2365 receive_seq=2365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999449 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63681 bytes_read=1019081 bytes_retransmit=0 bytes_invalid=0 send_seq=6462 receive_seq=6462 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998652 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.7 th1: temp=44.3 th2: temp=49.7 th3: temp=47.9 sysload=0.06 cputime=199.442 memavail=7396816 print_time=2274.947 buffer_time=2.075 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Testing frequency 63 Hz
Stats 2251.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18228617 bytes_read=2218339 bytes_retransmit=9 bytes_invalid=0 send_seq=316533 receive_seq=316533 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=26 upcoming_bytes=0 freq=400015849 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14362 bytes_read=46252 bytes_retransmit=0 bytes_invalid=0 send_seq=2365 receive_seq=2365 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997246 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94087 bytes_read=2877622 bytes_retransmit=9 bytes_invalid=0 send_seq=12596 receive_seq=12596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997616 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41518 bytes_read=648198 bytes_retransmit=9 bytes_invalid=0 send_seq=5173 receive_seq=5173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997507 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14575 bytes_read=571323 bytes_retransmit=9 bytes_invalid=0 send_seq=2375 receive_seq=2375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997621 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15115 bytes_read=45359 bytes_retransmit=9 bytes_invalid=0 send_seq=2366 receive_seq=2366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63687 bytes_read=1019437 bytes_retransmit=0 bytes_invalid=0 send_seq=6463 receive_seq=6463 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998648 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.1 th2: temp=49.6 th3: temp=47.9 sysload=0.06 cputime=199.535 memavail=7396816 print_time=2276.165 buffer_time=2.292 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 64 Hz
Stats 2252.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18231539 bytes_read=2218998 bytes_retransmit=9 bytes_invalid=0 send_seq=316597 receive_seq=316597 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=23 upcoming_bytes=0 freq=400015842 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14368 bytes_read=46268 bytes_retransmit=0 bytes_invalid=0 send_seq=2366 receive_seq=2366 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997281 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94163 bytes_read=2880678 bytes_retransmit=9 bytes_invalid=0 send_seq=12607 receive_seq=12607 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997646 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41524 bytes_read=648312 bytes_retransmit=9 bytes_invalid=0 send_seq=5174 receive_seq=5174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997533 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14581 bytes_read=571572 bytes_retransmit=9 bytes_invalid=0 send_seq=2376 receive_seq=2376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15121 bytes_read=45386 bytes_retransmit=9 bytes_invalid=0 send_seq=2367 receive_seq=2367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999454 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63693 bytes_read=1019793 bytes_retransmit=0 bytes_invalid=0 send_seq=6464 receive_seq=6464 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998661 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.5 th2: temp=49.8 th3: temp=47.8 sysload=0.14 cputime=199.627 memavail=7397584 print_time=2277.036 buffer_time=2.163 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 65 Hz
Stats 2253.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18234135 bytes_read=2219608 bytes_retransmit=9 bytes_invalid=0 send_seq=316657 receive_seq=316657 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015939 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14374 bytes_read=46297 bytes_retransmit=0 bytes_invalid=0 send_seq=2367 receive_seq=2367 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997303 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94239 bytes_read=2883735 bytes_retransmit=9 bytes_invalid=0 send_seq=12618 receive_seq=12618 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997640 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41530 bytes_read=648412 bytes_retransmit=9 bytes_invalid=0 send_seq=5175 receive_seq=5175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997541 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14587 bytes_read=571806 bytes_retransmit=9 bytes_invalid=0 send_seq=2377 receive_seq=2377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15127 bytes_read=45402 bytes_retransmit=9 bytes_invalid=0 send_seq=2368 receive_seq=2368 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999454 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63699 bytes_read=1020149 bytes_retransmit=0 bytes_invalid=0 send_seq=6465 receive_seq=6465 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998659 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.5 th2: temp=49.6 th3: temp=48.0 sysload=0.14 cputime=199.713 memavail=7397684 print_time=2277.966 buffer_time=2.091 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 66 Hz
Stats 2254.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18237765 bytes_read=2220294 bytes_retransmit=9 bytes_invalid=0 send_seq=316733 receive_seq=316733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015919 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14380 bytes_read=46313 bytes_retransmit=0 bytes_invalid=0 send_seq=2368 receive_seq=2368 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997163 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94315 bytes_read=2886819 bytes_retransmit=9 bytes_invalid=0 send_seq=12629 receive_seq=12629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997430 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41536 bytes_read=648540 bytes_retransmit=9 bytes_invalid=0 send_seq=5176 receive_seq=5176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997423 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14593 bytes_read=572100 bytes_retransmit=9 bytes_invalid=0 send_seq=2378 receive_seq=2378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997493 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15133 bytes_read=45418 bytes_retransmit=9 bytes_invalid=0 send_seq=2369 receive_seq=2369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999414 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63705 bytes_read=1020505 bytes_retransmit=0 bytes_invalid=0 send_seq=6466 receive_seq=6466 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998554 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.7 th1: temp=44.5 th2: temp=49.5 th3: temp=48.0 sysload=0.14 cputime=199.809 memavail=7397688 print_time=2279.171 buffer_time=2.295 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 67 Hz
Stats 2255.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18240757 bytes_read=2220979 bytes_retransmit=9 bytes_invalid=0 send_seq=316799 receive_seq=316799 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015903 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14386 bytes_read=46329 bytes_retransmit=0 bytes_invalid=0 send_seq=2369 receive_seq=2369 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997218 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94391 bytes_read=2889876 bytes_retransmit=9 bytes_invalid=0 send_seq=12640 receive_seq=12640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997518 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41542 bytes_read=648640 bytes_retransmit=9 bytes_invalid=0 send_seq=5177 receive_seq=5177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997485 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14599 bytes_read=572349 bytes_retransmit=9 bytes_invalid=0 send_seq=2379 receive_seq=2379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997566 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15139 bytes_read=45434 bytes_retransmit=9 bytes_invalid=0 send_seq=2370 receive_seq=2370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999428 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63711 bytes_read=1020861 bytes_retransmit=0 bytes_invalid=0 send_seq=6467 receive_seq=6467 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998599 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=43.6 th1: temp=44.1 th2: temp=49.6 th3: temp=47.9 sysload=0.14 cputime=199.896 memavail=7397436 print_time=2280.054 buffer_time=2.177 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 68 Hz
Stats 2256.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18243522 bytes_read=2221594 bytes_retransmit=9 bytes_invalid=0 send_seq=316860 receive_seq=316860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015910 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14392 bytes_read=46345 bytes_retransmit=0 bytes_invalid=0 send_seq=2370 receive_seq=2370 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997248 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=94467 bytes_read=2893011 bytes_retransmit=9 bytes_invalid=0 send_seq=12651 receive_seq=12651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997549 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41548 bytes_read=648740 bytes_retransmit=9 bytes_invalid=0 send_seq=5178 receive_seq=5178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997508 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14605 bytes_read=572583 bytes_retransmit=9 bytes_invalid=0 send_seq=2380 receive_seq=2380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997589 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15145 bytes_read=45450 bytes_retransmit=9 bytes_invalid=0 send_seq=2371 receive_seq=2371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63717 bytes_read=1021217 bytes_retransmit=0 bytes_invalid=0 send_seq=6468 receive_seq=6468 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998619 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.6 th1: temp=44.4 th2: temp=49.8 th3: temp=48.0 sysload=0.14 cputime=199.984 memavail=7399016 print_time=2280.979 buffer_time=2.102 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 69 Hz
Stats 2257.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18247239 bytes_read=2222234 bytes_retransmit=9 bytes_invalid=0 send_seq=316937 receive_seq=316926 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=0 freq=400015901 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14398 bytes_read=46361 bytes_retransmit=0 bytes_invalid=0 send_seq=2371 receive_seq=2371 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997252 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=94543 bytes_read=2896096 bytes_retransmit=9 bytes_invalid=0 send_seq=12662 receive_seq=12662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997540 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=41554 bytes_read=648882 bytes_retransmit=9 bytes_invalid=0 send_seq=5179 receive_seq=5179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997502 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14611 bytes_read=572877 bytes_retransmit=9 bytes_invalid=0 send_seq=2381 receive_seq=2381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997580 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15151 bytes_read=45477 bytes_retransmit=9 bytes_invalid=0 send_seq=2372 receive_seq=2372 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63723 bytes_read=1021573 bytes_retransmit=0 bytes_invalid=0 send_seq=6469 receive_seq=6469 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998613 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.2 th1: temp=44.6 th2: temp=49.7 th3: temp=48.0 sysload=0.12 cputime=200.080 memavail=7399016 print_time=2282.188 buffer_time=2.309 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 70 Hz
Stats 2258.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18250292 bytes_read=2222979 bytes_retransmit=9 bytes_invalid=0 send_seq=317005 receive_seq=317005 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015885 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14410 bytes_read=46406 bytes_retransmit=0 bytes_invalid=0 send_seq=2373 receive_seq=2373 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997283 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=94625 bytes_read=2899156 bytes_retransmit=9 bytes_invalid=0 send_seq=12674 receive_seq=12674 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997583 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=41566 bytes_read=648991 bytes_retransmit=9 bytes_invalid=0 send_seq=5181 receive_seq=5181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14623 bytes_read=573127 bytes_retransmit=9 bytes_invalid=0 send_seq=2383 receive_seq=2383 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997609 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15163 bytes_read=45509 bytes_retransmit=9 bytes_invalid=0 send_seq=2374 receive_seq=2374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63735 bytes_read=1021945 bytes_retransmit=0 bytes_invalid=0 send_seq=6471 receive_seq=6471 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998637 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.8 th1: temp=44.3 th2: temp=49.8 th3: temp=48.0 sysload=0.12 cputime=200.170 memavail=7399016 print_time=2283.059 buffer_time=2.180 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 71 Hz
Stats 2259.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18253108 bytes_read=2223604 bytes_retransmit=9 bytes_invalid=0 send_seq=317068 receive_seq=317068 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015868 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14416 bytes_read=46422 bytes_retransmit=0 bytes_invalid=0 send_seq=2374 receive_seq=2374 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997304 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=94701 bytes_read=2902196 bytes_retransmit=9 bytes_invalid=0 send_seq=12685 receive_seq=12685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997660 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=41572 bytes_read=649084 bytes_retransmit=9 bytes_invalid=0 send_seq=5182 receive_seq=5182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14629 bytes_read=573361 bytes_retransmit=9 bytes_invalid=0 send_seq=2384 receive_seq=2384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997623 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15169 bytes_read=45525 bytes_retransmit=9 bytes_invalid=0 send_seq=2375 receive_seq=2375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999454 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63741 bytes_read=1022301 bytes_retransmit=0 bytes_invalid=0 send_seq=6472 receive_seq=6472 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998662 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.3 th1: temp=44.4 th2: temp=50.0 th3: temp=48.0 sysload=0.12 cputime=200.258 memavail=7399032 print_time=2283.991 buffer_time=2.111 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 72 Hz
Stats 2260.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18256141 bytes_read=2224265 bytes_retransmit=9 bytes_invalid=0 send_seq=317135 receive_seq=317135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015852 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14422 bytes_read=46438 bytes_retransmit=0 bytes_invalid=0 send_seq=2375 receive_seq=2375 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997311 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=94777 bytes_read=2905261 bytes_retransmit=9 bytes_invalid=0 send_seq=12696 receive_seq=12696 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997697 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=41578 bytes_read=649203 bytes_retransmit=9 bytes_invalid=0 send_seq=5183 receive_seq=5183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997566 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14635 bytes_read=573670 bytes_retransmit=9 bytes_invalid=0 send_seq=2385 receive_seq=2385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15175 bytes_read=45541 bytes_retransmit=9 bytes_invalid=0 send_seq=2376 receive_seq=2376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999457 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63747 bytes_read=1022657 bytes_retransmit=0 bytes_invalid=0 send_seq=6473 receive_seq=6473 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998672 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.3 th2: temp=49.6 th3: temp=48.1 sysload=0.12 cputime=200.346 memavail=7398824 print_time=2284.875 buffer_time=1.995 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 73 Hz
Stats 2261.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18260030 bytes_read=2225009 bytes_retransmit=9 bytes_invalid=0 send_seq=317216 receive_seq=317216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015868 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14428 bytes_read=46454 bytes_retransmit=0 bytes_invalid=0 send_seq=2376 receive_seq=2376 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997318 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94853 bytes_read=2908317 bytes_retransmit=9 bytes_invalid=0 send_seq=12707 receive_seq=12707 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997764 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=41584 bytes_read=649296 bytes_retransmit=9 bytes_invalid=0 send_seq=5184 receive_seq=5184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997592 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14641 bytes_read=573904 bytes_retransmit=9 bytes_invalid=0 send_seq=2386 receive_seq=2386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15181 bytes_read=45557 bytes_retransmit=9 bytes_invalid=0 send_seq=2377 receive_seq=2377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999461 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63753 bytes_read=1023013 bytes_retransmit=0 bytes_invalid=0 send_seq=6474 receive_seq=6474 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998688 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.4 th1: temp=44.1 th2: temp=49.7 th3: temp=48.1 sysload=0.12 cputime=200.442 memavail=7398824 print_time=2286.078 buffer_time=2.196 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 74 Hz
Stats 2262.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18263057 bytes_read=2225649 bytes_retransmit=9 bytes_invalid=0 send_seq=317282 receive_seq=317282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015853 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14434 bytes_read=46470 bytes_retransmit=0 bytes_invalid=0 send_seq=2377 receive_seq=2377 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997287 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94929 bytes_read=2911368 bytes_retransmit=9 bytes_invalid=0 send_seq=12718 receive_seq=12718 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997763 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=41590 bytes_read=649408 bytes_retransmit=9 bytes_invalid=0 send_seq=5185 receive_seq=5185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997527 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14647 bytes_read=574138 bytes_retransmit=9 bytes_invalid=0 send_seq=2387 receive_seq=2387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15187 bytes_read=45584 bytes_retransmit=9 bytes_invalid=0 send_seq=2378 receive_seq=2378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63759 bytes_read=1023369 bytes_retransmit=0 bytes_invalid=0 send_seq=6475 receive_seq=6475 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998672 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.6 th1: temp=44.4 th2: temp=49.7 th3: temp=48.1 sysload=0.11 cputime=200.529 memavail=7398824 print_time=2287.015 buffer_time=2.133 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2263.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18266046 bytes_read=2226289 bytes_retransmit=9 bytes_invalid=0 send_seq=317348 receive_seq=317348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015837 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14440 bytes_read=46486 bytes_retransmit=0 bytes_invalid=0 send_seq=2378 receive_seq=2378 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997312 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94998 bytes_read=2914487 bytes_retransmit=9 bytes_invalid=0 send_seq=12728 receive_seq=12728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997769 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=41596 bytes_read=649536 bytes_retransmit=9 bytes_invalid=0 send_seq=5186 receive_seq=5186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14653 bytes_read=574432 bytes_retransmit=9 bytes_invalid=0 send_seq=2388 receive_seq=2388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15193 bytes_read=45600 bytes_retransmit=9 bytes_invalid=0 send_seq=2379 receive_seq=2379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63765 bytes_read=1023725 bytes_retransmit=0 bytes_invalid=0 send_seq=6476 receive_seq=6476 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998688 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.3 th1: temp=44.6 th2: temp=49.8 th3: temp=48.0 sysload=0.11 cputime=200.615 memavail=7398824 print_time=2287.891 buffer_time=2.007 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 75 Hz
Testing frequency 76 Hz
Stats 2264.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18269936 bytes_read=2227036 bytes_retransmit=9 bytes_invalid=0 send_seq=317430 receive_seq=317430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=0 freq=400015825 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14446 bytes_read=46515 bytes_retransmit=0 bytes_invalid=0 send_seq=2379 receive_seq=2379 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997335 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95074 bytes_read=2917546 bytes_retransmit=9 bytes_invalid=0 send_seq=12739 receive_seq=12739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997764 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=41602 bytes_read=649636 bytes_retransmit=9 bytes_invalid=0 send_seq=5187 receive_seq=5187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997568 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14659 bytes_read=574666 bytes_retransmit=9 bytes_invalid=0 send_seq=2389 receive_seq=2389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15199 bytes_read=45616 bytes_retransmit=9 bytes_invalid=0 send_seq=2380 receive_seq=2380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999456 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63771 bytes_read=1024081 bytes_retransmit=0 bytes_invalid=0 send_seq=6477 receive_seq=6477 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998696 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.4 th1: temp=44.4 th2: temp=49.8 th3: temp=48.2 sysload=0.11 cputime=200.713 memavail=7398824 print_time=2289.085 buffer_time=2.201 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 77 Hz
Stats 2265.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18273038 bytes_read=2227700 bytes_retransmit=9 bytes_invalid=0 send_seq=317498 receive_seq=317498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015815 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14452 bytes_read=46531 bytes_retransmit=0 bytes_invalid=0 send_seq=2380 receive_seq=2380 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997340 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95150 bytes_read=2920605 bytes_retransmit=9 bytes_invalid=0 send_seq=12750 receive_seq=12750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997746 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=41608 bytes_read=649736 bytes_retransmit=9 bytes_invalid=0 send_seq=5188 receive_seq=5188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997684 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14665 bytes_read=574915 bytes_retransmit=9 bytes_invalid=0 send_seq=2390 receive_seq=2390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15205 bytes_read=45632 bytes_retransmit=9 bytes_invalid=0 send_seq=2381 receive_seq=2381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63777 bytes_read=1024437 bytes_retransmit=0 bytes_invalid=0 send_seq=6478 receive_seq=6478 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998692 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.8 th1: temp=44.5 th2: temp=49.8 th3: temp=48.3 sysload=0.11 cputime=200.803 memavail=7398824 print_time=2290.018 buffer_time=2.133 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2266.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18276081 bytes_read=2228345 bytes_retransmit=9 bytes_invalid=0 send_seq=317565 receive_seq=317565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015798 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14458 bytes_read=46547 bytes_retransmit=0 bytes_invalid=0 send_seq=2381 receive_seq=2381 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997344 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95226 bytes_read=2923707 bytes_retransmit=9 bytes_invalid=0 send_seq=12761 receive_seq=12761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997741 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=41614 bytes_read=649864 bytes_retransmit=9 bytes_invalid=0 send_seq=5189 receive_seq=5189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997665 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14671 bytes_read=575209 bytes_retransmit=9 bytes_invalid=0 send_seq=2391 receive_seq=2391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997689 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15211 bytes_read=45648 bytes_retransmit=9 bytes_invalid=0 send_seq=2382 receive_seq=2382 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999458 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63783 bytes_read=1024793 bytes_retransmit=0 bytes_invalid=0 send_seq=6479 receive_seq=6479 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998687 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.8 th1: temp=44.5 th2: temp=49.6 th3: temp=48.1 sysload=0.11 cputime=200.890 memavail=7399136 print_time=2290.886 buffer_time=2.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 78 Hz
Testing frequency 79 Hz
Stats 2267.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18280096 bytes_read=2229104 bytes_retransmit=9 bytes_invalid=0 send_seq=317649 receive_seq=317649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=0 freq=400015784 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14464 bytes_read=46563 bytes_retransmit=0 bytes_invalid=0 send_seq=2382 receive_seq=2382 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997362 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95302 bytes_read=2926765 bytes_retransmit=9 bytes_invalid=0 send_seq=12772 receive_seq=12772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997763 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41620 bytes_read=649978 bytes_retransmit=9 bytes_invalid=0 send_seq=5190 receive_seq=5190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997674 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14677 bytes_read=575443 bytes_retransmit=9 bytes_invalid=0 send_seq=2392 receive_seq=2392 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997712 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15217 bytes_read=45675 bytes_retransmit=9 bytes_invalid=0 send_seq=2383 receive_seq=2383 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999463 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63789 bytes_read=1025149 bytes_retransmit=0 bytes_invalid=0 send_seq=6480 receive_seq=6480 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998711 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.0 th1: temp=44.6 th2: temp=49.7 th3: temp=48.2 sysload=0.11 cputime=200.990 memavail=7398648 print_time=2292.095 buffer_time=2.208 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 80 Hz
Stats 2268.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18283341 bytes_read=2229764 bytes_retransmit=9 bytes_invalid=0 send_seq=317719 receive_seq=317719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015784 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14470 bytes_read=46579 bytes_retransmit=0 bytes_invalid=0 send_seq=2383 receive_seq=2383 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997344 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95378 bytes_read=2929824 bytes_retransmit=9 bytes_invalid=0 send_seq=12783 receive_seq=12783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997745 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41626 bytes_read=650078 bytes_retransmit=9 bytes_invalid=0 send_seq=5191 receive_seq=5191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997638 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14683 bytes_read=575677 bytes_retransmit=9 bytes_invalid=0 send_seq=2393 receive_seq=2393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997742 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15223 bytes_read=45691 bytes_retransmit=9 bytes_invalid=0 send_seq=2384 receive_seq=2384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999463 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63795 bytes_read=1025505 bytes_retransmit=0 bytes_invalid=0 send_seq=6481 receive_seq=6481 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998700 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.7 th1: temp=44.4 th2: temp=49.6 th3: temp=48.2 sysload=0.11 cputime=201.079 memavail=7398648 print_time=2293.030 buffer_time=2.143 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2269.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18286375 bytes_read=2230409 bytes_retransmit=9 bytes_invalid=0 send_seq=317786 receive_seq=317786 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015794 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14476 bytes_read=46608 bytes_retransmit=0 bytes_invalid=0 send_seq=2384 receive_seq=2384 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997342 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95454 bytes_read=2932909 bytes_retransmit=9 bytes_invalid=0 send_seq=12794 receive_seq=12794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997740 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41632 bytes_read=650206 bytes_retransmit=9 bytes_invalid=0 send_seq=5192 receive_seq=5192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997612 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14689 bytes_read=575971 bytes_retransmit=9 bytes_invalid=0 send_seq=2394 receive_seq=2394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997724 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15229 bytes_read=45707 bytes_retransmit=9 bytes_invalid=0 send_seq=2385 receive_seq=2385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999459 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63801 bytes_read=1025861 bytes_retransmit=0 bytes_invalid=0 send_seq=6482 receive_seq=6482 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998697 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.7 th2: temp=49.9 th3: temp=48.2 sysload=0.11 cputime=201.174 memavail=7392884 print_time=2293.906 buffer_time=2.018 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 81 Hz
Testing frequency 82 Hz
Stats 2270.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18290363 bytes_read=2231179 bytes_retransmit=9 bytes_invalid=0 send_seq=317869 receive_seq=317869 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=0 freq=400015779 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14482 bytes_read=46624 bytes_retransmit=0 bytes_invalid=0 send_seq=2385 receive_seq=2385 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997343 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95530 bytes_read=2936024 bytes_retransmit=9 bytes_invalid=0 send_seq=12805 receive_seq=12805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997715 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41638 bytes_read=650306 bytes_retransmit=9 bytes_invalid=0 send_seq=5193 receive_seq=5193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997569 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14695 bytes_read=576220 bytes_retransmit=9 bytes_invalid=0 send_seq=2395 receive_seq=2395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997721 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15235 bytes_read=45723 bytes_retransmit=9 bytes_invalid=0 send_seq=2386 receive_seq=2386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999453 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63807 bytes_read=1026217 bytes_retransmit=0 bytes_invalid=0 send_seq=6483 receive_seq=6483 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998693 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.6 th2: temp=50.1 th3: temp=48.3 sysload=0.11 cputime=201.280 memavail=7400012 print_time=2295.107 buffer_time=2.219 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 83 Hz
Stats 2271.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18293806 bytes_read=2231859 bytes_retransmit=9 bytes_invalid=0 send_seq=317943 receive_seq=317943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015769 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14488 bytes_read=46640 bytes_retransmit=0 bytes_invalid=0 send_seq=2386 receive_seq=2386 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997347 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95606 bytes_read=2939098 bytes_retransmit=9 bytes_invalid=0 send_seq=12816 receive_seq=12816 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997904 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41644 bytes_read=650406 bytes_retransmit=9 bytes_invalid=0 send_seq=5194 receive_seq=5194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997579 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14701 bytes_read=576454 bytes_retransmit=9 bytes_invalid=0 send_seq=2396 receive_seq=2396 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997713 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15241 bytes_read=45739 bytes_retransmit=9 bytes_invalid=0 send_seq=2387 receive_seq=2387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63813 bytes_read=1026573 bytes_retransmit=0 bytes_invalid=0 send_seq=6484 receive_seq=6484 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998694 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.8 th1: temp=45.2 th2: temp=49.8 th3: temp=47.8 sysload=0.11 cputime=201.455 memavail=7400012 print_time=2296.051 buffer_time=2.162 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 84 Hz
Stats 2272.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18296683 bytes_read=2232484 bytes_retransmit=9 bytes_invalid=0 send_seq=318006 receive_seq=318006 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015763 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14494 bytes_read=46656 bytes_retransmit=0 bytes_invalid=0 send_seq=2387 receive_seq=2387 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997340 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95682 bytes_read=2942184 bytes_retransmit=9 bytes_invalid=0 send_seq=12827 receive_seq=12827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997864 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41650 bytes_read=650548 bytes_retransmit=9 bytes_invalid=0 send_seq=5195 receive_seq=5195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997581 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14707 bytes_read=576748 bytes_retransmit=9 bytes_invalid=0 send_seq=2397 receive_seq=2397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997712 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15247 bytes_read=45766 bytes_retransmit=9 bytes_invalid=0 send_seq=2388 receive_seq=2388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63819 bytes_read=1026929 bytes_retransmit=0 bytes_invalid=0 send_seq=6485 receive_seq=6485 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998763 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.6 th1: temp=44.6 th2: temp=49.9 th3: temp=48.2 sysload=0.10 cputime=201.547 memavail=7400012 print_time=2296.912 buffer_time=2.023 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 85 Hz
Stats 2273.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18300862 bytes_read=2233243 bytes_retransmit=9 bytes_invalid=0 send_seq=318090 receive_seq=318090 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=13 upcoming_bytes=0 freq=400015750 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14500 bytes_read=46672 bytes_retransmit=0 bytes_invalid=0 send_seq=2388 receive_seq=2388 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997369 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95758 bytes_read=2945241 bytes_retransmit=9 bytes_invalid=0 send_seq=12838 receive_seq=12838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997841 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41656 bytes_read=650648 bytes_retransmit=9 bytes_invalid=0 send_seq=5196 receive_seq=5196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997583 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14713 bytes_read=576982 bytes_retransmit=9 bytes_invalid=0 send_seq=2398 receive_seq=2398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997709 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15253 bytes_read=45782 bytes_retransmit=9 bytes_invalid=0 send_seq=2389 receive_seq=2389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999460 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63825 bytes_read=1027285 bytes_retransmit=0 bytes_invalid=0 send_seq=6486 receive_seq=6486 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998767 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.7 th1: temp=44.6 th2: temp=49.9 th3: temp=48.2 sysload=0.10 cputime=201.648 memavail=7400012 print_time=2298.115 buffer_time=2.225 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 86 Hz
Stats 2274.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18304345 bytes_read=2233918 bytes_retransmit=9 bytes_invalid=0 send_seq=318163 receive_seq=318163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015749 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14506 bytes_read=46701 bytes_retransmit=0 bytes_invalid=0 send_seq=2389 receive_seq=2389 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997353 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95834 bytes_read=2948300 bytes_retransmit=9 bytes_invalid=0 send_seq=12849 receive_seq=12849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997809 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41662 bytes_read=650748 bytes_retransmit=9 bytes_invalid=0 send_seq=5197 receive_seq=5197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997580 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14719 bytes_read=577216 bytes_retransmit=9 bytes_invalid=0 send_seq=2399 receive_seq=2399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997705 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15259 bytes_read=45798 bytes_retransmit=9 bytes_invalid=0 send_seq=2390 receive_seq=2390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999459 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63831 bytes_read=1027641 bytes_retransmit=0 bytes_invalid=0 send_seq=6487 receive_seq=6487 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998756 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.0 th1: temp=44.6 th2: temp=49.8 th3: temp=48.2 sysload=0.10 cputime=201.742 memavail=7400012 print_time=2299.052 buffer_time=2.162 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 87 Hz
Stats 2275.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18307317 bytes_read=2234565 bytes_retransmit=9 bytes_invalid=0 send_seq=318228 receive_seq=318228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015742 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14512 bytes_read=46717 bytes_retransmit=0 bytes_invalid=0 send_seq=2390 receive_seq=2390 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997348 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95910 bytes_read=2951385 bytes_retransmit=9 bytes_invalid=0 send_seq=12860 receive_seq=12860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997771 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41668 bytes_read=650876 bytes_retransmit=9 bytes_invalid=0 send_seq=5198 receive_seq=5198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997573 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14725 bytes_read=577525 bytes_retransmit=9 bytes_invalid=0 send_seq=2400 receive_seq=2400 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997709 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15265 bytes_read=45814 bytes_retransmit=9 bytes_invalid=0 send_seq=2391 receive_seq=2391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63837 bytes_read=1027997 bytes_retransmit=0 bytes_invalid=0 send_seq=6488 receive_seq=6488 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998739 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.6 th1: temp=44.6 th2: temp=49.9 th3: temp=48.3 sysload=0.10 cputime=201.836 memavail=7398752 print_time=2299.916 buffer_time=2.025 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 88 Hz
Stats 2276.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18311561 bytes_read=2235337 bytes_retransmit=9 bytes_invalid=0 send_seq=318315 receive_seq=318315 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=43 upcoming_bytes=0 freq=400015735 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14518 bytes_read=46733 bytes_retransmit=0 bytes_invalid=0 send_seq=2391 receive_seq=2391 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997358 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95986 bytes_read=2954461 bytes_retransmit=9 bytes_invalid=0 send_seq=12871 receive_seq=12871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997763 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41674 bytes_read=650976 bytes_retransmit=9 bytes_invalid=0 send_seq=5199 receive_seq=5199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997724 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14731 bytes_read=577759 bytes_retransmit=9 bytes_invalid=0 send_seq=2401 receive_seq=2401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997928 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15271 bytes_read=45830 bytes_retransmit=9 bytes_invalid=0 send_seq=2392 receive_seq=2392 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999459 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63843 bytes_read=1028353 bytes_retransmit=0 bytes_invalid=0 send_seq=6489 receive_seq=6489 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998724 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.7 th1: temp=44.6 th2: temp=49.8 th3: temp=48.1 sysload=0.10 cputime=201.937 memavail=7398768 print_time=2301.120 buffer_time=2.229 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 89 Hz
Stats 2277.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18315104 bytes_read=2236022 bytes_retransmit=9 bytes_invalid=0 send_seq=318390 receive_seq=318390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015730 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14524 bytes_read=46749 bytes_retransmit=0 bytes_invalid=0 send_seq=2392 receive_seq=2392 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997345 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96055 bytes_read=2957553 bytes_retransmit=9 bytes_invalid=0 send_seq=12881 receive_seq=12881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997730 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41680 bytes_read=651090 bytes_retransmit=9 bytes_invalid=0 send_seq=5200 receive_seq=5200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997667 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14737 bytes_read=577993 bytes_retransmit=9 bytes_invalid=0 send_seq=2402 receive_seq=2402 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997849 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15277 bytes_read=45857 bytes_retransmit=9 bytes_invalid=0 send_seq=2393 receive_seq=2393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999456 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63849 bytes_read=1028709 bytes_retransmit=0 bytes_invalid=0 send_seq=6490 receive_seq=6490 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998703 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.6 th1: temp=44.8 th2: temp=49.9 th3: temp=48.2 sysload=0.09 cputime=202.030 memavail=7398768 print_time=2302.053 buffer_time=2.162 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 90 Hz
Stats 2278.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18318131 bytes_read=2236667 bytes_retransmit=9 bytes_invalid=0 send_seq=318457 receive_seq=318457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015718 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14530 bytes_read=46765 bytes_retransmit=0 bytes_invalid=0 send_seq=2393 receive_seq=2393 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997342 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96131 bytes_read=2960637 bytes_retransmit=9 bytes_invalid=0 send_seq=12892 receive_seq=12892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997714 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41686 bytes_read=651218 bytes_retransmit=9 bytes_invalid=0 send_seq=5201 receive_seq=5201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997653 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14743 bytes_read=578287 bytes_retransmit=9 bytes_invalid=0 send_seq=2403 receive_seq=2403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997813 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15283 bytes_read=45873 bytes_retransmit=9 bytes_invalid=0 send_seq=2394 receive_seq=2394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999456 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63855 bytes_read=1029065 bytes_retransmit=0 bytes_invalid=0 send_seq=6491 receive_seq=6491 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998700 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.7 th1: temp=44.8 th2: temp=50.0 th3: temp=48.3 sysload=0.09 cputime=202.123 memavail=7398768 print_time=2302.933 buffer_time=2.041 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 91 Hz
Stats 2279.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18322366 bytes_read=2237441 bytes_retransmit=9 bytes_invalid=0 send_seq=318544 receive_seq=318544 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=0 freq=400015709 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14536 bytes_read=46794 bytes_retransmit=0 bytes_invalid=0 send_seq=2394 receive_seq=2394 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997349 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96207 bytes_read=2963693 bytes_retransmit=9 bytes_invalid=0 send_seq=12903 receive_seq=12903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997712 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41692 bytes_read=651318 bytes_retransmit=9 bytes_invalid=0 send_seq=5202 receive_seq=5202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997785 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14749 bytes_read=578521 bytes_retransmit=9 bytes_invalid=0 send_seq=2404 receive_seq=2404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997801 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15289 bytes_read=45889 bytes_retransmit=9 bytes_invalid=0 send_seq=2395 receive_seq=2395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999458 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63861 bytes_read=1029421 bytes_retransmit=0 bytes_invalid=0 send_seq=6492 receive_seq=6492 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998700 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=43.7 th1: temp=44.7 th2: temp=50.1 th3: temp=48.3 sysload=0.09 cputime=202.225 memavail=7398768 print_time=2304.136 buffer_time=2.243 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 92 Hz
Stats 2280.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18326055 bytes_read=2238157 bytes_retransmit=9 bytes_invalid=0 send_seq=318622 receive_seq=318622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015725 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14542 bytes_read=46810 bytes_retransmit=0 bytes_invalid=0 send_seq=2395 receive_seq=2395 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997342 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96283 bytes_read=2966750 bytes_retransmit=9 bytes_invalid=0 send_seq=12914 receive_seq=12914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997703 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41698 bytes_read=651418 bytes_retransmit=9 bytes_invalid=0 send_seq=5203 receive_seq=5203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997713 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14755 bytes_read=578770 bytes_retransmit=9 bytes_invalid=0 send_seq=2405 receive_seq=2405 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997757 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15295 bytes_read=45905 bytes_retransmit=9 bytes_invalid=0 send_seq=2396 receive_seq=2396 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999458 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63867 bytes_read=1029777 bytes_retransmit=0 bytes_invalid=0 send_seq=6493 receive_seq=6493 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998692 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.6 th1: temp=44.8 th2: temp=49.9 th3: temp=48.4 sysload=0.09 cputime=202.319 memavail=7398780 print_time=2305.071 buffer_time=2.179 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 93 Hz
Stats 2281.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18329042 bytes_read=2238797 bytes_retransmit=9 bytes_invalid=0 send_seq=318688 receive_seq=318688 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015738 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14548 bytes_read=46826 bytes_retransmit=0 bytes_invalid=0 send_seq=2396 receive_seq=2396 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997293 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96359 bytes_read=2969854 bytes_retransmit=9 bytes_invalid=0 send_seq=12925 receive_seq=12925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997656 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41704 bytes_read=651546 bytes_retransmit=9 bytes_invalid=0 send_seq=5204 receive_seq=5204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997635 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14761 bytes_read=579064 bytes_retransmit=9 bytes_invalid=0 send_seq=2406 receive_seq=2406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997705 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15301 bytes_read=45921 bytes_retransmit=9 bytes_invalid=0 send_seq=2397 receive_seq=2397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63873 bytes_read=1030133 bytes_retransmit=0 bytes_invalid=0 send_seq=6494 receive_seq=6494 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998671 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.8 th1: temp=45.1 th2: temp=49.9 th3: temp=48.2 sysload=0.09 cputime=202.412 memavail=7398780 print_time=2305.941 buffer_time=2.048 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 94 Hz
Stats 2282.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18333428 bytes_read=2239516 bytes_retransmit=9 bytes_invalid=0 send_seq=318774 receive_seq=318764 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=15 upcoming_bytes=0 freq=400015751 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14554 bytes_read=46842 bytes_retransmit=0 bytes_invalid=0 send_seq=2397 receive_seq=2397 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997276 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96435 bytes_read=2972911 bytes_retransmit=9 bytes_invalid=0 send_seq=12936 receive_seq=12936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997627 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41710 bytes_read=651660 bytes_retransmit=9 bytes_invalid=0 send_seq=5205 receive_seq=5205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14767 bytes_read=579298 bytes_retransmit=9 bytes_invalid=0 send_seq=2407 receive_seq=2407 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15307 bytes_read=45948 bytes_retransmit=9 bytes_invalid=0 send_seq=2398 receive_seq=2398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63879 bytes_read=1030489 bytes_retransmit=0 bytes_invalid=0 send_seq=6495 receive_seq=6495 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998655 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.9 th1: temp=44.7 th2: temp=50.0 th3: temp=48.3 sysload=0.08 cputime=202.517 memavail=7398800 print_time=2307.140 buffer_time=2.247 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 95 Hz
Stats 2283.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18337198 bytes_read=2240276 bytes_retransmit=9 bytes_invalid=0 send_seq=318854 receive_seq=318854 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=0 freq=400015762 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14560 bytes_read=46858 bytes_retransmit=0 bytes_invalid=0 send_seq=2398 receive_seq=2398 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997268 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96511 bytes_read=2975967 bytes_retransmit=9 bytes_invalid=0 send_seq=12947 receive_seq=12947 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997613 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41716 bytes_read=651760 bytes_retransmit=9 bytes_invalid=0 send_seq=5206 receive_seq=5206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997522 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14773 bytes_read=579532 bytes_retransmit=9 bytes_invalid=0 send_seq=2408 receive_seq=2408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15313 bytes_read=45964 bytes_retransmit=9 bytes_invalid=0 send_seq=2399 receive_seq=2399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63885 bytes_read=1030845 bytes_retransmit=0 bytes_invalid=0 send_seq=6496 receive_seq=6496 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998636 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.8 th1: temp=44.8 th2: temp=49.8 th3: temp=48.3 sysload=0.08 cputime=202.614 memavail=7398800 print_time=2308.077 buffer_time=2.184 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 96 Hz
Stats 2284.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18340221 bytes_read=2240916 bytes_retransmit=9 bytes_invalid=0 send_seq=318920 receive_seq=318920 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015771 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14566 bytes_read=46887 bytes_retransmit=0 bytes_invalid=0 send_seq=2399 receive_seq=2399 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997254 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96587 bytes_read=2979054 bytes_retransmit=9 bytes_invalid=0 send_seq=12958 receive_seq=12958 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997589 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41722 bytes_read=651888 bytes_retransmit=9 bytes_invalid=0 send_seq=5207 receive_seq=5207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997483 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14779 bytes_read=579826 bytes_retransmit=9 bytes_invalid=0 send_seq=2409 receive_seq=2409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997610 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15319 bytes_read=45980 bytes_retransmit=9 bytes_invalid=0 send_seq=2400 receive_seq=2400 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63891 bytes_read=1031185 bytes_retransmit=0 bytes_invalid=0 send_seq=6497 receive_seq=6497 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998623 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.7 th1: temp=44.8 th2: temp=50.1 th3: temp=48.5 sysload=0.08 cputime=202.710 memavail=7398796 print_time=2308.948 buffer_time=2.054 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 97 Hz
Stats 2285.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18344604 bytes_read=2241716 bytes_retransmit=9 bytes_invalid=0 send_seq=319009 receive_seq=319009 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=22 upcoming_bytes=0 freq=400015782 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14572 bytes_read=46903 bytes_retransmit=0 bytes_invalid=0 send_seq=2400 receive_seq=2400 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997234 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96663 bytes_read=2982168 bytes_retransmit=9 bytes_invalid=0 send_seq=12969 receive_seq=12969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997582 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41728 bytes_read=651988 bytes_retransmit=9 bytes_invalid=0 send_seq=5208 receive_seq=5208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997453 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14785 bytes_read=580075 bytes_retransmit=9 bytes_invalid=0 send_seq=2410 receive_seq=2410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997587 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15325 bytes_read=45996 bytes_retransmit=9 bytes_invalid=0 send_seq=2401 receive_seq=2401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63897 bytes_read=1031557 bytes_retransmit=0 bytes_invalid=0 send_seq=6498 receive_seq=6498 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998609 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.8 th1: temp=44.8 th2: temp=50.0 th3: temp=48.5 sysload=0.08 cputime=202.819 memavail=7398556 print_time=2310.148 buffer_time=2.250 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 98 Hz
Stats 2286.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18348436 bytes_read=2242415 bytes_retransmit=9 bytes_invalid=0 send_seq=319088 receive_seq=319088 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015800 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14578 bytes_read=46919 bytes_retransmit=0 bytes_invalid=0 send_seq=2401 receive_seq=2401 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997260 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96739 bytes_read=2985243 bytes_retransmit=9 bytes_invalid=0 send_seq=12980 receive_seq=12980 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997662 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41734 bytes_read=652088 bytes_retransmit=9 bytes_invalid=0 send_seq=5209 receive_seq=5209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997436 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14791 bytes_read=580309 bytes_retransmit=9 bytes_invalid=0 send_seq=2411 receive_seq=2411 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997600 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15331 bytes_read=46012 bytes_retransmit=9 bytes_invalid=0 send_seq=2402 receive_seq=2402 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63903 bytes_read=1031913 bytes_retransmit=0 bytes_invalid=0 send_seq=6499 receive_seq=6499 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998614 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.4 th1: temp=45.0 th2: temp=49.9 th3: temp=48.4 sysload=0.08 cputime=202.919 memavail=7394784 print_time=2311.080 buffer_time=2.181 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 99 Hz
Stats 2287.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18351522 bytes_read=2243070 bytes_retransmit=9 bytes_invalid=0 send_seq=319157 receive_seq=319157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015791 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14584 bytes_read=46935 bytes_retransmit=0 bytes_invalid=0 send_seq=2402 receive_seq=2402 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999273 adj=49997219 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96815 bytes_read=2988327 bytes_retransmit=9 bytes_invalid=0 send_seq=12991 receive_seq=12991 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997627 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41740 bytes_read=652230 bytes_retransmit=9 bytes_invalid=0 send_seq=5210 receive_seq=5210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997402 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14797 bytes_read=580603 bytes_retransmit=9 bytes_invalid=0 send_seq=2412 receive_seq=2412 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997570 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15337 bytes_read=46039 bytes_retransmit=9 bytes_invalid=0 send_seq=2403 receive_seq=2403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999433 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63909 bytes_read=1032253 bytes_retransmit=0 bytes_invalid=0 send_seq=6500 receive_seq=6500 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998596 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.6 th1: temp=45.0 th2: temp=50.2 th3: temp=48.3 sysload=0.24 cputime=203.020 memavail=7398924 print_time=2311.952 buffer_time=2.052 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 100 Hz
Stats 2288.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18356053 bytes_read=2243864 bytes_retransmit=9 bytes_invalid=0 send_seq=319248 receive_seq=319248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015799 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14590 bytes_read=46951 bytes_retransmit=0 bytes_invalid=0 send_seq=2403 receive_seq=2403 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999272 adj=49997455 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96891 bytes_read=2991384 bytes_retransmit=9 bytes_invalid=0 send_seq=13002 receive_seq=13002 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997628 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41746 bytes_read=652330 bytes_retransmit=9 bytes_invalid=0 send_seq=5211 receive_seq=5211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997417 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14803 bytes_read=580837 bytes_retransmit=9 bytes_invalid=0 send_seq=2413 receive_seq=2413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997595 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15343 bytes_read=46055 bytes_retransmit=9 bytes_invalid=0 send_seq=2404 receive_seq=2404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999460 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63915 bytes_read=1032625 bytes_retransmit=0 bytes_invalid=0 send_seq=6501 receive_seq=6501 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998608 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=43.9 th1: temp=45.0 th2: temp=50.1 th3: temp=48.4 sysload=0.24 cputime=203.126 memavail=7398924 print_time=2313.149 buffer_time=2.242 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 101 Hz
Stats 2289.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18359934 bytes_read=2244579 bytes_retransmit=9 bytes_invalid=0 send_seq=319329 receive_seq=319329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=400015806 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14596 bytes_read=46980 bytes_retransmit=0 bytes_invalid=0 send_seq=2404 receive_seq=2404 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999270 adj=49997388 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96967 bytes_read=2994501 bytes_retransmit=9 bytes_invalid=0 send_seq=13013 receive_seq=13013 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997653 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41752 bytes_read=652430 bytes_retransmit=9 bytes_invalid=0 send_seq=5212 receive_seq=5212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997423 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14809 bytes_read=581071 bytes_retransmit=9 bytes_invalid=0 send_seq=2414 receive_seq=2414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997602 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15349 bytes_read=46071 bytes_retransmit=9 bytes_invalid=0 send_seq=2405 receive_seq=2405 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63921 bytes_read=1032981 bytes_retransmit=0 bytes_invalid=0 send_seq=6502 receive_seq=6502 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998610 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.6 th1: temp=45.1 th2: temp=50.0 th3: temp=48.4 sysload=0.24 cputime=203.222 memavail=7398700 print_time=2314.088 buffer_time=2.180 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 102 Hz
Stats 2290.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18363057 bytes_read=2245235 bytes_retransmit=9 bytes_invalid=0 send_seq=319395 receive_seq=319395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015809 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14602 bytes_read=46996 bytes_retransmit=0 bytes_invalid=0 send_seq=2405 receive_seq=2405 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999275 adj=49997341 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97036 bytes_read=2997564 bytes_retransmit=9 bytes_invalid=0 send_seq=13023 receive_seq=13023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997625 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41758 bytes_read=652558 bytes_retransmit=9 bytes_invalid=0 send_seq=5213 receive_seq=5213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997411 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14815 bytes_read=581380 bytes_retransmit=9 bytes_invalid=0 send_seq=2415 receive_seq=2415 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997588 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15355 bytes_read=46087 bytes_retransmit=9 bytes_invalid=0 send_seq=2406 receive_seq=2406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999445 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63927 bytes_read=1033337 bytes_retransmit=0 bytes_invalid=0 send_seq=6503 receive_seq=6503 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998611 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.9 th1: temp=44.8 th2: temp=50.2 th3: temp=48.5 sysload=0.24 cputime=203.322 memavail=7398464 print_time=2314.959 buffer_time=2.051 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 103 Hz
Stats 2291.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18367610 bytes_read=2246029 bytes_retransmit=9 bytes_invalid=0 send_seq=319486 receive_seq=319486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=0 freq=400015811 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14608 bytes_read=47012 bytes_retransmit=0 bytes_invalid=0 send_seq=2406 receive_seq=2406 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999273 adj=49997387 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97112 bytes_read=3000637 bytes_retransmit=9 bytes_invalid=0 send_seq=13034 receive_seq=13034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997614 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41764 bytes_read=652658 bytes_retransmit=9 bytes_invalid=0 send_seq=5214 receive_seq=5214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997423 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14821 bytes_read=581614 bytes_retransmit=9 bytes_invalid=0 send_seq=2416 receive_seq=2416 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997584 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15361 bytes_read=46103 bytes_retransmit=9 bytes_invalid=0 send_seq=2407 receive_seq=2407 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63933 bytes_read=1033677 bytes_retransmit=0 bytes_invalid=0 send_seq=6504 receive_seq=6504 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998615 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.9 th2: temp=50.2 th3: temp=48.5 sysload=0.24 cputime=203.430 memavail=7398464 print_time=2316.160 buffer_time=2.251 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 104 Hz
Stats 2292.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18371546 bytes_read=2246744 bytes_retransmit=9 bytes_invalid=0 send_seq=319567 receive_seq=319567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015832 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14614 bytes_read=47028 bytes_retransmit=0 bytes_invalid=0 send_seq=2407 receive_seq=2407 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999271 adj=49997334 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97188 bytes_read=3003695 bytes_retransmit=9 bytes_invalid=0 send_seq=13045 receive_seq=13045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997616 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=41770 bytes_read=652772 bytes_retransmit=9 bytes_invalid=0 send_seq=5215 receive_seq=5215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997439 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14827 bytes_read=581848 bytes_retransmit=9 bytes_invalid=0 send_seq=2417 receive_seq=2417 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997595 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15367 bytes_read=46130 bytes_retransmit=9 bytes_invalid=0 send_seq=2408 receive_seq=2408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63939 bytes_read=1034033 bytes_retransmit=0 bytes_invalid=0 send_seq=6505 receive_seq=6505 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998623 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.3 th1: temp=45.0 th2: temp=50.1 th3: temp=48.5 sysload=0.22 cputime=203.527 memavail=7398464 print_time=2317.090 buffer_time=2.181 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 105 Hz
Stats 2293.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18374764 bytes_read=2247394 bytes_retransmit=9 bytes_invalid=0 send_seq=319635 receive_seq=319635 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015842 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14620 bytes_read=47044 bytes_retransmit=0 bytes_invalid=0 send_seq=2408 receive_seq=2408 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999269 adj=49997273 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97264 bytes_read=3006780 bytes_retransmit=9 bytes_invalid=0 send_seq=13056 receive_seq=13056 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997566 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=41776 bytes_read=652900 bytes_retransmit=9 bytes_invalid=0 send_seq=5216 receive_seq=5216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997395 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14833 bytes_read=582142 bytes_retransmit=9 bytes_invalid=0 send_seq=2418 receive_seq=2418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997563 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15373 bytes_read=46146 bytes_retransmit=9 bytes_invalid=0 send_seq=2409 receive_seq=2409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999434 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63945 bytes_read=1034389 bytes_retransmit=0 bytes_invalid=0 send_seq=6506 receive_seq=6506 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998599 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.7 th1: temp=44.9 th2: temp=50.1 th3: temp=48.4 sysload=0.22 cputime=203.625 memavail=7398464 print_time=2317.965 buffer_time=2.055 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 106 Hz
Stats 2294.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18379354 bytes_read=2248163 bytes_retransmit=9 bytes_invalid=0 send_seq=319726 receive_seq=319721 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=22 upcoming_bytes=0 freq=400015845 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14626 bytes_read=47073 bytes_retransmit=0 bytes_invalid=0 send_seq=2409 receive_seq=2409 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999268 adj=49997234 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97340 bytes_read=3009897 bytes_retransmit=9 bytes_invalid=0 send_seq=13067 receive_seq=13067 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997545 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=41782 bytes_read=653000 bytes_retransmit=9 bytes_invalid=0 send_seq=5217 receive_seq=5217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997374 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14839 bytes_read=582376 bytes_retransmit=9 bytes_invalid=0 send_seq=2419 receive_seq=2419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997561 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15379 bytes_read=46162 bytes_retransmit=9 bytes_invalid=0 send_seq=2410 receive_seq=2410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999431 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63951 bytes_read=1034779 bytes_retransmit=0 bytes_invalid=0 send_seq=6507 receive_seq=6507 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998588 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.9 th1: temp=45.0 th2: temp=50.1 th3: temp=48.5 sysload=0.22 cputime=203.736 memavail=7398464 print_time=2319.156 buffer_time=2.238 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 107 Hz
Stats 2295.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18383398 bytes_read=2248934 bytes_retransmit=9 bytes_invalid=0 send_seq=319810 receive_seq=319810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=400015846 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14632 bytes_read=47089 bytes_retransmit=0 bytes_invalid=0 send_seq=2410 receive_seq=2410 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999266 adj=49997232 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97416 bytes_read=3012955 bytes_retransmit=9 bytes_invalid=0 send_seq=13078 receive_seq=13078 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997564 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=41788 bytes_read=653100 bytes_retransmit=9 bytes_invalid=0 send_seq=5218 receive_seq=5218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997417 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14845 bytes_read=582625 bytes_retransmit=9 bytes_invalid=0 send_seq=2420 receive_seq=2420 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997599 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15385 bytes_read=46178 bytes_retransmit=9 bytes_invalid=0 send_seq=2411 receive_seq=2411 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63957 bytes_read=1035135 bytes_retransmit=0 bytes_invalid=0 send_seq=6508 receive_seq=6508 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998602 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.8 th1: temp=45.1 th2: temp=50.1 th3: temp=48.4 sysload=0.22 cputime=203.839 memavail=7398216 print_time=2320.093 buffer_time=2.175 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 108 Hz
Stats 2296.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18386644 bytes_read=2249594 bytes_retransmit=9 bytes_invalid=0 send_seq=319880 receive_seq=319880 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015853 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14638 bytes_read=47105 bytes_retransmit=0 bytes_invalid=0 send_seq=2411 receive_seq=2411 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999265 adj=49997222 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97492 bytes_read=3016058 bytes_retransmit=9 bytes_invalid=0 send_seq=13089 receive_seq=13089 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997570 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=41794 bytes_read=653228 bytes_retransmit=9 bytes_invalid=0 send_seq=5219 receive_seq=5219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997425 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14851 bytes_read=582919 bytes_retransmit=9 bytes_invalid=0 send_seq=2421 receive_seq=2421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997599 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15391 bytes_read=46194 bytes_retransmit=9 bytes_invalid=0 send_seq=2412 receive_seq=2412 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63963 bytes_read=1035475 bytes_retransmit=0 bytes_invalid=0 send_seq=6509 receive_seq=6509 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998619 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.1 th1: temp=45.2 th2: temp=50.1 th3: temp=48.7 sysload=0.22 cputime=203.938 memavail=7398232 print_time=2320.969 buffer_time=2.051 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 109 Hz
Stats 2297.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18391376 bytes_read=2250403 bytes_retransmit=9 bytes_invalid=0 send_seq=319975 receive_seq=319975 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=0 freq=400015874 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14644 bytes_read=47121 bytes_retransmit=0 bytes_invalid=0 send_seq=2412 receive_seq=2412 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999265 adj=49997203 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97568 bytes_read=3019114 bytes_retransmit=9 bytes_invalid=0 send_seq=13100 receive_seq=13100 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997555 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41800 bytes_read=653342 bytes_retransmit=9 bytes_invalid=0 send_seq=5220 receive_seq=5220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997409 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14857 bytes_read=583153 bytes_retransmit=9 bytes_invalid=0 send_seq=2422 receive_seq=2422 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15397 bytes_read=46221 bytes_retransmit=9 bytes_invalid=0 send_seq=2413 receive_seq=2413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999431 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63969 bytes_read=1035847 bytes_retransmit=0 bytes_invalid=0 send_seq=6510 receive_seq=6510 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998619 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.9 th1: temp=44.9 th2: temp=50.1 th3: temp=48.6 sysload=0.20 cputime=204.049 memavail=7398232 print_time=2322.172 buffer_time=2.249 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 110 Hz
Stats 2298.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18395502 bytes_read=2251138 bytes_retransmit=9 bytes_invalid=0 send_seq=320060 receive_seq=320060 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015879 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14650 bytes_read=47137 bytes_retransmit=0 bytes_invalid=0 send_seq=2413 receive_seq=2413 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999264 adj=49997190 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97644 bytes_read=3022173 bytes_retransmit=9 bytes_invalid=0 send_seq=13111 receive_seq=13111 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997539 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41806 bytes_read=653442 bytes_retransmit=9 bytes_invalid=0 send_seq=5221 receive_seq=5221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997399 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14863 bytes_read=583387 bytes_retransmit=9 bytes_invalid=0 send_seq=2423 receive_seq=2423 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997603 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15403 bytes_read=46237 bytes_retransmit=9 bytes_invalid=0 send_seq=2414 receive_seq=2414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999426 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63975 bytes_read=1036203 bytes_retransmit=0 bytes_invalid=0 send_seq=6511 receive_seq=6511 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998606 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.9 th1: temp=45.1 th2: temp=50.1 th3: temp=48.6 sysload=0.20 cputime=204.149 memavail=7398232 print_time=2323.100 buffer_time=2.176 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 111 Hz
Stats 2299.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18398749 bytes_read=2251798 bytes_retransmit=9 bytes_invalid=0 send_seq=320130 receive_seq=320130 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015880 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14656 bytes_read=47166 bytes_retransmit=0 bytes_invalid=0 send_seq=2414 receive_seq=2414 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999263 adj=49997186 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97720 bytes_read=3025257 bytes_retransmit=9 bytes_invalid=0 send_seq=13122 receive_seq=13122 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997533 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41812 bytes_read=653570 bytes_retransmit=9 bytes_invalid=0 send_seq=5222 receive_seq=5222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997394 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14869 bytes_read=583681 bytes_retransmit=9 bytes_invalid=0 send_seq=2424 receive_seq=2424 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997589 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15409 bytes_read=46253 bytes_retransmit=9 bytes_invalid=0 send_seq=2415 receive_seq=2415 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999425 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63981 bytes_read=1036543 bytes_retransmit=0 bytes_invalid=0 send_seq=6512 receive_seq=6512 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998599 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.8 th1: temp=45.2 th2: temp=50.1 th3: temp=48.6 sysload=0.20 cputime=204.247 memavail=7398240 print_time=2323.974 buffer_time=2.050 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 112 Hz
Stats 2300.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18403462 bytes_read=2252628 bytes_retransmit=9 bytes_invalid=0 send_seq=320225 receive_seq=320225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=0 freq=400015882 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14662 bytes_read=47182 bytes_retransmit=0 bytes_invalid=0 send_seq=2415 receive_seq=2415 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999265 adj=49997186 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97796 bytes_read=3028371 bytes_retransmit=9 bytes_invalid=0 send_seq=13133 receive_seq=13133 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997539 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41818 bytes_read=653670 bytes_retransmit=9 bytes_invalid=0 send_seq=5223 receive_seq=5223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997405 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14875 bytes_read=583930 bytes_retransmit=9 bytes_invalid=0 send_seq=2425 receive_seq=2425 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997585 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15415 bytes_read=46269 bytes_retransmit=9 bytes_invalid=0 send_seq=2416 receive_seq=2416 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999425 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63987 bytes_read=1036899 bytes_retransmit=0 bytes_invalid=0 send_seq=6513 receive_seq=6513 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998600 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=43.9 th1: temp=45.1 th2: temp=50.3 th3: temp=48.6 sysload=0.20 cputime=204.359 memavail=7398240 print_time=2325.170 buffer_time=2.246 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 113 Hz
Stats 2301.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18407646 bytes_read=2253358 bytes_retransmit=9 bytes_invalid=0 send_seq=320309 receive_seq=320309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015881 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14668 bytes_read=47198 bytes_retransmit=0 bytes_invalid=0 send_seq=2416 receive_seq=2416 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999264 adj=49997232 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97872 bytes_read=3031446 bytes_retransmit=9 bytes_invalid=0 send_seq=13144 receive_seq=13144 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997561 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41824 bytes_read=653770 bytes_retransmit=9 bytes_invalid=0 send_seq=5224 receive_seq=5224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14881 bytes_read=584164 bytes_retransmit=9 bytes_invalid=0 send_seq=2426 receive_seq=2426 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997592 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15421 bytes_read=46285 bytes_retransmit=9 bytes_invalid=0 send_seq=2417 receive_seq=2417 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999428 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63993 bytes_read=1037255 bytes_retransmit=0 bytes_invalid=0 send_seq=6514 receive_seq=6514 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998607 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.8 th1: temp=45.0 th2: temp=50.2 th3: temp=48.5 sysload=0.20 cputime=204.458 memavail=7398248 print_time=2326.108 buffer_time=2.184 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Testing frequency 114 Hz
Stats 2302.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18410881 bytes_read=2254023 bytes_retransmit=9 bytes_invalid=0 send_seq=320380 receive_seq=320380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015873 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14674 bytes_read=47214 bytes_retransmit=0 bytes_invalid=0 send_seq=2417 receive_seq=2417 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999262 adj=49997230 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97948 bytes_read=3034531 bytes_retransmit=9 bytes_invalid=0 send_seq=13155 receive_seq=13155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997581 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41830 bytes_read=653912 bytes_retransmit=9 bytes_invalid=0 send_seq=5225 receive_seq=5225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997533 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14887 bytes_read=584450 bytes_retransmit=9 bytes_invalid=0 send_seq=2427 receive_seq=2427 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997591 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15427 bytes_read=46312 bytes_retransmit=9 bytes_invalid=0 send_seq=2418 receive_seq=2418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999429 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=63999 bytes_read=1037611 bytes_retransmit=0 bytes_invalid=0 send_seq=6515 receive_seq=6515 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998634 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.9 th1: temp=45.3 th2: temp=50.2 th3: temp=48.7 sysload=0.18 cputime=204.558 memavail=7398252 print_time=2326.977 buffer_time=2.053 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 115 Hz
Stats 2303.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18415742 bytes_read=2254787 bytes_retransmit=9 bytes_invalid=0 send_seq=320474 receive_seq=320465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015880 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14680 bytes_read=47230 bytes_retransmit=0 bytes_invalid=0 send_seq=2418 receive_seq=2418 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999260 adj=49997223 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98024 bytes_read=3037589 bytes_retransmit=9 bytes_invalid=0 send_seq=13166 receive_seq=13166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997598 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41836 bytes_read=654012 bytes_retransmit=9 bytes_invalid=0 send_seq=5226 receive_seq=5226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997533 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14893 bytes_read=584668 bytes_retransmit=9 bytes_invalid=0 send_seq=2428 receive_seq=2428 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997598 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15433 bytes_read=46328 bytes_retransmit=9 bytes_invalid=0 send_seq=2419 receive_seq=2419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64005 bytes_read=1037967 bytes_retransmit=0 bytes_invalid=0 send_seq=6516 receive_seq=6516 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998639 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.0 th1: temp=45.0 th2: temp=50.2 th3: temp=48.6 sysload=0.18 cputime=204.669 memavail=7398252 print_time=2328.177 buffer_time=2.245 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 116 Hz
Stats 2304.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18419943 bytes_read=2255577 bytes_retransmit=9 bytes_invalid=0 send_seq=320561 receive_seq=320561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015881 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14686 bytes_read=47259 bytes_retransmit=0 bytes_invalid=0 send_seq=2419 receive_seq=2419 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999260 adj=49997205 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98100 bytes_read=3040645 bytes_retransmit=9 bytes_invalid=0 send_seq=13177 receive_seq=13177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997596 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41842 bytes_read=654112 bytes_retransmit=9 bytes_invalid=0 send_seq=5227 receive_seq=5227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997494 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=14899 bytes_read=584885 bytes_retransmit=9 bytes_invalid=0 send_seq=2429 receive_seq=2429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997597 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15439 bytes_read=46344 bytes_retransmit=9 bytes_invalid=0 send_seq=2420 receive_seq=2420 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999436 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64011 bytes_read=1038323 bytes_retransmit=0 bytes_invalid=0 send_seq=6517 receive_seq=6517 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998642 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=43.8 th1: temp=45.2 th2: temp=50.1 th3: temp=48.6 sysload=0.18 cputime=204.777 memavail=7397608 print_time=2329.112 buffer_time=2.180 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 117 Hz
Stats 2305.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18423196 bytes_read=2256248 bytes_retransmit=9 bytes_invalid=0 send_seq=320630 receive_seq=320630 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015885 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14692 bytes_read=47275 bytes_retransmit=0 bytes_invalid=0 send_seq=2420 receive_seq=2420 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999259 adj=49997210 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98176 bytes_read=3043730 bytes_retransmit=9 bytes_invalid=0 send_seq=13188 receive_seq=13188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997617 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41848 bytes_read=654240 bytes_retransmit=9 bytes_invalid=0 send_seq=5228 receive_seq=5228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997502 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14905 bytes_read=585174 bytes_retransmit=9 bytes_invalid=0 send_seq=2430 receive_seq=2430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997610 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15445 bytes_read=46360 bytes_retransmit=9 bytes_invalid=0 send_seq=2421 receive_seq=2421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64017 bytes_read=1038679 bytes_retransmit=0 bytes_invalid=0 send_seq=6518 receive_seq=6518 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998674 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.8 th1: temp=45.5 th2: temp=50.3 th3: temp=48.7 sysload=0.18 cputime=204.877 memavail=7396892 print_time=2329.978 buffer_time=2.045 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 118 Hz
Stats 2306.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18428088 bytes_read=2257027 bytes_retransmit=9 bytes_invalid=0 send_seq=320727 receive_seq=320718 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015887 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14698 bytes_read=47291 bytes_retransmit=0 bytes_invalid=0 send_seq=2421 receive_seq=2421 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999259 adj=49997193 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98245 bytes_read=3046838 bytes_retransmit=9 bytes_invalid=0 send_seq=13198 receive_seq=13198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997606 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41854 bytes_read=654340 bytes_retransmit=9 bytes_invalid=0 send_seq=5229 receive_seq=5229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997596 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14911 bytes_read=585392 bytes_retransmit=9 bytes_invalid=0 send_seq=2431 receive_seq=2431 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997597 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15451 bytes_read=46376 bytes_retransmit=9 bytes_invalid=0 send_seq=2422 receive_seq=2422 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64023 bytes_read=1039051 bytes_retransmit=0 bytes_invalid=0 send_seq=6519 receive_seq=6519 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998720 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=43.9 th1: temp=45.2 th2: temp=50.1 th3: temp=48.6 sysload=0.18 cputime=204.990 memavail=7396904 print_time=2331.187 buffer_time=2.247 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Testing frequency 119 Hz
Stats 2307.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18432346 bytes_read=2257795 bytes_retransmit=9 bytes_invalid=0 send_seq=320810 receive_seq=320810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015877 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14704 bytes_read=47307 bytes_retransmit=0 bytes_invalid=0 send_seq=2422 receive_seq=2422 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999259 adj=49997216 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98321 bytes_read=3049895 bytes_retransmit=9 bytes_invalid=0 send_seq=13209 receive_seq=13209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997623 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41860 bytes_read=654454 bytes_retransmit=9 bytes_invalid=0 send_seq=5230 receive_seq=5230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14917 bytes_read=585610 bytes_retransmit=9 bytes_invalid=0 send_seq=2432 receive_seq=2432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997605 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15457 bytes_read=46403 bytes_retransmit=9 bytes_invalid=0 send_seq=2423 receive_seq=2423 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64029 bytes_read=1039391 bytes_retransmit=0 bytes_invalid=0 send_seq=6520 receive_seq=6520 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998698 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=43.7 th1: temp=45.6 th2: temp=50.3 th3: temp=48.6 sysload=0.17 cputime=205.093 memavail=7396904 print_time=2332.116 buffer_time=2.176 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 120 Hz
Stats 2308.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18435637 bytes_read=2258457 bytes_retransmit=9 bytes_invalid=0 send_seq=320881 receive_seq=320881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016050 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14710 bytes_read=47323 bytes_retransmit=0 bytes_invalid=0 send_seq=2423 receive_seq=2423 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999259 adj=49997238 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98397 bytes_read=3052981 bytes_retransmit=9 bytes_invalid=0 send_seq=13220 receive_seq=13220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997644 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41866 bytes_read=654582 bytes_retransmit=9 bytes_invalid=0 send_seq=5231 receive_seq=5231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000072 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14923 bytes_read=585899 bytes_retransmit=9 bytes_invalid=0 send_seq=2433 receive_seq=2433 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15463 bytes_read=46419 bytes_retransmit=9 bytes_invalid=0 send_seq=2424 receive_seq=2424 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999453 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64035 bytes_read=1039747 bytes_retransmit=0 bytes_invalid=0 send_seq=6521 receive_seq=6521 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998691 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=44.2 th1: temp=45.1 th2: temp=50.4 th3: temp=48.7 sysload=0.17 cputime=205.199 memavail=7396912 print_time=2332.983 buffer_time=2.043 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 121 Hz
Stats 2309.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18440573 bytes_read=2259281 bytes_retransmit=9 bytes_invalid=0 send_seq=320978 receive_seq=320978 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=0 freq=400016212 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14716 bytes_read=47352 bytes_retransmit=0 bytes_invalid=0 send_seq=2424 receive_seq=2424 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49996959 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98473 bytes_read=3056037 bytes_retransmit=9 bytes_invalid=0 send_seq=13231 receive_seq=13231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997285 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41872 bytes_read=654682 bytes_retransmit=9 bytes_invalid=0 send_seq=5232 receive_seq=5232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997401 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14929 bytes_read=586133 bytes_retransmit=9 bytes_invalid=0 send_seq=2434 receive_seq=2434 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997355 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15469 bytes_read=46435 bytes_retransmit=9 bytes_invalid=0 send_seq=2425 receive_seq=2425 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999382 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64041 bytes_read=1040103 bytes_retransmit=0 bytes_invalid=0 send_seq=6522 receive_seq=6522 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998495 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=44.0 th1: temp=45.3 th2: temp=50.5 th3: temp=48.7 sysload=0.17 cputime=205.314 memavail=7396912 print_time=2334.191 buffer_time=2.250 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 122 Hz
Stats 2310.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18444909 bytes_read=2260042 bytes_retransmit=9 bytes_invalid=0 send_seq=321065 receive_seq=321065 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400016196 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14722 bytes_read=47368 bytes_retransmit=0 bytes_invalid=0 send_seq=2425 receive_seq=2425 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49996801 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98549 bytes_read=3059094 bytes_retransmit=9 bytes_invalid=0 send_seq=13242 receive_seq=13242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997102 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41878 bytes_read=654782 bytes_retransmit=9 bytes_invalid=0 send_seq=5233 receive_seq=5233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997113 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14935 bytes_read=586382 bytes_retransmit=9 bytes_invalid=0 send_seq=2435 receive_seq=2435 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997207 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15475 bytes_read=46451 bytes_retransmit=9 bytes_invalid=0 send_seq=2426 receive_seq=2426 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999341 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64047 bytes_read=1040459 bytes_retransmit=0 bytes_invalid=0 send_seq=6523 receive_seq=6523 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998383 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=44.1 th1: temp=45.3 th2: temp=50.3 th3: temp=48.6 sysload=0.17 cputime=205.419 memavail=7396912 print_time=2335.115 buffer_time=2.173 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 123 Hz
Stats 2311.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18448259 bytes_read=2260712 bytes_retransmit=9 bytes_invalid=0 send_seq=321137 receive_seq=321137 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016174 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14728 bytes_read=47384 bytes_retransmit=0 bytes_invalid=0 send_seq=2426 receive_seq=2426 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49996881 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98625 bytes_read=3062253 bytes_retransmit=9 bytes_invalid=0 send_seq=13253 receive_seq=13253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997196 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41884 bytes_read=654910 bytes_retransmit=9 bytes_invalid=0 send_seq=5234 receive_seq=5234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997177 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14941 bytes_read=586676 bytes_retransmit=9 bytes_invalid=0 send_seq=2436 receive_seq=2436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997275 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15481 bytes_read=46467 bytes_retransmit=9 bytes_invalid=0 send_seq=2427 receive_seq=2427 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999357 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64053 bytes_read=1040815 bytes_retransmit=0 bytes_invalid=0 send_seq=6524 receive_seq=6524 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998428 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.0 th1: temp=45.3 th2: temp=50.4 th3: temp=48.5 sysload=0.17 cputime=205.523 memavail=7396916 print_time=2335.984 buffer_time=2.042 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 124 Hz
Stats 2312.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18453260 bytes_read=2261546 bytes_retransmit=9 bytes_invalid=0 send_seq=321236 receive_seq=321236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=0 freq=400016165 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14734 bytes_read=47400 bytes_retransmit=0 bytes_invalid=0 send_seq=2427 receive_seq=2427 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49996928 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98701 bytes_read=3065309 bytes_retransmit=9 bytes_invalid=0 send_seq=13264 receive_seq=13264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997275 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41890 bytes_read=655010 bytes_retransmit=9 bytes_invalid=0 send_seq=5235 receive_seq=5235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997222 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14947 bytes_read=586910 bytes_retransmit=9 bytes_invalid=0 send_seq=2437 receive_seq=2437 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997363 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15487 bytes_read=46494 bytes_retransmit=9 bytes_invalid=0 send_seq=2428 receive_seq=2428 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999372 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64059 bytes_read=1041171 bytes_retransmit=0 bytes_invalid=0 send_seq=6525 receive_seq=6525 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998468 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.9 th1: temp=45.3 th2: temp=50.2 th3: temp=48.7 sysload=0.15 cputime=205.640 memavail=7396928 print_time=2337.191 buffer_time=2.248 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 125 Hz
Stats 2313.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18457615 bytes_read=2262281 bytes_retransmit=9 bytes_invalid=0 send_seq=321321 receive_seq=321321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=0 freq=400016147 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14740 bytes_read=47416 bytes_retransmit=0 bytes_invalid=0 send_seq=2428 receive_seq=2428 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997015 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98777 bytes_read=3068365 bytes_retransmit=9 bytes_invalid=0 send_seq=13275 receive_seq=13275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997395 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41896 bytes_read=655124 bytes_retransmit=9 bytes_invalid=0 send_seq=5236 receive_seq=5236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997286 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14953 bytes_read=587144 bytes_retransmit=9 bytes_invalid=0 send_seq=2438 receive_seq=2438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997448 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15493 bytes_read=46510 bytes_retransmit=9 bytes_invalid=0 send_seq=2429 receive_seq=2429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999393 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64065 bytes_read=1041527 bytes_retransmit=0 bytes_invalid=0 send_seq=6526 receive_seq=6526 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998516 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.8 th1: temp=45.6 th2: temp=50.5 th3: temp=48.7 sysload=0.15 cputime=205.766 memavail=7396680 print_time=2338.121 buffer_time=2.177 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Testing frequency 126 Hz
Stats 2314.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18461006 bytes_read=2262951 bytes_retransmit=9 bytes_invalid=0 send_seq=321393 receive_seq=321393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016135 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14746 bytes_read=47445 bytes_retransmit=0 bytes_invalid=0 send_seq=2429 receive_seq=2429 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997059 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98853 bytes_read=3071450 bytes_retransmit=9 bytes_invalid=0 send_seq=13286 receive_seq=13286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997471 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41902 bytes_read=655252 bytes_retransmit=9 bytes_invalid=0 send_seq=5237 receive_seq=5237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997318 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=14959 bytes_read=587438 bytes_retransmit=9 bytes_invalid=0 send_seq=2439 receive_seq=2439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997492 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15499 bytes_read=46526 bytes_retransmit=9 bytes_invalid=0 send_seq=2430 receive_seq=2430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999403 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64071 bytes_read=1041883 bytes_retransmit=0 bytes_invalid=0 send_seq=6527 receive_seq=6527 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998545 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.8 th1: temp=45.3 th2: temp=50.3 th3: temp=48.6 sysload=0.15 cputime=205.874 memavail=7396680 print_time=2338.990 buffer_time=2.046 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 127 Hz
Stats 2315.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18466010 bytes_read=2263796 bytes_retransmit=9 bytes_invalid=0 send_seq=321491 receive_seq=321491 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=0 freq=400016106 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14752 bytes_read=47461 bytes_retransmit=0 bytes_invalid=0 send_seq=2430 receive_seq=2430 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997087 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98929 bytes_read=3074506 bytes_retransmit=9 bytes_invalid=0 send_seq=13297 receive_seq=13297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997510 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41908 bytes_read=655352 bytes_retransmit=9 bytes_invalid=0 send_seq=5238 receive_seq=5238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997339 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14965 bytes_read=587687 bytes_retransmit=9 bytes_invalid=0 send_seq=2440 receive_seq=2440 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997515 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15505 bytes_read=46542 bytes_retransmit=9 bytes_invalid=0 send_seq=2431 receive_seq=2431 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999409 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64077 bytes_read=1042239 bytes_retransmit=0 bytes_invalid=0 send_seq=6528 receive_seq=6528 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998562 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.1 th1: temp=45.4 th2: temp=50.3 th3: temp=48.6 sysload=0.15 cputime=205.999 memavail=7396440 print_time=2340.194 buffer_time=2.250 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 128 Hz
Stats 2316.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18470491 bytes_read=2264551 bytes_retransmit=9 bytes_invalid=0 send_seq=321580 receive_seq=321580 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=16 freq=400016100 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14758 bytes_read=47477 bytes_retransmit=0 bytes_invalid=0 send_seq=2431 receive_seq=2431 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997164 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99005 bytes_read=3077582 bytes_retransmit=9 bytes_invalid=0 send_seq=13308 receive_seq=13308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997596 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41914 bytes_read=655452 bytes_retransmit=9 bytes_invalid=0 send_seq=5239 receive_seq=5239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997431 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14971 bytes_read=587921 bytes_retransmit=9 bytes_invalid=0 send_seq=2441 receive_seq=2441 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997582 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15511 bytes_read=46558 bytes_retransmit=9 bytes_invalid=0 send_seq=2432 receive_seq=2432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64083 bytes_read=1042595 bytes_retransmit=0 bytes_invalid=0 send_seq=6529 receive_seq=6529 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998607 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=43.9 th1: temp=45.4 th2: temp=50.6 th3: temp=48.6 sysload=0.15 cputime=206.106 memavail=7396440 print_time=2341.122 buffer_time=2.177 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 129 Hz
Stats 2317.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18473902 bytes_read=2265237 bytes_retransmit=9 bytes_invalid=0 send_seq=321653 receive_seq=321653 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016054 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14770 bytes_read=47509 bytes_retransmit=0 bytes_invalid=0 send_seq=2433 receive_seq=2433 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997180 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99087 bytes_read=3080686 bytes_retransmit=9 bytes_invalid=0 send_seq=13320 receive_seq=13320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997807 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41926 bytes_read=655596 bytes_retransmit=9 bytes_invalid=0 send_seq=5241 receive_seq=5241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997423 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14983 bytes_read=588231 bytes_retransmit=9 bytes_invalid=0 send_seq=2443 receive_seq=2443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997599 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15523 bytes_read=46601 bytes_retransmit=9 bytes_invalid=0 send_seq=2434 receive_seq=2434 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999923 adj=11999463 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64095 bytes_read=1042967 bytes_retransmit=0 bytes_invalid=0 send_seq=6531 receive_seq=6531 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998607 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.1 th1: temp=45.3 th2: temp=50.4 th3: temp=48.8 sysload=0.14 cputime=206.213 memavail=7396444 print_time=2341.999 buffer_time=2.054 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 130 Hz
Stats 2318.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18478976 bytes_read=2266066 bytes_retransmit=9 bytes_invalid=0 send_seq=321752 receive_seq=321752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016265 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14776 bytes_read=47525 bytes_retransmit=0 bytes_invalid=0 send_seq=2434 receive_seq=2434 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997239 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99163 bytes_read=3083744 bytes_retransmit=9 bytes_invalid=0 send_seq=13331 receive_seq=13331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997859 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41932 bytes_read=655710 bytes_retransmit=9 bytes_invalid=0 send_seq=5242 receive_seq=5242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997479 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14989 bytes_read=588465 bytes_retransmit=9 bytes_invalid=0 send_seq=2444 receive_seq=2444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15529 bytes_read=46617 bytes_retransmit=9 bytes_invalid=0 send_seq=2435 receive_seq=2435 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999923 adj=11999497 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64101 bytes_read=1043323 bytes_retransmit=0 bytes_invalid=0 send_seq=6532 receive_seq=6532 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998663 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=44.0 th1: temp=45.4 th2: temp=50.0 th3: temp=48.7 sysload=0.14 cputime=206.333 memavail=7396444 print_time=2343.198 buffer_time=2.252 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 131 Hz
Stats 2319.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18483317 bytes_read=2266816 bytes_retransmit=9 bytes_invalid=0 send_seq=321840 receive_seq=321840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=64 freq=400016224 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14782 bytes_read=47554 bytes_retransmit=0 bytes_invalid=0 send_seq=2435 receive_seq=2435 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49996926 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99232 bytes_read=3086835 bytes_retransmit=9 bytes_invalid=0 send_seq=13341 receive_seq=13341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997391 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41938 bytes_read=655810 bytes_retransmit=9 bytes_invalid=0 send_seq=5243 receive_seq=5243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997119 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=14995 bytes_read=588699 bytes_retransmit=9 bytes_invalid=0 send_seq=2445 receive_seq=2445 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997348 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15535 bytes_read=46633 bytes_retransmit=9 bytes_invalid=0 send_seq=2436 receive_seq=2436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999404 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64107 bytes_read=1043679 bytes_retransmit=0 bytes_invalid=0 send_seq=6533 receive_seq=6533 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998452 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=44.2 th1: temp=45.5 th2: temp=50.4 th3: temp=48.8 sysload=0.14 cputime=206.440 memavail=7396448 print_time=2344.123 buffer_time=2.177 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 132 Hz
Stats 2320.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18486884 bytes_read=2267522 bytes_retransmit=9 bytes_invalid=0 send_seq=321916 receive_seq=321916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016189 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14788 bytes_read=47570 bytes_retransmit=0 bytes_invalid=0 send_seq=2436 receive_seq=2436 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997025 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99308 bytes_read=3089919 bytes_retransmit=9 bytes_invalid=0 send_seq=13352 receive_seq=13352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997493 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41944 bytes_read=655938 bytes_retransmit=9 bytes_invalid=0 send_seq=5244 receive_seq=5244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997221 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15001 bytes_read=589008 bytes_retransmit=9 bytes_invalid=0 send_seq=2446 receive_seq=2446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997476 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15541 bytes_read=46649 bytes_retransmit=9 bytes_invalid=0 send_seq=2437 receive_seq=2437 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999422 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64113 bytes_read=1044035 bytes_retransmit=0 bytes_invalid=0 send_seq=6534 receive_seq=6534 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998511 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=44.1 th1: temp=45.4 th2: temp=50.6 th3: temp=48.8 sysload=0.14 cputime=206.548 memavail=7396448 print_time=2344.999 buffer_time=2.052 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Stats 2321.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18491658 bytes_read=2268321 bytes_retransmit=9 bytes_invalid=0 send_seq=322008 receive_seq=322008 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016194 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14794 bytes_read=47586 bytes_retransmit=0 bytes_invalid=0 send_seq=2437 receive_seq=2437 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997112 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99384 bytes_read=3092995 bytes_retransmit=9 bytes_invalid=0 send_seq=13363 receive_seq=13363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997762 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41950 bytes_read=656038 bytes_retransmit=9 bytes_invalid=0 send_seq=5245 receive_seq=5245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997296 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15007 bytes_read=589242 bytes_retransmit=9 bytes_invalid=0 send_seq=2447 receive_seq=2447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997531 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15547 bytes_read=46665 bytes_retransmit=9 bytes_invalid=0 send_seq=2438 receive_seq=2438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999436 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64119 bytes_read=1044391 bytes_retransmit=0 bytes_invalid=0 send_seq=6535 receive_seq=6535 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998559 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=44.0 th1: temp=45.7 th2: temp=50.3 th3: temp=48.8 sysload=0.14 cputime=206.673 memavail=7396836 print_time=2345.976 buffer_time=2.029 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2322.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18491956 bytes_read=2268746 bytes_retransmit=9 bytes_invalid=0 send_seq=322031 receive_seq=322031 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016158 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14800 bytes_read=47602 bytes_retransmit=0 bytes_invalid=0 send_seq=2438 receive_seq=2438 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997144 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99460 bytes_read=3096052 bytes_retransmit=9 bytes_invalid=0 send_seq=13374 receive_seq=13374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997709 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41956 bytes_read=656138 bytes_retransmit=9 bytes_invalid=0 send_seq=5246 receive_seq=5246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997301 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15013 bytes_read=589476 bytes_retransmit=9 bytes_invalid=0 send_seq=2448 receive_seq=2448 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997531 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15553 bytes_read=46692 bytes_retransmit=9 bytes_invalid=0 send_seq=2439 receive_seq=2439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999429 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64125 bytes_read=1044747 bytes_retransmit=0 bytes_invalid=0 send_seq=6536 receive_seq=6536 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998570 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=44.4 th1: temp=45.5 th2: temp=50.7 th3: temp=48.7 sysload=0.13 cputime=206.735 memavail=7396836 print_time=2345.976 buffer_time=1.028 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2323.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18492254 bytes_read=2269185 bytes_retransmit=9 bytes_invalid=0 send_seq=322054 receive_seq=322054 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016124 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14806 bytes_read=47618 bytes_retransmit=0 bytes_invalid=0 send_seq=2439 receive_seq=2439 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997234 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99536 bytes_read=3099137 bytes_retransmit=9 bytes_invalid=0 send_seq=13385 receive_seq=13385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997753 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41962 bytes_read=656280 bytes_retransmit=9 bytes_invalid=0 send_seq=5247 receive_seq=5247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997352 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15019 bytes_read=589770 bytes_retransmit=9 bytes_invalid=0 send_seq=2449 receive_seq=2449 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997584 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15559 bytes_read=46708 bytes_retransmit=9 bytes_invalid=0 send_seq=2440 receive_seq=2440 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64131 bytes_read=1045103 bytes_retransmit=0 bytes_invalid=0 send_seq=6537 receive_seq=6537 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998605 coil_temp=17.6 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=44.6 th1: temp=45.8 th2: temp=50.2 th3: temp=48.7 sysload=0.13 cputime=206.798 memavail=7396836 print_time=2345.976 buffer_time=0.028 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Writing raw accelerometer data to /tmp/raw_data_x_toolboard_t0_t0.csv file
RatOS | IDEX:: Selecting T1..
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 20.000000
RatOS | IDEX:: Toolhead offset applied for T1: X=-0.0 Y=-0.0 Z=-0.0
Activating extruder extruder1
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
Probing point (557.600, 250.000, 20.000)
LIS2DW finished 'toolboard_t0' measurements
Stats 2324.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18494487 bytes_read=2269780 bytes_retransmit=9 bytes_invalid=0 send_seq=322108 receive_seq=322108 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016088 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14812 bytes_read=47647 bytes_retransmit=0 bytes_invalid=0 send_seq=2440 receive_seq=2440 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997272 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99604 bytes_read=3099793 bytes_retransmit=9 bytes_invalid=0 send_seq=13393 receive_seq=13393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997801 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=41968 bytes_read=656380 bytes_retransmit=9 bytes_invalid=0 send_seq=5248 receive_seq=5248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997403 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15025 bytes_read=590004 bytes_retransmit=9 bytes_invalid=0 send_seq=2450 receive_seq=2450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15565 bytes_read=46724 bytes_retransmit=9 bytes_invalid=0 send_seq=2441 receive_seq=2441 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64137 bytes_read=1045459 bytes_retransmit=0 bytes_invalid=0 send_seq=6538 receive_seq=6538 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998675 coil_temp=17.6 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=44.4 th1: temp=45.4 th2: temp=50.4 th3: temp=48.9 sysload=0.13 cputime=206.956 memavail=7399036 print_time=2347.250 buffer_time=0.302 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t1' measurements
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t0' measurements
toolhead: max_velocity: 600.000000
max_accel: 8379.841000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance testing
Testing frequency 10 Hz
Testing frequency 11 Hz
Testing frequency 12 Hz
Stats 2325.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18503658 bytes_read=2270951 bytes_retransmit=9 bytes_invalid=0 send_seq=322277 receive_seq=322277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=395 freq=400016053 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14818 bytes_read=47663 bytes_retransmit=0 bytes_invalid=0 send_seq=2441 receive_seq=2441 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997349 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99759 bytes_read=3101791 bytes_retransmit=9 bytes_invalid=0 send_seq=13411 receive_seq=13411 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997849 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=42123 bytes_read=658378 bytes_retransmit=9 bytes_invalid=0 send_seq=5266 receive_seq=5266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997484 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15031 bytes_read=590253 bytes_retransmit=9 bytes_invalid=0 send_seq=2451 receive_seq=2451 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997709 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15571 bytes_read=46740 bytes_retransmit=9 bytes_invalid=0 send_seq=2442 receive_seq=2442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999477 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64143 bytes_read=1045815 bytes_retransmit=0 bytes_invalid=0 send_seq=6539 receive_seq=6539 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998756 coil_temp=17.6 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=44.2 th1: temp=45.5 th2: temp=50.2 th3: temp=48.8 sysload=0.13 cputime=207.160 memavail=7398820 print_time=2350.441 buffer_time=2.492 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2326.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18506927 bytes_read=2271610 bytes_retransmit=9 bytes_invalid=0 send_seq=322344 receive_seq=322344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400016046 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14824 bytes_read=47679 bytes_retransmit=0 bytes_invalid=0 send_seq=2442 receive_seq=2442 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997315 toolboard_t0: mcu_awake=0.242 mcu_task_avg=0.000115 mcu_task_stddev=0.000070 bytes_write=99835 bytes_read=3104818 bytes_retransmit=9 bytes_invalid=0 send_seq=13422 receive_seq=13422 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997712 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=42199 bytes_read=661388 bytes_retransmit=9 bytes_invalid=0 send_seq=5277 receive_seq=5277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15037 bytes_read=590547 bytes_retransmit=9 bytes_invalid=0 send_seq=2452 receive_seq=2452 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15577 bytes_read=46756 bytes_retransmit=9 bytes_invalid=0 send_seq=2443 receive_seq=2443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999453 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64149 bytes_read=1046171 bytes_retransmit=0 bytes_invalid=0 send_seq=6540 receive_seq=6540 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998675 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=44.0 th1: temp=45.3 th2: temp=50.6 th3: temp=48.8 sysload=0.13 cputime=207.250 memavail=7398604 print_time=2351.034 buffer_time=2.086 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 13 Hz
Testing frequency 14 Hz
Stats 2327.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18511411 bytes_read=2272375 bytes_retransmit=9 bytes_invalid=0 send_seq=322432 receive_seq=322432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=1165 freq=400016050 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14830 bytes_read=47694 bytes_retransmit=0 bytes_invalid=0 send_seq=2443 receive_seq=2443 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997323 toolboard_t0: mcu_awake=0.242 mcu_task_avg=0.000115 mcu_task_stddev=0.000070 bytes_write=99911 bytes_read=3107835 bytes_retransmit=9 bytes_invalid=0 send_seq=13433 receive_seq=13433 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997724 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=42275 bytes_read=664403 bytes_retransmit=9 bytes_invalid=0 send_seq=5288 receive_seq=5288 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997556 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15043 bytes_read=590781 bytes_retransmit=9 bytes_invalid=0 send_seq=2453 receive_seq=2453 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15583 bytes_read=46783 bytes_retransmit=9 bytes_invalid=0 send_seq=2444 receive_seq=2444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64155 bytes_read=1046527 bytes_retransmit=0 bytes_invalid=0 send_seq=6541 receive_seq=6541 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998675 coil_temp=17.6 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=44.2 th1: temp=45.8 th2: temp=50.6 th3: temp=48.8 sysload=0.20 cputime=207.356 memavail=7398604 print_time=2352.306 buffer_time=2.357 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 15 Hz
Stats 2328.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18516247 bytes_read=2273155 bytes_retransmit=9 bytes_invalid=0 send_seq=322526 receive_seq=322526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=344 freq=400016037 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14836 bytes_read=47709 bytes_retransmit=0 bytes_invalid=0 send_seq=2444 receive_seq=2444 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997291 toolboard_t0: mcu_awake=0.242 mcu_task_avg=0.000115 mcu_task_stddev=0.000070 bytes_write=99980 bytes_read=3110865 bytes_retransmit=9 bytes_invalid=0 send_seq=13443 receive_seq=13443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997680 toolboard_t1: mcu_awake=0.184 mcu_task_avg=0.000112 mcu_task_stddev=0.000071 bytes_write=42351 bytes_read=667459 bytes_retransmit=9 bytes_invalid=0 send_seq=5299 receive_seq=5299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997518 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15049 bytes_read=591030 bytes_retransmit=9 bytes_invalid=0 send_seq=2454 receive_seq=2454 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15589 bytes_read=46799 bytes_retransmit=9 bytes_invalid=0 send_seq=2445 receive_seq=2445 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999444 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64161 bytes_read=1046883 bytes_retransmit=0 bytes_invalid=0 send_seq=6542 receive_seq=6542 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998653 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.6 th1: temp=45.7 th2: temp=50.4 th3: temp=48.7 sysload=0.20 cputime=207.460 memavail=7398612 print_time=2353.161 buffer_time=2.211 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 16 Hz
Stats 2329.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=18520286 bytes_read=2273872 bytes_retransmit=9 bytes_invalid=0 send_seq=322606 receive_seq=322606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=1432 freq=400016050 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14842 bytes_read=47737 bytes_retransmit=0 bytes_invalid=0 send_seq=2445 receive_seq=2445 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997298 toolboard_t0: mcu_awake=0.242 mcu_task_avg=0.000115 mcu_task_stddev=0.000070 bytes_write=100056 bytes_read=3113927 bytes_retransmit=9 bytes_invalid=0 send_seq=13454 receive_seq=13454 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997680 toolboard_t1: mcu_awake=0.184 mcu_task_avg=0.000112 mcu_task_stddev=0.000071 bytes_write=42420 bytes_read=670568 bytes_retransmit=9 bytes_invalid=0 send_seq=5309 receive_seq=5309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997522 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15055 bytes_read=591309 bytes_retransmit=9 bytes_invalid=0 send_seq=2455 receive_seq=2455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15595 bytes_read=46815 bytes_retransmit=9 bytes_invalid=0 send_seq=2446 receive_seq=2446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64167 bytes_read=1047239 bytes_retransmit=0 bytes_invalid=0 send_seq=6543 receive_seq=6543 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998733 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.4 th1: temp=45.6 th2: temp=50.4 th3: temp=48.8 sysload=0.20 cputime=207.563 memavail=7398612 print_time=2354.126 buffer_time=2.176 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2330.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18525525 bytes_read=2274713 bytes_retransmit=9 bytes_invalid=0 send_seq=322706 receive_seq=322706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=472 freq=400016022 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14848 bytes_read=47752 bytes_retransmit=0 bytes_invalid=0 send_seq=2446 receive_seq=2446 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997255 toolboard_t0: mcu_awake=0.242 mcu_task_avg=0.000115 mcu_task_stddev=0.000070 bytes_write=100132 bytes_read=3117042 bytes_retransmit=9 bytes_invalid=0 send_seq=13465 receive_seq=13465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997633 toolboard_t1: mcu_awake=0.184 mcu_task_avg=0.000112 mcu_task_stddev=0.000071 bytes_write=42496 bytes_read=673625 bytes_retransmit=9 bytes_invalid=0 send_seq=5320 receive_seq=5320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997478 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15061 bytes_read=591558 bytes_retransmit=9 bytes_invalid=0 send_seq=2456 receive_seq=2456 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15601 bytes_read=46831 bytes_retransmit=9 bytes_invalid=0 send_seq=2447 receive_seq=2447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64173 bytes_read=1047595 bytes_retransmit=0 bytes_invalid=0 send_seq=6544 receive_seq=6544 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998733 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=44.4 th1: temp=45.5 th2: temp=50.3 th3: temp=48.6 sysload=0.20 cputime=207.668 memavail=7398612 print_time=2355.007 buffer_time=2.056 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 17 Hz
Testing frequency 18 Hz
Stats 2331.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18530578 bytes_read=2275503 bytes_retransmit=9 bytes_invalid=0 send_seq=322802 receive_seq=322802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=2048 freq=400016000 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14854 bytes_read=47767 bytes_retransmit=0 bytes_invalid=0 send_seq=2447 receive_seq=2447 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997287 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100208 bytes_read=3120130 bytes_retransmit=9 bytes_invalid=0 send_seq=13476 receive_seq=13476 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997675 toolboard_t1: mcu_awake=0.184 mcu_task_avg=0.000112 mcu_task_stddev=0.000071 bytes_write=42572 bytes_read=676683 bytes_retransmit=9 bytes_invalid=0 send_seq=5331 receive_seq=5331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997605 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15067 bytes_read=591807 bytes_retransmit=9 bytes_invalid=0 send_seq=2457 receive_seq=2457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15607 bytes_read=46847 bytes_retransmit=9 bytes_invalid=0 send_seq=2448 receive_seq=2448 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999445 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64179 bytes_read=1047951 bytes_retransmit=0 bytes_invalid=0 send_seq=6545 receive_seq=6545 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998805 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=44.8 th1: temp=45.7 th2: temp=50.5 th3: temp=48.7 sysload=0.20 cputime=207.783 memavail=7398612 print_time=2356.275 buffer_time=2.324 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Testing frequency 19 Hz
Stats 2332.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18535398 bytes_read=2276282 bytes_retransmit=9 bytes_invalid=0 send_seq=322893 receive_seq=322893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=2548 freq=400015984 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14860 bytes_read=47782 bytes_retransmit=0 bytes_invalid=0 send_seq=2448 receive_seq=2448 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997296 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100284 bytes_read=3123202 bytes_retransmit=9 bytes_invalid=0 send_seq=13487 receive_seq=13487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997689 toolboard_t1: mcu_awake=0.184 mcu_task_avg=0.000112 mcu_task_stddev=0.000071 bytes_write=42648 bytes_read=679767 bytes_retransmit=9 bytes_invalid=0 send_seq=5342 receive_seq=5342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997586 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15073 bytes_read=592086 bytes_retransmit=9 bytes_invalid=0 send_seq=2458 receive_seq=2458 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15613 bytes_read=46874 bytes_retransmit=9 bytes_invalid=0 send_seq=2449 receive_seq=2449 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64185 bytes_read=1048307 bytes_retransmit=0 bytes_invalid=0 send_seq=6546 receive_seq=6546 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998758 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.8 th1: temp=45.7 th2: temp=50.2 th3: temp=48.5 sysload=0.18 cputime=207.887 memavail=7398612 print_time=2357.096 buffer_time=2.144 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 20 Hz
Stats 2333.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18541247 bytes_read=2277147 bytes_retransmit=9 bytes_invalid=0 send_seq=323001 receive_seq=323001 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=20 upcoming_bytes=1962 freq=400015961 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14866 bytes_read=47798 bytes_retransmit=0 bytes_invalid=0 send_seq=2449 receive_seq=2449 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997327 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100360 bytes_read=3126260 bytes_retransmit=9 bytes_invalid=0 send_seq=13498 receive_seq=13498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997702 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=42724 bytes_read=682842 bytes_retransmit=9 bytes_invalid=0 send_seq=5353 receive_seq=5353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997592 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15079 bytes_read=592320 bytes_retransmit=9 bytes_invalid=0 send_seq=2459 receive_seq=2459 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997698 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15619 bytes_read=46890 bytes_retransmit=9 bytes_invalid=0 send_seq=2450 receive_seq=2450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64191 bytes_read=1048663 bytes_retransmit=0 bytes_invalid=0 send_seq=6547 receive_seq=6547 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998750 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.8 th1: temp=45.5 th2: temp=50.3 th3: temp=48.5 sysload=0.18 cputime=207.997 memavail=7398612 print_time=2358.081 buffer_time=2.129 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2334.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=18547178 bytes_read=2278007 bytes_retransmit=9 bytes_invalid=0 send_seq=323111 receive_seq=323111 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=1896 freq=400015961 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14872 bytes_read=47827 bytes_retransmit=0 bytes_invalid=0 send_seq=2450 receive_seq=2450 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997359 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100436 bytes_read=3129334 bytes_retransmit=9 bytes_invalid=0 send_seq=13509 receive_seq=13509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997766 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=42800 bytes_read=685898 bytes_retransmit=9 bytes_invalid=0 send_seq=5364 receive_seq=5364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997666 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15085 bytes_read=592569 bytes_retransmit=9 bytes_invalid=0 send_seq=2460 receive_seq=2460 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997715 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15625 bytes_read=46906 bytes_retransmit=9 bytes_invalid=0 send_seq=2451 receive_seq=2451 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999454 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64197 bytes_read=1049019 bytes_retransmit=0 bytes_invalid=0 send_seq=6548 receive_seq=6548 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998742 coil_temp=17.6 refs=0 mcu_temp=20.76 supply_voltage=3.012 th0: temp=44.9 th1: temp=45.6 th2: temp=50.1 th3: temp=48.4 sysload=0.18 cputime=208.105 memavail=7398612 print_time=2358.953 buffer_time=2.001 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 21 Hz
Testing frequency 22 Hz
Stats 2335.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18552525 bytes_read=2278842 bytes_retransmit=9 bytes_invalid=0 send_seq=323210 receive_seq=323210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=3756 freq=400015950 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14878 bytes_read=47843 bytes_retransmit=0 bytes_invalid=0 send_seq=2451 receive_seq=2451 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997346 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100512 bytes_read=3132408 bytes_retransmit=9 bytes_invalid=0 send_seq=13520 receive_seq=13520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997737 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=42876 bytes_read=688983 bytes_retransmit=9 bytes_invalid=0 send_seq=5375 receive_seq=5375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997713 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15091 bytes_read=592863 bytes_retransmit=9 bytes_invalid=0 send_seq=2461 receive_seq=2461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997713 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15631 bytes_read=46922 bytes_retransmit=9 bytes_invalid=0 send_seq=2452 receive_seq=2452 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999449 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64203 bytes_read=1049375 bytes_retransmit=0 bytes_invalid=0 send_seq=6549 receive_seq=6549 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998731 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=45.1 th1: temp=45.7 th2: temp=50.6 th3: temp=48.4 sysload=0.18 cputime=208.224 memavail=7398404 print_time=2360.176 buffer_time=2.223 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 23 Hz
Stats 2336.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18558838 bytes_read=2279757 bytes_retransmit=9 bytes_invalid=0 send_seq=323328 receive_seq=323328 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=35 upcoming_bytes=2817 freq=400015965 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14884 bytes_read=47859 bytes_retransmit=0 bytes_invalid=0 send_seq=2452 receive_seq=2452 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997328 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100588 bytes_read=3135482 bytes_retransmit=9 bytes_invalid=0 send_seq=13531 receive_seq=13531 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997717 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=42952 bytes_read=692098 bytes_retransmit=9 bytes_invalid=0 send_seq=5386 receive_seq=5386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997717 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15097 bytes_read=593097 bytes_retransmit=9 bytes_invalid=0 send_seq=2462 receive_seq=2462 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997712 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15637 bytes_read=46938 bytes_retransmit=9 bytes_invalid=0 send_seq=2453 receive_seq=2453 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999449 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64209 bytes_read=1049731 bytes_retransmit=0 bytes_invalid=0 send_seq=6550 receive_seq=6550 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998700 coil_temp=17.6 refs=0 mcu_temp=20.73 supply_voltage=3.012 th0: temp=45.3 th1: temp=45.6 th2: temp=50.2 th3: temp=48.4 sysload=0.18 cputime=208.340 memavail=7397956 print_time=2361.096 buffer_time=2.143 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2337.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18565167 bytes_read=2280657 bytes_retransmit=9 bytes_invalid=0 send_seq=323446 receive_seq=323446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=2944 freq=400015942 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14890 bytes_read=47875 bytes_retransmit=0 bytes_invalid=0 send_seq=2453 receive_seq=2453 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997281 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100664 bytes_read=3138553 bytes_retransmit=9 bytes_invalid=0 send_seq=13542 receive_seq=13542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997673 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43028 bytes_read=695158 bytes_retransmit=9 bytes_invalid=0 send_seq=5397 receive_seq=5397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997643 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15103 bytes_read=593346 bytes_retransmit=9 bytes_invalid=0 send_seq=2463 receive_seq=2463 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15643 bytes_read=46965 bytes_retransmit=9 bytes_invalid=0 send_seq=2454 receive_seq=2454 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64215 bytes_read=1050087 bytes_retransmit=0 bytes_invalid=0 send_seq=6551 receive_seq=6551 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998681 coil_temp=17.6 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=45.7 th1: temp=45.8 th2: temp=49.9 th3: temp=48.3 sysload=0.17 cputime=208.448 memavail=7397956 print_time=2361.981 buffer_time=2.027 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 24 Hz
Testing frequency 25 Hz
Stats 2338.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18570959 bytes_read=2281526 bytes_retransmit=9 bytes_invalid=0 send_seq=323555 receive_seq=323555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=2972 freq=400015935 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14896 bytes_read=47891 bytes_retransmit=0 bytes_invalid=0 send_seq=2454 receive_seq=2454 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997316 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100740 bytes_read=3141682 bytes_retransmit=9 bytes_invalid=0 send_seq=13553 receive_seq=13553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997702 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43104 bytes_read=698259 bytes_retransmit=9 bytes_invalid=0 send_seq=5408 receive_seq=5408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997644 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15109 bytes_read=593625 bytes_retransmit=9 bytes_invalid=0 send_seq=2464 receive_seq=2464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997700 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15649 bytes_read=46981 bytes_retransmit=9 bytes_invalid=0 send_seq=2455 receive_seq=2455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64221 bytes_read=1050443 bytes_retransmit=0 bytes_invalid=0 send_seq=6552 receive_seq=6552 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998693 coil_temp=17.6 refs=0 mcu_temp=20.73 supply_voltage=3.012 th0: temp=45.1 th1: temp=45.7 th2: temp=50.0 th3: temp=48.3 sysload=0.17 cputime=208.577 memavail=7392412 print_time=2362.946 buffer_time=1.991 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 26 Hz
Stats 2339.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18577802 bytes_read=2282469 bytes_retransmit=9 bytes_invalid=0 send_seq=323679 receive_seq=323679 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=4508 freq=400015921 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14902 bytes_read=47920 bytes_retransmit=0 bytes_invalid=0 send_seq=2455 receive_seq=2455 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997324 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100816 bytes_read=3144740 bytes_retransmit=9 bytes_invalid=0 send_seq=13564 receive_seq=13564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997714 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43180 bytes_read=701317 bytes_retransmit=9 bytes_invalid=0 send_seq=5419 receive_seq=5419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997636 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15115 bytes_read=593859 bytes_retransmit=9 bytes_invalid=0 send_seq=2465 receive_seq=2465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997696 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15655 bytes_read=46997 bytes_retransmit=9 bytes_invalid=0 send_seq=2456 receive_seq=2456 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64227 bytes_read=1050799 bytes_retransmit=0 bytes_invalid=0 send_seq=6553 receive_seq=6553 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998684 coil_temp=17.6 refs=0 mcu_temp=20.73 supply_voltage=3.012 th0: temp=45.3 th1: temp=45.9 th2: temp=50.1 th3: temp=48.0 sysload=0.17 cputime=208.698 memavail=7398824 print_time=2364.173 buffer_time=2.217 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2340.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=18584777 bytes_read=2283432 bytes_retransmit=9 bytes_invalid=0 send_seq=323807 receive_seq=323807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=3752 freq=400015929 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14908 bytes_read=47936 bytes_retransmit=0 bytes_invalid=0 send_seq=2456 receive_seq=2456 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997320 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100892 bytes_read=3147810 bytes_retransmit=9 bytes_invalid=0 send_seq=13575 receive_seq=13575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997717 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43256 bytes_read=704388 bytes_retransmit=9 bytes_invalid=0 send_seq=5430 receive_seq=5430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997608 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15121 bytes_read=594123 bytes_retransmit=9 bytes_invalid=0 send_seq=2466 receive_seq=2466 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997750 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15661 bytes_read=47013 bytes_retransmit=9 bytes_invalid=0 send_seq=2457 receive_seq=2457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64233 bytes_read=1051155 bytes_retransmit=0 bytes_invalid=0 send_seq=6554 receive_seq=6554 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998672 coil_temp=17.6 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=45.6 th1: temp=45.6 th2: temp=50.0 th3: temp=48.2 sysload=0.17 cputime=208.808 memavail=7398824 print_time=2365.031 buffer_time=2.075 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 27 Hz
Stats 2341.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=18590838 bytes_read=2284311 bytes_retransmit=9 bytes_invalid=0 send_seq=323915 receive_seq=323915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=4458 freq=400015940 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14914 bytes_read=47952 bytes_retransmit=0 bytes_invalid=0 send_seq=2457 receive_seq=2457 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997291 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100968 bytes_read=3150900 bytes_retransmit=9 bytes_invalid=0 send_seq=13586 receive_seq=13586 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997682 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43332 bytes_read=707459 bytes_retransmit=9 bytes_invalid=0 send_seq=5441 receive_seq=5441 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997577 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15127 bytes_read=594402 bytes_retransmit=9 bytes_invalid=0 send_seq=2467 receive_seq=2467 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997733 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15667 bytes_read=47029 bytes_retransmit=9 bytes_invalid=0 send_seq=2458 receive_seq=2458 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999447 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64239 bytes_read=1051511 bytes_retransmit=0 bytes_invalid=0 send_seq=6555 receive_seq=6555 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998659 coil_temp=17.6 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=45.6 th1: temp=46.1 th2: temp=50.0 th3: temp=48.3 sysload=0.17 cputime=208.919 memavail=7398824 print_time=2366.007 buffer_time=2.049 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Testing frequency 28 Hz
Testing frequency 29 Hz
Stats 2342.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=18598135 bytes_read=2285286 bytes_retransmit=9 bytes_invalid=0 send_seq=324048 receive_seq=324048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=5220 freq=400015937 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14920 bytes_read=47968 bytes_retransmit=0 bytes_invalid=0 send_seq=2458 receive_seq=2458 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997255 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101044 bytes_read=3153957 bytes_retransmit=9 bytes_invalid=0 send_seq=13597 receive_seq=13597 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997644 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43408 bytes_read=710515 bytes_retransmit=9 bytes_invalid=0 send_seq=5452 receive_seq=5452 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15133 bytes_read=594636 bytes_retransmit=9 bytes_invalid=0 send_seq=2468 receive_seq=2468 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997689 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15673 bytes_read=47056 bytes_retransmit=9 bytes_invalid=0 send_seq=2459 receive_seq=2459 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64245 bytes_read=1051867 bytes_retransmit=0 bytes_invalid=0 send_seq=6556 receive_seq=6556 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998638 coil_temp=17.6 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=45.6 th1: temp=46.1 th2: temp=50.1 th3: temp=48.1 sysload=0.15 cputime=209.039 memavail=7398824 print_time=2367.182 buffer_time=2.224 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 30 Hz
Stats 2343.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=18605359 bytes_read=2286241 bytes_retransmit=9 bytes_invalid=0 send_seq=324177 receive_seq=324177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=52 upcoming_bytes=4444 freq=400015929 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=14926 bytes_read=47984 bytes_retransmit=0 bytes_invalid=0 send_seq=2459 receive_seq=2459 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997271 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101120 bytes_read=3157029 bytes_retransmit=9 bytes_invalid=0 send_seq=13608 receive_seq=13608 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997639 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43484 bytes_read=713662 bytes_retransmit=9 bytes_invalid=0 send_seq=5463 receive_seq=5463 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15139 bytes_read=594885 bytes_retransmit=9 bytes_invalid=0 send_seq=2469 receive_seq=2469 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997694 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15679 bytes_read=47072 bytes_retransmit=9 bytes_invalid=0 send_seq=2460 receive_seq=2460 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64251 bytes_read=1052223 bytes_retransmit=0 bytes_invalid=0 send_seq=6557 receive_seq=6557 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998659 coil_temp=17.6 refs=0 mcu_temp=20.73 supply_voltage=3.012 th0: temp=45.8 th1: temp=45.5 th2: temp=50.1 th3: temp=48.0 sysload=0.15 cputime=209.151 memavail=7398824 print_time=2368.063 buffer_time=2.105 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2344.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=18611675 bytes_read=2287165 bytes_retransmit=9 bytes_invalid=0 send_seq=324294 receive_seq=324294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=29 upcoming_bytes=5523 freq=400015930 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=14932 bytes_read=48013 bytes_retransmit=0 bytes_invalid=0 send_seq=2460 receive_seq=2460 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997276 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101196 bytes_read=3160103 bytes_retransmit=9 bytes_invalid=0 send_seq=13619 receive_seq=13619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997651 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43560 bytes_read=716732 bytes_retransmit=9 bytes_invalid=0 send_seq=5474 receive_seq=5474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997501 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15145 bytes_read=595164 bytes_retransmit=9 bytes_invalid=0 send_seq=2470 receive_seq=2470 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997714 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15685 bytes_read=47088 bytes_retransmit=9 bytes_invalid=0 send_seq=2461 receive_seq=2461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64257 bytes_read=1052579 bytes_retransmit=0 bytes_invalid=0 send_seq=6558 receive_seq=6558 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998660 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=45.8 th1: temp=45.8 th2: temp=49.7 th3: temp=48.1 sysload=0.15 cputime=209.264 memavail=7398824 print_time=2369.024 buffer_time=2.064 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 31 Hz
Testing frequency 32 Hz
Stats 2345.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=18619405 bytes_read=2288186 bytes_retransmit=9 bytes_invalid=0 send_seq=324433 receive_seq=324433 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=6399 freq=400015922 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=14938 bytes_read=48029 bytes_retransmit=0 bytes_invalid=0 send_seq=2461 receive_seq=2461 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997271 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101265 bytes_read=3163194 bytes_retransmit=9 bytes_invalid=0 send_seq=13629 receive_seq=13629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997640 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43629 bytes_read=719765 bytes_retransmit=9 bytes_invalid=0 send_seq=5484 receive_seq=5484 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=15151 bytes_read=595413 bytes_retransmit=9 bytes_invalid=0 send_seq=2471 receive_seq=2471 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997696 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15691 bytes_read=47104 bytes_retransmit=9 bytes_invalid=0 send_seq=2462 receive_seq=2462 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64263 bytes_read=1052935 bytes_retransmit=0 bytes_invalid=0 send_seq=6559 receive_seq=6559 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998666 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=45.9 th1: temp=46.0 th2: temp=50.1 th3: temp=48.1 sysload=0.15 cputime=209.386 memavail=7398068 print_time=2370.205 buffer_time=2.245 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 33 Hz
Stats 2346.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=18627202 bytes_read=2289206 bytes_retransmit=9 bytes_invalid=0 send_seq=324575 receive_seq=324575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=5292 freq=400015919 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=14944 bytes_read=48045 bytes_retransmit=0 bytes_invalid=0 send_seq=2462 receive_seq=2462 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997277 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101341 bytes_read=3166281 bytes_retransmit=9 bytes_invalid=0 send_seq=13640 receive_seq=13640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997648 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43705 bytes_read=722835 bytes_retransmit=9 bytes_invalid=0 send_seq=5495 receive_seq=5495 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997499 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=15157 bytes_read=595677 bytes_retransmit=9 bytes_invalid=0 send_seq=2472 receive_seq=2472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15697 bytes_read=47120 bytes_retransmit=9 bytes_invalid=0 send_seq=2463 receive_seq=2463 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64269 bytes_read=1053291 bytes_retransmit=0 bytes_invalid=0 send_seq=6560 receive_seq=6560 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998659 coil_temp=17.6 refs=0 mcu_temp=20.73 supply_voltage=3.012 th0: temp=45.5 th1: temp=46.0 th2: temp=49.8 th3: temp=48.1 sysload=0.15 cputime=209.503 memavail=7398080 print_time=2371.104 buffer_time=2.143 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2347.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=18633907 bytes_read=2290165 bytes_retransmit=9 bytes_invalid=0 send_seq=324699 receive_seq=324699 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=6464 freq=400015916 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=14950 bytes_read=48061 bytes_retransmit=0 bytes_invalid=0 send_seq=2463 receive_seq=2463 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997278 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101417 bytes_read=3169353 bytes_retransmit=9 bytes_invalid=0 send_seq=13651 receive_seq=13651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997645 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43781 bytes_read=725905 bytes_retransmit=9 bytes_invalid=0 send_seq=5506 receive_seq=5506 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997499 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=15163 bytes_read=595941 bytes_retransmit=9 bytes_invalid=0 send_seq=2473 receive_seq=2473 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15703 bytes_read=47147 bytes_retransmit=9 bytes_invalid=0 send_seq=2464 receive_seq=2464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64275 bytes_read=1053647 bytes_retransmit=0 bytes_invalid=0 send_seq=6561 receive_seq=6561 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998646 coil_temp=17.6 refs=0 mcu_temp=20.73 supply_voltage=3.012 th0: temp=46.1 th1: temp=46.0 th2: temp=49.9 th3: temp=48.0 sysload=0.14 cputime=209.612 memavail=7398080 print_time=2372.045 buffer_time=2.084 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 34 Hz
Testing frequency 35 Hz
Stats 2348.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=18642064 bytes_read=2291195 bytes_retransmit=9 bytes_invalid=0 send_seq=324843 receive_seq=324843 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=7872 freq=400015920 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=14956 bytes_read=48077 bytes_retransmit=0 bytes_invalid=0 send_seq=2464 receive_seq=2464 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997276 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101493 bytes_read=3172411 bytes_retransmit=9 bytes_invalid=0 send_seq=13662 receive_seq=13662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997644 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43857 bytes_read=728980 bytes_retransmit=9 bytes_invalid=0 send_seq=5517 receive_seq=5517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997487 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=15169 bytes_read=596175 bytes_retransmit=9 bytes_invalid=0 send_seq=2474 receive_seq=2474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15709 bytes_read=47163 bytes_retransmit=9 bytes_invalid=0 send_seq=2465 receive_seq=2465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64281 bytes_read=1054003 bytes_retransmit=0 bytes_invalid=0 send_seq=6562 receive_seq=6562 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998649 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=46.2 th1: temp=45.8 th2: temp=49.9 th3: temp=48.0 sysload=0.14 cputime=209.737 memavail=7398080 print_time=2373.253 buffer_time=2.291 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 36 Hz
Stats 2349.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=18650157 bytes_read=2292230 bytes_retransmit=9 bytes_invalid=0 send_seq=324988 receive_seq=324988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=6387 freq=400015900 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14962 bytes_read=48106 bytes_retransmit=0 bytes_invalid=0 send_seq=2465 receive_seq=2465 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997266 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101569 bytes_read=3175481 bytes_retransmit=9 bytes_invalid=0 send_seq=13673 receive_seq=13673 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997652 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=43933 bytes_read=732053 bytes_retransmit=9 bytes_invalid=0 send_seq=5528 receive_seq=5528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=15175 bytes_read=596439 bytes_retransmit=9 bytes_invalid=0 send_seq=2475 receive_seq=2475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15715 bytes_read=47179 bytes_retransmit=9 bytes_invalid=0 send_seq=2466 receive_seq=2466 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64287 bytes_read=1054359 bytes_retransmit=0 bytes_invalid=0 send_seq=6563 receive_seq=6563 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998664 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=46.4 th1: temp=46.1 th2: temp=49.8 th3: temp=48.1 sysload=0.14 cputime=209.855 memavail=7397860 print_time=2374.131 buffer_time=2.169 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2350.5: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18657234 bytes_read=2293236 bytes_retransmit=9 bytes_invalid=0 send_seq=325119 receive_seq=325119 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=7819 freq=400015883 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14968 bytes_read=48122 bytes_retransmit=0 bytes_invalid=0 send_seq=2466 receive_seq=2466 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997323 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101645 bytes_read=3178551 bytes_retransmit=9 bytes_invalid=0 send_seq=13684 receive_seq=13684 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997684 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44009 bytes_read=735124 bytes_retransmit=9 bytes_invalid=0 send_seq=5539 receive_seq=5539 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15181 bytes_read=596718 bytes_retransmit=9 bytes_invalid=0 send_seq=2476 receive_seq=2476 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15721 bytes_read=47195 bytes_retransmit=9 bytes_invalid=0 send_seq=2467 receive_seq=2467 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64293 bytes_read=1054715 bytes_retransmit=0 bytes_invalid=0 send_seq=6564 receive_seq=6564 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998679 coil_temp=17.6 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=46.6 th1: temp=45.9 th2: temp=49.8 th3: temp=47.9 sysload=0.14 cputime=209.972 memavail=7397860 print_time=2375.083 buffer_time=2.120 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 37 Hz
Testing frequency 38 Hz
Stats 2351.5: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18666037 bytes_read=2294325 bytes_retransmit=9 bytes_invalid=0 send_seq=325275 receive_seq=325275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=9032 freq=400015871 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14974 bytes_read=48138 bytes_retransmit=0 bytes_invalid=0 send_seq=2467 receive_seq=2467 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997378 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101721 bytes_read=3181625 bytes_retransmit=9 bytes_invalid=0 send_seq=13695 receive_seq=13695 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997707 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44085 bytes_read=738238 bytes_retransmit=9 bytes_invalid=0 send_seq=5550 receive_seq=5550 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997581 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15187 bytes_read=596952 bytes_retransmit=9 bytes_invalid=0 send_seq=2477 receive_seq=2477 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997682 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15727 bytes_read=47211 bytes_retransmit=9 bytes_invalid=0 send_seq=2468 receive_seq=2468 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999447 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64299 bytes_read=1055071 bytes_retransmit=0 bytes_invalid=0 send_seq=6565 receive_seq=6565 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998684 coil_temp=17.6 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=45.6 th1: temp=46.2 th2: temp=49.9 th3: temp=48.0 sysload=0.14 cputime=210.102 memavail=7397860 print_time=2376.267 buffer_time=2.303 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 39 Hz
Stats 2352.5: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18674633 bytes_read=2295405 bytes_retransmit=9 bytes_invalid=0 send_seq=325429 receive_seq=325429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=7280 freq=400015865 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14980 bytes_read=48154 bytes_retransmit=0 bytes_invalid=0 send_seq=2468 receive_seq=2468 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997386 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101797 bytes_read=3184753 bytes_retransmit=9 bytes_invalid=0 send_seq=13706 receive_seq=13706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997707 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44161 bytes_read=741312 bytes_retransmit=9 bytes_invalid=0 send_seq=5561 receive_seq=5561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997678 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15193 bytes_read=597216 bytes_retransmit=9 bytes_invalid=0 send_seq=2478 receive_seq=2478 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15733 bytes_read=47238 bytes_retransmit=9 bytes_invalid=0 send_seq=2469 receive_seq=2469 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64305 bytes_read=1055427 bytes_retransmit=0 bytes_invalid=0 send_seq=6566 receive_seq=6566 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998682 coil_temp=17.6 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=46.5 th1: temp=46.0 th2: temp=49.9 th3: temp=48.0 sysload=0.13 cputime=210.223 memavail=7397860 print_time=2377.154 buffer_time=2.189 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 40 Hz
Stats 2353.5: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18682242 bytes_read=2296429 bytes_retransmit=9 bytes_invalid=0 send_seq=325566 receive_seq=325566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=8500 freq=400015902 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14986 bytes_read=48170 bytes_retransmit=0 bytes_invalid=0 send_seq=2469 receive_seq=2469 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997388 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101873 bytes_read=3187826 bytes_retransmit=9 bytes_invalid=0 send_seq=13717 receive_seq=13717 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997713 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44237 bytes_read=744401 bytes_retransmit=9 bytes_invalid=0 send_seq=5572 receive_seq=5572 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997654 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15199 bytes_read=597480 bytes_retransmit=9 bytes_invalid=0 send_seq=2479 receive_seq=2479 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997682 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15739 bytes_read=47254 bytes_retransmit=9 bytes_invalid=0 send_seq=2470 receive_seq=2470 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999453 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64311 bytes_read=1055783 bytes_retransmit=0 bytes_invalid=0 send_seq=6567 receive_seq=6567 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998722 coil_temp=17.6 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=46.4 th1: temp=45.8 th2: temp=49.8 th3: temp=47.8 sysload=0.13 cputime=210.343 memavail=7397860 print_time=2378.108 buffer_time=2.144 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2354.5: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18691324 bytes_read=2297554 bytes_retransmit=9 bytes_invalid=0 send_seq=325729 receive_seq=325729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=6616 freq=400015887 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14992 bytes_read=48199 bytes_retransmit=0 bytes_invalid=0 send_seq=2470 receive_seq=2470 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997303 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101949 bytes_read=3190884 bytes_retransmit=9 bytes_invalid=0 send_seq=13728 receive_seq=13728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997629 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44313 bytes_read=747458 bytes_retransmit=9 bytes_invalid=0 send_seq=5583 receive_seq=5583 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997541 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15205 bytes_read=597714 bytes_retransmit=9 bytes_invalid=0 send_seq=2480 receive_seq=2480 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15745 bytes_read=47270 bytes_retransmit=9 bytes_invalid=0 send_seq=2471 receive_seq=2471 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64317 bytes_read=1056139 bytes_retransmit=0 bytes_invalid=0 send_seq=6568 receive_seq=6568 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998672 coil_temp=17.6 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.4 th1: temp=46.2 th2: temp=50.1 th3: temp=47.9 sysload=0.13 cputime=210.469 memavail=7397876 print_time=2378.986 buffer_time=2.021 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 41 Hz
Testing frequency 42 Hz
Stats 2355.5: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18700161 bytes_read=2298675 bytes_retransmit=9 bytes_invalid=0 send_seq=325888 receive_seq=325888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=8522 freq=400015879 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=14998 bytes_read=48215 bytes_retransmit=0 bytes_invalid=0 send_seq=2471 receive_seq=2471 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997314 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102025 bytes_read=3193954 bytes_retransmit=9 bytes_invalid=0 send_seq=13739 receive_seq=13739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997679 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44389 bytes_read=750528 bytes_retransmit=9 bytes_invalid=0 send_seq=5594 receive_seq=5594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997542 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15211 bytes_read=597993 bytes_retransmit=9 bytes_invalid=0 send_seq=2481 receive_seq=2481 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15751 bytes_read=47286 bytes_retransmit=9 bytes_invalid=0 send_seq=2472 receive_seq=2472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64323 bytes_read=1056495 bytes_retransmit=0 bytes_invalid=0 send_seq=6569 receive_seq=6569 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998686 coil_temp=17.6 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.2 th1: temp=46.1 th2: temp=49.8 th3: temp=47.7 sysload=0.13 cputime=210.611 memavail=7391828 print_time=2380.197 buffer_time=2.231 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 43 Hz
Stats 2356.5: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18708187 bytes_read=2299734 bytes_retransmit=9 bytes_invalid=0 send_seq=326032 receive_seq=326032 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=9871 freq=400015875 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15004 bytes_read=48231 bytes_retransmit=0 bytes_invalid=0 send_seq=2472 receive_seq=2472 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997300 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102101 bytes_read=3197043 bytes_retransmit=9 bytes_invalid=0 send_seq=13750 receive_seq=13750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997683 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44465 bytes_read=753600 bytes_retransmit=9 bytes_invalid=0 send_seq=5605 receive_seq=5605 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15217 bytes_read=598257 bytes_retransmit=9 bytes_invalid=0 send_seq=2482 receive_seq=2482 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997677 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15757 bytes_read=47302 bytes_retransmit=9 bytes_invalid=0 send_seq=2473 receive_seq=2473 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64329 bytes_read=1056851 bytes_retransmit=0 bytes_invalid=0 send_seq=6570 receive_seq=6570 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998674 coil_temp=17.6 refs=0 mcu_temp=20.68 supply_voltage=3.012 th0: temp=46.5 th1: temp=46.1 th2: temp=49.7 th3: temp=48.0 sysload=0.13 cputime=210.735 memavail=7395976 print_time=2381.113 buffer_time=2.147 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2357.5: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18717894 bytes_read=2300904 bytes_retransmit=9 bytes_invalid=0 send_seq=326204 receive_seq=326204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=7576 freq=400015868 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15010 bytes_read=48247 bytes_retransmit=0 bytes_invalid=0 send_seq=2473 receive_seq=2473 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997298 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102177 bytes_read=3200099 bytes_retransmit=9 bytes_invalid=0 send_seq=13761 receive_seq=13761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997714 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44541 bytes_read=756658 bytes_retransmit=9 bytes_invalid=0 send_seq=5616 receive_seq=5616 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15223 bytes_read=598491 bytes_retransmit=9 bytes_invalid=0 send_seq=2483 receive_seq=2483 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15763 bytes_read=47329 bytes_retransmit=9 bytes_invalid=0 send_seq=2474 receive_seq=2474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64335 bytes_read=1057207 bytes_retransmit=0 bytes_invalid=0 send_seq=6571 receive_seq=6571 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998666 coil_temp=17.6 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.5 th1: temp=46.1 th2: temp=49.8 th3: temp=48.0 sysload=0.20 cputime=210.859 memavail=7395976 print_time=2382.016 buffer_time=2.050 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 44 Hz
Testing frequency 45 Hz
Stats 2358.5: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18727549 bytes_read=2302079 bytes_retransmit=9 bytes_invalid=0 send_seq=326377 receive_seq=326377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=8864 freq=400015868 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15016 bytes_read=48263 bytes_retransmit=0 bytes_invalid=0 send_seq=2474 receive_seq=2474 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997284 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102253 bytes_read=3203169 bytes_retransmit=9 bytes_invalid=0 send_seq=13772 receive_seq=13772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997722 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44617 bytes_read=759803 bytes_retransmit=9 bytes_invalid=0 send_seq=5627 receive_seq=5627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15229 bytes_read=598755 bytes_retransmit=9 bytes_invalid=0 send_seq=2484 receive_seq=2484 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997704 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15769 bytes_read=47345 bytes_retransmit=9 bytes_invalid=0 send_seq=2475 receive_seq=2475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64341 bytes_read=1057563 bytes_retransmit=0 bytes_invalid=0 send_seq=6572 receive_seq=6572 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998662 coil_temp=17.6 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.4 th1: temp=46.0 th2: temp=49.8 th3: temp=48.1 sysload=0.20 cputime=210.992 memavail=7395976 print_time=2383.212 buffer_time=2.246 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 46 Hz
Stats 2359.5: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18735574 bytes_read=2303143 bytes_retransmit=9 bytes_invalid=0 send_seq=326522 receive_seq=326522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=10420 freq=400015859 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15022 bytes_read=48292 bytes_retransmit=0 bytes_invalid=0 send_seq=2475 receive_seq=2475 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997269 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102329 bytes_read=3206240 bytes_retransmit=9 bytes_invalid=0 send_seq=13783 receive_seq=13783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997698 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44693 bytes_read=762874 bytes_retransmit=9 bytes_invalid=0 send_seq=5638 receive_seq=5638 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997489 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15235 bytes_read=599019 bytes_retransmit=9 bytes_invalid=0 send_seq=2485 receive_seq=2485 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15775 bytes_read=47361 bytes_retransmit=9 bytes_invalid=0 send_seq=2476 receive_seq=2476 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64347 bytes_read=1057919 bytes_retransmit=0 bytes_invalid=0 send_seq=6573 receive_seq=6573 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998646 coil_temp=17.6 refs=0 mcu_temp=20.68 supply_voltage=3.012 th0: temp=46.5 th1: temp=46.1 th2: temp=49.9 th3: temp=47.9 sysload=0.20 cputime=211.114 memavail=7395976 print_time=2384.134 buffer_time=2.167 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2360.5: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18745591 bytes_read=2304354 bytes_retransmit=9 bytes_invalid=0 send_seq=326699 receive_seq=326699 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=7911 freq=400015850 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15028 bytes_read=48308 bytes_retransmit=0 bytes_invalid=0 send_seq=2476 receive_seq=2476 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997281 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102398 bytes_read=3209333 bytes_retransmit=9 bytes_invalid=0 send_seq=13793 receive_seq=13793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997705 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44762 bytes_read=765908 bytes_retransmit=9 bytes_invalid=0 send_seq=5648 receive_seq=5648 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997494 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=15241 bytes_read=599268 bytes_retransmit=9 bytes_invalid=0 send_seq=2486 receive_seq=2486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15781 bytes_read=47377 bytes_retransmit=9 bytes_invalid=0 send_seq=2477 receive_seq=2477 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999461 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64353 bytes_read=1058275 bytes_retransmit=0 bytes_invalid=0 send_seq=6574 receive_seq=6574 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998658 coil_temp=17.6 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.6 th1: temp=46.3 th2: temp=50.1 th3: temp=48.0 sysload=0.20 cputime=211.238 memavail=7395992 print_time=2385.021 buffer_time=2.054 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 47 Hz
Testing frequency 48 Hz
Stats 2361.5: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18755519 bytes_read=2305540 bytes_retransmit=9 bytes_invalid=0 send_seq=326876 receive_seq=326875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=9385 freq=400015834 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15034 bytes_read=48324 bytes_retransmit=0 bytes_invalid=0 send_seq=2477 receive_seq=2477 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997287 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102474 bytes_read=3212435 bytes_retransmit=9 bytes_invalid=0 send_seq=13804 receive_seq=13804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997804 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44838 bytes_read=768982 bytes_retransmit=9 bytes_invalid=0 send_seq=5659 receive_seq=5659 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=15247 bytes_read=599547 bytes_retransmit=9 bytes_invalid=0 send_seq=2487 receive_seq=2487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15787 bytes_read=47393 bytes_retransmit=9 bytes_invalid=0 send_seq=2478 receive_seq=2478 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999461 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64359 bytes_read=1058631 bytes_retransmit=0 bytes_invalid=0 send_seq=6575 receive_seq=6575 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998664 coil_temp=17.6 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.6 th1: temp=46.2 th2: temp=49.9 th3: temp=47.9 sysload=0.20 cputime=211.376 memavail=7395992 print_time=2386.231 buffer_time=2.258 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 49 Hz
Stats 2362.5: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18763727 bytes_read=2306634 bytes_retransmit=9 bytes_invalid=0 send_seq=327026 receive_seq=327026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=11204 freq=400015845 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15040 bytes_read=48340 bytes_retransmit=0 bytes_invalid=0 send_seq=2478 receive_seq=2478 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997301 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102550 bytes_read=3215495 bytes_retransmit=9 bytes_invalid=0 send_seq=13815 receive_seq=13815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997806 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44914 bytes_read=772052 bytes_retransmit=9 bytes_invalid=0 send_seq=5670 receive_seq=5670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=15253 bytes_read=599796 bytes_retransmit=9 bytes_invalid=0 send_seq=2488 receive_seq=2488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15793 bytes_read=47420 bytes_retransmit=9 bytes_invalid=0 send_seq=2479 receive_seq=2479 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999459 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64365 bytes_read=1058987 bytes_retransmit=0 bytes_invalid=0 send_seq=6576 receive_seq=6576 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998716 coil_temp=17.6 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.5 th1: temp=46.3 th2: temp=49.8 th3: temp=47.9 sysload=0.18 cputime=211.504 memavail=7395992 print_time=2387.151 buffer_time=2.178 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 2363.5: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18773973 bytes_read=2307854 bytes_retransmit=9 bytes_invalid=0 send_seq=327208 receive_seq=327208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=8809 freq=400015833 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15046 bytes_read=48356 bytes_retransmit=0 bytes_invalid=0 send_seq=2479 receive_seq=2479 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997282 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102626 bytes_read=3218553 bytes_retransmit=9 bytes_invalid=0 send_seq=13826 receive_seq=13826 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997770 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=44990 bytes_read=775126 bytes_retransmit=9 bytes_invalid=0 send_seq=5681 receive_seq=5681 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997536 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=15259 bytes_read=600030 bytes_retransmit=9 bytes_invalid=0 send_seq=2489 receive_seq=2489 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15799 bytes_read=47436 bytes_retransmit=9 bytes_invalid=0 send_seq=2480 receive_seq=2480 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64371 bytes_read=1059343 bytes_retransmit=0 bytes_invalid=0 send_seq=6577 receive_seq=6577 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998687 coil_temp=17.6 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.1 th2: temp=49.8 th3: temp=48.0 sysload=0.18 cputime=211.632 memavail=7395992 print_time=2388.050 buffer_time=2.076 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 50 Hz
Testing frequency 51 Hz
Stats 2364.5: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18784331 bytes_read=2309054 bytes_retransmit=9 bytes_invalid=0 send_seq=327386 receive_seq=327386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=10008 freq=400015826 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15052 bytes_read=48385 bytes_retransmit=0 bytes_invalid=0 send_seq=2480 receive_seq=2480 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997292 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102702 bytes_read=3221696 bytes_retransmit=9 bytes_invalid=0 send_seq=13837 receive_seq=13837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997846 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45066 bytes_read=778271 bytes_retransmit=9 bytes_invalid=0 send_seq=5692 receive_seq=5692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997540 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=15265 bytes_read=600324 bytes_retransmit=9 bytes_invalid=0 send_seq=2490 receive_seq=2490 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997692 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15805 bytes_read=47452 bytes_retransmit=9 bytes_invalid=0 send_seq=2481 receive_seq=2481 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64377 bytes_read=1059699 bytes_retransmit=0 bytes_invalid=0 send_seq=6578 receive_seq=6578 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998681 coil_temp=17.6 refs=0 mcu_temp=20.70 supply_voltage=3.012 th0: temp=46.5 th1: temp=46.0 th2: temp=50.0 th3: temp=48.0 sysload=0.18 cputime=211.772 memavail=7395992 print_time=2389.242 buffer_time=2.261 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 52 Hz
Stats 2365.5: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18792851 bytes_read=2310164 bytes_retransmit=9 bytes_invalid=0 send_seq=327537 receive_seq=327537 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=11492 freq=400015824 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15058 bytes_read=48401 bytes_retransmit=0 bytes_invalid=0 send_seq=2481 receive_seq=2481 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997290 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102778 bytes_read=3224753 bytes_retransmit=9 bytes_invalid=0 send_seq=13848 receive_seq=13848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997905 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45142 bytes_read=781328 bytes_retransmit=9 bytes_invalid=0 send_seq=5703 receive_seq=5703 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=15271 bytes_read=600573 bytes_retransmit=9 bytes_invalid=0 send_seq=2491 receive_seq=2491 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997692 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15811 bytes_read=47468 bytes_retransmit=9 bytes_invalid=0 send_seq=2482 receive_seq=2482 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999454 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64383 bytes_read=1060055 bytes_retransmit=0 bytes_invalid=0 send_seq=6579 receive_seq=6579 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998680 coil_temp=17.6 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.6 th1: temp=46.2 th2: temp=50.0 th3: temp=48.0 sysload=0.18 cputime=211.898 memavail=7395516 print_time=2390.158 buffer_time=2.176 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2366.5: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18803411 bytes_read=2311409 bytes_retransmit=9 bytes_invalid=0 send_seq=327724 receive_seq=327724 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=35 upcoming_bytes=9255 freq=400015922 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15064 bytes_read=48417 bytes_retransmit=0 bytes_invalid=0 send_seq=2482 receive_seq=2482 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997286 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102854 bytes_read=3227826 bytes_retransmit=9 bytes_invalid=0 send_seq=13859 receive_seq=13859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997950 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45218 bytes_read=784387 bytes_retransmit=9 bytes_invalid=0 send_seq=5714 receive_seq=5714 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997560 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=15277 bytes_read=600807 bytes_retransmit=9 bytes_invalid=0 send_seq=2492 receive_seq=2492 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15817 bytes_read=47484 bytes_retransmit=9 bytes_invalid=0 send_seq=2483 receive_seq=2483 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64389 bytes_read=1060411 bytes_retransmit=0 bytes_invalid=0 send_seq=6580 receive_seq=6580 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998667 coil_temp=17.6 refs=0 mcu_temp=20.70 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.3 th2: temp=49.9 th3: temp=48.0 sysload=0.18 cputime=212.026 memavail=7395528 print_time=2391.057 buffer_time=2.075 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 53 Hz
Testing frequency 54 Hz
Stats 2367.5: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18813780 bytes_read=2312639 bytes_retransmit=9 bytes_invalid=0 send_seq=327908 receive_seq=327908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=9376 freq=400016006 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15070 bytes_read=48433 bytes_retransmit=0 bytes_invalid=0 send_seq=2483 receive_seq=2483 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997121 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102930 bytes_read=3230910 bytes_retransmit=9 bytes_invalid=0 send_seq=13870 receive_seq=13870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997775 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45294 bytes_read=787471 bytes_retransmit=9 bytes_invalid=0 send_seq=5725 receive_seq=5725 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997346 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=15283 bytes_read=601101 bytes_retransmit=9 bytes_invalid=0 send_seq=2493 receive_seq=2493 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997540 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15823 bytes_read=47511 bytes_retransmit=9 bytes_invalid=0 send_seq=2484 receive_seq=2484 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999422 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64395 bytes_read=1060767 bytes_retransmit=0 bytes_invalid=0 send_seq=6581 receive_seq=6581 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998560 coil_temp=17.6 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.6 th1: temp=46.6 th2: temp=49.9 th3: temp=47.9 sysload=0.17 cputime=212.157 memavail=7395528 print_time=2391.970 buffer_time=1.987 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 55 Hz
Stats 2368.5: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18822814 bytes_read=2313788 bytes_retransmit=9 bytes_invalid=0 send_seq=328070 receive_seq=328070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=12187 freq=400016061 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15076 bytes_read=48449 bytes_retransmit=0 bytes_invalid=0 send_seq=2484 receive_seq=2484 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997014 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103006 bytes_read=3233967 bytes_retransmit=9 bytes_invalid=0 send_seq=13881 receive_seq=13881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997591 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45370 bytes_read=790544 bytes_retransmit=9 bytes_invalid=0 send_seq=5736 receive_seq=5736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997174 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=15289 bytes_read=601335 bytes_retransmit=9 bytes_invalid=0 send_seq=2494 receive_seq=2494 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997424 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15829 bytes_read=47527 bytes_retransmit=9 bytes_invalid=0 send_seq=2485 receive_seq=2485 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999398 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64401 bytes_read=1061123 bytes_retransmit=0 bytes_invalid=0 send_seq=6582 receive_seq=6582 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998470 coil_temp=17.6 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.6 th1: temp=46.1 th2: temp=49.9 th3: temp=48.0 sysload=0.17 cputime=212.293 memavail=7395528 print_time=2393.168 buffer_time=2.184 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2369.5: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18833839 bytes_read=2315073 bytes_retransmit=9 bytes_invalid=0 send_seq=328265 receive_seq=328265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=9830 freq=400016123 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15082 bytes_read=48478 bytes_retransmit=0 bytes_invalid=0 send_seq=2485 receive_seq=2485 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49996993 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103082 bytes_read=3237023 bytes_retransmit=9 bytes_invalid=0 send_seq=13892 receive_seq=13892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997478 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45446 bytes_read=793660 bytes_retransmit=9 bytes_invalid=0 send_seq=5747 receive_seq=5747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997143 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=15295 bytes_read=601569 bytes_retransmit=9 bytes_invalid=0 send_seq=2495 receive_seq=2495 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997413 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15835 bytes_read=47543 bytes_retransmit=9 bytes_invalid=0 send_seq=2486 receive_seq=2486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999388 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64407 bytes_read=1061479 bytes_retransmit=0 bytes_invalid=0 send_seq=6583 receive_seq=6583 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998458 coil_temp=17.6 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.4 th2: temp=49.9 th3: temp=48.0 sysload=0.17 cputime=212.424 memavail=7395528 print_time=2394.086 buffer_time=2.102 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 56 Hz
Testing frequency 57 Hz
Stats 2370.5: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18844395 bytes_read=2316324 bytes_retransmit=9 bytes_invalid=0 send_seq=328450 receive_seq=328450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=52 upcoming_bytes=11652 freq=400016211 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15088 bytes_read=48494 bytes_retransmit=0 bytes_invalid=0 send_seq=2486 receive_seq=2486 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49996922 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103158 bytes_read=3240166 bytes_retransmit=9 bytes_invalid=0 send_seq=13903 receive_seq=13903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997381 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45522 bytes_read=796746 bytes_retransmit=9 bytes_invalid=0 send_seq=5758 receive_seq=5758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997094 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15301 bytes_read=601878 bytes_retransmit=9 bytes_invalid=0 send_seq=2496 receive_seq=2496 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997383 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15841 bytes_read=47559 bytes_retransmit=9 bytes_invalid=0 send_seq=2487 receive_seq=2487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999380 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64413 bytes_read=1061835 bytes_retransmit=0 bytes_invalid=0 send_seq=6584 receive_seq=6584 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998416 coil_temp=17.6 refs=0 mcu_temp=20.70 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.4 th2: temp=50.0 th3: temp=48.2 sysload=0.17 cputime=212.569 memavail=7395676 print_time=2395.292 buffer_time=2.304 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 58 Hz
Stats 2371.5: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18853755 bytes_read=2317493 bytes_retransmit=9 bytes_invalid=0 send_seq=328616 receive_seq=328616 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=12903 freq=400016183 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15094 bytes_read=48510 bytes_retransmit=0 bytes_invalid=0 send_seq=2487 receive_seq=2487 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49996878 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103234 bytes_read=3243242 bytes_retransmit=9 bytes_invalid=0 send_seq=13914 receive_seq=13914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997269 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45598 bytes_read=799802 bytes_retransmit=9 bytes_invalid=0 send_seq=5769 receive_seq=5769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997022 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15307 bytes_read=602112 bytes_retransmit=9 bytes_invalid=0 send_seq=2497 receive_seq=2497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997318 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15847 bytes_read=47575 bytes_retransmit=9 bytes_invalid=0 send_seq=2488 receive_seq=2488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999363 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64419 bytes_read=1062191 bytes_retransmit=0 bytes_invalid=0 send_seq=6585 receive_seq=6585 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998394 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.8 th1: temp=46.4 th2: temp=50.0 th3: temp=48.0 sysload=0.17 cputime=212.697 memavail=7395792 print_time=2396.181 buffer_time=2.193 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 59 Hz
Stats 2372.5: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18864807 bytes_read=2318779 bytes_retransmit=9 bytes_invalid=0 send_seq=328812 receive_seq=328812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=10676 freq=400016147 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15100 bytes_read=48526 bytes_retransmit=0 bytes_invalid=0 send_seq=2488 receive_seq=2488 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49996957 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103310 bytes_read=3246300 bytes_retransmit=9 bytes_invalid=0 send_seq=13925 receive_seq=13925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997340 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45674 bytes_read=802862 bytes_retransmit=9 bytes_invalid=0 send_seq=5780 receive_seq=5780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997112 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15313 bytes_read=602346 bytes_retransmit=9 bytes_invalid=0 send_seq=2498 receive_seq=2498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997388 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15853 bytes_read=47602 bytes_retransmit=9 bytes_invalid=0 send_seq=2489 receive_seq=2489 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999378 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64425 bytes_read=1062547 bytes_retransmit=0 bytes_invalid=0 send_seq=6586 receive_seq=6586 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998444 coil_temp=17.5 refs=0 mcu_temp=20.68 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.6 th2: temp=50.0 th3: temp=47.9 sysload=0.16 cputime=212.829 memavail=7395808 print_time=2397.103 buffer_time=2.114 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 60 Hz
Stats 2373.5: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18876118 bytes_read=2320064 bytes_retransmit=9 bytes_invalid=0 send_seq=329009 receive_seq=329007 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=10157 freq=400016138 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15106 bytes_read=48542 bytes_retransmit=0 bytes_invalid=0 send_seq=2489 receive_seq=2489 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997045 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103386 bytes_read=3249386 bytes_retransmit=9 bytes_invalid=0 send_seq=13936 receive_seq=13936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997430 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45750 bytes_read=805964 bytes_retransmit=9 bytes_invalid=0 send_seq=5791 receive_seq=5791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997220 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15319 bytes_read=602640 bytes_retransmit=9 bytes_invalid=0 send_seq=2499 receive_seq=2499 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997473 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15859 bytes_read=47618 bytes_retransmit=9 bytes_invalid=0 send_seq=2490 receive_seq=2490 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999395 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64431 bytes_read=1062895 bytes_retransmit=0 bytes_invalid=0 send_seq=6587 receive_seq=6587 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998505 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.8 th1: temp=46.5 th2: temp=50.0 th3: temp=47.8 sysload=0.16 cputime=212.975 memavail=7397720 print_time=2397.986 buffer_time=1.997 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 61 Hz
Stats 2374.5: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18885420 bytes_read=2321238 bytes_retransmit=9 bytes_invalid=0 send_seq=329174 receive_seq=329174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=13567 freq=400016145 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15112 bytes_read=48571 bytes_retransmit=0 bytes_invalid=0 send_seq=2490 receive_seq=2490 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997103 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103462 bytes_read=3252442 bytes_retransmit=9 bytes_invalid=0 send_seq=13947 receive_seq=13947 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997471 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45826 bytes_read=809023 bytes_retransmit=9 bytes_invalid=0 send_seq=5802 receive_seq=5802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997256 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15325 bytes_read=602874 bytes_retransmit=9 bytes_invalid=0 send_seq=2500 receive_seq=2500 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997498 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15865 bytes_read=47634 bytes_retransmit=9 bytes_invalid=0 send_seq=2491 receive_seq=2491 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999401 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64437 bytes_read=1063240 bytes_retransmit=0 bytes_invalid=0 send_seq=6588 receive_seq=6588 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998530 coil_temp=17.6 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.9 th1: temp=46.5 th2: temp=49.8 th3: temp=48.0 sysload=0.16 cputime=213.121 memavail=7397720 print_time=2399.201 buffer_time=2.210 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 62 Hz
Stats 2375.5: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18896888 bytes_read=2322574 bytes_retransmit=9 bytes_invalid=0 send_seq=329376 receive_seq=329376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=11168 freq=400016113 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15118 bytes_read=48587 bytes_retransmit=0 bytes_invalid=0 send_seq=2491 receive_seq=2491 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997134 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103538 bytes_read=3255499 bytes_retransmit=9 bytes_invalid=0 send_seq=13958 receive_seq=13958 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997492 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45902 bytes_read=812138 bytes_retransmit=9 bytes_invalid=0 send_seq=5813 receive_seq=5813 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997311 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15331 bytes_read=603123 bytes_retransmit=9 bytes_invalid=0 send_seq=2501 receive_seq=2501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997537 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15871 bytes_read=47650 bytes_retransmit=9 bytes_invalid=0 send_seq=2492 receive_seq=2492 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999406 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64443 bytes_read=1063585 bytes_retransmit=0 bytes_invalid=0 send_seq=6589 receive_seq=6589 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998571 coil_temp=17.6 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.8 th1: temp=46.5 th2: temp=50.0 th3: temp=48.1 sysload=0.16 cputime=213.257 memavail=7400088 print_time=2400.111 buffer_time=2.119 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2376.5: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18908245 bytes_read=2323854 bytes_retransmit=9 bytes_invalid=0 send_seq=329570 receive_seq=329570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=10824 freq=400016080 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15124 bytes_read=48603 bytes_retransmit=0 bytes_invalid=0 send_seq=2492 receive_seq=2492 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997191 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103614 bytes_read=3258600 bytes_retransmit=9 bytes_invalid=0 send_seq=13969 receive_seq=13969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997555 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=45978 bytes_read=815223 bytes_retransmit=9 bytes_invalid=0 send_seq=5824 receive_seq=5824 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997380 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15337 bytes_read=603417 bytes_retransmit=9 bytes_invalid=0 send_seq=2502 receive_seq=2502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997584 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15877 bytes_read=47666 bytes_retransmit=9 bytes_invalid=0 send_seq=2493 receive_seq=2493 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999419 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64449 bytes_read=1063930 bytes_retransmit=0 bytes_invalid=0 send_seq=6590 receive_seq=6590 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998609 coil_temp=17.6 refs=0 mcu_temp=20.68 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.6 th2: temp=50.0 th3: temp=48.0 sysload=0.16 cputime=213.389 memavail=7400184 print_time=2401.003 buffer_time=2.011 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 63 Hz
Testing frequency 64 Hz
Stats 2377.5: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18917849 bytes_read=2325053 bytes_retransmit=9 bytes_invalid=0 send_seq=329742 receive_seq=329742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=14308 freq=400016058 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15130 bytes_read=48619 bytes_retransmit=0 bytes_invalid=0 send_seq=2493 receive_seq=2493 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997237 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103690 bytes_read=3261716 bytes_retransmit=9 bytes_invalid=0 send_seq=13980 receive_seq=13980 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997644 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46054 bytes_read=818279 bytes_retransmit=9 bytes_invalid=0 send_seq=5835 receive_seq=5835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997446 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15343 bytes_read=603651 bytes_retransmit=9 bytes_invalid=0 send_seq=2503 receive_seq=2503 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997729 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15883 bytes_read=47693 bytes_retransmit=9 bytes_invalid=0 send_seq=2494 receive_seq=2494 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999433 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64455 bytes_read=1064275 bytes_retransmit=0 bytes_invalid=0 send_seq=6591 receive_seq=6591 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998647 coil_temp=17.6 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.0 th2: temp=50.1 th3: temp=48.1 sysload=0.14 cputime=213.534 memavail=7399932 print_time=2402.200 buffer_time=2.208 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 65 Hz
Stats 2378.5: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18929657 bytes_read=2326393 bytes_retransmit=9 bytes_invalid=0 send_seq=329948 receive_seq=329948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=12105 freq=400016032 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15136 bytes_read=48635 bytes_retransmit=0 bytes_invalid=0 send_seq=2494 receive_seq=2494 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997269 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103766 bytes_read=3264774 bytes_retransmit=9 bytes_invalid=0 send_seq=13991 receive_seq=13991 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997673 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46130 bytes_read=821352 bytes_retransmit=9 bytes_invalid=0 send_seq=5846 receive_seq=5846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997645 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15349 bytes_read=603885 bytes_retransmit=9 bytes_invalid=0 send_seq=2504 receive_seq=2504 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997764 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15889 bytes_read=47709 bytes_retransmit=9 bytes_invalid=0 send_seq=2495 receive_seq=2495 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64461 bytes_read=1064620 bytes_retransmit=0 bytes_invalid=0 send_seq=6592 receive_seq=6592 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998710 coil_temp=17.6 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.5 th2: temp=49.9 th3: temp=48.3 sysload=0.14 cputime=213.670 memavail=7399932 print_time=2403.129 buffer_time=2.136 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2379.5: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18941531 bytes_read=2327754 bytes_retransmit=9 bytes_invalid=0 send_seq=330156 receive_seq=330156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=11440 freq=400016020 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15148 bytes_read=48680 bytes_retransmit=0 bytes_invalid=0 send_seq=2496 receive_seq=2496 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997303 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103848 bytes_read=3267875 bytes_retransmit=9 bytes_invalid=0 send_seq=14003 receive_seq=14003 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997714 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46212 bytes_read=824453 bytes_retransmit=9 bytes_invalid=0 send_seq=5858 receive_seq=5858 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997675 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15361 bytes_read=604195 bytes_retransmit=9 bytes_invalid=0 send_seq=2506 receive_seq=2506 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997781 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15901 bytes_read=47741 bytes_retransmit=9 bytes_invalid=0 send_seq=2497 receive_seq=2497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64473 bytes_read=1064980 bytes_retransmit=0 bytes_invalid=0 send_seq=6594 receive_seq=6594 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998738 coil_temp=17.6 refs=0 mcu_temp=20.66 supply_voltage=3.012 th0: temp=46.9 th1: temp=46.8 th2: temp=49.9 th3: temp=47.9 sysload=0.14 cputime=213.803 memavail=7399932 print_time=2403.996 buffer_time=2.002 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 66 Hz
Testing frequency 67 Hz
Stats 2380.5: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18951447 bytes_read=2328984 bytes_retransmit=9 bytes_invalid=0 send_seq=330331 receive_seq=330331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=15003 freq=400015990 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15154 bytes_read=48696 bytes_retransmit=0 bytes_invalid=0 send_seq=2497 receive_seq=2497 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997323 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103917 bytes_read=3270908 bytes_retransmit=9 bytes_invalid=0 send_seq=14013 receive_seq=14013 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997700 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46281 bytes_read=827486 bytes_retransmit=9 bytes_invalid=0 send_seq=5868 receive_seq=5868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997636 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15367 bytes_read=604444 bytes_retransmit=9 bytes_invalid=0 send_seq=2507 receive_seq=2507 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997755 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15907 bytes_read=47757 bytes_retransmit=9 bytes_invalid=0 send_seq=2498 receive_seq=2498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64479 bytes_read=1065325 bytes_retransmit=0 bytes_invalid=0 send_seq=6595 receive_seq=6595 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998740 coil_temp=17.6 refs=0 mcu_temp=20.66 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.3 th2: temp=50.1 th3: temp=48.1 sysload=0.14 cputime=213.948 memavail=7399944 print_time=2405.217 buffer_time=2.223 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 68 Hz
Stats 2381.5: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18963729 bytes_read=2330369 bytes_retransmit=9 bytes_invalid=0 send_seq=330546 receive_seq=330546 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=12980 freq=400015973 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15160 bytes_read=48712 bytes_retransmit=0 bytes_invalid=0 send_seq=2498 receive_seq=2498 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997340 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103993 bytes_read=3273983 bytes_retransmit=9 bytes_invalid=0 send_seq=14024 receive_seq=14024 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997724 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46357 bytes_read=830543 bytes_retransmit=9 bytes_invalid=0 send_seq=5879 receive_seq=5879 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997626 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15373 bytes_read=604678 bytes_retransmit=9 bytes_invalid=0 send_seq=2508 receive_seq=2508 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997742 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15913 bytes_read=47773 bytes_retransmit=9 bytes_invalid=0 send_seq=2499 receive_seq=2499 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999454 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64485 bytes_read=1065675 bytes_retransmit=0 bytes_invalid=0 send_seq=6596 receive_seq=6596 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998729 coil_temp=17.6 refs=0 mcu_temp=20.66 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.5 th2: temp=50.1 th3: temp=48.0 sysload=0.14 cputime=214.087 memavail=7399960 print_time=2406.143 buffer_time=2.148 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2382.5: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18975814 bytes_read=2331727 bytes_retransmit=9 bytes_invalid=0 send_seq=330756 receive_seq=330756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=52 upcoming_bytes=11936 freq=400015962 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15166 bytes_read=48728 bytes_retransmit=0 bytes_invalid=0 send_seq=2499 receive_seq=2499 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997353 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104069 bytes_read=3277071 bytes_retransmit=9 bytes_invalid=0 send_seq=14035 receive_seq=14035 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997731 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46433 bytes_read=833685 bytes_retransmit=9 bytes_invalid=0 send_seq=5890 receive_seq=5890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997621 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15379 bytes_read=604972 bytes_retransmit=9 bytes_invalid=0 send_seq=2509 receive_seq=2509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997791 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15919 bytes_read=47800 bytes_retransmit=9 bytes_invalid=0 send_seq=2500 receive_seq=2500 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999456 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64491 bytes_read=1066031 bytes_retransmit=0 bytes_invalid=0 send_seq=6597 receive_seq=6597 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998730 coil_temp=17.6 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=47.3 th1: temp=46.3 th2: temp=50.1 th3: temp=48.1 sysload=0.13 cputime=214.223 memavail=7399964 print_time=2407.022 buffer_time=2.026 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 69 Hz
Testing frequency 70 Hz
Stats 2383.5: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18986107 bytes_read=2332972 bytes_retransmit=9 bytes_invalid=0 send_seq=330938 receive_seq=330938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=15537 freq=400015948 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15172 bytes_read=48744 bytes_retransmit=0 bytes_invalid=0 send_seq=2500 receive_seq=2500 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997349 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104145 bytes_read=3280127 bytes_retransmit=9 bytes_invalid=0 send_seq=14046 receive_seq=14046 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997741 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46509 bytes_read=836760 bytes_retransmit=9 bytes_invalid=0 send_seq=5901 receive_seq=5901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997614 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15385 bytes_read=605206 bytes_retransmit=9 bytes_invalid=0 send_seq=2510 receive_seq=2510 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997780 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15925 bytes_read=47816 bytes_retransmit=9 bytes_invalid=0 send_seq=2501 receive_seq=2501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999457 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64497 bytes_read=1066387 bytes_retransmit=0 bytes_invalid=0 send_seq=6598 receive_seq=6598 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998720 coil_temp=17.6 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=46.9 th1: temp=46.8 th2: temp=50.3 th3: temp=48.2 sysload=0.13 cputime=214.369 memavail=7399964 print_time=2408.223 buffer_time=2.226 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 71 Hz
Stats 2384.5: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=18998436 bytes_read=2334352 bytes_retransmit=9 bytes_invalid=0 send_seq=331152 receive_seq=331152 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=13788 freq=400015932 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15178 bytes_read=48760 bytes_retransmit=0 bytes_invalid=0 send_seq=2501 receive_seq=2501 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997336 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104221 bytes_read=3283241 bytes_retransmit=9 bytes_invalid=0 send_seq=14057 receive_seq=14057 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997727 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46585 bytes_read=839817 bytes_retransmit=9 bytes_invalid=0 send_seq=5912 receive_seq=5912 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997590 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15391 bytes_read=605440 bytes_retransmit=9 bytes_invalid=0 send_seq=2511 receive_seq=2511 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997745 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15931 bytes_read=47832 bytes_retransmit=9 bytes_invalid=0 send_seq=2502 receive_seq=2502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64503 bytes_read=1066743 bytes_retransmit=0 bytes_invalid=0 send_seq=6599 receive_seq=6599 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998707 coil_temp=17.6 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.8 th2: temp=50.1 th3: temp=48.2 sysload=0.13 cputime=214.511 memavail=7399968 print_time=2409.154 buffer_time=2.157 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2385.5: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19010975 bytes_read=2335763 bytes_retransmit=9 bytes_invalid=0 send_seq=331369 receive_seq=331369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=12698 freq=400015924 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15184 bytes_read=48789 bytes_retransmit=0 bytes_invalid=0 send_seq=2502 receive_seq=2502 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997346 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104297 bytes_read=3286325 bytes_retransmit=9 bytes_invalid=0 send_seq=14068 receive_seq=14068 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997740 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46661 bytes_read=842902 bytes_retransmit=9 bytes_invalid=0 send_seq=5923 receive_seq=5923 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997593 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=15397 bytes_read=605749 bytes_retransmit=9 bytes_invalid=0 send_seq=2512 receive_seq=2512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997747 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15937 bytes_read=47848 bytes_retransmit=9 bytes_invalid=0 send_seq=2503 receive_seq=2503 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999472 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64509 bytes_read=1067099 bytes_retransmit=0 bytes_invalid=0 send_seq=6600 receive_seq=6600 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998706 coil_temp=17.6 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.9 th2: temp=50.3 th3: temp=48.3 sysload=0.13 cputime=214.649 memavail=7398500 print_time=2410.038 buffer_time=2.041 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 72 Hz
Testing frequency 73 Hz
Stats 2386.5: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19021476 bytes_read=2337027 bytes_retransmit=9 bytes_invalid=0 send_seq=331554 receive_seq=331554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=16550 freq=400015915 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15190 bytes_read=48805 bytes_retransmit=0 bytes_invalid=0 send_seq=2503 receive_seq=2503 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997342 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104373 bytes_read=3289398 bytes_retransmit=9 bytes_invalid=0 send_seq=14079 receive_seq=14079 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997738 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46737 bytes_read=845958 bytes_retransmit=9 bytes_invalid=0 send_seq=5934 receive_seq=5934 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997599 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=15403 bytes_read=605983 bytes_retransmit=9 bytes_invalid=0 send_seq=2513 receive_seq=2513 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997739 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15943 bytes_read=47875 bytes_retransmit=9 bytes_invalid=0 send_seq=2504 receive_seq=2504 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999477 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64515 bytes_read=1067455 bytes_retransmit=0 bytes_invalid=0 send_seq=6601 receive_seq=6601 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998702 coil_temp=17.6 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=47.2 th1: temp=46.7 th2: temp=50.2 th3: temp=48.2 sysload=0.13 cputime=214.798 memavail=7398500 print_time=2411.241 buffer_time=2.243 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 74 Hz
Stats 2387.5: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19034285 bytes_read=2338457 bytes_retransmit=9 bytes_invalid=0 send_seq=331778 receive_seq=331778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=15152 freq=400016022 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15196 bytes_read=48821 bytes_retransmit=0 bytes_invalid=0 send_seq=2504 receive_seq=2504 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997339 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104449 bytes_read=3292454 bytes_retransmit=9 bytes_invalid=0 send_seq=14090 receive_seq=14090 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997718 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46813 bytes_read=849016 bytes_retransmit=9 bytes_invalid=0 send_seq=5945 receive_seq=5945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997622 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=15409 bytes_read=606217 bytes_retransmit=9 bytes_invalid=0 send_seq=2514 receive_seq=2514 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997705 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15949 bytes_read=47891 bytes_retransmit=9 bytes_invalid=0 send_seq=2505 receive_seq=2505 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999467 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64521 bytes_read=1067811 bytes_retransmit=0 bytes_invalid=0 send_seq=6602 receive_seq=6602 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998689 coil_temp=17.6 refs=0 mcu_temp=20.70 supply_voltage=3.012 th0: temp=47.3 th1: temp=46.6 th2: temp=50.1 th3: temp=47.9 sysload=0.12 cputime=214.938 memavail=7398504 print_time=2412.178 buffer_time=2.179 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2388.5: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19047323 bytes_read=2339902 bytes_retransmit=9 bytes_invalid=0 send_seq=332005 receive_seq=332005 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=13412 freq=400016080 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15202 bytes_read=48837 bytes_retransmit=0 bytes_invalid=0 send_seq=2505 receive_seq=2505 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997165 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104525 bytes_read=3295539 bytes_retransmit=9 bytes_invalid=0 send_seq=14101 receive_seq=14101 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997511 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46889 bytes_read=852117 bytes_retransmit=9 bytes_invalid=0 send_seq=5956 receive_seq=5956 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997400 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=15415 bytes_read=606511 bytes_retransmit=9 bytes_invalid=0 send_seq=2515 receive_seq=2515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997537 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15955 bytes_read=47907 bytes_retransmit=9 bytes_invalid=0 send_seq=2506 receive_seq=2506 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999425 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64527 bytes_read=1068167 bytes_retransmit=0 bytes_invalid=0 send_seq=6603 receive_seq=6603 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998579 coil_temp=17.6 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.8 th2: temp=50.4 th3: temp=48.2 sysload=0.12 cputime=215.079 memavail=7398516 print_time=2413.054 buffer_time=2.055 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 75 Hz
Testing frequency 76 Hz
Stats 2389.5: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19058052 bytes_read=2341186 bytes_retransmit=9 bytes_invalid=0 send_seq=332194 receive_seq=332194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=17046 freq=400016144 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15208 bytes_read=48853 bytes_retransmit=0 bytes_invalid=0 send_seq=2506 receive_seq=2506 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997073 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104594 bytes_read=3298573 bytes_retransmit=9 bytes_invalid=0 send_seq=14111 receive_seq=14111 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997405 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=46958 bytes_read=855209 bytes_retransmit=9 bytes_invalid=0 send_seq=5966 receive_seq=5966 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997280 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=15421 bytes_read=606745 bytes_retransmit=9 bytes_invalid=0 send_seq=2516 receive_seq=2516 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997442 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15961 bytes_read=47923 bytes_retransmit=9 bytes_invalid=0 send_seq=2507 receive_seq=2507 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999402 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64533 bytes_read=1068523 bytes_retransmit=0 bytes_invalid=0 send_seq=6604 receive_seq=6604 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998520 coil_temp=17.5 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.7 th2: temp=50.1 th3: temp=48.1 sysload=0.12 cputime=215.228 memavail=7398516 print_time=2414.248 buffer_time=2.246 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 77 Hz
Stats 2390.5: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19071284 bytes_read=2342662 bytes_retransmit=9 bytes_invalid=0 send_seq=332424 receive_seq=332424 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=15444 freq=400016119 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=15214 bytes_read=48882 bytes_retransmit=0 bytes_invalid=0 send_seq=2507 receive_seq=2507 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997020 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104670 bytes_read=3301688 bytes_retransmit=9 bytes_invalid=0 send_seq=14122 receive_seq=14122 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997354 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47034 bytes_read=858267 bytes_retransmit=9 bytes_invalid=0 send_seq=5977 receive_seq=5977 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997198 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15427 bytes_read=606994 bytes_retransmit=9 bytes_invalid=0 send_seq=2517 receive_seq=2517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997391 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15967 bytes_read=47939 bytes_retransmit=9 bytes_invalid=0 send_seq=2508 receive_seq=2508 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999388 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64539 bytes_read=1068879 bytes_retransmit=0 bytes_invalid=0 send_seq=6605 receive_seq=6605 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998483 coil_temp=17.6 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=47.3 th1: temp=46.6 th2: temp=50.1 th3: temp=48.3 sysload=0.12 cputime=215.386 memavail=7397356 print_time=2415.181 buffer_time=2.179 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2391.5: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19084413 bytes_read=2344102 bytes_retransmit=9 bytes_invalid=0 send_seq=332650 receive_seq=332650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=13668 freq=400016203 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=15220 bytes_read=48898 bytes_retransmit=0 bytes_invalid=0 send_seq=2508 receive_seq=2508 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997089 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104746 bytes_read=3304790 bytes_retransmit=9 bytes_invalid=0 send_seq=14133 receive_seq=14133 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997461 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47110 bytes_read=861354 bytes_retransmit=9 bytes_invalid=0 send_seq=5988 receive_seq=5988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997274 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15433 bytes_read=607285 bytes_retransmit=9 bytes_invalid=0 send_seq=2518 receive_seq=2518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997490 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15973 bytes_read=47966 bytes_retransmit=9 bytes_invalid=0 send_seq=2509 receive_seq=2509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999401 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64545 bytes_read=1069219 bytes_retransmit=0 bytes_invalid=0 send_seq=6606 receive_seq=6606 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998530 coil_temp=17.6 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=47.8 th1: temp=46.6 th2: temp=50.2 th3: temp=48.1 sysload=0.12 cputime=215.528 memavail=7397356 print_time=2416.049 buffer_time=2.046 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 78 Hz
Testing frequency 79 Hz
Stats 2392.5: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19095270 bytes_read=2345391 bytes_retransmit=9 bytes_invalid=0 send_seq=332840 receive_seq=332840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=14896 freq=400016180 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=15226 bytes_read=48914 bytes_retransmit=0 bytes_invalid=0 send_seq=2509 receive_seq=2509 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49996976 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104822 bytes_read=3307838 bytes_retransmit=9 bytes_invalid=0 send_seq=14144 receive_seq=14144 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997380 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47186 bytes_read=864402 bytes_retransmit=9 bytes_invalid=0 send_seq=5999 receive_seq=5999 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997109 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15439 bytes_read=607503 bytes_retransmit=9 bytes_invalid=0 send_seq=2519 receive_seq=2519 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997361 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15979 bytes_read=47982 bytes_retransmit=9 bytes_invalid=0 send_seq=2510 receive_seq=2510 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999371 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64551 bytes_read=1069575 bytes_retransmit=0 bytes_invalid=0 send_seq=6607 receive_seq=6607 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998449 coil_temp=17.6 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=47.2 th1: temp=46.8 th2: temp=50.2 th3: temp=48.3 sysload=0.11 cputime=215.669 memavail=7397364 print_time=2416.999 buffer_time=1.995 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 80 Hz
Stats 2393.5: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19108748 bytes_read=2346851 bytes_retransmit=9 bytes_invalid=0 send_seq=333071 receive_seq=333071 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=16500 freq=400016298 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=15232 bytes_read=48930 bytes_retransmit=0 bytes_invalid=0 send_seq=2510 receive_seq=2510 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997047 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104898 bytes_read=3310878 bytes_retransmit=9 bytes_invalid=0 send_seq=14155 receive_seq=14155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997449 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47262 bytes_read=867460 bytes_retransmit=9 bytes_invalid=0 send_seq=6010 receive_seq=6010 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997242 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15445 bytes_read=607721 bytes_retransmit=9 bytes_invalid=0 send_seq=2520 receive_seq=2520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997435 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15985 bytes_read=47998 bytes_retransmit=9 bytes_invalid=0 send_seq=2511 receive_seq=2511 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999390 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64557 bytes_read=1069931 bytes_retransmit=0 bytes_invalid=0 send_seq=6608 receive_seq=6608 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998498 coil_temp=17.6 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=47.2 th1: temp=46.6 th2: temp=50.3 th3: temp=48.1 sysload=0.11 cputime=215.822 memavail=7397120 print_time=2418.194 buffer_time=2.190 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2394.5: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19122295 bytes_read=2348336 bytes_retransmit=9 bytes_invalid=0 send_seq=333306 receive_seq=333306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=14320 freq=400016251 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=15238 bytes_read=48946 bytes_retransmit=0 bytes_invalid=0 send_seq=2511 receive_seq=2511 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49996917 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104974 bytes_read=3313945 bytes_retransmit=9 bytes_invalid=0 send_seq=14166 receive_seq=14166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997259 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47338 bytes_read=870527 bytes_retransmit=9 bytes_invalid=0 send_seq=6021 receive_seq=6021 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997067 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15451 bytes_read=607995 bytes_retransmit=9 bytes_invalid=0 send_seq=2521 receive_seq=2521 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997309 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15991 bytes_read=48014 bytes_retransmit=9 bytes_invalid=0 send_seq=2512 receive_seq=2512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999360 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64563 bytes_read=1070287 bytes_retransmit=0 bytes_invalid=0 send_seq=6609 receive_seq=6609 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998434 coil_temp=17.6 refs=0 mcu_temp=20.70 supply_voltage=3.012 th0: temp=47.2 th1: temp=46.7 th2: temp=50.1 th3: temp=48.3 sysload=0.11 cputime=215.962 memavail=7397120 print_time=2419.069 buffer_time=2.064 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 81 Hz
Stats 2395.5: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19133393 bytes_read=2349666 bytes_retransmit=9 bytes_invalid=0 send_seq=333501 receive_seq=333501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=15484 freq=400016212 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15244 bytes_read=48975 bytes_retransmit=0 bytes_invalid=0 send_seq=2512 receive_seq=2512 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997019 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105050 bytes_read=3316986 bytes_retransmit=9 bytes_invalid=0 send_seq=14177 receive_seq=14177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997381 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47414 bytes_read=873566 bytes_retransmit=9 bytes_invalid=0 send_seq=6032 receive_seq=6032 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997228 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15457 bytes_read=608228 bytes_retransmit=9 bytes_invalid=0 send_seq=2522 receive_seq=2522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997429 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=15997 bytes_read=48030 bytes_retransmit=9 bytes_invalid=0 send_seq=2513 receive_seq=2513 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999383 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64569 bytes_read=1070643 bytes_retransmit=0 bytes_invalid=0 send_seq=6610 receive_seq=6610 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998498 coil_temp=17.6 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.6 th2: temp=50.1 th3: temp=48.2 sysload=0.11 cputime=216.103 memavail=7396648 print_time=2420.005 buffer_time=2.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 82 Hz
Testing frequency 83 Hz
Stats 2396.5: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19147229 bytes_read=2351166 bytes_retransmit=9 bytes_invalid=0 send_seq=333739 receive_seq=333739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=17196 freq=400016185 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15250 bytes_read=48991 bytes_retransmit=0 bytes_invalid=0 send_seq=2513 receive_seq=2513 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997113 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105126 bytes_read=3320047 bytes_retransmit=9 bytes_invalid=0 send_seq=14188 receive_seq=14188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997482 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47490 bytes_read=876671 bytes_retransmit=9 bytes_invalid=0 send_seq=6043 receive_seq=6043 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997328 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15463 bytes_read=608446 bytes_retransmit=9 bytes_invalid=0 send_seq=2523 receive_seq=2523 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997503 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16003 bytes_read=48057 bytes_retransmit=9 bytes_invalid=0 send_seq=2514 receive_seq=2514 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999406 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64575 bytes_read=1070999 bytes_retransmit=0 bytes_invalid=0 send_seq=6611 receive_seq=6611 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998589 coil_temp=17.6 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.9 th1: temp=46.8 th2: temp=50.3 th3: temp=48.2 sysload=0.11 cputime=216.260 memavail=7396652 print_time=2421.214 buffer_time=2.208 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 84 Hz
Stats 2397.5: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19160747 bytes_read=2352631 bytes_retransmit=9 bytes_invalid=0 send_seq=333970 receive_seq=333970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=14527 freq=400016161 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15256 bytes_read=49007 bytes_retransmit=0 bytes_invalid=0 send_seq=2514 receive_seq=2514 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997187 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105202 bytes_read=3323133 bytes_retransmit=9 bytes_invalid=0 send_seq=14199 receive_seq=14199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997564 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47566 bytes_read=879755 bytes_retransmit=9 bytes_invalid=0 send_seq=6054 receive_seq=6054 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997407 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15469 bytes_read=608728 bytes_retransmit=9 bytes_invalid=0 send_seq=2524 receive_seq=2524 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997560 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16009 bytes_read=48073 bytes_retransmit=9 bytes_invalid=0 send_seq=2515 receive_seq=2515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999431 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64581 bytes_read=1071355 bytes_retransmit=0 bytes_invalid=0 send_seq=6612 receive_seq=6612 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998617 coil_temp=17.6 refs=0 mcu_temp=20.70 supply_voltage=3.012 th0: temp=47.2 th1: temp=47.0 th2: temp=50.3 th3: temp=48.3 sysload=0.18 cputime=216.407 memavail=7396652 print_time=2422.076 buffer_time=2.069 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2398.5: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19172047 bytes_read=2353965 bytes_retransmit=9 bytes_invalid=0 send_seq=334169 receive_seq=334169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=16164 freq=400016128 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15262 bytes_read=49023 bytes_retransmit=0 bytes_invalid=0 send_seq=2515 receive_seq=2515 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997225 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105278 bytes_read=3326247 bytes_retransmit=9 bytes_invalid=0 send_seq=14210 receive_seq=14210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997659 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47642 bytes_read=882830 bytes_retransmit=9 bytes_invalid=0 send_seq=6065 receive_seq=6065 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997447 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15475 bytes_read=608962 bytes_retransmit=9 bytes_invalid=0 send_seq=2525 receive_seq=2525 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997592 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16015 bytes_read=48089 bytes_retransmit=9 bytes_invalid=0 send_seq=2516 receive_seq=2516 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64587 bytes_read=1071711 bytes_retransmit=0 bytes_invalid=0 send_seq=6613 receive_seq=6613 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998637 coil_temp=17.6 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=47.3 th1: temp=47.0 th2: temp=50.3 th3: temp=48.3 sysload=0.18 cputime=216.548 memavail=7396660 print_time=2423.011 buffer_time=2.004 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 85 Hz
Testing frequency 86 Hz
Stats 2399.5: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19185929 bytes_read=2355475 bytes_retransmit=9 bytes_invalid=0 send_seq=334409 receive_seq=334409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=18077 freq=400016090 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15268 bytes_read=49039 bytes_retransmit=0 bytes_invalid=0 send_seq=2516 receive_seq=2516 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997287 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105347 bytes_read=3329283 bytes_retransmit=9 bytes_invalid=0 send_seq=14220 receive_seq=14220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997710 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47711 bytes_read=885864 bytes_retransmit=9 bytes_invalid=0 send_seq=6075 receive_seq=6075 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997512 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15481 bytes_read=609196 bytes_retransmit=9 bytes_invalid=0 send_seq=2526 receive_seq=2526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16021 bytes_read=48105 bytes_retransmit=9 bytes_invalid=0 send_seq=2517 receive_seq=2517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64593 bytes_read=1072067 bytes_retransmit=0 bytes_invalid=0 send_seq=6614 receive_seq=6614 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998661 coil_temp=17.6 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=47.3 th1: temp=46.7 th2: temp=50.4 th3: temp=48.2 sysload=0.18 cputime=216.787 memavail=7396660 print_time=2424.215 buffer_time=2.207 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 87 Hz
Stats 2400.5: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19200178 bytes_read=2357021 bytes_retransmit=9 bytes_invalid=0 send_seq=334653 receive_seq=334653 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=15103 freq=400016070 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15274 bytes_read=49068 bytes_retransmit=0 bytes_invalid=0 send_seq=2517 receive_seq=2517 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997328 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105423 bytes_read=3332369 bytes_retransmit=9 bytes_invalid=0 send_seq=14231 receive_seq=14231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997746 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47787 bytes_read=888950 bytes_retransmit=9 bytes_invalid=0 send_seq=6086 receive_seq=6086 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997556 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15487 bytes_read=609505 bytes_retransmit=9 bytes_invalid=0 send_seq=2527 receive_seq=2527 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16027 bytes_read=48121 bytes_retransmit=9 bytes_invalid=0 send_seq=2518 receive_seq=2518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999456 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64599 bytes_read=1072423 bytes_retransmit=0 bytes_invalid=0 send_seq=6615 receive_seq=6615 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998692 coil_temp=17.6 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=47.2 th1: temp=46.9 th2: temp=50.5 th3: temp=48.3 sysload=0.18 cputime=216.932 memavail=7396664 print_time=2425.079 buffer_time=2.070 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2401.5: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19211752 bytes_read=2358370 bytes_retransmit=9 bytes_invalid=0 send_seq=334855 receive_seq=334855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=16560 freq=400016282 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15280 bytes_read=49084 bytes_retransmit=0 bytes_invalid=0 send_seq=2518 receive_seq=2518 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997345 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105499 bytes_read=3335443 bytes_retransmit=9 bytes_invalid=0 send_seq=14242 receive_seq=14242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997770 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47863 bytes_read=892006 bytes_retransmit=9 bytes_invalid=0 send_seq=6097 receive_seq=6097 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997575 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15493 bytes_read=609739 bytes_retransmit=9 bytes_invalid=0 send_seq=2528 receive_seq=2528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997700 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16033 bytes_read=48148 bytes_retransmit=9 bytes_invalid=0 send_seq=2519 receive_seq=2519 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999460 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64605 bytes_read=1072779 bytes_retransmit=0 bytes_invalid=0 send_seq=6616 receive_seq=6616 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998702 coil_temp=17.6 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=47.5 th1: temp=47.0 th2: temp=50.3 th3: temp=48.6 sysload=0.18 cputime=217.072 memavail=7396664 print_time=2426.019 buffer_time=2.010 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 88 Hz
Testing frequency 89 Hz
Stats 2402.5: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19225887 bytes_read=2359910 bytes_retransmit=9 bytes_invalid=0 send_seq=335101 receive_seq=335101 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=18249 freq=400016248 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15286 bytes_read=49100 bytes_retransmit=0 bytes_invalid=0 send_seq=2519 receive_seq=2519 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49996977 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105575 bytes_read=3338499 bytes_retransmit=9 bytes_invalid=0 send_seq=14253 receive_seq=14253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997292 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=47939 bytes_read=895063 bytes_retransmit=9 bytes_invalid=0 send_seq=6108 receive_seq=6108 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997187 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15499 bytes_read=609973 bytes_retransmit=9 bytes_invalid=0 send_seq=2529 receive_seq=2529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997357 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16039 bytes_read=48164 bytes_retransmit=9 bytes_invalid=0 send_seq=2520 receive_seq=2520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999373 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64611 bytes_read=1073135 bytes_retransmit=0 bytes_invalid=0 send_seq=6617 receive_seq=6617 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998466 coil_temp=17.6 refs=0 mcu_temp=20.68 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.9 th2: temp=50.4 th3: temp=48.4 sysload=0.17 cputime=217.233 memavail=7396664 print_time=2427.217 buffer_time=2.207 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 90 Hz
Stats 2403.5: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19240135 bytes_read=2361455 bytes_retransmit=9 bytes_invalid=0 send_seq=335348 receive_seq=335348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=15460 freq=400016207 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15292 bytes_read=49116 bytes_retransmit=0 bytes_invalid=0 send_seq=2520 receive_seq=2520 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997098 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105651 bytes_read=3341584 bytes_retransmit=9 bytes_invalid=0 send_seq=14264 receive_seq=14264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997445 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48015 bytes_read=898166 bytes_retransmit=9 bytes_invalid=0 send_seq=6119 receive_seq=6119 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997341 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15505 bytes_read=610267 bytes_retransmit=9 bytes_invalid=0 send_seq=2530 receive_seq=2530 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997476 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16045 bytes_read=48180 bytes_retransmit=9 bytes_invalid=0 send_seq=2521 receive_seq=2521 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999428 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64617 bytes_read=1073491 bytes_retransmit=0 bytes_invalid=0 send_seq=6618 receive_seq=6618 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998544 coil_temp=17.6 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.9 th2: temp=50.5 th3: temp=48.3 sysload=0.17 cputime=217.382 memavail=7396664 print_time=2428.096 buffer_time=2.086 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2404.5: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19251664 bytes_read=2362799 bytes_retransmit=9 bytes_invalid=0 send_seq=335550 receive_seq=335550 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=17118 freq=400016174 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15298 bytes_read=49132 bytes_retransmit=0 bytes_invalid=0 send_seq=2521 receive_seq=2521 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997165 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105727 bytes_read=3344641 bytes_retransmit=9 bytes_invalid=0 send_seq=14275 receive_seq=14275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997546 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48091 bytes_read=901281 bytes_retransmit=9 bytes_invalid=0 send_seq=6130 receive_seq=6130 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997422 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15511 bytes_read=610501 bytes_retransmit=9 bytes_invalid=0 send_seq=2531 receive_seq=2531 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997545 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16051 bytes_read=48196 bytes_retransmit=9 bytes_invalid=0 send_seq=2522 receive_seq=2522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64623 bytes_read=1073847 bytes_retransmit=0 bytes_invalid=0 send_seq=6619 receive_seq=6619 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998587 coil_temp=17.6 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=47.3 th1: temp=46.9 th2: temp=50.4 th3: temp=48.4 sysload=0.17 cputime=217.528 memavail=7396672 print_time=2429.025 buffer_time=2.014 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 91 Hz
Testing frequency 92 Hz
Stats 2405.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19266124 bytes_read=2364370 bytes_retransmit=9 bytes_invalid=0 send_seq=335799 receive_seq=335799 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=19146 freq=400016139 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15304 bytes_read=49161 bytes_retransmit=0 bytes_invalid=0 send_seq=2522 receive_seq=2522 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997227 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105803 bytes_read=3347758 bytes_retransmit=9 bytes_invalid=0 send_seq=14286 receive_seq=14286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997609 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48167 bytes_read=904342 bytes_retransmit=9 bytes_invalid=0 send_seq=6141 receive_seq=6141 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997483 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15517 bytes_read=610750 bytes_retransmit=9 bytes_invalid=0 send_seq=2532 receive_seq=2532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997598 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16057 bytes_read=48212 bytes_retransmit=9 bytes_invalid=0 send_seq=2523 receive_seq=2523 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64629 bytes_read=1074203 bytes_retransmit=0 bytes_invalid=0 send_seq=6620 receive_seq=6620 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998635 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=47.4 th1: temp=47.0 th2: temp=50.5 th3: temp=48.4 sysload=0.17 cputime=217.704 memavail=7395944 print_time=2430.234 buffer_time=2.223 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 93 Hz
Stats 2406.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19280569 bytes_read=2365925 bytes_retransmit=9 bytes_invalid=0 send_seq=336048 receive_seq=336048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=16052 freq=400016196 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15310 bytes_read=49177 bytes_retransmit=0 bytes_invalid=0 send_seq=2523 receive_seq=2523 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997278 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105879 bytes_read=3350861 bytes_retransmit=9 bytes_invalid=0 send_seq=14297 receive_seq=14297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997667 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48243 bytes_read=907431 bytes_retransmit=9 bytes_invalid=0 send_seq=6152 receive_seq=6152 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997552 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15523 bytes_read=611044 bytes_retransmit=9 bytes_invalid=0 send_seq=2533 receive_seq=2533 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16063 bytes_read=48239 bytes_retransmit=9 bytes_invalid=0 send_seq=2524 receive_seq=2524 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999457 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64635 bytes_read=1074559 bytes_retransmit=0 bytes_invalid=0 send_seq=6621 receive_seq=6621 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998657 coil_temp=17.6 refs=0 mcu_temp=20.66 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.9 th2: temp=50.3 th3: temp=48.4 sysload=0.17 cputime=217.855 memavail=7395944 print_time=2431.104 buffer_time=2.092 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2407.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19292686 bytes_read=2367324 bytes_retransmit=9 bytes_invalid=0 send_seq=336260 receive_seq=336260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=17721 freq=400016157 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15316 bytes_read=49193 bytes_retransmit=0 bytes_invalid=0 send_seq=2524 receive_seq=2524 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997178 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105955 bytes_read=3353918 bytes_retransmit=9 bytes_invalid=0 send_seq=14308 receive_seq=14308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997535 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48319 bytes_read=910487 bytes_retransmit=9 bytes_invalid=0 send_seq=6163 receive_seq=6163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997412 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15529 bytes_read=611278 bytes_retransmit=9 bytes_invalid=0 send_seq=2534 receive_seq=2534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997552 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16069 bytes_read=48255 bytes_retransmit=9 bytes_invalid=0 send_seq=2525 receive_seq=2525 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999431 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64641 bytes_read=1074915 bytes_retransmit=0 bytes_invalid=0 send_seq=6622 receive_seq=6622 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998597 coil_temp=17.5 refs=0 mcu_temp=20.66 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.8 th2: temp=50.4 th3: temp=48.4 sysload=0.15 cputime=218.015 memavail=7388396 print_time=2432.035 buffer_time=2.022 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 94 Hz
Testing frequency 95 Hz
Stats 2408.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19307178 bytes_read=2368894 bytes_retransmit=9 bytes_invalid=0 send_seq=336512 receive_seq=336512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=19736 freq=400016144 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15322 bytes_read=49209 bytes_retransmit=0 bytes_invalid=0 send_seq=2525 receive_seq=2525 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997254 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106031 bytes_read=3356978 bytes_retransmit=9 bytes_invalid=0 send_seq=14319 receive_seq=14319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997636 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48395 bytes_read=913562 bytes_retransmit=9 bytes_invalid=0 send_seq=6174 receive_seq=6174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997487 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15535 bytes_read=611512 bytes_retransmit=9 bytes_invalid=0 send_seq=2535 receive_seq=2535 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16075 bytes_read=48271 bytes_retransmit=9 bytes_invalid=0 send_seq=2526 receive_seq=2526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999445 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64647 bytes_read=1075271 bytes_retransmit=0 bytes_invalid=0 send_seq=6623 receive_seq=6623 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998638 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=47.6 th1: temp=47.1 th2: temp=50.5 th3: temp=48.4 sysload=0.15 cputime=218.189 memavail=7395536 print_time=2433.240 buffer_time=2.228 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 96 Hz
Stats 2409.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19322064 bytes_read=2370484 bytes_retransmit=9 bytes_invalid=0 send_seq=336768 receive_seq=336768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=16287 freq=400016107 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15328 bytes_read=49225 bytes_retransmit=0 bytes_invalid=0 send_seq=2526 receive_seq=2526 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997264 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106107 bytes_read=3360063 bytes_retransmit=9 bytes_invalid=0 send_seq=14330 receive_seq=14330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997648 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48471 bytes_read=916647 bytes_retransmit=9 bytes_invalid=0 send_seq=6185 receive_seq=6185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997489 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15541 bytes_read=611806 bytes_retransmit=9 bytes_invalid=0 send_seq=2536 receive_seq=2536 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16081 bytes_read=48287 bytes_retransmit=9 bytes_invalid=0 send_seq=2527 receive_seq=2527 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999445 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64653 bytes_read=1075627 bytes_retransmit=0 bytes_invalid=0 send_seq=6624 receive_seq=6624 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998661 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=47.2 th1: temp=46.9 th2: temp=50.4 th3: temp=48.4 sysload=0.15 cputime=218.345 memavail=7395536 print_time=2434.111 buffer_time=2.098 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2410.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19334171 bytes_read=2371884 bytes_retransmit=9 bytes_invalid=0 send_seq=336978 receive_seq=336977 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=17984 freq=400016080 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15334 bytes_read=49254 bytes_retransmit=0 bytes_invalid=0 send_seq=2527 receive_seq=2527 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997314 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106183 bytes_read=3363120 bytes_retransmit=9 bytes_invalid=0 send_seq=14341 receive_seq=14341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997716 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48547 bytes_read=919705 bytes_retransmit=9 bytes_invalid=0 send_seq=6196 receive_seq=6196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15547 bytes_read=612055 bytes_retransmit=9 bytes_invalid=0 send_seq=2537 receive_seq=2537 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16087 bytes_read=48303 bytes_retransmit=9 bytes_invalid=0 send_seq=2528 receive_seq=2528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64659 bytes_read=1075983 bytes_retransmit=0 bytes_invalid=0 send_seq=6625 receive_seq=6625 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998687 coil_temp=17.5 refs=0 mcu_temp=20.66 supply_voltage=3.012 th0: temp=47.4 th1: temp=47.0 th2: temp=50.5 th3: temp=48.5 sysload=0.15 cputime=218.494 memavail=7395536 print_time=2435.039 buffer_time=2.025 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 97 Hz
Testing frequency 98 Hz
Stats 2411.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19348864 bytes_read=2373469 bytes_retransmit=9 bytes_invalid=0 send_seq=337232 receive_seq=337232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=20096 freq=400016054 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15340 bytes_read=49270 bytes_retransmit=0 bytes_invalid=0 send_seq=2528 receive_seq=2528 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997349 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106259 bytes_read=3366194 bytes_retransmit=9 bytes_invalid=0 send_seq=14352 receive_seq=14352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997748 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48623 bytes_read=922820 bytes_retransmit=9 bytes_invalid=0 send_seq=6207 receive_seq=6207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997996 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15553 bytes_read=612289 bytes_retransmit=9 bytes_invalid=0 send_seq=2538 receive_seq=2538 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997717 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16093 bytes_read=48330 bytes_retransmit=9 bytes_invalid=0 send_seq=2529 receive_seq=2529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999461 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64665 bytes_read=1076339 bytes_retransmit=0 bytes_invalid=0 send_seq=6626 receive_seq=6626 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998707 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=47.5 th1: temp=47.0 th2: temp=50.6 th3: temp=48.5 sysload=0.15 cputime=218.662 memavail=7395536 print_time=2436.243 buffer_time=2.228 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 99 Hz
Stats 2412.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19363740 bytes_read=2375044 bytes_retransmit=9 bytes_invalid=0 send_seq=337485 receive_seq=337485 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=16868 freq=400016026 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15346 bytes_read=49286 bytes_retransmit=0 bytes_invalid=0 send_seq=2529 receive_seq=2529 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997359 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106335 bytes_read=3369337 bytes_retransmit=9 bytes_invalid=0 send_seq=14363 receive_seq=14363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997759 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48699 bytes_read=925905 bytes_retransmit=9 bytes_invalid=0 send_seq=6218 receive_seq=6218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997864 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15559 bytes_read=612583 bytes_retransmit=9 bytes_invalid=0 send_seq=2539 receive_seq=2539 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997721 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16099 bytes_read=48346 bytes_retransmit=9 bytes_invalid=0 send_seq=2530 receive_seq=2530 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999464 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64671 bytes_read=1076695 bytes_retransmit=0 bytes_invalid=0 send_seq=6627 receive_seq=6627 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998710 coil_temp=17.5 refs=0 mcu_temp=20.66 supply_voltage=3.012 th0: temp=47.7 th1: temp=46.9 th2: temp=50.4 th3: temp=48.6 sysload=0.14 cputime=218.816 memavail=7395536 print_time=2437.116 buffer_time=2.100 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2413.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19376092 bytes_read=2376448 bytes_retransmit=9 bytes_invalid=0 send_seq=337698 receive_seq=337698 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=18824 freq=400016052 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15352 bytes_read=49301 bytes_retransmit=0 bytes_invalid=0 send_seq=2530 receive_seq=2530 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997389 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106404 bytes_read=3372371 bytes_retransmit=9 bytes_invalid=0 send_seq=14373 receive_seq=14373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997798 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48768 bytes_read=928957 bytes_retransmit=9 bytes_invalid=0 send_seq=6228 receive_seq=6228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000090 adj=63997862 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15565 bytes_read=612817 bytes_retransmit=9 bytes_invalid=0 send_seq=2540 receive_seq=2540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997756 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16105 bytes_read=48362 bytes_retransmit=9 bytes_invalid=0 send_seq=2531 receive_seq=2531 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999469 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64677 bytes_read=1077051 bytes_retransmit=0 bytes_invalid=0 send_seq=6628 receive_seq=6628 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998729 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=47.4 th1: temp=47.0 th2: temp=50.5 th3: temp=48.6 sysload=0.14 cputime=218.963 memavail=7395552 print_time=2438.048 buffer_time=2.031 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 100 Hz
Testing frequency 101 Hz
Stats 2414.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19391262 bytes_read=2378073 bytes_retransmit=9 bytes_invalid=0 send_seq=337961 receive_seq=337961 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=20632 freq=400016035 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15358 bytes_read=49316 bytes_retransmit=0 bytes_invalid=0 send_seq=2531 receive_seq=2531 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997365 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106480 bytes_read=3375428 bytes_retransmit=9 bytes_invalid=0 send_seq=14384 receive_seq=14384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997746 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48844 bytes_read=932014 bytes_retransmit=9 bytes_invalid=0 send_seq=6239 receive_seq=6239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000086 adj=63998056 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15571 bytes_read=613051 bytes_retransmit=9 bytes_invalid=0 send_seq=2541 receive_seq=2541 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997693 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16111 bytes_read=48378 bytes_retransmit=9 bytes_invalid=0 send_seq=2532 receive_seq=2532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999453 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64683 bytes_read=1077407 bytes_retransmit=0 bytes_invalid=0 send_seq=6629 receive_seq=6629 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998691 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=47.6 th1: temp=47.0 th2: temp=50.6 th3: temp=48.6 sysload=0.14 cputime=219.130 memavail=7395552 print_time=2439.251 buffer_time=2.234 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 102 Hz
Stats 2415.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19406491 bytes_read=2379704 bytes_retransmit=9 bytes_invalid=0 send_seq=338223 receive_seq=338223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=17254 freq=400016014 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15364 bytes_read=49344 bytes_retransmit=0 bytes_invalid=0 send_seq=2532 receive_seq=2532 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997343 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106556 bytes_read=3378513 bytes_retransmit=9 bytes_invalid=0 send_seq=14395 receive_seq=14395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997742 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48920 bytes_read=935100 bytes_retransmit=9 bytes_invalid=0 send_seq=6250 receive_seq=6250 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000082 adj=63997877 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15577 bytes_read=613360 bytes_retransmit=9 bytes_invalid=0 send_seq=2542 receive_seq=2542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16117 bytes_read=48394 bytes_retransmit=9 bytes_invalid=0 send_seq=2533 receive_seq=2533 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999454 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64689 bytes_read=1077763 bytes_retransmit=0 bytes_invalid=0 send_seq=6630 receive_seq=6630 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998692 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=47.4 th1: temp=47.2 th2: temp=50.5 th3: temp=48.4 sysload=0.14 cputime=219.287 memavail=7394084 print_time=2440.122 buffer_time=2.105 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2416.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19418845 bytes_read=2381123 bytes_retransmit=9 bytes_invalid=0 send_seq=338439 receive_seq=338439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=19495 freq=400016157 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15370 bytes_read=49359 bytes_retransmit=0 bytes_invalid=0 send_seq=2533 receive_seq=2533 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997354 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106632 bytes_read=3381587 bytes_retransmit=9 bytes_invalid=0 send_seq=14406 receive_seq=14406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997766 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=48996 bytes_read=938157 bytes_retransmit=9 bytes_invalid=0 send_seq=6261 receive_seq=6261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000078 adj=63997831 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15583 bytes_read=613594 bytes_retransmit=9 bytes_invalid=0 send_seq=2543 receive_seq=2543 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997713 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16123 bytes_read=48421 bytes_retransmit=9 bytes_invalid=0 send_seq=2534 receive_seq=2534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999461 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64695 bytes_read=1078119 bytes_retransmit=0 bytes_invalid=0 send_seq=6631 receive_seq=6631 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998706 coil_temp=17.5 refs=0 mcu_temp=20.66 supply_voltage=3.012 th0: temp=47.6 th1: temp=47.2 th2: temp=50.5 th3: temp=48.5 sysload=0.14 cputime=219.434 memavail=7394084 print_time=2441.049 buffer_time=2.031 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 103 Hz
Testing frequency 104 Hz
Stats 2417.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19434361 bytes_read=2382783 bytes_retransmit=9 bytes_invalid=0 send_seq=338709 receive_seq=338709 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=26 upcoming_bytes=21526 freq=400016198 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15376 bytes_read=49374 bytes_retransmit=0 bytes_invalid=0 send_seq=2534 receive_seq=2534 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997089 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106708 bytes_read=3384645 bytes_retransmit=9 bytes_invalid=0 send_seq=14417 receive_seq=14417 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997447 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49072 bytes_read=941215 bytes_retransmit=9 bytes_invalid=0 send_seq=6272 receive_seq=6272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000076 adj=63997440 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15589 bytes_read=613828 bytes_retransmit=9 bytes_invalid=0 send_seq=2544 receive_seq=2544 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997475 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16129 bytes_read=48437 bytes_retransmit=9 bytes_invalid=0 send_seq=2535 receive_seq=2535 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999401 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64701 bytes_read=1078475 bytes_retransmit=0 bytes_invalid=0 send_seq=6632 receive_seq=6632 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998553 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=47.6 th1: temp=47.2 th2: temp=50.6 th3: temp=48.4 sysload=0.13 cputime=219.606 memavail=7394084 print_time=2442.254 buffer_time=2.234 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 105 Hz
Stats 2418.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19449950 bytes_read=2384408 bytes_retransmit=9 bytes_invalid=0 send_seq=338972 receive_seq=338972 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=17934 freq=400016168 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15382 bytes_read=49389 bytes_retransmit=0 bytes_invalid=0 send_seq=2535 receive_seq=2535 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997068 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106784 bytes_read=3387729 bytes_retransmit=9 bytes_invalid=0 send_seq=14428 receive_seq=14428 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997412 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49148 bytes_read=944375 bytes_retransmit=9 bytes_invalid=0 send_seq=6283 receive_seq=6283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000082 adj=63997347 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15595 bytes_read=614122 bytes_retransmit=9 bytes_invalid=0 send_seq=2545 receive_seq=2545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997496 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16135 bytes_read=48453 bytes_retransmit=9 bytes_invalid=0 send_seq=2536 receive_seq=2536 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999410 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64707 bytes_read=1078831 bytes_retransmit=0 bytes_invalid=0 send_seq=6633 receive_seq=6633 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998552 coil_temp=17.6 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=47.5 th1: temp=47.1 th2: temp=50.6 th3: temp=48.6 sysload=0.13 cputime=219.764 memavail=7394084 print_time=2443.128 buffer_time=2.109 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2419.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19462868 bytes_read=2385872 bytes_retransmit=9 bytes_invalid=0 send_seq=339198 receive_seq=339197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=19976 freq=400016131 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15388 bytes_read=49405 bytes_retransmit=0 bytes_invalid=0 send_seq=2536 receive_seq=2536 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997132 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106860 bytes_read=3390843 bytes_retransmit=9 bytes_invalid=0 send_seq=14439 receive_seq=14439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997493 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49224 bytes_read=947433 bytes_retransmit=9 bytes_invalid=0 send_seq=6294 receive_seq=6294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000084 adj=63997497 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15601 bytes_read=614356 bytes_retransmit=9 bytes_invalid=0 send_seq=2546 receive_seq=2546 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997599 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16141 bytes_read=48469 bytes_retransmit=9 bytes_invalid=0 send_seq=2537 receive_seq=2537 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999424 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64713 bytes_read=1079187 bytes_retransmit=0 bytes_invalid=0 send_seq=6634 receive_seq=6634 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998627 coil_temp=17.5 refs=0 mcu_temp=20.66 supply_voltage=3.012 th0: temp=47.6 th1: temp=47.1 th2: temp=50.5 th3: temp=48.5 sysload=0.13 cputime=219.917 memavail=7393832 print_time=2444.060 buffer_time=2.039 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 106 Hz
Testing frequency 107 Hz
Stats 2420.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19478553 bytes_read=2387553 bytes_retransmit=9 bytes_invalid=0 send_seq=339468 receive_seq=339468 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=26 upcoming_bytes=21870 freq=400016099 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15394 bytes_read=49434 bytes_retransmit=0 bytes_invalid=0 send_seq=2537 receive_seq=2537 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997193 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106936 bytes_read=3393901 bytes_retransmit=9 bytes_invalid=0 send_seq=14450 receive_seq=14450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997605 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49300 bytes_read=950491 bytes_retransmit=9 bytes_invalid=0 send_seq=6305 receive_seq=6305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000082 adj=63997604 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15607 bytes_read=614605 bytes_retransmit=9 bytes_invalid=0 send_seq=2547 receive_seq=2547 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16147 bytes_read=48485 bytes_retransmit=9 bytes_invalid=0 send_seq=2538 receive_seq=2538 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64719 bytes_read=1079543 bytes_retransmit=0 bytes_invalid=0 send_seq=6635 receive_seq=6635 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998667 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.2 th2: temp=50.6 th3: temp=48.6 sysload=0.13 cputime=220.094 memavail=7393848 print_time=2445.256 buffer_time=2.235 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 108 Hz
Stats 2421.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19494433 bytes_read=2389228 bytes_retransmit=9 bytes_invalid=0 send_seq=339741 receive_seq=339741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=18216 freq=400016065 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15400 bytes_read=49450 bytes_retransmit=0 bytes_invalid=0 send_seq=2538 receive_seq=2538 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997240 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107012 bytes_read=3397003 bytes_retransmit=9 bytes_invalid=0 send_seq=14461 receive_seq=14461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997722 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49376 bytes_read=953577 bytes_retransmit=9 bytes_invalid=0 send_seq=6316 receive_seq=6316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000079 adj=63997615 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15613 bytes_read=614899 bytes_retransmit=9 bytes_invalid=0 send_seq=2548 receive_seq=2548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16153 bytes_read=48512 bytes_retransmit=9 bytes_invalid=0 send_seq=2539 receive_seq=2539 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999447 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64725 bytes_read=1079899 bytes_retransmit=0 bytes_invalid=0 send_seq=6636 receive_seq=6636 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998678 coil_temp=17.5 refs=0 mcu_temp=20.68 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.5 th2: temp=50.7 th3: temp=48.6 sysload=0.13 cputime=220.255 memavail=7393848 print_time=2446.132 buffer_time=2.109 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2422.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19507306 bytes_read=2390697 bytes_retransmit=9 bytes_invalid=0 send_seq=339967 receive_seq=339967 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=20488 freq=400016034 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15406 bytes_read=49466 bytes_retransmit=0 bytes_invalid=0 send_seq=2539 receive_seq=2539 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997290 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107088 bytes_read=3400061 bytes_retransmit=9 bytes_invalid=0 send_seq=14472 receive_seq=14472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997769 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49452 bytes_read=956635 bytes_retransmit=9 bytes_invalid=0 send_seq=6327 receive_seq=6327 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000076 adj=63997634 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15619 bytes_read=615133 bytes_retransmit=9 bytes_invalid=0 send_seq=2549 receive_seq=2549 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997704 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16159 bytes_read=48528 bytes_retransmit=9 bytes_invalid=0 send_seq=2540 receive_seq=2540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999457 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64731 bytes_read=1080255 bytes_retransmit=0 bytes_invalid=0 send_seq=6637 receive_seq=6637 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998780 coil_temp=17.5 refs=0 mcu_temp=20.68 supply_voltage=3.012 th0: temp=48.1 th1: temp=47.1 th2: temp=50.7 th3: temp=48.5 sysload=0.20 cputime=220.415 memavail=7393872 print_time=2447.063 buffer_time=2.040 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 109 Hz
Testing frequency 110 Hz
Stats 2423.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19523254 bytes_read=2392352 bytes_retransmit=9 bytes_invalid=0 send_seq=340236 receive_seq=340236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=22672 freq=400016042 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15412 bytes_read=49482 bytes_retransmit=0 bytes_invalid=0 send_seq=2540 receive_seq=2540 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997332 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107164 bytes_read=3403118 bytes_retransmit=9 bytes_invalid=0 send_seq=14483 receive_seq=14483 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997802 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49528 bytes_read=959711 bytes_retransmit=9 bytes_invalid=0 send_seq=6338 receive_seq=6338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000074 adj=63997632 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15625 bytes_read=615367 bytes_retransmit=9 bytes_invalid=0 send_seq=2550 receive_seq=2550 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997731 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16165 bytes_read=48544 bytes_retransmit=9 bytes_invalid=0 send_seq=2541 receive_seq=2541 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999464 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64737 bytes_read=1080611 bytes_retransmit=0 bytes_invalid=0 send_seq=6638 receive_seq=6638 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998776 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=47.6 th1: temp=47.2 th2: temp=51.1 th3: temp=48.7 sysload=0.20 cputime=220.590 memavail=7393876 print_time=2448.263 buffer_time=2.239 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 111 Hz
Stats 2424.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19539444 bytes_read=2394037 bytes_retransmit=9 bytes_invalid=0 send_seq=340511 receive_seq=340511 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=18764 freq=400016017 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15418 bytes_read=49498 bytes_retransmit=0 bytes_invalid=0 send_seq=2541 receive_seq=2541 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997295 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107233 bytes_read=3406181 bytes_retransmit=9 bytes_invalid=0 send_seq=14493 receive_seq=14493 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997728 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49604 bytes_read=962796 bytes_retransmit=9 bytes_invalid=0 send_seq=6349 receive_seq=6349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997558 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15631 bytes_read=615661 bytes_retransmit=9 bytes_invalid=0 send_seq=2551 receive_seq=2551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997713 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16171 bytes_read=48560 bytes_retransmit=9 bytes_invalid=0 send_seq=2542 receive_seq=2542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64743 bytes_read=1080967 bytes_retransmit=0 bytes_invalid=0 send_seq=6639 receive_seq=6639 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998759 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.2 th2: temp=50.8 th3: temp=48.8 sysload=0.20 cputime=220.767 memavail=7387576 print_time=2449.138 buffer_time=2.113 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2425.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19552556 bytes_read=2395535 bytes_retransmit=9 bytes_invalid=0 send_seq=340740 receive_seq=340740 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=20936 freq=400016028 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15424 bytes_read=49527 bytes_retransmit=0 bytes_invalid=0 send_seq=2542 receive_seq=2542 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997329 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107309 bytes_read=3409237 bytes_retransmit=9 bytes_invalid=0 send_seq=14504 receive_seq=14504 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997759 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49680 bytes_read=965911 bytes_retransmit=9 bytes_invalid=0 send_seq=6360 receive_seq=6360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997562 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=15637 bytes_read=615910 bytes_retransmit=9 bytes_invalid=0 send_seq=2552 receive_seq=2552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997729 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16177 bytes_read=48576 bytes_retransmit=9 bytes_invalid=0 send_seq=2543 receive_seq=2543 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64749 bytes_read=1081323 bytes_retransmit=0 bytes_invalid=0 send_seq=6640 receive_seq=6640 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998766 coil_temp=17.5 refs=0 mcu_temp=20.68 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.9 th2: temp=51.0 th3: temp=48.8 sysload=0.20 cputime=220.934 memavail=7395540 print_time=2450.064 buffer_time=2.038 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 112 Hz
Testing frequency 113 Hz
Stats 2426.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19568972 bytes_read=2397247 bytes_retransmit=9 bytes_invalid=0 send_seq=341021 receive_seq=341021 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=22691 freq=400016004 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15430 bytes_read=49543 bytes_retransmit=0 bytes_invalid=0 send_seq=2543 receive_seq=2543 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997297 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107385 bytes_read=3412370 bytes_retransmit=9 bytes_invalid=0 send_seq=14515 receive_seq=14515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997710 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49756 bytes_read=968968 bytes_retransmit=9 bytes_invalid=0 send_seq=6371 receive_seq=6371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=15643 bytes_read=616144 bytes_retransmit=9 bytes_invalid=0 send_seq=2553 receive_seq=2553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16183 bytes_read=48603 bytes_retransmit=9 bytes_invalid=0 send_seq=2544 receive_seq=2544 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64755 bytes_read=1081679 bytes_retransmit=0 bytes_invalid=0 send_seq=6641 receive_seq=6641 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998741 coil_temp=17.5 refs=0 mcu_temp=20.68 supply_voltage=3.012 th0: temp=47.8 th1: temp=47.3 th2: temp=50.6 th3: temp=48.7 sysload=0.20 cputime=221.109 memavail=7395288 print_time=2451.272 buffer_time=2.246 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 114 Hz
Stats 2427.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19585245 bytes_read=2398947 bytes_retransmit=9 bytes_invalid=0 send_seq=341299 receive_seq=341299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=18680 freq=400015989 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15436 bytes_read=49559 bytes_retransmit=0 bytes_invalid=0 send_seq=2544 receive_seq=2544 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997313 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107461 bytes_read=3415454 bytes_retransmit=9 bytes_invalid=0 send_seq=14526 receive_seq=14526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997933 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49825 bytes_read=972029 bytes_retransmit=9 bytes_invalid=0 send_seq=6381 receive_seq=6381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=15649 bytes_read=616438 bytes_retransmit=9 bytes_invalid=0 send_seq=2554 receive_seq=2554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16189 bytes_read=48619 bytes_retransmit=9 bytes_invalid=0 send_seq=2545 receive_seq=2545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999463 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64761 bytes_read=1082035 bytes_retransmit=0 bytes_invalid=0 send_seq=6642 receive_seq=6642 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998722 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=47.9 th1: temp=47.3 th2: temp=50.7 th3: temp=48.6 sysload=0.18 cputime=221.271 memavail=7395296 print_time=2452.141 buffer_time=2.114 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2428.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19598413 bytes_read=2400411 bytes_retransmit=9 bytes_invalid=0 send_seq=341524 receive_seq=341524 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=21324 freq=400015988 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15442 bytes_read=49575 bytes_retransmit=0 bytes_invalid=0 send_seq=2545 receive_seq=2545 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997333 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107537 bytes_read=3418510 bytes_retransmit=9 bytes_invalid=0 send_seq=14537 receive_seq=14537 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997924 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49901 bytes_read=975104 bytes_retransmit=9 bytes_invalid=0 send_seq=6392 receive_seq=6392 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997516 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=15655 bytes_read=616672 bytes_retransmit=9 bytes_invalid=0 send_seq=2555 receive_seq=2555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16195 bytes_read=48635 bytes_retransmit=9 bytes_invalid=0 send_seq=2546 receive_seq=2546 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999464 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64767 bytes_read=1082391 bytes_retransmit=0 bytes_invalid=0 send_seq=6643 receive_seq=6643 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998718 coil_temp=17.5 refs=0 mcu_temp=20.68 supply_voltage=3.012 th0: temp=47.6 th1: temp=47.1 th2: temp=50.8 th3: temp=48.8 sysload=0.18 cputime=221.428 memavail=7395044 print_time=2453.073 buffer_time=2.046 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 115 Hz
Testing frequency 116 Hz
Stats 2429.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19614597 bytes_read=2402116 bytes_retransmit=9 bytes_invalid=0 send_seq=341803 receive_seq=341803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=23655 freq=400015968 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15448 bytes_read=49591 bytes_retransmit=0 bytes_invalid=0 send_seq=2546 receive_seq=2546 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997322 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107613 bytes_read=3421567 bytes_retransmit=9 bytes_invalid=0 send_seq=14548 receive_seq=14548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997942 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=49977 bytes_read=978162 bytes_retransmit=9 bytes_invalid=0 send_seq=6403 receive_seq=6403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997502 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=15661 bytes_read=616906 bytes_retransmit=9 bytes_invalid=0 send_seq=2556 receive_seq=2556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16201 bytes_read=48651 bytes_retransmit=9 bytes_invalid=0 send_seq=2547 receive_seq=2547 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999465 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64773 bytes_read=1082747 bytes_retransmit=0 bytes_invalid=0 send_seq=6644 receive_seq=6644 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998705 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=47.9 th1: temp=47.1 th2: temp=50.7 th3: temp=48.6 sysload=0.18 cputime=221.608 memavail=7395052 print_time=2454.275 buffer_time=2.247 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 117 Hz
Stats 2430.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19631366 bytes_read=2403842 bytes_retransmit=9 bytes_invalid=0 send_seq=342083 receive_seq=342083 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=19164 freq=400015950 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15454 bytes_read=49620 bytes_retransmit=0 bytes_invalid=0 send_seq=2547 receive_seq=2547 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997315 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107689 bytes_read=3424652 bytes_retransmit=9 bytes_invalid=0 send_seq=14559 receive_seq=14559 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997883 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50053 bytes_read=981246 bytes_retransmit=9 bytes_invalid=0 send_seq=6414 receive_seq=6414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15667 bytes_read=617215 bytes_retransmit=9 bytes_invalid=0 send_seq=2557 receive_seq=2557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997689 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16207 bytes_read=48667 bytes_retransmit=9 bytes_invalid=0 send_seq=2548 receive_seq=2548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999461 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64779 bytes_read=1083103 bytes_retransmit=0 bytes_invalid=0 send_seq=6645 receive_seq=6645 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998696 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=47.9 th1: temp=47.2 th2: temp=50.6 th3: temp=48.8 sysload=0.18 cputime=221.772 memavail=7395056 print_time=2455.142 buffer_time=2.112 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2431.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19644819 bytes_read=2405351 bytes_retransmit=9 bytes_invalid=0 send_seq=342317 receive_seq=342317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=21516 freq=400015924 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15460 bytes_read=49636 bytes_retransmit=0 bytes_invalid=0 send_seq=2548 receive_seq=2548 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997335 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107765 bytes_read=3427726 bytes_retransmit=9 bytes_invalid=0 send_seq=14570 receive_seq=14570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997874 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50129 bytes_read=984304 bytes_retransmit=9 bytes_invalid=0 send_seq=6425 receive_seq=6425 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997508 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15673 bytes_read=617449 bytes_retransmit=9 bytes_invalid=0 send_seq=2558 receive_seq=2558 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997712 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16213 bytes_read=48694 bytes_retransmit=9 bytes_invalid=0 send_seq=2549 receive_seq=2549 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999464 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64785 bytes_read=1083459 bytes_retransmit=0 bytes_invalid=0 send_seq=6646 receive_seq=6646 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998702 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=48.0 th1: temp=47.2 th2: temp=51.0 th3: temp=48.8 sysload=0.18 cputime=221.929 memavail=7395060 print_time=2456.080 buffer_time=2.050 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 118 Hz
Testing frequency 119 Hz
Stats 2432.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19661333 bytes_read=2407081 bytes_retransmit=9 bytes_invalid=0 send_seq=342601 receive_seq=342601 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=23612 freq=400015897 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15466 bytes_read=49652 bytes_retransmit=0 bytes_invalid=0 send_seq=2549 receive_seq=2549 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997360 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107841 bytes_read=3430783 bytes_retransmit=9 bytes_invalid=0 send_seq=14581 receive_seq=14581 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997881 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50205 bytes_read=987419 bytes_retransmit=9 bytes_invalid=0 send_seq=6436 receive_seq=6436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15679 bytes_read=617683 bytes_retransmit=9 bytes_invalid=0 send_seq=2559 receive_seq=2559 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997733 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16219 bytes_read=48710 bytes_retransmit=9 bytes_invalid=0 send_seq=2550 receive_seq=2550 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999469 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=31.1 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64791 bytes_read=1083815 bytes_retransmit=0 bytes_invalid=0 send_seq=6647 receive_seq=6647 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998717 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=47.9 th1: temp=47.3 th2: temp=50.8 th3: temp=48.7 sysload=0.17 cputime=222.108 memavail=7395060 print_time=2457.279 buffer_time=2.249 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 120 Hz
Stats 2433.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19677999 bytes_read=2408821 bytes_retransmit=9 bytes_invalid=0 send_seq=342887 receive_seq=342887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=19556 freq=400015880 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15472 bytes_read=49668 bytes_retransmit=0 bytes_invalid=0 send_seq=2550 receive_seq=2550 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997369 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107910 bytes_read=3433902 bytes_retransmit=9 bytes_invalid=0 send_seq=14591 receive_seq=14591 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997849 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50281 bytes_read=990520 bytes_retransmit=9 bytes_invalid=0 send_seq=6447 receive_seq=6447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15685 bytes_read=617977 bytes_retransmit=9 bytes_invalid=0 send_seq=2560 receive_seq=2560 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997747 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16225 bytes_read=48726 bytes_retransmit=9 bytes_invalid=0 send_seq=2551 receive_seq=2551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999468 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64797 bytes_read=1084171 bytes_retransmit=0 bytes_invalid=0 send_seq=6648 receive_seq=6648 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998715 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.3 th2: temp=50.7 th3: temp=48.8 sysload=0.17 cputime=222.282 memavail=7394056 print_time=2458.146 buffer_time=2.114 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2434.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19691619 bytes_read=2410325 bytes_retransmit=9 bytes_invalid=0 send_seq=343120 receive_seq=343120 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=21900 freq=400015864 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15478 bytes_read=49684 bytes_retransmit=0 bytes_invalid=0 send_seq=2551 receive_seq=2551 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997383 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107986 bytes_read=3436959 bytes_retransmit=9 bytes_invalid=0 send_seq=14602 receive_seq=14602 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997846 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50357 bytes_read=993576 bytes_retransmit=9 bytes_invalid=0 send_seq=6458 receive_seq=6458 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997550 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15691 bytes_read=618211 bytes_retransmit=9 bytes_invalid=0 send_seq=2561 receive_seq=2561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997752 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16231 bytes_read=48742 bytes_retransmit=9 bytes_invalid=0 send_seq=2552 receive_seq=2552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999471 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64803 bytes_read=1084527 bytes_retransmit=0 bytes_invalid=0 send_seq=6649 receive_seq=6649 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998714 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.3 th2: temp=50.7 th3: temp=49.0 sysload=0.17 cputime=222.446 memavail=7394568 print_time=2459.076 buffer_time=2.041 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 121 Hz
Testing frequency 122 Hz
Stats 2435.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19708270 bytes_read=2412071 bytes_retransmit=9 bytes_invalid=0 send_seq=343404 receive_seq=343404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=24235 freq=400015841 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15484 bytes_read=49713 bytes_retransmit=0 bytes_invalid=0 send_seq=2552 receive_seq=2552 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997407 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108062 bytes_read=3440016 bytes_retransmit=9 bytes_invalid=0 send_seq=14613 receive_seq=14613 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997928 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50433 bytes_read=996636 bytes_retransmit=9 bytes_invalid=0 send_seq=6469 receive_seq=6469 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997559 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15697 bytes_read=618460 bytes_retransmit=9 bytes_invalid=0 send_seq=2562 receive_seq=2562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997755 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16237 bytes_read=48758 bytes_retransmit=9 bytes_invalid=0 send_seq=2553 receive_seq=2553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999479 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64809 bytes_read=1084883 bytes_retransmit=0 bytes_invalid=0 send_seq=6650 receive_seq=6650 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998712 coil_temp=17.5 refs=0 mcu_temp=20.66 supply_voltage=3.012 th0: temp=47.8 th1: temp=47.5 th2: temp=50.9 th3: temp=48.8 sysload=0.17 cputime=222.628 memavail=7393816 print_time=2460.279 buffer_time=2.242 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 123 Hz
Stats 2436.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19725290 bytes_read=2413822 bytes_retransmit=9 bytes_invalid=0 send_seq=343693 receive_seq=343693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=19876 freq=400015839 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15490 bytes_read=49729 bytes_retransmit=0 bytes_invalid=0 send_seq=2553 receive_seq=2553 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997394 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108138 bytes_read=3443119 bytes_retransmit=9 bytes_invalid=0 send_seq=14624 receive_seq=14624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997881 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50509 bytes_read=999720 bytes_retransmit=9 bytes_invalid=0 send_seq=6480 receive_seq=6480 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997577 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15703 bytes_read=618754 bytes_retransmit=9 bytes_invalid=0 send_seq=2563 receive_seq=2563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997752 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16243 bytes_read=48785 bytes_retransmit=9 bytes_invalid=0 send_seq=2554 receive_seq=2554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999474 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64815 bytes_read=1085239 bytes_retransmit=0 bytes_invalid=0 send_seq=6651 receive_seq=6651 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998715 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=47.8 th1: temp=47.3 th2: temp=50.9 th3: temp=48.9 sysload=0.17 cputime=222.788 memavail=7393816 print_time=2461.147 buffer_time=2.110 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2437.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19739201 bytes_read=2415373 bytes_retransmit=9 bytes_invalid=0 send_seq=343937 receive_seq=343936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=22324 freq=400015840 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15496 bytes_read=49745 bytes_retransmit=0 bytes_invalid=0 send_seq=2554 receive_seq=2554 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997373 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108214 bytes_read=3446177 bytes_retransmit=9 bytes_invalid=0 send_seq=14635 receive_seq=14635 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997864 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50585 bytes_read=1002778 bytes_retransmit=9 bytes_invalid=0 send_seq=6491 receive_seq=6491 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15709 bytes_read=618988 bytes_retransmit=9 bytes_invalid=0 send_seq=2564 receive_seq=2564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997743 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16249 bytes_read=48801 bytes_retransmit=9 bytes_invalid=0 send_seq=2555 receive_seq=2555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999469 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64821 bytes_read=1085595 bytes_retransmit=0 bytes_invalid=0 send_seq=6652 receive_seq=6652 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998715 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=47.8 th1: temp=47.5 th2: temp=50.8 th3: temp=48.9 sysload=0.23 cputime=222.953 memavail=7393820 print_time=2462.076 buffer_time=2.038 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 124 Hz
Testing frequency 125 Hz
Stats 2438.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19756075 bytes_read=2417143 bytes_retransmit=9 bytes_invalid=0 send_seq=344228 receive_seq=344228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=24648 freq=400015845 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15502 bytes_read=49761 bytes_retransmit=0 bytes_invalid=0 send_seq=2555 receive_seq=2555 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997357 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108290 bytes_read=3449236 bytes_retransmit=9 bytes_invalid=0 send_seq=14646 receive_seq=14646 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997815 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50661 bytes_read=1005911 bytes_retransmit=9 bytes_invalid=0 send_seq=6502 receive_seq=6502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997534 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15715 bytes_read=619222 bytes_retransmit=9 bytes_invalid=0 send_seq=2565 receive_seq=2565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997746 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16255 bytes_read=48817 bytes_retransmit=9 bytes_invalid=0 send_seq=2556 receive_seq=2556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999466 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64827 bytes_read=1085951 bytes_retransmit=0 bytes_invalid=0 send_seq=6653 receive_seq=6653 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998698 coil_temp=17.5 refs=0 mcu_temp=20.64 supply_voltage=3.012 th0: temp=47.8 th1: temp=47.6 th2: temp=50.6 th3: temp=48.9 sysload=0.23 cputime=223.144 memavail=7393604 print_time=2463.284 buffer_time=2.245 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 126 Hz
Stats 2439.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19773358 bytes_read=2418913 bytes_retransmit=9 bytes_invalid=0 send_seq=344520 receive_seq=344520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=20148 freq=400015826 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15508 bytes_read=49777 bytes_retransmit=0 bytes_invalid=0 send_seq=2556 receive_seq=2556 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997322 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108366 bytes_read=3452378 bytes_retransmit=9 bytes_invalid=0 send_seq=14657 receive_seq=14657 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997755 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50737 bytes_read=1008996 bytes_retransmit=9 bytes_invalid=0 send_seq=6513 receive_seq=6513 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997499 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15721 bytes_read=619516 bytes_retransmit=9 bytes_invalid=0 send_seq=2566 receive_seq=2566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997707 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16261 bytes_read=48833 bytes_retransmit=9 bytes_invalid=0 send_seq=2557 receive_seq=2557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999457 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64833 bytes_read=1086307 bytes_retransmit=0 bytes_invalid=0 send_seq=6654 receive_seq=6654 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998677 coil_temp=17.5 refs=0 mcu_temp=20.64 supply_voltage=3.012 th0: temp=48.0 th1: temp=47.6 th2: temp=50.8 th3: temp=49.0 sysload=0.23 cputime=223.316 memavail=7393352 print_time=2464.154 buffer_time=2.115 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 127 Hz
Stats 2440.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19787434 bytes_read=2420493 bytes_retransmit=9 bytes_invalid=0 send_seq=344765 receive_seq=344765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=22568 freq=400015808 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15514 bytes_read=49806 bytes_retransmit=0 bytes_invalid=0 send_seq=2557 receive_seq=2557 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997346 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108442 bytes_read=3455437 bytes_retransmit=9 bytes_invalid=0 send_seq=14668 receive_seq=14668 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997763 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50806 bytes_read=1012029 bytes_retransmit=9 bytes_invalid=0 send_seq=6523 receive_seq=6523 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997522 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15727 bytes_read=619765 bytes_retransmit=9 bytes_invalid=0 send_seq=2567 receive_seq=2567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997724 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16267 bytes_read=48849 bytes_retransmit=9 bytes_invalid=0 send_seq=2558 receive_seq=2558 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999471 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64839 bytes_read=1086663 bytes_retransmit=0 bytes_invalid=0 send_seq=6655 receive_seq=6655 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998702 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.4 th2: temp=51.0 th3: temp=49.0 sysload=0.23 cputime=223.476 memavail=7393360 print_time=2465.086 buffer_time=2.047 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 128 Hz
Stats 2441.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19804349 bytes_read=2422263 bytes_retransmit=9 bytes_invalid=0 send_seq=345057 receive_seq=345057 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=24832 freq=400015817 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15520 bytes_read=49822 bytes_retransmit=0 bytes_invalid=0 send_seq=2558 receive_seq=2558 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997377 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108518 bytes_read=3458511 bytes_retransmit=9 bytes_invalid=0 send_seq=14679 receive_seq=14679 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997782 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50882 bytes_read=1015086 bytes_retransmit=9 bytes_invalid=0 send_seq=6534 receive_seq=6534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15733 bytes_read=619999 bytes_retransmit=9 bytes_invalid=0 send_seq=2568 receive_seq=2568 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997740 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16273 bytes_read=48876 bytes_retransmit=9 bytes_invalid=0 send_seq=2559 receive_seq=2559 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999477 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64845 bytes_read=1087019 bytes_retransmit=0 bytes_invalid=0 send_seq=6656 receive_seq=6656 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998705 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=47.9 th1: temp=47.4 th2: temp=50.9 th3: temp=48.9 sysload=0.23 cputime=223.659 memavail=7393108 print_time=2466.285 buffer_time=2.245 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 129 Hz
Stats 2442.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19821777 bytes_read=2424059 bytes_retransmit=9 bytes_invalid=0 send_seq=345353 receive_seq=345352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=20408 freq=400015806 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15532 bytes_read=49854 bytes_retransmit=0 bytes_invalid=0 send_seq=2560 receive_seq=2560 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997339 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108600 bytes_read=3461612 bytes_retransmit=9 bytes_invalid=0 send_seq=14691 receive_seq=14691 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997723 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=50964 bytes_read=1018186 bytes_retransmit=9 bytes_invalid=0 send_seq=6546 receive_seq=6546 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15745 bytes_read=620309 bytes_retransmit=9 bytes_invalid=0 send_seq=2570 receive_seq=2570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997701 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16285 bytes_read=48908 bytes_retransmit=9 bytes_invalid=0 send_seq=2561 receive_seq=2561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999461 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64857 bytes_read=1087391 bytes_retransmit=0 bytes_invalid=0 send_seq=6658 receive_seq=6658 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998682 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=47.8 th1: temp=47.3 th2: temp=50.9 th3: temp=48.9 sysload=0.30 cputime=223.841 memavail=7392456 print_time=2467.162 buffer_time=2.121 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 130 Hz
Stats 2443.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19835902 bytes_read=2425633 bytes_retransmit=9 bytes_invalid=0 send_seq=345599 receive_seq=345599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=22716 freq=400015786 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15538 bytes_read=49870 bytes_retransmit=0 bytes_invalid=0 send_seq=2561 receive_seq=2561 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997351 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108669 bytes_read=3464645 bytes_retransmit=9 bytes_invalid=0 send_seq=14701 receive_seq=14701 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997719 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51040 bytes_read=1021260 bytes_retransmit=9 bytes_invalid=0 send_seq=6557 receive_seq=6557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997508 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15751 bytes_read=620543 bytes_retransmit=9 bytes_invalid=0 send_seq=2571 receive_seq=2571 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16291 bytes_read=48924 bytes_retransmit=9 bytes_invalid=0 send_seq=2562 receive_seq=2562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999460 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64863 bytes_read=1087747 bytes_retransmit=0 bytes_invalid=0 send_seq=6659 receive_seq=6659 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998699 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=48.0 th1: temp=47.3 th2: temp=51.1 th3: temp=48.9 sysload=0.30 cputime=224.001 memavail=7392460 print_time=2468.086 buffer_time=2.044 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 131 Hz
Stats 2444.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19852932 bytes_read=2427408 bytes_retransmit=9 bytes_invalid=0 send_seq=345892 receive_seq=345892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=25219 freq=400015781 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15544 bytes_read=49886 bytes_retransmit=0 bytes_invalid=0 send_seq=2562 receive_seq=2562 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997375 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108745 bytes_read=3467703 bytes_retransmit=9 bytes_invalid=0 send_seq=14712 receive_seq=14712 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997741 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51116 bytes_read=1024316 bytes_retransmit=9 bytes_invalid=0 send_seq=6568 receive_seq=6568 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997537 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15757 bytes_read=620777 bytes_retransmit=9 bytes_invalid=0 send_seq=2572 receive_seq=2572 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997728 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16297 bytes_read=48940 bytes_retransmit=9 bytes_invalid=0 send_seq=2563 receive_seq=2563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999464 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64869 bytes_read=1088103 bytes_retransmit=0 bytes_invalid=0 send_seq=6660 receive_seq=6660 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998710 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=48.0 th1: temp=47.5 th2: temp=50.9 th3: temp=49.0 sysload=0.30 cputime=224.184 memavail=7392464 print_time=2469.287 buffer_time=2.244 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 132 Hz
Stats 2445.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19870421 bytes_read=2429239 bytes_retransmit=9 bytes_invalid=0 send_seq=346193 receive_seq=346193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=20996 freq=400015775 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15550 bytes_read=49915 bytes_retransmit=0 bytes_invalid=0 send_seq=2563 receive_seq=2563 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997352 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108821 bytes_read=3470790 bytes_retransmit=9 bytes_invalid=0 send_seq=14723 receive_seq=14723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997722 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51192 bytes_read=1027461 bytes_retransmit=9 bytes_invalid=0 send_seq=6579 receive_seq=6579 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997606 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15763 bytes_read=621086 bytes_retransmit=9 bytes_invalid=0 send_seq=2573 receive_seq=2573 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997706 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16303 bytes_read=48956 bytes_retransmit=9 bytes_invalid=0 send_seq=2564 receive_seq=2564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999458 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=30.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64875 bytes_read=1088459 bytes_retransmit=0 bytes_invalid=0 send_seq=6661 receive_seq=6661 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998700 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=47.9 th1: temp=47.3 th2: temp=50.7 th3: temp=49.0 sysload=0.30 cputime=224.356 memavail=7391748 print_time=2470.162 buffer_time=2.119 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Stats 2446.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19884978 bytes_read=2430848 bytes_retransmit=9 bytes_invalid=0 send_seq=346447 receive_seq=346447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=24572 freq=400015767 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15556 bytes_read=49931 bytes_retransmit=0 bytes_invalid=0 send_seq=2564 receive_seq=2564 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997354 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108897 bytes_read=3473922 bytes_retransmit=9 bytes_invalid=0 send_seq=14734 receive_seq=14734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997721 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51268 bytes_read=1030517 bytes_retransmit=9 bytes_invalid=0 send_seq=6590 receive_seq=6590 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997590 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15769 bytes_read=621320 bytes_retransmit=9 bytes_invalid=0 send_seq=2574 receive_seq=2574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997708 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16309 bytes_read=48983 bytes_retransmit=9 bytes_invalid=0 send_seq=2565 receive_seq=2565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64881 bytes_read=1088815 bytes_retransmit=0 bytes_invalid=0 send_seq=6662 receive_seq=6662 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998698 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=47.9 th1: temp=47.5 th2: temp=50.9 th3: temp=49.0 sysload=0.30 cputime=224.525 memavail=7391760 print_time=2471.139 buffer_time=2.095 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2447.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19902224 bytes_read=2432608 bytes_retransmit=9 bytes_invalid=0 send_seq=346738 receive_seq=346738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=8972 freq=400015749 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15562 bytes_read=49947 bytes_retransmit=0 bytes_invalid=0 send_seq=2565 receive_seq=2565 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997351 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108973 bytes_read=3476980 bytes_retransmit=9 bytes_invalid=0 send_seq=14745 receive_seq=14745 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997821 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51344 bytes_read=1033574 bytes_retransmit=9 bytes_invalid=0 send_seq=6601 receive_seq=6601 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997584 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15775 bytes_read=621554 bytes_retransmit=9 bytes_invalid=0 send_seq=2575 receive_seq=2575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997712 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16315 bytes_read=48999 bytes_retransmit=9 bytes_invalid=0 send_seq=2566 receive_seq=2566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64887 bytes_read=1089171 bytes_retransmit=0 bytes_invalid=0 send_seq=6663 receive_seq=6663 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998691 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=48.1 th1: temp=47.5 th2: temp=51.2 th3: temp=48.9 sysload=0.27 cputime=224.632 memavail=7391760 print_time=2471.139 buffer_time=1.094 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2448.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19912316 bytes_read=2433823 bytes_retransmit=9 bytes_invalid=0 send_seq=346919 receive_seq=346919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015733 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15568 bytes_read=49963 bytes_retransmit=0 bytes_invalid=0 send_seq=2566 receive_seq=2566 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997374 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=109049 bytes_read=3480065 bytes_retransmit=9 bytes_invalid=0 send_seq=14756 receive_seq=14756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997879 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51413 bytes_read=1036653 bytes_retransmit=9 bytes_invalid=0 send_seq=6611 receive_seq=6611 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997601 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15781 bytes_read=621848 bytes_retransmit=9 bytes_invalid=0 send_seq=2576 receive_seq=2576 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997741 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16321 bytes_read=49015 bytes_retransmit=9 bytes_invalid=0 send_seq=2567 receive_seq=2567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999461 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64893 bytes_read=1089527 bytes_retransmit=0 bytes_invalid=0 send_seq=6664 receive_seq=6664 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998701 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=47.9 th1: temp=47.4 th2: temp=51.1 th3: temp=49.0 sysload=0.27 cputime=224.728 memavail=7391760 print_time=2471.139 buffer_time=0.093 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Writing raw accelerometer data to /tmp/raw_data_y_toolboard_t1_t2.csv file
LIS2DW finished 'toolboard_t1' measurements
Writing raw accelerometer data to /tmp/raw_data_y_toolboard_t0_t2.csv file
LIS2DW finished 'toolboard_t0' measurements
Stats 2449.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19912614 bytes_read=2434277 bytes_retransmit=9 bytes_invalid=0 send_seq=346942 receive_seq=346942 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015723 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15574 bytes_read=49979 bytes_retransmit=0 bytes_invalid=0 send_seq=2567 receive_seq=2567 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997383 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=109140 bytes_read=3481851 bytes_retransmit=9 bytes_invalid=0 send_seq=14767 receive_seq=14767 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997890 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51488 bytes_read=1037449 bytes_retransmit=9 bytes_invalid=0 send_seq=6620 receive_seq=6620 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997620 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15787 bytes_read=622082 bytes_retransmit=9 bytes_invalid=0 send_seq=2577 receive_seq=2577 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997763 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16327 bytes_read=49031 bytes_retransmit=9 bytes_invalid=0 send_seq=2568 receive_seq=2568 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999466 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64899 bytes_read=1089883 bytes_retransmit=0 bytes_invalid=0 send_seq=6665 receive_seq=6665 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998718 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=48.0 th1: temp=47.7 th2: temp=51.0 th3: temp=49.2 sysload=0.27 cputime=224.908 memavail=7395028 print_time=2476.821 buffer_time=4.774 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2450.5: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19912912 bytes_read=2434718 bytes_retransmit=9 bytes_invalid=0 send_seq=346965 receive_seq=346965 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015711 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15580 bytes_read=50008 bytes_retransmit=0 bytes_invalid=0 send_seq=2568 receive_seq=2568 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997281 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=109146 bytes_read=3481951 bytes_retransmit=9 bytes_invalid=0 send_seq=14768 receive_seq=14768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997694 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51494 bytes_read=1037549 bytes_retransmit=9 bytes_invalid=0 send_seq=6621 receive_seq=6621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997529 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15793 bytes_read=622331 bytes_retransmit=9 bytes_invalid=0 send_seq=2578 receive_seq=2578 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16333 bytes_read=49047 bytes_retransmit=9 bytes_invalid=0 send_seq=2569 receive_seq=2569 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64905 bytes_read=1090239 bytes_retransmit=0 bytes_invalid=0 send_seq=6666 receive_seq=6666 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998664 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=47.9 th1: temp=47.4 th2: temp=51.2 th3: temp=49.1 sysload=0.27 cputime=224.952 memavail=7395028 print_time=2476.821 buffer_time=3.773 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2451.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19913210 bytes_read=2435157 bytes_retransmit=9 bytes_invalid=0 send_seq=346988 receive_seq=346988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015696 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15586 bytes_read=50024 bytes_retransmit=0 bytes_invalid=0 send_seq=2569 receive_seq=2569 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997296 toolboard_t0: mcu_awake=0.219 mcu_task_avg=0.000115 mcu_task_stddev=0.000070 bytes_write=109152 bytes_read=3482096 bytes_retransmit=9 bytes_invalid=0 send_seq=14769 receive_seq=14769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997704 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51500 bytes_read=1037677 bytes_retransmit=9 bytes_invalid=0 send_seq=6622 receive_seq=6622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997537 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15799 bytes_read=622625 bytes_retransmit=9 bytes_invalid=0 send_seq=2579 receive_seq=2579 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16339 bytes_read=49074 bytes_retransmit=9 bytes_invalid=0 send_seq=2570 receive_seq=2570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64911 bytes_read=1090595 bytes_retransmit=0 bytes_invalid=0 send_seq=6667 receive_seq=6667 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998666 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=48.1 th1: temp=47.4 th2: temp=50.9 th3: temp=49.2 sysload=0.27 cputime=224.996 memavail=7394804 print_time=2476.821 buffer_time=2.773 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Running Command {generate_tension_graphs}...:
Stats 2452.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19913508 bytes_read=2435597 bytes_retransmit=9 bytes_invalid=0 send_seq=347011 receive_seq=347011 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015691 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15592 bytes_read=50040 bytes_retransmit=0 bytes_invalid=0 send_seq=2570 receive_seq=2570 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997308 toolboard_t0: mcu_awake=0.219 mcu_task_avg=0.000115 mcu_task_stddev=0.000070 bytes_write=109158 bytes_read=3482196 bytes_retransmit=9 bytes_invalid=0 send_seq=14770 receive_seq=14770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997711 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=51506 bytes_read=1037777 bytes_retransmit=9 bytes_invalid=0 send_seq=6623 receive_seq=6623 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997549 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15805 bytes_read=622859 bytes_retransmit=9 bytes_invalid=0 send_seq=2580 receive_seq=2580 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16345 bytes_read=49090 bytes_retransmit=9 bytes_invalid=0 send_seq=2571 receive_seq=2571 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64917 bytes_read=1090951 bytes_retransmit=0 bytes_invalid=0 send_seq=6668 receive_seq=6668 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998670 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=47.8 th1: temp=47.8 th2: temp=51.4 th3: temp=49.3 sysload=0.25 cputime=225.058 memavail=7390092 print_time=2476.821 buffer_time=1.772 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=19.2 pwm=0.000
Stats 2453.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19913806 bytes_read=2436022 bytes_retransmit=9 bytes_invalid=0 send_seq=347034 receive_seq=347034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015684 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15598 bytes_read=50056 bytes_retransmit=0 bytes_invalid=0 send_seq=2571 receive_seq=2571 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997316 toolboard_t0: mcu_awake=0.219 mcu_task_avg=0.000115 mcu_task_stddev=0.000070 bytes_write=109164 bytes_read=3482296 bytes_retransmit=9 bytes_invalid=0 send_seq=14771 receive_seq=14771 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997722 toolboard_t1: mcu_awake=0.067 mcu_task_avg=0.000096 mcu_task_stddev=0.000075 bytes_write=51512 bytes_read=1037893 bytes_retransmit=9 bytes_invalid=0 send_seq=6624 receive_seq=6624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997553 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15811 bytes_read=623093 bytes_retransmit=9 bytes_invalid=0 send_seq=2581 receive_seq=2581 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997697 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16351 bytes_read=49106 bytes_retransmit=9 bytes_invalid=0 send_seq=2572 receive_seq=2572 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999453 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64923 bytes_read=1091307 bytes_retransmit=0 bytes_invalid=0 send_seq=6669 receive_seq=6669 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998673 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.9 th2: temp=51.5 th3: temp=49.3 sysload=0.25 cputime=225.113 memavail=7380400 print_time=2476.821 buffer_time=0.771 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2454.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=19914104 bytes_read=2436461 bytes_retransmit=9 bytes_invalid=0 send_seq=347057 receive_seq=347057 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015683 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15604 bytes_read=50072 bytes_retransmit=0 bytes_invalid=0 send_seq=2572 receive_seq=2572 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997323 toolboard_t0: mcu_awake=0.219 mcu_task_avg=0.000115 mcu_task_stddev=0.000070 bytes_write=109170 bytes_read=3482424 bytes_retransmit=9 bytes_invalid=0 send_seq=14772 receive_seq=14772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997723 toolboard_t1: mcu_awake=0.067 mcu_task_avg=0.000096 mcu_task_stddev=0.000075 bytes_write=51518 bytes_read=1038021 bytes_retransmit=9 bytes_invalid=0 send_seq=6625 receive_seq=6625 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997557 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15817 bytes_read=623387 bytes_retransmit=9 bytes_invalid=0 send_seq=2582 receive_seq=2582 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997698 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16357 bytes_read=49122 bytes_retransmit=9 bytes_invalid=0 send_seq=2573 receive_seq=2573 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999454 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64929 bytes_read=1091663 bytes_retransmit=0 bytes_invalid=0 send_seq=6670 receive_seq=6670 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998674 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=47.6 th1: temp=48.1 th2: temp=51.5 th3: temp=49.4 sysload=0.25 cputime=225.168 memavail=7378124 print_time=2476.821 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2455.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=19914402 bytes_read=2436916 bytes_retransmit=9 bytes_invalid=0 send_seq=347080 receive_seq=347080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015681 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=15610 bytes_read=50101 bytes_retransmit=0 bytes_invalid=0 send_seq=2573 receive_seq=2573 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997325 toolboard_t0: mcu_awake=0.219 mcu_task_avg=0.000115 mcu_task_stddev=0.000070 bytes_write=109176 bytes_read=3482524 bytes_retransmit=9 bytes_invalid=0 send_seq=14773 receive_seq=14773 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997730 toolboard_t1: mcu_awake=0.067 mcu_task_avg=0.000096 mcu_task_stddev=0.000075 bytes_write=51524 bytes_read=1038121 bytes_retransmit=9 bytes_invalid=0 send_seq=6626 receive_seq=6626 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=15823 bytes_read=623636 bytes_retransmit=9 bytes_invalid=0 send_seq=2583 receive_seq=2583 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997705 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16363 bytes_read=49138 bytes_retransmit=9 bytes_invalid=0 send_seq=2574 receive_seq=2574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999453 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64935 bytes_read=1092019 bytes_retransmit=0 bytes_invalid=0 send_seq=6671 receive_seq=6671 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998674 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=47.4 th1: temp=48.1 th2: temp=51.6 th3: temp=49.6 sysload=0.25 cputime=225.222 memavail=7376844 print_time=2476.821 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2456.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=19914700 bytes_read=2437341 bytes_retransmit=9 bytes_invalid=0 send_seq=347103 receive_seq=347103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015673 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=15616 bytes_read=50117 bytes_retransmit=0 bytes_invalid=0 send_seq=2574 receive_seq=2574 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997330 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109182 bytes_read=3482638 bytes_retransmit=9 bytes_invalid=0 send_seq=14774 receive_seq=14774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997729 toolboard_t1: mcu_awake=0.067 mcu_task_avg=0.000096 mcu_task_stddev=0.000075 bytes_write=51530 bytes_read=1038221 bytes_retransmit=9 bytes_invalid=0 send_seq=6627 receive_seq=6627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997553 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=15829 bytes_read=623870 bytes_retransmit=9 bytes_invalid=0 send_seq=2584 receive_seq=2584 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997706 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16369 bytes_read=49165 bytes_retransmit=9 bytes_invalid=0 send_seq=2575 receive_seq=2575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999453 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64941 bytes_read=1092375 bytes_retransmit=0 bytes_invalid=0 send_seq=6672 receive_seq=6672 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998674 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=47.1 th1: temp=48.2 th2: temp=51.6 th3: temp=49.7 sysload=0.25 cputime=225.281 memavail=7370364 print_time=2476.821 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Command {generate_tension_graphs} finished

Running Command {generate_tension_graphs}...:
Stats 2457.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=19914998 bytes_read=2437779 bytes_retransmit=9 bytes_invalid=0 send_seq=347126 receive_seq=347126 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015674 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=15622 bytes_read=50133 bytes_retransmit=0 bytes_invalid=0 send_seq=2575 receive_seq=2575 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997346 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109188 bytes_read=3482766 bytes_retransmit=9 bytes_invalid=0 send_seq=14775 receive_seq=14775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997731 toolboard_t1: mcu_awake=0.067 mcu_task_avg=0.000096 mcu_task_stddev=0.000075 bytes_write=51536 bytes_read=1038349 bytes_retransmit=9 bytes_invalid=0 send_seq=6628 receive_seq=6628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997568 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=15835 bytes_read=624164 bytes_retransmit=9 bytes_invalid=0 send_seq=2585 receive_seq=2585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997713 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16375 bytes_read=49181 bytes_retransmit=9 bytes_invalid=0 send_seq=2576 receive_seq=2576 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999454 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64947 bytes_read=1092731 bytes_retransmit=0 bytes_invalid=0 send_seq=6673 receive_seq=6673 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998677 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=48.0 th1: temp=48.2 th2: temp=51.8 th3: temp=49.8 sysload=0.47 cputime=225.367 memavail=7388720 print_time=2476.821 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2458.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=19915296 bytes_read=2438215 bytes_retransmit=9 bytes_invalid=0 send_seq=347149 receive_seq=347149 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015680 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=15628 bytes_read=50149 bytes_retransmit=0 bytes_invalid=0 send_seq=2576 receive_seq=2576 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997371 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109194 bytes_read=3482866 bytes_retransmit=9 bytes_invalid=0 send_seq=14776 receive_seq=14776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997726 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51542 bytes_read=1038463 bytes_retransmit=9 bytes_invalid=0 send_seq=6629 receive_seq=6629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997580 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=15841 bytes_read=624398 bytes_retransmit=9 bytes_invalid=0 send_seq=2586 receive_seq=2586 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997726 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16381 bytes_read=49197 bytes_retransmit=9 bytes_invalid=0 send_seq=2577 receive_seq=2577 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=31.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64953 bytes_read=1093087 bytes_retransmit=0 bytes_invalid=0 send_seq=6674 receive_seq=6674 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998696 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=47.2 th1: temp=48.6 th2: temp=51.7 th3: temp=49.7 sysload=0.47 cputime=225.424 memavail=7377640 print_time=2476.821 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2459.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=19915594 bytes_read=2438640 bytes_retransmit=9 bytes_invalid=0 send_seq=347172 receive_seq=347172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015677 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=15634 bytes_read=50165 bytes_retransmit=0 bytes_invalid=0 send_seq=2577 receive_seq=2577 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997368 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109200 bytes_read=3482961 bytes_retransmit=9 bytes_invalid=0 send_seq=14777 receive_seq=14777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997742 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51548 bytes_read=1038558 bytes_retransmit=9 bytes_invalid=0 send_seq=6630 receive_seq=6630 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997572 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=15847 bytes_read=624632 bytes_retransmit=9 bytes_invalid=0 send_seq=2587 receive_seq=2587 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997715 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16387 bytes_read=49213 bytes_retransmit=9 bytes_invalid=0 send_seq=2578 receive_seq=2578 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=30.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64959 bytes_read=1093443 bytes_retransmit=0 bytes_invalid=0 send_seq=6675 receive_seq=6675 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998695 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=47.2 th1: temp=48.4 th2: temp=52.1 th3: temp=50.1 sysload=0.47 cputime=225.482 memavail=7377252 print_time=2476.821 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2460.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=19915892 bytes_read=2439094 bytes_retransmit=9 bytes_invalid=0 send_seq=347195 receive_seq=347195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015680 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=15640 bytes_read=50194 bytes_retransmit=0 bytes_invalid=0 send_seq=2578 receive_seq=2578 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997373 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109206 bytes_read=3483080 bytes_retransmit=9 bytes_invalid=0 send_seq=14778 receive_seq=14778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997777 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51554 bytes_read=1038677 bytes_retransmit=9 bytes_invalid=0 send_seq=6631 receive_seq=6631 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997573 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15853 bytes_read=624941 bytes_retransmit=9 bytes_invalid=0 send_seq=2588 receive_seq=2588 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997721 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16393 bytes_read=49229 bytes_retransmit=9 bytes_invalid=0 send_seq=2579 receive_seq=2579 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999454 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=30.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64965 bytes_read=1093799 bytes_retransmit=0 bytes_invalid=0 send_seq=6676 receive_seq=6676 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998695 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=47.0 th1: temp=48.7 th2: temp=52.1 th3: temp=50.0 sysload=0.47 cputime=225.544 memavail=7370076 print_time=2476.821 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2461.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=19916190 bytes_read=2439534 bytes_retransmit=9 bytes_invalid=0 send_seq=347218 receive_seq=347218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015672 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=15646 bytes_read=50210 bytes_retransmit=0 bytes_invalid=0 send_seq=2579 receive_seq=2579 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997381 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=109212 bytes_read=3483187 bytes_retransmit=9 bytes_invalid=0 send_seq=14779 receive_seq=14779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997763 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51560 bytes_read=1038770 bytes_retransmit=9 bytes_invalid=0 send_seq=6632 receive_seq=6632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997576 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15859 bytes_read=625175 bytes_retransmit=9 bytes_invalid=0 send_seq=2589 receive_seq=2589 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997717 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16399 bytes_read=49256 bytes_retransmit=9 bytes_invalid=0 send_seq=2580 receive_seq=2580 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=30.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64971 bytes_read=1094155 bytes_retransmit=0 bytes_invalid=0 send_seq=6677 receive_seq=6677 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998691 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=47.2 th1: temp=48.7 th2: temp=52.0 th3: temp=50.1 sysload=0.47 cputime=225.607 memavail=7371852 print_time=2476.821 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Command {generate_tension_graphs} finished

toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Activating extruder extruder
Extruder 'extruder' now syncing with 'extruder'
Extruder 'extruder1' now syncing with 'extruder1'
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 2462.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=19916581 bytes_read=2439969 bytes_retransmit=9 bytes_invalid=0 send_seq=347243 receive_seq=347243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015671 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=15652 bytes_read=50226 bytes_retransmit=0 bytes_invalid=0 send_seq=2580 receive_seq=2580 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997409 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=109218 bytes_read=3483280 bytes_retransmit=9 bytes_invalid=0 send_seq=14780 receive_seq=14780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997791 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51566 bytes_read=1038863 bytes_retransmit=9 bytes_invalid=0 send_seq=6633 receive_seq=6633 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997691 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15865 bytes_read=625409 bytes_retransmit=9 bytes_invalid=0 send_seq=2590 receive_seq=2590 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997735 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16405 bytes_read=49272 bytes_retransmit=9 bytes_invalid=0 send_seq=2581 receive_seq=2581 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=30.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64977 bytes_read=1094511 bytes_retransmit=0 bytes_invalid=0 send_seq=6678 receive_seq=6678 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998695 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.7 th1: temp=48.7 th2: temp=52.2 th3: temp=50.1 sysload=0.43 cputime=225.761 memavail=7398252 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2463.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=19916874 bytes_read=2440403 bytes_retransmit=9 bytes_invalid=0 send_seq=347265 receive_seq=347265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015687 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=15658 bytes_read=50242 bytes_retransmit=0 bytes_invalid=0 send_seq=2581 receive_seq=2581 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997395 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=109224 bytes_read=3483403 bytes_retransmit=9 bytes_invalid=0 send_seq=14781 receive_seq=14781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997831 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=51572 bytes_read=1039000 bytes_retransmit=9 bytes_invalid=0 send_seq=6634 receive_seq=6634 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997840 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15871 bytes_read=625703 bytes_retransmit=9 bytes_invalid=0 send_seq=2591 receive_seq=2591 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997727 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16411 bytes_read=49288 bytes_retransmit=9 bytes_invalid=0 send_seq=2582 receive_seq=2582 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999456 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64983 bytes_read=1094867 bytes_retransmit=0 bytes_invalid=0 send_seq=6679 receive_seq=6679 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998689 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.6 th1: temp=48.4 th2: temp=51.9 th3: temp=50.2 sysload=0.43 cputime=225.805 memavail=7398004 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2464.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=19917172 bytes_read=2440843 bytes_retransmit=9 bytes_invalid=0 send_seq=347288 receive_seq=347288 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015689 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=15664 bytes_read=50258 bytes_retransmit=0 bytes_invalid=0 send_seq=2582 receive_seq=2582 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997325 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=109230 bytes_read=3483503 bytes_retransmit=9 bytes_invalid=0 send_seq=14782 receive_seq=14782 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997809 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=51578 bytes_read=1039100 bytes_retransmit=9 bytes_invalid=0 send_seq=6635 receive_seq=6635 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997703 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15877 bytes_read=625937 bytes_retransmit=9 bytes_invalid=0 send_seq=2592 receive_seq=2592 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16417 bytes_read=49304 bytes_retransmit=9 bytes_invalid=0 send_seq=2583 receive_seq=2583 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64989 bytes_read=1095223 bytes_retransmit=0 bytes_invalid=0 send_seq=6680 receive_seq=6680 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998661 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=47.0 th1: temp=48.7 th2: temp=52.2 th3: temp=50.4 sysload=0.43 cputime=225.847 memavail=7397752 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2465.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19917465 bytes_read=2441278 bytes_retransmit=9 bytes_invalid=0 send_seq=347310 receive_seq=347310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015689 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=15670 bytes_read=50287 bytes_retransmit=0 bytes_invalid=0 send_seq=2583 receive_seq=2583 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997315 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=109236 bytes_read=3483617 bytes_retransmit=9 bytes_invalid=0 send_seq=14783 receive_seq=14783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997753 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=51584 bytes_read=1039200 bytes_retransmit=9 bytes_invalid=0 send_seq=6636 receive_seq=6636 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997632 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=15883 bytes_read=626201 bytes_retransmit=9 bytes_invalid=0 send_seq=2593 receive_seq=2593 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16423 bytes_read=49320 bytes_retransmit=9 bytes_invalid=0 send_seq=2584 receive_seq=2584 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=64995 bytes_read=1095579 bytes_retransmit=0 bytes_invalid=0 send_seq=6681 receive_seq=6681 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998661 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.6 th1: temp=48.4 th2: temp=52.4 th3: temp=50.4 sysload=0.43 cputime=225.889 memavail=7397288 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2466.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19917763 bytes_read=2441717 bytes_retransmit=9 bytes_invalid=0 send_seq=347333 receive_seq=347333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015686 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=15676 bytes_read=50303 bytes_retransmit=0 bytes_invalid=0 send_seq=2584 receive_seq=2584 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997295 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=109242 bytes_read=3483745 bytes_retransmit=9 bytes_invalid=0 send_seq=14784 receive_seq=14784 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997722 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=51590 bytes_read=1039328 bytes_retransmit=9 bytes_invalid=0 send_seq=6637 receive_seq=6637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997586 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=15889 bytes_read=626480 bytes_retransmit=9 bytes_invalid=0 send_seq=2594 receive_seq=2594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16429 bytes_read=49347 bytes_retransmit=9 bytes_invalid=0 send_seq=2585 receive_seq=2585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65001 bytes_read=1095935 bytes_retransmit=0 bytes_invalid=0 send_seq=6682 receive_seq=6682 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998687 coil_temp=17.5 refs=0 mcu_temp=20.66 supply_voltage=3.012 th0: temp=46.8 th1: temp=48.5 th2: temp=52.3 th3: temp=50.3 sysload=0.43 cputime=225.932 memavail=7397288 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2467.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19918061 bytes_read=2442157 bytes_retransmit=9 bytes_invalid=0 send_seq=347356 receive_seq=347356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015690 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=15682 bytes_read=50319 bytes_retransmit=0 bytes_invalid=0 send_seq=2585 receive_seq=2585 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997286 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=109248 bytes_read=3483845 bytes_retransmit=9 bytes_invalid=0 send_seq=14785 receive_seq=14785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997698 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=51596 bytes_read=1039428 bytes_retransmit=9 bytes_invalid=0 send_seq=6638 receive_seq=6638 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=15895 bytes_read=626714 bytes_retransmit=9 bytes_invalid=0 send_seq=2595 receive_seq=2595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997689 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16435 bytes_read=49363 bytes_retransmit=9 bytes_invalid=0 send_seq=2586 receive_seq=2586 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65007 bytes_read=1096291 bytes_retransmit=0 bytes_invalid=0 send_seq=6683 receive_seq=6683 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998675 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=46.6 th1: temp=48.0 th2: temp=52.4 th3: temp=50.4 sysload=0.40 cputime=225.974 memavail=7397288 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2468.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19918354 bytes_read=2442575 bytes_retransmit=9 bytes_invalid=0 send_seq=347378 receive_seq=347378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015688 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=15688 bytes_read=50335 bytes_retransmit=0 bytes_invalid=0 send_seq=2586 receive_seq=2586 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997274 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=109254 bytes_read=3483959 bytes_retransmit=9 bytes_invalid=0 send_seq=14786 receive_seq=14786 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997668 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51602 bytes_read=1039542 bytes_retransmit=9 bytes_invalid=0 send_seq=6639 receive_seq=6639 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997535 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=15901 bytes_read=626963 bytes_retransmit=9 bytes_invalid=0 send_seq=2596 receive_seq=2596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16441 bytes_read=49379 bytes_retransmit=9 bytes_invalid=0 send_seq=2587 receive_seq=2587 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65013 bytes_read=1096647 bytes_retransmit=0 bytes_invalid=0 send_seq=6684 receive_seq=6684 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998674 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=46.6 th1: temp=47.9 th2: temp=52.3 th3: temp=50.7 sysload=0.40 cputime=226.016 memavail=7397304 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2469.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19918622 bytes_read=2442982 bytes_retransmit=9 bytes_invalid=0 send_seq=347395 receive_seq=347395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015688 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=15694 bytes_read=50351 bytes_retransmit=0 bytes_invalid=0 send_seq=2587 receive_seq=2587 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997269 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=109260 bytes_read=3484073 bytes_retransmit=9 bytes_invalid=0 send_seq=14787 receive_seq=14787 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997662 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51608 bytes_read=1039670 bytes_retransmit=9 bytes_invalid=0 send_seq=6640 receive_seq=6640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997544 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=15907 bytes_read=627242 bytes_retransmit=9 bytes_invalid=0 send_seq=2597 receive_seq=2597 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16447 bytes_read=49395 bytes_retransmit=9 bytes_invalid=0 send_seq=2588 receive_seq=2588 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65019 bytes_read=1097003 bytes_retransmit=0 bytes_invalid=0 send_seq=6685 receive_seq=6685 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998674 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=46.4 th1: temp=48.0 th2: temp=52.4 th3: temp=50.5 sysload=0.40 cputime=226.059 memavail=7397304 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2470.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19918920 bytes_read=2443437 bytes_retransmit=9 bytes_invalid=0 send_seq=347418 receive_seq=347418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015687 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15700 bytes_read=50380 bytes_retransmit=0 bytes_invalid=0 send_seq=2588 receive_seq=2588 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997263 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=109266 bytes_read=3484173 bytes_retransmit=9 bytes_invalid=0 send_seq=14788 receive_seq=14788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997654 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51614 bytes_read=1039770 bytes_retransmit=9 bytes_invalid=0 send_seq=6641 receive_seq=6641 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997549 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15913 bytes_read=627491 bytes_retransmit=9 bytes_invalid=0 send_seq=2598 receive_seq=2598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997714 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16453 bytes_read=49411 bytes_retransmit=9 bytes_invalid=0 send_seq=2589 receive_seq=2589 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65025 bytes_read=1097343 bytes_retransmit=0 bytes_invalid=0 send_seq=6686 receive_seq=6686 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998674 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=46.2 th1: temp=48.0 th2: temp=52.6 th3: temp=50.6 sysload=0.40 cputime=226.102 memavail=7397304 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2471.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19919218 bytes_read=2443862 bytes_retransmit=9 bytes_invalid=0 send_seq=347441 receive_seq=347441 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015687 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15706 bytes_read=50396 bytes_retransmit=0 bytes_invalid=0 send_seq=2589 receive_seq=2589 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997260 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109272 bytes_read=3484301 bytes_retransmit=9 bytes_invalid=0 send_seq=14789 receive_seq=14789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997648 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51620 bytes_read=1039870 bytes_retransmit=9 bytes_invalid=0 send_seq=6642 receive_seq=6642 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15919 bytes_read=627740 bytes_retransmit=9 bytes_invalid=0 send_seq=2599 receive_seq=2599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997703 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16459 bytes_read=49438 bytes_retransmit=9 bytes_invalid=0 send_seq=2590 receive_seq=2590 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65031 bytes_read=1097699 bytes_retransmit=0 bytes_invalid=0 send_seq=6687 receive_seq=6687 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998677 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=46.1 th1: temp=47.6 th2: temp=52.7 th3: temp=50.6 sysload=0.40 cputime=226.145 memavail=7397304 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2472.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19919516 bytes_read=2444316 bytes_retransmit=9 bytes_invalid=0 send_seq=347464 receive_seq=347464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015687 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15712 bytes_read=50412 bytes_retransmit=0 bytes_invalid=0 send_seq=2590 receive_seq=2590 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997255 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109278 bytes_read=3484415 bytes_retransmit=9 bytes_invalid=0 send_seq=14790 receive_seq=14790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997651 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51626 bytes_read=1039998 bytes_retransmit=9 bytes_invalid=0 send_seq=6643 receive_seq=6643 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15925 bytes_read=628019 bytes_retransmit=9 bytes_invalid=0 send_seq=2600 receive_seq=2600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997682 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16465 bytes_read=49454 bytes_retransmit=9 bytes_invalid=0 send_seq=2591 receive_seq=2591 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65037 bytes_read=1098055 bytes_retransmit=0 bytes_invalid=0 send_seq=6688 receive_seq=6688 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998700 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.4 th1: temp=47.6 th2: temp=52.6 th3: temp=50.8 sysload=0.45 cputime=226.188 memavail=7397304 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2473.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19919814 bytes_read=2444741 bytes_retransmit=9 bytes_invalid=0 send_seq=347487 receive_seq=347487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015692 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15718 bytes_read=50428 bytes_retransmit=0 bytes_invalid=0 send_seq=2591 receive_seq=2591 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997243 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109284 bytes_read=3484515 bytes_retransmit=9 bytes_invalid=0 send_seq=14791 receive_seq=14791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997667 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51632 bytes_read=1040112 bytes_retransmit=9 bytes_invalid=0 send_seq=6644 receive_seq=6644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15931 bytes_read=628253 bytes_retransmit=9 bytes_invalid=0 send_seq=2601 receive_seq=2601 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16471 bytes_read=49470 bytes_retransmit=9 bytes_invalid=0 send_seq=2592 receive_seq=2592 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65043 bytes_read=1098411 bytes_retransmit=0 bytes_invalid=0 send_seq=6689 receive_seq=6689 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998682 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.4 th1: temp=47.7 th2: temp=52.6 th3: temp=50.8 sysload=0.45 cputime=226.232 memavail=7397304 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Stats 2474.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19920107 bytes_read=2445161 bytes_retransmit=9 bytes_invalid=0 send_seq=347509 receive_seq=347509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015694 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15724 bytes_read=50444 bytes_retransmit=0 bytes_invalid=0 send_seq=2592 receive_seq=2592 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997229 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109290 bytes_read=3484629 bytes_retransmit=9 bytes_invalid=0 send_seq=14792 receive_seq=14792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997671 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51638 bytes_read=1040212 bytes_retransmit=9 bytes_invalid=0 send_seq=6645 receive_seq=6645 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15937 bytes_read=628502 bytes_retransmit=9 bytes_invalid=0 send_seq=2602 receive_seq=2602 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16477 bytes_read=49486 bytes_retransmit=9 bytes_invalid=0 send_seq=2593 receive_seq=2593 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65049 bytes_read=1098767 bytes_retransmit=0 bytes_invalid=0 send_seq=6690 receive_seq=6690 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998669 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.1 th1: temp=47.3 th2: temp=52.6 th3: temp=50.8 sysload=0.45 cputime=226.277 memavail=7397320 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2475.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19920405 bytes_read=2445630 bytes_retransmit=9 bytes_invalid=0 send_seq=347532 receive_seq=347532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015695 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15730 bytes_read=50473 bytes_retransmit=0 bytes_invalid=0 send_seq=2593 receive_seq=2593 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997240 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109296 bytes_read=3484743 bytes_retransmit=9 bytes_invalid=0 send_seq=14793 receive_seq=14793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997656 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51644 bytes_read=1040340 bytes_retransmit=9 bytes_invalid=0 send_seq=6646 receive_seq=6646 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=15943 bytes_read=628796 bytes_retransmit=9 bytes_invalid=0 send_seq=2603 receive_seq=2603 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16483 bytes_read=49502 bytes_retransmit=9 bytes_invalid=0 send_seq=2594 receive_seq=2594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65055 bytes_read=1099123 bytes_retransmit=0 bytes_invalid=0 send_seq=6691 receive_seq=6691 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998660 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.4 th1: temp=47.4 th2: temp=52.8 th3: temp=50.8 sysload=0.45 cputime=226.323 memavail=7397480 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2476.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19920703 bytes_read=2446055 bytes_retransmit=9 bytes_invalid=0 send_seq=347555 receive_seq=347555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015695 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15736 bytes_read=50489 bytes_retransmit=0 bytes_invalid=0 send_seq=2594 receive_seq=2594 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997239 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109302 bytes_read=3484857 bytes_retransmit=9 bytes_invalid=0 send_seq=14794 receive_seq=14794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997645 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51650 bytes_read=1040440 bytes_retransmit=9 bytes_invalid=0 send_seq=6647 receive_seq=6647 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997526 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=15949 bytes_read=629030 bytes_retransmit=9 bytes_invalid=0 send_seq=2604 receive_seq=2604 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16489 bytes_read=49529 bytes_retransmit=9 bytes_invalid=0 send_seq=2595 receive_seq=2595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65061 bytes_read=1099479 bytes_retransmit=0 bytes_invalid=0 send_seq=6692 receive_seq=6692 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998661 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=46.3 th1: temp=47.3 th2: temp=52.8 th3: temp=50.9 sysload=0.45 cputime=226.373 memavail=7391552 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2477.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19920996 bytes_read=2446475 bytes_retransmit=9 bytes_invalid=0 send_seq=347577 receive_seq=347577 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015697 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15742 bytes_read=50505 bytes_retransmit=0 bytes_invalid=0 send_seq=2595 receive_seq=2595 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997237 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109308 bytes_read=3484971 bytes_retransmit=9 bytes_invalid=0 send_seq=14795 receive_seq=14795 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997646 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51656 bytes_read=1040540 bytes_retransmit=9 bytes_invalid=0 send_seq=6648 receive_seq=6648 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997592 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=15955 bytes_read=629279 bytes_retransmit=9 bytes_invalid=0 send_seq=2605 receive_seq=2605 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16495 bytes_read=49545 bytes_retransmit=9 bytes_invalid=0 send_seq=2596 receive_seq=2596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65067 bytes_read=1099835 bytes_retransmit=0 bytes_invalid=0 send_seq=6693 receive_seq=6693 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998664 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=46.0 th1: temp=47.3 th2: temp=52.9 th3: temp=50.9 sysload=0.41 cputime=226.417 memavail=7397204 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2478.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19921294 bytes_read=2446929 bytes_retransmit=9 bytes_invalid=0 send_seq=347600 receive_seq=347600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015696 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15748 bytes_read=50521 bytes_retransmit=0 bytes_invalid=0 send_seq=2596 receive_seq=2596 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997251 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109314 bytes_read=3485085 bytes_retransmit=9 bytes_invalid=0 send_seq=14796 receive_seq=14796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997664 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51662 bytes_read=1040682 bytes_retransmit=9 bytes_invalid=0 send_seq=6649 receive_seq=6649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997550 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=15961 bytes_read=629558 bytes_retransmit=9 bytes_invalid=0 send_seq=2606 receive_seq=2606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16501 bytes_read=49561 bytes_retransmit=9 bytes_invalid=0 send_seq=2597 receive_seq=2597 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65073 bytes_read=1100191 bytes_retransmit=0 bytes_invalid=0 send_seq=6694 receive_seq=6694 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998656 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=46.4 th1: temp=47.1 th2: temp=52.8 th3: temp=51.0 sysload=0.41 cputime=226.460 memavail=7397204 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2479.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19921592 bytes_read=2447350 bytes_retransmit=9 bytes_invalid=0 send_seq=347623 receive_seq=347623 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015700 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15754 bytes_read=50537 bytes_retransmit=0 bytes_invalid=0 send_seq=2597 receive_seq=2597 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997249 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109320 bytes_read=3485185 bytes_retransmit=9 bytes_invalid=0 send_seq=14797 receive_seq=14797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997660 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51668 bytes_read=1040782 bytes_retransmit=9 bytes_invalid=0 send_seq=6650 receive_seq=6650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=15967 bytes_read=629792 bytes_retransmit=9 bytes_invalid=0 send_seq=2607 receive_seq=2607 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997677 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16507 bytes_read=49577 bytes_retransmit=9 bytes_invalid=0 send_seq=2598 receive_seq=2598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65079 bytes_read=1100547 bytes_retransmit=0 bytes_invalid=0 send_seq=6695 receive_seq=6695 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998740 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=45.9 th1: temp=47.3 th2: temp=53.0 th3: temp=50.7 sysload=0.41 cputime=226.503 memavail=7397204 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2480.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19921890 bytes_read=2447790 bytes_retransmit=9 bytes_invalid=0 send_seq=347646 receive_seq=347646 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015703 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15760 bytes_read=50566 bytes_retransmit=0 bytes_invalid=0 send_seq=2598 receive_seq=2598 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997237 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109326 bytes_read=3485299 bytes_retransmit=9 bytes_invalid=0 send_seq=14798 receive_seq=14798 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997655 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51674 bytes_read=1040896 bytes_retransmit=9 bytes_invalid=0 send_seq=6651 receive_seq=6651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997494 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15973 bytes_read=630056 bytes_retransmit=9 bytes_invalid=0 send_seq=2608 receive_seq=2608 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16513 bytes_read=49593 bytes_retransmit=9 bytes_invalid=0 send_seq=2599 receive_seq=2599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65085 bytes_read=1100903 bytes_retransmit=0 bytes_invalid=0 send_seq=6696 receive_seq=6696 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998708 coil_temp=17.5 refs=0 mcu_temp=20.66 supply_voltage=3.012 th0: temp=46.2 th1: temp=47.2 th2: temp=52.9 th3: temp=50.9 sysload=0.41 cputime=226.546 memavail=7397204 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2481.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19922188 bytes_read=2448244 bytes_retransmit=9 bytes_invalid=0 send_seq=347669 receive_seq=347669 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015711 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15766 bytes_read=50582 bytes_retransmit=0 bytes_invalid=0 send_seq=2599 receive_seq=2599 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997226 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109332 bytes_read=3485427 bytes_retransmit=9 bytes_invalid=0 send_seq=14799 receive_seq=14799 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997645 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51680 bytes_read=1041010 bytes_retransmit=9 bytes_invalid=0 send_seq=6652 receive_seq=6652 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997477 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15979 bytes_read=630327 bytes_retransmit=9 bytes_invalid=0 send_seq=2609 receive_seq=2609 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16519 bytes_read=49620 bytes_retransmit=9 bytes_invalid=0 send_seq=2600 receive_seq=2600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65091 bytes_read=1101259 bytes_retransmit=0 bytes_invalid=0 send_seq=6697 receive_seq=6697 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998700 coil_temp=17.5 refs=0 mcu_temp=20.66 supply_voltage=3.012 th0: temp=46.2 th1: temp=47.0 th2: temp=53.1 th3: temp=51.0 sysload=0.41 cputime=226.590 memavail=7397220 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2482.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19922486 bytes_read=2448669 bytes_retransmit=9 bytes_invalid=0 send_seq=347692 receive_seq=347692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015714 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15772 bytes_read=50598 bytes_retransmit=0 bytes_invalid=0 send_seq=2600 receive_seq=2600 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997266 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109338 bytes_read=3485527 bytes_retransmit=9 bytes_invalid=0 send_seq=14800 receive_seq=14800 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997628 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51686 bytes_read=1041110 bytes_retransmit=9 bytes_invalid=0 send_seq=6653 receive_seq=6653 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15985 bytes_read=630544 bytes_retransmit=9 bytes_invalid=0 send_seq=2610 receive_seq=2610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16525 bytes_read=49636 bytes_retransmit=9 bytes_invalid=0 send_seq=2601 receive_seq=2601 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999467 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65097 bytes_read=1101615 bytes_retransmit=0 bytes_invalid=0 send_seq=6698 receive_seq=6698 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998689 coil_temp=17.5 refs=0 mcu_temp=20.66 supply_voltage=3.012 th0: temp=46.3 th1: temp=46.8 th2: temp=53.0 th3: temp=50.9 sysload=0.38 cputime=226.632 memavail=7397220 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2483.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19922779 bytes_read=2449089 bytes_retransmit=9 bytes_invalid=0 send_seq=347714 receive_seq=347714 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015723 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15778 bytes_read=50614 bytes_retransmit=0 bytes_invalid=0 send_seq=2601 receive_seq=2601 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997248 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109344 bytes_read=3485641 bytes_retransmit=9 bytes_invalid=0 send_seq=14801 receive_seq=14801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997626 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51692 bytes_read=1041238 bytes_retransmit=9 bytes_invalid=0 send_seq=6654 receive_seq=6654 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997488 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15991 bytes_read=630776 bytes_retransmit=9 bytes_invalid=0 send_seq=2611 receive_seq=2611 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16531 bytes_read=49652 bytes_retransmit=9 bytes_invalid=0 send_seq=2602 receive_seq=2602 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999459 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65103 bytes_read=1101971 bytes_retransmit=0 bytes_invalid=0 send_seq=6699 receive_seq=6699 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998680 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.1 th1: temp=47.2 th2: temp=52.9 th3: temp=51.1 sysload=0.38 cputime=226.674 memavail=7397220 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2484.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19923077 bytes_read=2449543 bytes_retransmit=9 bytes_invalid=0 send_seq=347737 receive_seq=347737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015724 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15784 bytes_read=50630 bytes_retransmit=0 bytes_invalid=0 send_seq=2602 receive_seq=2602 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997228 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109350 bytes_read=3485755 bytes_retransmit=9 bytes_invalid=0 send_seq=14802 receive_seq=14802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997619 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51698 bytes_read=1041352 bytes_retransmit=9 bytes_invalid=0 send_seq=6655 receive_seq=6655 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997469 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=15997 bytes_read=631036 bytes_retransmit=9 bytes_invalid=0 send_seq=2612 receive_seq=2612 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16537 bytes_read=49668 bytes_retransmit=9 bytes_invalid=0 send_seq=2603 receive_seq=2603 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999455 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65109 bytes_read=1102327 bytes_retransmit=0 bytes_invalid=0 send_seq=6700 receive_seq=6700 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998663 coil_temp=17.5 refs=0 mcu_temp=20.66 supply_voltage=3.012 th0: temp=46.1 th1: temp=46.6 th2: temp=53.0 th3: temp=51.1 sysload=0.38 cputime=226.718 memavail=7397220 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2485.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19923375 bytes_read=2449983 bytes_retransmit=9 bytes_invalid=0 send_seq=347760 receive_seq=347760 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015731 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15790 bytes_read=50659 bytes_retransmit=0 bytes_invalid=0 send_seq=2603 receive_seq=2603 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997226 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109356 bytes_read=3485855 bytes_retransmit=9 bytes_invalid=0 send_seq=14803 receive_seq=14803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997628 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51704 bytes_read=1041452 bytes_retransmit=9 bytes_invalid=0 send_seq=6656 receive_seq=6656 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997461 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=16003 bytes_read=631269 bytes_retransmit=9 bytes_invalid=0 send_seq=2613 receive_seq=2613 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16543 bytes_read=49684 bytes_retransmit=9 bytes_invalid=0 send_seq=2604 receive_seq=2604 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999475 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65115 bytes_read=1102683 bytes_retransmit=0 bytes_invalid=0 send_seq=6701 receive_seq=6701 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998690 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=46.1 th1: temp=46.8 th2: temp=53.2 th3: temp=51.1 sysload=0.38 cputime=226.762 memavail=7397260 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2486.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19923673 bytes_read=2450408 bytes_retransmit=9 bytes_invalid=0 send_seq=347783 receive_seq=347783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015734 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15796 bytes_read=50675 bytes_retransmit=0 bytes_invalid=0 send_seq=2604 receive_seq=2604 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997215 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109362 bytes_read=3485983 bytes_retransmit=9 bytes_invalid=0 send_seq=14804 receive_seq=14804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997705 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51710 bytes_read=1041566 bytes_retransmit=9 bytes_invalid=0 send_seq=6657 receive_seq=6657 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997465 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=16009 bytes_read=631502 bytes_retransmit=9 bytes_invalid=0 send_seq=2614 receive_seq=2614 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997626 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16549 bytes_read=49711 bytes_retransmit=9 bytes_invalid=0 send_seq=2605 receive_seq=2605 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999463 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65121 bytes_read=1103039 bytes_retransmit=0 bytes_invalid=0 send_seq=6702 receive_seq=6702 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998675 coil_temp=17.5 refs=0 mcu_temp=20.66 supply_voltage=3.012 th0: temp=46.0 th1: temp=46.8 th2: temp=53.2 th3: temp=51.3 sysload=0.38 cputime=226.805 memavail=7397052 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2487.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19923971 bytes_read=2450862 bytes_retransmit=9 bytes_invalid=0 send_seq=347806 receive_seq=347806 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015736 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15802 bytes_read=50691 bytes_retransmit=0 bytes_invalid=0 send_seq=2605 receive_seq=2605 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997206 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109368 bytes_read=3486097 bytes_retransmit=9 bytes_invalid=0 send_seq=14805 receive_seq=14805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997696 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51716 bytes_read=1041680 bytes_retransmit=9 bytes_invalid=0 send_seq=6658 receive_seq=6658 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997465 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=16015 bytes_read=631781 bytes_retransmit=9 bytes_invalid=0 send_seq=2615 receive_seq=2615 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16555 bytes_read=49727 bytes_retransmit=9 bytes_invalid=0 send_seq=2606 receive_seq=2606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999466 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65127 bytes_read=1103395 bytes_retransmit=0 bytes_invalid=0 send_seq=6703 receive_seq=6703 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998712 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.0 th1: temp=46.9 th2: temp=53.1 th3: temp=51.1 sysload=0.35 cputime=226.849 memavail=7397052 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2488.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19924269 bytes_read=2451287 bytes_retransmit=9 bytes_invalid=0 send_seq=347829 receive_seq=347829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015742 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15808 bytes_read=50707 bytes_retransmit=0 bytes_invalid=0 send_seq=2606 receive_seq=2606 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997211 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109374 bytes_read=3486197 bytes_retransmit=9 bytes_invalid=0 send_seq=14806 receive_seq=14806 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997757 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51722 bytes_read=1041794 bytes_retransmit=9 bytes_invalid=0 send_seq=6659 receive_seq=6659 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997458 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=16021 bytes_read=632015 bytes_retransmit=9 bytes_invalid=0 send_seq=2616 receive_seq=2616 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16561 bytes_read=49743 bytes_retransmit=9 bytes_invalid=0 send_seq=2607 receive_seq=2607 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999457 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65133 bytes_read=1103751 bytes_retransmit=0 bytes_invalid=0 send_seq=6704 receive_seq=6704 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998714 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.1 th1: temp=46.7 th2: temp=53.1 th3: temp=51.3 sysload=0.35 cputime=226.893 memavail=7397052 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2489.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19924567 bytes_read=2451712 bytes_retransmit=9 bytes_invalid=0 send_seq=347852 receive_seq=347852 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015751 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15814 bytes_read=50723 bytes_retransmit=0 bytes_invalid=0 send_seq=2607 receive_seq=2607 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997214 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109380 bytes_read=3486311 bytes_retransmit=9 bytes_invalid=0 send_seq=14807 receive_seq=14807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997707 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51728 bytes_read=1041908 bytes_retransmit=9 bytes_invalid=0 send_seq=6660 receive_seq=6660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997447 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=16027 bytes_read=632264 bytes_retransmit=9 bytes_invalid=0 send_seq=2617 receive_seq=2617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16567 bytes_read=49759 bytes_retransmit=9 bytes_invalid=0 send_seq=2608 receive_seq=2608 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65139 bytes_read=1104107 bytes_retransmit=0 bytes_invalid=0 send_seq=6705 receive_seq=6705 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998679 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=45.9 th1: temp=46.8 th2: temp=53.1 th3: temp=51.3 sysload=0.35 cputime=226.935 memavail=7397052 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2490.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19924865 bytes_read=2452175 bytes_retransmit=9 bytes_invalid=0 send_seq=347875 receive_seq=347875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015752 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15820 bytes_read=50752 bytes_retransmit=0 bytes_invalid=0 send_seq=2608 receive_seq=2608 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997254 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109386 bytes_read=3486425 bytes_retransmit=9 bytes_invalid=0 send_seq=14808 receive_seq=14808 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997663 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51734 bytes_read=1042022 bytes_retransmit=9 bytes_invalid=0 send_seq=6661 receive_seq=6661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997431 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16033 bytes_read=632558 bytes_retransmit=9 bytes_invalid=0 send_seq=2618 receive_seq=2618 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997623 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16573 bytes_read=49775 bytes_retransmit=9 bytes_invalid=0 send_seq=2609 receive_seq=2609 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999456 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65145 bytes_read=1104463 bytes_retransmit=0 bytes_invalid=0 send_seq=6706 receive_seq=6706 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998650 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=45.7 th1: temp=46.8 th2: temp=53.3 th3: temp=51.3 sysload=0.35 cputime=226.980 memavail=7397052 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2491.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19925163 bytes_read=2452600 bytes_retransmit=9 bytes_invalid=0 send_seq=347898 receive_seq=347898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015756 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15826 bytes_read=50768 bytes_retransmit=0 bytes_invalid=0 send_seq=2609 receive_seq=2609 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997266 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109392 bytes_read=3486539 bytes_retransmit=9 bytes_invalid=0 send_seq=14809 receive_seq=14809 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997658 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51740 bytes_read=1042122 bytes_retransmit=9 bytes_invalid=0 send_seq=6662 receive_seq=6662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997441 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16039 bytes_read=632792 bytes_retransmit=9 bytes_invalid=0 send_seq=2619 receive_seq=2619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16579 bytes_read=49802 bytes_retransmit=9 bytes_invalid=0 send_seq=2610 receive_seq=2610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999449 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65151 bytes_read=1104819 bytes_retransmit=0 bytes_invalid=0 send_seq=6707 receive_seq=6707 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998638 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=45.9 th1: temp=46.6 th2: temp=53.4 th3: temp=51.3 sysload=0.35 cputime=227.024 memavail=7397216 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2492.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19925461 bytes_read=2453025 bytes_retransmit=9 bytes_invalid=0 send_seq=347921 receive_seq=347921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015756 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15832 bytes_read=50784 bytes_retransmit=0 bytes_invalid=0 send_seq=2610 receive_seq=2610 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997261 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109398 bytes_read=3486653 bytes_retransmit=9 bytes_invalid=0 send_seq=14810 receive_seq=14810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997744 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51746 bytes_read=1042236 bytes_retransmit=9 bytes_invalid=0 send_seq=6663 receive_seq=6663 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997440 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16045 bytes_read=633056 bytes_retransmit=9 bytes_invalid=0 send_seq=2620 receive_seq=2620 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16585 bytes_read=49818 bytes_retransmit=9 bytes_invalid=0 send_seq=2611 receive_seq=2611 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65157 bytes_read=1105175 bytes_retransmit=0 bytes_invalid=0 send_seq=6708 receive_seq=6708 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998661 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=45.7 th1: temp=46.7 th2: temp=53.2 th3: temp=51.5 sysload=0.32 cputime=227.068 memavail=7397320 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2493.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19925759 bytes_read=2453479 bytes_retransmit=9 bytes_invalid=0 send_seq=347944 receive_seq=347944 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015760 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15838 bytes_read=50800 bytes_retransmit=0 bytes_invalid=0 send_seq=2611 receive_seq=2611 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997251 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109404 bytes_read=3486767 bytes_retransmit=9 bytes_invalid=0 send_seq=14811 receive_seq=14811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997711 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51752 bytes_read=1042364 bytes_retransmit=9 bytes_invalid=0 send_seq=6664 receive_seq=6664 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997454 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16051 bytes_read=633320 bytes_retransmit=9 bytes_invalid=0 send_seq=2621 receive_seq=2621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16591 bytes_read=49834 bytes_retransmit=9 bytes_invalid=0 send_seq=2612 receive_seq=2612 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65163 bytes_read=1105531 bytes_retransmit=0 bytes_invalid=0 send_seq=6709 receive_seq=6709 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998653 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.0 th1: temp=46.7 th2: temp=53.2 th3: temp=51.4 sysload=0.32 cputime=227.120 memavail=7390772 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2494.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19926057 bytes_read=2453904 bytes_retransmit=9 bytes_invalid=0 send_seq=347967 receive_seq=347967 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015763 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15844 bytes_read=50816 bytes_retransmit=0 bytes_invalid=0 send_seq=2612 receive_seq=2612 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997224 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109410 bytes_read=3486867 bytes_retransmit=9 bytes_invalid=0 send_seq=14812 receive_seq=14812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997685 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51758 bytes_read=1042464 bytes_retransmit=9 bytes_invalid=0 send_seq=6665 receive_seq=6665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997450 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16057 bytes_read=633554 bytes_retransmit=9 bytes_invalid=0 send_seq=2622 receive_seq=2622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16597 bytes_read=49850 bytes_retransmit=9 bytes_invalid=0 send_seq=2613 receive_seq=2613 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65169 bytes_read=1105887 bytes_retransmit=0 bytes_invalid=0 send_seq=6710 receive_seq=6710 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998641 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.1 th1: temp=46.7 th2: temp=53.1 th3: temp=51.6 sysload=0.32 cputime=227.166 memavail=7396712 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2495.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19926355 bytes_read=2454344 bytes_retransmit=9 bytes_invalid=0 send_seq=347990 receive_seq=347990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015765 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15850 bytes_read=50832 bytes_retransmit=0 bytes_invalid=0 send_seq=2613 receive_seq=2613 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997243 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109416 bytes_read=3486981 bytes_retransmit=9 bytes_invalid=0 send_seq=14813 receive_seq=14813 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997662 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51764 bytes_read=1042578 bytes_retransmit=9 bytes_invalid=0 send_seq=6666 receive_seq=6666 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997448 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16063 bytes_read=633833 bytes_retransmit=9 bytes_invalid=0 send_seq=2623 receive_seq=2623 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16603 bytes_read=49866 bytes_retransmit=9 bytes_invalid=0 send_seq=2614 receive_seq=2614 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65175 bytes_read=1106243 bytes_retransmit=0 bytes_invalid=0 send_seq=6711 receive_seq=6711 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998630 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.0 th1: temp=46.4 th2: temp=53.4 th3: temp=51.4 sysload=0.32 cputime=227.211 memavail=7396008 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2496.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19926653 bytes_read=2454798 bytes_retransmit=9 bytes_invalid=0 send_seq=348013 receive_seq=348013 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015766 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15856 bytes_read=50861 bytes_retransmit=0 bytes_invalid=0 send_seq=2614 receive_seq=2614 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997233 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109422 bytes_read=3487109 bytes_retransmit=9 bytes_invalid=0 send_seq=14814 receive_seq=14814 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997648 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51770 bytes_read=1042692 bytes_retransmit=9 bytes_invalid=0 send_seq=6667 receive_seq=6667 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997452 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16069 bytes_read=634097 bytes_retransmit=9 bytes_invalid=0 send_seq=2624 receive_seq=2624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997629 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16609 bytes_read=49893 bytes_retransmit=9 bytes_invalid=0 send_seq=2615 receive_seq=2615 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999449 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65181 bytes_read=1106599 bytes_retransmit=0 bytes_invalid=0 send_seq=6712 receive_seq=6712 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998625 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.1 th1: temp=46.8 th2: temp=53.4 th3: temp=51.4 sysload=0.32 cputime=227.257 memavail=7396028 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2497.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19926941 bytes_read=2455213 bytes_retransmit=9 bytes_invalid=0 send_seq=348034 receive_seq=348034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015768 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15862 bytes_read=50877 bytes_retransmit=0 bytes_invalid=0 send_seq=2615 receive_seq=2615 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997228 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109428 bytes_read=3487209 bytes_retransmit=9 bytes_invalid=0 send_seq=14815 receive_seq=14815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997642 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51776 bytes_read=1042792 bytes_retransmit=9 bytes_invalid=0 send_seq=6668 receive_seq=6668 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997458 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16075 bytes_read=634331 bytes_retransmit=9 bytes_invalid=0 send_seq=2625 receive_seq=2625 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16615 bytes_read=49909 bytes_retransmit=9 bytes_invalid=0 send_seq=2616 receive_seq=2616 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65187 bytes_read=1106955 bytes_retransmit=0 bytes_invalid=0 send_seq=6713 receive_seq=6713 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998625 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.0 th1: temp=46.4 th2: temp=53.4 th3: temp=51.3 sysload=0.29 cputime=227.299 memavail=7396028 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2498.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19927239 bytes_read=2455638 bytes_retransmit=9 bytes_invalid=0 send_seq=348057 receive_seq=348057 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015773 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15868 bytes_read=50893 bytes_retransmit=0 bytes_invalid=0 send_seq=2616 receive_seq=2616 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997221 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109434 bytes_read=3487323 bytes_retransmit=9 bytes_invalid=0 send_seq=14816 receive_seq=14816 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997633 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51782 bytes_read=1042920 bytes_retransmit=9 bytes_invalid=0 send_seq=6669 receive_seq=6669 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997458 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16081 bytes_read=634595 bytes_retransmit=9 bytes_invalid=0 send_seq=2626 receive_seq=2626 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16621 bytes_read=49925 bytes_retransmit=9 bytes_invalid=0 send_seq=2617 receive_seq=2617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65193 bytes_read=1107311 bytes_retransmit=0 bytes_invalid=0 send_seq=6714 receive_seq=6714 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998631 coil_temp=17.5 refs=0 mcu_temp=20.64 supply_voltage=3.012 th0: temp=45.8 th1: temp=46.5 th2: temp=53.3 th3: temp=51.3 sysload=0.29 cputime=227.342 memavail=7396028 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2499.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19927537 bytes_read=2456092 bytes_retransmit=9 bytes_invalid=0 send_seq=348080 receive_seq=348080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015777 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15874 bytes_read=50909 bytes_retransmit=0 bytes_invalid=0 send_seq=2617 receive_seq=2617 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997205 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109440 bytes_read=3487437 bytes_retransmit=9 bytes_invalid=0 send_seq=14817 receive_seq=14817 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997615 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51788 bytes_read=1043034 bytes_retransmit=9 bytes_invalid=0 send_seq=6670 receive_seq=6670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997452 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16087 bytes_read=634859 bytes_retransmit=9 bytes_invalid=0 send_seq=2627 receive_seq=2627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16627 bytes_read=49941 bytes_retransmit=9 bytes_invalid=0 send_seq=2618 receive_seq=2618 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999444 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65199 bytes_read=1107667 bytes_retransmit=0 bytes_invalid=0 send_seq=6715 receive_seq=6715 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998651 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.0 th1: temp=46.5 th2: temp=53.7 th3: temp=51.5 sysload=0.29 cputime=227.386 memavail=7396028 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2500.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19927835 bytes_read=2456530 bytes_retransmit=9 bytes_invalid=0 send_seq=348103 receive_seq=348103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015780 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=15880 bytes_read=50924 bytes_retransmit=0 bytes_invalid=0 send_seq=2618 receive_seq=2618 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997193 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109446 bytes_read=3487537 bytes_retransmit=9 bytes_invalid=0 send_seq=14818 receive_seq=14818 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997623 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51794 bytes_read=1043134 bytes_retransmit=9 bytes_invalid=0 send_seq=6671 receive_seq=6671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997472 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16093 bytes_read=635108 bytes_retransmit=9 bytes_invalid=0 send_seq=2628 receive_seq=2628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16633 bytes_read=49957 bytes_retransmit=9 bytes_invalid=0 send_seq=2619 receive_seq=2619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65205 bytes_read=1108023 bytes_retransmit=0 bytes_invalid=0 send_seq=6716 receive_seq=6716 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998667 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=45.5 th1: temp=46.4 th2: temp=53.6 th3: temp=51.4 sysload=0.29 cputime=227.428 memavail=7396028 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2501.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19928133 bytes_read=2456953 bytes_retransmit=9 bytes_invalid=0 send_seq=348126 receive_seq=348126 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015785 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15886 bytes_read=50952 bytes_retransmit=0 bytes_invalid=0 send_seq=2619 receive_seq=2619 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997199 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109452 bytes_read=3487665 bytes_retransmit=9 bytes_invalid=0 send_seq=14819 receive_seq=14819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997615 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51800 bytes_read=1043248 bytes_retransmit=9 bytes_invalid=0 send_seq=6672 receive_seq=6672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997467 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16099 bytes_read=635372 bytes_retransmit=9 bytes_invalid=0 send_seq=2629 receive_seq=2629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16639 bytes_read=49984 bytes_retransmit=9 bytes_invalid=0 send_seq=2620 receive_seq=2620 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65211 bytes_read=1108379 bytes_retransmit=0 bytes_invalid=0 send_seq=6717 receive_seq=6717 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998666 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.0 th1: temp=46.4 th2: temp=53.5 th3: temp=51.5 sysload=0.29 cputime=227.472 memavail=7396028 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2502.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19928421 bytes_read=2457397 bytes_retransmit=9 bytes_invalid=0 send_seq=348147 receive_seq=348147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015787 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15892 bytes_read=50967 bytes_retransmit=0 bytes_invalid=0 send_seq=2620 receive_seq=2620 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997201 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109458 bytes_read=3487779 bytes_retransmit=9 bytes_invalid=0 send_seq=14820 receive_seq=14820 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997608 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51806 bytes_read=1043362 bytes_retransmit=9 bytes_invalid=0 send_seq=6673 receive_seq=6673 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997459 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16105 bytes_read=635636 bytes_retransmit=9 bytes_invalid=0 send_seq=2630 receive_seq=2630 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16645 bytes_read=50000 bytes_retransmit=9 bytes_invalid=0 send_seq=2621 receive_seq=2621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999434 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65217 bytes_read=1108735 bytes_retransmit=0 bytes_invalid=0 send_seq=6718 receive_seq=6718 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998651 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=45.9 th1: temp=46.3 th2: temp=53.7 th3: temp=51.4 sysload=0.27 cputime=227.515 memavail=7396028 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2503.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19928725 bytes_read=2457838 bytes_retransmit=9 bytes_invalid=0 send_seq=348171 receive_seq=348171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015788 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15904 bytes_read=50997 bytes_retransmit=0 bytes_invalid=0 send_seq=2622 receive_seq=2622 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997213 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109470 bytes_read=3487895 bytes_retransmit=9 bytes_invalid=0 send_seq=14822 receive_seq=14822 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997611 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51818 bytes_read=1043492 bytes_retransmit=9 bytes_invalid=0 send_seq=6675 receive_seq=6675 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997463 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16117 bytes_read=635886 bytes_retransmit=9 bytes_invalid=0 send_seq=2632 receive_seq=2632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16657 bytes_read=50032 bytes_retransmit=9 bytes_invalid=0 send_seq=2623 receive_seq=2623 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999433 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65229 bytes_read=1109107 bytes_retransmit=0 bytes_invalid=0 send_seq=6720 receive_seq=6720 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998645 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.0 th1: temp=46.3 th2: temp=53.4 th3: temp=51.5 sysload=0.27 cputime=227.559 memavail=7396028 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2504.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19929023 bytes_read=2458263 bytes_retransmit=9 bytes_invalid=0 send_seq=348194 receive_seq=348194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015789 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15910 bytes_read=51013 bytes_retransmit=0 bytes_invalid=0 send_seq=2623 receive_seq=2623 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997241 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109476 bytes_read=3488009 bytes_retransmit=9 bytes_invalid=0 send_seq=14823 receive_seq=14823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63998047 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51824 bytes_read=1043606 bytes_retransmit=9 bytes_invalid=0 send_seq=6676 receive_seq=6676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997493 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16123 bytes_read=636150 bytes_retransmit=9 bytes_invalid=0 send_seq=2633 receive_seq=2633 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997613 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16663 bytes_read=50048 bytes_retransmit=9 bytes_invalid=0 send_seq=2624 receive_seq=2624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999432 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65235 bytes_read=1109463 bytes_retransmit=0 bytes_invalid=0 send_seq=6721 receive_seq=6721 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998623 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.0 th1: temp=46.2 th2: temp=53.4 th3: temp=51.5 sysload=0.27 cputime=227.605 memavail=7396028 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2505.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19929321 bytes_read=2458732 bytes_retransmit=9 bytes_invalid=0 send_seq=348217 receive_seq=348217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015795 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15916 bytes_read=51029 bytes_retransmit=0 bytes_invalid=0 send_seq=2624 receive_seq=2624 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997266 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109482 bytes_read=3488123 bytes_retransmit=9 bytes_invalid=0 send_seq=14824 receive_seq=14824 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997922 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51830 bytes_read=1043720 bytes_retransmit=9 bytes_invalid=0 send_seq=6677 receive_seq=6677 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16129 bytes_read=636429 bytes_retransmit=9 bytes_invalid=0 send_seq=2634 receive_seq=2634 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997614 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16669 bytes_read=50064 bytes_retransmit=9 bytes_invalid=0 send_seq=2625 receive_seq=2625 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999432 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65241 bytes_read=1109837 bytes_retransmit=0 bytes_invalid=0 send_seq=6722 receive_seq=6722 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998647 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=45.9 th1: temp=46.2 th2: temp=53.5 th3: temp=51.2 sysload=0.27 cputime=227.652 memavail=7396028 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2506.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19929619 bytes_read=2459157 bytes_retransmit=9 bytes_invalid=0 send_seq=348240 receive_seq=348240 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015792 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15922 bytes_read=51058 bytes_retransmit=0 bytes_invalid=0 send_seq=2625 receive_seq=2625 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997256 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109488 bytes_read=3488237 bytes_retransmit=9 bytes_invalid=0 send_seq=14825 receive_seq=14825 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997829 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51836 bytes_read=1043820 bytes_retransmit=9 bytes_invalid=0 send_seq=6678 receive_seq=6678 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997493 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16135 bytes_read=636663 bytes_retransmit=9 bytes_invalid=0 send_seq=2635 receive_seq=2635 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16675 bytes_read=50091 bytes_retransmit=9 bytes_invalid=0 send_seq=2626 receive_seq=2626 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999430 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65247 bytes_read=1110193 bytes_retransmit=0 bytes_invalid=0 send_seq=6723 receive_seq=6723 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998636 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=45.9 th1: temp=46.4 th2: temp=53.6 th3: temp=51.5 sysload=0.27 cputime=227.697 memavail=7396056 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2507.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19929917 bytes_read=2459582 bytes_retransmit=9 bytes_invalid=0 send_seq=348263 receive_seq=348263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015800 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15928 bytes_read=51074 bytes_retransmit=0 bytes_invalid=0 send_seq=2626 receive_seq=2626 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997260 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109494 bytes_read=3488365 bytes_retransmit=9 bytes_invalid=0 send_seq=14826 receive_seq=14826 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997782 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51842 bytes_read=1043934 bytes_retransmit=9 bytes_invalid=0 send_seq=6679 receive_seq=6679 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16141 bytes_read=636927 bytes_retransmit=9 bytes_invalid=0 send_seq=2636 receive_seq=2636 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997632 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16681 bytes_read=50107 bytes_retransmit=9 bytes_invalid=0 send_seq=2627 receive_seq=2627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999432 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65253 bytes_read=1110541 bytes_retransmit=0 bytes_invalid=0 send_seq=6724 receive_seq=6724 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998670 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.0 th1: temp=46.6 th2: temp=53.5 th3: temp=51.7 sysload=0.25 cputime=227.741 memavail=7396056 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2508.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19930215 bytes_read=2460036 bytes_retransmit=9 bytes_invalid=0 send_seq=348286 receive_seq=348286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015797 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15934 bytes_read=51090 bytes_retransmit=0 bytes_invalid=0 send_seq=2627 receive_seq=2627 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997271 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109500 bytes_read=3488465 bytes_retransmit=9 bytes_invalid=0 send_seq=14827 receive_seq=14827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997829 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51848 bytes_read=1044048 bytes_retransmit=9 bytes_invalid=0 send_seq=6680 receive_seq=6680 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997604 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16147 bytes_read=637191 bytes_retransmit=9 bytes_invalid=0 send_seq=2637 receive_seq=2637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997616 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16687 bytes_read=50123 bytes_retransmit=9 bytes_invalid=0 send_seq=2628 receive_seq=2628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999429 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65259 bytes_read=1110886 bytes_retransmit=0 bytes_invalid=0 send_seq=6725 receive_seq=6725 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998657 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=45.7 th1: temp=46.3 th2: temp=53.6 th3: temp=51.6 sysload=0.25 cputime=227.786 memavail=7396080 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2509.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19930513 bytes_read=2460461 bytes_retransmit=9 bytes_invalid=0 send_seq=348309 receive_seq=348309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015794 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15940 bytes_read=51106 bytes_retransmit=0 bytes_invalid=0 send_seq=2628 receive_seq=2628 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997291 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109506 bytes_read=3488565 bytes_retransmit=9 bytes_invalid=0 send_seq=14828 receive_seq=14828 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997769 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51854 bytes_read=1044162 bytes_retransmit=9 bytes_invalid=0 send_seq=6681 receive_seq=6681 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997577 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16153 bytes_read=637425 bytes_retransmit=9 bytes_invalid=0 send_seq=2638 receive_seq=2638 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16693 bytes_read=50139 bytes_retransmit=9 bytes_invalid=0 send_seq=2629 receive_seq=2629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65265 bytes_read=1111231 bytes_retransmit=0 bytes_invalid=0 send_seq=6726 receive_seq=6726 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998656 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=45.6 th1: temp=46.1 th2: temp=53.6 th3: temp=51.5 sysload=0.25 cputime=227.828 memavail=7396084 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2510.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=19930811 bytes_read=2460901 bytes_retransmit=9 bytes_invalid=0 send_seq=348332 receive_seq=348332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015797 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15946 bytes_read=51122 bytes_retransmit=0 bytes_invalid=0 send_seq=2629 receive_seq=2629 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997306 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109512 bytes_read=3488693 bytes_retransmit=9 bytes_invalid=0 send_seq=14829 receive_seq=14829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997724 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51860 bytes_read=1044276 bytes_retransmit=9 bytes_invalid=0 send_seq=6682 receive_seq=6682 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997597 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16159 bytes_read=637704 bytes_retransmit=9 bytes_invalid=0 send_seq=2639 receive_seq=2639 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16699 bytes_read=50155 bytes_retransmit=9 bytes_invalid=0 send_seq=2630 receive_seq=2630 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65271 bytes_read=1111576 bytes_retransmit=0 bytes_invalid=0 send_seq=6727 receive_seq=6727 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998643 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.1 th1: temp=46.5 th2: temp=53.6 th3: temp=51.6 sysload=0.25 cputime=227.872 memavail=7396084 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2511.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=19931084 bytes_read=2461325 bytes_retransmit=9 bytes_invalid=0 send_seq=348350 receive_seq=348350 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015822 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15952 bytes_read=51151 bytes_retransmit=0 bytes_invalid=0 send_seq=2630 receive_seq=2630 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997283 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109518 bytes_read=3488793 bytes_retransmit=9 bytes_invalid=0 send_seq=14830 receive_seq=14830 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997678 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51866 bytes_read=1044390 bytes_retransmit=9 bytes_invalid=0 send_seq=6683 receive_seq=6683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997573 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16165 bytes_read=637968 bytes_retransmit=9 bytes_invalid=0 send_seq=2640 receive_seq=2640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16705 bytes_read=50182 bytes_retransmit=9 bytes_invalid=0 send_seq=2631 receive_seq=2631 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65277 bytes_read=1111921 bytes_retransmit=0 bytes_invalid=0 send_seq=6728 receive_seq=6728 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998635 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.1 th1: temp=46.3 th2: temp=53.6 th3: temp=51.6 sysload=0.25 cputime=227.919 memavail=7397220 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2512.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=19931382 bytes_read=2461750 bytes_retransmit=9 bytes_invalid=0 send_seq=348373 receive_seq=348373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015820 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15958 bytes_read=51167 bytes_retransmit=0 bytes_invalid=0 send_seq=2631 receive_seq=2631 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997225 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109524 bytes_read=3488907 bytes_retransmit=9 bytes_invalid=0 send_seq=14831 receive_seq=14831 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997597 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51872 bytes_read=1044490 bytes_retransmit=9 bytes_invalid=0 send_seq=6684 receive_seq=6684 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997489 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16171 bytes_read=638202 bytes_retransmit=9 bytes_invalid=0 send_seq=2641 receive_seq=2641 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997601 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16711 bytes_read=50198 bytes_retransmit=9 bytes_invalid=0 send_seq=2632 receive_seq=2632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999427 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65283 bytes_read=1112266 bytes_retransmit=0 bytes_invalid=0 send_seq=6729 receive_seq=6729 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998606 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.0 th1: temp=46.4 th2: temp=53.6 th3: temp=51.5 sysload=0.23 cputime=227.963 memavail=7396996 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2513.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=19931680 bytes_read=2462175 bytes_retransmit=9 bytes_invalid=0 send_seq=348396 receive_seq=348396 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015814 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15964 bytes_read=51183 bytes_retransmit=0 bytes_invalid=0 send_seq=2632 receive_seq=2632 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997239 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109530 bytes_read=3489035 bytes_retransmit=9 bytes_invalid=0 send_seq=14832 receive_seq=14832 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997595 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51878 bytes_read=1044604 bytes_retransmit=9 bytes_invalid=0 send_seq=6685 receive_seq=6685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997485 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16177 bytes_read=638481 bytes_retransmit=9 bytes_invalid=0 send_seq=2642 receive_seq=2642 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16717 bytes_read=50214 bytes_retransmit=9 bytes_invalid=0 send_seq=2633 receive_seq=2633 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999432 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65289 bytes_read=1112611 bytes_retransmit=0 bytes_invalid=0 send_seq=6730 receive_seq=6730 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998612 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=45.5 th1: temp=46.3 th2: temp=53.7 th3: temp=51.6 sysload=0.23 cputime=228.006 memavail=7396996 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2514.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=19931978 bytes_read=2462629 bytes_retransmit=9 bytes_invalid=0 send_seq=348419 receive_seq=348419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015832 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15970 bytes_read=51199 bytes_retransmit=0 bytes_invalid=0 send_seq=2633 receive_seq=2633 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997251 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109536 bytes_read=3489135 bytes_retransmit=9 bytes_invalid=0 send_seq=14833 receive_seq=14833 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997626 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51884 bytes_read=1044732 bytes_retransmit=9 bytes_invalid=0 send_seq=6686 receive_seq=6686 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997513 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16183 bytes_read=638730 bytes_retransmit=9 bytes_invalid=0 send_seq=2643 receive_seq=2643 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16723 bytes_read=50230 bytes_retransmit=9 bytes_invalid=0 send_seq=2634 receive_seq=2634 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65295 bytes_read=1112956 bytes_retransmit=0 bytes_invalid=0 send_seq=6731 receive_seq=6731 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998622 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=45.9 th1: temp=46.4 th2: temp=53.7 th3: temp=51.7 sysload=0.23 cputime=228.048 memavail=7396996 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2515.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19932276 bytes_read=2463069 bytes_retransmit=9 bytes_invalid=0 send_seq=348442 receive_seq=348442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015831 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15976 bytes_read=51215 bytes_retransmit=0 bytes_invalid=0 send_seq=2634 receive_seq=2634 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997218 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109542 bytes_read=3489235 bytes_retransmit=9 bytes_invalid=0 send_seq=14834 receive_seq=14834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997586 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51890 bytes_read=1044832 bytes_retransmit=9 bytes_invalid=0 send_seq=6687 receive_seq=6687 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997535 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16189 bytes_read=638979 bytes_retransmit=9 bytes_invalid=0 send_seq=2644 receive_seq=2644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16729 bytes_read=50246 bytes_retransmit=9 bytes_invalid=0 send_seq=2635 receive_seq=2635 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65301 bytes_read=1113305 bytes_retransmit=0 bytes_invalid=0 send_seq=6732 receive_seq=6732 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998603 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.1 th1: temp=46.2 th2: temp=53.5 th3: temp=51.7 sysload=0.23 cputime=228.091 memavail=7396504 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2516.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19932574 bytes_read=2463494 bytes_retransmit=9 bytes_invalid=0 send_seq=348465 receive_seq=348465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015829 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15982 bytes_read=51244 bytes_retransmit=0 bytes_invalid=0 send_seq=2635 receive_seq=2635 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997230 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109548 bytes_read=3489363 bytes_retransmit=9 bytes_invalid=0 send_seq=14835 receive_seq=14835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997585 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51896 bytes_read=1044946 bytes_retransmit=9 bytes_invalid=0 send_seq=6688 receive_seq=6688 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997518 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16195 bytes_read=639258 bytes_retransmit=9 bytes_invalid=0 send_seq=2645 receive_seq=2645 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16735 bytes_read=50273 bytes_retransmit=9 bytes_invalid=0 send_seq=2636 receive_seq=2636 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999429 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65307 bytes_read=1113661 bytes_retransmit=0 bytes_invalid=0 send_seq=6733 receive_seq=6733 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998610 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=45.4 th1: temp=46.3 th2: temp=53.9 th3: temp=51.7 sysload=0.23 cputime=228.134 memavail=7396504 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2517.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19932872 bytes_read=2463948 bytes_retransmit=9 bytes_invalid=0 send_seq=348488 receive_seq=348488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015824 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15988 bytes_read=51260 bytes_retransmit=0 bytes_invalid=0 send_seq=2636 receive_seq=2636 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997237 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109554 bytes_read=3489477 bytes_retransmit=9 bytes_invalid=0 send_seq=14836 receive_seq=14836 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997590 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51902 bytes_read=1045060 bytes_retransmit=9 bytes_invalid=0 send_seq=6689 receive_seq=6689 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16201 bytes_read=639507 bytes_retransmit=9 bytes_invalid=0 send_seq=2646 receive_seq=2646 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16741 bytes_read=50289 bytes_retransmit=9 bytes_invalid=0 send_seq=2637 receive_seq=2637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999431 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65313 bytes_read=1114017 bytes_retransmit=0 bytes_invalid=0 send_seq=6734 receive_seq=6734 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998614 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=45.7 th1: temp=46.4 th2: temp=53.5 th3: temp=51.7 sysload=0.21 cputime=228.177 memavail=7396512 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2518.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19933170 bytes_read=2464373 bytes_retransmit=9 bytes_invalid=0 send_seq=348511 receive_seq=348511 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015819 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=15994 bytes_read=51276 bytes_retransmit=0 bytes_invalid=0 send_seq=2637 receive_seq=2637 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997251 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109560 bytes_read=3489577 bytes_retransmit=9 bytes_invalid=0 send_seq=14837 receive_seq=14837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997600 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=51908 bytes_read=1045160 bytes_retransmit=9 bytes_invalid=0 send_seq=6690 receive_seq=6690 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997507 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16207 bytes_read=639741 bytes_retransmit=9 bytes_invalid=0 send_seq=2647 receive_seq=2647 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16747 bytes_read=50305 bytes_retransmit=9 bytes_invalid=0 send_seq=2638 receive_seq=2638 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65319 bytes_read=1114373 bytes_retransmit=0 bytes_invalid=0 send_seq=6735 receive_seq=6735 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998631 coil_temp=17.5 refs=0 mcu_temp=20.64 supply_voltage=3.012 th0: temp=46.0 th1: temp=46.1 th2: temp=53.6 th3: temp=51.9 sysload=0.21 cputime=228.221 memavail=7396512 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2519.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19933463 bytes_read=2464793 bytes_retransmit=9 bytes_invalid=0 send_seq=348533 receive_seq=348533 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015814 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=16000 bytes_read=51292 bytes_retransmit=0 bytes_invalid=0 send_seq=2638 receive_seq=2638 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997264 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109566 bytes_read=3489705 bytes_retransmit=9 bytes_invalid=0 send_seq=14838 receive_seq=14838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997633 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=51914 bytes_read=1045288 bytes_retransmit=9 bytes_invalid=0 send_seq=6691 receive_seq=6691 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16213 bytes_read=640020 bytes_retransmit=9 bytes_invalid=0 send_seq=2648 receive_seq=2648 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16753 bytes_read=50321 bytes_retransmit=9 bytes_invalid=0 send_seq=2639 receive_seq=2639 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65325 bytes_read=1114729 bytes_retransmit=0 bytes_invalid=0 send_seq=6736 receive_seq=6736 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998641 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.0 th1: temp=46.5 th2: temp=53.7 th3: temp=51.3 sysload=0.21 cputime=228.264 memavail=7396512 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2520.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=19933761 bytes_read=2465262 bytes_retransmit=9 bytes_invalid=0 send_seq=348556 receive_seq=348556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015818 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=16006 bytes_read=51308 bytes_retransmit=0 bytes_invalid=0 send_seq=2639 receive_seq=2639 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997271 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109572 bytes_read=3489805 bytes_retransmit=9 bytes_invalid=0 send_seq=14839 receive_seq=14839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997771 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=51920 bytes_read=1045402 bytes_retransmit=9 bytes_invalid=0 send_seq=6692 receive_seq=6692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997514 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16219 bytes_read=640284 bytes_retransmit=9 bytes_invalid=0 send_seq=2649 receive_seq=2649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16759 bytes_read=50337 bytes_retransmit=9 bytes_invalid=0 send_seq=2640 receive_seq=2640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65331 bytes_read=1115085 bytes_retransmit=0 bytes_invalid=0 send_seq=6737 receive_seq=6737 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998664 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.1 th1: temp=46.6 th2: temp=53.6 th3: temp=51.7 sysload=0.21 cputime=228.307 memavail=7396512 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2521.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=19934059 bytes_read=2465687 bytes_retransmit=9 bytes_invalid=0 send_seq=348579 receive_seq=348579 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015820 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=16012 bytes_read=51337 bytes_retransmit=0 bytes_invalid=0 send_seq=2640 receive_seq=2640 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997289 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109578 bytes_read=3489905 bytes_retransmit=9 bytes_invalid=0 send_seq=14840 receive_seq=14840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997707 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=51926 bytes_read=1045502 bytes_retransmit=9 bytes_invalid=0 send_seq=6693 receive_seq=6693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997491 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16225 bytes_read=640518 bytes_retransmit=9 bytes_invalid=0 send_seq=2650 receive_seq=2650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16765 bytes_read=50364 bytes_retransmit=9 bytes_invalid=0 send_seq=2641 receive_seq=2641 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65337 bytes_read=1115441 bytes_retransmit=0 bytes_invalid=0 send_seq=6738 receive_seq=6738 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998646 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=45.8 th1: temp=46.4 th2: temp=53.7 th3: temp=51.8 sysload=0.21 cputime=228.349 memavail=7396512 print_time=2484.489 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Extruder extruder already active
Extruder 'extruder' now syncing with 'extruder'
Extruder 'extruder1' now syncing with 'extruder'
RatOS | SET_PRESSURE_ADVANCE:: T0
extruder: pressure_advance: 0.008000
pressure_advance_smooth_time: 0.040000
RatOS | SET_PRESSURE_ADVANCE:: T1
extruder1: pressure_advance: 0.008000
pressure_advance_smooth_time: 0.040000
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 2556.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19947834 bytes_read=2481207 bytes_retransmit=9 bytes_invalid=0 send_seq=349427 receive_seq=349427 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015900 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16222 bytes_read=51988 bytes_retransmit=0 bytes_invalid=0 send_seq=2675 receive_seq=2675 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999233 adj=49997219 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109788 bytes_read=3493806 bytes_retransmit=9 bytes_invalid=0 send_seq=14875 receive_seq=14875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997550 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52136 bytes_read=1049403 bytes_retransmit=9 bytes_invalid=0 send_seq=6728 receive_seq=6728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16435 bytes_read=649533 bytes_retransmit=9 bytes_invalid=0 send_seq=2685 receive_seq=2685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16975 bytes_read=50993 bytes_retransmit=9 bytes_invalid=0 send_seq=2676 receive_seq=2676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65547 bytes_read=1127885 bytes_retransmit=0 bytes_invalid=0 send_seq=6773 receive_seq=6773 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998685 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.2 th1: temp=46.4 th2: temp=54.1 th3: temp=52.1 sysload=0.17 cputime=229.971 memavail=7397636 print_time=2580.508 buffer_time=1.403 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2557.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19948117 bytes_read=2481617 bytes_retransmit=9 bytes_invalid=0 send_seq=349447 receive_seq=349447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015901 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16228 bytes_read=52004 bytes_retransmit=0 bytes_invalid=0 send_seq=2676 receive_seq=2676 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999233 adj=49997232 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=109794 bytes_read=3493920 bytes_retransmit=9 bytes_invalid=0 send_seq=14876 receive_seq=14876 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997698 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52142 bytes_read=1049503 bytes_retransmit=9 bytes_invalid=0 send_seq=6729 receive_seq=6729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997483 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16441 bytes_read=649767 bytes_retransmit=9 bytes_invalid=0 send_seq=2686 receive_seq=2686 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16981 bytes_read=51008 bytes_retransmit=9 bytes_invalid=0 send_seq=2677 receive_seq=2677 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65553 bytes_read=1128241 bytes_retransmit=0 bytes_invalid=0 send_seq=6774 receive_seq=6774 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998658 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.0 th1: temp=46.4 th2: temp=54.1 th3: temp=52.1 sysload=0.15 cputime=230.015 memavail=7397636 print_time=2580.508 buffer_time=0.402 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2558.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19948410 bytes_read=2482037 bytes_retransmit=9 bytes_invalid=0 send_seq=349469 receive_seq=349469 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015902 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16234 bytes_read=52020 bytes_retransmit=0 bytes_invalid=0 send_seq=2677 receive_seq=2677 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999233 adj=49997235 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=109800 bytes_read=3494048 bytes_retransmit=9 bytes_invalid=0 send_seq=14877 receive_seq=14877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997701 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52148 bytes_read=1049631 bytes_retransmit=9 bytes_invalid=0 send_seq=6730 receive_seq=6730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997478 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16447 bytes_read=650061 bytes_retransmit=9 bytes_invalid=0 send_seq=2687 receive_seq=2687 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16987 bytes_read=51023 bytes_retransmit=9 bytes_invalid=0 send_seq=2678 receive_seq=2678 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65559 bytes_read=1128597 bytes_retransmit=0 bytes_invalid=0 send_seq=6775 receive_seq=6775 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998680 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.2 th1: temp=46.5 th2: temp=54.1 th3: temp=52.1 sysload=0.15 cputime=230.061 memavail=7397636 print_time=2580.508 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2559.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19948698 bytes_read=2482481 bytes_retransmit=9 bytes_invalid=0 send_seq=349490 receive_seq=349490 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015902 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16240 bytes_read=52036 bytes_retransmit=0 bytes_invalid=0 send_seq=2678 receive_seq=2678 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997240 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=109806 bytes_read=3494148 bytes_retransmit=9 bytes_invalid=0 send_seq=14878 receive_seq=14878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997678 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52154 bytes_read=1049745 bytes_retransmit=9 bytes_invalid=0 send_seq=6731 receive_seq=6731 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997469 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16453 bytes_read=650295 bytes_retransmit=9 bytes_invalid=0 send_seq=2688 receive_seq=2688 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16993 bytes_read=51038 bytes_retransmit=9 bytes_invalid=0 send_seq=2679 receive_seq=2679 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999439 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65565 bytes_read=1128953 bytes_retransmit=0 bytes_invalid=0 send_seq=6776 receive_seq=6776 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998660 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.3 th1: temp=46.5 th2: temp=54.0 th3: temp=52.2 sysload=0.15 cputime=230.104 memavail=7397636 print_time=2580.508 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2560.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19948996 bytes_read=2482921 bytes_retransmit=9 bytes_invalid=0 send_seq=349513 receive_seq=349513 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015919 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16246 bytes_read=52052 bytes_retransmit=0 bytes_invalid=0 send_seq=2679 receive_seq=2679 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997245 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=109812 bytes_read=3494248 bytes_retransmit=9 bytes_invalid=0 send_seq=14879 receive_seq=14879 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997665 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52160 bytes_read=1049845 bytes_retransmit=9 bytes_invalid=0 send_seq=6732 receive_seq=6732 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997467 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16459 bytes_read=650544 bytes_retransmit=9 bytes_invalid=0 send_seq=2689 receive_seq=2689 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997634 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=16999 bytes_read=51053 bytes_retransmit=9 bytes_invalid=0 send_seq=2680 receive_seq=2680 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65571 bytes_read=1129309 bytes_retransmit=0 bytes_invalid=0 send_seq=6777 receive_seq=6777 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998646 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=45.5 th1: temp=46.9 th2: temp=54.1 th3: temp=52.1 sysload=0.15 cputime=230.149 memavail=7397636 print_time=2580.508 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2561.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19949294 bytes_read=2483346 bytes_retransmit=9 bytes_invalid=0 send_seq=349536 receive_seq=349536 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015916 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16252 bytes_read=52081 bytes_retransmit=0 bytes_invalid=0 send_seq=2680 receive_seq=2680 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997237 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=109818 bytes_read=3494376 bytes_retransmit=9 bytes_invalid=0 send_seq=14880 receive_seq=14880 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997589 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52166 bytes_read=1049973 bytes_retransmit=9 bytes_invalid=0 send_seq=6733 receive_seq=6733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997425 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16465 bytes_read=650838 bytes_retransmit=9 bytes_invalid=0 send_seq=2690 receive_seq=2690 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997603 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17005 bytes_read=51079 bytes_retransmit=9 bytes_invalid=0 send_seq=2681 receive_seq=2681 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999427 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65577 bytes_read=1129665 bytes_retransmit=0 bytes_invalid=0 send_seq=6778 receive_seq=6778 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998612 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.4 th1: temp=47.3 th2: temp=54.0 th3: temp=52.1 sysload=0.15 cputime=230.195 memavail=7397636 print_time=2580.508 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2562.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19949592 bytes_read=2483800 bytes_retransmit=9 bytes_invalid=0 send_seq=349559 receive_seq=349559 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015911 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16258 bytes_read=52097 bytes_retransmit=0 bytes_invalid=0 send_seq=2681 receive_seq=2681 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997241 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109824 bytes_read=3494490 bytes_retransmit=9 bytes_invalid=0 send_seq=14881 receive_seq=14881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997579 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52172 bytes_read=1050073 bytes_retransmit=9 bytes_invalid=0 send_seq=6734 receive_seq=6734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997443 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16471 bytes_read=651072 bytes_retransmit=9 bytes_invalid=0 send_seq=2691 receive_seq=2691 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997614 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17011 bytes_read=51094 bytes_retransmit=9 bytes_invalid=0 send_seq=2682 receive_seq=2682 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999429 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65583 bytes_read=1130021 bytes_retransmit=0 bytes_invalid=0 send_seq=6779 receive_seq=6779 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998611 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.4 th1: temp=47.4 th2: temp=54.1 th3: temp=52.3 sysload=0.14 cputime=230.246 memavail=7391588 print_time=2580.508 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2563.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19949880 bytes_read=2484215 bytes_retransmit=9 bytes_invalid=0 send_seq=349580 receive_seq=349580 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015913 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16264 bytes_read=52113 bytes_retransmit=0 bytes_invalid=0 send_seq=2682 receive_seq=2682 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997538 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109830 bytes_read=3494590 bytes_retransmit=9 bytes_invalid=0 send_seq=14882 receive_seq=14882 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997617 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52178 bytes_read=1050173 bytes_retransmit=9 bytes_invalid=0 send_seq=6735 receive_seq=6735 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997466 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16477 bytes_read=651306 bytes_retransmit=9 bytes_invalid=0 send_seq=2692 receive_seq=2692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17017 bytes_read=51109 bytes_retransmit=9 bytes_invalid=0 send_seq=2683 receive_seq=2683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999432 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65589 bytes_read=1130377 bytes_retransmit=0 bytes_invalid=0 send_seq=6780 receive_seq=6780 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998616 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.3 th1: temp=47.4 th2: temp=54.3 th3: temp=52.3 sysload=0.14 cputime=230.290 memavail=7397256 print_time=2580.508 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2564.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19950179 bytes_read=2484651 bytes_retransmit=9 bytes_invalid=0 send_seq=349603 receive_seq=349603 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015935 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16276 bytes_read=52145 bytes_retransmit=0 bytes_invalid=0 send_seq=2684 receive_seq=2684 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997455 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109842 bytes_read=3494734 bytes_retransmit=9 bytes_invalid=0 send_seq=14884 receive_seq=14884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997684 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52190 bytes_read=1050331 bytes_retransmit=9 bytes_invalid=0 send_seq=6737 receive_seq=6737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997462 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16489 bytes_read=651616 bytes_retransmit=9 bytes_invalid=0 send_seq=2694 receive_seq=2694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17029 bytes_read=51139 bytes_retransmit=9 bytes_invalid=0 send_seq=2685 receive_seq=2685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999458 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65601 bytes_read=1130749 bytes_retransmit=0 bytes_invalid=0 send_seq=6782 receive_seq=6782 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998740 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.5 th1: temp=47.5 th2: temp=54.0 th3: temp=52.2 sysload=0.14 cputime=230.336 memavail=7397260 print_time=2580.508 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2565.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19950477 bytes_read=2485115 bytes_retransmit=9 bytes_invalid=0 send_seq=349626 receive_seq=349626 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015931 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16282 bytes_read=52161 bytes_retransmit=0 bytes_invalid=0 send_seq=2685 receive_seq=2685 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997343 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109848 bytes_read=3494834 bytes_retransmit=9 bytes_invalid=0 send_seq=14885 receive_seq=14885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997707 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52196 bytes_read=1050431 bytes_retransmit=9 bytes_invalid=0 send_seq=6738 receive_seq=6738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997415 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16495 bytes_read=651865 bytes_retransmit=9 bytes_invalid=0 send_seq=2695 receive_seq=2695 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17035 bytes_read=51154 bytes_retransmit=9 bytes_invalid=0 send_seq=2686 receive_seq=2686 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65607 bytes_read=1131105 bytes_retransmit=0 bytes_invalid=0 send_seq=6783 receive_seq=6783 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998657 coil_temp=17.4 refs=0 mcu_temp=20.64 supply_voltage=3.012 th0: temp=46.6 th1: temp=48.0 th2: temp=54.1 th3: temp=52.2 sysload=0.14 cputime=230.381 memavail=7397140 print_time=2580.508 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2566.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19951281 bytes_read=2485585 bytes_retransmit=9 bytes_invalid=0 send_seq=349658 receive_seq=349658 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015922 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=16288 bytes_read=52190 bytes_retransmit=0 bytes_invalid=0 send_seq=2686 receive_seq=2686 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997297 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109854 bytes_read=3494934 bytes_retransmit=9 bytes_invalid=0 send_seq=14886 receive_seq=14886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997665 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52202 bytes_read=1050531 bytes_retransmit=9 bytes_invalid=0 send_seq=6739 receive_seq=6739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997439 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16501 bytes_read=652099 bytes_retransmit=9 bytes_invalid=0 send_seq=2696 receive_seq=2696 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17041 bytes_read=51180 bytes_retransmit=9 bytes_invalid=0 send_seq=2687 receive_seq=2687 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65613 bytes_read=1131461 bytes_retransmit=0 bytes_invalid=0 send_seq=6784 receive_seq=6784 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998650 coil_temp=17.4 refs=0 mcu_temp=20.64 supply_voltage=3.012 th0: temp=46.3 th1: temp=47.7 th2: temp=54.1 th3: temp=52.2 sysload=0.14 cputime=230.430 memavail=7397140 print_time=2588.991 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2567.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19951579 bytes_read=2486010 bytes_retransmit=9 bytes_invalid=0 send_seq=349681 receive_seq=349681 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015929 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=16294 bytes_read=52206 bytes_retransmit=0 bytes_invalid=0 send_seq=2687 receive_seq=2687 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997282 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109860 bytes_read=3495076 bytes_retransmit=9 bytes_invalid=0 send_seq=14887 receive_seq=14887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997655 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52208 bytes_read=1050659 bytes_retransmit=9 bytes_invalid=0 send_seq=6740 receive_seq=6740 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997474 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16507 bytes_read=652393 bytes_retransmit=9 bytes_invalid=0 send_seq=2697 receive_seq=2697 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17047 bytes_read=51195 bytes_retransmit=9 bytes_invalid=0 send_seq=2688 receive_seq=2688 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65619 bytes_read=1131817 bytes_retransmit=0 bytes_invalid=0 send_seq=6785 receive_seq=6785 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998649 coil_temp=17.4 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.5 th1: temp=48.2 th2: temp=54.4 th3: temp=52.2 sysload=0.13 cputime=230.475 memavail=7397140 print_time=2588.991 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2568.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19951877 bytes_read=2486464 bytes_retransmit=9 bytes_invalid=0 send_seq=349704 receive_seq=349704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015922 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=16300 bytes_read=52222 bytes_retransmit=0 bytes_invalid=0 send_seq=2688 receive_seq=2688 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997236 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109866 bytes_read=3495176 bytes_retransmit=9 bytes_invalid=0 send_seq=14888 receive_seq=14888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997597 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52214 bytes_read=1050759 bytes_retransmit=9 bytes_invalid=0 send_seq=6741 receive_seq=6741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997468 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16513 bytes_read=652627 bytes_retransmit=9 bytes_invalid=0 send_seq=2698 receive_seq=2698 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17053 bytes_read=51210 bytes_retransmit=9 bytes_invalid=0 send_seq=2689 receive_seq=2689 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65625 bytes_read=1132173 bytes_retransmit=0 bytes_invalid=0 send_seq=6786 receive_seq=6786 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998634 coil_temp=17.4 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.7 th1: temp=48.3 th2: temp=54.4 th3: temp=52.1 sysload=0.13 cputime=230.520 memavail=7397140 print_time=2588.991 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2569.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19952170 bytes_read=2486884 bytes_retransmit=9 bytes_invalid=0 send_seq=349726 receive_seq=349726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015927 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=16306 bytes_read=52238 bytes_retransmit=0 bytes_invalid=0 send_seq=2689 receive_seq=2689 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997241 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109872 bytes_read=3495276 bytes_retransmit=9 bytes_invalid=0 send_seq=14889 receive_seq=14889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997598 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52220 bytes_read=1050873 bytes_retransmit=9 bytes_invalid=0 send_seq=6742 receive_seq=6742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16519 bytes_read=652861 bytes_retransmit=9 bytes_invalid=0 send_seq=2699 receive_seq=2699 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17059 bytes_read=51225 bytes_retransmit=9 bytes_invalid=0 send_seq=2690 receive_seq=2690 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65631 bytes_read=1132529 bytes_retransmit=0 bytes_invalid=0 send_seq=6787 receive_seq=6787 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998641 coil_temp=17.4 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.2 th1: temp=48.2 th2: temp=54.2 th3: temp=52.0 sysload=0.13 cputime=230.564 memavail=7397140 print_time=2588.991 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2570.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19952468 bytes_read=2487324 bytes_retransmit=9 bytes_invalid=0 send_seq=349749 receive_seq=349749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015925 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=16312 bytes_read=52254 bytes_retransmit=0 bytes_invalid=0 send_seq=2690 receive_seq=2690 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997222 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109878 bytes_read=3495404 bytes_retransmit=9 bytes_invalid=0 send_seq=14890 receive_seq=14890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997581 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52226 bytes_read=1051001 bytes_retransmit=9 bytes_invalid=0 send_seq=6743 receive_seq=6743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997489 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16525 bytes_read=653166 bytes_retransmit=9 bytes_invalid=0 send_seq=2700 receive_seq=2700 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997634 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17065 bytes_read=51240 bytes_retransmit=9 bytes_invalid=0 send_seq=2691 receive_seq=2691 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999433 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65637 bytes_read=1132885 bytes_retransmit=0 bytes_invalid=0 send_seq=6788 receive_seq=6788 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998623 coil_temp=17.4 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=46.5 th1: temp=48.5 th2: temp=54.0 th3: temp=52.2 sysload=0.13 cputime=230.607 memavail=7397140 print_time=2588.991 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2571.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19952766 bytes_read=2487778 bytes_retransmit=9 bytes_invalid=0 send_seq=349772 receive_seq=349772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015923 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=16318 bytes_read=52283 bytes_retransmit=0 bytes_invalid=0 send_seq=2691 receive_seq=2691 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997225 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109884 bytes_read=3495504 bytes_retransmit=9 bytes_invalid=0 send_seq=14891 receive_seq=14891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997577 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52232 bytes_read=1051101 bytes_retransmit=9 bytes_invalid=0 send_seq=6744 receive_seq=6744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16531 bytes_read=653384 bytes_retransmit=9 bytes_invalid=0 send_seq=2701 receive_seq=2701 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17071 bytes_read=51267 bytes_retransmit=9 bytes_invalid=0 send_seq=2692 receive_seq=2692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999433 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65643 bytes_read=1133241 bytes_retransmit=0 bytes_invalid=0 send_seq=6789 receive_seq=6789 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998618 coil_temp=17.4 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=46.4 th1: temp=48.6 th2: temp=54.0 th3: temp=52.3 sysload=0.13 cputime=230.650 memavail=7397140 print_time=2588.991 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2572.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19952833 bytes_read=2487886 bytes_retransmit=9 bytes_invalid=0 send_seq=349774 receive_seq=349774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015925 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=16324 bytes_read=52299 bytes_retransmit=0 bytes_invalid=0 send_seq=2692 receive_seq=2692 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997233 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109890 bytes_read=3495618 bytes_retransmit=9 bytes_invalid=0 send_seq=14892 receive_seq=14892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997575 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52238 bytes_read=1051201 bytes_retransmit=9 bytes_invalid=0 send_seq=6745 receive_seq=6745 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16537 bytes_read=653602 bytes_retransmit=9 bytes_invalid=0 send_seq=2702 receive_seq=2702 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17077 bytes_read=51283 bytes_retransmit=9 bytes_invalid=0 send_seq=2693 receive_seq=2693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999436 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65649 bytes_read=1133597 bytes_retransmit=0 bytes_invalid=0 send_seq=6790 receive_seq=6790 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998619 coil_temp=17.4 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=46.9 th1: temp=48.3 th2: temp=54.5 th3: temp=52.1 sysload=0.12 cputime=230.684 memavail=7397140 print_time=2595.199 buffer_time=0.088 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2573.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19952839 bytes_read=2487989 bytes_retransmit=9 bytes_invalid=0 send_seq=349775 receive_seq=349775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015924 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=16330 bytes_read=52315 bytes_retransmit=0 bytes_invalid=0 send_seq=2693 receive_seq=2693 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997238 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109896 bytes_read=3495746 bytes_retransmit=9 bytes_invalid=0 send_seq=14893 receive_seq=14893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997568 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52244 bytes_read=1051329 bytes_retransmit=9 bytes_invalid=0 send_seq=6746 receive_seq=6746 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997485 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16543 bytes_read=653876 bytes_retransmit=9 bytes_invalid=0 send_seq=2703 receive_seq=2703 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17083 bytes_read=51299 bytes_retransmit=9 bytes_invalid=0 send_seq=2694 receive_seq=2694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999436 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65655 bytes_read=1133953 bytes_retransmit=0 bytes_invalid=0 send_seq=6791 receive_seq=6791 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998624 coil_temp=17.4 refs=0 mcu_temp=20.66 supply_voltage=3.012 th0: temp=46.2 th1: temp=48.6 th2: temp=54.0 th3: temp=52.0 sysload=0.12 cputime=230.717 memavail=7397184 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2574.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=19952845 bytes_read=2488121 bytes_retransmit=9 bytes_invalid=0 send_seq=349776 receive_seq=349776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015923 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=16336 bytes_read=52331 bytes_retransmit=0 bytes_invalid=0 send_seq=2694 receive_seq=2694 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997286 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109902 bytes_read=3495846 bytes_retransmit=9 bytes_invalid=0 send_seq=14894 receive_seq=14894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997587 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52250 bytes_read=1051443 bytes_retransmit=9 bytes_invalid=0 send_seq=6747 receive_seq=6747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16549 bytes_read=654094 bytes_retransmit=9 bytes_invalid=0 send_seq=2704 receive_seq=2704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17089 bytes_read=51315 bytes_retransmit=9 bytes_invalid=0 send_seq=2695 receive_seq=2695 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65661 bytes_read=1134309 bytes_retransmit=0 bytes_invalid=0 send_seq=6792 receive_seq=6792 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998617 coil_temp=17.4 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.2 th1: temp=48.6 th2: temp=53.8 th3: temp=52.0 sysload=0.12 cputime=230.748 memavail=7397184 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2575.6: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000003 mcu_task_stddev=0.000005 bytes_write=19952851 bytes_read=2488239 bytes_retransmit=9 bytes_invalid=0 send_seq=349777 receive_seq=349777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015921 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=16342 bytes_read=52347 bytes_retransmit=0 bytes_invalid=0 send_seq=2695 receive_seq=2695 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997282 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109908 bytes_read=3495946 bytes_retransmit=9 bytes_invalid=0 send_seq=14895 receive_seq=14895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997591 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52256 bytes_read=1051543 bytes_retransmit=9 bytes_invalid=0 send_seq=6748 receive_seq=6748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=16555 bytes_read=654327 bytes_retransmit=9 bytes_invalid=0 send_seq=2705 receive_seq=2705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17095 bytes_read=51331 bytes_retransmit=9 bytes_invalid=0 send_seq=2696 receive_seq=2696 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65667 bytes_read=1134665 bytes_retransmit=0 bytes_invalid=0 send_seq=6793 receive_seq=6793 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998622 coil_temp=17.4 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.1 th1: temp=48.3 th2: temp=53.6 th3: temp=51.8 sysload=0.12 cputime=230.778 memavail=7396680 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2576.6: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000003 mcu_task_stddev=0.000005 bytes_write=19952857 bytes_read=2488337 bytes_retransmit=9 bytes_invalid=0 send_seq=349778 receive_seq=349778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015918 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=16348 bytes_read=52376 bytes_retransmit=0 bytes_invalid=0 send_seq=2696 receive_seq=2696 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997262 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109914 bytes_read=3496074 bytes_retransmit=9 bytes_invalid=0 send_seq=14896 receive_seq=14896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997694 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52262 bytes_read=1051671 bytes_retransmit=9 bytes_invalid=0 send_seq=6749 receive_seq=6749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997512 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=16561 bytes_read=654610 bytes_retransmit=9 bytes_invalid=0 send_seq=2706 receive_seq=2706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17101 bytes_read=51358 bytes_retransmit=9 bytes_invalid=0 send_seq=2697 receive_seq=2697 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65673 bytes_read=1135021 bytes_retransmit=0 bytes_invalid=0 send_seq=6794 receive_seq=6794 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998624 coil_temp=17.4 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.1 th1: temp=48.2 th2: temp=53.3 th3: temp=51.5 sysload=0.12 cputime=230.811 memavail=7396684 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2577.6: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000003 mcu_task_stddev=0.000005 bytes_write=19952863 bytes_read=2488469 bytes_retransmit=9 bytes_invalid=0 send_seq=349779 receive_seq=349779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015917 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=16354 bytes_read=52392 bytes_retransmit=0 bytes_invalid=0 send_seq=2697 receive_seq=2697 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997259 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109920 bytes_read=3496188 bytes_retransmit=9 bytes_invalid=0 send_seq=14897 receive_seq=14897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997686 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52268 bytes_read=1051771 bytes_retransmit=9 bytes_invalid=0 send_seq=6750 receive_seq=6750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997514 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=16567 bytes_read=654844 bytes_retransmit=9 bytes_invalid=0 send_seq=2707 receive_seq=2707 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17107 bytes_read=51374 bytes_retransmit=9 bytes_invalid=0 send_seq=2698 receive_seq=2698 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65679 bytes_read=1135377 bytes_retransmit=0 bytes_invalid=0 send_seq=6795 receive_seq=6795 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998631 coil_temp=17.4 refs=0 mcu_temp=20.64 supply_voltage=3.012 th0: temp=46.0 th1: temp=48.0 th2: temp=53.0 th3: temp=51.3 sysload=0.11 cputime=230.844 memavail=7396684 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2578.6: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000003 mcu_task_stddev=0.000005 bytes_write=19952869 bytes_read=2488572 bytes_retransmit=9 bytes_invalid=0 send_seq=349780 receive_seq=349780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015920 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=16360 bytes_read=52408 bytes_retransmit=0 bytes_invalid=0 send_seq=2698 receive_seq=2698 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997249 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109926 bytes_read=3496288 bytes_retransmit=9 bytes_invalid=0 send_seq=14898 receive_seq=14898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997673 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52274 bytes_read=1051871 bytes_retransmit=9 bytes_invalid=0 send_seq=6751 receive_seq=6751 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997527 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=16573 bytes_read=655078 bytes_retransmit=9 bytes_invalid=0 send_seq=2708 receive_seq=2708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17113 bytes_read=51390 bytes_retransmit=9 bytes_invalid=0 send_seq=2699 receive_seq=2699 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65685 bytes_read=1135733 bytes_retransmit=0 bytes_invalid=0 send_seq=6796 receive_seq=6796 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998632 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.0 th1: temp=47.9 th2: temp=52.8 th3: temp=51.2 sysload=0.11 cputime=230.875 memavail=7396688 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2579.6: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000003 mcu_task_stddev=0.000005 bytes_write=19952875 bytes_read=2488675 bytes_retransmit=9 bytes_invalid=0 send_seq=349781 receive_seq=349781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015926 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=16366 bytes_read=52424 bytes_retransmit=0 bytes_invalid=0 send_seq=2699 receive_seq=2699 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997226 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109932 bytes_read=3496416 bytes_retransmit=9 bytes_invalid=0 send_seq=14899 receive_seq=14899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997736 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52280 bytes_read=1052013 bytes_retransmit=9 bytes_invalid=0 send_seq=6752 receive_seq=6752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997508 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=16579 bytes_read=655372 bytes_retransmit=9 bytes_invalid=0 send_seq=2709 receive_seq=2709 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997682 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17119 bytes_read=51406 bytes_retransmit=9 bytes_invalid=0 send_seq=2700 receive_seq=2700 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65691 bytes_read=1136089 bytes_retransmit=0 bytes_invalid=0 send_seq=6797 receive_seq=6797 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998621 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=45.8 th1: temp=47.7 th2: temp=52.5 th3: temp=50.9 sysload=0.11 cputime=230.909 memavail=7394672 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2580.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19952881 bytes_read=2488821 bytes_retransmit=9 bytes_invalid=0 send_seq=349782 receive_seq=349782 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015925 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=16372 bytes_read=52440 bytes_retransmit=0 bytes_invalid=0 send_seq=2700 receive_seq=2700 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997207 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109938 bytes_read=3496516 bytes_retransmit=9 bytes_invalid=0 send_seq=14900 receive_seq=14900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997676 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52286 bytes_read=1052113 bytes_retransmit=9 bytes_invalid=0 send_seq=6753 receive_seq=6753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=16585 bytes_read=655621 bytes_retransmit=9 bytes_invalid=0 send_seq=2710 receive_seq=2710 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17125 bytes_read=51422 bytes_retransmit=9 bytes_invalid=0 send_seq=2701 receive_seq=2701 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999436 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65697 bytes_read=1136445 bytes_retransmit=0 bytes_invalid=0 send_seq=6798 receive_seq=6798 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998610 coil_temp=17.5 refs=0 mcu_temp=20.64 supply_voltage=3.012 th0: temp=45.7 th1: temp=47.6 th2: temp=52.2 th3: temp=50.7 sysload=0.11 cputime=230.942 memavail=7395808 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 2581.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19952887 bytes_read=2488924 bytes_retransmit=9 bytes_invalid=0 send_seq=349783 receive_seq=349783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015924 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16378 bytes_read=52469 bytes_retransmit=0 bytes_invalid=0 send_seq=2701 receive_seq=2701 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997204 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109944 bytes_read=3496616 bytes_retransmit=9 bytes_invalid=0 send_seq=14901 receive_seq=14901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997700 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52292 bytes_read=1052213 bytes_retransmit=9 bytes_invalid=0 send_seq=6754 receive_seq=6754 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=16591 bytes_read=655855 bytes_retransmit=9 bytes_invalid=0 send_seq=2711 receive_seq=2711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997677 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17131 bytes_read=51449 bytes_retransmit=9 bytes_invalid=0 send_seq=2702 receive_seq=2702 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65703 bytes_read=1136801 bytes_retransmit=0 bytes_invalid=0 send_seq=6799 receive_seq=6799 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998621 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=45.7 th1: temp=47.5 th2: temp=51.9 th3: temp=50.4 sysload=0.11 cputime=230.973 memavail=7395812 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2582.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19952893 bytes_read=2489027 bytes_retransmit=9 bytes_invalid=0 send_seq=349784 receive_seq=349784 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015989 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16384 bytes_read=52485 bytes_retransmit=0 bytes_invalid=0 send_seq=2702 receive_seq=2702 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997209 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109950 bytes_read=3496758 bytes_retransmit=9 bytes_invalid=0 send_seq=14902 receive_seq=14902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997668 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52298 bytes_read=1052341 bytes_retransmit=9 bytes_invalid=0 send_seq=6755 receive_seq=6755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=16597 bytes_read=656149 bytes_retransmit=9 bytes_invalid=0 send_seq=2712 receive_seq=2712 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17137 bytes_read=51465 bytes_retransmit=9 bytes_invalid=0 send_seq=2703 receive_seq=2703 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65709 bytes_read=1137157 bytes_retransmit=0 bytes_invalid=0 send_seq=6800 receive_seq=6800 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998628 coil_temp=17.5 refs=0 mcu_temp=20.66 supply_voltage=3.012 th0: temp=45.7 th1: temp=47.2 th2: temp=51.6 th3: temp=50.2 sysload=0.10 cputime=231.006 memavail=7395812 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2583.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19952899 bytes_read=2489159 bytes_retransmit=9 bytes_invalid=0 send_seq=349785 receive_seq=349785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016019 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16390 bytes_read=52501 bytes_retransmit=0 bytes_invalid=0 send_seq=2703 receive_seq=2703 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997085 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109956 bytes_read=3496858 bytes_retransmit=9 bytes_invalid=0 send_seq=14903 receive_seq=14903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997510 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52304 bytes_read=1052441 bytes_retransmit=9 bytes_invalid=0 send_seq=6756 receive_seq=6756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997334 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=16603 bytes_read=656383 bytes_retransmit=9 bytes_invalid=0 send_seq=2713 receive_seq=2713 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997544 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17143 bytes_read=51481 bytes_retransmit=9 bytes_invalid=0 send_seq=2704 receive_seq=2704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999411 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65715 bytes_read=1137513 bytes_retransmit=0 bytes_invalid=0 send_seq=6801 receive_seq=6801 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998561 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=45.6 th1: temp=47.1 th2: temp=51.4 th3: temp=50.0 sysload=0.10 cputime=231.037 memavail=7395812 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2584.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19952905 bytes_read=2489262 bytes_retransmit=9 bytes_invalid=0 send_seq=349786 receive_seq=349786 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016046 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16396 bytes_read=52517 bytes_retransmit=0 bytes_invalid=0 send_seq=2704 receive_seq=2704 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997084 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109962 bytes_read=3496958 bytes_retransmit=9 bytes_invalid=0 send_seq=14904 receive_seq=14904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997451 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=52310 bytes_read=1052555 bytes_retransmit=9 bytes_invalid=0 send_seq=6757 receive_seq=6757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997324 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=16609 bytes_read=656617 bytes_retransmit=9 bytes_invalid=0 send_seq=2714 receive_seq=2714 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997526 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17149 bytes_read=51497 bytes_retransmit=9 bytes_invalid=0 send_seq=2705 receive_seq=2705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999403 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65721 bytes_read=1137869 bytes_retransmit=0 bytes_invalid=0 send_seq=6802 receive_seq=6802 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998541 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=45.5 th1: temp=47.1 th2: temp=51.2 th3: temp=49.7 sysload=0.10 cputime=231.069 memavail=7395812 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2585.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19952911 bytes_read=2489379 bytes_retransmit=9 bytes_invalid=0 send_seq=349787 receive_seq=349787 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016030 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16402 bytes_read=52532 bytes_retransmit=0 bytes_invalid=0 send_seq=2705 receive_seq=2705 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997054 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109968 bytes_read=3497086 bytes_retransmit=9 bytes_invalid=0 send_seq=14905 receive_seq=14905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997413 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=52316 bytes_read=1052683 bytes_retransmit=9 bytes_invalid=0 send_seq=6758 receive_seq=6758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997314 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16615 bytes_read=656926 bytes_retransmit=9 bytes_invalid=0 send_seq=2715 receive_seq=2715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997495 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17155 bytes_read=51513 bytes_retransmit=9 bytes_invalid=0 send_seq=2706 receive_seq=2706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999397 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65727 bytes_read=1138225 bytes_retransmit=0 bytes_invalid=0 send_seq=6803 receive_seq=6803 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998543 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=45.5 th1: temp=46.8 th2: temp=50.9 th3: temp=49.6 sysload=0.10 cputime=231.102 memavail=7395812 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2586.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19952917 bytes_read=2489507 bytes_retransmit=9 bytes_invalid=0 send_seq=349788 receive_seq=349788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016020 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16408 bytes_read=52560 bytes_retransmit=0 bytes_invalid=0 send_seq=2706 receive_seq=2706 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997118 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109974 bytes_read=3497186 bytes_retransmit=9 bytes_invalid=0 send_seq=14906 receive_seq=14906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997486 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=52322 bytes_read=1052783 bytes_retransmit=9 bytes_invalid=0 send_seq=6759 receive_seq=6759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997388 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16621 bytes_read=657160 bytes_retransmit=9 bytes_invalid=0 send_seq=2716 receive_seq=2716 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17161 bytes_read=51540 bytes_retransmit=9 bytes_invalid=0 send_seq=2707 receive_seq=2707 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999417 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65733 bytes_read=1138581 bytes_retransmit=0 bytes_invalid=0 send_seq=6804 receive_seq=6804 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998604 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=45.5 th1: temp=46.8 th2: temp=50.7 th3: temp=49.4 sysload=0.10 cputime=231.134 memavail=7395820 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2587.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19952923 bytes_read=2489608 bytes_retransmit=9 bytes_invalid=0 send_seq=349789 receive_seq=349789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016014 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16414 bytes_read=52575 bytes_retransmit=0 bytes_invalid=0 send_seq=2707 receive_seq=2707 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997148 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109980 bytes_read=3497300 bytes_retransmit=9 bytes_invalid=0 send_seq=14907 receive_seq=14907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997643 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=52328 bytes_read=1052883 bytes_retransmit=9 bytes_invalid=0 send_seq=6760 receive_seq=6760 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997435 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16627 bytes_read=657394 bytes_retransmit=9 bytes_invalid=0 send_seq=2717 receive_seq=2717 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17167 bytes_read=51556 bytes_retransmit=9 bytes_invalid=0 send_seq=2708 receive_seq=2708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65739 bytes_read=1138937 bytes_retransmit=0 bytes_invalid=0 send_seq=6805 receive_seq=6805 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998613 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=45.4 th1: temp=46.7 th2: temp=50.5 th3: temp=49.2 sysload=0.09 cputime=231.164 memavail=7395820 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 2588.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19952929 bytes_read=2489711 bytes_retransmit=9 bytes_invalid=0 send_seq=349790 receive_seq=349790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016006 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16420 bytes_read=52590 bytes_retransmit=0 bytes_invalid=0 send_seq=2708 receive_seq=2708 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997156 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109986 bytes_read=3497428 bytes_retransmit=9 bytes_invalid=0 send_seq=14908 receive_seq=14908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997629 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=52334 bytes_read=1053011 bytes_retransmit=9 bytes_invalid=0 send_seq=6761 receive_seq=6761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997459 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16633 bytes_read=657688 bytes_retransmit=9 bytes_invalid=0 send_seq=2718 receive_seq=2718 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17173 bytes_read=51572 bytes_retransmit=9 bytes_invalid=0 send_seq=2709 receive_seq=2709 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65745 bytes_read=1139293 bytes_retransmit=0 bytes_invalid=0 send_seq=6806 receive_seq=6806 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998625 coil_temp=17.5 refs=0 mcu_temp=20.66 supply_voltage=3.012 th0: temp=45.3 th1: temp=46.7 th2: temp=50.3 th3: temp=49.0 sysload=0.09 cputime=231.196 memavail=7395596 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2589.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19952935 bytes_read=2489843 bytes_retransmit=9 bytes_invalid=0 send_seq=349791 receive_seq=349791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015998 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16426 bytes_read=52605 bytes_retransmit=0 bytes_invalid=0 send_seq=2709 receive_seq=2709 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997181 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109992 bytes_read=3497528 bytes_retransmit=9 bytes_invalid=0 send_seq=14909 receive_seq=14909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997631 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=52340 bytes_read=1053111 bytes_retransmit=9 bytes_invalid=0 send_seq=6762 receive_seq=6762 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997477 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16639 bytes_read=657922 bytes_retransmit=9 bytes_invalid=0 send_seq=2719 receive_seq=2719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17179 bytes_read=51588 bytes_retransmit=9 bytes_invalid=0 send_seq=2710 receive_seq=2710 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65751 bytes_read=1139649 bytes_retransmit=0 bytes_invalid=0 send_seq=6807 receive_seq=6807 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998642 coil_temp=17.5 refs=0 mcu_temp=20.66 supply_voltage=3.012 th0: temp=45.2 th1: temp=46.5 th2: temp=50.1 th3: temp=48.9 sysload=0.09 cputime=231.227 memavail=7395596 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2590.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19952941 bytes_read=2489960 bytes_retransmit=9 bytes_invalid=0 send_seq=349792 receive_seq=349792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015990 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16432 bytes_read=52621 bytes_retransmit=0 bytes_invalid=0 send_seq=2710 receive_seq=2710 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997215 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=109998 bytes_read=3497628 bytes_retransmit=9 bytes_invalid=0 send_seq=14910 receive_seq=14910 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997633 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52346 bytes_read=1053225 bytes_retransmit=9 bytes_invalid=0 send_seq=6763 receive_seq=6763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997507 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16645 bytes_read=658171 bytes_retransmit=9 bytes_invalid=0 send_seq=2720 receive_seq=2720 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17185 bytes_read=51604 bytes_retransmit=9 bytes_invalid=0 send_seq=2711 receive_seq=2711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65757 bytes_read=1140005 bytes_retransmit=0 bytes_invalid=0 send_seq=6808 receive_seq=6808 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998673 coil_temp=17.5 refs=0 mcu_temp=20.66 supply_voltage=3.012 th0: temp=45.2 th1: temp=46.3 th2: temp=49.9 th3: temp=48.7 sysload=0.09 cputime=231.258 memavail=7395596 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2591.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19952947 bytes_read=2490063 bytes_retransmit=9 bytes_invalid=0 send_seq=349793 receive_seq=349793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015982 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16438 bytes_read=52637 bytes_retransmit=0 bytes_invalid=0 send_seq=2711 receive_seq=2711 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997235 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110004 bytes_read=3497756 bytes_retransmit=9 bytes_invalid=0 send_seq=14911 receive_seq=14911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997631 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52352 bytes_read=1053353 bytes_retransmit=9 bytes_invalid=0 send_seq=6764 receive_seq=6764 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997537 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16651 bytes_read=658465 bytes_retransmit=9 bytes_invalid=0 send_seq=2721 receive_seq=2721 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17191 bytes_read=51631 bytes_retransmit=9 bytes_invalid=0 send_seq=2712 receive_seq=2712 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65763 bytes_read=1140361 bytes_retransmit=0 bytes_invalid=0 send_seq=6809 receive_seq=6809 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998663 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=45.1 th1: temp=46.3 th2: temp=49.8 th3: temp=48.6 sysload=0.09 cputime=231.290 memavail=7395596 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2592.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19952953 bytes_read=2490195 bytes_retransmit=9 bytes_invalid=0 send_seq=349794 receive_seq=349794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015976 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16444 bytes_read=52666 bytes_retransmit=0 bytes_invalid=0 send_seq=2712 receive_seq=2712 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997247 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110010 bytes_read=3497856 bytes_retransmit=9 bytes_invalid=0 send_seq=14912 receive_seq=14912 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997631 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52358 bytes_read=1053453 bytes_retransmit=9 bytes_invalid=0 send_seq=6765 receive_seq=6765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997537 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16657 bytes_read=658699 bytes_retransmit=9 bytes_invalid=0 send_seq=2722 receive_seq=2722 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17197 bytes_read=51647 bytes_retransmit=9 bytes_invalid=0 send_seq=2713 receive_seq=2713 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65769 bytes_read=1140717 bytes_retransmit=0 bytes_invalid=0 send_seq=6810 receive_seq=6810 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998657 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=44.9 th1: temp=46.1 th2: temp=49.4 th3: temp=48.3 sysload=0.08 cputime=231.323 memavail=7395596 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2593.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19952959 bytes_read=2490298 bytes_retransmit=9 bytes_invalid=0 send_seq=349795 receive_seq=349795 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015968 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16450 bytes_read=52682 bytes_retransmit=0 bytes_invalid=0 send_seq=2713 receive_seq=2713 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997264 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110016 bytes_read=3497968 bytes_retransmit=9 bytes_invalid=0 send_seq=14913 receive_seq=14913 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997630 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52364 bytes_read=1053551 bytes_retransmit=9 bytes_invalid=0 send_seq=6766 receive_seq=6766 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16663 bytes_read=658933 bytes_retransmit=9 bytes_invalid=0 send_seq=2723 receive_seq=2723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17203 bytes_read=51663 bytes_retransmit=9 bytes_invalid=0 send_seq=2714 receive_seq=2714 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65775 bytes_read=1141073 bytes_retransmit=0 bytes_invalid=0 send_seq=6811 receive_seq=6811 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998657 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=44.9 th1: temp=46.2 th2: temp=49.5 th3: temp=48.3 sysload=0.08 cputime=231.354 memavail=7395624 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2594.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19952965 bytes_read=2490401 bytes_retransmit=9 bytes_invalid=0 send_seq=349796 receive_seq=349796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015983 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16456 bytes_read=52698 bytes_retransmit=0 bytes_invalid=0 send_seq=2714 receive_seq=2714 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997247 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110022 bytes_read=3498087 bytes_retransmit=9 bytes_invalid=0 send_seq=14914 receive_seq=14914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997628 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52370 bytes_read=1053670 bytes_retransmit=9 bytes_invalid=0 send_seq=6767 receive_seq=6767 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997565 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16669 bytes_read=659227 bytes_retransmit=9 bytes_invalid=0 send_seq=2724 receive_seq=2724 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17209 bytes_read=51679 bytes_retransmit=9 bytes_invalid=0 send_seq=2715 receive_seq=2715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65781 bytes_read=1141429 bytes_retransmit=0 bytes_invalid=0 send_seq=6812 receive_seq=6812 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998655 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=44.9 th1: temp=46.0 th2: temp=49.2 th3: temp=48.2 sysload=0.08 cputime=231.387 memavail=7395624 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2595.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19952971 bytes_read=2490547 bytes_retransmit=9 bytes_invalid=0 send_seq=349797 receive_seq=349797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015976 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16462 bytes_read=52714 bytes_retransmit=0 bytes_invalid=0 send_seq=2715 receive_seq=2715 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997224 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110028 bytes_read=3498180 bytes_retransmit=9 bytes_invalid=0 send_seq=14915 receive_seq=14915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997595 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=52376 bytes_read=1053777 bytes_retransmit=9 bytes_invalid=0 send_seq=6768 receive_seq=6768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16675 bytes_read=659476 bytes_retransmit=9 bytes_invalid=0 send_seq=2725 receive_seq=2725 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997623 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17215 bytes_read=51695 bytes_retransmit=9 bytes_invalid=0 send_seq=2716 receive_seq=2716 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65787 bytes_read=1141785 bytes_retransmit=0 bytes_invalid=0 send_seq=6813 receive_seq=6813 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998636 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=44.8 th1: temp=46.0 th2: temp=49.1 th3: temp=48.0 sysload=0.08 cputime=231.420 memavail=7395896 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2596.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19952977 bytes_read=2490650 bytes_retransmit=9 bytes_invalid=0 send_seq=349798 receive_seq=349798 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015967 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16468 bytes_read=52730 bytes_retransmit=0 bytes_invalid=0 send_seq=2716 receive_seq=2716 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997232 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110034 bytes_read=3498273 bytes_retransmit=9 bytes_invalid=0 send_seq=14916 receive_seq=14916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997605 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=52382 bytes_read=1053870 bytes_retransmit=9 bytes_invalid=0 send_seq=6769 receive_seq=6769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997513 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16681 bytes_read=659710 bytes_retransmit=9 bytes_invalid=0 send_seq=2726 receive_seq=2726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997634 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17221 bytes_read=51722 bytes_retransmit=9 bytes_invalid=0 send_seq=2717 receive_seq=2717 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999456 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65793 bytes_read=1142141 bytes_retransmit=0 bytes_invalid=0 send_seq=6814 receive_seq=6814 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998644 coil_temp=17.5 refs=0 mcu_temp=20.70 supply_voltage=3.012 th0: temp=44.8 th1: temp=45.9 th2: temp=49.0 th3: temp=47.9 sysload=0.08 cputime=231.451 memavail=7395896 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2597.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19952983 bytes_read=2490749 bytes_retransmit=9 bytes_invalid=0 send_seq=349799 receive_seq=349799 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015969 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16474 bytes_read=52759 bytes_retransmit=0 bytes_invalid=0 send_seq=2717 receive_seq=2717 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999233 adj=49997240 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110040 bytes_read=3498394 bytes_retransmit=9 bytes_invalid=0 send_seq=14917 receive_seq=14917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997615 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=52388 bytes_read=1053991 bytes_retransmit=9 bytes_invalid=0 send_seq=6770 receive_seq=6770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997522 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16687 bytes_read=660004 bytes_retransmit=9 bytes_invalid=0 send_seq=2727 receive_seq=2727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17227 bytes_read=51738 bytes_retransmit=9 bytes_invalid=0 send_seq=2718 receive_seq=2718 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65799 bytes_read=1142497 bytes_retransmit=0 bytes_invalid=0 send_seq=6815 receive_seq=6815 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998644 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=44.8 th1: temp=45.8 th2: temp=48.7 th3: temp=47.7 sysload=0.08 cputime=231.488 memavail=7399788 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2598.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19952989 bytes_read=2490881 bytes_retransmit=9 bytes_invalid=0 send_seq=349800 receive_seq=349800 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015967 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16480 bytes_read=52775 bytes_retransmit=0 bytes_invalid=0 send_seq=2718 receive_seq=2718 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999232 adj=49997225 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=110046 bytes_read=3498508 bytes_retransmit=9 bytes_invalid=0 send_seq=14918 receive_seq=14918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997602 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=52394 bytes_read=1054091 bytes_retransmit=9 bytes_invalid=0 send_seq=6771 receive_seq=6771 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997502 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16693 bytes_read=660238 bytes_retransmit=9 bytes_invalid=0 send_seq=2728 receive_seq=2728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17233 bytes_read=51754 bytes_retransmit=9 bytes_invalid=0 send_seq=2719 receive_seq=2719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65805 bytes_read=1142853 bytes_retransmit=0 bytes_invalid=0 send_seq=6816 receive_seq=6816 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998634 coil_temp=17.5 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=44.8 th1: temp=45.7 th2: temp=48.7 th3: temp=47.6 sysload=0.08 cputime=231.520 memavail=7399788 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2599.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19952995 bytes_read=2490984 bytes_retransmit=9 bytes_invalid=0 send_seq=349801 receive_seq=349801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015962 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16486 bytes_read=52791 bytes_retransmit=0 bytes_invalid=0 send_seq=2719 receive_seq=2719 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999230 adj=49997210 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=110052 bytes_read=3498608 bytes_retransmit=9 bytes_invalid=0 send_seq=14919 receive_seq=14919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997601 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=52400 bytes_read=1054191 bytes_retransmit=9 bytes_invalid=0 send_seq=6772 receive_seq=6772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997499 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16699 bytes_read=660472 bytes_retransmit=9 bytes_invalid=0 send_seq=2729 receive_seq=2729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17239 bytes_read=51770 bytes_retransmit=9 bytes_invalid=0 send_seq=2720 receive_seq=2720 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999479 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65811 bytes_read=1143209 bytes_retransmit=0 bytes_invalid=0 send_seq=6817 receive_seq=6817 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998643 coil_temp=17.5 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=44.7 th1: temp=45.7 th2: temp=48.6 th3: temp=47.6 sysload=0.08 cputime=231.552 memavail=7399788 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2600.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953001 bytes_read=2491101 bytes_retransmit=9 bytes_invalid=0 send_seq=349802 receive_seq=349802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016003 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16492 bytes_read=52807 bytes_retransmit=0 bytes_invalid=0 send_seq=2720 receive_seq=2720 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999230 adj=49997206 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=110058 bytes_read=3498736 bytes_retransmit=9 bytes_invalid=0 send_seq=14920 receive_seq=14920 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997609 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=52406 bytes_read=1054333 bytes_retransmit=9 bytes_invalid=0 send_seq=6773 receive_seq=6773 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16705 bytes_read=660781 bytes_retransmit=9 bytes_invalid=0 send_seq=2730 receive_seq=2730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17245 bytes_read=51786 bytes_retransmit=9 bytes_invalid=0 send_seq=2721 receive_seq=2721 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999469 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65817 bytes_read=1143565 bytes_retransmit=0 bytes_invalid=0 send_seq=6818 receive_seq=6818 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998668 coil_temp=17.5 refs=0 mcu_temp=20.70 supply_voltage=3.012 th0: temp=44.6 th1: temp=45.6 th2: temp=48.4 th3: temp=47.4 sysload=0.08 cputime=231.585 memavail=7399788 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2601.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953007 bytes_read=2491233 bytes_retransmit=9 bytes_invalid=0 send_seq=349803 receive_seq=349803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016001 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16498 bytes_read=52823 bytes_retransmit=0 bytes_invalid=0 send_seq=2721 receive_seq=2721 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999230 adj=49997127 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=110064 bytes_read=3498836 bytes_retransmit=9 bytes_invalid=0 send_seq=14921 receive_seq=14921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997513 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=52412 bytes_read=1054433 bytes_retransmit=9 bytes_invalid=0 send_seq=6774 receive_seq=6774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997391 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16711 bytes_read=661015 bytes_retransmit=9 bytes_invalid=0 send_seq=2731 receive_seq=2731 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997553 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17251 bytes_read=51813 bytes_retransmit=9 bytes_invalid=0 send_seq=2722 receive_seq=2722 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65823 bytes_read=1143921 bytes_retransmit=0 bytes_invalid=0 send_seq=6819 receive_seq=6819 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998607 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=44.6 th1: temp=45.6 th2: temp=48.4 th3: temp=47.4 sysload=0.08 cputime=231.617 memavail=7399788 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2602.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953013 bytes_read=2491336 bytes_retransmit=9 bytes_invalid=0 send_seq=349804 receive_seq=349804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015992 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=16504 bytes_read=52852 bytes_retransmit=0 bytes_invalid=0 send_seq=2722 receive_seq=2722 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999231 adj=49997164 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=110070 bytes_read=3498936 bytes_retransmit=9 bytes_invalid=0 send_seq=14922 receive_seq=14922 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997554 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=52418 bytes_read=1054533 bytes_retransmit=9 bytes_invalid=0 send_seq=6775 receive_seq=6775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997421 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16717 bytes_read=661249 bytes_retransmit=9 bytes_invalid=0 send_seq=2732 receive_seq=2732 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997570 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17257 bytes_read=51829 bytes_retransmit=9 bytes_invalid=0 send_seq=2723 receive_seq=2723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65829 bytes_read=1144277 bytes_retransmit=0 bytes_invalid=0 send_seq=6820 receive_seq=6820 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998620 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=44.5 th1: temp=45.5 th2: temp=48.3 th3: temp=47.3 sysload=0.07 cputime=231.648 memavail=7399788 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2603.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953019 bytes_read=2491439 bytes_retransmit=9 bytes_invalid=0 send_seq=349805 receive_seq=349805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015984 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=16510 bytes_read=52868 bytes_retransmit=0 bytes_invalid=0 send_seq=2723 receive_seq=2723 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999231 adj=49997202 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110076 bytes_read=3499078 bytes_retransmit=9 bytes_invalid=0 send_seq=14923 receive_seq=14923 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997581 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=52424 bytes_read=1054661 bytes_retransmit=9 bytes_invalid=0 send_seq=6776 receive_seq=6776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997452 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16749 bytes_read=661553 bytes_retransmit=9 bytes_invalid=0 send_seq=2735 receive_seq=2735 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997597 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17263 bytes_read=51845 bytes_retransmit=9 bytes_invalid=0 send_seq=2724 receive_seq=2724 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65835 bytes_read=1144633 bytes_retransmit=0 bytes_invalid=0 send_seq=6821 receive_seq=6821 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998640 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=44.5 th1: temp=45.5 th2: temp=48.1 th3: temp=47.1 sysload=0.07 cputime=231.680 memavail=7399788 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2604.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953025 bytes_read=2491571 bytes_retransmit=9 bytes_invalid=0 send_seq=349806 receive_seq=349806 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016005 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=16516 bytes_read=52884 bytes_retransmit=0 bytes_invalid=0 send_seq=2724 receive_seq=2724 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999232 adj=49997235 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110082 bytes_read=3499178 bytes_retransmit=9 bytes_invalid=0 send_seq=14924 receive_seq=14924 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997598 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=52430 bytes_read=1054761 bytes_retransmit=9 bytes_invalid=0 send_seq=6777 receive_seq=6777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997483 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16755 bytes_read=661787 bytes_retransmit=9 bytes_invalid=0 send_seq=2736 receive_seq=2736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997609 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17269 bytes_read=51861 bytes_retransmit=9 bytes_invalid=0 send_seq=2725 receive_seq=2725 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65841 bytes_read=1144989 bytes_retransmit=0 bytes_invalid=0 send_seq=6822 receive_seq=6822 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998654 coil_temp=17.5 refs=0 mcu_temp=20.70 supply_voltage=3.012 th0: temp=44.4 th1: temp=45.3 th2: temp=48.0 th3: temp=47.1 sysload=0.07 cputime=231.713 memavail=7399048 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2605.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953031 bytes_read=2491674 bytes_retransmit=9 bytes_invalid=0 send_seq=349807 receive_seq=349807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015999 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=16522 bytes_read=52900 bytes_retransmit=0 bytes_invalid=0 send_seq=2725 receive_seq=2725 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999231 adj=49997201 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110088 bytes_read=3499278 bytes_retransmit=9 bytes_invalid=0 send_seq=14925 receive_seq=14925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997580 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52436 bytes_read=1054875 bytes_retransmit=9 bytes_invalid=0 send_seq=6778 receive_seq=6778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997427 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16761 bytes_read=662036 bytes_retransmit=9 bytes_invalid=0 send_seq=2737 receive_seq=2737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997583 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17275 bytes_read=51877 bytes_retransmit=9 bytes_invalid=0 send_seq=2726 receive_seq=2726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65847 bytes_read=1145345 bytes_retransmit=0 bytes_invalid=0 send_seq=6823 receive_seq=6823 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998633 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=44.4 th1: temp=45.3 th2: temp=48.0 th3: temp=47.0 sysload=0.07 cputime=231.744 memavail=7398588 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2606.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953037 bytes_read=2491791 bytes_retransmit=9 bytes_invalid=0 send_seq=349808 receive_seq=349808 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015994 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=16528 bytes_read=52916 bytes_retransmit=0 bytes_invalid=0 send_seq=2726 receive_seq=2726 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999232 adj=49997217 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110094 bytes_read=3499406 bytes_retransmit=9 bytes_invalid=0 send_seq=14926 receive_seq=14926 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997598 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52442 bytes_read=1055003 bytes_retransmit=9 bytes_invalid=0 send_seq=6779 receive_seq=6779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997464 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16767 bytes_read=662330 bytes_retransmit=9 bytes_invalid=0 send_seq=2738 receive_seq=2738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997598 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17281 bytes_read=51904 bytes_retransmit=9 bytes_invalid=0 send_seq=2727 receive_seq=2727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999430 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65853 bytes_read=1145701 bytes_retransmit=0 bytes_invalid=0 send_seq=6824 receive_seq=6824 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998693 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=44.4 th1: temp=45.4 th2: temp=47.8 th3: temp=46.9 sysload=0.07 cputime=231.778 memavail=7398588 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2607.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953043 bytes_read=2491923 bytes_retransmit=9 bytes_invalid=0 send_seq=349809 receive_seq=349809 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015985 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16534 bytes_read=52945 bytes_retransmit=0 bytes_invalid=0 send_seq=2727 receive_seq=2727 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999231 adj=49997234 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110100 bytes_read=3499506 bytes_retransmit=9 bytes_invalid=0 send_seq=14927 receive_seq=14927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997656 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52448 bytes_read=1055103 bytes_retransmit=9 bytes_invalid=0 send_seq=6780 receive_seq=6780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997477 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16773 bytes_read=662564 bytes_retransmit=9 bytes_invalid=0 send_seq=2739 receive_seq=2739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997611 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17287 bytes_read=51920 bytes_retransmit=9 bytes_invalid=0 send_seq=2728 receive_seq=2728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999431 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65859 bytes_read=1146041 bytes_retransmit=0 bytes_invalid=0 send_seq=6825 receive_seq=6825 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998676 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=44.3 th1: temp=45.2 th2: temp=47.7 th3: temp=46.8 sysload=0.07 cputime=231.809 memavail=7398588 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2608.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953049 bytes_read=2492022 bytes_retransmit=9 bytes_invalid=0 send_seq=349810 receive_seq=349810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015980 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16540 bytes_read=52961 bytes_retransmit=0 bytes_invalid=0 send_seq=2728 receive_seq=2728 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999233 adj=49997249 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110106 bytes_read=3499620 bytes_retransmit=9 bytes_invalid=0 send_seq=14928 receive_seq=14928 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997666 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52454 bytes_read=1055203 bytes_retransmit=9 bytes_invalid=0 send_seq=6781 receive_seq=6781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997494 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16779 bytes_read=662798 bytes_retransmit=9 bytes_invalid=0 send_seq=2740 receive_seq=2740 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17293 bytes_read=51936 bytes_retransmit=9 bytes_invalid=0 send_seq=2729 receive_seq=2729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65865 bytes_read=1146397 bytes_retransmit=0 bytes_invalid=0 send_seq=6826 receive_seq=6826 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998679 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=44.3 th1: temp=45.2 th2: temp=47.6 th3: temp=46.8 sysload=0.07 cputime=231.841 memavail=7398588 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 2609.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953055 bytes_read=2492125 bytes_retransmit=9 bytes_invalid=0 send_seq=349811 receive_seq=349811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015976 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16546 bytes_read=52977 bytes_retransmit=0 bytes_invalid=0 send_seq=2729 receive_seq=2729 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999233 adj=49997277 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110112 bytes_read=3499748 bytes_retransmit=9 bytes_invalid=0 send_seq=14929 receive_seq=14929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997666 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52460 bytes_read=1055331 bytes_retransmit=9 bytes_invalid=0 send_seq=6782 receive_seq=6782 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997501 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=16785 bytes_read=663092 bytes_retransmit=9 bytes_invalid=0 send_seq=2741 receive_seq=2741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17299 bytes_read=51952 bytes_retransmit=9 bytes_invalid=0 send_seq=2730 receive_seq=2730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65871 bytes_read=1146753 bytes_retransmit=0 bytes_invalid=0 send_seq=6827 receive_seq=6827 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998669 coil_temp=17.5 refs=0 mcu_temp=20.68 supply_voltage=3.012 th0: temp=44.2 th1: temp=45.1 th2: temp=47.6 th3: temp=46.8 sysload=0.07 cputime=231.873 memavail=7398588 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2610.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953061 bytes_read=2492257 bytes_retransmit=9 bytes_invalid=0 send_seq=349812 receive_seq=349812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015977 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16552 bytes_read=52993 bytes_retransmit=0 bytes_invalid=0 send_seq=2730 receive_seq=2730 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999232 adj=49997272 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110118 bytes_read=3499848 bytes_retransmit=9 bytes_invalid=0 send_seq=14930 receive_seq=14930 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997660 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52466 bytes_read=1055445 bytes_retransmit=9 bytes_invalid=0 send_seq=6783 receive_seq=6783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997512 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16791 bytes_read=663341 bytes_retransmit=9 bytes_invalid=0 send_seq=2742 receive_seq=2742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997698 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17305 bytes_read=51968 bytes_retransmit=9 bytes_invalid=0 send_seq=2731 receive_seq=2731 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65877 bytes_read=1147109 bytes_retransmit=0 bytes_invalid=0 send_seq=6828 receive_seq=6828 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998665 coil_temp=17.5 refs=0 mcu_temp=20.68 supply_voltage=3.012 th0: temp=44.2 th1: temp=45.1 th2: temp=47.5 th3: temp=46.6 sysload=0.07 cputime=231.905 memavail=7398588 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2611.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953067 bytes_read=2492374 bytes_retransmit=9 bytes_invalid=0 send_seq=349813 receive_seq=349813 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015976 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16558 bytes_read=53009 bytes_retransmit=0 bytes_invalid=0 send_seq=2731 receive_seq=2731 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999233 adj=49997252 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110124 bytes_read=3499948 bytes_retransmit=9 bytes_invalid=0 send_seq=14931 receive_seq=14931 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997664 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52472 bytes_read=1055545 bytes_retransmit=9 bytes_invalid=0 send_seq=6784 receive_seq=6784 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16797 bytes_read=663575 bytes_retransmit=9 bytes_invalid=0 send_seq=2743 receive_seq=2743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997737 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17311 bytes_read=51995 bytes_retransmit=9 bytes_invalid=0 send_seq=2732 receive_seq=2732 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999455 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65883 bytes_read=1147465 bytes_retransmit=0 bytes_invalid=0 send_seq=6829 receive_seq=6829 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998690 coil_temp=17.5 refs=0 mcu_temp=20.68 supply_voltage=3.012 th0: temp=44.1 th1: temp=45.1 th2: temp=47.4 th3: temp=46.6 sysload=0.07 cputime=231.937 memavail=7398588 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2612.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953073 bytes_read=2492477 bytes_retransmit=9 bytes_invalid=0 send_seq=349814 receive_seq=349814 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015972 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16564 bytes_read=53038 bytes_retransmit=0 bytes_invalid=0 send_seq=2732 receive_seq=2732 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997260 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110130 bytes_read=3500076 bytes_retransmit=9 bytes_invalid=0 send_seq=14932 receive_seq=14932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997760 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52478 bytes_read=1055673 bytes_retransmit=9 bytes_invalid=0 send_seq=6785 receive_seq=6785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997514 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16803 bytes_read=663869 bytes_retransmit=9 bytes_invalid=0 send_seq=2744 receive_seq=2744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997702 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17317 bytes_read=52011 bytes_retransmit=9 bytes_invalid=0 send_seq=2733 receive_seq=2733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65889 bytes_read=1147821 bytes_retransmit=0 bytes_invalid=0 send_seq=6830 receive_seq=6830 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998676 coil_temp=17.5 refs=0 mcu_temp=20.68 supply_voltage=3.012 th0: temp=44.2 th1: temp=44.9 th2: temp=47.3 th3: temp=46.5 sysload=0.06 cputime=231.969 memavail=7398596 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2613.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953079 bytes_read=2492609 bytes_retransmit=9 bytes_invalid=0 send_seq=349815 receive_seq=349815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015965 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16570 bytes_read=53054 bytes_retransmit=0 bytes_invalid=0 send_seq=2733 receive_seq=2733 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997343 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110136 bytes_read=3500190 bytes_retransmit=9 bytes_invalid=0 send_seq=14933 receive_seq=14933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997727 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52484 bytes_read=1055773 bytes_retransmit=9 bytes_invalid=0 send_seq=6786 receive_seq=6786 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16809 bytes_read=664103 bytes_retransmit=9 bytes_invalid=0 send_seq=2745 receive_seq=2745 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997697 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17323 bytes_read=52027 bytes_retransmit=9 bytes_invalid=0 send_seq=2734 receive_seq=2734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999445 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65895 bytes_read=1148177 bytes_retransmit=0 bytes_invalid=0 send_seq=6831 receive_seq=6831 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998661 coil_temp=17.5 refs=0 mcu_temp=20.68 supply_voltage=3.012 th0: temp=44.0 th1: temp=44.9 th2: temp=47.3 th3: temp=46.4 sysload=0.06 cputime=232.003 memavail=7398596 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2614.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953085 bytes_read=2492712 bytes_retransmit=9 bytes_invalid=0 send_seq=349816 receive_seq=349816 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015969 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16576 bytes_read=53070 bytes_retransmit=0 bytes_invalid=0 send_seq=2734 receive_seq=2734 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997338 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110142 bytes_read=3500290 bytes_retransmit=9 bytes_invalid=0 send_seq=14934 receive_seq=14934 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997704 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52490 bytes_read=1055873 bytes_retransmit=9 bytes_invalid=0 send_seq=6787 receive_seq=6787 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997522 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16815 bytes_read=664337 bytes_retransmit=9 bytes_invalid=0 send_seq=2746 receive_seq=2746 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17329 bytes_read=52043 bytes_retransmit=9 bytes_invalid=0 send_seq=2735 receive_seq=2735 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65901 bytes_read=1148533 bytes_retransmit=0 bytes_invalid=0 send_seq=6832 receive_seq=6832 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998699 coil_temp=17.5 refs=0 mcu_temp=20.68 supply_voltage=3.012 th0: temp=44.1 th1: temp=45.0 th2: temp=47.2 th3: temp=46.4 sysload=0.06 cputime=232.039 memavail=7398108 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2615.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953091 bytes_read=2492815 bytes_retransmit=9 bytes_invalid=0 send_seq=349817 receive_seq=349817 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015986 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16582 bytes_read=53086 bytes_retransmit=0 bytes_invalid=0 send_seq=2735 receive_seq=2735 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997304 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110148 bytes_read=3500418 bytes_retransmit=9 bytes_invalid=0 send_seq=14935 receive_seq=14935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997701 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52496 bytes_read=1056015 bytes_retransmit=9 bytes_invalid=0 send_seq=6788 receive_seq=6788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16821 bytes_read=664646 bytes_retransmit=9 bytes_invalid=0 send_seq=2747 receive_seq=2747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17335 bytes_read=52059 bytes_retransmit=9 bytes_invalid=0 send_seq=2736 receive_seq=2736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999445 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65907 bytes_read=1148889 bytes_retransmit=0 bytes_invalid=0 send_seq=6833 receive_seq=6833 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998675 coil_temp=17.5 refs=0 mcu_temp=20.68 supply_voltage=3.012 th0: temp=44.1 th1: temp=44.8 th2: temp=47.1 th3: temp=46.3 sysload=0.06 cputime=232.072 memavail=7397484 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2616.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953097 bytes_read=2492961 bytes_retransmit=9 bytes_invalid=0 send_seq=349818 receive_seq=349818 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015980 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16588 bytes_read=53102 bytes_retransmit=0 bytes_invalid=0 send_seq=2736 receive_seq=2736 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997256 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110154 bytes_read=3500518 bytes_retransmit=9 bytes_invalid=0 send_seq=14936 receive_seq=14936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997654 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52502 bytes_read=1056115 bytes_retransmit=9 bytes_invalid=0 send_seq=6789 receive_seq=6789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997462 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16827 bytes_read=664880 bytes_retransmit=9 bytes_invalid=0 send_seq=2748 receive_seq=2748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997610 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17341 bytes_read=52086 bytes_retransmit=9 bytes_invalid=0 send_seq=2737 receive_seq=2737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999432 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65913 bytes_read=1149245 bytes_retransmit=0 bytes_invalid=0 send_seq=6834 receive_seq=6834 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998655 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=44.0 th1: temp=44.8 th2: temp=47.1 th3: temp=46.3 sysload=0.06 cputime=232.104 memavail=7397260 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2617.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953103 bytes_read=2493064 bytes_retransmit=9 bytes_invalid=0 send_seq=349819 receive_seq=349819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015979 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16594 bytes_read=53131 bytes_retransmit=0 bytes_invalid=0 send_seq=2737 receive_seq=2737 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997239 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110160 bytes_read=3500618 bytes_retransmit=9 bytes_invalid=0 send_seq=14937 receive_seq=14937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997660 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52508 bytes_read=1056215 bytes_retransmit=9 bytes_invalid=0 send_seq=6790 receive_seq=6790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997484 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16833 bytes_read=665114 bytes_retransmit=9 bytes_invalid=0 send_seq=2749 receive_seq=2749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997615 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17347 bytes_read=52102 bytes_retransmit=9 bytes_invalid=0 send_seq=2738 receive_seq=2738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999447 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65919 bytes_read=1149601 bytes_retransmit=0 bytes_invalid=0 send_seq=6835 receive_seq=6835 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998702 coil_temp=17.5 refs=0 mcu_temp=20.70 supply_voltage=3.012 th0: temp=43.9 th1: temp=44.8 th2: temp=47.0 th3: temp=46.2 sysload=0.06 cputime=232.136 memavail=7397260 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2618.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953109 bytes_read=2493167 bytes_retransmit=9 bytes_invalid=0 send_seq=349820 receive_seq=349820 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015970 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16600 bytes_read=53147 bytes_retransmit=0 bytes_invalid=0 send_seq=2738 receive_seq=2738 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997217 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110166 bytes_read=3500760 bytes_retransmit=9 bytes_invalid=0 send_seq=14938 receive_seq=14938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997644 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52514 bytes_read=1056343 bytes_retransmit=9 bytes_invalid=0 send_seq=6791 receive_seq=6791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997507 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16839 bytes_read=665408 bytes_retransmit=9 bytes_invalid=0 send_seq=2750 receive_seq=2750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997614 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17353 bytes_read=52118 bytes_retransmit=9 bytes_invalid=0 send_seq=2739 receive_seq=2739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65925 bytes_read=1149957 bytes_retransmit=0 bytes_invalid=0 send_seq=6836 receive_seq=6836 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998675 coil_temp=17.5 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=43.9 th1: temp=44.7 th2: temp=46.9 th3: temp=46.1 sysload=0.06 cputime=232.169 memavail=7397260 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2619.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953115 bytes_read=2493294 bytes_retransmit=9 bytes_invalid=0 send_seq=349821 receive_seq=349821 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015965 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16606 bytes_read=53163 bytes_retransmit=0 bytes_invalid=0 send_seq=2739 receive_seq=2739 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997235 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110172 bytes_read=3500860 bytes_retransmit=9 bytes_invalid=0 send_seq=14939 receive_seq=14939 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997667 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52520 bytes_read=1056443 bytes_retransmit=9 bytes_invalid=0 send_seq=6792 receive_seq=6792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997536 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16845 bytes_read=665642 bytes_retransmit=9 bytes_invalid=0 send_seq=2751 receive_seq=2751 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17359 bytes_read=52134 bytes_retransmit=9 bytes_invalid=0 send_seq=2740 receive_seq=2740 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999470 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65931 bytes_read=1150313 bytes_retransmit=0 bytes_invalid=0 send_seq=6837 receive_seq=6837 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998720 coil_temp=17.5 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=43.9 th1: temp=44.7 th2: temp=46.9 th3: temp=46.2 sysload=0.06 cputime=232.201 memavail=7397264 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2620.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953121 bytes_read=2493397 bytes_retransmit=9 bytes_invalid=0 send_seq=349822 receive_seq=349822 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015957 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16612 bytes_read=53179 bytes_retransmit=0 bytes_invalid=0 send_seq=2740 receive_seq=2740 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997325 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110178 bytes_read=3500960 bytes_retransmit=9 bytes_invalid=0 send_seq=14940 receive_seq=14940 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997659 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=52526 bytes_read=1056557 bytes_retransmit=9 bytes_invalid=0 send_seq=6793 receive_seq=6793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997530 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16851 bytes_read=665891 bytes_retransmit=9 bytes_invalid=0 send_seq=2752 receive_seq=2752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997694 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17365 bytes_read=52150 bytes_retransmit=9 bytes_invalid=0 send_seq=2741 receive_seq=2741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999466 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65937 bytes_read=1150669 bytes_retransmit=0 bytes_invalid=0 send_seq=6838 receive_seq=6838 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998691 coil_temp=17.5 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=43.8 th1: temp=44.6 th2: temp=46.8 th3: temp=46.0 sysload=0.06 cputime=232.234 memavail=7397264 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2621.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953127 bytes_read=2493514 bytes_retransmit=9 bytes_invalid=0 send_seq=349823 receive_seq=349823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015951 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16618 bytes_read=53195 bytes_retransmit=0 bytes_invalid=0 send_seq=2741 receive_seq=2741 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997405 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110184 bytes_read=3501088 bytes_retransmit=9 bytes_invalid=0 send_seq=14941 receive_seq=14941 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997662 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=52532 bytes_read=1056685 bytes_retransmit=9 bytes_invalid=0 send_seq=6794 receive_seq=6794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16857 bytes_read=666185 bytes_retransmit=9 bytes_invalid=0 send_seq=2753 receive_seq=2753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17371 bytes_read=52177 bytes_retransmit=9 bytes_invalid=0 send_seq=2742 receive_seq=2742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999457 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65943 bytes_read=1151025 bytes_retransmit=0 bytes_invalid=0 send_seq=6839 receive_seq=6839 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998673 coil_temp=17.5 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=43.8 th1: temp=44.6 th2: temp=46.7 th3: temp=46.0 sysload=0.06 cputime=232.266 memavail=7397264 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2622.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953133 bytes_read=2493646 bytes_retransmit=9 bytes_invalid=0 send_seq=349824 receive_seq=349824 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015952 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16624 bytes_read=53224 bytes_retransmit=0 bytes_invalid=0 send_seq=2742 receive_seq=2742 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997450 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110190 bytes_read=3501188 bytes_retransmit=9 bytes_invalid=0 send_seq=14942 receive_seq=14942 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997659 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=52538 bytes_read=1056785 bytes_retransmit=9 bytes_invalid=0 send_seq=6795 receive_seq=6795 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16863 bytes_read=666419 bytes_retransmit=9 bytes_invalid=0 send_seq=2754 receive_seq=2754 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17377 bytes_read=52193 bytes_retransmit=9 bytes_invalid=0 send_seq=2743 receive_seq=2743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65949 bytes_read=1151381 bytes_retransmit=0 bytes_invalid=0 send_seq=6840 receive_seq=6840 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998659 coil_temp=17.5 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=43.8 th1: temp=44.5 th2: temp=46.7 th3: temp=45.9 sysload=0.05 cputime=232.298 memavail=7397264 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2623.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953139 bytes_read=2493749 bytes_retransmit=9 bytes_invalid=0 send_seq=349825 receive_seq=349825 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015953 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16630 bytes_read=53240 bytes_retransmit=0 bytes_invalid=0 send_seq=2743 receive_seq=2743 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997454 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=110196 bytes_read=3501302 bytes_retransmit=9 bytes_invalid=0 send_seq=14943 receive_seq=14943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997639 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=52544 bytes_read=1056885 bytes_retransmit=9 bytes_invalid=0 send_seq=6796 receive_seq=6796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16869 bytes_read=666653 bytes_retransmit=9 bytes_invalid=0 send_seq=2755 receive_seq=2755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17383 bytes_read=52209 bytes_retransmit=9 bytes_invalid=0 send_seq=2744 receive_seq=2744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999443 Octopus_Pro_H723_V1.1: temp=30.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65955 bytes_read=1151737 bytes_retransmit=0 bytes_invalid=0 send_seq=6841 receive_seq=6841 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998648 coil_temp=17.5 refs=0 mcu_temp=20.73 supply_voltage=3.012 th0: temp=43.8 th1: temp=44.5 th2: temp=46.7 th3: temp=45.9 sysload=0.05 cputime=232.330 memavail=7397264 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2624.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953145 bytes_read=2493852 bytes_retransmit=9 bytes_invalid=0 send_seq=349826 receive_seq=349826 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015949 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16636 bytes_read=53256 bytes_retransmit=0 bytes_invalid=0 send_seq=2744 receive_seq=2744 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999260 adj=49997478 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=110202 bytes_read=3501430 bytes_retransmit=9 bytes_invalid=0 send_seq=14944 receive_seq=14944 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997625 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=52550 bytes_read=1057013 bytes_retransmit=9 bytes_invalid=0 send_seq=6797 receive_seq=6797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16875 bytes_read=666947 bytes_retransmit=9 bytes_invalid=0 send_seq=2756 receive_seq=2756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17389 bytes_read=52225 bytes_retransmit=9 bytes_invalid=0 send_seq=2745 receive_seq=2745 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999439 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65961 bytes_read=1152093 bytes_retransmit=0 bytes_invalid=0 send_seq=6842 receive_seq=6842 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998652 coil_temp=17.5 refs=0 mcu_temp=20.73 supply_voltage=3.012 th0: temp=43.6 th1: temp=44.4 th2: temp=46.6 th3: temp=45.9 sysload=0.05 cputime=232.362 memavail=7397264 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 2625.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953151 bytes_read=2493984 bytes_retransmit=9 bytes_invalid=0 send_seq=349827 receive_seq=349827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015942 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16642 bytes_read=53272 bytes_retransmit=0 bytes_invalid=0 send_seq=2745 receive_seq=2745 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997471 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=110208 bytes_read=3501530 bytes_retransmit=9 bytes_invalid=0 send_seq=14945 receive_seq=14945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997627 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52556 bytes_read=1057127 bytes_retransmit=9 bytes_invalid=0 send_seq=6798 receive_seq=6798 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16881 bytes_read=667196 bytes_retransmit=9 bytes_invalid=0 send_seq=2757 receive_seq=2757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17395 bytes_read=52241 bytes_retransmit=9 bytes_invalid=0 send_seq=2746 receive_seq=2746 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999437 Octopus_Pro_H723_V1.1: temp=30.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65967 bytes_read=1152449 bytes_retransmit=0 bytes_invalid=0 send_seq=6843 receive_seq=6843 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998647 coil_temp=17.5 refs=0 mcu_temp=20.73 supply_voltage=3.012 th0: temp=43.7 th1: temp=44.5 th2: temp=46.6 th3: temp=45.8 sysload=0.05 cputime=232.394 memavail=7397172 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2626.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953163 bytes_read=2494117 bytes_retransmit=9 bytes_invalid=0 send_seq=349829 receive_seq=349829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015933 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16654 bytes_read=53304 bytes_retransmit=0 bytes_invalid=0 send_seq=2747 receive_seq=2747 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997382 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=110220 bytes_read=3501646 bytes_retransmit=9 bytes_invalid=0 send_seq=14947 receive_seq=14947 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997641 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52568 bytes_read=1057243 bytes_retransmit=9 bytes_invalid=0 send_seq=6800 receive_seq=6800 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997513 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16893 bytes_read=667446 bytes_retransmit=9 bytes_invalid=0 send_seq=2759 receive_seq=2759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17407 bytes_read=52284 bytes_retransmit=9 bytes_invalid=0 send_seq=2748 receive_seq=2748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999438 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65979 bytes_read=1152821 bytes_retransmit=0 bytes_invalid=0 send_seq=6845 receive_seq=6845 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998662 coil_temp=17.5 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=43.6 th1: temp=44.3 th2: temp=46.5 th3: temp=45.8 sysload=0.05 cputime=232.427 memavail=7397300 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2627.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953169 bytes_read=2494220 bytes_retransmit=9 bytes_invalid=0 send_seq=349830 receive_seq=349830 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015932 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16660 bytes_read=53333 bytes_retransmit=0 bytes_invalid=0 send_seq=2748 receive_seq=2748 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997334 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=110226 bytes_read=3501774 bytes_retransmit=9 bytes_invalid=0 send_seq=14948 receive_seq=14948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997755 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52574 bytes_read=1057371 bytes_retransmit=9 bytes_invalid=0 send_seq=6801 receive_seq=6801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997530 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16899 bytes_read=667740 bytes_retransmit=9 bytes_invalid=0 send_seq=2760 receive_seq=2760 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17413 bytes_read=52300 bytes_retransmit=9 bytes_invalid=0 send_seq=2749 receive_seq=2749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999440 Octopus_Pro_H723_V1.1: temp=30.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65985 bytes_read=1153177 bytes_retransmit=0 bytes_invalid=0 send_seq=6846 receive_seq=6846 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998654 coil_temp=17.5 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=43.7 th1: temp=44.4 th2: temp=46.4 th3: temp=45.7 sysload=0.05 cputime=232.461 memavail=7397300 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 2628.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953175 bytes_read=2494352 bytes_retransmit=9 bytes_invalid=0 send_seq=349831 receive_seq=349831 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015927 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16666 bytes_read=53349 bytes_retransmit=0 bytes_invalid=0 send_seq=2749 receive_seq=2749 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997295 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110232 bytes_read=3501888 bytes_retransmit=9 bytes_invalid=0 send_seq=14949 receive_seq=14949 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997723 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52580 bytes_read=1057471 bytes_retransmit=9 bytes_invalid=0 send_seq=6802 receive_seq=6802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997534 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16905 bytes_read=667974 bytes_retransmit=9 bytes_invalid=0 send_seq=2761 receive_seq=2761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17419 bytes_read=52316 bytes_retransmit=9 bytes_invalid=0 send_seq=2750 receive_seq=2750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65991 bytes_read=1153533 bytes_retransmit=0 bytes_invalid=0 send_seq=6847 receive_seq=6847 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998649 coil_temp=17.5 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=43.6 th1: temp=44.4 th2: temp=46.4 th3: temp=45.7 sysload=0.05 cputime=232.492 memavail=7397300 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 2629.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953181 bytes_read=2494452 bytes_retransmit=9 bytes_invalid=0 send_seq=349832 receive_seq=349832 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015925 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16672 bytes_read=53365 bytes_retransmit=0 bytes_invalid=0 send_seq=2750 receive_seq=2750 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997259 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110238 bytes_read=3501988 bytes_retransmit=9 bytes_invalid=0 send_seq=14950 receive_seq=14950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997718 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52586 bytes_read=1057571 bytes_retransmit=9 bytes_invalid=0 send_seq=6803 receive_seq=6803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997535 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=16911 bytes_read=668208 bytes_retransmit=9 bytes_invalid=0 send_seq=2762 receive_seq=2762 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997634 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17425 bytes_read=52332 bytes_retransmit=9 bytes_invalid=0 send_seq=2751 receive_seq=2751 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=65997 bytes_read=1153889 bytes_retransmit=0 bytes_invalid=0 send_seq=6848 receive_seq=6848 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998642 coil_temp=17.5 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=43.6 th1: temp=44.4 th2: temp=46.4 th3: temp=45.7 sysload=0.05 cputime=232.523 memavail=7397300 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 2630.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953187 bytes_read=2494553 bytes_retransmit=9 bytes_invalid=0 send_seq=349833 receive_seq=349833 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015921 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16678 bytes_read=53381 bytes_retransmit=0 bytes_invalid=0 send_seq=2751 receive_seq=2751 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997225 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110244 bytes_read=3502116 bytes_retransmit=9 bytes_invalid=0 send_seq=14951 receive_seq=14951 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997699 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52592 bytes_read=1057713 bytes_retransmit=9 bytes_invalid=0 send_seq=6804 receive_seq=6804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997540 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=16917 bytes_read=668517 bytes_retransmit=9 bytes_invalid=0 send_seq=2763 receive_seq=2763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997629 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17431 bytes_read=52348 bytes_retransmit=9 bytes_invalid=0 send_seq=2752 receive_seq=2752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999436 Octopus_Pro_H723_V1.1: temp=30.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=66003 bytes_read=1154245 bytes_retransmit=0 bytes_invalid=0 send_seq=6849 receive_seq=6849 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998642 coil_temp=17.5 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=43.6 th1: temp=44.3 th2: temp=46.5 th3: temp=45.6 sysload=0.05 cputime=232.555 memavail=7397344 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 2631.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953193 bytes_read=2494699 bytes_retransmit=9 bytes_invalid=0 send_seq=349834 receive_seq=349834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015918 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16684 bytes_read=53397 bytes_retransmit=0 bytes_invalid=0 send_seq=2752 receive_seq=2752 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997204 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110250 bytes_read=3502216 bytes_retransmit=9 bytes_invalid=0 send_seq=14952 receive_seq=14952 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997683 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52598 bytes_read=1057813 bytes_retransmit=9 bytes_invalid=0 send_seq=6805 receive_seq=6805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=16923 bytes_read=668751 bytes_retransmit=9 bytes_invalid=0 send_seq=2764 receive_seq=2764 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17437 bytes_read=52375 bytes_retransmit=9 bytes_invalid=0 send_seq=2753 receive_seq=2753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=30.3 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=66009 bytes_read=1154601 bytes_retransmit=0 bytes_invalid=0 send_seq=6850 receive_seq=6850 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998642 coil_temp=17.5 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.2 th2: temp=46.3 th3: temp=45.7 sysload=0.05 cputime=232.589 memavail=7391812 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 2632.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=19953199 bytes_read=2494802 bytes_retransmit=9 bytes_invalid=0 send_seq=349835 receive_seq=349835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015922 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=16690 bytes_read=53426 bytes_retransmit=0 bytes_invalid=0 send_seq=2753 receive_seq=2753 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997203 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=110256 bytes_read=3502316 bytes_retransmit=9 bytes_invalid=0 send_seq=14953 receive_seq=14953 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997673 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=52604 bytes_read=1057913 bytes_retransmit=9 bytes_invalid=0 send_seq=6806 receive_seq=6806 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997541 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=16929 bytes_read=668985 bytes_retransmit=9 bytes_invalid=0 send_seq=2765 receive_seq=2765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997632 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=17443 bytes_read=52391 bytes_retransmit=9 bytes_invalid=0 send_seq=2754 receive_seq=2754 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=30.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=66015 bytes_read=1154957 bytes_retransmit=0 bytes_invalid=0 send_seq=6851 receive_seq=6851 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998664 coil_temp=17.5 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.3 th2: temp=46.3 th3: temp=45.6 sysload=0.04 cputime=232.620 memavail=7397944 print_time=2595.199 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Extruder extruder already active
Extruder 'extruder' now syncing with 'extruder'
Extruder 'extruder1' now syncing with 'extruder1'
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 3375.0: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000002 mcu_task_stddev=0.000001 bytes_write=19959352 bytes_read=2581597 bytes_retransmit=9 bytes_invalid=0 send_seq=350664 receive_seq=350664 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015007 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=21214 bytes_read=67351 bytes_retransmit=0 bytes_invalid=0 send_seq=3507 receive_seq=3507 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999214 adj=49997314 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114780 bytes_read=3585381 bytes_retransmit=9 bytes_invalid=0 send_seq=15707 receive_seq=15707 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997832 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=57128 bytes_read=1140966 bytes_retransmit=9 bytes_invalid=0 send_seq=7560 receive_seq=7560 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000033 adj=63997614 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21453 bytes_read=859226 bytes_retransmit=9 bytes_invalid=0 send_seq=3519 receive_seq=3519 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999513 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=21967 bytes_read=66038 bytes_retransmit=9 bytes_invalid=0 send_seq=3508 receive_seq=3508 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999466 Octopus_Pro_H723_V1.1: temp=37.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=70539 bytes_read=1418585 bytes_retransmit=0 bytes_invalid=0 send_seq=7605 receive_seq=7605 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998694 coil_temp=17.9 refs=0 mcu_temp=21.08 supply_voltage=3.012 th0: temp=36.6 th1: temp=37.1 th2: temp=39.0 th3: temp=38.5 sysload=0.10 cputime=256.142 memavail=7398608 print_time=3397.892 buffer_time=0.378 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 3376.0: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000002 mcu_task_stddev=0.000001 bytes_write=19962090 bytes_read=2583709 bytes_retransmit=9 bytes_invalid=0 send_seq=350792 receive_seq=350792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015004 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=21220 bytes_read=67367 bytes_retransmit=0 bytes_invalid=0 send_seq=3508 receive_seq=3508 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997320 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114786 bytes_read=3585481 bytes_retransmit=9 bytes_invalid=0 send_seq=15708 receive_seq=15708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997802 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=57134 bytes_read=1141080 bytes_retransmit=9 bytes_invalid=0 send_seq=7561 receive_seq=7561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000033 adj=63997622 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=21487 bytes_read=859481 bytes_retransmit=9 bytes_invalid=0 send_seq=3522 receive_seq=3522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999513 adj=47997679 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=21973 bytes_read=66054 bytes_retransmit=9 bytes_invalid=0 send_seq=3509 receive_seq=3509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999469 Octopus_Pro_H723_V1.1: temp=37.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=70545 bytes_read=1418941 bytes_retransmit=0 bytes_invalid=0 send_seq=7606 receive_seq=7606 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998691 coil_temp=17.9 refs=0 mcu_temp=21.07 supply_voltage=3.012 th0: temp=37.6 th1: temp=37.4 th2: temp=39.7 th3: temp=39.3 sysload=0.10 cputime=256.224 memavail=7398120 print_time=3398.724 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 3377.0: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000002 mcu_task_stddev=0.000001 bytes_write=19963274 bytes_read=2584471 bytes_retransmit=9 bytes_invalid=0 send_seq=350846 receive_seq=350846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400014999 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=21226 bytes_read=67383 bytes_retransmit=0 bytes_invalid=0 send_seq=3509 receive_seq=3509 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997361 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114792 bytes_read=3585609 bytes_retransmit=9 bytes_invalid=0 send_seq=15709 receive_seq=15709 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997801 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=57140 bytes_read=1141194 bytes_retransmit=9 bytes_invalid=0 send_seq=7562 receive_seq=7562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000033 adj=63997630 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=21493 bytes_read=859727 bytes_retransmit=9 bytes_invalid=0 send_seq=3523 receive_seq=3523 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999512 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=21979 bytes_read=66081 bytes_retransmit=9 bytes_invalid=0 send_seq=3510 receive_seq=3510 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999470 Octopus_Pro_H723_V1.1: temp=36.9 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=70551 bytes_read=1419297 bytes_retransmit=0 bytes_invalid=0 send_seq=7607 receive_seq=7607 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998694 coil_temp=17.9 refs=0 mcu_temp=21.05 supply_voltage=3.012 th0: temp=37.5 th1: temp=37.6 th2: temp=39.8 th3: temp=38.8 sysload=0.10 cputime=256.284 memavail=7399860 print_time=3399.724 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 3378.0: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000002 mcu_task_stddev=0.000001 bytes_write=19964463 bytes_read=2585267 bytes_retransmit=9 bytes_invalid=0 send_seq=350901 receive_seq=350901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400014991 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=21232 bytes_read=67399 bytes_retransmit=0 bytes_invalid=0 send_seq=3510 receive_seq=3510 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997360 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114798 bytes_read=3585709 bytes_retransmit=9 bytes_invalid=0 send_seq=15710 receive_seq=15710 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997793 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=57146 bytes_read=1141308 bytes_retransmit=9 bytes_invalid=0 send_seq=7563 receive_seq=7563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997636 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=21499 bytes_read=859973 bytes_retransmit=9 bytes_invalid=0 send_seq=3524 receive_seq=3524 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=21985 bytes_read=66097 bytes_retransmit=9 bytes_invalid=0 send_seq=3511 receive_seq=3511 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999470 Octopus_Pro_H723_V1.1: temp=36.5 EBB42_Gen2_v1.0_T0: temp=31.2 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=70557 bytes_read=1419653 bytes_retransmit=0 bytes_invalid=0 send_seq=7608 receive_seq=7608 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998694 coil_temp=17.9 refs=0 mcu_temp=21.05 supply_voltage=3.012 th0: temp=37.8 th1: temp=37.6 th2: temp=39.9 th3: temp=39.1 sysload=0.09 cputime=256.343 memavail=7399860 print_time=3400.724 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 3379.0: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000002 mcu_task_stddev=0.000001 bytes_write=19965664 bytes_read=2586053 bytes_retransmit=9 bytes_invalid=0 send_seq=350957 receive_seq=350957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400014991 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=21238 bytes_read=67415 bytes_retransmit=0 bytes_invalid=0 send_seq=3511 receive_seq=3511 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997369 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114804 bytes_read=3585823 bytes_retransmit=9 bytes_invalid=0 send_seq=15711 receive_seq=15711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997995 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=57152 bytes_read=1141408 bytes_retransmit=9 bytes_invalid=0 send_seq=7564 receive_seq=7564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997653 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=21505 bytes_read=860191 bytes_retransmit=9 bytes_invalid=0 send_seq=3525 receive_seq=3525 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997702 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=21991 bytes_read=66113 bytes_retransmit=9 bytes_invalid=0 send_seq=3512 receive_seq=3512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999471 Octopus_Pro_H723_V1.1: temp=36.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=70563 bytes_read=1420009 bytes_retransmit=0 bytes_invalid=0 send_seq=7609 receive_seq=7609 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998699 coil_temp=17.9 refs=0 mcu_temp=21.05 supply_voltage=3.012 th0: temp=37.4 th1: temp=37.7 th2: temp=40.1 th3: temp=39.2 sysload=0.09 cputime=256.401 memavail=7399860 print_time=3401.724 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 3380.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000006 mcu_task_stddev=0.000008 bytes_write=19966853 bytes_read=2586836 bytes_retransmit=9 bytes_invalid=0 send_seq=351012 receive_seq=351012 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400014982 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21244 bytes_read=67444 bytes_retransmit=0 bytes_invalid=0 send_seq=3512 receive_seq=3512 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999215 adj=49997366 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114810 bytes_read=3585951 bytes_retransmit=9 bytes_invalid=0 send_seq=15712 receive_seq=15712 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997933 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=57158 bytes_read=1141536 bytes_retransmit=9 bytes_invalid=0 send_seq=7565 receive_seq=7565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000033 adj=63997645 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=21511 bytes_read=860437 bytes_retransmit=9 bytes_invalid=0 send_seq=3526 receive_seq=3526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997705 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=21997 bytes_read=66129 bytes_retransmit=9 bytes_invalid=0 send_seq=3513 receive_seq=3513 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999469 Octopus_Pro_H723_V1.1: temp=36.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=70569 bytes_read=1420365 bytes_retransmit=0 bytes_invalid=0 send_seq=7610 receive_seq=7610 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998710 coil_temp=17.9 refs=0 mcu_temp=21.05 supply_voltage=3.012 th0: temp=37.9 th1: temp=37.8 th2: temp=40.4 th3: temp=39.3 sysload=0.09 cputime=256.460 memavail=7399860 print_time=3402.724 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 3381.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000006 mcu_task_stddev=0.000008 bytes_write=19968040 bytes_read=2587630 bytes_retransmit=9 bytes_invalid=0 send_seq=351067 receive_seq=351067 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400014975 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21250 bytes_read=67460 bytes_retransmit=0 bytes_invalid=0 send_seq=3513 receive_seq=3513 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999215 adj=49997369 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114816 bytes_read=3586051 bytes_retransmit=9 bytes_invalid=0 send_seq=15713 receive_seq=15713 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997898 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=57164 bytes_read=1141650 bytes_retransmit=9 bytes_invalid=0 send_seq=7566 receive_seq=7566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000033 adj=63997683 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=21517 bytes_read=860698 bytes_retransmit=9 bytes_invalid=0 send_seq=3527 receive_seq=3527 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997722 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22003 bytes_read=66145 bytes_retransmit=9 bytes_invalid=0 send_seq=3514 receive_seq=3514 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999475 Octopus_Pro_H723_V1.1: temp=35.8 EBB42_Gen2_v1.0_T0: temp=31.1 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=70575 bytes_read=1420721 bytes_retransmit=0 bytes_invalid=0 send_seq=7611 receive_seq=7611 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998726 coil_temp=17.9 refs=0 mcu_temp=21.04 supply_voltage=3.012 th0: temp=38.5 th1: temp=38.0 th2: temp=40.4 th3: temp=39.5 sysload=0.09 cputime=256.520 memavail=7399860 print_time=3403.724 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Stats 3382.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000006 mcu_task_stddev=0.000008 bytes_write=19972319 bytes_read=2588898 bytes_retransmit=9 bytes_invalid=0 send_seq=351190 receive_seq=351190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=0 freq=400014972 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21256 bytes_read=67476 bytes_retransmit=0 bytes_invalid=0 send_seq=3514 receive_seq=3514 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999214 adj=49997370 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114822 bytes_read=3586151 bytes_retransmit=9 bytes_invalid=0 send_seq=15714 receive_seq=15714 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=0 freq=64000223 adj=63997866 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=57170 bytes_read=1141750 bytes_retransmit=9 bytes_invalid=0 send_seq=7567 receive_seq=7567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000033 adj=63997684 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=21523 bytes_read=860928 bytes_retransmit=9 bytes_invalid=0 send_seq=3528 receive_seq=3528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999511 adj=47997725 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22009 bytes_read=66172 bytes_retransmit=9 bytes_invalid=0 send_seq=3515 receive_seq=3515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999475 Octopus_Pro_H723_V1.1: temp=35.8 EBB42_Gen2_v1.0_T0: temp=31.2 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=70581 bytes_read=1421077 bytes_retransmit=0 bytes_invalid=0 send_seq=7612 receive_seq=7612 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998727 coil_temp=17.9 refs=0 mcu_temp=21.03 supply_voltage=3.012 th0: temp=38.4 th1: temp=38.1 th2: temp=40.7 th3: temp=39.5 sysload=0.09 cputime=256.622 memavail=7399860 print_time=3405.268 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3383.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000006 mcu_task_stddev=0.000008 bytes_write=19973232 bytes_read=2590052 bytes_retransmit=9 bytes_invalid=0 send_seq=351258 receive_seq=351258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400014996 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21262 bytes_read=67492 bytes_retransmit=0 bytes_invalid=0 send_seq=3515 receive_seq=3515 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999214 adj=49997360 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115298 bytes_read=3586982 bytes_retransmit=9 bytes_invalid=0 send_seq=15752 receive_seq=15752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997966 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=57176 bytes_read=1141878 bytes_retransmit=9 bytes_invalid=0 send_seq=7568 receive_seq=7568 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000033 adj=63997674 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=21529 bytes_read=861192 bytes_retransmit=9 bytes_invalid=0 send_seq=3529 receive_seq=3529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999510 adj=47997726 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22015 bytes_read=66188 bytes_retransmit=9 bytes_invalid=0 send_seq=3516 receive_seq=3516 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999472 Octopus_Pro_H723_V1.1: temp=35.5 EBB42_Gen2_v1.0_T0: temp=31.2 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=70587 bytes_read=1421433 bytes_retransmit=0 bytes_invalid=0 send_seq=7613 receive_seq=7613 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998718 coil_temp=17.9 refs=0 mcu_temp=21.02 supply_voltage=3.012 th0: temp=38.3 th1: temp=38.2 th2: temp=41.3 th3: temp=39.9 sysload=0.09 cputime=256.684 memavail=7399860 print_time=3405.718 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 3384.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000006 mcu_task_stddev=0.000008 bytes_write=19975393 bytes_read=2593147 bytes_retransmit=9 bytes_invalid=0 send_seq=351434 receive_seq=351434 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400014986 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21268 bytes_read=67508 bytes_retransmit=0 bytes_invalid=0 send_seq=3516 receive_seq=3516 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997301 toolboard_t0: mcu_awake=0.012 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=116924 bytes_read=3589634 bytes_retransmit=9 bytes_invalid=0 send_seq=15888 receive_seq=15888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997871 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=57182 bytes_read=1141978 bytes_retransmit=9 bytes_invalid=0 send_seq=7569 receive_seq=7569 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997610 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=21535 bytes_read=861456 bytes_retransmit=9 bytes_invalid=0 send_seq=3530 receive_seq=3530 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999510 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22021 bytes_read=66204 bytes_retransmit=9 bytes_invalid=0 send_seq=3517 receive_seq=3517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999462 Octopus_Pro_H723_V1.1: temp=35.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=70593 bytes_read=1421789 bytes_retransmit=0 bytes_invalid=0 send_seq=7614 receive_seq=7614 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998676 coil_temp=17.9 refs=0 mcu_temp=21.03 supply_voltage=3.012 th0: temp=38.5 th1: temp=38.7 th2: temp=41.0 th3: temp=39.8 sysload=0.09 cputime=256.786 memavail=7399860 print_time=3406.718 buffer_time=0.000 print_stall=0 extruder: target=0 temp=20.0 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 3385.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=19977559 bytes_read=2596220 bytes_retransmit=9 bytes_invalid=0 send_seq=351611 receive_seq=351611 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015022 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21274 bytes_read=67537 bytes_retransmit=0 bytes_invalid=0 send_seq=3517 receive_seq=3517 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997324 toolboard_t0: mcu_awake=0.012 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=118538 bytes_read=3592266 bytes_retransmit=9 bytes_invalid=0 send_seq=16023 receive_seq=16023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997852 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=57188 bytes_read=1142078 bytes_retransmit=9 bytes_invalid=0 send_seq=7570 receive_seq=7570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997766 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=21541 bytes_read=861690 bytes_retransmit=9 bytes_invalid=0 send_seq=3531 receive_seq=3531 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999510 adj=47997701 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22027 bytes_read=66220 bytes_retransmit=9 bytes_invalid=0 send_seq=3518 receive_seq=3518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999469 Octopus_Pro_H723_V1.1: temp=35.1 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=70599 bytes_read=1422145 bytes_retransmit=0 bytes_invalid=0 send_seq=7615 receive_seq=7615 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998719 coil_temp=17.9 refs=0 mcu_temp=21.03 supply_voltage=3.012 th0: temp=38.6 th1: temp=39.2 th2: temp=40.9 th3: temp=40.1 sysload=0.09 cputime=256.888 memavail=7399860 print_time=3407.718 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 3386.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=19979725 bytes_read=2599277 bytes_retransmit=9 bytes_invalid=0 send_seq=351788 receive_seq=351788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015019 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21280 bytes_read=67553 bytes_retransmit=0 bytes_invalid=0 send_seq=3518 receive_seq=3518 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997244 toolboard_t0: mcu_awake=0.012 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=120140 bytes_read=3594935 bytes_retransmit=9 bytes_invalid=0 send_seq=16157 receive_seq=16157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997713 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=57194 bytes_read=1142220 bytes_retransmit=9 bytes_invalid=0 send_seq=7571 receive_seq=7571 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997649 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21547 bytes_read=861969 bytes_retransmit=9 bytes_invalid=0 send_seq=3532 receive_seq=3532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999510 adj=47997632 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22033 bytes_read=66236 bytes_retransmit=9 bytes_invalid=0 send_seq=3519 receive_seq=3519 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999450 Octopus_Pro_H723_V1.1: temp=35.1 EBB42_Gen2_v1.0_T0: temp=31.1 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=70605 bytes_read=1422501 bytes_retransmit=0 bytes_invalid=0 send_seq=7616 receive_seq=7616 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998684 coil_temp=17.9 refs=0 mcu_temp=21.02 supply_voltage=3.012 th0: temp=39.0 th1: temp=38.8 th2: temp=41.4 th3: temp=40.2 sysload=0.09 cputime=256.991 memavail=7399932 print_time=3408.718 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 3387.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=19981580 bytes_read=2601832 bytes_retransmit=9 bytes_invalid=0 send_seq=351937 receive_seq=351937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=0 freq=400015012 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21286 bytes_read=67569 bytes_retransmit=0 bytes_invalid=0 send_seq=3519 receive_seq=3519 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997263 toolboard_t0: mcu_awake=0.012 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=121407 bytes_read=3597041 bytes_retransmit=9 bytes_invalid=0 send_seq=16264 receive_seq=16264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=0 freq=64000223 adj=63997805 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=57200 bytes_read=1142320 bytes_retransmit=9 bytes_invalid=0 send_seq=7572 receive_seq=7572 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997671 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21553 bytes_read=862233 bytes_retransmit=9 bytes_invalid=0 send_seq=3533 receive_seq=3533 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22039 bytes_read=66263 bytes_retransmit=9 bytes_invalid=0 send_seq=3520 receive_seq=3520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999469 Octopus_Pro_H723_V1.1: temp=34.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=70611 bytes_read=1422857 bytes_retransmit=0 bytes_invalid=0 send_seq=7617 receive_seq=7617 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998685 coil_temp=17.9 refs=0 mcu_temp=21.01 supply_voltage=3.012 th0: temp=38.8 th1: temp=38.7 th2: temp=41.9 th3: temp=40.5 sysload=0.09 cputime=257.088 memavail=7399932 print_time=3409.874 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 3388.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=19982935 bytes_read=2603427 bytes_retransmit=9 bytes_invalid=0 send_seq=352037 receive_seq=352037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015001 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21292 bytes_read=67585 bytes_retransmit=0 bytes_invalid=0 send_seq=3520 receive_seq=3520 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997297 toolboard_t0: mcu_awake=0.012 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=121848 bytes_read=3597784 bytes_retransmit=9 bytes_invalid=0 send_seq=16300 receive_seq=16300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997864 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=57508 bytes_read=1142871 bytes_retransmit=9 bytes_invalid=0 send_seq=7596 receive_seq=7596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997679 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21559 bytes_read=862449 bytes_retransmit=9 bytes_invalid=0 send_seq=3534 receive_seq=3534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997798 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22045 bytes_read=66279 bytes_retransmit=9 bytes_invalid=0 send_seq=3521 receive_seq=3521 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999470 Octopus_Pro_H723_V1.1: temp=34.7 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=70617 bytes_read=1423213 bytes_retransmit=0 bytes_invalid=0 send_seq=7618 receive_seq=7618 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998697 coil_temp=17.9 refs=0 mcu_temp=20.99 supply_voltage=3.012 th0: temp=38.9 th1: temp=38.6 th2: temp=41.8 th3: temp=40.7 sysload=0.08 cputime=257.165 memavail=7399932 print_time=3410.716 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 3389.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=19985096 bytes_read=2606493 bytes_retransmit=9 bytes_invalid=0 send_seq=352213 receive_seq=352213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015189 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21298 bytes_read=67601 bytes_retransmit=0 bytes_invalid=0 send_seq=3521 receive_seq=3521 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997327 toolboard_t0: mcu_awake=0.053 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=121854 bytes_read=3597928 bytes_retransmit=9 bytes_invalid=0 send_seq=16301 receive_seq=16301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997838 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=59122 bytes_read=1145531 bytes_retransmit=9 bytes_invalid=0 send_seq=7731 receive_seq=7731 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997690 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21565 bytes_read=862728 bytes_retransmit=9 bytes_invalid=0 send_seq=3535 receive_seq=3535 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997809 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22051 bytes_read=66295 bytes_retransmit=9 bytes_invalid=0 send_seq=3522 receive_seq=3522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999476 Octopus_Pro_H723_V1.1: temp=34.7 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=70623 bytes_read=1423569 bytes_retransmit=0 bytes_invalid=0 send_seq=7619 receive_seq=7619 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998713 coil_temp=17.9 refs=0 mcu_temp=20.99 supply_voltage=3.012 th0: temp=39.3 th1: temp=39.2 th2: temp=42.4 th3: temp=40.8 sysload=0.08 cputime=257.270 memavail=7399712 print_time=3411.716 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 3390.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000002 mcu_task_stddev=0.000003 bytes_write=19987259 bytes_read=2609585 bytes_retransmit=9 bytes_invalid=0 send_seq=352388 receive_seq=352388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015168 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21304 bytes_read=67630 bytes_retransmit=0 bytes_invalid=0 send_seq=3522 receive_seq=3522 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49996961 toolboard_t0: mcu_awake=0.053 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=121860 bytes_read=3598028 bytes_retransmit=9 bytes_invalid=0 send_seq=16302 receive_seq=16302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997328 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=60736 bytes_read=1148177 bytes_retransmit=9 bytes_invalid=0 send_seq=7866 receive_seq=7866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997252 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21571 bytes_read=862977 bytes_retransmit=9 bytes_invalid=0 send_seq=3536 receive_seq=3536 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997421 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22057 bytes_read=66311 bytes_retransmit=9 bytes_invalid=0 send_seq=3523 receive_seq=3523 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999383 Octopus_Pro_H723_V1.1: temp=34.3 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=70629 bytes_read=1423925 bytes_retransmit=0 bytes_invalid=0 send_seq=7620 receive_seq=7620 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998476 coil_temp=17.9 refs=0 mcu_temp=20.99 supply_voltage=3.012 th0: temp=39.3 th1: temp=38.7 th2: temp=42.4 th3: temp=40.9 sysload=0.08 cputime=257.373 memavail=7399712 print_time=3412.716 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3391.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000002 mcu_task_stddev=0.000003 bytes_write=19989420 bytes_read=2612651 bytes_retransmit=9 bytes_invalid=0 send_seq=352564 receive_seq=352564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015354 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21310 bytes_read=67646 bytes_retransmit=0 bytes_invalid=0 send_seq=3523 receive_seq=3523 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997094 toolboard_t0: mcu_awake=0.053 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=121866 bytes_read=3598128 bytes_retransmit=9 bytes_invalid=0 send_seq=16303 receive_seq=16303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997481 toolboard_t1: mcu_awake=0.041 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=62362 bytes_read=1150830 bytes_retransmit=9 bytes_invalid=0 send_seq=8002 receive_seq=8002 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997467 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21577 bytes_read=863226 bytes_retransmit=9 bytes_invalid=0 send_seq=3537 receive_seq=3537 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997523 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22063 bytes_read=66327 bytes_retransmit=9 bytes_invalid=0 send_seq=3524 receive_seq=3524 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999411 Octopus_Pro_H723_V1.1: temp=34.5 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=70635 bytes_read=1424281 bytes_retransmit=0 bytes_invalid=0 send_seq=7621 receive_seq=7621 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998557 coil_temp=17.9 refs=0 mcu_temp=20.99 supply_voltage=3.012 th0: temp=39.4 th1: temp=39.2 th2: temp=42.5 th3: temp=41.1 sysload=0.08 cputime=257.492 memavail=7400600 print_time=3413.716 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 3392.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000002 mcu_task_stddev=0.000003 bytes_write=19991494 bytes_read=2615411 bytes_retransmit=9 bytes_invalid=0 send_seq=352728 receive_seq=352728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015384 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21316 bytes_read=67662 bytes_retransmit=0 bytes_invalid=0 send_seq=3524 receive_seq=3524 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999215 adj=49996802 toolboard_t0: mcu_awake=0.053 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=121872 bytes_read=3598256 bytes_retransmit=9 bytes_invalid=0 send_seq=16304 receive_seq=16304 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997081 toolboard_t1: mcu_awake=0.041 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=63773 bytes_read=1153206 bytes_retransmit=9 bytes_invalid=0 send_seq=8121 receive_seq=8121 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=0 freq=64000047 adj=63997019 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21583 bytes_read=863505 bytes_retransmit=9 bytes_invalid=0 send_seq=3538 receive_seq=3538 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997204 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22069 bytes_read=66354 bytes_retransmit=9 bytes_invalid=0 send_seq=3525 receive_seq=3525 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999347 Octopus_Pro_H723_V1.1: temp=34.4 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=70641 bytes_read=1424637 bytes_retransmit=0 bytes_invalid=0 send_seq=7622 receive_seq=7622 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998364 coil_temp=17.9 refs=0 mcu_temp=20.98 supply_voltage=3.012 th0: temp=39.2 th1: temp=39.2 th2: temp=43.3 th3: temp=41.4 sysload=0.08 cputime=257.591 memavail=7400600 print_time=3414.819 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 3393.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000002 mcu_task_stddev=0.000003 bytes_write=19992882 bytes_read=2616568 bytes_retransmit=9 bytes_invalid=0 send_seq=352805 receive_seq=352805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015373 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21322 bytes_read=67678 bytes_retransmit=0 bytes_invalid=0 send_seq=3525 receive_seq=3525 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999215 adj=49996908 toolboard_t0: mcu_awake=0.053 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=121878 bytes_read=3598356 bytes_retransmit=9 bytes_invalid=0 send_seq=16305 receive_seq=16305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997240 toolboard_t1: mcu_awake=0.041 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=64202 bytes_read=1153944 bytes_retransmit=9 bytes_invalid=0 send_seq=8156 receive_seq=8156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997088 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21589 bytes_read=863754 bytes_retransmit=9 bytes_invalid=0 send_seq=3539 receive_seq=3539 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997275 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22075 bytes_read=66370 bytes_retransmit=9 bytes_invalid=0 send_seq=3526 receive_seq=3526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999362 Octopus_Pro_H723_V1.1: temp=34.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=70647 bytes_read=1424993 bytes_retransmit=0 bytes_invalid=0 send_seq=7623 receive_seq=7623 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998413 coil_temp=17.9 refs=0 mcu_temp=20.99 supply_voltage=3.012 th0: temp=39.8 th1: temp=39.5 th2: temp=43.1 th3: temp=41.7 sysload=0.07 cputime=257.668 memavail=7400600 print_time=3415.936 buffer_time=0.412 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
RatOS:: Homing Z
Stats 3394.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000002 mcu_task_stddev=0.000003 bytes_write=19994363 bytes_read=2617828 bytes_retransmit=9 bytes_invalid=0 send_seq=352883 receive_seq=352883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015393 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21328 bytes_read=67694 bytes_retransmit=0 bytes_invalid=0 send_seq=3526 receive_seq=3526 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997029 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=121884 bytes_read=3598470 bytes_retransmit=9 bytes_invalid=0 send_seq=16306 receive_seq=16306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997380 toolboard_t1: mcu_awake=0.041 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=64208 bytes_read=1154044 bytes_retransmit=9 bytes_invalid=0 send_seq=8157 receive_seq=8157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997234 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21595 bytes_read=863988 bytes_retransmit=9 bytes_invalid=0 send_seq=3540 receive_seq=3540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997399 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22081 bytes_read=66386 bytes_retransmit=9 bytes_invalid=0 send_seq=3527 receive_seq=3527 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999390 Octopus_Pro_H723_V1.1: temp=34.1 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=71176 bytes_read=1426209 bytes_retransmit=0 bytes_invalid=0 send_seq=7667 receive_seq=7667 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998498 coil_temp=17.9 refs=0 mcu_temp=20.99 supply_voltage=3.012 th0: temp=39.8 th1: temp=39.6 th2: temp=42.8 th3: temp=41.7 sysload=0.07 cputime=257.745 memavail=7400600 print_time=3416.697 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 3395.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=19996856 bytes_read=2620901 bytes_retransmit=9 bytes_invalid=0 send_seq=353060 receive_seq=353060 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015366 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21334 bytes_read=67710 bytes_retransmit=0 bytes_invalid=0 send_seq=3527 receive_seq=3527 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997076 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=121890 bytes_read=3598598 bytes_retransmit=9 bytes_invalid=0 send_seq=16307 receive_seq=16307 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997418 toolboard_t1: mcu_awake=0.041 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=64214 bytes_read=1154172 bytes_retransmit=9 bytes_invalid=0 send_seq=8158 receive_seq=8158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997257 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21601 bytes_read=864267 bytes_retransmit=9 bytes_invalid=0 send_seq=3541 receive_seq=3541 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997405 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22087 bytes_read=66402 bytes_retransmit=9 bytes_invalid=0 send_seq=3528 receive_seq=3528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999399 Octopus_Pro_H723_V1.1: temp=33.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=72790 bytes_read=1429111 bytes_retransmit=0 bytes_invalid=0 send_seq=7802 receive_seq=7802 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998517 coil_temp=17.9 refs=0 mcu_temp=21.00 supply_voltage=3.012 th0: temp=40.0 th1: temp=39.5 th2: temp=43.3 th3: temp=41.8 sysload=0.07 cputime=257.847 memavail=7400600 print_time=3417.697 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 3396.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=19999342 bytes_read=2624001 bytes_retransmit=9 bytes_invalid=0 send_seq=353237 receive_seq=353237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015331 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21340 bytes_read=67739 bytes_retransmit=0 bytes_invalid=0 send_seq=3528 receive_seq=3528 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997180 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=121896 bytes_read=3598698 bytes_retransmit=9 bytes_invalid=0 send_seq=16308 receive_seq=16308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997558 toolboard_t1: mcu_awake=0.024 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=64220 bytes_read=1154287 bytes_retransmit=9 bytes_invalid=0 send_seq=8159 receive_seq=8159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997388 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=21607 bytes_read=864531 bytes_retransmit=9 bytes_invalid=0 send_seq=3542 receive_seq=3542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999514 adj=47997529 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22093 bytes_read=66418 bytes_retransmit=9 bytes_invalid=0 send_seq=3529 receive_seq=3529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999424 Octopus_Pro_H723_V1.1: temp=33.9 EBB42_Gen2_v1.0_T0: temp=31.1 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=74416 bytes_read=1432004 bytes_retransmit=0 bytes_invalid=0 send_seq=7938 receive_seq=7938 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998675 coil_temp=17.9 refs=0 mcu_temp=21.00 supply_voltage=3.012 th0: temp=40.0 th1: temp=39.8 th2: temp=43.6 th3: temp=41.9 sysload=0.07 cputime=257.953 memavail=7397360 print_time=3418.697 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 3397.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=20001828 bytes_read=2627058 bytes_retransmit=9 bytes_invalid=0 send_seq=353414 receive_seq=353414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015300 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21346 bytes_read=67755 bytes_retransmit=0 bytes_invalid=0 send_seq=3529 receive_seq=3529 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997272 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=121902 bytes_read=3598798 bytes_retransmit=9 bytes_invalid=0 send_seq=16309 receive_seq=16309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997683 toolboard_t1: mcu_awake=0.024 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=64226 bytes_read=1154387 bytes_retransmit=9 bytes_invalid=0 send_seq=8160 receive_seq=8160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=21613 bytes_read=864765 bytes_retransmit=9 bytes_invalid=0 send_seq=3543 receive_seq=3543 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999514 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22099 bytes_read=66445 bytes_retransmit=9 bytes_invalid=0 send_seq=3530 receive_seq=3530 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999451 Octopus_Pro_H723_V1.1: temp=33.8 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76030 bytes_read=1434906 bytes_retransmit=0 bytes_invalid=0 send_seq=8073 receive_seq=8073 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998711 coil_temp=17.9 refs=0 mcu_temp=21.01 supply_voltage=3.012 th0: temp=40.8 th1: temp=39.3 th2: temp=43.5 th3: temp=42.2 sysload=0.07 cputime=258.069 memavail=7399136 print_time=3419.697 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 3398.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=20002830 bytes_read=2627902 bytes_retransmit=9 bytes_invalid=0 send_seq=353468 receive_seq=353468 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015272 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21352 bytes_read=67771 bytes_retransmit=0 bytes_invalid=0 send_seq=3530 receive_seq=3530 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997341 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=121908 bytes_read=3598926 bytes_retransmit=9 bytes_invalid=0 send_seq=16310 receive_seq=16310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997846 toolboard_t1: mcu_awake=0.024 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=64232 bytes_read=1154515 bytes_retransmit=9 bytes_invalid=0 send_seq=8161 receive_seq=8161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997612 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=21619 bytes_read=865044 bytes_retransmit=9 bytes_invalid=0 send_seq=3544 receive_seq=3544 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999513 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22105 bytes_read=66461 bytes_retransmit=9 bytes_invalid=0 send_seq=3531 receive_seq=3531 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999483 Octopus_Pro_H723_V1.1: temp=33.7 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76190 bytes_read=1437949 bytes_retransmit=0 bytes_invalid=0 send_seq=8089 receive_seq=8089 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998809 coil_temp=17.9 refs=1 mcu_temp=20.99 supply_voltage=3.012 th0: temp=40.0 th1: temp=39.7 th2: temp=43.6 th3: temp=42.0 sysload=0.07 cputime=258.271 memavail=7399136 print_time=3420.605 buffer_time=0.079 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Extruder extruder already active
Extruder 'extruder' now syncing with 'extruder'
Extruder 'extruder1' now syncing with 'extruder'
RatOS | SET_PRESSURE_ADVANCE:: T0
extruder: pressure_advance: 0.008000
pressure_advance_smooth_time: 0.040000
RatOS | SET_PRESSURE_ADVANCE:: T1
extruder1: pressure_advance: 0.008000
pressure_advance_smooth_time: 0.040000
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 3399.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=20007004 bytes_read=2628671 bytes_retransmit=9 bytes_invalid=0 send_seq=353554 receive_seq=353554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015245 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21358 bytes_read=67787 bytes_retransmit=0 bytes_invalid=0 send_seq=3531 receive_seq=3531 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997387 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=121914 bytes_read=3599036 bytes_retransmit=9 bytes_invalid=0 send_seq=16311 receive_seq=16311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997858 toolboard_t1: mcu_awake=0.024 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=64238 bytes_read=1154611 bytes_retransmit=9 bytes_invalid=0 send_seq=8162 receive_seq=8162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997666 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=21625 bytes_read=865293 bytes_retransmit=9 bytes_invalid=0 send_seq=3545 receive_seq=3545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999513 adj=47997729 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22111 bytes_read=66477 bytes_retransmit=9 bytes_invalid=0 send_seq=3532 receive_seq=3532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999486 Octopus_Pro_H723_V1.1: temp=33.5 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76203 bytes_read=1438649 bytes_retransmit=0 bytes_invalid=0 send_seq=8091 receive_seq=8091 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998878 coil_temp=17.9 refs=0 mcu_temp=20.99 supply_voltage=3.012 th0: temp=40.8 th1: temp=39.4 th2: temp=44.0 th3: temp=42.5 sysload=0.07 cputime=258.408 memavail=7399136 print_time=3423.029 buffer_time=1.502 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 3400.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=20007302 bytes_read=2629112 bytes_retransmit=9 bytes_invalid=0 send_seq=353577 receive_seq=353577 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015227 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21364 bytes_read=67803 bytes_retransmit=0 bytes_invalid=0 send_seq=3532 receive_seq=3532 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999218 adj=49997404 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=121920 bytes_read=3599127 bytes_retransmit=9 bytes_invalid=0 send_seq=16312 receive_seq=16312 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997840 toolboard_t1: mcu_awake=0.024 mcu_task_avg=0.000017 mcu_task_stddev=0.000011 bytes_write=64244 bytes_read=1154702 bytes_retransmit=9 bytes_invalid=0 send_seq=8163 receive_seq=8163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997699 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=21631 bytes_read=865527 bytes_retransmit=9 bytes_invalid=0 send_seq=3546 receive_seq=3546 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999513 adj=47997750 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22117 bytes_read=66493 bytes_retransmit=9 bytes_invalid=0 send_seq=3533 receive_seq=3533 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999482 Octopus_Pro_H723_V1.1: temp=33.5 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76209 bytes_read=1439005 bytes_retransmit=0 bytes_invalid=0 send_seq=8092 receive_seq=8092 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998811 coil_temp=17.9 refs=0 mcu_temp=20.98 supply_voltage=3.012 th0: temp=40.1 th1: temp=39.7 th2: temp=44.0 th3: temp=42.4 sysload=0.07 cputime=258.450 memavail=7399136 print_time=3423.029 buffer_time=0.502 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Stats 3401.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=20007600 bytes_read=2629537 bytes_retransmit=9 bytes_invalid=0 send_seq=353600 receive_seq=353600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015211 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21370 bytes_read=67832 bytes_retransmit=0 bytes_invalid=0 send_seq=3533 receive_seq=3533 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999218 adj=49997459 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=121926 bytes_read=3599246 bytes_retransmit=9 bytes_invalid=0 send_seq=16313 receive_seq=16313 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997869 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=64250 bytes_read=1154835 bytes_retransmit=9 bytes_invalid=0 send_seq=8164 receive_seq=8164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997735 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21637 bytes_read=865821 bytes_retransmit=9 bytes_invalid=0 send_seq=3547 receive_seq=3547 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999514 adj=47997780 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22123 bytes_read=66509 bytes_retransmit=9 bytes_invalid=0 send_seq=3534 receive_seq=3534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999523 Octopus_Pro_H723_V1.1: temp=33.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76215 bytes_read=1439361 bytes_retransmit=0 bytes_invalid=0 send_seq=8093 receive_seq=8093 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998849 coil_temp=17.9 refs=0 mcu_temp=20.97 supply_voltage=3.012 th0: temp=40.6 th1: temp=39.6 th2: temp=44.3 th3: temp=42.7 sysload=0.07 cputime=258.493 memavail=7399136 print_time=3423.029 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Stats 3402.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=20007898 bytes_read=2629991 bytes_retransmit=9 bytes_invalid=0 send_seq=353623 receive_seq=353623 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015194 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21376 bytes_read=67848 bytes_retransmit=0 bytes_invalid=0 send_seq=3534 receive_seq=3534 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997472 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=121932 bytes_read=3599339 bytes_retransmit=9 bytes_invalid=0 send_seq=16314 receive_seq=16314 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997866 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=64256 bytes_read=1154928 bytes_retransmit=9 bytes_invalid=0 send_seq=8165 receive_seq=8165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997751 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21643 bytes_read=866070 bytes_retransmit=9 bytes_invalid=0 send_seq=3548 receive_seq=3548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999514 adj=47997819 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22129 bytes_read=66536 bytes_retransmit=9 bytes_invalid=0 send_seq=3535 receive_seq=3535 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999542 Octopus_Pro_H723_V1.1: temp=33.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76221 bytes_read=1439717 bytes_retransmit=0 bytes_invalid=0 send_seq=8094 receive_seq=8094 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998844 coil_temp=17.9 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=40.8 th1: temp=39.8 th2: temp=44.3 th3: temp=42.8 sysload=0.07 cputime=258.535 memavail=7399136 print_time=3423.029 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 3403.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=20008196 bytes_read=2630412 bytes_retransmit=9 bytes_invalid=0 send_seq=353646 receive_seq=353646 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015191 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21382 bytes_read=67864 bytes_retransmit=0 bytes_invalid=0 send_seq=3535 receive_seq=3535 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999218 adj=49997456 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=121938 bytes_read=3599434 bytes_retransmit=9 bytes_invalid=0 send_seq=16315 receive_seq=16315 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997853 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=64262 bytes_read=1155023 bytes_retransmit=9 bytes_invalid=0 send_seq=8166 receive_seq=8166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997748 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21649 bytes_read=866304 bytes_retransmit=9 bytes_invalid=0 send_seq=3549 receive_seq=3549 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999514 adj=47997817 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22135 bytes_read=66552 bytes_retransmit=9 bytes_invalid=0 send_seq=3536 receive_seq=3536 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999542 Octopus_Pro_H723_V1.1: temp=33.3 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76227 bytes_read=1440073 bytes_retransmit=0 bytes_invalid=0 send_seq=8095 receive_seq=8095 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998823 coil_temp=17.9 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=40.6 th1: temp=40.1 th2: temp=44.5 th3: temp=42.9 sysload=0.06 cputime=258.576 memavail=7399136 print_time=3423.029 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 3404.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000003 mcu_task_stddev=0.000003 bytes_write=20008494 bytes_read=2630837 bytes_retransmit=9 bytes_invalid=0 send_seq=353669 receive_seq=353669 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015186 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21388 bytes_read=67880 bytes_retransmit=0 bytes_invalid=0 send_seq=3536 receive_seq=3536 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997444 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=121944 bytes_read=3599576 bytes_retransmit=9 bytes_invalid=0 send_seq=16316 receive_seq=16316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997827 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=64268 bytes_read=1155151 bytes_retransmit=9 bytes_invalid=0 send_seq=8167 receive_seq=8167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997716 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21655 bytes_read=866598 bytes_retransmit=9 bytes_invalid=0 send_seq=3550 receive_seq=3550 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997792 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22141 bytes_read=66568 bytes_retransmit=9 bytes_invalid=0 send_seq=3537 receive_seq=3537 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999536 Octopus_Pro_H723_V1.1: temp=33.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76233 bytes_read=1440429 bytes_retransmit=0 bytes_invalid=0 send_seq=8096 receive_seq=8096 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998822 coil_temp=17.8 refs=0 mcu_temp=20.97 supply_voltage=3.012 th0: temp=40.3 th1: temp=40.2 th2: temp=44.8 th3: temp=43.0 sysload=0.06 cputime=258.619 memavail=7399136 print_time=3423.029 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3405.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=20008792 bytes_read=2631306 bytes_retransmit=9 bytes_invalid=0 send_seq=353692 receive_seq=353692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015174 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21394 bytes_read=67896 bytes_retransmit=0 bytes_invalid=0 send_seq=3537 receive_seq=3537 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997405 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=121950 bytes_read=3599676 bytes_retransmit=9 bytes_invalid=0 send_seq=16317 receive_seq=16317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997796 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=64274 bytes_read=1155251 bytes_retransmit=9 bytes_invalid=0 send_seq=8168 receive_seq=8168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997701 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21661 bytes_read=866832 bytes_retransmit=9 bytes_invalid=0 send_seq=3551 receive_seq=3551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997796 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22147 bytes_read=66584 bytes_retransmit=9 bytes_invalid=0 send_seq=3538 receive_seq=3538 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999514 Octopus_Pro_H723_V1.1: temp=33.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76239 bytes_read=1440785 bytes_retransmit=0 bytes_invalid=0 send_seq=8097 receive_seq=8097 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998785 coil_temp=17.8 refs=0 mcu_temp=20.98 supply_voltage=3.012 th0: temp=41.5 th1: temp=40.2 th2: temp=44.8 th3: temp=43.2 sysload=0.06 cputime=258.660 memavail=7399136 print_time=3423.029 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
RatOS:: All requested axes already homed. Skipping homing.
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 3406.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=20010182 bytes_read=2631821 bytes_retransmit=9 bytes_invalid=0 send_seq=353733 receive_seq=353733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=0 freq=400015181 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21400 bytes_read=67925 bytes_retransmit=0 bytes_invalid=0 send_seq=3538 receive_seq=3538 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999218 adj=49997409 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=121956 bytes_read=3599776 bytes_retransmit=9 bytes_invalid=0 send_seq=16318 receive_seq=16318 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997798 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=64280 bytes_read=1155365 bytes_retransmit=9 bytes_invalid=0 send_seq=8169 receive_seq=8169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997712 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=21667 bytes_read=867081 bytes_retransmit=9 bytes_invalid=0 send_seq=3552 receive_seq=3552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997800 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22153 bytes_read=66600 bytes_retransmit=9 bytes_invalid=0 send_seq=3539 receive_seq=3539 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999501 Octopus_Pro_H723_V1.1: temp=33.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76245 bytes_read=1441141 bytes_retransmit=0 bytes_invalid=0 send_seq=8098 receive_seq=8098 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998787 coil_temp=17.9 refs=0 mcu_temp=20.98 supply_voltage=3.012 th0: temp=41.2 th1: temp=40.3 th2: temp=44.8 th3: temp=43.3 sysload=0.06 cputime=258.743 memavail=7399152 print_time=3429.096 buffer_time=0.557 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Extruder extruder already active
Extruder 'extruder' now syncing with 'extruder'
Extruder 'extruder1' now syncing with 'extruder1'
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
RatOS | IDEX:: Selecting T1..
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 20.000000
RatOS | IDEX:: Toolhead offset applied for T1: X=-0.0 Y=-0.0 Z=-0.0
Activating extruder extruder1
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
Probing point (250.000, 250.000, 20.000)
Stats 3407.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=20013952 bytes_read=2632531 bytes_retransmit=9 bytes_invalid=0 send_seq=353813 receive_seq=353813 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=0 freq=400015178 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21406 bytes_read=67941 bytes_retransmit=0 bytes_invalid=0 send_seq=3539 receive_seq=3539 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999220 adj=49997377 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=121962 bytes_read=3599904 bytes_retransmit=9 bytes_invalid=0 send_seq=16319 receive_seq=16319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997746 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=64286 bytes_read=1155493 bytes_retransmit=9 bytes_invalid=0 send_seq=8170 receive_seq=8170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997653 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=21673 bytes_read=867393 bytes_retransmit=9 bytes_invalid=0 send_seq=3553 receive_seq=3553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997776 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22159 bytes_read=66627 bytes_retransmit=9 bytes_invalid=0 send_seq=3540 receive_seq=3540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999478 Octopus_Pro_H723_V1.1: temp=33.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76251 bytes_read=1441497 bytes_retransmit=0 bytes_invalid=0 send_seq=8099 receive_seq=8099 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998731 coil_temp=17.8 refs=0 mcu_temp=20.99 supply_voltage=3.012 th0: temp=40.8 th1: temp=40.5 th2: temp=45.1 th3: temp=43.4 sysload=0.06 cputime=258.863 memavail=7399152 print_time=3430.573 buffer_time=1.031 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 3408.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=20014581 bytes_read=2633000 bytes_retransmit=9 bytes_invalid=0 send_seq=353839 receive_seq=353839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015170 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21412 bytes_read=67957 bytes_retransmit=0 bytes_invalid=0 send_seq=3540 receive_seq=3540 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999219 adj=49997380 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=121968 bytes_read=3600004 bytes_retransmit=9 bytes_invalid=0 send_seq=16320 receive_seq=16320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997742 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=64292 bytes_read=1155593 bytes_retransmit=9 bytes_invalid=0 send_seq=8171 receive_seq=8171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997629 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=21679 bytes_read=867627 bytes_retransmit=9 bytes_invalid=0 send_seq=3554 receive_seq=3554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997741 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22165 bytes_read=66643 bytes_retransmit=9 bytes_invalid=0 send_seq=3541 receive_seq=3541 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999477 Octopus_Pro_H723_V1.1: temp=32.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76257 bytes_read=1441853 bytes_retransmit=0 bytes_invalid=0 send_seq=8100 receive_seq=8100 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998713 coil_temp=17.8 refs=0 mcu_temp=20.99 supply_voltage=3.012 th0: temp=40.8 th1: temp=40.4 th2: temp=45.0 th3: temp=43.3 sysload=0.06 cputime=258.913 memavail=7392856 print_time=3430.573 buffer_time=0.029 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t1' measurements
toolhead: max_velocity: 600.000000
max_accel: 8379.841000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance testing
Testing frequency 10 Hz
Testing frequency 11 Hz
Testing frequency 12 Hz
Stats 3409.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=20017195 bytes_read=2633605 bytes_retransmit=9 bytes_invalid=0 send_seq=353898 receive_seq=353898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015164 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21418 bytes_read=67973 bytes_retransmit=0 bytes_invalid=0 send_seq=3541 receive_seq=3541 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999219 adj=49997383 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=121974 bytes_read=3600118 bytes_retransmit=9 bytes_invalid=0 send_seq=16321 receive_seq=16321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997754 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=64461 bytes_read=1158386 bytes_retransmit=9 bytes_invalid=0 send_seq=8191 receive_seq=8191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997640 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=21685 bytes_read=867861 bytes_retransmit=9 bytes_invalid=0 send_seq=3555 receive_seq=3555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997744 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22171 bytes_read=66659 bytes_retransmit=9 bytes_invalid=0 send_seq=3542 receive_seq=3542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999474 Octopus_Pro_H723_V1.1: temp=32.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76263 bytes_read=1442209 bytes_retransmit=0 bytes_invalid=0 send_seq=8101 receive_seq=8101 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998742 coil_temp=17.8 refs=0 mcu_temp=20.99 supply_voltage=3.012 th0: temp=40.9 th1: temp=40.5 th2: temp=45.3 th3: temp=43.4 sysload=0.06 cputime=259.078 memavail=7399276 print_time=3433.769 buffer_time=2.224 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 13 Hz
Stats 3410.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20018256 bytes_read=2634095 bytes_retransmit=9 bytes_invalid=0 send_seq=353931 receive_seq=353931 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=0 freq=400015150 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21424 bytes_read=67989 bytes_retransmit=0 bytes_invalid=0 send_seq=3542 receive_seq=3542 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999218 adj=49997348 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=121980 bytes_read=3600246 bytes_retransmit=9 bytes_invalid=0 send_seq=16322 receive_seq=16322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997821 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=64537 bytes_read=1161413 bytes_retransmit=9 bytes_invalid=0 send_seq=8202 receive_seq=8202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997638 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=21691 bytes_read=868155 bytes_retransmit=9 bytes_invalid=0 send_seq=3556 receive_seq=3556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997708 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22177 bytes_read=66675 bytes_retransmit=9 bytes_invalid=0 send_seq=3543 receive_seq=3543 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999466 Octopus_Pro_H723_V1.1: temp=32.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76269 bytes_read=1442565 bytes_retransmit=0 bytes_invalid=0 send_seq=8102 receive_seq=8102 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998714 coil_temp=17.8 refs=0 mcu_temp=20.99 supply_voltage=3.012 th0: temp=41.0 th1: temp=40.8 th2: temp=45.2 th3: temp=43.2 sysload=0.06 cputime=259.148 memavail=7399276 print_time=3434.612 buffer_time=2.066 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 14 Hz
Stats 3411.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20019710 bytes_read=2634624 bytes_retransmit=9 bytes_invalid=0 send_seq=353969 receive_seq=353969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=0 freq=400015218 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21430 bytes_read=68018 bytes_retransmit=0 bytes_invalid=0 send_seq=3543 receive_seq=3543 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997352 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=121986 bytes_read=3600346 bytes_retransmit=9 bytes_invalid=0 send_seq=16323 receive_seq=16323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997856 toolboard_t1: mcu_awake=0.166 mcu_task_avg=0.000111 mcu_task_stddev=0.000071 bytes_write=64613 bytes_read=1164479 bytes_retransmit=9 bytes_invalid=0 send_seq=8213 receive_seq=8213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997664 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21697 bytes_read=868404 bytes_retransmit=9 bytes_invalid=0 send_seq=3557 receive_seq=3557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997723 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22183 bytes_read=66691 bytes_retransmit=9 bytes_invalid=0 send_seq=3544 receive_seq=3544 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999466 Octopus_Pro_H723_V1.1: temp=32.7 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76275 bytes_read=1442921 bytes_retransmit=0 bytes_invalid=0 send_seq=8103 receive_seq=8103 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998721 coil_temp=17.8 refs=0 mcu_temp=20.98 supply_voltage=3.012 th0: temp=41.1 th1: temp=40.7 th2: temp=45.4 th3: temp=43.2 sysload=0.06 cputime=259.218 memavail=7399276 print_time=3435.634 buffer_time=2.089 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 15 Hz
Stats 3412.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20021452 bytes_read=2635144 bytes_retransmit=9 bytes_invalid=0 send_seq=354011 receive_seq=354011 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=0 freq=400015237 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21436 bytes_read=68034 bytes_retransmit=0 bytes_invalid=0 send_seq=3544 receive_seq=3544 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997230 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=121992 bytes_read=3600446 bytes_retransmit=9 bytes_invalid=0 send_seq=16324 receive_seq=16324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997688 toolboard_t1: mcu_awake=0.166 mcu_task_avg=0.000111 mcu_task_stddev=0.000071 bytes_write=64689 bytes_read=1167537 bytes_retransmit=9 bytes_invalid=0 send_seq=8224 receive_seq=8224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997508 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21703 bytes_read=868620 bytes_retransmit=9 bytes_invalid=0 send_seq=3558 receive_seq=3558 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997609 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22189 bytes_read=66718 bytes_retransmit=9 bytes_invalid=0 send_seq=3545 receive_seq=3545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999435 Octopus_Pro_H723_V1.1: temp=32.7 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76281 bytes_read=1443277 bytes_retransmit=0 bytes_invalid=0 send_seq=8104 receive_seq=8104 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998643 coil_temp=17.8 refs=0 mcu_temp=20.98 supply_voltage=3.012 th0: temp=41.0 th1: temp=41.0 th2: temp=45.5 th3: temp=43.7 sysload=0.06 cputime=259.290 memavail=7399276 print_time=3436.833 buffer_time=2.288 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 16 Hz
Stats 3413.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20022654 bytes_read=2635624 bytes_retransmit=9 bytes_invalid=0 send_seq=354045 receive_seq=354045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=0 freq=400015221 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21442 bytes_read=68050 bytes_retransmit=0 bytes_invalid=0 send_seq=3545 receive_seq=3545 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997221 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=121998 bytes_read=3600574 bytes_retransmit=9 bytes_invalid=0 send_seq=16325 receive_seq=16325 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997659 toolboard_t1: mcu_awake=0.166 mcu_task_avg=0.000111 mcu_task_stddev=0.000071 bytes_write=64765 bytes_read=1170621 bytes_retransmit=9 bytes_invalid=0 send_seq=8235 receive_seq=8235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21709 bytes_read=868914 bytes_retransmit=9 bytes_invalid=0 send_seq=3559 receive_seq=3559 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22195 bytes_read=66734 bytes_retransmit=9 bytes_invalid=0 send_seq=3546 receive_seq=3546 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999432 Octopus_Pro_H723_V1.1: temp=32.5 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76287 bytes_read=1443633 bytes_retransmit=0 bytes_invalid=0 send_seq=8105 receive_seq=8105 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998644 coil_temp=17.8 refs=0 mcu_temp=20.98 supply_voltage=3.012 th0: temp=41.4 th1: temp=41.3 th2: temp=45.6 th3: temp=43.8 sysload=0.05 cputime=259.361 memavail=7399292 print_time=3437.748 buffer_time=2.202 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 17 Hz
Stats 3414.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20024224 bytes_read=2636162 bytes_retransmit=9 bytes_invalid=0 send_seq=354086 receive_seq=354086 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=0 freq=400015234 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21448 bytes_read=68066 bytes_retransmit=0 bytes_invalid=0 send_seq=3546 receive_seq=3546 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997262 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122004 bytes_read=3600688 bytes_retransmit=9 bytes_invalid=0 send_seq=16326 receive_seq=16326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997688 toolboard_t1: mcu_awake=0.166 mcu_task_avg=0.000111 mcu_task_stddev=0.000071 bytes_write=64841 bytes_read=1173677 bytes_retransmit=9 bytes_invalid=0 send_seq=8246 receive_seq=8246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997556 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21715 bytes_read=869148 bytes_retransmit=9 bytes_invalid=0 send_seq=3560 receive_seq=3560 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22201 bytes_read=66750 bytes_retransmit=9 bytes_invalid=0 send_seq=3547 receive_seq=3547 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=32.4 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76293 bytes_read=1443989 bytes_retransmit=0 bytes_invalid=0 send_seq=8106 receive_seq=8106 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998655 coil_temp=17.8 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=41.4 th1: temp=41.1 th2: temp=45.7 th3: temp=43.7 sysload=0.05 cputime=259.430 memavail=7399292 print_time=3438.657 buffer_time=2.111 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 18 Hz
Stats 3415.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=20025588 bytes_read=2636667 bytes_retransmit=9 bytes_invalid=0 send_seq=354122 receive_seq=354122 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015242 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21454 bytes_read=68082 bytes_retransmit=0 bytes_invalid=0 send_seq=3547 receive_seq=3547 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997251 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122010 bytes_read=3600788 bytes_retransmit=9 bytes_invalid=0 send_seq=16327 receive_seq=16327 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997677 toolboard_t1: mcu_awake=0.166 mcu_task_avg=0.000111 mcu_task_stddev=0.000071 bytes_write=64917 bytes_read=1176734 bytes_retransmit=9 bytes_invalid=0 send_seq=8257 receive_seq=8257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997545 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21721 bytes_read=869382 bytes_retransmit=9 bytes_invalid=0 send_seq=3561 receive_seq=3561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22207 bytes_read=66766 bytes_retransmit=9 bytes_invalid=0 send_seq=3548 receive_seq=3548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999433 Octopus_Pro_H723_V1.1: temp=32.6 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76299 bytes_read=1444345 bytes_retransmit=0 bytes_invalid=0 send_seq=8107 receive_seq=8107 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998643 coil_temp=17.8 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=41.2 th1: temp=41.4 th2: temp=45.7 th3: temp=44.0 sysload=0.05 cputime=259.501 memavail=7399292 print_time=3439.603 buffer_time=2.057 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 19 Hz
Stats 3416.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=20027524 bytes_read=2637231 bytes_retransmit=9 bytes_invalid=0 send_seq=354170 receive_seq=354170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=0 freq=400015233 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21460 bytes_read=68111 bytes_retransmit=0 bytes_invalid=0 send_seq=3548 receive_seq=3548 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997246 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122016 bytes_read=3600916 bytes_retransmit=9 bytes_invalid=0 send_seq=16328 receive_seq=16328 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997664 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=64993 bytes_read=1179894 bytes_retransmit=9 bytes_invalid=0 send_seq=8268 receive_seq=8268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997527 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21727 bytes_read=869691 bytes_retransmit=9 bytes_invalid=0 send_seq=3562 receive_seq=3562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22213 bytes_read=66782 bytes_retransmit=9 bytes_invalid=0 send_seq=3549 receive_seq=3549 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999432 Octopus_Pro_H723_V1.1: temp=32.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76305 bytes_read=1444701 bytes_retransmit=0 bytes_invalid=0 send_seq=8108 receive_seq=8108 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998638 coil_temp=17.8 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=41.4 th1: temp=41.2 th2: temp=46.1 th3: temp=44.0 sysload=0.05 cputime=259.577 memavail=7398808 print_time=3440.815 buffer_time=2.267 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 20 Hz
Stats 3417.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=20029213 bytes_read=2637776 bytes_retransmit=9 bytes_invalid=0 send_seq=354214 receive_seq=354214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=0 freq=400015234 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21466 bytes_read=68127 bytes_retransmit=0 bytes_invalid=0 send_seq=3549 receive_seq=3549 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997277 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122022 bytes_read=3601016 bytes_retransmit=9 bytes_invalid=0 send_seq=16329 receive_seq=16329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997709 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65069 bytes_read=1182952 bytes_retransmit=9 bytes_invalid=0 send_seq=8279 receive_seq=8279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997570 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21733 bytes_read=869925 bytes_retransmit=9 bytes_invalid=0 send_seq=3563 receive_seq=3563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22219 bytes_read=66809 bytes_retransmit=9 bytes_invalid=0 send_seq=3550 receive_seq=3550 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=32.3 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76311 bytes_read=1445057 bytes_retransmit=0 bytes_invalid=0 send_seq=8109 receive_seq=8109 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998656 coil_temp=17.8 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=41.5 th1: temp=41.7 th2: temp=46.0 th3: temp=43.9 sysload=0.05 cputime=259.648 memavail=7398808 print_time=3441.685 buffer_time=2.137 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 21 Hz
Stats 3418.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=20030770 bytes_read=2638291 bytes_retransmit=9 bytes_invalid=0 send_seq=354255 receive_seq=354255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015235 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21472 bytes_read=68143 bytes_retransmit=0 bytes_invalid=0 send_seq=3550 receive_seq=3550 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997270 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122028 bytes_read=3601116 bytes_retransmit=9 bytes_invalid=0 send_seq=16330 receive_seq=16330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997697 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65145 bytes_read=1186008 bytes_retransmit=9 bytes_invalid=0 send_seq=8290 receive_seq=8290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997577 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21739 bytes_read=870159 bytes_retransmit=9 bytes_invalid=0 send_seq=3564 receive_seq=3564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22225 bytes_read=66825 bytes_retransmit=9 bytes_invalid=0 send_seq=3551 receive_seq=3551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999440 Octopus_Pro_H723_V1.1: temp=32.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76317 bytes_read=1445413 bytes_retransmit=0 bytes_invalid=0 send_seq=8110 receive_seq=8110 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998649 coil_temp=17.8 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=41.6 th1: temp=41.7 th2: temp=46.0 th3: temp=44.1 sysload=0.21 cputime=259.720 memavail=7398808 print_time=3442.649 buffer_time=2.101 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 22 Hz
Stats 3419.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=20032765 bytes_read=2638855 bytes_retransmit=9 bytes_invalid=0 send_seq=354303 receive_seq=354303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=400015246 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21478 bytes_read=68159 bytes_retransmit=0 bytes_invalid=0 send_seq=3551 receive_seq=3551 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999215 adj=49997270 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122034 bytes_read=3601258 bytes_retransmit=9 bytes_invalid=0 send_seq=16331 receive_seq=16331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997716 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65221 bytes_read=1189093 bytes_retransmit=9 bytes_invalid=0 send_seq=8301 receive_seq=8301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997569 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21745 bytes_read=870453 bytes_retransmit=9 bytes_invalid=0 send_seq=3565 receive_seq=3565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22231 bytes_read=66841 bytes_retransmit=9 bytes_invalid=0 send_seq=3552 receive_seq=3552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=32.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76323 bytes_read=1445769 bytes_retransmit=0 bytes_invalid=0 send_seq=8111 receive_seq=8111 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998649 coil_temp=17.8 refs=0 mcu_temp=20.96 supply_voltage=3.012 th0: temp=41.8 th1: temp=41.7 th2: temp=45.8 th3: temp=44.2 sysload=0.21 cputime=259.796 memavail=7398808 print_time=3443.830 buffer_time=2.281 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 23 Hz
Stats 3420.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20034530 bytes_read=2639425 bytes_retransmit=9 bytes_invalid=0 send_seq=354349 receive_seq=354349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=0 freq=400015243 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21484 bytes_read=68175 bytes_retransmit=0 bytes_invalid=0 send_seq=3552 receive_seq=3552 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997257 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122040 bytes_read=3601358 bytes_retransmit=9 bytes_invalid=0 send_seq=16332 receive_seq=16332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997706 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65297 bytes_read=1192149 bytes_retransmit=9 bytes_invalid=0 send_seq=8312 receive_seq=8312 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21751 bytes_read=870687 bytes_retransmit=9 bytes_invalid=0 send_seq=3566 receive_seq=3566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22237 bytes_read=66857 bytes_retransmit=9 bytes_invalid=0 send_seq=3553 receive_seq=3553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=32.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76329 bytes_read=1446125 bytes_retransmit=0 bytes_invalid=0 send_seq=8112 receive_seq=8112 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998650 coil_temp=17.8 refs=0 mcu_temp=20.95 supply_voltage=3.012 th0: temp=41.8 th1: temp=42.0 th2: temp=46.0 th3: temp=44.2 sysload=0.21 cputime=259.867 memavail=7398808 print_time=3444.695 buffer_time=2.146 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 24 Hz
Stats 3421.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20036226 bytes_read=2639971 bytes_retransmit=9 bytes_invalid=0 send_seq=354394 receive_seq=354394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015243 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21496 bytes_read=68220 bytes_retransmit=0 bytes_invalid=0 send_seq=3554 receive_seq=3554 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999214 adj=49997289 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122052 bytes_read=3601474 bytes_retransmit=9 bytes_invalid=0 send_seq=16334 receive_seq=16334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997743 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65379 bytes_read=1195239 bytes_retransmit=9 bytes_invalid=0 send_seq=8324 receive_seq=8324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997548 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21763 bytes_read=870952 bytes_retransmit=9 bytes_invalid=0 send_seq=3568 receive_seq=3568 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22249 bytes_read=66889 bytes_retransmit=9 bytes_invalid=0 send_seq=3555 receive_seq=3555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999439 Octopus_Pro_H723_V1.1: temp=32.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76341 bytes_read=1446497 bytes_retransmit=0 bytes_invalid=0 send_seq=8114 receive_seq=8114 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998666 coil_temp=17.8 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=41.6 th1: temp=41.9 th2: temp=46.2 th3: temp=44.3 sysload=0.21 cputime=259.940 memavail=7398808 print_time=3445.658 buffer_time=2.108 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 25 Hz
Stats 3422.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20038436 bytes_read=2640560 bytes_retransmit=9 bytes_invalid=0 send_seq=354447 receive_seq=354447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015248 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21502 bytes_read=68236 bytes_retransmit=0 bytes_invalid=0 send_seq=3555 receive_seq=3555 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997263 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122058 bytes_read=3601602 bytes_retransmit=9 bytes_invalid=0 send_seq=16335 receive_seq=16335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997725 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65455 bytes_read=1198327 bytes_retransmit=9 bytes_invalid=0 send_seq=8335 receive_seq=8335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997540 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21769 bytes_read=871246 bytes_retransmit=9 bytes_invalid=0 send_seq=3569 receive_seq=3569 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22255 bytes_read=66916 bytes_retransmit=9 bytes_invalid=0 send_seq=3556 receive_seq=3556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999437 Octopus_Pro_H723_V1.1: temp=31.9 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76347 bytes_read=1446853 bytes_retransmit=0 bytes_invalid=0 send_seq=8115 receive_seq=8115 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998680 coil_temp=17.8 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=41.8 th1: temp=42.3 th2: temp=46.1 th3: temp=44.4 sysload=0.21 cputime=260.021 memavail=7398808 print_time=3446.872 buffer_time=2.322 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 26 Hz
Stats 3423.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20040346 bytes_read=2641130 bytes_retransmit=9 bytes_invalid=0 send_seq=354496 receive_seq=354496 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015261 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21508 bytes_read=68252 bytes_retransmit=0 bytes_invalid=0 send_seq=3556 receive_seq=3556 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997254 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122064 bytes_read=3601702 bytes_retransmit=9 bytes_invalid=0 send_seq=16336 receive_seq=16336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997715 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65524 bytes_read=1201360 bytes_retransmit=9 bytes_invalid=0 send_seq=8345 receive_seq=8345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997550 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21775 bytes_read=871480 bytes_retransmit=9 bytes_invalid=0 send_seq=3570 receive_seq=3570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22261 bytes_read=66932 bytes_retransmit=9 bytes_invalid=0 send_seq=3557 receive_seq=3557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999440 Octopus_Pro_H723_V1.1: temp=31.8 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76353 bytes_read=1447209 bytes_retransmit=0 bytes_invalid=0 send_seq=8116 receive_seq=8116 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998668 coil_temp=17.8 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=41.9 th1: temp=41.9 th2: temp=46.3 th3: temp=44.4 sysload=0.19 cputime=260.092 memavail=7398836 print_time=3447.740 buffer_time=2.190 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 27 Hz
Stats 3424.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20042202 bytes_read=2641673 bytes_retransmit=9 bytes_invalid=0 send_seq=354543 receive_seq=354543 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015244 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21514 bytes_read=68268 bytes_retransmit=0 bytes_invalid=0 send_seq=3557 receive_seq=3557 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997228 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122070 bytes_read=3601816 bytes_retransmit=9 bytes_invalid=0 send_seq=16337 receive_seq=16337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997683 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65600 bytes_read=1204476 bytes_retransmit=9 bytes_invalid=0 send_seq=8356 receive_seq=8356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997522 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21781 bytes_read=871714 bytes_retransmit=9 bytes_invalid=0 send_seq=3571 receive_seq=3571 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999514 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22267 bytes_read=66948 bytes_retransmit=9 bytes_invalid=0 send_seq=3558 receive_seq=3558 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999435 Octopus_Pro_H723_V1.1: temp=31.8 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76359 bytes_read=1447565 bytes_retransmit=0 bytes_invalid=0 send_seq=8117 receive_seq=8117 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998656 coil_temp=17.8 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=42.5 th1: temp=42.3 th2: temp=46.6 th3: temp=44.2 sysload=0.19 cputime=260.165 memavail=7398836 print_time=3448.710 buffer_time=2.160 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 28 Hz
Stats 3425.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20043955 bytes_read=2642235 bytes_retransmit=9 bytes_invalid=0 send_seq=354588 receive_seq=354588 retransmit_seq=2 srtt=0.000 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015243 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21520 bytes_read=68284 bytes_retransmit=0 bytes_invalid=0 send_seq=3558 receive_seq=3558 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997255 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122076 bytes_read=3601944 bytes_retransmit=9 bytes_invalid=0 send_seq=16338 receive_seq=16338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997719 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65676 bytes_read=1207560 bytes_retransmit=9 bytes_invalid=0 send_seq=8367 receive_seq=8367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997557 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21787 bytes_read=872008 bytes_retransmit=9 bytes_invalid=0 send_seq=3572 receive_seq=3572 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22273 bytes_read=66964 bytes_retransmit=9 bytes_invalid=0 send_seq=3559 receive_seq=3559 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999443 Octopus_Pro_H723_V1.1: temp=31.7 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76365 bytes_read=1447921 bytes_retransmit=0 bytes_invalid=0 send_seq=8118 receive_seq=8118 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998674 coil_temp=17.8 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=41.5 th1: temp=42.5 th2: temp=46.3 th3: temp=44.5 sysload=0.19 cputime=260.244 memavail=7394316 print_time=3449.585 buffer_time=2.034 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 29 Hz
Stats 3426.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20046269 bytes_read=2642830 bytes_retransmit=9 bytes_invalid=0 send_seq=354642 receive_seq=354642 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=0 freq=400015248 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21526 bytes_read=68313 bytes_retransmit=0 bytes_invalid=0 send_seq=3559 receive_seq=3559 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997288 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122082 bytes_read=3602044 bytes_retransmit=9 bytes_invalid=0 send_seq=16339 receive_seq=16339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997718 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65752 bytes_read=1210633 bytes_retransmit=9 bytes_invalid=0 send_seq=8378 receive_seq=8378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997558 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21793 bytes_read=872257 bytes_retransmit=9 bytes_invalid=0 send_seq=3573 receive_seq=3573 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999514 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22279 bytes_read=66980 bytes_retransmit=9 bytes_invalid=0 send_seq=3560 receive_seq=3560 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999452 Octopus_Pro_H723_V1.1: temp=31.6 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76371 bytes_read=1448277 bytes_retransmit=0 bytes_invalid=0 send_seq=8119 receive_seq=8119 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998678 coil_temp=17.8 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=42.1 th1: temp=42.4 th2: temp=46.4 th3: temp=44.5 sysload=0.19 cputime=260.331 memavail=7398868 print_time=3450.801 buffer_time=2.250 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 30 Hz
Stats 3427.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20048327 bytes_read=2643395 bytes_retransmit=9 bytes_invalid=0 send_seq=354693 receive_seq=354693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015250 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21532 bytes_read=68329 bytes_retransmit=0 bytes_invalid=0 send_seq=3560 receive_seq=3560 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997281 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122088 bytes_read=3602144 bytes_retransmit=9 bytes_invalid=0 send_seq=16340 receive_seq=16340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997712 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65828 bytes_read=1213691 bytes_retransmit=9 bytes_invalid=0 send_seq=8389 receive_seq=8389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997555 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21799 bytes_read=872491 bytes_retransmit=9 bytes_invalid=0 send_seq=3574 receive_seq=3574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999514 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22285 bytes_read=67007 bytes_retransmit=9 bytes_invalid=0 send_seq=3561 receive_seq=3561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999450 Octopus_Pro_H723_V1.1: temp=31.5 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76377 bytes_read=1448633 bytes_retransmit=0 bytes_invalid=0 send_seq=8120 receive_seq=8120 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998731 coil_temp=17.8 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=42.4 th1: temp=42.8 th2: temp=46.5 th3: temp=44.6 sysload=0.19 cputime=260.408 memavail=7398868 print_time=3451.731 buffer_time=2.179 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 31 Hz
Stats 3428.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20050106 bytes_read=2643949 bytes_retransmit=9 bytes_invalid=0 send_seq=354739 receive_seq=354739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015260 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21538 bytes_read=68345 bytes_retransmit=0 bytes_invalid=0 send_seq=3561 receive_seq=3561 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997270 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122094 bytes_read=3602272 bytes_retransmit=9 bytes_invalid=0 send_seq=16341 receive_seq=16341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997702 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65904 bytes_read=1216777 bytes_retransmit=9 bytes_invalid=0 send_seq=8400 receive_seq=8400 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997567 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21805 bytes_read=872765 bytes_retransmit=9 bytes_invalid=0 send_seq=3575 receive_seq=3575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999520 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22291 bytes_read=67023 bytes_retransmit=9 bytes_invalid=0 send_seq=3562 receive_seq=3562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999448 Octopus_Pro_H723_V1.1: temp=31.7 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76383 bytes_read=1448989 bytes_retransmit=0 bytes_invalid=0 send_seq=8121 receive_seq=8121 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998712 coil_temp=17.8 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=42.1 th1: temp=42.7 th2: temp=46.5 th3: temp=44.8 sysload=0.17 cputime=260.483 memavail=7398872 print_time=3452.593 buffer_time=2.041 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 32 Hz
Stats 3429.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20052580 bytes_read=2644559 bytes_retransmit=9 bytes_invalid=0 send_seq=354796 receive_seq=354796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=0 freq=400015253 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21544 bytes_read=68361 bytes_retransmit=0 bytes_invalid=0 send_seq=3562 receive_seq=3562 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997238 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122100 bytes_read=3602386 bytes_retransmit=9 bytes_invalid=0 send_seq=16342 receive_seq=16342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997678 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=65980 bytes_read=1219834 bytes_retransmit=9 bytes_invalid=0 send_seq=8411 receive_seq=8411 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997552 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21811 bytes_read=872999 bytes_retransmit=9 bytes_invalid=0 send_seq=3576 receive_seq=3576 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997725 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22297 bytes_read=67039 bytes_retransmit=9 bytes_invalid=0 send_seq=3563 receive_seq=3563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999446 Octopus_Pro_H723_V1.1: temp=31.7 EBB42_Gen2_v1.0_T0: temp=31.1 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76389 bytes_read=1449345 bytes_retransmit=0 bytes_invalid=0 send_seq=8122 receive_seq=8122 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998695 coil_temp=17.8 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=42.1 th1: temp=43.2 th2: temp=46.8 th3: temp=44.7 sysload=0.17 cputime=260.563 memavail=7398880 print_time=3453.836 buffer_time=2.283 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 33 Hz
Stats 3430.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20054793 bytes_read=2645144 bytes_retransmit=9 bytes_invalid=0 send_seq=354848 receive_seq=354848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015279 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21550 bytes_read=68377 bytes_retransmit=0 bytes_invalid=0 send_seq=3563 receive_seq=3563 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997265 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122106 bytes_read=3602486 bytes_retransmit=9 bytes_invalid=0 send_seq=16343 receive_seq=16343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997788 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66056 bytes_read=1222890 bytes_retransmit=9 bytes_invalid=0 send_seq=8422 receive_seq=8422 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997582 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21817 bytes_read=873233 bytes_retransmit=9 bytes_invalid=0 send_seq=3577 receive_seq=3577 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997711 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22303 bytes_read=67055 bytes_retransmit=9 bytes_invalid=0 send_seq=3564 receive_seq=3564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999451 Octopus_Pro_H723_V1.1: temp=31.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76395 bytes_read=1449701 bytes_retransmit=0 bytes_invalid=0 send_seq=8123 receive_seq=8123 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998701 coil_temp=17.8 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=42.0 th1: temp=42.6 th2: temp=46.7 th3: temp=44.9 sysload=0.17 cputime=260.638 memavail=7398880 print_time=3454.779 buffer_time=2.225 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 34 Hz
Stats 3431.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20056599 bytes_read=2645698 bytes_retransmit=9 bytes_invalid=0 send_seq=354894 receive_seq=354894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015389 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21556 bytes_read=68406 bytes_retransmit=0 bytes_invalid=0 send_seq=3564 receive_seq=3564 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997223 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122112 bytes_read=3602614 bytes_retransmit=9 bytes_invalid=0 send_seq=16344 receive_seq=16344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997732 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66132 bytes_read=1225995 bytes_retransmit=9 bytes_invalid=0 send_seq=8433 receive_seq=8433 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21823 bytes_read=873527 bytes_retransmit=9 bytes_invalid=0 send_seq=3578 receive_seq=3578 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22309 bytes_read=67071 bytes_retransmit=9 bytes_invalid=0 send_seq=3565 receive_seq=3565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999440 Octopus_Pro_H723_V1.1: temp=31.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76401 bytes_read=1450057 bytes_retransmit=0 bytes_invalid=0 send_seq=8124 receive_seq=8124 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998666 coil_temp=17.8 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=42.2 th1: temp=42.9 th2: temp=46.9 th3: temp=44.8 sysload=0.17 cputime=260.713 memavail=7398880 print_time=3455.652 buffer_time=2.097 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 35 Hz
Stats 3432.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20058855 bytes_read=2646278 bytes_retransmit=9 bytes_invalid=0 send_seq=354945 receive_seq=354945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015393 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21562 bytes_read=68422 bytes_retransmit=0 bytes_invalid=0 send_seq=3565 receive_seq=3565 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997151 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122118 bytes_read=3602714 bytes_retransmit=9 bytes_invalid=0 send_seq=16345 receive_seq=16345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997516 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66208 bytes_read=1229109 bytes_retransmit=9 bytes_invalid=0 send_seq=8444 receive_seq=8444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997352 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21829 bytes_read=873776 bytes_retransmit=9 bytes_invalid=0 send_seq=3579 receive_seq=3579 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997497 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22315 bytes_read=67098 bytes_retransmit=9 bytes_invalid=0 send_seq=3566 receive_seq=3566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999401 Octopus_Pro_H723_V1.1: temp=31.4 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76407 bytes_read=1450413 bytes_retransmit=0 bytes_invalid=0 send_seq=8125 receive_seq=8125 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998555 coil_temp=17.8 refs=0 mcu_temp=20.94 supply_voltage=3.012 th0: temp=42.3 th1: temp=43.0 th2: temp=46.8 th3: temp=44.9 sysload=0.17 cputime=260.789 memavail=7398880 print_time=3456.581 buffer_time=2.027 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 36 Hz
Stats 3433.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20061494 bytes_read=2646888 bytes_retransmit=9 bytes_invalid=0 send_seq=355005 receive_seq=355005 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=0 freq=400015374 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21568 bytes_read=68438 bytes_retransmit=0 bytes_invalid=0 send_seq=3566 receive_seq=3566 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999222 adj=49997160 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122124 bytes_read=3602814 bytes_retransmit=9 bytes_invalid=0 send_seq=16346 receive_seq=16346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997571 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66284 bytes_read=1232166 bytes_retransmit=9 bytes_invalid=0 send_seq=8455 receive_seq=8455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997370 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21835 bytes_read=874010 bytes_retransmit=9 bytes_invalid=0 send_seq=3580 receive_seq=3580 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997511 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22321 bytes_read=67114 bytes_retransmit=9 bytes_invalid=0 send_seq=3567 receive_seq=3567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999406 Octopus_Pro_H723_V1.1: temp=31.5 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76413 bytes_read=1450769 bytes_retransmit=0 bytes_invalid=0 send_seq=8126 receive_seq=8126 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998567 coil_temp=17.8 refs=0 mcu_temp=20.93 supply_voltage=3.012 th0: temp=42.9 th1: temp=43.2 th2: temp=46.9 th3: temp=44.8 sysload=0.16 cputime=260.869 memavail=7398880 print_time=3457.804 buffer_time=2.249 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 37 Hz
Stats 3434.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20063388 bytes_read=2647452 bytes_retransmit=9 bytes_invalid=0 send_seq=355053 receive_seq=355053 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=0 freq=400015386 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21574 bytes_read=68454 bytes_retransmit=0 bytes_invalid=0 send_seq=3567 receive_seq=3567 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999222 adj=49997296 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122130 bytes_read=3602956 bytes_retransmit=9 bytes_invalid=0 send_seq=16347 receive_seq=16347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997643 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66360 bytes_read=1235252 bytes_retransmit=9 bytes_invalid=0 send_seq=8466 receive_seq=8466 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997473 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21841 bytes_read=874304 bytes_retransmit=9 bytes_invalid=0 send_seq=3581 receive_seq=3581 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997582 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22327 bytes_read=67130 bytes_retransmit=9 bytes_invalid=0 send_seq=3568 receive_seq=3568 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999426 Octopus_Pro_H723_V1.1: temp=31.3 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76419 bytes_read=1451125 bytes_retransmit=0 bytes_invalid=0 send_seq=8127 receive_seq=8127 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998617 coil_temp=17.8 refs=0 mcu_temp=20.92 supply_voltage=3.012 th0: temp=42.3 th1: temp=43.1 th2: temp=46.6 th3: temp=45.1 sysload=0.16 cputime=260.945 memavail=7398880 print_time=3458.680 buffer_time=2.125 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 38 Hz
Stats 3435.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20065835 bytes_read=2648071 bytes_retransmit=9 bytes_invalid=0 send_seq=355110 receive_seq=355110 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015371 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21580 bytes_read=68470 bytes_retransmit=0 bytes_invalid=0 send_seq=3568 receive_seq=3568 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999220 adj=49997273 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122136 bytes_read=3603056 bytes_retransmit=9 bytes_invalid=0 send_seq=16348 receive_seq=16348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997617 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66436 bytes_read=1238310 bytes_retransmit=9 bytes_invalid=0 send_seq=8477 receive_seq=8477 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997466 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21847 bytes_read=874538 bytes_retransmit=9 bytes_invalid=0 send_seq=3582 receive_seq=3582 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997570 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22333 bytes_read=67146 bytes_retransmit=9 bytes_invalid=0 send_seq=3569 receive_seq=3569 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999436 Octopus_Pro_H723_V1.1: temp=31.4 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76425 bytes_read=1451481 bytes_retransmit=0 bytes_invalid=0 send_seq=8128 receive_seq=8128 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998612 coil_temp=17.8 refs=0 mcu_temp=20.91 supply_voltage=3.012 th0: temp=42.4 th1: temp=43.3 th2: temp=47.0 th3: temp=45.1 sysload=0.16 cputime=261.020 memavail=7398880 print_time=3459.595 buffer_time=2.040 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 39 Hz
Stats 3436.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20068530 bytes_read=2648681 bytes_retransmit=9 bytes_invalid=0 send_seq=355170 receive_seq=355170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015372 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21586 bytes_read=68499 bytes_retransmit=0 bytes_invalid=0 send_seq=3569 receive_seq=3569 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999219 adj=49997286 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122142 bytes_read=3603156 bytes_retransmit=9 bytes_invalid=0 send_seq=16349 receive_seq=16349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997666 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66512 bytes_read=1241384 bytes_retransmit=9 bytes_invalid=0 send_seq=8488 receive_seq=8488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997546 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21853 bytes_read=874772 bytes_retransmit=9 bytes_invalid=0 send_seq=3583 receive_seq=3583 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997599 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22339 bytes_read=67162 bytes_retransmit=9 bytes_invalid=0 send_seq=3570 receive_seq=3570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999442 Octopus_Pro_H723_V1.1: temp=31.1 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76431 bytes_read=1451837 bytes_retransmit=0 bytes_invalid=0 send_seq=8129 receive_seq=8129 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998636 coil_temp=17.8 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=42.7 th1: temp=43.3 th2: temp=46.9 th3: temp=45.0 sysload=0.16 cputime=261.101 memavail=7398904 print_time=3460.807 buffer_time=2.251 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 40 Hz
Stats 3437.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20070486 bytes_read=2649255 bytes_retransmit=9 bytes_invalid=0 send_seq=355220 receive_seq=355220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=0 freq=400015364 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21592 bytes_read=68515 bytes_retransmit=0 bytes_invalid=0 send_seq=3570 receive_seq=3570 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997273 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122148 bytes_read=3603284 bytes_retransmit=9 bytes_invalid=0 send_seq=16350 receive_seq=16350 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997673 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66588 bytes_read=1244469 bytes_retransmit=9 bytes_invalid=0 send_seq=8499 receive_seq=8499 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997620 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21859 bytes_read=875081 bytes_retransmit=9 bytes_invalid=0 send_seq=3584 receive_seq=3584 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22345 bytes_read=67189 bytes_retransmit=9 bytes_invalid=0 send_seq=3571 receive_seq=3571 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999444 Octopus_Pro_H723_V1.1: temp=31.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76437 bytes_read=1452193 bytes_retransmit=0 bytes_invalid=0 send_seq=8130 receive_seq=8130 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998642 coil_temp=17.8 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=42.7 th1: temp=43.2 th2: temp=47.0 th3: temp=45.0 sysload=0.16 cputime=261.179 memavail=7398912 print_time=3461.698 buffer_time=2.142 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 41 Hz
Stats 3438.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20073088 bytes_read=2649875 bytes_retransmit=9 bytes_invalid=0 send_seq=355279 receive_seq=355279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=23 upcoming_bytes=0 freq=400015349 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21598 bytes_read=68531 bytes_retransmit=0 bytes_invalid=0 send_seq=3571 receive_seq=3571 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997268 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122154 bytes_read=3603384 bytes_retransmit=9 bytes_invalid=0 send_seq=16351 receive_seq=16351 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997681 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66664 bytes_read=1247525 bytes_retransmit=9 bytes_invalid=0 send_seq=8510 receive_seq=8510 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997738 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21865 bytes_read=875315 bytes_retransmit=9 bytes_invalid=0 send_seq=3585 receive_seq=3585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22351 bytes_read=67205 bytes_retransmit=9 bytes_invalid=0 send_seq=3572 receive_seq=3572 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999447 Octopus_Pro_H723_V1.1: temp=31.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76443 bytes_read=1452549 bytes_retransmit=0 bytes_invalid=0 send_seq=8131 receive_seq=8131 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998675 coil_temp=17.8 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=43.0 th1: temp=43.3 th2: temp=46.8 th3: temp=45.2 sysload=0.15 cputime=261.257 memavail=7398912 print_time=3462.643 buffer_time=2.087 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 42 Hz
Stats 3439.0: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20076033 bytes_read=2650500 bytes_retransmit=9 bytes_invalid=0 send_seq=355342 receive_seq=355342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015343 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21604 bytes_read=68547 bytes_retransmit=0 bytes_invalid=0 send_seq=3572 receive_seq=3572 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997296 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=122160 bytes_read=3603498 bytes_retransmit=9 bytes_invalid=0 send_seq=16352 receive_seq=16352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997712 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66733 bytes_read=1250558 bytes_retransmit=9 bytes_invalid=0 send_seq=8520 receive_seq=8520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997727 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21871 bytes_read=875549 bytes_retransmit=9 bytes_invalid=0 send_seq=3586 receive_seq=3586 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22357 bytes_read=67221 bytes_retransmit=9 bytes_invalid=0 send_seq=3573 receive_seq=3573 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999451 Octopus_Pro_H723_V1.1: temp=31.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76449 bytes_read=1452905 bytes_retransmit=0 bytes_invalid=0 send_seq=8132 receive_seq=8132 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998689 coil_temp=17.8 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=42.7 th1: temp=43.3 th2: temp=46.9 th3: temp=45.3 sysload=0.15 cputime=261.339 memavail=7398688 print_time=3463.833 buffer_time=2.276 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 43 Hz
Stats 3440.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20078053 bytes_read=2651079 bytes_retransmit=9 bytes_invalid=0 send_seq=355390 receive_seq=355390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=0 freq=400015349 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21610 bytes_read=68563 bytes_retransmit=0 bytes_invalid=0 send_seq=3573 receive_seq=3573 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999215 adj=49997291 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=122166 bytes_read=3603626 bytes_retransmit=9 bytes_invalid=0 send_seq=16353 receive_seq=16353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997727 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66809 bytes_read=1253704 bytes_retransmit=9 bytes_invalid=0 send_seq=8531 receive_seq=8531 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997688 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21877 bytes_read=875843 bytes_retransmit=9 bytes_invalid=0 send_seq=3587 receive_seq=3587 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22363 bytes_read=67237 bytes_retransmit=9 bytes_invalid=0 send_seq=3574 receive_seq=3574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999456 Octopus_Pro_H723_V1.1: temp=31.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76455 bytes_read=1453261 bytes_retransmit=0 bytes_invalid=0 send_seq=8133 receive_seq=8133 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998688 coil_temp=17.8 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=42.7 th1: temp=43.5 th2: temp=47.1 th3: temp=45.1 sysload=0.15 cputime=261.416 memavail=7398684 print_time=3464.737 buffer_time=2.180 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 44 Hz
Stats 3441.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20080638 bytes_read=2651694 bytes_retransmit=9 bytes_invalid=0 send_seq=355448 receive_seq=355448 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=23 upcoming_bytes=0 freq=400015333 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21616 bytes_read=68592 bytes_retransmit=0 bytes_invalid=0 send_seq=3574 receive_seq=3574 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999214 adj=49997274 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=122172 bytes_read=3603726 bytes_retransmit=9 bytes_invalid=0 send_seq=16354 receive_seq=16354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997708 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66885 bytes_read=1256778 bytes_retransmit=9 bytes_invalid=0 send_seq=8542 receive_seq=8542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997645 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21883 bytes_read=876077 bytes_retransmit=9 bytes_invalid=0 send_seq=3588 receive_seq=3588 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999515 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22369 bytes_read=67253 bytes_retransmit=9 bytes_invalid=0 send_seq=3575 receive_seq=3575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999452 Octopus_Pro_H723_V1.1: temp=31.0 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76461 bytes_read=1453617 bytes_retransmit=0 bytes_invalid=0 send_seq=8134 receive_seq=8134 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998681 coil_temp=17.8 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=42.8 th1: temp=43.4 th2: temp=47.4 th3: temp=45.3 sysload=0.15 cputime=261.494 memavail=7398692 print_time=3465.656 buffer_time=2.099 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 45 Hz
Stats 3442.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20083657 bytes_read=2652339 bytes_retransmit=9 bytes_invalid=0 send_seq=355515 receive_seq=355515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015322 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21622 bytes_read=68608 bytes_retransmit=0 bytes_invalid=0 send_seq=3575 receive_seq=3575 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997294 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=122178 bytes_read=3603826 bytes_retransmit=9 bytes_invalid=0 send_seq=16355 receive_seq=16355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997734 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=66961 bytes_read=1259839 bytes_retransmit=9 bytes_invalid=0 send_seq=8553 receive_seq=8553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997659 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21889 bytes_read=876326 bytes_retransmit=9 bytes_invalid=0 send_seq=3589 receive_seq=3589 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22375 bytes_read=67280 bytes_retransmit=9 bytes_invalid=0 send_seq=3576 receive_seq=3576 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999456 Octopus_Pro_H723_V1.1: temp=30.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76467 bytes_read=1453973 bytes_retransmit=0 bytes_invalid=0 send_seq=8135 receive_seq=8135 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998708 coil_temp=17.8 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=42.7 th1: temp=43.3 th2: temp=47.4 th3: temp=45.2 sysload=0.15 cputime=261.579 memavail=7398692 print_time=3466.861 buffer_time=2.303 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 46 Hz
Stats 3443.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20085706 bytes_read=2652908 bytes_retransmit=9 bytes_invalid=0 send_seq=355561 receive_seq=355561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=0 freq=400015330 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21628 bytes_read=68624 bytes_retransmit=0 bytes_invalid=0 send_seq=3576 receive_seq=3576 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997299 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=122184 bytes_read=3603954 bytes_retransmit=9 bytes_invalid=0 send_seq=16356 receive_seq=16356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997828 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67037 bytes_read=1262926 bytes_retransmit=9 bytes_invalid=0 send_seq=8564 receive_seq=8564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997642 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21895 bytes_read=876620 bytes_retransmit=9 bytes_invalid=0 send_seq=3590 receive_seq=3590 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997707 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22381 bytes_read=67296 bytes_retransmit=9 bytes_invalid=0 send_seq=3577 receive_seq=3577 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999459 Octopus_Pro_H723_V1.1: temp=31.0 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76473 bytes_read=1454329 bytes_retransmit=0 bytes_invalid=0 send_seq=8136 receive_seq=8136 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998703 coil_temp=17.8 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=43.4 th1: temp=43.4 th2: temp=47.2 th3: temp=44.9 sysload=0.22 cputime=261.667 memavail=7399948 print_time=3467.754 buffer_time=2.196 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 47 Hz
Stats 3444.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20088258 bytes_read=2653458 bytes_retransmit=9 bytes_invalid=0 send_seq=355609 receive_seq=355609 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015312 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21634 bytes_read=68640 bytes_retransmit=0 bytes_invalid=0 send_seq=3577 receive_seq=3577 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997314 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=122190 bytes_read=3604054 bytes_retransmit=9 bytes_invalid=0 send_seq=16357 receive_seq=16357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997792 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67113 bytes_read=1265984 bytes_retransmit=9 bytes_invalid=0 send_seq=8575 receive_seq=8575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997613 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21901 bytes_read=876854 bytes_retransmit=9 bytes_invalid=0 send_seq=3591 receive_seq=3591 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997707 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22387 bytes_read=67312 bytes_retransmit=9 bytes_invalid=0 send_seq=3578 receive_seq=3578 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999458 Octopus_Pro_H723_V1.1: temp=30.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76479 bytes_read=1454685 bytes_retransmit=0 bytes_invalid=0 send_seq=8137 receive_seq=8137 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998698 coil_temp=17.8 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=42.8 th1: temp=43.6 th2: temp=47.6 th3: temp=45.3 sysload=0.22 cputime=261.745 memavail=7400064 print_time=3468.673 buffer_time=2.114 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 48 Hz
Stats 3445.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=20090386 bytes_read=2654048 bytes_retransmit=9 bytes_invalid=0 send_seq=355662 receive_seq=355662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=47 upcoming_bytes=0 freq=400015300 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21640 bytes_read=68655 bytes_retransmit=0 bytes_invalid=0 send_seq=3578 receive_seq=3578 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999215 adj=49997339 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122196 bytes_read=3604168 bytes_retransmit=9 bytes_invalid=0 send_seq=16358 receive_seq=16358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997810 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67189 bytes_read=1269040 bytes_retransmit=9 bytes_invalid=0 send_seq=8586 receive_seq=8586 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997640 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21907 bytes_read=877088 bytes_retransmit=9 bytes_invalid=0 send_seq=3592 receive_seq=3592 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997753 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22393 bytes_read=67328 bytes_retransmit=9 bytes_invalid=0 send_seq=3579 receive_seq=3579 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999466 Octopus_Pro_H723_V1.1: temp=30.7 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76485 bytes_read=1455041 bytes_retransmit=0 bytes_invalid=0 send_seq=8138 receive_seq=8138 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998714 coil_temp=17.8 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=42.8 th1: temp=43.7 th2: temp=47.2 th3: temp=45.3 sysload=0.22 cputime=261.829 memavail=7399824 print_time=3469.559 buffer_time=2.000 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 49 Hz
Stats 3446.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=20093588 bytes_read=2654727 bytes_retransmit=9 bytes_invalid=0 send_seq=355731 receive_seq=355731 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=46 upcoming_bytes=0 freq=400015311 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21646 bytes_read=68683 bytes_retransmit=0 bytes_invalid=0 send_seq=3579 receive_seq=3579 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999215 adj=49997351 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122202 bytes_read=3604296 bytes_retransmit=9 bytes_invalid=0 send_seq=16359 receive_seq=16359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997866 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67265 bytes_read=1272145 bytes_retransmit=9 bytes_invalid=0 send_seq=8597 receive_seq=8597 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997648 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21913 bytes_read=877382 bytes_retransmit=9 bytes_invalid=0 send_seq=3593 receive_seq=3593 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997755 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22399 bytes_read=67344 bytes_retransmit=9 bytes_invalid=0 send_seq=3580 receive_seq=3580 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999468 Octopus_Pro_H723_V1.1: temp=30.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76491 bytes_read=1455397 bytes_retransmit=0 bytes_invalid=0 send_seq=8139 receive_seq=8139 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998730 coil_temp=17.8 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=43.1 th1: temp=43.7 th2: temp=47.3 th3: temp=45.4 sysload=0.22 cputime=261.920 memavail=7398844 print_time=3470.779 buffer_time=2.220 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 50 Hz
Stats 3447.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=20096319 bytes_read=2655347 bytes_retransmit=9 bytes_invalid=0 send_seq=355793 receive_seq=355793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015295 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21652 bytes_read=68698 bytes_retransmit=0 bytes_invalid=0 send_seq=3580 receive_seq=3580 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999215 adj=49997318 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122208 bytes_read=3604396 bytes_retransmit=9 bytes_invalid=0 send_seq=16360 receive_seq=16360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997794 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67341 bytes_read=1275202 bytes_retransmit=9 bytes_invalid=0 send_seq=8608 receive_seq=8608 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997599 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21919 bytes_read=877631 bytes_retransmit=9 bytes_invalid=0 send_seq=3594 receive_seq=3594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997708 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22405 bytes_read=67371 bytes_retransmit=9 bytes_invalid=0 send_seq=3581 receive_seq=3581 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999459 Octopus_Pro_H723_V1.1: temp=30.7 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76497 bytes_read=1455730 bytes_retransmit=0 bytes_invalid=0 send_seq=8140 receive_seq=8140 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998714 coil_temp=17.8 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=43.0 th1: temp=43.7 th2: temp=47.3 th3: temp=45.3 sysload=0.22 cputime=262.001 memavail=7398844 print_time=3471.683 buffer_time=2.123 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 51 Hz
Stats 3448.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=20098432 bytes_read=2655917 bytes_retransmit=9 bytes_invalid=0 send_seq=355845 receive_seq=355845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=0 freq=400015290 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21658 bytes_read=68713 bytes_retransmit=0 bytes_invalid=0 send_seq=3581 receive_seq=3581 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999214 adj=49997334 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122214 bytes_read=3604496 bytes_retransmit=9 bytes_invalid=0 send_seq=16361 receive_seq=16361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997821 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67417 bytes_read=1278318 bytes_retransmit=9 bytes_invalid=0 send_seq=8619 receive_seq=8619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997629 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21925 bytes_read=877865 bytes_retransmit=9 bytes_invalid=0 send_seq=3595 receive_seq=3595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997724 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22411 bytes_read=67387 bytes_retransmit=9 bytes_invalid=0 send_seq=3582 receive_seq=3582 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999464 Octopus_Pro_H723_V1.1: temp=30.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76503 bytes_read=1456075 bytes_retransmit=0 bytes_invalid=0 send_seq=8141 receive_seq=8141 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998719 coil_temp=17.8 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=43.0 th1: temp=43.8 th2: temp=47.5 th3: temp=45.3 sysload=0.20 cputime=262.081 memavail=7398592 print_time=3472.570 buffer_time=2.010 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 52 Hz
Stats 3449.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=20101668 bytes_read=2656606 bytes_retransmit=9 bytes_invalid=0 send_seq=355915 receive_seq=355915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=46 upcoming_bytes=0 freq=400015290 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21664 bytes_read=68728 bytes_retransmit=0 bytes_invalid=0 send_seq=3582 receive_seq=3582 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997330 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122220 bytes_read=3604624 bytes_retransmit=9 bytes_invalid=0 send_seq=16362 receive_seq=16362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997918 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67493 bytes_read=1281403 bytes_retransmit=9 bytes_invalid=0 send_seq=8630 receive_seq=8630 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997620 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21931 bytes_read=878159 bytes_retransmit=9 bytes_invalid=0 send_seq=3596 receive_seq=3596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997726 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22417 bytes_read=67403 bytes_retransmit=9 bytes_invalid=0 send_seq=3583 receive_seq=3583 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999464 Octopus_Pro_H723_V1.1: temp=30.6 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76509 bytes_read=1456419 bytes_retransmit=0 bytes_invalid=0 send_seq=8142 receive_seq=8142 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998734 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=43.0 th1: temp=43.5 th2: temp=47.5 th3: temp=45.3 sysload=0.20 cputime=262.170 memavail=7398596 print_time=3473.783 buffer_time=2.222 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 53 Hz
Stats 3450.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20104462 bytes_read=2657236 bytes_retransmit=9 bytes_invalid=0 send_seq=355976 receive_seq=355976 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=0 freq=400015418 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21670 bytes_read=68744 bytes_retransmit=0 bytes_invalid=0 send_seq=3583 receive_seq=3583 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997309 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122226 bytes_read=3604738 bytes_retransmit=9 bytes_invalid=0 send_seq=16363 receive_seq=16363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997949 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67569 bytes_read=1284460 bytes_retransmit=9 bytes_invalid=0 send_seq=8641 receive_seq=8641 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997684 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21937 bytes_read=878393 bytes_retransmit=9 bytes_invalid=0 send_seq=3597 receive_seq=3597 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997714 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22423 bytes_read=67419 bytes_retransmit=9 bytes_invalid=0 send_seq=3584 receive_seq=3584 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999461 Octopus_Pro_H723_V1.1: temp=30.5 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76515 bytes_read=1456764 bytes_retransmit=0 bytes_invalid=0 send_seq=8143 receive_seq=8143 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998719 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=43.1 th1: temp=43.8 th2: temp=47.5 th3: temp=45.4 sysload=0.20 cputime=262.252 memavail=7398596 print_time=3474.682 buffer_time=2.122 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 54 Hz
Stats 3451.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20106758 bytes_read=2657821 bytes_retransmit=9 bytes_invalid=0 send_seq=356031 receive_seq=356031 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015414 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=21676 bytes_read=68773 bytes_retransmit=0 bytes_invalid=0 send_seq=3584 receive_seq=3584 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997102 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122232 bytes_read=3604838 bytes_retransmit=9 bytes_invalid=0 send_seq=16364 receive_seq=16364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997745 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67645 bytes_read=1287533 bytes_retransmit=9 bytes_invalid=0 send_seq=8652 receive_seq=8652 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997400 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21943 bytes_read=878627 bytes_retransmit=9 bytes_invalid=0 send_seq=3598 receive_seq=3598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997512 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22429 bytes_read=67435 bytes_retransmit=9 bytes_invalid=0 send_seq=3585 receive_seq=3585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999411 Octopus_Pro_H723_V1.1: temp=30.4 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76521 bytes_read=1457109 bytes_retransmit=0 bytes_invalid=0 send_seq=8144 receive_seq=8144 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998582 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=43.2 th1: temp=43.8 th2: temp=47.6 th3: temp=45.5 sysload=0.20 cputime=262.332 memavail=7398596 print_time=3475.594 buffer_time=2.033 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 55 Hz
Stats 3452.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20110042 bytes_read=2658520 bytes_retransmit=9 bytes_invalid=0 send_seq=356103 receive_seq=356103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=400015397 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=21682 bytes_read=68789 bytes_retransmit=0 bytes_invalid=0 send_seq=3585 receive_seq=3585 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997128 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122238 bytes_read=3604966 bytes_retransmit=9 bytes_invalid=0 send_seq=16365 receive_seq=16365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997726 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67721 bytes_read=1290621 bytes_retransmit=9 bytes_invalid=0 send_seq=8663 receive_seq=8663 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997417 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=21949 bytes_read=878936 bytes_retransmit=9 bytes_invalid=0 send_seq=3599 receive_seq=3599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997558 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22435 bytes_read=67462 bytes_retransmit=9 bytes_invalid=0 send_seq=3586 receive_seq=3586 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999419 Octopus_Pro_H723_V1.1: temp=30.7 EBB42_Gen2_v1.0_T0: temp=31.1 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76527 bytes_read=1457454 bytes_retransmit=0 bytes_invalid=0 send_seq=8145 receive_seq=8145 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998606 coil_temp=17.7 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=43.0 th1: temp=44.1 th2: temp=47.9 th3: temp=45.5 sysload=0.20 cputime=262.423 memavail=7398596 print_time=3476.799 buffer_time=2.238 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 56 Hz
Stats 3453.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20112933 bytes_read=2659155 bytes_retransmit=9 bytes_invalid=0 send_seq=356168 receive_seq=356168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015385 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=21688 bytes_read=68805 bytes_retransmit=0 bytes_invalid=0 send_seq=3586 receive_seq=3586 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997199 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122244 bytes_read=3605066 bytes_retransmit=9 bytes_invalid=0 send_seq=16366 receive_seq=16366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997738 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67797 bytes_read=1293679 bytes_retransmit=9 bytes_invalid=0 send_seq=8674 receive_seq=8674 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997487 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=21955 bytes_read=879170 bytes_retransmit=9 bytes_invalid=0 send_seq=3600 receive_seq=3600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997612 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22441 bytes_read=67478 bytes_retransmit=9 bytes_invalid=0 send_seq=3587 receive_seq=3587 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999436 Octopus_Pro_H723_V1.1: temp=30.5 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76533 bytes_read=1457799 bytes_retransmit=0 bytes_invalid=0 send_seq=8146 receive_seq=8146 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998655 coil_temp=17.7 refs=0 mcu_temp=20.90 supply_voltage=3.012 th0: temp=43.1 th1: temp=43.9 th2: temp=47.8 th3: temp=45.5 sysload=0.18 cputime=262.505 memavail=7398596 print_time=3477.699 buffer_time=2.138 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 57 Hz
Stats 3454.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20115245 bytes_read=2659740 bytes_retransmit=9 bytes_invalid=0 send_seq=356223 receive_seq=356223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=0 freq=400015382 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=21694 bytes_read=68821 bytes_retransmit=0 bytes_invalid=0 send_seq=3587 receive_seq=3587 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997221 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122250 bytes_read=3605166 bytes_retransmit=9 bytes_invalid=0 send_seq=16367 receive_seq=16367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997748 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67866 bytes_read=1296713 bytes_retransmit=9 bytes_invalid=0 send_seq=8684 receive_seq=8684 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=21961 bytes_read=879404 bytes_retransmit=9 bytes_invalid=0 send_seq=3601 receive_seq=3601 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997630 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22447 bytes_read=67494 bytes_retransmit=9 bytes_invalid=0 send_seq=3588 receive_seq=3588 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999442 Octopus_Pro_H723_V1.1: temp=30.5 EBB42_Gen2_v1.0_T0: temp=31.1 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76539 bytes_read=1458144 bytes_retransmit=0 bytes_invalid=0 send_seq=8147 receive_seq=8147 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998662 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=43.1 th1: temp=44.0 th2: temp=47.6 th3: temp=45.6 sysload=0.18 cputime=262.586 memavail=7398596 print_time=3478.620 buffer_time=2.058 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 58 Hz
Stats 3455.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20118724 bytes_read=2660469 bytes_retransmit=9 bytes_invalid=0 send_seq=356298 receive_seq=356298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015370 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=21700 bytes_read=68837 bytes_retransmit=0 bytes_invalid=0 send_seq=3588 receive_seq=3588 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997235 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122256 bytes_read=3605308 bytes_retransmit=9 bytes_invalid=0 send_seq=16368 receive_seq=16368 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997730 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=67942 bytes_read=1299800 bytes_retransmit=9 bytes_invalid=0 send_seq=8695 receive_seq=8695 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=21967 bytes_read=879698 bytes_retransmit=9 bytes_invalid=0 send_seq=3602 receive_seq=3602 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22453 bytes_read=67510 bytes_retransmit=9 bytes_invalid=0 send_seq=3589 receive_seq=3589 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999446 Octopus_Pro_H723_V1.1: temp=30.3 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76545 bytes_read=1458491 bytes_retransmit=0 bytes_invalid=0 send_seq=8148 receive_seq=8148 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998664 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=42.9 th1: temp=44.0 th2: temp=47.2 th3: temp=45.7 sysload=0.18 cputime=262.678 memavail=7398596 print_time=3479.827 buffer_time=2.265 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 59 Hz
Stats 3456.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20121575 bytes_read=2661094 bytes_retransmit=9 bytes_invalid=0 send_seq=356361 receive_seq=356361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015357 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21706 bytes_read=68866 bytes_retransmit=0 bytes_invalid=0 send_seq=3589 receive_seq=3589 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997255 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122262 bytes_read=3605408 bytes_retransmit=9 bytes_invalid=0 send_seq=16369 receive_seq=16369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997754 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68018 bytes_read=1302932 bytes_retransmit=9 bytes_invalid=0 send_seq=8706 receive_seq=8706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997568 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=21973 bytes_read=879932 bytes_retransmit=9 bytes_invalid=0 send_seq=3603 receive_seq=3603 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22459 bytes_read=67526 bytes_retransmit=9 bytes_invalid=0 send_seq=3590 receive_seq=3590 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999455 Octopus_Pro_H723_V1.1: temp=30.5 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76551 bytes_read=1458847 bytes_retransmit=0 bytes_invalid=0 send_seq=8149 receive_seq=8149 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998675 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=43.4 th1: temp=44.1 th2: temp=47.6 th3: temp=45.6 sysload=0.18 cputime=262.765 memavail=7397868 print_time=3480.710 buffer_time=2.148 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 60 Hz
Stats 3457.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20124019 bytes_read=2661684 bytes_retransmit=9 bytes_invalid=0 send_seq=356418 receive_seq=356418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015349 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21712 bytes_read=68882 bytes_retransmit=0 bytes_invalid=0 send_seq=3590 receive_seq=3590 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997271 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122268 bytes_read=3605508 bytes_retransmit=9 bytes_invalid=0 send_seq=16370 receive_seq=16370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997853 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68094 bytes_read=1305992 bytes_retransmit=9 bytes_invalid=0 send_seq=8717 receive_seq=8717 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997583 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21979 bytes_read=880181 bytes_retransmit=9 bytes_invalid=0 send_seq=3604 receive_seq=3604 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997677 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22465 bytes_read=67553 bytes_retransmit=9 bytes_invalid=0 send_seq=3591 receive_seq=3591 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999458 Octopus_Pro_H723_V1.1: temp=30.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76557 bytes_read=1459203 bytes_retransmit=0 bytes_invalid=0 send_seq=8150 receive_seq=8150 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998686 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.1 th2: temp=47.7 th3: temp=45.6 sysload=0.18 cputime=262.850 memavail=7397868 print_time=3481.639 buffer_time=2.077 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 61 Hz
Stats 3458.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20127496 bytes_read=2662393 bytes_retransmit=9 bytes_invalid=0 send_seq=356492 receive_seq=356492 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=400015339 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21718 bytes_read=68898 bytes_retransmit=0 bytes_invalid=0 send_seq=3591 receive_seq=3591 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997298 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122274 bytes_read=3605636 bytes_retransmit=9 bytes_invalid=0 send_seq=16371 receive_seq=16371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997823 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68170 bytes_read=1309079 bytes_retransmit=9 bytes_invalid=0 send_seq=8728 receive_seq=8728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997719 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21985 bytes_read=880475 bytes_retransmit=9 bytes_invalid=0 send_seq=3605 receive_seq=3605 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997692 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22471 bytes_read=67569 bytes_retransmit=9 bytes_invalid=0 send_seq=3592 receive_seq=3592 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999462 Octopus_Pro_H723_V1.1: temp=30.5 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76563 bytes_read=1459559 bytes_retransmit=0 bytes_invalid=0 send_seq=8151 receive_seq=8151 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998694 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=43.6 th1: temp=44.0 th2: temp=47.5 th3: temp=45.6 sysload=0.17 cputime=262.945 memavail=7397872 print_time=3482.839 buffer_time=2.277 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=19.1 pwm=0.000
Testing frequency 62 Hz
Stats 3459.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20130455 bytes_read=2663033 bytes_retransmit=9 bytes_invalid=0 send_seq=356558 receive_seq=356558 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015327 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21724 bytes_read=68914 bytes_retransmit=0 bytes_invalid=0 send_seq=3592 receive_seq=3592 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997327 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122280 bytes_read=3605736 bytes_retransmit=9 bytes_invalid=0 send_seq=16372 receive_seq=16372 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997798 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68246 bytes_read=1312135 bytes_retransmit=9 bytes_invalid=0 send_seq=8739 receive_seq=8739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997681 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21991 bytes_read=880709 bytes_retransmit=9 bytes_invalid=0 send_seq=3606 receive_seq=3606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999517 adj=47997701 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22477 bytes_read=67585 bytes_retransmit=9 bytes_invalid=0 send_seq=3593 receive_seq=3593 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999462 Octopus_Pro_H723_V1.1: temp=30.4 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76569 bytes_read=1459915 bytes_retransmit=0 bytes_invalid=0 send_seq=8152 receive_seq=8152 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998693 coil_temp=17.7 refs=0 mcu_temp=20.89 supply_voltage=3.012 th0: temp=43.5 th1: temp=43.9 th2: temp=47.6 th3: temp=45.7 sysload=0.17 cputime=263.030 memavail=7397872 print_time=3483.728 buffer_time=2.165 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 63 Hz
Stats 3460.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20132992 bytes_read=2663654 bytes_retransmit=9 bytes_invalid=0 send_seq=356617 receive_seq=356617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=0 freq=400015347 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21730 bytes_read=68930 bytes_retransmit=0 bytes_invalid=0 send_seq=3593 receive_seq=3593 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997346 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122286 bytes_read=3605850 bytes_retransmit=9 bytes_invalid=0 send_seq=16373 receive_seq=16373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997795 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68322 bytes_read=1315194 bytes_retransmit=9 bytes_invalid=0 send_seq=8750 receive_seq=8750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997677 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=21997 bytes_read=880943 bytes_retransmit=9 bytes_invalid=0 send_seq=3607 receive_seq=3607 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999516 adj=47997712 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22483 bytes_read=67601 bytes_retransmit=9 bytes_invalid=0 send_seq=3594 receive_seq=3594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999466 Octopus_Pro_H723_V1.1: temp=30.4 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76575 bytes_read=1460271 bytes_retransmit=0 bytes_invalid=0 send_seq=8153 receive_seq=8153 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998701 coil_temp=17.7 refs=0 mcu_temp=20.88 supply_voltage=3.012 th0: temp=43.4 th1: temp=44.0 th2: temp=47.7 th3: temp=45.6 sysload=0.17 cputime=263.128 memavail=7398636 print_time=3484.656 buffer_time=2.093 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 64 Hz
Stats 3461.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20136575 bytes_read=2664368 bytes_retransmit=9 bytes_invalid=0 send_seq=356692 receive_seq=356692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=0 freq=400015348 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21736 bytes_read=68959 bytes_retransmit=0 bytes_invalid=0 send_seq=3594 receive_seq=3594 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997319 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122292 bytes_read=3605978 bytes_retransmit=9 bytes_invalid=0 send_seq=16374 receive_seq=16374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997724 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68398 bytes_read=1318295 bytes_retransmit=9 bytes_invalid=0 send_seq=8761 receive_seq=8761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997630 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22003 bytes_read=881237 bytes_retransmit=9 bytes_invalid=0 send_seq=3608 receive_seq=3608 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22489 bytes_read=67617 bytes_retransmit=9 bytes_invalid=0 send_seq=3595 receive_seq=3595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999458 Octopus_Pro_H723_V1.1: temp=30.4 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=30.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76581 bytes_read=1460627 bytes_retransmit=0 bytes_invalid=0 send_seq=8154 receive_seq=8154 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998693 coil_temp=17.7 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=43.0 th1: temp=44.2 th2: temp=47.7 th3: temp=45.8 sysload=0.17 cputime=263.225 memavail=7398636 print_time=3485.863 buffer_time=2.299 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 65 Hz
Stats 3462.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20139525 bytes_read=2664998 bytes_retransmit=9 bytes_invalid=0 send_seq=356756 receive_seq=356756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=0 freq=400015362 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21742 bytes_read=68975 bytes_retransmit=0 bytes_invalid=0 send_seq=3595 receive_seq=3595 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997311 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122298 bytes_read=3606078 bytes_retransmit=9 bytes_invalid=0 send_seq=16375 receive_seq=16375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997711 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68474 bytes_read=1321352 bytes_retransmit=9 bytes_invalid=0 send_seq=8772 receive_seq=8772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997602 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22009 bytes_read=881486 bytes_retransmit=9 bytes_invalid=0 send_seq=3609 receive_seq=3609 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22495 bytes_read=67644 bytes_retransmit=9 bytes_invalid=0 send_seq=3596 receive_seq=3596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999465 Octopus_Pro_H723_V1.1: temp=30.4 EBB42_Gen2_v1.0_T0: temp=31.1 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76587 bytes_read=1460983 bytes_retransmit=0 bytes_invalid=0 send_seq=8155 receive_seq=8155 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998685 coil_temp=17.7 refs=0 mcu_temp=20.87 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.3 th2: temp=47.8 th3: temp=45.7 sysload=0.17 cputime=263.309 memavail=7398636 print_time=3486.730 buffer_time=2.166 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 66 Hz
Stats 3463.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20142194 bytes_read=2665598 bytes_retransmit=9 bytes_invalid=0 send_seq=356814 receive_seq=356814 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015399 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21748 bytes_read=68991 bytes_retransmit=0 bytes_invalid=0 send_seq=3596 receive_seq=3596 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997287 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122304 bytes_read=3606178 bytes_retransmit=9 bytes_invalid=0 send_seq=16376 receive_seq=16376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997692 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68550 bytes_read=1324413 bytes_retransmit=9 bytes_invalid=0 send_seq=8783 receive_seq=8783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22015 bytes_read=881720 bytes_retransmit=9 bytes_invalid=0 send_seq=3610 receive_seq=3610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22501 bytes_read=67660 bytes_retransmit=9 bytes_invalid=0 send_seq=3597 receive_seq=3597 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999458 Octopus_Pro_H723_V1.1: temp=30.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76593 bytes_read=1461339 bytes_retransmit=0 bytes_invalid=0 send_seq=8156 receive_seq=8156 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998688 coil_temp=17.7 refs=0 mcu_temp=20.86 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.3 th2: temp=47.9 th3: temp=45.9 sysload=0.15 cputime=263.394 memavail=7398412 print_time=3487.662 buffer_time=2.098 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 67 Hz
Stats 3464.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20145888 bytes_read=2666307 bytes_retransmit=9 bytes_invalid=0 send_seq=356888 receive_seq=356888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015463 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21754 bytes_read=69007 bytes_retransmit=0 bytes_invalid=0 send_seq=3597 receive_seq=3597 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997223 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122310 bytes_read=3606306 bytes_retransmit=9 bytes_invalid=0 send_seq=16377 receive_seq=16377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997625 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68626 bytes_read=1327555 bytes_retransmit=9 bytes_invalid=0 send_seq=8794 receive_seq=8794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997482 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22021 bytes_read=882014 bytes_retransmit=9 bytes_invalid=0 send_seq=3611 receive_seq=3611 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22507 bytes_read=67676 bytes_retransmit=9 bytes_invalid=0 send_seq=3598 receive_seq=3598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999442 Octopus_Pro_H723_V1.1: temp=30.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76599 bytes_read=1461695 bytes_retransmit=0 bytes_invalid=0 send_seq=8157 receive_seq=8157 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998659 coil_temp=17.7 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=43.3 th1: temp=44.3 th2: temp=47.9 th3: temp=45.7 sysload=0.15 cputime=263.490 memavail=7398412 print_time=3488.873 buffer_time=2.308 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 68 Hz
Stats 3465.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20148808 bytes_read=2666933 bytes_retransmit=9 bytes_invalid=0 send_seq=356948 receive_seq=356948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=0 freq=400015513 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21760 bytes_read=69023 bytes_retransmit=0 bytes_invalid=0 send_seq=3598 receive_seq=3598 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997150 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122316 bytes_read=3606420 bytes_retransmit=9 bytes_invalid=0 send_seq=16378 receive_seq=16378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997529 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68702 bytes_read=1330614 bytes_retransmit=9 bytes_invalid=0 send_seq=8805 receive_seq=8805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997465 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22027 bytes_read=882248 bytes_retransmit=9 bytes_invalid=0 send_seq=3612 receive_seq=3612 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997544 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22513 bytes_read=67692 bytes_retransmit=9 bytes_invalid=0 send_seq=3599 receive_seq=3599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999425 Octopus_Pro_H723_V1.1: temp=30.4 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76605 bytes_read=1462051 bytes_retransmit=0 bytes_invalid=0 send_seq=8158 receive_seq=8158 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998613 coil_temp=17.7 refs=0 mcu_temp=20.85 supply_voltage=3.012 th0: temp=43.6 th1: temp=44.6 th2: temp=48.1 th3: temp=45.5 sysload=0.15 cputime=263.575 memavail=7398412 print_time=3489.742 buffer_time=2.176 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 69 Hz
Stats 3466.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20151597 bytes_read=2667553 bytes_retransmit=9 bytes_invalid=0 send_seq=357010 receive_seq=357010 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015603 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21766 bytes_read=69052 bytes_retransmit=0 bytes_invalid=0 send_seq=3599 receive_seq=3599 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997085 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122322 bytes_read=3606518 bytes_retransmit=9 bytes_invalid=0 send_seq=16379 receive_seq=16379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997451 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68778 bytes_read=1333685 bytes_retransmit=9 bytes_invalid=0 send_seq=8816 receive_seq=8816 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997359 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22033 bytes_read=882474 bytes_retransmit=9 bytes_invalid=0 send_seq=3613 receive_seq=3613 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997485 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22519 bytes_read=67708 bytes_retransmit=9 bytes_invalid=0 send_seq=3600 receive_seq=3600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999411 Octopus_Pro_H723_V1.1: temp=30.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76611 bytes_read=1462407 bytes_retransmit=0 bytes_invalid=0 send_seq=8159 receive_seq=8159 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998569 coil_temp=17.7 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=43.6 th1: temp=44.3 th2: temp=48.0 th3: temp=46.0 sysload=0.15 cputime=263.663 memavail=7397692 print_time=3490.679 buffer_time=2.113 print_stall=0 extruder: target=0 temp=20.0 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 70 Hz
Stats 3467.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20155320 bytes_read=2668278 bytes_retransmit=9 bytes_invalid=0 send_seq=357088 receive_seq=357088 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=0 freq=400015638 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21772 bytes_read=69068 bytes_retransmit=0 bytes_invalid=0 send_seq=3600 receive_seq=3600 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49996982 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122328 bytes_read=3606637 bytes_retransmit=9 bytes_invalid=0 send_seq=16380 receive_seq=16380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997296 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68854 bytes_read=1336751 bytes_retransmit=9 bytes_invalid=0 send_seq=8827 receive_seq=8827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997195 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22039 bytes_read=882763 bytes_retransmit=9 bytes_invalid=0 send_seq=3614 receive_seq=3614 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997374 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22525 bytes_read=67735 bytes_retransmit=9 bytes_invalid=0 send_seq=3601 receive_seq=3601 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999382 Octopus_Pro_H723_V1.1: temp=30.2 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=30.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76617 bytes_read=1462763 bytes_retransmit=0 bytes_invalid=0 send_seq=8160 receive_seq=8160 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998484 coil_temp=17.7 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=43.3 th1: temp=44.3 th2: temp=48.0 th3: temp=46.0 sysload=0.15 cputime=263.759 memavail=7397692 print_time=3491.871 buffer_time=2.304 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 71 Hz
Stats 3468.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20158448 bytes_read=2668925 bytes_retransmit=9 bytes_invalid=0 send_seq=357156 receive_seq=357156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=0 freq=400015630 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21778 bytes_read=69084 bytes_retransmit=0 bytes_invalid=0 send_seq=3601 receive_seq=3601 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997006 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122334 bytes_read=3606730 bytes_retransmit=9 bytes_invalid=0 send_seq=16381 receive_seq=16381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997337 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68930 bytes_read=1339791 bytes_retransmit=9 bytes_invalid=0 send_seq=8838 receive_seq=8838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997217 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22045 bytes_read=882981 bytes_retransmit=9 bytes_invalid=0 send_seq=3615 receive_seq=3615 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997403 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22531 bytes_read=67751 bytes_retransmit=9 bytes_invalid=0 send_seq=3602 receive_seq=3602 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999388 Octopus_Pro_H723_V1.1: temp=30.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76623 bytes_read=1463119 bytes_retransmit=0 bytes_invalid=0 send_seq=8161 receive_seq=8161 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998507 coil_temp=17.7 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=43.4 th1: temp=44.4 th2: temp=47.7 th3: temp=45.8 sysload=0.14 cputime=263.846 memavail=7397692 print_time=3492.756 buffer_time=2.188 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 72 Hz
Stats 3469.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20161320 bytes_read=2669555 bytes_retransmit=9 bytes_invalid=0 send_seq=357220 receive_seq=357220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=0 freq=400015626 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21784 bytes_read=69100 bytes_retransmit=0 bytes_invalid=0 send_seq=3602 receive_seq=3602 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997062 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122340 bytes_read=3606823 bytes_retransmit=9 bytes_invalid=0 send_seq=16382 receive_seq=16382 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997383 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=68999 bytes_read=1342808 bytes_retransmit=9 bytes_invalid=0 send_seq=8848 receive_seq=8848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997272 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22051 bytes_read=883199 bytes_retransmit=9 bytes_invalid=0 send_seq=3616 receive_seq=3616 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997440 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22537 bytes_read=67767 bytes_retransmit=9 bytes_invalid=0 send_seq=3603 receive_seq=3603 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999396 Octopus_Pro_H723_V1.1: temp=30.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76629 bytes_read=1463475 bytes_retransmit=0 bytes_invalid=0 send_seq=8162 receive_seq=8162 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998527 coil_temp=17.7 refs=0 mcu_temp=20.84 supply_voltage=3.012 th0: temp=43.5 th1: temp=44.3 th2: temp=47.9 th3: temp=45.9 sysload=0.14 cputime=263.933 memavail=7397692 print_time=3493.696 buffer_time=2.128 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 73 Hz
Stats 3470.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20164419 bytes_read=2670250 bytes_retransmit=9 bytes_invalid=0 send_seq=357288 receive_seq=357288 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015616 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21790 bytes_read=69116 bytes_retransmit=0 bytes_invalid=0 send_seq=3603 receive_seq=3603 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997086 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=122346 bytes_read=3606958 bytes_retransmit=9 bytes_invalid=0 send_seq=16383 receive_seq=16383 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997459 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69075 bytes_read=1345875 bytes_retransmit=9 bytes_invalid=0 send_seq=8859 receive_seq=8859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997303 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22057 bytes_read=883473 bytes_retransmit=9 bytes_invalid=0 send_seq=3617 receive_seq=3617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997474 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22543 bytes_read=67783 bytes_retransmit=9 bytes_invalid=0 send_seq=3604 receive_seq=3604 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999413 Octopus_Pro_H723_V1.1: temp=30.2 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76635 bytes_read=1463831 bytes_retransmit=0 bytes_invalid=0 send_seq=8163 receive_seq=8163 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998552 coil_temp=17.7 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=43.9 th1: temp=44.5 th2: temp=47.9 th3: temp=46.1 sysload=0.14 cputime=264.022 memavail=7397692 print_time=3494.569 buffer_time=2.001 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 74 Hz
Stats 3471.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20168332 bytes_read=2670965 bytes_retransmit=9 bytes_invalid=0 send_seq=357369 receive_seq=357369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=23 upcoming_bytes=0 freq=400015603 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21796 bytes_read=69145 bytes_retransmit=0 bytes_invalid=0 send_seq=3604 receive_seq=3604 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997111 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=122352 bytes_read=3607058 bytes_retransmit=9 bytes_invalid=0 send_seq=16384 receive_seq=16384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997487 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69151 bytes_read=1349006 bytes_retransmit=9 bytes_invalid=0 send_seq=8870 receive_seq=8870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997333 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22063 bytes_read=883695 bytes_retransmit=9 bytes_invalid=0 send_seq=3618 receive_seq=3618 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997508 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22549 bytes_read=67799 bytes_retransmit=9 bytes_invalid=0 send_seq=3605 receive_seq=3605 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999421 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76641 bytes_read=1464187 bytes_retransmit=0 bytes_invalid=0 send_seq=8164 receive_seq=8164 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998595 coil_temp=17.7 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=43.2 th1: temp=44.2 th2: temp=48.2 th3: temp=45.9 sysload=0.14 cputime=264.190 memavail=7397692 print_time=3495.776 buffer_time=2.207 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 75 Hz
Stats 3472.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20171325 bytes_read=2671605 bytes_retransmit=9 bytes_invalid=0 send_seq=357435 receive_seq=357435 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=0 freq=400015589 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21802 bytes_read=69161 bytes_retransmit=0 bytes_invalid=0 send_seq=3605 receive_seq=3605 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997178 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=122358 bytes_read=3607158 bytes_retransmit=9 bytes_invalid=0 send_seq=16385 receive_seq=16385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997563 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69227 bytes_read=1352063 bytes_retransmit=9 bytes_invalid=0 send_seq=8881 receive_seq=8881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997434 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22069 bytes_read=883941 bytes_retransmit=9 bytes_invalid=0 send_seq=3619 receive_seq=3619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997578 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22555 bytes_read=67826 bytes_retransmit=9 bytes_invalid=0 send_seq=3606 receive_seq=3606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999432 Octopus_Pro_H723_V1.1: temp=30.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76647 bytes_read=1464543 bytes_retransmit=0 bytes_invalid=0 send_seq=8165 receive_seq=8165 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998620 coil_temp=17.7 refs=0 mcu_temp=20.83 supply_voltage=3.012 th0: temp=43.4 th1: temp=44.5 th2: temp=48.1 th3: temp=45.8 sysload=0.14 cputime=264.279 memavail=7397692 print_time=3496.702 buffer_time=2.133 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 76 Hz
Stats 3473.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20174345 bytes_read=2672274 bytes_retransmit=9 bytes_invalid=0 send_seq=357501 receive_seq=357501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=0 freq=400015577 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21808 bytes_read=69177 bytes_retransmit=0 bytes_invalid=0 send_seq=3606 receive_seq=3606 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997215 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=122364 bytes_read=3607286 bytes_retransmit=9 bytes_invalid=0 send_seq=16386 receive_seq=16386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997620 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69296 bytes_read=1355127 bytes_retransmit=9 bytes_invalid=0 send_seq=8891 receive_seq=8891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997462 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22075 bytes_read=884235 bytes_retransmit=9 bytes_invalid=0 send_seq=3620 receive_seq=3620 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997612 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22561 bytes_read=67842 bytes_retransmit=9 bytes_invalid=0 send_seq=3607 receive_seq=3607 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999438 Octopus_Pro_H723_V1.1: temp=30.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76653 bytes_read=1464899 bytes_retransmit=0 bytes_invalid=0 send_seq=8166 receive_seq=8166 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998633 coil_temp=17.7 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=43.8 th1: temp=44.4 th2: temp=48.0 th3: temp=46.0 sysload=0.13 cputime=264.365 memavail=7397692 print_time=3497.577 buffer_time=2.007 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 77 Hz
Stats 3474.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20178331 bytes_read=2672999 bytes_retransmit=9 bytes_invalid=0 send_seq=357584 receive_seq=357584 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=23 upcoming_bytes=0 freq=400015565 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21814 bytes_read=69193 bytes_retransmit=0 bytes_invalid=0 send_seq=3607 receive_seq=3607 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997243 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=122370 bytes_read=3607386 bytes_retransmit=9 bytes_invalid=0 send_seq=16387 receive_seq=16387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997637 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69372 bytes_read=1358185 bytes_retransmit=9 bytes_invalid=0 send_seq=8902 receive_seq=8902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997481 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22081 bytes_read=884469 bytes_retransmit=9 bytes_invalid=0 send_seq=3621 receive_seq=3621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22567 bytes_read=67858 bytes_retransmit=9 bytes_invalid=0 send_seq=3608 receive_seq=3608 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76659 bytes_read=1465255 bytes_retransmit=0 bytes_invalid=0 send_seq=8167 receive_seq=8167 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998639 coil_temp=17.7 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=43.7 th1: temp=44.5 th2: temp=48.0 th3: temp=46.2 sysload=0.13 cputime=264.462 memavail=7397692 print_time=3498.785 buffer_time=2.215 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 78 Hz
Stats 3475.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20181515 bytes_read=2673655 bytes_retransmit=9 bytes_invalid=0 send_seq=357650 receive_seq=357650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=0 freq=400015555 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21820 bytes_read=69209 bytes_retransmit=0 bytes_invalid=0 send_seq=3608 receive_seq=3608 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997260 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122376 bytes_read=3607500 bytes_retransmit=9 bytes_invalid=0 send_seq=16388 receive_seq=16388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997670 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69448 bytes_read=1361245 bytes_retransmit=9 bytes_invalid=0 send_seq=8913 receive_seq=8913 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997587 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22087 bytes_read=884703 bytes_retransmit=9 bytes_invalid=0 send_seq=3622 receive_seq=3622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22573 bytes_read=67874 bytes_retransmit=9 bytes_invalid=0 send_seq=3609 receive_seq=3609 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999454 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76665 bytes_read=1465611 bytes_retransmit=0 bytes_invalid=0 send_seq=8168 receive_seq=8168 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998661 coil_temp=17.7 refs=0 mcu_temp=20.82 supply_voltage=3.012 th0: temp=43.6 th1: temp=44.6 th2: temp=47.9 th3: temp=46.2 sysload=0.13 cputime=264.552 memavail=7397716 print_time=3499.716 buffer_time=2.147 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 79 Hz
Stats 3476.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20184485 bytes_read=2674314 bytes_retransmit=9 bytes_invalid=0 send_seq=357714 receive_seq=357714 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=0 freq=400015548 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=21826 bytes_read=69238 bytes_retransmit=0 bytes_invalid=0 send_seq=3609 receive_seq=3609 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997268 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122382 bytes_read=3607628 bytes_retransmit=9 bytes_invalid=0 send_seq=16389 receive_seq=16389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997694 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69524 bytes_read=1364347 bytes_retransmit=9 bytes_invalid=0 send_seq=8924 receive_seq=8924 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997580 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22093 bytes_read=884997 bytes_retransmit=9 bytes_invalid=0 send_seq=3623 receive_seq=3623 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999518 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22579 bytes_read=67890 bytes_retransmit=9 bytes_invalid=0 send_seq=3610 receive_seq=3610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999456 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76671 bytes_read=1465967 bytes_retransmit=0 bytes_invalid=0 send_seq=8169 receive_seq=8169 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998662 coil_temp=17.7 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.7 th1: temp=44.7 th2: temp=47.9 th3: temp=46.1 sysload=0.13 cputime=264.642 memavail=7397720 print_time=3500.586 buffer_time=2.016 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 80 Hz
Stats 3477.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20188564 bytes_read=2675039 bytes_retransmit=9 bytes_invalid=0 send_seq=357797 receive_seq=357797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=15 upcoming_bytes=0 freq=400015673 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=21832 bytes_read=69254 bytes_retransmit=0 bytes_invalid=0 send_seq=3610 receive_seq=3610 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997266 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122388 bytes_read=3607728 bytes_retransmit=9 bytes_invalid=0 send_seq=16390 receive_seq=16390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997855 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69600 bytes_read=1367403 bytes_retransmit=9 bytes_invalid=0 send_seq=8935 receive_seq=8935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997579 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22099 bytes_read=885246 bytes_retransmit=9 bytes_invalid=0 send_seq=3624 receive_seq=3624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999519 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22585 bytes_read=67917 bytes_retransmit=9 bytes_invalid=0 send_seq=3611 receive_seq=3611 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999457 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76677 bytes_read=1466323 bytes_retransmit=0 bytes_invalid=0 send_seq=8170 receive_seq=8170 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998670 coil_temp=17.7 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.4 th1: temp=44.5 th2: temp=48.1 th3: temp=45.9 sysload=0.13 cputime=264.749 memavail=7393440 print_time=3501.790 buffer_time=2.219 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 81 Hz
Stats 3478.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20191813 bytes_read=2675685 bytes_retransmit=9 bytes_invalid=0 send_seq=357865 receive_seq=357865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=0 freq=400015699 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=21838 bytes_read=69270 bytes_retransmit=0 bytes_invalid=0 send_seq=3611 receive_seq=3611 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997082 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122394 bytes_read=3607828 bytes_retransmit=9 bytes_invalid=0 send_seq=16391 receive_seq=16391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997556 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69676 bytes_read=1370461 bytes_retransmit=9 bytes_invalid=0 send_seq=8946 receive_seq=8946 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997324 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22105 bytes_read=885480 bytes_retransmit=9 bytes_invalid=0 send_seq=3625 receive_seq=3625 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997493 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22591 bytes_read=67933 bytes_retransmit=9 bytes_invalid=0 send_seq=3612 receive_seq=3612 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999410 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76683 bytes_read=1466679 bytes_retransmit=0 bytes_invalid=0 send_seq=8171 receive_seq=8171 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998556 coil_temp=17.7 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.2 th1: temp=44.8 th2: temp=48.2 th3: temp=45.5 sysload=0.12 cputime=264.840 memavail=7399580 print_time=3502.727 buffer_time=2.156 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 82 Hz
Stats 3479.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20194812 bytes_read=2676353 bytes_retransmit=9 bytes_invalid=0 send_seq=357931 receive_seq=357931 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015694 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=21844 bytes_read=69286 bytes_retransmit=0 bytes_invalid=0 send_seq=3612 receive_seq=3612 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997071 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122400 bytes_read=3607956 bytes_retransmit=9 bytes_invalid=0 send_seq=16392 receive_seq=16392 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997508 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69752 bytes_read=1373547 bytes_retransmit=9 bytes_invalid=0 send_seq=8957 receive_seq=8957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997300 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22111 bytes_read=885774 bytes_retransmit=9 bytes_invalid=0 send_seq=3626 receive_seq=3626 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997501 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22597 bytes_read=67949 bytes_retransmit=9 bytes_invalid=0 send_seq=3613 receive_seq=3613 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999407 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76689 bytes_read=1467035 bytes_retransmit=0 bytes_invalid=0 send_seq=8172 receive_seq=8172 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998539 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.8 th1: temp=44.4 th2: temp=48.0 th3: temp=46.0 sysload=0.12 cputime=264.931 memavail=7399580 print_time=3503.598 buffer_time=2.028 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 83 Hz
Stats 3480.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20198899 bytes_read=2677099 bytes_retransmit=9 bytes_invalid=0 send_seq=358015 receive_seq=358015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=0 freq=400015676 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=21850 bytes_read=69302 bytes_retransmit=0 bytes_invalid=0 send_seq=3613 receive_seq=3613 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997104 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122406 bytes_read=3608070 bytes_retransmit=9 bytes_invalid=0 send_seq=16393 receive_seq=16393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997526 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69828 bytes_read=1376662 bytes_retransmit=9 bytes_invalid=0 send_seq=8968 receive_seq=8968 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997323 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22117 bytes_read=886008 bytes_retransmit=9 bytes_invalid=0 send_seq=3627 receive_seq=3627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997527 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22603 bytes_read=67965 bytes_retransmit=9 bytes_invalid=0 send_seq=3614 receive_seq=3614 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999424 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76695 bytes_read=1467391 bytes_retransmit=0 bytes_invalid=0 send_seq=8173 receive_seq=8173 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998569 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.8 th1: temp=44.5 th2: temp=48.2 th3: temp=46.3 sysload=0.12 cputime=265.032 memavail=7399580 print_time=3504.800 buffer_time=2.228 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 84 Hz
Stats 3481.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20202265 bytes_read=2677749 bytes_retransmit=9 bytes_invalid=0 send_seq=358083 receive_seq=358083 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=0 freq=400015668 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21856 bytes_read=69331 bytes_retransmit=0 bytes_invalid=0 send_seq=3614 receive_seq=3614 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997173 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122412 bytes_read=3608170 bytes_retransmit=9 bytes_invalid=0 send_seq=16394 receive_seq=16394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997605 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69904 bytes_read=1379737 bytes_retransmit=9 bytes_invalid=0 send_seq=8979 receive_seq=8979 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997409 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22123 bytes_read=886242 bytes_retransmit=9 bytes_invalid=0 send_seq=3628 receive_seq=3628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997584 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22609 bytes_read=67981 bytes_retransmit=9 bytes_invalid=0 send_seq=3615 receive_seq=3615 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76701 bytes_read=1467747 bytes_retransmit=0 bytes_invalid=0 send_seq=8174 receive_seq=8174 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998618 coil_temp=17.7 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.7 th1: temp=44.7 th2: temp=48.5 th3: temp=46.2 sysload=0.12 cputime=265.124 memavail=7399580 print_time=3505.734 buffer_time=2.161 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 85 Hz
Stats 3482.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20205334 bytes_read=2678423 bytes_retransmit=9 bytes_invalid=0 send_seq=358150 receive_seq=358150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015665 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21862 bytes_read=69347 bytes_retransmit=0 bytes_invalid=0 send_seq=3615 receive_seq=3615 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997189 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122418 bytes_read=3608298 bytes_retransmit=9 bytes_invalid=0 send_seq=16395 receive_seq=16395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997622 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=69980 bytes_read=1382822 bytes_retransmit=9 bytes_invalid=0 send_seq=8990 receive_seq=8990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997435 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22129 bytes_read=886551 bytes_retransmit=9 bytes_invalid=0 send_seq=3629 receive_seq=3629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997603 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22615 bytes_read=68008 bytes_retransmit=9 bytes_invalid=0 send_seq=3616 receive_seq=3616 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=31.1 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76707 bytes_read=1468103 bytes_retransmit=0 bytes_invalid=0 send_seq=8175 receive_seq=8175 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998630 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.2 th1: temp=44.7 th2: temp=48.2 th3: temp=46.2 sysload=0.12 cputime=265.215 memavail=7401224 print_time=3506.607 buffer_time=2.034 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 86 Hz
Stats 3483.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20209529 bytes_read=2679153 bytes_retransmit=9 bytes_invalid=0 send_seq=358234 receive_seq=358234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=0 freq=400015845 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21868 bytes_read=69363 bytes_retransmit=0 bytes_invalid=0 send_seq=3616 receive_seq=3616 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997190 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122424 bytes_read=3608398 bytes_retransmit=9 bytes_invalid=0 send_seq=16396 receive_seq=16396 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997617 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70056 bytes_read=1385880 bytes_retransmit=9 bytes_invalid=0 send_seq=9001 receive_seq=9001 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997469 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22135 bytes_read=886785 bytes_retransmit=9 bytes_invalid=0 send_seq=3630 receive_seq=3630 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997608 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22621 bytes_read=68024 bytes_retransmit=9 bytes_invalid=0 send_seq=3617 receive_seq=3617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76713 bytes_read=1468459 bytes_retransmit=0 bytes_invalid=0 send_seq=8176 receive_seq=8176 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998628 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=43.7 th1: temp=45.0 th2: temp=48.2 th3: temp=46.2 sysload=0.11 cputime=265.315 memavail=7401224 print_time=3507.816 buffer_time=2.243 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 87 Hz
Stats 3484.0: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20213003 bytes_read=2679829 bytes_retransmit=9 bytes_invalid=0 send_seq=358305 receive_seq=358305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015957 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21880 bytes_read=69395 bytes_retransmit=0 bytes_invalid=0 send_seq=3618 receive_seq=3618 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49996946 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122436 bytes_read=3608514 bytes_retransmit=9 bytes_invalid=0 send_seq=16398 receive_seq=16398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997292 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70138 bytes_read=1388956 bytes_retransmit=9 bytes_invalid=0 send_seq=9013 receive_seq=9013 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997131 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22147 bytes_read=887035 bytes_retransmit=9 bytes_invalid=0 send_seq=3632 receive_seq=3632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997362 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22633 bytes_read=68056 bytes_retransmit=9 bytes_invalid=0 send_seq=3619 receive_seq=3619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999376 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76725 bytes_read=1468831 bytes_retransmit=0 bytes_invalid=0 send_seq=8178 receive_seq=8178 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998466 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.1 th1: temp=44.6 th2: temp=48.3 th3: temp=46.1 sysload=0.11 cputime=265.410 memavail=7401224 print_time=3508.743 buffer_time=2.169 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 88 Hz
Stats 3485.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20216002 bytes_read=2680514 bytes_retransmit=9 bytes_invalid=0 send_seq=358371 receive_seq=358371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015936 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21886 bytes_read=69411 bytes_retransmit=0 bytes_invalid=0 send_seq=3619 receive_seq=3619 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49996824 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122442 bytes_read=3608656 bytes_retransmit=9 bytes_invalid=0 send_seq=16399 receive_seq=16399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997105 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70214 bytes_read=1392041 bytes_retransmit=9 bytes_invalid=0 send_seq=9024 receive_seq=9024 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63996939 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22153 bytes_read=887329 bytes_retransmit=9 bytes_invalid=0 send_seq=3633 receive_seq=3633 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997231 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22639 bytes_read=68072 bytes_retransmit=9 bytes_invalid=0 send_seq=3620 receive_seq=3620 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999341 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76731 bytes_read=1469187 bytes_retransmit=0 bytes_invalid=0 send_seq=8179 receive_seq=8179 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998375 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.0 th1: temp=44.8 th2: temp=48.7 th3: temp=46.3 sysload=0.11 cputime=265.500 memavail=7401224 print_time=3509.612 buffer_time=2.038 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 89 Hz
Stats 3486.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20220224 bytes_read=2681254 bytes_retransmit=9 bytes_invalid=0 send_seq=358457 receive_seq=358457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=15 upcoming_bytes=0 freq=400015894 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21892 bytes_read=69440 bytes_retransmit=0 bytes_invalid=0 send_seq=3620 receive_seq=3620 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49996905 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122448 bytes_read=3608756 bytes_retransmit=9 bytes_invalid=0 send_seq=16400 receive_seq=16400 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997219 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70283 bytes_read=1395091 bytes_retransmit=9 bytes_invalid=0 send_seq=9034 receive_seq=9034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997028 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22159 bytes_read=887563 bytes_retransmit=9 bytes_invalid=0 send_seq=3634 receive_seq=3634 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999521 adj=47997303 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22645 bytes_read=68088 bytes_retransmit=9 bytes_invalid=0 send_seq=3621 receive_seq=3621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999357 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76737 bytes_read=1469543 bytes_retransmit=0 bytes_invalid=0 send_seq=8180 receive_seq=8180 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998421 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.7 th1: temp=44.8 th2: temp=48.4 th3: temp=46.3 sysload=0.11 cputime=265.602 memavail=7401036 print_time=3510.814 buffer_time=2.239 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 90 Hz
Stats 3487.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20223775 bytes_read=2681939 bytes_retransmit=9 bytes_invalid=0 send_seq=358532 receive_seq=358532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015866 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21898 bytes_read=69456 bytes_retransmit=0 bytes_invalid=0 send_seq=3621 receive_seq=3621 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997053 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122454 bytes_read=3608856 bytes_retransmit=9 bytes_invalid=0 send_seq=16401 receive_seq=16401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997412 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70359 bytes_read=1398207 bytes_retransmit=9 bytes_invalid=0 send_seq=9045 receive_seq=9045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997236 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22165 bytes_read=887812 bytes_retransmit=9 bytes_invalid=0 send_seq=3635 receive_seq=3635 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999523 adj=47997454 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22651 bytes_read=68115 bytes_retransmit=9 bytes_invalid=0 send_seq=3622 receive_seq=3622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999395 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76743 bytes_read=1469899 bytes_retransmit=0 bytes_invalid=0 send_seq=8181 receive_seq=8181 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998521 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.6 th1: temp=44.6 th2: temp=48.4 th3: temp=46.2 sysload=0.11 cputime=265.696 memavail=7401036 print_time=3511.751 buffer_time=2.176 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 91 Hz
Stats 3488.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20226806 bytes_read=2682608 bytes_retransmit=9 bytes_invalid=0 send_seq=358598 receive_seq=358598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015850 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21904 bytes_read=69472 bytes_retransmit=0 bytes_invalid=0 send_seq=3622 receive_seq=3622 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997113 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122460 bytes_read=3608984 bytes_retransmit=9 bytes_invalid=0 send_seq=16402 receive_seq=16402 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997484 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70435 bytes_read=1401292 bytes_retransmit=9 bytes_invalid=0 send_seq=9056 receive_seq=9056 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997316 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22171 bytes_read=888106 bytes_retransmit=9 bytes_invalid=0 send_seq=3636 receive_seq=3636 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999523 adj=47997544 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22657 bytes_read=68131 bytes_retransmit=9 bytes_invalid=0 send_seq=3623 receive_seq=3623 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999410 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76749 bytes_read=1470255 bytes_retransmit=0 bytes_invalid=0 send_seq=8182 receive_seq=8182 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998564 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.0 th1: temp=44.8 th2: temp=48.4 th3: temp=46.2 sysload=0.10 cputime=265.788 memavail=7401036 print_time=3512.627 buffer_time=2.052 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 92 Hz
Stats 3489.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20231144 bytes_read=2683353 bytes_retransmit=9 bytes_invalid=0 send_seq=358686 receive_seq=358686 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=15 upcoming_bytes=0 freq=400015814 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21910 bytes_read=69488 bytes_retransmit=0 bytes_invalid=0 send_seq=3623 receive_seq=3623 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997146 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122466 bytes_read=3609084 bytes_retransmit=9 bytes_invalid=0 send_seq=16403 receive_seq=16403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997518 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70511 bytes_read=1404349 bytes_retransmit=9 bytes_invalid=0 send_seq=9067 receive_seq=9067 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997359 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22177 bytes_read=888340 bytes_retransmit=9 bytes_invalid=0 send_seq=3637 receive_seq=3637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997577 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22663 bytes_read=68147 bytes_retransmit=9 bytes_invalid=0 send_seq=3624 receive_seq=3624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999418 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76755 bytes_read=1470611 bytes_retransmit=0 bytes_invalid=0 send_seq=8183 receive_seq=8183 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999913 adj=31998584 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=43.7 th1: temp=44.9 th2: temp=48.4 th3: temp=46.4 sysload=0.10 cputime=265.893 memavail=7401036 print_time=3513.834 buffer_time=2.257 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 93 Hz
Stats 3490.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20234810 bytes_read=2684059 bytes_retransmit=9 bytes_invalid=0 send_seq=358762 receive_seq=358762 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015804 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21916 bytes_read=69504 bytes_retransmit=0 bytes_invalid=0 send_seq=3624 receive_seq=3624 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997227 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122472 bytes_read=3609198 bytes_retransmit=9 bytes_invalid=0 send_seq=16404 receive_seq=16404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997614 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70587 bytes_read=1407406 bytes_retransmit=9 bytes_invalid=0 send_seq=9078 receive_seq=9078 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997475 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22183 bytes_read=888574 bytes_retransmit=9 bytes_invalid=0 send_seq=3638 receive_seq=3638 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22669 bytes_read=68163 bytes_retransmit=9 bytes_invalid=0 send_seq=3625 receive_seq=3625 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999436 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76761 bytes_read=1470967 bytes_retransmit=0 bytes_invalid=0 send_seq=8184 receive_seq=8184 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998635 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.0 th1: temp=44.9 th2: temp=48.4 th3: temp=46.4 sysload=0.10 cputime=265.988 memavail=7401036 print_time=3514.759 buffer_time=2.183 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 94 Hz
Stats 3491.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20237840 bytes_read=2684733 bytes_retransmit=9 bytes_invalid=0 send_seq=358829 receive_seq=358829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015775 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21922 bytes_read=69520 bytes_retransmit=0 bytes_invalid=0 send_seq=3625 receive_seq=3625 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997242 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122478 bytes_read=3609326 bytes_retransmit=9 bytes_invalid=0 send_seq=16405 receive_seq=16405 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997642 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70663 bytes_read=1410508 bytes_retransmit=9 bytes_invalid=0 send_seq=9089 receive_seq=9089 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997486 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22189 bytes_read=888868 bytes_retransmit=9 bytes_invalid=0 send_seq=3639 receive_seq=3639 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22675 bytes_read=68179 bytes_retransmit=9 bytes_invalid=0 send_seq=3626 receive_seq=3626 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76767 bytes_read=1471323 bytes_retransmit=0 bytes_invalid=0 send_seq=8185 receive_seq=8185 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998641 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.2 th1: temp=44.8 th2: temp=48.5 th3: temp=46.5 sysload=0.10 cputime=266.082 memavail=7401036 print_time=3515.631 buffer_time=2.054 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 95 Hz
Stats 3492.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20242166 bytes_read=2685428 bytes_retransmit=9 bytes_invalid=0 send_seq=358916 receive_seq=358906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=29 upcoming_bytes=0 freq=400015771 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21928 bytes_read=69549 bytes_retransmit=0 bytes_invalid=0 send_seq=3626 receive_seq=3626 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997289 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122484 bytes_read=3609426 bytes_retransmit=9 bytes_invalid=0 send_seq=16406 receive_seq=16406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997756 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70739 bytes_read=1413564 bytes_retransmit=9 bytes_invalid=0 send_seq=9100 receive_seq=9100 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22195 bytes_read=889117 bytes_retransmit=9 bytes_invalid=0 send_seq=3640 receive_seq=3640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997709 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22681 bytes_read=68206 bytes_retransmit=9 bytes_invalid=0 send_seq=3627 receive_seq=3627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999453 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76773 bytes_read=1471679 bytes_retransmit=0 bytes_invalid=0 send_seq=8186 receive_seq=8186 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998671 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.3 th1: temp=45.0 th2: temp=48.4 th3: temp=46.5 sysload=0.10 cputime=266.187 memavail=7401056 print_time=3516.826 buffer_time=2.248 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 96 Hz
Stats 3493.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20245884 bytes_read=2686168 bytes_retransmit=9 bytes_invalid=0 send_seq=358992 receive_seq=358992 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=0 freq=400015742 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21934 bytes_read=69565 bytes_retransmit=0 bytes_invalid=0 send_seq=3627 receive_seq=3627 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997279 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122490 bytes_read=3609526 bytes_retransmit=9 bytes_invalid=0 send_seq=16407 receive_seq=16407 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997725 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70815 bytes_read=1416623 bytes_retransmit=9 bytes_invalid=0 send_seq=9111 receive_seq=9111 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997530 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22201 bytes_read=889351 bytes_retransmit=9 bytes_invalid=0 send_seq=3641 receive_seq=3641 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22687 bytes_read=68222 bytes_retransmit=9 bytes_invalid=0 send_seq=3628 receive_seq=3628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76779 bytes_read=1472035 bytes_retransmit=0 bytes_invalid=0 send_seq=8187 receive_seq=8187 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998663 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=44.1 th1: temp=44.9 th2: temp=48.7 th3: temp=46.3 sysload=0.09 cputime=266.282 memavail=7401056 print_time=3517.772 buffer_time=2.193 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 97 Hz
Stats 3494.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20248945 bytes_read=2686842 bytes_retransmit=9 bytes_invalid=0 send_seq=359059 receive_seq=359059 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015725 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21940 bytes_read=69581 bytes_retransmit=0 bytes_invalid=0 send_seq=3628 receive_seq=3628 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997310 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122496 bytes_read=3609654 bytes_retransmit=9 bytes_invalid=0 send_seq=16408 receive_seq=16408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997760 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70891 bytes_read=1419769 bytes_retransmit=9 bytes_invalid=0 send_seq=9122 receive_seq=9122 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997577 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22207 bytes_read=889645 bytes_retransmit=9 bytes_invalid=0 send_seq=3642 receive_seq=3642 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997724 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22693 bytes_read=68238 bytes_retransmit=9 bytes_invalid=0 send_seq=3629 receive_seq=3629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999459 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76785 bytes_read=1472391 bytes_retransmit=0 bytes_invalid=0 send_seq=8188 receive_seq=8188 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998689 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.0 th1: temp=44.9 th2: temp=48.4 th3: temp=46.4 sysload=0.09 cputime=266.381 memavail=7394760 print_time=3518.640 buffer_time=2.061 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 98 Hz
Stats 3495.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20253393 bytes_read=2687543 bytes_retransmit=9 bytes_invalid=0 send_seq=359145 receive_seq=359134 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015700 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21946 bytes_read=69597 bytes_retransmit=0 bytes_invalid=0 send_seq=3629 receive_seq=3629 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997343 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122502 bytes_read=3609768 bytes_retransmit=9 bytes_invalid=0 send_seq=16409 receive_seq=16409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997775 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=70967 bytes_read=1422825 bytes_retransmit=9 bytes_invalid=0 send_seq=9133 receive_seq=9133 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997614 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22213 bytes_read=889879 bytes_retransmit=9 bytes_invalid=0 send_seq=3643 receive_seq=3643 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997741 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22699 bytes_read=68254 bytes_retransmit=9 bytes_invalid=0 send_seq=3630 receive_seq=3630 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999468 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76791 bytes_read=1472747 bytes_retransmit=0 bytes_invalid=0 send_seq=8189 receive_seq=8189 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998702 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=44.1 th1: temp=45.1 th2: temp=48.3 th3: temp=46.4 sysload=0.09 cputime=266.489 memavail=7400644 print_time=3519.841 buffer_time=2.260 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 99 Hz
Stats 3496.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20257172 bytes_read=2688303 bytes_retransmit=9 bytes_invalid=0 send_seq=359224 receive_seq=359224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=0 freq=400015674 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21952 bytes_read=69613 bytes_retransmit=0 bytes_invalid=0 send_seq=3630 receive_seq=3630 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997389 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122508 bytes_read=3609868 bytes_retransmit=9 bytes_invalid=0 send_seq=16410 receive_seq=16410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997786 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71043 bytes_read=1425899 bytes_retransmit=9 bytes_invalid=0 send_seq=9144 receive_seq=9144 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997628 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22219 bytes_read=890113 bytes_retransmit=9 bytes_invalid=0 send_seq=3644 receive_seq=3644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997751 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22705 bytes_read=68270 bytes_retransmit=9 bytes_invalid=0 send_seq=3631 receive_seq=3631 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999473 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76797 bytes_read=1473103 bytes_retransmit=0 bytes_invalid=0 send_seq=8190 receive_seq=8190 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999912 adj=31998708 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.0 th1: temp=44.9 th2: temp=48.6 th3: temp=46.5 sysload=0.09 cputime=266.587 memavail=7399940 print_time=3520.772 buffer_time=2.190 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 100 Hz
Stats 3497.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20260299 bytes_read=2688982 bytes_retransmit=9 bytes_invalid=0 send_seq=359292 receive_seq=359292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015653 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21958 bytes_read=69642 bytes_retransmit=0 bytes_invalid=0 send_seq=3631 receive_seq=3631 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999215 adj=49997409 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122514 bytes_read=3609996 bytes_retransmit=9 bytes_invalid=0 send_seq=16411 receive_seq=16411 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997815 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71119 bytes_read=1428985 bytes_retransmit=9 bytes_invalid=0 send_seq=9155 receive_seq=9155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997657 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22225 bytes_read=890422 bytes_retransmit=9 bytes_invalid=0 send_seq=3645 receive_seq=3645 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999524 adj=47997768 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22711 bytes_read=68297 bytes_retransmit=9 bytes_invalid=0 send_seq=3632 receive_seq=3632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999477 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=31.1 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76803 bytes_read=1473459 bytes_retransmit=0 bytes_invalid=0 send_seq=8191 receive_seq=8191 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998727 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.3 th1: temp=44.9 th2: temp=48.6 th3: temp=46.6 sysload=0.09 cputime=266.683 memavail=7399948 print_time=3521.641 buffer_time=2.059 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 101 Hz
Stats 3498.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20264813 bytes_read=2689727 bytes_retransmit=9 bytes_invalid=0 send_seq=359383 receive_seq=359379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=15 upcoming_bytes=0 freq=400015631 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21964 bytes_read=69658 bytes_retransmit=0 bytes_invalid=0 send_seq=3632 receive_seq=3632 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999215 adj=49997446 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122520 bytes_read=3610096 bytes_retransmit=9 bytes_invalid=0 send_seq=16412 receive_seq=16412 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997833 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71195 bytes_read=1432041 bytes_retransmit=9 bytes_invalid=0 send_seq=9166 receive_seq=9166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000034 adj=63997682 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22231 bytes_read=890656 bytes_retransmit=9 bytes_invalid=0 send_seq=3646 receive_seq=3646 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997788 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22717 bytes_read=68313 bytes_retransmit=9 bytes_invalid=0 send_seq=3633 receive_seq=3633 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999482 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76809 bytes_read=1473815 bytes_retransmit=0 bytes_invalid=0 send_seq=8192 receive_seq=8192 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998738 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.2 th1: temp=44.7 th2: temp=48.4 th3: temp=46.6 sysload=0.08 cputime=266.790 memavail=7399948 print_time=3522.846 buffer_time=2.256 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 102 Hz
Stats 3499.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20268705 bytes_read=2690462 bytes_retransmit=9 bytes_invalid=0 send_seq=359464 receive_seq=359464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015605 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21970 bytes_read=69674 bytes_retransmit=0 bytes_invalid=0 send_seq=3633 receive_seq=3633 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999219 adj=49997420 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122526 bytes_read=3610210 bytes_retransmit=9 bytes_invalid=0 send_seq=16413 receive_seq=16413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997821 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71271 bytes_read=1435155 bytes_retransmit=9 bytes_invalid=0 send_seq=9177 receive_seq=9177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997677 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22237 bytes_read=890890 bytes_retransmit=9 bytes_invalid=0 send_seq=3647 receive_seq=3647 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997781 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22723 bytes_read=68329 bytes_retransmit=9 bytes_invalid=0 send_seq=3634 receive_seq=3634 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999480 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76815 bytes_read=1474171 bytes_retransmit=0 bytes_invalid=0 send_seq=8193 receive_seq=8193 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999911 adj=31998736 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.1 th1: temp=45.2 th2: temp=48.6 th3: temp=46.6 sysload=0.08 cputime=266.889 memavail=7399960 print_time=3523.781 buffer_time=2.190 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 103 Hz
Stats 3500.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20271829 bytes_read=2691152 bytes_retransmit=9 bytes_invalid=0 send_seq=359532 receive_seq=359532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015587 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21976 bytes_read=69690 bytes_retransmit=0 bytes_invalid=0 send_seq=3634 receive_seq=3634 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999219 adj=49997490 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122532 bytes_read=3610338 bytes_retransmit=9 bytes_invalid=0 send_seq=16414 receive_seq=16414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997848 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71340 bytes_read=1438217 bytes_retransmit=9 bytes_invalid=0 send_seq=9187 receive_seq=9187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997718 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22243 bytes_read=891184 bytes_retransmit=9 bytes_invalid=0 send_seq=3648 receive_seq=3648 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997803 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22729 bytes_read=68345 bytes_retransmit=9 bytes_invalid=0 send_seq=3635 receive_seq=3635 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999484 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76821 bytes_read=1474527 bytes_retransmit=0 bytes_invalid=0 send_seq=8194 receive_seq=8194 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998747 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=43.9 th1: temp=45.0 th2: temp=48.5 th3: temp=46.6 sysload=0.08 cputime=266.984 memavail=7399960 print_time=3524.651 buffer_time=2.060 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 104 Hz
Stats 3501.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20276477 bytes_read=2691887 bytes_retransmit=9 bytes_invalid=0 send_seq=359624 receive_seq=359617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015567 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=21982 bytes_read=69706 bytes_retransmit=0 bytes_invalid=0 send_seq=3635 receive_seq=3635 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999219 adj=49997497 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122538 bytes_read=3610438 bytes_retransmit=9 bytes_invalid=0 send_seq=16415 receive_seq=16415 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997857 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71416 bytes_read=1441294 bytes_retransmit=9 bytes_invalid=0 send_seq=9198 receive_seq=9198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997730 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22249 bytes_read=891418 bytes_retransmit=9 bytes_invalid=0 send_seq=3649 receive_seq=3649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997817 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22735 bytes_read=68361 bytes_retransmit=9 bytes_invalid=0 send_seq=3636 receive_seq=3636 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999486 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76827 bytes_read=1474883 bytes_retransmit=0 bytes_invalid=0 send_seq=8195 receive_seq=8195 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998822 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=44.7 th1: temp=45.2 th2: temp=48.6 th3: temp=46.4 sysload=0.08 cputime=267.094 memavail=7399708 print_time=3525.855 buffer_time=2.262 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 105 Hz
Stats 3502.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20280441 bytes_read=2692642 bytes_retransmit=9 bytes_invalid=0 send_seq=359706 receive_seq=359706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=0 freq=400015579 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21988 bytes_read=69735 bytes_retransmit=0 bytes_invalid=0 send_seq=3636 receive_seq=3636 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999218 adj=49997457 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122544 bytes_read=3610552 bytes_retransmit=9 bytes_invalid=0 send_seq=16416 receive_seq=16416 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997853 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71492 bytes_read=1444352 bytes_retransmit=9 bytes_invalid=0 send_seq=9209 receive_seq=9209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997712 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22255 bytes_read=891667 bytes_retransmit=9 bytes_invalid=0 send_seq=3650 receive_seq=3650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997795 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22741 bytes_read=68388 bytes_retransmit=9 bytes_invalid=0 send_seq=3637 receive_seq=3637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999483 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76833 bytes_read=1475239 bytes_retransmit=0 bytes_invalid=0 send_seq=8196 receive_seq=8196 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998858 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.3 th1: temp=45.1 th2: temp=48.6 th3: temp=46.5 sysload=0.08 cputime=267.197 memavail=7399716 print_time=3526.787 buffer_time=2.194 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 106 Hz
Stats 3503.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20283572 bytes_read=2693326 bytes_retransmit=9 bytes_invalid=0 send_seq=359775 receive_seq=359775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=22 upcoming_bytes=0 freq=400015584 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=21994 bytes_read=69751 bytes_retransmit=0 bytes_invalid=0 send_seq=3637 receive_seq=3637 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997400 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122550 bytes_read=3610666 bytes_retransmit=9 bytes_invalid=0 send_seq=16417 receive_seq=16417 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997804 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71568 bytes_read=1447438 bytes_retransmit=9 bytes_invalid=0 send_seq=9220 receive_seq=9220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997661 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22261 bytes_read=891961 bytes_retransmit=9 bytes_invalid=0 send_seq=3651 receive_seq=3651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997757 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22747 bytes_read=68404 bytes_retransmit=9 bytes_invalid=0 send_seq=3638 receive_seq=3638 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999472 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76839 bytes_read=1475595 bytes_retransmit=0 bytes_invalid=0 send_seq=8197 receive_seq=8197 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998822 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.4 th1: temp=45.2 th2: temp=48.7 th3: temp=46.4 sysload=0.08 cputime=267.295 memavail=7399720 print_time=3527.647 buffer_time=2.053 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 107 Hz
Stats 3504.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20288293 bytes_read=2694091 bytes_retransmit=9 bytes_invalid=0 send_seq=359869 receive_seq=359866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=0 freq=400015662 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22000 bytes_read=69767 bytes_retransmit=0 bytes_invalid=0 send_seq=3638 receive_seq=3638 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997366 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122556 bytes_read=3610766 bytes_retransmit=9 bytes_invalid=0 send_seq=16418 receive_seq=16418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997778 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71644 bytes_read=1450552 bytes_retransmit=9 bytes_invalid=0 send_seq=9231 receive_seq=9231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997637 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22267 bytes_read=892195 bytes_retransmit=9 bytes_invalid=0 send_seq=3652 receive_seq=3652 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997741 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22753 bytes_read=68420 bytes_retransmit=9 bytes_invalid=0 send_seq=3639 receive_seq=3639 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999469 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76845 bytes_read=1475951 bytes_retransmit=0 bytes_invalid=0 send_seq=8198 receive_seq=8198 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998791 coil_temp=17.6 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=44.5 th1: temp=45.1 th2: temp=48.6 th3: temp=46.6 sysload=0.08 cputime=267.409 memavail=7399724 print_time=3528.859 buffer_time=2.260 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 108 Hz
Stats 3505.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20292351 bytes_read=2694852 bytes_retransmit=9 bytes_invalid=0 send_seq=359953 receive_seq=359953 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015673 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22006 bytes_read=69783 bytes_retransmit=0 bytes_invalid=0 send_seq=3639 receive_seq=3639 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997214 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=122562 bytes_read=3610894 bytes_retransmit=9 bytes_invalid=0 send_seq=16419 receive_seq=16419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997603 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71720 bytes_read=1453623 bytes_retransmit=9 bytes_invalid=0 send_seq=9242 receive_seq=9242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997485 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22273 bytes_read=892429 bytes_retransmit=9 bytes_invalid=0 send_seq=3653 receive_seq=3653 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997603 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22759 bytes_read=68436 bytes_retransmit=9 bytes_invalid=0 send_seq=3640 receive_seq=3640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999444 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76851 bytes_read=1476307 bytes_retransmit=0 bytes_invalid=0 send_seq=8199 receive_seq=8199 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998679 coil_temp=17.6 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=44.3 th1: temp=45.0 th2: temp=48.4 th3: temp=46.6 sysload=0.08 cputime=267.512 memavail=7399728 print_time=3529.784 buffer_time=2.184 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 109 Hz
Stats 3506.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20295560 bytes_read=2695541 bytes_retransmit=9 bytes_invalid=0 send_seq=360023 receive_seq=360023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=0 freq=400015662 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22012 bytes_read=69812 bytes_retransmit=0 bytes_invalid=0 send_seq=3640 receive_seq=3640 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999215 adj=49997208 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=122568 bytes_read=3611008 bytes_retransmit=9 bytes_invalid=0 send_seq=16420 receive_seq=16420 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997585 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71796 bytes_read=1456712 bytes_retransmit=9 bytes_invalid=0 send_seq=9253 receive_seq=9253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997465 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22279 bytes_read=892723 bytes_retransmit=9 bytes_invalid=0 send_seq=3654 receive_seq=3654 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999525 adj=47997592 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22765 bytes_read=68452 bytes_retransmit=9 bytes_invalid=0 send_seq=3641 receive_seq=3641 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76857 bytes_read=1476663 bytes_retransmit=0 bytes_invalid=0 send_seq=8200 receive_seq=8200 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998659 coil_temp=17.6 refs=0 mcu_temp=20.76 supply_voltage=3.012 th0: temp=44.5 th1: temp=44.9 th2: temp=48.6 th3: temp=46.6 sysload=0.08 cputime=267.615 memavail=7398972 print_time=3530.664 buffer_time=2.063 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 110 Hz
Stats 3507.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20300351 bytes_read=2696261 bytes_retransmit=9 bytes_invalid=0 send_seq=360116 receive_seq=360105 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=0 freq=400015647 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22018 bytes_read=69828 bytes_retransmit=0 bytes_invalid=0 send_seq=3641 receive_seq=3641 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999214 adj=49997212 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=122574 bytes_read=3611108 bytes_retransmit=9 bytes_invalid=0 send_seq=16421 receive_seq=16421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997609 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71872 bytes_read=1459769 bytes_retransmit=9 bytes_invalid=0 send_seq=9264 receive_seq=9264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22285 bytes_read=892972 bytes_retransmit=9 bytes_invalid=0 send_seq=3655 receive_seq=3655 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999526 adj=47997612 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22771 bytes_read=68479 bytes_retransmit=9 bytes_invalid=0 send_seq=3642 receive_seq=3642 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76863 bytes_read=1477019 bytes_retransmit=0 bytes_invalid=0 send_seq=8201 receive_seq=8201 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998674 coil_temp=17.6 refs=0 mcu_temp=20.76 supply_voltage=3.012 th0: temp=44.5 th1: temp=45.3 th2: temp=48.6 th3: temp=46.5 sysload=0.08 cputime=267.721 memavail=7398980 print_time=3531.865 buffer_time=2.263 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 111 Hz
Stats 3508.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20304427 bytes_read=2697041 bytes_retransmit=9 bytes_invalid=0 send_seq=360199 receive_seq=360199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=400015631 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22024 bytes_read=69844 bytes_retransmit=0 bytes_invalid=0 send_seq=3642 receive_seq=3642 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999214 adj=49997232 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=122580 bytes_read=3611222 bytes_retransmit=9 bytes_invalid=0 send_seq=16422 receive_seq=16422 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997660 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=71948 bytes_read=1462840 bytes_retransmit=9 bytes_invalid=0 send_seq=9275 receive_seq=9275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997534 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22291 bytes_read=893206 bytes_retransmit=9 bytes_invalid=0 send_seq=3656 receive_seq=3656 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22777 bytes_read=68495 bytes_retransmit=9 bytes_invalid=0 send_seq=3643 receive_seq=3643 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76869 bytes_read=1477375 bytes_retransmit=0 bytes_invalid=0 send_seq=8202 receive_seq=8202 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998682 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.5 th1: temp=45.2 th2: temp=48.7 th3: temp=46.5 sysload=0.07 cputime=267.821 memavail=7398980 print_time=3532.790 buffer_time=2.187 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 112 Hz
Stats 3509.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20307591 bytes_read=2697725 bytes_retransmit=9 bytes_invalid=0 send_seq=360268 receive_seq=360268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=0 freq=400015625 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22030 bytes_read=69860 bytes_retransmit=0 bytes_invalid=0 send_seq=3643 receive_seq=3643 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999214 adj=49997258 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=122586 bytes_read=3611336 bytes_retransmit=9 bytes_invalid=0 send_seq=16423 receive_seq=16423 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997776 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=72024 bytes_read=1465914 bytes_retransmit=9 bytes_invalid=0 send_seq=9286 receive_seq=9286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997562 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22297 bytes_read=893500 bytes_retransmit=9 bytes_invalid=0 send_seq=3657 receive_seq=3657 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997697 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22783 bytes_read=68511 bytes_retransmit=9 bytes_invalid=0 send_seq=3644 receive_seq=3644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999469 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76875 bytes_read=1477731 bytes_retransmit=0 bytes_invalid=0 send_seq=8203 receive_seq=8203 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998694 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.3 th1: temp=45.2 th2: temp=48.7 th3: temp=46.7 sysload=0.07 cputime=267.919 memavail=7398984 print_time=3533.662 buffer_time=2.059 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 113 Hz
Stats 3510.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20312405 bytes_read=2698518 bytes_retransmit=9 bytes_invalid=0 send_seq=360364 receive_seq=360362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=47 upcoming_bytes=0 freq=400015621 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22036 bytes_read=69876 bytes_retransmit=0 bytes_invalid=0 send_seq=3644 receive_seq=3644 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999215 adj=49997268 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=122592 bytes_read=3611436 bytes_retransmit=9 bytes_invalid=0 send_seq=16424 receive_seq=16424 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997768 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=72100 bytes_read=1469030 bytes_retransmit=9 bytes_invalid=0 send_seq=9297 receive_seq=9297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997567 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22303 bytes_read=893734 bytes_retransmit=9 bytes_invalid=0 send_seq=3658 receive_seq=3658 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22789 bytes_read=68527 bytes_retransmit=9 bytes_invalid=0 send_seq=3645 receive_seq=3645 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999467 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=31.1 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76881 bytes_read=1478087 bytes_retransmit=0 bytes_invalid=0 send_seq=8204 receive_seq=8204 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998687 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=45.1 th1: temp=45.2 th2: temp=48.6 th3: temp=46.7 sysload=0.07 cputime=268.031 memavail=7398984 print_time=3534.869 buffer_time=2.258 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 114 Hz
Stats 3511.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20316597 bytes_read=2699266 bytes_retransmit=9 bytes_invalid=0 send_seq=360450 receive_seq=360450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015606 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22042 bytes_read=69905 bytes_retransmit=0 bytes_invalid=0 send_seq=3645 receive_seq=3645 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997287 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122598 bytes_read=3611578 bytes_retransmit=9 bytes_invalid=0 send_seq=16425 receive_seq=16425 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997744 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=72176 bytes_read=1472117 bytes_retransmit=9 bytes_invalid=0 send_seq=9308 receive_seq=9308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22309 bytes_read=893983 bytes_retransmit=9 bytes_invalid=0 send_seq=3659 receive_seq=3659 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997702 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22795 bytes_read=68543 bytes_retransmit=9 bytes_invalid=0 send_seq=3646 receive_seq=3646 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999461 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76887 bytes_read=1478443 bytes_retransmit=0 bytes_invalid=0 send_seq=8205 receive_seq=8205 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998695 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.6 th1: temp=45.5 th2: temp=48.3 th3: temp=46.7 sysload=0.07 cputime=268.135 memavail=7398732 print_time=3535.797 buffer_time=2.185 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 115 Hz
Stats 3512.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20319849 bytes_read=2699960 bytes_retransmit=9 bytes_invalid=0 send_seq=360521 receive_seq=360521 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=0 freq=400015598 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22048 bytes_read=69921 bytes_retransmit=0 bytes_invalid=0 send_seq=3646 receive_seq=3646 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997316 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122604 bytes_read=3611678 bytes_retransmit=9 bytes_invalid=0 send_seq=16426 receive_seq=16426 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997754 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=72252 bytes_read=1475187 bytes_retransmit=9 bytes_invalid=0 send_seq=9319 receive_seq=9319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997676 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22315 bytes_read=894277 bytes_retransmit=9 bytes_invalid=0 send_seq=3660 receive_seq=3660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997713 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22801 bytes_read=68570 bytes_retransmit=9 bytes_invalid=0 send_seq=3647 receive_seq=3647 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999464 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76893 bytes_read=1478799 bytes_retransmit=0 bytes_invalid=0 send_seq=8206 receive_seq=8206 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998711 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.2 th1: temp=45.2 th2: temp=48.8 th3: temp=46.7 sysload=0.07 cputime=268.242 memavail=7399604 print_time=3536.668 buffer_time=2.055 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 116 Hz
Stats 3513.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20324757 bytes_read=2700715 bytes_retransmit=9 bytes_invalid=0 send_seq=360619 receive_seq=360610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=0 freq=400015588 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22054 bytes_read=69937 bytes_retransmit=0 bytes_invalid=0 send_seq=3647 receive_seq=3647 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997339 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122610 bytes_read=3611778 bytes_retransmit=9 bytes_invalid=0 send_seq=16427 receive_seq=16427 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997756 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=72328 bytes_read=1478246 bytes_retransmit=9 bytes_invalid=0 send_seq=9330 receive_seq=9330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997676 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22321 bytes_read=894511 bytes_retransmit=9 bytes_invalid=0 send_seq=3661 receive_seq=3661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997714 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22807 bytes_read=68586 bytes_retransmit=9 bytes_invalid=0 send_seq=3648 receive_seq=3648 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999473 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76899 bytes_read=1479155 bytes_retransmit=0 bytes_invalid=0 send_seq=8207 receive_seq=8207 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998730 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.3 th1: temp=45.3 th2: temp=48.7 th3: temp=46.8 sysload=0.06 cputime=268.354 memavail=7399604 print_time=3537.879 buffer_time=2.264 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 117 Hz
Stats 3514.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20328956 bytes_read=2701500 bytes_retransmit=9 bytes_invalid=0 send_seq=360705 receive_seq=360705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015576 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22060 bytes_read=69953 bytes_retransmit=0 bytes_invalid=0 send_seq=3648 receive_seq=3648 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997323 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122616 bytes_read=3611906 bytes_retransmit=9 bytes_invalid=0 send_seq=16428 receive_seq=16428 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997751 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=72404 bytes_read=1481317 bytes_retransmit=9 bytes_invalid=0 send_seq=9341 receive_seq=9341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997647 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22327 bytes_read=894760 bytes_retransmit=9 bytes_invalid=0 send_seq=3662 receive_seq=3662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997713 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22813 bytes_read=68602 bytes_retransmit=9 bytes_invalid=0 send_seq=3649 receive_seq=3649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999467 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76905 bytes_read=1479511 bytes_retransmit=0 bytes_invalid=0 send_seq=8208 receive_seq=8208 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998721 coil_temp=17.6 refs=0 mcu_temp=20.81 supply_voltage=3.012 th0: temp=44.7 th1: temp=45.0 th2: temp=48.7 th3: temp=46.8 sysload=0.06 cputime=268.455 memavail=7399604 print_time=3538.803 buffer_time=2.187 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 118 Hz
Stats 3515.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20332251 bytes_read=2702210 bytes_retransmit=9 bytes_invalid=0 send_seq=360776 receive_seq=360776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=0 freq=400015782 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22066 bytes_read=69969 bytes_retransmit=0 bytes_invalid=0 send_seq=3649 receive_seq=3649 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997329 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122622 bytes_read=3612006 bytes_retransmit=9 bytes_invalid=0 send_seq=16429 receive_seq=16429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997782 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=72473 bytes_read=1484424 bytes_retransmit=9 bytes_invalid=0 send_seq=9351 receive_seq=9351 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997666 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22333 bytes_read=895039 bytes_retransmit=9 bytes_invalid=0 send_seq=3663 receive_seq=3663 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997722 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22819 bytes_read=68618 bytes_retransmit=9 bytes_invalid=0 send_seq=3650 receive_seq=3650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999467 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76911 bytes_read=1479867 bytes_retransmit=0 bytes_invalid=0 send_seq=8209 receive_seq=8209 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998739 coil_temp=17.6 refs=0 mcu_temp=20.80 supply_voltage=3.012 th0: temp=44.7 th1: temp=45.4 th2: temp=48.8 th3: temp=46.7 sysload=0.06 cputime=268.554 memavail=7399604 print_time=3539.679 buffer_time=2.063 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 119 Hz
Stats 3516.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20337182 bytes_read=2702965 bytes_retransmit=9 bytes_invalid=0 send_seq=360874 receive_seq=360865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=23 upcoming_bytes=0 freq=400015772 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22072 bytes_read=69985 bytes_retransmit=0 bytes_invalid=0 send_seq=3650 receive_seq=3650 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999215 adj=49996989 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122628 bytes_read=3612120 bytes_retransmit=9 bytes_invalid=0 send_seq=16430 receive_seq=16430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997353 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=72549 bytes_read=1487498 bytes_retransmit=9 bytes_invalid=0 send_seq=9362 receive_seq=9362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997346 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22339 bytes_read=895273 bytes_retransmit=9 bytes_invalid=0 send_seq=3664 receive_seq=3664 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997397 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22825 bytes_read=68634 bytes_retransmit=9 bytes_invalid=0 send_seq=3651 receive_seq=3651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999387 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76917 bytes_read=1480223 bytes_retransmit=0 bytes_invalid=0 send_seq=8210 receive_seq=8210 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998524 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=44.3 th1: temp=45.4 th2: temp=48.9 th3: temp=46.6 sysload=0.06 cputime=268.668 memavail=7398868 print_time=3540.878 buffer_time=2.258 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 120 Hz
Stats 3517.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20341380 bytes_read=2703750 bytes_retransmit=9 bytes_invalid=0 send_seq=360960 receive_seq=360960 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015753 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22078 bytes_read=70014 bytes_retransmit=0 bytes_invalid=0 send_seq=3651 receive_seq=3651 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999223 adj=49997078 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122634 bytes_read=3612248 bytes_retransmit=9 bytes_invalid=0 send_seq=16431 receive_seq=16431 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997555 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=72625 bytes_read=1490570 bytes_retransmit=9 bytes_invalid=0 send_seq=9373 receive_seq=9373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997405 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22345 bytes_read=895552 bytes_retransmit=9 bytes_invalid=0 send_seq=3665 receive_seq=3665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997481 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22831 bytes_read=68661 bytes_retransmit=9 bytes_invalid=0 send_seq=3652 receive_seq=3652 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999408 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76923 bytes_read=1480579 bytes_retransmit=0 bytes_invalid=0 send_seq=8211 receive_seq=8211 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998565 coil_temp=17.6 refs=0 mcu_temp=20.79 supply_voltage=3.012 th0: temp=44.7 th1: temp=45.5 th2: temp=48.6 th3: temp=46.7 sysload=0.06 cputime=268.782 memavail=7398376 print_time=3541.803 buffer_time=2.184 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 121 Hz
Stats 3518.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20344739 bytes_read=2704449 bytes_retransmit=9 bytes_invalid=0 send_seq=361032 receive_seq=361032 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=0 freq=400015766 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22084 bytes_read=70030 bytes_retransmit=0 bytes_invalid=0 send_seq=3652 receive_seq=3652 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999222 adj=49997219 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122640 bytes_read=3612348 bytes_retransmit=9 bytes_invalid=0 send_seq=16432 receive_seq=16432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997599 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=72701 bytes_read=1493640 bytes_retransmit=9 bytes_invalid=0 send_seq=9384 receive_seq=9384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997474 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22351 bytes_read=895816 bytes_retransmit=9 bytes_invalid=0 send_seq=3666 receive_seq=3666 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999527 adj=47997529 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22837 bytes_read=68677 bytes_retransmit=9 bytes_invalid=0 send_seq=3653 receive_seq=3653 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999423 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76929 bytes_read=1480935 bytes_retransmit=0 bytes_invalid=0 send_seq=8212 receive_seq=8212 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998600 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.3 th1: temp=45.3 th2: temp=49.0 th3: temp=46.6 sysload=0.06 cputime=268.881 memavail=7398376 print_time=3542.683 buffer_time=2.063 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 122 Hz
Stats 3519.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20349686 bytes_read=2705234 bytes_retransmit=9 bytes_invalid=0 send_seq=361127 receive_seq=361127 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015758 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22090 bytes_read=70046 bytes_retransmit=0 bytes_invalid=0 send_seq=3653 receive_seq=3653 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999221 adj=49997192 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122646 bytes_read=3612448 bytes_retransmit=9 bytes_invalid=0 send_seq=16433 receive_seq=16433 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997570 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=72777 bytes_read=1496699 bytes_retransmit=9 bytes_invalid=0 send_seq=9395 receive_seq=9395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997436 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22357 bytes_read=896050 bytes_retransmit=9 bytes_invalid=0 send_seq=3667 receive_seq=3667 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997523 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22843 bytes_read=68693 bytes_retransmit=9 bytes_invalid=0 send_seq=3654 receive_seq=3654 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999418 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76935 bytes_read=1481291 bytes_retransmit=0 bytes_invalid=0 send_seq=8213 receive_seq=8213 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998610 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.5 th1: temp=45.5 th2: temp=48.9 th3: temp=46.7 sysload=0.06 cputime=268.995 memavail=7398376 print_time=3543.877 buffer_time=2.256 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 123 Hz
Stats 3520.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20354026 bytes_read=2706000 bytes_retransmit=9 bytes_invalid=0 send_seq=361215 receive_seq=361215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=0 freq=400015742 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22096 bytes_read=70062 bytes_retransmit=0 bytes_invalid=0 send_seq=3654 receive_seq=3654 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999220 adj=49997215 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122652 bytes_read=3612576 bytes_retransmit=9 bytes_invalid=0 send_seq=16434 receive_seq=16434 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997676 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=72853 bytes_read=1499769 bytes_retransmit=9 bytes_invalid=0 send_seq=9406 receive_seq=9406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997468 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22363 bytes_read=896314 bytes_retransmit=9 bytes_invalid=0 send_seq=3668 receive_seq=3668 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997572 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22849 bytes_read=68709 bytes_retransmit=9 bytes_invalid=0 send_seq=3655 receive_seq=3655 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999426 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76941 bytes_read=1481647 bytes_retransmit=0 bytes_invalid=0 send_seq=8214 receive_seq=8214 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998621 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.6 th1: temp=45.3 th2: temp=49.0 th3: temp=46.8 sysload=0.06 cputime=269.101 memavail=7398376 print_time=3544.808 buffer_time=2.187 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 124 Hz
Stats 3521.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20357399 bytes_read=2706693 bytes_retransmit=9 bytes_invalid=0 send_seq=361287 receive_seq=361287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=0 freq=400015717 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22102 bytes_read=70078 bytes_retransmit=0 bytes_invalid=0 send_seq=3655 receive_seq=3655 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999219 adj=49997233 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122658 bytes_read=3612690 bytes_retransmit=9 bytes_invalid=0 send_seq=16435 receive_seq=16435 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997690 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=72929 bytes_read=1502858 bytes_retransmit=9 bytes_invalid=0 send_seq=9417 receive_seq=9417 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997491 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22369 bytes_read=896578 bytes_retransmit=9 bytes_invalid=0 send_seq=3669 receive_seq=3669 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997608 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22855 bytes_read=68725 bytes_retransmit=9 bytes_invalid=0 send_seq=3656 receive_seq=3656 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999433 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76947 bytes_read=1482003 bytes_retransmit=0 bytes_invalid=0 send_seq=8215 receive_seq=8215 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998637 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.8 th1: temp=45.2 th2: temp=48.9 th3: temp=46.7 sysload=0.06 cputime=269.205 memavail=7398376 print_time=3545.682 buffer_time=2.061 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 125 Hz
Stats 3522.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20362446 bytes_read=2707503 bytes_retransmit=9 bytes_invalid=0 send_seq=361387 receive_seq=361387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=0 freq=400015698 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22108 bytes_read=70107 bytes_retransmit=0 bytes_invalid=0 send_seq=3656 receive_seq=3656 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999219 adj=49997256 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122664 bytes_read=3612790 bytes_retransmit=9 bytes_invalid=0 send_seq=16436 receive_seq=16436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997729 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=73005 bytes_read=1505972 bytes_retransmit=9 bytes_invalid=0 send_seq=9428 receive_seq=9428 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997533 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22375 bytes_read=896827 bytes_retransmit=9 bytes_invalid=0 send_seq=3670 receive_seq=3670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22861 bytes_read=68752 bytes_retransmit=9 bytes_invalid=0 send_seq=3657 receive_seq=3657 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76953 bytes_read=1482359 bytes_retransmit=0 bytes_invalid=0 send_seq=8216 receive_seq=8216 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998654 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.9 th1: temp=45.4 th2: temp=48.8 th3: temp=46.8 sysload=0.06 cputime=269.329 memavail=7398388 print_time=3546.884 buffer_time=2.258 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 126 Hz
Stats 3523.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20366780 bytes_read=2708248 bytes_retransmit=9 bytes_invalid=0 send_seq=361474 receive_seq=361474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=0 freq=400015681 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22114 bytes_read=70123 bytes_retransmit=0 bytes_invalid=0 send_seq=3657 receive_seq=3657 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999218 adj=49997280 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122670 bytes_read=3612918 bytes_retransmit=9 bytes_invalid=0 send_seq=16437 receive_seq=16437 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997767 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=73081 bytes_read=1509057 bytes_retransmit=9 bytes_invalid=0 send_seq=9439 receive_seq=9439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997564 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22381 bytes_read=897106 bytes_retransmit=9 bytes_invalid=0 send_seq=3671 receive_seq=3671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22867 bytes_read=68768 bytes_retransmit=9 bytes_invalid=0 send_seq=3658 receive_seq=3658 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76959 bytes_read=1482715 bytes_retransmit=0 bytes_invalid=0 send_seq=8217 receive_seq=8217 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998678 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.9 th1: temp=45.5 th2: temp=49.0 th3: temp=46.9 sysload=0.05 cputime=269.441 memavail=7398388 print_time=3547.813 buffer_time=2.186 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 127 Hz
Stats 3524.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20370212 bytes_read=2708957 bytes_retransmit=9 bytes_invalid=0 send_seq=361548 receive_seq=361548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015668 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22120 bytes_read=70139 bytes_retransmit=0 bytes_invalid=0 send_seq=3658 receive_seq=3658 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999218 adj=49997294 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122676 bytes_read=3613018 bytes_retransmit=9 bytes_invalid=0 send_seq=16438 receive_seq=16438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997775 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=73157 bytes_read=1512114 bytes_retransmit=9 bytes_invalid=0 send_seq=9450 receive_seq=9450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997598 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22387 bytes_read=897355 bytes_retransmit=9 bytes_invalid=0 send_seq=3672 receive_seq=3672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997695 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22873 bytes_read=68784 bytes_retransmit=9 bytes_invalid=0 send_seq=3659 receive_seq=3659 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76965 bytes_read=1483071 bytes_retransmit=0 bytes_invalid=0 send_seq=8218 receive_seq=8218 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998687 coil_temp=17.6 refs=0 mcu_temp=20.78 supply_voltage=3.012 th0: temp=44.9 th1: temp=45.7 th2: temp=49.0 th3: temp=46.9 sysload=0.05 cputime=269.546 memavail=7398388 print_time=3548.686 buffer_time=2.059 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 128 Hz
Stats 3525.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20375230 bytes_read=2709773 bytes_retransmit=9 bytes_invalid=0 send_seq=361646 receive_seq=361646 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=0 freq=400015680 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22126 bytes_read=70155 bytes_retransmit=0 bytes_invalid=0 send_seq=3659 receive_seq=3659 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997309 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122682 bytes_read=3613118 bytes_retransmit=9 bytes_invalid=0 send_seq=16439 receive_seq=16439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997810 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=73233 bytes_read=1515170 bytes_retransmit=9 bytes_invalid=0 send_seq=9461 receive_seq=9461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997619 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22393 bytes_read=897589 bytes_retransmit=9 bytes_invalid=0 send_seq=3673 receive_seq=3673 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999528 adj=47997710 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22879 bytes_read=68800 bytes_retransmit=9 bytes_invalid=0 send_seq=3660 receive_seq=3660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999458 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=31.1 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76971 bytes_read=1483427 bytes_retransmit=0 bytes_invalid=0 send_seq=8219 receive_seq=8219 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998704 coil_temp=17.6 refs=0 mcu_temp=20.77 supply_voltage=3.012 th0: temp=44.8 th1: temp=45.6 th2: temp=48.7 th3: temp=46.9 sysload=0.05 cputime=269.664 memavail=7398388 print_time=3549.884 buffer_time=2.257 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 129 Hz
Stats 3526.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20379628 bytes_read=2710523 bytes_retransmit=9 bytes_invalid=0 send_seq=361734 receive_seq=361734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=32 freq=400015673 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22132 bytes_read=70171 bytes_retransmit=0 bytes_invalid=0 send_seq=3660 receive_seq=3660 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999221 adj=49997266 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122688 bytes_read=3613260 bytes_retransmit=9 bytes_invalid=0 send_seq=16440 receive_seq=16440 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997742 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=73309 bytes_read=1518274 bytes_retransmit=9 bytes_invalid=0 send_seq=9472 receive_seq=9472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997566 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22399 bytes_read=897868 bytes_retransmit=9 bytes_invalid=0 send_seq=3674 receive_seq=3674 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22885 bytes_read=68816 bytes_retransmit=9 bytes_invalid=0 send_seq=3661 receive_seq=3661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999458 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76977 bytes_read=1483783 bytes_retransmit=0 bytes_invalid=0 send_seq=8220 receive_seq=8220 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998683 coil_temp=17.6 refs=0 mcu_temp=20.76 supply_voltage=3.012 th0: temp=44.8 th1: temp=45.9 th2: temp=49.2 th3: temp=47.0 sysload=0.05 cputime=269.774 memavail=7398396 print_time=3550.817 buffer_time=2.189 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 130 Hz
Stats 3527.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20383019 bytes_read=2711227 bytes_retransmit=9 bytes_invalid=0 send_seq=361807 receive_seq=361807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=0 freq=400015677 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22138 bytes_read=70200 bytes_retransmit=0 bytes_invalid=0 send_seq=3661 receive_seq=3661 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999219 adj=49997325 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122694 bytes_read=3613360 bytes_retransmit=9 bytes_invalid=0 send_seq=16441 receive_seq=16441 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997732 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=73385 bytes_read=1521332 bytes_retransmit=9 bytes_invalid=0 send_seq=9483 receive_seq=9483 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22405 bytes_read=898132 bytes_retransmit=9 bytes_invalid=0 send_seq=3675 receive_seq=3675 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997692 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22891 bytes_read=68843 bytes_retransmit=9 bytes_invalid=0 send_seq=3662 receive_seq=3662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999472 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76983 bytes_read=1484139 bytes_retransmit=0 bytes_invalid=0 send_seq=8221 receive_seq=8221 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998752 coil_temp=17.6 refs=0 mcu_temp=20.75 supply_voltage=3.012 th0: temp=44.6 th1: temp=45.6 th2: temp=49.2 th3: temp=47.1 sysload=0.05 cputime=269.881 memavail=7398412 print_time=3551.689 buffer_time=2.061 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 131 Hz
Stats 3528.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20388197 bytes_read=2712042 bytes_retransmit=9 bytes_invalid=0 send_seq=361908 receive_seq=361908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=400015684 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22144 bytes_read=70216 bytes_retransmit=0 bytes_invalid=0 send_seq=3662 receive_seq=3662 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999218 adj=49997290 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122700 bytes_read=3613460 bytes_retransmit=9 bytes_invalid=0 send_seq=16442 receive_seq=16442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997707 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=73461 bytes_read=1524448 bytes_retransmit=9 bytes_invalid=0 send_seq=9494 receive_seq=9494 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997555 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22411 bytes_read=898366 bytes_retransmit=9 bytes_invalid=0 send_seq=3676 receive_seq=3676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997689 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22897 bytes_read=68859 bytes_retransmit=9 bytes_invalid=0 send_seq=3663 receive_seq=3663 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999465 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76989 bytes_read=1484495 bytes_retransmit=0 bytes_invalid=0 send_seq=8222 receive_seq=8222 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998734 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=45.0 th1: temp=45.4 th2: temp=49.1 th3: temp=47.0 sysload=0.13 cputime=270.002 memavail=7398412 print_time=3552.893 buffer_time=2.264 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 132 Hz
Stats 3529.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20392476 bytes_read=2712782 bytes_retransmit=9 bytes_invalid=0 send_seq=361994 receive_seq=361994 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=175 freq=400015723 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22150 bytes_read=70232 bytes_retransmit=0 bytes_invalid=0 send_seq=3663 receive_seq=3663 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999219 adj=49997260 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122706 bytes_read=3613588 bytes_retransmit=9 bytes_invalid=0 send_seq=16443 receive_seq=16443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997679 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=73530 bytes_read=1527509 bytes_retransmit=9 bytes_invalid=0 send_seq=9504 receive_seq=9504 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997548 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22417 bytes_read=898645 bytes_retransmit=9 bytes_invalid=0 send_seq=3677 receive_seq=3677 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22903 bytes_read=68875 bytes_retransmit=9 bytes_invalid=0 send_seq=3664 receive_seq=3664 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=76995 bytes_read=1484851 bytes_retransmit=0 bytes_invalid=0 send_seq=8223 receive_seq=8223 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998695 coil_temp=17.6 refs=0 mcu_temp=20.74 supply_voltage=3.012 th0: temp=45.0 th1: temp=45.7 th2: temp=49.0 th3: temp=47.3 sysload=0.13 cputime=270.120 memavail=7397012 print_time=3553.819 buffer_time=2.189 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Stats 3530.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20395767 bytes_read=2713482 bytes_retransmit=9 bytes_invalid=0 send_seq=362063 receive_seq=362063 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015725 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22156 bytes_read=70248 bytes_retransmit=0 bytes_invalid=0 send_seq=3664 receive_seq=3664 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999219 adj=49997204 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122712 bytes_read=3613688 bytes_retransmit=9 bytes_invalid=0 send_seq=16444 receive_seq=16444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997614 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=73606 bytes_read=1530566 bytes_retransmit=9 bytes_invalid=0 send_seq=9515 receive_seq=9515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997477 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22423 bytes_read=898894 bytes_retransmit=9 bytes_invalid=0 send_seq=3678 receive_seq=3678 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999529 adj=47997608 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22909 bytes_read=68891 bytes_retransmit=9 bytes_invalid=0 send_seq=3665 receive_seq=3665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77001 bytes_read=1485207 bytes_retransmit=0 bytes_invalid=0 send_seq=8224 receive_seq=8224 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998647 coil_temp=17.6 refs=0 mcu_temp=20.73 supply_voltage=3.012 th0: temp=44.8 th1: temp=45.6 th2: temp=48.9 th3: temp=47.1 sysload=0.13 cputime=270.217 memavail=7397012 print_time=3554.467 buffer_time=1.837 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 3531.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20396081 bytes_read=2713907 bytes_retransmit=9 bytes_invalid=0 send_seq=362086 receive_seq=362086 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015714 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22162 bytes_read=70263 bytes_retransmit=0 bytes_invalid=0 send_seq=3665 receive_seq=3665 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999218 adj=49997204 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122718 bytes_read=3613802 bytes_retransmit=9 bytes_invalid=0 send_seq=16445 receive_seq=16445 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997600 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=73682 bytes_read=1533640 bytes_retransmit=9 bytes_invalid=0 send_seq=9526 receive_seq=9526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997468 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22429 bytes_read=899128 bytes_retransmit=9 bytes_invalid=0 send_seq=3679 receive_seq=3679 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999530 adj=47997605 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22915 bytes_read=68907 bytes_retransmit=9 bytes_invalid=0 send_seq=3666 receive_seq=3666 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.6 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77007 bytes_read=1485563 bytes_retransmit=0 bytes_invalid=0 send_seq=8225 receive_seq=8225 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998644 coil_temp=17.6 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=45.0 th1: temp=45.6 th2: temp=48.5 th3: temp=46.8 sysload=0.13 cputime=270.282 memavail=7397012 print_time=3554.467 buffer_time=0.837 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Writing raw accelerometer data to /tmp/raw_data_x_toolboard_t1_t1.csv file
RatOS | IDEX:: Selecting T0..
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 20.000000
RatOS | IDEX:: Toolhead offset applied for T0: X=0 Y=0 Z=0
Activating extruder extruder
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
Probing point (250.000, 250.000, 20.000)
LIS2DW finished 'toolboard_t1' measurements
Stats 3532.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20399134 bytes_read=2714553 bytes_retransmit=9 bytes_invalid=0 send_seq=362154 receive_seq=362154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=0 freq=400015709 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22168 bytes_read=70291 bytes_retransmit=0 bytes_invalid=0 send_seq=3666 receive_seq=3666 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997210 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122724 bytes_read=3613930 bytes_retransmit=9 bytes_invalid=0 send_seq=16446 receive_seq=16446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997623 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=73806 bytes_read=1536770 bytes_retransmit=9 bytes_invalid=0 send_seq=9542 receive_seq=9542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997482 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22435 bytes_read=899422 bytes_retransmit=9 bytes_invalid=0 send_seq=3680 receive_seq=3680 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999531 adj=47997629 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22921 bytes_read=68934 bytes_retransmit=9 bytes_invalid=0 send_seq=3667 receive_seq=3667 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77013 bytes_read=1485919 bytes_retransmit=0 bytes_invalid=0 send_seq=8226 receive_seq=8226 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998668 coil_temp=17.6 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=45.0 th1: temp=45.6 th2: temp=49.0 th3: temp=47.0 sysload=0.13 cputime=270.466 memavail=7381156 print_time=3555.771 buffer_time=1.137 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3533.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20399460 bytes_read=2715007 bytes_retransmit=9 bytes_invalid=0 send_seq=362177 receive_seq=362177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015715 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22174 bytes_read=70306 bytes_retransmit=0 bytes_invalid=0 send_seq=3667 receive_seq=3667 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997197 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122730 bytes_read=3614026 bytes_retransmit=9 bytes_invalid=0 send_seq=16447 receive_seq=16447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997626 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=73812 bytes_read=1536866 bytes_retransmit=9 bytes_invalid=0 send_seq=9543 receive_seq=9543 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997485 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22441 bytes_read=899671 bytes_retransmit=9 bytes_invalid=0 send_seq=3681 receive_seq=3681 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22927 bytes_read=68950 bytes_retransmit=9 bytes_invalid=0 send_seq=3668 receive_seq=3668 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77019 bytes_read=1486275 bytes_retransmit=0 bytes_invalid=0 send_seq=8227 receive_seq=8227 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998655 coil_temp=17.6 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=44.7 th1: temp=45.6 th2: temp=49.1 th3: temp=47.0 sysload=0.12 cputime=270.519 memavail=7396940 print_time=3555.771 buffer_time=0.136 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t0' measurements
toolhead: max_velocity: 600.000000
max_accel: 8379.841000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance testing
Testing frequency 10 Hz
Testing frequency 11 Hz
Testing frequency 12 Hz
Stats 3534.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20402056 bytes_read=2715617 bytes_retransmit=9 bytes_invalid=0 send_seq=362237 receive_seq=362237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015700 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22180 bytes_read=70321 bytes_retransmit=0 bytes_invalid=0 send_seq=3668 receive_seq=3668 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997202 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122899 bytes_read=3616574 bytes_retransmit=9 bytes_invalid=0 send_seq=16467 receive_seq=16467 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997655 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=73818 bytes_read=1536959 bytes_retransmit=9 bytes_invalid=0 send_seq=9544 receive_seq=9544 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997465 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22447 bytes_read=899905 bytes_retransmit=9 bytes_invalid=0 send_seq=3682 receive_seq=3682 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22933 bytes_read=68966 bytes_retransmit=9 bytes_invalid=0 send_seq=3669 receive_seq=3669 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77025 bytes_read=1486631 bytes_retransmit=0 bytes_invalid=0 send_seq=8228 receive_seq=8228 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998658 coil_temp=17.6 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=44.9 th1: temp=45.5 th2: temp=49.3 th3: temp=47.1 sysload=0.12 cputime=270.681 memavail=7396940 print_time=3558.940 buffer_time=2.305 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 13 Hz
Stats 3535.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20403128 bytes_read=2716117 bytes_retransmit=9 bytes_invalid=0 send_seq=362272 receive_seq=362272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=0 freq=400015691 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22186 bytes_read=70336 bytes_retransmit=0 bytes_invalid=0 send_seq=3669 receive_seq=3669 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997267 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=122968 bytes_read=3619563 bytes_retransmit=9 bytes_invalid=0 send_seq=16477 receive_seq=16477 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997747 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=73824 bytes_read=1537078 bytes_retransmit=9 bytes_invalid=0 send_seq=9545 receive_seq=9545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997550 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22453 bytes_read=900184 bytes_retransmit=9 bytes_invalid=0 send_seq=3683 receive_seq=3683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22939 bytes_read=68982 bytes_retransmit=9 bytes_invalid=0 send_seq=3670 receive_seq=3670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77031 bytes_read=1486987 bytes_retransmit=0 bytes_invalid=0 send_seq=8229 receive_seq=8229 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998723 coil_temp=17.6 refs=0 mcu_temp=20.73 supply_voltage=3.012 th0: temp=45.2 th1: temp=45.4 th2: temp=49.3 th3: temp=47.1 sysload=0.12 cputime=270.750 memavail=7396944 print_time=3559.783 buffer_time=2.148 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 14 Hz
Stats 3536.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20404635 bytes_read=2716651 bytes_retransmit=9 bytes_invalid=0 send_seq=362311 receive_seq=362311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015695 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22192 bytes_read=70352 bytes_retransmit=0 bytes_invalid=0 send_seq=3670 receive_seq=3670 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997272 toolboard_t0: mcu_awake=0.136 mcu_task_avg=0.000108 mcu_task_stddev=0.000072 bytes_write=123044 bytes_read=3622605 bytes_retransmit=9 bytes_invalid=0 send_seq=16488 receive_seq=16488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997844 toolboard_t1: mcu_awake=0.087 mcu_task_avg=0.000102 mcu_task_stddev=0.000074 bytes_write=73830 bytes_read=1537188 bytes_retransmit=9 bytes_invalid=0 send_seq=9546 receive_seq=9546 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997557 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22459 bytes_read=900433 bytes_retransmit=9 bytes_invalid=0 send_seq=3684 receive_seq=3684 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997690 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22945 bytes_read=68998 bytes_retransmit=9 bytes_invalid=0 send_seq=3671 receive_seq=3671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77037 bytes_read=1487343 bytes_retransmit=0 bytes_invalid=0 send_seq=8230 receive_seq=8230 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998719 coil_temp=17.6 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=44.9 th1: temp=45.1 th2: temp=49.0 th3: temp=47.1 sysload=0.12 cputime=270.821 memavail=7397268 print_time=3560.806 buffer_time=2.170 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 15 Hz
Stats 3537.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20405790 bytes_read=2717141 bytes_retransmit=9 bytes_invalid=0 send_seq=362347 receive_seq=362347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=0 freq=400015683 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=22198 bytes_read=70381 bytes_retransmit=0 bytes_invalid=0 send_seq=3671 receive_seq=3671 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997255 toolboard_t0: mcu_awake=0.136 mcu_task_avg=0.000108 mcu_task_stddev=0.000072 bytes_write=123120 bytes_read=3625650 bytes_retransmit=9 bytes_invalid=0 send_seq=16499 receive_seq=16499 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997895 toolboard_t1: mcu_awake=0.087 mcu_task_avg=0.000102 mcu_task_stddev=0.000074 bytes_write=73836 bytes_read=1537283 bytes_retransmit=9 bytes_invalid=0 send_seq=9547 receive_seq=9547 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22465 bytes_read=900682 bytes_retransmit=9 bytes_invalid=0 send_seq=3685 receive_seq=3685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997679 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22951 bytes_read=69025 bytes_retransmit=9 bytes_invalid=0 send_seq=3672 receive_seq=3672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77043 bytes_read=1487683 bytes_retransmit=0 bytes_invalid=0 send_seq=8231 receive_seq=8231 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998754 coil_temp=17.6 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=45.0 th1: temp=45.2 th2: temp=49.2 th3: temp=47.0 sysload=0.12 cputime=270.893 memavail=7397268 print_time=3561.660 buffer_time=2.024 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 16 Hz
Stats 3538.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20407570 bytes_read=2717681 bytes_retransmit=9 bytes_invalid=0 send_seq=362393 receive_seq=362393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015682 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=22204 bytes_read=70397 bytes_retransmit=0 bytes_invalid=0 send_seq=3672 receive_seq=3672 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999215 adj=49997271 toolboard_t0: mcu_awake=0.136 mcu_task_avg=0.000108 mcu_task_stddev=0.000072 bytes_write=123196 bytes_read=3628735 bytes_retransmit=9 bytes_invalid=0 send_seq=16510 receive_seq=16510 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997875 toolboard_t1: mcu_awake=0.087 mcu_task_avg=0.000102 mcu_task_stddev=0.000074 bytes_write=73842 bytes_read=1537411 bytes_retransmit=9 bytes_invalid=0 send_seq=9548 receive_seq=9548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997555 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22471 bytes_read=900961 bytes_retransmit=9 bytes_invalid=0 send_seq=3686 receive_seq=3686 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997757 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22957 bytes_read=69041 bytes_retransmit=9 bytes_invalid=0 send_seq=3673 receive_seq=3673 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.5 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77049 bytes_read=1488039 bytes_retransmit=0 bytes_invalid=0 send_seq=8232 receive_seq=8232 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998740 coil_temp=17.6 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=44.8 th1: temp=44.4 th2: temp=49.4 th3: temp=47.1 sysload=0.11 cputime=270.968 memavail=7397268 print_time=3562.919 buffer_time=2.282 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 17 Hz
Stats 3539.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20409133 bytes_read=2718230 bytes_retransmit=9 bytes_invalid=0 send_seq=362435 receive_seq=362435 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=0 freq=400015688 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=22210 bytes_read=70413 bytes_retransmit=0 bytes_invalid=0 send_seq=3673 receive_seq=3673 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999215 adj=49997256 toolboard_t0: mcu_awake=0.136 mcu_task_avg=0.000108 mcu_task_stddev=0.000072 bytes_write=123272 bytes_read=3631851 bytes_retransmit=9 bytes_invalid=0 send_seq=16521 receive_seq=16521 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997794 toolboard_t1: mcu_awake=0.087 mcu_task_avg=0.000102 mcu_task_stddev=0.000074 bytes_write=73848 bytes_read=1537511 bytes_retransmit=9 bytes_invalid=0 send_seq=9549 receive_seq=9549 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997542 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22477 bytes_read=901210 bytes_retransmit=9 bytes_invalid=0 send_seq=3687 receive_seq=3687 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997736 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22963 bytes_read=69057 bytes_retransmit=9 bytes_invalid=0 send_seq=3674 receive_seq=3674 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77055 bytes_read=1488395 bytes_retransmit=0 bytes_invalid=0 send_seq=8233 receive_seq=8233 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998712 coil_temp=17.6 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=45.2 th1: temp=45.0 th2: temp=49.1 th3: temp=47.0 sysload=0.11 cputime=271.041 memavail=7397268 print_time=3563.829 buffer_time=2.191 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 18 Hz
Stats 3540.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20410507 bytes_read=2718750 bytes_retransmit=9 bytes_invalid=0 send_seq=362474 receive_seq=362474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=47 upcoming_bytes=0 freq=400015695 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=22216 bytes_read=70429 bytes_retransmit=0 bytes_invalid=0 send_seq=3674 receive_seq=3674 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997247 toolboard_t0: mcu_awake=0.136 mcu_task_avg=0.000108 mcu_task_stddev=0.000072 bytes_write=123348 bytes_read=3634909 bytes_retransmit=9 bytes_invalid=0 send_seq=16532 receive_seq=16532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997755 toolboard_t1: mcu_awake=0.087 mcu_task_avg=0.000102 mcu_task_stddev=0.000074 bytes_write=73854 bytes_read=1537611 bytes_retransmit=9 bytes_invalid=0 send_seq=9550 receive_seq=9550 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22483 bytes_read=901444 bytes_retransmit=9 bytes_invalid=0 send_seq=3688 receive_seq=3688 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997713 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22969 bytes_read=69073 bytes_retransmit=9 bytes_invalid=0 send_seq=3675 receive_seq=3675 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77061 bytes_read=1488751 bytes_retransmit=0 bytes_invalid=0 send_seq=8234 receive_seq=8234 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998688 coil_temp=17.5 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=44.7 th1: temp=44.8 th2: temp=49.3 th3: temp=47.2 sysload=0.11 cputime=271.112 memavail=7397268 print_time=3564.775 buffer_time=2.136 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 19 Hz
Stats 3541.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20412442 bytes_read=2719300 bytes_retransmit=9 bytes_invalid=0 send_seq=362522 receive_seq=362522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=0 freq=400015703 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=22222 bytes_read=70445 bytes_retransmit=0 bytes_invalid=0 send_seq=3675 receive_seq=3675 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997219 toolboard_t0: mcu_awake=0.316 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=123424 bytes_read=3638012 bytes_retransmit=9 bytes_invalid=0 send_seq=16543 receive_seq=16543 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997715 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=73860 bytes_read=1537753 bytes_retransmit=9 bytes_invalid=0 send_seq=9551 receive_seq=9551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22489 bytes_read=901738 bytes_retransmit=9 bytes_invalid=0 send_seq=3689 receive_seq=3689 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997689 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22975 bytes_read=69089 bytes_retransmit=9 bytes_invalid=0 send_seq=3676 receive_seq=3676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77067 bytes_read=1489107 bytes_retransmit=0 bytes_invalid=0 send_seq=8235 receive_seq=8235 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998667 coil_temp=17.5 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=45.0 th1: temp=44.7 th2: temp=49.2 th3: temp=47.1 sysload=0.11 cputime=271.188 memavail=7397268 print_time=3565.986 buffer_time=2.348 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 20 Hz
Stats 3542.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20414132 bytes_read=2719857 bytes_retransmit=9 bytes_invalid=0 send_seq=362566 receive_seq=362566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=0 freq=400015705 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22228 bytes_read=70474 bytes_retransmit=0 bytes_invalid=0 send_seq=3676 receive_seq=3676 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997212 toolboard_t0: mcu_awake=0.316 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=123500 bytes_read=3641071 bytes_retransmit=9 bytes_invalid=0 send_seq=16554 receive_seq=16554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997773 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=73866 bytes_read=1537853 bytes_retransmit=9 bytes_invalid=0 send_seq=9552 receive_seq=9552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22495 bytes_read=901987 bytes_retransmit=9 bytes_invalid=0 send_seq=3690 receive_seq=3690 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22981 bytes_read=69116 bytes_retransmit=9 bytes_invalid=0 send_seq=3677 receive_seq=3677 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77073 bytes_read=1489463 bytes_retransmit=0 bytes_invalid=0 send_seq=8236 receive_seq=8236 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998649 coil_temp=17.5 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=45.2 th1: temp=44.8 th2: temp=49.2 th3: temp=47.2 sysload=0.11 cputime=271.262 memavail=7397268 print_time=3566.857 buffer_time=2.217 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 21 Hz
Stats 3543.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20415717 bytes_read=2720390 bytes_retransmit=9 bytes_invalid=0 send_seq=362609 receive_seq=362609 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015699 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22240 bytes_read=70506 bytes_retransmit=0 bytes_invalid=0 send_seq=3678 receive_seq=3678 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997221 toolboard_t0: mcu_awake=0.316 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=123582 bytes_read=3644144 bytes_retransmit=9 bytes_invalid=0 send_seq=16566 receive_seq=16566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997755 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=73878 bytes_read=1537969 bytes_retransmit=9 bytes_invalid=0 send_seq=9554 receive_seq=9554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997491 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22507 bytes_read=902237 bytes_retransmit=9 bytes_invalid=0 send_seq=3692 receive_seq=3692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22993 bytes_read=69148 bytes_retransmit=9 bytes_invalid=0 send_seq=3679 receive_seq=3679 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77085 bytes_read=1489835 bytes_retransmit=0 bytes_invalid=0 send_seq=8238 receive_seq=8238 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998633 coil_temp=17.5 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=45.1 th1: temp=44.9 th2: temp=49.3 th3: temp=47.1 sysload=0.10 cputime=271.337 memavail=7397268 print_time=3567.821 buffer_time=2.181 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 22 Hz
Stats 3544.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20417413 bytes_read=2720915 bytes_retransmit=9 bytes_invalid=0 send_seq=362652 receive_seq=362652 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015705 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22246 bytes_read=70522 bytes_retransmit=0 bytes_invalid=0 send_seq=3679 receive_seq=3679 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997232 toolboard_t0: mcu_awake=0.316 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=123658 bytes_read=3647231 bytes_retransmit=9 bytes_invalid=0 send_seq=16577 receive_seq=16577 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997700 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=73884 bytes_read=1538097 bytes_retransmit=9 bytes_invalid=0 send_seq=9555 receive_seq=9555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997597 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22513 bytes_read=902531 bytes_retransmit=9 bytes_invalid=0 send_seq=3693 receive_seq=3693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=22999 bytes_read=69164 bytes_retransmit=9 bytes_invalid=0 send_seq=3680 receive_seq=3680 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77091 bytes_read=1490191 bytes_retransmit=0 bytes_invalid=0 send_seq=8239 receive_seq=8239 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998649 coil_temp=17.5 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=45.3 th1: temp=44.7 th2: temp=49.2 th3: temp=47.3 sysload=0.10 cputime=271.412 memavail=7397304 print_time=3568.676 buffer_time=2.035 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 23 Hz
Stats 3545.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20419559 bytes_read=2721524 bytes_retransmit=9 bytes_invalid=0 send_seq=362703 receive_seq=362703 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015710 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22252 bytes_read=70538 bytes_retransmit=0 bytes_invalid=0 send_seq=3680 receive_seq=3680 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999214 adj=49997215 toolboard_t0: mcu_awake=0.316 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=123734 bytes_read=3650287 bytes_retransmit=9 bytes_invalid=0 send_seq=16588 receive_seq=16588 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997861 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=73890 bytes_read=1538197 bytes_retransmit=9 bytes_invalid=0 send_seq=9556 receive_seq=9556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997581 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22519 bytes_read=902765 bytes_retransmit=9 bytes_invalid=0 send_seq=3694 receive_seq=3694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23005 bytes_read=69180 bytes_retransmit=9 bytes_invalid=0 send_seq=3681 receive_seq=3681 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77097 bytes_read=1490547 bytes_retransmit=0 bytes_invalid=0 send_seq=8240 receive_seq=8240 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998632 coil_temp=17.5 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=44.9 th1: temp=44.8 th2: temp=49.0 th3: temp=47.3 sysload=0.10 cputime=271.493 memavail=7397304 print_time=3569.866 buffer_time=2.226 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 24 Hz
Stats 3546.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20421190 bytes_read=2722049 bytes_retransmit=9 bytes_invalid=0 send_seq=362746 receive_seq=362746 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015713 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22258 bytes_read=70554 bytes_retransmit=0 bytes_invalid=0 send_seq=3681 receive_seq=3681 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997236 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=123810 bytes_read=3653418 bytes_retransmit=9 bytes_invalid=0 send_seq=16599 receive_seq=16599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997773 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=73896 bytes_read=1538311 bytes_retransmit=9 bytes_invalid=0 send_seq=9557 receive_seq=9557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22525 bytes_read=902999 bytes_retransmit=9 bytes_invalid=0 send_seq=3695 receive_seq=3695 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23011 bytes_read=69196 bytes_retransmit=9 bytes_invalid=0 send_seq=3682 receive_seq=3682 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77103 bytes_read=1490903 bytes_retransmit=0 bytes_invalid=0 send_seq=8241 receive_seq=8241 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998635 coil_temp=17.5 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=45.3 th1: temp=44.7 th2: temp=49.2 th3: temp=47.2 sysload=0.10 cputime=271.580 memavail=7390796 print_time=3570.829 buffer_time=2.188 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 25 Hz
Stats 3547.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20423049 bytes_read=2722594 bytes_retransmit=9 bytes_invalid=0 send_seq=362793 receive_seq=362793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015716 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22264 bytes_read=70583 bytes_retransmit=0 bytes_invalid=0 send_seq=3682 receive_seq=3682 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997225 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=123886 bytes_read=3656502 bytes_retransmit=9 bytes_invalid=0 send_seq=16610 receive_seq=16610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997727 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=73902 bytes_read=1538439 bytes_retransmit=9 bytes_invalid=0 send_seq=9558 receive_seq=9558 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22531 bytes_read=903308 bytes_retransmit=9 bytes_invalid=0 send_seq=3696 receive_seq=3696 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23017 bytes_read=69223 bytes_retransmit=9 bytes_invalid=0 send_seq=3683 receive_seq=3683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999462 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77109 bytes_read=1491259 bytes_retransmit=0 bytes_invalid=0 send_seq=8242 receive_seq=8242 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998654 coil_temp=17.5 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=45.3 th1: temp=44.7 th2: temp=49.4 th3: temp=47.1 sysload=0.10 cputime=271.659 memavail=7396892 print_time=3571.706 buffer_time=2.064 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 26 Hz
Stats 3548.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20424858 bytes_read=2723163 bytes_retransmit=9 bytes_invalid=0 send_seq=362839 receive_seq=362839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015701 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22270 bytes_read=70599 bytes_retransmit=0 bytes_invalid=0 send_seq=3683 receive_seq=3683 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997209 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=123962 bytes_read=3659559 bytes_retransmit=9 bytes_invalid=0 send_seq=16621 receive_seq=16621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997720 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=73908 bytes_read=1538539 bytes_retransmit=9 bytes_invalid=0 send_seq=9559 receive_seq=9559 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997534 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22537 bytes_read=903542 bytes_retransmit=9 bytes_invalid=0 send_seq=3697 receive_seq=3697 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23023 bytes_read=69239 bytes_retransmit=9 bytes_invalid=0 send_seq=3684 receive_seq=3684 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999456 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77115 bytes_read=1491615 bytes_retransmit=0 bytes_invalid=0 send_seq=8243 receive_seq=8243 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998639 coil_temp=17.5 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=45.4 th1: temp=44.4 th2: temp=49.1 th3: temp=47.2 sysload=0.09 cputime=271.740 memavail=7396892 print_time=3572.673 buffer_time=2.030 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 27 Hz
Stats 3549.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20427182 bytes_read=2723748 bytes_retransmit=9 bytes_invalid=0 send_seq=362894 receive_seq=362894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015689 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22276 bytes_read=70615 bytes_retransmit=0 bytes_invalid=0 send_seq=3684 receive_seq=3684 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997235 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124038 bytes_read=3662621 bytes_retransmit=9 bytes_invalid=0 send_seq=16632 receive_seq=16632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997714 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=73914 bytes_read=1538639 bytes_retransmit=9 bytes_invalid=0 send_seq=9560 receive_seq=9560 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22543 bytes_read=903776 bytes_retransmit=9 bytes_invalid=0 send_seq=3698 receive_seq=3698 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23029 bytes_read=69255 bytes_retransmit=9 bytes_invalid=0 send_seq=3685 receive_seq=3685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999459 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77121 bytes_read=1491971 bytes_retransmit=0 bytes_invalid=0 send_seq=8244 receive_seq=8244 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998652 coil_temp=17.5 refs=0 mcu_temp=20.70 supply_voltage=3.012 th0: temp=45.4 th1: temp=44.4 th2: temp=49.2 th3: temp=47.2 sysload=0.09 cputime=271.824 memavail=7396668 print_time=3573.882 buffer_time=2.238 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 28 Hz
Stats 3550.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20428926 bytes_read=2724293 bytes_retransmit=9 bytes_invalid=0 send_seq=362938 receive_seq=362938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015685 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22282 bytes_read=70631 bytes_retransmit=0 bytes_invalid=0 send_seq=3685 receive_seq=3685 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997254 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124114 bytes_read=3665708 bytes_retransmit=9 bytes_invalid=0 send_seq=16643 receive_seq=16643 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997708 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=73920 bytes_read=1538767 bytes_retransmit=9 bytes_invalid=0 send_seq=9561 receive_seq=9561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997567 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22549 bytes_read=904070 bytes_retransmit=9 bytes_invalid=0 send_seq=3699 receive_seq=3699 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23035 bytes_read=69271 bytes_retransmit=9 bytes_invalid=0 send_seq=3686 receive_seq=3686 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999458 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77127 bytes_read=1492327 bytes_retransmit=0 bytes_invalid=0 send_seq=8245 receive_seq=8245 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998670 coil_temp=17.5 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=45.1 th1: temp=44.8 th2: temp=49.1 th3: temp=47.3 sysload=0.09 cputime=271.898 memavail=7396668 print_time=3574.757 buffer_time=2.113 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 29 Hz
Stats 3551.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20430795 bytes_read=2724867 bytes_retransmit=9 bytes_invalid=0 send_seq=362985 receive_seq=362985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015696 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22288 bytes_read=70647 bytes_retransmit=0 bytes_invalid=0 send_seq=3686 receive_seq=3686 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997262 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124183 bytes_read=3668759 bytes_retransmit=9 bytes_invalid=0 send_seq=16653 receive_seq=16653 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997716 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=73926 bytes_read=1538881 bytes_retransmit=9 bytes_invalid=0 send_seq=9562 receive_seq=9562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997573 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22555 bytes_read=904304 bytes_retransmit=9 bytes_invalid=0 send_seq=3700 receive_seq=3700 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23041 bytes_read=69287 bytes_retransmit=9 bytes_invalid=0 send_seq=3687 receive_seq=3687 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999464 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77133 bytes_read=1492683 bytes_retransmit=0 bytes_invalid=0 send_seq=8246 receive_seq=8246 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998669 coil_temp=17.5 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=45.8 th1: temp=44.5 th2: temp=49.3 th3: temp=47.4 sysload=0.09 cputime=271.974 memavail=7396680 print_time=3575.682 buffer_time=2.037 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 30 Hz
Stats 3552.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20433220 bytes_read=2725462 bytes_retransmit=9 bytes_invalid=0 send_seq=363042 receive_seq=363042 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=0 freq=400015688 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22294 bytes_read=70676 bytes_retransmit=0 bytes_invalid=0 send_seq=3687 receive_seq=3687 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997254 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124259 bytes_read=3671816 bytes_retransmit=9 bytes_invalid=0 send_seq=16664 receive_seq=16664 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997673 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=73932 bytes_read=1538981 bytes_retransmit=9 bytes_invalid=0 send_seq=9563 receive_seq=9563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997552 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22561 bytes_read=904553 bytes_retransmit=9 bytes_invalid=0 send_seq=3701 receive_seq=3701 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23047 bytes_read=69314 bytes_retransmit=9 bytes_invalid=0 send_seq=3688 receive_seq=3688 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999455 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77139 bytes_read=1493039 bytes_retransmit=0 bytes_invalid=0 send_seq=8247 receive_seq=8247 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998703 coil_temp=17.5 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=45.1 th1: temp=44.7 th2: temp=49.2 th3: temp=47.3 sysload=0.09 cputime=272.055 memavail=7396680 print_time=3576.903 buffer_time=2.258 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 31 Hz
Stats 3553.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20434996 bytes_read=2725999 bytes_retransmit=9 bytes_invalid=0 send_seq=363088 receive_seq=363088 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015676 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22300 bytes_read=70692 bytes_retransmit=0 bytes_invalid=0 send_seq=3688 receive_seq=3688 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997247 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124335 bytes_read=3674900 bytes_retransmit=9 bytes_invalid=0 send_seq=16675 receive_seq=16675 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997679 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=73938 bytes_read=1539109 bytes_retransmit=9 bytes_invalid=0 send_seq=9564 receive_seq=9564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997565 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22567 bytes_read=904847 bytes_retransmit=9 bytes_invalid=0 send_seq=3702 receive_seq=3702 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23053 bytes_read=69330 bytes_retransmit=9 bytes_invalid=0 send_seq=3689 receive_seq=3689 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999453 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77145 bytes_read=1493395 bytes_retransmit=0 bytes_invalid=0 send_seq=8248 receive_seq=8248 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998688 coil_temp=17.5 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=45.4 th1: temp=44.4 th2: temp=49.4 th3: temp=47.3 sysload=0.08 cputime=272.131 memavail=7396680 print_time=3577.765 buffer_time=2.119 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 32 Hz
Stats 3554.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20437095 bytes_read=2726591 bytes_retransmit=9 bytes_invalid=0 send_seq=363139 receive_seq=363139 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015674 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22306 bytes_read=70708 bytes_retransmit=0 bytes_invalid=0 send_seq=3689 receive_seq=3689 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997286 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124411 bytes_read=3678014 bytes_retransmit=9 bytes_invalid=0 send_seq=16686 receive_seq=16686 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997688 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=73944 bytes_read=1539209 bytes_retransmit=9 bytes_invalid=0 send_seq=9565 receive_seq=9565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997604 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22573 bytes_read=905081 bytes_retransmit=9 bytes_invalid=0 send_seq=3703 receive_seq=3703 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997704 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23059 bytes_read=69346 bytes_retransmit=9 bytes_invalid=0 send_seq=3690 receive_seq=3690 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999463 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77151 bytes_read=1493751 bytes_retransmit=0 bytes_invalid=0 send_seq=8249 receive_seq=8249 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998686 coil_temp=17.5 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=45.9 th1: temp=44.5 th2: temp=49.5 th3: temp=47.3 sysload=0.08 cputime=272.207 memavail=7396680 print_time=3578.705 buffer_time=2.059 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 33 Hz
Stats 3555.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20439675 bytes_read=2727211 bytes_retransmit=9 bytes_invalid=0 send_seq=363198 receive_seq=363198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=0 freq=400015669 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22312 bytes_read=70724 bytes_retransmit=0 bytes_invalid=0 send_seq=3690 receive_seq=3690 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997282 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124487 bytes_read=3681071 bytes_retransmit=9 bytes_invalid=0 send_seq=16697 receive_seq=16697 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997781 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=73950 bytes_read=1539309 bytes_retransmit=9 bytes_invalid=0 send_seq=9566 receive_seq=9566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997600 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22579 bytes_read=905311 bytes_retransmit=9 bytes_invalid=0 send_seq=3704 receive_seq=3704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23065 bytes_read=69362 bytes_retransmit=9 bytes_invalid=0 send_seq=3691 receive_seq=3691 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999480 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77157 bytes_read=1494107 bytes_retransmit=0 bytes_invalid=0 send_seq=8250 receive_seq=8250 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998684 coil_temp=17.5 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=45.6 th1: temp=44.7 th2: temp=49.3 th3: temp=47.4 sysload=0.08 cputime=272.289 memavail=7396680 print_time=3579.950 buffer_time=2.304 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 34 Hz
Stats 3556.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20441448 bytes_read=2727746 bytes_retransmit=9 bytes_invalid=0 send_seq=363243 receive_seq=363243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=0 freq=400015685 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22318 bytes_read=70740 bytes_retransmit=0 bytes_invalid=0 send_seq=3691 receive_seq=3691 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997273 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124563 bytes_read=3684173 bytes_retransmit=9 bytes_invalid=0 send_seq=16708 receive_seq=16708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997744 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=73956 bytes_read=1539451 bytes_retransmit=9 bytes_invalid=0 send_seq=9567 receive_seq=9567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997584 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22585 bytes_read=905582 bytes_retransmit=9 bytes_invalid=0 send_seq=3705 receive_seq=3705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997739 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23071 bytes_read=69378 bytes_retransmit=9 bytes_invalid=0 send_seq=3692 receive_seq=3692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999468 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77163 bytes_read=1494463 bytes_retransmit=0 bytes_invalid=0 send_seq=8251 receive_seq=8251 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998705 coil_temp=17.5 refs=0 mcu_temp=20.72 supply_voltage=3.012 th0: temp=45.6 th1: temp=44.3 th2: temp=49.5 th3: temp=47.4 sysload=0.08 cputime=272.367 memavail=7396440 print_time=3580.823 buffer_time=2.176 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 35 Hz
Stats 3557.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20443782 bytes_read=2728360 bytes_retransmit=9 bytes_invalid=0 send_seq=363298 receive_seq=363298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015701 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22324 bytes_read=70769 bytes_retransmit=0 bytes_invalid=0 send_seq=3692 receive_seq=3692 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997234 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124639 bytes_read=3687232 bytes_retransmit=9 bytes_invalid=0 send_seq=16719 receive_seq=16719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997705 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=73962 bytes_read=1539551 bytes_retransmit=9 bytes_invalid=0 send_seq=9568 receive_seq=9568 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997536 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22591 bytes_read=905815 bytes_retransmit=9 bytes_invalid=0 send_seq=3706 receive_seq=3706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997705 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23077 bytes_read=69405 bytes_retransmit=9 bytes_invalid=0 send_seq=3693 receive_seq=3693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999457 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77169 bytes_read=1494819 bytes_retransmit=0 bytes_invalid=0 send_seq=8252 receive_seq=8252 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998683 coil_temp=17.5 refs=0 mcu_temp=20.71 supply_voltage=3.012 th0: temp=45.6 th1: temp=44.3 th2: temp=49.3 th3: temp=47.3 sysload=0.08 cputime=272.445 memavail=7396440 print_time=3581.753 buffer_time=2.106 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 36 Hz
Stats 3558.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20446436 bytes_read=2728975 bytes_retransmit=9 bytes_invalid=0 send_seq=363359 receive_seq=363359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015695 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22330 bytes_read=70785 bytes_retransmit=0 bytes_invalid=0 send_seq=3693 receive_seq=3693 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997196 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124715 bytes_read=3690290 bytes_retransmit=9 bytes_invalid=0 send_seq=16730 receive_seq=16730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997649 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=73968 bytes_read=1539651 bytes_retransmit=9 bytes_invalid=0 send_seq=9569 receive_seq=9569 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22597 bytes_read=906033 bytes_retransmit=9 bytes_invalid=0 send_seq=3707 receive_seq=3707 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23083 bytes_read=69421 bytes_retransmit=9 bytes_invalid=0 send_seq=3694 receive_seq=3694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999449 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77175 bytes_read=1495175 bytes_retransmit=0 bytes_invalid=0 send_seq=8253 receive_seq=8253 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998722 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=45.4 th1: temp=44.5 th2: temp=49.4 th3: temp=47.5 sysload=0.08 cputime=272.529 memavail=7396440 print_time=3582.976 buffer_time=2.328 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 37 Hz
Stats 3559.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20448298 bytes_read=2729539 bytes_retransmit=9 bytes_invalid=0 send_seq=363407 receive_seq=363407 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=0 freq=400015699 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22336 bytes_read=70801 bytes_retransmit=0 bytes_invalid=0 send_seq=3694 receive_seq=3694 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997211 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124791 bytes_read=3693377 bytes_retransmit=9 bytes_invalid=0 send_seq=16741 receive_seq=16741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997673 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=73974 bytes_read=1539779 bytes_retransmit=9 bytes_invalid=0 send_seq=9570 receive_seq=9570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997517 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22603 bytes_read=906307 bytes_retransmit=9 bytes_invalid=0 send_seq=3708 receive_seq=3708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23089 bytes_read=69437 bytes_retransmit=9 bytes_invalid=0 send_seq=3695 receive_seq=3695 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77181 bytes_read=1495531 bytes_retransmit=0 bytes_invalid=0 send_seq=8254 receive_seq=8254 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998701 coil_temp=17.5 refs=0 mcu_temp=20.69 supply_voltage=3.012 th0: temp=45.9 th1: temp=44.1 th2: temp=49.2 th3: temp=47.4 sysload=0.08 cputime=272.608 memavail=7396460 print_time=3583.852 buffer_time=2.204 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 38 Hz
Stats 3560.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20450703 bytes_read=2730164 bytes_retransmit=9 bytes_invalid=0 send_seq=363464 receive_seq=363464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015685 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22342 bytes_read=70817 bytes_retransmit=0 bytes_invalid=0 send_seq=3695 receive_seq=3695 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997212 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124867 bytes_read=3696435 bytes_retransmit=9 bytes_invalid=0 send_seq=16752 receive_seq=16752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997645 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=73980 bytes_read=1539879 bytes_retransmit=9 bytes_invalid=0 send_seq=9571 receive_seq=9571 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22609 bytes_read=906525 bytes_retransmit=9 bytes_invalid=0 send_seq=3709 receive_seq=3709 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23095 bytes_read=69453 bytes_retransmit=9 bytes_invalid=0 send_seq=3696 receive_seq=3696 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77187 bytes_read=1495887 bytes_retransmit=0 bytes_invalid=0 send_seq=8255 receive_seq=8255 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998676 coil_temp=17.5 refs=0 mcu_temp=20.68 supply_voltage=3.012 th0: temp=45.4 th1: temp=44.5 th2: temp=49.3 th3: temp=47.4 sysload=0.08 cputime=272.687 memavail=7396460 print_time=3584.767 buffer_time=2.118 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 39 Hz
Stats 3561.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20452596 bytes_read=2730719 bytes_retransmit=9 bytes_invalid=0 send_seq=363513 receive_seq=363513 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015675 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22348 bytes_read=70833 bytes_retransmit=0 bytes_invalid=0 send_seq=3696 receive_seq=3696 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997237 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124943 bytes_read=3699567 bytes_retransmit=9 bytes_invalid=0 send_seq=16763 receive_seq=16763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997666 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=73986 bytes_read=1539993 bytes_retransmit=9 bytes_invalid=0 send_seq=9572 receive_seq=9572 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997537 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22615 bytes_read=906754 bytes_retransmit=9 bytes_invalid=0 send_seq=3710 receive_seq=3710 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23101 bytes_read=69469 bytes_retransmit=9 bytes_invalid=0 send_seq=3697 receive_seq=3697 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77193 bytes_read=1496243 bytes_retransmit=0 bytes_invalid=0 send_seq=8256 receive_seq=8256 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998681 coil_temp=17.5 refs=0 mcu_temp=20.67 supply_voltage=3.012 th0: temp=45.7 th1: temp=44.4 th2: temp=49.4 th3: temp=47.5 sysload=0.08 cputime=272.769 memavail=7396740 print_time=3585.654 buffer_time=2.004 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 40 Hz
Stats 3562.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20455407 bytes_read=2731363 bytes_retransmit=9 bytes_invalid=0 send_seq=363577 receive_seq=363577 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=47 upcoming_bytes=0 freq=400015668 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22354 bytes_read=70862 bytes_retransmit=0 bytes_invalid=0 send_seq=3697 receive_seq=3697 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997257 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125019 bytes_read=3702654 bytes_retransmit=9 bytes_invalid=0 send_seq=16774 receive_seq=16774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997745 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=73992 bytes_read=1540121 bytes_retransmit=9 bytes_invalid=0 send_seq=9573 receive_seq=9573 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997576 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22621 bytes_read=907063 bytes_retransmit=9 bytes_invalid=0 send_seq=3711 receive_seq=3711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23107 bytes_read=69496 bytes_retransmit=9 bytes_invalid=0 send_seq=3698 receive_seq=3698 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77199 bytes_read=1496599 bytes_retransmit=0 bytes_invalid=0 send_seq=8257 receive_seq=8257 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998681 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=45.9 th1: temp=44.3 th2: temp=49.5 th3: temp=47.3 sysload=0.08 cputime=272.856 memavail=7396740 print_time=3586.870 buffer_time=2.220 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 41 Hz
Stats 3563.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20457987 bytes_read=2731983 bytes_retransmit=9 bytes_invalid=0 send_seq=363636 receive_seq=363636 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=22 upcoming_bytes=0 freq=400015661 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22360 bytes_read=70878 bytes_retransmit=0 bytes_invalid=0 send_seq=3698 receive_seq=3698 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997267 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125095 bytes_read=3705710 bytes_retransmit=9 bytes_invalid=0 send_seq=16785 receive_seq=16785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997720 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=73998 bytes_read=1540221 bytes_retransmit=9 bytes_invalid=0 send_seq=9574 receive_seq=9574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997571 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22627 bytes_read=907297 bytes_retransmit=9 bytes_invalid=0 send_seq=3712 receive_seq=3712 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997694 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23113 bytes_read=69512 bytes_retransmit=9 bytes_invalid=0 send_seq=3699 receive_seq=3699 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77205 bytes_read=1496955 bytes_retransmit=0 bytes_invalid=0 send_seq=8258 receive_seq=8258 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998671 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=45.6 th1: temp=44.5 th2: temp=49.4 th3: temp=47.5 sysload=0.15 cputime=272.943 memavail=7390956 print_time=3587.815 buffer_time=2.164 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 42 Hz
Stats 3564.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=20459991 bytes_read=2732536 bytes_retransmit=9 bytes_invalid=0 send_seq=363686 receive_seq=363686 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=400015652 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22366 bytes_read=70894 bytes_retransmit=0 bytes_invalid=0 send_seq=3699 receive_seq=3699 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997278 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125171 bytes_read=3708767 bytes_retransmit=9 bytes_invalid=0 send_seq=16796 receive_seq=16796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997708 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74004 bytes_read=1540321 bytes_retransmit=9 bytes_invalid=0 send_seq=9575 receive_seq=9575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997574 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22633 bytes_read=907531 bytes_retransmit=9 bytes_invalid=0 send_seq=3713 receive_seq=3713 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997690 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23119 bytes_read=69528 bytes_retransmit=9 bytes_invalid=0 send_seq=3700 receive_seq=3700 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77211 bytes_read=1497311 bytes_retransmit=0 bytes_invalid=0 send_seq=8259 receive_seq=8259 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998674 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=45.8 th1: temp=44.5 th2: temp=49.6 th3: temp=47.5 sysload=0.15 cputime=273.024 memavail=7396860 print_time=3588.697 buffer_time=2.045 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 43 Hz
Stats 3565.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20462968 bytes_read=2733205 bytes_retransmit=9 bytes_invalid=0 send_seq=363752 receive_seq=363752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=0 freq=400015646 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22372 bytes_read=70910 bytes_retransmit=0 bytes_invalid=0 send_seq=3700 receive_seq=3700 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997273 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125247 bytes_read=3711853 bytes_retransmit=9 bytes_invalid=0 send_seq=16807 receive_seq=16807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997700 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74010 bytes_read=1540449 bytes_retransmit=9 bytes_invalid=0 send_seq=9576 receive_seq=9576 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997592 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22639 bytes_read=907825 bytes_retransmit=9 bytes_invalid=0 send_seq=3714 receive_seq=3714 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997719 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23125 bytes_read=69544 bytes_retransmit=9 bytes_invalid=0 send_seq=3701 receive_seq=3701 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999453 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77217 bytes_read=1497667 bytes_retransmit=0 bytes_invalid=0 send_seq=8260 receive_seq=8260 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998666 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=45.8 th1: temp=44.4 th2: temp=48.9 th3: temp=47.4 sysload=0.15 cputime=273.110 memavail=7396860 print_time=3589.908 buffer_time=2.256 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 44 Hz
Stats 3566.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20465560 bytes_read=2733825 bytes_retransmit=9 bytes_invalid=0 send_seq=363811 receive_seq=363811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=0 freq=400015671 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22378 bytes_read=70926 bytes_retransmit=0 bytes_invalid=0 send_seq=3701 receive_seq=3701 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997281 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125323 bytes_read=3714926 bytes_retransmit=9 bytes_invalid=0 send_seq=16818 receive_seq=16818 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997706 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74016 bytes_read=1540549 bytes_retransmit=9 bytes_invalid=0 send_seq=9577 receive_seq=9577 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997579 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=22645 bytes_read=908059 bytes_retransmit=9 bytes_invalid=0 send_seq=3715 receive_seq=3715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997703 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23131 bytes_read=69560 bytes_retransmit=9 bytes_invalid=0 send_seq=3702 receive_seq=3702 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77223 bytes_read=1498023 bytes_retransmit=0 bytes_invalid=0 send_seq=8261 receive_seq=8261 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998666 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=45.6 th1: temp=44.4 th2: temp=49.7 th3: temp=47.4 sysload=0.15 cputime=273.189 memavail=7396396 print_time=3590.828 buffer_time=2.174 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 45 Hz
Stats 3567.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20467616 bytes_read=2734390 bytes_retransmit=9 bytes_invalid=0 send_seq=363862 receive_seq=363862 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=0 freq=400015689 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22384 bytes_read=70955 bytes_retransmit=0 bytes_invalid=0 send_seq=3702 receive_seq=3702 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997249 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125399 bytes_read=3717984 bytes_retransmit=9 bytes_invalid=0 send_seq=16829 receive_seq=16829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997646 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74022 bytes_read=1540663 bytes_retransmit=9 bytes_invalid=0 send_seq=9578 receive_seq=9578 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997522 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22651 bytes_read=908308 bytes_retransmit=9 bytes_invalid=0 send_seq=3716 receive_seq=3716 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997679 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23137 bytes_read=69587 bytes_retransmit=9 bytes_invalid=0 send_seq=3703 receive_seq=3703 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77229 bytes_read=1498379 bytes_retransmit=0 bytes_invalid=0 send_seq=8262 receive_seq=8262 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998655 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=45.9 th1: temp=44.1 th2: temp=49.5 th3: temp=47.4 sysload=0.15 cputime=273.270 memavail=7396400 print_time=3591.712 buffer_time=2.058 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 46 Hz
Stats 3568.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20470697 bytes_read=2735049 bytes_retransmit=9 bytes_invalid=0 send_seq=363929 receive_seq=363929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=0 freq=400015685 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22390 bytes_read=70971 bytes_retransmit=0 bytes_invalid=0 send_seq=3703 receive_seq=3703 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997231 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125468 bytes_read=3721045 bytes_retransmit=9 bytes_invalid=0 send_seq=16839 receive_seq=16839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997590 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74028 bytes_read=1540791 bytes_retransmit=9 bytes_invalid=0 send_seq=9579 receive_seq=9579 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22657 bytes_read=908602 bytes_retransmit=9 bytes_invalid=0 send_seq=3717 receive_seq=3717 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23143 bytes_read=69603 bytes_retransmit=9 bytes_invalid=0 send_seq=3704 receive_seq=3704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999433 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77235 bytes_read=1498735 bytes_retransmit=0 bytes_invalid=0 send_seq=8263 receive_seq=8263 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998639 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=45.8 th1: temp=44.2 th2: temp=49.7 th3: temp=47.6 sysload=0.14 cputime=273.357 memavail=7396400 print_time=3592.926 buffer_time=2.272 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 47 Hz
Stats 3569.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20473333 bytes_read=2735679 bytes_retransmit=9 bytes_invalid=0 send_seq=363990 receive_seq=363990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015772 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22396 bytes_read=70987 bytes_retransmit=0 bytes_invalid=0 send_seq=3704 receive_seq=3704 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997233 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125544 bytes_read=3724159 bytes_retransmit=9 bytes_invalid=0 send_seq=16850 receive_seq=16850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997683 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74034 bytes_read=1540891 bytes_retransmit=9 bytes_invalid=0 send_seq=9580 receive_seq=9580 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997515 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22663 bytes_read=908836 bytes_retransmit=9 bytes_invalid=0 send_seq=3718 receive_seq=3718 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23149 bytes_read=69619 bytes_retransmit=9 bytes_invalid=0 send_seq=3705 receive_seq=3705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77241 bytes_read=1499091 bytes_retransmit=0 bytes_invalid=0 send_seq=8264 receive_seq=8264 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998643 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=45.6 th1: temp=44.4 th2: temp=49.5 th3: temp=47.6 sysload=0.14 cputime=273.438 memavail=7396400 print_time=3593.845 buffer_time=2.190 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 48 Hz
Stats 3570.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20475413 bytes_read=2736259 bytes_retransmit=9 bytes_invalid=0 send_seq=364041 receive_seq=364041 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=47 upcoming_bytes=0 freq=400015778 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22402 bytes_read=71003 bytes_retransmit=0 bytes_invalid=0 send_seq=3705 receive_seq=3705 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997102 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125620 bytes_read=3727215 bytes_retransmit=9 bytes_invalid=0 send_seq=16861 receive_seq=16861 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997499 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74040 bytes_read=1540991 bytes_retransmit=9 bytes_invalid=0 send_seq=9581 receive_seq=9581 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997345 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22669 bytes_read=909070 bytes_retransmit=9 bytes_invalid=0 send_seq=3719 receive_seq=3719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997508 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23155 bytes_read=69635 bytes_retransmit=9 bytes_invalid=0 send_seq=3706 receive_seq=3706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999405 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77247 bytes_read=1499447 bytes_retransmit=0 bytes_invalid=0 send_seq=8265 receive_seq=8265 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998550 coil_temp=17.5 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=45.9 th1: temp=44.4 th2: temp=49.5 th3: temp=47.5 sysload=0.14 cputime=273.518 memavail=7396400 print_time=3594.731 buffer_time=2.076 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 49 Hz
Stats 3571.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20478631 bytes_read=2736913 bytes_retransmit=9 bytes_invalid=0 send_seq=364110 receive_seq=364104 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015787 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22408 bytes_read=71019 bytes_retransmit=0 bytes_invalid=0 send_seq=3706 receive_seq=3706 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997093 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125696 bytes_read=3730317 bytes_retransmit=9 bytes_invalid=0 send_seq=16872 receive_seq=16872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997482 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74046 bytes_read=1541119 bytes_retransmit=9 bytes_invalid=0 send_seq=9582 receive_seq=9582 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997342 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22675 bytes_read=909364 bytes_retransmit=9 bytes_invalid=0 send_seq=3720 receive_seq=3720 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997504 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23161 bytes_read=69651 bytes_retransmit=9 bytes_invalid=0 send_seq=3707 receive_seq=3707 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999404 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77253 bytes_read=1499803 bytes_retransmit=0 bytes_invalid=0 send_seq=8266 receive_seq=8266 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998544 coil_temp=17.5 refs=0 mcu_temp=20.64 supply_voltage=3.012 th0: temp=45.8 th1: temp=44.6 th2: temp=49.6 th3: temp=47.5 sysload=0.14 cputime=273.609 memavail=7396400 print_time=3595.951 buffer_time=2.293 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 50 Hz
Stats 3572.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20481336 bytes_read=2737558 bytes_retransmit=9 bytes_invalid=0 send_seq=364171 receive_seq=364171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=400015777 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22414 bytes_read=71048 bytes_retransmit=0 bytes_invalid=0 send_seq=3707 receive_seq=3707 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997121 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125772 bytes_read=3733373 bytes_retransmit=9 bytes_invalid=0 send_seq=16883 receive_seq=16883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997508 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74052 bytes_read=1541233 bytes_retransmit=9 bytes_invalid=0 send_seq=9583 receive_seq=9583 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997372 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22681 bytes_read=909613 bytes_retransmit=9 bytes_invalid=0 send_seq=3721 receive_seq=3721 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997527 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23167 bytes_read=69678 bytes_retransmit=9 bytes_invalid=0 send_seq=3708 receive_seq=3708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999412 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77259 bytes_read=1500159 bytes_retransmit=0 bytes_invalid=0 send_seq=8267 receive_seq=8267 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998566 coil_temp=17.5 refs=0 mcu_temp=20.64 supply_voltage=3.012 th0: temp=45.8 th1: temp=44.3 th2: temp=49.6 th3: temp=47.7 sysload=0.14 cputime=273.691 memavail=7396400 print_time=3596.854 buffer_time=2.195 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 51 Hz
Stats 3573.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20483437 bytes_read=2738123 bytes_retransmit=9 bytes_invalid=0 send_seq=364222 receive_seq=364222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=0 freq=400015782 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22420 bytes_read=71064 bytes_retransmit=0 bytes_invalid=0 send_seq=3708 receive_seq=3708 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997153 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125848 bytes_read=3736430 bytes_retransmit=9 bytes_invalid=0 send_seq=16894 receive_seq=16894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997650 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74058 bytes_read=1541333 bytes_retransmit=9 bytes_invalid=0 send_seq=9584 receive_seq=9584 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997416 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22687 bytes_read=909847 bytes_retransmit=9 bytes_invalid=0 send_seq=3722 receive_seq=3722 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997548 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23173 bytes_read=69694 bytes_retransmit=9 bytes_invalid=0 send_seq=3709 receive_seq=3709 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999418 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77265 bytes_read=1500515 bytes_retransmit=0 bytes_invalid=0 send_seq=8268 receive_seq=8268 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998584 coil_temp=17.5 refs=0 mcu_temp=20.64 supply_voltage=3.012 th0: temp=45.8 th1: temp=44.5 th2: temp=49.5 th3: temp=47.6 sysload=0.13 cputime=273.771 memavail=7396400 print_time=3597.742 buffer_time=2.082 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 52 Hz
Stats 3574.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20486673 bytes_read=2738780 bytes_retransmit=9 bytes_invalid=0 send_seq=364292 receive_seq=364286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=47 upcoming_bytes=0 freq=400015782 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22426 bytes_read=71080 bytes_retransmit=0 bytes_invalid=0 send_seq=3709 receive_seq=3709 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997159 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125924 bytes_read=3739572 bytes_retransmit=9 bytes_invalid=0 send_seq=16905 receive_seq=16905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997731 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74064 bytes_read=1541461 bytes_retransmit=9 bytes_invalid=0 send_seq=9585 receive_seq=9585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997442 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22693 bytes_read=910141 bytes_retransmit=9 bytes_invalid=0 send_seq=3723 receive_seq=3723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997546 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23179 bytes_read=69710 bytes_retransmit=9 bytes_invalid=0 send_seq=3710 receive_seq=3710 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999420 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77271 bytes_read=1500871 bytes_retransmit=0 bytes_invalid=0 send_seq=8269 receive_seq=8269 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998585 coil_temp=17.5 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.0 th1: temp=44.3 th2: temp=49.6 th3: temp=47.6 sysload=0.13 cputime=273.861 memavail=7396436 print_time=3598.954 buffer_time=2.290 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 53 Hz
Stats 3575.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20489431 bytes_read=2739442 bytes_retransmit=9 bytes_invalid=0 send_seq=364354 receive_seq=364354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=47 upcoming_bytes=0 freq=400015804 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22432 bytes_read=71096 bytes_retransmit=0 bytes_invalid=0 send_seq=3710 receive_seq=3710 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997176 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=126000 bytes_read=3742630 bytes_retransmit=9 bytes_invalid=0 send_seq=16916 receive_seq=16916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997688 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74070 bytes_read=1541561 bytes_retransmit=9 bytes_invalid=0 send_seq=9586 receive_seq=9586 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22699 bytes_read=910375 bytes_retransmit=9 bytes_invalid=0 send_seq=3724 receive_seq=3724 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997581 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23185 bytes_read=69726 bytes_retransmit=9 bytes_invalid=0 send_seq=3711 receive_seq=3711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77277 bytes_read=1501227 bytes_retransmit=0 bytes_invalid=0 send_seq=8270 receive_seq=8270 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998598 coil_temp=17.5 refs=0 mcu_temp=20.62 supply_voltage=3.012 th0: temp=46.1 th1: temp=44.3 th2: temp=49.7 th3: temp=47.6 sysload=0.13 cputime=273.944 memavail=7396436 print_time=3599.854 buffer_time=2.189 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 54 Hz
Stats 3576.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20491712 bytes_read=2740027 bytes_retransmit=9 bytes_invalid=0 send_seq=364409 receive_seq=364409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015818 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22438 bytes_read=71112 bytes_retransmit=0 bytes_invalid=0 send_seq=3711 receive_seq=3711 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997151 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=126076 bytes_read=3745707 bytes_retransmit=9 bytes_invalid=0 send_seq=16927 receive_seq=16927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997619 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74076 bytes_read=1541661 bytes_retransmit=9 bytes_invalid=0 send_seq=9587 receive_seq=9587 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997443 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22705 bytes_read=910609 bytes_retransmit=9 bytes_invalid=0 send_seq=3725 receive_seq=3725 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997560 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23191 bytes_read=69742 bytes_retransmit=9 bytes_invalid=0 send_seq=3712 receive_seq=3712 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999425 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77283 bytes_read=1501583 bytes_retransmit=0 bytes_invalid=0 send_seq=8271 receive_seq=8271 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998573 coil_temp=17.5 refs=0 mcu_temp=20.61 supply_voltage=3.012 th0: temp=45.8 th1: temp=44.8 th2: temp=49.7 th3: temp=47.6 sysload=0.13 cputime=274.027 memavail=7396448 print_time=3600.766 buffer_time=2.101 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 55 Hz
Stats 3577.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20494559 bytes_read=2740671 bytes_retransmit=9 bytes_invalid=0 send_seq=364470 receive_seq=364470 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015820 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22444 bytes_read=71141 bytes_retransmit=0 bytes_invalid=0 send_seq=3712 receive_seq=3712 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997148 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=126152 bytes_read=3748792 bytes_retransmit=9 bytes_invalid=0 send_seq=16938 receive_seq=16938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997578 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74082 bytes_read=1541803 bytes_retransmit=9 bytes_invalid=0 send_seq=9588 receive_seq=9588 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997410 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22711 bytes_read=910918 bytes_retransmit=9 bytes_invalid=0 send_seq=3726 receive_seq=3726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997544 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23197 bytes_read=69769 bytes_retransmit=9 bytes_invalid=0 send_seq=3713 receive_seq=3713 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999425 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77289 bytes_read=1501939 bytes_retransmit=0 bytes_invalid=0 send_seq=8272 receive_seq=8272 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998569 coil_temp=17.4 refs=0 mcu_temp=20.60 supply_voltage=3.012 th0: temp=46.1 th1: temp=44.3 th2: temp=49.7 th3: temp=47.7 sysload=0.13 cputime=274.111 memavail=7396448 print_time=3601.668 buffer_time=2.002 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 56 Hz
Stats 3578.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20497866 bytes_read=2741341 bytes_retransmit=9 bytes_invalid=0 send_seq=364542 receive_seq=364542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=0 freq=400015815 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22450 bytes_read=71157 bytes_retransmit=0 bytes_invalid=0 send_seq=3713 receive_seq=3713 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997149 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=126228 bytes_read=3751850 bytes_retransmit=9 bytes_invalid=0 send_seq=16949 receive_seq=16949 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997621 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74088 bytes_read=1541903 bytes_retransmit=9 bytes_invalid=0 send_seq=9589 receive_seq=9589 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997414 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22717 bytes_read=911152 bytes_retransmit=9 bytes_invalid=0 send_seq=3727 receive_seq=3727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997549 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23203 bytes_read=69785 bytes_retransmit=9 bytes_invalid=0 send_seq=3714 receive_seq=3714 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999424 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77295 bytes_read=1502295 bytes_retransmit=0 bytes_invalid=0 send_seq=8273 receive_seq=8273 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998627 coil_temp=17.4 refs=0 mcu_temp=20.60 supply_voltage=3.012 th0: temp=45.7 th1: temp=44.4 th2: temp=49.7 th3: temp=47.6 sysload=0.20 cputime=274.202 memavail=7396448 print_time=3602.871 buffer_time=2.205 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 57 Hz
Stats 3579.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20500203 bytes_read=2741931 bytes_retransmit=9 bytes_invalid=0 send_seq=364598 receive_seq=364598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=0 freq=400015803 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22456 bytes_read=71173 bytes_retransmit=0 bytes_invalid=0 send_seq=3714 receive_seq=3714 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997185 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=126304 bytes_read=3754907 bytes_retransmit=9 bytes_invalid=0 send_seq=16960 receive_seq=16960 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997699 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74094 bytes_read=1542003 bytes_retransmit=9 bytes_invalid=0 send_seq=9590 receive_seq=9590 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997458 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22723 bytes_read=911386 bytes_retransmit=9 bytes_invalid=0 send_seq=3728 receive_seq=3728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997582 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23209 bytes_read=69801 bytes_retransmit=9 bytes_invalid=0 send_seq=3715 receive_seq=3715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999430 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77301 bytes_read=1502651 bytes_retransmit=0 bytes_invalid=0 send_seq=8274 receive_seq=8274 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998658 coil_temp=17.4 refs=0 mcu_temp=20.60 supply_voltage=3.012 th0: temp=45.7 th1: temp=44.5 th2: temp=49.7 th3: temp=47.6 sysload=0.20 cputime=274.286 memavail=7396448 print_time=3603.792 buffer_time=2.125 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 58 Hz
Stats 3580.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20503125 bytes_read=2742605 bytes_retransmit=9 bytes_invalid=0 send_seq=364662 receive_seq=364662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015787 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22462 bytes_read=71189 bytes_retransmit=0 bytes_invalid=0 send_seq=3715 receive_seq=3715 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997215 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=126380 bytes_read=3757994 bytes_retransmit=9 bytes_invalid=0 send_seq=16971 receive_seq=16971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997795 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74100 bytes_read=1542131 bytes_retransmit=9 bytes_invalid=0 send_seq=9591 receive_seq=9591 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22729 bytes_read=911680 bytes_retransmit=9 bytes_invalid=0 send_seq=3729 receive_seq=3729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997600 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23215 bytes_read=69817 bytes_retransmit=9 bytes_invalid=0 send_seq=3716 receive_seq=3716 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999433 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77307 bytes_read=1503007 bytes_retransmit=0 bytes_invalid=0 send_seq=8275 receive_seq=8275 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998656 coil_temp=17.4 refs=0 mcu_temp=20.60 supply_voltage=3.012 th0: temp=46.0 th1: temp=44.5 th2: temp=49.7 th3: temp=47.5 sysload=0.20 cputime=274.374 memavail=7394432 print_time=3604.681 buffer_time=2.014 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 59 Hz
Stats 3581.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20506522 bytes_read=2743280 bytes_retransmit=9 bytes_invalid=0 send_seq=364735 receive_seq=364735 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=0 freq=400015792 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22468 bytes_read=71205 bytes_retransmit=0 bytes_invalid=0 send_seq=3716 receive_seq=3716 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997249 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=126456 bytes_read=3761125 bytes_retransmit=9 bytes_invalid=0 send_seq=16982 receive_seq=16982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997781 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74106 bytes_read=1542231 bytes_retransmit=9 bytes_invalid=0 send_seq=9592 receive_seq=9592 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22735 bytes_read=911914 bytes_retransmit=9 bytes_invalid=0 send_seq=3730 receive_seq=3730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23221 bytes_read=69833 bytes_retransmit=9 bytes_invalid=0 send_seq=3717 receive_seq=3717 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77313 bytes_read=1503359 bytes_retransmit=0 bytes_invalid=0 send_seq=8276 receive_seq=8276 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998674 coil_temp=17.4 refs=0 mcu_temp=20.60 supply_voltage=3.012 th0: temp=45.9 th1: temp=44.4 th2: temp=49.9 th3: temp=47.7 sysload=0.20 cputime=274.471 memavail=7396684 print_time=3605.882 buffer_time=2.214 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 60 Hz
Stats 3582.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20508954 bytes_read=2743875 bytes_retransmit=9 bytes_invalid=0 send_seq=364792 receive_seq=364792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=400015776 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22474 bytes_read=71234 bytes_retransmit=0 bytes_invalid=0 send_seq=3717 receive_seq=3717 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997251 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=126532 bytes_read=3764183 bytes_retransmit=9 bytes_invalid=0 send_seq=16993 receive_seq=16993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997716 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74112 bytes_read=1542345 bytes_retransmit=9 bytes_invalid=0 send_seq=9593 receive_seq=9593 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22741 bytes_read=912163 bytes_retransmit=9 bytes_invalid=0 send_seq=3731 receive_seq=3731 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23227 bytes_read=69860 bytes_retransmit=9 bytes_invalid=0 send_seq=3718 receive_seq=3718 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77319 bytes_read=1503704 bytes_retransmit=0 bytes_invalid=0 send_seq=8277 receive_seq=8277 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998654 coil_temp=17.4 refs=0 mcu_temp=20.61 supply_voltage=3.012 th0: temp=46.1 th1: temp=44.3 th2: temp=49.9 th3: temp=47.5 sysload=0.20 cputime=274.556 memavail=7396808 print_time=3606.811 buffer_time=2.143 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 61 Hz
Stats 3583.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20511836 bytes_read=2744534 bytes_retransmit=9 bytes_invalid=0 send_seq=364856 receive_seq=364856 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=0 freq=400015762 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22480 bytes_read=71250 bytes_retransmit=0 bytes_invalid=0 send_seq=3718 receive_seq=3718 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997278 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=126608 bytes_read=3767269 bytes_retransmit=9 bytes_invalid=0 send_seq=17004 receive_seq=17004 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997714 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74118 bytes_read=1542473 bytes_retransmit=9 bytes_invalid=0 send_seq=9594 receive_seq=9594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22747 bytes_read=912457 bytes_retransmit=9 bytes_invalid=0 send_seq=3732 receive_seq=3732 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23233 bytes_read=69876 bytes_retransmit=9 bytes_invalid=0 send_seq=3719 receive_seq=3719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77325 bytes_read=1504049 bytes_retransmit=0 bytes_invalid=0 send_seq=8278 receive_seq=8278 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998663 coil_temp=17.4 refs=0 mcu_temp=20.62 supply_voltage=3.012 th0: temp=45.9 th1: temp=44.5 th2: temp=50.0 th3: temp=47.7 sysload=0.18 cputime=274.641 memavail=7396808 print_time=3607.701 buffer_time=2.033 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 62 Hz
Stats 3584.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20515409 bytes_read=2745224 bytes_retransmit=9 bytes_invalid=0 send_seq=364932 receive_seq=364932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015785 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22486 bytes_read=71266 bytes_retransmit=0 bytes_invalid=0 send_seq=3719 receive_seq=3719 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997296 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=126684 bytes_read=3770327 bytes_retransmit=9 bytes_invalid=0 send_seq=17015 receive_seq=17015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997711 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74124 bytes_read=1542573 bytes_retransmit=9 bytes_invalid=0 send_seq=9595 receive_seq=9595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997569 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22753 bytes_read=912691 bytes_retransmit=9 bytes_invalid=0 send_seq=3733 receive_seq=3733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23239 bytes_read=69892 bytes_retransmit=9 bytes_invalid=0 send_seq=3720 receive_seq=3720 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77331 bytes_read=1504394 bytes_retransmit=0 bytes_invalid=0 send_seq=8279 receive_seq=8279 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998671 coil_temp=17.4 refs=0 mcu_temp=20.62 supply_voltage=3.012 th0: temp=46.0 th1: temp=44.4 th2: temp=49.8 th3: temp=47.9 sysload=0.18 cputime=274.734 memavail=7396808 print_time=3608.900 buffer_time=2.231 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 63 Hz
Stats 3585.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20517954 bytes_read=2745843 bytes_retransmit=9 bytes_invalid=0 send_seq=364991 receive_seq=364991 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=26 upcoming_bytes=0 freq=400015780 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22492 bytes_read=71282 bytes_retransmit=0 bytes_invalid=0 send_seq=3720 receive_seq=3720 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997237 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=126760 bytes_read=3773384 bytes_retransmit=9 bytes_invalid=0 send_seq=17026 receive_seq=17026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997631 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74130 bytes_read=1542673 bytes_retransmit=9 bytes_invalid=0 send_seq=9596 receive_seq=9596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22759 bytes_read=912925 bytes_retransmit=9 bytes_invalid=0 send_seq=3734 receive_seq=3734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997626 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23245 bytes_read=69908 bytes_retransmit=9 bytes_invalid=0 send_seq=3721 receive_seq=3721 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77337 bytes_read=1504739 bytes_retransmit=0 bytes_invalid=0 send_seq=8280 receive_seq=8280 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998650 coil_temp=17.4 refs=0 mcu_temp=20.62 supply_voltage=3.012 th0: temp=45.9 th1: temp=44.2 th2: temp=49.8 th3: temp=47.6 sysload=0.18 cputime=274.819 memavail=7396808 print_time=3609.828 buffer_time=2.159 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 64 Hz
Stats 3586.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20520881 bytes_read=2746504 bytes_retransmit=9 bytes_invalid=0 send_seq=365056 receive_seq=365056 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=23 upcoming_bytes=0 freq=400015780 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22498 bytes_read=71298 bytes_retransmit=0 bytes_invalid=0 send_seq=3721 receive_seq=3721 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997248 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=126829 bytes_read=3776462 bytes_retransmit=9 bytes_invalid=0 send_seq=17036 receive_seq=17036 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997739 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74136 bytes_read=1542801 bytes_retransmit=9 bytes_invalid=0 send_seq=9597 receive_seq=9597 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22765 bytes_read=913219 bytes_retransmit=9 bytes_invalid=0 send_seq=3735 receive_seq=3735 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23251 bytes_read=69924 bytes_retransmit=9 bytes_invalid=0 send_seq=3722 receive_seq=3722 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77343 bytes_read=1505084 bytes_retransmit=0 bytes_invalid=0 send_seq=8281 receive_seq=8281 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998645 coil_temp=17.4 refs=0 mcu_temp=20.62 supply_voltage=3.012 th0: temp=45.8 th1: temp=44.4 th2: temp=49.9 th3: temp=47.8 sysload=0.18 cputime=274.904 memavail=7396352 print_time=3610.700 buffer_time=2.030 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 65 Hz
Stats 3587.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20524456 bytes_read=2747189 bytes_retransmit=9 bytes_invalid=0 send_seq=365131 receive_seq=365131 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=400015788 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22504 bytes_read=71314 bytes_retransmit=0 bytes_invalid=0 send_seq=3722 receive_seq=3722 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997245 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=126905 bytes_read=3779520 bytes_retransmit=9 bytes_invalid=0 send_seq=17047 receive_seq=17047 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997820 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74142 bytes_read=1542915 bytes_retransmit=9 bytes_invalid=0 send_seq=9598 receive_seq=9598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22771 bytes_read=913468 bytes_retransmit=9 bytes_invalid=0 send_seq=3736 receive_seq=3736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23257 bytes_read=69951 bytes_retransmit=9 bytes_invalid=0 send_seq=3723 receive_seq=3723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77349 bytes_read=1505429 bytes_retransmit=0 bytes_invalid=0 send_seq=8282 receive_seq=8282 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998661 coil_temp=17.4 refs=0 mcu_temp=20.61 supply_voltage=3.012 th0: temp=46.1 th1: temp=44.5 th2: temp=49.9 th3: temp=47.8 sysload=0.18 cputime=274.997 memavail=7396352 print_time=3611.901 buffer_time=2.230 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 66 Hz
Stats 3588.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20527107 bytes_read=2747804 bytes_retransmit=9 bytes_invalid=0 send_seq=365192 receive_seq=365192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015790 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22510 bytes_read=71343 bytes_retransmit=0 bytes_invalid=0 send_seq=3723 receive_seq=3723 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997227 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=126981 bytes_read=3782577 bytes_retransmit=9 bytes_invalid=0 send_seq=17058 receive_seq=17058 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997881 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74148 bytes_read=1543015 bytes_retransmit=9 bytes_invalid=0 send_seq=9599 receive_seq=9599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22777 bytes_read=913702 bytes_retransmit=9 bytes_invalid=0 send_seq=3737 receive_seq=3737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23263 bytes_read=69967 bytes_retransmit=9 bytes_invalid=0 send_seq=3724 receive_seq=3724 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77355 bytes_read=1505774 bytes_retransmit=0 bytes_invalid=0 send_seq=8283 receive_seq=8283 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998652 coil_temp=17.4 refs=0 mcu_temp=20.60 supply_voltage=3.012 th0: temp=46.0 th1: temp=44.4 th2: temp=49.8 th3: temp=47.9 sysload=0.17 cputime=275.082 memavail=7396352 print_time=3612.834 buffer_time=2.162 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 67 Hz
Stats 3589.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20530104 bytes_read=2748478 bytes_retransmit=9 bytes_invalid=0 send_seq=365259 receive_seq=365259 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015782 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22516 bytes_read=71359 bytes_retransmit=0 bytes_invalid=0 send_seq=3724 receive_seq=3724 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997230 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127057 bytes_read=3785719 bytes_retransmit=9 bytes_invalid=0 send_seq=17069 receive_seq=17069 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997893 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74154 bytes_read=1543143 bytes_retransmit=9 bytes_invalid=0 send_seq=9600 receive_seq=9600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997493 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22783 bytes_read=913996 bytes_retransmit=9 bytes_invalid=0 send_seq=3738 receive_seq=3738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23269 bytes_read=69983 bytes_retransmit=9 bytes_invalid=0 send_seq=3725 receive_seq=3725 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77361 bytes_read=1506119 bytes_retransmit=0 bytes_invalid=0 send_seq=8284 receive_seq=8284 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998639 coil_temp=17.4 refs=0 mcu_temp=20.60 supply_voltage=3.012 th0: temp=45.8 th1: temp=44.5 th2: temp=50.0 th3: temp=47.8 sysload=0.17 cputime=275.167 memavail=7396352 print_time=3613.717 buffer_time=2.045 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 68 Hz
Stats 3590.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20533846 bytes_read=2749194 bytes_retransmit=9 bytes_invalid=0 send_seq=365337 receive_seq=365337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015783 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22522 bytes_read=71375 bytes_retransmit=0 bytes_invalid=0 send_seq=3725 receive_seq=3725 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997230 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127133 bytes_read=3788777 bytes_retransmit=9 bytes_invalid=0 send_seq=17080 receive_seq=17080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997857 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74160 bytes_read=1543243 bytes_retransmit=9 bytes_invalid=0 send_seq=9601 receive_seq=9601 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22789 bytes_read=914230 bytes_retransmit=9 bytes_invalid=0 send_seq=3739 receive_seq=3739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23275 bytes_read=69999 bytes_retransmit=9 bytes_invalid=0 send_seq=3726 receive_seq=3726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77367 bytes_read=1506475 bytes_retransmit=0 bytes_invalid=0 send_seq=8285 receive_seq=8285 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998640 coil_temp=17.4 refs=0 mcu_temp=20.60 supply_voltage=3.012 th0: temp=46.0 th1: temp=44.6 th2: temp=49.9 th3: temp=47.9 sysload=0.17 cputime=275.263 memavail=7396352 print_time=3614.913 buffer_time=2.240 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 69 Hz
Stats 3591.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20536596 bytes_read=2749814 bytes_retransmit=9 bytes_invalid=0 send_seq=365399 receive_seq=365399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=0 freq=400015784 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22528 bytes_read=71391 bytes_retransmit=0 bytes_invalid=0 send_seq=3726 receive_seq=3726 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997229 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127209 bytes_read=3791850 bytes_retransmit=9 bytes_invalid=0 send_seq=17091 receive_seq=17091 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997774 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74166 bytes_read=1543343 bytes_retransmit=9 bytes_invalid=0 send_seq=9602 receive_seq=9602 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22795 bytes_read=914464 bytes_retransmit=9 bytes_invalid=0 send_seq=3740 receive_seq=3740 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997649 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23281 bytes_read=70015 bytes_retransmit=9 bytes_invalid=0 send_seq=3727 receive_seq=3727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77373 bytes_read=1506831 bytes_retransmit=0 bytes_invalid=0 send_seq=8286 receive_seq=8286 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998636 coil_temp=17.4 refs=0 mcu_temp=20.62 supply_voltage=3.012 th0: temp=46.1 th1: temp=44.9 th2: temp=49.8 th3: temp=47.9 sysload=0.17 cputime=275.355 memavail=7396352 print_time=3615.851 buffer_time=2.177 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 70 Hz
Stats 3592.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20539614 bytes_read=2750483 bytes_retransmit=9 bytes_invalid=0 send_seq=365465 receive_seq=365465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=400015805 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22534 bytes_read=71407 bytes_retransmit=0 bytes_invalid=0 send_seq=3727 receive_seq=3727 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997238 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127285 bytes_read=3794936 bytes_retransmit=9 bytes_invalid=0 send_seq=17102 receive_seq=17102 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997727 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74172 bytes_read=1543485 bytes_retransmit=9 bytes_invalid=0 send_seq=9603 receive_seq=9603 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997515 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22801 bytes_read=914773 bytes_retransmit=9 bytes_invalid=0 send_seq=3741 receive_seq=3741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23287 bytes_read=70042 bytes_retransmit=9 bytes_invalid=0 send_seq=3728 receive_seq=3728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77379 bytes_read=1507187 bytes_retransmit=0 bytes_invalid=0 send_seq=8287 receive_seq=8287 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998628 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=45.7 th1: temp=45.0 th2: temp=49.9 th3: temp=48.0 sysload=0.17 cputime=275.442 memavail=7396352 print_time=3616.723 buffer_time=2.048 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 71 Hz
Stats 3593.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20543359 bytes_read=2751183 bytes_retransmit=9 bytes_invalid=0 send_seq=365543 receive_seq=365543 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=0 freq=400015817 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22540 bytes_read=71436 bytes_retransmit=0 bytes_invalid=0 send_seq=3728 receive_seq=3728 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997220 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127361 bytes_read=3797992 bytes_retransmit=9 bytes_invalid=0 send_seq=17113 receive_seq=17113 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997654 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74178 bytes_read=1543585 bytes_retransmit=9 bytes_invalid=0 send_seq=9604 receive_seq=9604 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22807 bytes_read=915007 bytes_retransmit=9 bytes_invalid=0 send_seq=3742 receive_seq=3742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997605 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23293 bytes_read=70058 bytes_retransmit=9 bytes_invalid=0 send_seq=3729 receive_seq=3729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999429 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77385 bytes_read=1507543 bytes_retransmit=0 bytes_invalid=0 send_seq=8288 receive_seq=8288 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999917 adj=31998604 coil_temp=17.4 refs=0 mcu_temp=20.64 supply_voltage=3.012 th0: temp=46.0 th1: temp=44.5 th2: temp=49.8 th3: temp=48.0 sysload=0.15 cputime=275.537 memavail=7396352 print_time=3617.928 buffer_time=2.253 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 72 Hz
Stats 3594.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20546331 bytes_read=2751818 bytes_retransmit=9 bytes_invalid=0 send_seq=365608 receive_seq=365608 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015828 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22546 bytes_read=71452 bytes_retransmit=0 bytes_invalid=0 send_seq=3729 receive_seq=3729 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997221 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127437 bytes_read=3801050 bytes_retransmit=9 bytes_invalid=0 send_seq=17124 receive_seq=17124 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997717 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74184 bytes_read=1543685 bytes_retransmit=9 bytes_invalid=0 send_seq=9605 receive_seq=9605 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997460 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22813 bytes_read=915241 bytes_retransmit=9 bytes_invalid=0 send_seq=3743 receive_seq=3743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997595 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23299 bytes_read=70074 bytes_retransmit=9 bytes_invalid=0 send_seq=3730 receive_seq=3730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999431 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77391 bytes_read=1507899 bytes_retransmit=0 bytes_invalid=0 send_seq=8289 receive_seq=8289 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998601 coil_temp=17.4 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.2 th1: temp=44.6 th2: temp=50.0 th3: temp=47.8 sysload=0.15 cputime=275.625 memavail=7396388 print_time=3618.868 buffer_time=2.192 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 73 Hz
Stats 3595.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20549335 bytes_read=2752503 bytes_retransmit=9 bytes_invalid=0 send_seq=365674 receive_seq=365674 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=0 freq=400015828 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22552 bytes_read=71468 bytes_retransmit=0 bytes_invalid=0 send_seq=3730 receive_seq=3730 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997202 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127513 bytes_read=3804135 bytes_retransmit=9 bytes_invalid=0 send_seq=17135 receive_seq=17135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997645 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74190 bytes_read=1543813 bytes_retransmit=9 bytes_invalid=0 send_seq=9606 receive_seq=9606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997455 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22819 bytes_read=915535 bytes_retransmit=9 bytes_invalid=0 send_seq=3744 receive_seq=3744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997588 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23305 bytes_read=70090 bytes_retransmit=9 bytes_invalid=0 send_seq=3731 receive_seq=3731 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999427 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77397 bytes_read=1508255 bytes_retransmit=0 bytes_invalid=0 send_seq=8290 receive_seq=8290 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998618 coil_temp=17.4 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.0 th1: temp=44.6 th2: temp=49.7 th3: temp=48.0 sysload=0.15 cputime=275.715 memavail=7396388 print_time=3619.741 buffer_time=2.064 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 74 Hz
Stats 3596.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20552398 bytes_read=2753144 bytes_retransmit=9 bytes_invalid=0 send_seq=365741 receive_seq=365741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015834 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22558 bytes_read=71484 bytes_retransmit=0 bytes_invalid=0 send_seq=3731 receive_seq=3731 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997205 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127589 bytes_read=3807267 bytes_retransmit=9 bytes_invalid=0 send_seq=17146 receive_seq=17146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997615 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74196 bytes_read=1543913 bytes_retransmit=9 bytes_invalid=0 send_seq=9607 receive_seq=9607 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997467 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22825 bytes_read=915769 bytes_retransmit=9 bytes_invalid=0 send_seq=3745 receive_seq=3745 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23311 bytes_read=70106 bytes_retransmit=9 bytes_invalid=0 send_seq=3732 receive_seq=3732 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999428 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77403 bytes_read=1508611 bytes_retransmit=0 bytes_invalid=0 send_seq=8291 receive_seq=8291 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998647 coil_temp=17.4 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.2 th1: temp=44.6 th2: temp=50.0 th3: temp=47.9 sysload=0.15 cputime=275.805 memavail=7396400 print_time=3620.678 buffer_time=2.001 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 75 Hz
Stats 3597.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20556231 bytes_read=2753853 bytes_retransmit=9 bytes_invalid=0 send_seq=365821 receive_seq=365821 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=0 freq=400015827 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22564 bytes_read=71500 bytes_retransmit=0 bytes_invalid=0 send_seq=3732 receive_seq=3732 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997193 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127665 bytes_read=3810324 bytes_retransmit=9 bytes_invalid=0 send_seq=17157 receive_seq=17157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997569 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=74202 bytes_read=1544027 bytes_retransmit=9 bytes_invalid=0 send_seq=9608 receive_seq=9608 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997457 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22831 bytes_read=916018 bytes_retransmit=9 bytes_invalid=0 send_seq=3746 receive_seq=3746 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23317 bytes_read=70133 bytes_retransmit=9 bytes_invalid=0 send_seq=3733 receive_seq=3733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999427 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77409 bytes_read=1508967 bytes_retransmit=0 bytes_invalid=0 send_seq=8292 receive_seq=8292 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998639 coil_temp=17.4 refs=0 mcu_temp=20.65 supply_voltage=3.012 th0: temp=46.2 th1: temp=45.0 th2: temp=49.6 th3: temp=48.1 sysload=0.15 cputime=275.902 memavail=7396400 print_time=3621.873 buffer_time=2.196 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 76 Hz
Stats 3598.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20559267 bytes_read=2754522 bytes_retransmit=9 bytes_invalid=0 send_seq=365887 receive_seq=365887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=0 freq=400015828 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=22570 bytes_read=71529 bytes_retransmit=0 bytes_invalid=0 send_seq=3733 receive_seq=3733 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997207 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127741 bytes_read=3813409 bytes_retransmit=9 bytes_invalid=0 send_seq=17168 receive_seq=17168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997576 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=74208 bytes_read=1544155 bytes_retransmit=9 bytes_invalid=0 send_seq=9609 receive_seq=9609 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22837 bytes_read=916312 bytes_retransmit=9 bytes_invalid=0 send_seq=3747 receive_seq=3747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23323 bytes_read=70149 bytes_retransmit=9 bytes_invalid=0 send_seq=3734 receive_seq=3734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999433 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77415 bytes_read=1509323 bytes_retransmit=0 bytes_invalid=0 send_seq=8293 receive_seq=8293 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998656 coil_temp=17.4 refs=0 mcu_temp=20.64 supply_voltage=3.012 th0: temp=46.3 th1: temp=44.3 th2: temp=50.0 th3: temp=48.0 sysload=0.14 cputime=276.001 memavail=7397804 print_time=3622.748 buffer_time=2.071 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 77 Hz
Stats 3599.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20562364 bytes_read=2755167 bytes_retransmit=9 bytes_invalid=0 send_seq=365954 receive_seq=365954 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015834 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=22576 bytes_read=71545 bytes_retransmit=0 bytes_invalid=0 send_seq=3734 receive_seq=3734 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997231 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127817 bytes_read=3816467 bytes_retransmit=9 bytes_invalid=0 send_seq=17179 receive_seq=17179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997546 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=74214 bytes_read=1544255 bytes_retransmit=9 bytes_invalid=0 send_seq=9610 receive_seq=9610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997477 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22843 bytes_read=916546 bytes_retransmit=9 bytes_invalid=0 send_seq=3748 receive_seq=3748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997632 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23329 bytes_read=70165 bytes_retransmit=9 bytes_invalid=0 send_seq=3735 receive_seq=3735 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77421 bytes_read=1509679 bytes_retransmit=0 bytes_invalid=0 send_seq=8294 receive_seq=8294 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998644 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=45.5 th1: temp=44.6 th2: temp=50.0 th3: temp=47.9 sysload=0.14 cputime=276.090 memavail=7397556 print_time=3623.681 buffer_time=2.004 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 78 Hz
Stats 3600.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20566437 bytes_read=2755908 bytes_retransmit=9 bytes_invalid=0 send_seq=366037 receive_seq=366037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=0 freq=400015834 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=22582 bytes_read=71561 bytes_retransmit=0 bytes_invalid=0 send_seq=3735 receive_seq=3735 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997220 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127893 bytes_read=3819519 bytes_retransmit=9 bytes_invalid=0 send_seq=17190 receive_seq=17190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997514 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=74220 bytes_read=1544353 bytes_retransmit=9 bytes_invalid=0 send_seq=9611 receive_seq=9611 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22849 bytes_read=916780 bytes_retransmit=9 bytes_invalid=0 send_seq=3749 receive_seq=3749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997618 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23335 bytes_read=70181 bytes_retransmit=9 bytes_invalid=0 send_seq=3736 receive_seq=3736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77427 bytes_read=1510035 bytes_retransmit=0 bytes_invalid=0 send_seq=8295 receive_seq=8295 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998643 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.2 th1: temp=44.6 th2: temp=49.9 th3: temp=47.9 sysload=0.14 cputime=276.187 memavail=7397556 print_time=3624.888 buffer_time=2.210 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 79 Hz
Stats 3601.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20569412 bytes_read=2756577 bytes_retransmit=9 bytes_invalid=0 send_seq=366103 receive_seq=366103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=0 freq=400015837 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=22588 bytes_read=71577 bytes_retransmit=0 bytes_invalid=0 send_seq=3736 receive_seq=3736 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997214 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127962 bytes_read=3822581 bytes_retransmit=9 bytes_invalid=0 send_seq=17200 receive_seq=17200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997531 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=74226 bytes_read=1544471 bytes_retransmit=9 bytes_invalid=0 send_seq=9612 receive_seq=9612 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997485 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=22855 bytes_read=917074 bytes_retransmit=9 bytes_invalid=0 send_seq=3750 receive_seq=3750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997618 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23341 bytes_read=70197 bytes_retransmit=9 bytes_invalid=0 send_seq=3737 receive_seq=3737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999436 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77433 bytes_read=1510391 bytes_retransmit=0 bytes_invalid=0 send_seq=8296 receive_seq=8296 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998636 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=45.8 th1: temp=44.9 th2: temp=50.3 th3: temp=48.0 sysload=0.14 cputime=276.275 memavail=7397556 print_time=3625.758 buffer_time=2.079 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 80 Hz
Stats 3602.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20572647 bytes_read=2757227 bytes_retransmit=9 bytes_invalid=0 send_seq=366171 receive_seq=366171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015841 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=22594 bytes_read=71593 bytes_retransmit=0 bytes_invalid=0 send_seq=3737 receive_seq=3737 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997209 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=128038 bytes_read=3825621 bytes_retransmit=9 bytes_invalid=0 send_seq=17211 receive_seq=17211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997509 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=74232 bytes_read=1544578 bytes_retransmit=9 bytes_invalid=0 send_seq=9613 receive_seq=9613 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997488 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22861 bytes_read=917323 bytes_retransmit=9 bytes_invalid=0 send_seq=3751 receive_seq=3751 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997615 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23347 bytes_read=70224 bytes_retransmit=9 bytes_invalid=0 send_seq=3738 receive_seq=3738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999434 Octopus_Pro_H723_V1.1: temp=29.4 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77439 bytes_read=1510747 bytes_retransmit=0 bytes_invalid=0 send_seq=8297 receive_seq=8297 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998633 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.4 th1: temp=45.0 th2: temp=50.3 th3: temp=47.9 sysload=0.14 cputime=276.364 memavail=7397556 print_time=3626.694 buffer_time=2.014 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 81 Hz
Stats 3603.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20576767 bytes_read=2757962 bytes_retransmit=9 bytes_invalid=0 send_seq=366256 receive_seq=366256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=0 freq=400015883 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22600 bytes_read=71622 bytes_retransmit=0 bytes_invalid=0 send_seq=3738 receive_seq=3738 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997192 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=128114 bytes_read=3828718 bytes_retransmit=9 bytes_invalid=0 send_seq=17222 receive_seq=17222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997502 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=74238 bytes_read=1544671 bytes_retransmit=9 bytes_invalid=0 send_seq=9614 receive_seq=9614 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997478 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22867 bytes_read=917557 bytes_retransmit=9 bytes_invalid=0 send_seq=3752 receive_seq=3752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997607 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23353 bytes_read=70240 bytes_retransmit=9 bytes_invalid=0 send_seq=3739 receive_seq=3739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77445 bytes_read=1511103 bytes_retransmit=0 bytes_invalid=0 send_seq=8298 receive_seq=8298 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998627 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.3 th1: temp=44.7 th2: temp=50.0 th3: temp=47.9 sysload=0.13 cputime=276.464 memavail=7397556 print_time=3627.899 buffer_time=2.218 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 82 Hz
Stats 3604.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20579669 bytes_read=2758626 bytes_retransmit=9 bytes_invalid=0 send_seq=366321 receive_seq=366321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=0 freq=400015877 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22606 bytes_read=71638 bytes_retransmit=0 bytes_invalid=0 send_seq=3739 receive_seq=3739 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997147 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=128190 bytes_read=3831786 bytes_retransmit=9 bytes_invalid=0 send_seq=17233 receive_seq=17233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997451 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=74244 bytes_read=1544792 bytes_retransmit=9 bytes_invalid=0 send_seq=9615 receive_seq=9615 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997414 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22873 bytes_read=917851 bytes_retransmit=9 bytes_invalid=0 send_seq=3753 receive_seq=3753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997556 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23359 bytes_read=70256 bytes_retransmit=9 bytes_invalid=0 send_seq=3740 receive_seq=3740 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999422 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77451 bytes_read=1511459 bytes_retransmit=0 bytes_invalid=0 send_seq=8299 receive_seq=8299 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998586 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.1 th1: temp=45.0 th2: temp=49.9 th3: temp=48.2 sysload=0.13 cputime=276.555 memavail=7397556 print_time=3628.770 buffer_time=2.089 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 83 Hz
Stats 3605.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20583108 bytes_read=2759328 bytes_retransmit=9 bytes_invalid=0 send_seq=366394 receive_seq=366394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015892 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22618 bytes_read=71670 bytes_retransmit=0 bytes_invalid=0 send_seq=3741 receive_seq=3741 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997168 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=128272 bytes_read=3834859 bytes_retransmit=9 bytes_invalid=0 send_seq=17245 receive_seq=17245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997477 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=74256 bytes_read=1544907 bytes_retransmit=9 bytes_invalid=0 send_seq=9617 receive_seq=9617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997433 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22885 bytes_read=918101 bytes_retransmit=9 bytes_invalid=0 send_seq=3755 receive_seq=3755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997578 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23371 bytes_read=70288 bytes_retransmit=9 bytes_invalid=0 send_seq=3742 receive_seq=3742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999425 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77463 bytes_read=1511831 bytes_retransmit=0 bytes_invalid=0 send_seq=8301 receive_seq=8301 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998598 coil_temp=17.4 refs=0 mcu_temp=20.62 supply_voltage=3.012 th0: temp=45.9 th1: temp=44.8 th2: temp=50.0 th3: temp=48.1 sysload=0.13 cputime=276.648 memavail=7397556 print_time=3629.714 buffer_time=2.031 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 84 Hz
Stats 3606.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20587165 bytes_read=2760058 bytes_retransmit=9 bytes_invalid=0 send_seq=366478 receive_seq=366478 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015952 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22624 bytes_read=71686 bytes_retransmit=0 bytes_invalid=0 send_seq=3742 receive_seq=3742 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997167 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=128348 bytes_read=3837934 bytes_retransmit=9 bytes_invalid=0 send_seq=17256 receive_seq=17256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997443 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=74262 bytes_read=1545007 bytes_retransmit=9 bytes_invalid=0 send_seq=9618 receive_seq=9618 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997415 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22891 bytes_read=918335 bytes_retransmit=9 bytes_invalid=0 send_seq=3756 receive_seq=3756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997583 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23377 bytes_read=70304 bytes_retransmit=9 bytes_invalid=0 send_seq=3743 receive_seq=3743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999419 Octopus_Pro_H723_V1.1: temp=29.3 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77469 bytes_read=1512187 bytes_retransmit=0 bytes_invalid=0 send_seq=8302 receive_seq=8302 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998607 coil_temp=17.4 refs=0 mcu_temp=20.62 supply_voltage=3.012 th0: temp=46.3 th1: temp=44.6 th2: temp=50.1 th3: temp=48.0 sysload=0.13 cputime=276.750 memavail=7396564 print_time=3630.905 buffer_time=2.222 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 85 Hz
Stats 3607.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20590197 bytes_read=2760727 bytes_retransmit=9 bytes_invalid=0 send_seq=366545 receive_seq=366545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015942 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22630 bytes_read=71702 bytes_retransmit=0 bytes_invalid=0 send_seq=3743 receive_seq=3743 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997105 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=128424 bytes_read=3841018 bytes_retransmit=9 bytes_invalid=0 send_seq=17267 receive_seq=17267 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997373 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=74268 bytes_read=1545149 bytes_retransmit=9 bytes_invalid=0 send_seq=9619 receive_seq=9619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997332 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22897 bytes_read=918644 bytes_retransmit=9 bytes_invalid=0 send_seq=3757 receive_seq=3757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997510 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23383 bytes_read=70331 bytes_retransmit=9 bytes_invalid=0 send_seq=3744 receive_seq=3744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999406 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77475 bytes_read=1512543 bytes_retransmit=0 bytes_invalid=0 send_seq=8303 receive_seq=8303 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998558 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.0 th1: temp=45.2 th2: temp=50.1 th3: temp=48.0 sysload=0.13 cputime=276.841 memavail=7396564 print_time=3631.778 buffer_time=2.094 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 86 Hz
Stats 3608.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20593672 bytes_read=2761407 bytes_retransmit=9 bytes_invalid=0 send_seq=366619 receive_seq=366619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015928 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=22636 bytes_read=71731 bytes_retransmit=0 bytes_invalid=0 send_seq=3744 receive_seq=3744 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997131 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=128500 bytes_read=3844075 bytes_retransmit=9 bytes_invalid=0 send_seq=17278 receive_seq=17278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997406 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=74274 bytes_read=1545249 bytes_retransmit=9 bytes_invalid=0 send_seq=9620 receive_seq=9620 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997372 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22903 bytes_read=918878 bytes_retransmit=9 bytes_invalid=0 send_seq=3758 receive_seq=3758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997542 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23389 bytes_read=70347 bytes_retransmit=9 bytes_invalid=0 send_seq=3745 receive_seq=3745 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999413 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77481 bytes_read=1512917 bytes_retransmit=0 bytes_invalid=0 send_seq=8304 receive_seq=8304 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998586 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.2 th1: temp=45.0 th2: temp=50.2 th3: temp=48.1 sysload=0.12 cputime=276.934 memavail=7396564 print_time=3632.715 buffer_time=2.030 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 87 Hz
Stats 3609.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20597881 bytes_read=2762147 bytes_retransmit=9 bytes_invalid=0 send_seq=366705 receive_seq=366705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015918 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=22642 bytes_read=71747 bytes_retransmit=0 bytes_invalid=0 send_seq=3745 receive_seq=3745 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997151 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=128576 bytes_read=3847133 bytes_retransmit=9 bytes_invalid=0 send_seq=17289 receive_seq=17289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997451 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=74280 bytes_read=1545349 bytes_retransmit=9 bytes_invalid=0 send_seq=9621 receive_seq=9621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997411 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22909 bytes_read=919112 bytes_retransmit=9 bytes_invalid=0 send_seq=3759 receive_seq=3759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997594 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23395 bytes_read=70363 bytes_retransmit=9 bytes_invalid=0 send_seq=3746 receive_seq=3746 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999429 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77487 bytes_read=1513273 bytes_retransmit=0 bytes_invalid=0 send_seq=8305 receive_seq=8305 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998649 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.5 th1: temp=44.9 th2: temp=50.0 th3: temp=48.0 sysload=0.12 cputime=277.036 memavail=7396564 print_time=3633.915 buffer_time=2.229 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 88 Hz
Stats 3610.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20600936 bytes_read=2762837 bytes_retransmit=9 bytes_invalid=0 send_seq=366772 receive_seq=366772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015922 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=22648 bytes_read=71763 bytes_retransmit=0 bytes_invalid=0 send_seq=3746 receive_seq=3746 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997176 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=128652 bytes_read=3850277 bytes_retransmit=9 bytes_invalid=0 send_seq=17300 receive_seq=17300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997511 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=74286 bytes_read=1545477 bytes_retransmit=9 bytes_invalid=0 send_seq=9622 receive_seq=9622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997479 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22915 bytes_read=919406 bytes_retransmit=9 bytes_invalid=0 send_seq=3760 receive_seq=3760 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997618 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23401 bytes_read=70379 bytes_retransmit=9 bytes_invalid=0 send_seq=3747 receive_seq=3747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77493 bytes_read=1513629 bytes_retransmit=0 bytes_invalid=0 send_seq=8306 receive_seq=8306 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998654 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.3 th1: temp=44.9 th2: temp=50.3 th3: temp=48.3 sysload=0.12 cputime=277.127 memavail=7396688 print_time=3634.783 buffer_time=2.097 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 89 Hz
Stats 3611.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20604436 bytes_read=2763522 bytes_retransmit=9 bytes_invalid=0 send_seq=366847 receive_seq=366847 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015916 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=22654 bytes_read=71779 bytes_retransmit=0 bytes_invalid=0 send_seq=3747 receive_seq=3747 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997180 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=128728 bytes_read=3853351 bytes_retransmit=9 bytes_invalid=0 send_seq=17311 receive_seq=17311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997664 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=74292 bytes_read=1545577 bytes_retransmit=9 bytes_invalid=0 send_seq=9623 receive_seq=9623 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997467 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22921 bytes_read=919640 bytes_retransmit=9 bytes_invalid=0 send_seq=3761 receive_seq=3761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997606 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23407 bytes_read=70395 bytes_retransmit=9 bytes_invalid=0 send_seq=3748 receive_seq=3748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77499 bytes_read=1513985 bytes_retransmit=0 bytes_invalid=0 send_seq=8307 receive_seq=8307 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998646 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.3 th1: temp=45.1 th2: temp=50.1 th3: temp=48.1 sysload=0.12 cputime=277.220 memavail=7396696 print_time=3635.717 buffer_time=2.030 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 90 Hz
Stats 3612.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20608673 bytes_read=2764267 bytes_retransmit=9 bytes_invalid=0 send_seq=366934 receive_seq=366934 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=47 upcoming_bytes=0 freq=400015903 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=22660 bytes_read=71795 bytes_retransmit=0 bytes_invalid=0 send_seq=3748 receive_seq=3748 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997195 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=128804 bytes_read=3856408 bytes_retransmit=9 bytes_invalid=0 send_seq=17322 receive_seq=17322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997678 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74298 bytes_read=1545691 bytes_retransmit=9 bytes_invalid=0 send_seq=9624 receive_seq=9624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997493 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22927 bytes_read=919889 bytes_retransmit=9 bytes_invalid=0 send_seq=3762 receive_seq=3762 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23413 bytes_read=70422 bytes_retransmit=9 bytes_invalid=0 send_seq=3749 receive_seq=3749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77505 bytes_read=1514341 bytes_retransmit=0 bytes_invalid=0 send_seq=8308 receive_seq=8308 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998644 coil_temp=17.4 refs=0 mcu_temp=20.64 supply_voltage=3.012 th0: temp=46.3 th1: temp=45.0 th2: temp=49.7 th3: temp=48.1 sysload=0.12 cputime=277.322 memavail=7396732 print_time=3636.923 buffer_time=2.236 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 91 Hz
Stats 3613.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20611751 bytes_read=2764936 bytes_retransmit=9 bytes_invalid=0 send_seq=367000 receive_seq=367000 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015903 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22666 bytes_read=71824 bytes_retransmit=0 bytes_invalid=0 send_seq=3749 receive_seq=3749 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997218 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=128880 bytes_read=3859494 bytes_retransmit=9 bytes_invalid=0 send_seq=17333 receive_seq=17333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997669 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74304 bytes_read=1545819 bytes_retransmit=9 bytes_invalid=0 send_seq=9625 receive_seq=9625 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997514 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22933 bytes_read=920183 bytes_retransmit=9 bytes_invalid=0 send_seq=3763 receive_seq=3763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23419 bytes_read=70438 bytes_retransmit=9 bytes_invalid=0 send_seq=3750 receive_seq=3750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77511 bytes_read=1514697 bytes_retransmit=0 bytes_invalid=0 send_seq=8309 receive_seq=8309 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998655 coil_temp=17.4 refs=0 mcu_temp=20.63 supply_voltage=3.012 th0: temp=46.3 th1: temp=44.8 th2: temp=50.2 th3: temp=48.1 sysload=0.11 cputime=277.416 memavail=7396736 print_time=3637.799 buffer_time=2.112 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.9 pwm=0.000
Testing frequency 92 Hz
Stats 3614.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20615372 bytes_read=2765626 bytes_retransmit=9 bytes_invalid=0 send_seq=367076 receive_seq=367076 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015889 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22672 bytes_read=71840 bytes_retransmit=0 bytes_invalid=0 send_seq=3750 receive_seq=3750 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997217 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=128956 bytes_read=3862551 bytes_retransmit=9 bytes_invalid=0 send_seq=17344 receive_seq=17344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997648 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74310 bytes_read=1545919 bytes_retransmit=9 bytes_invalid=0 send_seq=9626 receive_seq=9626 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22939 bytes_read=920417 bytes_retransmit=9 bytes_invalid=0 send_seq=3764 receive_seq=3764 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23425 bytes_read=70454 bytes_retransmit=9 bytes_invalid=0 send_seq=3751 receive_seq=3751 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77517 bytes_read=1515053 bytes_retransmit=0 bytes_invalid=0 send_seq=8310 receive_seq=8310 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998658 coil_temp=17.4 refs=0 mcu_temp=20.62 supply_voltage=3.012 th0: temp=46.1 th1: temp=45.0 th2: temp=50.3 th3: temp=47.9 sysload=0.11 cputime=277.508 memavail=7396736 print_time=3638.734 buffer_time=2.047 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 93 Hz
Stats 3615.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20619695 bytes_read=2766392 bytes_retransmit=9 bytes_invalid=0 send_seq=367164 receive_seq=367164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=0 freq=400015880 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22678 bytes_read=71856 bytes_retransmit=0 bytes_invalid=0 send_seq=3751 receive_seq=3751 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997240 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129032 bytes_read=3865608 bytes_retransmit=9 bytes_invalid=0 send_seq=17355 receive_seq=17355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997653 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74316 bytes_read=1546019 bytes_retransmit=9 bytes_invalid=0 send_seq=9627 receive_seq=9627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22945 bytes_read=920651 bytes_retransmit=9 bytes_invalid=0 send_seq=3765 receive_seq=3765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997669 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23431 bytes_read=70470 bytes_retransmit=9 bytes_invalid=0 send_seq=3752 receive_seq=3752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77523 bytes_read=1515393 bytes_retransmit=0 bytes_invalid=0 send_seq=8311 receive_seq=8311 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998691 coil_temp=17.4 refs=0 mcu_temp=20.59 supply_voltage=3.012 th0: temp=46.4 th1: temp=44.8 th2: temp=50.2 th3: temp=48.2 sysload=0.11 cputime=277.618 memavail=7398764 print_time=3639.931 buffer_time=2.244 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 94 Hz
Stats 3616.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20622760 bytes_read=2767066 bytes_retransmit=9 bytes_invalid=0 send_seq=367231 receive_seq=367231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=15 upcoming_bytes=0 freq=400015867 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22684 bytes_read=71871 bytes_retransmit=0 bytes_invalid=0 send_seq=3752 receive_seq=3752 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997245 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129108 bytes_read=3868711 bytes_retransmit=9 bytes_invalid=0 send_seq=17366 receive_seq=17366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997658 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74322 bytes_read=1546147 bytes_retransmit=9 bytes_invalid=0 send_seq=9628 receive_seq=9628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997550 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22951 bytes_read=920945 bytes_retransmit=9 bytes_invalid=0 send_seq=3766 receive_seq=3766 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23437 bytes_read=70486 bytes_retransmit=9 bytes_invalid=0 send_seq=3753 receive_seq=3753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999454 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77529 bytes_read=1515749 bytes_retransmit=0 bytes_invalid=0 send_seq=8312 receive_seq=8312 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998678 coil_temp=17.3 refs=0 mcu_temp=20.58 supply_voltage=3.012 th0: temp=46.3 th1: temp=45.0 th2: temp=50.2 th3: temp=48.3 sysload=0.11 cputime=277.712 memavail=7398400 print_time=3640.803 buffer_time=2.115 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 95 Hz
Stats 3617.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20626534 bytes_read=2767769 bytes_retransmit=9 bytes_invalid=0 send_seq=367310 receive_seq=367310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015856 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22690 bytes_read=71886 bytes_retransmit=0 bytes_invalid=0 send_seq=3753 receive_seq=3753 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997266 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129184 bytes_read=3871768 bytes_retransmit=9 bytes_invalid=0 send_seq=17377 receive_seq=17377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997683 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74328 bytes_read=1546261 bytes_retransmit=9 bytes_invalid=0 send_seq=9629 receive_seq=9629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22957 bytes_read=921194 bytes_retransmit=9 bytes_invalid=0 send_seq=3767 receive_seq=3767 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23443 bytes_read=70513 bytes_retransmit=9 bytes_invalid=0 send_seq=3754 receive_seq=3754 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999467 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77535 bytes_read=1516105 bytes_retransmit=0 bytes_invalid=0 send_seq=8313 receive_seq=8313 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998683 coil_temp=17.3 refs=0 mcu_temp=20.58 supply_voltage=3.012 th0: temp=46.4 th1: temp=44.8 th2: temp=50.5 th3: temp=48.0 sysload=0.11 cputime=277.806 memavail=7398408 print_time=3641.740 buffer_time=2.052 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 96 Hz
Stats 3618.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20630885 bytes_read=2768514 bytes_retransmit=9 bytes_invalid=0 send_seq=367398 receive_seq=367398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=0 freq=400015848 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22696 bytes_read=71914 bytes_retransmit=0 bytes_invalid=0 send_seq=3754 receive_seq=3754 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997283 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129253 bytes_read=3874859 bytes_retransmit=9 bytes_invalid=0 send_seq=17387 receive_seq=17387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997714 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74334 bytes_read=1546361 bytes_retransmit=9 bytes_invalid=0 send_seq=9630 receive_seq=9630 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997584 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22963 bytes_read=921428 bytes_retransmit=9 bytes_invalid=0 send_seq=3768 receive_seq=3768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999543 adj=47997696 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23449 bytes_read=70529 bytes_retransmit=9 bytes_invalid=0 send_seq=3755 receive_seq=3755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999469 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77541 bytes_read=1516461 bytes_retransmit=0 bytes_invalid=0 send_seq=8314 receive_seq=8314 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998699 coil_temp=17.3 refs=0 mcu_temp=20.57 supply_voltage=3.012 th0: temp=46.5 th1: temp=45.2 th2: temp=50.0 th3: temp=48.4 sysload=0.10 cputime=277.909 memavail=7398408 print_time=3642.944 buffer_time=2.255 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 97 Hz
Stats 3619.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20633931 bytes_read=2769188 bytes_retransmit=9 bytes_invalid=0 send_seq=367465 receive_seq=367465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=22 upcoming_bytes=0 freq=400015839 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22702 bytes_read=71929 bytes_retransmit=0 bytes_invalid=0 send_seq=3755 receive_seq=3755 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997282 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129329 bytes_read=3877944 bytes_retransmit=9 bytes_invalid=0 send_seq=17398 receive_seq=17398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997706 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74340 bytes_read=1546489 bytes_retransmit=9 bytes_invalid=0 send_seq=9631 receive_seq=9631 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997575 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22969 bytes_read=921722 bytes_retransmit=9 bytes_invalid=0 send_seq=3769 receive_seq=3769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997690 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23455 bytes_read=70545 bytes_retransmit=9 bytes_invalid=0 send_seq=3756 receive_seq=3756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77547 bytes_read=1516817 bytes_retransmit=0 bytes_invalid=0 send_seq=8315 receive_seq=8315 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998683 coil_temp=17.3 refs=0 mcu_temp=20.57 supply_voltage=3.012 th0: temp=46.6 th1: temp=44.9 th2: temp=50.3 th3: temp=48.0 sysload=0.10 cputime=278.004 memavail=7398408 print_time=3643.812 buffer_time=2.123 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 98 Hz
Stats 3620.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20637776 bytes_read=2769914 bytes_retransmit=9 bytes_invalid=0 send_seq=367545 receive_seq=367545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015839 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22708 bytes_read=71944 bytes_retransmit=0 bytes_invalid=0 send_seq=3756 receive_seq=3756 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997295 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129405 bytes_read=3881000 bytes_retransmit=9 bytes_invalid=0 send_seq=17409 receive_seq=17409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997698 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74346 bytes_read=1546589 bytes_retransmit=9 bytes_invalid=0 send_seq=9632 receive_seq=9632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997581 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22975 bytes_read=921956 bytes_retransmit=9 bytes_invalid=0 send_seq=3770 receive_seq=3770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997693 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23461 bytes_read=70561 bytes_retransmit=9 bytes_invalid=0 send_seq=3757 receive_seq=3757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999463 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77553 bytes_read=1517173 bytes_retransmit=0 bytes_invalid=0 send_seq=8316 receive_seq=8316 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998685 coil_temp=17.3 refs=0 mcu_temp=20.57 supply_voltage=3.012 th0: temp=46.3 th1: temp=45.2 th2: temp=50.3 th3: temp=48.1 sysload=0.10 cputime=278.100 memavail=7398408 print_time=3644.743 buffer_time=2.054 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 99 Hz
Stats 3621.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20642261 bytes_read=2770679 bytes_retransmit=9 bytes_invalid=0 send_seq=367636 receive_seq=367636 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=0 freq=400015830 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22714 bytes_read=71960 bytes_retransmit=0 bytes_invalid=0 send_seq=3757 receive_seq=3757 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997290 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129481 bytes_read=3884074 bytes_retransmit=9 bytes_invalid=0 send_seq=17420 receive_seq=17420 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997674 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74352 bytes_read=1546689 bytes_retransmit=9 bytes_invalid=0 send_seq=9633 receive_seq=9633 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997574 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22981 bytes_read=922190 bytes_retransmit=9 bytes_invalid=0 send_seq=3771 receive_seq=3771 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23467 bytes_read=70577 bytes_retransmit=9 bytes_invalid=0 send_seq=3758 receive_seq=3758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77559 bytes_read=1517529 bytes_retransmit=0 bytes_invalid=0 send_seq=8317 receive_seq=8317 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998684 coil_temp=17.3 refs=0 mcu_temp=20.59 supply_voltage=3.012 th0: temp=46.3 th1: temp=45.3 th2: temp=50.3 th3: temp=48.4 sysload=0.10 cputime=278.207 memavail=7398408 print_time=3645.943 buffer_time=2.254 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 100 Hz
Stats 3622.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20645380 bytes_read=2771358 bytes_retransmit=9 bytes_invalid=0 send_seq=367704 receive_seq=367704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015818 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22720 bytes_read=71976 bytes_retransmit=0 bytes_invalid=0 send_seq=3758 receive_seq=3758 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997289 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129557 bytes_read=3887158 bytes_retransmit=9 bytes_invalid=0 send_seq=17431 receive_seq=17431 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997672 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74358 bytes_read=1546831 bytes_retransmit=9 bytes_invalid=0 send_seq=9634 receive_seq=9634 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997567 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22987 bytes_read=922499 bytes_retransmit=9 bytes_invalid=0 send_seq=3772 receive_seq=3772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23473 bytes_read=70604 bytes_retransmit=9 bytes_invalid=0 send_seq=3759 receive_seq=3759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77565 bytes_read=1517885 bytes_retransmit=0 bytes_invalid=0 send_seq=8318 receive_seq=8318 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998701 coil_temp=17.3 refs=0 mcu_temp=20.60 supply_voltage=3.012 th0: temp=46.2 th1: temp=45.2 th2: temp=50.4 th3: temp=48.3 sysload=0.10 cputime=278.302 memavail=7398408 print_time=3646.813 buffer_time=2.123 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 101 Hz
Stats 3623.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20649261 bytes_read=2772073 bytes_retransmit=9 bytes_invalid=0 send_seq=367785 receive_seq=367785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=400015822 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22726 bytes_read=72005 bytes_retransmit=0 bytes_invalid=0 send_seq=3759 receive_seq=3759 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997292 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129633 bytes_read=3890214 bytes_retransmit=9 bytes_invalid=0 send_seq=17442 receive_seq=17442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997678 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74364 bytes_read=1546931 bytes_retransmit=9 bytes_invalid=0 send_seq=9635 receive_seq=9635 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997596 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22993 bytes_read=922733 bytes_retransmit=9 bytes_invalid=0 send_seq=3773 receive_seq=3773 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997689 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23479 bytes_read=70619 bytes_retransmit=9 bytes_invalid=0 send_seq=3760 receive_seq=3760 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999456 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77571 bytes_read=1518241 bytes_retransmit=0 bytes_invalid=0 send_seq=8319 receive_seq=8319 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998695 coil_temp=17.3 refs=0 mcu_temp=20.60 supply_voltage=3.012 th0: temp=46.4 th1: temp=45.4 th2: temp=50.4 th3: temp=48.5 sysload=0.09 cputime=278.398 memavail=7398408 print_time=3647.751 buffer_time=2.061 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 102 Hz
Stats 3624.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20653854 bytes_read=2772848 bytes_retransmit=9 bytes_invalid=0 send_seq=367878 receive_seq=367878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015827 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22732 bytes_read=72021 bytes_retransmit=0 bytes_invalid=0 send_seq=3760 receive_seq=3760 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997298 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129709 bytes_read=3893275 bytes_retransmit=9 bytes_invalid=0 send_seq=17453 receive_seq=17453 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997651 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74370 bytes_read=1547031 bytes_retransmit=9 bytes_invalid=0 send_seq=9636 receive_seq=9636 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997584 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=22999 bytes_read=922967 bytes_retransmit=9 bytes_invalid=0 send_seq=3774 receive_seq=3774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23485 bytes_read=70634 bytes_retransmit=9 bytes_invalid=0 send_seq=3761 receive_seq=3761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77577 bytes_read=1518597 bytes_retransmit=0 bytes_invalid=0 send_seq=8320 receive_seq=8320 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998675 coil_temp=17.3 refs=0 mcu_temp=20.60 supply_voltage=3.012 th0: temp=46.3 th1: temp=45.3 th2: temp=50.2 th3: temp=48.3 sysload=0.09 cputime=278.509 memavail=7398408 print_time=3648.952 buffer_time=2.262 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 103 Hz
Stats 3625.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20656957 bytes_read=2773543 bytes_retransmit=9 bytes_invalid=0 send_seq=367946 receive_seq=367946 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=0 freq=400015826 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22738 bytes_read=72037 bytes_retransmit=0 bytes_invalid=0 send_seq=3761 receive_seq=3761 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999214 adj=49997277 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129785 bytes_read=3896360 bytes_retransmit=9 bytes_invalid=0 send_seq=17464 receive_seq=17464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997635 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74376 bytes_read=1547159 bytes_retransmit=9 bytes_invalid=0 send_seq=9637 receive_seq=9637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997548 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23005 bytes_read=923261 bytes_retransmit=9 bytes_invalid=0 send_seq=3775 receive_seq=3775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23491 bytes_read=70649 bytes_retransmit=9 bytes_invalid=0 send_seq=3762 receive_seq=3762 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=30.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77583 bytes_read=1518953 bytes_retransmit=0 bytes_invalid=0 send_seq=8321 receive_seq=8321 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998657 coil_temp=17.3 refs=0 mcu_temp=20.60 supply_voltage=3.012 th0: temp=46.5 th1: temp=45.2 th2: temp=50.4 th3: temp=48.1 sysload=0.09 cputime=278.631 memavail=7390780 print_time=3649.823 buffer_time=2.132 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 104 Hz
Stats 3626.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20660898 bytes_read=2774263 bytes_retransmit=9 bytes_invalid=0 send_seq=368028 receive_seq=368028 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015833 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22744 bytes_read=72053 bytes_retransmit=0 bytes_invalid=0 send_seq=3762 receive_seq=3762 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999215 adj=49997285 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129861 bytes_read=3899494 bytes_retransmit=9 bytes_invalid=0 send_seq=17475 receive_seq=17475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997639 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74382 bytes_read=1547259 bytes_retransmit=9 bytes_invalid=0 send_seq=9638 receive_seq=9638 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997555 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23011 bytes_read=923495 bytes_retransmit=9 bytes_invalid=0 send_seq=3776 receive_seq=3776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23497 bytes_read=70664 bytes_retransmit=9 bytes_invalid=0 send_seq=3763 receive_seq=3763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77589 bytes_read=1519309 bytes_retransmit=0 bytes_invalid=0 send_seq=8322 receive_seq=8322 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998667 coil_temp=17.3 refs=0 mcu_temp=20.60 supply_voltage=3.012 th0: temp=46.3 th1: temp=44.8 th2: temp=50.4 th3: temp=48.2 sysload=0.09 cputime=278.753 memavail=7383428 print_time=3650.754 buffer_time=2.063 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 105 Hz
Stats 3627.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20665653 bytes_read=2775043 bytes_retransmit=9 bytes_invalid=0 send_seq=368122 receive_seq=368122 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015859 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22750 bytes_read=72069 bytes_retransmit=0 bytes_invalid=0 send_seq=3763 receive_seq=3763 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999215 adj=49997280 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129937 bytes_read=3902550 bytes_retransmit=9 bytes_invalid=0 send_seq=17486 receive_seq=17486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997648 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74388 bytes_read=1547373 bytes_retransmit=9 bytes_invalid=0 send_seq=9639 receive_seq=9639 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997545 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23017 bytes_read=923744 bytes_retransmit=9 bytes_invalid=0 send_seq=3777 receive_seq=3777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999541 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23503 bytes_read=70690 bytes_retransmit=9 bytes_invalid=0 send_seq=3764 receive_seq=3764 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77595 bytes_read=1519665 bytes_retransmit=0 bytes_invalid=0 send_seq=8323 receive_seq=8323 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998668 coil_temp=17.3 refs=0 mcu_temp=20.59 supply_voltage=3.012 th0: temp=46.4 th1: temp=45.1 th2: temp=50.7 th3: temp=48.2 sysload=0.09 cputime=278.884 memavail=7384860 print_time=3651.959 buffer_time=2.268 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 106 Hz
Stats 3628.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20668716 bytes_read=2775713 bytes_retransmit=9 bytes_invalid=0 send_seq=368189 receive_seq=368189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=22 upcoming_bytes=0 freq=400015918 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22756 bytes_read=72098 bytes_retransmit=0 bytes_invalid=0 send_seq=3764 receive_seq=3764 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997231 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130013 bytes_read=3905634 bytes_retransmit=9 bytes_invalid=0 send_seq=17497 receive_seq=17497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997597 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74394 bytes_read=1547501 bytes_retransmit=9 bytes_invalid=0 send_seq=9640 receive_seq=9640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997481 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23023 bytes_read=924038 bytes_retransmit=9 bytes_invalid=0 send_seq=3778 receive_seq=3778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997607 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23509 bytes_read=70704 bytes_retransmit=9 bytes_invalid=0 send_seq=3765 receive_seq=3765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77601 bytes_read=1520021 bytes_retransmit=0 bytes_invalid=0 send_seq=8324 receive_seq=8324 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998638 coil_temp=17.3 refs=0 mcu_temp=20.58 supply_voltage=3.012 th0: temp=46.6 th1: temp=45.1 th2: temp=50.4 th3: temp=48.4 sysload=0.25 cputime=279.000 memavail=7384092 print_time=3652.819 buffer_time=2.127 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 107 Hz
Stats 3629.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20672755 bytes_read=2776438 bytes_retransmit=9 bytes_invalid=0 send_seq=368272 receive_seq=368272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=400015911 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22762 bytes_read=72114 bytes_retransmit=0 bytes_invalid=0 send_seq=3765 receive_seq=3765 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997151 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130089 bytes_read=3908690 bytes_retransmit=9 bytes_invalid=0 send_seq=17508 receive_seq=17508 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997478 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74400 bytes_read=1547601 bytes_retransmit=9 bytes_invalid=0 send_seq=9641 receive_seq=9641 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997367 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23029 bytes_read=924272 bytes_retransmit=9 bytes_invalid=0 send_seq=3779 receive_seq=3779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997630 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23515 bytes_read=70719 bytes_retransmit=9 bytes_invalid=0 send_seq=3766 receive_seq=3766 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999414 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=30.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77607 bytes_read=1520377 bytes_retransmit=0 bytes_invalid=0 send_seq=8325 receive_seq=8325 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998587 coil_temp=17.3 refs=0 mcu_temp=20.57 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.6 th2: temp=50.4 th3: temp=48.3 sysload=0.25 cputime=279.113 memavail=7377244 print_time=3653.756 buffer_time=2.064 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 108 Hz
Stats 3630.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20677465 bytes_read=2777239 bytes_retransmit=9 bytes_invalid=0 send_seq=368367 receive_seq=368367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015902 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22768 bytes_read=72130 bytes_retransmit=0 bytes_invalid=0 send_seq=3766 receive_seq=3766 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997180 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130158 bytes_read=3911724 bytes_retransmit=9 bytes_invalid=0 send_seq=17518 receive_seq=17518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000193 adj=63997507 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74406 bytes_read=1547701 bytes_retransmit=9 bytes_invalid=0 send_seq=9642 receive_seq=9642 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997397 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23035 bytes_read=924506 bytes_retransmit=9 bytes_invalid=0 send_seq=3780 receive_seq=3780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997689 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23521 bytes_read=70734 bytes_retransmit=9 bytes_invalid=0 send_seq=3767 receive_seq=3767 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999419 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77613 bytes_read=1520733 bytes_retransmit=0 bytes_invalid=0 send_seq=8326 receive_seq=8326 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998623 coil_temp=17.3 refs=0 mcu_temp=20.56 supply_voltage=3.012 th0: temp=46.8 th1: temp=45.2 th2: temp=50.5 th3: temp=48.3 sysload=0.25 cputime=279.233 memavail=7377216 print_time=3654.955 buffer_time=2.263 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 109 Hz
Stats 3631.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20680733 bytes_read=2777928 bytes_retransmit=9 bytes_invalid=0 send_seq=368437 receive_seq=368437 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=0 freq=400015906 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22774 bytes_read=72146 bytes_retransmit=0 bytes_invalid=0 send_seq=3767 receive_seq=3767 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999218 adj=49997214 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130234 bytes_read=3914827 bytes_retransmit=9 bytes_invalid=0 send_seq=17529 receive_seq=17529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997570 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74412 bytes_read=1547829 bytes_retransmit=9 bytes_invalid=0 send_seq=9643 receive_seq=9643 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997439 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23041 bytes_read=924800 bytes_retransmit=9 bytes_invalid=0 send_seq=3781 receive_seq=3781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997711 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23527 bytes_read=70749 bytes_retransmit=9 bytes_invalid=0 send_seq=3768 receive_seq=3768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=30.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77619 bytes_read=1521089 bytes_retransmit=0 bytes_invalid=0 send_seq=8327 receive_seq=8327 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998635 coil_temp=17.3 refs=0 mcu_temp=20.56 supply_voltage=3.012 th0: temp=46.6 th1: temp=45.3 th2: temp=50.4 th3: temp=48.3 sysload=0.25 cputime=279.345 memavail=7377436 print_time=3655.835 buffer_time=2.142 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 110 Hz
Stats 3632.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20684859 bytes_read=2778663 bytes_retransmit=9 bytes_invalid=0 send_seq=368522 receive_seq=368522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015917 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22780 bytes_read=72162 bytes_retransmit=0 bytes_invalid=0 send_seq=3768 receive_seq=3768 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999219 adj=49997215 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130310 bytes_read=3917883 bytes_retransmit=9 bytes_invalid=0 send_seq=17540 receive_seq=17540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997649 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74418 bytes_read=1547929 bytes_retransmit=9 bytes_invalid=0 send_seq=9644 receive_seq=9644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997473 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23047 bytes_read=925049 bytes_retransmit=9 bytes_invalid=0 send_seq=3782 receive_seq=3782 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997698 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23533 bytes_read=70775 bytes_retransmit=9 bytes_invalid=0 send_seq=3769 receive_seq=3769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77625 bytes_read=1521445 bytes_retransmit=0 bytes_invalid=0 send_seq=8328 receive_seq=8328 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998623 coil_temp=17.3 refs=0 mcu_temp=20.56 supply_voltage=3.012 th0: temp=46.4 th1: temp=45.3 th2: temp=50.4 th3: temp=48.3 sysload=0.25 cputime=279.466 memavail=7386740 print_time=3656.763 buffer_time=2.066 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 111 Hz
Stats 3633.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20689618 bytes_read=2779448 bytes_retransmit=9 bytes_invalid=0 send_seq=368617 receive_seq=368617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=400015907 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=22786 bytes_read=72191 bytes_retransmit=0 bytes_invalid=0 send_seq=3769 receive_seq=3769 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999219 adj=49997215 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130386 bytes_read=3921012 bytes_retransmit=9 bytes_invalid=0 send_seq=17551 receive_seq=17551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997614 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74424 bytes_read=1548043 bytes_retransmit=9 bytes_invalid=0 send_seq=9645 receive_seq=9645 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997451 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23053 bytes_read=925283 bytes_retransmit=9 bytes_invalid=0 send_seq=3783 receive_seq=3783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23539 bytes_read=70790 bytes_retransmit=9 bytes_invalid=0 send_seq=3770 receive_seq=3770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999428 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=30.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77631 bytes_read=1521801 bytes_retransmit=0 bytes_invalid=0 send_seq=8329 receive_seq=8329 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998610 coil_temp=17.3 refs=0 mcu_temp=20.56 supply_voltage=3.012 th0: temp=46.6 th1: temp=45.3 th2: temp=50.5 th3: temp=48.5 sysload=0.31 cputime=279.598 memavail=7378520 print_time=3657.961 buffer_time=2.263 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 112 Hz
Stats 3634.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20692809 bytes_read=2780127 bytes_retransmit=9 bytes_invalid=0 send_seq=368685 receive_seq=368685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=0 freq=400015891 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=22792 bytes_read=72207 bytes_retransmit=0 bytes_invalid=0 send_seq=3770 receive_seq=3770 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999219 adj=49997235 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130462 bytes_read=3924085 bytes_retransmit=9 bytes_invalid=0 send_seq=17562 receive_seq=17562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997632 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74430 bytes_read=1548171 bytes_retransmit=9 bytes_invalid=0 send_seq=9646 receive_seq=9646 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997486 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23059 bytes_read=925577 bytes_retransmit=9 bytes_invalid=0 send_seq=3784 receive_seq=3784 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23545 bytes_read=70805 bytes_retransmit=9 bytes_invalid=0 send_seq=3771 receive_seq=3771 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77637 bytes_read=1522157 bytes_retransmit=0 bytes_invalid=0 send_seq=8330 receive_seq=8330 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998635 coil_temp=17.3 refs=0 mcu_temp=20.56 supply_voltage=3.012 th0: temp=46.5 th1: temp=45.4 th2: temp=50.3 th3: temp=48.2 sysload=0.31 cputime=279.724 memavail=7366556 print_time=3658.833 buffer_time=2.132 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 113 Hz
Stats 3635.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20696951 bytes_read=2780863 bytes_retransmit=9 bytes_invalid=0 send_seq=368767 receive_seq=368767 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015895 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=22798 bytes_read=72223 bytes_retransmit=0 bytes_invalid=0 send_seq=3771 receive_seq=3771 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999219 adj=49997260 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130538 bytes_read=3927143 bytes_retransmit=9 bytes_invalid=0 send_seq=17573 receive_seq=17573 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997734 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74436 bytes_read=1548271 bytes_retransmit=9 bytes_invalid=0 send_seq=9647 receive_seq=9647 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997512 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23065 bytes_read=925811 bytes_retransmit=9 bytes_invalid=0 send_seq=3785 receive_seq=3785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23551 bytes_read=70820 bytes_retransmit=9 bytes_invalid=0 send_seq=3772 receive_seq=3772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=31.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77643 bytes_read=1522513 bytes_retransmit=0 bytes_invalid=0 send_seq=8331 receive_seq=8331 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998651 coil_temp=17.3 refs=0 mcu_temp=20.55 supply_voltage=3.012 th0: temp=46.6 th1: temp=45.2 th2: temp=50.6 th3: temp=48.2 sysload=0.31 cputime=279.857 memavail=7361084 print_time=3659.772 buffer_time=2.068 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 114 Hz
Stats 3636.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20701790 bytes_read=2781658 bytes_retransmit=9 bytes_invalid=0 send_seq=368864 receive_seq=368864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015894 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=22804 bytes_read=72239 bytes_retransmit=0 bytes_invalid=0 send_seq=3772 receive_seq=3772 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999220 adj=49997244 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130614 bytes_read=3930230 bytes_retransmit=9 bytes_invalid=0 send_seq=17584 receive_seq=17584 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997701 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74442 bytes_read=1548385 bytes_retransmit=9 bytes_invalid=0 send_seq=9648 receive_seq=9648 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23071 bytes_read=926045 bytes_retransmit=9 bytes_invalid=0 send_seq=3786 receive_seq=3786 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23557 bytes_read=70835 bytes_retransmit=9 bytes_invalid=0 send_seq=3773 receive_seq=3773 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=30.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77649 bytes_read=1522869 bytes_retransmit=0 bytes_invalid=0 send_seq=8332 receive_seq=8332 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998639 coil_temp=17.3 refs=0 mcu_temp=20.54 supply_voltage=3.012 th0: temp=46.6 th1: temp=45.1 th2: temp=50.6 th3: temp=48.3 sysload=0.31 cputime=280.002 memavail=7394836 print_time=3660.969 buffer_time=2.263 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 115 Hz
Stats 3637.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20705099 bytes_read=2782357 bytes_retransmit=9 bytes_invalid=0 send_seq=368936 receive_seq=368936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015889 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=22810 bytes_read=72255 bytes_retransmit=0 bytes_invalid=0 send_seq=3773 receive_seq=3773 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999221 adj=49997255 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130690 bytes_read=3933358 bytes_retransmit=9 bytes_invalid=0 send_seq=17595 receive_seq=17595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997680 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74448 bytes_read=1548499 bytes_retransmit=9 bytes_invalid=0 send_seq=9649 receive_seq=9649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23077 bytes_read=926354 bytes_retransmit=9 bytes_invalid=0 send_seq=3787 receive_seq=3787 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23563 bytes_read=70861 bytes_retransmit=9 bytes_invalid=0 send_seq=3774 receive_seq=3774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=30.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77655 bytes_read=1523225 bytes_retransmit=0 bytes_invalid=0 send_seq=8333 receive_seq=8333 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998638 coil_temp=17.3 refs=0 mcu_temp=20.54 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.4 th2: temp=50.3 th3: temp=48.4 sysload=0.31 cputime=280.131 memavail=7393784 print_time=3661.840 buffer_time=2.131 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 116 Hz
Stats 3638.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20709288 bytes_read=2783082 bytes_retransmit=9 bytes_invalid=0 send_seq=369019 receive_seq=369019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015890 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=22816 bytes_read=72284 bytes_retransmit=0 bytes_invalid=0 send_seq=3774 receive_seq=3774 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999226 adj=49997274 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130766 bytes_read=3936418 bytes_retransmit=9 bytes_invalid=0 send_seq=17606 receive_seq=17606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997669 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74454 bytes_read=1548613 bytes_retransmit=9 bytes_invalid=0 send_seq=9650 receive_seq=9650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997564 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23083 bytes_read=926588 bytes_retransmit=9 bytes_invalid=0 send_seq=3788 receive_seq=3788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23569 bytes_read=70876 bytes_retransmit=9 bytes_invalid=0 send_seq=3775 receive_seq=3775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=30.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77661 bytes_read=1523581 bytes_retransmit=0 bytes_invalid=0 send_seq=8334 receive_seq=8334 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998648 coil_temp=17.3 refs=0 mcu_temp=20.55 supply_voltage=3.012 th0: temp=46.9 th1: temp=45.4 th2: temp=50.5 th3: temp=48.4 sysload=0.36 cputime=280.254 memavail=7387600 print_time=3662.775 buffer_time=2.065 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 117 Hz
Stats 3639.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20714115 bytes_read=2783868 bytes_retransmit=9 bytes_invalid=0 send_seq=369115 receive_seq=369115 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=400015922 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=22822 bytes_read=72300 bytes_retransmit=0 bytes_invalid=0 send_seq=3775 receive_seq=3775 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999226 adj=49997333 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130842 bytes_read=3939492 bytes_retransmit=9 bytes_invalid=0 send_seq=17617 receive_seq=17617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997666 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74460 bytes_read=1548727 bytes_retransmit=9 bytes_invalid=0 send_seq=9651 receive_seq=9651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997560 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23089 bytes_read=926837 bytes_retransmit=9 bytes_invalid=0 send_seq=3789 receive_seq=3789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23575 bytes_read=70891 bytes_retransmit=9 bytes_invalid=0 send_seq=3776 receive_seq=3776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999454 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77667 bytes_read=1523937 bytes_retransmit=0 bytes_invalid=0 send_seq=8335 receive_seq=8335 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998654 coil_temp=17.3 refs=0 mcu_temp=20.54 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.3 th2: temp=50.4 th3: temp=48.5 sysload=0.36 cputime=280.394 memavail=7387784 print_time=3663.974 buffer_time=2.261 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 118 Hz
Stats 3640.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20717430 bytes_read=2784578 bytes_retransmit=9 bytes_invalid=0 send_seq=369186 receive_seq=369186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015934 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=22828 bytes_read=72316 bytes_retransmit=0 bytes_invalid=0 send_seq=3776 receive_seq=3776 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999229 adj=49997264 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130918 bytes_read=3942562 bytes_retransmit=9 bytes_invalid=0 send_seq=17628 receive_seq=17628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997611 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74466 bytes_read=1548841 bytes_retransmit=9 bytes_invalid=0 send_seq=9652 receive_seq=9652 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23095 bytes_read=927116 bytes_retransmit=9 bytes_invalid=0 send_seq=3790 receive_seq=3790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997597 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23581 bytes_read=70906 bytes_retransmit=9 bytes_invalid=0 send_seq=3777 receive_seq=3777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=30.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77673 bytes_read=1524293 bytes_retransmit=0 bytes_invalid=0 send_seq=8336 receive_seq=8336 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998629 coil_temp=17.3 refs=0 mcu_temp=20.54 supply_voltage=3.012 th0: temp=46.6 th1: temp=45.4 th2: temp=50.6 th3: temp=48.5 sysload=0.36 cputime=280.521 memavail=7392100 print_time=3664.851 buffer_time=2.134 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 119 Hz
Stats 3641.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20721711 bytes_read=2785318 bytes_retransmit=9 bytes_invalid=0 send_seq=369272 receive_seq=369272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015965 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=22834 bytes_read=72332 bytes_retransmit=0 bytes_invalid=0 send_seq=3777 receive_seq=3777 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997279 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130994 bytes_read=3945635 bytes_retransmit=9 bytes_invalid=0 send_seq=17639 receive_seq=17639 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997587 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74472 bytes_read=1548941 bytes_retransmit=9 bytes_invalid=0 send_seq=9653 receive_seq=9653 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997470 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23101 bytes_read=927350 bytes_retransmit=9 bytes_invalid=0 send_seq=3791 receive_seq=3791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997574 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23587 bytes_read=70921 bytes_retransmit=9 bytes_invalid=0 send_seq=3778 receive_seq=3778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999434 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=30.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77679 bytes_read=1524649 bytes_retransmit=0 bytes_invalid=0 send_seq=8337 receive_seq=8337 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998613 coil_temp=17.3 refs=0 mcu_temp=20.53 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.6 th2: temp=50.2 th3: temp=48.5 sysload=0.36 cputime=280.632 memavail=7392884 print_time=3665.779 buffer_time=2.061 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 120 Hz
Stats 3642.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20726570 bytes_read=2786113 bytes_retransmit=9 bytes_invalid=0 send_seq=369369 receive_seq=369369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015950 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=22840 bytes_read=72348 bytes_retransmit=0 bytes_invalid=0 send_seq=3778 receive_seq=3778 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997291 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131070 bytes_read=3948778 bytes_retransmit=9 bytes_invalid=0 send_seq=17650 receive_seq=17650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997541 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74478 bytes_read=1549055 bytes_retransmit=9 bytes_invalid=0 send_seq=9654 receive_seq=9654 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997417 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23107 bytes_read=927614 bytes_retransmit=9 bytes_invalid=0 send_seq=3792 receive_seq=3792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997530 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23593 bytes_read=70947 bytes_retransmit=9 bytes_invalid=0 send_seq=3779 receive_seq=3779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999422 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77685 bytes_read=1525005 bytes_retransmit=0 bytes_invalid=0 send_seq=8338 receive_seq=8338 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998587 coil_temp=17.3 refs=0 mcu_temp=20.53 supply_voltage=3.012 th0: temp=46.4 th1: temp=45.4 th2: temp=50.6 th3: temp=48.5 sysload=0.36 cputime=280.747 memavail=7392884 print_time=3666.975 buffer_time=2.257 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 121 Hz
Stats 3643.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20729940 bytes_read=2786817 bytes_retransmit=9 bytes_invalid=0 send_seq=369442 receive_seq=369442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=0 freq=400015932 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22846 bytes_read=72377 bytes_retransmit=0 bytes_invalid=0 send_seq=3779 receive_seq=3779 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999232 adj=49997285 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131146 bytes_read=3951834 bytes_retransmit=9 bytes_invalid=0 send_seq=17661 receive_seq=17661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997596 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74484 bytes_read=1549183 bytes_retransmit=9 bytes_invalid=0 send_seq=9655 receive_seq=9655 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997471 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23113 bytes_read=927893 bytes_retransmit=9 bytes_invalid=0 send_seq=3793 receive_seq=3793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997586 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23599 bytes_read=70962 bytes_retransmit=9 bytes_invalid=0 send_seq=3780 receive_seq=3780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999434 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77691 bytes_read=1525361 bytes_retransmit=0 bytes_invalid=0 send_seq=8339 receive_seq=8339 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998619 coil_temp=17.3 refs=0 mcu_temp=20.53 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.5 th2: temp=50.4 th3: temp=48.6 sysload=0.33 cputime=280.847 memavail=7392884 print_time=3667.854 buffer_time=2.136 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 122 Hz
Stats 3644.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20734269 bytes_read=2787547 bytes_retransmit=9 bytes_invalid=0 send_seq=369526 receive_seq=369526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015939 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22852 bytes_read=72393 bytes_retransmit=0 bytes_invalid=0 send_seq=3780 receive_seq=3780 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999230 adj=49997288 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131222 bytes_read=3954890 bytes_retransmit=9 bytes_invalid=0 send_seq=17672 receive_seq=17672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997623 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74490 bytes_read=1549283 bytes_retransmit=9 bytes_invalid=0 send_seq=9656 receive_seq=9656 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23119 bytes_read=928127 bytes_retransmit=9 bytes_invalid=0 send_seq=3794 receive_seq=3794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997608 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23605 bytes_read=70977 bytes_retransmit=9 bytes_invalid=0 send_seq=3781 receive_seq=3781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77697 bytes_read=1525717 bytes_retransmit=0 bytes_invalid=0 send_seq=8340 receive_seq=8340 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998639 coil_temp=17.3 refs=0 mcu_temp=20.53 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.5 th2: temp=50.7 th3: temp=48.5 sysload=0.33 cputime=280.950 memavail=7392884 print_time=3668.779 buffer_time=2.059 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 123 Hz
Stats 3645.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20739217 bytes_read=2788353 bytes_retransmit=9 bytes_invalid=0 send_seq=369622 receive_seq=369622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=56 freq=400015939 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22858 bytes_read=72409 bytes_retransmit=0 bytes_invalid=0 send_seq=3781 receive_seq=3781 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999229 adj=49997248 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131298 bytes_read=3957977 bytes_retransmit=9 bytes_invalid=0 send_seq=17683 receive_seq=17683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997611 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74496 bytes_read=1549397 bytes_retransmit=9 bytes_invalid=0 send_seq=9657 receive_seq=9657 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997471 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23125 bytes_read=928362 bytes_retransmit=9 bytes_invalid=0 send_seq=3795 receive_seq=3795 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997611 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23611 bytes_read=70992 bytes_retransmit=9 bytes_invalid=0 send_seq=3782 receive_seq=3782 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77703 bytes_read=1526073 bytes_retransmit=0 bytes_invalid=0 send_seq=8341 receive_seq=8341 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998626 coil_temp=17.3 refs=0 mcu_temp=20.53 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.4 th2: temp=50.4 th3: temp=48.4 sysload=0.33 cputime=281.067 memavail=7392884 print_time=3669.980 buffer_time=2.260 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 124 Hz
Stats 3646.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20742597 bytes_read=2789052 bytes_retransmit=9 bytes_invalid=0 send_seq=369694 receive_seq=369694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=0 freq=400015944 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22864 bytes_read=72425 bytes_retransmit=0 bytes_invalid=0 send_seq=3782 receive_seq=3782 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999228 adj=49997230 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131367 bytes_read=3961030 bytes_retransmit=9 bytes_invalid=0 send_seq=17693 receive_seq=17693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997616 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74502 bytes_read=1549511 bytes_retransmit=9 bytes_invalid=0 send_seq=9658 receive_seq=9658 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23131 bytes_read=928622 bytes_retransmit=9 bytes_invalid=0 send_seq=3796 receive_seq=3796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23617 bytes_read=71008 bytes_retransmit=9 bytes_invalid=0 send_seq=3783 receive_seq=3783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77709 bytes_read=1526429 bytes_retransmit=0 bytes_invalid=0 send_seq=8342 receive_seq=8342 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998626 coil_temp=17.3 refs=0 mcu_temp=20.52 supply_voltage=3.012 th0: temp=46.5 th1: temp=45.4 th2: temp=50.6 th3: temp=48.6 sysload=0.33 cputime=281.171 memavail=7396036 print_time=3670.854 buffer_time=2.133 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 125 Hz
Stats 3647.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20747005 bytes_read=2789792 bytes_retransmit=9 bytes_invalid=0 send_seq=369780 receive_seq=369780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015947 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22870 bytes_read=72441 bytes_retransmit=0 bytes_invalid=0 send_seq=3783 receive_seq=3783 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999227 adj=49997212 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131443 bytes_read=3964090 bytes_retransmit=9 bytes_invalid=0 send_seq=17704 receive_seq=17704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997597 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74508 bytes_read=1549611 bytes_retransmit=9 bytes_invalid=0 send_seq=9659 receive_seq=9659 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997465 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23137 bytes_read=928855 bytes_retransmit=9 bytes_invalid=0 send_seq=3797 receive_seq=3797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997605 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23623 bytes_read=71035 bytes_retransmit=9 bytes_invalid=0 send_seq=3784 receive_seq=3784 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77715 bytes_read=1526785 bytes_retransmit=0 bytes_invalid=0 send_seq=8343 receive_seq=8343 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998618 coil_temp=17.3 refs=0 mcu_temp=20.53 supply_voltage=3.012 th0: temp=47.0 th1: temp=45.6 th2: temp=50.6 th3: temp=48.5 sysload=0.33 cputime=281.280 memavail=7395580 print_time=3671.784 buffer_time=2.063 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 126 Hz
Stats 3648.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20751930 bytes_read=2790582 bytes_retransmit=9 bytes_invalid=0 send_seq=369876 receive_seq=369876 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=120 freq=400015942 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22876 bytes_read=72470 bytes_retransmit=0 bytes_invalid=0 send_seq=3784 receive_seq=3784 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999226 adj=49997194 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131519 bytes_read=3967175 bytes_retransmit=9 bytes_invalid=0 send_seq=17715 receive_seq=17715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997584 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74514 bytes_read=1549739 bytes_retransmit=9 bytes_invalid=0 send_seq=9660 receive_seq=9660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997456 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23143 bytes_read=929087 bytes_retransmit=9 bytes_invalid=0 send_seq=3798 receive_seq=3798 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997593 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23629 bytes_read=71051 bytes_retransmit=9 bytes_invalid=0 send_seq=3785 receive_seq=3785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77721 bytes_read=1527141 bytes_retransmit=0 bytes_invalid=0 send_seq=8344 receive_seq=8344 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998616 coil_temp=17.3 refs=0 mcu_temp=20.53 supply_voltage=3.012 th0: temp=46.8 th1: temp=45.3 th2: temp=50.6 th3: temp=48.5 sysload=0.31 cputime=281.399 memavail=7395584 print_time=3672.984 buffer_time=2.263 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 127 Hz
Stats 3649.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20755347 bytes_read=2791286 bytes_retransmit=9 bytes_invalid=0 send_seq=369949 receive_seq=369949 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=0 freq=400016059 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22882 bytes_read=72486 bytes_retransmit=0 bytes_invalid=0 send_seq=3785 receive_seq=3785 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999226 adj=49997201 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131595 bytes_read=3970289 bytes_retransmit=9 bytes_invalid=0 send_seq=17726 receive_seq=17726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997605 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74520 bytes_read=1549853 bytes_retransmit=9 bytes_invalid=0 send_seq=9661 receive_seq=9661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997469 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23149 bytes_read=929347 bytes_retransmit=9 bytes_invalid=0 send_seq=3799 receive_seq=3799 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997605 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23635 bytes_read=71067 bytes_retransmit=9 bytes_invalid=0 send_seq=3786 receive_seq=3786 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77727 bytes_read=1527497 bytes_retransmit=0 bytes_invalid=0 send_seq=8345 receive_seq=8345 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999922 adj=31998626 coil_temp=17.3 refs=0 mcu_temp=20.54 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.5 th2: temp=50.6 th3: temp=48.5 sysload=0.31 cputime=281.508 memavail=7390292 print_time=3673.858 buffer_time=2.135 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 128 Hz
Stats 3650.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20759815 bytes_read=2792048 bytes_retransmit=9 bytes_invalid=0 send_seq=370037 receive_seq=370037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=400016146 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22888 bytes_read=72502 bytes_retransmit=0 bytes_invalid=0 send_seq=3786 receive_seq=3786 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999227 adj=49997026 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131671 bytes_read=3973345 bytes_retransmit=9 bytes_invalid=0 send_seq=17737 receive_seq=17737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997379 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74526 bytes_read=1549953 bytes_retransmit=9 bytes_invalid=0 send_seq=9662 receive_seq=9662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997231 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23155 bytes_read=929569 bytes_retransmit=9 bytes_invalid=0 send_seq=3800 receive_seq=3800 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997431 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23641 bytes_read=71083 bytes_retransmit=9 bytes_invalid=0 send_seq=3787 receive_seq=3787 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999398 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77733 bytes_read=1527853 bytes_retransmit=0 bytes_invalid=0 send_seq=8346 receive_seq=8346 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998537 coil_temp=17.3 refs=0 mcu_temp=20.55 supply_voltage=3.012 th0: temp=46.5 th1: temp=45.5 th2: temp=50.5 th3: temp=48.6 sysload=0.31 cputime=281.618 memavail=7395716 print_time=3674.785 buffer_time=2.062 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 129 Hz
Stats 3651.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20764688 bytes_read=2792833 bytes_retransmit=9 bytes_invalid=0 send_seq=370132 receive_seq=370132 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=216 freq=400016134 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22894 bytes_read=72518 bytes_retransmit=0 bytes_invalid=0 send_seq=3787 receive_seq=3787 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999226 adj=49996918 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131747 bytes_read=3976447 bytes_retransmit=9 bytes_invalid=0 send_seq=17748 receive_seq=17748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997229 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74532 bytes_read=1550067 bytes_retransmit=9 bytes_invalid=0 send_seq=9663 receive_seq=9663 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997082 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23161 bytes_read=929833 bytes_retransmit=9 bytes_invalid=0 send_seq=3801 receive_seq=3801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997319 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23647 bytes_read=71099 bytes_retransmit=9 bytes_invalid=0 send_seq=3788 receive_seq=3788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999371 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77739 bytes_read=1528209 bytes_retransmit=0 bytes_invalid=0 send_seq=8347 receive_seq=8347 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998489 coil_temp=17.3 refs=0 mcu_temp=20.55 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.5 th2: temp=50.8 th3: temp=48.8 sysload=0.31 cputime=281.737 memavail=7395716 print_time=3675.989 buffer_time=2.265 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=19.0 pwm=0.000
Testing frequency 130 Hz
Stats 3652.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20768259 bytes_read=2793542 bytes_retransmit=9 bytes_invalid=0 send_seq=370206 receive_seq=370206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=0 freq=400016106 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22900 bytes_read=72534 bytes_retransmit=0 bytes_invalid=0 send_seq=3788 receive_seq=3788 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999224 adj=49997012 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131823 bytes_read=3979507 bytes_retransmit=9 bytes_invalid=0 send_seq=17759 receive_seq=17759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997359 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74538 bytes_read=1550181 bytes_retransmit=9 bytes_invalid=0 send_seq=9664 receive_seq=9664 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997217 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23167 bytes_read=930112 bytes_retransmit=9 bytes_invalid=0 send_seq=3802 receive_seq=3802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997418 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23653 bytes_read=71126 bytes_retransmit=9 bytes_invalid=0 send_seq=3789 receive_seq=3789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999392 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77745 bytes_read=1528565 bytes_retransmit=0 bytes_invalid=0 send_seq=8348 receive_seq=8348 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998540 coil_temp=17.3 refs=0 mcu_temp=20.56 supply_voltage=3.012 th0: temp=46.8 th1: temp=45.4 th2: temp=50.5 th3: temp=48.6 sysload=0.31 cputime=281.842 memavail=7395716 print_time=3676.861 buffer_time=2.137 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 131 Hz
Stats 3653.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20772726 bytes_read=2794297 bytes_retransmit=9 bytes_invalid=0 send_seq=370295 receive_seq=370295 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=400016146 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22906 bytes_read=72563 bytes_retransmit=0 bytes_invalid=0 send_seq=3789 receive_seq=3789 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999222 adj=49997054 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131899 bytes_read=3982566 bytes_retransmit=9 bytes_invalid=0 send_seq=17770 receive_seq=17770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997454 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74544 bytes_read=1550295 bytes_retransmit=9 bytes_invalid=0 send_seq=9665 receive_seq=9665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997294 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23173 bytes_read=930346 bytes_retransmit=9 bytes_invalid=0 send_seq=3803 receive_seq=3803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997478 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23659 bytes_read=71142 bytes_retransmit=9 bytes_invalid=0 send_seq=3790 receive_seq=3790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999405 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77751 bytes_read=1528921 bytes_retransmit=0 bytes_invalid=0 send_seq=8349 receive_seq=8349 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998570 coil_temp=17.3 refs=0 mcu_temp=20.57 supply_voltage=3.012 th0: temp=46.6 th1: temp=45.8 th2: temp=50.7 th3: temp=48.6 sysload=0.28 cputime=281.950 memavail=7395724 print_time=3677.787 buffer_time=2.062 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 132 Hz
Stats 3654.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20777582 bytes_read=2795087 bytes_retransmit=9 bytes_invalid=0 send_seq=370391 receive_seq=370391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=291 freq=400016123 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22912 bytes_read=72579 bytes_retransmit=0 bytes_invalid=0 send_seq=3790 receive_seq=3790 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999220 adj=49996990 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131975 bytes_read=3985651 bytes_retransmit=9 bytes_invalid=0 send_seq=17781 receive_seq=17781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997420 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74550 bytes_read=1550409 bytes_retransmit=9 bytes_invalid=0 send_seq=9666 receive_seq=9666 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997231 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23179 bytes_read=930610 bytes_retransmit=9 bytes_invalid=0 send_seq=3804 receive_seq=3804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997430 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23665 bytes_read=71158 bytes_retransmit=9 bytes_invalid=0 send_seq=3791 receive_seq=3791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999391 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77757 bytes_read=1529277 bytes_retransmit=0 bytes_invalid=0 send_seq=8350 receive_seq=8350 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998638 coil_temp=17.3 refs=0 mcu_temp=20.56 supply_voltage=3.012 th0: temp=47.1 th1: temp=45.7 th2: temp=50.8 th3: temp=48.6 sysload=0.28 cputime=282.071 memavail=7395728 print_time=3678.991 buffer_time=2.266 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Stats 3655.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20780915 bytes_read=2795792 bytes_retransmit=9 bytes_invalid=0 send_seq=370461 receive_seq=370461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=0 freq=400016106 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22918 bytes_read=72595 bytes_retransmit=0 bytes_invalid=0 send_seq=3791 receive_seq=3791 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999219 adj=49997065 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=132051 bytes_read=3988707 bytes_retransmit=9 bytes_invalid=0 send_seq=17792 receive_seq=17792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997516 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74556 bytes_read=1550523 bytes_retransmit=9 bytes_invalid=0 send_seq=9667 receive_seq=9667 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997347 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23185 bytes_read=930874 bytes_retransmit=9 bytes_invalid=0 send_seq=3805 receive_seq=3805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997509 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23671 bytes_read=71174 bytes_retransmit=9 bytes_invalid=0 send_seq=3792 receive_seq=3792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999410 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77763 bytes_read=1529633 bytes_retransmit=0 bytes_invalid=0 send_seq=8351 receive_seq=8351 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998655 coil_temp=17.3 refs=0 mcu_temp=20.56 supply_voltage=3.012 th0: temp=46.9 th1: temp=45.4 th2: temp=50.5 th3: temp=48.6 sysload=0.28 cputime=282.170 memavail=7395728 print_time=3679.639 buffer_time=1.914 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3656.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20781267 bytes_read=2796217 bytes_retransmit=9 bytes_invalid=0 send_seq=370484 receive_seq=370484 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016107 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22924 bytes_read=72611 bytes_retransmit=0 bytes_invalid=0 send_seq=3792 receive_seq=3792 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999218 adj=49997077 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=132127 bytes_read=3991782 bytes_retransmit=9 bytes_invalid=0 send_seq=17803 receive_seq=17803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997551 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74562 bytes_read=1550623 bytes_retransmit=9 bytes_invalid=0 send_seq=9668 receive_seq=9668 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997397 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23191 bytes_read=931108 bytes_retransmit=9 bytes_invalid=0 send_seq=3806 receive_seq=3806 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997527 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23677 bytes_read=71190 bytes_retransmit=9 bytes_invalid=0 send_seq=3793 receive_seq=3793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999414 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77769 bytes_read=1529989 bytes_retransmit=0 bytes_invalid=0 send_seq=8352 receive_seq=8352 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998664 coil_temp=17.3 refs=0 mcu_temp=20.56 supply_voltage=3.012 th0: temp=46.8 th1: temp=45.7 th2: temp=50.5 th3: temp=48.6 sysload=0.28 cputime=282.231 memavail=7395404 print_time=3679.639 buffer_time=0.914 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Writing raw accelerometer data to /tmp/raw_data_x_toolboard_t0_t0.csv file
RatOS | IDEX:: Selecting T1..
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 20.000000
RatOS | IDEX:: Toolhead offset applied for T1: X=-0.0 Y=-0.0 Z=-0.0
Activating extruder extruder1
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
Probing point (557.600, 250.000, 20.000)
Stats 3657.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20783465 bytes_read=2796826 bytes_retransmit=9 bytes_invalid=0 send_seq=370538 receive_seq=370538 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=35 upcoming_bytes=0 freq=400016103 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22930 bytes_read=72627 bytes_retransmit=0 bytes_invalid=0 send_seq=3793 receive_seq=3793 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999218 adj=49997067 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=132196 bytes_read=3995018 bytes_retransmit=9 bytes_invalid=0 send_seq=17813 receive_seq=17813 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997644 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74568 bytes_read=1550751 bytes_retransmit=9 bytes_invalid=0 send_seq=9669 receive_seq=9669 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997393 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23197 bytes_read=931417 bytes_retransmit=9 bytes_invalid=0 send_seq=3807 receive_seq=3807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997519 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23683 bytes_read=71217 bytes_retransmit=9 bytes_invalid=0 send_seq=3794 receive_seq=3794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999414 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77775 bytes_read=1530361 bytes_retransmit=0 bytes_invalid=0 send_seq=8353 receive_seq=8353 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998656 coil_temp=17.3 refs=0 mcu_temp=20.55 supply_voltage=3.012 th0: temp=46.8 th1: temp=45.7 th2: temp=50.8 th3: temp=48.5 sysload=0.28 cputime=282.385 memavail=7380908 print_time=3680.917 buffer_time=1.141 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
LIS2DW finished 'toolboard_t0' measurements
Stats 3658.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20783798 bytes_read=2797251 bytes_retransmit=9 bytes_invalid=0 send_seq=370561 receive_seq=370561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016107 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22936 bytes_read=72656 bytes_retransmit=0 bytes_invalid=0 send_seq=3794 receive_seq=3794 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999221 adj=49997081 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=132257 bytes_read=3995244 bytes_retransmit=9 bytes_invalid=0 send_seq=17820 receive_seq=17820 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997638 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74574 bytes_read=1550865 bytes_retransmit=9 bytes_invalid=0 send_seq=9670 receive_seq=9670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997412 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23203 bytes_read=931651 bytes_retransmit=9 bytes_invalid=0 send_seq=3808 receive_seq=3808 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997538 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23689 bytes_read=71233 bytes_retransmit=9 bytes_invalid=0 send_seq=3795 receive_seq=3795 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999415 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=30.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77781 bytes_read=1530717 bytes_retransmit=0 bytes_invalid=0 send_seq=8354 receive_seq=8354 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998647 coil_temp=17.3 refs=0 mcu_temp=20.55 supply_voltage=3.012 th0: temp=46.9 th1: temp=45.6 th2: temp=50.7 th3: temp=48.7 sysload=0.26 cputime=282.459 memavail=7395952 print_time=3680.917 buffer_time=0.140 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t1' measurements
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t0' measurements
toolhead: max_velocity: 600.000000
max_accel: 8379.841000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance testing
Testing frequency 10 Hz
Testing frequency 11 Hz
Testing frequency 12 Hz
Stats 3659.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20793156 bytes_read=2798421 bytes_retransmit=9 bytes_invalid=0 send_seq=370733 receive_seq=370733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=169 freq=400016082 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22942 bytes_read=72672 bytes_retransmit=0 bytes_invalid=0 send_seq=3795 receive_seq=3795 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999220 adj=49997128 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=132419 bytes_read=3997731 bytes_retransmit=9 bytes_invalid=0 send_seq=17839 receive_seq=17839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997627 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74736 bytes_read=1553352 bytes_retransmit=9 bytes_invalid=0 send_seq=9689 receive_seq=9689 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997471 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23209 bytes_read=931885 bytes_retransmit=9 bytes_invalid=0 send_seq=3809 receive_seq=3809 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997552 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23695 bytes_read=71249 bytes_retransmit=9 bytes_invalid=0 send_seq=3796 receive_seq=3796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999419 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77787 bytes_read=1531073 bytes_retransmit=0 bytes_invalid=0 send_seq=8355 receive_seq=8355 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998651 coil_temp=17.3 refs=0 mcu_temp=20.54 supply_voltage=3.012 th0: temp=46.9 th1: temp=46.1 th2: temp=50.7 th3: temp=48.6 sysload=0.26 cputime=282.738 memavail=7395700 print_time=3684.105 buffer_time=2.328 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 13 Hz
Stats 3660.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20797000 bytes_read=2799168 bytes_retransmit=9 bytes_invalid=0 send_seq=370812 receive_seq=370812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=0 freq=400016104 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22948 bytes_read=72688 bytes_retransmit=0 bytes_invalid=0 send_seq=3796 receive_seq=3796 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999219 adj=49997217 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=132495 bytes_read=4000759 bytes_retransmit=9 bytes_invalid=0 send_seq=17850 receive_seq=17850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997712 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74812 bytes_read=1556380 bytes_retransmit=9 bytes_invalid=0 send_seq=9700 receive_seq=9700 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997597 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23215 bytes_read=932179 bytes_retransmit=9 bytes_invalid=0 send_seq=3810 receive_seq=3810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23701 bytes_read=71265 bytes_retransmit=9 bytes_invalid=0 send_seq=3797 receive_seq=3797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999445 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77793 bytes_read=1531429 bytes_retransmit=0 bytes_invalid=0 send_seq=8356 receive_seq=8356 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998676 coil_temp=17.3 refs=0 mcu_temp=20.54 supply_voltage=3.012 th0: temp=46.9 th1: temp=45.9 th2: temp=50.7 th3: temp=48.6 sysload=0.26 cputime=282.837 memavail=7395700 print_time=3684.948 buffer_time=2.170 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 14 Hz
Stats 3661.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20801217 bytes_read=2799900 bytes_retransmit=9 bytes_invalid=0 send_seq=370897 receive_seq=370897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=35 upcoming_bytes=713 freq=400016105 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22954 bytes_read=72704 bytes_retransmit=0 bytes_invalid=0 send_seq=3797 receive_seq=3797 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999219 adj=49997170 toolboard_t0: mcu_awake=0.242 mcu_task_avg=0.000115 mcu_task_stddev=0.000070 bytes_write=132571 bytes_read=4003822 bytes_retransmit=9 bytes_invalid=0 send_seq=17861 receive_seq=17861 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997651 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74888 bytes_read=1559425 bytes_retransmit=9 bytes_invalid=0 send_seq=9711 receive_seq=9711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23221 bytes_read=932413 bytes_retransmit=9 bytes_invalid=0 send_seq=3811 receive_seq=3811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23707 bytes_read=71281 bytes_retransmit=9 bytes_invalid=0 send_seq=3798 receive_seq=3798 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77799 bytes_read=1531769 bytes_retransmit=0 bytes_invalid=0 send_seq=8357 receive_seq=8357 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998653 coil_temp=17.3 refs=0 mcu_temp=20.54 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.7 th2: temp=50.7 th3: temp=48.6 sysload=0.26 cputime=282.939 memavail=7395700 print_time=3685.970 buffer_time=2.193 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 15 Hz
Stats 3662.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20805954 bytes_read=2800680 bytes_retransmit=9 bytes_invalid=0 send_seq=370991 receive_seq=370991 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400016089 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=22960 bytes_read=72720 bytes_retransmit=0 bytes_invalid=0 send_seq=3798 receive_seq=3798 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999218 adj=49997179 toolboard_t0: mcu_awake=0.242 mcu_task_avg=0.000115 mcu_task_stddev=0.000070 bytes_write=132647 bytes_read=4006879 bytes_retransmit=9 bytes_invalid=0 send_seq=17872 receive_seq=17872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997656 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=74964 bytes_read=1562481 bytes_retransmit=9 bytes_invalid=0 send_seq=9722 receive_seq=9722 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23227 bytes_read=932662 bytes_retransmit=9 bytes_invalid=0 send_seq=3812 receive_seq=3812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23713 bytes_read=71308 bytes_retransmit=9 bytes_invalid=0 send_seq=3799 receive_seq=3799 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77805 bytes_read=1532125 bytes_retransmit=0 bytes_invalid=0 send_seq=8358 receive_seq=8358 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998647 coil_temp=17.3 refs=0 mcu_temp=20.54 supply_voltage=3.012 th0: temp=46.6 th1: temp=45.9 th2: temp=50.7 th3: temp=48.6 sysload=0.26 cputime=283.042 memavail=7395700 print_time=3686.825 buffer_time=2.046 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 16 Hz
Stats 3663.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20810567 bytes_read=2801480 bytes_retransmit=9 bytes_invalid=0 send_seq=371081 receive_seq=371081 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=563 freq=400016050 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22972 bytes_read=72765 bytes_retransmit=0 bytes_invalid=0 send_seq=3800 receive_seq=3800 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49997195 toolboard_t0: mcu_awake=0.242 mcu_task_avg=0.000115 mcu_task_stddev=0.000070 bytes_write=132722 bytes_read=4009957 bytes_retransmit=9 bytes_invalid=0 send_seq=17883 receive_seq=17883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997675 toolboard_t1: mcu_awake=0.258 mcu_task_avg=0.000117 mcu_task_stddev=0.000070 bytes_write=75039 bytes_read=1565576 bytes_retransmit=9 bytes_invalid=0 send_seq=9733 receive_seq=9733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23239 bytes_read=932972 bytes_retransmit=9 bytes_invalid=0 send_seq=3814 receive_seq=3814 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23725 bytes_read=71340 bytes_retransmit=9 bytes_invalid=0 send_seq=3801 receive_seq=3801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999485 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77817 bytes_read=1532497 bytes_retransmit=0 bytes_invalid=0 send_seq=8360 receive_seq=8360 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998678 coil_temp=17.3 refs=0 mcu_temp=20.54 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.0 th2: temp=50.6 th3: temp=48.4 sysload=0.40 cputime=283.158 memavail=7395464 print_time=3687.790 buffer_time=2.011 print_stall=0 extruder: target=0 temp=19.8 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 17 Hz
Stats 3664.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20815424 bytes_read=2802255 bytes_retransmit=9 bytes_invalid=0 send_seq=371174 receive_seq=371174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=1960 freq=400016046 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22978 bytes_read=72781 bytes_retransmit=0 bytes_invalid=0 send_seq=3801 receive_seq=3801 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997247 toolboard_t0: mcu_awake=0.242 mcu_task_avg=0.000115 mcu_task_stddev=0.000070 bytes_write=132798 bytes_read=4013014 bytes_retransmit=9 bytes_invalid=0 send_seq=17894 receive_seq=17894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997723 toolboard_t1: mcu_awake=0.258 mcu_task_avg=0.000117 mcu_task_stddev=0.000070 bytes_write=75115 bytes_read=1568692 bytes_retransmit=9 bytes_invalid=0 send_seq=9744 receive_seq=9744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997684 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23245 bytes_read=933206 bytes_retransmit=9 bytes_invalid=0 send_seq=3815 receive_seq=3815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997700 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23731 bytes_read=71356 bytes_retransmit=9 bytes_invalid=0 send_seq=3802 receive_seq=3802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999485 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77823 bytes_read=1532853 bytes_retransmit=0 bytes_invalid=0 send_seq=8361 receive_seq=8361 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998691 coil_temp=17.3 refs=0 mcu_temp=20.54 supply_voltage=3.012 th0: temp=46.8 th1: temp=45.8 th2: temp=50.8 th3: temp=48.4 sysload=0.40 cputime=283.281 memavail=7395952 print_time=3688.993 buffer_time=2.213 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 18 Hz
Stats 3665.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20820760 bytes_read=2803086 bytes_retransmit=9 bytes_invalid=0 send_seq=371275 receive_seq=371275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=1272 freq=400016030 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22984 bytes_read=72797 bytes_retransmit=0 bytes_invalid=0 send_seq=3802 receive_seq=3802 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999214 adj=49997230 toolboard_t0: mcu_awake=0.242 mcu_task_avg=0.000115 mcu_task_stddev=0.000070 bytes_write=132874 bytes_read=4016071 bytes_retransmit=9 bytes_invalid=0 send_seq=17905 receive_seq=17905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997693 toolboard_t1: mcu_awake=0.258 mcu_task_avg=0.000117 mcu_task_stddev=0.000070 bytes_write=75191 bytes_read=1571751 bytes_retransmit=9 bytes_invalid=0 send_seq=9755 receive_seq=9755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997708 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23251 bytes_read=933440 bytes_retransmit=9 bytes_invalid=0 send_seq=3816 receive_seq=3816 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997709 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23737 bytes_read=71372 bytes_retransmit=9 bytes_invalid=0 send_seq=3803 receive_seq=3803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999468 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77829 bytes_read=1533209 bytes_retransmit=0 bytes_invalid=0 send_seq=8362 receive_seq=8362 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998676 coil_temp=17.3 refs=0 mcu_temp=20.54 supply_voltage=3.012 th0: temp=46.8 th1: temp=45.8 th2: temp=50.7 th3: temp=48.5 sysload=0.40 cputime=283.390 memavail=7395744 print_time=3689.940 buffer_time=2.159 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 19 Hz
Stats 3666.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20825875 bytes_read=2803905 bytes_retransmit=9 bytes_invalid=0 send_seq=371371 receive_seq=371371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=2908 freq=400016081 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22990 bytes_read=72813 bytes_retransmit=0 bytes_invalid=0 send_seq=3803 receive_seq=3803 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997246 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=132950 bytes_read=4019230 bytes_retransmit=9 bytes_invalid=0 send_seq=17916 receive_seq=17916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997701 toolboard_t1: mcu_awake=0.258 mcu_task_avg=0.000117 mcu_task_stddev=0.000070 bytes_write=75267 bytes_read=1574837 bytes_retransmit=9 bytes_invalid=0 send_seq=9766 receive_seq=9766 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997682 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23257 bytes_read=933734 bytes_retransmit=9 bytes_invalid=0 send_seq=3817 receive_seq=3817 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997710 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23743 bytes_read=71388 bytes_retransmit=9 bytes_invalid=0 send_seq=3804 receive_seq=3804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999475 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77835 bytes_read=1533565 bytes_retransmit=0 bytes_invalid=0 send_seq=8363 receive_seq=8363 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998673 coil_temp=17.3 refs=0 mcu_temp=20.53 supply_voltage=3.012 th0: temp=46.8 th1: temp=46.1 th2: temp=50.7 th3: temp=48.5 sysload=0.40 cputime=283.507 memavail=7394988 print_time=3691.151 buffer_time=2.369 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 20 Hz
Stats 3667.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20831139 bytes_read=2804700 bytes_retransmit=9 bytes_invalid=0 send_seq=371468 receive_seq=371468 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=3388 freq=400016058 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=22996 bytes_read=72829 bytes_retransmit=0 bytes_invalid=0 send_seq=3804 receive_seq=3804 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997152 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133026 bytes_read=4022285 bytes_retransmit=9 bytes_invalid=0 send_seq=17927 receive_seq=17927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997585 toolboard_t1: mcu_awake=0.258 mcu_task_avg=0.000117 mcu_task_stddev=0.000070 bytes_write=75343 bytes_read=1577889 bytes_retransmit=9 bytes_invalid=0 send_seq=9777 receive_seq=9777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997515 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23263 bytes_read=933983 bytes_retransmit=9 bytes_invalid=0 send_seq=3818 receive_seq=3818 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23749 bytes_read=71415 bytes_retransmit=9 bytes_invalid=0 send_seq=3805 receive_seq=3805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999444 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77841 bytes_read=1533921 bytes_retransmit=0 bytes_invalid=0 send_seq=8364 receive_seq=8364 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998617 coil_temp=17.3 refs=0 mcu_temp=20.53 supply_voltage=3.012 th0: temp=46.8 th1: temp=45.9 th2: temp=50.8 th3: temp=48.3 sysload=0.40 cputime=283.623 memavail=7396708 print_time=3692.021 buffer_time=2.239 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 21 Hz
Stats 3668.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20837288 bytes_read=2805585 bytes_retransmit=9 bytes_invalid=0 send_seq=371583 receive_seq=371583 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=2584 freq=400016041 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23002 bytes_read=72858 bytes_retransmit=0 bytes_invalid=0 send_seq=3805 receive_seq=3805 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997188 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133102 bytes_read=4025325 bytes_retransmit=9 bytes_invalid=0 send_seq=17938 receive_seq=17938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997623 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=75419 bytes_read=1580945 bytes_retransmit=9 bytes_invalid=0 send_seq=9788 receive_seq=9788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997533 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23269 bytes_read=934217 bytes_retransmit=9 bytes_invalid=0 send_seq=3819 receive_seq=3819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23755 bytes_read=71431 bytes_retransmit=9 bytes_invalid=0 send_seq=3806 receive_seq=3806 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77847 bytes_read=1534277 bytes_retransmit=0 bytes_invalid=0 send_seq=8365 receive_seq=8365 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998639 coil_temp=17.3 refs=0 mcu_temp=20.53 supply_voltage=3.012 th0: temp=46.6 th1: temp=45.9 th2: temp=50.5 th3: temp=48.4 sysload=0.53 cputime=283.739 memavail=7396488 print_time=3692.985 buffer_time=2.202 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 22 Hz
Stats 3669.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=20843108 bytes_read=2806459 bytes_retransmit=9 bytes_invalid=0 send_seq=371690 receive_seq=371690 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=2620 freq=400016026 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23008 bytes_read=72874 bytes_retransmit=0 bytes_invalid=0 send_seq=3806 receive_seq=3806 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997204 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133178 bytes_read=4028390 bytes_retransmit=9 bytes_invalid=0 send_seq=17949 receive_seq=17949 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997649 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=75495 bytes_read=1584010 bytes_retransmit=9 bytes_invalid=0 send_seq=9799 receive_seq=9799 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997543 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23275 bytes_read=934511 bytes_retransmit=9 bytes_invalid=0 send_seq=3820 receive_seq=3820 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997669 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23761 bytes_read=71447 bytes_retransmit=9 bytes_invalid=0 send_seq=3807 receive_seq=3807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77853 bytes_read=1534633 bytes_retransmit=0 bytes_invalid=0 send_seq=8366 receive_seq=8366 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998671 coil_temp=17.3 refs=0 mcu_temp=20.51 supply_voltage=3.012 th0: temp=46.8 th1: temp=45.6 th2: temp=50.4 th3: temp=48.4 sysload=0.53 cputime=283.858 memavail=7396496 print_time=3693.840 buffer_time=2.056 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 23 Hz
Stats 3670.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=20848827 bytes_read=2807320 bytes_retransmit=9 bytes_invalid=0 send_seq=371797 receive_seq=371797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=4369 freq=400016009 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23014 bytes_read=72890 bytes_retransmit=0 bytes_invalid=0 send_seq=3807 receive_seq=3807 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997235 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133254 bytes_read=4031430 bytes_retransmit=9 bytes_invalid=0 send_seq=17960 receive_seq=17960 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997673 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=75571 bytes_read=1587049 bytes_retransmit=9 bytes_invalid=0 send_seq=9810 receive_seq=9810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997552 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23281 bytes_read=934745 bytes_retransmit=9 bytes_invalid=0 send_seq=3821 receive_seq=3821 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997781 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23767 bytes_read=71463 bytes_retransmit=9 bytes_invalid=0 send_seq=3808 receive_seq=3808 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77859 bytes_read=1534989 bytes_retransmit=0 bytes_invalid=0 send_seq=8367 receive_seq=8367 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998683 coil_temp=17.3 refs=0 mcu_temp=20.51 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.1 th2: temp=50.2 th3: temp=48.1 sysload=0.53 cputime=283.983 memavail=7396496 print_time=3695.031 buffer_time=2.246 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 24 Hz
Stats 3671.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=20855314 bytes_read=2808230 bytes_retransmit=9 bytes_invalid=0 send_seq=371918 receive_seq=371918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=3556 freq=400015997 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23020 bytes_read=72906 bytes_retransmit=0 bytes_invalid=0 send_seq=3808 receive_seq=3808 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997261 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133330 bytes_read=4034486 bytes_retransmit=9 bytes_invalid=0 send_seq=17971 receive_seq=17971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997724 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=75647 bytes_read=1590147 bytes_retransmit=9 bytes_invalid=0 send_seq=9821 receive_seq=9821 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000074 adj=63997552 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23287 bytes_read=934979 bytes_retransmit=9 bytes_invalid=0 send_seq=3822 receive_seq=3822 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997748 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23773 bytes_read=71479 bytes_retransmit=9 bytes_invalid=0 send_seq=3809 receive_seq=3809 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77865 bytes_read=1535345 bytes_retransmit=0 bytes_invalid=0 send_seq=8368 receive_seq=8368 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998697 coil_temp=17.3 refs=0 mcu_temp=20.51 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.1 th2: temp=50.6 th3: temp=48.2 sysload=0.53 cputime=284.097 memavail=7396496 print_time=3695.994 buffer_time=2.208 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 25 Hz
Stats 3672.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=20861714 bytes_read=2809152 bytes_retransmit=9 bytes_invalid=0 send_seq=372035 receive_seq=372035 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=3680 freq=400015985 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23026 bytes_read=72922 bytes_retransmit=0 bytes_invalid=0 send_seq=3809 receive_seq=3809 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999214 adj=49997271 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133406 bytes_read=4037628 bytes_retransmit=9 bytes_invalid=0 send_seq=17982 receive_seq=17982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997748 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=75723 bytes_read=1593231 bytes_retransmit=9 bytes_invalid=0 send_seq=9832 receive_seq=9832 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997742 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23293 bytes_read=935288 bytes_retransmit=9 bytes_invalid=0 send_seq=3823 receive_seq=3823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997736 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23779 bytes_read=71506 bytes_retransmit=9 bytes_invalid=0 send_seq=3810 receive_seq=3810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77871 bytes_read=1535701 bytes_retransmit=0 bytes_invalid=0 send_seq=8369 receive_seq=8369 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998699 coil_temp=17.3 refs=0 mcu_temp=20.51 supply_voltage=3.012 th0: temp=46.6 th1: temp=45.8 th2: temp=50.2 th3: temp=48.2 sysload=0.53 cputime=284.210 memavail=7396496 print_time=3696.871 buffer_time=2.084 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 26 Hz
Stats 3673.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=20867839 bytes_read=2810032 bytes_retransmit=9 bytes_invalid=0 send_seq=372149 receive_seq=372149 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=3903 freq=400015973 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23032 bytes_read=72951 bytes_retransmit=0 bytes_invalid=0 send_seq=3810 receive_seq=3810 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997294 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133482 bytes_read=4040685 bytes_retransmit=9 bytes_invalid=0 send_seq=17993 receive_seq=17993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997754 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=75799 bytes_read=1596304 bytes_retransmit=9 bytes_invalid=0 send_seq=9843 receive_seq=9843 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997713 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23299 bytes_read=935522 bytes_retransmit=9 bytes_invalid=0 send_seq=3824 receive_seq=3824 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997734 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23785 bytes_read=71522 bytes_retransmit=9 bytes_invalid=0 send_seq=3811 receive_seq=3811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77877 bytes_read=1536057 bytes_retransmit=0 bytes_invalid=0 send_seq=8370 receive_seq=8370 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998749 coil_temp=17.3 refs=0 mcu_temp=20.50 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.9 th2: temp=50.2 th3: temp=48.1 sysload=0.48 cputime=284.323 memavail=7396496 print_time=3697.838 buffer_time=2.051 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 27 Hz
Stats 3674.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=20874963 bytes_read=2810987 bytes_retransmit=9 bytes_invalid=0 send_seq=372278 receive_seq=372278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=5008 freq=400015980 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23038 bytes_read=72967 bytes_retransmit=0 bytes_invalid=0 send_seq=3811 receive_seq=3811 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997288 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133558 bytes_read=4043741 bytes_retransmit=9 bytes_invalid=0 send_seq=18004 receive_seq=18004 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997853 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=75875 bytes_read=1599360 bytes_retransmit=9 bytes_invalid=0 send_seq=9854 receive_seq=9854 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997676 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23305 bytes_read=935756 bytes_retransmit=9 bytes_invalid=0 send_seq=3825 receive_seq=3825 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997721 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23791 bytes_read=71538 bytes_retransmit=9 bytes_invalid=0 send_seq=3812 receive_seq=3812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77883 bytes_read=1536413 bytes_retransmit=0 bytes_invalid=0 send_seq=8371 receive_seq=8371 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998733 coil_temp=17.3 refs=0 mcu_temp=20.49 supply_voltage=3.012 th0: temp=46.8 th1: temp=45.9 th2: temp=50.2 th3: temp=48.0 sysload=0.48 cputime=284.444 memavail=7396496 print_time=3699.046 buffer_time=2.260 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 28 Hz
Stats 3675.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=20881752 bytes_read=2811972 bytes_retransmit=9 bytes_invalid=0 send_seq=372404 receive_seq=372404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=4384 freq=400015972 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23044 bytes_read=72983 bytes_retransmit=0 bytes_invalid=0 send_seq=3812 receive_seq=3812 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997254 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133634 bytes_read=4046829 bytes_retransmit=9 bytes_invalid=0 send_seq=18015 receive_seq=18015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997766 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=75951 bytes_read=1602444 bytes_retransmit=9 bytes_invalid=0 send_seq=9865 receive_seq=9865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997594 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23311 bytes_read=936050 bytes_retransmit=9 bytes_invalid=0 send_seq=3826 receive_seq=3826 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23797 bytes_read=71554 bytes_retransmit=9 bytes_invalid=0 send_seq=3813 receive_seq=3813 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77889 bytes_read=1536769 bytes_retransmit=0 bytes_invalid=0 send_seq=8372 receive_seq=8372 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998701 coil_temp=17.3 refs=0 mcu_temp=20.49 supply_voltage=3.012 th0: temp=46.9 th1: temp=45.9 th2: temp=50.1 th3: temp=48.1 sysload=0.48 cputime=284.557 memavail=7396496 print_time=3699.921 buffer_time=2.134 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 29 Hz
Stats 3676.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=20888243 bytes_read=2812887 bytes_retransmit=9 bytes_invalid=0 send_seq=372525 receive_seq=372525 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=4584 freq=400015958 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23050 bytes_read=72999 bytes_retransmit=0 bytes_invalid=0 send_seq=3813 receive_seq=3813 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997268 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133703 bytes_read=4049879 bytes_retransmit=9 bytes_invalid=0 send_seq=18025 receive_seq=18025 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997755 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=76020 bytes_read=1605480 bytes_retransmit=9 bytes_invalid=0 send_seq=9875 receive_seq=9875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997577 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23317 bytes_read=936284 bytes_retransmit=9 bytes_invalid=0 send_seq=3827 receive_seq=3827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23803 bytes_read=71570 bytes_retransmit=9 bytes_invalid=0 send_seq=3814 receive_seq=3814 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77895 bytes_read=1537125 bytes_retransmit=0 bytes_invalid=0 send_seq=8373 receive_seq=8373 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998703 coil_temp=17.3 refs=0 mcu_temp=20.50 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.0 th2: temp=49.8 th3: temp=47.9 sysload=0.48 cputime=284.668 memavail=7397480 print_time=3700.847 buffer_time=2.059 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 30 Hz
Stats 3677.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=20895661 bytes_read=2813872 bytes_retransmit=9 bytes_invalid=0 send_seq=372660 receive_seq=372660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=6056 freq=400015956 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23056 bytes_read=73015 bytes_retransmit=0 bytes_invalid=0 send_seq=3814 receive_seq=3814 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997290 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133779 bytes_read=4052936 bytes_retransmit=9 bytes_invalid=0 send_seq=18036 receive_seq=18036 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997756 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=76096 bytes_read=1608538 bytes_retransmit=9 bytes_invalid=0 send_seq=9886 receive_seq=9886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997668 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23323 bytes_read=936533 bytes_retransmit=9 bytes_invalid=0 send_seq=3828 receive_seq=3828 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23809 bytes_read=71597 bytes_retransmit=9 bytes_invalid=0 send_seq=3815 receive_seq=3815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77901 bytes_read=1537481 bytes_retransmit=0 bytes_invalid=0 send_seq=8374 receive_seq=8374 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998700 coil_temp=17.3 refs=0 mcu_temp=20.50 supply_voltage=3.012 th0: temp=46.8 th1: temp=46.2 th2: temp=50.2 th3: temp=48.0 sysload=0.48 cputime=284.795 memavail=7397496 print_time=3702.068 buffer_time=2.279 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 31 Hz
Stats 3678.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=20902727 bytes_read=2814861 bytes_retransmit=9 bytes_invalid=0 send_seq=372790 receive_seq=372790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=5279 freq=400015948 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23062 bytes_read=73031 bytes_retransmit=0 bytes_invalid=0 send_seq=3815 receive_seq=3815 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997261 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133855 bytes_read=4056021 bytes_retransmit=9 bytes_invalid=0 send_seq=18047 receive_seq=18047 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997715 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=76172 bytes_read=1611641 bytes_retransmit=9 bytes_invalid=0 send_seq=9897 receive_seq=9897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997593 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23329 bytes_read=936827 bytes_retransmit=9 bytes_invalid=0 send_seq=3829 receive_seq=3829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23815 bytes_read=71613 bytes_retransmit=9 bytes_invalid=0 send_seq=3816 receive_seq=3816 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999445 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77907 bytes_read=1537837 bytes_retransmit=0 bytes_invalid=0 send_seq=8375 receive_seq=8375 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998680 coil_temp=17.3 refs=0 mcu_temp=20.49 supply_voltage=3.012 th0: temp=46.8 th1: temp=45.9 th2: temp=50.2 th3: temp=48.1 sysload=0.60 cputime=284.909 memavail=7397496 print_time=3702.930 buffer_time=2.140 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 32 Hz
Stats 3679.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=20909477 bytes_read=2815791 bytes_retransmit=9 bytes_invalid=0 send_seq=372914 receive_seq=372914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=5775 freq=400015950 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23068 bytes_read=73060 bytes_retransmit=0 bytes_invalid=0 send_seq=3816 receive_seq=3816 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997266 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133931 bytes_read=4059077 bytes_retransmit=9 bytes_invalid=0 send_seq=18058 receive_seq=18058 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997719 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=76248 bytes_read=1614760 bytes_retransmit=9 bytes_invalid=0 send_seq=9908 receive_seq=9908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000081 adj=63997579 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23335 bytes_read=937061 bytes_retransmit=9 bytes_invalid=0 send_seq=3830 receive_seq=3830 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23821 bytes_read=71629 bytes_retransmit=9 bytes_invalid=0 send_seq=3817 receive_seq=3817 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999444 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77913 bytes_read=1538193 bytes_retransmit=0 bytes_invalid=0 send_seq=8376 receive_seq=8376 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998682 coil_temp=17.3 refs=0 mcu_temp=20.47 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.9 th2: temp=49.9 th3: temp=47.7 sysload=0.60 cputime=285.022 memavail=7397496 print_time=3703.870 buffer_time=2.079 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 33 Hz
Stats 3680.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=20917623 bytes_read=2816852 bytes_retransmit=9 bytes_invalid=0 send_seq=373061 receive_seq=373061 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=7312 freq=400015941 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23074 bytes_read=73076 bytes_retransmit=0 bytes_invalid=0 send_seq=3817 receive_seq=3817 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997270 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134007 bytes_read=4062192 bytes_retransmit=9 bytes_invalid=0 send_seq=18069 receive_seq=18069 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997700 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=76324 bytes_read=1617818 bytes_retransmit=9 bytes_invalid=0 send_seq=9919 receive_seq=9919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000078 adj=63997748 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23341 bytes_read=937295 bytes_retransmit=9 bytes_invalid=0 send_seq=3831 receive_seq=3831 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23827 bytes_read=71645 bytes_retransmit=9 bytes_invalid=0 send_seq=3818 receive_seq=3818 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77919 bytes_read=1538549 bytes_retransmit=0 bytes_invalid=0 send_seq=8377 receive_seq=8377 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998672 coil_temp=17.3 refs=0 mcu_temp=20.47 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.2 th2: temp=50.0 th3: temp=48.1 sysload=0.60 cputime=285.147 memavail=7397496 print_time=3705.115 buffer_time=2.323 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 34 Hz
Stats 3681.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=20925008 bytes_read=2817866 bytes_retransmit=9 bytes_invalid=0 send_seq=373196 receive_seq=373196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=6263 freq=400015929 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23080 bytes_read=73092 bytes_retransmit=0 bytes_invalid=0 send_seq=3818 receive_seq=3818 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997257 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134083 bytes_read=4065295 bytes_retransmit=9 bytes_invalid=0 send_seq=18080 receive_seq=18080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997691 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=76400 bytes_read=1620905 bytes_retransmit=9 bytes_invalid=0 send_seq=9930 receive_seq=9930 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000076 adj=63997662 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23347 bytes_read=937589 bytes_retransmit=9 bytes_invalid=0 send_seq=3832 receive_seq=3832 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23833 bytes_read=71661 bytes_retransmit=9 bytes_invalid=0 send_seq=3819 receive_seq=3819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77925 bytes_read=1538905 bytes_retransmit=0 bytes_invalid=0 send_seq=8378 receive_seq=8378 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998674 coil_temp=17.3 refs=0 mcu_temp=20.47 supply_voltage=3.012 th0: temp=46.8 th1: temp=46.1 th2: temp=49.9 th3: temp=48.0 sysload=0.60 cputime=285.265 memavail=7397496 print_time=3705.988 buffer_time=2.196 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 35 Hz
Stats 3682.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=20932166 bytes_read=2818821 bytes_retransmit=9 bytes_invalid=0 send_seq=373326 receive_seq=373326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=7216 freq=400015925 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23086 bytes_read=73108 bytes_retransmit=0 bytes_invalid=0 send_seq=3819 receive_seq=3819 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997277 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134159 bytes_read=4068353 bytes_retransmit=9 bytes_invalid=0 send_seq=18091 receive_seq=18091 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997707 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=76476 bytes_read=1623961 bytes_retransmit=9 bytes_invalid=0 send_seq=9941 receive_seq=9941 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997645 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23353 bytes_read=937838 bytes_retransmit=9 bytes_invalid=0 send_seq=3833 receive_seq=3833 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23839 bytes_read=71688 bytes_retransmit=9 bytes_invalid=0 send_seq=3820 receive_seq=3820 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77931 bytes_read=1539261 bytes_retransmit=0 bytes_invalid=0 send_seq=8379 receive_seq=8379 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998678 coil_temp=17.3 refs=0 mcu_temp=20.47 supply_voltage=3.012 th0: temp=46.6 th1: temp=46.1 th2: temp=49.9 th3: temp=47.8 sysload=0.60 cputime=285.385 memavail=7397032 print_time=3706.917 buffer_time=2.125 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 36 Hz
Stats 3683.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=20940583 bytes_read=2819881 bytes_retransmit=9 bytes_invalid=0 send_seq=373476 receive_seq=373476 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=5408 freq=400015925 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23092 bytes_read=73124 bytes_retransmit=0 bytes_invalid=0 send_seq=3820 receive_seq=3820 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997268 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134235 bytes_read=4071410 bytes_retransmit=9 bytes_invalid=0 send_seq=18102 receive_seq=18102 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997708 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=76552 bytes_read=1627037 bytes_retransmit=9 bytes_invalid=0 send_seq=9952 receive_seq=9952 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997600 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23359 bytes_read=938072 bytes_retransmit=9 bytes_invalid=0 send_seq=3834 receive_seq=3834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997730 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23845 bytes_read=71704 bytes_retransmit=9 bytes_invalid=0 send_seq=3821 receive_seq=3821 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999455 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77937 bytes_read=1539617 bytes_retransmit=0 bytes_invalid=0 send_seq=8380 receive_seq=8380 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998672 coil_temp=17.3 refs=0 mcu_temp=20.46 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.4 th2: temp=50.1 th3: temp=47.9 sysload=0.64 cputime=285.510 memavail=7397032 print_time=3707.795 buffer_time=2.003 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 37 Hz
Stats 3684.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=20948512 bytes_read=2820940 bytes_retransmit=9 bytes_invalid=0 send_seq=373620 receive_seq=373620 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=35 upcoming_bytes=7431 freq=400015910 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23098 bytes_read=73153 bytes_retransmit=0 bytes_invalid=0 send_seq=3821 receive_seq=3821 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997273 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134311 bytes_read=4074494 bytes_retransmit=9 bytes_invalid=0 send_seq=18113 receive_seq=18113 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997697 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=76628 bytes_read=1630121 bytes_retransmit=9 bytes_invalid=0 send_seq=9963 receive_seq=9963 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997567 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23365 bytes_read=938366 bytes_retransmit=9 bytes_invalid=0 send_seq=3835 receive_seq=3835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997707 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23851 bytes_read=71720 bytes_retransmit=9 bytes_invalid=0 send_seq=3822 receive_seq=3822 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77943 bytes_read=1539973 bytes_retransmit=0 bytes_invalid=0 send_seq=8381 receive_seq=8381 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998675 coil_temp=17.3 refs=0 mcu_temp=20.46 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.4 th2: temp=50.0 th3: temp=48.1 sysload=0.64 cputime=285.661 memavail=7396660 print_time=3709.016 buffer_time=2.223 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 38 Hz
Stats 3685.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=20956257 bytes_read=2821966 bytes_retransmit=9 bytes_invalid=0 send_seq=373760 receive_seq=373760 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=8292 freq=400015900 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23104 bytes_read=73169 bytes_retransmit=0 bytes_invalid=0 send_seq=3822 receive_seq=3822 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997270 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134387 bytes_read=4077551 bytes_retransmit=9 bytes_invalid=0 send_seq=18124 receive_seq=18124 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997706 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=76704 bytes_read=1633177 bytes_retransmit=9 bytes_invalid=0 send_seq=9974 receive_seq=9974 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23371 bytes_read=938600 bytes_retransmit=9 bytes_invalid=0 send_seq=3836 receive_seq=3836 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997696 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23857 bytes_read=71736 bytes_retransmit=9 bytes_invalid=0 send_seq=3823 receive_seq=3823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77949 bytes_read=1540329 bytes_retransmit=0 bytes_invalid=0 send_seq=8382 receive_seq=8382 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998677 coil_temp=17.3 refs=0 mcu_temp=20.46 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.2 th2: temp=49.8 th3: temp=47.7 sysload=0.64 cputime=285.779 memavail=7396660 print_time=3709.931 buffer_time=2.137 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 39 Hz
Stats 3686.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=20965138 bytes_read=2823076 bytes_retransmit=9 bytes_invalid=0 send_seq=373920 receive_seq=373920 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=6265 freq=400015907 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23110 bytes_read=73185 bytes_retransmit=0 bytes_invalid=0 send_seq=3823 receive_seq=3823 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997274 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134463 bytes_read=4080624 bytes_retransmit=9 bytes_invalid=0 send_seq=18135 receive_seq=18135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997712 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=76780 bytes_read=1636292 bytes_retransmit=9 bytes_invalid=0 send_seq=9985 receive_seq=9985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23377 bytes_read=938834 bytes_retransmit=9 bytes_invalid=0 send_seq=3837 receive_seq=3837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23863 bytes_read=71752 bytes_retransmit=9 bytes_invalid=0 send_seq=3824 receive_seq=3824 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999457 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77955 bytes_read=1540685 bytes_retransmit=0 bytes_invalid=0 send_seq=8383 receive_seq=8383 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998687 coil_temp=17.3 refs=0 mcu_temp=20.46 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.1 th2: temp=49.8 th3: temp=47.9 sysload=0.64 cputime=285.902 memavail=7397936 print_time=3710.818 buffer_time=2.024 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 40 Hz
Stats 3687.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=20973721 bytes_read=2824180 bytes_retransmit=9 bytes_invalid=0 send_seq=374074 receive_seq=374073 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=10 upcoming_bytes=7922 freq=400016044 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23116 bytes_read=73201 bytes_retransmit=0 bytes_invalid=0 send_seq=3824 receive_seq=3824 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997246 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134539 bytes_read=4083766 bytes_retransmit=9 bytes_invalid=0 send_seq=18146 receive_seq=18146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997684 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=76856 bytes_read=1639378 bytes_retransmit=9 bytes_invalid=0 send_seq=9996 receive_seq=9996 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23383 bytes_read=939143 bytes_retransmit=9 bytes_invalid=0 send_seq=3838 receive_seq=3838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997749 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23869 bytes_read=71779 bytes_retransmit=9 bytes_invalid=0 send_seq=3825 receive_seq=3825 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77961 bytes_read=1541041 bytes_retransmit=0 bytes_invalid=0 send_seq=8384 receive_seq=8384 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998687 coil_temp=17.3 refs=0 mcu_temp=20.47 supply_voltage=3.012 th0: temp=47.0 th1: temp=45.7 th2: temp=49.9 th3: temp=48.0 sysload=0.64 cputime=286.037 memavail=7397684 print_time=3712.034 buffer_time=2.239 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 41 Hz
Stats 3688.3: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=20981602 bytes_read=2825205 bytes_retransmit=9 bytes_invalid=0 send_seq=374216 receive_seq=374216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=9275 freq=400016036 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23122 bytes_read=73217 bytes_retransmit=0 bytes_invalid=0 send_seq=3825 receive_seq=3825 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997030 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134615 bytes_read=4086825 bytes_retransmit=9 bytes_invalid=0 send_seq=18157 receive_seq=18157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997410 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=76932 bytes_read=1642452 bytes_retransmit=9 bytes_invalid=0 send_seq=10007 receive_seq=10007 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997300 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23389 bytes_read=939377 bytes_retransmit=9 bytes_invalid=0 send_seq=3839 receive_seq=3839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997539 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23875 bytes_read=71795 bytes_retransmit=9 bytes_invalid=0 send_seq=3826 receive_seq=3826 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999396 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77967 bytes_read=1541397 bytes_retransmit=0 bytes_invalid=0 send_seq=8385 receive_seq=8385 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998545 coil_temp=17.3 refs=0 mcu_temp=20.47 supply_voltage=3.012 th0: temp=46.8 th1: temp=46.2 th2: temp=50.1 th3: temp=47.8 sysload=0.59 cputime=286.156 memavail=7397684 print_time=3712.979 buffer_time=2.183 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 42 Hz
Stats 3689.3: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=20990748 bytes_read=2826335 bytes_retransmit=9 bytes_invalid=0 send_seq=374380 receive_seq=374380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=7439 freq=400016036 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23128 bytes_read=73246 bytes_retransmit=0 bytes_invalid=0 send_seq=3826 receive_seq=3826 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997065 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134684 bytes_read=4089860 bytes_retransmit=9 bytes_invalid=0 send_seq=18167 receive_seq=18167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997456 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=77001 bytes_read=1645485 bytes_retransmit=9 bytes_invalid=0 send_seq=10017 receive_seq=10017 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997316 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23395 bytes_read=939611 bytes_retransmit=9 bytes_invalid=0 send_seq=3840 receive_seq=3840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997551 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23881 bytes_read=71811 bytes_retransmit=9 bytes_invalid=0 send_seq=3827 receive_seq=3827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999402 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77973 bytes_read=1541753 bytes_retransmit=0 bytes_invalid=0 send_seq=8386 receive_seq=8386 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998595 coil_temp=17.3 refs=0 mcu_temp=20.47 supply_voltage=3.012 th0: temp=46.9 th1: temp=46.1 th2: temp=49.8 th3: temp=47.8 sysload=0.59 cputime=286.279 memavail=7397460 print_time=3713.861 buffer_time=2.065 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 43 Hz
Stats 3690.3: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=20999764 bytes_read=2827500 bytes_retransmit=9 bytes_invalid=0 send_seq=374542 receive_seq=374542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=9389 freq=400016031 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23134 bytes_read=73262 bytes_retransmit=0 bytes_invalid=0 send_seq=3827 receive_seq=3827 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997080 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134760 bytes_read=4092946 bytes_retransmit=9 bytes_invalid=0 send_seq=18178 receive_seq=18178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997480 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=77077 bytes_read=1648569 bytes_retransmit=9 bytes_invalid=0 send_seq=10028 receive_seq=10028 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997309 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23401 bytes_read=939905 bytes_retransmit=9 bytes_invalid=0 send_seq=3841 receive_seq=3841 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997544 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23887 bytes_read=71827 bytes_retransmit=9 bytes_invalid=0 send_seq=3828 receive_seq=3828 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999403 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77979 bytes_read=1542109 bytes_retransmit=0 bytes_invalid=0 send_seq=8387 receive_seq=8387 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998614 coil_temp=17.3 refs=0 mcu_temp=20.48 supply_voltage=3.012 th0: temp=46.9 th1: temp=46.3 th2: temp=50.0 th3: temp=47.9 sysload=0.59 cputime=286.413 memavail=7397464 print_time=3715.073 buffer_time=2.276 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 44 Hz
Stats 3691.3: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21008224 bytes_read=2828570 bytes_retransmit=9 bytes_invalid=0 send_seq=374694 receive_seq=374694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=10187 freq=400016022 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23140 bytes_read=73278 bytes_retransmit=0 bytes_invalid=0 send_seq=3828 receive_seq=3828 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997115 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134836 bytes_read=4096021 bytes_retransmit=9 bytes_invalid=0 send_seq=18189 receive_seq=18189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997533 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=77153 bytes_read=1651626 bytes_retransmit=9 bytes_invalid=0 send_seq=10039 receive_seq=10039 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997365 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23407 bytes_read=940139 bytes_retransmit=9 bytes_invalid=0 send_seq=3842 receive_seq=3842 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997565 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23893 bytes_read=71843 bytes_retransmit=9 bytes_invalid=0 send_seq=3829 receive_seq=3829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999413 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77985 bytes_read=1542465 bytes_retransmit=0 bytes_invalid=0 send_seq=8388 receive_seq=8388 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998616 coil_temp=17.3 refs=0 mcu_temp=20.49 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.0 th2: temp=50.0 th3: temp=47.8 sysload=0.59 cputime=286.531 memavail=7397464 print_time=3715.992 buffer_time=2.195 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 45 Hz
Stats 3692.3: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21018242 bytes_read=2829775 bytes_retransmit=9 bytes_invalid=0 send_seq=374873 receive_seq=374873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=7722 freq=400016038 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23146 bytes_read=73294 bytes_retransmit=0 bytes_invalid=0 send_seq=3829 receive_seq=3829 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997126 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134912 bytes_read=4099091 bytes_retransmit=9 bytes_invalid=0 send_seq=18200 receive_seq=18200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997707 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=77229 bytes_read=1654684 bytes_retransmit=9 bytes_invalid=0 send_seq=10050 receive_seq=10050 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997372 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23413 bytes_read=940388 bytes_retransmit=9 bytes_invalid=0 send_seq=3843 receive_seq=3843 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997577 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23899 bytes_read=71870 bytes_retransmit=9 bytes_invalid=0 send_seq=3830 receive_seq=3830 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999417 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77991 bytes_read=1542821 bytes_retransmit=0 bytes_invalid=0 send_seq=8389 receive_seq=8389 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998622 coil_temp=17.3 refs=0 mcu_temp=20.49 supply_voltage=3.012 th0: temp=46.9 th1: temp=46.2 th2: temp=50.0 th3: temp=47.7 sysload=0.59 cputime=286.656 memavail=7397464 print_time=3716.876 buffer_time=2.078 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 46 Hz
Stats 3693.3: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21027260 bytes_read=2830908 bytes_retransmit=9 bytes_invalid=0 send_seq=375033 receive_seq=375033 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=8336 freq=400016060 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23152 bytes_read=73310 bytes_retransmit=0 bytes_invalid=0 send_seq=3830 receive_seq=3830 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999206 adj=49997105 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134988 bytes_read=4102163 bytes_retransmit=9 bytes_invalid=0 send_seq=18211 receive_seq=18211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997675 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=77305 bytes_read=1657844 bytes_retransmit=9 bytes_invalid=0 send_seq=10061 receive_seq=10061 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997328 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23419 bytes_read=940682 bytes_retransmit=9 bytes_invalid=0 send_seq=3844 receive_seq=3844 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997545 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23905 bytes_read=71886 bytes_retransmit=9 bytes_invalid=0 send_seq=3831 receive_seq=3831 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999413 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=77997 bytes_read=1543177 bytes_retransmit=0 bytes_invalid=0 send_seq=8390 receive_seq=8390 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998596 coil_temp=17.3 refs=0 mcu_temp=20.49 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.2 th2: temp=49.8 th3: temp=47.9 sysload=0.54 cputime=286.780 memavail=7397464 print_time=3717.798 buffer_time=2.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 47 Hz
Stats 3694.3: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21035980 bytes_read=2832003 bytes_retransmit=9 bytes_invalid=0 send_seq=375190 receive_seq=375190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=10644 freq=400016068 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=23158 bytes_read=73339 bytes_retransmit=0 bytes_invalid=0 send_seq=3831 receive_seq=3831 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999206 adj=49997063 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135064 bytes_read=4105277 bytes_retransmit=9 bytes_invalid=0 send_seq=18222 receive_seq=18222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997626 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=77381 bytes_read=1660901 bytes_retransmit=9 bytes_invalid=0 send_seq=10072 receive_seq=10072 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997279 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23425 bytes_read=940916 bytes_retransmit=9 bytes_invalid=0 send_seq=3845 receive_seq=3845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997511 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23911 bytes_read=71902 bytes_retransmit=9 bytes_invalid=0 send_seq=3832 receive_seq=3832 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999405 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78003 bytes_read=1543533 bytes_retransmit=0 bytes_invalid=0 send_seq=8391 receive_seq=8391 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998571 coil_temp=17.3 refs=0 mcu_temp=20.49 supply_voltage=3.012 th0: temp=46.8 th1: temp=46.3 th2: temp=49.8 th3: temp=47.8 sysload=0.54 cputime=286.913 memavail=7397464 print_time=3719.009 buffer_time=2.210 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 48 Hz
Stats 3695.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21046088 bytes_read=2833234 bytes_retransmit=9 bytes_invalid=0 send_seq=375371 receive_seq=375371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=8315 freq=400016048 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=23164 bytes_read=73355 bytes_retransmit=0 bytes_invalid=0 send_seq=3832 receive_seq=3832 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999206 adj=49997094 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135140 bytes_read=4108349 bytes_retransmit=9 bytes_invalid=0 send_seq=18233 receive_seq=18233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997613 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=77457 bytes_read=1663959 bytes_retransmit=9 bytes_invalid=0 send_seq=10083 receive_seq=10083 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997308 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23431 bytes_read=941150 bytes_retransmit=9 bytes_invalid=0 send_seq=3846 receive_seq=3846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997536 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23917 bytes_read=71918 bytes_retransmit=9 bytes_invalid=0 send_seq=3833 receive_seq=3833 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999410 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78009 bytes_read=1543889 bytes_retransmit=0 bytes_invalid=0 send_seq=8392 receive_seq=8392 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998586 coil_temp=17.3 refs=0 mcu_temp=20.47 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.2 th2: temp=49.9 th3: temp=47.9 sysload=0.54 cputime=287.038 memavail=7397464 print_time=3719.895 buffer_time=2.096 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 49 Hz
Stats 3696.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21055376 bytes_read=2834393 bytes_retransmit=9 bytes_invalid=0 send_seq=375535 receive_seq=375535 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=9148 freq=400016026 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=23170 bytes_read=73371 bytes_retransmit=0 bytes_invalid=0 send_seq=3833 receive_seq=3833 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999207 adj=49997137 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135216 bytes_read=4111436 bytes_retransmit=9 bytes_invalid=0 send_seq=18244 receive_seq=18244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997679 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=77533 bytes_read=1667045 bytes_retransmit=9 bytes_invalid=0 send_seq=10094 receive_seq=10094 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997346 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23437 bytes_read=941444 bytes_retransmit=9 bytes_invalid=0 send_seq=3847 receive_seq=3847 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997568 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23923 bytes_read=71934 bytes_retransmit=9 bytes_invalid=0 send_seq=3834 receive_seq=3834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999418 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78015 bytes_read=1544245 bytes_retransmit=0 bytes_invalid=0 send_seq=8393 receive_seq=8393 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998608 coil_temp=17.3 refs=0 mcu_temp=20.46 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.3 th2: temp=50.4 th3: temp=47.9 sysload=0.54 cputime=287.164 memavail=7396024 print_time=3720.816 buffer_time=2.016 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 50 Hz
Stats 3697.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21064319 bytes_read=2835503 bytes_retransmit=9 bytes_invalid=0 send_seq=375695 receive_seq=375695 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=11607 freq=400016009 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=23176 bytes_read=73387 bytes_retransmit=0 bytes_invalid=0 send_seq=3834 receive_seq=3834 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999206 adj=49997185 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135292 bytes_read=4114493 bytes_retransmit=9 bytes_invalid=0 send_seq=18255 receive_seq=18255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997715 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=77609 bytes_read=1670103 bytes_retransmit=9 bytes_invalid=0 send_seq=10105 receive_seq=10105 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997392 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23443 bytes_read=941693 bytes_retransmit=9 bytes_invalid=0 send_seq=3848 receive_seq=3848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997600 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23929 bytes_read=71961 bytes_retransmit=9 bytes_invalid=0 send_seq=3835 receive_seq=3835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78021 bytes_read=1544601 bytes_retransmit=0 bytes_invalid=0 send_seq=8394 receive_seq=8394 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998627 coil_temp=17.3 refs=0 mcu_temp=20.46 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.2 th2: temp=49.9 th3: temp=48.0 sysload=0.54 cputime=287.302 memavail=7395772 print_time=3722.019 buffer_time=2.219 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 51 Hz
Stats 3698.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21074924 bytes_read=2836753 bytes_retransmit=9 bytes_invalid=0 send_seq=375883 receive_seq=375883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=8955 freq=400015996 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=23182 bytes_read=73403 bytes_retransmit=0 bytes_invalid=0 send_seq=3835 receive_seq=3835 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999206 adj=49997212 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135368 bytes_read=4117564 bytes_retransmit=9 bytes_invalid=0 send_seq=18266 receive_seq=18266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997715 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=77685 bytes_read=1673177 bytes_retransmit=9 bytes_invalid=0 send_seq=10116 receive_seq=10116 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997550 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23449 bytes_read=941927 bytes_retransmit=9 bytes_invalid=0 send_seq=3849 receive_seq=3849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23935 bytes_read=71977 bytes_retransmit=9 bytes_invalid=0 send_seq=3836 receive_seq=3836 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78027 bytes_read=1544957 bytes_retransmit=0 bytes_invalid=0 send_seq=8395 receive_seq=8395 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998645 coil_temp=17.3 refs=0 mcu_temp=20.46 supply_voltage=3.012 th0: temp=46.5 th1: temp=46.2 th2: temp=49.9 th3: temp=48.0 sysload=0.49 cputime=287.436 memavail=7395776 print_time=3722.906 buffer_time=2.105 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 52 Hz
Stats 3699.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21084722 bytes_read=2837962 bytes_retransmit=9 bytes_invalid=0 send_seq=376057 receive_seq=376057 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=9308 freq=400015997 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23188 bytes_read=73432 bytes_retransmit=0 bytes_invalid=0 send_seq=3836 receive_seq=3836 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999207 adj=49997230 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135444 bytes_read=4120635 bytes_retransmit=9 bytes_invalid=0 send_seq=18277 receive_seq=18277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997723 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=77761 bytes_read=1676263 bytes_retransmit=9 bytes_invalid=0 send_seq=10127 receive_seq=10127 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23455 bytes_read=942221 bytes_retransmit=9 bytes_invalid=0 send_seq=3850 receive_seq=3850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23941 bytes_read=71993 bytes_retransmit=9 bytes_invalid=0 send_seq=3837 receive_seq=3837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78033 bytes_read=1545313 bytes_retransmit=0 bytes_invalid=0 send_seq=8396 receive_seq=8396 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998660 coil_temp=17.3 refs=0 mcu_temp=20.46 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.4 th2: temp=50.2 th3: temp=47.9 sysload=0.49 cputime=287.562 memavail=7395784 print_time=3723.822 buffer_time=2.020 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 53 Hz
Stats 3700.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21093834 bytes_read=2839113 bytes_retransmit=9 bytes_invalid=0 send_seq=376222 receive_seq=376222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=12168 freq=400015973 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23194 bytes_read=73448 bytes_retransmit=0 bytes_invalid=0 send_seq=3837 receive_seq=3837 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997233 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135520 bytes_read=4123692 bytes_retransmit=9 bytes_invalid=0 send_seq=18288 receive_seq=18288 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997712 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=77837 bytes_read=1679378 bytes_retransmit=9 bytes_invalid=0 send_seq=10138 receive_seq=10138 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23461 bytes_read=942455 bytes_retransmit=9 bytes_invalid=0 send_seq=3851 receive_seq=3851 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997629 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23947 bytes_read=72009 bytes_retransmit=9 bytes_invalid=0 send_seq=3838 receive_seq=3838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=30.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78039 bytes_read=1545669 bytes_retransmit=0 bytes_invalid=0 send_seq=8397 receive_seq=8397 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998656 coil_temp=17.3 refs=0 mcu_temp=20.46 supply_voltage=3.012 th0: temp=46.9 th1: temp=46.3 th2: temp=49.9 th3: temp=47.9 sysload=0.49 cputime=287.698 memavail=7395784 print_time=3725.018 buffer_time=2.216 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 54 Hz
Stats 3701.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21104457 bytes_read=2840363 bytes_retransmit=9 bytes_invalid=0 send_seq=376410 receive_seq=376410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=43 upcoming_bytes=9925 freq=400015953 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23200 bytes_read=73464 bytes_retransmit=0 bytes_invalid=0 send_seq=3838 receive_seq=3838 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997315 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135596 bytes_read=4126781 bytes_retransmit=9 bytes_invalid=0 send_seq=18299 receive_seq=18299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997736 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=77913 bytes_read=1682435 bytes_retransmit=9 bytes_invalid=0 send_seq=10149 receive_seq=10149 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997582 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23467 bytes_read=942689 bytes_retransmit=9 bytes_invalid=0 send_seq=3852 receive_seq=3852 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997690 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23953 bytes_read=72025 bytes_retransmit=9 bytes_invalid=0 send_seq=3839 receive_seq=3839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78045 bytes_read=1546025 bytes_retransmit=0 bytes_invalid=0 send_seq=8398 receive_seq=8398 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998685 coil_temp=17.3 refs=0 mcu_temp=20.46 supply_voltage=3.012 th0: temp=46.9 th1: temp=45.9 th2: temp=50.0 th3: temp=47.9 sysload=0.49 cputime=287.841 memavail=7391012 print_time=3725.930 buffer_time=2.128 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 55 Hz
Stats 3702.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21114773 bytes_read=2841607 bytes_retransmit=9 bytes_invalid=0 send_seq=376591 receive_seq=376591 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=9860 freq=400015959 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23206 bytes_read=73479 bytes_retransmit=0 bytes_invalid=0 send_seq=3839 receive_seq=3839 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997350 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135672 bytes_read=4129910 bytes_retransmit=9 bytes_invalid=0 send_seq=18310 receive_seq=18310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997773 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=77989 bytes_read=1685522 bytes_retransmit=9 bytes_invalid=0 send_seq=10160 receive_seq=10160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997593 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23473 bytes_read=942998 bytes_retransmit=9 bytes_invalid=0 send_seq=3853 receive_seq=3853 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997750 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23959 bytes_read=72052 bytes_retransmit=9 bytes_invalid=0 send_seq=3840 receive_seq=3840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999460 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78051 bytes_read=1546381 bytes_retransmit=0 bytes_invalid=0 send_seq=8399 receive_seq=8399 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998692 coil_temp=17.3 refs=0 mcu_temp=20.46 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.2 th2: temp=49.7 th3: temp=47.9 sysload=0.49 cputime=287.971 memavail=7397632 print_time=3726.832 buffer_time=2.028 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 56 Hz
Stats 3703.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21124201 bytes_read=2842720 bytes_retransmit=9 bytes_invalid=0 send_seq=376752 receive_seq=376752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=12643 freq=400015978 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23212 bytes_read=73494 bytes_retransmit=0 bytes_invalid=0 send_seq=3840 receive_seq=3840 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997319 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135748 bytes_read=4132968 bytes_retransmit=9 bytes_invalid=0 send_seq=18321 receive_seq=18321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997872 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=78065 bytes_read=1688596 bytes_retransmit=9 bytes_invalid=0 send_seq=10171 receive_seq=10171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997546 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23479 bytes_read=943232 bytes_retransmit=9 bytes_invalid=0 send_seq=3854 receive_seq=3854 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997735 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23965 bytes_read=72068 bytes_retransmit=9 bytes_invalid=0 send_seq=3841 receive_seq=3841 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78057 bytes_read=1546737 bytes_retransmit=0 bytes_invalid=0 send_seq=8400 receive_seq=8400 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998683 coil_temp=17.3 refs=0 mcu_temp=20.46 supply_voltage=3.012 th0: temp=46.5 th1: temp=46.4 th2: temp=49.9 th3: temp=48.0 sysload=0.45 cputime=288.108 memavail=7397408 print_time=3728.035 buffer_time=2.231 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 57 Hz
Stats 3704.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21135035 bytes_read=2843987 bytes_retransmit=9 bytes_invalid=0 send_seq=376944 receive_seq=376944 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=10567 freq=400015961 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23218 bytes_read=73522 bytes_retransmit=0 bytes_invalid=0 send_seq=3841 receive_seq=3841 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997262 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135824 bytes_read=4136041 bytes_retransmit=9 bytes_invalid=0 send_seq=18332 receive_seq=18332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997882 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=78141 bytes_read=1691653 bytes_retransmit=9 bytes_invalid=0 send_seq=10182 receive_seq=10182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997495 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23485 bytes_read=943466 bytes_retransmit=9 bytes_invalid=0 send_seq=3855 receive_seq=3855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23971 bytes_read=72084 bytes_retransmit=9 bytes_invalid=0 send_seq=3842 receive_seq=3842 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78063 bytes_read=1547093 bytes_retransmit=0 bytes_invalid=0 send_seq=8401 receive_seq=8401 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998675 coil_temp=17.3 refs=0 mcu_temp=20.46 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.3 th2: temp=50.0 th3: temp=47.7 sysload=0.45 cputime=288.241 memavail=7397408 print_time=3728.956 buffer_time=2.152 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 58 Hz
Stats 3705.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21145673 bytes_read=2845272 bytes_retransmit=9 bytes_invalid=0 send_seq=377130 receive_seq=377130 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=10600 freq=400015959 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23224 bytes_read=73537 bytes_retransmit=0 bytes_invalid=0 send_seq=3842 receive_seq=3842 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997274 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135900 bytes_read=4139114 bytes_retransmit=9 bytes_invalid=0 send_seq=18343 receive_seq=18343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997871 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=78217 bytes_read=1694737 bytes_retransmit=9 bytes_invalid=0 send_seq=10193 receive_seq=10193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997512 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23491 bytes_read=943760 bytes_retransmit=9 bytes_invalid=0 send_seq=3856 receive_seq=3856 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997700 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23977 bytes_read=72100 bytes_retransmit=9 bytes_invalid=0 send_seq=3843 receive_seq=3843 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78069 bytes_read=1547449 bytes_retransmit=0 bytes_invalid=0 send_seq=8402 receive_seq=8402 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998680 coil_temp=17.3 refs=0 mcu_temp=20.45 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.3 th2: temp=49.8 th3: temp=47.9 sysload=0.45 cputime=288.371 memavail=7397408 print_time=3729.845 buffer_time=2.040 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 59 Hz
Stats 3706.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21155147 bytes_read=2846432 bytes_retransmit=9 bytes_invalid=0 send_seq=377300 receive_seq=377300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=13635 freq=400015953 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23230 bytes_read=73552 bytes_retransmit=0 bytes_invalid=0 send_seq=3843 receive_seq=3843 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997263 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135969 bytes_read=4142165 bytes_retransmit=9 bytes_invalid=0 send_seq=18353 receive_seq=18353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997821 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=78286 bytes_read=1697771 bytes_retransmit=9 bytes_invalid=0 send_seq=10203 receive_seq=10203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997499 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23497 bytes_read=943994 bytes_retransmit=9 bytes_invalid=0 send_seq=3857 receive_seq=3857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23983 bytes_read=72116 bytes_retransmit=9 bytes_invalid=0 send_seq=3844 receive_seq=3844 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78075 bytes_read=1547805 bytes_retransmit=0 bytes_invalid=0 send_seq=8403 receive_seq=8403 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998673 coil_temp=17.3 refs=0 mcu_temp=20.44 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.3 th2: temp=49.9 th3: temp=47.8 sysload=0.45 cputime=288.512 memavail=7396412 print_time=3731.047 buffer_time=2.240 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 60 Hz
Stats 3707.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21166717 bytes_read=2847752 bytes_retransmit=9 bytes_invalid=0 send_seq=377502 receive_seq=377502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=11139 freq=400015986 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23236 bytes_read=73567 bytes_retransmit=0 bytes_invalid=0 send_seq=3844 receive_seq=3844 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997253 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=136045 bytes_read=4145235 bytes_retransmit=9 bytes_invalid=0 send_seq=18364 receive_seq=18364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997795 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=78362 bytes_read=1700830 bytes_retransmit=9 bytes_invalid=0 send_seq=10214 receive_seq=10214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23503 bytes_read=944243 bytes_retransmit=9 bytes_invalid=0 send_seq=3858 receive_seq=3858 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23989 bytes_read=72143 bytes_retransmit=9 bytes_invalid=0 send_seq=3845 receive_seq=3845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78081 bytes_read=1548161 bytes_retransmit=0 bytes_invalid=0 send_seq=8404 receive_seq=8404 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998669 coil_temp=17.3 refs=0 mcu_temp=20.44 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.3 th2: temp=50.0 th3: temp=47.9 sysload=0.45 cputime=288.648 memavail=7396412 print_time=3731.975 buffer_time=2.168 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 61 Hz
Stats 3708.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21177492 bytes_read=2849041 bytes_retransmit=9 bytes_invalid=0 send_seq=377692 receive_seq=377692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=11100 freq=400015973 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23242 bytes_read=73583 bytes_retransmit=0 bytes_invalid=0 send_seq=3845 receive_seq=3845 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997195 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=136121 bytes_read=4148305 bytes_retransmit=9 bytes_invalid=0 send_seq=18375 receive_seq=18375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997689 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=78438 bytes_read=1703990 bytes_retransmit=9 bytes_invalid=0 send_seq=10225 receive_seq=10225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997419 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23509 bytes_read=944537 bytes_retransmit=9 bytes_invalid=0 send_seq=3859 receive_seq=3859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997604 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=23995 bytes_read=72159 bytes_retransmit=9 bytes_invalid=0 send_seq=3846 receive_seq=3846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78087 bytes_read=1548517 bytes_retransmit=0 bytes_invalid=0 send_seq=8405 receive_seq=8405 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998636 coil_temp=17.3 refs=0 mcu_temp=20.44 supply_voltage=3.012 th0: temp=46.8 th1: temp=46.4 th2: temp=49.9 th3: temp=47.9 sysload=0.42 cputime=288.778 memavail=7396412 print_time=3732.865 buffer_time=2.058 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 62 Hz
Stats 3709.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21187330 bytes_read=2850211 bytes_retransmit=9 bytes_invalid=0 send_seq=377864 receive_seq=377864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=14079 freq=400015955 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23248 bytes_read=73612 bytes_retransmit=0 bytes_invalid=0 send_seq=3846 receive_seq=3846 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997216 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=136197 bytes_read=4151421 bytes_retransmit=9 bytes_invalid=0 send_seq=18386 receive_seq=18386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997697 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=78514 bytes_read=1707050 bytes_retransmit=9 bytes_invalid=0 send_seq=10236 receive_seq=10236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997436 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23515 bytes_read=944771 bytes_retransmit=9 bytes_invalid=0 send_seq=3860 receive_seq=3860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997621 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24001 bytes_read=72175 bytes_retransmit=9 bytes_invalid=0 send_seq=3847 receive_seq=3847 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78093 bytes_read=1548873 bytes_retransmit=0 bytes_invalid=0 send_seq=8406 receive_seq=8406 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998649 coil_temp=17.3 refs=0 mcu_temp=20.44 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.5 th2: temp=50.0 th3: temp=48.0 sysload=0.42 cputime=288.919 memavail=7396412 print_time=3734.065 buffer_time=2.256 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 63 Hz
Stats 3710.3: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21198973 bytes_read=2851557 bytes_retransmit=9 bytes_invalid=0 send_seq=378068 receive_seq=378068 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=11965 freq=400015973 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23254 bytes_read=73628 bytes_retransmit=0 bytes_invalid=0 send_seq=3847 receive_seq=3847 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997230 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=136273 bytes_read=4154493 bytes_retransmit=9 bytes_invalid=0 send_seq=18397 receive_seq=18397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997718 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=78590 bytes_read=1710122 bytes_retransmit=9 bytes_invalid=0 send_seq=10247 receive_seq=10247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997473 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23521 bytes_read=945005 bytes_retransmit=9 bytes_invalid=0 send_seq=3861 receive_seq=3861 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24007 bytes_read=72191 bytes_retransmit=9 bytes_invalid=0 send_seq=3848 receive_seq=3848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78099 bytes_read=1549229 bytes_retransmit=0 bytes_invalid=0 send_seq=8407 receive_seq=8407 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998659 coil_temp=17.3 refs=0 mcu_temp=20.45 supply_voltage=3.012 th0: temp=47.3 th1: temp=46.4 th2: temp=50.0 th3: temp=48.0 sysload=0.42 cputime=289.056 memavail=7396424 print_time=3734.993 buffer_time=2.184 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 64 Hz
Stats 3711.3: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21209989 bytes_read=2852856 bytes_retransmit=9 bytes_invalid=0 send_seq=378260 receive_seq=378260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=11819 freq=400015967 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23260 bytes_read=73644 bytes_retransmit=0 bytes_invalid=0 send_seq=3848 receive_seq=3848 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997194 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=136349 bytes_read=4157581 bytes_retransmit=9 bytes_invalid=0 send_seq=18408 receive_seq=18408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997651 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=78666 bytes_read=1713193 bytes_retransmit=9 bytes_invalid=0 send_seq=10258 receive_seq=10258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997429 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23527 bytes_read=945299 bytes_retransmit=9 bytes_invalid=0 send_seq=3862 receive_seq=3862 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997605 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24013 bytes_read=72207 bytes_retransmit=9 bytes_invalid=0 send_seq=3849 receive_seq=3849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78105 bytes_read=1549585 bytes_retransmit=0 bytes_invalid=0 send_seq=8408 receive_seq=8408 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998641 coil_temp=17.3 refs=0 mcu_temp=20.44 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.7 th2: temp=50.1 th3: temp=48.0 sysload=0.42 cputime=289.185 memavail=7396424 print_time=3735.864 buffer_time=2.055 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 65 Hz
Stats 3712.3: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21220123 bytes_read=2854061 bytes_retransmit=9 bytes_invalid=0 send_seq=378439 receive_seq=378439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=14945 freq=400015950 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23266 bytes_read=73660 bytes_retransmit=0 bytes_invalid=0 send_seq=3849 receive_seq=3849 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997203 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=136425 bytes_read=4160637 bytes_retransmit=9 bytes_invalid=0 send_seq=18419 receive_seq=18419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997646 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=78742 bytes_read=1716251 bytes_retransmit=9 bytes_invalid=0 send_seq=10269 receive_seq=10269 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997497 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23533 bytes_read=945548 bytes_retransmit=9 bytes_invalid=0 send_seq=3863 receive_seq=3863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24019 bytes_read=72234 bytes_retransmit=9 bytes_invalid=0 send_seq=3850 receive_seq=3850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78111 bytes_read=1549941 bytes_retransmit=0 bytes_invalid=0 send_seq=8409 receive_seq=8409 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998671 coil_temp=17.3 refs=0 mcu_temp=20.44 supply_voltage=3.012 th0: temp=46.9 th1: temp=46.5 th2: temp=49.9 th3: temp=48.1 sysload=0.42 cputime=289.329 memavail=7396424 print_time=3737.066 buffer_time=2.256 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 66 Hz
Stats 3713.3: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21232208 bytes_read=2855421 bytes_retransmit=9 bytes_invalid=0 send_seq=378649 receive_seq=378649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=12804 freq=400015948 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23272 bytes_read=73676 bytes_retransmit=0 bytes_invalid=0 send_seq=3850 receive_seq=3850 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999207 adj=49997220 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=136501 bytes_read=4163709 bytes_retransmit=9 bytes_invalid=0 send_seq=18430 receive_seq=18430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997662 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=78818 bytes_read=1719339 bytes_retransmit=9 bytes_invalid=0 send_seq=10280 receive_seq=10280 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997514 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23539 bytes_read=945782 bytes_retransmit=9 bytes_invalid=0 send_seq=3864 receive_seq=3864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997692 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24025 bytes_read=72250 bytes_retransmit=9 bytes_invalid=0 send_seq=3851 receive_seq=3851 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78117 bytes_read=1550297 bytes_retransmit=0 bytes_invalid=0 send_seq=8410 receive_seq=8410 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998675 coil_temp=17.3 refs=0 mcu_temp=20.44 supply_voltage=3.012 th0: temp=46.8 th1: temp=46.6 th2: temp=50.1 th3: temp=48.0 sysload=0.38 cputime=289.467 memavail=7396424 print_time=3737.998 buffer_time=2.188 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 67 Hz
Stats 3714.3: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21243765 bytes_read=2856761 bytes_retransmit=9 bytes_invalid=0 send_seq=378850 receive_seq=378850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=12352 freq=400015931 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23278 bytes_read=73705 bytes_retransmit=0 bytes_invalid=0 send_seq=3851 receive_seq=3851 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999207 adj=49997220 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=136577 bytes_read=4166779 bytes_retransmit=9 bytes_invalid=0 send_seq=18441 receive_seq=18441 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997649 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=78894 bytes_read=1722411 bytes_retransmit=9 bytes_invalid=0 send_seq=10291 receive_seq=10291 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23545 bytes_read=946076 bytes_retransmit=9 bytes_invalid=0 send_seq=3865 receive_seq=3865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24031 bytes_read=72266 bytes_retransmit=9 bytes_invalid=0 send_seq=3852 receive_seq=3852 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78123 bytes_read=1550653 bytes_retransmit=0 bytes_invalid=0 send_seq=8411 receive_seq=8411 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998668 coil_temp=17.3 refs=0 mcu_temp=20.44 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.6 th2: temp=50.1 th3: temp=48.1 sysload=0.38 cputime=289.600 memavail=7396424 print_time=3738.882 buffer_time=2.071 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 68 Hz
Stats 3715.3: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21254261 bytes_read=2858011 bytes_retransmit=9 bytes_invalid=0 send_seq=379035 receive_seq=379035 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=15510 freq=400015932 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23284 bytes_read=73721 bytes_retransmit=0 bytes_invalid=0 send_seq=3852 receive_seq=3852 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999207 adj=49997245 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=136653 bytes_read=4169895 bytes_retransmit=9 bytes_invalid=0 send_seq=18452 receive_seq=18452 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997692 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=78970 bytes_read=1725525 bytes_retransmit=9 bytes_invalid=0 send_seq=10302 receive_seq=10302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23551 bytes_read=946310 bytes_retransmit=9 bytes_invalid=0 send_seq=3866 receive_seq=3866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24037 bytes_read=72282 bytes_retransmit=9 bytes_invalid=0 send_seq=3853 receive_seq=3853 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999449 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78129 bytes_read=1551023 bytes_retransmit=0 bytes_invalid=0 send_seq=8412 receive_seq=8412 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998681 coil_temp=17.3 refs=0 mcu_temp=20.44 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.5 th2: temp=49.9 th3: temp=48.0 sysload=0.38 cputime=289.748 memavail=7396436 print_time=3740.078 buffer_time=2.260 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 69 Hz
Stats 3716.3: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21266533 bytes_read=2859391 bytes_retransmit=9 bytes_invalid=0 send_seq=379249 receive_seq=379249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=13516 freq=400015921 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23290 bytes_read=73737 bytes_retransmit=0 bytes_invalid=0 send_seq=3853 receive_seq=3853 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997234 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=136729 bytes_read=4173001 bytes_retransmit=9 bytes_invalid=0 send_seq=18463 receive_seq=18463 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997742 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=79046 bytes_read=1728596 bytes_retransmit=9 bytes_invalid=0 send_seq=10313 receive_seq=10313 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23557 bytes_read=946559 bytes_retransmit=9 bytes_invalid=0 send_seq=3867 receive_seq=3867 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24043 bytes_read=72298 bytes_retransmit=9 bytes_invalid=0 send_seq=3854 receive_seq=3854 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78135 bytes_read=1551368 bytes_retransmit=0 bytes_invalid=0 send_seq=8413 receive_seq=8413 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998678 coil_temp=17.3 refs=0 mcu_temp=20.44 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.7 th2: temp=50.0 th3: temp=48.1 sysload=0.38 cputime=289.891 memavail=7395440 print_time=3741.015 buffer_time=2.196 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 70 Hz
Stats 3717.3: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21278497 bytes_read=2860770 bytes_retransmit=9 bytes_invalid=0 send_seq=379457 receive_seq=379457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=12784 freq=400015936 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23296 bytes_read=73753 bytes_retransmit=0 bytes_invalid=0 send_seq=3854 receive_seq=3854 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997274 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=136805 bytes_read=4176057 bytes_retransmit=9 bytes_invalid=0 send_seq=18474 receive_seq=18474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997734 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=79122 bytes_read=1731667 bytes_retransmit=9 bytes_invalid=0 send_seq=10324 receive_seq=10324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997527 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23563 bytes_read=946853 bytes_retransmit=9 bytes_invalid=0 send_seq=3868 receive_seq=3868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24049 bytes_read=72325 bytes_retransmit=9 bytes_invalid=0 send_seq=3855 receive_seq=3855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78141 bytes_read=1551712 bytes_retransmit=0 bytes_invalid=0 send_seq=8414 receive_seq=8414 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998684 coil_temp=17.3 refs=0 mcu_temp=20.42 supply_voltage=3.012 th0: temp=47.2 th1: temp=46.7 th2: temp=50.1 th3: temp=48.2 sysload=0.38 cputime=290.025 memavail=7395440 print_time=3741.887 buffer_time=2.068 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 71 Hz
Stats 3718.3: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21289115 bytes_read=2862010 bytes_retransmit=9 bytes_invalid=0 send_seq=379643 receive_seq=379643 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=16263 freq=400015938 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23302 bytes_read=73769 bytes_retransmit=0 bytes_invalid=0 send_seq=3855 receive_seq=3855 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997237 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=136874 bytes_read=4179149 bytes_retransmit=9 bytes_invalid=0 send_seq=18484 receive_seq=18484 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997679 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=79198 bytes_read=1734798 bytes_retransmit=9 bytes_invalid=0 send_seq=10335 receive_seq=10335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997546 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23569 bytes_read=947087 bytes_retransmit=9 bytes_invalid=0 send_seq=3869 receive_seq=3869 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997629 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24055 bytes_read=72341 bytes_retransmit=9 bytes_invalid=0 send_seq=3856 receive_seq=3856 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78147 bytes_read=1552057 bytes_retransmit=0 bytes_invalid=0 send_seq=8415 receive_seq=8415 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998675 coil_temp=17.3 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.6 th2: temp=50.2 th3: temp=48.1 sysload=0.35 cputime=290.182 memavail=7389644 print_time=3743.092 buffer_time=2.263 print_stall=0 extruder: target=0 temp=19.9 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 72 Hz
Stats 3719.3: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21301757 bytes_read=2863425 bytes_retransmit=9 bytes_invalid=0 send_seq=379864 receive_seq=379864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=14546 freq=400015940 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23308 bytes_read=73798 bytes_retransmit=0 bytes_invalid=0 send_seq=3856 receive_seq=3856 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997231 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=136950 bytes_read=4182233 bytes_retransmit=9 bytes_invalid=0 send_seq=18495 receive_seq=18495 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997756 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=79267 bytes_read=1737861 bytes_retransmit=9 bytes_invalid=0 send_seq=10345 receive_seq=10345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23575 bytes_read=947351 bytes_retransmit=9 bytes_invalid=0 send_seq=3870 receive_seq=3870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24061 bytes_read=72357 bytes_retransmit=9 bytes_invalid=0 send_seq=3857 receive_seq=3857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78153 bytes_read=1552402 bytes_retransmit=0 bytes_invalid=0 send_seq=8416 receive_seq=8416 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998664 coil_temp=17.3 refs=0 mcu_temp=20.41 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.7 th2: temp=50.0 th3: temp=48.0 sysload=0.35 cputime=290.329 memavail=7395840 print_time=3744.032 buffer_time=2.202 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 73 Hz
Stats 3720.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21314280 bytes_read=2864865 bytes_retransmit=9 bytes_invalid=0 send_seq=380081 receive_seq=380081 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=23 upcoming_bytes=13428 freq=400015958 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23314 bytes_read=73814 bytes_retransmit=0 bytes_invalid=0 send_seq=3857 receive_seq=3857 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997228 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=137026 bytes_read=4185290 bytes_retransmit=9 bytes_invalid=0 send_seq=18506 receive_seq=18506 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997719 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=79343 bytes_read=1740921 bytes_retransmit=9 bytes_invalid=0 send_seq=10356 receive_seq=10356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997571 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23581 bytes_read=947615 bytes_retransmit=9 bytes_invalid=0 send_seq=3871 receive_seq=3871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997611 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24067 bytes_read=72373 bytes_retransmit=9 bytes_invalid=0 send_seq=3858 receive_seq=3858 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78159 bytes_read=1552747 bytes_retransmit=0 bytes_invalid=0 send_seq=8417 receive_seq=8417 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998658 coil_temp=17.3 refs=0 mcu_temp=20.41 supply_voltage=3.012 th0: temp=47.4 th1: temp=46.7 th2: temp=50.1 th3: temp=48.1 sysload=0.35 cputime=290.470 memavail=7395844 print_time=3744.906 buffer_time=2.075 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 74 Hz
Stats 3721.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21324956 bytes_read=2866100 bytes_retransmit=9 bytes_invalid=0 send_seq=380266 receive_seq=380266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=13997 freq=400016169 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23320 bytes_read=73830 bytes_retransmit=0 bytes_invalid=0 send_seq=3858 receive_seq=3858 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997197 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=137102 bytes_read=4188365 bytes_retransmit=9 bytes_invalid=0 send_seq=18517 receive_seq=18517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997763 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=79419 bytes_read=1743978 bytes_retransmit=9 bytes_invalid=0 send_seq=10367 receive_seq=10367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23587 bytes_read=947849 bytes_retransmit=9 bytes_invalid=0 send_seq=3872 receive_seq=3872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997579 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24073 bytes_read=72389 bytes_retransmit=9 bytes_invalid=0 send_seq=3859 receive_seq=3859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78165 bytes_read=1553092 bytes_retransmit=0 bytes_invalid=0 send_seq=8418 receive_seq=8418 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998640 coil_temp=17.3 refs=0 mcu_temp=20.41 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.7 th2: temp=50.0 th3: temp=48.0 sysload=0.35 cputime=290.612 memavail=7395844 print_time=3745.843 buffer_time=2.012 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 75 Hz
Stats 3722.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21338103 bytes_read=2867555 bytes_retransmit=9 bytes_invalid=0 send_seq=380495 receive_seq=380495 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=15328 freq=400016141 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23326 bytes_read=73846 bytes_retransmit=0 bytes_invalid=0 send_seq=3859 receive_seq=3859 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49996846 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=137178 bytes_read=4191449 bytes_retransmit=9 bytes_invalid=0 send_seq=18528 receive_seq=18528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997268 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=79495 bytes_read=1747062 bytes_retransmit=9 bytes_invalid=0 send_seq=10378 receive_seq=10378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997038 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23593 bytes_read=948128 bytes_retransmit=9 bytes_invalid=0 send_seq=3873 receive_seq=3873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997243 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24079 bytes_read=72416 bytes_retransmit=9 bytes_invalid=0 send_seq=3860 receive_seq=3860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999351 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78171 bytes_read=1553437 bytes_retransmit=0 bytes_invalid=0 send_seq=8419 receive_seq=8419 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998416 coil_temp=17.3 refs=0 mcu_temp=20.41 supply_voltage=3.012 th0: temp=46.9 th1: temp=46.8 th2: temp=50.2 th3: temp=48.0 sysload=0.35 cputime=290.769 memavail=7395844 print_time=3747.038 buffer_time=2.207 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 76 Hz
Stats 3723.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21351007 bytes_read=2869025 bytes_retransmit=9 bytes_invalid=0 send_seq=380719 receive_seq=380719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=43 upcoming_bytes=13757 freq=400016105 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23338 bytes_read=73878 bytes_retransmit=0 bytes_invalid=0 send_seq=3861 receive_seq=3861 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49996998 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=137260 bytes_read=4194524 bytes_retransmit=9 bytes_invalid=0 send_seq=18540 receive_seq=18540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997414 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=79577 bytes_read=1750152 bytes_retransmit=9 bytes_invalid=0 send_seq=10390 receive_seq=10390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997308 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23605 bytes_read=948408 bytes_retransmit=9 bytes_invalid=0 send_seq=3875 receive_seq=3875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997396 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24091 bytes_read=72448 bytes_retransmit=9 bytes_invalid=0 send_seq=3862 receive_seq=3862 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999386 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78183 bytes_read=1553799 bytes_retransmit=0 bytes_invalid=0 send_seq=8421 receive_seq=8421 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999927 adj=31998508 coil_temp=17.3 refs=0 mcu_temp=20.41 supply_voltage=3.012 th0: temp=46.9 th1: temp=46.8 th2: temp=50.1 th3: temp=48.2 sysload=0.32 cputime=290.913 memavail=7395876 print_time=3747.913 buffer_time=2.081 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 77 Hz
Stats 3724.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21361930 bytes_read=2870295 bytes_retransmit=9 bytes_invalid=0 send_seq=380911 receive_seq=380911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=14253 freq=400016090 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23344 bytes_read=73907 bytes_retransmit=0 bytes_invalid=0 send_seq=3862 receive_seq=3862 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997072 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=137336 bytes_read=4197581 bytes_retransmit=9 bytes_invalid=0 send_seq=18551 receive_seq=18551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997472 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=79653 bytes_read=1753266 bytes_retransmit=9 bytes_invalid=0 send_seq=10401 receive_seq=10401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997392 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23611 bytes_read=948642 bytes_retransmit=9 bytes_invalid=0 send_seq=3876 receive_seq=3876 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997518 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24097 bytes_read=72464 bytes_retransmit=9 bytes_invalid=0 send_seq=3863 receive_seq=3863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999403 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78189 bytes_read=1554155 bytes_retransmit=0 bytes_invalid=0 send_seq=8422 receive_seq=8422 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998544 coil_temp=17.3 refs=0 mcu_temp=20.42 supply_voltage=3.012 th0: temp=46.9 th1: temp=46.7 th2: temp=50.2 th3: temp=48.1 sysload=0.32 cputime=291.054 memavail=7395624 print_time=3748.846 buffer_time=2.013 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 78 Hz
Stats 3725.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21375165 bytes_read=2871759 bytes_retransmit=9 bytes_invalid=0 send_seq=381140 receive_seq=381140 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=16267 freq=400016088 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23350 bytes_read=73923 bytes_retransmit=0 bytes_invalid=0 send_seq=3863 receive_seq=3863 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997101 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=137412 bytes_read=4200670 bytes_retransmit=9 bytes_invalid=0 send_seq=18562 receive_seq=18562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997502 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=79729 bytes_read=1756350 bytes_retransmit=9 bytes_invalid=0 send_seq=10412 receive_seq=10412 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997420 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23617 bytes_read=948906 bytes_retransmit=9 bytes_invalid=0 send_seq=3877 receive_seq=3877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997547 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24103 bytes_read=72480 bytes_retransmit=9 bytes_invalid=0 send_seq=3864 receive_seq=3864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999422 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78195 bytes_read=1554511 bytes_retransmit=0 bytes_invalid=0 send_seq=8423 receive_seq=8423 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998564 coil_temp=17.3 refs=0 mcu_temp=20.42 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.7 th2: temp=50.0 th3: temp=48.0 sysload=0.32 cputime=291.212 memavail=7395624 print_time=3750.052 buffer_time=2.220 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 79 Hz
Stats 3726.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21388264 bytes_read=2873243 bytes_retransmit=9 bytes_invalid=0 send_seq=381369 receive_seq=381369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=14465 freq=400016145 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23356 bytes_read=73939 bytes_retransmit=0 bytes_invalid=0 send_seq=3864 receive_seq=3864 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997132 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=137488 bytes_read=4203802 bytes_retransmit=9 bytes_invalid=0 send_seq=18573 receive_seq=18573 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997534 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=79805 bytes_read=1759406 bytes_retransmit=9 bytes_invalid=0 send_seq=10423 receive_seq=10423 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997427 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23623 bytes_read=949170 bytes_retransmit=9 bytes_invalid=0 send_seq=3878 receive_seq=3878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997593 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24109 bytes_read=72496 bytes_retransmit=9 bytes_invalid=0 send_seq=3865 receive_seq=3865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78201 bytes_read=1554867 bytes_retransmit=0 bytes_invalid=0 send_seq=8424 receive_seq=8424 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998585 coil_temp=17.3 refs=0 mcu_temp=20.43 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.9 th2: temp=50.3 th3: temp=47.8 sysload=0.32 cputime=291.357 memavail=7394628 print_time=3750.923 buffer_time=2.088 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 80 Hz
Stats 3727.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21399465 bytes_read=2874533 bytes_retransmit=9 bytes_invalid=0 send_seq=381565 receive_seq=381565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=15251 freq=400016120 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23362 bytes_read=73955 bytes_retransmit=0 bytes_invalid=0 send_seq=3865 receive_seq=3865 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997049 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=137564 bytes_read=4206858 bytes_retransmit=9 bytes_invalid=0 send_seq=18584 receive_seq=18584 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997416 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=79881 bytes_read=1762466 bytes_retransmit=9 bytes_invalid=0 send_seq=10434 receive_seq=10434 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997308 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23629 bytes_read=949419 bytes_retransmit=9 bytes_invalid=0 send_seq=3879 receive_seq=3879 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997503 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24115 bytes_read=72523 bytes_retransmit=9 bytes_invalid=0 send_seq=3866 receive_seq=3866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999406 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78207 bytes_read=1555223 bytes_retransmit=0 bytes_invalid=0 send_seq=8425 receive_seq=8425 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998533 coil_temp=17.3 refs=0 mcu_temp=20.43 supply_voltage=3.012 th0: temp=47.4 th1: temp=46.8 th2: temp=50.3 th3: temp=48.1 sysload=0.32 cputime=291.496 memavail=7394628 print_time=3751.858 buffer_time=2.024 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 81 Hz
Stats 3728.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21413141 bytes_read=2876033 bytes_retransmit=9 bytes_invalid=0 send_seq=381803 receive_seq=381803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=17019 freq=400016113 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23368 bytes_read=73971 bytes_retransmit=0 bytes_invalid=0 send_seq=3866 receive_seq=3866 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997111 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=137640 bytes_read=4209944 bytes_retransmit=9 bytes_invalid=0 send_seq=18595 receive_seq=18595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997478 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=79957 bytes_read=1765568 bytes_retransmit=9 bytes_invalid=0 send_seq=10445 receive_seq=10445 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997469 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23635 bytes_read=949683 bytes_retransmit=9 bytes_invalid=0 send_seq=3880 receive_seq=3880 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997547 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24121 bytes_read=72539 bytes_retransmit=9 bytes_invalid=0 send_seq=3867 receive_seq=3867 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999423 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78213 bytes_read=1555579 bytes_retransmit=0 bytes_invalid=0 send_seq=8426 receive_seq=8426 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998567 coil_temp=17.3 refs=0 mcu_temp=20.42 supply_voltage=3.012 th0: temp=47.2 th1: temp=46.6 th2: temp=50.3 th3: temp=48.3 sysload=0.30 cputime=291.651 memavail=7394636 print_time=3753.063 buffer_time=2.228 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 82 Hz
Stats 3729.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21426520 bytes_read=2877537 bytes_retransmit=9 bytes_invalid=0 send_seq=382036 receive_seq=382036 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=14708 freq=400016104 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23374 bytes_read=74000 bytes_retransmit=0 bytes_invalid=0 send_seq=3867 receive_seq=3867 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997159 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=137716 bytes_read=4213001 bytes_retransmit=9 bytes_invalid=0 send_seq=18606 receive_seq=18606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997523 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=80033 bytes_read=1768625 bytes_retransmit=9 bytes_invalid=0 send_seq=10456 receive_seq=10456 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997485 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23641 bytes_read=949947 bytes_retransmit=9 bytes_invalid=0 send_seq=3881 receive_seq=3881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997573 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24127 bytes_read=72555 bytes_retransmit=9 bytes_invalid=0 send_seq=3868 receive_seq=3868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78219 bytes_read=1555935 bytes_retransmit=0 bytes_invalid=0 send_seq=8427 receive_seq=8427 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998595 coil_temp=17.3 refs=0 mcu_temp=20.42 supply_voltage=3.012 th0: temp=47.4 th1: temp=47.0 th2: temp=50.2 th3: temp=48.3 sysload=0.30 cputime=291.793 memavail=7394636 print_time=3753.935 buffer_time=2.100 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 83 Hz
Stats 3730.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21437958 bytes_read=2878868 bytes_retransmit=9 bytes_invalid=0 send_seq=382237 receive_seq=382237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=15988 freq=400016092 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23380 bytes_read=74016 bytes_retransmit=0 bytes_invalid=0 send_seq=3868 receive_seq=3868 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997177 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=137792 bytes_read=4216058 bytes_retransmit=9 bytes_invalid=0 send_seq=18617 receive_seq=18617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997551 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=80109 bytes_read=1771682 bytes_retransmit=9 bytes_invalid=0 send_seq=10467 receive_seq=10467 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997481 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23647 bytes_read=950181 bytes_retransmit=9 bytes_invalid=0 send_seq=3882 receive_seq=3882 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997583 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24133 bytes_read=72571 bytes_retransmit=9 bytes_invalid=0 send_seq=3869 receive_seq=3869 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78225 bytes_read=1556291 bytes_retransmit=0 bytes_invalid=0 send_seq=8428 receive_seq=8428 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998612 coil_temp=17.3 refs=0 mcu_temp=20.42 supply_voltage=3.012 th0: temp=47.3 th1: temp=46.6 th2: temp=50.3 th3: temp=48.3 sysload=0.30 cputime=291.934 memavail=7394644 print_time=3754.878 buffer_time=2.042 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 84 Hz
Stats 3731.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21451658 bytes_read=2880368 bytes_retransmit=9 bytes_invalid=0 send_seq=382475 receive_seq=382475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=17643 freq=400016070 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23386 bytes_read=74032 bytes_retransmit=0 bytes_invalid=0 send_seq=3869 receive_seq=3869 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997198 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=137868 bytes_read=4219159 bytes_retransmit=9 bytes_invalid=0 send_seq=18628 receive_seq=18628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997572 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=80185 bytes_read=1774768 bytes_retransmit=9 bytes_invalid=0 send_seq=10478 receive_seq=10478 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997488 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23653 bytes_read=950460 bytes_retransmit=9 bytes_invalid=0 send_seq=3883 receive_seq=3883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997604 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24139 bytes_read=72587 bytes_retransmit=9 bytes_invalid=0 send_seq=3870 receive_seq=3870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78231 bytes_read=1556647 bytes_retransmit=0 bytes_invalid=0 send_seq=8429 receive_seq=8429 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998625 coil_temp=17.3 refs=0 mcu_temp=20.42 supply_voltage=3.012 th0: temp=47.3 th1: temp=46.8 th2: temp=50.2 th3: temp=48.2 sysload=0.30 cputime=292.093 memavail=7394644 print_time=3756.070 buffer_time=2.233 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 85 Hz
Stats 3732.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21465307 bytes_read=2881892 bytes_retransmit=9 bytes_invalid=0 send_seq=382712 receive_seq=382712 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=15412 freq=400016048 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23392 bytes_read=74048 bytes_retransmit=0 bytes_invalid=0 send_seq=3870 receive_seq=3870 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997233 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=137944 bytes_read=4222216 bytes_retransmit=9 bytes_invalid=0 send_seq=18639 receive_seq=18639 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997616 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=80261 bytes_read=1777883 bytes_retransmit=9 bytes_invalid=0 send_seq=10489 receive_seq=10489 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23659 bytes_read=950724 bytes_retransmit=9 bytes_invalid=0 send_seq=3884 receive_seq=3884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24145 bytes_read=72614 bytes_retransmit=9 bytes_invalid=0 send_seq=3871 receive_seq=3871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78237 bytes_read=1557003 bytes_retransmit=0 bytes_invalid=0 send_seq=8430 receive_seq=8430 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998645 coil_temp=17.3 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=47.4 th1: temp=46.7 th2: temp=50.5 th3: temp=48.3 sysload=0.30 cputime=292.236 memavail=7394644 print_time=3756.943 buffer_time=2.105 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 86 Hz
Stats 3733.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21476811 bytes_read=2883212 bytes_retransmit=9 bytes_invalid=0 send_seq=382914 receive_seq=382914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=16752 freq=400016046 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23398 bytes_read=74064 bytes_retransmit=0 bytes_invalid=0 send_seq=3871 receive_seq=3871 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997268 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138020 bytes_read=4225330 bytes_retransmit=9 bytes_invalid=0 send_seq=18650 receive_seq=18650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997650 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=80337 bytes_read=1780956 bytes_retransmit=9 bytes_invalid=0 send_seq=10500 receive_seq=10500 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997553 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23665 bytes_read=950958 bytes_retransmit=9 bytes_invalid=0 send_seq=3885 receive_seq=3885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24151 bytes_read=72630 bytes_retransmit=9 bytes_invalid=0 send_seq=3872 receive_seq=3872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999462 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78243 bytes_read=1557359 bytes_retransmit=0 bytes_invalid=0 send_seq=8431 receive_seq=8431 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998662 coil_temp=17.3 refs=0 mcu_temp=20.39 supply_voltage=3.012 th0: temp=47.2 th1: temp=46.8 th2: temp=50.2 th3: temp=48.3 sysload=0.27 cputime=292.380 memavail=7394644 print_time=3757.880 buffer_time=2.042 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 87 Hz
Stats 3734.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21491101 bytes_read=2884742 bytes_retransmit=9 bytes_invalid=0 send_seq=383158 receive_seq=383158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=18305 freq=400016036 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23404 bytes_read=74093 bytes_retransmit=0 bytes_invalid=0 send_seq=3872 receive_seq=3872 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997260 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138096 bytes_read=4228411 bytes_retransmit=9 bytes_invalid=0 send_seq=18661 receive_seq=18661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997636 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=80413 bytes_read=1784039 bytes_retransmit=9 bytes_invalid=0 send_seq=10511 receive_seq=10511 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000086 adj=63997591 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23671 bytes_read=951225 bytes_retransmit=9 bytes_invalid=0 send_seq=3886 receive_seq=3886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24157 bytes_read=72646 bytes_retransmit=9 bytes_invalid=0 send_seq=3873 receive_seq=3873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78249 bytes_read=1557715 bytes_retransmit=0 bytes_invalid=0 send_seq=8432 receive_seq=8432 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998667 coil_temp=17.2 refs=0 mcu_temp=20.38 supply_voltage=3.012 th0: temp=47.4 th1: temp=46.9 th2: temp=50.5 th3: temp=48.3 sysload=0.27 cputime=292.543 memavail=7394408 print_time=3759.079 buffer_time=2.241 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 88 Hz
Stats 3735.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21504968 bytes_read=2886295 bytes_retransmit=9 bytes_invalid=0 send_seq=383398 receive_seq=383398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=15736 freq=400016028 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23410 bytes_read=74109 bytes_retransmit=0 bytes_invalid=0 send_seq=3873 receive_seq=3873 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997258 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138165 bytes_read=4231430 bytes_retransmit=9 bytes_invalid=0 send_seq=18671 receive_seq=18671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997658 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=80489 bytes_read=1787079 bytes_retransmit=9 bytes_invalid=0 send_seq=10522 receive_seq=10522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000082 adj=63997887 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23677 bytes_read=951457 bytes_retransmit=9 bytes_invalid=0 send_seq=3887 receive_seq=3887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24163 bytes_read=72662 bytes_retransmit=9 bytes_invalid=0 send_seq=3874 receive_seq=3874 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78255 bytes_read=1558071 bytes_retransmit=0 bytes_invalid=0 send_seq=8433 receive_seq=8433 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998666 coil_temp=17.2 refs=0 mcu_temp=20.38 supply_voltage=3.012 th0: temp=47.3 th1: temp=46.9 th2: temp=50.4 th3: temp=48.3 sysload=0.27 cputime=292.689 memavail=7394412 print_time=3759.948 buffer_time=2.109 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 89 Hz
Stats 3736.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21516658 bytes_read=2887628 bytes_retransmit=9 bytes_invalid=0 send_seq=383603 receive_seq=383603 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=17028 freq=400016016 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23416 bytes_read=74125 bytes_retransmit=0 bytes_invalid=0 send_seq=3874 receive_seq=3874 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997266 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138241 bytes_read=4234485 bytes_retransmit=9 bytes_invalid=0 send_seq=18682 receive_seq=18682 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997720 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=80558 bytes_read=1790096 bytes_retransmit=9 bytes_invalid=0 send_seq=10532 receive_seq=10532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000079 adj=63997820 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23683 bytes_read=951673 bytes_retransmit=9 bytes_invalid=0 send_seq=3888 receive_seq=3888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24169 bytes_read=72678 bytes_retransmit=9 bytes_invalid=0 send_seq=3875 receive_seq=3875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78261 bytes_read=1558427 bytes_retransmit=0 bytes_invalid=0 send_seq=8434 receive_seq=8434 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998673 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.012 th0: temp=47.3 th1: temp=46.7 th2: temp=50.2 th3: temp=48.2 sysload=0.27 cputime=292.845 memavail=7395032 print_time=3760.881 buffer_time=2.042 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 90 Hz
Stats 3737.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21531180 bytes_read=2889198 bytes_retransmit=9 bytes_invalid=0 send_seq=383855 receive_seq=383855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=18621 freq=400016003 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23422 bytes_read=74141 bytes_retransmit=0 bytes_invalid=0 send_seq=3875 receive_seq=3875 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997275 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138317 bytes_read=4237550 bytes_retransmit=9 bytes_invalid=0 send_seq=18693 receive_seq=18693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997728 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=80634 bytes_read=1793165 bytes_retransmit=9 bytes_invalid=0 send_seq=10543 receive_seq=10543 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000078 adj=63997759 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23689 bytes_read=951948 bytes_retransmit=9 bytes_invalid=0 send_seq=3889 receive_seq=3889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997669 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24175 bytes_read=72705 bytes_retransmit=9 bytes_invalid=0 send_seq=3876 receive_seq=3876 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78267 bytes_read=1558783 bytes_retransmit=0 bytes_invalid=0 send_seq=8435 receive_seq=8435 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998686 coil_temp=17.2 refs=0 mcu_temp=20.36 supply_voltage=3.012 th0: temp=47.3 th1: temp=47.0 th2: temp=50.4 th3: temp=48.3 sysload=0.27 cputime=293.008 memavail=7395032 print_time=3762.088 buffer_time=2.248 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 91 Hz
Stats 3738.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21545188 bytes_read=2890737 bytes_retransmit=9 bytes_invalid=0 send_seq=384095 receive_seq=384095 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=16061 freq=400015997 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23428 bytes_read=74157 bytes_retransmit=0 bytes_invalid=0 send_seq=3876 receive_seq=3876 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997266 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138393 bytes_read=4240593 bytes_retransmit=9 bytes_invalid=0 send_seq=18704 receive_seq=18704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997713 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=80710 bytes_read=1796223 bytes_retransmit=9 bytes_invalid=0 send_seq=10554 receive_seq=10554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000075 adj=63997700 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23695 bytes_read=952180 bytes_retransmit=9 bytes_invalid=0 send_seq=3890 receive_seq=3890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997669 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24181 bytes_read=72721 bytes_retransmit=9 bytes_invalid=0 send_seq=3877 receive_seq=3877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999462 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78273 bytes_read=1559139 bytes_retransmit=0 bytes_invalid=0 send_seq=8436 receive_seq=8436 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998687 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=47.2 th1: temp=46.5 th2: temp=50.4 th3: temp=48.4 sysload=0.25 cputime=293.153 memavail=7395032 print_time=3762.963 buffer_time=2.123 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 92 Hz
Stats 3739.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21556987 bytes_read=2892062 bytes_retransmit=9 bytes_invalid=0 send_seq=384298 receive_seq=384298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=17856 freq=400016000 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23434 bytes_read=74186 bytes_retransmit=0 bytes_invalid=0 send_seq=3877 receive_seq=3877 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997270 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138469 bytes_read=4243650 bytes_retransmit=9 bytes_invalid=0 send_seq=18715 receive_seq=18715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997803 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=80786 bytes_read=1799336 bytes_retransmit=9 bytes_invalid=0 send_seq=10565 receive_seq=10565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997654 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23701 bytes_read=952398 bytes_retransmit=9 bytes_invalid=0 send_seq=3891 receive_seq=3891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24187 bytes_read=72737 bytes_retransmit=9 bytes_invalid=0 send_seq=3878 receive_seq=3878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78279 bytes_read=1559495 bytes_retransmit=0 bytes_invalid=0 send_seq=8437 receive_seq=8437 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999926 adj=31998688 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.8 th2: temp=50.2 th3: temp=48.3 sysload=0.25 cputime=293.297 memavail=7394788 print_time=3763.899 buffer_time=2.057 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 93 Hz
Stats 3740.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21571559 bytes_read=2893628 bytes_retransmit=9 bytes_invalid=0 send_seq=384546 receive_seq=384546 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=19560 freq=400015994 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23440 bytes_read=74202 bytes_retransmit=0 bytes_invalid=0 send_seq=3878 receive_seq=3878 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997259 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138545 bytes_read=4246795 bytes_retransmit=9 bytes_invalid=0 send_seq=18726 receive_seq=18726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997761 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=80862 bytes_read=1802420 bytes_retransmit=9 bytes_invalid=0 send_seq=10576 receive_seq=10576 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997602 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23707 bytes_read=952674 bytes_retransmit=9 bytes_invalid=0 send_seq=3892 receive_seq=3892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24193 bytes_read=72753 bytes_retransmit=9 bytes_invalid=0 send_seq=3879 receive_seq=3879 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999459 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78285 bytes_read=1559851 bytes_retransmit=0 bytes_invalid=0 send_seq=8438 receive_seq=8438 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998684 coil_temp=17.2 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=47.2 th1: temp=47.0 th2: temp=50.4 th3: temp=48.3 sysload=0.25 cputime=293.461 memavail=7394788 print_time=3765.096 buffer_time=2.253 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 94 Hz
Stats 3741.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21585986 bytes_read=2895212 bytes_retransmit=9 bytes_invalid=0 send_seq=384795 receive_seq=384795 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=16592 freq=400015989 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23446 bytes_read=74218 bytes_retransmit=0 bytes_invalid=0 send_seq=3879 receive_seq=3879 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997254 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138621 bytes_read=4249870 bytes_retransmit=9 bytes_invalid=0 send_seq=18737 receive_seq=18737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997806 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=80938 bytes_read=1805478 bytes_retransmit=9 bytes_invalid=0 send_seq=10587 receive_seq=10587 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23713 bytes_read=952923 bytes_retransmit=9 bytes_invalid=0 send_seq=3893 receive_seq=3893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24199 bytes_read=72769 bytes_retransmit=9 bytes_invalid=0 send_seq=3880 receive_seq=3880 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78291 bytes_read=1560207 bytes_retransmit=0 bytes_invalid=0 send_seq=8439 receive_seq=8439 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998745 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.8 th2: temp=50.4 th3: temp=48.4 sysload=0.25 cputime=293.612 memavail=7394800 print_time=3765.967 buffer_time=2.123 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 95 Hz
Stats 3742.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21598043 bytes_read=2896572 bytes_retransmit=9 bytes_invalid=0 send_seq=385005 receive_seq=385005 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=18412 freq=400015990 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23452 bytes_read=74234 bytes_retransmit=0 bytes_invalid=0 send_seq=3880 receive_seq=3880 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997256 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138697 bytes_read=4252928 bytes_retransmit=9 bytes_invalid=0 send_seq=18748 receive_seq=18748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997796 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=81014 bytes_read=1808537 bytes_retransmit=9 bytes_invalid=0 send_seq=10598 receive_seq=10598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23719 bytes_read=953172 bytes_retransmit=9 bytes_invalid=0 send_seq=3894 receive_seq=3894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24205 bytes_read=72796 bytes_retransmit=9 bytes_invalid=0 send_seq=3881 receive_seq=3881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999455 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78297 bytes_read=1560563 bytes_retransmit=0 bytes_invalid=0 send_seq=8440 receive_seq=8440 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998735 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.9 th2: temp=50.5 th3: temp=48.6 sysload=0.25 cputime=293.756 memavail=7394800 print_time=3766.905 buffer_time=2.060 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 96 Hz
Stats 3743.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21612947 bytes_read=2898167 bytes_retransmit=9 bytes_invalid=0 send_seq=385262 receive_seq=385262 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=20016 freq=400015981 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23458 bytes_read=74250 bytes_retransmit=0 bytes_invalid=0 send_seq=3881 receive_seq=3881 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997249 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138773 bytes_read=4256015 bytes_retransmit=9 bytes_invalid=0 send_seq=18759 receive_seq=18759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997749 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=81090 bytes_read=1811639 bytes_retransmit=9 bytes_invalid=0 send_seq=10609 receive_seq=10609 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997484 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23725 bytes_read=953451 bytes_retransmit=9 bytes_invalid=0 send_seq=3895 receive_seq=3895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24211 bytes_read=72812 bytes_retransmit=9 bytes_invalid=0 send_seq=3882 receive_seq=3882 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78303 bytes_read=1560919 bytes_retransmit=0 bytes_invalid=0 send_seq=8441 receive_seq=8441 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998729 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.9 th2: temp=50.2 th3: temp=48.3 sysload=0.23 cputime=293.924 memavail=7394800 print_time=3768.108 buffer_time=2.263 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 97 Hz
Stats 3744.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21627594 bytes_read=2899766 bytes_retransmit=9 bytes_invalid=0 send_seq=385514 receive_seq=385514 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=16760 freq=400015970 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23464 bytes_read=74279 bytes_retransmit=0 bytes_invalid=0 send_seq=3882 receive_seq=3882 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997255 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138849 bytes_read=4259073 bytes_retransmit=9 bytes_invalid=0 send_seq=18770 receive_seq=18770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997850 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=81166 bytes_read=1814696 bytes_retransmit=9 bytes_invalid=0 send_seq=10620 receive_seq=10620 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997481 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23731 bytes_read=953700 bytes_retransmit=9 bytes_invalid=0 send_seq=3896 receive_seq=3896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24217 bytes_read=72828 bytes_retransmit=9 bytes_invalid=0 send_seq=3883 receive_seq=3883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78309 bytes_read=1561275 bytes_retransmit=0 bytes_invalid=0 send_seq=8442 receive_seq=8442 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998707 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=47.4 th1: temp=47.0 th2: temp=50.3 th3: temp=48.4 sysload=0.23 cputime=294.075 memavail=7394808 print_time=3768.976 buffer_time=2.131 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 98 Hz
Stats 3745.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21639717 bytes_read=2901152 bytes_retransmit=9 bytes_invalid=0 send_seq=385726 receive_seq=385726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=18760 freq=400015961 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23470 bytes_read=74295 bytes_retransmit=0 bytes_invalid=0 send_seq=3883 receive_seq=3883 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997268 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138925 bytes_read=4262132 bytes_retransmit=9 bytes_invalid=0 send_seq=18781 receive_seq=18781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997822 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=81242 bytes_read=1817753 bytes_retransmit=9 bytes_invalid=0 send_seq=10631 receive_seq=10631 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997478 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23737 bytes_read=953934 bytes_retransmit=9 bytes_invalid=0 send_seq=3897 receive_seq=3897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997703 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24223 bytes_read=72844 bytes_retransmit=9 bytes_invalid=0 send_seq=3884 receive_seq=3884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78315 bytes_read=1561631 bytes_retransmit=0 bytes_invalid=0 send_seq=8443 receive_seq=8443 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998712 coil_temp=17.2 refs=0 mcu_temp=20.36 supply_voltage=3.012 th0: temp=47.4 th1: temp=47.0 th2: temp=50.4 th3: temp=48.4 sysload=0.23 cputime=294.225 memavail=7394808 print_time=3769.908 buffer_time=2.062 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 99 Hz
Stats 3746.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21654774 bytes_read=2902760 bytes_retransmit=9 bytes_invalid=0 send_seq=385986 receive_seq=385986 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=20651 freq=400015945 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23476 bytes_read=74311 bytes_retransmit=0 bytes_invalid=0 send_seq=3884 receive_seq=3884 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997273 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139001 bytes_read=4265234 bytes_retransmit=9 bytes_invalid=0 send_seq=18792 receive_seq=18792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997858 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=81318 bytes_read=1820898 bytes_retransmit=9 bytes_invalid=0 send_seq=10642 receive_seq=10642 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997473 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23743 bytes_read=954213 bytes_retransmit=9 bytes_invalid=0 send_seq=3898 receive_seq=3898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997704 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24229 bytes_read=72860 bytes_retransmit=9 bytes_invalid=0 send_seq=3885 receive_seq=3885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78321 bytes_read=1561987 bytes_retransmit=0 bytes_invalid=0 send_seq=8444 receive_seq=8444 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998713 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.012 th0: temp=47.5 th1: temp=47.4 th2: temp=50.5 th3: temp=48.4 sysload=0.23 cputime=294.394 memavail=7394324 print_time=3771.108 buffer_time=2.262 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 100 Hz
Stats 3747.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21669705 bytes_read=2904387 bytes_retransmit=9 bytes_invalid=0 send_seq=386244 receive_seq=386244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=17456 freq=400015946 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23482 bytes_read=74327 bytes_retransmit=0 bytes_invalid=0 send_seq=3885 receive_seq=3885 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997279 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139070 bytes_read=4268268 bytes_retransmit=9 bytes_invalid=0 send_seq=18802 receive_seq=18802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997805 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=81394 bytes_read=1823954 bytes_retransmit=9 bytes_invalid=0 send_seq=10653 receive_seq=10653 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997489 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23749 bytes_read=954477 bytes_retransmit=9 bytes_invalid=0 send_seq=3899 receive_seq=3899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997702 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24235 bytes_read=72887 bytes_retransmit=9 bytes_invalid=0 send_seq=3886 receive_seq=3886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78327 bytes_read=1562343 bytes_retransmit=0 bytes_invalid=0 send_seq=8445 receive_seq=8445 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998703 coil_temp=17.2 refs=0 mcu_temp=20.38 supply_voltage=3.012 th0: temp=47.4 th1: temp=47.1 th2: temp=50.4 th3: temp=48.5 sysload=0.23 cputime=294.545 memavail=7394072 print_time=3771.977 buffer_time=2.131 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 101 Hz
Stats 3748.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21682206 bytes_read=2905782 bytes_retransmit=9 bytes_invalid=0 send_seq=386462 receive_seq=386461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=19264 freq=400015942 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23488 bytes_read=74343 bytes_retransmit=0 bytes_invalid=0 send_seq=3886 receive_seq=3886 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997271 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139146 bytes_read=4271382 bytes_retransmit=9 bytes_invalid=0 send_seq=18813 receive_seq=18813 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997761 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=81463 bytes_read=1827005 bytes_retransmit=9 bytes_invalid=0 send_seq=10663 receive_seq=10663 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997478 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23755 bytes_read=954711 bytes_retransmit=9 bytes_invalid=0 send_seq=3900 receive_seq=3900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997770 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24241 bytes_read=72903 bytes_retransmit=9 bytes_invalid=0 send_seq=3887 receive_seq=3887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78333 bytes_read=1562683 bytes_retransmit=0 bytes_invalid=0 send_seq=8446 receive_seq=8446 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998693 coil_temp=17.2 refs=0 mcu_temp=20.38 supply_voltage=3.012 th0: temp=47.6 th1: temp=47.0 th2: temp=50.5 th3: temp=48.5 sysload=0.29 cputime=294.693 memavail=7394072 print_time=3772.916 buffer_time=2.068 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 102 Hz
Stats 3749.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21697569 bytes_read=2907431 bytes_retransmit=9 bytes_invalid=0 send_seq=386726 receive_seq=386726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=21146 freq=400015934 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23494 bytes_read=74372 bytes_retransmit=0 bytes_invalid=0 send_seq=3887 receive_seq=3887 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997272 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139222 bytes_read=4274467 bytes_retransmit=9 bytes_invalid=0 send_seq=18824 receive_seq=18824 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997728 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=81539 bytes_read=1830091 bytes_retransmit=9 bytes_invalid=0 send_seq=10674 receive_seq=10674 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997470 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23761 bytes_read=955005 bytes_retransmit=9 bytes_invalid=0 send_seq=3901 receive_seq=3901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997755 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24247 bytes_read=72919 bytes_retransmit=9 bytes_invalid=0 send_seq=3888 receive_seq=3888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78339 bytes_read=1563039 bytes_retransmit=0 bytes_invalid=0 send_seq=8447 receive_seq=8447 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998686 coil_temp=17.2 refs=0 mcu_temp=20.38 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.2 th2: temp=50.7 th3: temp=48.5 sysload=0.29 cputime=294.868 memavail=7394072 print_time=3774.117 buffer_time=2.269 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 103 Hz
Stats 3750.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21712475 bytes_read=2909057 bytes_retransmit=9 bytes_invalid=0 send_seq=386983 receive_seq=386983 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=18096 freq=400015924 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23500 bytes_read=74388 bytes_retransmit=0 bytes_invalid=0 send_seq=3888 receive_seq=3888 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997265 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139298 bytes_read=4277524 bytes_retransmit=9 bytes_invalid=0 send_seq=18835 receive_seq=18835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997726 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=81615 bytes_read=1833147 bytes_retransmit=9 bytes_invalid=0 send_seq=10685 receive_seq=10685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23767 bytes_read=955239 bytes_retransmit=9 bytes_invalid=0 send_seq=3902 receive_seq=3902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997722 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24253 bytes_read=72935 bytes_retransmit=9 bytes_invalid=0 send_seq=3889 receive_seq=3889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78345 bytes_read=1563395 bytes_retransmit=0 bytes_invalid=0 send_seq=8448 receive_seq=8448 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998678 coil_temp=17.2 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=47.5 th1: temp=46.9 th2: temp=50.3 th3: temp=48.5 sysload=0.29 cputime=295.029 memavail=7394072 print_time=3774.988 buffer_time=2.140 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 104 Hz
Stats 3751.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21725343 bytes_read=2910492 bytes_retransmit=9 bytes_invalid=0 send_seq=387208 receive_seq=387208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=20104 freq=400015903 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23506 bytes_read=74404 bytes_retransmit=0 bytes_invalid=0 send_seq=3889 receive_seq=3889 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997276 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139374 bytes_read=4280599 bytes_retransmit=9 bytes_invalid=0 send_seq=18846 receive_seq=18846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997720 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=81691 bytes_read=1836206 bytes_retransmit=9 bytes_invalid=0 send_seq=10696 receive_seq=10696 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23773 bytes_read=955473 bytes_retransmit=9 bytes_invalid=0 send_seq=3903 receive_seq=3903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997720 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24259 bytes_read=72951 bytes_retransmit=9 bytes_invalid=0 send_seq=3890 receive_seq=3890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78351 bytes_read=1563751 bytes_retransmit=0 bytes_invalid=0 send_seq=8449 receive_seq=8449 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998698 coil_temp=17.2 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.1 th2: temp=50.6 th3: temp=48.5 sysload=0.29 cputime=295.189 memavail=7394072 print_time=3775.918 buffer_time=2.070 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 105 Hz
Stats 3752.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21741005 bytes_read=2912161 bytes_retransmit=9 bytes_invalid=0 send_seq=387477 receive_seq=387477 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=22080 freq=400015898 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23512 bytes_read=74420 bytes_retransmit=0 bytes_invalid=0 send_seq=3890 receive_seq=3890 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997293 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139450 bytes_read=4283683 bytes_retransmit=9 bytes_invalid=0 send_seq=18857 receive_seq=18857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997731 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=81767 bytes_read=1839291 bytes_retransmit=9 bytes_invalid=0 send_seq=10707 receive_seq=10707 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23779 bytes_read=955782 bytes_retransmit=9 bytes_invalid=0 send_seq=3904 receive_seq=3904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997779 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24265 bytes_read=72978 bytes_retransmit=9 bytes_invalid=0 send_seq=3891 receive_seq=3891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78357 bytes_read=1564107 bytes_retransmit=0 bytes_invalid=0 send_seq=8450 receive_seq=8450 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998711 coil_temp=17.2 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=47.8 th1: temp=47.1 th2: temp=50.6 th3: temp=48.4 sysload=0.29 cputime=295.373 memavail=7394072 print_time=3777.123 buffer_time=2.275 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 106 Hz
Stats 3753.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21756504 bytes_read=2913816 bytes_retransmit=9 bytes_invalid=0 send_seq=387743 receive_seq=387743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=18388 freq=400015912 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23518 bytes_read=74436 bytes_retransmit=0 bytes_invalid=0 send_seq=3891 receive_seq=3891 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997278 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139526 bytes_read=4286741 bytes_retransmit=9 bytes_invalid=0 send_seq=18868 receive_seq=18868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997701 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=81843 bytes_read=1842367 bytes_retransmit=9 bytes_invalid=0 send_seq=10718 receive_seq=10718 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997517 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23785 bytes_read=956016 bytes_retransmit=9 bytes_invalid=0 send_seq=3905 receive_seq=3905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997769 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24271 bytes_read=72994 bytes_retransmit=9 bytes_invalid=0 send_seq=3892 receive_seq=3892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78363 bytes_read=1564463 bytes_retransmit=0 bytes_invalid=0 send_seq=8451 receive_seq=8451 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998696 coil_temp=17.2 refs=0 mcu_temp=20.38 supply_voltage=3.012 th0: temp=47.3 th1: temp=47.3 th2: temp=50.7 th3: temp=48.8 sysload=0.35 cputime=295.555 memavail=7393396 print_time=3777.983 buffer_time=2.135 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 107 Hz
Stats 3754.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21769515 bytes_read=2915266 bytes_retransmit=9 bytes_invalid=0 send_seq=387971 receive_seq=387971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=20472 freq=400015910 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23524 bytes_read=74465 bytes_retransmit=0 bytes_invalid=0 send_seq=3892 receive_seq=3892 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997263 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139602 bytes_read=4289797 bytes_retransmit=9 bytes_invalid=0 send_seq=18879 receive_seq=18879 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997661 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=81919 bytes_read=1845485 bytes_retransmit=9 bytes_invalid=0 send_seq=10729 receive_seq=10729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997479 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23791 bytes_read=956250 bytes_retransmit=9 bytes_invalid=0 send_seq=3906 receive_seq=3906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997723 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24277 bytes_read=73010 bytes_retransmit=9 bytes_invalid=0 send_seq=3893 receive_seq=3893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78369 bytes_read=1564819 bytes_retransmit=0 bytes_invalid=0 send_seq=8452 receive_seq=8452 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998674 coil_temp=17.2 refs=0 mcu_temp=20.38 supply_voltage=3.012 th0: temp=47.6 th1: temp=47.1 th2: temp=50.6 th3: temp=48.5 sysload=0.35 cputime=295.709 memavail=7393148 print_time=3778.921 buffer_time=2.072 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 108 Hz
Stats 3755.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21785393 bytes_read=2916971 bytes_retransmit=9 bytes_invalid=0 send_seq=388244 receive_seq=388244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=22416 freq=400015909 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23530 bytes_read=74481 bytes_retransmit=0 bytes_invalid=0 send_seq=3893 receive_seq=3893 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997261 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139678 bytes_read=4292943 bytes_retransmit=9 bytes_invalid=0 send_seq=18890 receive_seq=18890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997685 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=81995 bytes_read=1848570 bytes_retransmit=9 bytes_invalid=0 send_seq=10740 receive_seq=10740 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997472 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23797 bytes_read=956544 bytes_retransmit=9 bytes_invalid=0 send_seq=3907 receive_seq=3907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997732 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24283 bytes_read=73026 bytes_retransmit=9 bytes_invalid=0 send_seq=3894 receive_seq=3894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78375 bytes_read=1565175 bytes_retransmit=0 bytes_invalid=0 send_seq=8453 receive_seq=8453 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998674 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.012 th0: temp=47.6 th1: temp=47.0 th2: temp=50.6 th3: temp=48.3 sysload=0.35 cputime=295.885 memavail=7393148 print_time=3780.120 buffer_time=2.270 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 109 Hz
Stats 3756.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21801159 bytes_read=2918661 bytes_retransmit=9 bytes_invalid=0 send_seq=388517 receive_seq=388517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=18952 freq=400015902 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23536 bytes_read=74497 bytes_retransmit=0 bytes_invalid=0 send_seq=3894 receive_seq=3894 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997252 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139754 bytes_read=4296016 bytes_retransmit=9 bytes_invalid=0 send_seq=18901 receive_seq=18901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997689 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=82071 bytes_read=1851626 bytes_retransmit=9 bytes_invalid=0 send_seq=10751 receive_seq=10751 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997482 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23803 bytes_read=956778 bytes_retransmit=9 bytes_invalid=0 send_seq=3908 receive_seq=3908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997702 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24289 bytes_read=73042 bytes_retransmit=9 bytes_invalid=0 send_seq=3895 receive_seq=3895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78381 bytes_read=1565531 bytes_retransmit=0 bytes_invalid=0 send_seq=8454 receive_seq=8454 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998668 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.012 th0: temp=47.6 th1: temp=46.9 th2: temp=50.4 th3: temp=48.7 sysload=0.35 cputime=296.049 memavail=7392404 print_time=3781.000 buffer_time=2.149 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 110 Hz
Stats 3757.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21814192 bytes_read=2920097 bytes_retransmit=9 bytes_invalid=0 send_seq=388743 receive_seq=388743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=21316 freq=400015901 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23542 bytes_read=74513 bytes_retransmit=0 bytes_invalid=0 send_seq=3895 receive_seq=3895 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997261 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139823 bytes_read=4299050 bytes_retransmit=9 bytes_invalid=0 send_seq=18911 receive_seq=18911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997697 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=82147 bytes_read=1854682 bytes_retransmit=9 bytes_invalid=0 send_seq=10762 receive_seq=10762 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23809 bytes_read=957027 bytes_retransmit=9 bytes_invalid=0 send_seq=3909 receive_seq=3909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24295 bytes_read=73069 bytes_retransmit=9 bytes_invalid=0 send_seq=3896 receive_seq=3896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78387 bytes_read=1565887 bytes_retransmit=0 bytes_invalid=0 send_seq=8455 receive_seq=8455 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998677 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.012 th0: temp=47.7 th1: temp=46.8 th2: temp=50.6 th3: temp=48.6 sysload=0.35 cputime=296.225 memavail=7392328 print_time=3781.927 buffer_time=2.076 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 111 Hz
Stats 3758.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21830531 bytes_read=2921821 bytes_retransmit=9 bytes_invalid=0 send_seq=389023 receive_seq=389023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=22996 freq=400015905 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23548 bytes_read=74529 bytes_retransmit=0 bytes_invalid=0 send_seq=3896 receive_seq=3896 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997247 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139899 bytes_read=4302135 bytes_retransmit=9 bytes_invalid=0 send_seq=18922 receive_seq=18922 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997694 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=82216 bytes_read=1857762 bytes_retransmit=9 bytes_invalid=0 send_seq=10772 receive_seq=10772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997499 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23815 bytes_read=957321 bytes_retransmit=9 bytes_invalid=0 send_seq=3910 receive_seq=3910 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997689 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24301 bytes_read=73085 bytes_retransmit=9 bytes_invalid=0 send_seq=3897 receive_seq=3897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78393 bytes_read=1566243 bytes_retransmit=0 bytes_invalid=0 send_seq=8456 receive_seq=8456 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998667 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.012 th0: temp=47.8 th1: temp=47.1 th2: temp=50.6 th3: temp=48.6 sysload=0.32 cputime=296.408 memavail=7392412 print_time=3783.126 buffer_time=2.273 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 112 Hz
Stats 3759.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21846592 bytes_read=2923516 bytes_retransmit=9 bytes_invalid=0 send_seq=389297 receive_seq=389297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=19108 freq=400015891 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23554 bytes_read=74558 bytes_retransmit=0 bytes_invalid=0 send_seq=3897 receive_seq=3897 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997234 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139975 bytes_read=4305192 bytes_retransmit=9 bytes_invalid=0 send_seq=18933 receive_seq=18933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997679 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=82292 bytes_read=1860819 bytes_retransmit=9 bytes_invalid=0 send_seq=10783 receive_seq=10783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997493 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23821 bytes_read=957555 bytes_retransmit=9 bytes_invalid=0 send_seq=3911 receive_seq=3911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997736 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24307 bytes_read=73101 bytes_retransmit=9 bytes_invalid=0 send_seq=3898 receive_seq=3898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78399 bytes_read=1566599 bytes_retransmit=0 bytes_invalid=0 send_seq=8457 receive_seq=8457 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998659 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.012 th0: temp=47.5 th1: temp=47.1 th2: temp=50.8 th3: temp=48.8 sysload=0.32 cputime=296.574 memavail=7392412 print_time=3783.998 buffer_time=2.144 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 113 Hz
Stats 3760.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21859959 bytes_read=2925002 bytes_retransmit=9 bytes_invalid=0 send_seq=389529 receive_seq=389529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=21272 freq=400015886 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23560 bytes_read=74574 bytes_retransmit=0 bytes_invalid=0 send_seq=3898 receive_seq=3898 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997270 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140051 bytes_read=4308248 bytes_retransmit=9 bytes_invalid=0 send_seq=18944 receive_seq=18944 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997708 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=82368 bytes_read=1863878 bytes_retransmit=9 bytes_invalid=0 send_seq=10794 receive_seq=10794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997507 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23827 bytes_read=957789 bytes_retransmit=9 bytes_invalid=0 send_seq=3912 receive_seq=3912 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997742 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24313 bytes_read=73117 bytes_retransmit=9 bytes_invalid=0 send_seq=3899 receive_seq=3899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78405 bytes_read=1566955 bytes_retransmit=0 bytes_invalid=0 send_seq=8458 receive_seq=8458 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998667 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.1 th2: temp=50.7 th3: temp=48.6 sysload=0.32 cputime=296.732 memavail=7392416 print_time=3784.936 buffer_time=2.082 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 114 Hz
Stats 3761.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21876290 bytes_read=2926731 bytes_retransmit=9 bytes_invalid=0 send_seq=389810 receive_seq=389810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=23124 freq=400015889 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23566 bytes_read=74590 bytes_retransmit=0 bytes_invalid=0 send_seq=3899 receive_seq=3899 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997271 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140127 bytes_read=4311350 bytes_retransmit=9 bytes_invalid=0 send_seq=18955 receive_seq=18955 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997690 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=82444 bytes_read=1867021 bytes_retransmit=9 bytes_invalid=0 send_seq=10805 receive_seq=10805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997525 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23833 bytes_read=958083 bytes_retransmit=9 bytes_invalid=0 send_seq=3913 receive_seq=3913 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997721 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24319 bytes_read=73133 bytes_retransmit=9 bytes_invalid=0 send_seq=3900 receive_seq=3900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78411 bytes_read=1567311 bytes_retransmit=0 bytes_invalid=0 send_seq=8459 receive_seq=8459 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998677 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.012 th0: temp=48.0 th1: temp=47.2 th2: temp=50.5 th3: temp=48.6 sysload=0.32 cputime=296.992 memavail=7392416 print_time=3786.133 buffer_time=2.279 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 115 Hz
Stats 3762.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21892292 bytes_read=2928426 bytes_retransmit=9 bytes_invalid=0 send_seq=390084 receive_seq=390084 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=43 upcoming_bytes=19689 freq=400015880 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23572 bytes_read=74606 bytes_retransmit=0 bytes_invalid=0 send_seq=3900 receive_seq=3900 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997255 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140203 bytes_read=4314467 bytes_retransmit=9 bytes_invalid=0 send_seq=18966 receive_seq=18966 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997740 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=82520 bytes_read=1870079 bytes_retransmit=9 bytes_invalid=0 send_seq=10816 receive_seq=10816 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997502 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23839 bytes_read=958332 bytes_retransmit=9 bytes_invalid=0 send_seq=3914 receive_seq=3914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997682 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24325 bytes_read=73160 bytes_retransmit=9 bytes_invalid=0 send_seq=3901 receive_seq=3901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78417 bytes_read=1567667 bytes_retransmit=0 bytes_invalid=0 send_seq=8460 receive_seq=8460 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998674 coil_temp=17.2 refs=0 mcu_temp=20.38 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.4 th2: temp=50.9 th3: temp=48.6 sysload=0.32 cputime=297.155 memavail=7392416 print_time=3787.004 buffer_time=2.150 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 116 Hz
Stats 3763.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21905612 bytes_read=2929901 bytes_retransmit=9 bytes_invalid=0 send_seq=390317 receive_seq=390317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=22216 freq=400015866 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23578 bytes_read=74622 bytes_retransmit=0 bytes_invalid=0 send_seq=3901 receive_seq=3901 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997265 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140279 bytes_read=4317524 bytes_retransmit=9 bytes_invalid=0 send_seq=18977 receive_seq=18977 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997741 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=82596 bytes_read=1873153 bytes_retransmit=9 bytes_invalid=0 send_seq=10827 receive_seq=10827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23845 bytes_read=958566 bytes_retransmit=9 bytes_invalid=0 send_seq=3915 receive_seq=3915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24331 bytes_read=73176 bytes_retransmit=9 bytes_invalid=0 send_seq=3902 receive_seq=3902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78423 bytes_read=1568023 bytes_retransmit=0 bytes_invalid=0 send_seq=8461 receive_seq=8461 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998676 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.1 th2: temp=50.7 th3: temp=48.7 sysload=0.38 cputime=297.313 memavail=7392416 print_time=3787.940 buffer_time=2.084 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 117 Hz
Stats 3764.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21922464 bytes_read=2931670 bytes_retransmit=9 bytes_invalid=0 send_seq=390606 receive_seq=390606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=23608 freq=400015883 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23584 bytes_read=74651 bytes_retransmit=0 bytes_invalid=0 send_seq=3902 receive_seq=3902 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997280 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140355 bytes_read=4320609 bytes_retransmit=9 bytes_invalid=0 send_seq=18988 receive_seq=18988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997886 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=82672 bytes_read=1876239 bytes_retransmit=9 bytes_invalid=0 send_seq=10838 receive_seq=10838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23851 bytes_read=958860 bytes_retransmit=9 bytes_invalid=0 send_seq=3916 receive_seq=3916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997715 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24337 bytes_read=73192 bytes_retransmit=9 bytes_invalid=0 send_seq=3903 receive_seq=3903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78429 bytes_read=1568379 bytes_retransmit=0 bytes_invalid=0 send_seq=8462 receive_seq=8462 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998683 coil_temp=17.2 refs=0 mcu_temp=20.36 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.3 th2: temp=50.8 th3: temp=48.7 sysload=0.38 cputime=297.493 memavail=7392416 print_time=3789.139 buffer_time=2.282 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 118 Hz
Stats 3765.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21938908 bytes_read=2933426 bytes_retransmit=9 bytes_invalid=0 send_seq=390889 receive_seq=390889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=19864 freq=400015879 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23590 bytes_read=74667 bytes_retransmit=0 bytes_invalid=0 send_seq=3903 receive_seq=3903 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997240 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140424 bytes_read=4323642 bytes_retransmit=9 bytes_invalid=0 send_seq=18998 receive_seq=18998 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997865 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=82741 bytes_read=1879273 bytes_retransmit=9 bytes_invalid=0 send_seq=10848 receive_seq=10848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997512 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23857 bytes_read=959094 bytes_retransmit=9 bytes_invalid=0 send_seq=3917 receive_seq=3917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24343 bytes_read=73208 bytes_retransmit=9 bytes_invalid=0 send_seq=3904 receive_seq=3904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78435 bytes_read=1568735 bytes_retransmit=0 bytes_invalid=0 send_seq=8463 receive_seq=8463 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998704 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.012 th0: temp=47.8 th1: temp=47.2 th2: temp=50.8 th3: temp=48.9 sysload=0.38 cputime=297.655 memavail=7392416 print_time=3790.015 buffer_time=2.158 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 119 Hz
Stats 3766.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21952461 bytes_read=2934916 bytes_retransmit=9 bytes_invalid=0 send_seq=391125 receive_seq=391125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=22148 freq=400015866 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23596 bytes_read=74683 bytes_retransmit=0 bytes_invalid=0 send_seq=3904 receive_seq=3904 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997242 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140500 bytes_read=4326716 bytes_retransmit=9 bytes_invalid=0 send_seq=19009 receive_seq=19009 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997819 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=82817 bytes_read=1882329 bytes_retransmit=9 bytes_invalid=0 send_seq=10859 receive_seq=10859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23863 bytes_read=959328 bytes_retransmit=9 bytes_invalid=0 send_seq=3918 receive_seq=3918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24349 bytes_read=73224 bytes_retransmit=9 bytes_invalid=0 send_seq=3905 receive_seq=3905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78441 bytes_read=1569091 bytes_retransmit=0 bytes_invalid=0 send_seq=8464 receive_seq=8464 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998702 coil_temp=17.2 refs=0 mcu_temp=20.38 supply_voltage=3.012 th0: temp=47.8 th1: temp=47.2 th2: temp=50.7 th3: temp=48.7 sysload=0.38 cputime=297.814 memavail=7391964 print_time=3790.944 buffer_time=2.086 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.8 pwm=0.000
Testing frequency 120 Hz
Stats 3767.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21969234 bytes_read=2936684 bytes_retransmit=9 bytes_invalid=0 send_seq=391411 receive_seq=391411 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=23969 freq=400015868 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23602 bytes_read=74699 bytes_retransmit=0 bytes_invalid=0 send_seq=3905 receive_seq=3905 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997257 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140576 bytes_read=4329804 bytes_retransmit=9 bytes_invalid=0 send_seq=19020 receive_seq=19020 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997795 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=82893 bytes_read=1885414 bytes_retransmit=9 bytes_invalid=0 send_seq=10870 receive_seq=10870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23869 bytes_read=959637 bytes_retransmit=9 bytes_invalid=0 send_seq=3919 receive_seq=3919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24355 bytes_read=73251 bytes_retransmit=9 bytes_invalid=0 send_seq=3906 receive_seq=3906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78447 bytes_read=1569447 bytes_retransmit=0 bytes_invalid=0 send_seq=8465 receive_seq=8465 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998707 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.011 th0: temp=47.7 th1: temp=47.4 th2: temp=50.7 th3: temp=48.8 sysload=0.38 cputime=297.997 memavail=7391712 print_time=3792.139 buffer_time=2.282 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 121 Hz
Stats 3768.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21985627 bytes_read=2938399 bytes_retransmit=9 bytes_invalid=0 send_seq=391693 receive_seq=391693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=20348 freq=400015881 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23608 bytes_read=74715 bytes_retransmit=0 bytes_invalid=0 send_seq=3906 receive_seq=3906 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997246 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140652 bytes_read=4332863 bytes_retransmit=9 bytes_invalid=0 send_seq=19031 receive_seq=19031 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000241 adj=63997840 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=82969 bytes_read=1888546 bytes_retransmit=9 bytes_invalid=0 send_seq=10881 receive_seq=10881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997566 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23875 bytes_read=959871 bytes_retransmit=9 bytes_invalid=0 send_seq=3920 receive_seq=3920 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24361 bytes_read=73267 bytes_retransmit=9 bytes_invalid=0 send_seq=3907 receive_seq=3907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78453 bytes_read=1569803 bytes_retransmit=0 bytes_invalid=0 send_seq=8466 receive_seq=8466 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998688 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.011 th0: temp=47.7 th1: temp=47.2 th2: temp=50.6 th3: temp=48.6 sysload=0.35 cputime=298.164 memavail=7391736 print_time=3793.019 buffer_time=2.160 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 122 Hz
Stats 3769.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=21999494 bytes_read=2939924 bytes_retransmit=9 bytes_invalid=0 send_seq=391936 receive_seq=391936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=22740 freq=400016008 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23614 bytes_read=74744 bytes_retransmit=0 bytes_invalid=0 send_seq=3907 receive_seq=3907 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997228 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140728 bytes_read=4335978 bytes_retransmit=9 bytes_invalid=0 send_seq=19042 receive_seq=19042 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000242 adj=63997840 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=83045 bytes_read=1891603 bytes_retransmit=9 bytes_invalid=0 send_seq=10892 receive_seq=10892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997540 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23881 bytes_read=960105 bytes_retransmit=9 bytes_invalid=0 send_seq=3921 receive_seq=3921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997618 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24367 bytes_read=73283 bytes_retransmit=9 bytes_invalid=0 send_seq=3908 receive_seq=3908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78459 bytes_read=1570159 bytes_retransmit=0 bytes_invalid=0 send_seq=8467 receive_seq=8467 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998670 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.011 th0: temp=48.3 th1: temp=47.5 th2: temp=50.7 th3: temp=48.7 sysload=0.35 cputime=298.323 memavail=7391736 print_time=3793.943 buffer_time=2.084 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Testing frequency 123 Hz
Stats 3770.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=22016390 bytes_read=2941729 bytes_retransmit=9 bytes_invalid=0 send_seq=392226 receive_seq=392226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=24736 freq=400015996 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23620 bytes_read=74760 bytes_retransmit=0 bytes_invalid=0 send_seq=3908 receive_seq=3908 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997026 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140804 bytes_read=4339063 bytes_retransmit=9 bytes_invalid=0 send_seq=19053 receive_seq=19053 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997565 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=83121 bytes_read=1894688 bytes_retransmit=9 bytes_invalid=0 send_seq=10903 receive_seq=10903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997262 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23887 bytes_read=960399 bytes_retransmit=9 bytes_invalid=0 send_seq=3922 receive_seq=3922 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997422 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24373 bytes_read=73299 bytes_retransmit=9 bytes_invalid=0 send_seq=3909 receive_seq=3909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999412 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78465 bytes_read=1570515 bytes_retransmit=0 bytes_invalid=0 send_seq=8468 receive_seq=8468 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998543 coil_temp=17.2 refs=0 mcu_temp=20.36 supply_voltage=3.011 th0: temp=47.7 th1: temp=47.3 th2: temp=50.8 th3: temp=48.8 sysload=0.35 cputime=298.523 memavail=7386204 print_time=3795.144 buffer_time=2.284 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 124 Hz
Stats 3771.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=22033360 bytes_read=2943474 bytes_retransmit=9 bytes_invalid=0 send_seq=392513 receive_seq=392513 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=20668 freq=400016215 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23626 bytes_read=74776 bytes_retransmit=0 bytes_invalid=0 send_seq=3909 receive_seq=3909 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997098 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140880 bytes_read=4342137 bytes_retransmit=9 bytes_invalid=0 send_seq=19064 receive_seq=19064 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997602 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=83197 bytes_read=1897748 bytes_retransmit=9 bytes_invalid=0 send_seq=10914 receive_seq=10914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997335 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23893 bytes_read=960633 bytes_retransmit=9 bytes_invalid=0 send_seq=3923 receive_seq=3923 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997493 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24379 bytes_read=73315 bytes_retransmit=9 bytes_invalid=0 send_seq=3910 receive_seq=3910 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=31.0 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78471 bytes_read=1570871 bytes_retransmit=0 bytes_invalid=0 send_seq=8469 receive_seq=8469 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998580 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.011 th0: temp=47.9 th1: temp=47.4 th2: temp=50.9 th3: temp=48.8 sysload=0.35 cputime=298.688 memavail=7391828 print_time=3796.018 buffer_time=2.158 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 125 Hz
Stats 3772.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=22047276 bytes_read=2944959 bytes_retransmit=9 bytes_invalid=0 send_seq=392748 receive_seq=392748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=23135 freq=400016191 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23632 bytes_read=74792 bytes_retransmit=0 bytes_invalid=0 send_seq=3910 receive_seq=3910 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49996799 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140956 bytes_read=4345193 bytes_retransmit=9 bytes_invalid=0 send_seq=19075 receive_seq=19075 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997142 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=83273 bytes_read=1900805 bytes_retransmit=9 bytes_invalid=0 send_seq=10925 receive_seq=10925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63996909 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23899 bytes_read=960882 bytes_retransmit=9 bytes_invalid=0 send_seq=3924 receive_seq=3924 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997181 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24385 bytes_read=73342 bytes_retransmit=9 bytes_invalid=0 send_seq=3911 receive_seq=3911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999355 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78477 bytes_read=1571227 bytes_retransmit=0 bytes_invalid=0 send_seq=8470 receive_seq=8470 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998365 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.011 th0: temp=47.9 th1: temp=47.3 th2: temp=50.9 th3: temp=48.9 sysload=0.35 cputime=298.847 memavail=7391828 print_time=3796.948 buffer_time=2.087 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 126 Hz
Stats 3773.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=22064493 bytes_read=2946763 bytes_retransmit=9 bytes_invalid=0 send_seq=393041 receive_seq=393041 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=24903 freq=400016176 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23638 bytes_read=74808 bytes_retransmit=0 bytes_invalid=0 send_seq=3911 receive_seq=3911 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49996888 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141032 bytes_read=4348278 bytes_retransmit=9 bytes_invalid=0 send_seq=19086 receive_seq=19086 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997273 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=83349 bytes_read=1903906 bytes_retransmit=9 bytes_invalid=0 send_seq=10936 receive_seq=10936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997022 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23905 bytes_read=961176 bytes_retransmit=9 bytes_invalid=0 send_seq=3925 receive_seq=3925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997271 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24391 bytes_read=73358 bytes_retransmit=9 bytes_invalid=0 send_seq=3912 receive_seq=3912 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999924 adj=11999389 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78483 bytes_read=1571583 bytes_retransmit=0 bytes_invalid=0 send_seq=8471 receive_seq=8471 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998428 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.011 th0: temp=47.9 th1: temp=47.3 th2: temp=50.9 th3: temp=48.9 sysload=0.32 cputime=299.033 memavail=7391828 print_time=3798.149 buffer_time=2.287 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 127 Hz
Stats 3774.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=22081468 bytes_read=2948493 bytes_retransmit=9 bytes_invalid=0 send_seq=393325 receive_seq=393325 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=36 upcoming_bytes=20861 freq=400016160 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23644 bytes_read=74837 bytes_retransmit=0 bytes_invalid=0 send_seq=3912 receive_seq=3912 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49996997 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141108 bytes_read=4351335 bytes_retransmit=9 bytes_invalid=0 send_seq=19097 receive_seq=19097 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997374 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=83425 bytes_read=1906966 bytes_retransmit=9 bytes_invalid=0 send_seq=10947 receive_seq=10947 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997166 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23911 bytes_read=961410 bytes_retransmit=9 bytes_invalid=0 send_seq=3926 receive_seq=3926 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997389 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24397 bytes_read=73374 bytes_retransmit=9 bytes_invalid=0 send_seq=3913 receive_seq=3913 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999923 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78489 bytes_read=1571939 bytes_retransmit=0 bytes_invalid=0 send_seq=8472 receive_seq=8472 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998513 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.011 th0: temp=47.7 th1: temp=47.4 th2: temp=51.0 th3: temp=48.8 sysload=0.32 cputime=299.200 memavail=7391828 print_time=3799.022 buffer_time=2.159 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 128 Hz
Stats 3775.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=22095429 bytes_read=2950044 bytes_retransmit=9 bytes_invalid=0 send_seq=393570 receive_seq=393570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=23348 freq=400016135 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23650 bytes_read=74853 bytes_retransmit=0 bytes_invalid=0 send_seq=3913 receive_seq=3913 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997030 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141184 bytes_read=4354392 bytes_retransmit=9 bytes_invalid=0 send_seq=19108 receive_seq=19108 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997396 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=83501 bytes_read=1910081 bytes_retransmit=9 bytes_invalid=0 send_seq=10958 receive_seq=10958 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997213 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23917 bytes_read=961644 bytes_retransmit=9 bytes_invalid=0 send_seq=3927 receive_seq=3927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997428 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24403 bytes_read=73390 bytes_retransmit=9 bytes_invalid=0 send_seq=3914 receive_seq=3914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999923 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78495 bytes_read=1572295 bytes_retransmit=0 bytes_invalid=0 send_seq=8473 receive_seq=8473 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998540 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.011 th0: temp=47.8 th1: temp=47.3 th2: temp=50.8 th3: temp=48.8 sysload=0.32 cputime=299.360 memavail=7391828 print_time=3799.950 buffer_time=2.087 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 129 Hz
Stats 3776.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=22112810 bytes_read=2951873 bytes_retransmit=9 bytes_invalid=0 send_seq=393868 receive_seq=393868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=25388 freq=400016122 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23656 bytes_read=74869 bytes_retransmit=0 bytes_invalid=0 send_seq=3914 receive_seq=3914 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997092 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141253 bytes_read=4357473 bytes_retransmit=9 bytes_invalid=0 send_seq=19118 receive_seq=19118 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997445 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=83570 bytes_read=1913142 bytes_retransmit=9 bytes_invalid=0 send_seq=10968 receive_seq=10968 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997299 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=23923 bytes_read=961938 bytes_retransmit=9 bytes_invalid=0 send_seq=3928 receive_seq=3928 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997486 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24409 bytes_read=73406 bytes_retransmit=9 bytes_invalid=0 send_seq=3915 receive_seq=3915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999923 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78501 bytes_read=1572651 bytes_retransmit=0 bytes_invalid=0 send_seq=8474 receive_seq=8474 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998604 coil_temp=17.2 refs=0 mcu_temp=20.38 supply_voltage=3.011 th0: temp=47.9 th1: temp=47.3 th2: temp=50.9 th3: temp=48.9 sysload=0.32 cputime=299.545 memavail=7390836 print_time=3801.153 buffer_time=2.289 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Testing frequency 130 Hz
Stats 3777.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=22130021 bytes_read=2953663 bytes_retransmit=9 bytes_invalid=0 send_seq=394164 receive_seq=394164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=21052 freq=400016106 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23662 bytes_read=74885 bytes_retransmit=0 bytes_invalid=0 send_seq=3915 receive_seq=3915 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997140 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141329 bytes_read=4360588 bytes_retransmit=9 bytes_invalid=0 send_seq=19129 receive_seq=19129 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997498 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=83646 bytes_read=1916201 bytes_retransmit=9 bytes_invalid=0 send_seq=10979 receive_seq=10979 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997371 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23929 bytes_read=962187 bytes_retransmit=9 bytes_invalid=0 send_seq=3929 receive_seq=3929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997534 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24415 bytes_read=73433 bytes_retransmit=9 bytes_invalid=0 send_seq=3916 receive_seq=3916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999923 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78507 bytes_read=1573007 bytes_retransmit=0 bytes_invalid=0 send_seq=8475 receive_seq=8475 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998641 coil_temp=17.2 refs=0 mcu_temp=20.39 supply_voltage=3.011 th0: temp=47.9 th1: temp=47.6 th2: temp=50.7 th3: temp=49.0 sysload=0.32 cputime=299.711 memavail=7390836 print_time=3802.025 buffer_time=2.161 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 131 Hz
Stats 3778.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=22144204 bytes_read=2955211 bytes_retransmit=9 bytes_invalid=0 send_seq=394412 receive_seq=394412 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=23598 freq=400016085 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23668 bytes_read=74901 bytes_retransmit=0 bytes_invalid=0 send_seq=3916 receive_seq=3916 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997170 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141405 bytes_read=4363644 bytes_retransmit=9 bytes_invalid=0 send_seq=19140 receive_seq=19140 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997527 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=83722 bytes_read=1919275 bytes_retransmit=9 bytes_invalid=0 send_seq=10990 receive_seq=10990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997411 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23935 bytes_read=962421 bytes_retransmit=9 bytes_invalid=0 send_seq=3930 receive_seq=3930 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997567 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24421 bytes_read=73449 bytes_retransmit=9 bytes_invalid=0 send_seq=3917 receive_seq=3917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78513 bytes_read=1573363 bytes_retransmit=0 bytes_invalid=0 send_seq=8476 receive_seq=8476 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998657 coil_temp=17.2 refs=0 mcu_temp=20.39 supply_voltage=3.011 th0: temp=47.7 th1: temp=47.3 th2: temp=51.1 th3: temp=48.9 sysload=0.37 cputime=299.871 memavail=7390836 print_time=3802.951 buffer_time=2.086 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 132 Hz
Stats 3779.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=22161484 bytes_read=2957016 bytes_retransmit=9 bytes_invalid=0 send_seq=394706 receive_seq=394706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=25962 freq=400016077 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23674 bytes_read=74917 bytes_retransmit=0 bytes_invalid=0 send_seq=3917 receive_seq=3917 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997207 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141481 bytes_read=4366731 bytes_retransmit=9 bytes_invalid=0 send_seq=19151 receive_seq=19151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997743 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=83798 bytes_read=1922360 bytes_retransmit=9 bytes_invalid=0 send_seq=11001 receive_seq=11001 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997459 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23941 bytes_read=962715 bytes_retransmit=9 bytes_invalid=0 send_seq=3931 receive_seq=3931 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997600 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24427 bytes_read=73465 bytes_retransmit=9 bytes_invalid=0 send_seq=3918 receive_seq=3918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78519 bytes_read=1573719 bytes_retransmit=0 bytes_invalid=0 send_seq=8477 receive_seq=8477 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998687 coil_temp=17.2 refs=0 mcu_temp=20.38 supply_voltage=3.011 th0: temp=48.0 th1: temp=47.0 th2: temp=50.9 th3: temp=48.8 sysload=0.37 cputime=300.060 memavail=7390836 print_time=3804.155 buffer_time=2.290 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Stats 3780.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=22179008 bytes_read=2958847 bytes_retransmit=9 bytes_invalid=0 send_seq=395007 receive_seq=395007 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=20401 freq=400016070 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=23680 bytes_read=74946 bytes_retransmit=0 bytes_invalid=0 send_seq=3918 receive_seq=3918 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997214 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141557 bytes_read=4369787 bytes_retransmit=9 bytes_invalid=0 send_seq=19162 receive_seq=19162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000264 adj=63997694 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=83874 bytes_read=1925417 bytes_retransmit=9 bytes_invalid=0 send_seq=11012 receive_seq=11012 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23947 bytes_read=962949 bytes_retransmit=9 bytes_invalid=0 send_seq=3932 receive_seq=3932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997613 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24433 bytes_read=73481 bytes_retransmit=9 bytes_invalid=0 send_seq=3919 receive_seq=3919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78525 bytes_read=1574075 bytes_retransmit=0 bytes_invalid=0 send_seq=8478 receive_seq=8478 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998682 coil_temp=17.2 refs=0 mcu_temp=20.38 supply_voltage=3.011 th0: temp=47.9 th1: temp=47.5 th2: temp=51.1 th3: temp=48.9 sysload=0.37 cputime=300.216 memavail=7390840 print_time=3804.803 buffer_time=1.937 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3781.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=22193529 bytes_read=2960422 bytes_retransmit=9 bytes_invalid=0 send_seq=395260 receive_seq=395260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=7324 freq=400016057 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=23686 bytes_read=74962 bytes_retransmit=0 bytes_invalid=0 send_seq=3919 receive_seq=3919 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997209 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141633 bytes_read=4372864 bytes_retransmit=9 bytes_invalid=0 send_seq=19173 receive_seq=19173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000259 adj=63998110 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=83950 bytes_read=1928474 bytes_retransmit=9 bytes_invalid=0 send_seq=11023 receive_seq=11023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997486 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23953 bytes_read=963183 bytes_retransmit=9 bytes_invalid=0 send_seq=3933 receive_seq=3933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997626 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24439 bytes_read=73497 bytes_retransmit=9 bytes_invalid=0 send_seq=3920 receive_seq=3920 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78531 bytes_read=1574431 bytes_retransmit=0 bytes_invalid=0 send_seq=8479 receive_seq=8479 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998689 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.011 th0: temp=48.1 th1: temp=47.4 th2: temp=51.2 th3: temp=48.8 sysload=0.37 cputime=300.321 memavail=7390840 print_time=3804.803 buffer_time=0.936 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Writing raw accelerometer data to /tmp/raw_data_y_toolboard_t1_t2.csv file
Stats 3782.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=22201817 bytes_read=2961511 bytes_retransmit=9 bytes_invalid=0 send_seq=395410 receive_seq=395410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016045 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=23692 bytes_read=74978 bytes_retransmit=0 bytes_invalid=0 send_seq=3920 receive_seq=3920 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997238 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141709 bytes_read=4376007 bytes_retransmit=9 bytes_invalid=0 send_seq=19184 receive_seq=19184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000254 adj=63998074 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=84026 bytes_read=1931618 bytes_retransmit=9 bytes_invalid=0 send_seq=11034 receive_seq=11034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997503 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23959 bytes_read=963492 bytes_retransmit=9 bytes_invalid=0 send_seq=3934 receive_seq=3934 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24445 bytes_read=73524 bytes_retransmit=9 bytes_invalid=0 send_seq=3921 receive_seq=3921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78537 bytes_read=1574787 bytes_retransmit=0 bytes_invalid=0 send_seq=8480 receive_seq=8480 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998699 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=47.9 th1: temp=47.4 th2: temp=51.0 th3: temp=49.0 sysload=0.37 cputime=300.428 memavail=7387584 print_time=3805.122 buffer_time=0.249 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
LIS2DW finished 'toolboard_t1' measurements
Writing raw accelerometer data to /tmp/raw_data_y_toolboard_t0_t2.csv file
LIS2DW finished 'toolboard_t0' measurements
Stats 3783.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=22202115 bytes_read=2961936 bytes_retransmit=9 bytes_invalid=0 send_seq=395433 receive_seq=395433 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016048 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=23698 bytes_read=74994 bytes_retransmit=0 bytes_invalid=0 send_seq=3921 receive_seq=3921 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997257 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141791 bytes_read=4377289 bytes_retransmit=9 bytes_invalid=0 send_seq=19194 receive_seq=19194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000252 adj=63998035 toolboard_t1: mcu_awake=0.307 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=84087 bytes_read=1931919 bytes_retransmit=9 bytes_invalid=0 send_seq=11041 receive_seq=11041 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23965 bytes_read=963726 bytes_retransmit=9 bytes_invalid=0 send_seq=3935 receive_seq=3935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24451 bytes_read=73540 bytes_retransmit=9 bytes_invalid=0 send_seq=3922 receive_seq=3922 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999923 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78543 bytes_read=1575143 bytes_retransmit=0 bytes_invalid=0 send_seq=8481 receive_seq=8481 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998713 coil_temp=17.2 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=48.3 th1: temp=47.6 th2: temp=51.4 th3: temp=49.0 sysload=0.34 cputime=300.595 memavail=7392536 print_time=3810.480 buffer_time=4.606 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 3784.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=22202413 bytes_read=2962361 bytes_retransmit=9 bytes_invalid=0 send_seq=395456 receive_seq=395456 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016030 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=23704 bytes_read=75010 bytes_retransmit=0 bytes_invalid=0 send_seq=3922 receive_seq=3922 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997216 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141797 bytes_read=4377389 bytes_retransmit=9 bytes_invalid=0 send_seq=19195 receive_seq=19195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000249 adj=63997649 toolboard_t1: mcu_awake=0.307 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=84093 bytes_read=1932019 bytes_retransmit=9 bytes_invalid=0 send_seq=11042 receive_seq=11042 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997472 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23971 bytes_read=963960 bytes_retransmit=9 bytes_invalid=0 send_seq=3936 receive_seq=3936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997632 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24457 bytes_read=73556 bytes_retransmit=9 bytes_invalid=0 send_seq=3923 receive_seq=3923 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78549 bytes_read=1575499 bytes_retransmit=0 bytes_invalid=0 send_seq=8482 receive_seq=8482 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998651 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=48.2 th1: temp=47.5 th2: temp=51.1 th3: temp=49.0 sysload=0.34 cputime=300.638 memavail=7392536 print_time=3810.480 buffer_time=3.606 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 3785.3: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=22202711 bytes_read=2962831 bytes_retransmit=9 bytes_invalid=0 send_seq=395479 receive_seq=395479 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016037 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23710 bytes_read=75039 bytes_retransmit=0 bytes_invalid=0 send_seq=3923 receive_seq=3923 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997227 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141803 bytes_read=4377517 bytes_retransmit=9 bytes_invalid=0 send_seq=19196 receive_seq=19196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000245 adj=63997650 toolboard_t1: mcu_awake=0.307 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=84099 bytes_read=1932147 bytes_retransmit=9 bytes_invalid=0 send_seq=11043 receive_seq=11043 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23977 bytes_read=964254 bytes_retransmit=9 bytes_invalid=0 send_seq=3937 receive_seq=3937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24463 bytes_read=73572 bytes_retransmit=9 bytes_invalid=0 send_seq=3924 receive_seq=3924 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78555 bytes_read=1575855 bytes_retransmit=0 bytes_invalid=0 send_seq=8483 receive_seq=8483 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998660 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=48.1 th1: temp=47.6 th2: temp=51.1 th3: temp=48.8 sysload=0.34 cputime=300.682 memavail=7392288 print_time=3810.480 buffer_time=2.606 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Running Command {generate_tension_graphs}...:
Stats 3786.3: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=22203009 bytes_read=2963256 bytes_retransmit=9 bytes_invalid=0 send_seq=395502 receive_seq=395502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016022 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23716 bytes_read=75055 bytes_retransmit=0 bytes_invalid=0 send_seq=3924 receive_seq=3924 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997214 toolboard_t0: mcu_awake=0.144 mcu_task_avg=0.000110 mcu_task_stddev=0.000072 bytes_write=141809 bytes_read=4377634 bytes_retransmit=9 bytes_invalid=0 send_seq=19197 receive_seq=19197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000241 adj=63997617 toolboard_t1: mcu_awake=0.307 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=84105 bytes_read=1932247 bytes_retransmit=9 bytes_invalid=0 send_seq=11044 receive_seq=11044 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997481 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=23983 bytes_read=964488 bytes_retransmit=9 bytes_invalid=0 send_seq=3938 receive_seq=3938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997632 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24469 bytes_read=73588 bytes_retransmit=9 bytes_invalid=0 send_seq=3925 receive_seq=3925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78561 bytes_read=1576211 bytes_retransmit=0 bytes_invalid=0 send_seq=8484 receive_seq=8484 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998658 coil_temp=17.2 refs=0 mcu_temp=20.32 supply_voltage=3.012 th0: temp=47.6 th1: temp=47.5 th2: temp=51.0 th3: temp=48.9 sysload=0.34 cputime=300.744 memavail=7380168 print_time=3810.480 buffer_time=1.605 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3787.3: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=22203307 bytes_read=2963681 bytes_retransmit=9 bytes_invalid=0 send_seq=395525 receive_seq=395525 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016019 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23722 bytes_read=75071 bytes_retransmit=0 bytes_invalid=0 send_seq=3925 receive_seq=3925 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997219 toolboard_t0: mcu_awake=0.144 mcu_task_avg=0.000110 mcu_task_stddev=0.000072 bytes_write=141815 bytes_read=4377734 bytes_retransmit=9 bytes_invalid=0 send_seq=19198 receive_seq=19198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000247 adj=63997607 toolboard_t1: mcu_awake=0.307 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=84111 bytes_read=1932347 bytes_retransmit=9 bytes_invalid=0 send_seq=11045 receive_seq=11045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997497 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23989 bytes_read=964737 bytes_retransmit=9 bytes_invalid=0 send_seq=3939 receive_seq=3939 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24475 bytes_read=73615 bytes_retransmit=9 bytes_invalid=0 send_seq=3926 receive_seq=3926 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78567 bytes_read=1576567 bytes_retransmit=0 bytes_invalid=0 send_seq=8485 receive_seq=8485 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998661 coil_temp=17.2 refs=0 mcu_temp=20.32 supply_voltage=3.012 th0: temp=47.9 th1: temp=47.5 th2: temp=51.0 th3: temp=49.0 sysload=0.34 cputime=300.799 memavail=7368604 print_time=3810.480 buffer_time=0.605 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3788.3: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=22203605 bytes_read=2964135 bytes_retransmit=9 bytes_invalid=0 send_seq=395548 receive_seq=395548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016001 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23728 bytes_read=75086 bytes_retransmit=0 bytes_invalid=0 send_seq=3926 receive_seq=3926 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997223 toolboard_t0: mcu_awake=0.144 mcu_task_avg=0.000110 mcu_task_stddev=0.000072 bytes_write=141821 bytes_read=4377862 bytes_retransmit=9 bytes_invalid=0 send_seq=19199 receive_seq=19199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000244 adj=63997646 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=84117 bytes_read=1932489 bytes_retransmit=9 bytes_invalid=0 send_seq=11046 receive_seq=11046 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=23995 bytes_read=965031 bytes_retransmit=9 bytes_invalid=0 send_seq=3940 receive_seq=3940 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24481 bytes_read=73631 bytes_retransmit=9 bytes_invalid=0 send_seq=3927 receive_seq=3927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=30.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78573 bytes_read=1576923 bytes_retransmit=0 bytes_invalid=0 send_seq=8486 receive_seq=8486 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998701 coil_temp=17.2 refs=0 mcu_temp=20.32 supply_voltage=3.012 th0: temp=47.8 th1: temp=47.9 th2: temp=51.1 th3: temp=49.0 sysload=0.40 cputime=300.854 memavail=7374500 print_time=3810.480 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3789.3: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=22203909 bytes_read=2964571 bytes_retransmit=9 bytes_invalid=0 send_seq=395572 receive_seq=395572 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015987 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23740 bytes_read=75116 bytes_retransmit=0 bytes_invalid=0 send_seq=3928 receive_seq=3928 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997244 toolboard_t0: mcu_awake=0.144 mcu_task_avg=0.000110 mcu_task_stddev=0.000072 bytes_write=141833 bytes_read=4377978 bytes_retransmit=9 bytes_invalid=0 send_seq=19201 receive_seq=19201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997649 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=84129 bytes_read=1932605 bytes_retransmit=9 bytes_invalid=0 send_seq=11048 receive_seq=11048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=24007 bytes_read=965281 bytes_retransmit=9 bytes_invalid=0 send_seq=3942 receive_seq=3942 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997683 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24493 bytes_read=73663 bytes_retransmit=9 bytes_invalid=0 send_seq=3929 receive_seq=3929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78585 bytes_read=1577295 bytes_retransmit=0 bytes_invalid=0 send_seq=8488 receive_seq=8488 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999947 adj=31998702 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=47.7 th1: temp=47.7 th2: temp=51.1 th3: temp=49.0 sysload=0.40 cputime=300.913 memavail=7368108 print_time=3810.480 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3790.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22204207 bytes_read=2965011 bytes_retransmit=9 bytes_invalid=0 send_seq=395595 receive_seq=395595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015989 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23746 bytes_read=75144 bytes_retransmit=0 bytes_invalid=0 send_seq=3929 receive_seq=3929 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997272 toolboard_t0: mcu_awake=0.144 mcu_task_avg=0.000110 mcu_task_stddev=0.000072 bytes_write=141839 bytes_read=4378078 bytes_retransmit=9 bytes_invalid=0 send_seq=19202 receive_seq=19202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997622 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=84135 bytes_read=1932705 bytes_retransmit=9 bytes_invalid=0 send_seq=11049 receive_seq=11049 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=24013 bytes_read=965515 bytes_retransmit=9 bytes_invalid=0 send_seq=3943 receive_seq=3943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997718 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24499 bytes_read=73679 bytes_retransmit=9 bytes_invalid=0 send_seq=3930 receive_seq=3930 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78591 bytes_read=1577651 bytes_retransmit=0 bytes_invalid=0 send_seq=8489 receive_seq=8489 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998759 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=47.8 th1: temp=47.7 th2: temp=51.1 th3: temp=49.1 sysload=0.40 cputime=300.971 memavail=7367660 print_time=3810.480 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Command {generate_tension_graphs} finished

Running Command {generate_tension_graphs}...:
Stats 3791.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22204495 bytes_read=2965455 bytes_retransmit=9 bytes_invalid=0 send_seq=395616 receive_seq=395616 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015972 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23752 bytes_read=75159 bytes_retransmit=0 bytes_invalid=0 send_seq=3930 receive_seq=3930 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999214 adj=49997271 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=141845 bytes_read=4378220 bytes_retransmit=9 bytes_invalid=0 send_seq=19203 receive_seq=19203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997598 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=84141 bytes_read=1932833 bytes_retransmit=9 bytes_invalid=0 send_seq=11050 receive_seq=11050 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997540 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=24019 bytes_read=965809 bytes_retransmit=9 bytes_invalid=0 send_seq=3944 receive_seq=3944 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997713 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24505 bytes_read=73695 bytes_retransmit=9 bytes_invalid=0 send_seq=3931 receive_seq=3931 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=31.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78597 bytes_read=1578007 bytes_retransmit=0 bytes_invalid=0 send_seq=8490 receive_seq=8490 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998751 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=47.4 th1: temp=47.8 th2: temp=51.0 th3: temp=49.1 sysload=0.40 cputime=301.091 memavail=7378940 print_time=3810.480 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 3792.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22204793 bytes_read=2965880 bytes_retransmit=9 bytes_invalid=0 send_seq=395639 receive_seq=395639 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015961 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23758 bytes_read=75174 bytes_retransmit=0 bytes_invalid=0 send_seq=3931 receive_seq=3931 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999214 adj=49997293 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=141851 bytes_read=4378320 bytes_retransmit=9 bytes_invalid=0 send_seq=19204 receive_seq=19204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997601 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=84147 bytes_read=1932933 bytes_retransmit=9 bytes_invalid=0 send_seq=11051 receive_seq=11051 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997564 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24025 bytes_read=966058 bytes_retransmit=9 bytes_invalid=0 send_seq=3945 receive_seq=3945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997725 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24511 bytes_read=73722 bytes_retransmit=9 bytes_invalid=0 send_seq=3932 receive_seq=3932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78603 bytes_read=1578363 bytes_retransmit=0 bytes_invalid=0 send_seq=8491 receive_seq=8491 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998755 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=47.7 th1: temp=48.0 th2: temp=51.1 th3: temp=49.0 sysload=0.40 cputime=301.145 memavail=7376564 print_time=3810.480 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3793.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22205091 bytes_read=2966305 bytes_retransmit=9 bytes_invalid=0 send_seq=395662 receive_seq=395662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015950 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23764 bytes_read=75190 bytes_retransmit=0 bytes_invalid=0 send_seq=3932 receive_seq=3932 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999215 adj=49997311 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=141857 bytes_read=4378420 bytes_retransmit=9 bytes_invalid=0 send_seq=19205 receive_seq=19205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997606 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84153 bytes_read=1933047 bytes_retransmit=9 bytes_invalid=0 send_seq=11052 receive_seq=11052 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24031 bytes_read=966292 bytes_retransmit=9 bytes_invalid=0 send_seq=3946 receive_seq=3946 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997734 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24517 bytes_read=73738 bytes_retransmit=9 bytes_invalid=0 send_seq=3933 receive_seq=3933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78609 bytes_read=1578719 bytes_retransmit=0 bytes_invalid=0 send_seq=8492 receive_seq=8492 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998754 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=47.3 th1: temp=48.1 th2: temp=51.1 th3: temp=49.1 sysload=0.44 cputime=301.199 memavail=7374860 print_time=3810.480 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3794.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22205389 bytes_read=2966759 bytes_retransmit=9 bytes_invalid=0 send_seq=395685 receive_seq=395685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015941 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23770 bytes_read=75206 bytes_retransmit=0 bytes_invalid=0 send_seq=3933 receive_seq=3933 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999215 adj=49997330 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=141863 bytes_read=4378548 bytes_retransmit=9 bytes_invalid=0 send_seq=19206 receive_seq=19206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997592 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84159 bytes_read=1933175 bytes_retransmit=9 bytes_invalid=0 send_seq=11053 receive_seq=11053 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997610 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24037 bytes_read=966586 bytes_retransmit=9 bytes_invalid=0 send_seq=3947 receive_seq=3947 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997750 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24523 bytes_read=73754 bytes_retransmit=9 bytes_invalid=0 send_seq=3934 receive_seq=3934 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78615 bytes_read=1579075 bytes_retransmit=0 bytes_invalid=0 send_seq=8493 receive_seq=8493 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998750 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=47.3 th1: temp=47.9 th2: temp=51.1 th3: temp=49.1 sysload=0.44 cputime=301.270 memavail=7366340 print_time=3810.480 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Command {generate_tension_graphs} finished

toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Activating extruder extruder
Extruder 'extruder' now syncing with 'extruder'
Extruder 'extruder1' now syncing with 'extruder1'
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 3795.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22205780 bytes_read=2967209 bytes_retransmit=9 bytes_invalid=0 send_seq=395710 receive_seq=395710 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015924 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=23776 bytes_read=75235 bytes_retransmit=0 bytes_invalid=0 send_seq=3934 receive_seq=3934 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997352 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=141869 bytes_read=4378648 bytes_retransmit=9 bytes_invalid=0 send_seq=19207 receive_seq=19207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997577 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84165 bytes_read=1933275 bytes_retransmit=9 bytes_invalid=0 send_seq=11054 receive_seq=11054 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997654 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24043 bytes_read=966820 bytes_retransmit=9 bytes_invalid=0 send_seq=3948 receive_seq=3948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997804 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24529 bytes_read=73770 bytes_retransmit=9 bytes_invalid=0 send_seq=3935 receive_seq=3935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=31.6  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78621 bytes_read=1579431 bytes_retransmit=0 bytes_invalid=0 send_seq=8494 receive_seq=8494 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998762 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=47.1 th1: temp=48.1 th2: temp=51.3 th3: temp=49.0 sysload=0.44 cputime=301.425 memavail=7393808 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3796.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22206078 bytes_read=2967634 bytes_retransmit=9 bytes_invalid=0 send_seq=395733 receive_seq=395733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015909 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=23782 bytes_read=75251 bytes_retransmit=0 bytes_invalid=0 send_seq=3935 receive_seq=3935 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997402 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=141875 bytes_read=4378762 bytes_retransmit=9 bytes_invalid=0 send_seq=19208 receive_seq=19208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997596 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84171 bytes_read=1933375 bytes_retransmit=9 bytes_invalid=0 send_seq=11055 receive_seq=11055 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997688 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24049 bytes_read=967054 bytes_retransmit=9 bytes_invalid=0 send_seq=3949 receive_seq=3949 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997839 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24535 bytes_read=73786 bytes_retransmit=9 bytes_invalid=0 send_seq=3936 receive_seq=3936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=30.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78627 bytes_read=1579787 bytes_retransmit=0 bytes_invalid=0 send_seq=8495 receive_seq=8495 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998799 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=47.3 th1: temp=47.9 th2: temp=51.2 th3: temp=49.1 sysload=0.44 cputime=301.468 memavail=7393592 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3797.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22206371 bytes_read=2968083 bytes_retransmit=9 bytes_invalid=0 send_seq=395755 receive_seq=395755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015892 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=23788 bytes_read=75267 bytes_retransmit=0 bytes_invalid=0 send_seq=3936 receive_seq=3936 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997385 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=141881 bytes_read=4378890 bytes_retransmit=9 bytes_invalid=0 send_seq=19209 receive_seq=19209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997634 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84177 bytes_read=1933503 bytes_retransmit=9 bytes_invalid=0 send_seq=11056 receive_seq=11056 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997677 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=24055 bytes_read=967363 bytes_retransmit=9 bytes_invalid=0 send_seq=3950 receive_seq=3950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997807 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24541 bytes_read=73813 bytes_retransmit=9 bytes_invalid=0 send_seq=3937 receive_seq=3937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999468 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78633 bytes_read=1580143 bytes_retransmit=0 bytes_invalid=0 send_seq=8496 receive_seq=8496 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998781 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=47.4 th1: temp=47.6 th2: temp=51.1 th3: temp=48.9 sysload=0.44 cputime=301.513 memavail=7393372 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3798.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22206664 bytes_read=2968503 bytes_retransmit=9 bytes_invalid=0 send_seq=395777 receive_seq=395777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015884 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=23794 bytes_read=75283 bytes_retransmit=0 bytes_invalid=0 send_seq=3937 receive_seq=3937 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999214 adj=49997376 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=141887 bytes_read=4378990 bytes_retransmit=9 bytes_invalid=0 send_seq=19210 receive_seq=19210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997655 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84183 bytes_read=1933617 bytes_retransmit=9 bytes_invalid=0 send_seq=11057 receive_seq=11057 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997670 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=24061 bytes_read=967597 bytes_retransmit=9 bytes_invalid=0 send_seq=3951 receive_seq=3951 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997782 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24547 bytes_read=73829 bytes_retransmit=9 bytes_invalid=0 send_seq=3938 receive_seq=3938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78639 bytes_read=1580499 bytes_retransmit=0 bytes_invalid=0 send_seq=8497 receive_seq=8497 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998760 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=47.1 th1: temp=47.6 th2: temp=51.2 th3: temp=49.0 sysload=0.41 cputime=301.555 memavail=7393372 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3799.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22206962 bytes_read=2968928 bytes_retransmit=9 bytes_invalid=0 send_seq=395800 receive_seq=395800 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015870 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=23800 bytes_read=75299 bytes_retransmit=0 bytes_invalid=0 send_seq=3938 receive_seq=3938 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997334 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=141893 bytes_read=4379090 bytes_retransmit=9 bytes_invalid=0 send_seq=19211 receive_seq=19211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997741 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84189 bytes_read=1933717 bytes_retransmit=9 bytes_invalid=0 send_seq=11058 receive_seq=11058 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997643 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=24067 bytes_read=967831 bytes_retransmit=9 bytes_invalid=0 send_seq=3952 receive_seq=3952 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997760 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24553 bytes_read=73845 bytes_retransmit=9 bytes_invalid=0 send_seq=3939 receive_seq=3939 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78645 bytes_read=1580855 bytes_retransmit=0 bytes_invalid=0 send_seq=8498 receive_seq=8498 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998732 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=47.0 th1: temp=47.4 th2: temp=50.8 th3: temp=49.2 sysload=0.41 cputime=301.598 memavail=7393372 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3800.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22207260 bytes_read=2969392 bytes_retransmit=9 bytes_invalid=0 send_seq=395823 receive_seq=395823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015859 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23806 bytes_read=75328 bytes_retransmit=0 bytes_invalid=0 send_seq=3939 receive_seq=3939 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997310 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=141899 bytes_read=4379218 bytes_retransmit=9 bytes_invalid=0 send_seq=19212 receive_seq=19212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997720 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84195 bytes_read=1933845 bytes_retransmit=9 bytes_invalid=0 send_seq=11059 receive_seq=11059 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997634 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=24073 bytes_read=968125 bytes_retransmit=9 bytes_invalid=0 send_seq=3953 receive_seq=3953 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997778 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24559 bytes_read=73861 bytes_retransmit=9 bytes_invalid=0 send_seq=3940 receive_seq=3940 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78651 bytes_read=1581211 bytes_retransmit=0 bytes_invalid=0 send_seq=8499 receive_seq=8499 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998717 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=47.3 th1: temp=47.3 th2: temp=51.3 th3: temp=49.0 sysload=0.41 cputime=301.642 memavail=7393628 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3801.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22207553 bytes_read=2969812 bytes_retransmit=9 bytes_invalid=0 send_seq=395845 receive_seq=395845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015853 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23812 bytes_read=75344 bytes_retransmit=0 bytes_invalid=0 send_seq=3940 receive_seq=3940 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997304 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=141905 bytes_read=4379330 bytes_retransmit=9 bytes_invalid=0 send_seq=19213 receive_seq=19213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997702 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84201 bytes_read=1933943 bytes_retransmit=9 bytes_invalid=0 send_seq=11060 receive_seq=11060 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997623 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=24079 bytes_read=968359 bytes_retransmit=9 bytes_invalid=0 send_seq=3954 receive_seq=3954 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997798 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24565 bytes_read=73877 bytes_retransmit=9 bytes_invalid=0 send_seq=3941 receive_seq=3941 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78657 bytes_read=1581567 bytes_retransmit=0 bytes_invalid=0 send_seq=8500 receive_seq=8500 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998701 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=47.3 th1: temp=46.8 th2: temp=51.4 th3: temp=48.9 sysload=0.41 cputime=301.686 memavail=7393628 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 3802.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22207846 bytes_read=2970232 bytes_retransmit=9 bytes_invalid=0 send_seq=395867 receive_seq=395867 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015866 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23818 bytes_read=75360 bytes_retransmit=0 bytes_invalid=0 send_seq=3941 receive_seq=3941 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997289 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=141911 bytes_read=4379423 bytes_retransmit=9 bytes_invalid=0 send_seq=19214 receive_seq=19214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997672 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84207 bytes_read=1934036 bytes_retransmit=9 bytes_invalid=0 send_seq=11061 receive_seq=11061 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997608 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24085 bytes_read=968608 bytes_retransmit=9 bytes_invalid=0 send_seq=3955 receive_seq=3955 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997798 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24571 bytes_read=73904 bytes_retransmit=9 bytes_invalid=0 send_seq=3942 receive_seq=3942 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78663 bytes_read=1581923 bytes_retransmit=0 bytes_invalid=0 send_seq=8501 receive_seq=8501 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998684 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=47.1 th1: temp=47.0 th2: temp=51.3 th3: temp=49.0 sysload=0.41 cputime=301.732 memavail=7393636 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3803.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22208144 bytes_read=2970686 bytes_retransmit=9 bytes_invalid=0 send_seq=395890 receive_seq=395890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015854 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23824 bytes_read=75376 bytes_retransmit=0 bytes_invalid=0 send_seq=3942 receive_seq=3942 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997253 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=141917 bytes_read=4379542 bytes_retransmit=9 bytes_invalid=0 send_seq=19215 receive_seq=19215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997611 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=84213 bytes_read=1934169 bytes_retransmit=9 bytes_invalid=0 send_seq=11062 receive_seq=11062 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24091 bytes_read=968902 bytes_retransmit=9 bytes_invalid=0 send_seq=3956 receive_seq=3956 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997717 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24577 bytes_read=73920 bytes_retransmit=9 bytes_invalid=0 send_seq=3943 receive_seq=3943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78669 bytes_read=1582279 bytes_retransmit=0 bytes_invalid=0 send_seq=8502 receive_seq=8502 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998650 coil_temp=17.2 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=46.8 th1: temp=47.0 th2: temp=51.4 th3: temp=49.2 sysload=0.38 cputime=301.777 memavail=7393632 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3804.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22208437 bytes_read=2971106 bytes_retransmit=9 bytes_invalid=0 send_seq=395912 receive_seq=395912 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015841 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23830 bytes_read=75392 bytes_retransmit=0 bytes_invalid=0 send_seq=3943 receive_seq=3943 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997268 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=141923 bytes_read=4379635 bytes_retransmit=9 bytes_invalid=0 send_seq=19216 receive_seq=19216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997628 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=84219 bytes_read=1934262 bytes_retransmit=9 bytes_invalid=0 send_seq=11063 receive_seq=11063 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997690 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24097 bytes_read=969136 bytes_retransmit=9 bytes_invalid=0 send_seq=3957 receive_seq=3957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997706 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24583 bytes_read=73936 bytes_retransmit=9 bytes_invalid=0 send_seq=3944 receive_seq=3944 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78675 bytes_read=1582635 bytes_retransmit=0 bytes_invalid=0 send_seq=8503 receive_seq=8503 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998654 coil_temp=17.2 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.9 th2: temp=51.6 th3: temp=49.0 sysload=0.38 cputime=301.820 memavail=7393632 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3805.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22208735 bytes_read=2971546 bytes_retransmit=9 bytes_invalid=0 send_seq=395935 receive_seq=395935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015830 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23836 bytes_read=75421 bytes_retransmit=0 bytes_invalid=0 send_seq=3944 receive_seq=3944 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997280 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=141929 bytes_read=4379728 bytes_retransmit=9 bytes_invalid=0 send_seq=19217 receive_seq=19217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997670 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=84225 bytes_read=1934355 bytes_retransmit=9 bytes_invalid=0 send_seq=11064 receive_seq=11064 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997668 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24103 bytes_read=969370 bytes_retransmit=9 bytes_invalid=0 send_seq=3958 receive_seq=3958 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997702 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24589 bytes_read=73952 bytes_retransmit=9 bytes_invalid=0 send_seq=3945 receive_seq=3945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78681 bytes_read=1582991 bytes_retransmit=0 bytes_invalid=0 send_seq=8504 receive_seq=8504 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998666 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.9 th2: temp=51.4 th3: temp=49.1 sysload=0.38 cputime=301.867 memavail=7393004 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 3806.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22209028 bytes_read=2971995 bytes_retransmit=9 bytes_invalid=0 send_seq=395957 receive_seq=395957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015823 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23842 bytes_read=75437 bytes_retransmit=0 bytes_invalid=0 send_seq=3945 receive_seq=3945 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997276 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=141935 bytes_read=4379870 bytes_retransmit=9 bytes_invalid=0 send_seq=19218 receive_seq=19218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997677 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=84231 bytes_read=1934483 bytes_retransmit=9 bytes_invalid=0 send_seq=11065 receive_seq=11065 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997643 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24109 bytes_read=969664 bytes_retransmit=9 bytes_invalid=0 send_seq=3959 receive_seq=3959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997694 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24595 bytes_read=73968 bytes_retransmit=9 bytes_invalid=0 send_seq=3946 receive_seq=3946 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78687 bytes_read=1583347 bytes_retransmit=0 bytes_invalid=0 send_seq=8505 receive_seq=8505 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998673 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=46.8 th1: temp=47.0 th2: temp=51.2 th3: temp=49.3 sysload=0.38 cputime=301.911 memavail=7395924 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3807.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22209326 bytes_read=2972420 bytes_retransmit=9 bytes_invalid=0 send_seq=395980 receive_seq=395980 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015836 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23848 bytes_read=75453 bytes_retransmit=0 bytes_invalid=0 send_seq=3946 receive_seq=3946 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997279 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=141941 bytes_read=4379970 bytes_retransmit=9 bytes_invalid=0 send_seq=19219 receive_seq=19219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997688 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=84237 bytes_read=1934583 bytes_retransmit=9 bytes_invalid=0 send_seq=11066 receive_seq=11066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997623 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24115 bytes_read=969913 bytes_retransmit=9 bytes_invalid=0 send_seq=3960 receive_seq=3960 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997696 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24601 bytes_read=73995 bytes_retransmit=9 bytes_invalid=0 send_seq=3947 receive_seq=3947 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78693 bytes_read=1583703 bytes_retransmit=0 bytes_invalid=0 send_seq=8506 receive_seq=8506 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998706 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.9 th2: temp=51.4 th3: temp=49.0 sysload=0.38 cputime=301.953 memavail=7395924 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3808.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22209624 bytes_read=2972845 bytes_retransmit=9 bytes_invalid=0 send_seq=396003 receive_seq=396003 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015825 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23854 bytes_read=75469 bytes_retransmit=0 bytes_invalid=0 send_seq=3947 receive_seq=3947 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997243 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=141947 bytes_read=4380070 bytes_retransmit=9 bytes_invalid=0 send_seq=19220 receive_seq=19220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997629 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=84243 bytes_read=1934697 bytes_retransmit=9 bytes_invalid=0 send_seq=11067 receive_seq=11067 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997555 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24121 bytes_read=970147 bytes_retransmit=9 bytes_invalid=0 send_seq=3961 receive_seq=3961 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997649 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24607 bytes_read=74011 bytes_retransmit=9 bytes_invalid=0 send_seq=3948 receive_seq=3948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78699 bytes_read=1584059 bytes_retransmit=0 bytes_invalid=0 send_seq=8507 receive_seq=8507 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998680 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.7 th2: temp=51.7 th3: temp=49.2 sysload=0.35 cputime=301.996 memavail=7395924 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3809.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22209922 bytes_read=2973299 bytes_retransmit=9 bytes_invalid=0 send_seq=396026 receive_seq=396026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015817 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23860 bytes_read=75485 bytes_retransmit=0 bytes_invalid=0 send_seq=3948 receive_seq=3948 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997265 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=141953 bytes_read=4380198 bytes_retransmit=9 bytes_invalid=0 send_seq=19221 receive_seq=19221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997645 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=84249 bytes_read=1934825 bytes_retransmit=9 bytes_invalid=0 send_seq=11068 receive_seq=11068 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997571 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24127 bytes_read=970441 bytes_retransmit=9 bytes_invalid=0 send_seq=3962 receive_seq=3962 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24613 bytes_read=74027 bytes_retransmit=9 bytes_invalid=0 send_seq=3949 receive_seq=3949 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78705 bytes_read=1584415 bytes_retransmit=0 bytes_invalid=0 send_seq=8508 receive_seq=8508 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998683 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=46.9 th1: temp=46.9 th2: temp=51.0 th3: temp=49.1 sysload=0.35 cputime=302.040 memavail=7395924 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Stats 3810.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22210220 bytes_read=2973739 bytes_retransmit=9 bytes_invalid=0 send_seq=396049 receive_seq=396049 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015808 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23866 bytes_read=75514 bytes_retransmit=0 bytes_invalid=0 send_seq=3949 receive_seq=3949 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997265 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=141959 bytes_read=4380298 bytes_retransmit=9 bytes_invalid=0 send_seq=19222 receive_seq=19222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997655 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=84255 bytes_read=1934925 bytes_retransmit=9 bytes_invalid=0 send_seq=11069 receive_seq=11069 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997569 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24133 bytes_read=970675 bytes_retransmit=9 bytes_invalid=0 send_seq=3963 receive_seq=3963 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24619 bytes_read=74043 bytes_retransmit=9 bytes_invalid=0 send_seq=3950 receive_seq=3950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78711 bytes_read=1584771 bytes_retransmit=0 bytes_invalid=0 send_seq=8509 receive_seq=8509 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998708 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=46.8 th1: temp=46.7 th2: temp=51.5 th3: temp=49.1 sysload=0.35 cputime=302.082 memavail=7395924 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3811.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22210518 bytes_read=2974159 bytes_retransmit=9 bytes_invalid=0 send_seq=396072 receive_seq=396072 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015802 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23872 bytes_read=75530 bytes_retransmit=0 bytes_invalid=0 send_seq=3950 receive_seq=3950 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997263 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=141965 bytes_read=4380412 bytes_retransmit=9 bytes_invalid=0 send_seq=19223 receive_seq=19223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997659 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=84261 bytes_read=1935025 bytes_retransmit=9 bytes_invalid=0 send_seq=11070 receive_seq=11070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997571 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24139 bytes_read=970909 bytes_retransmit=9 bytes_invalid=0 send_seq=3964 receive_seq=3964 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24625 bytes_read=74059 bytes_retransmit=9 bytes_invalid=0 send_seq=3951 receive_seq=3951 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78717 bytes_read=1585127 bytes_retransmit=0 bytes_invalid=0 send_seq=8510 receive_seq=8510 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998702 coil_temp=17.2 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=47.0 th1: temp=46.5 th2: temp=51.3 th3: temp=49.1 sysload=0.35 cputime=302.125 memavail=7395924 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3812.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22210816 bytes_read=2974613 bytes_retransmit=9 bytes_invalid=0 send_seq=396095 receive_seq=396095 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015800 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23878 bytes_read=75546 bytes_retransmit=0 bytes_invalid=0 send_seq=3951 receive_seq=3951 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997251 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=141971 bytes_read=4380540 bytes_retransmit=9 bytes_invalid=0 send_seq=19224 receive_seq=19224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997659 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=84267 bytes_read=1935153 bytes_retransmit=9 bytes_invalid=0 send_seq=11071 receive_seq=11071 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997562 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24145 bytes_read=971218 bytes_retransmit=9 bytes_invalid=0 send_seq=3965 receive_seq=3965 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24631 bytes_read=74086 bytes_retransmit=9 bytes_invalid=0 send_seq=3952 receive_seq=3952 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78723 bytes_read=1585483 bytes_retransmit=0 bytes_invalid=0 send_seq=8511 receive_seq=8511 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998693 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=46.8 th1: temp=46.5 th2: temp=51.3 th3: temp=49.0 sysload=0.35 cputime=302.169 memavail=7395928 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 3813.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22211114 bytes_read=2975038 bytes_retransmit=9 bytes_invalid=0 send_seq=396118 receive_seq=396118 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015829 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23884 bytes_read=75562 bytes_retransmit=0 bytes_invalid=0 send_seq=3952 receive_seq=3952 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999208 adj=49997249 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=141977 bytes_read=4380640 bytes_retransmit=9 bytes_invalid=0 send_seq=19225 receive_seq=19225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997666 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84273 bytes_read=1935267 bytes_retransmit=9 bytes_invalid=0 send_seq=11072 receive_seq=11072 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997550 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24151 bytes_read=971452 bytes_retransmit=9 bytes_invalid=0 send_seq=3966 receive_seq=3966 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24637 bytes_read=74102 bytes_retransmit=9 bytes_invalid=0 send_seq=3953 receive_seq=3953 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78729 bytes_read=1585839 bytes_retransmit=0 bytes_invalid=0 send_seq=8512 receive_seq=8512 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998685 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.4 th2: temp=51.4 th3: temp=49.2 sysload=0.32 cputime=302.212 memavail=7395704 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3814.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22211412 bytes_read=2975463 bytes_retransmit=9 bytes_invalid=0 send_seq=396141 receive_seq=396141 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015821 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23890 bytes_read=75578 bytes_retransmit=0 bytes_invalid=0 send_seq=3953 receive_seq=3953 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997187 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=141983 bytes_read=4380740 bytes_retransmit=9 bytes_invalid=0 send_seq=19226 receive_seq=19226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997579 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84279 bytes_read=1935367 bytes_retransmit=9 bytes_invalid=0 send_seq=11073 receive_seq=11073 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997462 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24157 bytes_read=971686 bytes_retransmit=9 bytes_invalid=0 send_seq=3967 receive_seq=3967 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997599 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24643 bytes_read=74118 bytes_retransmit=9 bytes_invalid=0 send_seq=3954 receive_seq=3954 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78735 bytes_read=1586195 bytes_retransmit=0 bytes_invalid=0 send_seq=8513 receive_seq=8513 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998635 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=46.9 th1: temp=46.3 th2: temp=51.3 th3: temp=49.1 sysload=0.32 cputime=302.256 memavail=7395704 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3815.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22211710 bytes_read=2975932 bytes_retransmit=9 bytes_invalid=0 send_seq=396164 receive_seq=396164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015820 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23896 bytes_read=75607 bytes_retransmit=0 bytes_invalid=0 send_seq=3954 receive_seq=3954 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997226 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=141989 bytes_read=4380868 bytes_retransmit=9 bytes_invalid=0 send_seq=19227 receive_seq=19227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997608 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84285 bytes_read=1935495 bytes_retransmit=9 bytes_invalid=0 send_seq=11074 receive_seq=11074 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24163 bytes_read=971980 bytes_retransmit=9 bytes_invalid=0 send_seq=3968 receive_seq=3968 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997614 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24649 bytes_read=74134 bytes_retransmit=9 bytes_invalid=0 send_seq=3955 receive_seq=3955 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78741 bytes_read=1586551 bytes_retransmit=0 bytes_invalid=0 send_seq=8514 receive_seq=8514 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998645 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=46.5 th1: temp=46.5 th2: temp=51.4 th3: temp=49.2 sysload=0.32 cputime=302.301 memavail=7395704 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3816.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22212008 bytes_read=2976357 bytes_retransmit=9 bytes_invalid=0 send_seq=396187 receive_seq=396187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015816 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23902 bytes_read=75623 bytes_retransmit=0 bytes_invalid=0 send_seq=3955 receive_seq=3955 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997228 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=141995 bytes_read=4380982 bytes_retransmit=9 bytes_invalid=0 send_seq=19228 receive_seq=19228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997627 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84291 bytes_read=1935595 bytes_retransmit=9 bytes_invalid=0 send_seq=11075 receive_seq=11075 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24169 bytes_read=972214 bytes_retransmit=9 bytes_invalid=0 send_seq=3969 receive_seq=3969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997615 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24655 bytes_read=74150 bytes_retransmit=9 bytes_invalid=0 send_seq=3956 receive_seq=3956 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78747 bytes_read=1586907 bytes_retransmit=0 bytes_invalid=0 send_seq=8515 receive_seq=8515 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998647 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.2 th2: temp=51.5 th3: temp=49.1 sysload=0.32 cputime=302.345 memavail=7394008 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3817.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22212306 bytes_read=2976782 bytes_retransmit=9 bytes_invalid=0 send_seq=396210 receive_seq=396210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015816 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23908 bytes_read=75639 bytes_retransmit=0 bytes_invalid=0 send_seq=3956 receive_seq=3956 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997248 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142001 bytes_read=4381082 bytes_retransmit=9 bytes_invalid=0 send_seq=19229 receive_seq=19229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997629 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84297 bytes_read=1935695 bytes_retransmit=9 bytes_invalid=0 send_seq=11076 receive_seq=11076 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997503 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24175 bytes_read=972463 bytes_retransmit=9 bytes_invalid=0 send_seq=3970 receive_seq=3970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997621 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24661 bytes_read=74177 bytes_retransmit=9 bytes_invalid=0 send_seq=3957 receive_seq=3957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78753 bytes_read=1587263 bytes_retransmit=0 bytes_invalid=0 send_seq=8516 receive_seq=8516 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998659 coil_temp=17.2 refs=0 mcu_temp=20.36 supply_voltage=3.012 th0: temp=46.8 th1: temp=46.4 th2: temp=51.5 th3: temp=49.1 sysload=0.32 cputime=302.390 memavail=7394008 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3818.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22212604 bytes_read=2977236 bytes_retransmit=9 bytes_invalid=0 send_seq=396233 receive_seq=396233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015815 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23914 bytes_read=75655 bytes_retransmit=0 bytes_invalid=0 send_seq=3957 receive_seq=3957 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997237 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142007 bytes_read=4381210 bytes_retransmit=9 bytes_invalid=0 send_seq=19230 receive_seq=19230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997627 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84303 bytes_read=1935837 bytes_retransmit=9 bytes_invalid=0 send_seq=11077 receive_seq=11077 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24181 bytes_read=972757 bytes_retransmit=9 bytes_invalid=0 send_seq=3971 receive_seq=3971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997617 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24667 bytes_read=74193 bytes_retransmit=9 bytes_invalid=0 send_seq=3958 receive_seq=3958 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.3  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78759 bytes_read=1587619 bytes_retransmit=0 bytes_invalid=0 send_seq=8517 receive_seq=8517 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998649 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.3 th2: temp=51.5 th3: temp=49.0 sysload=0.29 cputime=302.433 memavail=7394008 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3819.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22212902 bytes_read=2977661 bytes_retransmit=9 bytes_invalid=0 send_seq=396256 receive_seq=396256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015810 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23920 bytes_read=75671 bytes_retransmit=0 bytes_invalid=0 send_seq=3958 receive_seq=3958 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997225 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142013 bytes_read=4381310 bytes_retransmit=9 bytes_invalid=0 send_seq=19231 receive_seq=19231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997625 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84309 bytes_read=1935937 bytes_retransmit=9 bytes_invalid=0 send_seq=11078 receive_seq=11078 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24187 bytes_read=972991 bytes_retransmit=9 bytes_invalid=0 send_seq=3972 receive_seq=3972 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24673 bytes_read=74209 bytes_retransmit=9 bytes_invalid=0 send_seq=3959 receive_seq=3959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78765 bytes_read=1587975 bytes_retransmit=0 bytes_invalid=0 send_seq=8518 receive_seq=8518 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998652 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.2 th2: temp=51.4 th3: temp=49.2 sysload=0.29 cputime=302.475 memavail=7394008 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3820.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22213195 bytes_read=2978096 bytes_retransmit=9 bytes_invalid=0 send_seq=396278 receive_seq=396278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015810 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23926 bytes_read=75700 bytes_retransmit=0 bytes_invalid=0 send_seq=3959 receive_seq=3959 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997239 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142019 bytes_read=4381410 bytes_retransmit=9 bytes_invalid=0 send_seq=19232 receive_seq=19232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997635 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84315 bytes_read=1936037 bytes_retransmit=9 bytes_invalid=0 send_seq=11079 receive_seq=11079 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997525 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24193 bytes_read=973225 bytes_retransmit=9 bytes_invalid=0 send_seq=3973 receive_seq=3973 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24679 bytes_read=74225 bytes_retransmit=9 bytes_invalid=0 send_seq=3960 receive_seq=3960 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78771 bytes_read=1588331 bytes_retransmit=0 bytes_invalid=0 send_seq=8519 receive_seq=8519 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998658 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.012 th0: temp=46.8 th1: temp=46.0 th2: temp=51.2 th3: temp=49.2 sysload=0.29 cputime=302.518 memavail=7394032 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3821.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22213463 bytes_read=2978516 bytes_retransmit=9 bytes_invalid=0 send_seq=396295 receive_seq=396295 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015811 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23932 bytes_read=75716 bytes_retransmit=0 bytes_invalid=0 send_seq=3960 receive_seq=3960 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997281 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142025 bytes_read=4381552 bytes_retransmit=9 bytes_invalid=0 send_seq=19233 receive_seq=19233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997682 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84321 bytes_read=1936165 bytes_retransmit=9 bytes_invalid=0 send_seq=11080 receive_seq=11080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997540 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24199 bytes_read=973519 bytes_retransmit=9 bytes_invalid=0 send_seq=3974 receive_seq=3974 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24685 bytes_read=74241 bytes_retransmit=9 bytes_invalid=0 send_seq=3961 receive_seq=3961 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78777 bytes_read=1588687 bytes_retransmit=0 bytes_invalid=0 send_seq=8520 receive_seq=8520 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998656 coil_temp=17.2 refs=0 mcu_temp=20.36 supply_voltage=3.012 th0: temp=46.6 th1: temp=46.0 th2: temp=51.3 th3: temp=49.1 sysload=0.29 cputime=302.562 memavail=7394032 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3822.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22213761 bytes_read=2978938 bytes_retransmit=9 bytes_invalid=0 send_seq=396318 receive_seq=396318 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015813 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23938 bytes_read=75732 bytes_retransmit=0 bytes_invalid=0 send_seq=3961 receive_seq=3961 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997273 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142031 bytes_read=4381652 bytes_retransmit=9 bytes_invalid=0 send_seq=19234 receive_seq=19234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997814 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84327 bytes_read=1936265 bytes_retransmit=9 bytes_invalid=0 send_seq=11081 receive_seq=11081 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997529 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24205 bytes_read=973768 bytes_retransmit=9 bytes_invalid=0 send_seq=3975 receive_seq=3975 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24691 bytes_read=74268 bytes_retransmit=9 bytes_invalid=0 send_seq=3962 receive_seq=3962 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78783 bytes_read=1589027 bytes_retransmit=0 bytes_invalid=0 send_seq=8521 receive_seq=8521 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998646 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=46.6 th1: temp=46.1 th2: temp=51.4 th3: temp=49.2 sysload=0.29 cputime=302.609 memavail=7394036 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 3823.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22214059 bytes_read=2979363 bytes_retransmit=9 bytes_invalid=0 send_seq=396341 receive_seq=396341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015805 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23944 bytes_read=75748 bytes_retransmit=0 bytes_invalid=0 send_seq=3962 receive_seq=3962 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997271 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142037 bytes_read=4381752 bytes_retransmit=9 bytes_invalid=0 send_seq=19235 receive_seq=19235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997897 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84333 bytes_read=1936379 bytes_retransmit=9 bytes_invalid=0 send_seq=11082 receive_seq=11082 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24211 bytes_read=974002 bytes_retransmit=9 bytes_invalid=0 send_seq=3976 receive_seq=3976 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24697 bytes_read=74284 bytes_retransmit=9 bytes_invalid=0 send_seq=3963 receive_seq=3963 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78789 bytes_read=1589383 bytes_retransmit=0 bytes_invalid=0 send_seq=8522 receive_seq=8522 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998645 coil_temp=17.2 refs=0 mcu_temp=20.36 supply_voltage=3.012 th0: temp=46.8 th1: temp=46.0 th2: temp=51.2 th3: temp=49.2 sysload=0.27 cputime=302.653 memavail=7395244 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3824.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22214357 bytes_read=2979817 bytes_retransmit=9 bytes_invalid=0 send_seq=396364 receive_seq=396364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015799 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=23950 bytes_read=75764 bytes_retransmit=0 bytes_invalid=0 send_seq=3963 receive_seq=3963 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997266 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142043 bytes_read=4381880 bytes_retransmit=9 bytes_invalid=0 send_seq=19236 receive_seq=19236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997835 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84339 bytes_read=1936507 bytes_retransmit=9 bytes_invalid=0 send_seq=11083 receive_seq=11083 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24217 bytes_read=974278 bytes_retransmit=9 bytes_invalid=0 send_seq=3977 receive_seq=3977 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24703 bytes_read=74300 bytes_retransmit=9 bytes_invalid=0 send_seq=3964 receive_seq=3964 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78795 bytes_read=1589739 bytes_retransmit=0 bytes_invalid=0 send_seq=8523 receive_seq=8523 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998658 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=46.4 th1: temp=46.1 th2: temp=51.7 th3: temp=49.2 sysload=0.27 cputime=302.697 memavail=7395244 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3825.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22214650 bytes_read=2980252 bytes_retransmit=9 bytes_invalid=0 send_seq=396386 receive_seq=396386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015800 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=23956 bytes_read=75793 bytes_retransmit=0 bytes_invalid=0 send_seq=3964 receive_seq=3964 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997263 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142049 bytes_read=4381980 bytes_retransmit=9 bytes_invalid=0 send_seq=19237 receive_seq=19237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997904 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84345 bytes_read=1936607 bytes_retransmit=9 bytes_invalid=0 send_seq=11084 receive_seq=11084 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997541 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24223 bytes_read=974496 bytes_retransmit=9 bytes_invalid=0 send_seq=3978 receive_seq=3978 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24709 bytes_read=74316 bytes_retransmit=9 bytes_invalid=0 send_seq=3965 receive_seq=3965 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78801 bytes_read=1590095 bytes_retransmit=0 bytes_invalid=0 send_seq=8524 receive_seq=8524 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998692 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=46.8 th1: temp=46.0 th2: temp=51.3 th3: temp=49.1 sysload=0.27 cputime=302.739 memavail=7395244 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3826.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22214948 bytes_read=2980677 bytes_retransmit=9 bytes_invalid=0 send_seq=396409 receive_seq=396409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015800 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=23962 bytes_read=75809 bytes_retransmit=0 bytes_invalid=0 send_seq=3965 receive_seq=3965 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997248 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=142055 bytes_read=4382094 bytes_retransmit=9 bytes_invalid=0 send_seq=19238 receive_seq=19238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997825 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84351 bytes_read=1936707 bytes_retransmit=9 bytes_invalid=0 send_seq=11085 receive_seq=11085 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24229 bytes_read=974714 bytes_retransmit=9 bytes_invalid=0 send_seq=3979 receive_seq=3979 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24715 bytes_read=74332 bytes_retransmit=9 bytes_invalid=0 send_seq=3966 receive_seq=3966 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999449 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78807 bytes_read=1590451 bytes_retransmit=0 bytes_invalid=0 send_seq=8525 receive_seq=8525 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998707 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=47.1 th1: temp=46.2 th2: temp=51.4 th3: temp=49.2 sysload=0.27 cputime=302.783 memavail=7395252 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3827.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22215246 bytes_read=2981131 bytes_retransmit=9 bytes_invalid=0 send_seq=396432 receive_seq=396432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015801 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=23968 bytes_read=75825 bytes_retransmit=0 bytes_invalid=0 send_seq=3966 receive_seq=3966 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997246 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=142061 bytes_read=4382222 bytes_retransmit=9 bytes_invalid=0 send_seq=19239 receive_seq=19239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997758 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84357 bytes_read=1936835 bytes_retransmit=9 bytes_invalid=0 send_seq=11086 receive_seq=11086 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=24235 bytes_read=975003 bytes_retransmit=9 bytes_invalid=0 send_seq=3980 receive_seq=3980 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24721 bytes_read=74359 bytes_retransmit=9 bytes_invalid=0 send_seq=3967 receive_seq=3967 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78813 bytes_read=1590807 bytes_retransmit=0 bytes_invalid=0 send_seq=8526 receive_seq=8526 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998693 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.8 th2: temp=51.5 th3: temp=49.2 sysload=0.27 cputime=302.828 memavail=7395252 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3828.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22215544 bytes_read=2981556 bytes_retransmit=9 bytes_invalid=0 send_seq=396455 receive_seq=396455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015801 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=23974 bytes_read=75841 bytes_retransmit=0 bytes_invalid=0 send_seq=3967 receive_seq=3967 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997252 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=142067 bytes_read=4382322 bytes_retransmit=9 bytes_invalid=0 send_seq=19240 receive_seq=19240 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997783 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84363 bytes_read=1936935 bytes_retransmit=9 bytes_invalid=0 send_seq=11087 receive_seq=11087 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997525 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=24241 bytes_read=975221 bytes_retransmit=9 bytes_invalid=0 send_seq=3981 receive_seq=3981 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24727 bytes_read=74375 bytes_retransmit=9 bytes_invalid=0 send_seq=3968 receive_seq=3968 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78819 bytes_read=1591163 bytes_retransmit=0 bytes_invalid=0 send_seq=8527 receive_seq=8527 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998691 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=46.7 th1: temp=46.2 th2: temp=51.6 th3: temp=49.2 sysload=0.25 cputime=302.870 memavail=7395252 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3829.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22215842 bytes_read=2981981 bytes_retransmit=9 bytes_invalid=0 send_seq=396478 receive_seq=396478 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015802 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=23980 bytes_read=75857 bytes_retransmit=0 bytes_invalid=0 send_seq=3968 receive_seq=3968 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997249 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=142073 bytes_read=4382422 bytes_retransmit=9 bytes_invalid=0 send_seq=19241 receive_seq=19241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997854 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84369 bytes_read=1937049 bytes_retransmit=9 bytes_invalid=0 send_seq=11088 receive_seq=11088 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=24247 bytes_read=975447 bytes_retransmit=9 bytes_invalid=0 send_seq=3982 receive_seq=3982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24733 bytes_read=74391 bytes_retransmit=9 bytes_invalid=0 send_seq=3969 receive_seq=3969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78825 bytes_read=1591519 bytes_retransmit=0 bytes_invalid=0 send_seq=8528 receive_seq=8528 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998683 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=46.6 th1: temp=45.7 th2: temp=51.5 th3: temp=49.2 sysload=0.25 cputime=302.913 memavail=7395252 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 3830.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22216140 bytes_read=2982450 bytes_retransmit=9 bytes_invalid=0 send_seq=396501 receive_seq=396501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015812 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23986 bytes_read=75886 bytes_retransmit=0 bytes_invalid=0 send_seq=3969 receive_seq=3969 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997231 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=142079 bytes_read=4382550 bytes_retransmit=9 bytes_invalid=0 send_seq=19242 receive_seq=19242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997805 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84375 bytes_read=1937177 bytes_retransmit=9 bytes_invalid=0 send_seq=11089 receive_seq=11089 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997515 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=24253 bytes_read=975741 bytes_retransmit=9 bytes_invalid=0 send_seq=3983 receive_seq=3983 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997649 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24739 bytes_read=74407 bytes_retransmit=9 bytes_invalid=0 send_seq=3970 receive_seq=3970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78831 bytes_read=1591875 bytes_retransmit=0 bytes_invalid=0 send_seq=8529 receive_seq=8529 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998666 coil_temp=17.2 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.8 th2: temp=51.6 th3: temp=49.2 sysload=0.25 cputime=302.956 memavail=7395252 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.7 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3831.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22216438 bytes_read=2982875 bytes_retransmit=9 bytes_invalid=0 send_seq=396524 receive_seq=396524 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015814 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23992 bytes_read=75902 bytes_retransmit=0 bytes_invalid=0 send_seq=3970 receive_seq=3970 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997211 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142085 bytes_read=4382664 bytes_retransmit=9 bytes_invalid=0 send_seq=19243 receive_seq=19243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997714 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84381 bytes_read=1937277 bytes_retransmit=9 bytes_invalid=0 send_seq=11090 receive_seq=11090 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997491 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=24259 bytes_read=975975 bytes_retransmit=9 bytes_invalid=0 send_seq=3984 receive_seq=3984 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24745 bytes_read=74423 bytes_retransmit=9 bytes_invalid=0 send_seq=3971 receive_seq=3971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78837 bytes_read=1592231 bytes_retransmit=0 bytes_invalid=0 send_seq=8530 receive_seq=8530 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998647 coil_temp=17.2 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=46.6 th1: temp=46.0 th2: temp=51.7 th3: temp=49.2 sysload=0.25 cputime=303.000 memavail=7395252 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3832.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22216736 bytes_read=2983296 bytes_retransmit=9 bytes_invalid=0 send_seq=396547 receive_seq=396547 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015821 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=23998 bytes_read=75918 bytes_retransmit=0 bytes_invalid=0 send_seq=3971 receive_seq=3971 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997197 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142091 bytes_read=4382764 bytes_retransmit=9 bytes_invalid=0 send_seq=19244 receive_seq=19244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997672 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84387 bytes_read=1937377 bytes_retransmit=9 bytes_invalid=0 send_seq=11091 receive_seq=11091 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997488 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=24265 bytes_read=976224 bytes_retransmit=9 bytes_invalid=0 send_seq=3985 receive_seq=3985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24751 bytes_read=74450 bytes_retransmit=9 bytes_invalid=0 send_seq=3972 receive_seq=3972 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78843 bytes_read=1592587 bytes_retransmit=0 bytes_invalid=0 send_seq=8531 receive_seq=8531 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998644 coil_temp=17.2 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.8 th2: temp=51.9 th3: temp=49.2 sysload=0.25 cputime=303.044 memavail=7395252 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 3833.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22217034 bytes_read=2983749 bytes_retransmit=9 bytes_invalid=0 send_seq=396570 receive_seq=396570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015846 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=24004 bytes_read=75934 bytes_retransmit=0 bytes_invalid=0 send_seq=3972 receive_seq=3972 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997199 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142097 bytes_read=4382892 bytes_retransmit=9 bytes_invalid=0 send_seq=19245 receive_seq=19245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997625 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84393 bytes_read=1937505 bytes_retransmit=9 bytes_invalid=0 send_seq=11092 receive_seq=11092 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997473 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=24271 bytes_read=976518 bytes_retransmit=9 bytes_invalid=0 send_seq=3986 receive_seq=3986 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997616 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24757 bytes_read=74466 bytes_retransmit=9 bytes_invalid=0 send_seq=3973 receive_seq=3973 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78849 bytes_read=1592943 bytes_retransmit=0 bytes_invalid=0 send_seq=8532 receive_seq=8532 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998630 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=47.0 th1: temp=45.6 th2: temp=51.7 th3: temp=49.2 sysload=0.23 cputime=303.089 memavail=7395252 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3834.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22217327 bytes_read=2984169 bytes_retransmit=9 bytes_invalid=0 send_seq=396592 receive_seq=396592 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015844 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=24010 bytes_read=75950 bytes_retransmit=0 bytes_invalid=0 send_seq=3973 receive_seq=3973 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997175 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142103 bytes_read=4382992 bytes_retransmit=9 bytes_invalid=0 send_seq=19246 receive_seq=19246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997552 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84399 bytes_read=1937619 bytes_retransmit=9 bytes_invalid=0 send_seq=11093 receive_seq=11093 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997417 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=24277 bytes_read=976752 bytes_retransmit=9 bytes_invalid=0 send_seq=3987 receive_seq=3987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997582 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24763 bytes_read=74482 bytes_retransmit=9 bytes_invalid=0 send_seq=3974 receive_seq=3974 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78855 bytes_read=1593299 bytes_retransmit=0 bytes_invalid=0 send_seq=8533 receive_seq=8533 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998598 coil_temp=17.2 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=46.5 th1: temp=45.8 th2: temp=51.5 th3: temp=49.2 sysload=0.23 cputime=303.131 memavail=7395252 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3835.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22217625 bytes_read=2984609 bytes_retransmit=9 bytes_invalid=0 send_seq=396615 receive_seq=396615 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015844 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=24016 bytes_read=75979 bytes_retransmit=0 bytes_invalid=0 send_seq=3974 receive_seq=3974 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997192 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142109 bytes_read=4383092 bytes_retransmit=9 bytes_invalid=0 send_seq=19247 receive_seq=19247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997579 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84405 bytes_read=1937719 bytes_retransmit=9 bytes_invalid=0 send_seq=11094 receive_seq=11094 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997440 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=24283 bytes_read=976986 bytes_retransmit=9 bytes_invalid=0 send_seq=3988 receive_seq=3988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997595 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24769 bytes_read=74498 bytes_retransmit=9 bytes_invalid=0 send_seq=3975 receive_seq=3975 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999431 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78861 bytes_read=1593655 bytes_retransmit=0 bytes_invalid=0 send_seq=8534 receive_seq=8534 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998615 coil_temp=17.2 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=46.6 th1: temp=45.8 th2: temp=51.6 th3: temp=49.1 sysload=0.23 cputime=303.174 memavail=7395252 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 3836.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22217923 bytes_read=2985063 bytes_retransmit=9 bytes_invalid=0 send_seq=396638 receive_seq=396638 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015846 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=24022 bytes_read=75995 bytes_retransmit=0 bytes_invalid=0 send_seq=3975 receive_seq=3975 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997215 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142115 bytes_read=4383234 bytes_retransmit=9 bytes_invalid=0 send_seq=19248 receive_seq=19248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997574 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84411 bytes_read=1937847 bytes_retransmit=9 bytes_invalid=0 send_seq=11095 receive_seq=11095 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997462 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=24289 bytes_read=977280 bytes_retransmit=9 bytes_invalid=0 send_seq=3989 receive_seq=3989 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997616 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24775 bytes_read=74514 bytes_retransmit=9 bytes_invalid=0 send_seq=3976 receive_seq=3976 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78867 bytes_read=1594011 bytes_retransmit=0 bytes_invalid=0 send_seq=8535 receive_seq=8535 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998619 coil_temp=17.2 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=46.4 th1: temp=45.8 th2: temp=51.5 th3: temp=49.3 sysload=0.23 cputime=303.217 memavail=7393780 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3837.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22218221 bytes_read=2985488 bytes_retransmit=9 bytes_invalid=0 send_seq=396661 receive_seq=396661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015851 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=24028 bytes_read=76011 bytes_retransmit=0 bytes_invalid=0 send_seq=3976 receive_seq=3976 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997214 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142121 bytes_read=4383334 bytes_retransmit=9 bytes_invalid=0 send_seq=19249 receive_seq=19249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997574 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84417 bytes_read=1937947 bytes_retransmit=9 bytes_invalid=0 send_seq=11096 receive_seq=11096 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997475 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24295 bytes_read=977529 bytes_retransmit=9 bytes_invalid=0 send_seq=3990 receive_seq=3990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997634 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24781 bytes_read=74541 bytes_retransmit=9 bytes_invalid=0 send_seq=3977 receive_seq=3977 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78873 bytes_read=1594367 bytes_retransmit=0 bytes_invalid=0 send_seq=8536 receive_seq=8536 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998625 coil_temp=17.2 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=46.8 th1: temp=45.8 th2: temp=51.7 th3: temp=49.1 sysload=0.23 cputime=303.260 memavail=7393832 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Stats 3838.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22218514 bytes_read=2985908 bytes_retransmit=9 bytes_invalid=0 send_seq=396683 receive_seq=396683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015851 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=24034 bytes_read=76027 bytes_retransmit=0 bytes_invalid=0 send_seq=3977 receive_seq=3977 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997201 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142127 bytes_read=4383434 bytes_retransmit=9 bytes_invalid=0 send_seq=19250 receive_seq=19250 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997569 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84423 bytes_read=1938047 bytes_retransmit=9 bytes_invalid=0 send_seq=11097 receive_seq=11097 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997481 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24301 bytes_read=977763 bytes_retransmit=9 bytes_invalid=0 send_seq=3991 receive_seq=3991 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24787 bytes_read=74557 bytes_retransmit=9 bytes_invalid=0 send_seq=3978 receive_seq=3978 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78879 bytes_read=1594723 bytes_retransmit=0 bytes_invalid=0 send_seq=8537 receive_seq=8537 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998641 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=46.6 th1: temp=46.0 th2: temp=51.5 th3: temp=49.2 sysload=0.21 cputime=303.302 memavail=7393832 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3839.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22218807 bytes_read=2986357 bytes_retransmit=9 bytes_invalid=0 send_seq=396705 receive_seq=396705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015853 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=24040 bytes_read=76043 bytes_retransmit=0 bytes_invalid=0 send_seq=3978 receive_seq=3978 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997212 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142133 bytes_read=4383562 bytes_retransmit=9 bytes_invalid=0 send_seq=19251 receive_seq=19251 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997589 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84429 bytes_read=1938189 bytes_retransmit=9 bytes_invalid=0 send_seq=11098 receive_seq=11098 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997488 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24307 bytes_read=978057 bytes_retransmit=9 bytes_invalid=0 send_seq=3992 receive_seq=3992 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24793 bytes_read=74573 bytes_retransmit=9 bytes_invalid=0 send_seq=3979 receive_seq=3979 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78885 bytes_read=1595079 bytes_retransmit=0 bytes_invalid=0 send_seq=8538 receive_seq=8538 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998708 coil_temp=17.2 refs=0 mcu_temp=20.36 supply_voltage=3.012 th0: temp=46.5 th1: temp=45.8 th2: temp=51.8 th3: temp=49.2 sysload=0.21 cputime=303.349 memavail=7387560 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
Stats 3840.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22219105 bytes_read=2986797 bytes_retransmit=9 bytes_invalid=0 send_seq=396728 receive_seq=396728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015863 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=24046 bytes_read=76072 bytes_retransmit=0 bytes_invalid=0 send_seq=3979 receive_seq=3979 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997211 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142139 bytes_read=4383662 bytes_retransmit=9 bytes_invalid=0 send_seq=19252 receive_seq=19252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997581 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84435 bytes_read=1938289 bytes_retransmit=9 bytes_invalid=0 send_seq=11099 receive_seq=11099 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997487 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24313 bytes_read=978291 bytes_retransmit=9 bytes_invalid=0 send_seq=3993 receive_seq=3993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997632 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24799 bytes_read=74589 bytes_retransmit=9 bytes_invalid=0 send_seq=3980 receive_seq=3980 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78891 bytes_read=1595435 bytes_retransmit=0 bytes_invalid=0 send_seq=8539 receive_seq=8539 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998680 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.8 th2: temp=51.6 th3: temp=49.2 sysload=0.21 cputime=303.392 memavail=7394212 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3841.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22219388 bytes_read=2987207 bytes_retransmit=9 bytes_invalid=0 send_seq=396748 receive_seq=396748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015863 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=24052 bytes_read=76088 bytes_retransmit=0 bytes_invalid=0 send_seq=3980 receive_seq=3980 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999213 adj=49997224 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142145 bytes_read=4383776 bytes_retransmit=9 bytes_invalid=0 send_seq=19253 receive_seq=19253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997593 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84441 bytes_read=1938389 bytes_retransmit=9 bytes_invalid=0 send_seq=11100 receive_seq=11100 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997471 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24319 bytes_read=978525 bytes_retransmit=9 bytes_invalid=0 send_seq=3994 receive_seq=3994 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997615 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24805 bytes_read=74605 bytes_retransmit=9 bytes_invalid=0 send_seq=3981 receive_seq=3981 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78897 bytes_read=1595791 bytes_retransmit=0 bytes_invalid=0 send_seq=8540 receive_seq=8540 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998656 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=46.4 th1: temp=45.5 th2: temp=51.9 th3: temp=49.4 sysload=0.21 cputime=303.433 memavail=7394212 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3842.3: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22219686 bytes_read=2987661 bytes_retransmit=9 bytes_invalid=0 send_seq=396771 receive_seq=396771 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015868 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=24058 bytes_read=76104 bytes_retransmit=0 bytes_invalid=0 send_seq=3981 receive_seq=3981 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997218 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142151 bytes_read=4383904 bytes_retransmit=9 bytes_invalid=0 send_seq=19254 receive_seq=19254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997602 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84447 bytes_read=1938517 bytes_retransmit=9 bytes_invalid=0 send_seq=11101 receive_seq=11101 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997478 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24325 bytes_read=978834 bytes_retransmit=9 bytes_invalid=0 send_seq=3995 receive_seq=3995 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24811 bytes_read=74632 bytes_retransmit=9 bytes_invalid=0 send_seq=3982 receive_seq=3982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78903 bytes_read=1596147 bytes_retransmit=0 bytes_invalid=0 send_seq=8541 receive_seq=8541 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998654 coil_temp=17.2 refs=0 mcu_temp=20.36 supply_voltage=3.012 th0: temp=46.4 th1: temp=45.7 th2: temp=51.6 th3: temp=49.4 sysload=0.21 cputime=303.478 memavail=7394212 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3843.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22219984 bytes_read=2988082 bytes_retransmit=9 bytes_invalid=0 send_seq=396794 receive_seq=396794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015867 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=24064 bytes_read=76120 bytes_retransmit=0 bytes_invalid=0 send_seq=3982 receive_seq=3982 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999211 adj=49997199 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142157 bytes_read=4384004 bytes_retransmit=9 bytes_invalid=0 send_seq=19255 receive_seq=19255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997675 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84453 bytes_read=1938617 bytes_retransmit=9 bytes_invalid=0 send_seq=11102 receive_seq=11102 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997474 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24331 bytes_read=979068 bytes_retransmit=9 bytes_invalid=0 send_seq=3996 receive_seq=3996 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997610 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24817 bytes_read=74648 bytes_retransmit=9 bytes_invalid=0 send_seq=3983 receive_seq=3983 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78909 bytes_read=1596503 bytes_retransmit=0 bytes_invalid=0 send_seq=8542 receive_seq=8542 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998649 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.012 th0: temp=46.6 th1: temp=45.8 th2: temp=51.5 th3: temp=49.3 sysload=0.19 cputime=303.522 memavail=7394212 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Stats 3844.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22220282 bytes_read=2988507 bytes_retransmit=9 bytes_invalid=0 send_seq=396817 receive_seq=396817 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015894 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=24070 bytes_read=76136 bytes_retransmit=0 bytes_invalid=0 send_seq=3983 receive_seq=3983 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997189 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142163 bytes_read=4384118 bytes_retransmit=9 bytes_invalid=0 send_seq=19256 receive_seq=19256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997714 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84459 bytes_read=1938731 bytes_retransmit=9 bytes_invalid=0 send_seq=11103 receive_seq=11103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997486 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24337 bytes_read=979302 bytes_retransmit=9 bytes_invalid=0 send_seq=3997 receive_seq=3997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24823 bytes_read=74664 bytes_retransmit=9 bytes_invalid=0 send_seq=3984 receive_seq=3984 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78915 bytes_read=1596859 bytes_retransmit=0 bytes_invalid=0 send_seq=8543 receive_seq=8543 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998662 coil_temp=17.2 refs=0 mcu_temp=20.37 supply_voltage=3.012 th0: temp=46.8 th1: temp=45.7 th2: temp=51.7 th3: temp=49.3 sysload=0.19 cputime=303.568 memavail=7393960 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3845.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22220580 bytes_read=2988976 bytes_retransmit=9 bytes_invalid=0 send_seq=396840 receive_seq=396840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015890 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=24076 bytes_read=76165 bytes_retransmit=0 bytes_invalid=0 send_seq=3984 receive_seq=3984 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997125 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142169 bytes_read=4384232 bytes_retransmit=9 bytes_invalid=0 send_seq=19257 receive_seq=19257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997610 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84465 bytes_read=1938859 bytes_retransmit=9 bytes_invalid=0 send_seq=11104 receive_seq=11104 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997418 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24343 bytes_read=979596 bytes_retransmit=9 bytes_invalid=0 send_seq=3998 receive_seq=3998 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997573 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24829 bytes_read=74680 bytes_retransmit=9 bytes_invalid=0 send_seq=3985 receive_seq=3985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78921 bytes_read=1597215 bytes_retransmit=0 bytes_invalid=0 send_seq=8544 receive_seq=8544 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998625 coil_temp=17.2 refs=0 mcu_temp=20.36 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.7 th2: temp=51.6 th3: temp=49.3 sysload=0.19 cputime=303.614 memavail=7393960 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3846.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22220878 bytes_read=2989401 bytes_retransmit=9 bytes_invalid=0 send_seq=396863 receive_seq=396863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015902 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=24082 bytes_read=76181 bytes_retransmit=0 bytes_invalid=0 send_seq=3985 receive_seq=3985 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997150 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142175 bytes_read=4384332 bytes_retransmit=9 bytes_invalid=0 send_seq=19258 receive_seq=19258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997643 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84471 bytes_read=1938959 bytes_retransmit=9 bytes_invalid=0 send_seq=11105 receive_seq=11105 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997464 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24349 bytes_read=979830 bytes_retransmit=9 bytes_invalid=0 send_seq=3999 receive_seq=3999 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997593 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24835 bytes_read=74696 bytes_retransmit=9 bytes_invalid=0 send_seq=3986 receive_seq=3986 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78927 bytes_read=1597571 bytes_retransmit=0 bytes_invalid=0 send_seq=8545 receive_seq=8545 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998643 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.6 th2: temp=51.7 th3: temp=49.2 sysload=0.19 cputime=303.659 memavail=7393720 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.6 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3847.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22221176 bytes_read=2989826 bytes_retransmit=9 bytes_invalid=0 send_seq=396886 receive_seq=396886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015899 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=24088 bytes_read=76197 bytes_retransmit=0 bytes_invalid=0 send_seq=3986 receive_seq=3986 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999209 adj=49997149 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142181 bytes_read=4384460 bytes_retransmit=9 bytes_invalid=0 send_seq=19259 receive_seq=19259 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997604 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84477 bytes_read=1939059 bytes_retransmit=9 bytes_invalid=0 send_seq=11106 receive_seq=11106 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997442 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24355 bytes_read=980079 bytes_retransmit=9 bytes_invalid=0 send_seq=4000 receive_seq=4000 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997594 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24841 bytes_read=74723 bytes_retransmit=9 bytes_invalid=0 send_seq=3987 receive_seq=3987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78933 bytes_read=1597927 bytes_retransmit=0 bytes_invalid=0 send_seq=8546 receive_seq=8546 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998629 coil_temp=17.2 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=46.6 th1: temp=45.6 th2: temp=51.6 th3: temp=49.2 sysload=0.19 cputime=303.704 memavail=7393728 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3848.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22221474 bytes_read=2990280 bytes_retransmit=9 bytes_invalid=0 send_seq=396909 receive_seq=396909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015895 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=24094 bytes_read=76213 bytes_retransmit=0 bytes_invalid=0 send_seq=3987 receive_seq=3987 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997174 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142187 bytes_read=4384574 bytes_retransmit=9 bytes_invalid=0 send_seq=19260 receive_seq=19260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997633 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84483 bytes_read=1939187 bytes_retransmit=9 bytes_invalid=0 send_seq=11107 receive_seq=11107 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997461 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24361 bytes_read=980373 bytes_retransmit=9 bytes_invalid=0 send_seq=4001 receive_seq=4001 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997607 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24847 bytes_read=74739 bytes_retransmit=9 bytes_invalid=0 send_seq=3988 receive_seq=3988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78939 bytes_read=1598283 bytes_retransmit=0 bytes_invalid=0 send_seq=8547 receive_seq=8547 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998648 coil_temp=17.2 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=46.7 th1: temp=45.7 th2: temp=51.7 th3: temp=49.4 sysload=0.18 cputime=303.746 memavail=7393728 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3849.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22221772 bytes_read=2990705 bytes_retransmit=9 bytes_invalid=0 send_seq=396932 receive_seq=396932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015894 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=24100 bytes_read=76229 bytes_retransmit=0 bytes_invalid=0 send_seq=3988 receive_seq=3988 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999210 adj=49997199 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142193 bytes_read=4384674 bytes_retransmit=9 bytes_invalid=0 send_seq=19261 receive_seq=19261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997709 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84489 bytes_read=1939301 bytes_retransmit=9 bytes_invalid=0 send_seq=11108 receive_seq=11108 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997483 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24367 bytes_read=980607 bytes_retransmit=9 bytes_invalid=0 send_seq=4002 receive_seq=4002 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997621 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24853 bytes_read=74755 bytes_retransmit=9 bytes_invalid=0 send_seq=3989 receive_seq=3989 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78945 bytes_read=1598636 bytes_retransmit=0 bytes_invalid=0 send_seq=8548 receive_seq=8548 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998679 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=46.9 th1: temp=45.7 th2: temp=51.9 th3: temp=49.3 sysload=0.18 cputime=303.790 memavail=7393728 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 3850.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22222076 bytes_read=2991161 bytes_retransmit=9 bytes_invalid=0 send_seq=396956 receive_seq=396956 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015911 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=24112 bytes_read=76274 bytes_retransmit=0 bytes_invalid=0 send_seq=3990 receive_seq=3990 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997216 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142205 bytes_read=4384804 bytes_retransmit=9 bytes_invalid=0 send_seq=19263 receive_seq=19263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997727 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84501 bytes_read=1939431 bytes_retransmit=9 bytes_invalid=0 send_seq=11110 receive_seq=11110 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24379 bytes_read=980857 bytes_retransmit=9 bytes_invalid=0 send_seq=4004 receive_seq=4004 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24865 bytes_read=74787 bytes_retransmit=9 bytes_invalid=0 send_seq=3991 receive_seq=3991 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78957 bytes_read=1598996 bytes_retransmit=0 bytes_invalid=0 send_seq=8550 receive_seq=8550 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998710 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=46.3 th1: temp=45.6 th2: temp=51.6 th3: temp=49.4 sysload=0.18 cputime=303.835 memavail=7393728 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Stats 3851.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22222369 bytes_read=2991610 bytes_retransmit=9 bytes_invalid=0 send_seq=396978 receive_seq=396978 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015908 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=24118 bytes_read=76290 bytes_retransmit=0 bytes_invalid=0 send_seq=3991 receive_seq=3991 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997210 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142211 bytes_read=4384918 bytes_retransmit=9 bytes_invalid=0 send_seq=19264 receive_seq=19264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997617 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84507 bytes_read=1939545 bytes_retransmit=9 bytes_invalid=0 send_seq=11111 receive_seq=11111 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24385 bytes_read=981151 bytes_retransmit=9 bytes_invalid=0 send_seq=4005 receive_seq=4005 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997700 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24871 bytes_read=74803 bytes_retransmit=9 bytes_invalid=0 send_seq=3992 receive_seq=3992 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78963 bytes_read=1599340 bytes_retransmit=0 bytes_invalid=0 send_seq=8551 receive_seq=8551 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998655 coil_temp=17.2 refs=0 mcu_temp=20.32 supply_voltage=3.012 th0: temp=46.6 th1: temp=45.8 th2: temp=51.5 th3: temp=49.3 sysload=0.18 cputime=303.878 memavail=7393748 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.7 pwm=0.000
Stats 3852.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22222667 bytes_read=2992035 bytes_retransmit=9 bytes_invalid=0 send_seq=397001 receive_seq=397001 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015904 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=24124 bytes_read=76306 bytes_retransmit=0 bytes_invalid=0 send_seq=3992 receive_seq=3992 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997219 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142217 bytes_read=4385032 bytes_retransmit=9 bytes_invalid=0 send_seq=19265 receive_seq=19265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997614 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84513 bytes_read=1939645 bytes_retransmit=9 bytes_invalid=0 send_seq=11112 receive_seq=11112 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997485 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24391 bytes_read=981400 bytes_retransmit=9 bytes_invalid=0 send_seq=4006 receive_seq=4006 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24877 bytes_read=74830 bytes_retransmit=9 bytes_invalid=0 send_seq=3993 receive_seq=3993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78969 bytes_read=1599685 bytes_retransmit=0 bytes_invalid=0 send_seq=8552 receive_seq=8552 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998683 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=46.6 th1: temp=45.8 th2: temp=51.8 th3: temp=49.4 sysload=0.18 cputime=303.921 memavail=7393748 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 3853.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22222965 bytes_read=2992460 bytes_retransmit=9 bytes_invalid=0 send_seq=397024 receive_seq=397024 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015909 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=24130 bytes_read=76322 bytes_retransmit=0 bytes_invalid=0 send_seq=3993 receive_seq=3993 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997236 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142223 bytes_read=4385146 bytes_retransmit=9 bytes_invalid=0 send_seq=19266 receive_seq=19266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997608 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=84519 bytes_read=1939759 bytes_retransmit=9 bytes_invalid=0 send_seq=11113 receive_seq=11113 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997497 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24397 bytes_read=981634 bytes_retransmit=9 bytes_invalid=0 send_seq=4007 receive_seq=4007 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24883 bytes_read=74846 bytes_retransmit=9 bytes_invalid=0 send_seq=3994 receive_seq=3994 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.7  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78975 bytes_read=1600030 bytes_retransmit=0 bytes_invalid=0 send_seq=8553 receive_seq=8553 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998677 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=46.6 th1: temp=45.7 th2: temp=51.6 th3: temp=49.3 sysload=0.16 cputime=303.965 memavail=7393748 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Stats 3854.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22223263 bytes_read=2992910 bytes_retransmit=9 bytes_invalid=0 send_seq=397047 receive_seq=397047 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015919 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=24136 bytes_read=76338 bytes_retransmit=0 bytes_invalid=0 send_seq=3994 receive_seq=3994 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49997225 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=142229 bytes_read=4385260 bytes_retransmit=9 bytes_invalid=0 send_seq=19267 receive_seq=19267 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997714 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=84525 bytes_read=1939887 bytes_retransmit=9 bytes_invalid=0 send_seq=11114 receive_seq=11114 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997488 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=24403 bytes_read=981928 bytes_retransmit=9 bytes_invalid=0 send_seq=4008 receive_seq=4008 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=24889 bytes_read=74862 bytes_retransmit=9 bytes_invalid=0 send_seq=3995 receive_seq=3995 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=78981 bytes_read=1600375 bytes_retransmit=0 bytes_invalid=0 send_seq=8554 receive_seq=8554 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998652 coil_temp=17.2 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=46.5 th1: temp=45.8 th2: temp=51.9 th3: temp=49.3 sysload=0.16 cputime=304.010 memavail=7393752 print_time=3817.688 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.6 pwm=0.000
RatOS:: Toolhead remapping deactivated!
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
RatOS:: All requested axes already homed. Skipping homing.
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Probing point (250.000, 250.000, 20.000)
Stats 5039.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22575404 bytes_read=3509200 bytes_retransmit=9 bytes_invalid=0 send_seq=423967 receive_seq=423967 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015860 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=31354 bytes_read=98564 bytes_retransmit=0 bytes_invalid=0 send_seq=5197 receive_seq=5197 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997355 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=149447 bytes_read=4517772 bytes_retransmit=9 bytes_invalid=0 send_seq=20470 receive_seq=20470 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997678 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91743 bytes_read=2072384 bytes_retransmit=9 bytes_invalid=0 send_seq=12317 receive_seq=12317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997568 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31621 bytes_read=1285393 bytes_retransmit=9 bytes_invalid=0 send_seq=5211 receive_seq=5211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997709 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32107 bytes_read=96648 bytes_retransmit=9 bytes_invalid=0 send_seq=5198 receive_seq=5198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999475 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86199 bytes_read=2021236 bytes_retransmit=0 bytes_invalid=0 send_seq=9757 receive_seq=9757 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998740 coil_temp=16.9 refs=0 mcu_temp=20.16 supply_voltage=3.011 th0: temp=50.7 th1: temp=49.6 th2: temp=57.3 th3: temp=55.0 sysload=0.20 cputime=355.474 memavail=7391708 print_time=5062.157 buffer_time=0.476 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t0' measurements
toolhead: max_velocity: 600.000000
max_accel: 8379.841000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance testing
Testing frequency 10 Hz
Testing frequency 11 Hz
Testing frequency 12 Hz
Stats 5040.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22578568 bytes_read=3509860 bytes_retransmit=9 bytes_invalid=0 send_seq=424037 receive_seq=424037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015851 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=31360 bytes_read=98580 bytes_retransmit=0 bytes_invalid=0 send_seq=5198 receive_seq=5198 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997331 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=149588 bytes_read=4519222 bytes_retransmit=9 bytes_invalid=0 send_seq=20486 receive_seq=20486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997675 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=91749 bytes_read=2072498 bytes_retransmit=9 bytes_invalid=0 send_seq=12318 receive_seq=12318 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997553 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31627 bytes_read=1285627 bytes_retransmit=9 bytes_invalid=0 send_seq=5212 receive_seq=5212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32113 bytes_read=96664 bytes_retransmit=9 bytes_invalid=0 send_seq=5199 receive_seq=5199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999463 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86205 bytes_read=2021592 bytes_retransmit=0 bytes_invalid=0 send_seq=9758 receive_seq=9758 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998705 coil_temp=16.9 refs=0 mcu_temp=20.16 supply_voltage=3.011 th0: temp=50.9 th1: temp=49.3 th2: temp=57.4 th3: temp=55.1 sysload=0.18 cputime=355.635 memavail=7391708 print_time=5065.361 buffer_time=2.677 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5041.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22579511 bytes_read=3510374 bytes_retransmit=9 bytes_invalid=0 send_seq=424069 receive_seq=424069 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015842 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=31366 bytes_read=98596 bytes_retransmit=0 bytes_invalid=0 send_seq=5199 receive_seq=5199 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997284 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=149664 bytes_read=4522307 bytes_retransmit=9 bytes_invalid=0 send_seq=20497 receive_seq=20497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997681 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=91755 bytes_read=2072626 bytes_retransmit=9 bytes_invalid=0 send_seq=12319 receive_seq=12319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31633 bytes_read=1285876 bytes_retransmit=9 bytes_invalid=0 send_seq=5213 receive_seq=5213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32119 bytes_read=96680 bytes_retransmit=9 bytes_invalid=0 send_seq=5200 receive_seq=5200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86211 bytes_read=2021948 bytes_retransmit=0 bytes_invalid=0 send_seq=9759 receive_seq=9759 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998689 coil_temp=16.9 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=51.0 th1: temp=49.9 th2: temp=57.4 th3: temp=54.8 sysload=0.18 cputime=355.701 memavail=7391708 print_time=5065.955 buffer_time=2.269 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 13 Hz
Stats 5042.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22580598 bytes_read=3510849 bytes_retransmit=9 bytes_invalid=0 send_seq=424102 receive_seq=424102 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015836 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31372 bytes_read=98625 bytes_retransmit=0 bytes_invalid=0 send_seq=5200 receive_seq=5200 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997299 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=149740 bytes_read=4525333 bytes_retransmit=9 bytes_invalid=0 send_seq=20508 receive_seq=20508 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997731 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=91761 bytes_read=2072726 bytes_retransmit=9 bytes_invalid=0 send_seq=12320 receive_seq=12320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997530 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31639 bytes_read=1286155 bytes_retransmit=9 bytes_invalid=0 send_seq=5214 receive_seq=5214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32125 bytes_read=96707 bytes_retransmit=9 bytes_invalid=0 send_seq=5201 receive_seq=5201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999453 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86217 bytes_read=2022304 bytes_retransmit=0 bytes_invalid=0 send_seq=9760 receive_seq=9760 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998690 coil_temp=16.9 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=50.7 th1: temp=49.8 th2: temp=57.4 th3: temp=55.0 sysload=0.18 cputime=355.770 memavail=7391708 print_time=5066.798 buffer_time=2.109 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 14 Hz
Stats 5043.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22582119 bytes_read=3511359 bytes_retransmit=9 bytes_invalid=0 send_seq=424142 receive_seq=424142 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015831 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31378 bytes_read=98641 bytes_retransmit=0 bytes_invalid=0 send_seq=5201 receive_seq=5201 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997310 toolboard_t0: mcu_awake=0.194 mcu_task_avg=0.000113 mcu_task_stddev=0.000071 bytes_write=149816 bytes_read=4528406 bytes_retransmit=9 bytes_invalid=0 send_seq=20519 receive_seq=20519 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997814 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=91767 bytes_read=2072826 bytes_retransmit=9 bytes_invalid=0 send_seq=12321 receive_seq=12321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997536 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31645 bytes_read=1286404 bytes_retransmit=9 bytes_invalid=0 send_seq=5215 receive_seq=5215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32131 bytes_read=96723 bytes_retransmit=9 bytes_invalid=0 send_seq=5202 receive_seq=5202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999453 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86223 bytes_read=2022678 bytes_retransmit=0 bytes_invalid=0 send_seq=9761 receive_seq=9761 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998691 coil_temp=16.9 refs=0 mcu_temp=20.18 supply_voltage=3.011 th0: temp=51.2 th1: temp=49.8 th2: temp=57.4 th3: temp=54.9 sysload=0.18 cputime=355.843 memavail=7391708 print_time=5067.796 buffer_time=2.106 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 15 Hz
Stats 5044.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22583380 bytes_read=3511863 bytes_retransmit=9 bytes_invalid=0 send_seq=424175 receive_seq=424175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015820 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31384 bytes_read=98657 bytes_retransmit=0 bytes_invalid=0 send_seq=5202 receive_seq=5202 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997313 toolboard_t0: mcu_awake=0.194 mcu_task_avg=0.000113 mcu_task_stddev=0.000071 bytes_write=149892 bytes_read=4531491 bytes_retransmit=9 bytes_invalid=0 send_seq=20530 receive_seq=20530 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997906 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=91773 bytes_read=2072954 bytes_retransmit=9 bytes_invalid=0 send_seq=12322 receive_seq=12322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997535 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31651 bytes_read=1286668 bytes_retransmit=9 bytes_invalid=0 send_seq=5216 receive_seq=5216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32137 bytes_read=96739 bytes_retransmit=9 bytes_invalid=0 send_seq=5203 receive_seq=5203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86229 bytes_read=2023034 bytes_retransmit=0 bytes_invalid=0 send_seq=9762 receive_seq=9762 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998687 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=51.3 th1: temp=50.1 th2: temp=57.6 th3: temp=55.1 sysload=0.18 cputime=355.915 memavail=7391712 print_time=5068.715 buffer_time=2.022 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 16 Hz
Stats 5045.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22585122 bytes_read=3512393 bytes_retransmit=9 bytes_invalid=0 send_seq=424219 receive_seq=424219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015827 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31390 bytes_read=98673 bytes_retransmit=0 bytes_invalid=0 send_seq=5203 receive_seq=5203 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997327 toolboard_t0: mcu_awake=0.194 mcu_task_avg=0.000113 mcu_task_stddev=0.000071 bytes_write=149968 bytes_read=4534550 bytes_retransmit=9 bytes_invalid=0 send_seq=20541 receive_seq=20541 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997869 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91779 bytes_read=2073068 bytes_retransmit=9 bytes_invalid=0 send_seq=12323 receive_seq=12323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997549 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31657 bytes_read=1286932 bytes_retransmit=9 bytes_invalid=0 send_seq=5217 receive_seq=5217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997677 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32143 bytes_read=96755 bytes_retransmit=9 bytes_invalid=0 send_seq=5204 receive_seq=5204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999453 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86235 bytes_read=2023390 bytes_retransmit=0 bytes_invalid=0 send_seq=9763 receive_seq=9763 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998683 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=51.1 th1: temp=50.1 th2: temp=57.6 th3: temp=55.1 sysload=0.17 cputime=355.990 memavail=7391732 print_time=5069.927 buffer_time=2.232 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 17 Hz
Stats 5046.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22586729 bytes_read=3512928 bytes_retransmit=9 bytes_invalid=0 send_seq=424262 receive_seq=424262 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015836 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31396 bytes_read=98689 bytes_retransmit=0 bytes_invalid=0 send_seq=5204 receive_seq=5204 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997306 toolboard_t0: mcu_awake=0.194 mcu_task_avg=0.000113 mcu_task_stddev=0.000071 bytes_write=150044 bytes_read=4537669 bytes_retransmit=9 bytes_invalid=0 send_seq=20552 receive_seq=20552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997852 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91785 bytes_read=2073168 bytes_retransmit=9 bytes_invalid=0 send_seq=12324 receive_seq=12324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997521 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31663 bytes_read=1287166 bytes_retransmit=9 bytes_invalid=0 send_seq=5218 receive_seq=5218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32149 bytes_read=96771 bytes_retransmit=9 bytes_invalid=0 send_seq=5205 receive_seq=5205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86241 bytes_read=2023746 bytes_retransmit=0 bytes_invalid=0 send_seq=9764 receive_seq=9764 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998662 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=51.5 th1: temp=50.3 th2: temp=57.7 th3: temp=55.3 sysload=0.17 cputime=356.063 memavail=7391732 print_time=5070.848 buffer_time=2.151 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 18 Hz
Stats 5047.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22588117 bytes_read=3513462 bytes_retransmit=9 bytes_invalid=0 send_seq=424301 receive_seq=424301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015882 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31402 bytes_read=98718 bytes_retransmit=0 bytes_invalid=0 send_seq=5205 receive_seq=5205 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997280 toolboard_t0: mcu_awake=0.194 mcu_task_avg=0.000113 mcu_task_stddev=0.000071 bytes_write=150120 bytes_read=4540753 bytes_retransmit=9 bytes_invalid=0 send_seq=20563 receive_seq=20563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997785 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91791 bytes_read=2073296 bytes_retransmit=9 bytes_invalid=0 send_seq=12325 receive_seq=12325 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31669 bytes_read=1287430 bytes_retransmit=9 bytes_invalid=0 send_seq=5219 receive_seq=5219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32155 bytes_read=96798 bytes_retransmit=9 bytes_invalid=0 send_seq=5206 receive_seq=5206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86247 bytes_read=2024102 bytes_retransmit=0 bytes_invalid=0 send_seq=9765 receive_seq=9765 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998650 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=51.5 th1: temp=50.4 th2: temp=57.7 th3: temp=55.4 sysload=0.17 cputime=356.144 memavail=7392844 print_time=5071.812 buffer_time=2.111 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 19 Hz
Testing frequency 20 Hz
Stats 5048.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22590019 bytes_read=3514007 bytes_retransmit=9 bytes_invalid=0 send_seq=424348 receive_seq=424348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=0 freq=400015885 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31408 bytes_read=98734 bytes_retransmit=0 bytes_invalid=0 send_seq=5206 receive_seq=5206 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997231 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150196 bytes_read=4543826 bytes_retransmit=9 bytes_invalid=0 send_seq=20574 receive_seq=20574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997649 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91797 bytes_read=2073396 bytes_retransmit=9 bytes_invalid=0 send_seq=12326 receive_seq=12326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997400 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31675 bytes_read=1287709 bytes_retransmit=9 bytes_invalid=0 send_seq=5220 receive_seq=5220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997567 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32161 bytes_read=96814 bytes_retransmit=9 bytes_invalid=0 send_seq=5207 receive_seq=5207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999422 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86253 bytes_read=2024458 bytes_retransmit=0 bytes_invalid=0 send_seq=9766 receive_seq=9766 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998601 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=51.5 th1: temp=50.4 th2: temp=57.8 th3: temp=55.6 sysload=0.17 cputime=356.221 memavail=7392844 print_time=5073.001 buffer_time=2.299 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5049.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22591765 bytes_read=3514537 bytes_retransmit=9 bytes_invalid=0 send_seq=424392 receive_seq=424392 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015878 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31414 bytes_read=98750 bytes_retransmit=0 bytes_invalid=0 send_seq=5207 receive_seq=5207 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997240 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150272 bytes_read=4546883 bytes_retransmit=9 bytes_invalid=0 send_seq=20585 receive_seq=20585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997635 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91803 bytes_read=2073496 bytes_retransmit=9 bytes_invalid=0 send_seq=12327 receive_seq=12327 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997426 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31681 bytes_read=1287943 bytes_retransmit=9 bytes_invalid=0 send_seq=5221 receive_seq=5221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997582 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32167 bytes_read=96830 bytes_retransmit=9 bytes_invalid=0 send_seq=5208 receive_seq=5208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999425 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86259 bytes_read=2024814 bytes_retransmit=0 bytes_invalid=0 send_seq=9767 receive_seq=9767 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998613 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=52.3 th1: temp=50.5 th2: temp=57.9 th3: temp=55.4 sysload=0.17 cputime=356.291 memavail=7392844 print_time=5073.873 buffer_time=2.167 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 21 Hz
Stats 5050.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=22593286 bytes_read=3515086 bytes_retransmit=9 bytes_invalid=0 send_seq=424434 receive_seq=424434 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015874 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31420 bytes_read=98766 bytes_retransmit=0 bytes_invalid=0 send_seq=5208 receive_seq=5208 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997252 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150341 bytes_read=4550006 bytes_retransmit=9 bytes_invalid=0 send_seq=20595 receive_seq=20595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997644 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91809 bytes_read=2073638 bytes_retransmit=9 bytes_invalid=0 send_seq=12328 receive_seq=12328 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997447 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31687 bytes_read=1288222 bytes_retransmit=9 bytes_invalid=0 send_seq=5222 receive_seq=5222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997591 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32173 bytes_read=96846 bytes_retransmit=9 bytes_invalid=0 send_seq=5209 receive_seq=5209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999427 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86265 bytes_read=2025170 bytes_retransmit=0 bytes_invalid=0 send_seq=9768 receive_seq=9768 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998617 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=51.8 th1: temp=50.6 th2: temp=57.8 th3: temp=55.7 sysload=0.31 cputime=356.365 memavail=7392844 print_time=5074.823 buffer_time=2.114 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 22 Hz
Testing frequency 23 Hz
Stats 5051.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22595056 bytes_read=3515636 bytes_retransmit=9 bytes_invalid=0 send_seq=424479 receive_seq=424479 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015896 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31426 bytes_read=98782 bytes_retransmit=0 bytes_invalid=0 send_seq=5209 receive_seq=5209 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997261 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150417 bytes_read=4553063 bytes_retransmit=9 bytes_invalid=0 send_seq=20606 receive_seq=20606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997632 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91815 bytes_read=2073738 bytes_retransmit=9 bytes_invalid=0 send_seq=12329 receive_seq=12329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997459 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31693 bytes_read=1288471 bytes_retransmit=9 bytes_invalid=0 send_seq=5223 receive_seq=5223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32179 bytes_read=96862 bytes_retransmit=9 bytes_invalid=0 send_seq=5210 receive_seq=5210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999428 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86271 bytes_read=2025526 bytes_retransmit=0 bytes_invalid=0 send_seq=9769 receive_seq=9769 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998638 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=52.0 th1: temp=50.6 th2: temp=58.0 th3: temp=55.7 sysload=0.31 cputime=356.439 memavail=7392844 print_time=5075.699 buffer_time=1.988 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5052.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22597204 bytes_read=3516201 bytes_retransmit=9 bytes_invalid=0 send_seq=424530 receive_seq=424530 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015886 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31432 bytes_read=98811 bytes_retransmit=0 bytes_invalid=0 send_seq=5210 receive_seq=5210 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997227 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150493 bytes_read=4556120 bytes_retransmit=9 bytes_invalid=0 send_seq=20617 receive_seq=20617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997564 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91821 bytes_read=2073838 bytes_retransmit=9 bytes_invalid=0 send_seq=12330 receive_seq=12330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997425 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31699 bytes_read=1288705 bytes_retransmit=9 bytes_invalid=0 send_seq=5224 receive_seq=5224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997596 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32185 bytes_read=96889 bytes_retransmit=9 bytes_invalid=0 send_seq=5211 receive_seq=5211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999419 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86277 bytes_read=2025882 bytes_retransmit=0 bytes_invalid=0 send_seq=9770 receive_seq=9770 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998610 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=51.8 th1: temp=50.7 th2: temp=58.2 th3: temp=55.6 sysload=0.31 cputime=356.513 memavail=7392844 print_time=5076.902 buffer_time=2.188 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 24 Hz
Stats 5053.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22598904 bytes_read=3516760 bytes_retransmit=9 bytes_invalid=0 send_seq=424574 receive_seq=424574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015876 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31438 bytes_read=98827 bytes_retransmit=0 bytes_invalid=0 send_seq=5211 receive_seq=5211 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997254 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150569 bytes_read=4559222 bytes_retransmit=9 bytes_invalid=0 send_seq=20628 receive_seq=20628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997608 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91827 bytes_read=2073966 bytes_retransmit=9 bytes_invalid=0 send_seq=12331 receive_seq=12331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997466 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31705 bytes_read=1289014 bytes_retransmit=9 bytes_invalid=0 send_seq=5225 receive_seq=5225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32191 bytes_read=96905 bytes_retransmit=9 bytes_invalid=0 send_seq=5212 receive_seq=5212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86283 bytes_read=2026238 bytes_retransmit=0 bytes_invalid=0 send_seq=9771 receive_seq=9771 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998643 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=52.0 th1: temp=50.9 th2: temp=58.3 th3: temp=55.8 sysload=0.31 cputime=356.587 memavail=7392844 print_time=5077.866 buffer_time=2.151 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 25 Hz
Stats 5054.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22600684 bytes_read=3517285 bytes_retransmit=9 bytes_invalid=0 send_seq=424617 receive_seq=424617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015867 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31444 bytes_read=98843 bytes_retransmit=0 bytes_invalid=0 send_seq=5212 receive_seq=5212 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997264 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150645 bytes_read=4562278 bytes_retransmit=9 bytes_invalid=0 send_seq=20639 receive_seq=20639 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997777 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91833 bytes_read=2074066 bytes_retransmit=9 bytes_invalid=0 send_seq=12332 receive_seq=12332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997487 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31711 bytes_read=1289248 bytes_retransmit=9 bytes_invalid=0 send_seq=5226 receive_seq=5226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997629 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32197 bytes_read=96921 bytes_retransmit=9 bytes_invalid=0 send_seq=5213 receive_seq=5213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86289 bytes_read=2026594 bytes_retransmit=0 bytes_invalid=0 send_seq=9772 receive_seq=9772 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998652 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=52.2 th1: temp=50.7 th2: temp=58.2 th3: temp=55.9 sysload=0.31 cputime=356.658 memavail=7392844 print_time=5078.717 buffer_time=1.999 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 26 Hz
Stats 5055.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22602946 bytes_read=3517850 bytes_retransmit=9 bytes_invalid=0 send_seq=424668 receive_seq=424668 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015877 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31450 bytes_read=98859 bytes_retransmit=0 bytes_invalid=0 send_seq=5213 receive_seq=5213 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997270 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150721 bytes_read=4565392 bytes_retransmit=9 bytes_invalid=0 send_seq=20650 receive_seq=20650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997754 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91839 bytes_read=2074180 bytes_retransmit=9 bytes_invalid=0 send_seq=12333 receive_seq=12333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31717 bytes_read=1289482 bytes_retransmit=9 bytes_invalid=0 send_seq=5227 receive_seq=5227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32203 bytes_read=96936 bytes_retransmit=9 bytes_invalid=0 send_seq=5214 receive_seq=5214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86295 bytes_read=2026950 bytes_retransmit=0 bytes_invalid=0 send_seq=9773 receive_seq=9773 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998673 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=52.2 th1: temp=50.9 th2: temp=58.2 th3: temp=55.9 sysload=0.37 cputime=356.735 memavail=7392872 print_time=5079.952 buffer_time=2.232 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 27 Hz
Stats 5056.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22604886 bytes_read=3518420 bytes_retransmit=9 bytes_invalid=0 send_seq=424712 receive_seq=424712 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015863 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31456 bytes_read=98875 bytes_retransmit=0 bytes_invalid=0 send_seq=5214 receive_seq=5214 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997253 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150797 bytes_read=4568477 bytes_retransmit=9 bytes_invalid=0 send_seq=20661 receive_seq=20661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997679 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91845 bytes_read=2074308 bytes_retransmit=9 bytes_invalid=0 send_seq=12334 receive_seq=12334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997481 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31723 bytes_read=1289776 bytes_retransmit=9 bytes_invalid=0 send_seq=5228 receive_seq=5228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32209 bytes_read=96951 bytes_retransmit=9 bytes_invalid=0 send_seq=5215 receive_seq=5215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86301 bytes_read=2027306 bytes_retransmit=0 bytes_invalid=0 send_seq=9774 receive_seq=9774 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998657 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=52.3 th1: temp=51.1 th2: temp=58.3 th3: temp=56.0 sysload=0.37 cputime=356.807 memavail=7392872 print_time=5080.927 buffer_time=2.207 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 28 Hz
Stats 5057.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22606586 bytes_read=3518947 bytes_retransmit=9 bytes_invalid=0 send_seq=424756 receive_seq=424756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015868 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31462 bytes_read=98904 bytes_retransmit=0 bytes_invalid=0 send_seq=5215 receive_seq=5215 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997282 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150873 bytes_read=4571535 bytes_retransmit=9 bytes_invalid=0 send_seq=20672 receive_seq=20672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997694 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91851 bytes_read=2074408 bytes_retransmit=9 bytes_invalid=0 send_seq=12335 receive_seq=12335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997508 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31729 bytes_read=1290010 bytes_retransmit=9 bytes_invalid=0 send_seq=5229 receive_seq=5229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32215 bytes_read=96977 bytes_retransmit=9 bytes_invalid=0 send_seq=5216 receive_seq=5216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86307 bytes_read=2027661 bytes_retransmit=0 bytes_invalid=0 send_seq=9775 receive_seq=9775 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998667 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=52.4 th1: temp=51.0 th2: temp=58.3 th3: temp=56.0 sysload=0.37 cputime=356.882 memavail=7392876 print_time=5081.792 buffer_time=2.071 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 29 Hz
Testing frequency 30 Hz
Stats 5058.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22608509 bytes_read=3519497 bytes_retransmit=9 bytes_invalid=0 send_seq=424804 receive_seq=424804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015867 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31468 bytes_read=98920 bytes_retransmit=0 bytes_invalid=0 send_seq=5216 receive_seq=5216 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997262 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=150949 bytes_read=4574608 bytes_retransmit=9 bytes_invalid=0 send_seq=20683 receive_seq=20683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997653 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91857 bytes_read=2074508 bytes_retransmit=9 bytes_invalid=0 send_seq=12336 receive_seq=12336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997497 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31735 bytes_read=1290259 bytes_retransmit=9 bytes_invalid=0 send_seq=5230 receive_seq=5230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32221 bytes_read=96992 bytes_retransmit=9 bytes_invalid=0 send_seq=5217 receive_seq=5217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86313 bytes_read=2028006 bytes_retransmit=0 bytes_invalid=0 send_seq=9776 receive_seq=9776 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998660 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=52.4 th1: temp=51.2 th2: temp=58.3 th3: temp=56.0 sysload=0.37 cputime=356.961 memavail=7392876 print_time=5082.715 buffer_time=1.994 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5059.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22611026 bytes_read=3520126 bytes_retransmit=9 bytes_invalid=0 send_seq=424862 receive_seq=424862 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015858 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31474 bytes_read=98936 bytes_retransmit=0 bytes_invalid=0 send_seq=5217 receive_seq=5217 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997254 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=151025 bytes_read=4577692 bytes_retransmit=9 bytes_invalid=0 send_seq=20694 receive_seq=20694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997643 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91863 bytes_read=2074636 bytes_retransmit=9 bytes_invalid=0 send_seq=12337 receive_seq=12337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31741 bytes_read=1290553 bytes_retransmit=9 bytes_invalid=0 send_seq=5231 receive_seq=5231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32227 bytes_read=97007 bytes_retransmit=9 bytes_invalid=0 send_seq=5218 receive_seq=5218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86319 bytes_read=2028351 bytes_retransmit=0 bytes_invalid=0 send_seq=9777 receive_seq=9777 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998661 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=52.4 th1: temp=51.2 th2: temp=58.4 th3: temp=56.0 sysload=0.37 cputime=357.040 memavail=7392876 print_time=5083.944 buffer_time=2.222 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 31 Hz
Stats 5060.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22612783 bytes_read=3520666 bytes_retransmit=9 bytes_invalid=0 send_seq=424908 receive_seq=424908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015863 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31480 bytes_read=98952 bytes_retransmit=0 bytes_invalid=0 send_seq=5218 receive_seq=5218 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997265 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=151101 bytes_read=4580750 bytes_retransmit=9 bytes_invalid=0 send_seq=20705 receive_seq=20705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997687 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91869 bytes_read=2074736 bytes_retransmit=9 bytes_invalid=0 send_seq=12338 receive_seq=12338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31747 bytes_read=1290787 bytes_retransmit=9 bytes_invalid=0 send_seq=5232 receive_seq=5232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32233 bytes_read=97022 bytes_retransmit=9 bytes_invalid=0 send_seq=5219 receive_seq=5219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86325 bytes_read=2028694 bytes_retransmit=0 bytes_invalid=0 send_seq=9778 receive_seq=9778 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998670 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=52.6 th1: temp=51.3 th2: temp=58.4 th3: temp=56.1 sysload=0.34 cputime=357.116 memavail=7392876 print_time=5084.813 buffer_time=2.091 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 32 Hz
Stats 5061.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22614888 bytes_read=3521246 bytes_retransmit=9 bytes_invalid=0 send_seq=424959 receive_seq=424959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015930 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31486 bytes_read=98968 bytes_retransmit=0 bytes_invalid=0 send_seq=5219 receive_seq=5219 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997267 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=151177 bytes_read=4583810 bytes_retransmit=9 bytes_invalid=0 send_seq=20716 receive_seq=20716 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997655 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91875 bytes_read=2074850 bytes_retransmit=9 bytes_invalid=0 send_seq=12339 receive_seq=12339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997529 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31753 bytes_read=1291021 bytes_retransmit=9 bytes_invalid=0 send_seq=5233 receive_seq=5233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32239 bytes_read=97037 bytes_retransmit=9 bytes_invalid=0 send_seq=5220 receive_seq=5220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86331 bytes_read=2029039 bytes_retransmit=0 bytes_invalid=0 send_seq=9779 receive_seq=9779 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998673 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=52.7 th1: temp=51.3 th2: temp=58.5 th3: temp=56.1 sysload=0.34 cputime=357.193 memavail=7392876 print_time=5085.735 buffer_time=2.013 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 33 Hz
Stats 5062.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22617495 bytes_read=3521875 bytes_retransmit=9 bytes_invalid=0 send_seq=425017 receive_seq=425017 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015922 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31492 bytes_read=98997 bytes_retransmit=0 bytes_invalid=0 send_seq=5220 receive_seq=5220 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997166 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=151253 bytes_read=4586953 bytes_retransmit=9 bytes_invalid=0 send_seq=20727 receive_seq=20727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997505 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91881 bytes_read=2074978 bytes_retransmit=9 bytes_invalid=0 send_seq=12340 receive_seq=12340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997394 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31759 bytes_read=1291315 bytes_retransmit=9 bytes_invalid=0 send_seq=5234 receive_seq=5234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997544 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32245 bytes_read=97063 bytes_retransmit=9 bytes_invalid=0 send_seq=5221 receive_seq=5221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999408 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86337 bytes_read=2029384 bytes_retransmit=0 bytes_invalid=0 send_seq=9780 receive_seq=9780 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998602 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=52.4 th1: temp=51.3 th2: temp=58.5 th3: temp=56.0 sysload=0.34 cputime=357.276 memavail=7392892 print_time=5086.965 buffer_time=2.242 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 34 Hz
Stats 5063.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22619337 bytes_read=3522436 bytes_retransmit=9 bytes_invalid=0 send_seq=425065 receive_seq=425065 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015896 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31504 bytes_read=99029 bytes_retransmit=0 bytes_invalid=0 send_seq=5222 receive_seq=5222 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997220 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151335 bytes_read=4590044 bytes_retransmit=9 bytes_invalid=0 send_seq=20739 receive_seq=20739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997551 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91893 bytes_read=2075094 bytes_retransmit=9 bytes_invalid=0 send_seq=12342 receive_seq=12342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997438 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31771 bytes_read=1291580 bytes_retransmit=9 bytes_invalid=0 send_seq=5236 receive_seq=5236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997583 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32257 bytes_read=97093 bytes_retransmit=9 bytes_invalid=0 send_seq=5223 receive_seq=5223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999419 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86349 bytes_read=2029744 bytes_retransmit=0 bytes_invalid=0 send_seq=9782 receive_seq=9782 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998621 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=52.6 th1: temp=51.4 th2: temp=58.6 th3: temp=56.2 sysload=0.34 cputime=357.353 memavail=7392892 print_time=5087.859 buffer_time=2.136 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 35 Hz
Stats 5064.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22621656 bytes_read=3523016 bytes_retransmit=9 bytes_invalid=0 send_seq=425119 receive_seq=425119 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015887 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31510 bytes_read=99045 bytes_retransmit=0 bytes_invalid=0 send_seq=5223 receive_seq=5223 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997266 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151411 bytes_read=4593101 bytes_retransmit=9 bytes_invalid=0 send_seq=20750 receive_seq=20750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997593 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91899 bytes_read=2075194 bytes_retransmit=9 bytes_invalid=0 send_seq=12343 receive_seq=12343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997488 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31777 bytes_read=1291814 bytes_retransmit=9 bytes_invalid=0 send_seq=5237 receive_seq=5237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32263 bytes_read=97108 bytes_retransmit=9 bytes_invalid=0 send_seq=5224 receive_seq=5224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86355 bytes_read=2030089 bytes_retransmit=0 bytes_invalid=0 send_seq=9783 receive_seq=9783 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998639 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=52.7 th1: temp=51.7 th2: temp=58.7 th3: temp=56.2 sysload=0.34 cputime=357.436 memavail=7387404 print_time=5088.794 buffer_time=2.070 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 36 Hz
Stats 5065.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22624357 bytes_read=3523655 bytes_retransmit=9 bytes_invalid=0 send_seq=425179 receive_seq=425179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015885 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31516 bytes_read=99061 bytes_retransmit=0 bytes_invalid=0 send_seq=5224 receive_seq=5224 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997271 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151487 bytes_read=4596185 bytes_retransmit=9 bytes_invalid=0 send_seq=20761 receive_seq=20761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997605 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91905 bytes_read=2075322 bytes_retransmit=9 bytes_invalid=0 send_seq=12344 receive_seq=12344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31783 bytes_read=1292108 bytes_retransmit=9 bytes_invalid=0 send_seq=5238 receive_seq=5238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32269 bytes_read=97123 bytes_retransmit=9 bytes_invalid=0 send_seq=5225 receive_seq=5225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86361 bytes_read=2030434 bytes_retransmit=0 bytes_invalid=0 send_seq=9784 receive_seq=9784 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998655 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=52.4 th1: temp=51.4 th2: temp=58.5 th3: temp=56.3 sysload=0.47 cputime=357.522 memavail=7393772 print_time=5090.003 buffer_time=2.278 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 37 Hz
Stats 5066.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22626225 bytes_read=3524215 bytes_retransmit=9 bytes_invalid=0 send_seq=425226 receive_seq=425226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015890 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31522 bytes_read=99077 bytes_retransmit=0 bytes_invalid=0 send_seq=5225 receive_seq=5225 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997259 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151563 bytes_read=4599243 bytes_retransmit=9 bytes_invalid=0 send_seq=20772 receive_seq=20772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997612 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91911 bytes_read=2075436 bytes_retransmit=9 bytes_invalid=0 send_seq=12345 receive_seq=12345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997512 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31789 bytes_read=1292342 bytes_retransmit=9 bytes_invalid=0 send_seq=5239 receive_seq=5239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32275 bytes_read=97138 bytes_retransmit=9 bytes_invalid=0 send_seq=5226 receive_seq=5226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86367 bytes_read=2030787 bytes_retransmit=0 bytes_invalid=0 send_seq=9785 receive_seq=9785 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998657 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=52.8 th1: temp=51.4 th2: temp=58.8 th3: temp=56.3 sysload=0.47 cputime=357.601 memavail=7393772 print_time=5090.858 buffer_time=2.133 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 38 Hz
Stats 5067.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22628654 bytes_read=3524805 bytes_retransmit=9 bytes_invalid=0 send_seq=425283 receive_seq=425283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015887 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31528 bytes_read=99106 bytes_retransmit=0 bytes_invalid=0 send_seq=5226 receive_seq=5226 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997256 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151639 bytes_read=4602299 bytes_retransmit=9 bytes_invalid=0 send_seq=20783 receive_seq=20783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997591 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91917 bytes_read=2075536 bytes_retransmit=9 bytes_invalid=0 send_seq=12346 receive_seq=12346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31795 bytes_read=1292576 bytes_retransmit=9 bytes_invalid=0 send_seq=5240 receive_seq=5240 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32281 bytes_read=97164 bytes_retransmit=9 bytes_invalid=0 send_seq=5227 receive_seq=5227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86373 bytes_read=2031143 bytes_retransmit=0 bytes_invalid=0 send_seq=9786 receive_seq=9786 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998646 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=52.8 th1: temp=51.1 th2: temp=58.7 th3: temp=56.3 sysload=0.47 cputime=357.682 memavail=7393316 print_time=5091.804 buffer_time=2.079 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 39 Hz
Testing frequency 40 Hz
Stats 5068.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22631391 bytes_read=3525449 bytes_retransmit=9 bytes_invalid=0 send_seq=425344 receive_seq=425344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015878 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31534 bytes_read=99122 bytes_retransmit=0 bytes_invalid=0 send_seq=5227 receive_seq=5227 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997250 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151708 bytes_read=4605378 bytes_retransmit=9 bytes_invalid=0 send_seq=20793 receive_seq=20793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997600 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91923 bytes_read=2075664 bytes_retransmit=9 bytes_invalid=0 send_seq=12347 receive_seq=12347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=31801 bytes_read=1292885 bytes_retransmit=9 bytes_invalid=0 send_seq=5241 receive_seq=5241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997737 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32287 bytes_read=97179 bytes_retransmit=9 bytes_invalid=0 send_seq=5228 receive_seq=5228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86379 bytes_read=2031499 bytes_retransmit=0 bytes_invalid=0 send_seq=9787 receive_seq=9787 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998645 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=52.8 th1: temp=51.6 th2: temp=58.7 th3: temp=56.4 sysload=0.47 cputime=357.771 memavail=7393316 print_time=5093.029 buffer_time=2.302 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5069.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22633401 bytes_read=3525999 bytes_retransmit=9 bytes_invalid=0 send_seq=425392 receive_seq=425392 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015894 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31540 bytes_read=99138 bytes_retransmit=0 bytes_invalid=0 send_seq=5228 receive_seq=5228 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997261 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151784 bytes_read=4608492 bytes_retransmit=9 bytes_invalid=0 send_seq=20804 receive_seq=20804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997643 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91929 bytes_read=2075764 bytes_retransmit=9 bytes_invalid=0 send_seq=12348 receive_seq=12348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997543 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=31807 bytes_read=1293119 bytes_retransmit=9 bytes_invalid=0 send_seq=5242 receive_seq=5242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997726 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32293 bytes_read=97194 bytes_retransmit=9 bytes_invalid=0 send_seq=5229 receive_seq=5229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86385 bytes_read=2031855 bytes_retransmit=0 bytes_invalid=0 send_seq=9788 receive_seq=9788 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998666 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=53.1 th1: temp=51.4 th2: temp=58.9 th3: temp=56.3 sysload=0.47 cputime=357.851 memavail=7393316 print_time=5093.906 buffer_time=2.179 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 41 Hz
Stats 5070.1: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22635947 bytes_read=3526604 bytes_retransmit=9 bytes_invalid=0 send_seq=425451 receive_seq=425451 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015887 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31546 bytes_read=99154 bytes_retransmit=0 bytes_invalid=0 send_seq=5229 receive_seq=5229 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997235 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151860 bytes_read=4611548 bytes_retransmit=9 bytes_invalid=0 send_seq=20815 receive_seq=20815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997599 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91935 bytes_read=2075864 bytes_retransmit=9 bytes_invalid=0 send_seq=12349 receive_seq=12349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=31813 bytes_read=1293353 bytes_retransmit=9 bytes_invalid=0 send_seq=5243 receive_seq=5243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997683 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32299 bytes_read=97209 bytes_retransmit=9 bytes_invalid=0 send_seq=5230 receive_seq=5230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999444 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86391 bytes_read=2032211 bytes_retransmit=0 bytes_invalid=0 send_seq=9789 receive_seq=9789 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998653 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=52.8 th1: temp=51.7 th2: temp=58.6 th3: temp=56.4 sysload=0.52 cputime=357.933 memavail=7393316 print_time=5094.831 buffer_time=2.104 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 42 Hz
Testing frequency 43 Hz
Stats 5071.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22638743 bytes_read=3527203 bytes_retransmit=9 bytes_invalid=0 send_seq=425512 receive_seq=425500 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=158 upcoming_bytes=0 freq=400015911 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31552 bytes_read=99170 bytes_retransmit=0 bytes_invalid=0 send_seq=5230 receive_seq=5230 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997249 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151936 bytes_read=4614634 bytes_retransmit=9 bytes_invalid=0 send_seq=20826 receive_seq=20826 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997610 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91941 bytes_read=2076006 bytes_retransmit=9 bytes_invalid=0 send_seq=12350 receive_seq=12350 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997516 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=31819 bytes_read=1293647 bytes_retransmit=9 bytes_invalid=0 send_seq=5244 receive_seq=5244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997693 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32305 bytes_read=97224 bytes_retransmit=9 bytes_invalid=0 send_seq=5231 receive_seq=5231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999444 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86397 bytes_read=2032567 bytes_retransmit=0 bytes_invalid=0 send_seq=9790 receive_seq=9790 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998654 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=52.9 th1: temp=51.8 th2: temp=58.9 th3: temp=56.4 sysload=0.52 cputime=358.022 memavail=7393324 print_time=5096.034 buffer_time=2.304 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5072.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22640931 bytes_read=3527818 bytes_retransmit=9 bytes_invalid=0 send_seq=425561 receive_seq=425561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015897 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=31558 bytes_read=99199 bytes_retransmit=0 bytes_invalid=0 send_seq=5231 receive_seq=5231 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997233 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152012 bytes_read=4617692 bytes_retransmit=9 bytes_invalid=0 send_seq=20837 receive_seq=20837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997687 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91947 bytes_read=2076106 bytes_retransmit=9 bytes_invalid=0 send_seq=12351 receive_seq=12351 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997478 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=31825 bytes_read=1293881 bytes_retransmit=9 bytes_invalid=0 send_seq=5245 receive_seq=5245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32311 bytes_read=97250 bytes_retransmit=9 bytes_invalid=0 send_seq=5232 receive_seq=5232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999434 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86403 bytes_read=2032923 bytes_retransmit=0 bytes_invalid=0 send_seq=9791 receive_seq=9791 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998633 coil_temp=16.9 refs=0 mcu_temp=20.18 supply_voltage=3.011 th0: temp=52.9 th1: temp=51.7 th2: temp=58.8 th3: temp=56.5 sysload=0.52 cputime=358.103 memavail=7393324 print_time=5096.936 buffer_time=2.207 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 44 Hz
Stats 5073.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22643546 bytes_read=3528418 bytes_retransmit=9 bytes_invalid=0 send_seq=425619 receive_seq=425619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015908 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=31564 bytes_read=99215 bytes_retransmit=0 bytes_invalid=0 send_seq=5232 receive_seq=5232 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997253 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152088 bytes_read=4620767 bytes_retransmit=9 bytes_invalid=0 send_seq=20848 receive_seq=20848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997790 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91953 bytes_read=2076206 bytes_retransmit=9 bytes_invalid=0 send_seq=12352 receive_seq=12352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997535 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31831 bytes_read=1294130 bytes_retransmit=9 bytes_invalid=0 send_seq=5246 receive_seq=5246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32317 bytes_read=97265 bytes_retransmit=9 bytes_invalid=0 send_seq=5233 receive_seq=5233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86409 bytes_read=2033279 bytes_retransmit=0 bytes_invalid=0 send_seq=9792 receive_seq=9792 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998649 coil_temp=16.9 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=52.9 th1: temp=51.7 th2: temp=58.8 th3: temp=56.5 sysload=0.52 cputime=358.183 memavail=7393324 print_time=5097.843 buffer_time=2.112 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 45 Hz
Stats 5074.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22645639 bytes_read=3529012 bytes_retransmit=9 bytes_invalid=0 send_seq=425670 receive_seq=425670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015901 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=31570 bytes_read=99231 bytes_retransmit=0 bytes_invalid=0 send_seq=5233 receive_seq=5233 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997246 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152164 bytes_read=4623851 bytes_retransmit=9 bytes_invalid=0 send_seq=20859 receive_seq=20859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997771 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91959 bytes_read=2076334 bytes_retransmit=9 bytes_invalid=0 send_seq=12353 receive_seq=12353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997560 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31837 bytes_read=1294424 bytes_retransmit=9 bytes_invalid=0 send_seq=5247 receive_seq=5247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32323 bytes_read=97280 bytes_retransmit=9 bytes_invalid=0 send_seq=5234 receive_seq=5234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86415 bytes_read=2033635 bytes_retransmit=0 bytes_invalid=0 send_seq=9793 receive_seq=9793 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998638 coil_temp=16.9 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=52.8 th1: temp=51.9 th2: temp=58.9 th3: temp=56.5 sysload=0.52 cputime=358.268 memavail=7393324 print_time=5098.738 buffer_time=2.007 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 46 Hz
Stats 5075.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22648628 bytes_read=3529647 bytes_retransmit=9 bytes_invalid=0 send_seq=425735 receive_seq=425735 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015888 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=31576 bytes_read=99247 bytes_retransmit=0 bytes_invalid=0 send_seq=5234 receive_seq=5234 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997266 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152240 bytes_read=4626907 bytes_retransmit=9 bytes_invalid=0 send_seq=20870 receive_seq=20870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997744 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=91965 bytes_read=2076434 bytes_retransmit=9 bytes_invalid=0 send_seq=12354 receive_seq=12354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997558 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31843 bytes_read=1294658 bytes_retransmit=9 bytes_invalid=0 send_seq=5248 receive_seq=5248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32329 bytes_read=97295 bytes_retransmit=9 bytes_invalid=0 send_seq=5235 receive_seq=5235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86421 bytes_read=2033975 bytes_retransmit=0 bytes_invalid=0 send_seq=9794 receive_seq=9794 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998652 coil_temp=16.9 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=53.1 th1: temp=51.7 th2: temp=58.8 th3: temp=56.5 sysload=0.56 cputime=358.356 memavail=7393324 print_time=5099.941 buffer_time=2.210 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 47 Hz
Stats 5076.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22651285 bytes_read=3530272 bytes_retransmit=9 bytes_invalid=0 send_seq=425795 receive_seq=425795 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015879 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=31582 bytes_read=99262 bytes_retransmit=0 bytes_invalid=0 send_seq=5235 receive_seq=5235 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997291 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152316 bytes_read=4630021 bytes_retransmit=9 bytes_invalid=0 send_seq=20881 receive_seq=20881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997720 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=91971 bytes_read=2076548 bytes_retransmit=9 bytes_invalid=0 send_seq=12355 receive_seq=12355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997557 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31849 bytes_read=1294888 bytes_retransmit=9 bytes_invalid=0 send_seq=5249 receive_seq=5249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32335 bytes_read=97310 bytes_retransmit=9 bytes_invalid=0 send_seq=5236 receive_seq=5236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86427 bytes_read=2034331 bytes_retransmit=0 bytes_invalid=0 send_seq=9795 receive_seq=9795 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998677 coil_temp=16.9 refs=0 mcu_temp=20.18 supply_voltage=3.011 th0: temp=53.1 th1: temp=51.9 th2: temp=58.8 th3: temp=56.4 sysload=0.56 cputime=358.436 memavail=7393324 print_time=5100.870 buffer_time=2.138 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 48 Hz
Stats 5077.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22653417 bytes_read=3530866 bytes_retransmit=9 bytes_invalid=0 send_seq=425846 receive_seq=425846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015887 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=31588 bytes_read=99277 bytes_retransmit=0 bytes_invalid=0 send_seq=5236 receive_seq=5236 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997295 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152392 bytes_read=4633092 bytes_retransmit=9 bytes_invalid=0 send_seq=20892 receive_seq=20892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997706 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=91977 bytes_read=2076667 bytes_retransmit=9 bytes_invalid=0 send_seq=12356 receive_seq=12356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997557 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=31855 bytes_read=1295162 bytes_retransmit=9 bytes_invalid=0 send_seq=5250 receive_seq=5250 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997694 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32341 bytes_read=97337 bytes_retransmit=9 bytes_invalid=0 send_seq=5237 receive_seq=5237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86433 bytes_read=2034687 bytes_retransmit=0 bytes_invalid=0 send_seq=9796 receive_seq=9796 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998695 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=53.0 th1: temp=51.9 th2: temp=58.8 th3: temp=56.5 sysload=0.56 cputime=358.520 memavail=7392324 print_time=5101.755 buffer_time=2.023 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 49 Hz
Stats 5078.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22656586 bytes_read=3531511 bytes_retransmit=9 bytes_invalid=0 send_seq=425914 receive_seq=425914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015893 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31594 bytes_read=99305 bytes_retransmit=0 bytes_invalid=0 send_seq=5237 receive_seq=5237 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997268 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152468 bytes_read=4636148 bytes_retransmit=9 bytes_invalid=0 send_seq=20903 receive_seq=20903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997660 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=91983 bytes_read=2076760 bytes_retransmit=9 bytes_invalid=0 send_seq=12357 receive_seq=12357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31861 bytes_read=1295395 bytes_retransmit=9 bytes_invalid=0 send_seq=5251 receive_seq=5251 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32347 bytes_read=97353 bytes_retransmit=9 bytes_invalid=0 send_seq=5238 receive_seq=5238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86439 bytes_read=2035043 bytes_retransmit=0 bytes_invalid=0 send_seq=9797 receive_seq=9797 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998681 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=53.2 th1: temp=51.7 th2: temp=58.9 th3: temp=56.6 sysload=0.56 cputime=358.608 memavail=7392324 print_time=5102.971 buffer_time=2.238 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 50 Hz
Stats 5079.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22659329 bytes_read=3532131 bytes_retransmit=9 bytes_invalid=0 send_seq=425976 receive_seq=425976 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015884 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31600 bytes_read=99320 bytes_retransmit=0 bytes_invalid=0 send_seq=5238 receive_seq=5238 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997252 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152544 bytes_read=4639188 bytes_retransmit=9 bytes_invalid=0 send_seq=20914 receive_seq=20914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997630 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=91989 bytes_read=2076853 bytes_retransmit=9 bytes_invalid=0 send_seq=12358 receive_seq=12358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31867 bytes_read=1295613 bytes_retransmit=9 bytes_invalid=0 send_seq=5252 receive_seq=5252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32353 bytes_read=97369 bytes_retransmit=9 bytes_invalid=0 send_seq=5239 receive_seq=5239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86445 bytes_read=2035399 bytes_retransmit=0 bytes_invalid=0 send_seq=9798 receive_seq=9798 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998677 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=53.2 th1: temp=51.9 th2: temp=59.0 th3: temp=56.6 sysload=0.56 cputime=358.689 memavail=7392360 print_time=5103.878 buffer_time=2.145 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 51 Hz
Stats 5080.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22661483 bytes_read=3532730 bytes_retransmit=9 bytes_invalid=0 send_seq=426028 receive_seq=426028 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015878 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31606 bytes_read=99335 bytes_retransmit=0 bytes_invalid=0 send_seq=5239 receive_seq=5239 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997287 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152620 bytes_read=4642253 bytes_retransmit=9 bytes_invalid=0 send_seq=20925 receive_seq=20925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997649 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=91995 bytes_read=2076972 bytes_retransmit=9 bytes_invalid=0 send_seq=12359 receive_seq=12359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997513 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31873 bytes_read=1295887 bytes_retransmit=9 bytes_invalid=0 send_seq=5253 receive_seq=5253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32359 bytes_read=97385 bytes_retransmit=9 bytes_invalid=0 send_seq=5240 receive_seq=5240 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86451 bytes_read=2035755 bytes_retransmit=0 bytes_invalid=0 send_seq=9799 receive_seq=9799 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998694 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=53.0 th1: temp=51.9 th2: temp=59.0 th3: temp=56.5 sysload=0.51 cputime=358.773 memavail=7392360 print_time=5104.770 buffer_time=2.037 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 52 Hz
Stats 5081.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22664706 bytes_read=3533405 bytes_retransmit=9 bytes_invalid=0 send_seq=426098 receive_seq=426098 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=0 freq=400015887 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31612 bytes_read=99350 bytes_retransmit=0 bytes_invalid=0 send_seq=5240 receive_seq=5240 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997313 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152696 bytes_read=4645307 bytes_retransmit=9 bytes_invalid=0 send_seq=20936 receive_seq=20936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997642 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92001 bytes_read=2077086 bytes_retransmit=9 bytes_invalid=0 send_seq=12360 receive_seq=12360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31879 bytes_read=1296105 bytes_retransmit=9 bytes_invalid=0 send_seq=5254 receive_seq=5254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32365 bytes_read=97401 bytes_retransmit=9 bytes_invalid=0 send_seq=5241 receive_seq=5241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999458 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86457 bytes_read=2036111 bytes_retransmit=0 bytes_invalid=0 send_seq=9800 receive_seq=9800 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998697 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=53.0 th1: temp=52.0 th2: temp=59.0 th3: temp=56.6 sysload=0.51 cputime=358.878 memavail=7390204 print_time=5105.978 buffer_time=2.244 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 53 Hz
Stats 5082.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22667550 bytes_read=3534025 bytes_retransmit=9 bytes_invalid=0 send_seq=426160 receive_seq=426160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015887 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31618 bytes_read=99366 bytes_retransmit=0 bytes_invalid=0 send_seq=5241 receive_seq=5241 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997300 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152772 bytes_read=4648365 bytes_retransmit=9 bytes_invalid=0 send_seq=20947 receive_seq=20947 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997636 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92007 bytes_read=2077186 bytes_retransmit=9 bytes_invalid=0 send_seq=12361 receive_seq=12361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31885 bytes_read=1296332 bytes_retransmit=9 bytes_invalid=0 send_seq=5255 receive_seq=5255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32371 bytes_read=97428 bytes_retransmit=9 bytes_invalid=0 send_seq=5242 receive_seq=5242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86463 bytes_read=2036467 bytes_retransmit=0 bytes_invalid=0 send_seq=9801 receive_seq=9801 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998682 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=53.1 th1: temp=52.0 th2: temp=59.1 th3: temp=56.7 sysload=0.51 cputime=358.965 memavail=7395604 print_time=5106.890 buffer_time=2.156 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 54 Hz
Stats 5083.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22669770 bytes_read=3534624 bytes_retransmit=9 bytes_invalid=0 send_seq=426212 receive_seq=426212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015888 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31624 bytes_read=99395 bytes_retransmit=0 bytes_invalid=0 send_seq=5242 receive_seq=5242 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997305 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152841 bytes_read=4651445 bytes_retransmit=9 bytes_invalid=0 send_seq=20957 receive_seq=20957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997681 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92013 bytes_read=2077314 bytes_retransmit=9 bytes_invalid=0 send_seq=12362 receive_seq=12362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997589 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31891 bytes_read=1296641 bytes_retransmit=9 bytes_invalid=0 send_seq=5256 receive_seq=5256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32377 bytes_read=97444 bytes_retransmit=9 bytes_invalid=0 send_seq=5243 receive_seq=5243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86469 bytes_read=2036823 bytes_retransmit=0 bytes_invalid=0 send_seq=9802 receive_seq=9802 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998672 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=53.2 th1: temp=52.0 th2: temp=58.9 th3: temp=56.9 sysload=0.51 cputime=359.049 memavail=7395604 print_time=5107.788 buffer_time=2.053 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 55 Hz
Stats 5084.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22673086 bytes_read=3535289 bytes_retransmit=9 bytes_invalid=0 send_seq=426283 receive_seq=426283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015876 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31630 bytes_read=99411 bytes_retransmit=0 bytes_invalid=0 send_seq=5243 receive_seq=5243 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997296 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152917 bytes_read=4654561 bytes_retransmit=9 bytes_invalid=0 send_seq=20968 receive_seq=20968 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997659 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92019 bytes_read=2077414 bytes_retransmit=9 bytes_invalid=0 send_seq=12363 receive_seq=12363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997680 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31897 bytes_read=1296875 bytes_retransmit=9 bytes_invalid=0 send_seq=5257 receive_seq=5257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32383 bytes_read=97460 bytes_retransmit=9 bytes_invalid=0 send_seq=5244 receive_seq=5244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86475 bytes_read=2037179 bytes_retransmit=0 bytes_invalid=0 send_seq=9803 receive_seq=9803 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998668 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=53.2 th1: temp=52.0 th2: temp=59.1 th3: temp=56.6 sysload=0.51 cputime=359.141 memavail=7395604 print_time=5109.006 buffer_time=2.271 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 56 Hz
Stats 5085.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22675949 bytes_read=3535914 bytes_retransmit=9 bytes_invalid=0 send_seq=426346 receive_seq=426346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015866 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31636 bytes_read=99427 bytes_retransmit=0 bytes_invalid=0 send_seq=5244 receive_seq=5244 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997293 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152993 bytes_read=4657618 bytes_retransmit=9 bytes_invalid=0 send_seq=20979 receive_seq=20979 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997663 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92025 bytes_read=2077514 bytes_retransmit=9 bytes_invalid=0 send_seq=12364 receive_seq=12364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997634 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31903 bytes_read=1297109 bytes_retransmit=9 bytes_invalid=0 send_seq=5258 receive_seq=5258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32389 bytes_read=97476 bytes_retransmit=9 bytes_invalid=0 send_seq=5245 receive_seq=5245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86481 bytes_read=2037535 bytes_retransmit=0 bytes_invalid=0 send_seq=9804 receive_seq=9804 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998671 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=53.1 th1: temp=52.0 th2: temp=59.1 th3: temp=56.6 sysload=0.47 cputime=359.225 memavail=7395604 print_time=5109.884 buffer_time=2.148 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 57 Hz
Stats 5086.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22678308 bytes_read=3536543 bytes_retransmit=9 bytes_invalid=0 send_seq=426401 receive_seq=426401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015875 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31642 bytes_read=99443 bytes_retransmit=0 bytes_invalid=0 send_seq=5245 receive_seq=5245 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997312 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153069 bytes_read=4660705 bytes_retransmit=9 bytes_invalid=0 send_seq=20990 receive_seq=20990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997666 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92031 bytes_read=2077656 bytes_retransmit=9 bytes_invalid=0 send_seq=12365 receive_seq=12365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997628 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31909 bytes_read=1297403 bytes_retransmit=9 bytes_invalid=0 send_seq=5259 receive_seq=5259 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32395 bytes_read=97492 bytes_retransmit=9 bytes_invalid=0 send_seq=5246 receive_seq=5246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86487 bytes_read=2037891 bytes_retransmit=0 bytes_invalid=0 send_seq=9805 receive_seq=9805 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998680 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=53.2 th1: temp=52.1 th2: temp=59.1 th3: temp=56.7 sysload=0.47 cputime=359.312 memavail=7395604 print_time=5110.810 buffer_time=2.075 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 58 Hz
Testing frequency 59 Hz
Stats 5087.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22681692 bytes_read=3537213 bytes_retransmit=9 bytes_invalid=0 send_seq=426473 receive_seq=426473 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=0 freq=400015869 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31648 bytes_read=99459 bytes_retransmit=0 bytes_invalid=0 send_seq=5246 receive_seq=5246 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997295 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153145 bytes_read=4663762 bytes_retransmit=9 bytes_invalid=0 send_seq=21001 receive_seq=21001 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997642 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92037 bytes_read=2077756 bytes_retransmit=9 bytes_invalid=0 send_seq=12366 receive_seq=12366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997575 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31915 bytes_read=1297637 bytes_retransmit=9 bytes_invalid=0 send_seq=5260 receive_seq=5260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32401 bytes_read=97519 bytes_retransmit=9 bytes_invalid=0 send_seq=5247 receive_seq=5247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86493 bytes_read=2038247 bytes_retransmit=0 bytes_invalid=0 send_seq=9806 receive_seq=9806 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998660 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=53.1 th1: temp=52.0 th2: temp=59.1 th3: temp=56.7 sysload=0.47 cputime=359.405 memavail=7395140 print_time=5112.024 buffer_time=2.287 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5088.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22684625 bytes_read=3537833 bytes_retransmit=9 bytes_invalid=0 send_seq=426535 receive_seq=426535 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015891 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31654 bytes_read=99488 bytes_retransmit=0 bytes_invalid=0 send_seq=5247 receive_seq=5247 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997299 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153221 bytes_read=4666836 bytes_retransmit=9 bytes_invalid=0 send_seq=21012 receive_seq=21012 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997640 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92043 bytes_read=2077856 bytes_retransmit=9 bytes_invalid=0 send_seq=12367 receive_seq=12367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997565 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=31921 bytes_read=1297886 bytes_retransmit=9 bytes_invalid=0 send_seq=5261 receive_seq=5261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32407 bytes_read=97535 bytes_retransmit=9 bytes_invalid=0 send_seq=5248 receive_seq=5248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86499 bytes_read=2038603 bytes_retransmit=0 bytes_invalid=0 send_seq=9807 receive_seq=9807 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998658 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=53.1 th1: temp=52.2 th2: temp=59.0 th3: temp=56.7 sysload=0.47 cputime=359.486 memavail=7395140 print_time=5112.907 buffer_time=2.169 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 60 Hz
Stats 5089.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22687054 bytes_read=3538442 bytes_retransmit=9 bytes_invalid=0 send_seq=426590 receive_seq=426590 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015906 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31660 bytes_read=99504 bytes_retransmit=0 bytes_invalid=0 send_seq=5248 receive_seq=5248 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997263 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153297 bytes_read=4669921 bytes_retransmit=9 bytes_invalid=0 send_seq=21023 receive_seq=21023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997775 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92049 bytes_read=2077984 bytes_retransmit=9 bytes_invalid=0 send_seq=12368 receive_seq=12368 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=31927 bytes_read=1298180 bytes_retransmit=9 bytes_invalid=0 send_seq=5262 receive_seq=5262 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997606 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32413 bytes_read=97551 bytes_retransmit=9 bytes_invalid=0 send_seq=5249 receive_seq=5249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86505 bytes_read=2038959 bytes_retransmit=0 bytes_invalid=0 send_seq=9808 receive_seq=9808 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998635 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=53.2 th1: temp=52.1 th2: temp=59.0 th3: temp=56.8 sysload=0.47 cputime=359.573 memavail=7395140 print_time=5113.826 buffer_time=2.089 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 61 Hz
Testing frequency 62 Hz
Stats 5090.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22690562 bytes_read=3539127 bytes_retransmit=9 bytes_invalid=0 send_seq=426665 receive_seq=426665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=400015902 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31666 bytes_read=99520 bytes_retransmit=0 bytes_invalid=0 send_seq=5249 receive_seq=5249 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997249 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153373 bytes_read=4672977 bytes_retransmit=9 bytes_invalid=0 send_seq=21034 receive_seq=21034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997729 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92055 bytes_read=2078084 bytes_retransmit=9 bytes_invalid=0 send_seq=12369 receive_seq=12369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997460 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=31933 bytes_read=1298414 bytes_retransmit=9 bytes_invalid=0 send_seq=5263 receive_seq=5263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997582 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32419 bytes_read=97567 bytes_retransmit=9 bytes_invalid=0 send_seq=5250 receive_seq=5250 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999430 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86511 bytes_read=2039315 bytes_retransmit=0 bytes_invalid=0 send_seq=9809 receive_seq=9809 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998617 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=53.4 th1: temp=52.3 th2: temp=59.1 th3: temp=56.7 sysload=0.43 cputime=359.665 memavail=7395140 print_time=5115.031 buffer_time=2.293 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Stats 5091.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22693552 bytes_read=3539772 bytes_retransmit=9 bytes_invalid=0 send_seq=426729 receive_seq=426729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015895 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31672 bytes_read=99536 bytes_retransmit=0 bytes_invalid=0 send_seq=5250 receive_seq=5250 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997254 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153449 bytes_read=4676091 bytes_retransmit=9 bytes_invalid=0 send_seq=21045 receive_seq=21045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997848 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92061 bytes_read=2078198 bytes_retransmit=9 bytes_invalid=0 send_seq=12370 receive_seq=12370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997465 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=31939 bytes_read=1298648 bytes_retransmit=9 bytes_invalid=0 send_seq=5264 receive_seq=5264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997599 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32425 bytes_read=97583 bytes_retransmit=9 bytes_invalid=0 send_seq=5251 receive_seq=5251 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86517 bytes_read=2039671 bytes_retransmit=0 bytes_invalid=0 send_seq=9810 receive_seq=9810 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998629 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=53.0 th1: temp=52.1 th2: temp=59.0 th3: temp=56.7 sysload=0.43 cputime=359.755 memavail=7395140 print_time=5115.924 buffer_time=2.184 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 63 Hz
Stats 5092.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22696089 bytes_read=3540406 bytes_retransmit=9 bytes_invalid=0 send_seq=426788 receive_seq=426788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015894 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31678 bytes_read=99552 bytes_retransmit=0 bytes_invalid=0 send_seq=5251 receive_seq=5251 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997265 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153525 bytes_read=4679177 bytes_retransmit=9 bytes_invalid=0 send_seq=21056 receive_seq=21056 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997810 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92067 bytes_read=2078326 bytes_retransmit=9 bytes_invalid=0 send_seq=12371 receive_seq=12371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997469 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=31945 bytes_read=1298942 bytes_retransmit=9 bytes_invalid=0 send_seq=5265 receive_seq=5265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997608 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32431 bytes_read=97610 bytes_retransmit=9 bytes_invalid=0 send_seq=5252 receive_seq=5252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999434 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86523 bytes_read=2040027 bytes_retransmit=0 bytes_invalid=0 send_seq=9811 receive_seq=9811 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998639 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=53.1 th1: temp=52.0 th2: temp=59.1 th3: temp=56.7 sysload=0.43 cputime=359.923 memavail=7395156 print_time=5116.847 buffer_time=2.107 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 64 Hz
Testing frequency 65 Hz
Stats 5093.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22699637 bytes_read=3541091 bytes_retransmit=9 bytes_invalid=0 send_seq=426863 receive_seq=426863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=400015888 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31684 bytes_read=99581 bytes_retransmit=0 bytes_invalid=0 send_seq=5252 receive_seq=5252 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997268 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153594 bytes_read=4682227 bytes_retransmit=9 bytes_invalid=0 send_seq=21066 receive_seq=21066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997761 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92073 bytes_read=2078426 bytes_retransmit=9 bytes_invalid=0 send_seq=12372 receive_seq=12372 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997464 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31951 bytes_read=1299191 bytes_retransmit=9 bytes_invalid=0 send_seq=5266 receive_seq=5266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997615 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32437 bytes_read=97626 bytes_retransmit=9 bytes_invalid=0 send_seq=5253 receive_seq=5253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999434 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86529 bytes_read=2040383 bytes_retransmit=0 bytes_invalid=0 send_seq=9812 receive_seq=9812 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998641 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=53.2 th1: temp=52.2 th2: temp=59.2 th3: temp=56.8 sysload=0.43 cputime=360.023 memavail=7395156 print_time=5118.049 buffer_time=2.307 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5094.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22702638 bytes_read=3541726 bytes_retransmit=9 bytes_invalid=0 send_seq=426928 receive_seq=426928 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015879 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31690 bytes_read=99597 bytes_retransmit=0 bytes_invalid=0 send_seq=5253 receive_seq=5253 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997272 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153670 bytes_read=4685285 bytes_retransmit=9 bytes_invalid=0 send_seq=21077 receive_seq=21077 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997724 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92079 bytes_read=2078526 bytes_retransmit=9 bytes_invalid=0 send_seq=12373 receive_seq=12373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31957 bytes_read=1299425 bytes_retransmit=9 bytes_invalid=0 send_seq=5267 receive_seq=5267 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32443 bytes_read=97642 bytes_retransmit=9 bytes_invalid=0 send_seq=5254 receive_seq=5254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86535 bytes_read=2040739 bytes_retransmit=0 bytes_invalid=0 send_seq=9813 receive_seq=9813 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998648 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=53.1 th1: temp=52.2 th2: temp=59.1 th3: temp=56.7 sysload=0.43 cputime=360.110 memavail=7395156 print_time=5118.916 buffer_time=2.173 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 66 Hz
Stats 5095.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=22705323 bytes_read=3542370 bytes_retransmit=9 bytes_invalid=0 send_seq=426989 receive_seq=426989 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015889 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31696 bytes_read=99613 bytes_retransmit=0 bytes_invalid=0 send_seq=5254 receive_seq=5254 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997279 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153746 bytes_read=4688369 bytes_retransmit=9 bytes_invalid=0 send_seq=21088 receive_seq=21088 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997714 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92085 bytes_read=2078654 bytes_retransmit=9 bytes_invalid=0 send_seq=12374 receive_seq=12374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997497 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31963 bytes_read=1299719 bytes_retransmit=9 bytes_invalid=0 send_seq=5268 receive_seq=5268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32449 bytes_read=97658 bytes_retransmit=9 bytes_invalid=0 send_seq=5255 receive_seq=5255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86541 bytes_read=2041095 bytes_retransmit=0 bytes_invalid=0 send_seq=9814 receive_seq=9814 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998653 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=53.2 th1: temp=52.4 th2: temp=59.1 th3: temp=56.7 sysload=0.40 cputime=360.201 memavail=7394932 print_time=5119.861 buffer_time=2.117 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 67 Hz
Testing frequency 68 Hz
Stats 5096.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22708340 bytes_read=3543026 bytes_retransmit=9 bytes_invalid=0 send_seq=427055 receive_seq=427055 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015900 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31702 bytes_read=99629 bytes_retransmit=0 bytes_invalid=0 send_seq=5255 receive_seq=5255 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997247 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153822 bytes_read=4691427 bytes_retransmit=9 bytes_invalid=0 send_seq=21099 receive_seq=21099 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997709 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92091 bytes_read=2078768 bytes_retransmit=9 bytes_invalid=0 send_seq=12375 receive_seq=12375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997479 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31969 bytes_read=1299953 bytes_retransmit=9 bytes_invalid=0 send_seq=5269 receive_seq=5269 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32455 bytes_read=97674 bytes_retransmit=9 bytes_invalid=0 send_seq=5256 receive_seq=5256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86547 bytes_read=2041451 bytes_retransmit=0 bytes_invalid=0 send_seq=9815 receive_seq=9815 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998639 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=53.1 th1: temp=52.2 th2: temp=59.1 th3: temp=56.7 sysload=0.40 cputime=360.293 memavail=7394964 print_time=5120.742 buffer_time=1.995 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5097.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22712032 bytes_read=3543740 bytes_retransmit=9 bytes_invalid=0 send_seq=427133 receive_seq=427133 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015893 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31708 bytes_read=99645 bytes_retransmit=0 bytes_invalid=0 send_seq=5256 receive_seq=5256 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997234 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153898 bytes_read=4694542 bytes_retransmit=9 bytes_invalid=0 send_seq=21110 receive_seq=21110 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997657 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92097 bytes_read=2078868 bytes_retransmit=9 bytes_invalid=0 send_seq=12376 receive_seq=12376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997455 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=31975 bytes_read=1300187 bytes_retransmit=9 bytes_invalid=0 send_seq=5270 receive_seq=5270 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997617 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32461 bytes_read=97701 bytes_retransmit=9 bytes_invalid=0 send_seq=5257 receive_seq=5257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86553 bytes_read=2041807 bytes_retransmit=0 bytes_invalid=0 send_seq=9816 receive_seq=9816 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998632 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=53.3 th1: temp=52.4 th2: temp=59.2 th3: temp=56.9 sysload=0.40 cputime=360.385 memavail=7394964 print_time=5121.942 buffer_time=2.194 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 69 Hz
Stats 5098.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22714820 bytes_read=3544375 bytes_retransmit=9 bytes_invalid=0 send_seq=427195 receive_seq=427195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015886 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31714 bytes_read=99674 bytes_retransmit=0 bytes_invalid=0 send_seq=5257 receive_seq=5257 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997268 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153974 bytes_read=4697644 bytes_retransmit=9 bytes_invalid=0 send_seq=21121 receive_seq=21121 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997656 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92103 bytes_read=2078996 bytes_retransmit=9 bytes_invalid=0 send_seq=12377 receive_seq=12377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997477 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=31981 bytes_read=1300496 bytes_retransmit=9 bytes_invalid=0 send_seq=5271 receive_seq=5271 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32467 bytes_read=97717 bytes_retransmit=9 bytes_invalid=0 send_seq=5258 receive_seq=5258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86559 bytes_read=2042163 bytes_retransmit=0 bytes_invalid=0 send_seq=9817 receive_seq=9817 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998643 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=53.2 th1: temp=52.4 th2: temp=59.1 th3: temp=56.9 sysload=0.40 cputime=360.478 memavail=7394212 print_time=5122.868 buffer_time=2.120 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 70 Hz
Testing frequency 71 Hz
Stats 5099.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22717868 bytes_read=3545013 bytes_retransmit=9 bytes_invalid=0 send_seq=427261 receive_seq=427261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015906 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31720 bytes_read=99690 bytes_retransmit=0 bytes_invalid=0 send_seq=5258 receive_seq=5258 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997285 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154050 bytes_read=4700700 bytes_retransmit=9 bytes_invalid=0 send_seq=21132 receive_seq=21132 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997659 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92109 bytes_read=2079096 bytes_retransmit=9 bytes_invalid=0 send_seq=12378 receive_seq=12378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=31987 bytes_read=1300730 bytes_retransmit=9 bytes_invalid=0 send_seq=5272 receive_seq=5272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32473 bytes_read=97733 bytes_retransmit=9 bytes_invalid=0 send_seq=5259 receive_seq=5259 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86565 bytes_read=2042519 bytes_retransmit=0 bytes_invalid=0 send_seq=9818 receive_seq=9818 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998666 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=53.5 th1: temp=52.4 th2: temp=59.1 th3: temp=56.9 sysload=0.40 cputime=360.575 memavail=7395596 print_time=5123.746 buffer_time=1.995 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5100.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22721692 bytes_read=3545729 bytes_retransmit=9 bytes_invalid=0 send_seq=427340 receive_seq=427340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015894 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31726 bytes_read=99706 bytes_retransmit=0 bytes_invalid=0 send_seq=5259 receive_seq=5259 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997266 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154126 bytes_read=4703772 bytes_retransmit=9 bytes_invalid=0 send_seq=21143 receive_seq=21143 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997621 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92115 bytes_read=2079196 bytes_retransmit=9 bytes_invalid=0 send_seq=12379 receive_seq=12379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997455 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=31993 bytes_read=1300964 bytes_retransmit=9 bytes_invalid=0 send_seq=5273 receive_seq=5273 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32479 bytes_read=97749 bytes_retransmit=9 bytes_invalid=0 send_seq=5260 receive_seq=5260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86571 bytes_read=2042875 bytes_retransmit=0 bytes_invalid=0 send_seq=9819 receive_seq=9819 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998652 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=53.1 th1: temp=52.3 th2: temp=59.0 th3: temp=56.9 sysload=0.45 cputime=360.667 memavail=7395596 print_time=5124.959 buffer_time=2.206 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 72 Hz
Stats 5101.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22724556 bytes_read=3546390 bytes_retransmit=9 bytes_invalid=0 send_seq=427404 receive_seq=427404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015890 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31732 bytes_read=99722 bytes_retransmit=0 bytes_invalid=0 send_seq=5260 receive_seq=5260 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997280 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154202 bytes_read=4706842 bytes_retransmit=9 bytes_invalid=0 send_seq=21154 receive_seq=21154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997632 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92121 bytes_read=2079338 bytes_retransmit=9 bytes_invalid=0 send_seq=12380 receive_seq=12380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997484 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=31999 bytes_read=1301258 bytes_retransmit=9 bytes_invalid=0 send_seq=5274 receive_seq=5274 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32485 bytes_read=97765 bytes_retransmit=9 bytes_invalid=0 send_seq=5261 receive_seq=5261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86577 bytes_read=2043231 bytes_retransmit=0 bytes_invalid=0 send_seq=9820 receive_seq=9820 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998661 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=53.3 th1: temp=52.5 th2: temp=59.3 th3: temp=56.9 sysload=0.45 cputime=360.757 memavail=7395596 print_time=5125.881 buffer_time=2.128 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 73 Hz
Stats 5102.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22727666 bytes_read=3547040 bytes_retransmit=9 bytes_invalid=0 send_seq=427472 receive_seq=427472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015885 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31738 bytes_read=99738 bytes_retransmit=0 bytes_invalid=0 send_seq=5261 receive_seq=5261 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997275 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154278 bytes_read=4709900 bytes_retransmit=9 bytes_invalid=0 send_seq=21165 receive_seq=21165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997618 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92127 bytes_read=2079438 bytes_retransmit=9 bytes_invalid=0 send_seq=12381 receive_seq=12381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=32005 bytes_read=1301492 bytes_retransmit=9 bytes_invalid=0 send_seq=5275 receive_seq=5275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32491 bytes_read=97792 bytes_retransmit=9 bytes_invalid=0 send_seq=5262 receive_seq=5262 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86583 bytes_read=2043587 bytes_retransmit=0 bytes_invalid=0 send_seq=9821 receive_seq=9821 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998667 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=53.1 th1: temp=52.2 th2: temp=59.1 th3: temp=56.8 sysload=0.45 cputime=360.843 memavail=7395596 print_time=5126.764 buffer_time=2.011 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 74 Hz
Stats 5103.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22731565 bytes_read=3547769 bytes_retransmit=9 bytes_invalid=0 send_seq=427553 receive_seq=427553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=46 upcoming_bytes=0 freq=400015888 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=31744 bytes_read=99767 bytes_retransmit=0 bytes_invalid=0 send_seq=5262 receive_seq=5262 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997298 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154354 bytes_read=4713048 bytes_retransmit=9 bytes_invalid=0 send_seq=21176 receive_seq=21176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997678 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92133 bytes_read=2079538 bytes_retransmit=9 bytes_invalid=0 send_seq=12382 receive_seq=12382 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997499 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32011 bytes_read=1301741 bytes_retransmit=9 bytes_invalid=0 send_seq=5276 receive_seq=5276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32497 bytes_read=97808 bytes_retransmit=9 bytes_invalid=0 send_seq=5263 receive_seq=5263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86589 bytes_read=2043943 bytes_retransmit=0 bytes_invalid=0 send_seq=9822 receive_seq=9822 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998673 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=53.3 th1: temp=52.3 th2: temp=59.1 th3: temp=56.8 sysload=0.45 cputime=360.941 memavail=7395596 print_time=5127.974 buffer_time=2.221 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 75 Hz
Stats 5104.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22734641 bytes_read=3548424 bytes_retransmit=9 bytes_invalid=0 send_seq=427619 receive_seq=427619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015877 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=31750 bytes_read=99783 bytes_retransmit=0 bytes_invalid=0 send_seq=5263 receive_seq=5263 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999259 adj=49997295 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154430 bytes_read=4716119 bytes_retransmit=9 bytes_invalid=0 send_seq=21187 receive_seq=21187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997651 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92139 bytes_read=2079666 bytes_retransmit=9 bytes_invalid=0 send_seq=12383 receive_seq=12383 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32017 bytes_read=1302035 bytes_retransmit=9 bytes_invalid=0 send_seq=5277 receive_seq=5277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32503 bytes_read=97824 bytes_retransmit=9 bytes_invalid=0 send_seq=5264 receive_seq=5264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86595 bytes_read=2044299 bytes_retransmit=0 bytes_invalid=0 send_seq=9823 receive_seq=9823 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998689 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=53.2 th1: temp=52.3 th2: temp=59.2 th3: temp=56.8 sysload=0.45 cputime=361.031 memavail=7395628 print_time=5128.899 buffer_time=2.144 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 76 Hz
Stats 5105.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22737614 bytes_read=3549064 bytes_retransmit=9 bytes_invalid=0 send_seq=427685 receive_seq=427685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015866 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=31756 bytes_read=99799 bytes_retransmit=0 bytes_invalid=0 send_seq=5264 receive_seq=5264 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999259 adj=49997319 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154506 bytes_read=4719178 bytes_retransmit=9 bytes_invalid=0 send_seq=21198 receive_seq=21198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997655 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92145 bytes_read=2079766 bytes_retransmit=9 bytes_invalid=0 send_seq=12384 receive_seq=12384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997507 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32023 bytes_read=1302269 bytes_retransmit=9 bytes_invalid=0 send_seq=5278 receive_seq=5278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32509 bytes_read=97840 bytes_retransmit=9 bytes_invalid=0 send_seq=5265 receive_seq=5265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999449 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86601 bytes_read=2044655 bytes_retransmit=0 bytes_invalid=0 send_seq=9824 receive_seq=9824 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998695 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=53.0 th1: temp=52.3 th2: temp=59.2 th3: temp=57.0 sysload=0.41 cputime=361.119 memavail=7395628 print_time=5129.767 buffer_time=2.012 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 77 Hz
Stats 5106.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22741583 bytes_read=3549809 bytes_retransmit=9 bytes_invalid=0 send_seq=427766 receive_seq=427766 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=0 freq=400015874 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=31762 bytes_read=99815 bytes_retransmit=0 bytes_invalid=0 send_seq=5265 receive_seq=5265 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999259 adj=49997331 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154582 bytes_read=4722251 bytes_retransmit=9 bytes_invalid=0 send_seq=21209 receive_seq=21209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997651 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92151 bytes_read=2079880 bytes_retransmit=9 bytes_invalid=0 send_seq=12385 receive_seq=12385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32029 bytes_read=1302503 bytes_retransmit=9 bytes_invalid=0 send_seq=5279 receive_seq=5279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997701 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32515 bytes_read=97856 bytes_retransmit=9 bytes_invalid=0 send_seq=5266 receive_seq=5266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86607 bytes_read=2045011 bytes_retransmit=0 bytes_invalid=0 send_seq=9825 receive_seq=9825 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998696 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=53.2 th1: temp=52.4 th2: temp=59.3 th3: temp=56.9 sysload=0.41 cputime=361.217 memavail=7395628 print_time=5130.969 buffer_time=2.213 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 78 Hz
Stats 5107.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22744851 bytes_read=3550489 bytes_retransmit=9 bytes_invalid=0 send_seq=427837 receive_seq=427837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015866 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=31768 bytes_read=99831 bytes_retransmit=0 bytes_invalid=0 send_seq=5266 receive_seq=5266 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997305 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154658 bytes_read=4725323 bytes_retransmit=9 bytes_invalid=0 send_seq=21220 receive_seq=21220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997746 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92157 bytes_read=2080008 bytes_retransmit=9 bytes_invalid=0 send_seq=12386 receive_seq=12386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997495 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32035 bytes_read=1302797 bytes_retransmit=9 bytes_invalid=0 send_seq=5280 receive_seq=5280 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32521 bytes_read=97883 bytes_retransmit=9 bytes_invalid=0 send_seq=5267 receive_seq=5267 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86613 bytes_read=2045367 bytes_retransmit=0 bytes_invalid=0 send_seq=9826 receive_seq=9826 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998674 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=53.3 th1: temp=52.4 th2: temp=59.2 th3: temp=56.8 sysload=0.41 cputime=361.310 memavail=7395164 print_time=5131.919 buffer_time=2.162 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 79 Hz
Stats 5108.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22747747 bytes_read=3551119 bytes_retransmit=9 bytes_invalid=0 send_seq=427901 receive_seq=427901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015865 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31774 bytes_read=99860 bytes_retransmit=0 bytes_invalid=0 send_seq=5267 receive_seq=5267 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997302 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154734 bytes_read=4728399 bytes_retransmit=9 bytes_invalid=0 send_seq=21231 receive_seq=21231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997726 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92163 bytes_read=2080108 bytes_retransmit=9 bytes_invalid=0 send_seq=12387 receive_seq=12387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32041 bytes_read=1303046 bytes_retransmit=9 bytes_invalid=0 send_seq=5281 receive_seq=5281 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32527 bytes_read=97899 bytes_retransmit=9 bytes_invalid=0 send_seq=5268 receive_seq=5268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86619 bytes_read=2045723 bytes_retransmit=0 bytes_invalid=0 send_seq=9827 receive_seq=9827 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998675 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=53.6 th1: temp=52.4 th2: temp=59.1 th3: temp=56.9 sysload=0.41 cputime=361.397 memavail=7395164 print_time=5132.783 buffer_time=2.026 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 80 Hz
Stats 5109.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22751801 bytes_read=3551873 bytes_retransmit=9 bytes_invalid=0 send_seq=427984 receive_seq=427984 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=29 upcoming_bytes=0 freq=400015854 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31780 bytes_read=99876 bytes_retransmit=0 bytes_invalid=0 send_seq=5268 receive_seq=5268 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997281 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154803 bytes_read=4731446 bytes_retransmit=9 bytes_invalid=0 send_seq=21241 receive_seq=21241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997695 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92169 bytes_read=2080208 bytes_retransmit=9 bytes_invalid=0 send_seq=12388 receive_seq=12388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32047 bytes_read=1303280 bytes_retransmit=9 bytes_invalid=0 send_seq=5282 receive_seq=5282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32533 bytes_read=97915 bytes_retransmit=9 bytes_invalid=0 send_seq=5269 receive_seq=5269 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86625 bytes_read=2046079 bytes_retransmit=0 bytes_invalid=0 send_seq=9828 receive_seq=9828 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998683 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.4 th2: temp=59.3 th3: temp=56.9 sysload=0.41 cputime=361.496 memavail=7395164 print_time=5133.989 buffer_time=2.232 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 81 Hz
Stats 5110.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22755146 bytes_read=3552532 bytes_retransmit=9 bytes_invalid=0 send_seq=428055 receive_seq=428055 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015857 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31786 bytes_read=99892 bytes_retransmit=0 bytes_invalid=0 send_seq=5269 receive_seq=5269 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997292 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154879 bytes_read=4734574 bytes_retransmit=9 bytes_invalid=0 send_seq=21252 receive_seq=21252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997691 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92175 bytes_read=2080336 bytes_retransmit=9 bytes_invalid=0 send_seq=12389 receive_seq=12389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997518 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32053 bytes_read=1303574 bytes_retransmit=9 bytes_invalid=0 send_seq=5283 receive_seq=5283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32539 bytes_read=97931 bytes_retransmit=9 bytes_invalid=0 send_seq=5270 receive_seq=5270 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86631 bytes_read=2046435 bytes_retransmit=0 bytes_invalid=0 send_seq=9829 receive_seq=9829 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998688 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=53.3 th1: temp=52.5 th2: temp=59.1 th3: temp=57.0 sysload=0.46 cputime=361.590 memavail=7395164 print_time=5134.926 buffer_time=2.167 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 82 Hz
Stats 5111.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22758066 bytes_read=3553183 bytes_retransmit=9 bytes_invalid=0 send_seq=428120 receive_seq=428120 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015860 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31792 bytes_read=99908 bytes_retransmit=0 bytes_invalid=0 send_seq=5270 receive_seq=5270 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997282 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154955 bytes_read=4737630 bytes_retransmit=9 bytes_invalid=0 send_seq=21263 receive_seq=21263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997772 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92181 bytes_read=2080450 bytes_retransmit=9 bytes_invalid=0 send_seq=12390 receive_seq=12390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32059 bytes_read=1303808 bytes_retransmit=9 bytes_invalid=0 send_seq=5284 receive_seq=5284 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32545 bytes_read=97947 bytes_retransmit=9 bytes_invalid=0 send_seq=5271 receive_seq=5271 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86637 bytes_read=2046791 bytes_retransmit=0 bytes_invalid=0 send_seq=9830 receive_seq=9830 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998685 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=53.3 th1: temp=52.5 th2: temp=59.3 th3: temp=56.9 sysload=0.46 cputime=361.679 memavail=7395164 print_time=5135.791 buffer_time=2.032 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 83 Hz
Testing frequency 84 Hz
Stats 5112.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22762146 bytes_read=3553942 bytes_retransmit=9 bytes_invalid=0 send_seq=428204 receive_seq=428204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=0 freq=400015855 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31798 bytes_read=99924 bytes_retransmit=0 bytes_invalid=0 send_seq=5271 receive_seq=5271 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997300 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155031 bytes_read=4740701 bytes_retransmit=9 bytes_invalid=0 send_seq=21274 receive_seq=21274 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997725 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92187 bytes_read=2080550 bytes_retransmit=9 bytes_invalid=0 send_seq=12391 receive_seq=12391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997501 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32065 bytes_read=1304042 bytes_retransmit=9 bytes_invalid=0 send_seq=5285 receive_seq=5285 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32551 bytes_read=97974 bytes_retransmit=9 bytes_invalid=0 send_seq=5272 receive_seq=5272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86643 bytes_read=2047147 bytes_retransmit=0 bytes_invalid=0 send_seq=9831 receive_seq=9831 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998673 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=53.2 th1: temp=52.4 th2: temp=59.4 th3: temp=57.0 sysload=0.46 cputime=361.781 memavail=7395164 print_time=5136.996 buffer_time=2.237 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5113.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22765646 bytes_read=3554617 bytes_retransmit=9 bytes_invalid=0 send_seq=428277 receive_seq=428277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015855 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=31804 bytes_read=99953 bytes_retransmit=0 bytes_invalid=0 send_seq=5272 receive_seq=5272 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999259 adj=49997296 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155107 bytes_read=4743791 bytes_retransmit=9 bytes_invalid=0 send_seq=21285 receive_seq=21285 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997695 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92193 bytes_read=2080678 bytes_retransmit=9 bytes_invalid=0 send_seq=12392 receive_seq=12392 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32071 bytes_read=1304351 bytes_retransmit=9 bytes_invalid=0 send_seq=5286 receive_seq=5286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32557 bytes_read=97990 bytes_retransmit=9 bytes_invalid=0 send_seq=5273 receive_seq=5273 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86649 bytes_read=2047503 bytes_retransmit=0 bytes_invalid=0 send_seq=9832 receive_seq=9832 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998684 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.4 th2: temp=59.3 th3: temp=56.9 sysload=0.46 cputime=361.874 memavail=7395312 print_time=5137.932 buffer_time=2.172 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 85 Hz
Stats 5114.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22768642 bytes_read=3555257 bytes_retransmit=9 bytes_invalid=0 send_seq=428343 receive_seq=428343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015863 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=31810 bytes_read=99969 bytes_retransmit=0 bytes_invalid=0 send_seq=5273 receive_seq=5273 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999259 adj=49997317 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155183 bytes_read=4746848 bytes_retransmit=9 bytes_invalid=0 send_seq=21296 receive_seq=21296 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997720 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92199 bytes_read=2080778 bytes_retransmit=9 bytes_invalid=0 send_seq=12393 receive_seq=12393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997508 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32077 bytes_read=1304585 bytes_retransmit=9 bytes_invalid=0 send_seq=5287 receive_seq=5287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32563 bytes_read=98006 bytes_retransmit=9 bytes_invalid=0 send_seq=5274 receive_seq=5274 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86655 bytes_read=2047859 bytes_retransmit=0 bytes_invalid=0 send_seq=9833 receive_seq=9833 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998688 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=53.3 th1: temp=52.3 th2: temp=59.2 th3: temp=56.8 sysload=0.46 cputime=361.964 memavail=7395448 print_time=5138.796 buffer_time=2.035 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 86 Hz
Testing frequency 87 Hz
Stats 5115.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22772750 bytes_read=3556011 bytes_retransmit=9 bytes_invalid=0 send_seq=428426 receive_seq=428426 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=0 freq=400015862 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=31816 bytes_read=99985 bytes_retransmit=0 bytes_invalid=0 send_seq=5274 receive_seq=5274 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999259 adj=49997298 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155259 bytes_read=4749919 bytes_retransmit=9 bytes_invalid=0 send_seq=21307 receive_seq=21307 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997680 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92205 bytes_read=2080878 bytes_retransmit=9 bytes_invalid=0 send_seq=12394 receive_seq=12394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32083 bytes_read=1304819 bytes_retransmit=9 bytes_invalid=0 send_seq=5288 receive_seq=5288 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32569 bytes_read=98022 bytes_retransmit=9 bytes_invalid=0 send_seq=5275 receive_seq=5275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86661 bytes_read=2048215 bytes_retransmit=0 bytes_invalid=0 send_seq=9834 receive_seq=9834 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998680 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=53.2 th1: temp=52.6 th2: temp=59.1 th3: temp=57.0 sysload=0.50 cputime=362.067 memavail=7395448 print_time=5139.999 buffer_time=2.238 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Stats 5116.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22776355 bytes_read=3556712 bytes_retransmit=9 bytes_invalid=0 send_seq=428501 receive_seq=428501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015861 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=31822 bytes_read=100001 bytes_retransmit=0 bytes_invalid=0 send_seq=5275 receive_seq=5275 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999259 adj=49997289 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155335 bytes_read=4752989 bytes_retransmit=9 bytes_invalid=0 send_seq=21318 receive_seq=21318 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997654 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92211 bytes_read=2081020 bytes_retransmit=9 bytes_invalid=0 send_seq=12395 receive_seq=12395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32089 bytes_read=1305113 bytes_retransmit=9 bytes_invalid=0 send_seq=5289 receive_seq=5289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32575 bytes_read=98038 bytes_retransmit=9 bytes_invalid=0 send_seq=5276 receive_seq=5276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86667 bytes_read=2048571 bytes_retransmit=0 bytes_invalid=0 send_seq=9835 receive_seq=9835 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998676 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=53.2 th1: temp=52.5 th2: temp=59.3 th3: temp=56.8 sysload=0.50 cputime=362.170 memavail=7396808 print_time=5140.940 buffer_time=2.178 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 88 Hz
Stats 5117.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22779330 bytes_read=3557352 bytes_retransmit=9 bytes_invalid=0 send_seq=428567 receive_seq=428567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015863 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=31828 bytes_read=100017 bytes_retransmit=0 bytes_invalid=0 send_seq=5276 receive_seq=5276 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997288 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155411 bytes_read=4756049 bytes_retransmit=9 bytes_invalid=0 send_seq=21329 receive_seq=21329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997657 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92217 bytes_read=2081120 bytes_retransmit=9 bytes_invalid=0 send_seq=12396 receive_seq=12396 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32095 bytes_read=1305347 bytes_retransmit=9 bytes_invalid=0 send_seq=5290 receive_seq=5290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32581 bytes_read=98065 bytes_retransmit=9 bytes_invalid=0 send_seq=5277 receive_seq=5277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86673 bytes_read=2048927 bytes_retransmit=0 bytes_invalid=0 send_seq=9836 receive_seq=9836 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998676 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.7 th2: temp=59.2 th3: temp=56.9 sysload=0.50 cputime=362.262 memavail=7395576 print_time=5141.808 buffer_time=2.046 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 89 Hz
Testing frequency 90 Hz
Stats 5118.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22783575 bytes_read=3558126 bytes_retransmit=9 bytes_invalid=0 send_seq=428654 receive_seq=428654 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=22 upcoming_bytes=0 freq=400015877 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=31834 bytes_read=100046 bytes_retransmit=0 bytes_invalid=0 send_seq=5277 receive_seq=5277 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999259 adj=49997280 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155487 bytes_read=4759195 bytes_retransmit=9 bytes_invalid=0 send_seq=21340 receive_seq=21340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997648 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92223 bytes_read=2081234 bytes_retransmit=9 bytes_invalid=0 send_seq=12397 receive_seq=12397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32101 bytes_read=1305596 bytes_retransmit=9 bytes_invalid=0 send_seq=5291 receive_seq=5291 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32587 bytes_read=98081 bytes_retransmit=9 bytes_invalid=0 send_seq=5278 receive_seq=5278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86679 bytes_read=2049283 bytes_retransmit=0 bytes_invalid=0 send_seq=9837 receive_seq=9837 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998667 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=53.3 th1: temp=52.5 th2: temp=59.3 th3: temp=57.0 sysload=0.50 cputime=362.368 memavail=7395576 print_time=5143.017 buffer_time=2.253 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5119.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22787149 bytes_read=3558811 bytes_retransmit=9 bytes_invalid=0 send_seq=428729 receive_seq=428729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015873 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=31840 bytes_read=100062 bytes_retransmit=0 bytes_invalid=0 send_seq=5278 receive_seq=5278 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999259 adj=49997267 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155563 bytes_read=4762265 bytes_retransmit=9 bytes_invalid=0 send_seq=21351 receive_seq=21351 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997610 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92229 bytes_read=2081348 bytes_retransmit=9 bytes_invalid=0 send_seq=12398 receive_seq=12398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997484 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32107 bytes_read=1305890 bytes_retransmit=9 bytes_invalid=0 send_seq=5292 receive_seq=5292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997617 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32593 bytes_read=98097 bytes_retransmit=9 bytes_invalid=0 send_seq=5279 receive_seq=5279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86685 bytes_read=2049639 bytes_retransmit=0 bytes_invalid=0 send_seq=9838 receive_seq=9838 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998655 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.4 th2: temp=59.3 th3: temp=56.9 sysload=0.50 cputime=362.461 memavail=7395576 print_time=5143.945 buffer_time=2.181 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 91 Hz
Stats 5120.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22790145 bytes_read=3559446 bytes_retransmit=9 bytes_invalid=0 send_seq=428794 receive_seq=428794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015872 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=31846 bytes_read=100078 bytes_retransmit=0 bytes_invalid=0 send_seq=5279 receive_seq=5279 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997266 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155639 bytes_read=4765322 bytes_retransmit=9 bytes_invalid=0 send_seq=21362 receive_seq=21362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997615 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92235 bytes_read=2081448 bytes_retransmit=9 bytes_invalid=0 send_seq=12399 receive_seq=12399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32113 bytes_read=1306124 bytes_retransmit=9 bytes_invalid=0 send_seq=5293 receive_seq=5293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32599 bytes_read=98113 bytes_retransmit=9 bytes_invalid=0 send_seq=5280 receive_seq=5280 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86691 bytes_read=2049995 bytes_retransmit=0 bytes_invalid=0 send_seq=9839 receive_seq=9839 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998667 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.5 th2: temp=59.1 th3: temp=56.9 sysload=0.54 cputime=362.553 memavail=7395592 print_time=5144.807 buffer_time=2.043 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 92 Hz
Testing frequency 93 Hz
Stats 5121.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22793755 bytes_read=3560177 bytes_retransmit=9 bytes_invalid=0 send_seq=428870 receive_seq=428870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015876 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=31852 bytes_read=100094 bytes_retransmit=0 bytes_invalid=0 send_seq=5280 receive_seq=5280 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997249 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155715 bytes_read=4768393 bytes_retransmit=9 bytes_invalid=0 send_seq=21373 receive_seq=21373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997601 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92241 bytes_read=2081576 bytes_retransmit=9 bytes_invalid=0 send_seq=12400 receive_seq=12400 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997620 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32119 bytes_read=1306358 bytes_retransmit=9 bytes_invalid=0 send_seq=5294 receive_seq=5294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32605 bytes_read=98129 bytes_retransmit=9 bytes_invalid=0 send_seq=5281 receive_seq=5281 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86697 bytes_read=2050351 bytes_retransmit=0 bytes_invalid=0 send_seq=9840 receive_seq=9840 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998667 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=53.5 th1: temp=52.4 th2: temp=59.3 th3: temp=56.9 sysload=0.54 cputime=362.654 memavail=7395592 print_time=5145.750 buffer_time=1.985 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5122.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22798202 bytes_read=3560932 bytes_retransmit=9 bytes_invalid=0 send_seq=428959 receive_seq=428959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015868 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=31858 bytes_read=100110 bytes_retransmit=0 bytes_invalid=0 send_seq=5281 receive_seq=5281 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997228 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155791 bytes_read=4771465 bytes_retransmit=9 bytes_invalid=0 send_seq=21384 receive_seq=21384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997588 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92247 bytes_read=2081690 bytes_retransmit=9 bytes_invalid=0 send_seq=12401 receive_seq=12401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997588 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32125 bytes_read=1306652 bytes_retransmit=9 bytes_invalid=0 send_seq=5295 receive_seq=5295 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32611 bytes_read=98156 bytes_retransmit=9 bytes_invalid=0 send_seq=5282 receive_seq=5282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86703 bytes_read=2050707 bytes_retransmit=0 bytes_invalid=0 send_seq=9841 receive_seq=9841 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998657 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=53.1 th1: temp=52.5 th2: temp=59.4 th3: temp=56.9 sysload=0.54 cputime=362.753 memavail=7395592 print_time=5146.955 buffer_time=2.189 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 94 Hz
Stats 5123.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22801218 bytes_read=3561577 bytes_retransmit=9 bytes_invalid=0 send_seq=429026 receive_seq=429026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015860 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31864 bytes_read=100139 bytes_retransmit=0 bytes_invalid=0 send_seq=5282 receive_seq=5282 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997258 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155860 bytes_read=4774515 bytes_retransmit=9 bytes_invalid=0 send_seq=21394 receive_seq=21394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997609 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92253 bytes_read=2081790 bytes_retransmit=9 bytes_invalid=0 send_seq=12402 receive_seq=12402 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997565 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32131 bytes_read=1306901 bytes_retransmit=9 bytes_invalid=0 send_seq=5296 receive_seq=5296 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32617 bytes_read=98172 bytes_retransmit=9 bytes_invalid=0 send_seq=5283 receive_seq=5283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86709 bytes_read=2051063 bytes_retransmit=0 bytes_invalid=0 send_seq=9842 receive_seq=9842 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998663 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=53.5 th1: temp=52.6 th2: temp=59.3 th3: temp=57.0 sysload=0.54 cputime=362.846 memavail=7395592 print_time=5147.827 buffer_time=2.060 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 95 Hz
Testing frequency 96 Hz
Stats 5124.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22804968 bytes_read=3562311 bytes_retransmit=9 bytes_invalid=0 send_seq=429105 receive_seq=429105 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015860 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31870 bytes_read=100155 bytes_retransmit=0 bytes_invalid=0 send_seq=5283 receive_seq=5283 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997265 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155936 bytes_read=4777644 bytes_retransmit=9 bytes_invalid=0 send_seq=21405 receive_seq=21405 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997625 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92259 bytes_read=2081904 bytes_retransmit=9 bytes_invalid=0 send_seq=12403 receive_seq=12403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997569 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32137 bytes_read=1307135 bytes_retransmit=9 bytes_invalid=0 send_seq=5297 receive_seq=5297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32623 bytes_read=98188 bytes_retransmit=9 bytes_invalid=0 send_seq=5284 receive_seq=5284 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86715 bytes_read=2051419 bytes_retransmit=0 bytes_invalid=0 send_seq=9843 receive_seq=9843 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998666 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=53.4 th1: temp=52.6 th2: temp=59.3 th3: temp=57.0 sysload=0.54 cputime=362.947 memavail=7395592 print_time=5148.763 buffer_time=1.994 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5125.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22809361 bytes_read=3563056 bytes_retransmit=9 bytes_invalid=0 send_seq=429192 receive_seq=429192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015877 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31876 bytes_read=100171 bytes_retransmit=0 bytes_invalid=0 send_seq=5284 receive_seq=5284 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997271 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=156012 bytes_read=4780716 bytes_retransmit=9 bytes_invalid=0 send_seq=21416 receive_seq=21416 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997632 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92265 bytes_read=2082018 bytes_retransmit=9 bytes_invalid=0 send_seq=12404 receive_seq=12404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997565 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32143 bytes_read=1307429 bytes_retransmit=9 bytes_invalid=0 send_seq=5298 receive_seq=5298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32629 bytes_read=98204 bytes_retransmit=9 bytes_invalid=0 send_seq=5285 receive_seq=5285 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=17.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86721 bytes_read=2051775 bytes_retransmit=0 bytes_invalid=0 send_seq=9844 receive_seq=9844 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998662 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=53.2 th1: temp=52.7 th2: temp=59.3 th3: temp=56.9 sysload=0.50 cputime=363.047 memavail=7395592 print_time=5149.959 buffer_time=2.189 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 97 Hz
Stats 5126.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22812451 bytes_read=3563722 bytes_retransmit=9 bytes_invalid=0 send_seq=429260 receive_seq=429260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015871 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31882 bytes_read=100187 bytes_retransmit=0 bytes_invalid=0 send_seq=5285 receive_seq=5285 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997260 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=156088 bytes_read=4783774 bytes_retransmit=9 bytes_invalid=0 send_seq=21427 receive_seq=21427 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997589 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92271 bytes_read=2082118 bytes_retransmit=9 bytes_invalid=0 send_seq=12405 receive_seq=12405 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997555 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32149 bytes_read=1307663 bytes_retransmit=9 bytes_invalid=0 send_seq=5299 receive_seq=5299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997630 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32635 bytes_read=98220 bytes_retransmit=9 bytes_invalid=0 send_seq=5286 receive_seq=5286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86727 bytes_read=2052131 bytes_retransmit=0 bytes_invalid=0 send_seq=9845 receive_seq=9845 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998640 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=53.5 th1: temp=52.6 th2: temp=59.5 th3: temp=57.0 sysload=0.50 cputime=363.140 memavail=7395592 print_time=5150.835 buffer_time=2.064 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 98 Hz
Testing frequency 99 Hz
Stats 5127.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22816238 bytes_read=3564456 bytes_retransmit=9 bytes_invalid=0 send_seq=429339 receive_seq=429339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015887 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31888 bytes_read=100203 bytes_retransmit=0 bytes_invalid=0 send_seq=5286 receive_seq=5286 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999260 adj=49997276 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=156164 bytes_read=4786859 bytes_retransmit=9 bytes_invalid=0 send_seq=21438 receive_seq=21438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997591 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92277 bytes_read=2082246 bytes_retransmit=9 bytes_invalid=0 send_seq=12406 receive_seq=12406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997548 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32155 bytes_read=1307897 bytes_retransmit=9 bytes_invalid=0 send_seq=5300 receive_seq=5300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32641 bytes_read=98247 bytes_retransmit=9 bytes_invalid=0 send_seq=5287 receive_seq=5287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86733 bytes_read=2052487 bytes_retransmit=0 bytes_invalid=0 send_seq=9846 receive_seq=9846 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998671 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=53.3 th1: temp=52.6 th2: temp=59.3 th3: temp=57.0 sysload=0.50 cputime=363.245 memavail=7395100 print_time=5151.763 buffer_time=1.992 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5128.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22820792 bytes_read=3565237 bytes_retransmit=9 bytes_invalid=0 send_seq=429431 receive_seq=429431 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015869 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31900 bytes_read=100248 bytes_retransmit=0 bytes_invalid=0 send_seq=5288 receive_seq=5288 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999260 adj=49997286 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=156246 bytes_read=4789949 bytes_retransmit=9 bytes_invalid=0 send_seq=21450 receive_seq=21450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997563 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92289 bytes_read=2082376 bytes_retransmit=9 bytes_invalid=0 send_seq=12408 receive_seq=12408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997612 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32167 bytes_read=1308222 bytes_retransmit=9 bytes_invalid=0 send_seq=5302 receive_seq=5302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997607 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32653 bytes_read=98279 bytes_retransmit=9 bytes_invalid=0 send_seq=5289 receive_seq=5289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86745 bytes_read=2052859 bytes_retransmit=0 bytes_invalid=0 send_seq=9848 receive_seq=9848 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998651 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=53.3 th1: temp=52.5 th2: temp=59.3 th3: temp=56.8 sysload=0.50 cputime=363.350 memavail=7395100 print_time=5152.968 buffer_time=2.196 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 100 Hz
Stats 5129.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22823875 bytes_read=3565887 bytes_retransmit=9 bytes_invalid=0 send_seq=429499 receive_seq=429499 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015864 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31906 bytes_read=100264 bytes_retransmit=0 bytes_invalid=0 send_seq=5289 receive_seq=5289 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999260 adj=49997310 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=156322 bytes_read=4793005 bytes_retransmit=9 bytes_invalid=0 send_seq=21461 receive_seq=21461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997616 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92295 bytes_read=2082476 bytes_retransmit=9 bytes_invalid=0 send_seq=12409 receive_seq=12409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997579 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32173 bytes_read=1308456 bytes_retransmit=9 bytes_invalid=0 send_seq=5303 receive_seq=5303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997705 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32659 bytes_read=98295 bytes_retransmit=9 bytes_invalid=0 send_seq=5290 receive_seq=5290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86751 bytes_read=2053215 bytes_retransmit=0 bytes_invalid=0 send_seq=9849 receive_seq=9849 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998679 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=53.3 th1: temp=52.6 th2: temp=59.3 th3: temp=57.0 sysload=0.50 cputime=363.444 memavail=7395100 print_time=5153.837 buffer_time=2.064 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 101 Hz
Testing frequency 102 Hz
Stats 5130.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22827791 bytes_read=3566626 bytes_retransmit=9 bytes_invalid=0 send_seq=429579 receive_seq=429579 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015868 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31912 bytes_read=100280 bytes_retransmit=0 bytes_invalid=0 send_seq=5290 receive_seq=5290 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999260 adj=49997310 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=156398 bytes_read=4796090 bytes_retransmit=9 bytes_invalid=0 send_seq=21472 receive_seq=21472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997620 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92301 bytes_read=2082590 bytes_retransmit=9 bytes_invalid=0 send_seq=12410 receive_seq=12410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997565 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32179 bytes_read=1308690 bytes_retransmit=9 bytes_invalid=0 send_seq=5304 receive_seq=5304 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997697 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32665 bytes_read=98311 bytes_retransmit=9 bytes_invalid=0 send_seq=5291 receive_seq=5291 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86757 bytes_read=2053571 bytes_retransmit=0 bytes_invalid=0 send_seq=9850 receive_seq=9850 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998738 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.2 th2: temp=59.3 th3: temp=57.1 sysload=0.54 cputime=363.550 memavail=7395100 print_time=5154.765 buffer_time=1.991 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5131.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22832395 bytes_read=3567410 bytes_retransmit=9 bytes_invalid=0 send_seq=429671 receive_seq=429671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015890 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31918 bytes_read=100296 bytes_retransmit=0 bytes_invalid=0 send_seq=5291 receive_seq=5291 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999262 adj=49997301 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=156474 bytes_read=4799205 bytes_retransmit=9 bytes_invalid=0 send_seq=21483 receive_seq=21483 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997609 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92307 bytes_read=2082704 bytes_retransmit=9 bytes_invalid=0 send_seq=12411 receive_seq=12411 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32185 bytes_read=1308984 bytes_retransmit=9 bytes_invalid=0 send_seq=5305 receive_seq=5305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32671 bytes_read=98327 bytes_retransmit=9 bytes_invalid=0 send_seq=5292 receive_seq=5292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86763 bytes_read=2053927 bytes_retransmit=0 bytes_invalid=0 send_seq=9851 receive_seq=9851 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998729 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=53.3 th1: temp=52.6 th2: temp=59.4 th3: temp=57.0 sysload=0.54 cputime=363.660 memavail=7395116 print_time=5155.970 buffer_time=2.195 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 103 Hz
Stats 5132.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22835550 bytes_read=3568058 bytes_retransmit=9 bytes_invalid=0 send_seq=429739 receive_seq=429739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015887 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31924 bytes_read=100312 bytes_retransmit=0 bytes_invalid=0 send_seq=5292 receive_seq=5292 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999261 adj=49997289 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=156550 bytes_read=4802262 bytes_retransmit=9 bytes_invalid=0 send_seq=21494 receive_seq=21494 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997594 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92313 bytes_read=2082818 bytes_retransmit=9 bytes_invalid=0 send_seq=12412 receive_seq=12412 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32191 bytes_read=1309218 bytes_retransmit=9 bytes_invalid=0 send_seq=5306 receive_seq=5306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32677 bytes_read=98354 bytes_retransmit=9 bytes_invalid=0 send_seq=5293 receive_seq=5293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86769 bytes_read=2054283 bytes_retransmit=0 bytes_invalid=0 send_seq=9852 receive_seq=9852 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998688 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=53.3 th1: temp=52.4 th2: temp=59.3 th3: temp=57.0 sysload=0.54 cputime=363.761 memavail=7395116 print_time=5156.845 buffer_time=2.070 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 104 Hz
Stats 5133.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22839527 bytes_read=3568807 bytes_retransmit=9 bytes_invalid=0 send_seq=429821 receive_seq=429821 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015881 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=31930 bytes_read=100341 bytes_retransmit=0 bytes_invalid=0 send_seq=5293 receive_seq=5293 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999261 adj=49997275 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=156626 bytes_read=4805365 bytes_retransmit=9 bytes_invalid=0 send_seq=21505 receive_seq=21505 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997595 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92319 bytes_read=2082932 bytes_retransmit=9 bytes_invalid=0 send_seq=12413 receive_seq=12413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997540 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32197 bytes_read=1309467 bytes_retransmit=9 bytes_invalid=0 send_seq=5307 receive_seq=5307 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32683 bytes_read=98370 bytes_retransmit=9 bytes_invalid=0 send_seq=5294 receive_seq=5294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86775 bytes_read=2054639 bytes_retransmit=0 bytes_invalid=0 send_seq=9853 receive_seq=9853 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998687 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=53.3 th1: temp=52.8 th2: temp=59.3 th3: temp=57.1 sysload=0.54 cputime=363.871 memavail=7396568 print_time=5157.777 buffer_time=2.002 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 105 Hz
Stats 5134.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22844211 bytes_read=3569587 bytes_retransmit=9 bytes_invalid=0 send_seq=429915 receive_seq=429915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015886 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=31936 bytes_read=100357 bytes_retransmit=0 bytes_invalid=0 send_seq=5294 receive_seq=5294 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999260 adj=49997280 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=156702 bytes_read=4808422 bytes_retransmit=9 bytes_invalid=0 send_seq=21516 receive_seq=21516 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997617 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92325 bytes_read=2083046 bytes_retransmit=9 bytes_invalid=0 send_seq=12414 receive_seq=12414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32203 bytes_read=1309761 bytes_retransmit=9 bytes_invalid=0 send_seq=5308 receive_seq=5308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32689 bytes_read=98386 bytes_retransmit=9 bytes_invalid=0 send_seq=5295 receive_seq=5295 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86781 bytes_read=2054995 bytes_retransmit=0 bytes_invalid=0 send_seq=9854 receive_seq=9854 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998686 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=53.5 th1: temp=52.6 th2: temp=59.3 th3: temp=57.0 sysload=0.54 cputime=363.983 memavail=7396608 print_time=5158.980 buffer_time=2.204 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 106 Hz
Stats 5135.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22847346 bytes_read=3570237 bytes_retransmit=9 bytes_invalid=0 send_seq=429983 receive_seq=429983 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015882 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=31942 bytes_read=100373 bytes_retransmit=0 bytes_invalid=0 send_seq=5295 receive_seq=5295 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999259 adj=49997266 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=156778 bytes_read=4811480 bytes_retransmit=9 bytes_invalid=0 send_seq=21527 receive_seq=21527 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997607 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92331 bytes_read=2083146 bytes_retransmit=9 bytes_invalid=0 send_seq=12415 receive_seq=12415 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997499 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32209 bytes_read=1309995 bytes_retransmit=9 bytes_invalid=0 send_seq=5309 receive_seq=5309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32695 bytes_read=98402 bytes_retransmit=9 bytes_invalid=0 send_seq=5296 receive_seq=5296 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86787 bytes_read=2055351 bytes_retransmit=0 bytes_invalid=0 send_seq=9855 receive_seq=9855 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998673 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.7 th2: temp=59.3 th3: temp=56.9 sysload=0.73 cputime=364.080 memavail=7396356 print_time=5159.849 buffer_time=2.073 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 107 Hz
Stats 5136.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22851422 bytes_read=3571007 bytes_retransmit=9 bytes_invalid=0 send_seq=430066 receive_seq=430066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015880 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=31948 bytes_read=100389 bytes_retransmit=0 bytes_invalid=0 send_seq=5296 receive_seq=5296 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997259 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=156854 bytes_read=4814564 bytes_retransmit=9 bytes_invalid=0 send_seq=21538 receive_seq=21538 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997613 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92337 bytes_read=2083260 bytes_retransmit=9 bytes_invalid=0 send_seq=12416 receive_seq=12416 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32215 bytes_read=1310229 bytes_retransmit=9 bytes_invalid=0 send_seq=5310 receive_seq=5310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32701 bytes_read=98418 bytes_retransmit=9 bytes_invalid=0 send_seq=5297 receive_seq=5297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86793 bytes_read=2055707 bytes_retransmit=0 bytes_invalid=0 send_seq=9856 receive_seq=9856 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998671 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=53.6 th1: temp=52.3 th2: temp=59.3 th3: temp=57.1 sysload=0.73 cputime=364.179 memavail=7396356 print_time=5160.779 buffer_time=2.003 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 108 Hz
Stats 5137.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22856170 bytes_read=3571792 bytes_retransmit=9 bytes_invalid=0 send_seq=430161 receive_seq=430161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015874 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=31954 bytes_read=100405 bytes_retransmit=0 bytes_invalid=0 send_seq=5297 receive_seq=5297 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997250 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=156930 bytes_read=4817620 bytes_retransmit=9 bytes_invalid=0 send_seq=21549 receive_seq=21549 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997626 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92343 bytes_read=2083388 bytes_retransmit=9 bytes_invalid=0 send_seq=12417 receive_seq=12417 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997495 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32221 bytes_read=1310523 bytes_retransmit=9 bytes_invalid=0 send_seq=5311 receive_seq=5311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32707 bytes_read=98445 bytes_retransmit=9 bytes_invalid=0 send_seq=5298 receive_seq=5298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86799 bytes_read=2056063 bytes_retransmit=0 bytes_invalid=0 send_seq=9857 receive_seq=9857 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998677 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=53.8 th1: temp=52.8 th2: temp=59.4 th3: temp=57.1 sysload=0.73 cputime=364.292 memavail=7395144 print_time=5161.983 buffer_time=2.206 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 109 Hz
Stats 5138.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22859376 bytes_read=3572452 bytes_retransmit=9 bytes_invalid=0 send_seq=430231 receive_seq=430231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015871 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31960 bytes_read=100434 bytes_retransmit=0 bytes_invalid=0 send_seq=5298 receive_seq=5298 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997256 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=157006 bytes_read=4820695 bytes_retransmit=9 bytes_invalid=0 send_seq=21560 receive_seq=21560 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000195 adj=63997641 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92349 bytes_read=2083488 bytes_retransmit=9 bytes_invalid=0 send_seq=12418 receive_seq=12418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997501 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32227 bytes_read=1310772 bytes_retransmit=9 bytes_invalid=0 send_seq=5312 receive_seq=5312 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32713 bytes_read=98461 bytes_retransmit=9 bytes_invalid=0 send_seq=5299 receive_seq=5299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86805 bytes_read=2056419 bytes_retransmit=0 bytes_invalid=0 send_seq=9858 receive_seq=9858 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998680 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=53.3 th1: temp=52.9 th2: temp=59.4 th3: temp=57.0 sysload=0.73 cputime=364.391 memavail=7395144 print_time=5162.854 buffer_time=2.076 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 110 Hz
Stats 5139.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22863510 bytes_read=3573216 bytes_retransmit=9 bytes_invalid=0 send_seq=430316 receive_seq=430316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016008 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31966 bytes_read=100450 bytes_retransmit=0 bytes_invalid=0 send_seq=5299 receive_seq=5299 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997260 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=157082 bytes_read=4823837 bytes_retransmit=9 bytes_invalid=0 send_seq=21571 receive_seq=21571 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997642 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92355 bytes_read=2083602 bytes_retransmit=9 bytes_invalid=0 send_seq=12419 receive_seq=12419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32233 bytes_read=1311006 bytes_retransmit=9 bytes_invalid=0 send_seq=5313 receive_seq=5313 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32719 bytes_read=98477 bytes_retransmit=9 bytes_invalid=0 send_seq=5300 receive_seq=5300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86811 bytes_read=2056775 bytes_retransmit=0 bytes_invalid=0 send_seq=9859 receive_seq=9859 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998679 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.0 th1: temp=52.6 th2: temp=59.3 th3: temp=56.9 sysload=0.73 cputime=364.491 memavail=7395144 print_time=5163.783 buffer_time=2.005 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 111 Hz
Stats 5140.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22868315 bytes_read=3573991 bytes_retransmit=9 bytes_invalid=0 send_seq=430409 receive_seq=430409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015995 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31972 bytes_read=100466 bytes_retransmit=0 bytes_invalid=0 send_seq=5300 receive_seq=5300 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997018 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=157151 bytes_read=4826872 bytes_retransmit=9 bytes_invalid=0 send_seq=21581 receive_seq=21581 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997450 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92361 bytes_read=2083716 bytes_retransmit=9 bytes_invalid=0 send_seq=12420 receive_seq=12420 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997194 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32239 bytes_read=1311300 bytes_retransmit=9 bytes_invalid=0 send_seq=5314 receive_seq=5314 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997431 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32725 bytes_read=98493 bytes_retransmit=9 bytes_invalid=0 send_seq=5301 receive_seq=5301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999394 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86817 bytes_read=2057131 bytes_retransmit=0 bytes_invalid=0 send_seq=9860 receive_seq=9860 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998532 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.2 th1: temp=52.7 th2: temp=59.4 th3: temp=57.1 sysload=0.76 cputime=364.603 memavail=7395144 print_time=5164.984 buffer_time=2.205 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 112 Hz
Stats 5141.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22871530 bytes_read=3574647 bytes_retransmit=9 bytes_invalid=0 send_seq=430475 receive_seq=430475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015982 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31978 bytes_read=100482 bytes_retransmit=0 bytes_invalid=0 send_seq=5301 receive_seq=5301 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997114 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=157227 bytes_read=4829928 bytes_retransmit=9 bytes_invalid=0 send_seq=21592 receive_seq=21592 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997543 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92367 bytes_read=2083816 bytes_retransmit=9 bytes_invalid=0 send_seq=12421 receive_seq=12421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997317 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32245 bytes_read=1311534 bytes_retransmit=9 bytes_invalid=0 send_seq=5315 receive_seq=5315 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997506 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32731 bytes_read=98509 bytes_retransmit=9 bytes_invalid=0 send_seq=5302 receive_seq=5302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999420 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86823 bytes_read=2057487 bytes_retransmit=0 bytes_invalid=0 send_seq=9861 receive_seq=9861 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998585 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.3 th1: temp=52.7 th2: temp=59.1 th3: temp=57.0 sysload=0.76 cputime=364.701 memavail=7395144 print_time=5165.858 buffer_time=2.079 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 113 Hz
Stats 5142.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22875697 bytes_read=3575401 bytes_retransmit=9 bytes_invalid=0 send_seq=430559 receive_seq=430559 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015977 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=31984 bytes_read=100498 bytes_retransmit=0 bytes_invalid=0 send_seq=5302 receive_seq=5302 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997173 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=157303 bytes_read=4833014 bytes_retransmit=9 bytes_invalid=0 send_seq=21603 receive_seq=21603 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997571 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92373 bytes_read=2083944 bytes_retransmit=9 bytes_invalid=0 send_seq=12422 receive_seq=12422 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997357 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32251 bytes_read=1311768 bytes_retransmit=9 bytes_invalid=0 send_seq=5316 receive_seq=5316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997540 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32737 bytes_read=98536 bytes_retransmit=9 bytes_invalid=0 send_seq=5303 receive_seq=5303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86829 bytes_read=2057843 bytes_retransmit=0 bytes_invalid=0 send_seq=9862 receive_seq=9862 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998604 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=52.8 th1: temp=52.7 th2: temp=59.1 th3: temp=57.2 sysload=0.76 cputime=364.802 memavail=7395144 print_time=5166.793 buffer_time=2.014 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 114 Hz
Stats 5143.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22880570 bytes_read=3576196 bytes_retransmit=9 bytes_invalid=0 send_seq=430656 receive_seq=430656 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015967 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=31990 bytes_read=100527 bytes_retransmit=0 bytes_invalid=0 send_seq=5303 receive_seq=5303 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997194 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=157379 bytes_read=4836087 bytes_retransmit=9 bytes_invalid=0 send_seq=21614 receive_seq=21614 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997691 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92379 bytes_read=2084058 bytes_retransmit=9 bytes_invalid=0 send_seq=12423 receive_seq=12423 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997372 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32257 bytes_read=1312077 bytes_retransmit=9 bytes_invalid=0 send_seq=5317 receive_seq=5317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997601 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32743 bytes_read=98552 bytes_retransmit=9 bytes_invalid=0 send_seq=5304 receive_seq=5304 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999425 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86835 bytes_read=2058199 bytes_retransmit=0 bytes_invalid=0 send_seq=9863 receive_seq=9863 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998637 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=53.5 th1: temp=52.8 th2: temp=59.3 th3: temp=57.1 sysload=0.76 cputime=364.915 memavail=7395144 print_time=5167.993 buffer_time=2.213 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 115 Hz
Stats 5144.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22883791 bytes_read=3576861 bytes_retransmit=9 bytes_invalid=0 send_seq=430727 receive_seq=430727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015961 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=31996 bytes_read=100543 bytes_retransmit=0 bytes_invalid=0 send_seq=5304 receive_seq=5304 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997241 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=157455 bytes_read=4839133 bytes_retransmit=9 bytes_invalid=0 send_seq=21625 receive_seq=21625 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997741 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92385 bytes_read=2084151 bytes_retransmit=9 bytes_invalid=0 send_seq=12424 receive_seq=12424 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997460 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32263 bytes_read=1312311 bytes_retransmit=9 bytes_invalid=0 send_seq=5318 receive_seq=5318 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32749 bytes_read=98568 bytes_retransmit=9 bytes_invalid=0 send_seq=5305 receive_seq=5305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999431 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86841 bytes_read=2058555 bytes_retransmit=0 bytes_invalid=0 send_seq=9864 receive_seq=9864 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998650 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=53.3 th1: temp=52.5 th2: temp=59.4 th3: temp=57.0 sysload=0.76 cputime=365.014 memavail=7395144 print_time=5168.864 buffer_time=2.083 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 116 Hz
Stats 5145.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22888018 bytes_read=3577630 bytes_retransmit=9 bytes_invalid=0 send_seq=430813 receive_seq=430813 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015951 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=32002 bytes_read=100559 bytes_retransmit=0 bytes_invalid=0 send_seq=5305 receive_seq=5305 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997251 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=157531 bytes_read=4842201 bytes_retransmit=9 bytes_invalid=0 send_seq=21636 receive_seq=21636 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997726 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92391 bytes_read=2084257 bytes_retransmit=9 bytes_invalid=0 send_seq=12425 receive_seq=12425 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997460 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32269 bytes_read=1312545 bytes_retransmit=9 bytes_invalid=0 send_seq=5319 receive_seq=5319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997626 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32755 bytes_read=98584 bytes_retransmit=9 bytes_invalid=0 send_seq=5306 receive_seq=5306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999432 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86847 bytes_read=2058911 bytes_retransmit=0 bytes_invalid=0 send_seq=9865 receive_seq=9865 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998662 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.9 th2: temp=59.5 th3: temp=57.0 sysload=0.70 cputime=365.116 memavail=7395144 print_time=5169.799 buffer_time=2.017 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 117 Hz
Stats 5146.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22892910 bytes_read=3578441 bytes_retransmit=9 bytes_invalid=0 send_seq=430910 receive_seq=430910 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015967 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=32008 bytes_read=100575 bytes_retransmit=0 bytes_invalid=0 send_seq=5306 receive_seq=5306 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997252 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=157607 bytes_read=4845299 bytes_retransmit=9 bytes_invalid=0 send_seq=21647 receive_seq=21647 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997716 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92397 bytes_read=2084363 bytes_retransmit=9 bytes_invalid=0 send_seq=12426 receive_seq=12426 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997469 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32275 bytes_read=1312839 bytes_retransmit=9 bytes_invalid=0 send_seq=5320 receive_seq=5320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997632 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32761 bytes_read=98600 bytes_retransmit=9 bytes_invalid=0 send_seq=5307 receive_seq=5307 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999436 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86853 bytes_read=2059267 bytes_retransmit=0 bytes_invalid=0 send_seq=9866 receive_seq=9866 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998661 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.3 th1: temp=52.9 th2: temp=59.4 th3: temp=57.0 sysload=0.70 cputime=365.231 memavail=7395144 print_time=5171.000 buffer_time=2.218 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 118 Hz
Stats 5147.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22896171 bytes_read=3579106 bytes_retransmit=9 bytes_invalid=0 send_seq=430981 receive_seq=430981 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015956 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=32014 bytes_read=100591 bytes_retransmit=0 bytes_invalid=0 send_seq=5307 receive_seq=5307 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997229 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=157683 bytes_read=4848341 bytes_retransmit=9 bytes_invalid=0 send_seq=21658 receive_seq=21658 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997718 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92403 bytes_read=2084470 bytes_retransmit=9 bytes_invalid=0 send_seq=12427 receive_seq=12427 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997435 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32281 bytes_read=1313073 bytes_retransmit=9 bytes_invalid=0 send_seq=5321 receive_seq=5321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997604 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32767 bytes_read=98627 bytes_retransmit=9 bytes_invalid=0 send_seq=5308 receive_seq=5308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86859 bytes_read=2059623 bytes_retransmit=0 bytes_invalid=0 send_seq=9867 receive_seq=9867 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998636 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.3 th1: temp=53.0 th2: temp=59.4 th3: temp=57.0 sysload=0.70 cputime=365.331 memavail=7394160 print_time=5171.866 buffer_time=2.083 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 119 Hz
Stats 5148.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22900413 bytes_read=3579880 bytes_retransmit=9 bytes_invalid=0 send_seq=431068 receive_seq=431068 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015966 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32020 bytes_read=100620 bytes_retransmit=0 bytes_invalid=0 send_seq=5308 receive_seq=5308 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997243 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=157759 bytes_read=4851437 bytes_retransmit=9 bytes_invalid=0 send_seq=21669 receive_seq=21669 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997713 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92409 bytes_read=2084582 bytes_retransmit=9 bytes_invalid=0 send_seq=12428 receive_seq=12428 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997464 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32287 bytes_read=1313322 bytes_retransmit=9 bytes_invalid=0 send_seq=5322 receive_seq=5322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997615 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32773 bytes_read=98643 bytes_retransmit=9 bytes_invalid=0 send_seq=5309 receive_seq=5309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999433 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86865 bytes_read=2059979 bytes_retransmit=0 bytes_invalid=0 send_seq=9868 receive_seq=9868 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998648 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.5 th1: temp=52.8 th2: temp=59.3 th3: temp=57.0 sysload=0.70 cputime=365.436 memavail=7394160 print_time=5172.792 buffer_time=2.008 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 120 Hz
Stats 5149.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22905419 bytes_read=3580680 bytes_retransmit=9 bytes_invalid=0 send_seq=431166 receive_seq=431166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015956 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32026 bytes_read=100636 bytes_retransmit=0 bytes_invalid=0 send_seq=5309 receive_seq=5309 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997225 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=157835 bytes_read=4854494 bytes_retransmit=9 bytes_invalid=0 send_seq=21680 receive_seq=21680 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997775 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92415 bytes_read=2084696 bytes_retransmit=9 bytes_invalid=0 send_seq=12429 receive_seq=12429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997442 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32293 bytes_read=1313616 bytes_retransmit=9 bytes_invalid=0 send_seq=5323 receive_seq=5323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997606 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32779 bytes_read=98659 bytes_retransmit=9 bytes_invalid=0 send_seq=5310 receive_seq=5310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999429 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86871 bytes_read=2060335 bytes_retransmit=0 bytes_invalid=0 send_seq=9869 receive_seq=9869 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998646 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.3 th1: temp=53.0 th2: temp=59.2 th3: temp=57.0 sysload=0.70 cputime=365.550 memavail=7394188 print_time=5173.996 buffer_time=2.212 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 121 Hz
Stats 5150.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22908728 bytes_read=3581345 bytes_retransmit=9 bytes_invalid=0 send_seq=431237 receive_seq=431237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015942 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32032 bytes_read=100652 bytes_retransmit=0 bytes_invalid=0 send_seq=5310 receive_seq=5310 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997259 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=157911 bytes_read=4857550 bytes_retransmit=9 bytes_invalid=0 send_seq=21691 receive_seq=21691 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997742 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92421 bytes_read=2084796 bytes_retransmit=9 bytes_invalid=0 send_seq=12430 receive_seq=12430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997484 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32299 bytes_read=1313850 bytes_retransmit=9 bytes_invalid=0 send_seq=5324 receive_seq=5324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32785 bytes_read=98675 bytes_retransmit=9 bytes_invalid=0 send_seq=5311 receive_seq=5311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999434 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86877 bytes_read=2060691 bytes_retransmit=0 bytes_invalid=0 send_seq=9870 receive_seq=9870 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998652 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.2 th1: temp=52.6 th2: temp=59.4 th3: temp=56.9 sysload=0.64 cputime=365.658 memavail=7387900 print_time=5174.867 buffer_time=2.083 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 122 Hz
Stats 5151.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22913129 bytes_read=3582145 bytes_retransmit=9 bytes_invalid=0 send_seq=431326 receive_seq=431326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015937 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32038 bytes_read=100668 bytes_retransmit=0 bytes_invalid=0 send_seq=5311 receive_seq=5311 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997273 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=157987 bytes_read=4860636 bytes_retransmit=9 bytes_invalid=0 send_seq=21702 receive_seq=21702 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997754 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92427 bytes_read=2084924 bytes_retransmit=9 bytes_invalid=0 send_seq=12431 receive_seq=12431 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32305 bytes_read=1314084 bytes_retransmit=9 bytes_invalid=0 send_seq=5325 receive_seq=5325 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32791 bytes_read=98691 bytes_retransmit=9 bytes_invalid=0 send_seq=5312 receive_seq=5312 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86883 bytes_read=2061047 bytes_retransmit=0 bytes_invalid=0 send_seq=9871 receive_seq=9871 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998664 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.7 th2: temp=59.3 th3: temp=57.0 sysload=0.64 cputime=365.764 memavail=7393784 print_time=5175.801 buffer_time=2.016 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 123 Hz
Stats 5152.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22918081 bytes_read=3582935 bytes_retransmit=9 bytes_invalid=0 send_seq=431422 receive_seq=431422 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=48 freq=400015944 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32044 bytes_read=100684 bytes_retransmit=0 bytes_invalid=0 send_seq=5312 receive_seq=5312 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997261 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=158063 bytes_read=4863693 bytes_retransmit=9 bytes_invalid=0 send_seq=21713 receive_seq=21713 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997721 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92433 bytes_read=2085038 bytes_retransmit=9 bytes_invalid=0 send_seq=12432 receive_seq=12432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32311 bytes_read=1314378 bytes_retransmit=9 bytes_invalid=0 send_seq=5326 receive_seq=5326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32797 bytes_read=98718 bytes_retransmit=9 bytes_invalid=0 send_seq=5313 receive_seq=5313 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86889 bytes_read=2061403 bytes_retransmit=0 bytes_invalid=0 send_seq=9872 receive_seq=9872 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998659 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.2 th1: temp=52.7 th2: temp=59.6 th3: temp=57.1 sysload=0.64 cputime=365.886 memavail=7393784 print_time=5176.997 buffer_time=2.211 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 124 Hz
Stats 5153.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22921554 bytes_read=3583600 bytes_retransmit=9 bytes_invalid=0 send_seq=431494 receive_seq=431494 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015937 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32050 bytes_read=100713 bytes_retransmit=0 bytes_invalid=0 send_seq=5313 receive_seq=5313 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997250 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=158139 bytes_read=4866825 bytes_retransmit=9 bytes_invalid=0 send_seq=21724 receive_seq=21724 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997740 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92439 bytes_read=2085138 bytes_retransmit=9 bytes_invalid=0 send_seq=12433 receive_seq=12433 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997473 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32317 bytes_read=1314627 bytes_retransmit=9 bytes_invalid=0 send_seq=5327 receive_seq=5327 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32803 bytes_read=98734 bytes_retransmit=9 bytes_invalid=0 send_seq=5314 receive_seq=5314 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86895 bytes_read=2061759 bytes_retransmit=0 bytes_invalid=0 send_seq=9873 receive_seq=9873 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998646 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.5 th1: temp=52.8 th2: temp=59.3 th3: temp=57.2 sysload=0.64 cputime=365.995 memavail=7393784 print_time=5177.875 buffer_time=2.088 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 125 Hz
Stats 5154.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22925917 bytes_read=3584384 bytes_retransmit=9 bytes_invalid=0 send_seq=431583 receive_seq=431583 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015935 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32056 bytes_read=100729 bytes_retransmit=0 bytes_invalid=0 send_seq=5314 receive_seq=5314 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997258 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=158208 bytes_read=4869889 bytes_retransmit=9 bytes_invalid=0 send_seq=21734 receive_seq=21734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997721 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92445 bytes_read=2085266 bytes_retransmit=9 bytes_invalid=0 send_seq=12434 receive_seq=12434 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997474 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32323 bytes_read=1314876 bytes_retransmit=9 bytes_invalid=0 send_seq=5328 receive_seq=5328 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32809 bytes_read=98750 bytes_retransmit=9 bytes_invalid=0 send_seq=5315 receive_seq=5315 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86901 bytes_read=2062115 bytes_retransmit=0 bytes_invalid=0 send_seq=9874 receive_seq=9874 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998651 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.8 th2: temp=59.4 th3: temp=57.0 sysload=0.64 cputime=366.105 memavail=7393784 print_time=5178.806 buffer_time=2.019 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 126 Hz
Testing frequency 127 Hz
Stats 5155.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22930917 bytes_read=3585174 bytes_retransmit=9 bytes_invalid=0 send_seq=431679 receive_seq=431679 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=16 freq=400015935 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32062 bytes_read=100745 bytes_retransmit=0 bytes_invalid=0 send_seq=5315 receive_seq=5315 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997257 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=158284 bytes_read=4872945 bytes_retransmit=9 bytes_invalid=0 send_seq=21745 receive_seq=21745 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997827 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92451 bytes_read=2085366 bytes_retransmit=9 bytes_invalid=0 send_seq=12435 receive_seq=12435 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997473 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32329 bytes_read=1315155 bytes_retransmit=9 bytes_invalid=0 send_seq=5329 receive_seq=5329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32815 bytes_read=98766 bytes_retransmit=9 bytes_invalid=0 send_seq=5316 receive_seq=5316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999444 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86907 bytes_read=2062455 bytes_retransmit=0 bytes_invalid=0 send_seq=9875 receive_seq=9875 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998657 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=53.0 th1: temp=53.1 th2: temp=59.2 th3: temp=57.1 sysload=0.59 cputime=366.227 memavail=7393784 print_time=5180.007 buffer_time=2.219 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5156.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22934275 bytes_read=3585850 bytes_retransmit=9 bytes_invalid=0 send_seq=431749 receive_seq=431749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015937 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32068 bytes_read=100761 bytes_retransmit=0 bytes_invalid=0 send_seq=5316 receive_seq=5316 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997264 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=158360 bytes_read=4876001 bytes_retransmit=9 bytes_invalid=0 send_seq=21756 receive_seq=21756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997753 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92457 bytes_read=2085466 bytes_retransmit=9 bytes_invalid=0 send_seq=12436 receive_seq=12436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32335 bytes_read=1315389 bytes_retransmit=9 bytes_invalid=0 send_seq=5330 receive_seq=5330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997632 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32821 bytes_read=98782 bytes_retransmit=9 bytes_invalid=0 send_seq=5317 receive_seq=5317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86913 bytes_read=2062811 bytes_retransmit=0 bytes_invalid=0 send_seq=9876 receive_seq=9876 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998654 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=53.2 th1: temp=52.9 th2: temp=59.6 th3: temp=57.0 sysload=0.59 cputime=366.324 memavail=7393784 print_time=5180.876 buffer_time=2.088 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 128 Hz
Stats 5157.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22938753 bytes_read=3586639 bytes_retransmit=9 bytes_invalid=0 send_seq=431839 receive_seq=431839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015936 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32074 bytes_read=100777 bytes_retransmit=0 bytes_invalid=0 send_seq=5317 receive_seq=5317 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997269 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=158436 bytes_read=4879086 bytes_retransmit=9 bytes_invalid=0 send_seq=21767 receive_seq=21767 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997713 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92463 bytes_read=2085608 bytes_retransmit=9 bytes_invalid=0 send_seq=12437 receive_seq=12437 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997486 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32341 bytes_read=1315638 bytes_retransmit=9 bytes_invalid=0 send_seq=5331 receive_seq=5331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32827 bytes_read=98809 bytes_retransmit=9 bytes_invalid=0 send_seq=5318 receive_seq=5318 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86919 bytes_read=2063167 bytes_retransmit=0 bytes_invalid=0 send_seq=9877 receive_seq=9877 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998658 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.8 th2: temp=59.5 th3: temp=57.1 sysload=0.59 cputime=366.434 memavail=7393068 print_time=5181.807 buffer_time=2.019 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 129 Hz
Testing frequency 130 Hz
Stats 5158.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22943633 bytes_read=3587429 bytes_retransmit=9 bytes_invalid=0 send_seq=431935 receive_seq=431935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=112 freq=400015930 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32080 bytes_read=100806 bytes_retransmit=0 bytes_invalid=0 send_seq=5318 receive_seq=5318 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997277 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=158512 bytes_read=4882160 bytes_retransmit=9 bytes_invalid=0 send_seq=21778 receive_seq=21778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997679 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92469 bytes_read=2085708 bytes_retransmit=9 bytes_invalid=0 send_seq=12438 receive_seq=12438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997482 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32347 bytes_read=1315932 bytes_retransmit=9 bytes_invalid=0 send_seq=5332 receive_seq=5332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32833 bytes_read=98825 bytes_retransmit=9 bytes_invalid=0 send_seq=5319 receive_seq=5319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86925 bytes_read=2063523 bytes_retransmit=0 bytes_invalid=0 send_seq=9878 receive_seq=9878 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998654 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=53.3 th1: temp=52.9 th2: temp=59.5 th3: temp=57.4 sysload=0.59 cputime=366.556 memavail=7393068 print_time=5183.007 buffer_time=2.218 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5159.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22947246 bytes_read=3588109 bytes_retransmit=9 bytes_invalid=0 send_seq=432009 receive_seq=432009 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015921 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32086 bytes_read=100822 bytes_retransmit=0 bytes_invalid=0 send_seq=5319 receive_seq=5319 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997285 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=158588 bytes_read=4885217 bytes_retransmit=9 bytes_invalid=0 send_seq=21789 receive_seq=21789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997827 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92475 bytes_read=2085808 bytes_retransmit=9 bytes_invalid=0 send_seq=12439 receive_seq=12439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997502 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32353 bytes_read=1316166 bytes_retransmit=9 bytes_invalid=0 send_seq=5333 receive_seq=5333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32839 bytes_read=98841 bytes_retransmit=9 bytes_invalid=0 send_seq=5320 receive_seq=5320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86931 bytes_read=2063879 bytes_retransmit=0 bytes_invalid=0 send_seq=9879 receive_seq=9879 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998662 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=53.5 th1: temp=52.9 th2: temp=59.5 th3: temp=57.0 sysload=0.59 cputime=366.659 memavail=7393068 print_time=5183.879 buffer_time=2.089 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 131 Hz
Stats 5160.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22951718 bytes_read=3588898 bytes_retransmit=9 bytes_invalid=0 send_seq=432099 receive_seq=432099 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015926 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32092 bytes_read=100838 bytes_retransmit=0 bytes_invalid=0 send_seq=5320 receive_seq=5320 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997296 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=158664 bytes_read=4888304 bytes_retransmit=9 bytes_invalid=0 send_seq=21800 receive_seq=21800 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997813 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92481 bytes_read=2085936 bytes_retransmit=9 bytes_invalid=0 send_seq=12440 receive_seq=12440 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32359 bytes_read=1316415 bytes_retransmit=9 bytes_invalid=0 send_seq=5334 receive_seq=5334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997697 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32845 bytes_read=98857 bytes_retransmit=9 bytes_invalid=0 send_seq=5321 receive_seq=5321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86937 bytes_read=2064235 bytes_retransmit=0 bytes_invalid=0 send_seq=9880 receive_seq=9880 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998675 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=53.3 th1: temp=52.9 th2: temp=59.4 th3: temp=57.1 sysload=0.70 cputime=366.769 memavail=7393088 print_time=5184.810 buffer_time=2.019 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 132 Hz
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Stats 5161.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22956594 bytes_read=3589699 bytes_retransmit=9 bytes_invalid=0 send_seq=432194 receive_seq=432194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=479 freq=400015931 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32098 bytes_read=100854 bytes_retransmit=0 bytes_invalid=0 send_seq=5321 receive_seq=5321 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997278 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=158740 bytes_read=4891420 bytes_retransmit=9 bytes_invalid=0 send_seq=21811 receive_seq=21811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997744 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92487 bytes_read=2086036 bytes_retransmit=9 bytes_invalid=0 send_seq=12441 receive_seq=12441 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997529 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32365 bytes_read=1316694 bytes_retransmit=9 bytes_invalid=0 send_seq=5335 receive_seq=5335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32851 bytes_read=98873 bytes_retransmit=9 bytes_invalid=0 send_seq=5322 receive_seq=5322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86943 bytes_read=2064591 bytes_retransmit=0 bytes_invalid=0 send_seq=9881 receive_seq=9881 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998679 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.9 th2: temp=59.4 th3: temp=56.9 sysload=0.70 cputime=366.893 memavail=7393088 print_time=5186.060 buffer_time=2.268 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5162.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22957456 bytes_read=3590159 bytes_retransmit=9 bytes_invalid=0 send_seq=432224 receive_seq=432224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015925 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32104 bytes_read=100870 bytes_retransmit=0 bytes_invalid=0 send_seq=5322 receive_seq=5322 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997277 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=158816 bytes_read=4894479 bytes_retransmit=9 bytes_invalid=0 send_seq=21822 receive_seq=21822 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997681 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92493 bytes_read=2086150 bytes_retransmit=9 bytes_invalid=0 send_seq=12442 receive_seq=12442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32371 bytes_read=1316928 bytes_retransmit=9 bytes_invalid=0 send_seq=5336 receive_seq=5336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32857 bytes_read=98900 bytes_retransmit=9 bytes_invalid=0 send_seq=5323 receive_seq=5323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86949 bytes_read=2064947 bytes_retransmit=0 bytes_invalid=0 send_seq=9882 receive_seq=9882 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998671 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=53.5 th1: temp=52.9 th2: temp=59.4 th3: temp=57.1 sysload=0.70 cputime=366.957 memavail=7393088 print_time=5186.060 buffer_time=1.267 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5163.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22957754 bytes_read=3590611 bytes_retransmit=9 bytes_invalid=0 send_seq=432247 receive_seq=432247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015922 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=32110 bytes_read=100898 bytes_retransmit=0 bytes_invalid=0 send_seq=5323 receive_seq=5323 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997283 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=158892 bytes_read=4897582 bytes_retransmit=9 bytes_invalid=0 send_seq=21833 receive_seq=21833 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997665 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92499 bytes_read=2086278 bytes_retransmit=9 bytes_invalid=0 send_seq=12443 receive_seq=12443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997553 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32377 bytes_read=1317192 bytes_retransmit=9 bytes_invalid=0 send_seq=5337 receive_seq=5337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32863 bytes_read=98916 bytes_retransmit=9 bytes_invalid=0 send_seq=5324 receive_seq=5324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86955 bytes_read=2065303 bytes_retransmit=0 bytes_invalid=0 send_seq=9883 receive_seq=9883 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998674 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.9 th2: temp=59.4 th3: temp=57.2 sysload=0.70 cputime=367.017 memavail=7393088 print_time=5186.060 buffer_time=0.267 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
LIS2DW finished 'toolboard_t0' measurements
Resonances data written to /tmp/resonances_x_250.000_250.000_20.000_t0.csv file
Probing point (250.000, 250.000, 20.000)
Stats 5164.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22958151 bytes_read=3591041 bytes_retransmit=9 bytes_invalid=0 send_seq=432272 receive_seq=432272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015909 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=32116 bytes_read=100913 bytes_retransmit=0 bytes_invalid=0 send_seq=5324 receive_seq=5324 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999259 adj=49997276 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=158974 bytes_read=4898805 bytes_retransmit=9 bytes_invalid=0 send_seq=21843 receive_seq=21843 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997664 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92505 bytes_read=2086378 bytes_retransmit=9 bytes_invalid=0 send_seq=12444 receive_seq=12444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997589 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32383 bytes_read=1317471 bytes_retransmit=9 bytes_invalid=0 send_seq=5338 receive_seq=5338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32869 bytes_read=98932 bytes_retransmit=9 bytes_invalid=0 send_seq=5325 receive_seq=5325 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999449 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86961 bytes_read=2065659 bytes_retransmit=0 bytes_invalid=0 send_seq=9884 receive_seq=9884 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998682 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.8 th2: temp=59.4 th3: temp=57.1 sysload=0.70 cputime=367.129 memavail=7395444 print_time=5187.032 buffer_time=0.239 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t0' measurements
toolhead: max_velocity: 600.000000
max_accel: 8379.841000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance testing
Testing frequency 10 Hz
Testing frequency 11 Hz
Testing frequency 12 Hz
Stats 5165.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22967320 bytes_read=3592196 bytes_retransmit=9 bytes_invalid=0 send_seq=432441 receive_seq=432441 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=430 freq=400015908 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=32122 bytes_read=100928 bytes_retransmit=0 bytes_invalid=0 send_seq=5325 receive_seq=5325 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997355 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=159136 bytes_read=4901120 bytes_retransmit=9 bytes_invalid=0 send_seq=21862 receive_seq=21862 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997740 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92511 bytes_read=2086478 bytes_retransmit=9 bytes_invalid=0 send_seq=12445 receive_seq=12445 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997799 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32389 bytes_read=1317705 bytes_retransmit=9 bytes_invalid=0 send_seq=5339 receive_seq=5339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997720 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32875 bytes_read=98948 bytes_retransmit=9 bytes_invalid=0 send_seq=5326 receive_seq=5326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999458 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86967 bytes_read=2066015 bytes_retransmit=0 bytes_invalid=0 send_seq=9885 receive_seq=9885 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998726 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=53.5 th1: temp=53.1 th2: temp=59.5 th3: temp=57.2 sysload=0.64 cputime=367.320 memavail=7395528 print_time=5190.196 buffer_time=2.401 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 13 Hz
Stats 5166.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22970676 bytes_read=3592906 bytes_retransmit=9 bytes_invalid=0 send_seq=432512 receive_seq=432512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015904 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=32128 bytes_read=100943 bytes_retransmit=0 bytes_invalid=0 send_seq=5326 receive_seq=5326 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997289 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=159212 bytes_read=4904206 bytes_retransmit=9 bytes_invalid=0 send_seq=21873 receive_seq=21873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997678 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92517 bytes_read=2086606 bytes_retransmit=9 bytes_invalid=0 send_seq=12446 receive_seq=12446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997577 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32395 bytes_read=1317942 bytes_retransmit=9 bytes_invalid=0 send_seq=5340 receive_seq=5340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32881 bytes_read=98964 bytes_retransmit=9 bytes_invalid=0 send_seq=5327 receive_seq=5327 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86973 bytes_read=2066371 bytes_retransmit=0 bytes_invalid=0 send_seq=9886 receive_seq=9886 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998674 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.9 th2: temp=59.4 th3: temp=57.2 sysload=0.64 cputime=367.398 memavail=7395528 print_time=5190.789 buffer_time=1.994 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 14 Hz
Stats 5167.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22975400 bytes_read=3593666 bytes_retransmit=9 bytes_invalid=0 send_seq=432602 receive_seq=432602 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=26 upcoming_bytes=874 freq=400015893 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=32134 bytes_read=100958 bytes_retransmit=0 bytes_invalid=0 send_seq=5327 receive_seq=5327 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997284 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=159288 bytes_read=4907245 bytes_retransmit=9 bytes_invalid=0 send_seq=21884 receive_seq=21884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997779 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92523 bytes_read=2086720 bytes_retransmit=9 bytes_invalid=0 send_seq=12447 receive_seq=12447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997559 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32401 bytes_read=1318202 bytes_retransmit=9 bytes_invalid=0 send_seq=5341 receive_seq=5341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32887 bytes_read=98991 bytes_retransmit=9 bytes_invalid=0 send_seq=5328 receive_seq=5328 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86979 bytes_read=2066727 bytes_retransmit=0 bytes_invalid=0 send_seq=9887 receive_seq=9887 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998692 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=53.3 th1: temp=52.6 th2: temp=59.5 th3: temp=57.0 sysload=0.64 cputime=367.493 memavail=7390252 print_time=5192.061 buffer_time=2.265 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 15 Hz
Stats 5168.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22980287 bytes_read=3594446 bytes_retransmit=9 bytes_invalid=0 send_seq=432696 receive_seq=432696 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=16 freq=400015903 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=32140 bytes_read=100987 bytes_retransmit=0 bytes_invalid=0 send_seq=5328 receive_seq=5328 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997291 toolboard_t0: mcu_awake=0.262 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=159364 bytes_read=4910319 bytes_retransmit=9 bytes_invalid=0 send_seq=21895 receive_seq=21895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997841 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92529 bytes_read=2086820 bytes_retransmit=9 bytes_invalid=0 send_seq=12448 receive_seq=12448 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32407 bytes_read=1318435 bytes_retransmit=9 bytes_invalid=0 send_seq=5342 receive_seq=5342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32893 bytes_read=99007 bytes_retransmit=9 bytes_invalid=0 send_seq=5329 receive_seq=5329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86985 bytes_read=2067083 bytes_retransmit=0 bytes_invalid=0 send_seq=9888 receive_seq=9888 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998690 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=53.5 th1: temp=52.8 th2: temp=59.3 th3: temp=56.9 sysload=0.64 cputime=367.591 memavail=7394884 print_time=5192.916 buffer_time=2.119 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 16 Hz
Stats 5169.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22984235 bytes_read=3595180 bytes_retransmit=9 bytes_invalid=0 send_seq=432775 receive_seq=432775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=1223 freq=400015909 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=32146 bytes_read=101003 bytes_retransmit=0 bytes_invalid=0 send_seq=5329 receive_seq=5329 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997268 toolboard_t0: mcu_awake=0.262 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=159440 bytes_read=4913405 bytes_retransmit=9 bytes_invalid=0 send_seq=21906 receive_seq=21906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997770 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92535 bytes_read=2086948 bytes_retransmit=9 bytes_invalid=0 send_seq=12449 receive_seq=12449 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997575 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32413 bytes_read=1318667 bytes_retransmit=9 bytes_invalid=0 send_seq=5343 receive_seq=5343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32899 bytes_read=99023 bytes_retransmit=9 bytes_invalid=0 send_seq=5330 receive_seq=5330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86991 bytes_read=2067439 bytes_retransmit=0 bytes_invalid=0 send_seq=9889 receive_seq=9889 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998673 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.9 th2: temp=59.4 th3: temp=57.0 sysload=0.64 cputime=367.680 memavail=7394884 print_time=5193.881 buffer_time=2.084 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 17 Hz
Stats 5170.2: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=22989463 bytes_read=3595975 bytes_retransmit=9 bytes_invalid=0 send_seq=432872 receive_seq=432872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=2181 freq=400015896 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=32152 bytes_read=101019 bytes_retransmit=0 bytes_invalid=0 send_seq=5330 receive_seq=5330 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997256 toolboard_t0: mcu_awake=0.262 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=159509 bytes_read=4916439 bytes_retransmit=9 bytes_invalid=0 send_seq=21916 receive_seq=21916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997709 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92541 bytes_read=2087048 bytes_retransmit=9 bytes_invalid=0 send_seq=12450 receive_seq=12450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997527 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32419 bytes_read=1318927 bytes_retransmit=9 bytes_invalid=0 send_seq=5344 receive_seq=5344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32905 bytes_read=99039 bytes_retransmit=9 bytes_invalid=0 send_seq=5331 receive_seq=5331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=86997 bytes_read=2067795 bytes_retransmit=0 bytes_invalid=0 send_seq=9890 receive_seq=9890 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998680 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.9 th2: temp=59.4 th3: temp=57.0 sysload=0.59 cputime=367.781 memavail=7394636 print_time=5195.084 buffer_time=2.286 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 18 Hz
Stats 5171.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=22994879 bytes_read=3596811 bytes_retransmit=9 bytes_invalid=0 send_seq=432974 receive_seq=432974 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=1453 freq=400015888 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=32158 bytes_read=101035 bytes_retransmit=0 bytes_invalid=0 send_seq=5331 receive_seq=5331 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997275 toolboard_t0: mcu_awake=0.262 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=159585 bytes_read=4919495 bytes_retransmit=9 bytes_invalid=0 send_seq=21927 receive_seq=21927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997711 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92547 bytes_read=2087148 bytes_retransmit=9 bytes_invalid=0 send_seq=12451 receive_seq=12451 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997526 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32425 bytes_read=1319149 bytes_retransmit=9 bytes_invalid=0 send_seq=5345 receive_seq=5345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32911 bytes_read=99055 bytes_retransmit=9 bytes_invalid=0 send_seq=5332 receive_seq=5332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87003 bytes_read=2068151 bytes_retransmit=0 bytes_invalid=0 send_seq=9891 receive_seq=9891 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998690 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.9 th2: temp=59.2 th3: temp=56.9 sysload=0.59 cputime=367.877 memavail=7394636 print_time=5196.030 buffer_time=2.232 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 19 Hz
Stats 5172.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=22999428 bytes_read=3597590 bytes_retransmit=9 bytes_invalid=0 send_seq=433062 receive_seq=433062 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=2195 freq=400015883 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=32164 bytes_read=101051 bytes_retransmit=0 bytes_invalid=0 send_seq=5332 receive_seq=5332 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997282 toolboard_t0: mcu_awake=0.262 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=159661 bytes_read=4922579 bytes_retransmit=9 bytes_invalid=0 send_seq=21938 receive_seq=21938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997699 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92553 bytes_read=2087290 bytes_retransmit=9 bytes_invalid=0 send_seq=12452 receive_seq=12452 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997534 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32431 bytes_read=1319413 bytes_retransmit=9 bytes_invalid=0 send_seq=5346 receive_seq=5346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32917 bytes_read=99082 bytes_retransmit=9 bytes_invalid=0 send_seq=5333 receive_seq=5333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87009 bytes_read=2068507 bytes_retransmit=0 bytes_invalid=0 send_seq=9892 receive_seq=9892 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998691 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.3 th1: temp=52.8 th2: temp=59.3 th3: temp=56.9 sysload=0.59 cputime=367.970 memavail=7394636 print_time=5196.851 buffer_time=2.052 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 20 Hz
Stats 5173.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=23005251 bytes_read=3598440 bytes_retransmit=9 bytes_invalid=0 send_seq=433170 receive_seq=433170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=1549 freq=400015878 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=32170 bytes_read=101067 bytes_retransmit=0 bytes_invalid=0 send_seq=5333 receive_seq=5333 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997291 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=159737 bytes_read=4925711 bytes_retransmit=9 bytes_invalid=0 send_seq=21949 receive_seq=21949 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997754 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92559 bytes_read=2087390 bytes_retransmit=9 bytes_invalid=0 send_seq=12453 receive_seq=12453 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32437 bytes_read=1319692 bytes_retransmit=9 bytes_invalid=0 send_seq=5347 receive_seq=5347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32923 bytes_read=99098 bytes_retransmit=9 bytes_invalid=0 send_seq=5334 receive_seq=5334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87015 bytes_read=2068863 bytes_retransmit=0 bytes_invalid=0 send_seq=9893 receive_seq=9893 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998693 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.7 th2: temp=59.1 th3: temp=56.6 sysload=0.59 cputime=368.069 memavail=7394636 print_time=5197.836 buffer_time=2.037 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 21 Hz
Stats 5174.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=23011339 bytes_read=3599313 bytes_retransmit=9 bytes_invalid=0 send_seq=433283 receive_seq=433283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=26 upcoming_bytes=2750 freq=400015871 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32176 bytes_read=101096 bytes_retransmit=0 bytes_invalid=0 send_seq=5334 receive_seq=5334 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997275 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=159813 bytes_read=4928769 bytes_retransmit=9 bytes_invalid=0 send_seq=21960 receive_seq=21960 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997726 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92565 bytes_read=2087490 bytes_retransmit=9 bytes_invalid=0 send_seq=12454 receive_seq=12454 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32443 bytes_read=1319926 bytes_retransmit=9 bytes_invalid=0 send_seq=5348 receive_seq=5348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32929 bytes_read=99114 bytes_retransmit=9 bytes_invalid=0 send_seq=5335 receive_seq=5335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87021 bytes_read=2069219 bytes_retransmit=0 bytes_invalid=0 send_seq=9894 receive_seq=9894 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998683 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=53.2 th1: temp=53.0 th2: temp=59.0 th3: temp=56.7 sysload=0.59 cputime=368.176 memavail=7394636 print_time=5199.076 buffer_time=2.277 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 22 Hz
Stats 5175.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=23016511 bytes_read=3600139 bytes_retransmit=9 bytes_invalid=0 send_seq=433381 receive_seq=433381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=3377 freq=400015866 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32182 bytes_read=101112 bytes_retransmit=0 bytes_invalid=0 send_seq=5335 receive_seq=5335 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997272 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=159889 bytes_read=4931857 bytes_retransmit=9 bytes_invalid=0 send_seq=21971 receive_seq=21971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997708 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92571 bytes_read=2087618 bytes_retransmit=9 bytes_invalid=0 send_seq=12455 receive_seq=12455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32449 bytes_read=1320190 bytes_retransmit=9 bytes_invalid=0 send_seq=5349 receive_seq=5349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32935 bytes_read=99130 bytes_retransmit=9 bytes_invalid=0 send_seq=5336 receive_seq=5336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87027 bytes_read=2069575 bytes_retransmit=0 bytes_invalid=0 send_seq=9895 receive_seq=9895 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998684 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=53.1 th1: temp=52.9 th2: temp=59.0 th3: temp=56.7 sysload=0.55 cputime=368.273 memavail=7394436 print_time=5199.931 buffer_time=2.131 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 23 Hz
Stats 5176.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23022738 bytes_read=3601050 bytes_retransmit=9 bytes_invalid=0 send_seq=433498 receive_seq=433498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=2501 freq=400015859 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32188 bytes_read=101128 bytes_retransmit=0 bytes_invalid=0 send_seq=5336 receive_seq=5336 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997270 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=159965 bytes_read=4934914 bytes_retransmit=9 bytes_invalid=0 send_seq=21982 receive_seq=21982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997680 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92577 bytes_read=2087718 bytes_retransmit=9 bytes_invalid=0 send_seq=12456 receive_seq=12456 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32455 bytes_read=1320454 bytes_retransmit=9 bytes_invalid=0 send_seq=5350 receive_seq=5350 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32941 bytes_read=99146 bytes_retransmit=9 bytes_invalid=0 send_seq=5337 receive_seq=5337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87033 bytes_read=2069931 bytes_retransmit=0 bytes_invalid=0 send_seq=9896 receive_seq=9896 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998686 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=53.1 th1: temp=53.0 th2: temp=58.7 th3: temp=56.6 sysload=0.55 cputime=368.375 memavail=7394436 print_time=5200.851 buffer_time=2.051 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 24 Hz
Stats 5177.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23029265 bytes_read=3601955 bytes_retransmit=9 bytes_invalid=0 send_seq=433617 receive_seq=433617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=36 upcoming_bytes=3847 freq=400015868 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32194 bytes_read=101144 bytes_retransmit=0 bytes_invalid=0 send_seq=5337 receive_seq=5337 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997268 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=160041 bytes_read=4937972 bytes_retransmit=9 bytes_invalid=0 send_seq=21993 receive_seq=21993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997674 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92583 bytes_read=2087832 bytes_retransmit=9 bytes_invalid=0 send_seq=12457 receive_seq=12457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32461 bytes_read=1320688 bytes_retransmit=9 bytes_invalid=0 send_seq=5351 receive_seq=5351 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32947 bytes_read=99173 bytes_retransmit=9 bytes_invalid=0 send_seq=5338 receive_seq=5338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87039 bytes_read=2070287 bytes_retransmit=0 bytes_invalid=0 send_seq=9897 receive_seq=9897 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998685 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=53.1 th1: temp=52.8 th2: temp=58.8 th3: temp=56.6 sysload=0.55 cputime=368.488 memavail=7393688 print_time=5202.084 buffer_time=2.284 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 25 Hz
Stats 5178.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23035010 bytes_read=3602824 bytes_retransmit=9 bytes_invalid=0 send_seq=433723 receive_seq=433723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=4547 freq=400015865 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32200 bytes_read=101160 bytes_retransmit=0 bytes_invalid=0 send_seq=5338 receive_seq=5338 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997252 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=160117 bytes_read=4941075 bytes_retransmit=9 bytes_invalid=0 send_seq=22004 receive_seq=22004 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997632 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92589 bytes_read=2087960 bytes_retransmit=9 bytes_invalid=0 send_seq=12458 receive_seq=12458 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997486 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=32467 bytes_read=1320967 bytes_retransmit=9 bytes_invalid=0 send_seq=5352 receive_seq=5352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997669 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32953 bytes_read=99189 bytes_retransmit=9 bytes_invalid=0 send_seq=5339 receive_seq=5339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87045 bytes_read=2070643 bytes_retransmit=0 bytes_invalid=0 send_seq=9898 receive_seq=9898 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998681 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=53.3 th1: temp=53.1 th2: temp=58.9 th3: temp=56.5 sysload=0.55 cputime=368.586 memavail=7393688 print_time=5202.961 buffer_time=2.160 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 26 Hz
Stats 5179.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23041786 bytes_read=3603744 bytes_retransmit=9 bytes_invalid=0 send_seq=433845 receive_seq=433845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=4127 freq=400015879 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32206 bytes_read=101189 bytes_retransmit=0 bytes_invalid=0 send_seq=5339 receive_seq=5339 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997245 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=160193 bytes_read=4944133 bytes_retransmit=9 bytes_invalid=0 send_seq=22015 receive_seq=22015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997712 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92595 bytes_read=2088060 bytes_retransmit=9 bytes_invalid=0 send_seq=12459 receive_seq=12459 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997477 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=32473 bytes_read=1321231 bytes_retransmit=9 bytes_invalid=0 send_seq=5353 receive_seq=5353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32959 bytes_read=99205 bytes_retransmit=9 bytes_invalid=0 send_seq=5340 receive_seq=5340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87051 bytes_read=2070999 bytes_retransmit=0 bytes_invalid=0 send_seq=9899 receive_seq=9899 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998681 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=53.2 th1: temp=53.0 th2: temp=58.7 th3: temp=56.4 sysload=0.55 cputime=368.686 memavail=7393688 print_time=5203.928 buffer_time=2.126 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 27 Hz
Stats 5180.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23048905 bytes_read=3604699 bytes_retransmit=9 bytes_invalid=0 send_seq=433974 receive_seq=433974 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=5260 freq=400015875 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32212 bytes_read=101205 bytes_retransmit=0 bytes_invalid=0 send_seq=5340 receive_seq=5340 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997217 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=160269 bytes_read=4947249 bytes_retransmit=9 bytes_invalid=0 send_seq=22026 receive_seq=22026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997650 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92601 bytes_read=2088160 bytes_retransmit=9 bytes_invalid=0 send_seq=12460 receive_seq=12460 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997443 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=32479 bytes_read=1321465 bytes_retransmit=9 bytes_invalid=0 send_seq=5354 receive_seq=5354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32965 bytes_read=99221 bytes_retransmit=9 bytes_invalid=0 send_seq=5341 receive_seq=5341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87057 bytes_read=2071355 bytes_retransmit=0 bytes_invalid=0 send_seq=9900 receive_seq=9900 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998656 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.8 th2: temp=58.7 th3: temp=56.4 sysload=0.58 cputime=368.793 memavail=7393688 print_time=5205.137 buffer_time=2.330 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 28 Hz
Stats 5181.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=23054907 bytes_read=3605609 bytes_retransmit=9 bytes_invalid=0 send_seq=434085 receive_seq=434085 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=44 upcoming_bytes=5404 freq=400015875 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32218 bytes_read=101221 bytes_retransmit=0 bytes_invalid=0 send_seq=5341 receive_seq=5341 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997238 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=160345 bytes_read=4950335 bytes_retransmit=9 bytes_invalid=0 send_seq=22037 receive_seq=22037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997743 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92607 bytes_read=2088288 bytes_retransmit=9 bytes_invalid=0 send_seq=12461 receive_seq=12461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997489 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=32485 bytes_read=1321729 bytes_retransmit=9 bytes_invalid=0 send_seq=5355 receive_seq=5355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32971 bytes_read=99237 bytes_retransmit=9 bytes_invalid=0 send_seq=5342 receive_seq=5342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87063 bytes_read=2071711 bytes_retransmit=0 bytes_invalid=0 send_seq=9901 receive_seq=9901 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998664 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.4 th1: temp=53.2 th2: temp=58.7 th3: temp=56.5 sysload=0.58 cputime=368.893 memavail=7393688 print_time=5206.012 buffer_time=2.204 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 29 Hz
Stats 5182.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=23062088 bytes_read=3606569 bytes_retransmit=9 bytes_invalid=0 send_seq=434215 receive_seq=434215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=4930 freq=400015889 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32224 bytes_read=101237 bytes_retransmit=0 bytes_invalid=0 send_seq=5342 receive_seq=5342 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997247 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=160421 bytes_read=4953392 bytes_retransmit=9 bytes_invalid=0 send_seq=22048 receive_seq=22048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997712 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92613 bytes_read=2088402 bytes_retransmit=9 bytes_invalid=0 send_seq=12462 receive_seq=12462 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997525 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=32491 bytes_read=1321993 bytes_retransmit=9 bytes_invalid=0 send_seq=5356 receive_seq=5356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32977 bytes_read=99264 bytes_retransmit=9 bytes_invalid=0 send_seq=5343 receive_seq=5343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87069 bytes_read=2072067 bytes_retransmit=0 bytes_invalid=0 send_seq=9902 receive_seq=9902 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998666 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.3 th1: temp=52.6 th2: temp=58.7 th3: temp=56.2 sysload=0.58 cputime=368.999 memavail=7393688 print_time=5206.938 buffer_time=2.130 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 30 Hz
Stats 5183.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=23069571 bytes_read=3607559 bytes_retransmit=9 bytes_invalid=0 send_seq=434351 receive_seq=434351 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=3946 freq=400015895 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32230 bytes_read=101253 bytes_retransmit=0 bytes_invalid=0 send_seq=5343 receive_seq=5343 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997246 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=160497 bytes_read=4956466 bytes_retransmit=9 bytes_invalid=0 send_seq=22059 receive_seq=22059 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997647 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92619 bytes_read=2088502 bytes_retransmit=9 bytes_invalid=0 send_seq=12463 receive_seq=12463 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32497 bytes_read=1322242 bytes_retransmit=9 bytes_invalid=0 send_seq=5357 receive_seq=5357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997612 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32983 bytes_read=99280 bytes_retransmit=9 bytes_invalid=0 send_seq=5344 receive_seq=5344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87075 bytes_read=2072423 bytes_retransmit=0 bytes_invalid=0 send_seq=9903 receive_seq=9903 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998651 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.3 th1: temp=53.0 th2: temp=58.6 th3: temp=56.2 sysload=0.58 cputime=369.101 memavail=7393712 print_time=5207.818 buffer_time=2.010 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 31 Hz
Stats 5184.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=23075907 bytes_read=3608483 bytes_retransmit=9 bytes_invalid=0 send_seq=434468 receive_seq=434468 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=6266 freq=400015904 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=32236 bytes_read=101282 bytes_retransmit=0 bytes_invalid=0 send_seq=5344 receive_seq=5344 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997235 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=160573 bytes_read=4959550 bytes_retransmit=9 bytes_invalid=0 send_seq=22070 receive_seq=22070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997766 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92625 bytes_read=2088630 bytes_retransmit=9 bytes_invalid=0 send_seq=12464 receive_seq=12464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997464 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32503 bytes_read=1322521 bytes_retransmit=9 bytes_invalid=0 send_seq=5358 receive_seq=5358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997602 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32989 bytes_read=99296 bytes_retransmit=9 bytes_invalid=0 send_seq=5345 receive_seq=5345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87081 bytes_read=2072779 bytes_retransmit=0 bytes_invalid=0 send_seq=9904 receive_seq=9904 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998638 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.2 th1: temp=53.0 th2: temp=58.8 th3: temp=56.3 sysload=0.58 cputime=369.210 memavail=7393712 print_time=5209.020 buffer_time=2.211 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 32 Hz
Stats 5185.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=23083472 bytes_read=3609448 bytes_retransmit=9 bytes_invalid=0 send_seq=434600 receive_seq=434600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=5983 freq=400015912 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=32242 bytes_read=101298 bytes_retransmit=0 bytes_invalid=0 send_seq=5345 receive_seq=5345 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997231 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=160642 bytes_read=4962586 bytes_retransmit=9 bytes_invalid=0 send_seq=22080 receive_seq=22080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997682 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92631 bytes_read=2088730 bytes_retransmit=9 bytes_invalid=0 send_seq=12465 receive_seq=12465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997448 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32509 bytes_read=1322770 bytes_retransmit=9 bytes_invalid=0 send_seq=5359 receive_seq=5359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997604 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=32995 bytes_read=99312 bytes_retransmit=9 bytes_invalid=0 send_seq=5346 receive_seq=5346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87087 bytes_read=2073135 bytes_retransmit=0 bytes_invalid=0 send_seq=9905 receive_seq=9905 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998651 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.7 th2: temp=58.5 th3: temp=56.3 sysload=0.54 cputime=369.322 memavail=7394580 print_time=5209.961 buffer_time=2.150 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 33 Hz
Stats 5186.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23091435 bytes_read=3610488 bytes_retransmit=9 bytes_invalid=0 send_seq=434743 receive_seq=434743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=4662 freq=400015904 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=32248 bytes_read=101314 bytes_retransmit=0 bytes_invalid=0 send_seq=5346 receive_seq=5346 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997209 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=160718 bytes_read=4965701 bytes_retransmit=9 bytes_invalid=0 send_seq=22091 receive_seq=22091 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997718 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92637 bytes_read=2088830 bytes_retransmit=9 bytes_invalid=0 send_seq=12466 receive_seq=12466 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997606 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32515 bytes_read=1323004 bytes_retransmit=9 bytes_invalid=0 send_seq=5360 receive_seq=5360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997593 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33001 bytes_read=99328 bytes_retransmit=9 bytes_invalid=0 send_seq=5347 receive_seq=5347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87093 bytes_read=2073491 bytes_retransmit=0 bytes_invalid=0 send_seq=9906 receive_seq=9906 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998640 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.2 th1: temp=52.8 th2: temp=58.5 th3: temp=56.3 sysload=0.54 cputime=369.429 memavail=7394584 print_time=5210.859 buffer_time=2.047 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 34 Hz
Stats 5187.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23098249 bytes_read=3611447 bytes_retransmit=9 bytes_invalid=0 send_seq=434867 receive_seq=434867 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=7095 freq=400015909 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=32254 bytes_read=101330 bytes_retransmit=0 bytes_invalid=0 send_seq=5347 receive_seq=5347 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997227 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=160794 bytes_read=4968788 bytes_retransmit=9 bytes_invalid=0 send_seq=22102 receive_seq=22102 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997685 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92643 bytes_read=2088972 bytes_retransmit=9 bytes_invalid=0 send_seq=12467 receive_seq=12467 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997606 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32521 bytes_read=1323298 bytes_retransmit=9 bytes_invalid=0 send_seq=5361 receive_seq=5361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997604 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33007 bytes_read=99355 bytes_retransmit=9 bytes_invalid=0 send_seq=5348 receive_seq=5348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87099 bytes_read=2073847 bytes_retransmit=0 bytes_invalid=0 send_seq=9907 receive_seq=9907 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998653 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=53.3 th1: temp=53.0 th2: temp=58.7 th3: temp=56.1 sysload=0.54 cputime=369.541 memavail=7394588 print_time=5212.078 buffer_time=2.259 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 35 Hz
Stats 5188.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23106048 bytes_read=3612467 bytes_retransmit=9 bytes_invalid=0 send_seq=435009 receive_seq=435009 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=7440 freq=400015903 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=32260 bytes_read=101346 bytes_retransmit=0 bytes_invalid=0 send_seq=5348 receive_seq=5348 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997241 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=160870 bytes_read=4971861 bytes_retransmit=9 bytes_invalid=0 send_seq=22113 receive_seq=22113 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997641 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92649 bytes_read=2089072 bytes_retransmit=9 bytes_invalid=0 send_seq=12468 receive_seq=12468 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997556 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=32527 bytes_read=1323547 bytes_retransmit=9 bytes_invalid=0 send_seq=5362 receive_seq=5362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997609 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33013 bytes_read=99371 bytes_retransmit=9 bytes_invalid=0 send_seq=5349 receive_seq=5349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87105 bytes_read=2074203 bytes_retransmit=0 bytes_invalid=0 send_seq=9908 receive_seq=9908 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998660 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=53.3 th1: temp=53.0 th2: temp=58.5 th3: temp=56.2 sysload=0.54 cputime=369.645 memavail=7394588 print_time=5213.008 buffer_time=2.188 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 36 Hz
Stats 5189.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23114461 bytes_read=3613532 bytes_retransmit=9 bytes_invalid=0 send_seq=435160 receive_seq=435160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=5656 freq=400015902 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=32266 bytes_read=101375 bytes_retransmit=0 bytes_invalid=0 send_seq=5349 receive_seq=5349 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997251 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=160946 bytes_read=4974918 bytes_retransmit=9 bytes_invalid=0 send_seq=22124 receive_seq=22124 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997618 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92655 bytes_read=2089172 bytes_retransmit=9 bytes_invalid=0 send_seq=12469 receive_seq=12469 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997537 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=32533 bytes_read=1323781 bytes_retransmit=9 bytes_invalid=0 send_seq=5363 receive_seq=5363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997623 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33019 bytes_read=99387 bytes_retransmit=9 bytes_invalid=0 send_seq=5350 receive_seq=5350 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87111 bytes_read=2074559 bytes_retransmit=0 bytes_invalid=0 send_seq=9909 receive_seq=9909 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998656 coil_temp=16.9 refs=0 mcu_temp=20.25 supply_voltage=3.012 th0: temp=52.9 th1: temp=52.9 th2: temp=58.5 th3: temp=56.2 sysload=0.54 cputime=369.751 memavail=7394588 print_time=5213.886 buffer_time=2.065 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5190.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23121580 bytes_read=3614542 bytes_retransmit=9 bytes_invalid=0 send_seq=435292 receive_seq=435292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=7044 freq=400015891 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=32278 bytes_read=101407 bytes_retransmit=0 bytes_invalid=0 send_seq=5351 receive_seq=5351 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997259 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=161028 bytes_read=4978018 bytes_retransmit=9 bytes_invalid=0 send_seq=22136 receive_seq=22136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997727 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92667 bytes_read=2089316 bytes_retransmit=9 bytes_invalid=0 send_seq=12471 receive_seq=12471 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997512 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=32545 bytes_read=1324091 bytes_retransmit=9 bytes_invalid=0 send_seq=5365 receive_seq=5365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33031 bytes_read=99419 bytes_retransmit=9 bytes_invalid=0 send_seq=5352 receive_seq=5352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87123 bytes_read=2074931 bytes_retransmit=0 bytes_invalid=0 send_seq=9911 receive_seq=9911 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998656 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=53.1 th1: temp=52.8 th2: temp=58.3 th3: temp=56.3 sysload=0.49 cputime=369.857 memavail=7394588 print_time=5214.838 buffer_time=2.017 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 37 Hz
Testing frequency 38 Hz
Stats 5191.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23130059 bytes_read=3615618 bytes_retransmit=9 bytes_invalid=0 send_seq=435442 receive_seq=435442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=8541 freq=400015903 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=32284 bytes_read=101423 bytes_retransmit=0 bytes_invalid=0 send_seq=5352 receive_seq=5352 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997299 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=161104 bytes_read=4981133 bytes_retransmit=9 bytes_invalid=0 send_seq=22147 receive_seq=22147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000242 adj=63997704 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92673 bytes_read=2089416 bytes_retransmit=9 bytes_invalid=0 send_seq=12472 receive_seq=12472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=32551 bytes_read=1324325 bytes_retransmit=9 bytes_invalid=0 send_seq=5366 receive_seq=5366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33037 bytes_read=99435 bytes_retransmit=9 bytes_invalid=0 send_seq=5353 receive_seq=5353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87129 bytes_read=2075287 bytes_retransmit=0 bytes_invalid=0 send_seq=9912 receive_seq=9912 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998660 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=53.1 th1: temp=53.0 th2: temp=58.4 th3: temp=56.3 sysload=0.49 cputime=369.974 memavail=7394588 print_time=5216.022 buffer_time=2.201 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 39 Hz
Stats 5192.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23138933 bytes_read=3616713 bytes_retransmit=9 bytes_invalid=0 send_seq=435599 receive_seq=435599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=6531 freq=400015912 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=32290 bytes_read=101439 bytes_retransmit=0 bytes_invalid=0 send_seq=5353 receive_seq=5353 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997256 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=161180 bytes_read=4984191 bytes_retransmit=9 bytes_invalid=0 send_seq=22158 receive_seq=22158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997825 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92679 bytes_read=2089530 bytes_retransmit=9 bytes_invalid=0 send_seq=12473 receive_seq=12473 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=32557 bytes_read=1324559 bytes_retransmit=9 bytes_invalid=0 send_seq=5367 receive_seq=5367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997621 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33043 bytes_read=99462 bytes_retransmit=9 bytes_invalid=0 send_seq=5354 receive_seq=5354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87135 bytes_read=2075633 bytes_retransmit=0 bytes_invalid=0 send_seq=9913 receive_seq=9913 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998666 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=53.2 th1: temp=53.1 th2: temp=58.4 th3: temp=56.2 sysload=0.49 cputime=370.085 memavail=7394588 print_time=5216.909 buffer_time=2.087 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 40 Hz
Stats 5193.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23146500 bytes_read=3617737 bytes_retransmit=9 bytes_invalid=0 send_seq=435736 receive_seq=435736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=7767 freq=400015928 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=32296 bytes_read=101455 bytes_retransmit=0 bytes_invalid=0 send_seq=5354 receive_seq=5354 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997238 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=161256 bytes_read=4987293 bytes_retransmit=9 bytes_invalid=0 send_seq=22169 receive_seq=22169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997766 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92685 bytes_read=2089658 bytes_retransmit=9 bytes_invalid=0 send_seq=12474 receive_seq=12474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997441 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32563 bytes_read=1324868 bytes_retransmit=9 bytes_invalid=0 send_seq=5368 receive_seq=5368 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997604 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33049 bytes_read=99478 bytes_retransmit=9 bytes_invalid=0 send_seq=5355 receive_seq=5355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87141 bytes_read=2075978 bytes_retransmit=0 bytes_invalid=0 send_seq=9914 receive_seq=9914 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998652 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=53.3 th1: temp=53.1 th2: temp=58.5 th3: temp=56.1 sysload=0.49 cputime=370.193 memavail=7394588 print_time=5217.863 buffer_time=2.041 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 41 Hz
Stats 5194.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23155340 bytes_read=3618832 bytes_retransmit=9 bytes_invalid=0 send_seq=435893 receive_seq=435893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=9687 freq=400015929 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32302 bytes_read=101484 bytes_retransmit=0 bytes_invalid=0 send_seq=5355 receive_seq=5355 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997218 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=161332 bytes_read=4990350 bytes_retransmit=9 bytes_invalid=0 send_seq=22180 receive_seq=22180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000242 adj=63997674 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92691 bytes_read=2089758 bytes_retransmit=9 bytes_invalid=0 send_seq=12475 receive_seq=12475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997418 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32569 bytes_read=1325102 bytes_retransmit=9 bytes_invalid=0 send_seq=5369 receive_seq=5369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997585 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33055 bytes_read=99494 bytes_retransmit=9 bytes_invalid=0 send_seq=5356 receive_seq=5356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87147 bytes_read=2076323 bytes_retransmit=0 bytes_invalid=0 send_seq=9915 receive_seq=9915 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998629 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=53.3 th1: temp=53.0 th2: temp=58.3 th3: temp=56.2 sysload=0.49 cputime=370.309 memavail=7394588 print_time=5219.070 buffer_time=2.246 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 42 Hz
Stats 5195.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23164452 bytes_read=3619952 bytes_retransmit=9 bytes_invalid=0 send_seq=436055 receive_seq=436055 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=7804 freq=400015933 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32308 bytes_read=101500 bytes_retransmit=0 bytes_invalid=0 send_seq=5356 receive_seq=5356 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997228 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=161408 bytes_read=4993406 bytes_retransmit=9 bytes_invalid=0 send_seq=22191 receive_seq=22191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997738 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92697 bytes_read=2089858 bytes_retransmit=9 bytes_invalid=0 send_seq=12476 receive_seq=12476 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997422 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32575 bytes_read=1325336 bytes_retransmit=9 bytes_invalid=0 send_seq=5370 receive_seq=5370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997596 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33061 bytes_read=99510 bytes_retransmit=9 bytes_invalid=0 send_seq=5357 receive_seq=5357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999429 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87153 bytes_read=2076668 bytes_retransmit=0 bytes_invalid=0 send_seq=9916 receive_seq=9916 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998640 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=53.2 th1: temp=53.1 th2: temp=58.2 th3: temp=56.1 sysload=0.45 cputime=370.419 memavail=7394588 print_time=5219.952 buffer_time=2.128 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 43 Hz
Stats 5196.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23172630 bytes_read=3621037 bytes_retransmit=9 bytes_invalid=0 send_seq=436202 receive_seq=436202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=8997 freq=400015954 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32314 bytes_read=101516 bytes_retransmit=0 bytes_invalid=0 send_seq=5357 receive_seq=5357 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997233 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=161484 bytes_read=4996490 bytes_retransmit=9 bytes_invalid=0 send_seq=22202 receive_seq=22202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997682 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92703 bytes_read=2089986 bytes_retransmit=9 bytes_invalid=0 send_seq=12477 receive_seq=12477 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997431 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32581 bytes_read=1325630 bytes_retransmit=9 bytes_invalid=0 send_seq=5371 receive_seq=5371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997593 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33067 bytes_read=99526 bytes_retransmit=9 bytes_invalid=0 send_seq=5358 receive_seq=5358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87159 bytes_read=2077013 bytes_retransmit=0 bytes_invalid=0 send_seq=9917 receive_seq=9917 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998638 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=53.3 th1: temp=52.9 th2: temp=58.3 th3: temp=56.0 sysload=0.45 cputime=370.528 memavail=7394604 print_time=5220.868 buffer_time=2.043 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 44 Hz
Stats 5197.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23181957 bytes_read=3622182 bytes_retransmit=9 bytes_invalid=0 send_seq=436369 receive_seq=436369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=10565 freq=400015965 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32320 bytes_read=101532 bytes_retransmit=0 bytes_invalid=0 send_seq=5358 receive_seq=5358 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997216 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=161560 bytes_read=4999547 bytes_retransmit=9 bytes_invalid=0 send_seq=22213 receive_seq=22213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997594 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92709 bytes_read=2090100 bytes_retransmit=9 bytes_invalid=0 send_seq=12478 receive_seq=12478 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997395 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32587 bytes_read=1325864 bytes_retransmit=9 bytes_invalid=0 send_seq=5372 receive_seq=5372 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997581 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33073 bytes_read=99553 bytes_retransmit=9 bytes_invalid=0 send_seq=5359 receive_seq=5359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87165 bytes_read=2077358 bytes_retransmit=0 bytes_invalid=0 send_seq=9918 receive_seq=9918 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998620 coil_temp=17.0 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=53.2 th1: temp=53.0 th2: temp=58.2 th3: temp=56.1 sysload=0.45 cputime=370.654 memavail=7393604 print_time=5222.083 buffer_time=2.258 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 45 Hz
Stats 5198.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23191952 bytes_read=3623382 bytes_retransmit=9 bytes_invalid=0 send_seq=436547 receive_seq=436547 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=8174 freq=400015973 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32326 bytes_read=101548 bytes_retransmit=0 bytes_invalid=0 send_seq=5359 receive_seq=5359 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997207 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=161636 bytes_read=5002622 bytes_retransmit=9 bytes_invalid=0 send_seq=22224 receive_seq=22224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997568 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92715 bytes_read=2090200 bytes_retransmit=9 bytes_invalid=0 send_seq=12479 receive_seq=12479 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997390 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=32593 bytes_read=1326113 bytes_retransmit=9 bytes_invalid=0 send_seq=5373 receive_seq=5373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997589 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33079 bytes_read=99569 bytes_retransmit=9 bytes_invalid=0 send_seq=5360 receive_seq=5360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87171 bytes_read=2077703 bytes_retransmit=0 bytes_invalid=0 send_seq=9919 receive_seq=9919 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998616 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=53.2 th1: temp=52.8 th2: temp=58.4 th3: temp=56.1 sysload=0.45 cputime=370.771 memavail=7393604 print_time=5222.967 buffer_time=2.142 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 46 Hz
Stats 5199.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23200096 bytes_read=3624456 bytes_retransmit=9 bytes_invalid=0 send_seq=436694 receive_seq=436694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=9667 freq=400015977 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32332 bytes_read=101577 bytes_retransmit=0 bytes_invalid=0 send_seq=5360 receive_seq=5360 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997199 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=161712 bytes_read=5005767 bytes_retransmit=9 bytes_invalid=0 send_seq=22235 receive_seq=22235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997524 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92721 bytes_read=2090328 bytes_retransmit=9 bytes_invalid=0 send_seq=12480 receive_seq=12480 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997394 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=32599 bytes_read=1326407 bytes_retransmit=9 bytes_invalid=0 send_seq=5374 receive_seq=5374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997578 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33085 bytes_read=99585 bytes_retransmit=9 bytes_invalid=0 send_seq=5361 receive_seq=5361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999426 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87177 bytes_read=2078048 bytes_retransmit=0 bytes_invalid=0 send_seq=9920 receive_seq=9920 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998609 coil_temp=17.0 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=53.4 th1: temp=53.2 th2: temp=58.3 th3: temp=56.0 sysload=0.45 cputime=370.885 memavail=7393604 print_time=5223.889 buffer_time=2.063 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 47 Hz
Stats 5200.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23209812 bytes_read=3625626 bytes_retransmit=9 bytes_invalid=0 send_seq=436866 receive_seq=436866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=11024 freq=400015979 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32338 bytes_read=101593 bytes_retransmit=0 bytes_invalid=0 send_seq=5361 receive_seq=5361 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997203 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=161788 bytes_read=5008823 bytes_retransmit=9 bytes_invalid=0 send_seq=22246 receive_seq=22246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997519 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92727 bytes_read=2090428 bytes_retransmit=9 bytes_invalid=0 send_seq=12481 receive_seq=12481 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997398 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=32605 bytes_read=1326641 bytes_retransmit=9 bytes_invalid=0 send_seq=5375 receive_seq=5375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997577 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33091 bytes_read=99601 bytes_retransmit=9 bytes_invalid=0 send_seq=5362 receive_seq=5362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999425 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87183 bytes_read=2078399 bytes_retransmit=0 bytes_invalid=0 send_seq=9921 receive_seq=9921 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998609 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=53.3 th1: temp=53.2 th2: temp=58.5 th3: temp=55.8 sysload=0.50 cputime=371.009 memavail=7393624 print_time=5225.100 buffer_time=2.273 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 48 Hz
Stats 5201.2: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23219947 bytes_read=3626842 bytes_retransmit=9 bytes_invalid=0 send_seq=437044 receive_seq=437044 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=8579 freq=400015978 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32344 bytes_read=101609 bytes_retransmit=0 bytes_invalid=0 send_seq=5362 receive_seq=5362 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997215 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=161857 bytes_read=5011859 bytes_retransmit=9 bytes_invalid=0 send_seq=22256 receive_seq=22256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997525 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92733 bytes_read=2090528 bytes_retransmit=9 bytes_invalid=0 send_seq=12482 receive_seq=12482 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000072 adj=63997526 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=32611 bytes_read=1326875 bytes_retransmit=9 bytes_invalid=0 send_seq=5376 receive_seq=5376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997618 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33097 bytes_read=99617 bytes_retransmit=9 bytes_invalid=0 send_seq=5363 receive_seq=5363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87189 bytes_read=2078755 bytes_retransmit=0 bytes_invalid=0 send_seq=9922 receive_seq=9922 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998649 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=53.4 th1: temp=53.2 th2: temp=58.4 th3: temp=56.1 sysload=0.50 cputime=371.137 memavail=7392792 print_time=5225.986 buffer_time=2.159 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 49 Hz
Stats 5202.2: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23228421 bytes_read=3627941 bytes_retransmit=9 bytes_invalid=0 send_seq=437196 receive_seq=437196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=10076 freq=400015981 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32350 bytes_read=101625 bytes_retransmit=0 bytes_invalid=0 send_seq=5363 receive_seq=5363 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997228 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=161933 bytes_read=5014944 bytes_retransmit=9 bytes_invalid=0 send_seq=22267 receive_seq=22267 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000243 adj=63997509 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92739 bytes_read=2090670 bytes_retransmit=9 bytes_invalid=0 send_seq=12483 receive_seq=12483 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997657 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=32617 bytes_read=1327169 bytes_retransmit=9 bytes_invalid=0 send_seq=5377 receive_seq=5377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33103 bytes_read=99644 bytes_retransmit=9 bytes_invalid=0 send_seq=5364 receive_seq=5364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87195 bytes_read=2079111 bytes_retransmit=0 bytes_invalid=0 send_seq=9923 receive_seq=9923 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998644 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=53.5 th1: temp=53.1 th2: temp=58.2 th3: temp=56.0 sysload=0.50 cputime=371.262 memavail=7393244 print_time=5226.906 buffer_time=2.079 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 50 Hz
Stats 5203.2: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23238102 bytes_read=3629101 bytes_retransmit=9 bytes_invalid=0 send_seq=437366 receive_seq=437366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=11997 freq=400015973 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32356 bytes_read=101641 bytes_retransmit=0 bytes_invalid=0 send_seq=5364 receive_seq=5364 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997230 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=162009 bytes_read=5018017 bytes_retransmit=9 bytes_invalid=0 send_seq=22278 receive_seq=22278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000239 adj=63997798 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92745 bytes_read=2090770 bytes_retransmit=9 bytes_invalid=0 send_seq=12484 receive_seq=12484 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997609 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32623 bytes_read=1327418 bytes_retransmit=9 bytes_invalid=0 send_seq=5378 receive_seq=5378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997623 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33109 bytes_read=99660 bytes_retransmit=9 bytes_invalid=0 send_seq=5365 receive_seq=5365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87201 bytes_read=2079467 bytes_retransmit=0 bytes_invalid=0 send_seq=9924 receive_seq=9924 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998634 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=53.3 th1: temp=53.2 th2: temp=58.3 th3: temp=56.1 sysload=0.50 cputime=371.389 memavail=7393244 print_time=5228.110 buffer_time=2.282 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 51 Hz
Stats 5204.2: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23248551 bytes_read=3630336 bytes_retransmit=9 bytes_invalid=0 send_seq=437551 receive_seq=437551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=9414 freq=400015969 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32362 bytes_read=101670 bytes_retransmit=0 bytes_invalid=0 send_seq=5365 receive_seq=5365 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997244 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=162085 bytes_read=5021075 bytes_retransmit=9 bytes_invalid=0 send_seq=22289 receive_seq=22289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997731 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92751 bytes_read=2090870 bytes_retransmit=9 bytes_invalid=0 send_seq=12485 receive_seq=12485 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997581 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32629 bytes_read=1327652 bytes_retransmit=9 bytes_invalid=0 send_seq=5379 receive_seq=5379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997634 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33115 bytes_read=99676 bytes_retransmit=9 bytes_invalid=0 send_seq=5366 receive_seq=5366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87207 bytes_read=2079823 bytes_retransmit=0 bytes_invalid=0 send_seq=9925 receive_seq=9925 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998656 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=53.4 th1: temp=53.1 th2: temp=58.4 th3: temp=56.1 sysload=0.50 cputime=371.508 memavail=7393244 print_time=5228.997 buffer_time=2.169 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 52 Hz
Stats 5205.2: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23257535 bytes_read=3631475 bytes_retransmit=9 bytes_invalid=0 send_seq=437711 receive_seq=437711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=10589 freq=400015963 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32368 bytes_read=101686 bytes_retransmit=0 bytes_invalid=0 send_seq=5366 receive_seq=5366 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997251 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=162161 bytes_read=5024160 bytes_retransmit=9 bytes_invalid=0 send_seq=22300 receive_seq=22300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997684 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92757 bytes_read=2090998 bytes_retransmit=9 bytes_invalid=0 send_seq=12486 receive_seq=12486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000077 adj=63997576 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32635 bytes_read=1327946 bytes_retransmit=9 bytes_invalid=0 send_seq=5380 receive_seq=5380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33121 bytes_read=99692 bytes_retransmit=9 bytes_invalid=0 send_seq=5367 receive_seq=5367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87213 bytes_read=2080179 bytes_retransmit=0 bytes_invalid=0 send_seq=9926 receive_seq=9926 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998653 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=53.3 th1: temp=53.1 th2: temp=58.3 th3: temp=56.0 sysload=0.46 cputime=371.622 memavail=7393244 print_time=5229.913 buffer_time=2.084 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 53 Hz
Stats 5206.2: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23267582 bytes_read=3632666 bytes_retransmit=9 bytes_invalid=0 send_seq=437884 receive_seq=437884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=12489 freq=400015970 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32374 bytes_read=101702 bytes_retransmit=0 bytes_invalid=0 send_seq=5367 receive_seq=5367 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997258 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=162237 bytes_read=5027276 bytes_retransmit=9 bytes_invalid=0 send_seq=22311 receive_seq=22311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997646 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92763 bytes_read=2091098 bytes_retransmit=9 bytes_invalid=0 send_seq=12487 receive_seq=12487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000075 adj=63997686 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32641 bytes_read=1328180 bytes_retransmit=9 bytes_invalid=0 send_seq=5381 receive_seq=5381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33127 bytes_read=99708 bytes_retransmit=9 bytes_invalid=0 send_seq=5368 receive_seq=5368 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87219 bytes_read=2080535 bytes_retransmit=0 bytes_invalid=0 send_seq=9927 receive_seq=9927 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998657 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=53.1 th1: temp=53.1 th2: temp=58.4 th3: temp=55.9 sysload=0.46 cputime=371.750 memavail=7392748 print_time=5231.109 buffer_time=2.275 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 54 Hz
Stats 5207.2: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23278291 bytes_read=3633916 bytes_retransmit=9 bytes_invalid=0 send_seq=438073 receive_seq=438073 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=10092 freq=400015967 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32380 bytes_read=101718 bytes_retransmit=0 bytes_invalid=0 send_seq=5368 receive_seq=5368 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997251 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=162313 bytes_read=5030334 bytes_retransmit=9 bytes_invalid=0 send_seq=22322 receive_seq=22322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997599 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92769 bytes_read=2091212 bytes_retransmit=9 bytes_invalid=0 send_seq=12488 receive_seq=12488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000072 adj=63997596 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32647 bytes_read=1328414 bytes_retransmit=9 bytes_invalid=0 send_seq=5382 receive_seq=5382 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33133 bytes_read=99735 bytes_retransmit=9 bytes_invalid=0 send_seq=5369 receive_seq=5369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999444 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87225 bytes_read=2080891 bytes_retransmit=0 bytes_invalid=0 send_seq=9928 receive_seq=9928 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998645 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=53.2 th1: temp=53.0 th2: temp=58.2 th3: temp=56.0 sysload=0.46 cputime=371.870 memavail=7392284 print_time=5232.021 buffer_time=2.186 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 55 Hz
Stats 5208.2: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23287626 bytes_read=3635080 bytes_retransmit=9 bytes_invalid=0 send_seq=438238 receive_seq=438238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=23 upcoming_bytes=11025 freq=400015968 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32386 bytes_read=101734 bytes_retransmit=0 bytes_invalid=0 send_seq=5369 receive_seq=5369 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997256 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=162389 bytes_read=5033437 bytes_retransmit=9 bytes_invalid=0 send_seq=22333 receive_seq=22333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997579 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92775 bytes_read=2091340 bytes_retransmit=9 bytes_invalid=0 send_seq=12489 receive_seq=12489 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997562 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=32653 bytes_read=1328723 bytes_retransmit=9 bytes_invalid=0 send_seq=5383 receive_seq=5383 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33139 bytes_read=99751 bytes_retransmit=9 bytes_invalid=0 send_seq=5370 receive_seq=5370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999452 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87231 bytes_read=2081247 bytes_retransmit=0 bytes_invalid=0 send_seq=9929 receive_seq=9929 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998650 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=53.2 th1: temp=53.1 th2: temp=58.3 th3: temp=55.8 sysload=0.46 cputime=371.986 memavail=7392284 print_time=5232.923 buffer_time=2.088 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5209.2: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23297911 bytes_read=3636295 bytes_retransmit=9 bytes_invalid=0 send_seq=438419 receive_seq=438419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=9278 freq=400015963 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32392 bytes_read=101763 bytes_retransmit=0 bytes_invalid=0 send_seq=5370 receive_seq=5370 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997261 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=162465 bytes_read=5036493 bytes_retransmit=9 bytes_invalid=0 send_seq=22344 receive_seq=22344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997672 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92781 bytes_read=2091440 bytes_retransmit=9 bytes_invalid=0 send_seq=12490 receive_seq=12490 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=32659 bytes_read=1328957 bytes_retransmit=9 bytes_invalid=0 send_seq=5384 receive_seq=5384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33145 bytes_read=99767 bytes_retransmit=9 bytes_invalid=0 send_seq=5371 receive_seq=5371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87237 bytes_read=2081603 bytes_retransmit=0 bytes_invalid=0 send_seq=9930 receive_seq=9930 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998668 coil_temp=17.0 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=53.3 th1: temp=53.3 th2: temp=58.2 th3: temp=56.0 sysload=0.46 cputime=372.104 memavail=7392288 print_time=5233.841 buffer_time=2.006 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 56 Hz
Testing frequency 57 Hz
Stats 5210.2: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23308749 bytes_read=3637565 bytes_retransmit=9 bytes_invalid=0 send_seq=438611 receive_seq=438611 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=35 upcoming_bytes=10942 freq=400015969 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32398 bytes_read=101779 bytes_retransmit=0 bytes_invalid=0 send_seq=5371 receive_seq=5371 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997268 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=162541 bytes_read=5039550 bytes_retransmit=9 bytes_invalid=0 send_seq=22355 receive_seq=22355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997651 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92787 bytes_read=2091540 bytes_retransmit=9 bytes_invalid=0 send_seq=12491 receive_seq=12491 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997503 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=32665 bytes_read=1329191 bytes_retransmit=9 bytes_invalid=0 send_seq=5385 receive_seq=5385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33151 bytes_read=99783 bytes_retransmit=9 bytes_invalid=0 send_seq=5372 receive_seq=5372 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999451 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87243 bytes_read=2081959 bytes_retransmit=0 bytes_invalid=0 send_seq=9931 receive_seq=9931 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998666 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=53.5 th1: temp=53.3 th2: temp=58.2 th3: temp=56.0 sysload=0.42 cputime=372.235 memavail=7392288 print_time=5235.047 buffer_time=2.212 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 58 Hz
Stats 5211.2: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23318368 bytes_read=3638770 bytes_retransmit=9 bytes_invalid=0 send_seq=438781 receive_seq=438781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=11951 freq=400015958 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32404 bytes_read=101795 bytes_retransmit=0 bytes_invalid=0 send_seq=5372 receive_seq=5372 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997249 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=162617 bytes_read=5042622 bytes_retransmit=9 bytes_invalid=0 send_seq=22366 receive_seq=22366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997602 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92793 bytes_read=2091661 bytes_retransmit=9 bytes_invalid=0 send_seq=12492 receive_seq=12492 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997513 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=32671 bytes_read=1329485 bytes_retransmit=9 bytes_invalid=0 send_seq=5386 receive_seq=5386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997634 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33157 bytes_read=99799 bytes_retransmit=9 bytes_invalid=0 send_seq=5373 receive_seq=5373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87249 bytes_read=2082315 bytes_retransmit=0 bytes_invalid=0 send_seq=9932 receive_seq=9932 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998655 coil_temp=17.0 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=53.3 th1: temp=53.2 th2: temp=58.2 th3: temp=55.9 sysload=0.42 cputime=372.350 memavail=7392288 print_time=5235.936 buffer_time=2.100 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 59 Hz
Stats 5212.2: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23328969 bytes_read=3640010 bytes_retransmit=9 bytes_invalid=0 send_seq=438967 receive_seq=438967 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=10114 freq=400015953 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32410 bytes_read=101811 bytes_retransmit=0 bytes_invalid=0 send_seq=5373 receive_seq=5373 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997280 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=162693 bytes_read=5045720 bytes_retransmit=9 bytes_invalid=0 send_seq=22377 receive_seq=22377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997591 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92799 bytes_read=2091754 bytes_retransmit=9 bytes_invalid=0 send_seq=12493 receive_seq=12493 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=32677 bytes_read=1329719 bytes_retransmit=9 bytes_invalid=0 send_seq=5387 receive_seq=5387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33163 bytes_read=99826 bytes_retransmit=9 bytes_invalid=0 send_seq=5374 receive_seq=5374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999445 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87255 bytes_read=2082671 bytes_retransmit=0 bytes_invalid=0 send_seq=9933 receive_seq=9933 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998686 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=53.2 th1: temp=52.9 th2: temp=58.1 th3: temp=56.0 sysload=0.42 cputime=372.469 memavail=7392312 print_time=5236.858 buffer_time=2.021 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 60 Hz
Stats 5213.2: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23340385 bytes_read=3641310 bytes_retransmit=9 bytes_invalid=0 send_seq=439165 receive_seq=439165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=11498 freq=400015966 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32416 bytes_read=101827 bytes_retransmit=0 bytes_invalid=0 send_seq=5374 receive_seq=5374 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997285 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=162769 bytes_read=5048780 bytes_retransmit=9 bytes_invalid=0 send_seq=22388 receive_seq=22388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997575 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92805 bytes_read=2091861 bytes_retransmit=9 bytes_invalid=0 send_seq=12494 receive_seq=12494 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32683 bytes_read=1329968 bytes_retransmit=9 bytes_invalid=0 send_seq=5388 receive_seq=5388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33169 bytes_read=99842 bytes_retransmit=9 bytes_invalid=0 send_seq=5375 receive_seq=5375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87261 bytes_read=2083027 bytes_retransmit=0 bytes_invalid=0 send_seq=9934 receive_seq=9934 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998681 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=53.3 th1: temp=53.4 th2: temp=58.2 th3: temp=56.0 sysload=0.42 cputime=372.601 memavail=7392312 print_time=5238.066 buffer_time=2.228 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 61 Hz
Stats 5214.2: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23350116 bytes_read=3642504 bytes_retransmit=9 bytes_invalid=0 send_seq=439336 receive_seq=439336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=12466 freq=400015965 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32422 bytes_read=101856 bytes_retransmit=0 bytes_invalid=0 send_seq=5375 receive_seq=5375 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997269 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=162845 bytes_read=5051846 bytes_retransmit=9 bytes_invalid=0 send_seq=22399 receive_seq=22399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997543 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92811 bytes_read=2091980 bytes_retransmit=9 bytes_invalid=0 send_seq=12495 receive_seq=12495 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000082 adj=63997454 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32689 bytes_read=1330262 bytes_retransmit=9 bytes_invalid=0 send_seq=5389 receive_seq=5389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33175 bytes_read=99858 bytes_retransmit=9 bytes_invalid=0 send_seq=5376 receive_seq=5376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87267 bytes_read=2083383 bytes_retransmit=0 bytes_invalid=0 send_seq=9935 receive_seq=9935 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998657 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=53.3 th1: temp=53.1 th2: temp=58.1 th3: temp=56.0 sysload=0.42 cputime=372.718 memavail=7392312 print_time=5238.956 buffer_time=2.118 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 62 Hz
Stats 5215.2: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23361005 bytes_read=3643774 bytes_retransmit=9 bytes_invalid=0 send_seq=439528 receive_seq=439528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=44 upcoming_bytes=10696 freq=400015967 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32428 bytes_read=101872 bytes_retransmit=0 bytes_invalid=0 send_seq=5376 receive_seq=5376 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997264 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=162921 bytes_read=5054895 bytes_retransmit=9 bytes_invalid=0 send_seq=22410 receive_seq=22410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997525 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92817 bytes_read=2092077 bytes_retransmit=9 bytes_invalid=0 send_seq=12496 receive_seq=12496 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000096 adj=63997694 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32695 bytes_read=1330496 bytes_retransmit=9 bytes_invalid=0 send_seq=5390 receive_seq=5390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33181 bytes_read=99874 bytes_retransmit=9 bytes_invalid=0 send_seq=5377 receive_seq=5377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87273 bytes_read=2083739 bytes_retransmit=0 bytes_invalid=0 send_seq=9936 receive_seq=9936 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998657 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=53.3 th1: temp=53.5 th2: temp=58.3 th3: temp=56.0 sysload=0.39 cputime=372.839 memavail=7392312 print_time=5239.866 buffer_time=2.027 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 63 Hz
Stats 5216.2: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23372635 bytes_read=3645110 bytes_retransmit=9 bytes_invalid=0 send_seq=439730 receive_seq=439730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=12463 freq=400015969 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32434 bytes_read=101888 bytes_retransmit=0 bytes_invalid=0 send_seq=5377 receive_seq=5377 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997254 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=162997 bytes_read=5057952 bytes_retransmit=9 bytes_invalid=0 send_seq=22421 receive_seq=22421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997502 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92823 bytes_read=2092177 bytes_retransmit=9 bytes_invalid=0 send_seq=12497 receive_seq=12497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000100 adj=63997847 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32701 bytes_read=1330730 bytes_retransmit=9 bytes_invalid=0 send_seq=5391 receive_seq=5391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33187 bytes_read=99890 bytes_retransmit=9 bytes_invalid=0 send_seq=5378 receive_seq=5378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87279 bytes_read=2084095 bytes_retransmit=0 bytes_invalid=0 send_seq=9937 receive_seq=9937 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998653 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=53.0 th1: temp=53.3 th2: temp=58.3 th3: temp=55.7 sysload=0.39 cputime=372.974 memavail=7392320 print_time=5241.083 buffer_time=2.244 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 64 Hz
Stats 5217.2: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23382812 bytes_read=3646330 bytes_retransmit=9 bytes_invalid=0 send_seq=439907 receive_seq=439907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=13033 freq=400015956 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32440 bytes_read=101904 bytes_retransmit=0 bytes_invalid=0 send_seq=5378 receive_seq=5378 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997242 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=163073 bytes_read=5061037 bytes_retransmit=9 bytes_invalid=0 send_seq=22432 receive_seq=22432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997518 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92829 bytes_read=2092305 bytes_retransmit=9 bytes_invalid=0 send_seq=12498 receive_seq=12498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000095 adj=63997795 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32707 bytes_read=1331024 bytes_retransmit=9 bytes_invalid=0 send_seq=5392 receive_seq=5392 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33193 bytes_read=99917 bytes_retransmit=9 bytes_invalid=0 send_seq=5379 receive_seq=5379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87285 bytes_read=2084469 bytes_retransmit=0 bytes_invalid=0 send_seq=9938 receive_seq=9938 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998740 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=53.4 th1: temp=53.2 th2: temp=58.3 th3: temp=56.0 sysload=0.39 cputime=373.099 memavail=7392072 print_time=5241.955 buffer_time=2.115 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 65 Hz
Stats 5218.2: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23394006 bytes_read=3647613 bytes_retransmit=9 bytes_invalid=0 send_seq=440102 receive_seq=440102 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=11393 freq=400016095 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32446 bytes_read=101920 bytes_retransmit=0 bytes_invalid=0 send_seq=5379 receive_seq=5379 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997249 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=163149 bytes_read=5064111 bytes_retransmit=9 bytes_invalid=0 send_seq=22443 receive_seq=22443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997643 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92835 bytes_read=2092419 bytes_retransmit=9 bytes_invalid=0 send_seq=12499 receive_seq=12499 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000090 adj=63997733 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32713 bytes_read=1331273 bytes_retransmit=9 bytes_invalid=0 send_seq=5393 receive_seq=5393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33199 bytes_read=99933 bytes_retransmit=9 bytes_invalid=0 send_seq=5380 receive_seq=5380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87291 bytes_read=2084825 bytes_retransmit=0 bytes_invalid=0 send_seq=9939 receive_seq=9939 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998730 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=53.6 th1: temp=53.2 th2: temp=58.1 th3: temp=56.0 sysload=0.39 cputime=373.225 memavail=7392084 print_time=5242.884 buffer_time=2.044 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 66 Hz
Stats 5219.2: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23405878 bytes_read=3648958 bytes_retransmit=9 bytes_invalid=0 send_seq=440309 receive_seq=440309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=13121 freq=400016230 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32452 bytes_read=101949 bytes_retransmit=0 bytes_invalid=0 send_seq=5380 receive_seq=5380 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997023 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=163218 bytes_read=5067144 bytes_retransmit=9 bytes_invalid=0 send_seq=22453 receive_seq=22453 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997328 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92841 bytes_read=2092519 bytes_retransmit=9 bytes_invalid=0 send_seq=12500 receive_seq=12500 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000085 adj=63997356 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32719 bytes_read=1331507 bytes_retransmit=9 bytes_invalid=0 send_seq=5394 receive_seq=5394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997439 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33205 bytes_read=99949 bytes_retransmit=9 bytes_invalid=0 send_seq=5381 receive_seq=5381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999386 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87297 bytes_read=2085181 bytes_retransmit=0 bytes_invalid=0 send_seq=9940 receive_seq=9940 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998568 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=53.3 th1: temp=53.4 th2: temp=58.2 th3: temp=56.0 sysload=0.39 cputime=373.372 memavail=7388812 print_time=5244.089 buffer_time=2.248 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 67 Hz
Stats 5220.2: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23416307 bytes_read=3650212 bytes_retransmit=9 bytes_invalid=0 send_seq=440492 receive_seq=440492 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=13700 freq=400016358 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32458 bytes_read=101965 bytes_retransmit=0 bytes_invalid=0 send_seq=5381 receive_seq=5381 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49996889 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=163294 bytes_read=5070288 bytes_retransmit=9 bytes_invalid=0 send_seq=22464 receive_seq=22464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997163 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92847 bytes_read=2092647 bytes_retransmit=9 bytes_invalid=0 send_seq=12501 receive_seq=12501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000085 adj=63997094 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32725 bytes_read=1331801 bytes_retransmit=9 bytes_invalid=0 send_seq=5395 receive_seq=5395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997393 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33211 bytes_read=99965 bytes_retransmit=9 bytes_invalid=0 send_seq=5382 receive_seq=5382 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999352 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87303 bytes_read=2085537 bytes_retransmit=0 bytes_invalid=0 send_seq=9941 receive_seq=9941 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998460 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=53.5 th1: temp=53.2 th2: temp=58.2 th3: temp=56.0 sysload=0.35 cputime=373.493 memavail=7395188 print_time=5244.972 buffer_time=2.131 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 68 Hz
Stats 5221.2: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23427774 bytes_read=3651538 bytes_retransmit=9 bytes_invalid=0 send_seq=440692 receive_seq=440692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=12314 freq=400016474 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32464 bytes_read=101981 bytes_retransmit=0 bytes_invalid=0 send_seq=5382 receive_seq=5382 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49996728 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=163370 bytes_read=5073345 bytes_retransmit=9 bytes_invalid=0 send_seq=22475 receive_seq=22475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63996933 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92853 bytes_read=2092747 bytes_retransmit=9 bytes_invalid=0 send_seq=12502 receive_seq=12502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000082 adj=63996885 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32731 bytes_read=1332035 bytes_retransmit=9 bytes_invalid=0 send_seq=5396 receive_seq=5396 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997214 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33217 bytes_read=99981 bytes_retransmit=9 bytes_invalid=0 send_seq=5383 receive_seq=5383 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999311 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87309 bytes_read=2085893 bytes_retransmit=0 bytes_invalid=0 send_seq=9942 receive_seq=9942 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998345 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=53.3 th1: temp=53.1 th2: temp=58.2 th3: temp=56.0 sysload=0.35 cputime=373.616 memavail=7394964 print_time=5245.898 buffer_time=2.056 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 69 Hz
Stats 5222.2: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23440058 bytes_read=3652918 bytes_retransmit=9 bytes_invalid=0 send_seq=440906 receive_seq=440906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=14044 freq=400016559 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32470 bytes_read=101997 bytes_retransmit=0 bytes_invalid=0 send_seq=5383 receive_seq=5383 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49996608 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=163446 bytes_read=5076403 bytes_retransmit=9 bytes_invalid=0 send_seq=22486 receive_seq=22486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63996761 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=92859 bytes_read=2092847 bytes_retransmit=9 bytes_invalid=0 send_seq=12503 receive_seq=12503 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000078 adj=63996688 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32737 bytes_read=1332269 bytes_retransmit=9 bytes_invalid=0 send_seq=5397 receive_seq=5397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997080 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33223 bytes_read=100008 bytes_retransmit=9 bytes_invalid=0 send_seq=5384 receive_seq=5384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999288 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87315 bytes_read=2086249 bytes_retransmit=0 bytes_invalid=0 send_seq=9943 receive_seq=9943 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998270 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=53.3 th1: temp=53.2 th2: temp=58.3 th3: temp=55.9 sysload=0.35 cputime=373.751 memavail=7394964 print_time=5247.106 buffer_time=2.264 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 70 Hz
Stats 5223.2: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23450782 bytes_read=3654197 bytes_retransmit=9 bytes_invalid=0 send_seq=441094 receive_seq=441094 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=43 upcoming_bytes=14510 freq=400016654 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32476 bytes_read=102013 bytes_retransmit=0 bytes_invalid=0 send_seq=5384 receive_seq=5384 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49996659 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=163522 bytes_read=5079504 bytes_retransmit=9 bytes_invalid=0 send_seq=22497 receive_seq=22497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63996855 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92865 bytes_read=2092989 bytes_retransmit=9 bytes_invalid=0 send_seq=12504 receive_seq=12504 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000075 adj=63996708 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32743 bytes_read=1332578 bytes_retransmit=9 bytes_invalid=0 send_seq=5398 receive_seq=5398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997140 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33229 bytes_read=100024 bytes_retransmit=9 bytes_invalid=0 send_seq=5385 receive_seq=5385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999297 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87321 bytes_read=2086605 bytes_retransmit=0 bytes_invalid=0 send_seq=9944 receive_seq=9944 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998286 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=53.1 th1: temp=52.7 th2: temp=58.3 th3: temp=55.9 sysload=0.35 cputime=373.873 memavail=7394964 print_time=5247.978 buffer_time=2.136 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 71 Hz
Stats 5224.2: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23462559 bytes_read=3655527 bytes_retransmit=9 bytes_invalid=0 send_seq=441298 receive_seq=441298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=13129 freq=400016749 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32482 bytes_read=102042 bytes_retransmit=0 bytes_invalid=0 send_seq=5385 receive_seq=5385 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49996552 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=163598 bytes_read=5082561 bytes_retransmit=9 bytes_invalid=0 send_seq=22508 receive_seq=22508 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63996725 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92871 bytes_read=2093089 bytes_retransmit=9 bytes_invalid=0 send_seq=12505 receive_seq=12505 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000072 adj=63996557 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32749 bytes_read=1332812 bytes_retransmit=9 bytes_invalid=0 send_seq=5399 receive_seq=5399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997033 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33235 bytes_read=100040 bytes_retransmit=9 bytes_invalid=0 send_seq=5386 receive_seq=5386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999273 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87327 bytes_read=2086961 bytes_retransmit=0 bytes_invalid=0 send_seq=9945 receive_seq=9945 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998214 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=53.3 th1: temp=53.3 th2: temp=58.3 th3: temp=55.8 sysload=0.35 cputime=373.997 memavail=7394964 print_time=5248.909 buffer_time=2.067 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 72 Hz
Stats 5225.2: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23475374 bytes_read=3656952 bytes_retransmit=9 bytes_invalid=0 send_seq=441521 receive_seq=441521 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=14886 freq=400016700 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32488 bytes_read=102058 bytes_retransmit=0 bytes_invalid=0 send_seq=5386 receive_seq=5386 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49996489 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=163674 bytes_read=5085619 bytes_retransmit=9 bytes_invalid=0 send_seq=22519 receive_seq=22519 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63996623 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92877 bytes_read=2093189 bytes_retransmit=9 bytes_invalid=0 send_seq=12506 receive_seq=12506 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63996451 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32755 bytes_read=1333046 bytes_retransmit=9 bytes_invalid=0 send_seq=5400 receive_seq=5400 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47996955 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33241 bytes_read=100056 bytes_retransmit=9 bytes_invalid=0 send_seq=5387 receive_seq=5387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999256 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87333 bytes_read=2087317 bytes_retransmit=0 bytes_invalid=0 send_seq=9946 receive_seq=9946 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998162 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=53.3 th1: temp=53.2 th2: temp=58.2 th3: temp=55.9 sysload=0.33 cputime=374.137 memavail=7394980 print_time=5250.123 buffer_time=2.280 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 73 Hz
Stats 5226.2: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23486347 bytes_read=3658262 bytes_retransmit=9 bytes_invalid=0 send_seq=441712 receive_seq=441712 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=15121 freq=400016649 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32494 bytes_read=102074 bytes_retransmit=0 bytes_invalid=0 send_seq=5387 receive_seq=5387 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49996762 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=163750 bytes_read=5088703 bytes_retransmit=9 bytes_invalid=0 send_seq=22530 receive_seq=22530 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63996985 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92883 bytes_read=2093317 bytes_retransmit=9 bytes_invalid=0 send_seq=12507 receive_seq=12507 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63996808 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32761 bytes_read=1333340 bytes_retransmit=9 bytes_invalid=0 send_seq=5401 receive_seq=5401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997195 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33247 bytes_read=100072 bytes_retransmit=9 bytes_invalid=0 send_seq=5388 receive_seq=5388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999320 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87339 bytes_read=2087673 bytes_retransmit=0 bytes_invalid=0 send_seq=9947 receive_seq=9947 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998331 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=53.4 th1: temp=53.3 th2: temp=58.3 th3: temp=56.1 sysload=0.33 cputime=374.259 memavail=7394988 print_time=5250.996 buffer_time=2.153 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 74 Hz
Stats 5227.2: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23498361 bytes_read=3659617 bytes_retransmit=9 bytes_invalid=0 send_seq=441921 receive_seq=441921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=14396 freq=400016598 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32500 bytes_read=102090 bytes_retransmit=0 bytes_invalid=0 send_seq=5388 receive_seq=5388 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49996878 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=163826 bytes_read=5091759 bytes_retransmit=9 bytes_invalid=0 send_seq=22541 receive_seq=22541 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997232 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92889 bytes_read=2093417 bytes_retransmit=9 bytes_invalid=0 send_seq=12508 receive_seq=12508 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63996925 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32767 bytes_read=1333574 bytes_retransmit=9 bytes_invalid=0 send_seq=5402 receive_seq=5402 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997295 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33253 bytes_read=100099 bytes_retransmit=9 bytes_invalid=0 send_seq=5389 receive_seq=5389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999347 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87345 bytes_read=2088029 bytes_retransmit=0 bytes_invalid=0 send_seq=9948 receive_seq=9948 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998399 coil_temp=17.0 refs=0 mcu_temp=20.34 supply_voltage=3.011 th0: temp=53.3 th1: temp=53.2 th2: temp=58.0 th3: temp=56.0 sysload=0.33 cputime=374.389 memavail=7393520 print_time=5251.933 buffer_time=2.090 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 75 Hz
Stats 5228.2: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23511417 bytes_read=3661043 bytes_retransmit=9 bytes_invalid=0 send_seq=442145 receive_seq=442145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=15848 freq=400016569 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32506 bytes_read=102106 bytes_retransmit=0 bytes_invalid=0 send_seq=5389 receive_seq=5389 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49996999 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=163902 bytes_read=5094891 bytes_retransmit=9 bytes_invalid=0 send_seq=22552 receive_seq=22552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997354 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92895 bytes_read=2093531 bytes_retransmit=9 bytes_invalid=0 send_seq=12509 receive_seq=12509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997062 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32773 bytes_read=1333823 bytes_retransmit=9 bytes_invalid=0 send_seq=5403 receive_seq=5403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997404 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33259 bytes_read=100115 bytes_retransmit=9 bytes_invalid=0 send_seq=5390 receive_seq=5390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999375 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87351 bytes_read=2088385 bytes_retransmit=0 bytes_invalid=0 send_seq=9949 receive_seq=9949 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998472 coil_temp=17.0 refs=0 mcu_temp=20.34 supply_voltage=3.011 th0: temp=53.4 th1: temp=53.4 th2: temp=58.3 th3: temp=56.0 sysload=0.33 cputime=374.534 memavail=7393520 print_time=5253.128 buffer_time=2.285 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 76 Hz
Stats 5229.2: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23522753 bytes_read=3662372 bytes_retransmit=9 bytes_invalid=0 send_seq=442343 receive_seq=442343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=15840 freq=400016508 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=32512 bytes_read=102135 bytes_retransmit=0 bytes_invalid=0 send_seq=5390 receive_seq=5390 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997097 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=163978 bytes_read=5097975 bytes_retransmit=9 bytes_invalid=0 send_seq=22563 receive_seq=22563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997449 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92901 bytes_read=2093659 bytes_retransmit=9 bytes_invalid=0 send_seq=12510 receive_seq=12510 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997181 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32779 bytes_read=1334117 bytes_retransmit=9 bytes_invalid=0 send_seq=5404 receive_seq=5404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997489 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33265 bytes_read=100131 bytes_retransmit=9 bytes_invalid=0 send_seq=5391 receive_seq=5391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999407 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87357 bytes_read=2088741 bytes_retransmit=0 bytes_invalid=0 send_seq=9950 receive_seq=9950 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998537 coil_temp=17.0 refs=0 mcu_temp=20.34 supply_voltage=3.011 th0: temp=53.1 th1: temp=53.3 th2: temp=58.3 th3: temp=56.0 sysload=0.33 cputime=374.660 memavail=7393520 print_time=5254.003 buffer_time=2.160 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 77 Hz
Stats 5230.2: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23535112 bytes_read=3663757 bytes_retransmit=9 bytes_invalid=0 send_seq=442558 receive_seq=442558 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=15006 freq=400016469 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=32518 bytes_read=102151 bytes_retransmit=0 bytes_invalid=0 send_seq=5391 receive_seq=5391 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997197 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=164054 bytes_read=5101031 bytes_retransmit=9 bytes_invalid=0 send_seq=22574 receive_seq=22574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997566 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92907 bytes_read=2093759 bytes_retransmit=9 bytes_invalid=0 send_seq=12511 receive_seq=12511 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997299 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32785 bytes_read=1334351 bytes_retransmit=9 bytes_invalid=0 send_seq=5405 receive_seq=5405 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997583 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33271 bytes_read=100147 bytes_retransmit=9 bytes_invalid=0 send_seq=5392 receive_seq=5392 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87363 bytes_read=2089097 bytes_retransmit=0 bytes_invalid=0 send_seq=9951 receive_seq=9951 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998602 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=53.6 th1: temp=53.2 th2: temp=58.3 th3: temp=56.1 sysload=0.30 cputime=374.783 memavail=7393520 print_time=5254.936 buffer_time=2.093 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 78 Hz
Stats 5231.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23548567 bytes_read=3665238 bytes_retransmit=9 bytes_invalid=0 send_seq=442789 receive_seq=442789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=16781 freq=400016429 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=32524 bytes_read=102167 bytes_retransmit=0 bytes_invalid=0 send_seq=5392 receive_seq=5392 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997247 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=164130 bytes_read=5104088 bytes_retransmit=9 bytes_invalid=0 send_seq=22585 receive_seq=22585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997618 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92913 bytes_read=2093859 bytes_retransmit=9 bytes_invalid=0 send_seq=12512 receive_seq=12512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997361 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32791 bytes_read=1334585 bytes_retransmit=9 bytes_invalid=0 send_seq=5406 receive_seq=5406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33277 bytes_read=100163 bytes_retransmit=9 bytes_invalid=0 send_seq=5393 receive_seq=5393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87369 bytes_read=2089453 bytes_retransmit=0 bytes_invalid=0 send_seq=9952 receive_seq=9952 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998634 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=53.4 th1: temp=53.3 th2: temp=58.3 th3: temp=56.0 sysload=0.30 cputime=374.926 memavail=7393520 print_time=5256.143 buffer_time=2.299 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 79 Hz
Stats 5232.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23560082 bytes_read=3666572 bytes_retransmit=9 bytes_invalid=0 send_seq=442988 receive_seq=442988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=35 upcoming_bytes=16318 freq=400016393 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=32530 bytes_read=102183 bytes_retransmit=0 bytes_invalid=0 send_seq=5393 receive_seq=5393 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997289 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=164206 bytes_read=5107174 bytes_retransmit=9 bytes_invalid=0 send_seq=22596 receive_seq=22596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997659 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92919 bytes_read=2093987 bytes_retransmit=9 bytes_invalid=0 send_seq=12513 receive_seq=12513 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997451 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32797 bytes_read=1334879 bytes_retransmit=9 bytes_invalid=0 send_seq=5407 receive_seq=5407 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33283 bytes_read=100190 bytes_retransmit=9 bytes_invalid=0 send_seq=5394 receive_seq=5394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87375 bytes_read=2089809 bytes_retransmit=0 bytes_invalid=0 send_seq=9953 receive_seq=9953 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998662 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=53.4 th1: temp=53.2 th2: temp=58.2 th3: temp=56.1 sysload=0.30 cputime=375.052 memavail=7393520 print_time=5257.013 buffer_time=2.169 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 80 Hz
Stats 5233.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23572668 bytes_read=3667957 bytes_retransmit=9 bytes_invalid=0 send_seq=443203 receive_seq=443203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=15677 freq=400016347 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=32536 bytes_read=102199 bytes_retransmit=0 bytes_invalid=0 send_seq=5394 receive_seq=5394 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997362 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=164275 bytes_read=5110224 bytes_retransmit=9 bytes_invalid=0 send_seq=22606 receive_seq=22606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997722 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92925 bytes_read=2094101 bytes_retransmit=9 bytes_invalid=0 send_seq=12514 receive_seq=12514 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997495 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32803 bytes_read=1335128 bytes_retransmit=9 bytes_invalid=0 send_seq=5408 receive_seq=5408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997711 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33289 bytes_read=100206 bytes_retransmit=9 bytes_invalid=0 send_seq=5395 receive_seq=5395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999470 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87381 bytes_read=2090147 bytes_retransmit=0 bytes_invalid=0 send_seq=9954 receive_seq=9954 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998692 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=53.5 th1: temp=53.3 th2: temp=58.3 th3: temp=56.0 sysload=0.30 cputime=375.178 memavail=7393536 print_time=5257.949 buffer_time=2.104 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 81 Hz
Stats 5234.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23586334 bytes_read=3669461 bytes_retransmit=9 bytes_invalid=0 send_seq=443439 receive_seq=443439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=17504 freq=400016307 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32542 bytes_read=102228 bytes_retransmit=0 bytes_invalid=0 send_seq=5395 receive_seq=5395 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997411 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=164351 bytes_read=5113338 bytes_retransmit=9 bytes_invalid=0 send_seq=22617 receive_seq=22617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997775 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92931 bytes_read=2094201 bytes_retransmit=9 bytes_invalid=0 send_seq=12515 receive_seq=12515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997635 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32809 bytes_read=1335362 bytes_retransmit=9 bytes_invalid=0 send_seq=5409 receive_seq=5409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997753 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33295 bytes_read=100222 bytes_retransmit=9 bytes_invalid=0 send_seq=5396 receive_seq=5396 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999479 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87387 bytes_read=2090521 bytes_retransmit=0 bytes_invalid=0 send_seq=9955 receive_seq=9955 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998727 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=53.4 th1: temp=53.2 th2: temp=58.3 th3: temp=56.0 sysload=0.30 cputime=375.324 memavail=7393548 print_time=5259.154 buffer_time=2.305 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 82 Hz
Stats 5235.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23598223 bytes_read=3670811 bytes_retransmit=9 bytes_invalid=0 send_seq=443644 receive_seq=443644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=16772 freq=400016279 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32548 bytes_read=102244 bytes_retransmit=0 bytes_invalid=0 send_seq=5396 receive_seq=5396 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997407 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=164427 bytes_read=5116424 bytes_retransmit=9 bytes_invalid=0 send_seq=22628 receive_seq=22628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997780 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92937 bytes_read=2094329 bytes_retransmit=9 bytes_invalid=0 send_seq=12516 receive_seq=12516 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997630 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32815 bytes_read=1335656 bytes_retransmit=9 bytes_invalid=0 send_seq=5410 receive_seq=5410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997760 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33301 bytes_read=100238 bytes_retransmit=9 bytes_invalid=0 send_seq=5397 receive_seq=5397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999476 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87393 bytes_read=2090877 bytes_retransmit=0 bytes_invalid=0 send_seq=9956 receive_seq=9956 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998732 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=53.3 th1: temp=53.3 th2: temp=58.3 th3: temp=56.1 sysload=0.36 cputime=375.459 memavail=7393548 print_time=5260.025 buffer_time=2.176 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 83 Hz
Stats 5236.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23610941 bytes_read=3672237 bytes_retransmit=9 bytes_invalid=0 send_seq=443864 receive_seq=443864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=16647 freq=400016321 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32554 bytes_read=102260 bytes_retransmit=0 bytes_invalid=0 send_seq=5397 receive_seq=5397 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997423 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=164503 bytes_read=5119483 bytes_retransmit=9 bytes_invalid=0 send_seq=22639 receive_seq=22639 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997798 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92943 bytes_read=2094429 bytes_retransmit=9 bytes_invalid=0 send_seq=12517 receive_seq=12517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997668 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32821 bytes_read=1335890 bytes_retransmit=9 bytes_invalid=0 send_seq=5411 receive_seq=5411 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997777 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33307 bytes_read=100254 bytes_retransmit=9 bytes_invalid=0 send_seq=5398 receive_seq=5398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999480 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87399 bytes_read=2091233 bytes_retransmit=0 bytes_invalid=0 send_seq=9957 receive_seq=9957 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998746 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=53.4 th1: temp=53.2 th2: temp=58.7 th3: temp=56.0 sysload=0.36 cputime=375.600 memavail=7390020 print_time=5260.969 buffer_time=2.119 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 84 Hz
Stats 5237.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23624920 bytes_read=3673771 bytes_retransmit=9 bytes_invalid=0 send_seq=444106 receive_seq=444106 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=17845 freq=400016369 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32560 bytes_read=102276 bytes_retransmit=0 bytes_invalid=0 send_seq=5398 receive_seq=5398 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997317 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=164579 bytes_read=5122540 bytes_retransmit=9 bytes_invalid=0 send_seq=22650 receive_seq=22650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997748 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92949 bytes_read=2094529 bytes_retransmit=9 bytes_invalid=0 send_seq=12518 receive_seq=12518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997518 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32827 bytes_read=1336124 bytes_retransmit=9 bytes_invalid=0 send_seq=5412 receive_seq=5412 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33313 bytes_read=100281 bytes_retransmit=9 bytes_invalid=0 send_seq=5399 receive_seq=5399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87405 bytes_read=2091589 bytes_retransmit=0 bytes_invalid=0 send_seq=9958 receive_seq=9958 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998684 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=53.4 th1: temp=53.4 th2: temp=58.3 th3: temp=56.0 sysload=0.36 cputime=375.760 memavail=7394412 print_time=5262.160 buffer_time=2.309 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 85 Hz
Stats 5238.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23637002 bytes_read=3675146 bytes_retransmit=9 bytes_invalid=0 send_seq=444316 receive_seq=444316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=17222 freq=400016418 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32566 bytes_read=102292 bytes_retransmit=0 bytes_invalid=0 send_seq=5399 receive_seq=5399 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997248 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=164655 bytes_read=5125643 bytes_retransmit=9 bytes_invalid=0 send_seq=22661 receive_seq=22661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997596 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92955 bytes_read=2094671 bytes_retransmit=9 bytes_invalid=0 send_seq=12519 receive_seq=12519 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997390 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32833 bytes_read=1336433 bytes_retransmit=9 bytes_invalid=0 send_seq=5413 receive_seq=5413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997586 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33319 bytes_read=100297 bytes_retransmit=9 bytes_invalid=0 send_seq=5400 receive_seq=5400 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999429 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87411 bytes_read=2091945 bytes_retransmit=0 bytes_invalid=0 send_seq=9959 receive_seq=9959 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998627 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=53.4 th1: temp=53.3 th2: temp=58.5 th3: temp=56.0 sysload=0.36 cputime=375.894 memavail=7394412 print_time=5263.034 buffer_time=2.182 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 86 Hz
Stats 5239.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23649697 bytes_read=3676552 bytes_retransmit=9 bytes_invalid=0 send_seq=444536 receive_seq=444536 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=17520 freq=400016405 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32572 bytes_read=102321 bytes_retransmit=0 bytes_invalid=0 send_seq=5400 receive_seq=5400 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997163 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=164731 bytes_read=5128700 bytes_retransmit=9 bytes_invalid=0 send_seq=22672 receive_seq=22672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997482 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92961 bytes_read=2094771 bytes_retransmit=9 bytes_invalid=0 send_seq=12520 receive_seq=12520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997269 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32839 bytes_read=1336667 bytes_retransmit=9 bytes_invalid=0 send_seq=5414 receive_seq=5414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997510 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33325 bytes_read=100313 bytes_retransmit=9 bytes_invalid=0 send_seq=5401 receive_seq=5401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999412 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87417 bytes_read=2092285 bytes_retransmit=0 bytes_invalid=0 send_seq=9960 receive_seq=9960 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998580 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=53.4 th1: temp=53.3 th2: temp=58.5 th3: temp=56.0 sysload=0.36 cputime=376.024 memavail=7394412 print_time=5263.970 buffer_time=2.118 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 87 Hz
Stats 5240.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23664196 bytes_read=3678116 bytes_retransmit=9 bytes_invalid=0 send_seq=444784 receive_seq=444784 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=15 upcoming_bytes=18946 freq=400016450 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32578 bytes_read=102337 bytes_retransmit=0 bytes_invalid=0 send_seq=5401 receive_seq=5401 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997202 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=164807 bytes_read=5131756 bytes_retransmit=9 bytes_invalid=0 send_seq=22683 receive_seq=22683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997512 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92967 bytes_read=2094871 bytes_retransmit=9 bytes_invalid=0 send_seq=12521 receive_seq=12521 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997418 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32845 bytes_read=1336901 bytes_retransmit=9 bytes_invalid=0 send_seq=5415 receive_seq=5415 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997541 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33331 bytes_read=100329 bytes_retransmit=9 bytes_invalid=0 send_seq=5402 receive_seq=5402 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999417 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87423 bytes_read=2092641 bytes_retransmit=0 bytes_invalid=0 send_seq=9961 receive_seq=9961 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998625 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=53.6 th1: temp=53.3 th2: temp=58.4 th3: temp=56.0 sysload=0.33 cputime=376.172 memavail=7394412 print_time=5265.170 buffer_time=2.317 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 88 Hz
Stats 5241.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23676659 bytes_read=3679537 bytes_retransmit=9 bytes_invalid=0 send_seq=445000 receive_seq=445000 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=17688 freq=400016414 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32584 bytes_read=102353 bytes_retransmit=0 bytes_invalid=0 send_seq=5402 receive_seq=5402 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997136 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=164883 bytes_read=5134840 bytes_retransmit=9 bytes_invalid=0 send_seq=22694 receive_seq=22694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997445 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92973 bytes_read=2094999 bytes_retransmit=9 bytes_invalid=0 send_seq=12522 receive_seq=12522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997316 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32851 bytes_read=1337195 bytes_retransmit=9 bytes_invalid=0 send_seq=5416 receive_seq=5416 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997495 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33337 bytes_read=100345 bytes_retransmit=9 bytes_invalid=0 send_seq=5403 receive_seq=5403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999416 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87429 bytes_read=2092997 bytes_retransmit=0 bytes_invalid=0 send_seq=9962 receive_seq=9962 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998612 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=53.4 th1: temp=53.4 th2: temp=58.4 th3: temp=56.1 sysload=0.33 cputime=376.306 memavail=7394412 print_time=5266.039 buffer_time=2.186 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 89 Hz
Stats 5242.2: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23689726 bytes_read=3680982 bytes_retransmit=9 bytes_invalid=0 send_seq=445227 receive_seq=445227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=17740 freq=400016371 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32590 bytes_read=102369 bytes_retransmit=0 bytes_invalid=0 send_seq=5403 receive_seq=5403 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997191 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=164959 bytes_read=5137957 bytes_retransmit=9 bytes_invalid=0 send_seq=22705 receive_seq=22705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997510 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92979 bytes_read=2095099 bytes_retransmit=9 bytes_invalid=0 send_seq=12523 receive_seq=12523 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997374 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32857 bytes_read=1337429 bytes_retransmit=9 bytes_invalid=0 send_seq=5417 receive_seq=5417 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997552 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33343 bytes_read=100372 bytes_retransmit=9 bytes_invalid=0 send_seq=5404 receive_seq=5404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87435 bytes_read=2093353 bytes_retransmit=0 bytes_invalid=0 send_seq=9963 receive_seq=9963 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998686 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=53.3 th1: temp=53.3 th2: temp=58.4 th3: temp=56.0 sysload=0.33 cputime=376.439 memavail=7394416 print_time=5266.972 buffer_time=2.119 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 90 Hz
Stats 5243.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23704430 bytes_read=3682566 bytes_retransmit=9 bytes_invalid=0 send_seq=445476 receive_seq=445476 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=29 upcoming_bytes=19057 freq=400016346 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32596 bytes_read=102385 bytes_retransmit=0 bytes_invalid=0 send_seq=5404 receive_seq=5404 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997249 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=165035 bytes_read=5141046 bytes_retransmit=9 bytes_invalid=0 send_seq=22716 receive_seq=22716 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997590 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92985 bytes_read=2095213 bytes_retransmit=9 bytes_invalid=0 send_seq=12524 receive_seq=12524 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997502 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32863 bytes_read=1337678 bytes_retransmit=9 bytes_invalid=0 send_seq=5418 receive_seq=5418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997618 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33349 bytes_read=100388 bytes_retransmit=9 bytes_invalid=0 send_seq=5405 receive_seq=5405 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87441 bytes_read=2093725 bytes_retransmit=0 bytes_invalid=0 send_seq=9964 receive_seq=9964 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998707 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=53.5 th1: temp=53.5 th2: temp=58.4 th3: temp=56.0 sysload=0.33 cputime=376.590 memavail=7394416 print_time=5268.178 buffer_time=2.312 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 91 Hz
Stats 5244.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23717312 bytes_read=3684001 bytes_retransmit=9 bytes_invalid=0 send_seq=445701 receive_seq=445701 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=17570 freq=400016312 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32602 bytes_read=102414 bytes_retransmit=0 bytes_invalid=0 send_seq=5405 receive_seq=5405 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997283 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=165111 bytes_read=5144117 bytes_retransmit=9 bytes_invalid=0 send_seq=22727 receive_seq=22727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997622 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92991 bytes_read=2095341 bytes_retransmit=9 bytes_invalid=0 send_seq=12525 receive_seq=12525 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997541 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32869 bytes_read=1337972 bytes_retransmit=9 bytes_invalid=0 send_seq=5419 receive_seq=5419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997649 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33355 bytes_read=100404 bytes_retransmit=9 bytes_invalid=0 send_seq=5406 receive_seq=5406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87447 bytes_read=2094081 bytes_retransmit=0 bytes_invalid=0 send_seq=9965 receive_seq=9965 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998701 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=53.3 th1: temp=53.3 th2: temp=58.5 th3: temp=56.1 sysload=0.33 cputime=376.723 memavail=7394416 print_time=5269.054 buffer_time=2.187 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 92 Hz
Stats 5245.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23730150 bytes_read=3685421 bytes_retransmit=9 bytes_invalid=0 send_seq=445923 receive_seq=445923 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=18257 freq=400016366 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32608 bytes_read=102430 bytes_retransmit=0 bytes_invalid=0 send_seq=5406 receive_seq=5406 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997323 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=165187 bytes_read=5147232 bytes_retransmit=9 bytes_invalid=0 send_seq=22738 receive_seq=22738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997701 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=92997 bytes_read=2095441 bytes_retransmit=9 bytes_invalid=0 send_seq=12526 receive_seq=12526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997618 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32875 bytes_read=1338206 bytes_retransmit=9 bytes_invalid=0 send_seq=5420 receive_seq=5420 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997690 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33361 bytes_read=100420 bytes_retransmit=9 bytes_invalid=0 send_seq=5407 receive_seq=5407 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999467 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87453 bytes_read=2094437 bytes_retransmit=0 bytes_invalid=0 send_seq=9966 receive_seq=9966 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998720 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=53.6 th1: temp=53.4 th2: temp=58.6 th3: temp=56.1 sysload=0.30 cputime=376.855 memavail=7394416 print_time=5269.989 buffer_time=2.122 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 93 Hz
Stats 5246.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23744884 bytes_read=3687046 bytes_retransmit=9 bytes_invalid=0 send_seq=446177 receive_seq=446177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=19775 freq=400016406 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32614 bytes_read=102446 bytes_retransmit=0 bytes_invalid=0 send_seq=5407 receive_seq=5407 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997220 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=165263 bytes_read=5150303 bytes_retransmit=9 bytes_invalid=0 send_seq=22749 receive_seq=22749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997576 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93003 bytes_read=2095555 bytes_retransmit=9 bytes_invalid=0 send_seq=12527 receive_seq=12527 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997491 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32881 bytes_read=1338440 bytes_retransmit=9 bytes_invalid=0 send_seq=5421 receive_seq=5421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997597 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33367 bytes_read=100436 bytes_retransmit=9 bytes_invalid=0 send_seq=5408 receive_seq=5408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87459 bytes_read=2094793 bytes_retransmit=0 bytes_invalid=0 send_seq=9967 receive_seq=9967 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998644 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=53.4 th1: temp=53.4 th2: temp=58.4 th3: temp=56.1 sysload=0.30 cputime=377.006 memavail=7394416 print_time=5271.186 buffer_time=2.312 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 94 Hz
Stats 5247.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23758124 bytes_read=3688501 bytes_retransmit=9 bytes_invalid=0 send_seq=446406 receive_seq=446406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=17901 freq=400016363 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32620 bytes_read=102462 bytes_retransmit=0 bytes_invalid=0 send_seq=5408 receive_seq=5408 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997154 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=165339 bytes_read=5153374 bytes_retransmit=9 bytes_invalid=0 send_seq=22760 receive_seq=22760 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997487 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93009 bytes_read=2095669 bytes_retransmit=9 bytes_invalid=0 send_seq=12528 receive_seq=12528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997373 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32887 bytes_read=1338734 bytes_retransmit=9 bytes_invalid=0 send_seq=5422 receive_seq=5422 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997532 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33373 bytes_read=100463 bytes_retransmit=9 bytes_invalid=0 send_seq=5409 receive_seq=5409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999417 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87465 bytes_read=2095149 bytes_retransmit=0 bytes_invalid=0 send_seq=9968 receive_seq=9968 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998608 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=53.5 th1: temp=53.4 th2: temp=58.4 th3: temp=56.1 sysload=0.30 cputime=377.142 memavail=7394452 print_time=5272.058 buffer_time=2.183 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 95 Hz
Stats 5248.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23770942 bytes_read=3689926 bytes_retransmit=9 bytes_invalid=0 send_seq=446629 receive_seq=446629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=19088 freq=400016319 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32626 bytes_read=102478 bytes_retransmit=0 bytes_invalid=0 send_seq=5409 receive_seq=5409 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997222 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=165415 bytes_read=5156447 bytes_retransmit=9 bytes_invalid=0 send_seq=22771 receive_seq=22771 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997577 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93015 bytes_read=2095783 bytes_retransmit=9 bytes_invalid=0 send_seq=12529 receive_seq=12529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32893 bytes_read=1338983 bytes_retransmit=9 bytes_invalid=0 send_seq=5423 receive_seq=5423 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997592 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33379 bytes_read=100479 bytes_retransmit=9 bytes_invalid=0 send_seq=5410 receive_seq=5410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87471 bytes_read=2095505 bytes_retransmit=0 bytes_invalid=0 send_seq=9969 receive_seq=9969 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998642 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=53.4 th1: temp=53.3 th2: temp=58.4 th3: temp=56.0 sysload=0.30 cputime=377.276 memavail=7394452 print_time=5272.995 buffer_time=2.120 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 96 Hz
Stats 5249.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23786233 bytes_read=3691599 bytes_retransmit=9 bytes_invalid=0 send_seq=446894 receive_seq=446894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=20673 freq=400016255 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32638 bytes_read=102521 bytes_retransmit=0 bytes_invalid=0 send_seq=5411 receive_seq=5411 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997299 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=165490 bytes_read=5159585 bytes_retransmit=9 bytes_invalid=0 send_seq=22782 receive_seq=22782 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997666 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93027 bytes_read=2095913 bytes_retransmit=9 bytes_invalid=0 send_seq=12531 receive_seq=12531 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997543 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32905 bytes_read=1339233 bytes_retransmit=9 bytes_invalid=0 send_seq=5425 receive_seq=5425 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33391 bytes_read=100511 bytes_retransmit=9 bytes_invalid=0 send_seq=5412 receive_seq=5412 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87483 bytes_read=2095877 bytes_retransmit=0 bytes_invalid=0 send_seq=9971 receive_seq=9971 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998674 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=53.5 th1: temp=53.4 th2: temp=58.3 th3: temp=56.2 sysload=0.30 cputime=377.434 memavail=7394452 print_time=5274.199 buffer_time=2.316 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 97 Hz
Stats 5250.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23799980 bytes_read=3693102 bytes_retransmit=9 bytes_invalid=0 send_seq=447134 receive_seq=447133 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=18288 freq=400016215 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32644 bytes_read=102536 bytes_retransmit=0 bytes_invalid=0 send_seq=5412 receive_seq=5412 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997364 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=165566 bytes_read=5162642 bytes_retransmit=9 bytes_invalid=0 send_seq=22793 receive_seq=22793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997840 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93033 bytes_read=2096027 bytes_retransmit=9 bytes_invalid=0 send_seq=12532 receive_seq=12532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997583 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32911 bytes_read=1339527 bytes_retransmit=9 bytes_invalid=0 send_seq=5426 receive_seq=5426 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997722 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33397 bytes_read=100527 bytes_retransmit=9 bytes_invalid=0 send_seq=5413 receive_seq=5413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87489 bytes_read=2096233 bytes_retransmit=0 bytes_invalid=0 send_seq=9972 receive_seq=9972 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998732 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=53.4 th1: temp=53.4 th2: temp=58.3 th3: temp=56.1 sysload=0.36 cputime=377.575 memavail=7394452 print_time=5275.067 buffer_time=2.183 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 98 Hz
Stats 5251.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23813054 bytes_read=3694553 bytes_retransmit=9 bytes_invalid=0 send_seq=447358 receive_seq=447358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=19431 freq=400016194 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32650 bytes_read=102551 bytes_retransmit=0 bytes_invalid=0 send_seq=5413 receive_seq=5413 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997406 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=165642 bytes_read=5165701 bytes_retransmit=9 bytes_invalid=0 send_seq=22804 receive_seq=22804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997878 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93039 bytes_read=2096127 bytes_retransmit=9 bytes_invalid=0 send_seq=12533 receive_seq=12533 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997637 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32917 bytes_read=1339761 bytes_retransmit=9 bytes_invalid=0 send_seq=5427 receive_seq=5427 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997764 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33403 bytes_read=100543 bytes_retransmit=9 bytes_invalid=0 send_seq=5414 receive_seq=5414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999481 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87495 bytes_read=2096589 bytes_retransmit=0 bytes_invalid=0 send_seq=9973 receive_seq=9973 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998760 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=53.3 th1: temp=53.3 th2: temp=58.4 th3: temp=56.1 sysload=0.36 cputime=377.718 memavail=7394200 print_time=5275.998 buffer_time=2.114 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 99 Hz
Stats 5252.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23828292 bytes_read=3696207 bytes_retransmit=9 bytes_invalid=0 send_seq=447621 receive_seq=447621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=21047 freq=400016164 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32656 bytes_read=102566 bytes_retransmit=0 bytes_invalid=0 send_seq=5414 receive_seq=5414 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997418 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=165718 bytes_read=5168788 bytes_retransmit=9 bytes_invalid=0 send_seq=22815 receive_seq=22815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997881 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93045 bytes_read=2096241 bytes_retransmit=9 bytes_invalid=0 send_seq=12534 receive_seq=12534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997626 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=32923 bytes_read=1339995 bytes_retransmit=9 bytes_invalid=0 send_seq=5428 receive_seq=5428 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997773 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33409 bytes_read=100570 bytes_retransmit=9 bytes_invalid=0 send_seq=5415 receive_seq=5415 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999482 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87501 bytes_read=2096945 bytes_retransmit=0 bytes_invalid=0 send_seq=9974 receive_seq=9974 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998760 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.012 th0: temp=53.5 th1: temp=53.4 th2: temp=58.5 th3: temp=56.0 sysload=0.36 cputime=377.873 memavail=7394212 print_time=5277.198 buffer_time=2.312 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 100 Hz
Stats 5253.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23842399 bytes_read=3697727 bytes_retransmit=9 bytes_invalid=0 send_seq=447863 receive_seq=447863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=18607 freq=400016138 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32662 bytes_read=102582 bytes_retransmit=0 bytes_invalid=0 send_seq=5415 receive_seq=5415 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997404 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=165794 bytes_read=5171861 bytes_retransmit=9 bytes_invalid=0 send_seq=22826 receive_seq=22826 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997844 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93051 bytes_read=2096369 bytes_retransmit=9 bytes_invalid=0 send_seq=12535 receive_seq=12535 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997621 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32929 bytes_read=1340304 bytes_retransmit=9 bytes_invalid=0 send_seq=5429 receive_seq=5429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997765 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33415 bytes_read=100586 bytes_retransmit=9 bytes_invalid=0 send_seq=5416 receive_seq=5416 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999481 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87507 bytes_read=2097301 bytes_retransmit=0 bytes_invalid=0 send_seq=9975 receive_seq=9975 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998743 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=53.5 th1: temp=53.5 th2: temp=58.4 th3: temp=56.1 sysload=0.36 cputime=378.011 memavail=7394212 print_time=5278.068 buffer_time=2.181 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 101 Hz
Stats 5254.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23855603 bytes_read=3699192 bytes_retransmit=9 bytes_invalid=0 send_seq=448094 receive_seq=448094 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=19912 freq=400016099 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32668 bytes_read=102611 bytes_retransmit=0 bytes_invalid=0 send_seq=5416 receive_seq=5416 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997429 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=165870 bytes_read=5174978 bytes_retransmit=9 bytes_invalid=0 send_seq=22837 receive_seq=22837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997876 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93057 bytes_read=2096469 bytes_retransmit=9 bytes_invalid=0 send_seq=12536 receive_seq=12536 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997635 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32935 bytes_read=1340538 bytes_retransmit=9 bytes_invalid=0 send_seq=5430 receive_seq=5430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997784 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33421 bytes_read=100602 bytes_retransmit=9 bytes_invalid=0 send_seq=5417 receive_seq=5417 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999488 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87513 bytes_read=2097657 bytes_retransmit=0 bytes_invalid=0 send_seq=9976 receive_seq=9976 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998787 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=53.8 th1: temp=53.4 th2: temp=58.3 th3: temp=56.1 sysload=0.36 cputime=378.160 memavail=7395216 print_time=5279.006 buffer_time=2.119 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 102 Hz
Stats 5255.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23871188 bytes_read=3700851 bytes_retransmit=9 bytes_invalid=0 send_seq=448358 receive_seq=448358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=21445 freq=400016079 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32674 bytes_read=102627 bytes_retransmit=0 bytes_invalid=0 send_seq=5417 receive_seq=5417 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997447 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=165946 bytes_read=5178064 bytes_retransmit=9 bytes_invalid=0 send_seq=22848 receive_seq=22848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997907 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93063 bytes_read=2096597 bytes_retransmit=9 bytes_invalid=0 send_seq=12537 receive_seq=12537 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997660 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32941 bytes_read=1340781 bytes_retransmit=9 bytes_invalid=0 send_seq=5431 receive_seq=5431 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997812 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33427 bytes_read=100618 bytes_retransmit=9 bytes_invalid=0 send_seq=5418 receive_seq=5418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999492 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87519 bytes_read=2098013 bytes_retransmit=0 bytes_invalid=0 send_seq=9977 receive_seq=9977 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998792 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.012 th0: temp=53.7 th1: temp=53.4 th2: temp=58.3 th3: temp=56.1 sysload=0.33 cputime=378.316 memavail=7395216 print_time=5280.208 buffer_time=2.314 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 103 Hz
Stats 5256.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23885552 bytes_read=3702417 bytes_retransmit=9 bytes_invalid=0 send_seq=448606 receive_seq=448606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=18933 freq=400016062 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32680 bytes_read=102643 bytes_retransmit=0 bytes_invalid=0 send_seq=5418 receive_seq=5418 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997401 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=166022 bytes_read=5181122 bytes_retransmit=9 bytes_invalid=0 send_seq=22859 receive_seq=22859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997858 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93069 bytes_read=2096697 bytes_retransmit=9 bytes_invalid=0 send_seq=12538 receive_seq=12538 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997619 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32947 bytes_read=1341037 bytes_retransmit=9 bytes_invalid=0 send_seq=5432 receive_seq=5432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997787 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33433 bytes_read=100634 bytes_retransmit=9 bytes_invalid=0 send_seq=5419 receive_seq=5419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999484 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87525 bytes_read=2098369 bytes_retransmit=0 bytes_invalid=0 send_seq=9978 receive_seq=9978 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998759 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.012 th0: temp=53.4 th1: temp=53.5 th2: temp=58.6 th3: temp=56.2 sysload=0.33 cputime=378.456 memavail=7395216 print_time=5281.078 buffer_time=2.184 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 104 Hz
Stats 5257.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23898830 bytes_read=3703872 bytes_retransmit=9 bytes_invalid=0 send_seq=448835 receive_seq=448835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=23 upcoming_bytes=20541 freq=400016041 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32686 bytes_read=102659 bytes_retransmit=0 bytes_invalid=0 send_seq=5419 receive_seq=5419 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997411 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=166098 bytes_read=5184179 bytes_retransmit=9 bytes_invalid=0 send_seq=22870 receive_seq=22870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997982 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93075 bytes_read=2096797 bytes_retransmit=9 bytes_invalid=0 send_seq=12539 receive_seq=12539 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997614 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32953 bytes_read=1341255 bytes_retransmit=9 bytes_invalid=0 send_seq=5433 receive_seq=5433 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997791 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33439 bytes_read=100661 bytes_retransmit=9 bytes_invalid=0 send_seq=5420 receive_seq=5420 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999482 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87531 bytes_read=2098725 bytes_retransmit=0 bytes_invalid=0 send_seq=9979 receive_seq=9979 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998760 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.3 th1: temp=53.2 th2: temp=58.5 th3: temp=56.1 sysload=0.33 cputime=378.595 memavail=7394528 print_time=5282.009 buffer_time=2.114 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 105 Hz
Stats 5258.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23914600 bytes_read=3705561 bytes_retransmit=9 bytes_invalid=0 send_seq=449105 receive_seq=449105 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=46 upcoming_bytes=22385 freq=400016036 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32692 bytes_read=102675 bytes_retransmit=0 bytes_invalid=0 send_seq=5420 receive_seq=5420 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997426 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=166174 bytes_read=5187338 bytes_retransmit=9 bytes_invalid=0 send_seq=22881 receive_seq=22881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997971 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93081 bytes_read=2096939 bytes_retransmit=9 bytes_invalid=0 send_seq=12540 receive_seq=12540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997619 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32959 bytes_read=1341502 bytes_retransmit=9 bytes_invalid=0 send_seq=5434 receive_seq=5434 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997794 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33445 bytes_read=100677 bytes_retransmit=9 bytes_invalid=0 send_seq=5421 receive_seq=5421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999481 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87537 bytes_read=2099081 bytes_retransmit=0 bytes_invalid=0 send_seq=9980 receive_seq=9980 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998761 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.5 th1: temp=53.4 th2: temp=58.2 th3: temp=56.1 sysload=0.33 cputime=378.753 memavail=7394532 print_time=5283.214 buffer_time=2.314 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 106 Hz
Stats 5259.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23929654 bytes_read=3707171 bytes_retransmit=9 bytes_invalid=0 send_seq=449365 receive_seq=449365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=19188 freq=400016013 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32698 bytes_read=102704 bytes_retransmit=0 bytes_invalid=0 send_seq=5421 receive_seq=5421 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997388 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=166250 bytes_read=5190395 bytes_retransmit=9 bytes_invalid=0 send_seq=22892 receive_seq=22892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997868 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93087 bytes_read=2097039 bytes_retransmit=9 bytes_invalid=0 send_seq=12541 receive_seq=12541 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997584 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32965 bytes_read=1341762 bytes_retransmit=9 bytes_invalid=0 send_seq=5435 receive_seq=5435 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997752 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33451 bytes_read=100693 bytes_retransmit=9 bytes_invalid=0 send_seq=5422 receive_seq=5422 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999470 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87543 bytes_read=2099437 bytes_retransmit=0 bytes_invalid=0 send_seq=9981 receive_seq=9981 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998727 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.012 th0: temp=53.7 th1: temp=53.5 th2: temp=58.5 th3: temp=56.3 sysload=0.33 cputime=378.899 memavail=7394532 print_time=5284.074 buffer_time=2.173 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 107 Hz
Stats 5260.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23943010 bytes_read=3708632 bytes_retransmit=9 bytes_invalid=0 send_seq=449596 receive_seq=449596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=21005 freq=400015981 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32704 bytes_read=102720 bytes_retransmit=0 bytes_invalid=0 send_seq=5422 receive_seq=5422 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997409 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=166326 bytes_read=5193452 bytes_retransmit=9 bytes_invalid=0 send_seq=22903 receive_seq=22903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997886 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93093 bytes_read=2097139 bytes_retransmit=9 bytes_invalid=0 send_seq=12542 receive_seq=12542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997606 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32971 bytes_read=1341980 bytes_retransmit=9 bytes_invalid=0 send_seq=5436 receive_seq=5436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997771 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33457 bytes_read=100709 bytes_retransmit=9 bytes_invalid=0 send_seq=5423 receive_seq=5423 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999471 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87549 bytes_read=2099793 bytes_retransmit=0 bytes_invalid=0 send_seq=9982 receive_seq=9982 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998738 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=53.3 th1: temp=53.5 th2: temp=58.5 th3: temp=56.1 sysload=0.30 cputime=379.043 memavail=7394532 print_time=5285.011 buffer_time=2.110 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 108 Hz
Stats 5261.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23959125 bytes_read=3710360 bytes_retransmit=9 bytes_invalid=0 send_seq=449871 receive_seq=449871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=22759 freq=400015961 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32710 bytes_read=102736 bytes_retransmit=0 bytes_invalid=0 send_seq=5423 receive_seq=5423 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997438 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=166402 bytes_read=5196536 bytes_retransmit=9 bytes_invalid=0 send_seq=22914 receive_seq=22914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997899 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93099 bytes_read=2097267 bytes_retransmit=9 bytes_invalid=0 send_seq=12543 receive_seq=12543 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997657 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32977 bytes_read=1342243 bytes_retransmit=9 bytes_invalid=0 send_seq=5437 receive_seq=5437 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997801 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33463 bytes_read=100725 bytes_retransmit=9 bytes_invalid=0 send_seq=5424 receive_seq=5424 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999476 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87555 bytes_read=2100149 bytes_retransmit=0 bytes_invalid=0 send_seq=9983 receive_seq=9983 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998749 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.012 th0: temp=53.6 th1: temp=53.1 th2: temp=58.5 th3: temp=56.2 sysload=0.30 cputime=379.208 memavail=7394552 print_time=5286.211 buffer_time=2.306 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 109 Hz
Stats 5262.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23974278 bytes_read=3711960 bytes_retransmit=9 bytes_invalid=0 send_seq=450129 receive_seq=450129 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=19857 freq=400015944 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32716 bytes_read=102752 bytes_retransmit=0 bytes_invalid=0 send_seq=5424 receive_seq=5424 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997414 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=166478 bytes_read=5199594 bytes_retransmit=9 bytes_invalid=0 send_seq=22925 receive_seq=22925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997852 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93105 bytes_read=2097367 bytes_retransmit=9 bytes_invalid=0 send_seq=12544 receive_seq=12544 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997626 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32983 bytes_read=1342507 bytes_retransmit=9 bytes_invalid=0 send_seq=5438 receive_seq=5438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997779 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33469 bytes_read=100752 bytes_retransmit=9 bytes_invalid=0 send_seq=5425 receive_seq=5425 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999471 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87561 bytes_read=2100505 bytes_retransmit=0 bytes_invalid=0 send_seq=9984 receive_seq=9984 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998740 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=53.7 th1: temp=53.5 th2: temp=58.5 th3: temp=56.2 sysload=0.30 cputime=379.355 memavail=7394552 print_time=5287.091 buffer_time=2.185 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 110 Hz
Stats 5263.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=23987886 bytes_read=3713440 bytes_retransmit=9 bytes_invalid=0 send_seq=450363 receive_seq=450363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=21601 freq=400015944 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32722 bytes_read=102768 bytes_retransmit=0 bytes_invalid=0 send_seq=5425 receive_seq=5425 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997416 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=166547 bytes_read=5202645 bytes_retransmit=9 bytes_invalid=0 send_seq=22935 receive_seq=22935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997849 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93111 bytes_read=2097481 bytes_retransmit=9 bytes_invalid=0 send_seq=12545 receive_seq=12545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997631 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32989 bytes_read=1342756 bytes_retransmit=9 bytes_invalid=0 send_seq=5439 receive_seq=5439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997788 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33475 bytes_read=100768 bytes_retransmit=9 bytes_invalid=0 send_seq=5426 receive_seq=5426 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999478 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87567 bytes_read=2100861 bytes_retransmit=0 bytes_invalid=0 send_seq=9985 receive_seq=9985 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998747 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=53.6 th1: temp=53.4 th2: temp=58.4 th3: temp=56.3 sysload=0.30 cputime=379.500 memavail=7394552 print_time=5288.018 buffer_time=2.112 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 111 Hz
Stats 5264.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24004346 bytes_read=3715189 bytes_retransmit=9 bytes_invalid=0 send_seq=450645 receive_seq=450645 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=23281 freq=400015938 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32728 bytes_read=102797 bytes_retransmit=0 bytes_invalid=0 send_seq=5426 receive_seq=5426 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997392 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=166623 bytes_read=5205790 bytes_retransmit=9 bytes_invalid=0 send_seq=22946 receive_seq=22946 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997810 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93117 bytes_read=2097609 bytes_retransmit=9 bytes_invalid=0 send_seq=12546 receive_seq=12546 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997597 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=32995 bytes_read=1343020 bytes_retransmit=9 bytes_invalid=0 send_seq=5440 receive_seq=5440 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997765 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33481 bytes_read=100784 bytes_retransmit=9 bytes_invalid=0 send_seq=5427 receive_seq=5427 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999470 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87573 bytes_read=2101217 bytes_retransmit=0 bytes_invalid=0 send_seq=9986 receive_seq=9986 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998737 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=53.6 th1: temp=53.5 th2: temp=58.6 th3: temp=56.3 sysload=0.30 cputime=379.668 memavail=7394552 print_time=5289.216 buffer_time=2.306 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 112 Hz
Stats 5265.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24019934 bytes_read=3716849 bytes_retransmit=9 bytes_invalid=0 send_seq=450915 receive_seq=450915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=19875 freq=400015912 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32734 bytes_read=102813 bytes_retransmit=0 bytes_invalid=0 send_seq=5427 receive_seq=5427 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997362 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=166699 bytes_read=5208846 bytes_retransmit=9 bytes_invalid=0 send_seq=22957 receive_seq=22957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997775 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93123 bytes_read=2097709 bytes_retransmit=9 bytes_invalid=0 send_seq=12547 receive_seq=12547 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997595 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33001 bytes_read=1343284 bytes_retransmit=9 bytes_invalid=0 send_seq=5441 receive_seq=5441 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997750 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33487 bytes_read=100800 bytes_retransmit=9 bytes_invalid=0 send_seq=5428 receive_seq=5428 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999461 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87579 bytes_read=2101573 bytes_retransmit=0 bytes_invalid=0 send_seq=9987 receive_seq=9987 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998725 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=53.3 th1: temp=53.5 th2: temp=58.5 th3: temp=56.3 sysload=0.36 cputime=379.814 memavail=7394552 print_time=5290.088 buffer_time=2.178 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 113 Hz
Stats 5266.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24033718 bytes_read=3718365 bytes_retransmit=9 bytes_invalid=0 send_seq=451153 receive_seq=451153 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=21717 freq=400015898 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32740 bytes_read=102829 bytes_retransmit=0 bytes_invalid=0 send_seq=5428 receive_seq=5428 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997386 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=166775 bytes_read=5211902 bytes_retransmit=9 bytes_invalid=0 send_seq=22968 receive_seq=22968 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997827 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93129 bytes_read=2097809 bytes_retransmit=9 bytes_invalid=0 send_seq=12548 receive_seq=12548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997626 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33007 bytes_read=1343518 bytes_retransmit=9 bytes_invalid=0 send_seq=5442 receive_seq=5442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997775 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33493 bytes_read=100816 bytes_retransmit=9 bytes_invalid=0 send_seq=5429 receive_seq=5429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999467 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87585 bytes_read=2101929 bytes_retransmit=0 bytes_invalid=0 send_seq=9988 receive_seq=9988 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998741 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.2 th1: temp=53.4 th2: temp=58.4 th3: temp=56.3 sysload=0.36 cputime=379.959 memavail=7394552 print_time=5291.027 buffer_time=2.116 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 114 Hz
Stats 5267.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24050150 bytes_read=3720119 bytes_retransmit=9 bytes_invalid=0 send_seq=451436 receive_seq=451436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=23610 freq=400015891 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32746 bytes_read=102845 bytes_retransmit=0 bytes_invalid=0 send_seq=5429 receive_seq=5429 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997383 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=166851 bytes_read=5214988 bytes_retransmit=9 bytes_invalid=0 send_seq=22979 receive_seq=22979 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997917 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93135 bytes_read=2097937 bytes_retransmit=9 bytes_invalid=0 send_seq=12549 receive_seq=12549 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997624 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33013 bytes_read=1343797 bytes_retransmit=9 bytes_invalid=0 send_seq=5443 receive_seq=5443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997777 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33499 bytes_read=100843 bytes_retransmit=9 bytes_invalid=0 send_seq=5430 receive_seq=5430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999466 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87591 bytes_read=2102285 bytes_retransmit=0 bytes_invalid=0 send_seq=9989 receive_seq=9989 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998744 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.6 th1: temp=53.5 th2: temp=58.4 th3: temp=56.5 sysload=0.36 cputime=380.128 memavail=7393800 print_time=5292.224 buffer_time=2.311 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 115 Hz
Stats 5268.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24065749 bytes_read=3721774 bytes_retransmit=9 bytes_invalid=0 send_seq=451705 receive_seq=451705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=35 upcoming_bytes=20471 freq=400015874 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32752 bytes_read=102861 bytes_retransmit=0 bytes_invalid=0 send_seq=5430 receive_seq=5430 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997389 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=166927 bytes_read=5218061 bytes_retransmit=9 bytes_invalid=0 send_seq=22990 receive_seq=22990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997837 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93141 bytes_read=2098051 bytes_retransmit=9 bytes_invalid=0 send_seq=12550 receive_seq=12550 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997603 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33019 bytes_read=1344061 bytes_retransmit=9 bytes_invalid=0 send_seq=5444 receive_seq=5444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997763 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33505 bytes_read=100859 bytes_retransmit=9 bytes_invalid=0 send_seq=5431 receive_seq=5431 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999495 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87597 bytes_read=2102641 bytes_retransmit=0 bytes_invalid=0 send_seq=9990 receive_seq=9990 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998779 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.8 th1: temp=53.5 th2: temp=58.6 th3: temp=56.4 sysload=0.36 cputime=380.278 memavail=7393800 print_time=5293.095 buffer_time=2.181 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 116 Hz
Stats 5269.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24079595 bytes_read=3723284 bytes_retransmit=9 bytes_invalid=0 send_seq=451945 receive_seq=451945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=22547 freq=400015861 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=32758 bytes_read=102890 bytes_retransmit=0 bytes_invalid=0 send_seq=5431 receive_seq=5431 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997389 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=167003 bytes_read=5221123 bytes_retransmit=9 bytes_invalid=0 send_seq=23001 receive_seq=23001 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997917 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93147 bytes_read=2098151 bytes_retransmit=9 bytes_invalid=0 send_seq=12551 receive_seq=12551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997675 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33025 bytes_read=1344295 bytes_retransmit=9 bytes_invalid=0 send_seq=5445 receive_seq=5445 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997773 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33511 bytes_read=100875 bytes_retransmit=9 bytes_invalid=0 send_seq=5432 receive_seq=5432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999499 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87603 bytes_read=2102997 bytes_retransmit=0 bytes_invalid=0 send_seq=9991 receive_seq=9991 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998780 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=53.6 th1: temp=53.4 th2: temp=58.5 th3: temp=56.5 sysload=0.36 cputime=380.424 memavail=7393816 print_time=5294.031 buffer_time=2.116 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 117 Hz
Stats 5270.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24096533 bytes_read=3725073 bytes_retransmit=9 bytes_invalid=0 send_seq=452235 receive_seq=452235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=24124 freq=400015848 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=32764 bytes_read=102906 bytes_retransmit=0 bytes_invalid=0 send_seq=5432 receive_seq=5432 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997412 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=167079 bytes_read=5224267 bytes_retransmit=9 bytes_invalid=0 send_seq=23012 receive_seq=23012 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997893 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93153 bytes_read=2098279 bytes_retransmit=9 bytes_invalid=0 send_seq=12552 receive_seq=12552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997684 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33031 bytes_read=1344574 bytes_retransmit=9 bytes_invalid=0 send_seq=5446 receive_seq=5446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997771 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33517 bytes_read=100891 bytes_retransmit=9 bytes_invalid=0 send_seq=5433 receive_seq=5433 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999492 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87609 bytes_read=2103353 bytes_retransmit=0 bytes_invalid=0 send_seq=9992 receive_seq=9992 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998802 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=53.6 th1: temp=53.4 th2: temp=58.4 th3: temp=56.2 sysload=0.33 cputime=380.590 memavail=7393816 print_time=5295.229 buffer_time=2.315 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 118 Hz
Stats 5271.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24112532 bytes_read=3726762 bytes_retransmit=9 bytes_invalid=0 send_seq=452509 receive_seq=452509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=20704 freq=400015924 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=32770 bytes_read=102922 bytes_retransmit=0 bytes_invalid=0 send_seq=5433 receive_seq=5433 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997386 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=167155 bytes_read=5227325 bytes_retransmit=9 bytes_invalid=0 send_seq=23023 receive_seq=23023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997835 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93159 bytes_read=2098379 bytes_retransmit=9 bytes_invalid=0 send_seq=12553 receive_seq=12553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997703 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33037 bytes_read=1344823 bytes_retransmit=9 bytes_invalid=0 send_seq=5447 receive_seq=5447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997810 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33523 bytes_read=100907 bytes_retransmit=9 bytes_invalid=0 send_seq=5434 receive_seq=5434 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999479 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87615 bytes_read=2103709 bytes_retransmit=0 bytes_invalid=0 send_seq=9993 receive_seq=9993 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998768 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=53.3 th1: temp=53.3 th2: temp=58.6 th3: temp=56.2 sysload=0.33 cputime=380.751 memavail=7393792 print_time=5296.106 buffer_time=2.190 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 119 Hz
Stats 5272.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24126656 bytes_read=3728297 bytes_retransmit=9 bytes_invalid=0 send_seq=452755 receive_seq=452754 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=22 upcoming_bytes=22616 freq=400015895 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=32776 bytes_read=102938 bytes_retransmit=0 bytes_invalid=0 send_seq=5434 receive_seq=5434 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997261 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=167231 bytes_read=5230382 bytes_retransmit=9 bytes_invalid=0 send_seq=23034 receive_seq=23034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997655 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93165 bytes_read=2098479 bytes_retransmit=9 bytes_invalid=0 send_seq=12554 receive_seq=12554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33043 bytes_read=1345057 bytes_retransmit=9 bytes_invalid=0 send_seq=5448 receive_seq=5448 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997715 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33529 bytes_read=100934 bytes_retransmit=9 bytes_invalid=0 send_seq=5435 receive_seq=5435 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87621 bytes_read=2104049 bytes_retransmit=0 bytes_invalid=0 send_seq=9994 receive_seq=9994 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998726 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=53.8 th1: temp=53.2 th2: temp=58.5 th3: temp=56.3 sysload=0.33 cputime=380.896 memavail=7393724 print_time=5297.034 buffer_time=2.118 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 120 Hz
Stats 5273.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24143501 bytes_read=3730091 bytes_retransmit=9 bytes_invalid=0 send_seq=453045 receive_seq=453045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=35 upcoming_bytes=24380 freq=400015886 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=32782 bytes_read=102954 bytes_retransmit=0 bytes_invalid=0 send_seq=5435 receive_seq=5435 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997301 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=167300 bytes_read=5233466 bytes_retransmit=9 bytes_invalid=0 send_seq=23044 receive_seq=23044 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997695 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=93171 bytes_read=2098621 bytes_retransmit=9 bytes_invalid=0 send_seq=12555 receive_seq=12555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997564 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33049 bytes_read=1345351 bytes_retransmit=9 bytes_invalid=0 send_seq=5449 receive_seq=5449 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997739 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33535 bytes_read=100950 bytes_retransmit=9 bytes_invalid=0 send_seq=5436 receive_seq=5436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999453 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87627 bytes_read=2104405 bytes_retransmit=0 bytes_invalid=0 send_seq=9995 receive_seq=9995 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998731 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=53.7 th1: temp=53.7 th2: temp=58.5 th3: temp=56.4 sysload=0.33 cputime=381.061 memavail=7393724 print_time=5298.230 buffer_time=2.311 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 121 Hz
Stats 5274.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24159741 bytes_read=3731786 bytes_retransmit=9 bytes_invalid=0 send_seq=453322 receive_seq=453322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=20915 freq=400015982 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32788 bytes_read=102983 bytes_retransmit=0 bytes_invalid=0 send_seq=5436 receive_seq=5436 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997302 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=167376 bytes_read=5236523 bytes_retransmit=9 bytes_invalid=0 send_seq=23055 receive_seq=23055 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997702 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=93177 bytes_read=2098721 bytes_retransmit=9 bytes_invalid=0 send_seq=12556 receive_seq=12556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997556 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33055 bytes_read=1345600 bytes_retransmit=9 bytes_invalid=0 send_seq=5450 receive_seq=5450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997717 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33541 bytes_read=100966 bytes_retransmit=9 bytes_invalid=0 send_seq=5437 receive_seq=5437 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87633 bytes_read=2104761 bytes_retransmit=0 bytes_invalid=0 send_seq=9996 receive_seq=9996 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998716 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=53.7 th1: temp=53.9 th2: temp=58.5 th3: temp=56.3 sysload=0.33 cputime=381.290 memavail=7393724 print_time=5299.109 buffer_time=2.190 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 122 Hz
Stats 5275.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24173753 bytes_read=3733291 bytes_retransmit=9 bytes_invalid=0 send_seq=453561 receive_seq=453561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=46 upcoming_bytes=23091 freq=400015958 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32794 bytes_read=102999 bytes_retransmit=0 bytes_invalid=0 send_seq=5437 receive_seq=5437 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997162 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=167452 bytes_read=5239580 bytes_retransmit=9 bytes_invalid=0 send_seq=23066 receive_seq=23066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997518 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=93183 bytes_read=2098821 bytes_retransmit=9 bytes_invalid=0 send_seq=12557 receive_seq=12557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997374 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33061 bytes_read=1345834 bytes_retransmit=9 bytes_invalid=0 send_seq=5451 receive_seq=5451 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997568 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33547 bytes_read=100982 bytes_retransmit=9 bytes_invalid=0 send_seq=5438 receive_seq=5438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999415 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87639 bytes_read=2105117 bytes_retransmit=0 bytes_invalid=0 send_seq=9997 receive_seq=9997 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998624 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=53.7 th1: temp=53.5 th2: temp=58.5 th3: temp=56.3 sysload=0.30 cputime=381.434 memavail=7393724 print_time=5300.034 buffer_time=2.114 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 123 Hz
Stats 5276.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24190826 bytes_read=3735111 bytes_retransmit=9 bytes_invalid=0 send_seq=453854 receive_seq=453854 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=25059 freq=400015937 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32800 bytes_read=103015 bytes_retransmit=0 bytes_invalid=0 send_seq=5438 receive_seq=5438 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997212 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=167528 bytes_read=5242664 bytes_retransmit=9 bytes_invalid=0 send_seq=23077 receive_seq=23077 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997643 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=93189 bytes_read=2098949 bytes_retransmit=9 bytes_invalid=0 send_seq=12558 receive_seq=12558 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997417 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33067 bytes_read=1346113 bytes_retransmit=9 bytes_invalid=0 send_seq=5452 receive_seq=5452 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997611 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33553 bytes_read=100998 bytes_retransmit=9 bytes_invalid=0 send_seq=5439 receive_seq=5439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87645 bytes_read=2105473 bytes_retransmit=0 bytes_invalid=0 send_seq=9998 receive_seq=9998 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998638 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=53.6 th1: temp=53.5 th2: temp=58.6 th3: temp=56.2 sysload=0.30 cputime=381.603 memavail=7393756 print_time=5301.235 buffer_time=2.315 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 124 Hz
Stats 5277.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24207409 bytes_read=3736836 bytes_retransmit=9 bytes_invalid=0 send_seq=454137 receive_seq=454137 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=21362 freq=400015909 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32806 bytes_read=103031 bytes_retransmit=0 bytes_invalid=0 send_seq=5439 receive_seq=5439 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997255 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=167604 bytes_read=5245779 bytes_retransmit=9 bytes_invalid=0 send_seq=23088 receive_seq=23088 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997683 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=93195 bytes_read=2099049 bytes_retransmit=9 bytes_invalid=0 send_seq=12559 receive_seq=12559 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997468 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33073 bytes_read=1346362 bytes_retransmit=9 bytes_invalid=0 send_seq=5453 receive_seq=5453 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33559 bytes_read=101025 bytes_retransmit=9 bytes_invalid=0 send_seq=5440 receive_seq=5440 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87651 bytes_read=2105829 bytes_retransmit=0 bytes_invalid=0 send_seq=9999 receive_seq=9999 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998654 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=53.7 th1: temp=53.5 th2: temp=58.7 th3: temp=56.6 sysload=0.30 cputime=381.761 memavail=7393012 print_time=5302.109 buffer_time=2.189 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 125 Hz
Stats 5278.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24221672 bytes_read=3738381 bytes_retransmit=9 bytes_invalid=0 send_seq=454384 receive_seq=454384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=23407 freq=400015880 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32812 bytes_read=103047 bytes_retransmit=0 bytes_invalid=0 send_seq=5440 receive_seq=5440 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997301 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=167680 bytes_read=5248840 bytes_retransmit=9 bytes_invalid=0 send_seq=23099 receive_seq=23099 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997727 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93201 bytes_read=2099156 bytes_retransmit=9 bytes_invalid=0 send_seq=12560 receive_seq=12560 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997515 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33079 bytes_read=1346611 bytes_retransmit=9 bytes_invalid=0 send_seq=5454 receive_seq=5454 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997679 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33565 bytes_read=101041 bytes_retransmit=9 bytes_invalid=0 send_seq=5441 receive_seq=5441 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87657 bytes_read=2106185 bytes_retransmit=0 bytes_invalid=0 send_seq=10000 receive_seq=10000 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998670 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=53.7 th1: temp=53.5 th2: temp=58.6 th3: temp=56.0 sysload=0.30 cputime=381.915 memavail=7393012 print_time=5303.039 buffer_time=2.118 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 126 Hz
Stats 5279.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24239106 bytes_read=3740215 bytes_retransmit=9 bytes_invalid=0 send_seq=454683 receive_seq=454683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=25043 freq=400015862 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32818 bytes_read=103076 bytes_retransmit=0 bytes_invalid=0 send_seq=5441 receive_seq=5441 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997339 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=167749 bytes_read=5251886 bytes_retransmit=9 bytes_invalid=0 send_seq=23109 receive_seq=23109 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997754 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93207 bytes_read=2099275 bytes_retransmit=9 bytes_invalid=0 send_seq=12561 receive_seq=12561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997577 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33085 bytes_read=1346905 bytes_retransmit=9 bytes_invalid=0 send_seq=5455 receive_seq=5455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997721 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33571 bytes_read=101057 bytes_retransmit=9 bytes_invalid=0 send_seq=5442 receive_seq=5442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87663 bytes_read=2106541 bytes_retransmit=0 bytes_invalid=0 send_seq=10001 receive_seq=10001 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998688 coil_temp=17.1 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=53.6 th1: temp=53.6 th2: temp=58.7 th3: temp=56.3 sysload=0.30 cputime=382.095 memavail=7393012 print_time=5304.239 buffer_time=2.312 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 127 Hz
Stats 5280.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24255750 bytes_read=3741955 bytes_retransmit=9 bytes_invalid=0 send_seq=454969 receive_seq=454969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=21269 freq=400015853 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32824 bytes_read=103092 bytes_retransmit=0 bytes_invalid=0 send_seq=5442 receive_seq=5442 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997333 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=167825 bytes_read=5254928 bytes_retransmit=9 bytes_invalid=0 send_seq=23120 receive_seq=23120 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997767 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93213 bytes_read=2099368 bytes_retransmit=9 bytes_invalid=0 send_seq=12562 receive_seq=12562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997575 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33091 bytes_read=1347139 bytes_retransmit=9 bytes_invalid=0 send_seq=5456 receive_seq=5456 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997719 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33577 bytes_read=101073 bytes_retransmit=9 bytes_invalid=0 send_seq=5443 receive_seq=5443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87669 bytes_read=2106897 bytes_retransmit=0 bytes_invalid=0 send_seq=10002 receive_seq=10002 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998693 coil_temp=17.1 refs=0 mcu_temp=20.32 supply_voltage=3.012 th0: temp=53.4 th1: temp=53.5 th2: temp=58.4 th3: temp=56.3 sysload=0.28 cputime=382.252 memavail=7393012 print_time=5305.113 buffer_time=2.184 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 128 Hz
Stats 5281.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24269962 bytes_read=3743516 bytes_retransmit=9 bytes_invalid=0 send_seq=455216 receive_seq=455216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=23563 freq=400015844 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32830 bytes_read=103108 bytes_retransmit=0 bytes_invalid=0 send_seq=5443 receive_seq=5443 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997339 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=167901 bytes_read=5257969 bytes_retransmit=9 bytes_invalid=0 send_seq=23131 receive_seq=23131 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997775 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93219 bytes_read=2099461 bytes_retransmit=9 bytes_invalid=0 send_seq=12563 receive_seq=12563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997581 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33097 bytes_read=1347373 bytes_retransmit=9 bytes_invalid=0 send_seq=5457 receive_seq=5457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997727 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33583 bytes_read=101089 bytes_retransmit=9 bytes_invalid=0 send_seq=5444 receive_seq=5444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87675 bytes_read=2107253 bytes_retransmit=0 bytes_invalid=0 send_seq=10003 receive_seq=10003 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998691 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.012 th0: temp=53.6 th1: temp=53.6 th2: temp=58.6 th3: temp=56.3 sysload=0.28 cputime=382.400 memavail=7393012 print_time=5306.040 buffer_time=2.111 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 129 Hz
Stats 5282.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24287444 bytes_read=3745330 bytes_retransmit=9 bytes_invalid=0 send_seq=455513 receive_seq=455512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=25458 freq=400015829 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32836 bytes_read=103124 bytes_retransmit=0 bytes_invalid=0 send_seq=5444 receive_seq=5444 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997340 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=167977 bytes_read=5261104 bytes_retransmit=9 bytes_invalid=0 send_seq=23142 receive_seq=23142 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997758 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93225 bytes_read=2099586 bytes_retransmit=9 bytes_invalid=0 send_seq=12564 receive_seq=12564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997638 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33103 bytes_read=1347667 bytes_retransmit=9 bytes_invalid=0 send_seq=5458 receive_seq=5458 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997722 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33589 bytes_read=101116 bytes_retransmit=9 bytes_invalid=0 send_seq=5445 receive_seq=5445 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999454 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87681 bytes_read=2107609 bytes_retransmit=0 bytes_invalid=0 send_seq=10004 receive_seq=10004 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998726 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.7 th1: temp=53.4 th2: temp=58.5 th3: temp=56.3 sysload=0.28 cputime=382.573 memavail=7393024 print_time=5307.244 buffer_time=2.309 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 130 Hz
Stats 5283.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24304317 bytes_read=3747085 bytes_retransmit=9 bytes_invalid=0 send_seq=455801 receive_seq=455801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=52 upcoming_bytes=21379 freq=400015812 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32842 bytes_read=103140 bytes_retransmit=0 bytes_invalid=0 send_seq=5445 receive_seq=5445 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997334 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=168053 bytes_read=5264177 bytes_retransmit=9 bytes_invalid=0 send_seq=23153 receive_seq=23153 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997750 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93231 bytes_read=2099686 bytes_retransmit=9 bytes_invalid=0 send_seq=12565 receive_seq=12565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997695 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33109 bytes_read=1347916 bytes_retransmit=9 bytes_invalid=0 send_seq=5459 receive_seq=5459 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997727 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33595 bytes_read=101132 bytes_retransmit=9 bytes_invalid=0 send_seq=5446 receive_seq=5446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87687 bytes_read=2107965 bytes_retransmit=0 bytes_invalid=0 send_seq=10005 receive_seq=10005 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998722 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.5 th1: temp=53.5 th2: temp=58.8 th3: temp=56.3 sysload=0.28 cputime=382.725 memavail=7393024 print_time=5308.116 buffer_time=2.180 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 131 Hz
Stats 5284.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24318567 bytes_read=3748615 bytes_retransmit=9 bytes_invalid=0 send_seq=456045 receive_seq=456045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=23933 freq=400015806 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32848 bytes_read=103169 bytes_retransmit=0 bytes_invalid=0 send_seq=5446 receive_seq=5446 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997346 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=168129 bytes_read=5267234 bytes_retransmit=9 bytes_invalid=0 send_seq=23164 receive_seq=23164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000254 adj=63998053 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=93237 bytes_read=2099800 bytes_retransmit=9 bytes_invalid=0 send_seq=12566 receive_seq=12566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997688 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33115 bytes_read=1348150 bytes_retransmit=9 bytes_invalid=0 send_seq=5460 receive_seq=5460 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997741 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33601 bytes_read=101148 bytes_retransmit=9 bytes_invalid=0 send_seq=5447 receive_seq=5447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.8 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87693 bytes_read=2108321 bytes_retransmit=0 bytes_invalid=0 send_seq=10006 receive_seq=10006 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998727 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.6 th1: temp=53.5 th2: temp=58.5 th3: temp=56.3 sysload=0.28 cputime=382.872 memavail=7393024 print_time=5309.042 buffer_time=2.105 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 132 Hz
Stats 5285.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24335984 bytes_read=3750424 bytes_retransmit=9 bytes_invalid=0 send_seq=456339 receive_seq=456339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=26016 freq=400015804 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32854 bytes_read=103185 bytes_retransmit=0 bytes_invalid=0 send_seq=5447 receive_seq=5447 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997339 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=168205 bytes_read=5270319 bytes_retransmit=9 bytes_invalid=0 send_seq=23175 receive_seq=23175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000257 adj=63998297 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=93243 bytes_read=2099928 bytes_retransmit=9 bytes_invalid=0 send_seq=12567 receive_seq=12567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997680 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33121 bytes_read=1348444 bytes_retransmit=9 bytes_invalid=0 send_seq=5461 receive_seq=5461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997742 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33607 bytes_read=101164 bytes_retransmit=9 bytes_invalid=0 send_seq=5448 receive_seq=5448 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999470 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87699 bytes_read=2108677 bytes_retransmit=0 bytes_invalid=0 send_seq=10007 receive_seq=10007 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998756 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.012 th0: temp=53.4 th1: temp=53.7 th2: temp=58.6 th3: temp=56.3 sysload=0.26 cputime=383.043 memavail=7393024 print_time=5310.246 buffer_time=2.309 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Stats 5286.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24353341 bytes_read=3752245 bytes_retransmit=9 bytes_invalid=0 send_seq=456638 receive_seq=456638 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=20573 freq=400015801 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32860 bytes_read=103201 bytes_retransmit=0 bytes_invalid=0 send_seq=5448 receive_seq=5448 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997314 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=168281 bytes_read=5273375 bytes_retransmit=9 bytes_invalid=0 send_seq=23186 receive_seq=23186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000253 adj=63998162 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=93249 bytes_read=2100028 bytes_retransmit=9 bytes_invalid=0 send_seq=12568 receive_seq=12568 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997641 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33127 bytes_read=1348678 bytes_retransmit=9 bytes_invalid=0 send_seq=5462 receive_seq=5462 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997731 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33613 bytes_read=101180 bytes_retransmit=9 bytes_invalid=0 send_seq=5449 receive_seq=5449 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87705 bytes_read=2109033 bytes_retransmit=0 bytes_invalid=0 send_seq=10008 receive_seq=10008 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998738 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.012 th0: temp=53.7 th1: temp=53.6 th2: temp=58.8 th3: temp=56.4 sysload=0.26 cputime=383.182 memavail=7393036 print_time=5310.894 buffer_time=1.956 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5287.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24367885 bytes_read=3753820 bytes_retransmit=9 bytes_invalid=0 send_seq=456891 receive_seq=456891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=7518 freq=400015782 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32866 bytes_read=103217 bytes_retransmit=0 bytes_invalid=0 send_seq=5449 receive_seq=5449 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997312 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=168357 bytes_read=5276494 bytes_retransmit=9 bytes_invalid=0 send_seq=23197 receive_seq=23197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000258 adj=63998121 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=93255 bytes_read=2100128 bytes_retransmit=9 bytes_invalid=0 send_seq=12569 receive_seq=12569 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997883 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33133 bytes_read=1348912 bytes_retransmit=9 bytes_invalid=0 send_seq=5463 receive_seq=5463 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997730 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33619 bytes_read=101207 bytes_retransmit=9 bytes_invalid=0 send_seq=5450 receive_seq=5450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999476 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87711 bytes_read=2109389 bytes_retransmit=0 bytes_invalid=0 send_seq=10009 receive_seq=10009 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998733 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.8 th1: temp=53.6 th2: temp=58.6 th3: temp=56.3 sysload=0.26 cputime=383.272 memavail=7395620 print_time=5310.894 buffer_time=0.955 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5288.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24376353 bytes_read=3754919 bytes_retransmit=9 bytes_invalid=0 send_seq=457043 receive_seq=457043 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015890 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32872 bytes_read=103233 bytes_retransmit=0 bytes_invalid=0 send_seq=5450 receive_seq=5450 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997360 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=168433 bytes_read=5279595 bytes_retransmit=9 bytes_invalid=0 send_seq=23208 receive_seq=23208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000255 adj=63998226 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=93261 bytes_read=2100256 bytes_retransmit=9 bytes_invalid=0 send_seq=12570 receive_seq=12570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997899 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33139 bytes_read=1349221 bytes_retransmit=9 bytes_invalid=0 send_seq=5464 receive_seq=5464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997756 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33625 bytes_read=101223 bytes_retransmit=9 bytes_invalid=0 send_seq=5451 receive_seq=5451 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999490 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87717 bytes_read=2109745 bytes_retransmit=0 bytes_invalid=0 send_seq=10010 receive_seq=10010 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998744 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.9 th1: temp=53.6 th2: temp=58.7 th3: temp=56.3 sysload=0.26 cputime=383.361 memavail=7388844 print_time=5310.894 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
LIS2DW finished 'toolboard_t0' measurements
Resonances data written to /tmp/resonances_y_250.000_250.000_20.000_t0.csv file
RatOS | IDEX:: Selecting T1..
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 20.000000
RatOS | IDEX:: Toolhead offset applied for T1: X=-0.0 Y=-0.0 Z=-0.0
Activating extruder extruder1
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
Probing point (250.000, 250.000, 20.000)
Stats 5289.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24379939 bytes_read=3755609 bytes_retransmit=9 bytes_invalid=0 send_seq=457119 receive_seq=457119 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015885 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32878 bytes_read=103262 bytes_retransmit=0 bytes_invalid=0 send_seq=5451 receive_seq=5451 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997184 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=168494 bytes_read=5279937 bytes_retransmit=9 bytes_invalid=0 send_seq=23215 receive_seq=23215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000256 adj=63997960 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93267 bytes_read=2100370 bytes_retransmit=9 bytes_invalid=0 send_seq=12571 receive_seq=12571 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997643 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33145 bytes_read=1349455 bytes_retransmit=9 bytes_invalid=0 send_seq=5465 receive_seq=5465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997593 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33631 bytes_read=101239 bytes_retransmit=9 bytes_invalid=0 send_seq=5452 receive_seq=5452 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999447 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87723 bytes_read=2110101 bytes_retransmit=0 bytes_invalid=0 send_seq=10011 receive_seq=10011 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998631 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.6 th1: temp=53.6 th2: temp=58.7 th3: temp=56.4 sysload=0.26 cputime=383.527 memavail=7397396 print_time=5312.565 buffer_time=0.625 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t1' measurements
toolhead: max_velocity: 600.000000
max_accel: 8379.841000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance testing
Testing frequency 10 Hz
Testing frequency 11 Hz
Testing frequency 12 Hz
Stats 5290.3: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24382563 bytes_read=3756224 bytes_retransmit=9 bytes_invalid=0 send_seq=457180 receive_seq=457180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015867 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32884 bytes_read=103278 bytes_retransmit=0 bytes_invalid=0 send_seq=5452 receive_seq=5452 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997277 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=168500 bytes_read=5280037 bytes_retransmit=9 bytes_invalid=0 send_seq=23216 receive_seq=23216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000251 adj=63997945 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93394 bytes_read=2101378 bytes_retransmit=9 bytes_invalid=0 send_seq=12585 receive_seq=12585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997610 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33151 bytes_read=1349689 bytes_retransmit=9 bytes_invalid=0 send_seq=5466 receive_seq=5466 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997608 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33637 bytes_read=101255 bytes_retransmit=9 bytes_invalid=0 send_seq=5453 receive_seq=5453 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87729 bytes_read=2110457 bytes_retransmit=0 bytes_invalid=0 send_seq=10012 receive_seq=10012 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998648 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.6 th1: temp=53.6 th2: temp=58.5 th3: temp=56.4 sysload=0.24 cputime=383.687 memavail=7397396 print_time=5315.782 buffer_time=2.841 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5291.3: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24383049 bytes_read=3756709 bytes_retransmit=9 bytes_invalid=0 send_seq=457206 receive_seq=457206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015847 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32890 bytes_read=103294 bytes_retransmit=0 bytes_invalid=0 send_seq=5453 receive_seq=5453 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997301 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=168506 bytes_read=5280165 bytes_retransmit=9 bytes_invalid=0 send_seq=23217 receive_seq=23217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000247 adj=63997727 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93470 bytes_read=2104405 bytes_retransmit=9 bytes_invalid=0 send_seq=12596 receive_seq=12596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997533 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33157 bytes_read=1349983 bytes_retransmit=9 bytes_invalid=0 send_seq=5467 receive_seq=5467 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33643 bytes_read=101271 bytes_retransmit=9 bytes_invalid=0 send_seq=5454 receive_seq=5454 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999447 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87735 bytes_read=2110813 bytes_retransmit=0 bytes_invalid=0 send_seq=10013 receive_seq=10013 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998671 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.9 th1: temp=53.8 th2: temp=58.7 th3: temp=56.4 sysload=0.24 cputime=383.752 memavail=7397144 print_time=5316.043 buffer_time=2.101 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 13 Hz
Stats 5292.3: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24384376 bytes_read=3757207 bytes_retransmit=9 bytes_invalid=0 send_seq=457244 receive_seq=457244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015834 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32896 bytes_read=103310 bytes_retransmit=0 bytes_invalid=0 send_seq=5454 receive_seq=5454 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997324 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=168512 bytes_read=5280265 bytes_retransmit=9 bytes_invalid=0 send_seq=23218 receive_seq=23218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000243 adj=63997715 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93546 bytes_read=2107417 bytes_retransmit=9 bytes_invalid=0 send_seq=12607 receive_seq=12607 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997545 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33163 bytes_read=1350217 bytes_retransmit=9 bytes_invalid=0 send_seq=5468 receive_seq=5468 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33649 bytes_read=101298 bytes_retransmit=9 bytes_invalid=0 send_seq=5455 receive_seq=5455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87741 bytes_read=2111169 bytes_retransmit=0 bytes_invalid=0 send_seq=10014 receive_seq=10014 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998676 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.6 th1: temp=53.9 th2: temp=58.8 th3: temp=56.3 sysload=0.24 cputime=383.823 memavail=7397144 print_time=5316.962 buffer_time=2.020 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 14 Hz
Stats 5293.3: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24386100 bytes_read=3757739 bytes_retransmit=9 bytes_invalid=0 send_seq=457289 receive_seq=457289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=400015813 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32902 bytes_read=103326 bytes_retransmit=0 bytes_invalid=0 send_seq=5455 receive_seq=5455 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997335 toolboard_t0: mcu_awake=0.044 mcu_task_avg=0.000086 mcu_task_stddev=0.000074 bytes_write=168518 bytes_read=5280381 bytes_retransmit=9 bytes_invalid=0 send_seq=23219 receive_seq=23219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997699 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=93622 bytes_read=2110475 bytes_retransmit=9 bytes_invalid=0 send_seq=12618 receive_seq=12618 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997546 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33169 bytes_read=1350466 bytes_retransmit=9 bytes_invalid=0 send_seq=5469 receive_seq=5469 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997690 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33655 bytes_read=101314 bytes_retransmit=9 bytes_invalid=0 send_seq=5456 receive_seq=5456 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87747 bytes_read=2111525 bytes_retransmit=0 bytes_invalid=0 send_seq=10015 receive_seq=10015 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998681 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.9 th1: temp=54.0 th2: temp=58.7 th3: temp=56.4 sysload=0.24 cputime=383.898 memavail=7397148 print_time=5318.217 buffer_time=2.275 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 15 Hz
Stats 5294.3: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24387399 bytes_read=3758263 bytes_retransmit=9 bytes_invalid=0 send_seq=457326 receive_seq=457326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015815 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32908 bytes_read=103355 bytes_retransmit=0 bytes_invalid=0 send_seq=5456 receive_seq=5456 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997360 toolboard_t0: mcu_awake=0.044 mcu_task_avg=0.000086 mcu_task_stddev=0.000074 bytes_write=168524 bytes_read=5280509 bytes_retransmit=9 bytes_invalid=0 send_seq=23220 receive_seq=23220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997705 toolboard_t1: mcu_awake=0.220 mcu_task_avg=0.000115 mcu_task_stddev=0.000070 bytes_write=93698 bytes_read=2113576 bytes_retransmit=9 bytes_invalid=0 send_seq=12629 receive_seq=12629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997555 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33175 bytes_read=1350760 bytes_retransmit=9 bytes_invalid=0 send_seq=5470 receive_seq=5470 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997710 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33661 bytes_read=101330 bytes_retransmit=9 bytes_invalid=0 send_seq=5457 receive_seq=5457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87753 bytes_read=2111881 bytes_retransmit=0 bytes_invalid=0 send_seq=10016 receive_seq=10016 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998700 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.6 th1: temp=54.0 th2: temp=58.9 th3: temp=56.5 sysload=0.24 cputime=383.972 memavail=7397148 print_time=5319.136 buffer_time=2.193 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 16 Hz
Stats 5295.3: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24388885 bytes_read=3758778 bytes_retransmit=9 bytes_invalid=0 send_seq=457367 receive_seq=457367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015798 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32914 bytes_read=103371 bytes_retransmit=0 bytes_invalid=0 send_seq=5457 receive_seq=5457 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997345 toolboard_t0: mcu_awake=0.044 mcu_task_avg=0.000086 mcu_task_stddev=0.000074 bytes_write=168530 bytes_read=5280609 bytes_retransmit=9 bytes_invalid=0 send_seq=23221 receive_seq=23221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997659 toolboard_t1: mcu_awake=0.220 mcu_task_avg=0.000115 mcu_task_stddev=0.000070 bytes_write=93774 bytes_read=2116633 bytes_retransmit=9 bytes_invalid=0 send_seq=12640 receive_seq=12640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33181 bytes_read=1350994 bytes_retransmit=9 bytes_invalid=0 send_seq=5471 receive_seq=5471 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997703 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33667 bytes_read=101346 bytes_retransmit=9 bytes_invalid=0 send_seq=5458 receive_seq=5458 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87759 bytes_read=2112237 bytes_retransmit=0 bytes_invalid=0 send_seq=10017 receive_seq=10017 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998682 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.8 th1: temp=54.1 th2: temp=58.7 th3: temp=56.6 sysload=0.22 cputime=384.043 memavail=7397148 print_time=5320.019 buffer_time=2.076 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 17 Hz
Stats 5296.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24390196 bytes_read=3759283 bytes_retransmit=9 bytes_invalid=0 send_seq=457403 receive_seq=457403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015790 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32920 bytes_read=103387 bytes_retransmit=0 bytes_invalid=0 send_seq=5458 receive_seq=5458 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997358 toolboard_t0: mcu_awake=0.044 mcu_task_avg=0.000086 mcu_task_stddev=0.000074 bytes_write=168536 bytes_read=5280709 bytes_retransmit=9 bytes_invalid=0 send_seq=23222 receive_seq=23222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997669 toolboard_t1: mcu_awake=0.220 mcu_task_avg=0.000115 mcu_task_stddev=0.000070 bytes_write=93850 bytes_read=2119690 bytes_retransmit=9 bytes_invalid=0 send_seq=12651 receive_seq=12651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33187 bytes_read=1351228 bytes_retransmit=9 bytes_invalid=0 send_seq=5472 receive_seq=5472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997715 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33673 bytes_read=101362 bytes_retransmit=9 bytes_invalid=0 send_seq=5459 receive_seq=5459 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87765 bytes_read=2112593 bytes_retransmit=0 bytes_invalid=0 send_seq=10018 receive_seq=10018 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998694 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.7 th1: temp=54.3 th2: temp=58.9 th3: temp=56.7 sysload=0.22 cputime=384.118 memavail=7397148 print_time=5320.944 buffer_time=2.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 18 Hz
Stats 5297.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24392115 bytes_read=3759862 bytes_retransmit=9 bytes_invalid=0 send_seq=457451 receive_seq=457451 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015805 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32926 bytes_read=103403 bytes_retransmit=0 bytes_invalid=0 send_seq=5459 receive_seq=5459 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997346 toolboard_t0: mcu_awake=0.044 mcu_task_avg=0.000086 mcu_task_stddev=0.000074 bytes_write=168542 bytes_read=5280837 bytes_retransmit=9 bytes_invalid=0 send_seq=23223 receive_seq=23223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997653 toolboard_t1: mcu_awake=0.220 mcu_task_avg=0.000115 mcu_task_stddev=0.000070 bytes_write=93926 bytes_read=2122834 bytes_retransmit=9 bytes_invalid=0 send_seq=12662 receive_seq=12662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33193 bytes_read=1351522 bytes_retransmit=9 bytes_invalid=0 send_seq=5473 receive_seq=5473 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997712 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33679 bytes_read=101389 bytes_retransmit=9 bytes_invalid=0 send_seq=5460 receive_seq=5460 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87771 bytes_read=2112949 bytes_retransmit=0 bytes_invalid=0 send_seq=10019 receive_seq=10019 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998688 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=54.1 th1: temp=54.4 th2: temp=59.1 th3: temp=56.7 sysload=0.22 cputime=384.198 memavail=7396140 print_time=5322.232 buffer_time=2.289 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 19 Hz
Stats 5298.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24393838 bytes_read=3760392 bytes_retransmit=9 bytes_invalid=0 send_seq=457495 receive_seq=457495 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015808 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32932 bytes_read=103419 bytes_retransmit=0 bytes_invalid=0 send_seq=5460 receive_seq=5460 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997294 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=168548 bytes_read=5280951 bytes_retransmit=9 bytes_invalid=0 send_seq=23224 receive_seq=23224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997621 toolboard_t1: mcu_awake=0.220 mcu_task_avg=0.000115 mcu_task_stddev=0.000070 bytes_write=94002 bytes_read=2125893 bytes_retransmit=9 bytes_invalid=0 send_seq=12673 receive_seq=12673 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997599 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33199 bytes_read=1351771 bytes_retransmit=9 bytes_invalid=0 send_seq=5474 receive_seq=5474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33685 bytes_read=101405 bytes_retransmit=9 bytes_invalid=0 send_seq=5461 receive_seq=5461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87777 bytes_read=2113305 bytes_retransmit=0 bytes_invalid=0 send_seq=10020 receive_seq=10020 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998658 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=53.6 th1: temp=54.3 th2: temp=59.1 th3: temp=56.8 sysload=0.22 cputime=384.272 memavail=7396156 print_time=5323.084 buffer_time=2.139 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 20 Hz
Stats 5299.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24395307 bytes_read=3760907 bytes_retransmit=9 bytes_invalid=0 send_seq=457536 receive_seq=457536 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015801 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32938 bytes_read=103448 bytes_retransmit=0 bytes_invalid=0 send_seq=5461 receive_seq=5461 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997274 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=168554 bytes_read=5281051 bytes_retransmit=9 bytes_invalid=0 send_seq=23225 receive_seq=23225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997585 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94078 bytes_read=2128966 bytes_retransmit=9 bytes_invalid=0 send_seq=12684 receive_seq=12684 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997557 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33205 bytes_read=1352005 bytes_retransmit=9 bytes_invalid=0 send_seq=5475 receive_seq=5475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33691 bytes_read=101421 bytes_retransmit=9 bytes_invalid=0 send_seq=5462 receive_seq=5462 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87783 bytes_read=2113661 bytes_retransmit=0 bytes_invalid=0 send_seq=10021 receive_seq=10021 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998655 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=53.9 th1: temp=54.4 th2: temp=59.2 th3: temp=56.6 sysload=0.22 cputime=384.346 memavail=7396156 print_time=5324.041 buffer_time=2.095 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 21 Hz
Stats 5300.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24397310 bytes_read=3761491 bytes_retransmit=9 bytes_invalid=0 send_seq=457585 receive_seq=457585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=0 freq=400015808 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32944 bytes_read=103464 bytes_retransmit=0 bytes_invalid=0 send_seq=5462 receive_seq=5462 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997281 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=168560 bytes_read=5281179 bytes_retransmit=9 bytes_invalid=0 send_seq=23226 receive_seq=23226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997594 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94154 bytes_read=2132051 bytes_retransmit=9 bytes_invalid=0 send_seq=12695 receive_seq=12695 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997541 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33211 bytes_read=1352299 bytes_retransmit=9 bytes_invalid=0 send_seq=5476 receive_seq=5476 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33697 bytes_read=101437 bytes_retransmit=9 bytes_invalid=0 send_seq=5463 receive_seq=5463 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87789 bytes_read=2114017 bytes_retransmit=0 bytes_invalid=0 send_seq=10022 receive_seq=10022 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998662 coil_temp=17.0 refs=0 mcu_temp=20.34 supply_voltage=3.011 th0: temp=53.9 th1: temp=54.5 th2: temp=59.1 th3: temp=57.1 sysload=0.20 cputime=384.426 memavail=7396156 print_time=5325.243 buffer_time=2.298 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 22 Hz
Stats 5301.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24399119 bytes_read=3762041 bytes_retransmit=9 bytes_invalid=0 send_seq=457630 receive_seq=457630 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015791 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32950 bytes_read=103480 bytes_retransmit=0 bytes_invalid=0 send_seq=5463 receive_seq=5463 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997265 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=168566 bytes_read=5281279 bytes_retransmit=9 bytes_invalid=0 send_seq=23227 receive_seq=23227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997586 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94230 bytes_read=2135109 bytes_retransmit=9 bytes_invalid=0 send_seq=12706 receive_seq=12706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997503 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33217 bytes_read=1352533 bytes_retransmit=9 bytes_invalid=0 send_seq=5477 receive_seq=5477 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33703 bytes_read=101453 bytes_retransmit=9 bytes_invalid=0 send_seq=5464 receive_seq=5464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87795 bytes_read=2114373 bytes_retransmit=0 bytes_invalid=0 send_seq=10023 receive_seq=10023 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998671 coil_temp=17.0 refs=0 mcu_temp=20.34 supply_voltage=3.011 th0: temp=53.9 th1: temp=54.8 th2: temp=59.4 th3: temp=56.9 sysload=0.20 cputime=384.502 memavail=7396156 print_time=5326.120 buffer_time=2.173 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 23 Hz
Stats 5302.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24400716 bytes_read=3762580 bytes_retransmit=9 bytes_invalid=0 send_seq=457673 receive_seq=457673 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015783 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32956 bytes_read=103496 bytes_retransmit=0 bytes_invalid=0 send_seq=5464 receive_seq=5464 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997287 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=168572 bytes_read=5281379 bytes_retransmit=9 bytes_invalid=0 send_seq=23228 receive_seq=23228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997597 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94299 bytes_read=2138143 bytes_retransmit=9 bytes_invalid=0 send_seq=12716 receive_seq=12716 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997512 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33223 bytes_read=1352767 bytes_retransmit=9 bytes_invalid=0 send_seq=5478 receive_seq=5478 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997714 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33709 bytes_read=101480 bytes_retransmit=9 bytes_invalid=0 send_seq=5465 receive_seq=5465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999465 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87801 bytes_read=2114729 bytes_retransmit=0 bytes_invalid=0 send_seq=10024 receive_seq=10024 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998686 coil_temp=17.0 refs=0 mcu_temp=20.34 supply_voltage=3.011 th0: temp=53.8 th1: temp=54.8 th2: temp=59.5 th3: temp=57.0 sysload=0.20 cputime=384.581 memavail=7396156 print_time=5327.075 buffer_time=2.127 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 24 Hz
Stats 5303.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24402947 bytes_read=3763171 bytes_retransmit=9 bytes_invalid=0 send_seq=457727 receive_seq=457727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=0 freq=400015771 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32962 bytes_read=103512 bytes_retransmit=0 bytes_invalid=0 send_seq=5465 receive_seq=5465 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997296 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168578 bytes_read=5281521 bytes_retransmit=9 bytes_invalid=0 send_seq=23229 receive_seq=23229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997613 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94375 bytes_read=2141229 bytes_retransmit=9 bytes_invalid=0 send_seq=12727 receive_seq=12727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33229 bytes_read=1353076 bytes_retransmit=9 bytes_invalid=0 send_seq=5479 receive_seq=5479 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997713 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33715 bytes_read=101496 bytes_retransmit=9 bytes_invalid=0 send_seq=5466 receive_seq=5466 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87807 bytes_read=2115085 bytes_retransmit=0 bytes_invalid=0 send_seq=10025 receive_seq=10025 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998682 coil_temp=17.0 refs=0 mcu_temp=20.34 supply_voltage=3.011 th0: temp=53.7 th1: temp=54.7 th2: temp=59.5 th3: temp=57.2 sysload=0.20 cputime=384.667 memavail=7396192 print_time=5328.287 buffer_time=2.339 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 25 Hz
Stats 5304.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24404761 bytes_read=3763710 bytes_retransmit=9 bytes_invalid=0 send_seq=457773 receive_seq=457773 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015760 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32968 bytes_read=103541 bytes_retransmit=0 bytes_invalid=0 send_seq=5466 receive_seq=5466 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997299 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168584 bytes_read=5281621 bytes_retransmit=9 bytes_invalid=0 send_seq=23230 receive_seq=23230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997678 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94451 bytes_read=2144360 bytes_retransmit=9 bytes_invalid=0 send_seq=12738 receive_seq=12738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997518 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33235 bytes_read=1353310 bytes_retransmit=9 bytes_invalid=0 send_seq=5480 receive_seq=5480 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997708 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33721 bytes_read=101512 bytes_retransmit=9 bytes_invalid=0 send_seq=5467 receive_seq=5467 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87813 bytes_read=2115441 bytes_retransmit=0 bytes_invalid=0 send_seq=10026 receive_seq=10026 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998681 coil_temp=17.0 refs=0 mcu_temp=20.34 supply_voltage=3.011 th0: temp=53.7 th1: temp=54.8 th2: temp=59.4 th3: temp=57.1 sysload=0.20 cputime=384.744 memavail=7396192 print_time=5329.138 buffer_time=2.189 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 26 Hz
Stats 5305.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24406560 bytes_read=3764264 bytes_retransmit=9 bytes_invalid=0 send_seq=457819 receive_seq=457819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015748 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32974 bytes_read=103557 bytes_retransmit=0 bytes_invalid=0 send_seq=5467 receive_seq=5467 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997312 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168590 bytes_read=5281721 bytes_retransmit=9 bytes_invalid=0 send_seq=23231 receive_seq=23231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997713 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94527 bytes_read=2147418 bytes_retransmit=9 bytes_invalid=0 send_seq=12749 receive_seq=12749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997541 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33241 bytes_read=1353544 bytes_retransmit=9 bytes_invalid=0 send_seq=5481 receive_seq=5481 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997715 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33727 bytes_read=101528 bytes_retransmit=9 bytes_invalid=0 send_seq=5468 receive_seq=5468 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87819 bytes_read=2115797 bytes_retransmit=0 bytes_invalid=0 send_seq=10027 receive_seq=10027 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998716 coil_temp=17.0 refs=0 mcu_temp=20.34 supply_voltage=3.011 th0: temp=53.8 th1: temp=54.7 th2: temp=59.6 th3: temp=57.4 sysload=0.18 cputime=384.826 memavail=7389388 print_time=5330.112 buffer_time=2.162 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 27 Hz
Stats 5306.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24408349 bytes_read=3764834 bytes_retransmit=9 bytes_invalid=0 send_seq=457865 receive_seq=457865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015759 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32980 bytes_read=103573 bytes_retransmit=0 bytes_invalid=0 send_seq=5468 receive_seq=5468 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997317 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168596 bytes_read=5281849 bytes_retransmit=9 bytes_invalid=0 send_seq=23232 receive_seq=23232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997715 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94603 bytes_read=2150504 bytes_retransmit=9 bytes_invalid=0 send_seq=12760 receive_seq=12760 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997549 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33247 bytes_read=1353838 bytes_retransmit=9 bytes_invalid=0 send_seq=5482 receive_seq=5482 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997726 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33733 bytes_read=101544 bytes_retransmit=9 bytes_invalid=0 send_seq=5469 receive_seq=5469 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87825 bytes_read=2116153 bytes_retransmit=0 bytes_invalid=0 send_seq=10028 receive_seq=10028 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998751 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=53.9 th1: temp=55.0 th2: temp=59.5 th3: temp=57.2 sysload=0.18 cputime=384.906 memavail=7395536 print_time=5330.960 buffer_time=2.011 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 28 Hz
Stats 5307.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24410687 bytes_read=3765419 bytes_retransmit=9 bytes_invalid=0 send_seq=457920 receive_seq=457920 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=0 freq=400015782 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32986 bytes_read=103589 bytes_retransmit=0 bytes_invalid=0 send_seq=5469 receive_seq=5469 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997327 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168602 bytes_read=5281949 bytes_retransmit=9 bytes_invalid=0 send_seq=23233 receive_seq=23233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997661 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94679 bytes_read=2153560 bytes_retransmit=9 bytes_invalid=0 send_seq=12771 receive_seq=12771 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997559 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33253 bytes_read=1354072 bytes_retransmit=9 bytes_invalid=0 send_seq=5483 receive_seq=5483 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997730 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33739 bytes_read=101571 bytes_retransmit=9 bytes_invalid=0 send_seq=5470 receive_seq=5470 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87831 bytes_read=2116509 bytes_retransmit=0 bytes_invalid=0 send_seq=10029 receive_seq=10029 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998732 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=54.0 th1: temp=54.9 th2: temp=59.8 th3: temp=57.2 sysload=0.18 cputime=384.989 memavail=7394064 print_time=5332.213 buffer_time=2.263 print_stall=0 extruder: target=0 temp=19.5 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 29 Hz
Stats 5308.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24412633 bytes_read=3765978 bytes_retransmit=9 bytes_invalid=0 send_seq=457967 receive_seq=457967 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015769 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32992 bytes_read=103605 bytes_retransmit=0 bytes_invalid=0 send_seq=5470 receive_seq=5470 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997299 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168608 bytes_read=5282063 bytes_retransmit=9 bytes_invalid=0 send_seq=23234 receive_seq=23234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997617 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94755 bytes_read=2156616 bytes_retransmit=9 bytes_invalid=0 send_seq=12782 receive_seq=12782 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997488 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33259 bytes_read=1354321 bytes_retransmit=9 bytes_invalid=0 send_seq=5484 receive_seq=5484 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997755 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33745 bytes_read=101587 bytes_retransmit=9 bytes_invalid=0 send_seq=5471 receive_seq=5471 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999466 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87837 bytes_read=2116865 bytes_retransmit=0 bytes_invalid=0 send_seq=10030 receive_seq=10030 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998686 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=53.7 th1: temp=55.2 th2: temp=59.7 th3: temp=57.3 sysload=0.18 cputime=385.067 memavail=7394068 print_time=5333.136 buffer_time=2.186 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 30 Hz
Stats 5309.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24414474 bytes_read=3766538 bytes_retransmit=9 bytes_invalid=0 send_seq=458014 receive_seq=458014 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015761 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=32998 bytes_read=103634 bytes_retransmit=0 bytes_invalid=0 send_seq=5471 receive_seq=5471 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997308 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168614 bytes_read=5282191 bytes_retransmit=9 bytes_invalid=0 send_seq=23235 receive_seq=23235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997632 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94831 bytes_read=2159720 bytes_retransmit=9 bytes_invalid=0 send_seq=12793 receive_seq=12793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997517 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33265 bytes_read=1354615 bytes_retransmit=9 bytes_invalid=0 send_seq=5485 receive_seq=5485 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997751 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33751 bytes_read=101603 bytes_retransmit=9 bytes_invalid=0 send_seq=5472 receive_seq=5472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999467 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87843 bytes_read=2117221 bytes_retransmit=0 bytes_invalid=0 send_seq=10031 receive_seq=10031 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998697 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.012 th0: temp=53.8 th1: temp=55.3 th2: temp=59.7 th3: temp=57.4 sysload=0.18 cputime=385.147 memavail=7394068 print_time=5334.024 buffer_time=2.073 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 31 Hz
Stats 5310.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24416554 bytes_read=3767098 bytes_retransmit=9 bytes_invalid=0 send_seq=458064 receive_seq=458064 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015749 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33004 bytes_read=103650 bytes_retransmit=0 bytes_invalid=0 send_seq=5472 receive_seq=5472 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997310 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168620 bytes_read=5282291 bytes_retransmit=9 bytes_invalid=0 send_seq=23236 receive_seq=23236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997632 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94907 bytes_read=2162777 bytes_retransmit=9 bytes_invalid=0 send_seq=12804 receive_seq=12804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997553 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33271 bytes_read=1354849 bytes_retransmit=9 bytes_invalid=0 send_seq=5486 receive_seq=5486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997756 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33757 bytes_read=101619 bytes_retransmit=9 bytes_invalid=0 send_seq=5473 receive_seq=5473 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999462 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87849 bytes_read=2117577 bytes_retransmit=0 bytes_invalid=0 send_seq=10032 receive_seq=10032 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998689 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=53.9 th1: temp=55.1 th2: temp=59.6 th3: temp=57.3 sysload=0.17 cputime=385.227 memavail=7394068 print_time=5334.965 buffer_time=2.015 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 32 Hz
Stats 5311.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24419020 bytes_read=3767717 bytes_retransmit=9 bytes_invalid=0 send_seq=458120 receive_seq=458120 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015746 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33010 bytes_read=103666 bytes_retransmit=0 bytes_invalid=0 send_seq=5473 receive_seq=5473 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997324 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168626 bytes_read=5282391 bytes_retransmit=9 bytes_invalid=0 send_seq=23237 receive_seq=23237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997655 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=94983 bytes_read=2165835 bytes_retransmit=9 bytes_invalid=0 send_seq=12815 receive_seq=12815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997582 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33277 bytes_read=1355083 bytes_retransmit=9 bytes_invalid=0 send_seq=5487 receive_seq=5487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997764 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33763 bytes_read=101635 bytes_retransmit=9 bytes_invalid=0 send_seq=5474 receive_seq=5474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999467 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87855 bytes_read=2117933 bytes_retransmit=0 bytes_invalid=0 send_seq=10033 receive_seq=10033 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998688 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=53.9 th1: temp=55.2 th2: temp=59.8 th3: temp=57.4 sysload=0.17 cputime=385.311 memavail=7394068 print_time=5336.156 buffer_time=2.205 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 33 Hz
Stats 5312.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24420858 bytes_read=3768267 bytes_retransmit=9 bytes_invalid=0 send_seq=458165 receive_seq=458165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015744 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33016 bytes_read=103682 bytes_retransmit=0 bytes_invalid=0 send_seq=5474 receive_seq=5474 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997311 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168632 bytes_read=5282519 bytes_retransmit=9 bytes_invalid=0 send_seq=23238 receive_seq=23238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997729 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95059 bytes_read=2168978 bytes_retransmit=9 bytes_invalid=0 send_seq=12826 receive_seq=12826 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997591 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33283 bytes_read=1355377 bytes_retransmit=9 bytes_invalid=0 send_seq=5488 receive_seq=5488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997747 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33769 bytes_read=101662 bytes_retransmit=9 bytes_invalid=0 send_seq=5475 receive_seq=5475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87861 bytes_read=2118289 bytes_retransmit=0 bytes_invalid=0 send_seq=10034 receive_seq=10034 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998688 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.012 th0: temp=53.8 th1: temp=55.1 th2: temp=59.7 th3: temp=57.6 sysload=0.17 cputime=385.391 memavail=7394096 print_time=5337.060 buffer_time=2.109 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 34 Hz
Stats 5313.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24423118 bytes_read=3768847 bytes_retransmit=9 bytes_invalid=0 send_seq=458219 receive_seq=458219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015741 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33022 bytes_read=103698 bytes_retransmit=0 bytes_invalid=0 send_seq=5475 receive_seq=5475 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997308 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168638 bytes_read=5282633 bytes_retransmit=9 bytes_invalid=0 send_seq=23239 receive_seq=23239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997804 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95135 bytes_read=2172035 bytes_retransmit=9 bytes_invalid=0 send_seq=12837 receive_seq=12837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997567 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33289 bytes_read=1355626 bytes_retransmit=9 bytes_invalid=0 send_seq=5489 receive_seq=5489 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999567 adj=47997736 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33775 bytes_read=101678 bytes_retransmit=9 bytes_invalid=0 send_seq=5476 receive_seq=5476 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87867 bytes_read=2118645 bytes_retransmit=0 bytes_invalid=0 send_seq=10035 receive_seq=10035 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998682 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.012 th0: temp=53.5 th1: temp=55.0 th2: temp=59.9 th3: temp=57.5 sysload=0.17 cputime=385.471 memavail=7394096 print_time=5337.999 buffer_time=2.048 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 35 Hz
Stats 5314.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24425795 bytes_read=3769475 bytes_retransmit=9 bytes_invalid=0 send_seq=458279 receive_seq=458279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015718 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33034 bytes_read=103743 bytes_retransmit=0 bytes_invalid=0 send_seq=5477 receive_seq=5477 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997303 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168650 bytes_read=5282749 bytes_retransmit=9 bytes_invalid=0 send_seq=23241 receive_seq=23241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997765 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95217 bytes_read=2175125 bytes_retransmit=9 bytes_invalid=0 send_seq=12849 receive_seq=12849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997557 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33301 bytes_read=1355876 bytes_retransmit=9 bytes_invalid=0 send_seq=5491 receive_seq=5491 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999565 adj=47997795 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33787 bytes_read=101710 bytes_retransmit=9 bytes_invalid=0 send_seq=5478 receive_seq=5478 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87879 bytes_read=2119017 bytes_retransmit=0 bytes_invalid=0 send_seq=10037 receive_seq=10037 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998687 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.6 th1: temp=55.2 th2: temp=59.9 th3: temp=57.5 sysload=0.17 cputime=385.558 memavail=7394096 print_time=5339.214 buffer_time=2.262 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 36 Hz
Stats 5315.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24427606 bytes_read=3770030 bytes_retransmit=9 bytes_invalid=0 send_seq=458325 receive_seq=458325 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015716 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33040 bytes_read=103759 bytes_retransmit=0 bytes_invalid=0 send_seq=5478 receive_seq=5478 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997329 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168656 bytes_read=5282877 bytes_retransmit=9 bytes_invalid=0 send_seq=23242 receive_seq=23242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997748 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95293 bytes_read=2178209 bytes_retransmit=9 bytes_invalid=0 send_seq=12860 receive_seq=12860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997566 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33307 bytes_read=1356170 bytes_retransmit=9 bytes_invalid=0 send_seq=5492 receive_seq=5492 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997766 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33793 bytes_read=101726 bytes_retransmit=9 bytes_invalid=0 send_seq=5479 receive_seq=5479 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87885 bytes_read=2119373 bytes_retransmit=0 bytes_invalid=0 send_seq=10038 receive_seq=10038 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998696 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.012 th0: temp=53.9 th1: temp=55.4 th2: temp=59.9 th3: temp=57.5 sysload=0.15 cputime=385.638 memavail=7394096 print_time=5340.091 buffer_time=2.138 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 37 Hz
Stats 5316.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24430039 bytes_read=3770635 bytes_retransmit=9 bytes_invalid=0 send_seq=458381 receive_seq=458381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015708 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33046 bytes_read=103775 bytes_retransmit=0 bytes_invalid=0 send_seq=5479 receive_seq=5479 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997322 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168662 bytes_read=5282977 bytes_retransmit=9 bytes_invalid=0 send_seq=23243 receive_seq=23243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997721 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95369 bytes_read=2181269 bytes_retransmit=9 bytes_invalid=0 send_seq=12871 receive_seq=12871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997549 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33313 bytes_read=1356404 bytes_retransmit=9 bytes_invalid=0 send_seq=5493 receive_seq=5493 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997742 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33799 bytes_read=101742 bytes_retransmit=9 bytes_invalid=0 send_seq=5480 receive_seq=5480 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87891 bytes_read=2119729 bytes_retransmit=0 bytes_invalid=0 send_seq=10039 receive_seq=10039 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998741 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.6 th1: temp=55.1 th2: temp=59.8 th3: temp=57.5 sysload=0.15 cputime=385.718 memavail=7394096 print_time=5341.027 buffer_time=2.073 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 38 Hz
Stats 5317.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24432794 bytes_read=3771269 bytes_retransmit=9 bytes_invalid=0 send_seq=458443 receive_seq=458443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015708 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33052 bytes_read=103791 bytes_retransmit=0 bytes_invalid=0 send_seq=5480 receive_seq=5480 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997314 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168668 bytes_read=5283077 bytes_retransmit=9 bytes_invalid=0 send_seq=23244 receive_seq=23244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997710 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95445 bytes_read=2184325 bytes_retransmit=9 bytes_invalid=0 send_seq=12882 receive_seq=12882 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997546 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33319 bytes_read=1356638 bytes_retransmit=9 bytes_invalid=0 send_seq=5494 receive_seq=5494 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997731 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33805 bytes_read=101769 bytes_retransmit=9 bytes_invalid=0 send_seq=5481 receive_seq=5481 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87897 bytes_read=2120085 bytes_retransmit=0 bytes_invalid=0 send_seq=10040 receive_seq=10040 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998730 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=54.0 th1: temp=55.5 th2: temp=60.1 th3: temp=57.6 sysload=0.15 cputime=385.804 memavail=7394104 print_time=5342.225 buffer_time=2.271 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 39 Hz
Stats 5318.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24434673 bytes_read=3771829 bytes_retransmit=9 bytes_invalid=0 send_seq=458490 receive_seq=458490 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015713 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33058 bytes_read=103807 bytes_retransmit=0 bytes_invalid=0 send_seq=5481 receive_seq=5481 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997306 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168674 bytes_read=5283219 bytes_retransmit=9 bytes_invalid=0 send_seq=23245 receive_seq=23245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997696 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95514 bytes_read=2187387 bytes_retransmit=9 bytes_invalid=0 send_seq=12892 receive_seq=12892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33325 bytes_read=1356947 bytes_retransmit=9 bytes_invalid=0 send_seq=5495 receive_seq=5495 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997702 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33811 bytes_read=101785 bytes_retransmit=9 bytes_invalid=0 send_seq=5482 receive_seq=5482 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87903 bytes_read=2120441 bytes_retransmit=0 bytes_invalid=0 send_seq=10041 receive_seq=10041 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998705 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.012 th0: temp=54.1 th1: temp=55.3 th2: temp=60.1 th3: temp=57.6 sysload=0.15 cputime=385.885 memavail=7393896 print_time=5343.104 buffer_time=2.150 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 40 Hz
Stats 5319.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24437171 bytes_read=3772429 bytes_retransmit=9 bytes_invalid=0 send_seq=458548 receive_seq=458548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015714 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33064 bytes_read=103823 bytes_retransmit=0 bytes_invalid=0 send_seq=5482 receive_seq=5482 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997302 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168680 bytes_read=5283319 bytes_retransmit=9 bytes_invalid=0 send_seq=23246 receive_seq=23246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997666 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95590 bytes_read=2190519 bytes_retransmit=9 bytes_invalid=0 send_seq=12903 receive_seq=12903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33331 bytes_read=1357181 bytes_retransmit=9 bytes_invalid=0 send_seq=5496 receive_seq=5496 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33817 bytes_read=101801 bytes_retransmit=9 bytes_invalid=0 send_seq=5483 receive_seq=5483 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87909 bytes_read=2120797 bytes_retransmit=0 bytes_invalid=0 send_seq=10042 receive_seq=10042 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998703 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.012 th0: temp=53.9 th1: temp=55.5 th2: temp=60.0 th3: temp=57.6 sysload=0.15 cputime=385.966 memavail=7393896 print_time=5344.026 buffer_time=2.071 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 41 Hz
Stats 5320.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24440115 bytes_read=3773078 bytes_retransmit=9 bytes_invalid=0 send_seq=458613 receive_seq=458613 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=23 upcoming_bytes=0 freq=400015711 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33070 bytes_read=103852 bytes_retransmit=0 bytes_invalid=0 send_seq=5483 receive_seq=5483 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997310 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168686 bytes_read=5283419 bytes_retransmit=9 bytes_invalid=0 send_seq=23247 receive_seq=23247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997654 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95666 bytes_read=2193578 bytes_retransmit=9 bytes_invalid=0 send_seq=12914 receive_seq=12914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997513 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33337 bytes_read=1357415 bytes_retransmit=9 bytes_invalid=0 send_seq=5497 receive_seq=5497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33823 bytes_read=101817 bytes_retransmit=9 bytes_invalid=0 send_seq=5484 receive_seq=5484 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87915 bytes_read=2121153 bytes_retransmit=0 bytes_invalid=0 send_seq=10043 receive_seq=10043 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998708 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.012 th0: temp=54.0 th1: temp=55.3 th2: temp=60.1 th3: temp=57.7 sysload=0.14 cputime=386.053 memavail=7393900 print_time=5345.252 buffer_time=2.296 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 42 Hz
Stats 5321.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24442155 bytes_read=3773668 bytes_retransmit=9 bytes_invalid=0 send_seq=458663 receive_seq=458663 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015713 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33076 bytes_read=103868 bytes_retransmit=0 bytes_invalid=0 send_seq=5484 receive_seq=5484 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997303 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168692 bytes_read=5283547 bytes_retransmit=9 bytes_invalid=0 send_seq=23248 receive_seq=23248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997654 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95742 bytes_read=2196666 bytes_retransmit=9 bytes_invalid=0 send_seq=12925 receive_seq=12925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997521 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33343 bytes_read=1357709 bytes_retransmit=9 bytes_invalid=0 send_seq=5498 receive_seq=5498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33829 bytes_read=101833 bytes_retransmit=9 bytes_invalid=0 send_seq=5485 receive_seq=5485 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999448 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87921 bytes_read=2121509 bytes_retransmit=0 bytes_invalid=0 send_seq=10044 receive_seq=10044 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998699 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.9 th1: temp=55.4 th2: temp=59.9 th3: temp=57.8 sysload=0.14 cputime=386.138 memavail=7390620 print_time=5346.134 buffer_time=2.177 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 43 Hz
Stats 5322.3: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24444751 bytes_read=3774268 bytes_retransmit=9 bytes_invalid=0 send_seq=458721 receive_seq=458721 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015707 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33082 bytes_read=103884 bytes_retransmit=0 bytes_invalid=0 send_seq=5485 receive_seq=5485 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997305 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168698 bytes_read=5283647 bytes_retransmit=9 bytes_invalid=0 send_seq=23249 receive_seq=23249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997684 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95818 bytes_read=2199722 bytes_retransmit=9 bytes_invalid=0 send_seq=12936 receive_seq=12936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33349 bytes_read=1357943 bytes_retransmit=9 bytes_invalid=0 send_seq=5499 receive_seq=5499 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33835 bytes_read=101860 bytes_retransmit=9 bytes_invalid=0 send_seq=5486 receive_seq=5486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87927 bytes_read=2121865 bytes_retransmit=0 bytes_invalid=0 send_seq=10045 receive_seq=10045 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998686 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=54.0 th1: temp=55.5 th2: temp=60.0 th3: temp=57.7 sysload=0.14 cputime=386.226 memavail=7395168 print_time=5347.060 buffer_time=2.103 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 44 Hz
Stats 5323.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24447691 bytes_read=3774867 bytes_retransmit=9 bytes_invalid=0 send_seq=458783 receive_seq=458773 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=0 freq=400015706 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33088 bytes_read=103900 bytes_retransmit=0 bytes_invalid=0 send_seq=5486 receive_seq=5486 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997303 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168704 bytes_read=5283775 bytes_retransmit=9 bytes_invalid=0 send_seq=23250 receive_seq=23250 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997676 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95894 bytes_read=2202782 bytes_retransmit=9 bytes_invalid=0 send_seq=12947 receive_seq=12947 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33355 bytes_read=1358192 bytes_retransmit=9 bytes_invalid=0 send_seq=5500 receive_seq=5500 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33841 bytes_read=101876 bytes_retransmit=9 bytes_invalid=0 send_seq=5487 receive_seq=5487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87933 bytes_read=2122221 bytes_retransmit=0 bytes_invalid=0 send_seq=10046 receive_seq=10046 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998677 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.9 th1: temp=55.5 th2: temp=60.2 th3: temp=57.8 sysload=0.14 cputime=386.323 memavail=7395036 print_time=5348.264 buffer_time=2.301 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 45 Hz
Stats 5324.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24449813 bytes_read=3775480 bytes_retransmit=9 bytes_invalid=0 send_seq=458834 receive_seq=458834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015706 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33094 bytes_read=103916 bytes_retransmit=0 bytes_invalid=0 send_seq=5487 receive_seq=5487 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997294 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168710 bytes_read=5283889 bytes_retransmit=9 bytes_invalid=0 send_seq=23251 receive_seq=23251 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997666 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=95970 bytes_read=2205883 bytes_retransmit=9 bytes_invalid=0 send_seq=12958 receive_seq=12958 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33361 bytes_read=1358486 bytes_retransmit=9 bytes_invalid=0 send_seq=5501 receive_seq=5501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33847 bytes_read=101892 bytes_retransmit=9 bytes_invalid=0 send_seq=5488 receive_seq=5488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87939 bytes_read=2122577 bytes_retransmit=0 bytes_invalid=0 send_seq=10047 receive_seq=10047 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998671 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.012 th0: temp=53.7 th1: temp=55.4 th2: temp=60.1 th3: temp=57.7 sysload=0.14 cputime=386.406 memavail=7395036 print_time=5349.159 buffer_time=2.195 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 46 Hz
Stats 5325.4: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24452394 bytes_read=3776083 bytes_retransmit=9 bytes_invalid=0 send_seq=458893 receive_seq=458893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015698 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=33100 bytes_read=103945 bytes_retransmit=0 bytes_invalid=0 send_seq=5488 receive_seq=5488 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997293 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168716 bytes_read=5283989 bytes_retransmit=9 bytes_invalid=0 send_seq=23252 receive_seq=23252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997655 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96046 bytes_read=2208997 bytes_retransmit=9 bytes_invalid=0 send_seq=12969 receive_seq=12969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997497 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33367 bytes_read=1358720 bytes_retransmit=9 bytes_invalid=0 send_seq=5502 receive_seq=5502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33853 bytes_read=101908 bytes_retransmit=9 bytes_invalid=0 send_seq=5489 receive_seq=5489 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87945 bytes_read=2122933 bytes_retransmit=0 bytes_invalid=0 send_seq=10048 receive_seq=10048 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998671 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=54.1 th1: temp=55.7 th2: temp=60.3 th3: temp=57.8 sysload=0.13 cputime=386.489 memavail=7395036 print_time=5350.074 buffer_time=2.109 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 47 Hz
Stats 5326.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24454507 bytes_read=3776697 bytes_retransmit=9 bytes_invalid=0 send_seq=458945 receive_seq=458945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015699 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=33106 bytes_read=103961 bytes_retransmit=0 bytes_invalid=0 send_seq=5489 receive_seq=5489 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997302 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168722 bytes_read=5284103 bytes_retransmit=9 bytes_invalid=0 send_seq=23253 receive_seq=23253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997660 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96122 bytes_read=2212053 bytes_retransmit=9 bytes_invalid=0 send_seq=12980 receive_seq=12980 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33373 bytes_read=1358954 bytes_retransmit=9 bytes_invalid=0 send_seq=5503 receive_seq=5503 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997738 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33859 bytes_read=101924 bytes_retransmit=9 bytes_invalid=0 send_seq=5490 receive_seq=5490 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87951 bytes_read=2123280 bytes_retransmit=0 bytes_invalid=0 send_seq=10049 receive_seq=10049 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998689 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.012 th0: temp=54.0 th1: temp=55.6 th2: temp=60.1 th3: temp=57.7 sysload=0.13 cputime=386.572 memavail=7395036 print_time=5350.971 buffer_time=2.006 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 48 Hz
Stats 5327.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24457664 bytes_read=3777347 bytes_retransmit=9 bytes_invalid=0 send_seq=459013 receive_seq=459013 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015695 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=33112 bytes_read=103977 bytes_retransmit=0 bytes_invalid=0 send_seq=5490 receive_seq=5490 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997339 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168728 bytes_read=5284217 bytes_retransmit=9 bytes_invalid=0 send_seq=23254 receive_seq=23254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997830 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96198 bytes_read=2215138 bytes_retransmit=9 bytes_invalid=0 send_seq=12991 receive_seq=12991 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997521 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33379 bytes_read=1359248 bytes_retransmit=9 bytes_invalid=0 send_seq=5504 receive_seq=5504 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997731 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33865 bytes_read=101951 bytes_retransmit=9 bytes_invalid=0 send_seq=5491 receive_seq=5491 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87957 bytes_read=2123625 bytes_retransmit=0 bytes_invalid=0 send_seq=10050 receive_seq=10050 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998675 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=54.0 th1: temp=55.6 th2: temp=60.2 th3: temp=57.8 sysload=0.13 cputime=386.662 memavail=7394320 print_time=5352.176 buffer_time=2.211 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 49 Hz
Stats 5328.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24460358 bytes_read=3777957 bytes_retransmit=9 bytes_invalid=0 send_seq=459073 receive_seq=459073 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015688 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=33118 bytes_read=103993 bytes_retransmit=0 bytes_invalid=0 send_seq=5491 receive_seq=5491 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997329 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168734 bytes_read=5284331 bytes_retransmit=9 bytes_invalid=0 send_seq=23255 receive_seq=23255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997791 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96274 bytes_read=2218195 bytes_retransmit=9 bytes_invalid=0 send_seq=13002 receive_seq=13002 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997697 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33385 bytes_read=1359497 bytes_retransmit=9 bytes_invalid=0 send_seq=5505 receive_seq=5505 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997706 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33871 bytes_read=101967 bytes_retransmit=9 bytes_invalid=0 send_seq=5492 receive_seq=5492 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87963 bytes_read=2123970 bytes_retransmit=0 bytes_invalid=0 send_seq=10051 receive_seq=10051 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998675 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=53.9 th1: temp=55.5 th2: temp=60.2 th3: temp=57.8 sysload=0.13 cputime=386.745 memavail=7394324 print_time=5353.090 buffer_time=2.125 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 50 Hz
Stats 5329.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24462532 bytes_read=3778561 bytes_retransmit=9 bytes_invalid=0 send_seq=459126 receive_seq=459126 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015845 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=33124 bytes_read=104009 bytes_retransmit=0 bytes_invalid=0 send_seq=5492 receive_seq=5492 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997326 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168740 bytes_read=5284445 bytes_retransmit=9 bytes_invalid=0 send_seq=23256 receive_seq=23256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997772 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96350 bytes_read=2221271 bytes_retransmit=9 bytes_invalid=0 send_seq=13013 receive_seq=13013 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997672 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33391 bytes_read=1359731 bytes_retransmit=9 bytes_invalid=0 send_seq=5506 receive_seq=5506 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997705 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33877 bytes_read=101983 bytes_retransmit=9 bytes_invalid=0 send_seq=5493 receive_seq=5493 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87969 bytes_read=2124315 bytes_retransmit=0 bytes_invalid=0 send_seq=10052 receive_seq=10052 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998681 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=54.3 th1: temp=55.7 th2: temp=60.3 th3: temp=57.8 sysload=0.13 cputime=386.826 memavail=7394324 print_time=5353.988 buffer_time=2.022 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 51 Hz
Stats 5330.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24465671 bytes_read=3779196 bytes_retransmit=9 bytes_invalid=0 send_seq=459191 receive_seq=459191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015837 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33130 bytes_read=104038 bytes_retransmit=0 bytes_invalid=0 send_seq=5493 receive_seq=5493 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997060 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168746 bytes_read=5284559 bytes_retransmit=9 bytes_invalid=0 send_seq=23257 receive_seq=23257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997423 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96426 bytes_read=2224359 bytes_retransmit=9 bytes_invalid=0 send_seq=13024 receive_seq=13024 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997323 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33397 bytes_read=1360025 bytes_retransmit=9 bytes_invalid=0 send_seq=5507 receive_seq=5507 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997477 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33883 bytes_read=101999 bytes_retransmit=9 bytes_invalid=0 send_seq=5494 receive_seq=5494 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999384 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87975 bytes_read=2124660 bytes_retransmit=0 bytes_invalid=0 send_seq=10053 receive_seq=10053 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998540 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=53.9 th1: temp=55.6 th2: temp=60.2 th3: temp=57.8 sysload=0.12 cputime=386.915 memavail=7394324 print_time=5355.191 buffer_time=2.223 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 52 Hz
Stats 5331.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24468497 bytes_read=3779831 bytes_retransmit=9 bytes_invalid=0 send_seq=459253 receive_seq=459253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015829 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33136 bytes_read=104054 bytes_retransmit=0 bytes_invalid=0 send_seq=5494 receive_seq=5494 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997120 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168752 bytes_read=5284659 bytes_retransmit=9 bytes_invalid=0 send_seq=23258 receive_seq=23258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997581 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96502 bytes_read=2227415 bytes_retransmit=9 bytes_invalid=0 send_seq=13035 receive_seq=13035 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997386 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33403 bytes_read=1360259 bytes_retransmit=9 bytes_invalid=0 send_seq=5508 receive_seq=5508 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997550 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33889 bytes_read=102015 bytes_retransmit=9 bytes_invalid=0 send_seq=5495 receive_seq=5495 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999403 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87981 bytes_read=2125005 bytes_retransmit=0 bytes_invalid=0 send_seq=10054 receive_seq=10054 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998589 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=54.0 th1: temp=55.6 th2: temp=60.3 th3: temp=57.8 sysload=0.12 cputime=386.998 memavail=7394324 print_time=5356.105 buffer_time=2.137 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 53 Hz
Stats 5332.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24470725 bytes_read=3780435 bytes_retransmit=9 bytes_invalid=0 send_seq=459306 receive_seq=459306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015829 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33142 bytes_read=104070 bytes_retransmit=0 bytes_invalid=0 send_seq=5495 receive_seq=5495 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997155 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168758 bytes_read=5284773 bytes_retransmit=9 bytes_invalid=0 send_seq=23259 receive_seq=23259 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997583 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96578 bytes_read=2230530 bytes_retransmit=9 bytes_invalid=0 send_seq=13046 receive_seq=13046 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997404 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33409 bytes_read=1360493 bytes_retransmit=9 bytes_invalid=0 send_seq=5509 receive_seq=5509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997563 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33895 bytes_read=102042 bytes_retransmit=9 bytes_invalid=0 send_seq=5496 receive_seq=5496 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999409 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87987 bytes_read=2125350 bytes_retransmit=0 bytes_invalid=0 send_seq=10055 receive_seq=10055 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998596 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=54.1 th1: temp=55.6 th2: temp=60.2 th3: temp=57.8 sysload=0.12 cputime=387.081 memavail=7394336 print_time=5356.999 buffer_time=2.030 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 54 Hz
Stats 5333.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24473981 bytes_read=3781095 bytes_retransmit=9 bytes_invalid=0 send_seq=459376 receive_seq=459376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015819 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33148 bytes_read=104086 bytes_retransmit=0 bytes_invalid=0 send_seq=5496 receive_seq=5496 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997169 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168764 bytes_read=5284901 bytes_retransmit=9 bytes_invalid=0 send_seq=23260 receive_seq=23260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997569 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96654 bytes_read=2233614 bytes_retransmit=9 bytes_invalid=0 send_seq=13057 receive_seq=13057 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997407 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33415 bytes_read=1360802 bytes_retransmit=9 bytes_invalid=0 send_seq=5510 receive_seq=5510 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997570 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33901 bytes_read=102058 bytes_retransmit=9 bytes_invalid=0 send_seq=5497 receive_seq=5497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999411 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87993 bytes_read=2125695 bytes_retransmit=0 bytes_invalid=0 send_seq=10056 receive_seq=10056 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998616 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=53.9 th1: temp=55.6 th2: temp=60.2 th3: temp=57.9 sysload=0.12 cputime=387.172 memavail=7394336 print_time=5358.208 buffer_time=2.238 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 55 Hz
Stats 5334.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24476883 bytes_read=3781720 bytes_retransmit=9 bytes_invalid=0 send_seq=459439 receive_seq=459439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015807 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33154 bytes_read=104101 bytes_retransmit=0 bytes_invalid=0 send_seq=5497 receive_seq=5497 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997212 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168770 bytes_read=5285001 bytes_retransmit=9 bytes_invalid=0 send_seq=23261 receive_seq=23261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997600 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96730 bytes_read=2236687 bytes_retransmit=9 bytes_invalid=0 send_seq=13068 receive_seq=13068 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997448 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33421 bytes_read=1361036 bytes_retransmit=9 bytes_invalid=0 send_seq=5511 receive_seq=5511 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997599 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33907 bytes_read=102074 bytes_retransmit=9 bytes_invalid=0 send_seq=5498 receive_seq=5498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999422 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=87999 bytes_read=2126045 bytes_retransmit=0 bytes_invalid=0 send_seq=10057 receive_seq=10057 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998648 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=54.0 th1: temp=55.7 th2: temp=60.5 th3: temp=57.9 sysload=0.12 cputime=387.257 memavail=7394336 print_time=5359.118 buffer_time=2.147 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 56 Hz
Stats 5335.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24479179 bytes_read=3782330 bytes_retransmit=9 bytes_invalid=0 send_seq=459494 receive_seq=459494 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015807 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33160 bytes_read=104129 bytes_retransmit=0 bytes_invalid=0 send_seq=5498 receive_seq=5498 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997233 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168776 bytes_read=5285115 bytes_retransmit=9 bytes_invalid=0 send_seq=23262 receive_seq=23262 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997625 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96799 bytes_read=2239735 bytes_retransmit=9 bytes_invalid=0 send_seq=13078 receive_seq=13078 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997468 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33427 bytes_read=1361270 bytes_retransmit=9 bytes_invalid=0 send_seq=5512 receive_seq=5512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997610 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33913 bytes_read=102090 bytes_retransmit=9 bytes_invalid=0 send_seq=5499 receive_seq=5499 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88005 bytes_read=2126401 bytes_retransmit=0 bytes_invalid=0 send_seq=10058 receive_seq=10058 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998654 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=53.8 th1: temp=55.7 th2: temp=60.5 th3: temp=57.9 sysload=0.11 cputime=387.340 memavail=7394336 print_time=5360.026 buffer_time=2.053 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 57 Hz
Stats 5336.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24482538 bytes_read=3783016 bytes_retransmit=9 bytes_invalid=0 send_seq=459566 receive_seq=459566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=400015804 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33166 bytes_read=104144 bytes_retransmit=0 bytes_invalid=0 send_seq=5499 receive_seq=5499 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997228 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168782 bytes_read=5285229 bytes_retransmit=9 bytes_invalid=0 send_seq=23263 receive_seq=23263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997612 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96875 bytes_read=2242808 bytes_retransmit=9 bytes_invalid=0 send_seq=13089 receive_seq=13089 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997458 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33433 bytes_read=1361564 bytes_retransmit=9 bytes_invalid=0 send_seq=5513 receive_seq=5513 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997617 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33919 bytes_read=102106 bytes_retransmit=9 bytes_invalid=0 send_seq=5500 receive_seq=5500 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88011 bytes_read=2126757 bytes_retransmit=0 bytes_invalid=0 send_seq=10059 receive_seq=10059 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998649 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=54.1 th1: temp=55.6 th2: temp=60.4 th3: temp=57.9 sysload=0.11 cputime=387.433 memavail=7394336 print_time=5361.231 buffer_time=2.258 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 58 Hz
Stats 5337.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24485467 bytes_read=3783646 bytes_retransmit=9 bytes_invalid=0 send_seq=459630 receive_seq=459630 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015811 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33172 bytes_read=104159 bytes_retransmit=0 bytes_invalid=0 send_seq=5500 receive_seq=5500 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997233 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168788 bytes_read=5285329 bytes_retransmit=9 bytes_invalid=0 send_seq=23264 receive_seq=23264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997617 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=96951 bytes_read=2245865 bytes_retransmit=9 bytes_invalid=0 send_seq=13100 receive_seq=13100 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997469 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33439 bytes_read=1361798 bytes_retransmit=9 bytes_invalid=0 send_seq=5514 receive_seq=5514 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33925 bytes_read=102133 bytes_retransmit=9 bytes_invalid=0 send_seq=5501 receive_seq=5501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88017 bytes_read=2127131 bytes_retransmit=0 bytes_invalid=0 send_seq=10060 receive_seq=10060 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998664 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=54.0 th1: temp=55.8 th2: temp=60.5 th3: temp=57.9 sysload=0.11 cputime=387.518 memavail=7393580 print_time=5362.126 buffer_time=2.152 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 59 Hz
Stats 5338.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24487864 bytes_read=3784260 bytes_retransmit=9 bytes_invalid=0 send_seq=459685 receive_seq=459685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015822 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33178 bytes_read=104174 bytes_retransmit=0 bytes_invalid=0 send_seq=5501 receive_seq=5501 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997226 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=168794 bytes_read=5285457 bytes_retransmit=9 bytes_invalid=0 send_seq=23265 receive_seq=23265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997594 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97027 bytes_read=2248993 bytes_retransmit=9 bytes_invalid=0 send_seq=13111 receive_seq=13111 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997460 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33445 bytes_read=1362047 bytes_retransmit=9 bytes_invalid=0 send_seq=5515 receive_seq=5515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33931 bytes_read=102149 bytes_retransmit=9 bytes_invalid=0 send_seq=5502 receive_seq=5502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88023 bytes_read=2127487 bytes_retransmit=0 bytes_invalid=0 send_seq=10061 receive_seq=10061 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998645 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=54.1 th1: temp=55.7 th2: temp=60.4 th3: temp=58.0 sysload=0.11 cputime=387.605 memavail=7393616 print_time=5363.044 buffer_time=2.069 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 60 Hz
Stats 5339.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24491276 bytes_read=3784930 bytes_retransmit=9 bytes_invalid=0 send_seq=459757 receive_seq=459757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015813 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33184 bytes_read=104190 bytes_retransmit=0 bytes_invalid=0 send_seq=5502 receive_seq=5502 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997212 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=168800 bytes_read=5285571 bytes_retransmit=9 bytes_invalid=0 send_seq=23266 receive_seq=23266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997589 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97103 bytes_read=2252081 bytes_retransmit=9 bytes_invalid=0 send_seq=13122 receive_seq=13122 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997436 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33451 bytes_read=1362341 bytes_retransmit=9 bytes_invalid=0 send_seq=5516 receive_seq=5516 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997605 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33937 bytes_read=102165 bytes_retransmit=9 bytes_invalid=0 send_seq=5503 receive_seq=5503 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88029 bytes_read=2127843 bytes_retransmit=0 bytes_invalid=0 send_seq=10062 receive_seq=10062 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998637 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=54.3 th1: temp=55.6 th2: temp=60.2 th3: temp=57.8 sysload=0.11 cputime=387.699 memavail=7393616 print_time=5364.247 buffer_time=2.272 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 61 Hz
Stats 5340.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24494245 bytes_read=3785565 bytes_retransmit=9 bytes_invalid=0 send_seq=459822 receive_seq=459822 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015808 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33190 bytes_read=104219 bytes_retransmit=0 bytes_invalid=0 send_seq=5503 receive_seq=5503 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997263 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=168806 bytes_read=5285671 bytes_retransmit=9 bytes_invalid=0 send_seq=23267 receive_seq=23267 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997615 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97179 bytes_read=2255139 bytes_retransmit=9 bytes_invalid=0 send_seq=13133 receive_seq=13133 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33457 bytes_read=1362575 bytes_retransmit=9 bytes_invalid=0 send_seq=5517 receive_seq=5517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33943 bytes_read=102181 bytes_retransmit=9 bytes_invalid=0 send_seq=5504 receive_seq=5504 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88035 bytes_read=2128199 bytes_retransmit=0 bytes_invalid=0 send_seq=10063 receive_seq=10063 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998660 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=53.9 th1: temp=55.7 th2: temp=60.5 th3: temp=57.9 sysload=0.10 cputime=387.794 memavail=7393608 print_time=5365.133 buffer_time=2.157 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 62 Hz
Stats 5341.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24496750 bytes_read=3786210 bytes_retransmit=9 bytes_invalid=0 send_seq=459880 receive_seq=459880 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015800 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33196 bytes_read=104235 bytes_retransmit=0 bytes_invalid=0 send_seq=5504 receive_seq=5504 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997272 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=168812 bytes_read=5285785 bytes_retransmit=9 bytes_invalid=0 send_seq=23268 receive_seq=23268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997618 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97255 bytes_read=2258210 bytes_retransmit=9 bytes_invalid=0 send_seq=13144 receive_seq=13144 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997484 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33463 bytes_read=1362809 bytes_retransmit=9 bytes_invalid=0 send_seq=5518 receive_seq=5518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997629 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33949 bytes_read=102197 bytes_retransmit=9 bytes_invalid=0 send_seq=5505 receive_seq=5505 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88041 bytes_read=2128555 bytes_retransmit=0 bytes_invalid=0 send_seq=10064 receive_seq=10064 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998660 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=54.1 th1: temp=55.6 th2: temp=60.3 th3: temp=57.9 sysload=0.10 cputime=387.882 memavail=7393732 print_time=5366.061 buffer_time=2.085 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 63 Hz
Stats 5342.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24500309 bytes_read=3786895 bytes_retransmit=9 bytes_invalid=0 send_seq=459955 receive_seq=459955 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=400015802 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33202 bytes_read=104251 bytes_retransmit=0 bytes_invalid=0 send_seq=5505 receive_seq=5505 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997278 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=168818 bytes_read=5285899 bytes_retransmit=9 bytes_invalid=0 send_seq=23269 receive_seq=23269 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997631 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97331 bytes_read=2261283 bytes_retransmit=9 bytes_invalid=0 send_seq=13155 receive_seq=13155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997503 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33469 bytes_read=1363103 bytes_retransmit=9 bytes_invalid=0 send_seq=5519 receive_seq=5519 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33955 bytes_read=102224 bytes_retransmit=9 bytes_invalid=0 send_seq=5506 receive_seq=5506 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88047 bytes_read=2128911 bytes_retransmit=0 bytes_invalid=0 send_seq=10065 receive_seq=10065 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998666 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=53.9 th1: temp=55.9 th2: temp=60.3 th3: temp=57.9 sysload=0.10 cputime=387.977 memavail=7393732 print_time=5367.268 buffer_time=2.291 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 64 Hz
Stats 5343.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24503287 bytes_read=3787525 bytes_retransmit=9 bytes_invalid=0 send_seq=460019 receive_seq=460019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015794 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33208 bytes_read=104267 bytes_retransmit=0 bytes_invalid=0 send_seq=5506 receive_seq=5506 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997265 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=168824 bytes_read=5285999 bytes_retransmit=9 bytes_invalid=0 send_seq=23270 receive_seq=23270 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997626 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97407 bytes_read=2264340 bytes_retransmit=9 bytes_invalid=0 send_seq=13166 receive_seq=13166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997495 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33475 bytes_read=1363352 bytes_retransmit=9 bytes_invalid=0 send_seq=5520 receive_seq=5520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33961 bytes_read=102240 bytes_retransmit=9 bytes_invalid=0 send_seq=5507 receive_seq=5507 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88053 bytes_read=2129267 bytes_retransmit=0 bytes_invalid=0 send_seq=10066 receive_seq=10066 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998655 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=54.1 th1: temp=55.6 th2: temp=60.3 th3: temp=58.1 sysload=0.10 cputime=388.063 memavail=7393732 print_time=5368.143 buffer_time=2.166 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.5 pwm=0.000
Testing frequency 65 Hz
Stats 5344.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24505894 bytes_read=3788159 bytes_retransmit=9 bytes_invalid=0 send_seq=460078 receive_seq=460078 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015900 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33214 bytes_read=104283 bytes_retransmit=0 bytes_invalid=0 send_seq=5507 receive_seq=5507 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997272 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168830 bytes_read=5286127 bytes_retransmit=9 bytes_invalid=0 send_seq=23271 receive_seq=23271 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997633 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97483 bytes_read=2267428 bytes_retransmit=9 bytes_invalid=0 send_seq=13177 receive_seq=13177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33481 bytes_read=1363586 bytes_retransmit=9 bytes_invalid=0 send_seq=5521 receive_seq=5521 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33967 bytes_read=102256 bytes_retransmit=9 bytes_invalid=0 send_seq=5508 receive_seq=5508 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88059 bytes_read=2129623 bytes_retransmit=0 bytes_invalid=0 send_seq=10067 receive_seq=10067 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998658 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.012 th0: temp=53.9 th1: temp=55.8 th2: temp=60.3 th3: temp=57.9 sysload=0.10 cputime=388.151 memavail=7393732 print_time=5369.075 buffer_time=2.098 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 66 Hz
Stats 5345.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24509576 bytes_read=3788849 bytes_retransmit=9 bytes_invalid=0 send_seq=460154 receive_seq=460154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=400015889 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33220 bytes_read=104312 bytes_retransmit=0 bytes_invalid=0 send_seq=5508 receive_seq=5508 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997109 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168836 bytes_read=5286234 bytes_retransmit=9 bytes_invalid=0 send_seq=23272 receive_seq=23272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997420 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97559 bytes_read=2270488 bytes_retransmit=9 bytes_invalid=0 send_seq=13188 receive_seq=13188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997288 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33487 bytes_read=1363860 bytes_retransmit=9 bytes_invalid=0 send_seq=5522 receive_seq=5522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997488 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33973 bytes_read=102272 bytes_retransmit=9 bytes_invalid=0 send_seq=5509 receive_seq=5509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999397 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88065 bytes_read=2129979 bytes_retransmit=0 bytes_invalid=0 send_seq=10068 receive_seq=10068 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998544 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.012 th0: temp=54.1 th1: temp=55.9 th2: temp=60.3 th3: temp=57.9 sysload=0.09 cputime=388.247 memavail=7393732 print_time=5370.282 buffer_time=2.304 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 67 Hz
Stats 5346.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24512627 bytes_read=3789501 bytes_retransmit=9 bytes_invalid=0 send_seq=460220 receive_seq=460220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015878 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33226 bytes_read=104328 bytes_retransmit=0 bytes_invalid=0 send_seq=5509 receive_seq=5509 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997170 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168842 bytes_read=5286327 bytes_retransmit=9 bytes_invalid=0 send_seq=23273 receive_seq=23273 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997506 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97635 bytes_read=2273527 bytes_retransmit=9 bytes_invalid=0 send_seq=13199 receive_seq=13199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997365 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33493 bytes_read=1364077 bytes_retransmit=9 bytes_invalid=0 send_seq=5523 receive_seq=5523 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997543 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33979 bytes_read=102288 bytes_retransmit=9 bytes_invalid=0 send_seq=5510 receive_seq=5510 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999413 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88071 bytes_read=2130335 bytes_retransmit=0 bytes_invalid=0 send_seq=10069 receive_seq=10069 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998581 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=54.2 th1: temp=55.8 th2: temp=60.3 th3: temp=57.9 sysload=0.09 cputime=388.334 memavail=7393732 print_time=5371.163 buffer_time=2.185 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 68 Hz
Stats 5347.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24515313 bytes_read=3790135 bytes_retransmit=9 bytes_invalid=0 send_seq=460279 receive_seq=460279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015871 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33232 bytes_read=104344 bytes_retransmit=0 bytes_invalid=0 send_seq=5510 receive_seq=5510 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997207 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168848 bytes_read=5286433 bytes_retransmit=9 bytes_invalid=0 send_seq=23274 receive_seq=23274 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997536 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97711 bytes_read=2276639 bytes_retransmit=9 bytes_invalid=0 send_seq=13210 receive_seq=13210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997433 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33499 bytes_read=1364295 bytes_retransmit=9 bytes_invalid=0 send_seq=5524 receive_seq=5524 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997566 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33985 bytes_read=102315 bytes_retransmit=9 bytes_invalid=0 send_seq=5511 receive_seq=5511 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999418 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88077 bytes_read=2130691 bytes_retransmit=0 bytes_invalid=0 send_seq=10070 receive_seq=10070 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998593 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=54.0 th1: temp=55.7 th2: temp=60.3 th3: temp=57.9 sysload=0.09 cputime=388.424 memavail=7393764 print_time=5372.087 buffer_time=2.109 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 69 Hz
Stats 5348.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24518980 bytes_read=3790820 bytes_retransmit=9 bytes_invalid=0 send_seq=460354 receive_seq=460354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=0 freq=400015856 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33238 bytes_read=104360 bytes_retransmit=0 bytes_invalid=0 send_seq=5511 receive_seq=5511 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997236 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168854 bytes_read=5286539 bytes_retransmit=9 bytes_invalid=0 send_seq=23275 receive_seq=23275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997555 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97787 bytes_read=2279693 bytes_retransmit=9 bytes_invalid=0 send_seq=13221 receive_seq=13221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997545 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33505 bytes_read=1364584 bytes_retransmit=9 bytes_invalid=0 send_seq=5525 receive_seq=5525 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997588 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33991 bytes_read=102331 bytes_retransmit=9 bytes_invalid=0 send_seq=5512 receive_seq=5512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999425 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88083 bytes_read=2131047 bytes_retransmit=0 bytes_invalid=0 send_seq=10071 receive_seq=10071 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998609 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=54.2 th1: temp=55.5 th2: temp=60.3 th3: temp=58.0 sysload=0.09 cputime=388.520 memavail=7393764 print_time=5373.289 buffer_time=2.311 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 70 Hz
Stats 5349.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24522095 bytes_read=3791465 bytes_retransmit=9 bytes_invalid=0 send_seq=460421 receive_seq=460421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015839 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33244 bytes_read=104376 bytes_retransmit=0 bytes_invalid=0 send_seq=5512 receive_seq=5512 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997270 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=168860 bytes_read=5286650 bytes_retransmit=9 bytes_invalid=0 send_seq=23276 receive_seq=23276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997617 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97863 bytes_read=2282757 bytes_retransmit=9 bytes_invalid=0 send_seq=13232 receive_seq=13232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997568 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33511 bytes_read=1364802 bytes_retransmit=9 bytes_invalid=0 send_seq=5526 receive_seq=5526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=33997 bytes_read=102347 bytes_retransmit=9 bytes_invalid=0 send_seq=5513 receive_seq=5513 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88089 bytes_read=2131403 bytes_retransmit=0 bytes_invalid=0 send_seq=10072 receive_seq=10072 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998648 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=54.1 th1: temp=55.8 th2: temp=60.6 th3: temp=57.9 sysload=0.09 cputime=388.609 memavail=7393764 print_time=5374.167 buffer_time=2.189 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 71 Hz
Stats 5350.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24524981 bytes_read=3792124 bytes_retransmit=9 bytes_invalid=0 send_seq=460485 receive_seq=460485 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015832 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33250 bytes_read=104405 bytes_retransmit=0 bytes_invalid=0 send_seq=5513 receive_seq=5513 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997288 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=168866 bytes_read=5286778 bytes_retransmit=9 bytes_invalid=0 send_seq=23277 receive_seq=23277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997754 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=97939 bytes_read=2285828 bytes_retransmit=9 bytes_invalid=0 send_seq=13243 receive_seq=13243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997581 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33517 bytes_read=1365024 bytes_retransmit=9 bytes_invalid=0 send_seq=5527 receive_seq=5527 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34003 bytes_read=102363 bytes_retransmit=9 bytes_invalid=0 send_seq=5514 receive_seq=5514 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88095 bytes_read=2131759 bytes_retransmit=0 bytes_invalid=0 send_seq=10073 receive_seq=10073 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998676 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=54.1 th1: temp=55.7 th2: temp=60.4 th3: temp=57.9 sysload=0.08 cputime=388.699 memavail=7393764 print_time=5375.105 buffer_time=2.126 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 72 Hz
Stats 5351.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24528023 bytes_read=3792780 bytes_retransmit=9 bytes_invalid=0 send_seq=460551 receive_seq=460551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015824 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33256 bytes_read=104421 bytes_retransmit=0 bytes_invalid=0 send_seq=5514 receive_seq=5514 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997299 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=168872 bytes_read=5286878 bytes_retransmit=9 bytes_invalid=0 send_seq=23278 receive_seq=23278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997850 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98015 bytes_read=2288900 bytes_retransmit=9 bytes_invalid=0 send_seq=13254 receive_seq=13254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997639 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33523 bytes_read=1365318 bytes_retransmit=9 bytes_invalid=0 send_seq=5528 receive_seq=5528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34009 bytes_read=102379 bytes_retransmit=9 bytes_invalid=0 send_seq=5515 receive_seq=5515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88101 bytes_read=2132115 bytes_retransmit=0 bytes_invalid=0 send_seq=10074 receive_seq=10074 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998681 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=54.0 th1: temp=55.7 th2: temp=60.4 th3: temp=58.0 sysload=0.08 cputime=388.786 memavail=7393764 print_time=5375.982 buffer_time=2.003 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 73 Hz
Stats 5352.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24531922 bytes_read=3793490 bytes_retransmit=9 bytes_invalid=0 send_seq=460631 receive_seq=460631 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015817 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33262 bytes_read=104437 bytes_retransmit=0 bytes_invalid=0 send_seq=5515 receive_seq=5515 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997304 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=168878 bytes_read=5286978 bytes_retransmit=9 bytes_invalid=0 send_seq=23279 receive_seq=23279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997932 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98084 bytes_read=2291933 bytes_retransmit=9 bytes_invalid=0 send_seq=13264 receive_seq=13264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997641 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33529 bytes_read=1365552 bytes_retransmit=9 bytes_invalid=0 send_seq=5529 receive_seq=5529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34015 bytes_read=102406 bytes_retransmit=9 bytes_invalid=0 send_seq=5516 receive_seq=5516 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88107 bytes_read=2132471 bytes_retransmit=0 bytes_invalid=0 send_seq=10075 receive_seq=10075 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998677 coil_temp=17.0 refs=0 mcu_temp=20.27 supply_voltage=3.012 th0: temp=54.2 th1: temp=55.7 th2: temp=60.4 th3: temp=57.9 sysload=0.08 cputime=388.882 memavail=7393764 print_time=5377.185 buffer_time=2.206 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 74 Hz
Stats 5353.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24534967 bytes_read=3794159 bytes_retransmit=9 bytes_invalid=0 send_seq=460697 receive_seq=460697 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015807 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33268 bytes_read=104453 bytes_retransmit=0 bytes_invalid=0 send_seq=5516 receive_seq=5516 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997319 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=168884 bytes_read=5287106 bytes_retransmit=9 bytes_invalid=0 send_seq=23280 receive_seq=23280 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997849 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98160 bytes_read=2295003 bytes_retransmit=9 bytes_invalid=0 send_seq=13275 receive_seq=13275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997601 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33535 bytes_read=1365801 bytes_retransmit=9 bytes_invalid=0 send_seq=5530 receive_seq=5530 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34021 bytes_read=102422 bytes_retransmit=9 bytes_invalid=0 send_seq=5517 receive_seq=5517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88113 bytes_read=2132827 bytes_retransmit=0 bytes_invalid=0 send_seq=10076 receive_seq=10076 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998678 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=54.2 th1: temp=55.7 th2: temp=60.3 th3: temp=57.9 sysload=0.08 cputime=388.973 memavail=7393764 print_time=5378.118 buffer_time=2.138 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 75 Hz
Stats 5354.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24537924 bytes_read=3794789 bytes_retransmit=9 bytes_invalid=0 send_seq=460761 receive_seq=460761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015796 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33274 bytes_read=104469 bytes_retransmit=0 bytes_invalid=0 send_seq=5517 receive_seq=5517 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997324 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168890 bytes_read=5287220 bytes_retransmit=9 bytes_invalid=0 send_seq=23281 receive_seq=23281 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997896 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98236 bytes_read=2298090 bytes_retransmit=9 bytes_invalid=0 send_seq=13286 receive_seq=13286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997596 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33541 bytes_read=1366095 bytes_retransmit=9 bytes_invalid=0 send_seq=5531 receive_seq=5531 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34027 bytes_read=102438 bytes_retransmit=9 bytes_invalid=0 send_seq=5518 receive_seq=5518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88119 bytes_read=2133183 bytes_retransmit=0 bytes_invalid=0 send_seq=10077 receive_seq=10077 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998678 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=54.0 th1: temp=55.8 th2: temp=60.4 th3: temp=58.0 sysload=0.08 cputime=389.061 memavail=7393764 print_time=5378.986 buffer_time=2.007 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 76 Hz
Stats 5355.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24541882 bytes_read=3795504 bytes_retransmit=9 bytes_invalid=0 send_seq=460842 receive_seq=460842 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015807 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33280 bytes_read=104498 bytes_retransmit=0 bytes_invalid=0 send_seq=5518 receive_seq=5518 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997358 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168896 bytes_read=5287320 bytes_retransmit=9 bytes_invalid=0 send_seq=23282 receive_seq=23282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997875 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98312 bytes_read=2301205 bytes_retransmit=9 bytes_invalid=0 send_seq=13297 receive_seq=13297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997611 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33547 bytes_read=1366329 bytes_retransmit=9 bytes_invalid=0 send_seq=5532 receive_seq=5532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997677 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34033 bytes_read=102454 bytes_retransmit=9 bytes_invalid=0 send_seq=5519 receive_seq=5519 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88125 bytes_read=2133539 bytes_retransmit=0 bytes_invalid=0 send_seq=10078 receive_seq=10078 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998680 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=54.1 th1: temp=55.8 th2: temp=60.6 th3: temp=57.9 sysload=0.08 cputime=389.160 memavail=7393784 print_time=5380.188 buffer_time=2.208 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 77 Hz
Stats 5356.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24544986 bytes_read=3796194 bytes_retransmit=9 bytes_invalid=0 send_seq=460909 receive_seq=460909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015805 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33286 bytes_read=104514 bytes_retransmit=0 bytes_invalid=0 send_seq=5519 receive_seq=5519 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997326 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168902 bytes_read=5287448 bytes_retransmit=9 bytes_invalid=0 send_seq=23283 receive_seq=23283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997774 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98388 bytes_read=2304277 bytes_retransmit=9 bytes_invalid=0 send_seq=13308 receive_seq=13308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33553 bytes_read=1366563 bytes_retransmit=9 bytes_invalid=0 send_seq=5533 receive_seq=5533 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997649 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34039 bytes_read=102470 bytes_retransmit=9 bytes_invalid=0 send_seq=5520 receive_seq=5520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88131 bytes_read=2133879 bytes_retransmit=0 bytes_invalid=0 send_seq=10079 receive_seq=10079 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998658 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=54.2 th1: temp=55.7 th2: temp=60.5 th3: temp=58.1 sysload=0.08 cputime=389.252 memavail=7393784 print_time=5381.124 buffer_time=2.143 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 78 Hz
Stats 5357.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24548054 bytes_read=3796830 bytes_retransmit=9 bytes_invalid=0 send_seq=460975 receive_seq=460975 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015809 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33292 bytes_read=104530 bytes_retransmit=0 bytes_invalid=0 send_seq=5520 receive_seq=5520 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997330 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168908 bytes_read=5287548 bytes_retransmit=9 bytes_invalid=0 send_seq=23284 receive_seq=23284 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997757 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98464 bytes_read=2307351 bytes_retransmit=9 bytes_invalid=0 send_seq=13319 receive_seq=13319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33559 bytes_read=1366857 bytes_retransmit=9 bytes_invalid=0 send_seq=5534 receive_seq=5534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34045 bytes_read=102497 bytes_retransmit=9 bytes_invalid=0 send_seq=5521 receive_seq=5521 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88137 bytes_read=2134235 bytes_retransmit=0 bytes_invalid=0 send_seq=10080 receive_seq=10080 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998659 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=54.2 th1: temp=55.6 th2: temp=60.4 th3: temp=58.1 sysload=0.08 cputime=389.350 memavail=7387752 print_time=5382.000 buffer_time=2.020 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 79 Hz
Stats 5358.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24552075 bytes_read=3797545 bytes_retransmit=9 bytes_invalid=0 send_seq=461056 receive_seq=461056 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015825 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33298 bytes_read=104546 bytes_retransmit=0 bytes_invalid=0 send_seq=5521 receive_seq=5521 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997314 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168914 bytes_read=5287648 bytes_retransmit=9 bytes_invalid=0 send_seq=23285 receive_seq=23285 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997890 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98540 bytes_read=2310408 bytes_retransmit=9 bytes_invalid=0 send_seq=13330 receive_seq=13330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997545 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33565 bytes_read=1367106 bytes_retransmit=9 bytes_invalid=0 send_seq=5535 receive_seq=5535 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34051 bytes_read=102513 bytes_retransmit=9 bytes_invalid=0 send_seq=5522 receive_seq=5522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88143 bytes_read=2134591 bytes_retransmit=0 bytes_invalid=0 send_seq=10081 receive_seq=10081 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998663 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=54.1 th1: temp=55.8 th2: temp=60.4 th3: temp=58.0 sysload=0.08 cputime=389.451 memavail=7393916 print_time=5383.203 buffer_time=2.222 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 80 Hz
Stats 5359.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24555341 bytes_read=3798234 bytes_retransmit=9 bytes_invalid=0 send_seq=461126 receive_seq=461126 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015837 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33304 bytes_read=104562 bytes_retransmit=0 bytes_invalid=0 send_seq=5522 receive_seq=5522 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997282 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168920 bytes_read=5287790 bytes_retransmit=9 bytes_invalid=0 send_seq=23286 receive_seq=23286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997767 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98616 bytes_read=2313497 bytes_retransmit=9 bytes_invalid=0 send_seq=13341 receive_seq=13341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997494 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33571 bytes_read=1367340 bytes_retransmit=9 bytes_invalid=0 send_seq=5536 receive_seq=5536 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34057 bytes_read=102529 bytes_retransmit=9 bytes_invalid=0 send_seq=5523 receive_seq=5523 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88149 bytes_read=2134947 bytes_retransmit=0 bytes_invalid=0 send_seq=10082 receive_seq=10082 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998657 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=54.0 th1: temp=55.8 th2: temp=60.4 th3: temp=57.9 sysload=0.08 cputime=389.545 memavail=7393916 print_time=5384.138 buffer_time=2.156 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 81 Hz
Stats 5360.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24558349 bytes_read=3798874 bytes_retransmit=9 bytes_invalid=0 send_seq=461192 receive_seq=461192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015842 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33310 bytes_read=104591 bytes_retransmit=0 bytes_invalid=0 send_seq=5523 receive_seq=5523 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997264 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168926 bytes_read=5287890 bytes_retransmit=9 bytes_invalid=0 send_seq=23287 receive_seq=23287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997704 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98692 bytes_read=2316569 bytes_retransmit=9 bytes_invalid=0 send_seq=13352 receive_seq=13352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997493 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33577 bytes_read=1367634 bytes_retransmit=9 bytes_invalid=0 send_seq=5537 receive_seq=5537 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997611 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34063 bytes_read=102545 bytes_retransmit=9 bytes_invalid=0 send_seq=5524 receive_seq=5524 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88155 bytes_read=2135303 bytes_retransmit=0 bytes_invalid=0 send_seq=10083 receive_seq=10083 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998639 coil_temp=17.0 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=54.1 th1: temp=55.5 th2: temp=60.3 th3: temp=58.0 sysload=0.07 cputime=389.636 memavail=7393916 print_time=5385.010 buffer_time=2.025 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 82 Hz
Stats 5361.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24562424 bytes_read=3799620 bytes_retransmit=9 bytes_invalid=0 send_seq=461276 receive_seq=461276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015844 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33316 bytes_read=104607 bytes_retransmit=0 bytes_invalid=0 send_seq=5524 receive_seq=5524 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997242 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168932 bytes_read=5287990 bytes_retransmit=9 bytes_invalid=0 send_seq=23288 receive_seq=23288 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997726 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98768 bytes_read=2319684 bytes_retransmit=9 bytes_invalid=0 send_seq=13363 receive_seq=13363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997472 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33583 bytes_read=1367868 bytes_retransmit=9 bytes_invalid=0 send_seq=5538 receive_seq=5538 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997603 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34069 bytes_read=102561 bytes_retransmit=9 bytes_invalid=0 send_seq=5525 receive_seq=5525 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88161 bytes_read=2135659 bytes_retransmit=0 bytes_invalid=0 send_seq=10084 receive_seq=10084 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998640 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=54.2 th1: temp=55.4 th2: temp=60.3 th3: temp=58.1 sysload=0.07 cputime=389.737 memavail=7393916 print_time=5386.212 buffer_time=2.224 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 83 Hz
Stats 5362.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24565772 bytes_read=3800319 bytes_retransmit=9 bytes_invalid=0 send_seq=461348 receive_seq=461348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015838 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33322 bytes_read=104623 bytes_retransmit=0 bytes_invalid=0 send_seq=5525 receive_seq=5525 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997236 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168938 bytes_read=5288118 bytes_retransmit=9 bytes_invalid=0 send_seq=23289 receive_seq=23289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997680 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98844 bytes_read=2322754 bytes_retransmit=9 bytes_invalid=0 send_seq=13374 receive_seq=13374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997470 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33589 bytes_read=1368102 bytes_retransmit=9 bytes_invalid=0 send_seq=5539 receive_seq=5539 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997612 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34075 bytes_read=102588 bytes_retransmit=9 bytes_invalid=0 send_seq=5526 receive_seq=5526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88167 bytes_read=2136015 bytes_retransmit=0 bytes_invalid=0 send_seq=10085 receive_seq=10085 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998642 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=53.9 th1: temp=55.8 th2: temp=60.4 th3: temp=57.9 sysload=0.07 cputime=389.828 memavail=7393916 print_time=5387.152 buffer_time=2.162 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 84 Hz
Stats 5363.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24568810 bytes_read=3800954 bytes_retransmit=9 bytes_invalid=0 send_seq=461413 receive_seq=461413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015836 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33328 bytes_read=104639 bytes_retransmit=0 bytes_invalid=0 send_seq=5526 receive_seq=5526 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997250 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168944 bytes_read=5288218 bytes_retransmit=9 bytes_invalid=0 send_seq=23290 receive_seq=23290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997663 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98920 bytes_read=2325826 bytes_retransmit=9 bytes_invalid=0 send_seq=13385 receive_seq=13385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33595 bytes_read=1368411 bytes_retransmit=9 bytes_invalid=0 send_seq=5540 receive_seq=5540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997629 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34081 bytes_read=102604 bytes_retransmit=9 bytes_invalid=0 send_seq=5527 receive_seq=5527 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88173 bytes_read=2136371 bytes_retransmit=0 bytes_invalid=0 send_seq=10086 receive_seq=10086 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998659 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=54.3 th1: temp=55.8 th2: temp=60.5 th3: temp=58.0 sysload=0.07 cputime=389.920 memavail=7393916 print_time=5388.025 buffer_time=2.032 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 85 Hz
Stats 5364.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24572992 bytes_read=3801684 bytes_retransmit=9 bytes_invalid=0 send_seq=461497 receive_seq=461497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015842 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33334 bytes_read=104655 bytes_retransmit=0 bytes_invalid=0 send_seq=5527 receive_seq=5527 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997254 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168950 bytes_read=5288332 bytes_retransmit=9 bytes_invalid=0 send_seq=23291 receive_seq=23291 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997639 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=98996 bytes_read=2328900 bytes_retransmit=9 bytes_invalid=0 send_seq=13396 receive_seq=13396 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997475 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33601 bytes_read=1368645 bytes_retransmit=9 bytes_invalid=0 send_seq=5541 receive_seq=5541 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34087 bytes_read=102620 bytes_retransmit=9 bytes_invalid=0 send_seq=5528 receive_seq=5528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88179 bytes_read=2136727 bytes_retransmit=0 bytes_invalid=0 send_seq=10087 receive_seq=10087 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998660 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=54.2 th1: temp=55.8 th2: temp=60.4 th3: temp=58.0 sysload=0.07 cputime=390.018 memavail=7393916 print_time=5389.216 buffer_time=2.223 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 86 Hz
Stats 5365.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24576435 bytes_read=3802363 bytes_retransmit=9 bytes_invalid=0 send_seq=461565 receive_seq=461565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015829 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=33340 bytes_read=104684 bytes_retransmit=0 bytes_invalid=0 send_seq=5528 receive_seq=5528 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997239 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168956 bytes_read=5288460 bytes_retransmit=9 bytes_invalid=0 send_seq=23292 receive_seq=23292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997627 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99072 bytes_read=2331989 bytes_retransmit=9 bytes_invalid=0 send_seq=13407 receive_seq=13407 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997478 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33607 bytes_read=1368879 bytes_retransmit=9 bytes_invalid=0 send_seq=5542 receive_seq=5542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997630 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34093 bytes_read=102636 bytes_retransmit=9 bytes_invalid=0 send_seq=5529 receive_seq=5529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88185 bytes_read=2137083 bytes_retransmit=0 bytes_invalid=0 send_seq=10088 receive_seq=10088 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998662 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=54.5 th1: temp=56.1 th2: temp=60.3 th3: temp=58.0 sysload=0.07 cputime=390.111 memavail=7393916 print_time=5390.158 buffer_time=2.165 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 87 Hz
Stats 5366.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24579425 bytes_read=3803009 bytes_retransmit=9 bytes_invalid=0 send_seq=461629 receive_seq=461629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015845 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=33346 bytes_read=104700 bytes_retransmit=0 bytes_invalid=0 send_seq=5529 receive_seq=5529 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997252 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168962 bytes_read=5288560 bytes_retransmit=9 bytes_invalid=0 send_seq=23293 receive_seq=23293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997654 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99148 bytes_read=2335047 bytes_retransmit=9 bytes_invalid=0 send_seq=13418 receive_seq=13418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33613 bytes_read=1369173 bytes_retransmit=9 bytes_invalid=0 send_seq=5543 receive_seq=5543 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997696 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34099 bytes_read=102652 bytes_retransmit=9 bytes_invalid=0 send_seq=5530 receive_seq=5530 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88191 bytes_read=2137439 bytes_retransmit=0 bytes_invalid=0 send_seq=10089 receive_seq=10089 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998667 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=54.1 th1: temp=55.7 th2: temp=60.5 th3: temp=58.0 sysload=0.07 cputime=390.204 memavail=7393916 print_time=5391.027 buffer_time=2.034 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 88 Hz
Stats 5367.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24583615 bytes_read=3803742 bytes_retransmit=9 bytes_invalid=0 send_seq=461714 receive_seq=461714 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015850 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=33352 bytes_read=104716 bytes_retransmit=0 bytes_invalid=0 send_seq=5530 receive_seq=5530 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997226 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168968 bytes_read=5288660 bytes_retransmit=9 bytes_invalid=0 send_seq=23294 receive_seq=23294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997681 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99224 bytes_read=2338161 bytes_retransmit=9 bytes_invalid=0 send_seq=13429 receive_seq=13429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997463 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33619 bytes_read=1369407 bytes_retransmit=9 bytes_invalid=0 send_seq=5544 receive_seq=5544 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34105 bytes_read=102679 bytes_retransmit=9 bytes_invalid=0 send_seq=5531 receive_seq=5531 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88197 bytes_read=2137795 bytes_retransmit=0 bytes_invalid=0 send_seq=10090 receive_seq=10090 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998658 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=54.0 th1: temp=55.8 th2: temp=60.5 th3: temp=58.1 sysload=0.07 cputime=390.310 memavail=7395240 print_time=5392.229 buffer_time=2.235 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 89 Hz
Stats 5368.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24587149 bytes_read=3804451 bytes_retransmit=9 bytes_invalid=0 send_seq=461789 receive_seq=461789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015842 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=33358 bytes_read=104732 bytes_retransmit=0 bytes_invalid=0 send_seq=5531 receive_seq=5531 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997237 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168974 bytes_read=5288788 bytes_retransmit=9 bytes_invalid=0 send_seq=23295 receive_seq=23295 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997643 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99293 bytes_read=2341223 bytes_retransmit=9 bytes_invalid=0 send_seq=13439 receive_seq=13439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997460 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33625 bytes_read=1369656 bytes_retransmit=9 bytes_invalid=0 send_seq=5545 receive_seq=5545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34111 bytes_read=102695 bytes_retransmit=9 bytes_invalid=0 send_seq=5532 receive_seq=5532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88203 bytes_read=2138151 bytes_retransmit=0 bytes_invalid=0 send_seq=10091 receive_seq=10091 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998649 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=54.1 th1: temp=55.8 th2: temp=60.5 th3: temp=58.0 sysload=0.07 cputime=390.408 memavail=7394988 print_time=5393.162 buffer_time=2.167 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 90 Hz
Stats 5369.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24590171 bytes_read=3805091 bytes_retransmit=9 bytes_invalid=0 send_seq=461855 receive_seq=461855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015839 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=33364 bytes_read=104748 bytes_retransmit=0 bytes_invalid=0 send_seq=5532 receive_seq=5532 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997257 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168980 bytes_read=5288902 bytes_retransmit=9 bytes_invalid=0 send_seq=23296 receive_seq=23296 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997650 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99369 bytes_read=2344296 bytes_retransmit=9 bytes_invalid=0 send_seq=13450 receive_seq=13450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33631 bytes_read=1369950 bytes_retransmit=9 bytes_invalid=0 send_seq=5546 receive_seq=5546 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34117 bytes_read=102711 bytes_retransmit=9 bytes_invalid=0 send_seq=5533 receive_seq=5533 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88209 bytes_read=2138507 bytes_retransmit=0 bytes_invalid=0 send_seq=10092 receive_seq=10092 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998691 coil_temp=17.0 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=54.2 th1: temp=55.7 th2: temp=60.5 th3: temp=58.0 sysload=0.07 cputime=390.506 memavail=7394988 print_time=5394.035 buffer_time=2.040 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 91 Hz
Stats 5370.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=24594472 bytes_read=3805831 bytes_retransmit=9 bytes_invalid=0 send_seq=461941 receive_seq=461941 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015842 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33370 bytes_read=104777 bytes_retransmit=0 bytes_invalid=0 send_seq=5533 receive_seq=5533 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997265 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168986 bytes_read=5289002 bytes_retransmit=9 bytes_invalid=0 send_seq=23297 receive_seq=23297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997634 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99445 bytes_read=2347354 bytes_retransmit=9 bytes_invalid=0 send_seq=13461 receive_seq=13461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997478 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33637 bytes_read=1370184 bytes_retransmit=9 bytes_invalid=0 send_seq=5547 receive_seq=5547 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34123 bytes_read=102727 bytes_retransmit=9 bytes_invalid=0 send_seq=5534 receive_seq=5534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88215 bytes_read=2138863 bytes_retransmit=0 bytes_invalid=0 send_seq=10093 receive_seq=10093 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998694 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=54.3 th1: temp=55.8 th2: temp=60.5 th3: temp=58.0 sysload=0.06 cputime=390.612 memavail=7394772 print_time=5395.228 buffer_time=2.232 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 92 Hz
Stats 5371.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24598125 bytes_read=3806571 bytes_retransmit=9 bytes_invalid=0 send_seq=462018 receive_seq=462018 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015833 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33376 bytes_read=104793 bytes_retransmit=0 bytes_invalid=0 send_seq=5534 receive_seq=5534 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997262 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168992 bytes_read=5289130 bytes_retransmit=9 bytes_invalid=0 send_seq=23298 receive_seq=23298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997858 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99521 bytes_read=2350438 bytes_retransmit=9 bytes_invalid=0 send_seq=13472 receive_seq=13472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997489 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33643 bytes_read=1370418 bytes_retransmit=9 bytes_invalid=0 send_seq=5548 receive_seq=5548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34129 bytes_read=102743 bytes_retransmit=9 bytes_invalid=0 send_seq=5535 receive_seq=5535 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88221 bytes_read=2139219 bytes_retransmit=0 bytes_invalid=0 send_seq=10094 receive_seq=10094 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998712 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=54.1 th1: temp=55.9 th2: temp=60.4 th3: temp=58.1 sysload=0.06 cputime=390.709 memavail=7394772 print_time=5396.171 buffer_time=2.174 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 93 Hz
Stats 5372.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24601175 bytes_read=3807211 bytes_retransmit=9 bytes_invalid=0 send_seq=462084 receive_seq=462084 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015827 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33382 bytes_read=104809 bytes_retransmit=0 bytes_invalid=0 send_seq=5535 receive_seq=5535 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997275 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=168998 bytes_read=5289230 bytes_retransmit=9 bytes_invalid=0 send_seq=23299 receive_seq=23299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997826 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99597 bytes_read=2353496 bytes_retransmit=9 bytes_invalid=0 send_seq=13483 receive_seq=13483 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997499 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33649 bytes_read=1370712 bytes_retransmit=9 bytes_invalid=0 send_seq=5549 receive_seq=5549 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34135 bytes_read=102770 bytes_retransmit=9 bytes_invalid=0 send_seq=5536 receive_seq=5536 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88227 bytes_read=2139575 bytes_retransmit=0 bytes_invalid=0 send_seq=10095 receive_seq=10095 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998759 coil_temp=17.0 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=54.1 th1: temp=55.7 th2: temp=60.5 th3: temp=58.1 sysload=0.06 cputime=390.806 memavail=7394780 print_time=5397.043 buffer_time=2.046 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 94 Hz
Stats 5373.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24605550 bytes_read=3807961 bytes_retransmit=9 bytes_invalid=0 send_seq=462172 receive_seq=462172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015820 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33388 bytes_read=104825 bytes_retransmit=0 bytes_invalid=0 send_seq=5536 receive_seq=5536 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997284 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169004 bytes_read=5289330 bytes_retransmit=9 bytes_invalid=0 send_seq=23300 receive_seq=23300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997822 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99673 bytes_read=2356553 bytes_retransmit=9 bytes_invalid=0 send_seq=13494 receive_seq=13494 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33655 bytes_read=1370961 bytes_retransmit=9 bytes_invalid=0 send_seq=5550 receive_seq=5550 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997679 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34141 bytes_read=102786 bytes_retransmit=9 bytes_invalid=0 send_seq=5537 receive_seq=5537 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88233 bytes_read=2139931 bytes_retransmit=0 bytes_invalid=0 send_seq=10096 receive_seq=10096 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998742 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=54.1 th1: temp=55.8 th2: temp=60.4 th3: temp=58.2 sysload=0.06 cputime=390.913 memavail=7394780 print_time=5398.247 buffer_time=2.251 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 95 Hz
Stats 5374.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24609272 bytes_read=3808695 bytes_retransmit=9 bytes_invalid=0 send_seq=462251 receive_seq=462251 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015825 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33394 bytes_read=104841 bytes_retransmit=0 bytes_invalid=0 send_seq=5537 receive_seq=5537 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997313 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=169010 bytes_read=5289472 bytes_retransmit=9 bytes_invalid=0 send_seq=23301 receive_seq=23301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000248 adj=63997839 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99749 bytes_read=2359656 bytes_retransmit=9 bytes_invalid=0 send_seq=13505 receive_seq=13505 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997526 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33661 bytes_read=1371195 bytes_retransmit=9 bytes_invalid=0 send_seq=5551 receive_seq=5551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997694 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34147 bytes_read=102802 bytes_retransmit=9 bytes_invalid=0 send_seq=5538 receive_seq=5538 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88239 bytes_read=2140287 bytes_retransmit=0 bytes_invalid=0 send_seq=10097 receive_seq=10097 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998761 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=54.8 th1: temp=55.6 th2: temp=60.5 th3: temp=58.1 sysload=0.06 cputime=391.017 memavail=7389000 print_time=5399.184 buffer_time=2.187 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 96 Hz
Stats 5375.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24612291 bytes_read=3809346 bytes_retransmit=9 bytes_invalid=0 send_seq=462317 receive_seq=462317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015819 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33406 bytes_read=104886 bytes_retransmit=0 bytes_invalid=0 send_seq=5539 receive_seq=5539 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997312 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=169022 bytes_read=5289588 bytes_retransmit=9 bytes_invalid=0 send_seq=23303 receive_seq=23303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997952 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99831 bytes_read=2362786 bytes_retransmit=9 bytes_invalid=0 send_seq=13517 receive_seq=13517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997518 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33673 bytes_read=1371505 bytes_retransmit=9 bytes_invalid=0 send_seq=5553 receive_seq=5553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34159 bytes_read=102834 bytes_retransmit=9 bytes_invalid=0 send_seq=5540 receive_seq=5540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88251 bytes_read=2140659 bytes_retransmit=0 bytes_invalid=0 send_seq=10099 receive_seq=10099 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998731 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=54.1 th1: temp=55.8 th2: temp=60.5 th3: temp=58.2 sysload=0.06 cputime=391.122 memavail=7394900 print_time=5400.050 buffer_time=2.052 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 97 Hz
Stats 5376.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24616724 bytes_read=3810122 bytes_retransmit=9 bytes_invalid=0 send_seq=462407 receive_seq=462407 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015821 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33412 bytes_read=104902 bytes_retransmit=0 bytes_invalid=0 send_seq=5540 receive_seq=5540 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997304 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=169028 bytes_read=5289688 bytes_retransmit=9 bytes_invalid=0 send_seq=23304 receive_seq=23304 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997843 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99907 bytes_read=2365844 bytes_retransmit=9 bytes_invalid=0 send_seq=13528 receive_seq=13528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997533 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33679 bytes_read=1371739 bytes_retransmit=9 bytes_invalid=0 send_seq=5554 receive_seq=5554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997747 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34165 bytes_read=102850 bytes_retransmit=9 bytes_invalid=0 send_seq=5541 receive_seq=5541 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88257 bytes_read=2141015 bytes_retransmit=0 bytes_invalid=0 send_seq=10100 receive_seq=10100 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998708 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=54.0 th1: temp=55.8 th2: temp=60.5 th3: temp=58.0 sysload=0.06 cputime=391.236 memavail=7394908 print_time=5401.256 buffer_time=2.257 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 98 Hz
Stats 5377.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24620532 bytes_read=3810861 bytes_retransmit=9 bytes_invalid=0 send_seq=462487 receive_seq=462487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015832 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33418 bytes_read=104918 bytes_retransmit=0 bytes_invalid=0 send_seq=5541 receive_seq=5541 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997276 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=169034 bytes_read=5289816 bytes_retransmit=9 bytes_invalid=0 send_seq=23305 receive_seq=23305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997777 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=99983 bytes_read=2368930 bytes_retransmit=9 bytes_invalid=0 send_seq=13539 receive_seq=13539 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997516 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33685 bytes_read=1371988 bytes_retransmit=9 bytes_invalid=0 send_seq=5555 receive_seq=5555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997719 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34171 bytes_read=102877 bytes_retransmit=9 bytes_invalid=0 send_seq=5542 receive_seq=5542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88263 bytes_read=2141371 bytes_retransmit=0 bytes_invalid=0 send_seq=10101 receive_seq=10101 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998685 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=54.4 th1: temp=55.9 th2: temp=60.4 th3: temp=58.1 sysload=0.06 cputime=391.340 memavail=7396728 print_time=5402.184 buffer_time=2.185 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 99 Hz
Stats 5378.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24623603 bytes_read=3811506 bytes_retransmit=9 bytes_invalid=0 send_seq=462555 receive_seq=462555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015832 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33424 bytes_read=104934 bytes_retransmit=0 bytes_invalid=0 send_seq=5542 receive_seq=5542 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997246 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=169040 bytes_read=5289916 bytes_retransmit=9 bytes_invalid=0 send_seq=23306 receive_seq=23306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997767 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100059 bytes_read=2371987 bytes_retransmit=9 bytes_invalid=0 send_seq=13550 receive_seq=13550 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33691 bytes_read=1372282 bytes_retransmit=9 bytes_invalid=0 send_seq=5556 receive_seq=5556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997692 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34177 bytes_read=102893 bytes_retransmit=9 bytes_invalid=0 send_seq=5543 receive_seq=5543 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88269 bytes_read=2141727 bytes_retransmit=0 bytes_invalid=0 send_seq=10102 receive_seq=10102 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998661 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.012 th0: temp=54.2 th1: temp=55.8 th2: temp=60.5 th3: temp=58.1 sysload=0.06 cputime=391.440 memavail=7396728 print_time=5403.051 buffer_time=2.051 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 100 Hz
Stats 5379.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24628073 bytes_read=3812261 bytes_retransmit=9 bytes_invalid=0 send_seq=462644 receive_seq=462644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015827 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33430 bytes_read=104950 bytes_retransmit=0 bytes_invalid=0 send_seq=5543 receive_seq=5543 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997241 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169046 bytes_read=5290030 bytes_retransmit=9 bytes_invalid=0 send_seq=23307 receive_seq=23307 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997720 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100135 bytes_read=2375060 bytes_retransmit=9 bytes_invalid=0 send_seq=13561 receive_seq=13561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997489 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33697 bytes_read=1372516 bytes_retransmit=9 bytes_invalid=0 send_seq=5557 receive_seq=5557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34183 bytes_read=102909 bytes_retransmit=9 bytes_invalid=0 send_seq=5544 receive_seq=5544 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88275 bytes_read=2142083 bytes_retransmit=0 bytes_invalid=0 send_seq=10103 receive_seq=10103 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998650 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=54.3 th1: temp=55.8 th2: temp=60.3 th3: temp=58.0 sysload=0.06 cputime=391.553 memavail=7396728 print_time=5404.258 buffer_time=2.257 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 101 Hz
Stats 5380.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24631970 bytes_read=3813000 bytes_retransmit=9 bytes_invalid=0 send_seq=462724 receive_seq=462724 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015844 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=33436 bytes_read=104979 bytes_retransmit=0 bytes_invalid=0 send_seq=5544 receive_seq=5544 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997255 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169052 bytes_read=5290158 bytes_retransmit=9 bytes_invalid=0 send_seq=23308 receive_seq=23308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997683 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100211 bytes_read=2378145 bytes_retransmit=9 bytes_invalid=0 send_seq=13572 receive_seq=13572 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997501 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33703 bytes_read=1372765 bytes_retransmit=9 bytes_invalid=0 send_seq=5558 receive_seq=5558 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34189 bytes_read=102925 bytes_retransmit=9 bytes_invalid=0 send_seq=5545 receive_seq=5545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88281 bytes_read=2142439 bytes_retransmit=0 bytes_invalid=0 send_seq=10104 receive_seq=10104 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998654 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=54.1 th1: temp=55.8 th2: temp=60.6 th3: temp=58.1 sysload=0.13 cputime=391.658 memavail=7396484 print_time=5405.186 buffer_time=2.184 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 102 Hz
Stats 5381.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24635113 bytes_read=3813671 bytes_retransmit=9 bytes_invalid=0 send_seq=462793 receive_seq=462793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015841 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=33442 bytes_read=104995 bytes_retransmit=0 bytes_invalid=0 send_seq=5545 receive_seq=5545 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997219 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169058 bytes_read=5290258 bytes_retransmit=9 bytes_invalid=0 send_seq=23309 receive_seq=23309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997613 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100287 bytes_read=2381201 bytes_retransmit=9 bytes_invalid=0 send_seq=13583 receive_seq=13583 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997465 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33709 bytes_read=1373044 bytes_retransmit=9 bytes_invalid=0 send_seq=5559 receive_seq=5559 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997713 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34195 bytes_read=102941 bytes_retransmit=9 bytes_invalid=0 send_seq=5546 receive_seq=5546 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88287 bytes_read=2142795 bytes_retransmit=0 bytes_invalid=0 send_seq=10105 receive_seq=10105 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998636 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=54.7 th1: temp=55.6 th2: temp=60.5 th3: temp=58.1 sysload=0.13 cputime=391.754 memavail=7396484 print_time=5406.064 buffer_time=2.062 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 103 Hz
Stats 5382.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24639602 bytes_read=3814375 bytes_retransmit=9 bytes_invalid=0 send_seq=462880 receive_seq=462877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=0 freq=400015843 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=33448 bytes_read=105011 bytes_retransmit=0 bytes_invalid=0 send_seq=5546 receive_seq=5546 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997240 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169064 bytes_read=5290358 bytes_retransmit=9 bytes_invalid=0 send_seq=23310 receive_seq=23310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997620 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100363 bytes_read=2384315 bytes_retransmit=9 bytes_invalid=0 send_seq=13594 receive_seq=13594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997474 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33715 bytes_read=1373278 bytes_retransmit=9 bytes_invalid=0 send_seq=5560 receive_seq=5560 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997700 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34201 bytes_read=102968 bytes_retransmit=9 bytes_invalid=0 send_seq=5547 receive_seq=5547 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88293 bytes_read=2143151 bytes_retransmit=0 bytes_invalid=0 send_seq=10106 receive_seq=10106 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998667 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=54.1 th1: temp=55.9 th2: temp=60.5 th3: temp=57.9 sysload=0.13 cputime=391.860 memavail=7396484 print_time=5407.266 buffer_time=2.259 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 104 Hz
Stats 5383.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24643647 bytes_read=3815144 bytes_retransmit=9 bytes_invalid=0 send_seq=462963 receive_seq=462963 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015837 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=33454 bytes_read=105027 bytes_retransmit=0 bytes_invalid=0 send_seq=5547 receive_seq=5547 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997243 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169070 bytes_read=5290486 bytes_retransmit=9 bytes_invalid=0 send_seq=23311 receive_seq=23311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997627 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100439 bytes_read=2387401 bytes_retransmit=9 bytes_invalid=0 send_seq=13605 receive_seq=13605 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33721 bytes_read=1373542 bytes_retransmit=9 bytes_invalid=0 send_seq=5561 receive_seq=5561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34207 bytes_read=102984 bytes_retransmit=9 bytes_invalid=0 send_seq=5548 receive_seq=5548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88299 bytes_read=2143507 bytes_retransmit=0 bytes_invalid=0 send_seq=10107 receive_seq=10107 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998657 coil_temp=17.0 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=54.2 th1: temp=55.8 th2: temp=60.5 th3: temp=58.1 sysload=0.13 cputime=391.959 memavail=7396484 print_time=5408.198 buffer_time=2.190 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 105 Hz
Stats 5384.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24646793 bytes_read=3815789 bytes_retransmit=9 bytes_invalid=0 send_seq=463030 receive_seq=463030 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015832 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=33460 bytes_read=105043 bytes_retransmit=0 bytes_invalid=0 send_seq=5548 receive_seq=5548 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997253 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169076 bytes_read=5290600 bytes_retransmit=9 bytes_invalid=0 send_seq=23312 receive_seq=23312 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997618 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100508 bytes_read=2390451 bytes_retransmit=9 bytes_invalid=0 send_seq=13615 receive_seq=13615 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997488 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33727 bytes_read=1373821 bytes_retransmit=9 bytes_invalid=0 send_seq=5562 receive_seq=5562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34213 bytes_read=103000 bytes_retransmit=9 bytes_invalid=0 send_seq=5549 receive_seq=5549 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88305 bytes_read=2143863 bytes_retransmit=0 bytes_invalid=0 send_seq=10108 receive_seq=10108 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998658 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=54.4 th1: temp=55.8 th2: temp=60.5 th3: temp=57.9 sysload=0.13 cputime=392.055 memavail=7396484 print_time=5409.063 buffer_time=2.055 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 106 Hz
Stats 5385.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24651373 bytes_read=3816549 bytes_retransmit=9 bytes_invalid=0 send_seq=463122 receive_seq=463120 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=0 freq=400015830 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33466 bytes_read=105072 bytes_retransmit=0 bytes_invalid=0 send_seq=5549 receive_seq=5549 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997275 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169082 bytes_read=5290700 bytes_retransmit=9 bytes_invalid=0 send_seq=23313 receive_seq=23313 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997603 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100584 bytes_read=2393508 bytes_retransmit=9 bytes_invalid=0 send_seq=13626 receive_seq=13626 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997501 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33733 bytes_read=1374055 bytes_retransmit=9 bytes_invalid=0 send_seq=5563 receive_seq=5563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34219 bytes_read=103016 bytes_retransmit=9 bytes_invalid=0 send_seq=5550 receive_seq=5550 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88311 bytes_read=2144219 bytes_retransmit=0 bytes_invalid=0 send_seq=10109 receive_seq=10109 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998664 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.8 th2: temp=60.4 th3: temp=58.2 sysload=0.12 cputime=392.163 memavail=7396500 print_time=5410.270 buffer_time=2.259 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 107 Hz
Stats 5386.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24655471 bytes_read=3817329 bytes_retransmit=9 bytes_invalid=0 send_seq=463205 receive_seq=463205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=400015828 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33472 bytes_read=105088 bytes_retransmit=0 bytes_invalid=0 send_seq=5550 receive_seq=5550 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997278 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169088 bytes_read=5290828 bytes_retransmit=9 bytes_invalid=0 send_seq=23314 receive_seq=23314 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997734 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100660 bytes_read=2396592 bytes_retransmit=9 bytes_invalid=0 send_seq=13637 receive_seq=13637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33739 bytes_read=1374319 bytes_retransmit=9 bytes_invalid=0 send_seq=5564 receive_seq=5564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34225 bytes_read=103032 bytes_retransmit=9 bytes_invalid=0 send_seq=5551 receive_seq=5551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999471 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88317 bytes_read=2144575 bytes_retransmit=0 bytes_invalid=0 send_seq=10110 receive_seq=10110 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998657 coil_temp=17.0 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=54.1 th1: temp=55.8 th2: temp=60.5 th3: temp=58.1 sysload=0.12 cputime=392.264 memavail=7396500 print_time=5411.200 buffer_time=2.188 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 108 Hz
Stats 5387.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24658696 bytes_read=3817989 bytes_retransmit=9 bytes_invalid=0 send_seq=463275 receive_seq=463275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015827 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33478 bytes_read=105104 bytes_retransmit=0 bytes_invalid=0 send_seq=5551 receive_seq=5551 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997280 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169094 bytes_read=5290928 bytes_retransmit=9 bytes_invalid=0 send_seq=23315 receive_seq=23315 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997700 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100736 bytes_read=2399706 bytes_retransmit=9 bytes_invalid=0 send_seq=13648 receive_seq=13648 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33745 bytes_read=1374583 bytes_retransmit=9 bytes_invalid=0 send_seq=5565 receive_seq=5565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34231 bytes_read=103059 bytes_retransmit=9 bytes_invalid=0 send_seq=5552 receive_seq=5552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88323 bytes_read=2144931 bytes_retransmit=0 bytes_invalid=0 send_seq=10111 receive_seq=10111 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998667 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=54.2 th1: temp=55.6 th2: temp=60.4 th3: temp=58.1 sysload=0.12 cputime=392.365 memavail=7395536 print_time=5412.076 buffer_time=2.064 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 109 Hz
Stats 5388.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24663415 bytes_read=3818774 bytes_retransmit=9 bytes_invalid=0 send_seq=463370 receive_seq=463370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015821 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33484 bytes_read=105120 bytes_retransmit=0 bytes_invalid=0 send_seq=5552 receive_seq=5552 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997271 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169100 bytes_read=5291028 bytes_retransmit=9 bytes_invalid=0 send_seq=23316 receive_seq=23316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997665 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100812 bytes_read=2402765 bytes_retransmit=9 bytes_invalid=0 send_seq=13659 receive_seq=13659 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997518 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33751 bytes_read=1374832 bytes_retransmit=9 bytes_invalid=0 send_seq=5566 receive_seq=5566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34237 bytes_read=103075 bytes_retransmit=9 bytes_invalid=0 send_seq=5553 receive_seq=5553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88329 bytes_read=2145287 bytes_retransmit=0 bytes_invalid=0 send_seq=10112 receive_seq=10112 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998662 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=54.4 th1: temp=55.8 th2: temp=60.6 th3: temp=58.1 sysload=0.12 cputime=392.477 memavail=7395536 print_time=5413.275 buffer_time=2.262 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 110 Hz
Stats 5389.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24667557 bytes_read=3819533 bytes_retransmit=9 bytes_invalid=0 send_seq=463455 receive_seq=463455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=400015817 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33490 bytes_read=105136 bytes_retransmit=0 bytes_invalid=0 send_seq=5553 receive_seq=5553 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997275 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169106 bytes_read=5291170 bytes_retransmit=9 bytes_invalid=0 send_seq=23317 receive_seq=23317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997648 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100888 bytes_read=2405866 bytes_retransmit=9 bytes_invalid=0 send_seq=13670 receive_seq=13670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997848 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33757 bytes_read=1375096 bytes_retransmit=9 bytes_invalid=0 send_seq=5567 receive_seq=5567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34243 bytes_read=103091 bytes_retransmit=9 bytes_invalid=0 send_seq=5554 receive_seq=5554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88335 bytes_read=2145643 bytes_retransmit=0 bytes_invalid=0 send_seq=10113 receive_seq=10113 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998660 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.8 th2: temp=60.5 th3: temp=58.1 sysload=0.12 cputime=392.580 memavail=7395044 print_time=5414.204 buffer_time=2.191 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 111 Hz
Stats 5390.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24670795 bytes_read=3820193 bytes_retransmit=9 bytes_invalid=0 send_seq=463525 receive_seq=463525 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015834 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33496 bytes_read=105165 bytes_retransmit=0 bytes_invalid=0 send_seq=5554 receive_seq=5554 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997280 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169112 bytes_read=5291270 bytes_retransmit=9 bytes_invalid=0 send_seq=23318 receive_seq=23318 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997631 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=100964 bytes_read=2408923 bytes_retransmit=9 bytes_invalid=0 send_seq=13681 receive_seq=13681 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997796 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33763 bytes_read=1375360 bytes_retransmit=9 bytes_invalid=0 send_seq=5568 receive_seq=5568 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34249 bytes_read=103107 bytes_retransmit=9 bytes_invalid=0 send_seq=5555 receive_seq=5555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88341 bytes_read=2145999 bytes_retransmit=0 bytes_invalid=0 send_seq=10114 receive_seq=10114 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998663 coil_temp=17.0 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.7 th2: temp=60.2 th3: temp=58.1 sysload=0.11 cputime=392.680 memavail=7395044 print_time=5415.074 buffer_time=2.060 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 112 Hz
Stats 5391.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24675528 bytes_read=3820984 bytes_retransmit=9 bytes_invalid=0 send_seq=463618 receive_seq=463618 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=400015852 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33502 bytes_read=105181 bytes_retransmit=0 bytes_invalid=0 send_seq=5555 receive_seq=5555 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997239 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169118 bytes_read=5291370 bytes_retransmit=9 bytes_invalid=0 send_seq=23319 receive_seq=23319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997571 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101040 bytes_read=2411980 bytes_retransmit=9 bytes_invalid=0 send_seq=13692 receive_seq=13692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997715 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33769 bytes_read=1375594 bytes_retransmit=9 bytes_invalid=0 send_seq=5569 receive_seq=5569 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34255 bytes_read=103123 bytes_retransmit=9 bytes_invalid=0 send_seq=5556 receive_seq=5556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88347 bytes_read=2146355 bytes_retransmit=0 bytes_invalid=0 send_seq=10115 receive_seq=10115 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998649 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=54.5 th1: temp=55.7 th2: temp=60.5 th3: temp=58.1 sysload=0.11 cputime=392.793 memavail=7394036 print_time=5416.279 buffer_time=2.265 print_stall=0 extruder: target=0 temp=19.4 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 113 Hz
Stats 5392.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24679674 bytes_read=3821748 bytes_retransmit=9 bytes_invalid=0 send_seq=463703 receive_seq=463703 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015845 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33508 bytes_read=105197 bytes_retransmit=0 bytes_invalid=0 send_seq=5556 receive_seq=5556 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997215 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169124 bytes_read=5291498 bytes_retransmit=9 bytes_invalid=0 send_seq=23320 receive_seq=23320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997626 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101116 bytes_read=2415065 bytes_retransmit=9 bytes_invalid=0 send_seq=13703 receive_seq=13703 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997604 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33775 bytes_read=1375858 bytes_retransmit=9 bytes_invalid=0 send_seq=5570 receive_seq=5570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997606 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34261 bytes_read=103150 bytes_retransmit=9 bytes_invalid=0 send_seq=5557 receive_seq=5557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88353 bytes_read=2146711 bytes_retransmit=0 bytes_invalid=0 send_seq=10116 receive_seq=10116 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998665 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.7 th2: temp=60.5 th3: temp=58.1 sysload=0.11 cputime=392.903 memavail=7394652 print_time=5417.214 buffer_time=2.200 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 114 Hz
Stats 5393.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24682975 bytes_read=3822408 bytes_retransmit=9 bytes_invalid=0 send_seq=463773 receive_seq=463773 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015839 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33514 bytes_read=105213 bytes_retransmit=0 bytes_invalid=0 send_seq=5557 receive_seq=5557 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997225 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169130 bytes_read=5291598 bytes_retransmit=9 bytes_invalid=0 send_seq=23321 receive_seq=23321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997619 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101192 bytes_read=2418121 bytes_retransmit=9 bytes_invalid=0 send_seq=13714 receive_seq=13714 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997592 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33781 bytes_read=1376137 bytes_retransmit=9 bytes_invalid=0 send_seq=5571 receive_seq=5571 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997617 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34267 bytes_read=103166 bytes_retransmit=9 bytes_invalid=0 send_seq=5558 receive_seq=5558 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88359 bytes_read=2147067 bytes_retransmit=0 bytes_invalid=0 send_seq=10117 receive_seq=10117 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998667 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=54.2 th1: temp=55.8 th2: temp=60.5 th3: temp=58.0 sysload=0.11 cputime=393.005 memavail=7394652 print_time=5418.085 buffer_time=2.070 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Testing frequency 115 Hz
Stats 5394.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24687180 bytes_read=3823143 bytes_retransmit=9 bytes_invalid=0 send_seq=463858 receive_seq=463858 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015839 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33520 bytes_read=105229 bytes_retransmit=0 bytes_invalid=0 send_seq=5558 receive_seq=5558 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997227 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169136 bytes_read=5291712 bytes_retransmit=9 bytes_invalid=0 send_seq=23322 receive_seq=23322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997672 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101268 bytes_read=2421254 bytes_retransmit=9 bytes_invalid=0 send_seq=13725 receive_seq=13725 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33787 bytes_read=1376371 bytes_retransmit=9 bytes_invalid=0 send_seq=5572 receive_seq=5572 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34273 bytes_read=103182 bytes_retransmit=9 bytes_invalid=0 send_seq=5559 receive_seq=5559 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88365 bytes_read=2147423 bytes_retransmit=0 bytes_invalid=0 send_seq=10118 receive_seq=10118 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998669 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.8 th2: temp=60.5 th3: temp=58.2 sysload=0.11 cputime=393.112 memavail=7394652 print_time=5419.015 buffer_time=1.999 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 116 Hz
Stats 5395.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24692063 bytes_read=3823967 bytes_retransmit=9 bytes_invalid=0 send_seq=463955 receive_seq=463955 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=0 freq=400015849 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33526 bytes_read=105258 bytes_retransmit=0 bytes_invalid=0 send_seq=5559 receive_seq=5559 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997241 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169142 bytes_read=5291840 bytes_retransmit=9 bytes_invalid=0 send_seq=23323 receive_seq=23323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997655 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101344 bytes_read=2424339 bytes_retransmit=9 bytes_invalid=0 send_seq=13736 receive_seq=13736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997558 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33793 bytes_read=1376635 bytes_retransmit=9 bytes_invalid=0 send_seq=5573 receive_seq=5573 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34279 bytes_read=103198 bytes_retransmit=9 bytes_invalid=0 send_seq=5560 receive_seq=5560 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88371 bytes_read=2147779 bytes_retransmit=0 bytes_invalid=0 send_seq=10119 receive_seq=10119 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998668 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.5 th2: temp=60.4 th3: temp=58.1 sysload=0.10 cputime=393.231 memavail=7394652 print_time=5420.220 buffer_time=2.204 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 117 Hz
Stats 5396.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24695325 bytes_read=3824643 bytes_retransmit=9 bytes_invalid=0 send_seq=464025 receive_seq=464025 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015851 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33532 bytes_read=105274 bytes_retransmit=0 bytes_invalid=0 send_seq=5560 receive_seq=5560 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997235 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169148 bytes_read=5291940 bytes_retransmit=9 bytes_invalid=0 send_seq=23324 receive_seq=23324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997620 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101420 bytes_read=2427398 bytes_retransmit=9 bytes_invalid=0 send_seq=13747 receive_seq=13747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33799 bytes_read=1376899 bytes_retransmit=9 bytes_invalid=0 send_seq=5574 receive_seq=5574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34285 bytes_read=103214 bytes_retransmit=9 bytes_invalid=0 send_seq=5561 receive_seq=5561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88377 bytes_read=2148135 bytes_retransmit=0 bytes_invalid=0 send_seq=10120 receive_seq=10120 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998656 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=54.4 th1: temp=55.8 th2: temp=60.7 th3: temp=58.1 sysload=0.10 cputime=393.335 memavail=7394652 print_time=5421.088 buffer_time=2.071 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 118 Hz
Stats 5397.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24699555 bytes_read=3825363 bytes_retransmit=9 bytes_invalid=0 send_seq=464107 receive_seq=464107 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015845 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33538 bytes_read=105290 bytes_retransmit=0 bytes_invalid=0 send_seq=5561 receive_seq=5561 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997237 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169154 bytes_read=5292040 bytes_retransmit=9 bytes_invalid=0 send_seq=23325 receive_seq=23325 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997638 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101489 bytes_read=2430432 bytes_retransmit=9 bytes_invalid=0 send_seq=13757 receive_seq=13757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33805 bytes_read=1377133 bytes_retransmit=9 bytes_invalid=0 send_seq=5575 receive_seq=5575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997626 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34291 bytes_read=103241 bytes_retransmit=9 bytes_invalid=0 send_seq=5562 receive_seq=5562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88383 bytes_read=2148491 bytes_retransmit=0 bytes_invalid=0 send_seq=10121 receive_seq=10121 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998660 coil_temp=17.0 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=54.1 th1: temp=55.6 th2: temp=60.4 th3: temp=58.2 sysload=0.10 cputime=393.443 memavail=7394736 print_time=5422.019 buffer_time=2.003 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 119 Hz
Stats 5398.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24704421 bytes_read=3826187 bytes_retransmit=9 bytes_invalid=0 send_seq=464204 receive_seq=464204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=400015847 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33544 bytes_read=105306 bytes_retransmit=0 bytes_invalid=0 send_seq=5562 receive_seq=5562 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997239 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169160 bytes_read=5292168 bytes_retransmit=9 bytes_invalid=0 send_seq=23326 receive_seq=23326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997623 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101565 bytes_read=2433518 bytes_retransmit=9 bytes_invalid=0 send_seq=13768 receive_seq=13768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997495 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33811 bytes_read=1377412 bytes_retransmit=9 bytes_invalid=0 send_seq=5576 receive_seq=5576 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34297 bytes_read=103257 bytes_retransmit=9 bytes_invalid=0 send_seq=5563 receive_seq=5563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88389 bytes_read=2148847 bytes_retransmit=0 bytes_invalid=0 send_seq=10122 receive_seq=10122 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998671 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=54.4 th1: temp=55.9 th2: temp=60.7 th3: temp=58.2 sysload=0.10 cputime=393.564 memavail=7394736 print_time=5423.213 buffer_time=2.196 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 120 Hz
Stats 5399.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24707761 bytes_read=3826852 bytes_retransmit=9 bytes_invalid=0 send_seq=464275 receive_seq=464275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015865 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33550 bytes_read=105322 bytes_retransmit=0 bytes_invalid=0 send_seq=5563 receive_seq=5563 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997236 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169166 bytes_read=5292282 bytes_retransmit=9 bytes_invalid=0 send_seq=23327 receive_seq=23327 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997611 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101641 bytes_read=2436591 bytes_retransmit=9 bytes_invalid=0 send_seq=13779 receive_seq=13779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997486 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33817 bytes_read=1377676 bytes_retransmit=9 bytes_invalid=0 send_seq=5577 receive_seq=5577 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34303 bytes_read=103273 bytes_retransmit=9 bytes_invalid=0 send_seq=5564 receive_seq=5564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88395 bytes_read=2149203 bytes_retransmit=0 bytes_invalid=0 send_seq=10123 receive_seq=10123 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998686 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.7 th2: temp=60.8 th3: temp=58.2 sysload=0.10 cputime=393.672 memavail=7394736 print_time=5424.094 buffer_time=2.077 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 121 Hz
Stats 5400.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24712067 bytes_read=3827592 bytes_retransmit=9 bytes_invalid=0 send_seq=464362 receive_seq=464362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015863 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33556 bytes_read=105351 bytes_retransmit=0 bytes_invalid=0 send_seq=5564 receive_seq=5564 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997227 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169172 bytes_read=5292382 bytes_retransmit=9 bytes_invalid=0 send_seq=23328 receive_seq=23328 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997554 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101717 bytes_read=2439652 bytes_retransmit=9 bytes_invalid=0 send_seq=13790 receive_seq=13790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997438 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33823 bytes_read=1377910 bytes_retransmit=9 bytes_invalid=0 send_seq=5578 receive_seq=5578 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997613 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34309 bytes_read=103289 bytes_retransmit=9 bytes_invalid=0 send_seq=5565 receive_seq=5565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88401 bytes_read=2149559 bytes_retransmit=0 bytes_invalid=0 send_seq=10124 receive_seq=10124 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998657 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.9 th2: temp=60.5 th3: temp=58.1 sysload=0.09 cputime=393.782 memavail=7394736 print_time=5425.019 buffer_time=2.002 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 122 Hz
Stats 5401.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24717075 bytes_read=3828437 bytes_retransmit=9 bytes_invalid=0 send_seq=464460 receive_seq=464460 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015862 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33562 bytes_read=105367 bytes_retransmit=0 bytes_invalid=0 send_seq=5565 receive_seq=5565 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997223 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169178 bytes_read=5292510 bytes_retransmit=9 bytes_invalid=0 send_seq=23329 receive_seq=23329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997550 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101793 bytes_read=2442737 bytes_retransmit=9 bytes_invalid=0 send_seq=13801 receive_seq=13801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997448 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33829 bytes_read=1378174 bytes_retransmit=9 bytes_invalid=0 send_seq=5579 receive_seq=5579 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997616 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34315 bytes_read=103305 bytes_retransmit=9 bytes_invalid=0 send_seq=5566 receive_seq=5566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88407 bytes_read=2149915 bytes_retransmit=0 bytes_invalid=0 send_seq=10125 receive_seq=10125 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998657 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=54.2 th1: temp=55.8 th2: temp=60.4 th3: temp=58.0 sysload=0.09 cputime=393.907 memavail=7394736 print_time=5426.222 buffer_time=2.204 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 123 Hz
Stats 5402.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24720407 bytes_read=3829102 bytes_retransmit=9 bytes_invalid=0 send_seq=464531 receive_seq=464531 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015875 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33568 bytes_read=105383 bytes_retransmit=0 bytes_invalid=0 send_seq=5566 receive_seq=5566 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997227 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169184 bytes_read=5292610 bytes_retransmit=9 bytes_invalid=0 send_seq=23330 receive_seq=23330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997575 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101869 bytes_read=2445793 bytes_retransmit=9 bytes_invalid=0 send_seq=13812 receive_seq=13812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997485 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33835 bytes_read=1378438 bytes_retransmit=9 bytes_invalid=0 send_seq=5580 receive_seq=5580 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34321 bytes_read=103332 bytes_retransmit=9 bytes_invalid=0 send_seq=5567 receive_seq=5567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88413 bytes_read=2150271 bytes_retransmit=0 bytes_invalid=0 send_seq=10126 receive_seq=10126 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998657 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=54.5 th1: temp=55.9 th2: temp=60.5 th3: temp=58.2 sysload=0.09 cputime=394.015 memavail=7394484 print_time=5427.094 buffer_time=2.076 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 124 Hz
Stats 5403.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24724771 bytes_read=3829852 bytes_retransmit=9 bytes_invalid=0 send_seq=464619 receive_seq=464619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015872 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33574 bytes_read=105399 bytes_retransmit=0 bytes_invalid=0 send_seq=5567 receive_seq=5567 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997202 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169190 bytes_read=5292710 bytes_retransmit=9 bytes_invalid=0 send_seq=23331 receive_seq=23331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997536 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=101945 bytes_read=2448908 bytes_retransmit=9 bytes_invalid=0 send_seq=13823 receive_seq=13823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997450 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33841 bytes_read=1378687 bytes_retransmit=9 bytes_invalid=0 send_seq=5581 receive_seq=5581 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997598 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34327 bytes_read=103348 bytes_retransmit=9 bytes_invalid=0 send_seq=5568 receive_seq=5568 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88419 bytes_read=2150627 bytes_retransmit=0 bytes_invalid=0 send_seq=10127 receive_seq=10127 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998642 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.7 th2: temp=60.5 th3: temp=58.1 sysload=0.09 cputime=394.127 memavail=7394484 print_time=5428.021 buffer_time=2.003 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 125 Hz
Stats 5404.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24729792 bytes_read=3830681 bytes_retransmit=9 bytes_invalid=0 send_seq=464717 receive_seq=464717 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015865 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33580 bytes_read=105415 bytes_retransmit=0 bytes_invalid=0 send_seq=5568 receive_seq=5568 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997213 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169196 bytes_read=5292852 bytes_retransmit=9 bytes_invalid=0 send_seq=23332 receive_seq=23332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997598 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102021 bytes_read=2452010 bytes_retransmit=9 bytes_invalid=0 send_seq=13834 receive_seq=13834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997450 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33847 bytes_read=1378951 bytes_retransmit=9 bytes_invalid=0 send_seq=5582 receive_seq=5582 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997603 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34333 bytes_read=103364 bytes_retransmit=9 bytes_invalid=0 send_seq=5569 receive_seq=5569 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88425 bytes_read=2150983 bytes_retransmit=0 bytes_invalid=0 send_seq=10128 receive_seq=10128 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998671 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=54.6 th1: temp=55.9 th2: temp=60.6 th3: temp=58.1 sysload=0.09 cputime=394.246 memavail=7394484 print_time=5429.227 buffer_time=2.208 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 126 Hz
Stats 5405.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24733129 bytes_read=3831346 bytes_retransmit=9 bytes_invalid=0 send_seq=464788 receive_seq=464788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015866 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=33586 bytes_read=105444 bytes_retransmit=0 bytes_invalid=0 send_seq=5569 receive_seq=5569 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997231 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169202 bytes_read=5292952 bytes_retransmit=9 bytes_invalid=0 send_seq=23333 receive_seq=23333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997609 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102097 bytes_read=2455067 bytes_retransmit=9 bytes_invalid=0 send_seq=13845 receive_seq=13845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33853 bytes_read=1379215 bytes_retransmit=9 bytes_invalid=0 send_seq=5583 receive_seq=5583 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34339 bytes_read=103380 bytes_retransmit=9 bytes_invalid=0 send_seq=5570 receive_seq=5570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88431 bytes_read=2151339 bytes_retransmit=0 bytes_invalid=0 send_seq=10129 receive_seq=10129 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998675 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=54.4 th1: temp=55.7 th2: temp=60.5 th3: temp=58.1 sysload=0.08 cputime=394.350 memavail=7394484 print_time=5430.096 buffer_time=2.078 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 127 Hz
Stats 5406.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24737517 bytes_read=3832117 bytes_retransmit=9 bytes_invalid=0 send_seq=464877 receive_seq=464877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015862 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=33592 bytes_read=105460 bytes_retransmit=0 bytes_invalid=0 send_seq=5570 receive_seq=5570 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997238 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169208 bytes_read=5293052 bytes_retransmit=9 bytes_invalid=0 send_seq=23334 receive_seq=23334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997591 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102173 bytes_read=2458126 bytes_retransmit=9 bytes_invalid=0 send_seq=13856 receive_seq=13856 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997470 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33859 bytes_read=1379449 bytes_retransmit=9 bytes_invalid=0 send_seq=5584 receive_seq=5584 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997621 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34345 bytes_read=103396 bytes_retransmit=9 bytes_invalid=0 send_seq=5571 receive_seq=5571 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88437 bytes_read=2151695 bytes_retransmit=0 bytes_invalid=0 send_seq=10130 receive_seq=10130 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998661 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=54.2 th1: temp=55.9 th2: temp=60.6 th3: temp=58.1 sysload=0.08 cputime=394.459 memavail=7394536 print_time=5431.026 buffer_time=2.007 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 128 Hz
Stats 5407.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24742478 bytes_read=3832941 bytes_retransmit=9 bytes_invalid=0 send_seq=464974 receive_seq=464974 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=72 freq=400015863 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=33598 bytes_read=105476 bytes_retransmit=0 bytes_invalid=0 send_seq=5571 receive_seq=5571 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997243 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169214 bytes_read=5293180 bytes_retransmit=9 bytes_invalid=0 send_seq=23335 receive_seq=23335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997592 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102249 bytes_read=2461210 bytes_retransmit=9 bytes_invalid=0 send_seq=13867 receive_seq=13867 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997488 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33865 bytes_read=1379728 bytes_retransmit=9 bytes_invalid=0 send_seq=5585 receive_seq=5585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34351 bytes_read=103423 bytes_retransmit=9 bytes_invalid=0 send_seq=5572 receive_seq=5572 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88443 bytes_read=2152051 bytes_retransmit=0 bytes_invalid=0 send_seq=10131 receive_seq=10131 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998719 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.7 th2: temp=60.6 th3: temp=58.0 sysload=0.08 cputime=394.583 memavail=7394536 print_time=5432.228 buffer_time=2.208 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 129 Hz
Stats 5408.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24745993 bytes_read=3833596 bytes_retransmit=9 bytes_invalid=0 send_seq=465043 receive_seq=465043 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015881 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=33604 bytes_read=105492 bytes_retransmit=0 bytes_invalid=0 send_seq=5572 receive_seq=5572 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997257 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169220 bytes_read=5293280 bytes_retransmit=9 bytes_invalid=0 send_seq=23336 receive_seq=23336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997631 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102318 bytes_read=2464245 bytes_retransmit=9 bytes_invalid=0 send_seq=13877 receive_seq=13877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997486 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33871 bytes_read=1379992 bytes_retransmit=9 bytes_invalid=0 send_seq=5586 receive_seq=5586 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34357 bytes_read=103439 bytes_retransmit=9 bytes_invalid=0 send_seq=5573 receive_seq=5573 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88449 bytes_read=2152407 bytes_retransmit=0 bytes_invalid=0 send_seq=10132 receive_seq=10132 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998703 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.9 th2: temp=60.5 th3: temp=58.1 sysload=0.08 cputime=394.688 memavail=7394536 print_time=5433.104 buffer_time=2.083 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 130 Hz
Stats 5409.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24750423 bytes_read=3834346 bytes_retransmit=9 bytes_invalid=0 send_seq=465131 receive_seq=465131 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015873 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=33610 bytes_read=105508 bytes_retransmit=0 bytes_invalid=0 send_seq=5573 receive_seq=5573 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997232 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169226 bytes_read=5293394 bytes_retransmit=9 bytes_invalid=0 send_seq=23337 receive_seq=23337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997592 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102394 bytes_read=2467319 bytes_retransmit=9 bytes_invalid=0 send_seq=13888 receive_seq=13888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997444 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33877 bytes_read=1380226 bytes_retransmit=9 bytes_invalid=0 send_seq=5587 receive_seq=5587 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997612 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34363 bytes_read=103455 bytes_retransmit=9 bytes_invalid=0 send_seq=5574 receive_seq=5574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88455 bytes_read=2152763 bytes_retransmit=0 bytes_invalid=0 send_seq=10133 receive_seq=10133 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998722 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=54.4 th1: temp=55.8 th2: temp=60.8 th3: temp=58.1 sysload=0.08 cputime=394.810 memavail=7395132 print_time=5434.030 buffer_time=2.009 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 131 Hz
Stats 5410.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24755393 bytes_read=3835173 bytes_retransmit=9 bytes_invalid=0 send_seq=465229 receive_seq=465229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=144 freq=400015870 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33616 bytes_read=105537 bytes_retransmit=0 bytes_invalid=0 send_seq=5574 receive_seq=5574 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997293 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169232 bytes_read=5293522 bytes_retransmit=9 bytes_invalid=0 send_seq=23338 receive_seq=23338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997675 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102470 bytes_read=2470465 bytes_retransmit=9 bytes_invalid=0 send_seq=13899 receive_seq=13899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997463 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33883 bytes_read=1380505 bytes_retransmit=9 bytes_invalid=0 send_seq=5588 receive_seq=5588 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34369 bytes_read=103471 bytes_retransmit=9 bytes_invalid=0 send_seq=5575 receive_seq=5575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88461 bytes_read=2153119 bytes_retransmit=0 bytes_invalid=0 send_seq=10134 receive_seq=10134 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998713 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.7 th2: temp=60.2 th3: temp=58.1 sysload=0.08 cputime=394.931 memavail=7395132 print_time=5435.230 buffer_time=2.209 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 132 Hz
Stats 5411.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24758973 bytes_read=3835861 bytes_retransmit=9 bytes_invalid=0 send_seq=465302 receive_seq=465302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015867 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33622 bytes_read=105553 bytes_retransmit=0 bytes_invalid=0 send_seq=5575 receive_seq=5575 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997289 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169238 bytes_read=5293622 bytes_retransmit=9 bytes_invalid=0 send_seq=23339 receive_seq=23339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997741 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102546 bytes_read=2473522 bytes_retransmit=9 bytes_invalid=0 send_seq=13910 receive_seq=13910 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997475 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33889 bytes_read=1380754 bytes_retransmit=9 bytes_invalid=0 send_seq=5589 receive_seq=5589 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997634 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34375 bytes_read=103487 bytes_retransmit=9 bytes_invalid=0 send_seq=5576 receive_seq=5576 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88467 bytes_read=2153475 bytes_retransmit=0 bytes_invalid=0 send_seq=10135 receive_seq=10135 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998699 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.9 th2: temp=60.4 th3: temp=58.2 sysload=0.08 cputime=395.038 memavail=7394908 print_time=5436.098 buffer_time=2.077 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Stats 5412.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24761383 bytes_read=3836456 bytes_retransmit=9 bytes_invalid=0 send_seq=465359 receive_seq=465359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015875 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33628 bytes_read=105569 bytes_retransmit=0 bytes_invalid=0 send_seq=5576 receive_seq=5576 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997282 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169244 bytes_read=5293718 bytes_retransmit=9 bytes_invalid=0 send_seq=23340 receive_seq=23340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997776 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102622 bytes_read=2476574 bytes_retransmit=9 bytes_invalid=0 send_seq=13921 receive_seq=13921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997489 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=33895 bytes_read=1380988 bytes_retransmit=9 bytes_invalid=0 send_seq=5590 receive_seq=5590 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34381 bytes_read=103513 bytes_retransmit=9 bytes_invalid=0 send_seq=5577 receive_seq=5577 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88473 bytes_read=2153831 bytes_retransmit=0 bytes_invalid=0 send_seq=10136 receive_seq=10136 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998685 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=54.7 th1: temp=55.6 th2: temp=60.5 th3: temp=58.3 sysload=0.08 cputime=395.121 memavail=7394908 print_time=5436.480 buffer_time=1.459 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5413.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24761681 bytes_read=3836910 bytes_retransmit=9 bytes_invalid=0 send_seq=465382 receive_seq=465382 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015875 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33634 bytes_read=105585 bytes_retransmit=0 bytes_invalid=0 send_seq=5577 receive_seq=5577 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997261 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169250 bytes_read=5293837 bytes_retransmit=9 bytes_invalid=0 send_seq=23341 receive_seq=23341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997734 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102698 bytes_read=2479639 bytes_retransmit=9 bytes_invalid=0 send_seq=13932 receive_seq=13932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997459 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33901 bytes_read=1381282 bytes_retransmit=9 bytes_invalid=0 send_seq=5591 receive_seq=5591 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997618 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34387 bytes_read=103528 bytes_retransmit=9 bytes_invalid=0 send_seq=5578 receive_seq=5578 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88479 bytes_read=2154187 bytes_retransmit=0 bytes_invalid=0 send_seq=10137 receive_seq=10137 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998660 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.8 th2: temp=60.8 th3: temp=58.2 sysload=0.08 cputime=395.183 memavail=7394908 print_time=5436.480 buffer_time=0.457 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
LIS2DW finished 'toolboard_t1' measurements
Resonances data written to /tmp/resonances_x_250.000_250.000_20.000_t1.csv file
Probing point (250.000, 250.000, 20.000)
Stats 5414.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24762033 bytes_read=3837340 bytes_retransmit=9 bytes_invalid=0 send_seq=465406 receive_seq=465406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015875 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=33640 bytes_read=105601 bytes_retransmit=0 bytes_invalid=0 send_seq=5578 receive_seq=5578 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997253 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169256 bytes_read=5293944 bytes_retransmit=9 bytes_invalid=0 send_seq=23342 receive_seq=23342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997708 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102794 bytes_read=2481436 bytes_retransmit=9 bytes_invalid=0 send_seq=13944 receive_seq=13944 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997450 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33907 bytes_read=1381531 bytes_retransmit=9 bytes_invalid=0 send_seq=5592 receive_seq=5592 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34393 bytes_read=103543 bytes_retransmit=9 bytes_invalid=0 send_seq=5579 receive_seq=5579 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88485 bytes_read=2154543 bytes_retransmit=0 bytes_invalid=0 send_seq=10138 receive_seq=10138 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998652 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=54.4 th1: temp=55.7 th2: temp=60.9 th3: temp=58.1 sysload=0.08 cputime=395.299 memavail=7396568 print_time=5437.453 buffer_time=0.430 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t1' measurements
toolhead: max_velocity: 600.000000
max_accel: 8379.841000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance testing
Testing frequency 10 Hz
Testing frequency 11 Hz
Testing frequency 12 Hz
Stats 5415.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24771252 bytes_read=3838500 bytes_retransmit=9 bytes_invalid=0 send_seq=465576 receive_seq=465576 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=395 freq=400015868 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33646 bytes_read=105630 bytes_retransmit=0 bytes_invalid=0 send_seq=5579 receive_seq=5579 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997263 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169262 bytes_read=5294037 bytes_retransmit=9 bytes_invalid=0 send_seq=23343 receive_seq=23343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997678 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=102942 bytes_read=2483181 bytes_retransmit=9 bytes_invalid=0 send_seq=13961 receive_seq=13961 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997444 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33913 bytes_read=1381765 bytes_retransmit=9 bytes_invalid=0 send_seq=5593 receive_seq=5593 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34399 bytes_read=103558 bytes_retransmit=9 bytes_invalid=0 send_seq=5580 receive_seq=5580 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88491 bytes_read=2154899 bytes_retransmit=0 bytes_invalid=0 send_seq=10139 receive_seq=10139 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998661 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=54.5 th1: temp=55.9 th2: temp=60.6 th3: temp=58.0 sysload=0.15 cputime=395.493 memavail=7396568 print_time=5440.616 buffer_time=2.593 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5416.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24774377 bytes_read=3839194 bytes_retransmit=9 bytes_invalid=0 send_seq=465644 receive_seq=465644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=136 freq=400015882 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33652 bytes_read=105646 bytes_retransmit=0 bytes_invalid=0 send_seq=5580 receive_seq=5580 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997281 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169268 bytes_read=5294160 bytes_retransmit=9 bytes_invalid=0 send_seq=23344 receive_seq=23344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997671 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103018 bytes_read=2486253 bytes_retransmit=9 bytes_invalid=0 send_seq=13972 receive_seq=13972 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997507 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33919 bytes_read=1382044 bytes_retransmit=9 bytes_invalid=0 send_seq=5594 receive_seq=5594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34405 bytes_read=103573 bytes_retransmit=9 bytes_invalid=0 send_seq=5581 receive_seq=5581 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88497 bytes_read=2155255 bytes_retransmit=0 bytes_invalid=0 send_seq=10140 receive_seq=10140 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998666 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.8 th2: temp=60.7 th3: temp=58.1 sysload=0.15 cputime=395.573 memavail=7396568 print_time=5441.210 buffer_time=2.186 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 13 Hz
Stats 5417.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24778038 bytes_read=3839869 bytes_retransmit=9 bytes_invalid=0 send_seq=465717 receive_seq=465717 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015890 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33658 bytes_read=105662 bytes_retransmit=0 bytes_invalid=0 send_seq=5581 receive_seq=5581 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997250 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169274 bytes_read=5294260 bytes_retransmit=9 bytes_invalid=0 send_seq=23345 receive_seq=23345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997625 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103094 bytes_read=2489281 bytes_retransmit=9 bytes_invalid=0 send_seq=13983 receive_seq=13983 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997481 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33925 bytes_read=1382293 bytes_retransmit=9 bytes_invalid=0 send_seq=5595 receive_seq=5595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997634 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34411 bytes_read=103599 bytes_retransmit=9 bytes_invalid=0 send_seq=5582 receive_seq=5582 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88503 bytes_read=2155611 bytes_retransmit=0 bytes_invalid=0 send_seq=10141 receive_seq=10141 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998662 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=54.5 th1: temp=55.7 th2: temp=60.4 th3: temp=58.1 sysload=0.15 cputime=395.659 memavail=7395336 print_time=5442.053 buffer_time=2.029 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 14 Hz
Stats 5418.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24782661 bytes_read=3840624 bytes_retransmit=9 bytes_invalid=0 send_seq=465806 receive_seq=465806 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=488 freq=400015904 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33664 bytes_read=105678 bytes_retransmit=0 bytes_invalid=0 send_seq=5582 receive_seq=5582 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997225 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169280 bytes_read=5294360 bytes_retransmit=9 bytes_invalid=0 send_seq=23346 receive_seq=23346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997608 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103170 bytes_read=2492338 bytes_retransmit=9 bytes_invalid=0 send_seq=13994 receive_seq=13994 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997460 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33931 bytes_read=1382542 bytes_retransmit=9 bytes_invalid=0 send_seq=5596 receive_seq=5596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34417 bytes_read=103614 bytes_retransmit=9 bytes_invalid=0 send_seq=5583 receive_seq=5583 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88509 bytes_read=2155967 bytes_retransmit=0 bytes_invalid=0 send_seq=10142 receive_seq=10142 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998659 coil_temp=16.9 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=54.7 th1: temp=55.4 th2: temp=60.4 th3: temp=58.1 sysload=0.15 cputime=395.751 memavail=7395336 print_time=5443.051 buffer_time=2.026 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 15 Hz
Testing frequency 16 Hz
Stats 5419.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24787558 bytes_read=3841423 bytes_retransmit=9 bytes_invalid=0 send_seq=465898 receive_seq=465898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=1740 freq=400015909 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33670 bytes_read=105694 bytes_retransmit=0 bytes_invalid=0 send_seq=5583 receive_seq=5583 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997228 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169286 bytes_read=5294502 bytes_retransmit=9 bytes_invalid=0 send_seq=23347 receive_seq=23347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997573 toolboard_t1: mcu_awake=0.261 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=103246 bytes_read=2495441 bytes_retransmit=9 bytes_invalid=0 send_seq=14005 receive_seq=14005 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997435 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33937 bytes_read=1382821 bytes_retransmit=9 bytes_invalid=0 send_seq=5597 receive_seq=5597 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34423 bytes_read=103629 bytes_retransmit=9 bytes_invalid=0 send_seq=5584 receive_seq=5584 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88515 bytes_read=2156323 bytes_retransmit=0 bytes_invalid=0 send_seq=10143 receive_seq=10143 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998636 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=54.5 th1: temp=55.5 th2: temp=60.4 th3: temp=58.1 sysload=0.15 cputime=395.851 memavail=7395336 print_time=5444.301 buffer_time=2.276 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5420.4: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=24792776 bytes_read=3842228 bytes_retransmit=9 bytes_invalid=0 send_seq=465997 receive_seq=465997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=760 freq=400015906 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33676 bytes_read=105722 bytes_retransmit=0 bytes_invalid=0 send_seq=5584 receive_seq=5584 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997220 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169292 bytes_read=5294602 bytes_retransmit=9 bytes_invalid=0 send_seq=23348 receive_seq=23348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997573 toolboard_t1: mcu_awake=0.261 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=103322 bytes_read=2498497 bytes_retransmit=9 bytes_invalid=0 send_seq=14016 receive_seq=14016 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997439 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33943 bytes_read=1383070 bytes_retransmit=9 bytes_invalid=0 send_seq=5598 receive_seq=5598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34429 bytes_read=103644 bytes_retransmit=9 bytes_invalid=0 send_seq=5585 receive_seq=5585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88521 bytes_read=2156679 bytes_retransmit=0 bytes_invalid=0 send_seq=10144 receive_seq=10144 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998631 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=54.4 th1: temp=55.3 th2: temp=60.2 th3: temp=58.0 sysload=0.30 cputime=395.942 memavail=7395336 print_time=5445.182 buffer_time=2.156 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 17 Hz
Stats 5421.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=24797234 bytes_read=3842965 bytes_retransmit=9 bytes_invalid=0 send_seq=466080 receive_seq=466080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=1712 freq=400015901 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33682 bytes_read=105737 bytes_retransmit=0 bytes_invalid=0 send_seq=5585 receive_seq=5585 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997225 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169298 bytes_read=5294702 bytes_retransmit=9 bytes_invalid=0 send_seq=23349 receive_seq=23349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997569 toolboard_t1: mcu_awake=0.261 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=103391 bytes_read=2501532 bytes_retransmit=9 bytes_invalid=0 send_seq=14026 receive_seq=14026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997451 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33949 bytes_read=1383304 bytes_retransmit=9 bytes_invalid=0 send_seq=5599 receive_seq=5599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34435 bytes_read=103659 bytes_retransmit=9 bytes_invalid=0 send_seq=5586 receive_seq=5586 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88527 bytes_read=2157035 bytes_retransmit=0 bytes_invalid=0 send_seq=10145 receive_seq=10145 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998635 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.3 th2: temp=60.4 th3: temp=57.9 sysload=0.30 cputime=396.034 memavail=7395112 print_time=5446.104 buffer_time=2.077 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 18 Hz
Stats 5422.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=24802680 bytes_read=3843796 bytes_retransmit=9 bytes_invalid=0 send_seq=466179 receive_seq=466179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=1032 freq=400015928 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33688 bytes_read=105752 bytes_retransmit=0 bytes_invalid=0 send_seq=5586 receive_seq=5586 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997242 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169304 bytes_read=5294830 bytes_retransmit=9 bytes_invalid=0 send_seq=23350 receive_seq=23350 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997600 toolboard_t1: mcu_awake=0.261 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=103467 bytes_read=2504618 bytes_retransmit=9 bytes_invalid=0 send_seq=14037 receive_seq=14037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997470 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33955 bytes_read=1383583 bytes_retransmit=9 bytes_invalid=0 send_seq=5600 receive_seq=5600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34441 bytes_read=103685 bytes_retransmit=9 bytes_invalid=0 send_seq=5587 receive_seq=5587 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88533 bytes_read=2157391 bytes_retransmit=0 bytes_invalid=0 send_seq=10146 receive_seq=10146 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998661 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=54.7 th1: temp=55.1 th2: temp=59.8 th3: temp=58.0 sysload=0.30 cputime=396.134 memavail=7395136 print_time=5447.067 buffer_time=2.040 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 19 Hz
Testing frequency 20 Hz
Stats 5423.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=24808392 bytes_read=3844636 bytes_retransmit=9 bytes_invalid=0 send_seq=466285 receive_seq=466285 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=2247 freq=400016016 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33694 bytes_read=105767 bytes_retransmit=0 bytes_invalid=0 send_seq=5587 receive_seq=5587 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997201 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169310 bytes_read=5294930 bytes_retransmit=9 bytes_invalid=0 send_seq=23351 receive_seq=23351 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997543 toolboard_t1: mcu_awake=0.261 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=103543 bytes_read=2507675 bytes_retransmit=9 bytes_invalid=0 send_seq=14048 receive_seq=14048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997421 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33961 bytes_read=1383847 bytes_retransmit=9 bytes_invalid=0 send_seq=5601 receive_seq=5601 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997598 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34447 bytes_read=103700 bytes_retransmit=9 bytes_invalid=0 send_seq=5588 receive_seq=5588 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88539 bytes_read=2157747 bytes_retransmit=0 bytes_invalid=0 send_seq=10147 receive_seq=10147 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998624 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.4 th2: temp=60.3 th3: temp=57.8 sysload=0.30 cputime=396.240 memavail=7395136 print_time=5448.257 buffer_time=2.229 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5424.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=24813414 bytes_read=3845416 bytes_retransmit=9 bytes_invalid=0 send_seq=466379 receive_seq=466379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=3068 freq=400016031 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33700 bytes_read=105782 bytes_retransmit=0 bytes_invalid=0 send_seq=5588 receive_seq=5588 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997079 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169316 bytes_read=5295044 bytes_retransmit=9 bytes_invalid=0 send_seq=23352 receive_seq=23352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997393 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103619 bytes_read=2510806 bytes_retransmit=9 bytes_invalid=0 send_seq=14059 receive_seq=14059 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997284 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33967 bytes_read=1384081 bytes_retransmit=9 bytes_invalid=0 send_seq=5602 receive_seq=5602 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997491 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34453 bytes_read=103715 bytes_retransmit=9 bytes_invalid=0 send_seq=5589 receive_seq=5589 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999401 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88545 bytes_read=2158103 bytes_retransmit=0 bytes_invalid=0 send_seq=10148 receive_seq=10148 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998537 coil_temp=17.0 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=54.3 th1: temp=54.9 th2: temp=60.1 th3: temp=57.6 sysload=0.30 cputime=396.333 memavail=7395140 print_time=5449.128 buffer_time=2.100 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 21 Hz
Stats 5425.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=24819630 bytes_read=3846330 bytes_retransmit=9 bytes_invalid=0 send_seq=466494 receive_seq=466494 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=2044 freq=400016028 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33706 bytes_read=105810 bytes_retransmit=0 bytes_invalid=0 send_seq=5589 receive_seq=5589 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997073 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169322 bytes_read=5295172 bytes_retransmit=9 bytes_invalid=0 send_seq=23353 receive_seq=23353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997397 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103695 bytes_read=2513890 bytes_retransmit=9 bytes_invalid=0 send_seq=14070 receive_seq=14070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997286 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33973 bytes_read=1384360 bytes_retransmit=9 bytes_invalid=0 send_seq=5603 receive_seq=5603 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997499 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34459 bytes_read=103730 bytes_retransmit=9 bytes_invalid=0 send_seq=5590 receive_seq=5590 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999405 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88551 bytes_read=2158459 bytes_retransmit=0 bytes_invalid=0 send_seq=10149 receive_seq=10149 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998532 coil_temp=17.0 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=54.4 th1: temp=54.9 th2: temp=60.1 th3: temp=57.7 sysload=0.44 cputime=396.432 memavail=7395140 print_time=5450.078 buffer_time=2.049 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 22 Hz
Testing frequency 23 Hz
Stats 5426.4: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=24825971 bytes_read=3847236 bytes_retransmit=9 bytes_invalid=0 send_seq=466610 receive_seq=466610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=3164 freq=400016038 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33712 bytes_read=105826 bytes_retransmit=0 bytes_invalid=0 send_seq=5590 receive_seq=5590 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997091 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169328 bytes_read=5295272 bytes_retransmit=9 bytes_invalid=0 send_seq=23354 receive_seq=23354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997440 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103771 bytes_read=2516946 bytes_retransmit=9 bytes_invalid=0 send_seq=14081 receive_seq=14081 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997319 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33979 bytes_read=1384609 bytes_retransmit=9 bytes_invalid=0 send_seq=5604 receive_seq=5604 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997527 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34465 bytes_read=103745 bytes_retransmit=9 bytes_invalid=0 send_seq=5591 receive_seq=5591 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999409 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88557 bytes_read=2158815 bytes_retransmit=0 bytes_invalid=0 send_seq=10150 receive_seq=10150 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998541 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=54.5 th1: temp=54.9 th2: temp=60.0 th3: temp=57.6 sysload=0.44 cputime=396.546 memavail=7391804 print_time=5451.272 buffer_time=2.243 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5427.4: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=24831331 bytes_read=3848051 bytes_retransmit=9 bytes_invalid=0 send_seq=466711 receive_seq=466711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=4156 freq=400016043 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33718 bytes_read=105842 bytes_retransmit=0 bytes_invalid=0 send_seq=5591 receive_seq=5591 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997132 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169334 bytes_read=5295372 bytes_retransmit=9 bytes_invalid=0 send_seq=23355 receive_seq=23355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997465 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103847 bytes_read=2520006 bytes_retransmit=9 bytes_invalid=0 send_seq=14092 receive_seq=14092 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997347 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=33985 bytes_read=1384843 bytes_retransmit=9 bytes_invalid=0 send_seq=5605 receive_seq=5605 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997535 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34471 bytes_read=103771 bytes_retransmit=9 bytes_invalid=0 send_seq=5592 receive_seq=5592 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999411 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88563 bytes_read=2159171 bytes_retransmit=0 bytes_invalid=0 send_seq=10151 receive_seq=10151 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998563 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=54.6 th1: temp=54.7 th2: temp=60.0 th3: temp=57.6 sysload=0.44 cputime=396.641 memavail=7395296 print_time=5452.157 buffer_time=2.127 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 24 Hz
Stats 5428.4: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=24838024 bytes_read=3849000 bytes_retransmit=9 bytes_invalid=0 send_seq=466833 receive_seq=466833 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=3364 freq=400016047 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33724 bytes_read=105858 bytes_retransmit=0 bytes_invalid=0 send_seq=5592 receive_seq=5592 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997191 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169340 bytes_read=5295500 bytes_retransmit=9 bytes_invalid=0 send_seq=23356 receive_seq=23356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997456 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103923 bytes_read=2523091 bytes_retransmit=9 bytes_invalid=0 send_seq=14103 receive_seq=14103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997349 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33991 bytes_read=1385152 bytes_retransmit=9 bytes_invalid=0 send_seq=5606 receive_seq=5606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997542 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34477 bytes_read=103786 bytes_retransmit=9 bytes_invalid=0 send_seq=5593 receive_seq=5593 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999410 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88569 bytes_read=2159527 bytes_retransmit=0 bytes_invalid=0 send_seq=10152 receive_seq=10152 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998560 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=54.8 th1: temp=54.8 th2: temp=59.9 th3: temp=57.6 sysload=0.44 cputime=396.741 memavail=7395296 print_time=5453.122 buffer_time=2.091 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 25 Hz
Testing frequency 26 Hz
Stats 5429.4: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=24844879 bytes_read=3849930 bytes_retransmit=9 bytes_invalid=0 send_seq=466957 receive_seq=466957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=4888 freq=400016049 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33730 bytes_read=105874 bytes_retransmit=0 bytes_invalid=0 send_seq=5593 receive_seq=5593 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997214 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169346 bytes_read=5295600 bytes_retransmit=9 bytes_invalid=0 send_seq=23357 receive_seq=23357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997469 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=103999 bytes_read=2526165 bytes_retransmit=9 bytes_invalid=0 send_seq=14114 receive_seq=14114 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997377 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=33997 bytes_read=1385386 bytes_retransmit=9 bytes_invalid=0 send_seq=5607 receive_seq=5607 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997551 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34483 bytes_read=103801 bytes_retransmit=9 bytes_invalid=0 send_seq=5594 receive_seq=5594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999413 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88575 bytes_read=2159883 bytes_retransmit=0 bytes_invalid=0 send_seq=10153 receive_seq=10153 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998566 coil_temp=17.0 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=54.4 th1: temp=54.7 th2: temp=59.9 th3: temp=57.6 sysload=0.44 cputime=396.850 memavail=7395296 print_time=5454.349 buffer_time=2.317 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5430.4: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=24850738 bytes_read=3850785 bytes_retransmit=9 bytes_invalid=0 send_seq=467066 receive_seq=467066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=5151 freq=400016034 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33736 bytes_read=105903 bytes_retransmit=0 bytes_invalid=0 send_seq=5594 receive_seq=5594 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997216 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169352 bytes_read=5295714 bytes_retransmit=9 bytes_invalid=0 send_seq=23358 receive_seq=23358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997506 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104075 bytes_read=2529222 bytes_retransmit=9 bytes_invalid=0 send_seq=14125 receive_seq=14125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997413 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34003 bytes_read=1385620 bytes_retransmit=9 bytes_invalid=0 send_seq=5608 receive_seq=5608 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997567 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34489 bytes_read=103816 bytes_retransmit=9 bytes_invalid=0 send_seq=5595 receive_seq=5595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999418 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88581 bytes_read=2160239 bytes_retransmit=0 bytes_invalid=0 send_seq=10154 receive_seq=10154 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998580 coil_temp=17.0 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=54.6 th1: temp=54.7 th2: temp=59.8 th3: temp=57.4 sysload=0.56 cputime=396.946 memavail=7395048 print_time=5455.207 buffer_time=2.175 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 27 Hz
Stats 5431.4: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24857910 bytes_read=3851800 bytes_retransmit=9 bytes_invalid=0 send_seq=467198 receive_seq=467198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=4848 freq=400016020 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33742 bytes_read=105919 bytes_retransmit=0 bytes_invalid=0 send_seq=5595 receive_seq=5595 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997238 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169358 bytes_read=5295842 bytes_retransmit=9 bytes_invalid=0 send_seq=23359 receive_seq=23359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997539 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104151 bytes_read=2532364 bytes_retransmit=9 bytes_invalid=0 send_seq=14136 receive_seq=14136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997444 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34009 bytes_read=1385914 bytes_retransmit=9 bytes_invalid=0 send_seq=5609 receive_seq=5609 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997592 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34495 bytes_read=103831 bytes_retransmit=9 bytes_invalid=0 send_seq=5596 receive_seq=5596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88587 bytes_read=2160595 bytes_retransmit=0 bytes_invalid=0 send_seq=10155 receive_seq=10155 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998638 coil_temp=17.0 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=54.7 th1: temp=54.7 th2: temp=59.8 th3: temp=57.5 sysload=0.56 cputime=397.047 memavail=7395048 print_time=5456.183 buffer_time=2.150 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 28 Hz
Stats 5432.4: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24865252 bytes_read=3852781 bytes_retransmit=9 bytes_invalid=0 send_seq=467333 receive_seq=467333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=3619 freq=400016016 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33748 bytes_read=105935 bytes_retransmit=0 bytes_invalid=0 send_seq=5596 receive_seq=5596 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997277 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169364 bytes_read=5295942 bytes_retransmit=9 bytes_invalid=0 send_seq=23360 receive_seq=23360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997588 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104227 bytes_read=2535421 bytes_retransmit=9 bytes_invalid=0 send_seq=14147 receive_seq=14147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34015 bytes_read=1386148 bytes_retransmit=9 bytes_invalid=0 send_seq=5610 receive_seq=5610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997611 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34501 bytes_read=103857 bytes_retransmit=9 bytes_invalid=0 send_seq=5597 receive_seq=5597 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88593 bytes_read=2160951 bytes_retransmit=0 bytes_invalid=0 send_seq=10156 receive_seq=10156 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998640 coil_temp=17.0 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=54.5 th1: temp=54.5 th2: temp=59.7 th3: temp=57.4 sysload=0.56 cputime=397.146 memavail=7395048 print_time=5457.047 buffer_time=2.014 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 29 Hz
Testing frequency 30 Hz
Stats 5433.4: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24871382 bytes_read=3853660 bytes_retransmit=9 bytes_invalid=0 send_seq=467447 receive_seq=467447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=5829 freq=400016016 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33754 bytes_read=105951 bytes_retransmit=0 bytes_invalid=0 send_seq=5597 receive_seq=5597 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997297 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169370 bytes_read=5296042 bytes_retransmit=9 bytes_invalid=0 send_seq=23361 receive_seq=23361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997598 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104303 bytes_read=2538477 bytes_retransmit=9 bytes_invalid=0 send_seq=14158 receive_seq=14158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997479 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34021 bytes_read=1386397 bytes_retransmit=9 bytes_invalid=0 send_seq=5611 receive_seq=5611 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997616 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34507 bytes_read=103872 bytes_retransmit=9 bytes_invalid=0 send_seq=5598 receive_seq=5598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88599 bytes_read=2161307 bytes_retransmit=0 bytes_invalid=0 send_seq=10157 receive_seq=10157 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998635 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=54.6 th1: temp=54.7 th2: temp=59.4 th3: temp=57.3 sysload=0.56 cputime=397.253 memavail=7395048 print_time=5458.239 buffer_time=2.205 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5434.4: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24878791 bytes_read=3854664 bytes_retransmit=9 bytes_invalid=0 send_seq=467580 receive_seq=467580 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=5879 freq=400016014 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33760 bytes_read=105967 bytes_retransmit=0 bytes_invalid=0 send_seq=5598 receive_seq=5598 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997279 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169376 bytes_read=5296170 bytes_retransmit=9 bytes_invalid=0 send_seq=23362 receive_seq=23362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997611 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104379 bytes_read=2541579 bytes_retransmit=9 bytes_invalid=0 send_seq=14169 receive_seq=14169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997477 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34027 bytes_read=1386678 bytes_retransmit=9 bytes_invalid=0 send_seq=5612 receive_seq=5612 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997623 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34513 bytes_read=103887 bytes_retransmit=9 bytes_invalid=0 send_seq=5599 receive_seq=5599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88605 bytes_read=2161663 bytes_retransmit=0 bytes_invalid=0 send_seq=10158 receive_seq=10158 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998639 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=54.6 th1: temp=54.4 th2: temp=59.6 th3: temp=57.2 sysload=0.56 cputime=397.357 memavail=7395048 print_time=5459.199 buffer_time=2.165 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 31 Hz
Stats 5435.4: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24886563 bytes_read=3855649 bytes_retransmit=9 bytes_invalid=0 send_seq=467715 receive_seq=467715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=4368 freq=400016003 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33766 bytes_read=105983 bytes_retransmit=0 bytes_invalid=0 send_seq=5599 receive_seq=5599 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997272 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169382 bytes_read=5296284 bytes_retransmit=9 bytes_invalid=0 send_seq=23363 receive_seq=23363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997606 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104448 bytes_read=2544613 bytes_retransmit=9 bytes_invalid=0 send_seq=14179 receive_seq=14179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997475 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34033 bytes_read=1386896 bytes_retransmit=9 bytes_invalid=0 send_seq=5613 receive_seq=5613 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34519 bytes_read=103903 bytes_retransmit=9 bytes_invalid=0 send_seq=5600 receive_seq=5600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88611 bytes_read=2162003 bytes_retransmit=0 bytes_invalid=0 send_seq=10159 receive_seq=10159 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998639 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=54.7 th1: temp=54.7 th2: temp=59.5 th3: temp=57.3 sysload=0.52 cputime=397.458 memavail=7394796 print_time=5460.068 buffer_time=2.034 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 32 Hz
Testing frequency 33 Hz
Stats 5436.4: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=24893064 bytes_read=3856591 bytes_retransmit=9 bytes_invalid=0 send_seq=467836 receive_seq=467836 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=6772 freq=400016046 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=33778 bytes_read=106028 bytes_retransmit=0 bytes_invalid=0 send_seq=5601 receive_seq=5601 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999275 adj=49997280 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169394 bytes_read=5296400 bytes_retransmit=9 bytes_invalid=0 send_seq=23365 receive_seq=23365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997629 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104530 bytes_read=2547686 bytes_retransmit=9 bytes_invalid=0 send_seq=14191 receive_seq=14191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34045 bytes_read=1387129 bytes_retransmit=9 bytes_invalid=0 send_seq=5615 receive_seq=5615 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34531 bytes_read=103935 bytes_retransmit=9 bytes_invalid=0 send_seq=5602 receive_seq=5602 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88623 bytes_read=2162375 bytes_retransmit=0 bytes_invalid=0 send_seq=10161 receive_seq=10161 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998714 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=54.6 th1: temp=54.3 th2: temp=59.6 th3: temp=57.4 sysload=0.52 cputime=397.570 memavail=7394796 print_time=5461.279 buffer_time=2.244 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5437.4: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=24900890 bytes_read=3857625 bytes_retransmit=9 bytes_invalid=0 send_seq=467975 receive_seq=467975 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=6904 freq=400016036 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=33784 bytes_read=106044 bytes_retransmit=0 bytes_invalid=0 send_seq=5602 receive_seq=5602 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999273 adj=49997499 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169400 bytes_read=5296528 bytes_retransmit=9 bytes_invalid=0 send_seq=23366 receive_seq=23366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997570 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104606 bytes_read=2550771 bytes_retransmit=9 bytes_invalid=0 send_seq=14202 receive_seq=14202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997423 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34051 bytes_read=1387403 bytes_retransmit=9 bytes_invalid=0 send_seq=5616 receive_seq=5616 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997576 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34537 bytes_read=103962 bytes_retransmit=9 bytes_invalid=0 send_seq=5603 receive_seq=5603 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999422 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88629 bytes_read=2162731 bytes_retransmit=0 bytes_invalid=0 send_seq=10162 receive_seq=10162 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998637 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=54.5 th1: temp=54.4 th2: temp=59.6 th3: temp=57.1 sysload=0.52 cputime=397.675 memavail=7393536 print_time=5462.220 buffer_time=2.184 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 34 Hz
Stats 5438.4: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=24909035 bytes_read=3858665 bytes_retransmit=9 bytes_invalid=0 send_seq=468121 receive_seq=468121 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=5372 freq=400016029 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=33790 bytes_read=106060 bytes_retransmit=0 bytes_invalid=0 send_seq=5603 receive_seq=5603 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999271 adj=49997454 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169406 bytes_read=5296628 bytes_retransmit=9 bytes_invalid=0 send_seq=23367 receive_seq=23367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997592 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104682 bytes_read=2553885 bytes_retransmit=9 bytes_invalid=0 send_seq=14213 receive_seq=14213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997445 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34057 bytes_read=1387636 bytes_retransmit=9 bytes_invalid=0 send_seq=5617 receive_seq=5617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997591 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34543 bytes_read=103978 bytes_retransmit=9 bytes_invalid=0 send_seq=5604 receive_seq=5604 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88635 bytes_read=2163087 bytes_retransmit=0 bytes_invalid=0 send_seq=10163 receive_seq=10163 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998637 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=54.5 th1: temp=54.2 th2: temp=59.5 th3: temp=57.2 sysload=0.52 cputime=397.778 memavail=7393536 print_time=5463.114 buffer_time=2.077 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 35 Hz
Stats 5439.4: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=24915871 bytes_read=3859600 bytes_retransmit=9 bytes_invalid=0 send_seq=468246 receive_seq=468246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=6836 freq=400016013 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=33796 bytes_read=106076 bytes_retransmit=0 bytes_invalid=0 send_seq=5604 receive_seq=5604 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999269 adj=49997421 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169412 bytes_read=5296728 bytes_retransmit=9 bytes_invalid=0 send_seq=23368 receive_seq=23368 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997605 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104758 bytes_read=2556960 bytes_retransmit=9 bytes_invalid=0 send_seq=14224 receive_seq=14224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997459 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34063 bytes_read=1387854 bytes_retransmit=9 bytes_invalid=0 send_seq=5618 receive_seq=5618 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997601 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34549 bytes_read=103994 bytes_retransmit=9 bytes_invalid=0 send_seq=5605 receive_seq=5605 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88641 bytes_read=2163443 bytes_retransmit=0 bytes_invalid=0 send_seq=10164 receive_seq=10164 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998638 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=54.8 th1: temp=54.3 th2: temp=59.6 th3: temp=57.2 sysload=0.52 cputime=397.880 memavail=7393536 print_time=5464.049 buffer_time=2.011 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 36 Hz
Stats 5440.4: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=24924239 bytes_read=3860684 bytes_retransmit=9 bytes_invalid=0 send_seq=468395 receive_seq=468395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=8280 freq=400016001 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=33802 bytes_read=106092 bytes_retransmit=0 bytes_invalid=0 send_seq=5605 receive_seq=5605 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999268 adj=49997398 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169418 bytes_read=5296870 bytes_retransmit=9 bytes_invalid=0 send_seq=23369 receive_seq=23369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997634 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104834 bytes_read=2560044 bytes_retransmit=9 bytes_invalid=0 send_seq=14235 receive_seq=14235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997488 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34069 bytes_read=1388148 bytes_retransmit=9 bytes_invalid=0 send_seq=5619 receive_seq=5619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997630 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34555 bytes_read=104010 bytes_retransmit=9 bytes_invalid=0 send_seq=5606 receive_seq=5606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88647 bytes_read=2163799 bytes_retransmit=0 bytes_invalid=0 send_seq=10165 receive_seq=10165 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998644 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=54.6 th1: temp=54.1 th2: temp=59.5 th3: temp=56.9 sysload=0.48 cputime=397.996 memavail=7393548 print_time=5465.258 buffer_time=2.220 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 37 Hz
Stats 5441.4: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24933033 bytes_read=3861800 bytes_retransmit=9 bytes_invalid=0 send_seq=468553 receive_seq=468553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=6269 freq=400015992 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33808 bytes_read=106121 bytes_retransmit=0 bytes_invalid=0 send_seq=5606 receive_seq=5606 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999266 adj=49997354 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169424 bytes_read=5296970 bytes_retransmit=9 bytes_invalid=0 send_seq=23370 receive_seq=23370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997650 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104910 bytes_read=2563102 bytes_retransmit=9 bytes_invalid=0 send_seq=14246 receive_seq=14246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997556 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34075 bytes_read=1388382 bytes_retransmit=9 bytes_invalid=0 send_seq=5620 receive_seq=5620 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34561 bytes_read=104026 bytes_retransmit=9 bytes_invalid=0 send_seq=5607 receive_seq=5607 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88653 bytes_read=2164155 bytes_retransmit=0 bytes_invalid=0 send_seq=10166 receive_seq=10166 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998702 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=54.7 th1: temp=54.2 th2: temp=59.6 th3: temp=57.1 sysload=0.48 cputime=398.103 memavail=7393584 print_time=5466.113 buffer_time=2.075 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 38 Hz
Stats 5442.4: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24940235 bytes_read=3862770 bytes_retransmit=9 bytes_invalid=0 send_seq=468685 receive_seq=468685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=7704 freq=400016069 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33814 bytes_read=106137 bytes_retransmit=0 bytes_invalid=0 send_seq=5607 receive_seq=5607 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999264 adj=49997337 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169430 bytes_read=5297070 bytes_retransmit=9 bytes_invalid=0 send_seq=23371 receive_seq=23371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997674 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=104986 bytes_read=2566158 bytes_retransmit=9 bytes_invalid=0 send_seq=14257 receive_seq=14257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997564 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34081 bytes_read=1388616 bytes_retransmit=9 bytes_invalid=0 send_seq=5621 receive_seq=5621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34567 bytes_read=104053 bytes_retransmit=9 bytes_invalid=0 send_seq=5608 receive_seq=5608 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88659 bytes_read=2164511 bytes_retransmit=0 bytes_invalid=0 send_seq=10167 receive_seq=10167 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998692 coil_temp=17.0 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=54.5 th1: temp=54.3 th2: temp=59.5 th3: temp=57.1 sysload=0.48 cputime=398.221 memavail=7392828 print_time=5467.059 buffer_time=2.021 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 39 Hz
Testing frequency 40 Hz
Stats 5443.4: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24949145 bytes_read=3863870 bytes_retransmit=9 bytes_invalid=0 send_seq=468838 receive_seq=468838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=8984 freq=400016050 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33820 bytes_read=106153 bytes_retransmit=0 bytes_invalid=0 send_seq=5608 receive_seq=5608 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999262 adj=49997179 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169436 bytes_read=5297198 bytes_retransmit=9 bytes_invalid=0 send_seq=23372 receive_seq=23372 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997504 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105062 bytes_read=2569244 bytes_retransmit=9 bytes_invalid=0 send_seq=14268 receive_seq=14268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997386 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34087 bytes_read=1388925 bytes_retransmit=9 bytes_invalid=0 send_seq=5622 receive_seq=5622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997550 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34573 bytes_read=104069 bytes_retransmit=9 bytes_invalid=0 send_seq=5609 receive_seq=5609 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999416 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88665 bytes_read=2164867 bytes_retransmit=0 bytes_invalid=0 send_seq=10168 receive_seq=10168 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998604 coil_temp=17.0 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=54.6 th1: temp=54.1 th2: temp=59.5 th3: temp=57.0 sysload=0.48 cputime=398.353 memavail=7387032 print_time=5468.284 buffer_time=2.244 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5444.4: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24958235 bytes_read=3864990 bytes_retransmit=9 bytes_invalid=0 send_seq=469000 receive_seq=469000 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=7146 freq=400016029 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33826 bytes_read=106169 bytes_retransmit=0 bytes_invalid=0 send_seq=5609 receive_seq=5609 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999261 adj=49997210 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169442 bytes_read=5297298 bytes_retransmit=9 bytes_invalid=0 send_seq=23373 receive_seq=23373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997573 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105138 bytes_read=2572318 bytes_retransmit=9 bytes_invalid=0 send_seq=14279 receive_seq=14279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997444 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34093 bytes_read=1389159 bytes_retransmit=9 bytes_invalid=0 send_seq=5623 receive_seq=5623 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997603 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34579 bytes_read=104085 bytes_retransmit=9 bytes_invalid=0 send_seq=5610 receive_seq=5610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88671 bytes_read=2165223 bytes_retransmit=0 bytes_invalid=0 send_seq=10169 receive_seq=10169 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998632 coil_temp=17.0 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=54.7 th1: temp=54.2 th2: temp=59.4 th3: temp=57.2 sysload=0.48 cputime=398.463 memavail=7392708 print_time=5469.162 buffer_time=2.122 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 41 Hz
Stats 5445.4: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24965727 bytes_read=3865980 bytes_retransmit=9 bytes_invalid=0 send_seq=469136 receive_seq=469136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=8799 freq=400016017 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33832 bytes_read=106185 bytes_retransmit=0 bytes_invalid=0 send_seq=5610 receive_seq=5610 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999260 adj=49997235 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169448 bytes_read=5297412 bytes_retransmit=9 bytes_invalid=0 send_seq=23374 receive_seq=23374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997632 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105214 bytes_read=2575375 bytes_retransmit=9 bytes_invalid=0 send_seq=14290 receive_seq=14290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997486 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34099 bytes_read=1389393 bytes_retransmit=9 bytes_invalid=0 send_seq=5624 receive_seq=5624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34585 bytes_read=104101 bytes_retransmit=9 bytes_invalid=0 send_seq=5611 receive_seq=5611 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88677 bytes_read=2165579 bytes_retransmit=0 bytes_invalid=0 send_seq=10170 receive_seq=10170 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998644 coil_temp=17.0 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=54.6 th1: temp=53.8 th2: temp=59.4 th3: temp=57.1 sysload=0.52 cputime=398.567 memavail=7392484 print_time=5470.086 buffer_time=2.046 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 42 Hz
Testing frequency 43 Hz
Stats 5446.4: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24975101 bytes_read=3867170 bytes_retransmit=9 bytes_invalid=0 send_seq=469303 receive_seq=469303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=10388 freq=400016008 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33838 bytes_read=106214 bytes_retransmit=0 bytes_invalid=0 send_seq=5611 receive_seq=5611 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999258 adj=49997237 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169454 bytes_read=5297540 bytes_retransmit=9 bytes_invalid=0 send_seq=23375 receive_seq=23375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997656 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105290 bytes_read=2578520 bytes_retransmit=9 bytes_invalid=0 send_seq=14301 receive_seq=14301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34105 bytes_read=1389687 bytes_retransmit=9 bytes_invalid=0 send_seq=5625 receive_seq=5625 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34591 bytes_read=104117 bytes_retransmit=9 bytes_invalid=0 send_seq=5612 receive_seq=5612 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88683 bytes_read=2165935 bytes_retransmit=0 bytes_invalid=0 send_seq=10171 receive_seq=10171 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998681 coil_temp=17.0 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=55.0 th1: temp=54.1 th2: temp=59.5 th3: temp=57.0 sysload=0.52 cputime=398.687 memavail=7392484 print_time=5471.289 buffer_time=2.248 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5447.4: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24984704 bytes_read=3868300 bytes_retransmit=9 bytes_invalid=0 send_seq=469467 receive_seq=469467 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=43 upcoming_bytes=8109 freq=400016015 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33844 bytes_read=106230 bytes_retransmit=0 bytes_invalid=0 send_seq=5612 receive_seq=5612 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999257 adj=49997238 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169460 bytes_read=5297640 bytes_retransmit=9 bytes_invalid=0 send_seq=23376 receive_seq=23376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000197 adj=63997663 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105366 bytes_read=2581577 bytes_retransmit=9 bytes_invalid=0 send_seq=14312 receive_seq=14312 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997513 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34111 bytes_read=1389921 bytes_retransmit=9 bytes_invalid=0 send_seq=5626 receive_seq=5626 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34597 bytes_read=104144 bytes_retransmit=9 bytes_invalid=0 send_seq=5613 receive_seq=5613 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88689 bytes_read=2166291 bytes_retransmit=0 bytes_invalid=0 send_seq=10172 receive_seq=10172 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998675 coil_temp=17.0 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=54.6 th1: temp=54.0 th2: temp=59.4 th3: temp=57.1 sysload=0.52 cputime=398.796 memavail=7392736 print_time=5472.192 buffer_time=2.151 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Testing frequency 44 Hz
Stats 5448.4: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=24993007 bytes_read=3869370 bytes_retransmit=9 bytes_invalid=0 send_seq=469619 receive_seq=469619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=9232 freq=400016002 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33850 bytes_read=106246 bytes_retransmit=0 bytes_invalid=0 send_seq=5613 receive_seq=5613 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997215 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169466 bytes_read=5297740 bytes_retransmit=9 bytes_invalid=0 send_seq=23377 receive_seq=23377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997644 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105442 bytes_read=2584633 bytes_retransmit=9 bytes_invalid=0 send_seq=14323 receive_seq=14323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997493 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34117 bytes_read=1390170 bytes_retransmit=9 bytes_invalid=0 send_seq=5627 receive_seq=5627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34603 bytes_read=104160 bytes_retransmit=9 bytes_invalid=0 send_seq=5614 receive_seq=5614 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88695 bytes_read=2166647 bytes_retransmit=0 bytes_invalid=0 send_seq=10173 receive_seq=10173 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998669 coil_temp=17.0 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=54.6 th1: temp=53.8 th2: temp=59.6 th3: temp=57.1 sysload=0.52 cputime=398.905 memavail=7392736 print_time=5473.099 buffer_time=2.057 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 45 Hz
Testing frequency 46 Hz
Stats 5449.4: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25002483 bytes_read=3870554 bytes_retransmit=9 bytes_invalid=0 send_seq=469788 receive_seq=469788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=10900 freq=400016004 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33856 bytes_read=106262 bytes_retransmit=0 bytes_invalid=0 send_seq=5614 receive_seq=5614 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999254 adj=49997225 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169472 bytes_read=5297868 bytes_retransmit=9 bytes_invalid=0 send_seq=23378 receive_seq=23378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997685 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105511 bytes_read=2587711 bytes_retransmit=9 bytes_invalid=0 send_seq=14333 receive_seq=14333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997514 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34123 bytes_read=1390464 bytes_retransmit=9 bytes_invalid=0 send_seq=5628 receive_seq=5628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34609 bytes_read=104176 bytes_retransmit=9 bytes_invalid=0 send_seq=5615 receive_seq=5615 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88701 bytes_read=2167003 bytes_retransmit=0 bytes_invalid=0 send_seq=10174 receive_seq=10174 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998672 coil_temp=17.0 refs=0 mcu_temp=20.18 supply_voltage=3.012 th0: temp=54.7 th1: temp=54.1 th2: temp=59.3 th3: temp=56.9 sysload=0.52 cputime=399.031 memavail=7392736 print_time=5474.309 buffer_time=2.266 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5450.4: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25012358 bytes_read=3871709 bytes_retransmit=9 bytes_invalid=0 send_seq=469957 receive_seq=469957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=8468 freq=400015990 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33862 bytes_read=106278 bytes_retransmit=0 bytes_invalid=0 send_seq=5615 receive_seq=5615 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997216 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169478 bytes_read=5297982 bytes_retransmit=9 bytes_invalid=0 send_seq=23379 receive_seq=23379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997675 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105587 bytes_read=2590769 bytes_retransmit=9 bytes_invalid=0 send_seq=14344 receive_seq=14344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997499 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34129 bytes_read=1390698 bytes_retransmit=9 bytes_invalid=0 send_seq=5629 receive_seq=5629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34615 bytes_read=104192 bytes_retransmit=9 bytes_invalid=0 send_seq=5616 receive_seq=5616 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88707 bytes_read=2167359 bytes_retransmit=0 bytes_invalid=0 send_seq=10175 receive_seq=10175 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998659 coil_temp=17.0 refs=0 mcu_temp=20.18 supply_voltage=3.012 th0: temp=54.6 th1: temp=54.0 th2: temp=59.4 th3: temp=57.1 sysload=0.48 cputime=399.148 memavail=7392736 print_time=5475.197 buffer_time=2.153 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 47 Hz
Stats 5451.4: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=25020903 bytes_read=3872800 bytes_retransmit=9 bytes_invalid=0 send_seq=470110 receive_seq=470110 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=9724 freq=400015993 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33868 bytes_read=106307 bytes_retransmit=0 bytes_invalid=0 send_seq=5616 receive_seq=5616 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997231 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169484 bytes_read=5298082 bytes_retransmit=9 bytes_invalid=0 send_seq=23380 receive_seq=23380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997693 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105663 bytes_read=2593827 bytes_retransmit=9 bytes_invalid=0 send_seq=14355 receive_seq=14355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34135 bytes_read=1390932 bytes_retransmit=9 bytes_invalid=0 send_seq=5630 receive_seq=5630 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34621 bytes_read=104208 bytes_retransmit=9 bytes_invalid=0 send_seq=5617 receive_seq=5617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88713 bytes_read=2167715 bytes_retransmit=0 bytes_invalid=0 send_seq=10176 receive_seq=10176 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998665 coil_temp=17.0 refs=0 mcu_temp=20.18 supply_voltage=3.012 th0: temp=54.7 th1: temp=54.0 th2: temp=59.3 th3: temp=56.9 sysload=0.48 cputime=399.260 memavail=7392736 print_time=5476.125 buffer_time=2.081 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 48 Hz
Testing frequency 49 Hz
Stats 5452.4: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=25030421 bytes_read=3873959 bytes_retransmit=9 bytes_invalid=0 send_seq=470274 receive_seq=470274 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=23 upcoming_bytes=11794 freq=400015980 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33874 bytes_read=106323 bytes_retransmit=0 bytes_invalid=0 send_seq=5617 receive_seq=5617 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997221 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169490 bytes_read=5298210 bytes_retransmit=9 bytes_invalid=0 send_seq=23381 receive_seq=23381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997677 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105739 bytes_read=2596913 bytes_retransmit=9 bytes_invalid=0 send_seq=14366 receive_seq=14366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997513 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34141 bytes_read=1391226 bytes_retransmit=9 bytes_invalid=0 send_seq=5631 receive_seq=5631 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34627 bytes_read=104235 bytes_retransmit=9 bytes_invalid=0 send_seq=5618 receive_seq=5618 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88719 bytes_read=2168071 bytes_retransmit=0 bytes_invalid=0 send_seq=10177 receive_seq=10177 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998653 coil_temp=17.0 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=54.6 th1: temp=54.1 th2: temp=59.3 th3: temp=57.1 sysload=0.48 cputime=399.388 memavail=7392736 print_time=5477.327 buffer_time=2.282 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5453.4: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=25040578 bytes_read=3875132 bytes_retransmit=9 bytes_invalid=0 send_seq=470447 receive_seq=470447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=9425 freq=400015976 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33880 bytes_read=106339 bytes_retransmit=0 bytes_invalid=0 send_seq=5618 receive_seq=5618 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997241 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169496 bytes_read=5298310 bytes_retransmit=9 bytes_invalid=0 send_seq=23382 receive_seq=23382 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63997713 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105815 bytes_read=2600028 bytes_retransmit=9 bytes_invalid=0 send_seq=14377 receive_seq=14377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34147 bytes_read=1391475 bytes_retransmit=9 bytes_invalid=0 send_seq=5632 receive_seq=5632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34633 bytes_read=104251 bytes_retransmit=9 bytes_invalid=0 send_seq=5619 receive_seq=5619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88725 bytes_read=2168427 bytes_retransmit=0 bytes_invalid=0 send_seq=10178 receive_seq=10178 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998670 coil_temp=17.0 refs=0 mcu_temp=20.18 supply_voltage=3.012 th0: temp=54.6 th1: temp=54.0 th2: temp=59.3 th3: temp=57.0 sysload=0.48 cputime=399.503 memavail=7392748 print_time=5478.226 buffer_time=2.180 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 50 Hz
Stats 5454.4: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=25049472 bytes_read=3876240 bytes_retransmit=9 bytes_invalid=0 send_seq=470607 receive_seq=470607 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=10467 freq=400015959 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33886 bytes_read=106355 bytes_retransmit=0 bytes_invalid=0 send_seq=5619 receive_seq=5619 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997239 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169502 bytes_read=5298410 bytes_retransmit=9 bytes_invalid=0 send_seq=23383 receive_seq=23383 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997716 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105891 bytes_read=2603102 bytes_retransmit=9 bytes_invalid=0 send_seq=14388 receive_seq=14388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997544 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34153 bytes_read=1391709 bytes_retransmit=9 bytes_invalid=0 send_seq=5633 receive_seq=5633 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34639 bytes_read=104267 bytes_retransmit=9 bytes_invalid=0 send_seq=5620 receive_seq=5620 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88731 bytes_read=2168783 bytes_retransmit=0 bytes_invalid=0 send_seq=10179 receive_seq=10179 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998663 coil_temp=17.0 refs=0 mcu_temp=20.17 supply_voltage=3.012 th0: temp=54.6 th1: temp=54.0 th2: temp=59.4 th3: temp=57.1 sysload=0.48 cputime=399.618 memavail=7392748 print_time=5479.133 buffer_time=2.087 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 51 Hz
Testing frequency 52 Hz
Stats 5455.4: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=25059524 bytes_read=3877474 bytes_retransmit=9 bytes_invalid=0 send_seq=470786 receive_seq=470786 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=12153 freq=400015951 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33892 bytes_read=106371 bytes_retransmit=0 bytes_invalid=0 send_seq=5620 receive_seq=5620 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997263 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169508 bytes_read=5298552 bytes_retransmit=9 bytes_invalid=0 send_seq=23384 receive_seq=23384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997760 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=105967 bytes_read=2606187 bytes_retransmit=9 bytes_invalid=0 send_seq=14399 receive_seq=14399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997579 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34159 bytes_read=1392003 bytes_retransmit=9 bytes_invalid=0 send_seq=5634 receive_seq=5634 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997707 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34645 bytes_read=104283 bytes_retransmit=9 bytes_invalid=0 send_seq=5621 receive_seq=5621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88737 bytes_read=2169139 bytes_retransmit=0 bytes_invalid=0 send_seq=10180 receive_seq=10180 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998674 coil_temp=17.0 refs=0 mcu_temp=20.18 supply_voltage=3.012 th0: temp=54.4 th1: temp=54.0 th2: temp=59.3 th3: temp=57.0 sysload=0.60 cputime=399.749 memavail=7392748 print_time=5480.333 buffer_time=2.286 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5456.4: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=25069975 bytes_read=3878720 bytes_retransmit=9 bytes_invalid=0 send_seq=470970 receive_seq=470970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=9972 freq=400015941 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33898 bytes_read=106400 bytes_retransmit=0 bytes_invalid=0 send_seq=5621 receive_seq=5621 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997277 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169514 bytes_read=5298652 bytes_retransmit=9 bytes_invalid=0 send_seq=23385 receive_seq=23385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997812 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106043 bytes_read=2609245 bytes_retransmit=9 bytes_invalid=0 send_seq=14410 receive_seq=14410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997570 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34165 bytes_read=1392237 bytes_retransmit=9 bytes_invalid=0 send_seq=5635 receive_seq=5635 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997765 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34651 bytes_read=104299 bytes_retransmit=9 bytes_invalid=0 send_seq=5622 receive_seq=5622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88743 bytes_read=2169495 bytes_retransmit=0 bytes_invalid=0 send_seq=10181 receive_seq=10181 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998672 coil_temp=17.0 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=54.7 th1: temp=54.3 th2: temp=59.3 th3: temp=56.9 sysload=0.60 cputime=399.866 memavail=7392256 print_time=5481.233 buffer_time=2.186 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 53 Hz
Stats 5457.4: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=25079047 bytes_read=3879859 bytes_retransmit=9 bytes_invalid=0 send_seq=471133 receive_seq=471133 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=11264 freq=400016072 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33904 bytes_read=106416 bytes_retransmit=0 bytes_invalid=0 send_seq=5622 receive_seq=5622 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997275 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169520 bytes_read=5298752 bytes_retransmit=9 bytes_invalid=0 send_seq=23386 receive_seq=23386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997812 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106119 bytes_read=2612301 bytes_retransmit=9 bytes_invalid=0 send_seq=14421 receive_seq=14421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997597 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34171 bytes_read=1392471 bytes_retransmit=9 bytes_invalid=0 send_seq=5636 receive_seq=5636 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997758 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34657 bytes_read=104326 bytes_retransmit=9 bytes_invalid=0 send_seq=5623 receive_seq=5623 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88749 bytes_read=2169851 bytes_retransmit=0 bytes_invalid=0 send_seq=10182 receive_seq=10182 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998674 coil_temp=17.0 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=54.6 th1: temp=54.0 th2: temp=59.3 th3: temp=57.0 sysload=0.60 cputime=399.979 memavail=7392268 print_time=5482.146 buffer_time=2.098 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 54 Hz
Testing frequency 55 Hz
Stats 5458.4: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=25089448 bytes_read=3881099 bytes_retransmit=9 bytes_invalid=0 send_seq=471316 receive_seq=471316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=9096 freq=400016070 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33910 bytes_read=106432 bytes_retransmit=0 bytes_invalid=0 send_seq=5623 receive_seq=5623 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997046 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169526 bytes_read=5298880 bytes_retransmit=9 bytes_invalid=0 send_seq=23387 receive_seq=23387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997522 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106195 bytes_read=2615387 bytes_retransmit=9 bytes_invalid=0 send_seq=14432 receive_seq=14432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997317 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34177 bytes_read=1392780 bytes_retransmit=9 bytes_invalid=0 send_seq=5637 receive_seq=5637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999565 adj=47997539 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34663 bytes_read=104342 bytes_retransmit=9 bytes_invalid=0 send_seq=5624 receive_seq=5624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999404 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88755 bytes_read=2170207 bytes_retransmit=0 bytes_invalid=0 send_seq=10183 receive_seq=10183 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998540 coil_temp=17.0 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=54.7 th1: temp=54.0 th2: temp=59.4 th3: temp=56.9 sysload=0.60 cputime=400.103 memavail=7392268 print_time=5483.043 buffer_time=1.995 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5459.4: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=25100402 bytes_read=3882369 bytes_retransmit=9 bytes_invalid=0 send_seq=471508 receive_seq=471508 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=10516 freq=400016070 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33916 bytes_read=106448 bytes_retransmit=0 bytes_invalid=0 send_seq=5624 receive_seq=5624 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997069 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169532 bytes_read=5298980 bytes_retransmit=9 bytes_invalid=0 send_seq=23388 receive_seq=23388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997534 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106271 bytes_read=2618461 bytes_retransmit=9 bytes_invalid=0 send_seq=14443 receive_seq=14443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997340 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34183 bytes_read=1393014 bytes_retransmit=9 bytes_invalid=0 send_seq=5638 receive_seq=5638 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34669 bytes_read=104358 bytes_retransmit=9 bytes_invalid=0 send_seq=5625 receive_seq=5625 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999408 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88761 bytes_read=2170563 bytes_retransmit=0 bytes_invalid=0 send_seq=10184 receive_seq=10184 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998547 coil_temp=17.0 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=54.5 th1: temp=53.9 th2: temp=59.2 th3: temp=57.0 sysload=0.60 cputime=400.232 memavail=7392276 print_time=5484.262 buffer_time=2.213 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 56 Hz
Stats 5460.4: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=25109563 bytes_read=3883508 bytes_retransmit=9 bytes_invalid=0 send_seq=471671 receive_seq=471671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=11656 freq=400016214 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33922 bytes_read=106464 bytes_retransmit=0 bytes_invalid=0 send_seq=5625 receive_seq=5625 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997115 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169538 bytes_read=5299094 bytes_retransmit=9 bytes_invalid=0 send_seq=23389 receive_seq=23389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997591 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106347 bytes_read=2621517 bytes_retransmit=9 bytes_invalid=0 send_seq=14454 receive_seq=14454 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997399 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34189 bytes_read=1393248 bytes_retransmit=9 bytes_invalid=0 send_seq=5639 receive_seq=5639 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997616 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34675 bytes_read=104374 bytes_retransmit=9 bytes_invalid=0 send_seq=5626 receive_seq=5626 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999416 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88767 bytes_read=2170911 bytes_retransmit=0 bytes_invalid=0 send_seq=10185 receive_seq=10185 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998572 coil_temp=17.0 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=54.7 th1: temp=53.9 th2: temp=59.3 th3: temp=57.0 sysload=0.55 cputime=400.347 memavail=7390512 print_time=5485.139 buffer_time=2.090 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 57 Hz
Stats 5461.4: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25120280 bytes_read=3884794 bytes_retransmit=9 bytes_invalid=0 send_seq=471860 receive_seq=471860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=9710 freq=400016188 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33928 bytes_read=106493 bytes_retransmit=0 bytes_invalid=0 send_seq=5626 receive_seq=5626 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49996891 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169544 bytes_read=5299222 bytes_retransmit=9 bytes_invalid=0 send_seq=23390 receive_seq=23390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997296 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106423 bytes_read=2624659 bytes_retransmit=9 bytes_invalid=0 send_seq=14465 receive_seq=14465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997137 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34195 bytes_read=1393542 bytes_retransmit=9 bytes_invalid=0 send_seq=5640 receive_seq=5640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997393 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34681 bytes_read=104390 bytes_retransmit=9 bytes_invalid=0 send_seq=5627 receive_seq=5627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999366 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88773 bytes_read=2171256 bytes_retransmit=0 bytes_invalid=0 send_seq=10186 receive_seq=10186 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998433 coil_temp=17.0 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=54.8 th1: temp=53.8 th2: temp=59.2 th3: temp=56.9 sysload=0.55 cputime=400.479 memavail=7393020 print_time=5486.066 buffer_time=2.017 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 58 Hz
Testing frequency 59 Hz
Stats 5462.4: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25131408 bytes_read=3886094 bytes_retransmit=9 bytes_invalid=0 send_seq=472058 receive_seq=472058 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=11360 freq=400016158 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33934 bytes_read=106509 bytes_retransmit=0 bytes_invalid=0 send_seq=5627 receive_seq=5627 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49996971 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169550 bytes_read=5299322 bytes_retransmit=9 bytes_invalid=0 send_seq=23391 receive_seq=23391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997403 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106492 bytes_read=2627692 bytes_retransmit=9 bytes_invalid=0 send_seq=14475 receive_seq=14475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997233 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34201 bytes_read=1393776 bytes_retransmit=9 bytes_invalid=0 send_seq=5641 receive_seq=5641 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997457 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34687 bytes_read=104417 bytes_retransmit=9 bytes_invalid=0 send_seq=5628 receive_seq=5628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999406 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88779 bytes_read=2171600 bytes_retransmit=0 bytes_invalid=0 send_seq=10187 receive_seq=10187 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998514 coil_temp=17.0 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=54.8 th1: temp=53.7 th2: temp=59.4 th3: temp=56.9 sysload=0.55 cputime=400.691 memavail=7393180 print_time=5487.279 buffer_time=2.229 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5463.4: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25141092 bytes_read=3887283 bytes_retransmit=9 bytes_invalid=0 send_seq=472231 receive_seq=472231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=12264 freq=400016151 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33940 bytes_read=106525 bytes_retransmit=0 bytes_invalid=0 send_seq=5628 receive_seq=5628 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997086 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169556 bytes_read=5299422 bytes_retransmit=9 bytes_invalid=0 send_seq=23392 receive_seq=23392 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997533 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106568 bytes_read=2630750 bytes_retransmit=9 bytes_invalid=0 send_seq=14486 receive_seq=14486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997357 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34207 bytes_read=1394025 bytes_retransmit=9 bytes_invalid=0 send_seq=5642 receive_seq=5642 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997539 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34693 bytes_read=104433 bytes_retransmit=9 bytes_invalid=0 send_seq=5629 receive_seq=5629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88785 bytes_read=2171945 bytes_retransmit=0 bytes_invalid=0 send_seq=10188 receive_seq=10188 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998602 coil_temp=17.0 refs=0 mcu_temp=20.17 supply_voltage=3.012 th0: temp=54.6 th1: temp=53.8 th2: temp=59.3 th3: temp=56.9 sysload=0.55 cputime=400.806 memavail=7393180 print_time=5488.162 buffer_time=2.112 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 60 Hz
Stats 5464.4: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25151938 bytes_read=3888574 bytes_retransmit=9 bytes_invalid=0 send_seq=472425 receive_seq=472425 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=10407 freq=400016169 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33946 bytes_read=106541 bytes_retransmit=0 bytes_invalid=0 send_seq=5629 receive_seq=5629 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997105 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169562 bytes_read=5299550 bytes_retransmit=9 bytes_invalid=0 send_seq=23393 receive_seq=23393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997572 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106644 bytes_read=2633852 bytes_retransmit=9 bytes_invalid=0 send_seq=14497 receive_seq=14497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997388 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34213 bytes_read=1394319 bytes_retransmit=9 bytes_invalid=0 send_seq=5643 receive_seq=5643 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997566 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34699 bytes_read=104449 bytes_retransmit=9 bytes_invalid=0 send_seq=5630 receive_seq=5630 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88791 bytes_read=2172290 bytes_retransmit=0 bytes_invalid=0 send_seq=10189 receive_seq=10189 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998602 coil_temp=17.0 refs=0 mcu_temp=20.16 supply_voltage=3.012 th0: temp=54.9 th1: temp=53.9 th2: temp=59.3 th3: temp=57.0 sysload=0.55 cputime=400.928 memavail=7393180 print_time=5489.081 buffer_time=2.031 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 61 Hz
Testing frequency 62 Hz
Stats 5465.4: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25163385 bytes_read=3889889 bytes_retransmit=9 bytes_invalid=0 send_seq=472626 receive_seq=472626 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=11868 freq=400016159 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33952 bytes_read=106557 bytes_retransmit=0 bytes_invalid=0 send_seq=5630 receive_seq=5630 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997087 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169568 bytes_read=5299664 bytes_retransmit=9 bytes_invalid=0 send_seq=23394 receive_seq=23394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997536 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106720 bytes_read=2636910 bytes_retransmit=9 bytes_invalid=0 send_seq=14508 receive_seq=14508 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997358 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34219 bytes_read=1394553 bytes_retransmit=9 bytes_invalid=0 send_seq=5644 receive_seq=5644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997573 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34705 bytes_read=104465 bytes_retransmit=9 bytes_invalid=0 send_seq=5631 receive_seq=5631 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999418 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88797 bytes_read=2172635 bytes_retransmit=0 bytes_invalid=0 send_seq=10190 receive_seq=10190 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998580 coil_temp=17.0 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=54.9 th1: temp=53.9 th2: temp=59.4 th3: temp=56.9 sysload=0.51 cputime=401.061 memavail=7393180 print_time=5490.286 buffer_time=2.236 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5466.4: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25173296 bytes_read=3891064 bytes_retransmit=9 bytes_invalid=0 send_seq=472794 receive_seq=472793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=12832 freq=400016148 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33958 bytes_read=106586 bytes_retransmit=0 bytes_invalid=0 send_seq=5631 receive_seq=5631 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997138 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169574 bytes_read=5299764 bytes_retransmit=9 bytes_invalid=0 send_seq=23395 receive_seq=23395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997665 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106796 bytes_read=2639968 bytes_retransmit=9 bytes_invalid=0 send_seq=14519 receive_seq=14519 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997407 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34225 bytes_read=1394787 bytes_retransmit=9 bytes_invalid=0 send_seq=5645 receive_seq=5645 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997589 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34711 bytes_read=104481 bytes_retransmit=9 bytes_invalid=0 send_seq=5632 receive_seq=5632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88803 bytes_read=2172980 bytes_retransmit=0 bytes_invalid=0 send_seq=10191 receive_seq=10191 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998599 coil_temp=17.0 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=54.9 th1: temp=53.8 th2: temp=59.4 th3: temp=57.0 sysload=0.51 cputime=401.175 memavail=7393180 print_time=5491.179 buffer_time=2.127 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 63 Hz
Stats 5467.4: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25184283 bytes_read=3892354 bytes_retransmit=9 bytes_invalid=0 send_seq=472986 receive_seq=472986 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=11243 freq=400016188 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33964 bytes_read=106602 bytes_retransmit=0 bytes_invalid=0 send_seq=5632 receive_seq=5632 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997168 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169580 bytes_read=5299892 bytes_retransmit=9 bytes_invalid=0 send_seq=23396 receive_seq=23396 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997748 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106872 bytes_read=2643053 bytes_retransmit=9 bytes_invalid=0 send_seq=14530 receive_seq=14530 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997433 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34231 bytes_read=1395081 bytes_retransmit=9 bytes_invalid=0 send_seq=5646 receive_seq=5646 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997599 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34717 bytes_read=104508 bytes_retransmit=9 bytes_invalid=0 send_seq=5633 receive_seq=5633 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88809 bytes_read=2173325 bytes_retransmit=0 bytes_invalid=0 send_seq=10192 receive_seq=10192 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998611 coil_temp=17.0 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=54.6 th1: temp=53.9 th2: temp=59.2 th3: temp=56.9 sysload=0.51 cputime=401.298 memavail=7393180 print_time=5492.102 buffer_time=2.050 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 64 Hz
Testing frequency 65 Hz
Stats 5468.4: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25196085 bytes_read=3893699 bytes_retransmit=9 bytes_invalid=0 send_seq=473193 receive_seq=473193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=12792 freq=400016194 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33970 bytes_read=106618 bytes_retransmit=0 bytes_invalid=0 send_seq=5633 receive_seq=5633 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997107 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169586 bytes_read=5299992 bytes_retransmit=9 bytes_invalid=0 send_seq=23397 receive_seq=23397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997720 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=106948 bytes_read=2646169 bytes_retransmit=9 bytes_invalid=0 send_seq=14541 receive_seq=14541 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997358 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34237 bytes_read=1395330 bytes_retransmit=9 bytes_invalid=0 send_seq=5647 receive_seq=5647 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997527 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34723 bytes_read=104524 bytes_retransmit=9 bytes_invalid=0 send_seq=5634 receive_seq=5634 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999416 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88815 bytes_read=2173673 bytes_retransmit=0 bytes_invalid=0 send_seq=10193 receive_seq=10193 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998565 coil_temp=17.0 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=54.9 th1: temp=53.7 th2: temp=59.3 th3: temp=57.0 sysload=0.51 cputime=401.431 memavail=7393180 print_time=5493.305 buffer_time=2.252 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5469.4: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25206251 bytes_read=3894913 bytes_retransmit=9 bytes_invalid=0 send_seq=473371 receive_seq=473371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=13660 freq=400016177 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33976 bytes_read=106634 bytes_retransmit=0 bytes_invalid=0 send_seq=5634 receive_seq=5634 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997128 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169592 bytes_read=5300092 bytes_retransmit=9 bytes_invalid=0 send_seq=23398 receive_seq=23398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997734 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107024 bytes_read=2649243 bytes_retransmit=9 bytes_invalid=0 send_seq=14552 receive_seq=14552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997375 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34243 bytes_read=1395564 bytes_retransmit=9 bytes_invalid=0 send_seq=5648 receive_seq=5648 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997541 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34729 bytes_read=104540 bytes_retransmit=9 bytes_invalid=0 send_seq=5635 receive_seq=5635 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88821 bytes_read=2174029 bytes_retransmit=0 bytes_invalid=0 send_seq=10194 receive_seq=10194 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998575 coil_temp=17.0 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=54.5 th1: temp=54.0 th2: temp=59.2 th3: temp=57.0 sysload=0.51 cputime=401.545 memavail=7393180 print_time=5494.171 buffer_time=2.118 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 66 Hz
Stats 5470.4: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25217753 bytes_read=3896248 bytes_retransmit=9 bytes_invalid=0 send_seq=473573 receive_seq=473573 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=20 upcoming_bytes=12162 freq=400016160 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33982 bytes_read=106650 bytes_retransmit=0 bytes_invalid=0 send_seq=5635 receive_seq=5635 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997163 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169598 bytes_read=5300234 bytes_retransmit=9 bytes_invalid=0 send_seq=23399 receive_seq=23399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997830 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107100 bytes_read=2652327 bytes_retransmit=9 bytes_invalid=0 send_seq=14563 receive_seq=14563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997431 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34249 bytes_read=1395858 bytes_retransmit=9 bytes_invalid=0 send_seq=5649 receive_seq=5649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997564 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34735 bytes_read=104556 bytes_retransmit=9 bytes_invalid=0 send_seq=5636 receive_seq=5636 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88827 bytes_read=2174385 bytes_retransmit=0 bytes_invalid=0 send_seq=10195 receive_seq=10195 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998591 coil_temp=17.0 refs=0 mcu_temp=20.16 supply_voltage=3.012 th0: temp=54.7 th1: temp=53.9 th2: temp=59.3 th3: temp=57.0 sysload=0.47 cputime=401.664 memavail=7393180 print_time=5495.116 buffer_time=2.062 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 67 Hz
Testing frequency 68 Hz
Stats 5471.4: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25230060 bytes_read=3897654 bytes_retransmit=9 bytes_invalid=0 send_seq=473789 receive_seq=473789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=13724 freq=400016137 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33988 bytes_read=106679 bytes_retransmit=0 bytes_invalid=0 send_seq=5636 receive_seq=5636 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997184 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169604 bytes_read=5300334 bytes_retransmit=9 bytes_invalid=0 send_seq=23400 receive_seq=23400 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997865 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107176 bytes_read=2655386 bytes_retransmit=9 bytes_invalid=0 send_seq=14574 receive_seq=14574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997468 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34255 bytes_read=1396092 bytes_retransmit=9 bytes_invalid=0 send_seq=5650 receive_seq=5650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997595 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34741 bytes_read=104572 bytes_retransmit=9 bytes_invalid=0 send_seq=5637 receive_seq=5637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88833 bytes_read=2174741 bytes_retransmit=0 bytes_invalid=0 send_seq=10196 receive_seq=10196 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998655 coil_temp=17.0 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=54.9 th1: temp=54.1 th2: temp=59.3 th3: temp=57.0 sysload=0.47 cputime=401.800 memavail=7393180 print_time=5496.318 buffer_time=2.264 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5472.4: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25240604 bytes_read=3898908 bytes_retransmit=9 bytes_invalid=0 send_seq=473975 receive_seq=473975 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=14179 freq=400016113 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=33994 bytes_read=106695 bytes_retransmit=0 bytes_invalid=0 send_seq=5637 receive_seq=5637 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997226 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169610 bytes_read=5300434 bytes_retransmit=9 bytes_invalid=0 send_seq=23401 receive_seq=23401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997814 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107245 bytes_read=2658421 bytes_retransmit=9 bytes_invalid=0 send_seq=14584 receive_seq=14584 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997600 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34261 bytes_read=1396326 bytes_retransmit=9 bytes_invalid=0 send_seq=5651 receive_seq=5651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34747 bytes_read=104599 bytes_retransmit=9 bytes_invalid=0 send_seq=5638 receive_seq=5638 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88839 bytes_read=2175097 bytes_retransmit=0 bytes_invalid=0 send_seq=10197 receive_seq=10197 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998671 coil_temp=17.0 refs=0 mcu_temp=20.16 supply_voltage=3.012 th0: temp=54.7 th1: temp=54.0 th2: temp=59.3 th3: temp=56.8 sysload=0.47 cputime=401.916 memavail=7393180 print_time=5497.197 buffer_time=2.142 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 69 Hz
Stats 5473.4: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25252380 bytes_read=3900273 bytes_retransmit=9 bytes_invalid=0 send_seq=474183 receive_seq=474183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=12729 freq=400016094 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34000 bytes_read=106711 bytes_retransmit=0 bytes_invalid=0 send_seq=5638 receive_seq=5638 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997264 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169616 bytes_read=5300562 bytes_retransmit=9 bytes_invalid=0 send_seq=23402 receive_seq=23402 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997807 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107321 bytes_read=2661505 bytes_retransmit=9 bytes_invalid=0 send_seq=14595 receive_seq=14595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997622 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34267 bytes_read=1396635 bytes_retransmit=9 bytes_invalid=0 send_seq=5652 receive_seq=5652 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34753 bytes_read=104615 bytes_retransmit=9 bytes_invalid=0 send_seq=5639 receive_seq=5639 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88845 bytes_read=2175453 bytes_retransmit=0 bytes_invalid=0 send_seq=10198 receive_seq=10198 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998721 coil_temp=17.0 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=54.8 th1: temp=53.7 th2: temp=59.3 th3: temp=56.9 sysload=0.47 cputime=402.042 memavail=7393180 print_time=5498.123 buffer_time=2.068 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 70 Hz
Testing frequency 71 Hz
Stats 5474.4: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25264793 bytes_read=3901663 bytes_retransmit=9 bytes_invalid=0 send_seq=474399 receive_seq=474399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=14583 freq=400016083 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34006 bytes_read=106727 bytes_retransmit=0 bytes_invalid=0 send_seq=5639 receive_seq=5639 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997286 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169622 bytes_read=5300662 bytes_retransmit=9 bytes_invalid=0 send_seq=23403 receive_seq=23403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997796 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107397 bytes_read=2664579 bytes_retransmit=9 bytes_invalid=0 send_seq=14606 receive_seq=14606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997632 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34273 bytes_read=1396869 bytes_retransmit=9 bytes_invalid=0 send_seq=5653 receive_seq=5653 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997692 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34759 bytes_read=104631 bytes_retransmit=9 bytes_invalid=0 send_seq=5640 receive_seq=5640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88851 bytes_read=2175809 bytes_retransmit=0 bytes_invalid=0 send_seq=10199 receive_seq=10199 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998722 coil_temp=17.0 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=54.7 th1: temp=53.9 th2: temp=59.4 th3: temp=56.9 sysload=0.47 cputime=402.178 memavail=7393180 print_time=5499.330 buffer_time=2.273 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5475.4: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25275647 bytes_read=3902935 bytes_retransmit=9 bytes_invalid=0 send_seq=474590 receive_seq=474590 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=15090 freq=400016094 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34012 bytes_read=106743 bytes_retransmit=0 bytes_invalid=0 send_seq=5640 receive_seq=5640 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997285 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169628 bytes_read=5300776 bytes_retransmit=9 bytes_invalid=0 send_seq=23404 receive_seq=23404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997846 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107473 bytes_read=2667637 bytes_retransmit=9 bytes_invalid=0 send_seq=14617 receive_seq=14617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997599 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34279 bytes_read=1397103 bytes_retransmit=9 bytes_invalid=0 send_seq=5654 receive_seq=5654 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34765 bytes_read=104647 bytes_retransmit=9 bytes_invalid=0 send_seq=5641 receive_seq=5641 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88857 bytes_read=2176165 bytes_retransmit=0 bytes_invalid=0 send_seq=10200 receive_seq=10200 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998705 coil_temp=17.0 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=54.6 th1: temp=54.0 th2: temp=59.6 th3: temp=56.9 sysload=0.43 cputime=402.298 memavail=7393104 print_time=5500.214 buffer_time=2.157 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 72 Hz
Stats 5476.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25287737 bytes_read=3904331 bytes_retransmit=9 bytes_invalid=0 send_seq=474801 receive_seq=474801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=13791 freq=400016069 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=34018 bytes_read=106772 bytes_retransmit=0 bytes_invalid=0 send_seq=5641 receive_seq=5641 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997266 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169634 bytes_read=5300904 bytes_retransmit=9 bytes_invalid=0 send_seq=23405 receive_seq=23405 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000245 adj=63997787 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107549 bytes_read=2670781 bytes_retransmit=9 bytes_invalid=0 send_seq=14628 receive_seq=14628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997576 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34285 bytes_read=1397397 bytes_retransmit=9 bytes_invalid=0 send_seq=5655 receive_seq=5655 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34771 bytes_read=104663 bytes_retransmit=9 bytes_invalid=0 send_seq=5642 receive_seq=5642 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88863 bytes_read=2176521 bytes_retransmit=0 bytes_invalid=0 send_seq=10201 receive_seq=10201 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998694 coil_temp=17.0 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=54.9 th1: temp=53.8 th2: temp=59.5 th3: temp=57.1 sysload=0.43 cputime=402.424 memavail=7392776 print_time=5501.136 buffer_time=2.078 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 73 Hz
Testing frequency 74 Hz
Stats 5477.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25300653 bytes_read=3905756 bytes_retransmit=9 bytes_invalid=0 send_seq=475024 receive_seq=475024 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=15919 freq=400016061 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=34024 bytes_read=106788 bytes_retransmit=0 bytes_invalid=0 send_seq=5642 receive_seq=5642 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997288 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169640 bytes_read=5301004 bytes_retransmit=9 bytes_invalid=0 send_seq=23406 receive_seq=23406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000242 adj=63997933 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107625 bytes_read=2673838 bytes_retransmit=9 bytes_invalid=0 send_seq=14639 receive_seq=14639 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997605 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34291 bytes_read=1397631 bytes_retransmit=9 bytes_invalid=0 send_seq=5656 receive_seq=5656 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34777 bytes_read=104690 bytes_retransmit=9 bytes_invalid=0 send_seq=5643 receive_seq=5643 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88869 bytes_read=2176877 bytes_retransmit=0 bytes_invalid=0 send_seq=10202 receive_seq=10202 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998727 coil_temp=17.0 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=54.8 th1: temp=53.8 th2: temp=59.4 th3: temp=56.9 sysload=0.43 cputime=402.566 memavail=7392776 print_time=5502.354 buffer_time=2.295 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5478.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25311933 bytes_read=3907080 bytes_retransmit=9 bytes_invalid=0 send_seq=475221 receive_seq=475221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=15800 freq=400016079 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=34030 bytes_read=106804 bytes_retransmit=0 bytes_invalid=0 send_seq=5643 receive_seq=5643 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997280 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169646 bytes_read=5301104 bytes_retransmit=9 bytes_invalid=0 send_seq=23407 receive_seq=23407 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000241 adj=63997830 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107701 bytes_read=2676896 bytes_retransmit=9 bytes_invalid=0 send_seq=14650 receive_seq=14650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997574 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34297 bytes_read=1397880 bytes_retransmit=9 bytes_invalid=0 send_seq=5657 receive_seq=5657 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34783 bytes_read=104706 bytes_retransmit=9 bytes_invalid=0 send_seq=5644 receive_seq=5644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88875 bytes_read=2177233 bytes_retransmit=0 bytes_invalid=0 send_seq=10203 receive_seq=10203 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998707 coil_temp=17.0 refs=0 mcu_temp=20.14 supply_voltage=3.012 th0: temp=54.8 th1: temp=53.9 th2: temp=59.3 th3: temp=56.9 sysload=0.43 cputime=402.698 memavail=7395144 print_time=5503.230 buffer_time=2.171 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 75 Hz
Stats 5479.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25324289 bytes_read=3908475 bytes_retransmit=9 bytes_invalid=0 send_seq=475438 receive_seq=475438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=14695 freq=400016056 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=34036 bytes_read=106820 bytes_retransmit=0 bytes_invalid=0 send_seq=5644 receive_seq=5644 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997293 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169652 bytes_read=5301228 bytes_retransmit=9 bytes_invalid=0 send_seq=23408 receive_seq=23408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997771 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107777 bytes_read=2679993 bytes_retransmit=9 bytes_invalid=0 send_seq=14661 receive_seq=14661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997527 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34303 bytes_read=1398174 bytes_retransmit=9 bytes_invalid=0 send_seq=5658 receive_seq=5658 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34789 bytes_read=104722 bytes_retransmit=9 bytes_invalid=0 send_seq=5645 receive_seq=5645 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88881 bytes_read=2177589 bytes_retransmit=0 bytes_invalid=0 send_seq=10204 receive_seq=10204 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998686 coil_temp=17.0 refs=0 mcu_temp=20.14 supply_voltage=3.012 th0: temp=54.8 th1: temp=54.1 th2: temp=59.1 th3: temp=57.0 sysload=0.43 cputime=402.825 memavail=7395144 print_time=5504.154 buffer_time=2.095 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 76 Hz
Testing frequency 77 Hz
Stats 5480.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25337555 bytes_read=3909940 bytes_retransmit=9 bytes_invalid=0 send_seq=475669 receive_seq=475669 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=52 upcoming_bytes=16316 freq=400016045 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=34042 bytes_read=106836 bytes_retransmit=0 bytes_invalid=0 send_seq=5645 receive_seq=5645 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997317 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169658 bytes_read=5301335 bytes_retransmit=9 bytes_invalid=0 send_seq=23409 receive_seq=23409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997762 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107853 bytes_read=2683034 bytes_retransmit=9 bytes_invalid=0 send_seq=14672 receive_seq=14672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997559 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34309 bytes_read=1398408 bytes_retransmit=9 bytes_invalid=0 send_seq=5659 receive_seq=5659 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34795 bytes_read=104738 bytes_retransmit=9 bytes_invalid=0 send_seq=5646 receive_seq=5646 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88887 bytes_read=2177945 bytes_retransmit=0 bytes_invalid=0 send_seq=10205 receive_seq=10205 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998703 coil_temp=17.0 refs=0 mcu_temp=20.14 supply_voltage=3.012 th0: temp=54.8 th1: temp=54.0 th2: temp=59.1 th3: temp=57.0 sysload=0.39 cputime=402.968 memavail=7395152 print_time=5505.357 buffer_time=2.298 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5481.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25349029 bytes_read=3911305 bytes_retransmit=9 bytes_invalid=0 send_seq=475872 receive_seq=475871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=16104 freq=400016034 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34048 bytes_read=106865 bytes_retransmit=0 bytes_invalid=0 send_seq=5646 receive_seq=5646 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997305 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169664 bytes_read=5301428 bytes_retransmit=9 bytes_invalid=0 send_seq=23410 receive_seq=23410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997729 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=107929 bytes_read=2686074 bytes_retransmit=9 bytes_invalid=0 send_seq=14683 receive_seq=14683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997552 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34315 bytes_read=1398642 bytes_retransmit=9 bytes_invalid=0 send_seq=5660 receive_seq=5660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34801 bytes_read=104754 bytes_retransmit=9 bytes_invalid=0 send_seq=5647 receive_seq=5647 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88893 bytes_read=2178301 bytes_retransmit=0 bytes_invalid=0 send_seq=10206 receive_seq=10206 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998689 coil_temp=17.0 refs=0 mcu_temp=20.14 supply_voltage=3.012 th0: temp=54.8 th1: temp=53.7 th2: temp=59.3 th3: temp=57.0 sysload=0.39 cputime=403.089 memavail=7395152 print_time=5506.225 buffer_time=2.165 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 78 Hz
Stats 5482.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25361587 bytes_read=3912715 bytes_retransmit=9 bytes_invalid=0 send_seq=476091 receive_seq=476091 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=15820 freq=400016061 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34054 bytes_read=106881 bytes_retransmit=0 bytes_invalid=0 send_seq=5647 receive_seq=5647 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997313 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169670 bytes_read=5301547 bytes_retransmit=9 bytes_invalid=0 send_seq=23411 receive_seq=23411 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997711 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108005 bytes_read=2689141 bytes_retransmit=9 bytes_invalid=0 send_seq=14694 receive_seq=14694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34321 bytes_read=1398936 bytes_retransmit=9 bytes_invalid=0 send_seq=5661 receive_seq=5661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997683 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34807 bytes_read=104781 bytes_retransmit=9 bytes_invalid=0 send_seq=5648 receive_seq=5648 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88899 bytes_read=2178657 bytes_retransmit=0 bytes_invalid=0 send_seq=10207 receive_seq=10207 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998686 coil_temp=17.0 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=54.8 th1: temp=54.0 th2: temp=59.4 th3: temp=56.9 sysload=0.39 cputime=403.216 memavail=7395152 print_time=5507.174 buffer_time=2.114 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 79 Hz
Testing frequency 80 Hz
Stats 5483.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25375093 bytes_read=3914200 bytes_retransmit=9 bytes_invalid=0 send_seq=476326 receive_seq=476326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=29 upcoming_bytes=17311 freq=400016055 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34060 bytes_read=106897 bytes_retransmit=0 bytes_invalid=0 send_seq=5648 receive_seq=5648 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997262 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169676 bytes_read=5301643 bytes_retransmit=9 bytes_invalid=0 send_seq=23412 receive_seq=23412 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997630 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108081 bytes_read=2692243 bytes_retransmit=9 bytes_invalid=0 send_seq=14705 receive_seq=14705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34327 bytes_read=1399185 bytes_retransmit=9 bytes_invalid=0 send_seq=5662 receive_seq=5662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34813 bytes_read=104797 bytes_retransmit=9 bytes_invalid=0 send_seq=5649 receive_seq=5649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88905 bytes_read=2179013 bytes_retransmit=0 bytes_invalid=0 send_seq=10208 receive_seq=10208 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998652 coil_temp=17.0 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=54.7 th1: temp=53.9 th2: temp=59.3 th3: temp=57.0 sysload=0.39 cputime=403.358 memavail=7397520 print_time=5508.369 buffer_time=2.304 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5484.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25386975 bytes_read=3915579 bytes_retransmit=9 bytes_invalid=0 send_seq=476534 receive_seq=476534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=16857 freq=400016057 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34066 bytes_read=106913 bytes_retransmit=0 bytes_invalid=0 send_seq=5649 receive_seq=5649 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997250 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169682 bytes_read=5301757 bytes_retransmit=9 bytes_invalid=0 send_seq=23413 receive_seq=23413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997618 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108157 bytes_read=2695317 bytes_retransmit=9 bytes_invalid=0 send_seq=14716 receive_seq=14716 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997592 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34333 bytes_read=1399419 bytes_retransmit=9 bytes_invalid=0 send_seq=5663 receive_seq=5663 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34819 bytes_read=104813 bytes_retransmit=9 bytes_invalid=0 send_seq=5650 receive_seq=5650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88911 bytes_read=2179369 bytes_retransmit=0 bytes_invalid=0 send_seq=10209 receive_seq=10209 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998654 coil_temp=17.0 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=54.9 th1: temp=53.9 th2: temp=59.4 th3: temp=57.0 sysload=0.39 cputime=403.482 memavail=7397532 print_time=5509.245 buffer_time=2.179 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 81 Hz
Stats 5485.4: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25399613 bytes_read=3916992 bytes_retransmit=9 bytes_invalid=0 send_seq=476756 receive_seq=476755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=16564 freq=400016051 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34072 bytes_read=106929 bytes_retransmit=0 bytes_invalid=0 send_seq=5650 receive_seq=5650 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997243 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169688 bytes_read=5301885 bytes_retransmit=9 bytes_invalid=0 send_seq=23414 receive_seq=23414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997589 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108233 bytes_read=2698401 bytes_retransmit=9 bytes_invalid=0 send_seq=14727 receive_seq=14727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997564 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34339 bytes_read=1399713 bytes_retransmit=9 bytes_invalid=0 send_seq=5664 receive_seq=5664 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997630 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34825 bytes_read=104829 bytes_retransmit=9 bytes_invalid=0 send_seq=5651 receive_seq=5651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88917 bytes_read=2179725 bytes_retransmit=0 bytes_invalid=0 send_seq=10210 receive_seq=10210 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998683 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=54.9 th1: temp=53.8 th2: temp=59.3 th3: temp=57.0 sysload=0.36 cputime=403.611 memavail=7397280 print_time=5510.181 buffer_time=2.115 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 82 Hz
Testing frequency 83 Hz
Stats 5486.5: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25413718 bytes_read=3918535 bytes_retransmit=9 bytes_invalid=0 send_seq=476999 receive_seq=476999 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=18024 freq=400016045 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34078 bytes_read=106958 bytes_retransmit=0 bytes_invalid=0 send_seq=5651 receive_seq=5651 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997257 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169694 bytes_read=5301985 bytes_retransmit=9 bytes_invalid=0 send_seq=23415 receive_seq=23415 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997584 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108309 bytes_read=2701519 bytes_retransmit=9 bytes_invalid=0 send_seq=14738 receive_seq=14738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997555 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34345 bytes_read=1399947 bytes_retransmit=9 bytes_invalid=0 send_seq=5665 receive_seq=5665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34831 bytes_read=104845 bytes_retransmit=9 bytes_invalid=0 send_seq=5652 receive_seq=5652 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88923 bytes_read=2180081 bytes_retransmit=0 bytes_invalid=0 send_seq=10211 receive_seq=10211 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998688 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=54.9 th1: temp=53.9 th2: temp=59.3 th3: temp=57.0 sysload=0.36 cputime=403.758 memavail=7395808 print_time=5511.390 buffer_time=2.315 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 84 Hz
Stats 5487.5: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25425881 bytes_read=3919934 bytes_retransmit=9 bytes_invalid=0 send_seq=477211 receive_seq=477211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=36 upcoming_bytes=16733 freq=400016040 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34084 bytes_read=106974 bytes_retransmit=0 bytes_invalid=0 send_seq=5652 receive_seq=5652 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997249 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169700 bytes_read=5302099 bytes_retransmit=9 bytes_invalid=0 send_seq=23416 receive_seq=23416 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997590 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108385 bytes_read=2704579 bytes_retransmit=9 bytes_invalid=0 send_seq=14749 receive_seq=14749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34351 bytes_read=1400181 bytes_retransmit=9 bytes_invalid=0 send_seq=5666 receive_seq=5666 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997632 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34837 bytes_read=104872 bytes_retransmit=9 bytes_invalid=0 send_seq=5653 receive_seq=5653 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88929 bytes_read=2180437 bytes_retransmit=0 bytes_invalid=0 send_seq=10212 receive_seq=10212 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998686 coil_temp=17.0 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=54.9 th1: temp=54.1 th2: temp=59.3 th3: temp=57.0 sysload=0.36 cputime=403.884 memavail=7395808 print_time=5512.251 buffer_time=2.177 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5488.5: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25438491 bytes_read=3921314 bytes_retransmit=9 bytes_invalid=0 send_seq=477425 receive_seq=477425 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=16992 freq=400016030 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34090 bytes_read=106990 bytes_retransmit=0 bytes_invalid=0 send_seq=5653 receive_seq=5653 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997246 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169706 bytes_read=5302213 bytes_retransmit=9 bytes_invalid=0 send_seq=23417 receive_seq=23417 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997595 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108454 bytes_read=2707641 bytes_retransmit=9 bytes_invalid=0 send_seq=14759 receive_seq=14759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34357 bytes_read=1400490 bytes_retransmit=9 bytes_invalid=0 send_seq=5667 receive_seq=5667 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34843 bytes_read=104888 bytes_retransmit=9 bytes_invalid=0 send_seq=5654 receive_seq=5654 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88935 bytes_read=2180793 bytes_retransmit=0 bytes_invalid=0 send_seq=10213 receive_seq=10213 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998678 coil_temp=17.0 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=54.9 th1: temp=53.9 th2: temp=59.4 th3: temp=56.9 sysload=0.36 cputime=404.013 memavail=7395808 print_time=5513.187 buffer_time=2.111 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 85 Hz
Testing frequency 86 Hz
Stats 5489.5: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25452570 bytes_read=3922844 bytes_retransmit=9 bytes_invalid=0 send_seq=477669 receive_seq=477669 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=18690 freq=400016026 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34096 bytes_read=107006 bytes_retransmit=0 bytes_invalid=0 send_seq=5654 receive_seq=5654 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997255 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=169712 bytes_read=5302313 bytes_retransmit=9 bytes_invalid=0 send_seq=23418 receive_seq=23418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997618 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108530 bytes_read=2710714 bytes_retransmit=9 bytes_invalid=0 send_seq=14770 receive_seq=14770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997615 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34363 bytes_read=1400724 bytes_retransmit=9 bytes_invalid=0 send_seq=5668 receive_seq=5668 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34849 bytes_read=104904 bytes_retransmit=9 bytes_invalid=0 send_seq=5655 receive_seq=5655 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88941 bytes_read=2181149 bytes_retransmit=0 bytes_invalid=0 send_seq=10214 receive_seq=10214 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998676 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=55.1 th1: temp=53.9 th2: temp=59.4 th3: temp=57.0 sysload=0.36 cputime=404.160 memavail=7395808 print_time=5514.391 buffer_time=2.313 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 87 Hz
Stats 5490.5: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25465098 bytes_read=3924258 bytes_retransmit=9 bytes_invalid=0 send_seq=477884 receive_seq=477884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=17269 freq=400016021 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34102 bytes_read=107022 bytes_retransmit=0 bytes_invalid=0 send_seq=5655 receive_seq=5655 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997260 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169718 bytes_read=5302441 bytes_retransmit=9 bytes_invalid=0 send_seq=23419 receive_seq=23419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997614 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108606 bytes_read=2713784 bytes_retransmit=9 bytes_invalid=0 send_seq=14781 receive_seq=14781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997579 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34369 bytes_read=1400958 bytes_retransmit=9 bytes_invalid=0 send_seq=5669 receive_seq=5669 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34855 bytes_read=104920 bytes_retransmit=9 bytes_invalid=0 send_seq=5656 receive_seq=5656 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88947 bytes_read=2181505 bytes_retransmit=0 bytes_invalid=0 send_seq=10215 receive_seq=10215 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998666 coil_temp=17.0 refs=0 mcu_temp=20.12 supply_voltage=3.011 th0: temp=54.8 th1: temp=53.9 th2: temp=59.4 th3: temp=57.1 sysload=0.33 cputime=404.289 memavail=7395808 print_time=5515.255 buffer_time=2.176 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5491.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25478087 bytes_read=3925704 bytes_retransmit=9 bytes_invalid=0 send_seq=478108 receive_seq=478108 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=17392 freq=400016038 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34108 bytes_read=107051 bytes_retransmit=0 bytes_invalid=0 send_seq=5656 receive_seq=5656 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997263 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169724 bytes_read=5302555 bytes_retransmit=9 bytes_invalid=0 send_seq=23420 receive_seq=23420 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997613 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108682 bytes_read=2716856 bytes_retransmit=9 bytes_invalid=0 send_seq=14792 receive_seq=14792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997565 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34375 bytes_read=1401252 bytes_retransmit=9 bytes_invalid=0 send_seq=5670 receive_seq=5670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34861 bytes_read=104936 bytes_retransmit=9 bytes_invalid=0 send_seq=5657 receive_seq=5657 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88953 bytes_read=2181861 bytes_retransmit=0 bytes_invalid=0 send_seq=10216 receive_seq=10216 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998660 coil_temp=17.0 refs=0 mcu_temp=20.12 supply_voltage=3.011 th0: temp=54.6 th1: temp=53.9 th2: temp=59.3 th3: temp=57.1 sysload=0.33 cputime=404.419 memavail=7395808 print_time=5516.195 buffer_time=2.116 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 88 Hz
Testing frequency 89 Hz
Stats 5492.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25492328 bytes_read=3927244 bytes_retransmit=9 bytes_invalid=0 send_seq=478354 receive_seq=478354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=14336 freq=400016022 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34114 bytes_read=107067 bytes_retransmit=0 bytes_invalid=0 send_seq=5657 receive_seq=5657 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997235 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169730 bytes_read=5302655 bytes_retransmit=9 bytes_invalid=0 send_seq=23421 receive_seq=23421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997583 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108758 bytes_read=2719915 bytes_retransmit=9 bytes_invalid=0 send_seq=14803 receive_seq=14803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34381 bytes_read=1401486 bytes_retransmit=9 bytes_invalid=0 send_seq=5671 receive_seq=5671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997611 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34867 bytes_read=104963 bytes_retransmit=9 bytes_invalid=0 send_seq=5658 receive_seq=5658 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88959 bytes_read=2182217 bytes_retransmit=0 bytes_invalid=0 send_seq=10217 receive_seq=10217 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998661 coil_temp=17.0 refs=0 mcu_temp=20.11 supply_voltage=3.011 th0: temp=54.9 th1: temp=53.9 th2: temp=59.4 th3: temp=57.0 sysload=0.33 cputime=404.553 memavail=7395808 print_time=5517.064 buffer_time=1.984 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 90 Hz
Stats 5493.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25505116 bytes_read=3928688 bytes_retransmit=9 bytes_invalid=0 send_seq=478575 receive_seq=478575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=17476 freq=400016002 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34120 bytes_read=107083 bytes_retransmit=0 bytes_invalid=0 send_seq=5658 receive_seq=5658 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997265 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169736 bytes_read=5302769 bytes_retransmit=9 bytes_invalid=0 send_seq=23422 receive_seq=23422 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997609 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108834 bytes_read=2723045 bytes_retransmit=9 bytes_invalid=0 send_seq=14814 receive_seq=14814 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997588 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34387 bytes_read=1401735 bytes_retransmit=9 bytes_invalid=0 send_seq=5672 receive_seq=5672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34873 bytes_read=104979 bytes_retransmit=9 bytes_invalid=0 send_seq=5659 receive_seq=5659 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88965 bytes_read=2182573 bytes_retransmit=0 bytes_invalid=0 send_seq=10218 receive_seq=10218 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998674 coil_temp=17.0 refs=0 mcu_temp=20.11 supply_voltage=3.011 th0: temp=54.6 th1: temp=53.8 th2: temp=59.5 th3: temp=57.1 sysload=0.33 cputime=404.698 memavail=7395800 print_time=5518.272 buffer_time=2.191 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5494.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25517852 bytes_read=3930103 bytes_retransmit=9 bytes_invalid=0 send_seq=478796 receive_seq=478796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=18123 freq=400016037 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34126 bytes_read=107099 bytes_retransmit=0 bytes_invalid=0 send_seq=5659 receive_seq=5659 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997294 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169742 bytes_read=5302883 bytes_retransmit=9 bytes_invalid=0 send_seq=23423 receive_seq=23423 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997657 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108910 bytes_read=2726135 bytes_retransmit=9 bytes_invalid=0 send_seq=14825 receive_seq=14825 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997588 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34393 bytes_read=1402029 bytes_retransmit=9 bytes_invalid=0 send_seq=5673 receive_seq=5673 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34879 bytes_read=104995 bytes_retransmit=9 bytes_invalid=0 send_seq=5660 receive_seq=5660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88971 bytes_read=2182929 bytes_retransmit=0 bytes_invalid=0 send_seq=10219 receive_seq=10219 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998702 coil_temp=17.0 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=54.8 th1: temp=54.0 th2: temp=59.4 th3: temp=57.1 sysload=0.33 cputime=404.827 memavail=7395800 print_time=5519.200 buffer_time=2.120 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 91 Hz
Testing frequency 92 Hz
Stats 5495.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25532583 bytes_read=3931688 bytes_retransmit=9 bytes_invalid=0 send_seq=479052 receive_seq=479051 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=19783 freq=400016022 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34132 bytes_read=107115 bytes_retransmit=0 bytes_invalid=0 send_seq=5660 receive_seq=5660 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997230 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169748 bytes_read=5302983 bytes_retransmit=9 bytes_invalid=0 send_seq=23424 receive_seq=23424 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997568 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=108986 bytes_read=2729193 bytes_retransmit=9 bytes_invalid=0 send_seq=14836 receive_seq=14836 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34399 bytes_read=1402263 bytes_retransmit=9 bytes_invalid=0 send_seq=5674 receive_seq=5674 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997612 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34885 bytes_read=105011 bytes_retransmit=9 bytes_invalid=0 send_seq=5661 receive_seq=5661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88977 bytes_read=2183285 bytes_retransmit=0 bytes_invalid=0 send_seq=10220 receive_seq=10220 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998655 coil_temp=17.0 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=54.8 th1: temp=53.9 th2: temp=59.5 th3: temp=56.9 sysload=0.31 cputime=404.988 memavail=7394948 print_time=5520.410 buffer_time=2.322 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 93 Hz
Stats 5496.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25545775 bytes_read=3933209 bytes_retransmit=9 bytes_invalid=0 send_seq=479283 receive_seq=479283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=17822 freq=400016006 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34144 bytes_read=107160 bytes_retransmit=0 bytes_invalid=0 send_seq=5662 receive_seq=5662 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997250 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169760 bytes_read=5303141 bytes_retransmit=9 bytes_invalid=0 send_seq=23426 receive_seq=23426 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997610 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=109068 bytes_read=2732279 bytes_retransmit=9 bytes_invalid=0 send_seq=14848 receive_seq=14848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34411 bytes_read=1402513 bytes_retransmit=9 bytes_invalid=0 send_seq=5676 receive_seq=5676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34897 bytes_read=105043 bytes_retransmit=9 bytes_invalid=0 send_seq=5663 receive_seq=5663 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88989 bytes_read=2183657 bytes_retransmit=0 bytes_invalid=0 send_seq=10222 receive_seq=10222 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998669 coil_temp=17.0 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=55.0 th1: temp=54.0 th2: temp=59.4 th3: temp=57.1 sysload=0.31 cputime=405.126 memavail=7396584 print_time=5521.280 buffer_time=2.191 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5497.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25558829 bytes_read=3934624 bytes_retransmit=9 bytes_invalid=0 send_seq=479504 receive_seq=479504 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=18595 freq=400015988 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34150 bytes_read=107176 bytes_retransmit=0 bytes_invalid=0 send_seq=5663 receive_seq=5663 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997263 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169766 bytes_read=5303241 bytes_retransmit=9 bytes_invalid=0 send_seq=23427 receive_seq=23427 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997616 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=109144 bytes_read=2735350 bytes_retransmit=9 bytes_invalid=0 send_seq=14859 receive_seq=14859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34417 bytes_read=1402807 bytes_retransmit=9 bytes_invalid=0 send_seq=5677 receive_seq=5677 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34903 bytes_read=105070 bytes_retransmit=9 bytes_invalid=0 send_seq=5664 receive_seq=5664 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=88995 bytes_read=2184013 bytes_retransmit=0 bytes_invalid=0 send_seq=10223 receive_seq=10223 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998668 coil_temp=17.0 refs=0 mcu_temp=20.10 supply_voltage=3.012 th0: temp=54.8 th1: temp=53.8 th2: temp=59.3 th3: temp=57.1 sysload=0.31 cputime=405.257 memavail=7396688 print_time=5522.210 buffer_time=2.121 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 94 Hz
Testing frequency 95 Hz
Stats 5498.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25573544 bytes_read=3936204 bytes_retransmit=9 bytes_invalid=0 send_seq=479758 receive_seq=479758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=15356 freq=400015971 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34156 bytes_read=107192 bytes_retransmit=0 bytes_invalid=0 send_seq=5664 receive_seq=5664 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997284 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169772 bytes_read=5303341 bytes_retransmit=9 bytes_invalid=0 send_seq=23428 receive_seq=23428 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997640 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=109220 bytes_read=2738468 bytes_retransmit=9 bytes_invalid=0 send_seq=14870 receive_seq=14870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997546 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34423 bytes_read=1403056 bytes_retransmit=9 bytes_invalid=0 send_seq=5678 receive_seq=5678 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997693 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34909 bytes_read=105086 bytes_retransmit=9 bytes_invalid=0 send_seq=5665 receive_seq=5665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89001 bytes_read=2184369 bytes_retransmit=0 bytes_invalid=0 send_seq=10224 receive_seq=10224 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998681 coil_temp=17.0 refs=0 mcu_temp=20.10 supply_voltage=3.012 th0: temp=54.9 th1: temp=53.9 th2: temp=59.4 th3: temp=57.2 sysload=0.31 cputime=405.395 memavail=7396688 print_time=5523.082 buffer_time=1.992 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 96 Hz
Stats 5499.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25587030 bytes_read=3937703 bytes_retransmit=9 bytes_invalid=0 send_seq=479990 receive_seq=479990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=18276 freq=400015974 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34162 bytes_read=107208 bytes_retransmit=0 bytes_invalid=0 send_seq=5665 receive_seq=5665 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997311 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169778 bytes_read=5303469 bytes_retransmit=9 bytes_invalid=0 send_seq=23429 receive_seq=23429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997671 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=109296 bytes_read=2741557 bytes_retransmit=9 bytes_invalid=0 send_seq=14881 receive_seq=14881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997583 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34429 bytes_read=1403290 bytes_retransmit=9 bytes_invalid=0 send_seq=5679 receive_seq=5679 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997716 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34915 bytes_read=105102 bytes_retransmit=9 bytes_invalid=0 send_seq=5666 receive_seq=5666 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89007 bytes_read=2184725 bytes_retransmit=0 bytes_invalid=0 send_seq=10225 receive_seq=10225 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998692 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=54.7 th1: temp=54.0 th2: temp=59.4 th3: temp=57.1 sysload=0.31 cputime=405.542 memavail=7396464 print_time=5524.287 buffer_time=2.196 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5500.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25600168 bytes_read=3939148 bytes_retransmit=9 bytes_invalid=0 send_seq=480217 receive_seq=480217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=19052 freq=400015972 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34168 bytes_read=107224 bytes_retransmit=0 bytes_invalid=0 send_seq=5666 receive_seq=5666 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997290 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169784 bytes_read=5303569 bytes_retransmit=9 bytes_invalid=0 send_seq=23430 receive_seq=23430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997728 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=109372 bytes_read=2744627 bytes_retransmit=9 bytes_invalid=0 send_seq=14892 receive_seq=14892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34435 bytes_read=1403584 bytes_retransmit=9 bytes_invalid=0 send_seq=5680 receive_seq=5680 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997696 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34921 bytes_read=105118 bytes_retransmit=9 bytes_invalid=0 send_seq=5667 receive_seq=5667 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89013 bytes_read=2185081 bytes_retransmit=0 bytes_invalid=0 send_seq=10226 receive_seq=10226 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998685 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=55.0 th1: temp=53.8 th2: temp=59.4 th3: temp=57.0 sysload=0.44 cputime=405.676 memavail=7396468 print_time=5525.215 buffer_time=2.123 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 97 Hz
Testing frequency 98 Hz
Stats 5501.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25615263 bytes_read=3940774 bytes_retransmit=9 bytes_invalid=0 send_seq=480477 receive_seq=480477 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=15688 freq=400015969 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34174 bytes_read=107253 bytes_retransmit=0 bytes_invalid=0 send_seq=5667 receive_seq=5667 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997293 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169790 bytes_read=5303683 bytes_retransmit=9 bytes_invalid=0 send_seq=23431 receive_seq=23431 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997706 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=109448 bytes_read=2747686 bytes_retransmit=9 bytes_invalid=0 send_seq=14903 receive_seq=14903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997592 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34441 bytes_read=1403818 bytes_retransmit=9 bytes_invalid=0 send_seq=5681 receive_seq=5681 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997725 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34927 bytes_read=105134 bytes_retransmit=9 bytes_invalid=0 send_seq=5668 receive_seq=5668 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89019 bytes_read=2185437 bytes_retransmit=0 bytes_invalid=0 send_seq=10227 receive_seq=10227 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998680 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=54.8 th1: temp=53.9 th2: temp=59.5 th3: temp=57.0 sysload=0.44 cputime=405.818 memavail=7396468 print_time=5526.090 buffer_time=1.996 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 99 Hz
Stats 5502.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25628835 bytes_read=3942288 bytes_retransmit=9 bytes_invalid=0 send_seq=480712 receive_seq=480712 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=18933 freq=400015955 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34180 bytes_read=107269 bytes_retransmit=0 bytes_invalid=0 send_seq=5668 receive_seq=5668 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997280 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169796 bytes_read=5303811 bytes_retransmit=9 bytes_invalid=0 send_seq=23432 receive_seq=23432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997690 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=109524 bytes_read=2750756 bytes_retransmit=9 bytes_invalid=0 send_seq=14914 receive_seq=14914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997584 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34447 bytes_read=1404052 bytes_retransmit=9 bytes_invalid=0 send_seq=5682 receive_seq=5682 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997711 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34933 bytes_read=105161 bytes_retransmit=9 bytes_invalid=0 send_seq=5669 receive_seq=5669 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89025 bytes_read=2185793 bytes_retransmit=0 bytes_invalid=0 send_seq=10228 receive_seq=10228 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998680 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=54.9 th1: temp=53.9 th2: temp=59.3 th3: temp=57.2 sysload=0.44 cputime=405.968 memavail=7396468 print_time=5527.291 buffer_time=2.196 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5503.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25642332 bytes_read=3943778 bytes_retransmit=9 bytes_invalid=0 send_seq=480948 receive_seq=480948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=19868 freq=400015940 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34186 bytes_read=107285 bytes_retransmit=0 bytes_invalid=0 send_seq=5669 receive_seq=5669 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997291 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169802 bytes_read=5303911 bytes_retransmit=9 bytes_invalid=0 send_seq=23433 receive_seq=23433 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997702 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=109600 bytes_read=2753828 bytes_retransmit=9 bytes_invalid=0 send_seq=14925 receive_seq=14925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997573 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34453 bytes_read=1404361 bytes_retransmit=9 bytes_invalid=0 send_seq=5683 receive_seq=5683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997770 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34939 bytes_read=105177 bytes_retransmit=9 bytes_invalid=0 send_seq=5670 receive_seq=5670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89031 bytes_read=2186149 bytes_retransmit=0 bytes_invalid=0 send_seq=10229 receive_seq=10229 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998710 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=55.0 th1: temp=53.8 th2: temp=59.2 th3: temp=57.1 sysload=0.44 cputime=406.103 memavail=7396468 print_time=5528.224 buffer_time=2.128 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 100 Hz
Testing frequency 101 Hz
Stats 5504.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25657863 bytes_read=3945428 bytes_retransmit=9 bytes_invalid=0 send_seq=481216 receive_seq=481216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=15984 freq=400015927 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34192 bytes_read=107301 bytes_retransmit=0 bytes_invalid=0 send_seq=5670 receive_seq=5670 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997310 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169808 bytes_read=5304011 bytes_retransmit=9 bytes_invalid=0 send_seq=23434 receive_seq=23434 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997722 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=109669 bytes_read=2756937 bytes_retransmit=9 bytes_invalid=0 send_seq=14935 receive_seq=14935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997596 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34459 bytes_read=1404595 bytes_retransmit=9 bytes_invalid=0 send_seq=5684 receive_seq=5684 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997773 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34945 bytes_read=105193 bytes_retransmit=9 bytes_invalid=0 send_seq=5671 receive_seq=5671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89037 bytes_read=2186505 bytes_retransmit=0 bytes_invalid=0 send_seq=10230 receive_seq=10230 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998709 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=55.0 th1: temp=54.1 th2: temp=59.5 th3: temp=57.1 sysload=0.44 cputime=406.248 memavail=7396468 print_time=5529.093 buffer_time=1.995 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 102 Hz
Stats 5505.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25671793 bytes_read=3946972 bytes_retransmit=9 bytes_invalid=0 send_seq=481457 receive_seq=481457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=19323 freq=400015924 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34198 bytes_read=107316 bytes_retransmit=0 bytes_invalid=0 send_seq=5671 receive_seq=5671 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997323 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169814 bytes_read=5304139 bytes_retransmit=9 bytes_invalid=0 send_seq=23435 receive_seq=23435 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997738 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=109745 bytes_read=2760021 bytes_retransmit=9 bytes_invalid=0 send_seq=14946 receive_seq=14946 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997600 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34465 bytes_read=1404829 bytes_retransmit=9 bytes_invalid=0 send_seq=5685 receive_seq=5685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997766 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34951 bytes_read=105209 bytes_retransmit=9 bytes_invalid=0 send_seq=5672 receive_seq=5672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89043 bytes_read=2186861 bytes_retransmit=0 bytes_invalid=0 send_seq=10231 receive_seq=10231 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998708 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=54.8 th1: temp=54.4 th2: temp=59.4 th3: temp=57.2 sysload=0.57 cputime=406.398 memavail=7396508 print_time=5530.298 buffer_time=2.200 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5506.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25685265 bytes_read=3948473 bytes_retransmit=9 bytes_invalid=0 send_seq=481692 receive_seq=481692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=20383 freq=400015911 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34204 bytes_read=107344 bytes_retransmit=0 bytes_invalid=0 send_seq=5672 receive_seq=5672 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997303 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169820 bytes_read=5304253 bytes_retransmit=9 bytes_invalid=0 send_seq=23436 receive_seq=23436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997706 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=109821 bytes_read=2763079 bytes_retransmit=9 bytes_invalid=0 send_seq=14957 receive_seq=14957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997565 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34471 bytes_read=1405123 bytes_retransmit=9 bytes_invalid=0 send_seq=5686 receive_seq=5686 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997724 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34957 bytes_read=105225 bytes_retransmit=9 bytes_invalid=0 send_seq=5673 receive_seq=5673 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89049 bytes_read=2187217 bytes_retransmit=0 bytes_invalid=0 send_seq=10232 receive_seq=10232 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998692 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=55.0 th1: temp=53.9 th2: temp=59.4 th3: temp=57.1 sysload=0.57 cputime=406.535 memavail=7396004 print_time=5531.225 buffer_time=2.126 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 103 Hz
Stats 5507.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25701103 bytes_read=3950143 bytes_retransmit=9 bytes_invalid=0 send_seq=481965 receive_seq=481965 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=16591 freq=400015902 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34210 bytes_read=107359 bytes_retransmit=0 bytes_invalid=0 send_seq=5673 receive_seq=5673 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997317 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169826 bytes_read=5304353 bytes_retransmit=9 bytes_invalid=0 send_seq=23437 receive_seq=23437 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997713 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=109897 bytes_read=2766137 bytes_retransmit=9 bytes_invalid=0 send_seq=14968 receive_seq=14968 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997577 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34477 bytes_read=1405357 bytes_retransmit=9 bytes_invalid=0 send_seq=5687 receive_seq=5687 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997724 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34963 bytes_read=105252 bytes_retransmit=9 bytes_invalid=0 send_seq=5674 receive_seq=5674 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89055 bytes_read=2187573 bytes_retransmit=0 bytes_invalid=0 send_seq=10233 receive_seq=10233 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998694 coil_temp=16.9 refs=0 mcu_temp=20.10 supply_voltage=3.012 th0: temp=55.1 th1: temp=53.9 th2: temp=59.5 th3: temp=57.1 sysload=0.57 cputime=406.676 memavail=7396004 print_time=5532.100 buffer_time=2.001 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 104 Hz
Testing frequency 105 Hz
Stats 5508.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25715351 bytes_read=3951717 bytes_retransmit=9 bytes_invalid=0 send_seq=482212 receive_seq=482212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=19848 freq=400015897 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34216 bytes_read=107374 bytes_retransmit=0 bytes_invalid=0 send_seq=5674 receive_seq=5674 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997331 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169832 bytes_read=5304481 bytes_retransmit=9 bytes_invalid=0 send_seq=23438 receive_seq=23438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997724 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=109973 bytes_read=2769221 bytes_retransmit=9 bytes_invalid=0 send_seq=14979 receive_seq=14979 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997583 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34483 bytes_read=1405606 bytes_retransmit=9 bytes_invalid=0 send_seq=5688 receive_seq=5688 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997719 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34969 bytes_read=105268 bytes_retransmit=9 bytes_invalid=0 send_seq=5675 receive_seq=5675 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.9 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89061 bytes_read=2187929 bytes_retransmit=0 bytes_invalid=0 send_seq=10234 receive_seq=10234 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998699 coil_temp=16.9 refs=0 mcu_temp=20.10 supply_voltage=3.012 th0: temp=54.7 th1: temp=53.9 th2: temp=59.5 th3: temp=57.1 sysload=0.57 cputime=406.838 memavail=7396004 print_time=5533.304 buffer_time=2.205 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.3 pwm=0.000
Stats 5509.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25729172 bytes_read=3953227 bytes_retransmit=9 bytes_invalid=0 send_seq=482452 receive_seq=482452 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=21004 freq=400015896 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34222 bytes_read=107389 bytes_retransmit=0 bytes_invalid=0 send_seq=5675 receive_seq=5675 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997303 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169838 bytes_read=5304581 bytes_retransmit=9 bytes_invalid=0 send_seq=23439 receive_seq=23439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997737 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=110049 bytes_read=2772294 bytes_retransmit=9 bytes_invalid=0 send_seq=14990 receive_seq=14990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997575 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34489 bytes_read=1405900 bytes_retransmit=9 bytes_invalid=0 send_seq=5689 receive_seq=5689 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997697 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34975 bytes_read=105284 bytes_retransmit=9 bytes_invalid=0 send_seq=5676 receive_seq=5676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89067 bytes_read=2188285 bytes_retransmit=0 bytes_invalid=0 send_seq=10235 receive_seq=10235 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998692 coil_temp=16.9 refs=0 mcu_temp=20.10 supply_voltage=3.012 th0: temp=54.8 th1: temp=53.9 th2: temp=59.5 th3: temp=57.1 sysload=0.57 cputime=406.979 memavail=7396004 print_time=5534.235 buffer_time=2.136 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 106 Hz
Stats 5510.5: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25745254 bytes_read=3954902 bytes_retransmit=9 bytes_invalid=0 send_seq=482725 receive_seq=482725 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=16892 freq=400015898 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34228 bytes_read=107404 bytes_retransmit=0 bytes_invalid=0 send_seq=5676 receive_seq=5676 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997297 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169844 bytes_read=5304681 bytes_retransmit=9 bytes_invalid=0 send_seq=23440 receive_seq=23440 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997765 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=110125 bytes_read=2775353 bytes_retransmit=9 bytes_invalid=0 send_seq=15001 receive_seq=15001 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997567 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34495 bytes_read=1406134 bytes_retransmit=9 bytes_invalid=0 send_seq=5690 receive_seq=5690 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997689 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34981 bytes_read=105300 bytes_retransmit=9 bytes_invalid=0 send_seq=5677 receive_seq=5677 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89073 bytes_read=2188641 bytes_retransmit=0 bytes_invalid=0 send_seq=10236 receive_seq=10236 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998687 coil_temp=16.9 refs=0 mcu_temp=20.10 supply_voltage=3.012 th0: temp=55.0 th1: temp=54.1 th2: temp=59.4 th3: temp=57.1 sysload=0.60 cputime=407.123 memavail=7396004 print_time=5535.105 buffer_time=2.005 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 107 Hz
Testing frequency 108 Hz
Stats 5511.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25759725 bytes_read=3956482 bytes_retransmit=9 bytes_invalid=0 send_seq=482970 receive_seq=482970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=20222 freq=400015900 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=34234 bytes_read=107433 bytes_retransmit=0 bytes_invalid=0 send_seq=5677 receive_seq=5677 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997288 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169850 bytes_read=5304823 bytes_retransmit=9 bytes_invalid=0 send_seq=23441 receive_seq=23441 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997734 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=110201 bytes_read=2778441 bytes_retransmit=9 bytes_invalid=0 send_seq=15012 receive_seq=15012 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997543 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34501 bytes_read=1406368 bytes_retransmit=9 bytes_invalid=0 send_seq=5691 receive_seq=5691 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997689 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34987 bytes_read=105316 bytes_retransmit=9 bytes_invalid=0 send_seq=5678 receive_seq=5678 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89079 bytes_read=2188997 bytes_retransmit=0 bytes_invalid=0 send_seq=10237 receive_seq=10237 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998680 coil_temp=16.9 refs=0 mcu_temp=20.10 supply_voltage=3.012 th0: temp=54.9 th1: temp=53.8 th2: temp=59.5 th3: temp=57.1 sysload=0.60 cputime=407.281 memavail=7396004 print_time=5536.308 buffer_time=2.207 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5512.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25773599 bytes_read=3957987 bytes_retransmit=9 bytes_invalid=0 send_seq=483209 receive_seq=483209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=21583 freq=400015946 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=34240 bytes_read=107449 bytes_retransmit=0 bytes_invalid=0 send_seq=5678 receive_seq=5678 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997276 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169856 bytes_read=5304923 bytes_retransmit=9 bytes_invalid=0 send_seq=23442 receive_seq=23442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997776 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=110277 bytes_read=2781555 bytes_retransmit=9 bytes_invalid=0 send_seq=15023 receive_seq=15023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34507 bytes_read=1406662 bytes_retransmit=9 bytes_invalid=0 send_seq=5692 receive_seq=5692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34993 bytes_read=105343 bytes_retransmit=9 bytes_invalid=0 send_seq=5679 receive_seq=5679 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89085 bytes_read=2189353 bytes_retransmit=0 bytes_invalid=0 send_seq=10238 receive_seq=10238 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998672 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=55.1 th1: temp=54.0 th2: temp=59.6 th3: temp=57.1 sysload=0.60 cputime=407.428 memavail=7388972 print_time=5537.238 buffer_time=2.137 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 109 Hz
Stats 5513.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25789912 bytes_read=3959692 bytes_retransmit=9 bytes_invalid=0 send_seq=483488 receive_seq=483488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=17431 freq=400015941 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=34246 bytes_read=107465 bytes_retransmit=0 bytes_invalid=0 send_seq=5679 receive_seq=5679 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997209 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169862 bytes_read=5305023 bytes_retransmit=9 bytes_invalid=0 send_seq=23443 receive_seq=23443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997735 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=110353 bytes_read=2784612 bytes_retransmit=9 bytes_invalid=0 send_seq=15034 receive_seq=15034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997439 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34513 bytes_read=1406911 bytes_retransmit=9 bytes_invalid=0 send_seq=5693 receive_seq=5693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997600 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=34999 bytes_read=105359 bytes_retransmit=9 bytes_invalid=0 send_seq=5680 receive_seq=5680 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999423 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89091 bytes_read=2189709 bytes_retransmit=0 bytes_invalid=0 send_seq=10239 receive_seq=10239 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998676 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=54.9 th1: temp=54.0 th2: temp=59.5 th3: temp=57.0 sysload=0.60 cputime=407.577 memavail=7393920 print_time=5538.109 buffer_time=2.006 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 110 Hz
Testing frequency 111 Hz
Stats 5514.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25804910 bytes_read=3961341 bytes_retransmit=9 bytes_invalid=0 send_seq=483750 receive_seq=483750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=20668 freq=400015930 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=34252 bytes_read=107481 bytes_retransmit=0 bytes_invalid=0 send_seq=5680 receive_seq=5680 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997213 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169868 bytes_read=5305151 bytes_retransmit=9 bytes_invalid=0 send_seq=23444 receive_seq=23444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997717 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=110429 bytes_read=2787713 bytes_retransmit=9 bytes_invalid=0 send_seq=15045 receive_seq=15045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997447 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34519 bytes_read=1407145 bytes_retransmit=9 bytes_invalid=0 send_seq=5694 receive_seq=5694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997611 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35005 bytes_read=105375 bytes_retransmit=9 bytes_invalid=0 send_seq=5681 receive_seq=5681 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89097 bytes_read=2190065 bytes_retransmit=0 bytes_invalid=0 send_seq=10240 receive_seq=10240 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998675 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=55.0 th1: temp=53.9 th2: temp=59.4 th3: temp=57.1 sysload=0.60 cputime=407.738 memavail=7393920 print_time=5539.313 buffer_time=2.210 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5515.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25818924 bytes_read=3962871 bytes_retransmit=9 bytes_invalid=0 send_seq=483994 receive_seq=483994 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=21949 freq=400015919 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=34258 bytes_read=107497 bytes_retransmit=0 bytes_invalid=0 send_seq=5681 receive_seq=5681 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997230 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169874 bytes_read=5305251 bytes_retransmit=9 bytes_invalid=0 send_seq=23445 receive_seq=23445 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997705 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=110505 bytes_read=2790771 bytes_retransmit=9 bytes_invalid=0 send_seq=15056 receive_seq=15056 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34525 bytes_read=1407439 bytes_retransmit=9 bytes_invalid=0 send_seq=5695 receive_seq=5695 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35011 bytes_read=105391 bytes_retransmit=9 bytes_invalid=0 send_seq=5682 receive_seq=5682 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89103 bytes_read=2190421 bytes_retransmit=0 bytes_invalid=0 send_seq=10241 receive_seq=10241 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998686 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=54.9 th1: temp=54.0 th2: temp=59.6 th3: temp=57.2 sysload=0.63 cputime=407.881 memavail=7393668 print_time=5540.239 buffer_time=2.135 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 112 Hz
Stats 5516.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25835694 bytes_read=3964637 bytes_retransmit=9 bytes_invalid=0 send_seq=484283 receive_seq=484282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=17601 freq=400015919 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34264 bytes_read=107526 bytes_retransmit=0 bytes_invalid=0 send_seq=5682 receive_seq=5682 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997257 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169880 bytes_read=5305365 bytes_retransmit=9 bytes_invalid=0 send_seq=23446 receive_seq=23446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997811 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=110574 bytes_read=2793806 bytes_retransmit=9 bytes_invalid=0 send_seq=15066 receive_seq=15066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997495 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34531 bytes_read=1407673 bytes_retransmit=9 bytes_invalid=0 send_seq=5696 receive_seq=5696 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35017 bytes_read=105407 bytes_retransmit=9 bytes_invalid=0 send_seq=5683 receive_seq=5683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89109 bytes_read=2190777 bytes_retransmit=0 bytes_invalid=0 send_seq=10242 receive_seq=10242 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998701 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=55.2 th1: temp=54.2 th2: temp=59.5 th3: temp=57.2 sysload=0.63 cputime=408.028 memavail=7392912 print_time=5541.113 buffer_time=2.008 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 113 Hz
Testing frequency 114 Hz
Stats 5517.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25850670 bytes_read=3966265 bytes_retransmit=9 bytes_invalid=0 send_seq=484540 receive_seq=484540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=20683 freq=400015954 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34270 bytes_read=107542 bytes_retransmit=0 bytes_invalid=0 send_seq=5683 receive_seq=5683 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997262 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169886 bytes_read=5305493 bytes_retransmit=9 bytes_invalid=0 send_seq=23447 receive_seq=23447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997771 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=110650 bytes_read=2796890 bytes_retransmit=9 bytes_invalid=0 send_seq=15077 receive_seq=15077 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997491 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34537 bytes_read=1407922 bytes_retransmit=9 bytes_invalid=0 send_seq=5697 receive_seq=5697 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35023 bytes_read=105434 bytes_retransmit=9 bytes_invalid=0 send_seq=5684 receive_seq=5684 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89115 bytes_read=2191133 bytes_retransmit=0 bytes_invalid=0 send_seq=10243 receive_seq=10243 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998695 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=54.9 th1: temp=54.1 th2: temp=59.6 th3: temp=57.2 sysload=0.63 cputime=408.191 memavail=7392920 print_time=5542.316 buffer_time=2.210 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5518.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25864770 bytes_read=3967795 bytes_retransmit=9 bytes_invalid=0 send_seq=484785 receive_seq=484785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=52 upcoming_bytes=22540 freq=400015935 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34276 bytes_read=107558 bytes_retransmit=0 bytes_invalid=0 send_seq=5684 receive_seq=5684 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997209 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169892 bytes_read=5305593 bytes_retransmit=9 bytes_invalid=0 send_seq=23448 receive_seq=23448 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997651 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=110726 bytes_read=2799947 bytes_retransmit=9 bytes_invalid=0 send_seq=15088 receive_seq=15088 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997432 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34543 bytes_read=1408216 bytes_retransmit=9 bytes_invalid=0 send_seq=5698 receive_seq=5698 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997590 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35029 bytes_read=105450 bytes_retransmit=9 bytes_invalid=0 send_seq=5685 receive_seq=5685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89121 bytes_read=2191489 bytes_retransmit=0 bytes_invalid=0 send_seq=10244 receive_seq=10244 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998644 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=54.9 th1: temp=54.0 th2: temp=59.4 th3: temp=57.2 sysload=0.63 cputime=408.330 memavail=7392920 print_time=5543.249 buffer_time=2.142 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 115 Hz
Stats 5519.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25881489 bytes_read=3969540 bytes_retransmit=9 bytes_invalid=0 send_seq=485072 receive_seq=485072 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=18228 freq=400015936 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34282 bytes_read=107574 bytes_retransmit=0 bytes_invalid=0 send_seq=5685 receive_seq=5685 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997242 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169898 bytes_read=5305693 bytes_retransmit=9 bytes_invalid=0 send_seq=23449 receive_seq=23449 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997671 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=110802 bytes_read=2803081 bytes_retransmit=9 bytes_invalid=0 send_seq=15099 receive_seq=15099 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997469 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34549 bytes_read=1408450 bytes_retransmit=9 bytes_invalid=0 send_seq=5699 receive_seq=5699 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997617 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35035 bytes_read=105466 bytes_retransmit=9 bytes_invalid=0 send_seq=5686 receive_seq=5686 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89127 bytes_read=2191845 bytes_retransmit=0 bytes_invalid=0 send_seq=10245 receive_seq=10245 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998662 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=55.1 th1: temp=54.1 th2: temp=59.6 th3: temp=57.1 sysload=0.63 cputime=408.476 memavail=7392920 print_time=5544.119 buffer_time=2.013 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 116 Hz
Testing frequency 117 Hz
Stats 5520.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25896950 bytes_read=3971214 bytes_retransmit=9 bytes_invalid=0 send_seq=485339 receive_seq=485339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=21184 freq=400015924 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34288 bytes_read=107590 bytes_retransmit=0 bytes_invalid=0 send_seq=5686 receive_seq=5686 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997250 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169904 bytes_read=5305821 bytes_retransmit=9 bytes_invalid=0 send_seq=23450 receive_seq=23450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997646 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=110878 bytes_read=2806167 bytes_retransmit=9 bytes_invalid=0 send_seq=15110 receive_seq=15110 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997465 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34555 bytes_read=1408699 bytes_retransmit=9 bytes_invalid=0 send_seq=5700 receive_seq=5700 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997621 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35041 bytes_read=105482 bytes_retransmit=9 bytes_invalid=0 send_seq=5687 receive_seq=5687 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89133 bytes_read=2192201 bytes_retransmit=0 bytes_invalid=0 send_seq=10246 receive_seq=10246 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998652 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=55.2 th1: temp=54.0 th2: temp=59.6 th3: temp=57.0 sysload=0.66 cputime=408.642 memavail=7392920 print_time=5545.317 buffer_time=2.210 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5521.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25911242 bytes_read=3972755 bytes_retransmit=9 bytes_invalid=0 send_seq=485582 receive_seq=485582 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=22780 freq=400015974 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34294 bytes_read=107619 bytes_retransmit=0 bytes_invalid=0 send_seq=5687 receive_seq=5687 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997260 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169910 bytes_read=5305935 bytes_retransmit=9 bytes_invalid=0 send_seq=23451 receive_seq=23451 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997671 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=110954 bytes_read=2809224 bytes_retransmit=9 bytes_invalid=0 send_seq=15121 receive_seq=15121 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34561 bytes_read=1408978 bytes_retransmit=9 bytes_invalid=0 send_seq=5701 receive_seq=5701 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35047 bytes_read=105498 bytes_retransmit=9 bytes_invalid=0 send_seq=5688 receive_seq=5688 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89139 bytes_read=2192557 bytes_retransmit=0 bytes_invalid=0 send_seq=10247 receive_seq=10247 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998673 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=54.9 th1: temp=54.1 th2: temp=59.6 th3: temp=57.1 sysload=0.66 cputime=408.784 memavail=7392920 print_time=5546.255 buffer_time=2.147 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 118 Hz
Stats 5522.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25928285 bytes_read=3974515 bytes_retransmit=9 bytes_invalid=0 send_seq=485872 receive_seq=485872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=18292 freq=400016095 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34300 bytes_read=107635 bytes_retransmit=0 bytes_invalid=0 send_seq=5688 receive_seq=5688 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997175 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169916 bytes_read=5306035 bytes_retransmit=9 bytes_invalid=0 send_seq=23452 receive_seq=23452 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997566 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=111030 bytes_read=2812283 bytes_retransmit=9 bytes_invalid=0 send_seq=15132 receive_seq=15132 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997400 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34567 bytes_read=1409212 bytes_retransmit=9 bytes_invalid=0 send_seq=5702 receive_seq=5702 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997574 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35053 bytes_read=105525 bytes_retransmit=9 bytes_invalid=0 send_seq=5689 receive_seq=5689 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89145 bytes_read=2192913 bytes_retransmit=0 bytes_invalid=0 send_seq=10248 receive_seq=10248 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998620 coil_temp=17.0 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=55.0 th1: temp=54.1 th2: temp=59.6 th3: temp=57.2 sysload=0.66 cputime=408.929 memavail=7392920 print_time=5547.121 buffer_time=2.012 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 119 Hz
Testing frequency 120 Hz
Stats 5523.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25943667 bytes_read=3976179 bytes_retransmit=9 bytes_invalid=0 send_seq=486137 receive_seq=486137 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=21443 freq=400016089 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34306 bytes_read=107651 bytes_retransmit=0 bytes_invalid=0 send_seq=5689 receive_seq=5689 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49996991 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169922 bytes_read=5306163 bytes_retransmit=9 bytes_invalid=0 send_seq=23453 receive_seq=23453 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997305 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=111106 bytes_read=2815368 bytes_retransmit=9 bytes_invalid=0 send_seq=15143 receive_seq=15143 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997268 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34573 bytes_read=1409475 bytes_retransmit=9 bytes_invalid=0 send_seq=5703 receive_seq=5703 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997388 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35059 bytes_read=105541 bytes_retransmit=9 bytes_invalid=0 send_seq=5690 receive_seq=5690 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999389 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89151 bytes_read=2193269 bytes_retransmit=0 bytes_invalid=0 send_seq=10249 receive_seq=10249 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998494 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=54.9 th1: temp=54.0 th2: temp=59.6 th3: temp=57.2 sysload=0.66 cputime=409.093 memavail=7392920 print_time=5548.322 buffer_time=2.212 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5524.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25958182 bytes_read=3977744 bytes_retransmit=9 bytes_invalid=0 send_seq=486388 receive_seq=486388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=23063 freq=400016165 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34312 bytes_read=107667 bytes_retransmit=0 bytes_invalid=0 send_seq=5690 receive_seq=5690 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997071 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169928 bytes_read=5306263 bytes_retransmit=9 bytes_invalid=0 send_seq=23454 receive_seq=23454 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997404 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=111182 bytes_read=2818443 bytes_retransmit=9 bytes_invalid=0 send_seq=15154 receive_seq=15154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997338 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34579 bytes_read=1409735 bytes_retransmit=9 bytes_invalid=0 send_seq=5704 receive_seq=5704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997477 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35065 bytes_read=105557 bytes_retransmit=9 bytes_invalid=0 send_seq=5691 receive_seq=5691 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999403 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89157 bytes_read=2193625 bytes_retransmit=0 bytes_invalid=0 send_seq=10250 receive_seq=10250 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998538 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=54.9 th1: temp=54.1 th2: temp=59.4 th3: temp=57.1 sysload=0.66 cputime=409.237 memavail=7392920 print_time=5549.251 buffer_time=2.141 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 121 Hz
Stats 5525.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25975285 bytes_read=3979519 bytes_retransmit=9 bytes_invalid=0 send_seq=486681 receive_seq=486681 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=18719 freq=400016174 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34318 bytes_read=107683 bytes_retransmit=0 bytes_invalid=0 send_seq=5691 receive_seq=5691 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49996981 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169934 bytes_read=5306363 bytes_retransmit=9 bytes_invalid=0 send_seq=23455 receive_seq=23455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997272 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=111251 bytes_read=2821476 bytes_retransmit=9 bytes_invalid=0 send_seq=15164 receive_seq=15164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997219 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34585 bytes_read=1409953 bytes_retransmit=9 bytes_invalid=0 send_seq=5705 receive_seq=5705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997385 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35071 bytes_read=105573 bytes_retransmit=9 bytes_invalid=0 send_seq=5692 receive_seq=5692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999378 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89163 bytes_read=2193981 bytes_retransmit=0 bytes_invalid=0 send_seq=10251 receive_seq=10251 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998484 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=55.0 th1: temp=54.0 th2: temp=59.6 th3: temp=57.2 sysload=0.61 cputime=409.386 memavail=7392928 print_time=5550.122 buffer_time=2.011 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 122 Hz
Testing frequency 123 Hz
Stats 5526.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=25991024 bytes_read=3981234 bytes_retransmit=9 bytes_invalid=0 send_seq=486953 receive_seq=486953 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=21795 freq=400016192 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34324 bytes_read=107712 bytes_retransmit=0 bytes_invalid=0 send_seq=5692 receive_seq=5692 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49996992 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169940 bytes_read=5306505 bytes_retransmit=9 bytes_invalid=0 send_seq=23456 receive_seq=23456 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997294 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=111327 bytes_read=2824620 bytes_retransmit=9 bytes_invalid=0 send_seq=15175 receive_seq=15175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997233 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34591 bytes_read=1410185 bytes_retransmit=9 bytes_invalid=0 send_seq=5706 receive_seq=5706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997410 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35077 bytes_read=105589 bytes_retransmit=9 bytes_invalid=0 send_seq=5693 receive_seq=5693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999380 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89169 bytes_read=2194321 bytes_retransmit=0 bytes_invalid=0 send_seq=10252 receive_seq=10252 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998490 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=54.9 th1: temp=54.0 th2: temp=59.6 th3: temp=57.2 sysload=0.61 cputime=409.555 memavail=7392688 print_time=5551.323 buffer_time=2.212 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5527.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26005667 bytes_read=3982809 bytes_retransmit=9 bytes_invalid=0 send_seq=487206 receive_seq=487206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=23593 freq=400016175 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34330 bytes_read=107728 bytes_retransmit=0 bytes_invalid=0 send_seq=5693 receive_seq=5693 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997033 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169946 bytes_read=5306605 bytes_retransmit=9 bytes_invalid=0 send_seq=23457 receive_seq=23457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997359 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=111403 bytes_read=2827677 bytes_retransmit=9 bytes_invalid=0 send_seq=15186 receive_seq=15186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997287 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34597 bytes_read=1410445 bytes_retransmit=9 bytes_invalid=0 send_seq=5707 receive_seq=5707 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997441 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35083 bytes_read=105616 bytes_retransmit=9 bytes_invalid=0 send_seq=5694 receive_seq=5694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999400 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89175 bytes_read=2194677 bytes_retransmit=0 bytes_invalid=0 send_seq=10253 receive_seq=10253 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998514 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=55.3 th1: temp=54.1 th2: temp=59.5 th3: temp=57.2 sysload=0.61 cputime=409.700 memavail=7392724 print_time=5552.252 buffer_time=2.140 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 124 Hz
Stats 5528.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26022982 bytes_read=3984602 bytes_retransmit=9 bytes_invalid=0 send_seq=487503 receive_seq=487503 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=19292 freq=400016340 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34336 bytes_read=107744 bytes_retransmit=0 bytes_invalid=0 send_seq=5694 receive_seq=5694 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997078 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169952 bytes_read=5306705 bytes_retransmit=9 bytes_invalid=0 send_seq=23458 receive_seq=23458 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997435 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=111479 bytes_read=2830733 bytes_retransmit=9 bytes_invalid=0 send_seq=15197 receive_seq=15197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997461 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34603 bytes_read=1410678 bytes_retransmit=9 bytes_invalid=0 send_seq=5708 receive_seq=5708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997486 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35089 bytes_read=105632 bytes_retransmit=9 bytes_invalid=0 send_seq=5695 receive_seq=5695 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999408 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89181 bytes_read=2195033 bytes_retransmit=0 bytes_invalid=0 send_seq=10254 receive_seq=10254 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998567 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=54.9 th1: temp=54.0 th2: temp=59.6 th3: temp=57.1 sysload=0.61 cputime=409.849 memavail=7392724 print_time=5553.130 buffer_time=2.018 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 125 Hz
Testing frequency 126 Hz
Stats 5529.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26039044 bytes_read=3986317 bytes_retransmit=9 bytes_invalid=0 send_seq=487779 receive_seq=487779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=22130 freq=400016408 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34342 bytes_read=107760 bytes_retransmit=0 bytes_invalid=0 send_seq=5695 receive_seq=5695 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49996820 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169958 bytes_read=5306833 bytes_retransmit=9 bytes_invalid=0 send_seq=23459 receive_seq=23459 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997102 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=111555 bytes_read=2833839 bytes_retransmit=9 bytes_invalid=0 send_seq=15208 receive_seq=15208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997095 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34609 bytes_read=1410922 bytes_retransmit=9 bytes_invalid=0 send_seq=5709 receive_seq=5709 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997296 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35095 bytes_read=105648 bytes_retransmit=9 bytes_invalid=0 send_seq=5696 receive_seq=5696 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999346 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89187 bytes_read=2195389 bytes_retransmit=0 bytes_invalid=0 send_seq=10255 receive_seq=10255 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998396 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=55.1 th1: temp=54.3 th2: temp=59.3 th3: temp=57.2 sysload=0.61 cputime=410.027 memavail=7388440 print_time=5554.329 buffer_time=2.216 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 127 Hz
Stats 5530.5: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26053965 bytes_read=3987912 bytes_retransmit=9 bytes_invalid=0 send_seq=488036 receive_seq=488036 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=23780 freq=400016361 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34348 bytes_read=107776 bytes_retransmit=0 bytes_invalid=0 send_seq=5696 receive_seq=5696 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49996836 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169964 bytes_read=5306933 bytes_retransmit=9 bytes_invalid=0 send_seq=23460 receive_seq=23460 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997109 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=111631 bytes_read=2836897 bytes_retransmit=9 bytes_invalid=0 send_seq=15219 receive_seq=15219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997052 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34615 bytes_read=1411201 bytes_retransmit=9 bytes_invalid=0 send_seq=5710 receive_seq=5710 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997285 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35101 bytes_read=105664 bytes_retransmit=9 bytes_invalid=0 send_seq=5697 receive_seq=5697 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999345 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89193 bytes_read=2195745 bytes_retransmit=0 bytes_invalid=0 send_seq=10256 receive_seq=10256 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998423 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=55.1 th1: temp=54.0 th2: temp=59.6 th3: temp=57.4 sysload=0.72 cputime=410.185 memavail=7393816 print_time=5555.262 buffer_time=2.148 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5531.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26071325 bytes_read=3989723 bytes_retransmit=9 bytes_invalid=0 send_seq=488333 receive_seq=488333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=19220 freq=400016542 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34354 bytes_read=107805 bytes_retransmit=0 bytes_invalid=0 send_seq=5697 receive_seq=5697 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49996962 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169970 bytes_read=5307047 bytes_retransmit=9 bytes_invalid=0 send_seq=23461 receive_seq=23461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997270 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=111707 bytes_read=2839955 bytes_retransmit=9 bytes_invalid=0 send_seq=15230 receive_seq=15230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997180 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34621 bytes_read=1411435 bytes_retransmit=9 bytes_invalid=0 send_seq=5711 receive_seq=5711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997430 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35107 bytes_read=105680 bytes_retransmit=9 bytes_invalid=0 send_seq=5698 receive_seq=5698 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999373 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89199 bytes_read=2196101 bytes_retransmit=0 bytes_invalid=0 send_seq=10257 receive_seq=10257 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998487 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=55.1 th1: temp=54.1 th2: temp=59.7 th3: temp=57.3 sysload=0.72 cputime=410.335 memavail=7393816 print_time=5556.131 buffer_time=2.016 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 128 Hz
Testing frequency 129 Hz
Stats 5532.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26087477 bytes_read=3991447 bytes_retransmit=9 bytes_invalid=0 send_seq=488611 receive_seq=488610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=22257 freq=400016596 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34360 bytes_read=107821 bytes_retransmit=0 bytes_invalid=0 send_seq=5698 receive_seq=5698 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49996700 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169976 bytes_read=5307175 bytes_retransmit=9 bytes_invalid=0 send_seq=23462 receive_seq=23462 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63996922 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=111783 bytes_read=2843040 bytes_retransmit=9 bytes_invalid=0 send_seq=15241 receive_seq=15241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63996812 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34627 bytes_read=1411699 bytes_retransmit=9 bytes_invalid=0 send_seq=5712 receive_seq=5712 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997173 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35113 bytes_read=105707 bytes_retransmit=9 bytes_invalid=0 send_seq=5699 receive_seq=5699 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999308 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89205 bytes_read=2196457 bytes_retransmit=0 bytes_invalid=0 send_seq=10258 receive_seq=10258 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998310 coil_temp=17.0 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=55.1 th1: temp=54.0 th2: temp=59.3 th3: temp=57.2 sysload=0.72 cputime=410.504 memavail=7393816 print_time=5557.338 buffer_time=2.221 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 130 Hz
Stats 5533.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26102249 bytes_read=3993042 bytes_retransmit=9 bytes_invalid=0 send_seq=488867 receive_seq=488867 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=24040 freq=400016550 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34366 bytes_read=107837 bytes_retransmit=0 bytes_invalid=0 send_seq=5699 receive_seq=5699 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49996766 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169982 bytes_read=5307275 bytes_retransmit=9 bytes_invalid=0 send_seq=23463 receive_seq=23463 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997021 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=111859 bytes_read=2846155 bytes_retransmit=9 bytes_invalid=0 send_seq=15252 receive_seq=15252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63996878 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34633 bytes_read=1411978 bytes_retransmit=9 bytes_invalid=0 send_seq=5713 receive_seq=5713 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997214 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35119 bytes_read=105723 bytes_retransmit=9 bytes_invalid=0 send_seq=5700 receive_seq=5700 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999323 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89211 bytes_read=2196813 bytes_retransmit=0 bytes_invalid=0 send_seq=10259 receive_seq=10259 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998369 coil_temp=17.0 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=55.1 th1: temp=54.0 th2: temp=59.6 th3: temp=57.5 sysload=0.72 cputime=410.653 memavail=7393816 print_time=5558.262 buffer_time=2.145 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5534.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26119807 bytes_read=3994867 bytes_retransmit=9 bytes_invalid=0 send_seq=489170 receive_seq=489170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=19760 freq=400016505 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34372 bytes_read=107853 bytes_retransmit=0 bytes_invalid=0 send_seq=5700 receive_seq=5700 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49996892 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169988 bytes_read=5307375 bytes_retransmit=9 bytes_invalid=0 send_seq=23464 receive_seq=23464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997174 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=111935 bytes_read=2849230 bytes_retransmit=9 bytes_invalid=0 send_seq=15263 receive_seq=15263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997150 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34639 bytes_read=1412212 bytes_retransmit=9 bytes_invalid=0 send_seq=5714 receive_seq=5714 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999565 adj=47997319 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35125 bytes_read=105739 bytes_retransmit=9 bytes_invalid=0 send_seq=5701 receive_seq=5701 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999351 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89217 bytes_read=2197169 bytes_retransmit=0 bytes_invalid=0 send_seq=10260 receive_seq=10260 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998473 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=55.3 th1: temp=53.9 th2: temp=59.7 th3: temp=57.4 sysload=0.72 cputime=410.802 memavail=7393816 print_time=5559.134 buffer_time=2.017 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 131 Hz
Testing frequency 132 Hz
Stats 5535.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26136134 bytes_read=3996601 bytes_retransmit=9 bytes_invalid=0 send_seq=489450 receive_seq=489449 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=22807 freq=400016447 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34378 bytes_read=107869 bytes_retransmit=0 bytes_invalid=0 send_seq=5701 receive_seq=5701 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49996986 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=169994 bytes_read=5307503 bytes_retransmit=9 bytes_invalid=0 send_seq=23465 receive_seq=23465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997297 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=112011 bytes_read=2852314 bytes_retransmit=9 bytes_invalid=0 send_seq=15274 receive_seq=15274 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997245 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34645 bytes_read=1412476 bytes_retransmit=9 bytes_invalid=0 send_seq=5715 receive_seq=5715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997453 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35131 bytes_read=105755 bytes_retransmit=9 bytes_invalid=0 send_seq=5702 receive_seq=5702 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999383 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89223 bytes_read=2197525 bytes_retransmit=0 bytes_invalid=0 send_seq=10261 receive_seq=10261 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998541 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=55.4 th1: temp=54.2 th2: temp=59.7 th3: temp=57.3 sysload=0.74 cputime=410.975 memavail=7393816 print_time=5560.338 buffer_time=2.220 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Stats 5536.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26151299 bytes_read=3998237 bytes_retransmit=9 bytes_invalid=0 send_seq=489712 receive_seq=489711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=25868 freq=400016407 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34384 bytes_read=107898 bytes_retransmit=0 bytes_invalid=0 send_seq=5702 receive_seq=5702 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997136 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170000 bytes_read=5307617 bytes_retransmit=9 bytes_invalid=0 send_seq=23466 receive_seq=23466 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997484 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=112087 bytes_read=2855372 bytes_retransmit=9 bytes_invalid=0 send_seq=15285 receive_seq=15285 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997401 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34651 bytes_read=1412740 bytes_retransmit=9 bytes_invalid=0 send_seq=5716 receive_seq=5716 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997566 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35137 bytes_read=105771 bytes_retransmit=9 bytes_invalid=0 send_seq=5703 receive_seq=5703 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999416 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89229 bytes_read=2197881 bytes_retransmit=0 bytes_invalid=0 send_seq=10262 receive_seq=10262 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998612 coil_temp=17.0 refs=0 mcu_temp=20.10 supply_voltage=3.012 th0: temp=55.2 th1: temp=54.0 th2: temp=59.6 th3: temp=57.3 sysload=0.74 cputime=411.127 memavail=7393816 print_time=5561.315 buffer_time=2.197 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5537.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26169047 bytes_read=4000057 bytes_retransmit=9 bytes_invalid=0 send_seq=490013 receive_seq=490013 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=9816 freq=400016377 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34390 bytes_read=107914 bytes_retransmit=0 bytes_invalid=0 send_seq=5703 receive_seq=5703 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997203 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170006 bytes_read=5307717 bytes_retransmit=9 bytes_invalid=0 send_seq=23467 receive_seq=23467 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997579 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=112156 bytes_read=2858407 bytes_retransmit=9 bytes_invalid=0 send_seq=15295 receive_seq=15295 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997463 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34657 bytes_read=1412974 bytes_retransmit=9 bytes_invalid=0 send_seq=5717 receive_seq=5717 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997614 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35143 bytes_read=105798 bytes_retransmit=9 bytes_invalid=0 send_seq=5704 receive_seq=5704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89235 bytes_read=2198237 bytes_retransmit=0 bytes_invalid=0 send_seq=10263 receive_seq=10263 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998649 coil_temp=17.0 refs=0 mcu_temp=20.10 supply_voltage=3.012 th0: temp=55.0 th1: temp=54.0 th2: temp=59.6 th3: temp=57.2 sysload=0.74 cputime=411.221 memavail=7393816 print_time=5561.315 buffer_time=1.196 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5538.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26179994 bytes_read=4001336 bytes_retransmit=9 bytes_invalid=0 send_seq=490201 receive_seq=490201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016341 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34396 bytes_read=107930 bytes_retransmit=0 bytes_invalid=0 send_seq=5704 receive_seq=5704 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997252 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170012 bytes_read=5307845 bytes_retransmit=9 bytes_invalid=0 send_seq=23468 receive_seq=23468 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997640 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=112232 bytes_read=2861492 bytes_retransmit=9 bytes_invalid=0 send_seq=15306 receive_seq=15306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997499 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34663 bytes_read=1413253 bytes_retransmit=9 bytes_invalid=0 send_seq=5718 receive_seq=5718 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35149 bytes_read=105814 bytes_retransmit=9 bytes_invalid=0 send_seq=5705 receive_seq=5705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89241 bytes_read=2198593 bytes_retransmit=0 bytes_invalid=0 send_seq=10264 receive_seq=10264 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998670 coil_temp=17.0 refs=0 mcu_temp=20.10 supply_voltage=3.012 th0: temp=55.1 th1: temp=54.2 th2: temp=59.6 th3: temp=57.3 sysload=0.74 cputime=411.302 memavail=7393816 print_time=5561.315 buffer_time=0.195 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
LIS2DW finished 'toolboard_t1' measurements
Resonances data written to /tmp/resonances_y_250.000_250.000_20.000_t1.csv file
Stats 5539.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26180292 bytes_read=4001757 bytes_retransmit=9 bytes_invalid=0 send_seq=490224 receive_seq=490224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016312 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34402 bytes_read=107946 bytes_retransmit=0 bytes_invalid=0 send_seq=5705 receive_seq=5705 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997304 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170018 bytes_read=5307945 bytes_retransmit=9 bytes_invalid=0 send_seq=23469 receive_seq=23469 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997714 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=112314 bytes_read=2862674 bytes_retransmit=9 bytes_invalid=0 send_seq=15316 receive_seq=15316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34669 bytes_read=1413517 bytes_retransmit=9 bytes_invalid=0 send_seq=5719 receive_seq=5719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997700 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35155 bytes_read=105830 bytes_retransmit=9 bytes_invalid=0 send_seq=5706 receive_seq=5706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89247 bytes_read=2198949 bytes_retransmit=0 bytes_invalid=0 send_seq=10265 receive_seq=10265 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998701 coil_temp=16.9 refs=0 mcu_temp=20.10 supply_voltage=3.012 th0: temp=54.9 th1: temp=54.1 th2: temp=59.5 th3: temp=57.3 sysload=0.74 cputime=411.415 memavail=7395236 print_time=5567.055 buffer_time=4.935 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5540.5: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26180590 bytes_read=4002181 bytes_retransmit=9 bytes_invalid=0 send_seq=490247 receive_seq=490247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016291 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34408 bytes_read=107962 bytes_retransmit=0 bytes_invalid=0 send_seq=5706 receive_seq=5706 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997235 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170024 bytes_read=5308045 bytes_retransmit=9 bytes_invalid=0 send_seq=23470 receive_seq=23470 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997631 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=112320 bytes_read=2862774 bytes_retransmit=9 bytes_invalid=0 send_seq=15317 receive_seq=15317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997469 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34675 bytes_read=1413751 bytes_retransmit=9 bytes_invalid=0 send_seq=5720 receive_seq=5720 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35161 bytes_read=105846 bytes_retransmit=9 bytes_invalid=0 send_seq=5707 receive_seq=5707 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89253 bytes_read=2199305 bytes_retransmit=0 bytes_invalid=0 send_seq=10266 receive_seq=10266 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998647 coil_temp=16.9 refs=0 mcu_temp=20.10 supply_voltage=3.012 th0: temp=55.2 th1: temp=54.1 th2: temp=59.7 th3: temp=57.1 sysload=0.68 cputime=411.458 memavail=7395236 print_time=5567.055 buffer_time=3.935 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5541.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26180888 bytes_read=4002651 bytes_retransmit=9 bytes_invalid=0 send_seq=490270 receive_seq=490270 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016251 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34414 bytes_read=107978 bytes_retransmit=0 bytes_invalid=0 send_seq=5707 receive_seq=5707 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997245 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170030 bytes_read=5308187 bytes_retransmit=9 bytes_invalid=0 send_seq=23471 receive_seq=23471 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997650 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=112326 bytes_read=2862902 bytes_retransmit=9 bytes_invalid=0 send_seq=15318 receive_seq=15318 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997497 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34681 bytes_read=1414015 bytes_retransmit=9 bytes_invalid=0 send_seq=5721 receive_seq=5721 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999565 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35167 bytes_read=105862 bytes_retransmit=9 bytes_invalid=0 send_seq=5708 receive_seq=5708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89259 bytes_read=2199661 bytes_retransmit=0 bytes_invalid=0 send_seq=10267 receive_seq=10267 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998652 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=55.4 th1: temp=54.1 th2: temp=59.7 th3: temp=57.3 sysload=0.68 cputime=411.503 memavail=7396504 print_time=5567.055 buffer_time=2.934 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Running Command {generate_shaper_graphs}...:
please wait...

Stats 5542.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26181186 bytes_read=4003076 bytes_retransmit=9 bytes_invalid=0 send_seq=490293 receive_seq=490293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016209 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34420 bytes_read=108007 bytes_retransmit=0 bytes_invalid=0 send_seq=5708 receive_seq=5708 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997283 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170036 bytes_read=5308287 bytes_retransmit=9 bytes_invalid=0 send_seq=23472 receive_seq=23472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997687 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=112332 bytes_read=2863002 bytes_retransmit=9 bytes_invalid=0 send_seq=15319 receive_seq=15319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34687 bytes_read=1414279 bytes_retransmit=9 bytes_invalid=0 send_seq=5722 receive_seq=5722 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35173 bytes_read=105889 bytes_retransmit=9 bytes_invalid=0 send_seq=5709 receive_seq=5709 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89265 bytes_read=2200017 bytes_retransmit=0 bytes_invalid=0 send_seq=10268 receive_seq=10268 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998673 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=55.4 th1: temp=54.1 th2: temp=59.7 th3: temp=57.4 sysload=0.68 cputime=411.560 memavail=7394092 print_time=5567.055 buffer_time=1.933 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5543.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26181454 bytes_read=4003471 bytes_retransmit=9 bytes_invalid=0 send_seq=490310 receive_seq=490310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016165 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34426 bytes_read=108023 bytes_retransmit=0 bytes_invalid=0 send_seq=5709 receive_seq=5709 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997313 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170042 bytes_read=5308387 bytes_retransmit=9 bytes_invalid=0 send_seq=23473 receive_seq=23473 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997727 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=112338 bytes_read=2863102 bytes_retransmit=9 bytes_invalid=0 send_seq=15320 receive_seq=15320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997566 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34693 bytes_read=1414528 bytes_retransmit=9 bytes_invalid=0 send_seq=5723 receive_seq=5723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999581 adj=47997706 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35179 bytes_read=105905 bytes_retransmit=9 bytes_invalid=0 send_seq=5710 receive_seq=5710 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89271 bytes_read=2200373 bytes_retransmit=0 bytes_invalid=0 send_seq=10269 receive_seq=10269 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998689 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=55.5 th1: temp=54.0 th2: temp=59.7 th3: temp=57.3 sysload=0.68 cputime=411.617 memavail=7382008 print_time=5567.055 buffer_time=0.933 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5544.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26181752 bytes_read=4003925 bytes_retransmit=9 bytes_invalid=0 send_seq=490333 receive_seq=490333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016132 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34432 bytes_read=108039 bytes_retransmit=0 bytes_invalid=0 send_seq=5710 receive_seq=5710 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997347 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170048 bytes_read=5308515 bytes_retransmit=9 bytes_invalid=0 send_seq=23474 receive_seq=23474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997767 toolboard_t1: mcu_awake=0.019 mcu_task_avg=0.000063 mcu_task_stddev=0.000070 bytes_write=112344 bytes_read=2863245 bytes_retransmit=9 bytes_invalid=0 send_seq=15321 receive_seq=15321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997616 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34699 bytes_read=1414792 bytes_retransmit=9 bytes_invalid=0 send_seq=5724 receive_seq=5724 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999579 adj=47997841 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35185 bytes_read=105921 bytes_retransmit=9 bytes_invalid=0 send_seq=5711 receive_seq=5711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89277 bytes_read=2200729 bytes_retransmit=0 bytes_invalid=0 send_seq=10270 receive_seq=10270 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998748 coil_temp=17.0 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=55.8 th1: temp=54.1 th2: temp=59.6 th3: temp=57.3 sysload=0.68 cputime=411.671 memavail=7381508 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5545.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26182050 bytes_read=4004350 bytes_retransmit=9 bytes_invalid=0 send_seq=490356 receive_seq=490356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016101 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34438 bytes_read=108055 bytes_retransmit=0 bytes_invalid=0 send_seq=5711 receive_seq=5711 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997381 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170054 bytes_read=5308615 bytes_retransmit=9 bytes_invalid=0 send_seq=23475 receive_seq=23475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997795 toolboard_t1: mcu_awake=0.019 mcu_task_avg=0.000063 mcu_task_stddev=0.000070 bytes_write=112350 bytes_read=2863345 bytes_retransmit=9 bytes_invalid=0 send_seq=15322 receive_seq=15322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997640 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34705 bytes_read=1415056 bytes_retransmit=9 bytes_invalid=0 send_seq=5725 receive_seq=5725 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999578 adj=47997852 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35191 bytes_read=105937 bytes_retransmit=9 bytes_invalid=0 send_seq=5712 receive_seq=5712 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999466 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89283 bytes_read=2201085 bytes_retransmit=0 bytes_invalid=0 send_seq=10271 receive_seq=10271 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998761 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=55.7 th1: temp=54.2 th2: temp=59.6 th3: temp=57.2 sysload=0.71 cputime=411.723 memavail=7381492 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5546.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000007 bytes_write=26182343 bytes_read=4004785 bytes_retransmit=9 bytes_invalid=0 send_seq=490378 receive_seq=490378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016078 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34444 bytes_read=108071 bytes_retransmit=0 bytes_invalid=0 send_seq=5712 receive_seq=5712 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997411 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170060 bytes_read=5308725 bytes_retransmit=9 bytes_invalid=0 send_seq=23476 receive_seq=23476 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997824 toolboard_t1: mcu_awake=0.019 mcu_task_avg=0.000063 mcu_task_stddev=0.000070 bytes_write=112356 bytes_read=2863441 bytes_retransmit=9 bytes_invalid=0 send_seq=15323 receive_seq=15323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997671 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34711 bytes_read=1415290 bytes_retransmit=9 bytes_invalid=0 send_seq=5726 receive_seq=5726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999576 adj=47997865 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35197 bytes_read=105953 bytes_retransmit=9 bytes_invalid=0 send_seq=5713 receive_seq=5713 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999471 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89289 bytes_read=2201441 bytes_retransmit=0 bytes_invalid=0 send_seq=10272 receive_seq=10272 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998783 coil_temp=16.9 refs=0 mcu_temp=20.14 supply_voltage=3.012 th0: temp=55.9 th1: temp=54.3 th2: temp=59.6 th3: temp=57.3 sysload=0.71 cputime=411.776 memavail=7380232 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5547.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000007 bytes_write=26182636 bytes_read=4005234 bytes_retransmit=9 bytes_invalid=0 send_seq=490400 receive_seq=490400 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016057 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34450 bytes_read=108100 bytes_retransmit=0 bytes_invalid=0 send_seq=5713 receive_seq=5713 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997426 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170066 bytes_read=5308844 bytes_retransmit=9 bytes_invalid=0 send_seq=23477 receive_seq=23477 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997845 toolboard_t1: mcu_awake=0.019 mcu_task_avg=0.000063 mcu_task_stddev=0.000070 bytes_write=112362 bytes_read=2863560 bytes_retransmit=9 bytes_invalid=0 send_seq=15324 receive_seq=15324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997690 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34717 bytes_read=1415554 bytes_retransmit=9 bytes_invalid=0 send_seq=5727 receive_seq=5727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999574 adj=47997868 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35203 bytes_read=105980 bytes_retransmit=9 bytes_invalid=0 send_seq=5714 receive_seq=5714 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999476 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89295 bytes_read=2201797 bytes_retransmit=0 bytes_invalid=0 send_seq=10273 receive_seq=10273 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998798 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=55.9 th1: temp=54.3 th2: temp=59.6 th3: temp=57.2 sysload=0.71 cputime=411.834 memavail=7381348 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5548.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000007 bytes_write=26182934 bytes_read=4005659 bytes_retransmit=9 bytes_invalid=0 send_seq=490423 receive_seq=490423 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016029 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34456 bytes_read=108116 bytes_retransmit=0 bytes_invalid=0 send_seq=5714 receive_seq=5714 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997460 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170072 bytes_read=5308937 bytes_retransmit=9 bytes_invalid=0 send_seq=23478 receive_seq=23478 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997873 toolboard_t1: mcu_awake=0.019 mcu_task_avg=0.000063 mcu_task_stddev=0.000070 bytes_write=112368 bytes_read=2863653 bytes_retransmit=9 bytes_invalid=0 send_seq=15325 receive_seq=15325 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997715 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34723 bytes_read=1415833 bytes_retransmit=9 bytes_invalid=0 send_seq=5728 receive_seq=5728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999576 adj=47997879 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35209 bytes_read=105996 bytes_retransmit=9 bytes_invalid=0 send_seq=5715 receive_seq=5715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999483 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89301 bytes_read=2202153 bytes_retransmit=0 bytes_invalid=0 send_seq=10274 receive_seq=10274 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998803 coil_temp=17.0 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=56.0 th1: temp=54.2 th2: temp=59.8 th3: temp=57.3 sysload=0.71 cputime=411.885 memavail=7381348 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5549.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000007 bytes_write=26183232 bytes_read=4006084 bytes_retransmit=9 bytes_invalid=0 send_seq=490446 receive_seq=490446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016001 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34462 bytes_read=108132 bytes_retransmit=0 bytes_invalid=0 send_seq=5715 receive_seq=5715 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997491 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170078 bytes_read=5309030 bytes_retransmit=9 bytes_invalid=0 send_seq=23479 receive_seq=23479 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997907 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=112374 bytes_read=2863760 bytes_retransmit=9 bytes_invalid=0 send_seq=15326 receive_seq=15326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997763 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34729 bytes_read=1416067 bytes_retransmit=9 bytes_invalid=0 send_seq=5729 receive_seq=5729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999581 adj=47997921 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35215 bytes_read=106012 bytes_retransmit=9 bytes_invalid=0 send_seq=5716 receive_seq=5716 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999495 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89307 bytes_read=2202509 bytes_retransmit=0 bytes_invalid=0 send_seq=10275 receive_seq=10275 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999947 adj=31998815 coil_temp=17.0 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=56.1 th1: temp=54.5 th2: temp=59.7 th3: temp=57.1 sysload=0.71 cputime=411.936 memavail=7381348 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5550.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000007 bytes_write=26183530 bytes_read=4006534 bytes_retransmit=9 bytes_invalid=0 send_seq=490469 receive_seq=490469 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015981 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34468 bytes_read=108148 bytes_retransmit=0 bytes_invalid=0 send_seq=5716 receive_seq=5716 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997521 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170084 bytes_read=5309153 bytes_retransmit=9 bytes_invalid=0 send_seq=23480 receive_seq=23480 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997943 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=112380 bytes_read=2863883 bytes_retransmit=9 bytes_invalid=0 send_seq=15327 receive_seq=15327 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997793 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34735 bytes_read=1416331 bytes_retransmit=9 bytes_invalid=0 send_seq=5730 receive_seq=5730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999579 adj=47997994 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35221 bytes_read=106028 bytes_retransmit=9 bytes_invalid=0 send_seq=5717 receive_seq=5717 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999501 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89313 bytes_read=2202865 bytes_retransmit=0 bytes_invalid=0 send_seq=10276 receive_seq=10276 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998867 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=56.2 th1: temp=54.4 th2: temp=59.7 th3: temp=57.1 sysload=0.73 cputime=411.988 memavail=7381356 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5551.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26183828 bytes_read=4006974 bytes_retransmit=9 bytes_invalid=0 send_seq=490492 receive_seq=490492 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015958 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34474 bytes_read=108164 bytes_retransmit=0 bytes_invalid=0 send_seq=5717 receive_seq=5717 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997546 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170090 bytes_read=5309267 bytes_retransmit=9 bytes_invalid=0 send_seq=23481 receive_seq=23481 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997974 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=112386 bytes_read=2863983 bytes_retransmit=9 bytes_invalid=0 send_seq=15328 receive_seq=15328 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997830 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34741 bytes_read=1416595 bytes_retransmit=9 bytes_invalid=0 send_seq=5731 receive_seq=5731 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999581 adj=47997995 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35227 bytes_read=106044 bytes_retransmit=9 bytes_invalid=0 send_seq=5718 receive_seq=5718 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999507 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89319 bytes_read=2203221 bytes_retransmit=0 bytes_invalid=0 send_seq=10277 receive_seq=10277 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998873 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=56.6 th1: temp=54.5 th2: temp=59.6 th3: temp=57.2 sysload=0.73 cputime=412.047 memavail=7371784 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5552.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26184126 bytes_read=4007399 bytes_retransmit=9 bytes_invalid=0 send_seq=490515 receive_seq=490515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015947 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34480 bytes_read=108193 bytes_retransmit=0 bytes_invalid=0 send_seq=5718 receive_seq=5718 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997583 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170096 bytes_read=5309367 bytes_retransmit=9 bytes_invalid=0 send_seq=23482 receive_seq=23482 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63998016 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=112392 bytes_read=2864083 bytes_retransmit=9 bytes_invalid=0 send_seq=15329 receive_seq=15329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997857 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34747 bytes_read=1416829 bytes_retransmit=9 bytes_invalid=0 send_seq=5732 receive_seq=5732 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999578 adj=47998054 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35233 bytes_read=106071 bytes_retransmit=9 bytes_invalid=0 send_seq=5719 receive_seq=5719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999513 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89325 bytes_read=2203577 bytes_retransmit=0 bytes_invalid=0 send_seq=10278 receive_seq=10278 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998880 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=56.3 th1: temp=54.6 th2: temp=59.7 th3: temp=57.2 sysload=0.73 cputime=412.104 memavail=7367500 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Fitted shaper 'zv' frequency = 55.2 Hz (vibrations = 1.5%, smoothing ~= 0.057)
To avoid too much smoothing with 'zv', suggested max_accel <= 11900 mm/sec^2
Fitted shaper 'mzv' frequency = 54.2 Hz (vibrations = 0.0%, smoothing ~= 0.069)
To avoid too much smoothing with 'mzv', suggested max_accel <= 8700 mm/sec^2
Fitted shaper 'ei' frequency = 66.8 Hz (vibrations = 0.0%, smoothing ~= 0.072)
To avoid too much smoothing with 'ei', suggested max_accel <= 8300 mm/sec^2
Fitted shaper '2hump_ei' frequency = 85.2 Hz (vibrations = 0.0%, smoothing ~= 0.074)
To avoid too much smoothing with '2hump_ei', suggested max_accel <= 8100 mm/sec^2
Fitted shaper '3hump_ei' frequency = 102.0 Hz (vibrations = 0.0%, smoothing ~= 0.079)
To avoid too much smoothing with '3hump_ei', suggested max_accel <= 7600 mm/sec^2
Recommended shaper is mzv @ 54.2 Hz

please wait...

Stats 5553.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26184424 bytes_read=4007853 bytes_retransmit=9 bytes_invalid=0 send_seq=490538 receive_seq=490538 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015925 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34486 bytes_read=108209 bytes_retransmit=0 bytes_invalid=0 send_seq=5719 receive_seq=5719 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997611 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170102 bytes_read=5309495 bytes_retransmit=9 bytes_invalid=0 send_seq=23483 receive_seq=23483 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63998045 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=112398 bytes_read=2864211 bytes_retransmit=9 bytes_invalid=0 send_seq=15330 receive_seq=15330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997866 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34753 bytes_read=1417123 bytes_retransmit=9 bytes_invalid=0 send_seq=5733 receive_seq=5733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999577 adj=47998043 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35239 bytes_read=106087 bytes_retransmit=9 bytes_invalid=0 send_seq=5720 receive_seq=5720 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999517 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89331 bytes_read=2203933 bytes_retransmit=0 bytes_invalid=0 send_seq=10279 receive_seq=10279 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998883 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=56.5 th1: temp=54.5 th2: temp=59.6 th3: temp=57.3 sysload=0.73 cputime=412.173 memavail=7380676 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5554.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26184722 bytes_read=4008278 bytes_retransmit=9 bytes_invalid=0 send_seq=490561 receive_seq=490561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015906 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34492 bytes_read=108225 bytes_retransmit=0 bytes_invalid=0 send_seq=5720 receive_seq=5720 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997595 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170108 bytes_read=5309595 bytes_retransmit=9 bytes_invalid=0 send_seq=23484 receive_seq=23484 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63998044 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112404 bytes_read=2864325 bytes_retransmit=9 bytes_invalid=0 send_seq=15331 receive_seq=15331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997847 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34759 bytes_read=1417372 bytes_retransmit=9 bytes_invalid=0 send_seq=5734 receive_seq=5734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999575 adj=47997986 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35245 bytes_read=106103 bytes_retransmit=9 bytes_invalid=0 send_seq=5721 receive_seq=5721 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999515 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89337 bytes_read=2204289 bytes_retransmit=0 bytes_invalid=0 send_seq=10280 receive_seq=10280 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998863 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=56.7 th1: temp=54.5 th2: temp=59.6 th3: temp=57.2 sysload=0.73 cputime=412.225 memavail=7380676 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5555.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26185015 bytes_read=4008698 bytes_retransmit=9 bytes_invalid=0 send_seq=490583 receive_seq=490583 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015889 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34498 bytes_read=108241 bytes_retransmit=0 bytes_invalid=0 send_seq=5721 receive_seq=5721 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997548 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170114 bytes_read=5309695 bytes_retransmit=9 bytes_invalid=0 send_seq=23485 receive_seq=23485 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997999 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112410 bytes_read=2864425 bytes_retransmit=9 bytes_invalid=0 send_seq=15332 receive_seq=15332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997799 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34765 bytes_read=1417606 bytes_retransmit=9 bytes_invalid=0 send_seq=5735 receive_seq=5735 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999582 adj=47997909 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35251 bytes_read=106119 bytes_retransmit=9 bytes_invalid=0 send_seq=5722 receive_seq=5722 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999518 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89343 bytes_read=2204645 bytes_retransmit=0 bytes_invalid=0 send_seq=10281 receive_seq=10281 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998855 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=56.5 th1: temp=54.7 th2: temp=59.6 th3: temp=57.2 sysload=0.75 cputime=412.276 memavail=7380676 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5556.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26185313 bytes_read=4009167 bytes_retransmit=9 bytes_invalid=0 send_seq=490606 receive_seq=490606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015871 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34504 bytes_read=108257 bytes_retransmit=0 bytes_invalid=0 send_seq=5722 receive_seq=5722 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997508 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170120 bytes_read=5309837 bytes_retransmit=9 bytes_invalid=0 send_seq=23486 receive_seq=23486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997960 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112416 bytes_read=2864553 bytes_retransmit=9 bytes_invalid=0 send_seq=15333 receive_seq=15333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997772 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34771 bytes_read=1417885 bytes_retransmit=9 bytes_invalid=0 send_seq=5736 receive_seq=5736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999581 adj=47998000 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35257 bytes_read=106135 bytes_retransmit=9 bytes_invalid=0 send_seq=5723 receive_seq=5723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999504 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89349 bytes_read=2205001 bytes_retransmit=0 bytes_invalid=0 send_seq=10282 receive_seq=10282 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998817 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=56.7 th1: temp=54.8 th2: temp=59.7 th3: temp=57.4 sysload=0.75 cputime=412.329 memavail=7379192 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5557.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26185606 bytes_read=4009587 bytes_retransmit=9 bytes_invalid=0 send_seq=490628 receive_seq=490628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015866 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=34510 bytes_read=108286 bytes_retransmit=0 bytes_invalid=0 send_seq=5723 receive_seq=5723 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997479 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170126 bytes_read=5309937 bytes_retransmit=9 bytes_invalid=0 send_seq=23487 receive_seq=23487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997927 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112422 bytes_read=2864653 bytes_retransmit=9 bytes_invalid=0 send_seq=15334 receive_seq=15334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997739 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34777 bytes_read=1418134 bytes_retransmit=9 bytes_invalid=0 send_seq=5737 receive_seq=5737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999579 adj=47997933 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35263 bytes_read=106162 bytes_retransmit=9 bytes_invalid=0 send_seq=5724 receive_seq=5724 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999498 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89355 bytes_read=2205357 bytes_retransmit=0 bytes_invalid=0 send_seq=10283 receive_seq=10283 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998796 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=56.6 th1: temp=54.6 th2: temp=59.5 th3: temp=57.2 sysload=0.75 cputime=412.380 memavail=7379192 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5558.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26185910 bytes_read=4010028 bytes_retransmit=9 bytes_invalid=0 send_seq=490652 receive_seq=490652 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015838 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=34522 bytes_read=108318 bytes_retransmit=0 bytes_invalid=0 send_seq=5725 receive_seq=5725 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997434 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170138 bytes_read=5310053 bytes_retransmit=9 bytes_invalid=0 send_seq=23489 receive_seq=23489 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997876 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112434 bytes_read=2864769 bytes_retransmit=9 bytes_invalid=0 send_seq=15336 receive_seq=15336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997681 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34789 bytes_read=1418399 bytes_retransmit=9 bytes_invalid=0 send_seq=5739 receive_seq=5739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999574 adj=47997845 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35275 bytes_read=106194 bytes_retransmit=9 bytes_invalid=0 send_seq=5726 receive_seq=5726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999484 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89367 bytes_read=2205729 bytes_retransmit=0 bytes_invalid=0 send_seq=10285 receive_seq=10285 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998758 coil_temp=16.9 refs=0 mcu_temp=20.10 supply_voltage=3.012 th0: temp=56.6 th1: temp=54.2 th2: temp=59.6 th3: temp=57.3 sysload=0.75 cputime=412.432 memavail=7379192 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5559.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26186208 bytes_read=4010482 bytes_retransmit=9 bytes_invalid=0 send_seq=490675 receive_seq=490675 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015823 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=34528 bytes_read=108334 bytes_retransmit=0 bytes_invalid=0 send_seq=5726 receive_seq=5726 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997449 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170144 bytes_read=5310181 bytes_retransmit=9 bytes_invalid=0 send_seq=23490 receive_seq=23490 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997896 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112440 bytes_read=2864911 bytes_retransmit=9 bytes_invalid=0 send_seq=15337 receive_seq=15337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997699 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34795 bytes_read=1418678 bytes_retransmit=9 bytes_invalid=0 send_seq=5740 receive_seq=5740 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999573 adj=47997785 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35281 bytes_read=106210 bytes_retransmit=9 bytes_invalid=0 send_seq=5727 receive_seq=5727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999483 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89373 bytes_read=2206085 bytes_retransmit=0 bytes_invalid=0 send_seq=10286 receive_seq=10286 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998756 coil_temp=16.9 refs=0 mcu_temp=20.10 supply_voltage=3.012 th0: temp=56.9 th1: temp=54.6 th2: temp=59.9 th3: temp=57.2 sysload=0.75 cputime=412.485 memavail=7379192 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5560.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26186501 bytes_read=4010902 bytes_retransmit=9 bytes_invalid=0 send_seq=490697 receive_seq=490697 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015813 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=34534 bytes_read=108350 bytes_retransmit=0 bytes_invalid=0 send_seq=5727 receive_seq=5727 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997417 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170150 bytes_read=5310281 bytes_retransmit=9 bytes_invalid=0 send_seq=23491 receive_seq=23491 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997871 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112446 bytes_read=2865011 bytes_retransmit=9 bytes_invalid=0 send_seq=15338 receive_seq=15338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997674 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34801 bytes_read=1418927 bytes_retransmit=9 bytes_invalid=0 send_seq=5741 receive_seq=5741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999579 adj=47997758 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35287 bytes_read=106226 bytes_retransmit=9 bytes_invalid=0 send_seq=5728 receive_seq=5728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999477 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89379 bytes_read=2206441 bytes_retransmit=0 bytes_invalid=0 send_seq=10287 receive_seq=10287 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998751 coil_temp=16.9 refs=0 mcu_temp=20.10 supply_voltage=3.012 th0: temp=57.0 th1: temp=54.6 th2: temp=59.7 th3: temp=57.2 sysload=0.77 cputime=412.536 memavail=7379192 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5561.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26186799 bytes_read=4011338 bytes_retransmit=9 bytes_invalid=0 send_seq=490720 receive_seq=490720 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015807 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=34540 bytes_read=108366 bytes_retransmit=0 bytes_invalid=0 send_seq=5728 receive_seq=5728 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997401 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170156 bytes_read=5310395 bytes_retransmit=9 bytes_invalid=0 send_seq=23492 receive_seq=23492 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997850 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112452 bytes_read=2865111 bytes_retransmit=9 bytes_invalid=0 send_seq=15339 receive_seq=15339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997686 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34807 bytes_read=1419161 bytes_retransmit=9 bytes_invalid=0 send_seq=5742 receive_seq=5742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999577 adj=47997856 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35293 bytes_read=106242 bytes_retransmit=9 bytes_invalid=0 send_seq=5729 receive_seq=5729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999471 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89385 bytes_read=2206797 bytes_retransmit=0 bytes_invalid=0 send_seq=10288 receive_seq=10288 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998741 coil_temp=16.9 refs=0 mcu_temp=20.09 supply_voltage=3.012 th0: temp=57.1 th1: temp=54.5 th2: temp=59.7 th3: temp=57.2 sysload=0.77 cputime=412.597 memavail=7372148 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5562.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26187097 bytes_read=4011792 bytes_retransmit=9 bytes_invalid=0 send_seq=490743 receive_seq=490743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015798 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34546 bytes_read=108395 bytes_retransmit=0 bytes_invalid=0 send_seq=5729 receive_seq=5729 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997381 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170162 bytes_read=5310523 bytes_retransmit=9 bytes_invalid=0 send_seq=23493 receive_seq=23493 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997848 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112458 bytes_read=2865239 bytes_retransmit=9 bytes_invalid=0 send_seq=15340 receive_seq=15340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997679 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34813 bytes_read=1419440 bytes_retransmit=9 bytes_invalid=0 send_seq=5743 receive_seq=5743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999575 adj=47997791 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35299 bytes_read=106269 bytes_retransmit=9 bytes_invalid=0 send_seq=5730 receive_seq=5730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999467 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89391 bytes_read=2207153 bytes_retransmit=0 bytes_invalid=0 send_seq=10289 receive_seq=10289 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998729 coil_temp=16.9 refs=0 mcu_temp=20.09 supply_voltage=3.012 th0: temp=57.0 th1: temp=54.5 th2: temp=59.6 th3: temp=57.0 sysload=0.77 cputime=412.660 memavail=7368888 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Fitted shaper 'zv' frequency = 55.0 Hz (vibrations = 2.3%, smoothing ~= 0.057)
To avoid too much smoothing with 'zv', suggested max_accel <= 11800 mm/sec^2
Fitted shaper 'mzv' frequency = 53.2 Hz (vibrations = 0.0%, smoothing ~= 0.072)
To avoid too much smoothing with 'mzv', suggested max_accel <= 8300 mm/sec^2
Fitted shaper 'ei' frequency = 65.2 Hz (vibrations = 0.0%, smoothing ~= 0.076)
To avoid too much smoothing with 'ei', suggested max_accel <= 7900 mm/sec^2
Fitted shaper '2hump_ei' frequency = 83.0 Hz (vibrations = 0.0%, smoothing ~= 0.078)
To avoid too much smoothing with '2hump_ei', suggested max_accel <= 7700 mm/sec^2
Fitted shaper '3hump_ei' frequency = 101.8 Hz (vibrations = 0.0%, smoothing ~= 0.079)
To avoid too much smoothing with '3hump_ei', suggested max_accel <= 7600 mm/sec^2
Recommended shaper is mzv @ 53.2 Hz

Command {generate_shaper_graphs} finished

Running Command {generate_shaper_graphs}...:
please wait...

Stats 5563.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26187390 bytes_read=4012212 bytes_retransmit=9 bytes_invalid=0 send_seq=490765 receive_seq=490765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015790 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34552 bytes_read=108411 bytes_retransmit=0 bytes_invalid=0 send_seq=5730 receive_seq=5730 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997371 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170168 bytes_read=5310623 bytes_retransmit=9 bytes_invalid=0 send_seq=23494 receive_seq=23494 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997835 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112464 bytes_read=2865339 bytes_retransmit=9 bytes_invalid=0 send_seq=15341 receive_seq=15341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997662 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34819 bytes_read=1419704 bytes_retransmit=9 bytes_invalid=0 send_seq=5744 receive_seq=5744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999573 adj=47997745 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35305 bytes_read=106285 bytes_retransmit=9 bytes_invalid=0 send_seq=5731 receive_seq=5731 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89397 bytes_read=2207509 bytes_retransmit=0 bytes_invalid=0 send_seq=10290 receive_seq=10290 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999951 adj=31998801 coil_temp=16.9 refs=0 mcu_temp=20.09 supply_voltage=3.012 th0: temp=57.3 th1: temp=54.5 th2: temp=59.7 th3: temp=57.1 sysload=0.77 cputime=412.746 memavail=7380292 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5564.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26187688 bytes_read=4012637 bytes_retransmit=9 bytes_invalid=0 send_seq=490788 receive_seq=490788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015788 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34558 bytes_read=108427 bytes_retransmit=0 bytes_invalid=0 send_seq=5731 receive_seq=5731 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997389 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170174 bytes_read=5310723 bytes_retransmit=9 bytes_invalid=0 send_seq=23495 receive_seq=23495 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997827 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112470 bytes_read=2865453 bytes_retransmit=9 bytes_invalid=0 send_seq=15342 receive_seq=15342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997648 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34825 bytes_read=1419938 bytes_retransmit=9 bytes_invalid=0 send_seq=5745 receive_seq=5745 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999571 adj=47997721 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35311 bytes_read=106301 bytes_retransmit=9 bytes_invalid=0 send_seq=5732 receive_seq=5732 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89403 bytes_read=2207865 bytes_retransmit=0 bytes_invalid=0 send_seq=10291 receive_seq=10291 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999951 adj=31998872 coil_temp=16.9 refs=0 mcu_temp=20.10 supply_voltage=3.012 th0: temp=57.1 th1: temp=54.8 th2: temp=59.8 th3: temp=57.2 sysload=0.77 cputime=412.803 memavail=7380912 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 5565.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26187976 bytes_read=4013081 bytes_retransmit=9 bytes_invalid=0 send_seq=490809 receive_seq=490809 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015783 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34564 bytes_read=108443 bytes_retransmit=0 bytes_invalid=0 send_seq=5732 receive_seq=5732 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997364 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170180 bytes_read=5310851 bytes_retransmit=9 bytes_invalid=0 send_seq=23496 receive_seq=23496 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997794 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112476 bytes_read=2865581 bytes_retransmit=9 bytes_invalid=0 send_seq=15343 receive_seq=15343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997643 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34831 bytes_read=1420232 bytes_retransmit=9 bytes_invalid=0 send_seq=5746 receive_seq=5746 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999573 adj=47997682 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35317 bytes_read=106317 bytes_retransmit=9 bytes_invalid=0 send_seq=5733 receive_seq=5733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89409 bytes_read=2208239 bytes_retransmit=0 bytes_invalid=0 send_seq=10292 receive_seq=10292 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999949 adj=31998817 coil_temp=16.9 refs=0 mcu_temp=20.10 supply_voltage=3.012 th0: temp=57.2 th1: temp=54.7 th2: temp=59.5 th3: temp=57.2 sysload=1.03 cputime=412.872 memavail=7379672 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5566.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26188274 bytes_read=4013521 bytes_retransmit=9 bytes_invalid=0 send_seq=490832 receive_seq=490832 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015777 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34570 bytes_read=108459 bytes_retransmit=0 bytes_invalid=0 send_seq=5733 receive_seq=5733 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997355 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170186 bytes_read=5310965 bytes_retransmit=9 bytes_invalid=0 send_seq=23497 receive_seq=23497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997782 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112482 bytes_read=2865681 bytes_retransmit=9 bytes_invalid=0 send_seq=15344 receive_seq=15344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997618 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34837 bytes_read=1420466 bytes_retransmit=9 bytes_invalid=0 send_seq=5747 receive_seq=5747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999571 adj=47997714 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35323 bytes_read=106344 bytes_retransmit=9 bytes_invalid=0 send_seq=5734 receive_seq=5734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=31.6  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89415 bytes_read=2208595 bytes_retransmit=0 bytes_invalid=0 send_seq=10293 receive_seq=10293 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999949 adj=31998765 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=57.0 th1: temp=54.6 th2: temp=59.7 th3: temp=57.2 sysload=1.03 cputime=413.009 memavail=7377696 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5567.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26188572 bytes_read=4013946 bytes_retransmit=9 bytes_invalid=0 send_seq=490855 receive_seq=490855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015771 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34576 bytes_read=108488 bytes_retransmit=0 bytes_invalid=0 send_seq=5734 receive_seq=5734 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997358 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170192 bytes_read=5311065 bytes_retransmit=9 bytes_invalid=0 send_seq=23498 receive_seq=23498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997768 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112488 bytes_read=2865781 bytes_retransmit=9 bytes_invalid=0 send_seq=15345 receive_seq=15345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997613 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34843 bytes_read=1420700 bytes_retransmit=9 bytes_invalid=0 send_seq=5748 receive_seq=5748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999569 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35329 bytes_read=106360 bytes_retransmit=9 bytes_invalid=0 send_seq=5735 receive_seq=5735 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=31.6  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89421 bytes_read=2208951 bytes_retransmit=0 bytes_invalid=0 send_seq=10294 receive_seq=10294 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999949 adj=31998746 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=57.3 th1: temp=54.7 th2: temp=59.7 th3: temp=57.2 sysload=1.03 cputime=413.091 memavail=7379372 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5568.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26188870 bytes_read=4014400 bytes_retransmit=9 bytes_invalid=0 send_seq=490878 receive_seq=490878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015758 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34582 bytes_read=108504 bytes_retransmit=0 bytes_invalid=0 send_seq=5735 receive_seq=5735 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997360 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170198 bytes_read=5311193 bytes_retransmit=9 bytes_invalid=0 send_seq=23499 receive_seq=23499 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997767 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112494 bytes_read=2865909 bytes_retransmit=9 bytes_invalid=0 send_seq=15346 receive_seq=15346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997602 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34849 bytes_read=1421009 bytes_retransmit=9 bytes_invalid=0 send_seq=5749 receive_seq=5749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999567 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35335 bytes_read=106376 bytes_retransmit=9 bytes_invalid=0 send_seq=5736 receive_seq=5736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89427 bytes_read=2209307 bytes_retransmit=0 bytes_invalid=0 send_seq=10295 receive_seq=10295 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999948 adj=31998746 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=57.3 th1: temp=54.6 th2: temp=59.6 th3: temp=57.1 sysload=1.03 cputime=413.144 memavail=7378868 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5569.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26189168 bytes_read=4014825 bytes_retransmit=9 bytes_invalid=0 send_seq=490901 receive_seq=490901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015760 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34588 bytes_read=108520 bytes_retransmit=0 bytes_invalid=0 send_seq=5736 receive_seq=5736 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997358 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170204 bytes_read=5311293 bytes_retransmit=9 bytes_invalid=0 send_seq=23500 receive_seq=23500 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997780 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112500 bytes_read=2866023 bytes_retransmit=9 bytes_invalid=0 send_seq=15347 receive_seq=15347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997748 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34855 bytes_read=1421243 bytes_retransmit=9 bytes_invalid=0 send_seq=5750 receive_seq=5750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999569 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35341 bytes_read=106392 bytes_retransmit=9 bytes_invalid=0 send_seq=5737 receive_seq=5737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89433 bytes_read=2209663 bytes_retransmit=0 bytes_invalid=0 send_seq=10296 receive_seq=10296 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999948 adj=31998735 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=57.3 th1: temp=54.7 th2: temp=59.8 th3: temp=57.2 sysload=1.03 cputime=413.195 memavail=7378880 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5570.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26189466 bytes_read=4015264 bytes_retransmit=9 bytes_invalid=0 send_seq=490924 receive_seq=490924 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015758 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34594 bytes_read=108536 bytes_retransmit=0 bytes_invalid=0 send_seq=5737 receive_seq=5737 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997329 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170210 bytes_read=5311393 bytes_retransmit=9 bytes_invalid=0 send_seq=23501 receive_seq=23501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997750 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112506 bytes_read=2866123 bytes_retransmit=9 bytes_invalid=0 send_seq=15348 receive_seq=15348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997672 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34861 bytes_read=1421477 bytes_retransmit=9 bytes_invalid=0 send_seq=5751 receive_seq=5751 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999567 adj=47997692 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35347 bytes_read=106408 bytes_retransmit=9 bytes_invalid=0 send_seq=5738 receive_seq=5738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89439 bytes_read=2210019 bytes_retransmit=0 bytes_invalid=0 send_seq=10297 receive_seq=10297 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999947 adj=31998709 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=57.0 th1: temp=54.6 th2: temp=59.6 th3: temp=57.2 sysload=1.03 cputime=413.246 memavail=7378628 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5571.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26189764 bytes_read=4015715 bytes_retransmit=9 bytes_invalid=0 send_seq=490947 receive_seq=490947 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015756 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34600 bytes_read=108552 bytes_retransmit=0 bytes_invalid=0 send_seq=5738 receive_seq=5738 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997320 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170216 bytes_read=5311535 bytes_retransmit=9 bytes_invalid=0 send_seq=23502 receive_seq=23502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997744 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112512 bytes_read=2866251 bytes_retransmit=9 bytes_invalid=0 send_seq=15349 receive_seq=15349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997631 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34867 bytes_read=1421771 bytes_retransmit=9 bytes_invalid=0 send_seq=5752 receive_seq=5752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999565 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35353 bytes_read=106435 bytes_retransmit=9 bytes_invalid=0 send_seq=5739 receive_seq=5739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89445 bytes_read=2210375 bytes_retransmit=0 bytes_invalid=0 send_seq=10298 receive_seq=10298 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998693 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=57.4 th1: temp=54.6 th2: temp=59.7 th3: temp=57.1 sysload=1.03 cputime=413.302 memavail=7375128 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5572.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26190062 bytes_read=4016138 bytes_retransmit=9 bytes_invalid=0 send_seq=490970 receive_seq=490970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015758 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=34606 bytes_read=108581 bytes_retransmit=0 bytes_invalid=0 send_seq=5739 receive_seq=5739 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997312 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170222 bytes_read=5311635 bytes_retransmit=9 bytes_invalid=0 send_seq=23503 receive_seq=23503 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997753 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112518 bytes_read=2866351 bytes_retransmit=9 bytes_invalid=0 send_seq=15350 receive_seq=15350 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997601 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34873 bytes_read=1422005 bytes_retransmit=9 bytes_invalid=0 send_seq=5753 receive_seq=5753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35359 bytes_read=106451 bytes_retransmit=9 bytes_invalid=0 send_seq=5740 receive_seq=5740 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89451 bytes_read=2210731 bytes_retransmit=0 bytes_invalid=0 send_seq=10299 receive_seq=10299 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998682 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=57.3 th1: temp=54.6 th2: temp=59.8 th3: temp=57.1 sysload=1.03 cputime=413.362 memavail=7366828 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Fitted shaper 'zv' frequency = 55.2 Hz (vibrations = 25.7%, smoothing ~= 0.057)
To avoid too much smoothing with 'zv', suggested max_accel <= 11900 mm/sec^2
Fitted shaper 'mzv' frequency = 40.8 Hz (vibrations = 8.3%, smoothing ~= 0.122)
To avoid too much smoothing with 'mzv', suggested max_accel <= 4900 mm/sec^2
Fitted shaper 'ei' frequency = 49.4 Hz (vibrations = 6.6%, smoothing ~= 0.132)
To avoid too much smoothing with 'ei', suggested max_accel <= 4500 mm/sec^2
Fitted shaper '2hump_ei' frequency = 45.0 Hz (vibrations = 2.2%, smoothing ~= 0.266)
To avoid too much smoothing with '2hump_ei', suggested max_accel <= 2200 mm/sec^2
Fitted shaper '3hump_ei' frequency = 49.2 Hz (vibrations = 1.2%, smoothing ~= 0.339)
To avoid too much smoothing with '3hump_ei', suggested max_accel <= 1600 mm/sec^2
Recommended shaper is 2hump_ei @ 45.0 Hz

please wait...

Stats 5573.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26190350 bytes_read=4016582 bytes_retransmit=9 bytes_invalid=0 send_seq=490991 receive_seq=490991 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015748 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=34612 bytes_read=108597 bytes_retransmit=0 bytes_invalid=0 send_seq=5740 receive_seq=5740 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997298 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170228 bytes_read=5311735 bytes_retransmit=9 bytes_invalid=0 send_seq=23504 receive_seq=23504 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997738 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112524 bytes_read=2866451 bytes_retransmit=9 bytes_invalid=0 send_seq=15351 receive_seq=15351 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997581 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34879 bytes_read=1422254 bytes_retransmit=9 bytes_invalid=0 send_seq=5754 receive_seq=5754 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35365 bytes_read=106467 bytes_retransmit=9 bytes_invalid=0 send_seq=5741 receive_seq=5741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89457 bytes_read=2211087 bytes_retransmit=0 bytes_invalid=0 send_seq=10300 receive_seq=10300 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998677 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=57.5 th1: temp=54.6 th2: temp=59.6 th3: temp=57.4 sysload=1.03 cputime=413.425 memavail=7382792 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5574.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26190648 bytes_read=4017007 bytes_retransmit=9 bytes_invalid=0 send_seq=491014 receive_seq=491014 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015747 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=34618 bytes_read=108613 bytes_retransmit=0 bytes_invalid=0 send_seq=5741 receive_seq=5741 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997306 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170234 bytes_read=5311863 bytes_retransmit=9 bytes_invalid=0 send_seq=23505 receive_seq=23505 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997750 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112530 bytes_read=2866593 bytes_retransmit=9 bytes_invalid=0 send_seq=15352 receive_seq=15352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997617 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34885 bytes_read=1422548 bytes_retransmit=9 bytes_invalid=0 send_seq=5755 receive_seq=5755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997632 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35371 bytes_read=106483 bytes_retransmit=9 bytes_invalid=0 send_seq=5742 receive_seq=5742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89463 bytes_read=2211443 bytes_retransmit=0 bytes_invalid=0 send_seq=10301 receive_seq=10301 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999956 adj=31998692 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=57.5 th1: temp=54.6 th2: temp=59.7 th3: temp=57.2 sysload=1.03 cputime=413.480 memavail=7379796 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 5575.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26190946 bytes_read=4017432 bytes_retransmit=9 bytes_invalid=0 send_seq=491037 receive_seq=491037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015745 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=34624 bytes_read=108629 bytes_retransmit=0 bytes_invalid=0 send_seq=5742 receive_seq=5742 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997300 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170240 bytes_read=5311963 bytes_retransmit=9 bytes_invalid=0 send_seq=23506 receive_seq=23506 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997744 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112536 bytes_read=2866693 bytes_retransmit=9 bytes_invalid=0 send_seq=15353 receive_seq=15353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997583 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34891 bytes_read=1422782 bytes_retransmit=9 bytes_invalid=0 send_seq=5756 receive_seq=5756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35377 bytes_read=106499 bytes_retransmit=9 bytes_invalid=0 send_seq=5743 receive_seq=5743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89469 bytes_read=2211799 bytes_retransmit=0 bytes_invalid=0 send_seq=10302 receive_seq=10302 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999954 adj=31998847 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=57.5 th1: temp=54.8 th2: temp=59.8 th3: temp=57.1 sysload=1.11 cputime=413.531 memavail=7379544 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5576.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26191244 bytes_read=4017901 bytes_retransmit=9 bytes_invalid=0 send_seq=491060 receive_seq=491060 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015745 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=34630 bytes_read=108645 bytes_retransmit=0 bytes_invalid=0 send_seq=5743 receive_seq=5743 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997295 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170246 bytes_read=5312091 bytes_retransmit=9 bytes_invalid=0 send_seq=23507 receive_seq=23507 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997731 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112542 bytes_read=2866793 bytes_retransmit=9 bytes_invalid=0 send_seq=15354 receive_seq=15354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997559 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34897 bytes_read=1423016 bytes_retransmit=9 bytes_invalid=0 send_seq=5757 receive_seq=5757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35383 bytes_read=106526 bytes_retransmit=9 bytes_invalid=0 send_seq=5744 receive_seq=5744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89475 bytes_read=2212155 bytes_retransmit=0 bytes_invalid=0 send_seq=10303 receive_seq=10303 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999952 adj=31998780 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=57.6 th1: temp=55.0 th2: temp=59.8 th3: temp=57.3 sysload=1.11 cputime=413.583 memavail=7379300 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5577.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26191537 bytes_read=4018321 bytes_retransmit=9 bytes_invalid=0 send_seq=491082 receive_seq=491082 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015764 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=34636 bytes_read=108674 bytes_retransmit=0 bytes_invalid=0 send_seq=5744 receive_seq=5744 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997291 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170252 bytes_read=5312205 bytes_retransmit=9 bytes_invalid=0 send_seq=23508 receive_seq=23508 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997723 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112548 bytes_read=2866921 bytes_retransmit=9 bytes_invalid=0 send_seq=15355 receive_seq=15355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34903 bytes_read=1423310 bytes_retransmit=9 bytes_invalid=0 send_seq=5758 receive_seq=5758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997626 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35389 bytes_read=106542 bytes_retransmit=9 bytes_invalid=0 send_seq=5745 receive_seq=5745 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89481 bytes_read=2212511 bytes_retransmit=0 bytes_invalid=0 send_seq=10304 receive_seq=10304 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999953 adj=31998732 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=57.4 th1: temp=54.8 th2: temp=59.4 th3: temp=57.3 sysload=1.11 cputime=413.636 memavail=7378572 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5578.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26191830 bytes_read=4018741 bytes_retransmit=9 bytes_invalid=0 send_seq=491104 receive_seq=491104 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015762 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=34642 bytes_read=108690 bytes_retransmit=0 bytes_invalid=0 send_seq=5745 receive_seq=5745 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997239 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170258 bytes_read=5312305 bytes_retransmit=9 bytes_invalid=0 send_seq=23509 receive_seq=23509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997671 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112554 bytes_read=2867021 bytes_retransmit=9 bytes_invalid=0 send_seq=15356 receive_seq=15356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34909 bytes_read=1423559 bytes_retransmit=9 bytes_invalid=0 send_seq=5759 receive_seq=5759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997581 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35395 bytes_read=106558 bytes_retransmit=9 bytes_invalid=0 send_seq=5746 receive_seq=5746 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89487 bytes_read=2212867 bytes_retransmit=0 bytes_invalid=0 send_seq=10305 receive_seq=10305 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999952 adj=31998711 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=57.5 th1: temp=55.0 th2: temp=59.7 th3: temp=57.2 sysload=1.11 cputime=413.686 memavail=7378572 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5579.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26192128 bytes_read=4019195 bytes_retransmit=9 bytes_invalid=0 send_seq=491127 receive_seq=491127 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015762 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=34648 bytes_read=108706 bytes_retransmit=0 bytes_invalid=0 send_seq=5746 receive_seq=5746 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997241 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170264 bytes_read=5312419 bytes_retransmit=9 bytes_invalid=0 send_seq=23510 receive_seq=23510 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997699 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112560 bytes_read=2867135 bytes_retransmit=9 bytes_invalid=0 send_seq=15357 receive_seq=15357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997502 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34915 bytes_read=1423793 bytes_retransmit=9 bytes_invalid=0 send_seq=5760 receive_seq=5760 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997600 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35401 bytes_read=106574 bytes_retransmit=9 bytes_invalid=0 send_seq=5747 receive_seq=5747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89493 bytes_read=2213223 bytes_retransmit=0 bytes_invalid=0 send_seq=10306 receive_seq=10306 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999951 adj=31998692 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=57.5 th1: temp=54.6 th2: temp=59.7 th3: temp=57.2 sysload=1.11 cputime=413.738 memavail=7378352 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5580.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26192426 bytes_read=4019620 bytes_retransmit=9 bytes_invalid=0 send_seq=491150 receive_seq=491150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015760 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=34654 bytes_read=108722 bytes_retransmit=0 bytes_invalid=0 send_seq=5747 receive_seq=5747 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997246 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170270 bytes_read=5312533 bytes_retransmit=9 bytes_invalid=0 send_seq=23511 receive_seq=23511 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997716 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112566 bytes_read=2867263 bytes_retransmit=9 bytes_invalid=0 send_seq=15358 receive_seq=15358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997495 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34921 bytes_read=1424087 bytes_retransmit=9 bytes_invalid=0 send_seq=5761 receive_seq=5761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997601 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35407 bytes_read=106590 bytes_retransmit=9 bytes_invalid=0 send_seq=5748 receive_seq=5748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89499 bytes_read=2213579 bytes_retransmit=0 bytes_invalid=0 send_seq=10307 receive_seq=10307 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999950 adj=31998685 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=57.5 th1: temp=54.6 th2: temp=59.6 th3: temp=57.1 sysload=1.10 cputime=413.790 memavail=7378352 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5581.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26192724 bytes_read=4020060 bytes_retransmit=9 bytes_invalid=0 send_seq=491173 receive_seq=491173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015764 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=34660 bytes_read=108738 bytes_retransmit=0 bytes_invalid=0 send_seq=5748 receive_seq=5748 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997252 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170276 bytes_read=5312633 bytes_retransmit=9 bytes_invalid=0 send_seq=23512 receive_seq=23512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997715 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112572 bytes_read=2867363 bytes_retransmit=9 bytes_invalid=0 send_seq=15359 receive_seq=15359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997495 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34927 bytes_read=1424321 bytes_retransmit=9 bytes_invalid=0 send_seq=5762 receive_seq=5762 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997607 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35413 bytes_read=106617 bytes_retransmit=9 bytes_invalid=0 send_seq=5749 receive_seq=5749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=31.6  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89505 bytes_read=2213935 bytes_retransmit=0 bytes_invalid=0 send_seq=10308 receive_seq=10308 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999948 adj=31998669 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=57.8 th1: temp=54.8 th2: temp=59.6 th3: temp=57.2 sysload=1.10 cputime=413.844 memavail=7371804 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5582.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26193022 bytes_read=4020510 bytes_retransmit=9 bytes_invalid=0 send_seq=491196 receive_seq=491196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015769 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34666 bytes_read=108767 bytes_retransmit=0 bytes_invalid=0 send_seq=5749 receive_seq=5749 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997250 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170282 bytes_read=5312761 bytes_retransmit=9 bytes_invalid=0 send_seq=23513 receive_seq=23513 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997724 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112578 bytes_read=2867477 bytes_retransmit=9 bytes_invalid=0 send_seq=15360 receive_seq=15360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997484 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34933 bytes_read=1424555 bytes_retransmit=9 bytes_invalid=0 send_seq=5763 receive_seq=5763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35419 bytes_read=106633 bytes_retransmit=9 bytes_invalid=0 send_seq=5750 receive_seq=5750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89511 bytes_read=2214291 bytes_retransmit=0 bytes_invalid=0 send_seq=10309 receive_seq=10309 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999947 adj=31998645 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=57.6 th1: temp=54.7 th2: temp=59.7 th3: temp=57.2 sysload=1.10 cputime=413.904 memavail=7367888 print_time=5567.055 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Fitted shaper 'zv' frequency = 57.0 Hz (vibrations = 32.3%, smoothing ~= 0.054)
To avoid too much smoothing with 'zv', suggested max_accel <= 12700 mm/sec^2
Fitted shaper 'mzv' frequency = 47.6 Hz (vibrations = 13.1%, smoothing ~= 0.090)
To avoid too much smoothing with 'mzv', suggested max_accel <= 6700 mm/sec^2
Fitted shaper 'ei' frequency = 56.2 Hz (vibrations = 13.3%, smoothing ~= 0.102)
To avoid too much smoothing with 'ei', suggested max_accel <= 5900 mm/sec^2
Fitted shaper '2hump_ei' frequency = 58.4 Hz (vibrations = 6.7%, smoothing ~= 0.158)
To avoid too much smoothing with '2hump_ei', suggested max_accel <= 3800 mm/sec^2
Fitted shaper '3hump_ei' frequency = 57.0 Hz (vibrations = 4.2%, smoothing ~= 0.252)
To avoid too much smoothing with '3hump_ei', suggested max_accel <= 2300 mm/sec^2
Recommended shaper is mzv @ 47.6 Hz

Command {generate_shaper_graphs} finished

toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 5583.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26194080 bytes_read=4020995 bytes_retransmit=9 bytes_invalid=0 send_seq=491231 receive_seq=491231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015769 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34672 bytes_read=108783 bytes_retransmit=0 bytes_invalid=0 send_seq=5750 receive_seq=5750 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997241 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170288 bytes_read=5312875 bytes_retransmit=9 bytes_invalid=0 send_seq=23514 receive_seq=23514 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997729 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112584 bytes_read=2867591 bytes_retransmit=9 bytes_invalid=0 send_seq=15361 receive_seq=15361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34939 bytes_read=1424864 bytes_retransmit=9 bytes_invalid=0 send_seq=5764 receive_seq=5764 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997629 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35425 bytes_read=106649 bytes_retransmit=9 bytes_invalid=0 send_seq=5751 receive_seq=5751 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89517 bytes_read=2214647 bytes_retransmit=0 bytes_invalid=0 send_seq=10310 receive_seq=10310 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998626 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=57.6 th1: temp=54.9 th2: temp=59.6 th3: temp=57.2 sysload=1.10 cputime=414.033 memavail=7391672 print_time=5606.757 buffer_time=0.575 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Activating extruder extruder
Extruder 'extruder' now syncing with 'extruder'
Extruder 'extruder1' now syncing with 'extruder1'
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 5584.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26194471 bytes_read=4021430 bytes_retransmit=9 bytes_invalid=0 send_seq=491256 receive_seq=491256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015770 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34678 bytes_read=108799 bytes_retransmit=0 bytes_invalid=0 send_seq=5751 receive_seq=5751 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997258 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170294 bytes_read=5312975 bytes_retransmit=9 bytes_invalid=0 send_seq=23515 receive_seq=23515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997711 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112590 bytes_read=2867705 bytes_retransmit=9 bytes_invalid=0 send_seq=15362 receive_seq=15362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997487 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34945 bytes_read=1425098 bytes_retransmit=9 bytes_invalid=0 send_seq=5765 receive_seq=5765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997632 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35431 bytes_read=106665 bytes_retransmit=9 bytes_invalid=0 send_seq=5752 receive_seq=5752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89523 bytes_read=2215003 bytes_retransmit=0 bytes_invalid=0 send_seq=10311 receive_seq=10311 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998641 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=57.5 th1: temp=54.7 th2: temp=59.7 th3: temp=57.2 sysload=1.10 cputime=414.118 memavail=7391652 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5585.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26194769 bytes_read=4021884 bytes_retransmit=9 bytes_invalid=0 send_seq=491279 receive_seq=491279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015769 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34684 bytes_read=108815 bytes_retransmit=0 bytes_invalid=0 send_seq=5752 receive_seq=5752 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997243 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170300 bytes_read=5313089 bytes_retransmit=9 bytes_invalid=0 send_seq=23516 receive_seq=23516 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997701 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112596 bytes_read=2867819 bytes_retransmit=9 bytes_invalid=0 send_seq=15363 receive_seq=15363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34951 bytes_read=1425332 bytes_retransmit=9 bytes_invalid=0 send_seq=5766 receive_seq=5766 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35437 bytes_read=106681 bytes_retransmit=9 bytes_invalid=0 send_seq=5753 receive_seq=5753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89529 bytes_read=2215359 bytes_retransmit=0 bytes_invalid=0 send_seq=10312 receive_seq=10312 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998634 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=57.3 th1: temp=54.5 th2: temp=59.5 th3: temp=57.2 sysload=1.01 cputime=414.163 memavail=7394028 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5586.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26195067 bytes_read=4022324 bytes_retransmit=9 bytes_invalid=0 send_seq=491302 receive_seq=491302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015767 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34690 bytes_read=108831 bytes_retransmit=0 bytes_invalid=0 send_seq=5753 receive_seq=5753 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997248 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170306 bytes_read=5313203 bytes_retransmit=9 bytes_invalid=0 send_seq=23517 receive_seq=23517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997696 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112602 bytes_read=2867933 bytes_retransmit=9 bytes_invalid=0 send_seq=15364 receive_seq=15364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997512 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34957 bytes_read=1425626 bytes_retransmit=9 bytes_invalid=0 send_seq=5767 receive_seq=5767 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35443 bytes_read=106708 bytes_retransmit=9 bytes_invalid=0 send_seq=5754 receive_seq=5754 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89535 bytes_read=2215715 bytes_retransmit=0 bytes_invalid=0 send_seq=10313 receive_seq=10313 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998632 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=57.2 th1: temp=54.4 th2: temp=59.7 th3: temp=57.1 sysload=1.01 cputime=414.209 memavail=7394028 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5587.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26195365 bytes_read=4022749 bytes_retransmit=9 bytes_invalid=0 send_seq=491325 receive_seq=491325 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015771 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34696 bytes_read=108860 bytes_retransmit=0 bytes_invalid=0 send_seq=5754 receive_seq=5754 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997246 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170312 bytes_read=5313317 bytes_retransmit=9 bytes_invalid=0 send_seq=23518 receive_seq=23518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997702 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112608 bytes_read=2868033 bytes_retransmit=9 bytes_invalid=0 send_seq=15365 receive_seq=15365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997517 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=34963 bytes_read=1425860 bytes_retransmit=9 bytes_invalid=0 send_seq=5768 receive_seq=5768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999566 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35449 bytes_read=106724 bytes_retransmit=9 bytes_invalid=0 send_seq=5755 receive_seq=5755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89541 bytes_read=2216071 bytes_retransmit=0 bytes_invalid=0 send_seq=10314 receive_seq=10314 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998629 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=57.0 th1: temp=54.5 th2: temp=59.6 th3: temp=57.0 sysload=1.01 cputime=414.255 memavail=7392536 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5588.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26195663 bytes_read=4023203 bytes_retransmit=9 bytes_invalid=0 send_seq=491348 receive_seq=491348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015776 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34702 bytes_read=108876 bytes_retransmit=0 bytes_invalid=0 send_seq=5755 receive_seq=5755 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997237 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170318 bytes_read=5313431 bytes_retransmit=9 bytes_invalid=0 send_seq=23519 receive_seq=23519 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997684 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112614 bytes_read=2868147 bytes_retransmit=9 bytes_invalid=0 send_seq=15366 receive_seq=15366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997502 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34969 bytes_read=1426109 bytes_retransmit=9 bytes_invalid=0 send_seq=5769 receive_seq=5769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999565 adj=47997810 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35455 bytes_read=106740 bytes_retransmit=9 bytes_invalid=0 send_seq=5756 receive_seq=5756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89547 bytes_read=2216427 bytes_retransmit=0 bytes_invalid=0 send_seq=10315 receive_seq=10315 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998619 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=56.9 th1: temp=54.2 th2: temp=59.7 th3: temp=57.1 sysload=1.01 cputime=414.300 memavail=7392536 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5589.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26195961 bytes_read=4023628 bytes_retransmit=9 bytes_invalid=0 send_seq=491371 receive_seq=491371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015774 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34708 bytes_read=108892 bytes_retransmit=0 bytes_invalid=0 send_seq=5756 receive_seq=5756 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997224 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170324 bytes_read=5313545 bytes_retransmit=9 bytes_invalid=0 send_seq=23520 receive_seq=23520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997673 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112620 bytes_read=2868275 bytes_retransmit=9 bytes_invalid=0 send_seq=15367 receive_seq=15367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997489 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34975 bytes_read=1426403 bytes_retransmit=9 bytes_invalid=0 send_seq=5770 receive_seq=5770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997746 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35461 bytes_read=106756 bytes_retransmit=9 bytes_invalid=0 send_seq=5757 receive_seq=5757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89553 bytes_read=2216783 bytes_retransmit=0 bytes_invalid=0 send_seq=10316 receive_seq=10316 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998612 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=56.7 th1: temp=54.0 th2: temp=59.8 th3: temp=57.2 sysload=1.01 cputime=414.347 memavail=7391676 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5590.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26196259 bytes_read=4024053 bytes_retransmit=9 bytes_invalid=0 send_seq=491394 receive_seq=491394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015769 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34714 bytes_read=108908 bytes_retransmit=0 bytes_invalid=0 send_seq=5757 receive_seq=5757 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997229 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170330 bytes_read=5313645 bytes_retransmit=9 bytes_invalid=0 send_seq=23521 receive_seq=23521 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997688 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112626 bytes_read=2868375 bytes_retransmit=9 bytes_invalid=0 send_seq=15368 receive_seq=15368 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997513 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34981 bytes_read=1426637 bytes_retransmit=9 bytes_invalid=0 send_seq=5771 receive_seq=5771 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997713 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35467 bytes_read=106772 bytes_retransmit=9 bytes_invalid=0 send_seq=5758 receive_seq=5758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89559 bytes_read=2217139 bytes_retransmit=0 bytes_invalid=0 send_seq=10317 receive_seq=10317 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998617 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=56.5 th1: temp=54.0 th2: temp=59.6 th3: temp=57.2 sysload=0.93 cputime=414.392 memavail=7391676 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5591.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26196557 bytes_read=4024522 bytes_retransmit=9 bytes_invalid=0 send_seq=491417 receive_seq=491417 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015767 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=34720 bytes_read=108924 bytes_retransmit=0 bytes_invalid=0 send_seq=5758 receive_seq=5758 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997231 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170336 bytes_read=5313759 bytes_retransmit=9 bytes_invalid=0 send_seq=23522 receive_seq=23522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997696 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112632 bytes_read=2868489 bytes_retransmit=9 bytes_invalid=0 send_seq=15369 receive_seq=15369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34987 bytes_read=1426871 bytes_retransmit=9 bytes_invalid=0 send_seq=5772 receive_seq=5772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999569 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35473 bytes_read=106799 bytes_retransmit=9 bytes_invalid=0 send_seq=5759 receive_seq=5759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89565 bytes_read=2217495 bytes_retransmit=0 bytes_invalid=0 send_seq=10318 receive_seq=10318 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998626 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=56.6 th1: temp=53.9 th2: temp=59.8 th3: temp=57.2 sysload=0.93 cputime=414.437 memavail=7391676 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5592.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26196855 bytes_read=4024947 bytes_retransmit=9 bytes_invalid=0 send_seq=491440 receive_seq=491440 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015761 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=34726 bytes_read=108952 bytes_retransmit=0 bytes_invalid=0 send_seq=5759 receive_seq=5759 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997243 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170342 bytes_read=5313887 bytes_retransmit=9 bytes_invalid=0 send_seq=23523 receive_seq=23523 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997696 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112638 bytes_read=2868603 bytes_retransmit=9 bytes_invalid=0 send_seq=15370 receive_seq=15370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997537 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=34993 bytes_read=1427165 bytes_retransmit=9 bytes_invalid=0 send_seq=5773 receive_seq=5773 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999569 adj=47997791 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35479 bytes_read=106815 bytes_retransmit=9 bytes_invalid=0 send_seq=5760 receive_seq=5760 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89571 bytes_read=2217851 bytes_retransmit=0 bytes_invalid=0 send_seq=10319 receive_seq=10319 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998655 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=56.0 th1: temp=53.6 th2: temp=59.6 th3: temp=57.1 sysload=0.93 cputime=414.482 memavail=7391676 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5593.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26197153 bytes_read=4025367 bytes_retransmit=9 bytes_invalid=0 send_seq=491463 receive_seq=491463 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015763 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=34732 bytes_read=108967 bytes_retransmit=0 bytes_invalid=0 send_seq=5760 receive_seq=5760 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997274 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170348 bytes_read=5313987 bytes_retransmit=9 bytes_invalid=0 send_seq=23524 receive_seq=23524 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997713 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112644 bytes_read=2868703 bytes_retransmit=9 bytes_invalid=0 send_seq=15371 receive_seq=15371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997817 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=34999 bytes_read=1427414 bytes_retransmit=9 bytes_invalid=0 send_seq=5774 receive_seq=5774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999567 adj=47997764 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35485 bytes_read=106831 bytes_retransmit=9 bytes_invalid=0 send_seq=5761 receive_seq=5761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89577 bytes_read=2218207 bytes_retransmit=0 bytes_invalid=0 send_seq=10320 receive_seq=10320 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998673 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=56.0 th1: temp=53.5 th2: temp=59.5 th3: temp=57.2 sysload=0.93 cputime=414.526 memavail=7391676 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5594.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26197451 bytes_read=4025821 bytes_retransmit=9 bytes_invalid=0 send_seq=491486 receive_seq=491486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015760 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=34738 bytes_read=108982 bytes_retransmit=0 bytes_invalid=0 send_seq=5761 receive_seq=5761 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997284 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170354 bytes_read=5314101 bytes_retransmit=9 bytes_invalid=0 send_seq=23525 receive_seq=23525 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997706 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=112650 bytes_read=2868831 bytes_retransmit=9 bytes_invalid=0 send_seq=15372 receive_seq=15372 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997733 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35005 bytes_read=1427648 bytes_retransmit=9 bytes_invalid=0 send_seq=5775 receive_seq=5775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999566 adj=47997720 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35491 bytes_read=106847 bytes_retransmit=9 bytes_invalid=0 send_seq=5762 receive_seq=5762 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89583 bytes_read=2218556 bytes_retransmit=0 bytes_invalid=0 send_seq=10321 receive_seq=10321 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998672 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=55.8 th1: temp=53.6 th2: temp=59.6 th3: temp=57.1 sysload=0.93 cputime=414.571 memavail=7391676 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5595.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26197749 bytes_read=4026246 bytes_retransmit=9 bytes_invalid=0 send_seq=491509 receive_seq=491509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015761 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=34744 bytes_read=108997 bytes_retransmit=0 bytes_invalid=0 send_seq=5762 receive_seq=5762 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997295 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170360 bytes_read=5314215 bytes_retransmit=9 bytes_invalid=0 send_seq=23526 receive_seq=23526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997753 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=112656 bytes_read=2868945 bytes_retransmit=9 bytes_invalid=0 send_seq=15373 receive_seq=15373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997673 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35011 bytes_read=1427942 bytes_retransmit=9 bytes_invalid=0 send_seq=5776 receive_seq=5776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35497 bytes_read=106863 bytes_retransmit=9 bytes_invalid=0 send_seq=5763 receive_seq=5763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89589 bytes_read=2218901 bytes_retransmit=0 bytes_invalid=0 send_seq=10322 receive_seq=10322 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998705 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=55.6 th1: temp=53.4 th2: temp=59.7 th3: temp=57.2 sysload=0.85 cputime=414.618 memavail=7391676 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5596.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26198047 bytes_read=4026686 bytes_retransmit=9 bytes_invalid=0 send_seq=491532 receive_seq=491532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015759 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000007 bytes_write=34750 bytes_read=109012 bytes_retransmit=0 bytes_invalid=0 send_seq=5763 receive_seq=5763 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997298 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170366 bytes_read=5314315 bytes_retransmit=9 bytes_invalid=0 send_seq=23527 receive_seq=23527 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997736 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=112662 bytes_read=2869045 bytes_retransmit=9 bytes_invalid=0 send_seq=15374 receive_seq=15374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997619 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35017 bytes_read=1428176 bytes_retransmit=9 bytes_invalid=0 send_seq=5777 receive_seq=5777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35503 bytes_read=106890 bytes_retransmit=9 bytes_invalid=0 send_seq=5764 receive_seq=5764 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89595 bytes_read=2219245 bytes_retransmit=0 bytes_invalid=0 send_seq=10323 receive_seq=10323 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998689 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=55.7 th1: temp=53.4 th2: temp=59.8 th3: temp=57.2 sysload=0.85 cputime=414.663 memavail=7391696 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5597.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26198345 bytes_read=4027140 bytes_retransmit=9 bytes_invalid=0 send_seq=491555 receive_seq=491555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015776 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=34756 bytes_read=109041 bytes_retransmit=0 bytes_invalid=0 send_seq=5764 receive_seq=5764 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997303 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170372 bytes_read=5314443 bytes_retransmit=9 bytes_invalid=0 send_seq=23528 receive_seq=23528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997750 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=112668 bytes_read=2869159 bytes_retransmit=9 bytes_invalid=0 send_seq=15375 receive_seq=15375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997586 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35023 bytes_read=1428410 bytes_retransmit=9 bytes_invalid=0 send_seq=5778 receive_seq=5778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35509 bytes_read=106906 bytes_retransmit=9 bytes_invalid=0 send_seq=5765 receive_seq=5765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89601 bytes_read=2219590 bytes_retransmit=0 bytes_invalid=0 send_seq=10324 receive_seq=10324 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998682 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=55.3 th1: temp=53.2 th2: temp=59.6 th3: temp=57.1 sysload=0.85 cputime=414.711 memavail=7391712 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5598.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26198643 bytes_read=4027565 bytes_retransmit=9 bytes_invalid=0 send_seq=491578 receive_seq=491578 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015890 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=34762 bytes_read=109057 bytes_retransmit=0 bytes_invalid=0 send_seq=5765 receive_seq=5765 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997284 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170378 bytes_read=5314557 bytes_retransmit=9 bytes_invalid=0 send_seq=23529 receive_seq=23529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997705 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=112674 bytes_read=2869273 bytes_retransmit=9 bytes_invalid=0 send_seq=15376 receive_seq=15376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997535 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35029 bytes_read=1428719 bytes_retransmit=9 bytes_invalid=0 send_seq=5779 receive_seq=5779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35515 bytes_read=106922 bytes_retransmit=9 bytes_invalid=0 send_seq=5766 receive_seq=5766 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89607 bytes_read=2219935 bytes_retransmit=0 bytes_invalid=0 send_seq=10325 receive_seq=10325 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998647 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=55.2 th1: temp=53.0 th2: temp=59.5 th3: temp=57.3 sysload=0.85 cputime=414.759 memavail=7385164 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5599.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26198941 bytes_read=4027990 bytes_retransmit=9 bytes_invalid=0 send_seq=491601 receive_seq=491601 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015891 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=34768 bytes_read=109073 bytes_retransmit=0 bytes_invalid=0 send_seq=5766 receive_seq=5766 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997047 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170384 bytes_read=5314657 bytes_retransmit=9 bytes_invalid=0 send_seq=23530 receive_seq=23530 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997415 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112680 bytes_read=2869387 bytes_retransmit=9 bytes_invalid=0 send_seq=15377 receive_seq=15377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997236 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35035 bytes_read=1428953 bytes_retransmit=9 bytes_invalid=0 send_seq=5780 receive_seq=5780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997412 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35521 bytes_read=106938 bytes_retransmit=9 bytes_invalid=0 send_seq=5767 receive_seq=5767 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999387 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89613 bytes_read=2220280 bytes_retransmit=0 bytes_invalid=0 send_seq=10326 receive_seq=10326 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998509 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=55.0 th1: temp=52.9 th2: temp=59.8 th3: temp=57.1 sysload=0.85 cputime=414.805 memavail=7391304 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5600.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26199239 bytes_read=4028444 bytes_retransmit=9 bytes_invalid=0 send_seq=491624 receive_seq=491624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015892 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=34774 bytes_read=109089 bytes_retransmit=0 bytes_invalid=0 send_seq=5767 receive_seq=5767 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997093 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170390 bytes_read=5314785 bytes_retransmit=9 bytes_invalid=0 send_seq=23531 receive_seq=23531 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997491 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112686 bytes_read=2869501 bytes_retransmit=9 bytes_invalid=0 send_seq=15378 receive_seq=15378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997293 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35041 bytes_read=1429187 bytes_retransmit=9 bytes_invalid=0 send_seq=5781 receive_seq=5781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997453 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35527 bytes_read=106954 bytes_retransmit=9 bytes_invalid=0 send_seq=5768 receive_seq=5768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999399 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89619 bytes_read=2220625 bytes_retransmit=0 bytes_invalid=0 send_seq=10327 receive_seq=10327 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998542 coil_temp=16.9 refs=0 mcu_temp=20.10 supply_voltage=3.012 th0: temp=55.1 th1: temp=52.9 th2: temp=59.7 th3: temp=57.0 sysload=0.79 cputime=414.849 memavail=7391056 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5601.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26199537 bytes_read=4028884 bytes_retransmit=9 bytes_invalid=0 send_seq=491647 receive_seq=491647 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015886 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=34780 bytes_read=109105 bytes_retransmit=0 bytes_invalid=0 send_seq=5768 receive_seq=5768 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997126 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170396 bytes_read=5314885 bytes_retransmit=9 bytes_invalid=0 send_seq=23532 receive_seq=23532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997530 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112692 bytes_read=2869615 bytes_retransmit=9 bytes_invalid=0 send_seq=15379 receive_seq=15379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997340 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35047 bytes_read=1429481 bytes_retransmit=9 bytes_invalid=0 send_seq=5782 receive_seq=5782 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997484 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35533 bytes_read=106981 bytes_retransmit=9 bytes_invalid=0 send_seq=5769 receive_seq=5769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999408 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89625 bytes_read=2220970 bytes_retransmit=0 bytes_invalid=0 send_seq=10328 receive_seq=10328 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998565 coil_temp=16.9 refs=0 mcu_temp=20.10 supply_voltage=3.012 th0: temp=54.7 th1: temp=52.7 th2: temp=59.7 th3: temp=57.1 sysload=0.79 cputime=414.893 memavail=7391056 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5602.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26199835 bytes_read=4029309 bytes_retransmit=9 bytes_invalid=0 send_seq=491670 receive_seq=491670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015881 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34786 bytes_read=109134 bytes_retransmit=0 bytes_invalid=0 send_seq=5769 receive_seq=5769 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997158 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170402 bytes_read=5314999 bytes_retransmit=9 bytes_invalid=0 send_seq=23533 receive_seq=23533 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997577 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112698 bytes_read=2869715 bytes_retransmit=9 bytes_invalid=0 send_seq=15380 receive_seq=15380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997407 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35053 bytes_read=1429715 bytes_retransmit=9 bytes_invalid=0 send_seq=5783 receive_seq=5783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997520 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35539 bytes_read=106997 bytes_retransmit=9 bytes_invalid=0 send_seq=5770 receive_seq=5770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999422 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89631 bytes_read=2221318 bytes_retransmit=0 bytes_invalid=0 send_seq=10329 receive_seq=10329 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998594 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=54.6 th1: temp=52.9 th2: temp=59.7 th3: temp=57.2 sysload=0.79 cputime=414.937 memavail=7391056 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5603.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26200128 bytes_read=4029756 bytes_retransmit=9 bytes_invalid=0 send_seq=491692 receive_seq=491692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015878 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34792 bytes_read=109150 bytes_retransmit=0 bytes_invalid=0 send_seq=5770 receive_seq=5770 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997172 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170408 bytes_read=5315127 bytes_retransmit=9 bytes_invalid=0 send_seq=23534 receive_seq=23534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997611 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112704 bytes_read=2869829 bytes_retransmit=9 bytes_invalid=0 send_seq=15381 receive_seq=15381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997440 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35059 bytes_read=1429964 bytes_retransmit=9 bytes_invalid=0 send_seq=5784 receive_seq=5784 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997546 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35545 bytes_read=107013 bytes_retransmit=9 bytes_invalid=0 send_seq=5771 receive_seq=5771 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89637 bytes_read=2221674 bytes_retransmit=0 bytes_invalid=0 send_seq=10330 receive_seq=10330 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998619 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=54.5 th1: temp=52.9 th2: temp=59.6 th3: temp=57.1 sysload=0.79 cputime=414.980 memavail=7391056 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5604.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26200426 bytes_read=4030178 bytes_retransmit=9 bytes_invalid=0 send_seq=491715 receive_seq=491715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015876 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34798 bytes_read=109166 bytes_retransmit=0 bytes_invalid=0 send_seq=5771 receive_seq=5771 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997188 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170414 bytes_read=5315227 bytes_retransmit=9 bytes_invalid=0 send_seq=23535 receive_seq=23535 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997640 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112710 bytes_read=2869957 bytes_retransmit=9 bytes_invalid=0 send_seq=15382 receive_seq=15382 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997456 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35065 bytes_read=1430258 bytes_retransmit=9 bytes_invalid=0 send_seq=5785 receive_seq=5785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997572 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35551 bytes_read=107029 bytes_retransmit=9 bytes_invalid=0 send_seq=5772 receive_seq=5772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89643 bytes_read=2222030 bytes_retransmit=0 bytes_invalid=0 send_seq=10331 receive_seq=10331 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998631 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=54.3 th1: temp=52.8 th2: temp=59.7 th3: temp=57.0 sysload=0.79 cputime=415.024 memavail=7391056 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5605.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26200724 bytes_read=4030603 bytes_retransmit=9 bytes_invalid=0 send_seq=491738 receive_seq=491738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015878 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34804 bytes_read=109182 bytes_retransmit=0 bytes_invalid=0 send_seq=5772 receive_seq=5772 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997196 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170420 bytes_read=5315327 bytes_retransmit=9 bytes_invalid=0 send_seq=23536 receive_seq=23536 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997662 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112716 bytes_read=2870057 bytes_retransmit=9 bytes_invalid=0 send_seq=15383 receive_seq=15383 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997481 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35071 bytes_read=1430492 bytes_retransmit=9 bytes_invalid=0 send_seq=5786 receive_seq=5786 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997586 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35557 bytes_read=107045 bytes_retransmit=9 bytes_invalid=0 send_seq=5773 receive_seq=5773 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89649 bytes_read=2222386 bytes_retransmit=0 bytes_invalid=0 send_seq=10332 receive_seq=10332 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998645 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=54.1 th1: temp=52.8 th2: temp=59.6 th3: temp=57.0 sysload=0.72 cputime=415.068 memavail=7391056 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5606.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26201022 bytes_read=4031072 bytes_retransmit=9 bytes_invalid=0 send_seq=491761 receive_seq=491761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015873 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34810 bytes_read=109198 bytes_retransmit=0 bytes_invalid=0 send_seq=5773 receive_seq=5773 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997203 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170426 bytes_read=5315455 bytes_retransmit=9 bytes_invalid=0 send_seq=23537 receive_seq=23537 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997774 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112722 bytes_read=2870171 bytes_retransmit=9 bytes_invalid=0 send_seq=15384 receive_seq=15384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997575 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35077 bytes_read=1430726 bytes_retransmit=9 bytes_invalid=0 send_seq=5787 receive_seq=5787 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997595 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35563 bytes_read=107072 bytes_retransmit=9 bytes_invalid=0 send_seq=5774 receive_seq=5774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89655 bytes_read=2222742 bytes_retransmit=0 bytes_invalid=0 send_seq=10333 receive_seq=10333 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998649 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=54.1 th1: temp=52.7 th2: temp=59.8 th3: temp=57.1 sysload=0.72 cputime=415.115 memavail=7391056 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5607.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26201320 bytes_read=4031497 bytes_retransmit=9 bytes_invalid=0 send_seq=491784 receive_seq=491784 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015871 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34816 bytes_read=109227 bytes_retransmit=0 bytes_invalid=0 send_seq=5774 receive_seq=5774 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997223 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170432 bytes_read=5315569 bytes_retransmit=9 bytes_invalid=0 send_seq=23538 receive_seq=23538 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997751 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112728 bytes_read=2870285 bytes_retransmit=9 bytes_invalid=0 send_seq=15385 receive_seq=15385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35083 bytes_read=1431020 bytes_retransmit=9 bytes_invalid=0 send_seq=5788 receive_seq=5788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997605 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35569 bytes_read=107088 bytes_retransmit=9 bytes_invalid=0 send_seq=5775 receive_seq=5775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89661 bytes_read=2223098 bytes_retransmit=0 bytes_invalid=0 send_seq=10334 receive_seq=10334 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998663 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=54.3 th1: temp=52.4 th2: temp=59.7 th3: temp=57.2 sysload=0.72 cputime=415.163 memavail=7391344 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5608.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26201618 bytes_read=4031922 bytes_retransmit=9 bytes_invalid=0 send_seq=491807 receive_seq=491807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015887 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34822 bytes_read=109243 bytes_retransmit=0 bytes_invalid=0 send_seq=5775 receive_seq=5775 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997230 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170438 bytes_read=5315669 bytes_retransmit=9 bytes_invalid=0 send_seq=23539 receive_seq=23539 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997733 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112734 bytes_read=2870385 bytes_retransmit=9 bytes_invalid=0 send_seq=15386 receive_seq=15386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997540 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35089 bytes_read=1431269 bytes_retransmit=9 bytes_invalid=0 send_seq=5789 receive_seq=5789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997621 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35575 bytes_read=107104 bytes_retransmit=9 bytes_invalid=0 send_seq=5776 receive_seq=5776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89667 bytes_read=2223454 bytes_retransmit=0 bytes_invalid=0 send_seq=10335 receive_seq=10335 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998659 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=54.1 th1: temp=52.6 th2: temp=59.7 th3: temp=57.2 sysload=0.72 cputime=415.207 memavail=7391344 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5609.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26201911 bytes_read=4032371 bytes_retransmit=9 bytes_invalid=0 send_seq=491829 receive_seq=491829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015881 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34828 bytes_read=109259 bytes_retransmit=0 bytes_invalid=0 send_seq=5776 receive_seq=5776 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997192 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170444 bytes_read=5315797 bytes_retransmit=9 bytes_invalid=0 send_seq=23540 receive_seq=23540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997666 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112740 bytes_read=2870513 bytes_retransmit=9 bytes_invalid=0 send_seq=15387 receive_seq=15387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997478 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35095 bytes_read=1431503 bytes_retransmit=9 bytes_invalid=0 send_seq=5790 receive_seq=5790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35581 bytes_read=107120 bytes_retransmit=9 bytes_invalid=0 send_seq=5777 receive_seq=5777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89673 bytes_read=2223810 bytes_retransmit=0 bytes_invalid=0 send_seq=10336 receive_seq=10336 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998674 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=54.3 th1: temp=52.5 th2: temp=59.7 th3: temp=57.2 sysload=0.72 cputime=415.252 memavail=7392824 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5610.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26202209 bytes_read=4032796 bytes_retransmit=9 bytes_invalid=0 send_seq=491852 receive_seq=491852 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015879 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34834 bytes_read=109275 bytes_retransmit=0 bytes_invalid=0 send_seq=5777 receive_seq=5777 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997209 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170450 bytes_read=5315897 bytes_retransmit=9 bytes_invalid=0 send_seq=23541 receive_seq=23541 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997676 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112746 bytes_read=2870627 bytes_retransmit=9 bytes_invalid=0 send_seq=15388 receive_seq=15388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997484 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35101 bytes_read=1431797 bytes_retransmit=9 bytes_invalid=0 send_seq=5791 receive_seq=5791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35587 bytes_read=107136 bytes_retransmit=9 bytes_invalid=0 send_seq=5778 receive_seq=5778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89679 bytes_read=2224166 bytes_retransmit=0 bytes_invalid=0 send_seq=10337 receive_seq=10337 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998673 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=54.5 th1: temp=52.4 th2: temp=59.6 th3: temp=57.3 sysload=0.66 cputime=415.296 memavail=7392836 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5611.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26202507 bytes_read=4033236 bytes_retransmit=9 bytes_invalid=0 send_seq=491875 receive_seq=491875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015876 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34840 bytes_read=109291 bytes_retransmit=0 bytes_invalid=0 send_seq=5778 receive_seq=5778 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997219 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170456 bytes_read=5315997 bytes_retransmit=9 bytes_invalid=0 send_seq=23542 receive_seq=23542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997763 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112752 bytes_read=2870727 bytes_retransmit=9 bytes_invalid=0 send_seq=15389 receive_seq=15389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35107 bytes_read=1432031 bytes_retransmit=9 bytes_invalid=0 send_seq=5792 receive_seq=5792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35593 bytes_read=107163 bytes_retransmit=9 bytes_invalid=0 send_seq=5779 receive_seq=5779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89685 bytes_read=2224522 bytes_retransmit=0 bytes_invalid=0 send_seq=10338 receive_seq=10338 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998679 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=54.0 th1: temp=52.3 th2: temp=59.5 th3: temp=57.2 sysload=0.66 cputime=415.339 memavail=7392612 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5612.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26202800 bytes_read=4033685 bytes_retransmit=9 bytes_invalid=0 send_seq=491897 receive_seq=491897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015869 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34846 bytes_read=109320 bytes_retransmit=0 bytes_invalid=0 send_seq=5779 receive_seq=5779 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997241 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170462 bytes_read=5316139 bytes_retransmit=9 bytes_invalid=0 send_seq=23543 receive_seq=23543 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997832 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112758 bytes_read=2870841 bytes_retransmit=9 bytes_invalid=0 send_seq=15390 receive_seq=15390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35113 bytes_read=1432265 bytes_retransmit=9 bytes_invalid=0 send_seq=5793 receive_seq=5793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35599 bytes_read=107179 bytes_retransmit=9 bytes_invalid=0 send_seq=5780 receive_seq=5780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89691 bytes_read=2224878 bytes_retransmit=0 bytes_invalid=0 send_seq=10339 receive_seq=10339 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998679 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=54.0 th1: temp=52.3 th2: temp=59.7 th3: temp=57.1 sysload=0.66 cputime=415.383 memavail=7392612 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5613.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26203098 bytes_read=4034110 bytes_retransmit=9 bytes_invalid=0 send_seq=491920 receive_seq=491920 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015867 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34852 bytes_read=109336 bytes_retransmit=0 bytes_invalid=0 send_seq=5780 receive_seq=5780 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997259 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170468 bytes_read=5316235 bytes_retransmit=9 bytes_invalid=0 send_seq=23544 receive_seq=23544 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000252 adj=63997874 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112764 bytes_read=2870951 bytes_retransmit=9 bytes_invalid=0 send_seq=15391 receive_seq=15391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35119 bytes_read=1432559 bytes_retransmit=9 bytes_invalid=0 send_seq=5794 receive_seq=5794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997682 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35605 bytes_read=107195 bytes_retransmit=9 bytes_invalid=0 send_seq=5781 receive_seq=5781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89697 bytes_read=2225234 bytes_retransmit=0 bytes_invalid=0 send_seq=10340 receive_seq=10340 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998673 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=53.7 th1: temp=52.1 th2: temp=59.7 th3: temp=57.2 sysload=0.66 cputime=415.427 memavail=7392108 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5614.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26203391 bytes_read=4034528 bytes_retransmit=9 bytes_invalid=0 send_seq=491942 receive_seq=491942 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015865 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34858 bytes_read=109352 bytes_retransmit=0 bytes_invalid=0 send_seq=5781 receive_seq=5781 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997262 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170474 bytes_read=5316327 bytes_retransmit=9 bytes_invalid=0 send_seq=23545 receive_seq=23545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000250 adj=63998024 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112770 bytes_read=2871043 bytes_retransmit=9 bytes_invalid=0 send_seq=15392 receive_seq=15392 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997543 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35125 bytes_read=1432775 bytes_retransmit=9 bytes_invalid=0 send_seq=5795 receive_seq=5795 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35611 bytes_read=107211 bytes_retransmit=9 bytes_invalid=0 send_seq=5782 receive_seq=5782 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89703 bytes_read=2225590 bytes_retransmit=0 bytes_invalid=0 send_seq=10341 receive_seq=10341 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998670 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=53.8 th1: temp=52.2 th2: temp=59.9 th3: temp=57.1 sysload=0.66 cputime=415.471 memavail=7392112 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5615.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26203684 bytes_read=4034974 bytes_retransmit=9 bytes_invalid=0 send_seq=491964 receive_seq=491964 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015866 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34864 bytes_read=109368 bytes_retransmit=0 bytes_invalid=0 send_seq=5782 receive_seq=5782 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997258 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170480 bytes_read=5316446 bytes_retransmit=9 bytes_invalid=0 send_seq=23546 receive_seq=23546 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000248 adj=63997919 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=112776 bytes_read=2871163 bytes_retransmit=9 bytes_invalid=0 send_seq=15393 receive_seq=15393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997562 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35131 bytes_read=1432993 bytes_retransmit=9 bytes_invalid=0 send_seq=5796 receive_seq=5796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35617 bytes_read=107227 bytes_retransmit=9 bytes_invalid=0 send_seq=5783 receive_seq=5783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89709 bytes_read=2225946 bytes_retransmit=0 bytes_invalid=0 send_seq=10342 receive_seq=10342 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998675 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=53.7 th1: temp=52.2 th2: temp=59.8 th3: temp=57.2 sysload=0.77 cputime=415.516 memavail=7392112 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5616.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26203982 bytes_read=4035414 bytes_retransmit=9 bytes_invalid=0 send_seq=491987 receive_seq=491987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015899 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34870 bytes_read=109384 bytes_retransmit=0 bytes_invalid=0 send_seq=5783 receive_seq=5783 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997246 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170486 bytes_read=5316539 bytes_retransmit=9 bytes_invalid=0 send_seq=23547 receive_seq=23547 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000246 adj=63997830 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=112782 bytes_read=2871269 bytes_retransmit=9 bytes_invalid=0 send_seq=15394 receive_seq=15394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35137 bytes_read=1433267 bytes_retransmit=9 bytes_invalid=0 send_seq=5797 receive_seq=5797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35623 bytes_read=107254 bytes_retransmit=9 bytes_invalid=0 send_seq=5784 receive_seq=5784 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89715 bytes_read=2226302 bytes_retransmit=0 bytes_invalid=0 send_seq=10343 receive_seq=10343 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998669 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=54.0 th1: temp=52.1 th2: temp=59.7 th3: temp=57.1 sysload=0.77 cputime=415.567 memavail=7393020 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5617.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26204280 bytes_read=4035839 bytes_retransmit=9 bytes_invalid=0 send_seq=492010 receive_seq=492010 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015889 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34876 bytes_read=109413 bytes_retransmit=0 bytes_invalid=0 send_seq=5784 receive_seq=5784 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997191 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170492 bytes_read=5316648 bytes_retransmit=9 bytes_invalid=0 send_seq=23548 receive_seq=23548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000244 adj=63997688 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=112788 bytes_read=2871364 bytes_retransmit=9 bytes_invalid=0 send_seq=15395 receive_seq=15395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997439 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35143 bytes_read=1433485 bytes_retransmit=9 bytes_invalid=0 send_seq=5798 receive_seq=5798 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997598 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35629 bytes_read=107270 bytes_retransmit=9 bytes_invalid=0 send_seq=5785 receive_seq=5785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89721 bytes_read=2226658 bytes_retransmit=0 bytes_invalid=0 send_seq=10344 receive_seq=10344 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998643 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=53.7 th1: temp=52.1 th2: temp=59.7 th3: temp=57.1 sysload=0.77 cputime=415.611 memavail=7393020 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5618.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26204584 bytes_read=4036309 bytes_retransmit=9 bytes_invalid=0 send_seq=492034 receive_seq=492034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015876 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34888 bytes_read=109445 bytes_retransmit=0 bytes_invalid=0 send_seq=5786 receive_seq=5786 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997211 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170504 bytes_read=5316792 bytes_retransmit=9 bytes_invalid=0 send_seq=23550 receive_seq=23550 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000241 adj=63997678 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=112800 bytes_read=2871494 bytes_retransmit=9 bytes_invalid=0 send_seq=15397 receive_seq=15397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997475 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=35155 bytes_read=1433735 bytes_retransmit=9 bytes_invalid=0 send_seq=5800 receive_seq=5800 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997614 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35641 bytes_read=107302 bytes_retransmit=9 bytes_invalid=0 send_seq=5787 receive_seq=5787 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89733 bytes_read=2227030 bytes_retransmit=0 bytes_invalid=0 send_seq=10346 receive_seq=10346 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998725 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=53.6 th1: temp=52.1 th2: temp=59.7 th3: temp=57.1 sysload=0.77 cputime=415.658 memavail=7393020 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5619.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26204882 bytes_read=4036734 bytes_retransmit=9 bytes_invalid=0 send_seq=492057 receive_seq=492057 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015873 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34894 bytes_read=109461 bytes_retransmit=0 bytes_invalid=0 send_seq=5787 receive_seq=5787 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997263 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170510 bytes_read=5316892 bytes_retransmit=9 bytes_invalid=0 send_seq=23551 receive_seq=23551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000239 adj=63997662 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=112806 bytes_read=2871608 bytes_retransmit=9 bytes_invalid=0 send_seq=15398 receive_seq=15398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997508 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=35161 bytes_read=1434029 bytes_retransmit=9 bytes_invalid=0 send_seq=5801 receive_seq=5801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35647 bytes_read=107318 bytes_retransmit=9 bytes_invalid=0 send_seq=5788 receive_seq=5788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89739 bytes_read=2227370 bytes_retransmit=0 bytes_invalid=0 send_seq=10347 receive_seq=10347 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998697 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=53.5 th1: temp=52.3 th2: temp=59.6 th3: temp=57.0 sysload=0.77 cputime=415.703 memavail=7393020 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5620.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26205180 bytes_read=4037159 bytes_retransmit=9 bytes_invalid=0 send_seq=492080 receive_seq=492080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015871 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34900 bytes_read=109477 bytes_retransmit=0 bytes_invalid=0 send_seq=5788 receive_seq=5788 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997267 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170516 bytes_read=5316992 bytes_retransmit=9 bytes_invalid=0 send_seq=23552 receive_seq=23552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997654 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112812 bytes_read=2871722 bytes_retransmit=9 bytes_invalid=0 send_seq=15399 receive_seq=15399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=35167 bytes_read=1434263 bytes_retransmit=9 bytes_invalid=0 send_seq=5802 receive_seq=5802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35653 bytes_read=107334 bytes_retransmit=9 bytes_invalid=0 send_seq=5789 receive_seq=5789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89745 bytes_read=2227726 bytes_retransmit=0 bytes_invalid=0 send_seq=10348 receive_seq=10348 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998680 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.2 th2: temp=59.4 th3: temp=57.1 sysload=0.71 cputime=415.748 memavail=7395240 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 5621.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26205478 bytes_read=4037628 bytes_retransmit=9 bytes_invalid=0 send_seq=492103 receive_seq=492103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015873 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34906 bytes_read=109493 bytes_retransmit=0 bytes_invalid=0 send_seq=5789 receive_seq=5789 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997260 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170522 bytes_read=5317120 bytes_retransmit=9 bytes_invalid=0 send_seq=23553 receive_seq=23553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997646 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112818 bytes_read=2871836 bytes_retransmit=9 bytes_invalid=0 send_seq=15400 receive_seq=15400 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997508 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=35173 bytes_read=1434497 bytes_retransmit=9 bytes_invalid=0 send_seq=5803 receive_seq=5803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35659 bytes_read=107361 bytes_retransmit=9 bytes_invalid=0 send_seq=5790 receive_seq=5790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89751 bytes_read=2228082 bytes_retransmit=0 bytes_invalid=0 send_seq=10349 receive_seq=10349 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998691 coil_temp=16.9 refs=0 mcu_temp=20.14 supply_voltage=3.012 th0: temp=53.6 th1: temp=52.3 th2: temp=59.7 th3: temp=57.1 sysload=0.71 cputime=415.793 memavail=7395320 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5622.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26205771 bytes_read=4038048 bytes_retransmit=9 bytes_invalid=0 send_seq=492125 receive_seq=492125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015871 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34912 bytes_read=109522 bytes_retransmit=0 bytes_invalid=0 send_seq=5790 receive_seq=5790 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997247 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170528 bytes_read=5317234 bytes_retransmit=9 bytes_invalid=0 send_seq=23554 receive_seq=23554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997636 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112824 bytes_read=2871950 bytes_retransmit=9 bytes_invalid=0 send_seq=15401 receive_seq=15401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997521 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=35179 bytes_read=1434791 bytes_retransmit=9 bytes_invalid=0 send_seq=5804 receive_seq=5804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997634 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35665 bytes_read=107377 bytes_retransmit=9 bytes_invalid=0 send_seq=5791 receive_seq=5791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89757 bytes_read=2228438 bytes_retransmit=0 bytes_invalid=0 send_seq=10350 receive_seq=10350 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998674 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=53.5 th1: temp=52.1 th2: temp=59.6 th3: temp=57.1 sysload=0.71 cputime=415.837 memavail=7395320 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5623.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26206069 bytes_read=4038473 bytes_retransmit=9 bytes_invalid=0 send_seq=492148 receive_seq=492148 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015879 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34918 bytes_read=109538 bytes_retransmit=0 bytes_invalid=0 send_seq=5791 receive_seq=5791 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997242 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170534 bytes_read=5317334 bytes_retransmit=9 bytes_invalid=0 send_seq=23555 receive_seq=23555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997634 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112830 bytes_read=2872050 bytes_retransmit=9 bytes_invalid=0 send_seq=15402 receive_seq=15402 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35185 bytes_read=1435040 bytes_retransmit=9 bytes_invalid=0 send_seq=5805 receive_seq=5805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997630 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35671 bytes_read=107393 bytes_retransmit=9 bytes_invalid=0 send_seq=5792 receive_seq=5792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89763 bytes_read=2228794 bytes_retransmit=0 bytes_invalid=0 send_seq=10351 receive_seq=10351 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998673 coil_temp=16.9 refs=0 mcu_temp=20.16 supply_voltage=3.012 th0: temp=53.4 th1: temp=51.9 th2: temp=59.8 th3: temp=57.1 sysload=0.71 cputime=415.880 memavail=7395096 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5624.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26206367 bytes_read=4038927 bytes_retransmit=9 bytes_invalid=0 send_seq=492171 receive_seq=492171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015879 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34924 bytes_read=109554 bytes_retransmit=0 bytes_invalid=0 send_seq=5792 receive_seq=5792 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997236 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170540 bytes_read=5317462 bytes_retransmit=9 bytes_invalid=0 send_seq=23556 receive_seq=23556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997608 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112836 bytes_read=2872164 bytes_retransmit=9 bytes_invalid=0 send_seq=15403 receive_seq=15403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997485 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35191 bytes_read=1435274 bytes_retransmit=9 bytes_invalid=0 send_seq=5806 receive_seq=5806 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997615 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35677 bytes_read=107409 bytes_retransmit=9 bytes_invalid=0 send_seq=5793 receive_seq=5793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89769 bytes_read=2229150 bytes_retransmit=0 bytes_invalid=0 send_seq=10352 receive_seq=10352 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998659 coil_temp=16.9 refs=0 mcu_temp=20.16 supply_voltage=3.012 th0: temp=53.2 th1: temp=52.1 th2: temp=59.9 th3: temp=57.1 sysload=0.71 cputime=415.926 memavail=7395096 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.4 pwm=0.000
Stats 5625.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26206665 bytes_read=4039345 bytes_retransmit=9 bytes_invalid=0 send_seq=492194 receive_seq=492194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015881 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34930 bytes_read=109570 bytes_retransmit=0 bytes_invalid=0 send_seq=5793 receive_seq=5793 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997250 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170546 bytes_read=5317562 bytes_retransmit=9 bytes_invalid=0 send_seq=23557 receive_seq=23557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997609 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112842 bytes_read=2872292 bytes_retransmit=9 bytes_invalid=0 send_seq=15404 receive_seq=15404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35197 bytes_read=1435568 bytes_retransmit=9 bytes_invalid=0 send_seq=5807 receive_seq=5807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35683 bytes_read=107425 bytes_retransmit=9 bytes_invalid=0 send_seq=5794 receive_seq=5794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89775 bytes_read=2229506 bytes_retransmit=0 bytes_invalid=0 send_seq=10353 receive_seq=10353 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998647 coil_temp=16.9 refs=0 mcu_temp=20.16 supply_voltage=3.012 th0: temp=53.4 th1: temp=51.9 th2: temp=59.8 th3: temp=57.1 sysload=0.65 cputime=415.971 memavail=7395096 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5626.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26206963 bytes_read=4039785 bytes_retransmit=9 bytes_invalid=0 send_seq=492217 receive_seq=492217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015880 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34936 bytes_read=109586 bytes_retransmit=0 bytes_invalid=0 send_seq=5794 receive_seq=5794 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997246 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170552 bytes_read=5317662 bytes_retransmit=9 bytes_invalid=0 send_seq=23558 receive_seq=23558 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997602 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112848 bytes_read=2872392 bytes_retransmit=9 bytes_invalid=0 send_seq=15405 receive_seq=15405 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997484 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35203 bytes_read=1435802 bytes_retransmit=9 bytes_invalid=0 send_seq=5808 receive_seq=5808 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997632 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35689 bytes_read=107452 bytes_retransmit=9 bytes_invalid=0 send_seq=5795 receive_seq=5795 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89781 bytes_read=2229862 bytes_retransmit=0 bytes_invalid=0 send_seq=10354 receive_seq=10354 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998640 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=53.4 th1: temp=52.0 th2: temp=59.6 th3: temp=57.0 sysload=0.65 cputime=416.015 memavail=7395096 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5627.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26207256 bytes_read=4040234 bytes_retransmit=9 bytes_invalid=0 send_seq=492239 receive_seq=492239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015878 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34942 bytes_read=109615 bytes_retransmit=0 bytes_invalid=0 send_seq=5795 receive_seq=5795 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997243 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170558 bytes_read=5317804 bytes_retransmit=9 bytes_invalid=0 send_seq=23559 receive_seq=23559 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997617 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112854 bytes_read=2872506 bytes_retransmit=9 bytes_invalid=0 send_seq=15406 receive_seq=15406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997479 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35209 bytes_read=1436036 bytes_retransmit=9 bytes_invalid=0 send_seq=5809 receive_seq=5809 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997626 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35695 bytes_read=107468 bytes_retransmit=9 bytes_invalid=0 send_seq=5796 receive_seq=5796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89787 bytes_read=2230218 bytes_retransmit=0 bytes_invalid=0 send_seq=10355 receive_seq=10355 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998653 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=53.3 th1: temp=52.0 th2: temp=59.6 th3: temp=57.1 sysload=0.65 cputime=416.062 memavail=7394872 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5628.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26207554 bytes_read=4040659 bytes_retransmit=9 bytes_invalid=0 send_seq=492262 receive_seq=492262 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015876 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34948 bytes_read=109631 bytes_retransmit=0 bytes_invalid=0 send_seq=5796 receive_seq=5796 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997236 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170564 bytes_read=5317904 bytes_retransmit=9 bytes_invalid=0 send_seq=23560 receive_seq=23560 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997624 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112860 bytes_read=2872620 bytes_retransmit=9 bytes_invalid=0 send_seq=15407 receive_seq=15407 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997489 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35215 bytes_read=1436345 bytes_retransmit=9 bytes_invalid=0 send_seq=5810 receive_seq=5810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35701 bytes_read=107484 bytes_retransmit=9 bytes_invalid=0 send_seq=5797 receive_seq=5797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89793 bytes_read=2230574 bytes_retransmit=0 bytes_invalid=0 send_seq=10356 receive_seq=10356 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998649 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=53.2 th1: temp=52.1 th2: temp=59.9 th3: temp=57.1 sysload=0.65 cputime=416.107 memavail=7394872 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5629.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26207847 bytes_read=4041079 bytes_retransmit=9 bytes_invalid=0 send_seq=492284 receive_seq=492284 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016005 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34954 bytes_read=109647 bytes_retransmit=0 bytes_invalid=0 send_seq=5797 receive_seq=5797 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997238 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170570 bytes_read=5318004 bytes_retransmit=9 bytes_invalid=0 send_seq=23561 receive_seq=23561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997631 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112866 bytes_read=2872720 bytes_retransmit=9 bytes_invalid=0 send_seq=15408 receive_seq=15408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35221 bytes_read=1436579 bytes_retransmit=9 bytes_invalid=0 send_seq=5811 receive_seq=5811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997690 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35707 bytes_read=107500 bytes_retransmit=9 bytes_invalid=0 send_seq=5798 receive_seq=5798 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89799 bytes_read=2230930 bytes_retransmit=0 bytes_invalid=0 send_seq=10357 receive_seq=10357 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998668 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=53.5 th1: temp=52.0 th2: temp=59.6 th3: temp=57.1 sysload=0.65 cputime=416.149 memavail=7394872 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5630.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26208145 bytes_read=4041533 bytes_retransmit=9 bytes_invalid=0 send_seq=492307 receive_seq=492307 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015992 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34960 bytes_read=109663 bytes_retransmit=0 bytes_invalid=0 send_seq=5798 receive_seq=5798 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997005 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170576 bytes_read=5318132 bytes_retransmit=9 bytes_invalid=0 send_seq=23562 receive_seq=23562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997333 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112872 bytes_read=2872848 bytes_retransmit=9 bytes_invalid=0 send_seq=15409 receive_seq=15409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997165 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35227 bytes_read=1436813 bytes_retransmit=9 bytes_invalid=0 send_seq=5812 receive_seq=5812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997426 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35713 bytes_read=107516 bytes_retransmit=9 bytes_invalid=0 send_seq=5799 receive_seq=5799 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999383 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89805 bytes_read=2231286 bytes_retransmit=0 bytes_invalid=0 send_seq=10358 receive_seq=10358 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998494 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=53.2 th1: temp=51.9 th2: temp=59.6 th3: temp=57.3 sysload=0.60 cputime=416.194 memavail=7394872 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5631.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26208443 bytes_read=4041973 bytes_retransmit=9 bytes_invalid=0 send_seq=492330 receive_seq=492330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015978 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=34966 bytes_read=109679 bytes_retransmit=0 bytes_invalid=0 send_seq=5799 receive_seq=5799 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997093 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170582 bytes_read=5318232 bytes_retransmit=9 bytes_invalid=0 send_seq=23563 receive_seq=23563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997463 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112878 bytes_read=2872962 bytes_retransmit=9 bytes_invalid=0 send_seq=15410 receive_seq=15410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997271 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35233 bytes_read=1437107 bytes_retransmit=9 bytes_invalid=0 send_seq=5813 receive_seq=5813 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997496 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35719 bytes_read=107543 bytes_retransmit=9 bytes_invalid=0 send_seq=5800 receive_seq=5800 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999400 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89811 bytes_read=2231642 bytes_retransmit=0 bytes_invalid=0 send_seq=10359 receive_seq=10359 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998545 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=53.2 th1: temp=51.8 th2: temp=59.6 th3: temp=57.1 sysload=0.60 cputime=416.239 memavail=7395128 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5632.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26208741 bytes_read=4042398 bytes_retransmit=9 bytes_invalid=0 send_seq=492353 receive_seq=492353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016096 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=34972 bytes_read=109708 bytes_retransmit=0 bytes_invalid=0 send_seq=5800 receive_seq=5800 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997165 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170588 bytes_read=5318346 bytes_retransmit=9 bytes_invalid=0 send_seq=23564 receive_seq=23564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997548 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112884 bytes_read=2873062 bytes_retransmit=9 bytes_invalid=0 send_seq=15411 receive_seq=15411 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997355 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35239 bytes_read=1437341 bytes_retransmit=9 bytes_invalid=0 send_seq=5814 receive_seq=5814 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997547 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35725 bytes_read=107559 bytes_retransmit=9 bytes_invalid=0 send_seq=5801 receive_seq=5801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999415 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89817 bytes_read=2231998 bytes_retransmit=0 bytes_invalid=0 send_seq=10360 receive_seq=10360 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998580 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=53.2 th1: temp=51.9 th2: temp=59.6 th3: temp=57.1 sysload=0.60 cputime=416.282 memavail=7395128 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5633.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26209029 bytes_read=4042842 bytes_retransmit=9 bytes_invalid=0 send_seq=492374 receive_seq=492374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016081 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=34978 bytes_read=109724 bytes_retransmit=0 bytes_invalid=0 send_seq=5801 receive_seq=5801 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49996960 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170594 bytes_read=5318474 bytes_retransmit=9 bytes_invalid=0 send_seq=23565 receive_seq=23565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997278 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112890 bytes_read=2873176 bytes_retransmit=9 bytes_invalid=0 send_seq=15412 receive_seq=15412 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997090 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=35245 bytes_read=1437590 bytes_retransmit=9 bytes_invalid=0 send_seq=5815 receive_seq=5815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997349 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35731 bytes_read=107575 bytes_retransmit=9 bytes_invalid=0 send_seq=5802 receive_seq=5802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999368 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89823 bytes_read=2232354 bytes_retransmit=0 bytes_invalid=0 send_seq=10361 receive_seq=10361 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998470 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=53.3 th1: temp=51.8 th2: temp=59.7 th3: temp=57.1 sysload=0.60 cputime=416.333 memavail=7392888 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5634.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26209322 bytes_read=4043262 bytes_retransmit=9 bytes_invalid=0 send_seq=492396 receive_seq=492396 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016064 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=34984 bytes_read=109740 bytes_retransmit=0 bytes_invalid=0 send_seq=5802 receive_seq=5802 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997062 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170600 bytes_read=5318574 bytes_retransmit=9 bytes_invalid=0 send_seq=23566 receive_seq=23566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997398 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112896 bytes_read=2873290 bytes_retransmit=9 bytes_invalid=0 send_seq=15413 receive_seq=15413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997214 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=35251 bytes_read=1437884 bytes_retransmit=9 bytes_invalid=0 send_seq=5816 receive_seq=5816 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997539 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35737 bytes_read=107591 bytes_retransmit=9 bytes_invalid=0 send_seq=5803 receive_seq=5803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999402 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89829 bytes_read=2232710 bytes_retransmit=0 bytes_invalid=0 send_seq=10362 receive_seq=10362 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998543 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.011 th0: temp=53.0 th1: temp=51.7 th2: temp=59.6 th3: temp=57.2 sysload=0.60 cputime=416.377 memavail=7392968 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5635.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26209620 bytes_read=4043687 bytes_retransmit=9 bytes_invalid=0 send_seq=492419 receive_seq=492419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016047 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=34990 bytes_read=109756 bytes_retransmit=0 bytes_invalid=0 send_seq=5803 receive_seq=5803 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997132 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170606 bytes_read=5318674 bytes_retransmit=9 bytes_invalid=0 send_seq=23567 receive_seq=23567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997494 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112902 bytes_read=2873404 bytes_retransmit=9 bytes_invalid=0 send_seq=15414 receive_seq=15414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997314 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=35257 bytes_read=1438118 bytes_retransmit=9 bytes_invalid=0 send_seq=5817 receive_seq=5817 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997580 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35743 bytes_read=107607 bytes_retransmit=9 bytes_invalid=0 send_seq=5804 receive_seq=5804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999418 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89835 bytes_read=2233066 bytes_retransmit=0 bytes_invalid=0 send_seq=10363 receive_seq=10363 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998581 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=53.2 th1: temp=51.7 th2: temp=59.7 th3: temp=57.1 sysload=0.55 cputime=416.421 memavail=7392968 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 5636.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26209918 bytes_read=4044151 bytes_retransmit=9 bytes_invalid=0 send_seq=492442 receive_seq=492442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016036 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=34996 bytes_read=109772 bytes_retransmit=0 bytes_invalid=0 send_seq=5804 receive_seq=5804 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997181 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170612 bytes_read=5318802 bytes_retransmit=9 bytes_invalid=0 send_seq=23568 receive_seq=23568 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997562 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112908 bytes_read=2873518 bytes_retransmit=9 bytes_invalid=0 send_seq=15415 receive_seq=15415 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997391 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=35263 bytes_read=1438352 bytes_retransmit=9 bytes_invalid=0 send_seq=5818 receive_seq=5818 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35749 bytes_read=107634 bytes_retransmit=9 bytes_invalid=0 send_seq=5805 receive_seq=5805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89841 bytes_read=2233422 bytes_retransmit=0 bytes_invalid=0 send_seq=10364 receive_seq=10364 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998609 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=53.2 th1: temp=51.9 th2: temp=59.7 th3: temp=57.1 sysload=0.55 cputime=416.466 memavail=7392972 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5637.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26210216 bytes_read=4044576 bytes_retransmit=9 bytes_invalid=0 send_seq=492465 receive_seq=492465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016123 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=35002 bytes_read=109801 bytes_retransmit=0 bytes_invalid=0 send_seq=5805 receive_seq=5805 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997218 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170618 bytes_read=5318916 bytes_retransmit=9 bytes_invalid=0 send_seq=23569 receive_seq=23569 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997603 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112914 bytes_read=2873632 bytes_retransmit=9 bytes_invalid=0 send_seq=15416 receive_seq=15416 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997457 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=35269 bytes_read=1438646 bytes_retransmit=9 bytes_invalid=0 send_seq=5819 receive_seq=5819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35755 bytes_read=107650 bytes_retransmit=9 bytes_invalid=0 send_seq=5806 receive_seq=5806 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89847 bytes_read=2233778 bytes_retransmit=0 bytes_invalid=0 send_seq=10365 receive_seq=10365 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998627 coil_temp=16.9 refs=0 mcu_temp=20.16 supply_voltage=3.011 th0: temp=53.2 th1: temp=52.0 th2: temp=59.7 th3: temp=57.2 sysload=0.55 cputime=416.510 memavail=7391964 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Stats 5638.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26210514 bytes_read=4045001 bytes_retransmit=9 bytes_invalid=0 send_seq=492488 receive_seq=492488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016101 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=35008 bytes_read=109817 bytes_retransmit=0 bytes_invalid=0 send_seq=5806 receive_seq=5806 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997063 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170624 bytes_read=5319016 bytes_retransmit=9 bytes_invalid=0 send_seq=23570 receive_seq=23570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997398 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112920 bytes_read=2873732 bytes_retransmit=9 bytes_invalid=0 send_seq=15417 receive_seq=15417 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997240 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35275 bytes_read=1438895 bytes_retransmit=9 bytes_invalid=0 send_seq=5820 receive_seq=5820 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997463 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35761 bytes_read=107666 bytes_retransmit=9 bytes_invalid=0 send_seq=5807 receive_seq=5807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999392 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89853 bytes_read=2234134 bytes_retransmit=0 bytes_invalid=0 send_seq=10366 receive_seq=10366 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998520 coil_temp=16.9 refs=0 mcu_temp=20.16 supply_voltage=3.011 th0: temp=53.1 th1: temp=51.8 th2: temp=59.6 th3: temp=57.0 sysload=0.55 cputime=416.554 memavail=7391964 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5639.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26210812 bytes_read=4045455 bytes_retransmit=9 bytes_invalid=0 send_seq=492511 receive_seq=492511 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016157 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=35014 bytes_read=109833 bytes_retransmit=0 bytes_invalid=0 send_seq=5807 receive_seq=5807 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997162 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170630 bytes_read=5319144 bytes_retransmit=9 bytes_invalid=0 send_seq=23571 receive_seq=23571 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997509 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112926 bytes_read=2873846 bytes_retransmit=9 bytes_invalid=0 send_seq=15418 receive_seq=15418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997351 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35281 bytes_read=1439129 bytes_retransmit=9 bytes_invalid=0 send_seq=5821 receive_seq=5821 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997533 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35767 bytes_read=107682 bytes_retransmit=9 bytes_invalid=0 send_seq=5808 receive_seq=5808 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999411 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89859 bytes_read=2234490 bytes_retransmit=0 bytes_invalid=0 send_seq=10367 receive_seq=10367 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998570 coil_temp=16.9 refs=0 mcu_temp=20.17 supply_voltage=3.012 th0: temp=53.5 th1: temp=51.7 th2: temp=59.7 th3: temp=57.1 sysload=0.55 cputime=416.598 memavail=7391980 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5640.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26211110 bytes_read=4045880 bytes_retransmit=9 bytes_invalid=0 send_seq=492534 receive_seq=492534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016165 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=35020 bytes_read=109849 bytes_retransmit=0 bytes_invalid=0 send_seq=5808 receive_seq=5808 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997064 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170636 bytes_read=5319244 bytes_retransmit=9 bytes_invalid=0 send_seq=23572 receive_seq=23572 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997396 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112932 bytes_read=2873974 bytes_retransmit=9 bytes_invalid=0 send_seq=15419 receive_seq=15419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997249 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35287 bytes_read=1439423 bytes_retransmit=9 bytes_invalid=0 send_seq=5822 receive_seq=5822 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997442 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35773 bytes_read=107698 bytes_retransmit=9 bytes_invalid=0 send_seq=5809 receive_seq=5809 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999392 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89865 bytes_read=2234846 bytes_retransmit=0 bytes_invalid=0 send_seq=10368 receive_seq=10368 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998511 coil_temp=16.9 refs=0 mcu_temp=20.17 supply_voltage=3.012 th0: temp=53.1 th1: temp=51.6 th2: temp=59.6 th3: temp=57.1 sysload=0.51 cputime=416.642 memavail=7391980 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5641.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26211408 bytes_read=4046320 bytes_retransmit=9 bytes_invalid=0 send_seq=492557 receive_seq=492557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016144 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=35026 bytes_read=109865 bytes_retransmit=0 bytes_invalid=0 send_seq=5809 receive_seq=5809 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997125 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=170642 bytes_read=5319344 bytes_retransmit=9 bytes_invalid=0 send_seq=23573 receive_seq=23573 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997443 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112938 bytes_read=2874074 bytes_retransmit=9 bytes_invalid=0 send_seq=15420 receive_seq=15420 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997282 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35293 bytes_read=1439657 bytes_retransmit=9 bytes_invalid=0 send_seq=5823 receive_seq=5823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997472 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35779 bytes_read=107725 bytes_retransmit=9 bytes_invalid=0 send_seq=5810 receive_seq=5810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999408 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89871 bytes_read=2235202 bytes_retransmit=0 bytes_invalid=0 send_seq=10369 receive_seq=10369 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998526 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=53.1 th1: temp=51.8 th2: temp=59.9 th3: temp=57.1 sysload=0.51 cputime=416.687 memavail=7391980 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5642.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26211706 bytes_read=4046774 bytes_retransmit=9 bytes_invalid=0 send_seq=492580 receive_seq=492580 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016117 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=35032 bytes_read=109881 bytes_retransmit=0 bytes_invalid=0 send_seq=5810 receive_seq=5810 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997189 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170648 bytes_read=5319486 bytes_retransmit=9 bytes_invalid=0 send_seq=23574 receive_seq=23574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997565 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112944 bytes_read=2874188 bytes_retransmit=9 bytes_invalid=0 send_seq=15421 receive_seq=15421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997380 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35299 bytes_read=1439891 bytes_retransmit=9 bytes_invalid=0 send_seq=5824 receive_seq=5824 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997540 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35785 bytes_read=107741 bytes_retransmit=9 bytes_invalid=0 send_seq=5811 receive_seq=5811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89877 bytes_read=2235558 bytes_retransmit=0 bytes_invalid=0 send_seq=10370 receive_seq=10370 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998595 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=53.1 th1: temp=51.9 th2: temp=59.6 th3: temp=57.1 sysload=0.51 cputime=416.732 memavail=7391980 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5643.6: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26212004 bytes_read=4047199 bytes_retransmit=9 bytes_invalid=0 send_seq=492603 receive_seq=492603 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016094 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=35038 bytes_read=109910 bytes_retransmit=0 bytes_invalid=0 send_seq=5811 receive_seq=5811 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997251 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=170654 bytes_read=5319586 bytes_retransmit=9 bytes_invalid=0 send_seq=23575 receive_seq=23575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997665 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=112950 bytes_read=2874302 bytes_retransmit=9 bytes_invalid=0 send_seq=15422 receive_seq=15422 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997462 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=35305 bytes_read=1440200 bytes_retransmit=9 bytes_invalid=0 send_seq=5825 receive_seq=5825 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997601 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=35791 bytes_read=107757 bytes_retransmit=9 bytes_invalid=0 send_seq=5812 receive_seq=5812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=89883 bytes_read=2235914 bytes_retransmit=0 bytes_invalid=0 send_seq=10371 receive_seq=10371 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998635 coil_temp=16.9 refs=0 mcu_temp=20.14 supply_voltage=3.012 th0: temp=53.0 th1: temp=51.8 th2: temp=59.7 th3: temp=57.2 sysload=0.51 cputime=416.778 memavail=7391980 print_time=5607.071 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
RatOS:: Toolhead remapping deactivated!
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
RatOS:: Toolhead remapping deactivated!
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Extruder extruder already active
Extruder 'extruder' now syncing with 'extruder'
Extruder 'extruder1' now syncing with 'extruder'
RatOS | SET_PRESSURE_ADVANCE:: T0
extruder: pressure_advance: 0.008000
pressure_advance_smooth_time: 0.040000
RatOS | SET_PRESSURE_ADVANCE:: T1
extruder1: pressure_advance: 0.008000
pressure_advance_smooth_time: 0.040000
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 5936.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26302158 bytes_read=4175137 bytes_retransmit=9 bytes_invalid=0 send_seq=499291 receive_seq=499291 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400016266 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=36826 bytes_read=115413 bytes_retransmit=0 bytes_invalid=0 send_seq=6109 receive_seq=6109 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49996892 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172442 bytes_read=5352405 bytes_retransmit=9 bytes_invalid=0 send_seq=23873 receive_seq=23873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997167 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=114738 bytes_read=2907121 bytes_retransmit=9 bytes_invalid=0 send_seq=15720 receive_seq=15720 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63996994 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37093 bytes_read=1515302 bytes_retransmit=9 bytes_invalid=0 send_seq=6123 receive_seq=6123 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997269 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37579 bytes_read=113151 bytes_retransmit=9 bytes_invalid=0 send_seq=6110 receive_seq=6110 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999352 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91671 bytes_read=2340103 bytes_retransmit=0 bytes_invalid=0 send_seq=10669 receive_seq=10669 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998414 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=52.6 th1: temp=51.4 th2: temp=59.7 th3: temp=57.1 sysload=0.02 cputime=429.832 memavail=7393056 print_time=5960.973 buffer_time=1.475 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5937.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26302486 bytes_read=4175552 bytes_retransmit=9 bytes_invalid=0 send_seq=499312 receive_seq=499312 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016247 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=36832 bytes_read=115428 bytes_retransmit=0 bytes_invalid=0 send_seq=6110 receive_seq=6110 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49996977 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172448 bytes_read=5352519 bytes_retransmit=9 bytes_invalid=0 send_seq=23874 receive_seq=23874 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997300 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=114744 bytes_read=2907235 bytes_retransmit=9 bytes_invalid=0 send_seq=15721 receive_seq=15721 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997129 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37099 bytes_read=1515596 bytes_retransmit=9 bytes_invalid=0 send_seq=6124 receive_seq=6124 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997383 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37585 bytes_read=113167 bytes_retransmit=9 bytes_invalid=0 send_seq=6111 receive_seq=6111 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999375 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91677 bytes_read=2340459 bytes_retransmit=0 bytes_invalid=0 send_seq=10670 receive_seq=10670 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998477 coil_temp=16.9 refs=0 mcu_temp=20.16 supply_voltage=3.011 th0: temp=52.6 th1: temp=51.5 th2: temp=59.8 th3: temp=57.3 sysload=0.02 cputime=429.879 memavail=7392820 print_time=5960.973 buffer_time=0.474 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5938.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26302784 bytes_read=4175977 bytes_retransmit=9 bytes_invalid=0 send_seq=499335 receive_seq=499335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016225 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=36838 bytes_read=115443 bytes_retransmit=0 bytes_invalid=0 send_seq=6111 receive_seq=6111 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49996997 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172454 bytes_read=5352619 bytes_retransmit=9 bytes_invalid=0 send_seq=23875 receive_seq=23875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997338 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=114750 bytes_read=2907335 bytes_retransmit=9 bytes_invalid=0 send_seq=15722 receive_seq=15722 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997165 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37105 bytes_read=1515845 bytes_retransmit=9 bytes_invalid=0 send_seq=6125 receive_seq=6125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997423 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37591 bytes_read=113183 bytes_retransmit=9 bytes_invalid=0 send_seq=6112 receive_seq=6112 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999418 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91683 bytes_read=2340815 bytes_retransmit=0 bytes_invalid=0 send_seq=10671 receive_seq=10671 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998495 coil_temp=16.9 refs=0 mcu_temp=20.16 supply_voltage=3.011 th0: temp=52.8 th1: temp=51.4 th2: temp=59.8 th3: temp=57.2 sysload=0.02 cputime=429.923 memavail=7392820 print_time=5960.973 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5939.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26303082 bytes_read=4176431 bytes_retransmit=9 bytes_invalid=0 send_seq=499358 receive_seq=499358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016206 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=36844 bytes_read=115458 bytes_retransmit=0 bytes_invalid=0 send_seq=6112 receive_seq=6112 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997060 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172460 bytes_read=5352747 bytes_retransmit=9 bytes_invalid=0 send_seq=23876 receive_seq=23876 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997431 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114756 bytes_read=2907463 bytes_retransmit=9 bytes_invalid=0 send_seq=15723 receive_seq=15723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997245 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37111 bytes_read=1516079 bytes_retransmit=9 bytes_invalid=0 send_seq=6126 receive_seq=6126 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997495 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37597 bytes_read=113199 bytes_retransmit=9 bytes_invalid=0 send_seq=6113 receive_seq=6113 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91689 bytes_read=2341171 bytes_retransmit=0 bytes_invalid=0 send_seq=10672 receive_seq=10672 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998535 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=52.7 th1: temp=51.7 th2: temp=59.8 th3: temp=57.1 sysload=0.02 cputime=429.968 memavail=7392820 print_time=5960.973 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5940.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26303380 bytes_read=4176856 bytes_retransmit=9 bytes_invalid=0 send_seq=499381 receive_seq=499381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016183 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=36850 bytes_read=115474 bytes_retransmit=0 bytes_invalid=0 send_seq=6113 receive_seq=6113 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997131 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172466 bytes_read=5352847 bytes_retransmit=9 bytes_invalid=0 send_seq=23877 receive_seq=23877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997519 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114762 bytes_read=2907577 bytes_retransmit=9 bytes_invalid=0 send_seq=15724 receive_seq=15724 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997343 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37117 bytes_read=1516373 bytes_retransmit=9 bytes_invalid=0 send_seq=6127 receive_seq=6127 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997548 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37603 bytes_read=113215 bytes_retransmit=9 bytes_invalid=0 send_seq=6114 receive_seq=6114 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999475 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91695 bytes_read=2341527 bytes_retransmit=0 bytes_invalid=0 send_seq=10673 receive_seq=10673 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998580 coil_temp=16.9 refs=0 mcu_temp=20.16 supply_voltage=3.011 th0: temp=52.7 th1: temp=51.6 th2: temp=59.8 th3: temp=57.2 sysload=0.02 cputime=430.013 memavail=7392820 print_time=5960.973 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5941.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26303678 bytes_read=4177296 bytes_retransmit=9 bytes_invalid=0 send_seq=499404 receive_seq=499404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016160 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=36856 bytes_read=115503 bytes_retransmit=0 bytes_invalid=0 send_seq=6114 receive_seq=6114 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997189 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172472 bytes_read=5352961 bytes_retransmit=9 bytes_invalid=0 send_seq=23878 receive_seq=23878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997588 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114768 bytes_read=2907677 bytes_retransmit=9 bytes_invalid=0 send_seq=15725 receive_seq=15725 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997417 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37123 bytes_read=1516607 bytes_retransmit=9 bytes_invalid=0 send_seq=6128 receive_seq=6128 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997611 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37609 bytes_read=113242 bytes_retransmit=9 bytes_invalid=0 send_seq=6115 receive_seq=6115 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999473 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91701 bytes_read=2341883 bytes_retransmit=0 bytes_invalid=0 send_seq=10674 receive_seq=10674 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998626 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=52.8 th1: temp=52.1 th2: temp=59.5 th3: temp=57.3 sysload=0.02 cputime=430.059 memavail=7392820 print_time=5960.973 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
RatOS:: Toolhead remapping deactivated!
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 5942.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26305336 bytes_read=4177840 bytes_retransmit=9 bytes_invalid=0 send_seq=499449 receive_seq=499445 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400016141 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=36862 bytes_read=115519 bytes_retransmit=0 bytes_invalid=0 send_seq=6115 receive_seq=6115 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997229 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172478 bytes_read=5353089 bytes_retransmit=9 bytes_invalid=0 send_seq=23879 receive_seq=23879 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997644 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114774 bytes_read=2907791 bytes_retransmit=9 bytes_invalid=0 send_seq=15726 receive_seq=15726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997484 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37129 bytes_read=1516841 bytes_retransmit=9 bytes_invalid=0 send_seq=6129 receive_seq=6129 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37615 bytes_read=113258 bytes_retransmit=9 bytes_invalid=0 send_seq=6116 receive_seq=6116 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999923 adj=11999469 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91707 bytes_read=2342239 bytes_retransmit=0 bytes_invalid=0 send_seq=10675 receive_seq=10675 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998661 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=52.7 th1: temp=51.7 th2: temp=59.7 th3: temp=57.2 sysload=0.02 cputime=430.136 memavail=7392832 print_time=5965.770 buffer_time=0.269 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Extruder extruder already active
Extruder 'extruder' now syncing with 'extruder'
Extruder 'extruder1' now syncing with 'extruder1'
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 5943.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26305650 bytes_read=4178285 bytes_retransmit=9 bytes_invalid=0 send_seq=499472 receive_seq=499472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016129 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=36868 bytes_read=115535 bytes_retransmit=0 bytes_invalid=0 send_seq=6116 receive_seq=6116 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997261 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172484 bytes_read=5353189 bytes_retransmit=9 bytes_invalid=0 send_seq=23880 receive_seq=23880 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997677 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114780 bytes_read=2907905 bytes_retransmit=9 bytes_invalid=0 send_seq=15727 receive_seq=15727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997552 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37135 bytes_read=1517150 bytes_retransmit=9 bytes_invalid=0 send_seq=6130 receive_seq=6130 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37621 bytes_read=113274 bytes_retransmit=9 bytes_invalid=0 send_seq=6117 receive_seq=6117 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999484 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91713 bytes_read=2342595 bytes_retransmit=0 bytes_invalid=0 send_seq=10676 receive_seq=10676 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998683 coil_temp=16.9 refs=0 mcu_temp=20.14 supply_voltage=3.011 th0: temp=52.9 th1: temp=51.9 th2: temp=59.6 th3: temp=57.2 sysload=0.02 cputime=430.200 memavail=7387036 print_time=5965.770 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5944.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26305948 bytes_read=4178710 bytes_retransmit=9 bytes_invalid=0 send_seq=499495 receive_seq=499495 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016119 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=36874 bytes_read=115551 bytes_retransmit=0 bytes_invalid=0 send_seq=6117 receive_seq=6117 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997312 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172490 bytes_read=5353289 bytes_retransmit=9 bytes_invalid=0 send_seq=23881 receive_seq=23881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997689 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114786 bytes_read=2908019 bytes_retransmit=9 bytes_invalid=0 send_seq=15728 receive_seq=15728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997580 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37141 bytes_read=1517384 bytes_retransmit=9 bytes_invalid=0 send_seq=6131 receive_seq=6131 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997683 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37627 bytes_read=113290 bytes_retransmit=9 bytes_invalid=0 send_seq=6118 receive_seq=6118 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999476 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91719 bytes_read=2342951 bytes_retransmit=0 bytes_invalid=0 send_seq=10677 receive_seq=10677 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998701 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.011 th0: temp=52.7 th1: temp=51.7 th2: temp=59.6 th3: temp=57.2 sysload=0.02 cputime=430.245 memavail=7394456 print_time=5965.770 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 5945.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26306246 bytes_read=4179164 bytes_retransmit=9 bytes_invalid=0 send_seq=499518 receive_seq=499518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016104 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=36880 bytes_read=115567 bytes_retransmit=0 bytes_invalid=0 send_seq=6118 receive_seq=6118 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997307 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172496 bytes_read=5353417 bytes_retransmit=9 bytes_invalid=0 send_seq=23882 receive_seq=23882 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997709 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114792 bytes_read=2908133 bytes_retransmit=9 bytes_invalid=0 send_seq=15729 receive_seq=15729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997566 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37147 bytes_read=1517618 bytes_retransmit=9 bytes_invalid=0 send_seq=6132 receive_seq=6132 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37633 bytes_read=113306 bytes_retransmit=9 bytes_invalid=0 send_seq=6119 receive_seq=6119 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999468 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91725 bytes_read=2343307 bytes_retransmit=0 bytes_invalid=0 send_seq=10678 receive_seq=10678 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998693 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=52.5 th1: temp=52.0 th2: temp=59.7 th3: temp=57.1 sysload=0.02 cputime=430.290 memavail=7394456 print_time=5965.770 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Extruder extruder already active
Extruder 'extruder' now syncing with 'extruder'
Extruder 'extruder1' now syncing with 'extruder'
RatOS | SET_PRESSURE_ADVANCE:: T0
extruder: pressure_advance: 0.008000
pressure_advance_smooth_time: 0.040000
RatOS | SET_PRESSURE_ADVANCE:: T1
extruder1: pressure_advance: 0.008000
pressure_advance_smooth_time: 0.040000
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 5946.9: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26309935 bytes_read=4179879 bytes_retransmit=9 bytes_invalid=0 send_seq=499596 receive_seq=499596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016085 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=36886 bytes_read=115596 bytes_retransmit=0 bytes_invalid=0 send_seq=6119 receive_seq=6119 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997347 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172502 bytes_read=5353531 bytes_retransmit=9 bytes_invalid=0 send_seq=23883 receive_seq=23883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997821 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114798 bytes_read=2908247 bytes_retransmit=9 bytes_invalid=0 send_seq=15730 receive_seq=15730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997573 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37153 bytes_read=1517912 bytes_retransmit=9 bytes_invalid=0 send_seq=6133 receive_seq=6133 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37639 bytes_read=113333 bytes_retransmit=9 bytes_invalid=0 send_seq=6120 receive_seq=6120 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91731 bytes_read=2343663 bytes_retransmit=0 bytes_invalid=0 send_seq=10679 receive_seq=10679 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998697 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=52.8 th1: temp=52.2 th2: temp=59.7 th3: temp=57.2 sysload=0.02 cputime=430.405 memavail=7394456 print_time=5970.195 buffer_time=0.693 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5947.9: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26310233 bytes_read=4180299 bytes_retransmit=9 bytes_invalid=0 send_seq=499619 receive_seq=499619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016067 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=36892 bytes_read=115612 bytes_retransmit=0 bytes_invalid=0 send_seq=6120 receive_seq=6120 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997381 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172508 bytes_read=5353631 bytes_retransmit=9 bytes_invalid=0 send_seq=23884 receive_seq=23884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997793 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114804 bytes_read=2908347 bytes_retransmit=9 bytes_invalid=0 send_seq=15731 receive_seq=15731 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997617 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37159 bytes_read=1518146 bytes_retransmit=9 bytes_invalid=0 send_seq=6134 receive_seq=6134 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37645 bytes_read=113349 bytes_retransmit=9 bytes_invalid=0 send_seq=6121 receive_seq=6121 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999456 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91737 bytes_read=2344019 bytes_retransmit=0 bytes_invalid=0 send_seq=10680 receive_seq=10680 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998738 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=52.7 th1: temp=52.3 th2: temp=59.7 th3: temp=57.2 sysload=0.02 cputime=430.449 memavail=7393236 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 5948.9: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26310531 bytes_read=4180753 bytes_retransmit=9 bytes_invalid=0 send_seq=499642 receive_seq=499642 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016047 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=36898 bytes_read=115628 bytes_retransmit=0 bytes_invalid=0 send_seq=6121 receive_seq=6121 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997398 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172514 bytes_read=5353755 bytes_retransmit=9 bytes_invalid=0 send_seq=23885 receive_seq=23885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997814 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114810 bytes_read=2908458 bytes_retransmit=9 bytes_invalid=0 send_seq=15732 receive_seq=15732 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997744 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37165 bytes_read=1518395 bytes_retransmit=9 bytes_invalid=0 send_seq=6135 receive_seq=6135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997726 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37651 bytes_read=113365 bytes_retransmit=9 bytes_invalid=0 send_seq=6122 receive_seq=6122 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91743 bytes_read=2344375 bytes_retransmit=0 bytes_invalid=0 send_seq=10681 receive_seq=10681 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998764 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=52.7 th1: temp=52.4 th2: temp=59.7 th3: temp=57.1 sysload=0.02 cputime=430.493 memavail=7393236 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5949.9: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26310829 bytes_read=4181178 bytes_retransmit=9 bytes_invalid=0 send_seq=499665 receive_seq=499665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016027 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=36904 bytes_read=115644 bytes_retransmit=0 bytes_invalid=0 send_seq=6122 receive_seq=6122 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997398 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172520 bytes_read=5353848 bytes_retransmit=9 bytes_invalid=0 send_seq=23886 receive_seq=23886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997815 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114816 bytes_read=2908578 bytes_retransmit=9 bytes_invalid=0 send_seq=15733 receive_seq=15733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997713 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37171 bytes_read=1518689 bytes_retransmit=9 bytes_invalid=0 send_seq=6136 receive_seq=6136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997729 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37657 bytes_read=113381 bytes_retransmit=9 bytes_invalid=0 send_seq=6123 receive_seq=6123 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91749 bytes_read=2344731 bytes_retransmit=0 bytes_invalid=0 send_seq=10682 receive_seq=10682 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998847 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=52.8 th1: temp=52.5 th2: temp=59.8 th3: temp=57.1 sysload=0.02 cputime=430.537 memavail=7393236 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5950.9: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26311127 bytes_read=4181603 bytes_retransmit=9 bytes_invalid=0 send_seq=499688 receive_seq=499688 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016021 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=36910 bytes_read=115660 bytes_retransmit=0 bytes_invalid=0 send_seq=6123 receive_seq=6123 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999249 adj=49997413 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172526 bytes_read=5353941 bytes_retransmit=9 bytes_invalid=0 send_seq=23887 receive_seq=23887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997819 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114822 bytes_read=2908671 bytes_retransmit=9 bytes_invalid=0 send_seq=15734 receive_seq=15734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997700 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37177 bytes_read=1518923 bytes_retransmit=9 bytes_invalid=0 send_seq=6137 receive_seq=6137 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997734 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37663 bytes_read=113397 bytes_retransmit=9 bytes_invalid=0 send_seq=6124 receive_seq=6124 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91755 bytes_read=2345087 bytes_retransmit=0 bytes_invalid=0 send_seq=10683 receive_seq=10683 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998832 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=52.4 th1: temp=52.3 th2: temp=59.8 th3: temp=57.2 sysload=0.02 cputime=430.580 memavail=7393236 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5951.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26311425 bytes_read=4182072 bytes_retransmit=9 bytes_invalid=0 send_seq=499711 receive_seq=499711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016008 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=36916 bytes_read=115689 bytes_retransmit=0 bytes_invalid=0 send_seq=6124 receive_seq=6124 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999248 adj=49997407 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=172532 bytes_read=5354074 bytes_retransmit=9 bytes_invalid=0 send_seq=23888 receive_seq=23888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997781 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114828 bytes_read=2908777 bytes_retransmit=9 bytes_invalid=0 send_seq=15735 receive_seq=15735 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997648 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37183 bytes_read=1519157 bytes_retransmit=9 bytes_invalid=0 send_seq=6138 receive_seq=6138 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997718 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37669 bytes_read=113424 bytes_retransmit=9 bytes_invalid=0 send_seq=6125 receive_seq=6125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91761 bytes_read=2345443 bytes_retransmit=0 bytes_invalid=0 send_seq=10684 receive_seq=10684 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998789 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=52.6 th1: temp=52.4 th2: temp=59.7 th3: temp=57.3 sysload=0.02 cputime=430.624 memavail=7393236 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5952.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26311723 bytes_read=4182497 bytes_retransmit=9 bytes_invalid=0 send_seq=499734 receive_seq=499734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015996 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=36922 bytes_read=115705 bytes_retransmit=0 bytes_invalid=0 send_seq=6125 receive_seq=6125 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997377 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=172538 bytes_read=5354169 bytes_retransmit=9 bytes_invalid=0 send_seq=23889 receive_seq=23889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997814 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114834 bytes_read=2908885 bytes_retransmit=9 bytes_invalid=0 send_seq=15736 receive_seq=15736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997625 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37189 bytes_read=1519451 bytes_retransmit=9 bytes_invalid=0 send_seq=6139 receive_seq=6139 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997712 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37675 bytes_read=113440 bytes_retransmit=9 bytes_invalid=0 send_seq=6126 receive_seq=6126 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91767 bytes_read=2345799 bytes_retransmit=0 bytes_invalid=0 send_seq=10685 receive_seq=10685 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998765 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=52.6 th1: temp=52.8 th2: temp=59.7 th3: temp=57.2 sysload=0.02 cputime=430.667 memavail=7393236 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5953.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26312021 bytes_read=4182922 bytes_retransmit=9 bytes_invalid=0 send_seq=499757 receive_seq=499757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015984 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=36928 bytes_read=115721 bytes_retransmit=0 bytes_invalid=0 send_seq=6126 receive_seq=6126 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997351 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=172544 bytes_read=5354269 bytes_retransmit=9 bytes_invalid=0 send_seq=23890 receive_seq=23890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997790 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114840 bytes_read=2908985 bytes_retransmit=9 bytes_invalid=0 send_seq=15737 receive_seq=15737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997615 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37195 bytes_read=1519700 bytes_retransmit=9 bytes_invalid=0 send_seq=6140 receive_seq=6140 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997708 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37681 bytes_read=113456 bytes_retransmit=9 bytes_invalid=0 send_seq=6127 receive_seq=6127 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91773 bytes_read=2346155 bytes_retransmit=0 bytes_invalid=0 send_seq=10686 receive_seq=10686 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999950 adj=31998812 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=52.4 th1: temp=52.5 th2: temp=59.8 th3: temp=57.1 sysload=0.02 cputime=430.710 memavail=7393236 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 5954.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26312319 bytes_read=4183376 bytes_retransmit=9 bytes_invalid=0 send_seq=499780 receive_seq=499780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015974 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=36934 bytes_read=115737 bytes_retransmit=0 bytes_invalid=0 send_seq=6127 receive_seq=6127 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997341 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=172550 bytes_read=5354397 bytes_retransmit=9 bytes_invalid=0 send_seq=23891 receive_seq=23891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997775 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=114846 bytes_read=2909113 bytes_retransmit=9 bytes_invalid=0 send_seq=15738 receive_seq=15738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997603 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37201 bytes_read=1519934 bytes_retransmit=9 bytes_invalid=0 send_seq=6141 receive_seq=6141 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997715 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37687 bytes_read=113472 bytes_retransmit=9 bytes_invalid=0 send_seq=6128 receive_seq=6128 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91779 bytes_read=2346511 bytes_retransmit=0 bytes_invalid=0 send_seq=10687 receive_seq=10687 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999950 adj=31998849 coil_temp=16.9 refs=0 mcu_temp=20.12 supply_voltage=3.012 th0: temp=52.6 th1: temp=52.7 th2: temp=59.6 th3: temp=57.1 sysload=0.02 cputime=430.754 memavail=7393236 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5955.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26312617 bytes_read=4183801 bytes_retransmit=9 bytes_invalid=0 send_seq=499803 receive_seq=499803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015964 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=36940 bytes_read=115753 bytes_retransmit=0 bytes_invalid=0 send_seq=6128 receive_seq=6128 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997326 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=172556 bytes_read=5354497 bytes_retransmit=9 bytes_invalid=0 send_seq=23892 receive_seq=23892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997760 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=114852 bytes_read=2909227 bytes_retransmit=9 bytes_invalid=0 send_seq=15739 receive_seq=15739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997585 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37207 bytes_read=1520228 bytes_retransmit=9 bytes_invalid=0 send_seq=6142 receive_seq=6142 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997707 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37693 bytes_read=113488 bytes_retransmit=9 bytes_invalid=0 send_seq=6129 receive_seq=6129 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91785 bytes_read=2346867 bytes_retransmit=0 bytes_invalid=0 send_seq=10688 receive_seq=10688 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999948 adj=31998810 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=52.6 th1: temp=52.5 th2: temp=59.8 th3: temp=57.3 sysload=0.01 cputime=430.797 memavail=7393236 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5956.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26312915 bytes_read=4184241 bytes_retransmit=9 bytes_invalid=0 send_seq=499826 receive_seq=499826 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015956 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=36946 bytes_read=115782 bytes_retransmit=0 bytes_invalid=0 send_seq=6129 receive_seq=6129 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997318 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=172562 bytes_read=5354597 bytes_retransmit=9 bytes_invalid=0 send_seq=23893 receive_seq=23893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997752 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=114858 bytes_read=2909327 bytes_retransmit=9 bytes_invalid=0 send_seq=15740 receive_seq=15740 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997576 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37213 bytes_read=1520462 bytes_retransmit=9 bytes_invalid=0 send_seq=6143 receive_seq=6143 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997700 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37699 bytes_read=113515 bytes_retransmit=9 bytes_invalid=0 send_seq=6130 receive_seq=6130 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91791 bytes_read=2347223 bytes_retransmit=0 bytes_invalid=0 send_seq=10689 receive_seq=10689 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999948 adj=31998772 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=52.6 th1: temp=52.7 th2: temp=59.8 th3: temp=57.3 sysload=0.01 cputime=430.840 memavail=7393236 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5957.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26313213 bytes_read=4184693 bytes_retransmit=9 bytes_invalid=0 send_seq=499849 receive_seq=499849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015949 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=36952 bytes_read=115798 bytes_retransmit=0 bytes_invalid=0 send_seq=6130 receive_seq=6130 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997300 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172568 bytes_read=5354739 bytes_retransmit=9 bytes_invalid=0 send_seq=23894 receive_seq=23894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997739 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=114864 bytes_read=2909441 bytes_retransmit=9 bytes_invalid=0 send_seq=15741 receive_seq=15741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37219 bytes_read=1520696 bytes_retransmit=9 bytes_invalid=0 send_seq=6144 receive_seq=6144 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997692 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37705 bytes_read=113531 bytes_retransmit=9 bytes_invalid=0 send_seq=6131 receive_seq=6131 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91797 bytes_read=2347579 bytes_retransmit=0 bytes_invalid=0 send_seq=10690 receive_seq=10690 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999947 adj=31998744 coil_temp=16.9 refs=0 mcu_temp=20.11 supply_voltage=3.012 th0: temp=52.4 th1: temp=52.5 th2: temp=59.7 th3: temp=57.2 sysload=0.01 cputime=430.886 memavail=7392228 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5958.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26313511 bytes_read=4185115 bytes_retransmit=9 bytes_invalid=0 send_seq=499872 receive_seq=499872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015945 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=36958 bytes_read=115814 bytes_retransmit=0 bytes_invalid=0 send_seq=6131 receive_seq=6131 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997293 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172574 bytes_read=5354839 bytes_retransmit=9 bytes_invalid=0 send_seq=23895 receive_seq=23895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997731 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=114870 bytes_read=2909555 bytes_retransmit=9 bytes_invalid=0 send_seq=15742 receive_seq=15742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37225 bytes_read=1521005 bytes_retransmit=9 bytes_invalid=0 send_seq=6145 receive_seq=6145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997693 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37711 bytes_read=113547 bytes_retransmit=9 bytes_invalid=0 send_seq=6132 receive_seq=6132 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91803 bytes_read=2347935 bytes_retransmit=0 bytes_invalid=0 send_seq=10691 receive_seq=10691 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998719 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=52.5 th1: temp=52.7 th2: temp=59.8 th3: temp=57.2 sysload=0.01 cputime=430.930 memavail=7392228 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5959.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26313809 bytes_read=4185540 bytes_retransmit=9 bytes_invalid=0 send_seq=499895 receive_seq=499895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015939 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=36964 bytes_read=115830 bytes_retransmit=0 bytes_invalid=0 send_seq=6132 receive_seq=6132 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997281 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172580 bytes_read=5354939 bytes_retransmit=9 bytes_invalid=0 send_seq=23896 receive_seq=23896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997711 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114876 bytes_read=2909669 bytes_retransmit=9 bytes_invalid=0 send_seq=15743 receive_seq=15743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997546 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37231 bytes_read=1521239 bytes_retransmit=9 bytes_invalid=0 send_seq=6146 receive_seq=6146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37717 bytes_read=113563 bytes_retransmit=9 bytes_invalid=0 send_seq=6133 receive_seq=6133 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91809 bytes_read=2348291 bytes_retransmit=0 bytes_invalid=0 send_seq=10692 receive_seq=10692 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998709 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=52.4 th1: temp=52.6 th2: temp=59.8 th3: temp=57.2 sysload=0.01 cputime=430.973 memavail=7392264 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5960.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26314107 bytes_read=4185994 bytes_retransmit=9 bytes_invalid=0 send_seq=499918 receive_seq=499918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015932 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=36970 bytes_read=115846 bytes_retransmit=0 bytes_invalid=0 send_seq=6133 receive_seq=6133 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997279 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172586 bytes_read=5355067 bytes_retransmit=9 bytes_invalid=0 send_seq=23897 receive_seq=23897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997709 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114882 bytes_read=2909783 bytes_retransmit=9 bytes_invalid=0 send_seq=15744 receive_seq=15744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997540 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37237 bytes_read=1521473 bytes_retransmit=9 bytes_invalid=0 send_seq=6147 receive_seq=6147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997677 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37723 bytes_read=113579 bytes_retransmit=9 bytes_invalid=0 send_seq=6134 receive_seq=6134 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999467 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91815 bytes_read=2348647 bytes_retransmit=0 bytes_invalid=0 send_seq=10693 receive_seq=10693 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998709 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=52.5 th1: temp=52.7 th2: temp=59.8 th3: temp=57.2 sysload=0.01 cputime=431.021 memavail=7385208 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5961.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26314405 bytes_read=4186434 bytes_retransmit=9 bytes_invalid=0 send_seq=499941 receive_seq=499941 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015928 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=36976 bytes_read=115875 bytes_retransmit=0 bytes_invalid=0 send_seq=6134 receive_seq=6134 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997276 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172592 bytes_read=5355167 bytes_retransmit=9 bytes_invalid=0 send_seq=23898 receive_seq=23898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997711 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114888 bytes_read=2909897 bytes_retransmit=9 bytes_invalid=0 send_seq=15745 receive_seq=15745 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997536 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37243 bytes_read=1521767 bytes_retransmit=9 bytes_invalid=0 send_seq=6148 receive_seq=6148 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37729 bytes_read=113606 bytes_retransmit=9 bytes_invalid=0 send_seq=6135 receive_seq=6135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91821 bytes_read=2349003 bytes_retransmit=0 bytes_invalid=0 send_seq=10694 receive_seq=10694 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998687 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=52.3 th1: temp=52.8 th2: temp=59.7 th3: temp=57.2 sysload=0.01 cputime=431.066 memavail=7391588 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5962.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26314703 bytes_read=4186859 bytes_retransmit=9 bytes_invalid=0 send_seq=499964 receive_seq=499964 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015950 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=36982 bytes_read=115891 bytes_retransmit=0 bytes_invalid=0 send_seq=6135 receive_seq=6135 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997270 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172598 bytes_read=5355281 bytes_retransmit=9 bytes_invalid=0 send_seq=23899 receive_seq=23899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997706 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114894 bytes_read=2909997 bytes_retransmit=9 bytes_invalid=0 send_seq=15746 receive_seq=15746 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37249 bytes_read=1522001 bytes_retransmit=9 bytes_invalid=0 send_seq=6149 receive_seq=6149 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997694 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37735 bytes_read=113622 bytes_retransmit=9 bytes_invalid=0 send_seq=6136 receive_seq=6136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91827 bytes_read=2349359 bytes_retransmit=0 bytes_invalid=0 send_seq=10695 receive_seq=10695 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998685 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=52.4 th1: temp=52.6 th2: temp=59.9 th3: temp=57.1 sysload=0.01 cputime=431.109 memavail=7391588 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5963.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26315001 bytes_read=4187313 bytes_retransmit=9 bytes_invalid=0 send_seq=499987 receive_seq=499987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015946 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=36988 bytes_read=115907 bytes_retransmit=0 bytes_invalid=0 send_seq=6136 receive_seq=6136 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997274 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172604 bytes_read=5355409 bytes_retransmit=9 bytes_invalid=0 send_seq=23900 receive_seq=23900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997637 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114900 bytes_read=2910111 bytes_retransmit=9 bytes_invalid=0 send_seq=15747 receive_seq=15747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997464 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37255 bytes_read=1522250 bytes_retransmit=9 bytes_invalid=0 send_seq=6150 receive_seq=6150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37741 bytes_read=113638 bytes_retransmit=9 bytes_invalid=0 send_seq=6137 receive_seq=6137 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91833 bytes_read=2349715 bytes_retransmit=0 bytes_invalid=0 send_seq=10696 receive_seq=10696 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998643 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=52.3 th1: temp=52.9 th2: temp=59.7 th3: temp=57.4 sysload=0.01 cputime=431.153 memavail=7391588 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 5964.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26315299 bytes_read=4187738 bytes_retransmit=9 bytes_invalid=0 send_seq=500010 receive_seq=500010 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015964 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=36994 bytes_read=115923 bytes_retransmit=0 bytes_invalid=0 send_seq=6137 receive_seq=6137 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997264 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172610 bytes_read=5355509 bytes_retransmit=9 bytes_invalid=0 send_seq=23901 receive_seq=23901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997731 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114906 bytes_read=2910239 bytes_retransmit=9 bytes_invalid=0 send_seq=15748 receive_seq=15748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997478 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37261 bytes_read=1522544 bytes_retransmit=9 bytes_invalid=0 send_seq=6151 receive_seq=6151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37747 bytes_read=113654 bytes_retransmit=9 bytes_invalid=0 send_seq=6138 receive_seq=6138 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91839 bytes_read=2350071 bytes_retransmit=0 bytes_invalid=0 send_seq=10697 receive_seq=10697 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998641 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=52.2 th1: temp=52.8 th2: temp=59.8 th3: temp=57.2 sysload=0.01 cputime=431.196 memavail=7391588 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5965.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=26315597 bytes_read=4188163 bytes_retransmit=9 bytes_invalid=0 send_seq=500033 receive_seq=500033 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015954 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37000 bytes_read=115939 bytes_retransmit=0 bytes_invalid=0 send_seq=6138 receive_seq=6138 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997230 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172616 bytes_read=5355609 bytes_retransmit=9 bytes_invalid=0 send_seq=23902 receive_seq=23902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997671 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114912 bytes_read=2910339 bytes_retransmit=9 bytes_invalid=0 send_seq=15749 receive_seq=15749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997697 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37267 bytes_read=1522778 bytes_retransmit=9 bytes_invalid=0 send_seq=6152 receive_seq=6152 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997735 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37753 bytes_read=113670 bytes_retransmit=9 bytes_invalid=0 send_seq=6139 receive_seq=6139 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91845 bytes_read=2350427 bytes_retransmit=0 bytes_invalid=0 send_seq=10698 receive_seq=10698 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998608 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=52.3 th1: temp=52.8 th2: temp=59.8 th3: temp=57.2 sysload=0.01 cputime=431.239 memavail=7391588 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5966.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26315895 bytes_read=4188632 bytes_retransmit=9 bytes_invalid=0 send_seq=500056 receive_seq=500056 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015943 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37006 bytes_read=115968 bytes_retransmit=0 bytes_invalid=0 send_seq=6139 receive_seq=6139 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997260 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172622 bytes_read=5355737 bytes_retransmit=9 bytes_invalid=0 send_seq=23903 receive_seq=23903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997681 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114918 bytes_read=2910453 bytes_retransmit=9 bytes_invalid=0 send_seq=15750 receive_seq=15750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997665 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37273 bytes_read=1523012 bytes_retransmit=9 bytes_invalid=0 send_seq=6153 receive_seq=6153 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997717 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37759 bytes_read=113697 bytes_retransmit=9 bytes_invalid=0 send_seq=6140 receive_seq=6140 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91851 bytes_read=2350783 bytes_retransmit=0 bytes_invalid=0 send_seq=10699 receive_seq=10699 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998623 coil_temp=16.9 refs=0 mcu_temp=20.13 supply_voltage=3.012 th0: temp=52.2 th1: temp=52.8 th2: temp=59.6 th3: temp=57.3 sysload=0.01 cputime=431.284 memavail=7391588 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5967.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26316193 bytes_read=4189057 bytes_retransmit=9 bytes_invalid=0 send_seq=500079 receive_seq=500079 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015937 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37012 bytes_read=115984 bytes_retransmit=0 bytes_invalid=0 send_seq=6140 receive_seq=6140 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997268 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172628 bytes_read=5355851 bytes_retransmit=9 bytes_invalid=0 send_seq=23904 receive_seq=23904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997761 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114924 bytes_read=2910567 bytes_retransmit=9 bytes_invalid=0 send_seq=15751 receive_seq=15751 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997628 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37279 bytes_read=1523306 bytes_retransmit=9 bytes_invalid=0 send_seq=6154 receive_seq=6154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997706 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37765 bytes_read=113713 bytes_retransmit=9 bytes_invalid=0 send_seq=6141 receive_seq=6141 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91857 bytes_read=2351139 bytes_retransmit=0 bytes_invalid=0 send_seq=10700 receive_seq=10700 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998649 coil_temp=16.9 refs=0 mcu_temp=20.14 supply_voltage=3.012 th0: temp=52.1 th1: temp=52.8 th2: temp=59.8 th3: temp=57.2 sysload=0.01 cputime=431.329 memavail=7391140 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5968.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26316491 bytes_read=4189480 bytes_retransmit=9 bytes_invalid=0 send_seq=500102 receive_seq=500102 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015933 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37018 bytes_read=116000 bytes_retransmit=0 bytes_invalid=0 send_seq=6141 receive_seq=6141 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997271 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172634 bytes_read=5355951 bytes_retransmit=9 bytes_invalid=0 send_seq=23905 receive_seq=23905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997735 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114930 bytes_read=2910667 bytes_retransmit=9 bytes_invalid=0 send_seq=15752 receive_seq=15752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997592 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37285 bytes_read=1523555 bytes_retransmit=9 bytes_invalid=0 send_seq=6155 receive_seq=6155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997692 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37771 bytes_read=113729 bytes_retransmit=9 bytes_invalid=0 send_seq=6142 receive_seq=6142 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91863 bytes_read=2351495 bytes_retransmit=0 bytes_invalid=0 send_seq=10701 receive_seq=10701 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998653 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=52.1 th1: temp=52.9 th2: temp=59.7 th3: temp=57.2 sysload=0.01 cputime=431.372 memavail=7391140 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 5969.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26316789 bytes_read=4189931 bytes_retransmit=9 bytes_invalid=0 send_seq=500125 receive_seq=500125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015925 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37024 bytes_read=116016 bytes_retransmit=0 bytes_invalid=0 send_seq=6142 receive_seq=6142 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997282 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172640 bytes_read=5356079 bytes_retransmit=9 bytes_invalid=0 send_seq=23906 receive_seq=23906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997629 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114936 bytes_read=2910795 bytes_retransmit=9 bytes_invalid=0 send_seq=15753 receive_seq=15753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997564 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37291 bytes_read=1523789 bytes_retransmit=9 bytes_invalid=0 send_seq=6156 receive_seq=6156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37777 bytes_read=113745 bytes_retransmit=9 bytes_invalid=0 send_seq=6143 receive_seq=6143 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91869 bytes_read=2351851 bytes_retransmit=0 bytes_invalid=0 send_seq=10702 receive_seq=10702 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998655 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=52.2 th1: temp=52.6 th2: temp=59.8 th3: temp=57.3 sysload=0.01 cputime=431.416 memavail=7391140 print_time=5970.195 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
RatOS:: All requested axes already homed. Skipping homing.
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Probing point (125.000, 250.000, 20.000)
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t0' measurements
toolhead: max_velocity: 600.000000
max_accel: 8379.841000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance testing
Testing frequency 10 Hz
Testing frequency 11 Hz
Testing frequency 12 Hz
Stats 5970.9: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26322510 bytes_read=4190806 bytes_retransmit=9 bytes_invalid=0 send_seq=500238 receive_seq=500238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015914 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37030 bytes_read=116032 bytes_retransmit=0 bytes_invalid=0 send_seq=6143 receive_seq=6143 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997272 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172760 bytes_read=5356779 bytes_retransmit=9 bytes_invalid=0 send_seq=23919 receive_seq=23919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997723 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114942 bytes_read=2910909 bytes_retransmit=9 bytes_invalid=0 send_seq=15754 receive_seq=15754 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37297 bytes_read=1524079 bytes_retransmit=9 bytes_invalid=0 send_seq=6157 receive_seq=6157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37783 bytes_read=113761 bytes_retransmit=9 bytes_invalid=0 send_seq=6144 receive_seq=6144 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91875 bytes_read=2352207 bytes_retransmit=0 bytes_invalid=0 send_seq=10703 receive_seq=10703 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998655 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=52.3 th1: temp=52.8 th2: temp=59.6 th3: temp=57.2 sysload=0.01 cputime=431.624 memavail=7391140 print_time=5996.470 buffer_time=2.958 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 5971.9: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26323161 bytes_read=4191271 bytes_retransmit=9 bytes_invalid=0 send_seq=500266 receive_seq=500266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=0 freq=400015903 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37036 bytes_read=116061 bytes_retransmit=0 bytes_invalid=0 send_seq=6144 receive_seq=6144 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997260 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=172836 bytes_read=5359779 bytes_retransmit=9 bytes_invalid=0 send_seq=23930 receive_seq=23930 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997684 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114948 bytes_read=2911009 bytes_retransmit=9 bytes_invalid=0 send_seq=15755 receive_seq=15755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997514 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37303 bytes_read=1524297 bytes_retransmit=9 bytes_invalid=0 send_seq=6158 receive_seq=6158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37789 bytes_read=113788 bytes_retransmit=9 bytes_invalid=0 send_seq=6145 receive_seq=6145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91881 bytes_read=2352563 bytes_retransmit=0 bytes_invalid=0 send_seq=10704 receive_seq=10704 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998672 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=52.5 th1: temp=53.0 th2: temp=59.7 th3: temp=57.1 sysload=0.01 cputime=431.689 memavail=7391140 print_time=5996.690 buffer_time=2.178 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 13 Hz
Stats 5972.9: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26325620 bytes_read=4191895 bytes_retransmit=9 bytes_invalid=0 send_seq=500323 receive_seq=500323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015898 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37042 bytes_read=116077 bytes_retransmit=0 bytes_invalid=0 send_seq=6145 receive_seq=6145 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997269 toolboard_t0: mcu_awake=0.087 mcu_task_avg=0.000101 mcu_task_stddev=0.000074 bytes_write=172912 bytes_read=5362833 bytes_retransmit=9 bytes_invalid=0 send_seq=23941 receive_seq=23941 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997699 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114954 bytes_read=2911123 bytes_retransmit=9 bytes_invalid=0 send_seq=15756 receive_seq=15756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37309 bytes_read=1524514 bytes_retransmit=9 bytes_invalid=0 send_seq=6159 receive_seq=6159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37795 bytes_read=113804 bytes_retransmit=9 bytes_invalid=0 send_seq=6146 receive_seq=6146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91887 bytes_read=2352919 bytes_retransmit=0 bytes_invalid=0 send_seq=10705 receive_seq=10705 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998672 coil_temp=16.9 refs=0 mcu_temp=20.16 supply_voltage=3.012 th0: temp=52.5 th1: temp=53.0 th2: temp=59.6 th3: temp=57.2 sysload=0.01 cputime=431.764 memavail=7391140 print_time=5997.648 buffer_time=2.134 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 14 Hz
Stats 5973.9: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26327886 bytes_read=4192470 bytes_retransmit=9 bytes_invalid=0 send_seq=500376 receive_seq=500376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015900 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37048 bytes_read=116093 bytes_retransmit=0 bytes_invalid=0 send_seq=6146 receive_seq=6146 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997271 toolboard_t0: mcu_awake=0.087 mcu_task_avg=0.000101 mcu_task_stddev=0.000074 bytes_write=172988 bytes_read=5365948 bytes_retransmit=9 bytes_invalid=0 send_seq=23952 receive_seq=23952 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997760 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114960 bytes_read=2911237 bytes_retransmit=9 bytes_invalid=0 send_seq=15757 receive_seq=15757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997522 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37315 bytes_read=1524803 bytes_retransmit=9 bytes_invalid=0 send_seq=6160 receive_seq=6160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37801 bytes_read=113820 bytes_retransmit=9 bytes_invalid=0 send_seq=6147 receive_seq=6147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91893 bytes_read=2353275 bytes_retransmit=0 bytes_invalid=0 send_seq=10706 receive_seq=10706 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998669 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=52.7 th1: temp=52.9 th2: temp=59.8 th3: temp=57.3 sysload=0.01 cputime=431.840 memavail=7391140 print_time=5998.594 buffer_time=2.079 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 15 Hz
Stats 5974.9: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26330605 bytes_read=4193085 bytes_retransmit=9 bytes_invalid=0 send_seq=500437 receive_seq=500437 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015896 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37054 bytes_read=116109 bytes_retransmit=0 bytes_invalid=0 send_seq=6147 receive_seq=6147 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997264 toolboard_t0: mcu_awake=0.087 mcu_task_avg=0.000101 mcu_task_stddev=0.000074 bytes_write=173064 bytes_read=5369004 bytes_retransmit=9 bytes_invalid=0 send_seq=23963 receive_seq=23963 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997756 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114966 bytes_read=2911351 bytes_retransmit=9 bytes_invalid=0 send_seq=15758 receive_seq=15758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37321 bytes_read=1525021 bytes_retransmit=9 bytes_invalid=0 send_seq=6161 receive_seq=6161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37807 bytes_read=113836 bytes_retransmit=9 bytes_invalid=0 send_seq=6148 receive_seq=6148 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91899 bytes_read=2353631 bytes_retransmit=0 bytes_invalid=0 send_seq=10707 receive_seq=10707 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998659 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=52.6 th1: temp=53.2 th2: temp=59.9 th3: temp=57.4 sysload=0.01 cputime=431.914 memavail=7391140 print_time=5999.530 buffer_time=2.015 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 16 Hz
Stats 5975.9: gcodein=0  mcu: mcu_awake=0.003 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26333742 bytes_read=4193764 bytes_retransmit=9 bytes_invalid=0 send_seq=500505 receive_seq=500505 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=0 freq=400015895 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37060 bytes_read=116125 bytes_retransmit=0 bytes_invalid=0 send_seq=6148 receive_seq=6148 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997278 toolboard_t0: mcu_awake=0.087 mcu_task_avg=0.000101 mcu_task_stddev=0.000074 bytes_write=173140 bytes_read=5372089 bytes_retransmit=9 bytes_invalid=0 send_seq=23974 receive_seq=23974 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997738 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114972 bytes_read=2911465 bytes_retransmit=9 bytes_invalid=0 send_seq=15759 receive_seq=15759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37327 bytes_read=1525239 bytes_retransmit=9 bytes_invalid=0 send_seq=6162 receive_seq=6162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37813 bytes_read=113852 bytes_retransmit=9 bytes_invalid=0 send_seq=6149 receive_seq=6149 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91905 bytes_read=2353987 bytes_retransmit=0 bytes_invalid=0 send_seq=10708 receive_seq=10708 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998657 coil_temp=16.9 refs=0 mcu_temp=20.14 supply_voltage=3.012 th0: temp=52.5 th1: temp=53.1 th2: temp=59.8 th3: temp=57.4 sysload=0.01 cputime=431.994 memavail=7391288 print_time=6000.717 buffer_time=2.202 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 17 Hz
Stats 5976.9: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26336112 bytes_read=4194380 bytes_retransmit=9 bytes_invalid=0 send_seq=500561 receive_seq=500561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015887 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37072 bytes_read=116170 bytes_retransmit=0 bytes_invalid=0 send_seq=6150 receive_seq=6150 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997264 toolboard_t0: mcu_awake=0.087 mcu_task_avg=0.000101 mcu_task_stddev=0.000074 bytes_write=173222 bytes_read=5375161 bytes_retransmit=9 bytes_invalid=0 send_seq=23986 receive_seq=23986 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997707 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114984 bytes_read=2911595 bytes_retransmit=9 bytes_invalid=0 send_seq=15761 receive_seq=15761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37339 bytes_read=1525540 bytes_retransmit=9 bytes_invalid=0 send_seq=6164 receive_seq=6164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37825 bytes_read=113895 bytes_retransmit=9 bytes_invalid=0 send_seq=6151 receive_seq=6151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91917 bytes_read=2354359 bytes_retransmit=0 bytes_invalid=0 send_seq=10710 receive_seq=10710 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998660 coil_temp=16.9 refs=0 mcu_temp=20.14 supply_voltage=3.012 th0: temp=52.8 th1: temp=53.1 th2: temp=59.9 th3: temp=57.4 sysload=0.01 cputime=432.075 memavail=7391164 print_time=6001.640 buffer_time=2.124 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 18 Hz
Stats 5977.9: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26339128 bytes_read=4195020 bytes_retransmit=9 bytes_invalid=0 send_seq=500627 receive_seq=500627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015897 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37078 bytes_read=116186 bytes_retransmit=0 bytes_invalid=0 send_seq=6151 receive_seq=6151 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997273 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=173298 bytes_read=5378234 bytes_retransmit=9 bytes_invalid=0 send_seq=23997 receive_seq=23997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997688 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114990 bytes_read=2911695 bytes_retransmit=9 bytes_invalid=0 send_seq=15762 receive_seq=15762 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997494 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37345 bytes_read=1525774 bytes_retransmit=9 bytes_invalid=0 send_seq=6165 receive_seq=6165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37831 bytes_read=113911 bytes_retransmit=9 bytes_invalid=0 send_seq=6152 receive_seq=6152 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91923 bytes_read=2354715 bytes_retransmit=0 bytes_invalid=0 send_seq=10711 receive_seq=10711 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998689 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=52.7 th1: temp=53.1 th2: temp=60.1 th3: temp=57.6 sysload=0.01 cputime=432.158 memavail=7393480 print_time=6002.557 buffer_time=2.041 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 19 Hz
Stats 5978.9: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26342764 bytes_read=4195739 bytes_retransmit=9 bytes_invalid=0 send_seq=500703 receive_seq=500703 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015893 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37084 bytes_read=116202 bytes_retransmit=0 bytes_invalid=0 send_seq=6152 receive_seq=6152 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997258 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=173374 bytes_read=5381494 bytes_retransmit=9 bytes_invalid=0 send_seq=24008 receive_seq=24008 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997662 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=114996 bytes_read=2911823 bytes_retransmit=9 bytes_invalid=0 send_seq=15763 receive_seq=15763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997481 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37351 bytes_read=1526083 bytes_retransmit=9 bytes_invalid=0 send_seq=6166 receive_seq=6166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37837 bytes_read=113927 bytes_retransmit=9 bytes_invalid=0 send_seq=6153 receive_seq=6153 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91929 bytes_read=2355089 bytes_retransmit=0 bytes_invalid=0 send_seq=10712 receive_seq=10712 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998683 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=52.9 th1: temp=53.1 th2: temp=60.1 th3: temp=57.7 sysload=0.01 cputime=432.334 memavail=7395456 print_time=6003.777 buffer_time=2.196 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 20 Hz
Stats 5979.9: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26345346 bytes_read=4196338 bytes_retransmit=9 bytes_invalid=0 send_seq=500762 receive_seq=500762 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015897 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37090 bytes_read=116218 bytes_retransmit=0 bytes_invalid=0 send_seq=6153 receive_seq=6153 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997250 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=173450 bytes_read=5384552 bytes_retransmit=9 bytes_invalid=0 send_seq=24019 receive_seq=24019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997664 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115002 bytes_read=2911937 bytes_retransmit=9 bytes_invalid=0 send_seq=15764 receive_seq=15764 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997487 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37357 bytes_read=1526317 bytes_retransmit=9 bytes_invalid=0 send_seq=6167 receive_seq=6167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37843 bytes_read=113943 bytes_retransmit=9 bytes_invalid=0 send_seq=6154 receive_seq=6154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91935 bytes_read=2355445 bytes_retransmit=0 bytes_invalid=0 send_seq=10713 receive_seq=10713 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998675 coil_temp=16.9 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=53.1 th1: temp=53.2 th2: temp=60.3 th3: temp=57.8 sysload=0.01 cputime=432.412 memavail=7395456 print_time=6004.702 buffer_time=2.120 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 21 Hz
Stats 5980.9: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=26349179 bytes_read=4197072 bytes_retransmit=9 bytes_invalid=0 send_seq=500841 receive_seq=500841 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015893 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37096 bytes_read=116234 bytes_retransmit=0 bytes_invalid=0 send_seq=6154 receive_seq=6154 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997237 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=173526 bytes_read=5387682 bytes_retransmit=9 bytes_invalid=0 send_seq=24030 receive_seq=24030 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997697 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115008 bytes_read=2912037 bytes_retransmit=9 bytes_invalid=0 send_seq=15765 receive_seq=15765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997474 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37363 bytes_read=1526551 bytes_retransmit=9 bytes_invalid=0 send_seq=6168 receive_seq=6168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37849 bytes_read=113959 bytes_retransmit=9 bytes_invalid=0 send_seq=6155 receive_seq=6155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91941 bytes_read=2355801 bytes_retransmit=0 bytes_invalid=0 send_seq=10714 receive_seq=10714 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998662 coil_temp=16.9 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=53.1 th1: temp=53.3 th2: temp=60.3 th3: temp=57.7 sysload=0.01 cputime=432.494 memavail=7395456 print_time=6005.922 buffer_time=2.339 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 22 Hz
Stats 5981.9: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26352415 bytes_read=4197748 bytes_retransmit=9 bytes_invalid=0 send_seq=500911 receive_seq=500911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=400015887 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37102 bytes_read=116263 bytes_retransmit=0 bytes_invalid=0 send_seq=6155 receive_seq=6155 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997245 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=173602 bytes_read=5390753 bytes_retransmit=9 bytes_invalid=0 send_seq=24041 receive_seq=24041 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997682 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115014 bytes_read=2912165 bytes_retransmit=9 bytes_invalid=0 send_seq=15766 receive_seq=15766 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37369 bytes_read=1526845 bytes_retransmit=9 bytes_invalid=0 send_seq=6169 receive_seq=6169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37855 bytes_read=113986 bytes_retransmit=9 bytes_invalid=0 send_seq=6156 receive_seq=6156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91947 bytes_read=2356157 bytes_retransmit=0 bytes_invalid=0 send_seq=10715 receive_seq=10715 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998662 coil_temp=16.9 refs=0 mcu_temp=20.18 supply_voltage=3.011 th0: temp=53.2 th1: temp=53.4 th2: temp=60.5 th3: temp=57.9 sysload=0.01 cputime=432.574 memavail=7395456 print_time=6006.788 buffer_time=2.204 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 23 Hz
Stats 5982.9: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26355341 bytes_read=4198383 bytes_retransmit=9 bytes_invalid=0 send_seq=500976 receive_seq=500976 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015886 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37108 bytes_read=116279 bytes_retransmit=0 bytes_invalid=0 send_seq=6156 receive_seq=6156 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997239 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=173678 bytes_read=5393826 bytes_retransmit=9 bytes_invalid=0 send_seq=24052 receive_seq=24052 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997758 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115020 bytes_read=2912265 bytes_retransmit=9 bytes_invalid=0 send_seq=15767 receive_seq=15767 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997502 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37375 bytes_read=1527079 bytes_retransmit=9 bytes_invalid=0 send_seq=6170 receive_seq=6170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37861 bytes_read=114002 bytes_retransmit=9 bytes_invalid=0 send_seq=6157 receive_seq=6157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91953 bytes_read=2356513 bytes_retransmit=0 bytes_invalid=0 send_seq=10716 receive_seq=10716 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998662 coil_temp=16.9 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=53.4 th1: temp=53.2 th2: temp=60.4 th3: temp=57.9 sysload=0.01 cputime=432.655 memavail=7395456 print_time=6007.730 buffer_time=2.146 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 24 Hz
Stats 5983.9: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26358714 bytes_read=4199082 bytes_retransmit=9 bytes_invalid=0 send_seq=501048 receive_seq=501048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015889 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37114 bytes_read=116295 bytes_retransmit=0 bytes_invalid=0 send_seq=6157 receive_seq=6157 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997240 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=173754 bytes_read=5396896 bytes_retransmit=9 bytes_invalid=0 send_seq=24063 receive_seq=24063 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997747 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115026 bytes_read=2912365 bytes_retransmit=9 bytes_invalid=0 send_seq=15768 receive_seq=15768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37381 bytes_read=1527328 bytes_retransmit=9 bytes_invalid=0 send_seq=6171 receive_seq=6171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37867 bytes_read=114018 bytes_retransmit=9 bytes_invalid=0 send_seq=6158 receive_seq=6158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91959 bytes_read=2356869 bytes_retransmit=0 bytes_invalid=0 send_seq=10717 receive_seq=10717 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998715 coil_temp=16.9 refs=0 mcu_temp=20.17 supply_voltage=3.012 th0: temp=53.5 th1: temp=53.6 th2: temp=60.5 th3: temp=58.0 sysload=0.01 cputime=432.737 memavail=7397464 print_time=6008.590 buffer_time=2.005 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 25 Hz
Stats 5984.9: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26362895 bytes_read=4199817 bytes_retransmit=9 bytes_invalid=0 send_seq=501133 receive_seq=501133 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015887 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37120 bytes_read=116311 bytes_retransmit=0 bytes_invalid=0 send_seq=6158 receive_seq=6158 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997236 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=173830 bytes_read=5399967 bytes_retransmit=9 bytes_invalid=0 send_seq=24074 receive_seq=24074 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997773 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115032 bytes_read=2912507 bytes_retransmit=9 bytes_invalid=0 send_seq=15769 receive_seq=15769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37387 bytes_read=1527622 bytes_retransmit=9 bytes_invalid=0 send_seq=6172 receive_seq=6172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37873 bytes_read=114034 bytes_retransmit=9 bytes_invalid=0 send_seq=6159 receive_seq=6159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91965 bytes_read=2357225 bytes_retransmit=0 bytes_invalid=0 send_seq=10718 receive_seq=10718 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998740 coil_temp=16.9 refs=0 mcu_temp=20.16 supply_voltage=3.012 th0: temp=53.6 th1: temp=53.6 th2: temp=60.4 th3: temp=58.0 sysload=0.01 cputime=432.823 memavail=7397464 print_time=6009.805 buffer_time=2.220 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 26 Hz
Stats 5985.9: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26365991 bytes_read=4200467 bytes_retransmit=9 bytes_invalid=0 send_seq=501201 receive_seq=501201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=0 freq=400015884 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37126 bytes_read=116327 bytes_retransmit=0 bytes_invalid=0 send_seq=6159 receive_seq=6159 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997244 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=173906 bytes_read=5403026 bytes_retransmit=9 bytes_invalid=0 send_seq=24085 receive_seq=24085 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000239 adj=63997882 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115038 bytes_read=2912607 bytes_retransmit=9 bytes_invalid=0 send_seq=15770 receive_seq=15770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37393 bytes_read=1527856 bytes_retransmit=9 bytes_invalid=0 send_seq=6173 receive_seq=6173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37879 bytes_read=114050 bytes_retransmit=9 bytes_invalid=0 send_seq=6160 receive_seq=6160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91971 bytes_read=2357581 bytes_retransmit=0 bytes_invalid=0 send_seq=10719 receive_seq=10719 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998710 coil_temp=16.9 refs=0 mcu_temp=20.16 supply_voltage=3.012 th0: temp=53.6 th1: temp=53.4 th2: temp=60.6 th3: temp=58.1 sysload=0.01 cputime=432.904 memavail=7397464 print_time=6010.751 buffer_time=2.166 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 27 Hz
Stats 5986.9: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26369502 bytes_read=4201192 bytes_retransmit=9 bytes_invalid=0 send_seq=501275 receive_seq=501275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015884 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37132 bytes_read=116356 bytes_retransmit=0 bytes_invalid=0 send_seq=6160 receive_seq=6160 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997247 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=173982 bytes_read=5406098 bytes_retransmit=9 bytes_invalid=0 send_seq=24096 receive_seq=24096 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997842 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115044 bytes_read=2912707 bytes_retransmit=9 bytes_invalid=0 send_seq=15771 receive_seq=15771 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997514 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37399 bytes_read=1528090 bytes_retransmit=9 bytes_invalid=0 send_seq=6174 receive_seq=6174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37885 bytes_read=114077 bytes_retransmit=9 bytes_invalid=0 send_seq=6161 receive_seq=6161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91977 bytes_read=2357937 bytes_retransmit=0 bytes_invalid=0 send_seq=10720 receive_seq=10720 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998707 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=53.7 th1: temp=53.2 th2: temp=60.5 th3: temp=58.1 sysload=0.01 cputime=432.983 memavail=7397464 print_time=6011.646 buffer_time=2.061 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 28 Hz
Stats 5987.9: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26373154 bytes_read=4201877 bytes_retransmit=9 bytes_invalid=0 send_seq=501350 receive_seq=501350 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015876 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37138 bytes_read=116372 bytes_retransmit=0 bytes_invalid=0 send_seq=6161 receive_seq=6161 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997246 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=174058 bytes_read=5409185 bytes_retransmit=9 bytes_invalid=0 send_seq=24107 receive_seq=24107 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997789 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115050 bytes_read=2912835 bytes_retransmit=9 bytes_invalid=0 send_seq=15772 receive_seq=15772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997517 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37405 bytes_read=1528384 bytes_retransmit=9 bytes_invalid=0 send_seq=6175 receive_seq=6175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37891 bytes_read=114093 bytes_retransmit=9 bytes_invalid=0 send_seq=6162 receive_seq=6162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91983 bytes_read=2358293 bytes_retransmit=0 bytes_invalid=0 send_seq=10721 receive_seq=10721 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998699 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=53.7 th1: temp=53.6 th2: temp=60.8 th3: temp=58.1 sysload=0.01 cputime=433.067 memavail=7395728 print_time=6012.610 buffer_time=2.024 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 29 Hz
Stats 5988.9: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26377606 bytes_read=4202637 bytes_retransmit=9 bytes_invalid=0 send_seq=501440 receive_seq=501440 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=0 freq=400015903 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37144 bytes_read=116388 bytes_retransmit=0 bytes_invalid=0 send_seq=6162 receive_seq=6162 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997246 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=174134 bytes_read=5412303 bytes_retransmit=9 bytes_invalid=0 send_seq=24118 receive_seq=24118 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997777 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115056 bytes_read=2912935 bytes_retransmit=9 bytes_invalid=0 send_seq=15773 receive_seq=15773 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37411 bytes_read=1528633 bytes_retransmit=9 bytes_invalid=0 send_seq=6176 receive_seq=6176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37897 bytes_read=114109 bytes_retransmit=9 bytes_invalid=0 send_seq=6163 receive_seq=6163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91989 bytes_read=2358649 bytes_retransmit=0 bytes_invalid=0 send_seq=10722 receive_seq=10722 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998697 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=53.7 th1: temp=53.4 th2: temp=60.6 th3: temp=58.2 sysload=0.01 cputime=433.155 memavail=7395728 print_time=6013.812 buffer_time=2.226 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 30 Hz
Stats 5989.9: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26380827 bytes_read=4203319 bytes_retransmit=9 bytes_invalid=0 send_seq=501509 receive_seq=501509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015907 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37150 bytes_read=116404 bytes_retransmit=0 bytes_invalid=0 send_seq=6163 receive_seq=6163 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997207 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=174210 bytes_read=5415373 bytes_retransmit=9 bytes_invalid=0 send_seq=24129 receive_seq=24129 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997674 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115062 bytes_read=2913049 bytes_retransmit=9 bytes_invalid=0 send_seq=15774 receive_seq=15774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37417 bytes_read=1528867 bytes_retransmit=9 bytes_invalid=0 send_seq=6177 receive_seq=6177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37903 bytes_read=114125 bytes_retransmit=9 bytes_invalid=0 send_seq=6164 receive_seq=6164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=91995 bytes_read=2359005 bytes_retransmit=0 bytes_invalid=0 send_seq=10723 receive_seq=10723 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998661 coil_temp=16.9 refs=0 mcu_temp=20.15 supply_voltage=3.012 th0: temp=53.9 th1: temp=53.5 th2: temp=60.7 th3: temp=58.2 sysload=0.01 cputime=433.235 memavail=7395756 print_time=6014.667 buffer_time=2.080 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 31 Hz
Stats 5990.9: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26384887 bytes_read=4204034 bytes_retransmit=9 bytes_invalid=0 send_seq=501591 receive_seq=501591 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015907 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37156 bytes_read=116420 bytes_retransmit=0 bytes_invalid=0 send_seq=6164 receive_seq=6164 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997225 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=174286 bytes_read=5418446 bytes_retransmit=9 bytes_invalid=0 send_seq=24140 receive_seq=24140 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997643 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115068 bytes_read=2913177 bytes_retransmit=9 bytes_invalid=0 send_seq=15775 receive_seq=15775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997507 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37423 bytes_read=1529161 bytes_retransmit=9 bytes_invalid=0 send_seq=6178 receive_seq=6178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997616 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37909 bytes_read=114141 bytes_retransmit=9 bytes_invalid=0 send_seq=6165 receive_seq=6165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999429 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92001 bytes_read=2359361 bytes_retransmit=0 bytes_invalid=0 send_seq=10724 receive_seq=10724 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998654 coil_temp=16.9 refs=0 mcu_temp=20.16 supply_voltage=3.012 th0: temp=54.2 th1: temp=53.3 th2: temp=60.8 th3: temp=58.3 sysload=0.01 cputime=433.316 memavail=7395756 print_time=6015.649 buffer_time=2.062 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 32 Hz
Stats 5991.9: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26389445 bytes_read=4204815 bytes_retransmit=9 bytes_invalid=0 send_seq=501682 receive_seq=501682 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015920 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37162 bytes_read=116449 bytes_retransmit=0 bytes_invalid=0 send_seq=6165 receive_seq=6165 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997264 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=174362 bytes_read=5421503 bytes_retransmit=9 bytes_invalid=0 send_seq=24151 receive_seq=24151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997682 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115074 bytes_read=2913277 bytes_retransmit=9 bytes_invalid=0 send_seq=15776 receive_seq=15776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997499 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37429 bytes_read=1529395 bytes_retransmit=9 bytes_invalid=0 send_seq=6179 receive_seq=6179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37915 bytes_read=114168 bytes_retransmit=9 bytes_invalid=0 send_seq=6166 receive_seq=6166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92007 bytes_read=2359717 bytes_retransmit=0 bytes_invalid=0 send_seq=10725 receive_seq=10725 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998647 coil_temp=16.9 refs=0 mcu_temp=20.17 supply_voltage=3.012 th0: temp=54.0 th1: temp=53.7 th2: temp=60.9 th3: temp=58.3 sysload=0.01 cputime=433.404 memavail=7395756 print_time=6016.831 buffer_time=2.244 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 33 Hz
Stats 5992.9: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26392764 bytes_read=4205509 bytes_retransmit=9 bytes_invalid=0 send_seq=501753 receive_seq=501753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015942 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37168 bytes_read=116465 bytes_retransmit=0 bytes_invalid=0 send_seq=6166 receive_seq=6166 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997304 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=174438 bytes_read=5424590 bytes_retransmit=9 bytes_invalid=0 send_seq=24162 receive_seq=24162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997708 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115080 bytes_read=2913377 bytes_retransmit=9 bytes_invalid=0 send_seq=15777 receive_seq=15777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997479 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37435 bytes_read=1529629 bytes_retransmit=9 bytes_invalid=0 send_seq=6180 receive_seq=6180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997615 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37921 bytes_read=114184 bytes_retransmit=9 bytes_invalid=0 send_seq=6167 receive_seq=6167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999428 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92013 bytes_read=2360073 bytes_retransmit=0 bytes_invalid=0 send_seq=10726 receive_seq=10726 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998633 coil_temp=16.9 refs=0 mcu_temp=20.18 supply_voltage=3.012 th0: temp=54.2 th1: temp=53.7 th2: temp=60.9 th3: temp=58.4 sysload=0.01 cputime=433.489 memavail=7395756 print_time=6017.706 buffer_time=2.118 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 34 Hz
Stats 5994.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26397053 bytes_read=4206254 bytes_retransmit=9 bytes_invalid=0 send_seq=501840 receive_seq=501840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015961 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37174 bytes_read=116481 bytes_retransmit=0 bytes_invalid=0 send_seq=6167 receive_seq=6167 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997261 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=174514 bytes_read=5427661 bytes_retransmit=9 bytes_invalid=0 send_seq=24173 receive_seq=24173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997662 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115086 bytes_read=2913505 bytes_retransmit=9 bytes_invalid=0 send_seq=15778 receive_seq=15778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997432 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37441 bytes_read=1529938 bytes_retransmit=9 bytes_invalid=0 send_seq=6181 receive_seq=6181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997583 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37927 bytes_read=114200 bytes_retransmit=9 bytes_invalid=0 send_seq=6168 receive_seq=6168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92019 bytes_read=2360429 bytes_retransmit=0 bytes_invalid=0 send_seq=10727 receive_seq=10727 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998605 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=54.2 th1: temp=53.7 th2: temp=60.9 th3: temp=58.4 sysload=0.01 cputime=433.575 memavail=7395768 print_time=6018.667 buffer_time=2.079 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 35 Hz
Stats 5995.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26402039 bytes_read=4207054 bytes_retransmit=9 bytes_invalid=0 send_seq=501938 receive_seq=501938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=8 freq=400016011 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37180 bytes_read=116497 bytes_retransmit=0 bytes_invalid=0 send_seq=6168 receive_seq=6168 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997219 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=174583 bytes_read=5430696 bytes_retransmit=9 bytes_invalid=0 send_seq=24183 receive_seq=24183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997614 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115092 bytes_read=2913619 bytes_retransmit=9 bytes_invalid=0 send_seq=15779 receive_seq=15779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997437 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37447 bytes_read=1530172 bytes_retransmit=9 bytes_invalid=0 send_seq=6182 receive_seq=6182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997560 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37933 bytes_read=114216 bytes_retransmit=9 bytes_invalid=0 send_seq=6169 receive_seq=6169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92025 bytes_read=2360785 bytes_retransmit=0 bytes_invalid=0 send_seq=10728 receive_seq=10728 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998585 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=54.0 th1: temp=53.7 th2: temp=61.0 th3: temp=58.4 sysload=0.01 cputime=433.667 memavail=7395768 print_time=6019.868 buffer_time=2.279 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 36 Hz
Stats 5996.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26405401 bytes_read=4207753 bytes_retransmit=9 bytes_invalid=0 send_seq=502010 receive_seq=502010 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400016007 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37186 bytes_read=116513 bytes_retransmit=0 bytes_invalid=0 send_seq=6169 receive_seq=6169 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997141 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=174659 bytes_read=5433766 bytes_retransmit=9 bytes_invalid=0 send_seq=24194 receive_seq=24194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000244 adj=63997556 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115098 bytes_read=2913719 bytes_retransmit=9 bytes_invalid=0 send_seq=15780 receive_seq=15780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997364 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37453 bytes_read=1530406 bytes_retransmit=9 bytes_invalid=0 send_seq=6183 receive_seq=6183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997524 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37939 bytes_read=114232 bytes_retransmit=9 bytes_invalid=0 send_seq=6170 receive_seq=6170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999411 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92031 bytes_read=2361141 bytes_retransmit=0 bytes_invalid=0 send_seq=10729 receive_seq=10729 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998554 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=54.0 th1: temp=53.6 th2: temp=60.9 th3: temp=58.4 sysload=0.01 cputime=433.761 memavail=7396892 print_time=6020.759 buffer_time=2.170 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 37 Hz
Stats 5997.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26409983 bytes_read=4208524 bytes_retransmit=9 bytes_invalid=0 send_seq=502099 receive_seq=502099 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=400015997 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37192 bytes_read=116542 bytes_retransmit=0 bytes_invalid=0 send_seq=6170 receive_seq=6170 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997153 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=174735 bytes_read=5436896 bytes_retransmit=9 bytes_invalid=0 send_seq=24205 receive_seq=24205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000251 adj=63997652 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115104 bytes_read=2913847 bytes_retransmit=9 bytes_invalid=0 send_seq=15781 receive_seq=15781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997383 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37459 bytes_read=1530700 bytes_retransmit=9 bytes_invalid=0 send_seq=6184 receive_seq=6184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997553 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37945 bytes_read=114259 bytes_retransmit=9 bytes_invalid=0 send_seq=6171 receive_seq=6171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999414 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92037 bytes_read=2361493 bytes_retransmit=0 bytes_invalid=0 send_seq=10730 receive_seq=10730 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998569 coil_temp=16.9 refs=0 mcu_temp=20.18 supply_voltage=3.012 th0: temp=54.3 th1: temp=53.6 th2: temp=61.3 th3: temp=58.6 sysload=0.01 cputime=433.849 memavail=7396892 print_time=6021.695 buffer_time=2.105 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 38 Hz
Stats 5998.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26414512 bytes_read=4209279 bytes_retransmit=9 bytes_invalid=0 send_seq=502188 receive_seq=502188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=43 upcoming_bytes=587 freq=400016002 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37198 bytes_read=116558 bytes_retransmit=0 bytes_invalid=0 send_seq=6171 receive_seq=6171 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999243 adj=49997188 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=174811 bytes_read=5439971 bytes_retransmit=9 bytes_invalid=0 send_seq=24216 receive_seq=24216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000257 adj=63997768 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115110 bytes_read=2913947 bytes_retransmit=9 bytes_invalid=0 send_seq=15782 receive_seq=15782 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997420 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37465 bytes_read=1530934 bytes_retransmit=9 bytes_invalid=0 send_seq=6185 receive_seq=6185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37951 bytes_read=114275 bytes_retransmit=9 bytes_invalid=0 send_seq=6172 receive_seq=6172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999420 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92043 bytes_read=2361838 bytes_retransmit=0 bytes_invalid=0 send_seq=10731 receive_seq=10731 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998589 coil_temp=16.9 refs=0 mcu_temp=20.17 supply_voltage=3.012 th0: temp=54.3 th1: temp=53.6 th2: temp=61.1 th3: temp=58.7 sysload=0.01 cputime=433.947 memavail=7397268 print_time=6022.893 buffer_time=2.303 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 39 Hz
Stats 5999.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26418633 bytes_read=4210023 bytes_retransmit=9 bytes_invalid=0 send_seq=502269 receive_seq=502269 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=0 freq=400016001 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37204 bytes_read=116574 bytes_retransmit=0 bytes_invalid=0 send_seq=6172 receive_seq=6172 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997191 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=174887 bytes_read=5443043 bytes_retransmit=9 bytes_invalid=0 send_seq=24227 receive_seq=24227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000259 adj=63997807 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115116 bytes_read=2914047 bytes_retransmit=9 bytes_invalid=0 send_seq=15783 receive_seq=15783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997434 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37471 bytes_read=1531183 bytes_retransmit=9 bytes_invalid=0 send_seq=6186 receive_seq=6186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37957 bytes_read=114291 bytes_retransmit=9 bytes_invalid=0 send_seq=6173 receive_seq=6173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92049 bytes_read=2362182 bytes_retransmit=0 bytes_invalid=0 send_seq=10732 receive_seq=10732 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998640 coil_temp=16.9 refs=0 mcu_temp=20.18 supply_voltage=3.012 th0: temp=54.2 th1: temp=53.7 th2: temp=61.1 th3: temp=58.5 sysload=0.01 cputime=434.038 memavail=7397016 print_time=6023.785 buffer_time=2.195 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 40 Hz
Stats 6000.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26423099 bytes_read=4210778 bytes_retransmit=9 bytes_invalid=0 send_seq=502358 receive_seq=502358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=175 freq=400016020 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37210 bytes_read=116590 bytes_retransmit=0 bytes_invalid=0 send_seq=6173 receive_seq=6173 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997190 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=174963 bytes_read=5446113 bytes_retransmit=9 bytes_invalid=0 send_seq=24238 receive_seq=24238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000263 adj=63997822 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115122 bytes_read=2914189 bytes_retransmit=9 bytes_invalid=0 send_seq=15784 receive_seq=15784 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997431 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37477 bytes_read=1531477 bytes_retransmit=9 bytes_invalid=0 send_seq=6187 receive_seq=6187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37963 bytes_read=114307 bytes_retransmit=9 bytes_invalid=0 send_seq=6174 receive_seq=6174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92055 bytes_read=2362527 bytes_retransmit=0 bytes_invalid=0 send_seq=10733 receive_seq=10733 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998641 coil_temp=16.9 refs=0 mcu_temp=20.17 supply_voltage=3.012 th0: temp=54.3 th1: temp=53.7 th2: temp=61.0 th3: temp=58.5 sysload=0.00 cputime=434.125 memavail=7397016 print_time=6024.700 buffer_time=2.110 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 41 Hz
Stats 6001.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26427058 bytes_read=4211476 bytes_retransmit=9 bytes_invalid=0 send_seq=502436 receive_seq=502436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400016023 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37216 bytes_read=116606 bytes_retransmit=0 bytes_invalid=0 send_seq=6174 receive_seq=6174 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997157 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=175039 bytes_read=5449170 bytes_retransmit=9 bytes_invalid=0 send_seq=24249 receive_seq=24249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000259 adj=63997814 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115128 bytes_read=2914289 bytes_retransmit=9 bytes_invalid=0 send_seq=15785 receive_seq=15785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997392 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37483 bytes_read=1531711 bytes_retransmit=9 bytes_invalid=0 send_seq=6188 receive_seq=6188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997604 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37969 bytes_read=114323 bytes_retransmit=9 bytes_invalid=0 send_seq=6175 receive_seq=6175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92061 bytes_read=2362872 bytes_retransmit=0 bytes_invalid=0 send_seq=10734 receive_seq=10734 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998623 coil_temp=16.9 refs=0 mcu_temp=20.16 supply_voltage=3.012 th0: temp=54.3 th1: temp=53.8 th2: temp=61.2 th3: temp=58.5 sysload=0.00 cputime=434.213 memavail=7397016 print_time=6025.596 buffer_time=2.005 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 42 Hz
Stats 6002.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26432471 bytes_read=4212348 bytes_retransmit=9 bytes_invalid=0 send_seq=502540 receive_seq=502540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=196 freq=400016011 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37222 bytes_read=116635 bytes_retransmit=0 bytes_invalid=0 send_seq=6175 receive_seq=6175 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997148 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=175115 bytes_read=5452241 bytes_retransmit=9 bytes_invalid=0 send_seq=24260 receive_seq=24260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000255 adj=63997744 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115134 bytes_read=2914389 bytes_retransmit=9 bytes_invalid=0 send_seq=15786 receive_seq=15786 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997394 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37489 bytes_read=1531945 bytes_retransmit=9 bytes_invalid=0 send_seq=6189 receive_seq=6189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997595 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37975 bytes_read=114350 bytes_retransmit=9 bytes_invalid=0 send_seq=6176 receive_seq=6176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92067 bytes_read=2363217 bytes_retransmit=0 bytes_invalid=0 send_seq=10735 receive_seq=10735 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998615 coil_temp=16.9 refs=0 mcu_temp=20.17 supply_voltage=3.012 th0: temp=54.3 th1: temp=54.0 th2: temp=61.1 th3: temp=58.6 sysload=0.00 cputime=434.314 memavail=7397328 print_time=6026.807 buffer_time=2.216 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 43 Hz
Stats 6003.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26436588 bytes_read=4213063 bytes_retransmit=9 bytes_invalid=0 send_seq=502621 receive_seq=502621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=873 freq=400016005 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37228 bytes_read=116651 bytes_retransmit=0 bytes_invalid=0 send_seq=6176 receive_seq=6176 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997212 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=175191 bytes_read=5455329 bytes_retransmit=9 bytes_invalid=0 send_seq=24271 receive_seq=24271 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000251 adj=63997703 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115140 bytes_read=2914517 bytes_retransmit=9 bytes_invalid=0 send_seq=15787 receive_seq=15787 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997440 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37495 bytes_read=1532239 bytes_retransmit=9 bytes_invalid=0 send_seq=6190 receive_seq=6190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997626 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37981 bytes_read=114366 bytes_retransmit=9 bytes_invalid=0 send_seq=6177 receive_seq=6177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92073 bytes_read=2363562 bytes_retransmit=0 bytes_invalid=0 send_seq=10736 receive_seq=10736 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998630 coil_temp=16.9 refs=0 mcu_temp=20.18 supply_voltage=3.012 th0: temp=54.5 th1: temp=53.8 th2: temp=61.1 th3: temp=58.6 sysload=0.00 cputime=434.405 memavail=7397328 print_time=6027.728 buffer_time=2.136 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 44 Hz
Stats 6004.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26441334 bytes_read=4213828 bytes_retransmit=9 bytes_invalid=0 send_seq=502712 receive_seq=502712 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=0 freq=400016043 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37234 bytes_read=116667 bytes_retransmit=0 bytes_invalid=0 send_seq=6177 receive_seq=6177 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997219 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=175267 bytes_read=5458444 bytes_retransmit=9 bytes_invalid=0 send_seq=24282 receive_seq=24282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000247 adj=63997664 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115146 bytes_read=2914617 bytes_retransmit=9 bytes_invalid=0 send_seq=15788 receive_seq=15788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997450 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37501 bytes_read=1532488 bytes_retransmit=9 bytes_invalid=0 send_seq=6191 receive_seq=6191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997632 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37987 bytes_read=114382 bytes_retransmit=9 bytes_invalid=0 send_seq=6178 receive_seq=6178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92079 bytes_read=2363907 bytes_retransmit=0 bytes_invalid=0 send_seq=10737 receive_seq=10737 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998631 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=54.8 th1: temp=53.8 th2: temp=61.1 th3: temp=58.6 sysload=0.00 cputime=434.500 memavail=7397076 print_time=6028.613 buffer_time=2.020 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 45 Hz
Stats 6005.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26446567 bytes_read=4214662 bytes_retransmit=9 bytes_invalid=0 send_seq=502811 receive_seq=502811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=532 freq=400016258 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37240 bytes_read=116683 bytes_retransmit=0 bytes_invalid=0 send_seq=6178 receive_seq=6178 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997154 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=175343 bytes_read=5461515 bytes_retransmit=9 bytes_invalid=0 send_seq=24293 receive_seq=24293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000243 adj=63997538 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115152 bytes_read=2914731 bytes_retransmit=9 bytes_invalid=0 send_seq=15789 receive_seq=15789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997363 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37507 bytes_read=1532722 bytes_retransmit=9 bytes_invalid=0 send_seq=6192 receive_seq=6192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37993 bytes_read=114398 bytes_retransmit=9 bytes_invalid=0 send_seq=6179 receive_seq=6179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999416 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92085 bytes_read=2364252 bytes_retransmit=0 bytes_invalid=0 send_seq=10738 receive_seq=10738 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998587 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=54.6 th1: temp=53.4 th2: temp=61.1 th3: temp=58.7 sysload=0.00 cputime=434.607 memavail=7397076 print_time=6029.810 buffer_time=2.217 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 46 Hz
Stats 6006.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=26450765 bytes_read=4215382 bytes_retransmit=9 bytes_invalid=0 send_seq=502893 receive_seq=502893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=1198 freq=400016250 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37246 bytes_read=116699 bytes_retransmit=0 bytes_invalid=0 send_seq=6179 receive_seq=6179 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49996844 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=175419 bytes_read=5464585 bytes_retransmit=9 bytes_invalid=0 send_seq=24304 receive_seq=24304 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000244 adj=63997119 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115158 bytes_read=2914859 bytes_retransmit=9 bytes_invalid=0 send_seq=15790 receive_seq=15790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63996990 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37513 bytes_read=1533016 bytes_retransmit=9 bytes_invalid=0 send_seq=6193 receive_seq=6193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997339 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=37999 bytes_read=114414 bytes_retransmit=9 bytes_invalid=0 send_seq=6180 receive_seq=6180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999343 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92091 bytes_read=2364608 bytes_retransmit=0 bytes_invalid=0 send_seq=10739 receive_seq=10739 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998393 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=54.5 th1: temp=53.9 th2: temp=61.1 th3: temp=58.5 sysload=0.00 cputime=434.702 memavail=7397076 print_time=6030.747 buffer_time=2.153 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 47 Hz
Stats 6007.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26455919 bytes_read=4216188 bytes_retransmit=9 bytes_invalid=0 send_seq=502989 receive_seq=502989 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=29 upcoming_bytes=0 freq=400016222 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=37252 bytes_read=116728 bytes_retransmit=0 bytes_invalid=0 send_seq=6180 receive_seq=6180 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49996906 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=175495 bytes_read=5467642 bytes_retransmit=9 bytes_invalid=0 send_seq=24315 receive_seq=24315 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000252 adj=63997219 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115164 bytes_read=2914959 bytes_retransmit=9 bytes_invalid=0 send_seq=15791 receive_seq=15791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997069 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37519 bytes_read=1533250 bytes_retransmit=9 bytes_invalid=0 send_seq=6194 receive_seq=6194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997387 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38005 bytes_read=114441 bytes_retransmit=9 bytes_invalid=0 send_seq=6181 receive_seq=6181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999357 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92097 bytes_read=2364964 bytes_retransmit=0 bytes_invalid=0 send_seq=10740 receive_seq=10740 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998477 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=54.7 th1: temp=53.7 th2: temp=61.2 th3: temp=58.7 sysload=0.00 cputime=434.801 memavail=7397076 print_time=6031.638 buffer_time=2.043 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 48 Hz
Stats 6008.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26461002 bytes_read=4217017 bytes_retransmit=9 bytes_invalid=0 send_seq=503087 receive_seq=503087 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=778 freq=400016204 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=37258 bytes_read=116744 bytes_retransmit=0 bytes_invalid=0 send_seq=6181 receive_seq=6181 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49996985 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=175571 bytes_read=5470731 bytes_retransmit=9 bytes_invalid=0 send_seq=24326 receive_seq=24326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000252 adj=63997436 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115170 bytes_read=2915059 bytes_retransmit=9 bytes_invalid=0 send_seq=15792 receive_seq=15792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997170 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37525 bytes_read=1533484 bytes_retransmit=9 bytes_invalid=0 send_seq=6195 receive_seq=6195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997447 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38011 bytes_read=114457 bytes_retransmit=9 bytes_invalid=0 send_seq=6182 receive_seq=6182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999378 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92103 bytes_read=2365320 bytes_retransmit=0 bytes_invalid=0 send_seq=10741 receive_seq=10741 retransmit_seq=0 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998527 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=54.8 th1: temp=54.0 th2: temp=61.1 th3: temp=58.6 sysload=0.00 cputime=434.914 memavail=7395252 print_time=6032.843 buffer_time=2.248 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 49 Hz
Stats 6009.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26465267 bytes_read=4217737 bytes_retransmit=9 bytes_invalid=0 send_seq=503169 receive_seq=503169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=1530 freq=400016187 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=37264 bytes_read=116760 bytes_retransmit=0 bytes_invalid=0 send_seq=6182 receive_seq=6182 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997063 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=175647 bytes_read=5473801 bytes_retransmit=9 bytes_invalid=0 send_seq=24337 receive_seq=24337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000248 adj=63997537 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115176 bytes_read=2915187 bytes_retransmit=9 bytes_invalid=0 send_seq=15793 receive_seq=15793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997287 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37531 bytes_read=1533793 bytes_retransmit=9 bytes_invalid=0 send_seq=6196 receive_seq=6196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997523 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38017 bytes_read=114473 bytes_retransmit=9 bytes_invalid=0 send_seq=6183 receive_seq=6183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999402 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92109 bytes_read=2365676 bytes_retransmit=0 bytes_invalid=0 send_seq=10742 receive_seq=10742 retransmit_seq=0 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998580 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=54.7 th1: temp=54.0 th2: temp=61.3 th3: temp=58.7 sysload=0.00 cputime=435.009 memavail=7395444 print_time=6033.758 buffer_time=2.162 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 50 Hz
Stats 6010.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26470614 bytes_read=4218547 bytes_retransmit=9 bytes_invalid=0 send_seq=503269 receive_seq=503269 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=378 freq=400016163 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=37270 bytes_read=116776 bytes_retransmit=0 bytes_invalid=0 send_seq=6183 receive_seq=6183 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997106 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=175723 bytes_read=5476858 bytes_retransmit=9 bytes_invalid=0 send_seq=24348 receive_seq=24348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000244 adj=63997534 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115182 bytes_read=2915287 bytes_retransmit=9 bytes_invalid=0 send_seq=15794 receive_seq=15794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997336 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37537 bytes_read=1534027 bytes_retransmit=9 bytes_invalid=0 send_seq=6197 receive_seq=6197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997569 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38023 bytes_read=114489 bytes_retransmit=9 bytes_invalid=0 send_seq=6184 receive_seq=6184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999410 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92115 bytes_read=2366032 bytes_retransmit=0 bytes_invalid=0 send_seq=10743 receive_seq=10743 retransmit_seq=0 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998604 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=54.7 th1: temp=53.8 th2: temp=61.2 th3: temp=58.8 sysload=0.00 cputime=435.108 memavail=7395444 print_time=6034.656 buffer_time=2.060 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 51 Hz
Stats 6011.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26475874 bytes_read=4219376 bytes_retransmit=9 bytes_invalid=0 send_seq=503367 receive_seq=503367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=982 freq=400016158 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=37276 bytes_read=116792 bytes_retransmit=0 bytes_invalid=0 send_seq=6184 receive_seq=6184 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997151 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=175799 bytes_read=5479930 bytes_retransmit=9 bytes_invalid=0 send_seq=24359 receive_seq=24359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000241 adj=63997547 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115188 bytes_read=2915401 bytes_retransmit=9 bytes_invalid=0 send_seq=15795 receive_seq=15795 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997393 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37543 bytes_read=1534261 bytes_retransmit=9 bytes_invalid=0 send_seq=6198 receive_seq=6198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997608 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38029 bytes_read=114505 bytes_retransmit=9 bytes_invalid=0 send_seq=6185 receive_seq=6185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999420 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92121 bytes_read=2366388 bytes_retransmit=0 bytes_invalid=0 send_seq=10744 receive_seq=10744 retransmit_seq=0 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998621 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=54.6 th1: temp=53.9 th2: temp=61.3 th3: temp=58.8 sysload=0.00 cputime=435.216 memavail=7395512 print_time=6035.844 buffer_time=2.247 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 52 Hz
Stats 6012.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26480358 bytes_read=4220113 bytes_retransmit=9 bytes_invalid=0 send_seq=503450 receive_seq=503450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=1791 freq=400016132 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37282 bytes_read=116821 bytes_retransmit=0 bytes_invalid=0 send_seq=6185 receive_seq=6185 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997187 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=175868 bytes_read=5483036 bytes_retransmit=9 bytes_invalid=0 send_seq=24369 receive_seq=24369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997559 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115194 bytes_read=2915529 bytes_retransmit=9 bytes_invalid=0 send_seq=15796 receive_seq=15796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997435 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37549 bytes_read=1534555 bytes_retransmit=9 bytes_invalid=0 send_seq=6199 receive_seq=6199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997617 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38035 bytes_read=114532 bytes_retransmit=9 bytes_invalid=0 send_seq=6186 receive_seq=6186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92127 bytes_read=2366744 bytes_retransmit=0 bytes_invalid=0 send_seq=10745 receive_seq=10745 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998626 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=54.7 th1: temp=53.9 th2: temp=61.2 th3: temp=58.8 sysload=0.00 cputime=435.312 memavail=7395512 print_time=6036.773 buffer_time=2.175 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 53 Hz
Stats 6013.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26485742 bytes_read=4220933 bytes_retransmit=9 bytes_invalid=0 send_seq=503552 receive_seq=503552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=638 freq=400016148 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37288 bytes_read=116837 bytes_retransmit=0 bytes_invalid=0 send_seq=6186 receive_seq=6186 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997237 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=175944 bytes_read=5486109 bytes_retransmit=9 bytes_invalid=0 send_seq=24380 receive_seq=24380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997581 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115200 bytes_read=2915629 bytes_retransmit=9 bytes_invalid=0 send_seq=15797 receive_seq=15797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997487 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37555 bytes_read=1534789 bytes_retransmit=9 bytes_invalid=0 send_seq=6200 receive_seq=6200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38041 bytes_read=114548 bytes_retransmit=9 bytes_invalid=0 send_seq=6187 receive_seq=6187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92133 bytes_read=2367100 bytes_retransmit=0 bytes_invalid=0 send_seq=10746 receive_seq=10746 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998646 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=55.0 th1: temp=53.9 th2: temp=61.2 th3: temp=58.7 sysload=0.00 cputime=435.427 memavail=7395296 print_time=6037.667 buffer_time=2.069 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 54 Hz
Stats 6014.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26491223 bytes_read=4221797 bytes_retransmit=9 bytes_invalid=0 send_seq=503657 receive_seq=503657 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=1387 freq=400016162 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37294 bytes_read=116853 bytes_retransmit=0 bytes_invalid=0 send_seq=6187 receive_seq=6187 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997198 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=176020 bytes_read=5489179 bytes_retransmit=9 bytes_invalid=0 send_seq=24391 receive_seq=24391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997516 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115206 bytes_read=2915729 bytes_retransmit=9 bytes_invalid=0 send_seq=15798 receive_seq=15798 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997446 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37561 bytes_read=1535038 bytes_retransmit=9 bytes_invalid=0 send_seq=6201 receive_seq=6201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997606 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38047 bytes_read=114564 bytes_retransmit=9 bytes_invalid=0 send_seq=6188 receive_seq=6188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92139 bytes_read=2367456 bytes_retransmit=0 bytes_invalid=0 send_seq=10747 receive_seq=10747 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998631 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=55.0 th1: temp=54.0 th2: temp=61.3 th3: temp=58.8 sysload=0.00 cputime=435.541 memavail=7395404 print_time=6038.871 buffer_time=2.273 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 55 Hz
Stats 6015.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26495785 bytes_read=4222547 bytes_retransmit=9 bytes_invalid=0 send_seq=503745 receive_seq=503745 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=2141 freq=400016162 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37300 bytes_read=116869 bytes_retransmit=0 bytes_invalid=0 send_seq=6188 receive_seq=6188 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997174 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=176096 bytes_read=5492252 bytes_retransmit=9 bytes_invalid=0 send_seq=24402 receive_seq=24402 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997493 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115212 bytes_read=2915857 bytes_retransmit=9 bytes_invalid=0 send_seq=15799 receive_seq=15799 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997442 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37567 bytes_read=1535332 bytes_retransmit=9 bytes_invalid=0 send_seq=6202 receive_seq=6202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997582 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38053 bytes_read=114580 bytes_retransmit=9 bytes_invalid=0 send_seq=6189 receive_seq=6189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999425 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92145 bytes_read=2367812 bytes_retransmit=0 bytes_invalid=0 send_seq=10748 receive_seq=10748 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998622 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=54.8 th1: temp=53.9 th2: temp=61.3 th3: temp=58.9 sysload=0.00 cputime=435.642 memavail=7397328 print_time=6039.781 buffer_time=2.183 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 56 Hz
Stats 6016.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26501360 bytes_read=4223377 bytes_retransmit=9 bytes_invalid=0 send_seq=503849 receive_seq=503849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=943 freq=400016170 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37306 bytes_read=116885 bytes_retransmit=0 bytes_invalid=0 send_seq=6189 receive_seq=6189 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997179 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=176172 bytes_read=5495308 bytes_retransmit=9 bytes_invalid=0 send_seq=24413 receive_seq=24413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997499 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115218 bytes_read=2915969 bytes_retransmit=9 bytes_invalid=0 send_seq=15800 receive_seq=15800 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997444 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37573 bytes_read=1535566 bytes_retransmit=9 bytes_invalid=0 send_seq=6203 receive_seq=6203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38059 bytes_read=114596 bytes_retransmit=9 bytes_invalid=0 send_seq=6190 receive_seq=6190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999425 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92151 bytes_read=2368168 bytes_retransmit=0 bytes_invalid=0 send_seq=10749 receive_seq=10749 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998630 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=54.9 th1: temp=53.8 th2: temp=61.4 th3: temp=58.8 sysload=0.00 cputime=435.747 memavail=7397328 print_time=6040.696 buffer_time=2.096 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 57 Hz
Stats 6017.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26506960 bytes_read=4224257 bytes_retransmit=9 bytes_invalid=0 send_seq=503954 receive_seq=503954 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=1779 freq=400016152 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37312 bytes_read=116914 bytes_retransmit=0 bytes_invalid=0 send_seq=6190 receive_seq=6190 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997167 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=176248 bytes_read=5498373 bytes_retransmit=9 bytes_invalid=0 send_seq=24424 receive_seq=24424 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997466 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115224 bytes_read=2916075 bytes_retransmit=9 bytes_invalid=0 send_seq=15801 receive_seq=15801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997462 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37579 bytes_read=1535800 bytes_retransmit=9 bytes_invalid=0 send_seq=6204 receive_seq=6204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999568 adj=47997618 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38065 bytes_read=114623 bytes_retransmit=9 bytes_invalid=0 send_seq=6191 receive_seq=6191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999421 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92157 bytes_read=2368524 bytes_retransmit=0 bytes_invalid=0 send_seq=10750 receive_seq=10750 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998619 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=54.9 th1: temp=54.0 th2: temp=61.2 th3: temp=58.8 sysload=0.00 cputime=435.863 memavail=7397328 print_time=6041.903 buffer_time=2.300 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 58 Hz
Stats 6018.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26511656 bytes_read=4225012 bytes_retransmit=9 bytes_invalid=0 send_seq=504043 receive_seq=504043 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=2524 freq=400016126 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37318 bytes_read=116930 bytes_retransmit=0 bytes_invalid=0 send_seq=6191 receive_seq=6191 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997205 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=176324 bytes_read=5501486 bytes_retransmit=9 bytes_invalid=0 send_seq=24435 receive_seq=24435 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997523 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115230 bytes_read=2916181 bytes_retransmit=9 bytes_invalid=0 send_seq=15802 receive_seq=15802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37585 bytes_read=1536094 bytes_retransmit=9 bytes_invalid=0 send_seq=6205 receive_seq=6205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999567 adj=47997700 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38071 bytes_read=114639 bytes_retransmit=9 bytes_invalid=0 send_seq=6192 receive_seq=6192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92163 bytes_read=2368880 bytes_retransmit=0 bytes_invalid=0 send_seq=10751 receive_seq=10751 retransmit_seq=0 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998635 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=54.9 th1: temp=53.9 th2: temp=61.2 th3: temp=58.8 sysload=0.00 cputime=435.967 memavail=7395352 print_time=6042.793 buffer_time=2.188 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 59 Hz
Stats 6019.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26517479 bytes_read=4225862 bytes_retransmit=9 bytes_invalid=0 send_seq=504151 receive_seq=504151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=1339 freq=400016121 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37324 bytes_read=116946 bytes_retransmit=0 bytes_invalid=0 send_seq=6192 receive_seq=6192 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997270 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=176400 bytes_read=5504526 bytes_retransmit=9 bytes_invalid=0 send_seq=24446 receive_seq=24446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997570 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115236 bytes_read=2916274 bytes_retransmit=9 bytes_invalid=0 send_seq=15803 receive_seq=15803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997545 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37591 bytes_read=1536343 bytes_retransmit=9 bytes_invalid=0 send_seq=6206 receive_seq=6206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999566 adj=47997715 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38077 bytes_read=114655 bytes_retransmit=9 bytes_invalid=0 send_seq=6193 receive_seq=6193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92169 bytes_read=2369236 bytes_retransmit=0 bytes_invalid=0 send_seq=10752 receive_seq=10752 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998654 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=54.6 th1: temp=54.0 th2: temp=61.5 th3: temp=58.9 sysload=0.00 cputime=436.073 memavail=7395352 print_time=6043.719 buffer_time=2.111 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 60 Hz
Stats 6020.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26523310 bytes_read=4226751 bytes_retransmit=9 bytes_invalid=0 send_seq=504261 receive_seq=504261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=2060 freq=400016113 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37330 bytes_read=116962 bytes_retransmit=0 bytes_invalid=0 send_seq=6193 receive_seq=6193 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997274 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=176476 bytes_read=5507652 bytes_retransmit=9 bytes_invalid=0 send_seq=24457 receive_seq=24457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997559 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115242 bytes_read=2916395 bytes_retransmit=9 bytes_invalid=0 send_seq=15804 receive_seq=15804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997540 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37597 bytes_read=1536577 bytes_retransmit=9 bytes_invalid=0 send_seq=6207 receive_seq=6207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997697 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38083 bytes_read=114671 bytes_retransmit=9 bytes_invalid=0 send_seq=6194 receive_seq=6194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92175 bytes_read=2369592 bytes_retransmit=0 bytes_invalid=0 send_seq=10753 receive_seq=10753 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998651 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=54.8 th1: temp=53.9 th2: temp=61.3 th3: temp=58.9 sysload=0.00 cputime=436.187 memavail=7395352 print_time=6044.923 buffer_time=2.303 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 61 Hz
Stats 6021.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26528138 bytes_read=4227516 bytes_retransmit=9 bytes_invalid=0 send_seq=504353 receive_seq=504352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=2689 freq=400016089 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37336 bytes_read=116978 bytes_retransmit=0 bytes_invalid=0 send_seq=6194 receive_seq=6194 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997258 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=176552 bytes_read=5510709 bytes_retransmit=9 bytes_invalid=0 send_seq=24468 receive_seq=24468 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997571 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115248 bytes_read=2916509 bytes_retransmit=9 bytes_invalid=0 send_seq=15805 receive_seq=15805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37603 bytes_read=1536871 bytes_retransmit=9 bytes_invalid=0 send_seq=6208 receive_seq=6208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999566 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38089 bytes_read=114687 bytes_retransmit=9 bytes_invalid=0 send_seq=6195 receive_seq=6195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92181 bytes_read=2369948 bytes_retransmit=0 bytes_invalid=0 send_seq=10754 receive_seq=10754 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998651 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=54.8 th1: temp=54.0 th2: temp=61.3 th3: temp=58.9 sysload=0.00 cputime=436.289 memavail=7395352 print_time=6045.804 buffer_time=2.184 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 62 Hz
Stats 6022.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26533968 bytes_read=4228387 bytes_retransmit=9 bytes_invalid=0 send_seq=504461 receive_seq=504461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=1534 freq=400016154 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37342 bytes_read=117006 bytes_retransmit=0 bytes_invalid=0 send_seq=6195 receive_seq=6195 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997279 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=176628 bytes_read=5513767 bytes_retransmit=9 bytes_invalid=0 send_seq=24479 receive_seq=24479 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997599 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115254 bytes_read=2916609 bytes_retransmit=9 bytes_invalid=0 send_seq=15806 receive_seq=15806 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997567 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37609 bytes_read=1537105 bytes_retransmit=9 bytes_invalid=0 send_seq=6209 receive_seq=6209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999572 adj=47997727 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38095 bytes_read=114714 bytes_retransmit=9 bytes_invalid=0 send_seq=6196 receive_seq=6196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92187 bytes_read=2370304 bytes_retransmit=0 bytes_invalid=0 send_seq=10755 receive_seq=10755 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998735 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=54.9 th1: temp=54.0 th2: temp=61.4 th3: temp=59.1 sysload=0.00 cputime=436.395 memavail=7395352 print_time=6046.721 buffer_time=2.101 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 63 Hz
Stats 6023.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26539850 bytes_read=4229252 bytes_retransmit=9 bytes_invalid=0 send_seq=504567 receive_seq=504567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=2481 freq=400016142 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37348 bytes_read=117021 bytes_retransmit=0 bytes_invalid=0 send_seq=6196 receive_seq=6196 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997177 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=176704 bytes_read=5516870 bytes_retransmit=9 bytes_invalid=0 send_seq=24490 receive_seq=24490 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997461 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115260 bytes_read=2916737 bytes_retransmit=9 bytes_invalid=0 send_seq=15807 receive_seq=15807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997414 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37615 bytes_read=1537339 bytes_retransmit=9 bytes_invalid=0 send_seq=6210 receive_seq=6210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999571 adj=47997695 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38101 bytes_read=114730 bytes_retransmit=9 bytes_invalid=0 send_seq=6197 receive_seq=6197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92193 bytes_read=2370660 bytes_retransmit=0 bytes_invalid=0 send_seq=10756 receive_seq=10756 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998652 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=54.9 th1: temp=54.3 th2: temp=61.3 th3: temp=58.9 sysload=0.00 cputime=436.510 memavail=7395352 print_time=6047.935 buffer_time=2.314 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 64 Hz
Stats 6024.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26544824 bytes_read=4230027 bytes_retransmit=9 bytes_invalid=0 send_seq=504660 receive_seq=504660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=3058 freq=400016152 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37354 bytes_read=117036 bytes_retransmit=0 bytes_invalid=0 send_seq=6197 receive_seq=6197 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997195 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=176780 bytes_read=5519928 bytes_retransmit=9 bytes_invalid=0 send_seq=24501 receive_seq=24501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997525 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115266 bytes_read=2916837 bytes_retransmit=9 bytes_invalid=0 send_seq=15808 receive_seq=15808 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997442 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37621 bytes_read=1537648 bytes_retransmit=9 bytes_invalid=0 send_seq=6211 receive_seq=6211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999569 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38107 bytes_read=114746 bytes_retransmit=9 bytes_invalid=0 send_seq=6198 receive_seq=6198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92199 bytes_read=2371016 bytes_retransmit=0 bytes_invalid=0 send_seq=10757 receive_seq=10757 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998668 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=54.9 th1: temp=54.2 th2: temp=61.4 th3: temp=58.9 sysload=0.00 cputime=436.614 memavail=7395352 print_time=6048.820 buffer_time=2.198 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 65 Hz
Stats 6025.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26550885 bytes_read=4230897 bytes_retransmit=9 bytes_invalid=0 send_seq=504772 receive_seq=504772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=2014 freq=400016140 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37360 bytes_read=117051 bytes_retransmit=0 bytes_invalid=0 send_seq=6198 receive_seq=6198 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997179 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=176856 bytes_read=5522989 bytes_retransmit=9 bytes_invalid=0 send_seq=24512 receive_seq=24512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997498 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115272 bytes_read=2916937 bytes_retransmit=9 bytes_invalid=0 send_seq=15809 receive_seq=15809 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997429 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37627 bytes_read=1537882 bytes_retransmit=9 bytes_invalid=0 send_seq=6212 receive_seq=6212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999572 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38113 bytes_read=114762 bytes_retransmit=9 bytes_invalid=0 send_seq=6199 receive_seq=6199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92205 bytes_read=2371372 bytes_retransmit=0 bytes_invalid=0 send_seq=10758 receive_seq=10758 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998644 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=54.8 th1: temp=54.0 th2: temp=61.4 th3: temp=59.0 sysload=0.00 cputime=436.723 memavail=7395352 print_time=6049.744 buffer_time=2.120 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 66 Hz
Stats 6026.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26557019 bytes_read=4231801 bytes_retransmit=9 bytes_invalid=0 send_seq=504885 receive_seq=504885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=2879 freq=400016139 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37366 bytes_read=117066 bytes_retransmit=0 bytes_invalid=0 send_seq=6199 receive_seq=6199 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997197 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=176932 bytes_read=5526134 bytes_retransmit=9 bytes_invalid=0 send_seq=24523 receive_seq=24523 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997608 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115278 bytes_read=2917079 bytes_retransmit=9 bytes_invalid=0 send_seq=15810 receive_seq=15810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997453 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37633 bytes_read=1538131 bytes_retransmit=9 bytes_invalid=0 send_seq=6213 receive_seq=6213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999570 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38119 bytes_read=114778 bytes_retransmit=9 bytes_invalid=0 send_seq=6200 receive_seq=6200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92211 bytes_read=2371728 bytes_retransmit=0 bytes_invalid=0 send_seq=10759 receive_seq=10759 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998710 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=55.0 th1: temp=54.0 th2: temp=61.0 th3: temp=59.0 sysload=0.00 cputime=436.837 memavail=7395352 print_time=6050.951 buffer_time=2.320 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 67 Hz
Stats 6027.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26562138 bytes_read=4232617 bytes_retransmit=9 bytes_invalid=0 send_seq=504983 receive_seq=504983 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=3401 freq=400016118 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37372 bytes_read=117095 bytes_retransmit=0 bytes_invalid=0 send_seq=6200 receive_seq=6200 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997213 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=177008 bytes_read=5529191 bytes_retransmit=9 bytes_invalid=0 send_seq=24534 receive_seq=24534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997697 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115284 bytes_read=2917179 bytes_retransmit=9 bytes_invalid=0 send_seq=15811 receive_seq=15811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997453 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37639 bytes_read=1538410 bytes_retransmit=9 bytes_invalid=0 send_seq=6214 receive_seq=6214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999570 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38125 bytes_read=114805 bytes_retransmit=9 bytes_invalid=0 send_seq=6201 receive_seq=6201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92217 bytes_read=2372084 bytes_retransmit=0 bytes_invalid=0 send_seq=10760 receive_seq=10760 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998698 coil_temp=16.9 refs=0 mcu_temp=20.18 supply_voltage=3.012 th0: temp=54.8 th1: temp=53.8 th2: temp=61.4 th3: temp=59.1 sysload=0.00 cputime=436.943 memavail=7395352 print_time=6051.827 buffer_time=2.195 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 68 Hz
Stats 6028.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26568391 bytes_read=4233507 bytes_retransmit=9 bytes_invalid=0 send_seq=505099 receive_seq=505099 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=2257 freq=400016133 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37378 bytes_read=117111 bytes_retransmit=0 bytes_invalid=0 send_seq=6201 receive_seq=6201 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997231 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=177084 bytes_read=5532268 bytes_retransmit=9 bytes_invalid=0 send_seq=24545 receive_seq=24545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000247 adj=63997778 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115290 bytes_read=2917279 bytes_retransmit=9 bytes_invalid=0 send_seq=15812 receive_seq=15812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997545 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37645 bytes_read=1538644 bytes_retransmit=9 bytes_invalid=0 send_seq=6215 receive_seq=6215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999575 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38131 bytes_read=114821 bytes_retransmit=9 bytes_invalid=0 send_seq=6202 receive_seq=6202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92223 bytes_read=2372440 bytes_retransmit=0 bytes_invalid=0 send_seq=10761 receive_seq=10761 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998705 coil_temp=16.9 refs=0 mcu_temp=20.18 supply_voltage=3.012 th0: temp=54.9 th1: temp=54.0 th2: temp=61.3 th3: temp=58.8 sysload=0.00 cputime=437.058 memavail=7394424 print_time=6052.747 buffer_time=2.115 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 69 Hz
Stats 6029.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26574600 bytes_read=4234406 bytes_retransmit=9 bytes_invalid=0 send_seq=505211 receive_seq=505211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=1911 freq=400016110 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37384 bytes_read=117127 bytes_retransmit=0 bytes_invalid=0 send_seq=6202 receive_seq=6202 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997205 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=177160 bytes_read=5535354 bytes_retransmit=9 bytes_invalid=0 send_seq=24556 receive_seq=24556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000264 adj=63997954 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115296 bytes_read=2917407 bytes_retransmit=9 bytes_invalid=0 send_seq=15813 receive_seq=15813 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997502 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37651 bytes_read=1538908 bytes_retransmit=9 bytes_invalid=0 send_seq=6216 receive_seq=6216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999573 adj=47997717 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38137 bytes_read=114837 bytes_retransmit=9 bytes_invalid=0 send_seq=6203 receive_seq=6203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92229 bytes_read=2372796 bytes_retransmit=0 bytes_invalid=0 send_seq=10762 receive_seq=10762 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998672 coil_temp=16.9 refs=0 mcu_temp=20.17 supply_voltage=3.012 th0: temp=55.0 th1: temp=54.0 th2: temp=61.4 th3: temp=58.8 sysload=0.00 cputime=437.165 memavail=7394424 print_time=6053.634 buffer_time=2.001 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 70 Hz
Stats 6030.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26579836 bytes_read=4235216 bytes_retransmit=9 bytes_invalid=0 send_seq=505311 receive_seq=505311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=3763 freq=400016130 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37390 bytes_read=117143 bytes_retransmit=0 bytes_invalid=0 send_seq=6203 receive_seq=6203 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997263 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=177236 bytes_read=5538411 bytes_retransmit=9 bytes_invalid=0 send_seq=24567 receive_seq=24567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000260 adj=63998187 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115302 bytes_read=2917507 bytes_retransmit=9 bytes_invalid=0 send_seq=15814 receive_seq=15814 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997542 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37657 bytes_read=1539187 bytes_retransmit=9 bytes_invalid=0 send_seq=6217 receive_seq=6217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999572 adj=47997719 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38143 bytes_read=114853 bytes_retransmit=9 bytes_invalid=0 send_seq=6204 receive_seq=6204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92235 bytes_read=2373152 bytes_retransmit=0 bytes_invalid=0 send_seq=10763 receive_seq=10763 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998718 coil_temp=16.9 refs=0 mcu_temp=20.17 supply_voltage=3.012 th0: temp=54.9 th1: temp=54.2 th2: temp=61.4 th3: temp=59.0 sysload=0.08 cputime=437.290 memavail=7389172 print_time=6054.842 buffer_time=2.209 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 71 Hz
Stats 6031.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26586217 bytes_read=4236116 bytes_retransmit=9 bytes_invalid=0 send_seq=505429 receive_seq=505429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=2826 freq=400016145 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37396 bytes_read=117159 bytes_retransmit=0 bytes_invalid=0 send_seq=6204 receive_seq=6204 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997225 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=177312 bytes_read=5541470 bytes_retransmit=9 bytes_invalid=0 send_seq=24578 receive_seq=24578 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000255 adj=63997947 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115308 bytes_read=2917621 bytes_retransmit=9 bytes_invalid=0 send_seq=15815 receive_seq=15815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997478 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37663 bytes_read=1539421 bytes_retransmit=9 bytes_invalid=0 send_seq=6218 receive_seq=6218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999571 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38149 bytes_read=114869 bytes_retransmit=9 bytes_invalid=0 send_seq=6205 receive_seq=6205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92241 bytes_read=2373508 bytes_retransmit=0 bytes_invalid=0 send_seq=10764 receive_seq=10764 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998668 coil_temp=16.9 refs=0 mcu_temp=20.17 supply_voltage=3.012 th0: temp=55.0 th1: temp=54.0 th2: temp=61.2 th3: temp=59.1 sysload=0.08 cputime=437.403 memavail=7395024 print_time=6055.765 buffer_time=2.131 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 72 Hz
Stats 6032.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26592675 bytes_read=4237071 bytes_retransmit=9 bytes_invalid=0 send_seq=505549 receive_seq=505549 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=2245 freq=400016131 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=37402 bytes_read=117188 bytes_retransmit=0 bytes_invalid=0 send_seq=6205 receive_seq=6205 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997222 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=177388 bytes_read=5544612 bytes_retransmit=9 bytes_invalid=0 send_seq=24589 receive_seq=24589 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000250 adj=63997819 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115314 bytes_read=2917749 bytes_retransmit=9 bytes_invalid=0 send_seq=15816 receive_seq=15816 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997474 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37669 bytes_read=1539670 bytes_retransmit=9 bytes_invalid=0 send_seq=6219 receive_seq=6219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999569 adj=47997606 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38155 bytes_read=114896 bytes_retransmit=9 bytes_invalid=0 send_seq=6206 receive_seq=6206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92247 bytes_read=2373864 bytes_retransmit=0 bytes_invalid=0 send_seq=10765 receive_seq=10765 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998638 coil_temp=16.9 refs=0 mcu_temp=20.17 supply_voltage=3.012 th0: temp=55.0 th1: temp=54.1 th2: temp=61.6 th3: temp=59.0 sysload=0.08 cputime=437.511 memavail=7395024 print_time=6056.649 buffer_time=2.015 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 73 Hz
Stats 6033.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26598149 bytes_read=4237905 bytes_retransmit=9 bytes_invalid=0 send_seq=505652 receive_seq=505652 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=4085 freq=400016093 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=37414 bytes_read=117220 bytes_retransmit=0 bytes_invalid=0 send_seq=6207 receive_seq=6207 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997248 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=177463 bytes_read=5547679 bytes_retransmit=9 bytes_invalid=0 send_seq=24600 receive_seq=24600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000242 adj=63997771 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115326 bytes_read=2917865 bytes_retransmit=9 bytes_invalid=0 send_seq=15818 receive_seq=15818 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37681 bytes_read=1539965 bytes_retransmit=9 bytes_invalid=0 send_seq=6221 receive_seq=6221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999567 adj=47997613 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38167 bytes_read=114928 bytes_retransmit=9 bytes_invalid=0 send_seq=6208 receive_seq=6208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92259 bytes_read=2374236 bytes_retransmit=0 bytes_invalid=0 send_seq=10767 receive_seq=10767 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998651 coil_temp=16.9 refs=0 mcu_temp=20.18 supply_voltage=3.012 th0: temp=55.1 th1: temp=54.2 th2: temp=61.5 th3: temp=59.0 sysload=0.08 cputime=437.627 memavail=7395024 print_time=6057.852 buffer_time=2.217 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 74 Hz
Stats 6034.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26604640 bytes_read=4238806 bytes_retransmit=9 bytes_invalid=0 send_seq=505771 receive_seq=505771 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=3377 freq=400016100 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=37420 bytes_read=117236 bytes_retransmit=0 bytes_invalid=0 send_seq=6208 receive_seq=6208 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997294 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=177539 bytes_read=5550736 bytes_retransmit=9 bytes_invalid=0 send_seq=24611 receive_seq=24611 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997710 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115332 bytes_read=2917965 bytes_retransmit=9 bytes_invalid=0 send_seq=15819 receive_seq=15819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997581 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37687 bytes_read=1540214 bytes_retransmit=9 bytes_invalid=0 send_seq=6222 receive_seq=6222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999565 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38173 bytes_read=114944 bytes_retransmit=9 bytes_invalid=0 send_seq=6209 receive_seq=6209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92265 bytes_read=2374592 bytes_retransmit=0 bytes_invalid=0 send_seq=10768 receive_seq=10768 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998681 coil_temp=16.9 refs=0 mcu_temp=20.18 supply_voltage=3.012 th0: temp=55.1 th1: temp=54.1 th2: temp=61.5 th3: temp=59.2 sysload=0.08 cputime=437.738 memavail=7394772 print_time=6058.785 buffer_time=2.150 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 75 Hz
Stats 6035.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26611257 bytes_read=4239750 bytes_retransmit=9 bytes_invalid=0 send_seq=505892 receive_seq=505892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=2509 freq=400016086 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=37426 bytes_read=117252 bytes_retransmit=0 bytes_invalid=0 send_seq=6209 receive_seq=6209 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997271 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=177615 bytes_read=5553820 bytes_retransmit=9 bytes_invalid=0 send_seq=24622 receive_seq=24622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997640 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115338 bytes_read=2918093 bytes_retransmit=9 bytes_invalid=0 send_seq=15820 receive_seq=15820 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997543 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37693 bytes_read=1540463 bytes_retransmit=9 bytes_invalid=0 send_seq=6223 receive_seq=6223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997616 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38179 bytes_read=114960 bytes_retransmit=9 bytes_invalid=0 send_seq=6210 receive_seq=6210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92271 bytes_read=2374948 bytes_retransmit=0 bytes_invalid=0 send_seq=10769 receive_seq=10769 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998657 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=55.0 th1: temp=54.2 th2: temp=61.4 th3: temp=59.0 sysload=0.08 cputime=437.852 memavail=7394776 print_time=6059.657 buffer_time=2.020 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 76 Hz
Stats 6036.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26616801 bytes_read=4240575 bytes_retransmit=9 bytes_invalid=0 send_seq=505995 receive_seq=505995 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=4428 freq=400016088 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=37432 bytes_read=117268 bytes_retransmit=0 bytes_invalid=0 send_seq=6210 receive_seq=6210 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997286 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=177691 bytes_read=5556877 bytes_retransmit=9 bytes_invalid=0 send_seq=24633 receive_seq=24633 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997640 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115344 bytes_read=2918207 bytes_retransmit=9 bytes_invalid=0 send_seq=15821 receive_seq=15821 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37699 bytes_read=1540742 bytes_retransmit=9 bytes_invalid=0 send_seq=6224 receive_seq=6224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997621 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38185 bytes_read=114976 bytes_retransmit=9 bytes_invalid=0 send_seq=6211 receive_seq=6211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92277 bytes_read=2375304 bytes_retransmit=0 bytes_invalid=0 send_seq=10770 receive_seq=10770 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998664 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=54.8 th1: temp=54.1 th2: temp=61.5 th3: temp=59.0 sysload=0.08 cputime=437.980 memavail=7392872 print_time=6060.859 buffer_time=2.221 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 77 Hz
Stats 6037.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26623473 bytes_read=4241521 bytes_retransmit=9 bytes_invalid=0 send_seq=506119 receive_seq=506119 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=3822 freq=400016062 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37438 bytes_read=117297 bytes_retransmit=0 bytes_invalid=0 send_seq=6211 receive_seq=6211 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997281 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=177767 bytes_read=5559934 bytes_retransmit=9 bytes_invalid=0 send_seq=24644 receive_seq=24644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997608 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115350 bytes_read=2918307 bytes_retransmit=9 bytes_invalid=0 send_seq=15822 receive_seq=15822 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997535 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37705 bytes_read=1540976 bytes_retransmit=9 bytes_invalid=0 send_seq=6225 receive_seq=6225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997610 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38191 bytes_read=115003 bytes_retransmit=9 bytes_invalid=0 send_seq=6212 receive_seq=6212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92283 bytes_read=2375660 bytes_retransmit=0 bytes_invalid=0 send_seq=10771 receive_seq=10771 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998657 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.2 th1: temp=54.2 th2: temp=61.5 th3: temp=59.0 sysload=0.08 cputime=438.095 memavail=7398316 print_time=6061.798 buffer_time=2.160 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 78 Hz
Stats 6038.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26630321 bytes_read=4242475 bytes_retransmit=9 bytes_invalid=0 send_seq=506242 receive_seq=506242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=2827 freq=400016048 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37444 bytes_read=117313 bytes_retransmit=0 bytes_invalid=0 send_seq=6212 receive_seq=6212 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997309 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=177843 bytes_read=5563035 bytes_retransmit=9 bytes_invalid=0 send_seq=24655 receive_seq=24655 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997637 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115356 bytes_read=2918435 bytes_retransmit=9 bytes_invalid=0 send_seq=15823 receive_seq=15823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997581 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37711 bytes_read=1541225 bytes_retransmit=9 bytes_invalid=0 send_seq=6226 receive_seq=6226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38197 bytes_read=115019 bytes_retransmit=9 bytes_invalid=0 send_seq=6213 receive_seq=6213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92289 bytes_read=2376016 bytes_retransmit=0 bytes_invalid=0 send_seq=10772 receive_seq=10772 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998670 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=55.2 th1: temp=54.1 th2: temp=61.6 th3: temp=59.0 sysload=0.08 cputime=438.210 memavail=7396816 print_time=6062.668 buffer_time=2.030 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 79 Hz
Stats 6039.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26635996 bytes_read=4243320 bytes_retransmit=9 bytes_invalid=0 send_seq=506349 receive_seq=506349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=4637 freq=400016056 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37450 bytes_read=117329 bytes_retransmit=0 bytes_invalid=0 send_seq=6213 receive_seq=6213 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997321 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=177919 bytes_read=5566091 bytes_retransmit=9 bytes_invalid=0 send_seq=24666 receive_seq=24666 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997624 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115362 bytes_read=2918535 bytes_retransmit=9 bytes_invalid=0 send_seq=15824 receive_seq=15824 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997589 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37717 bytes_read=1541519 bytes_retransmit=9 bytes_invalid=0 send_seq=6227 receive_seq=6227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38203 bytes_read=115035 bytes_retransmit=9 bytes_invalid=0 send_seq=6214 receive_seq=6214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92295 bytes_read=2376372 bytes_retransmit=0 bytes_invalid=0 send_seq=10773 receive_seq=10773 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998672 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=55.0 th1: temp=54.2 th2: temp=61.7 th3: temp=59.0 sysload=0.08 cputime=438.331 memavail=7396820 print_time=6063.874 buffer_time=2.235 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 80 Hz
Stats 6040.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26642820 bytes_read=4244255 bytes_retransmit=9 bytes_invalid=0 send_seq=506474 receive_seq=506474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=4121 freq=400016038 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37456 bytes_read=117345 bytes_retransmit=0 bytes_invalid=0 send_seq=6214 receive_seq=6214 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997279 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=177995 bytes_read=5569206 bytes_retransmit=9 bytes_invalid=0 send_seq=24677 receive_seq=24677 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997682 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115368 bytes_read=2918635 bytes_retransmit=9 bytes_invalid=0 send_seq=15825 receive_seq=15825 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37723 bytes_read=1541753 bytes_retransmit=9 bytes_invalid=0 send_seq=6228 receive_seq=6228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38209 bytes_read=115051 bytes_retransmit=9 bytes_invalid=0 send_seq=6215 receive_seq=6215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92301 bytes_read=2376728 bytes_retransmit=0 bytes_invalid=0 send_seq=10774 receive_seq=10774 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998722 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=55.1 th1: temp=54.1 th2: temp=61.4 th3: temp=59.0 sysload=0.07 cputime=438.449 memavail=7396568 print_time=6064.806 buffer_time=2.167 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 81 Hz
Stats 6041.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26649649 bytes_read=4245214 bytes_retransmit=9 bytes_invalid=0 send_seq=506598 receive_seq=506598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=3110 freq=400016046 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37462 bytes_read=117361 bytes_retransmit=0 bytes_invalid=0 send_seq=6215 receive_seq=6215 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997297 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=178071 bytes_read=5572290 bytes_retransmit=9 bytes_invalid=0 send_seq=24688 receive_seq=24688 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997670 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115374 bytes_read=2918777 bytes_retransmit=9 bytes_invalid=0 send_seq=15826 receive_seq=15826 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997599 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37729 bytes_read=1542002 bytes_retransmit=9 bytes_invalid=0 send_seq=6229 receive_seq=6229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38215 bytes_read=115067 bytes_retransmit=9 bytes_invalid=0 send_seq=6216 receive_seq=6216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92307 bytes_read=2377084 bytes_retransmit=0 bytes_invalid=0 send_seq=10775 receive_seq=10775 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998729 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=55.0 th1: temp=53.9 th2: temp=61.5 th3: temp=59.1 sysload=0.07 cputime=438.565 memavail=7396568 print_time=6065.678 buffer_time=2.038 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 82 Hz
Stats 6042.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26655517 bytes_read=4246085 bytes_retransmit=9 bytes_invalid=0 send_seq=506707 receive_seq=506707 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=4997 freq=400016038 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37468 bytes_read=117390 bytes_retransmit=0 bytes_invalid=0 send_seq=6216 receive_seq=6216 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997279 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=178147 bytes_read=5575347 bytes_retransmit=9 bytes_invalid=0 send_seq=24699 receive_seq=24699 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997619 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115380 bytes_read=2918877 bytes_retransmit=9 bytes_invalid=0 send_seq=15827 receive_seq=15827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997566 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37735 bytes_read=1542281 bytes_retransmit=9 bytes_invalid=0 send_seq=6230 receive_seq=6230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38221 bytes_read=115094 bytes_retransmit=9 bytes_invalid=0 send_seq=6217 receive_seq=6217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92313 bytes_read=2377440 bytes_retransmit=0 bytes_invalid=0 send_seq=10776 receive_seq=10776 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998707 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=55.2 th1: temp=54.1 th2: temp=61.4 th3: temp=59.1 sysload=0.07 cputime=438.691 memavail=7396568 print_time=6066.882 buffer_time=2.242 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 83 Hz
Stats 6043.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26662515 bytes_read=4247030 bytes_retransmit=9 bytes_invalid=0 send_seq=506834 receive_seq=506834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=4401 freq=400016016 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37474 bytes_read=117406 bytes_retransmit=0 bytes_invalid=0 send_seq=6217 receive_seq=6217 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997274 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=178223 bytes_read=5578421 bytes_retransmit=9 bytes_invalid=0 send_seq=24710 receive_seq=24710 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997610 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115386 bytes_read=2918977 bytes_retransmit=9 bytes_invalid=0 send_seq=15828 receive_seq=15828 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997545 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37741 bytes_read=1542515 bytes_retransmit=9 bytes_invalid=0 send_seq=6231 receive_seq=6231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38227 bytes_read=115110 bytes_retransmit=9 bytes_invalid=0 send_seq=6218 receive_seq=6218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92319 bytes_read=2377796 bytes_retransmit=0 bytes_invalid=0 send_seq=10777 receive_seq=10777 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998691 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=55.0 th1: temp=54.1 th2: temp=61.5 th3: temp=58.9 sysload=0.07 cputime=438.807 memavail=7396344 print_time=6067.819 buffer_time=2.178 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 84 Hz
Stats 6044.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26669461 bytes_read=4247980 bytes_retransmit=9 bytes_invalid=0 send_seq=506957 receive_seq=506957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=3196 freq=400016016 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37480 bytes_read=117422 bytes_retransmit=0 bytes_invalid=0 send_seq=6218 receive_seq=6218 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997299 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=178299 bytes_read=5581507 bytes_retransmit=9 bytes_invalid=0 send_seq=24721 receive_seq=24721 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997634 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115392 bytes_read=2919105 bytes_retransmit=9 bytes_invalid=0 send_seq=15829 receive_seq=15829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997586 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37747 bytes_read=1542794 bytes_retransmit=9 bytes_invalid=0 send_seq=6232 receive_seq=6232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38233 bytes_read=115126 bytes_retransmit=9 bytes_invalid=0 send_seq=6219 receive_seq=6219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92325 bytes_read=2378152 bytes_retransmit=0 bytes_invalid=0 send_seq=10778 receive_seq=10778 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998699 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=54.9 th1: temp=54.3 th2: temp=61.4 th3: temp=59.0 sysload=0.07 cputime=438.939 memavail=7396112 print_time=6068.690 buffer_time=2.049 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 85 Hz
Stats 6045.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26675334 bytes_read=4248834 bytes_retransmit=9 bytes_invalid=0 send_seq=507066 receive_seq=507066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=5236 freq=400016008 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37486 bytes_read=117438 bytes_retransmit=0 bytes_invalid=0 send_seq=6219 receive_seq=6219 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997295 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=178375 bytes_read=5584563 bytes_retransmit=9 bytes_invalid=0 send_seq=24732 receive_seq=24732 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997725 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115398 bytes_read=2919205 bytes_retransmit=9 bytes_invalid=0 send_seq=15830 receive_seq=15830 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997564 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37753 bytes_read=1543058 bytes_retransmit=9 bytes_invalid=0 send_seq=6233 receive_seq=6233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38239 bytes_read=115142 bytes_retransmit=9 bytes_invalid=0 send_seq=6220 receive_seq=6220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92331 bytes_read=2378508 bytes_retransmit=0 bytes_invalid=0 send_seq=10779 receive_seq=10779 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998689 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=55.1 th1: temp=54.1 th2: temp=61.5 th3: temp=59.0 sysload=0.06 cputime=439.063 memavail=7396112 print_time=6069.881 buffer_time=2.239 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 86 Hz
Stats 6046.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26682337 bytes_read=4249764 bytes_retransmit=9 bytes_invalid=0 send_seq=507190 receive_seq=507190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=4845 freq=400016017 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37492 bytes_read=117454 bytes_retransmit=0 bytes_invalid=0 send_seq=6220 receive_seq=6220 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997285 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=178444 bytes_read=5587599 bytes_retransmit=9 bytes_invalid=0 send_seq=24742 receive_seq=24742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997694 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115404 bytes_read=2919319 bytes_retransmit=9 bytes_invalid=0 send_seq=15831 receive_seq=15831 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997622 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37759 bytes_read=1543292 bytes_retransmit=9 bytes_invalid=0 send_seq=6234 receive_seq=6234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38245 bytes_read=115158 bytes_retransmit=9 bytes_invalid=0 send_seq=6221 receive_seq=6221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92337 bytes_read=2378864 bytes_retransmit=0 bytes_invalid=0 send_seq=10780 receive_seq=10780 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998684 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=55.0 th1: temp=54.1 th2: temp=61.5 th3: temp=59.0 sysload=0.06 cputime=439.175 memavail=7396132 print_time=6070.820 buffer_time=2.178 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 87 Hz
Stats 6047.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26689582 bytes_read=4250779 bytes_retransmit=9 bytes_invalid=0 send_seq=507322 receive_seq=507322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=3463 freq=400016040 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=37498 bytes_read=117483 bytes_retransmit=0 bytes_invalid=0 send_seq=6221 receive_seq=6221 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997263 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=178520 bytes_read=5590743 bytes_retransmit=9 bytes_invalid=0 send_seq=24753 receive_seq=24753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997638 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115410 bytes_read=2919447 bytes_retransmit=9 bytes_invalid=0 send_seq=15832 receive_seq=15832 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997579 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37765 bytes_read=1543556 bytes_retransmit=9 bytes_invalid=0 send_seq=6235 receive_seq=6235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38251 bytes_read=115185 bytes_retransmit=9 bytes_invalid=0 send_seq=6222 receive_seq=6222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92343 bytes_read=2379220 bytes_retransmit=0 bytes_invalid=0 send_seq=10781 receive_seq=10781 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998699 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.2 th1: temp=54.2 th2: temp=61.5 th3: temp=59.1 sysload=0.06 cputime=439.298 memavail=7390592 print_time=6071.695 buffer_time=2.052 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 88 Hz
Stats 6048.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26695546 bytes_read=4251629 bytes_retransmit=9 bytes_invalid=0 send_seq=507430 receive_seq=507430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=5410 freq=400016032 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=37504 bytes_read=117499 bytes_retransmit=0 bytes_invalid=0 send_seq=6222 receive_seq=6222 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997221 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=178596 bytes_read=5593818 bytes_retransmit=9 bytes_invalid=0 send_seq=24764 receive_seq=24764 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997560 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115416 bytes_read=2919547 bytes_retransmit=9 bytes_invalid=0 send_seq=15833 receive_seq=15833 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997574 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37771 bytes_read=1543820 bytes_retransmit=9 bytes_invalid=0 send_seq=6236 receive_seq=6236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997600 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38257 bytes_read=115201 bytes_retransmit=9 bytes_invalid=0 send_seq=6223 receive_seq=6223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92349 bytes_read=2379576 bytes_retransmit=0 bytes_invalid=0 send_seq=10782 receive_seq=10782 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998664 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=55.2 th1: temp=54.2 th2: temp=61.5 th3: temp=58.9 sysload=0.06 cputime=439.431 memavail=7395504 print_time=6072.894 buffer_time=2.251 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 89 Hz
Stats 6049.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26702744 bytes_read=4252574 bytes_retransmit=9 bytes_invalid=0 send_seq=507557 receive_seq=507557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=5045 freq=400016030 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=37510 bytes_read=117515 bytes_retransmit=0 bytes_invalid=0 send_seq=6223 receive_seq=6223 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997234 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=178672 bytes_read=5596875 bytes_retransmit=9 bytes_invalid=0 send_seq=24775 receive_seq=24775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997571 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115422 bytes_read=2919647 bytes_retransmit=9 bytes_invalid=0 send_seq=15834 receive_seq=15834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997552 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37777 bytes_read=1544069 bytes_retransmit=9 bytes_invalid=0 send_seq=6237 receive_seq=6237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38263 bytes_read=115217 bytes_retransmit=9 bytes_invalid=0 send_seq=6224 receive_seq=6224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92355 bytes_read=2379932 bytes_retransmit=0 bytes_invalid=0 send_seq=10783 receive_seq=10783 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998667 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=55.0 th1: temp=54.1 th2: temp=61.5 th3: temp=59.2 sysload=0.06 cputime=439.547 memavail=7395504 print_time=6073.832 buffer_time=2.188 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 90 Hz
Stats 6050.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26709968 bytes_read=4253573 bytes_retransmit=9 bytes_invalid=0 send_seq=507689 receive_seq=507689 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=3647 freq=400016018 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=37516 bytes_read=117531 bytes_retransmit=0 bytes_invalid=0 send_seq=6224 receive_seq=6224 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997253 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=178748 bytes_read=5599960 bytes_retransmit=9 bytes_invalid=0 send_seq=24786 receive_seq=24786 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997649 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115428 bytes_read=2919775 bytes_retransmit=9 bytes_invalid=0 send_seq=15835 receive_seq=15835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997533 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37783 bytes_read=1544333 bytes_retransmit=9 bytes_invalid=0 send_seq=6238 receive_seq=6238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997616 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38269 bytes_read=115233 bytes_retransmit=9 bytes_invalid=0 send_seq=6225 receive_seq=6225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92361 bytes_read=2380288 bytes_retransmit=0 bytes_invalid=0 send_seq=10784 receive_seq=10784 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998661 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=55.1 th1: temp=54.5 th2: temp=61.5 th3: temp=59.1 sysload=0.06 cputime=439.666 memavail=7395504 print_time=6074.703 buffer_time=2.058 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 91 Hz
Stats 6051.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26716112 bytes_read=4254448 bytes_retransmit=9 bytes_invalid=0 send_seq=507802 receive_seq=507802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=5613 freq=400016057 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=37522 bytes_read=117547 bytes_retransmit=0 bytes_invalid=0 send_seq=6225 receive_seq=6225 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997265 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=178824 bytes_read=5603018 bytes_retransmit=9 bytes_invalid=0 send_seq=24797 receive_seq=24797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997640 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115434 bytes_read=2919889 bytes_retransmit=9 bytes_invalid=0 send_seq=15836 receive_seq=15836 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997543 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37789 bytes_read=1544597 bytes_retransmit=9 bytes_invalid=0 send_seq=6239 receive_seq=6239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38275 bytes_read=115249 bytes_retransmit=9 bytes_invalid=0 send_seq=6226 receive_seq=6226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92367 bytes_read=2380644 bytes_retransmit=0 bytes_invalid=0 send_seq=10785 receive_seq=10785 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998659 coil_temp=16.8 refs=0 mcu_temp=20.18 supply_voltage=3.012 th0: temp=55.2 th1: temp=54.3 th2: temp=61.5 th3: temp=59.0 sysload=0.06 cputime=439.792 memavail=7395504 print_time=6075.901 buffer_time=2.255 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 92 Hz
Stats 6052.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26723303 bytes_read=4255419 bytes_retransmit=9 bytes_invalid=0 send_seq=507931 receive_seq=507931 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=5394 freq=400016069 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37528 bytes_read=117576 bytes_retransmit=0 bytes_invalid=0 send_seq=6226 receive_seq=6226 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997186 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=178900 bytes_read=5606075 bytes_retransmit=9 bytes_invalid=0 send_seq=24808 receive_seq=24808 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997537 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115440 bytes_read=2919989 bytes_retransmit=9 bytes_invalid=0 send_seq=15837 receive_seq=15837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997441 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37795 bytes_read=1544831 bytes_retransmit=9 bytes_invalid=0 send_seq=6240 receive_seq=6240 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997571 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38281 bytes_read=115276 bytes_retransmit=9 bytes_invalid=0 send_seq=6227 receive_seq=6227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92373 bytes_read=2381000 bytes_retransmit=0 bytes_invalid=0 send_seq=10786 receive_seq=10786 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998658 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.012 th0: temp=55.2 th1: temp=54.2 th2: temp=61.5 th3: temp=58.9 sysload=0.06 cputime=439.908 memavail=7395504 print_time=6076.844 buffer_time=2.197 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 93 Hz
Stats 6053.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26730760 bytes_read=4256433 bytes_retransmit=9 bytes_invalid=0 send_seq=508066 receive_seq=508066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=3783 freq=400016049 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37534 bytes_read=117592 bytes_retransmit=0 bytes_invalid=0 send_seq=6227 receive_seq=6227 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997171 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=178976 bytes_read=5609178 bytes_retransmit=9 bytes_invalid=0 send_seq=24819 receive_seq=24819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997503 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115446 bytes_read=2920117 bytes_retransmit=9 bytes_invalid=0 send_seq=15838 receive_seq=15838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997441 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37801 bytes_read=1545095 bytes_retransmit=9 bytes_invalid=0 send_seq=6241 receive_seq=6241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997552 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38287 bytes_read=115292 bytes_retransmit=9 bytes_invalid=0 send_seq=6228 receive_seq=6228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92379 bytes_read=2381356 bytes_retransmit=0 bytes_invalid=0 send_seq=10787 receive_seq=10787 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998640 coil_temp=16.8 refs=0 mcu_temp=20.18 supply_voltage=3.012 th0: temp=55.0 th1: temp=54.1 th2: temp=61.6 th3: temp=59.0 sysload=0.06 cputime=440.026 memavail=7395504 print_time=6077.710 buffer_time=2.064 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 94 Hz
Stats 6054.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26736942 bytes_read=4257313 bytes_retransmit=9 bytes_invalid=0 send_seq=508180 receive_seq=508180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=6018 freq=400016038 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37540 bytes_read=117608 bytes_retransmit=0 bytes_invalid=0 send_seq=6228 receive_seq=6228 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997211 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=179052 bytes_read=5612292 bytes_retransmit=9 bytes_invalid=0 send_seq=24830 receive_seq=24830 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997544 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115452 bytes_read=2920217 bytes_retransmit=9 bytes_invalid=0 send_seq=15839 receive_seq=15839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997472 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37807 bytes_read=1545374 bytes_retransmit=9 bytes_invalid=0 send_seq=6242 receive_seq=6242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997584 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38293 bytes_read=115308 bytes_retransmit=9 bytes_invalid=0 send_seq=6229 receive_seq=6229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92385 bytes_read=2381712 bytes_retransmit=0 bytes_invalid=0 send_seq=10788 receive_seq=10788 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998652 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=55.2 th1: temp=54.0 th2: temp=61.5 th3: temp=59.1 sysload=0.06 cputime=440.153 memavail=7395504 print_time=6078.918 buffer_time=2.261 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 95 Hz
Stats 6055.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26744257 bytes_read=4258277 bytes_retransmit=9 bytes_invalid=0 send_seq=508309 receive_seq=508309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=5786 freq=400016022 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37546 bytes_read=117624 bytes_retransmit=0 bytes_invalid=0 send_seq=6229 receive_seq=6229 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997236 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=179128 bytes_read=5615349 bytes_retransmit=9 bytes_invalid=0 send_seq=24841 receive_seq=24841 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997587 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115458 bytes_read=2920317 bytes_retransmit=9 bytes_invalid=0 send_seq=15840 receive_seq=15840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997489 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37813 bytes_read=1545608 bytes_retransmit=9 bytes_invalid=0 send_seq=6243 receive_seq=6243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997611 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38299 bytes_read=115324 bytes_retransmit=9 bytes_invalid=0 send_seq=6230 receive_seq=6230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92391 bytes_read=2382068 bytes_retransmit=0 bytes_invalid=0 send_seq=10789 receive_seq=10789 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998679 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.012 th0: temp=55.2 th1: temp=54.1 th2: temp=61.6 th3: temp=59.1 sysload=0.05 cputime=440.270 memavail=7395504 print_time=6079.846 buffer_time=2.189 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 96 Hz
Stats 6056.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26751928 bytes_read=4259292 bytes_retransmit=9 bytes_invalid=0 send_seq=508447 receive_seq=508447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=4075 freq=400016014 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37552 bytes_read=117640 bytes_retransmit=0 bytes_invalid=0 send_seq=6230 receive_seq=6230 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997258 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=179204 bytes_read=5618433 bytes_retransmit=9 bytes_invalid=0 send_seq=24852 receive_seq=24852 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997603 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115464 bytes_read=2920459 bytes_retransmit=9 bytes_invalid=0 send_seq=15841 receive_seq=15841 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37819 bytes_read=1545887 bytes_retransmit=9 bytes_invalid=0 send_seq=6244 receive_seq=6244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997630 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38305 bytes_read=115340 bytes_retransmit=9 bytes_invalid=0 send_seq=6231 receive_seq=6231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92397 bytes_read=2382424 bytes_retransmit=0 bytes_invalid=0 send_seq=10790 receive_seq=10790 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998705 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.012 th0: temp=55.3 th1: temp=54.1 th2: temp=61.6 th3: temp=59.0 sysload=0.05 cputime=440.389 memavail=7395504 print_time=6080.722 buffer_time=2.065 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 97 Hz
Stats 6057.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26758305 bytes_read=4260213 bytes_retransmit=9 bytes_invalid=0 send_seq=508566 receive_seq=508566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=35 upcoming_bytes=6118 freq=400016018 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37558 bytes_read=117669 bytes_retransmit=0 bytes_invalid=0 send_seq=6231 receive_seq=6231 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997264 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=179280 bytes_read=5621490 bytes_retransmit=9 bytes_invalid=0 send_seq=24863 receive_seq=24863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997793 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115470 bytes_read=2920559 bytes_retransmit=9 bytes_invalid=0 send_seq=15842 receive_seq=15842 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37825 bytes_read=1546136 bytes_retransmit=9 bytes_invalid=0 send_seq=6245 receive_seq=6245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38311 bytes_read=115367 bytes_retransmit=9 bytes_invalid=0 send_seq=6232 receive_seq=6232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999454 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92403 bytes_read=2382780 bytes_retransmit=0 bytes_invalid=0 send_seq=10791 receive_seq=10791 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998695 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.012 th0: temp=55.1 th1: temp=54.1 th2: temp=61.6 th3: temp=59.0 sysload=0.05 cputime=440.517 memavail=7395504 print_time=6081.921 buffer_time=2.262 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 98 Hz
Stats 6058.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26765809 bytes_read=4261232 bytes_retransmit=9 bytes_invalid=0 send_seq=508702 receive_seq=508702 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=5889 freq=400016068 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37564 bytes_read=117685 bytes_retransmit=0 bytes_invalid=0 send_seq=6232 receive_seq=6232 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997249 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=179356 bytes_read=5624622 bytes_retransmit=9 bytes_invalid=0 send_seq=24874 receive_seq=24874 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997811 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115476 bytes_read=2920659 bytes_retransmit=9 bytes_invalid=0 send_seq=15843 receive_seq=15843 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37831 bytes_read=1546370 bytes_retransmit=9 bytes_invalid=0 send_seq=6246 receive_seq=6246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38317 bytes_read=115383 bytes_retransmit=9 bytes_invalid=0 send_seq=6233 receive_seq=6233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92409 bytes_read=2383136 bytes_retransmit=0 bytes_invalid=0 send_seq=10792 receive_seq=10792 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998686 coil_temp=16.8 refs=0 mcu_temp=20.18 supply_voltage=3.012 th0: temp=55.3 th1: temp=54.2 th2: temp=61.6 th3: temp=59.1 sysload=0.05 cputime=440.638 memavail=7394604 print_time=6082.849 buffer_time=2.190 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 99 Hz
Stats 6059.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26773517 bytes_read=4262237 bytes_retransmit=9 bytes_invalid=0 send_seq=508841 receive_seq=508841 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=4215 freq=400016048 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37570 bytes_read=117701 bytes_retransmit=0 bytes_invalid=0 send_seq=6233 receive_seq=6233 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997158 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=179432 bytes_read=5627707 bytes_retransmit=9 bytes_invalid=0 send_seq=24885 receive_seq=24885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997657 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115482 bytes_read=2920787 bytes_retransmit=9 bytes_invalid=0 send_seq=15844 receive_seq=15844 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997396 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37837 bytes_read=1546664 bytes_retransmit=9 bytes_invalid=0 send_seq=6247 receive_seq=6247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997574 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38323 bytes_read=115399 bytes_retransmit=9 bytes_invalid=0 send_seq=6234 receive_seq=6234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92415 bytes_read=2383492 bytes_retransmit=0 bytes_invalid=0 send_seq=10793 receive_seq=10793 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998627 coil_temp=16.8 refs=0 mcu_temp=20.18 supply_voltage=3.011 th0: temp=55.3 th1: temp=53.9 th2: temp=61.6 th3: temp=59.1 sysload=0.05 cputime=440.758 memavail=7394604 print_time=6083.716 buffer_time=2.057 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 100 Hz
Stats 6060.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26779858 bytes_read=4263122 bytes_retransmit=9 bytes_invalid=0 send_seq=508956 receive_seq=508956 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=6373 freq=400016040 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37576 bytes_read=117717 bytes_retransmit=0 bytes_invalid=0 send_seq=6234 receive_seq=6234 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997200 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=179508 bytes_read=5630764 bytes_retransmit=9 bytes_invalid=0 send_seq=24896 receive_seq=24896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997657 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115488 bytes_read=2920887 bytes_retransmit=9 bytes_invalid=0 send_seq=15845 receive_seq=15845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997435 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37843 bytes_read=1546913 bytes_retransmit=9 bytes_invalid=0 send_seq=6248 receive_seq=6248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997609 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38329 bytes_read=115415 bytes_retransmit=9 bytes_invalid=0 send_seq=6235 receive_seq=6235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92421 bytes_read=2383848 bytes_retransmit=0 bytes_invalid=0 send_seq=10794 receive_seq=10794 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998642 coil_temp=16.8 refs=0 mcu_temp=20.18 supply_voltage=3.011 th0: temp=55.1 th1: temp=54.4 th2: temp=61.3 th3: temp=59.0 sysload=0.05 cputime=440.888 memavail=7394604 print_time=6084.923 buffer_time=2.264 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 101 Hz
Stats 6061.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26787455 bytes_read=4264131 bytes_retransmit=9 bytes_invalid=0 send_seq=509090 receive_seq=509090 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=46 upcoming_bytes=6303 freq=400016056 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37582 bytes_read=117733 bytes_retransmit=0 bytes_invalid=0 send_seq=6235 receive_seq=6235 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997221 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=179584 bytes_read=5633822 bytes_retransmit=9 bytes_invalid=0 send_seq=24907 receive_seq=24907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997636 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115494 bytes_read=2921001 bytes_retransmit=9 bytes_invalid=0 send_seq=15846 receive_seq=15846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997455 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37849 bytes_read=1547131 bytes_retransmit=9 bytes_invalid=0 send_seq=6249 receive_seq=6249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997617 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38335 bytes_read=115431 bytes_retransmit=9 bytes_invalid=0 send_seq=6236 receive_seq=6236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92427 bytes_read=2384204 bytes_retransmit=0 bytes_invalid=0 send_seq=10795 receive_seq=10795 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998651 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.3 th2: temp=61.7 th3: temp=59.1 sysload=0.05 cputime=441.008 memavail=7394612 print_time=6085.859 buffer_time=2.198 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 102 Hz
Stats 6062.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26795275 bytes_read=4265147 bytes_retransmit=9 bytes_invalid=0 send_seq=509228 receive_seq=509228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=4515 freq=400016029 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37588 bytes_read=117762 bytes_retransmit=0 bytes_invalid=0 send_seq=6236 receive_seq=6236 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997199 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=179660 bytes_read=5636906 bytes_retransmit=9 bytes_invalid=0 send_seq=24918 receive_seq=24918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997577 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115500 bytes_read=2921129 bytes_retransmit=9 bytes_invalid=0 send_seq=15847 receive_seq=15847 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997418 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37855 bytes_read=1547405 bytes_retransmit=9 bytes_invalid=0 send_seq=6250 receive_seq=6250 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997607 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38341 bytes_read=115458 bytes_retransmit=9 bytes_invalid=0 send_seq=6237 receive_seq=6237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92433 bytes_read=2384560 bytes_retransmit=0 bytes_invalid=0 send_seq=10796 receive_seq=10796 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999948 adj=31998689 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=55.2 th1: temp=54.2 th2: temp=61.6 th3: temp=59.1 sysload=0.05 cputime=441.130 memavail=7394620 print_time=6086.727 buffer_time=2.065 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 103 Hz
Stats 6063.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26801926 bytes_read=4266072 bytes_retransmit=9 bytes_invalid=0 send_seq=509351 receive_seq=509351 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=5423 freq=400016016 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37594 bytes_read=117778 bytes_retransmit=0 bytes_invalid=0 send_seq=6237 receive_seq=6237 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997244 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=179729 bytes_read=5639960 bytes_retransmit=9 bytes_invalid=0 send_seq=24928 receive_seq=24928 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997609 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115506 bytes_read=2921229 bytes_retransmit=9 bytes_invalid=0 send_seq=15848 receive_seq=15848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997482 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37861 bytes_read=1547623 bytes_retransmit=9 bytes_invalid=0 send_seq=6251 receive_seq=6251 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38347 bytes_read=115474 bytes_retransmit=9 bytes_invalid=0 send_seq=6238 receive_seq=6238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92439 bytes_read=2384916 bytes_retransmit=0 bytes_invalid=0 send_seq=10797 receive_seq=10797 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998738 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.0 th2: temp=61.3 th3: temp=59.1 sysload=0.05 cputime=441.249 memavail=7394620 print_time=6087.663 buffer_time=2.001 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 104 Hz
Stats 6064.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26809577 bytes_read=4267096 bytes_retransmit=9 bytes_invalid=0 send_seq=509488 receive_seq=509488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=6621 freq=400015994 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37600 bytes_read=117794 bytes_retransmit=0 bytes_invalid=0 send_seq=6238 receive_seq=6238 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997256 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=179805 bytes_read=5643017 bytes_retransmit=9 bytes_invalid=0 send_seq=24939 receive_seq=24939 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997633 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115512 bytes_read=2921329 bytes_retransmit=9 bytes_invalid=0 send_seq=15849 receive_seq=15849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997501 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37867 bytes_read=1547856 bytes_retransmit=9 bytes_invalid=0 send_seq=6252 receive_seq=6252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38353 bytes_read=115490 bytes_retransmit=9 bytes_invalid=0 send_seq=6239 receive_seq=6239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92445 bytes_read=2385272 bytes_retransmit=0 bytes_invalid=0 send_seq=10798 receive_seq=10798 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998722 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.2 th2: temp=61.7 th3: temp=59.0 sysload=0.05 cputime=441.383 memavail=7394620 print_time=6088.866 buffer_time=2.203 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 105 Hz
Stats 6065.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26817635 bytes_read=4268141 bytes_retransmit=9 bytes_invalid=0 send_seq=509635 receive_seq=509635 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=4797 freq=400016004 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37606 bytes_read=117810 bytes_retransmit=0 bytes_invalid=0 send_seq=6239 receive_seq=6239 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997271 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=179881 bytes_read=5646101 bytes_retransmit=9 bytes_invalid=0 send_seq=24950 receive_seq=24950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997655 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115518 bytes_read=2921457 bytes_retransmit=9 bytes_invalid=0 send_seq=15850 receive_seq=15850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997540 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37873 bytes_read=1548130 bytes_retransmit=9 bytes_invalid=0 send_seq=6253 receive_seq=6253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38359 bytes_read=115506 bytes_retransmit=9 bytes_invalid=0 send_seq=6240 receive_seq=6240 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92451 bytes_read=2385628 bytes_retransmit=0 bytes_invalid=0 send_seq=10799 receive_seq=10799 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998714 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.3 th2: temp=61.6 th3: temp=59.2 sysload=0.20 cputime=441.517 memavail=7394996 print_time=6089.735 buffer_time=2.072 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 106 Hz
Stats 6066.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=26824237 bytes_read=4269051 bytes_retransmit=9 bytes_invalid=0 send_seq=509756 receive_seq=509756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=5764 freq=400016005 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37612 bytes_read=117826 bytes_retransmit=0 bytes_invalid=0 send_seq=6240 receive_seq=6240 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997257 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=179957 bytes_read=5649218 bytes_retransmit=9 bytes_invalid=0 send_seq=24961 receive_seq=24961 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997614 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115524 bytes_read=2921571 bytes_retransmit=9 bytes_invalid=0 send_seq=15851 receive_seq=15851 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37879 bytes_read=1548352 bytes_retransmit=9 bytes_invalid=0 send_seq=6254 receive_seq=6254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38365 bytes_read=115522 bytes_retransmit=9 bytes_invalid=0 send_seq=6241 receive_seq=6241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92457 bytes_read=2385968 bytes_retransmit=0 bytes_invalid=0 send_seq=10800 receive_seq=10800 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998682 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.2 th1: temp=54.3 th2: temp=61.6 th3: temp=59.1 sysload=0.20 cputime=441.638 memavail=7394996 print_time=6090.668 buffer_time=2.005 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 107 Hz
Stats 6067.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26832217 bytes_read=4270121 bytes_retransmit=9 bytes_invalid=0 send_seq=509899 receive_seq=509899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=6891 freq=400015989 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37618 bytes_read=117842 bytes_retransmit=0 bytes_invalid=0 send_seq=6241 receive_seq=6241 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997251 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=180033 bytes_read=5652274 bytes_retransmit=9 bytes_invalid=0 send_seq=24972 receive_seq=24972 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997592 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115530 bytes_read=2921671 bytes_retransmit=9 bytes_invalid=0 send_seq=15852 receive_seq=15852 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37885 bytes_read=1548586 bytes_retransmit=9 bytes_invalid=0 send_seq=6255 receive_seq=6255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38371 bytes_read=115549 bytes_retransmit=9 bytes_invalid=0 send_seq=6242 receive_seq=6242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92463 bytes_read=2386324 bytes_retransmit=0 bytes_invalid=0 send_seq=10801 receive_seq=10801 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998669 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.3 th2: temp=61.5 th3: temp=59.1 sysload=0.20 cputime=441.773 memavail=7394996 print_time=6091.872 buffer_time=2.208 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 108 Hz
Stats 6068.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26840291 bytes_read=4271146 bytes_retransmit=9 bytes_invalid=0 send_seq=510042 receive_seq=510042 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=4967 freq=400015974 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37624 bytes_read=117871 bytes_retransmit=0 bytes_invalid=0 send_seq=6242 receive_seq=6242 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997270 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000120 mcu_task_stddev=0.000069 bytes_write=180109 bytes_read=5655377 bytes_retransmit=9 bytes_invalid=0 send_seq=24983 receive_seq=24983 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997615 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115536 bytes_read=2921799 bytes_retransmit=9 bytes_invalid=0 send_seq=15853 receive_seq=15853 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997558 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=37891 bytes_read=1548880 bytes_retransmit=9 bytes_invalid=0 send_seq=6256 receive_seq=6256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38377 bytes_read=115565 bytes_retransmit=9 bytes_invalid=0 send_seq=6243 receive_seq=6243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92469 bytes_read=2386680 bytes_retransmit=0 bytes_invalid=0 send_seq=10802 receive_seq=10802 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998677 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.3 th2: temp=61.5 th3: temp=59.1 sysload=0.20 cputime=441.899 memavail=7396312 print_time=6092.743 buffer_time=2.079 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 109 Hz
Stats 6069.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26847055 bytes_read=4272076 bytes_retransmit=9 bytes_invalid=0 send_seq=510166 receive_seq=510166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=5985 freq=400015969 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37630 bytes_read=117887 bytes_retransmit=0 bytes_invalid=0 send_seq=6243 receive_seq=6243 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997311 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000120 mcu_task_stddev=0.000069 bytes_write=180185 bytes_read=5658434 bytes_retransmit=9 bytes_invalid=0 send_seq=24994 receive_seq=24994 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997644 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115542 bytes_read=2921899 bytes_retransmit=9 bytes_invalid=0 send_seq=15854 receive_seq=15854 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997573 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37897 bytes_read=1549129 bytes_retransmit=9 bytes_invalid=0 send_seq=6257 receive_seq=6257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38383 bytes_read=115581 bytes_retransmit=9 bytes_invalid=0 send_seq=6244 receive_seq=6244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999462 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92475 bytes_read=2387036 bytes_retransmit=0 bytes_invalid=0 send_seq=10803 receive_seq=10803 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998719 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.1 th2: temp=61.5 th3: temp=59.0 sysload=0.20 cputime=442.019 memavail=7396176 print_time=6093.671 buffer_time=2.007 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 110 Hz
Stats 6070.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26855081 bytes_read=4273140 bytes_retransmit=9 bytes_invalid=0 send_seq=510311 receive_seq=510311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=7218 freq=400015956 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37636 bytes_read=117903 bytes_retransmit=0 bytes_invalid=0 send_seq=6244 receive_seq=6244 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997298 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000120 mcu_task_stddev=0.000069 bytes_write=180261 bytes_read=5661491 bytes_retransmit=9 bytes_invalid=0 send_seq=25005 receive_seq=25005 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997676 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115548 bytes_read=2921999 bytes_retransmit=9 bytes_invalid=0 send_seq=15855 receive_seq=15855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997579 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37903 bytes_read=1549363 bytes_retransmit=9 bytes_invalid=0 send_seq=6258 receive_seq=6258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997698 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38389 bytes_read=115597 bytes_retransmit=9 bytes_invalid=0 send_seq=6245 receive_seq=6245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999459 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92481 bytes_read=2387392 bytes_retransmit=0 bytes_invalid=0 send_seq=10804 receive_seq=10804 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999947 adj=31998703 coil_temp=16.8 refs=0 mcu_temp=20.18 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.2 th2: temp=61.5 th3: temp=59.1 sysload=0.19 cputime=442.159 memavail=7395924 print_time=6094.876 buffer_time=2.211 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 111 Hz
Stats 6071.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26863361 bytes_read=4274190 bytes_retransmit=9 bytes_invalid=0 send_seq=510460 receive_seq=510459 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=5205 freq=400015944 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37642 bytes_read=117919 bytes_retransmit=0 bytes_invalid=0 send_seq=6245 receive_seq=6245 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997296 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000120 mcu_task_stddev=0.000069 bytes_write=180337 bytes_read=5664576 bytes_retransmit=9 bytes_invalid=0 send_seq=25016 receive_seq=25016 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997692 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115554 bytes_read=2922141 bytes_retransmit=9 bytes_invalid=0 send_seq=15856 receive_seq=15856 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997568 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37909 bytes_read=1549657 bytes_retransmit=9 bytes_invalid=0 send_seq=6259 receive_seq=6259 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38395 bytes_read=115613 bytes_retransmit=9 bytes_invalid=0 send_seq=6246 receive_seq=6246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92487 bytes_read=2387748 bytes_retransmit=0 bytes_invalid=0 send_seq=10805 receive_seq=10805 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998733 coil_temp=16.8 refs=0 mcu_temp=20.18 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.1 th2: temp=61.4 th3: temp=59.0 sysload=0.19 cputime=442.289 memavail=7395924 print_time=6095.739 buffer_time=2.074 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 112 Hz
Stats 6072.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26870295 bytes_read=4275156 bytes_retransmit=9 bytes_invalid=0 send_seq=510587 receive_seq=510587 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=6088 freq=400015925 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37648 bytes_read=117935 bytes_retransmit=0 bytes_invalid=0 send_seq=6246 receive_seq=6246 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997297 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000120 mcu_task_stddev=0.000069 bytes_write=180413 bytes_read=5667632 bytes_retransmit=9 bytes_invalid=0 send_seq=25027 receive_seq=25027 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997697 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115560 bytes_read=2922241 bytes_retransmit=9 bytes_invalid=0 send_seq=15857 receive_seq=15857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997609 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37915 bytes_read=1549891 bytes_retransmit=9 bytes_invalid=0 send_seq=6260 receive_seq=6260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997705 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38401 bytes_read=115640 bytes_retransmit=9 bytes_invalid=0 send_seq=6247 receive_seq=6247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92493 bytes_read=2388104 bytes_retransmit=0 bytes_invalid=0 send_seq=10806 receive_seq=10806 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998724 coil_temp=16.8 refs=0 mcu_temp=20.18 supply_voltage=3.011 th0: temp=55.2 th1: temp=54.2 th2: temp=61.6 th3: temp=59.1 sysload=0.19 cputime=442.416 memavail=7395924 print_time=6096.674 buffer_time=2.009 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 113 Hz
Stats 6073.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26878377 bytes_read=4276225 bytes_retransmit=9 bytes_invalid=0 send_seq=510733 receive_seq=510733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=7307 freq=400015905 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37654 bytes_read=117964 bytes_retransmit=0 bytes_invalid=0 send_seq=6247 receive_seq=6247 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997318 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=180489 bytes_read=5670707 bytes_retransmit=9 bytes_invalid=0 send_seq=25038 receive_seq=25038 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997832 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115566 bytes_read=2922341 bytes_retransmit=9 bytes_invalid=0 send_seq=15858 receive_seq=15858 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997623 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37921 bytes_read=1550125 bytes_retransmit=9 bytes_invalid=0 send_seq=6261 receive_seq=6261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997717 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38407 bytes_read=115656 bytes_retransmit=9 bytes_invalid=0 send_seq=6248 receive_seq=6248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92499 bytes_read=2388460 bytes_retransmit=0 bytes_invalid=0 send_seq=10807 receive_seq=10807 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998723 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.4 th2: temp=61.6 th3: temp=59.1 sysload=0.19 cputime=442.558 memavail=7395924 print_time=6097.882 buffer_time=2.217 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 114 Hz
Stats 6074.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26886758 bytes_read=4277285 bytes_retransmit=9 bytes_invalid=0 send_seq=510883 receive_seq=510883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=5353 freq=400015917 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37660 bytes_read=117980 bytes_retransmit=0 bytes_invalid=0 send_seq=6248 receive_seq=6248 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997327 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=180565 bytes_read=5673851 bytes_retransmit=9 bytes_invalid=0 send_seq=25049 receive_seq=25049 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997793 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115572 bytes_read=2922469 bytes_retransmit=9 bytes_invalid=0 send_seq=15859 receive_seq=15859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997617 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37927 bytes_read=1550434 bytes_retransmit=9 bytes_invalid=0 send_seq=6262 receive_seq=6262 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997716 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38413 bytes_read=115672 bytes_retransmit=9 bytes_invalid=0 send_seq=6249 receive_seq=6249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92505 bytes_read=2388816 bytes_retransmit=0 bytes_invalid=0 send_seq=10808 receive_seq=10808 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998709 coil_temp=16.8 refs=0 mcu_temp=20.18 supply_voltage=3.011 th0: temp=55.2 th1: temp=53.9 th2: temp=61.6 th3: temp=58.9 sysload=0.19 cputime=442.690 memavail=7395924 print_time=6098.755 buffer_time=2.089 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 115 Hz
Stats 6075.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26893643 bytes_read=4278225 bytes_retransmit=9 bytes_invalid=0 send_seq=511009 receive_seq=511009 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=6409 freq=400015909 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37666 bytes_read=117996 bytes_retransmit=0 bytes_invalid=0 send_seq=6249 receive_seq=6249 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997303 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=180641 bytes_read=5676907 bytes_retransmit=9 bytes_invalid=0 send_seq=25060 receive_seq=25060 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997742 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115578 bytes_read=2922569 bytes_retransmit=9 bytes_invalid=0 send_seq=15860 receive_seq=15860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997573 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37933 bytes_read=1550668 bytes_retransmit=9 bytes_invalid=0 send_seq=6263 receive_seq=6263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38419 bytes_read=115688 bytes_retransmit=9 bytes_invalid=0 send_seq=6250 receive_seq=6250 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92511 bytes_read=2389172 bytes_retransmit=0 bytes_invalid=0 send_seq=10809 receive_seq=10809 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998679 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=55.1 th1: temp=54.4 th2: temp=61.6 th3: temp=59.1 sysload=0.17 cputime=442.818 memavail=7395924 print_time=6099.678 buffer_time=2.012 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 116 Hz
Stats 6076.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26901884 bytes_read=4279292 bytes_retransmit=9 bytes_invalid=0 send_seq=511155 receive_seq=511155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=23 upcoming_bytes=7698 freq=400015939 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37672 bytes_read=118012 bytes_retransmit=0 bytes_invalid=0 send_seq=6250 receive_seq=6250 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997309 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=180710 bytes_read=5679943 bytes_retransmit=9 bytes_invalid=0 send_seq=25070 receive_seq=25070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997719 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115584 bytes_read=2922683 bytes_retransmit=9 bytes_invalid=0 send_seq=15861 receive_seq=15861 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997618 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37939 bytes_read=1550902 bytes_retransmit=9 bytes_invalid=0 send_seq=6264 receive_seq=6264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997694 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38425 bytes_read=115704 bytes_retransmit=9 bytes_invalid=0 send_seq=6251 receive_seq=6251 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92517 bytes_read=2389528 bytes_retransmit=0 bytes_invalid=0 send_seq=10810 receive_seq=10810 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998671 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.5 th2: temp=61.5 th3: temp=59.1 sysload=0.17 cputime=442.961 memavail=7395924 print_time=6100.887 buffer_time=2.220 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 117 Hz
Stats 6077.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26910367 bytes_read=4280370 bytes_retransmit=9 bytes_invalid=0 send_seq=511306 receive_seq=511306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=5500 freq=400015955 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37678 bytes_read=118028 bytes_retransmit=0 bytes_invalid=0 send_seq=6251 receive_seq=6251 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999233 adj=49997247 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=180786 bytes_read=5683028 bytes_retransmit=9 bytes_invalid=0 send_seq=25081 receive_seq=25081 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997624 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115590 bytes_read=2922811 bytes_retransmit=9 bytes_invalid=0 send_seq=15862 receive_seq=15862 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37945 bytes_read=1551196 bytes_retransmit=9 bytes_invalid=0 send_seq=6265 receive_seq=6265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38431 bytes_read=115731 bytes_retransmit=9 bytes_invalid=0 send_seq=6252 receive_seq=6252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92523 bytes_read=2389884 bytes_retransmit=0 bytes_invalid=0 send_seq=10811 receive_seq=10811 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998651 coil_temp=16.8 refs=0 mcu_temp=20.18 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.3 th2: temp=61.6 th3: temp=59.0 sysload=0.17 cputime=443.094 memavail=7395940 print_time=6101.755 buffer_time=2.088 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 118 Hz
Stats 6078.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26917429 bytes_read=4281325 bytes_retransmit=9 bytes_invalid=0 send_seq=511435 receive_seq=511435 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=6534 freq=400015942 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37684 bytes_read=118057 bytes_retransmit=0 bytes_invalid=0 send_seq=6252 receive_seq=6252 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997208 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=180862 bytes_read=5686101 bytes_retransmit=9 bytes_invalid=0 send_seq=25092 receive_seq=25092 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997588 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115596 bytes_read=2922911 bytes_retransmit=9 bytes_invalid=0 send_seq=15863 receive_seq=15863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997479 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37951 bytes_read=1551430 bytes_retransmit=9 bytes_invalid=0 send_seq=6266 receive_seq=6266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997621 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38437 bytes_read=115747 bytes_retransmit=9 bytes_invalid=0 send_seq=6253 receive_seq=6253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92529 bytes_read=2390240 bytes_retransmit=0 bytes_invalid=0 send_seq=10812 receive_seq=10812 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998633 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=55.2 th1: temp=54.3 th2: temp=61.5 th3: temp=59.1 sysload=0.17 cputime=443.223 memavail=7395940 print_time=6102.684 buffer_time=2.016 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 119 Hz
Stats 6079.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26925620 bytes_read=4282394 bytes_retransmit=9 bytes_invalid=0 send_seq=511581 receive_seq=511581 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=52 upcoming_bytes=7718 freq=400015931 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37690 bytes_read=118073 bytes_retransmit=0 bytes_invalid=0 send_seq=6253 receive_seq=6253 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999233 adj=49997236 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=180938 bytes_read=5689158 bytes_retransmit=9 bytes_invalid=0 send_seq=25103 receive_seq=25103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997620 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115602 bytes_read=2923011 bytes_retransmit=9 bytes_invalid=0 send_seq=15864 receive_seq=15864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997507 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37957 bytes_read=1551679 bytes_retransmit=9 bytes_invalid=0 send_seq=6267 receive_seq=6267 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38443 bytes_read=115763 bytes_retransmit=9 bytes_invalid=0 send_seq=6254 receive_seq=6254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92535 bytes_read=2390596 bytes_retransmit=0 bytes_invalid=0 send_seq=10813 receive_seq=10813 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998640 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.012 th0: temp=55.3 th1: temp=54.5 th2: temp=61.6 th3: temp=59.1 sysload=0.17 cputime=443.364 memavail=7395940 print_time=6103.884 buffer_time=2.215 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 120 Hz
Stats 6080.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26934284 bytes_read=4283479 bytes_retransmit=9 bytes_invalid=0 send_seq=511736 receive_seq=511736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=5536 freq=400015938 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37696 bytes_read=118089 bytes_retransmit=0 bytes_invalid=0 send_seq=6254 receive_seq=6254 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997254 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=181014 bytes_read=5692242 bytes_retransmit=9 bytes_invalid=0 send_seq=25114 receive_seq=25114 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997634 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115608 bytes_read=2923139 bytes_retransmit=9 bytes_invalid=0 send_seq=15865 receive_seq=15865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997517 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37963 bytes_read=1551973 bytes_retransmit=9 bytes_invalid=0 send_seq=6268 receive_seq=6268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38449 bytes_read=115779 bytes_retransmit=9 bytes_invalid=0 send_seq=6255 receive_seq=6255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92541 bytes_read=2390952 bytes_retransmit=0 bytes_invalid=0 send_seq=10814 receive_seq=10814 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998645 coil_temp=16.8 refs=0 mcu_temp=20.18 supply_voltage=3.011 th0: temp=55.2 th1: temp=54.3 th2: temp=61.6 th3: temp=59.1 sysload=0.16 cputime=443.495 memavail=7395976 print_time=6104.762 buffer_time=2.092 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 121 Hz
Stats 6081.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26941317 bytes_read=4284429 bytes_retransmit=9 bytes_invalid=0 send_seq=511864 receive_seq=511864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=6740 freq=400015926 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37702 bytes_read=118105 bytes_retransmit=0 bytes_invalid=0 send_seq=6255 receive_seq=6255 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997252 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=181090 bytes_read=5695357 bytes_retransmit=9 bytes_invalid=0 send_seq=25125 receive_seq=25125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997607 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115614 bytes_read=2923239 bytes_retransmit=9 bytes_invalid=0 send_seq=15866 receive_seq=15866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997493 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37969 bytes_read=1552207 bytes_retransmit=9 bytes_invalid=0 send_seq=6269 receive_seq=6269 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38455 bytes_read=115795 bytes_retransmit=9 bytes_invalid=0 send_seq=6256 receive_seq=6256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92547 bytes_read=2391308 bytes_retransmit=0 bytes_invalid=0 send_seq=10815 receive_seq=10815 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998626 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.4 th2: temp=61.5 th3: temp=58.9 sysload=0.16 cputime=443.622 memavail=7395976 print_time=6105.689 buffer_time=2.019 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 122 Hz
Stats 6082.0: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26949566 bytes_read=4285519 bytes_retransmit=9 bytes_invalid=0 send_seq=512011 receive_seq=512011 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=52 upcoming_bytes=8089 freq=400015928 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37708 bytes_read=118121 bytes_retransmit=0 bytes_invalid=0 send_seq=6256 receive_seq=6256 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997266 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=181166 bytes_read=5698415 bytes_retransmit=9 bytes_invalid=0 send_seq=25136 receive_seq=25136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997625 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115620 bytes_read=2923353 bytes_retransmit=9 bytes_invalid=0 send_seq=15867 receive_seq=15867 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37975 bytes_read=1552441 bytes_retransmit=9 bytes_invalid=0 send_seq=6270 receive_seq=6270 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38461 bytes_read=115822 bytes_retransmit=9 bytes_invalid=0 send_seq=6257 receive_seq=6257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92553 bytes_read=2391664 bytes_retransmit=0 bytes_invalid=0 send_seq=10816 receive_seq=10816 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998641 coil_temp=16.8 refs=0 mcu_temp=20.18 supply_voltage=3.011 th0: temp=55.2 th1: temp=54.3 th2: temp=61.4 th3: temp=59.1 sysload=0.16 cputime=443.779 memavail=7394964 print_time=6106.885 buffer_time=2.216 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 123 Hz
Stats 6083.0: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26958420 bytes_read=4286624 bytes_retransmit=9 bytes_invalid=0 send_seq=512170 receive_seq=512170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=5884 freq=400015930 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37714 bytes_read=118150 bytes_retransmit=0 bytes_invalid=0 send_seq=6257 receive_seq=6257 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997259 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=181242 bytes_read=5701514 bytes_retransmit=9 bytes_invalid=0 send_seq=25147 receive_seq=25147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997613 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115626 bytes_read=2923479 bytes_retransmit=9 bytes_invalid=0 send_seq=15868 receive_seq=15868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997502 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=37981 bytes_read=1552735 bytes_retransmit=9 bytes_invalid=0 send_seq=6271 receive_seq=6271 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38467 bytes_read=115838 bytes_retransmit=9 bytes_invalid=0 send_seq=6258 receive_seq=6258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92559 bytes_read=2392020 bytes_retransmit=0 bytes_invalid=0 send_seq=10817 receive_seq=10817 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998636 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=55.1 th1: temp=54.3 th2: temp=61.2 th3: temp=59.1 sysload=0.16 cputime=443.913 memavail=7396904 print_time=6107.764 buffer_time=2.094 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 124 Hz
Stats 6084.0: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26965661 bytes_read=4287589 bytes_retransmit=9 bytes_invalid=0 send_seq=512301 receive_seq=512301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=6933 freq=400015927 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37720 bytes_read=118166 bytes_retransmit=0 bytes_invalid=0 send_seq=6258 receive_seq=6258 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997287 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=181318 bytes_read=5704555 bytes_retransmit=9 bytes_invalid=0 send_seq=25158 receive_seq=25158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997604 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115632 bytes_read=2923572 bytes_retransmit=9 bytes_invalid=0 send_seq=15869 receive_seq=15869 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37987 bytes_read=1552984 bytes_retransmit=9 bytes_invalid=0 send_seq=6272 receive_seq=6272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38473 bytes_read=115854 bytes_retransmit=9 bytes_invalid=0 send_seq=6259 receive_seq=6259 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92565 bytes_read=2392376 bytes_retransmit=0 bytes_invalid=0 send_seq=10818 receive_seq=10818 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998630 coil_temp=16.8 refs=0 mcu_temp=20.18 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.5 th2: temp=61.5 th3: temp=59.1 sysload=0.16 cputime=444.044 memavail=7396904 print_time=6108.690 buffer_time=2.019 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 125 Hz
Stats 6085.0: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26974125 bytes_read=4288683 bytes_retransmit=9 bytes_invalid=0 send_seq=512452 receive_seq=512452 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=8099 freq=400015916 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37726 bytes_read=118182 bytes_retransmit=0 bytes_invalid=0 send_seq=6259 receive_seq=6259 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997296 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=181394 bytes_read=5707595 bytes_retransmit=9 bytes_invalid=0 send_seq=25169 receive_seq=25169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997614 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115638 bytes_read=2923665 bytes_retransmit=9 bytes_invalid=0 send_seq=15870 receive_seq=15870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37993 bytes_read=1553218 bytes_retransmit=9 bytes_invalid=0 send_seq=6273 receive_seq=6273 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38479 bytes_read=115870 bytes_retransmit=9 bytes_invalid=0 send_seq=6260 receive_seq=6260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92571 bytes_read=2392732 bytes_retransmit=0 bytes_invalid=0 send_seq=10819 receive_seq=10819 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998644 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=55.2 th1: temp=54.3 th2: temp=61.5 th3: temp=59.0 sysload=0.15 cputime=444.189 memavail=7396904 print_time=6109.891 buffer_time=2.219 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 126 Hz
Stats 6086.0: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26982981 bytes_read=4289763 bytes_retransmit=9 bytes_invalid=0 send_seq=512607 receive_seq=512606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=5828 freq=400015935 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37732 bytes_read=118198 bytes_retransmit=0 bytes_invalid=0 send_seq=6260 receive_seq=6260 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997298 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=181470 bytes_read=5710663 bytes_retransmit=9 bytes_invalid=0 send_seq=25180 receive_seq=25180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997691 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115644 bytes_read=2923784 bytes_retransmit=9 bytes_invalid=0 send_seq=15871 receive_seq=15871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997536 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=37999 bytes_read=1553512 bytes_retransmit=9 bytes_invalid=0 send_seq=6274 receive_seq=6274 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997713 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38485 bytes_read=115886 bytes_retransmit=9 bytes_invalid=0 send_seq=6261 receive_seq=6261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92577 bytes_read=2393088 bytes_retransmit=0 bytes_invalid=0 send_seq=10820 receive_seq=10820 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998649 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.3 th2: temp=61.5 th3: temp=58.9 sysload=0.15 cputime=444.323 memavail=7396652 print_time=6110.764 buffer_time=2.092 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 127 Hz
Stats 6087.0: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26990234 bytes_read=4290740 bytes_retransmit=9 bytes_invalid=0 send_seq=512737 receive_seq=512737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=6917 freq=400015935 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37738 bytes_read=118214 bytes_retransmit=0 bytes_invalid=0 send_seq=6261 receive_seq=6261 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997264 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=181546 bytes_read=5713704 bytes_retransmit=9 bytes_invalid=0 send_seq=25191 receive_seq=25191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997655 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115650 bytes_read=2923891 bytes_retransmit=9 bytes_invalid=0 send_seq=15872 receive_seq=15872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997537 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38005 bytes_read=1553746 bytes_retransmit=9 bytes_invalid=0 send_seq=6275 receive_seq=6275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38491 bytes_read=115913 bytes_retransmit=9 bytes_invalid=0 send_seq=6262 receive_seq=6262 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92583 bytes_read=2393444 bytes_retransmit=0 bytes_invalid=0 send_seq=10821 receive_seq=10821 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998625 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.4 th2: temp=61.6 th3: temp=59.1 sysload=0.15 cputime=444.452 memavail=7396652 print_time=6111.694 buffer_time=2.021 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 128 Hz
Stats 6088.0: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=26998578 bytes_read=4291821 bytes_retransmit=9 bytes_invalid=0 send_seq=512886 receive_seq=512886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=8310 freq=400015921 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37744 bytes_read=118243 bytes_retransmit=0 bytes_invalid=0 send_seq=6262 receive_seq=6262 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997265 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=181622 bytes_read=5716775 bytes_retransmit=9 bytes_invalid=0 send_seq=25202 receive_seq=25202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997650 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115656 bytes_read=2923990 bytes_retransmit=9 bytes_invalid=0 send_seq=15873 receive_seq=15873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997525 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38011 bytes_read=1553980 bytes_retransmit=9 bytes_invalid=0 send_seq=6276 receive_seq=6276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38497 bytes_read=115929 bytes_retransmit=9 bytes_invalid=0 send_seq=6263 receive_seq=6263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92589 bytes_read=2393800 bytes_retransmit=0 bytes_invalid=0 send_seq=10822 receive_seq=10822 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998647 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.2 th2: temp=61.6 th3: temp=59.2 sysload=0.15 cputime=444.598 memavail=7394712 print_time=6112.895 buffer_time=2.221 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 129 Hz
Stats 6089.0: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27007497 bytes_read=4292931 bytes_retransmit=9 bytes_invalid=0 send_seq=513046 receive_seq=513046 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=6103 freq=400015955 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37750 bytes_read=118259 bytes_retransmit=0 bytes_invalid=0 send_seq=6263 receive_seq=6263 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997274 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=181698 bytes_read=5719918 bytes_retransmit=9 bytes_invalid=0 send_seq=25213 receive_seq=25213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997801 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115662 bytes_read=2924118 bytes_retransmit=9 bytes_invalid=0 send_seq=15874 receive_seq=15874 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38017 bytes_read=1554289 bytes_retransmit=9 bytes_invalid=0 send_seq=6277 receive_seq=6277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997689 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38503 bytes_read=115945 bytes_retransmit=9 bytes_invalid=0 send_seq=6264 receive_seq=6264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92595 bytes_read=2394156 bytes_retransmit=0 bytes_invalid=0 send_seq=10823 receive_seq=10823 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998655 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=55.2 th1: temp=54.5 th2: temp=61.6 th3: temp=59.0 sysload=0.15 cputime=444.728 memavail=7394712 print_time=6113.772 buffer_time=2.097 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 130 Hz
Stats 6090.0: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27014917 bytes_read=4293911 bytes_retransmit=9 bytes_invalid=0 send_seq=513180 receive_seq=513180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=7198 freq=400015937 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37756 bytes_read=118275 bytes_retransmit=0 bytes_invalid=0 send_seq=6264 receive_seq=6264 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997277 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=181767 bytes_read=5722953 bytes_retransmit=9 bytes_invalid=0 send_seq=25223 receive_seq=25223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997705 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115668 bytes_read=2924218 bytes_retransmit=9 bytes_invalid=0 send_seq=15875 receive_seq=15875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38023 bytes_read=1554523 bytes_retransmit=9 bytes_invalid=0 send_seq=6278 receive_seq=6278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38509 bytes_read=115961 bytes_retransmit=9 bytes_invalid=0 send_seq=6265 receive_seq=6265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92601 bytes_read=2394512 bytes_retransmit=0 bytes_invalid=0 send_seq=10824 receive_seq=10824 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998616 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.4 th2: temp=61.6 th3: temp=59.1 sysload=0.13 cputime=444.855 memavail=7394712 print_time=6114.700 buffer_time=2.025 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 131 Hz
Stats 6091.0: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27023395 bytes_read=4295005 bytes_retransmit=9 bytes_invalid=0 send_seq=513331 receive_seq=513331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=8484 freq=400015938 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37762 bytes_read=118291 bytes_retransmit=0 bytes_invalid=0 send_seq=6265 receive_seq=6265 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997281 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=181843 bytes_read=5726010 bytes_retransmit=9 bytes_invalid=0 send_seq=25234 receive_seq=25234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997713 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115674 bytes_read=2924318 bytes_retransmit=9 bytes_invalid=0 send_seq=15876 receive_seq=15876 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38029 bytes_read=1554757 bytes_retransmit=9 bytes_invalid=0 send_seq=6279 receive_seq=6279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38515 bytes_read=115977 bytes_retransmit=9 bytes_invalid=0 send_seq=6266 receive_seq=6266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92607 bytes_read=2394868 bytes_retransmit=0 bytes_invalid=0 send_seq=10825 receive_seq=10825 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998635 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=55.2 th1: temp=54.5 th2: temp=61.4 th3: temp=59.0 sysload=0.13 cputime=445.000 memavail=7394732 print_time=6115.898 buffer_time=2.223 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.2 pwm=0.000
Testing frequency 132 Hz
Stats 6092.0: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27032474 bytes_read=4296146 bytes_retransmit=9 bytes_invalid=0 send_seq=513494 receive_seq=513494 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=6213 freq=400015932 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37768 bytes_read=118307 bytes_retransmit=0 bytes_invalid=0 send_seq=6266 receive_seq=6266 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997268 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=181919 bytes_read=5729095 bytes_retransmit=9 bytes_invalid=0 send_seq=25245 receive_seq=25245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997694 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115680 bytes_read=2924460 bytes_retransmit=9 bytes_invalid=0 send_seq=15877 receive_seq=15877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997508 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38035 bytes_read=1555051 bytes_retransmit=9 bytes_invalid=0 send_seq=6280 receive_seq=6280 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38521 bytes_read=116004 bytes_retransmit=9 bytes_invalid=0 send_seq=6267 receive_seq=6267 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92613 bytes_read=2395224 bytes_retransmit=0 bytes_invalid=0 send_seq=10826 receive_seq=10826 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998636 coil_temp=16.8 refs=0 mcu_temp=20.18 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.1 th2: temp=61.7 th3: temp=59.1 sysload=0.13 cputime=445.134 memavail=7394732 print_time=6116.771 buffer_time=2.095 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Stats 6093.0: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27039931 bytes_read=4297121 bytes_retransmit=9 bytes_invalid=0 send_seq=513627 receive_seq=513627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=3441 freq=400015933 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37774 bytes_read=118336 bytes_retransmit=0 bytes_invalid=0 send_seq=6267 receive_seq=6267 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997273 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=181995 bytes_read=5732170 bytes_retransmit=9 bytes_invalid=0 send_seq=25256 receive_seq=25256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997687 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115686 bytes_read=2924560 bytes_retransmit=9 bytes_invalid=0 send_seq=15878 receive_seq=15878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38041 bytes_read=1555285 bytes_retransmit=9 bytes_invalid=0 send_seq=6281 receive_seq=6281 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38527 bytes_read=116020 bytes_retransmit=9 bytes_invalid=0 send_seq=6268 receive_seq=6268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92619 bytes_read=2395580 bytes_retransmit=0 bytes_invalid=0 send_seq=10827 receive_seq=10827 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998670 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.5 th2: temp=61.6 th3: temp=59.2 sysload=0.13 cputime=445.238 memavail=7394732 print_time=6117.148 buffer_time=1.471 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6094.0: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27043964 bytes_read=4297871 bytes_retransmit=9 bytes_invalid=0 send_seq=513707 receive_seq=513707 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015929 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37786 bytes_read=118368 bytes_retransmit=0 bytes_invalid=0 send_seq=6269 receive_seq=6269 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997275 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=182077 bytes_read=5735244 bytes_retransmit=9 bytes_invalid=0 send_seq=25268 receive_seq=25268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997664 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115698 bytes_read=2924676 bytes_retransmit=9 bytes_invalid=0 send_seq=15880 receive_seq=15880 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997514 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38053 bytes_read=1555550 bytes_retransmit=9 bytes_invalid=0 send_seq=6283 receive_seq=6283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38539 bytes_read=116052 bytes_retransmit=9 bytes_invalid=0 send_seq=6270 receive_seq=6270 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92631 bytes_read=2395952 bytes_retransmit=0 bytes_invalid=0 send_seq=10829 receive_seq=10829 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998658 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.3 th2: temp=61.7 th3: temp=59.1 sysload=0.13 cputime=445.312 memavail=7394732 print_time=6117.148 buffer_time=0.470 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
LIS2DW finished 'toolboard_t0' measurements
Resonances data written to /tmp/resonances_x_125.000_250.000_20.000_t0_copy.csv file
Probing point (125.000, 250.000, 20.000)
Stats 6095.0: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27044370 bytes_read=4298306 bytes_retransmit=9 bytes_invalid=0 send_seq=513732 receive_seq=513732 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015924 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37792 bytes_read=118384 bytes_retransmit=0 bytes_invalid=0 send_seq=6270 receive_seq=6270 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997269 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=182173 bytes_read=5737121 bytes_retransmit=9 bytes_invalid=0 send_seq=25280 receive_seq=25280 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997643 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115704 bytes_read=2924804 bytes_retransmit=9 bytes_invalid=0 send_seq=15881 receive_seq=15881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38059 bytes_read=1555844 bytes_retransmit=9 bytes_invalid=0 send_seq=6284 receive_seq=6284 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997629 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38545 bytes_read=116068 bytes_retransmit=9 bytes_invalid=0 send_seq=6271 receive_seq=6271 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92637 bytes_read=2396308 bytes_retransmit=0 bytes_invalid=0 send_seq=10830 receive_seq=10830 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998649 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.4 th2: temp=61.7 th3: temp=59.1 sysload=0.28 cputime=445.428 memavail=7396396 print_time=6118.131 buffer_time=0.453 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t0' measurements
toolhead: max_velocity: 600.000000
max_accel: 8379.841000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance testing
Testing frequency 10 Hz
Testing frequency 11 Hz
Testing frequency 12 Hz
Stats 6096.0: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27053624 bytes_read=4299466 bytes_retransmit=9 bytes_invalid=0 send_seq=513902 receive_seq=513902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=432 freq=400015909 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37798 bytes_read=118400 bytes_retransmit=0 bytes_invalid=0 send_seq=6271 receive_seq=6271 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997281 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=182321 bytes_read=5738822 bytes_retransmit=9 bytes_invalid=0 send_seq=25297 receive_seq=25297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997753 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115710 bytes_read=2924904 bytes_retransmit=9 bytes_invalid=0 send_seq=15882 receive_seq=15882 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997517 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38065 bytes_read=1556078 bytes_retransmit=9 bytes_invalid=0 send_seq=6285 receive_seq=6285 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38551 bytes_read=116084 bytes_retransmit=9 bytes_invalid=0 send_seq=6272 receive_seq=6272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92643 bytes_read=2396664 bytes_retransmit=0 bytes_invalid=0 send_seq=10831 receive_seq=10831 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998656 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.6 th2: temp=61.6 th3: temp=59.1 sysload=0.28 cputime=445.615 memavail=7396396 print_time=6121.295 buffer_time=2.615 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6097.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=27056735 bytes_read=4300156 bytes_retransmit=9 bytes_invalid=0 send_seq=513969 receive_seq=513969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=205 freq=400015912 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37804 bytes_read=118416 bytes_retransmit=0 bytes_invalid=0 send_seq=6272 receive_seq=6272 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997274 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=182397 bytes_read=5741879 bytes_retransmit=9 bytes_invalid=0 send_seq=25308 receive_seq=25308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997837 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115716 bytes_read=2925018 bytes_retransmit=9 bytes_invalid=0 send_seq=15883 receive_seq=15883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997525 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38071 bytes_read=1556312 bytes_retransmit=9 bytes_invalid=0 send_seq=6286 receive_seq=6286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38557 bytes_read=116111 bytes_retransmit=9 bytes_invalid=0 send_seq=6273 receive_seq=6273 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92649 bytes_read=2397020 bytes_retransmit=0 bytes_invalid=0 send_seq=10832 receive_seq=10832 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998671 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.6 th2: temp=61.5 th3: temp=59.0 sysload=0.28 cputime=445.692 memavail=7396416 print_time=6121.888 buffer_time=2.208 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 13 Hz
Stats 6098.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=27060454 bytes_read=4300826 bytes_retransmit=9 bytes_invalid=0 send_seq=514042 receive_seq=514042 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015914 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37810 bytes_read=118445 bytes_retransmit=0 bytes_invalid=0 send_seq=6273 receive_seq=6273 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997265 toolboard_t0: mcu_awake=0.260 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=182473 bytes_read=5744952 bytes_retransmit=9 bytes_invalid=0 send_seq=25319 receive_seq=25319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997813 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115722 bytes_read=2925146 bytes_retransmit=9 bytes_invalid=0 send_seq=15884 receive_seq=15884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38077 bytes_read=1556606 bytes_retransmit=9 bytes_invalid=0 send_seq=6287 receive_seq=6287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38563 bytes_read=116127 bytes_retransmit=9 bytes_invalid=0 send_seq=6274 receive_seq=6274 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92655 bytes_read=2397376 bytes_retransmit=0 bytes_invalid=0 send_seq=10833 receive_seq=10833 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998663 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.4 th2: temp=61.5 th3: temp=59.0 sysload=0.28 cputime=445.778 memavail=7394444 print_time=6122.731 buffer_time=2.050 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 14 Hz
Stats 6099.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=27065102 bytes_read=4301586 bytes_retransmit=9 bytes_invalid=0 send_seq=514132 receive_seq=514132 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=495 freq=400015903 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37816 bytes_read=118461 bytes_retransmit=0 bytes_invalid=0 send_seq=6274 receive_seq=6274 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997258 toolboard_t0: mcu_awake=0.260 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=182549 bytes_read=5748008 bytes_retransmit=9 bytes_invalid=0 send_seq=25330 receive_seq=25330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997783 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115728 bytes_read=2925246 bytes_retransmit=9 bytes_invalid=0 send_seq=15885 receive_seq=15885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38083 bytes_read=1556855 bytes_retransmit=9 bytes_invalid=0 send_seq=6288 receive_seq=6288 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38569 bytes_read=116143 bytes_retransmit=9 bytes_invalid=0 send_seq=6275 receive_seq=6275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92661 bytes_read=2397732 bytes_retransmit=0 bytes_invalid=0 send_seq=10834 receive_seq=10834 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998661 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.5 th2: temp=61.5 th3: temp=59.1 sysload=0.28 cputime=445.874 memavail=7389172 print_time=6123.730 buffer_time=2.048 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 15 Hz
Testing frequency 16 Hz
Stats 6100.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=27069857 bytes_read=4302380 bytes_retransmit=9 bytes_invalid=0 send_seq=514223 receive_seq=514223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=1816 freq=400015901 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37822 bytes_read=118477 bytes_retransmit=0 bytes_invalid=0 send_seq=6275 receive_seq=6275 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997276 toolboard_t0: mcu_awake=0.260 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=182625 bytes_read=5751066 bytes_retransmit=9 bytes_invalid=0 send_seq=25341 receive_seq=25341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997764 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115734 bytes_read=2925346 bytes_retransmit=9 bytes_invalid=0 send_seq=15886 receive_seq=15886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997514 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38089 bytes_read=1557089 bytes_retransmit=9 bytes_invalid=0 send_seq=6289 receive_seq=6289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38575 bytes_read=116159 bytes_retransmit=9 bytes_invalid=0 send_seq=6276 receive_seq=6276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92667 bytes_read=2398088 bytes_retransmit=0 bytes_invalid=0 send_seq=10835 receive_seq=10835 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998668 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.3 th2: temp=61.4 th3: temp=59.1 sysload=0.26 cputime=445.973 memavail=7395036 print_time=6124.980 buffer_time=2.298 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 6101.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=27075079 bytes_read=4303185 bytes_retransmit=9 bytes_invalid=0 send_seq=514322 receive_seq=514322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=856 freq=400015894 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37828 bytes_read=118493 bytes_retransmit=0 bytes_invalid=0 send_seq=6276 receive_seq=6276 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997262 toolboard_t0: mcu_awake=0.260 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=182694 bytes_read=5754128 bytes_retransmit=9 bytes_invalid=0 send_seq=25351 receive_seq=25351 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997739 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115740 bytes_read=2925474 bytes_retransmit=9 bytes_invalid=0 send_seq=15887 receive_seq=15887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38095 bytes_read=1557383 bytes_retransmit=9 bytes_invalid=0 send_seq=6290 receive_seq=6290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38581 bytes_read=116175 bytes_retransmit=9 bytes_invalid=0 send_seq=6277 receive_seq=6277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92673 bytes_read=2398444 bytes_retransmit=0 bytes_invalid=0 send_seq=10836 receive_seq=10836 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998770 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.4 th2: temp=61.3 th3: temp=58.9 sysload=0.26 cputime=446.064 memavail=7395036 print_time=6125.861 buffer_time=2.178 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 17 Hz
Stats 6102.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=27079560 bytes_read=4303941 bytes_retransmit=9 bytes_invalid=0 send_seq=514408 receive_seq=514408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=1884 freq=400015902 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37834 bytes_read=118509 bytes_retransmit=0 bytes_invalid=0 send_seq=6277 receive_seq=6277 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997269 toolboard_t0: mcu_awake=0.260 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=182770 bytes_read=5757184 bytes_retransmit=9 bytes_invalid=0 send_seq=25362 receive_seq=25362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997720 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115746 bytes_read=2925588 bytes_retransmit=9 bytes_invalid=0 send_seq=15888 receive_seq=15888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997533 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38101 bytes_read=1557617 bytes_retransmit=9 bytes_invalid=0 send_seq=6291 receive_seq=6291 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38587 bytes_read=116202 bytes_retransmit=9 bytes_invalid=0 send_seq=6278 receive_seq=6278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92679 bytes_read=2398800 bytes_retransmit=0 bytes_invalid=0 send_seq=10837 receive_seq=10837 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998750 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.5 th2: temp=61.2 th3: temp=58.9 sysload=0.26 cputime=446.153 memavail=7395036 print_time=6126.782 buffer_time=2.098 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 18 Hz
Stats 6103.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=27084947 bytes_read=4304770 bytes_retransmit=9 bytes_invalid=0 send_seq=514506 receive_seq=514506 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=1180 freq=400015915 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37840 bytes_read=118538 bytes_retransmit=0 bytes_invalid=0 send_seq=6278 receive_seq=6278 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997253 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=182846 bytes_read=5760260 bytes_retransmit=9 bytes_invalid=0 send_seq=25373 receive_seq=25373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997735 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115752 bytes_read=2925688 bytes_retransmit=9 bytes_invalid=0 send_seq=15889 receive_seq=15889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997565 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38107 bytes_read=1557851 bytes_retransmit=9 bytes_invalid=0 send_seq=6292 receive_seq=6292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38593 bytes_read=116218 bytes_retransmit=9 bytes_invalid=0 send_seq=6279 receive_seq=6279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92685 bytes_read=2399156 bytes_retransmit=0 bytes_invalid=0 send_seq=10838 receive_seq=10838 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998717 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.6 th2: temp=61.2 th3: temp=58.9 sysload=0.26 cputime=446.248 memavail=7395036 print_time=6127.745 buffer_time=2.061 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 19 Hz
Testing frequency 20 Hz
Stats 6104.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=27090760 bytes_read=4305615 bytes_retransmit=9 bytes_invalid=0 send_seq=514613 receive_seq=514613 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=2255 freq=400015924 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37846 bytes_read=118554 bytes_retransmit=0 bytes_invalid=0 send_seq=6279 receive_seq=6279 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997230 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=182922 bytes_read=5763403 bytes_retransmit=9 bytes_invalid=0 send_seq=25384 receive_seq=25384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997666 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115758 bytes_read=2925816 bytes_retransmit=9 bytes_invalid=0 send_seq=15890 receive_seq=15890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997521 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38113 bytes_read=1558160 bytes_retransmit=9 bytes_invalid=0 send_seq=6293 receive_seq=6293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38599 bytes_read=116234 bytes_retransmit=9 bytes_invalid=0 send_seq=6280 receive_seq=6280 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92691 bytes_read=2399512 bytes_retransmit=0 bytes_invalid=0 send_seq=10839 receive_seq=10839 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998694 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.2 th1: temp=54.6 th2: temp=61.2 th3: temp=58.7 sysload=0.26 cputime=446.351 memavail=7395036 print_time=6128.935 buffer_time=2.250 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6105.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=27095712 bytes_read=4306395 bytes_retransmit=9 bytes_invalid=0 send_seq=514707 receive_seq=514707 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=3136 freq=400015928 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37852 bytes_read=118570 bytes_retransmit=0 bytes_invalid=0 send_seq=6280 receive_seq=6280 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997246 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=182998 bytes_read=5766460 bytes_retransmit=9 bytes_invalid=0 send_seq=25395 receive_seq=25395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997631 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115764 bytes_read=2925916 bytes_retransmit=9 bytes_invalid=0 send_seq=15891 receive_seq=15891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38119 bytes_read=1558394 bytes_retransmit=9 bytes_invalid=0 send_seq=6294 receive_seq=6294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997615 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38605 bytes_read=116250 bytes_retransmit=9 bytes_invalid=0 send_seq=6281 receive_seq=6281 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92697 bytes_read=2399868 bytes_retransmit=0 bytes_invalid=0 send_seq=10840 receive_seq=10840 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998664 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.5 th2: temp=61.1 th3: temp=58.7 sysload=0.24 cputime=446.441 memavail=7395036 print_time=6129.807 buffer_time=2.121 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 21 Hz
Stats 6106.0: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=27101995 bytes_read=4307314 bytes_retransmit=9 bytes_invalid=0 send_seq=514823 receive_seq=514823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=2041 freq=400015919 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37858 bytes_read=118586 bytes_retransmit=0 bytes_invalid=0 send_seq=6281 receive_seq=6281 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997242 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=183074 bytes_read=5769531 bytes_retransmit=9 bytes_invalid=0 send_seq=25406 receive_seq=25406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997601 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115770 bytes_read=2926016 bytes_retransmit=9 bytes_invalid=0 send_seq=15892 receive_seq=15892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997477 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38125 bytes_read=1558628 bytes_retransmit=9 bytes_invalid=0 send_seq=6295 receive_seq=6295 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997605 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38611 bytes_read=116266 bytes_retransmit=9 bytes_invalid=0 send_seq=6282 receive_seq=6282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92703 bytes_read=2400224 bytes_retransmit=0 bytes_invalid=0 send_seq=10841 receive_seq=10841 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998650 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.3 th2: temp=61.2 th3: temp=58.6 sysload=0.24 cputime=446.538 memavail=7395036 print_time=6130.756 buffer_time=2.069 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 22 Hz
Testing frequency 23 Hz
Stats 6107.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=27108210 bytes_read=4308200 bytes_retransmit=9 bytes_invalid=0 send_seq=514935 receive_seq=514935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=3224 freq=400015919 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37864 bytes_read=118601 bytes_retransmit=0 bytes_invalid=0 send_seq=6282 receive_seq=6282 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997246 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=183150 bytes_read=5772603 bytes_retransmit=9 bytes_invalid=0 send_seq=25417 receive_seq=25417 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997629 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115776 bytes_read=2926158 bytes_retransmit=9 bytes_invalid=0 send_seq=15893 receive_seq=15893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997491 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38131 bytes_read=1558922 bytes_retransmit=9 bytes_invalid=0 send_seq=6296 receive_seq=6296 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38617 bytes_read=116293 bytes_retransmit=9 bytes_invalid=0 send_seq=6283 receive_seq=6283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92709 bytes_read=2400580 bytes_retransmit=0 bytes_invalid=0 send_seq=10842 receive_seq=10842 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998661 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.5 th2: temp=61.0 th3: temp=58.6 sysload=0.24 cputime=446.644 memavail=7395036 print_time=6131.950 buffer_time=2.263 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 6108.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=27113506 bytes_read=4309010 bytes_retransmit=9 bytes_invalid=0 send_seq=515035 receive_seq=515035 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=4263 freq=400015909 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37870 bytes_read=118629 bytes_retransmit=0 bytes_invalid=0 send_seq=6283 receive_seq=6283 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997238 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=183226 bytes_read=5775678 bytes_retransmit=9 bytes_invalid=0 send_seq=25428 receive_seq=25428 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997627 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115782 bytes_read=2926258 bytes_retransmit=9 bytes_invalid=0 send_seq=15894 receive_seq=15894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997488 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38137 bytes_read=1559156 bytes_retransmit=9 bytes_invalid=0 send_seq=6297 receive_seq=6297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997649 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38623 bytes_read=116309 bytes_retransmit=9 bytes_invalid=0 send_seq=6284 receive_seq=6284 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92715 bytes_read=2400936 bytes_retransmit=0 bytes_invalid=0 send_seq=10843 receive_seq=10843 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998663 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.5 th2: temp=60.9 th3: temp=58.5 sysload=0.24 cputime=446.739 memavail=7394332 print_time=6132.835 buffer_time=2.147 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 24 Hz
Stats 6109.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=27120287 bytes_read=4309954 bytes_retransmit=9 bytes_invalid=0 send_seq=515157 receive_seq=515157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=3429 freq=400015910 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37876 bytes_read=118644 bytes_retransmit=0 bytes_invalid=0 send_seq=6284 receive_seq=6284 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997245 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=183302 bytes_read=5778748 bytes_retransmit=9 bytes_invalid=0 send_seq=25439 receive_seq=25439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997632 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115788 bytes_read=2926358 bytes_retransmit=9 bytes_invalid=0 send_seq=15895 receive_seq=15895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997501 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38143 bytes_read=1559405 bytes_retransmit=9 bytes_invalid=0 send_seq=6298 receive_seq=6298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38629 bytes_read=116325 bytes_retransmit=9 bytes_invalid=0 send_seq=6285 receive_seq=6285 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92721 bytes_read=2401292 bytes_retransmit=0 bytes_invalid=0 send_seq=10844 receive_seq=10844 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998669 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.6 th1: temp=54.5 th2: temp=60.9 th3: temp=58.4 sysload=0.24 cputime=446.839 memavail=7394332 print_time=6133.800 buffer_time=2.111 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 25 Hz
Testing frequency 26 Hz
Stats 6110.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=27127147 bytes_read=4310894 bytes_retransmit=9 bytes_invalid=0 send_seq=515283 receive_seq=515283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=4968 freq=400015901 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37882 bytes_read=118659 bytes_retransmit=0 bytes_invalid=0 send_seq=6285 receive_seq=6285 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997246 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=183378 bytes_read=5781820 bytes_retransmit=9 bytes_invalid=0 send_seq=25450 receive_seq=25450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997618 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115794 bytes_read=2926486 bytes_retransmit=9 bytes_invalid=0 send_seq=15896 receive_seq=15896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38149 bytes_read=1559699 bytes_retransmit=9 bytes_invalid=0 send_seq=6299 receive_seq=6299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38635 bytes_read=116341 bytes_retransmit=9 bytes_invalid=0 send_seq=6286 receive_seq=6286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92727 bytes_read=2401648 bytes_retransmit=0 bytes_invalid=0 send_seq=10845 receive_seq=10845 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998662 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.6 th2: temp=60.9 th3: temp=58.4 sysload=0.22 cputime=446.948 memavail=7394332 print_time=6135.027 buffer_time=2.338 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 6111.0: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=27132982 bytes_read=4311744 bytes_retransmit=9 bytes_invalid=0 send_seq=515391 receive_seq=515391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=5247 freq=400015907 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37888 bytes_read=118674 bytes_retransmit=0 bytes_invalid=0 send_seq=6286 receive_seq=6286 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997258 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=183454 bytes_read=5784936 bytes_retransmit=9 bytes_invalid=0 send_seq=25461 receive_seq=25461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997647 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115800 bytes_read=2926586 bytes_retransmit=9 bytes_invalid=0 send_seq=15897 receive_seq=15897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997512 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38155 bytes_read=1559933 bytes_retransmit=9 bytes_invalid=0 send_seq=6300 receive_seq=6300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38641 bytes_read=116357 bytes_retransmit=9 bytes_invalid=0 send_seq=6287 receive_seq=6287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92733 bytes_read=2402004 bytes_retransmit=0 bytes_invalid=0 send_seq=10846 receive_seq=10846 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998660 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.5 th2: temp=60.9 th3: temp=58.4 sysload=0.22 cputime=447.044 memavail=7394332 print_time=6135.886 buffer_time=2.196 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 27 Hz
Stats 6112.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27140101 bytes_read=4312749 bytes_retransmit=9 bytes_invalid=0 send_seq=515521 receive_seq=515521 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=5012 freq=400015903 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37894 bytes_read=118689 bytes_retransmit=0 bytes_invalid=0 send_seq=6287 receive_seq=6287 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997258 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=183530 bytes_read=5788006 bytes_retransmit=9 bytes_invalid=0 send_seq=25472 receive_seq=25472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997623 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115806 bytes_read=2926700 bytes_retransmit=9 bytes_invalid=0 send_seq=15898 receive_seq=15898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38161 bytes_read=1560167 bytes_retransmit=9 bytes_invalid=0 send_seq=6301 receive_seq=6301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38647 bytes_read=116384 bytes_retransmit=9 bytes_invalid=0 send_seq=6288 receive_seq=6288 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92739 bytes_read=2402360 bytes_retransmit=0 bytes_invalid=0 send_seq=10847 receive_seq=10847 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998663 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.6 th2: temp=60.8 th3: temp=58.3 sysload=0.22 cputime=447.146 memavail=7394360 print_time=6136.861 buffer_time=2.170 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 28 Hz
Stats 6113.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27147486 bytes_read=4313734 bytes_retransmit=9 bytes_invalid=0 send_seq=515656 receive_seq=515656 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=3819 freq=400015907 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37900 bytes_read=118718 bytes_retransmit=0 bytes_invalid=0 send_seq=6288 receive_seq=6288 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997267 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=183599 bytes_read=5791070 bytes_retransmit=9 bytes_invalid=0 send_seq=25482 receive_seq=25482 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997617 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115812 bytes_read=2926828 bytes_retransmit=9 bytes_invalid=0 send_seq=15899 receive_seq=15899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38167 bytes_read=1560461 bytes_retransmit=9 bytes_invalid=0 send_seq=6302 receive_seq=6302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38653 bytes_read=116400 bytes_retransmit=9 bytes_invalid=0 send_seq=6289 receive_seq=6289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92745 bytes_read=2402716 bytes_retransmit=0 bytes_invalid=0 send_seq=10848 receive_seq=10848 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998661 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.5 th2: temp=60.9 th3: temp=58.2 sysload=0.22 cputime=447.248 memavail=7394360 print_time=6137.725 buffer_time=2.034 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 29 Hz
Testing frequency 30 Hz
Stats 6114.0: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27153554 bytes_read=4314609 bytes_retransmit=9 bytes_invalid=0 send_seq=515769 receive_seq=515769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=6130 freq=400015907 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37906 bytes_read=118734 bytes_retransmit=0 bytes_invalid=0 send_seq=6289 receive_seq=6289 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997251 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=183675 bytes_read=5794128 bytes_retransmit=9 bytes_invalid=0 send_seq=25493 receive_seq=25493 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997695 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115818 bytes_read=2926928 bytes_retransmit=9 bytes_invalid=0 send_seq=15900 receive_seq=15900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997491 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38173 bytes_read=1560710 bytes_retransmit=9 bytes_invalid=0 send_seq=6303 receive_seq=6303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38659 bytes_read=116416 bytes_retransmit=9 bytes_invalid=0 send_seq=6290 receive_seq=6290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92751 bytes_read=2403072 bytes_retransmit=0 bytes_invalid=0 send_seq=10849 receive_seq=10849 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998646 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.3 th2: temp=60.6 th3: temp=58.2 sysload=0.22 cputime=447.357 memavail=7394360 print_time=6138.917 buffer_time=2.225 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6115.1: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27161105 bytes_read=4315633 bytes_retransmit=9 bytes_invalid=0 send_seq=515906 receive_seq=515906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=5983 freq=400015903 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37912 bytes_read=118750 bytes_retransmit=0 bytes_invalid=0 send_seq=6290 receive_seq=6290 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997240 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=183751 bytes_read=5797199 bytes_retransmit=9 bytes_invalid=0 send_seq=25504 receive_seq=25504 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997674 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115824 bytes_read=2927028 bytes_retransmit=9 bytes_invalid=0 send_seq=15901 receive_seq=15901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38179 bytes_read=1560944 bytes_retransmit=9 bytes_invalid=0 send_seq=6304 receive_seq=6304 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38665 bytes_read=116432 bytes_retransmit=9 bytes_invalid=0 send_seq=6291 receive_seq=6291 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92757 bytes_read=2403428 bytes_retransmit=0 bytes_invalid=0 send_seq=10850 receive_seq=10850 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998656 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.4 th2: temp=60.8 th3: temp=58.2 sysload=0.20 cputime=447.458 memavail=7394360 print_time=6139.878 buffer_time=2.185 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 31 Hz
Stats 6116.1: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27168914 bytes_read=4316648 bytes_retransmit=9 bytes_invalid=0 send_seq=516047 receive_seq=516047 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=36 upcoming_bytes=4452 freq=400015906 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37918 bytes_read=118766 bytes_retransmit=0 bytes_invalid=0 send_seq=6291 receive_seq=6291 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997232 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=183827 bytes_read=5800271 bytes_retransmit=9 bytes_invalid=0 send_seq=25515 receive_seq=25515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997676 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115830 bytes_read=2927156 bytes_retransmit=9 bytes_invalid=0 send_seq=15902 receive_seq=15902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997518 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38185 bytes_read=1561238 bytes_retransmit=9 bytes_invalid=0 send_seq=6305 receive_seq=6305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38671 bytes_read=116448 bytes_retransmit=9 bytes_invalid=0 send_seq=6292 receive_seq=6292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92763 bytes_read=2403784 bytes_retransmit=0 bytes_invalid=0 send_seq=10851 receive_seq=10851 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998650 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.6 th2: temp=60.7 th3: temp=58.3 sysload=0.20 cputime=447.569 memavail=7389848 print_time=6140.747 buffer_time=2.053 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 32 Hz
Testing frequency 33 Hz
Stats 6117.1: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27175314 bytes_read=4317559 bytes_retransmit=9 bytes_invalid=0 send_seq=516164 receive_seq=516164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=6896 freq=400015942 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37924 bytes_read=118782 bytes_retransmit=0 bytes_invalid=0 send_seq=6292 receive_seq=6292 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997231 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=183903 bytes_read=5803327 bytes_retransmit=9 bytes_invalid=0 send_seq=25526 receive_seq=25526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997645 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115836 bytes_read=2927270 bytes_retransmit=9 bytes_invalid=0 send_seq=15903 receive_seq=15903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997654 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38191 bytes_read=1561472 bytes_retransmit=9 bytes_invalid=0 send_seq=6306 receive_seq=6306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38677 bytes_read=116475 bytes_retransmit=9 bytes_invalid=0 send_seq=6293 receive_seq=6293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92769 bytes_read=2404140 bytes_retransmit=0 bytes_invalid=0 send_seq=10852 receive_seq=10852 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998654 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.7 th2: temp=60.6 th3: temp=58.2 sysload=0.20 cputime=447.683 memavail=7395980 print_time=6141.958 buffer_time=2.264 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6118.1: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27183266 bytes_read=4318603 bytes_retransmit=9 bytes_invalid=0 send_seq=516305 receive_seq=516305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=6976 freq=400015944 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37930 bytes_read=118811 bytes_retransmit=0 bytes_invalid=0 send_seq=6293 receive_seq=6293 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997187 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=183979 bytes_read=5806415 bytes_retransmit=9 bytes_invalid=0 send_seq=25537 receive_seq=25537 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997576 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115842 bytes_read=2927370 bytes_retransmit=9 bytes_invalid=0 send_seq=15904 receive_seq=15904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38197 bytes_read=1561706 bytes_retransmit=9 bytes_invalid=0 send_seq=6307 receive_seq=6307 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997595 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38683 bytes_read=116491 bytes_retransmit=9 bytes_invalid=0 send_seq=6294 receive_seq=6294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92775 bytes_read=2404496 bytes_retransmit=0 bytes_invalid=0 send_seq=10853 receive_seq=10853 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998615 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.4 th2: temp=60.6 th3: temp=58.1 sysload=0.20 cputime=447.786 memavail=7395016 print_time=6142.899 buffer_time=2.205 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 34 Hz
Stats 6119.1: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27191392 bytes_read=4319646 bytes_retransmit=9 bytes_invalid=0 send_seq=516452 receive_seq=516452 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=5400 freq=400015923 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37936 bytes_read=118827 bytes_retransmit=0 bytes_invalid=0 send_seq=6294 receive_seq=6294 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997204 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=184055 bytes_read=5809543 bytes_retransmit=9 bytes_invalid=0 send_seq=25548 receive_seq=25548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997683 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115848 bytes_read=2927498 bytes_retransmit=9 bytes_invalid=0 send_seq=15905 receive_seq=15905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38203 bytes_read=1562015 bytes_retransmit=9 bytes_invalid=0 send_seq=6308 receive_seq=6308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38689 bytes_read=116507 bytes_retransmit=9 bytes_invalid=0 send_seq=6295 receive_seq=6295 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92781 bytes_read=2404852 bytes_retransmit=0 bytes_invalid=0 send_seq=10854 receive_seq=10854 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998616 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.4 th2: temp=60.7 th3: temp=58.2 sysload=0.20 cputime=447.892 memavail=7395016 print_time=6143.793 buffer_time=2.098 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 35 Hz
Stats 6120.1: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27198136 bytes_read=4320573 bytes_retransmit=9 bytes_invalid=0 send_seq=516576 receive_seq=516576 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=6913 freq=400015911 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37942 bytes_read=118843 bytes_retransmit=0 bytes_invalid=0 send_seq=6295 receive_seq=6295 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997237 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=184131 bytes_read=5812603 bytes_retransmit=9 bytes_invalid=0 send_seq=25559 receive_seq=25559 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997699 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115854 bytes_read=2927598 bytes_retransmit=9 bytes_invalid=0 send_seq=15906 receive_seq=15906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997555 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38209 bytes_read=1562249 bytes_retransmit=9 bytes_invalid=0 send_seq=6309 receive_seq=6309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997754 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38695 bytes_read=116523 bytes_retransmit=9 bytes_invalid=0 send_seq=6296 receive_seq=6296 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92787 bytes_read=2405208 bytes_retransmit=0 bytes_invalid=0 send_seq=10855 receive_seq=10855 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998635 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.6 th2: temp=60.4 th3: temp=58.1 sysload=0.19 cputime=447.994 memavail=7395016 print_time=6144.727 buffer_time=2.032 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 36 Hz
Stats 6121.1: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27206565 bytes_read=4321667 bytes_retransmit=9 bytes_invalid=0 send_seq=516727 receive_seq=516727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=8308 freq=400015900 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37948 bytes_read=118859 bytes_retransmit=0 bytes_invalid=0 send_seq=6296 receive_seq=6296 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997253 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=184207 bytes_read=5815675 bytes_retransmit=9 bytes_invalid=0 send_seq=25570 receive_seq=25570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997811 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115860 bytes_read=2927698 bytes_retransmit=9 bytes_invalid=0 send_seq=15907 receive_seq=15907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997560 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38215 bytes_read=1562483 bytes_retransmit=9 bytes_invalid=0 send_seq=6310 receive_seq=6310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997742 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38701 bytes_read=116539 bytes_retransmit=9 bytes_invalid=0 send_seq=6297 receive_seq=6297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92793 bytes_read=2405564 bytes_retransmit=0 bytes_invalid=0 send_seq=10856 receive_seq=10856 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998643 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=55.2 th1: temp=54.6 th2: temp=60.5 th3: temp=58.2 sysload=0.19 cputime=448.108 memavail=7395020 print_time=6145.937 buffer_time=2.241 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 37 Hz
Stats 6122.1: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27215276 bytes_read=4322773 bytes_retransmit=9 bytes_invalid=0 send_seq=516883 receive_seq=516883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=6291 freq=400015924 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37954 bytes_read=118875 bytes_retransmit=0 bytes_invalid=0 send_seq=6297 receive_seq=6297 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997255 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=184283 bytes_read=5818746 bytes_retransmit=9 bytes_invalid=0 send_seq=25581 receive_seq=25581 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997842 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115866 bytes_read=2927840 bytes_retransmit=9 bytes_invalid=0 send_seq=15908 receive_seq=15908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997553 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38221 bytes_read=1562777 bytes_retransmit=9 bytes_invalid=0 send_seq=6311 receive_seq=6311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997737 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38707 bytes_read=116566 bytes_retransmit=9 bytes_invalid=0 send_seq=6298 receive_seq=6298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92799 bytes_read=2405920 bytes_retransmit=0 bytes_invalid=0 send_seq=10857 receive_seq=10857 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998676 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=55.4 th1: temp=54.6 th2: temp=60.4 th3: temp=58.0 sysload=0.19 cputime=448.215 memavail=7395020 print_time=6146.792 buffer_time=2.096 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 38 Hz
Stats 6123.1: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27222396 bytes_read=4323728 bytes_retransmit=9 bytes_invalid=0 send_seq=517012 receive_seq=517012 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=7896 freq=400015946 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37960 bytes_read=118904 bytes_retransmit=0 bytes_invalid=0 send_seq=6298 receive_seq=6298 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997215 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=184359 bytes_read=5821819 bytes_retransmit=9 bytes_invalid=0 send_seq=25592 receive_seq=25592 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997852 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115872 bytes_read=2927940 bytes_retransmit=9 bytes_invalid=0 send_seq=15909 receive_seq=15909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997487 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38227 bytes_read=1563011 bytes_retransmit=9 bytes_invalid=0 send_seq=6312 receive_seq=6312 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38713 bytes_read=116582 bytes_retransmit=9 bytes_invalid=0 send_seq=6299 receive_seq=6299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92805 bytes_read=2406276 bytes_retransmit=0 bytes_invalid=0 send_seq=10858 receive_seq=10858 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998640 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=55.5 th1: temp=54.6 th2: temp=60.4 th3: temp=58.0 sysload=0.19 cputime=448.319 memavail=7395036 print_time=6147.738 buffer_time=2.042 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 39 Hz
Testing frequency 40 Hz
Stats 6124.1: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27231417 bytes_read=4324857 bytes_retransmit=9 bytes_invalid=0 send_seq=517170 receive_seq=517170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=9148 freq=400015948 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37966 bytes_read=118920 bytes_retransmit=0 bytes_invalid=0 send_seq=6299 receive_seq=6299 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997183 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=184435 bytes_read=5824891 bytes_retransmit=9 bytes_invalid=0 send_seq=25603 receive_seq=25603 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000246 adj=63997835 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115878 bytes_read=2928040 bytes_retransmit=9 bytes_invalid=0 send_seq=15910 receive_seq=15910 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997434 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38233 bytes_read=1563260 bytes_retransmit=9 bytes_invalid=0 send_seq=6313 receive_seq=6313 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38719 bytes_read=116598 bytes_retransmit=9 bytes_invalid=0 send_seq=6300 receive_seq=6300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999431 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92811 bytes_read=2406632 bytes_retransmit=0 bytes_invalid=0 send_seq=10859 receive_seq=10859 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998614 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=55.3 th1: temp=54.6 th2: temp=60.4 th3: temp=58.0 sysload=0.19 cputime=448.439 memavail=7395036 print_time=6148.962 buffer_time=2.266 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 6125.1: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27240463 bytes_read=4325982 bytes_retransmit=9 bytes_invalid=0 send_seq=517333 receive_seq=517333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=7320 freq=400015925 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37972 bytes_read=118936 bytes_retransmit=0 bytes_invalid=0 send_seq=6300 receive_seq=6300 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997206 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=184511 bytes_read=5827963 bytes_retransmit=9 bytes_invalid=0 send_seq=25614 receive_seq=25614 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000243 adj=63997892 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115884 bytes_read=2928168 bytes_retransmit=9 bytes_invalid=0 send_seq=15911 receive_seq=15911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997448 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38239 bytes_read=1563554 bytes_retransmit=9 bytes_invalid=0 send_seq=6314 receive_seq=6314 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38725 bytes_read=116614 bytes_retransmit=9 bytes_invalid=0 send_seq=6301 receive_seq=6301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92817 bytes_read=2407006 bytes_retransmit=0 bytes_invalid=0 send_seq=10860 receive_seq=10860 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998622 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=55.5 th1: temp=54.6 th2: temp=60.3 th3: temp=58.0 sysload=0.17 cputime=448.548 memavail=7395036 print_time=6149.840 buffer_time=2.142 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 41 Hz
Stats 6126.1: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27247959 bytes_read=4326977 bytes_retransmit=9 bytes_invalid=0 send_seq=517470 receive_seq=517470 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=9048 freq=400015911 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37978 bytes_read=118952 bytes_retransmit=0 bytes_invalid=0 send_seq=6301 receive_seq=6301 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997245 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=184587 bytes_read=5831078 bytes_retransmit=9 bytes_invalid=0 send_seq=25625 receive_seq=25625 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997878 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115890 bytes_read=2928268 bytes_retransmit=9 bytes_invalid=0 send_seq=15912 receive_seq=15912 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38245 bytes_read=1563788 bytes_retransmit=9 bytes_invalid=0 send_seq=6315 receive_seq=6315 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38731 bytes_read=116630 bytes_retransmit=9 bytes_invalid=0 send_seq=6302 receive_seq=6302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92823 bytes_read=2407362 bytes_retransmit=0 bytes_invalid=0 send_seq=10861 receive_seq=10861 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998641 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.4 th2: temp=60.5 th3: temp=58.0 sysload=0.17 cputime=448.652 memavail=7395036 print_time=6150.765 buffer_time=2.067 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 42 Hz
Testing frequency 43 Hz
Stats 6127.1: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27257344 bytes_read=4328142 bytes_retransmit=9 bytes_invalid=0 send_seq=517632 receive_seq=517632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=10568 freq=400015911 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=37984 bytes_read=118968 bytes_retransmit=0 bytes_invalid=0 send_seq=6302 receive_seq=6302 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997259 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=184656 bytes_read=5834128 bytes_retransmit=9 bytes_invalid=0 send_seq=25635 receive_seq=25635 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997842 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115896 bytes_read=2928382 bytes_retransmit=9 bytes_invalid=0 send_seq=15913 receive_seq=15913 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997522 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38251 bytes_read=1564022 bytes_retransmit=9 bytes_invalid=0 send_seq=6316 receive_seq=6316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38737 bytes_read=116657 bytes_retransmit=9 bytes_invalid=0 send_seq=6303 receive_seq=6303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92829 bytes_read=2407718 bytes_retransmit=0 bytes_invalid=0 send_seq=10862 receive_seq=10862 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998655 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=55.6 th1: temp=54.6 th2: temp=60.4 th3: temp=58.0 sysload=0.17 cputime=448.770 memavail=7395036 print_time=6151.967 buffer_time=2.269 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6128.1: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27267034 bytes_read=4329312 bytes_retransmit=9 bytes_invalid=0 send_seq=517804 receive_seq=517804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=8330 freq=400015899 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37990 bytes_read=118997 bytes_retransmit=0 bytes_invalid=0 send_seq=6303 receive_seq=6303 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997247 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=184732 bytes_read=5837216 bytes_retransmit=9 bytes_invalid=0 send_seq=25646 receive_seq=25646 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997756 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115902 bytes_read=2928510 bytes_retransmit=9 bytes_invalid=0 send_seq=15914 receive_seq=15914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997517 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38257 bytes_read=1564316 bytes_retransmit=9 bytes_invalid=0 send_seq=6317 receive_seq=6317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38743 bytes_read=116673 bytes_retransmit=9 bytes_invalid=0 send_seq=6304 receive_seq=6304 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92835 bytes_read=2408074 bytes_retransmit=0 bytes_invalid=0 send_seq=10863 receive_seq=10863 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998657 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=55.6 th1: temp=54.7 th2: temp=60.4 th3: temp=58.0 sysload=0.17 cputime=448.881 memavail=7395048 print_time=6152.870 buffer_time=2.171 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 44 Hz
Stats 6129.1: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27275195 bytes_read=4330327 bytes_retransmit=9 bytes_invalid=0 send_seq=517945 receive_seq=517945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=9556 freq=400015900 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=37996 bytes_read=119013 bytes_retransmit=0 bytes_invalid=0 send_seq=6304 receive_seq=6304 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999233 adj=49997256 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=184808 bytes_read=5840273 bytes_retransmit=9 bytes_invalid=0 send_seq=25657 receive_seq=25657 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997739 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115908 bytes_read=2928610 bytes_retransmit=9 bytes_invalid=0 send_seq=15915 receive_seq=15915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38263 bytes_read=1564565 bytes_retransmit=9 bytes_invalid=0 send_seq=6318 receive_seq=6318 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38749 bytes_read=116688 bytes_retransmit=9 bytes_invalid=0 send_seq=6305 receive_seq=6305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92841 bytes_read=2408430 bytes_retransmit=0 bytes_invalid=0 send_seq=10864 receive_seq=10864 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998661 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.6 th2: temp=60.3 th3: temp=58.0 sysload=0.17 cputime=448.987 memavail=7395064 print_time=6153.777 buffer_time=2.078 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 45 Hz
Testing frequency 46 Hz
Stats 6130.1: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27284784 bytes_read=4331507 bytes_retransmit=9 bytes_invalid=0 send_seq=518114 receive_seq=518114 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=11229 freq=400015889 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38002 bytes_read=119029 bytes_retransmit=0 bytes_invalid=0 send_seq=6305 receive_seq=6305 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999233 adj=49997243 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=184884 bytes_read=5843343 bytes_retransmit=9 bytes_invalid=0 send_seq=25668 receive_seq=25668 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997693 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115914 bytes_read=2928710 bytes_retransmit=9 bytes_invalid=0 send_seq=15916 receive_seq=15916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38269 bytes_read=1564799 bytes_retransmit=9 bytes_invalid=0 send_seq=6319 receive_seq=6319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38755 bytes_read=116703 bytes_retransmit=9 bytes_invalid=0 send_seq=6306 receive_seq=6306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92847 bytes_read=2408786 bytes_retransmit=0 bytes_invalid=0 send_seq=10865 receive_seq=10865 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998656 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.7 th2: temp=60.3 th3: temp=58.0 sysload=0.16 cputime=449.110 memavail=7395064 print_time=6154.988 buffer_time=2.286 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6131.1: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27294872 bytes_read=4332717 bytes_retransmit=9 bytes_invalid=0 send_seq=518294 receive_seq=518294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=8685 freq=400015903 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38008 bytes_read=119045 bytes_retransmit=0 bytes_invalid=0 send_seq=6306 receive_seq=6306 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999233 adj=49997263 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=184960 bytes_read=5846417 bytes_retransmit=9 bytes_invalid=0 send_seq=25679 receive_seq=25679 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000239 adj=63997774 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115920 bytes_read=2928838 bytes_retransmit=9 bytes_invalid=0 send_seq=15917 receive_seq=15917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38275 bytes_read=1565093 bytes_retransmit=9 bytes_invalid=0 send_seq=6320 receive_seq=6320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38761 bytes_read=116718 bytes_retransmit=9 bytes_invalid=0 send_seq=6307 receive_seq=6307 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92853 bytes_read=2409139 bytes_retransmit=0 bytes_invalid=0 send_seq=10866 receive_seq=10866 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998666 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.8 th2: temp=60.2 th3: temp=57.9 sysload=0.16 cputime=449.225 memavail=7395068 print_time=6155.875 buffer_time=2.169 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 47 Hz
Stats 6132.1: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27303334 bytes_read=4333798 bytes_retransmit=9 bytes_invalid=0 send_seq=518445 receive_seq=518445 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=46 upcoming_bytes=9852 freq=400015888 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38014 bytes_read=119061 bytes_retransmit=0 bytes_invalid=0 send_seq=6307 receive_seq=6307 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999232 adj=49997237 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=185036 bytes_read=5849532 bytes_retransmit=9 bytes_invalid=0 send_seq=25690 receive_seq=25690 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997766 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115926 bytes_read=2928952 bytes_retransmit=9 bytes_invalid=0 send_seq=15918 receive_seq=15918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38281 bytes_read=1565327 bytes_retransmit=9 bytes_invalid=0 send_seq=6321 receive_seq=6321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38767 bytes_read=116744 bytes_retransmit=9 bytes_invalid=0 send_seq=6308 receive_seq=6308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92859 bytes_read=2409484 bytes_retransmit=0 bytes_invalid=0 send_seq=10867 receive_seq=10867 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998670 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.6 th2: temp=60.2 th3: temp=57.9 sysload=0.16 cputime=449.330 memavail=7395068 print_time=6156.803 buffer_time=2.097 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 48 Hz
Testing frequency 49 Hz
Stats 6133.1: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27313131 bytes_read=4335012 bytes_retransmit=9 bytes_invalid=0 send_seq=518620 receive_seq=518620 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=11659 freq=400015878 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38020 bytes_read=119090 bytes_retransmit=0 bytes_invalid=0 send_seq=6308 receive_seq=6308 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999232 adj=49997253 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=185112 bytes_read=5852633 bytes_retransmit=9 bytes_invalid=0 send_seq=25701 receive_seq=25701 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997751 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115932 bytes_read=2929066 bytes_retransmit=9 bytes_invalid=0 send_seq=15919 receive_seq=15919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38287 bytes_read=1565561 bytes_retransmit=9 bytes_invalid=0 send_seq=6322 receive_seq=6322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38773 bytes_read=116759 bytes_retransmit=9 bytes_invalid=0 send_seq=6309 receive_seq=6309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92865 bytes_read=2409829 bytes_retransmit=0 bytes_invalid=0 send_seq=10868 receive_seq=10868 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998682 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.3 th2: temp=60.4 th3: temp=57.9 sysload=0.16 cputime=449.456 memavail=7395068 print_time=6158.005 buffer_time=2.295 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6134.1: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27323155 bytes_read=4336212 bytes_retransmit=9 bytes_invalid=0 send_seq=518798 receive_seq=518798 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=9519 freq=400015867 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38026 bytes_read=119106 bytes_retransmit=0 bytes_invalid=0 send_seq=6309 receive_seq=6309 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999231 adj=49997262 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=185188 bytes_read=5855691 bytes_retransmit=9 bytes_invalid=0 send_seq=25712 receive_seq=25712 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997714 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115938 bytes_read=2929180 bytes_retransmit=9 bytes_invalid=0 send_seq=15920 receive_seq=15920 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38293 bytes_read=1565870 bytes_retransmit=9 bytes_invalid=0 send_seq=6323 receive_seq=6323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38779 bytes_read=116774 bytes_retransmit=9 bytes_invalid=0 send_seq=6310 receive_seq=6310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92871 bytes_read=2410174 bytes_retransmit=0 bytes_invalid=0 send_seq=10869 receive_seq=10869 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998690 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.7 th2: temp=60.3 th3: temp=57.9 sysload=0.16 cputime=449.578 memavail=7395428 print_time=6158.904 buffer_time=2.194 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 50 Hz
Stats 6135.1: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27331925 bytes_read=4337297 bytes_retransmit=9 bytes_invalid=0 send_seq=518953 receive_seq=518953 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=10675 freq=400015869 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38032 bytes_read=119122 bytes_retransmit=0 bytes_invalid=0 send_seq=6310 receive_seq=6310 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999232 adj=49997271 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=185264 bytes_read=5858750 bytes_retransmit=9 bytes_invalid=0 send_seq=25723 receive_seq=25723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997697 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115944 bytes_read=2929280 bytes_retransmit=9 bytes_invalid=0 send_seq=15921 receive_seq=15921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997544 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38299 bytes_read=1566104 bytes_retransmit=9 bytes_invalid=0 send_seq=6324 receive_seq=6324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997677 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38785 bytes_read=116789 bytes_retransmit=9 bytes_invalid=0 send_seq=6311 receive_seq=6311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92877 bytes_read=2410519 bytes_retransmit=0 bytes_invalid=0 send_seq=10870 receive_seq=10870 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998704 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.6 th2: temp=60.2 th3: temp=57.9 sysload=0.14 cputime=449.688 memavail=7395204 print_time=6159.812 buffer_time=2.101 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 51 Hz
Testing frequency 52 Hz
Stats 6136.1: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27342086 bytes_read=4338526 bytes_retransmit=9 bytes_invalid=0 send_seq=519131 receive_seq=519131 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=8451 freq=400015860 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38038 bytes_read=119138 bytes_retransmit=0 bytes_invalid=0 send_seq=6311 receive_seq=6311 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999233 adj=49997270 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=185340 bytes_read=5861839 bytes_retransmit=9 bytes_invalid=0 send_seq=25734 receive_seq=25734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997656 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115950 bytes_read=2929394 bytes_retransmit=9 bytes_invalid=0 send_seq=15922 receive_seq=15922 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38305 bytes_read=1566338 bytes_retransmit=9 bytes_invalid=0 send_seq=6325 receive_seq=6325 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38791 bytes_read=116804 bytes_retransmit=9 bytes_invalid=0 send_seq=6312 receive_seq=6312 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92883 bytes_read=2410864 bytes_retransmit=0 bytes_invalid=0 send_seq=10871 receive_seq=10871 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998690 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.8 th2: temp=60.4 th3: temp=57.9 sysload=0.14 cputime=449.811 memavail=7395208 print_time=6160.703 buffer_time=1.992 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6137.1: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27352586 bytes_read=4339777 bytes_retransmit=9 bytes_invalid=0 send_seq=519316 receive_seq=519316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=10123 freq=400015855 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38044 bytes_read=119154 bytes_retransmit=0 bytes_invalid=0 send_seq=6312 receive_seq=6312 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999233 adj=49997302 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=185416 bytes_read=5864898 bytes_retransmit=9 bytes_invalid=0 send_seq=25745 receive_seq=25745 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997713 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115956 bytes_read=2929522 bytes_retransmit=9 bytes_invalid=0 send_seq=15923 receive_seq=15923 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38311 bytes_read=1566632 bytes_retransmit=9 bytes_invalid=0 send_seq=6326 receive_seq=6326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38797 bytes_read=116830 bytes_retransmit=9 bytes_invalid=0 send_seq=6313 receive_seq=6313 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92889 bytes_read=2411209 bytes_retransmit=0 bytes_invalid=0 send_seq=10872 receive_seq=10872 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998691 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.6 th2: temp=60.3 th3: temp=58.0 sysload=0.14 cputime=449.938 memavail=7395208 print_time=6161.911 buffer_time=2.199 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 53 Hz
Stats 6138.1: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27361447 bytes_read=4340877 bytes_retransmit=9 bytes_invalid=0 send_seq=519474 receive_seq=519474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=11464 freq=400015863 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38050 bytes_read=119183 bytes_retransmit=0 bytes_invalid=0 send_seq=6313 receive_seq=6313 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999241 adj=49997293 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=185492 bytes_read=5868030 bytes_retransmit=9 bytes_invalid=0 send_seq=25756 receive_seq=25756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997689 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115962 bytes_read=2929622 bytes_retransmit=9 bytes_invalid=0 send_seq=15924 receive_seq=15924 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38317 bytes_read=1566866 bytes_retransmit=9 bytes_invalid=0 send_seq=6327 receive_seq=6327 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997669 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38803 bytes_read=116845 bytes_retransmit=9 bytes_invalid=0 send_seq=6314 receive_seq=6314 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92895 bytes_read=2411554 bytes_retransmit=0 bytes_invalid=0 send_seq=10873 receive_seq=10873 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998681 coil_temp=16.9 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.6 th2: temp=60.3 th3: temp=57.8 sysload=0.14 cputime=450.051 memavail=7394968 print_time=6162.824 buffer_time=2.111 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 54 Hz
Stats 6139.1: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27372145 bytes_read=4342146 bytes_retransmit=9 bytes_invalid=0 send_seq=519660 receive_seq=519660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=9079 freq=400015852 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38056 bytes_read=119199 bytes_retransmit=0 bytes_invalid=0 send_seq=6314 receive_seq=6314 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997366 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=185568 bytes_read=5871115 bytes_retransmit=9 bytes_invalid=0 send_seq=25767 receive_seq=25767 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997664 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115968 bytes_read=2929736 bytes_retransmit=9 bytes_invalid=0 send_seq=15925 receive_seq=15925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997530 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=38323 bytes_read=1567115 bytes_retransmit=9 bytes_invalid=0 send_seq=6328 receive_seq=6328 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38809 bytes_read=116860 bytes_retransmit=9 bytes_invalid=0 send_seq=6315 receive_seq=6315 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92901 bytes_read=2411899 bytes_retransmit=0 bytes_invalid=0 send_seq=10874 receive_seq=10874 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998668 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.7 th1: temp=54.7 th2: temp=60.4 th3: temp=57.8 sysload=0.14 cputime=450.167 memavail=7394968 print_time=6163.721 buffer_time=2.008 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 55 Hz
Stats 6140.1: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27382924 bytes_read=4343401 bytes_retransmit=9 bytes_invalid=0 send_seq=519849 receive_seq=519849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=10628 freq=400015853 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38062 bytes_read=119215 bytes_retransmit=0 bytes_invalid=0 send_seq=6315 receive_seq=6315 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997357 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=185644 bytes_read=5874172 bytes_retransmit=9 bytes_invalid=0 send_seq=25778 receive_seq=25778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997682 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115974 bytes_read=2929850 bytes_retransmit=9 bytes_invalid=0 send_seq=15926 receive_seq=15926 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997556 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=38329 bytes_read=1567409 bytes_retransmit=9 bytes_invalid=0 send_seq=6329 receive_seq=6329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38815 bytes_read=116875 bytes_retransmit=9 bytes_invalid=0 send_seq=6316 receive_seq=6316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92907 bytes_read=2412254 bytes_retransmit=0 bytes_invalid=0 send_seq=10875 receive_seq=10875 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998672 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.6 th1: temp=54.6 th2: temp=60.4 th3: temp=58.1 sysload=0.21 cputime=450.295 memavail=7394968 print_time=6164.940 buffer_time=2.227 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 56 Hz
Stats 6141.1: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27392100 bytes_read=4344530 bytes_retransmit=9 bytes_invalid=0 send_seq=520014 receive_seq=520014 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=11884 freq=400015851 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38068 bytes_read=119231 bytes_retransmit=0 bytes_invalid=0 send_seq=6316 receive_seq=6316 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997320 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=185720 bytes_read=5877228 bytes_retransmit=9 bytes_invalid=0 send_seq=25789 receive_seq=25789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997662 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=115980 bytes_read=2929950 bytes_retransmit=9 bytes_invalid=0 send_seq=15927 receive_seq=15927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997534 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=38335 bytes_read=1567643 bytes_retransmit=9 bytes_invalid=0 send_seq=6330 receive_seq=6330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38821 bytes_read=116890 bytes_retransmit=9 bytes_invalid=0 send_seq=6317 receive_seq=6317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92913 bytes_read=2412610 bytes_retransmit=0 bytes_invalid=0 send_seq=10876 receive_seq=10876 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998664 coil_temp=16.9 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.6 th2: temp=60.3 th3: temp=57.9 sysload=0.21 cputime=450.408 memavail=7394984 print_time=6165.817 buffer_time=2.104 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 57 Hz
Stats 6142.1: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27402815 bytes_read=4345810 bytes_retransmit=9 bytes_invalid=0 send_seq=520200 receive_seq=520199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=20 upcoming_bytes=9906 freq=400015888 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38074 bytes_read=119247 bytes_retransmit=0 bytes_invalid=0 send_seq=6317 receive_seq=6317 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997315 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=185796 bytes_read=5880312 bytes_retransmit=9 bytes_invalid=0 send_seq=25800 receive_seq=25800 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997656 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115986 bytes_read=2930078 bytes_retransmit=9 bytes_invalid=0 send_seq=15928 receive_seq=15928 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=38341 bytes_read=1567877 bytes_retransmit=9 bytes_invalid=0 send_seq=6331 receive_seq=6331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38827 bytes_read=116916 bytes_retransmit=9 bytes_invalid=0 send_seq=6318 receive_seq=6318 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92919 bytes_read=2412966 bytes_retransmit=0 bytes_invalid=0 send_seq=10877 receive_seq=10877 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998660 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.5 th2: temp=60.3 th3: temp=57.9 sysload=0.21 cputime=450.527 memavail=7394984 print_time=6166.744 buffer_time=2.029 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 58 Hz
Testing frequency 59 Hz
Stats 6143.1: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27414032 bytes_read=4347105 bytes_retransmit=9 bytes_invalid=0 send_seq=520396 receive_seq=520396 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=11436 freq=400015884 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38080 bytes_read=119276 bytes_retransmit=0 bytes_invalid=0 send_seq=6318 receive_seq=6318 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997243 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=185872 bytes_read=5883386 bytes_retransmit=9 bytes_invalid=0 send_seq=25811 receive_seq=25811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997548 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115992 bytes_read=2930192 bytes_retransmit=9 bytes_invalid=0 send_seq=15929 receive_seq=15929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997568 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=38347 bytes_read=1568171 bytes_retransmit=9 bytes_invalid=0 send_seq=6332 receive_seq=6332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997603 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38833 bytes_read=116931 bytes_retransmit=9 bytes_invalid=0 send_seq=6319 receive_seq=6319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92925 bytes_read=2413322 bytes_retransmit=0 bytes_invalid=0 send_seq=10878 receive_seq=10878 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998621 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.7 th2: temp=60.3 th3: temp=57.8 sysload=0.21 cputime=450.662 memavail=7394984 print_time=6167.957 buffer_time=2.241 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 6144.1: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27423494 bytes_read=4348250 bytes_retransmit=9 bytes_invalid=0 send_seq=520563 receive_seq=520563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=12528 freq=400015871 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38086 bytes_read=119292 bytes_retransmit=0 bytes_invalid=0 send_seq=6319 receive_seq=6319 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997254 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=185941 bytes_read=5886422 bytes_retransmit=9 bytes_invalid=0 send_seq=25821 receive_seq=25821 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997567 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=115998 bytes_read=2930292 bytes_retransmit=9 bytes_invalid=0 send_seq=15930 receive_seq=15930 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997556 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38353 bytes_read=1568420 bytes_retransmit=9 bytes_invalid=0 send_seq=6333 receive_seq=6333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997618 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38839 bytes_read=116946 bytes_retransmit=9 bytes_invalid=0 send_seq=6320 receive_seq=6320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92931 bytes_read=2413678 bytes_retransmit=0 bytes_invalid=0 send_seq=10879 receive_seq=10879 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998634 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=55.1 th1: temp=54.7 th2: temp=60.1 th3: temp=57.9 sysload=0.21 cputime=450.775 memavail=7394996 print_time=6168.840 buffer_time=2.123 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 60 Hz
Stats 6145.1: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27434486 bytes_read=4349554 bytes_retransmit=9 bytes_invalid=0 send_seq=520756 receive_seq=520756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=10631 freq=400015862 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38092 bytes_read=119308 bytes_retransmit=0 bytes_invalid=0 send_seq=6320 receive_seq=6320 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997260 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=186017 bytes_read=5889565 bytes_retransmit=9 bytes_invalid=0 send_seq=25832 receive_seq=25832 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997575 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116004 bytes_read=2930406 bytes_retransmit=9 bytes_invalid=0 send_seq=15931 receive_seq=15931 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997567 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38359 bytes_read=1568654 bytes_retransmit=9 bytes_invalid=0 send_seq=6334 receive_seq=6334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997632 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38845 bytes_read=116961 bytes_retransmit=9 bytes_invalid=0 send_seq=6321 receive_seq=6321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92937 bytes_read=2414034 bytes_retransmit=0 bytes_invalid=0 send_seq=10880 receive_seq=10880 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998645 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=55.5 th1: temp=54.8 th2: temp=60.4 th3: temp=57.9 sysload=0.20 cputime=450.898 memavail=7394996 print_time=6169.760 buffer_time=2.042 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 61 Hz
Testing frequency 62 Hz
Stats 6146.1: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27446009 bytes_read=4350864 bytes_retransmit=9 bytes_invalid=0 send_seq=520956 receive_seq=520956 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=12060 freq=400015868 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38098 bytes_read=119324 bytes_retransmit=0 bytes_invalid=0 send_seq=6321 receive_seq=6321 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997273 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=186093 bytes_read=5892621 bytes_retransmit=9 bytes_invalid=0 send_seq=25843 receive_seq=25843 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997585 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116010 bytes_read=2930520 bytes_retransmit=9 bytes_invalid=0 send_seq=15932 receive_seq=15932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997568 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38365 bytes_read=1568948 bytes_retransmit=9 bytes_invalid=0 send_seq=6335 receive_seq=6335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38851 bytes_read=116976 bytes_retransmit=9 bytes_invalid=0 send_seq=6322 receive_seq=6322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92943 bytes_read=2414374 bytes_retransmit=0 bytes_invalid=0 send_seq=10881 receive_seq=10881 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998653 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=55.5 th1: temp=54.6 th2: temp=60.1 th3: temp=57.9 sysload=0.20 cputime=451.034 memavail=7394996 print_time=6170.965 buffer_time=2.247 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6147.1: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27455772 bytes_read=4352045 bytes_retransmit=9 bytes_invalid=0 send_seq=521127 receive_seq=521127 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=13257 freq=400015886 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38104 bytes_read=119340 bytes_retransmit=0 bytes_invalid=0 send_seq=6322 receive_seq=6322 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997251 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=186169 bytes_read=5895678 bytes_retransmit=9 bytes_invalid=0 send_seq=25854 receive_seq=25854 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997582 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116016 bytes_read=2930634 bytes_retransmit=9 bytes_invalid=0 send_seq=15933 receive_seq=15933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997533 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38371 bytes_read=1569182 bytes_retransmit=9 bytes_invalid=0 send_seq=6336 receive_seq=6336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997634 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38857 bytes_read=117002 bytes_retransmit=9 bytes_invalid=0 send_seq=6323 receive_seq=6323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92949 bytes_read=2414730 bytes_retransmit=0 bytes_invalid=0 send_seq=10882 receive_seq=10882 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998653 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=55.5 th1: temp=54.6 th2: temp=60.3 th3: temp=57.8 sysload=0.20 cputime=451.150 memavail=7394996 print_time=6171.857 buffer_time=2.138 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 63 Hz
Stats 6148.1: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27467006 bytes_read=4353354 bytes_retransmit=9 bytes_invalid=0 send_seq=521321 receive_seq=521321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=35 upcoming_bytes=11423 freq=400015889 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38110 bytes_read=119356 bytes_retransmit=0 bytes_invalid=0 send_seq=6323 receive_seq=6323 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997211 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=186245 bytes_read=5898781 bytes_retransmit=9 bytes_invalid=0 send_seq=25865 receive_seq=25865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997531 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116022 bytes_read=2930748 bytes_retransmit=9 bytes_invalid=0 send_seq=15934 receive_seq=15934 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38377 bytes_read=1569416 bytes_retransmit=9 bytes_invalid=0 send_seq=6337 receive_seq=6337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997607 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38863 bytes_read=117017 bytes_retransmit=9 bytes_invalid=0 send_seq=6324 receive_seq=6324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92955 bytes_read=2415086 bytes_retransmit=0 bytes_invalid=0 send_seq=10883 receive_seq=10883 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998637 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=55.2 th1: temp=54.8 th2: temp=60.4 th3: temp=57.8 sysload=0.20 cputime=451.276 memavail=7393764 print_time=6172.780 buffer_time=2.061 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 64 Hz
Testing frequency 65 Hz
Stats 6149.1: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27478917 bytes_read=4354694 bytes_retransmit=9 bytes_invalid=0 send_seq=521527 receive_seq=521527 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=12852 freq=400015884 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38116 bytes_read=119385 bytes_retransmit=0 bytes_invalid=0 send_seq=6324 receive_seq=6324 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997216 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=186321 bytes_read=5901837 bytes_retransmit=9 bytes_invalid=0 send_seq=25876 receive_seq=25876 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997543 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116028 bytes_read=2930862 bytes_retransmit=9 bytes_invalid=0 send_seq=15935 receive_seq=15935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997488 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38383 bytes_read=1569725 bytes_retransmit=9 bytes_invalid=0 send_seq=6338 receive_seq=6338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997602 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38869 bytes_read=117032 bytes_retransmit=9 bytes_invalid=0 send_seq=6325 receive_seq=6325 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92961 bytes_read=2415442 bytes_retransmit=0 bytes_invalid=0 send_seq=10884 receive_seq=10884 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998641 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=55.6 th1: temp=54.5 th2: temp=60.3 th3: temp=57.9 sysload=0.20 cputime=451.414 memavail=7393776 print_time=6173.983 buffer_time=2.262 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6150.1: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27489014 bytes_read=4355894 bytes_retransmit=9 bytes_invalid=0 send_seq=521705 receive_seq=521705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=13715 freq=400015872 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38122 bytes_read=119401 bytes_retransmit=0 bytes_invalid=0 send_seq=6325 receive_seq=6325 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997238 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=186397 bytes_read=5904893 bytes_retransmit=9 bytes_invalid=0 send_seq=25887 receive_seq=25887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997697 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116034 bytes_read=2930961 bytes_retransmit=9 bytes_invalid=0 send_seq=15936 receive_seq=15936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997499 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38389 bytes_read=1569951 bytes_retransmit=9 bytes_invalid=0 send_seq=6339 receive_seq=6339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38875 bytes_read=117047 bytes_retransmit=9 bytes_invalid=0 send_seq=6326 receive_seq=6326 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92967 bytes_read=2415798 bytes_retransmit=0 bytes_invalid=0 send_seq=10885 receive_seq=10885 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998648 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=55.3 th1: temp=54.7 th2: temp=60.3 th3: temp=57.9 sysload=0.18 cputime=451.530 memavail=7393776 print_time=6174.850 buffer_time=2.129 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 66 Hz
Stats 6151.1: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27500484 bytes_read=4357231 bytes_retransmit=9 bytes_invalid=0 send_seq=521905 receive_seq=521905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=12153 freq=400015865 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38128 bytes_read=119417 bytes_retransmit=0 bytes_invalid=0 send_seq=6326 receive_seq=6326 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997248 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=186473 bytes_read=5907961 bytes_retransmit=9 bytes_invalid=0 send_seq=25898 receive_seq=25898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997780 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116040 bytes_read=2931068 bytes_retransmit=9 bytes_invalid=0 send_seq=15937 receive_seq=15937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997513 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38395 bytes_read=1570169 bytes_retransmit=9 bytes_invalid=0 send_seq=6340 receive_seq=6340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38881 bytes_read=117063 bytes_retransmit=9 bytes_invalid=0 send_seq=6327 receive_seq=6327 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92973 bytes_read=2416154 bytes_retransmit=0 bytes_invalid=0 send_seq=10886 receive_seq=10886 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998669 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=55.6 th1: temp=54.8 th2: temp=60.3 th3: temp=57.9 sysload=0.18 cputime=451.664 memavail=7395140 print_time=6175.794 buffer_time=2.073 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 67 Hz
Testing frequency 68 Hz
Stats 6152.1: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27512746 bytes_read=4358620 bytes_retransmit=9 bytes_invalid=0 send_seq=522118 receive_seq=522118 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=13707 freq=400015857 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38134 bytes_read=119433 bytes_retransmit=0 bytes_invalid=0 send_seq=6327 receive_seq=6327 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999235 adj=49997257 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=186549 bytes_read=5910999 bytes_retransmit=9 bytes_invalid=0 send_seq=25909 receive_seq=25909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997791 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=116046 bytes_read=2931188 bytes_retransmit=9 bytes_invalid=0 send_seq=15938 receive_seq=15938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997527 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38401 bytes_read=1570443 bytes_retransmit=9 bytes_invalid=0 send_seq=6341 receive_seq=6341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38887 bytes_read=117090 bytes_retransmit=9 bytes_invalid=0 send_seq=6328 receive_seq=6328 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92979 bytes_read=2416510 bytes_retransmit=0 bytes_invalid=0 send_seq=10887 receive_seq=10887 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998677 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.5 th2: temp=60.4 th3: temp=57.9 sysload=0.18 cputime=451.804 memavail=7396760 print_time=6176.997 buffer_time=2.275 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6153.1: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27523006 bytes_read=4359840 bytes_retransmit=9 bytes_invalid=0 send_seq=522300 receive_seq=522300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=14522 freq=400015852 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38140 bytes_read=119449 bytes_retransmit=0 bytes_invalid=0 send_seq=6328 receive_seq=6328 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49997262 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=186625 bytes_read=5914114 bytes_retransmit=9 bytes_invalid=0 send_seq=25920 receive_seq=25920 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997748 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=116052 bytes_read=2931281 bytes_retransmit=9 bytes_invalid=0 send_seq=15939 receive_seq=15939 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38407 bytes_read=1570661 bytes_retransmit=9 bytes_invalid=0 send_seq=6342 receive_seq=6342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38893 bytes_read=117106 bytes_retransmit=9 bytes_invalid=0 send_seq=6329 receive_seq=6329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92985 bytes_read=2416866 bytes_retransmit=0 bytes_invalid=0 send_seq=10888 receive_seq=10888 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998677 coil_temp=16.9 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.7 th2: temp=60.3 th3: temp=57.9 sysload=0.18 cputime=451.923 memavail=7396760 print_time=6177.876 buffer_time=2.154 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 69 Hz
Stats 6154.1: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27534958 bytes_read=4361235 bytes_retransmit=9 bytes_invalid=0 send_seq=522509 receive_seq=522509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=12947 freq=400015865 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38152 bytes_read=119494 bytes_retransmit=0 bytes_invalid=0 send_seq=6330 receive_seq=6330 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997256 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=186707 bytes_read=5917195 bytes_retransmit=9 bytes_invalid=0 send_seq=25932 receive_seq=25932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997720 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=116064 bytes_read=2931402 bytes_retransmit=9 bytes_invalid=0 send_seq=15941 receive_seq=15941 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997558 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=38419 bytes_read=1570908 bytes_retransmit=9 bytes_invalid=0 send_seq=6344 receive_seq=6344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38905 bytes_read=117138 bytes_retransmit=9 bytes_invalid=0 send_seq=6331 receive_seq=6331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999449 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=92997 bytes_read=2417238 bytes_retransmit=0 bytes_invalid=0 send_seq=10890 receive_seq=10890 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998679 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.8 th2: temp=60.4 th3: temp=58.0 sysload=0.18 cputime=452.051 memavail=7396760 print_time=6178.802 buffer_time=2.079 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 70 Hz
Testing frequency 71 Hz
Stats 6155.1: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27547542 bytes_read=4362655 bytes_retransmit=9 bytes_invalid=0 send_seq=522731 receive_seq=522731 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=14567 freq=400015905 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38158 bytes_read=119510 bytes_retransmit=0 bytes_invalid=0 send_seq=6331 receive_seq=6331 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997256 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=186783 bytes_read=5920254 bytes_retransmit=9 bytes_invalid=0 send_seq=25943 receive_seq=25943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997706 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=116070 bytes_read=2931516 bytes_retransmit=9 bytes_invalid=0 send_seq=15942 receive_seq=15942 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=38425 bytes_read=1571182 bytes_retransmit=9 bytes_invalid=0 send_seq=6345 receive_seq=6345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38911 bytes_read=117154 bytes_retransmit=9 bytes_invalid=0 send_seq=6332 receive_seq=6332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93003 bytes_read=2417594 bytes_retransmit=0 bytes_invalid=0 send_seq=10891 receive_seq=10891 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998663 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=55.6 th1: temp=54.8 th2: temp=60.1 th3: temp=58.0 sysload=0.16 cputime=452.191 memavail=7396760 print_time=6180.008 buffer_time=2.285 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6156.1: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27558238 bytes_read=4363890 bytes_retransmit=9 bytes_invalid=0 send_seq=522917 receive_seq=522916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=15178 freq=400015906 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38164 bytes_read=119526 bytes_retransmit=0 bytes_invalid=0 send_seq=6332 receive_seq=6332 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997205 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=186852 bytes_read=5923289 bytes_retransmit=9 bytes_invalid=0 send_seq=25953 receive_seq=25953 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997612 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=116076 bytes_read=2931616 bytes_retransmit=9 bytes_invalid=0 send_seq=15943 receive_seq=15943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997455 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=38431 bytes_read=1571416 bytes_retransmit=9 bytes_invalid=0 send_seq=6346 receive_seq=6346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997584 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38917 bytes_read=117170 bytes_retransmit=9 bytes_invalid=0 send_seq=6333 receive_seq=6333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999427 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93009 bytes_read=2417950 bytes_retransmit=0 bytes_invalid=0 send_seq=10892 receive_seq=10892 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998637 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.7 th2: temp=60.4 th3: temp=57.8 sysload=0.16 cputime=452.309 memavail=7396760 print_time=6180.892 buffer_time=2.169 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 72 Hz
Stats 6157.1: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27570459 bytes_read=4365315 bytes_retransmit=9 bytes_invalid=0 send_seq=523130 receive_seq=523130 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=13728 freq=400015907 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38170 bytes_read=119542 bytes_retransmit=0 bytes_invalid=0 send_seq=6333 receive_seq=6333 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997200 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=186928 bytes_read=5926375 bytes_retransmit=9 bytes_invalid=0 send_seq=25964 receive_seq=25964 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997680 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116082 bytes_read=2931758 bytes_retransmit=9 bytes_invalid=0 send_seq=15944 receive_seq=15944 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997448 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=38437 bytes_read=1571650 bytes_retransmit=9 bytes_invalid=0 send_seq=6347 receive_seq=6347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997592 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38923 bytes_read=117197 bytes_retransmit=9 bytes_invalid=0 send_seq=6334 receive_seq=6334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93015 bytes_read=2418306 bytes_retransmit=0 bytes_invalid=0 send_seq=10893 receive_seq=10893 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998644 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=55.5 th1: temp=54.8 th2: temp=60.2 th3: temp=57.9 sysload=0.16 cputime=452.437 memavail=7396284 print_time=6181.814 buffer_time=2.090 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 73 Hz
Testing frequency 74 Hz
Stats 6158.1: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27583311 bytes_read=4366740 bytes_retransmit=9 bytes_invalid=0 send_seq=523353 receive_seq=523353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=15903 freq=400015939 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38176 bytes_read=119558 bytes_retransmit=0 bytes_invalid=0 send_seq=6334 receive_seq=6334 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997203 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=187004 bytes_read=5929450 bytes_retransmit=9 bytes_invalid=0 send_seq=25975 receive_seq=25975 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997658 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116088 bytes_read=2931858 bytes_retransmit=9 bytes_invalid=0 send_seq=15945 receive_seq=15945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997450 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=38443 bytes_read=1571944 bytes_retransmit=9 bytes_invalid=0 send_seq=6348 receive_seq=6348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997601 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38929 bytes_read=117213 bytes_retransmit=9 bytes_invalid=0 send_seq=6335 receive_seq=6335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93021 bytes_read=2418662 bytes_retransmit=0 bytes_invalid=0 send_seq=10894 receive_seq=10894 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998642 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=55.5 th1: temp=54.7 th2: temp=60.3 th3: temp=57.9 sysload=0.16 cputime=452.581 memavail=7395292 print_time=6183.032 buffer_time=2.308 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6159.1: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27594300 bytes_read=4367995 bytes_retransmit=9 bytes_invalid=0 send_seq=523542 receive_seq=523542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=15977 freq=400015947 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38182 bytes_read=119587 bytes_retransmit=0 bytes_invalid=0 send_seq=6335 receive_seq=6335 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997174 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=187080 bytes_read=5932507 bytes_retransmit=9 bytes_invalid=0 send_seq=25986 receive_seq=25986 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997580 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116094 bytes_read=2931958 bytes_retransmit=9 bytes_invalid=0 send_seq=15946 receive_seq=15946 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997426 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38449 bytes_read=1572193 bytes_retransmit=9 bytes_invalid=0 send_seq=6349 receive_seq=6349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997574 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38935 bytes_read=117229 bytes_retransmit=9 bytes_invalid=0 send_seq=6336 receive_seq=6336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93027 bytes_read=2419018 bytes_retransmit=0 bytes_invalid=0 send_seq=10895 receive_seq=10895 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998619 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=55.7 th1: temp=54.8 th2: temp=60.2 th3: temp=57.9 sysload=0.16 cputime=452.706 memavail=7395292 print_time=6183.908 buffer_time=2.183 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 75 Hz
Stats 6160.1: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27606789 bytes_read=4369419 bytes_retransmit=9 bytes_invalid=0 send_seq=523759 receive_seq=523759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=14855 freq=400015969 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38188 bytes_read=119603 bytes_retransmit=0 bytes_invalid=0 send_seq=6336 receive_seq=6336 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997185 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=187156 bytes_read=5935594 bytes_retransmit=9 bytes_invalid=0 send_seq=25997 receive_seq=25997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997545 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116100 bytes_read=2932086 bytes_retransmit=9 bytes_invalid=0 send_seq=15947 receive_seq=15947 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997411 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38455 bytes_read=1572427 bytes_retransmit=9 bytes_invalid=0 send_seq=6350 receive_seq=6350 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997580 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38941 bytes_read=117245 bytes_retransmit=9 bytes_invalid=0 send_seq=6337 receive_seq=6337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999421 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93033 bytes_read=2419374 bytes_retransmit=0 bytes_invalid=0 send_seq=10896 receive_seq=10896 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998643 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=55.5 th1: temp=54.7 th2: temp=60.2 th3: temp=57.9 sysload=0.15 cputime=452.838 memavail=7395292 print_time=6184.833 buffer_time=2.108 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 76 Hz
Testing frequency 77 Hz
Stats 6161.1: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27620026 bytes_read=4370859 bytes_retransmit=9 bytes_invalid=0 send_seq=523985 receive_seq=523985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=16584 freq=400015961 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38194 bytes_read=119619 bytes_retransmit=0 bytes_invalid=0 send_seq=6337 receive_seq=6337 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997159 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=187232 bytes_read=5938711 bytes_retransmit=9 bytes_invalid=0 send_seq=26008 receive_seq=26008 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997503 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116106 bytes_read=2932186 bytes_retransmit=9 bytes_invalid=0 send_seq=15948 receive_seq=15948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997389 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38461 bytes_read=1572721 bytes_retransmit=9 bytes_invalid=0 send_seq=6351 receive_seq=6351 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997561 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38947 bytes_read=117261 bytes_retransmit=9 bytes_invalid=0 send_seq=6338 receive_seq=6338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999415 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93039 bytes_read=2419730 bytes_retransmit=0 bytes_invalid=0 send_seq=10897 receive_seq=10897 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998622 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=55.5 th1: temp=54.7 th2: temp=60.1 th3: temp=57.9 sysload=0.15 cputime=452.985 memavail=7395292 print_time=6186.035 buffer_time=2.307 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 6162.1: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27631360 bytes_read=4372167 bytes_retransmit=9 bytes_invalid=0 send_seq=524182 receive_seq=524182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=16476 freq=400015968 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38200 bytes_read=119635 bytes_retransmit=0 bytes_invalid=0 send_seq=6338 receive_seq=6338 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997194 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=187308 bytes_read=5941768 bytes_retransmit=9 bytes_invalid=0 send_seq=26019 receive_seq=26019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997543 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116112 bytes_read=2932286 bytes_retransmit=9 bytes_invalid=0 send_seq=15949 receive_seq=15949 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997465 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38467 bytes_read=1572955 bytes_retransmit=9 bytes_invalid=0 send_seq=6352 receive_seq=6352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38953 bytes_read=117288 bytes_retransmit=9 bytes_invalid=0 send_seq=6339 receive_seq=6339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93045 bytes_read=2420086 bytes_retransmit=0 bytes_invalid=0 send_seq=10898 receive_seq=10898 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998646 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=55.6 th1: temp=54.8 th2: temp=60.4 th3: temp=57.9 sysload=0.15 cputime=453.186 memavail=7395304 print_time=6186.903 buffer_time=2.174 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 78 Hz
Stats 6163.1: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27644126 bytes_read=4373609 bytes_retransmit=9 bytes_invalid=0 send_seq=524403 receive_seq=524403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=15900 freq=400015976 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38206 bytes_read=119651 bytes_retransmit=0 bytes_invalid=0 send_seq=6339 receive_seq=6339 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997185 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=187377 bytes_read=5944846 bytes_retransmit=9 bytes_invalid=0 send_seq=26029 receive_seq=26029 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997522 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116118 bytes_read=2932428 bytes_retransmit=9 bytes_invalid=0 send_seq=15950 receive_seq=15950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997445 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38473 bytes_read=1573189 bytes_retransmit=9 bytes_invalid=0 send_seq=6353 receive_seq=6353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38959 bytes_read=117304 bytes_retransmit=9 bytes_invalid=0 send_seq=6340 receive_seq=6340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999425 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93051 bytes_read=2420442 bytes_retransmit=0 bytes_invalid=0 send_seq=10899 receive_seq=10899 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998635 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=55.1 th1: temp=54.8 th2: temp=60.3 th3: temp=57.9 sysload=0.15 cputime=453.314 memavail=7395304 print_time=6187.853 buffer_time=2.124 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 79 Hz
Testing frequency 80 Hz
Stats 6164.1: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27657737 bytes_read=4375069 bytes_retransmit=9 bytes_invalid=0 send_seq=524633 receive_seq=524633 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=13239 freq=400015984 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38212 bytes_read=119680 bytes_retransmit=0 bytes_invalid=0 send_seq=6340 receive_seq=6340 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997197 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=187453 bytes_read=5947903 bytes_retransmit=9 bytes_invalid=0 send_seq=26040 receive_seq=26040 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997604 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116124 bytes_read=2932528 bytes_retransmit=9 bytes_invalid=0 send_seq=15951 receive_seq=15951 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997434 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38479 bytes_read=1573498 bytes_retransmit=9 bytes_invalid=0 send_seq=6354 receive_seq=6354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38965 bytes_read=117320 bytes_retransmit=9 bytes_invalid=0 send_seq=6341 receive_seq=6341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999433 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93057 bytes_read=2420798 bytes_retransmit=0 bytes_invalid=0 send_seq=10900 receive_seq=10900 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998645 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=55.7 th1: temp=54.8 th2: temp=60.1 th3: temp=57.8 sysload=0.15 cputime=453.461 memavail=7394812 print_time=6188.716 buffer_time=1.987 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 6165.1: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27669218 bytes_read=4376379 bytes_retransmit=9 bytes_invalid=0 send_seq=524833 receive_seq=524833 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=16843 freq=400015989 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38218 bytes_read=119696 bytes_retransmit=0 bytes_invalid=0 send_seq=6341 receive_seq=6341 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997201 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=187529 bytes_read=5950960 bytes_retransmit=9 bytes_invalid=0 send_seq=26051 receive_seq=26051 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997567 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116130 bytes_read=2932628 bytes_retransmit=9 bytes_invalid=0 send_seq=15952 receive_seq=15952 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997417 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38485 bytes_read=1573732 bytes_retransmit=9 bytes_invalid=0 send_seq=6355 receive_seq=6355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38971 bytes_read=117336 bytes_retransmit=9 bytes_invalid=0 send_seq=6342 receive_seq=6342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999429 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93063 bytes_read=2421154 bytes_retransmit=0 bytes_invalid=0 send_seq=10901 receive_seq=10901 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998647 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=55.8 th1: temp=54.8 th2: temp=60.3 th3: temp=57.9 sysload=0.14 cputime=453.596 memavail=7394812 print_time=6189.923 buffer_time=2.194 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 81 Hz
Stats 6166.1: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27681983 bytes_read=4377828 bytes_retransmit=9 bytes_invalid=0 send_seq=525055 receive_seq=525055 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=16628 freq=400015994 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38224 bytes_read=119712 bytes_retransmit=0 bytes_invalid=0 send_seq=6342 receive_seq=6342 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997207 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=187605 bytes_read=5954046 bytes_retransmit=9 bytes_invalid=0 send_seq=26062 receive_seq=26062 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997566 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116136 bytes_read=2932756 bytes_retransmit=9 bytes_invalid=0 send_seq=15953 receive_seq=15953 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997431 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38491 bytes_read=1573966 bytes_retransmit=9 bytes_invalid=0 send_seq=6356 receive_seq=6356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38977 bytes_read=117352 bytes_retransmit=9 bytes_invalid=0 send_seq=6343 receive_seq=6343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999429 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93069 bytes_read=2421510 bytes_retransmit=0 bytes_invalid=0 send_seq=10902 receive_seq=10902 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998646 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=55.6 th1: temp=54.9 th2: temp=60.4 th3: temp=57.8 sysload=0.14 cputime=453.728 memavail=7394812 print_time=6190.859 buffer_time=2.129 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 82 Hz
Testing frequency 83 Hz
Stats 6167.1: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27695906 bytes_read=4379354 bytes_retransmit=9 bytes_invalid=0 send_seq=525295 receive_seq=525295 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=26 upcoming_bytes=13847 freq=400015975 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38230 bytes_read=119728 bytes_retransmit=0 bytes_invalid=0 send_seq=6343 receive_seq=6343 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997211 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=187681 bytes_read=5957162 bytes_retransmit=9 bytes_invalid=0 send_seq=26073 receive_seq=26073 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997572 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116142 bytes_read=2932856 bytes_retransmit=9 bytes_invalid=0 send_seq=15954 receive_seq=15954 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997423 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38497 bytes_read=1574260 bytes_retransmit=9 bytes_invalid=0 send_seq=6357 receive_seq=6357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997606 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38983 bytes_read=117379 bytes_retransmit=9 bytes_invalid=0 send_seq=6344 receive_seq=6344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93075 bytes_read=2421866 bytes_retransmit=0 bytes_invalid=0 send_seq=10903 receive_seq=10903 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998636 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=55.7 th1: temp=54.9 th2: temp=60.4 th3: temp=57.9 sysload=0.14 cputime=453.865 memavail=7394812 print_time=6191.724 buffer_time=1.993 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 84 Hz
Stats 6168.1: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27707903 bytes_read=4380709 bytes_retransmit=9 bytes_invalid=0 send_seq=525504 receive_seq=525504 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=17026 freq=400015979 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38236 bytes_read=119744 bytes_retransmit=0 bytes_invalid=0 send_seq=6344 receive_seq=6344 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997239 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=187757 bytes_read=5960236 bytes_retransmit=9 bytes_invalid=0 send_seq=26084 receive_seq=26084 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997720 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116148 bytes_read=2932970 bytes_retransmit=9 bytes_invalid=0 send_seq=15955 receive_seq=15955 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997462 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38503 bytes_read=1574494 bytes_retransmit=9 bytes_invalid=0 send_seq=6358 receive_seq=6358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38989 bytes_read=117395 bytes_retransmit=9 bytes_invalid=0 send_seq=6345 receive_seq=6345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999433 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93081 bytes_read=2422222 bytes_retransmit=0 bytes_invalid=0 send_seq=10904 receive_seq=10904 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998654 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=55.6 th1: temp=54.6 th2: temp=60.3 th3: temp=58.0 sysload=0.14 cputime=454.015 memavail=7387812 print_time=6192.930 buffer_time=2.198 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6169.1: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27720693 bytes_read=4382143 bytes_retransmit=9 bytes_invalid=0 send_seq=525723 receive_seq=525723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=17160 freq=400015976 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38242 bytes_read=119773 bytes_retransmit=0 bytes_invalid=0 send_seq=6345 receive_seq=6345 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997231 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=187833 bytes_read=5963322 bytes_retransmit=9 bytes_invalid=0 send_seq=26095 receive_seq=26095 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997762 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116154 bytes_read=2933098 bytes_retransmit=9 bytes_invalid=0 send_seq=15956 receive_seq=15956 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997458 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38509 bytes_read=1574743 bytes_retransmit=9 bytes_invalid=0 send_seq=6359 receive_seq=6359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997616 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=38995 bytes_read=117411 bytes_retransmit=9 bytes_invalid=0 send_seq=6346 receive_seq=6346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93087 bytes_read=2422578 bytes_retransmit=0 bytes_invalid=0 send_seq=10905 receive_seq=10905 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998650 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=55.7 th1: temp=54.5 th2: temp=60.3 th3: temp=58.1 sysload=0.14 cputime=454.146 memavail=7394444 print_time=6193.865 buffer_time=2.133 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 85 Hz
Testing frequency 86 Hz
Stats 6170.1: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27734713 bytes_read=4383668 bytes_retransmit=9 bytes_invalid=0 send_seq=525966 receive_seq=525966 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=14503 freq=400015976 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38248 bytes_read=119789 bytes_retransmit=0 bytes_invalid=0 send_seq=6346 receive_seq=6346 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997236 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=187909 bytes_read=5966380 bytes_retransmit=9 bytes_invalid=0 send_seq=26106 receive_seq=26106 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997744 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116160 bytes_read=2933198 bytes_retransmit=9 bytes_invalid=0 send_seq=15957 receive_seq=15957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997466 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38515 bytes_read=1575037 bytes_retransmit=9 bytes_invalid=0 send_seq=6360 receive_seq=6360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997616 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39001 bytes_read=117427 bytes_retransmit=9 bytes_invalid=0 send_seq=6347 receive_seq=6347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93093 bytes_read=2422934 bytes_retransmit=0 bytes_invalid=0 send_seq=10906 receive_seq=10906 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998648 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.8 th2: temp=60.3 th3: temp=57.9 sysload=0.13 cputime=454.279 memavail=7394444 print_time=6194.729 buffer_time=1.995 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 87 Hz
Stats 6171.1: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27746806 bytes_read=4385033 bytes_retransmit=9 bytes_invalid=0 send_seq=526177 receive_seq=526177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=18035 freq=400015964 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38254 bytes_read=119805 bytes_retransmit=0 bytes_invalid=0 send_seq=6347 receive_seq=6347 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997239 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=187985 bytes_read=5969436 bytes_retransmit=9 bytes_invalid=0 send_seq=26117 receive_seq=26117 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997735 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116166 bytes_read=2933298 bytes_retransmit=9 bytes_invalid=0 send_seq=15958 receive_seq=15958 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997470 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38521 bytes_read=1575271 bytes_retransmit=9 bytes_invalid=0 send_seq=6361 receive_seq=6361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997613 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39007 bytes_read=117443 bytes_retransmit=9 bytes_invalid=0 send_seq=6348 receive_seq=6348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93099 bytes_read=2423290 bytes_retransmit=0 bytes_invalid=0 send_seq=10907 receive_seq=10907 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998657 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=55.6 th1: temp=54.4 th2: temp=60.3 th3: temp=58.1 sysload=0.13 cputime=454.418 memavail=7394444 print_time=6195.933 buffer_time=2.199 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6172.1: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27760311 bytes_read=4386533 bytes_retransmit=9 bytes_invalid=0 send_seq=526406 receive_seq=526406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=17924 freq=400015964 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38260 bytes_read=119821 bytes_retransmit=0 bytes_invalid=0 send_seq=6348 receive_seq=6348 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997244 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=188061 bytes_read=5972521 bytes_retransmit=9 bytes_invalid=0 send_seq=26128 receive_seq=26128 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997713 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116172 bytes_read=2933426 bytes_retransmit=9 bytes_invalid=0 send_seq=15959 receive_seq=15959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997502 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38527 bytes_read=1575505 bytes_retransmit=9 bytes_invalid=0 send_seq=6362 receive_seq=6362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39013 bytes_read=117470 bytes_retransmit=9 bytes_invalid=0 send_seq=6349 receive_seq=6349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93105 bytes_read=2423646 bytes_retransmit=0 bytes_invalid=0 send_seq=10908 receive_seq=10908 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998673 coil_temp=16.9 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.8 th2: temp=60.3 th3: temp=58.0 sysload=0.13 cputime=454.548 memavail=7394444 print_time=6196.873 buffer_time=2.139 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 88 Hz
Stats 6173.1: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27774641 bytes_read=4388073 bytes_retransmit=9 bytes_invalid=0 send_seq=526653 receive_seq=526653 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=14805 freq=400015993 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38266 bytes_read=119837 bytes_retransmit=0 bytes_invalid=0 send_seq=6349 receive_seq=6349 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997231 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=188137 bytes_read=5975596 bytes_retransmit=9 bytes_invalid=0 send_seq=26139 receive_seq=26139 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997689 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116178 bytes_read=2933540 bytes_retransmit=9 bytes_invalid=0 send_seq=15960 receive_seq=15960 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997494 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38533 bytes_read=1575799 bytes_retransmit=9 bytes_invalid=0 send_seq=6363 receive_seq=6363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39019 bytes_read=117486 bytes_retransmit=9 bytes_invalid=0 send_seq=6350 receive_seq=6350 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93111 bytes_read=2424002 bytes_retransmit=0 bytes_invalid=0 send_seq=10909 receive_seq=10909 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998672 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=55.6 th1: temp=54.6 th2: temp=60.3 th3: temp=58.0 sysload=0.13 cputime=454.682 memavail=7394456 print_time=6197.742 buffer_time=2.008 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 89 Hz
Testing frequency 90 Hz
Stats 6174.1: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27787275 bytes_read=4389488 bytes_retransmit=9 bytes_invalid=0 send_seq=526874 receive_seq=526874 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=18101 freq=400015980 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38272 bytes_read=119866 bytes_retransmit=0 bytes_invalid=0 send_seq=6350 receive_seq=6350 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997192 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=188213 bytes_read=5978653 bytes_retransmit=9 bytes_invalid=0 send_seq=26150 receive_seq=26150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997599 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116184 bytes_read=2933640 bytes_retransmit=9 bytes_invalid=0 send_seq=15961 receive_seq=15961 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997433 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38539 bytes_read=1576048 bytes_retransmit=9 bytes_invalid=0 send_seq=6364 receive_seq=6364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997576 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39025 bytes_read=117502 bytes_retransmit=9 bytes_invalid=0 send_seq=6351 receive_seq=6351 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93117 bytes_read=2424358 bytes_retransmit=0 bytes_invalid=0 send_seq=10910 receive_seq=10910 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998660 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.9 th2: temp=60.3 th3: temp=57.9 sysload=0.13 cputime=454.828 memavail=7394456 print_time=6198.950 buffer_time=2.215 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6175.1: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27800518 bytes_read=4390972 bytes_retransmit=9 bytes_invalid=0 send_seq=527103 receive_seq=527103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=18207 freq=400015980 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38278 bytes_read=119882 bytes_retransmit=0 bytes_invalid=0 send_seq=6351 receive_seq=6351 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997229 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=188289 bytes_read=5981796 bytes_retransmit=9 bytes_invalid=0 send_seq=26161 receive_seq=26161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997626 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116190 bytes_read=2933768 bytes_retransmit=9 bytes_invalid=0 send_seq=15962 receive_seq=15962 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997491 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38545 bytes_read=1576282 bytes_retransmit=9 bytes_invalid=0 send_seq=6365 receive_seq=6365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997608 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39031 bytes_read=117518 bytes_retransmit=9 bytes_invalid=0 send_seq=6352 receive_seq=6352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93123 bytes_read=2424714 bytes_retransmit=0 bytes_invalid=0 send_seq=10911 receive_seq=10911 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998670 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=55.6 th1: temp=54.6 th2: temp=60.4 th3: temp=57.8 sysload=0.12 cputime=454.960 memavail=7394456 print_time=6199.879 buffer_time=2.143 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 91 Hz
Stats 6176.1: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27815130 bytes_read=4392532 bytes_retransmit=9 bytes_invalid=0 send_seq=527353 receive_seq=527353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=14956 freq=400015969 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38284 bytes_read=119898 bytes_retransmit=0 bytes_invalid=0 send_seq=6352 receive_seq=6352 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997231 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=188365 bytes_read=5984854 bytes_retransmit=9 bytes_invalid=0 send_seq=26172 receive_seq=26172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997605 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116196 bytes_read=2933868 bytes_retransmit=9 bytes_invalid=0 send_seq=15963 receive_seq=15963 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38551 bytes_read=1576576 bytes_retransmit=9 bytes_invalid=0 send_seq=6366 receive_seq=6366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39037 bytes_read=117534 bytes_retransmit=9 bytes_invalid=0 send_seq=6353 receive_seq=6353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93129 bytes_read=2425070 bytes_retransmit=0 bytes_invalid=0 send_seq=10912 receive_seq=10912 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998674 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.9 th2: temp=60.3 th3: temp=57.9 sysload=0.12 cputime=455.093 memavail=7394456 print_time=6200.740 buffer_time=2.005 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 92 Hz
Testing frequency 93 Hz
Stats 6177.1: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27827561 bytes_read=4393948 bytes_retransmit=9 bytes_invalid=0 send_seq=527571 receive_seq=527571 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=18581 freq=400016003 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38290 bytes_read=119914 bytes_retransmit=0 bytes_invalid=0 send_seq=6353 receive_seq=6353 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997247 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=188434 bytes_read=5987889 bytes_retransmit=9 bytes_invalid=0 send_seq=26182 receive_seq=26182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997607 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116202 bytes_read=2933968 bytes_retransmit=9 bytes_invalid=0 send_seq=15964 receive_seq=15964 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997562 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38557 bytes_read=1576810 bytes_retransmit=9 bytes_invalid=0 send_seq=6367 receive_seq=6367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39043 bytes_read=117561 bytes_retransmit=9 bytes_invalid=0 send_seq=6354 receive_seq=6354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93135 bytes_read=2425426 bytes_retransmit=0 bytes_invalid=0 send_seq=10913 receive_seq=10913 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998691 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.9 th2: temp=60.5 th3: temp=57.8 sysload=0.12 cputime=455.240 memavail=7394456 print_time=6201.958 buffer_time=2.222 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6178.1: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27841337 bytes_read=4395482 bytes_retransmit=9 bytes_invalid=0 send_seq=527810 receive_seq=527810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=18704 freq=400015984 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38296 bytes_read=119930 bytes_retransmit=0 bytes_invalid=0 send_seq=6354 receive_seq=6354 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997205 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=188510 bytes_read=5990990 bytes_retransmit=9 bytes_invalid=0 send_seq=26193 receive_seq=26193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997555 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116208 bytes_read=2934110 bytes_retransmit=9 bytes_invalid=0 send_seq=15965 receive_seq=15965 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997472 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38563 bytes_read=1577044 bytes_retransmit=9 bytes_invalid=0 send_seq=6368 receive_seq=6368 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997583 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39049 bytes_read=117577 bytes_retransmit=9 bytes_invalid=0 send_seq=6355 receive_seq=6355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93141 bytes_read=2425782 bytes_retransmit=0 bytes_invalid=0 send_seq=10914 receive_seq=10914 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998646 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=55.7 th1: temp=54.9 th2: temp=60.4 th3: temp=57.9 sysload=0.12 cputime=455.375 memavail=7393996 print_time=6202.889 buffer_time=2.153 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 94 Hz
Stats 6179.1: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27855855 bytes_read=4397042 bytes_retransmit=9 bytes_invalid=0 send_seq=528060 receive_seq=528060 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=15719 freq=400015980 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38302 bytes_read=119959 bytes_retransmit=0 bytes_invalid=0 send_seq=6355 receive_seq=6355 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997230 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=188586 bytes_read=5994051 bytes_retransmit=9 bytes_invalid=0 send_seq=26204 receive_seq=26204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997593 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116214 bytes_read=2934210 bytes_retransmit=9 bytes_invalid=0 send_seq=15966 receive_seq=15966 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997503 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38569 bytes_read=1577353 bytes_retransmit=9 bytes_invalid=0 send_seq=6369 receive_seq=6369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997700 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39055 bytes_read=117593 bytes_retransmit=9 bytes_invalid=0 send_seq=6356 receive_seq=6356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93147 bytes_read=2426138 bytes_retransmit=0 bytes_invalid=0 send_seq=10915 receive_seq=10915 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998667 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=55.5 th1: temp=55.0 th2: temp=60.4 th3: temp=57.9 sysload=0.12 cputime=455.511 memavail=7394000 print_time=6203.760 buffer_time=2.024 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 95 Hz
Testing frequency 96 Hz
Stats 6180.1: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27868623 bytes_read=4398462 bytes_retransmit=9 bytes_invalid=0 send_seq=528282 receive_seq=528282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=19443 freq=400015982 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38308 bytes_read=119975 bytes_retransmit=0 bytes_invalid=0 send_seq=6356 receive_seq=6356 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997226 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=188662 bytes_read=5997107 bytes_retransmit=9 bytes_invalid=0 send_seq=26215 receive_seq=26215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997585 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116220 bytes_read=2934310 bytes_retransmit=9 bytes_invalid=0 send_seq=15967 receive_seq=15967 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38575 bytes_read=1577587 bytes_retransmit=9 bytes_invalid=0 send_seq=6370 receive_seq=6370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39061 bytes_read=117609 bytes_retransmit=9 bytes_invalid=0 send_seq=6357 receive_seq=6357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999436 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93153 bytes_read=2426494 bytes_retransmit=0 bytes_invalid=0 send_seq=10916 receive_seq=10916 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998665 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=55.6 th1: temp=55.1 th2: temp=60.4 th3: temp=57.9 sysload=0.11 cputime=455.662 memavail=7394000 print_time=6204.965 buffer_time=2.228 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6181.1: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27882654 bytes_read=4400021 bytes_retransmit=9 bytes_invalid=0 send_seq=528526 receive_seq=528526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=19507 freq=400015982 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38314 bytes_read=119991 bytes_retransmit=0 bytes_invalid=0 send_seq=6357 receive_seq=6357 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997228 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=188738 bytes_read=6000191 bytes_retransmit=9 bytes_invalid=0 send_seq=26226 receive_seq=26226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997599 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116226 bytes_read=2934438 bytes_retransmit=9 bytes_invalid=0 send_seq=15968 receive_seq=15968 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997491 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38581 bytes_read=1577836 bytes_retransmit=9 bytes_invalid=0 send_seq=6371 receive_seq=6371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39067 bytes_read=117625 bytes_retransmit=9 bytes_invalid=0 send_seq=6358 receive_seq=6358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93159 bytes_read=2426850 bytes_retransmit=0 bytes_invalid=0 send_seq=10917 receive_seq=10917 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998654 coil_temp=17.0 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.8 th2: temp=60.4 th3: temp=57.8 sysload=0.11 cputime=455.795 memavail=7394000 print_time=6205.893 buffer_time=2.155 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 97 Hz
Stats 6182.1: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27897864 bytes_read=4401657 bytes_retransmit=9 bytes_invalid=0 send_seq=528788 receive_seq=528788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=35 upcoming_bytes=16079 freq=400015974 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38320 bytes_read=120007 bytes_retransmit=0 bytes_invalid=0 send_seq=6358 receive_seq=6358 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997242 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=188814 bytes_read=6003247 bytes_retransmit=9 bytes_invalid=0 send_seq=26237 receive_seq=26237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997590 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116232 bytes_read=2934538 bytes_retransmit=9 bytes_invalid=0 send_seq=15969 receive_seq=15969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997488 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38587 bytes_read=1578115 bytes_retransmit=9 bytes_invalid=0 send_seq=6372 receive_seq=6372 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39073 bytes_read=117652 bytes_retransmit=9 bytes_invalid=0 send_seq=6359 receive_seq=6359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999437 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93165 bytes_read=2427206 bytes_retransmit=0 bytes_invalid=0 send_seq=10918 receive_seq=10918 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998679 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=55.5 th1: temp=54.8 th2: temp=60.3 th3: temp=58.0 sysload=0.11 cputime=455.932 memavail=7394148 print_time=6206.768 buffer_time=2.030 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 98 Hz
Testing frequency 99 Hz
Stats 6183.1: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27910791 bytes_read=4403082 bytes_retransmit=9 bytes_invalid=0 send_seq=529011 receive_seq=529011 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=19754 freq=400015967 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38326 bytes_read=120023 bytes_retransmit=0 bytes_invalid=0 send_seq=6359 receive_seq=6359 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997252 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=188890 bytes_read=6006378 bytes_retransmit=9 bytes_invalid=0 send_seq=26248 receive_seq=26248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997618 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116238 bytes_read=2934652 bytes_retransmit=9 bytes_invalid=0 send_seq=15970 receive_seq=15970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997497 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38593 bytes_read=1578349 bytes_retransmit=9 bytes_invalid=0 send_seq=6373 receive_seq=6373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39079 bytes_read=117668 bytes_retransmit=9 bytes_invalid=0 send_seq=6360 receive_seq=6360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999449 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93171 bytes_read=2427562 bytes_retransmit=0 bytes_invalid=0 send_seq=10919 receive_seq=10919 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998676 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=55.7 th1: temp=54.9 th2: temp=60.3 th3: temp=57.9 sysload=0.11 cputime=456.083 memavail=7394260 print_time=6207.970 buffer_time=2.231 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6184.1: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27925040 bytes_read=4404631 bytes_retransmit=9 bytes_invalid=0 send_seq=529254 receive_seq=529254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=19967 freq=400015962 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38332 bytes_read=120052 bytes_retransmit=0 bytes_invalid=0 send_seq=6360 receive_seq=6360 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997270 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=188966 bytes_read=6009463 bytes_retransmit=9 bytes_invalid=0 send_seq=26259 receive_seq=26259 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997761 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116244 bytes_read=2934780 bytes_retransmit=9 bytes_invalid=0 send_seq=15971 receive_seq=15971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=38599 bytes_read=1578613 bytes_retransmit=9 bytes_invalid=0 send_seq=6374 receive_seq=6374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39085 bytes_read=117684 bytes_retransmit=9 bytes_invalid=0 send_seq=6361 receive_seq=6361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93177 bytes_read=2427918 bytes_retransmit=0 bytes_invalid=0 send_seq=10920 receive_seq=10920 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998672 coil_temp=17.0 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=55.8 th1: temp=54.8 th2: temp=60.3 th3: temp=58.1 sysload=0.11 cputime=456.218 memavail=7394288 print_time=6208.902 buffer_time=2.163 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 100 Hz
Stats 6185.1: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27940384 bytes_read=4406256 bytes_retransmit=9 bytes_invalid=0 send_seq=529517 receive_seq=529517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=16276 freq=400015948 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38338 bytes_read=120068 bytes_retransmit=0 bytes_invalid=0 send_seq=6361 receive_seq=6361 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999238 adj=49997267 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=189042 bytes_read=6012521 bytes_retransmit=9 bytes_invalid=0 send_seq=26270 receive_seq=26270 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997791 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116250 bytes_read=2934880 bytes_retransmit=9 bytes_invalid=0 send_seq=15972 receive_seq=15972 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997517 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=38605 bytes_read=1578892 bytes_retransmit=9 bytes_invalid=0 send_seq=6375 receive_seq=6375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39091 bytes_read=117700 bytes_retransmit=9 bytes_invalid=0 send_seq=6362 receive_seq=6362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93183 bytes_read=2428274 bytes_retransmit=0 bytes_invalid=0 send_seq=10921 receive_seq=10921 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998672 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=55.5 th1: temp=54.8 th2: temp=60.4 th3: temp=58.0 sysload=0.18 cputime=456.364 memavail=7387744 print_time=6209.771 buffer_time=2.031 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 101 Hz
Testing frequency 102 Hz
Stats 6186.1: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27953557 bytes_read=4407721 bytes_retransmit=9 bytes_invalid=0 send_seq=529748 receive_seq=529748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=20122 freq=400015947 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38344 bytes_read=120084 bytes_retransmit=0 bytes_invalid=0 send_seq=6362 receive_seq=6362 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999239 adj=49997284 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=189118 bytes_read=6015577 bytes_retransmit=9 bytes_invalid=0 send_seq=26281 receive_seq=26281 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997785 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116256 bytes_read=2934980 bytes_retransmit=9 bytes_invalid=0 send_seq=15973 receive_seq=15973 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=38611 bytes_read=1579126 bytes_retransmit=9 bytes_invalid=0 send_seq=6376 receive_seq=6376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39097 bytes_read=117716 bytes_retransmit=9 bytes_invalid=0 send_seq=6363 receive_seq=6363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93189 bytes_read=2428630 bytes_retransmit=0 bytes_invalid=0 send_seq=10922 receive_seq=10922 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998686 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=55.7 th1: temp=54.8 th2: temp=60.5 th3: temp=58.0 sysload=0.18 cputime=456.519 memavail=7394636 print_time=6210.976 buffer_time=2.235 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6187.1: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27967722 bytes_read=4409296 bytes_retransmit=9 bytes_invalid=0 send_seq=529992 receive_seq=529992 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=20608 freq=400015963 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38350 bytes_read=120100 bytes_retransmit=0 bytes_invalid=0 send_seq=6363 receive_seq=6363 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999240 adj=49997287 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=189187 bytes_read=6018639 bytes_retransmit=9 bytes_invalid=0 send_seq=26291 receive_seq=26291 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997735 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116262 bytes_read=2935108 bytes_retransmit=9 bytes_invalid=0 send_seq=15974 receive_seq=15974 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=38617 bytes_read=1579375 bytes_retransmit=9 bytes_invalid=0 send_seq=6377 receive_seq=6377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997689 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39103 bytes_read=117743 bytes_retransmit=9 bytes_invalid=0 send_seq=6364 receive_seq=6364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93195 bytes_read=2428986 bytes_retransmit=0 bytes_invalid=0 send_seq=10923 receive_seq=10923 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998679 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=55.7 th1: temp=54.8 th2: temp=60.4 th3: temp=57.9 sysload=0.18 cputime=456.654 memavail=7394144 print_time=6211.903 buffer_time=2.162 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 103 Hz
Stats 6188.1: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27983424 bytes_read=4410946 bytes_retransmit=9 bytes_invalid=0 send_seq=530260 receive_seq=530260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=16925 freq=400015949 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38356 bytes_read=120116 bytes_retransmit=0 bytes_invalid=0 send_seq=6364 receive_seq=6364 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999242 adj=49997276 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=189263 bytes_read=6021713 bytes_retransmit=9 bytes_invalid=0 send_seq=26302 receive_seq=26302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997691 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116268 bytes_read=2935222 bytes_retransmit=9 bytes_invalid=0 send_seq=15975 receive_seq=15975 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=38623 bytes_read=1579654 bytes_retransmit=9 bytes_invalid=0 send_seq=6378 receive_seq=6378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39109 bytes_read=117759 bytes_retransmit=9 bytes_invalid=0 send_seq=6365 receive_seq=6365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93201 bytes_read=2429342 bytes_retransmit=0 bytes_invalid=0 send_seq=10924 receive_seq=10924 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998659 coil_temp=17.0 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=55.3 th1: temp=54.8 th2: temp=60.4 th3: temp=58.0 sysload=0.18 cputime=456.797 memavail=7393920 print_time=6212.778 buffer_time=2.037 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 104 Hz
Testing frequency 105 Hz
Stats 6189.1: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=27996741 bytes_read=4412401 bytes_retransmit=9 bytes_invalid=0 send_seq=530489 receive_seq=530489 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=21007 freq=400015950 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=38362 bytes_read=120145 bytes_retransmit=0 bytes_invalid=0 send_seq=6365 receive_seq=6365 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999244 adj=49997319 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=189339 bytes_read=6024770 bytes_retransmit=9 bytes_invalid=0 send_seq=26313 receive_seq=26313 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997694 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116274 bytes_read=2935322 bytes_retransmit=9 bytes_invalid=0 send_seq=15976 receive_seq=15976 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997534 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38629 bytes_read=1579903 bytes_retransmit=9 bytes_invalid=0 send_seq=6379 receive_seq=6379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39115 bytes_read=117775 bytes_retransmit=9 bytes_invalid=0 send_seq=6366 receive_seq=6366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93207 bytes_read=2429698 bytes_retransmit=0 bytes_invalid=0 send_seq=10925 receive_seq=10925 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998717 coil_temp=17.0 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=55.5 th1: temp=54.8 th2: temp=60.5 th3: temp=58.0 sysload=0.18 cputime=456.950 memavail=7393920 print_time=6213.983 buffer_time=2.240 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6190.1: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28011504 bytes_read=4414005 bytes_retransmit=9 bytes_invalid=0 send_seq=530742 receive_seq=530742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=21271 freq=400015952 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=38368 bytes_read=120161 bytes_retransmit=0 bytes_invalid=0 send_seq=6366 receive_seq=6366 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999247 adj=49997322 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=189415 bytes_read=6027915 bytes_retransmit=9 bytes_invalid=0 send_seq=26324 receive_seq=26324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997656 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116280 bytes_read=2935450 bytes_retransmit=9 bytes_invalid=0 send_seq=15977 receive_seq=15977 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997516 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38635 bytes_read=1580152 bytes_retransmit=9 bytes_invalid=0 send_seq=6380 receive_seq=6380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39121 bytes_read=117791 bytes_retransmit=9 bytes_invalid=0 send_seq=6367 receive_seq=6367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93213 bytes_read=2430054 bytes_retransmit=0 bytes_invalid=0 send_seq=10926 receive_seq=10926 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998728 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=55.5 th1: temp=54.9 th2: temp=60.2 th3: temp=58.0 sysload=0.16 cputime=457.090 memavail=7393692 print_time=6214.914 buffer_time=2.171 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 106 Hz
Stats 6191.1: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28027497 bytes_read=4415690 bytes_retransmit=9 bytes_invalid=0 send_seq=531017 receive_seq=531017 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=17400 freq=400015997 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=38374 bytes_read=120177 bytes_retransmit=0 bytes_invalid=0 send_seq=6367 receive_seq=6367 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999250 adj=49997342 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=189491 bytes_read=6030972 bytes_retransmit=9 bytes_invalid=0 send_seq=26335 receive_seq=26335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997650 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116286 bytes_read=2935550 bytes_retransmit=9 bytes_invalid=0 send_seq=15978 receive_seq=15978 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38641 bytes_read=1580431 bytes_retransmit=9 bytes_invalid=0 send_seq=6381 receive_seq=6381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39127 bytes_read=117807 bytes_retransmit=9 bytes_invalid=0 send_seq=6368 receive_seq=6368 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93219 bytes_read=2430410 bytes_retransmit=0 bytes_invalid=0 send_seq=10927 receive_seq=10927 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998710 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=55.4 th1: temp=54.4 th2: temp=60.3 th3: temp=58.0 sysload=0.16 cputime=457.232 memavail=7393692 print_time=6215.783 buffer_time=2.041 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 107 Hz
Testing frequency 108 Hz
Stats 6192.1: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28041288 bytes_read=4417206 bytes_retransmit=9 bytes_invalid=0 send_seq=531255 receive_seq=531255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=21317 freq=400016058 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=38380 bytes_read=120193 bytes_retransmit=0 bytes_invalid=0 send_seq=6368 receive_seq=6368 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999253 adj=49997294 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=189567 bytes_read=6034046 bytes_retransmit=9 bytes_invalid=0 send_seq=26346 receive_seq=26346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997533 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116292 bytes_read=2935650 bytes_retransmit=9 bytes_invalid=0 send_seq=15979 receive_seq=15979 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997407 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38647 bytes_read=1580665 bytes_retransmit=9 bytes_invalid=0 send_seq=6382 receive_seq=6382 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997581 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39133 bytes_read=117834 bytes_retransmit=9 bytes_invalid=0 send_seq=6369 receive_seq=6369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93225 bytes_read=2430766 bytes_retransmit=0 bytes_invalid=0 send_seq=10928 receive_seq=10928 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998647 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=55.5 th1: temp=55.0 th2: temp=60.4 th3: temp=58.0 sysload=0.16 cputime=457.388 memavail=7393692 print_time=6216.986 buffer_time=2.240 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6193.1: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28056180 bytes_read=4418825 bytes_retransmit=9 bytes_invalid=0 send_seq=531511 receive_seq=531511 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=21837 freq=400016076 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=38386 bytes_read=120209 bytes_retransmit=0 bytes_invalid=0 send_seq=6369 receive_seq=6369 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999256 adj=49997229 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=189643 bytes_read=6037134 bytes_retransmit=9 bytes_invalid=0 send_seq=26357 receive_seq=26357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997431 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116298 bytes_read=2935792 bytes_retransmit=9 bytes_invalid=0 send_seq=15980 receive_seq=15980 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997322 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38653 bytes_read=1580914 bytes_retransmit=9 bytes_invalid=0 send_seq=6383 receive_seq=6383 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997505 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39139 bytes_read=117850 bytes_retransmit=9 bytes_invalid=0 send_seq=6370 receive_seq=6370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999405 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93231 bytes_read=2431122 bytes_retransmit=0 bytes_invalid=0 send_seq=10929 receive_seq=10929 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998592 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=55.6 th1: temp=54.8 th2: temp=60.3 th3: temp=58.0 sysload=0.16 cputime=457.530 memavail=7393692 print_time=6217.917 buffer_time=2.170 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 109 Hz
Stats 6194.1: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28072428 bytes_read=4420533 bytes_retransmit=9 bytes_invalid=0 send_seq=531791 receive_seq=531791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=17692 freq=400016054 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38392 bytes_read=120237 bytes_retransmit=0 bytes_invalid=0 send_seq=6370 receive_seq=6370 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999260 adj=49997244 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=189719 bytes_read=6040190 bytes_retransmit=9 bytes_invalid=0 send_seq=26368 receive_seq=26368 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997407 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116304 bytes_read=2935892 bytes_retransmit=9 bytes_invalid=0 send_seq=15981 receive_seq=15981 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997323 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38659 bytes_read=1581208 bytes_retransmit=9 bytes_invalid=0 send_seq=6384 receive_seq=6384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997495 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39145 bytes_read=117866 bytes_retransmit=9 bytes_invalid=0 send_seq=6371 receive_seq=6371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999401 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93237 bytes_read=2431478 bytes_retransmit=0 bytes_invalid=0 send_seq=10930 receive_seq=10930 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998577 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=55.6 th1: temp=54.8 th2: temp=60.5 th3: temp=58.0 sysload=0.16 cputime=457.677 memavail=7393692 print_time=6218.787 buffer_time=2.040 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 110 Hz
Testing frequency 111 Hz
Stats 6195.1: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28086433 bytes_read=4422067 bytes_retransmit=9 bytes_invalid=0 send_seq=532034 receive_seq=532034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=21841 freq=400016044 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38398 bytes_read=120252 bytes_retransmit=0 bytes_invalid=0 send_seq=6371 receive_seq=6371 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999263 adj=49997327 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=189795 bytes_read=6043249 bytes_retransmit=9 bytes_invalid=0 send_seq=26379 receive_seq=26379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997456 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116310 bytes_read=2935992 bytes_retransmit=9 bytes_invalid=0 send_seq=15982 receive_seq=15982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997376 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38665 bytes_read=1581442 bytes_retransmit=9 bytes_invalid=0 send_seq=6385 receive_seq=6385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997535 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39151 bytes_read=117882 bytes_retransmit=9 bytes_invalid=0 send_seq=6372 receive_seq=6372 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999413 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93243 bytes_read=2431834 bytes_retransmit=0 bytes_invalid=0 send_seq=10931 receive_seq=10931 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998598 coil_temp=17.0 refs=0 mcu_temp=20.27 supply_voltage=3.012 th0: temp=55.6 th1: temp=54.7 th2: temp=60.4 th3: temp=58.0 sysload=0.15 cputime=457.842 memavail=7393700 print_time=6219.992 buffer_time=2.243 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6196.1: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28101327 bytes_read=4423682 bytes_retransmit=9 bytes_invalid=0 send_seq=532292 receive_seq=532292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=22379 freq=400016031 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38404 bytes_read=120267 bytes_retransmit=0 bytes_invalid=0 send_seq=6372 receive_seq=6372 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999267 adj=49997361 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=189871 bytes_read=6046393 bytes_retransmit=9 bytes_invalid=0 send_seq=26390 receive_seq=26390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997528 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116316 bytes_read=2936120 bytes_retransmit=9 bytes_invalid=0 send_seq=15983 receive_seq=15983 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997425 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38671 bytes_read=1581706 bytes_retransmit=9 bytes_invalid=0 send_seq=6386 receive_seq=6386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997573 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39157 bytes_read=117898 bytes_retransmit=9 bytes_invalid=0 send_seq=6373 receive_seq=6373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999423 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93249 bytes_read=2432190 bytes_retransmit=0 bytes_invalid=0 send_seq=10932 receive_seq=10932 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998622 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=55.6 th1: temp=55.0 th2: temp=60.5 th3: temp=58.0 sysload=0.15 cputime=457.987 memavail=7393700 print_time=6220.918 buffer_time=2.168 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 112 Hz
Stats 6197.1: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28118096 bytes_read=4425418 bytes_retransmit=9 bytes_invalid=0 send_seq=532574 receive_seq=532574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=17832 freq=400016013 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38410 bytes_read=120282 bytes_retransmit=0 bytes_invalid=0 send_seq=6373 receive_seq=6373 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999271 adj=49997411 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=189947 bytes_read=6049466 bytes_retransmit=9 bytes_invalid=0 send_seq=26401 receive_seq=26401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997584 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116322 bytes_read=2936220 bytes_retransmit=9 bytes_invalid=0 send_seq=15984 receive_seq=15984 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997458 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38677 bytes_read=1581970 bytes_retransmit=9 bytes_invalid=0 send_seq=6387 receive_seq=6387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997594 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39163 bytes_read=117925 bytes_retransmit=9 bytes_invalid=0 send_seq=6374 receive_seq=6374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93255 bytes_read=2432546 bytes_retransmit=0 bytes_invalid=0 send_seq=10933 receive_seq=10933 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998638 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=55.8 th1: temp=54.8 th2: temp=60.4 th3: temp=58.0 sysload=0.15 cputime=458.132 memavail=7393444 print_time=6221.792 buffer_time=2.042 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 113 Hz
Testing frequency 114 Hz
Stats 6198.1: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28132417 bytes_read=4426977 bytes_retransmit=9 bytes_invalid=0 send_seq=532821 receive_seq=532821 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=21743 freq=400015993 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38416 bytes_read=120297 bytes_retransmit=0 bytes_invalid=0 send_seq=6374 receive_seq=6374 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999275 adj=49997475 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=190016 bytes_read=6052499 bytes_retransmit=9 bytes_invalid=0 send_seq=26411 receive_seq=26411 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997624 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116328 bytes_read=2936334 bytes_retransmit=9 bytes_invalid=0 send_seq=15985 receive_seq=15985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997494 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38683 bytes_read=1582204 bytes_retransmit=9 bytes_invalid=0 send_seq=6388 receive_seq=6388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39169 bytes_read=117941 bytes_retransmit=9 bytes_invalid=0 send_seq=6375 receive_seq=6375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93261 bytes_read=2432902 bytes_retransmit=0 bytes_invalid=0 send_seq=10934 receive_seq=10934 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998684 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=55.7 th1: temp=54.6 th2: temp=60.5 th3: temp=58.0 sysload=0.15 cputime=458.291 memavail=7393720 print_time=6222.995 buffer_time=2.239 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6199.1: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28147236 bytes_read=4428577 bytes_retransmit=9 bytes_invalid=0 send_seq=533076 receive_seq=533076 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=22756 freq=400016108 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38422 bytes_read=120326 bytes_retransmit=0 bytes_invalid=0 send_seq=6375 receive_seq=6375 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999280 adj=49997491 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=190092 bytes_read=6055584 bytes_retransmit=9 bytes_invalid=0 send_seq=26422 receive_seq=26422 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997646 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116334 bytes_read=2936462 bytes_retransmit=9 bytes_invalid=0 send_seq=15986 receive_seq=15986 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38689 bytes_read=1582483 bytes_retransmit=9 bytes_invalid=0 send_seq=6389 receive_seq=6389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39175 bytes_read=117957 bytes_retransmit=9 bytes_invalid=0 send_seq=6376 receive_seq=6376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93267 bytes_read=2433258 bytes_retransmit=0 bytes_invalid=0 send_seq=10935 receive_seq=10935 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998702 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=55.6 th1: temp=54.9 th2: temp=60.6 th3: temp=58.1 sysload=0.15 cputime=458.433 memavail=7393720 print_time=6223.927 buffer_time=2.171 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 115 Hz
Stats 6200.1: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28163982 bytes_read=4430322 bytes_retransmit=9 bytes_invalid=0 send_seq=533363 receive_seq=533363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=18552 freq=400016178 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38428 bytes_read=120342 bytes_retransmit=0 bytes_invalid=0 send_seq=6376 receive_seq=6376 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999285 adj=49997343 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=190168 bytes_read=6058640 bytes_retransmit=9 bytes_invalid=0 send_seq=26433 receive_seq=26433 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997410 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116340 bytes_read=2936562 bytes_retransmit=9 bytes_invalid=0 send_seq=15987 receive_seq=15987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997288 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38695 bytes_read=1582747 bytes_retransmit=9 bytes_invalid=0 send_seq=6390 receive_seq=6390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997489 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39181 bytes_read=117973 bytes_retransmit=9 bytes_invalid=0 send_seq=6377 receive_seq=6377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999398 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93273 bytes_read=2433614 bytes_retransmit=0 bytes_invalid=0 send_seq=10936 receive_seq=10936 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998588 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=55.8 th1: temp=54.9 th2: temp=60.4 th3: temp=58.0 sysload=0.14 cputime=458.580 memavail=7393720 print_time=6224.798 buffer_time=2.041 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 116 Hz
Testing frequency 117 Hz
Stats 6201.1: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28178755 bytes_read=4431951 bytes_retransmit=9 bytes_invalid=0 send_seq=533621 receive_seq=533621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=22319 freq=400016147 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38434 bytes_read=120358 bytes_retransmit=0 bytes_invalid=0 send_seq=6377 receive_seq=6377 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999293 adj=49997293 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=190244 bytes_read=6061755 bytes_retransmit=9 bytes_invalid=0 send_seq=26444 receive_seq=26444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997310 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116346 bytes_read=2936662 bytes_retransmit=9 bytes_invalid=0 send_seq=15988 receive_seq=15988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997170 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38701 bytes_read=1582981 bytes_retransmit=9 bytes_invalid=0 send_seq=6391 receive_seq=6391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997388 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39187 bytes_read=117989 bytes_retransmit=9 bytes_invalid=0 send_seq=6378 receive_seq=6378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999380 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93279 bytes_read=2433970 bytes_retransmit=0 bytes_invalid=0 send_seq=10937 receive_seq=10937 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998538 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=55.6 th1: temp=54.9 th2: temp=60.4 th3: temp=57.9 sysload=0.14 cputime=458.748 memavail=7393720 print_time=6225.996 buffer_time=2.233 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6202.1: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28193931 bytes_read=4433572 bytes_retransmit=9 bytes_invalid=0 send_seq=533880 receive_seq=533880 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=23195 freq=400016165 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38440 bytes_read=120374 bytes_retransmit=0 bytes_invalid=0 send_seq=6378 receive_seq=6378 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999298 adj=49997417 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=190320 bytes_read=6064858 bytes_retransmit=9 bytes_invalid=0 send_seq=26455 receive_seq=26455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997451 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116352 bytes_read=2936790 bytes_retransmit=9 bytes_invalid=0 send_seq=15989 receive_seq=15989 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997328 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38707 bytes_read=1583260 bytes_retransmit=9 bytes_invalid=0 send_seq=6392 receive_seq=6392 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997513 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39193 bytes_read=118016 bytes_retransmit=9 bytes_invalid=0 send_seq=6379 receive_seq=6379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999406 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93285 bytes_read=2434326 bytes_retransmit=0 bytes_invalid=0 send_seq=10938 receive_seq=10938 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998588 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.012 th0: temp=55.6 th1: temp=54.9 th2: temp=60.4 th3: temp=58.0 sysload=0.14 cputime=458.890 memavail=7393720 print_time=6226.934 buffer_time=2.170 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 118 Hz
Stats 6203.1: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28211115 bytes_read=4435337 bytes_retransmit=9 bytes_invalid=0 send_seq=534171 receive_seq=534171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=18680 freq=400016149 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38446 bytes_read=120390 bytes_retransmit=0 bytes_invalid=0 send_seq=6379 receive_seq=6379 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999305 adj=49997430 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=190396 bytes_read=6067915 bytes_retransmit=9 bytes_invalid=0 send_seq=26466 receive_seq=26466 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997422 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=116358 bytes_read=2936904 bytes_retransmit=9 bytes_invalid=0 send_seq=15990 receive_seq=15990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997308 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=38713 bytes_read=1583509 bytes_retransmit=9 bytes_invalid=0 send_seq=6393 receive_seq=6393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997497 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39199 bytes_read=118032 bytes_retransmit=9 bytes_invalid=0 send_seq=6380 receive_seq=6380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999402 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93291 bytes_read=2434682 bytes_retransmit=0 bytes_invalid=0 send_seq=10939 receive_seq=10939 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998619 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=55.6 th1: temp=55.1 th2: temp=60.5 th3: temp=58.0 sysload=0.14 cputime=459.051 memavail=7392820 print_time=6227.799 buffer_time=2.034 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 119 Hz
Testing frequency 120 Hz
Stats 6204.1: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28225912 bytes_read=4436946 bytes_retransmit=9 bytes_invalid=0 send_seq=534426 receive_seq=534425 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=22290 freq=400016134 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38452 bytes_read=120419 bytes_retransmit=0 bytes_invalid=0 send_seq=6380 receive_seq=6380 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999310 adj=49997535 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=190472 bytes_read=6070971 bytes_retransmit=9 bytes_invalid=0 send_seq=26477 receive_seq=26477 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997466 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=116364 bytes_read=2937004 bytes_retransmit=9 bytes_invalid=0 send_seq=15991 receive_seq=15991 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997353 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38719 bytes_read=1583758 bytes_retransmit=9 bytes_invalid=0 send_seq=6394 receive_seq=6394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997527 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39205 bytes_read=118048 bytes_retransmit=9 bytes_invalid=0 send_seq=6381 receive_seq=6381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999411 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93297 bytes_read=2435038 bytes_retransmit=0 bytes_invalid=0 send_seq=10940 receive_seq=10940 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998626 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=55.6 th1: temp=54.8 th2: temp=60.6 th3: temp=58.1 sysload=0.14 cputime=459.215 memavail=7392820 print_time=6229.001 buffer_time=2.234 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 6205.1: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28241194 bytes_read=4438572 bytes_retransmit=9 bytes_invalid=0 send_seq=534689 receive_seq=534689 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=23175 freq=400016111 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38458 bytes_read=120435 bytes_retransmit=0 bytes_invalid=0 send_seq=6381 receive_seq=6381 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999316 adj=49997539 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=190548 bytes_read=6074056 bytes_retransmit=9 bytes_invalid=0 send_seq=26488 receive_seq=26488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997546 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=116370 bytes_read=2937132 bytes_retransmit=9 bytes_invalid=0 send_seq=15992 receive_seq=15992 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997416 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38725 bytes_read=1584037 bytes_retransmit=9 bytes_invalid=0 send_seq=6395 receive_seq=6395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997578 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39211 bytes_read=118064 bytes_retransmit=9 bytes_invalid=0 send_seq=6382 receive_seq=6382 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999422 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93303 bytes_read=2435394 bytes_retransmit=0 bytes_invalid=0 send_seq=10941 receive_seq=10941 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998632 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=55.3 th1: temp=54.8 th2: temp=60.5 th3: temp=58.1 sysload=0.13 cputime=459.361 memavail=7392820 print_time=6229.930 buffer_time=2.163 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 121 Hz
Stats 6206.1: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28258234 bytes_read=4440341 bytes_retransmit=9 bytes_invalid=0 send_seq=534981 receive_seq=534981 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=19024 freq=400016086 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38464 bytes_read=120451 bytes_retransmit=0 bytes_invalid=0 send_seq=6382 receive_seq=6382 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999321 adj=49997620 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=190624 bytes_read=6077113 bytes_retransmit=9 bytes_invalid=0 send_seq=26499 receive_seq=26499 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997589 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=116376 bytes_read=2937232 bytes_retransmit=9 bytes_invalid=0 send_seq=15993 receive_seq=15993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997466 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38731 bytes_read=1584286 bytes_retransmit=9 bytes_invalid=0 send_seq=6396 receive_seq=6396 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997612 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39217 bytes_read=118080 bytes_retransmit=9 bytes_invalid=0 send_seq=6383 receive_seq=6383 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93309 bytes_read=2435750 bytes_retransmit=0 bytes_invalid=0 send_seq=10942 receive_seq=10942 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998649 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=55.3 th1: temp=55.2 th2: temp=60.5 th3: temp=58.1 sysload=0.13 cputime=459.517 memavail=7392364 print_time=6230.801 buffer_time=2.033 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 122 Hz
Testing frequency 123 Hz
Stats 6207.1: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28273388 bytes_read=4441996 bytes_retransmit=9 bytes_invalid=0 send_seq=535241 receive_seq=535241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=22655 freq=400016068 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38470 bytes_read=120467 bytes_retransmit=0 bytes_invalid=0 send_seq=6383 receive_seq=6383 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999327 adj=49997696 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=190700 bytes_read=6080246 bytes_retransmit=9 bytes_invalid=0 send_seq=26510 receive_seq=26510 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997634 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=116382 bytes_read=2937332 bytes_retransmit=9 bytes_invalid=0 send_seq=15994 receive_seq=15994 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997515 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38737 bytes_read=1584520 bytes_retransmit=9 bytes_invalid=0 send_seq=6397 receive_seq=6397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39223 bytes_read=118107 bytes_retransmit=9 bytes_invalid=0 send_seq=6384 receive_seq=6384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93315 bytes_read=2436106 bytes_retransmit=0 bytes_invalid=0 send_seq=10943 receive_seq=10943 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998678 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=55.6 th1: temp=55.0 th2: temp=60.4 th3: temp=58.1 sysload=0.13 cputime=459.691 memavail=7391356 print_time=6232.001 buffer_time=2.233 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6208.1: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28288605 bytes_read=4443611 bytes_retransmit=9 bytes_invalid=0 send_seq=535502 receive_seq=535502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=23836 freq=400016062 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38476 bytes_read=120483 bytes_retransmit=0 bytes_invalid=0 send_seq=6384 receive_seq=6384 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999332 adj=49997668 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=190776 bytes_read=6083330 bytes_retransmit=9 bytes_invalid=0 send_seq=26521 receive_seq=26521 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997673 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116388 bytes_read=2937474 bytes_retransmit=9 bytes_invalid=0 send_seq=15995 receive_seq=15995 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997534 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38743 bytes_read=1584814 bytes_retransmit=9 bytes_invalid=0 send_seq=6398 receive_seq=6398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39229 bytes_read=118123 bytes_retransmit=9 bytes_invalid=0 send_seq=6385 receive_seq=6385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.7 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93321 bytes_read=2436462 bytes_retransmit=0 bytes_invalid=0 send_seq=10944 receive_seq=10944 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998675 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=55.6 th1: temp=54.9 th2: temp=60.4 th3: temp=58.1 sysload=0.13 cputime=459.843 memavail=7391356 print_time=6232.930 buffer_time=2.161 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 124 Hz
Stats 6209.1: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28305981 bytes_read=4445406 bytes_retransmit=9 bytes_invalid=0 send_seq=535799 receive_seq=535799 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=19376 freq=400016050 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38482 bytes_read=120512 bytes_retransmit=0 bytes_invalid=0 send_seq=6385 receive_seq=6385 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999337 adj=49997692 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=190852 bytes_read=6086386 bytes_retransmit=9 bytes_invalid=0 send_seq=26532 receive_seq=26532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997670 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116394 bytes_read=2937574 bytes_retransmit=9 bytes_invalid=0 send_seq=15996 receive_seq=15996 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997614 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38749 bytes_read=1585063 bytes_retransmit=9 bytes_invalid=0 send_seq=6399 receive_seq=6399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39235 bytes_read=118139 bytes_retransmit=9 bytes_invalid=0 send_seq=6386 receive_seq=6386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93327 bytes_read=2436818 bytes_retransmit=0 bytes_invalid=0 send_seq=10945 receive_seq=10945 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998672 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=55.5 th1: temp=55.0 th2: temp=60.6 th3: temp=58.1 sysload=0.13 cputime=459.995 memavail=7391356 print_time=6233.808 buffer_time=2.038 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 125 Hz
Testing frequency 126 Hz
Stats 6210.1: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28321427 bytes_read=4447080 bytes_retransmit=9 bytes_invalid=0 send_seq=536066 receive_seq=536066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=22798 freq=400016051 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38488 bytes_read=120528 bytes_retransmit=0 bytes_invalid=0 send_seq=6386 receive_seq=6386 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999342 adj=49997736 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=190921 bytes_read=6089420 bytes_retransmit=9 bytes_invalid=0 send_seq=26542 receive_seq=26542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997676 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116400 bytes_read=2937674 bytes_retransmit=9 bytes_invalid=0 send_seq=15997 receive_seq=15997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997633 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38755 bytes_read=1585297 bytes_retransmit=9 bytes_invalid=0 send_seq=6400 receive_seq=6400 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39241 bytes_read=118155 bytes_retransmit=9 bytes_invalid=0 send_seq=6387 receive_seq=6387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93333 bytes_read=2437174 bytes_retransmit=0 bytes_invalid=0 send_seq=10946 receive_seq=10946 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998678 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=55.7 th1: temp=54.8 th2: temp=60.5 th3: temp=58.1 sysload=0.12 cputime=460.163 memavail=7391356 print_time=6235.008 buffer_time=2.237 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 127 Hz
Stats 6211.1: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28336819 bytes_read=4448715 bytes_retransmit=9 bytes_invalid=0 send_seq=536331 receive_seq=536331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=24044 freq=400016046 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38494 bytes_read=120544 bytes_retransmit=0 bytes_invalid=0 send_seq=6387 receive_seq=6387 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999347 adj=49997677 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=190997 bytes_read=6092506 bytes_retransmit=9 bytes_invalid=0 send_seq=26553 receive_seq=26553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997655 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116406 bytes_read=2937802 bytes_retransmit=9 bytes_invalid=0 send_seq=15998 receive_seq=15998 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997591 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38761 bytes_read=1585591 bytes_retransmit=9 bytes_invalid=0 send_seq=6401 receive_seq=6401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39247 bytes_read=118171 bytes_retransmit=9 bytes_invalid=0 send_seq=6388 receive_seq=6388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93339 bytes_read=2437530 bytes_retransmit=0 bytes_invalid=0 send_seq=10947 receive_seq=10947 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998674 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=55.8 th1: temp=54.8 th2: temp=60.5 th3: temp=58.1 sysload=0.12 cputime=460.314 memavail=7391364 print_time=6235.940 buffer_time=2.168 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6212.1: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28354317 bytes_read=4450536 bytes_retransmit=9 bytes_invalid=0 send_seq=536630 receive_seq=536630 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=19396 freq=400016223 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38500 bytes_read=120560 bytes_retransmit=0 bytes_invalid=0 send_seq=6388 receive_seq=6388 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999353 adj=49997697 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=191073 bytes_read=6095579 bytes_retransmit=9 bytes_invalid=0 send_seq=26564 receive_seq=26564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997737 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116412 bytes_read=2937902 bytes_retransmit=9 bytes_invalid=0 send_seq=15999 receive_seq=15999 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997591 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38767 bytes_read=1585825 bytes_retransmit=9 bytes_invalid=0 send_seq=6402 receive_seq=6402 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39253 bytes_read=118198 bytes_retransmit=9 bytes_invalid=0 send_seq=6389 receive_seq=6389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93345 bytes_read=2437886 bytes_retransmit=0 bytes_invalid=0 send_seq=10948 receive_seq=10948 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998665 coil_temp=17.0 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=55.5 th1: temp=55.1 th2: temp=60.5 th3: temp=58.1 sysload=0.12 cputime=460.464 memavail=7391364 print_time=6236.809 buffer_time=2.037 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 128 Hz
Testing frequency 129 Hz
Stats 6213.1: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28369741 bytes_read=4452210 bytes_retransmit=9 bytes_invalid=0 send_seq=536897 receive_seq=536897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=23025 freq=400016438 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38506 bytes_read=120576 bytes_retransmit=0 bytes_invalid=0 send_seq=6389 receive_seq=6389 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999360 adj=49997446 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=191149 bytes_read=6098697 bytes_retransmit=9 bytes_invalid=0 send_seq=26575 receive_seq=26575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997363 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116418 bytes_read=2938016 bytes_retransmit=9 bytes_invalid=0 send_seq=16000 receive_seq=16000 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997237 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38773 bytes_read=1586059 bytes_retransmit=9 bytes_invalid=0 send_seq=6403 receive_seq=6403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997387 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39259 bytes_read=118214 bytes_retransmit=9 bytes_invalid=0 send_seq=6390 receive_seq=6390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999378 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93351 bytes_read=2438242 bytes_retransmit=0 bytes_invalid=0 send_seq=10949 receive_seq=10949 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998517 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=55.7 th1: temp=55.0 th2: temp=60.5 th3: temp=58.2 sysload=0.12 cputime=460.633 memavail=7391364 print_time=6238.016 buffer_time=2.243 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 130 Hz
Stats 6214.1: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28385090 bytes_read=4453835 bytes_retransmit=9 bytes_invalid=0 send_seq=537160 receive_seq=537160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=24284 freq=400016399 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38512 bytes_read=120605 bytes_retransmit=0 bytes_invalid=0 send_seq=6390 receive_seq=6390 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999365 adj=49997169 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=191225 bytes_read=6101782 bytes_retransmit=9 bytes_invalid=0 send_seq=26586 receive_seq=26586 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997029 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116424 bytes_read=2938144 bytes_retransmit=9 bytes_invalid=0 send_seq=16001 receive_seq=16001 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63996898 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38779 bytes_read=1586368 bytes_retransmit=9 bytes_invalid=0 send_seq=6404 receive_seq=6404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997144 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39265 bytes_read=118230 bytes_retransmit=9 bytes_invalid=0 send_seq=6391 receive_seq=6391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999316 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93357 bytes_read=2438598 bytes_retransmit=0 bytes_invalid=0 send_seq=10950 receive_seq=10950 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998345 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=55.7 th1: temp=54.9 th2: temp=60.5 th3: temp=58.2 sysload=0.12 cputime=460.782 memavail=7391372 print_time=6238.940 buffer_time=2.167 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6215.1: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28402688 bytes_read=4455661 bytes_retransmit=9 bytes_invalid=0 send_seq=537461 receive_seq=537461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=20060 freq=400016353 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38524 bytes_read=120637 bytes_retransmit=0 bytes_invalid=0 send_seq=6392 receive_seq=6392 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999378 adj=49997310 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=191307 bytes_read=6104855 bytes_retransmit=9 bytes_invalid=0 send_seq=26598 receive_seq=26598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997228 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116436 bytes_read=2938260 bytes_retransmit=9 bytes_invalid=0 send_seq=16003 receive_seq=16003 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997164 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38791 bytes_read=1586618 bytes_retransmit=9 bytes_invalid=0 send_seq=6406 receive_seq=6406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997256 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39277 bytes_read=118262 bytes_retransmit=9 bytes_invalid=0 send_seq=6393 receive_seq=6393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999345 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93369 bytes_read=2438970 bytes_retransmit=0 bytes_invalid=0 send_seq=10952 receive_seq=10952 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998412 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=55.6 th1: temp=55.1 th2: temp=60.6 th3: temp=58.1 sysload=0.11 cputime=460.934 memavail=7391372 print_time=6239.812 buffer_time=2.038 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 131 Hz
Testing frequency 132 Hz
Stats 6216.1: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28418553 bytes_read=4457373 bytes_retransmit=9 bytes_invalid=0 send_seq=537737 receive_seq=537737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=23447 freq=400016352 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38530 bytes_read=120653 bytes_retransmit=0 bytes_invalid=0 send_seq=6393 receive_seq=6393 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999384 adj=49997561 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=191383 bytes_read=6107911 bytes_retransmit=9 bytes_invalid=0 send_seq=26609 receive_seq=26609 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997469 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116442 bytes_read=2938360 bytes_retransmit=9 bytes_invalid=0 send_seq=16004 receive_seq=16004 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000076 adj=63997274 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38797 bytes_read=1586852 bytes_retransmit=9 bytes_invalid=0 send_seq=6407 receive_seq=6407 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997370 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39283 bytes_read=118278 bytes_retransmit=9 bytes_invalid=0 send_seq=6394 receive_seq=6394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999381 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93375 bytes_read=2439326 bytes_retransmit=0 bytes_invalid=0 send_seq=10953 receive_seq=10953 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998471 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=55.7 th1: temp=55.1 th2: temp=60.6 th3: temp=58.1 sysload=0.11 cputime=461.106 memavail=7391372 print_time=6241.016 buffer_time=2.241 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Stats 6217.1: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28434252 bytes_read=4459034 bytes_retransmit=9 bytes_invalid=0 send_seq=538005 receive_seq=538004 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=25976 freq=400016314 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38536 bytes_read=120669 bytes_retransmit=0 bytes_invalid=0 send_seq=6394 receive_seq=6394 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999389 adj=49997562 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=191459 bytes_read=6111012 bytes_retransmit=9 bytes_invalid=0 send_seq=26620 receive_seq=26620 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997498 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116448 bytes_read=2938486 bytes_retransmit=9 bytes_invalid=0 send_seq=16005 receive_seq=16005 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000074 adj=63997406 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38803 bytes_read=1587146 bytes_retransmit=9 bytes_invalid=0 send_seq=6408 receive_seq=6408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997437 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39289 bytes_read=118305 bytes_retransmit=9 bytes_invalid=0 send_seq=6395 receive_seq=6395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999395 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93381 bytes_read=2439682 bytes_retransmit=0 bytes_invalid=0 send_seq=10954 receive_seq=10954 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999948 adj=31998588 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=55.7 th1: temp=55.0 th2: temp=60.5 th3: temp=58.2 sysload=0.11 cputime=461.262 memavail=7391148 print_time=6241.993 buffer_time=2.218 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6218.1: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28451900 bytes_read=4460834 bytes_retransmit=9 bytes_invalid=0 send_seq=538302 receive_seq=538302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=9972 freq=400016305 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38542 bytes_read=120685 bytes_retransmit=0 bytes_invalid=0 send_seq=6395 receive_seq=6395 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999394 adj=49997642 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=191535 bytes_read=6114052 bytes_retransmit=9 bytes_invalid=0 send_seq=26631 receive_seq=26631 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997668 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116454 bytes_read=2938593 bytes_retransmit=9 bytes_invalid=0 send_seq=16006 receive_seq=16006 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000074 adj=63997463 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38809 bytes_read=1587380 bytes_retransmit=9 bytes_invalid=0 send_seq=6409 receive_seq=6409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997512 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39295 bytes_read=118321 bytes_retransmit=9 bytes_invalid=0 send_seq=6396 receive_seq=6396 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999412 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93387 bytes_read=2440038 bytes_retransmit=0 bytes_invalid=0 send_seq=10955 receive_seq=10955 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999947 adj=31998653 coil_temp=17.0 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=55.8 th1: temp=55.0 th2: temp=60.7 th3: temp=58.2 sysload=0.11 cputime=461.357 memavail=7391172 print_time=6241.993 buffer_time=1.217 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6219.1: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28463065 bytes_read=4462143 bytes_retransmit=9 bytes_invalid=0 send_seq=538496 receive_seq=538496 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016265 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38548 bytes_read=120714 bytes_retransmit=0 bytes_invalid=0 send_seq=6396 receive_seq=6396 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999398 adj=49997706 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=191611 bytes_read=6117092 bytes_retransmit=9 bytes_invalid=0 send_seq=26642 receive_seq=26642 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997739 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116460 bytes_read=2938686 bytes_retransmit=9 bytes_invalid=0 send_seq=16007 receive_seq=16007 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997473 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38815 bytes_read=1587629 bytes_retransmit=9 bytes_invalid=0 send_seq=6410 receive_seq=6410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997552 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39301 bytes_read=118337 bytes_retransmit=9 bytes_invalid=0 send_seq=6397 receive_seq=6397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999414 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93393 bytes_read=2440394 bytes_retransmit=0 bytes_invalid=0 send_seq=10956 receive_seq=10956 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998647 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=55.7 th1: temp=54.9 th2: temp=60.6 th3: temp=58.2 sysload=0.11 cputime=461.438 memavail=7391172 print_time=6241.993 buffer_time=0.217 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
LIS2DW finished 'toolboard_t0' measurements
Resonances data written to /tmp/resonances_y_125.000_250.000_20.000_t0_copy.csv file
Probing point (125.000, 250.000, 20.000)
Stats 6220.1: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28463754 bytes_read=4462603 bytes_retransmit=9 bytes_invalid=0 send_seq=538526 receive_seq=538526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016227 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38554 bytes_read=120730 bytes_retransmit=0 bytes_invalid=0 send_seq=6397 receive_seq=6397 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999402 adj=49997817 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=191686 bytes_read=6118250 bytes_retransmit=9 bytes_invalid=0 send_seq=26651 receive_seq=26651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997797 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116466 bytes_read=2938805 bytes_retransmit=9 bytes_invalid=0 send_seq=16008 receive_seq=16008 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997540 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38821 bytes_read=1587923 bytes_retransmit=9 bytes_invalid=0 send_seq=6411 receive_seq=6411 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997615 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39307 bytes_read=118353 bytes_retransmit=9 bytes_invalid=0 send_seq=6398 receive_seq=6398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93399 bytes_read=2440750 bytes_retransmit=0 bytes_invalid=0 send_seq=10957 receive_seq=10957 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998668 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=55.6 th1: temp=54.8 th2: temp=60.6 th3: temp=58.2 sysload=0.10 cputime=461.559 memavail=7395472 print_time=6242.983 buffer_time=0.206 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t1' measurements
toolhead: max_velocity: 600.000000
max_accel: 8379.841000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance testing
Testing frequency 10 Hz
Testing frequency 11 Hz
Testing frequency 12 Hz
Stats 6221.1: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28468749 bytes_read=4463408 bytes_retransmit=9 bytes_invalid=0 send_seq=538625 receive_seq=538625 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016192 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38560 bytes_read=120746 bytes_retransmit=0 bytes_invalid=0 send_seq=6398 receive_seq=6398 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999407 adj=49997949 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=191692 bytes_read=6118343 bytes_retransmit=9 bytes_invalid=0 send_seq=26652 receive_seq=26652 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997851 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116623 bytes_read=2941214 bytes_retransmit=9 bytes_invalid=0 send_seq=16026 receive_seq=16026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997631 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38827 bytes_read=1588157 bytes_retransmit=9 bytes_invalid=0 send_seq=6412 receive_seq=6412 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997694 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39313 bytes_read=118369 bytes_retransmit=9 bytes_invalid=0 send_seq=6399 receive_seq=6399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93405 bytes_read=2441106 bytes_retransmit=0 bytes_invalid=0 send_seq=10958 receive_seq=10958 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998710 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=55.8 th1: temp=54.8 th2: temp=60.7 th3: temp=58.2 sysload=0.10 cputime=461.733 memavail=7395260 print_time=6246.167 buffer_time=2.389 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 13 Hz
Stats 6222.1: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28470688 bytes_read=4464008 bytes_retransmit=9 bytes_invalid=0 send_seq=538674 receive_seq=538674 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=400016156 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38566 bytes_read=120762 bytes_retransmit=0 bytes_invalid=0 send_seq=6399 receive_seq=6399 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999412 adj=49997603 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=191698 bytes_read=6118443 bytes_retransmit=9 bytes_invalid=0 send_seq=26653 receive_seq=26653 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997718 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=116699 bytes_read=2944211 bytes_retransmit=9 bytes_invalid=0 send_seq=16037 receive_seq=16037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000074 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38833 bytes_read=1588391 bytes_retransmit=9 bytes_invalid=0 send_seq=6413 receive_seq=6413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39319 bytes_read=118396 bytes_retransmit=9 bytes_invalid=0 send_seq=6400 receive_seq=6400 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93411 bytes_read=2441462 bytes_retransmit=0 bytes_invalid=0 send_seq=10959 receive_seq=10959 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998690 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=55.4 th1: temp=55.1 th2: temp=60.6 th3: temp=58.4 sysload=0.10 cputime=461.809 memavail=7395260 print_time=6247.009 buffer_time=2.230 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 14 Hz
Stats 6223.1: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28473277 bytes_read=4464613 bytes_retransmit=9 bytes_invalid=0 send_seq=538733 receive_seq=538733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=0 freq=400016124 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38572 bytes_read=120778 bytes_retransmit=0 bytes_invalid=0 send_seq=6400 receive_seq=6400 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999416 adj=49997696 toolboard_t0: mcu_awake=0.150 mcu_task_avg=0.000111 mcu_task_stddev=0.000071 bytes_write=191704 bytes_read=6118588 bytes_retransmit=9 bytes_invalid=0 send_seq=26654 receive_seq=26654 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997754 toolboard_t1: mcu_awake=0.162 mcu_task_avg=0.000112 mcu_task_stddev=0.000071 bytes_write=116775 bytes_read=2947296 bytes_retransmit=9 bytes_invalid=0 send_seq=16048 receive_seq=16048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000081 adj=63997651 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38839 bytes_read=1588685 bytes_retransmit=9 bytes_invalid=0 send_seq=6414 receive_seq=6414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997747 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39325 bytes_read=118412 bytes_retransmit=9 bytes_invalid=0 send_seq=6401 receive_seq=6401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93417 bytes_read=2441818 bytes_retransmit=0 bytes_invalid=0 send_seq=10960 receive_seq=10960 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998714 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=55.5 th1: temp=55.1 th2: temp=60.6 th3: temp=58.2 sysload=0.10 cputime=461.887 memavail=7397132 print_time=6248.012 buffer_time=2.233 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 15 Hz
Stats 6224.1: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28475448 bytes_read=4465178 bytes_retransmit=9 bytes_invalid=0 send_seq=538784 receive_seq=538784 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016115 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38578 bytes_read=120807 bytes_retransmit=0 bytes_invalid=0 send_seq=6401 receive_seq=6401 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999421 adj=49997742 toolboard_t0: mcu_awake=0.150 mcu_task_avg=0.000111 mcu_task_stddev=0.000071 bytes_write=191710 bytes_read=6118688 bytes_retransmit=9 bytes_invalid=0 send_seq=26655 receive_seq=26655 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997792 toolboard_t1: mcu_awake=0.162 mcu_task_avg=0.000112 mcu_task_stddev=0.000071 bytes_write=116851 bytes_read=2950353 bytes_retransmit=9 bytes_invalid=0 send_seq=16059 receive_seq=16059 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000087 adj=63997764 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38845 bytes_read=1588934 bytes_retransmit=9 bytes_invalid=0 send_seq=6415 receive_seq=6415 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997765 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39331 bytes_read=118428 bytes_retransmit=9 bytes_invalid=0 send_seq=6402 receive_seq=6402 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999468 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93423 bytes_read=2442174 bytes_retransmit=0 bytes_invalid=0 send_seq=10961 receive_seq=10961 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998731 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=55.5 th1: temp=55.0 th2: temp=60.8 th3: temp=58.3 sysload=0.10 cputime=461.964 memavail=7397132 print_time=6248.883 buffer_time=2.104 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 16 Hz
Stats 6225.1: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28478210 bytes_read=4465827 bytes_retransmit=9 bytes_invalid=0 send_seq=538846 receive_seq=538846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016084 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38584 bytes_read=120823 bytes_retransmit=0 bytes_invalid=0 send_seq=6402 receive_seq=6402 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999427 adj=49997786 toolboard_t0: mcu_awake=0.150 mcu_task_avg=0.000111 mcu_task_stddev=0.000071 bytes_write=191716 bytes_read=6118788 bytes_retransmit=9 bytes_invalid=0 send_seq=26656 receive_seq=26656 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997783 toolboard_t1: mcu_awake=0.162 mcu_task_avg=0.000112 mcu_task_stddev=0.000071 bytes_write=116927 bytes_read=2953410 bytes_retransmit=9 bytes_invalid=0 send_seq=16070 receive_seq=16070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000086 adj=63997828 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38851 bytes_read=1589168 bytes_retransmit=9 bytes_invalid=0 send_seq=6416 receive_seq=6416 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997764 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39337 bytes_read=118444 bytes_retransmit=9 bytes_invalid=0 send_seq=6403 receive_seq=6403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999466 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93429 bytes_read=2442530 bytes_retransmit=0 bytes_invalid=0 send_seq=10962 receive_seq=10962 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998716 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.9 th2: temp=60.7 th3: temp=58.3 sysload=0.09 cputime=462.041 memavail=7396656 print_time=6249.832 buffer_time=2.052 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 17 Hz
Stats 6226.1: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28481449 bytes_read=4466487 bytes_retransmit=9 bytes_invalid=0 send_seq=538916 receive_seq=538916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=0 freq=400016059 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38590 bytes_read=120839 bytes_retransmit=0 bytes_invalid=0 send_seq=6403 receive_seq=6403 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999432 adj=49997841 toolboard_t0: mcu_awake=0.150 mcu_task_avg=0.000111 mcu_task_stddev=0.000071 bytes_write=191722 bytes_read=6118916 bytes_retransmit=9 bytes_invalid=0 send_seq=26657 receive_seq=26657 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997883 toolboard_t1: mcu_awake=0.162 mcu_task_avg=0.000112 mcu_task_stddev=0.000071 bytes_write=117003 bytes_read=2956554 bytes_retransmit=9 bytes_invalid=0 send_seq=16081 receive_seq=16081 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000083 adj=63997822 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38857 bytes_read=1589462 bytes_retransmit=9 bytes_invalid=0 send_seq=6417 receive_seq=6417 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997782 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39343 bytes_read=118460 bytes_retransmit=9 bytes_invalid=0 send_seq=6404 receive_seq=6404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999474 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93435 bytes_read=2442886 bytes_retransmit=0 bytes_invalid=0 send_seq=10963 receive_seq=10963 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998721 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=55.6 th1: temp=55.1 th2: temp=60.9 th3: temp=58.5 sysload=0.09 cputime=462.127 memavail=7396656 print_time=6251.021 buffer_time=2.240 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 18 Hz
Stats 6227.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=28483951 bytes_read=4467097 bytes_retransmit=9 bytes_invalid=0 send_seq=538974 receive_seq=538974 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=0 freq=400016030 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38596 bytes_read=120855 bytes_retransmit=0 bytes_invalid=0 send_seq=6404 receive_seq=6404 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999438 adj=49997819 toolboard_t0: mcu_awake=0.150 mcu_task_avg=0.000111 mcu_task_stddev=0.000071 bytes_write=191728 bytes_read=6119016 bytes_retransmit=9 bytes_invalid=0 send_seq=26658 receive_seq=26658 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997855 toolboard_t1: mcu_awake=0.162 mcu_task_avg=0.000112 mcu_task_stddev=0.000071 bytes_write=117079 bytes_read=2959613 bytes_retransmit=9 bytes_invalid=0 send_seq=16092 receive_seq=16092 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000080 adj=63997745 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38863 bytes_read=1589696 bytes_retransmit=9 bytes_invalid=0 send_seq=6418 receive_seq=6418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997779 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39349 bytes_read=118487 bytes_retransmit=9 bytes_invalid=0 send_seq=6405 receive_seq=6405 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999474 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93441 bytes_read=2443242 bytes_retransmit=0 bytes_invalid=0 send_seq=10964 receive_seq=10964 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998718 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=55.6 th1: temp=54.9 th2: temp=60.9 th3: temp=58.4 sysload=0.09 cputime=462.207 memavail=7394916 print_time=6251.981 buffer_time=2.200 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 19 Hz
Stats 6228.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=28486851 bytes_read=4467756 bytes_retransmit=9 bytes_invalid=0 send_seq=539038 receive_seq=539038 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=0 freq=400016014 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38602 bytes_read=120871 bytes_retransmit=0 bytes_invalid=0 send_seq=6405 receive_seq=6405 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999443 adj=49997870 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=191734 bytes_read=6119130 bytes_retransmit=9 bytes_invalid=0 send_seq=26659 receive_seq=26659 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997857 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=117155 bytes_read=2962688 bytes_retransmit=9 bytes_invalid=0 send_seq=16103 receive_seq=16103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000078 adj=63997730 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38869 bytes_read=1589930 bytes_retransmit=9 bytes_invalid=0 send_seq=6419 receive_seq=6419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997815 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39355 bytes_read=118503 bytes_retransmit=9 bytes_invalid=0 send_seq=6406 receive_seq=6406 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999478 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93447 bytes_read=2443598 bytes_retransmit=0 bytes_invalid=0 send_seq=10965 receive_seq=10965 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998725 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.012 th0: temp=55.5 th1: temp=55.2 th2: temp=60.9 th3: temp=58.6 sysload=0.09 cputime=462.287 memavail=7395984 print_time=6252.828 buffer_time=2.046 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 20 Hz
Stats 6229.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=28489556 bytes_read=4468366 bytes_retransmit=9 bytes_invalid=0 send_seq=539098 receive_seq=539098 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015992 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38608 bytes_read=120900 bytes_retransmit=0 bytes_invalid=0 send_seq=6406 receive_seq=6406 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999447 adj=49997919 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=191740 bytes_read=6119258 bytes_retransmit=9 bytes_invalid=0 send_seq=26660 receive_seq=26660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997939 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=117231 bytes_read=2965773 bytes_retransmit=9 bytes_invalid=0 send_seq=16114 receive_seq=16114 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000076 adj=63997715 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38875 bytes_read=1590239 bytes_retransmit=9 bytes_invalid=0 send_seq=6420 receive_seq=6420 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997812 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39361 bytes_read=118519 bytes_retransmit=9 bytes_invalid=0 send_seq=6407 receive_seq=6407 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999478 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93453 bytes_read=2443954 bytes_retransmit=0 bytes_invalid=0 send_seq=10966 receive_seq=10966 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998733 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=55.5 th1: temp=54.9 th2: temp=61.0 th3: temp=58.7 sysload=0.09 cputime=462.370 memavail=7395984 print_time=6253.794 buffer_time=2.012 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 21 Hz
Stats 6230.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=28493338 bytes_read=4469071 bytes_retransmit=9 bytes_invalid=0 send_seq=539177 receive_seq=539177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=0 freq=400015966 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38614 bytes_read=120916 bytes_retransmit=0 bytes_invalid=0 send_seq=6407 receive_seq=6407 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999452 adj=49997920 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=191746 bytes_read=6119358 bytes_retransmit=9 bytes_invalid=0 send_seq=26661 receive_seq=26661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997941 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=117307 bytes_read=2968832 bytes_retransmit=9 bytes_invalid=0 send_seq=16125 receive_seq=16125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000074 adj=63997700 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38881 bytes_read=1590473 bytes_retransmit=9 bytes_invalid=0 send_seq=6421 receive_seq=6421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997807 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39367 bytes_read=118535 bytes_retransmit=9 bytes_invalid=0 send_seq=6408 receive_seq=6408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999478 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93459 bytes_read=2444294 bytes_retransmit=0 bytes_invalid=0 send_seq=10967 receive_seq=10967 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998742 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=55.9 th1: temp=54.9 th2: temp=61.2 th3: temp=58.7 sysload=0.08 cputime=462.456 memavail=7395984 print_time=6255.027 buffer_time=2.245 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 22 Hz
Stats 6231.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=28496405 bytes_read=4469740 bytes_retransmit=9 bytes_invalid=0 send_seq=539243 receive_seq=539243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015942 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38620 bytes_read=120932 bytes_retransmit=0 bytes_invalid=0 send_seq=6408 receive_seq=6408 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999456 adj=49997867 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=191752 bytes_read=6119458 bytes_retransmit=9 bytes_invalid=0 send_seq=26662 receive_seq=26662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997873 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=117383 bytes_read=2971889 bytes_retransmit=9 bytes_invalid=0 send_seq=16136 receive_seq=16136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997668 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38887 bytes_read=1590707 bytes_retransmit=9 bytes_invalid=0 send_seq=6422 receive_seq=6422 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997806 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39373 bytes_read=118551 bytes_retransmit=9 bytes_invalid=0 send_seq=6409 receive_seq=6409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999474 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93465 bytes_read=2444650 bytes_retransmit=0 bytes_invalid=0 send_seq=10968 receive_seq=10968 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998736 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=55.4 th1: temp=55.0 th2: temp=61.2 th3: temp=58.7 sysload=0.08 cputime=462.534 memavail=7395984 print_time=6255.848 buffer_time=2.065 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 23 Hz
Stats 6232.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28499379 bytes_read=4470396 bytes_retransmit=9 bytes_invalid=0 send_seq=539309 receive_seq=539309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015945 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38626 bytes_read=120948 bytes_retransmit=0 bytes_invalid=0 send_seq=6409 receive_seq=6409 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999461 adj=49997933 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=191758 bytes_read=6119586 bytes_retransmit=9 bytes_invalid=0 send_seq=26663 receive_seq=26663 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997879 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=117452 bytes_read=2974950 bytes_retransmit=9 bytes_invalid=0 send_seq=16146 receive_seq=16146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997691 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38893 bytes_read=1591001 bytes_retransmit=9 bytes_invalid=0 send_seq=6423 receive_seq=6423 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997831 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39379 bytes_read=118578 bytes_retransmit=9 bytes_invalid=0 send_seq=6410 receive_seq=6410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999481 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93471 bytes_read=2445006 bytes_retransmit=0 bytes_invalid=0 send_seq=10969 receive_seq=10969 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998748 coil_temp=17.0 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=55.7 th1: temp=55.1 th2: temp=61.2 th3: temp=58.7 sysload=0.08 cputime=462.617 memavail=7395984 print_time=6256.823 buffer_time=2.039 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 24 Hz
Stats 6233.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28503476 bytes_read=4471126 bytes_retransmit=9 bytes_invalid=0 send_seq=539393 receive_seq=539393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=400015947 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38632 bytes_read=120964 bytes_retransmit=0 bytes_invalid=0 send_seq=6410 receive_seq=6410 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999464 adj=49997898 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191764 bytes_read=6119700 bytes_retransmit=9 bytes_invalid=0 send_seq=26664 receive_seq=26664 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997810 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=117528 bytes_read=2978024 bytes_retransmit=9 bytes_invalid=0 send_seq=16157 receive_seq=16157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000074 adj=63997640 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38899 bytes_read=1591235 bytes_retransmit=9 bytes_invalid=0 send_seq=6424 receive_seq=6424 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997781 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39385 bytes_read=118594 bytes_retransmit=9 bytes_invalid=0 send_seq=6411 receive_seq=6411 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999470 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93477 bytes_read=2445362 bytes_retransmit=0 bytes_invalid=0 send_seq=10970 receive_seq=10970 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998753 coil_temp=17.0 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=55.5 th1: temp=55.0 th2: temp=61.3 th3: temp=58.8 sysload=0.08 cputime=462.704 memavail=7395984 print_time=6258.044 buffer_time=2.260 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 25 Hz
Stats 6234.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28506767 bytes_read=4471820 bytes_retransmit=9 bytes_invalid=0 send_seq=539464 receive_seq=539464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=0 freq=400015923 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38638 bytes_read=120993 bytes_retransmit=0 bytes_invalid=0 send_seq=6411 receive_seq=6411 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999467 adj=49997801 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191770 bytes_read=6119800 bytes_retransmit=9 bytes_invalid=0 send_seq=26665 receive_seq=26665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997739 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=117604 bytes_read=2981140 bytes_retransmit=9 bytes_invalid=0 send_seq=16168 receive_seq=16168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997633 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38905 bytes_read=1591484 bytes_retransmit=9 bytes_invalid=0 send_seq=6425 receive_seq=6425 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997726 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39391 bytes_read=118610 bytes_retransmit=9 bytes_invalid=0 send_seq=6412 receive_seq=6412 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93483 bytes_read=2445718 bytes_retransmit=0 bytes_invalid=0 send_seq=10971 receive_seq=10971 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998718 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=55.7 th1: temp=55.1 th2: temp=61.5 th3: temp=58.8 sysload=0.08 cputime=462.784 memavail=7395984 print_time=6258.883 buffer_time=2.098 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 26 Hz
Stats 6235.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28510041 bytes_read=4472475 bytes_retransmit=9 bytes_invalid=0 send_seq=539533 receive_seq=539533 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015922 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38644 bytes_read=121009 bytes_retransmit=0 bytes_invalid=0 send_seq=6412 receive_seq=6412 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999471 adj=49997855 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191776 bytes_read=6119928 bytes_retransmit=9 bytes_invalid=0 send_seq=26666 receive_seq=26666 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997756 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=117680 bytes_read=2984229 bytes_retransmit=9 bytes_invalid=0 send_seq=16179 receive_seq=16179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997653 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38911 bytes_read=1591778 bytes_retransmit=9 bytes_invalid=0 send_seq=6426 receive_seq=6426 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997747 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39397 bytes_read=118626 bytes_retransmit=9 bytes_invalid=0 send_seq=6413 receive_seq=6413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999466 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93489 bytes_read=2446074 bytes_retransmit=0 bytes_invalid=0 send_seq=10972 receive_seq=10972 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998740 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=55.6 th1: temp=55.0 th2: temp=61.4 th3: temp=59.0 sysload=0.08 cputime=462.870 memavail=7395528 print_time=6259.860 buffer_time=2.076 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 27 Hz
Stats 6236.1: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28514519 bytes_read=4473235 bytes_retransmit=9 bytes_invalid=0 send_seq=539623 receive_seq=539623 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=0 freq=400015901 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38650 bytes_read=121025 bytes_retransmit=0 bytes_invalid=0 send_seq=6413 receive_seq=6413 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999475 adj=49997830 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191782 bytes_read=6120028 bytes_retransmit=9 bytes_invalid=0 send_seq=26667 receive_seq=26667 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997720 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=117756 bytes_read=2987285 bytes_retransmit=9 bytes_invalid=0 send_seq=16190 receive_seq=16190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997603 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38917 bytes_read=1592012 bytes_retransmit=9 bytes_invalid=0 send_seq=6427 receive_seq=6427 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997722 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39403 bytes_read=118642 bytes_retransmit=9 bytes_invalid=0 send_seq=6414 receive_seq=6414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93495 bytes_read=2446430 bytes_retransmit=0 bytes_invalid=0 send_seq=10973 receive_seq=10973 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998732 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=55.8 th1: temp=55.1 th2: temp=61.4 th3: temp=59.0 sysload=0.08 cputime=462.960 memavail=7395528 print_time=6261.088 buffer_time=2.302 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 28 Hz
Stats 6237.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28517729 bytes_read=4473932 bytes_retransmit=9 bytes_invalid=0 send_seq=539692 receive_seq=539692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=400015893 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38656 bytes_read=121041 bytes_retransmit=0 bytes_invalid=0 send_seq=6414 receive_seq=6414 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999479 adj=49997799 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191788 bytes_read=6120128 bytes_retransmit=9 bytes_invalid=0 send_seq=26668 receive_seq=26668 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997735 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=117832 bytes_read=2990341 bytes_retransmit=9 bytes_invalid=0 send_seq=16201 receive_seq=16201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997595 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38923 bytes_read=1592246 bytes_retransmit=9 bytes_invalid=0 send_seq=6428 receive_seq=6428 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997723 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39409 bytes_read=118669 bytes_retransmit=9 bytes_invalid=0 send_seq=6415 receive_seq=6415 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93501 bytes_read=2446786 bytes_retransmit=0 bytes_invalid=0 send_seq=10974 receive_seq=10974 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998726 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=55.8 th1: temp=55.0 th2: temp=61.4 th3: temp=59.0 sysload=0.08 cputime=463.052 memavail=7387508 print_time=6261.945 buffer_time=2.159 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 29 Hz
Stats 6238.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28521452 bytes_read=4474629 bytes_retransmit=9 bytes_invalid=0 send_seq=539770 receive_seq=539770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=0 freq=400015897 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38662 bytes_read=121057 bytes_retransmit=0 bytes_invalid=0 send_seq=6415 receive_seq=6415 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999483 adj=49997836 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191794 bytes_read=6120270 bytes_retransmit=9 bytes_invalid=0 send_seq=26669 receive_seq=26669 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997724 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=117908 bytes_read=2993443 bytes_retransmit=9 bytes_invalid=0 send_seq=16212 receive_seq=16212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38929 bytes_read=1592540 bytes_retransmit=9 bytes_invalid=0 send_seq=6429 receive_seq=6429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997725 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39415 bytes_read=118685 bytes_retransmit=9 bytes_invalid=0 send_seq=6416 receive_seq=6416 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93507 bytes_read=2447142 bytes_retransmit=0 bytes_invalid=0 send_seq=10975 receive_seq=10975 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998721 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=55.8 th1: temp=54.8 th2: temp=61.6 th3: temp=59.0 sysload=0.08 cputime=463.139 memavail=7393892 print_time=6262.914 buffer_time=2.128 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 30 Hz
Stats 6239.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28525838 bytes_read=4475379 bytes_retransmit=9 bytes_invalid=0 send_seq=539858 receive_seq=539858 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015880 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38668 bytes_read=121073 bytes_retransmit=0 bytes_invalid=0 send_seq=6416 receive_seq=6416 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999487 adj=49997823 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191800 bytes_read=6120370 bytes_retransmit=9 bytes_invalid=0 send_seq=26670 receive_seq=26670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997689 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=117984 bytes_read=2996501 bytes_retransmit=9 bytes_invalid=0 send_seq=16223 receive_seq=16223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38935 bytes_read=1592789 bytes_retransmit=9 bytes_invalid=0 send_seq=6430 receive_seq=6430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39421 bytes_read=118701 bytes_retransmit=9 bytes_invalid=0 send_seq=6417 receive_seq=6417 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93513 bytes_read=2447498 bytes_retransmit=0 bytes_invalid=0 send_seq=10976 receive_seq=10976 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998713 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=55.8 th1: temp=55.2 th2: temp=61.6 th3: temp=59.1 sysload=0.08 cputime=463.229 memavail=7393892 print_time=6264.101 buffer_time=2.313 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 31 Hz
Stats 6240.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28529213 bytes_read=4476078 bytes_retransmit=9 bytes_invalid=0 send_seq=539930 receive_seq=539930 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=36 upcoming_bytes=0 freq=400015875 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38674 bytes_read=121102 bytes_retransmit=0 bytes_invalid=0 send_seq=6417 receive_seq=6417 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999491 adj=49997797 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191806 bytes_read=6120470 bytes_retransmit=9 bytes_invalid=0 send_seq=26671 receive_seq=26671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997704 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=118060 bytes_read=2999557 bytes_retransmit=9 bytes_invalid=0 send_seq=16234 receive_seq=16234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997629 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38941 bytes_read=1593007 bytes_retransmit=9 bytes_invalid=0 send_seq=6431 receive_seq=6431 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997700 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39427 bytes_read=118717 bytes_retransmit=9 bytes_invalid=0 send_seq=6418 receive_seq=6418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93519 bytes_read=2447854 bytes_retransmit=0 bytes_invalid=0 send_seq=10977 receive_seq=10977 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998707 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=55.4 th1: temp=55.0 th2: temp=61.6 th3: temp=59.2 sysload=0.07 cputime=463.314 memavail=7393892 print_time=6264.988 buffer_time=2.199 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 32 Hz
Stats 6241.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28533126 bytes_read=4476788 bytes_retransmit=9 bytes_invalid=0 send_seq=540010 receive_seq=540010 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015857 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38680 bytes_read=121118 bytes_retransmit=0 bytes_invalid=0 send_seq=6418 receive_seq=6418 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999496 adj=49997826 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191812 bytes_read=6120598 bytes_retransmit=9 bytes_invalid=0 send_seq=26672 receive_seq=26672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997705 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=118136 bytes_read=3002701 bytes_retransmit=9 bytes_invalid=0 send_seq=16245 receive_seq=16245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997604 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38947 bytes_read=1593280 bytes_retransmit=9 bytes_invalid=0 send_seq=6432 receive_seq=6432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997698 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39433 bytes_read=118733 bytes_retransmit=9 bytes_invalid=0 send_seq=6419 receive_seq=6419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93525 bytes_read=2448210 bytes_retransmit=0 bytes_invalid=0 send_seq=10978 receive_seq=10978 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998705 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=55.5 th1: temp=55.1 th2: temp=61.6 th3: temp=59.2 sysload=0.07 cputime=463.402 memavail=7393892 print_time=6265.935 buffer_time=2.146 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 33 Hz
Stats 6242.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28536406 bytes_read=4477464 bytes_retransmit=9 bytes_invalid=0 send_seq=540080 receive_seq=540080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=0 freq=400015841 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38686 bytes_read=121134 bytes_retransmit=0 bytes_invalid=0 send_seq=6419 receive_seq=6419 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999499 adj=49997857 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191818 bytes_read=6120698 bytes_retransmit=9 bytes_invalid=0 send_seq=26673 receive_seq=26673 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997720 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=118212 bytes_read=3005760 bytes_retransmit=9 bytes_invalid=0 send_seq=16256 receive_seq=16256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997605 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38953 bytes_read=1593498 bytes_retransmit=9 bytes_invalid=0 send_seq=6433 receive_seq=6433 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997710 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39439 bytes_read=118760 bytes_retransmit=9 bytes_invalid=0 send_seq=6420 receive_seq=6420 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93531 bytes_read=2448566 bytes_retransmit=0 bytes_invalid=0 send_seq=10979 receive_seq=10979 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998710 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=55.8 th1: temp=54.9 th2: temp=61.6 th3: temp=59.2 sysload=0.07 cputime=463.489 memavail=7393892 print_time=6266.810 buffer_time=2.020 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 34 Hz
Stats 6243.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28541249 bytes_read=4478278 bytes_retransmit=9 bytes_invalid=0 send_seq=540175 receive_seq=540175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015828 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38692 bytes_read=121150 bytes_retransmit=0 bytes_invalid=0 send_seq=6420 receive_seq=6420 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999504 adj=49997884 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191824 bytes_read=6120812 bytes_retransmit=9 bytes_invalid=0 send_seq=26674 receive_seq=26674 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997842 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=118288 bytes_read=3008835 bytes_retransmit=9 bytes_invalid=0 send_seq=16267 receive_seq=16267 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997606 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=38959 bytes_read=1593716 bytes_retransmit=9 bytes_invalid=0 send_seq=6434 receive_seq=6434 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997723 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39445 bytes_read=118776 bytes_retransmit=9 bytes_invalid=0 send_seq=6421 receive_seq=6421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93537 bytes_read=2448922 bytes_retransmit=0 bytes_invalid=0 send_seq=10980 receive_seq=10980 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998709 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=55.8 th1: temp=55.0 th2: temp=61.9 th3: temp=59.0 sysload=0.07 cputime=463.582 memavail=7393892 print_time=6268.022 buffer_time=2.232 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 35 Hz
Stats 6244.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28545629 bytes_read=4479028 bytes_retransmit=9 bytes_invalid=0 send_seq=540263 receive_seq=540263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015814 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38698 bytes_read=121166 bytes_retransmit=0 bytes_invalid=0 send_seq=6421 receive_seq=6421 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999507 adj=49997849 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191830 bytes_read=6120940 bytes_retransmit=9 bytes_invalid=0 send_seq=26675 receive_seq=26675 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997799 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=118364 bytes_read=3011920 bytes_retransmit=9 bytes_invalid=0 send_seq=16278 receive_seq=16278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997594 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=38965 bytes_read=1594005 bytes_retransmit=9 bytes_invalid=0 send_seq=6435 receive_seq=6435 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997717 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39451 bytes_read=118792 bytes_retransmit=9 bytes_invalid=0 send_seq=6422 receive_seq=6422 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999462 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93543 bytes_read=2449278 bytes_retransmit=0 bytes_invalid=0 send_seq=10981 receive_seq=10981 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998699 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=55.6 th1: temp=55.1 th2: temp=61.7 th3: temp=59.3 sysload=0.07 cputime=463.670 memavail=7393892 print_time=6268.973 buffer_time=2.183 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 36 Hz
Stats 6245.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28548930 bytes_read=4479683 bytes_retransmit=9 bytes_invalid=0 send_seq=540332 receive_seq=540332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015803 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38704 bytes_read=121195 bytes_retransmit=0 bytes_invalid=0 send_seq=6422 receive_seq=6422 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999509 adj=49997858 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191836 bytes_read=6121040 bytes_retransmit=9 bytes_invalid=0 send_seq=26676 receive_seq=26676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997805 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=118440 bytes_read=3014978 bytes_retransmit=9 bytes_invalid=0 send_seq=16289 receive_seq=16289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997687 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=38971 bytes_read=1594231 bytes_retransmit=9 bytes_invalid=0 send_seq=6436 receive_seq=6436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997762 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39457 bytes_read=118808 bytes_retransmit=9 bytes_invalid=0 send_seq=6423 receive_seq=6423 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93549 bytes_read=2449634 bytes_retransmit=0 bytes_invalid=0 send_seq=10982 receive_seq=10982 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998701 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=55.7 th1: temp=54.9 th2: temp=61.7 th3: temp=59.2 sysload=0.06 cputime=463.760 memavail=7393892 print_time=6269.837 buffer_time=2.047 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 37 Hz
Stats 6246.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28553373 bytes_read=4480467 bytes_retransmit=9 bytes_invalid=0 send_seq=540421 receive_seq=540421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015787 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38710 bytes_read=121211 bytes_retransmit=0 bytes_invalid=0 send_seq=6423 receive_seq=6423 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999512 adj=49997876 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191842 bytes_read=6121154 bytes_retransmit=9 bytes_invalid=0 send_seq=26677 receive_seq=26677 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997797 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=118509 bytes_read=3018013 bytes_retransmit=9 bytes_invalid=0 send_seq=16299 receive_seq=16299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997666 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=38977 bytes_read=1594465 bytes_retransmit=9 bytes_invalid=0 send_seq=6437 receive_seq=6437 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997795 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39463 bytes_read=118824 bytes_retransmit=9 bytes_invalid=0 send_seq=6424 receive_seq=6424 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999470 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93555 bytes_read=2449990 bytes_retransmit=0 bytes_invalid=0 send_seq=10983 receive_seq=10983 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999949 adj=31998803 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=55.7 th1: temp=55.0 th2: temp=61.9 th3: temp=59.3 sysload=0.06 cputime=463.848 memavail=7393892 print_time=6270.782 buffer_time=1.991 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 38 Hz
Stats 6247.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28558366 bytes_read=4481278 bytes_retransmit=9 bytes_invalid=0 send_seq=540518 receive_seq=540518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=235 freq=400015773 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38716 bytes_read=121227 bytes_retransmit=0 bytes_invalid=0 send_seq=6424 receive_seq=6424 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999515 adj=49997887 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191848 bytes_read=6121268 bytes_retransmit=9 bytes_invalid=0 send_seq=26678 receive_seq=26678 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997795 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=118585 bytes_read=3021098 bytes_retransmit=9 bytes_invalid=0 send_seq=16310 receive_seq=16310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997654 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=38983 bytes_read=1594759 bytes_retransmit=9 bytes_invalid=0 send_seq=6438 receive_seq=6438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997790 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39469 bytes_read=118851 bytes_retransmit=9 bytes_invalid=0 send_seq=6425 receive_seq=6425 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999470 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93561 bytes_read=2450346 bytes_retransmit=0 bytes_invalid=0 send_seq=10984 receive_seq=10984 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999948 adj=31998879 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=56.4 th1: temp=55.1 th2: temp=62.0 th3: temp=59.4 sysload=0.06 cputime=463.945 memavail=7393416 print_time=6271.979 buffer_time=2.187 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 39 Hz
Stats 6248.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28562058 bytes_read=4481964 bytes_retransmit=9 bytes_invalid=0 send_seq=540594 receive_seq=540594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015760 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38722 bytes_read=121243 bytes_retransmit=0 bytes_invalid=0 send_seq=6425 receive_seq=6425 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999519 adj=49997836 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191854 bytes_read=6121382 bytes_retransmit=9 bytes_invalid=0 send_seq=26679 receive_seq=26679 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997784 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=118661 bytes_read=3024172 bytes_retransmit=9 bytes_invalid=0 send_seq=16321 receive_seq=16321 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997640 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=38989 bytes_read=1594993 bytes_retransmit=9 bytes_invalid=0 send_seq=6439 receive_seq=6439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997764 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39475 bytes_read=118867 bytes_retransmit=9 bytes_invalid=0 send_seq=6426 receive_seq=6426 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999467 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93567 bytes_read=2450702 bytes_retransmit=0 bytes_invalid=0 send_seq=10985 receive_seq=10985 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998816 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=55.9 th1: temp=55.1 th2: temp=61.8 th3: temp=59.4 sysload=0.06 cputime=464.037 memavail=7393420 print_time=6272.860 buffer_time=2.068 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 40 Hz
Stats 6249.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28566666 bytes_read=4482756 bytes_retransmit=9 bytes_invalid=0 send_seq=540685 receive_seq=540685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=36 upcoming_bytes=0 freq=400015759 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38728 bytes_read=121259 bytes_retransmit=0 bytes_invalid=0 send_seq=6426 receive_seq=6426 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999523 adj=49997865 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191860 bytes_read=6121496 bytes_retransmit=9 bytes_invalid=0 send_seq=26680 receive_seq=26680 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997800 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=118737 bytes_read=3027286 bytes_retransmit=9 bytes_invalid=0 send_seq=16332 receive_seq=16332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997635 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=38995 bytes_read=1595242 bytes_retransmit=9 bytes_invalid=0 send_seq=6440 receive_seq=6440 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997775 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39481 bytes_read=118883 bytes_retransmit=9 bytes_invalid=0 send_seq=6427 receive_seq=6427 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999468 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93573 bytes_read=2451058 bytes_retransmit=0 bytes_invalid=0 send_seq=10986 receive_seq=10986 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998796 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=55.6 th1: temp=55.0 th2: temp=61.8 th3: temp=59.5 sysload=0.06 cputime=464.131 memavail=7393420 print_time=6273.808 buffer_time=2.016 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 41 Hz
Stats 6250.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28571356 bytes_read=4483501 bytes_retransmit=9 bytes_invalid=0 send_seq=540772 receive_seq=540772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=724 freq=400015759 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38734 bytes_read=121288 bytes_retransmit=0 bytes_invalid=0 send_seq=6427 receive_seq=6427 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999527 adj=49997875 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191866 bytes_read=6121610 bytes_retransmit=9 bytes_invalid=0 send_seq=26681 receive_seq=26681 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997782 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=118813 bytes_read=3030370 bytes_retransmit=9 bytes_invalid=0 send_seq=16343 receive_seq=16343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997613 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39001 bytes_read=1595536 bytes_retransmit=9 bytes_invalid=0 send_seq=6441 receive_seq=6441 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997750 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39487 bytes_read=118899 bytes_retransmit=9 bytes_invalid=0 send_seq=6428 receive_seq=6428 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93579 bytes_read=2451414 bytes_retransmit=0 bytes_invalid=0 send_seq=10987 receive_seq=10987 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998759 coil_temp=17.0 refs=0 mcu_temp=20.27 supply_voltage=3.012 th0: temp=55.7 th1: temp=55.1 th2: temp=61.7 th3: temp=59.4 sysload=0.06 cputime=464.234 memavail=7393420 print_time=6275.015 buffer_time=2.222 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 42 Hz
Stats 6251.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28575860 bytes_read=4484256 bytes_retransmit=9 bytes_invalid=0 send_seq=540861 receive_seq=540861 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=0 freq=400015758 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38740 bytes_read=121304 bytes_retransmit=0 bytes_invalid=0 send_seq=6428 receive_seq=6428 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999529 adj=49997817 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191872 bytes_read=6121710 bytes_retransmit=9 bytes_invalid=0 send_seq=26682 receive_seq=26682 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997743 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=118889 bytes_read=3033427 bytes_retransmit=9 bytes_invalid=0 send_seq=16354 receive_seq=16354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997571 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39007 bytes_read=1595770 bytes_retransmit=9 bytes_invalid=0 send_seq=6442 receive_seq=6442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997725 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39493 bytes_read=118915 bytes_retransmit=9 bytes_invalid=0 send_seq=6429 receive_seq=6429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93585 bytes_read=2451770 bytes_retransmit=0 bytes_invalid=0 send_seq=10988 receive_seq=10988 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998718 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=55.8 th1: temp=55.2 th2: temp=61.9 th3: temp=59.4 sysload=0.06 cputime=464.331 memavail=7393420 print_time=6275.903 buffer_time=2.110 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 43 Hz
Stats 6252.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28580388 bytes_read=4485051 bytes_retransmit=9 bytes_invalid=0 send_seq=540949 receive_seq=540949 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=343 freq=400015756 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38746 bytes_read=121320 bytes_retransmit=0 bytes_invalid=0 send_seq=6429 receive_seq=6429 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999532 adj=49997825 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191878 bytes_read=6121824 bytes_retransmit=9 bytes_invalid=0 send_seq=26683 receive_seq=26683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997819 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=118965 bytes_read=3036484 bytes_retransmit=9 bytes_invalid=0 send_seq=16365 receive_seq=16365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997550 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39013 bytes_read=1596004 bytes_retransmit=9 bytes_invalid=0 send_seq=6443 receive_seq=6443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997712 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39499 bytes_read=118942 bytes_retransmit=9 bytes_invalid=0 send_seq=6430 receive_seq=6430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93591 bytes_read=2452126 bytes_retransmit=0 bytes_invalid=0 send_seq=10989 receive_seq=10989 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998701 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=55.7 th1: temp=55.4 th2: temp=61.9 th3: temp=59.4 sysload=0.06 cputime=464.430 memavail=7393468 print_time=6276.814 buffer_time=2.020 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 44 Hz
Stats 6253.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28585072 bytes_read=4485811 bytes_retransmit=9 bytes_invalid=0 send_seq=541039 receive_seq=541039 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=46 upcoming_bytes=1170 freq=400015775 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38752 bytes_read=121336 bytes_retransmit=0 bytes_invalid=0 send_seq=6430 receive_seq=6430 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999535 adj=49997829 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191884 bytes_read=6121952 bytes_retransmit=9 bytes_invalid=0 send_seq=26684 receive_seq=26684 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997785 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=119041 bytes_read=3039586 bytes_retransmit=9 bytes_invalid=0 send_seq=16376 receive_seq=16376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997536 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39019 bytes_read=1596298 bytes_retransmit=9 bytes_invalid=0 send_seq=6444 receive_seq=6444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997703 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39505 bytes_read=118958 bytes_retransmit=9 bytes_invalid=0 send_seq=6431 receive_seq=6431 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.8 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93597 bytes_read=2452482 bytes_retransmit=0 bytes_invalid=0 send_seq=10990 receive_seq=10990 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998689 coil_temp=16.9 refs=0 mcu_temp=20.25 supply_voltage=3.012 th0: temp=55.6 th1: temp=55.2 th2: temp=61.9 th3: temp=59.6 sysload=0.06 cputime=464.537 memavail=7393468 print_time=6278.017 buffer_time=2.223 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 45 Hz
Stats 6254.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28590170 bytes_read=4486596 bytes_retransmit=9 bytes_invalid=0 send_seq=541134 receive_seq=541134 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=53 freq=400015815 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38758 bytes_read=121352 bytes_retransmit=0 bytes_invalid=0 send_seq=6431 receive_seq=6431 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999537 adj=49997755 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191890 bytes_read=6122052 bytes_retransmit=9 bytes_invalid=0 send_seq=26685 receive_seq=26685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997717 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=119117 bytes_read=3042644 bytes_retransmit=9 bytes_invalid=0 send_seq=16387 receive_seq=16387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997484 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39025 bytes_read=1596547 bytes_retransmit=9 bytes_invalid=0 send_seq=6445 receive_seq=6445 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39511 bytes_read=118974 bytes_retransmit=9 bytes_invalid=0 send_seq=6432 receive_seq=6432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93603 bytes_read=2452838 bytes_retransmit=0 bytes_invalid=0 send_seq=10991 receive_seq=10991 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998655 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.2 th2: temp=62.0 th3: temp=59.5 sysload=0.06 cputime=464.648 memavail=7386196 print_time=6278.918 buffer_time=2.124 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 46 Hz
Stats 6255.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28594552 bytes_read=4487360 bytes_retransmit=9 bytes_invalid=0 send_seq=541219 receive_seq=541219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=687 freq=400015818 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38764 bytes_read=121381 bytes_retransmit=0 bytes_invalid=0 send_seq=6432 receive_seq=6432 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999545 adj=49997693 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191896 bytes_read=6122166 bytes_retransmit=9 bytes_invalid=0 send_seq=26686 receive_seq=26686 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997639 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=119193 bytes_read=3045701 bytes_retransmit=9 bytes_invalid=0 send_seq=16398 receive_seq=16398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997415 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39031 bytes_read=1596781 bytes_retransmit=9 bytes_invalid=0 send_seq=6446 receive_seq=6446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997596 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39517 bytes_read=118990 bytes_retransmit=9 bytes_invalid=0 send_seq=6433 receive_seq=6433 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93609 bytes_read=2453194 bytes_retransmit=0 bytes_invalid=0 send_seq=10992 receive_seq=10992 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998603 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=55.6 th1: temp=55.2 th2: temp=62.0 th3: temp=59.5 sysload=0.05 cputime=464.751 memavail=7393584 print_time=6279.840 buffer_time=2.045 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 47 Hz
Stats 6256.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=28599379 bytes_read=4488105 bytes_retransmit=9 bytes_invalid=0 send_seq=541306 receive_seq=541306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=22 upcoming_bytes=1484 freq=400015818 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38770 bytes_read=121397 bytes_retransmit=0 bytes_invalid=0 send_seq=6433 receive_seq=6433 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999554 adj=49997771 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191902 bytes_read=6122280 bytes_retransmit=9 bytes_invalid=0 send_seq=26687 receive_seq=26687 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997628 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=119269 bytes_read=3048844 bytes_retransmit=9 bytes_invalid=0 send_seq=16409 receive_seq=16409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997428 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39037 bytes_read=1597075 bytes_retransmit=9 bytes_invalid=0 send_seq=6447 receive_seq=6447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997612 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39523 bytes_read=119006 bytes_retransmit=9 bytes_invalid=0 send_seq=6434 receive_seq=6434 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93615 bytes_read=2453550 bytes_retransmit=0 bytes_invalid=0 send_seq=10993 receive_seq=10993 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998603 coil_temp=16.9 refs=0 mcu_temp=20.25 supply_voltage=3.012 th0: temp=55.7 th1: temp=55.1 th2: temp=62.1 th3: temp=59.5 sysload=0.05 cputime=464.858 memavail=7393584 print_time=6281.051 buffer_time=2.255 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 48 Hz
Stats 6257.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=28604602 bytes_read=4488926 bytes_retransmit=9 bytes_invalid=0 send_seq=541405 receive_seq=541405 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=237 freq=400015800 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38776 bytes_read=121413 bytes_retransmit=0 bytes_invalid=0 send_seq=6434 receive_seq=6434 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999556 adj=49997811 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191908 bytes_read=6122380 bytes_retransmit=9 bytes_invalid=0 send_seq=26688 receive_seq=26688 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997639 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=119345 bytes_read=3051900 bytes_retransmit=9 bytes_invalid=0 send_seq=16420 receive_seq=16420 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997448 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39043 bytes_read=1597309 bytes_retransmit=9 bytes_invalid=0 send_seq=6448 receive_seq=6448 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39529 bytes_read=119033 bytes_retransmit=9 bytes_invalid=0 send_seq=6435 receive_seq=6435 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93621 bytes_read=2453906 bytes_retransmit=0 bytes_invalid=0 send_seq=10994 receive_seq=10994 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998616 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=55.7 th1: temp=54.9 th2: temp=61.9 th3: temp=59.5 sysload=0.05 cputime=464.960 memavail=7395660 print_time=6281.937 buffer_time=2.140 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 49 Hz
Stats 6258.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=28609110 bytes_read=4489700 bytes_retransmit=9 bytes_invalid=0 send_seq=541492 receive_seq=541492 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=43 upcoming_bytes=862 freq=400015792 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38782 bytes_read=121429 bytes_retransmit=0 bytes_invalid=0 send_seq=6435 receive_seq=6435 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999558 adj=49997840 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191914 bytes_read=6122508 bytes_retransmit=9 bytes_invalid=0 send_seq=26689 receive_seq=26689 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997666 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=119421 bytes_read=3054975 bytes_retransmit=9 bytes_invalid=0 send_seq=16431 receive_seq=16431 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997481 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39049 bytes_read=1597543 bytes_retransmit=9 bytes_invalid=0 send_seq=6449 receive_seq=6449 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39535 bytes_read=119049 bytes_retransmit=9 bytes_invalid=0 send_seq=6436 receive_seq=6436 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999466 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93627 bytes_read=2454262 bytes_retransmit=0 bytes_invalid=0 send_seq=10995 receive_seq=10995 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998627 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=55.9 th1: temp=55.1 th2: temp=62.1 th3: temp=59.6 sysload=0.05 cputime=465.058 memavail=7395788 print_time=6282.858 buffer_time=2.060 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 50 Hz
Stats 6259.1: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=28613931 bytes_read=4490466 bytes_retransmit=9 bytes_invalid=0 send_seq=541584 receive_seq=541584 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=1953 freq=400015787 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38788 bytes_read=121445 bytes_retransmit=0 bytes_invalid=0 send_seq=6436 receive_seq=6436 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999559 adj=49997838 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191920 bytes_read=6122622 bytes_retransmit=9 bytes_invalid=0 send_seq=26690 receive_seq=26690 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997670 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=119497 bytes_read=3058061 bytes_retransmit=9 bytes_invalid=0 send_seq=16442 receive_seq=16442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997501 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39055 bytes_read=1597852 bytes_retransmit=9 bytes_invalid=0 send_seq=6450 receive_seq=6450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39541 bytes_read=119065 bytes_retransmit=9 bytes_invalid=0 send_seq=6437 receive_seq=6437 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93633 bytes_read=2454618 bytes_retransmit=0 bytes_invalid=0 send_seq=10996 receive_seq=10996 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998629 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.012 th0: temp=55.6 th1: temp=55.1 th2: temp=62.0 th3: temp=59.5 sysload=0.05 cputime=465.167 memavail=7395788 print_time=6284.061 buffer_time=2.263 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 51 Hz
Stats 6260.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=28619370 bytes_read=4491291 bytes_retransmit=9 bytes_invalid=0 send_seq=541687 receive_seq=541687 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=588 freq=400015778 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38794 bytes_read=121474 bytes_retransmit=0 bytes_invalid=0 send_seq=6437 receive_seq=6437 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999562 adj=49997790 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191926 bytes_read=6122722 bytes_retransmit=9 bytes_invalid=0 send_seq=26691 receive_seq=26691 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997678 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=119573 bytes_read=3061119 bytes_retransmit=9 bytes_invalid=0 send_seq=16453 receive_seq=16453 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997513 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39061 bytes_read=1598086 bytes_retransmit=9 bytes_invalid=0 send_seq=6451 receive_seq=6451 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39547 bytes_read=119081 bytes_retransmit=9 bytes_invalid=0 send_seq=6438 receive_seq=6438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93639 bytes_read=2454974 bytes_retransmit=0 bytes_invalid=0 send_seq=10997 receive_seq=10997 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998641 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=56.0 th1: temp=55.2 th2: temp=61.9 th3: temp=59.5 sysload=0.05 cputime=465.268 memavail=7395536 print_time=6284.953 buffer_time=2.154 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 52 Hz
Stats 6261.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=28624076 bytes_read=4492080 bytes_retransmit=9 bytes_invalid=0 send_seq=541777 receive_seq=541777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=1114 freq=400015768 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38800 bytes_read=121490 bytes_retransmit=0 bytes_invalid=0 send_seq=6438 receive_seq=6438 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999563 adj=49997813 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191932 bytes_read=6122836 bytes_retransmit=9 bytes_invalid=0 send_seq=26692 receive_seq=26692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997706 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=119649 bytes_read=3064175 bytes_retransmit=9 bytes_invalid=0 send_seq=16464 receive_seq=16464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39067 bytes_read=1598320 bytes_retransmit=9 bytes_invalid=0 send_seq=6452 receive_seq=6452 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39553 bytes_read=119097 bytes_retransmit=9 bytes_invalid=0 send_seq=6439 receive_seq=6439 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93645 bytes_read=2455330 bytes_retransmit=0 bytes_invalid=0 send_seq=10998 receive_seq=10998 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998655 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=56.0 th1: temp=55.1 th2: temp=62.0 th3: temp=59.6 sysload=0.05 cputime=465.367 memavail=7395536 print_time=6285.869 buffer_time=2.068 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 53 Hz
Stats 6262.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28629093 bytes_read=4492876 bytes_retransmit=9 bytes_invalid=0 send_seq=541871 receive_seq=541871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=2180 freq=400015766 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38806 bytes_read=121506 bytes_retransmit=0 bytes_invalid=0 send_seq=6439 receive_seq=6439 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999565 adj=49997808 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191938 bytes_read=6122950 bytes_retransmit=9 bytes_invalid=0 send_seq=26693 receive_seq=26693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997710 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=119725 bytes_read=3067260 bytes_retransmit=9 bytes_invalid=0 send_seq=16475 receive_seq=16475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997533 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39073 bytes_read=1598614 bytes_retransmit=9 bytes_invalid=0 send_seq=6453 receive_seq=6453 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39559 bytes_read=119124 bytes_retransmit=9 bytes_invalid=0 send_seq=6440 receive_seq=6440 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93651 bytes_read=2455686 bytes_retransmit=0 bytes_invalid=0 send_seq=10999 receive_seq=10999 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998660 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=55.9 th1: temp=55.0 th2: temp=62.0 th3: temp=59.5 sysload=0.05 cputime=465.477 memavail=7395536 print_time=6287.069 buffer_time=2.269 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 54 Hz
Stats 6263.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28634622 bytes_read=4493706 bytes_retransmit=9 bytes_invalid=0 send_seq=541975 receive_seq=541975 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=926 freq=400015783 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38812 bytes_read=121522 bytes_retransmit=0 bytes_invalid=0 send_seq=6440 receive_seq=6440 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999566 adj=49997768 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191944 bytes_read=6123064 bytes_retransmit=9 bytes_invalid=0 send_seq=26694 receive_seq=26694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997702 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=119794 bytes_read=3070368 bytes_retransmit=9 bytes_invalid=0 send_seq=16485 receive_seq=16485 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39079 bytes_read=1598848 bytes_retransmit=9 bytes_invalid=0 send_seq=6454 receive_seq=6454 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39565 bytes_read=119140 bytes_retransmit=9 bytes_invalid=0 send_seq=6441 receive_seq=6441 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93657 bytes_read=2456042 bytes_retransmit=0 bytes_invalid=0 send_seq=11000 receive_seq=11000 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998654 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=55.7 th1: temp=55.2 th2: temp=62.1 th3: temp=59.6 sysload=0.05 cputime=465.579 memavail=7395536 print_time=6287.972 buffer_time=2.171 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 55 Hz
Stats 6264.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28639404 bytes_read=4494485 bytes_retransmit=9 bytes_invalid=0 send_seq=542063 receive_seq=542063 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=1376 freq=400015781 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38818 bytes_read=121538 bytes_retransmit=0 bytes_invalid=0 send_seq=6441 receive_seq=6441 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999568 adj=49997741 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191950 bytes_read=6123178 bytes_retransmit=9 bytes_invalid=0 send_seq=26695 receive_seq=26695 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997655 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=119870 bytes_read=3073424 bytes_retransmit=9 bytes_invalid=0 send_seq=16496 receive_seq=16496 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39085 bytes_read=1599097 bytes_retransmit=9 bytes_invalid=0 send_seq=6455 receive_seq=6455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39571 bytes_read=119156 bytes_retransmit=9 bytes_invalid=0 send_seq=6442 receive_seq=6442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93663 bytes_read=2456398 bytes_retransmit=0 bytes_invalid=0 send_seq=11001 receive_seq=11001 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998628 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=55.8 th1: temp=55.1 th2: temp=62.2 th3: temp=59.6 sysload=0.05 cputime=465.680 memavail=7395536 print_time=6288.874 buffer_time=2.071 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 56 Hz
Stats 6265.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28644575 bytes_read=4495265 bytes_retransmit=9 bytes_invalid=0 send_seq=542157 receive_seq=542157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=29 upcoming_bytes=610 freq=400015787 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38824 bytes_read=121567 bytes_retransmit=0 bytes_invalid=0 send_seq=6442 receive_seq=6442 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999570 adj=49997751 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191956 bytes_read=6123292 bytes_retransmit=9 bytes_invalid=0 send_seq=26696 receive_seq=26696 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997656 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=119946 bytes_read=3076510 bytes_retransmit=9 bytes_invalid=0 send_seq=16507 receive_seq=16507 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997478 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39091 bytes_read=1599391 bytes_retransmit=9 bytes_invalid=0 send_seq=6456 receive_seq=6456 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39577 bytes_read=119172 bytes_retransmit=9 bytes_invalid=0 send_seq=6443 receive_seq=6443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93669 bytes_read=2456753 bytes_retransmit=0 bytes_invalid=0 send_seq=11002 receive_seq=11002 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998633 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=55.9 th1: temp=55.2 th2: temp=62.1 th3: temp=59.6 sysload=0.05 cputime=465.785 memavail=7395536 print_time=6289.792 buffer_time=1.989 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 57 Hz
Stats 6266.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28650205 bytes_read=4496095 bytes_retransmit=9 bytes_invalid=0 send_seq=542261 receive_seq=542261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=1325 freq=400015788 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38830 bytes_read=121583 bytes_retransmit=0 bytes_invalid=0 send_seq=6443 receive_seq=6443 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999571 adj=49997738 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191962 bytes_read=6123392 bytes_retransmit=9 bytes_invalid=0 send_seq=26697 receive_seq=26697 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997640 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=120022 bytes_read=3079566 bytes_retransmit=9 bytes_invalid=0 send_seq=16518 receive_seq=16518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997462 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39097 bytes_read=1599625 bytes_retransmit=9 bytes_invalid=0 send_seq=6457 receive_seq=6457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39583 bytes_read=119188 bytes_retransmit=9 bytes_invalid=0 send_seq=6444 receive_seq=6444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93675 bytes_read=2457098 bytes_retransmit=0 bytes_invalid=0 send_seq=11003 receive_seq=11003 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998627 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=55.9 th1: temp=55.2 th2: temp=62.0 th3: temp=59.6 sysload=0.05 cputime=465.896 memavail=7395536 print_time=6290.998 buffer_time=2.195 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 58 Hz
Stats 6267.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=28655186 bytes_read=4496920 bytes_retransmit=9 bytes_invalid=0 send_seq=542355 receive_seq=542355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=1806 freq=400015797 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38836 bytes_read=121599 bytes_retransmit=0 bytes_invalid=0 send_seq=6444 receive_seq=6444 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999573 adj=49997711 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191968 bytes_read=6123506 bytes_retransmit=9 bytes_invalid=0 send_seq=26698 receive_seq=26698 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997642 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=120098 bytes_read=3082624 bytes_retransmit=9 bytes_invalid=0 send_seq=16529 receive_seq=16529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997472 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39103 bytes_read=1599859 bytes_retransmit=9 bytes_invalid=0 send_seq=6458 receive_seq=6458 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39589 bytes_read=119215 bytes_retransmit=9 bytes_invalid=0 send_seq=6445 receive_seq=6445 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93681 bytes_read=2457443 bytes_retransmit=0 bytes_invalid=0 send_seq=11004 receive_seq=11004 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998644 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=55.9 th1: temp=55.0 th2: temp=62.2 th3: temp=59.5 sysload=0.05 cputime=465.998 memavail=7394556 print_time=6291.896 buffer_time=2.091 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 59 Hz
Stats 6268.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=28660527 bytes_read=4497730 bytes_retransmit=9 bytes_invalid=0 send_seq=542455 receive_seq=542455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=23 upcoming_bytes=994 freq=400015811 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38842 bytes_read=121615 bytes_retransmit=0 bytes_invalid=0 send_seq=6445 receive_seq=6445 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999574 adj=49997711 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191974 bytes_read=6123634 bytes_retransmit=9 bytes_invalid=0 send_seq=26699 receive_seq=26699 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997639 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=120174 bytes_read=3085727 bytes_retransmit=9 bytes_invalid=0 send_seq=16540 receive_seq=16540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997459 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39109 bytes_read=1600153 bytes_retransmit=9 bytes_invalid=0 send_seq=6459 receive_seq=6459 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997623 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39595 bytes_read=119231 bytes_retransmit=9 bytes_invalid=0 send_seq=6446 receive_seq=6446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93687 bytes_read=2457788 bytes_retransmit=0 bytes_invalid=0 send_seq=11005 receive_seq=11005 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998635 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=55.9 th1: temp=55.2 th2: temp=62.1 th3: temp=59.6 sysload=0.05 cputime=466.104 memavail=7394560 print_time=6292.809 buffer_time=2.004 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 60 Hz
Stats 6269.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=28666395 bytes_read=4498585 bytes_retransmit=9 bytes_invalid=0 send_seq=542564 receive_seq=542564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=1628 freq=400015808 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=38848 bytes_read=121631 bytes_retransmit=0 bytes_invalid=0 send_seq=6446 receive_seq=6446 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999575 adj=49997675 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191980 bytes_read=6123734 bytes_retransmit=9 bytes_invalid=0 send_seq=26700 receive_seq=26700 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997616 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=120250 bytes_read=3088785 bytes_retransmit=9 bytes_invalid=0 send_seq=16551 receive_seq=16551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997456 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39115 bytes_read=1600402 bytes_retransmit=9 bytes_invalid=0 send_seq=6460 receive_seq=6460 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997604 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39601 bytes_read=119247 bytes_retransmit=9 bytes_invalid=0 send_seq=6447 receive_seq=6447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93693 bytes_read=2458133 bytes_retransmit=0 bytes_invalid=0 send_seq=11006 receive_seq=11006 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998645 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.1 th2: temp=62.0 th3: temp=59.6 sysload=0.05 cputime=466.219 memavail=7394560 print_time=6294.013 buffer_time=2.208 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 61 Hz
Stats 6270.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=28671506 bytes_read=4499405 bytes_retransmit=9 bytes_invalid=0 send_seq=542661 receive_seq=542661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=2012 freq=400015798 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38854 bytes_read=121660 bytes_retransmit=0 bytes_invalid=0 send_seq=6447 receive_seq=6447 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999577 adj=49997674 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191986 bytes_read=6123848 bytes_retransmit=9 bytes_invalid=0 send_seq=26701 receive_seq=26701 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997631 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=120326 bytes_read=3091899 bytes_retransmit=9 bytes_invalid=0 send_seq=16562 receive_seq=16562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997473 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39121 bytes_read=1600636 bytes_retransmit=9 bytes_invalid=0 send_seq=6461 receive_seq=6461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39607 bytes_read=119263 bytes_retransmit=9 bytes_invalid=0 send_seq=6448 receive_seq=6448 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93699 bytes_read=2458478 bytes_retransmit=0 bytes_invalid=0 send_seq=11007 receive_seq=11007 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998675 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=55.8 th1: temp=55.2 th2: temp=62.0 th3: temp=59.6 sysload=0.04 cputime=466.323 memavail=7394560 print_time=6294.903 buffer_time=2.097 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 62 Hz
Stats 6271.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=28676928 bytes_read=4500215 bytes_retransmit=9 bytes_invalid=0 send_seq=542761 receive_seq=542761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=1234 freq=400015805 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38860 bytes_read=121676 bytes_retransmit=0 bytes_invalid=0 send_seq=6448 receive_seq=6448 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999578 adj=49997701 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191992 bytes_read=6123962 bytes_retransmit=9 bytes_invalid=0 send_seq=26702 receive_seq=26702 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997650 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=120402 bytes_read=3094985 bytes_retransmit=9 bytes_invalid=0 send_seq=16573 receive_seq=16573 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39127 bytes_read=1600930 bytes_retransmit=9 bytes_invalid=0 send_seq=6462 receive_seq=6462 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997706 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39613 bytes_read=119279 bytes_retransmit=9 bytes_invalid=0 send_seq=6449 receive_seq=6449 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93705 bytes_read=2458823 bytes_retransmit=0 bytes_invalid=0 send_seq=11008 receive_seq=11008 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998675 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=55.7 th1: temp=55.2 th2: temp=62.1 th3: temp=59.6 sysload=0.04 cputime=466.433 memavail=7394060 print_time=6295.821 buffer_time=2.014 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 63 Hz
Stats 6272.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=28682907 bytes_read=4501106 bytes_retransmit=9 bytes_invalid=0 send_seq=542874 receive_seq=542874 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=2086 freq=400015800 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38866 bytes_read=121692 bytes_retransmit=0 bytes_invalid=0 send_seq=6449 receive_seq=6449 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999580 adj=49997692 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=191998 bytes_read=6124062 bytes_retransmit=9 bytes_invalid=0 send_seq=26703 receive_seq=26703 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997635 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=120478 bytes_read=3098045 bytes_retransmit=9 bytes_invalid=0 send_seq=16584 receive_seq=16584 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39133 bytes_read=1601164 bytes_retransmit=9 bytes_invalid=0 send_seq=6463 receive_seq=6463 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997679 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39619 bytes_read=119306 bytes_retransmit=9 bytes_invalid=0 send_seq=6450 receive_seq=6450 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93711 bytes_read=2459168 bytes_retransmit=0 bytes_invalid=0 send_seq=11009 receive_seq=11009 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998654 coil_temp=16.9 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=55.9 th1: temp=55.2 th2: temp=62.1 th3: temp=59.7 sysload=0.04 cputime=466.562 memavail=7395164 print_time=6297.034 buffer_time=2.227 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 64 Hz
Stats 6273.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=28688130 bytes_read=4501925 bytes_retransmit=9 bytes_invalid=0 send_seq=542970 receive_seq=542970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=47 upcoming_bytes=2349 freq=400015834 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38872 bytes_read=121708 bytes_retransmit=0 bytes_invalid=0 send_seq=6450 receive_seq=6450 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999582 adj=49997700 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192004 bytes_read=6124190 bytes_retransmit=9 bytes_invalid=0 send_seq=26704 receive_seq=26704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997652 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=120554 bytes_read=3101133 bytes_retransmit=9 bytes_invalid=0 send_seq=16595 receive_seq=16595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39139 bytes_read=1601398 bytes_retransmit=9 bytes_invalid=0 send_seq=6464 receive_seq=6464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39625 bytes_read=119322 bytes_retransmit=9 bytes_invalid=0 send_seq=6451 receive_seq=6451 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93717 bytes_read=2459513 bytes_retransmit=0 bytes_invalid=0 send_seq=11010 receive_seq=11010 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998655 coil_temp=16.9 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=55.9 th1: temp=55.0 th2: temp=61.9 th3: temp=59.7 sysload=0.04 cputime=466.667 memavail=7395164 print_time=6297.902 buffer_time=2.094 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 65 Hz
Stats 6274.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=28693784 bytes_read=4502765 bytes_retransmit=9 bytes_invalid=0 send_seq=543076 receive_seq=543076 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=1655 freq=400015834 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38878 bytes_read=121724 bytes_retransmit=0 bytes_invalid=0 send_seq=6451 receive_seq=6451 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999582 adj=49997651 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192010 bytes_read=6124304 bytes_retransmit=9 bytes_invalid=0 send_seq=26705 receive_seq=26705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997604 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=120630 bytes_read=3104204 bytes_retransmit=9 bytes_invalid=0 send_seq=16606 receive_seq=16606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39145 bytes_read=1601707 bytes_retransmit=9 bytes_invalid=0 send_seq=6465 receive_seq=6465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997614 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39631 bytes_read=119338 bytes_retransmit=9 bytes_invalid=0 send_seq=6452 receive_seq=6452 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93723 bytes_read=2459865 bytes_retransmit=0 bytes_invalid=0 send_seq=11011 receive_seq=11011 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998612 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=55.9 th1: temp=55.2 th2: temp=62.1 th3: temp=59.6 sysload=0.04 cputime=466.783 memavail=7395164 print_time=6298.837 buffer_time=2.028 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 66 Hz
Stats 6275.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=28699926 bytes_read=4503645 bytes_retransmit=9 bytes_invalid=0 send_seq=543190 receive_seq=543190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=2431 freq=400015819 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38884 bytes_read=121753 bytes_retransmit=0 bytes_invalid=0 send_seq=6452 receive_seq=6452 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999583 adj=49997644 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192016 bytes_read=6124404 bytes_retransmit=9 bytes_invalid=0 send_seq=26706 receive_seq=26706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997613 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=120706 bytes_read=3107264 bytes_retransmit=9 bytes_invalid=0 send_seq=16617 receive_seq=16617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997491 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39151 bytes_read=1601941 bytes_retransmit=9 bytes_invalid=0 send_seq=6466 receive_seq=6466 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997613 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39637 bytes_read=119354 bytes_retransmit=9 bytes_invalid=0 send_seq=6453 receive_seq=6453 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93729 bytes_read=2460221 bytes_retransmit=0 bytes_invalid=0 send_seq=11012 receive_seq=11012 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998639 coil_temp=16.9 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.0 th2: temp=62.1 th3: temp=59.6 sysload=0.04 cputime=466.903 memavail=7394940 print_time=6300.040 buffer_time=2.231 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 67 Hz
Stats 6276.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=28705392 bytes_read=4504510 bytes_retransmit=9 bytes_invalid=0 send_seq=543293 receive_seq=543293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=2629 freq=400015823 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38896 bytes_read=121785 bytes_retransmit=0 bytes_invalid=0 send_seq=6454 receive_seq=6454 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999586 adj=49997676 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192028 bytes_read=6124534 bytes_retransmit=9 bytes_invalid=0 send_seq=26708 receive_seq=26708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997653 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=120788 bytes_read=3110351 bytes_retransmit=9 bytes_invalid=0 send_seq=16629 receive_seq=16629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39163 bytes_read=1602191 bytes_retransmit=9 bytes_invalid=0 send_seq=6468 receive_seq=6468 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39649 bytes_read=119386 bytes_retransmit=9 bytes_invalid=0 send_seq=6455 receive_seq=6455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93741 bytes_read=2460593 bytes_retransmit=0 bytes_invalid=0 send_seq=11014 receive_seq=11014 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998652 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.2 th2: temp=62.2 th3: temp=59.6 sysload=0.04 cputime=467.011 memavail=7394940 print_time=6300.920 buffer_time=2.110 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 68 Hz
Stats 6277.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28711136 bytes_read=4505371 bytes_retransmit=9 bytes_invalid=0 send_seq=543400 receive_seq=543400 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=2033 freq=400015817 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38902 bytes_read=121801 bytes_retransmit=0 bytes_invalid=0 send_seq=6455 receive_seq=6455 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999588 adj=49997697 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192034 bytes_read=6124648 bytes_retransmit=9 bytes_invalid=0 send_seq=26709 receive_seq=26709 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997710 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=120864 bytes_read=3113479 bytes_retransmit=9 bytes_invalid=0 send_seq=16640 receive_seq=16640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997493 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39169 bytes_read=1602485 bytes_retransmit=9 bytes_invalid=0 send_seq=6469 receive_seq=6469 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39655 bytes_read=119413 bytes_retransmit=9 bytes_invalid=0 send_seq=6456 receive_seq=6456 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93747 bytes_read=2460949 bytes_retransmit=0 bytes_invalid=0 send_seq=11015 receive_seq=11015 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998641 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=55.6 th1: temp=55.3 th2: temp=62.2 th3: temp=59.6 sysload=0.04 cputime=467.121 memavail=7394460 print_time=6301.848 buffer_time=2.037 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 69 Hz
Stats 6278.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28717373 bytes_read=4506256 bytes_retransmit=9 bytes_invalid=0 send_seq=543515 receive_seq=543515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=2817 freq=400015820 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38908 bytes_read=121817 bytes_retransmit=0 bytes_invalid=0 send_seq=6456 receive_seq=6456 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999590 adj=49997722 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192040 bytes_read=6124762 bytes_retransmit=9 bytes_invalid=0 send_seq=26710 receive_seq=26710 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997709 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=120940 bytes_read=3116555 bytes_retransmit=9 bytes_invalid=0 send_seq=16651 receive_seq=16651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39175 bytes_read=1602719 bytes_retransmit=9 bytes_invalid=0 send_seq=6470 receive_seq=6470 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39661 bytes_read=119429 bytes_retransmit=9 bytes_invalid=0 send_seq=6457 receive_seq=6457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93753 bytes_read=2461305 bytes_retransmit=0 bytes_invalid=0 send_seq=11016 receive_seq=11016 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998675 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.3 th2: temp=62.2 th3: temp=59.5 sysload=0.04 cputime=467.244 memavail=7394460 print_time=6303.046 buffer_time=2.235 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 70 Hz
Stats 6279.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28723104 bytes_read=4507130 bytes_retransmit=9 bytes_invalid=0 send_seq=543622 receive_seq=543622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=46 upcoming_bytes=2962 freq=400015849 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38914 bytes_read=121832 bytes_retransmit=0 bytes_invalid=0 send_seq=6457 receive_seq=6457 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999591 adj=49997704 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192046 bytes_read=6124876 bytes_retransmit=9 bytes_invalid=0 send_seq=26711 receive_seq=26711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997690 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=121016 bytes_read=3119626 bytes_retransmit=9 bytes_invalid=0 send_seq=16662 receive_seq=16662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39181 bytes_read=1602968 bytes_retransmit=9 bytes_invalid=0 send_seq=6471 receive_seq=6471 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39667 bytes_read=119445 bytes_retransmit=9 bytes_invalid=0 send_seq=6458 receive_seq=6458 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93759 bytes_read=2461661 bytes_retransmit=0 bytes_invalid=0 send_seq=11017 receive_seq=11017 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998664 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=55.9 th1: temp=55.1 th2: temp=62.1 th3: temp=59.7 sysload=0.04 cputime=467.355 memavail=7394460 print_time=6303.936 buffer_time=2.124 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 71 Hz
Stats 6280.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28728929 bytes_read=4507972 bytes_retransmit=9 bytes_invalid=0 send_seq=543729 receive_seq=543729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=2320 freq=400015873 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38920 bytes_read=121860 bytes_retransmit=0 bytes_invalid=0 send_seq=6458 receive_seq=6458 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999591 adj=49997658 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192052 bytes_read=6124990 bytes_retransmit=9 bytes_invalid=0 send_seq=26712 receive_seq=26712 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997624 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=121085 bytes_read=3122675 bytes_retransmit=9 bytes_invalid=0 send_seq=16672 receive_seq=16672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997443 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39187 bytes_read=1603262 bytes_retransmit=9 bytes_invalid=0 send_seq=6472 receive_seq=6472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997616 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39673 bytes_read=119461 bytes_retransmit=9 bytes_invalid=0 send_seq=6459 receive_seq=6459 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93765 bytes_read=2462017 bytes_retransmit=0 bytes_invalid=0 send_seq=11018 receive_seq=11018 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998625 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=55.9 th1: temp=55.1 th2: temp=62.0 th3: temp=59.6 sysload=0.03 cputime=467.468 memavail=7394460 print_time=6304.850 buffer_time=2.037 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 72 Hz
Stats 6281.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28735475 bytes_read=4508885 bytes_retransmit=9 bytes_invalid=0 send_seq=543850 receive_seq=543850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=3245 freq=400015911 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38926 bytes_read=121875 bytes_retransmit=0 bytes_invalid=0 send_seq=6459 receive_seq=6459 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999592 adj=49997614 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192058 bytes_read=6125090 bytes_retransmit=9 bytes_invalid=0 send_seq=26713 receive_seq=26713 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997581 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=121161 bytes_read=3125732 bytes_retransmit=9 bytes_invalid=0 send_seq=16683 receive_seq=16683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997407 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39193 bytes_read=1603496 bytes_retransmit=9 bytes_invalid=0 send_seq=6473 receive_seq=6473 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997580 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39679 bytes_read=119477 bytes_retransmit=9 bytes_invalid=0 send_seq=6460 receive_seq=6460 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999415 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93771 bytes_read=2462373 bytes_retransmit=0 bytes_invalid=0 send_seq=11019 receive_seq=11019 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998598 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.1 th2: temp=62.1 th3: temp=59.7 sysload=0.03 cputime=467.593 memavail=7394460 print_time=6306.064 buffer_time=2.251 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 73 Hz
Stats 6282.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28741236 bytes_read=4509780 bytes_retransmit=9 bytes_invalid=0 send_seq=543958 receive_seq=543958 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=46 upcoming_bytes=3310 freq=400015932 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38932 bytes_read=121890 bytes_retransmit=0 bytes_invalid=0 send_seq=6460 receive_seq=6460 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999593 adj=49997572 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192064 bytes_read=6125218 bytes_retransmit=9 bytes_invalid=0 send_seq=26714 receive_seq=26714 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997544 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=121237 bytes_read=3128806 bytes_retransmit=9 bytes_invalid=0 send_seq=16694 receive_seq=16694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997366 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39199 bytes_read=1603730 bytes_retransmit=9 bytes_invalid=0 send_seq=6474 receive_seq=6474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997546 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39685 bytes_read=119504 bytes_retransmit=9 bytes_invalid=0 send_seq=6461 receive_seq=6461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999408 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93777 bytes_read=2462729 bytes_retransmit=0 bytes_invalid=0 send_seq=11020 receive_seq=11020 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998584 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.0 th2: temp=62.2 th3: temp=59.8 sysload=0.03 cputime=467.706 memavail=7394208 print_time=6306.947 buffer_time=2.134 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 74 Hz
Stats 6283.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28747297 bytes_read=4510655 bytes_retransmit=9 bytes_invalid=0 send_seq=544071 receive_seq=544071 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=2904 freq=400015945 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38938 bytes_read=121905 bytes_retransmit=0 bytes_invalid=0 send_seq=6461 receive_seq=6461 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999594 adj=49997557 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192070 bytes_read=6125318 bytes_retransmit=9 bytes_invalid=0 send_seq=26715 receive_seq=26715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997509 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=121313 bytes_read=3131893 bytes_retransmit=9 bytes_invalid=0 send_seq=16705 receive_seq=16705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997335 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39205 bytes_read=1604024 bytes_retransmit=9 bytes_invalid=0 send_seq=6475 receive_seq=6475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997519 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39691 bytes_read=119520 bytes_retransmit=9 bytes_invalid=0 send_seq=6462 receive_seq=6462 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999406 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93783 bytes_read=2463085 bytes_retransmit=0 bytes_invalid=0 send_seq=11021 receive_seq=11021 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998562 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.1 th2: temp=62.2 th3: temp=59.6 sysload=0.03 cputime=467.819 memavail=7394212 print_time=6307.874 buffer_time=2.061 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 75 Hz
Stats 6284.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28753897 bytes_read=4511555 bytes_retransmit=9 bytes_invalid=0 send_seq=544189 receive_seq=544189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=3948 freq=400015948 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38944 bytes_read=121921 bytes_retransmit=0 bytes_invalid=0 send_seq=6462 receive_seq=6462 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999597 adj=49997549 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192076 bytes_read=6125432 bytes_retransmit=9 bytes_invalid=0 send_seq=26716 receive_seq=26716 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997567 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=121389 bytes_read=3134951 bytes_retransmit=9 bytes_invalid=0 send_seq=16716 receive_seq=16716 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997322 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39211 bytes_read=1604273 bytes_retransmit=9 bytes_invalid=0 send_seq=6476 receive_seq=6476 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997511 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39697 bytes_read=119536 bytes_retransmit=9 bytes_invalid=0 send_seq=6463 receive_seq=6463 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999404 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93789 bytes_read=2463441 bytes_retransmit=0 bytes_invalid=0 send_seq=11022 receive_seq=11022 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998560 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.3 th2: temp=62.2 th3: temp=59.7 sysload=0.03 cputime=467.951 memavail=7391968 print_time=6309.090 buffer_time=2.275 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 76 Hz
Stats 6285.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28759870 bytes_read=4512434 bytes_retransmit=9 bytes_invalid=0 send_seq=544297 receive_seq=544297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=3588 freq=400015944 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38950 bytes_read=121950 bytes_retransmit=0 bytes_invalid=0 send_seq=6463 receive_seq=6463 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999597 adj=49997593 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192082 bytes_read=6125550 bytes_retransmit=9 bytes_invalid=0 send_seq=26717 receive_seq=26717 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997595 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=121465 bytes_read=3138063 bytes_retransmit=9 bytes_invalid=0 send_seq=16727 receive_seq=16727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997442 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39217 bytes_read=1604507 bytes_retransmit=9 bytes_invalid=0 send_seq=6477 receive_seq=6477 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997545 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39703 bytes_read=119552 bytes_retransmit=9 bytes_invalid=0 send_seq=6464 receive_seq=6464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999415 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93795 bytes_read=2463797 bytes_retransmit=0 bytes_invalid=0 send_seq=11023 receive_seq=11023 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998592 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.1 th2: temp=62.3 th3: temp=59.6 sysload=0.11 cputime=468.063 memavail=7394492 print_time=6309.955 buffer_time=2.140 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 77 Hz
Stats 6286.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28765957 bytes_read=4513279 bytes_retransmit=9 bytes_invalid=0 send_seq=544404 receive_seq=544404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=3453 freq=400015945 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38956 bytes_read=121966 bytes_retransmit=0 bytes_invalid=0 send_seq=6464 receive_seq=6464 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999598 adj=49997602 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192088 bytes_read=6125643 bytes_retransmit=9 bytes_invalid=0 send_seq=26718 receive_seq=26718 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997659 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=121541 bytes_read=3141116 bytes_retransmit=9 bytes_invalid=0 send_seq=16738 receive_seq=16738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997454 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39223 bytes_read=1604801 bytes_retransmit=9 bytes_invalid=0 send_seq=6478 receive_seq=6478 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997555 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39709 bytes_read=119568 bytes_retransmit=9 bytes_invalid=0 send_seq=6465 receive_seq=6465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999416 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93801 bytes_read=2464153 bytes_retransmit=0 bytes_invalid=0 send_seq=11024 receive_seq=11024 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998600 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.2 th2: temp=62.2 th3: temp=59.7 sysload=0.11 cputime=468.176 memavail=7394492 print_time=6310.894 buffer_time=2.079 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 78 Hz
Stats 6287.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=28772785 bytes_read=4514230 bytes_retransmit=9 bytes_invalid=0 send_seq=544529 receive_seq=544529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=4342 freq=400015934 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38962 bytes_read=121982 bytes_retransmit=0 bytes_invalid=0 send_seq=6465 receive_seq=6465 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999599 adj=49997612 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192094 bytes_read=6125736 bytes_retransmit=9 bytes_invalid=0 send_seq=26719 receive_seq=26719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997761 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=121617 bytes_read=3144158 bytes_retransmit=9 bytes_invalid=0 send_seq=16749 receive_seq=16749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997447 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39229 bytes_read=1605035 bytes_retransmit=9 bytes_invalid=0 send_seq=6479 receive_seq=6479 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997563 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39715 bytes_read=119595 bytes_retransmit=9 bytes_invalid=0 send_seq=6466 receive_seq=6466 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999418 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93807 bytes_read=2464509 bytes_retransmit=0 bytes_invalid=0 send_seq=11025 receive_seq=11025 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998607 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.4 th2: temp=62.4 th3: temp=59.6 sysload=0.11 cputime=468.299 memavail=7394016 print_time=6312.094 buffer_time=2.278 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 79 Hz
Stats 6288.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=28778964 bytes_read=4515139 bytes_retransmit=9 bytes_invalid=0 send_seq=544643 receive_seq=544643 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=3906 freq=400015922 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38968 bytes_read=121998 bytes_retransmit=0 bytes_invalid=0 send_seq=6466 receive_seq=6466 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999599 adj=49997636 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192100 bytes_read=6125855 bytes_retransmit=9 bytes_invalid=0 send_seq=26720 receive_seq=26720 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997809 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=121693 bytes_read=3147229 bytes_retransmit=9 bytes_invalid=0 send_seq=16760 receive_seq=16760 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997555 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39235 bytes_read=1605269 bytes_retransmit=9 bytes_invalid=0 send_seq=6480 receive_seq=6480 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39721 bytes_read=119611 bytes_retransmit=9 bytes_invalid=0 send_seq=6467 receive_seq=6467 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93813 bytes_read=2464865 bytes_retransmit=0 bytes_invalid=0 send_seq=11026 receive_seq=11026 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998660 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.0 th2: temp=62.2 th3: temp=59.7 sysload=0.11 cputime=468.411 memavail=7394016 print_time=6312.971 buffer_time=2.154 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 80 Hz
Stats 6289.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=28785259 bytes_read=4516029 bytes_retransmit=9 bytes_invalid=0 send_seq=544759 receive_seq=544759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=3769 freq=400015955 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38974 bytes_read=122014 bytes_retransmit=0 bytes_invalid=0 send_seq=6467 receive_seq=6467 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999600 adj=49997662 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192106 bytes_read=6125969 bytes_retransmit=9 bytes_invalid=0 send_seq=26721 receive_seq=26721 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997794 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=121769 bytes_read=3150294 bytes_retransmit=9 bytes_invalid=0 send_seq=16771 receive_seq=16771 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997656 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39241 bytes_read=1605578 bytes_retransmit=9 bytes_invalid=0 send_seq=6481 receive_seq=6481 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39727 bytes_read=119627 bytes_retransmit=9 bytes_invalid=0 send_seq=6468 receive_seq=6468 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93819 bytes_read=2465221 bytes_retransmit=0 bytes_invalid=0 send_seq=11027 receive_seq=11027 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998666 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.6 th2: temp=62.3 th3: temp=59.7 sysload=0.11 cputime=468.537 memavail=7394884 print_time=6313.903 buffer_time=2.086 print_stall=0 extruder: target=0 temp=19.3 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 81 Hz
Stats 6290.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=28792120 bytes_read=4516964 bytes_retransmit=9 bytes_invalid=0 send_seq=544884 receive_seq=544884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=4696 freq=400015955 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38980 bytes_read=122043 bytes_retransmit=0 bytes_invalid=0 send_seq=6468 receive_seq=6468 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999601 adj=49997615 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192112 bytes_read=6126069 bytes_retransmit=9 bytes_invalid=0 send_seq=26722 receive_seq=26722 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997696 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=121845 bytes_read=3153350 bytes_retransmit=9 bytes_invalid=0 send_seq=16782 receive_seq=16782 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997555 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39247 bytes_read=1605812 bytes_retransmit=9 bytes_invalid=0 send_seq=6482 receive_seq=6482 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997601 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39733 bytes_read=119643 bytes_retransmit=9 bytes_invalid=0 send_seq=6469 receive_seq=6469 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999418 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93825 bytes_read=2465577 bytes_retransmit=0 bytes_invalid=0 send_seq=11028 receive_seq=11028 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998629 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.2 th2: temp=62.3 th3: temp=59.7 sysload=0.10 cputime=468.667 memavail=7396576 print_time=6315.102 buffer_time=2.284 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 82 Hz
Stats 6291.2: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=28798443 bytes_read=4517876 bytes_retransmit=9 bytes_invalid=0 send_seq=545000 receive_seq=545000 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=4098 freq=400015945 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38986 bytes_read=122059 bytes_retransmit=0 bytes_invalid=0 send_seq=6469 receive_seq=6469 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999602 adj=49997624 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192118 bytes_read=6126197 bytes_retransmit=9 bytes_invalid=0 send_seq=26723 receive_seq=26723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997677 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=121921 bytes_read=3156420 bytes_retransmit=9 bytes_invalid=0 send_seq=16793 receive_seq=16793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997550 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39253 bytes_read=1606046 bytes_retransmit=9 bytes_invalid=0 send_seq=6483 receive_seq=6483 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997613 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39739 bytes_read=119659 bytes_retransmit=9 bytes_invalid=0 send_seq=6470 receive_seq=6470 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93831 bytes_read=2465933 bytes_retransmit=0 bytes_invalid=0 send_seq=11029 receive_seq=11029 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998676 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.2 th2: temp=62.3 th3: temp=59.8 sysload=0.10 cputime=468.782 memavail=7396576 print_time=6315.973 buffer_time=2.155 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 83 Hz
Stats 6292.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28804832 bytes_read=4518792 bytes_retransmit=9 bytes_invalid=0 send_seq=545118 receive_seq=545118 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=4134 freq=400015938 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38992 bytes_read=122075 bytes_retransmit=0 bytes_invalid=0 send_seq=6470 receive_seq=6470 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999603 adj=49997646 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192124 bytes_read=6126297 bytes_retransmit=9 bytes_invalid=0 send_seq=26724 receive_seq=26724 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997745 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=121997 bytes_read=3159549 bytes_retransmit=9 bytes_invalid=0 send_seq=16804 receive_seq=16804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997630 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39259 bytes_read=1606340 bytes_retransmit=9 bytes_invalid=0 send_seq=6484 receive_seq=6484 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39745 bytes_read=119686 bytes_retransmit=9 bytes_invalid=0 send_seq=6471 receive_seq=6471 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93837 bytes_read=2466289 bytes_retransmit=0 bytes_invalid=0 send_seq=11030 receive_seq=11030 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998677 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=55.8 th1: temp=55.2 th2: temp=62.3 th3: temp=59.6 sysload=0.10 cputime=468.900 memavail=7396352 print_time=6316.917 buffer_time=2.098 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 84 Hz
Stats 6293.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28811931 bytes_read=4519752 bytes_retransmit=9 bytes_invalid=0 send_seq=545248 receive_seq=545248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=4974 freq=400015922 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=38998 bytes_read=122091 bytes_retransmit=0 bytes_invalid=0 send_seq=6471 receive_seq=6471 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999604 adj=49997660 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192130 bytes_read=6126397 bytes_retransmit=9 bytes_invalid=0 send_seq=26725 receive_seq=26725 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997797 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=122073 bytes_read=3162622 bytes_retransmit=9 bytes_invalid=0 send_seq=16815 receive_seq=16815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997602 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39265 bytes_read=1606574 bytes_retransmit=9 bytes_invalid=0 send_seq=6485 receive_seq=6485 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39751 bytes_read=119702 bytes_retransmit=9 bytes_invalid=0 send_seq=6472 receive_seq=6472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93843 bytes_read=2466645 bytes_retransmit=0 bytes_invalid=0 send_seq=11031 receive_seq=11031 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998675 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.2 th2: temp=62.3 th3: temp=59.7 sysload=0.10 cputime=469.028 memavail=7396352 print_time=6318.118 buffer_time=2.298 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 85 Hz
Stats 6294.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28818306 bytes_read=4520681 bytes_retransmit=9 bytes_invalid=0 send_seq=545366 receive_seq=545366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=4299 freq=400015905 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39004 bytes_read=122107 bytes_retransmit=0 bytes_invalid=0 send_seq=6472 receive_seq=6472 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999605 adj=49997678 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192136 bytes_read=6126539 bytes_retransmit=9 bytes_invalid=0 send_seq=26726 receive_seq=26726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997847 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=122149 bytes_read=3165692 bytes_retransmit=9 bytes_invalid=0 send_seq=16826 receive_seq=16826 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997601 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39271 bytes_read=1606823 bytes_retransmit=9 bytes_invalid=0 send_seq=6486 receive_seq=6486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39757 bytes_read=119718 bytes_retransmit=9 bytes_invalid=0 send_seq=6473 receive_seq=6473 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93849 bytes_read=2467001 bytes_retransmit=0 bytes_invalid=0 send_seq=11032 receive_seq=11032 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998680 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.2 th2: temp=62.2 th3: temp=59.6 sysload=0.10 cputime=469.144 memavail=7396352 print_time=6318.976 buffer_time=2.156 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 86 Hz
Stats 6295.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28824640 bytes_read=4521576 bytes_retransmit=9 bytes_invalid=0 send_seq=545483 receive_seq=545483 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=4604 freq=400015893 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39010 bytes_read=122136 bytes_retransmit=0 bytes_invalid=0 send_seq=6473 receive_seq=6473 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999606 adj=49997718 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192142 bytes_read=6126639 bytes_retransmit=9 bytes_invalid=0 send_seq=26727 receive_seq=26727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997844 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=122225 bytes_read=3168762 bytes_retransmit=9 bytes_invalid=0 send_seq=16837 receive_seq=16837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997606 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39277 bytes_read=1607117 bytes_retransmit=9 bytes_invalid=0 send_seq=6487 receive_seq=6487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997694 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39763 bytes_read=119734 bytes_retransmit=9 bytes_invalid=0 send_seq=6474 receive_seq=6474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93855 bytes_read=2467357 bytes_retransmit=0 bytes_invalid=0 send_seq=11033 receive_seq=11033 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998684 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.2 th2: temp=62.3 th3: temp=59.8 sysload=0.09 cputime=469.261 memavail=7396352 print_time=6319.928 buffer_time=2.107 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 87 Hz
Stats 6296.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28831942 bytes_read=4522551 bytes_retransmit=9 bytes_invalid=0 send_seq=545616 receive_seq=545616 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=5293 freq=400015892 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39016 bytes_read=122152 bytes_retransmit=0 bytes_invalid=0 send_seq=6474 receive_seq=6474 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999606 adj=49997726 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192148 bytes_read=6126739 bytes_retransmit=9 bytes_invalid=0 send_seq=26728 receive_seq=26728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997829 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=122301 bytes_read=3171819 bytes_retransmit=9 bytes_invalid=0 send_seq=16848 receive_seq=16848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000075 adj=63997612 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39283 bytes_read=1607351 bytes_retransmit=9 bytes_invalid=0 send_seq=6488 receive_seq=6488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997696 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39769 bytes_read=119750 bytes_retransmit=9 bytes_invalid=0 send_seq=6475 receive_seq=6475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93861 bytes_read=2467713 bytes_retransmit=0 bytes_invalid=0 send_seq=11034 receive_seq=11034 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998705 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.2 th2: temp=62.5 th3: temp=59.7 sysload=0.09 cputime=469.389 memavail=7396352 print_time=6321.121 buffer_time=2.299 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 88 Hz
Stats 6297.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28838482 bytes_read=4523511 bytes_retransmit=9 bytes_invalid=0 send_seq=545737 receive_seq=545737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=4551 freq=400015878 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39022 bytes_read=122168 bytes_retransmit=0 bytes_invalid=0 send_seq=6475 receive_seq=6475 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999607 adj=49997696 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192154 bytes_read=6126867 bytes_retransmit=9 bytes_invalid=0 send_seq=26729 receive_seq=26729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997762 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=122370 bytes_read=3174867 bytes_retransmit=9 bytes_invalid=0 send_seq=16858 receive_seq=16858 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000074 adj=63997686 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39289 bytes_read=1607585 bytes_retransmit=9 bytes_invalid=0 send_seq=6489 receive_seq=6489 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997710 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39775 bytes_read=119777 bytes_retransmit=9 bytes_invalid=0 send_seq=6476 receive_seq=6476 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93867 bytes_read=2468069 bytes_retransmit=0 bytes_invalid=0 send_seq=11035 receive_seq=11035 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998696 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=55.9 th1: temp=55.1 th2: temp=62.5 th3: temp=59.7 sysload=0.09 cputime=469.504 memavail=7395596 print_time=6321.981 buffer_time=2.159 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 89 Hz
Stats 6298.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28844977 bytes_read=4524421 bytes_retransmit=9 bytes_invalid=0 send_seq=545857 receive_seq=545857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=4770 freq=400015870 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39028 bytes_read=122184 bytes_retransmit=0 bytes_invalid=0 send_seq=6476 receive_seq=6476 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999607 adj=49997733 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192160 bytes_read=6126967 bytes_retransmit=9 bytes_invalid=0 send_seq=26730 receive_seq=26730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997756 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=122446 bytes_read=3177954 bytes_retransmit=9 bytes_invalid=0 send_seq=16869 receive_seq=16869 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000072 adj=63997683 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39295 bytes_read=1607879 bytes_retransmit=9 bytes_invalid=0 send_seq=6490 receive_seq=6490 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997722 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39781 bytes_read=119793 bytes_retransmit=9 bytes_invalid=0 send_seq=6477 receive_seq=6477 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93873 bytes_read=2468425 bytes_retransmit=0 bytes_invalid=0 send_seq=11036 receive_seq=11036 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998708 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.0 th1: temp=54.9 th2: temp=62.1 th3: temp=59.7 sysload=0.09 cputime=469.623 memavail=7395596 print_time=6322.926 buffer_time=2.103 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 90 Hz
Stats 6299.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28852403 bytes_read=4525406 bytes_retransmit=9 bytes_invalid=0 send_seq=545992 receive_seq=545992 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=5486 freq=400015890 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39034 bytes_read=122200 bytes_retransmit=0 bytes_invalid=0 send_seq=6477 receive_seq=6477 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999606 adj=49997722 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192166 bytes_read=6127081 bytes_retransmit=9 bytes_invalid=0 send_seq=26731 receive_seq=26731 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997734 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=122522 bytes_read=3181068 bytes_retransmit=9 bytes_invalid=0 send_seq=16880 receive_seq=16880 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997651 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39301 bytes_read=1608128 bytes_retransmit=9 bytes_invalid=0 send_seq=6491 receive_seq=6491 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997711 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39787 bytes_read=119809 bytes_retransmit=9 bytes_invalid=0 send_seq=6478 receive_seq=6478 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93879 bytes_read=2468781 bytes_retransmit=0 bytes_invalid=0 send_seq=11037 receive_seq=11037 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998714 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.012 th0: temp=56.0 th1: temp=55.2 th2: temp=62.3 th3: temp=59.7 sysload=0.09 cputime=469.759 memavail=7395608 print_time=6324.127 buffer_time=2.303 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 91 Hz
Stats 6300.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28859105 bytes_read=4526360 bytes_retransmit=9 bytes_invalid=0 send_seq=546115 receive_seq=546115 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=4640 freq=400015908 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=39040 bytes_read=122229 bytes_retransmit=0 bytes_invalid=0 send_seq=6478 receive_seq=6478 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999606 adj=49997658 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192172 bytes_read=6127209 bytes_retransmit=9 bytes_invalid=0 send_seq=26732 receive_seq=26732 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997666 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=122598 bytes_read=3184138 bytes_retransmit=9 bytes_invalid=0 send_seq=16891 receive_seq=16891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997561 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39307 bytes_read=1608362 bytes_retransmit=9 bytes_invalid=0 send_seq=6492 receive_seq=6492 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39793 bytes_read=119825 bytes_retransmit=9 bytes_invalid=0 send_seq=6479 receive_seq=6479 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93885 bytes_read=2469137 bytes_retransmit=0 bytes_invalid=0 send_seq=11038 receive_seq=11038 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998682 coil_temp=16.8 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=56.0 th1: temp=55.3 th2: temp=62.2 th3: temp=59.6 sysload=0.09 cputime=469.879 memavail=7395608 print_time=6325.000 buffer_time=2.175 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 92 Hz
Stats 6301.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28865615 bytes_read=4527270 bytes_retransmit=9 bytes_invalid=0 send_seq=546235 receive_seq=546235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=5043 freq=400015892 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=39046 bytes_read=122245 bytes_retransmit=0 bytes_invalid=0 send_seq=6479 receive_seq=6479 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999606 adj=49997622 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192178 bytes_read=6127309 bytes_retransmit=9 bytes_invalid=0 send_seq=26733 receive_seq=26733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997622 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=122674 bytes_read=3187211 bytes_retransmit=9 bytes_invalid=0 send_seq=16902 receive_seq=16902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997497 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39313 bytes_read=1608656 bytes_retransmit=9 bytes_invalid=0 send_seq=6493 receive_seq=6493 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39799 bytes_read=119841 bytes_retransmit=9 bytes_invalid=0 send_seq=6480 receive_seq=6480 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999435 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93891 bytes_read=2469493 bytes_retransmit=0 bytes_invalid=0 send_seq=11039 receive_seq=11039 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998651 coil_temp=16.8 refs=0 mcu_temp=20.27 supply_voltage=3.012 th0: temp=56.0 th1: temp=55.0 th2: temp=62.2 th3: temp=59.7 sysload=0.09 cputime=470.000 memavail=7395608 print_time=6325.941 buffer_time=2.115 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 93 Hz
Stats 6302.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28873066 bytes_read=4528250 bytes_retransmit=9 bytes_invalid=0 send_seq=546367 receive_seq=546367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=5873 freq=400015893 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=39052 bytes_read=122261 bytes_retransmit=0 bytes_invalid=0 send_seq=6480 receive_seq=6480 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999606 adj=49997648 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192184 bytes_read=6127409 bytes_retransmit=9 bytes_invalid=0 send_seq=26734 receive_seq=26734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997662 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=122750 bytes_read=3190269 bytes_retransmit=9 bytes_invalid=0 send_seq=16913 receive_seq=16913 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39319 bytes_read=1608890 bytes_retransmit=9 bytes_invalid=0 send_seq=6494 receive_seq=6494 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39805 bytes_read=119868 bytes_retransmit=9 bytes_invalid=0 send_seq=6481 receive_seq=6481 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=29.2 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93897 bytes_read=2469849 bytes_retransmit=0 bytes_invalid=0 send_seq=11040 receive_seq=11040 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998678 coil_temp=16.8 refs=0 mcu_temp=20.27 supply_voltage=3.012 th0: temp=56.0 th1: temp=55.2 th2: temp=62.2 th3: temp=59.6 sysload=0.09 cputime=470.134 memavail=7395608 print_time=6327.138 buffer_time=2.311 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 94 Hz
Stats 6303.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28879828 bytes_read=4529189 bytes_retransmit=9 bytes_invalid=0 send_seq=546487 receive_seq=546487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=4938 freq=400015895 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=39058 bytes_read=122277 bytes_retransmit=0 bytes_invalid=0 send_seq=6481 receive_seq=6481 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999607 adj=49997641 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192190 bytes_read=6127537 bytes_retransmit=9 bytes_invalid=0 send_seq=26735 receive_seq=26735 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997648 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=122826 bytes_read=3193359 bytes_retransmit=9 bytes_invalid=0 send_seq=16924 receive_seq=16924 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997557 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39325 bytes_read=1609124 bytes_retransmit=9 bytes_invalid=0 send_seq=6495 receive_seq=6495 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39811 bytes_read=119884 bytes_retransmit=9 bytes_invalid=0 send_seq=6482 receive_seq=6482 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93903 bytes_read=2470205 bytes_retransmit=0 bytes_invalid=0 send_seq=11041 receive_seq=11041 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998664 coil_temp=16.8 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.1 th2: temp=62.3 th3: temp=59.7 sysload=0.09 cputime=470.255 memavail=7395608 print_time=6328.004 buffer_time=2.177 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 95 Hz
Stats 6304.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28886379 bytes_read=4530089 bytes_retransmit=9 bytes_invalid=0 send_seq=546605 receive_seq=546605 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=5472 freq=400015881 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=39064 bytes_read=122293 bytes_retransmit=0 bytes_invalid=0 send_seq=6482 receive_seq=6482 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999608 adj=49997639 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192196 bytes_read=6127651 bytes_retransmit=9 bytes_invalid=0 send_seq=26736 receive_seq=26736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997629 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=122902 bytes_read=3196430 bytes_retransmit=9 bytes_invalid=0 send_seq=16935 receive_seq=16935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997566 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39331 bytes_read=1609433 bytes_retransmit=9 bytes_invalid=0 send_seq=6496 receive_seq=6496 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39817 bytes_read=119900 bytes_retransmit=9 bytes_invalid=0 send_seq=6483 receive_seq=6483 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93909 bytes_read=2470561 bytes_retransmit=0 bytes_invalid=0 send_seq=11042 receive_seq=11042 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998653 coil_temp=16.8 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.1 th2: temp=62.4 th3: temp=59.7 sysload=0.09 cputime=470.380 memavail=7395652 print_time=6328.944 buffer_time=2.114 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 96 Hz
Stats 6305.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28894099 bytes_read=4531094 bytes_retransmit=9 bytes_invalid=0 send_seq=546744 receive_seq=546744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=15 upcoming_bytes=6331 freq=400015899 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39070 bytes_read=122322 bytes_retransmit=0 bytes_invalid=0 send_seq=6483 receive_seq=6483 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999612 adj=49997679 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192202 bytes_read=6127751 bytes_retransmit=9 bytes_invalid=0 send_seq=26737 receive_seq=26737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997679 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=122978 bytes_read=3199544 bytes_retransmit=9 bytes_invalid=0 send_seq=16946 receive_seq=16946 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997583 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39337 bytes_read=1609667 bytes_retransmit=9 bytes_invalid=0 send_seq=6497 receive_seq=6497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39823 bytes_read=119916 bytes_retransmit=9 bytes_invalid=0 send_seq=6484 receive_seq=6484 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93915 bytes_read=2470917 bytes_retransmit=0 bytes_invalid=0 send_seq=11043 receive_seq=11043 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998683 coil_temp=16.8 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=56.0 th1: temp=55.1 th2: temp=62.4 th3: temp=59.6 sysload=0.08 cputime=470.515 memavail=7395652 print_time=6330.150 buffer_time=2.319 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 97 Hz
Stats 6306.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28901139 bytes_read=4532078 bytes_retransmit=9 bytes_invalid=0 send_seq=546873 receive_seq=546873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=5090 freq=400015898 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39076 bytes_read=122338 bytes_retransmit=0 bytes_invalid=0 send_seq=6484 receive_seq=6484 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999613 adj=49997676 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192208 bytes_read=6127879 bytes_retransmit=9 bytes_invalid=0 send_seq=26738 receive_seq=26738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997654 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=123054 bytes_read=3202630 bytes_retransmit=9 bytes_invalid=0 send_seq=16957 receive_seq=16957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997508 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39343 bytes_read=1609901 bytes_retransmit=9 bytes_invalid=0 send_seq=6498 receive_seq=6498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39829 bytes_read=119932 bytes_retransmit=9 bytes_invalid=0 send_seq=6485 receive_seq=6485 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93921 bytes_read=2471273 bytes_retransmit=0 bytes_invalid=0 send_seq=11044 receive_seq=11044 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998657 coil_temp=16.8 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=55.9 th1: temp=55.1 th2: temp=62.3 th3: temp=59.9 sysload=0.08 cputime=470.648 memavail=7388092 print_time=6331.016 buffer_time=2.184 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 98 Hz
Stats 6307.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28907833 bytes_read=4533019 bytes_retransmit=9 bytes_invalid=0 send_seq=546996 receive_seq=546996 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=5606 freq=400015888 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39082 bytes_read=122354 bytes_retransmit=0 bytes_invalid=0 send_seq=6485 receive_seq=6485 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999612 adj=49997686 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192214 bytes_read=6127979 bytes_retransmit=9 bytes_invalid=0 send_seq=26739 receive_seq=26739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997637 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=123130 bytes_read=3205689 bytes_retransmit=9 bytes_invalid=0 send_seq=16968 receive_seq=16968 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39349 bytes_read=1610195 bytes_retransmit=9 bytes_invalid=0 send_seq=6499 receive_seq=6499 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39835 bytes_read=119959 bytes_retransmit=9 bytes_invalid=0 send_seq=6486 receive_seq=6486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93927 bytes_read=2471613 bytes_retransmit=0 bytes_invalid=0 send_seq=11045 receive_seq=11045 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998661 coil_temp=16.8 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=55.9 th1: temp=55.3 th2: temp=62.3 th3: temp=59.6 sysload=0.08 cputime=470.771 memavail=7394496 print_time=6331.947 buffer_time=2.115 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 99 Hz
Stats 6308.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28915542 bytes_read=4534024 bytes_retransmit=9 bytes_invalid=0 send_seq=547135 receive_seq=547135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=6466 freq=400015873 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39088 bytes_read=122370 bytes_retransmit=0 bytes_invalid=0 send_seq=6486 receive_seq=6486 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999612 adj=49997687 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192220 bytes_read=6128079 bytes_retransmit=9 bytes_invalid=0 send_seq=26740 receive_seq=26740 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997647 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=123206 bytes_read=3208763 bytes_retransmit=9 bytes_invalid=0 send_seq=16979 receive_seq=16979 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000075 adj=63997546 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39355 bytes_read=1610429 bytes_retransmit=9 bytes_invalid=0 send_seq=6500 receive_seq=6500 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39841 bytes_read=119975 bytes_retransmit=9 bytes_invalid=0 send_seq=6487 receive_seq=6487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93933 bytes_read=2471969 bytes_retransmit=0 bytes_invalid=0 send_seq=11046 receive_seq=11046 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998664 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=56.0 th1: temp=55.3 th2: temp=62.1 th3: temp=59.6 sysload=0.08 cputime=470.905 memavail=7394496 print_time=6333.145 buffer_time=2.310 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 100 Hz
Stats 6309.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28922755 bytes_read=4535018 bytes_retransmit=9 bytes_invalid=0 send_seq=547266 receive_seq=547266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=5364 freq=400015873 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39094 bytes_read=122386 bytes_retransmit=0 bytes_invalid=0 send_seq=6487 receive_seq=6487 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999612 adj=49997687 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192226 bytes_read=6128221 bytes_retransmit=9 bytes_invalid=0 send_seq=26741 receive_seq=26741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997665 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=123282 bytes_read=3211849 bytes_retransmit=9 bytes_invalid=0 send_seq=16990 receive_seq=16990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000088 adj=63997638 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39361 bytes_read=1610678 bytes_retransmit=9 bytes_invalid=0 send_seq=6501 receive_seq=6501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39847 bytes_read=119991 bytes_retransmit=9 bytes_invalid=0 send_seq=6488 receive_seq=6488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93939 bytes_read=2472325 bytes_retransmit=0 bytes_invalid=0 send_seq=11047 receive_seq=11047 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998700 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=55.8 th1: temp=55.4 th2: temp=62.3 th3: temp=59.7 sysload=0.08 cputime=471.028 memavail=7394496 print_time=6334.021 buffer_time=2.186 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 101 Hz
Stats 6310.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28929504 bytes_read=4535938 bytes_retransmit=9 bytes_invalid=0 send_seq=547388 receive_seq=547388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=5980 freq=400015877 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39100 bytes_read=122415 bytes_retransmit=0 bytes_invalid=0 send_seq=6488 receive_seq=6488 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999611 adj=49997677 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192232 bytes_read=6128321 bytes_retransmit=9 bytes_invalid=0 send_seq=26742 receive_seq=26742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997648 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=123358 bytes_read=3214905 bytes_retransmit=9 bytes_invalid=0 send_seq=17001 receive_seq=17001 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000084 adj=63997779 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39367 bytes_read=1610972 bytes_retransmit=9 bytes_invalid=0 send_seq=6502 receive_seq=6502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39853 bytes_read=120007 bytes_retransmit=9 bytes_invalid=0 send_seq=6489 receive_seq=6489 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93945 bytes_read=2472681 bytes_retransmit=0 bytes_invalid=0 send_seq=11048 receive_seq=11048 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998707 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.2 th2: temp=62.2 th3: temp=59.7 sysload=0.07 cputime=471.150 memavail=7394496 print_time=6334.957 buffer_time=2.121 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 102 Hz
Stats 6311.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28937454 bytes_read=4536953 bytes_retransmit=9 bytes_invalid=0 send_seq=547529 receive_seq=547529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=36 upcoming_bytes=6761 freq=400015872 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39106 bytes_read=122431 bytes_retransmit=0 bytes_invalid=0 send_seq=6489 receive_seq=6489 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999610 adj=49997658 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192238 bytes_read=6128421 bytes_retransmit=9 bytes_invalid=0 send_seq=26743 receive_seq=26743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997633 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=123434 bytes_read=3217962 bytes_retransmit=9 bytes_invalid=0 send_seq=17012 receive_seq=17012 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000083 adj=63997693 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39373 bytes_read=1611206 bytes_retransmit=9 bytes_invalid=0 send_seq=6503 receive_seq=6503 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39859 bytes_read=120023 bytes_retransmit=9 bytes_invalid=0 send_seq=6490 receive_seq=6490 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93951 bytes_read=2473037 bytes_retransmit=0 bytes_invalid=0 send_seq=11049 receive_seq=11049 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998693 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=56.0 th1: temp=55.4 th2: temp=62.2 th3: temp=59.7 sysload=0.07 cputime=471.293 memavail=7394496 print_time=6336.156 buffer_time=2.319 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 103 Hz
Stats 6312.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28944711 bytes_read=4537961 bytes_retransmit=9 bytes_invalid=0 send_seq=547660 receive_seq=547660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=5539 freq=400015875 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39112 bytes_read=122447 bytes_retransmit=0 bytes_invalid=0 send_seq=6490 receive_seq=6490 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997644 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192244 bytes_read=6128549 bytes_retransmit=9 bytes_invalid=0 send_seq=26744 receive_seq=26744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997679 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=123510 bytes_read=3221107 bytes_retransmit=9 bytes_invalid=0 send_seq=17023 receive_seq=17023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000085 adj=63997647 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39379 bytes_read=1611440 bytes_retransmit=9 bytes_invalid=0 send_seq=6504 receive_seq=6504 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39865 bytes_read=120050 bytes_retransmit=9 bytes_invalid=0 send_seq=6491 receive_seq=6491 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93957 bytes_read=2473393 bytes_retransmit=0 bytes_invalid=0 send_seq=11050 receive_seq=11050 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998678 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=56.3 th1: temp=55.3 th2: temp=62.3 th3: temp=59.8 sysload=0.07 cputime=471.416 memavail=7394496 print_time=6337.027 buffer_time=2.189 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 104 Hz
Stats 6313.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28951639 bytes_read=4538898 bytes_retransmit=9 bytes_invalid=0 send_seq=547786 receive_seq=547786 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=6192 freq=400015916 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39118 bytes_read=122463 bytes_retransmit=0 bytes_invalid=0 send_seq=6491 receive_seq=6491 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997625 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192250 bytes_read=6128649 bytes_retransmit=9 bytes_invalid=0 send_seq=26745 receive_seq=26745 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997655 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=123586 bytes_read=3224180 bytes_retransmit=9 bytes_invalid=0 send_seq=17034 receive_seq=17034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000089 adj=63997645 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39385 bytes_read=1611734 bytes_retransmit=9 bytes_invalid=0 send_seq=6505 receive_seq=6505 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39871 bytes_read=120066 bytes_retransmit=9 bytes_invalid=0 send_seq=6492 receive_seq=6492 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93963 bytes_read=2473749 bytes_retransmit=0 bytes_invalid=0 send_seq=11051 receive_seq=11051 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998663 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=56.0 th1: temp=55.2 th2: temp=62.2 th3: temp=59.7 sysload=0.07 cputime=471.539 memavail=7394496 print_time=6337.958 buffer_time=2.118 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 105 Hz
Stats 6314.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28959662 bytes_read=4539918 bytes_retransmit=9 bytes_invalid=0 send_seq=547928 receive_seq=547928 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=7164 freq=400015948 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39124 bytes_read=122479 bytes_retransmit=0 bytes_invalid=0 send_seq=6492 receive_seq=6492 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997560 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192256 bytes_read=6128763 bytes_retransmit=9 bytes_invalid=0 send_seq=26746 receive_seq=26746 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997561 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=123655 bytes_read=3227213 bytes_retransmit=9 bytes_invalid=0 send_seq=17044 receive_seq=17044 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000086 adj=63997609 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39391 bytes_read=1611983 bytes_retransmit=9 bytes_invalid=0 send_seq=6506 receive_seq=6506 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997598 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39877 bytes_read=120082 bytes_retransmit=9 bytes_invalid=0 send_seq=6493 receive_seq=6493 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93969 bytes_read=2474105 bytes_retransmit=0 bytes_invalid=0 send_seq=11052 receive_seq=11052 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998615 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=56.1 th1: temp=55.3 th2: temp=62.3 th3: temp=59.8 sysload=0.07 cputime=471.675 memavail=7394496 print_time=6339.165 buffer_time=2.319 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 106 Hz
Stats 6315.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28967227 bytes_read=4540942 bytes_retransmit=9 bytes_invalid=0 send_seq=548065 receive_seq=548065 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=5720 freq=400015954 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39130 bytes_read=122508 bytes_retransmit=0 bytes_invalid=0 send_seq=6493 receive_seq=6493 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999608 adj=49997533 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192262 bytes_read=6128891 bytes_retransmit=9 bytes_invalid=0 send_seq=26747 receive_seq=26747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997539 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=123731 bytes_read=3230297 bytes_retransmit=9 bytes_invalid=0 send_seq=17055 receive_seq=17055 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000082 adj=63997489 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39397 bytes_read=1612232 bytes_retransmit=9 bytes_invalid=0 send_seq=6507 receive_seq=6507 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997564 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39883 bytes_read=120098 bytes_retransmit=9 bytes_invalid=0 send_seq=6494 receive_seq=6494 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999419 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93975 bytes_read=2474461 bytes_retransmit=0 bytes_invalid=0 send_seq=11053 receive_seq=11053 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998591 coil_temp=16.8 refs=0 mcu_temp=20.25 supply_voltage=3.012 th0: temp=56.1 th1: temp=55.1 th2: temp=62.2 th3: temp=59.6 sysload=0.15 cputime=471.801 memavail=7394496 print_time=6340.030 buffer_time=2.183 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 107 Hz
Stats 6316.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28974113 bytes_read=4541882 bytes_retransmit=9 bytes_invalid=0 send_seq=548191 receive_seq=548191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=6518 freq=400015948 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39136 bytes_read=122524 bytes_retransmit=0 bytes_invalid=0 send_seq=6494 receive_seq=6494 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999608 adj=49997523 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192268 bytes_read=6128991 bytes_retransmit=9 bytes_invalid=0 send_seq=26748 receive_seq=26748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997526 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=123807 bytes_read=3233355 bytes_retransmit=9 bytes_invalid=0 send_seq=17066 receive_seq=17066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000090 adj=63997440 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39403 bytes_read=1612511 bytes_retransmit=9 bytes_invalid=0 send_seq=6508 receive_seq=6508 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997556 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39889 bytes_read=120114 bytes_retransmit=9 bytes_invalid=0 send_seq=6495 receive_seq=6495 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999418 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93981 bytes_read=2474817 bytes_retransmit=0 bytes_invalid=0 send_seq=11054 receive_seq=11054 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998584 coil_temp=16.8 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.3 th2: temp=62.3 th3: temp=59.8 sysload=0.15 cputime=471.924 memavail=7394496 print_time=6340.967 buffer_time=2.120 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 108 Hz
Stats 6317.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28982328 bytes_read=4542962 bytes_retransmit=9 bytes_invalid=0 send_seq=548339 receive_seq=548339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=7361 freq=400015930 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39142 bytes_read=122540 bytes_retransmit=0 bytes_invalid=0 send_seq=6495 receive_seq=6495 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999608 adj=49997539 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192274 bytes_read=6129091 bytes_retransmit=9 bytes_invalid=0 send_seq=26749 receive_seq=26749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997544 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=123883 bytes_read=3236469 bytes_retransmit=9 bytes_invalid=0 send_seq=17077 receive_seq=17077 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000091 adj=63997557 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39409 bytes_read=1612745 bytes_retransmit=9 bytes_invalid=0 send_seq=6509 receive_seq=6509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997573 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39895 bytes_read=120141 bytes_retransmit=9 bytes_invalid=0 send_seq=6496 receive_seq=6496 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999421 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93987 bytes_read=2475173 bytes_retransmit=0 bytes_invalid=0 send_seq=11055 receive_seq=11055 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998600 coil_temp=16.8 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.3 th2: temp=62.3 th3: temp=59.8 sysload=0.15 cputime=472.064 memavail=7393780 print_time=6342.164 buffer_time=2.316 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 109 Hz
Stats 6318.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28989978 bytes_read=4543962 bytes_retransmit=9 bytes_invalid=0 send_seq=548474 receive_seq=548474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=44 upcoming_bytes=5966 freq=400015930 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39148 bytes_read=122556 bytes_retransmit=0 bytes_invalid=0 send_seq=6496 receive_seq=6496 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999607 adj=49997586 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192280 bytes_read=6129219 bytes_retransmit=9 bytes_invalid=0 send_seq=26750 receive_seq=26750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997600 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=123959 bytes_read=3239573 bytes_retransmit=9 bytes_invalid=0 send_seq=17088 receive_seq=17088 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000087 adj=63997601 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39415 bytes_read=1612994 bytes_retransmit=9 bytes_invalid=0 send_seq=6510 receive_seq=6510 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997613 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39901 bytes_read=120157 bytes_retransmit=9 bytes_invalid=0 send_seq=6497 receive_seq=6497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93993 bytes_read=2475529 bytes_retransmit=0 bytes_invalid=0 send_seq=11056 receive_seq=11056 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998632 coil_temp=16.8 refs=0 mcu_temp=20.25 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.4 th2: temp=62.3 th3: temp=59.8 sysload=0.15 cputime=472.192 memavail=7393816 print_time=6343.042 buffer_time=2.193 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 110 Hz
Stats 6319.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=28996988 bytes_read=4544902 bytes_retransmit=9 bytes_invalid=0 send_seq=548600 receive_seq=548600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=6816 freq=400015922 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39154 bytes_read=122572 bytes_retransmit=0 bytes_invalid=0 send_seq=6497 receive_seq=6497 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999608 adj=49997581 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192286 bytes_read=6129333 bytes_retransmit=9 bytes_invalid=0 send_seq=26751 receive_seq=26751 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997595 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124035 bytes_read=3242629 bytes_retransmit=9 bytes_invalid=0 send_seq=17099 receive_seq=17099 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000094 adj=63997548 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39421 bytes_read=1613288 bytes_retransmit=9 bytes_invalid=0 send_seq=6511 receive_seq=6511 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997612 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39907 bytes_read=120173 bytes_retransmit=9 bytes_invalid=0 send_seq=6498 receive_seq=6498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=93999 bytes_read=2475885 bytes_retransmit=0 bytes_invalid=0 send_seq=11057 receive_seq=11057 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998635 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.3 th2: temp=62.3 th3: temp=59.8 sysload=0.15 cputime=472.318 memavail=7393816 print_time=6343.971 buffer_time=2.123 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 111 Hz
Stats 6320.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29005357 bytes_read=4545986 bytes_retransmit=9 bytes_invalid=0 send_seq=548749 receive_seq=548749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=7629 freq=400015949 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39160 bytes_read=122601 bytes_retransmit=0 bytes_invalid=0 send_seq=6498 receive_seq=6498 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999608 adj=49997609 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192292 bytes_read=6129433 bytes_retransmit=9 bytes_invalid=0 send_seq=26752 receive_seq=26752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997671 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124111 bytes_read=3245687 bytes_retransmit=9 bytes_invalid=0 send_seq=17110 receive_seq=17110 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000092 adj=63997644 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39427 bytes_read=1613522 bytes_retransmit=9 bytes_invalid=0 send_seq=6512 receive_seq=6512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39913 bytes_read=120189 bytes_retransmit=9 bytes_invalid=0 send_seq=6499 receive_seq=6499 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94005 bytes_read=2476259 bytes_retransmit=0 bytes_invalid=0 send_seq=11058 receive_seq=11058 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998649 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=56.0 th1: temp=55.3 th2: temp=62.4 th3: temp=59.7 sysload=0.22 cputime=472.458 memavail=7393816 print_time=6345.174 buffer_time=2.316 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 112 Hz
Stats 6321.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29013282 bytes_read=4547001 bytes_retransmit=9 bytes_invalid=0 send_seq=548890 receive_seq=548890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=5929 freq=400015941 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39166 bytes_read=122617 bytes_retransmit=0 bytes_invalid=0 send_seq=6499 receive_seq=6499 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999608 adj=49997574 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192298 bytes_read=6129561 bytes_retransmit=9 bytes_invalid=0 send_seq=26753 receive_seq=26753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997697 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124187 bytes_read=3248830 bytes_retransmit=9 bytes_invalid=0 send_seq=17121 receive_seq=17121 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000088 adj=63997543 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39433 bytes_read=1613786 bytes_retransmit=9 bytes_invalid=0 send_seq=6513 receive_seq=6513 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997591 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39919 bytes_read=120205 bytes_retransmit=9 bytes_invalid=0 send_seq=6500 receive_seq=6500 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94011 bytes_read=2476615 bytes_retransmit=0 bytes_invalid=0 send_seq=11059 receive_seq=11059 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998620 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=56.1 th1: temp=55.4 th2: temp=62.2 th3: temp=59.8 sysload=0.22 cputime=472.585 memavail=7393832 print_time=6346.044 buffer_time=2.185 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 113 Hz
Stats 6322.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29020296 bytes_read=4547972 bytes_retransmit=9 bytes_invalid=0 send_seq=549019 receive_seq=549019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=29 upcoming_bytes=6810 freq=400015962 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39172 bytes_read=122633 bytes_retransmit=0 bytes_invalid=0 send_seq=6500 receive_seq=6500 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997594 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192304 bytes_read=6129661 bytes_retransmit=9 bytes_invalid=0 send_seq=26754 receive_seq=26754 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997762 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124263 bytes_read=3251888 bytes_retransmit=9 bytes_invalid=0 send_seq=17132 receive_seq=17132 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000095 adj=63997508 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39439 bytes_read=1614050 bytes_retransmit=9 bytes_invalid=0 send_seq=6514 receive_seq=6514 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39925 bytes_read=120232 bytes_retransmit=9 bytes_invalid=0 send_seq=6501 receive_seq=6501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94017 bytes_read=2476971 bytes_retransmit=0 bytes_invalid=0 send_seq=11060 receive_seq=11060 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998623 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=56.1 th1: temp=55.3 th2: temp=62.5 th3: temp=59.7 sysload=0.22 cputime=472.710 memavail=7393832 print_time=6346.978 buffer_time=2.118 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 114 Hz
Stats 6323.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29028697 bytes_read=4549057 bytes_retransmit=9 bytes_invalid=0 send_seq=549169 receive_seq=549169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=7715 freq=400015995 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39178 bytes_read=122649 bytes_retransmit=0 bytes_invalid=0 send_seq=6501 receive_seq=6501 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997569 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192310 bytes_read=6129761 bytes_retransmit=9 bytes_invalid=0 send_seq=26755 receive_seq=26755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997766 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124339 bytes_read=3254961 bytes_retransmit=9 bytes_invalid=0 send_seq=17143 receive_seq=17143 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000092 adj=63997568 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39445 bytes_read=1614284 bytes_retransmit=9 bytes_invalid=0 send_seq=6515 receive_seq=6515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997611 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39931 bytes_read=120248 bytes_retransmit=9 bytes_invalid=0 send_seq=6502 receive_seq=6502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94023 bytes_read=2477343 bytes_retransmit=0 bytes_invalid=0 send_seq=11061 receive_seq=11061 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998600 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=56.0 th1: temp=55.3 th2: temp=62.3 th3: temp=59.6 sysload=0.22 cputime=472.863 memavail=7389308 print_time=6348.180 buffer_time=2.314 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 115 Hz
Stats 6324.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29036650 bytes_read=4550076 bytes_retransmit=9 bytes_invalid=0 send_seq=549312 receive_seq=549311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=6157 freq=400015994 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39184 bytes_read=122665 bytes_retransmit=0 bytes_invalid=0 send_seq=6502 receive_seq=6502 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997532 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=192316 bytes_read=6129903 bytes_retransmit=9 bytes_invalid=0 send_seq=26756 receive_seq=26756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997653 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124415 bytes_read=3258047 bytes_retransmit=9 bytes_invalid=0 send_seq=17154 receive_seq=17154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000089 adj=63997461 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39451 bytes_read=1614578 bytes_retransmit=9 bytes_invalid=0 send_seq=6516 receive_seq=6516 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997568 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39937 bytes_read=120264 bytes_retransmit=9 bytes_invalid=0 send_seq=6503 receive_seq=6503 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999416 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94029 bytes_read=2477683 bytes_retransmit=0 bytes_invalid=0 send_seq=11062 receive_seq=11062 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998579 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=56.1 th1: temp=55.5 th2: temp=62.2 th3: temp=59.7 sysload=0.22 cputime=472.994 memavail=7395720 print_time=6349.048 buffer_time=2.182 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 116 Hz
Stats 6325.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29043585 bytes_read=4551001 bytes_retransmit=9 bytes_invalid=0 send_seq=549434 receive_seq=549434 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=7209 freq=400015976 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39190 bytes_read=122694 bytes_retransmit=0 bytes_invalid=0 send_seq=6503 receive_seq=6503 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997542 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=192322 bytes_read=6130003 bytes_retransmit=9 bytes_invalid=0 send_seq=26757 receive_seq=26757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997710 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124491 bytes_read=3261103 bytes_retransmit=9 bytes_invalid=0 send_seq=17165 receive_seq=17165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000086 adj=63997438 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39457 bytes_read=1614827 bytes_retransmit=9 bytes_invalid=0 send_seq=6517 receive_seq=6517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997576 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39943 bytes_read=120280 bytes_retransmit=9 bytes_invalid=0 send_seq=6504 receive_seq=6504 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999418 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94035 bytes_read=2478039 bytes_retransmit=0 bytes_invalid=0 send_seq=11063 receive_seq=11063 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998583 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.4 th2: temp=62.3 th3: temp=59.7 sysload=0.36 cputime=473.120 memavail=7397528 print_time=6349.977 buffer_time=2.110 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 117 Hz
Stats 6326.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29052266 bytes_read=4552110 bytes_retransmit=9 bytes_invalid=0 send_seq=549588 receive_seq=549588 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=7969 freq=400015959 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39196 bytes_read=122710 bytes_retransmit=0 bytes_invalid=0 send_seq=6504 receive_seq=6504 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997581 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=192328 bytes_read=6130103 bytes_retransmit=9 bytes_invalid=0 send_seq=26758 receive_seq=26758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997711 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124567 bytes_read=3264218 bytes_retransmit=9 bytes_invalid=0 send_seq=17176 receive_seq=17176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000082 adj=63997442 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39463 bytes_read=1615061 bytes_retransmit=9 bytes_invalid=0 send_seq=6518 receive_seq=6518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39949 bytes_read=120296 bytes_retransmit=9 bytes_invalid=0 send_seq=6505 receive_seq=6505 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94041 bytes_read=2478395 bytes_retransmit=0 bytes_invalid=0 send_seq=11064 receive_seq=11064 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998612 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=56.0 th1: temp=55.5 th2: temp=62.2 th3: temp=59.7 sysload=0.36 cputime=473.266 memavail=7397528 print_time=6351.181 buffer_time=2.313 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 118 Hz
Stats 6327.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29060392 bytes_read=4553171 bytes_retransmit=9 bytes_invalid=0 send_seq=549735 receive_seq=549735 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=6231 freq=400015956 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39202 bytes_read=122726 bytes_retransmit=0 bytes_invalid=0 send_seq=6505 receive_seq=6505 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997615 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=192334 bytes_read=6130231 bytes_retransmit=9 bytes_invalid=0 send_seq=26759 receive_seq=26759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997703 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124643 bytes_read=3267302 bytes_retransmit=9 bytes_invalid=0 send_seq=17187 receive_seq=17187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000079 adj=63997457 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39469 bytes_read=1615340 bytes_retransmit=9 bytes_invalid=0 send_seq=6519 receive_seq=6519 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997682 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39955 bytes_read=120323 bytes_retransmit=9 bytes_invalid=0 send_seq=6506 receive_seq=6506 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94047 bytes_read=2478751 bytes_retransmit=0 bytes_invalid=0 send_seq=11065 receive_seq=11065 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998635 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=56.1 th1: temp=55.4 th2: temp=62.2 th3: temp=59.8 sysload=0.36 cputime=473.405 memavail=7396520 print_time=6352.057 buffer_time=2.188 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 119 Hz
Stats 6328.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29067488 bytes_read=4554121 bytes_retransmit=9 bytes_invalid=0 send_seq=549863 receive_seq=549863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=52 upcoming_bytes=7223 freq=400015968 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39208 bytes_read=122742 bytes_retransmit=0 bytes_invalid=0 send_seq=6506 receive_seq=6506 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999608 adj=49997620 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000010 bytes_write=192340 bytes_read=6130331 bytes_retransmit=9 bytes_invalid=0 send_seq=26760 receive_seq=26760 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997683 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124719 bytes_read=3270377 bytes_retransmit=9 bytes_invalid=0 send_seq=17198 receive_seq=17198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000084 adj=63997430 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39475 bytes_read=1615589 bytes_retransmit=9 bytes_invalid=0 send_seq=6520 receive_seq=6520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39961 bytes_read=120339 bytes_retransmit=9 bytes_invalid=0 send_seq=6507 receive_seq=6507 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94053 bytes_read=2479107 bytes_retransmit=0 bytes_invalid=0 send_seq=11066 receive_seq=11066 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998640 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.4 th2: temp=62.3 th3: temp=59.9 sysload=0.36 cputime=473.536 memavail=7396276 print_time=6352.983 buffer_time=2.114 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 120 Hz
Stats 6329.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29076064 bytes_read=4555220 bytes_retransmit=9 bytes_invalid=0 send_seq=550015 receive_seq=550015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=8119 freq=400015964 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39214 bytes_read=122758 bytes_retransmit=0 bytes_invalid=0 send_seq=6507 receive_seq=6507 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999610 adj=49997591 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192346 bytes_read=6130445 bytes_retransmit=9 bytes_invalid=0 send_seq=26761 receive_seq=26761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997638 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124788 bytes_read=3273410 bytes_retransmit=9 bytes_invalid=0 send_seq=17208 receive_seq=17208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000081 adj=63997488 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39481 bytes_read=1615827 bytes_retransmit=9 bytes_invalid=0 send_seq=6521 receive_seq=6521 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39967 bytes_read=120355 bytes_retransmit=9 bytes_invalid=0 send_seq=6508 receive_seq=6508 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94059 bytes_read=2479463 bytes_retransmit=0 bytes_invalid=0 send_seq=11067 receive_seq=11067 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998626 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.1 th2: temp=62.1 th3: temp=59.7 sysload=0.36 cputime=473.684 memavail=7396276 print_time=6354.185 buffer_time=2.313 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 121 Hz
Stats 6330.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29084305 bytes_read=4556250 bytes_retransmit=9 bytes_invalid=0 send_seq=550159 receive_seq=550159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=6378 freq=400015952 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39220 bytes_read=122787 bytes_retransmit=0 bytes_invalid=0 send_seq=6508 receive_seq=6508 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999610 adj=49997629 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192352 bytes_read=6130573 bytes_retransmit=9 bytes_invalid=0 send_seq=26762 receive_seq=26762 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997636 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124864 bytes_read=3276494 bytes_retransmit=9 bytes_invalid=0 send_seq=17219 receive_seq=17219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000077 adj=63997466 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39487 bytes_read=1616087 bytes_retransmit=9 bytes_invalid=0 send_seq=6522 receive_seq=6522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39973 bytes_read=120371 bytes_retransmit=9 bytes_invalid=0 send_seq=6509 receive_seq=6509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94065 bytes_read=2479819 bytes_retransmit=0 bytes_invalid=0 send_seq=11068 receive_seq=11068 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998634 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=55.9 th1: temp=55.3 th2: temp=62.2 th3: temp=59.7 sysload=0.41 cputime=473.817 memavail=7396276 print_time=6355.061 buffer_time=2.188 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 122 Hz
Stats 6331.2: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29091456 bytes_read=4557200 bytes_retransmit=9 bytes_invalid=0 send_seq=550287 receive_seq=550287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=7508 freq=400015950 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39226 bytes_read=122803 bytes_retransmit=0 bytes_invalid=0 send_seq=6509 receive_seq=6509 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997644 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192358 bytes_read=6130673 bytes_retransmit=9 bytes_invalid=0 send_seq=26763 receive_seq=26763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997640 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=124940 bytes_read=3279552 bytes_retransmit=9 bytes_invalid=0 send_seq=17230 receive_seq=17230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000076 adj=63997456 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39493 bytes_read=1616319 bytes_retransmit=9 bytes_invalid=0 send_seq=6523 receive_seq=6523 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39979 bytes_read=120387 bytes_retransmit=9 bytes_invalid=0 send_seq=6510 receive_seq=6510 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94071 bytes_read=2480175 bytes_retransmit=0 bytes_invalid=0 send_seq=11069 receive_seq=11069 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998651 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.4 th2: temp=62.2 th3: temp=59.8 sysload=0.41 cputime=473.946 memavail=7396276 print_time=6355.987 buffer_time=2.114 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 123 Hz
Stats 6332.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29100095 bytes_read=4558330 bytes_retransmit=9 bytes_invalid=0 send_seq=550442 receive_seq=550442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=8491 freq=400015941 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39232 bytes_read=122819 bytes_retransmit=0 bytes_invalid=0 send_seq=6510 receive_seq=6510 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997633 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192364 bytes_read=6130773 bytes_retransmit=9 bytes_invalid=0 send_seq=26764 receive_seq=26764 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997669 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125016 bytes_read=3282609 bytes_retransmit=9 bytes_invalid=0 send_seq=17241 receive_seq=17241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997453 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39499 bytes_read=1616537 bytes_retransmit=9 bytes_invalid=0 send_seq=6524 receive_seq=6524 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997689 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39985 bytes_read=120414 bytes_retransmit=9 bytes_invalid=0 send_seq=6511 receive_seq=6511 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94077 bytes_read=2480531 bytes_retransmit=0 bytes_invalid=0 send_seq=11070 receive_seq=11070 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998649 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.2 th2: temp=62.3 th3: temp=59.7 sysload=0.41 cputime=474.092 memavail=7396276 print_time=6357.186 buffer_time=2.313 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 124 Hz
Stats 6333.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29108588 bytes_read=4559395 bytes_retransmit=9 bytes_invalid=0 send_seq=550593 receive_seq=550593 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=6599 freq=400015952 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39238 bytes_read=122835 bytes_retransmit=0 bytes_invalid=0 send_seq=6511 receive_seq=6511 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997642 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192370 bytes_read=6130901 bytes_retransmit=9 bytes_invalid=0 send_seq=26765 receive_seq=26765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997744 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125092 bytes_read=3285769 bytes_retransmit=9 bytes_invalid=0 send_seq=17252 receive_seq=17252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000075 adj=63997451 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39505 bytes_read=1616797 bytes_retransmit=9 bytes_invalid=0 send_seq=6525 receive_seq=6525 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39991 bytes_read=120430 bytes_retransmit=9 bytes_invalid=0 send_seq=6512 receive_seq=6512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94083 bytes_read=2480887 bytes_retransmit=0 bytes_invalid=0 send_seq=11071 receive_seq=11071 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998676 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.3 th2: temp=62.2 th3: temp=59.6 sysload=0.41 cputime=474.224 memavail=7396276 print_time=6358.062 buffer_time=2.189 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 125 Hz
Stats 6334.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29115819 bytes_read=4560351 bytes_retransmit=9 bytes_invalid=0 send_seq=550723 receive_seq=550723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=7634 freq=400015947 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39244 bytes_read=122851 bytes_retransmit=0 bytes_invalid=0 send_seq=6512 receive_seq=6512 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997620 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192376 bytes_read=6131015 bytes_retransmit=9 bytes_invalid=0 send_seq=26766 receive_seq=26766 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997694 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125168 bytes_read=3288828 bytes_retransmit=9 bytes_invalid=0 send_seq=17263 receive_seq=17263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997461 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39511 bytes_read=1617044 bytes_retransmit=9 bytes_invalid=0 send_seq=6526 receive_seq=6526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=39997 bytes_read=120446 bytes_retransmit=9 bytes_invalid=0 send_seq=6513 receive_seq=6513 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94089 bytes_read=2481243 bytes_retransmit=0 bytes_invalid=0 send_seq=11072 receive_seq=11072 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998666 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.2 th2: temp=62.4 th3: temp=59.9 sysload=0.41 cputime=474.354 memavail=7396276 print_time=6358.988 buffer_time=2.115 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 126 Hz
Stats 6335.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29124579 bytes_read=4561459 bytes_retransmit=9 bytes_invalid=0 send_seq=550877 receive_seq=550877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=47 upcoming_bytes=8539 freq=400015943 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39250 bytes_read=122867 bytes_retransmit=0 bytes_invalid=0 send_seq=6513 receive_seq=6513 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997626 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192382 bytes_read=6131115 bytes_retransmit=9 bytes_invalid=0 send_seq=26767 receive_seq=26767 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997757 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125244 bytes_read=3291884 bytes_retransmit=9 bytes_invalid=0 send_seq=17274 receive_seq=17274 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997457 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39517 bytes_read=1617277 bytes_retransmit=9 bytes_invalid=0 send_seq=6527 receive_seq=6527 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40003 bytes_read=120462 bytes_retransmit=9 bytes_invalid=0 send_seq=6514 receive_seq=6514 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94095 bytes_read=2481599 bytes_retransmit=0 bytes_invalid=0 send_seq=11073 receive_seq=11073 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998680 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.4 th2: temp=62.3 th3: temp=59.7 sysload=0.38 cputime=474.501 memavail=7395800 print_time=6360.189 buffer_time=2.314 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 127 Hz
Stats 6336.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29133124 bytes_read=4562550 bytes_retransmit=9 bytes_invalid=0 send_seq=551031 receive_seq=551031 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=6610 freq=400015918 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39262 bytes_read=122912 bytes_retransmit=0 bytes_invalid=0 send_seq=6515 receive_seq=6515 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997630 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192394 bytes_read=6131259 bytes_retransmit=9 bytes_invalid=0 send_seq=26769 receive_seq=26769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997716 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125326 bytes_read=3294986 bytes_retransmit=9 bytes_invalid=0 send_seq=17286 receive_seq=17286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997454 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39529 bytes_read=1617587 bytes_retransmit=9 bytes_invalid=0 send_seq=6529 receive_seq=6529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997698 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40015 bytes_read=120494 bytes_retransmit=9 bytes_invalid=0 send_seq=6516 receive_seq=6516 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94107 bytes_read=2481971 bytes_retransmit=0 bytes_invalid=0 send_seq=11075 receive_seq=11075 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998689 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.5 th2: temp=62.3 th3: temp=59.7 sysload=0.38 cputime=474.635 memavail=7395800 print_time=6361.058 buffer_time=2.182 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 128 Hz
Stats 6337.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29140344 bytes_read=4563521 bytes_retransmit=9 bytes_invalid=0 send_seq=551160 receive_seq=551160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=7807 freq=400015920 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39268 bytes_read=122928 bytes_retransmit=0 bytes_invalid=0 send_seq=6516 receive_seq=6516 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997665 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192400 bytes_read=6131359 bytes_retransmit=9 bytes_invalid=0 send_seq=26770 receive_seq=26770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997730 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125402 bytes_read=3298045 bytes_retransmit=9 bytes_invalid=0 send_seq=17297 receive_seq=17297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997460 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39535 bytes_read=1617821 bytes_retransmit=9 bytes_invalid=0 send_seq=6530 receive_seq=6530 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997729 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40021 bytes_read=120521 bytes_retransmit=9 bytes_invalid=0 send_seq=6517 receive_seq=6517 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94113 bytes_read=2482327 bytes_retransmit=0 bytes_invalid=0 send_seq=11076 receive_seq=11076 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998723 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.4 th2: temp=62.4 th3: temp=59.9 sysload=0.38 cputime=474.764 memavail=7394792 print_time=6361.994 buffer_time=2.117 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 129 Hz
Stats 6338.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29149235 bytes_read=4564660 bytes_retransmit=9 bytes_invalid=0 send_seq=551320 receive_seq=551320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=8754 freq=400015940 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39274 bytes_read=122944 bytes_retransmit=0 bytes_invalid=0 send_seq=6517 receive_seq=6517 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997655 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192406 bytes_read=6131459 bytes_retransmit=9 bytes_invalid=0 send_seq=26771 receive_seq=26771 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997699 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125478 bytes_read=3301176 bytes_retransmit=9 bytes_invalid=0 send_seq=17308 receive_seq=17308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997433 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39541 bytes_read=1618055 bytes_retransmit=9 bytes_invalid=0 send_seq=6531 receive_seq=6531 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997705 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40027 bytes_read=120537 bytes_retransmit=9 bytes_invalid=0 send_seq=6518 receive_seq=6518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94119 bytes_read=2482683 bytes_retransmit=0 bytes_invalid=0 send_seq=11077 receive_seq=11077 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998726 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.4 th2: temp=62.3 th3: temp=59.7 sysload=0.38 cputime=474.914 memavail=7394572 print_time=6363.197 buffer_time=2.314 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 130 Hz
Stats 6339.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29157877 bytes_read=4565745 bytes_retransmit=9 bytes_invalid=0 send_seq=551475 receive_seq=551475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=6644 freq=400015942 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39280 bytes_read=122960 bytes_retransmit=0 bytes_invalid=0 send_seq=6518 receive_seq=6518 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997614 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192412 bytes_read=6131601 bytes_retransmit=9 bytes_invalid=0 send_seq=26772 receive_seq=26772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997639 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125554 bytes_read=3304262 bytes_retransmit=9 bytes_invalid=0 send_seq=17319 receive_seq=17319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997409 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39547 bytes_read=1618364 bytes_retransmit=9 bytes_invalid=0 send_seq=6532 receive_seq=6532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40033 bytes_read=120553 bytes_retransmit=9 bytes_invalid=0 send_seq=6519 receive_seq=6519 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94125 bytes_read=2483039 bytes_retransmit=0 bytes_invalid=0 send_seq=11078 receive_seq=11078 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998684 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.4 th2: temp=62.2 th3: temp=59.8 sysload=0.38 cputime=475.047 memavail=7394572 print_time=6364.067 buffer_time=2.183 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 131 Hz
Stats 6340.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29165181 bytes_read=4566700 bytes_retransmit=9 bytes_invalid=0 send_seq=551604 receive_seq=551604 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=7881 freq=400015947 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39286 bytes_read=122976 bytes_retransmit=0 bytes_invalid=0 send_seq=6519 receive_seq=6519 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997609 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192418 bytes_read=6131701 bytes_retransmit=9 bytes_invalid=0 send_seq=26773 receive_seq=26773 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997633 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125630 bytes_read=3307320 bytes_retransmit=9 bytes_invalid=0 send_seq=17330 receive_seq=17330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997387 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39553 bytes_read=1618598 bytes_retransmit=9 bytes_invalid=0 send_seq=6533 receive_seq=6533 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999570 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40039 bytes_read=120569 bytes_retransmit=9 bytes_invalid=0 send_seq=6520 receive_seq=6520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94131 bytes_read=2483395 bytes_retransmit=0 bytes_invalid=0 send_seq=11079 receive_seq=11079 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998674 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.4 th2: temp=62.3 th3: temp=59.7 sysload=0.43 cputime=475.179 memavail=7388528 print_time=6364.993 buffer_time=2.108 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 132 Hz
Stats 6341.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29173977 bytes_read=4567829 bytes_retransmit=9 bytes_invalid=0 send_seq=551762 receive_seq=551762 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=9016 freq=400015946 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39292 bytes_read=123005 bytes_retransmit=0 bytes_invalid=0 send_seq=6520 receive_seq=6520 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999610 adj=49997605 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192424 bytes_read=6131801 bytes_retransmit=9 bytes_invalid=0 send_seq=26774 receive_seq=26774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997613 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125706 bytes_read=3310376 bytes_retransmit=9 bytes_invalid=0 send_seq=17341 receive_seq=17341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000074 adj=63997452 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39559 bytes_read=1618832 bytes_retransmit=9 bytes_invalid=0 send_seq=6534 receive_seq=6534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999569 adj=47997753 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40045 bytes_read=120585 bytes_retransmit=9 bytes_invalid=0 send_seq=6521 receive_seq=6521 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94137 bytes_read=2483751 bytes_retransmit=0 bytes_invalid=0 send_seq=11080 receive_seq=11080 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998668 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.3 th2: temp=62.4 th3: temp=59.6 sysload=0.43 cputime=475.335 memavail=7393176 print_time=6366.197 buffer_time=2.312 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Stats 6342.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29182760 bytes_read=4568935 bytes_retransmit=9 bytes_invalid=0 send_seq=551918 receive_seq=551918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=6315 freq=400015965 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39298 bytes_read=123021 bytes_retransmit=0 bytes_invalid=0 send_seq=6521 receive_seq=6521 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999610 adj=49997626 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192430 bytes_read=6131929 bytes_retransmit=9 bytes_invalid=0 send_seq=26775 receive_seq=26775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997774 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125782 bytes_read=3313462 bytes_retransmit=9 bytes_invalid=0 send_seq=17352 receive_seq=17352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997573 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39565 bytes_read=1619126 bytes_retransmit=9 bytes_invalid=0 send_seq=6535 receive_seq=6535 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999568 adj=47997712 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40051 bytes_read=120612 bytes_retransmit=9 bytes_invalid=0 send_seq=6522 receive_seq=6522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94143 bytes_read=2484107 bytes_retransmit=0 bytes_invalid=0 send_seq=11081 receive_seq=11081 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998675 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.5 th2: temp=62.2 th3: temp=59.7 sysload=0.43 cputime=475.458 memavail=7393176 print_time=6366.845 buffer_time=1.959 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6343.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29189902 bytes_read=4569880 bytes_retransmit=9 bytes_invalid=0 send_seq=552045 receive_seq=552045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400015958 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39304 bytes_read=123037 bytes_retransmit=0 bytes_invalid=0 send_seq=6522 receive_seq=6522 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999608 adj=49997592 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192436 bytes_read=6132029 bytes_retransmit=9 bytes_invalid=0 send_seq=26776 receive_seq=26776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997703 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125858 bytes_read=3316536 bytes_retransmit=9 bytes_invalid=0 send_seq=17363 receive_seq=17363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39571 bytes_read=1619360 bytes_retransmit=9 bytes_invalid=0 send_seq=6536 receive_seq=6536 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999566 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40057 bytes_read=120628 bytes_retransmit=9 bytes_invalid=0 send_seq=6523 receive_seq=6523 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94149 bytes_read=2484463 bytes_retransmit=0 bytes_invalid=0 send_seq=11082 receive_seq=11082 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998647 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.4 th2: temp=62.2 th3: temp=59.7 sysload=0.43 cputime=475.541 memavail=7395056 print_time=6366.845 buffer_time=0.959 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6344.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29190240 bytes_read=4570332 bytes_retransmit=9 bytes_invalid=0 send_seq=552068 receive_seq=552068 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015944 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39310 bytes_read=123053 bytes_retransmit=0 bytes_invalid=0 send_seq=6523 receive_seq=6523 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999608 adj=49997581 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192442 bytes_read=6132143 bytes_retransmit=9 bytes_invalid=0 send_seq=26777 receive_seq=26777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997692 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=125927 bytes_read=3319571 bytes_retransmit=9 bytes_invalid=0 send_seq=17373 receive_seq=17373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39577 bytes_read=1619609 bytes_retransmit=9 bytes_invalid=0 send_seq=6537 receive_seq=6537 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999565 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40063 bytes_read=120644 bytes_retransmit=9 bytes_invalid=0 send_seq=6524 receive_seq=6524 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94155 bytes_read=2484819 bytes_retransmit=0 bytes_invalid=0 send_seq=11083 receive_seq=11083 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998649 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.3 th2: temp=62.2 th3: temp=59.7 sysload=0.43 cputime=475.605 memavail=7393560 print_time=6366.845 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
LIS2DW finished 'toolboard_t1' measurements
Resonances data written to /tmp/resonances_x_125.000_250.000_20.000_t1_copy.csv file
Probing point (125.000, 250.000, 20.000)
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t1' measurements
toolhead: max_velocity: 600.000000
max_accel: 8379.841000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance testing
Testing frequency 10 Hz
Stats 6345.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29190731 bytes_read=4570767 bytes_retransmit=9 bytes_invalid=0 send_seq=552094 receive_seq=552094 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015963 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39316 bytes_read=123069 bytes_retransmit=0 bytes_invalid=0 send_seq=6524 receive_seq=6524 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997601 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192448 bytes_read=6132271 bytes_retransmit=9 bytes_invalid=0 send_seq=26778 receive_seq=26778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997693 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=126097 bytes_read=3324892 bytes_retransmit=9 bytes_invalid=0 send_seq=17391 receive_seq=17391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997471 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39583 bytes_read=1619903 bytes_retransmit=9 bytes_invalid=0 send_seq=6538 receive_seq=6538 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40069 bytes_read=120660 bytes_retransmit=9 bytes_invalid=0 send_seq=6525 receive_seq=6525 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94161 bytes_read=2485175 bytes_retransmit=0 bytes_invalid=0 send_seq=11084 receive_seq=11084 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998659 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.5 th2: temp=62.2 th3: temp=59.7 sysload=0.39 cputime=475.900 memavail=7397312 print_time=6368.594 buffer_time=0.694 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 11 Hz
Testing frequency 12 Hz
Stats 6346.2: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29200349 bytes_read=4571947 bytes_retransmit=9 bytes_invalid=0 send_seq=552268 receive_seq=552268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015978 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39322 bytes_read=123098 bytes_retransmit=0 bytes_invalid=0 send_seq=6525 receive_seq=6525 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999608 adj=49997576 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192454 bytes_read=6132371 bytes_retransmit=9 bytes_invalid=0 send_seq=26779 receive_seq=26779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997640 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=126173 bytes_read=3327892 bytes_retransmit=9 bytes_invalid=0 send_seq=17402 receive_seq=17402 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997391 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39589 bytes_read=1620137 bytes_retransmit=9 bytes_invalid=0 send_seq=6539 receive_seq=6539 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997616 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40075 bytes_read=120676 bytes_retransmit=9 bytes_invalid=0 send_seq=6526 receive_seq=6526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94167 bytes_read=2485531 bytes_retransmit=0 bytes_invalid=0 send_seq=11085 receive_seq=11085 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998635 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.4 th2: temp=62.3 th3: temp=59.7 sysload=0.39 cputime=476.021 memavail=7397312 print_time=6370.968 buffer_time=2.067 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 13 Hz
Stats 6347.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=29205121 bytes_read=4572772 bytes_retransmit=9 bytes_invalid=0 send_seq=552362 receive_seq=552362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=298 freq=400015995 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39328 bytes_read=123114 bytes_retransmit=0 bytes_invalid=0 send_seq=6526 receive_seq=6526 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997572 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192460 bytes_read=6132485 bytes_retransmit=9 bytes_invalid=0 send_seq=26780 receive_seq=26780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997683 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=126249 bytes_read=3330895 bytes_retransmit=9 bytes_invalid=0 send_seq=17413 receive_seq=17413 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39595 bytes_read=1620371 bytes_retransmit=9 bytes_invalid=0 send_seq=6540 receive_seq=6540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997607 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40081 bytes_read=120703 bytes_retransmit=9 bytes_invalid=0 send_seq=6527 receive_seq=6527 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94173 bytes_read=2485887 bytes_retransmit=0 bytes_invalid=0 send_seq=11086 receive_seq=11086 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998628 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.2 th2: temp=62.3 th3: temp=59.6 sysload=0.39 cputime=476.114 memavail=7396344 print_time=6372.148 buffer_time=2.246 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 14 Hz
Stats 6348.2: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=29209673 bytes_read=4573502 bytes_retransmit=9 bytes_invalid=0 send_seq=552446 receive_seq=552446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=40 freq=400015996 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39334 bytes_read=123130 bytes_retransmit=0 bytes_invalid=0 send_seq=6527 receive_seq=6527 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999608 adj=49997567 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192466 bytes_read=6132599 bytes_retransmit=9 bytes_invalid=0 send_seq=26781 receive_seq=26781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997625 toolboard_t1: mcu_awake=0.364 mcu_task_avg=0.000125 mcu_task_stddev=0.000065 bytes_write=126325 bytes_read=3333997 bytes_retransmit=9 bytes_invalid=0 send_seq=17424 receive_seq=17424 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997441 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39601 bytes_read=1620665 bytes_retransmit=9 bytes_invalid=0 send_seq=6541 receive_seq=6541 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997579 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40087 bytes_read=120719 bytes_retransmit=9 bytes_invalid=0 send_seq=6528 receive_seq=6528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999425 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94179 bytes_read=2486243 bytes_retransmit=0 bytes_invalid=0 send_seq=11087 receive_seq=11087 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998615 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.5 th2: temp=62.2 th3: temp=59.7 sysload=0.39 cputime=476.205 memavail=7396344 print_time=6373.095 buffer_time=2.193 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 15 Hz
Stats 6349.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=29213778 bytes_read=4574222 bytes_retransmit=9 bytes_invalid=0 send_seq=552528 receive_seq=552528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=1059 freq=400015976 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39340 bytes_read=123146 bytes_retransmit=0 bytes_invalid=0 send_seq=6528 receive_seq=6528 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999610 adj=49997566 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192472 bytes_read=6132713 bytes_retransmit=9 bytes_invalid=0 send_seq=26782 receive_seq=26782 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997676 toolboard_t1: mcu_awake=0.364 mcu_task_avg=0.000125 mcu_task_stddev=0.000065 bytes_write=126401 bytes_read=3337053 bytes_retransmit=9 bytes_invalid=0 send_seq=17435 receive_seq=17435 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997413 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39607 bytes_read=1620914 bytes_retransmit=9 bytes_invalid=0 send_seq=6542 receive_seq=6542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997581 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40093 bytes_read=120735 bytes_retransmit=9 bytes_invalid=0 send_seq=6529 receive_seq=6529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999425 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94185 bytes_read=2486599 bytes_retransmit=0 bytes_invalid=0 send_seq=11088 receive_seq=11088 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998642 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.1 th2: temp=62.2 th3: temp=59.6 sysload=0.39 cputime=476.293 memavail=7396344 print_time=6374.032 buffer_time=2.130 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 16 Hz
Stats 6350.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=29218667 bytes_read=4575031 bytes_retransmit=9 bytes_invalid=0 send_seq=552622 receive_seq=552622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=295 freq=400015975 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39346 bytes_read=123162 bytes_retransmit=0 bytes_invalid=0 send_seq=6529 receive_seq=6529 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999609 adj=49997620 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192478 bytes_read=6132827 bytes_retransmit=9 bytes_invalid=0 send_seq=26783 receive_seq=26783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997692 toolboard_t1: mcu_awake=0.364 mcu_task_avg=0.000125 mcu_task_stddev=0.000065 bytes_write=126477 bytes_read=3340168 bytes_retransmit=9 bytes_invalid=0 send_seq=17446 receive_seq=17446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997437 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39613 bytes_read=1621148 bytes_retransmit=9 bytes_invalid=0 send_seq=6543 receive_seq=6543 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40099 bytes_read=120751 bytes_retransmit=9 bytes_invalid=0 send_seq=6530 receive_seq=6530 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94191 bytes_read=2486955 bytes_retransmit=0 bytes_invalid=0 send_seq=11089 receive_seq=11089 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998666 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.4 th2: temp=62.2 th3: temp=59.5 sysload=0.36 cputime=476.386 memavail=7396344 print_time=6374.947 buffer_time=2.044 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 17 Hz
Stats 6351.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=29224022 bytes_read=4575841 bytes_retransmit=9 bytes_invalid=0 send_seq=552722 receive_seq=552722 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=1152 freq=400015985 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39352 bytes_read=123191 bytes_retransmit=0 bytes_invalid=0 send_seq=6530 receive_seq=6530 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999608 adj=49997613 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192484 bytes_read=6132941 bytes_retransmit=9 bytes_invalid=0 send_seq=26784 receive_seq=26784 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997665 toolboard_t1: mcu_awake=0.364 mcu_task_avg=0.000125 mcu_task_stddev=0.000065 bytes_write=126553 bytes_read=3343252 bytes_retransmit=9 bytes_invalid=0 send_seq=17457 receive_seq=17457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997545 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39619 bytes_read=1621442 bytes_retransmit=9 bytes_invalid=0 send_seq=6544 receive_seq=6544 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40105 bytes_read=120767 bytes_retransmit=9 bytes_invalid=0 send_seq=6531 receive_seq=6531 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94197 bytes_read=2487311 bytes_retransmit=0 bytes_invalid=0 send_seq=11090 receive_seq=11090 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998665 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.4 th2: temp=62.2 th3: temp=59.5 sysload=0.36 cputime=476.487 memavail=7396344 print_time=6376.130 buffer_time=2.227 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 18 Hz
Stats 6352.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=29228435 bytes_read=4576597 bytes_retransmit=9 bytes_invalid=0 send_seq=552808 receive_seq=552808 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=52 upcoming_bytes=2404 freq=400015993 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39358 bytes_read=123207 bytes_retransmit=0 bytes_invalid=0 send_seq=6531 receive_seq=6531 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999608 adj=49997589 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192490 bytes_read=6133034 bytes_retransmit=9 bytes_invalid=0 send_seq=26785 receive_seq=26785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997626 toolboard_t1: mcu_awake=0.364 mcu_task_avg=0.000125 mcu_task_stddev=0.000065 bytes_write=126629 bytes_read=3346293 bytes_retransmit=9 bytes_invalid=0 send_seq=17468 receive_seq=17468 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39625 bytes_read=1621676 bytes_retransmit=9 bytes_invalid=0 send_seq=6545 receive_seq=6545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997607 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40111 bytes_read=120794 bytes_retransmit=9 bytes_invalid=0 send_seq=6532 receive_seq=6532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94203 bytes_read=2487667 bytes_retransmit=0 bytes_invalid=0 send_seq=11091 receive_seq=11091 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998706 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.6 th2: temp=62.0 th3: temp=59.5 sysload=0.36 cputime=476.578 memavail=7396344 print_time=6377.075 buffer_time=2.172 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 19 Hz
Stats 6353.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=29234051 bytes_read=4577461 bytes_retransmit=9 bytes_invalid=0 send_seq=552913 receive_seq=552913 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=1700 freq=400015996 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39364 bytes_read=123223 bytes_retransmit=0 bytes_invalid=0 send_seq=6532 receive_seq=6532 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999607 adj=49997573 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192496 bytes_read=6133140 bytes_retransmit=9 bytes_invalid=0 send_seq=26786 receive_seq=26786 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997610 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=126705 bytes_read=3349348 bytes_retransmit=9 bytes_invalid=0 send_seq=17479 receive_seq=17479 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997475 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39631 bytes_read=1621910 bytes_retransmit=9 bytes_invalid=0 send_seq=6546 receive_seq=6546 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997591 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40117 bytes_read=120810 bytes_retransmit=9 bytes_invalid=0 send_seq=6533 receive_seq=6533 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94209 bytes_read=2488023 bytes_retransmit=0 bytes_invalid=0 send_seq=11092 receive_seq=11092 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998682 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.6 th2: temp=62.0 th3: temp=59.4 sysload=0.36 cputime=476.675 memavail=7396352 print_time=6378.014 buffer_time=2.110 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 20 Hz
Stats 6354.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=29239992 bytes_read=4578326 bytes_retransmit=9 bytes_invalid=0 send_seq=553024 receive_seq=553024 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=2735 freq=400016023 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39370 bytes_read=123239 bytes_retransmit=0 bytes_invalid=0 send_seq=6533 receive_seq=6533 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999606 adj=49997559 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192502 bytes_read=6133260 bytes_retransmit=9 bytes_invalid=0 send_seq=26787 receive_seq=26787 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997589 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=126781 bytes_read=3352413 bytes_retransmit=9 bytes_invalid=0 send_seq=17490 receive_seq=17490 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997446 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39637 bytes_read=1622219 bytes_retransmit=9 bytes_invalid=0 send_seq=6547 receive_seq=6547 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997588 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40123 bytes_read=120826 bytes_retransmit=9 bytes_invalid=0 send_seq=6534 receive_seq=6534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94215 bytes_read=2488379 bytes_retransmit=0 bytes_invalid=0 send_seq=11093 receive_seq=11093 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998666 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.3 th2: temp=61.9 th3: temp=59.4 sysload=0.36 cputime=476.779 memavail=7396100 print_time=6379.227 buffer_time=2.323 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 21 Hz
Stats 6355.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=29245140 bytes_read=4579114 bytes_retransmit=9 bytes_invalid=0 send_seq=553120 receive_seq=553120 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=3456 freq=400016052 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39376 bytes_read=123255 bytes_retransmit=0 bytes_invalid=0 send_seq=6534 receive_seq=6534 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999605 adj=49997522 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192508 bytes_read=6133353 bytes_retransmit=9 bytes_invalid=0 send_seq=26788 receive_seq=26788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997542 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=126850 bytes_read=3355433 bytes_retransmit=9 bytes_invalid=0 send_seq=17500 receive_seq=17500 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997384 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39643 bytes_read=1622453 bytes_retransmit=9 bytes_invalid=0 send_seq=6548 receive_seq=6548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997556 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40129 bytes_read=120842 bytes_retransmit=9 bytes_invalid=0 send_seq=6535 receive_seq=6535 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999420 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94221 bytes_read=2488735 bytes_retransmit=0 bytes_invalid=0 send_seq=11094 receive_seq=11094 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998631 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.4 th2: temp=61.9 th3: temp=59.2 sysload=0.33 cputime=476.872 memavail=7396104 print_time=6380.083 buffer_time=2.179 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 22 Hz
Stats 6356.3: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=29251320 bytes_read=4580021 bytes_retransmit=9 bytes_invalid=0 send_seq=553234 receive_seq=553234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=2523 freq=400016034 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39382 bytes_read=123284 bytes_retransmit=0 bytes_invalid=0 send_seq=6535 receive_seq=6535 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999605 adj=49997479 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192514 bytes_read=6133465 bytes_retransmit=9 bytes_invalid=0 send_seq=26789 receive_seq=26789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997510 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=126926 bytes_read=3358483 bytes_retransmit=9 bytes_invalid=0 send_seq=17511 receive_seq=17511 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997317 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39649 bytes_read=1622687 bytes_retransmit=9 bytes_invalid=0 send_seq=6549 receive_seq=6549 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997511 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40135 bytes_read=120858 bytes_retransmit=9 bytes_invalid=0 send_seq=6536 receive_seq=6536 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999409 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94227 bytes_read=2489091 bytes_retransmit=0 bytes_invalid=0 send_seq=11095 receive_seq=11095 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998611 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.7 th2: temp=61.8 th3: temp=59.3 sysload=0.33 cputime=476.970 memavail=7396132 print_time=6381.029 buffer_time=2.125 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 23 Hz
Stats 6357.3: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29257658 bytes_read=4580937 bytes_retransmit=9 bytes_invalid=0 send_seq=553352 receive_seq=553352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=3948 freq=400016011 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39388 bytes_read=123300 bytes_retransmit=0 bytes_invalid=0 send_seq=6536 receive_seq=6536 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999604 adj=49997524 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192520 bytes_read=6133579 bytes_retransmit=9 bytes_invalid=0 send_seq=26790 receive_seq=26790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997546 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127002 bytes_read=3361567 bytes_retransmit=9 bytes_invalid=0 send_seq=17522 receive_seq=17522 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997351 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39655 bytes_read=1622981 bytes_retransmit=9 bytes_invalid=0 send_seq=6550 receive_seq=6550 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997559 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40141 bytes_read=120885 bytes_retransmit=9 bytes_invalid=0 send_seq=6537 receive_seq=6537 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999421 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94233 bytes_read=2489447 bytes_retransmit=0 bytes_invalid=0 send_seq=11096 receive_seq=11096 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998632 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.5 th2: temp=61.7 th3: temp=59.2 sysload=0.33 cputime=477.080 memavail=7395136 print_time=6382.260 buffer_time=2.356 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 24 Hz
Stats 6358.3: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29263126 bytes_read=4581762 bytes_retransmit=9 bytes_invalid=0 send_seq=553455 receive_seq=553455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=4739 freq=400016007 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39394 bytes_read=123316 bytes_retransmit=0 bytes_invalid=0 send_seq=6537 receive_seq=6537 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999604 adj=49997566 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192526 bytes_read=6133679 bytes_retransmit=9 bytes_invalid=0 send_seq=26791 receive_seq=26791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997603 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127078 bytes_read=3364699 bytes_retransmit=9 bytes_invalid=0 send_seq=17533 receive_seq=17533 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997411 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39661 bytes_read=1623215 bytes_retransmit=9 bytes_invalid=0 send_seq=6551 receive_seq=6551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997604 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40147 bytes_read=120901 bytes_retransmit=9 bytes_invalid=0 send_seq=6538 receive_seq=6538 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94239 bytes_read=2489803 bytes_retransmit=0 bytes_invalid=0 send_seq=11097 receive_seq=11097 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998658 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.5 th2: temp=61.6 th3: temp=59.1 sysload=0.33 cputime=477.186 memavail=7394752 print_time=6383.108 buffer_time=2.203 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 25 Hz
Stats 6359.3: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29269983 bytes_read=4582721 bytes_retransmit=9 bytes_invalid=0 send_seq=553579 receive_seq=553579 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=3816 freq=400016004 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39400 bytes_read=123332 bytes_retransmit=0 bytes_invalid=0 send_seq=6538 receive_seq=6538 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999604 adj=49997583 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192532 bytes_read=6133807 bytes_retransmit=9 bytes_invalid=0 send_seq=26792 receive_seq=26792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997620 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127154 bytes_read=3367757 bytes_retransmit=9 bytes_invalid=0 send_seq=17544 receive_seq=17544 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997405 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39667 bytes_read=1623464 bytes_retransmit=9 bytes_invalid=0 send_seq=6552 receive_seq=6552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997602 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40153 bytes_read=120917 bytes_retransmit=9 bytes_invalid=0 send_seq=6539 receive_seq=6539 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94245 bytes_read=2490159 bytes_retransmit=0 bytes_invalid=0 send_seq=11098 receive_seq=11098 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998662 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.5 th2: temp=61.5 th3: temp=59.0 sysload=0.33 cputime=477.288 memavail=7394752 print_time=6384.071 buffer_time=2.165 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 26 Hz
Stats 6360.3: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29276969 bytes_read=4583676 bytes_retransmit=9 bytes_invalid=0 send_seq=553708 receive_seq=553708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=3372 freq=400015994 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39406 bytes_read=123348 bytes_retransmit=0 bytes_invalid=0 send_seq=6539 receive_seq=6539 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999603 adj=49997588 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192538 bytes_read=6133921 bytes_retransmit=9 bytes_invalid=0 send_seq=26793 receive_seq=26793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997611 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127230 bytes_read=3370843 bytes_retransmit=9 bytes_invalid=0 send_seq=17555 receive_seq=17555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997417 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39673 bytes_read=1623758 bytes_retransmit=9 bytes_invalid=0 send_seq=6553 receive_seq=6553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997601 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40159 bytes_read=120933 bytes_retransmit=9 bytes_invalid=0 send_seq=6540 receive_seq=6540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94251 bytes_read=2490515 bytes_retransmit=0 bytes_invalid=0 send_seq=11099 receive_seq=11099 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998659 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.3 th2: temp=61.5 th3: temp=58.9 sysload=0.31 cputime=477.387 memavail=7394752 print_time=6384.939 buffer_time=2.033 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 27 Hz
Stats 6361.3: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29282896 bytes_read=4584536 bytes_retransmit=9 bytes_invalid=0 send_seq=553818 receive_seq=553818 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=4012 freq=400015992 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=39412 bytes_read=123377 bytes_retransmit=0 bytes_invalid=0 send_seq=6540 receive_seq=6540 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999603 adj=49997597 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192544 bytes_read=6134021 bytes_retransmit=9 bytes_invalid=0 send_seq=26794 receive_seq=26794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997616 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127306 bytes_read=3373900 bytes_retransmit=9 bytes_invalid=0 send_seq=17566 receive_seq=17566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997422 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39679 bytes_read=1623992 bytes_retransmit=9 bytes_invalid=0 send_seq=6554 receive_seq=6554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997612 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40165 bytes_read=120949 bytes_retransmit=9 bytes_invalid=0 send_seq=6541 receive_seq=6541 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94257 bytes_read=2490871 bytes_retransmit=0 bytes_invalid=0 send_seq=11100 receive_seq=11100 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998660 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.4 th2: temp=61.5 th3: temp=59.0 sysload=0.31 cputime=477.486 memavail=7394536 print_time=6385.909 buffer_time=2.003 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 28 Hz
Stats 6362.3: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29290135 bytes_read=4585551 bytes_retransmit=9 bytes_invalid=0 send_seq=553950 receive_seq=553950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=5399 freq=400015970 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=39418 bytes_read=123393 bytes_retransmit=0 bytes_invalid=0 send_seq=6541 receive_seq=6541 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999601 adj=49997591 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192550 bytes_read=6134135 bytes_retransmit=9 bytes_invalid=0 send_seq=26795 receive_seq=26795 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997608 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127382 bytes_read=3376957 bytes_retransmit=9 bytes_invalid=0 send_seq=17577 receive_seq=17577 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997414 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39685 bytes_read=1624226 bytes_retransmit=9 bytes_invalid=0 send_seq=6555 receive_seq=6555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40171 bytes_read=120976 bytes_retransmit=9 bytes_invalid=0 send_seq=6542 receive_seq=6542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94263 bytes_read=2491227 bytes_retransmit=0 bytes_invalid=0 send_seq=11101 receive_seq=11101 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998654 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.5 th2: temp=61.4 th3: temp=58.7 sysload=0.31 cputime=477.595 memavail=7394536 print_time=6387.128 buffer_time=2.221 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 29 Hz
Stats 6363.3: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29297469 bytes_read=4586536 bytes_retransmit=9 bytes_invalid=0 send_seq=554085 receive_seq=554085 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=4232 freq=400015963 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=39424 bytes_read=123409 bytes_retransmit=0 bytes_invalid=0 send_seq=6542 receive_seq=6542 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999601 adj=49997613 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192556 bytes_read=6134249 bytes_retransmit=9 bytes_invalid=0 send_seq=26796 receive_seq=26796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997733 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127458 bytes_read=3380060 bytes_retransmit=9 bytes_invalid=0 send_seq=17588 receive_seq=17588 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997461 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=39691 bytes_read=1624520 bytes_retransmit=9 bytes_invalid=0 send_seq=6556 receive_seq=6556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40177 bytes_read=120992 bytes_retransmit=9 bytes_invalid=0 send_seq=6543 receive_seq=6543 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94269 bytes_read=2491583 bytes_retransmit=0 bytes_invalid=0 send_seq=11102 receive_seq=11102 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998669 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.4 th2: temp=61.3 th3: temp=58.9 sysload=0.31 cputime=477.698 memavail=7394536 print_time=6388.000 buffer_time=2.093 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 30 Hz
Stats 6364.3: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29303634 bytes_read=4587416 bytes_retransmit=9 bytes_invalid=0 send_seq=554199 receive_seq=554199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=29 upcoming_bytes=5096 freq=400015962 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=39430 bytes_read=123425 bytes_retransmit=0 bytes_invalid=0 send_seq=6543 receive_seq=6543 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999600 adj=49997619 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192562 bytes_read=6134349 bytes_retransmit=9 bytes_invalid=0 send_seq=26797 receive_seq=26797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997765 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127534 bytes_read=3383116 bytes_retransmit=9 bytes_invalid=0 send_seq=17599 receive_seq=17599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997477 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39697 bytes_read=1624769 bytes_retransmit=9 bytes_invalid=0 send_seq=6557 receive_seq=6557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40183 bytes_read=121008 bytes_retransmit=9 bytes_invalid=0 send_seq=6544 receive_seq=6544 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94275 bytes_read=2491939 bytes_retransmit=0 bytes_invalid=0 send_seq=11103 receive_seq=11103 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998667 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.5 th2: temp=61.3 th3: temp=58.9 sysload=0.31 cputime=477.799 memavail=7394540 print_time=6388.930 buffer_time=2.023 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 31 Hz
Stats 6365.3: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29311310 bytes_read=4588450 bytes_retransmit=9 bytes_invalid=0 send_seq=554338 receive_seq=554338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=35 upcoming_bytes=6432 freq=400015950 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=39436 bytes_read=123440 bytes_retransmit=0 bytes_invalid=0 send_seq=6544 receive_seq=6544 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999600 adj=49997611 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192568 bytes_read=6134477 bytes_retransmit=9 bytes_invalid=0 send_seq=26798 receive_seq=26798 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997727 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127610 bytes_read=3386173 bytes_retransmit=9 bytes_invalid=0 send_seq=17610 receive_seq=17610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997494 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39703 bytes_read=1625003 bytes_retransmit=9 bytes_invalid=0 send_seq=6558 receive_seq=6558 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40189 bytes_read=121024 bytes_retransmit=9 bytes_invalid=0 send_seq=6545 receive_seq=6545 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94281 bytes_read=2492295 bytes_retransmit=0 bytes_invalid=0 send_seq=11104 receive_seq=11104 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998671 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.5 th2: temp=61.3 th3: temp=58.8 sysload=0.28 cputime=477.912 memavail=7394540 print_time=6390.151 buffer_time=2.244 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 32 Hz
Stats 6366.3: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29319064 bytes_read=4589461 bytes_retransmit=9 bytes_invalid=0 send_seq=554479 receive_seq=554479 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=4984 freq=400015937 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39442 bytes_read=123468 bytes_retransmit=0 bytes_invalid=0 send_seq=6545 receive_seq=6545 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999600 adj=49997625 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192574 bytes_read=6134591 bytes_retransmit=9 bytes_invalid=0 send_seq=26799 receive_seq=26799 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997810 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127686 bytes_read=3389318 bytes_retransmit=9 bytes_invalid=0 send_seq=17621 receive_seq=17621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997507 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39709 bytes_read=1625297 bytes_retransmit=9 bytes_invalid=0 send_seq=6559 receive_seq=6559 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40195 bytes_read=121040 bytes_retransmit=9 bytes_invalid=0 send_seq=6546 receive_seq=6546 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94287 bytes_read=2492651 bytes_retransmit=0 bytes_invalid=0 send_seq=11105 receive_seq=11105 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998679 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.4 th2: temp=61.1 th3: temp=59.0 sysload=0.28 cputime=478.019 memavail=7394540 print_time=6391.035 buffer_time=2.127 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 33 Hz
Stats 6367.3: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29325605 bytes_read=4590372 bytes_retransmit=9 bytes_invalid=0 send_seq=554596 receive_seq=554596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=6204 freq=400015940 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39448 bytes_read=123483 bytes_retransmit=0 bytes_invalid=0 send_seq=6546 receive_seq=6546 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999599 adj=49997635 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192580 bytes_read=6134691 bytes_retransmit=9 bytes_invalid=0 send_seq=26800 receive_seq=26800 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997800 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127762 bytes_read=3392374 bytes_retransmit=9 bytes_invalid=0 send_seq=17632 receive_seq=17632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997639 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39715 bytes_read=1625531 bytes_retransmit=9 bytes_invalid=0 send_seq=6560 receive_seq=6560 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997679 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40201 bytes_read=121067 bytes_retransmit=9 bytes_invalid=0 send_seq=6547 receive_seq=6547 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94293 bytes_read=2493007 bytes_retransmit=0 bytes_invalid=0 send_seq=11106 receive_seq=11106 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998685 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.4 th2: temp=61.2 th3: temp=58.8 sysload=0.28 cputime=478.121 memavail=7394308 print_time=6391.978 buffer_time=2.068 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 34 Hz
Stats 6368.3: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29333708 bytes_read=4591451 bytes_retransmit=9 bytes_invalid=0 send_seq=554744 receive_seq=554744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=7540 freq=400015939 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39454 bytes_read=123498 bytes_retransmit=0 bytes_invalid=0 send_seq=6547 receive_seq=6547 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999599 adj=49997623 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192586 bytes_read=6134805 bytes_retransmit=9 bytes_invalid=0 send_seq=26801 receive_seq=26801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997755 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127838 bytes_read=3395448 bytes_retransmit=9 bytes_invalid=0 send_seq=17643 receive_seq=17643 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997588 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39721 bytes_read=1625765 bytes_retransmit=9 bytes_invalid=0 send_seq=6561 receive_seq=6561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40207 bytes_read=121083 bytes_retransmit=9 bytes_invalid=0 send_seq=6548 receive_seq=6548 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94299 bytes_read=2493363 bytes_retransmit=0 bytes_invalid=0 send_seq=11107 receive_seq=11107 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998685 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.4 th2: temp=61.1 th3: temp=58.7 sysload=0.28 cputime=478.235 memavail=7394312 print_time=6393.185 buffer_time=2.275 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 35 Hz
Stats 6369.3: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29341707 bytes_read=4592466 bytes_retransmit=9 bytes_invalid=0 send_seq=554885 receive_seq=554885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=5973 freq=400015935 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39460 bytes_read=123513 bytes_retransmit=0 bytes_invalid=0 send_seq=6548 receive_seq=6548 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999597 adj=49997611 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192592 bytes_read=6134919 bytes_retransmit=9 bytes_invalid=0 send_seq=26802 receive_seq=26802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997712 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127907 bytes_read=3398510 bytes_retransmit=9 bytes_invalid=0 send_seq=17653 receive_seq=17653 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997544 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39727 bytes_read=1626074 bytes_retransmit=9 bytes_invalid=0 send_seq=6562 receive_seq=6562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40213 bytes_read=121099 bytes_retransmit=9 bytes_invalid=0 send_seq=6549 receive_seq=6549 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94305 bytes_read=2493719 bytes_retransmit=0 bytes_invalid=0 send_seq=11108 receive_seq=11108 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998678 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.3 th2: temp=61.2 th3: temp=58.8 sysload=0.28 cputime=478.340 memavail=7394312 print_time=6394.042 buffer_time=2.132 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 36 Hz
Stats 6370.3: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29348610 bytes_read=4593411 bytes_retransmit=9 bytes_invalid=0 send_seq=555012 receive_seq=555012 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=7420 freq=400015926 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39466 bytes_read=123529 bytes_retransmit=0 bytes_invalid=0 send_seq=6549 receive_seq=6549 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999596 adj=49997595 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192598 bytes_read=6135033 bytes_retransmit=9 bytes_invalid=0 send_seq=26803 receive_seq=26803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997702 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=127983 bytes_read=3401569 bytes_retransmit=9 bytes_invalid=0 send_seq=17664 receive_seq=17664 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39733 bytes_read=1626308 bytes_retransmit=9 bytes_invalid=0 send_seq=6563 receive_seq=6563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40219 bytes_read=121115 bytes_retransmit=9 bytes_invalid=0 send_seq=6550 receive_seq=6550 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94311 bytes_read=2494075 bytes_retransmit=0 bytes_invalid=0 send_seq=11109 receive_seq=11109 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998679 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=55.9 th1: temp=55.5 th2: temp=61.2 th3: temp=58.8 sysload=0.26 cputime=478.444 memavail=7394312 print_time=6395.003 buffer_time=2.092 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 37 Hz
Stats 6371.3: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29357274 bytes_read=4594530 bytes_retransmit=9 bytes_invalid=0 send_seq=555168 receive_seq=555168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=8796 freq=400015923 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39472 bytes_read=123558 bytes_retransmit=0 bytes_invalid=0 send_seq=6550 receive_seq=6550 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999596 adj=49997603 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192604 bytes_read=6135147 bytes_retransmit=9 bytes_invalid=0 send_seq=26804 receive_seq=26804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997693 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=128059 bytes_read=3404626 bytes_retransmit=9 bytes_invalid=0 send_seq=17675 receive_seq=17675 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997515 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39739 bytes_read=1626542 bytes_retransmit=9 bytes_invalid=0 send_seq=6564 receive_seq=6564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40225 bytes_read=121131 bytes_retransmit=9 bytes_invalid=0 send_seq=6551 receive_seq=6551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999447 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94317 bytes_read=2494431 bytes_retransmit=0 bytes_invalid=0 send_seq=11110 receive_seq=11110 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998686 coil_temp=16.9 refs=0 mcu_temp=20.25 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.5 th2: temp=61.5 th3: temp=58.8 sysload=0.26 cputime=478.561 memavail=7394312 print_time=6396.213 buffer_time=2.302 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 38 Hz
Stats 6372.3: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29365855 bytes_read=4595636 bytes_retransmit=9 bytes_invalid=0 send_seq=555324 receive_seq=555324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=36 upcoming_bytes=7061 freq=400015911 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39478 bytes_read=123574 bytes_retransmit=0 bytes_invalid=0 send_seq=6551 receive_seq=6551 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999596 adj=49997606 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192610 bytes_read=6135261 bytes_retransmit=9 bytes_invalid=0 send_seq=26805 receive_seq=26805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997672 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=128135 bytes_read=3407710 bytes_retransmit=9 bytes_invalid=0 send_seq=17686 receive_seq=17686 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39745 bytes_read=1626836 bytes_retransmit=9 bytes_invalid=0 send_seq=6565 receive_seq=6565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40231 bytes_read=121158 bytes_retransmit=9 bytes_invalid=0 send_seq=6552 receive_seq=6552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94323 bytes_read=2494787 bytes_retransmit=0 bytes_invalid=0 send_seq=11111 receive_seq=11111 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998675 coil_temp=16.9 refs=0 mcu_temp=20.25 supply_voltage=3.012 th0: temp=56.1 th1: temp=55.4 th2: temp=61.0 th3: temp=58.8 sysload=0.26 cputime=478.670 memavail=7394312 print_time=6397.074 buffer_time=2.163 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 39 Hz
Stats 6373.3: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29373210 bytes_read=4596601 bytes_retransmit=9 bytes_invalid=0 send_seq=555455 receive_seq=555455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=8208 freq=400015897 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39484 bytes_read=123590 bytes_retransmit=0 bytes_invalid=0 send_seq=6552 receive_seq=6552 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999595 adj=49997621 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192616 bytes_read=6135361 bytes_retransmit=9 bytes_invalid=0 send_seq=26806 receive_seq=26806 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997761 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=128211 bytes_read=3410843 bytes_retransmit=9 bytes_invalid=0 send_seq=17697 receive_seq=17697 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39751 bytes_read=1627070 bytes_retransmit=9 bytes_invalid=0 send_seq=6566 receive_seq=6566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40237 bytes_read=121174 bytes_retransmit=9 bytes_invalid=0 send_seq=6553 receive_seq=6553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94329 bytes_read=2495143 bytes_retransmit=0 bytes_invalid=0 send_seq=11112 receive_seq=11112 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998680 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=56.4 th1: temp=55.5 th2: temp=61.0 th3: temp=58.6 sysload=0.26 cputime=478.780 memavail=7394316 print_time=6398.006 buffer_time=2.094 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 40 Hz
Stats 6374.3: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29382463 bytes_read=4597770 bytes_retransmit=9 bytes_invalid=0 send_seq=555621 receive_seq=555621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=9532 freq=400015902 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39490 bytes_read=123606 bytes_retransmit=0 bytes_invalid=0 send_seq=6553 receive_seq=6553 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999595 adj=49997633 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192622 bytes_read=6135475 bytes_retransmit=9 bytes_invalid=0 send_seq=26807 receive_seq=26807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997772 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=128287 bytes_read=3413914 bytes_retransmit=9 bytes_invalid=0 send_seq=17708 receive_seq=17708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997527 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39757 bytes_read=1627319 bytes_retransmit=9 bytes_invalid=0 send_seq=6567 receive_seq=6567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40243 bytes_read=121190 bytes_retransmit=9 bytes_invalid=0 send_seq=6554 receive_seq=6554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94335 bytes_read=2495499 bytes_retransmit=0 bytes_invalid=0 send_seq=11113 receive_seq=11113 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998693 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=56.3 th1: temp=55.4 th2: temp=61.1 th3: temp=58.8 sysload=0.26 cputime=478.902 memavail=7394316 print_time=6399.212 buffer_time=2.300 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 41 Hz
Stats 6375.3: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29391319 bytes_read=4598865 bytes_retransmit=9 bytes_invalid=0 send_seq=555778 receive_seq=555778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=8096 freq=400015904 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39496 bytes_read=123622 bytes_retransmit=0 bytes_invalid=0 send_seq=6554 receive_seq=6554 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999594 adj=49997618 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192628 bytes_read=6135603 bytes_retransmit=9 bytes_invalid=0 send_seq=26808 receive_seq=26808 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997716 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=128363 bytes_read=3416987 bytes_retransmit=9 bytes_invalid=0 send_seq=17719 receive_seq=17719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39763 bytes_read=1627613 bytes_retransmit=9 bytes_invalid=0 send_seq=6568 receive_seq=6568 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40249 bytes_read=121206 bytes_retransmit=9 bytes_invalid=0 send_seq=6555 receive_seq=6555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94341 bytes_read=2495855 bytes_retransmit=0 bytes_invalid=0 send_seq=11114 receive_seq=11114 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998706 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.5 th2: temp=61.2 th3: temp=58.6 sysload=0.32 cputime=479.025 memavail=7394952 print_time=6400.114 buffer_time=2.200 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 42 Hz
Stats 6376.3: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29398899 bytes_read=4599860 bytes_retransmit=9 bytes_invalid=0 send_seq=555915 receive_seq=555915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=9624 freq=400015930 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39502 bytes_read=123651 bytes_retransmit=0 bytes_invalid=0 send_seq=6555 receive_seq=6555 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999594 adj=49997607 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192634 bytes_read=6135703 bytes_retransmit=9 bytes_invalid=0 send_seq=26809 receive_seq=26809 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997689 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=128439 bytes_read=3420043 bytes_retransmit=9 bytes_invalid=0 send_seq=17730 receive_seq=17730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39769 bytes_read=1627847 bytes_retransmit=9 bytes_invalid=0 send_seq=6569 receive_seq=6569 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40255 bytes_read=121222 bytes_retransmit=9 bytes_invalid=0 send_seq=6556 receive_seq=6556 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94347 bytes_read=2496211 bytes_retransmit=0 bytes_invalid=0 send_seq=11115 receive_seq=11115 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998701 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.4 th2: temp=61.1 th3: temp=58.7 sysload=0.32 cputime=479.130 memavail=7394956 print_time=6401.032 buffer_time=2.118 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 43 Hz
Stats 6377.3: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29408733 bytes_read=4601071 bytes_retransmit=9 bytes_invalid=0 send_seq=556087 receive_seq=556087 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=7447 freq=400015921 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39508 bytes_read=123667 bytes_retransmit=0 bytes_invalid=0 send_seq=6556 receive_seq=6556 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999594 adj=49997561 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192640 bytes_read=6135817 bytes_retransmit=9 bytes_invalid=0 send_seq=26810 receive_seq=26810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997691 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=128515 bytes_read=3423114 bytes_retransmit=9 bytes_invalid=0 send_seq=17741 receive_seq=17741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997462 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39775 bytes_read=1628081 bytes_retransmit=9 bytes_invalid=0 send_seq=6570 receive_seq=6570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40261 bytes_read=121249 bytes_retransmit=9 bytes_invalid=0 send_seq=6557 receive_seq=6557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94353 bytes_read=2496567 bytes_retransmit=0 bytes_invalid=0 send_seq=11116 receive_seq=11116 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998668 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.5 th2: temp=61.1 th3: temp=58.6 sysload=0.32 cputime=479.244 memavail=7393976 print_time=6401.936 buffer_time=2.022 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 44 Hz
Stats 6378.3: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29418270 bytes_read=4602226 bytes_retransmit=9 bytes_invalid=0 send_seq=556256 receive_seq=556256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=8783 freq=400015944 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39514 bytes_read=123683 bytes_retransmit=0 bytes_invalid=0 send_seq=6557 receive_seq=6557 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999593 adj=49997579 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192646 bytes_read=6135931 bytes_retransmit=9 bytes_invalid=0 send_seq=26811 receive_seq=26811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997683 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=128591 bytes_read=3426202 bytes_retransmit=9 bytes_invalid=0 send_seq=17752 receive_seq=17752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997565 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39781 bytes_read=1628375 bytes_retransmit=9 bytes_invalid=0 send_seq=6571 receive_seq=6571 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40267 bytes_read=121265 bytes_retransmit=9 bytes_invalid=0 send_seq=6558 receive_seq=6558 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94359 bytes_read=2496923 bytes_retransmit=0 bytes_invalid=0 send_seq=11117 receive_seq=11117 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998669 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.4 th2: temp=61.0 th3: temp=58.7 sysload=0.32 cputime=479.364 memavail=7393980 print_time=6403.142 buffer_time=2.228 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 45 Hz
Stats 6379.3: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29426539 bytes_read=4603281 bytes_retransmit=9 bytes_invalid=0 send_seq=556405 receive_seq=556405 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=10108 freq=400015926 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39520 bytes_read=123699 bytes_retransmit=0 bytes_invalid=0 send_seq=6558 receive_seq=6558 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999593 adj=49997546 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192652 bytes_read=6136031 bytes_retransmit=9 bytes_invalid=0 send_seq=26812 receive_seq=26812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997614 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=128667 bytes_read=3429258 bytes_retransmit=9 bytes_invalid=0 send_seq=17763 receive_seq=17763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997485 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39787 bytes_read=1628624 bytes_retransmit=9 bytes_invalid=0 send_seq=6572 receive_seq=6572 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40273 bytes_read=121281 bytes_retransmit=9 bytes_invalid=0 send_seq=6559 receive_seq=6559 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94365 bytes_read=2497279 bytes_retransmit=0 bytes_invalid=0 send_seq=11118 receive_seq=11118 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998646 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.5 th2: temp=61.0 th3: temp=58.6 sysload=0.32 cputime=479.469 memavail=7393980 print_time=6404.059 buffer_time=2.145 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 46 Hz
Stats 6380.3: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29436254 bytes_read=4604490 bytes_retransmit=9 bytes_invalid=0 send_seq=556579 receive_seq=556579 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=8093 freq=400015906 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39526 bytes_read=123715 bytes_retransmit=0 bytes_invalid=0 send_seq=6559 receive_seq=6559 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999593 adj=49997577 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192658 bytes_read=6136159 bytes_retransmit=9 bytes_invalid=0 send_seq=26813 receive_seq=26813 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997650 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=128743 bytes_read=3432328 bytes_retransmit=9 bytes_invalid=0 send_seq=17774 receive_seq=17774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39793 bytes_read=1628858 bytes_retransmit=9 bytes_invalid=0 send_seq=6573 receive_seq=6573 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40279 bytes_read=121297 bytes_retransmit=9 bytes_invalid=0 send_seq=6560 receive_seq=6560 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94371 bytes_read=2497635 bytes_retransmit=0 bytes_invalid=0 send_seq=11119 receive_seq=11119 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998669 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.5 th2: temp=61.0 th3: temp=58.5 sysload=0.29 cputime=479.581 memavail=7393980 print_time=6404.953 buffer_time=2.038 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 47 Hz
Stats 6381.3: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29446317 bytes_read=4605695 bytes_retransmit=9 bytes_invalid=0 send_seq=556758 receive_seq=556758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=9116 freq=400015899 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=39532 bytes_read=123744 bytes_retransmit=0 bytes_invalid=0 send_seq=6560 receive_seq=6560 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999592 adj=49997609 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192664 bytes_read=6136273 bytes_retransmit=9 bytes_invalid=0 send_seq=26814 receive_seq=26814 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997698 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=128819 bytes_read=3435459 bytes_retransmit=9 bytes_invalid=0 send_seq=17785 receive_seq=17785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997530 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39799 bytes_read=1629152 bytes_retransmit=9 bytes_invalid=0 send_seq=6574 receive_seq=6574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40285 bytes_read=121313 bytes_retransmit=9 bytes_invalid=0 send_seq=6561 receive_seq=6561 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94377 bytes_read=2497991 bytes_retransmit=0 bytes_invalid=0 send_seq=11120 receive_seq=11120 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998684 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.5 th2: temp=61.1 th3: temp=58.6 sysload=0.29 cputime=479.704 memavail=7393980 print_time=6406.157 buffer_time=2.242 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 48 Hz
Stats 6382.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29454650 bytes_read=4606771 bytes_retransmit=9 bytes_invalid=0 send_seq=556908 receive_seq=556908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=10596 freq=400015887 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=39538 bytes_read=123760 bytes_retransmit=0 bytes_invalid=0 send_seq=6561 receive_seq=6561 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999592 adj=49997606 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192670 bytes_read=6136373 bytes_retransmit=9 bytes_invalid=0 send_seq=26815 receive_seq=26815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997688 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=128895 bytes_read=3438515 bytes_retransmit=9 bytes_invalid=0 send_seq=17796 receive_seq=17796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997521 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39805 bytes_read=1629386 bytes_retransmit=9 bytes_invalid=0 send_seq=6575 receive_seq=6575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997679 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40291 bytes_read=121340 bytes_retransmit=9 bytes_invalid=0 send_seq=6562 receive_seq=6562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94383 bytes_read=2498347 bytes_retransmit=0 bytes_invalid=0 send_seq=11121 receive_seq=11121 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998686 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.5 th2: temp=60.9 th3: temp=58.6 sysload=0.29 cputime=479.813 memavail=7393980 print_time=6407.074 buffer_time=2.158 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 49 Hz
Stats 6383.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29464567 bytes_read=4607995 bytes_retransmit=9 bytes_invalid=0 send_seq=557085 receive_seq=557085 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=8613 freq=400015891 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=39544 bytes_read=123776 bytes_retransmit=0 bytes_invalid=0 send_seq=6562 receive_seq=6562 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999591 adj=49997623 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192676 bytes_read=6136501 bytes_retransmit=9 bytes_invalid=0 send_seq=26816 receive_seq=26816 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997692 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=128971 bytes_read=3441603 bytes_retransmit=9 bytes_invalid=0 send_seq=17807 receive_seq=17807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997542 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39811 bytes_read=1629620 bytes_retransmit=9 bytes_invalid=0 send_seq=6576 receive_seq=6576 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40297 bytes_read=121356 bytes_retransmit=9 bytes_invalid=0 send_seq=6563 receive_seq=6563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94389 bytes_read=2498703 bytes_retransmit=0 bytes_invalid=0 send_seq=11122 receive_seq=11122 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998688 coil_temp=16.9 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.6 th2: temp=61.0 th3: temp=58.6 sysload=0.29 cputime=479.933 memavail=7393980 print_time=6407.978 buffer_time=2.062 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 50 Hz
Stats 6384.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29474760 bytes_read=4609220 bytes_retransmit=9 bytes_invalid=0 send_seq=557268 receive_seq=557268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=10056 freq=400015877 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=39550 bytes_read=123792 bytes_retransmit=0 bytes_invalid=0 send_seq=6563 receive_seq=6563 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999592 adj=49997610 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192682 bytes_read=6136601 bytes_retransmit=9 bytes_invalid=0 send_seq=26817 receive_seq=26817 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997692 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129040 bytes_read=3444654 bytes_retransmit=9 bytes_invalid=0 send_seq=17817 receive_seq=17817 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997513 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39817 bytes_read=1629929 bytes_retransmit=9 bytes_invalid=0 send_seq=6577 receive_seq=6577 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40303 bytes_read=121372 bytes_retransmit=9 bytes_invalid=0 send_seq=6564 receive_seq=6564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94395 bytes_read=2499059 bytes_retransmit=0 bytes_invalid=0 send_seq=11123 receive_seq=11123 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998674 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.5 th2: temp=61.1 th3: temp=58.6 sysload=0.29 cputime=480.059 memavail=7393980 print_time=6409.174 buffer_time=2.258 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 51 Hz
Stats 6385.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29483381 bytes_read=4610300 bytes_retransmit=9 bytes_invalid=0 send_seq=557422 receive_seq=557422 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=11264 freq=400015867 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=39556 bytes_read=123808 bytes_retransmit=0 bytes_invalid=0 send_seq=6564 receive_seq=6564 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999594 adj=49997642 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192688 bytes_read=6136715 bytes_retransmit=9 bytes_invalid=0 send_seq=26818 receive_seq=26818 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997741 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129116 bytes_read=3447711 bytes_retransmit=9 bytes_invalid=0 send_seq=17828 receive_seq=17828 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997521 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39823 bytes_read=1630163 bytes_retransmit=9 bytes_invalid=0 send_seq=6578 receive_seq=6578 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40309 bytes_read=121388 bytes_retransmit=9 bytes_invalid=0 send_seq=6565 receive_seq=6565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94401 bytes_read=2499415 bytes_retransmit=0 bytes_invalid=0 send_seq=11124 receive_seq=11124 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998685 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=55.5 th1: temp=55.5 th2: temp=60.9 th3: temp=58.6 sysload=0.27 cputime=480.171 memavail=7393980 print_time=6410.076 buffer_time=2.160 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 52 Hz
Stats 6386.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29493891 bytes_read=4611564 bytes_retransmit=9 bytes_invalid=0 send_seq=557607 receive_seq=557607 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=9041 freq=400015883 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39562 bytes_read=123837 bytes_retransmit=0 bytes_invalid=0 send_seq=6565 receive_seq=6565 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999595 adj=49997679 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192694 bytes_read=6136843 bytes_retransmit=9 bytes_invalid=0 send_seq=26819 receive_seq=26819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997746 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129192 bytes_read=3450782 bytes_retransmit=9 bytes_invalid=0 send_seq=17839 receive_seq=17839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39829 bytes_read=1630397 bytes_retransmit=9 bytes_invalid=0 send_seq=6579 receive_seq=6579 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997709 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40315 bytes_read=121404 bytes_retransmit=9 bytes_invalid=0 send_seq=6566 receive_seq=6566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94407 bytes_read=2499771 bytes_retransmit=0 bytes_invalid=0 send_seq=11125 receive_seq=11125 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998691 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.6 th2: temp=60.7 th3: temp=58.5 sysload=0.27 cputime=480.289 memavail=7393980 print_time=6410.982 buffer_time=2.065 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 53 Hz
Stats 6387.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29504167 bytes_read=4612805 bytes_retransmit=9 bytes_invalid=0 send_seq=557790 receive_seq=557790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=10735 freq=400015883 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39568 bytes_read=123853 bytes_retransmit=0 bytes_invalid=0 send_seq=6566 receive_seq=6566 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999594 adj=49997651 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192700 bytes_read=6136943 bytes_retransmit=9 bytes_invalid=0 send_seq=26820 receive_seq=26820 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997686 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129268 bytes_read=3453853 bytes_retransmit=9 bytes_invalid=0 send_seq=17850 receive_seq=17850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000043 adj=63997508 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39835 bytes_read=1630691 bytes_retransmit=9 bytes_invalid=0 send_seq=6580 receive_seq=6580 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997677 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40321 bytes_read=121431 bytes_retransmit=9 bytes_invalid=0 send_seq=6567 receive_seq=6567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94413 bytes_read=2500127 bytes_retransmit=0 bytes_invalid=0 send_seq=11126 receive_seq=11126 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998703 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=56.6 th1: temp=55.3 th2: temp=60.8 th3: temp=58.5 sysload=0.27 cputime=480.422 memavail=7393752 print_time=6412.185 buffer_time=2.268 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 54 Hz
Stats 6388.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29513153 bytes_read=4613921 bytes_retransmit=9 bytes_invalid=0 send_seq=557952 receive_seq=557952 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=12125 freq=400015882 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39574 bytes_read=123869 bytes_retransmit=0 bytes_invalid=0 send_seq=6567 receive_seq=6567 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999592 adj=49997629 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192706 bytes_read=6137043 bytes_retransmit=9 bytes_invalid=0 send_seq=26821 receive_seq=26821 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997670 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129344 bytes_read=3456931 bytes_retransmit=9 bytes_invalid=0 send_seq=17861 receive_seq=17861 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000042 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39841 bytes_read=1630925 bytes_retransmit=9 bytes_invalid=0 send_seq=6581 receive_seq=6581 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40327 bytes_read=121447 bytes_retransmit=9 bytes_invalid=0 send_seq=6568 receive_seq=6568 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94419 bytes_read=2500483 bytes_retransmit=0 bytes_invalid=0 send_seq=11127 receive_seq=11127 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998685 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.5 th2: temp=60.9 th3: temp=58.7 sysload=0.27 cputime=480.538 memavail=7393752 print_time=6413.097 buffer_time=2.180 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 55 Hz
Stats 6389.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29524075 bytes_read=4615235 bytes_retransmit=9 bytes_invalid=0 send_seq=558147 receive_seq=558147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=9549 freq=400015890 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39580 bytes_read=123885 bytes_retransmit=0 bytes_invalid=0 send_seq=6568 receive_seq=6568 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999593 adj=49997604 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192712 bytes_read=6137171 bytes_retransmit=9 bytes_invalid=0 send_seq=26822 receive_seq=26822 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997668 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129420 bytes_read=3460060 bytes_retransmit=9 bytes_invalid=0 send_seq=17872 receive_seq=17872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997487 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39847 bytes_read=1631174 bytes_retransmit=9 bytes_invalid=0 send_seq=6582 receive_seq=6582 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40333 bytes_read=121463 bytes_retransmit=9 bytes_invalid=0 send_seq=6569 receive_seq=6569 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94425 bytes_read=2500839 bytes_retransmit=0 bytes_invalid=0 send_seq=11128 receive_seq=11128 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998683 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.4 th2: temp=60.9 th3: temp=58.5 sysload=0.27 cputime=480.658 memavail=7393752 print_time=6413.998 buffer_time=2.081 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 56 Hz
Stats 6390.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29534733 bytes_read=4616485 bytes_retransmit=9 bytes_invalid=0 send_seq=558335 receive_seq=558335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=11304 freq=400015876 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39586 bytes_read=123901 bytes_retransmit=0 bytes_invalid=0 send_seq=6569 receive_seq=6569 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999593 adj=49997605 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192718 bytes_read=6137285 bytes_retransmit=9 bytes_invalid=0 send_seq=26823 receive_seq=26823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997749 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129496 bytes_read=3463132 bytes_retransmit=9 bytes_invalid=0 send_seq=17883 receive_seq=17883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997462 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39853 bytes_read=1631468 bytes_retransmit=9 bytes_invalid=0 send_seq=6583 receive_seq=6583 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40339 bytes_read=121479 bytes_retransmit=9 bytes_invalid=0 send_seq=6570 receive_seq=6570 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94431 bytes_read=2501195 bytes_retransmit=0 bytes_invalid=0 send_seq=11129 receive_seq=11129 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998666 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.6 th1: temp=55.4 th2: temp=61.0 th3: temp=58.6 sysload=0.49 cputime=480.791 memavail=7393800 print_time=6415.211 buffer_time=2.293 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 57 Hz
Stats 6391.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29543785 bytes_read=4617590 bytes_retransmit=9 bytes_invalid=0 send_seq=558495 receive_seq=558494 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=12821 freq=400015882 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39592 bytes_read=123930 bytes_retransmit=0 bytes_invalid=0 send_seq=6570 receive_seq=6570 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999592 adj=49997621 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192724 bytes_read=6137385 bytes_retransmit=9 bytes_invalid=0 send_seq=26824 receive_seq=26824 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997734 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129572 bytes_read=3466188 bytes_retransmit=9 bytes_invalid=0 send_seq=17894 receive_seq=17894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997488 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39859 bytes_read=1631702 bytes_retransmit=9 bytes_invalid=0 send_seq=6584 receive_seq=6584 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40345 bytes_read=121495 bytes_retransmit=9 bytes_invalid=0 send_seq=6571 receive_seq=6571 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94437 bytes_read=2501551 bytes_retransmit=0 bytes_invalid=0 send_seq=11130 receive_seq=11130 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998674 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.4 th2: temp=60.8 th3: temp=58.5 sysload=0.49 cputime=480.909 memavail=7393800 print_time=6416.107 buffer_time=2.188 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 58 Hz
Stats 6392.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29554928 bytes_read=4618925 bytes_retransmit=9 bytes_invalid=0 send_seq=558690 receive_seq=558690 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=10551 freq=400015887 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39598 bytes_read=123946 bytes_retransmit=0 bytes_invalid=0 send_seq=6571 receive_seq=6571 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999591 adj=49997601 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192730 bytes_read=6137513 bytes_retransmit=9 bytes_invalid=0 send_seq=26825 receive_seq=26825 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997698 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129648 bytes_read=3469258 bytes_retransmit=9 bytes_invalid=0 send_seq=17905 receive_seq=17905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000040 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39865 bytes_read=1631936 bytes_retransmit=9 bytes_invalid=0 send_seq=6585 receive_seq=6585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40351 bytes_read=121522 bytes_retransmit=9 bytes_invalid=0 send_seq=6572 receive_seq=6572 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94443 bytes_read=2501907 bytes_retransmit=0 bytes_invalid=0 send_seq=11131 receive_seq=11131 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998661 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.5 th2: temp=60.9 th3: temp=58.5 sysload=0.49 cputime=481.041 memavail=7388092 print_time=6417.026 buffer_time=2.106 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 59 Hz
Stats 6393.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29566089 bytes_read=4620220 bytes_retransmit=9 bytes_invalid=0 send_seq=558887 receive_seq=558887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=12099 freq=400015950 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39604 bytes_read=123962 bytes_retransmit=0 bytes_invalid=0 send_seq=6572 receive_seq=6572 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999595 adj=49997583 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192736 bytes_read=6137613 bytes_retransmit=9 bytes_invalid=0 send_seq=26826 receive_seq=26826 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997675 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129724 bytes_read=3472348 bytes_retransmit=9 bytes_invalid=0 send_seq=17916 receive_seq=17916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997468 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39871 bytes_read=1632230 bytes_retransmit=9 bytes_invalid=0 send_seq=6586 receive_seq=6586 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40357 bytes_read=121538 bytes_retransmit=9 bytes_invalid=0 send_seq=6573 receive_seq=6573 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94449 bytes_read=2502263 bytes_retransmit=0 bytes_invalid=0 send_seq=11132 receive_seq=11132 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998651 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.6 th2: temp=60.8 th3: temp=58.5 sysload=0.49 cputime=481.176 memavail=7394228 print_time=6418.230 buffer_time=2.307 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 60 Hz
Stats 6394.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29575475 bytes_read=4621360 bytes_retransmit=9 bytes_invalid=0 send_seq=559053 receive_seq=559053 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=13497 freq=400015979 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39610 bytes_read=123978 bytes_retransmit=0 bytes_invalid=0 send_seq=6573 receive_seq=6573 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999593 adj=49997540 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192742 bytes_read=6137713 bytes_retransmit=9 bytes_invalid=0 send_seq=26827 receive_seq=26827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997543 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129800 bytes_read=3475404 bytes_retransmit=9 bytes_invalid=0 send_seq=17927 receive_seq=17927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997369 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39877 bytes_read=1632479 bytes_retransmit=9 bytes_invalid=0 send_seq=6587 receive_seq=6587 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997586 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40363 bytes_read=121554 bytes_retransmit=9 bytes_invalid=0 send_seq=6574 receive_seq=6574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999419 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94455 bytes_read=2502619 bytes_retransmit=0 bytes_invalid=0 send_seq=11133 receive_seq=11133 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998595 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.6 th2: temp=60.9 th3: temp=58.5 sysload=0.49 cputime=481.291 memavail=7394228 print_time=6419.128 buffer_time=2.204 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 61 Hz
Stats 6395.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29586853 bytes_read=4622699 bytes_retransmit=9 bytes_invalid=0 send_seq=559253 receive_seq=559253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=11093 freq=400015991 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39616 bytes_read=123994 bytes_retransmit=0 bytes_invalid=0 send_seq=6574 receive_seq=6574 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999592 adj=49997483 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192748 bytes_read=6137855 bytes_retransmit=9 bytes_invalid=0 send_seq=26828 receive_seq=26828 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997492 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129876 bytes_read=3478474 bytes_retransmit=9 bytes_invalid=0 send_seq=17938 receive_seq=17938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997390 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39883 bytes_read=1632713 bytes_retransmit=9 bytes_invalid=0 send_seq=6588 receive_seq=6588 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997550 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40369 bytes_read=121570 bytes_retransmit=9 bytes_invalid=0 send_seq=6575 receive_seq=6575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94461 bytes_read=2502975 bytes_retransmit=0 bytes_invalid=0 send_seq=11134 receive_seq=11134 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998572 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.5 th2: temp=61.0 th3: temp=58.7 sysload=0.45 cputime=481.413 memavail=7394228 print_time=6420.038 buffer_time=2.114 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 62 Hz
Stats 6396.3: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29598321 bytes_read=4624040 bytes_retransmit=9 bytes_invalid=0 send_seq=559457 receive_seq=559457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=10615 freq=400015973 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39628 bytes_read=124039 bytes_retransmit=0 bytes_invalid=0 send_seq=6576 receive_seq=6576 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999592 adj=49997467 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192760 bytes_read=6137971 bytes_retransmit=9 bytes_invalid=0 send_seq=26830 receive_seq=26830 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997473 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=129958 bytes_read=3481619 bytes_retransmit=9 bytes_invalid=0 send_seq=17950 receive_seq=17950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997381 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39895 bytes_read=1633023 bytes_retransmit=9 bytes_invalid=0 send_seq=6590 receive_seq=6590 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997539 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40381 bytes_read=121602 bytes_retransmit=9 bytes_invalid=0 send_seq=6577 receive_seq=6577 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999423 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94473 bytes_read=2503347 bytes_retransmit=0 bytes_invalid=0 send_seq=11136 receive_seq=11136 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998579 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.8 th2: temp=61.0 th3: temp=58.5 sysload=0.45 cputime=481.535 memavail=7393976 print_time=6420.927 buffer_time=2.002 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 63 Hz
Stats 6397.3: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29607840 bytes_read=4625216 bytes_retransmit=9 bytes_invalid=0 send_seq=559627 receive_seq=559627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=14106 freq=400015964 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39634 bytes_read=124055 bytes_retransmit=0 bytes_invalid=0 send_seq=6577 receive_seq=6577 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999591 adj=49997514 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192766 bytes_read=6138071 bytes_retransmit=9 bytes_invalid=0 send_seq=26831 receive_seq=26831 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997589 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130034 bytes_read=3484677 bytes_retransmit=9 bytes_invalid=0 send_seq=17961 receive_seq=17961 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39901 bytes_read=1633257 bytes_retransmit=9 bytes_invalid=0 send_seq=6591 receive_seq=6591 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997604 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40387 bytes_read=121629 bytes_retransmit=9 bytes_invalid=0 send_seq=6578 receive_seq=6578 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94479 bytes_read=2503703 bytes_retransmit=0 bytes_invalid=0 send_seq=11137 receive_seq=11137 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998623 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.5 th2: temp=60.8 th3: temp=58.5 sysload=0.45 cputime=481.667 memavail=7393728 print_time=6422.124 buffer_time=2.198 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 64 Hz
Stats 6398.3: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29619630 bytes_read=4626590 bytes_retransmit=9 bytes_invalid=0 send_seq=559835 receive_seq=559835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=11996 freq=400015960 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39640 bytes_read=124071 bytes_retransmit=0 bytes_invalid=0 send_seq=6578 receive_seq=6578 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999591 adj=49997541 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192772 bytes_read=6138199 bytes_retransmit=9 bytes_invalid=0 send_seq=26832 receive_seq=26832 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997610 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130110 bytes_read=3487764 bytes_retransmit=9 bytes_invalid=0 send_seq=17972 receive_seq=17972 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39907 bytes_read=1633491 bytes_retransmit=9 bytes_invalid=0 send_seq=6592 receive_seq=6592 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997626 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40393 bytes_read=121645 bytes_retransmit=9 bytes_invalid=0 send_seq=6579 receive_seq=6579 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94485 bytes_read=2504059 bytes_retransmit=0 bytes_invalid=0 send_seq=11138 receive_seq=11138 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998644 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.6 th2: temp=60.9 th3: temp=58.6 sysload=0.45 cputime=481.793 memavail=7393728 print_time=6423.061 buffer_time=2.135 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 65 Hz
Stats 6399.3: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29631408 bytes_read=4627933 bytes_retransmit=9 bytes_invalid=0 send_seq=560042 receive_seq=560042 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=11115 freq=400015949 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39646 bytes_read=124087 bytes_retransmit=0 bytes_invalid=0 send_seq=6579 receive_seq=6579 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999589 adj=49997546 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192778 bytes_read=6138299 bytes_retransmit=9 bytes_invalid=0 send_seq=26833 receive_seq=26833 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997607 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130186 bytes_read=3490836 bytes_retransmit=9 bytes_invalid=0 send_seq=17983 receive_seq=17983 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997666 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39913 bytes_read=1633800 bytes_retransmit=9 bytes_invalid=0 send_seq=6593 receive_seq=6593 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997626 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40399 bytes_read=121661 bytes_retransmit=9 bytes_invalid=0 send_seq=6580 receive_seq=6580 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94491 bytes_read=2504415 bytes_retransmit=0 bytes_invalid=0 send_seq=11139 receive_seq=11139 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998644 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.4 th2: temp=60.9 th3: temp=58.3 sysload=0.45 cputime=481.915 memavail=7393728 print_time=6423.929 buffer_time=2.002 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 66 Hz
Stats 6400.3: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29641177 bytes_read=4629108 bytes_retransmit=9 bytes_invalid=0 send_seq=560215 receive_seq=560215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=14829 freq=400015951 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39652 bytes_read=124103 bytes_retransmit=0 bytes_invalid=0 send_seq=6580 receive_seq=6580 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999587 adj=49997555 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192784 bytes_read=6138413 bytes_retransmit=9 bytes_invalid=0 send_seq=26834 receive_seq=26834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997621 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130262 bytes_read=3493895 bytes_retransmit=9 bytes_invalid=0 send_seq=17994 receive_seq=17994 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997650 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39919 bytes_read=1634034 bytes_retransmit=9 bytes_invalid=0 send_seq=6594 receive_seq=6594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997649 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40405 bytes_read=121677 bytes_retransmit=9 bytes_invalid=0 send_seq=6581 receive_seq=6581 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94497 bytes_read=2504760 bytes_retransmit=0 bytes_invalid=0 send_seq=11140 receive_seq=11140 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998651 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.4 th2: temp=60.9 th3: temp=58.4 sysload=0.49 cputime=482.049 memavail=7393728 print_time=6425.142 buffer_time=2.215 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 67 Hz
Stats 6401.3: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29653282 bytes_read=4630512 bytes_retransmit=9 bytes_invalid=0 send_seq=560428 receive_seq=560428 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=43 upcoming_bytes=12693 freq=400015951 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39658 bytes_read=124132 bytes_retransmit=0 bytes_invalid=0 send_seq=6581 receive_seq=6581 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999587 adj=49997542 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192790 bytes_read=6138541 bytes_retransmit=9 bytes_invalid=0 send_seq=26835 receive_seq=26835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997617 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130331 bytes_read=3496942 bytes_retransmit=9 bytes_invalid=0 send_seq=18004 receive_seq=18004 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997580 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39925 bytes_read=1634268 bytes_retransmit=9 bytes_invalid=0 send_seq=6595 receive_seq=6595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40411 bytes_read=121693 bytes_retransmit=9 bytes_invalid=0 send_seq=6582 receive_seq=6582 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94503 bytes_read=2505105 bytes_retransmit=0 bytes_invalid=0 send_seq=11141 receive_seq=11141 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998652 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.4 th2: temp=60.8 th3: temp=58.5 sysload=0.49 cputime=482.175 memavail=7393748 print_time=6426.072 buffer_time=2.144 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 68 Hz
Stats 6402.3: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29665410 bytes_read=4631883 bytes_retransmit=9 bytes_invalid=0 send_seq=560637 receive_seq=560637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=11732 freq=400015969 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39664 bytes_read=124148 bytes_retransmit=0 bytes_invalid=0 send_seq=6582 receive_seq=6582 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999587 adj=49997538 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192796 bytes_read=6138641 bytes_retransmit=9 bytes_invalid=0 send_seq=26836 receive_seq=26836 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997608 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130407 bytes_read=3500014 bytes_retransmit=9 bytes_invalid=0 send_seq=18015 receive_seq=18015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997556 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39931 bytes_read=1634562 bytes_retransmit=9 bytes_invalid=0 send_seq=6596 receive_seq=6596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997634 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40417 bytes_read=121720 bytes_retransmit=9 bytes_invalid=0 send_seq=6583 receive_seq=6583 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94509 bytes_read=2505449 bytes_retransmit=0 bytes_invalid=0 send_seq=11142 receive_seq=11142 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998653 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.3 th2: temp=61.0 th3: temp=58.5 sysload=0.49 cputime=482.297 memavail=7393748 print_time=6426.940 buffer_time=2.012 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 69 Hz
Stats 6403.3: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29675480 bytes_read=4633083 bytes_retransmit=9 bytes_invalid=0 send_seq=560815 receive_seq=560815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=15541 freq=400016059 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39670 bytes_read=124164 bytes_retransmit=0 bytes_invalid=0 send_seq=6583 receive_seq=6583 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999587 adj=49997527 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192802 bytes_read=6138741 bytes_retransmit=9 bytes_invalid=0 send_seq=26837 receive_seq=26837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997580 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130483 bytes_read=3503146 bytes_retransmit=9 bytes_invalid=0 send_seq=18026 receive_seq=18026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997561 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39937 bytes_read=1634796 bytes_retransmit=9 bytes_invalid=0 send_seq=6597 receive_seq=6597 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997616 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40423 bytes_read=121736 bytes_retransmit=9 bytes_invalid=0 send_seq=6584 receive_seq=6584 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94515 bytes_read=2505794 bytes_retransmit=0 bytes_invalid=0 send_seq=11143 receive_seq=11143 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998668 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.5 th2: temp=61.2 th3: temp=58.5 sysload=0.49 cputime=482.431 memavail=7393748 print_time=6428.152 buffer_time=2.222 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 70 Hz
Stats 6404.3: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29687858 bytes_read=4634502 bytes_retransmit=9 bytes_invalid=0 send_seq=561031 receive_seq=561031 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=13444 freq=400016049 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39676 bytes_read=124180 bytes_retransmit=0 bytes_invalid=0 send_seq=6584 receive_seq=6584 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999586 adj=49997405 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192808 bytes_read=6138869 bytes_retransmit=9 bytes_invalid=0 send_seq=26838 receive_seq=26838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997424 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130559 bytes_read=3506218 bytes_retransmit=9 bytes_invalid=0 send_seq=18037 receive_seq=18037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997347 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39943 bytes_read=1635045 bytes_retransmit=9 bytes_invalid=0 send_seq=6598 receive_seq=6598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997495 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40429 bytes_read=121752 bytes_retransmit=9 bytes_invalid=0 send_seq=6585 receive_seq=6585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999413 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94521 bytes_read=2506139 bytes_retransmit=0 bytes_invalid=0 send_seq=11144 receive_seq=11144 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998607 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.5 th2: temp=61.0 th3: temp=58.5 sysload=0.49 cputime=482.560 memavail=7393496 print_time=6429.070 buffer_time=2.140 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 71 Hz
Stats 6405.3: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29700492 bytes_read=4635917 bytes_retransmit=9 bytes_invalid=0 send_seq=561252 receive_seq=561252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=12371 freq=400016045 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39682 bytes_read=124196 bytes_retransmit=0 bytes_invalid=0 send_seq=6585 receive_seq=6585 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999585 adj=49997430 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192814 bytes_read=6138983 bytes_retransmit=9 bytes_invalid=0 send_seq=26839 receive_seq=26839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997475 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130635 bytes_read=3509291 bytes_retransmit=9 bytes_invalid=0 send_seq=18048 receive_seq=18048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997462 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39949 bytes_read=1635339 bytes_retransmit=9 bytes_invalid=0 send_seq=6599 receive_seq=6599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997529 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40435 bytes_read=121768 bytes_retransmit=9 bytes_invalid=0 send_seq=6586 receive_seq=6586 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999416 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94527 bytes_read=2506484 bytes_retransmit=0 bytes_invalid=0 send_seq=11145 receive_seq=11145 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998619 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.5 th2: temp=61.0 th3: temp=58.4 sysload=0.45 cputime=482.700 memavail=7393672 print_time=6429.955 buffer_time=2.024 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 72 Hz
Stats 6406.3: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29710950 bytes_read=4637157 bytes_retransmit=9 bytes_invalid=0 send_seq=561438 receive_seq=561438 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=16115 freq=400016054 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39688 bytes_read=124225 bytes_retransmit=0 bytes_invalid=0 send_seq=6586 receive_seq=6586 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999584 adj=49997449 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192820 bytes_read=6139083 bytes_retransmit=9 bytes_invalid=0 send_seq=26840 receive_seq=26840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997491 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130711 bytes_read=3512349 bytes_retransmit=9 bytes_invalid=0 send_seq=18059 receive_seq=18059 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997453 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39955 bytes_read=1635573 bytes_retransmit=9 bytes_invalid=0 send_seq=6600 receive_seq=6600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997540 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40441 bytes_read=121784 bytes_retransmit=9 bytes_invalid=0 send_seq=6587 receive_seq=6587 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999419 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94533 bytes_read=2506829 bytes_retransmit=0 bytes_invalid=0 send_seq=11146 receive_seq=11146 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998618 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.7 th2: temp=61.0 th3: temp=58.4 sysload=0.45 cputime=482.836 memavail=7393772 print_time=6431.168 buffer_time=2.236 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 73 Hz
Stats 6407.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29723576 bytes_read=4638602 bytes_retransmit=9 bytes_invalid=0 send_seq=561656 receive_seq=561656 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=14724 freq=400016048 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39694 bytes_read=124241 bytes_retransmit=0 bytes_invalid=0 send_seq=6587 receive_seq=6587 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999584 adj=49997461 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192826 bytes_read=6139211 bytes_retransmit=9 bytes_invalid=0 send_seq=26841 receive_seq=26841 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997584 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130787 bytes_read=3515420 bytes_retransmit=9 bytes_invalid=0 send_seq=18070 receive_seq=18070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997432 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39961 bytes_read=1635807 bytes_retransmit=9 bytes_invalid=0 send_seq=6601 receive_seq=6601 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997547 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40447 bytes_read=121811 bytes_retransmit=9 bytes_invalid=0 send_seq=6588 receive_seq=6588 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999419 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94539 bytes_read=2507174 bytes_retransmit=0 bytes_invalid=0 send_seq=11147 receive_seq=11147 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998637 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.6 th2: temp=61.0 th3: temp=58.6 sysload=0.45 cputime=482.961 memavail=7393276 print_time=6432.102 buffer_time=2.170 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 74 Hz
Stats 6408.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29736407 bytes_read=4640022 bytes_retransmit=9 bytes_invalid=0 send_seq=561878 receive_seq=561878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=13107 freq=400016074 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39700 bytes_read=124257 bytes_retransmit=0 bytes_invalid=0 send_seq=6588 receive_seq=6588 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999583 adj=49997489 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192832 bytes_read=6139311 bytes_retransmit=9 bytes_invalid=0 send_seq=26842 receive_seq=26842 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997592 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130863 bytes_read=3518508 bytes_retransmit=9 bytes_invalid=0 send_seq=18081 receive_seq=18081 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997445 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=39967 bytes_read=1636101 bytes_retransmit=9 bytes_invalid=0 send_seq=6602 receive_seq=6602 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997561 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40453 bytes_read=121827 bytes_retransmit=9 bytes_invalid=0 send_seq=6589 receive_seq=6589 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999421 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94545 bytes_read=2507527 bytes_retransmit=0 bytes_invalid=0 send_seq=11148 receive_seq=11148 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998638 coil_temp=16.9 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.7 th2: temp=60.9 th3: temp=58.5 sysload=0.45 cputime=483.087 memavail=7393276 print_time=6432.975 buffer_time=2.042 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 75 Hz
Stats 6409.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29747044 bytes_read=4641256 bytes_retransmit=9 bytes_invalid=0 send_seq=562064 receive_seq=562064 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=16949 freq=400016055 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39706 bytes_read=124273 bytes_retransmit=0 bytes_invalid=0 send_seq=6589 receive_seq=6589 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999582 adj=49997447 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192838 bytes_read=6139411 bytes_retransmit=9 bytes_invalid=0 send_seq=26843 receive_seq=26843 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997627 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=130939 bytes_read=3521565 bytes_retransmit=9 bytes_invalid=0 send_seq=18092 receive_seq=18092 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997372 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39973 bytes_read=1636350 bytes_retransmit=9 bytes_invalid=0 send_seq=6603 receive_seq=6603 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997522 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40459 bytes_read=121843 bytes_retransmit=9 bytes_invalid=0 send_seq=6590 receive_seq=6590 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999414 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94551 bytes_read=2507883 bytes_retransmit=0 bytes_invalid=0 send_seq=11149 receive_seq=11149 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998603 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.5 th2: temp=61.0 th3: temp=58.6 sysload=0.45 cputime=483.229 memavail=7389756 print_time=6434.172 buffer_time=2.239 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 76 Hz
Stats 6410.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29760114 bytes_read=4642720 bytes_retransmit=9 bytes_invalid=0 send_seq=562289 receive_seq=562289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=15532 freq=400016046 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39712 bytes_read=124289 bytes_retransmit=0 bytes_invalid=0 send_seq=6590 receive_seq=6590 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999581 adj=49997503 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192844 bytes_read=6139553 bytes_retransmit=9 bytes_invalid=0 send_seq=26844 receive_seq=26844 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997654 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131015 bytes_read=3524713 bytes_retransmit=9 bytes_invalid=0 send_seq=18103 receive_seq=18103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997436 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39979 bytes_read=1636584 bytes_retransmit=9 bytes_invalid=0 send_seq=6604 receive_seq=6604 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997579 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40465 bytes_read=121859 bytes_retransmit=9 bytes_invalid=0 send_seq=6591 receive_seq=6591 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94557 bytes_read=2508223 bytes_retransmit=0 bytes_invalid=0 send_seq=11150 receive_seq=11150 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998634 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=56.1 th1: temp=55.8 th2: temp=60.8 th3: temp=58.5 sysload=0.42 cputime=483.364 memavail=7395388 print_time=6435.106 buffer_time=2.173 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 77 Hz
Stats 6411.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29773246 bytes_read=4644175 bytes_retransmit=9 bytes_invalid=0 send_seq=562518 receive_seq=562518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=13753 freq=400016040 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39718 bytes_read=124318 bytes_retransmit=0 bytes_invalid=0 send_seq=6591 receive_seq=6591 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999580 adj=49997516 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192850 bytes_read=6139653 bytes_retransmit=9 bytes_invalid=0 send_seq=26845 receive_seq=26845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997654 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131091 bytes_read=3527772 bytes_retransmit=9 bytes_invalid=0 send_seq=18114 receive_seq=18114 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997440 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39985 bytes_read=1636878 bytes_retransmit=9 bytes_invalid=0 send_seq=6605 receive_seq=6605 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997592 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40471 bytes_read=121875 bytes_retransmit=9 bytes_invalid=0 send_seq=6592 receive_seq=6592 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94563 bytes_read=2508579 bytes_retransmit=0 bytes_invalid=0 send_seq=11151 receive_seq=11151 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998657 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.6 th2: temp=61.2 th3: temp=58.4 sysload=0.42 cputime=483.491 memavail=7395388 print_time=6435.984 buffer_time=2.050 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 78 Hz
Stats 6412.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29784199 bytes_read=4645471 bytes_retransmit=9 bytes_invalid=0 send_seq=562712 receive_seq=562712 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=43 upcoming_bytes=17637 freq=400016021 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39724 bytes_read=124334 bytes_retransmit=0 bytes_invalid=0 send_seq=6592 receive_seq=6592 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999578 adj=49997517 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192856 bytes_read=6139753 bytes_retransmit=9 bytes_invalid=0 send_seq=26846 receive_seq=26846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997646 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131167 bytes_read=3530828 bytes_retransmit=9 bytes_invalid=0 send_seq=18125 receive_seq=18125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997443 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39991 bytes_read=1637112 bytes_retransmit=9 bytes_invalid=0 send_seq=6606 receive_seq=6606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40477 bytes_read=121902 bytes_retransmit=9 bytes_invalid=0 send_seq=6593 receive_seq=6593 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94569 bytes_read=2508935 bytes_retransmit=0 bytes_invalid=0 send_seq=11152 receive_seq=11152 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998688 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=56.1 th1: temp=55.6 th2: temp=61.0 th3: temp=58.7 sysload=0.42 cputime=483.632 memavail=7395396 print_time=6437.186 buffer_time=2.252 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 79 Hz
Stats 6413.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29797714 bytes_read=4646990 bytes_retransmit=9 bytes_invalid=0 send_seq=562948 receive_seq=562948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=16080 freq=400016023 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39730 bytes_read=124350 bytes_retransmit=0 bytes_invalid=0 send_seq=6593 receive_seq=6593 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999578 adj=49997539 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192862 bytes_read=6139881 bytes_retransmit=9 bytes_invalid=0 send_seq=26847 receive_seq=26847 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997681 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131243 bytes_read=3533929 bytes_retransmit=9 bytes_invalid=0 send_seq=18136 receive_seq=18136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997472 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=39997 bytes_read=1637346 bytes_retransmit=9 bytes_invalid=0 send_seq=6607 receive_seq=6607 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40483 bytes_read=121918 bytes_retransmit=9 bytes_invalid=0 send_seq=6594 receive_seq=6594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94575 bytes_read=2509291 bytes_retransmit=0 bytes_invalid=0 send_seq=11153 receive_seq=11153 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998692 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.6 th2: temp=60.9 th3: temp=58.4 sysload=0.42 cputime=483.763 memavail=7395396 print_time=6438.119 buffer_time=2.184 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 80 Hz
Stats 6414.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29811188 bytes_read=4648470 bytes_retransmit=9 bytes_invalid=0 send_seq=563182 receive_seq=563182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=13852 freq=400016017 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39736 bytes_read=124366 bytes_retransmit=0 bytes_invalid=0 send_seq=6594 receive_seq=6594 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999577 adj=49997534 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192868 bytes_read=6139981 bytes_retransmit=9 bytes_invalid=0 send_seq=26848 receive_seq=26848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997655 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131319 bytes_read=3536985 bytes_retransmit=9 bytes_invalid=0 send_seq=18147 receive_seq=18147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997458 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40003 bytes_read=1637655 bytes_retransmit=9 bytes_invalid=0 send_seq=6608 receive_seq=6608 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40489 bytes_read=121934 bytes_retransmit=9 bytes_invalid=0 send_seq=6595 receive_seq=6595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94581 bytes_read=2509647 bytes_retransmit=0 bytes_invalid=0 send_seq=11154 receive_seq=11154 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998686 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.7 th2: temp=60.9 th3: temp=58.5 sysload=0.42 cputime=483.892 memavail=7395396 print_time=6438.989 buffer_time=2.053 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 81 Hz
Stats 6415.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29822215 bytes_read=4649745 bytes_retransmit=9 bytes_invalid=0 send_seq=563375 receive_seq=563375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=18103 freq=400016082 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39742 bytes_read=124382 bytes_retransmit=0 bytes_invalid=0 send_seq=6595 receive_seq=6595 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999577 adj=49997543 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192874 bytes_read=6140095 bytes_retransmit=9 bytes_invalid=0 send_seq=26849 receive_seq=26849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997651 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131388 bytes_read=3540021 bytes_retransmit=9 bytes_invalid=0 send_seq=18157 receive_seq=18157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997455 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40009 bytes_read=1637889 bytes_retransmit=9 bytes_invalid=0 send_seq=6609 receive_seq=6609 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40495 bytes_read=121950 bytes_retransmit=9 bytes_invalid=0 send_seq=6596 receive_seq=6596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94587 bytes_read=2510003 bytes_retransmit=0 bytes_invalid=0 send_seq=11155 receive_seq=11155 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998691 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.5 th2: temp=60.8 th3: temp=58.5 sysload=0.38 cputime=484.032 memavail=7395396 print_time=6440.196 buffer_time=2.258 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 82 Hz
Stats 6416.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29835684 bytes_read=4651254 bytes_retransmit=9 bytes_invalid=0 send_seq=563609 receive_seq=563609 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=17112 freq=400016149 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39748 bytes_read=124411 bytes_retransmit=0 bytes_invalid=0 send_seq=6596 receive_seq=6596 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999576 adj=49997453 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192880 bytes_read=6140223 bytes_retransmit=9 bytes_invalid=0 send_seq=26850 receive_seq=26850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997519 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131464 bytes_read=3543105 bytes_retransmit=9 bytes_invalid=0 send_seq=18168 receive_seq=18168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997351 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40015 bytes_read=1638123 bytes_retransmit=9 bytes_invalid=0 send_seq=6610 receive_seq=6610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997552 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40501 bytes_read=121966 bytes_retransmit=9 bytes_invalid=0 send_seq=6597 receive_seq=6597 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999417 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94593 bytes_read=2510359 bytes_retransmit=0 bytes_invalid=0 send_seq=11156 receive_seq=11156 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998623 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=56.5 th1: temp=55.7 th2: temp=60.9 th3: temp=58.4 sysload=0.38 cputime=484.164 memavail=7395396 print_time=6441.131 buffer_time=2.192 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 83 Hz
Stats 6417.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29849652 bytes_read=4652785 bytes_retransmit=9 bytes_invalid=0 send_seq=563850 receive_seq=563850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=14269 freq=400016130 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39754 bytes_read=124427 bytes_retransmit=0 bytes_invalid=0 send_seq=6597 receive_seq=6597 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999575 adj=49997355 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192886 bytes_read=6140323 bytes_retransmit=9 bytes_invalid=0 send_seq=26851 receive_seq=26851 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997391 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131540 bytes_read=3546220 bytes_retransmit=9 bytes_invalid=0 send_seq=18179 receive_seq=18179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997227 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40021 bytes_read=1638417 bytes_retransmit=9 bytes_invalid=0 send_seq=6611 receive_seq=6611 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997476 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40507 bytes_read=121993 bytes_retransmit=9 bytes_invalid=0 send_seq=6598 receive_seq=6598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999394 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94599 bytes_read=2510715 bytes_retransmit=0 bytes_invalid=0 send_seq=11157 receive_seq=11157 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998553 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=56.1 th1: temp=55.8 th2: temp=61.1 th3: temp=58.5 sysload=0.38 cputime=484.296 memavail=7394180 print_time=6441.999 buffer_time=2.059 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 84 Hz
Stats 6418.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29860916 bytes_read=4654095 bytes_retransmit=9 bytes_invalid=0 send_seq=564050 receive_seq=564050 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=18346 freq=400016142 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39760 bytes_read=124443 bytes_retransmit=0 bytes_invalid=0 send_seq=6598 receive_seq=6598 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999574 adj=49997396 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192892 bytes_read=6140423 bytes_retransmit=9 bytes_invalid=0 send_seq=26852 receive_seq=26852 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997441 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131616 bytes_read=3549295 bytes_retransmit=9 bytes_invalid=0 send_seq=18190 receive_seq=18190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997274 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40027 bytes_read=1638647 bytes_retransmit=9 bytes_invalid=0 send_seq=6612 receive_seq=6612 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997543 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40513 bytes_read=122009 bytes_retransmit=9 bytes_invalid=0 send_seq=6599 receive_seq=6599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999403 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94605 bytes_read=2511071 bytes_retransmit=0 bytes_invalid=0 send_seq=11158 receive_seq=11158 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998569 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.6 th2: temp=61.0 th3: temp=58.4 sysload=0.38 cputime=484.438 memavail=7394180 print_time=6443.211 buffer_time=2.265 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 85 Hz
Stats 6419.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29874615 bytes_read=4655614 bytes_retransmit=9 bytes_invalid=0 send_seq=564286 receive_seq=564286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=17664 freq=400016124 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39766 bytes_read=124459 bytes_retransmit=0 bytes_invalid=0 send_seq=6599 receive_seq=6599 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999574 adj=49997417 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192898 bytes_read=6140542 bytes_retransmit=9 bytes_invalid=0 send_seq=26853 receive_seq=26853 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997468 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131692 bytes_read=3552365 bytes_retransmit=9 bytes_invalid=0 send_seq=18201 receive_seq=18201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997296 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40033 bytes_read=1638880 bytes_retransmit=9 bytes_invalid=0 send_seq=6613 receive_seq=6613 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997541 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40519 bytes_read=122025 bytes_retransmit=9 bytes_invalid=0 send_seq=6600 receive_seq=6600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999408 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94611 bytes_read=2511427 bytes_retransmit=0 bytes_invalid=0 send_seq=11159 receive_seq=11159 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998582 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.6 th2: temp=61.0 th3: temp=58.6 sysload=0.38 cputime=484.570 memavail=7394180 print_time=6444.137 buffer_time=2.190 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 86 Hz
Stats 6420.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29888489 bytes_read=4657118 bytes_retransmit=9 bytes_invalid=0 send_seq=564526 receive_seq=564526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=15222 freq=400016100 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39772 bytes_read=124475 bytes_retransmit=0 bytes_invalid=0 send_seq=6600 receive_seq=6600 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999573 adj=49997457 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192904 bytes_read=6140649 bytes_retransmit=9 bytes_invalid=0 send_seq=26854 receive_seq=26854 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997514 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131768 bytes_read=3555404 bytes_retransmit=9 bytes_invalid=0 send_seq=18212 receive_seq=18212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997345 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40039 bytes_read=1639154 bytes_retransmit=9 bytes_invalid=0 send_seq=6614 receive_seq=6614 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997573 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40525 bytes_read=122041 bytes_retransmit=9 bytes_invalid=0 send_seq=6601 receive_seq=6601 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999417 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94617 bytes_read=2511783 bytes_retransmit=0 bytes_invalid=0 send_seq=11160 receive_seq=11160 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998607 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.4 th2: temp=61.0 th3: temp=58.6 sysload=0.35 cputime=484.703 memavail=7394180 print_time=6445.015 buffer_time=2.068 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 87 Hz
Stats 6421.3: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29900342 bytes_read=4658482 bytes_retransmit=9 bytes_invalid=0 send_seq=564734 receive_seq=564734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=19199 freq=400016084 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=39778 bytes_read=124504 bytes_retransmit=0 bytes_invalid=0 send_seq=6601 receive_seq=6601 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999572 adj=49997497 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192910 bytes_read=6140742 bytes_retransmit=9 bytes_invalid=0 send_seq=26855 receive_seq=26855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997586 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131844 bytes_read=3558504 bytes_retransmit=9 bytes_invalid=0 send_seq=18223 receive_seq=18223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000047 adj=63997393 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40045 bytes_read=1639372 bytes_retransmit=9 bytes_invalid=0 send_seq=6615 receive_seq=6615 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997613 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40531 bytes_read=122057 bytes_retransmit=9 bytes_invalid=0 send_seq=6602 receive_seq=6602 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94623 bytes_read=2512155 bytes_retransmit=0 bytes_invalid=0 send_seq=11161 receive_seq=11161 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998631 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.6 th2: temp=61.0 th3: temp=58.5 sysload=0.35 cputime=484.849 memavail=7394180 print_time=6446.213 buffer_time=2.257 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 88 Hz
Stats 6422.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29914461 bytes_read=4660048 bytes_retransmit=9 bytes_invalid=0 send_seq=564979 receive_seq=564979 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=17966 freq=400016145 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=39784 bytes_read=124520 bytes_retransmit=0 bytes_invalid=0 send_seq=6602 receive_seq=6602 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999572 adj=49997533 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192916 bytes_read=6140861 bytes_retransmit=9 bytes_invalid=0 send_seq=26856 receive_seq=26856 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997631 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131920 bytes_read=3561572 bytes_retransmit=9 bytes_invalid=0 send_seq=18234 receive_seq=18234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997437 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40051 bytes_read=1639604 bytes_retransmit=9 bytes_invalid=0 send_seq=6616 receive_seq=6616 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997634 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40537 bytes_read=122084 bytes_retransmit=9 bytes_invalid=0 send_seq=6603 receive_seq=6603 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94629 bytes_read=2512495 bytes_retransmit=0 bytes_invalid=0 send_seq=11162 receive_seq=11162 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998648 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.7 th2: temp=60.8 th3: temp=58.4 sysload=0.35 cputime=484.988 memavail=7394180 print_time=6447.136 buffer_time=2.179 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 89 Hz
Stats 6423.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29929026 bytes_read=4661618 bytes_retransmit=9 bytes_invalid=0 send_seq=565231 receive_seq=565231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=15125 freq=400016143 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=39790 bytes_read=124536 bytes_retransmit=0 bytes_invalid=0 send_seq=6603 receive_seq=6603 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999571 adj=49997436 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192922 bytes_read=6140961 bytes_retransmit=9 bytes_invalid=0 send_seq=26857 receive_seq=26857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997507 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=131996 bytes_read=3564641 bytes_retransmit=9 bytes_invalid=0 send_seq=18245 receive_seq=18245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997414 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40057 bytes_read=1639864 bytes_retransmit=9 bytes_invalid=0 send_seq=6617 receive_seq=6617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997549 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40543 bytes_read=122100 bytes_retransmit=9 bytes_invalid=0 send_seq=6604 receive_seq=6604 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999410 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94635 bytes_read=2512851 bytes_retransmit=0 bytes_invalid=0 send_seq=11163 receive_seq=11163 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998584 coil_temp=17.0 refs=0 mcu_temp=20.27 supply_voltage=3.012 th0: temp=56.3 th1: temp=55.5 th2: temp=61.0 th3: temp=58.5 sysload=0.35 cputime=485.127 memavail=7394180 print_time=6448.013 buffer_time=2.055 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 90 Hz
Stats 6424.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29940821 bytes_read=4662987 bytes_retransmit=9 bytes_invalid=0 send_seq=565437 receive_seq=565437 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=19141 freq=400016124 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=39796 bytes_read=124552 bytes_retransmit=0 bytes_invalid=0 send_seq=6604 receive_seq=6604 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999571 adj=49997446 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192928 bytes_read=6141061 bytes_retransmit=9 bytes_invalid=0 send_seq=26858 receive_seq=26858 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997524 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=132072 bytes_read=3567756 bytes_retransmit=9 bytes_invalid=0 send_seq=18256 receive_seq=18256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997503 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40063 bytes_read=1640108 bytes_retransmit=9 bytes_invalid=0 send_seq=6618 receive_seq=6618 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997572 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40549 bytes_read=122116 bytes_retransmit=9 bytes_invalid=0 send_seq=6605 receive_seq=6605 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999412 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94641 bytes_read=2513223 bytes_retransmit=0 bytes_invalid=0 send_seq=11164 receive_seq=11164 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998610 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.5 th2: temp=61.0 th3: temp=58.5 sysload=0.35 cputime=485.279 memavail=7394180 print_time=6449.221 buffer_time=2.257 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 91 Hz
Stats 6425.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29955012 bytes_read=4664527 bytes_retransmit=9 bytes_invalid=0 send_seq=565683 receive_seq=565683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=18641 freq=400016100 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=39802 bytes_read=124568 bytes_retransmit=0 bytes_invalid=0 send_seq=6605 receive_seq=6605 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999569 adj=49997500 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192934 bytes_read=6141203 bytes_retransmit=9 bytes_invalid=0 send_seq=26859 receive_seq=26859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997645 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=132148 bytes_read=3570842 bytes_retransmit=9 bytes_invalid=0 send_seq=18267 receive_seq=18267 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40069 bytes_read=1640372 bytes_retransmit=9 bytes_invalid=0 send_seq=6619 receive_seq=6619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997605 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40555 bytes_read=122132 bytes_retransmit=9 bytes_invalid=0 send_seq=6606 receive_seq=6606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94647 bytes_read=2513579 bytes_retransmit=0 bytes_invalid=0 send_seq=11165 receive_seq=11165 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998634 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=56.1 th1: temp=55.6 th2: temp=60.8 th3: temp=58.6 sysload=0.32 cputime=485.415 memavail=7394176 print_time=6450.157 buffer_time=2.192 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 92 Hz
Stats 6426.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29969383 bytes_read=4666087 bytes_retransmit=9 bytes_invalid=0 send_seq=565933 receive_seq=565933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=15515 freq=400016082 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39808 bytes_read=124597 bytes_retransmit=0 bytes_invalid=0 send_seq=6606 receive_seq=6606 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999567 adj=49997524 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192940 bytes_read=6141303 bytes_retransmit=9 bytes_invalid=0 send_seq=26860 receive_seq=26860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997678 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=132224 bytes_read=3573900 bytes_retransmit=9 bytes_invalid=0 send_seq=18278 receive_seq=18278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997543 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40075 bytes_read=1640636 bytes_retransmit=9 bytes_invalid=0 send_seq=6620 receive_seq=6620 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40561 bytes_read=122148 bytes_retransmit=9 bytes_invalid=0 send_seq=6607 receive_seq=6607 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94653 bytes_read=2513919 bytes_retransmit=0 bytes_invalid=0 send_seq=11166 receive_seq=11166 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998681 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=56.3 th1: temp=55.6 th2: temp=60.9 th3: temp=58.6 sysload=0.32 cputime=485.551 memavail=7394176 print_time=6451.032 buffer_time=2.067 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 93 Hz
Stats 6427.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29981412 bytes_read=4667497 bytes_retransmit=9 bytes_invalid=0 send_seq=566144 receive_seq=566144 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=19575 freq=400016076 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39814 bytes_read=124613 bytes_retransmit=0 bytes_invalid=0 send_seq=6607 receive_seq=6607 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999567 adj=49997536 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192946 bytes_read=6141403 bytes_retransmit=9 bytes_invalid=0 send_seq=26861 receive_seq=26861 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997719 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=132300 bytes_read=3576958 bytes_retransmit=9 bytes_invalid=0 send_seq=18289 receive_seq=18289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997555 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40081 bytes_read=1640870 bytes_retransmit=9 bytes_invalid=0 send_seq=6621 receive_seq=6621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40567 bytes_read=122175 bytes_retransmit=9 bytes_invalid=0 send_seq=6608 receive_seq=6608 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94659 bytes_read=2514291 bytes_retransmit=0 bytes_invalid=0 send_seq=11167 receive_seq=11167 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998691 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.012 th0: temp=56.3 th1: temp=55.4 th2: temp=60.8 th3: temp=58.4 sysload=0.32 cputime=485.710 memavail=7394880 print_time=6452.229 buffer_time=2.255 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 94 Hz
Stats 6428.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=29995718 bytes_read=4669057 bytes_retransmit=9 bytes_invalid=0 send_seq=566394 receive_seq=566394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=19291 freq=400016065 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39820 bytes_read=124629 bytes_retransmit=0 bytes_invalid=0 send_seq=6608 receive_seq=6608 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999568 adj=49997545 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192952 bytes_read=6141531 bytes_retransmit=9 bytes_invalid=0 send_seq=26862 receive_seq=26862 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997709 toolboard_t1: mcu_awake=0.316 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=132376 bytes_read=3580060 bytes_retransmit=9 bytes_invalid=0 send_seq=18300 receive_seq=18300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997545 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40087 bytes_read=1641149 bytes_retransmit=9 bytes_invalid=0 send_seq=6622 receive_seq=6622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40573 bytes_read=122191 bytes_retransmit=9 bytes_invalid=0 send_seq=6609 receive_seq=6609 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94665 bytes_read=2514647 bytes_retransmit=0 bytes_invalid=0 send_seq=11168 receive_seq=11168 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998683 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=56.5 th1: temp=55.6 th2: temp=60.9 th3: temp=58.6 sysload=0.32 cputime=485.853 memavail=7394880 print_time=6453.161 buffer_time=2.187 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 95 Hz
Stats 6429.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30010578 bytes_read=4670652 bytes_retransmit=9 bytes_invalid=0 send_seq=566651 receive_seq=566651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=15991 freq=400016049 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39826 bytes_read=124645 bytes_retransmit=0 bytes_invalid=0 send_seq=6609 receive_seq=6609 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999567 adj=49997573 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192958 bytes_read=6141631 bytes_retransmit=9 bytes_invalid=0 send_seq=26863 receive_seq=26863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997707 toolboard_t1: mcu_awake=0.316 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=132452 bytes_read=3583175 bytes_retransmit=9 bytes_invalid=0 send_seq=18311 receive_seq=18311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40093 bytes_read=1641413 bytes_retransmit=9 bytes_invalid=0 send_seq=6623 receive_seq=6623 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40579 bytes_read=122207 bytes_retransmit=9 bytes_invalid=0 send_seq=6610 receive_seq=6610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94671 bytes_read=2515003 bytes_retransmit=0 bytes_invalid=0 send_seq=11169 receive_seq=11169 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998678 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=56.4 th1: temp=55.6 th2: temp=60.9 th3: temp=58.5 sysload=0.32 cputime=485.994 memavail=7394656 print_time=6454.025 buffer_time=2.050 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 96 Hz
Stats 6430.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30022907 bytes_read=4672059 bytes_retransmit=9 bytes_invalid=0 send_seq=566865 receive_seq=566865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=20247 freq=400016026 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39832 bytes_read=124661 bytes_retransmit=0 bytes_invalid=0 send_seq=6610 receive_seq=6610 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999566 adj=49997587 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192964 bytes_read=6141745 bytes_retransmit=9 bytes_invalid=0 send_seq=26864 receive_seq=26864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997721 toolboard_t1: mcu_awake=0.316 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=132528 bytes_read=3586234 bytes_retransmit=9 bytes_invalid=0 send_seq=18322 receive_seq=18322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997550 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40099 bytes_read=1641647 bytes_retransmit=9 bytes_invalid=0 send_seq=6624 receive_seq=6624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997690 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40585 bytes_read=122223 bytes_retransmit=9 bytes_invalid=0 send_seq=6611 receive_seq=6611 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999468 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94677 bytes_read=2515377 bytes_retransmit=0 bytes_invalid=0 send_seq=11170 receive_seq=11170 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998687 coil_temp=17.0 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=56.3 th1: temp=55.6 th2: temp=61.0 th3: temp=58.5 sysload=0.30 cputime=486.151 memavail=7394656 print_time=6455.235 buffer_time=2.248 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 97 Hz
Stats 6431.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30037581 bytes_read=4673621 bytes_retransmit=9 bytes_invalid=0 send_seq=567117 receive_seq=567116 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=19770 freq=400016018 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39838 bytes_read=124690 bytes_retransmit=0 bytes_invalid=0 send_seq=6611 receive_seq=6611 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999565 adj=49997610 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192970 bytes_read=6141873 bytes_retransmit=9 bytes_invalid=0 send_seq=26865 receive_seq=26865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997750 toolboard_t1: mcu_awake=0.316 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=132604 bytes_read=3589319 bytes_retransmit=9 bytes_invalid=0 send_seq=18333 receive_seq=18333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997580 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40105 bytes_read=1641941 bytes_retransmit=9 bytes_invalid=0 send_seq=6625 receive_seq=6625 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997703 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40591 bytes_read=122239 bytes_retransmit=9 bytes_invalid=0 send_seq=6612 receive_seq=6612 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999465 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94683 bytes_read=2515733 bytes_retransmit=0 bytes_invalid=0 send_seq=11171 receive_seq=11171 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998695 coil_temp=17.0 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=56.4 th1: temp=55.7 th2: temp=60.8 th3: temp=58.6 sysload=0.30 cputime=486.296 memavail=7394656 print_time=6456.168 buffer_time=2.179 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 98 Hz
Stats 6432.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30052853 bytes_read=4675267 bytes_retransmit=9 bytes_invalid=0 send_seq=567381 receive_seq=567380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=23 upcoming_bytes=16208 freq=400016018 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39844 bytes_read=124706 bytes_retransmit=0 bytes_invalid=0 send_seq=6612 receive_seq=6612 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999564 adj=49997604 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192976 bytes_read=6141973 bytes_retransmit=9 bytes_invalid=0 send_seq=26866 receive_seq=26866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997739 toolboard_t1: mcu_awake=0.316 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=132680 bytes_read=3592434 bytes_retransmit=9 bytes_invalid=0 send_seq=18344 receive_seq=18344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40111 bytes_read=1642175 bytes_retransmit=9 bytes_invalid=0 send_seq=6626 receive_seq=6626 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997698 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40597 bytes_read=122266 bytes_retransmit=9 bytes_invalid=0 send_seq=6613 receive_seq=6613 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94689 bytes_read=2516089 bytes_retransmit=0 bytes_invalid=0 send_seq=11172 receive_seq=11172 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998694 coil_temp=17.0 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=56.3 th1: temp=55.6 th2: temp=60.8 th3: temp=58.6 sysload=0.30 cputime=486.435 memavail=7394656 print_time=6457.040 buffer_time=2.052 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 99 Hz
Stats 6433.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30065303 bytes_read=4676706 bytes_retransmit=9 bytes_invalid=0 send_seq=567600 receive_seq=567600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=20361 freq=400016019 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39850 bytes_read=124722 bytes_retransmit=0 bytes_invalid=0 send_seq=6613 receive_seq=6613 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999563 adj=49997579 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192982 bytes_read=6142073 bytes_retransmit=9 bytes_invalid=0 send_seq=26867 receive_seq=26867 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997722 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=132756 bytes_read=3595509 bytes_retransmit=9 bytes_invalid=0 send_seq=18355 receive_seq=18355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40117 bytes_read=1642409 bytes_retransmit=9 bytes_invalid=0 send_seq=6627 receive_seq=6627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997705 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40603 bytes_read=122282 bytes_retransmit=9 bytes_invalid=0 send_seq=6614 receive_seq=6614 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94695 bytes_read=2516445 bytes_retransmit=0 bytes_invalid=0 send_seq=11173 receive_seq=11173 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998679 coil_temp=17.0 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=56.6 th1: temp=55.5 th2: temp=61.2 th3: temp=58.6 sysload=0.30 cputime=486.587 memavail=7394656 print_time=6458.237 buffer_time=2.247 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 100 Hz
Stats 6434.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30080032 bytes_read=4678281 bytes_retransmit=9 bytes_invalid=0 send_seq=567853 receive_seq=567853 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=20035 freq=400016012 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39856 bytes_read=124738 bytes_retransmit=0 bytes_invalid=0 send_seq=6614 receive_seq=6614 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999563 adj=49997568 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=192988 bytes_read=6142201 bytes_retransmit=9 bytes_invalid=0 send_seq=26868 receive_seq=26868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997779 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=132825 bytes_read=3598575 bytes_retransmit=9 bytes_invalid=0 send_seq=18365 receive_seq=18365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997614 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40123 bytes_read=1642718 bytes_retransmit=9 bytes_invalid=0 send_seq=6628 receive_seq=6628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40609 bytes_read=122298 bytes_retransmit=9 bytes_invalid=0 send_seq=6615 receive_seq=6615 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94701 bytes_read=2516801 bytes_retransmit=0 bytes_invalid=0 send_seq=11174 receive_seq=11174 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998674 coil_temp=17.0 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=56.4 th1: temp=55.5 th2: temp=61.0 th3: temp=58.5 sysload=0.30 cputime=486.725 memavail=7394656 print_time=6459.171 buffer_time=2.181 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 101 Hz
Stats 6435.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30095266 bytes_read=4679916 bytes_retransmit=9 bytes_invalid=0 send_seq=568118 receive_seq=568118 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=16679 freq=400015992 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39862 bytes_read=124754 bytes_retransmit=0 bytes_invalid=0 send_seq=6615 receive_seq=6615 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999563 adj=49997574 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=192994 bytes_read=6142315 bytes_retransmit=9 bytes_invalid=0 send_seq=26869 receive_seq=26869 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997851 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=132901 bytes_read=3601633 bytes_retransmit=9 bytes_invalid=0 send_seq=18376 receive_seq=18376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997591 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40129 bytes_read=1642952 bytes_retransmit=9 bytes_invalid=0 send_seq=6629 receive_seq=6629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997690 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40615 bytes_read=122314 bytes_retransmit=9 bytes_invalid=0 send_seq=6616 receive_seq=6616 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94707 bytes_read=2517157 bytes_retransmit=0 bytes_invalid=0 send_seq=11175 receive_seq=11175 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998676 coil_temp=17.0 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.7 th2: temp=61.1 th3: temp=58.7 sysload=0.27 cputime=486.865 memavail=7394656 print_time=6460.045 buffer_time=2.054 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 102 Hz
Stats 6436.3: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30108275 bytes_read=4681395 bytes_retransmit=9 bytes_invalid=0 send_seq=568346 receive_seq=568346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=20729 freq=400015974 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39868 bytes_read=124783 bytes_retransmit=0 bytes_invalid=0 send_seq=6616 receive_seq=6616 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999562 adj=49997600 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193000 bytes_read=6142415 bytes_retransmit=9 bytes_invalid=0 send_seq=26870 receive_seq=26870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63998007 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=132977 bytes_read=3604689 bytes_retransmit=9 bytes_invalid=0 send_seq=18387 receive_seq=18387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997597 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40135 bytes_read=1643186 bytes_retransmit=9 bytes_invalid=0 send_seq=6630 receive_seq=6630 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997713 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40621 bytes_read=122330 bytes_retransmit=9 bytes_invalid=0 send_seq=6617 receive_seq=6617 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94713 bytes_read=2517513 bytes_retransmit=0 bytes_invalid=0 send_seq=11176 receive_seq=11176 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998698 coil_temp=17.0 refs=0 mcu_temp=20.21 supply_voltage=3.012 th0: temp=56.1 th1: temp=55.5 th2: temp=60.9 th3: temp=58.6 sysload=0.27 cputime=487.017 memavail=7394656 print_time=6461.250 buffer_time=2.255 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 103 Hz
Stats 6437.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30122987 bytes_read=4682981 bytes_retransmit=9 bytes_invalid=0 send_seq=568598 receive_seq=568598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=20888 freq=400015966 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39874 bytes_read=124799 bytes_retransmit=0 bytes_invalid=0 send_seq=6617 receive_seq=6617 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999561 adj=49997601 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193006 bytes_read=6142543 bytes_retransmit=9 bytes_invalid=0 send_seq=26871 receive_seq=26871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997917 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133053 bytes_read=3607773 bytes_retransmit=9 bytes_invalid=0 send_seq=18398 receive_seq=18398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997584 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40141 bytes_read=1643480 bytes_retransmit=9 bytes_invalid=0 send_seq=6631 receive_seq=6631 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997706 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40627 bytes_read=122357 bytes_retransmit=9 bytes_invalid=0 send_seq=6618 receive_seq=6618 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94719 bytes_read=2517869 bytes_retransmit=0 bytes_invalid=0 send_seq=11177 receive_seq=11177 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998750 coil_temp=17.0 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.6 th2: temp=61.0 th3: temp=58.6 sysload=0.27 cputime=487.160 memavail=7394404 print_time=6462.182 buffer_time=2.185 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 104 Hz
Stats 6438.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30138536 bytes_read=4684631 bytes_retransmit=9 bytes_invalid=0 send_seq=568866 receive_seq=568866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=17352 freq=400015949 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39880 bytes_read=124815 bytes_retransmit=0 bytes_invalid=0 send_seq=6618 receive_seq=6618 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999560 adj=49997600 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193012 bytes_read=6142643 bytes_retransmit=9 bytes_invalid=0 send_seq=26872 receive_seq=26872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000239 adj=63997873 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133129 bytes_read=3610904 bytes_retransmit=9 bytes_invalid=0 send_seq=18409 receive_seq=18409 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000074 adj=63997702 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40147 bytes_read=1643714 bytes_retransmit=9 bytes_invalid=0 send_seq=6632 receive_seq=6632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40633 bytes_read=122373 bytes_retransmit=9 bytes_invalid=0 send_seq=6619 receive_seq=6619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94725 bytes_read=2518225 bytes_retransmit=0 bytes_invalid=0 send_seq=11178 receive_seq=11178 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998737 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.5 th2: temp=61.1 th3: temp=58.4 sysload=0.27 cputime=487.302 memavail=7394428 print_time=6463.054 buffer_time=2.058 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 105 Hz
Stats 6439.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30151869 bytes_read=4686135 bytes_retransmit=9 bytes_invalid=0 send_seq=569099 receive_seq=569099 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=21386 freq=400015938 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39886 bytes_read=124831 bytes_retransmit=0 bytes_invalid=0 send_seq=6619 receive_seq=6619 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999559 adj=49997616 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193018 bytes_read=6142757 bytes_retransmit=9 bytes_invalid=0 send_seq=26873 receive_seq=26873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997979 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133205 bytes_read=3613962 bytes_retransmit=9 bytes_invalid=0 send_seq=18420 receive_seq=18420 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997857 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40153 bytes_read=1643963 bytes_retransmit=9 bytes_invalid=0 send_seq=6633 receive_seq=6633 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997710 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40639 bytes_read=122389 bytes_retransmit=9 bytes_invalid=0 send_seq=6620 receive_seq=6620 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94731 bytes_read=2518581 bytes_retransmit=0 bytes_invalid=0 send_seq=11179 receive_seq=11179 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998740 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.6 th2: temp=61.0 th3: temp=58.5 sysload=0.27 cputime=487.456 memavail=7394428 print_time=6464.249 buffer_time=2.246 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 106 Hz
Stats 6440.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30166983 bytes_read=4687745 bytes_retransmit=9 bytes_invalid=0 send_seq=569359 receive_seq=569359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=21402 freq=400015924 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39892 bytes_read=124847 bytes_retransmit=0 bytes_invalid=0 send_seq=6620 receive_seq=6620 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999559 adj=49997603 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193024 bytes_read=6142885 bytes_retransmit=9 bytes_invalid=0 send_seq=26874 receive_seq=26874 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997896 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133281 bytes_read=3617047 bytes_retransmit=9 bytes_invalid=0 send_seq=18431 receive_seq=18431 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997761 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40159 bytes_read=1644257 bytes_retransmit=9 bytes_invalid=0 send_seq=6634 receive_seq=6634 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997720 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40645 bytes_read=122405 bytes_retransmit=9 bytes_invalid=0 send_seq=6621 receive_seq=6621 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94737 bytes_read=2518937 bytes_retransmit=0 bytes_invalid=0 send_seq=11180 receive_seq=11180 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998727 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.7 th2: temp=60.9 th3: temp=58.6 sysload=0.25 cputime=487.598 memavail=7394428 print_time=6465.187 buffer_time=2.183 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 107 Hz
Stats 6441.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30182972 bytes_read=4689433 bytes_retransmit=9 bytes_invalid=0 send_seq=569635 receive_seq=569635 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=52 upcoming_bytes=17648 freq=400015921 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39898 bytes_read=124876 bytes_retransmit=0 bytes_invalid=0 send_seq=6621 receive_seq=6621 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999559 adj=49997621 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193030 bytes_read=6142985 bytes_retransmit=9 bytes_invalid=0 send_seq=26875 receive_seq=26875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997875 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133357 bytes_read=3620104 bytes_retransmit=9 bytes_invalid=0 send_seq=18442 receive_seq=18442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997723 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40165 bytes_read=1644491 bytes_retransmit=9 bytes_invalid=0 send_seq=6635 receive_seq=6635 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997721 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40651 bytes_read=122421 bytes_retransmit=9 bytes_invalid=0 send_seq=6622 receive_seq=6622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94743 bytes_read=2519293 bytes_retransmit=0 bytes_invalid=0 send_seq=11181 receive_seq=11181 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998730 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.6 th2: temp=61.1 th3: temp=58.7 sysload=0.25 cputime=487.742 memavail=7394428 print_time=6466.058 buffer_time=2.054 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 108 Hz
Stats 6442.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30196443 bytes_read=4690965 bytes_retransmit=9 bytes_invalid=0 send_seq=569871 receive_seq=569871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=21965 freq=400015915 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39904 bytes_read=124892 bytes_retransmit=0 bytes_invalid=0 send_seq=6622 receive_seq=6622 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999559 adj=49997616 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193036 bytes_read=6143099 bytes_retransmit=9 bytes_invalid=0 send_seq=26876 receive_seq=26876 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997831 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133433 bytes_read=3623164 bytes_retransmit=9 bytes_invalid=0 send_seq=18453 receive_seq=18453 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997676 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40171 bytes_read=1644725 bytes_retransmit=9 bytes_invalid=0 send_seq=6636 receive_seq=6636 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997715 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40657 bytes_read=122448 bytes_retransmit=9 bytes_invalid=0 send_seq=6623 receive_seq=6623 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94749 bytes_read=2519649 bytes_retransmit=0 bytes_invalid=0 send_seq=11182 receive_seq=11182 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998718 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.6 th2: temp=61.0 th3: temp=58.5 sysload=0.25 cputime=487.906 memavail=7394432 print_time=6467.261 buffer_time=2.257 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 109 Hz
Stats 6443.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30211674 bytes_read=4692585 bytes_retransmit=9 bytes_invalid=0 send_seq=570133 receive_seq=570133 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=21975 freq=400015899 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39910 bytes_read=124908 bytes_retransmit=0 bytes_invalid=0 send_seq=6623 receive_seq=6623 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999558 adj=49997607 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193042 bytes_read=6143213 bytes_retransmit=9 bytes_invalid=0 send_seq=26877 receive_seq=26877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997770 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133509 bytes_read=3626323 bytes_retransmit=9 bytes_invalid=0 send_seq=18464 receive_seq=18464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997626 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40177 bytes_read=1645019 bytes_retransmit=9 bytes_invalid=0 send_seq=6637 receive_seq=6637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997698 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40663 bytes_read=122464 bytes_retransmit=9 bytes_invalid=0 send_seq=6624 receive_seq=6624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94755 bytes_read=2520005 bytes_retransmit=0 bytes_invalid=0 send_seq=11183 receive_seq=11183 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998703 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.5 th2: temp=61.0 th3: temp=58.7 sysload=0.25 cputime=488.056 memavail=7394432 print_time=6468.187 buffer_time=2.182 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 110 Hz
Stats 6444.3: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30228064 bytes_read=4694300 bytes_retransmit=9 bytes_invalid=0 send_seq=570414 receive_seq=570414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=18140 freq=400015907 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39916 bytes_read=124924 bytes_retransmit=0 bytes_invalid=0 send_seq=6624 receive_seq=6624 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999557 adj=49997619 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193048 bytes_read=6143313 bytes_retransmit=9 bytes_invalid=0 send_seq=26878 receive_seq=26878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997767 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133585 bytes_read=3629379 bytes_retransmit=9 bytes_invalid=0 send_seq=18475 receive_seq=18475 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997618 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40183 bytes_read=1645268 bytes_retransmit=9 bytes_invalid=0 send_seq=6638 receive_seq=6638 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997710 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40669 bytes_read=122480 bytes_retransmit=9 bytes_invalid=0 send_seq=6625 receive_seq=6625 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94761 bytes_read=2520361 bytes_retransmit=0 bytes_invalid=0 send_seq=11184 receive_seq=11184 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998732 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.6 th2: temp=61.0 th3: temp=58.6 sysload=0.25 cputime=488.215 memavail=7394556 print_time=6469.064 buffer_time=2.059 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 111 Hz
Stats 6445.4: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30241816 bytes_read=4695844 bytes_retransmit=9 bytes_invalid=0 send_seq=570655 receive_seq=570655 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=22228 freq=400015901 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=39922 bytes_read=124940 bytes_retransmit=0 bytes_invalid=0 send_seq=6625 receive_seq=6625 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999556 adj=49997591 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193054 bytes_read=6143441 bytes_retransmit=9 bytes_invalid=0 send_seq=26879 receive_seq=26879 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997720 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133661 bytes_read=3632438 bytes_retransmit=9 bytes_invalid=0 send_seq=18486 receive_seq=18486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997584 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40189 bytes_read=1645502 bytes_retransmit=9 bytes_invalid=0 send_seq=6639 receive_seq=6639 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40675 bytes_read=122496 bytes_retransmit=9 bytes_invalid=0 send_seq=6626 receive_seq=6626 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94767 bytes_read=2520717 bytes_retransmit=0 bytes_invalid=0 send_seq=11185 receive_seq=11185 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998704 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.7 th2: temp=61.0 th3: temp=58.6 sysload=0.23 cputime=488.371 memavail=7394332 print_time=6470.260 buffer_time=2.254 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 112 Hz
Stats 6446.4: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30257302 bytes_read=4697489 bytes_retransmit=9 bytes_invalid=0 send_seq=570922 receive_seq=570922 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=22152 freq=400015906 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39928 bytes_read=124969 bytes_retransmit=0 bytes_invalid=0 send_seq=6626 receive_seq=6626 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999556 adj=49997575 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193060 bytes_read=6143555 bytes_retransmit=9 bytes_invalid=0 send_seq=26880 receive_seq=26880 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997702 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133737 bytes_read=3635522 bytes_retransmit=9 bytes_invalid=0 send_seq=18497 receive_seq=18497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997560 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40195 bytes_read=1645796 bytes_retransmit=9 bytes_invalid=0 send_seq=6640 receive_seq=6640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997677 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40681 bytes_read=122512 bytes_retransmit=9 bytes_invalid=0 send_seq=6627 receive_seq=6627 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94773 bytes_read=2521073 bytes_retransmit=0 bytes_invalid=0 send_seq=11186 receive_seq=11186 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998695 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.7 th2: temp=61.1 th3: temp=58.7 sysload=0.23 cputime=488.515 memavail=7394332 print_time=6471.185 buffer_time=2.178 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 113 Hz
Stats 6447.4: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30273828 bytes_read=4699230 bytes_retransmit=9 bytes_invalid=0 send_seq=571205 receive_seq=571205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=18204 freq=400015887 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39934 bytes_read=124985 bytes_retransmit=0 bytes_invalid=0 send_seq=6627 receive_seq=6627 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999556 adj=49997565 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193066 bytes_read=6143655 bytes_retransmit=9 bytes_invalid=0 send_seq=26881 receive_seq=26881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997667 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133806 bytes_read=3638555 bytes_retransmit=9 bytes_invalid=0 send_seq=18507 receive_seq=18507 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997521 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40201 bytes_read=1646030 bytes_retransmit=9 bytes_invalid=0 send_seq=6641 receive_seq=6641 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40687 bytes_read=122539 bytes_retransmit=9 bytes_invalid=0 send_seq=6628 receive_seq=6628 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94779 bytes_read=2521429 bytes_retransmit=0 bytes_invalid=0 send_seq=11187 receive_seq=11187 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998701 coil_temp=17.0 refs=0 mcu_temp=20.25 supply_voltage=3.012 th0: temp=56.3 th1: temp=55.5 th2: temp=61.1 th3: temp=58.7 sysload=0.23 cputime=488.662 memavail=7394096 print_time=6472.068 buffer_time=2.061 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 114 Hz
Stats 6448.4: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30287829 bytes_read=4700789 bytes_retransmit=9 bytes_invalid=0 send_seq=571449 receive_seq=571449 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=22347 freq=400015873 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39940 bytes_read=125001 bytes_retransmit=0 bytes_invalid=0 send_seq=6628 receive_seq=6628 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999556 adj=49997607 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193072 bytes_read=6143769 bytes_retransmit=9 bytes_invalid=0 send_seq=26882 receive_seq=26882 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997683 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133882 bytes_read=3641631 bytes_retransmit=9 bytes_invalid=0 send_seq=18518 receive_seq=18518 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997534 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40207 bytes_read=1646264 bytes_retransmit=9 bytes_invalid=0 send_seq=6642 receive_seq=6642 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40693 bytes_read=122555 bytes_retransmit=9 bytes_invalid=0 send_seq=6629 receive_seq=6629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94785 bytes_read=2521785 bytes_retransmit=0 bytes_invalid=0 send_seq=11188 receive_seq=11188 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998770 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=56.3 th1: temp=55.8 th2: temp=61.0 th3: temp=58.7 sysload=0.23 cputime=488.822 memavail=7394104 print_time=6473.271 buffer_time=2.257 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 115 Hz
Stats 6449.4: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30303120 bytes_read=4702409 bytes_retransmit=9 bytes_invalid=0 send_seq=571711 receive_seq=571711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=22940 freq=400015869 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39946 bytes_read=125017 bytes_retransmit=0 bytes_invalid=0 send_seq=6629 receive_seq=6629 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999556 adj=49997617 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193078 bytes_read=6143883 bytes_retransmit=9 bytes_invalid=0 send_seq=26883 receive_seq=26883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997694 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=133958 bytes_read=3644775 bytes_retransmit=9 bytes_invalid=0 send_seq=18529 receive_seq=18529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997535 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40213 bytes_read=1646573 bytes_retransmit=9 bytes_invalid=0 send_seq=6643 receive_seq=6643 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997690 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40699 bytes_read=122571 bytes_retransmit=9 bytes_invalid=0 send_seq=6630 receive_seq=6630 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94791 bytes_read=2522141 bytes_retransmit=0 bytes_invalid=0 send_seq=11189 receive_seq=11189 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998744 coil_temp=17.0 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=56.1 th1: temp=55.7 th2: temp=61.1 th3: temp=58.6 sysload=0.23 cputime=488.968 memavail=7394104 print_time=6474.201 buffer_time=2.186 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 116 Hz
Stats 6450.4: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30319849 bytes_read=4704149 bytes_retransmit=9 bytes_invalid=0 send_seq=571997 receive_seq=571997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=52 upcoming_bytes=18968 freq=400015875 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39952 bytes_read=125033 bytes_retransmit=0 bytes_invalid=0 send_seq=6630 receive_seq=6630 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999556 adj=49997615 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193084 bytes_read=6143983 bytes_retransmit=9 bytes_invalid=0 send_seq=26884 receive_seq=26884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997684 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134034 bytes_read=3647834 bytes_retransmit=9 bytes_invalid=0 send_seq=18540 receive_seq=18540 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997526 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40219 bytes_read=1646807 bytes_retransmit=9 bytes_invalid=0 send_seq=6644 receive_seq=6644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40705 bytes_read=122587 bytes_retransmit=9 bytes_invalid=0 send_seq=6631 receive_seq=6631 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94797 bytes_read=2522497 bytes_retransmit=0 bytes_invalid=0 send_seq=11190 receive_seq=11190 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998737 coil_temp=17.0 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=56.3 th1: temp=55.5 th2: temp=60.8 th3: temp=58.7 sysload=0.21 cputime=489.115 memavail=7394104 print_time=6475.078 buffer_time=2.063 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 117 Hz
Stats 6451.4: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30334334 bytes_read=4705738 bytes_retransmit=9 bytes_invalid=0 send_seq=572247 receive_seq=572247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=22808 freq=400015867 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39958 bytes_read=125048 bytes_retransmit=0 bytes_invalid=0 send_seq=6631 receive_seq=6631 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999554 adj=49997596 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193090 bytes_read=6144125 bytes_retransmit=9 bytes_invalid=0 send_seq=26885 receive_seq=26885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997678 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134110 bytes_read=3650908 bytes_retransmit=9 bytes_invalid=0 send_seq=18551 receive_seq=18551 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997513 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40225 bytes_read=1647041 bytes_retransmit=9 bytes_invalid=0 send_seq=6645 receive_seq=6645 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40711 bytes_read=122603 bytes_retransmit=9 bytes_invalid=0 send_seq=6632 receive_seq=6632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94803 bytes_read=2522853 bytes_retransmit=0 bytes_invalid=0 send_seq=11191 receive_seq=11191 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998711 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.8 th2: temp=61.0 th3: temp=58.6 sysload=0.21 cputime=489.277 memavail=7394120 print_time=6476.274 buffer_time=2.254 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 118 Hz
Stats 6452.4: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30349986 bytes_read=4707403 bytes_retransmit=9 bytes_invalid=0 send_seq=572516 receive_seq=572516 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=29 upcoming_bytes=23367 freq=400015869 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39964 bytes_read=125076 bytes_retransmit=0 bytes_invalid=0 send_seq=6632 receive_seq=6632 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999553 adj=49997585 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193096 bytes_read=6144225 bytes_retransmit=9 bytes_invalid=0 send_seq=26886 receive_seq=26886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997682 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134186 bytes_read=3653979 bytes_retransmit=9 bytes_invalid=0 send_seq=18562 receive_seq=18562 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40231 bytes_read=1647335 bytes_retransmit=9 bytes_invalid=0 send_seq=6646 receive_seq=6646 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40717 bytes_read=122630 bytes_retransmit=9 bytes_invalid=0 send_seq=6633 receive_seq=6633 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94809 bytes_read=2523209 bytes_retransmit=0 bytes_invalid=0 send_seq=11192 receive_seq=11192 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998707 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.3 th1: temp=56.0 th2: temp=61.1 th3: temp=58.6 sysload=0.21 cputime=489.423 memavail=7394120 print_time=6477.205 buffer_time=2.185 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 119 Hz
Stats 6453.4: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30366918 bytes_read=4709157 bytes_retransmit=9 bytes_invalid=0 send_seq=572805 receive_seq=572805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=19000 freq=400015867 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39970 bytes_read=125091 bytes_retransmit=0 bytes_invalid=0 send_seq=6633 receive_seq=6633 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999553 adj=49997563 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193102 bytes_read=6144325 bytes_retransmit=9 bytes_invalid=0 send_seq=26887 receive_seq=26887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997664 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134262 bytes_read=3657054 bytes_retransmit=9 bytes_invalid=0 send_seq=18573 receive_seq=18573 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997487 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40237 bytes_read=1647569 bytes_retransmit=9 bytes_invalid=0 send_seq=6647 receive_seq=6647 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40723 bytes_read=122646 bytes_retransmit=9 bytes_invalid=0 send_seq=6634 receive_seq=6634 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94815 bytes_read=2523565 bytes_retransmit=0 bytes_invalid=0 send_seq=11193 receive_seq=11193 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998701 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.9 th1: temp=55.8 th2: temp=61.0 th3: temp=58.6 sysload=0.21 cputime=489.573 memavail=7394120 print_time=6478.077 buffer_time=2.056 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 120 Hz
Stats 6454.4: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30381608 bytes_read=4710792 bytes_retransmit=9 bytes_invalid=0 send_seq=573062 receive_seq=573062 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=22889 freq=400015857 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39982 bytes_read=125121 bytes_retransmit=0 bytes_invalid=0 send_seq=6635 receive_seq=6635 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999553 adj=49997561 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193114 bytes_read=6144469 bytes_retransmit=9 bytes_invalid=0 send_seq=26889 receive_seq=26889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997656 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134344 bytes_read=3660200 bytes_retransmit=9 bytes_invalid=0 send_seq=18585 receive_seq=18585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40249 bytes_read=1647834 bytes_retransmit=9 bytes_invalid=0 send_seq=6649 receive_seq=6649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40735 bytes_read=122678 bytes_retransmit=9 bytes_invalid=0 send_seq=6636 receive_seq=6636 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94827 bytes_read=2523937 bytes_retransmit=0 bytes_invalid=0 send_seq=11195 receive_seq=11195 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998691 coil_temp=17.0 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.6 th1: temp=55.9 th2: temp=61.0 th3: temp=58.6 sysload=0.21 cputime=489.740 memavail=7394120 print_time=6479.280 buffer_time=2.259 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 121 Hz
Stats 6455.4: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30397126 bytes_read=4712437 bytes_retransmit=9 bytes_invalid=0 send_seq=573329 receive_seq=573329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=23684 freq=400015938 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39988 bytes_read=125136 bytes_retransmit=0 bytes_invalid=0 send_seq=6636 receive_seq=6636 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999552 adj=49997578 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193120 bytes_read=6144569 bytes_retransmit=9 bytes_invalid=0 send_seq=26890 receive_seq=26890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997671 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134420 bytes_read=3663271 bytes_retransmit=9 bytes_invalid=0 send_seq=18596 receive_seq=18596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997600 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40255 bytes_read=1648128 bytes_retransmit=9 bytes_invalid=0 send_seq=6650 receive_seq=6650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997679 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40741 bytes_read=122694 bytes_retransmit=9 bytes_invalid=0 send_seq=6637 receive_seq=6637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94833 bytes_read=2524277 bytes_retransmit=0 bytes_invalid=0 send_seq=11196 receive_seq=11196 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998675 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.6 th2: temp=60.9 th3: temp=58.6 sysload=0.20 cputime=489.890 memavail=7393868 print_time=6480.205 buffer_time=2.183 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 122 Hz
Stats 6456.4: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30414296 bytes_read=4714227 bytes_retransmit=9 bytes_invalid=0 send_seq=573625 receive_seq=573625 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=19260 freq=400015932 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=39994 bytes_read=125152 bytes_retransmit=0 bytes_invalid=0 send_seq=6637 receive_seq=6637 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999551 adj=49997448 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193126 bytes_read=6144683 bytes_retransmit=9 bytes_invalid=0 send_seq=26891 receive_seq=26891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997506 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134496 bytes_read=3666330 bytes_retransmit=9 bytes_invalid=0 send_seq=18607 receive_seq=18607 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997436 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40261 bytes_read=1648362 bytes_retransmit=9 bytes_invalid=0 send_seq=6651 receive_seq=6651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997557 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40747 bytes_read=122710 bytes_retransmit=9 bytes_invalid=0 send_seq=6638 receive_seq=6638 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94839 bytes_read=2524633 bytes_retransmit=0 bytes_invalid=0 send_seq=11197 receive_seq=11197 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998584 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.5 th2: temp=61.0 th3: temp=58.7 sysload=0.20 cputime=490.042 memavail=7393868 print_time=6481.076 buffer_time=2.052 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 123 Hz
Stats 6457.4: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30429202 bytes_read=4715862 bytes_retransmit=9 bytes_invalid=0 send_seq=573881 receive_seq=573881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=23323 freq=400015924 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40000 bytes_read=125181 bytes_retransmit=0 bytes_invalid=0 send_seq=6638 receive_seq=6638 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999550 adj=49997455 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193132 bytes_read=6144811 bytes_retransmit=9 bytes_invalid=0 send_seq=26892 receive_seq=26892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997531 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134572 bytes_read=3669405 bytes_retransmit=9 bytes_invalid=0 send_seq=18618 receive_seq=18618 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997435 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40267 bytes_read=1648596 bytes_retransmit=9 bytes_invalid=0 send_seq=6652 receive_seq=6652 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997584 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40753 bytes_read=122737 bytes_retransmit=9 bytes_invalid=0 send_seq=6639 receive_seq=6639 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94845 bytes_read=2524989 bytes_retransmit=0 bytes_invalid=0 send_seq=11198 receive_seq=11198 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998598 coil_temp=17.0 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.7 th2: temp=61.1 th3: temp=58.6 sysload=0.20 cputime=490.207 memavail=7392860 print_time=6482.280 buffer_time=2.255 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 124 Hz
Stats 6458.4: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30444827 bytes_read=4717487 bytes_retransmit=9 bytes_invalid=0 send_seq=574144 receive_seq=574144 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=24084 freq=400015915 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40006 bytes_read=125197 bytes_retransmit=0 bytes_invalid=0 send_seq=6639 receive_seq=6639 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999548 adj=49997487 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193138 bytes_read=6144911 bytes_retransmit=9 bytes_invalid=0 send_seq=26893 receive_seq=26893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997600 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134648 bytes_read=3672494 bytes_retransmit=9 bytes_invalid=0 send_seq=18629 receive_seq=18629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997535 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40273 bytes_read=1648890 bytes_retransmit=9 bytes_invalid=0 send_seq=6653 receive_seq=6653 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40759 bytes_read=122753 bytes_retransmit=9 bytes_invalid=0 send_seq=6640 receive_seq=6640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94851 bytes_read=2525345 bytes_retransmit=0 bytes_invalid=0 send_seq=11199 receive_seq=11199 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998618 coil_temp=17.0 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.6 th2: temp=61.2 th3: temp=58.7 sysload=0.20 cputime=490.356 memavail=7392888 print_time=6483.207 buffer_time=2.180 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 125 Hz
Stats 6459.4: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30462373 bytes_read=4719302 bytes_retransmit=9 bytes_invalid=0 send_seq=574445 receive_seq=574445 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=19420 freq=400015908 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40012 bytes_read=125213 bytes_retransmit=0 bytes_invalid=0 send_seq=6640 receive_seq=6640 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999548 adj=49997491 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193144 bytes_read=6145011 bytes_retransmit=9 bytes_invalid=0 send_seq=26894 receive_seq=26894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997632 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134717 bytes_read=3675528 bytes_retransmit=9 bytes_invalid=0 send_seq=18639 receive_seq=18639 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997530 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40279 bytes_read=1649139 bytes_retransmit=9 bytes_invalid=0 send_seq=6654 receive_seq=6654 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997677 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40765 bytes_read=122769 bytes_retransmit=9 bytes_invalid=0 send_seq=6641 receive_seq=6641 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94857 bytes_read=2525701 bytes_retransmit=0 bytes_invalid=0 send_seq=11200 receive_seq=11200 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998621 coil_temp=17.0 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.7 th2: temp=61.1 th3: temp=58.7 sysload=0.20 cputime=490.513 memavail=7392896 print_time=6484.083 buffer_time=2.055 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 126 Hz
Stats 6460.4: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30477560 bytes_read=4720941 bytes_retransmit=9 bytes_invalid=0 send_seq=574705 receive_seq=574705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=23092 freq=400015915 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40018 bytes_read=125229 bytes_retransmit=0 bytes_invalid=0 send_seq=6641 receive_seq=6641 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999549 adj=49997509 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193150 bytes_read=6145139 bytes_retransmit=9 bytes_invalid=0 send_seq=26895 receive_seq=26895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997642 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134793 bytes_read=3678657 bytes_retransmit=9 bytes_invalid=0 send_seq=18650 receive_seq=18650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997526 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40285 bytes_read=1649373 bytes_retransmit=9 bytes_invalid=0 send_seq=6655 receive_seq=6655 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997711 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40771 bytes_read=122785 bytes_retransmit=9 bytes_invalid=0 send_seq=6642 receive_seq=6642 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94863 bytes_read=2526057 bytes_retransmit=0 bytes_invalid=0 send_seq=11201 receive_seq=11201 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998623 coil_temp=17.0 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.7 th2: temp=61.0 th3: temp=58.7 sysload=0.18 cputime=490.686 memavail=7392896 print_time=6485.282 buffer_time=2.251 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 127 Hz
Stats 6461.4: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30493068 bytes_read=4722581 bytes_retransmit=9 bytes_invalid=0 send_seq=574971 receive_seq=574971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=24167 freq=400015904 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40024 bytes_read=125245 bytes_retransmit=0 bytes_invalid=0 send_seq=6642 receive_seq=6642 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999549 adj=49997527 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193156 bytes_read=6145253 bytes_retransmit=9 bytes_invalid=0 send_seq=26896 receive_seq=26896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997651 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134869 bytes_read=3681729 bytes_retransmit=9 bytes_invalid=0 send_seq=18661 receive_seq=18661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40291 bytes_read=1649667 bytes_retransmit=9 bytes_invalid=0 send_seq=6656 receive_seq=6656 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997690 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40777 bytes_read=122801 bytes_retransmit=9 bytes_invalid=0 send_seq=6643 receive_seq=6643 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94869 bytes_read=2526413 bytes_retransmit=0 bytes_invalid=0 send_seq=11202 receive_seq=11202 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998627 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.7 th2: temp=61.1 th3: temp=58.7 sysload=0.18 cputime=490.851 memavail=7387616 print_time=6486.212 buffer_time=2.180 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 128 Hz
Stats 6462.4: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30510523 bytes_read=4724402 bytes_retransmit=9 bytes_invalid=0 send_seq=575270 receive_seq=575270 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=19656 freq=400015905 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40030 bytes_read=125274 bytes_retransmit=0 bytes_invalid=0 send_seq=6643 receive_seq=6643 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999549 adj=49997545 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193162 bytes_read=6145353 bytes_retransmit=9 bytes_invalid=0 send_seq=26897 receive_seq=26897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997668 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=134945 bytes_read=3684787 bytes_retransmit=9 bytes_invalid=0 send_seq=18672 receive_seq=18672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997521 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40297 bytes_read=1649901 bytes_retransmit=9 bytes_invalid=0 send_seq=6657 receive_seq=6657 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997693 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40783 bytes_read=122828 bytes_retransmit=9 bytes_invalid=0 send_seq=6644 receive_seq=6644 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94875 bytes_read=2526769 bytes_retransmit=0 bytes_invalid=0 send_seq=11203 receive_seq=11203 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998645 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.5 th2: temp=61.2 th3: temp=58.6 sysload=0.18 cputime=491.010 memavail=7393764 print_time=6487.083 buffer_time=2.051 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 129 Hz
Stats 6463.4: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30525863 bytes_read=4726036 bytes_retransmit=9 bytes_invalid=0 send_seq=575532 receive_seq=575530 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=23541 freq=400015908 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40036 bytes_read=125290 bytes_retransmit=0 bytes_invalid=0 send_seq=6644 receive_seq=6644 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999549 adj=49997541 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193168 bytes_read=6145481 bytes_retransmit=9 bytes_invalid=0 send_seq=26898 receive_seq=26898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997742 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135021 bytes_read=3687889 bytes_retransmit=9 bytes_invalid=0 send_seq=18683 receive_seq=18683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997499 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40303 bytes_read=1650135 bytes_retransmit=9 bytes_invalid=0 send_seq=6658 receive_seq=6658 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40789 bytes_read=122844 bytes_retransmit=9 bytes_invalid=0 send_seq=6645 receive_seq=6645 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94881 bytes_read=2527125 bytes_retransmit=0 bytes_invalid=0 send_seq=11204 receive_seq=11204 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998643 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.6 th2: temp=61.3 th3: temp=58.6 sysload=0.18 cputime=491.181 memavail=7393768 print_time=6488.290 buffer_time=2.254 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 130 Hz
Stats 6464.4: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30541521 bytes_read=4727706 bytes_retransmit=9 bytes_invalid=0 send_seq=575802 receive_seq=575802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=24703 freq=400015894 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40042 bytes_read=125306 bytes_retransmit=0 bytes_invalid=0 send_seq=6645 receive_seq=6645 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999549 adj=49997548 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193174 bytes_read=6145581 bytes_retransmit=9 bytes_invalid=0 send_seq=26899 receive_seq=26899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997699 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135097 bytes_read=3690945 bytes_retransmit=9 bytes_invalid=0 send_seq=18694 receive_seq=18694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997550 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40309 bytes_read=1650444 bytes_retransmit=9 bytes_invalid=0 send_seq=6659 receive_seq=6659 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40795 bytes_read=122860 bytes_retransmit=9 bytes_invalid=0 send_seq=6646 receive_seq=6646 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94887 bytes_read=2527481 bytes_retransmit=0 bytes_invalid=0 send_seq=11205 receive_seq=11205 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998636 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.7 th2: temp=61.1 th3: temp=58.6 sysload=0.18 cputime=491.331 memavail=7393776 print_time=6489.216 buffer_time=2.179 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 131 Hz
Stats 6465.4: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30559252 bytes_read=4729536 bytes_retransmit=9 bytes_invalid=0 send_seq=576106 receive_seq=576106 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=19924 freq=400015892 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40048 bytes_read=125322 bytes_retransmit=0 bytes_invalid=0 send_seq=6646 receive_seq=6646 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999549 adj=49997565 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193180 bytes_read=6145681 bytes_retransmit=9 bytes_invalid=0 send_seq=26900 receive_seq=26900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997783 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135173 bytes_read=3694001 bytes_retransmit=9 bytes_invalid=0 send_seq=18705 receive_seq=18705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997552 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40315 bytes_read=1650678 bytes_retransmit=9 bytes_invalid=0 send_seq=6660 receive_seq=6660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997702 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40801 bytes_read=122876 bytes_retransmit=9 bytes_invalid=0 send_seq=6647 receive_seq=6647 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94893 bytes_read=2527837 bytes_retransmit=0 bytes_invalid=0 send_seq=11206 receive_seq=11206 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998654 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.8 th2: temp=61.3 th3: temp=58.7 sysload=0.16 cputime=491.484 memavail=7395864 print_time=6490.092 buffer_time=2.054 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 132 Hz
Stats 6466.4: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30574756 bytes_read=4731220 bytes_retransmit=9 bytes_invalid=0 send_seq=576375 receive_seq=576375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=23860 freq=400015922 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40054 bytes_read=125338 bytes_retransmit=0 bytes_invalid=0 send_seq=6647 receive_seq=6647 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999548 adj=49997572 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193186 bytes_read=6145823 bytes_retransmit=9 bytes_invalid=0 send_seq=26901 receive_seq=26901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997768 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135249 bytes_read=3697143 bytes_retransmit=9 bytes_invalid=0 send_seq=18716 receive_seq=18716 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000080 adj=63997527 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40321 bytes_read=1650912 bytes_retransmit=9 bytes_invalid=0 send_seq=6661 receive_seq=6661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997689 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40807 bytes_read=122892 bytes_retransmit=9 bytes_invalid=0 send_seq=6648 receive_seq=6648 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94899 bytes_read=2528193 bytes_retransmit=0 bytes_invalid=0 send_seq=11207 receive_seq=11207 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998654 coil_temp=17.0 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.7 th2: temp=61.1 th3: temp=58.6 sysload=0.16 cputime=491.659 memavail=7395864 print_time=6491.284 buffer_time=2.246 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Stats 6467.4: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30590596 bytes_read=4732896 bytes_retransmit=9 bytes_invalid=0 send_seq=576646 receive_seq=576645 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=17331 freq=400015911 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40060 bytes_read=125367 bytes_retransmit=0 bytes_invalid=0 send_seq=6648 receive_seq=6648 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999548 adj=49997519 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193192 bytes_read=6145923 bytes_retransmit=9 bytes_invalid=0 send_seq=26902 receive_seq=26902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997671 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135325 bytes_read=3700200 bytes_retransmit=9 bytes_invalid=0 send_seq=18727 receive_seq=18727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000078 adj=63997713 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40327 bytes_read=1651206 bytes_retransmit=9 bytes_invalid=0 send_seq=6662 receive_seq=6662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40813 bytes_read=122919 bytes_retransmit=9 bytes_invalid=0 send_seq=6649 receive_seq=6649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94905 bytes_read=2528549 bytes_retransmit=0 bytes_invalid=0 send_seq=11208 receive_seq=11208 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998626 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.5 th2: temp=61.2 th3: temp=58.7 sysload=0.16 cputime=491.779 memavail=7393636 print_time=6491.666 buffer_time=1.627 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6468.4: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30608533 bytes_read=4734731 bytes_retransmit=9 bytes_invalid=0 send_seq=576950 receive_seq=576950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=1088 freq=400015905 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40066 bytes_read=125383 bytes_retransmit=0 bytes_invalid=0 send_seq=6649 receive_seq=6649 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999548 adj=49997531 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193198 bytes_read=6146023 bytes_retransmit=9 bytes_invalid=0 send_seq=26903 receive_seq=26903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997757 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135401 bytes_read=3703273 bytes_retransmit=9 bytes_invalid=0 send_seq=18738 receive_seq=18738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000076 adj=63997699 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40333 bytes_read=1651440 bytes_retransmit=9 bytes_invalid=0 send_seq=6663 receive_seq=6663 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40819 bytes_read=122935 bytes_retransmit=9 bytes_invalid=0 send_seq=6650 receive_seq=6650 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94911 bytes_read=2528905 bytes_retransmit=0 bytes_invalid=0 send_seq=11209 receive_seq=11209 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998635 coil_temp=17.0 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.8 th2: temp=61.1 th3: temp=58.8 sysload=0.16 cputime=491.873 memavail=7393636 print_time=6491.666 buffer_time=0.626 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
LIS2DW finished 'toolboard_t1' measurements
Stats 6469.4: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30610010 bytes_read=4735260 bytes_retransmit=9 bytes_invalid=0 send_seq=576988 receive_seq=576988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015918 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40072 bytes_read=125399 bytes_retransmit=0 bytes_invalid=0 send_seq=6650 receive_seq=6650 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999551 adj=49997533 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193204 bytes_read=6146151 bytes_retransmit=9 bytes_invalid=0 send_seq=26904 receive_seq=26904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997754 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135504 bytes_read=3705637 bytes_retransmit=9 bytes_invalid=0 send_seq=18751 receive_seq=18751 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000074 adj=63997688 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40339 bytes_read=1651689 bytes_retransmit=9 bytes_invalid=0 send_seq=6664 receive_seq=6664 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40825 bytes_read=122951 bytes_retransmit=9 bytes_invalid=0 send_seq=6651 receive_seq=6651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94917 bytes_read=2529261 bytes_retransmit=0 bytes_invalid=0 send_seq=11210 receive_seq=11210 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998649 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.8 th2: temp=61.2 th3: temp=58.8 sysload=0.16 cputime=491.967 memavail=7378212 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Resonances data written to /tmp/resonances_y_125.000_250.000_20.000_t1_copy.csv file
Running Command {generate_shaper_graphs}...:
please wait...

Stats 6470.4: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30610308 bytes_read=4735685 bytes_retransmit=9 bytes_invalid=0 send_seq=577011 receive_seq=577011 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015906 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40078 bytes_read=125415 bytes_retransmit=0 bytes_invalid=0 send_seq=6651 receive_seq=6651 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999551 adj=49997564 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193210 bytes_read=6146251 bytes_retransmit=9 bytes_invalid=0 send_seq=26905 receive_seq=26905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997755 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135510 bytes_read=3705737 bytes_retransmit=9 bytes_invalid=0 send_seq=18752 receive_seq=18752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000072 adj=63997639 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40345 bytes_read=1651983 bytes_retransmit=9 bytes_invalid=0 send_seq=6665 receive_seq=6665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40831 bytes_read=122967 bytes_retransmit=9 bytes_invalid=0 send_seq=6652 receive_seq=6652 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94923 bytes_read=2529617 bytes_retransmit=0 bytes_invalid=0 send_seq=11211 receive_seq=11211 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998649 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.7 th2: temp=61.3 th3: temp=58.7 sysload=0.23 cputime=492.069 memavail=7382696 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6471.4: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30610606 bytes_read=4736110 bytes_retransmit=9 bytes_invalid=0 send_seq=577034 receive_seq=577034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015895 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40084 bytes_read=125431 bytes_retransmit=0 bytes_invalid=0 send_seq=6652 receive_seq=6652 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999549 adj=49997573 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193216 bytes_read=6146365 bytes_retransmit=9 bytes_invalid=0 send_seq=26906 receive_seq=26906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997765 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135516 bytes_read=3705837 bytes_retransmit=9 bytes_invalid=0 send_seq=18753 receive_seq=18753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000075 adj=63997634 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40351 bytes_read=1652217 bytes_retransmit=9 bytes_invalid=0 send_seq=6666 receive_seq=6666 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40837 bytes_read=122983 bytes_retransmit=9 bytes_invalid=0 send_seq=6653 receive_seq=6653 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94929 bytes_read=2529973 bytes_retransmit=0 bytes_invalid=0 send_seq=11212 receive_seq=11212 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998663 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.7 th2: temp=61.4 th3: temp=58.7 sysload=0.23 cputime=492.121 memavail=7382196 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 6472.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30610904 bytes_read=4736580 bytes_retransmit=9 bytes_invalid=0 send_seq=577057 receive_seq=577057 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015884 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40090 bytes_read=125460 bytes_retransmit=0 bytes_invalid=0 send_seq=6653 receive_seq=6653 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999549 adj=49997573 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193222 bytes_read=6146493 bytes_retransmit=9 bytes_invalid=0 send_seq=26907 receive_seq=26907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997747 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=135522 bytes_read=3705965 bytes_retransmit=9 bytes_invalid=0 send_seq=18754 receive_seq=18754 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000072 adj=63997684 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40357 bytes_read=1652451 bytes_retransmit=9 bytes_invalid=0 send_seq=6667 receive_seq=6667 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40843 bytes_read=123010 bytes_retransmit=9 bytes_invalid=0 send_seq=6654 receive_seq=6654 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94935 bytes_read=2530329 bytes_retransmit=0 bytes_invalid=0 send_seq=11213 receive_seq=11213 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998672 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=55.7 th1: temp=55.5 th2: temp=61.2 th3: temp=58.8 sysload=0.23 cputime=492.176 memavail=7382200 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6473.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30611202 bytes_read=4737002 bytes_retransmit=9 bytes_invalid=0 send_seq=577080 receive_seq=577080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015873 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40096 bytes_read=125476 bytes_retransmit=0 bytes_invalid=0 send_seq=6654 receive_seq=6654 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999549 adj=49997586 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193228 bytes_read=6146593 bytes_retransmit=9 bytes_invalid=0 send_seq=26908 receive_seq=26908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997738 toolboard_t1: mcu_awake=0.075 mcu_task_avg=0.000100 mcu_task_stddev=0.000074 bytes_write=135528 bytes_read=3706081 bytes_retransmit=9 bytes_invalid=0 send_seq=18755 receive_seq=18755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000072 adj=63997632 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40363 bytes_read=1652745 bytes_retransmit=9 bytes_invalid=0 send_seq=6668 receive_seq=6668 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997745 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40849 bytes_read=123026 bytes_retransmit=9 bytes_invalid=0 send_seq=6655 receive_seq=6655 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94941 bytes_read=2530685 bytes_retransmit=0 bytes_invalid=0 send_seq=11214 receive_seq=11214 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998697 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=55.9 th1: temp=55.5 th2: temp=61.1 th3: temp=58.6 sysload=0.23 cputime=492.230 memavail=7382208 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6474.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30611500 bytes_read=4737425 bytes_retransmit=9 bytes_invalid=0 send_seq=577103 receive_seq=577103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015866 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40102 bytes_read=125492 bytes_retransmit=0 bytes_invalid=0 send_seq=6655 receive_seq=6655 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999549 adj=49997602 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193234 bytes_read=6146693 bytes_retransmit=9 bytes_invalid=0 send_seq=26909 receive_seq=26909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997722 toolboard_t1: mcu_awake=0.075 mcu_task_avg=0.000100 mcu_task_stddev=0.000074 bytes_write=135534 bytes_read=3706181 bytes_retransmit=9 bytes_invalid=0 send_seq=18756 receive_seq=18756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997627 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40369 bytes_read=1652994 bytes_retransmit=9 bytes_invalid=0 send_seq=6669 receive_seq=6669 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997740 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40855 bytes_read=123042 bytes_retransmit=9 bytes_invalid=0 send_seq=6656 receive_seq=6656 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94947 bytes_read=2531041 bytes_retransmit=0 bytes_invalid=0 send_seq=11215 receive_seq=11215 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998699 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.6 th2: temp=61.2 th3: temp=58.7 sysload=0.23 cputime=492.281 memavail=7382208 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6475.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30611798 bytes_read=4737879 bytes_retransmit=9 bytes_invalid=0 send_seq=577126 receive_seq=577126 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015858 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40108 bytes_read=125508 bytes_retransmit=0 bytes_invalid=0 send_seq=6656 receive_seq=6656 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999549 adj=49997605 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193240 bytes_read=6146821 bytes_retransmit=9 bytes_invalid=0 send_seq=26910 receive_seq=26910 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997737 toolboard_t1: mcu_awake=0.075 mcu_task_avg=0.000100 mcu_task_stddev=0.000074 bytes_write=135540 bytes_read=3706309 bytes_retransmit=9 bytes_invalid=0 send_seq=18757 receive_seq=18757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997588 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40375 bytes_read=1653228 bytes_retransmit=9 bytes_invalid=0 send_seq=6670 receive_seq=6670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997721 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40861 bytes_read=123058 bytes_retransmit=9 bytes_invalid=0 send_seq=6657 receive_seq=6657 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94953 bytes_read=2531397 bytes_retransmit=0 bytes_invalid=0 send_seq=11216 receive_seq=11216 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998702 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.4 th2: temp=61.2 th3: temp=58.5 sysload=0.29 cputime=492.333 memavail=7382208 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6476.4: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30612096 bytes_read=4738304 bytes_retransmit=9 bytes_invalid=0 send_seq=577149 receive_seq=577149 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015847 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40114 bytes_read=125524 bytes_retransmit=0 bytes_invalid=0 send_seq=6657 receive_seq=6657 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999549 adj=49997619 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193246 bytes_read=6146935 bytes_retransmit=9 bytes_invalid=0 send_seq=26911 receive_seq=26911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000241 adj=63997884 toolboard_t1: mcu_awake=0.075 mcu_task_avg=0.000100 mcu_task_stddev=0.000074 bytes_write=135546 bytes_read=3706409 bytes_retransmit=9 bytes_invalid=0 send_seq=18758 receive_seq=18758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997564 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40381 bytes_read=1653522 bytes_retransmit=9 bytes_invalid=0 send_seq=6671 receive_seq=6671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997708 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40867 bytes_read=123074 bytes_retransmit=9 bytes_invalid=0 send_seq=6658 receive_seq=6658 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94959 bytes_read=2531753 bytes_retransmit=0 bytes_invalid=0 send_seq=11217 receive_seq=11217 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998691 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=55.7 th1: temp=55.4 th2: temp=61.3 th3: temp=58.7 sysload=0.29 cputime=492.386 memavail=7382216 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6477.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=30612394 bytes_read=4738744 bytes_retransmit=9 bytes_invalid=0 send_seq=577172 receive_seq=577172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015834 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40120 bytes_read=125553 bytes_retransmit=0 bytes_invalid=0 send_seq=6658 receive_seq=6658 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999549 adj=49997624 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193252 bytes_read=6147035 bytes_retransmit=9 bytes_invalid=0 send_seq=26912 receive_seq=26912 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000239 adj=63997979 toolboard_t1: mcu_awake=0.075 mcu_task_avg=0.000100 mcu_task_stddev=0.000074 bytes_write=135552 bytes_read=3706509 bytes_retransmit=9 bytes_invalid=0 send_seq=18759 receive_seq=18759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997549 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40387 bytes_read=1653756 bytes_retransmit=9 bytes_invalid=0 send_seq=6672 receive_seq=6672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997707 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40873 bytes_read=123101 bytes_retransmit=9 bytes_invalid=0 send_seq=6659 receive_seq=6659 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94965 bytes_read=2532109 bytes_retransmit=0 bytes_invalid=0 send_seq=11218 receive_seq=11218 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998688 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=55.6 th1: temp=55.6 th2: temp=61.1 th3: temp=58.6 sysload=0.29 cputime=492.437 memavail=7380972 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6478.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=30612692 bytes_read=4739198 bytes_retransmit=9 bytes_invalid=0 send_seq=577195 receive_seq=577195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015861 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40126 bytes_read=125569 bytes_retransmit=0 bytes_invalid=0 send_seq=6659 receive_seq=6659 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999548 adj=49997626 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193258 bytes_read=6147163 bytes_retransmit=9 bytes_invalid=0 send_seq=26913 receive_seq=26913 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997916 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135558 bytes_read=3706651 bytes_retransmit=9 bytes_invalid=0 send_seq=18760 receive_seq=18760 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997567 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40393 bytes_read=1653990 bytes_retransmit=9 bytes_invalid=0 send_seq=6673 receive_seq=6673 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997703 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40879 bytes_read=123117 bytes_retransmit=9 bytes_invalid=0 send_seq=6660 receive_seq=6660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94971 bytes_read=2532465 bytes_retransmit=0 bytes_invalid=0 send_seq=11219 receive_seq=11219 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998696 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=55.5 th1: temp=55.8 th2: temp=61.4 th3: temp=58.8 sysload=0.29 cputime=492.493 memavail=7367620 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6479.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=30612990 bytes_read=4739623 bytes_retransmit=9 bytes_invalid=0 send_seq=577218 receive_seq=577218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015852 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40132 bytes_read=125585 bytes_retransmit=0 bytes_invalid=0 send_seq=6660 receive_seq=6660 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999549 adj=49997554 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193264 bytes_read=6147263 bytes_retransmit=9 bytes_invalid=0 send_seq=26914 receive_seq=26914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000245 adj=63997763 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135564 bytes_read=3706751 bytes_retransmit=9 bytes_invalid=0 send_seq=18761 receive_seq=18761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997482 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=40399 bytes_read=1654299 bytes_retransmit=9 bytes_invalid=0 send_seq=6674 receive_seq=6674 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997629 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40885 bytes_read=123133 bytes_retransmit=9 bytes_invalid=0 send_seq=6661 receive_seq=6661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94977 bytes_read=2532821 bytes_retransmit=0 bytes_invalid=0 send_seq=11220 receive_seq=11220 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998653 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=55.4 th1: temp=55.5 th2: temp=61.1 th3: temp=58.7 sysload=0.29 cputime=492.552 memavail=7368504 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Fitted shaper 'zv' frequency = 54.0 Hz (vibrations = 1.5%, smoothing ~= 0.059)
To avoid too much smoothing with 'zv', suggested max_accel <= 11400 mm/sec^2
Fitted shaper 'mzv' frequency = 52.8 Hz (vibrations = 0.0%, smoothing ~= 0.073)
To avoid too much smoothing with 'mzv', suggested max_accel <= 8200 mm/sec^2
Fitted shaper 'ei' frequency = 53.2 Hz (vibrations = 0.0%, smoothing ~= 0.114)
To avoid too much smoothing with 'ei', suggested max_accel <= 5300 mm/sec^2
Fitted shaper '2hump_ei' frequency = 71.4 Hz (vibrations = 0.0%, smoothing ~= 0.106)
To avoid too much smoothing with '2hump_ei', suggested max_accel <= 5700 mm/sec^2
Fitted shaper '3hump_ei' frequency = 90.4 Hz (vibrations = 0.0%, smoothing ~= 0.100)
To avoid too much smoothing with '3hump_ei', suggested max_accel <= 6000 mm/sec^2
Recommended shaper is mzv @ 52.8 Hz

Command {generate_shaper_graphs} finished

Running Command {generate_shaper_graphs}...:
please wait...

Stats 6480.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=30613278 bytes_read=4740038 bytes_retransmit=9 bytes_invalid=0 send_seq=577239 receive_seq=577239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015847 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40138 bytes_read=125601 bytes_retransmit=0 bytes_invalid=0 send_seq=6661 receive_seq=6661 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999548 adj=49997582 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193270 bytes_read=6147363 bytes_retransmit=9 bytes_invalid=0 send_seq=26915 receive_seq=26915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000242 adj=63997889 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135570 bytes_read=3706851 bytes_retransmit=9 bytes_invalid=0 send_seq=18762 receive_seq=18762 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997486 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=40405 bytes_read=1654533 bytes_retransmit=9 bytes_invalid=0 send_seq=6675 receive_seq=6675 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40891 bytes_read=123149 bytes_retransmit=9 bytes_invalid=0 send_seq=6662 receive_seq=6662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94983 bytes_read=2533177 bytes_retransmit=0 bytes_invalid=0 send_seq=11221 receive_seq=11221 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998686 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=55.2 th1: temp=55.4 th2: temp=61.3 th3: temp=58.4 sysload=0.59 cputime=492.642 memavail=7382656 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6481.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=30613571 bytes_read=4740487 bytes_retransmit=9 bytes_invalid=0 send_seq=577261 receive_seq=577261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015843 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40144 bytes_read=125617 bytes_retransmit=0 bytes_invalid=0 send_seq=6662 receive_seq=6662 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999549 adj=49997585 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193276 bytes_read=6147505 bytes_retransmit=9 bytes_invalid=0 send_seq=26916 receive_seq=26916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000242 adj=63997812 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135576 bytes_read=3706979 bytes_retransmit=9 bytes_invalid=0 send_seq=18763 receive_seq=18763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000074 adj=63997482 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=40411 bytes_read=1654767 bytes_retransmit=9 bytes_invalid=0 send_seq=6676 receive_seq=6676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40897 bytes_read=123165 bytes_retransmit=9 bytes_invalid=0 send_seq=6663 receive_seq=6663 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94989 bytes_read=2533533 bytes_retransmit=0 bytes_invalid=0 send_seq=11222 receive_seq=11222 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998676 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=55.3 th1: temp=55.3 th2: temp=61.2 th3: temp=58.7 sysload=0.59 cputime=492.696 memavail=7379884 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6482.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30613864 bytes_read=4740922 bytes_retransmit=9 bytes_invalid=0 send_seq=577283 receive_seq=577283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015842 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40150 bytes_read=125646 bytes_retransmit=0 bytes_invalid=0 send_seq=6663 receive_seq=6663 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999548 adj=49997590 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193282 bytes_read=6147605 bytes_retransmit=9 bytes_invalid=0 send_seq=26917 receive_seq=26917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000239 adj=63997797 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135582 bytes_read=3707079 bytes_retransmit=9 bytes_invalid=0 send_seq=18764 receive_seq=18764 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997699 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=40417 bytes_read=1655061 bytes_retransmit=9 bytes_invalid=0 send_seq=6677 receive_seq=6677 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40903 bytes_read=123192 bytes_retransmit=9 bytes_invalid=0 send_seq=6664 receive_seq=6664 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=94995 bytes_read=2533889 bytes_retransmit=0 bytes_invalid=0 send_seq=11223 receive_seq=11223 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998703 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=55.0 th1: temp=55.5 th2: temp=61.2 th3: temp=58.7 sysload=0.59 cputime=492.747 memavail=7379652 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6483.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30614162 bytes_read=4741347 bytes_retransmit=9 bytes_invalid=0 send_seq=577306 receive_seq=577306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015844 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40156 bytes_read=125662 bytes_retransmit=0 bytes_invalid=0 send_seq=6664 receive_seq=6664 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999547 adj=49997575 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193288 bytes_read=6147705 bytes_retransmit=9 bytes_invalid=0 send_seq=26918 receive_seq=26918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000246 adj=63997738 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135588 bytes_read=3707193 bytes_retransmit=9 bytes_invalid=0 send_seq=18765 receive_seq=18765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997626 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=40423 bytes_read=1655295 bytes_retransmit=9 bytes_invalid=0 send_seq=6678 receive_seq=6678 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40909 bytes_read=123208 bytes_retransmit=9 bytes_invalid=0 send_seq=6665 receive_seq=6665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95001 bytes_read=2534245 bytes_retransmit=0 bytes_invalid=0 send_seq=11224 receive_seq=11224 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998717 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=55.0 th1: temp=55.2 th2: temp=61.0 th3: temp=58.7 sysload=0.59 cputime=492.799 memavail=7379652 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6484.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30614460 bytes_read=4741797 bytes_retransmit=9 bytes_invalid=0 send_seq=577329 receive_seq=577329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015853 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40162 bytes_read=125678 bytes_retransmit=0 bytes_invalid=0 send_seq=6665 receive_seq=6665 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999547 adj=49997551 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193294 bytes_read=6147833 bytes_retransmit=9 bytes_invalid=0 send_seq=26919 receive_seq=26919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000243 adj=63997829 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135594 bytes_read=3707321 bytes_retransmit=9 bytes_invalid=0 send_seq=18766 receive_seq=18766 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997581 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40429 bytes_read=1655544 bytes_retransmit=9 bytes_invalid=0 send_seq=6679 receive_seq=6679 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40915 bytes_read=123224 bytes_retransmit=9 bytes_invalid=0 send_seq=6666 receive_seq=6666 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999492 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95007 bytes_read=2534601 bytes_retransmit=0 bytes_invalid=0 send_seq=11225 receive_seq=11225 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998698 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=54.8 th1: temp=55.3 th2: temp=61.1 th3: temp=58.7 sysload=0.59 cputime=492.852 memavail=7379652 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6485.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30614758 bytes_read=4742222 bytes_retransmit=9 bytes_invalid=0 send_seq=577352 receive_seq=577352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015857 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40168 bytes_read=125694 bytes_retransmit=0 bytes_invalid=0 send_seq=6666 receive_seq=6666 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999546 adj=49997538 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193300 bytes_read=6147933 bytes_retransmit=9 bytes_invalid=0 send_seq=26920 receive_seq=26920 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000250 adj=63997728 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135600 bytes_read=3707421 bytes_retransmit=9 bytes_invalid=0 send_seq=18767 receive_seq=18767 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997526 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40435 bytes_read=1655838 bytes_retransmit=9 bytes_invalid=0 send_seq=6680 receive_seq=6680 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997618 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40921 bytes_read=123240 bytes_retransmit=9 bytes_invalid=0 send_seq=6667 receive_seq=6667 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999471 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95013 bytes_read=2534957 bytes_retransmit=0 bytes_invalid=0 send_seq=11226 receive_seq=11226 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998680 coil_temp=17.0 refs=0 mcu_temp=20.34 supply_voltage=3.011 th0: temp=54.8 th1: temp=55.3 th2: temp=61.2 th3: temp=58.6 sysload=0.62 cputime=492.904 memavail=7379652 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6486.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30615056 bytes_read=4742661 bytes_retransmit=9 bytes_invalid=0 send_seq=577375 receive_seq=577375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015852 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40174 bytes_read=125710 bytes_retransmit=0 bytes_invalid=0 send_seq=6667 receive_seq=6667 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999545 adj=49997532 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=193306 bytes_read=6148040 bytes_retransmit=9 bytes_invalid=0 send_seq=26921 receive_seq=26921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000247 adj=63997821 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135606 bytes_read=3707514 bytes_retransmit=9 bytes_invalid=0 send_seq=18768 receive_seq=18768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997501 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40441 bytes_read=1656072 bytes_retransmit=9 bytes_invalid=0 send_seq=6681 receive_seq=6681 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997615 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40927 bytes_read=123255 bytes_retransmit=9 bytes_invalid=0 send_seq=6668 receive_seq=6668 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95019 bytes_read=2535313 bytes_retransmit=0 bytes_invalid=0 send_seq=11227 receive_seq=11227 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998668 coil_temp=17.0 refs=0 mcu_temp=20.35 supply_voltage=3.011 th0: temp=54.8 th1: temp=55.1 th2: temp=61.3 th3: temp=58.6 sysload=0.62 cputime=492.955 memavail=7379408 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6487.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30615354 bytes_read=4743116 bytes_retransmit=9 bytes_invalid=0 send_seq=577398 receive_seq=577398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015848 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40180 bytes_read=125739 bytes_retransmit=0 bytes_invalid=0 send_seq=6668 receive_seq=6668 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999547 adj=49997530 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=193312 bytes_read=6148157 bytes_retransmit=9 bytes_invalid=0 send_seq=26922 receive_seq=26922 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000244 adj=63997758 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135612 bytes_read=3707631 bytes_retransmit=9 bytes_invalid=0 send_seq=18769 receive_seq=18769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997486 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40447 bytes_read=1656306 bytes_retransmit=9 bytes_invalid=0 send_seq=6682 receive_seq=6682 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997632 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40933 bytes_read=123281 bytes_retransmit=9 bytes_invalid=0 send_seq=6669 receive_seq=6669 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95025 bytes_read=2535669 bytes_retransmit=0 bytes_invalid=0 send_seq=11228 receive_seq=11228 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998664 coil_temp=17.0 refs=0 mcu_temp=20.35 supply_voltage=3.011 th0: temp=54.7 th1: temp=55.2 th2: temp=61.2 th3: temp=58.7 sysload=0.62 cputime=493.009 memavail=7382532 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6488.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30615647 bytes_read=4743536 bytes_retransmit=9 bytes_invalid=0 send_seq=577420 receive_seq=577420 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015872 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40186 bytes_read=125755 bytes_retransmit=0 bytes_invalid=0 send_seq=6669 receive_seq=6669 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999547 adj=49997579 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=193318 bytes_read=6148250 bytes_retransmit=9 bytes_invalid=0 send_seq=26923 receive_seq=26923 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000241 adj=63997707 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=135618 bytes_read=3707738 bytes_retransmit=9 bytes_invalid=0 send_seq=18770 receive_seq=18770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997494 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40453 bytes_read=1656600 bytes_retransmit=9 bytes_invalid=0 send_seq=6683 receive_seq=6683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40939 bytes_read=123296 bytes_retransmit=9 bytes_invalid=0 send_seq=6670 receive_seq=6670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95031 bytes_read=2536025 bytes_retransmit=0 bytes_invalid=0 send_seq=11229 receive_seq=11229 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998659 coil_temp=17.0 refs=0 mcu_temp=20.35 supply_voltage=3.011 th0: temp=54.4 th1: temp=55.2 th2: temp=61.1 th3: temp=58.6 sysload=0.62 cputime=493.063 memavail=7378500 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6489.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30615945 bytes_read=4743975 bytes_retransmit=9 bytes_invalid=0 send_seq=577443 receive_seq=577443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015866 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40192 bytes_read=125771 bytes_retransmit=0 bytes_invalid=0 send_seq=6670 receive_seq=6670 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999546 adj=49997525 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=193324 bytes_read=6148343 bytes_retransmit=9 bytes_invalid=0 send_seq=26924 receive_seq=26924 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000239 adj=63997603 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=135624 bytes_read=3707831 bytes_retransmit=9 bytes_invalid=0 send_seq=18771 receive_seq=18771 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997574 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=40459 bytes_read=1656849 bytes_retransmit=9 bytes_invalid=0 send_seq=6684 receive_seq=6684 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997593 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40945 bytes_read=123311 bytes_retransmit=9 bytes_invalid=0 send_seq=6671 receive_seq=6671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95037 bytes_read=2536381 bytes_retransmit=0 bytes_invalid=0 send_seq=11230 receive_seq=11230 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998627 coil_temp=17.0 refs=0 mcu_temp=20.35 supply_voltage=3.011 th0: temp=54.4 th1: temp=55.1 th2: temp=61.1 th3: temp=58.7 sysload=0.62 cputime=493.122 memavail=7370436 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Fitted shaper 'zv' frequency = 49.4 Hz (vibrations = 24.4%, smoothing ~= 0.069)
To avoid too much smoothing with 'zv', suggested max_accel <= 9500 mm/sec^2
Fitted shaper 'mzv' frequency = 38.0 Hz (vibrations = 7.5%, smoothing ~= 0.141)
To avoid too much smoothing with 'mzv', suggested max_accel <= 4300 mm/sec^2
Fitted shaper 'ei' frequency = 44.4 Hz (vibrations = 5.9%, smoothing ~= 0.163)
To avoid too much smoothing with 'ei', suggested max_accel <= 3700 mm/sec^2
Fitted shaper '2hump_ei' frequency = 41.0 Hz (vibrations = 2.6%, smoothing ~= 0.321)
To avoid too much smoothing with '2hump_ei', suggested max_accel <= 1700 mm/sec^2
Fitted shaper '3hump_ei' frequency = 49.8 Hz (vibrations = 2.5%, smoothing ~= 0.330)
To avoid too much smoothing with '3hump_ei', suggested max_accel <= 1700 mm/sec^2
Recommended shaper is mzv @ 38.0 Hz

Command {generate_shaper_graphs} finished

Running Command {generate_shaper_graphs}...:
please wait...

Stats 6490.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30616238 bytes_read=4744410 bytes_retransmit=9 bytes_invalid=0 send_seq=577465 receive_seq=577465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015864 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40198 bytes_read=125787 bytes_retransmit=0 bytes_invalid=0 send_seq=6671 receive_seq=6671 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999544 adj=49997529 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=193330 bytes_read=6148468 bytes_retransmit=9 bytes_invalid=0 send_seq=26925 receive_seq=26925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997612 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=135630 bytes_read=3707956 bytes_retransmit=9 bytes_invalid=0 send_seq=18772 receive_seq=18772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997541 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=40465 bytes_read=1657083 bytes_retransmit=9 bytes_invalid=0 send_seq=6685 receive_seq=6685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997618 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40951 bytes_read=123326 bytes_retransmit=9 bytes_invalid=0 send_seq=6672 receive_seq=6672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=32.1  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95043 bytes_read=2536737 bytes_retransmit=0 bytes_invalid=0 send_seq=11231 receive_seq=11231 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998634 coil_temp=17.0 refs=0 mcu_temp=20.36 supply_voltage=3.011 th0: temp=54.4 th1: temp=55.2 th2: temp=61.2 th3: temp=58.6 sysload=0.89 cputime=493.235 memavail=7384936 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6491.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30616526 bytes_read=4744825 bytes_retransmit=9 bytes_invalid=0 send_seq=577486 receive_seq=577486 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015862 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40204 bytes_read=125803 bytes_retransmit=0 bytes_invalid=0 send_seq=6672 receive_seq=6672 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999544 adj=49997521 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=193336 bytes_read=6148582 bytes_retransmit=9 bytes_invalid=0 send_seq=26926 receive_seq=26926 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997600 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=135636 bytes_read=3708056 bytes_retransmit=9 bytes_invalid=0 send_seq=18773 receive_seq=18773 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997515 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=40471 bytes_read=1657377 bytes_retransmit=9 bytes_invalid=0 send_seq=6686 receive_seq=6686 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40957 bytes_read=123341 bytes_retransmit=9 bytes_invalid=0 send_seq=6673 receive_seq=6673 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95049 bytes_read=2537093 bytes_retransmit=0 bytes_invalid=0 send_seq=11232 receive_seq=11232 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998658 coil_temp=17.0 refs=0 mcu_temp=20.36 supply_voltage=3.011 th0: temp=54.5 th1: temp=55.1 th2: temp=61.2 th3: temp=58.7 sysload=0.89 cputime=493.293 memavail=7381408 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 6492.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30616824 bytes_read=4745279 bytes_retransmit=9 bytes_invalid=0 send_seq=577509 receive_seq=577509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015862 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40210 bytes_read=125832 bytes_retransmit=0 bytes_invalid=0 send_seq=6673 receive_seq=6673 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999542 adj=49997526 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=193342 bytes_read=6148682 bytes_retransmit=9 bytes_invalid=0 send_seq=26927 receive_seq=26927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997605 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=135642 bytes_read=3708156 bytes_retransmit=9 bytes_invalid=0 send_seq=18774 receive_seq=18774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997527 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=40477 bytes_read=1657611 bytes_retransmit=9 bytes_invalid=0 send_seq=6687 receive_seq=6687 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40963 bytes_read=123367 bytes_retransmit=9 bytes_invalid=0 send_seq=6674 receive_seq=6674 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95055 bytes_read=2537449 bytes_retransmit=0 bytes_invalid=0 send_seq=11233 receive_seq=11233 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998657 coil_temp=17.0 refs=0 mcu_temp=20.36 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.2 th2: temp=61.3 th3: temp=58.7 sysload=0.89 cputime=493.348 memavail=7381156 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6493.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30617122 bytes_read=4745719 bytes_retransmit=9 bytes_invalid=0 send_seq=577532 receive_seq=577532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015858 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40216 bytes_read=125848 bytes_retransmit=0 bytes_invalid=0 send_seq=6674 receive_seq=6674 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999541 adj=49997513 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=193348 bytes_read=6148810 bytes_retransmit=9 bytes_invalid=0 send_seq=26928 receive_seq=26928 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997616 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=135648 bytes_read=3708298 bytes_retransmit=9 bytes_invalid=0 send_seq=18775 receive_seq=18775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997493 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=40483 bytes_read=1657845 bytes_retransmit=9 bytes_invalid=0 send_seq=6688 receive_seq=6688 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40969 bytes_read=123382 bytes_retransmit=9 bytes_invalid=0 send_seq=6675 receive_seq=6675 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95061 bytes_read=2537805 bytes_retransmit=0 bytes_invalid=0 send_seq=11234 receive_seq=11234 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998657 coil_temp=17.0 refs=0 mcu_temp=20.36 supply_voltage=3.011 th0: temp=54.2 th1: temp=54.9 th2: temp=61.1 th3: temp=58.6 sysload=0.89 cputime=493.404 memavail=7381164 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6494.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30617420 bytes_read=4746144 bytes_retransmit=9 bytes_invalid=0 send_seq=577555 receive_seq=577555 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015854 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40222 bytes_read=125864 bytes_retransmit=0 bytes_invalid=0 send_seq=6675 receive_seq=6675 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999541 adj=49997513 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=193354 bytes_read=6148910 bytes_retransmit=9 bytes_invalid=0 send_seq=26929 receive_seq=26929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997612 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=135654 bytes_read=3708398 bytes_retransmit=9 bytes_invalid=0 send_seq=18776 receive_seq=18776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000080 adj=63997474 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40489 bytes_read=1658154 bytes_retransmit=9 bytes_invalid=0 send_seq=6689 receive_seq=6689 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40975 bytes_read=123397 bytes_retransmit=9 bytes_invalid=0 send_seq=6676 receive_seq=6676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95067 bytes_read=2538161 bytes_retransmit=0 bytes_invalid=0 send_seq=11235 receive_seq=11235 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998658 coil_temp=17.0 refs=0 mcu_temp=20.35 supply_voltage=3.011 th0: temp=54.2 th1: temp=55.1 th2: temp=61.2 th3: temp=58.6 sysload=0.89 cputime=493.459 memavail=7381164 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6495.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30617718 bytes_read=4746578 bytes_retransmit=9 bytes_invalid=0 send_seq=577578 receive_seq=577578 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015857 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40228 bytes_read=125880 bytes_retransmit=0 bytes_invalid=0 send_seq=6676 receive_seq=6676 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999539 adj=49997521 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=193360 bytes_read=6149010 bytes_retransmit=9 bytes_invalid=0 send_seq=26930 receive_seq=26930 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997631 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=135660 bytes_read=3708498 bytes_retransmit=9 bytes_invalid=0 send_seq=18777 receive_seq=18777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000077 adj=63997737 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40495 bytes_read=1658388 bytes_retransmit=9 bytes_invalid=0 send_seq=6690 receive_seq=6690 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40981 bytes_read=123412 bytes_retransmit=9 bytes_invalid=0 send_seq=6677 receive_seq=6677 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=31.6  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95073 bytes_read=2538517 bytes_retransmit=0 bytes_invalid=0 send_seq=11236 receive_seq=11236 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998665 coil_temp=17.0 refs=0 mcu_temp=20.35 supply_voltage=3.011 th0: temp=54.2 th1: temp=55.1 th2: temp=61.2 th3: temp=58.7 sysload=0.90 cputime=493.514 memavail=7380912 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6496.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30618016 bytes_read=4747018 bytes_retransmit=9 bytes_invalid=0 send_seq=577601 receive_seq=577601 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015854 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40234 bytes_read=125896 bytes_retransmit=0 bytes_invalid=0 send_seq=6677 receive_seq=6677 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999537 adj=49997502 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=193366 bytes_read=6149152 bytes_retransmit=9 bytes_invalid=0 send_seq=26931 receive_seq=26931 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997634 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=135666 bytes_read=3708626 bytes_retransmit=9 bytes_invalid=0 send_seq=18778 receive_seq=18778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000074 adj=63997639 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40501 bytes_read=1658637 bytes_retransmit=9 bytes_invalid=0 send_seq=6691 receive_seq=6691 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40987 bytes_read=123427 bytes_retransmit=9 bytes_invalid=0 send_seq=6678 receive_seq=6678 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95079 bytes_read=2538873 bytes_retransmit=0 bytes_invalid=0 send_seq=11237 receive_seq=11237 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998654 coil_temp=17.0 refs=0 mcu_temp=20.34 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.0 th2: temp=61.0 th3: temp=58.6 sysload=0.90 cputime=493.573 memavail=7381260 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6497.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30618314 bytes_read=4747458 bytes_retransmit=9 bytes_invalid=0 send_seq=577624 receive_seq=577624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015852 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=40240 bytes_read=125925 bytes_retransmit=0 bytes_invalid=0 send_seq=6678 receive_seq=6678 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999537 adj=49997497 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=193372 bytes_read=6149252 bytes_retransmit=9 bytes_invalid=0 send_seq=26932 receive_seq=26932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997629 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=135672 bytes_read=3708726 bytes_retransmit=9 bytes_invalid=0 send_seq=18779 receive_seq=18779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997576 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40507 bytes_read=1658916 bytes_retransmit=9 bytes_invalid=0 send_seq=6692 receive_seq=6692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40993 bytes_read=123453 bytes_retransmit=9 bytes_invalid=0 send_seq=6679 receive_seq=6679 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95085 bytes_read=2539229 bytes_retransmit=0 bytes_invalid=0 send_seq=11238 receive_seq=11238 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998659 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=54.1 th1: temp=55.0 th2: temp=61.0 th3: temp=58.4 sysload=0.90 cputime=493.628 memavail=7380292 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6498.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30618612 bytes_read=4747897 bytes_retransmit=9 bytes_invalid=0 send_seq=577647 receive_seq=577647 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015845 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=40246 bytes_read=125941 bytes_retransmit=0 bytes_invalid=0 send_seq=6679 receive_seq=6679 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999537 adj=49997510 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=193378 bytes_read=6149352 bytes_retransmit=9 bytes_invalid=0 send_seq=26933 receive_seq=26933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997624 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135678 bytes_read=3708840 bytes_retransmit=9 bytes_invalid=0 send_seq=18780 receive_seq=18780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997530 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40513 bytes_read=1659150 bytes_retransmit=9 bytes_invalid=0 send_seq=6693 receive_seq=6693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=40999 bytes_read=123468 bytes_retransmit=9 bytes_invalid=0 send_seq=6680 receive_seq=6680 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95091 bytes_read=2539585 bytes_retransmit=0 bytes_invalid=0 send_seq=11239 receive_seq=11239 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998684 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=54.1 th1: temp=54.9 th2: temp=61.2 th3: temp=58.5 sysload=0.90 cputime=493.684 memavail=7380292 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6499.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30618910 bytes_read=4748337 bytes_retransmit=9 bytes_invalid=0 send_seq=577670 receive_seq=577670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015847 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=40252 bytes_read=125957 bytes_retransmit=0 bytes_invalid=0 send_seq=6680 receive_seq=6680 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999536 adj=49997528 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=193384 bytes_read=6149480 bytes_retransmit=9 bytes_invalid=0 send_seq=26934 receive_seq=26934 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997632 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135684 bytes_read=3708968 bytes_retransmit=9 bytes_invalid=0 send_seq=18781 receive_seq=18781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997507 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=40519 bytes_read=1659414 bytes_retransmit=9 bytes_invalid=0 send_seq=6694 receive_seq=6694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41005 bytes_read=123483 bytes_retransmit=9 bytes_invalid=0 send_seq=6681 receive_seq=6681 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95097 bytes_read=2539941 bytes_retransmit=0 bytes_invalid=0 send_seq=11240 receive_seq=11240 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998690 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=54.0 th1: temp=55.0 th2: temp=61.3 th3: temp=58.5 sysload=0.90 cputime=493.747 memavail=7368448 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Fitted shaper 'zv' frequency = 52.6 Hz (vibrations = 1.1%, smoothing ~= 0.062)
To avoid too much smoothing with 'zv', suggested max_accel <= 10800 mm/sec^2
Fitted shaper 'mzv' frequency = 54.4 Hz (vibrations = 0.0%, smoothing ~= 0.069)
To avoid too much smoothing with 'mzv', suggested max_accel <= 8700 mm/sec^2
Fitted shaper 'ei' frequency = 65.2 Hz (vibrations = 0.0%, smoothing ~= 0.076)
To avoid too much smoothing with 'ei', suggested max_accel <= 7900 mm/sec^2
Fitted shaper '2hump_ei' frequency = 81.4 Hz (vibrations = 0.0%, smoothing ~= 0.081)
To avoid too much smoothing with '2hump_ei', suggested max_accel <= 7400 mm/sec^2
Fitted shaper '3hump_ei' frequency = 98.0 Hz (vibrations = 0.0%, smoothing ~= 0.085)
To avoid too much smoothing with '3hump_ei', suggested max_accel <= 7000 mm/sec^2
Recommended shaper is zv @ 52.6 Hz

Command {generate_shaper_graphs} finished

Running Command {generate_shaper_graphs}...:
please wait...

Stats 6500.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30619208 bytes_read=4748762 bytes_retransmit=9 bytes_invalid=0 send_seq=577693 receive_seq=577693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015851 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=40258 bytes_read=125973 bytes_retransmit=0 bytes_invalid=0 send_seq=6681 receive_seq=6681 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999535 adj=49997519 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=193390 bytes_read=6149580 bytes_retransmit=9 bytes_invalid=0 send_seq=26935 receive_seq=26935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997621 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135690 bytes_read=3709068 bytes_retransmit=9 bytes_invalid=0 send_seq=18782 receive_seq=18782 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997472 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=40525 bytes_read=1659693 bytes_retransmit=9 bytes_invalid=0 send_seq=6695 receive_seq=6695 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41011 bytes_read=123498 bytes_retransmit=9 bytes_invalid=0 send_seq=6682 receive_seq=6682 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95103 bytes_read=2540297 bytes_retransmit=0 bytes_invalid=0 send_seq=11241 receive_seq=11241 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998678 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.012 th0: temp=54.2 th1: temp=54.8 th2: temp=61.2 th3: temp=58.5 sysload=0.91 cputime=493.852 memavail=7387440 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6501.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30619491 bytes_read=4749186 bytes_retransmit=9 bytes_invalid=0 send_seq=577713 receive_seq=577713 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015855 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=40264 bytes_read=125989 bytes_retransmit=0 bytes_invalid=0 send_seq=6682 receive_seq=6682 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999536 adj=49997512 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193396 bytes_read=6149694 bytes_retransmit=9 bytes_invalid=0 send_seq=26936 receive_seq=26936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997638 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135696 bytes_read=3709168 bytes_retransmit=9 bytes_invalid=0 send_seq=18783 receive_seq=18783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997447 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=40531 bytes_read=1659927 bytes_retransmit=9 bytes_invalid=0 send_seq=6696 receive_seq=6696 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41017 bytes_read=123513 bytes_retransmit=9 bytes_invalid=0 send_seq=6683 receive_seq=6683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95109 bytes_read=2540653 bytes_retransmit=0 bytes_invalid=0 send_seq=11242 receive_seq=11242 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998760 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=54.0 th1: temp=54.8 th2: temp=60.9 th3: temp=58.5 sysload=0.91 cputime=493.912 memavail=7379116 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 6502.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30619789 bytes_read=4749641 bytes_retransmit=9 bytes_invalid=0 send_seq=577736 receive_seq=577736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015872 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40270 bytes_read=126018 bytes_retransmit=0 bytes_invalid=0 send_seq=6683 receive_seq=6683 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999536 adj=49997524 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193402 bytes_read=6149822 bytes_retransmit=9 bytes_invalid=0 send_seq=26937 receive_seq=26937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997670 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135702 bytes_read=3709296 bytes_retransmit=9 bytes_invalid=0 send_seq=18784 receive_seq=18784 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997439 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=40537 bytes_read=1660176 bytes_retransmit=9 bytes_invalid=0 send_seq=6697 receive_seq=6697 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997669 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41023 bytes_read=123539 bytes_retransmit=9 bytes_invalid=0 send_seq=6684 receive_seq=6684 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95115 bytes_read=2541009 bytes_retransmit=0 bytes_invalid=0 send_seq=11243 receive_seq=11243 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998724 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=54.2 th1: temp=54.9 th2: temp=61.2 th3: temp=58.6 sysload=0.91 cputime=493.969 memavail=7378864 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6503.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30620087 bytes_read=4750066 bytes_retransmit=9 bytes_invalid=0 send_seq=577759 receive_seq=577759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015875 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40276 bytes_read=126034 bytes_retransmit=0 bytes_invalid=0 send_seq=6684 receive_seq=6684 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999536 adj=49997497 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193408 bytes_read=6149922 bytes_retransmit=9 bytes_invalid=0 send_seq=26938 receive_seq=26938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997620 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135708 bytes_read=3709410 bytes_retransmit=9 bytes_invalid=0 send_seq=18785 receive_seq=18785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997386 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=40543 bytes_read=1660455 bytes_retransmit=9 bytes_invalid=0 send_seq=6698 receive_seq=6698 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41029 bytes_read=123554 bytes_retransmit=9 bytes_invalid=0 send_seq=6685 receive_seq=6685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95121 bytes_read=2541365 bytes_retransmit=0 bytes_invalid=0 send_seq=11244 receive_seq=11244 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998679 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=54.1 th1: temp=54.9 th2: temp=61.1 th3: temp=58.5 sysload=0.91 cputime=494.025 memavail=7378640 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 6504.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30620385 bytes_read=4750505 bytes_retransmit=9 bytes_invalid=0 send_seq=577782 receive_seq=577782 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015879 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40282 bytes_read=126050 bytes_retransmit=0 bytes_invalid=0 send_seq=6685 receive_seq=6685 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999535 adj=49997506 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193414 bytes_read=6150022 bytes_retransmit=9 bytes_invalid=0 send_seq=26939 receive_seq=26939 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997631 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135714 bytes_read=3709510 bytes_retransmit=9 bytes_invalid=0 send_seq=18786 receive_seq=18786 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997388 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40549 bytes_read=1660704 bytes_retransmit=9 bytes_invalid=0 send_seq=6699 receive_seq=6699 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41035 bytes_read=123569 bytes_retransmit=9 bytes_invalid=0 send_seq=6686 receive_seq=6686 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95127 bytes_read=2541721 bytes_retransmit=0 bytes_invalid=0 send_seq=11245 receive_seq=11245 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998661 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=53.9 th1: temp=54.8 th2: temp=61.1 th3: temp=58.6 sysload=0.91 cputime=494.081 memavail=7378640 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6505.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30620683 bytes_read=4750943 bytes_retransmit=9 bytes_invalid=0 send_seq=577805 receive_seq=577805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015876 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40288 bytes_read=126066 bytes_retransmit=0 bytes_invalid=0 send_seq=6686 receive_seq=6686 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999534 adj=49997500 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193420 bytes_read=6150150 bytes_retransmit=9 bytes_invalid=0 send_seq=26940 receive_seq=26940 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997615 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135720 bytes_read=3709638 bytes_retransmit=9 bytes_invalid=0 send_seq=18787 receive_seq=18787 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997416 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40555 bytes_read=1660953 bytes_retransmit=9 bytes_invalid=0 send_seq=6700 receive_seq=6700 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41041 bytes_read=123584 bytes_retransmit=9 bytes_invalid=0 send_seq=6687 receive_seq=6687 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95133 bytes_read=2542077 bytes_retransmit=0 bytes_invalid=0 send_seq=11246 receive_seq=11246 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998654 coil_temp=17.0 refs=0 mcu_temp=20.34 supply_voltage=3.011 th0: temp=53.7 th1: temp=55.0 th2: temp=61.1 th3: temp=58.4 sysload=0.92 cputime=494.138 memavail=7378640 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6506.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30620981 bytes_read=4751363 bytes_retransmit=9 bytes_invalid=0 send_seq=577828 receive_seq=577828 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015876 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40294 bytes_read=126082 bytes_retransmit=0 bytes_invalid=0 send_seq=6687 receive_seq=6687 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999534 adj=49997506 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193426 bytes_read=6150264 bytes_retransmit=9 bytes_invalid=0 send_seq=26941 receive_seq=26941 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997618 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135726 bytes_read=3709738 bytes_retransmit=9 bytes_invalid=0 send_seq=18788 receive_seq=18788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997422 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40561 bytes_read=1661232 bytes_retransmit=9 bytes_invalid=0 send_seq=6701 receive_seq=6701 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41047 bytes_read=123599 bytes_retransmit=9 bytes_invalid=0 send_seq=6688 receive_seq=6688 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95139 bytes_read=2542433 bytes_retransmit=0 bytes_invalid=0 send_seq=11247 receive_seq=11247 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998671 coil_temp=17.0 refs=0 mcu_temp=20.34 supply_voltage=3.011 th0: temp=53.9 th1: temp=55.2 th2: temp=61.1 th3: temp=58.5 sysload=0.92 cputime=494.194 memavail=7378640 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6507.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30621279 bytes_read=4751832 bytes_retransmit=9 bytes_invalid=0 send_seq=577851 receive_seq=577851 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015875 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40300 bytes_read=126111 bytes_retransmit=0 bytes_invalid=0 send_seq=6688 receive_seq=6688 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999534 adj=49997511 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193432 bytes_read=6150364 bytes_retransmit=9 bytes_invalid=0 send_seq=26942 receive_seq=26942 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997614 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135732 bytes_read=3709838 bytes_retransmit=9 bytes_invalid=0 send_seq=18789 receive_seq=18789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997424 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40567 bytes_read=1661466 bytes_retransmit=9 bytes_invalid=0 send_seq=6702 receive_seq=6702 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997649 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41053 bytes_read=123625 bytes_retransmit=9 bytes_invalid=0 send_seq=6689 receive_seq=6689 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95145 bytes_read=2542789 bytes_retransmit=0 bytes_invalid=0 send_seq=11248 receive_seq=11248 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998692 coil_temp=17.0 refs=0 mcu_temp=20.34 supply_voltage=3.011 th0: temp=53.8 th1: temp=54.9 th2: temp=61.2 th3: temp=58.6 sysload=0.92 cputime=494.251 memavail=7378788 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6508.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30621577 bytes_read=4752257 bytes_retransmit=9 bytes_invalid=0 send_seq=577874 receive_seq=577874 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015873 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40306 bytes_read=126127 bytes_retransmit=0 bytes_invalid=0 send_seq=6689 receive_seq=6689 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999534 adj=49997517 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193438 bytes_read=6150492 bytes_retransmit=9 bytes_invalid=0 send_seq=26943 receive_seq=26943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997626 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135738 bytes_read=3709980 bytes_retransmit=9 bytes_invalid=0 send_seq=18790 receive_seq=18790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40573 bytes_read=1661701 bytes_retransmit=9 bytes_invalid=0 send_seq=6703 receive_seq=6703 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41059 bytes_read=123640 bytes_retransmit=9 bytes_invalid=0 send_seq=6690 receive_seq=6690 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95151 bytes_read=2543145 bytes_retransmit=0 bytes_invalid=0 send_seq=11249 receive_seq=11249 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998694 coil_temp=17.0 refs=0 mcu_temp=20.34 supply_voltage=3.011 th0: temp=53.9 th1: temp=54.9 th2: temp=61.3 th3: temp=58.6 sysload=0.92 cputime=494.307 memavail=7377648 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6509.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30621875 bytes_read=4752682 bytes_retransmit=9 bytes_invalid=0 send_seq=577897 receive_seq=577897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015876 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40312 bytes_read=126143 bytes_retransmit=0 bytes_invalid=0 send_seq=6690 receive_seq=6690 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999534 adj=49997533 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193444 bytes_read=6150592 bytes_retransmit=9 bytes_invalid=0 send_seq=26944 receive_seq=26944 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997646 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135744 bytes_read=3710080 bytes_retransmit=9 bytes_invalid=0 send_seq=18791 receive_seq=18791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40579 bytes_read=1661976 bytes_retransmit=9 bytes_invalid=0 send_seq=6704 receive_seq=6704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41065 bytes_read=123656 bytes_retransmit=9 bytes_invalid=0 send_seq=6691 receive_seq=6691 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95157 bytes_read=2543501 bytes_retransmit=0 bytes_invalid=0 send_seq=11250 receive_seq=11250 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998711 coil_temp=17.0 refs=0 mcu_temp=20.34 supply_voltage=3.011 th0: temp=53.7 th1: temp=54.9 th2: temp=61.1 th3: temp=58.5 sysload=0.92 cputime=494.371 memavail=7366820 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Fitted shaper 'zv' frequency = 55.0 Hz (vibrations = 24.6%, smoothing ~= 0.057)
To avoid too much smoothing with 'zv', suggested max_accel <= 11800 mm/sec^2
Fitted shaper 'mzv' frequency = 39.2 Hz (vibrations = 3.5%, smoothing ~= 0.133)
To avoid too much smoothing with 'mzv', suggested max_accel <= 4500 mm/sec^2
Fitted shaper 'ei' frequency = 48.0 Hz (vibrations = 3.5%, smoothing ~= 0.140)
To avoid too much smoothing with 'ei', suggested max_accel <= 4300 mm/sec^2
Fitted shaper '2hump_ei' frequency = 45.6 Hz (vibrations = 1.9%, smoothing ~= 0.260)
To avoid too much smoothing with '2hump_ei', suggested max_accel <= 2200 mm/sec^2
Fitted shaper '3hump_ei' frequency = 50.4 Hz (vibrations = 1.5%, smoothing ~= 0.323)
To avoid too much smoothing with '3hump_ei', suggested max_accel <= 1700 mm/sec^2
Recommended shaper is mzv @ 39.2 Hz

Command {generate_shaper_graphs} finished

toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 6510.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30622168 bytes_read=4753131 bytes_retransmit=9 bytes_invalid=0 send_seq=577919 receive_seq=577919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015880 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40318 bytes_read=126159 bytes_retransmit=0 bytes_invalid=0 send_seq=6691 receive_seq=6691 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999535 adj=49997535 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193450 bytes_read=6150692 bytes_retransmit=9 bytes_invalid=0 send_seq=26945 receive_seq=26945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997638 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135750 bytes_read=3710180 bytes_retransmit=9 bytes_invalid=0 send_seq=18792 receive_seq=18792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997468 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40585 bytes_read=1662194 bytes_retransmit=9 bytes_invalid=0 send_seq=6705 receive_seq=6705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999584 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41071 bytes_read=123672 bytes_retransmit=9 bytes_invalid=0 send_seq=6692 receive_seq=6692 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95163 bytes_read=2543857 bytes_retransmit=0 bytes_invalid=0 send_seq=11251 receive_seq=11251 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998687 coil_temp=17.0 refs=0 mcu_temp=20.34 supply_voltage=3.011 th0: temp=54.1 th1: temp=54.9 th2: temp=61.2 th3: temp=58.5 sysload=0.84 cputime=494.457 memavail=7391248 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6511.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30622466 bytes_read=4753556 bytes_retransmit=9 bytes_invalid=0 send_seq=577942 receive_seq=577942 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015878 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40324 bytes_read=126175 bytes_retransmit=0 bytes_invalid=0 send_seq=6692 receive_seq=6692 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999534 adj=49997538 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193456 bytes_read=6150834 bytes_retransmit=9 bytes_invalid=0 send_seq=26946 receive_seq=26946 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997639 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135756 bytes_read=3710308 bytes_retransmit=9 bytes_invalid=0 send_seq=18793 receive_seq=18793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997449 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40591 bytes_read=1662426 bytes_retransmit=9 bytes_invalid=0 send_seq=6706 receive_seq=6706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999583 adj=47998056 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41077 bytes_read=123688 bytes_retransmit=9 bytes_invalid=0 send_seq=6693 receive_seq=6693 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95169 bytes_read=2544213 bytes_retransmit=0 bytes_invalid=0 send_seq=11252 receive_seq=11252 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998672 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=53.9 th1: temp=54.7 th2: temp=61.1 th3: temp=58.5 sysload=0.84 cputime=494.502 memavail=7391352 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 6512.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30622759 bytes_read=4753991 bytes_retransmit=9 bytes_invalid=0 send_seq=577964 receive_seq=577964 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015875 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40330 bytes_read=126204 bytes_retransmit=0 bytes_invalid=0 send_seq=6693 receive_seq=6693 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999533 adj=49997530 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193462 bytes_read=6150934 bytes_retransmit=9 bytes_invalid=0 send_seq=26947 receive_seq=26947 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997637 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135762 bytes_read=3710408 bytes_retransmit=9 bytes_invalid=0 send_seq=18794 receive_seq=18794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997472 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40597 bytes_read=1662686 bytes_retransmit=9 bytes_invalid=0 send_seq=6707 receive_seq=6707 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999581 adj=47997936 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41083 bytes_read=123715 bytes_retransmit=9 bytes_invalid=0 send_seq=6694 receive_seq=6694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95175 bytes_read=2544569 bytes_retransmit=0 bytes_invalid=0 send_seq=11253 receive_seq=11253 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998658 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=53.9 th1: temp=54.9 th2: temp=60.9 th3: temp=58.6 sysload=0.84 cputime=494.546 memavail=7391128 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6513.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30623057 bytes_read=4754445 bytes_retransmit=9 bytes_invalid=0 send_seq=577987 receive_seq=577987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015873 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40336 bytes_read=126220 bytes_retransmit=0 bytes_invalid=0 send_seq=6694 receive_seq=6694 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999532 adj=49997531 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193468 bytes_read=6151034 bytes_retransmit=9 bytes_invalid=0 send_seq=26948 receive_seq=26948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997742 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135768 bytes_read=3710522 bytes_retransmit=9 bytes_invalid=0 send_seq=18795 receive_seq=18795 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997493 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40603 bytes_read=1662908 bytes_retransmit=9 bytes_invalid=0 send_seq=6708 receive_seq=6708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999579 adj=47997858 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41089 bytes_read=123731 bytes_retransmit=9 bytes_invalid=0 send_seq=6695 receive_seq=6695 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95181 bytes_read=2544925 bytes_retransmit=0 bytes_invalid=0 send_seq=11254 receive_seq=11254 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998658 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=53.8 th1: temp=54.9 th2: temp=61.0 th3: temp=58.6 sysload=0.84 cputime=494.597 memavail=7395320 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6514.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30623355 bytes_read=4754870 bytes_retransmit=9 bytes_invalid=0 send_seq=578010 receive_seq=578010 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015870 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40342 bytes_read=126236 bytes_retransmit=0 bytes_invalid=0 send_seq=6695 receive_seq=6695 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999532 adj=49997526 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193474 bytes_read=6151162 bytes_retransmit=9 bytes_invalid=0 send_seq=26949 receive_seq=26949 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997714 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135774 bytes_read=3710650 bytes_retransmit=9 bytes_invalid=0 send_seq=18796 receive_seq=18796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997485 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40609 bytes_read=1663187 bytes_retransmit=9 bytes_invalid=0 send_seq=6709 receive_seq=6709 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999582 adj=47997787 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41095 bytes_read=123747 bytes_retransmit=9 bytes_invalid=0 send_seq=6696 receive_seq=6696 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95187 bytes_read=2545281 bytes_retransmit=0 bytes_invalid=0 send_seq=11255 receive_seq=11255 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998741 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=53.9 th1: temp=54.9 th2: temp=61.0 th3: temp=58.4 sysload=0.84 cputime=494.643 memavail=7393928 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6515.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30623654 bytes_read=4755306 bytes_retransmit=9 bytes_invalid=0 send_seq=578033 receive_seq=578033 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015873 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40354 bytes_read=126268 bytes_retransmit=0 bytes_invalid=0 send_seq=6697 receive_seq=6697 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999531 adj=49997535 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193486 bytes_read=6151278 bytes_retransmit=9 bytes_invalid=0 send_seq=26951 receive_seq=26951 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997700 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135786 bytes_read=3710766 bytes_retransmit=9 bytes_invalid=0 send_seq=18798 receive_seq=18798 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997486 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40621 bytes_read=1663467 bytes_retransmit=9 bytes_invalid=0 send_seq=6711 receive_seq=6711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999581 adj=47997800 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41107 bytes_read=123779 bytes_retransmit=9 bytes_invalid=0 send_seq=6698 receive_seq=6698 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95199 bytes_read=2545653 bytes_retransmit=0 bytes_invalid=0 send_seq=11257 receive_seq=11257 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998748 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=53.6 th1: temp=54.8 th2: temp=61.2 th3: temp=58.5 sysload=0.78 cputime=494.688 memavail=7393928 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 6516.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30623952 bytes_read=4755755 bytes_retransmit=9 bytes_invalid=0 send_seq=578056 receive_seq=578056 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015885 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40360 bytes_read=126284 bytes_retransmit=0 bytes_invalid=0 send_seq=6698 receive_seq=6698 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999531 adj=49997524 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193492 bytes_read=6151392 bytes_retransmit=9 bytes_invalid=0 send_seq=26952 receive_seq=26952 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997660 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135792 bytes_read=3710866 bytes_retransmit=9 bytes_invalid=0 send_seq=18799 receive_seq=18799 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997497 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40627 bytes_read=1663701 bytes_retransmit=9 bytes_invalid=0 send_seq=6712 receive_seq=6712 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999579 adj=47997756 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41113 bytes_read=123795 bytes_retransmit=9 bytes_invalid=0 send_seq=6699 receive_seq=6699 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95205 bytes_read=2546009 bytes_retransmit=0 bytes_invalid=0 send_seq=11258 receive_seq=11258 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998698 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=53.8 th1: temp=54.8 th2: temp=61.2 th3: temp=58.6 sysload=0.78 cputime=494.732 memavail=7393932 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6517.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30624250 bytes_read=4756195 bytes_retransmit=9 bytes_invalid=0 send_seq=578079 receive_seq=578079 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015893 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40366 bytes_read=126313 bytes_retransmit=0 bytes_invalid=0 send_seq=6699 receive_seq=6699 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999530 adj=49997505 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193498 bytes_read=6151520 bytes_retransmit=9 bytes_invalid=0 send_seq=26953 receive_seq=26953 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997631 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135798 bytes_read=3710994 bytes_retransmit=9 bytes_invalid=0 send_seq=18800 receive_seq=18800 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997458 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40633 bytes_read=1663965 bytes_retransmit=9 bytes_invalid=0 send_seq=6713 receive_seq=6713 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999578 adj=47997683 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41119 bytes_read=123822 bytes_retransmit=9 bytes_invalid=0 send_seq=6700 receive_seq=6700 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95211 bytes_read=2546365 bytes_retransmit=0 bytes_invalid=0 send_seq=11259 receive_seq=11259 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998660 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=53.6 th1: temp=54.9 th2: temp=60.9 th3: temp=58.5 sysload=0.78 cputime=494.778 memavail=7393440 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6518.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30624548 bytes_read=4756620 bytes_retransmit=9 bytes_invalid=0 send_seq=578102 receive_seq=578102 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015893 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40372 bytes_read=126329 bytes_retransmit=0 bytes_invalid=0 send_seq=6700 receive_seq=6700 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999530 adj=49997487 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193504 bytes_read=6151620 bytes_retransmit=9 bytes_invalid=0 send_seq=26954 receive_seq=26954 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997605 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135804 bytes_read=3711094 bytes_retransmit=9 bytes_invalid=0 send_seq=18801 receive_seq=18801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997436 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40639 bytes_read=1664229 bytes_retransmit=9 bytes_invalid=0 send_seq=6714 receive_seq=6714 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999576 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41125 bytes_read=123838 bytes_retransmit=9 bytes_invalid=0 send_seq=6701 receive_seq=6701 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999443 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95217 bytes_read=2546721 bytes_retransmit=0 bytes_invalid=0 send_seq=11260 receive_seq=11260 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999950 adj=31998651 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.012 th0: temp=53.9 th1: temp=54.8 th2: temp=61.2 th3: temp=58.5 sysload=0.78 cputime=494.821 memavail=7393440 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6519.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30624846 bytes_read=4757074 bytes_retransmit=9 bytes_invalid=0 send_seq=578125 receive_seq=578125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015891 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40378 bytes_read=126345 bytes_retransmit=0 bytes_invalid=0 send_seq=6701 receive_seq=6701 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999528 adj=49997491 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193510 bytes_read=6151720 bytes_retransmit=9 bytes_invalid=0 send_seq=26955 receive_seq=26955 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997613 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135810 bytes_read=3711208 bytes_retransmit=9 bytes_invalid=0 send_seq=18802 receive_seq=18802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997439 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40645 bytes_read=1664478 bytes_retransmit=9 bytes_invalid=0 send_seq=6715 receive_seq=6715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999574 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41131 bytes_read=123854 bytes_retransmit=9 bytes_invalid=0 send_seq=6702 receive_seq=6702 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95223 bytes_read=2547077 bytes_retransmit=0 bytes_invalid=0 send_seq=11261 receive_seq=11261 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999948 adj=31998760 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.7 th1: temp=54.9 th2: temp=61.1 th3: temp=58.4 sysload=0.78 cputime=494.866 memavail=7393440 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 6520.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30625144 bytes_read=4757499 bytes_retransmit=9 bytes_invalid=0 send_seq=578148 receive_seq=578148 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015892 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40384 bytes_read=126361 bytes_retransmit=0 bytes_invalid=0 send_seq=6702 receive_seq=6702 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999526 adj=49997477 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193516 bytes_read=6151848 bytes_retransmit=9 bytes_invalid=0 send_seq=26956 receive_seq=26956 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997635 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135816 bytes_read=3711336 bytes_retransmit=9 bytes_invalid=0 send_seq=18803 receive_seq=18803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997448 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40651 bytes_read=1664742 bytes_retransmit=9 bytes_invalid=0 send_seq=6716 receive_seq=6716 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999576 adj=47997613 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41137 bytes_read=123870 bytes_retransmit=9 bytes_invalid=0 send_seq=6703 receive_seq=6703 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95229 bytes_read=2547433 bytes_retransmit=0 bytes_invalid=0 send_seq=11262 receive_seq=11262 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999947 adj=31998718 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.7 th1: temp=54.8 th2: temp=61.1 th3: temp=58.5 sysload=0.71 cputime=494.910 memavail=7393452 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6521.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30625437 bytes_read=4757919 bytes_retransmit=9 bytes_invalid=0 send_seq=578170 receive_seq=578170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015889 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40390 bytes_read=126377 bytes_retransmit=0 bytes_invalid=0 send_seq=6703 receive_seq=6703 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999528 adj=49997460 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193522 bytes_read=6151948 bytes_retransmit=9 bytes_invalid=0 send_seq=26957 receive_seq=26957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997636 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135822 bytes_read=3711436 bytes_retransmit=9 bytes_invalid=0 send_seq=18804 receive_seq=18804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997450 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40657 bytes_read=1665006 bytes_retransmit=9 bytes_invalid=0 send_seq=6717 receive_seq=6717 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999575 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41143 bytes_read=123886 bytes_retransmit=9 bytes_invalid=0 send_seq=6704 receive_seq=6704 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95235 bytes_read=2547789 bytes_retransmit=0 bytes_invalid=0 send_seq=11263 receive_seq=11263 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999947 adj=31998694 coil_temp=17.0 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=53.6 th1: temp=54.9 th2: temp=61.1 th3: temp=58.4 sysload=0.71 cputime=494.955 memavail=7393452 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6522.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30625715 bytes_read=4758368 bytes_retransmit=9 bytes_invalid=0 send_seq=578189 receive_seq=578189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015888 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40396 bytes_read=126406 bytes_retransmit=0 bytes_invalid=0 send_seq=6704 receive_seq=6704 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999527 adj=49997522 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193528 bytes_read=6152062 bytes_retransmit=9 bytes_invalid=0 send_seq=26958 receive_seq=26958 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997642 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135828 bytes_read=3711536 bytes_retransmit=9 bytes_invalid=0 send_seq=18805 receive_seq=18805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40663 bytes_read=1665240 bytes_retransmit=9 bytes_invalid=0 send_seq=6718 receive_seq=6718 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999573 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41149 bytes_read=123913 bytes_retransmit=9 bytes_invalid=0 send_seq=6705 receive_seq=6705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999468 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95241 bytes_read=2548145 bytes_retransmit=0 bytes_invalid=0 send_seq=11264 receive_seq=11264 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999947 adj=31998682 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.012 th0: temp=53.7 th1: temp=54.8 th2: temp=61.2 th3: temp=58.6 sysload=0.71 cputime=495.000 memavail=7393452 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6523.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30626008 bytes_read=4758788 bytes_retransmit=9 bytes_invalid=0 send_seq=578211 receive_seq=578211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015886 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40402 bytes_read=126422 bytes_retransmit=0 bytes_invalid=0 send_seq=6705 receive_seq=6705 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999526 adj=49997516 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193534 bytes_read=6152190 bytes_retransmit=9 bytes_invalid=0 send_seq=26959 receive_seq=26959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997650 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135834 bytes_read=3711664 bytes_retransmit=9 bytes_invalid=0 send_seq=18806 receive_seq=18806 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997489 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40669 bytes_read=1665504 bytes_retransmit=9 bytes_invalid=0 send_seq=6719 receive_seq=6719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999572 adj=47997629 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41155 bytes_read=123929 bytes_retransmit=9 bytes_invalid=0 send_seq=6706 receive_seq=6706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999468 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95247 bytes_read=2548501 bytes_retransmit=0 bytes_invalid=0 send_seq=11265 receive_seq=11265 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999947 adj=31998683 coil_temp=17.0 refs=0 mcu_temp=20.32 supply_voltage=3.012 th0: temp=53.4 th1: temp=54.8 th2: temp=61.1 th3: temp=58.5 sysload=0.71 cputime=495.045 memavail=7393452 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6524.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30626306 bytes_read=4759213 bytes_retransmit=9 bytes_invalid=0 send_seq=578234 receive_seq=578234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015885 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40408 bytes_read=126438 bytes_retransmit=0 bytes_invalid=0 send_seq=6706 receive_seq=6706 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999525 adj=49997513 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193540 bytes_read=6152290 bytes_retransmit=9 bytes_invalid=0 send_seq=26960 receive_seq=26960 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997649 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135840 bytes_read=3711778 bytes_retransmit=9 bytes_invalid=0 send_seq=18807 receive_seq=18807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40675 bytes_read=1665783 bytes_retransmit=9 bytes_invalid=0 send_seq=6720 receive_seq=6720 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999571 adj=47997623 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41161 bytes_read=123945 bytes_retransmit=9 bytes_invalid=0 send_seq=6707 receive_seq=6707 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999462 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95253 bytes_read=2548857 bytes_retransmit=0 bytes_invalid=0 send_seq=11266 receive_seq=11266 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998690 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=53.6 th1: temp=54.7 th2: temp=61.3 th3: temp=58.5 sysload=0.71 cputime=495.089 memavail=7393452 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 6525.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30626589 bytes_read=4759652 bytes_retransmit=9 bytes_invalid=0 send_seq=578254 receive_seq=578254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015885 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40414 bytes_read=126454 bytes_retransmit=0 bytes_invalid=0 send_seq=6707 receive_seq=6707 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999525 adj=49997505 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193546 bytes_read=6152390 bytes_retransmit=9 bytes_invalid=0 send_seq=26961 receive_seq=26961 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997643 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135846 bytes_read=3711878 bytes_retransmit=9 bytes_invalid=0 send_seq=18808 receive_seq=18808 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40681 bytes_read=1666017 bytes_retransmit=9 bytes_invalid=0 send_seq=6721 receive_seq=6721 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999570 adj=47997615 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41167 bytes_read=123961 bytes_retransmit=9 bytes_invalid=0 send_seq=6708 receive_seq=6708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95259 bytes_read=2549213 bytes_retransmit=0 bytes_invalid=0 send_seq=11267 receive_seq=11267 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998668 coil_temp=17.0 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=53.5 th1: temp=54.9 th2: temp=61.1 th3: temp=58.4 sysload=0.66 cputime=495.141 memavail=7392472 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6526.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30626887 bytes_read=4760077 bytes_retransmit=9 bytes_invalid=0 send_seq=578277 receive_seq=578277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015885 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40420 bytes_read=126470 bytes_retransmit=0 bytes_invalid=0 send_seq=6708 receive_seq=6708 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999524 adj=49997505 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193552 bytes_read=6152518 bytes_retransmit=9 bytes_invalid=0 send_seq=26962 receive_seq=26962 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997651 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135852 bytes_read=3712006 bytes_retransmit=9 bytes_invalid=0 send_seq=18809 receive_seq=18809 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997517 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40687 bytes_read=1666281 bytes_retransmit=9 bytes_invalid=0 send_seq=6722 receive_seq=6722 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999569 adj=47997606 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41173 bytes_read=123977 bytes_retransmit=9 bytes_invalid=0 send_seq=6709 receive_seq=6709 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95265 bytes_read=2549569 bytes_retransmit=0 bytes_invalid=0 send_seq=11268 receive_seq=11268 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998657 coil_temp=17.0 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=53.6 th1: temp=54.7 th2: temp=61.1 th3: temp=58.5 sysload=0.66 cputime=495.185 memavail=7392472 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6527.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30627185 bytes_read=4760512 bytes_retransmit=9 bytes_invalid=0 send_seq=578300 receive_seq=578300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015884 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40426 bytes_read=126499 bytes_retransmit=0 bytes_invalid=0 send_seq=6709 receive_seq=6709 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999522 adj=49997500 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193558 bytes_read=6152632 bytes_retransmit=9 bytes_invalid=0 send_seq=26963 receive_seq=26963 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997652 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135858 bytes_read=3712106 bytes_retransmit=9 bytes_invalid=0 send_seq=18810 receive_seq=18810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997507 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40693 bytes_read=1666545 bytes_retransmit=9 bytes_invalid=0 send_seq=6723 receive_seq=6723 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999568 adj=47997618 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41179 bytes_read=124004 bytes_retransmit=9 bytes_invalid=0 send_seq=6710 receive_seq=6710 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95271 bytes_read=2549925 bytes_retransmit=0 bytes_invalid=0 send_seq=11269 receive_seq=11269 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998648 coil_temp=17.0 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=53.7 th1: temp=54.8 th2: temp=61.0 th3: temp=58.4 sysload=0.66 cputime=495.231 memavail=7392236 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 6528.4: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30627483 bytes_read=4760966 bytes_retransmit=9 bytes_invalid=0 send_seq=578323 receive_seq=578323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015885 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40432 bytes_read=126515 bytes_retransmit=0 bytes_invalid=0 send_seq=6710 receive_seq=6710 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999521 adj=49997488 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193564 bytes_read=6152732 bytes_retransmit=9 bytes_invalid=0 send_seq=26964 receive_seq=26964 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997691 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135864 bytes_read=3712206 bytes_retransmit=9 bytes_invalid=0 send_seq=18811 receive_seq=18811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40699 bytes_read=1666779 bytes_retransmit=9 bytes_invalid=0 send_seq=6724 receive_seq=6724 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999567 adj=47997610 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41185 bytes_read=124020 bytes_retransmit=9 bytes_invalid=0 send_seq=6711 receive_seq=6711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95277 bytes_read=2550281 bytes_retransmit=0 bytes_invalid=0 send_seq=11270 receive_seq=11270 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998635 coil_temp=17.0 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=53.6 th1: temp=54.7 th2: temp=61.1 th3: temp=58.5 sysload=0.66 cputime=495.275 memavail=7392360 print_time=6491.666 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Extruder extruder already active
Extruder 'extruder' now syncing with 'extruder'
Extruder 'extruder1' now syncing with 'extruder'
shaper_type_x:mzv shaper_freq_x:0.000 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:0.000 damping_ratio_y:0.100000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 6544.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30634157 bytes_read=4768021 bytes_retransmit=9 bytes_invalid=0 send_seq=578705 receive_seq=578705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015925 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=40528 bytes_read=126805 bytes_retransmit=0 bytes_invalid=0 send_seq=6726 receive_seq=6726 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999513 adj=49997474 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193660 bytes_read=6154542 bytes_retransmit=9 bytes_invalid=0 send_seq=26980 receive_seq=26980 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000241 adj=63997842 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135960 bytes_read=3714030 bytes_retransmit=9 bytes_invalid=0 send_seq=18827 receive_seq=18827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997462 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40795 bytes_read=1670943 bytes_retransmit=9 bytes_invalid=0 send_seq=6740 receive_seq=6740 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997598 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41281 bytes_read=124309 bytes_retransmit=9 bytes_invalid=0 send_seq=6727 receive_seq=6727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95373 bytes_read=2555902 bytes_retransmit=0 bytes_invalid=0 send_seq=11286 receive_seq=11286 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998630 coil_temp=17.0 refs=0 mcu_temp=20.41 supply_voltage=3.011 th0: temp=53.7 th1: temp=54.6 th2: temp=61.1 th3: temp=58.4 sysload=0.51 cputime=496.056 memavail=7395288 print_time=6567.355 buffer_time=0.235 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6545.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30634450 bytes_read=4768441 bytes_retransmit=9 bytes_invalid=0 send_seq=578727 receive_seq=578727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015927 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=40534 bytes_read=126821 bytes_retransmit=0 bytes_invalid=0 send_seq=6727 receive_seq=6727 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999513 adj=49997453 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193666 bytes_read=6154642 bytes_retransmit=9 bytes_invalid=0 send_seq=26981 receive_seq=26981 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000239 adj=63997707 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135966 bytes_read=3714130 bytes_retransmit=9 bytes_invalid=0 send_seq=18828 receive_seq=18828 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997415 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40801 bytes_read=1671177 bytes_retransmit=9 bytes_invalid=0 send_seq=6741 receive_seq=6741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997575 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41287 bytes_read=124325 bytes_retransmit=9 bytes_invalid=0 send_seq=6728 receive_seq=6728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95379 bytes_read=2556258 bytes_retransmit=0 bytes_invalid=0 send_seq=11287 receive_seq=11287 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998606 coil_temp=17.0 refs=0 mcu_temp=20.41 supply_voltage=3.011 th0: temp=53.7 th1: temp=54.7 th2: temp=61.1 th3: temp=58.4 sysload=0.47 cputime=496.102 memavail=7395296 print_time=6567.355 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6546.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30634748 bytes_read=4768895 bytes_retransmit=9 bytes_invalid=0 send_seq=578750 receive_seq=578750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015924 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=40540 bytes_read=126837 bytes_retransmit=0 bytes_invalid=0 send_seq=6728 receive_seq=6728 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999514 adj=49997466 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193672 bytes_read=6154756 bytes_retransmit=9 bytes_invalid=0 send_seq=26982 receive_seq=26982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997669 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135972 bytes_read=3714244 bytes_retransmit=9 bytes_invalid=0 send_seq=18829 receive_seq=18829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997425 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40807 bytes_read=1671411 bytes_retransmit=9 bytes_invalid=0 send_seq=6742 receive_seq=6742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997579 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41293 bytes_read=124341 bytes_retransmit=9 bytes_invalid=0 send_seq=6729 receive_seq=6729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999426 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95385 bytes_read=2556614 bytes_retransmit=0 bytes_invalid=0 send_seq=11288 receive_seq=11288 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998601 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.011 th0: temp=53.7 th1: temp=54.4 th2: temp=61.3 th3: temp=58.6 sysload=0.47 cputime=496.147 memavail=7395296 print_time=6567.355 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6547.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30635046 bytes_read=4769335 bytes_retransmit=9 bytes_invalid=0 send_seq=578773 receive_seq=578773 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015921 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40546 bytes_read=126866 bytes_retransmit=0 bytes_invalid=0 send_seq=6729 receive_seq=6729 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999516 adj=49997499 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193678 bytes_read=6154884 bytes_retransmit=9 bytes_invalid=0 send_seq=26983 receive_seq=26983 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997652 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135978 bytes_read=3714358 bytes_retransmit=9 bytes_invalid=0 send_seq=18830 receive_seq=18830 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997464 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40813 bytes_read=1671705 bytes_retransmit=9 bytes_invalid=0 send_seq=6743 receive_seq=6743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997597 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41299 bytes_read=124368 bytes_retransmit=9 bytes_invalid=0 send_seq=6730 receive_seq=6730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95391 bytes_read=2556970 bytes_retransmit=0 bytes_invalid=0 send_seq=11289 receive_seq=11289 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998608 coil_temp=17.0 refs=0 mcu_temp=20.39 supply_voltage=3.011 th0: temp=53.4 th1: temp=54.8 th2: temp=61.0 th3: temp=58.3 sysload=0.47 cputime=496.194 memavail=7388764 print_time=6567.355 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6548.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30635344 bytes_read=4769758 bytes_retransmit=9 bytes_invalid=0 send_seq=578796 receive_seq=578796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015925 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40552 bytes_read=126882 bytes_retransmit=0 bytes_invalid=0 send_seq=6730 receive_seq=6730 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999514 adj=49997539 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193684 bytes_read=6154984 bytes_retransmit=9 bytes_invalid=0 send_seq=26984 receive_seq=26984 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997643 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135984 bytes_read=3714458 bytes_retransmit=9 bytes_invalid=0 send_seq=18831 receive_seq=18831 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997478 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40819 bytes_read=1671939 bytes_retransmit=9 bytes_invalid=0 send_seq=6744 receive_seq=6744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997610 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41305 bytes_read=124384 bytes_retransmit=9 bytes_invalid=0 send_seq=6731 receive_seq=6731 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95397 bytes_read=2557326 bytes_retransmit=0 bytes_invalid=0 send_seq=11290 receive_seq=11290 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998628 coil_temp=17.0 refs=0 mcu_temp=20.38 supply_voltage=3.011 th0: temp=53.6 th1: temp=54.7 th2: temp=61.2 th3: temp=58.4 sysload=0.47 cputime=496.239 memavail=7394652 print_time=6567.355 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6549.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30635637 bytes_read=4770202 bytes_retransmit=9 bytes_invalid=0 send_seq=578818 receive_seq=578818 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015922 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40558 bytes_read=126898 bytes_retransmit=0 bytes_invalid=0 send_seq=6731 receive_seq=6731 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999513 adj=49997503 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193690 bytes_read=6155112 bytes_retransmit=9 bytes_invalid=0 send_seq=26985 receive_seq=26985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000239 adj=63997714 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135990 bytes_read=3714586 bytes_retransmit=9 bytes_invalid=0 send_seq=18832 receive_seq=18832 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997471 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40825 bytes_read=1672188 bytes_retransmit=9 bytes_invalid=0 send_seq=6745 receive_seq=6745 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41311 bytes_read=124400 bytes_retransmit=9 bytes_invalid=0 send_seq=6732 receive_seq=6732 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95403 bytes_read=2557682 bytes_retransmit=0 bytes_invalid=0 send_seq=11291 receive_seq=11291 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998625 coil_temp=17.0 refs=0 mcu_temp=20.39 supply_voltage=3.011 th0: temp=53.9 th1: temp=54.7 th2: temp=61.3 th3: temp=58.5 sysload=0.47 cputime=496.283 memavail=7394652 print_time=6567.355 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6550.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30635930 bytes_read=4770622 bytes_retransmit=9 bytes_invalid=0 send_seq=578840 receive_seq=578840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015923 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40564 bytes_read=126914 bytes_retransmit=0 bytes_invalid=0 send_seq=6732 receive_seq=6732 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999511 adj=49997494 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193696 bytes_read=6155212 bytes_retransmit=9 bytes_invalid=0 send_seq=26986 receive_seq=26986 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000246 adj=63997701 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=135996 bytes_read=3714700 bytes_retransmit=9 bytes_invalid=0 send_seq=18833 receive_seq=18833 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997484 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40831 bytes_read=1672482 bytes_retransmit=9 bytes_invalid=0 send_seq=6746 receive_seq=6746 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41317 bytes_read=124416 bytes_retransmit=9 bytes_invalid=0 send_seq=6733 receive_seq=6733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95409 bytes_read=2558038 bytes_retransmit=0 bytes_invalid=0 send_seq=11292 receive_seq=11292 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998635 coil_temp=17.0 refs=0 mcu_temp=20.38 supply_voltage=3.011 th0: temp=53.5 th1: temp=54.7 th2: temp=61.3 th3: temp=58.4 sysload=0.43 cputime=496.326 memavail=7394652 print_time=6567.355 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6551.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30636228 bytes_read=4771047 bytes_retransmit=9 bytes_invalid=0 send_seq=578863 receive_seq=578863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015931 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40570 bytes_read=126930 bytes_retransmit=0 bytes_invalid=0 send_seq=6733 receive_seq=6733 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999510 adj=49997474 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193702 bytes_read=6155312 bytes_retransmit=9 bytes_invalid=0 send_seq=26987 receive_seq=26987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000245 adj=63997816 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136002 bytes_read=3714800 bytes_retransmit=9 bytes_invalid=0 send_seq=18834 receive_seq=18834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997494 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40837 bytes_read=1672716 bytes_retransmit=9 bytes_invalid=0 send_seq=6747 receive_seq=6747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41323 bytes_read=124432 bytes_retransmit=9 bytes_invalid=0 send_seq=6734 receive_seq=6734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95415 bytes_read=2558394 bytes_retransmit=0 bytes_invalid=0 send_seq=11293 receive_seq=11293 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998648 coil_temp=17.0 refs=0 mcu_temp=20.38 supply_voltage=3.011 th0: temp=53.6 th1: temp=54.6 th2: temp=61.0 th3: temp=58.5 sysload=0.43 cputime=496.370 memavail=7394652 print_time=6567.355 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6552.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30636521 bytes_read=4771511 bytes_retransmit=9 bytes_invalid=0 send_seq=578885 receive_seq=578885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015924 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40576 bytes_read=126959 bytes_retransmit=0 bytes_invalid=0 send_seq=6734 receive_seq=6734 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999509 adj=49997452 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193708 bytes_read=6155454 bytes_retransmit=9 bytes_invalid=0 send_seq=26988 receive_seq=26988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000245 adj=63997748 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136008 bytes_read=3714914 bytes_retransmit=9 bytes_invalid=0 send_seq=18835 receive_seq=18835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997475 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40843 bytes_read=1672950 bytes_retransmit=9 bytes_invalid=0 send_seq=6748 receive_seq=6748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41329 bytes_read=124459 bytes_retransmit=9 bytes_invalid=0 send_seq=6735 receive_seq=6735 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95421 bytes_read=2558750 bytes_retransmit=0 bytes_invalid=0 send_seq=11294 receive_seq=11294 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998636 coil_temp=17.0 refs=0 mcu_temp=20.37 supply_voltage=3.011 th0: temp=53.4 th1: temp=54.8 th2: temp=61.0 th3: temp=58.4 sysload=0.43 cputime=496.415 memavail=7394652 print_time=6567.355 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
RatOS:: All requested axes already homed. Skipping homing.
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Probing point (125.000, 250.000, 20.000)
Stats 6553.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30637584 bytes_read=4772001 bytes_retransmit=9 bytes_invalid=0 send_seq=578921 receive_seq=578921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015953 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40582 bytes_read=126975 bytes_retransmit=0 bytes_invalid=0 send_seq=6735 receive_seq=6735 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999509 adj=49997470 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193714 bytes_read=6155547 bytes_retransmit=9 bytes_invalid=0 send_seq=26989 receive_seq=26989 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000243 adj=63997754 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136014 bytes_read=3715021 bytes_retransmit=9 bytes_invalid=0 send_seq=18836 receive_seq=18836 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997499 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40849 bytes_read=1673244 bytes_retransmit=9 bytes_invalid=0 send_seq=6749 receive_seq=6749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41335 bytes_read=124475 bytes_retransmit=9 bytes_invalid=0 send_seq=6736 receive_seq=6736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95427 bytes_read=2559106 bytes_retransmit=0 bytes_invalid=0 send_seq=11295 receive_seq=11295 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998640 coil_temp=17.0 refs=0 mcu_temp=20.38 supply_voltage=3.011 th0: temp=53.7 th1: temp=54.6 th2: temp=60.8 th3: temp=58.5 sysload=0.43 cputime=496.508 memavail=7394652 print_time=6576.366 buffer_time=0.243 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t0' measurements
toolhead: max_velocity: 600.000000
max_accel: 8379.841000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance testing
Testing frequency 10 Hz
Testing frequency 11 Hz
Testing frequency 12 Hz
Stats 6554.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30642587 bytes_read=4772811 bytes_retransmit=9 bytes_invalid=0 send_seq=579021 receive_seq=579021 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015962 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40588 bytes_read=126991 bytes_retransmit=0 bytes_invalid=0 send_seq=6736 receive_seq=6736 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999509 adj=49997420 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193864 bytes_read=6157705 bytes_retransmit=9 bytes_invalid=0 send_seq=27006 receive_seq=27006 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000263 adj=63997631 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136020 bytes_read=3715127 bytes_retransmit=9 bytes_invalid=0 send_seq=18837 receive_seq=18837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997427 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40855 bytes_read=1673493 bytes_retransmit=9 bytes_invalid=0 send_seq=6750 receive_seq=6750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997592 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41341 bytes_read=124491 bytes_retransmit=9 bytes_invalid=0 send_seq=6737 receive_seq=6737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999422 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95433 bytes_read=2559462 bytes_retransmit=0 bytes_invalid=0 send_seq=11296 receive_seq=11296 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998608 coil_temp=17.0 refs=0 mcu_temp=20.37 supply_voltage=3.011 th0: temp=53.7 th1: temp=54.5 th2: temp=61.1 th3: temp=58.5 sysload=0.43 cputime=496.687 memavail=7394652 print_time=6579.584 buffer_time=2.460 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6555.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30644156 bytes_read=4773360 bytes_retransmit=9 bytes_invalid=0 send_seq=579063 receive_seq=579063 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015962 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40594 bytes_read=127007 bytes_retransmit=0 bytes_invalid=0 send_seq=6737 receive_seq=6737 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999507 adj=49997496 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=193940 bytes_read=6160715 bytes_retransmit=9 bytes_invalid=0 send_seq=27017 receive_seq=27017 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000263 adj=63997886 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136026 bytes_read=3715233 bytes_retransmit=9 bytes_invalid=0 send_seq=18838 receive_seq=18838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997483 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40861 bytes_read=1673727 bytes_retransmit=9 bytes_invalid=0 send_seq=6751 receive_seq=6751 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41347 bytes_read=124507 bytes_retransmit=9 bytes_invalid=0 send_seq=6738 receive_seq=6738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95439 bytes_read=2559818 bytes_retransmit=0 bytes_invalid=0 send_seq=11297 receive_seq=11297 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998657 coil_temp=17.0 refs=0 mcu_temp=20.37 supply_voltage=3.011 th0: temp=53.7 th1: temp=54.6 th2: temp=61.1 th3: temp=58.5 sysload=0.40 cputime=496.757 memavail=7394428 print_time=6580.177 buffer_time=2.053 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 13 Hz
Testing frequency 14 Hz
Stats 6556.5: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=30647095 bytes_read=4773995 bytes_retransmit=9 bytes_invalid=0 send_seq=579128 receive_seq=579128 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=0 freq=400015973 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40600 bytes_read=127023 bytes_retransmit=0 bytes_invalid=0 send_seq=6738 receive_seq=6738 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999506 adj=49997471 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=194016 bytes_read=6163736 bytes_retransmit=9 bytes_invalid=0 send_seq=27028 receive_seq=27028 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000259 adj=63997890 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136032 bytes_read=3715339 bytes_retransmit=9 bytes_invalid=0 send_seq=18839 receive_seq=18839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40867 bytes_read=1674021 bytes_retransmit=9 bytes_invalid=0 send_seq=6752 receive_seq=6752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997614 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41353 bytes_read=124523 bytes_retransmit=9 bytes_invalid=0 send_seq=6739 receive_seq=6739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95445 bytes_read=2560174 bytes_retransmit=0 bytes_invalid=0 send_seq=11298 receive_seq=11298 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998649 coil_temp=17.0 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=53.8 th1: temp=54.8 th2: temp=61.1 th3: temp=58.6 sysload=0.40 cputime=496.838 memavail=7394428 print_time=6581.429 buffer_time=2.305 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 15 Hz
Stats 6557.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30649214 bytes_read=4774575 bytes_retransmit=9 bytes_invalid=0 send_seq=579179 receive_seq=579179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400015987 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40606 bytes_read=127052 bytes_retransmit=0 bytes_invalid=0 send_seq=6739 receive_seq=6739 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999505 adj=49997455 toolboard_t0: mcu_awake=0.204 mcu_task_avg=0.000114 mcu_task_stddev=0.000070 bytes_write=194092 bytes_read=6166803 bytes_retransmit=9 bytes_invalid=0 send_seq=27039 receive_seq=27039 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000256 adj=63997778 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136038 bytes_read=3715436 bytes_retransmit=9 bytes_invalid=0 send_seq=18840 receive_seq=18840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997463 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40873 bytes_read=1674255 bytes_retransmit=9 bytes_invalid=0 send_seq=6753 receive_seq=6753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997598 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41359 bytes_read=124550 bytes_retransmit=9 bytes_invalid=0 send_seq=6740 receive_seq=6740 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95451 bytes_read=2560530 bytes_retransmit=0 bytes_invalid=0 send_seq=11299 receive_seq=11299 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998641 coil_temp=17.0 refs=0 mcu_temp=20.36 supply_voltage=3.012 th0: temp=53.9 th1: temp=54.8 th2: temp=61.0 th3: temp=58.6 sysload=0.40 cputime=496.914 memavail=7393168 print_time=6582.300 buffer_time=2.176 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 16 Hz
Stats 6558.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30651940 bytes_read=4775219 bytes_retransmit=9 bytes_invalid=0 send_seq=579240 receive_seq=579240 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=0 freq=400015982 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40612 bytes_read=127068 bytes_retransmit=0 bytes_invalid=0 send_seq=6740 receive_seq=6740 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999506 adj=49997429 toolboard_t0: mcu_awake=0.204 mcu_task_avg=0.000114 mcu_task_stddev=0.000070 bytes_write=194168 bytes_read=6169889 bytes_retransmit=9 bytes_invalid=0 send_seq=27050 receive_seq=27050 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000253 adj=63997704 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136044 bytes_read=3715550 bytes_retransmit=9 bytes_invalid=0 send_seq=18841 receive_seq=18841 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997438 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40879 bytes_read=1674489 bytes_retransmit=9 bytes_invalid=0 send_seq=6754 receive_seq=6754 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997580 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41365 bytes_read=124566 bytes_retransmit=9 bytes_invalid=0 send_seq=6741 receive_seq=6741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999425 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95457 bytes_read=2560886 bytes_retransmit=0 bytes_invalid=0 send_seq=11300 receive_seq=11300 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998626 coil_temp=17.0 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=53.9 th1: temp=54.8 th2: temp=61.2 th3: temp=58.7 sysload=0.40 cputime=496.991 memavail=7393180 print_time=6583.249 buffer_time=2.124 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6559.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30654269 bytes_read=4775795 bytes_retransmit=9 bytes_invalid=0 send_seq=579294 receive_seq=579294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015983 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40618 bytes_read=127084 bytes_retransmit=0 bytes_invalid=0 send_seq=6741 receive_seq=6741 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999505 adj=49997455 toolboard_t0: mcu_awake=0.204 mcu_task_avg=0.000114 mcu_task_stddev=0.000070 bytes_write=194244 bytes_read=6172947 bytes_retransmit=9 bytes_invalid=0 send_seq=27061 receive_seq=27061 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000250 adj=63997678 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136050 bytes_read=3715678 bytes_retransmit=9 bytes_invalid=0 send_seq=18842 receive_seq=18842 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997460 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40885 bytes_read=1674798 bytes_retransmit=9 bytes_invalid=0 send_seq=6755 receive_seq=6755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997590 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41371 bytes_read=124582 bytes_retransmit=9 bytes_invalid=0 send_seq=6742 receive_seq=6742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95463 bytes_read=2561226 bytes_retransmit=0 bytes_invalid=0 send_seq=11301 receive_seq=11301 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998648 coil_temp=17.0 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=53.9 th1: temp=55.0 th2: temp=61.3 th3: temp=58.6 sysload=0.40 cputime=497.068 memavail=7393180 print_time=6584.145 buffer_time=2.019 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 17 Hz
Testing frequency 18 Hz
Stats 6560.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30657750 bytes_read=4776473 bytes_retransmit=9 bytes_invalid=0 send_seq=579368 receive_seq=579368 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=0 freq=400015981 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40624 bytes_read=127100 bytes_retransmit=0 bytes_invalid=0 send_seq=6742 receive_seq=6742 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999504 adj=49997449 toolboard_t0: mcu_awake=0.204 mcu_task_avg=0.000114 mcu_task_stddev=0.000070 bytes_write=194320 bytes_read=6176005 bytes_retransmit=9 bytes_invalid=0 send_seq=27072 receive_seq=27072 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000255 adj=63997631 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136056 bytes_read=3715778 bytes_retransmit=9 bytes_invalid=0 send_seq=18843 receive_seq=18843 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997461 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40891 bytes_read=1675032 bytes_retransmit=9 bytes_invalid=0 send_seq=6756 receive_seq=6756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997594 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41377 bytes_read=124598 bytes_retransmit=9 bytes_invalid=0 send_seq=6743 receive_seq=6743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95469 bytes_read=2561582 bytes_retransmit=0 bytes_invalid=0 send_seq=11302 receive_seq=11302 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998666 coil_temp=17.0 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=54.1 th1: temp=55.2 th2: temp=61.5 th3: temp=58.9 sysload=0.36 cputime=497.153 memavail=7393180 print_time=6585.398 buffer_time=2.273 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 19 Hz
Stats 6561.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30660643 bytes_read=4777132 bytes_retransmit=9 bytes_invalid=0 send_seq=579432 receive_seq=579432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=0 freq=400015989 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40630 bytes_read=127116 bytes_retransmit=0 bytes_invalid=0 send_seq=6743 receive_seq=6743 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999504 adj=49997464 toolboard_t0: mcu_awake=0.204 mcu_task_avg=0.000114 mcu_task_stddev=0.000070 bytes_write=194396 bytes_read=6179089 bytes_retransmit=9 bytes_invalid=0 send_seq=27083 receive_seq=27083 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000252 adj=63997714 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136062 bytes_read=3715892 bytes_retransmit=9 bytes_invalid=0 send_seq=18844 receive_seq=18844 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997475 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40897 bytes_read=1675266 bytes_retransmit=9 bytes_invalid=0 send_seq=6757 receive_seq=6757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997609 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41383 bytes_read=124614 bytes_retransmit=9 bytes_invalid=0 send_seq=6744 receive_seq=6744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95475 bytes_read=2561938 bytes_retransmit=0 bytes_invalid=0 send_seq=11303 receive_seq=11303 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998660 coil_temp=17.0 refs=0 mcu_temp=20.34 supply_voltage=3.011 th0: temp=54.2 th1: temp=54.9 th2: temp=61.4 th3: temp=58.9 sysload=0.36 cputime=497.229 memavail=7393180 print_time=6586.245 buffer_time=2.120 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 20 Hz
Stats 6562.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30663310 bytes_read=4777757 bytes_retransmit=9 bytes_invalid=0 send_seq=579492 receive_seq=579492 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=400015980 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40636 bytes_read=127145 bytes_retransmit=0 bytes_invalid=0 send_seq=6744 receive_seq=6744 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999503 adj=49997447 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=194472 bytes_read=6182221 bytes_retransmit=9 bytes_invalid=0 send_seq=27094 receive_seq=27094 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000253 adj=63997657 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136068 bytes_read=3716006 bytes_retransmit=9 bytes_invalid=0 send_seq=18845 receive_seq=18845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997462 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40903 bytes_read=1675560 bytes_retransmit=9 bytes_invalid=0 send_seq=6758 receive_seq=6758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997596 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41389 bytes_read=124641 bytes_retransmit=9 bytes_invalid=0 send_seq=6745 receive_seq=6745 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95481 bytes_read=2562294 bytes_retransmit=0 bytes_invalid=0 send_seq=11304 receive_seq=11304 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998654 coil_temp=17.0 refs=0 mcu_temp=20.35 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.0 th2: temp=61.6 th3: temp=58.9 sysload=0.36 cputime=497.307 memavail=7393180 print_time=6587.211 buffer_time=2.085 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 21 Hz
Stats 6563.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30667122 bytes_read=4778462 bytes_retransmit=9 bytes_invalid=0 send_seq=579571 receive_seq=579571 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=0 freq=400015970 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40642 bytes_read=127161 bytes_retransmit=0 bytes_invalid=0 send_seq=6745 receive_seq=6745 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999502 adj=49997463 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=194548 bytes_read=6185278 bytes_retransmit=9 bytes_invalid=0 send_seq=27105 receive_seq=27105 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000250 adj=63997700 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136074 bytes_read=3716106 bytes_retransmit=9 bytes_invalid=0 send_seq=18846 receive_seq=18846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997486 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40909 bytes_read=1675794 bytes_retransmit=9 bytes_invalid=0 send_seq=6759 receive_seq=6759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997614 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41395 bytes_read=124657 bytes_retransmit=9 bytes_invalid=0 send_seq=6746 receive_seq=6746 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95487 bytes_read=2562650 bytes_retransmit=0 bytes_invalid=0 send_seq=11305 receive_seq=11305 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998662 coil_temp=16.9 refs=0 mcu_temp=20.36 supply_voltage=3.011 th0: temp=54.5 th1: temp=55.0 th2: temp=61.6 th3: temp=59.0 sysload=0.36 cputime=497.390 memavail=7393220 print_time=6588.444 buffer_time=2.318 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 22 Hz
Stats 6564.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30670157 bytes_read=4779131 bytes_retransmit=9 bytes_invalid=0 send_seq=579637 receive_seq=579637 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=400015967 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40648 bytes_read=127177 bytes_retransmit=0 bytes_invalid=0 send_seq=6746 receive_seq=6746 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999501 adj=49997480 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=194624 bytes_read=6188365 bytes_retransmit=9 bytes_invalid=0 send_seq=27116 receive_seq=27116 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000248 adj=63997679 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136080 bytes_read=3716234 bytes_retransmit=9 bytes_invalid=0 send_seq=18847 receive_seq=18847 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997508 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40915 bytes_read=1676043 bytes_retransmit=9 bytes_invalid=0 send_seq=6760 receive_seq=6760 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41401 bytes_read=124673 bytes_retransmit=9 bytes_invalid=0 send_seq=6747 receive_seq=6747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95493 bytes_read=2563006 bytes_retransmit=0 bytes_invalid=0 send_seq=11306 receive_seq=11306 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998669 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.011 th0: temp=54.8 th1: temp=55.1 th2: temp=61.7 th3: temp=58.9 sysload=0.36 cputime=497.469 memavail=7389188 print_time=6589.265 buffer_time=2.138 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 23 Hz
Stats 6565.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30673130 bytes_read=4779761 bytes_retransmit=9 bytes_invalid=0 send_seq=579701 receive_seq=579701 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015969 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40654 bytes_read=127193 bytes_retransmit=0 bytes_invalid=0 send_seq=6747 receive_seq=6747 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999501 adj=49997467 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=194700 bytes_read=6191423 bytes_retransmit=9 bytes_invalid=0 send_seq=27127 receive_seq=27127 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000246 adj=63997666 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136086 bytes_read=3716348 bytes_retransmit=9 bytes_invalid=0 send_seq=18848 receive_seq=18848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997513 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40921 bytes_read=1676337 bytes_retransmit=9 bytes_invalid=0 send_seq=6761 receive_seq=6761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41407 bytes_read=124689 bytes_retransmit=9 bytes_invalid=0 send_seq=6748 receive_seq=6748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95499 bytes_read=2563362 bytes_retransmit=0 bytes_invalid=0 send_seq=11307 receive_seq=11307 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998668 coil_temp=16.9 refs=0 mcu_temp=20.36 supply_voltage=3.011 th0: temp=54.6 th1: temp=55.0 th2: temp=61.7 th3: temp=59.1 sysload=0.34 cputime=497.557 memavail=7393600 print_time=6590.240 buffer_time=2.112 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 24 Hz
Stats 6566.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30677212 bytes_read=4780486 bytes_retransmit=9 bytes_invalid=0 send_seq=579784 receive_seq=579784 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015980 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40660 bytes_read=127209 bytes_retransmit=0 bytes_invalid=0 send_seq=6748 receive_seq=6748 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999501 adj=49997477 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=194769 bytes_read=6194456 bytes_retransmit=9 bytes_invalid=0 send_seq=27137 receive_seq=27137 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000243 adj=63997644 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136092 bytes_read=3716448 bytes_retransmit=9 bytes_invalid=0 send_seq=18849 receive_seq=18849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997508 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40927 bytes_read=1676571 bytes_retransmit=9 bytes_invalid=0 send_seq=6762 receive_seq=6762 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41413 bytes_read=124705 bytes_retransmit=9 bytes_invalid=0 send_seq=6749 receive_seq=6749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95505 bytes_read=2563718 bytes_retransmit=0 bytes_invalid=0 send_seq=11308 receive_seq=11308 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998656 coil_temp=16.9 refs=0 mcu_temp=20.36 supply_voltage=3.011 th0: temp=54.9 th1: temp=55.0 th2: temp=61.8 th3: temp=59.2 sysload=0.34 cputime=497.640 memavail=7393600 print_time=6591.461 buffer_time=2.332 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 25 Hz
Stats 6567.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30680502 bytes_read=4781196 bytes_retransmit=9 bytes_invalid=0 send_seq=579855 receive_seq=579855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=0 freq=400015979 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40666 bytes_read=127225 bytes_retransmit=0 bytes_invalid=0 send_seq=6749 receive_seq=6749 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999500 adj=49997465 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=194845 bytes_read=6197559 bytes_retransmit=9 bytes_invalid=0 send_seq=27148 receive_seq=27148 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000241 adj=63997604 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136098 bytes_read=3716562 bytes_retransmit=9 bytes_invalid=0 send_seq=18850 receive_seq=18850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997485 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40933 bytes_read=1676805 bytes_retransmit=9 bytes_invalid=0 send_seq=6763 receive_seq=6763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997621 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41419 bytes_read=124732 bytes_retransmit=9 bytes_invalid=0 send_seq=6750 receive_seq=6750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95511 bytes_read=2564074 bytes_retransmit=0 bytes_invalid=0 send_seq=11309 receive_seq=11309 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998637 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.011 th0: temp=54.9 th1: temp=55.1 th2: temp=61.8 th3: temp=59.2 sysload=0.34 cputime=497.719 memavail=7392368 print_time=6592.300 buffer_time=2.170 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 26 Hz
Stats 6568.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30683763 bytes_read=4781851 bytes_retransmit=9 bytes_invalid=0 send_seq=579924 receive_seq=579924 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=0 freq=400015979 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40672 bytes_read=127254 bytes_retransmit=0 bytes_invalid=0 send_seq=6750 receive_seq=6750 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999501 adj=49997467 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=194921 bytes_read=6200617 bytes_retransmit=9 bytes_invalid=0 send_seq=27159 receive_seq=27159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997579 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136104 bytes_read=3716676 bytes_retransmit=9 bytes_invalid=0 send_seq=18851 receive_seq=18851 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=40939 bytes_read=1677099 bytes_retransmit=9 bytes_invalid=0 send_seq=6764 receive_seq=6764 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41425 bytes_read=124748 bytes_retransmit=9 bytes_invalid=0 send_seq=6751 receive_seq=6751 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95517 bytes_read=2564430 bytes_retransmit=0 bytes_invalid=0 send_seq=11310 receive_seq=11310 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998634 coil_temp=16.9 refs=0 mcu_temp=20.36 supply_voltage=3.011 th0: temp=54.9 th1: temp=55.1 th2: temp=61.9 th3: temp=59.3 sysload=0.34 cputime=497.801 memavail=7392368 print_time=6593.277 buffer_time=2.147 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6569.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30687153 bytes_read=4782521 bytes_retransmit=9 bytes_invalid=0 send_seq=579996 receive_seq=579996 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015981 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40678 bytes_read=127270 bytes_retransmit=0 bytes_invalid=0 send_seq=6751 receive_seq=6751 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999501 adj=49997484 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=194997 bytes_read=6203732 bytes_retransmit=9 bytes_invalid=0 send_seq=27170 receive_seq=27170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997563 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136110 bytes_read=3716776 bytes_retransmit=9 bytes_invalid=0 send_seq=18852 receive_seq=18852 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=40945 bytes_read=1677348 bytes_retransmit=9 bytes_invalid=0 send_seq=6765 receive_seq=6765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997623 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41431 bytes_read=124764 bytes_retransmit=9 bytes_invalid=0 send_seq=6752 receive_seq=6752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95523 bytes_read=2564786 bytes_retransmit=0 bytes_invalid=0 send_seq=11311 receive_seq=11311 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998630 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.011 th0: temp=55.0 th1: temp=55.0 th2: temp=61.9 th3: temp=59.4 sysload=0.34 cputime=497.881 memavail=7392368 print_time=6594.146 buffer_time=2.014 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 27 Hz
Testing frequency 28 Hz
Stats 6570.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30690729 bytes_read=4783231 bytes_retransmit=9 bytes_invalid=0 send_seq=580071 receive_seq=580071 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015993 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40684 bytes_read=127286 bytes_retransmit=0 bytes_invalid=0 send_seq=6752 receive_seq=6752 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999499 adj=49997472 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=195073 bytes_read=6206817 bytes_retransmit=9 bytes_invalid=0 send_seq=27181 receive_seq=27181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000244 adj=63997538 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136116 bytes_read=3716904 bytes_retransmit=9 bytes_invalid=0 send_seq=18853 receive_seq=18853 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997584 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=40951 bytes_read=1677582 bytes_retransmit=9 bytes_invalid=0 send_seq=6766 receive_seq=6766 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41437 bytes_read=124780 bytes_retransmit=9 bytes_invalid=0 send_seq=6753 receive_seq=6753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95529 bytes_read=2565142 bytes_retransmit=0 bytes_invalid=0 send_seq=11312 receive_seq=11312 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998698 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.011 th0: temp=55.1 th1: temp=55.2 th2: temp=61.8 th3: temp=59.4 sysload=0.31 cputime=497.965 memavail=7392384 print_time=6595.121 buffer_time=1.990 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 29 Hz
Stats 6571.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30695199 bytes_read=4783990 bytes_retransmit=9 bytes_invalid=0 send_seq=580161 receive_seq=580161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=0 freq=400015986 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40690 bytes_read=127302 bytes_retransmit=0 bytes_invalid=0 send_seq=6753 receive_seq=6753 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999499 adj=49997445 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=195149 bytes_read=6209873 bytes_retransmit=9 bytes_invalid=0 send_seq=27192 receive_seq=27192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000241 adj=63997651 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136122 bytes_read=3717018 bytes_retransmit=9 bytes_invalid=0 send_seq=18854 receive_seq=18854 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=40957 bytes_read=1677876 bytes_retransmit=9 bytes_invalid=0 send_seq=6767 receive_seq=6767 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997605 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41443 bytes_read=124796 bytes_retransmit=9 bytes_invalid=0 send_seq=6754 receive_seq=6754 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95535 bytes_read=2565498 bytes_retransmit=0 bytes_invalid=0 send_seq=11313 receive_seq=11313 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998668 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=55.1 th1: temp=55.1 th2: temp=61.9 th3: temp=59.4 sysload=0.31 cputime=498.053 memavail=7392384 print_time=6596.332 buffer_time=2.199 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 30 Hz
Stats 6572.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30698369 bytes_read=4784661 bytes_retransmit=9 bytes_invalid=0 send_seq=580230 receive_seq=580230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015981 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40696 bytes_read=127318 bytes_retransmit=0 bytes_invalid=0 send_seq=6754 receive_seq=6754 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999498 adj=49997460 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=195225 bytes_read=6212948 bytes_retransmit=9 bytes_invalid=0 send_seq=27203 receive_seq=27203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997624 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136128 bytes_read=3717118 bytes_retransmit=9 bytes_invalid=0 send_seq=18855 receive_seq=18855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=40963 bytes_read=1678110 bytes_retransmit=9 bytes_invalid=0 send_seq=6768 receive_seq=6768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997630 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41449 bytes_read=124823 bytes_retransmit=9 bytes_invalid=0 send_seq=6755 receive_seq=6755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95541 bytes_read=2565854 bytes_retransmit=0 bytes_invalid=0 send_seq=11314 receive_seq=11314 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998671 coil_temp=16.9 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=55.4 th1: temp=55.1 th2: temp=62.0 th3: temp=59.4 sysload=0.31 cputime=498.134 memavail=7392384 print_time=6597.178 buffer_time=2.045 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6573.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30702250 bytes_read=4785400 bytes_retransmit=9 bytes_invalid=0 send_seq=580310 receive_seq=580310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015996 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40702 bytes_read=127347 bytes_retransmit=0 bytes_invalid=0 send_seq=6755 receive_seq=6755 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999498 adj=49997470 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=195301 bytes_read=6216032 bytes_retransmit=9 bytes_invalid=0 send_seq=27214 receive_seq=27214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997601 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136134 bytes_read=3717232 bytes_retransmit=9 bytes_invalid=0 send_seq=18856 receive_seq=18856 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997552 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=40969 bytes_read=1678344 bytes_retransmit=9 bytes_invalid=0 send_seq=6769 receive_seq=6769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41455 bytes_read=124839 bytes_retransmit=9 bytes_invalid=0 send_seq=6756 receive_seq=6756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95547 bytes_read=2566210 bytes_retransmit=0 bytes_invalid=0 send_seq=11315 receive_seq=11315 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998665 coil_temp=16.9 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=55.2 th1: temp=55.2 th2: temp=62.1 th3: temp=59.5 sysload=0.31 cputime=498.216 memavail=7392384 print_time=6598.139 buffer_time=2.006 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 31 Hz
Testing frequency 32 Hz
Stats 6574.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30706876 bytes_read=4786175 bytes_retransmit=9 bytes_invalid=0 send_seq=580403 receive_seq=580403 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400016026 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40708 bytes_read=127363 bytes_retransmit=0 bytes_invalid=0 send_seq=6756 receive_seq=6756 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999498 adj=49997450 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=195377 bytes_read=6219089 bytes_retransmit=9 bytes_invalid=0 send_seq=27225 receive_seq=27225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997550 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136140 bytes_read=3717346 bytes_retransmit=9 bytes_invalid=0 send_seq=18857 receive_seq=18857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40975 bytes_read=1678653 bytes_retransmit=9 bytes_invalid=0 send_seq=6770 receive_seq=6770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41461 bytes_read=124855 bytes_retransmit=9 bytes_invalid=0 send_seq=6757 receive_seq=6757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95553 bytes_read=2566566 bytes_retransmit=0 bytes_invalid=0 send_seq=11316 receive_seq=11316 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998638 coil_temp=16.9 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=55.4 th1: temp=55.3 th2: temp=62.1 th3: temp=59.5 sysload=0.31 cputime=498.308 memavail=7392384 print_time=6599.352 buffer_time=2.219 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 33 Hz
Stats 6575.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30710149 bytes_read=4786835 bytes_retransmit=9 bytes_invalid=0 send_seq=580473 receive_seq=580473 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=46 upcoming_bytes=0 freq=400016016 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40714 bytes_read=127379 bytes_retransmit=0 bytes_invalid=0 send_seq=6757 receive_seq=6757 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999497 adj=49997415 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=195453 bytes_read=6222146 bytes_retransmit=9 bytes_invalid=0 send_seq=27236 receive_seq=27236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997513 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136146 bytes_read=3717460 bytes_retransmit=9 bytes_invalid=0 send_seq=18858 receive_seq=18858 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000075 adj=63997467 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40981 bytes_read=1678887 bytes_retransmit=9 bytes_invalid=0 send_seq=6771 receive_seq=6771 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997598 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41467 bytes_read=124871 bytes_retransmit=9 bytes_invalid=0 send_seq=6758 receive_seq=6758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999425 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95559 bytes_read=2566922 bytes_retransmit=0 bytes_invalid=0 send_seq=11317 receive_seq=11317 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998619 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=55.5 th1: temp=55.3 th2: temp=62.0 th3: temp=59.6 sysload=0.28 cputime=498.389 memavail=7392400 print_time=6600.227 buffer_time=2.093 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6576.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30714342 bytes_read=4787594 bytes_retransmit=9 bytes_invalid=0 send_seq=580557 receive_seq=580557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016015 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40720 bytes_read=127395 bytes_retransmit=0 bytes_invalid=0 send_seq=6758 receive_seq=6758 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999496 adj=49997432 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=195529 bytes_read=6225231 bytes_retransmit=9 bytes_invalid=0 send_seq=27247 receive_seq=27247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997530 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136152 bytes_read=3717574 bytes_retransmit=9 bytes_invalid=0 send_seq=18859 receive_seq=18859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000075 adj=63997674 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40987 bytes_read=1679121 bytes_retransmit=9 bytes_invalid=0 send_seq=6772 receive_seq=6772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41473 bytes_read=124887 bytes_retransmit=9 bytes_invalid=0 send_seq=6759 receive_seq=6759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95565 bytes_read=2567278 bytes_retransmit=0 bytes_invalid=0 send_seq=11318 receive_seq=11318 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998625 coil_temp=16.9 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=55.5 th1: temp=55.3 th2: temp=62.1 th3: temp=59.6 sysload=0.28 cputime=498.472 memavail=7392400 print_time=6601.168 buffer_time=2.034 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 34 Hz
Testing frequency 35 Hz
Stats 6577.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30719339 bytes_read=4788410 bytes_retransmit=9 bytes_invalid=0 send_seq=580655 receive_seq=580655 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=0 freq=400016007 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40726 bytes_read=127411 bytes_retransmit=0 bytes_invalid=0 send_seq=6759 receive_seq=6759 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999494 adj=49997424 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=195605 bytes_read=6228362 bytes_retransmit=9 bytes_invalid=0 send_seq=27258 receive_seq=27258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997569 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136158 bytes_read=3717688 bytes_retransmit=9 bytes_invalid=0 send_seq=18860 receive_seq=18860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000074 adj=63997654 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40993 bytes_read=1679415 bytes_retransmit=9 bytes_invalid=0 send_seq=6773 receive_seq=6773 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41479 bytes_read=124914 bytes_retransmit=9 bytes_invalid=0 send_seq=6760 receive_seq=6760 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95571 bytes_read=2567634 bytes_retransmit=0 bytes_invalid=0 send_seq=11319 receive_seq=11319 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998683 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=55.5 th1: temp=55.0 th2: temp=62.1 th3: temp=59.6 sysload=0.28 cputime=498.566 memavail=7395736 print_time=6602.390 buffer_time=2.256 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 36 Hz
Stats 6578.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30722691 bytes_read=4789075 bytes_retransmit=9 bytes_invalid=0 send_seq=580726 receive_seq=580726 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=0 freq=400015995 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=40732 bytes_read=127440 bytes_retransmit=0 bytes_invalid=0 send_seq=6760 receive_seq=6760 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999494 adj=49997442 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=195681 bytes_read=6231419 bytes_retransmit=9 bytes_invalid=0 send_seq=27269 receive_seq=27269 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997586 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136164 bytes_read=3717788 bytes_retransmit=9 bytes_invalid=0 send_seq=18861 receive_seq=18861 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997620 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=40999 bytes_read=1679649 bytes_retransmit=9 bytes_invalid=0 send_seq=6774 receive_seq=6774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41485 bytes_read=124930 bytes_retransmit=9 bytes_invalid=0 send_seq=6761 receive_seq=6761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95577 bytes_read=2567990 bytes_retransmit=0 bytes_invalid=0 send_seq=11320 receive_seq=11320 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998677 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=55.5 th1: temp=55.2 th2: temp=62.2 th3: temp=59.6 sysload=0.28 cputime=498.648 memavail=7395772 print_time=6603.254 buffer_time=2.120 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6579.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30727144 bytes_read=4789870 bytes_retransmit=9 bytes_invalid=0 send_seq=580815 receive_seq=580815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015991 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=40744 bytes_read=127472 bytes_retransmit=0 bytes_invalid=0 send_seq=6762 receive_seq=6762 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999495 adj=49997464 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=195763 bytes_read=6234522 bytes_retransmit=9 bytes_invalid=0 send_seq=27281 receive_seq=27281 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997592 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136176 bytes_read=3717918 bytes_retransmit=9 bytes_invalid=0 send_seq=18863 receive_seq=18863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000079 adj=63997614 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41011 bytes_read=1679914 bytes_retransmit=9 bytes_invalid=0 send_seq=6776 receive_seq=6776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41497 bytes_read=124962 bytes_retransmit=9 bytes_invalid=0 send_seq=6763 receive_seq=6763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95589 bytes_read=2568362 bytes_retransmit=0 bytes_invalid=0 send_seq=11322 receive_seq=11322 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998704 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=55.5 th1: temp=55.0 th2: temp=62.4 th3: temp=59.6 sysload=0.28 cputime=498.733 memavail=7395528 print_time=6604.199 buffer_time=2.064 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 37 Hz
Testing frequency 38 Hz
Stats 6580.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30731975 bytes_read=4790650 bytes_retransmit=9 bytes_invalid=0 send_seq=580909 receive_seq=580909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=375 freq=400016003 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=40750 bytes_read=127488 bytes_retransmit=0 bytes_invalid=0 send_seq=6763 receive_seq=6763 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999499 adj=49997480 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=195839 bytes_read=6237578 bytes_retransmit=9 bytes_invalid=0 send_seq=27292 receive_seq=27292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000239 adj=63997757 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136182 bytes_read=3718046 bytes_retransmit=9 bytes_invalid=0 send_seq=18864 receive_seq=18864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000077 adj=63997681 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41017 bytes_read=1680208 bytes_retransmit=9 bytes_invalid=0 send_seq=6777 receive_seq=6777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41503 bytes_read=124978 bytes_retransmit=9 bytes_invalid=0 send_seq=6764 receive_seq=6764 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95595 bytes_read=2568718 bytes_retransmit=0 bytes_invalid=0 send_seq=11323 receive_seq=11323 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998716 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=55.8 th1: temp=55.3 th2: temp=62.4 th3: temp=59.6 sysload=0.26 cputime=498.828 memavail=7395312 print_time=6605.396 buffer_time=2.261 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 39 Hz
Stats 6581.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30735880 bytes_read=4791356 bytes_retransmit=9 bytes_invalid=0 send_seq=580989 receive_seq=580989 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016000 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=40756 bytes_read=127504 bytes_retransmit=0 bytes_invalid=0 send_seq=6764 receive_seq=6764 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999497 adj=49997515 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=195915 bytes_read=6240634 bytes_retransmit=9 bytes_invalid=0 send_seq=27303 receive_seq=27303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997698 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136188 bytes_read=3718146 bytes_retransmit=9 bytes_invalid=0 send_seq=18865 receive_seq=18865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000075 adj=63997592 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41023 bytes_read=1680442 bytes_retransmit=9 bytes_invalid=0 send_seq=6778 receive_seq=6778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41509 bytes_read=124994 bytes_retransmit=9 bytes_invalid=0 send_seq=6765 receive_seq=6765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95601 bytes_read=2569074 bytes_retransmit=0 bytes_invalid=0 send_seq=11324 receive_seq=11324 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998677 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=55.7 th1: temp=55.3 th2: temp=62.3 th3: temp=59.7 sysload=0.26 cputime=498.916 memavail=7395312 print_time=6606.277 buffer_time=2.141 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 40 Hz
Stats 6582.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30740323 bytes_read=4792151 bytes_retransmit=9 bytes_invalid=0 send_seq=581077 receive_seq=581077 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=116 freq=400016005 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=40762 bytes_read=127520 bytes_retransmit=0 bytes_invalid=0 send_seq=6765 receive_seq=6765 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999495 adj=49997499 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=195984 bytes_read=6243712 bytes_retransmit=9 bytes_invalid=0 send_seq=27313 receive_seq=27313 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000245 adj=63997715 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136194 bytes_read=3718260 bytes_retransmit=9 bytes_invalid=0 send_seq=18866 receive_seq=18866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000074 adj=63997567 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41029 bytes_read=1680676 bytes_retransmit=9 bytes_invalid=0 send_seq=6779 receive_seq=6779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41515 bytes_read=125021 bytes_retransmit=9 bytes_invalid=0 send_seq=6766 receive_seq=6766 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95607 bytes_read=2569430 bytes_retransmit=0 bytes_invalid=0 send_seq=11325 receive_seq=11325 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998681 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=55.8 th1: temp=55.4 th2: temp=62.4 th3: temp=59.7 sysload=0.26 cputime=499.015 memavail=7395408 print_time=6607.225 buffer_time=2.090 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 41 Hz
Stats 6583.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30745020 bytes_read=4792911 bytes_retransmit=9 bytes_invalid=0 send_seq=581167 receive_seq=581167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=955 freq=400016029 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40768 bytes_read=127549 bytes_retransmit=0 bytes_invalid=0 send_seq=6766 receive_seq=6766 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999495 adj=49997470 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=196060 bytes_read=6246770 bytes_retransmit=9 bytes_invalid=0 send_seq=27324 receive_seq=27324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000242 adj=63997758 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136200 bytes_read=3718374 bytes_retransmit=9 bytes_invalid=0 send_seq=18867 receive_seq=18867 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000072 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41035 bytes_read=1680970 bytes_retransmit=9 bytes_invalid=0 send_seq=6780 receive_seq=6780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997626 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41521 bytes_read=125037 bytes_retransmit=9 bytes_invalid=0 send_seq=6767 receive_seq=6767 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95613 bytes_read=2569786 bytes_retransmit=0 bytes_invalid=0 send_seq=11326 receive_seq=11326 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998659 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=55.7 th1: temp=55.4 th2: temp=62.3 th3: temp=59.7 sysload=0.26 cputime=499.109 memavail=7397020 print_time=6608.432 buffer_time=2.296 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 42 Hz
Stats 6584.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30749682 bytes_read=4793666 bytes_retransmit=9 bytes_invalid=0 send_seq=581256 receive_seq=581256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=38 freq=400016042 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40774 bytes_read=127565 bytes_retransmit=0 bytes_invalid=0 send_seq=6767 receive_seq=6767 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999495 adj=49997437 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=196136 bytes_read=6249827 bytes_retransmit=9 bytes_invalid=0 send_seq=27335 receive_seq=27335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000245 adj=63997657 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136206 bytes_read=3718474 bytes_retransmit=9 bytes_invalid=0 send_seq=18868 receive_seq=18868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997458 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41041 bytes_read=1681219 bytes_retransmit=9 bytes_invalid=0 send_seq=6781 receive_seq=6781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997601 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41527 bytes_read=125053 bytes_retransmit=9 bytes_invalid=0 send_seq=6768 receive_seq=6768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95619 bytes_read=2570142 bytes_retransmit=0 bytes_invalid=0 send_seq=11327 receive_seq=11327 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998631 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=55.8 th1: temp=55.3 th2: temp=62.4 th3: temp=59.7 sysload=0.26 cputime=499.202 memavail=7397020 print_time=6609.320 buffer_time=2.184 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 43 Hz
Stats 6585.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30753717 bytes_read=4794410 bytes_retransmit=9 bytes_invalid=0 send_seq=581337 receive_seq=581337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=785 freq=400016048 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40780 bytes_read=127581 bytes_retransmit=0 bytes_invalid=0 send_seq=6768 receive_seq=6768 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999494 adj=49997425 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=196212 bytes_read=6252970 bytes_retransmit=9 bytes_invalid=0 send_seq=27346 receive_seq=27346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000243 adj=63997674 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136212 bytes_read=3718602 bytes_retransmit=9 bytes_invalid=0 send_seq=18869 receive_seq=18869 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997424 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41047 bytes_read=1681453 bytes_retransmit=9 bytes_invalid=0 send_seq=6782 receive_seq=6782 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997582 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41533 bytes_read=125069 bytes_retransmit=9 bytes_invalid=0 send_seq=6769 receive_seq=6769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999420 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95625 bytes_read=2570498 bytes_retransmit=0 bytes_invalid=0 send_seq=11328 receive_seq=11328 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998609 coil_temp=16.9 refs=0 mcu_temp=20.32 supply_voltage=3.012 th0: temp=55.7 th1: temp=55.3 th2: temp=62.5 th3: temp=59.8 sysload=0.24 cputime=499.292 memavail=7397024 print_time=6610.231 buffer_time=2.094 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 44 Hz
Stats 6586.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=30758354 bytes_read=4795165 bytes_retransmit=9 bytes_invalid=0 send_seq=581426 receive_seq=581426 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016046 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40786 bytes_read=127597 bytes_retransmit=0 bytes_invalid=0 send_seq=6769 receive_seq=6769 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999493 adj=49997413 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=196288 bytes_read=6256026 bytes_retransmit=9 bytes_invalid=0 send_seq=27357 receive_seq=27357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997640 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136218 bytes_read=3718716 bytes_retransmit=9 bytes_invalid=0 send_seq=18870 receive_seq=18870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997407 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41053 bytes_read=1681747 bytes_retransmit=9 bytes_invalid=0 send_seq=6783 receive_seq=6783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997574 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41539 bytes_read=125085 bytes_retransmit=9 bytes_invalid=0 send_seq=6770 receive_seq=6770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999421 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95631 bytes_read=2570854 bytes_retransmit=0 bytes_invalid=0 send_seq=11329 receive_seq=11329 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998622 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=55.9 th1: temp=55.5 th2: temp=62.5 th3: temp=59.8 sysload=0.24 cputime=499.386 memavail=7397024 print_time=6611.128 buffer_time=1.990 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 45 Hz
Stats 6587.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=30763824 bytes_read=4796006 bytes_retransmit=9 bytes_invalid=0 send_seq=581529 receive_seq=581529 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=254 freq=400016050 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40792 bytes_read=127613 bytes_retransmit=0 bytes_invalid=0 send_seq=6770 receive_seq=6770 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999493 adj=49997415 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=196364 bytes_read=6259100 bytes_retransmit=9 bytes_invalid=0 send_seq=27368 receive_seq=27368 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000245 adj=63997608 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136224 bytes_read=3718816 bytes_retransmit=9 bytes_invalid=0 send_seq=18871 receive_seq=18871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997405 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41059 bytes_read=1681981 bytes_retransmit=9 bytes_invalid=0 send_seq=6784 receive_seq=6784 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997582 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41545 bytes_read=125112 bytes_retransmit=9 bytes_invalid=0 send_seq=6771 receive_seq=6771 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999422 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95637 bytes_read=2571210 bytes_retransmit=0 bytes_invalid=0 send_seq=11330 receive_seq=11330 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998617 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=55.7 th1: temp=55.4 th2: temp=62.4 th3: temp=59.8 sysload=0.24 cputime=499.490 memavail=7395728 print_time=6612.335 buffer_time=2.197 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 46 Hz
Stats 6588.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=30767886 bytes_read=4796735 bytes_retransmit=9 bytes_invalid=0 send_seq=581607 receive_seq=581607 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=1131 freq=400016045 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40798 bytes_read=127642 bytes_retransmit=0 bytes_invalid=0 send_seq=6771 receive_seq=6771 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999491 adj=49997422 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=196440 bytes_read=6262185 bytes_retransmit=9 bytes_invalid=0 send_seq=27379 receive_seq=27379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000241 adj=63997675 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136230 bytes_read=3718930 bytes_retransmit=9 bytes_invalid=0 send_seq=18872 receive_seq=18872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997413 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41065 bytes_read=1682215 bytes_retransmit=9 bytes_invalid=0 send_seq=6785 receive_seq=6785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997597 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41551 bytes_read=125128 bytes_retransmit=9 bytes_invalid=0 send_seq=6772 receive_seq=6772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95643 bytes_read=2571566 bytes_retransmit=0 bytes_invalid=0 send_seq=11331 receive_seq=11331 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998620 coil_temp=16.9 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=55.9 th1: temp=55.4 th2: temp=62.5 th3: temp=59.9 sysload=0.24 cputime=499.585 memavail=7395800 print_time=6613.257 buffer_time=2.118 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6589.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=30772914 bytes_read=4797525 bytes_retransmit=9 bytes_invalid=0 send_seq=581703 receive_seq=581703 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400016033 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40804 bytes_read=127658 bytes_retransmit=0 bytes_invalid=0 send_seq=6772 receive_seq=6772 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999490 adj=49997423 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=196516 bytes_read=6265241 bytes_retransmit=9 bytes_invalid=0 send_seq=27390 receive_seq=27390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000244 adj=63997643 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136236 bytes_read=3719044 bytes_retransmit=9 bytes_invalid=0 send_seq=18873 receive_seq=18873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997422 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41071 bytes_read=1682524 bytes_retransmit=9 bytes_invalid=0 send_seq=6786 receive_seq=6786 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997606 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41557 bytes_read=125144 bytes_retransmit=9 bytes_invalid=0 send_seq=6773 receive_seq=6773 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95649 bytes_read=2571922 bytes_retransmit=0 bytes_invalid=0 send_seq=11332 receive_seq=11332 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998626 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.1 th2: temp=62.4 th3: temp=59.9 sysload=0.24 cputime=499.681 memavail=7395800 print_time=6614.150 buffer_time=2.011 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 47 Hz
Testing frequency 48 Hz
Stats 6590.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=30778247 bytes_read=4798340 bytes_retransmit=9 bytes_invalid=0 send_seq=581804 receive_seq=581804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=23 upcoming_bytes=413 freq=400016063 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40810 bytes_read=127674 bytes_retransmit=0 bytes_invalid=0 send_seq=6773 receive_seq=6773 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999489 adj=49997430 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=196592 bytes_read=6268299 bytes_retransmit=9 bytes_invalid=0 send_seq=27401 receive_seq=27401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000242 adj=63997713 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136242 bytes_read=3719158 bytes_retransmit=9 bytes_invalid=0 send_seq=18874 receive_seq=18874 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997457 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41077 bytes_read=1682758 bytes_retransmit=9 bytes_invalid=0 send_seq=6787 receive_seq=6787 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41563 bytes_read=125160 bytes_retransmit=9 bytes_invalid=0 send_seq=6774 receive_seq=6774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95655 bytes_read=2572278 bytes_retransmit=0 bytes_invalid=0 send_seq=11333 receive_seq=11333 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998631 coil_temp=16.9 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.4 th2: temp=62.4 th3: temp=60.0 sysload=0.22 cputime=499.786 memavail=7395800 print_time=6615.354 buffer_time=2.215 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 49 Hz
Stats 6591.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000005 bytes_write=30782416 bytes_read=4799082 bytes_retransmit=9 bytes_invalid=0 send_seq=581885 receive_seq=581885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=1345 freq=400016090 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40816 bytes_read=127690 bytes_retransmit=0 bytes_invalid=0 send_seq=6774 receive_seq=6774 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999489 adj=49997394 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=196668 bytes_read=6271383 bytes_retransmit=9 bytes_invalid=0 send_seq=27412 receive_seq=27412 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000248 adj=63997622 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136248 bytes_read=3719272 bytes_retransmit=9 bytes_invalid=0 send_seq=18875 receive_seq=18875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997413 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41083 bytes_read=1682992 bytes_retransmit=9 bytes_invalid=0 send_seq=6788 receive_seq=6788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997588 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41569 bytes_read=125176 bytes_retransmit=9 bytes_invalid=0 send_seq=6775 receive_seq=6775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95661 bytes_read=2572634 bytes_retransmit=0 bytes_invalid=0 send_seq=11334 receive_seq=11334 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998599 coil_temp=16.9 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.2 th2: temp=62.5 th3: temp=59.8 sysload=0.22 cputime=499.881 memavail=7395800 print_time=6616.275 buffer_time=2.135 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6592.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30787557 bytes_read=4799901 bytes_retransmit=9 bytes_invalid=0 send_seq=581984 receive_seq=581984 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=290 freq=400016073 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40822 bytes_read=127706 bytes_retransmit=0 bytes_invalid=0 send_seq=6775 receive_seq=6775 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999491 adj=49997361 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=196744 bytes_read=6274458 bytes_retransmit=9 bytes_invalid=0 send_seq=27423 receive_seq=27423 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000245 adj=63997646 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136254 bytes_read=3719386 bytes_retransmit=9 bytes_invalid=0 send_seq=18876 receive_seq=18876 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997357 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41089 bytes_read=1683286 bytes_retransmit=9 bytes_invalid=0 send_seq=6789 receive_seq=6789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997560 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41575 bytes_read=125203 bytes_retransmit=9 bytes_invalid=0 send_seq=6776 receive_seq=6776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999419 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95667 bytes_read=2572990 bytes_retransmit=0 bytes_invalid=0 send_seq=11335 receive_seq=11335 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998570 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=55.9 th1: temp=55.3 th2: temp=62.4 th3: temp=59.8 sysload=0.22 cputime=499.977 memavail=7395800 print_time=6617.174 buffer_time=2.033 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 50 Hz
Testing frequency 51 Hz
Stats 6593.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30792921 bytes_read=4800716 bytes_retransmit=9 bytes_invalid=0 send_seq=582085 receive_seq=582085 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=845 freq=400016054 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40828 bytes_read=127735 bytes_retransmit=0 bytes_invalid=0 send_seq=6776 receive_seq=6776 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999492 adj=49997427 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=196820 bytes_read=6277574 bytes_retransmit=9 bytes_invalid=0 send_seq=27434 receive_seq=27434 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000241 adj=63997638 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136260 bytes_read=3719486 bytes_retransmit=9 bytes_invalid=0 send_seq=18877 receive_seq=18877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997416 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41095 bytes_read=1683520 bytes_retransmit=9 bytes_invalid=0 send_seq=6790 receive_seq=6790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997592 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41581 bytes_read=125219 bytes_retransmit=9 bytes_invalid=0 send_seq=6777 receive_seq=6777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95673 bytes_read=2573346 bytes_retransmit=0 bytes_invalid=0 send_seq=11336 receive_seq=11336 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998588 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=55.9 th1: temp=55.3 th2: temp=62.4 th3: temp=59.9 sysload=0.22 cputime=500.084 memavail=7395828 print_time=6618.370 buffer_time=2.230 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 52 Hz
Stats 6594.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30797322 bytes_read=4801485 bytes_retransmit=9 bytes_invalid=0 send_seq=582171 receive_seq=582171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=46 upcoming_bytes=1654 freq=400016064 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40834 bytes_read=127751 bytes_retransmit=0 bytes_invalid=0 send_seq=6777 receive_seq=6777 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999492 adj=49997482 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=196896 bytes_read=6280658 bytes_retransmit=9 bytes_invalid=0 send_seq=27445 receive_seq=27445 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997644 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136266 bytes_read=3719614 bytes_retransmit=9 bytes_invalid=0 send_seq=18878 receive_seq=18878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997467 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41101 bytes_read=1683769 bytes_retransmit=9 bytes_invalid=0 send_seq=6791 receive_seq=6791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41587 bytes_read=125235 bytes_retransmit=9 bytes_invalid=0 send_seq=6778 receive_seq=6778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95679 bytes_read=2573702 bytes_retransmit=0 bytes_invalid=0 send_seq=11337 receive_seq=11337 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998623 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.4 th2: temp=62.6 th3: temp=59.8 sysload=0.22 cputime=500.180 memavail=7395576 print_time=6619.286 buffer_time=2.145 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6595.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30802703 bytes_read=4802295 bytes_retransmit=9 bytes_invalid=0 send_seq=582271 receive_seq=582271 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=570 freq=400016062 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40840 bytes_read=127767 bytes_retransmit=0 bytes_invalid=0 send_seq=6778 receive_seq=6778 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999491 adj=49997469 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=196972 bytes_read=6283714 bytes_retransmit=9 bytes_invalid=0 send_seq=27456 receive_seq=27456 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997607 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136272 bytes_read=3719728 bytes_retransmit=9 bytes_invalid=0 send_seq=18879 receive_seq=18879 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997485 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41107 bytes_read=1684063 bytes_retransmit=9 bytes_invalid=0 send_seq=6792 receive_seq=6792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997607 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41593 bytes_read=125251 bytes_retransmit=9 bytes_invalid=0 send_seq=6779 receive_seq=6779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95685 bytes_read=2574058 bytes_retransmit=0 bytes_invalid=0 send_seq=11338 receive_seq=11338 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998620 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.4 th2: temp=62.7 th3: temp=59.9 sysload=0.20 cputime=500.278 memavail=7395324 print_time=6620.190 buffer_time=2.048 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 53 Hz
Testing frequency 54 Hz
Stats 6596.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30808245 bytes_read=4803130 bytes_retransmit=9 bytes_invalid=0 send_seq=582376 receive_seq=582376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=1170 freq=400016053 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40846 bytes_read=127783 bytes_retransmit=0 bytes_invalid=0 send_seq=6779 receive_seq=6779 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999491 adj=49997467 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=197048 bytes_read=6286773 bytes_retransmit=9 bytes_invalid=0 send_seq=27467 receive_seq=27467 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997593 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136278 bytes_read=3719828 bytes_retransmit=9 bytes_invalid=0 send_seq=18880 receive_seq=18880 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997486 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41113 bytes_read=1684297 bytes_retransmit=9 bytes_invalid=0 send_seq=6793 receive_seq=6793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997608 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41599 bytes_read=125267 bytes_retransmit=9 bytes_invalid=0 send_seq=6780 receive_seq=6780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95691 bytes_read=2574414 bytes_retransmit=0 bytes_invalid=0 send_seq=11339 receive_seq=11339 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998620 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=56.1 th1: temp=55.5 th2: temp=62.7 th3: temp=60.0 sysload=0.20 cputime=500.388 memavail=7395324 print_time=6621.389 buffer_time=2.245 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 55 Hz
Stats 6597.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30812758 bytes_read=4803925 bytes_retransmit=9 bytes_invalid=0 send_seq=582464 receive_seq=582464 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=1894 freq=400016047 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40852 bytes_read=127799 bytes_retransmit=0 bytes_invalid=0 send_seq=6780 receive_seq=6780 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999490 adj=49997478 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=197117 bytes_read=6289851 bytes_retransmit=9 bytes_invalid=0 send_seq=27477 receive_seq=27477 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997593 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136284 bytes_read=3719956 bytes_retransmit=9 bytes_invalid=0 send_seq=18881 receive_seq=18881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41119 bytes_read=1684527 bytes_retransmit=9 bytes_invalid=0 send_seq=6794 receive_seq=6794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41605 bytes_read=125294 bytes_retransmit=9 bytes_invalid=0 send_seq=6781 receive_seq=6781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95697 bytes_read=2574770 bytes_retransmit=0 bytes_invalid=0 send_seq=11340 receive_seq=11340 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998643 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=56.1 th1: temp=55.4 th2: temp=62.4 th3: temp=59.9 sysload=0.20 cputime=500.564 memavail=7393892 print_time=6622.291 buffer_time=2.146 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6598.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30818286 bytes_read=4804750 bytes_retransmit=9 bytes_invalid=0 send_seq=582567 receive_seq=582567 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=781 freq=400016047 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40858 bytes_read=127828 bytes_retransmit=0 bytes_invalid=0 send_seq=6781 receive_seq=6781 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999491 adj=49997484 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=197193 bytes_read=6292908 bytes_retransmit=9 bytes_invalid=0 send_seq=27488 receive_seq=27488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997579 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136290 bytes_read=3720056 bytes_retransmit=9 bytes_invalid=0 send_seq=18882 receive_seq=18882 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997497 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41125 bytes_read=1684799 bytes_retransmit=9 bytes_invalid=0 send_seq=6795 receive_seq=6795 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41611 bytes_read=125310 bytes_retransmit=9 bytes_invalid=0 send_seq=6782 receive_seq=6782 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95703 bytes_read=2575126 bytes_retransmit=0 bytes_invalid=0 send_seq=11341 receive_seq=11341 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998648 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=56.1 th1: temp=55.5 th2: temp=62.5 th3: temp=59.9 sysload=0.20 cputime=500.665 memavail=7393892 print_time=6623.209 buffer_time=2.064 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 56 Hz
Testing frequency 57 Hz
Stats 6599.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30823851 bytes_read=4805580 bytes_retransmit=9 bytes_invalid=0 send_seq=582671 receive_seq=582671 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=26 upcoming_bytes=1596 freq=400016043 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40864 bytes_read=127844 bytes_retransmit=0 bytes_invalid=0 send_seq=6782 receive_seq=6782 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999490 adj=49997493 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=197269 bytes_read=6295965 bytes_retransmit=9 bytes_invalid=0 send_seq=27499 receive_seq=27499 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997558 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136296 bytes_read=3720156 bytes_retransmit=9 bytes_invalid=0 send_seq=18883 receive_seq=18883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997594 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41131 bytes_read=1685032 bytes_retransmit=9 bytes_invalid=0 send_seq=6796 receive_seq=6796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997712 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41617 bytes_read=125326 bytes_retransmit=9 bytes_invalid=0 send_seq=6783 receive_seq=6783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95709 bytes_read=2575482 bytes_retransmit=0 bytes_invalid=0 send_seq=11342 receive_seq=11342 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998649 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=56.3 th1: temp=55.4 th2: temp=62.5 th3: temp=60.0 sysload=0.20 cputime=500.787 memavail=7394008 print_time=6624.415 buffer_time=2.270 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 58 Hz
Stats 6600.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30828500 bytes_read=4806339 bytes_retransmit=9 bytes_invalid=0 send_seq=582755 receive_seq=582755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=2401 freq=400016045 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40870 bytes_read=127860 bytes_retransmit=0 bytes_invalid=0 send_seq=6783 receive_seq=6783 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999488 adj=49997484 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=197345 bytes_read=6299108 bytes_retransmit=9 bytes_invalid=0 send_seq=27510 receive_seq=27510 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997586 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136302 bytes_read=3720298 bytes_retransmit=9 bytes_invalid=0 send_seq=18884 receive_seq=18884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997558 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41137 bytes_read=1685250 bytes_retransmit=9 bytes_invalid=0 send_seq=6797 receive_seq=6797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997690 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41623 bytes_read=125342 bytes_retransmit=9 bytes_invalid=0 send_seq=6784 receive_seq=6784 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95715 bytes_read=2575838 bytes_retransmit=0 bytes_invalid=0 send_seq=11343 receive_seq=11343 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998766 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=56.3 th1: temp=55.5 th2: temp=62.7 th3: temp=59.9 sysload=0.27 cputime=500.887 memavail=7394008 print_time=6625.313 buffer_time=2.167 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 59 Hz
Stats 6601.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30834225 bytes_read=4807179 bytes_retransmit=9 bytes_invalid=0 send_seq=582861 receive_seq=582861 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=1191 freq=400016033 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40876 bytes_read=127876 bytes_retransmit=0 bytes_invalid=0 send_seq=6784 receive_seq=6784 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999487 adj=49997464 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=197421 bytes_read=6302165 bytes_retransmit=9 bytes_invalid=0 send_seq=27521 receive_seq=27521 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997577 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136308 bytes_read=3720398 bytes_retransmit=9 bytes_invalid=0 send_seq=18885 receive_seq=18885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997550 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41143 bytes_read=1685524 bytes_retransmit=9 bytes_invalid=0 send_seq=6798 receive_seq=6798 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41629 bytes_read=125358 bytes_retransmit=9 bytes_invalid=0 send_seq=6785 receive_seq=6785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95721 bytes_read=2576194 bytes_retransmit=0 bytes_invalid=0 send_seq=11344 receive_seq=11344 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998738 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=56.0 th1: temp=55.6 th2: temp=62.6 th3: temp=60.0 sysload=0.27 cputime=500.991 memavail=7394008 print_time=6626.226 buffer_time=2.080 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 60 Hz
Stats 6602.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30840012 bytes_read=4808041 bytes_retransmit=9 bytes_invalid=0 send_seq=582969 receive_seq=582969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=1896 freq=400016020 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40882 bytes_read=127892 bytes_retransmit=0 bytes_invalid=0 send_seq=6785 receive_seq=6785 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999485 adj=49997470 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=197497 bytes_read=6305238 bytes_retransmit=9 bytes_invalid=0 send_seq=27532 receive_seq=27532 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997605 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136314 bytes_read=3720498 bytes_retransmit=9 bytes_invalid=0 send_seq=18886 receive_seq=18886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997549 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41149 bytes_read=1685742 bytes_retransmit=9 bytes_invalid=0 send_seq=6799 receive_seq=6799 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997679 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41635 bytes_read=125385 bytes_retransmit=9 bytes_invalid=0 send_seq=6786 receive_seq=6786 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95727 bytes_read=2576550 bytes_retransmit=0 bytes_invalid=0 send_seq=11345 receive_seq=11345 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998732 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=56.4 th1: temp=55.8 th2: temp=62.6 th3: temp=59.9 sysload=0.27 cputime=501.107 memavail=7394008 print_time=6627.430 buffer_time=2.284 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 61 Hz
Stats 6603.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30844774 bytes_read=4808833 bytes_retransmit=9 bytes_invalid=0 send_seq=583060 receive_seq=583060 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=2627 freq=400016008 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=40888 bytes_read=127921 bytes_retransmit=0 bytes_invalid=0 send_seq=6786 receive_seq=6786 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999485 adj=49997474 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=197573 bytes_read=6308324 bytes_retransmit=9 bytes_invalid=0 send_seq=27543 receive_seq=27543 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997614 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136320 bytes_read=3720626 bytes_retransmit=9 bytes_invalid=0 send_seq=18887 receive_seq=18887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997541 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41155 bytes_read=1685976 bytes_retransmit=9 bytes_invalid=0 send_seq=6800 receive_seq=6800 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41641 bytes_read=125401 bytes_retransmit=9 bytes_invalid=0 send_seq=6787 receive_seq=6787 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95733 bytes_read=2576906 bytes_retransmit=0 bytes_invalid=0 send_seq=11346 receive_seq=11346 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998716 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=56.3 th1: temp=55.5 th2: temp=62.7 th3: temp=60.0 sysload=0.27 cputime=501.212 memavail=7394008 print_time=6628.320 buffer_time=2.174 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 62 Hz
Stats 6604.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30850628 bytes_read=4809678 bytes_retransmit=9 bytes_invalid=0 send_seq=583167 receive_seq=583167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=1472 freq=400016003 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=40894 bytes_read=127937 bytes_retransmit=0 bytes_invalid=0 send_seq=6787 receive_seq=6787 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999484 adj=49997486 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=197649 bytes_read=6311382 bytes_retransmit=9 bytes_invalid=0 send_seq=27554 receive_seq=27554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997674 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136326 bytes_read=3720726 bytes_retransmit=9 bytes_invalid=0 send_seq=18888 receive_seq=18888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997543 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41161 bytes_read=1686285 bytes_retransmit=9 bytes_invalid=0 send_seq=6801 receive_seq=6801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41647 bytes_read=125417 bytes_retransmit=9 bytes_invalid=0 send_seq=6788 receive_seq=6788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95739 bytes_read=2577262 bytes_retransmit=0 bytes_invalid=0 send_seq=11347 receive_seq=11347 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998713 coil_temp=16.9 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.6 th2: temp=62.6 th3: temp=60.0 sysload=0.27 cputime=501.321 memavail=7394008 print_time=6629.238 buffer_time=2.091 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 63 Hz
Stats 6605.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30856553 bytes_read=4810552 bytes_retransmit=9 bytes_invalid=0 send_seq=583277 receive_seq=583277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=2405 freq=400016008 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=40900 bytes_read=127953 bytes_retransmit=0 bytes_invalid=0 send_seq=6788 receive_seq=6788 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999485 adj=49997485 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=197725 bytes_read=6314443 bytes_retransmit=9 bytes_invalid=0 send_seq=27565 receive_seq=27565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997666 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136332 bytes_read=3720840 bytes_retransmit=9 bytes_invalid=0 send_seq=18889 receive_seq=18889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41167 bytes_read=1686519 bytes_retransmit=9 bytes_invalid=0 send_seq=6802 receive_seq=6802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41653 bytes_read=125433 bytes_retransmit=9 bytes_invalid=0 send_seq=6789 receive_seq=6789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95745 bytes_read=2577618 bytes_retransmit=0 bytes_invalid=0 send_seq=11348 receive_seq=11348 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998705 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.4 th2: temp=62.6 th3: temp=60.0 sysload=0.24 cputime=501.438 memavail=7393532 print_time=6630.451 buffer_time=2.304 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 64 Hz
Stats 6606.5: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30861458 bytes_read=4811347 bytes_retransmit=9 bytes_invalid=0 send_seq=583371 receive_seq=583371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=2946 freq=400016005 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=40906 bytes_read=127969 bytes_retransmit=0 bytes_invalid=0 send_seq=6789 receive_seq=6789 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999485 adj=49997488 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=197801 bytes_read=6317527 bytes_retransmit=9 bytes_invalid=0 send_seq=27576 receive_seq=27576 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997724 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136338 bytes_read=3720968 bytes_retransmit=9 bytes_invalid=0 send_seq=18890 receive_seq=18890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997501 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41173 bytes_read=1686753 bytes_retransmit=9 bytes_invalid=0 send_seq=6803 receive_seq=6803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41659 bytes_read=125449 bytes_retransmit=9 bytes_invalid=0 send_seq=6790 receive_seq=6790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95751 bytes_read=2577974 bytes_retransmit=0 bytes_invalid=0 send_seq=11349 receive_seq=11349 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998675 coil_temp=16.9 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.7 th2: temp=62.5 th3: temp=59.9 sysload=0.24 cputime=501.543 memavail=7393548 print_time=6631.319 buffer_time=2.171 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 65 Hz
Stats 6607.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30867533 bytes_read=4812233 bytes_retransmit=9 bytes_invalid=0 send_seq=583483 receive_seq=583483 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=1900 freq=400016014 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=40912 bytes_read=127985 bytes_retransmit=0 bytes_invalid=0 send_seq=6790 receive_seq=6790 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999484 adj=49997486 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=197877 bytes_read=6320662 bytes_retransmit=9 bytes_invalid=0 send_seq=27587 receive_seq=27587 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997742 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136344 bytes_read=3721068 bytes_retransmit=9 bytes_invalid=0 send_seq=18891 receive_seq=18891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997492 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41179 bytes_read=1687047 bytes_retransmit=9 bytes_invalid=0 send_seq=6804 receive_seq=6804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41665 bytes_read=125476 bytes_retransmit=9 bytes_invalid=0 send_seq=6791 receive_seq=6791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95757 bytes_read=2578330 bytes_retransmit=0 bytes_invalid=0 send_seq=11350 receive_seq=11350 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998664 coil_temp=16.9 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.5 th2: temp=62.6 th3: temp=60.1 sysload=0.24 cputime=501.654 memavail=7393280 print_time=6632.254 buffer_time=2.105 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 66 Hz
Stats 6608.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30873543 bytes_read=4813117 bytes_retransmit=9 bytes_invalid=0 send_seq=583595 receive_seq=583595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=2755 freq=400016005 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40918 bytes_read=128014 bytes_retransmit=0 bytes_invalid=0 send_seq=6791 receive_seq=6791 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999483 adj=49997471 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=197953 bytes_read=6323719 bytes_retransmit=9 bytes_invalid=0 send_seq=27598 receive_seq=27598 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997680 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136350 bytes_read=3721168 bytes_retransmit=9 bytes_invalid=0 send_seq=18892 receive_seq=18892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997474 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41185 bytes_read=1687281 bytes_retransmit=9 bytes_invalid=0 send_seq=6805 receive_seq=6805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41671 bytes_read=125492 bytes_retransmit=9 bytes_invalid=0 send_seq=6792 receive_seq=6792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95763 bytes_read=2578686 bytes_retransmit=0 bytes_invalid=0 send_seq=11351 receive_seq=11351 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998649 coil_temp=16.8 refs=0 mcu_temp=20.32 supply_voltage=3.012 th0: temp=56.3 th1: temp=55.6 th2: temp=62.5 th3: temp=60.0 sysload=0.24 cputime=501.769 memavail=7393316 print_time=6633.457 buffer_time=2.307 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 67 Hz
Stats 6609.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30878639 bytes_read=4813902 bytes_retransmit=9 bytes_invalid=0 send_seq=583687 receive_seq=583687 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=47 upcoming_bytes=3248 freq=400016011 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40924 bytes_read=128030 bytes_retransmit=0 bytes_invalid=0 send_seq=6792 receive_seq=6792 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999483 adj=49997474 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=198022 bytes_read=6326781 bytes_retransmit=9 bytes_invalid=0 send_seq=27608 receive_seq=27608 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997664 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136356 bytes_read=3721296 bytes_retransmit=9 bytes_invalid=0 send_seq=18893 receive_seq=18893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997486 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41191 bytes_read=1687530 bytes_retransmit=9 bytes_invalid=0 send_seq=6806 receive_seq=6806 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41677 bytes_read=125508 bytes_retransmit=9 bytes_invalid=0 send_seq=6793 receive_seq=6793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95769 bytes_read=2579042 bytes_retransmit=0 bytes_invalid=0 send_seq=11352 receive_seq=11352 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998659 coil_temp=16.8 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=56.1 th1: temp=55.5 th2: temp=62.5 th3: temp=60.1 sysload=0.24 cputime=501.874 memavail=7393316 print_time=6634.337 buffer_time=2.186 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 68 Hz
Stats 6610.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30884832 bytes_read=4814792 bytes_retransmit=9 bytes_invalid=0 send_seq=583803 receive_seq=583803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=2256 freq=400016015 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40930 bytes_read=128046 bytes_retransmit=0 bytes_invalid=0 send_seq=6793 receive_seq=6793 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999483 adj=49997462 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=198098 bytes_read=6329838 bytes_retransmit=9 bytes_invalid=0 send_seq=27619 receive_seq=27619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997666 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136362 bytes_read=3721410 bytes_retransmit=9 bytes_invalid=0 send_seq=18894 receive_seq=18894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997560 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41197 bytes_read=1687824 bytes_retransmit=9 bytes_invalid=0 send_seq=6807 receive_seq=6807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41683 bytes_read=125524 bytes_retransmit=9 bytes_invalid=0 send_seq=6794 receive_seq=6794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95775 bytes_read=2579398 bytes_retransmit=0 bytes_invalid=0 send_seq=11353 receive_seq=11353 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998645 coil_temp=16.8 refs=0 mcu_temp=20.31 supply_voltage=3.012 th0: temp=56.3 th1: temp=55.6 th2: temp=62.7 th3: temp=60.1 sysload=0.22 cputime=501.985 memavail=7393316 print_time=6635.265 buffer_time=2.114 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 69 Hz
Stats 6611.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30891066 bytes_read=4815711 bytes_retransmit=9 bytes_invalid=0 send_seq=583919 receive_seq=583919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=3073 freq=400016013 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40936 bytes_read=128062 bytes_retransmit=0 bytes_invalid=0 send_seq=6794 receive_seq=6794 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999482 adj=49997459 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=198174 bytes_read=6332896 bytes_retransmit=9 bytes_invalid=0 send_seq=27630 receive_seq=27630 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997637 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136368 bytes_read=3721510 bytes_retransmit=9 bytes_invalid=0 send_seq=18895 receive_seq=18895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997544 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41203 bytes_read=1688058 bytes_retransmit=9 bytes_invalid=0 send_seq=6808 receive_seq=6808 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41689 bytes_read=125540 bytes_retransmit=9 bytes_invalid=0 send_seq=6795 receive_seq=6795 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95781 bytes_read=2579754 bytes_retransmit=0 bytes_invalid=0 send_seq=11354 receive_seq=11354 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998651 coil_temp=16.8 refs=0 mcu_temp=20.30 supply_voltage=3.012 th0: temp=56.3 th1: temp=55.5 th2: temp=62.6 th3: temp=60.0 sysload=0.22 cputime=502.104 memavail=7393316 print_time=6636.463 buffer_time=2.304 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 70 Hz
Stats 6612.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30896395 bytes_read=4816537 bytes_retransmit=9 bytes_invalid=0 send_seq=584019 receive_seq=584019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=3584 freq=400015996 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40942 bytes_read=128078 bytes_retransmit=0 bytes_invalid=0 send_seq=6795 receive_seq=6795 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999482 adj=49997461 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=198250 bytes_read=6336057 bytes_retransmit=9 bytes_invalid=0 send_seq=27641 receive_seq=27641 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997621 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136374 bytes_read=3721638 bytes_retransmit=9 bytes_invalid=0 send_seq=18896 receive_seq=18896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997517 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41209 bytes_read=1688307 bytes_retransmit=9 bytes_invalid=0 send_seq=6809 receive_seq=6809 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41695 bytes_read=125567 bytes_retransmit=9 bytes_invalid=0 send_seq=6796 receive_seq=6796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95787 bytes_read=2580110 bytes_retransmit=0 bytes_invalid=0 send_seq=11355 receive_seq=11355 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998695 coil_temp=16.8 refs=0 mcu_temp=20.29 supply_voltage=3.012 th0: temp=56.2 th1: temp=55.7 th2: temp=62.7 th3: temp=60.1 sysload=0.22 cputime=502.212 memavail=7393316 print_time=6637.353 buffer_time=2.193 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 71 Hz
Stats 6613.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30902614 bytes_read=4817407 bytes_retransmit=9 bytes_invalid=0 send_seq=584132 receive_seq=584132 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=2552 freq=400015988 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40948 bytes_read=128107 bytes_retransmit=0 bytes_invalid=0 send_seq=6796 receive_seq=6796 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999483 adj=49997482 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=198326 bytes_read=6339113 bytes_retransmit=9 bytes_invalid=0 send_seq=27652 receive_seq=27652 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997714 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136380 bytes_read=3721738 bytes_retransmit=9 bytes_invalid=0 send_seq=18897 receive_seq=18897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41215 bytes_read=1688586 bytes_retransmit=9 bytes_invalid=0 send_seq=6810 receive_seq=6810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999566 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41701 bytes_read=125583 bytes_retransmit=9 bytes_invalid=0 send_seq=6797 receive_seq=6797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95793 bytes_read=2580466 bytes_retransmit=0 bytes_invalid=0 send_seq=11356 receive_seq=11356 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998701 coil_temp=16.8 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=56.4 th1: temp=55.5 th2: temp=62.6 th3: temp=60.0 sysload=0.22 cputime=502.323 memavail=7393316 print_time=6638.267 buffer_time=2.106 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 6614.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30909118 bytes_read=4818336 bytes_retransmit=9 bytes_invalid=0 send_seq=584250 receive_seq=584250 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=2050 freq=400015996 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40954 bytes_read=128123 bytes_retransmit=0 bytes_invalid=0 send_seq=6797 receive_seq=6797 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999485 adj=49997514 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=198402 bytes_read=6342170 bytes_retransmit=9 bytes_invalid=0 send_seq=27663 receive_seq=27663 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997800 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136386 bytes_read=3721838 bytes_retransmit=9 bytes_invalid=0 send_seq=18898 receive_seq=18898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41221 bytes_read=1688835 bytes_retransmit=9 bytes_invalid=0 send_seq=6811 receive_seq=6811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999569 adj=47997740 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41707 bytes_read=125599 bytes_retransmit=9 bytes_invalid=0 send_seq=6798 receive_seq=6798 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95799 bytes_read=2580822 bytes_retransmit=0 bytes_invalid=0 send_seq=11357 receive_seq=11357 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998693 coil_temp=16.8 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=56.4 th1: temp=55.7 th2: temp=62.5 th3: temp=60.1 sysload=0.22 cputime=502.431 memavail=7393316 print_time=6639.162 buffer_time=2.001 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Testing frequency 72 Hz
Testing frequency 73 Hz
Stats 6615.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30914526 bytes_read=4819161 bytes_retransmit=9 bytes_invalid=0 send_seq=584353 receive_seq=584353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=3894 freq=400015997 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40960 bytes_read=128139 bytes_retransmit=0 bytes_invalid=0 send_seq=6798 receive_seq=6798 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999484 adj=49997516 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=198478 bytes_read=6345255 bytes_retransmit=9 bytes_invalid=0 send_seq=27674 receive_seq=27674 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997732 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136392 bytes_read=3721980 bytes_retransmit=9 bytes_invalid=0 send_seq=18899 receive_seq=18899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41227 bytes_read=1689084 bytes_retransmit=9 bytes_invalid=0 send_seq=6812 receive_seq=6812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999568 adj=47997761 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41713 bytes_read=125615 bytes_retransmit=9 bytes_invalid=0 send_seq=6799 receive_seq=6799 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95805 bytes_read=2581178 bytes_retransmit=0 bytes_invalid=0 send_seq=11358 receive_seq=11358 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998729 coil_temp=16.8 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=56.1 th1: temp=55.5 th2: temp=62.7 th3: temp=60.0 sysload=0.21 cputime=502.546 memavail=7393328 print_time=6640.364 buffer_time=2.203 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 74 Hz
Stats 6616.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30920913 bytes_read=4820061 bytes_retransmit=9 bytes_invalid=0 send_seq=584471 receive_seq=584471 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=3146 freq=400015991 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40966 bytes_read=128155 bytes_retransmit=0 bytes_invalid=0 send_seq=6799 receive_seq=6799 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999483 adj=49997497 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=198554 bytes_read=6348311 bytes_retransmit=9 bytes_invalid=0 send_seq=27685 receive_seq=27685 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000243 adj=63997790 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136398 bytes_read=3722080 bytes_retransmit=9 bytes_invalid=0 send_seq=18900 receive_seq=18900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41233 bytes_read=1689363 bytes_retransmit=9 bytes_invalid=0 send_seq=6813 receive_seq=6813 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999567 adj=47997715 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41719 bytes_read=125631 bytes_retransmit=9 bytes_invalid=0 send_seq=6800 receive_seq=6800 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95811 bytes_read=2581534 bytes_retransmit=0 bytes_invalid=0 send_seq=11359 receive_seq=11359 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998694 coil_temp=16.8 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=56.1 th1: temp=55.4 th2: temp=62.5 th3: temp=60.0 sysload=0.21 cputime=502.662 memavail=7387808 print_time=6641.292 buffer_time=2.130 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6617.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30927503 bytes_read=4821021 bytes_retransmit=9 bytes_invalid=0 send_seq=584592 receive_seq=584592 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=2434 freq=400016020 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=40972 bytes_read=128171 bytes_retransmit=0 bytes_invalid=0 send_seq=6800 receive_seq=6800 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999483 adj=49997495 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=198630 bytes_read=6351385 bytes_retransmit=9 bytes_invalid=0 send_seq=27696 receive_seq=27696 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997850 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136404 bytes_read=3722180 bytes_retransmit=9 bytes_invalid=0 send_seq=18901 receive_seq=18901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41239 bytes_read=1689597 bytes_retransmit=9 bytes_invalid=0 send_seq=6814 receive_seq=6814 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999567 adj=47997701 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41725 bytes_read=125658 bytes_retransmit=9 bytes_invalid=0 send_seq=6801 receive_seq=6801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95817 bytes_read=2581890 bytes_retransmit=0 bytes_invalid=0 send_seq=11360 receive_seq=11360 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998709 coil_temp=16.8 refs=0 mcu_temp=20.25 supply_voltage=3.012 th0: temp=56.3 th1: temp=55.5 th2: temp=62.8 th3: temp=60.1 sysload=0.21 cputime=502.775 memavail=7393208 print_time=6642.177 buffer_time=2.015 print_stall=0 extruder: target=0 temp=19.2 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 75 Hz
Testing frequency 76 Hz
Stats 6618.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30933096 bytes_read=4821851 bytes_retransmit=9 bytes_invalid=0 send_seq=584696 receive_seq=584696 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=4242 freq=400016028 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40978 bytes_read=128200 bytes_retransmit=0 bytes_invalid=0 send_seq=6801 receive_seq=6801 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999483 adj=49997438 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=198706 bytes_read=6354470 bytes_retransmit=9 bytes_invalid=0 send_seq=27707 receive_seq=27707 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997726 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136410 bytes_read=3722308 bytes_retransmit=9 bytes_invalid=0 send_seq=18902 receive_seq=18902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997459 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41245 bytes_read=1689846 bytes_retransmit=9 bytes_invalid=0 send_seq=6815 receive_seq=6815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999567 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41731 bytes_read=125674 bytes_retransmit=9 bytes_invalid=0 send_seq=6802 receive_seq=6802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95823 bytes_read=2582246 bytes_retransmit=0 bytes_invalid=0 send_seq=11361 receive_seq=11361 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998665 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=56.3 th1: temp=55.5 th2: temp=62.7 th3: temp=60.0 sysload=0.21 cputime=502.892 memavail=7394464 print_time=6643.372 buffer_time=2.209 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 77 Hz
Stats 6619.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30939695 bytes_read=4822756 bytes_retransmit=9 bytes_invalid=0 send_seq=584815 receive_seq=584815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=3706 freq=400016048 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40984 bytes_read=128216 bytes_retransmit=0 bytes_invalid=0 send_seq=6802 receive_seq=6802 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999481 adj=49997439 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=198782 bytes_read=6357529 bytes_retransmit=9 bytes_invalid=0 send_seq=27718 receive_seq=27718 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997656 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136416 bytes_read=3722408 bytes_retransmit=9 bytes_invalid=0 send_seq=18903 receive_seq=18903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997451 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41251 bytes_read=1690140 bytes_retransmit=9 bytes_invalid=0 send_seq=6816 receive_seq=6816 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999567 adj=47997634 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41737 bytes_read=125690 bytes_retransmit=9 bytes_invalid=0 send_seq=6803 receive_seq=6803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95829 bytes_read=2582602 bytes_retransmit=0 bytes_invalid=0 send_seq=11362 receive_seq=11362 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998645 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=56.3 th1: temp=55.6 th2: temp=62.7 th3: temp=60.1 sysload=0.21 cputime=503.003 memavail=7394244 print_time=6644.311 buffer_time=2.148 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6620.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30946430 bytes_read=4823710 bytes_retransmit=9 bytes_invalid=0 send_seq=584938 receive_seq=584938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=2712 freq=400016078 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40990 bytes_read=128232 bytes_retransmit=0 bytes_invalid=0 send_seq=6803 receive_seq=6803 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999480 adj=49997399 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=198858 bytes_read=6360632 bytes_retransmit=9 bytes_invalid=0 send_seq=27729 receive_seq=27729 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997590 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136422 bytes_read=3722516 bytes_retransmit=9 bytes_invalid=0 send_seq=18904 receive_seq=18904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997409 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41257 bytes_read=1690374 bytes_retransmit=9 bytes_invalid=0 send_seq=6817 receive_seq=6817 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999566 adj=47997605 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41743 bytes_read=125706 bytes_retransmit=9 bytes_invalid=0 send_seq=6804 receive_seq=6804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95835 bytes_read=2582958 bytes_retransmit=0 bytes_invalid=0 send_seq=11363 receive_seq=11363 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998631 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.012 th0: temp=56.3 th1: temp=55.6 th2: temp=62.8 th3: temp=60.2 sysload=0.19 cputime=503.113 memavail=7394244 print_time=6645.179 buffer_time=2.015 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 78 Hz
Testing frequency 79 Hz
Stats 6621.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30952115 bytes_read=4824555 bytes_retransmit=9 bytes_invalid=0 send_seq=585045 receive_seq=585045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=4593 freq=400016070 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=40996 bytes_read=128248 bytes_retransmit=0 bytes_invalid=0 send_seq=6804 receive_seq=6804 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999481 adj=49997339 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=198934 bytes_read=6363696 bytes_retransmit=9 bytes_invalid=0 send_seq=27740 receive_seq=27740 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997497 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136428 bytes_read=3722635 bytes_retransmit=9 bytes_invalid=0 send_seq=18905 receive_seq=18905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997352 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41263 bytes_read=1690623 bytes_retransmit=9 bytes_invalid=0 send_seq=6818 receive_seq=6818 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999566 adj=47997552 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41749 bytes_read=125722 bytes_retransmit=9 bytes_invalid=0 send_seq=6805 receive_seq=6805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95841 bytes_read=2583314 bytes_retransmit=0 bytes_invalid=0 send_seq=11364 receive_seq=11364 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998587 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.5 th2: temp=62.7 th3: temp=60.1 sysload=0.19 cputime=503.233 memavail=7394260 print_time=6646.388 buffer_time=2.223 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 80 Hz
Stats 6622.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30958897 bytes_read=4825486 bytes_retransmit=9 bytes_invalid=0 send_seq=585166 receive_seq=585166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=4029 freq=400016251 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41002 bytes_read=128264 bytes_retransmit=0 bytes_invalid=0 send_seq=6805 receive_seq=6805 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999480 adj=49997404 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=199010 bytes_read=6366753 bytes_retransmit=9 bytes_invalid=0 send_seq=27751 receive_seq=27751 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997545 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136434 bytes_read=3722728 bytes_retransmit=9 bytes_invalid=0 send_seq=18906 receive_seq=18906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997397 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41269 bytes_read=1690902 bytes_retransmit=9 bytes_invalid=0 send_seq=6819 receive_seq=6819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999566 adj=47997590 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41755 bytes_read=125749 bytes_retransmit=9 bytes_invalid=0 send_seq=6806 receive_seq=6806 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95847 bytes_read=2583670 bytes_retransmit=0 bytes_invalid=0 send_seq=11365 receive_seq=11365 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998610 coil_temp=16.8 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.7 th2: temp=62.6 th3: temp=60.2 sysload=0.19 cputime=503.347 memavail=7394260 print_time=6647.320 buffer_time=2.155 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6623.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30965752 bytes_read=4826453 bytes_retransmit=9 bytes_invalid=0 send_seq=585292 receive_seq=585292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=46 upcoming_bytes=2923 freq=400016223 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41008 bytes_read=128292 bytes_retransmit=0 bytes_invalid=0 send_seq=6806 receive_seq=6806 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999480 adj=49997123 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=199086 bytes_read=6369795 bytes_retransmit=9 bytes_invalid=0 send_seq=27762 receive_seq=27762 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997277 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136440 bytes_read=3722821 bytes_retransmit=9 bytes_invalid=0 send_seq=18907 receive_seq=18907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997040 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41275 bytes_read=1691136 bytes_retransmit=9 bytes_invalid=0 send_seq=6820 receive_seq=6820 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999565 adj=47997327 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41761 bytes_read=125765 bytes_retransmit=9 bytes_invalid=0 send_seq=6807 receive_seq=6807 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999369 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95853 bytes_read=2584026 bytes_retransmit=0 bytes_invalid=0 send_seq=11366 receive_seq=11366 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998428 coil_temp=16.8 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.6 th2: temp=62.6 th3: temp=60.1 sysload=0.19 cputime=503.457 memavail=7394260 print_time=6648.189 buffer_time=2.024 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 81 Hz
Testing frequency 82 Hz
Stats 6624.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30971570 bytes_read=4827305 bytes_retransmit=9 bytes_invalid=0 send_seq=585401 receive_seq=585401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=4872 freq=400016219 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41014 bytes_read=128307 bytes_retransmit=0 bytes_invalid=0 send_seq=6807 receive_seq=6807 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999478 adj=49997197 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=199162 bytes_read=6372872 bytes_retransmit=9 bytes_invalid=0 send_seq=27773 receive_seq=27773 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997334 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136446 bytes_read=3722946 bytes_retransmit=9 bytes_invalid=0 send_seq=18908 receive_seq=18908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997131 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41281 bytes_read=1691400 bytes_retransmit=9 bytes_invalid=0 send_seq=6821 receive_seq=6821 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997388 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41767 bytes_read=125781 bytes_retransmit=9 bytes_invalid=0 send_seq=6808 receive_seq=6808 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999383 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95859 bytes_read=2584382 bytes_retransmit=0 bytes_invalid=0 send_seq=11367 receive_seq=11367 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998468 coil_temp=16.8 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.6 th2: temp=62.7 th3: temp=60.1 sysload=0.19 cputime=503.579 memavail=7394260 print_time=6649.390 buffer_time=2.224 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 83 Hz
Stats 6625.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30978523 bytes_read=4828250 bytes_retransmit=9 bytes_invalid=0 send_seq=585528 receive_seq=585528 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=4384 freq=400016202 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41020 bytes_read=128322 bytes_retransmit=0 bytes_invalid=0 send_seq=6808 receive_seq=6808 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999479 adj=49997263 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=199231 bytes_read=6375907 bytes_retransmit=9 bytes_invalid=0 send_seq=27783 receive_seq=27783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997410 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136452 bytes_read=3723060 bytes_retransmit=9 bytes_invalid=0 send_seq=18909 receive_seq=18909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997254 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41287 bytes_read=1691679 bytes_retransmit=9 bytes_invalid=0 send_seq=6822 receive_seq=6822 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997451 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41773 bytes_read=125797 bytes_retransmit=9 bytes_invalid=0 send_seq=6809 receive_seq=6809 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999397 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95865 bytes_read=2584738 bytes_retransmit=0 bytes_invalid=0 send_seq=11368 receive_seq=11368 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998516 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.5 th2: temp=63.0 th3: temp=60.1 sysload=0.17 cputime=503.693 memavail=7394260 print_time=6650.334 buffer_time=2.167 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 84 Hz
Stats 6626.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=30985529 bytes_read=4829229 bytes_retransmit=9 bytes_invalid=0 send_seq=585656 receive_seq=585656 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=3053 freq=400016181 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41026 bytes_read=128337 bytes_retransmit=0 bytes_invalid=0 send_seq=6809 receive_seq=6809 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999477 adj=49997322 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=199307 bytes_read=6378963 bytes_retransmit=9 bytes_invalid=0 send_seq=27794 receive_seq=27794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997447 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136458 bytes_read=3723160 bytes_retransmit=9 bytes_invalid=0 send_seq=18910 receive_seq=18910 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997312 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41293 bytes_read=1691913 bytes_retransmit=9 bytes_invalid=0 send_seq=6823 receive_seq=6823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997493 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41779 bytes_read=125813 bytes_retransmit=9 bytes_invalid=0 send_seq=6810 receive_seq=6810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999408 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95871 bytes_read=2585094 bytes_retransmit=0 bytes_invalid=0 send_seq=11369 receive_seq=11369 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998540 coil_temp=16.8 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.6 th2: temp=62.7 th3: temp=60.1 sysload=0.17 cputime=503.810 memavail=7394260 print_time=6651.202 buffer_time=2.034 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 85 Hz
Stats 6627.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30991374 bytes_read=4830100 bytes_retransmit=9 bytes_invalid=0 send_seq=585765 receive_seq=585765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=5045 freq=400016165 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41032 bytes_read=128352 bytes_retransmit=0 bytes_invalid=0 send_seq=6810 receive_seq=6810 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999477 adj=49997355 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=199383 bytes_read=6382124 bytes_retransmit=9 bytes_invalid=0 send_seq=27805 receive_seq=27805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997475 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136464 bytes_read=3723288 bytes_retransmit=9 bytes_invalid=0 send_seq=18911 receive_seq=18911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997381 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41299 bytes_read=1692177 bytes_retransmit=9 bytes_invalid=0 send_seq=6824 receive_seq=6824 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997540 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41785 bytes_read=125840 bytes_retransmit=9 bytes_invalid=0 send_seq=6811 receive_seq=6811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999415 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95877 bytes_read=2585450 bytes_retransmit=0 bytes_invalid=0 send_seq=11370 receive_seq=11370 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998564 coil_temp=16.8 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.7 th2: temp=62.6 th3: temp=60.1 sysload=0.17 cputime=503.935 memavail=7392272 print_time=6652.393 buffer_time=2.224 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 86 Hz
Stats 6628.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=30998286 bytes_read=4831045 bytes_retransmit=9 bytes_invalid=0 send_seq=585892 receive_seq=585892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=4902 freq=400016157 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41038 bytes_read=128381 bytes_retransmit=0 bytes_invalid=0 send_seq=6811 receive_seq=6811 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999478 adj=49997407 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=199459 bytes_read=6385181 bytes_retransmit=9 bytes_invalid=0 send_seq=27816 receive_seq=27816 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997537 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136470 bytes_read=3723388 bytes_retransmit=9 bytes_invalid=0 send_seq=18912 receive_seq=18912 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997424 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41305 bytes_read=1692441 bytes_retransmit=9 bytes_invalid=0 send_seq=6825 receive_seq=6825 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997594 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41791 bytes_read=125856 bytes_retransmit=9 bytes_invalid=0 send_seq=6812 receive_seq=6812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95883 bytes_read=2585806 bytes_retransmit=0 bytes_invalid=0 send_seq=11371 receive_seq=11371 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998599 coil_temp=16.8 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.7 th2: temp=62.6 th3: temp=60.1 sysload=0.17 cputime=504.050 memavail=7392272 print_time=6653.345 buffer_time=2.175 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 87 Hz
Stats 6629.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31005560 bytes_read=4832039 bytes_retransmit=9 bytes_invalid=0 send_seq=586023 receive_seq=586023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=3406 freq=400016157 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41044 bytes_read=128397 bytes_retransmit=0 bytes_invalid=0 send_seq=6812 receive_seq=6812 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999478 adj=49997435 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=199535 bytes_read=6388239 bytes_retransmit=9 bytes_invalid=0 send_seq=27827 receive_seq=27827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997537 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136476 bytes_read=3723488 bytes_retransmit=9 bytes_invalid=0 send_seq=18913 receive_seq=18913 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997438 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41311 bytes_read=1692690 bytes_retransmit=9 bytes_invalid=0 send_seq=6826 receive_seq=6826 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997599 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41797 bytes_read=125872 bytes_retransmit=9 bytes_invalid=0 send_seq=6813 receive_seq=6813 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95889 bytes_read=2586162 bytes_retransmit=0 bytes_invalid=0 send_seq=11372 receive_seq=11372 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998612 coil_temp=16.8 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.8 th2: temp=62.7 th3: temp=60.0 sysload=0.17 cputime=504.166 memavail=7392272 print_time=6654.208 buffer_time=2.038 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 88 Hz
Stats 6630.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31011616 bytes_read=4832919 bytes_retransmit=9 bytes_invalid=0 send_seq=586137 receive_seq=586137 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=5289 freq=400016139 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41050 bytes_read=128413 bytes_retransmit=0 bytes_invalid=0 send_seq=6813 receive_seq=6813 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999477 adj=49997435 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=199611 bytes_read=6391324 bytes_retransmit=9 bytes_invalid=0 send_seq=27838 receive_seq=27838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997523 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136482 bytes_read=3723630 bytes_retransmit=9 bytes_invalid=0 send_seq=18914 receive_seq=18914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997429 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41317 bytes_read=1692954 bytes_retransmit=9 bytes_invalid=0 send_seq=6827 receive_seq=6827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997594 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41803 bytes_read=125888 bytes_retransmit=9 bytes_invalid=0 send_seq=6814 receive_seq=6814 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95895 bytes_read=2586518 bytes_retransmit=0 bytes_invalid=0 send_seq=11373 receive_seq=11373 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998607 coil_temp=16.8 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.7 th2: temp=62.6 th3: temp=60.3 sysload=0.16 cputime=504.290 memavail=7392272 print_time=6655.398 buffer_time=2.228 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 89 Hz
Stats 6631.5: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31018738 bytes_read=4833879 bytes_retransmit=9 bytes_invalid=0 send_seq=586267 receive_seq=586267 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=4896 freq=400016127 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41056 bytes_read=128429 bytes_retransmit=0 bytes_invalid=0 send_seq=6814 receive_seq=6814 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999477 adj=49997462 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=199687 bytes_read=6394381 bytes_retransmit=9 bytes_invalid=0 send_seq=27849 receive_seq=27849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997566 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136488 bytes_read=3723730 bytes_retransmit=9 bytes_invalid=0 send_seq=18915 receive_seq=18915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997491 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41323 bytes_read=1693218 bytes_retransmit=9 bytes_invalid=0 send_seq=6828 receive_seq=6828 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41809 bytes_read=125904 bytes_retransmit=9 bytes_invalid=0 send_seq=6815 receive_seq=6815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95901 bytes_read=2586874 bytes_retransmit=0 bytes_invalid=0 send_seq=11374 receive_seq=11374 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998637 coil_temp=16.8 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.4 th2: temp=62.8 th3: temp=60.1 sysload=0.16 cputime=504.405 memavail=7392272 print_time=6656.343 buffer_time=2.171 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 90 Hz
Stats 6632.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=31025968 bytes_read=4834869 bytes_retransmit=9 bytes_invalid=0 send_seq=586394 receive_seq=586394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=3478 freq=400016117 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41062 bytes_read=128445 bytes_retransmit=0 bytes_invalid=0 send_seq=6815 receive_seq=6815 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999476 adj=49997476 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=199763 bytes_read=6397454 bytes_retransmit=9 bytes_invalid=0 send_seq=27860 receive_seq=27860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997583 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136494 bytes_read=3723830 bytes_retransmit=9 bytes_invalid=0 send_seq=18916 receive_seq=18916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41329 bytes_read=1693452 bytes_retransmit=9 bytes_invalid=0 send_seq=6829 receive_seq=6829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997631 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41815 bytes_read=125931 bytes_retransmit=9 bytes_invalid=0 send_seq=6816 receive_seq=6816 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95907 bytes_read=2587230 bytes_retransmit=0 bytes_invalid=0 send_seq=11375 receive_seq=11375 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998640 coil_temp=16.8 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.7 th2: temp=62.8 th3: temp=60.0 sysload=0.16 cputime=504.520 memavail=7392280 print_time=6657.217 buffer_time=2.045 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 91 Hz
Stats 6633.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=31031975 bytes_read=4835739 bytes_retransmit=9 bytes_invalid=0 send_seq=586506 receive_seq=586506 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=5496 freq=400016130 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41068 bytes_read=128474 bytes_retransmit=0 bytes_invalid=0 send_seq=6816 receive_seq=6816 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999475 adj=49997480 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=199839 bytes_read=6400538 bytes_retransmit=9 bytes_invalid=0 send_seq=27871 receive_seq=27871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997602 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136500 bytes_read=3723958 bytes_retransmit=9 bytes_invalid=0 send_seq=18917 receive_seq=18917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41335 bytes_read=1693716 bytes_retransmit=9 bytes_invalid=0 send_seq=6830 receive_seq=6830 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41821 bytes_read=125947 bytes_retransmit=9 bytes_invalid=0 send_seq=6817 receive_seq=6817 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95913 bytes_read=2587586 bytes_retransmit=0 bytes_invalid=0 send_seq=11376 receive_seq=11376 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998642 coil_temp=16.8 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.6 th2: temp=62.7 th3: temp=60.2 sysload=0.16 cputime=504.653 memavail=7388752 print_time=6658.417 buffer_time=2.245 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 92 Hz
Stats 6634.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=31039227 bytes_read=4836712 bytes_retransmit=9 bytes_invalid=0 send_seq=586639 receive_seq=586639 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=5286 freq=400016107 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41074 bytes_read=128490 bytes_retransmit=0 bytes_invalid=0 send_seq=6817 receive_seq=6817 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999476 adj=49997444 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=199915 bytes_read=6403655 bytes_retransmit=9 bytes_invalid=0 send_seq=27882 receive_seq=27882 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997590 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136506 bytes_read=3724058 bytes_retransmit=9 bytes_invalid=0 send_seq=18918 receive_seq=18918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997485 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41341 bytes_read=1693995 bytes_retransmit=9 bytes_invalid=0 send_seq=6831 receive_seq=6831 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997609 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41827 bytes_read=125963 bytes_retransmit=9 bytes_invalid=0 send_seq=6818 receive_seq=6818 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95919 bytes_read=2587942 bytes_retransmit=0 bytes_invalid=0 send_seq=11377 receive_seq=11377 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998622 coil_temp=16.8 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.8 th2: temp=62.6 th3: temp=60.0 sysload=0.16 cputime=504.777 memavail=7393176 print_time=6659.358 buffer_time=2.185 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 93 Hz
Stats 6635.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=31046643 bytes_read=4837723 bytes_retransmit=9 bytes_invalid=0 send_seq=586774 receive_seq=586774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=3608 freq=400016108 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41080 bytes_read=128506 bytes_retransmit=0 bytes_invalid=0 send_seq=6818 receive_seq=6818 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999475 adj=49997515 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=199991 bytes_read=6406711 bytes_retransmit=9 bytes_invalid=0 send_seq=27893 receive_seq=27893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997647 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136512 bytes_read=3724172 bytes_retransmit=9 bytes_invalid=0 send_seq=18919 receive_seq=18919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997549 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41347 bytes_read=1694229 bytes_retransmit=9 bytes_invalid=0 send_seq=6832 receive_seq=6832 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41833 bytes_read=125979 bytes_retransmit=9 bytes_invalid=0 send_seq=6819 receive_seq=6819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95925 bytes_read=2588282 bytes_retransmit=0 bytes_invalid=0 send_seq=11378 receive_seq=11378 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998660 coil_temp=16.8 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.6 th2: temp=62.8 th3: temp=60.2 sysload=0.15 cputime=504.892 memavail=7393176 print_time=6660.222 buffer_time=2.049 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 94 Hz
Stats 6636.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=31052830 bytes_read=4838608 bytes_retransmit=9 bytes_invalid=0 send_seq=586889 receive_seq=586889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=5721 freq=400016081 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41086 bytes_read=128522 bytes_retransmit=0 bytes_invalid=0 send_seq=6819 receive_seq=6819 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999476 adj=49997493 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=200067 bytes_read=6409795 bytes_retransmit=9 bytes_invalid=0 send_seq=27904 receive_seq=27904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997631 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136518 bytes_read=3724300 bytes_retransmit=9 bytes_invalid=0 send_seq=18920 receive_seq=18920 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997630 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41353 bytes_read=1694493 bytes_retransmit=9 bytes_invalid=0 send_seq=6833 receive_seq=6833 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41839 bytes_read=125995 bytes_retransmit=9 bytes_invalid=0 send_seq=6820 receive_seq=6820 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95931 bytes_read=2588638 bytes_retransmit=0 bytes_invalid=0 send_seq=11379 receive_seq=11379 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998656 coil_temp=16.8 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.7 th2: temp=62.6 th3: temp=60.1 sysload=0.15 cputime=505.018 memavail=7393176 print_time=6661.421 buffer_time=2.246 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 95 Hz
Stats 6637.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31059918 bytes_read=4839564 bytes_retransmit=9 bytes_invalid=0 send_seq=587015 receive_seq=587015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=5746 freq=400016068 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41092 bytes_read=128538 bytes_retransmit=0 bytes_invalid=0 send_seq=6820 receive_seq=6820 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999477 adj=49997521 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=200143 bytes_read=6412869 bytes_retransmit=9 bytes_invalid=0 send_seq=27915 receive_seq=27915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997643 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136524 bytes_read=3724400 bytes_retransmit=9 bytes_invalid=0 send_seq=18921 receive_seq=18921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997603 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41359 bytes_read=1694757 bytes_retransmit=9 bytes_invalid=0 send_seq=6834 receive_seq=6834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41845 bytes_read=126022 bytes_retransmit=9 bytes_invalid=0 send_seq=6821 receive_seq=6821 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95937 bytes_read=2588994 bytes_retransmit=0 bytes_invalid=0 send_seq=11380 receive_seq=11380 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998669 coil_temp=16.8 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.6 th2: temp=62.6 th3: temp=60.1 sysload=0.15 cputime=505.136 memavail=7392724 print_time=6662.361 buffer_time=2.185 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 96 Hz
Stats 6638.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31067592 bytes_read=4840598 bytes_retransmit=9 bytes_invalid=0 send_seq=587154 receive_seq=587154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=4044 freq=400016061 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41098 bytes_read=128567 bytes_retransmit=0 bytes_invalid=0 send_seq=6821 receive_seq=6821 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999477 adj=49997544 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=200212 bytes_read=6415902 bytes_retransmit=9 bytes_invalid=0 send_seq=27925 receive_seq=27925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997651 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136530 bytes_read=3724500 bytes_retransmit=9 bytes_invalid=0 send_seq=18922 receive_seq=18922 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997599 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41365 bytes_read=1694991 bytes_retransmit=9 bytes_invalid=0 send_seq=6835 receive_seq=6835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41851 bytes_read=126038 bytes_retransmit=9 bytes_invalid=0 send_seq=6822 receive_seq=6822 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95943 bytes_read=2589350 bytes_retransmit=0 bytes_invalid=0 send_seq=11381 receive_seq=11381 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998674 coil_temp=16.8 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.6 th1: temp=55.8 th2: temp=62.6 th3: temp=60.1 sysload=0.15 cputime=505.252 memavail=7392724 print_time=6663.235 buffer_time=2.058 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 97 Hz
Stats 6639.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31074020 bytes_read=4841514 bytes_retransmit=9 bytes_invalid=0 send_seq=587273 receive_seq=587273 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=6055 freq=400016048 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41110 bytes_read=128599 bytes_retransmit=0 bytes_invalid=0 send_seq=6823 receive_seq=6823 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999475 adj=49997539 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=200294 bytes_read=6419005 bytes_retransmit=9 bytes_invalid=0 send_seq=27937 receive_seq=27937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997672 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136542 bytes_read=3724644 bytes_retransmit=9 bytes_invalid=0 send_seq=18924 receive_seq=18924 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997593 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41377 bytes_read=1695286 bytes_retransmit=9 bytes_invalid=0 send_seq=6837 receive_seq=6837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41863 bytes_read=126070 bytes_retransmit=9 bytes_invalid=0 send_seq=6824 receive_seq=6824 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95955 bytes_read=2589722 bytes_retransmit=0 bytes_invalid=0 send_seq=11383 receive_seq=11383 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998681 coil_temp=16.8 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.7 th2: temp=62.6 th3: temp=60.1 sysload=0.15 cputime=505.382 memavail=7392724 print_time=6664.433 buffer_time=2.255 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 98 Hz
Stats 6640.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31081435 bytes_read=4842499 bytes_retransmit=9 bytes_invalid=0 send_seq=587408 receive_seq=587408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=5934 freq=400016048 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41116 bytes_read=128615 bytes_retransmit=0 bytes_invalid=0 send_seq=6824 receive_seq=6824 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999478 adj=49997522 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=200370 bytes_read=6422062 bytes_retransmit=9 bytes_invalid=0 send_seq=27948 receive_seq=27948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997669 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136548 bytes_read=3724758 bytes_retransmit=9 bytes_invalid=0 send_seq=18925 receive_seq=18925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997559 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41383 bytes_read=1695550 bytes_retransmit=9 bytes_invalid=0 send_seq=6838 receive_seq=6838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997703 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41869 bytes_read=126086 bytes_retransmit=9 bytes_invalid=0 send_seq=6825 receive_seq=6825 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95961 bytes_read=2590078 bytes_retransmit=0 bytes_invalid=0 send_seq=11384 receive_seq=11384 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998677 coil_temp=16.8 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.1 th1: temp=55.8 th2: temp=62.9 th3: temp=60.1 sysload=0.13 cputime=505.503 memavail=7392724 print_time=6665.364 buffer_time=2.186 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 99 Hz
Stats 6641.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31089115 bytes_read=4843533 bytes_retransmit=9 bytes_invalid=0 send_seq=587547 receive_seq=587547 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=4211 freq=400016034 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41122 bytes_read=128631 bytes_retransmit=0 bytes_invalid=0 send_seq=6825 receive_seq=6825 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999477 adj=49997546 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=200446 bytes_read=6425177 bytes_retransmit=9 bytes_invalid=0 send_seq=27959 receive_seq=27959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997652 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136554 bytes_read=3724858 bytes_retransmit=9 bytes_invalid=0 send_seq=18926 receive_seq=18926 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41389 bytes_read=1695784 bytes_retransmit=9 bytes_invalid=0 send_seq=6839 receive_seq=6839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41875 bytes_read=126102 bytes_retransmit=9 bytes_invalid=0 send_seq=6826 receive_seq=6826 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95967 bytes_read=2590434 bytes_retransmit=0 bytes_invalid=0 send_seq=11385 receive_seq=11385 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998673 coil_temp=16.8 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.8 th2: temp=62.7 th3: temp=60.0 sysload=0.13 cputime=505.624 memavail=7392724 print_time=6666.239 buffer_time=2.060 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 100 Hz
Stats 6642.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31095725 bytes_read=4844459 bytes_retransmit=9 bytes_invalid=0 send_seq=587667 receive_seq=587667 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=47 upcoming_bytes=6169 freq=400016023 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41128 bytes_read=128647 bytes_retransmit=0 bytes_invalid=0 send_seq=6826 receive_seq=6826 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999476 adj=49997553 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=200522 bytes_read=6428279 bytes_retransmit=9 bytes_invalid=0 send_seq=27970 receive_seq=27970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997667 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136560 bytes_read=3724986 bytes_retransmit=9 bytes_invalid=0 send_seq=18927 receive_seq=18927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997553 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41395 bytes_read=1696078 bytes_retransmit=9 bytes_invalid=0 send_seq=6840 receive_seq=6840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41881 bytes_read=126129 bytes_retransmit=9 bytes_invalid=0 send_seq=6827 receive_seq=6827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95973 bytes_read=2590806 bytes_retransmit=0 bytes_invalid=0 send_seq=11386 receive_seq=11386 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998685 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.6 th2: temp=62.5 th3: temp=60.1 sysload=0.13 cputime=505.761 memavail=7392724 print_time=6667.438 buffer_time=2.248 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 101 Hz
Stats 6643.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31103165 bytes_read=4845444 bytes_retransmit=9 bytes_invalid=0 send_seq=587802 receive_seq=587802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=6206 freq=400016013 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=41134 bytes_read=128676 bytes_retransmit=0 bytes_invalid=0 send_seq=6827 receive_seq=6827 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999475 adj=49997534 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=200598 bytes_read=6431337 bytes_retransmit=9 bytes_invalid=0 send_seq=27981 receive_seq=27981 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997669 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136566 bytes_read=3725086 bytes_retransmit=9 bytes_invalid=0 send_seq=18928 receive_seq=18928 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997550 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41401 bytes_read=1696312 bytes_retransmit=9 bytes_invalid=0 send_seq=6841 receive_seq=6841 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997669 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41887 bytes_read=126145 bytes_retransmit=9 bytes_invalid=0 send_seq=6828 receive_seq=6828 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95979 bytes_read=2591162 bytes_retransmit=0 bytes_invalid=0 send_seq=11387 receive_seq=11387 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998684 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.7 th2: temp=62.8 th3: temp=60.1 sysload=0.13 cputime=505.885 memavail=7392724 print_time=6668.374 buffer_time=2.183 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 102 Hz
Stats 6644.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31111047 bytes_read=4846498 bytes_retransmit=9 bytes_invalid=0 send_seq=587945 receive_seq=587945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=26 upcoming_bytes=4322 freq=400015996 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=41140 bytes_read=128692 bytes_retransmit=0 bytes_invalid=0 send_seq=6828 receive_seq=6828 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999474 adj=49997529 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=200674 bytes_read=6434451 bytes_retransmit=9 bytes_invalid=0 send_seq=27992 receive_seq=27992 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997671 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136572 bytes_read=3725186 bytes_retransmit=9 bytes_invalid=0 send_seq=18929 receive_seq=18929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997553 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41407 bytes_read=1696561 bytes_retransmit=9 bytes_invalid=0 send_seq=6842 receive_seq=6842 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41893 bytes_read=126161 bytes_retransmit=9 bytes_invalid=0 send_seq=6829 receive_seq=6829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95985 bytes_read=2591518 bytes_retransmit=0 bytes_invalid=0 send_seq=11388 receive_seq=11388 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998689 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.7 th2: temp=62.7 th3: temp=60.2 sysload=0.13 cputime=506.010 memavail=7392724 print_time=6669.241 buffer_time=2.049 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 103 Hz
Stats 6645.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31117631 bytes_read=4847408 bytes_retransmit=9 bytes_invalid=0 send_seq=588066 receive_seq=588066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=6383 freq=400016028 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=41146 bytes_read=128708 bytes_retransmit=0 bytes_invalid=0 send_seq=6829 receive_seq=6829 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999472 adj=49997533 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=200750 bytes_read=6437536 bytes_retransmit=9 bytes_invalid=0 send_seq=28003 receive_seq=28003 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997695 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136578 bytes_read=3725328 bytes_retransmit=9 bytes_invalid=0 send_seq=18930 receive_seq=18930 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997573 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41413 bytes_read=1696855 bytes_retransmit=9 bytes_invalid=0 send_seq=6843 receive_seq=6843 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997693 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41899 bytes_read=126177 bytes_retransmit=9 bytes_invalid=0 send_seq=6830 receive_seq=6830 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95991 bytes_read=2591874 bytes_retransmit=0 bytes_invalid=0 send_seq=11389 receive_seq=11389 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998700 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.3 th1: temp=56.0 th2: temp=62.7 th3: temp=60.1 sysload=0.12 cputime=506.162 memavail=7393508 print_time=6670.444 buffer_time=2.248 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 104 Hz
Stats 6646.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31125226 bytes_read=4848413 bytes_retransmit=9 bytes_invalid=0 send_seq=588205 receive_seq=588205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=6442 freq=400016033 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=41152 bytes_read=128724 bytes_retransmit=0 bytes_invalid=0 send_seq=6830 receive_seq=6830 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999471 adj=49997448 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=200826 bytes_read=6440594 bytes_retransmit=9 bytes_invalid=0 send_seq=28014 receive_seq=28014 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997613 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136584 bytes_read=3725428 bytes_retransmit=9 bytes_invalid=0 send_seq=18931 receive_seq=18931 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997479 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41419 bytes_read=1697089 bytes_retransmit=9 bytes_invalid=0 send_seq=6844 receive_seq=6844 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41905 bytes_read=126204 bytes_retransmit=9 bytes_invalid=0 send_seq=6831 receive_seq=6831 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=95997 bytes_read=2592230 bytes_retransmit=0 bytes_invalid=0 send_seq=11390 receive_seq=11390 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998651 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.7 th1: temp=55.7 th2: temp=62.8 th3: temp=60.1 sysload=0.12 cputime=506.288 memavail=7393516 print_time=6671.375 buffer_time=2.178 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 105 Hz
Stats 6647.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31133190 bytes_read=4849478 bytes_retransmit=9 bytes_invalid=0 send_seq=588347 receive_seq=588347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=46 upcoming_bytes=4610 freq=400016063 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=41158 bytes_read=128740 bytes_retransmit=0 bytes_invalid=0 send_seq=6831 receive_seq=6831 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999472 adj=49997433 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=200902 bytes_read=6443668 bytes_retransmit=9 bytes_invalid=0 send_seq=28025 receive_seq=28025 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997599 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136590 bytes_read=3725528 bytes_retransmit=9 bytes_invalid=0 send_seq=18932 receive_seq=18932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997461 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41425 bytes_read=1697323 bytes_retransmit=9 bytes_invalid=0 send_seq=6845 receive_seq=6845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41911 bytes_read=126220 bytes_retransmit=9 bytes_invalid=0 send_seq=6832 receive_seq=6832 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999470 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96003 bytes_read=2592586 bytes_retransmit=0 bytes_invalid=0 send_seq=11391 receive_seq=11391 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998640 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.6 th2: temp=62.7 th3: temp=60.1 sysload=0.12 cputime=506.416 memavail=7392512 print_time=6672.249 buffer_time=2.051 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 106 Hz
Stats 6648.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31140087 bytes_read=4850413 bytes_retransmit=9 bytes_invalid=0 send_seq=588472 receive_seq=588472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=6569 freq=400016060 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41164 bytes_read=128769 bytes_retransmit=0 bytes_invalid=0 send_seq=6832 receive_seq=6832 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999471 adj=49997397 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=200978 bytes_read=6446813 bytes_retransmit=9 bytes_invalid=0 send_seq=28036 receive_seq=28036 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997543 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136596 bytes_read=3725656 bytes_retransmit=9 bytes_invalid=0 send_seq=18933 receive_seq=18933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997398 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41431 bytes_read=1697617 bytes_retransmit=9 bytes_invalid=0 send_seq=6846 receive_seq=6846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997574 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41917 bytes_read=126236 bytes_retransmit=9 bytes_invalid=0 send_seq=6833 receive_seq=6833 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96009 bytes_read=2592942 bytes_retransmit=0 bytes_invalid=0 send_seq=11392 receive_seq=11392 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998613 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.7 th2: temp=62.7 th3: temp=60.1 sysload=0.12 cputime=506.548 memavail=7392516 print_time=6673.447 buffer_time=2.242 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 107 Hz
Stats 6649.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31147709 bytes_read=4851413 bytes_retransmit=9 bytes_invalid=0 send_seq=588610 receive_seq=588610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=6779 freq=400016038 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41170 bytes_read=128785 bytes_retransmit=0 bytes_invalid=0 send_seq=6833 receive_seq=6833 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999470 adj=49997412 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=201054 bytes_read=6449871 bytes_retransmit=9 bytes_invalid=0 send_seq=28047 receive_seq=28047 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997566 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136602 bytes_read=3725756 bytes_retransmit=9 bytes_invalid=0 send_seq=18934 receive_seq=18934 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997424 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41437 bytes_read=1697866 bytes_retransmit=9 bytes_invalid=0 send_seq=6847 receive_seq=6847 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997596 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41923 bytes_read=126252 bytes_retransmit=9 bytes_invalid=0 send_seq=6834 receive_seq=6834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96015 bytes_read=2593298 bytes_retransmit=0 bytes_invalid=0 send_seq=11393 receive_seq=11393 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998626 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.6 th2: temp=62.7 th3: temp=60.1 sysload=0.12 cputime=506.673 memavail=7392516 print_time=6674.384 buffer_time=2.178 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 108 Hz
Stats 6650.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31155881 bytes_read=4852492 bytes_retransmit=9 bytes_invalid=0 send_seq=588758 receive_seq=588758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=4775 freq=400016028 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41176 bytes_read=128801 bytes_retransmit=0 bytes_invalid=0 send_seq=6834 receive_seq=6834 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999470 adj=49997445 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=201130 bytes_read=6452941 bytes_retransmit=9 bytes_invalid=0 send_seq=28058 receive_seq=28058 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997658 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136608 bytes_read=3725870 bytes_retransmit=9 bytes_invalid=0 send_seq=18935 receive_seq=18935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997468 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41443 bytes_read=1698100 bytes_retransmit=9 bytes_invalid=0 send_seq=6848 receive_seq=6848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997630 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41929 bytes_read=126268 bytes_retransmit=9 bytes_invalid=0 send_seq=6835 receive_seq=6835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96021 bytes_read=2593654 bytes_retransmit=0 bytes_invalid=0 send_seq=11394 receive_seq=11394 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998647 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.7 th2: temp=62.5 th3: temp=60.1 sysload=0.11 cputime=506.795 memavail=7392516 print_time=6675.251 buffer_time=2.045 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 109 Hz
Stats 6651.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31162881 bytes_read=4853442 bytes_retransmit=9 bytes_invalid=0 send_seq=588886 receive_seq=588886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=6843 freq=400016024 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41182 bytes_read=128817 bytes_retransmit=0 bytes_invalid=0 send_seq=6835 receive_seq=6835 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999469 adj=49997456 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=201206 bytes_read=6456015 bytes_retransmit=9 bytes_invalid=0 send_seq=28069 receive_seq=28069 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997670 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136614 bytes_read=3725998 bytes_retransmit=9 bytes_invalid=0 send_seq=18936 receive_seq=18936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997483 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41449 bytes_read=1698394 bytes_retransmit=9 bytes_invalid=0 send_seq=6849 receive_seq=6849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41935 bytes_read=126295 bytes_retransmit=9 bytes_invalid=0 send_seq=6836 receive_seq=6836 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96027 bytes_read=2594010 bytes_retransmit=0 bytes_invalid=0 send_seq=11395 receive_seq=11395 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998652 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.8 th2: temp=62.6 th3: temp=60.2 sysload=0.11 cputime=506.942 memavail=7394016 print_time=6676.459 buffer_time=2.249 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 110 Hz
Stats 6652.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31170609 bytes_read=4854463 bytes_retransmit=9 bytes_invalid=0 send_seq=589025 receive_seq=589025 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=7024 freq=400016032 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41188 bytes_read=128833 bytes_retransmit=0 bytes_invalid=0 send_seq=6836 receive_seq=6836 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999467 adj=49997451 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=201282 bytes_read=6459088 bytes_retransmit=9 bytes_invalid=0 send_seq=28080 receive_seq=28080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997661 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136620 bytes_read=3726098 bytes_retransmit=9 bytes_invalid=0 send_seq=18937 receive_seq=18937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41455 bytes_read=1698628 bytes_retransmit=9 bytes_invalid=0 send_seq=6850 receive_seq=6850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41941 bytes_read=126311 bytes_retransmit=9 bytes_invalid=0 send_seq=6837 receive_seq=6837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96033 bytes_read=2594366 bytes_retransmit=0 bytes_invalid=0 send_seq=11396 receive_seq=11396 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998659 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.7 th2: temp=62.6 th3: temp=60.1 sysload=0.11 cputime=507.065 memavail=7394136 print_time=6677.389 buffer_time=2.179 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 111 Hz
Stats 6653.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31178893 bytes_read=4855537 bytes_retransmit=9 bytes_invalid=0 send_seq=589172 receive_seq=589172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=4990 freq=400016054 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41194 bytes_read=128862 bytes_retransmit=0 bytes_invalid=0 send_seq=6837 receive_seq=6837 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999467 adj=49997420 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=201358 bytes_read=6462160 bytes_retransmit=9 bytes_invalid=0 send_seq=28091 receive_seq=28091 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997643 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136626 bytes_read=3726198 bytes_retransmit=9 bytes_invalid=0 send_seq=18938 receive_seq=18938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41461 bytes_read=1698862 bytes_retransmit=9 bytes_invalid=0 send_seq=6851 receive_seq=6851 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41947 bytes_read=126327 bytes_retransmit=9 bytes_invalid=0 send_seq=6838 receive_seq=6838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96039 bytes_read=2594722 bytes_retransmit=0 bytes_invalid=0 send_seq=11397 receive_seq=11397 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998653 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.7 th2: temp=62.7 th3: temp=60.1 sysload=0.11 cputime=507.189 memavail=7394136 print_time=6678.261 buffer_time=2.051 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 112 Hz
Stats 6654.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31185978 bytes_read=4856492 bytes_retransmit=9 bytes_invalid=0 send_seq=589302 receive_seq=589301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=7023 freq=400016037 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41200 bytes_read=128878 bytes_retransmit=0 bytes_invalid=0 send_seq=6838 receive_seq=6838 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999469 adj=49997386 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=201434 bytes_read=6465290 bytes_retransmit=9 bytes_invalid=0 send_seq=28102 receive_seq=28102 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997592 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136632 bytes_read=3726326 bytes_retransmit=9 bytes_invalid=0 send_seq=18939 receive_seq=18939 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997428 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41467 bytes_read=1699171 bytes_retransmit=9 bytes_invalid=0 send_seq=6852 receive_seq=6852 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997596 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41953 bytes_read=126343 bytes_retransmit=9 bytes_invalid=0 send_seq=6839 receive_seq=6839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96045 bytes_read=2595078 bytes_retransmit=0 bytes_invalid=0 send_seq=11398 receive_seq=11398 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998632 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.9 th2: temp=62.8 th3: temp=60.0 sysload=0.11 cputime=507.326 memavail=7394136 print_time=6679.461 buffer_time=2.250 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 113 Hz
Stats 6655.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31193821 bytes_read=4857507 bytes_retransmit=9 bytes_invalid=0 send_seq=589442 receive_seq=589442 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=7119 freq=400016072 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41206 bytes_read=128894 bytes_retransmit=0 bytes_invalid=0 send_seq=6839 receive_seq=6839 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999468 adj=49997455 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=201510 bytes_read=6468346 bytes_retransmit=9 bytes_invalid=0 send_seq=28113 receive_seq=28113 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997642 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136638 bytes_read=3726426 bytes_retransmit=9 bytes_invalid=0 send_seq=18940 receive_seq=18940 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997470 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41473 bytes_read=1699405 bytes_retransmit=9 bytes_invalid=0 send_seq=6853 receive_seq=6853 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997626 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41959 bytes_read=126359 bytes_retransmit=9 bytes_invalid=0 send_seq=6840 receive_seq=6840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96051 bytes_read=2595418 bytes_retransmit=0 bytes_invalid=0 send_seq=11399 receive_seq=11399 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998657 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.7 th2: temp=62.8 th3: temp=60.2 sysload=0.18 cputime=507.452 memavail=7394136 print_time=6680.395 buffer_time=2.183 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 114 Hz
Stats 6656.5: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31202203 bytes_read=4858584 bytes_retransmit=9 bytes_invalid=0 send_seq=589591 receive_seq=589591 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=5112 freq=400016052 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41212 bytes_read=128910 bytes_retransmit=0 bytes_invalid=0 send_seq=6840 receive_seq=6840 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999467 adj=49997399 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=201586 bytes_read=6471417 bytes_retransmit=9 bytes_invalid=0 send_seq=28124 receive_seq=28124 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997610 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136644 bytes_read=3726540 bytes_retransmit=9 bytes_invalid=0 send_seq=18941 receive_seq=18941 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997400 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41479 bytes_read=1699639 bytes_retransmit=9 bytes_invalid=0 send_seq=6854 receive_seq=6854 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997599 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41965 bytes_read=126386 bytes_retransmit=9 bytes_invalid=0 send_seq=6841 receive_seq=6841 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96057 bytes_read=2595774 bytes_retransmit=0 bytes_invalid=0 send_seq=11400 receive_seq=11400 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998623 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.6 th2: temp=62.7 th3: temp=60.1 sysload=0.18 cputime=507.581 memavail=7393884 print_time=6681.268 buffer_time=2.056 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 115 Hz
Stats 6657.6: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31209455 bytes_read=4859580 bytes_retransmit=9 bytes_invalid=0 send_seq=589725 receive_seq=589725 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=47 upcoming_bytes=7170 freq=400016052 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41218 bytes_read=128926 bytes_retransmit=0 bytes_invalid=0 send_seq=6841 receive_seq=6841 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999467 adj=49997428 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=201655 bytes_read=6474483 bytes_retransmit=9 bytes_invalid=0 send_seq=28134 receive_seq=28134 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997645 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136650 bytes_read=3726668 bytes_retransmit=9 bytes_invalid=0 send_seq=18942 receive_seq=18942 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997443 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41485 bytes_read=1699933 bytes_retransmit=9 bytes_invalid=0 send_seq=6855 receive_seq=6855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997632 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41971 bytes_read=126402 bytes_retransmit=9 bytes_invalid=0 send_seq=6842 receive_seq=6842 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96063 bytes_read=2596146 bytes_retransmit=0 bytes_invalid=0 send_seq=11401 receive_seq=11401 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998644 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.7 th2: temp=62.6 th3: temp=60.2 sysload=0.18 cputime=507.720 memavail=7393424 print_time=6682.466 buffer_time=2.245 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 116 Hz
Stats 6658.6: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31217218 bytes_read=4860585 bytes_retransmit=9 bytes_invalid=0 send_seq=589864 receive_seq=589864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=7545 freq=400016052 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41224 bytes_read=128942 bytes_retransmit=0 bytes_invalid=0 send_seq=6842 receive_seq=6842 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999466 adj=49997436 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=201731 bytes_read=6477539 bytes_retransmit=9 bytes_invalid=0 send_seq=28145 receive_seq=28145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997635 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136656 bytes_read=3726768 bytes_retransmit=9 bytes_invalid=0 send_seq=18943 receive_seq=18943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997464 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41491 bytes_read=1700167 bytes_retransmit=9 bytes_invalid=0 send_seq=6856 receive_seq=6856 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41977 bytes_read=126418 bytes_retransmit=9 bytes_invalid=0 send_seq=6843 receive_seq=6843 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96069 bytes_read=2596502 bytes_retransmit=0 bytes_invalid=0 send_seq=11402 receive_seq=11402 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998648 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.7 th2: temp=62.8 th3: temp=60.2 sysload=0.18 cputime=507.845 memavail=7393436 print_time=6683.394 buffer_time=2.173 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 117 Hz
Stats 6659.6: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31225921 bytes_read=4861694 bytes_retransmit=9 bytes_invalid=0 send_seq=590018 receive_seq=590018 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=5328 freq=400016280 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41230 bytes_read=128971 bytes_retransmit=0 bytes_invalid=0 send_seq=6843 receive_seq=6843 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999465 adj=49997427 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=201807 bytes_read=6480669 bytes_retransmit=9 bytes_invalid=0 send_seq=28156 receive_seq=28156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997626 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136662 bytes_read=3726868 bytes_retransmit=9 bytes_invalid=0 send_seq=18944 receive_seq=18944 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997687 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41497 bytes_read=1700416 bytes_retransmit=9 bytes_invalid=0 send_seq=6857 receive_seq=6857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41983 bytes_read=126434 bytes_retransmit=9 bytes_invalid=0 send_seq=6844 receive_seq=6844 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96075 bytes_read=2596858 bytes_retransmit=0 bytes_invalid=0 send_seq=11403 receive_seq=11403 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998652 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.5 th2: temp=62.8 th3: temp=60.0 sysload=0.18 cputime=507.973 memavail=7393436 print_time=6684.269 buffer_time=2.046 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 118 Hz
Stats 6660.6: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31233247 bytes_read=4862649 bytes_retransmit=9 bytes_invalid=0 send_seq=590147 receive_seq=590147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=7251 freq=400016269 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41236 bytes_read=128987 bytes_retransmit=0 bytes_invalid=0 send_seq=6844 receive_seq=6844 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999465 adj=49997043 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=201883 bytes_read=6483741 bytes_retransmit=9 bytes_invalid=0 send_seq=28167 receive_seq=28167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997233 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136668 bytes_read=3726996 bytes_retransmit=9 bytes_invalid=0 send_seq=18945 receive_seq=18945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997176 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41503 bytes_read=1700710 bytes_retransmit=9 bytes_invalid=0 send_seq=6858 receive_seq=6858 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999566 adj=47997320 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41989 bytes_read=126450 bytes_retransmit=9 bytes_invalid=0 send_seq=6845 receive_seq=6845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999352 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96081 bytes_read=2597214 bytes_retransmit=0 bytes_invalid=0 send_seq=11404 receive_seq=11404 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998415 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.6 th2: temp=62.7 th3: temp=60.2 sysload=0.25 cputime=508.111 memavail=7393436 print_time=6685.474 buffer_time=2.251 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 119 Hz
Stats 6661.6: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31241194 bytes_read=4863679 bytes_retransmit=9 bytes_invalid=0 send_seq=590291 receive_seq=590291 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=7492 freq=400016292 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41242 bytes_read=129003 bytes_retransmit=0 bytes_invalid=0 send_seq=6845 receive_seq=6845 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999488 adj=49997183 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=201959 bytes_read=6486800 bytes_retransmit=9 bytes_invalid=0 send_seq=28178 receive_seq=28178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997365 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136674 bytes_read=3727110 bytes_retransmit=9 bytes_invalid=0 send_seq=18946 receive_seq=18946 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997288 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41509 bytes_read=1700944 bytes_retransmit=9 bytes_invalid=0 send_seq=6859 receive_seq=6859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999566 adj=47997482 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=41995 bytes_read=126477 bytes_retransmit=9 bytes_invalid=0 send_seq=6846 receive_seq=6846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999378 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96087 bytes_read=2597554 bytes_retransmit=0 bytes_invalid=0 send_seq=11405 receive_seq=11405 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998495 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.8 th2: temp=63.0 th3: temp=60.1 sysload=0.25 cputime=508.235 memavail=7393436 print_time=6686.400 buffer_time=2.177 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 120 Hz
Stats 6662.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31249788 bytes_read=4864809 bytes_retransmit=9 bytes_invalid=0 send_seq=590446 receive_seq=590446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=5327 freq=400016252 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41248 bytes_read=129019 bytes_retransmit=0 bytes_invalid=0 send_seq=6846 receive_seq=6846 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999487 adj=49997455 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=202035 bytes_read=6489888 bytes_retransmit=9 bytes_invalid=0 send_seq=28189 receive_seq=28189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997352 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136680 bytes_read=3727224 bytes_retransmit=9 bytes_invalid=0 send_seq=18947 receive_seq=18947 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997249 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41515 bytes_read=1701178 bytes_retransmit=9 bytes_invalid=0 send_seq=6860 receive_seq=6860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999565 adj=47997456 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42001 bytes_read=126493 bytes_retransmit=9 bytes_invalid=0 send_seq=6847 receive_seq=6847 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999372 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96093 bytes_read=2597910 bytes_retransmit=0 bytes_invalid=0 send_seq=11406 receive_seq=11406 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998489 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.8 th2: temp=62.8 th3: temp=60.3 sysload=0.25 cputime=508.362 memavail=7393436 print_time=6687.274 buffer_time=2.050 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 121 Hz
Stats 6663.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31257272 bytes_read=4865789 bytes_retransmit=9 bytes_invalid=0 send_seq=590580 receive_seq=590580 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=7273 freq=400016235 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41254 bytes_read=129035 bytes_retransmit=0 bytes_invalid=0 send_seq=6847 receive_seq=6847 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999485 adj=49997514 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=202111 bytes_read=6492959 bytes_retransmit=9 bytes_invalid=0 send_seq=28200 receive_seq=28200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997450 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136686 bytes_read=3727338 bytes_retransmit=9 bytes_invalid=0 send_seq=18948 receive_seq=18948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997337 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41521 bytes_read=1701472 bytes_retransmit=9 bytes_invalid=0 send_seq=6861 receive_seq=6861 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999565 adj=47997524 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42007 bytes_read=126509 bytes_retransmit=9 bytes_invalid=0 send_seq=6848 receive_seq=6848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999412 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96099 bytes_read=2598282 bytes_retransmit=0 bytes_invalid=0 send_seq=11407 receive_seq=11407 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998541 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.8 th2: temp=62.7 th3: temp=60.0 sysload=0.25 cputime=508.503 memavail=7393436 print_time=6688.478 buffer_time=2.249 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 122 Hz
Stats 6664.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31265120 bytes_read=4866804 bytes_retransmit=9 bytes_invalid=0 send_seq=590721 receive_seq=590721 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=7725 freq=400016240 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41260 bytes_read=129064 bytes_retransmit=0 bytes_invalid=0 send_seq=6848 receive_seq=6848 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999485 adj=49997500 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=202187 bytes_read=6496019 bytes_retransmit=9 bytes_invalid=0 send_seq=28211 receive_seq=28211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997520 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136692 bytes_read=3727438 bytes_retransmit=9 bytes_invalid=0 send_seq=18949 receive_seq=18949 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997406 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41527 bytes_read=1701721 bytes_retransmit=9 bytes_invalid=0 send_seq=6862 receive_seq=6862 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997574 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42013 bytes_read=126525 bytes_retransmit=9 bytes_invalid=0 send_seq=6849 receive_seq=6849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96105 bytes_read=2598622 bytes_retransmit=0 bytes_invalid=0 send_seq=11408 receive_seq=11408 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998595 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.8 th2: temp=62.6 th3: temp=60.1 sysload=0.25 cputime=508.632 memavail=7393436 print_time=6689.404 buffer_time=2.174 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 123 Hz
Stats 6665.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31273837 bytes_read=4867923 bytes_retransmit=9 bytes_invalid=0 send_seq=590877 receive_seq=590877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=5578 freq=400016215 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41266 bytes_read=129080 bytes_retransmit=0 bytes_invalid=0 send_seq=6849 receive_seq=6849 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999483 adj=49997485 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=202263 bytes_read=6499164 bytes_retransmit=9 bytes_invalid=0 send_seq=28222 receive_seq=28222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997570 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136698 bytes_read=3727552 bytes_retransmit=9 bytes_invalid=0 send_seq=18950 receive_seq=18950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997392 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41533 bytes_read=1701955 bytes_retransmit=9 bytes_invalid=0 send_seq=6863 receive_seq=6863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997566 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42019 bytes_read=126541 bytes_retransmit=9 bytes_invalid=0 send_seq=6850 receive_seq=6850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999423 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96111 bytes_read=2598978 bytes_retransmit=0 bytes_invalid=0 send_seq=11409 receive_seq=11409 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998592 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.7 th2: temp=62.6 th3: temp=60.1 sysload=0.23 cputime=508.762 memavail=7393436 print_time=6690.275 buffer_time=2.044 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 124 Hz
Stats 6666.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31281463 bytes_read=4868921 bytes_retransmit=9 bytes_invalid=0 send_seq=591015 receive_seq=591015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=7541 freq=400016192 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41272 bytes_read=129096 bytes_retransmit=0 bytes_invalid=0 send_seq=6850 receive_seq=6850 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999483 adj=49997499 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=202339 bytes_read=6502222 bytes_retransmit=9 bytes_invalid=0 send_seq=28233 receive_seq=28233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997612 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136704 bytes_read=3727680 bytes_retransmit=9 bytes_invalid=0 send_seq=18951 receive_seq=18951 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997436 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41539 bytes_read=1702249 bytes_retransmit=9 bytes_invalid=0 send_seq=6864 receive_seq=6864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997603 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42025 bytes_read=126568 bytes_retransmit=9 bytes_invalid=0 send_seq=6851 receive_seq=6851 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96117 bytes_read=2599334 bytes_retransmit=0 bytes_invalid=0 send_seq=11410 receive_seq=11410 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998617 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.8 th2: temp=62.8 th3: temp=60.1 sysload=0.23 cputime=508.904 memavail=7393208 print_time=6691.479 buffer_time=2.248 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 125 Hz
Stats 6667.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31289411 bytes_read=4869949 bytes_retransmit=9 bytes_invalid=0 send_seq=591156 receive_seq=591156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=7878 freq=400016321 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41278 bytes_read=129112 bytes_retransmit=0 bytes_invalid=0 send_seq=6851 receive_seq=6851 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999481 adj=49997518 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=202415 bytes_read=6505298 bytes_retransmit=9 bytes_invalid=0 send_seq=28244 receive_seq=28244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997647 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136710 bytes_read=3727780 bytes_retransmit=9 bytes_invalid=0 send_seq=18952 receive_seq=18952 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997475 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41545 bytes_read=1702483 bytes_retransmit=9 bytes_invalid=0 send_seq=6865 receive_seq=6865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997629 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42031 bytes_read=126584 bytes_retransmit=9 bytes_invalid=0 send_seq=6852 receive_seq=6852 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96123 bytes_read=2599690 bytes_retransmit=0 bytes_invalid=0 send_seq=11411 receive_seq=11411 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998648 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.7 th2: temp=62.8 th3: temp=60.1 sysload=0.23 cputime=509.034 memavail=7392220 print_time=6692.405 buffer_time=2.173 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 126 Hz
Stats 6668.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31298310 bytes_read=4871093 bytes_retransmit=9 bytes_invalid=0 send_seq=591317 receive_seq=591317 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=5556 freq=400016280 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41284 bytes_read=129128 bytes_retransmit=0 bytes_invalid=0 send_seq=6852 receive_seq=6852 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999480 adj=49997284 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=202491 bytes_read=6508382 bytes_retransmit=9 bytes_invalid=0 send_seq=28255 receive_seq=28255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997379 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136716 bytes_read=3727894 bytes_retransmit=9 bytes_invalid=0 send_seq=18953 receive_seq=18953 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997207 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41551 bytes_read=1702717 bytes_retransmit=9 bytes_invalid=0 send_seq=6866 receive_seq=6866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997435 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42037 bytes_read=126600 bytes_retransmit=9 bytes_invalid=0 send_seq=6853 receive_seq=6853 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999383 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96129 bytes_read=2600036 bytes_retransmit=0 bytes_invalid=0 send_seq=11412 receive_seq=11412 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998522 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.8 th2: temp=62.7 th3: temp=60.1 sysload=0.23 cputime=509.175 memavail=7394496 print_time=6693.275 buffer_time=2.042 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 127 Hz
Stats 6669.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31306026 bytes_read=4872103 bytes_retransmit=9 bytes_invalid=0 send_seq=591457 receive_seq=591457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=7472 freq=400016247 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41290 bytes_read=129157 bytes_retransmit=0 bytes_invalid=0 send_seq=6853 receive_seq=6853 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999478 adj=49997350 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=202567 bytes_read=6511438 bytes_retransmit=9 bytes_invalid=0 send_seq=28266 receive_seq=28266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997497 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136722 bytes_read=3728008 bytes_retransmit=9 bytes_invalid=0 send_seq=18954 receive_seq=18954 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997337 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41557 bytes_read=1703026 bytes_retransmit=9 bytes_invalid=0 send_seq=6867 receive_seq=6867 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997511 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42043 bytes_read=126616 bytes_retransmit=9 bytes_invalid=0 send_seq=6854 receive_seq=6854 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999402 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96135 bytes_read=2600381 bytes_retransmit=0 bytes_invalid=0 send_seq=11413 receive_seq=11413 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998575 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.5 th2: temp=62.9 th3: temp=60.1 sysload=0.23 cputime=509.319 memavail=7394588 print_time=6694.475 buffer_time=2.242 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 128 Hz
Stats 6670.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31313900 bytes_read=4873123 bytes_retransmit=9 bytes_invalid=0 send_seq=591599 receive_seq=591599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=8090 freq=400016213 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41296 bytes_read=129173 bytes_retransmit=0 bytes_invalid=0 send_seq=6854 receive_seq=6854 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999476 adj=49997406 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=202636 bytes_read=6514472 bytes_retransmit=9 bytes_invalid=0 send_seq=28276 receive_seq=28276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997610 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136728 bytes_read=3728108 bytes_retransmit=9 bytes_invalid=0 send_seq=18955 receive_seq=18955 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997426 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41563 bytes_read=1703260 bytes_retransmit=9 bytes_invalid=0 send_seq=6868 receive_seq=6868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997580 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42049 bytes_read=126632 bytes_retransmit=9 bytes_invalid=0 send_seq=6855 receive_seq=6855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999421 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96141 bytes_read=2600725 bytes_retransmit=0 bytes_invalid=0 send_seq=11414 receive_seq=11414 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998626 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.6 th2: temp=62.8 th3: temp=60.1 sysload=0.21 cputime=509.446 memavail=7394588 print_time=6695.411 buffer_time=2.177 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 129 Hz
Stats 6671.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31322792 bytes_read=4874247 bytes_retransmit=9 bytes_invalid=0 send_seq=591756 receive_seq=591756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=5777 freq=400016200 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41302 bytes_read=129189 bytes_retransmit=0 bytes_invalid=0 send_seq=6855 receive_seq=6855 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999476 adj=49997441 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=202712 bytes_read=6517615 bytes_retransmit=9 bytes_invalid=0 send_seq=28287 receive_seq=28287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997668 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136734 bytes_read=3728236 bytes_retransmit=9 bytes_invalid=0 send_seq=18956 receive_seq=18956 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41569 bytes_read=1703494 bytes_retransmit=9 bytes_invalid=0 send_seq=6869 receive_seq=6869 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997626 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42055 bytes_read=126659 bytes_retransmit=9 bytes_invalid=0 send_seq=6856 receive_seq=6856 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96147 bytes_read=2601070 bytes_retransmit=0 bytes_invalid=0 send_seq=11415 receive_seq=11415 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998656 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.9 th2: temp=62.5 th3: temp=60.1 sysload=0.21 cputime=509.577 memavail=7394588 print_time=6696.285 buffer_time=2.050 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 130 Hz
Stats 6672.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31330703 bytes_read=4875288 bytes_retransmit=9 bytes_invalid=0 send_seq=591899 receive_seq=591899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=7589 freq=400016180 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41308 bytes_read=129205 bytes_retransmit=0 bytes_invalid=0 send_seq=6856 receive_seq=6856 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999474 adj=49997471 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=202788 bytes_read=6520689 bytes_retransmit=9 bytes_invalid=0 send_seq=28298 receive_seq=28298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997697 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136740 bytes_read=3728350 bytes_retransmit=9 bytes_invalid=0 send_seq=18957 receive_seq=18957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997522 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41575 bytes_read=1703788 bytes_retransmit=9 bytes_invalid=0 send_seq=6870 receive_seq=6870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997649 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42061 bytes_read=126675 bytes_retransmit=9 bytes_invalid=0 send_seq=6857 receive_seq=6857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96153 bytes_read=2601415 bytes_retransmit=0 bytes_invalid=0 send_seq=11416 receive_seq=11416 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998665 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.8 th2: temp=62.5 th3: temp=60.1 sysload=0.21 cputime=509.725 memavail=7394588 print_time=6697.484 buffer_time=2.249 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 131 Hz
Stats 6673.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31338603 bytes_read=4876303 bytes_retransmit=9 bytes_invalid=0 send_seq=592040 receive_seq=592040 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=8251 freq=400016158 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41314 bytes_read=129221 bytes_retransmit=0 bytes_invalid=0 send_seq=6857 receive_seq=6857 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999472 adj=49997469 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=202864 bytes_read=6523746 bytes_retransmit=9 bytes_invalid=0 send_seq=28309 receive_seq=28309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997716 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136746 bytes_read=3728450 bytes_retransmit=9 bytes_invalid=0 send_seq=18958 receive_seq=18958 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997535 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41581 bytes_read=1704022 bytes_retransmit=9 bytes_invalid=0 send_seq=6871 receive_seq=6871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42067 bytes_read=126691 bytes_retransmit=9 bytes_invalid=0 send_seq=6858 receive_seq=6858 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96159 bytes_read=2601760 bytes_retransmit=0 bytes_invalid=0 send_seq=11417 receive_seq=11417 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998672 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.7 th2: temp=62.8 th3: temp=60.1 sysload=0.21 cputime=509.857 memavail=7394588 print_time=6698.410 buffer_time=2.173 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 132 Hz
Stats 6674.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31347592 bytes_read=4877442 bytes_retransmit=9 bytes_invalid=0 send_seq=592200 receive_seq=592200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=6022 freq=400016148 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41320 bytes_read=129250 bytes_retransmit=0 bytes_invalid=0 send_seq=6858 receive_seq=6858 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999471 adj=49997473 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=202940 bytes_read=6526833 bytes_retransmit=9 bytes_invalid=0 send_seq=28320 receive_seq=28320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997762 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136752 bytes_read=3728564 bytes_retransmit=9 bytes_invalid=0 send_seq=18959 receive_seq=18959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997622 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41587 bytes_read=1704271 bytes_retransmit=9 bytes_invalid=0 send_seq=6872 receive_seq=6872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42073 bytes_read=126707 bytes_retransmit=9 bytes_invalid=0 send_seq=6859 receive_seq=6859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96165 bytes_read=2602105 bytes_retransmit=0 bytes_invalid=0 send_seq=11418 receive_seq=11418 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998688 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.8 th2: temp=62.6 th3: temp=60.1 sysload=0.21 cputime=509.990 memavail=7394340 print_time=6699.285 buffer_time=2.048 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Stats 6675.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31355643 bytes_read=4878482 bytes_retransmit=9 bytes_invalid=0 send_seq=592346 receive_seq=592346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=7251 freq=400016133 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41326 bytes_read=129266 bytes_retransmit=0 bytes_invalid=0 send_seq=6859 receive_seq=6859 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999472 adj=49997471 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=203016 bytes_read=6529890 bytes_retransmit=9 bytes_invalid=0 send_seq=28331 receive_seq=28331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997766 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136758 bytes_read=3728678 bytes_retransmit=9 bytes_invalid=0 send_seq=18960 receive_seq=18960 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997613 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41593 bytes_read=1704565 bytes_retransmit=9 bytes_invalid=0 send_seq=6873 receive_seq=6873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42079 bytes_read=126723 bytes_retransmit=9 bytes_invalid=0 send_seq=6860 receive_seq=6860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96171 bytes_read=2602450 bytes_retransmit=0 bytes_invalid=0 send_seq=11419 receive_seq=11419 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998701 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.8 th2: temp=62.7 th3: temp=60.0 sysload=0.19 cputime=510.123 memavail=7394116 print_time=6700.262 buffer_time=2.025 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6676.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31363701 bytes_read=4879517 bytes_retransmit=9 bytes_invalid=0 send_seq=592491 receive_seq=592491 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=102 freq=400016111 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41332 bytes_read=129282 bytes_retransmit=0 bytes_invalid=0 send_seq=6860 receive_seq=6860 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999470 adj=49997506 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=203092 bytes_read=6532948 bytes_retransmit=9 bytes_invalid=0 send_seq=28342 receive_seq=28342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997765 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136764 bytes_read=3728792 bytes_retransmit=9 bytes_invalid=0 send_seq=18961 receive_seq=18961 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997607 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41599 bytes_read=1704799 bytes_retransmit=9 bytes_invalid=0 send_seq=6874 receive_seq=6874 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42085 bytes_read=126750 bytes_retransmit=9 bytes_invalid=0 send_seq=6861 receive_seq=6861 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96177 bytes_read=2602800 bytes_retransmit=0 bytes_invalid=0 send_seq=11420 receive_seq=11420 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998711 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.8 th1: temp=55.6 th2: temp=62.7 th3: temp=60.2 sysload=0.19 cputime=510.206 memavail=7394116 print_time=6700.262 buffer_time=1.024 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6677.6: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31364114 bytes_read=4879987 bytes_retransmit=9 bytes_invalid=0 send_seq=592515 receive_seq=592515 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016084 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41338 bytes_read=129298 bytes_retransmit=0 bytes_invalid=0 send_seq=6861 receive_seq=6861 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999469 adj=49997522 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=203168 bytes_read=6536050 bytes_retransmit=9 bytes_invalid=0 send_seq=28353 receive_seq=28353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997875 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136770 bytes_read=3728906 bytes_retransmit=9 bytes_invalid=0 send_seq=18962 receive_seq=18962 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997651 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41605 bytes_read=1705033 bytes_retransmit=9 bytes_invalid=0 send_seq=6875 receive_seq=6875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997740 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42091 bytes_read=126766 bytes_retransmit=9 bytes_invalid=0 send_seq=6862 receive_seq=6862 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96183 bytes_read=2603156 bytes_retransmit=0 bytes_invalid=0 send_seq=11421 receive_seq=11421 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998735 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.6 th1: temp=55.7 th2: temp=63.0 th3: temp=60.2 sysload=0.19 cputime=510.271 memavail=7393612 print_time=6700.262 buffer_time=0.023 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
LIS2DW finished 'toolboard_t0' measurements
Resonances data written to /tmp/resonances_x_125.000_250.000_20.000_t0_mirror.csv file
Probing point (125.000, 250.000, 20.000)
Stats 6678.6: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31364610 bytes_read=4880431 bytes_retransmit=9 bytes_invalid=0 send_seq=592542 receive_seq=592542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016067 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41344 bytes_read=129314 bytes_retransmit=0 bytes_invalid=0 send_seq=6862 receive_seq=6862 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999470 adj=49997553 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=203236 bytes_read=6536705 bytes_retransmit=9 bytes_invalid=0 send_seq=28361 receive_seq=28361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997916 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136776 bytes_read=3729020 bytes_retransmit=9 bytes_invalid=0 send_seq=18963 receive_seq=18963 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997718 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41611 bytes_read=1705327 bytes_retransmit=9 bytes_invalid=0 send_seq=6876 receive_seq=6876 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997775 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42097 bytes_read=126782 bytes_retransmit=9 bytes_invalid=0 send_seq=6863 receive_seq=6863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999471 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96189 bytes_read=2603512 bytes_retransmit=0 bytes_invalid=0 send_seq=11422 receive_seq=11422 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998775 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.3 th1: temp=56.0 th2: temp=62.7 th3: temp=60.1 sysload=0.19 cputime=510.382 memavail=7395552 print_time=6701.245 buffer_time=0.006 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t0' measurements
toolhead: max_velocity: 600.000000
max_accel: 8379.841000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance testing
Testing frequency 10 Hz
Testing frequency 11 Hz
Testing frequency 12 Hz
Stats 6679.6: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31374209 bytes_read=4881621 bytes_retransmit=9 bytes_invalid=0 send_seq=592718 receive_seq=592718 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=0 freq=400016044 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41350 bytes_read=129343 bytes_retransmit=0 bytes_invalid=0 send_seq=6863 receive_seq=6863 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999468 adj=49997596 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=203412 bytes_read=6539693 bytes_retransmit=9 bytes_invalid=0 send_seq=28382 receive_seq=28382 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997965 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136782 bytes_read=3729120 bytes_retransmit=9 bytes_invalid=0 send_seq=18964 receive_seq=18964 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997814 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41617 bytes_read=1705576 bytes_retransmit=9 bytes_invalid=0 send_seq=6877 receive_seq=6877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997834 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42103 bytes_read=126798 bytes_retransmit=9 bytes_invalid=0 send_seq=6864 receive_seq=6864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999489 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96195 bytes_read=2603868 bytes_retransmit=0 bytes_invalid=0 send_seq=11423 receive_seq=11423 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998852 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.7 th2: temp=63.0 th3: temp=60.1 sysload=0.19 cputime=510.580 memavail=7395552 print_time=6704.409 buffer_time=2.169 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 13 Hz
Stats 6680.6: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31377802 bytes_read=4882330 bytes_retransmit=9 bytes_invalid=0 send_seq=592792 receive_seq=592792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=0 freq=400016021 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41356 bytes_read=129359 bytes_retransmit=0 bytes_invalid=0 send_seq=6864 receive_seq=6864 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999467 adj=49997499 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=203488 bytes_read=6542723 bytes_retransmit=9 bytes_invalid=0 send_seq=28393 receive_seq=28393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997746 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136788 bytes_read=3729234 bytes_retransmit=9 bytes_invalid=0 send_seq=18965 receive_seq=18965 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997591 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41623 bytes_read=1705810 bytes_retransmit=9 bytes_invalid=0 send_seq=6878 receive_seq=6878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997704 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42109 bytes_read=126814 bytes_retransmit=9 bytes_invalid=0 send_seq=6865 receive_seq=6865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999456 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96201 bytes_read=2604224 bytes_retransmit=0 bytes_invalid=0 send_seq=11424 receive_seq=11424 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998715 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.8 th2: temp=62.8 th3: temp=60.2 sysload=0.18 cputime=510.663 memavail=7395552 print_time=6705.252 buffer_time=2.011 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 14 Hz
Stats 6681.6: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31382624 bytes_read=4883115 bytes_retransmit=9 bytes_invalid=0 send_seq=592887 receive_seq=592887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=140 freq=400015998 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41362 bytes_read=129375 bytes_retransmit=0 bytes_invalid=0 send_seq=6865 receive_seq=6865 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999465 adj=49997518 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=203564 bytes_read=6545835 bytes_retransmit=9 bytes_invalid=0 send_seq=28404 receive_seq=28404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997777 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136794 bytes_read=3729362 bytes_retransmit=9 bytes_invalid=0 send_seq=18966 receive_seq=18966 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997619 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41629 bytes_read=1706104 bytes_retransmit=9 bytes_invalid=0 send_seq=6879 receive_seq=6879 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999565 adj=47997727 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42115 bytes_read=126841 bytes_retransmit=9 bytes_invalid=0 send_seq=6866 receive_seq=6866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999469 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96207 bytes_read=2604580 bytes_retransmit=0 bytes_invalid=0 send_seq=11425 receive_seq=11425 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998753 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.2 th1: temp=55.8 th2: temp=62.5 th3: temp=60.0 sysload=0.18 cputime=510.750 memavail=7395552 print_time=6706.274 buffer_time=2.033 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 15 Hz
Stats 6682.6: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=31387376 bytes_read=4883906 bytes_retransmit=9 bytes_invalid=0 send_seq=592980 receive_seq=592980 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=1344 freq=400015975 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41368 bytes_read=129391 bytes_retransmit=0 bytes_invalid=0 send_seq=6866 receive_seq=6866 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999464 adj=49997527 toolboard_t0: mcu_awake=0.262 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=203640 bytes_read=6548910 bytes_retransmit=9 bytes_invalid=0 send_seq=28415 receive_seq=28415 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997789 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136800 bytes_read=3729462 bytes_retransmit=9 bytes_invalid=0 send_seq=18967 receive_seq=18967 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997628 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41635 bytes_read=1706338 bytes_retransmit=9 bytes_invalid=0 send_seq=6880 receive_seq=6880 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999565 adj=47997813 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42121 bytes_read=126857 bytes_retransmit=9 bytes_invalid=0 send_seq=6867 receive_seq=6867 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999469 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96213 bytes_read=2604936 bytes_retransmit=0 bytes_invalid=0 send_seq=11426 receive_seq=11426 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998756 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.8 th2: temp=62.6 th3: temp=60.0 sysload=0.18 cputime=510.845 memavail=7395552 print_time=6707.473 buffer_time=2.232 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 16 Hz
Stats 6683.6: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=31392272 bytes_read=4884710 bytes_retransmit=9 bytes_invalid=0 send_seq=593073 receive_seq=593073 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=604 freq=400015951 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41374 bytes_read=129407 bytes_retransmit=0 bytes_invalid=0 send_seq=6867 receive_seq=6867 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999463 adj=49997530 toolboard_t0: mcu_awake=0.262 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=203716 bytes_read=6551995 bytes_retransmit=9 bytes_invalid=0 send_seq=28426 receive_seq=28426 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997786 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136806 bytes_read=3729576 bytes_retransmit=9 bytes_invalid=0 send_seq=18968 receive_seq=18968 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997625 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41641 bytes_read=1706572 bytes_retransmit=9 bytes_invalid=0 send_seq=6881 receive_seq=6881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997793 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42127 bytes_read=126873 bytes_retransmit=9 bytes_invalid=0 send_seq=6868 receive_seq=6868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999470 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96219 bytes_read=2605292 bytes_retransmit=0 bytes_invalid=0 send_seq=11427 receive_seq=11427 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998751 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.9 th2: temp=62.5 th3: temp=59.9 sysload=0.18 cputime=510.938 memavail=7395576 print_time=6708.388 buffer_time=2.146 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 17 Hz
Stats 6684.6: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=31396784 bytes_read=4885435 bytes_retransmit=9 bytes_invalid=0 send_seq=593156 receive_seq=593156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=1421 freq=400015939 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41380 bytes_read=129436 bytes_retransmit=0 bytes_invalid=0 send_seq=6868 receive_seq=6868 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999461 adj=49997545 toolboard_t0: mcu_awake=0.262 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=203792 bytes_read=6555051 bytes_retransmit=9 bytes_invalid=0 send_seq=28437 receive_seq=28437 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997818 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136812 bytes_read=3729690 bytes_retransmit=9 bytes_invalid=0 send_seq=18969 receive_seq=18969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997684 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41647 bytes_read=1706881 bytes_retransmit=9 bytes_invalid=0 send_seq=6882 receive_seq=6882 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997799 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42133 bytes_read=126889 bytes_retransmit=9 bytes_invalid=0 send_seq=6869 receive_seq=6869 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999480 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96225 bytes_read=2605648 bytes_retransmit=0 bytes_invalid=0 send_seq=11428 receive_seq=11428 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998762 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.8 th2: temp=62.6 th3: temp=59.9 sysload=0.18 cputime=511.031 memavail=7395576 print_time=6709.297 buffer_time=2.055 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 18 Hz
Stats 6685.6: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=31402075 bytes_read=4886235 bytes_retransmit=9 bytes_invalid=0 send_seq=593254 receive_seq=593254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=792 freq=400016051 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41386 bytes_read=129452 bytes_retransmit=0 bytes_invalid=0 send_seq=6869 receive_seq=6869 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999459 adj=49997531 toolboard_t0: mcu_awake=0.262 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=203868 bytes_read=6558108 bytes_retransmit=9 bytes_invalid=0 send_seq=28448 receive_seq=28448 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997837 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136818 bytes_read=3729790 bytes_retransmit=9 bytes_invalid=0 send_seq=18970 receive_seq=18970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997674 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41653 bytes_read=1707115 bytes_retransmit=9 bytes_invalid=0 send_seq=6883 receive_seq=6883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997798 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42139 bytes_read=126905 bytes_retransmit=9 bytes_invalid=0 send_seq=6870 receive_seq=6870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999474 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96231 bytes_read=2606004 bytes_retransmit=0 bytes_invalid=0 send_seq=11429 receive_seq=11429 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998758 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.9 th2: temp=62.4 th3: temp=59.9 sysload=0.16 cputime=511.134 memavail=7389276 print_time=6710.243 buffer_time=2.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 19 Hz
Stats 6686.6: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=31407610 bytes_read=4887099 bytes_retransmit=9 bytes_invalid=0 send_seq=593359 receive_seq=593359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=1995 freq=400016030 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41392 bytes_read=129468 bytes_retransmit=0 bytes_invalid=0 send_seq=6870 receive_seq=6870 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999459 adj=49997310 toolboard_t0: mcu_awake=0.262 mcu_task_avg=0.000116 mcu_task_stddev=0.000070 bytes_write=203944 bytes_read=6561193 bytes_retransmit=9 bytes_invalid=0 send_seq=28459 receive_seq=28459 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997560 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136824 bytes_read=3729918 bytes_retransmit=9 bytes_invalid=0 send_seq=18971 receive_seq=18971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997405 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41659 bytes_read=1707349 bytes_retransmit=9 bytes_invalid=0 send_seq=6884 receive_seq=6884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997590 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42145 bytes_read=126932 bytes_retransmit=9 bytes_invalid=0 send_seq=6871 receive_seq=6871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999421 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96237 bytes_read=2606360 bytes_retransmit=0 bytes_invalid=0 send_seq=11430 receive_seq=11430 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998613 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.9 th2: temp=62.3 th3: temp=59.8 sysload=0.16 cputime=511.237 memavail=7394928 print_time=6711.455 buffer_time=2.212 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 20 Hz
Stats 6687.6: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=31412746 bytes_read=4887905 bytes_retransmit=9 bytes_invalid=0 send_seq=593455 receive_seq=593455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=2556 freq=400016012 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41398 bytes_read=129484 bytes_retransmit=0 bytes_invalid=0 send_seq=6871 receive_seq=6871 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999459 adj=49997385 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=204020 bytes_read=6564255 bytes_retransmit=9 bytes_invalid=0 send_seq=28470 receive_seq=28470 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997636 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136830 bytes_read=3730026 bytes_retransmit=9 bytes_invalid=0 send_seq=18972 receive_seq=18972 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41665 bytes_read=1707623 bytes_retransmit=9 bytes_invalid=0 send_seq=6885 receive_seq=6885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997634 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42151 bytes_read=126948 bytes_retransmit=9 bytes_invalid=0 send_seq=6872 receive_seq=6872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96243 bytes_read=2606716 bytes_retransmit=0 bytes_invalid=0 send_seq=11431 receive_seq=11431 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998708 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.7 th2: temp=62.3 th3: temp=59.7 sysload=0.16 cputime=511.331 memavail=7394172 print_time=6712.325 buffer_time=2.082 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 21 Hz
Stats 6688.6: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=31418675 bytes_read=4888761 bytes_retransmit=9 bytes_invalid=0 send_seq=593565 receive_seq=593565 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=1940 freq=400016007 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41404 bytes_read=129500 bytes_retransmit=0 bytes_invalid=0 send_seq=6872 receive_seq=6872 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999457 adj=49997415 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=204089 bytes_read=6567273 bytes_retransmit=9 bytes_invalid=0 send_seq=28480 receive_seq=28480 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997677 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136836 bytes_read=3730119 bytes_retransmit=9 bytes_invalid=0 send_seq=18973 receive_seq=18973 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41671 bytes_read=1707841 bytes_retransmit=9 bytes_invalid=0 send_seq=6886 receive_seq=6886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42157 bytes_read=126964 bytes_retransmit=9 bytes_invalid=0 send_seq=6873 receive_seq=6873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96249 bytes_read=2607072 bytes_retransmit=0 bytes_invalid=0 send_seq=11432 receive_seq=11432 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998709 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.6 th1: temp=55.9 th2: temp=62.2 th3: temp=59.8 sysload=0.16 cputime=511.429 memavail=7394180 print_time=6713.289 buffer_time=2.046 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 22 Hz
Stats 6689.6: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=31424855 bytes_read=4889670 bytes_retransmit=9 bytes_invalid=0 send_seq=593679 receive_seq=593679 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=22 upcoming_bytes=2847 freq=400016004 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41410 bytes_read=129529 bytes_retransmit=0 bytes_invalid=0 send_seq=6873 receive_seq=6873 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999456 adj=49997411 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=204165 bytes_read=6570398 bytes_retransmit=9 bytes_invalid=0 send_seq=28491 receive_seq=28491 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997670 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136842 bytes_read=3730225 bytes_retransmit=9 bytes_invalid=0 send_seq=18974 receive_seq=18974 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000078 adj=63997557 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41677 bytes_read=1708074 bytes_retransmit=9 bytes_invalid=0 send_seq=6887 receive_seq=6887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42163 bytes_read=126980 bytes_retransmit=9 bytes_invalid=0 send_seq=6874 receive_seq=6874 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96255 bytes_read=2607428 bytes_retransmit=0 bytes_invalid=0 send_seq=11433 receive_seq=11433 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998695 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.9 th2: temp=62.1 th3: temp=59.6 sysload=0.16 cputime=511.536 memavail=7394180 print_time=6714.470 buffer_time=2.226 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 23 Hz
Stats 6690.6: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=31430319 bytes_read=4890495 bytes_retransmit=9 bytes_invalid=0 send_seq=593783 receive_seq=593782 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=3616 freq=400015993 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41416 bytes_read=129545 bytes_retransmit=0 bytes_invalid=0 send_seq=6874 receive_seq=6874 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999455 adj=49997414 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=204241 bytes_read=6573438 bytes_retransmit=9 bytes_invalid=0 send_seq=28502 receive_seq=28502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997664 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136848 bytes_read=3730331 bytes_retransmit=9 bytes_invalid=0 send_seq=18975 receive_seq=18975 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000080 adj=63997676 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41683 bytes_read=1708348 bytes_retransmit=9 bytes_invalid=0 send_seq=6888 receive_seq=6888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42169 bytes_read=126996 bytes_retransmit=9 bytes_invalid=0 send_seq=6875 receive_seq=6875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96261 bytes_read=2607784 bytes_retransmit=0 bytes_invalid=0 send_seq=11434 receive_seq=11434 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998686 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.9 th2: temp=62.1 th3: temp=59.6 sysload=0.15 cputime=511.631 memavail=7393956 print_time=6715.335 buffer_time=2.090 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 24 Hz
Stats 6691.6: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=31436634 bytes_read=4891390 bytes_retransmit=9 bytes_invalid=0 send_seq=593899 receive_seq=593899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=3015 freq=400016025 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41422 bytes_read=129561 bytes_retransmit=0 bytes_invalid=0 send_seq=6875 receive_seq=6875 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999453 adj=49997420 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=204317 bytes_read=6576484 bytes_retransmit=9 bytes_invalid=0 send_seq=28513 receive_seq=28513 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997673 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136854 bytes_read=3730442 bytes_retransmit=9 bytes_invalid=0 send_seq=18976 receive_seq=18976 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000078 adj=63997707 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41689 bytes_read=1708566 bytes_retransmit=9 bytes_invalid=0 send_seq=6889 receive_seq=6889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42175 bytes_read=127023 bytes_retransmit=9 bytes_invalid=0 send_seq=6876 receive_seq=6876 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96267 bytes_read=2608140 bytes_retransmit=0 bytes_invalid=0 send_seq=11435 receive_seq=11435 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998691 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.9 th2: temp=62.1 th3: temp=59.6 sysload=0.15 cputime=511.732 memavail=7393972 print_time=6716.298 buffer_time=2.052 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 25 Hz
Stats 6692.6: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=31443485 bytes_read=4892365 bytes_retransmit=9 bytes_invalid=0 send_seq=594023 receive_seq=594023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=4171 freq=400016020 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41428 bytes_read=129577 bytes_retransmit=0 bytes_invalid=0 send_seq=6876 receive_seq=6876 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999452 adj=49997361 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=204393 bytes_read=6579586 bytes_retransmit=9 bytes_invalid=0 send_seq=28524 receive_seq=28524 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997595 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136860 bytes_read=3730570 bytes_retransmit=9 bytes_invalid=0 send_seq=18977 receive_seq=18977 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000078 adj=63997581 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41695 bytes_read=1708788 bytes_retransmit=9 bytes_invalid=0 send_seq=6890 receive_seq=6890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997601 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42181 bytes_read=127039 bytes_retransmit=9 bytes_invalid=0 send_seq=6877 receive_seq=6877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96273 bytes_read=2608496 bytes_retransmit=0 bytes_invalid=0 send_seq=11436 receive_seq=11436 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998645 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.9 th2: temp=62.1 th3: temp=59.5 sysload=0.15 cputime=511.842 memavail=7393972 print_time=6717.512 buffer_time=2.266 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 26 Hz
Stats 6693.6: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=31449542 bytes_read=4893240 bytes_retransmit=9 bytes_invalid=0 send_seq=594136 receive_seq=594136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=4591 freq=400016010 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41434 bytes_read=129593 bytes_retransmit=0 bytes_invalid=0 send_seq=6877 receive_seq=6877 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999451 adj=49997377 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=204469 bytes_read=6582644 bytes_retransmit=9 bytes_invalid=0 send_seq=28535 receive_seq=28535 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997630 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136866 bytes_read=3730670 bytes_retransmit=9 bytes_invalid=0 send_seq=18978 receive_seq=18978 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000076 adj=63997569 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41701 bytes_read=1709082 bytes_retransmit=9 bytes_invalid=0 send_seq=6891 receive_seq=6891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997611 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42187 bytes_read=127055 bytes_retransmit=9 bytes_invalid=0 send_seq=6878 receive_seq=6878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96279 bytes_read=2608852 bytes_retransmit=0 bytes_invalid=0 send_seq=11437 receive_seq=11437 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998647 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.0 th1: temp=55.9 th2: temp=61.9 th3: temp=59.4 sysload=0.15 cputime=511.941 memavail=7393972 print_time=6718.380 buffer_time=2.133 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 27 Hz
Stats 6694.6: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=31456337 bytes_read=4894169 bytes_retransmit=9 bytes_invalid=0 send_seq=594257 receive_seq=594257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=4392 freq=400015989 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41440 bytes_read=129622 bytes_retransmit=0 bytes_invalid=0 send_seq=6878 receive_seq=6878 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999451 adj=49997393 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=204545 bytes_read=6585702 bytes_retransmit=9 bytes_invalid=0 send_seq=28546 receive_seq=28546 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997646 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136872 bytes_read=3730770 bytes_retransmit=9 bytes_invalid=0 send_seq=18979 receive_seq=18979 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000075 adj=63997564 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41707 bytes_read=1709331 bytes_retransmit=9 bytes_invalid=0 send_seq=6892 receive_seq=6892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42193 bytes_read=127071 bytes_retransmit=9 bytes_invalid=0 send_seq=6879 receive_seq=6879 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96285 bytes_read=2609208 bytes_retransmit=0 bytes_invalid=0 send_seq=11438 receive_seq=11438 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998659 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.6 th1: temp=55.9 th2: temp=62.0 th3: temp=59.5 sysload=0.15 cputime=512.044 memavail=7393972 print_time=6719.350 buffer_time=2.102 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 28 Hz
Stats 6695.6: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=31463596 bytes_read=4895134 bytes_retransmit=9 bytes_invalid=0 send_seq=594385 receive_seq=594385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=5776 freq=400015984 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41446 bytes_read=129638 bytes_retransmit=0 bytes_invalid=0 send_seq=6879 receive_seq=6879 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999450 adj=49997429 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=204621 bytes_read=6588786 bytes_retransmit=9 bytes_invalid=0 send_seq=28557 receive_seq=28557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997697 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=136878 bytes_read=3730898 bytes_retransmit=9 bytes_invalid=0 send_seq=18980 receive_seq=18980 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000086 adj=63997579 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41713 bytes_read=1709565 bytes_retransmit=9 bytes_invalid=0 send_seq=6893 receive_seq=6893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42199 bytes_read=127087 bytes_retransmit=9 bytes_invalid=0 send_seq=6880 receive_seq=6880 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96291 bytes_read=2609564 bytes_retransmit=0 bytes_invalid=0 send_seq=11439 receive_seq=11439 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998672 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.9 th2: temp=62.1 th3: temp=59.4 sysload=0.14 cputime=512.152 memavail=7393972 print_time=6720.569 buffer_time=2.320 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 29 Hz
Stats 6696.6: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=31469819 bytes_read=4896024 bytes_retransmit=9 bytes_invalid=0 send_seq=594501 receive_seq=594501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=5620 freq=400016096 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41452 bytes_read=129654 bytes_retransmit=0 bytes_invalid=0 send_seq=6880 receive_seq=6880 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999450 adj=49997437 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=204697 bytes_read=6591901 bytes_retransmit=9 bytes_invalid=0 send_seq=28568 receive_seq=28568 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000266 adj=63997947 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136884 bytes_read=3731012 bytes_retransmit=9 bytes_invalid=0 send_seq=18981 receive_seq=18981 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000084 adj=63997700 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41719 bytes_read=1709859 bytes_retransmit=9 bytes_invalid=0 send_seq=6894 receive_seq=6894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42205 bytes_read=127114 bytes_retransmit=9 bytes_invalid=0 send_seq=6881 receive_seq=6881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96297 bytes_read=2609920 bytes_retransmit=0 bytes_invalid=0 send_seq=11440 receive_seq=11440 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998669 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.5 th1: temp=56.0 th2: temp=61.9 th3: temp=59.3 sysload=0.14 cputime=512.250 memavail=7393972 print_time=6721.441 buffer_time=2.192 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 30 Hz
Stats 6697.6: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31476985 bytes_read=4897019 bytes_retransmit=9 bytes_invalid=0 send_seq=594632 receive_seq=594632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=5544 freq=400016149 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41458 bytes_read=129670 bytes_retransmit=0 bytes_invalid=0 send_seq=6881 receive_seq=6881 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999449 adj=49997258 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=204773 bytes_read=6594974 bytes_retransmit=9 bytes_invalid=0 send_seq=28579 receive_seq=28579 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000279 adj=63998079 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136890 bytes_read=3731112 bytes_retransmit=9 bytes_invalid=0 send_seq=18982 receive_seq=18982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000081 adj=63997429 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41725 bytes_read=1710093 bytes_retransmit=9 bytes_invalid=0 send_seq=6895 receive_seq=6895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997490 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42211 bytes_read=127130 bytes_retransmit=9 bytes_invalid=0 send_seq=6882 receive_seq=6882 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999393 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96303 bytes_read=2610276 bytes_retransmit=0 bytes_invalid=0 send_seq=11441 receive_seq=11441 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998556 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.6 th1: temp=55.9 th2: temp=61.9 th3: temp=59.2 sysload=0.14 cputime=512.353 memavail=7393480 print_time=6722.371 buffer_time=2.121 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 31 Hz
Stats 6698.6: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31484811 bytes_read=4898054 bytes_retransmit=9 bytes_invalid=0 send_seq=594774 receive_seq=594774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=6764 freq=400016164 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41464 bytes_read=129686 bytes_retransmit=0 bytes_invalid=0 send_seq=6882 receive_seq=6882 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999448 adj=49997188 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=204849 bytes_read=6598060 bytes_retransmit=9 bytes_invalid=0 send_seq=28590 receive_seq=28590 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000275 adj=63998071 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136896 bytes_read=3731240 bytes_retransmit=9 bytes_invalid=0 send_seq=18983 receive_seq=18983 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000079 adj=63997300 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41731 bytes_read=1710327 bytes_retransmit=9 bytes_invalid=0 send_seq=6896 receive_seq=6896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997421 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42217 bytes_read=127146 bytes_retransmit=9 bytes_invalid=0 send_seq=6883 receive_seq=6883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999378 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96309 bytes_read=2610632 bytes_retransmit=0 bytes_invalid=0 send_seq=11442 receive_seq=11442 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998522 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.8 th2: temp=61.7 th3: temp=59.3 sysload=0.14 cputime=512.465 memavail=7393484 print_time=6723.592 buffer_time=2.342 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 32 Hz
Stats 6699.6: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31491440 bytes_read=4898981 bytes_retransmit=9 bytes_invalid=0 send_seq=594896 receive_seq=594896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=6351 freq=400016240 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41476 bytes_read=129731 bytes_retransmit=0 bytes_invalid=0 send_seq=6884 receive_seq=6884 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999448 adj=49997228 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=204931 bytes_read=6601133 bytes_retransmit=9 bytes_invalid=0 send_seq=28602 receive_seq=28602 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000267 adj=63997884 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136908 bytes_read=3731356 bytes_retransmit=9 bytes_invalid=0 send_seq=18985 receive_seq=18985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000075 adj=63997306 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41743 bytes_read=1710652 bytes_retransmit=9 bytes_invalid=0 send_seq=6898 receive_seq=6898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999566 adj=47997477 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42229 bytes_read=127178 bytes_retransmit=9 bytes_invalid=0 send_seq=6885 receive_seq=6885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999388 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96321 bytes_read=2611004 bytes_retransmit=0 bytes_invalid=0 send_seq=11444 receive_seq=11444 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998542 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.7 th2: temp=61.6 th3: temp=59.4 sysload=0.14 cputime=512.570 memavail=7393484 print_time=6724.476 buffer_time=2.225 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 33 Hz
Stats 6700.6: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31498976 bytes_read=4899975 bytes_retransmit=9 bytes_invalid=0 send_seq=595030 receive_seq=595030 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=6679 freq=400016226 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41482 bytes_read=129747 bytes_retransmit=0 bytes_invalid=0 send_seq=6885 receive_seq=6885 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999450 adj=49997133 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=205007 bytes_read=6604191 bytes_retransmit=9 bytes_invalid=0 send_seq=28613 receive_seq=28613 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000263 adj=63997613 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136914 bytes_read=3731456 bytes_retransmit=9 bytes_invalid=0 send_seq=18986 receive_seq=18986 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997129 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41749 bytes_read=1710886 bytes_retransmit=9 bytes_invalid=0 send_seq=6899 receive_seq=6899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999565 adj=47997443 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42235 bytes_read=127194 bytes_retransmit=9 bytes_invalid=0 send_seq=6886 receive_seq=6886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999363 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96327 bytes_read=2611360 bytes_retransmit=0 bytes_invalid=0 send_seq=11445 receive_seq=11445 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998500 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.9 th2: temp=61.8 th3: temp=59.2 sysload=0.13 cputime=512.678 memavail=7393496 print_time=6725.419 buffer_time=2.167 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.5 pwm=0.000
Testing frequency 34 Hz
Stats 6701.6: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31507082 bytes_read=4901025 bytes_retransmit=9 bytes_invalid=0 send_seq=595175 receive_seq=595175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=4944 freq=400016203 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41488 bytes_read=129763 bytes_retransmit=0 bytes_invalid=0 send_seq=6886 receive_seq=6886 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999448 adj=49997220 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=205083 bytes_read=6607276 bytes_retransmit=9 bytes_invalid=0 send_seq=28624 receive_seq=28624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000259 adj=63997605 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136920 bytes_read=3731598 bytes_retransmit=9 bytes_invalid=0 send_seq=18987 receive_seq=18987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000078 adj=63997184 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41755 bytes_read=1711120 bytes_retransmit=9 bytes_invalid=0 send_seq=6900 receive_seq=6900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997476 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42241 bytes_read=127221 bytes_retransmit=9 bytes_invalid=0 send_seq=6887 receive_seq=6887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999381 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96333 bytes_read=2611716 bytes_retransmit=0 bytes_invalid=0 send_seq=11446 receive_seq=11446 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998536 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.5 th1: temp=56.0 th2: temp=61.7 th3: temp=59.2 sysload=0.13 cputime=512.785 memavail=7393500 print_time=6726.292 buffer_time=2.040 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 35 Hz
Stats 6702.6: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31513992 bytes_read=4901986 bytes_retransmit=9 bytes_invalid=0 send_seq=595302 receive_seq=595302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=7456 freq=400016188 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41494 bytes_read=129779 bytes_retransmit=0 bytes_invalid=0 send_seq=6887 receive_seq=6887 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999448 adj=49997262 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=205152 bytes_read=6610329 bytes_retransmit=9 bytes_invalid=0 send_seq=28634 receive_seq=28634 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000255 adj=63997609 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136926 bytes_read=3731698 bytes_retransmit=9 bytes_invalid=0 send_seq=18988 receive_seq=18988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000076 adj=63997322 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41761 bytes_read=1711414 bytes_retransmit=9 bytes_invalid=0 send_seq=6901 receive_seq=6901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999571 adj=47997519 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42247 bytes_read=127237 bytes_retransmit=9 bytes_invalid=0 send_seq=6888 receive_seq=6888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999396 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96339 bytes_read=2612072 bytes_retransmit=0 bytes_invalid=0 send_seq=11447 receive_seq=11447 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998577 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.6 th1: temp=55.8 th2: temp=61.8 th3: temp=59.3 sysload=0.13 cputime=512.902 memavail=7387956 print_time=6727.483 buffer_time=2.232 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 36 Hz
Stats 6703.6: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31521999 bytes_read=4903030 bytes_retransmit=9 bytes_invalid=0 send_seq=595446 receive_seq=595446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=7844 freq=400016168 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41500 bytes_read=129795 bytes_retransmit=0 bytes_invalid=0 send_seq=6888 receive_seq=6888 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999447 adj=49997329 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=205228 bytes_read=6613385 bytes_retransmit=9 bytes_invalid=0 send_seq=28645 receive_seq=28645 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000251 adj=63997612 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136932 bytes_read=3731798 bytes_retransmit=9 bytes_invalid=0 send_seq=18989 receive_seq=18989 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000074 adj=63997385 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41767 bytes_read=1711648 bytes_retransmit=9 bytes_invalid=0 send_seq=6902 receive_seq=6902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999569 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42253 bytes_read=127253 bytes_retransmit=9 bytes_invalid=0 send_seq=6889 receive_seq=6889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999416 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96345 bytes_read=2612428 bytes_retransmit=0 bytes_invalid=0 send_seq=11448 receive_seq=11448 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998649 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.6 th1: temp=55.8 th2: temp=61.7 th3: temp=59.2 sysload=0.13 cputime=513.011 memavail=7394620 print_time=6728.444 buffer_time=2.192 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 37 Hz
Stats 6704.6: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31530660 bytes_read=4904125 bytes_retransmit=9 bytes_invalid=0 send_seq=595600 receive_seq=595600 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=5980 freq=400016271 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41506 bytes_read=129824 bytes_retransmit=0 bytes_invalid=0 send_seq=6889 receive_seq=6889 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999445 adj=49997360 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=205304 bytes_read=6616531 bytes_retransmit=9 bytes_invalid=0 send_seq=28656 receive_seq=28656 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000248 adj=63997614 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136938 bytes_read=3731926 bytes_retransmit=9 bytes_invalid=0 send_seq=18990 receive_seq=18990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000074 adj=63997415 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41773 bytes_read=1711897 bytes_retransmit=9 bytes_invalid=0 send_seq=6903 receive_seq=6903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999571 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42259 bytes_read=127269 bytes_retransmit=9 bytes_invalid=0 send_seq=6890 receive_seq=6890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96351 bytes_read=2612784 bytes_retransmit=0 bytes_invalid=0 send_seq=11449 receive_seq=11449 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998659 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.8 th2: temp=61.6 th3: temp=59.2 sysload=0.13 cputime=513.120 memavail=7394620 print_time=6729.320 buffer_time=2.067 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 38 Hz
Stats 6705.6: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31538085 bytes_read=4905105 bytes_retransmit=9 bytes_invalid=0 send_seq=595734 receive_seq=595734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=8536 freq=400016230 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41512 bytes_read=129840 bytes_retransmit=0 bytes_invalid=0 send_seq=6890 receive_seq=6890 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999444 adj=49997181 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=205380 bytes_read=6619590 bytes_retransmit=9 bytes_invalid=0 send_seq=28667 receive_seq=28667 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000245 adj=63997361 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136944 bytes_read=3732026 bytes_retransmit=9 bytes_invalid=0 send_seq=18991 receive_seq=18991 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997204 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41779 bytes_read=1712191 bytes_retransmit=9 bytes_invalid=0 send_seq=6904 receive_seq=6904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999570 adj=47997515 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42265 bytes_read=127285 bytes_retransmit=9 bytes_invalid=0 send_seq=6891 receive_seq=6891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999386 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96357 bytes_read=2613140 bytes_retransmit=0 bytes_invalid=0 send_seq=11450 receive_seq=11450 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998545 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.8 th1: temp=55.9 th2: temp=61.6 th3: temp=59.1 sysload=0.12 cputime=513.238 memavail=7394620 print_time=6730.515 buffer_time=2.262 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 39 Hz
Stats 6706.6: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31546530 bytes_read=4906189 bytes_retransmit=9 bytes_invalid=0 send_seq=595886 receive_seq=595886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=8693 freq=400016295 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41518 bytes_read=129856 bytes_retransmit=0 bytes_invalid=0 send_seq=6891 receive_seq=6891 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999444 adj=49997301 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=205456 bytes_read=6622647 bytes_retransmit=9 bytes_invalid=0 send_seq=28678 receive_seq=28678 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000243 adj=63997486 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136950 bytes_read=3732140 bytes_retransmit=9 bytes_invalid=0 send_seq=18992 receive_seq=18992 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997334 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41785 bytes_read=1712425 bytes_retransmit=9 bytes_invalid=0 send_seq=6905 receive_seq=6905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999570 adj=47997595 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42271 bytes_read=127312 bytes_retransmit=9 bytes_invalid=0 send_seq=6892 receive_seq=6892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999416 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96363 bytes_read=2613496 bytes_retransmit=0 bytes_invalid=0 send_seq=11451 receive_seq=11451 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998606 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.2 th2: temp=61.6 th3: temp=59.1 sysload=0.12 cputime=513.348 memavail=7394624 print_time=6731.447 buffer_time=2.192 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 40 Hz
Stats 6707.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31555731 bytes_read=4907330 bytes_retransmit=9 bytes_invalid=0 send_seq=596046 receive_seq=596046 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=6576 freq=400016264 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41524 bytes_read=129872 bytes_retransmit=0 bytes_invalid=0 send_seq=6892 receive_seq=6892 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999444 adj=49997218 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=205532 bytes_read=6625751 bytes_retransmit=9 bytes_invalid=0 send_seq=28689 receive_seq=28689 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997362 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136956 bytes_read=3732268 bytes_retransmit=9 bytes_invalid=0 send_seq=18993 receive_seq=18993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997248 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41791 bytes_read=1712659 bytes_retransmit=9 bytes_invalid=0 send_seq=6906 receive_seq=6906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999569 adj=47997505 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42277 bytes_read=127328 bytes_retransmit=9 bytes_invalid=0 send_seq=6893 receive_seq=6893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999392 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96369 bytes_read=2613852 bytes_retransmit=0 bytes_invalid=0 send_seq=11452 receive_seq=11452 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998547 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.8 th2: temp=61.5 th3: temp=59.2 sysload=0.12 cputime=513.459 memavail=7394400 print_time=6732.338 buffer_time=2.081 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 41 Hz
Stats 6708.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31563458 bytes_read=4908340 bytes_retransmit=9 bytes_invalid=0 send_seq=596186 receive_seq=596186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=8223 freq=400016233 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41530 bytes_read=129887 bytes_retransmit=0 bytes_invalid=0 send_seq=6893 receive_seq=6893 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999444 adj=49997283 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=205608 bytes_read=6628808 bytes_retransmit=9 bytes_invalid=0 send_seq=28700 receive_seq=28700 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997418 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136962 bytes_read=3732368 bytes_retransmit=9 bytes_invalid=0 send_seq=18994 receive_seq=18994 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997310 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41797 bytes_read=1712953 bytes_retransmit=9 bytes_invalid=0 send_seq=6907 receive_seq=6907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999567 adj=47997548 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42283 bytes_read=127344 bytes_retransmit=9 bytes_invalid=0 send_seq=6894 receive_seq=6894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999407 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96375 bytes_read=2614208 bytes_retransmit=0 bytes_invalid=0 send_seq=11453 receive_seq=11453 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998584 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.8 th2: temp=61.5 th3: temp=59.1 sysload=0.12 cputime=513.568 memavail=7394420 print_time=6733.283 buffer_time=2.023 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 42 Hz
Stats 6709.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31572236 bytes_read=4909450 bytes_retransmit=9 bytes_invalid=0 send_seq=596341 receive_seq=596341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=10100 freq=400016197 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41536 bytes_read=129915 bytes_retransmit=0 bytes_invalid=0 send_seq=6894 receive_seq=6894 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999443 adj=49997349 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=205684 bytes_read=6631924 bytes_retransmit=9 bytes_invalid=0 send_seq=28711 receive_seq=28711 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997480 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136968 bytes_read=3732468 bytes_retransmit=9 bytes_invalid=0 send_seq=18995 receive_seq=18995 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997374 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41803 bytes_read=1713202 bytes_retransmit=9 bytes_invalid=0 send_seq=6908 receive_seq=6908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999567 adj=47997589 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42289 bytes_read=127360 bytes_retransmit=9 bytes_invalid=0 send_seq=6895 receive_seq=6895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999420 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96381 bytes_read=2614582 bytes_retransmit=0 bytes_invalid=0 send_seq=11454 receive_seq=11454 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998619 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.6 th1: temp=55.9 th2: temp=61.7 th3: temp=59.1 sysload=0.12 cputime=513.689 memavail=7394420 print_time=6734.473 buffer_time=2.209 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 43 Hz
Stats 6710.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31582005 bytes_read=4910613 bytes_retransmit=9 bytes_invalid=0 send_seq=596512 receive_seq=596512 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=7943 freq=400016170 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41542 bytes_read=129930 bytes_retransmit=0 bytes_invalid=0 send_seq=6895 receive_seq=6895 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999441 adj=49997415 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=205760 bytes_read=6635010 bytes_retransmit=9 bytes_invalid=0 send_seq=28722 receive_seq=28722 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997565 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136974 bytes_read=3732596 bytes_retransmit=9 bytes_invalid=0 send_seq=18996 receive_seq=18996 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997478 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41809 bytes_read=1713451 bytes_retransmit=9 bytes_invalid=0 send_seq=6909 receive_seq=6909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999565 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42295 bytes_read=127376 bytes_retransmit=9 bytes_invalid=0 send_seq=6896 receive_seq=6896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96387 bytes_read=2614938 bytes_retransmit=0 bytes_invalid=0 send_seq=11455 receive_seq=11455 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998651 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.3 th1: temp=55.8 th2: temp=61.5 th3: temp=59.2 sysload=0.11 cputime=513.805 memavail=7394420 print_time=6735.377 buffer_time=2.111 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 44 Hz
Stats 6711.6: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31590477 bytes_read=4911663 bytes_retransmit=9 bytes_invalid=0 send_seq=596660 receive_seq=596660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=8715 freq=400016138 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41548 bytes_read=129945 bytes_retransmit=0 bytes_invalid=0 send_seq=6896 receive_seq=6896 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999441 adj=49997442 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=205836 bytes_read=6638066 bytes_retransmit=9 bytes_invalid=0 send_seq=28733 receive_seq=28733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997602 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136980 bytes_read=3732710 bytes_retransmit=9 bytes_invalid=0 send_seq=18997 receive_seq=18997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997515 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41815 bytes_read=1713730 bytes_retransmit=9 bytes_invalid=0 send_seq=6910 receive_seq=6910 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42301 bytes_read=127403 bytes_retransmit=9 bytes_invalid=0 send_seq=6897 receive_seq=6897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96393 bytes_read=2615294 bytes_retransmit=0 bytes_invalid=0 send_seq=11456 receive_seq=11456 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998673 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.6 th1: temp=55.8 th2: temp=61.4 th3: temp=59.1 sysload=0.11 cputime=513.919 memavail=7394420 print_time=6736.296 buffer_time=2.028 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 45 Hz
Stats 6712.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31599844 bytes_read=4912858 bytes_retransmit=9 bytes_invalid=0 send_seq=596828 receive_seq=596828 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=10588 freq=400016102 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41554 bytes_read=129960 bytes_retransmit=0 bytes_invalid=0 send_seq=6897 receive_seq=6897 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999441 adj=49997483 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=205912 bytes_read=6641140 bytes_retransmit=9 bytes_invalid=0 send_seq=28744 receive_seq=28744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997645 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136986 bytes_read=3732810 bytes_retransmit=9 bytes_invalid=0 send_seq=18998 receive_seq=18998 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997553 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41821 bytes_read=1713964 bytes_retransmit=9 bytes_invalid=0 send_seq=6911 receive_seq=6911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997696 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42307 bytes_read=127419 bytes_retransmit=9 bytes_invalid=0 send_seq=6898 receive_seq=6898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96399 bytes_read=2615650 bytes_retransmit=0 bytes_invalid=0 send_seq=11457 receive_seq=11457 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998694 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.8 th2: temp=61.6 th3: temp=59.1 sysload=0.11 cputime=514.043 memavail=7394420 print_time=6737.501 buffer_time=2.230 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 46 Hz
Stats 6713.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31609527 bytes_read=4914043 bytes_retransmit=9 bytes_invalid=0 send_seq=597003 receive_seq=597003 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=8588 freq=400016088 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41560 bytes_read=129976 bytes_retransmit=0 bytes_invalid=0 send_seq=6898 receive_seq=6898 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999441 adj=49997517 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=205988 bytes_read=6644285 bytes_retransmit=9 bytes_invalid=0 send_seq=28755 receive_seq=28755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997687 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136992 bytes_read=3732938 bytes_retransmit=9 bytes_invalid=0 send_seq=18999 receive_seq=18999 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997602 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=41827 bytes_read=1714228 bytes_retransmit=9 bytes_invalid=0 send_seq=6912 receive_seq=6912 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997713 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42313 bytes_read=127435 bytes_retransmit=9 bytes_invalid=0 send_seq=6899 receive_seq=6899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96405 bytes_read=2616006 bytes_retransmit=0 bytes_invalid=0 send_seq=11458 receive_seq=11458 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998721 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.1 th2: temp=61.5 th3: temp=59.0 sysload=0.11 cputime=514.159 memavail=7394420 print_time=6738.394 buffer_time=2.120 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 47 Hz
Stats 6714.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31618612 bytes_read=4915173 bytes_retransmit=9 bytes_invalid=0 send_seq=597167 receive_seq=597167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=8986 freq=400016053 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41566 bytes_read=130005 bytes_retransmit=0 bytes_invalid=0 send_seq=6899 receive_seq=6899 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999441 adj=49997529 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=206064 bytes_read=6647342 bytes_retransmit=9 bytes_invalid=0 send_seq=28766 receive_seq=28766 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997694 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=136998 bytes_read=3733038 bytes_retransmit=9 bytes_invalid=0 send_seq=19000 receive_seq=19000 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997618 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41833 bytes_read=1714507 bytes_retransmit=9 bytes_invalid=0 send_seq=6913 receive_seq=6913 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997741 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42319 bytes_read=127451 bytes_retransmit=9 bytes_invalid=0 send_seq=6900 receive_seq=6900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999471 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96411 bytes_read=2616362 bytes_retransmit=0 bytes_invalid=0 send_seq=11459 receive_seq=11459 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998723 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.6 th1: temp=55.8 th2: temp=61.4 th3: temp=59.1 sysload=0.11 cputime=514.267 memavail=7394420 print_time=6739.313 buffer_time=2.037 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 48 Hz
Stats 6715.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31627969 bytes_read=4916337 bytes_retransmit=9 bytes_invalid=0 send_seq=597332 receive_seq=597332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=11008 freq=400016030 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41572 bytes_read=130021 bytes_retransmit=0 bytes_invalid=0 send_seq=6900 receive_seq=6900 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999440 adj=49997577 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=206140 bytes_read=6650401 bytes_retransmit=9 bytes_invalid=0 send_seq=28777 receive_seq=28777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997920 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137004 bytes_read=3733138 bytes_retransmit=9 bytes_invalid=0 send_seq=19001 receive_seq=19001 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997652 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41839 bytes_read=1714741 bytes_retransmit=9 bytes_invalid=0 send_seq=6914 receive_seq=6914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997766 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42325 bytes_read=127467 bytes_retransmit=9 bytes_invalid=0 send_seq=6901 receive_seq=6901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999477 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96417 bytes_read=2616718 bytes_retransmit=0 bytes_invalid=0 send_seq=11460 receive_seq=11460 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998744 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.9 th2: temp=61.4 th3: temp=58.9 sysload=0.10 cputime=514.390 memavail=7394420 print_time=6740.515 buffer_time=2.236 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 49 Hz
Stats 6716.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31637875 bytes_read=4917522 bytes_retransmit=9 bytes_invalid=0 send_seq=597507 receive_seq=597507 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=9068 freq=400016014 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41578 bytes_read=130037 bytes_retransmit=0 bytes_invalid=0 send_seq=6901 receive_seq=6901 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999440 adj=49997556 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=206216 bytes_read=6653485 bytes_retransmit=9 bytes_invalid=0 send_seq=28788 receive_seq=28788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997866 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137010 bytes_read=3733280 bytes_retransmit=9 bytes_invalid=0 send_seq=19002 receive_seq=19002 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997721 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41845 bytes_read=1715005 bytes_retransmit=9 bytes_invalid=0 send_seq=6915 receive_seq=6915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999568 adj=47997755 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42331 bytes_read=127494 bytes_retransmit=9 bytes_invalid=0 send_seq=6902 receive_seq=6902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999472 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96423 bytes_read=2617074 bytes_retransmit=0 bytes_invalid=0 send_seq=11461 receive_seq=11461 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998730 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.9 th2: temp=61.4 th3: temp=58.9 sysload=0.10 cputime=514.503 memavail=7394420 print_time=6741.419 buffer_time=2.141 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 50 Hz
Stats 6717.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31647108 bytes_read=4918643 bytes_retransmit=9 bytes_invalid=0 send_seq=597666 receive_seq=597666 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=9735 freq=400016001 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41584 bytes_read=130053 bytes_retransmit=0 bytes_invalid=0 send_seq=6902 receive_seq=6902 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999440 adj=49997572 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=206292 bytes_read=6656558 bytes_retransmit=9 bytes_invalid=0 send_seq=28799 receive_seq=28799 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997861 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137016 bytes_read=3733380 bytes_retransmit=9 bytes_invalid=0 send_seq=19003 receive_seq=19003 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997700 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41851 bytes_read=1715269 bytes_retransmit=9 bytes_invalid=0 send_seq=6916 receive_seq=6916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999567 adj=47997827 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42337 bytes_read=127510 bytes_retransmit=9 bytes_invalid=0 send_seq=6903 receive_seq=6903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999470 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96429 bytes_read=2617430 bytes_retransmit=0 bytes_invalid=0 send_seq=11462 receive_seq=11462 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998734 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.0 th2: temp=61.4 th3: temp=59.1 sysload=0.10 cputime=514.616 memavail=7393632 print_time=6742.323 buffer_time=2.044 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 51 Hz
Stats 6718.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31656577 bytes_read=4919817 bytes_retransmit=9 bytes_invalid=0 send_seq=597833 receive_seq=597833 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=11759 freq=400016004 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41590 bytes_read=130069 bytes_retransmit=0 bytes_invalid=0 send_seq=6903 receive_seq=6903 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999441 adj=49997570 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=206368 bytes_read=6659618 bytes_retransmit=9 bytes_invalid=0 send_seq=28810 receive_seq=28810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997850 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137022 bytes_read=3733480 bytes_retransmit=9 bytes_invalid=0 send_seq=19004 receive_seq=19004 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997690 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41857 bytes_read=1715503 bytes_retransmit=9 bytes_invalid=0 send_seq=6917 receive_seq=6917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999566 adj=47997820 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42343 bytes_read=127526 bytes_retransmit=9 bytes_invalid=0 send_seq=6904 receive_seq=6904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999469 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96435 bytes_read=2617786 bytes_retransmit=0 bytes_invalid=0 send_seq=11463 receive_seq=11463 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998737 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.5 th1: temp=56.0 th2: temp=61.3 th3: temp=59.0 sysload=0.10 cputime=514.740 memavail=7393716 print_time=6743.517 buffer_time=2.238 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 52 Hz
Stats 6719.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31667129 bytes_read=4921057 bytes_retransmit=9 bytes_invalid=0 send_seq=598019 receive_seq=598019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=9459 freq=400016027 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41596 bytes_read=130098 bytes_retransmit=0 bytes_invalid=0 send_seq=6904 receive_seq=6904 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999440 adj=49997536 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=206444 bytes_read=6662702 bytes_retransmit=9 bytes_invalid=0 send_seq=28821 receive_seq=28821 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997776 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137028 bytes_read=3733608 bytes_retransmit=9 bytes_invalid=0 send_seq=19005 receive_seq=19005 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997609 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41863 bytes_read=1715782 bytes_retransmit=9 bytes_invalid=0 send_seq=6918 receive_seq=6918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999566 adj=47997748 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42349 bytes_read=127542 bytes_retransmit=9 bytes_invalid=0 send_seq=6905 receive_seq=6905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96441 bytes_read=2618142 bytes_retransmit=0 bytes_invalid=0 send_seq=11464 receive_seq=11464 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998705 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.6 th1: temp=55.8 th2: temp=61.4 th3: temp=58.9 sysload=0.10 cputime=514.859 memavail=7393232 print_time=6744.423 buffer_time=2.141 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 53 Hz
Stats 6720.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31676651 bytes_read=4922203 bytes_retransmit=9 bytes_invalid=0 send_seq=598187 receive_seq=598187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=10188 freq=400016024 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41602 bytes_read=130114 bytes_retransmit=0 bytes_invalid=0 send_seq=6905 receive_seq=6905 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999439 adj=49997482 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=206520 bytes_read=6665820 bytes_retransmit=9 bytes_invalid=0 send_seq=28832 receive_seq=28832 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997757 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137034 bytes_read=3733708 bytes_retransmit=9 bytes_invalid=0 send_seq=19006 receive_seq=19006 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997528 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41869 bytes_read=1716046 bytes_retransmit=9 bytes_invalid=0 send_seq=6919 receive_seq=6919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997695 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42355 bytes_read=127558 bytes_retransmit=9 bytes_invalid=0 send_seq=6906 receive_seq=6906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96447 bytes_read=2618498 bytes_retransmit=0 bytes_invalid=0 send_seq=11465 receive_seq=11465 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998667 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.5 th1: temp=56.0 th2: temp=61.4 th3: temp=58.9 sysload=0.09 cputime=514.985 memavail=7393856 print_time=6745.322 buffer_time=2.040 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 54 Hz
Stats 6721.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31686379 bytes_read=4923407 bytes_retransmit=9 bytes_invalid=0 send_seq=598360 receive_seq=598360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=35 upcoming_bytes=12581 freq=400016176 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41608 bytes_read=130130 bytes_retransmit=0 bytes_invalid=0 send_seq=6906 receive_seq=6906 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999439 adj=49997471 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=206596 bytes_read=6668876 bytes_retransmit=9 bytes_invalid=0 send_seq=28843 receive_seq=28843 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997727 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137040 bytes_read=3733822 bytes_retransmit=9 bytes_invalid=0 send_seq=19007 receive_seq=19007 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997530 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41875 bytes_read=1716280 bytes_retransmit=9 bytes_invalid=0 send_seq=6920 receive_seq=6920 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42361 bytes_read=127585 bytes_retransmit=9 bytes_invalid=0 send_seq=6907 receive_seq=6907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96453 bytes_read=2618854 bytes_retransmit=0 bytes_invalid=0 send_seq=11466 receive_seq=11466 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998666 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.4 th1: temp=55.9 th2: temp=61.3 th3: temp=58.8 sysload=0.09 cputime=515.114 memavail=7393856 print_time=6746.538 buffer_time=2.255 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 55 Hz
Stats 6722.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31697286 bytes_read=4924698 bytes_retransmit=9 bytes_invalid=0 send_seq=598553 receive_seq=598553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=10015 freq=400016286 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41614 bytes_read=130146 bytes_retransmit=0 bytes_invalid=0 send_seq=6907 receive_seq=6907 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999438 adj=49997223 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=206665 bytes_read=6671957 bytes_retransmit=9 bytes_invalid=0 send_seq=28853 receive_seq=28853 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000251 adj=63997448 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137046 bytes_read=3733950 bytes_retransmit=9 bytes_invalid=0 send_seq=19008 receive_seq=19008 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997222 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41881 bytes_read=1716544 bytes_retransmit=9 bytes_invalid=0 send_seq=6921 receive_seq=6921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997434 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42367 bytes_read=127601 bytes_retransmit=9 bytes_invalid=0 send_seq=6908 receive_seq=6908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999406 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96459 bytes_read=2619210 bytes_retransmit=0 bytes_invalid=0 send_seq=11467 receive_seq=11467 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998516 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.0 th2: temp=61.5 th3: temp=58.9 sysload=0.09 cputime=515.232 memavail=7393856 print_time=6747.439 buffer_time=2.156 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 56 Hz
Stats 6723.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31707137 bytes_read=4925878 bytes_retransmit=9 bytes_invalid=0 send_seq=598728 receive_seq=598727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=10684 freq=400016458 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41620 bytes_read=130162 bytes_retransmit=0 bytes_invalid=0 send_seq=6908 receive_seq=6908 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999437 adj=49997066 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=206741 bytes_read=6675013 bytes_retransmit=9 bytes_invalid=0 send_seq=28864 receive_seq=28864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000247 adj=63997425 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137052 bytes_read=3734050 bytes_retransmit=9 bytes_invalid=0 send_seq=19009 receive_seq=19009 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997020 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41887 bytes_read=1716808 bytes_retransmit=9 bytes_invalid=0 send_seq=6922 receive_seq=6922 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997296 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42373 bytes_read=127617 bytes_retransmit=9 bytes_invalid=0 send_seq=6909 receive_seq=6909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999365 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96465 bytes_read=2619566 bytes_retransmit=0 bytes_invalid=0 send_seq=11468 receive_seq=11468 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998420 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.012 th0: temp=56.6 th1: temp=56.0 th2: temp=61.2 th3: temp=59.0 sysload=0.09 cputime=515.345 memavail=7395624 print_time=6748.339 buffer_time=2.055 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 57 Hz
Stats 6724.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31716915 bytes_read=4927087 bytes_retransmit=9 bytes_invalid=0 send_seq=598901 receive_seq=598901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=13351 freq=400016402 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41626 bytes_read=130191 bytes_retransmit=0 bytes_invalid=0 send_seq=6909 receive_seq=6909 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999436 adj=49996813 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=206817 bytes_read=6678072 bytes_retransmit=9 bytes_invalid=0 send_seq=28875 receive_seq=28875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000245 adj=63997048 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137058 bytes_read=3734150 bytes_retransmit=9 bytes_invalid=0 send_seq=19010 receive_seq=19010 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63996706 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41893 bytes_read=1717057 bytes_retransmit=9 bytes_invalid=0 send_seq=6923 receive_seq=6923 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997053 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42379 bytes_read=127633 bytes_retransmit=9 bytes_invalid=0 send_seq=6910 receive_seq=6910 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999317 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96471 bytes_read=2619922 bytes_retransmit=0 bytes_invalid=0 send_seq=11469 receive_seq=11469 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998262 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.0 th2: temp=61.5 th3: temp=58.8 sysload=0.09 cputime=515.473 memavail=7395372 print_time=6749.548 buffer_time=2.263 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 58 Hz
Stats 6725.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31728151 bytes_read=4928372 bytes_retransmit=9 bytes_invalid=0 send_seq=599096 receive_seq=599096 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=10984 freq=400016391 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41632 bytes_read=130207 bytes_retransmit=0 bytes_invalid=0 send_seq=6910 receive_seq=6910 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999436 adj=49997063 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=206893 bytes_read=6681157 bytes_retransmit=9 bytes_invalid=0 send_seq=28886 receive_seq=28886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000242 adj=63997306 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137064 bytes_read=3734278 bytes_retransmit=9 bytes_invalid=0 send_seq=19011 receive_seq=19011 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997021 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41899 bytes_read=1717336 bytes_retransmit=9 bytes_invalid=0 send_seq=6924 receive_seq=6924 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999565 adj=47997288 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42385 bytes_read=127649 bytes_retransmit=9 bytes_invalid=0 send_seq=6911 receive_seq=6911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999366 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96477 bytes_read=2620278 bytes_retransmit=0 bytes_invalid=0 send_seq=11470 receive_seq=11470 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998420 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.9 th2: temp=61.4 th3: temp=58.9 sysload=0.08 cputime=515.595 memavail=7395148 print_time=6750.467 buffer_time=2.181 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 59 Hz
Stats 6726.6: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31738449 bytes_read=4929592 bytes_retransmit=9 bytes_invalid=0 send_seq=599279 receive_seq=599278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=11372 freq=400016333 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41638 bytes_read=130223 bytes_retransmit=0 bytes_invalid=0 send_seq=6911 receive_seq=6911 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999435 adj=49997118 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=206969 bytes_read=6684272 bytes_retransmit=9 bytes_invalid=0 send_seq=28897 receive_seq=28897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000239 adj=63997331 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=137070 bytes_read=3734392 bytes_retransmit=9 bytes_invalid=0 send_seq=19012 receive_seq=19012 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997083 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41905 bytes_read=1717585 bytes_retransmit=9 bytes_invalid=0 send_seq=6925 receive_seq=6925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997391 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42391 bytes_read=127676 bytes_retransmit=9 bytes_invalid=0 send_seq=6912 receive_seq=6912 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999375 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96483 bytes_read=2620634 bytes_retransmit=0 bytes_invalid=0 send_seq=11471 receive_seq=11471 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998460 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.6 th1: temp=55.7 th2: temp=61.6 th3: temp=58.8 sysload=0.08 cputime=515.712 memavail=7395156 print_time=6751.350 buffer_time=2.065 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 60 Hz
Stats 6727.6: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31748610 bytes_read=4930852 bytes_retransmit=9 bytes_invalid=0 send_seq=599459 receive_seq=599459 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=14020 freq=400016287 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41644 bytes_read=130239 bytes_retransmit=0 bytes_invalid=0 send_seq=6912 receive_seq=6912 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999436 adj=49997242 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=207045 bytes_read=6687348 bytes_retransmit=9 bytes_invalid=0 send_seq=28908 receive_seq=28908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997444 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=137076 bytes_read=3734492 bytes_retransmit=9 bytes_invalid=0 send_seq=19013 receive_seq=19013 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997241 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41911 bytes_read=1717819 bytes_retransmit=9 bytes_invalid=0 send_seq=6926 receive_seq=6926 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997487 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42397 bytes_read=127692 bytes_retransmit=9 bytes_invalid=0 send_seq=6913 receive_seq=6913 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999400 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96489 bytes_read=2620990 bytes_retransmit=0 bytes_invalid=0 send_seq=11472 receive_seq=11472 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998538 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.0 th2: temp=61.3 th3: temp=58.9 sysload=0.08 cputime=515.844 memavail=7394148 print_time=6752.569 buffer_time=2.279 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 61 Hz
Stats 6728.6: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31760060 bytes_read=4932167 bytes_retransmit=9 bytes_invalid=0 send_seq=599660 receive_seq=599660 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=11524 freq=400016246 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41650 bytes_read=130255 bytes_retransmit=0 bytes_invalid=0 send_seq=6913 receive_seq=6913 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999435 adj=49997360 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=207121 bytes_read=6690433 bytes_retransmit=9 bytes_invalid=0 send_seq=28919 receive_seq=28919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997562 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=137082 bytes_read=3734620 bytes_retransmit=9 bytes_invalid=0 send_seq=19014 receive_seq=19014 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997375 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41917 bytes_read=1718098 bytes_retransmit=9 bytes_invalid=0 send_seq=6927 receive_seq=6927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997574 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42403 bytes_read=127708 bytes_retransmit=9 bytes_invalid=0 send_seq=6914 receive_seq=6914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999422 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96495 bytes_read=2621346 bytes_retransmit=0 bytes_invalid=0 send_seq=11473 receive_seq=11473 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998611 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.8 th1: temp=55.9 th2: temp=61.3 th3: temp=58.9 sysload=0.08 cputime=515.967 memavail=7394148 print_time=6753.479 buffer_time=2.189 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 62 Hz
Stats 6729.6: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31770727 bytes_read=4933417 bytes_retransmit=9 bytes_invalid=0 send_seq=599848 receive_seq=599848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=11828 freq=400016208 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=41656 bytes_read=130284 bytes_retransmit=0 bytes_invalid=0 send_seq=6914 receive_seq=6914 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999435 adj=49997420 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=207197 bytes_read=6693490 bytes_retransmit=9 bytes_invalid=0 send_seq=28930 receive_seq=28930 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997616 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=137088 bytes_read=3734720 bytes_retransmit=9 bytes_invalid=0 send_seq=19015 receive_seq=19015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997465 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41923 bytes_read=1718362 bytes_retransmit=9 bytes_invalid=0 send_seq=6928 receive_seq=6928 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42409 bytes_read=127724 bytes_retransmit=9 bytes_invalid=0 send_seq=6915 receive_seq=6915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96501 bytes_read=2621702 bytes_retransmit=0 bytes_invalid=0 send_seq=11474 receive_seq=11474 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998658 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.8 th1: temp=55.9 th2: temp=61.4 th3: temp=58.6 sysload=0.08 cputime=516.085 memavail=7394148 print_time=6754.368 buffer_time=2.078 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 63 Hz
Stats 6730.6: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31780941 bytes_read=4934651 bytes_retransmit=9 bytes_invalid=0 send_seq=600027 receive_seq=600027 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=10979 freq=400016185 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=41662 bytes_read=130300 bytes_retransmit=0 bytes_invalid=0 send_seq=6915 receive_seq=6915 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999435 adj=49997477 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=207273 bytes_read=6696547 bytes_retransmit=9 bytes_invalid=0 send_seq=28941 receive_seq=28941 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997678 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=137094 bytes_read=3734820 bytes_retransmit=9 bytes_invalid=0 send_seq=19016 receive_seq=19016 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997530 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41929 bytes_read=1718596 bytes_retransmit=9 bytes_invalid=0 send_seq=6929 receive_seq=6929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42415 bytes_read=127740 bytes_retransmit=9 bytes_invalid=0 send_seq=6916 receive_seq=6916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96507 bytes_read=2622058 bytes_retransmit=0 bytes_invalid=0 send_seq=11475 receive_seq=11475 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998697 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.9 th2: temp=61.3 th3: temp=58.8 sysload=0.08 cputime=516.207 memavail=7394148 print_time=6755.296 buffer_time=2.006 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 64 Hz
Stats 6731.6: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31792776 bytes_read=4935995 bytes_retransmit=9 bytes_invalid=0 send_seq=600235 receive_seq=600235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=12484 freq=400016157 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=41668 bytes_read=130316 bytes_retransmit=0 bytes_invalid=0 send_seq=6916 receive_seq=6916 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999435 adj=49997502 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=207349 bytes_read=6699634 bytes_retransmit=9 bytes_invalid=0 send_seq=28952 receive_seq=28952 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997714 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137100 bytes_read=3734962 bytes_retransmit=9 bytes_invalid=0 send_seq=19017 receive_seq=19017 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997558 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41935 bytes_read=1718875 bytes_retransmit=9 bytes_invalid=0 send_seq=6930 receive_seq=6930 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42421 bytes_read=127767 bytes_retransmit=9 bytes_invalid=0 send_seq=6917 receive_seq=6917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96513 bytes_read=2622414 bytes_retransmit=0 bytes_invalid=0 send_seq=11476 receive_seq=11476 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998705 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.8 th2: temp=61.5 th3: temp=58.9 sysload=0.08 cputime=516.343 memavail=7394148 print_time=6756.503 buffer_time=2.211 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 65 Hz
Stats 6732.6: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31803788 bytes_read=4937281 bytes_retransmit=9 bytes_invalid=0 send_seq=600427 receive_seq=600427 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=12324 freq=400016129 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=41674 bytes_read=130332 bytes_retransmit=0 bytes_invalid=0 send_seq=6917 receive_seq=6917 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999434 adj=49997516 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=207425 bytes_read=6702709 bytes_retransmit=9 bytes_invalid=0 send_seq=28963 receive_seq=28963 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997728 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137106 bytes_read=3735062 bytes_retransmit=9 bytes_invalid=0 send_seq=19018 receive_seq=19018 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997586 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41941 bytes_read=1719124 bytes_retransmit=9 bytes_invalid=0 send_seq=6931 receive_seq=6931 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997695 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42427 bytes_read=127783 bytes_retransmit=9 bytes_invalid=0 send_seq=6918 receive_seq=6918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999462 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96519 bytes_read=2622770 bytes_retransmit=0 bytes_invalid=0 send_seq=11477 receive_seq=11477 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998711 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.8 th1: temp=55.8 th2: temp=61.3 th3: temp=58.9 sysload=0.08 cputime=516.462 memavail=7394160 print_time=6757.370 buffer_time=2.078 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 66 Hz
Stats 6733.6: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31814223 bytes_read=4938535 bytes_retransmit=9 bytes_invalid=0 send_seq=600610 receive_seq=600610 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=11663 freq=400016103 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=41680 bytes_read=130348 bytes_retransmit=0 bytes_invalid=0 send_seq=6918 receive_seq=6918 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999435 adj=49997546 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=207501 bytes_read=6705824 bytes_retransmit=9 bytes_invalid=0 send_seq=28974 receive_seq=28974 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997745 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137112 bytes_read=3735162 bytes_retransmit=9 bytes_invalid=0 send_seq=19019 receive_seq=19019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997622 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41947 bytes_read=1719358 bytes_retransmit=9 bytes_invalid=0 send_seq=6932 receive_seq=6932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997741 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42433 bytes_read=127799 bytes_retransmit=9 bytes_invalid=0 send_seq=6919 receive_seq=6919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999468 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96525 bytes_read=2623126 bytes_retransmit=0 bytes_invalid=0 send_seq=11478 receive_seq=11478 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998726 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.7 th1: temp=55.8 th2: temp=61.4 th3: temp=58.9 sysload=0.08 cputime=516.585 memavail=7394160 print_time=6758.302 buffer_time=2.011 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 67 Hz
Stats 6734.6: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31826403 bytes_read=4939910 bytes_retransmit=9 bytes_invalid=0 send_seq=600823 receive_seq=600823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=13176 freq=400016068 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41686 bytes_read=130377 bytes_retransmit=0 bytes_invalid=0 send_seq=6919 receive_seq=6919 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999434 adj=49997573 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=207577 bytes_read=6708909 bytes_retransmit=9 bytes_invalid=0 send_seq=28985 receive_seq=28985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997752 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137118 bytes_read=3735290 bytes_retransmit=9 bytes_invalid=0 send_seq=19020 receive_seq=19020 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997641 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41953 bytes_read=1719652 bytes_retransmit=9 bytes_invalid=0 send_seq=6933 receive_seq=6933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997752 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42439 bytes_read=127815 bytes_retransmit=9 bytes_invalid=0 send_seq=6920 receive_seq=6920 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999475 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96531 bytes_read=2623482 bytes_retransmit=0 bytes_invalid=0 send_seq=11479 receive_seq=11479 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998751 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.9 th2: temp=61.5 th3: temp=58.8 sysload=0.08 cputime=516.722 memavail=7394160 print_time=6759.513 buffer_time=2.221 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 68 Hz
Stats 6735.6: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31837769 bytes_read=4941215 bytes_retransmit=9 bytes_invalid=0 send_seq=601022 receive_seq=601022 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=12956 freq=400016045 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41692 bytes_read=130393 bytes_retransmit=0 bytes_invalid=0 send_seq=6920 receive_seq=6920 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999434 adj=49997576 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=207653 bytes_read=6711965 bytes_retransmit=9 bytes_invalid=0 send_seq=28996 receive_seq=28996 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997766 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137124 bytes_read=3735390 bytes_retransmit=9 bytes_invalid=0 send_seq=19021 receive_seq=19021 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997718 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41959 bytes_read=1719901 bytes_retransmit=9 bytes_invalid=0 send_seq=6934 receive_seq=6934 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997757 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42445 bytes_read=127831 bytes_retransmit=9 bytes_invalid=0 send_seq=6921 receive_seq=6921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999474 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96537 bytes_read=2623838 bytes_retransmit=0 bytes_invalid=0 send_seq=11480 receive_seq=11480 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998851 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.0 th2: temp=61.5 th3: temp=58.9 sysload=0.07 cputime=516.841 memavail=7394412 print_time=6760.382 buffer_time=2.089 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 69 Hz
Stats 6736.6: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31848461 bytes_read=4942479 bytes_retransmit=9 bytes_invalid=0 send_seq=601207 receive_seq=601207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=12528 freq=400016024 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41698 bytes_read=130409 bytes_retransmit=0 bytes_invalid=0 send_seq=6921 receive_seq=6921 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999433 adj=49997596 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=207729 bytes_read=6715021 bytes_retransmit=9 bytes_invalid=0 send_seq=29007 receive_seq=29007 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997775 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137130 bytes_read=3735504 bytes_retransmit=9 bytes_invalid=0 send_seq=19022 receive_seq=19022 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997725 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41965 bytes_read=1720135 bytes_retransmit=9 bytes_invalid=0 send_seq=6935 receive_seq=6935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997771 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42451 bytes_read=127858 bytes_retransmit=9 bytes_invalid=0 send_seq=6922 receive_seq=6922 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999481 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96543 bytes_read=2624194 bytes_retransmit=0 bytes_invalid=0 send_seq=11481 receive_seq=11481 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998850 coil_temp=16.9 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=56.6 th1: temp=55.8 th2: temp=61.3 th3: temp=58.9 sysload=0.07 cputime=516.964 memavail=7394412 print_time=6761.319 buffer_time=2.026 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 70 Hz
Stats 6737.6: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31860938 bytes_read=4943895 bytes_retransmit=9 bytes_invalid=0 send_seq=601425 receive_seq=601425 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=13984 freq=400016014 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41704 bytes_read=130425 bytes_retransmit=0 bytes_invalid=0 send_seq=6922 receive_seq=6922 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999434 adj=49997595 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=207805 bytes_read=6718124 bytes_retransmit=9 bytes_invalid=0 send_seq=29018 receive_seq=29018 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997776 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137136 bytes_read=3735632 bytes_retransmit=9 bytes_invalid=0 send_seq=19023 receive_seq=19023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997719 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41971 bytes_read=1720414 bytes_retransmit=9 bytes_invalid=0 send_seq=6936 receive_seq=6936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997771 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42457 bytes_read=127874 bytes_retransmit=9 bytes_invalid=0 send_seq=6923 receive_seq=6923 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999481 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96549 bytes_read=2624550 bytes_retransmit=0 bytes_invalid=0 send_seq=11482 receive_seq=11482 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998846 coil_temp=16.9 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=56.8 th1: temp=55.9 th2: temp=61.3 th3: temp=58.9 sysload=0.07 cputime=517.118 memavail=7393812 print_time=6762.511 buffer_time=2.218 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 71 Hz
Stats 6738.6: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31872713 bytes_read=4945225 bytes_retransmit=9 bytes_invalid=0 send_seq=601629 receive_seq=601629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=13676 freq=400015993 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41710 bytes_read=130441 bytes_retransmit=0 bytes_invalid=0 send_seq=6923 receive_seq=6923 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999435 adj=49997568 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=207881 bytes_read=6721181 bytes_retransmit=9 bytes_invalid=0 send_seq=29029 receive_seq=29029 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997744 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137142 bytes_read=3735732 bytes_retransmit=9 bytes_invalid=0 send_seq=19024 receive_seq=19024 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997659 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=41977 bytes_read=1720663 bytes_retransmit=9 bytes_invalid=0 send_seq=6937 receive_seq=6937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997746 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42463 bytes_read=127890 bytes_retransmit=9 bytes_invalid=0 send_seq=6924 receive_seq=6924 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999470 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96555 bytes_read=2624906 bytes_retransmit=0 bytes_invalid=0 send_seq=11483 receive_seq=11483 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998797 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.8 th1: temp=55.9 th2: temp=61.2 th3: temp=58.9 sysload=0.07 cputime=517.244 memavail=7393812 print_time=6763.396 buffer_time=2.102 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 72 Hz
Stats 6739.6: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31883883 bytes_read=4946539 bytes_retransmit=9 bytes_invalid=0 send_seq=601824 receive_seq=601824 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=13300 freq=400015960 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41716 bytes_read=130470 bytes_retransmit=0 bytes_invalid=0 send_seq=6924 receive_seq=6924 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999434 adj=49997596 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=207957 bytes_read=6724238 bytes_retransmit=9 bytes_invalid=0 send_seq=29040 receive_seq=29040 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997759 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137148 bytes_read=3735832 bytes_retransmit=9 bytes_invalid=0 send_seq=19025 receive_seq=19025 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997670 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41983 bytes_read=1720912 bytes_retransmit=9 bytes_invalid=0 send_seq=6938 receive_seq=6938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997760 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42469 bytes_read=127906 bytes_retransmit=9 bytes_invalid=0 send_seq=6925 receive_seq=6925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999473 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96561 bytes_read=2625262 bytes_retransmit=0 bytes_invalid=0 send_seq=11484 receive_seq=11484 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998807 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=56.5 th1: temp=56.0 th2: temp=61.2 th3: temp=58.9 sysload=0.07 cputime=517.370 memavail=7393816 print_time=6764.336 buffer_time=2.042 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 73 Hz
Stats 6740.6: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31896614 bytes_read=4947954 bytes_retransmit=9 bytes_invalid=0 send_seq=602045 receive_seq=602045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=15259 freq=400015984 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41722 bytes_read=130486 bytes_retransmit=0 bytes_invalid=0 send_seq=6925 receive_seq=6925 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999435 adj=49997621 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=208026 bytes_read=6727301 bytes_retransmit=9 bytes_invalid=0 send_seq=29050 receive_seq=29050 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997795 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137154 bytes_read=3735960 bytes_retransmit=9 bytes_invalid=0 send_seq=19026 receive_seq=19026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997701 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41989 bytes_read=1721206 bytes_retransmit=9 bytes_invalid=0 send_seq=6939 receive_seq=6939 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997790 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42475 bytes_read=127922 bytes_retransmit=9 bytes_invalid=0 send_seq=6926 receive_seq=6926 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999478 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96567 bytes_read=2625618 bytes_retransmit=0 bytes_invalid=0 send_seq=11485 receive_seq=11485 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998805 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=56.7 th1: temp=55.9 th2: temp=61.4 th3: temp=59.0 sysload=0.06 cputime=517.509 memavail=7393816 print_time=6765.543 buffer_time=2.249 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 74 Hz
Stats 6741.6: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31908534 bytes_read=4949304 bytes_retransmit=9 bytes_invalid=0 send_seq=602253 receive_seq=602253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=14448 freq=400015993 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41728 bytes_read=130502 bytes_retransmit=0 bytes_invalid=0 send_seq=6926 receive_seq=6926 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999435 adj=49997539 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=208102 bytes_read=6730415 bytes_retransmit=9 bytes_invalid=0 send_seq=29061 receive_seq=29061 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997812 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137160 bytes_read=3736060 bytes_retransmit=9 bytes_invalid=0 send_seq=19027 receive_seq=19027 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997586 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=41995 bytes_read=1721440 bytes_retransmit=9 bytes_invalid=0 send_seq=6940 receive_seq=6940 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997725 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42481 bytes_read=127949 bytes_retransmit=9 bytes_invalid=0 send_seq=6927 receive_seq=6927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96573 bytes_read=2625974 bytes_retransmit=0 bytes_invalid=0 send_seq=11486 receive_seq=11486 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998733 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=56.9 th1: temp=55.9 th2: temp=61.3 th3: temp=58.8 sysload=0.06 cputime=517.632 memavail=7393816 print_time=6766.416 buffer_time=2.121 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 75 Hz
Stats 6742.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31920030 bytes_read=4950659 bytes_retransmit=9 bytes_invalid=0 send_seq=602454 receive_seq=602454 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=14192 freq=400016026 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41734 bytes_read=130518 bytes_retransmit=0 bytes_invalid=0 send_seq=6927 receive_seq=6927 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999434 adj=49997509 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=208178 bytes_read=6733490 bytes_retransmit=9 bytes_invalid=0 send_seq=29072 receive_seq=29072 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997754 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137166 bytes_read=3736174 bytes_retransmit=9 bytes_invalid=0 send_seq=19028 receive_seq=19028 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997600 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42001 bytes_read=1721674 bytes_retransmit=9 bytes_invalid=0 send_seq=6941 receive_seq=6941 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42487 bytes_read=127965 bytes_retransmit=9 bytes_invalid=0 send_seq=6928 receive_seq=6928 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96579 bytes_read=2626330 bytes_retransmit=0 bytes_invalid=0 send_seq=11487 receive_seq=11487 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998710 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=56.7 th1: temp=55.9 th2: temp=61.0 th3: temp=58.9 sysload=0.06 cputime=517.759 memavail=7393816 print_time=6767.342 buffer_time=2.046 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 76 Hz
Stats 6743.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31933139 bytes_read=4952104 bytes_retransmit=9 bytes_invalid=0 send_seq=602681 receive_seq=602681 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=16087 freq=400016068 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41740 bytes_read=130534 bytes_retransmit=0 bytes_invalid=0 send_seq=6928 receive_seq=6928 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999433 adj=49997434 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=208254 bytes_read=6736574 bytes_retransmit=9 bytes_invalid=0 send_seq=29083 receive_seq=29083 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997651 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137172 bytes_read=3736302 bytes_retransmit=9 bytes_invalid=0 send_seq=19029 receive_seq=19029 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997521 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42007 bytes_read=1721968 bytes_retransmit=9 bytes_invalid=0 send_seq=6942 receive_seq=6942 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997630 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42493 bytes_read=127981 bytes_retransmit=9 bytes_invalid=0 send_seq=6929 receive_seq=6929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96585 bytes_read=2626686 bytes_retransmit=0 bytes_invalid=0 send_seq=11488 receive_seq=11488 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998661 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.8 th2: temp=61.3 th3: temp=58.8 sysload=0.06 cputime=517.900 memavail=7395488 print_time=6768.547 buffer_time=2.252 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 77 Hz
Stats 6744.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31945433 bytes_read=4953474 bytes_retransmit=9 bytes_invalid=0 send_seq=602893 receive_seq=602893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=15096 freq=400016071 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41746 bytes_read=130563 bytes_retransmit=0 bytes_invalid=0 send_seq=6929 receive_seq=6929 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999433 adj=49997361 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=208330 bytes_read=6739631 bytes_retransmit=9 bytes_invalid=0 send_seq=29094 receive_seq=29094 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997566 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137178 bytes_read=3736402 bytes_retransmit=9 bytes_invalid=0 send_seq=19030 receive_seq=19030 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997425 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42013 bytes_read=1722217 bytes_retransmit=9 bytes_invalid=0 send_seq=6943 receive_seq=6943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997568 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42499 bytes_read=127997 bytes_retransmit=9 bytes_invalid=0 send_seq=6930 receive_seq=6930 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999423 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96591 bytes_read=2627042 bytes_retransmit=0 bytes_invalid=0 send_seq=11489 receive_seq=11489 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998617 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=57.0 th1: temp=55.9 th2: temp=61.5 th3: temp=58.9 sysload=0.06 cputime=518.025 memavail=7395236 print_time=6769.425 buffer_time=2.129 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 78 Hz
Stats 6745.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31957133 bytes_read=4954833 bytes_retransmit=9 bytes_invalid=0 send_seq=603097 receive_seq=603097 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=15209 freq=400016047 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41752 bytes_read=130579 bytes_retransmit=0 bytes_invalid=0 send_seq=6930 receive_seq=6930 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999433 adj=49997365 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=208406 bytes_read=6742687 bytes_retransmit=9 bytes_invalid=0 send_seq=29105 receive_seq=29105 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997563 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137184 bytes_read=3736502 bytes_retransmit=9 bytes_invalid=0 send_seq=19031 receive_seq=19031 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997426 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42019 bytes_read=1722451 bytes_retransmit=9 bytes_invalid=0 send_seq=6944 receive_seq=6944 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997562 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42505 bytes_read=128013 bytes_retransmit=9 bytes_invalid=0 send_seq=6931 receive_seq=6931 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96597 bytes_read=2627398 bytes_retransmit=0 bytes_invalid=0 send_seq=11490 receive_seq=11490 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998618 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.1 th2: temp=61.4 th3: temp=58.9 sysload=0.06 cputime=518.154 memavail=7395236 print_time=6770.356 buffer_time=2.060 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 79 Hz
Stats 6746.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31970671 bytes_read=4956313 bytes_retransmit=9 bytes_invalid=0 send_seq=603331 receive_seq=603331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=16635 freq=400016027 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41758 bytes_read=130595 bytes_retransmit=0 bytes_invalid=0 send_seq=6931 receive_seq=6931 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999433 adj=49997407 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=208482 bytes_read=6745773 bytes_retransmit=9 bytes_invalid=0 send_seq=29116 receive_seq=29116 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997604 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137190 bytes_read=3736630 bytes_retransmit=9 bytes_invalid=0 send_seq=19032 receive_seq=19032 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997483 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42025 bytes_read=1722745 bytes_retransmit=9 bytes_invalid=0 send_seq=6945 receive_seq=6945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997602 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42511 bytes_read=128040 bytes_retransmit=9 bytes_invalid=0 send_seq=6932 receive_seq=6932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96603 bytes_read=2627754 bytes_retransmit=0 bytes_invalid=0 send_seq=11491 receive_seq=11491 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998650 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.5 th1: temp=56.0 th2: temp=61.3 th3: temp=58.9 sysload=0.06 cputime=518.298 memavail=7395236 print_time=6771.560 buffer_time=2.264 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 80 Hz
Stats 6747.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31983312 bytes_read=4957729 bytes_retransmit=9 bytes_invalid=0 send_seq=603549 receive_seq=603549 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=15212 freq=400016000 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41764 bytes_read=130611 bytes_retransmit=0 bytes_invalid=0 send_seq=6932 receive_seq=6932 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999432 adj=49997438 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=208558 bytes_read=6748847 bytes_retransmit=9 bytes_invalid=0 send_seq=29127 receive_seq=29127 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997636 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137196 bytes_read=3736744 bytes_retransmit=9 bytes_invalid=0 send_seq=19033 receive_seq=19033 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997512 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42031 bytes_read=1722979 bytes_retransmit=9 bytes_invalid=0 send_seq=6946 receive_seq=6946 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997632 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42517 bytes_read=128056 bytes_retransmit=9 bytes_invalid=0 send_seq=6933 receive_seq=6933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96609 bytes_read=2628110 bytes_retransmit=0 bytes_invalid=0 send_seq=11492 receive_seq=11492 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998666 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.9 th2: temp=61.5 th3: temp=58.9 sysload=0.06 cputime=518.426 memavail=7397972 print_time=6772.430 buffer_time=2.133 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 81 Hz
Stats 6748.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=31995058 bytes_read=4959083 bytes_retransmit=9 bytes_invalid=0 send_seq=603752 receive_seq=603752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=15824 freq=400015981 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41770 bytes_read=130627 bytes_retransmit=0 bytes_invalid=0 send_seq=6933 receive_seq=6933 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999432 adj=49997478 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=208634 bytes_read=6751903 bytes_retransmit=9 bytes_invalid=0 send_seq=29138 receive_seq=29138 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997807 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137202 bytes_read=3736844 bytes_retransmit=9 bytes_invalid=0 send_seq=19034 receive_seq=19034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997556 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42037 bytes_read=1723213 bytes_retransmit=9 bytes_invalid=0 send_seq=6947 receive_seq=6947 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997677 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42523 bytes_read=128072 bytes_retransmit=9 bytes_invalid=0 send_seq=6934 receive_seq=6934 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96615 bytes_read=2628466 bytes_retransmit=0 bytes_invalid=0 send_seq=11493 receive_seq=11493 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998681 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.0 th2: temp=61.4 th3: temp=59.1 sysload=0.06 cputime=518.555 memavail=7397824 print_time=6773.367 buffer_time=2.070 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 82 Hz
Stats 6749.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32008652 bytes_read=4960568 bytes_retransmit=9 bytes_invalid=0 send_seq=603987 receive_seq=603987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=17709 freq=400015959 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41776 bytes_read=130656 bytes_retransmit=0 bytes_invalid=0 send_seq=6934 receive_seq=6934 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999432 adj=49997500 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=208710 bytes_read=6755047 bytes_retransmit=9 bytes_invalid=0 send_seq=29149 receive_seq=29149 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997883 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137208 bytes_read=3736972 bytes_retransmit=9 bytes_invalid=0 send_seq=19035 receive_seq=19035 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997575 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42043 bytes_read=1723522 bytes_retransmit=9 bytes_invalid=0 send_seq=6948 receive_seq=6948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42529 bytes_read=128088 bytes_retransmit=9 bytes_invalid=0 send_seq=6935 receive_seq=6935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999462 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96621 bytes_read=2628822 bytes_retransmit=0 bytes_invalid=0 send_seq=11494 receive_seq=11494 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998691 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.0 th2: temp=61.3 th3: temp=58.8 sysload=0.06 cputime=518.699 memavail=7397824 print_time=6774.572 buffer_time=2.275 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 83 Hz
Stats 6750.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32021643 bytes_read=4961998 bytes_retransmit=9 bytes_invalid=0 send_seq=604211 receive_seq=604211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=15725 freq=400015956 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41782 bytes_read=130672 bytes_retransmit=0 bytes_invalid=0 send_seq=6935 receive_seq=6935 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999432 adj=49997509 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=208786 bytes_read=6758106 bytes_retransmit=9 bytes_invalid=0 send_seq=29160 receive_seq=29160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997847 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137214 bytes_read=3737072 bytes_retransmit=9 bytes_invalid=0 send_seq=19036 receive_seq=19036 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997690 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42049 bytes_read=1723756 bytes_retransmit=9 bytes_invalid=0 send_seq=6949 receive_seq=6949 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997710 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42535 bytes_read=128104 bytes_retransmit=9 bytes_invalid=0 send_seq=6936 receive_seq=6936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96627 bytes_read=2629162 bytes_retransmit=0 bytes_invalid=0 send_seq=11495 receive_seq=11495 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998697 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.6 th1: temp=55.9 th2: temp=61.3 th3: temp=58.9 sysload=0.05 cputime=518.826 memavail=7397824 print_time=6775.440 buffer_time=2.143 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 84 Hz
Stats 6751.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32033572 bytes_read=4963382 bytes_retransmit=9 bytes_invalid=0 send_seq=604420 receive_seq=604420 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=16208 freq=400015952 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41788 bytes_read=130688 bytes_retransmit=0 bytes_invalid=0 send_seq=6936 receive_seq=6936 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999434 adj=49997510 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=208862 bytes_read=6761163 bytes_retransmit=9 bytes_invalid=0 send_seq=29171 receive_seq=29171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997807 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137220 bytes_read=3737172 bytes_retransmit=9 bytes_invalid=0 send_seq=19037 receive_seq=19037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997666 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42055 bytes_read=1723990 bytes_retransmit=9 bytes_invalid=0 send_seq=6950 receive_seq=6950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997702 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42541 bytes_read=128131 bytes_retransmit=9 bytes_invalid=0 send_seq=6937 receive_seq=6937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96633 bytes_read=2629518 bytes_retransmit=0 bytes_invalid=0 send_seq=11496 receive_seq=11496 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998692 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.0 th2: temp=61.5 th3: temp=58.9 sysload=0.05 cputime=518.958 memavail=7397824 print_time=6776.374 buffer_time=2.076 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 85 Hz
Stats 6752.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32047475 bytes_read=4964910 bytes_retransmit=9 bytes_invalid=0 send_seq=604661 receive_seq=604661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=18315 freq=400015943 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41794 bytes_read=130704 bytes_retransmit=0 bytes_invalid=0 send_seq=6937 receive_seq=6937 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999434 adj=49997530 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=208938 bytes_read=6764265 bytes_retransmit=9 bytes_invalid=0 send_seq=29182 receive_seq=29182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997793 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137226 bytes_read=3737314 bytes_retransmit=9 bytes_invalid=0 send_seq=19038 receive_seq=19038 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997641 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42061 bytes_read=1724284 bytes_retransmit=9 bytes_invalid=0 send_seq=6951 receive_seq=6951 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997736 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42547 bytes_read=128147 bytes_retransmit=9 bytes_invalid=0 send_seq=6938 receive_seq=6938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96639 bytes_read=2629874 bytes_retransmit=0 bytes_invalid=0 send_seq=11497 receive_seq=11497 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998693 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.6 th1: temp=55.8 th2: temp=61.4 th3: temp=59.0 sysload=0.05 cputime=519.106 memavail=7397844 print_time=6777.578 buffer_time=2.279 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 86 Hz
Stats 6753.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32060427 bytes_read=4966347 bytes_retransmit=9 bytes_invalid=0 send_seq=604887 receive_seq=604887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=16723 freq=400015949 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41800 bytes_read=130720 bytes_retransmit=0 bytes_invalid=0 send_seq=6938 receive_seq=6938 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999435 adj=49997513 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=209007 bytes_read=6767298 bytes_retransmit=9 bytes_invalid=0 send_seq=29192 receive_seq=29192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997747 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137232 bytes_read=3737414 bytes_retransmit=9 bytes_invalid=0 send_seq=19039 receive_seq=19039 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997604 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42067 bytes_read=1724518 bytes_retransmit=9 bytes_invalid=0 send_seq=6952 receive_seq=6952 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997714 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42553 bytes_read=128163 bytes_retransmit=9 bytes_invalid=0 send_seq=6939 receive_seq=6939 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96645 bytes_read=2630230 bytes_retransmit=0 bytes_invalid=0 send_seq=11498 receive_seq=11498 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998690 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.7 th1: temp=55.9 th2: temp=61.4 th3: temp=58.9 sysload=0.05 cputime=519.234 memavail=7397844 print_time=6778.456 buffer_time=2.157 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 87 Hz
Stats 6754.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32072839 bytes_read=4967761 bytes_retransmit=9 bytes_invalid=0 send_seq=605102 receive_seq=605102 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=17438 freq=400015934 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41806 bytes_read=130749 bytes_retransmit=0 bytes_invalid=0 send_seq=6939 receive_seq=6939 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999435 adj=49997513 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=209083 bytes_read=6770346 bytes_retransmit=9 bytes_invalid=0 send_seq=29203 receive_seq=29203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997705 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137238 bytes_read=3737510 bytes_retransmit=9 bytes_invalid=0 send_seq=19040 receive_seq=19040 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997579 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42073 bytes_read=1724767 bytes_retransmit=9 bytes_invalid=0 send_seq=6953 receive_seq=6953 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997690 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42559 bytes_read=128179 bytes_retransmit=9 bytes_invalid=0 send_seq=6940 receive_seq=6940 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96651 bytes_read=2630586 bytes_retransmit=0 bytes_invalid=0 send_seq=11499 receive_seq=11499 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998724 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.0 th2: temp=61.5 th3: temp=58.9 sysload=0.05 cputime=519.379 memavail=7390536 print_time=6779.383 buffer_time=2.083 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 88 Hz
Stats 6755.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32087280 bytes_read=4969306 bytes_retransmit=9 bytes_invalid=0 send_seq=605349 receive_seq=605349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=46 upcoming_bytes=18638 freq=400015937 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41812 bytes_read=130765 bytes_retransmit=0 bytes_invalid=0 send_seq=6940 receive_seq=6940 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999435 adj=49997521 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=209159 bytes_read=6773412 bytes_retransmit=9 bytes_invalid=0 send_seq=29214 receive_seq=29214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997805 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137244 bytes_read=3737629 bytes_retransmit=9 bytes_invalid=0 send_seq=19041 receive_seq=19041 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997586 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42079 bytes_read=1725061 bytes_retransmit=9 bytes_invalid=0 send_seq=6954 receive_seq=6954 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997698 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42565 bytes_read=128195 bytes_retransmit=9 bytes_invalid=0 send_seq=6941 receive_seq=6941 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96657 bytes_read=2630942 bytes_retransmit=0 bytes_invalid=0 send_seq=11500 receive_seq=11500 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998723 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.8 th1: temp=55.9 th2: temp=61.3 th3: temp=59.0 sysload=0.05 cputime=519.534 memavail=7396416 print_time=6780.577 buffer_time=2.277 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 89 Hz
Stats 6756.6: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32100899 bytes_read=4970796 bytes_retransmit=9 bytes_invalid=0 send_seq=605586 receive_seq=605585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=16669 freq=400015912 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41818 bytes_read=130781 bytes_retransmit=0 bytes_invalid=0 send_seq=6941 receive_seq=6941 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999437 adj=49997502 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=209235 bytes_read=6776512 bytes_retransmit=9 bytes_invalid=0 send_seq=29225 receive_seq=29225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997744 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137250 bytes_read=3737722 bytes_retransmit=9 bytes_invalid=0 send_seq=19042 receive_seq=19042 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997546 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42085 bytes_read=1725295 bytes_retransmit=9 bytes_invalid=0 send_seq=6955 receive_seq=6955 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997669 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42571 bytes_read=128222 bytes_retransmit=9 bytes_invalid=0 send_seq=6942 receive_seq=6942 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96663 bytes_read=2631298 bytes_retransmit=0 bytes_invalid=0 send_seq=11501 receive_seq=11501 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998712 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.1 th2: temp=61.4 th3: temp=58.9 sysload=0.05 cputime=519.667 memavail=7396416 print_time=6781.454 buffer_time=2.153 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 90 Hz
Stats 6757.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32113279 bytes_read=4972236 bytes_retransmit=9 bytes_invalid=0 send_seq=605802 receive_seq=605802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=17449 freq=400015891 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41824 bytes_read=130797 bytes_retransmit=0 bytes_invalid=0 send_seq=6942 receive_seq=6942 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999436 adj=49997554 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=209311 bytes_read=6779572 bytes_retransmit=9 bytes_invalid=0 send_seq=29236 receive_seq=29236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997763 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=137256 bytes_read=3737829 bytes_retransmit=9 bytes_invalid=0 send_seq=19043 receive_seq=19043 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997593 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42091 bytes_read=1725529 bytes_retransmit=9 bytes_invalid=0 send_seq=6956 receive_seq=6956 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42577 bytes_read=128238 bytes_retransmit=9 bytes_invalid=0 send_seq=6943 receive_seq=6943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999462 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96669 bytes_read=2631654 bytes_retransmit=0 bytes_invalid=0 send_seq=11502 receive_seq=11502 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998724 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.0 th2: temp=61.3 th3: temp=58.9 sysload=0.05 cputime=519.805 memavail=7394692 print_time=6782.391 buffer_time=2.090 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 91 Hz
Stats 6758.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32127795 bytes_read=4973771 bytes_retransmit=9 bytes_invalid=0 send_seq=606047 receive_seq=606047 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=19357 freq=400015873 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41830 bytes_read=130813 bytes_retransmit=0 bytes_invalid=0 send_seq=6943 receive_seq=6943 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999436 adj=49997563 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=209387 bytes_read=6782644 bytes_retransmit=9 bytes_invalid=0 send_seq=29247 receive_seq=29247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997790 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=137262 bytes_read=3737952 bytes_retransmit=9 bytes_invalid=0 send_seq=19044 receive_seq=19044 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997692 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42097 bytes_read=1725823 bytes_retransmit=9 bytes_invalid=0 send_seq=6957 receive_seq=6957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997731 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42583 bytes_read=128254 bytes_retransmit=9 bytes_invalid=0 send_seq=6944 receive_seq=6944 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96675 bytes_read=2632010 bytes_retransmit=0 bytes_invalid=0 send_seq=11503 receive_seq=11503 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998733 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.0 th2: temp=61.4 th3: temp=59.0 sysload=0.05 cputime=519.962 memavail=7396320 print_time=6783.598 buffer_time=2.296 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 92 Hz
Stats 6759.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32141165 bytes_read=4975231 bytes_retransmit=9 bytes_invalid=0 send_seq=606277 receive_seq=606277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=17124 freq=400015857 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41836 bytes_read=130842 bytes_retransmit=0 bytes_invalid=0 send_seq=6944 receive_seq=6944 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999435 adj=49997550 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=209463 bytes_read=6785708 bytes_retransmit=9 bytes_invalid=0 send_seq=29258 receive_seq=29258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997771 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=137268 bytes_read=3738052 bytes_retransmit=9 bytes_invalid=0 send_seq=19045 receive_seq=19045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997669 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42103 bytes_read=1726072 bytes_retransmit=9 bytes_invalid=0 send_seq=6958 receive_seq=6958 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997727 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42589 bytes_read=128270 bytes_retransmit=9 bytes_invalid=0 send_seq=6945 receive_seq=6945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96681 bytes_read=2632366 bytes_retransmit=0 bytes_invalid=0 send_seq=11504 receive_seq=11504 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998748 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.1 th2: temp=61.4 th3: temp=58.9 sysload=0.05 cputime=520.101 memavail=7396124 print_time=6784.474 buffer_time=2.170 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 93 Hz
Stats 6760.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32153620 bytes_read=4976650 bytes_retransmit=9 bytes_invalid=0 send_seq=606493 receive_seq=606493 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=18212 freq=400015857 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41842 bytes_read=130858 bytes_retransmit=0 bytes_invalid=0 send_seq=6945 receive_seq=6945 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999436 adj=49997560 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=209539 bytes_read=6788764 bytes_retransmit=9 bytes_invalid=0 send_seq=29269 receive_seq=29269 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997777 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=137274 bytes_read=3738152 bytes_retransmit=9 bytes_invalid=0 send_seq=19046 receive_seq=19046 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997683 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42109 bytes_read=1726306 bytes_retransmit=9 bytes_invalid=0 send_seq=6959 receive_seq=6959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997735 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42595 bytes_read=128286 bytes_retransmit=9 bytes_invalid=0 send_seq=6946 receive_seq=6946 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96687 bytes_read=2632722 bytes_retransmit=0 bytes_invalid=0 send_seq=11505 receive_seq=11505 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998746 coil_temp=16.9 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.1 th2: temp=61.5 th3: temp=58.9 sysload=0.04 cputime=520.241 memavail=7396124 print_time=6785.399 buffer_time=2.095 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 94 Hz
Stats 6761.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32168344 bytes_read=4978251 bytes_retransmit=9 bytes_invalid=0 send_seq=606749 receive_seq=606749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=29 upcoming_bytes=20075 freq=400015818 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41854 bytes_read=130890 bytes_retransmit=0 bytes_invalid=0 send_seq=6947 receive_seq=6947 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999437 adj=49997557 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=209621 bytes_read=6791864 bytes_retransmit=9 bytes_invalid=0 send_seq=29281 receive_seq=29281 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997759 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=137286 bytes_read=3738296 bytes_retransmit=9 bytes_invalid=0 send_seq=19048 receive_seq=19048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997666 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42121 bytes_read=1726616 bytes_retransmit=9 bytes_invalid=0 send_seq=6961 receive_seq=6961 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997717 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42607 bytes_read=128329 bytes_retransmit=9 bytes_invalid=0 send_seq=6948 receive_seq=6948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96699 bytes_read=2633094 bytes_retransmit=0 bytes_invalid=0 send_seq=11507 receive_seq=11507 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998730 coil_temp=16.9 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=56.7 th1: temp=55.9 th2: temp=61.5 th3: temp=58.9 sysload=0.04 cputime=520.396 memavail=7395872 print_time=6786.602 buffer_time=2.297 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 95 Hz
Stats 6762.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32182122 bytes_read=4979767 bytes_retransmit=9 bytes_invalid=0 send_seq=606987 receive_seq=606987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=17743 freq=400015817 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41860 bytes_read=130906 bytes_retransmit=0 bytes_invalid=0 send_seq=6948 receive_seq=6948 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999436 adj=49997586 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=209697 bytes_read=6794939 bytes_retransmit=9 bytes_invalid=0 send_seq=29292 receive_seq=29292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997781 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137292 bytes_read=3738410 bytes_retransmit=9 bytes_invalid=0 send_seq=19049 receive_seq=19049 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997752 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42127 bytes_read=1726850 bytes_retransmit=9 bytes_invalid=0 send_seq=6962 receive_seq=6962 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997743 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42613 bytes_read=128345 bytes_retransmit=9 bytes_invalid=0 send_seq=6949 receive_seq=6949 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96705 bytes_read=2633450 bytes_retransmit=0 bytes_invalid=0 send_seq=11508 receive_seq=11508 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998744 coil_temp=16.9 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=56.6 th1: temp=55.9 th2: temp=61.5 th3: temp=59.1 sysload=0.04 cputime=520.531 memavail=7395872 print_time=6787.466 buffer_time=2.160 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 96 Hz
Stats 6763.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32194856 bytes_read=4981199 bytes_retransmit=9 bytes_invalid=0 send_seq=607207 receive_seq=607207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=19244 freq=400015886 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41866 bytes_read=130922 bytes_retransmit=0 bytes_invalid=0 send_seq=6949 receive_seq=6949 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999436 adj=49997567 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=209773 bytes_read=6798055 bytes_retransmit=9 bytes_invalid=0 send_seq=29303 receive_seq=29303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997759 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137298 bytes_read=3738510 bytes_retransmit=9 bytes_invalid=0 send_seq=19050 receive_seq=19050 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997715 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42133 bytes_read=1727084 bytes_retransmit=9 bytes_invalid=0 send_seq=6963 receive_seq=6963 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997745 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42619 bytes_read=128361 bytes_retransmit=9 bytes_invalid=0 send_seq=6950 receive_seq=6950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96711 bytes_read=2633806 bytes_retransmit=0 bytes_invalid=0 send_seq=11509 receive_seq=11509 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998742 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.1 th2: temp=61.4 th3: temp=59.0 sysload=0.04 cputime=520.665 memavail=7395892 print_time=6788.412 buffer_time=2.106 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 97 Hz
Stats 6764.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32210034 bytes_read=4982819 bytes_retransmit=9 bytes_invalid=0 send_seq=607469 receive_seq=607469 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=20719 freq=400015876 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41872 bytes_read=130951 bytes_retransmit=0 bytes_invalid=0 send_seq=6950 receive_seq=6950 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999436 adj=49997444 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=209849 bytes_read=6801143 bytes_retransmit=9 bytes_invalid=0 send_seq=29314 receive_seq=29314 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997596 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137304 bytes_read=3738638 bytes_retransmit=9 bytes_invalid=0 send_seq=19051 receive_seq=19051 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42139 bytes_read=1727393 bytes_retransmit=9 bytes_invalid=0 send_seq=6964 receive_seq=6964 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42625 bytes_read=128377 bytes_retransmit=9 bytes_invalid=0 send_seq=6951 receive_seq=6951 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96717 bytes_read=2634162 bytes_retransmit=0 bytes_invalid=0 send_seq=11510 receive_seq=11510 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998652 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.0 th2: temp=61.5 th3: temp=58.9 sysload=0.04 cputime=520.820 memavail=7395892 print_time=6789.609 buffer_time=2.302 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 98 Hz
Stats 6765.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32224207 bytes_read=4984349 bytes_retransmit=9 bytes_invalid=0 send_seq=607713 receive_seq=607713 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=18140 freq=400015880 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41878 bytes_read=130967 bytes_retransmit=0 bytes_invalid=0 send_seq=6951 receive_seq=6951 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999436 adj=49997459 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=209918 bytes_read=6804177 bytes_retransmit=9 bytes_invalid=0 send_seq=29324 receive_seq=29324 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997623 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137310 bytes_read=3738738 bytes_retransmit=9 bytes_invalid=0 send_seq=19052 receive_seq=19052 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42145 bytes_read=1727627 bytes_retransmit=9 bytes_invalid=0 send_seq=6965 receive_seq=6965 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42631 bytes_read=128393 bytes_retransmit=9 bytes_invalid=0 send_seq=6952 receive_seq=6952 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96723 bytes_read=2634518 bytes_retransmit=0 bytes_invalid=0 send_seq=11511 receive_seq=11511 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998663 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.0 th2: temp=61.4 th3: temp=58.9 sysload=0.20 cputime=520.969 memavail=7393140 print_time=6790.481 buffer_time=2.174 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 99 Hz
Stats 6766.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32237122 bytes_read=4985808 bytes_retransmit=9 bytes_invalid=0 send_seq=607937 receive_seq=607937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=19420 freq=400015905 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41884 bytes_read=130983 bytes_retransmit=0 bytes_invalid=0 send_seq=6952 receive_seq=6952 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999436 adj=49997459 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=209994 bytes_read=6807234 bytes_retransmit=9 bytes_invalid=0 send_seq=29335 receive_seq=29335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997644 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137316 bytes_read=3738838 bytes_retransmit=9 bytes_invalid=0 send_seq=19053 receive_seq=19053 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997512 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42151 bytes_read=1727861 bytes_retransmit=9 bytes_invalid=0 send_seq=6966 receive_seq=6966 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42637 bytes_read=128420 bytes_retransmit=9 bytes_invalid=0 send_seq=6953 receive_seq=6953 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96729 bytes_read=2634874 bytes_retransmit=0 bytes_invalid=0 send_seq=11512 receive_seq=11512 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998658 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.2 th2: temp=61.4 th3: temp=58.9 sysload=0.20 cputime=521.106 memavail=7393144 print_time=6791.412 buffer_time=2.104 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 100 Hz
Stats 6767.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32252527 bytes_read=4987459 bytes_retransmit=9 bytes_invalid=0 send_seq=608202 receive_seq=608202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=20936 freq=400015881 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41890 bytes_read=130999 bytes_retransmit=0 bytes_invalid=0 send_seq=6953 receive_seq=6953 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999435 adj=49997412 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=210070 bytes_read=6810337 bytes_retransmit=9 bytes_invalid=0 send_seq=29346 receive_seq=29346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997585 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137322 bytes_read=3738980 bytes_retransmit=9 bytes_invalid=0 send_seq=19054 receive_seq=19054 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997469 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42157 bytes_read=1728155 bytes_retransmit=9 bytes_invalid=0 send_seq=6967 receive_seq=6967 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997603 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42643 bytes_read=128436 bytes_retransmit=9 bytes_invalid=0 send_seq=6954 receive_seq=6954 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96735 bytes_read=2635230 bytes_retransmit=0 bytes_invalid=0 send_seq=11513 receive_seq=11513 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998643 coil_temp=16.9 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.0 th2: temp=61.3 th3: temp=59.1 sysload=0.20 cputime=521.267 memavail=7392388 print_time=6792.612 buffer_time=2.304 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 101 Hz
Stats 6768.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32266693 bytes_read=4988994 bytes_retransmit=9 bytes_invalid=0 send_seq=608447 receive_seq=608447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=18563 freq=400015872 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41896 bytes_read=131015 bytes_retransmit=0 bytes_invalid=0 send_seq=6954 receive_seq=6954 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999435 adj=49997448 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=210146 bytes_read=6813395 bytes_retransmit=9 bytes_invalid=0 send_seq=29357 receive_seq=29357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997743 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137328 bytes_read=3739080 bytes_retransmit=9 bytes_invalid=0 send_seq=19055 receive_seq=19055 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997514 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42163 bytes_read=1728389 bytes_retransmit=9 bytes_invalid=0 send_seq=6968 receive_seq=6968 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42649 bytes_read=128452 bytes_retransmit=9 bytes_invalid=0 send_seq=6955 receive_seq=6955 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96741 bytes_read=2635586 bytes_retransmit=0 bytes_invalid=0 send_seq=11514 receive_seq=11514 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998663 coil_temp=16.9 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.1 th2: temp=61.4 th3: temp=58.9 sysload=0.20 cputime=521.407 memavail=7392392 print_time=6793.486 buffer_time=2.177 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 102 Hz
Stats 6769.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32279930 bytes_read=4990478 bytes_retransmit=9 bytes_invalid=0 send_seq=608676 receive_seq=608676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=19820 freq=400015865 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41902 bytes_read=131044 bytes_retransmit=0 bytes_invalid=0 send_seq=6955 receive_seq=6955 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999435 adj=49997460 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=210222 bytes_read=6816453 bytes_retransmit=9 bytes_invalid=0 send_seq=29368 receive_seq=29368 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997733 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137334 bytes_read=3739180 bytes_retransmit=9 bytes_invalid=0 send_seq=19056 receive_seq=19056 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997572 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42169 bytes_read=1728638 bytes_retransmit=9 bytes_invalid=0 send_seq=6969 receive_seq=6969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42655 bytes_read=128468 bytes_retransmit=9 bytes_invalid=0 send_seq=6956 receive_seq=6956 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96747 bytes_read=2635942 bytes_retransmit=0 bytes_invalid=0 send_seq=11515 receive_seq=11515 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998665 coil_temp=16.9 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=56.6 th1: temp=55.9 th2: temp=61.4 th3: temp=59.0 sysload=0.20 cputime=521.545 memavail=7392168 print_time=6794.421 buffer_time=2.112 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 103 Hz
Stats 6770.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32295352 bytes_read=4992103 bytes_retransmit=9 bytes_invalid=0 send_seq=608939 receive_seq=608939 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=21865 freq=400015878 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41908 bytes_read=131060 bytes_retransmit=0 bytes_invalid=0 send_seq=6956 receive_seq=6956 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999434 adj=49997464 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=210298 bytes_read=6819538 bytes_retransmit=9 bytes_invalid=0 send_seq=29379 receive_seq=29379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997828 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137340 bytes_read=3739308 bytes_retransmit=9 bytes_invalid=0 send_seq=19057 receive_seq=19057 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997586 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42175 bytes_read=1728932 bytes_retransmit=9 bytes_invalid=0 send_seq=6970 receive_seq=6970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42661 bytes_read=128484 bytes_retransmit=9 bytes_invalid=0 send_seq=6957 receive_seq=6957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96753 bytes_read=2636298 bytes_retransmit=0 bytes_invalid=0 send_seq=11516 receive_seq=11516 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998666 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.0 th2: temp=61.4 th3: temp=59.1 sysload=0.18 cputime=521.700 memavail=7392172 print_time=6795.623 buffer_time=2.313 print_stall=0 extruder: target=0 temp=18.5 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 104 Hz
Stats 6771.6: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32309888 bytes_read=4993663 bytes_retransmit=9 bytes_invalid=0 send_seq=609189 receive_seq=609189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=19264 freq=400015863 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41914 bytes_read=131076 bytes_retransmit=0 bytes_invalid=0 send_seq=6957 receive_seq=6957 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999435 adj=49997437 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=210374 bytes_read=6822653 bytes_retransmit=9 bytes_invalid=0 send_seq=29390 receive_seq=29390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997810 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137346 bytes_read=3739408 bytes_retransmit=9 bytes_invalid=0 send_seq=19058 receive_seq=19058 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997562 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42181 bytes_read=1729166 bytes_retransmit=9 bytes_invalid=0 send_seq=6971 receive_seq=6971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997730 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42667 bytes_read=128511 bytes_retransmit=9 bytes_invalid=0 send_seq=6958 receive_seq=6958 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96759 bytes_read=2636654 bytes_retransmit=0 bytes_invalid=0 send_seq=11517 receive_seq=11517 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999948 adj=31998703 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.0 th2: temp=61.2 th3: temp=59.0 sysload=0.18 cputime=521.849 memavail=7387620 print_time=6796.495 buffer_time=2.185 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 105 Hz
Stats 6772.6: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32323177 bytes_read=4995178 bytes_retransmit=9 bytes_invalid=0 send_seq=609421 receive_seq=609421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=20925 freq=400015851 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41920 bytes_read=131092 bytes_retransmit=0 bytes_invalid=0 send_seq=6958 receive_seq=6958 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999435 adj=49997478 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=210450 bytes_read=6825742 bytes_retransmit=9 bytes_invalid=0 send_seq=29401 receive_seq=29401 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997807 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137352 bytes_read=3739522 bytes_retransmit=9 bytes_invalid=0 send_seq=19059 receive_seq=19059 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997572 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42187 bytes_read=1729400 bytes_retransmit=9 bytes_invalid=0 send_seq=6972 receive_seq=6972 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997742 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42673 bytes_read=128527 bytes_retransmit=9 bytes_invalid=0 send_seq=6959 receive_seq=6959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96765 bytes_read=2637010 bytes_retransmit=0 bytes_invalid=0 send_seq=11518 receive_seq=11518 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999949 adj=31998790 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.5 th1: temp=56.0 th2: temp=61.3 th3: temp=59.0 sysload=0.18 cputime=521.996 memavail=7393292 print_time=6797.427 buffer_time=2.116 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 106 Hz
Stats 6773.6: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32339333 bytes_read=4996868 bytes_retransmit=9 bytes_invalid=0 send_seq=609697 receive_seq=609697 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=22385 freq=400015846 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41926 bytes_read=131108 bytes_retransmit=0 bytes_invalid=0 send_seq=6959 receive_seq=6959 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999434 adj=49997487 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=210526 bytes_read=6828813 bytes_retransmit=9 bytes_invalid=0 send_seq=29412 receive_seq=29412 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997810 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137358 bytes_read=3739650 bytes_retransmit=9 bytes_invalid=0 send_seq=19060 receive_seq=19060 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997572 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42193 bytes_read=1729694 bytes_retransmit=9 bytes_invalid=0 send_seq=6973 receive_seq=6973 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997738 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42679 bytes_read=128543 bytes_retransmit=9 bytes_invalid=0 send_seq=6960 receive_seq=6960 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96771 bytes_read=2637366 bytes_retransmit=0 bytes_invalid=0 send_seq=11519 receive_seq=11519 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999948 adj=31998792 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.0 th2: temp=61.2 th3: temp=58.8 sysload=0.18 cputime=522.154 memavail=7393296 print_time=6798.628 buffer_time=2.316 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 107 Hz
Stats 6774.6: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32354281 bytes_read=4998473 bytes_retransmit=9 bytes_invalid=0 send_seq=609957 receive_seq=609957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=19636 freq=400015832 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41932 bytes_read=131137 bytes_retransmit=0 bytes_invalid=0 send_seq=6960 receive_seq=6960 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999433 adj=49997475 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=210602 bytes_read=6831870 bytes_retransmit=9 bytes_invalid=0 send_seq=29423 receive_seq=29423 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997759 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137364 bytes_read=3739750 bytes_retransmit=9 bytes_invalid=0 send_seq=19061 receive_seq=19061 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42199 bytes_read=1729943 bytes_retransmit=9 bytes_invalid=0 send_seq=6974 receive_seq=6974 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997738 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42685 bytes_read=128559 bytes_retransmit=9 bytes_invalid=0 send_seq=6961 receive_seq=6961 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=29.1 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96777 bytes_read=2637722 bytes_retransmit=0 bytes_invalid=0 send_seq=11520 receive_seq=11520 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999947 adj=31998750 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.0 th2: temp=61.5 th3: temp=58.9 sysload=0.18 cputime=522.293 memavail=7393296 print_time=6799.499 buffer_time=2.187 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 108 Hz
Stats 6775.6: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32367752 bytes_read=4999972 bytes_retransmit=9 bytes_invalid=0 send_seq=610189 receive_seq=610189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=21260 freq=400015849 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41938 bytes_read=131153 bytes_retransmit=0 bytes_invalid=0 send_seq=6961 receive_seq=6961 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999432 adj=49997485 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=210678 bytes_read=6834941 bytes_retransmit=9 bytes_invalid=0 send_seq=29434 receive_seq=29434 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997754 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137370 bytes_read=3739850 bytes_retransmit=9 bytes_invalid=0 send_seq=19062 receive_seq=19062 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997573 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42205 bytes_read=1730177 bytes_retransmit=9 bytes_invalid=0 send_seq=6975 receive_seq=6975 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997741 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42691 bytes_read=128575 bytes_retransmit=9 bytes_invalid=0 send_seq=6962 receive_seq=6962 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999461 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96783 bytes_read=2638078 bytes_retransmit=0 bytes_invalid=0 send_seq=11521 receive_seq=11521 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998743 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.3 th2: temp=61.4 th3: temp=58.9 sysload=0.17 cputime=522.431 memavail=7393296 print_time=6800.424 buffer_time=2.111 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 109 Hz
Stats 6776.7: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32384088 bytes_read=5001687 bytes_retransmit=9 bytes_invalid=0 send_seq=610470 receive_seq=610470 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=35 upcoming_bytes=22893 freq=400015833 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41944 bytes_read=131169 bytes_retransmit=0 bytes_invalid=0 send_seq=6962 receive_seq=6962 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999432 adj=49997433 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=210747 bytes_read=6838046 bytes_retransmit=9 bytes_invalid=0 send_seq=29444 receive_seq=29444 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997685 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137376 bytes_read=3739978 bytes_retransmit=9 bytes_invalid=0 send_seq=19063 receive_seq=19063 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997527 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42211 bytes_read=1730455 bytes_retransmit=9 bytes_invalid=0 send_seq=6976 receive_seq=6976 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997712 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42697 bytes_read=128602 bytes_retransmit=9 bytes_invalid=0 send_seq=6963 receive_seq=6963 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96789 bytes_read=2638434 bytes_retransmit=0 bytes_invalid=0 send_seq=11522 receive_seq=11522 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998706 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.0 th2: temp=61.3 th3: temp=59.0 sysload=0.17 cputime=522.589 memavail=7393296 print_time=6801.628 buffer_time=2.309 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 110 Hz
Stats 6777.7: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32399481 bytes_read=5003343 bytes_retransmit=9 bytes_invalid=0 send_seq=610736 receive_seq=610736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=19944 freq=400015825 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41950 bytes_read=131185 bytes_retransmit=0 bytes_invalid=0 send_seq=6963 receive_seq=6963 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999432 adj=49997465 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=210823 bytes_read=6841119 bytes_retransmit=9 bytes_invalid=0 send_seq=29455 receive_seq=29455 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997699 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137382 bytes_read=3740092 bytes_retransmit=9 bytes_invalid=0 send_seq=19064 receive_seq=19064 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997544 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42217 bytes_read=1730673 bytes_retransmit=9 bytes_invalid=0 send_seq=6977 receive_seq=6977 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997712 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42703 bytes_read=128618 bytes_retransmit=9 bytes_invalid=0 send_seq=6964 receive_seq=6964 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96795 bytes_read=2638790 bytes_retransmit=0 bytes_invalid=0 send_seq=11523 receive_seq=11523 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998723 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.0 th2: temp=61.5 th3: temp=59.0 sysload=0.17 cputime=522.732 memavail=7393056 print_time=6802.505 buffer_time=2.185 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 111 Hz
Stats 6778.7: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32413100 bytes_read=5004867 bytes_retransmit=9 bytes_invalid=0 send_seq=610973 receive_seq=610973 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=21688 freq=400015823 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41956 bytes_read=131201 bytes_retransmit=0 bytes_invalid=0 send_seq=6964 receive_seq=6964 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999432 adj=49997472 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=210899 bytes_read=6844189 bytes_retransmit=9 bytes_invalid=0 send_seq=29466 receive_seq=29466 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997707 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137388 bytes_read=3740192 bytes_retransmit=9 bytes_invalid=0 send_seq=19065 receive_seq=19065 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997550 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42223 bytes_read=1730891 bytes_retransmit=9 bytes_invalid=0 send_seq=6978 receive_seq=6978 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997709 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42709 bytes_read=128634 bytes_retransmit=9 bytes_invalid=0 send_seq=6965 receive_seq=6965 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96801 bytes_read=2639146 bytes_retransmit=0 bytes_invalid=0 send_seq=11524 receive_seq=11524 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998708 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.0 th2: temp=61.5 th3: temp=59.0 sysload=0.17 cputime=522.872 memavail=7393072 print_time=6803.430 buffer_time=2.109 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 112 Hz
Stats 6779.7: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32429638 bytes_read=5006592 bytes_retransmit=9 bytes_invalid=0 send_seq=611256 receive_seq=611256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=23136 freq=400015821 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41962 bytes_read=131230 bytes_retransmit=0 bytes_invalid=0 send_seq=6965 receive_seq=6965 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999432 adj=49997476 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=210975 bytes_read=6847263 bytes_retransmit=9 bytes_invalid=0 send_seq=29477 receive_seq=29477 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997690 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137394 bytes_read=3740320 bytes_retransmit=9 bytes_invalid=0 send_seq=19066 receive_seq=19066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997619 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42229 bytes_read=1731180 bytes_retransmit=9 bytes_invalid=0 send_seq=6979 receive_seq=6979 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997698 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42715 bytes_read=128650 bytes_retransmit=9 bytes_invalid=0 send_seq=6966 receive_seq=6966 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96807 bytes_read=2639502 bytes_retransmit=0 bytes_invalid=0 send_seq=11525 receive_seq=11525 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998695 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.0 th2: temp=61.4 th3: temp=59.1 sysload=0.17 cputime=523.034 memavail=7393072 print_time=6804.626 buffer_time=2.305 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 113 Hz
Stats 6780.7: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32445193 bytes_read=5008252 bytes_retransmit=9 bytes_invalid=0 send_seq=611526 receive_seq=611526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=20075 freq=400015806 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41968 bytes_read=131246 bytes_retransmit=0 bytes_invalid=0 send_seq=6966 receive_seq=6966 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999431 adj=49997471 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=211051 bytes_read=6850321 bytes_retransmit=9 bytes_invalid=0 send_seq=29488 receive_seq=29488 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997677 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137400 bytes_read=3740420 bytes_retransmit=9 bytes_invalid=0 send_seq=19067 receive_seq=19067 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997635 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42235 bytes_read=1731398 bytes_retransmit=9 bytes_invalid=0 send_seq=6980 receive_seq=6980 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42721 bytes_read=128666 bytes_retransmit=9 bytes_invalid=0 send_seq=6967 receive_seq=6967 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96813 bytes_read=2639858 bytes_retransmit=0 bytes_invalid=0 send_seq=11526 receive_seq=11526 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998676 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.1 th2: temp=61.4 th3: temp=59.0 sysload=0.24 cputime=523.178 memavail=7393076 print_time=6805.509 buffer_time=2.187 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 114 Hz
Stats 6781.7: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32458814 bytes_read=5009766 bytes_retransmit=9 bytes_invalid=0 send_seq=611761 receive_seq=611761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=22028 freq=400015807 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41974 bytes_read=131262 bytes_retransmit=0 bytes_invalid=0 send_seq=6967 receive_seq=6967 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999430 adj=49997480 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=211120 bytes_read=6853368 bytes_retransmit=9 bytes_invalid=0 send_seq=29498 receive_seq=29498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997694 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137406 bytes_read=3740520 bytes_retransmit=9 bytes_invalid=0 send_seq=19068 receive_seq=19068 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997630 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42241 bytes_read=1731616 bytes_retransmit=9 bytes_invalid=0 send_seq=6981 receive_seq=6981 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997729 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42727 bytes_read=128693 bytes_retransmit=9 bytes_invalid=0 send_seq=6968 receive_seq=6968 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96819 bytes_read=2640214 bytes_retransmit=0 bytes_invalid=0 send_seq=11527 receive_seq=11527 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998675 coil_temp=16.9 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=56.8 th1: temp=55.9 th2: temp=61.5 th3: temp=59.1 sysload=0.24 cputime=523.399 memavail=7393076 print_time=6806.437 buffer_time=2.115 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 115 Hz
Stats 6782.7: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32475379 bytes_read=5011507 bytes_retransmit=9 bytes_invalid=0 send_seq=612044 receive_seq=612044 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=23984 freq=400015808 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41980 bytes_read=131278 bytes_retransmit=0 bytes_invalid=0 send_seq=6968 receive_seq=6968 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999429 adj=49997462 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=211196 bytes_read=6856456 bytes_retransmit=9 bytes_invalid=0 send_seq=29509 receive_seq=29509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997690 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137412 bytes_read=3740662 bytes_retransmit=9 bytes_invalid=0 send_seq=19069 receive_seq=19069 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997595 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42247 bytes_read=1731910 bytes_retransmit=9 bytes_invalid=0 send_seq=6982 receive_seq=6982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997706 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42733 bytes_read=128709 bytes_retransmit=9 bytes_invalid=0 send_seq=6969 receive_seq=6969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96825 bytes_read=2640570 bytes_retransmit=0 bytes_invalid=0 send_seq=11528 receive_seq=11528 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998670 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.3 th2: temp=61.5 th3: temp=58.9 sysload=0.24 cputime=523.562 memavail=7393076 print_time=6807.642 buffer_time=2.317 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 116 Hz
Stats 6783.7: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32491242 bytes_read=5013177 bytes_retransmit=9 bytes_invalid=0 send_seq=612316 receive_seq=612316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=20851 freq=400015806 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41986 bytes_read=131294 bytes_retransmit=0 bytes_invalid=0 send_seq=6969 receive_seq=6969 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999429 adj=49997453 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=211272 bytes_read=6859572 bytes_retransmit=9 bytes_invalid=0 send_seq=29520 receive_seq=29520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997670 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137418 bytes_read=3740762 bytes_retransmit=9 bytes_invalid=0 send_seq=19070 receive_seq=19070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42253 bytes_read=1732144 bytes_retransmit=9 bytes_invalid=0 send_seq=6983 receive_seq=6983 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997694 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42739 bytes_read=128725 bytes_retransmit=9 bytes_invalid=0 send_seq=6970 receive_seq=6970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96831 bytes_read=2640926 bytes_retransmit=0 bytes_invalid=0 send_seq=11529 receive_seq=11529 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998683 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.0 th2: temp=61.5 th3: temp=59.1 sysload=0.24 cputime=523.706 memavail=7393076 print_time=6808.519 buffer_time=2.193 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 117 Hz
Stats 6784.7: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32505280 bytes_read=5014734 bytes_retransmit=9 bytes_invalid=0 send_seq=612560 receive_seq=612560 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=22624 freq=400015803 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=41992 bytes_read=131310 bytes_retransmit=0 bytes_invalid=0 send_seq=6970 receive_seq=6970 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999429 adj=49997457 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=211348 bytes_read=6862643 bytes_retransmit=9 bytes_invalid=0 send_seq=29531 receive_seq=29531 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997660 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137424 bytes_read=3740862 bytes_retransmit=9 bytes_invalid=0 send_seq=19071 receive_seq=19071 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42259 bytes_read=1732393 bytes_retransmit=9 bytes_invalid=0 send_seq=6984 receive_seq=6984 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42745 bytes_read=128741 bytes_retransmit=9 bytes_invalid=0 send_seq=6971 receive_seq=6971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96837 bytes_read=2641282 bytes_retransmit=0 bytes_invalid=0 send_seq=11530 receive_seq=11530 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998700 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.0 th2: temp=61.5 th3: temp=59.1 sysload=0.24 cputime=523.847 memavail=7393076 print_time=6809.443 buffer_time=2.116 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 118 Hz
Stats 6785.7: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32522324 bytes_read=5016496 bytes_retransmit=9 bytes_invalid=0 send_seq=612851 receive_seq=612851 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=24368 freq=400015801 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=41998 bytes_read=131339 bytes_retransmit=0 bytes_invalid=0 send_seq=6971 receive_seq=6971 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999429 adj=49997458 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=211424 bytes_read=6865714 bytes_retransmit=9 bytes_invalid=0 send_seq=29542 receive_seq=29542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997683 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137430 bytes_read=3740990 bytes_retransmit=9 bytes_invalid=0 send_seq=19072 receive_seq=19072 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997527 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42265 bytes_read=1732687 bytes_retransmit=9 bytes_invalid=0 send_seq=6985 receive_seq=6985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997683 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42751 bytes_read=128757 bytes_retransmit=9 bytes_invalid=0 send_seq=6972 receive_seq=6972 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96843 bytes_read=2641638 bytes_retransmit=0 bytes_invalid=0 send_seq=11531 receive_seq=11531 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998690 coil_temp=16.9 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.0 th2: temp=61.4 th3: temp=59.1 sysload=0.22 cputime=524.012 memavail=7393076 print_time=6810.646 buffer_time=2.310 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 119 Hz
Stats 6786.7: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32538556 bytes_read=5018196 bytes_retransmit=9 bytes_invalid=0 send_seq=613129 receive_seq=613129 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=20635 freq=400015813 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42004 bytes_read=131355 bytes_retransmit=0 bytes_invalid=0 send_seq=6972 receive_seq=6972 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999428 adj=49997459 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=211500 bytes_read=6868772 bytes_retransmit=9 bytes_invalid=0 send_seq=29553 receive_seq=29553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997683 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137436 bytes_read=3741090 bytes_retransmit=9 bytes_invalid=0 send_seq=19073 receive_seq=19073 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42271 bytes_read=1732921 bytes_retransmit=9 bytes_invalid=0 send_seq=6986 receive_seq=6986 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42757 bytes_read=128784 bytes_retransmit=9 bytes_invalid=0 send_seq=6973 receive_seq=6973 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96849 bytes_read=2641994 bytes_retransmit=0 bytes_invalid=0 send_seq=11532 receive_seq=11532 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998734 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.0 th2: temp=61.6 th3: temp=59.0 sysload=0.22 cputime=524.163 memavail=7393076 print_time=6811.518 buffer_time=2.181 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 120 Hz
Stats 6787.7: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32552526 bytes_read=5019771 bytes_retransmit=9 bytes_invalid=0 send_seq=613373 receive_seq=613373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=35 upcoming_bytes=22611 freq=400015808 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42010 bytes_read=131371 bytes_retransmit=0 bytes_invalid=0 send_seq=6973 receive_seq=6973 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999428 adj=49997433 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=211576 bytes_read=6871931 bytes_retransmit=9 bytes_invalid=0 send_seq=29564 receive_seq=29564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997646 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137442 bytes_read=3741218 bytes_retransmit=9 bytes_invalid=0 send_seq=19074 receive_seq=19074 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997561 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42277 bytes_read=1733155 bytes_retransmit=9 bytes_invalid=0 send_seq=6987 receive_seq=6987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42763 bytes_read=128800 bytes_retransmit=9 bytes_invalid=0 send_seq=6974 receive_seq=6974 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96855 bytes_read=2642350 bytes_retransmit=0 bytes_invalid=0 send_seq=11533 receive_seq=11533 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998699 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.2 th2: temp=61.5 th3: temp=59.0 sysload=0.22 cputime=524.309 memavail=7393088 print_time=6812.443 buffer_time=2.106 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 121 Hz
Stats 6788.7: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32569526 bytes_read=5021541 bytes_retransmit=9 bytes_invalid=0 send_seq=613665 receive_seq=613665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=24623 freq=400015795 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42016 bytes_read=131387 bytes_retransmit=0 bytes_invalid=0 send_seq=6974 receive_seq=6974 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999427 adj=49997439 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=211652 bytes_read=6874987 bytes_retransmit=9 bytes_invalid=0 send_seq=29575 receive_seq=29575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997662 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137448 bytes_read=3741332 bytes_retransmit=9 bytes_invalid=0 send_seq=19075 receive_seq=19075 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42283 bytes_read=1733449 bytes_retransmit=9 bytes_invalid=0 send_seq=6988 receive_seq=6988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42769 bytes_read=128816 bytes_retransmit=9 bytes_invalid=0 send_seq=6975 receive_seq=6975 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96861 bytes_read=2642706 bytes_retransmit=0 bytes_invalid=0 send_seq=11534 receive_seq=11534 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999947 adj=31998686 coil_temp=16.9 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.1 th2: temp=61.5 th3: temp=59.0 sysload=0.22 cputime=524.479 memavail=7392836 print_time=6813.646 buffer_time=2.304 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 122 Hz
Stats 6789.7: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32585953 bytes_read=5023266 bytes_retransmit=9 bytes_invalid=0 send_seq=613948 receive_seq=613948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=20873 freq=400015811 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42022 bytes_read=131403 bytes_retransmit=0 bytes_invalid=0 send_seq=6975 receive_seq=6975 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999427 adj=49997447 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=211728 bytes_read=6878043 bytes_retransmit=9 bytes_invalid=0 send_seq=29586 receive_seq=29586 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997698 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137454 bytes_read=3741432 bytes_retransmit=9 bytes_invalid=0 send_seq=19076 receive_seq=19076 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42289 bytes_read=1733698 bytes_retransmit=9 bytes_invalid=0 send_seq=6989 receive_seq=6989 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42775 bytes_read=128832 bytes_retransmit=9 bytes_invalid=0 send_seq=6976 receive_seq=6976 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96867 bytes_read=2643062 bytes_retransmit=0 bytes_invalid=0 send_seq=11535 receive_seq=11535 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999948 adj=31998735 coil_temp=16.9 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.1 th2: temp=61.7 th3: temp=59.0 sysload=0.22 cputime=524.638 memavail=7393472 print_time=6814.517 buffer_time=2.174 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 123 Hz
Stats 6790.7: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32599983 bytes_read=5024820 bytes_retransmit=9 bytes_invalid=0 send_seq=614191 receive_seq=614191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=23188 freq=400015807 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42028 bytes_read=131432 bytes_retransmit=0 bytes_invalid=0 send_seq=6976 receive_seq=6976 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999427 adj=49997425 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=211804 bytes_read=6881128 bytes_retransmit=9 bytes_invalid=0 send_seq=29597 receive_seq=29597 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997720 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137460 bytes_read=3741546 bytes_retransmit=9 bytes_invalid=0 send_seq=19077 receive_seq=19077 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42295 bytes_read=1733932 bytes_retransmit=9 bytes_invalid=0 send_seq=6990 receive_seq=6990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42781 bytes_read=128848 bytes_retransmit=9 bytes_invalid=0 send_seq=6977 receive_seq=6977 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96873 bytes_read=2643418 bytes_retransmit=0 bytes_invalid=0 send_seq=11536 receive_seq=11536 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999947 adj=31998725 coil_temp=16.9 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.0 th2: temp=61.4 th3: temp=59.0 sysload=0.20 cputime=524.783 memavail=7393472 print_time=6815.448 buffer_time=2.105 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 124 Hz
Stats 6791.7: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32617238 bytes_read=5026610 bytes_retransmit=9 bytes_invalid=0 send_seq=614487 receive_seq=614487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=25052 freq=400015799 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42034 bytes_read=131448 bytes_retransmit=0 bytes_invalid=0 send_seq=6977 receive_seq=6977 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999427 adj=49997431 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=211880 bytes_read=6884185 bytes_retransmit=9 bytes_invalid=0 send_seq=29608 receive_seq=29608 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997718 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137466 bytes_read=3741660 bytes_retransmit=9 bytes_invalid=0 send_seq=19078 receive_seq=19078 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997512 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42301 bytes_read=1734226 bytes_retransmit=9 bytes_invalid=0 send_seq=6991 receive_seq=6991 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42787 bytes_read=128875 bytes_retransmit=9 bytes_invalid=0 send_seq=6978 receive_seq=6978 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96879 bytes_read=2643774 bytes_retransmit=0 bytes_invalid=0 send_seq=11537 receive_seq=11537 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998710 coil_temp=16.9 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.0 th2: temp=61.4 th3: temp=59.1 sysload=0.20 cputime=524.950 memavail=7395192 print_time=6816.648 buffer_time=2.304 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 125 Hz
Stats 6792.7: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32634018 bytes_read=5028386 bytes_retransmit=9 bytes_invalid=0 send_seq=614777 receive_seq=614777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=21027 freq=400015829 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42040 bytes_read=131464 bytes_retransmit=0 bytes_invalid=0 send_seq=6978 receive_seq=6978 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999426 adj=49997448 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=211956 bytes_read=6887260 bytes_retransmit=9 bytes_invalid=0 send_seq=29619 receive_seq=29619 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997708 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=137472 bytes_read=3741774 bytes_retransmit=9 bytes_invalid=0 send_seq=19079 receive_seq=19079 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997620 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42307 bytes_read=1734460 bytes_retransmit=9 bytes_invalid=0 send_seq=6992 receive_seq=6992 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42793 bytes_read=128891 bytes_retransmit=9 bytes_invalid=0 send_seq=6979 receive_seq=6979 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96885 bytes_read=2644130 bytes_retransmit=0 bytes_invalid=0 send_seq=11538 receive_seq=11538 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998700 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.0 th2: temp=61.6 th3: temp=59.1 sysload=0.20 cputime=525.099 memavail=7395192 print_time=6817.524 buffer_time=2.179 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 126 Hz
Stats 6793.7: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32648245 bytes_read=5029960 bytes_retransmit=9 bytes_invalid=0 send_seq=615024 receive_seq=615024 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=23156 freq=400015827 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42046 bytes_read=131480 bytes_retransmit=0 bytes_invalid=0 send_seq=6979 receive_seq=6979 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999426 adj=49997394 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=212025 bytes_read=6890380 bytes_retransmit=9 bytes_invalid=0 send_seq=29629 receive_seq=29629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997707 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=137478 bytes_read=3741888 bytes_retransmit=9 bytes_invalid=0 send_seq=19080 receive_seq=19080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997534 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42313 bytes_read=1734694 bytes_retransmit=9 bytes_invalid=0 send_seq=6993 receive_seq=6993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42799 bytes_read=128907 bytes_retransmit=9 bytes_invalid=0 send_seq=6980 receive_seq=6980 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96891 bytes_read=2644486 bytes_retransmit=0 bytes_invalid=0 send_seq=11539 receive_seq=11539 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998653 coil_temp=16.9 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.0 th2: temp=61.5 th3: temp=59.1 sysload=0.20 cputime=525.244 memavail=7394716 print_time=6818.453 buffer_time=2.107 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 127 Hz
Stats 6794.7: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32665450 bytes_read=5031745 bytes_retransmit=9 bytes_invalid=0 send_seq=615319 receive_seq=615319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=25167 freq=400015914 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42052 bytes_read=131495 bytes_retransmit=0 bytes_invalid=0 send_seq=6980 receive_seq=6980 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999424 adj=49997402 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=212101 bytes_read=6893436 bytes_retransmit=9 bytes_invalid=0 send_seq=29640 receive_seq=29640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997779 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=137484 bytes_read=3742002 bytes_retransmit=9 bytes_invalid=0 send_seq=19081 receive_seq=19081 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997518 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42319 bytes_read=1735003 bytes_retransmit=9 bytes_invalid=0 send_seq=6994 receive_seq=6994 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42805 bytes_read=128923 bytes_retransmit=9 bytes_invalid=0 send_seq=6981 receive_seq=6981 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96897 bytes_read=2644842 bytes_retransmit=0 bytes_invalid=0 send_seq=11540 receive_seq=11540 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998648 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.1 th2: temp=61.5 th3: temp=59.0 sysload=0.20 cputime=525.413 memavail=7394716 print_time=6819.653 buffer_time=2.307 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 128 Hz
Stats 6795.7: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32682234 bytes_read=5033511 bytes_retransmit=9 bytes_invalid=0 send_seq=615608 receive_seq=615608 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=21271 freq=400015907 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42058 bytes_read=131523 bytes_retransmit=0 bytes_invalid=0 send_seq=6981 receive_seq=6981 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999424 adj=49997274 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=212177 bytes_read=6896493 bytes_retransmit=9 bytes_invalid=0 send_seq=29651 receive_seq=29651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997575 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=137490 bytes_read=3742102 bytes_retransmit=9 bytes_invalid=0 send_seq=19082 receive_seq=19082 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997344 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42325 bytes_read=1735237 bytes_retransmit=9 bytes_invalid=0 send_seq=6995 receive_seq=6995 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997505 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42811 bytes_read=128939 bytes_retransmit=9 bytes_invalid=0 send_seq=6982 receive_seq=6982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999408 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96903 bytes_read=2645198 bytes_retransmit=0 bytes_invalid=0 send_seq=11541 receive_seq=11541 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998560 coil_temp=16.9 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=56.5 th1: temp=55.9 th2: temp=61.6 th3: temp=59.0 sysload=0.18 cputime=525.563 memavail=7394716 print_time=6820.524 buffer_time=2.177 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 129 Hz
Stats 6796.7: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32696479 bytes_read=5035079 bytes_retransmit=9 bytes_invalid=0 send_seq=615857 receive_seq=615857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=23688 freq=400015888 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42064 bytes_read=131538 bytes_retransmit=0 bytes_invalid=0 send_seq=6982 receive_seq=6982 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999423 adj=49997293 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=212253 bytes_read=6899578 bytes_retransmit=9 bytes_invalid=0 send_seq=29662 receive_seq=29662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997592 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=137496 bytes_read=3742216 bytes_retransmit=9 bytes_invalid=0 send_seq=19083 receive_seq=19083 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997358 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42331 bytes_read=1735471 bytes_retransmit=9 bytes_invalid=0 send_seq=6996 receive_seq=6996 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997523 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42817 bytes_read=128966 bytes_retransmit=9 bytes_invalid=0 send_seq=6983 receive_seq=6983 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999413 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96909 bytes_read=2645554 bytes_retransmit=0 bytes_invalid=0 send_seq=11542 receive_seq=11542 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998564 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.1 th2: temp=61.6 th3: temp=59.1 sysload=0.18 cputime=525.710 memavail=7394716 print_time=6821.457 buffer_time=2.109 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 130 Hz
Stats 6797.7: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32713872 bytes_read=5036875 bytes_retransmit=9 bytes_invalid=0 send_seq=616151 receive_seq=616151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=29 upcoming_bytes=25763 freq=400015887 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42070 bytes_read=131553 bytes_retransmit=0 bytes_invalid=0 send_seq=6983 receive_seq=6983 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999425 adj=49997335 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=212329 bytes_read=6902651 bytes_retransmit=9 bytes_invalid=0 send_seq=29673 receive_seq=29673 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997634 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137502 bytes_read=3742344 bytes_retransmit=9 bytes_invalid=0 send_seq=19084 receive_seq=19084 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997401 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42337 bytes_read=1735765 bytes_retransmit=9 bytes_invalid=0 send_seq=6997 receive_seq=6997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997563 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42823 bytes_read=128982 bytes_retransmit=9 bytes_invalid=0 send_seq=6984 receive_seq=6984 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96915 bytes_read=2645910 bytes_retransmit=0 bytes_invalid=0 send_seq=11543 receive_seq=11543 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998588 coil_temp=16.9 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.1 th2: temp=61.4 th3: temp=59.0 sysload=0.18 cputime=525.886 memavail=7393728 print_time=6822.657 buffer_time=2.308 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 131 Hz
Stats 6798.7: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32730925 bytes_read=5038674 bytes_retransmit=9 bytes_invalid=0 send_seq=616446 receive_seq=616446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=21608 freq=400015881 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42076 bytes_read=131568 bytes_retransmit=0 bytes_invalid=0 send_seq=6984 receive_seq=6984 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999424 adj=49997385 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=212405 bytes_read=6905709 bytes_retransmit=9 bytes_invalid=0 send_seq=29684 receive_seq=29684 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997632 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137508 bytes_read=3742444 bytes_retransmit=9 bytes_invalid=0 send_seq=19085 receive_seq=19085 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997425 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42343 bytes_read=1735999 bytes_retransmit=9 bytes_invalid=0 send_seq=6998 receive_seq=6998 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997584 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42829 bytes_read=128998 bytes_retransmit=9 bytes_invalid=0 send_seq=6985 receive_seq=6985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96921 bytes_read=2646266 bytes_retransmit=0 bytes_invalid=0 send_seq=11544 receive_seq=11544 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998631 coil_temp=16.9 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.1 th2: temp=61.5 th3: temp=59.1 sysload=0.18 cputime=526.039 memavail=7393736 print_time=6823.533 buffer_time=2.183 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 132 Hz
Stats 6799.7: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32745235 bytes_read=5040249 bytes_retransmit=9 bytes_invalid=0 send_seq=616696 receive_seq=616696 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=29 upcoming_bytes=24127 freq=400015960 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42082 bytes_read=131583 bytes_retransmit=0 bytes_invalid=0 send_seq=6985 receive_seq=6985 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999423 adj=49997394 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=212481 bytes_read=6908852 bytes_retransmit=9 bytes_invalid=0 send_seq=29695 receive_seq=29695 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997632 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137514 bytes_read=3742572 bytes_retransmit=9 bytes_invalid=0 send_seq=19086 receive_seq=19086 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997465 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42349 bytes_read=1736248 bytes_retransmit=9 bytes_invalid=0 send_seq=6999 receive_seq=6999 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997596 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42835 bytes_read=129014 bytes_retransmit=9 bytes_invalid=0 send_seq=6986 receive_seq=6986 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96927 bytes_read=2646622 bytes_retransmit=0 bytes_invalid=0 send_seq=11545 receive_seq=11545 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998630 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.3 th2: temp=61.6 th3: temp=59.1 sysload=0.18 cputime=526.188 memavail=7393736 print_time=6824.459 buffer_time=2.108 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Stats 6800.7: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32762933 bytes_read=5042074 bytes_retransmit=9 bytes_invalid=0 send_seq=616999 receive_seq=616999 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=18392 freq=400015950 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42088 bytes_read=131612 bytes_retransmit=0 bytes_invalid=0 send_seq=6986 receive_seq=6986 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999423 adj=49997266 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=212557 bytes_read=6911911 bytes_retransmit=9 bytes_invalid=0 send_seq=29706 receive_seq=29706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997462 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137520 bytes_read=3742672 bytes_retransmit=9 bytes_invalid=0 send_seq=19087 receive_seq=19087 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997295 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42355 bytes_read=1736542 bytes_retransmit=9 bytes_invalid=0 send_seq=7000 receive_seq=7000 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997487 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42841 bytes_read=129030 bytes_retransmit=9 bytes_invalid=0 send_seq=6987 receive_seq=6987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999407 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96933 bytes_read=2646978 bytes_retransmit=0 bytes_invalid=0 send_seq=11546 receive_seq=11546 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998544 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.1 th2: temp=61.6 th3: temp=59.1 sysload=0.17 cputime=526.326 memavail=7393736 print_time=6825.107 buffer_time=1.756 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6801.7: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32780149 bytes_read=5043863 bytes_retransmit=9 bytes_invalid=0 send_seq=617292 receive_seq=617292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=2832 freq=400015934 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42094 bytes_read=131628 bytes_retransmit=0 bytes_invalid=0 send_seq=6987 receive_seq=6987 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999421 adj=49997276 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=212633 bytes_read=6914968 bytes_retransmit=9 bytes_invalid=0 send_seq=29717 receive_seq=29717 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997491 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137526 bytes_read=3742772 bytes_retransmit=9 bytes_invalid=0 send_seq=19088 receive_seq=19088 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997322 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42361 bytes_read=1736776 bytes_retransmit=9 bytes_invalid=0 send_seq=7001 receive_seq=7001 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997499 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42847 bytes_read=129057 bytes_retransmit=9 bytes_invalid=0 send_seq=6988 receive_seq=6988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999410 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96939 bytes_read=2647334 bytes_retransmit=0 bytes_invalid=0 send_seq=11547 receive_seq=11547 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998537 coil_temp=16.9 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=56.5 th1: temp=56.0 th2: temp=61.4 th3: temp=59.1 sysload=0.17 cputime=526.419 memavail=7393736 print_time=6825.107 buffer_time=0.756 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
LIS2DW finished 'toolboard_t0' measurements
Stats 6802.7: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32783527 bytes_read=5044559 bytes_retransmit=9 bytes_invalid=0 send_seq=617363 receive_seq=617363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015909 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42100 bytes_read=131644 bytes_retransmit=0 bytes_invalid=0 send_seq=6988 receive_seq=6988 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999422 adj=49997285 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=212750 bytes_read=6917745 bytes_retransmit=9 bytes_invalid=0 send_seq=29732 receive_seq=29732 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997522 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137532 bytes_read=3742914 bytes_retransmit=9 bytes_invalid=0 send_seq=19089 receive_seq=19089 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997340 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42367 bytes_read=1737010 bytes_retransmit=9 bytes_invalid=0 send_seq=7002 receive_seq=7002 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997525 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42853 bytes_read=129073 bytes_retransmit=9 bytes_invalid=0 send_seq=6989 receive_seq=6989 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999416 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96945 bytes_read=2647681 bytes_retransmit=0 bytes_invalid=0 send_seq=11548 receive_seq=11548 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998555 coil_temp=16.9 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.1 th2: temp=61.6 th3: temp=59.2 sysload=0.17 cputime=526.513 memavail=7379120 print_time=6825.107 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Resonances data written to /tmp/resonances_y_125.000_250.000_20.000_t0_mirror.csv file
Probing point (125.000, 250.000, 20.000)
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t1' measurements
toolhead: max_velocity: 600.000000
max_accel: 8379.841000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance testing
Testing frequency 10 Hz
Testing frequency 11 Hz
Testing frequency 12 Hz
Stats 6803.7: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32788908 bytes_read=5045399 bytes_retransmit=9 bytes_invalid=0 send_seq=617469 receive_seq=617469 retransmit_seq=2 srtt=0.001 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015888 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42106 bytes_read=131660 bytes_retransmit=0 bytes_invalid=0 send_seq=6989 receive_seq=6989 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999422 adj=49997336 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=212756 bytes_read=6917845 bytes_retransmit=9 bytes_invalid=0 send_seq=29733 receive_seq=29733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997751 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137659 bytes_read=3743807 bytes_retransmit=9 bytes_invalid=0 send_seq=19103 receive_seq=19103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997391 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42373 bytes_read=1737304 bytes_retransmit=9 bytes_invalid=0 send_seq=7003 receive_seq=7003 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997564 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42859 bytes_read=129089 bytes_retransmit=9 bytes_invalid=0 send_seq=6990 receive_seq=6990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96951 bytes_read=2648026 bytes_retransmit=0 bytes_invalid=0 send_seq=11549 receive_seq=11549 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998573 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=56.5 th1: temp=56.1 th2: temp=61.6 th3: temp=59.1 sysload=0.17 cputime=526.718 memavail=7395908 print_time=6829.271 buffer_time=2.918 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6804.7: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32789520 bytes_read=5045863 bytes_retransmit=9 bytes_invalid=0 send_seq=617497 receive_seq=617497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=0 freq=400015866 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42112 bytes_read=131676 bytes_retransmit=0 bytes_invalid=0 send_seq=6990 receive_seq=6990 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999423 adj=49997454 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=212762 bytes_read=6917945 bytes_retransmit=9 bytes_invalid=0 send_seq=29734 receive_seq=29734 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997703 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137735 bytes_read=3746806 bytes_retransmit=9 bytes_invalid=0 send_seq=19114 receive_seq=19114 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997533 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42379 bytes_read=1737553 bytes_retransmit=9 bytes_invalid=0 send_seq=7004 receive_seq=7004 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42865 bytes_read=129105 bytes_retransmit=9 bytes_invalid=0 send_seq=6991 receive_seq=6991 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96957 bytes_read=2648370 bytes_retransmit=0 bytes_invalid=0 send_seq=11550 receive_seq=11550 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998671 coil_temp=16.9 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.4 th2: temp=61.5 th3: temp=59.1 sysload=0.17 cputime=526.784 memavail=7395916 print_time=6829.492 buffer_time=2.138 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 13 Hz
Stats 6805.7: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32791989 bytes_read=5046473 bytes_retransmit=9 bytes_invalid=0 send_seq=617554 receive_seq=617554 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015843 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42118 bytes_read=131705 bytes_retransmit=0 bytes_invalid=0 send_seq=6991 receive_seq=6991 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999424 adj=49997494 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=212768 bytes_read=6918073 bytes_retransmit=9 bytes_invalid=0 send_seq=29735 receive_seq=29735 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997727 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137811 bytes_read=3749845 bytes_retransmit=9 bytes_invalid=0 send_seq=19125 receive_seq=19125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997558 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42385 bytes_read=1737787 bytes_retransmit=9 bytes_invalid=0 send_seq=7005 receive_seq=7005 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997684 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42871 bytes_read=129121 bytes_retransmit=9 bytes_invalid=0 send_seq=6992 receive_seq=6992 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96963 bytes_read=2648715 bytes_retransmit=0 bytes_invalid=0 send_seq=11551 receive_seq=11551 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998678 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.1 th2: temp=61.6 th3: temp=59.0 sysload=0.16 cputime=526.862 memavail=7395916 print_time=6830.449 buffer_time=2.096 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 14 Hz
Stats 6806.7: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32794247 bytes_read=5047042 bytes_retransmit=9 bytes_invalid=0 send_seq=617607 receive_seq=617607 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015836 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42124 bytes_read=131721 bytes_retransmit=0 bytes_invalid=0 send_seq=6992 receive_seq=6992 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999425 adj=49997529 toolboard_t0: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=212774 bytes_read=6918173 bytes_retransmit=9 bytes_invalid=0 send_seq=29736 receive_seq=29736 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997747 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=137887 bytes_read=3752902 bytes_retransmit=9 bytes_invalid=0 send_seq=19136 receive_seq=19136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997590 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42391 bytes_read=1738081 bytes_retransmit=9 bytes_invalid=0 send_seq=7006 receive_seq=7006 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997712 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42877 bytes_read=129148 bytes_retransmit=9 bytes_invalid=0 send_seq=6993 receive_seq=6993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96969 bytes_read=2649060 bytes_retransmit=0 bytes_invalid=0 send_seq=11552 receive_seq=11552 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998699 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.2 th2: temp=61.8 th3: temp=59.2 sysload=0.16 cputime=526.949 memavail=7394776 print_time=6831.395 buffer_time=2.042 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 15 Hz
Stats 6807.7: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32797349 bytes_read=5047716 bytes_retransmit=9 bytes_invalid=0 send_seq=617674 receive_seq=617674 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=0 freq=400015824 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42130 bytes_read=131737 bytes_retransmit=0 bytes_invalid=0 send_seq=6993 receive_seq=6993 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999424 adj=49997554 toolboard_t0: mcu_awake=0.035 mcu_task_avg=0.000079 mcu_task_stddev=0.000074 bytes_write=212780 bytes_read=6918289 bytes_retransmit=9 bytes_invalid=0 send_seq=29737 receive_seq=29737 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997771 toolboard_t1: mcu_awake=0.264 mcu_task_avg=0.000116 mcu_task_stddev=0.000069 bytes_write=137963 bytes_read=3755976 bytes_retransmit=9 bytes_invalid=0 send_seq=19147 receive_seq=19147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997597 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42397 bytes_read=1738315 bytes_retransmit=9 bytes_invalid=0 send_seq=7007 receive_seq=7007 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997730 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42883 bytes_read=129164 bytes_retransmit=9 bytes_invalid=0 send_seq=6994 receive_seq=6994 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96975 bytes_read=2649405 bytes_retransmit=0 bytes_invalid=0 send_seq=11553 receive_seq=11553 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998693 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.1 th2: temp=61.7 th3: temp=59.3 sysload=0.16 cputime=527.031 memavail=7393812 print_time=6832.605 buffer_time=2.250 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 16 Hz
Stats 6808.7: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32800065 bytes_read=5048346 bytes_retransmit=9 bytes_invalid=0 send_seq=617735 receive_seq=617735 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=0 freq=400015854 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42136 bytes_read=131753 bytes_retransmit=0 bytes_invalid=0 send_seq=6994 receive_seq=6994 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999423 adj=49997536 toolboard_t0: mcu_awake=0.035 mcu_task_avg=0.000079 mcu_task_stddev=0.000074 bytes_write=212786 bytes_read=6918417 bytes_retransmit=9 bytes_invalid=0 send_seq=29738 receive_seq=29738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997757 toolboard_t1: mcu_awake=0.264 mcu_task_avg=0.000116 mcu_task_stddev=0.000069 bytes_write=138039 bytes_read=3759061 bytes_retransmit=9 bytes_invalid=0 send_seq=19158 receive_seq=19158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997592 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42403 bytes_read=1738549 bytes_retransmit=9 bytes_invalid=0 send_seq=7008 receive_seq=7008 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997719 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42889 bytes_read=129180 bytes_retransmit=9 bytes_invalid=0 send_seq=6995 receive_seq=6995 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96981 bytes_read=2649750 bytes_retransmit=0 bytes_invalid=0 send_seq=11554 receive_seq=11554 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998694 coil_temp=16.9 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=56.5 th1: temp=56.2 th2: temp=61.9 th3: temp=59.1 sysload=0.16 cputime=527.108 memavail=7393812 print_time=6833.518 buffer_time=2.163 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 17 Hz
Stats 6809.7: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32802443 bytes_read=5048931 bytes_retransmit=9 bytes_invalid=0 send_seq=617790 receive_seq=617790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015849 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42142 bytes_read=131769 bytes_retransmit=0 bytes_invalid=0 send_seq=6995 receive_seq=6995 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999423 adj=49997464 toolboard_t0: mcu_awake=0.035 mcu_task_avg=0.000079 mcu_task_stddev=0.000074 bytes_write=212792 bytes_read=6918517 bytes_retransmit=9 bytes_invalid=0 send_seq=29739 receive_seq=29739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997673 toolboard_t1: mcu_awake=0.264 mcu_task_avg=0.000116 mcu_task_stddev=0.000069 bytes_write=138108 bytes_read=3762157 bytes_retransmit=9 bytes_invalid=0 send_seq=19168 receive_seq=19168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997516 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42409 bytes_read=1738858 bytes_retransmit=9 bytes_invalid=0 send_seq=7009 receive_seq=7009 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42895 bytes_read=129196 bytes_retransmit=9 bytes_invalid=0 send_seq=6996 receive_seq=6996 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96987 bytes_read=2650095 bytes_retransmit=0 bytes_invalid=0 send_seq=11555 receive_seq=11555 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998649 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.5 th1: temp=56.1 th2: temp=61.8 th3: temp=59.3 sysload=0.16 cputime=527.186 memavail=7393812 print_time=6834.441 buffer_time=2.085 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 18 Hz
Stats 6810.7: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32805452 bytes_read=5049585 bytes_retransmit=9 bytes_invalid=0 send_seq=617856 receive_seq=617856 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015863 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=42148 bytes_read=131798 bytes_retransmit=0 bytes_invalid=0 send_seq=6996 receive_seq=6996 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999422 adj=49997465 toolboard_t0: mcu_awake=0.035 mcu_task_avg=0.000079 mcu_task_stddev=0.000074 bytes_write=212798 bytes_read=6918617 bytes_retransmit=9 bytes_invalid=0 send_seq=29740 receive_seq=29740 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997673 toolboard_t1: mcu_awake=0.264 mcu_task_avg=0.000116 mcu_task_stddev=0.000069 bytes_write=138184 bytes_read=3765214 bytes_retransmit=9 bytes_invalid=0 send_seq=19179 receive_seq=19179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997515 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42415 bytes_read=1739092 bytes_retransmit=9 bytes_invalid=0 send_seq=7010 receive_seq=7010 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42901 bytes_read=129212 bytes_retransmit=9 bytes_invalid=0 send_seq=6997 receive_seq=6997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96993 bytes_read=2650444 bytes_retransmit=0 bytes_invalid=0 send_seq=11556 receive_seq=11556 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998649 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.2 th2: temp=61.9 th3: temp=59.4 sysload=0.14 cputime=527.266 memavail=7393812 print_time=6835.358 buffer_time=2.002 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 19 Hz
Stats 6811.7: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32809049 bytes_read=5050290 bytes_retransmit=9 bytes_invalid=0 send_seq=617932 receive_seq=617932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=0 freq=400015849 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=42154 bytes_read=131814 bytes_retransmit=0 bytes_invalid=0 send_seq=6997 receive_seq=6997 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999421 adj=49997430 toolboard_t0: mcu_awake=0.035 mcu_task_avg=0.000079 mcu_task_stddev=0.000074 bytes_write=212804 bytes_read=6918745 bytes_retransmit=9 bytes_invalid=0 send_seq=29741 receive_seq=29741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997629 toolboard_t1: mcu_awake=0.264 mcu_task_avg=0.000116 mcu_task_stddev=0.000069 bytes_write=138260 bytes_read=3768301 bytes_retransmit=9 bytes_invalid=0 send_seq=19190 receive_seq=19190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997502 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42421 bytes_read=1739326 bytes_retransmit=9 bytes_invalid=0 send_seq=7011 receive_seq=7011 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42907 bytes_read=129239 bytes_retransmit=9 bytes_invalid=0 send_seq=6998 receive_seq=6998 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=96999 bytes_read=2650800 bytes_retransmit=0 bytes_invalid=0 send_seq=11557 receive_seq=11557 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998628 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.0 th2: temp=62.1 th3: temp=59.4 sysload=0.14 cputime=527.351 memavail=7393824 print_time=6836.578 buffer_time=2.221 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 20 Hz
Stats 6812.7: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32811665 bytes_read=5050910 bytes_retransmit=9 bytes_invalid=0 send_seq=617991 receive_seq=617991 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015829 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=42160 bytes_read=131830 bytes_retransmit=0 bytes_invalid=0 send_seq=6998 receive_seq=6998 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999420 adj=49997435 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212810 bytes_read=6918859 bytes_retransmit=9 bytes_invalid=0 send_seq=29742 receive_seq=29742 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997659 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138336 bytes_read=3771376 bytes_retransmit=9 bytes_invalid=0 send_seq=19201 receive_seq=19201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42427 bytes_read=1739620 bytes_retransmit=9 bytes_invalid=0 send_seq=7012 receive_seq=7012 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42913 bytes_read=129255 bytes_retransmit=9 bytes_invalid=0 send_seq=6999 receive_seq=6999 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97005 bytes_read=2651156 bytes_retransmit=0 bytes_invalid=0 send_seq=11558 receive_seq=11558 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998645 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.3 th2: temp=62.1 th3: temp=59.6 sysload=0.14 cputime=527.431 memavail=7393824 print_time=6837.503 buffer_time=2.145 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 21 Hz
Stats 6813.7: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32814822 bytes_read=5051589 bytes_retransmit=9 bytes_invalid=0 send_seq=618059 receive_seq=618059 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015841 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=42166 bytes_read=131846 bytes_retransmit=0 bytes_invalid=0 send_seq=6999 receive_seq=6999 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999418 adj=49997454 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212816 bytes_read=6918959 bytes_retransmit=9 bytes_invalid=0 send_seq=29743 receive_seq=29743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997690 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138412 bytes_read=3774433 bytes_retransmit=9 bytes_invalid=0 send_seq=19212 receive_seq=19212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42433 bytes_read=1739854 bytes_retransmit=9 bytes_invalid=0 send_seq=7013 receive_seq=7013 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997762 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42919 bytes_read=129271 bytes_retransmit=9 bytes_invalid=0 send_seq=7000 receive_seq=7000 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97011 bytes_read=2651512 bytes_retransmit=0 bytes_invalid=0 send_seq=11559 receive_seq=11559 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998659 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.2 th2: temp=62.3 th3: temp=59.6 sysload=0.14 cputime=527.511 memavail=7393824 print_time=6838.366 buffer_time=2.007 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 22 Hz
Stats 6814.7: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32818723 bytes_read=5052304 bytes_retransmit=9 bytes_invalid=0 send_seq=618140 receive_seq=618140 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=0 freq=400015842 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=42172 bytes_read=131862 bytes_retransmit=0 bytes_invalid=0 send_seq=7000 receive_seq=7000 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999417 adj=49997417 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212822 bytes_read=6919087 bytes_retransmit=9 bytes_invalid=0 send_seq=29744 receive_seq=29744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997742 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138488 bytes_read=3777519 bytes_retransmit=9 bytes_invalid=0 send_seq=19223 receive_seq=19223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997519 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42439 bytes_read=1740103 bytes_retransmit=9 bytes_invalid=0 send_seq=7014 receive_seq=7014 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997742 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42925 bytes_read=129287 bytes_retransmit=9 bytes_invalid=0 send_seq=7001 receive_seq=7001 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97017 bytes_read=2651868 bytes_retransmit=0 bytes_invalid=0 send_seq=11560 receive_seq=11560 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998646 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.2 th2: temp=62.3 th3: temp=59.7 sysload=0.14 cputime=527.599 memavail=7393824 print_time=6839.589 buffer_time=2.230 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 23 Hz
Stats 6815.7: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32821625 bytes_read=5052934 bytes_retransmit=9 bytes_invalid=0 send_seq=618204 receive_seq=618204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015828 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42178 bytes_read=131891 bytes_retransmit=0 bytes_invalid=0 send_seq=7001 receive_seq=7001 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999416 adj=49997403 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212828 bytes_read=6919187 bytes_retransmit=9 bytes_invalid=0 send_seq=29745 receive_seq=29745 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997702 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138564 bytes_read=3780576 bytes_retransmit=9 bytes_invalid=0 send_seq=19234 receive_seq=19234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997507 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42445 bytes_read=1740397 bytes_retransmit=9 bytes_invalid=0 send_seq=7015 receive_seq=7015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997704 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42931 bytes_read=129303 bytes_retransmit=9 bytes_invalid=0 send_seq=7002 receive_seq=7002 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97023 bytes_read=2652224 bytes_retransmit=0 bytes_invalid=0 send_seq=11561 receive_seq=11561 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998643 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.0 th2: temp=62.2 th3: temp=59.6 sysload=0.13 cputime=527.682 memavail=7393824 print_time=6840.531 buffer_time=2.171 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 24 Hz
Stats 6816.7: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32825000 bytes_read=5053631 bytes_retransmit=9 bytes_invalid=0 send_seq=618276 receive_seq=618276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015815 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42184 bytes_read=131907 bytes_retransmit=0 bytes_invalid=0 send_seq=7002 receive_seq=7002 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999416 adj=49997418 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212834 bytes_read=6919287 bytes_retransmit=9 bytes_invalid=0 send_seq=29746 receive_seq=29746 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997716 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138640 bytes_read=3783693 bytes_retransmit=9 bytes_invalid=0 send_seq=19245 receive_seq=19245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997535 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42451 bytes_read=1740631 bytes_retransmit=9 bytes_invalid=0 send_seq=7016 receive_seq=7016 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997708 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42937 bytes_read=129330 bytes_retransmit=9 bytes_invalid=0 send_seq=7003 receive_seq=7003 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97029 bytes_read=2652580 bytes_retransmit=0 bytes_invalid=0 send_seq=11562 receive_seq=11562 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998653 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.2 th2: temp=62.3 th3: temp=59.7 sysload=0.13 cputime=527.764 memavail=7393824 print_time=6841.391 buffer_time=2.031 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 25 Hz
Stats 6817.7: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32829166 bytes_read=5054380 bytes_retransmit=9 bytes_invalid=0 send_seq=618361 receive_seq=618361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=0 freq=400015816 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42190 bytes_read=131923 bytes_retransmit=0 bytes_invalid=0 send_seq=7003 receive_seq=7003 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999415 adj=49997437 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212840 bytes_read=6919429 bytes_retransmit=9 bytes_invalid=0 send_seq=29747 receive_seq=29747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997720 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138716 bytes_read=3786796 bytes_retransmit=9 bytes_invalid=0 send_seq=19256 receive_seq=19256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42457 bytes_read=1740865 bytes_retransmit=9 bytes_invalid=0 send_seq=7017 receive_seq=7017 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997762 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42943 bytes_read=129346 bytes_retransmit=9 bytes_invalid=0 send_seq=7004 receive_seq=7004 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97035 bytes_read=2652936 bytes_retransmit=0 bytes_invalid=0 send_seq=11563 receive_seq=11563 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998701 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.2 th2: temp=62.3 th3: temp=59.9 sysload=0.13 cputime=527.857 memavail=7392816 print_time=6842.607 buffer_time=2.245 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 26 Hz
Stats 6818.7: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32832281 bytes_read=5055030 bytes_retransmit=9 bytes_invalid=0 send_seq=618429 receive_seq=618429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=0 freq=400015802 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42196 bytes_read=131939 bytes_retransmit=0 bytes_invalid=0 send_seq=7004 receive_seq=7004 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999415 adj=49997433 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212846 bytes_read=6919529 bytes_retransmit=9 bytes_invalid=0 send_seq=29748 receive_seq=29748 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997701 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138792 bytes_read=3789853 bytes_retransmit=9 bytes_invalid=0 send_seq=19267 receive_seq=19267 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997535 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42463 bytes_read=1741159 bytes_retransmit=9 bytes_invalid=0 send_seq=7018 receive_seq=7018 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997719 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42949 bytes_read=129362 bytes_retransmit=9 bytes_invalid=0 send_seq=7005 receive_seq=7005 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97041 bytes_read=2653292 bytes_retransmit=0 bytes_invalid=0 send_seq=11564 receive_seq=11564 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998681 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.3 th2: temp=62.4 th3: temp=59.8 sysload=0.13 cputime=527.941 memavail=7392816 print_time=6843.553 buffer_time=2.190 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 27 Hz
Stats 6819.7: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32835862 bytes_read=5055739 bytes_retransmit=9 bytes_invalid=0 send_seq=618503 receive_seq=618503 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015794 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42202 bytes_read=131955 bytes_retransmit=0 bytes_invalid=0 send_seq=7005 receive_seq=7005 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999414 adj=49997452 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212852 bytes_read=6919629 bytes_retransmit=9 bytes_invalid=0 send_seq=29749 receive_seq=29749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997717 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138868 bytes_read=3792911 bytes_retransmit=9 bytes_invalid=0 send_seq=19278 receive_seq=19278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42469 bytes_read=1741408 bytes_retransmit=9 bytes_invalid=0 send_seq=7019 receive_seq=7019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997726 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42955 bytes_read=129378 bytes_retransmit=9 bytes_invalid=0 send_seq=7006 receive_seq=7006 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97047 bytes_read=2653648 bytes_retransmit=0 bytes_invalid=0 send_seq=11565 receive_seq=11565 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998685 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.0 th2: temp=62.5 th3: temp=59.9 sysload=0.13 cputime=528.025 memavail=7392816 print_time=6844.448 buffer_time=2.085 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 28 Hz
Stats 6820.7: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32839481 bytes_read=5056429 bytes_retransmit=9 bytes_invalid=0 send_seq=618579 receive_seq=618579 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015781 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42208 bytes_read=131984 bytes_retransmit=0 bytes_invalid=0 send_seq=7006 receive_seq=7006 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999413 adj=49997455 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212858 bytes_read=6919757 bytes_retransmit=9 bytes_invalid=0 send_seq=29750 receive_seq=29750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997716 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=138944 bytes_read=3795996 bytes_retransmit=9 bytes_invalid=0 send_seq=19289 receive_seq=19289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997561 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42475 bytes_read=1741642 bytes_retransmit=9 bytes_invalid=0 send_seq=7020 receive_seq=7020 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997726 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42961 bytes_read=129394 bytes_retransmit=9 bytes_invalid=0 send_seq=7007 receive_seq=7007 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97053 bytes_read=2654004 bytes_retransmit=0 bytes_invalid=0 send_seq=11566 receive_seq=11566 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998686 coil_temp=16.9 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.1 th2: temp=62.4 th3: temp=59.9 sysload=0.12 cputime=528.110 memavail=7392816 print_time=6845.411 buffer_time=2.047 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 29 Hz
Stats 6821.7: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32843946 bytes_read=5057205 bytes_retransmit=9 bytes_invalid=0 send_seq=618670 receive_seq=618670 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015766 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42220 bytes_read=132016 bytes_retransmit=0 bytes_invalid=0 send_seq=7008 receive_seq=7008 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999414 adj=49997456 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212870 bytes_read=6919867 bytes_retransmit=9 bytes_invalid=0 send_seq=29752 receive_seq=29752 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997721 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139026 bytes_read=3799059 bytes_retransmit=9 bytes_invalid=0 send_seq=19301 receive_seq=19301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997573 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42487 bytes_read=1741952 bytes_retransmit=9 bytes_invalid=0 send_seq=7022 receive_seq=7022 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997726 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42973 bytes_read=129437 bytes_retransmit=9 bytes_invalid=0 send_seq=7009 receive_seq=7009 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.7 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97065 bytes_read=2654376 bytes_retransmit=0 bytes_invalid=0 send_seq=11568 receive_seq=11568 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998688 coil_temp=16.9 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.2 th2: temp=62.5 th3: temp=59.7 sysload=0.12 cputime=528.205 memavail=7392868 print_time=6846.614 buffer_time=2.247 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 30 Hz
Stats 6822.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32847199 bytes_read=5057910 bytes_retransmit=9 bytes_invalid=0 send_seq=618740 receive_seq=618740 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015771 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42226 bytes_read=132032 bytes_retransmit=0 bytes_invalid=0 send_seq=7009 receive_seq=7009 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999413 adj=49997483 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212876 bytes_read=6919974 bytes_retransmit=9 bytes_invalid=0 send_seq=29753 receive_seq=29753 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997805 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139102 bytes_read=3802174 bytes_retransmit=9 bytes_invalid=0 send_seq=19312 receive_seq=19312 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997588 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42493 bytes_read=1742186 bytes_retransmit=9 bytes_invalid=0 send_seq=7023 receive_seq=7023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997714 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42979 bytes_read=129453 bytes_retransmit=9 bytes_invalid=0 send_seq=7010 receive_seq=7010 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97071 bytes_read=2654732 bytes_retransmit=0 bytes_invalid=0 send_seq=11569 receive_seq=11569 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998715 coil_temp=16.9 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.2 th2: temp=62.6 th3: temp=60.0 sysload=0.12 cputime=528.289 memavail=7392868 print_time=6847.468 buffer_time=2.099 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 31 Hz
Stats 6823.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32851233 bytes_read=5058635 bytes_retransmit=9 bytes_invalid=0 send_seq=618823 receive_seq=618823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015771 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42232 bytes_read=132048 bytes_retransmit=0 bytes_invalid=0 send_seq=7010 receive_seq=7010 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999413 adj=49997467 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212882 bytes_read=6920093 bytes_retransmit=9 bytes_invalid=0 send_seq=29754 receive_seq=29754 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997768 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139178 bytes_read=3805240 bytes_retransmit=9 bytes_invalid=0 send_seq=19323 receive_seq=19323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997627 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42499 bytes_read=1742435 bytes_retransmit=9 bytes_invalid=0 send_seq=7024 receive_seq=7024 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997696 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42985 bytes_read=129469 bytes_retransmit=9 bytes_invalid=0 send_seq=7011 receive_seq=7011 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97077 bytes_read=2655088 bytes_retransmit=0 bytes_invalid=0 send_seq=11570 receive_seq=11570 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998707 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.2 th2: temp=62.6 th3: temp=60.0 sysload=0.12 cputime=528.386 memavail=7393640 print_time=6848.450 buffer_time=2.080 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 32 Hz
Stats 6824.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32855756 bytes_read=5059400 bytes_retransmit=9 bytes_invalid=0 send_seq=618914 receive_seq=618914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=0 freq=400015763 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42238 bytes_read=132064 bytes_retransmit=0 bytes_invalid=0 send_seq=7011 receive_seq=7011 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999413 adj=49997461 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212888 bytes_read=6920186 bytes_retransmit=9 bytes_invalid=0 send_seq=29755 receive_seq=29755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997742 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139254 bytes_read=3808281 bytes_retransmit=9 bytes_invalid=0 send_seq=19334 receive_seq=19334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997611 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42505 bytes_read=1742729 bytes_retransmit=9 bytes_invalid=0 send_seq=7025 receive_seq=7025 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42991 bytes_read=129485 bytes_retransmit=9 bytes_invalid=0 send_seq=7012 receive_seq=7012 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97083 bytes_read=2655444 bytes_retransmit=0 bytes_invalid=0 send_seq=11571 receive_seq=11571 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998694 coil_temp=16.9 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.3 th2: temp=62.7 th3: temp=60.0 sysload=0.12 cputime=528.478 memavail=7393736 print_time=6849.633 buffer_time=2.260 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 33 Hz
Stats 6825.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32859125 bytes_read=5060094 bytes_retransmit=9 bytes_invalid=0 send_seq=618985 receive_seq=618985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015756 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42244 bytes_read=132093 bytes_retransmit=0 bytes_invalid=0 send_seq=7012 receive_seq=7012 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999412 adj=49997463 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212894 bytes_read=6920284 bytes_retransmit=9 bytes_invalid=0 send_seq=29756 receive_seq=29756 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997731 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139330 bytes_read=3811331 bytes_retransmit=9 bytes_invalid=0 send_seq=19345 receive_seq=19345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997595 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42511 bytes_read=1742963 bytes_retransmit=9 bytes_invalid=0 send_seq=7026 receive_seq=7026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=42997 bytes_read=129501 bytes_retransmit=9 bytes_invalid=0 send_seq=7013 receive_seq=7013 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97089 bytes_read=2655800 bytes_retransmit=0 bytes_invalid=0 send_seq=11572 receive_seq=11572 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998691 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.1 th2: temp=62.8 th3: temp=60.0 sysload=0.11 cputime=528.564 memavail=7393736 print_time=6850.507 buffer_time=2.132 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 34 Hz
Stats 6826.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32863380 bytes_read=5060834 bytes_retransmit=9 bytes_invalid=0 send_seq=619071 receive_seq=619071 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015749 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42250 bytes_read=132109 bytes_retransmit=0 bytes_invalid=0 send_seq=7013 receive_seq=7013 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999410 adj=49997456 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212900 bytes_read=6920412 bytes_retransmit=9 bytes_invalid=0 send_seq=29757 receive_seq=29757 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997726 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139406 bytes_read=3814417 bytes_retransmit=9 bytes_invalid=0 send_seq=19356 receive_seq=19356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997592 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42517 bytes_read=1743212 bytes_retransmit=9 bytes_invalid=0 send_seq=7027 receive_seq=7027 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43003 bytes_read=129528 bytes_retransmit=9 bytes_invalid=0 send_seq=7014 receive_seq=7014 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97095 bytes_read=2656156 bytes_retransmit=0 bytes_invalid=0 send_seq=11573 receive_seq=11573 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998694 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.2 th2: temp=62.7 th3: temp=60.2 sysload=0.11 cputime=528.651 memavail=7393736 print_time=6851.468 buffer_time=2.092 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 35 Hz
Stats 6827.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32868295 bytes_read=5061638 bytes_retransmit=9 bytes_invalid=0 send_seq=619167 receive_seq=619167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=24 freq=400015741 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42256 bytes_read=132125 bytes_retransmit=0 bytes_invalid=0 send_seq=7014 receive_seq=7014 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999411 adj=49997450 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=212906 bytes_read=6920526 bytes_retransmit=9 bytes_invalid=0 send_seq=29758 receive_seq=29758 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997722 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139482 bytes_read=3817548 bytes_retransmit=9 bytes_invalid=0 send_seq=19367 receive_seq=19367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997590 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42523 bytes_read=1743491 bytes_retransmit=9 bytes_invalid=0 send_seq=7028 receive_seq=7028 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997723 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43009 bytes_read=129544 bytes_retransmit=9 bytes_invalid=0 send_seq=7015 receive_seq=7015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999463 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97101 bytes_read=2656512 bytes_retransmit=0 bytes_invalid=0 send_seq=11574 receive_seq=11574 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998799 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.2 th2: temp=62.7 th3: temp=60.1 sysload=0.11 cputime=528.746 memavail=7394552 print_time=6852.670 buffer_time=2.291 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 36 Hz
Stats 6828.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32871716 bytes_read=5062335 bytes_retransmit=9 bytes_invalid=0 send_seq=619239 receive_seq=619239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=0 freq=400015733 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42262 bytes_read=132141 bytes_retransmit=0 bytes_invalid=0 send_seq=7015 receive_seq=7015 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999410 adj=49997461 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=212912 bytes_read=6920626 bytes_retransmit=9 bytes_invalid=0 send_seq=29759 receive_seq=29759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997731 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139551 bytes_read=3820582 bytes_retransmit=9 bytes_invalid=0 send_seq=19377 receive_seq=19377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997581 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42529 bytes_read=1743725 bytes_retransmit=9 bytes_invalid=0 send_seq=7029 receive_seq=7029 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997710 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43015 bytes_read=129560 bytes_retransmit=9 bytes_invalid=0 send_seq=7016 receive_seq=7016 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97107 bytes_read=2656868 bytes_retransmit=0 bytes_invalid=0 send_seq=11575 receive_seq=11575 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998763 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.1 th2: temp=62.7 th3: temp=60.1 sysload=0.11 cputime=528.832 memavail=7394552 print_time=6853.560 buffer_time=2.179 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 37 Hz
Stats 6829.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32876305 bytes_read=5063095 bytes_retransmit=9 bytes_invalid=0 send_seq=619329 receive_seq=619329 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015726 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42268 bytes_read=132157 bytes_retransmit=0 bytes_invalid=0 send_seq=7016 receive_seq=7016 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999410 adj=49997469 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=212918 bytes_read=6920754 bytes_retransmit=9 bytes_invalid=0 send_seq=29760 receive_seq=29760 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997749 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139627 bytes_read=3823667 bytes_retransmit=9 bytes_invalid=0 send_seq=19388 receive_seq=19388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997589 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42535 bytes_read=1744004 bytes_retransmit=9 bytes_invalid=0 send_seq=7030 receive_seq=7030 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997721 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43021 bytes_read=129576 bytes_retransmit=9 bytes_invalid=0 send_seq=7017 receive_seq=7017 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999474 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97113 bytes_read=2657224 bytes_retransmit=0 bytes_invalid=0 send_seq=11576 receive_seq=11576 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998758 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.1 th2: temp=62.7 th3: temp=60.1 sysload=0.11 cputime=528.921 memavail=7394328 print_time=6854.496 buffer_time=2.112 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 38 Hz
Stats 6830.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32880831 bytes_read=5063855 bytes_retransmit=9 bytes_invalid=0 send_seq=619419 receive_seq=619419 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=611 freq=400015720 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42274 bytes_read=132186 bytes_retransmit=0 bytes_invalid=0 send_seq=7017 receive_seq=7017 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999410 adj=49997476 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=212924 bytes_read=6920854 bytes_retransmit=9 bytes_invalid=0 send_seq=29761 receive_seq=29761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997741 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139703 bytes_read=3826724 bytes_retransmit=9 bytes_invalid=0 send_seq=19399 receive_seq=19399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997605 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42541 bytes_read=1744268 bytes_retransmit=9 bytes_invalid=0 send_seq=7031 receive_seq=7031 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997719 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43027 bytes_read=129592 bytes_retransmit=9 bytes_invalid=0 send_seq=7018 receive_seq=7018 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999470 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97119 bytes_read=2657580 bytes_retransmit=0 bytes_invalid=0 send_seq=11577 receive_seq=11577 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998750 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.2 th2: temp=62.9 th3: temp=60.2 sysload=0.10 cputime=529.019 memavail=7394328 print_time=6855.694 buffer_time=2.305 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 39 Hz
Stats 6831.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32885041 bytes_read=5064604 bytes_retransmit=9 bytes_invalid=0 send_seq=619501 receive_seq=619501 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015724 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42280 bytes_read=132202 bytes_retransmit=0 bytes_invalid=0 send_seq=7018 receive_seq=7018 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999410 adj=49997475 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=212930 bytes_read=6920954 bytes_retransmit=9 bytes_invalid=0 send_seq=29762 receive_seq=29762 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997729 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139779 bytes_read=3829839 bytes_retransmit=9 bytes_invalid=0 send_seq=19410 receive_seq=19410 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997592 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42547 bytes_read=1744502 bytes_retransmit=9 bytes_invalid=0 send_seq=7032 receive_seq=7032 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997709 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43033 bytes_read=129619 bytes_retransmit=9 bytes_invalid=0 send_seq=7019 receive_seq=7019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999477 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97125 bytes_read=2657936 bytes_retransmit=0 bytes_invalid=0 send_seq=11578 receive_seq=11578 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998730 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.2 th2: temp=62.8 th3: temp=60.2 sysload=0.10 cputime=529.112 memavail=7394328 print_time=6856.586 buffer_time=2.196 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 40 Hz
Stats 6832.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32889406 bytes_read=5065350 bytes_retransmit=9 bytes_invalid=0 send_seq=619585 receive_seq=619585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=246 freq=400015723 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42286 bytes_read=132218 bytes_retransmit=0 bytes_invalid=0 send_seq=7019 receive_seq=7019 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999409 adj=49997457 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212936 bytes_read=6921096 bytes_retransmit=9 bytes_invalid=0 send_seq=29763 receive_seq=29763 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997768 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139855 bytes_read=3832940 bytes_retransmit=9 bytes_invalid=0 send_seq=19421 receive_seq=19421 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997577 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42553 bytes_read=1744781 bytes_retransmit=9 bytes_invalid=0 send_seq=7033 receive_seq=7033 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997692 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43039 bytes_read=129635 bytes_retransmit=9 bytes_invalid=0 send_seq=7020 receive_seq=7020 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999480 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97131 bytes_read=2658292 bytes_retransmit=0 bytes_invalid=0 send_seq=11579 receive_seq=11579 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998710 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.2 th2: temp=62.7 th3: temp=60.2 sysload=0.10 cputime=529.204 memavail=7394328 print_time=6857.502 buffer_time=2.110 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 41 Hz
Stats 6833.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32893459 bytes_read=5066060 bytes_retransmit=9 bytes_invalid=0 send_seq=619665 receive_seq=619665 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015736 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42292 bytes_read=132234 bytes_retransmit=0 bytes_invalid=0 send_seq=7020 receive_seq=7020 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999409 adj=49997447 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212942 bytes_read=6921196 bytes_retransmit=9 bytes_invalid=0 send_seq=29764 receive_seq=29764 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997747 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=139931 bytes_read=3835997 bytes_retransmit=9 bytes_invalid=0 send_seq=19432 receive_seq=19432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997570 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42559 bytes_read=1745030 bytes_retransmit=9 bytes_invalid=0 send_seq=7034 receive_seq=7034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43045 bytes_read=129651 bytes_retransmit=9 bytes_invalid=0 send_seq=7021 receive_seq=7021 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999473 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97137 bytes_read=2658648 bytes_retransmit=0 bytes_invalid=0 send_seq=11580 receive_seq=11580 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998730 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=56.8 th1: temp=55.9 th2: temp=62.7 th3: temp=60.4 sysload=0.10 cputime=529.298 memavail=7394368 print_time=6858.397 buffer_time=2.004 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 42 Hz
Stats 6834.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32898839 bytes_read=5066914 bytes_retransmit=9 bytes_invalid=0 send_seq=619768 receive_seq=619768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=22 upcoming_bytes=196 freq=400015755 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42298 bytes_read=132250 bytes_retransmit=0 bytes_invalid=0 send_seq=7021 receive_seq=7021 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999409 adj=49997424 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212948 bytes_read=6921296 bytes_retransmit=9 bytes_invalid=0 send_seq=29765 receive_seq=29765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997698 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140007 bytes_read=3839053 bytes_retransmit=9 bytes_invalid=0 send_seq=19443 receive_seq=19443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42565 bytes_read=1745279 bytes_retransmit=9 bytes_invalid=0 send_seq=7035 receive_seq=7035 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997657 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43051 bytes_read=129667 bytes_retransmit=9 bytes_invalid=0 send_seq=7022 receive_seq=7022 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97143 bytes_read=2659004 bytes_retransmit=0 bytes_invalid=0 send_seq=11581 receive_seq=11581 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998713 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.2 th2: temp=62.8 th3: temp=60.3 sysload=0.10 cputime=529.400 memavail=7394368 print_time=6859.608 buffer_time=2.212 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 43 Hz
Stats 6835.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32902969 bytes_read=5067629 bytes_retransmit=9 bytes_invalid=0 send_seq=619849 receive_seq=619849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=845 freq=400015769 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42304 bytes_read=132279 bytes_retransmit=0 bytes_invalid=0 send_seq=7022 receive_seq=7022 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999410 adj=49997405 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212954 bytes_read=6921424 bytes_retransmit=9 bytes_invalid=0 send_seq=29766 receive_seq=29766 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997677 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140083 bytes_read=3842137 bytes_retransmit=9 bytes_invalid=0 send_seq=19454 receive_seq=19454 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997495 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42571 bytes_read=1745558 bytes_retransmit=9 bytes_invalid=0 send_seq=7036 receive_seq=7036 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43057 bytes_read=129683 bytes_retransmit=9 bytes_invalid=0 send_seq=7023 receive_seq=7023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97149 bytes_read=2659360 bytes_retransmit=0 bytes_invalid=0 send_seq=11582 receive_seq=11582 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998685 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.2 th2: temp=63.0 th3: temp=60.3 sysload=0.09 cputime=529.493 memavail=7394368 print_time=6860.529 buffer_time=2.131 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 44 Hz
Stats 6836.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32907698 bytes_read=5068399 bytes_retransmit=9 bytes_invalid=0 send_seq=619941 receive_seq=619941 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=0 freq=400015780 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42310 bytes_read=132295 bytes_retransmit=0 bytes_invalid=0 send_seq=7023 receive_seq=7023 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999409 adj=49997394 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212960 bytes_read=6921524 bytes_retransmit=9 bytes_invalid=0 send_seq=29767 receive_seq=29767 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997636 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140159 bytes_read=3845252 bytes_retransmit=9 bytes_invalid=0 send_seq=19465 receive_seq=19465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997465 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42577 bytes_read=1745807 bytes_retransmit=9 bytes_invalid=0 send_seq=7037 receive_seq=7037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997614 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43063 bytes_read=129710 bytes_retransmit=9 bytes_invalid=0 send_seq=7024 receive_seq=7024 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999439 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97155 bytes_read=2659734 bytes_retransmit=0 bytes_invalid=0 send_seq=11583 receive_seq=11583 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998656 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.1 th2: temp=62.9 th3: temp=60.3 sysload=0.09 cputime=529.592 memavail=7394368 print_time=6861.414 buffer_time=2.014 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 45 Hz
Stats 6837.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32912997 bytes_read=5069269 bytes_retransmit=9 bytes_invalid=0 send_seq=620044 receive_seq=620044 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=15 upcoming_bytes=474 freq=400015780 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42316 bytes_read=132311 bytes_retransmit=0 bytes_invalid=0 send_seq=7024 receive_seq=7024 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999409 adj=49997380 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212966 bytes_read=6921638 bytes_retransmit=9 bytes_invalid=0 send_seq=29768 receive_seq=29768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997688 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140235 bytes_read=3848326 bytes_retransmit=9 bytes_invalid=0 send_seq=19476 receive_seq=19476 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997447 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42583 bytes_read=1746041 bytes_retransmit=9 bytes_invalid=0 send_seq=7038 receive_seq=7038 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997601 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43069 bytes_read=129726 bytes_retransmit=9 bytes_invalid=0 send_seq=7025 receive_seq=7025 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97161 bytes_read=2660090 bytes_retransmit=0 bytes_invalid=0 send_seq=11584 receive_seq=11584 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998635 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.4 th2: temp=62.9 th3: temp=60.3 sysload=0.09 cputime=529.699 memavail=7392868 print_time=6862.611 buffer_time=2.208 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 46 Hz
Stats 6838.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32917214 bytes_read=5069979 bytes_retransmit=9 bytes_invalid=0 send_seq=620125 receive_seq=620125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=1192 freq=400015789 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42322 bytes_read=132327 bytes_retransmit=0 bytes_invalid=0 send_seq=7025 receive_seq=7025 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999408 adj=49997386 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212972 bytes_read=6921766 bytes_retransmit=9 bytes_invalid=0 send_seq=29769 receive_seq=29769 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997676 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140311 bytes_read=3851411 bytes_retransmit=9 bytes_invalid=0 send_seq=19487 receive_seq=19487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997466 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42589 bytes_read=1746335 bytes_retransmit=9 bytes_invalid=0 send_seq=7039 receive_seq=7039 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997612 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43075 bytes_read=129742 bytes_retransmit=9 bytes_invalid=0 send_seq=7026 receive_seq=7026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97167 bytes_read=2660446 bytes_retransmit=0 bytes_invalid=0 send_seq=11585 receive_seq=11585 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998639 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.0 th2: temp=62.8 th3: temp=60.4 sysload=0.09 cputime=529.797 memavail=7392868 print_time=6863.548 buffer_time=2.143 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 47 Hz
Stats 6839.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32922338 bytes_read=5070774 bytes_retransmit=9 bytes_invalid=0 send_seq=620222 receive_seq=620222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=0 freq=400015798 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42328 bytes_read=132343 bytes_retransmit=0 bytes_invalid=0 send_seq=7026 receive_seq=7026 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999409 adj=49997375 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212978 bytes_read=6921866 bytes_retransmit=9 bytes_invalid=0 send_seq=29770 receive_seq=29770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997755 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140387 bytes_read=3854469 bytes_retransmit=9 bytes_invalid=0 send_seq=19498 receive_seq=19498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997457 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42595 bytes_read=1746584 bytes_retransmit=9 bytes_invalid=0 send_seq=7040 receive_seq=7040 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997603 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43081 bytes_read=129758 bytes_retransmit=9 bytes_invalid=0 send_seq=7027 receive_seq=7027 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97173 bytes_read=2660802 bytes_retransmit=0 bytes_invalid=0 send_seq=11586 receive_seq=11586 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998630 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.2 th2: temp=63.0 th3: temp=60.3 sysload=0.09 cputime=529.898 memavail=7392876 print_time=6864.440 buffer_time=2.032 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 48 Hz
Stats 6840.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32927542 bytes_read=5071613 bytes_retransmit=9 bytes_invalid=0 send_seq=620322 receive_seq=620322 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=701 freq=400015819 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42334 bytes_read=132372 bytes_retransmit=0 bytes_invalid=0 send_seq=7027 receive_seq=7027 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999411 adj=49997374 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212984 bytes_read=6921966 bytes_retransmit=9 bytes_invalid=0 send_seq=29771 receive_seq=29771 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997728 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140463 bytes_read=3857584 bytes_retransmit=9 bytes_invalid=0 send_seq=19509 receive_seq=19509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997452 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42601 bytes_read=1746818 bytes_retransmit=9 bytes_invalid=0 send_seq=7041 receive_seq=7041 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43087 bytes_read=129774 bytes_retransmit=9 bytes_invalid=0 send_seq=7028 receive_seq=7028 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97179 bytes_read=2661158 bytes_retransmit=0 bytes_invalid=0 send_seq=11587 receive_seq=11587 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998625 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.3 th2: temp=63.0 th3: temp=60.3 sysload=0.17 cputime=530.016 memavail=7386580 print_time=6865.645 buffer_time=2.234 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 49 Hz
Stats 6841.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=32931758 bytes_read=5072333 bytes_retransmit=9 bytes_invalid=0 send_seq=620404 receive_seq=620404 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=1528 freq=400015820 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42340 bytes_read=132388 bytes_retransmit=0 bytes_invalid=0 send_seq=7028 receive_seq=7028 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999412 adj=49997394 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212990 bytes_read=6922094 bytes_retransmit=9 bytes_invalid=0 send_seq=29772 receive_seq=29772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997672 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140539 bytes_read=3860669 bytes_retransmit=9 bytes_invalid=0 send_seq=19520 receive_seq=19520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997442 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42607 bytes_read=1747112 bytes_retransmit=9 bytes_invalid=0 send_seq=7042 receive_seq=7042 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997602 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43093 bytes_read=129801 bytes_retransmit=9 bytes_invalid=0 send_seq=7029 receive_seq=7029 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97185 bytes_read=2661514 bytes_retransmit=0 bytes_invalid=0 send_seq=11588 receive_seq=11588 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998616 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.2 th2: temp=63.0 th3: temp=60.5 sysload=0.17 cputime=530.118 memavail=7393236 print_time=6866.559 buffer_time=2.146 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 50 Hz
Stats 6842.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=32937088 bytes_read=5073149 bytes_retransmit=9 bytes_invalid=0 send_seq=620502 receive_seq=620502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=15 upcoming_bytes=324 freq=400015819 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42346 bytes_read=132404 bytes_retransmit=0 bytes_invalid=0 send_seq=7029 receive_seq=7029 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999411 adj=49997400 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=212996 bytes_read=6922208 bytes_retransmit=9 bytes_invalid=0 send_seq=29773 receive_seq=29773 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997656 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140615 bytes_read=3863743 bytes_retransmit=9 bytes_invalid=0 send_seq=19531 receive_seq=19531 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997459 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42613 bytes_read=1747346 bytes_retransmit=9 bytes_invalid=0 send_seq=7043 receive_seq=7043 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997621 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43099 bytes_read=129817 bytes_retransmit=9 bytes_invalid=0 send_seq=7030 receive_seq=7030 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97191 bytes_read=2661870 bytes_retransmit=0 bytes_invalid=0 send_seq=11589 receive_seq=11589 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998612 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.2 th2: temp=63.0 th3: temp=60.5 sysload=0.17 cputime=530.219 memavail=7395752 print_time=6867.457 buffer_time=2.042 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 51 Hz
Stats 6843.7: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=32942465 bytes_read=5073993 bytes_retransmit=9 bytes_invalid=0 send_seq=620604 receive_seq=620603 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=884 freq=400015811 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42352 bytes_read=132420 bytes_retransmit=0 bytes_invalid=0 send_seq=7030 receive_seq=7030 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999411 adj=49997399 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213002 bytes_read=6922322 bytes_retransmit=9 bytes_invalid=0 send_seq=29774 receive_seq=29774 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997647 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140691 bytes_read=3866802 bytes_retransmit=9 bytes_invalid=0 send_seq=19542 receive_seq=19542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997477 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42619 bytes_read=1747580 bytes_retransmit=9 bytes_invalid=0 send_seq=7044 receive_seq=7044 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43105 bytes_read=129833 bytes_retransmit=9 bytes_invalid=0 send_seq=7031 receive_seq=7031 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97197 bytes_read=2662226 bytes_retransmit=0 bytes_invalid=0 send_seq=11590 receive_seq=11590 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998613 coil_temp=16.8 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.0 th2: temp=63.0 th3: temp=60.5 sysload=0.17 cputime=530.327 memavail=7395516 print_time=6868.645 buffer_time=2.226 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 52 Hz
Stats 6844.8: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=32946841 bytes_read=5074733 bytes_retransmit=9 bytes_invalid=0 send_seq=620689 receive_seq=620689 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=1780 freq=400015842 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42358 bytes_read=132436 bytes_retransmit=0 bytes_invalid=0 send_seq=7031 receive_seq=7031 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999412 adj=49997420 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213008 bytes_read=6922436 bytes_retransmit=9 bytes_invalid=0 send_seq=29775 receive_seq=29775 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997658 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140767 bytes_read=3869945 bytes_retransmit=9 bytes_invalid=0 send_seq=19553 receive_seq=19553 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997503 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42625 bytes_read=1747889 bytes_retransmit=9 bytes_invalid=0 send_seq=7045 receive_seq=7045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43111 bytes_read=129848 bytes_retransmit=9 bytes_invalid=0 send_seq=7032 receive_seq=7032 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97203 bytes_read=2662582 bytes_retransmit=0 bytes_invalid=0 send_seq=11591 receive_seq=11591 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998628 coil_temp=16.8 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.3 th2: temp=62.7 th3: temp=60.5 sysload=0.17 cputime=530.425 memavail=7395516 print_time=6869.574 buffer_time=2.152 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 53 Hz
Stats 6845.8: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=32952299 bytes_read=5075563 bytes_retransmit=9 bytes_invalid=0 send_seq=620793 receive_seq=620793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=15 upcoming_bytes=578 freq=400015843 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=42364 bytes_read=132465 bytes_retransmit=0 bytes_invalid=0 send_seq=7032 receive_seq=7032 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999411 adj=49997389 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213014 bytes_read=6922536 bytes_retransmit=9 bytes_invalid=0 send_seq=29776 receive_seq=29776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997618 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140843 bytes_read=3873001 bytes_retransmit=9 bytes_invalid=0 send_seq=19564 receive_seq=19564 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997448 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42631 bytes_read=1748123 bytes_retransmit=9 bytes_invalid=0 send_seq=7046 receive_seq=7046 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43117 bytes_read=129863 bytes_retransmit=9 bytes_invalid=0 send_seq=7033 receive_seq=7033 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97209 bytes_read=2662938 bytes_retransmit=0 bytes_invalid=0 send_seq=11592 receive_seq=11592 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998602 coil_temp=16.8 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.2 th2: temp=63.0 th3: temp=60.5 sysload=0.15 cputime=530.527 memavail=7395292 print_time=6870.468 buffer_time=2.045 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 54 Hz
Stats 6846.8: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=32957868 bytes_read=5076417 bytes_retransmit=9 bytes_invalid=0 send_seq=620896 receive_seq=620896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=1224 freq=400015865 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=42370 bytes_read=132481 bytes_retransmit=0 bytes_invalid=0 send_seq=7033 receive_seq=7033 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999411 adj=49997378 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213020 bytes_read=6922650 bytes_retransmit=9 bytes_invalid=0 send_seq=29777 receive_seq=29777 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997678 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140919 bytes_read=3876059 bytes_retransmit=9 bytes_invalid=0 send_seq=19575 receive_seq=19575 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997452 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42637 bytes_read=1748357 bytes_retransmit=9 bytes_invalid=0 send_seq=7047 receive_seq=7047 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43123 bytes_read=129889 bytes_retransmit=9 bytes_invalid=0 send_seq=7034 receive_seq=7034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97215 bytes_read=2663294 bytes_retransmit=0 bytes_invalid=0 send_seq=11593 receive_seq=11593 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998607 coil_temp=16.8 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.1 th2: temp=63.0 th3: temp=60.5 sysload=0.15 cputime=530.636 memavail=7395292 print_time=6871.673 buffer_time=2.247 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 55 Hz
Stats 6847.8: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32962359 bytes_read=5077183 bytes_retransmit=9 bytes_invalid=0 send_seq=620984 receive_seq=620984 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=36 upcoming_bytes=2022 freq=400015891 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=42376 bytes_read=132497 bytes_retransmit=0 bytes_invalid=0 send_seq=7034 receive_seq=7034 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999411 adj=49997357 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213026 bytes_read=6922778 bytes_retransmit=9 bytes_invalid=0 send_seq=29778 receive_seq=29778 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997624 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=140995 bytes_read=3879160 bytes_retransmit=9 bytes_invalid=0 send_seq=19586 receive_seq=19586 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997430 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42643 bytes_read=1748651 bytes_retransmit=9 bytes_invalid=0 send_seq=7048 receive_seq=7048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43129 bytes_read=129904 bytes_retransmit=9 bytes_invalid=0 send_seq=7035 receive_seq=7035 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97221 bytes_read=2663650 bytes_retransmit=0 bytes_invalid=0 send_seq=11594 receive_seq=11594 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998600 coil_temp=16.8 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.1 th2: temp=63.0 th3: temp=60.5 sysload=0.15 cputime=530.737 memavail=7393304 print_time=6872.583 buffer_time=2.154 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 56 Hz
Stats 6848.8: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32967956 bytes_read=5078018 bytes_retransmit=9 bytes_invalid=0 send_seq=621089 receive_seq=621089 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=840 freq=400015903 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=42382 bytes_read=132513 bytes_retransmit=0 bytes_invalid=0 send_seq=7035 receive_seq=7035 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999410 adj=49997327 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213032 bytes_read=6922878 bytes_retransmit=9 bytes_invalid=0 send_seq=29779 receive_seq=29779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997639 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141071 bytes_read=3882216 bytes_retransmit=9 bytes_invalid=0 send_seq=19597 receive_seq=19597 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997401 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42649 bytes_read=1748885 bytes_retransmit=9 bytes_invalid=0 send_seq=7049 receive_seq=7049 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997576 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43135 bytes_read=129919 bytes_retransmit=9 bytes_invalid=0 send_seq=7036 receive_seq=7036 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999419 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97227 bytes_read=2664006 bytes_retransmit=0 bytes_invalid=0 send_seq=11595 receive_seq=11595 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998581 coil_temp=16.8 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.1 th2: temp=63.0 th3: temp=60.5 sysload=0.15 cputime=530.840 memavail=7393304 print_time=6873.497 buffer_time=2.066 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 57 Hz
Stats 6849.8: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32973581 bytes_read=5078882 bytes_retransmit=9 bytes_invalid=0 send_seq=621195 receive_seq=621195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=1661 freq=400015895 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000010 bytes_write=42388 bytes_read=132529 bytes_retransmit=0 bytes_invalid=0 send_seq=7036 receive_seq=7036 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999410 adj=49997317 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213038 bytes_read=6923006 bytes_retransmit=9 bytes_invalid=0 send_seq=29780 receive_seq=29780 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997674 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141147 bytes_read=3885346 bytes_retransmit=9 bytes_invalid=0 send_seq=19608 receive_seq=19608 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997386 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42655 bytes_read=1749134 bytes_retransmit=9 bytes_invalid=0 send_seq=7050 receive_seq=7050 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997562 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43141 bytes_read=129934 bytes_retransmit=9 bytes_invalid=0 send_seq=7037 receive_seq=7037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999419 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97233 bytes_read=2664362 bytes_retransmit=0 bytes_invalid=0 send_seq=11596 receive_seq=11596 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998598 coil_temp=16.8 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=57.2 th1: temp=56.3 th2: temp=63.0 th3: temp=60.5 sysload=0.15 cputime=530.952 memavail=7393304 print_time=6874.704 buffer_time=2.270 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 58 Hz
Stats 6850.8: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32978247 bytes_read=5079642 bytes_retransmit=9 bytes_invalid=0 send_seq=621285 receive_seq=621285 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=2406 freq=400015903 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42394 bytes_read=132558 bytes_retransmit=0 bytes_invalid=0 send_seq=7037 receive_seq=7037 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999409 adj=49997356 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213044 bytes_read=6923106 bytes_retransmit=9 bytes_invalid=0 send_seq=29781 receive_seq=29781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997670 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141216 bytes_read=3888394 bytes_retransmit=9 bytes_invalid=0 send_seq=19618 receive_seq=19618 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997435 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42661 bytes_read=1749428 bytes_retransmit=9 bytes_invalid=0 send_seq=7051 receive_seq=7051 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997591 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43147 bytes_read=129949 bytes_retransmit=9 bytes_invalid=0 send_seq=7038 receive_seq=7038 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999426 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97239 bytes_read=2664718 bytes_retransmit=0 bytes_invalid=0 send_seq=11597 receive_seq=11597 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998623 coil_temp=16.8 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.3 th2: temp=63.0 th3: temp=60.4 sysload=0.14 cputime=531.052 memavail=7393304 print_time=6875.595 buffer_time=2.159 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 59 Hz
Stats 6851.8: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=32984036 bytes_read=5080482 bytes_retransmit=9 bytes_invalid=0 send_seq=621391 receive_seq=621391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=47 upcoming_bytes=1267 freq=400015906 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42400 bytes_read=132574 bytes_retransmit=0 bytes_invalid=0 send_seq=7038 receive_seq=7038 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999408 adj=49997339 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213050 bytes_read=6923206 bytes_retransmit=9 bytes_invalid=0 send_seq=29782 receive_seq=29782 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997640 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141292 bytes_read=3891452 bytes_retransmit=9 bytes_invalid=0 send_seq=19629 receive_seq=19629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997421 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42667 bytes_read=1749662 bytes_retransmit=9 bytes_invalid=0 send_seq=7052 receive_seq=7052 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43153 bytes_read=129975 bytes_retransmit=9 bytes_invalid=0 send_seq=7039 receive_seq=7039 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999426 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97245 bytes_read=2665074 bytes_retransmit=0 bytes_invalid=0 send_seq=11598 receive_seq=11598 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998676 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.1 th2: temp=63.1 th3: temp=60.4 sysload=0.14 cputime=531.157 memavail=7393304 print_time=6876.520 buffer_time=2.081 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 60 Hz
Stats 6852.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=32989872 bytes_read=5081392 bytes_retransmit=9 bytes_invalid=0 send_seq=621502 receive_seq=621502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=44 upcoming_bytes=2034 freq=400015902 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42406 bytes_read=132590 bytes_retransmit=0 bytes_invalid=0 send_seq=7039 receive_seq=7039 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999408 adj=49997330 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213056 bytes_read=6923348 bytes_retransmit=9 bytes_invalid=0 send_seq=29783 receive_seq=29783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997613 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141368 bytes_read=3894542 bytes_retransmit=9 bytes_invalid=0 send_seq=19640 receive_seq=19640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997442 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42673 bytes_read=1749896 bytes_retransmit=9 bytes_invalid=0 send_seq=7053 receive_seq=7053 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43159 bytes_read=129990 bytes_retransmit=9 bytes_invalid=0 send_seq=7040 receive_seq=7040 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97251 bytes_read=2665430 bytes_retransmit=0 bytes_invalid=0 send_seq=11599 receive_seq=11599 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998661 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.4 th2: temp=63.1 th3: temp=60.6 sysload=0.14 cputime=531.275 memavail=7393304 print_time=6877.724 buffer_time=2.282 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 61 Hz
Stats 6853.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=32994730 bytes_read=5082167 bytes_retransmit=9 bytes_invalid=0 send_seq=621595 receive_seq=621595 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=2636 freq=400015890 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42412 bytes_read=132606 bytes_retransmit=0 bytes_invalid=0 send_seq=7040 receive_seq=7040 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999407 adj=49997361 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213062 bytes_read=6923448 bytes_retransmit=9 bytes_invalid=0 send_seq=29784 receive_seq=29784 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997670 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141444 bytes_read=3897671 bytes_retransmit=9 bytes_invalid=0 send_seq=19651 receive_seq=19651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42679 bytes_read=1750190 bytes_retransmit=9 bytes_invalid=0 send_seq=7054 receive_seq=7054 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43165 bytes_read=130005 bytes_retransmit=9 bytes_invalid=0 send_seq=7041 receive_seq=7041 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97257 bytes_read=2665786 bytes_retransmit=0 bytes_invalid=0 send_seq=11600 receive_seq=11600 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998656 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.1 th2: temp=63.0 th3: temp=60.5 sysload=0.14 cputime=531.382 memavail=7393304 print_time=6878.606 buffer_time=2.161 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 62 Hz
Stats 6854.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=33000640 bytes_read=5083027 bytes_retransmit=9 bytes_invalid=0 send_seq=621705 receive_seq=621705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=1454 freq=400015889 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42418 bytes_read=132622 bytes_retransmit=0 bytes_invalid=0 send_seq=7041 receive_seq=7041 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999407 adj=49997386 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213068 bytes_read=6923548 bytes_retransmit=9 bytes_invalid=0 send_seq=29785 receive_seq=29785 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997697 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141520 bytes_read=3900730 bytes_retransmit=9 bytes_invalid=0 send_seq=19662 receive_seq=19662 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997502 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42685 bytes_read=1750439 bytes_retransmit=9 bytes_invalid=0 send_seq=7055 receive_seq=7055 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43171 bytes_read=130020 bytes_retransmit=9 bytes_invalid=0 send_seq=7042 receive_seq=7042 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97263 bytes_read=2666142 bytes_retransmit=0 bytes_invalid=0 send_seq=11601 receive_seq=11601 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998659 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.2 th2: temp=63.1 th3: temp=60.4 sysload=0.14 cputime=531.494 memavail=7393316 print_time=6879.523 buffer_time=2.076 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 63 Hz
Stats 6855.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=33006562 bytes_read=5083926 bytes_retransmit=9 bytes_invalid=0 send_seq=621817 receive_seq=621817 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=2391 freq=400015879 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42424 bytes_read=132651 bytes_retransmit=0 bytes_invalid=0 send_seq=7042 receive_seq=7042 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999407 adj=49997385 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213074 bytes_read=6923676 bytes_retransmit=9 bytes_invalid=0 send_seq=29786 receive_seq=29786 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997702 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141596 bytes_read=3903802 bytes_retransmit=9 bytes_invalid=0 send_seq=19673 receive_seq=19673 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997499 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42691 bytes_read=1750673 bytes_retransmit=9 bytes_invalid=0 send_seq=7056 receive_seq=7056 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43177 bytes_read=130035 bytes_retransmit=9 bytes_invalid=0 send_seq=7043 receive_seq=7043 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97269 bytes_read=2666498 bytes_retransmit=0 bytes_invalid=0 send_seq=11602 receive_seq=11602 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998650 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.2 th2: temp=63.1 th3: temp=60.5 sysload=0.13 cputime=531.615 memavail=7393316 print_time=6880.737 buffer_time=2.288 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 64 Hz
Stats 6856.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=33011540 bytes_read=5084696 bytes_retransmit=9 bytes_invalid=0 send_seq=621909 receive_seq=621909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=2956 freq=400015883 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42430 bytes_read=132667 bytes_retransmit=0 bytes_invalid=0 send_seq=7043 receive_seq=7043 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999407 adj=49997412 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213080 bytes_read=6923776 bytes_retransmit=9 bytes_invalid=0 send_seq=29787 receive_seq=29787 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997739 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141672 bytes_read=3906874 bytes_retransmit=9 bytes_invalid=0 send_seq=19684 receive_seq=19684 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42697 bytes_read=1750967 bytes_retransmit=9 bytes_invalid=0 send_seq=7057 receive_seq=7057 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43183 bytes_read=130061 bytes_retransmit=9 bytes_invalid=0 send_seq=7044 receive_seq=7044 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97275 bytes_read=2666854 bytes_retransmit=0 bytes_invalid=0 send_seq=11603 receive_seq=11603 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998666 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.3 th2: temp=63.1 th3: temp=60.5 sysload=0.13 cputime=531.722 memavail=7393340 print_time=6881.622 buffer_time=2.172 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 65 Hz
Stats 6857.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33017555 bytes_read=5085596 bytes_retransmit=9 bytes_invalid=0 send_seq=622021 receive_seq=622021 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=1954 freq=400015884 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42436 bytes_read=132683 bytes_retransmit=0 bytes_invalid=0 send_seq=7044 receive_seq=7044 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999406 adj=49997405 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213086 bytes_read=6923876 bytes_retransmit=9 bytes_invalid=0 send_seq=29788 receive_seq=29788 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997698 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141748 bytes_read=3909952 bytes_retransmit=9 bytes_invalid=0 send_seq=19695 receive_seq=19695 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997525 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42703 bytes_read=1751201 bytes_retransmit=9 bytes_invalid=0 send_seq=7058 receive_seq=7058 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43189 bytes_read=130076 bytes_retransmit=9 bytes_invalid=0 send_seq=7045 receive_seq=7045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97281 bytes_read=2667210 bytes_retransmit=0 bytes_invalid=0 send_seq=11604 receive_seq=11604 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998659 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.3 th2: temp=63.1 th3: temp=60.6 sysload=0.13 cputime=531.837 memavail=7389056 print_time=6882.545 buffer_time=2.094 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 66 Hz
Stats 6858.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33023713 bytes_read=5086491 bytes_retransmit=9 bytes_invalid=0 send_seq=622135 receive_seq=622135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=2801 freq=400015886 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42442 bytes_read=132699 bytes_retransmit=0 bytes_invalid=0 send_seq=7045 receive_seq=7045 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999405 adj=49997393 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213092 bytes_read=6924018 bytes_retransmit=9 bytes_invalid=0 send_seq=29789 receive_seq=29789 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997668 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141824 bytes_read=3913036 bytes_retransmit=9 bytes_invalid=0 send_seq=19706 receive_seq=19706 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42709 bytes_read=1751435 bytes_retransmit=9 bytes_invalid=0 send_seq=7059 receive_seq=7059 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43195 bytes_read=130091 bytes_retransmit=9 bytes_invalid=0 send_seq=7046 receive_seq=7046 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97287 bytes_read=2667566 bytes_retransmit=0 bytes_invalid=0 send_seq=11605 receive_seq=11605 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998656 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.0 th2: temp=63.4 th3: temp=60.5 sysload=0.13 cputime=531.964 memavail=7396868 print_time=6883.752 buffer_time=2.301 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 67 Hz
Stats 6859.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33028864 bytes_read=5087279 bytes_retransmit=9 bytes_invalid=0 send_seq=622231 receive_seq=622231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=3264 freq=400015894 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42448 bytes_read=132715 bytes_retransmit=0 bytes_invalid=0 send_seq=7046 receive_seq=7046 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999406 adj=49997387 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213098 bytes_read=6924118 bytes_retransmit=9 bytes_invalid=0 send_seq=29790 receive_seq=29790 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997739 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141900 bytes_read=3916152 bytes_retransmit=9 bytes_invalid=0 send_seq=19717 receive_seq=19717 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997514 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42715 bytes_read=1751744 bytes_retransmit=9 bytes_invalid=0 send_seq=7060 receive_seq=7060 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43201 bytes_read=130106 bytes_retransmit=9 bytes_invalid=0 send_seq=7047 receive_seq=7047 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97293 bytes_read=2667922 bytes_retransmit=0 bytes_invalid=0 send_seq=11606 receive_seq=11606 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998650 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.1 th2: temp=63.1 th3: temp=60.5 sysload=0.13 cputime=532.070 memavail=7396620 print_time=6884.628 buffer_time=2.176 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 68 Hz
Stats 6860.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33035051 bytes_read=5088178 bytes_retransmit=9 bytes_invalid=0 send_seq=622347 receive_seq=622347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=2186 freq=400015917 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42454 bytes_read=132744 bytes_retransmit=0 bytes_invalid=0 send_seq=7047 receive_seq=7047 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999406 adj=49997397 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213104 bytes_read=6924218 bytes_retransmit=9 bytes_invalid=0 send_seq=29791 receive_seq=29791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997689 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=141976 bytes_read=3919209 bytes_retransmit=9 bytes_invalid=0 send_seq=19728 receive_seq=19728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997507 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42721 bytes_read=1751978 bytes_retransmit=9 bytes_invalid=0 send_seq=7061 receive_seq=7061 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43207 bytes_read=130121 bytes_retransmit=9 bytes_invalid=0 send_seq=7048 receive_seq=7048 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97299 bytes_read=2668278 bytes_retransmit=0 bytes_invalid=0 send_seq=11607 receive_seq=11607 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998642 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.1 th2: temp=63.2 th3: temp=60.6 sysload=0.12 cputime=532.183 memavail=7396396 print_time=6885.549 buffer_time=2.096 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 69 Hz
Stats 6861.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33041302 bytes_read=5089078 bytes_retransmit=9 bytes_invalid=0 send_seq=622462 receive_seq=622462 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=39 upcoming_bytes=3137 freq=400015914 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42460 bytes_read=132760 bytes_retransmit=0 bytes_invalid=0 send_seq=7048 receive_seq=7048 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999406 adj=49997360 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213110 bytes_read=6924346 bytes_retransmit=9 bytes_invalid=0 send_seq=29792 receive_seq=29792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997623 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=142052 bytes_read=3922294 bytes_retransmit=9 bytes_invalid=0 send_seq=19739 receive_seq=19739 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997461 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42727 bytes_read=1752212 bytes_retransmit=9 bytes_invalid=0 send_seq=7062 receive_seq=7062 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997588 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43213 bytes_read=130147 bytes_retransmit=9 bytes_invalid=0 send_seq=7049 receive_seq=7049 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999422 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97305 bytes_read=2668634 bytes_retransmit=0 bytes_invalid=0 send_seq=11608 receive_seq=11608 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998620 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.2 th2: temp=63.2 th3: temp=60.5 sysload=0.12 cputime=532.304 memavail=7396396 print_time=6886.758 buffer_time=2.305 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 70 Hz
Stats 6862.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33046562 bytes_read=5089889 bytes_retransmit=9 bytes_invalid=0 send_seq=622559 receive_seq=622559 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=3636 freq=400015913 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42466 bytes_read=132776 bytes_retransmit=0 bytes_invalid=0 send_seq=7049 receive_seq=7049 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999408 adj=49997380 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213116 bytes_read=6924446 bytes_retransmit=9 bytes_invalid=0 send_seq=29793 receive_seq=29793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997648 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=142128 bytes_read=3925368 bytes_retransmit=9 bytes_invalid=0 send_seq=19750 receive_seq=19750 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997477 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42733 bytes_read=1752506 bytes_retransmit=9 bytes_invalid=0 send_seq=7063 receive_seq=7063 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997607 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43219 bytes_read=130162 bytes_retransmit=9 bytes_invalid=0 send_seq=7050 receive_seq=7050 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97311 bytes_read=2668990 bytes_retransmit=0 bytes_invalid=0 send_seq=11609 receive_seq=11609 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998629 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.1 th2: temp=63.1 th3: temp=60.5 sysload=0.12 cputime=532.412 memavail=7396144 print_time=6887.643 buffer_time=2.190 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 71 Hz
Stats 6863.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33052931 bytes_read=5090803 bytes_retransmit=9 bytes_invalid=0 send_seq=622677 receive_seq=622677 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=2742 freq=400015907 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42472 bytes_read=132792 bytes_retransmit=0 bytes_invalid=0 send_seq=7050 receive_seq=7050 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999407 adj=49997410 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213122 bytes_read=6924560 bytes_retransmit=9 bytes_invalid=0 send_seq=29794 receive_seq=29794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997650 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=142204 bytes_read=3928424 bytes_retransmit=9 bytes_invalid=0 send_seq=19761 receive_seq=19761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42739 bytes_read=1752740 bytes_retransmit=9 bytes_invalid=0 send_seq=7064 receive_seq=7064 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997610 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43225 bytes_read=130177 bytes_retransmit=9 bytes_invalid=0 send_seq=7051 receive_seq=7051 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97317 bytes_read=2669346 bytes_retransmit=0 bytes_invalid=0 send_seq=11610 receive_seq=11610 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998684 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.3 th2: temp=63.3 th3: temp=60.5 sysload=0.12 cputime=532.522 memavail=7396144 print_time=6888.567 buffer_time=2.112 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 72 Hz
Stats 6864.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33059392 bytes_read=5091728 bytes_retransmit=9 bytes_invalid=0 send_seq=622797 receive_seq=622797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=3587 freq=400015908 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42478 bytes_read=132808 bytes_retransmit=0 bytes_invalid=0 send_seq=7051 receive_seq=7051 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999406 adj=49997407 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213128 bytes_read=6924688 bytes_retransmit=9 bytes_invalid=0 send_seq=29795 receive_seq=29795 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997638 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=142280 bytes_read=3931568 bytes_retransmit=9 bytes_invalid=0 send_seq=19772 receive_seq=19772 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42745 bytes_read=1752989 bytes_retransmit=9 bytes_invalid=0 send_seq=7065 receive_seq=7065 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43231 bytes_read=130192 bytes_retransmit=9 bytes_invalid=0 send_seq=7052 receive_seq=7052 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97323 bytes_read=2669702 bytes_retransmit=0 bytes_invalid=0 send_seq=11611 receive_seq=11611 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998683 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.3 th2: temp=63.0 th3: temp=60.5 sysload=0.12 cputime=532.644 memavail=7396144 print_time=6889.771 buffer_time=2.309 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 73 Hz
Stats 6865.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33064948 bytes_read=5092553 bytes_retransmit=9 bytes_invalid=0 send_seq=622900 receive_seq=622900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=3874 freq=400015911 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42484 bytes_read=132837 bytes_retransmit=0 bytes_invalid=0 send_seq=7052 receive_seq=7052 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999405 adj=49997393 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213134 bytes_read=6924788 bytes_retransmit=9 bytes_invalid=0 send_seq=29796 receive_seq=29796 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997627 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=142356 bytes_read=3934625 bytes_retransmit=9 bytes_invalid=0 send_seq=19783 receive_seq=19783 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42751 bytes_read=1753278 bytes_retransmit=9 bytes_invalid=0 send_seq=7066 receive_seq=7066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43237 bytes_read=130207 bytes_retransmit=9 bytes_invalid=0 send_seq=7053 receive_seq=7053 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97329 bytes_read=2670058 bytes_retransmit=0 bytes_invalid=0 send_seq=11612 receive_seq=11612 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998668 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.2 th2: temp=63.2 th3: temp=60.7 sysload=0.11 cputime=532.752 memavail=7396148 print_time=6890.654 buffer_time=2.191 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 74 Hz
Stats 6866.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33071293 bytes_read=5093477 bytes_retransmit=9 bytes_invalid=0 send_seq=623017 receive_seq=623017 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=3275 freq=400015913 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42490 bytes_read=132853 bytes_retransmit=0 bytes_invalid=0 send_seq=7053 receive_seq=7053 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999405 adj=49997379 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213140 bytes_read=6924888 bytes_retransmit=9 bytes_invalid=0 send_seq=29797 receive_seq=29797 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997605 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=142432 bytes_read=3937682 bytes_retransmit=9 bytes_invalid=0 send_seq=19794 receive_seq=19794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42757 bytes_read=1753496 bytes_retransmit=9 bytes_invalid=0 send_seq=7067 receive_seq=7067 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997614 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43243 bytes_read=130234 bytes_retransmit=9 bytes_invalid=0 send_seq=7054 receive_seq=7054 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97335 bytes_read=2670414 bytes_retransmit=0 bytes_invalid=0 send_seq=11613 receive_seq=11613 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998657 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.2 th2: temp=63.3 th3: temp=60.5 sysload=0.11 cputime=532.867 memavail=7396148 print_time=6891.587 buffer_time=2.124 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 75 Hz
Stats 6867.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33077964 bytes_read=5094408 bytes_retransmit=9 bytes_invalid=0 send_seq=623138 receive_seq=623138 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=4059 freq=400015948 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42496 bytes_read=132869 bytes_retransmit=0 bytes_invalid=0 send_seq=7054 receive_seq=7054 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999405 adj=49997390 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213146 bytes_read=6925016 bytes_retransmit=9 bytes_invalid=0 send_seq=29798 receive_seq=29798 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997722 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=142508 bytes_read=3940786 bytes_retransmit=9 bytes_invalid=0 send_seq=19805 receive_seq=19805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42763 bytes_read=1753714 bytes_retransmit=9 bytes_invalid=0 send_seq=7068 receive_seq=7068 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997616 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43249 bytes_read=130250 bytes_retransmit=9 bytes_invalid=0 send_seq=7055 receive_seq=7055 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97341 bytes_read=2670770 bytes_retransmit=0 bytes_invalid=0 send_seq=11614 receive_seq=11614 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998648 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.1 th2: temp=63.2 th3: temp=60.5 sysload=0.11 cputime=532.991 memavail=7394648 print_time=6892.789 buffer_time=2.319 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 76 Hz
Stats 6868.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33083589 bytes_read=5095248 bytes_retransmit=9 bytes_invalid=0 send_seq=623244 receive_seq=623244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=55 upcoming_bytes=4181 freq=400015937 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42502 bytes_read=132885 bytes_retransmit=0 bytes_invalid=0 send_seq=7055 receive_seq=7055 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999405 adj=49997348 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213152 bytes_read=6925130 bytes_retransmit=9 bytes_invalid=0 send_seq=29799 receive_seq=29799 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997625 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=142584 bytes_read=3943844 bytes_retransmit=9 bytes_invalid=0 send_seq=19816 receive_seq=19816 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997447 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=42769 bytes_read=1753988 bytes_retransmit=9 bytes_invalid=0 send_seq=7069 receive_seq=7069 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997570 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43255 bytes_read=130266 bytes_retransmit=9 bytes_invalid=0 send_seq=7056 receive_seq=7056 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999425 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97347 bytes_read=2671126 bytes_retransmit=0 bytes_invalid=0 send_seq=11615 receive_seq=11615 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998616 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.2 th2: temp=63.3 th3: temp=60.6 sysload=0.11 cputime=533.100 memavail=7394444 print_time=6893.660 buffer_time=2.189 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 77 Hz
Stats 6869.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33090131 bytes_read=5096192 bytes_retransmit=9 bytes_invalid=0 send_seq=623365 receive_seq=623365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=3716 freq=400016007 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42508 bytes_read=132901 bytes_retransmit=0 bytes_invalid=0 send_seq=7056 receive_seq=7056 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999405 adj=49997369 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213158 bytes_read=6925230 bytes_retransmit=9 bytes_invalid=0 send_seq=29800 receive_seq=29800 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997626 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=142660 bytes_read=3946959 bytes_retransmit=9 bytes_invalid=0 send_seq=19827 receive_seq=19827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997484 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42775 bytes_read=1754221 bytes_retransmit=9 bytes_invalid=0 send_seq=7070 receive_seq=7070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997589 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43261 bytes_read=130282 bytes_retransmit=9 bytes_invalid=0 send_seq=7057 receive_seq=7057 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97353 bytes_read=2671482 bytes_retransmit=0 bytes_invalid=0 send_seq=11616 receive_seq=11616 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998629 coil_temp=16.8 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.2 th2: temp=63.2 th3: temp=60.6 sysload=0.11 cputime=533.216 memavail=7394448 print_time=6894.599 buffer_time=2.127 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 78 Hz
Stats 6870.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33096991 bytes_read=5097123 bytes_retransmit=9 bytes_invalid=0 send_seq=623490 receive_seq=623490 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=4708 freq=400016001 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42514 bytes_read=132930 bytes_retransmit=0 bytes_invalid=0 send_seq=7057 receive_seq=7057 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999404 adj=49997259 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213164 bytes_read=6925358 bytes_retransmit=9 bytes_invalid=0 send_seq=29801 receive_seq=29801 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997470 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=142736 bytes_read=3950045 bytes_retransmit=9 bytes_invalid=0 send_seq=19838 receive_seq=19838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997344 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42781 bytes_read=1754453 bytes_retransmit=9 bytes_invalid=0 send_seq=7071 receive_seq=7071 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997486 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43267 bytes_read=130298 bytes_retransmit=9 bytes_invalid=0 send_seq=7058 receive_seq=7058 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999412 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97359 bytes_read=2671838 bytes_retransmit=0 bytes_invalid=0 send_seq=11617 receive_seq=11617 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998561 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.3 th2: temp=63.2 th3: temp=60.6 sysload=0.10 cputime=533.341 memavail=7394448 print_time=6895.809 buffer_time=2.328 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 79 Hz
Stats 6871.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33102907 bytes_read=5097977 bytes_retransmit=9 bytes_invalid=0 send_seq=623599 receive_seq=623599 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=4374 freq=400016022 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42520 bytes_read=132946 bytes_retransmit=0 bytes_invalid=0 send_seq=7058 receive_seq=7058 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999403 adj=49997301 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213170 bytes_read=6925458 bytes_retransmit=9 bytes_invalid=0 send_seq=29802 receive_seq=29802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997529 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=142812 bytes_read=3953102 bytes_retransmit=9 bytes_invalid=0 send_seq=19849 receive_seq=19849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997398 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42787 bytes_read=1754728 bytes_retransmit=9 bytes_invalid=0 send_seq=7072 receive_seq=7072 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997532 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43273 bytes_read=130325 bytes_retransmit=9 bytes_invalid=0 send_seq=7059 receive_seq=7059 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999419 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97365 bytes_read=2672194 bytes_retransmit=0 bytes_invalid=0 send_seq=11618 receive_seq=11618 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998590 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.2 th2: temp=63.2 th3: temp=60.6 sysload=0.10 cputime=533.453 memavail=7394448 print_time=6896.676 buffer_time=2.194 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 80 Hz
Stats 6872.8: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33109547 bytes_read=5098937 bytes_retransmit=9 bytes_invalid=0 send_seq=623720 receive_seq=623720 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=3965 freq=400016083 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42526 bytes_read=132962 bytes_retransmit=0 bytes_invalid=0 send_seq=7059 receive_seq=7059 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999403 adj=49997266 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213176 bytes_read=6925558 bytes_retransmit=9 bytes_invalid=0 send_seq=29803 receive_seq=29803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997487 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=142888 bytes_read=3956176 bytes_retransmit=9 bytes_invalid=0 send_seq=19860 receive_seq=19860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997366 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42793 bytes_read=1754962 bytes_retransmit=9 bytes_invalid=0 send_seq=7073 receive_seq=7073 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997508 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43279 bytes_read=130341 bytes_retransmit=9 bytes_invalid=0 send_seq=7060 receive_seq=7060 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999412 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97371 bytes_read=2672550 bytes_retransmit=0 bytes_invalid=0 send_seq=11619 receive_seq=11619 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998589 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.3 th2: temp=63.2 th3: temp=60.6 sysload=0.10 cputime=533.572 memavail=7394448 print_time=6897.607 buffer_time=2.125 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 81 Hz
Stats 6873.8: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33116511 bytes_read=5099882 bytes_retransmit=9 bytes_invalid=0 send_seq=623847 receive_seq=623847 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=4996 freq=400016070 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42532 bytes_read=132978 bytes_retransmit=0 bytes_invalid=0 send_seq=7060 receive_seq=7060 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999407 adj=49997193 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213182 bytes_read=6925700 bytes_retransmit=9 bytes_invalid=0 send_seq=29804 receive_seq=29804 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997389 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=142964 bytes_read=3959318 bytes_retransmit=9 bytes_invalid=0 send_seq=19871 receive_seq=19871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997262 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42799 bytes_read=1755241 bytes_retransmit=9 bytes_invalid=0 send_seq=7074 receive_seq=7074 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997432 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43285 bytes_read=130357 bytes_retransmit=9 bytes_invalid=0 send_seq=7061 receive_seq=7061 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999391 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97377 bytes_read=2672906 bytes_retransmit=0 bytes_invalid=0 send_seq=11620 receive_seq=11620 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998537 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.1 th2: temp=63.3 th3: temp=60.6 sysload=0.10 cputime=533.699 memavail=7394464 print_time=6898.815 buffer_time=2.324 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 82 Hz
Stats 6874.8: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33122564 bytes_read=5100747 bytes_retransmit=9 bytes_invalid=0 send_seq=623958 receive_seq=623958 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=35 upcoming_bytes=4552 freq=400016049 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42538 bytes_read=132994 bytes_retransmit=0 bytes_invalid=0 send_seq=7061 receive_seq=7061 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999407 adj=49997317 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213188 bytes_read=6925800 bytes_retransmit=9 bytes_invalid=0 send_seq=29805 receive_seq=29805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997474 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=143033 bytes_read=3962352 bytes_retransmit=9 bytes_invalid=0 send_seq=19881 receive_seq=19881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997345 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42805 bytes_read=1755505 bytes_retransmit=9 bytes_invalid=0 send_seq=7075 receive_seq=7075 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997502 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43291 bytes_read=130373 bytes_retransmit=9 bytes_invalid=0 send_seq=7062 receive_seq=7062 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999406 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97383 bytes_read=2673262 bytes_retransmit=0 bytes_invalid=0 send_seq=11621 receive_seq=11621 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998575 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.0 th2: temp=63.2 th3: temp=60.5 sysload=0.10 cputime=533.811 memavail=7394464 print_time=6899.684 buffer_time=2.191 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 83 Hz
Stats 6875.8: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33129363 bytes_read=5101706 bytes_retransmit=9 bytes_invalid=0 send_seq=624082 receive_seq=624082 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=4179 freq=400016031 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42544 bytes_read=133023 bytes_retransmit=0 bytes_invalid=0 send_seq=7062 receive_seq=7062 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999407 adj=49997355 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213194 bytes_read=6925900 bytes_retransmit=9 bytes_invalid=0 send_seq=29806 receive_seq=29806 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997588 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=143109 bytes_read=3965409 bytes_retransmit=9 bytes_invalid=0 send_seq=19892 receive_seq=19892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997397 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42811 bytes_read=1755739 bytes_retransmit=9 bytes_invalid=0 send_seq=7076 receive_seq=7076 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997542 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43297 bytes_read=130389 bytes_retransmit=9 bytes_invalid=0 send_seq=7063 receive_seq=7063 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999415 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97389 bytes_read=2673618 bytes_retransmit=0 bytes_invalid=0 send_seq=11622 receive_seq=11622 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998600 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.3 th2: temp=63.1 th3: temp=60.5 sysload=0.09 cputime=533.940 memavail=7394872 print_time=6900.621 buffer_time=2.128 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 84 Hz
Stats 6876.8: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33136326 bytes_read=5102657 bytes_retransmit=9 bytes_invalid=0 send_seq=624208 receive_seq=624208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=47 upcoming_bytes=5157 freq=400016070 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42556 bytes_read=133055 bytes_retransmit=0 bytes_invalid=0 send_seq=7064 receive_seq=7064 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999406 adj=49997393 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213206 bytes_read=6926044 bytes_retransmit=9 bytes_invalid=0 send_seq=29808 receive_seq=29808 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997614 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=143191 bytes_read=3968567 bytes_retransmit=9 bytes_invalid=0 send_seq=19904 receive_seq=19904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997449 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42823 bytes_read=1756049 bytes_retransmit=9 bytes_invalid=0 send_seq=7078 receive_seq=7078 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997593 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43309 bytes_read=130432 bytes_retransmit=9 bytes_invalid=0 send_seq=7065 receive_seq=7065 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999425 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97401 bytes_read=2673990 bytes_retransmit=0 bytes_invalid=0 send_seq=11624 receive_seq=11624 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998629 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.1 th2: temp=63.3 th3: temp=60.7 sysload=0.09 cputime=534.067 memavail=7394872 print_time=6901.824 buffer_time=2.321 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 85 Hz
Stats 6877.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33142514 bytes_read=5103558 bytes_retransmit=9 bytes_invalid=0 send_seq=624323 receive_seq=624323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=4655 freq=400016051 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42562 bytes_read=133071 bytes_retransmit=0 bytes_invalid=0 send_seq=7065 receive_seq=7065 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999406 adj=49997330 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213212 bytes_read=6926144 bytes_retransmit=9 bytes_invalid=0 send_seq=29809 receive_seq=29809 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997527 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=143267 bytes_read=3971641 bytes_retransmit=9 bytes_invalid=0 send_seq=19915 receive_seq=19915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997390 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42829 bytes_read=1756283 bytes_retransmit=9 bytes_invalid=0 send_seq=7079 receive_seq=7079 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997543 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43315 bytes_read=130448 bytes_retransmit=9 bytes_invalid=0 send_seq=7066 receive_seq=7066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999412 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97407 bytes_read=2674346 bytes_retransmit=0 bytes_invalid=0 send_seq=11625 receive_seq=11625 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998612 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.3 th2: temp=63.4 th3: temp=60.6 sysload=0.09 cputime=534.182 memavail=7395164 print_time=6902.683 buffer_time=2.178 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 86 Hz
Stats 6878.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33149136 bytes_read=5104507 bytes_retransmit=9 bytes_invalid=0 send_seq=624445 receive_seq=624445 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=4658 freq=400016044 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42568 bytes_read=133087 bytes_retransmit=0 bytes_invalid=0 send_seq=7066 receive_seq=7066 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999405 adj=49997364 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213218 bytes_read=6926258 bytes_retransmit=9 bytes_invalid=0 send_seq=29810 receive_seq=29810 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997557 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=143343 bytes_read=3974700 bytes_retransmit=9 bytes_invalid=0 send_seq=19926 receive_seq=19926 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42835 bytes_read=1756517 bytes_retransmit=9 bytes_invalid=0 send_seq=7080 receive_seq=7080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997577 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43321 bytes_read=130464 bytes_retransmit=9 bytes_invalid=0 send_seq=7067 receive_seq=7067 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999420 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97413 bytes_read=2674702 bytes_retransmit=0 bytes_invalid=0 send_seq=11626 receive_seq=11626 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998626 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.3 th2: temp=63.2 th3: temp=60.6 sysload=0.09 cputime=534.297 memavail=7395164 print_time=6903.622 buffer_time=2.117 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 87 Hz
Stats 6879.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33156539 bytes_read=5105492 bytes_retransmit=9 bytes_invalid=0 send_seq=624580 receive_seq=624580 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=5476 freq=400016039 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42574 bytes_read=133102 bytes_retransmit=0 bytes_invalid=0 send_seq=7067 receive_seq=7067 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999405 adj=49997365 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213224 bytes_read=6926386 bytes_retransmit=9 bytes_invalid=0 send_seq=29811 receive_seq=29811 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997577 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=143419 bytes_read=3977785 bytes_retransmit=9 bytes_invalid=0 send_seq=19937 receive_seq=19937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42841 bytes_read=1756826 bytes_retransmit=9 bytes_invalid=0 send_seq=7081 receive_seq=7081 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997604 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43327 bytes_read=130480 bytes_retransmit=9 bytes_invalid=0 send_seq=7068 receive_seq=7068 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999423 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97419 bytes_read=2675058 bytes_retransmit=0 bytes_invalid=0 send_seq=11627 receive_seq=11627 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998659 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.4 th2: temp=63.2 th3: temp=60.5 sysload=0.09 cputime=534.425 memavail=7394940 print_time=6904.827 buffer_time=2.319 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 88 Hz
Stats 6880.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33162932 bytes_read=5106402 bytes_retransmit=9 bytes_invalid=0 send_seq=624700 receive_seq=624700 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=4760 freq=400016012 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=42580 bytes_read=133130 bytes_retransmit=0 bytes_invalid=0 send_seq=7068 receive_seq=7068 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999405 adj=49997381 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213230 bytes_read=6926486 bytes_retransmit=9 bytes_invalid=0 send_seq=29812 receive_seq=29812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997606 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=143495 bytes_read=3980900 bytes_retransmit=9 bytes_invalid=0 send_seq=19948 receive_seq=19948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997521 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42847 bytes_read=1757060 bytes_retransmit=9 bytes_invalid=0 send_seq=7082 receive_seq=7082 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43333 bytes_read=130496 bytes_retransmit=9 bytes_invalid=0 send_seq=7069 receive_seq=7069 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999428 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97425 bytes_read=2675414 bytes_retransmit=0 bytes_invalid=0 send_seq=11628 receive_seq=11628 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998653 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.2 th2: temp=63.1 th3: temp=60.6 sysload=0.08 cputime=534.539 memavail=7394940 print_time=6905.696 buffer_time=2.187 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 89 Hz
Stats 6881.8: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33169763 bytes_read=5107361 bytes_retransmit=9 bytes_invalid=0 send_seq=624825 receive_seq=624825 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=4719 freq=400016021 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=42586 bytes_read=133145 bytes_retransmit=0 bytes_invalid=0 send_seq=7069 receive_seq=7069 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999404 adj=49997428 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213236 bytes_read=6926586 bytes_retransmit=9 bytes_invalid=0 send_seq=29813 receive_seq=29813 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997789 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=143571 bytes_read=3983959 bytes_retransmit=9 bytes_invalid=0 send_seq=19959 receive_seq=19959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42853 bytes_read=1757294 bytes_retransmit=9 bytes_invalid=0 send_seq=7083 receive_seq=7083 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999571 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43339 bytes_read=130523 bytes_retransmit=9 bytes_invalid=0 send_seq=7070 receive_seq=7070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97431 bytes_read=2675770 bytes_retransmit=0 bytes_invalid=0 send_seq=11629 receive_seq=11629 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998673 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.1 th2: temp=63.1 th3: temp=60.6 sysload=0.08 cputime=534.655 memavail=7394940 print_time=6906.634 buffer_time=2.124 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 90 Hz
Stats 6882.8: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33176979 bytes_read=5108337 bytes_retransmit=9 bytes_invalid=0 send_seq=624955 receive_seq=624955 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=5649 freq=400016238 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=42592 bytes_read=133160 bytes_retransmit=0 bytes_invalid=0 send_seq=7070 receive_seq=7070 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999403 adj=49997401 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213242 bytes_read=6926714 bytes_retransmit=9 bytes_invalid=0 send_seq=29814 receive_seq=29814 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000257 adj=63997752 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=143647 bytes_read=3987062 bytes_retransmit=9 bytes_invalid=0 send_seq=19970 receive_seq=19970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997544 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42859 bytes_read=1757588 bytes_retransmit=9 bytes_invalid=0 send_seq=7084 receive_seq=7084 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999570 adj=47997849 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43345 bytes_read=130539 bytes_retransmit=9 bytes_invalid=0 send_seq=7071 receive_seq=7071 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97437 bytes_read=2676144 bytes_retransmit=0 bytes_invalid=0 send_seq=11630 receive_seq=11630 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998665 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.3 th2: temp=63.1 th3: temp=60.7 sysload=0.08 cputime=534.783 memavail=7394940 print_time=6907.829 buffer_time=2.312 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 91 Hz
Stats 6883.8: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33183548 bytes_read=5109252 bytes_retransmit=9 bytes_invalid=0 send_seq=625076 receive_seq=625076 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=4876 freq=400016244 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=42598 bytes_read=133175 bytes_retransmit=0 bytes_invalid=0 send_seq=7071 receive_seq=7071 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999401 adj=49997075 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213248 bytes_read=6926828 bytes_retransmit=9 bytes_invalid=0 send_seq=29815 receive_seq=29815 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000254 adj=63997600 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=143723 bytes_read=3990118 bytes_retransmit=9 bytes_invalid=0 send_seq=19981 receive_seq=19981 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000089 adj=63997124 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42865 bytes_read=1757822 bytes_retransmit=9 bytes_invalid=0 send_seq=7085 receive_seq=7085 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999569 adj=47997481 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43351 bytes_read=130555 bytes_retransmit=9 bytes_invalid=0 send_seq=7072 receive_seq=7072 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999370 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97443 bytes_read=2676500 bytes_retransmit=0 bytes_invalid=0 send_seq=11631 receive_seq=11631 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998464 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.3 th2: temp=63.3 th3: temp=60.5 sysload=0.08 cputime=534.899 memavail=7394940 print_time=6908.702 buffer_time=2.184 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 92 Hz
Stats 6884.8: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33190240 bytes_read=5110201 bytes_retransmit=9 bytes_invalid=0 send_seq=625198 receive_seq=625198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=5096 freq=400016233 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=42604 bytes_read=133190 bytes_retransmit=0 bytes_invalid=0 send_seq=7072 receive_seq=7072 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999401 adj=49997079 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213254 bytes_read=6926942 bytes_retransmit=9 bytes_invalid=0 send_seq=29816 receive_seq=29816 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000252 adj=63997561 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=143799 bytes_read=3993175 bytes_retransmit=9 bytes_invalid=0 send_seq=19992 receive_seq=19992 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000087 adj=63997494 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42871 bytes_read=1758071 bytes_retransmit=9 bytes_invalid=0 send_seq=7086 receive_seq=7086 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999568 adj=47997472 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43357 bytes_read=130571 bytes_retransmit=9 bytes_invalid=0 send_seq=7073 receive_seq=7073 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999373 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97449 bytes_read=2676856 bytes_retransmit=0 bytes_invalid=0 send_seq=11632 receive_seq=11632 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998480 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.3 th2: temp=63.2 th3: temp=60.6 sysload=0.08 cputime=535.014 memavail=7394940 print_time=6909.645 buffer_time=2.127 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 93 Hz
Stats 6885.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33197786 bytes_read=5111181 bytes_retransmit=9 bytes_invalid=0 send_seq=625332 receive_seq=625332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=5876 freq=400016209 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=42610 bytes_read=133219 bytes_retransmit=0 bytes_invalid=0 send_seq=7073 receive_seq=7073 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999401 adj=49997129 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213260 bytes_read=6927056 bytes_retransmit=9 bytes_invalid=0 send_seq=29817 receive_seq=29817 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000249 adj=63997568 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=143875 bytes_read=3996318 bytes_retransmit=9 bytes_invalid=0 send_seq=20003 receive_seq=20003 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000090 adj=63997495 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42877 bytes_read=1758365 bytes_retransmit=9 bytes_invalid=0 send_seq=7087 receive_seq=7087 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999571 adj=47997500 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43363 bytes_read=130587 bytes_retransmit=9 bytes_invalid=0 send_seq=7074 receive_seq=7074 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999383 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97455 bytes_read=2677212 bytes_retransmit=0 bytes_invalid=0 send_seq=11633 receive_seq=11633 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998512 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.3 th2: temp=63.4 th3: temp=60.6 sysload=0.24 cputime=535.155 memavail=7390356 print_time=6910.840 buffer_time=2.314 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 94 Hz
Stats 6886.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33204501 bytes_read=5112116 bytes_retransmit=9 bytes_invalid=0 send_seq=625457 receive_seq=625457 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=5143 freq=400016189 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=42616 bytes_read=133235 bytes_retransmit=0 bytes_invalid=0 send_seq=7074 receive_seq=7074 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999401 adj=49997241 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213266 bytes_read=6927156 bytes_retransmit=9 bytes_invalid=0 send_seq=29818 receive_seq=29818 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000245 adj=63997603 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=143951 bytes_read=3999375 bytes_retransmit=9 bytes_invalid=0 send_seq=20014 receive_seq=20014 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000088 adj=63997568 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42883 bytes_read=1758599 bytes_retransmit=9 bytes_invalid=0 send_seq=7088 receive_seq=7088 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999572 adj=47997605 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43369 bytes_read=130614 bytes_retransmit=9 bytes_invalid=0 send_seq=7075 receive_seq=7075 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999412 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97461 bytes_read=2677568 bytes_retransmit=0 bytes_invalid=0 send_seq=11634 receive_seq=11634 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998570 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.1 th2: temp=63.3 th3: temp=60.6 sysload=0.24 cputime=535.275 memavail=7393972 print_time=6911.719 buffer_time=2.193 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 95 Hz
Stats 6887.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33211222 bytes_read=5113091 bytes_retransmit=9 bytes_invalid=0 send_seq=625581 receive_seq=625581 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=5478 freq=400016164 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=42622 bytes_read=133251 bytes_retransmit=0 bytes_invalid=0 send_seq=7075 receive_seq=7075 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999403 adj=49997286 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213272 bytes_read=6927270 bytes_retransmit=9 bytes_invalid=0 send_seq=29819 receive_seq=29819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000242 adj=63997605 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=144027 bytes_read=4002451 bytes_retransmit=9 bytes_invalid=0 send_seq=20025 receive_seq=20025 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000087 adj=63997579 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42889 bytes_read=1758833 bytes_retransmit=9 bytes_invalid=0 send_seq=7089 receive_seq=7089 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999571 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43375 bytes_read=130630 bytes_retransmit=9 bytes_invalid=0 send_seq=7076 receive_seq=7076 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999421 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.1 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97467 bytes_read=2677924 bytes_retransmit=0 bytes_invalid=0 send_seq=11635 receive_seq=11635 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998603 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.3 th2: temp=63.1 th3: temp=60.7 sysload=0.24 cputime=535.394 memavail=7393216 print_time=6912.648 buffer_time=2.122 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 96 Hz
Stats 6888.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33218935 bytes_read=5114091 bytes_retransmit=9 bytes_invalid=0 send_seq=625719 receive_seq=625719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=6188 freq=400016153 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=42628 bytes_read=133267 bytes_retransmit=0 bytes_invalid=0 send_seq=7076 receive_seq=7076 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999403 adj=49997359 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213278 bytes_read=6927391 bytes_retransmit=9 bytes_invalid=0 send_seq=29820 receive_seq=29820 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997623 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=144103 bytes_read=4005583 bytes_retransmit=9 bytes_invalid=0 send_seq=20036 receive_seq=20036 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000085 adj=63997597 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42895 bytes_read=1759127 bytes_retransmit=9 bytes_invalid=0 send_seq=7090 receive_seq=7090 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999571 adj=47997669 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43381 bytes_read=130646 bytes_retransmit=9 bytes_invalid=0 send_seq=7077 receive_seq=7077 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97473 bytes_read=2678280 bytes_retransmit=0 bytes_invalid=0 send_seq=11636 receive_seq=11636 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998635 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.0 th2: temp=63.3 th3: temp=60.6 sysload=0.24 cputime=535.527 memavail=7393216 print_time=6913.841 buffer_time=2.305 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 97 Hz
Stats 6889.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33226027 bytes_read=5115051 bytes_retransmit=9 bytes_invalid=0 send_seq=625849 receive_seq=625849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=35 upcoming_bytes=5152 freq=400016158 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=42634 bytes_read=133283 bytes_retransmit=0 bytes_invalid=0 send_seq=7077 receive_seq=7077 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999403 adj=49997379 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213284 bytes_read=6927484 bytes_retransmit=9 bytes_invalid=0 send_seq=29821 receive_seq=29821 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997628 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=144179 bytes_read=4008621 bytes_retransmit=9 bytes_invalid=0 send_seq=20047 receive_seq=20047 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000083 adj=63997574 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42901 bytes_read=1759376 bytes_retransmit=9 bytes_invalid=0 send_seq=7091 receive_seq=7091 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999573 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43387 bytes_read=130662 bytes_retransmit=9 bytes_invalid=0 send_seq=7078 receive_seq=7078 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97479 bytes_read=2678636 bytes_retransmit=0 bytes_invalid=0 send_seq=11637 receive_seq=11637 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998637 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.3 th2: temp=63.2 th3: temp=60.5 sysload=0.24 cputime=535.646 memavail=7393216 print_time=6914.722 buffer_time=2.185 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 98 Hz
Stats 6890.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33232775 bytes_read=5116010 bytes_retransmit=9 bytes_invalid=0 send_seq=625973 receive_seq=625973 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=5598 freq=400016150 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=42640 bytes_read=133299 bytes_retransmit=0 bytes_invalid=0 send_seq=7078 receive_seq=7078 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999402 adj=49997375 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213290 bytes_read=6927603 bytes_retransmit=9 bytes_invalid=0 send_seq=29822 receive_seq=29822 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997602 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=144255 bytes_read=4011673 bytes_retransmit=9 bytes_invalid=0 send_seq=20058 receive_seq=20058 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000081 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42907 bytes_read=1759610 bytes_retransmit=9 bytes_invalid=0 send_seq=7092 receive_seq=7092 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999571 adj=47997685 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43393 bytes_read=130678 bytes_retransmit=9 bytes_invalid=0 send_seq=7079 receive_seq=7079 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97485 bytes_read=2678992 bytes_retransmit=0 bytes_invalid=0 send_seq=11638 receive_seq=11638 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998633 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.2 th2: temp=63.2 th3: temp=60.6 sysload=0.22 cputime=535.766 memavail=7393232 print_time=6915.650 buffer_time=2.113 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 99 Hz
Stats 6891.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33240515 bytes_read=5117025 bytes_retransmit=9 bytes_invalid=0 send_seq=626114 receive_seq=626114 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=52 upcoming_bytes=6520 freq=400016131 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42646 bytes_read=133328 bytes_retransmit=0 bytes_invalid=0 send_seq=7079 receive_seq=7079 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999402 adj=49997381 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213296 bytes_read=6927696 bytes_retransmit=9 bytes_invalid=0 send_seq=29823 receive_seq=29823 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997600 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=144331 bytes_read=4014727 bytes_retransmit=9 bytes_invalid=0 send_seq=20069 receive_seq=20069 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000079 adj=63997512 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42913 bytes_read=1759904 bytes_retransmit=9 bytes_invalid=0 send_seq=7093 receive_seq=7093 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999571 adj=47997668 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43399 bytes_read=130705 bytes_retransmit=9 bytes_invalid=0 send_seq=7080 receive_seq=7080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97491 bytes_read=2679348 bytes_retransmit=0 bytes_invalid=0 send_seq=11639 receive_seq=11639 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998637 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.3 th2: temp=63.1 th3: temp=60.5 sysload=0.22 cputime=535.901 memavail=7393232 print_time=6916.853 buffer_time=2.316 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 100 Hz
Stats 6892.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33247689 bytes_read=5118001 bytes_retransmit=9 bytes_invalid=0 send_seq=626245 receive_seq=626245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=26 upcoming_bytes=5352 freq=400016140 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42652 bytes_read=133344 bytes_retransmit=0 bytes_invalid=0 send_seq=7080 receive_seq=7080 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999409 adj=49997408 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213302 bytes_read=6927794 bytes_retransmit=9 bytes_invalid=0 send_seq=29824 receive_seq=29824 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997659 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=144407 bytes_read=4017795 bytes_retransmit=9 bytes_invalid=0 send_seq=20080 receive_seq=20080 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000084 adj=63997526 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42919 bytes_read=1760138 bytes_retransmit=9 bytes_invalid=0 send_seq=7094 receive_seq=7094 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999570 adj=47997679 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43405 bytes_read=130721 bytes_retransmit=9 bytes_invalid=0 send_seq=7081 receive_seq=7081 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97497 bytes_read=2679704 bytes_retransmit=0 bytes_invalid=0 send_seq=11640 receive_seq=11640 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998655 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.3 th2: temp=63.1 th3: temp=60.6 sysload=0.22 cputime=536.032 memavail=7394044 print_time=6917.725 buffer_time=2.187 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 101 Hz
Stats 6893.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33254497 bytes_read=5118965 bytes_retransmit=9 bytes_invalid=0 send_seq=626370 receive_seq=626370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=5958 freq=400016157 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42658 bytes_read=133360 bytes_retransmit=0 bytes_invalid=0 send_seq=7081 receive_seq=7081 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999410 adj=49997478 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213308 bytes_read=6927936 bytes_retransmit=9 bytes_invalid=0 send_seq=29825 receive_seq=29825 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997626 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=144476 bytes_read=4020843 bytes_retransmit=9 bytes_invalid=0 send_seq=20090 receive_seq=20090 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000083 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42925 bytes_read=1760372 bytes_retransmit=9 bytes_invalid=0 send_seq=7095 receive_seq=7095 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999569 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43411 bytes_read=130737 bytes_retransmit=9 bytes_invalid=0 send_seq=7082 receive_seq=7082 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97503 bytes_read=2680060 bytes_retransmit=0 bytes_invalid=0 send_seq=11641 receive_seq=11641 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998655 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.5 th2: temp=63.3 th3: temp=60.7 sysload=0.22 cputime=536.150 memavail=7394092 print_time=6918.660 buffer_time=2.121 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 102 Hz
Stats 6894.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33262332 bytes_read=5119975 bytes_retransmit=9 bytes_invalid=0 send_seq=626510 receive_seq=626510 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=6875 freq=400016122 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42664 bytes_read=133376 bytes_retransmit=0 bytes_invalid=0 send_seq=7082 receive_seq=7082 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999410 adj=49997448 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213314 bytes_read=6928036 bytes_retransmit=9 bytes_invalid=0 send_seq=29826 receive_seq=29826 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997599 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=144552 bytes_read=4023971 bytes_retransmit=9 bytes_invalid=0 send_seq=20101 receive_seq=20101 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000081 adj=63997507 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42931 bytes_read=1760681 bytes_retransmit=9 bytes_invalid=0 send_seq=7096 receive_seq=7096 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999567 adj=47997607 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43417 bytes_read=130753 bytes_retransmit=9 bytes_invalid=0 send_seq=7083 receive_seq=7083 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999428 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97509 bytes_read=2680416 bytes_retransmit=0 bytes_invalid=0 send_seq=11642 receive_seq=11642 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998639 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.1 th2: temp=63.0 th3: temp=60.5 sysload=0.22 cputime=536.285 memavail=7394092 print_time=6919.859 buffer_time=2.318 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 103 Hz
Stats 6895.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33269766 bytes_read=5120960 bytes_retransmit=9 bytes_invalid=0 send_seq=626645 receive_seq=626645 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=5612 freq=400016104 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42670 bytes_read=133392 bytes_retransmit=0 bytes_invalid=0 send_seq=7083 receive_seq=7083 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999408 adj=49997475 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213320 bytes_read=6928136 bytes_retransmit=9 bytes_invalid=0 send_seq=29827 receive_seq=29827 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997648 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=144628 bytes_read=4027028 bytes_retransmit=9 bytes_invalid=0 send_seq=20112 receive_seq=20112 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000080 adj=63997544 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42937 bytes_read=1760915 bytes_retransmit=9 bytes_invalid=0 send_seq=7097 receive_seq=7097 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999566 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43423 bytes_read=130769 bytes_retransmit=9 bytes_invalid=0 send_seq=7084 receive_seq=7084 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999440 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97515 bytes_read=2680772 bytes_retransmit=0 bytes_invalid=0 send_seq=11643 receive_seq=11643 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998665 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.4 th2: temp=63.3 th3: temp=60.6 sysload=0.20 cputime=536.405 memavail=7394092 print_time=6920.732 buffer_time=2.190 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 104 Hz
Stats 6896.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33276539 bytes_read=5121899 bytes_retransmit=9 bytes_invalid=0 send_seq=626765 receive_seq=626765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=54 upcoming_bytes=6418 freq=400016089 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=42676 bytes_read=133421 bytes_retransmit=0 bytes_invalid=0 send_seq=7084 receive_seq=7084 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999406 adj=49997476 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213326 bytes_read=6928264 bytes_retransmit=9 bytes_invalid=0 send_seq=29828 receive_seq=29828 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997732 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=144704 bytes_read=4030100 bytes_retransmit=9 bytes_invalid=0 send_seq=20123 receive_seq=20123 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000078 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42943 bytes_read=1761149 bytes_retransmit=9 bytes_invalid=0 send_seq=7098 receive_seq=7098 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999568 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43429 bytes_read=130796 bytes_retransmit=9 bytes_invalid=0 send_seq=7085 receive_seq=7085 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97521 bytes_read=2681128 bytes_retransmit=0 bytes_invalid=0 send_seq=11644 receive_seq=11644 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998680 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.4 th2: temp=63.2 th3: temp=60.6 sysload=0.20 cputime=536.526 memavail=7394092 print_time=6921.667 buffer_time=2.124 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 105 Hz
Stats 6897.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33284761 bytes_read=5122970 bytes_retransmit=9 bytes_invalid=0 send_seq=626914 receive_seq=626914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=7195 freq=400016077 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=42682 bytes_read=133437 bytes_retransmit=0 bytes_invalid=0 send_seq=7085 receive_seq=7085 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999406 adj=49997468 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213332 bytes_read=6928364 bytes_retransmit=9 bytes_invalid=0 send_seq=29829 receive_seq=29829 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997788 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=144780 bytes_read=4033188 bytes_retransmit=9 bytes_invalid=0 send_seq=20134 receive_seq=20134 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000076 adj=63997556 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42949 bytes_read=1761443 bytes_retransmit=9 bytes_invalid=0 send_seq=7099 receive_seq=7099 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999568 adj=47997697 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43435 bytes_read=130812 bytes_retransmit=9 bytes_invalid=0 send_seq=7086 receive_seq=7086 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97527 bytes_read=2681484 bytes_retransmit=0 bytes_invalid=0 send_seq=11645 receive_seq=11645 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998687 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.2 th2: temp=63.3 th3: temp=60.7 sysload=0.20 cputime=536.663 memavail=7393648 print_time=6922.868 buffer_time=2.318 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 106 Hz
Stats 6898.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33292351 bytes_read=5123989 bytes_retransmit=9 bytes_invalid=0 send_seq=627053 receive_seq=627053 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=5802 freq=400016050 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=42688 bytes_read=133453 bytes_retransmit=0 bytes_invalid=0 send_seq=7086 receive_seq=7086 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999418 adj=49997457 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213338 bytes_read=6928478 bytes_retransmit=9 bytes_invalid=0 send_seq=29830 receive_seq=29830 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997741 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=144856 bytes_read=4036245 bytes_retransmit=9 bytes_invalid=0 send_seq=20145 receive_seq=20145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000074 adj=63997545 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42955 bytes_read=1761677 bytes_retransmit=9 bytes_invalid=0 send_seq=7100 receive_seq=7100 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999566 adj=47997698 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43441 bytes_read=130828 bytes_retransmit=9 bytes_invalid=0 send_seq=7087 receive_seq=7087 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97533 bytes_read=2681840 bytes_retransmit=0 bytes_invalid=0 send_seq=11646 receive_seq=11646 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998684 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.1 th2: temp=63.2 th3: temp=60.6 sysload=0.20 cputime=536.786 memavail=7393648 print_time=6923.737 buffer_time=2.187 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 107 Hz
Stats 6899.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33299338 bytes_read=5124949 bytes_retransmit=9 bytes_invalid=0 send_seq=627180 receive_seq=627180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=6558 freq=400016037 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=42694 bytes_read=133469 bytes_retransmit=0 bytes_invalid=0 send_seq=7087 receive_seq=7087 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999416 adj=49997636 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213344 bytes_read=6928606 bytes_retransmit=9 bytes_invalid=0 send_seq=29831 receive_seq=29831 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997751 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=144932 bytes_read=4039378 bytes_retransmit=9 bytes_invalid=0 send_seq=20156 receive_seq=20156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000072 adj=63997571 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42961 bytes_read=1761926 bytes_retransmit=9 bytes_invalid=0 send_seq=7101 receive_seq=7101 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999565 adj=47997713 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43447 bytes_read=130844 bytes_retransmit=9 bytes_invalid=0 send_seq=7088 receive_seq=7088 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97539 bytes_read=2682196 bytes_retransmit=0 bytes_invalid=0 send_seq=11647 receive_seq=11647 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998707 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.3 th2: temp=63.0 th3: temp=60.6 sysload=0.20 cputime=536.908 memavail=7393648 print_time=6924.674 buffer_time=2.123 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 108 Hz
Stats 6900.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33307534 bytes_read=5125994 bytes_retransmit=9 bytes_invalid=0 send_seq=627327 receive_seq=627327 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=46 upcoming_bytes=7418 freq=400016009 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=42700 bytes_read=133485 bytes_retransmit=0 bytes_invalid=0 send_seq=7088 receive_seq=7088 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999415 adj=49997603 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213350 bytes_read=6928706 bytes_retransmit=9 bytes_invalid=0 send_seq=29832 receive_seq=29832 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997730 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=145008 bytes_read=4042448 bytes_retransmit=9 bytes_invalid=0 send_seq=20167 receive_seq=20167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997564 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42967 bytes_read=1762220 bytes_retransmit=9 bytes_invalid=0 send_seq=7102 receive_seq=7102 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999566 adj=47997707 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43453 bytes_read=130860 bytes_retransmit=9 bytes_invalid=0 send_seq=7089 receive_seq=7089 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97545 bytes_read=2682552 bytes_retransmit=0 bytes_invalid=0 send_seq=11648 receive_seq=11648 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998714 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.3 th2: temp=63.2 th3: temp=60.5 sysload=0.18 cputime=537.046 memavail=7393656 print_time=6925.873 buffer_time=2.315 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 109 Hz
Stats 6901.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33315304 bytes_read=5127028 bytes_retransmit=9 bytes_invalid=0 send_seq=627466 receive_seq=627466 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=9 upcoming_bytes=5821 freq=400015999 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42706 bytes_read=133514 bytes_retransmit=0 bytes_invalid=0 send_seq=7089 receive_seq=7089 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999413 adj=49997569 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213356 bytes_read=6928806 bytes_retransmit=9 bytes_invalid=0 send_seq=29833 receive_seq=29833 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997741 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=145084 bytes_read=4045504 bytes_retransmit=9 bytes_invalid=0 send_seq=20178 receive_seq=20178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997588 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42973 bytes_read=1762454 bytes_retransmit=9 bytes_invalid=0 send_seq=7103 receive_seq=7103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999569 adj=47997733 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43459 bytes_read=130887 bytes_retransmit=9 bytes_invalid=0 send_seq=7090 receive_seq=7090 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97551 bytes_read=2682908 bytes_retransmit=0 bytes_invalid=0 send_seq=11649 receive_seq=11649 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998754 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.0 th2: temp=63.2 th3: temp=60.7 sysload=0.18 cputime=537.169 memavail=7393656 print_time=6926.739 buffer_time=2.181 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 110 Hz
Stats 6902.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33322297 bytes_read=5127992 bytes_retransmit=9 bytes_invalid=0 send_seq=627594 receive_seq=627594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=6772 freq=400015991 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42712 bytes_read=133530 bytes_retransmit=0 bytes_invalid=0 send_seq=7090 receive_seq=7090 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999412 adj=49997550 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213362 bytes_read=6928934 bytes_retransmit=9 bytes_invalid=0 send_seq=29834 receive_seq=29834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997735 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=145160 bytes_read=4048607 bytes_retransmit=9 bytes_invalid=0 send_seq=20189 receive_seq=20189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997579 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42979 bytes_read=1762688 bytes_retransmit=9 bytes_invalid=0 send_seq=7104 receive_seq=7104 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999568 adj=47997783 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43465 bytes_read=130903 bytes_retransmit=9 bytes_invalid=0 send_seq=7091 receive_seq=7091 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97557 bytes_read=2683264 bytes_retransmit=0 bytes_invalid=0 send_seq=11650 receive_seq=11650 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998761 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.3 th2: temp=63.2 th3: temp=60.6 sysload=0.18 cputime=537.292 memavail=7393656 print_time=6927.677 buffer_time=2.119 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 111 Hz
Stats 6903.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33330575 bytes_read=5129049 bytes_retransmit=9 bytes_invalid=0 send_seq=627744 receive_seq=627744 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=15 upcoming_bytes=7608 freq=400015969 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42718 bytes_read=133546 bytes_retransmit=0 bytes_invalid=0 send_seq=7091 receive_seq=7091 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999412 adj=49997527 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213368 bytes_read=6929048 bytes_retransmit=9 bytes_invalid=0 send_seq=29835 receive_seq=29835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997840 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=145236 bytes_read=4051665 bytes_retransmit=9 bytes_invalid=0 send_seq=20200 receive_seq=20200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997567 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=42985 bytes_read=1762982 bytes_retransmit=9 bytes_invalid=0 send_seq=7105 receive_seq=7105 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999566 adj=47997755 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43471 bytes_read=130919 bytes_retransmit=9 bytes_invalid=0 send_seq=7092 receive_seq=7092 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97563 bytes_read=2683620 bytes_retransmit=0 bytes_invalid=0 send_seq=11651 receive_seq=11651 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998743 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.3 th2: temp=63.1 th3: temp=60.6 sysload=0.18 cputime=537.433 memavail=7393656 print_time=6928.872 buffer_time=2.313 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 112 Hz
Stats 6904.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33338487 bytes_read=5130108 bytes_retransmit=9 bytes_invalid=0 send_seq=627888 receive_seq=627888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=25 upcoming_bytes=5965 freq=400015969 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42724 bytes_read=133562 bytes_retransmit=0 bytes_invalid=0 send_seq=7092 receive_seq=7092 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999411 adj=49997531 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213374 bytes_read=6929148 bytes_retransmit=9 bytes_invalid=0 send_seq=29836 receive_seq=29836 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997802 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=145312 bytes_read=4054779 bytes_retransmit=9 bytes_invalid=0 send_seq=20211 receive_seq=20211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997577 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42991 bytes_read=1763231 bytes_retransmit=9 bytes_invalid=0 send_seq=7106 receive_seq=7106 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999573 adj=47997739 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43477 bytes_read=130935 bytes_retransmit=9 bytes_invalid=0 send_seq=7093 receive_seq=7093 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999459 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97569 bytes_read=2683976 bytes_retransmit=0 bytes_invalid=0 send_seq=11652 receive_seq=11652 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998729 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.1 th2: temp=63.1 th3: temp=60.5 sysload=0.18 cputime=537.558 memavail=7393656 print_time=6929.750 buffer_time=2.191 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 113 Hz
Stats 6905.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33345540 bytes_read=5131063 bytes_retransmit=9 bytes_invalid=0 send_seq=628017 receive_seq=628017 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=15 upcoming_bytes=6882 freq=400015989 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42730 bytes_read=133578 bytes_retransmit=0 bytes_invalid=0 send_seq=7093 receive_seq=7093 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999410 adj=49997506 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213380 bytes_read=6929276 bytes_retransmit=9 bytes_invalid=0 send_seq=29837 receive_seq=29837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997771 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=145388 bytes_read=4057863 bytes_retransmit=9 bytes_invalid=0 send_seq=20222 receive_seq=20222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997555 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=42997 bytes_read=1763465 bytes_retransmit=9 bytes_invalid=0 send_seq=7107 receive_seq=7107 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999572 adj=47997803 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43483 bytes_read=130951 bytes_retransmit=9 bytes_invalid=0 send_seq=7094 receive_seq=7094 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97575 bytes_read=2684332 bytes_retransmit=0 bytes_invalid=0 send_seq=11653 receive_seq=11653 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998715 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.3 th2: temp=63.1 th3: temp=60.6 sysload=0.17 cputime=537.681 memavail=7393656 print_time=6930.683 buffer_time=2.123 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 114 Hz
Stats 6906.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33353877 bytes_read=5132118 bytes_retransmit=9 bytes_invalid=0 send_seq=628166 receive_seq=628166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=29 upcoming_bytes=7895 freq=400015986 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=42736 bytes_read=133607 bytes_retransmit=0 bytes_invalid=0 send_seq=7094 receive_seq=7094 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999409 adj=49997446 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213386 bytes_read=6929376 bytes_retransmit=9 bytes_invalid=0 send_seq=29838 receive_seq=29838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997701 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=145464 bytes_read=4060919 bytes_retransmit=9 bytes_invalid=0 send_seq=20233 receive_seq=20233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997581 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43003 bytes_read=1763759 bytes_retransmit=9 bytes_invalid=0 send_seq=7108 receive_seq=7108 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999573 adj=47997751 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43489 bytes_read=130978 bytes_retransmit=9 bytes_invalid=0 send_seq=7095 receive_seq=7095 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97581 bytes_read=2684688 bytes_retransmit=0 bytes_invalid=0 send_seq=11654 receive_seq=11654 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998704 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.3 th2: temp=63.3 th3: temp=60.5 sysload=0.17 cputime=537.820 memavail=7393656 print_time=6931.883 buffer_time=2.313 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 115 Hz
Stats 6907.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33361891 bytes_read=5133198 bytes_retransmit=9 bytes_invalid=0 send_seq=628311 receive_seq=628311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=6213 freq=400015987 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=42742 bytes_read=133623 bytes_retransmit=0 bytes_invalid=0 send_seq=7095 receive_seq=7095 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999408 adj=49997428 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213392 bytes_read=6929476 bytes_retransmit=9 bytes_invalid=0 send_seq=29839 receive_seq=29839 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997743 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=145540 bytes_read=4063996 bytes_retransmit=9 bytes_invalid=0 send_seq=20244 receive_seq=20244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997550 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43009 bytes_read=1763993 bytes_retransmit=9 bytes_invalid=0 send_seq=7109 receive_seq=7109 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999571 adj=47997733 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43495 bytes_read=130994 bytes_retransmit=9 bytes_invalid=0 send_seq=7096 receive_seq=7096 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97587 bytes_read=2685044 bytes_retransmit=0 bytes_invalid=0 send_seq=11655 receive_seq=11655 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998699 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.3 th2: temp=63.3 th3: temp=60.6 sysload=0.17 cputime=537.947 memavail=7393848 print_time=6932.754 buffer_time=2.183 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 116 Hz
Stats 6908.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33368992 bytes_read=5134158 bytes_retransmit=9 bytes_invalid=0 send_seq=628441 receive_seq=628441 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=7381 freq=400015975 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=42748 bytes_read=133639 bytes_retransmit=0 bytes_invalid=0 send_seq=7096 receive_seq=7096 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999406 adj=49997415 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213398 bytes_read=6929618 bytes_retransmit=9 bytes_invalid=0 send_seq=29840 receive_seq=29840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997722 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=145616 bytes_read=4067138 bytes_retransmit=9 bytes_invalid=0 send_seq=20255 receive_seq=20255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43015 bytes_read=1764227 bytes_retransmit=9 bytes_invalid=0 send_seq=7110 receive_seq=7110 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999570 adj=47997706 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43501 bytes_read=131010 bytes_retransmit=9 bytes_invalid=0 send_seq=7097 receive_seq=7097 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97593 bytes_read=2685400 bytes_retransmit=0 bytes_invalid=0 send_seq=11656 receive_seq=11656 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998721 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.2 th2: temp=63.3 th3: temp=60.5 sysload=0.17 cputime=538.071 memavail=7393944 print_time=6933.689 buffer_time=2.118 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 117 Hz
Stats 6909.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33377564 bytes_read=5135233 bytes_retransmit=9 bytes_invalid=0 send_seq=628594 receive_seq=628594 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=8124 freq=400015966 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=42754 bytes_read=133655 bytes_retransmit=0 bytes_invalid=0 send_seq=7097 receive_seq=7097 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999405 adj=49997414 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213404 bytes_read=6929718 bytes_retransmit=9 bytes_invalid=0 send_seq=29841 receive_seq=29841 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997708 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=145692 bytes_read=4070196 bytes_retransmit=9 bytes_invalid=0 send_seq=20266 receive_seq=20266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43021 bytes_read=1764536 bytes_retransmit=9 bytes_invalid=0 send_seq=7111 receive_seq=7111 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999568 adj=47997693 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43507 bytes_read=131026 bytes_retransmit=9 bytes_invalid=0 send_seq=7098 receive_seq=7098 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97599 bytes_read=2685756 bytes_retransmit=0 bytes_invalid=0 send_seq=11657 receive_seq=11657 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998747 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.2 th2: temp=63.2 th3: temp=60.6 sysload=0.17 cputime=538.222 memavail=7388904 print_time=6934.886 buffer_time=2.314 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 118 Hz
Stats 6910.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33385923 bytes_read=5136322 bytes_retransmit=9 bytes_invalid=0 send_seq=628744 receive_seq=628744 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=6236 freq=400015961 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=42760 bytes_read=133671 bytes_retransmit=0 bytes_invalid=0 send_seq=7098 receive_seq=7098 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999404 adj=49997406 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213410 bytes_read=6929818 bytes_retransmit=9 bytes_invalid=0 send_seq=29842 receive_seq=29842 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997693 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=145768 bytes_read=4073252 bytes_retransmit=9 bytes_invalid=0 send_seq=20277 receive_seq=20277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997544 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43027 bytes_read=1764770 bytes_retransmit=9 bytes_invalid=0 send_seq=7112 receive_seq=7112 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999566 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43513 bytes_read=131042 bytes_retransmit=9 bytes_invalid=0 send_seq=7099 receive_seq=7099 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97605 bytes_read=2686112 bytes_retransmit=0 bytes_invalid=0 send_seq=11658 receive_seq=11658 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998722 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.3 th2: temp=63.3 th3: temp=60.6 sysload=0.16 cputime=538.355 memavail=7394844 print_time=6935.751 buffer_time=2.179 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 119 Hz
Stats 6911.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33392946 bytes_read=5137277 bytes_retransmit=9 bytes_invalid=0 send_seq=628873 receive_seq=628873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=46 upcoming_bytes=7272 freq=400015952 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42766 bytes_read=133700 bytes_retransmit=0 bytes_invalid=0 send_seq=7099 receive_seq=7099 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999403 adj=49997405 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213416 bytes_read=6929946 bytes_retransmit=9 bytes_invalid=0 send_seq=29843 receive_seq=29843 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997675 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=145837 bytes_read=4076317 bytes_retransmit=9 bytes_invalid=0 send_seq=20287 receive_seq=20287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997534 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43033 bytes_read=1765019 bytes_retransmit=9 bytes_invalid=0 send_seq=7113 receive_seq=7113 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999565 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43519 bytes_read=131069 bytes_retransmit=9 bytes_invalid=0 send_seq=7100 receive_seq=7100 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97611 bytes_read=2686468 bytes_retransmit=0 bytes_invalid=0 send_seq=11659 receive_seq=11659 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998717 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.3 th2: temp=63.2 th3: temp=60.6 sysload=0.16 cputime=538.481 memavail=7394844 print_time=6936.686 buffer_time=2.112 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 120 Hz
Stats 6912.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33401658 bytes_read=5138378 bytes_retransmit=9 bytes_invalid=0 send_seq=629028 receive_seq=629028 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=8148 freq=400015972 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42772 bytes_read=133716 bytes_retransmit=0 bytes_invalid=0 send_seq=7100 receive_seq=7100 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999402 adj=49997406 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213422 bytes_read=6930046 bytes_retransmit=9 bytes_invalid=0 send_seq=29844 receive_seq=29844 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997666 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=145913 bytes_read=4079390 bytes_retransmit=9 bytes_invalid=0 send_seq=20298 receive_seq=20298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43039 bytes_read=1765298 bytes_retransmit=9 bytes_invalid=0 send_seq=7114 receive_seq=7114 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43525 bytes_read=131085 bytes_retransmit=9 bytes_invalid=0 send_seq=7101 receive_seq=7101 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97617 bytes_read=2686824 bytes_retransmit=0 bytes_invalid=0 send_seq=11660 receive_seq=11660 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998710 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.5 th2: temp=63.2 th3: temp=60.5 sysload=0.16 cputime=538.623 memavail=7394844 print_time=6937.890 buffer_time=2.312 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 121 Hz
Stats 6913.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33409898 bytes_read=5139451 bytes_retransmit=9 bytes_invalid=0 send_seq=629176 receive_seq=629176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=6394 freq=400015985 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42778 bytes_read=133732 bytes_retransmit=0 bytes_invalid=0 send_seq=7101 receive_seq=7101 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999401 adj=49997365 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213428 bytes_read=6930160 bytes_retransmit=9 bytes_invalid=0 send_seq=29845 receive_seq=29845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997685 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=145989 bytes_read=4082447 bytes_retransmit=9 bytes_invalid=0 send_seq=20309 receive_seq=20309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997479 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43045 bytes_read=1765532 bytes_retransmit=9 bytes_invalid=0 send_seq=7115 receive_seq=7115 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997607 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43531 bytes_read=131101 bytes_retransmit=9 bytes_invalid=0 send_seq=7102 receive_seq=7102 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97623 bytes_read=2687180 bytes_retransmit=0 bytes_invalid=0 send_seq=11661 receive_seq=11661 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998667 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.4 th2: temp=63.2 th3: temp=60.5 sysload=0.16 cputime=538.749 memavail=7394844 print_time=6938.755 buffer_time=2.177 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 122 Hz
Stats 6914.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33416964 bytes_read=5140401 bytes_retransmit=9 bytes_invalid=0 send_seq=629304 receive_seq=629304 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=7589 freq=400015971 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42784 bytes_read=133748 bytes_retransmit=0 bytes_invalid=0 send_seq=7102 receive_seq=7102 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999400 adj=49997337 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213434 bytes_read=6930288 bytes_retransmit=9 bytes_invalid=0 send_seq=29846 receive_seq=29846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997631 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=146065 bytes_read=4085589 bytes_retransmit=9 bytes_invalid=0 send_seq=20320 receive_seq=20320 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997442 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43051 bytes_read=1765796 bytes_retransmit=9 bytes_invalid=0 send_seq=7116 receive_seq=7116 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997579 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43537 bytes_read=131117 bytes_retransmit=9 bytes_invalid=0 send_seq=7103 receive_seq=7103 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97629 bytes_read=2687536 bytes_retransmit=0 bytes_invalid=0 send_seq=11662 receive_seq=11662 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998703 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.0 th2: temp=63.1 th3: temp=60.5 sysload=0.16 cputime=538.875 memavail=7394844 print_time=6939.687 buffer_time=2.108 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 123 Hz
Stats 6915.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33425807 bytes_read=5141506 bytes_retransmit=9 bytes_invalid=0 send_seq=629463 receive_seq=629463 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=8447 freq=400015966 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42790 bytes_read=133764 bytes_retransmit=0 bytes_invalid=0 send_seq=7103 receive_seq=7103 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999398 adj=49997356 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213440 bytes_read=6930388 bytes_retransmit=9 bytes_invalid=0 send_seq=29847 receive_seq=29847 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997637 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=146141 bytes_read=4088650 bytes_retransmit=9 bytes_invalid=0 send_seq=20331 receive_seq=20331 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997465 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43057 bytes_read=1766075 bytes_retransmit=9 bytes_invalid=0 send_seq=7117 receive_seq=7117 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997596 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43543 bytes_read=131133 bytes_retransmit=9 bytes_invalid=0 send_seq=7104 receive_seq=7104 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97635 bytes_read=2687892 bytes_retransmit=0 bytes_invalid=0 send_seq=11663 receive_seq=11663 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998703 coil_temp=16.8 refs=0 mcu_temp=20.18 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.2 th2: temp=63.3 th3: temp=60.6 sysload=0.22 cputime=539.018 memavail=7394844 print_time=6940.888 buffer_time=2.308 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 124 Hz
Stats 6916.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33434280 bytes_read=5142605 bytes_retransmit=9 bytes_invalid=0 send_seq=629615 receive_seq=629615 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=17 upcoming_bytes=6556 freq=400015966 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42796 bytes_read=133793 bytes_retransmit=0 bytes_invalid=0 send_seq=7104 receive_seq=7104 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999396 adj=49997359 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213446 bytes_read=6930488 bytes_retransmit=9 bytes_invalid=0 send_seq=29848 receive_seq=29848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997634 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=146217 bytes_read=4091706 bytes_retransmit=9 bytes_invalid=0 send_seq=20342 receive_seq=20342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000072 adj=63997616 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43063 bytes_read=1766309 bytes_retransmit=9 bytes_invalid=0 send_seq=7118 receive_seq=7118 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997602 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43549 bytes_read=131160 bytes_retransmit=9 bytes_invalid=0 send_seq=7105 receive_seq=7105 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97641 bytes_read=2688248 bytes_retransmit=0 bytes_invalid=0 send_seq=11664 receive_seq=11664 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998685 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.4 th2: temp=63.2 th3: temp=60.6 sysload=0.22 cputime=539.147 memavail=7394844 print_time=6941.764 buffer_time=2.184 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Testing frequency 125 Hz
Stats 6917.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33441545 bytes_read=5143591 bytes_retransmit=9 bytes_invalid=0 send_seq=629747 receive_seq=629747 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=15 upcoming_bytes=7560 freq=400015974 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42802 bytes_read=133809 bytes_retransmit=0 bytes_invalid=0 send_seq=7105 receive_seq=7105 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999397 adj=49997342 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213452 bytes_read=6930616 bytes_retransmit=9 bytes_invalid=0 send_seq=29849 receive_seq=29849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997618 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=146293 bytes_read=4094807 bytes_retransmit=9 bytes_invalid=0 send_seq=20353 receive_seq=20353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997595 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43069 bytes_read=1766558 bytes_retransmit=9 bytes_invalid=0 send_seq=7119 receive_seq=7119 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997594 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43555 bytes_read=131176 bytes_retransmit=9 bytes_invalid=0 send_seq=7106 receive_seq=7106 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97647 bytes_read=2688604 bytes_retransmit=0 bytes_invalid=0 send_seq=11665 receive_seq=11665 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998673 coil_temp=16.8 refs=0 mcu_temp=20.16 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.4 th2: temp=62.9 th3: temp=60.6 sysload=0.22 cputime=539.275 memavail=7394352 print_time=6942.692 buffer_time=2.111 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 126 Hz
Testing frequency 127 Hz
Stats 6918.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33450278 bytes_read=5144686 bytes_retransmit=9 bytes_invalid=0 send_seq=629904 receive_seq=629904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=5368 freq=400015959 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42808 bytes_read=133825 bytes_retransmit=0 bytes_invalid=0 send_seq=7106 receive_seq=7106 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999396 adj=49997344 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213458 bytes_read=6930730 bytes_retransmit=9 bytes_invalid=0 send_seq=29850 receive_seq=29850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997588 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=146369 bytes_read=4097865 bytes_retransmit=9 bytes_invalid=0 send_seq=20364 receive_seq=20364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997560 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43075 bytes_read=1766837 bytes_retransmit=9 bytes_invalid=0 send_seq=7120 receive_seq=7120 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997579 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43561 bytes_read=131192 bytes_retransmit=9 bytes_invalid=0 send_seq=7107 receive_seq=7107 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97653 bytes_read=2688960 bytes_retransmit=0 bytes_invalid=0 send_seq=11666 receive_seq=11666 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998662 coil_temp=16.8 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.6 th2: temp=63.4 th3: temp=60.6 sysload=0.22 cputime=539.416 memavail=7394356 print_time=6943.565 buffer_time=1.984 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6919.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33458787 bytes_read=5145795 bytes_retransmit=9 bytes_invalid=0 send_seq=630058 receive_seq=630058 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=41 upcoming_bytes=6618 freq=400015944 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42814 bytes_read=133841 bytes_retransmit=0 bytes_invalid=0 send_seq=7107 receive_seq=7107 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999395 adj=49997365 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213464 bytes_read=6930830 bytes_retransmit=9 bytes_invalid=0 send_seq=29851 receive_seq=29851 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997609 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=146445 bytes_read=4100922 bytes_retransmit=9 bytes_invalid=0 send_seq=20375 receive_seq=20375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997565 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43081 bytes_read=1767086 bytes_retransmit=9 bytes_invalid=0 send_seq=7121 receive_seq=7121 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43567 bytes_read=131208 bytes_retransmit=9 bytes_invalid=0 send_seq=7108 receive_seq=7108 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97659 bytes_read=2689316 bytes_retransmit=0 bytes_invalid=0 send_seq=11667 receive_seq=11667 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998670 coil_temp=16.8 refs=0 mcu_temp=20.14 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.3 th2: temp=63.2 th3: temp=60.6 sysload=0.22 cputime=539.551 memavail=7394356 print_time=6944.766 buffer_time=2.183 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 128 Hz
Stats 6920.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33466035 bytes_read=5146765 bytes_retransmit=9 bytes_invalid=0 send_seq=630190 receive_seq=630190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=23 upcoming_bytes=7765 freq=400015924 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42820 bytes_read=133857 bytes_retransmit=0 bytes_invalid=0 send_seq=7108 receive_seq=7108 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999395 adj=49997391 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213470 bytes_read=6930958 bytes_retransmit=9 bytes_invalid=0 send_seq=29852 receive_seq=29852 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997747 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=146521 bytes_read=4104007 bytes_retransmit=9 bytes_invalid=0 send_seq=20386 receive_seq=20386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997558 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43087 bytes_read=1767350 bytes_retransmit=9 bytes_invalid=0 send_seq=7122 receive_seq=7122 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43573 bytes_read=131224 bytes_retransmit=9 bytes_invalid=0 send_seq=7109 receive_seq=7109 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97665 bytes_read=2689672 bytes_retransmit=0 bytes_invalid=0 send_seq=11668 receive_seq=11668 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998676 coil_temp=16.8 refs=0 mcu_temp=20.14 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.3 th2: temp=63.1 th3: temp=60.6 sysload=0.21 cputime=539.678 memavail=7394356 print_time=6945.697 buffer_time=2.113 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 129 Hz
Testing frequency 130 Hz
Stats 6921.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33474875 bytes_read=5147850 bytes_retransmit=9 bytes_invalid=0 send_seq=630345 receive_seq=630345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=5592 freq=400015917 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=42826 bytes_read=133886 bytes_retransmit=0 bytes_invalid=0 send_seq=7109 receive_seq=7109 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999394 adj=49997420 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213476 bytes_read=6931058 bytes_retransmit=9 bytes_invalid=0 send_seq=29853 receive_seq=29853 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997844 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=146597 bytes_read=4107122 bytes_retransmit=9 bytes_invalid=0 send_seq=20397 receive_seq=20397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997654 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43093 bytes_read=1767614 bytes_retransmit=9 bytes_invalid=0 send_seq=7123 receive_seq=7123 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43579 bytes_read=131251 bytes_retransmit=9 bytes_invalid=0 send_seq=7110 receive_seq=7110 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97671 bytes_read=2690028 bytes_retransmit=0 bytes_invalid=0 send_seq=11669 receive_seq=11669 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998688 coil_temp=16.8 refs=0 mcu_temp=20.14 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.4 th2: temp=63.2 th3: temp=60.6 sysload=0.21 cputime=539.819 memavail=7394356 print_time=6946.573 buffer_time=1.989 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 6922.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33483464 bytes_read=5148970 bytes_retransmit=9 bytes_invalid=0 send_seq=630498 receive_seq=630498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=6865 freq=400015898 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=42832 bytes_read=133902 bytes_retransmit=0 bytes_invalid=0 send_seq=7110 receive_seq=7110 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999393 adj=49997415 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213482 bytes_read=6931158 bytes_retransmit=9 bytes_invalid=0 send_seq=29854 receive_seq=29854 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997817 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=146673 bytes_read=4110195 bytes_retransmit=9 bytes_invalid=0 send_seq=20408 receive_seq=20408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997635 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43099 bytes_read=1767848 bytes_retransmit=9 bytes_invalid=0 send_seq=7124 receive_seq=7124 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43585 bytes_read=131267 bytes_retransmit=9 bytes_invalid=0 send_seq=7111 receive_seq=7111 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97677 bytes_read=2690384 bytes_retransmit=0 bytes_invalid=0 send_seq=11670 receive_seq=11670 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998688 coil_temp=16.8 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.3 th2: temp=63.3 th3: temp=60.6 sysload=0.21 cputime=539.956 memavail=7394356 print_time=6947.769 buffer_time=2.185 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 131 Hz
Stats 6923.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33490794 bytes_read=5149950 bytes_retransmit=9 bytes_invalid=0 send_seq=630632 receive_seq=630632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=52 upcoming_bytes=7975 freq=400015886 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=42838 bytes_read=133918 bytes_retransmit=0 bytes_invalid=0 send_seq=7111 receive_seq=7111 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999393 adj=49997423 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213488 bytes_read=6931300 bytes_retransmit=9 bytes_invalid=0 send_seq=29855 receive_seq=29855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997849 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=146742 bytes_read=4113257 bytes_retransmit=9 bytes_invalid=0 send_seq=20418 receive_seq=20418 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997618 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43105 bytes_read=1768112 bytes_retransmit=9 bytes_invalid=0 send_seq=7125 receive_seq=7125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43591 bytes_read=131283 bytes_retransmit=9 bytes_invalid=0 send_seq=7112 receive_seq=7112 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97683 bytes_read=2690740 bytes_retransmit=0 bytes_invalid=0 send_seq=11671 receive_seq=11671 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998689 coil_temp=16.8 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.2 th2: temp=63.1 th3: temp=60.7 sysload=0.21 cputime=540.084 memavail=7394356 print_time=6948.700 buffer_time=2.114 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 132 Hz
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Stats 6924.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33499864 bytes_read=5151061 bytes_retransmit=9 bytes_invalid=0 send_seq=630793 receive_seq=630793 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=15 upcoming_bytes=9562 freq=400015883 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=42844 bytes_read=133934 bytes_retransmit=0 bytes_invalid=0 send_seq=7112 receive_seq=7112 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999393 adj=49997444 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213494 bytes_read=6931400 bytes_retransmit=9 bytes_invalid=0 send_seq=29856 receive_seq=29856 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997818 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=146818 bytes_read=4116317 bytes_retransmit=9 bytes_invalid=0 send_seq=20429 receive_seq=20429 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997613 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43111 bytes_read=1768391 bytes_retransmit=9 bytes_invalid=0 send_seq=7126 receive_seq=7126 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997753 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43597 bytes_read=131299 bytes_retransmit=9 bytes_invalid=0 send_seq=7113 receive_seq=7113 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999471 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97689 bytes_read=2691096 bytes_retransmit=0 bytes_invalid=0 send_seq=11672 receive_seq=11672 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998691 coil_temp=16.8 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.2 th2: temp=63.2 th3: temp=60.6 sysload=0.21 cputime=540.238 memavail=7394104 print_time=6949.949 buffer_time=2.357 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6925.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33508490 bytes_read=5152165 bytes_retransmit=9 bytes_invalid=0 send_seq=630946 receive_seq=630946 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=50 upcoming_bytes=1849 freq=400015886 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=42850 bytes_read=133950 bytes_retransmit=0 bytes_invalid=0 send_seq=7113 receive_seq=7113 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999393 adj=49997435 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213500 bytes_read=6931500 bytes_retransmit=9 bytes_invalid=0 send_seq=29857 receive_seq=29857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997755 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=146894 bytes_read=4119374 bytes_retransmit=9 bytes_invalid=0 send_seq=20440 receive_seq=20440 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997575 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43117 bytes_read=1768625 bytes_retransmit=9 bytes_invalid=0 send_seq=7127 receive_seq=7127 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997718 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43603 bytes_read=131315 bytes_retransmit=9 bytes_invalid=0 send_seq=7114 receive_seq=7114 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999465 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97695 bytes_read=2691452 bytes_retransmit=0 bytes_invalid=0 send_seq=11673 receive_seq=11673 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998678 coil_temp=16.8 refs=0 mcu_temp=20.14 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.3 th2: temp=63.2 th3: temp=60.7 sysload=0.19 cputime=540.328 memavail=7394112 print_time=6949.949 buffer_time=1.356 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6926.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33510832 bytes_read=5152735 bytes_retransmit=9 bytes_invalid=0 send_seq=630998 receive_seq=630998 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015892 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42856 bytes_read=133979 bytes_retransmit=0 bytes_invalid=0 send_seq=7114 receive_seq=7114 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999393 adj=49997429 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213506 bytes_read=6931628 bytes_retransmit=9 bytes_invalid=0 send_seq=29858 receive_seq=29858 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997722 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=146970 bytes_read=4122519 bytes_retransmit=9 bytes_invalid=0 send_seq=20451 receive_seq=20451 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997558 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43123 bytes_read=1768904 bytes_retransmit=9 bytes_invalid=0 send_seq=7128 receive_seq=7128 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997706 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43609 bytes_read=131342 bytes_retransmit=9 bytes_invalid=0 send_seq=7115 receive_seq=7115 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999462 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97701 bytes_read=2691808 bytes_retransmit=0 bytes_invalid=0 send_seq=11674 receive_seq=11674 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998668 coil_temp=16.8 refs=0 mcu_temp=20.14 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.4 th2: temp=63.2 th3: temp=60.6 sysload=0.19 cputime=540.405 memavail=7388608 print_time=6949.949 buffer_time=0.354 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
LIS2DW finished 'toolboard_t1' measurements
Resonances data written to /tmp/resonances_x_125.000_250.000_20.000_t1_mirror.csv file
Probing point (125.000, 250.000, 20.000)
Stats 6927.9: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33511238 bytes_read=5153186 bytes_retransmit=9 bytes_invalid=0 send_seq=631023 receive_seq=631023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015879 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42862 bytes_read=133995 bytes_retransmit=0 bytes_invalid=0 send_seq=7115 receive_seq=7115 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999391 adj=49997420 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213512 bytes_read=6931728 bytes_retransmit=9 bytes_invalid=0 send_seq=29859 receive_seq=29859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997689 toolboard_t1: mcu_awake=0.300 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=147059 bytes_read=4123956 bytes_retransmit=9 bytes_invalid=0 send_seq=20462 receive_seq=20462 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43129 bytes_read=1769153 bytes_retransmit=9 bytes_invalid=0 send_seq=7129 receive_seq=7129 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43615 bytes_read=131358 bytes_retransmit=9 bytes_invalid=0 send_seq=7116 receive_seq=7116 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999462 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97707 bytes_read=2692164 bytes_retransmit=0 bytes_invalid=0 send_seq=11675 receive_seq=11675 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998660 coil_temp=16.8 refs=0 mcu_temp=20.14 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.4 th2: temp=63.1 th3: temp=60.7 sysload=0.19 cputime=540.523 memavail=7395460 print_time=6950.932 buffer_time=0.337 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
lis2dw_dev_id: 44
LIS2DW starting 'toolboard_t1' measurements
toolhead: max_velocity: 600.000000
max_accel: 8379.841000
minimum_cruise_ratio: 0.000000
square_corner_velocity: 5.000000
Disabled [input_shaper] for resonance testing
Testing frequency 10 Hz
Testing frequency 11 Hz
Testing frequency 12 Hz
Stats 6928.9: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33520500 bytes_read=5154380 bytes_retransmit=9 bytes_invalid=0 send_seq=631194 receive_seq=631194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=432 freq=400015859 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42868 bytes_read=134011 bytes_retransmit=0 bytes_invalid=0 send_seq=7116 receive_seq=7116 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999390 adj=49997428 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213518 bytes_read=6931842 bytes_retransmit=9 bytes_invalid=0 send_seq=29860 receive_seq=29860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997693 toolboard_t1: mcu_awake=0.300 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=147214 bytes_read=4126020 bytes_retransmit=9 bytes_invalid=0 send_seq=20480 receive_seq=20480 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997543 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43135 bytes_read=1769387 bytes_retransmit=9 bytes_invalid=0 send_seq=7130 receive_seq=7130 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997748 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43621 bytes_read=131374 bytes_retransmit=9 bytes_invalid=0 send_seq=7117 receive_seq=7117 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999470 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97713 bytes_read=2692520 bytes_retransmit=0 bytes_invalid=0 send_seq=11676 receive_seq=11676 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998690 coil_temp=16.8 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=56.3 th1: temp=56.3 th2: temp=63.2 th3: temp=60.6 sysload=0.19 cputime=540.720 memavail=7395460 print_time=6954.096 buffer_time=2.499 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6929.9: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33523793 bytes_read=5155040 bytes_retransmit=9 bytes_invalid=0 send_seq=631264 receive_seq=631264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=0 freq=400015842 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42874 bytes_read=134027 bytes_retransmit=0 bytes_invalid=0 send_seq=7117 receive_seq=7117 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999392 adj=49997426 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213524 bytes_read=6931970 bytes_retransmit=9 bytes_invalid=0 send_seq=29861 receive_seq=29861 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997714 toolboard_t1: mcu_awake=0.300 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=147290 bytes_read=4129048 bytes_retransmit=9 bytes_invalid=0 send_seq=20491 receive_seq=20491 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997586 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43141 bytes_read=1769681 bytes_retransmit=9 bytes_invalid=0 send_seq=7131 receive_seq=7131 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999565 adj=47997723 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43627 bytes_read=131390 bytes_retransmit=9 bytes_invalid=0 send_seq=7118 receive_seq=7118 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999456 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97719 bytes_read=2692876 bytes_retransmit=0 bytes_invalid=0 send_seq=11677 receive_seq=11677 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998702 coil_temp=16.8 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.3 th2: temp=63.2 th3: temp=60.5 sysload=0.19 cputime=540.796 memavail=7395460 print_time=6954.689 buffer_time=2.092 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 13 Hz
Testing frequency 14 Hz
Stats 6930.9: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33528284 bytes_read=5155790 bytes_retransmit=9 bytes_invalid=0 send_seq=631352 receive_seq=631352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=27 upcoming_bytes=1137 freq=400015833 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42880 bytes_read=134043 bytes_retransmit=0 bytes_invalid=0 send_seq=7118 receive_seq=7118 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999391 adj=49997470 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213530 bytes_read=6932070 bytes_retransmit=9 bytes_invalid=0 send_seq=29862 receive_seq=29862 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997749 toolboard_t1: mcu_awake=0.300 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=147366 bytes_read=4132082 bytes_retransmit=9 bytes_invalid=0 send_seq=20502 receive_seq=20502 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997624 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43147 bytes_read=1769930 bytes_retransmit=9 bytes_invalid=0 send_seq=7132 receive_seq=7132 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997781 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43633 bytes_read=131406 bytes_retransmit=9 bytes_invalid=0 send_seq=7119 receive_seq=7119 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97725 bytes_read=2693232 bytes_retransmit=0 bytes_invalid=0 send_seq=11678 receive_seq=11678 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998722 coil_temp=16.8 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.4 th2: temp=63.2 th3: temp=60.4 sysload=0.17 cputime=540.888 memavail=7395460 print_time=6955.961 buffer_time=2.364 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 15 Hz
Stats 6931.9: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33533094 bytes_read=5156604 bytes_retransmit=9 bytes_invalid=0 send_seq=631447 receive_seq=631447 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=376 freq=400015956 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42886 bytes_read=134072 bytes_retransmit=0 bytes_invalid=0 send_seq=7119 receive_seq=7119 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999391 adj=49997463 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213536 bytes_read=6932170 bytes_retransmit=9 bytes_invalid=0 send_seq=29863 receive_seq=29863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997728 toolboard_t1: mcu_awake=0.300 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=147442 bytes_read=4135142 bytes_retransmit=9 bytes_invalid=0 send_seq=20513 receive_seq=20513 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997602 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43153 bytes_read=1770164 bytes_retransmit=9 bytes_invalid=0 send_seq=7133 receive_seq=7133 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997747 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43639 bytes_read=131433 bytes_retransmit=9 bytes_invalid=0 send_seq=7120 receive_seq=7120 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999467 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97731 bytes_read=2693588 bytes_retransmit=0 bytes_invalid=0 send_seq=11679 receive_seq=11679 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998710 coil_temp=16.8 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.3 th2: temp=63.1 th3: temp=60.5 sysload=0.17 cputime=540.977 memavail=7395460 print_time=6956.816 buffer_time=2.218 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 16 Hz
Stats 6932.9: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=33537156 bytes_read=5157325 bytes_retransmit=9 bytes_invalid=0 send_seq=631526 receive_seq=631526 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=1464 freq=400016044 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42892 bytes_read=134088 bytes_retransmit=0 bytes_invalid=0 send_seq=7120 receive_seq=7120 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999390 adj=49997267 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213542 bytes_read=6932298 bytes_retransmit=9 bytes_invalid=0 send_seq=29864 receive_seq=29864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997472 toolboard_t1: mcu_awake=0.281 mcu_task_avg=0.000117 mcu_task_stddev=0.000069 bytes_write=147518 bytes_read=4138243 bytes_retransmit=9 bytes_invalid=0 send_seq=20524 receive_seq=20524 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000068 adj=63997374 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43159 bytes_read=1770443 bytes_retransmit=9 bytes_invalid=0 send_seq=7134 receive_seq=7134 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999563 adj=47997546 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43645 bytes_read=131449 bytes_retransmit=9 bytes_invalid=0 send_seq=7121 receive_seq=7121 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999420 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97737 bytes_read=2693944 bytes_retransmit=0 bytes_invalid=0 send_seq=11680 receive_seq=11680 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998585 coil_temp=16.8 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.3 th2: temp=63.0 th3: temp=60.4 sysload=0.17 cputime=541.068 memavail=7395460 print_time=6957.781 buffer_time=2.183 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6933.9: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=33542346 bytes_read=5158130 bytes_retransmit=9 bytes_invalid=0 send_seq=631625 receive_seq=631625 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=504 freq=400016025 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42898 bytes_read=134104 bytes_retransmit=0 bytes_invalid=0 send_seq=7121 receive_seq=7121 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999390 adj=49997144 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213548 bytes_read=6932398 bytes_retransmit=9 bytes_invalid=0 send_seq=29865 receive_seq=29865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000215 adj=63997313 toolboard_t1: mcu_awake=0.281 mcu_task_avg=0.000117 mcu_task_stddev=0.000069 bytes_write=147594 bytes_read=4141299 bytes_retransmit=9 bytes_invalid=0 send_seq=20535 receive_seq=20535 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997250 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43165 bytes_read=1770692 bytes_retransmit=9 bytes_invalid=0 send_seq=7135 receive_seq=7135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997430 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43651 bytes_read=131465 bytes_retransmit=9 bytes_invalid=0 send_seq=7122 receive_seq=7122 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999388 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97743 bytes_read=2694300 bytes_retransmit=0 bytes_invalid=0 send_seq=11681 receive_seq=11681 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998510 coil_temp=16.8 refs=0 mcu_temp=20.16 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.4 th2: temp=62.9 th3: temp=60.3 sysload=0.17 cputime=541.161 memavail=7395460 print_time=6958.662 buffer_time=2.062 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 17 Hz
Testing frequency 18 Hz
Stats 6934.9: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=33547411 bytes_read=5158972 bytes_retransmit=9 bytes_invalid=0 send_seq=631724 receive_seq=631724 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=2073 freq=400015987 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42910 bytes_read=134136 bytes_retransmit=0 bytes_invalid=0 send_seq=7123 receive_seq=7123 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999389 adj=49997195 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213560 bytes_read=6932528 bytes_retransmit=9 bytes_invalid=0 send_seq=29867 receive_seq=29867 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997372 toolboard_t1: mcu_awake=0.281 mcu_task_avg=0.000117 mcu_task_stddev=0.000069 bytes_write=147669 bytes_read=4144407 bytes_retransmit=9 bytes_invalid=0 send_seq=20546 receive_seq=20546 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997325 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43177 bytes_read=1770957 bytes_retransmit=9 bytes_invalid=0 send_seq=7137 receive_seq=7137 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997497 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43663 bytes_read=131497 bytes_retransmit=9 bytes_invalid=0 send_seq=7124 receive_seq=7124 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999399 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97755 bytes_read=2694672 bytes_retransmit=0 bytes_invalid=0 send_seq=11683 receive_seq=11683 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998600 coil_temp=16.8 refs=0 mcu_temp=20.16 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.4 th2: temp=62.9 th3: temp=60.3 sysload=0.17 cputime=541.265 memavail=7395460 print_time=6959.930 buffer_time=2.327 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 19 Hz
Stats 6935.9: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=33552283 bytes_read=5159755 bytes_retransmit=9 bytes_invalid=0 send_seq=631819 receive_seq=631819 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=2556 freq=400015973 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42916 bytes_read=134152 bytes_retransmit=0 bytes_invalid=0 send_seq=7124 receive_seq=7124 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999389 adj=49997302 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213566 bytes_read=6932656 bytes_retransmit=9 bytes_invalid=0 send_seq=29868 receive_seq=29868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997515 toolboard_t1: mcu_awake=0.281 mcu_task_avg=0.000117 mcu_task_stddev=0.000069 bytes_write=147745 bytes_read=4147491 bytes_retransmit=9 bytes_invalid=0 send_seq=20557 receive_seq=20557 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997485 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43183 bytes_read=1771251 bytes_retransmit=9 bytes_invalid=0 send_seq=7138 receive_seq=7138 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997566 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43669 bytes_read=131513 bytes_retransmit=9 bytes_invalid=0 send_seq=7125 receive_seq=7125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999423 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97761 bytes_read=2695028 bytes_retransmit=0 bytes_invalid=0 send_seq=11684 receive_seq=11684 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998655 coil_temp=16.8 refs=0 mcu_temp=20.16 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.3 th2: temp=62.7 th3: temp=60.2 sysload=0.16 cputime=541.356 memavail=7396720 print_time=6960.751 buffer_time=2.146 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 20 Hz
Stats 6936.9: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000004 mcu_task_stddev=0.000004 bytes_write=33558161 bytes_read=5160610 bytes_retransmit=9 bytes_invalid=0 send_seq=631928 receive_seq=631928 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=1867 freq=400015960 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42922 bytes_read=134181 bytes_retransmit=0 bytes_invalid=0 send_seq=7125 receive_seq=7125 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999388 adj=49997330 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213572 bytes_read=6932756 bytes_retransmit=9 bytes_invalid=0 send_seq=29869 receive_seq=29869 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997550 toolboard_t1: mcu_awake=0.281 mcu_task_avg=0.000117 mcu_task_stddev=0.000069 bytes_write=147821 bytes_read=4150549 bytes_retransmit=9 bytes_invalid=0 send_seq=20568 receive_seq=20568 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997497 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43189 bytes_read=1771485 bytes_retransmit=9 bytes_invalid=0 send_seq=7139 receive_seq=7139 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997583 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43675 bytes_read=131540 bytes_retransmit=9 bytes_invalid=0 send_seq=7126 receive_seq=7126 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97767 bytes_read=2695375 bytes_retransmit=0 bytes_invalid=0 send_seq=11685 receive_seq=11685 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998694 coil_temp=16.8 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.5 th2: temp=62.7 th3: temp=60.1 sysload=0.16 cputime=541.456 memavail=7396720 print_time=6961.736 buffer_time=2.131 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6937.9: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33564126 bytes_read=5161525 bytes_retransmit=9 bytes_invalid=0 send_seq=632040 receive_seq=632040 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=1804 freq=400015963 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42928 bytes_read=134197 bytes_retransmit=0 bytes_invalid=0 send_seq=7126 receive_seq=7126 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999388 adj=49997358 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213578 bytes_read=6932856 bytes_retransmit=9 bytes_invalid=0 send_seq=29870 receive_seq=29870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997581 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=147897 bytes_read=4153623 bytes_retransmit=9 bytes_invalid=0 send_seq=20579 receive_seq=20579 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43195 bytes_read=1771719 bytes_retransmit=9 bytes_invalid=0 send_seq=7140 receive_seq=7140 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997600 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43681 bytes_read=131556 bytes_retransmit=9 bytes_invalid=0 send_seq=7127 receive_seq=7127 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97773 bytes_read=2695720 bytes_retransmit=0 bytes_invalid=0 send_seq=11686 receive_seq=11686 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998690 coil_temp=16.8 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.5 th2: temp=62.8 th3: temp=60.2 sysload=0.16 cputime=541.551 memavail=7395028 print_time=6962.608 buffer_time=2.002 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 21 Hz
Testing frequency 22 Hz
Stats 6938.9: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33569316 bytes_read=5162335 bytes_retransmit=9 bytes_invalid=0 send_seq=632140 receive_seq=632140 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=33 upcoming_bytes=3784 freq=400015942 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42934 bytes_read=134213 bytes_retransmit=0 bytes_invalid=0 send_seq=7127 receive_seq=7127 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999387 adj=49997351 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213584 bytes_read=6932984 bytes_retransmit=9 bytes_invalid=0 send_seq=29871 receive_seq=29871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997587 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=147973 bytes_read=4156708 bytes_retransmit=9 bytes_invalid=0 send_seq=20590 receive_seq=20590 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997482 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43201 bytes_read=1772013 bytes_retransmit=9 bytes_invalid=0 send_seq=7141 receive_seq=7141 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997587 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43687 bytes_read=131572 bytes_retransmit=9 bytes_invalid=0 send_seq=7128 receive_seq=7128 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97779 bytes_read=2696064 bytes_retransmit=0 bytes_invalid=0 send_seq=11687 receive_seq=11687 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998671 coil_temp=16.8 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.1 th2: temp=62.6 th3: temp=60.1 sysload=0.16 cputime=541.657 memavail=7394816 print_time=6963.831 buffer_time=2.225 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 23 Hz
Stats 6939.9: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33575664 bytes_read=5163230 bytes_retransmit=9 bytes_invalid=0 send_seq=632257 receive_seq=632257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=36 upcoming_bytes=2809 freq=400015921 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42940 bytes_read=134229 bytes_retransmit=0 bytes_invalid=0 send_seq=7128 receive_seq=7128 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999388 adj=49997388 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213590 bytes_read=6933098 bytes_retransmit=9 bytes_invalid=0 send_seq=29872 receive_seq=29872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997646 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=148049 bytes_read=4159765 bytes_retransmit=9 bytes_invalid=0 send_seq=20601 receive_seq=20601 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997513 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43207 bytes_read=1772262 bytes_retransmit=9 bytes_invalid=0 send_seq=7142 receive_seq=7142 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997625 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43693 bytes_read=131588 bytes_retransmit=9 bytes_invalid=0 send_seq=7129 receive_seq=7129 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97785 bytes_read=2696409 bytes_retransmit=0 bytes_invalid=0 send_seq=11688 receive_seq=11688 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998678 coil_temp=16.8 refs=0 mcu_temp=20.16 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.3 th2: temp=62.5 th3: temp=60.0 sysload=0.16 cputime=541.755 memavail=7394816 print_time=6964.751 buffer_time=2.144 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6940.9: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33581923 bytes_read=5164139 bytes_retransmit=9 bytes_invalid=0 send_seq=632372 receive_seq=632371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=2980 freq=400015904 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42946 bytes_read=134245 bytes_retransmit=0 bytes_invalid=0 send_seq=7129 receive_seq=7129 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999387 adj=49997432 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213596 bytes_read=6933198 bytes_retransmit=9 bytes_invalid=0 send_seq=29873 receive_seq=29873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997703 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=148125 bytes_read=4162880 bytes_retransmit=9 bytes_invalid=0 send_seq=20612 receive_seq=20612 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43213 bytes_read=1772496 bytes_retransmit=9 bytes_invalid=0 send_seq=7143 receive_seq=7143 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43699 bytes_read=131604 bytes_retransmit=9 bytes_invalid=0 send_seq=7130 receive_seq=7130 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97791 bytes_read=2696754 bytes_retransmit=0 bytes_invalid=0 send_seq=11689 receive_seq=11689 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998690 coil_temp=16.8 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.3 th2: temp=62.4 th3: temp=60.1 sysload=0.15 cputime=541.851 memavail=7394816 print_time=6965.636 buffer_time=2.029 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 24 Hz
Testing frequency 25 Hz
Stats 6941.9: gcodein=0  mcu: mcu_awake=0.005 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33587718 bytes_read=5164974 bytes_retransmit=9 bytes_invalid=0 send_seq=632476 receive_seq=632476 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=2972 freq=400015885 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42952 bytes_read=134274 bytes_retransmit=0 bytes_invalid=0 send_seq=7130 receive_seq=7130 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999388 adj=49997440 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213602 bytes_read=6933326 bytes_retransmit=9 bytes_invalid=0 send_seq=29874 receive_seq=29874 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997730 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=148201 bytes_read=4165964 bytes_retransmit=9 bytes_invalid=0 send_seq=20623 receive_seq=20623 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997552 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43219 bytes_read=1772790 bytes_retransmit=9 bytes_invalid=0 send_seq=7144 receive_seq=7144 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997664 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43705 bytes_read=131631 bytes_retransmit=9 bytes_invalid=0 send_seq=7131 receive_seq=7131 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97797 bytes_read=2697099 bytes_retransmit=0 bytes_invalid=0 send_seq=11690 receive_seq=11690 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998725 coil_temp=16.8 refs=0 mcu_temp=20.14 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.4 th2: temp=62.4 th3: temp=60.0 sysload=0.15 cputime=541.952 memavail=7394816 print_time=6966.601 buffer_time=1.993 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 26 Hz
Stats 6942.9: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=33594608 bytes_read=5165935 bytes_retransmit=9 bytes_invalid=0 send_seq=632603 receive_seq=632603 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=4524 freq=400015886 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42958 bytes_read=134290 bytes_retransmit=0 bytes_invalid=0 send_seq=7131 receive_seq=7131 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999388 adj=49997475 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213608 bytes_read=6933426 bytes_retransmit=9 bytes_invalid=0 send_seq=29875 receive_seq=29875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997746 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=148277 bytes_read=4169038 bytes_retransmit=9 bytes_invalid=0 send_seq=20634 receive_seq=20634 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997570 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43225 bytes_read=1773024 bytes_retransmit=9 bytes_invalid=0 send_seq=7145 receive_seq=7145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997689 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43711 bytes_read=131647 bytes_retransmit=9 bytes_invalid=0 send_seq=7132 receive_seq=7132 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97803 bytes_read=2697444 bytes_retransmit=0 bytes_invalid=0 send_seq=11691 receive_seq=11691 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998721 coil_temp=16.8 refs=0 mcu_temp=20.14 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.4 th2: temp=62.5 th3: temp=59.9 sysload=0.15 cputime=542.060 memavail=7394836 print_time=6967.828 buffer_time=2.219 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6943.9: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=33601554 bytes_read=5166909 bytes_retransmit=9 bytes_invalid=0 send_seq=632730 receive_seq=632730 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=3752 freq=400015891 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42964 bytes_read=134306 bytes_retransmit=0 bytes_invalid=0 send_seq=7132 receive_seq=7132 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999389 adj=49997452 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213614 bytes_read=6933526 bytes_retransmit=9 bytes_invalid=0 send_seq=29876 receive_seq=29876 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997710 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=148353 bytes_read=4172096 bytes_retransmit=9 bytes_invalid=0 send_seq=20645 receive_seq=20645 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997546 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43231 bytes_read=1773258 bytes_retransmit=9 bytes_invalid=0 send_seq=7146 receive_seq=7146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43717 bytes_read=131663 bytes_retransmit=9 bytes_invalid=0 send_seq=7133 receive_seq=7133 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97809 bytes_read=2697789 bytes_retransmit=0 bytes_invalid=0 send_seq=11692 receive_seq=11692 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998692 coil_temp=16.8 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.3 th2: temp=62.3 th3: temp=59.9 sysload=0.15 cputime=542.161 memavail=7393580 print_time=6968.686 buffer_time=2.077 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 27 Hz
Stats 6944.9: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=33607588 bytes_read=5167774 bytes_retransmit=9 bytes_invalid=0 send_seq=632841 receive_seq=632841 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=4564 freq=400016111 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42970 bytes_read=134322 bytes_retransmit=0 bytes_invalid=0 send_seq=7133 receive_seq=7133 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999389 adj=49997456 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213620 bytes_read=6933668 bytes_retransmit=9 bytes_invalid=0 send_seq=29877 receive_seq=29877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997706 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=148429 bytes_read=4175180 bytes_retransmit=9 bytes_invalid=0 send_seq=20656 receive_seq=20656 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997518 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43237 bytes_read=1773567 bytes_retransmit=9 bytes_invalid=0 send_seq=7147 receive_seq=7147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43723 bytes_read=131679 bytes_retransmit=9 bytes_invalid=0 send_seq=7134 receive_seq=7134 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97815 bytes_read=2698139 bytes_retransmit=0 bytes_invalid=0 send_seq=11693 receive_seq=11693 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998673 coil_temp=16.8 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.4 th2: temp=62.8 th3: temp=59.8 sysload=0.15 cputime=542.270 memavail=7395940 print_time=6969.662 buffer_time=2.053 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 28 Hz
Testing frequency 29 Hz
Stats 6945.9: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=33614948 bytes_read=5168727 bytes_retransmit=9 bytes_invalid=0 send_seq=632970 receive_seq=632970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=5328 freq=400016106 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42976 bytes_read=134338 bytes_retransmit=0 bytes_invalid=0 send_seq=7134 receive_seq=7134 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999388 adj=49997094 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213626 bytes_read=6933768 bytes_retransmit=9 bytes_invalid=0 send_seq=29878 receive_seq=29878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997243 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=148505 bytes_read=4178238 bytes_retransmit=9 bytes_invalid=0 send_seq=20667 receive_seq=20667 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997069 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43243 bytes_read=1773801 bytes_retransmit=9 bytes_invalid=0 send_seq=7148 receive_seq=7148 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997308 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43729 bytes_read=131695 bytes_retransmit=9 bytes_invalid=0 send_seq=7135 receive_seq=7135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999359 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97821 bytes_read=2698495 bytes_retransmit=0 bytes_invalid=0 send_seq=11694 receive_seq=11694 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998446 coil_temp=16.8 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.3 th2: temp=62.3 th3: temp=59.7 sysload=0.13 cputime=542.383 memavail=7395692 print_time=6970.837 buffer_time=2.227 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 30 Hz
Stats 6946.9: gcodein=0  mcu: mcu_awake=0.006 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=33622194 bytes_read=5169719 bytes_retransmit=9 bytes_invalid=0 send_seq=633101 receive_seq=633101 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=4560 freq=400016081 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42982 bytes_read=134367 bytes_retransmit=0 bytes_invalid=0 send_seq=7135 receive_seq=7135 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999387 adj=49997174 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213632 bytes_read=6933868 bytes_retransmit=9 bytes_invalid=0 send_seq=29879 receive_seq=29879 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997362 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=148581 bytes_read=4181294 bytes_retransmit=9 bytes_invalid=0 send_seq=20678 receive_seq=20678 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997186 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43249 bytes_read=1774035 bytes_retransmit=9 bytes_invalid=0 send_seq=7149 receive_seq=7149 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997428 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43735 bytes_read=131722 bytes_retransmit=9 bytes_invalid=0 send_seq=7136 receive_seq=7136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999406 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97827 bytes_read=2698851 bytes_retransmit=0 bytes_invalid=0 send_seq=11695 receive_seq=11695 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998508 coil_temp=16.8 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.4 th2: temp=62.4 th3: temp=59.7 sysload=0.13 cputime=542.486 memavail=7395468 print_time=6971.718 buffer_time=2.107 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 6947.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=33628551 bytes_read=5170635 bytes_retransmit=9 bytes_invalid=0 send_seq=633219 receive_seq=633219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=5517 freq=400016067 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42988 bytes_read=134383 bytes_retransmit=0 bytes_invalid=0 send_seq=7136 receive_seq=7136 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999386 adj=49997222 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213638 bytes_read=6933996 bytes_retransmit=9 bytes_invalid=0 send_seq=29880 receive_seq=29880 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997426 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=148650 bytes_read=4184432 bytes_retransmit=9 bytes_invalid=0 send_seq=20688 receive_seq=20688 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997254 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43255 bytes_read=1774329 bytes_retransmit=9 bytes_invalid=0 send_seq=7150 receive_seq=7150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997494 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43741 bytes_read=131738 bytes_retransmit=9 bytes_invalid=0 send_seq=7137 receive_seq=7137 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999422 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97833 bytes_read=2699207 bytes_retransmit=0 bytes_invalid=0 send_seq=11696 receive_seq=11696 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998542 coil_temp=16.8 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.4 th2: temp=62.2 th3: temp=59.6 sysload=0.13 cputime=542.587 memavail=7393956 print_time=6972.679 buffer_time=2.067 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 31 Hz
Testing frequency 32 Hz
Stats 6948.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=33636396 bytes_read=5171650 bytes_retransmit=9 bytes_invalid=0 send_seq=633360 receive_seq=633360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=6332 freq=400016054 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=42994 bytes_read=134399 bytes_retransmit=0 bytes_invalid=0 send_seq=7137 receive_seq=7137 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999385 adj=49997252 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213644 bytes_read=6934096 bytes_retransmit=9 bytes_invalid=0 send_seq=29881 receive_seq=29881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997494 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=148726 bytes_read=4187488 bytes_retransmit=9 bytes_invalid=0 send_seq=20699 receive_seq=20699 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997319 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43261 bytes_read=1774563 bytes_retransmit=9 bytes_invalid=0 send_seq=7151 receive_seq=7151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997542 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43747 bytes_read=131754 bytes_retransmit=9 bytes_invalid=0 send_seq=7138 receive_seq=7138 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97839 bytes_read=2699563 bytes_retransmit=0 bytes_invalid=0 send_seq=11697 receive_seq=11697 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998569 coil_temp=16.8 refs=0 mcu_temp=20.15 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.5 th2: temp=62.1 th3: temp=59.5 sysload=0.13 cputime=542.698 memavail=7393956 print_time=6973.860 buffer_time=2.248 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 33 Hz
Stats 6949.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=33643997 bytes_read=5172689 bytes_retransmit=9 bytes_invalid=0 send_seq=633500 receive_seq=633500 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=5324 freq=400016054 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43000 bytes_read=134415 bytes_retransmit=0 bytes_invalid=0 send_seq=7138 receive_seq=7138 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999385 adj=49997302 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213650 bytes_read=6934210 bytes_retransmit=9 bytes_invalid=0 send_seq=29882 receive_seq=29882 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997564 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=148802 bytes_read=4190544 bytes_retransmit=9 bytes_invalid=0 send_seq=20710 receive_seq=20710 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997389 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43267 bytes_read=1774812 bytes_retransmit=9 bytes_invalid=0 send_seq=7152 receive_seq=7152 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997590 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43753 bytes_read=131770 bytes_retransmit=9 bytes_invalid=0 send_seq=7139 receive_seq=7139 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97845 bytes_read=2699919 bytes_retransmit=0 bytes_invalid=0 send_seq=11698 receive_seq=11698 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998603 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.4 th2: temp=62.1 th3: temp=59.6 sysload=0.13 cputime=542.805 memavail=7393956 print_time=6974.759 buffer_time=2.146 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6950.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=33650741 bytes_read=5173609 bytes_retransmit=9 bytes_invalid=0 send_seq=633622 receive_seq=633622 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=6460 freq=400016040 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43006 bytes_read=134431 bytes_retransmit=0 bytes_invalid=0 send_seq=7139 receive_seq=7139 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999385 adj=49997306 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213656 bytes_read=6934338 bytes_retransmit=9 bytes_invalid=0 send_seq=29883 receive_seq=29883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997563 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=148878 bytes_read=4193630 bytes_retransmit=9 bytes_invalid=0 send_seq=20721 receive_seq=20721 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997390 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43273 bytes_read=1775106 bytes_retransmit=9 bytes_invalid=0 send_seq=7153 receive_seq=7153 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997611 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43759 bytes_read=131786 bytes_retransmit=9 bytes_invalid=0 send_seq=7140 receive_seq=7140 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97851 bytes_read=2700275 bytes_retransmit=0 bytes_invalid=0 send_seq=11699 receive_seq=11699 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998600 coil_temp=16.8 refs=0 mcu_temp=20.16 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.5 th2: temp=62.1 th3: temp=59.6 sysload=0.20 cputime=542.910 memavail=7393956 print_time=6975.700 buffer_time=2.085 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 34 Hz
Testing frequency 35 Hz
Stats 6951.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000005 bytes_write=33658880 bytes_read=5174644 bytes_retransmit=9 bytes_invalid=0 send_seq=633767 receive_seq=633767 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=7872 freq=400016044 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43012 bytes_read=134460 bytes_retransmit=0 bytes_invalid=0 send_seq=7140 receive_seq=7140 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999385 adj=49997339 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213662 bytes_read=6934438 bytes_retransmit=9 bytes_invalid=0 send_seq=29884 receive_seq=29884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997595 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=148954 bytes_read=4196686 bytes_retransmit=9 bytes_invalid=0 send_seq=20732 receive_seq=20732 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997422 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43279 bytes_read=1775340 bytes_retransmit=9 bytes_invalid=0 send_seq=7154 receive_seq=7154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43765 bytes_read=131813 bytes_retransmit=9 bytes_invalid=0 send_seq=7141 receive_seq=7141 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97857 bytes_read=2700631 bytes_retransmit=0 bytes_invalid=0 send_seq=11700 receive_seq=11700 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998625 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=57.2 th1: temp=56.1 th2: temp=62.2 th3: temp=59.6 sysload=0.20 cputime=543.030 memavail=7393956 print_time=6976.908 buffer_time=2.293 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 36 Hz
Stats 6952.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33666989 bytes_read=5175729 bytes_retransmit=9 bytes_invalid=0 send_seq=633913 receive_seq=633913 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=6363 freq=400016034 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43018 bytes_read=134476 bytes_retransmit=0 bytes_invalid=0 send_seq=7141 receive_seq=7141 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999384 adj=49997346 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213668 bytes_read=6934538 bytes_retransmit=9 bytes_invalid=0 send_seq=29885 receive_seq=29885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997595 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=149030 bytes_read=4199760 bytes_retransmit=9 bytes_invalid=0 send_seq=20743 receive_seq=20743 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997430 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43285 bytes_read=1775574 bytes_retransmit=9 bytes_invalid=0 send_seq=7155 receive_seq=7155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43771 bytes_read=131829 bytes_retransmit=9 bytes_invalid=0 send_seq=7142 receive_seq=7142 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97863 bytes_read=2700987 bytes_retransmit=0 bytes_invalid=0 send_seq=11701 receive_seq=11701 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998629 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=57.2 th1: temp=56.1 th2: temp=62.0 th3: temp=59.5 sysload=0.20 cputime=543.143 memavail=7393956 print_time=6977.786 buffer_time=2.170 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 6953.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33674082 bytes_read=5176689 bytes_retransmit=9 bytes_invalid=0 send_seq=634043 receive_seq=634043 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=7783 freq=400016019 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43024 bytes_read=134492 bytes_retransmit=0 bytes_invalid=0 send_seq=7142 receive_seq=7142 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999383 adj=49997355 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213674 bytes_read=6934666 bytes_retransmit=9 bytes_invalid=0 send_seq=29886 receive_seq=29886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997612 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=149106 bytes_read=4202845 bytes_retransmit=9 bytes_invalid=0 send_seq=20754 receive_seq=20754 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997448 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43291 bytes_read=1775868 bytes_retransmit=9 bytes_invalid=0 send_seq=7156 receive_seq=7156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43777 bytes_read=131845 bytes_retransmit=9 bytes_invalid=0 send_seq=7143 receive_seq=7143 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97869 bytes_read=2701343 bytes_retransmit=0 bytes_invalid=0 send_seq=11702 receive_seq=11702 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998638 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.4 th2: temp=62.0 th3: temp=59.6 sysload=0.20 cputime=543.248 memavail=7393956 print_time=6978.738 buffer_time=2.122 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 37 Hz
Testing frequency 38 Hz
Stats 6954.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33682846 bytes_read=5177784 bytes_retransmit=9 bytes_invalid=0 send_seq=634200 receive_seq=634200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=8980 freq=400016001 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43030 bytes_read=134508 bytes_retransmit=0 bytes_invalid=0 send_seq=7143 receive_seq=7143 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999383 adj=49997370 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213680 bytes_read=6934780 bytes_retransmit=9 bytes_invalid=0 send_seq=29887 receive_seq=29887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997641 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=149182 bytes_read=4205959 bytes_retransmit=9 bytes_invalid=0 send_seq=20765 receive_seq=20765 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000082 adj=63997582 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43297 bytes_read=1776117 bytes_retransmit=9 bytes_invalid=0 send_seq=7157 receive_seq=7157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43783 bytes_read=131861 bytes_retransmit=9 bytes_invalid=0 send_seq=7144 receive_seq=7144 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97875 bytes_read=2701699 bytes_retransmit=0 bytes_invalid=0 send_seq=11703 receive_seq=11703 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998662 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.5 th2: temp=62.0 th3: temp=59.4 sysload=0.20 cputime=543.364 memavail=7393956 print_time=6979.922 buffer_time=2.305 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 39 Hz
Stats 6955.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33691464 bytes_read=5178903 bytes_retransmit=9 bytes_invalid=0 send_seq=634356 receive_seq=634356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=7269 freq=400015977 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43036 bytes_read=134524 bytes_retransmit=0 bytes_invalid=0 send_seq=7144 receive_seq=7144 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999384 adj=49997399 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213686 bytes_read=6934888 bytes_retransmit=9 bytes_invalid=0 send_seq=29888 receive_seq=29888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997671 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=149258 bytes_read=4209008 bytes_retransmit=9 bytes_invalid=0 send_seq=20776 receive_seq=20776 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000079 adj=63997823 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43303 bytes_read=1776335 bytes_retransmit=9 bytes_invalid=0 send_seq=7158 receive_seq=7158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43789 bytes_read=131877 bytes_retransmit=9 bytes_invalid=0 send_seq=7145 receive_seq=7145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97881 bytes_read=2702055 bytes_retransmit=0 bytes_invalid=0 send_seq=11704 receive_seq=11704 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998680 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.5 th2: temp=61.8 th3: temp=59.6 sysload=0.19 cputime=543.473 memavail=7393960 print_time=6980.809 buffer_time=2.192 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.5 pwm=0.000
Testing frequency 40 Hz
Stats 6956.9: gcodein=0  mcu: mcu_awake=0.007 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33698981 bytes_read=5179893 bytes_retransmit=9 bytes_invalid=0 send_seq=634493 receive_seq=634493 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=8600 freq=400015963 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43042 bytes_read=134553 bytes_retransmit=0 bytes_invalid=0 send_seq=7145 receive_seq=7145 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999384 adj=49997447 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213692 bytes_read=6934994 bytes_retransmit=9 bytes_invalid=0 send_seq=29889 receive_seq=29889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997717 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=149334 bytes_read=4212075 bytes_retransmit=9 bytes_invalid=0 send_seq=20787 receive_seq=20787 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000079 adj=63997805 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43309 bytes_read=1776604 bytes_retransmit=9 bytes_invalid=0 send_seq=7159 receive_seq=7159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997702 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43795 bytes_read=131904 bytes_retransmit=9 bytes_invalid=0 send_seq=7146 receive_seq=7146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97887 bytes_read=2702411 bytes_retransmit=0 bytes_invalid=0 send_seq=11705 receive_seq=11705 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998698 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.4 th2: temp=62.0 th3: temp=59.5 sysload=0.19 cputime=543.579 memavail=7393960 print_time=6981.763 buffer_time=2.146 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6957.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33708094 bytes_read=5181029 bytes_retransmit=9 bytes_invalid=0 send_seq=634655 receive_seq=634655 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=6724 freq=400015953 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43048 bytes_read=134569 bytes_retransmit=0 bytes_invalid=0 send_seq=7146 receive_seq=7146 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999384 adj=49997459 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213698 bytes_read=6935087 bytes_retransmit=9 bytes_invalid=0 send_seq=29890 receive_seq=29890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997732 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=149410 bytes_read=4215131 bytes_retransmit=9 bytes_invalid=0 send_seq=20798 receive_seq=20798 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000079 adj=63997780 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43315 bytes_read=1776822 bytes_retransmit=9 bytes_invalid=0 send_seq=7160 receive_seq=7160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997705 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43801 bytes_read=131920 bytes_retransmit=9 bytes_invalid=0 send_seq=7147 receive_seq=7147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97893 bytes_read=2702767 bytes_retransmit=0 bytes_invalid=0 send_seq=11706 receive_seq=11706 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998705 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.4 th2: temp=61.9 th3: temp=59.4 sysload=0.19 cputime=543.689 memavail=7392952 print_time=6982.641 buffer_time=2.023 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 41 Hz
Testing frequency 42 Hz
Stats 6958.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33716927 bytes_read=5182153 bytes_retransmit=9 bytes_invalid=0 send_seq=634812 receive_seq=634812 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=8612 freq=400015940 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43054 bytes_read=134585 bytes_retransmit=0 bytes_invalid=0 send_seq=7147 receive_seq=7147 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999383 adj=49997461 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213704 bytes_read=6935193 bytes_retransmit=9 bytes_invalid=0 send_seq=29891 receive_seq=29891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997798 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=149486 bytes_read=4218172 bytes_retransmit=9 bytes_invalid=0 send_seq=20809 receive_seq=20809 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000084 adj=63997782 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43321 bytes_read=1777040 bytes_retransmit=9 bytes_invalid=0 send_seq=7161 receive_seq=7161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997703 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43807 bytes_read=131936 bytes_retransmit=9 bytes_invalid=0 send_seq=7148 receive_seq=7148 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97899 bytes_read=2703123 bytes_retransmit=0 bytes_invalid=0 send_seq=11707 receive_seq=11707 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998706 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.5 th2: temp=61.9 th3: temp=59.5 sysload=0.19 cputime=543.808 memavail=7392988 print_time=6983.852 buffer_time=2.233 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 43 Hz
Stats 6959.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33724970 bytes_read=5183188 bytes_retransmit=9 bytes_invalid=0 send_seq=634957 receive_seq=634957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=9952 freq=400015934 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43060 bytes_read=134601 bytes_retransmit=0 bytes_invalid=0 send_seq=7148 receive_seq=7148 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999382 adj=49997449 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213710 bytes_read=6935317 bytes_retransmit=9 bytes_invalid=0 send_seq=29892 receive_seq=29892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997983 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=149562 bytes_read=4221246 bytes_retransmit=9 bytes_invalid=0 send_seq=20820 receive_seq=20820 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000082 adj=63997785 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43327 bytes_read=1777329 bytes_retransmit=9 bytes_invalid=0 send_seq=7162 receive_seq=7162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43813 bytes_read=131952 bytes_retransmit=9 bytes_invalid=0 send_seq=7149 receive_seq=7149 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97905 bytes_read=2703479 bytes_retransmit=0 bytes_invalid=0 send_seq=11708 receive_seq=11708 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998700 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.3 th2: temp=62.0 th3: temp=59.5 sysload=0.19 cputime=543.914 memavail=7393000 print_time=6984.768 buffer_time=2.150 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6960.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33734674 bytes_read=5184333 bytes_retransmit=9 bytes_invalid=0 send_seq=635124 receive_seq=635124 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=7669 freq=400015930 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43066 bytes_read=134617 bytes_retransmit=0 bytes_invalid=0 send_seq=7149 receive_seq=7149 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999381 adj=49997444 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213716 bytes_read=6935417 bytes_retransmit=9 bytes_invalid=0 send_seq=29893 receive_seq=29893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997937 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=149638 bytes_read=4224302 bytes_retransmit=9 bytes_invalid=0 send_seq=20831 receive_seq=20831 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000080 adj=63997738 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43333 bytes_read=1777555 bytes_retransmit=9 bytes_invalid=0 send_seq=7163 receive_seq=7163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997762 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43819 bytes_read=131968 bytes_retransmit=9 bytes_invalid=0 send_seq=7150 receive_seq=7150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97911 bytes_read=2703835 bytes_retransmit=0 bytes_invalid=0 send_seq=11709 receive_seq=11709 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998699 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.4 th2: temp=61.9 th3: temp=59.5 sysload=0.17 cputime=544.023 memavail=7393000 print_time=6985.671 buffer_time=2.052 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 44 Hz
Testing frequency 45 Hz
Stats 6961.9: gcodein=0  mcu: mcu_awake=0.008 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33744439 bytes_read=5185547 bytes_retransmit=9 bytes_invalid=0 send_seq=635299 receive_seq=635299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=34 upcoming_bytes=8981 freq=400015925 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43072 bytes_read=134646 bytes_retransmit=0 bytes_invalid=0 send_seq=7150 receive_seq=7150 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999381 adj=49997429 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213722 bytes_read=6935531 bytes_retransmit=9 bytes_invalid=0 send_seq=29894 receive_seq=29894 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997906 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=149714 bytes_read=4227360 bytes_retransmit=9 bytes_invalid=0 send_seq=20842 receive_seq=20842 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000078 adj=63997697 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43339 bytes_read=1777789 bytes_retransmit=9 bytes_invalid=0 send_seq=7164 receive_seq=7164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997777 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43825 bytes_read=131995 bytes_retransmit=9 bytes_invalid=0 send_seq=7151 receive_seq=7151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97917 bytes_read=2704191 bytes_retransmit=0 bytes_invalid=0 send_seq=11710 receive_seq=11710 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998696 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.4 th2: temp=61.9 th3: temp=59.5 sysload=0.17 cputime=544.157 memavail=7394904 print_time=6986.867 buffer_time=2.248 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 46 Hz
Stats 6962.9: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33752488 bytes_read=5186608 bytes_retransmit=9 bytes_invalid=0 send_seq=635446 receive_seq=635446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=10609 freq=400015915 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43078 bytes_read=134662 bytes_retransmit=0 bytes_invalid=0 send_seq=7151 receive_seq=7151 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999381 adj=49997424 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213728 bytes_read=6935645 bytes_retransmit=9 bytes_invalid=0 send_seq=29895 receive_seq=29895 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997827 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=149783 bytes_read=4230496 bytes_retransmit=9 bytes_invalid=0 send_seq=20852 receive_seq=20852 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000075 adj=63997624 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43345 bytes_read=1778083 bytes_retransmit=9 bytes_invalid=0 send_seq=7165 receive_seq=7165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997742 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43831 bytes_read=132011 bytes_retransmit=9 bytes_invalid=0 send_seq=7152 receive_seq=7152 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97923 bytes_read=2704547 bytes_retransmit=0 bytes_invalid=0 send_seq=11711 receive_seq=11711 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998685 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.5 th2: temp=61.8 th3: temp=59.4 sysload=0.17 cputime=544.266 memavail=7394904 print_time=6987.789 buffer_time=2.168 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 6963.9: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33762598 bytes_read=5187808 bytes_retransmit=9 bytes_invalid=0 send_seq=635624 receive_seq=635624 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=8043 freq=400015907 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43084 bytes_read=134678 bytes_retransmit=0 bytes_invalid=0 send_seq=7152 receive_seq=7152 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999383 adj=49997437 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213734 bytes_read=6935745 bytes_retransmit=9 bytes_invalid=0 send_seq=29896 receive_seq=29896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997811 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=149859 bytes_read=4233554 bytes_retransmit=9 bytes_invalid=0 send_seq=20863 receive_seq=20863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000079 adj=63997605 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43351 bytes_read=1778317 bytes_retransmit=9 bytes_invalid=0 send_seq=7166 receive_seq=7166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997741 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43837 bytes_read=132027 bytes_retransmit=9 bytes_invalid=0 send_seq=7153 receive_seq=7153 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999470 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97929 bytes_read=2704903 bytes_retransmit=0 bytes_invalid=0 send_seq=11712 receive_seq=11712 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998694 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.5 th2: temp=61.9 th3: temp=59.3 sysload=0.17 cputime=544.376 memavail=7394904 print_time=6988.676 buffer_time=2.055 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 47 Hz
Testing frequency 48 Hz
Stats 6965.0: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33772538 bytes_read=5189037 bytes_retransmit=9 bytes_invalid=0 send_seq=635802 receive_seq=635802 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=9328 freq=400015931 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43090 bytes_read=134694 bytes_retransmit=0 bytes_invalid=0 send_seq=7153 receive_seq=7153 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999382 adj=49997461 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213740 bytes_read=6935873 bytes_retransmit=9 bytes_invalid=0 send_seq=29897 receive_seq=29897 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997791 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=149935 bytes_read=4236610 bytes_retransmit=9 bytes_invalid=0 send_seq=20874 receive_seq=20874 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000078 adj=63997655 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43357 bytes_read=1778566 bytes_retransmit=9 bytes_invalid=0 send_seq=7167 receive_seq=7167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997739 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43843 bytes_read=132043 bytes_retransmit=9 bytes_invalid=0 send_seq=7154 receive_seq=7154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999468 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97935 bytes_read=2705259 bytes_retransmit=0 bytes_invalid=0 send_seq=11713 receive_seq=11713 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998700 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.4 th2: temp=62.0 th3: temp=59.4 sysload=0.17 cputime=544.498 memavail=7394680 print_time=6989.886 buffer_time=2.259 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 49 Hz
Stats 6966.0: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33780805 bytes_read=5190087 bytes_retransmit=9 bytes_invalid=0 send_seq=635950 receive_seq=635950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=11040 freq=400015920 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43096 bytes_read=134710 bytes_retransmit=0 bytes_invalid=0 send_seq=7154 receive_seq=7154 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999382 adj=49997403 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213746 bytes_read=6935987 bytes_retransmit=9 bytes_invalid=0 send_seq=29898 receive_seq=29898 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997706 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150011 bytes_read=4239696 bytes_retransmit=9 bytes_invalid=0 send_seq=20885 receive_seq=20885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000077 adj=63997561 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43363 bytes_read=1778860 bytes_retransmit=9 bytes_invalid=0 send_seq=7168 receive_seq=7168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43849 bytes_read=132059 bytes_retransmit=9 bytes_invalid=0 send_seq=7155 receive_seq=7155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999472 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97941 bytes_read=2705615 bytes_retransmit=0 bytes_invalid=0 send_seq=11714 receive_seq=11714 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998664 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.3 th2: temp=61.8 th3: temp=59.5 sysload=0.16 cputime=544.609 memavail=7394680 print_time=6990.806 buffer_time=2.179 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6967.0: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33790938 bytes_read=5191287 bytes_retransmit=9 bytes_invalid=0 send_seq=636128 receive_seq=636128 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=8836 freq=400015914 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=43102 bytes_read=134738 bytes_retransmit=0 bytes_invalid=0 send_seq=7155 receive_seq=7155 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999381 adj=49997408 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213752 bytes_read=6936087 bytes_retransmit=9 bytes_invalid=0 send_seq=29899 receive_seq=29899 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997747 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150087 bytes_read=4242752 bytes_retransmit=9 bytes_invalid=0 send_seq=20896 receive_seq=20896 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000075 adj=63997566 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43369 bytes_read=1779094 bytes_retransmit=9 bytes_invalid=0 send_seq=7169 receive_seq=7169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43855 bytes_read=132086 bytes_retransmit=9 bytes_invalid=0 send_seq=7156 receive_seq=7156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999472 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97947 bytes_read=2705971 bytes_retransmit=0 bytes_invalid=0 send_seq=11715 receive_seq=11715 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998679 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.3 th2: temp=61.8 th3: temp=59.4 sysload=0.16 cputime=544.724 memavail=7394680 print_time=6991.705 buffer_time=2.077 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 50 Hz
Testing frequency 51 Hz
Stats 6968.0: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33801226 bytes_read=5192540 bytes_retransmit=9 bytes_invalid=0 send_seq=636309 receive_seq=636309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=10072 freq=400015912 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=43108 bytes_read=134753 bytes_retransmit=0 bytes_invalid=0 send_seq=7156 receive_seq=7156 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999381 adj=49997407 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213758 bytes_read=6936201 bytes_retransmit=9 bytes_invalid=0 send_seq=29900 receive_seq=29900 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997732 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150163 bytes_read=4245899 bytes_retransmit=9 bytes_invalid=0 send_seq=20907 receive_seq=20907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000072 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43375 bytes_read=1779328 bytes_retransmit=9 bytes_invalid=0 send_seq=7170 receive_seq=7170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997660 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43861 bytes_read=132102 bytes_retransmit=9 bytes_invalid=0 send_seq=7157 receive_seq=7157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999478 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97953 bytes_read=2706345 bytes_retransmit=0 bytes_invalid=0 send_seq=11716 receive_seq=11716 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998694 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.4 th2: temp=61.7 th3: temp=59.3 sysload=0.16 cputime=544.855 memavail=7395284 print_time=6992.897 buffer_time=2.260 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 52 Hz
Stats 6969.0: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33809879 bytes_read=5193620 bytes_retransmit=9 bytes_invalid=0 send_seq=636463 receive_seq=636463 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=11560 freq=400015904 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=43114 bytes_read=134768 bytes_retransmit=0 bytes_invalid=0 send_seq=7157 receive_seq=7157 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999382 adj=49997409 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213764 bytes_read=6936315 bytes_retransmit=9 bytes_invalid=0 send_seq=29901 receive_seq=29901 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997735 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150239 bytes_read=4248970 bytes_retransmit=9 bytes_invalid=0 send_seq=20918 receive_seq=20918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997517 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43381 bytes_read=1779622 bytes_retransmit=9 bytes_invalid=0 send_seq=7171 receive_seq=7171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43867 bytes_read=132118 bytes_retransmit=9 bytes_invalid=0 send_seq=7158 receive_seq=7158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999469 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97959 bytes_read=2706701 bytes_retransmit=0 bytes_invalid=0 send_seq=11717 receive_seq=11717 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998685 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=57.3 th1: temp=56.4 th2: temp=61.7 th3: temp=59.3 sysload=0.16 cputime=544.970 memavail=7395284 print_time=6993.813 buffer_time=2.176 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6970.0: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33820391 bytes_read=5194860 bytes_retransmit=9 bytes_invalid=0 send_seq=636649 receive_seq=636649 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=9407 freq=400015899 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=43120 bytes_read=134783 bytes_retransmit=0 bytes_invalid=0 send_seq=7158 receive_seq=7158 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999388 adj=49997430 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213770 bytes_read=6936429 bytes_retransmit=9 bytes_invalid=0 send_seq=29902 receive_seq=29902 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997729 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150315 bytes_read=4252026 bytes_retransmit=9 bytes_invalid=0 send_seq=20929 receive_seq=20929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000083 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=43387 bytes_read=1779871 bytes_retransmit=9 bytes_invalid=0 send_seq=7172 receive_seq=7172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43873 bytes_read=132134 bytes_retransmit=9 bytes_invalid=0 send_seq=7159 receive_seq=7159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97965 bytes_read=2707057 bytes_retransmit=0 bytes_invalid=0 send_seq=11718 receive_seq=11718 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998694 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.5 th2: temp=61.7 th3: temp=59.4 sysload=0.16 cputime=545.164 memavail=7395284 print_time=6994.712 buffer_time=2.075 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 53 Hz
Testing frequency 54 Hz
Stats 6971.0: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33830889 bytes_read=5196109 bytes_retransmit=9 bytes_invalid=0 send_seq=636831 receive_seq=636831 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=9216 freq=400015916 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=43126 bytes_read=134798 bytes_retransmit=0 bytes_invalid=0 send_seq=7159 receive_seq=7159 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999387 adj=49997515 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213776 bytes_read=6936557 bytes_retransmit=9 bytes_invalid=0 send_seq=29903 receive_seq=29903 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997729 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150391 bytes_read=4255098 bytes_retransmit=9 bytes_invalid=0 send_seq=20940 receive_seq=20940 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000081 adj=63997675 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=43393 bytes_read=1780105 bytes_retransmit=9 bytes_invalid=0 send_seq=7173 receive_seq=7173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43879 bytes_read=132150 bytes_retransmit=9 bytes_invalid=0 send_seq=7160 receive_seq=7160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999460 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97971 bytes_read=2707413 bytes_retransmit=0 bytes_invalid=0 send_seq=11719 receive_seq=11719 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998692 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=57.2 th1: temp=56.3 th2: temp=61.7 th3: temp=59.3 sysload=0.14 cputime=545.283 memavail=7395284 print_time=6995.625 buffer_time=1.987 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 55 Hz
Stats 6972.0: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33839942 bytes_read=5197224 bytes_retransmit=9 bytes_invalid=0 send_seq=636992 receive_seq=636992 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=12108 freq=400015913 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43132 bytes_read=134827 bytes_retransmit=0 bytes_invalid=0 send_seq=7160 receive_seq=7160 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999387 adj=49997459 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213782 bytes_read=6936657 bytes_retransmit=9 bytes_invalid=0 send_seq=29904 receive_seq=29904 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997669 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150467 bytes_read=4258168 bytes_retransmit=9 bytes_invalid=0 send_seq=20951 receive_seq=20951 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000078 adj=63997595 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=43399 bytes_read=1780399 bytes_retransmit=9 bytes_invalid=0 send_seq=7174 receive_seq=7174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997635 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43885 bytes_read=132177 bytes_retransmit=9 bytes_invalid=0 send_seq=7161 receive_seq=7161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97977 bytes_read=2707769 bytes_retransmit=0 bytes_invalid=0 send_seq=11720 receive_seq=11720 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998667 coil_temp=16.8 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.5 th2: temp=61.8 th3: temp=59.3 sysload=0.14 cputime=545.408 memavail=7395284 print_time=6996.823 buffer_time=2.185 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6973.0: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33850767 bytes_read=5198510 bytes_retransmit=9 bytes_invalid=0 send_seq=637184 receive_seq=637184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=9855 freq=400015893 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43138 bytes_read=134843 bytes_retransmit=0 bytes_invalid=0 send_seq=7161 receive_seq=7161 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999385 adj=49997434 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213788 bytes_read=6936757 bytes_retransmit=9 bytes_invalid=0 send_seq=29905 receive_seq=29905 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997664 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150543 bytes_read=4261300 bytes_retransmit=9 bytes_invalid=0 send_seq=20962 receive_seq=20962 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000078 adj=63997546 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=43405 bytes_read=1780633 bytes_retransmit=9 bytes_invalid=0 send_seq=7175 receive_seq=7175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43891 bytes_read=132193 bytes_retransmit=9 bytes_invalid=0 send_seq=7162 receive_seq=7162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97983 bytes_read=2708125 bytes_retransmit=0 bytes_invalid=0 send_seq=11721 receive_seq=11721 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998662 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.2 th1: temp=56.4 th2: temp=61.9 th3: temp=59.4 sysload=0.14 cputime=545.525 memavail=7395284 print_time=6997.741 buffer_time=2.103 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 56 Hz
Testing frequency 57 Hz
Stats 6974.0: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33861525 bytes_read=5199799 bytes_retransmit=9 bytes_invalid=0 send_seq=637374 receive_seq=637374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=11640 freq=400015998 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43144 bytes_read=134859 bytes_retransmit=0 bytes_invalid=0 send_seq=7162 receive_seq=7162 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999384 adj=49997444 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213794 bytes_read=6936885 bytes_retransmit=9 bytes_invalid=0 send_seq=29906 receive_seq=29906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997692 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150619 bytes_read=4264371 bytes_retransmit=9 bytes_invalid=0 send_seq=20973 receive_seq=20973 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000075 adj=63997584 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=43411 bytes_read=1780867 bytes_retransmit=9 bytes_invalid=0 send_seq=7176 receive_seq=7176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43897 bytes_read=132209 bytes_retransmit=9 bytes_invalid=0 send_seq=7163 receive_seq=7163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97989 bytes_read=2708481 bytes_retransmit=0 bytes_invalid=0 send_seq=11722 receive_seq=11722 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998682 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.012 th0: temp=57.0 th1: temp=56.4 th2: temp=61.8 th3: temp=59.4 sysload=0.14 cputime=545.655 memavail=7395292 print_time=6998.947 buffer_time=2.303 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 58 Hz
Stats 6975.0: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33870638 bytes_read=5200909 bytes_retransmit=9 bytes_invalid=0 send_seq=637534 receive_seq=637534 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=42 upcoming_bytes=13052 freq=400015992 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43150 bytes_read=134875 bytes_retransmit=0 bytes_invalid=0 send_seq=7163 receive_seq=7163 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999384 adj=49997261 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213800 bytes_read=6936999 bytes_retransmit=9 bytes_invalid=0 send_seq=29907 receive_seq=29907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997478 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150695 bytes_read=4267443 bytes_retransmit=9 bytes_invalid=0 send_seq=20984 receive_seq=20984 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997343 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43417 bytes_read=1781176 bytes_retransmit=9 bytes_invalid=0 send_seq=7177 receive_seq=7177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997532 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43903 bytes_read=132225 bytes_retransmit=9 bytes_invalid=0 send_seq=7164 receive_seq=7164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999408 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=97995 bytes_read=2708837 bytes_retransmit=0 bytes_invalid=0 send_seq=11723 receive_seq=11723 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998576 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.5 th2: temp=61.7 th3: temp=59.3 sysload=0.14 cputime=545.768 memavail=7395292 print_time=6999.836 buffer_time=2.192 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 59 Hz
Stats 6976.0: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33881965 bytes_read=5202214 bytes_retransmit=9 bytes_invalid=0 send_seq=637733 receive_seq=637733 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=10629 freq=400016006 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43156 bytes_read=134891 bytes_retransmit=0 bytes_invalid=0 send_seq=7164 receive_seq=7164 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999384 adj=49997283 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213806 bytes_read=6937099 bytes_retransmit=9 bytes_invalid=0 send_seq=29908 receive_seq=29908 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997500 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150771 bytes_read=4270501 bytes_retransmit=9 bytes_invalid=0 send_seq=20995 receive_seq=20995 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997351 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43423 bytes_read=1781410 bytes_retransmit=9 bytes_invalid=0 send_seq=7178 receive_seq=7178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997539 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43909 bytes_read=132241 bytes_retransmit=9 bytes_invalid=0 send_seq=7165 receive_seq=7165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999411 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98001 bytes_read=2709193 bytes_retransmit=0 bytes_invalid=0 send_seq=11724 receive_seq=11724 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998590 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.012 th0: temp=57.1 th1: temp=56.3 th2: temp=61.9 th3: temp=59.3 sysload=0.13 cputime=545.888 memavail=7395292 print_time=7000.758 buffer_time=2.114 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 60 Hz
Stats 6977.0: gcodein=0  mcu: mcu_awake=0.009 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33893184 bytes_read=5203553 bytes_retransmit=9 bytes_invalid=0 send_seq=637933 receive_seq=637933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=10131 freq=400015982 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43162 bytes_read=134907 bytes_retransmit=0 bytes_invalid=0 send_seq=7165 receive_seq=7165 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999383 adj=49997272 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213812 bytes_read=6937227 bytes_retransmit=9 bytes_invalid=0 send_seq=29909 receive_seq=29909 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997518 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150847 bytes_read=4273574 bytes_retransmit=9 bytes_invalid=0 send_seq=21006 receive_seq=21006 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997313 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43429 bytes_read=1781644 bytes_retransmit=9 bytes_invalid=0 send_seq=7179 receive_seq=7179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997526 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43915 bytes_read=132268 bytes_retransmit=9 bytes_invalid=0 send_seq=7166 receive_seq=7166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999408 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98007 bytes_read=2709549 bytes_retransmit=0 bytes_invalid=0 send_seq=11725 receive_seq=11725 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998580 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.012 th0: temp=57.0 th1: temp=56.4 th2: temp=61.8 th3: temp=59.3 sysload=0.13 cputime=546.008 memavail=7394788 print_time=7001.641 buffer_time=1.997 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 61 Hz
Stats 6978.0: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33902440 bytes_read=5204692 bytes_retransmit=9 bytes_invalid=0 send_seq=638096 receive_seq=638096 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=13631 freq=400015967 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=43168 bytes_read=134936 bytes_retransmit=0 bytes_invalid=0 send_seq=7166 receive_seq=7166 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999382 adj=49997319 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213818 bytes_read=6937327 bytes_retransmit=9 bytes_invalid=0 send_seq=29910 receive_seq=29910 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997571 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150916 bytes_read=4276639 bytes_retransmit=9 bytes_invalid=0 send_seq=21016 receive_seq=21016 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000078 adj=63997395 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43435 bytes_read=1781938 bytes_retransmit=9 bytes_invalid=0 send_seq=7180 receive_seq=7180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997568 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43921 bytes_read=132284 bytes_retransmit=9 bytes_invalid=0 send_seq=7167 receive_seq=7167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999417 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98013 bytes_read=2709905 bytes_retransmit=0 bytes_invalid=0 send_seq=11726 receive_seq=11726 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998623 coil_temp=16.8 refs=0 mcu_temp=20.18 supply_voltage=3.012 th0: temp=56.7 th1: temp=56.5 th2: temp=61.8 th3: temp=59.3 sysload=0.13 cputime=546.137 memavail=7395076 print_time=7002.856 buffer_time=2.211 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 62 Hz
Stats 6979.0: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33913894 bytes_read=5206014 bytes_retransmit=9 bytes_invalid=0 send_seq=638299 receive_seq=638299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=11267 freq=400015958 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=43174 bytes_read=134952 bytes_retransmit=0 bytes_invalid=0 send_seq=7167 receive_seq=7167 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999382 adj=49997348 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213824 bytes_read=6937427 bytes_retransmit=9 bytes_invalid=0 send_seq=29911 receive_seq=29911 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997624 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=150992 bytes_read=4279753 bytes_retransmit=9 bytes_invalid=0 send_seq=21027 receive_seq=21027 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000076 adj=63997543 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43441 bytes_read=1782172 bytes_retransmit=9 bytes_invalid=0 send_seq=7181 receive_seq=7181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997604 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43927 bytes_read=132300 bytes_retransmit=9 bytes_invalid=0 send_seq=7168 receive_seq=7168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98019 bytes_read=2710261 bytes_retransmit=0 bytes_invalid=0 send_seq=11727 receive_seq=11727 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998645 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.012 th0: temp=57.0 th1: temp=56.3 th2: temp=61.8 th3: temp=59.3 sysload=0.13 cputime=546.273 memavail=7395860 print_time=7003.766 buffer_time=2.121 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6980.0: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33925416 bytes_read=5207378 bytes_retransmit=9 bytes_invalid=0 send_seq=638504 receive_seq=638504 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=10919 freq=400016035 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=43180 bytes_read=134968 bytes_retransmit=0 bytes_invalid=0 send_seq=7168 receive_seq=7168 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999381 adj=49997373 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213830 bytes_read=6937569 bytes_retransmit=9 bytes_invalid=0 send_seq=29912 receive_seq=29912 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997834 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151068 bytes_read=4282826 bytes_retransmit=9 bytes_invalid=0 send_seq=21038 receive_seq=21038 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000074 adj=63997541 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=43447 bytes_read=1782421 bytes_retransmit=9 bytes_invalid=0 send_seq=7182 receive_seq=7182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997620 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43933 bytes_read=132316 bytes_retransmit=9 bytes_invalid=0 send_seq=7169 receive_seq=7169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98025 bytes_read=2710617 bytes_retransmit=0 bytes_invalid=0 send_seq=11728 receive_seq=11728 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998655 coil_temp=16.8 refs=0 mcu_temp=20.16 supply_voltage=3.012 th0: temp=57.1 th1: temp=56.3 th2: temp=61.8 th3: temp=59.3 sysload=0.13 cputime=546.390 memavail=7395944 print_time=7004.658 buffer_time=2.013 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 63 Hz
Testing frequency 64 Hz
Stats 6981.0: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33935033 bytes_read=5208548 bytes_retransmit=9 bytes_invalid=0 send_seq=638676 receive_seq=638676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=28 upcoming_bytes=14291 freq=400016030 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=43186 bytes_read=134984 bytes_retransmit=0 bytes_invalid=0 send_seq=7169 receive_seq=7169 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999380 adj=49997229 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213836 bytes_read=6937669 bytes_retransmit=9 bytes_invalid=0 send_seq=29913 receive_seq=29913 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997631 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151144 bytes_read=4285897 bytes_retransmit=9 bytes_invalid=0 send_seq=21049 receive_seq=21049 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997341 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=43453 bytes_read=1782715 bytes_retransmit=9 bytes_invalid=0 send_seq=7183 receive_seq=7183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997493 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43939 bytes_read=132332 bytes_retransmit=9 bytes_invalid=0 send_seq=7170 receive_seq=7170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999398 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98031 bytes_read=2710957 bytes_retransmit=0 bytes_invalid=0 send_seq=11729 receive_seq=11729 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998572 coil_temp=16.8 refs=0 mcu_temp=20.16 supply_voltage=3.012 th0: temp=57.3 th1: temp=56.4 th2: temp=61.7 th3: temp=59.4 sysload=0.12 cputime=546.522 memavail=7395944 print_time=7005.855 buffer_time=2.209 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 65 Hz
Stats 6982.0: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33946959 bytes_read=5209903 bytes_retransmit=9 bytes_invalid=0 send_seq=638885 receive_seq=638885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=12019 freq=400016026 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=43192 bytes_read=135000 bytes_retransmit=0 bytes_invalid=0 send_seq=7170 receive_seq=7170 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999380 adj=49997275 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213842 bytes_read=6937769 bytes_retransmit=9 bytes_invalid=0 send_seq=29914 receive_seq=29914 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997631 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151220 bytes_read=4288954 bytes_retransmit=9 bytes_invalid=0 send_seq=21060 receive_seq=21060 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000076 adj=63997385 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=43459 bytes_read=1782949 bytes_retransmit=9 bytes_invalid=0 send_seq=7184 receive_seq=7184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997532 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43945 bytes_read=132359 bytes_retransmit=9 bytes_invalid=0 send_seq=7171 receive_seq=7171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999409 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98037 bytes_read=2711313 bytes_retransmit=0 bytes_invalid=0 send_seq=11730 receive_seq=11730 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998594 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.4 th2: temp=62.1 th3: temp=59.3 sysload=0.12 cputime=546.646 memavail=7395944 print_time=7006.784 buffer_time=2.137 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6983.0: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33958673 bytes_read=5211283 bytes_retransmit=9 bytes_invalid=0 send_seq=639090 receive_seq=639090 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=11394 freq=400016001 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43198 bytes_read=135029 bytes_retransmit=0 bytes_invalid=0 send_seq=7171 receive_seq=7171 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999380 adj=49997293 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213848 bytes_read=6937897 bytes_retransmit=9 bytes_invalid=0 send_seq=29915 receive_seq=29915 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997624 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151296 bytes_read=4292044 bytes_retransmit=9 bytes_invalid=0 send_seq=21071 receive_seq=21071 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997453 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=43465 bytes_read=1783183 bytes_retransmit=9 bytes_invalid=0 send_seq=7185 receive_seq=7185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997547 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43951 bytes_read=132375 bytes_retransmit=9 bytes_invalid=0 send_seq=7172 receive_seq=7172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999412 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98043 bytes_read=2711669 bytes_retransmit=0 bytes_invalid=0 send_seq=11731 receive_seq=11731 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998607 coil_temp=16.8 refs=0 mcu_temp=20.17 supply_voltage=3.011 th0: temp=57.2 th1: temp=56.4 th2: temp=61.7 th3: temp=59.3 sysload=0.12 cputime=546.765 memavail=7395944 print_time=7007.651 buffer_time=2.004 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 66 Hz
Testing frequency 67 Hz
Stats 6984.0: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33968577 bytes_read=5212458 bytes_retransmit=9 bytes_invalid=0 send_seq=639263 receive_seq=639263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=14897 freq=400015996 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43204 bytes_read=135045 bytes_retransmit=0 bytes_invalid=0 send_seq=7172 receive_seq=7172 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999379 adj=49997337 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213854 bytes_read=6937997 bytes_retransmit=9 bytes_invalid=0 send_seq=29916 receive_seq=29916 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997668 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151372 bytes_read=4295115 bytes_retransmit=9 bytes_invalid=0 send_seq=21082 receive_seq=21082 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997478 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=43471 bytes_read=1783477 bytes_retransmit=9 bytes_invalid=0 send_seq=7186 receive_seq=7186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997588 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43957 bytes_read=132391 bytes_retransmit=9 bytes_invalid=0 send_seq=7173 receive_seq=7173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999423 Octopus_Pro_H723_V1.1: temp=29.0 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98049 bytes_read=2712025 bytes_retransmit=0 bytes_invalid=0 send_seq=11732 receive_seq=11732 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998638 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=57.3 th1: temp=56.5 th2: temp=61.8 th3: temp=59.2 sysload=0.12 cputime=546.899 memavail=7395944 print_time=7008.872 buffer_time=2.225 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 68 Hz
Stats 6985.0: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33980790 bytes_read=5213847 bytes_retransmit=9 bytes_invalid=0 send_seq=639476 receive_seq=639476 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=12876 freq=400015981 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43210 bytes_read=135061 bytes_retransmit=0 bytes_invalid=0 send_seq=7173 receive_seq=7173 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999379 adj=49997355 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213860 bytes_read=6938111 bytes_retransmit=9 bytes_invalid=0 send_seq=29917 receive_seq=29917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997675 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151448 bytes_read=4298172 bytes_retransmit=9 bytes_invalid=0 send_seq=21093 receive_seq=21093 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997475 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43477 bytes_read=1783726 bytes_retransmit=9 bytes_invalid=0 send_seq=7187 receive_seq=7187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997603 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43963 bytes_read=132407 bytes_retransmit=9 bytes_invalid=0 send_seq=7174 receive_seq=7174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98055 bytes_read=2712381 bytes_retransmit=0 bytes_invalid=0 send_seq=11733 receive_seq=11733 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998649 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.5 th2: temp=61.7 th3: temp=59.4 sysload=0.12 cputime=547.026 memavail=7395944 print_time=7009.798 buffer_time=2.150 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6986.0: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=33992795 bytes_read=5215237 bytes_retransmit=9 bytes_invalid=0 send_seq=639689 receive_seq=639689 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=52 upcoming_bytes=12083 freq=400015981 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43216 bytes_read=135077 bytes_retransmit=0 bytes_invalid=0 send_seq=7174 receive_seq=7174 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999380 adj=49997378 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213866 bytes_read=6938239 bytes_retransmit=9 bytes_invalid=0 send_seq=29918 receive_seq=29918 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997689 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151524 bytes_read=4301242 bytes_retransmit=9 bytes_invalid=0 send_seq=21104 receive_seq=21104 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997478 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43483 bytes_read=1783960 bytes_retransmit=9 bytes_invalid=0 send_seq=7188 receive_seq=7188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997623 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43969 bytes_read=132423 bytes_retransmit=9 bytes_invalid=0 send_seq=7175 receive_seq=7175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98061 bytes_read=2712737 bytes_retransmit=0 bytes_invalid=0 send_seq=11734 receive_seq=11734 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998676 coil_temp=16.8 refs=0 mcu_temp=20.19 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.4 th2: temp=61.8 th3: temp=59.3 sysload=0.11 cputime=547.147 memavail=7395944 print_time=7010.677 buffer_time=2.029 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 69 Hz
Testing frequency 70 Hz
Stats 6987.0: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34003059 bytes_read=5216457 bytes_retransmit=9 bytes_invalid=0 send_seq=639871 receive_seq=639871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=49 upcoming_bytes=15779 freq=400015971 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43222 bytes_read=135093 bytes_retransmit=0 bytes_invalid=0 send_seq=7175 receive_seq=7175 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999378 adj=49997387 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213872 bytes_read=6938339 bytes_retransmit=9 bytes_invalid=0 send_seq=29919 receive_seq=29919 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997682 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151600 bytes_read=4304371 bytes_retransmit=9 bytes_invalid=0 send_seq=21115 receive_seq=21115 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997482 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43489 bytes_read=1784254 bytes_retransmit=9 bytes_invalid=0 send_seq=7189 receive_seq=7189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43975 bytes_read=132450 bytes_retransmit=9 bytes_invalid=0 send_seq=7176 receive_seq=7176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98067 bytes_read=2713093 bytes_retransmit=0 bytes_invalid=0 send_seq=11735 receive_seq=11735 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998670 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.4 th2: temp=61.8 th3: temp=59.2 sysload=0.11 cputime=547.282 memavail=7395944 print_time=7011.878 buffer_time=2.229 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 71 Hz
Stats 6988.0: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34015608 bytes_read=5217887 bytes_retransmit=9 bytes_invalid=0 send_seq=640089 receive_seq=640089 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=13736 freq=400016044 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000013 bytes_write=43228 bytes_read=135122 bytes_retransmit=0 bytes_invalid=0 send_seq=7176 receive_seq=7176 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999378 adj=49997384 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213878 bytes_read=6938439 bytes_retransmit=9 bytes_invalid=0 send_seq=29920 receive_seq=29920 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997682 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151669 bytes_read=4307421 bytes_retransmit=9 bytes_invalid=0 send_seq=21125 receive_seq=21125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997485 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43495 bytes_read=1784488 bytes_retransmit=9 bytes_invalid=0 send_seq=7190 receive_seq=7190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43981 bytes_read=132466 bytes_retransmit=9 bytes_invalid=0 send_seq=7177 receive_seq=7177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98073 bytes_read=2713449 bytes_retransmit=0 bytes_invalid=0 send_seq=11736 receive_seq=11736 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998673 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.5 th2: temp=61.9 th3: temp=59.2 sysload=0.11 cputime=547.410 memavail=7396520 print_time=7012.809 buffer_time=2.160 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6989.0: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34028196 bytes_read=5219313 bytes_retransmit=9 bytes_invalid=0 send_seq=640310 receive_seq=640310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=12571 freq=400016031 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000013 bytes_write=43234 bytes_read=135138 bytes_retransmit=0 bytes_invalid=0 send_seq=7177 receive_seq=7177 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999378 adj=49997264 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=213884 bytes_read=6938567 bytes_retransmit=9 bytes_invalid=0 send_seq=29921 receive_seq=29921 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997518 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151745 bytes_read=4310495 bytes_retransmit=9 bytes_invalid=0 send_seq=21136 receive_seq=21136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997320 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43501 bytes_read=1784722 bytes_retransmit=9 bytes_invalid=0 send_seq=7191 receive_seq=7191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997529 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43987 bytes_read=132482 bytes_retransmit=9 bytes_invalid=0 send_seq=7178 receive_seq=7178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999406 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98079 bytes_read=2713805 bytes_retransmit=0 bytes_invalid=0 send_seq=11737 receive_seq=11737 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998593 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.4 th2: temp=61.7 th3: temp=59.3 sysload=0.11 cputime=547.532 memavail=7396624 print_time=7013.693 buffer_time=2.045 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 72 Hz
Testing frequency 73 Hz
Stats 6990.0: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34038570 bytes_read=5220537 bytes_retransmit=9 bytes_invalid=0 send_seq=640493 receive_seq=640493 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=58 upcoming_bytes=16454 freq=400016008 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000013 bytes_write=43240 bytes_read=135154 bytes_retransmit=0 bytes_invalid=0 send_seq=7178 receive_seq=7178 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999378 adj=49997299 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213890 bytes_read=6938681 bytes_retransmit=9 bytes_invalid=0 send_seq=29922 receive_seq=29922 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997577 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151821 bytes_read=4313567 bytes_retransmit=9 bytes_invalid=0 send_seq=21147 receive_seq=21147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997362 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43507 bytes_read=1785031 bytes_retransmit=9 bytes_invalid=0 send_seq=7192 receive_seq=7192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997562 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43993 bytes_read=132498 bytes_retransmit=9 bytes_invalid=0 send_seq=7179 receive_seq=7179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999415 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98085 bytes_read=2714161 bytes_retransmit=0 bytes_invalid=0 send_seq=11738 receive_seq=11738 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998669 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.3 th2: temp=61.7 th3: temp=59.3 sysload=0.11 cputime=547.670 memavail=7396624 print_time=7014.896 buffer_time=2.247 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 74 Hz
Stats 6991.0: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34051373 bytes_read=5221981 bytes_retransmit=9 bytes_invalid=0 send_seq=640717 receive_seq=640717 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=15052 freq=400015996 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000013 bytes_write=43246 bytes_read=135170 bytes_retransmit=0 bytes_invalid=0 send_seq=7179 receive_seq=7179 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999378 adj=49997354 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213896 bytes_read=6938781 bytes_retransmit=9 bytes_invalid=0 send_seq=29923 receive_seq=29923 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997661 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151897 bytes_read=4316624 bytes_retransmit=9 bytes_invalid=0 send_seq=21158 receive_seq=21158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997448 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43513 bytes_read=1785265 bytes_retransmit=9 bytes_invalid=0 send_seq=7193 receive_seq=7193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=43999 bytes_read=132514 bytes_retransmit=9 bytes_invalid=0 send_seq=7180 receive_seq=7180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98091 bytes_read=2714517 bytes_retransmit=0 bytes_invalid=0 send_seq=11739 receive_seq=11739 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998735 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=57.2 th1: temp=56.5 th2: temp=61.7 th3: temp=59.3 sysload=0.18 cputime=547.799 memavail=7396624 print_time=7015.833 buffer_time=2.184 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 6992.0: gcodein=0  mcu: mcu_awake=0.010 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34064310 bytes_read=5223436 bytes_retransmit=9 bytes_invalid=0 send_seq=640943 receive_seq=640943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=13372 freq=400016022 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000013 bytes_write=43252 bytes_read=135186 bytes_retransmit=0 bytes_invalid=0 send_seq=7180 receive_seq=7180 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999376 adj=49997376 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213902 bytes_read=6938909 bytes_retransmit=9 bytes_invalid=0 send_seq=29924 receive_seq=29924 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997673 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=151973 bytes_read=4319697 bytes_retransmit=9 bytes_invalid=0 send_seq=21169 receive_seq=21169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997455 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43519 bytes_read=1785499 bytes_retransmit=9 bytes_invalid=0 send_seq=7194 receive_seq=7194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44005 bytes_read=132541 bytes_retransmit=9 bytes_invalid=0 send_seq=7181 receive_seq=7181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98097 bytes_read=2714873 bytes_retransmit=0 bytes_invalid=0 send_seq=11740 receive_seq=11740 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998735 coil_temp=16.8 refs=0 mcu_temp=20.20 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.5 th2: temp=61.9 th3: temp=59.4 sysload=0.18 cputime=547.922 memavail=7396624 print_time=7016.709 buffer_time=2.059 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 75 Hz
Testing frequency 76 Hz
Stats 6993.0: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34075027 bytes_read=5224687 bytes_retransmit=9 bytes_invalid=0 send_seq=641128 receive_seq=641128 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=17182 freq=400016029 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43258 bytes_read=135215 bytes_retransmit=0 bytes_invalid=0 send_seq=7181 receive_seq=7181 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999376 adj=49997318 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213908 bytes_read=6939009 bytes_retransmit=9 bytes_invalid=0 send_seq=29925 receive_seq=29925 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997619 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152049 bytes_read=4322844 bytes_retransmit=9 bytes_invalid=0 send_seq=21180 receive_seq=21180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997403 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43525 bytes_read=1785793 bytes_retransmit=9 bytes_invalid=0 send_seq=7195 receive_seq=7195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997604 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44011 bytes_read=132557 bytes_retransmit=9 bytes_invalid=0 send_seq=7182 receive_seq=7182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98103 bytes_read=2715229 bytes_retransmit=0 bytes_invalid=0 send_seq=11741 receive_seq=11741 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998698 coil_temp=16.8 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.5 th2: temp=61.8 th3: temp=59.3 sysload=0.18 cputime=548.061 memavail=7396624 print_time=7017.903 buffer_time=2.245 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 77 Hz
Stats 6994.0: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34088191 bytes_read=5226171 bytes_retransmit=9 bytes_invalid=0 send_seq=641357 receive_seq=641357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=15688 freq=400016016 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43264 bytes_read=135231 bytes_retransmit=0 bytes_invalid=0 send_seq=7182 receive_seq=7182 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999375 adj=49997316 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213914 bytes_read=6939109 bytes_retransmit=9 bytes_invalid=0 send_seq=29926 receive_seq=29926 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997630 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152125 bytes_read=4325903 bytes_retransmit=9 bytes_invalid=0 send_seq=21191 receive_seq=21191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997394 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43531 bytes_read=1786027 bytes_retransmit=9 bytes_invalid=0 send_seq=7196 receive_seq=7196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997594 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44017 bytes_read=132573 bytes_retransmit=9 bytes_invalid=0 send_seq=7183 receive_seq=7183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98109 bytes_read=2715585 bytes_retransmit=0 bytes_invalid=0 send_seq=11742 receive_seq=11742 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998673 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=57.5 th1: temp=56.5 th2: temp=61.7 th3: temp=59.3 sysload=0.18 cputime=548.191 memavail=7396148 print_time=7018.836 buffer_time=2.178 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 6995.0: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34101518 bytes_read=5227632 bytes_retransmit=9 bytes_invalid=0 send_seq=641585 receive_seq=641585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=13776 freq=400016007 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43276 bytes_read=135263 bytes_retransmit=0 bytes_invalid=0 send_seq=7184 receive_seq=7184 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999376 adj=49997333 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213926 bytes_read=6939267 bytes_retransmit=9 bytes_invalid=0 send_seq=29928 receive_seq=29928 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997704 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152207 bytes_read=4329003 bytes_retransmit=9 bytes_invalid=0 send_seq=21203 receive_seq=21203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997416 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43543 bytes_read=1786292 bytes_retransmit=9 bytes_invalid=0 send_seq=7198 receive_seq=7198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997612 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44029 bytes_read=132605 bytes_retransmit=9 bytes_invalid=0 send_seq=7185 receive_seq=7185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98121 bytes_read=2715957 bytes_retransmit=0 bytes_invalid=0 send_seq=11744 receive_seq=11744 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998678 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.3 th1: temp=56.5 th2: temp=61.7 th3: temp=59.4 sysload=0.18 cputime=548.317 memavail=7396148 print_time=7019.704 buffer_time=2.045 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 78 Hz
Testing frequency 79 Hz
Stats 6996.0: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34112479 bytes_read=5228912 bytes_retransmit=9 bytes_invalid=0 send_seq=641779 receive_seq=641779 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=14844 freq=400015992 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43282 bytes_read=135279 bytes_retransmit=0 bytes_invalid=0 send_seq=7185 receive_seq=7185 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999376 adj=49997360 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213932 bytes_read=6939367 bytes_retransmit=9 bytes_invalid=0 send_seq=29929 receive_seq=29929 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997716 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152283 bytes_read=4332060 bytes_retransmit=9 bytes_invalid=0 send_seq=21214 receive_seq=21214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997441 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43549 bytes_read=1786586 bytes_retransmit=9 bytes_invalid=0 send_seq=7199 receive_seq=7199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44035 bytes_read=132621 bytes_retransmit=9 bytes_invalid=0 send_seq=7186 receive_seq=7186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98127 bytes_read=2716313 bytes_retransmit=0 bytes_invalid=0 send_seq=11745 receive_seq=11745 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998676 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.8 th1: temp=56.3 th2: temp=61.8 th3: temp=59.3 sysload=0.25 cputime=548.456 memavail=7390636 print_time=7020.654 buffer_time=1.995 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 80 Hz
Stats 6997.0: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34125941 bytes_read=5230426 bytes_retransmit=9 bytes_invalid=0 send_seq=642014 receive_seq=642014 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=29 upcoming_bytes=16255 freq=400015975 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43288 bytes_read=135295 bytes_retransmit=0 bytes_invalid=0 send_seq=7186 receive_seq=7186 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999383 adj=49997391 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213938 bytes_read=6939467 bytes_retransmit=9 bytes_invalid=0 send_seq=29930 receive_seq=29930 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997734 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152359 bytes_read=4335118 bytes_retransmit=9 bytes_invalid=0 send_seq=21225 receive_seq=21225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997516 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43555 bytes_read=1786820 bytes_retransmit=9 bytes_invalid=0 send_seq=7200 receive_seq=7200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44041 bytes_read=132648 bytes_retransmit=9 bytes_invalid=0 send_seq=7187 receive_seq=7187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98133 bytes_read=2716669 bytes_retransmit=0 bytes_invalid=0 send_seq=11746 receive_seq=11746 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998677 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.4 th2: temp=61.8 th3: temp=59.3 sysload=0.25 cputime=548.601 memavail=7396520 print_time=7021.849 buffer_time=2.189 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 6998.0: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34139383 bytes_read=5231927 bytes_retransmit=9 bytes_invalid=0 send_seq=642249 receive_seq=642249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=57 upcoming_bytes=14167 freq=400015965 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43294 bytes_read=135324 bytes_retransmit=0 bytes_invalid=0 send_seq=7187 receive_seq=7187 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999382 adj=49997504 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213944 bytes_read=6939595 bytes_retransmit=9 bytes_invalid=0 send_seq=29931 receive_seq=29931 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997754 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152435 bytes_read=4338219 bytes_retransmit=9 bytes_invalid=0 send_seq=21236 receive_seq=21236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000073 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43561 bytes_read=1787054 bytes_retransmit=9 bytes_invalid=0 send_seq=7201 receive_seq=7201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44047 bytes_read=132664 bytes_retransmit=9 bytes_invalid=0 send_seq=7188 receive_seq=7188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98139 bytes_read=2717025 bytes_retransmit=0 bytes_invalid=0 send_seq=11747 receive_seq=11747 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998684 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.2 th1: temp=56.4 th2: temp=61.8 th3: temp=59.3 sysload=0.25 cputime=548.728 memavail=7395260 print_time=7022.724 buffer_time=2.064 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 81 Hz
Stats 6999.0: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34150453 bytes_read=5233222 bytes_retransmit=9 bytes_invalid=0 send_seq=642446 receive_seq=642446 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=20 upcoming_bytes=15558 freq=400015951 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43300 bytes_read=135340 bytes_retransmit=0 bytes_invalid=0 send_seq=7188 receive_seq=7188 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999381 adj=49997494 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213950 bytes_read=6939695 bytes_retransmit=9 bytes_invalid=0 send_seq=29932 receive_seq=29932 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997749 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152511 bytes_read=4341275 bytes_retransmit=9 bytes_invalid=0 send_seq=21247 receive_seq=21247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000091 adj=63997712 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43567 bytes_read=1787348 bytes_retransmit=9 bytes_invalid=0 send_seq=7202 receive_seq=7202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44053 bytes_read=132680 bytes_retransmit=9 bytes_invalid=0 send_seq=7189 receive_seq=7189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98145 bytes_read=2717381 bytes_retransmit=0 bytes_invalid=0 send_seq=11748 receive_seq=11748 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998686 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.3 th2: temp=61.8 th3: temp=59.3 sysload=0.25 cputime=548.854 memavail=7395260 print_time=7023.660 buffer_time=1.999 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 82 Hz
Testing frequency 83 Hz
Stats 7000.0: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34164220 bytes_read=5234746 bytes_retransmit=9 bytes_invalid=0 send_seq=642684 receive_seq=642684 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=17232 freq=400015955 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43306 bytes_read=135356 bytes_retransmit=0 bytes_invalid=0 send_seq=7189 receive_seq=7189 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999381 adj=49997484 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213956 bytes_read=6939809 bytes_retransmit=9 bytes_invalid=0 send_seq=29933 receive_seq=29933 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997755 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152587 bytes_read=4344390 bytes_retransmit=9 bytes_invalid=0 send_seq=21258 receive_seq=21258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000087 adj=63997948 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=43573 bytes_read=1787597 bytes_retransmit=9 bytes_invalid=0 send_seq=7203 receive_seq=7203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44059 bytes_read=132696 bytes_retransmit=9 bytes_invalid=0 send_seq=7190 receive_seq=7190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98151 bytes_read=2717737 bytes_retransmit=0 bytes_invalid=0 send_seq=11749 receive_seq=11749 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998687 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.2 th1: temp=56.5 th2: temp=61.6 th3: temp=59.3 sysload=0.25 cputime=549.000 memavail=7395260 print_time=7024.869 buffer_time=2.207 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 84 Hz
Stats 7001.0: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34178013 bytes_read=5236221 bytes_retransmit=9 bytes_invalid=0 send_seq=642918 receive_seq=642917 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=14410 freq=400015964 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43312 bytes_read=135372 bytes_retransmit=0 bytes_invalid=0 send_seq=7190 receive_seq=7190 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999380 adj=49997443 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213962 bytes_read=6939937 bytes_retransmit=9 bytes_invalid=0 send_seq=29934 receive_seq=29934 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997713 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152663 bytes_read=4347476 bytes_retransmit=9 bytes_invalid=0 send_seq=21269 receive_seq=21269 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000083 adj=63997765 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=43579 bytes_read=1787831 bytes_retransmit=9 bytes_invalid=0 send_seq=7204 receive_seq=7204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44065 bytes_read=132712 bytes_retransmit=9 bytes_invalid=0 send_seq=7191 receive_seq=7191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98157 bytes_read=2718093 bytes_retransmit=0 bytes_invalid=0 send_seq=11750 receive_seq=11750 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998665 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.2 th2: temp=61.7 th3: temp=59.4 sysload=0.23 cputime=549.131 memavail=7395260 print_time=7025.731 buffer_time=2.069 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7002.0: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34189158 bytes_read=5237516 bytes_retransmit=9 bytes_invalid=0 send_seq=643114 receive_seq=643114 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=16105 freq=400015967 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43318 bytes_read=135388 bytes_retransmit=0 bytes_invalid=0 send_seq=7191 receive_seq=7191 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999380 adj=49997419 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213968 bytes_read=6940037 bytes_retransmit=9 bytes_invalid=0 send_seq=29935 receive_seq=29935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997674 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152732 bytes_read=4350509 bytes_retransmit=9 bytes_invalid=0 send_seq=21279 receive_seq=21279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000080 adj=63997676 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=43585 bytes_read=1788125 bytes_retransmit=9 bytes_invalid=0 send_seq=7205 receive_seq=7205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997648 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44071 bytes_read=132739 bytes_retransmit=9 bytes_invalid=0 send_seq=7192 receive_seq=7192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98163 bytes_read=2718449 bytes_retransmit=0 bytes_invalid=0 send_seq=11751 receive_seq=11751 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998653 coil_temp=16.8 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.4 th2: temp=61.7 th3: temp=59.3 sysload=0.23 cputime=549.257 memavail=7395272 print_time=7026.666 buffer_time=2.004 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 85 Hz
Testing frequency 86 Hz
Stats 7003.0: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34202929 bytes_read=5239071 bytes_retransmit=9 bytes_invalid=0 send_seq=643354 receive_seq=643354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=18175 freq=400015965 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43324 bytes_read=135417 bytes_retransmit=0 bytes_invalid=0 send_seq=7192 receive_seq=7192 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999380 adj=49997403 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213974 bytes_read=6940137 bytes_retransmit=9 bytes_invalid=0 send_seq=29936 receive_seq=29936 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997649 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152808 bytes_read=4353583 bytes_retransmit=9 bytes_invalid=0 send_seq=21290 receive_seq=21290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000077 adj=63997602 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=43591 bytes_read=1788359 bytes_retransmit=9 bytes_invalid=0 send_seq=7206 receive_seq=7206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44077 bytes_read=132755 bytes_retransmit=9 bytes_invalid=0 send_seq=7193 receive_seq=7193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98169 bytes_read=2718805 bytes_retransmit=0 bytes_invalid=0 send_seq=11752 receive_seq=11752 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998644 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.3 th2: temp=61.8 th3: temp=59.3 sysload=0.23 cputime=549.404 memavail=7395272 print_time=7027.870 buffer_time=2.208 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 87 Hz
Stats 7004.0: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34217223 bytes_read=5240621 bytes_retransmit=9 bytes_invalid=0 send_seq=643602 receive_seq=643602 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=15141 freq=400015951 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43330 bytes_read=135433 bytes_retransmit=0 bytes_invalid=0 send_seq=7193 receive_seq=7193 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999380 adj=49997404 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213980 bytes_read=6940265 bytes_retransmit=9 bytes_invalid=0 send_seq=29937 receive_seq=29937 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997648 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152884 bytes_read=4356670 bytes_retransmit=9 bytes_invalid=0 send_seq=21301 receive_seq=21301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000074 adj=63997554 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=43597 bytes_read=1788593 bytes_retransmit=9 bytes_invalid=0 send_seq=7207 receive_seq=7207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44083 bytes_read=132771 bytes_retransmit=9 bytes_invalid=0 send_seq=7194 receive_seq=7194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98175 bytes_read=2719161 bytes_retransmit=0 bytes_invalid=0 send_seq=11753 receive_seq=11753 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998654 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.5 th2: temp=61.8 th3: temp=59.3 sysload=0.23 cputime=549.535 memavail=7395272 print_time=7028.734 buffer_time=2.071 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 7005.0: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34228846 bytes_read=5241946 bytes_retransmit=9 bytes_invalid=0 send_seq=643805 receive_seq=643805 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=16793 freq=400015927 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43336 bytes_read=135449 bytes_retransmit=0 bytes_invalid=0 send_seq=7194 receive_seq=7194 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999379 adj=49997418 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213986 bytes_read=6940379 bytes_retransmit=9 bytes_invalid=0 send_seq=29938 receive_seq=29938 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997681 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=152960 bytes_read=4359726 bytes_retransmit=9 bytes_invalid=0 send_seq=21312 receive_seq=21312 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000072 adj=63997540 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43603 bytes_read=1788902 bytes_retransmit=9 bytes_invalid=0 send_seq=7208 receive_seq=7208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44089 bytes_read=132787 bytes_retransmit=9 bytes_invalid=0 send_seq=7195 receive_seq=7195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98181 bytes_read=2719517 bytes_retransmit=0 bytes_invalid=0 send_seq=11754 receive_seq=11754 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998662 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.2 th1: temp=56.5 th2: temp=61.8 th3: temp=59.2 sysload=0.23 cputime=549.663 memavail=7395288 print_time=7029.674 buffer_time=2.009 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 88 Hz
Testing frequency 89 Hz
Stats 7006.0: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34243058 bytes_read=5243530 bytes_retransmit=9 bytes_invalid=0 send_seq=644054 receive_seq=644054 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=18456 freq=400015939 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43342 bytes_read=135465 bytes_retransmit=0 bytes_invalid=0 send_seq=7195 receive_seq=7195 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999378 adj=49997442 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213992 bytes_read=6940479 bytes_retransmit=9 bytes_invalid=0 send_seq=29939 receive_seq=29939 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997728 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153036 bytes_read=4362841 bytes_retransmit=9 bytes_invalid=0 send_seq=21323 receive_seq=21323 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997562 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43609 bytes_read=1789136 bytes_retransmit=9 bytes_invalid=0 send_seq=7209 receive_seq=7209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997700 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44095 bytes_read=132803 bytes_retransmit=9 bytes_invalid=0 send_seq=7196 receive_seq=7196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98187 bytes_read=2719873 bytes_retransmit=0 bytes_invalid=0 send_seq=11755 receive_seq=11755 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998696 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.5 th2: temp=61.7 th3: temp=59.3 sysload=0.21 cputime=549.815 memavail=7392016 print_time=7030.872 buffer_time=2.203 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 90 Hz
Stats 7007.0: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34257620 bytes_read=5245105 bytes_retransmit=9 bytes_invalid=0 send_seq=644307 receive_seq=644307 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=15340 freq=400015927 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43348 bytes_read=135481 bytes_retransmit=0 bytes_invalid=0 send_seq=7196 receive_seq=7196 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999377 adj=49997395 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=213998 bytes_read=6940607 bytes_retransmit=9 bytes_invalid=0 send_seq=29940 receive_seq=29940 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997676 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153112 bytes_read=4365928 bytes_retransmit=9 bytes_invalid=0 send_seq=21334 receive_seq=21334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43615 bytes_read=1789370 bytes_retransmit=9 bytes_invalid=0 send_seq=7210 receive_seq=7210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997669 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44101 bytes_read=132830 bytes_retransmit=9 bytes_invalid=0 send_seq=7197 receive_seq=7197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98193 bytes_read=2720229 bytes_retransmit=0 bytes_invalid=0 send_seq=11756 receive_seq=11756 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998690 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.5 th2: temp=61.7 th3: temp=59.2 sysload=0.21 cputime=549.964 memavail=7393792 print_time=7031.751 buffer_time=2.081 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 7008.0: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34269185 bytes_read=5246441 bytes_retransmit=9 bytes_invalid=0 send_seq=644509 receive_seq=644509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=16987 freq=400015927 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43354 bytes_read=135510 bytes_retransmit=0 bytes_invalid=0 send_seq=7197 receive_seq=7197 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999377 adj=49997405 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214004 bytes_read=6940707 bytes_retransmit=9 bytes_invalid=0 send_seq=29941 receive_seq=29941 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997689 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153188 bytes_read=4369003 bytes_retransmit=9 bytes_invalid=0 send_seq=21345 receive_seq=21345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997494 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43621 bytes_read=1789664 bytes_retransmit=9 bytes_invalid=0 send_seq=7211 receive_seq=7211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997686 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44107 bytes_read=132846 bytes_retransmit=9 bytes_invalid=0 send_seq=7198 receive_seq=7198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98199 bytes_read=2720585 bytes_retransmit=0 bytes_invalid=0 send_seq=11757 receive_seq=11757 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998698 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.6 th2: temp=61.8 th3: temp=59.3 sysload=0.21 cputime=550.094 memavail=7392572 print_time=7032.680 buffer_time=2.008 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 91 Hz
Testing frequency 92 Hz
Stats 7009.0: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34283636 bytes_read=5248040 bytes_retransmit=9 bytes_invalid=0 send_seq=644761 receive_seq=644761 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=21 upcoming_bytes=18886 freq=400015946 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43360 bytes_read=135526 bytes_retransmit=0 bytes_invalid=0 send_seq=7198 receive_seq=7198 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999376 adj=49997399 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214010 bytes_read=6940807 bytes_retransmit=9 bytes_invalid=0 send_seq=29942 receive_seq=29942 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997690 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153264 bytes_read=4372061 bytes_retransmit=9 bytes_invalid=0 send_seq=21356 receive_seq=21356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997463 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43627 bytes_read=1789898 bytes_retransmit=9 bytes_invalid=0 send_seq=7212 receive_seq=7212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44113 bytes_read=132862 bytes_retransmit=9 bytes_invalid=0 send_seq=7199 receive_seq=7199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98205 bytes_read=2720941 bytes_retransmit=0 bytes_invalid=0 send_seq=11758 receive_seq=11758 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998684 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.4 th2: temp=61.8 th3: temp=59.3 sysload=0.21 cputime=550.245 memavail=7392348 print_time=7033.889 buffer_time=2.215 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 93 Hz
Stats 7010.0: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34298086 bytes_read=5249609 bytes_retransmit=9 bytes_invalid=0 send_seq=645013 receive_seq=645013 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=15684 freq=400015938 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43366 bytes_read=135542 bytes_retransmit=0 bytes_invalid=0 send_seq=7199 receive_seq=7199 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999378 adj=49997360 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214016 bytes_read=6940949 bytes_retransmit=9 bytes_invalid=0 send_seq=29943 receive_seq=29943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997637 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153340 bytes_read=4375146 bytes_retransmit=9 bytes_invalid=0 send_seq=21367 receive_seq=21367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000072 adj=63997419 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=43633 bytes_read=1790147 bytes_retransmit=9 bytes_invalid=0 send_seq=7213 receive_seq=7213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44119 bytes_read=132878 bytes_retransmit=9 bytes_invalid=0 send_seq=7200 receive_seq=7200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98211 bytes_read=2721297 bytes_retransmit=0 bytes_invalid=0 send_seq=11759 receive_seq=11759 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998651 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=57.2 th1: temp=56.3 th2: temp=61.8 th3: temp=59.4 sysload=0.21 cputime=550.376 memavail=7392348 print_time=7034.759 buffer_time=2.084 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 7011.0: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34309989 bytes_read=5250954 bytes_retransmit=9 bytes_invalid=0 send_seq=645221 receive_seq=645221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=17495 freq=400015992 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43372 bytes_read=135558 bytes_retransmit=0 bytes_invalid=0 send_seq=7200 receive_seq=7200 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999377 adj=49997395 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214022 bytes_read=6941049 bytes_retransmit=9 bytes_invalid=0 send_seq=29944 receive_seq=29944 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997670 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153416 bytes_read=4378203 bytes_retransmit=9 bytes_invalid=0 send_seq=21378 receive_seq=21378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997561 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=43639 bytes_read=1790441 bytes_retransmit=9 bytes_invalid=0 send_seq=7214 receive_seq=7214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44125 bytes_read=132894 bytes_retransmit=9 bytes_invalid=0 send_seq=7201 receive_seq=7201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98217 bytes_read=2721653 bytes_retransmit=0 bytes_invalid=0 send_seq=11760 receive_seq=11760 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998681 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.7 th2: temp=61.8 th3: temp=59.3 sysload=0.27 cputime=550.506 memavail=7392608 print_time=7035.690 buffer_time=2.015 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 94 Hz
Testing frequency 95 Hz
Stats 7012.0: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34324327 bytes_read=5252548 bytes_retransmit=9 bytes_invalid=0 send_seq=645472 receive_seq=645472 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=19812 freq=400015995 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43378 bytes_read=135574 bytes_retransmit=0 bytes_invalid=0 send_seq=7201 receive_seq=7201 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999376 adj=49997291 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214028 bytes_read=6941149 bytes_retransmit=9 bytes_invalid=0 send_seq=29945 receive_seq=29945 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997544 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153492 bytes_read=4381318 bytes_retransmit=9 bytes_invalid=0 send_seq=21389 receive_seq=21389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997405 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=43645 bytes_read=1790675 bytes_retransmit=9 bytes_invalid=0 send_seq=7215 receive_seq=7215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997566 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44131 bytes_read=132921 bytes_retransmit=9 bytes_invalid=0 send_seq=7202 receive_seq=7202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999418 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98223 bytes_read=2722009 bytes_retransmit=0 bytes_invalid=0 send_seq=11761 receive_seq=11761 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998618 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=57.2 th1: temp=56.5 th2: temp=61.8 th3: temp=59.3 sysload=0.27 cputime=550.657 memavail=7392608 print_time=7036.895 buffer_time=2.220 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 96 Hz
Stats 7013.0: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34339194 bytes_read=5254154 bytes_retransmit=9 bytes_invalid=0 send_seq=645728 receive_seq=645728 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=16492 freq=400015981 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43384 bytes_read=135603 bytes_retransmit=0 bytes_invalid=0 send_seq=7202 receive_seq=7202 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999374 adj=49997300 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214034 bytes_read=6941277 bytes_retransmit=9 bytes_invalid=0 send_seq=29946 receive_seq=29946 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997566 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153568 bytes_read=4384421 bytes_retransmit=9 bytes_invalid=0 send_seq=21400 receive_seq=21400 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997410 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=43651 bytes_read=1790909 bytes_retransmit=9 bytes_invalid=0 send_seq=7216 receive_seq=7216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997580 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44137 bytes_read=132937 bytes_retransmit=9 bytes_invalid=0 send_seq=7203 receive_seq=7203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999421 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98229 bytes_read=2722365 bytes_retransmit=0 bytes_invalid=0 send_seq=11762 receive_seq=11762 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998631 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.6 th2: temp=61.9 th3: temp=59.3 sysload=0.27 cputime=550.799 memavail=7389100 print_time=7037.766 buffer_time=2.090 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 7014.0: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34351418 bytes_read=5255529 bytes_retransmit=9 bytes_invalid=0 send_seq=645941 receive_seq=645941 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=51 upcoming_bytes=18208 freq=400015962 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43390 bytes_read=135619 bytes_retransmit=0 bytes_invalid=0 send_seq=7203 receive_seq=7203 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999376 adj=49997314 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214040 bytes_read=6941377 bytes_retransmit=9 bytes_invalid=0 send_seq=29947 receive_seq=29947 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63997652 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153644 bytes_read=4387480 bytes_retransmit=9 bytes_invalid=0 send_seq=21411 receive_seq=21411 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997417 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=43657 bytes_read=1791203 bytes_retransmit=9 bytes_invalid=0 send_seq=7217 receive_seq=7217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997602 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44143 bytes_read=132953 bytes_retransmit=9 bytes_invalid=0 send_seq=7204 receive_seq=7204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98235 bytes_read=2722721 bytes_retransmit=0 bytes_invalid=0 send_seq=11763 receive_seq=11763 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998642 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.5 th2: temp=61.8 th3: temp=59.3 sysload=0.27 cputime=550.938 memavail=7393468 print_time=7038.694 buffer_time=2.017 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 97 Hz
Testing frequency 98 Hz
Stats 7015.0: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34366301 bytes_read=5257143 bytes_retransmit=9 bytes_invalid=0 send_seq=646196 receive_seq=646196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=20282 freq=400015997 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43396 bytes_read=135635 bytes_retransmit=0 bytes_invalid=0 send_seq=7204 receive_seq=7204 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999375 adj=49997376 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214046 bytes_read=6941491 bytes_retransmit=9 bytes_invalid=0 send_seq=29948 receive_seq=29948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997680 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153720 bytes_read=4390539 bytes_retransmit=9 bytes_invalid=0 send_seq=21422 receive_seq=21422 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997444 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43663 bytes_read=1791452 bytes_retransmit=9 bytes_invalid=0 send_seq=7218 receive_seq=7218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44149 bytes_read=132969 bytes_retransmit=9 bytes_invalid=0 send_seq=7205 receive_seq=7205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999438 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98241 bytes_read=2723077 bytes_retransmit=0 bytes_invalid=0 send_seq=11764 receive_seq=11764 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998693 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.4 th2: temp=61.8 th3: temp=59.3 sysload=0.27 cputime=551.092 memavail=7393468 print_time=7039.898 buffer_time=2.220 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 99 Hz
Stats 7016.0: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34381324 bytes_read=5258743 bytes_retransmit=9 bytes_invalid=0 send_seq=646454 receive_seq=646454 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=53 upcoming_bytes=16851 freq=400016017 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43402 bytes_read=135651 bytes_retransmit=0 bytes_invalid=0 send_seq=7205 receive_seq=7205 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999374 adj=49997312 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214052 bytes_read=6941619 bytes_retransmit=9 bytes_invalid=0 send_seq=29949 receive_seq=29949 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63997603 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153789 bytes_read=4393600 bytes_retransmit=9 bytes_invalid=0 send_seq=21432 receive_seq=21432 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997374 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43669 bytes_read=1791701 bytes_retransmit=9 bytes_invalid=0 send_seq=7219 receive_seq=7219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997618 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44155 bytes_read=132985 bytes_retransmit=9 bytes_invalid=0 send_seq=7206 receive_seq=7206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98247 bytes_read=2723433 bytes_retransmit=0 bytes_invalid=0 send_seq=11765 receive_seq=11765 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998693 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.4 th2: temp=61.8 th3: temp=59.3 sysload=0.25 cputime=551.231 memavail=7393468 print_time=7040.771 buffer_time=2.091 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7017.0: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34393821 bytes_read=5260143 bytes_retransmit=9 bytes_invalid=0 send_seq=646672 receive_seq=646672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=18692 freq=400016020 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43408 bytes_read=135667 bytes_retransmit=0 bytes_invalid=0 send_seq=7206 receive_seq=7206 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999374 adj=49997273 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214058 bytes_read=6941719 bytes_retransmit=9 bytes_invalid=0 send_seq=29950 receive_seq=29950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997555 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153865 bytes_read=4396656 bytes_retransmit=9 bytes_invalid=0 send_seq=21443 receive_seq=21443 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997320 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43675 bytes_read=1791980 bytes_retransmit=9 bytes_invalid=0 send_seq=7220 receive_seq=7220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997593 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44161 bytes_read=133012 bytes_retransmit=9 bytes_invalid=0 send_seq=7207 receive_seq=7207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999418 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98253 bytes_read=2723789 bytes_retransmit=0 bytes_invalid=0 send_seq=11766 receive_seq=11766 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998657 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.4 th1: temp=56.5 th2: temp=61.9 th3: temp=59.3 sysload=0.25 cputime=551.364 memavail=7393468 print_time=7041.703 buffer_time=2.023 print_stall=0 extruder: target=0 temp=18.5 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 100 Hz
Testing frequency 101 Hz
Stats 7018.0: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34408910 bytes_read=5261793 bytes_retransmit=9 bytes_invalid=0 send_seq=646931 receive_seq=646931 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=30 upcoming_bytes=20667 freq=400016008 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43414 bytes_read=135696 bytes_retransmit=0 bytes_invalid=0 send_seq=7207 receive_seq=7207 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999373 adj=49997279 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214064 bytes_read=6941819 bytes_retransmit=9 bytes_invalid=0 send_seq=29951 receive_seq=29951 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63997555 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=153941 bytes_read=4399729 bytes_retransmit=9 bytes_invalid=0 send_seq=21454 receive_seq=21454 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997332 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43681 bytes_read=1792214 bytes_retransmit=9 bytes_invalid=0 send_seq=7221 receive_seq=7221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997590 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44167 bytes_read=133028 bytes_retransmit=9 bytes_invalid=0 send_seq=7208 receive_seq=7208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999418 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98259 bytes_read=2724145 bytes_retransmit=0 bytes_invalid=0 send_seq=11767 receive_seq=11767 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998641 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.5 th2: temp=61.7 th3: temp=59.5 sysload=0.25 cputime=551.521 memavail=7394024 print_time=7042.906 buffer_time=2.226 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 102 Hz
Stats 7019.0: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34424304 bytes_read=5263428 bytes_retransmit=9 bytes_invalid=0 send_seq=647197 receive_seq=647196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=24 upcoming_bytes=17040 freq=400015996 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43420 bytes_read=135712 bytes_retransmit=0 bytes_invalid=0 send_seq=7208 receive_seq=7208 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999373 adj=49997324 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214070 bytes_read=6941947 bytes_retransmit=9 bytes_invalid=0 send_seq=29952 receive_seq=29952 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997597 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154017 bytes_read=4402873 bytes_retransmit=9 bytes_invalid=0 send_seq=21465 receive_seq=21465 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997387 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43687 bytes_read=1792463 bytes_retransmit=9 bytes_invalid=0 send_seq=7222 receive_seq=7222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44173 bytes_read=133044 bytes_retransmit=9 bytes_invalid=0 send_seq=7209 receive_seq=7209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999427 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98265 bytes_read=2724501 bytes_retransmit=0 bytes_invalid=0 send_seq=11768 receive_seq=11768 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998652 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.5 th2: temp=61.8 th3: temp=59.3 sysload=0.25 cputime=551.662 memavail=7394064 print_time=7043.777 buffer_time=2.097 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7020.0: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34436616 bytes_read=5264828 bytes_retransmit=9 bytes_invalid=0 send_seq=647414 receive_seq=647414 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=19260 freq=400015978 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43426 bytes_read=135728 bytes_retransmit=0 bytes_invalid=0 send_seq=7209 receive_seq=7209 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999371 adj=49997338 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214076 bytes_read=6942047 bytes_retransmit=9 bytes_invalid=0 send_seq=29953 receive_seq=29953 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997629 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154093 bytes_read=4405933 bytes_retransmit=9 bytes_invalid=0 send_seq=21476 receive_seq=21476 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997403 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43693 bytes_read=1792757 bytes_retransmit=9 bytes_invalid=0 send_seq=7223 receive_seq=7223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44179 bytes_read=133060 bytes_retransmit=9 bytes_invalid=0 send_seq=7210 receive_seq=7210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98271 bytes_read=2724857 bytes_retransmit=0 bytes_invalid=0 send_seq=11769 receive_seq=11769 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998662 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.5 th2: temp=61.7 th3: temp=59.3 sysload=0.25 cputime=551.798 memavail=7393840 print_time=7044.704 buffer_time=2.024 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 103 Hz
Testing frequency 104 Hz
Stats 7021.0: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34452019 bytes_read=5266488 bytes_retransmit=9 bytes_invalid=0 send_seq=647679 receive_seq=647679 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=21447 freq=400015962 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43432 bytes_read=135744 bytes_retransmit=0 bytes_invalid=0 send_seq=7210 receive_seq=7210 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999371 adj=49997357 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214082 bytes_read=6942161 bytes_retransmit=9 bytes_invalid=0 send_seq=29954 receive_seq=29954 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997743 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154169 bytes_read=4408991 bytes_retransmit=9 bytes_invalid=0 send_seq=21487 receive_seq=21487 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997447 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43699 bytes_read=1792991 bytes_retransmit=9 bytes_invalid=0 send_seq=7224 receive_seq=7224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997694 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44185 bytes_read=133076 bytes_retransmit=9 bytes_invalid=0 send_seq=7211 receive_seq=7211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98277 bytes_read=2725213 bytes_retransmit=0 bytes_invalid=0 send_seq=11770 receive_seq=11770 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998686 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=57.2 th1: temp=56.3 th2: temp=61.7 th3: temp=59.3 sysload=0.23 cputime=551.957 memavail=7393840 print_time=7045.909 buffer_time=2.228 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 105 Hz
Stats 7022.0: gcodein=0  mcu: mcu_awake=0.012 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34467583 bytes_read=5268142 bytes_retransmit=9 bytes_invalid=0 send_seq=647948 receive_seq=647948 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=17886 freq=400015947 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43438 bytes_read=135760 bytes_retransmit=0 bytes_invalid=0 send_seq=7211 receive_seq=7211 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999372 adj=49997385 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214088 bytes_read=6942289 bytes_retransmit=9 bytes_invalid=0 send_seq=29955 receive_seq=29955 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997749 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154245 bytes_read=4412077 bytes_retransmit=9 bytes_invalid=0 send_seq=21498 receive_seq=21498 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997480 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43705 bytes_read=1793240 bytes_retransmit=9 bytes_invalid=0 send_seq=7225 receive_seq=7225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997692 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44191 bytes_read=133103 bytes_retransmit=9 bytes_invalid=0 send_seq=7212 receive_seq=7212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999454 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98283 bytes_read=2725569 bytes_retransmit=0 bytes_invalid=0 send_seq=11771 receive_seq=11771 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998689 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.6 th2: temp=61.7 th3: temp=59.3 sysload=0.23 cputime=552.100 memavail=7393840 print_time=7046.783 buffer_time=2.102 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 7023.0: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34480463 bytes_read=5269588 bytes_retransmit=9 bytes_invalid=0 send_seq=648172 receive_seq=648172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=19894 freq=400015928 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=43444 bytes_read=135789 bytes_retransmit=0 bytes_invalid=0 send_seq=7212 receive_seq=7212 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999372 adj=49997412 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214094 bytes_read=6942385 bytes_retransmit=9 bytes_invalid=0 send_seq=29956 receive_seq=29956 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997963 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154321 bytes_read=4415142 bytes_retransmit=9 bytes_invalid=0 send_seq=21509 receive_seq=21509 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997504 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43711 bytes_read=1793519 bytes_retransmit=9 bytes_invalid=0 send_seq=7226 receive_seq=7226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997704 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44197 bytes_read=133119 bytes_retransmit=9 bytes_invalid=0 send_seq=7213 receive_seq=7213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98289 bytes_read=2725925 bytes_retransmit=0 bytes_invalid=0 send_seq=11772 receive_seq=11772 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998697 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=57.2 th1: temp=56.5 th2: temp=62.0 th3: temp=59.5 sysload=0.23 cputime=552.237 memavail=7393840 print_time=7047.715 buffer_time=2.033 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 106 Hz
Testing frequency 107 Hz
Stats 7024.0: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34496112 bytes_read=5271267 bytes_retransmit=9 bytes_invalid=0 send_seq=648440 receive_seq=648440 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=14 upcoming_bytes=21994 freq=400015919 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=43450 bytes_read=135805 bytes_retransmit=0 bytes_invalid=0 send_seq=7213 receive_seq=7213 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999372 adj=49997440 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214100 bytes_read=6942478 bytes_retransmit=9 bytes_invalid=0 send_seq=29957 receive_seq=29957 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997936 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154397 bytes_read=4418183 bytes_retransmit=9 bytes_invalid=0 send_seq=21520 receive_seq=21520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997526 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43717 bytes_read=1793753 bytes_retransmit=9 bytes_invalid=0 send_seq=7227 receive_seq=7227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997729 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44203 bytes_read=133135 bytes_retransmit=9 bytes_invalid=0 send_seq=7214 receive_seq=7214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999462 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98295 bytes_read=2726281 bytes_retransmit=0 bytes_invalid=0 send_seq=11773 receive_seq=11773 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998709 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.6 th2: temp=61.6 th3: temp=59.4 sysload=0.23 cputime=552.397 memavail=7393840 print_time=7048.911 buffer_time=2.229 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 108 Hz
Stats 7025.0: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34512038 bytes_read=5272952 bytes_retransmit=9 bytes_invalid=0 send_seq=648715 receive_seq=648715 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=18303 freq=400015897 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=43456 bytes_read=135821 bytes_retransmit=0 bytes_invalid=0 send_seq=7214 receive_seq=7214 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999371 adj=49997432 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214106 bytes_read=6942597 bytes_retransmit=9 bytes_invalid=0 send_seq=29958 receive_seq=29958 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997855 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154473 bytes_read=4421248 bytes_retransmit=9 bytes_invalid=0 send_seq=21531 receive_seq=21531 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997530 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43723 bytes_read=1794017 bytes_retransmit=9 bytes_invalid=0 send_seq=7228 receive_seq=7228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997709 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44209 bytes_read=133151 bytes_retransmit=9 bytes_invalid=0 send_seq=7215 receive_seq=7215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999470 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98301 bytes_read=2726637 bytes_retransmit=0 bytes_invalid=0 send_seq=11774 receive_seq=11774 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998709 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.5 th2: temp=61.9 th3: temp=59.4 sysload=0.23 cputime=552.540 memavail=7393840 print_time=7049.787 buffer_time=2.105 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 7026.0: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34525169 bytes_read=5274402 bytes_retransmit=9 bytes_invalid=0 send_seq=648943 receive_seq=648943 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=20424 freq=400015890 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=43462 bytes_read=135837 bytes_retransmit=0 bytes_invalid=0 send_seq=7215 receive_seq=7215 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999369 adj=49997438 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214112 bytes_read=6942704 bytes_retransmit=9 bytes_invalid=0 send_seq=29959 receive_seq=29959 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997842 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154549 bytes_read=4424288 bytes_retransmit=9 bytes_invalid=0 send_seq=21542 receive_seq=21542 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997563 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43729 bytes_read=1794296 bytes_retransmit=9 bytes_invalid=0 send_seq=7229 receive_seq=7229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997718 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44215 bytes_read=133167 bytes_retransmit=9 bytes_invalid=0 send_seq=7216 receive_seq=7216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999470 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98307 bytes_read=2726993 bytes_retransmit=0 bytes_invalid=0 send_seq=11775 receive_seq=11775 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998715 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.3 th2: temp=61.9 th3: temp=59.3 sysload=0.29 cputime=552.679 memavail=7393376 print_time=7050.718 buffer_time=2.035 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 109 Hz
Testing frequency 110 Hz
Stats 7027.0: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34540984 bytes_read=5276091 bytes_retransmit=9 bytes_invalid=0 send_seq=649213 receive_seq=649213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=38 upcoming_bytes=22596 freq=400015879 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=43468 bytes_read=135853 bytes_retransmit=0 bytes_invalid=0 send_seq=7216 receive_seq=7216 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999369 adj=49997427 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214118 bytes_read=6942799 bytes_retransmit=9 bytes_invalid=0 send_seq=29960 receive_seq=29960 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997815 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154618 bytes_read=4427369 bytes_retransmit=9 bytes_invalid=0 send_seq=21552 receive_seq=21552 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997568 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43735 bytes_read=1794530 bytes_retransmit=9 bytes_invalid=0 send_seq=7230 receive_seq=7230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997711 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44221 bytes_read=133194 bytes_retransmit=9 bytes_invalid=0 send_seq=7217 receive_seq=7217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999467 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98313 bytes_read=2727349 bytes_retransmit=0 bytes_invalid=0 send_seq=11776 receive_seq=11776 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998705 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.5 th2: temp=61.9 th3: temp=59.3 sysload=0.29 cputime=552.839 memavail=7393376 print_time=7051.918 buffer_time=2.235 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 111 Hz
Stats 7028.0: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34557233 bytes_read=5277817 bytes_retransmit=9 bytes_invalid=0 send_seq=649493 receive_seq=649493 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=29 upcoming_bytes=18731 freq=400015868 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43474 bytes_read=135882 bytes_retransmit=0 bytes_invalid=0 send_seq=7217 receive_seq=7217 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999369 adj=49997422 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214124 bytes_read=6942927 bytes_retransmit=9 bytes_invalid=0 send_seq=29961 receive_seq=29961 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997776 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154694 bytes_read=4430471 bytes_retransmit=9 bytes_invalid=0 send_seq=21563 receive_seq=21563 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997569 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43741 bytes_read=1794779 bytes_retransmit=9 bytes_invalid=0 send_seq=7231 receive_seq=7231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997768 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44227 bytes_read=133210 bytes_retransmit=9 bytes_invalid=0 send_seq=7218 receive_seq=7218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98319 bytes_read=2727705 bytes_retransmit=0 bytes_invalid=0 send_seq=11777 receive_seq=11777 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998695 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.5 th2: temp=61.9 th3: temp=59.4 sysload=0.29 cputime=552.986 memavail=7393388 print_time=7052.793 buffer_time=2.110 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7029.0: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34570270 bytes_read=5279257 bytes_retransmit=9 bytes_invalid=0 send_seq=649719 receive_seq=649719 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=21000 freq=400015873 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43480 bytes_read=135898 bytes_retransmit=0 bytes_invalid=0 send_seq=7218 receive_seq=7218 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999370 adj=49997439 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214130 bytes_read=6943027 bytes_retransmit=9 bytes_invalid=0 send_seq=29962 receive_seq=29962 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997797 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154770 bytes_read=4433529 bytes_retransmit=9 bytes_invalid=0 send_seq=21574 receive_seq=21574 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997575 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43747 bytes_read=1795058 bytes_retransmit=9 bytes_invalid=0 send_seq=7232 receive_seq=7232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997761 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44233 bytes_read=133226 bytes_retransmit=9 bytes_invalid=0 send_seq=7219 receive_seq=7219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98325 bytes_read=2728061 bytes_retransmit=0 bytes_invalid=0 send_seq=11778 receive_seq=11778 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998702 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.6 th2: temp=62.0 th3: temp=59.3 sysload=0.29 cputime=553.124 memavail=7393388 print_time=7053.719 buffer_time=2.035 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 112 Hz
Testing frequency 113 Hz
Stats 7030.0: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34586683 bytes_read=5281006 bytes_retransmit=9 bytes_invalid=0 send_seq=650001 receive_seq=650001 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=22763 freq=400015903 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43486 bytes_read=135914 bytes_retransmit=0 bytes_invalid=0 send_seq=7219 receive_seq=7219 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999369 adj=49997438 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214136 bytes_read=6943127 bytes_retransmit=9 bytes_invalid=0 send_seq=29963 receive_seq=29963 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997755 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154846 bytes_read=4436587 bytes_retransmit=9 bytes_invalid=0 send_seq=21585 receive_seq=21585 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997646 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43753 bytes_read=1795307 bytes_retransmit=9 bytes_invalid=0 send_seq=7233 receive_seq=7233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997740 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44239 bytes_read=133242 bytes_retransmit=9 bytes_invalid=0 send_seq=7220 receive_seq=7220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98331 bytes_read=2728417 bytes_retransmit=0 bytes_invalid=0 send_seq=11779 receive_seq=11779 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998682 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.5 th2: temp=62.0 th3: temp=59.4 sysload=0.29 cputime=553.285 memavail=7393388 print_time=7054.927 buffer_time=2.243 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 114 Hz
Stats 7031.0: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34603051 bytes_read=5282741 bytes_retransmit=9 bytes_invalid=0 send_seq=650286 receive_seq=650286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=18832 freq=400015904 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43492 bytes_read=135930 bytes_retransmit=0 bytes_invalid=0 send_seq=7220 receive_seq=7220 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999369 adj=49997366 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214142 bytes_read=6943269 bytes_retransmit=9 bytes_invalid=0 send_seq=29964 receive_seq=29964 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997658 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154922 bytes_read=4439674 bytes_retransmit=9 bytes_invalid=0 send_seq=21596 receive_seq=21596 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997545 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43759 bytes_read=1795556 bytes_retransmit=9 bytes_invalid=0 send_seq=7234 receive_seq=7234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44245 bytes_read=133258 bytes_retransmit=9 bytes_invalid=0 send_seq=7221 receive_seq=7221 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98337 bytes_read=2728773 bytes_retransmit=0 bytes_invalid=0 send_seq=11780 receive_seq=11780 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998650 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.4 th2: temp=61.7 th3: temp=59.3 sysload=0.27 cputime=553.445 memavail=7393764 print_time=7055.796 buffer_time=2.112 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.5 pwm=0.000
Stats 7032.0: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34616176 bytes_read=5284197 bytes_retransmit=9 bytes_invalid=0 send_seq=650516 receive_seq=650516 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=52 upcoming_bytes=21428 freq=400015888 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43498 bytes_read=135946 bytes_retransmit=0 bytes_invalid=0 send_seq=7221 receive_seq=7221 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999368 adj=49997367 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214148 bytes_read=6943369 bytes_retransmit=9 bytes_invalid=0 send_seq=29965 receive_seq=29965 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997730 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=154998 bytes_read=4442731 bytes_retransmit=9 bytes_invalid=0 send_seq=21607 receive_seq=21607 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997592 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43765 bytes_read=1795835 bytes_retransmit=9 bytes_invalid=0 send_seq=7235 receive_seq=7235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44251 bytes_read=133285 bytes_retransmit=9 bytes_invalid=0 send_seq=7222 receive_seq=7222 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98343 bytes_read=2729129 bytes_retransmit=0 bytes_invalid=0 send_seq=11781 receive_seq=11781 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998650 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.3 th1: temp=56.5 th2: temp=61.9 th3: temp=59.3 sysload=0.27 cputime=553.584 memavail=7393764 print_time=7056.728 buffer_time=2.044 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 115 Hz
Testing frequency 116 Hz
Stats 7033.0: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34632529 bytes_read=5285942 bytes_retransmit=9 bytes_invalid=0 send_seq=650794 receive_seq=650794 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=37 upcoming_bytes=23751 freq=400015894 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43504 bytes_read=135975 bytes_retransmit=0 bytes_invalid=0 send_seq=7222 receive_seq=7222 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999368 adj=49997383 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214154 bytes_read=6943469 bytes_retransmit=9 bytes_invalid=0 send_seq=29966 receive_seq=29966 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997733 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155074 bytes_read=4445804 bytes_retransmit=9 bytes_invalid=0 send_seq=21618 receive_seq=21618 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000074 adj=63997605 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43771 bytes_read=1796069 bytes_retransmit=9 bytes_invalid=0 send_seq=7236 receive_seq=7236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997675 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44257 bytes_read=133301 bytes_retransmit=9 bytes_invalid=0 send_seq=7223 receive_seq=7223 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98349 bytes_read=2729485 bytes_retransmit=0 bytes_invalid=0 send_seq=11782 receive_seq=11782 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998667 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.4 th2: temp=61.9 th3: temp=59.4 sysload=0.27 cputime=553.747 memavail=7393768 print_time=7057.930 buffer_time=2.246 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.4 pwm=0.000
Testing frequency 117 Hz
Stats 7034.0: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34649297 bytes_read=5287697 bytes_retransmit=9 bytes_invalid=0 send_seq=651083 receive_seq=651083 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=56 upcoming_bytes=19508 freq=400015897 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43510 bytes_read=135991 bytes_retransmit=0 bytes_invalid=0 send_seq=7223 receive_seq=7223 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999371 adj=49997374 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214160 bytes_read=6943597 bytes_retransmit=9 bytes_invalid=0 send_seq=29967 receive_seq=29967 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997688 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155150 bytes_read=4448888 bytes_retransmit=9 bytes_invalid=0 send_seq=21629 receive_seq=21629 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000072 adj=63997726 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43777 bytes_read=1796318 bytes_retransmit=9 bytes_invalid=0 send_seq=7237 receive_seq=7237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44263 bytes_read=133317 bytes_retransmit=9 bytes_invalid=0 send_seq=7224 receive_seq=7224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98355 bytes_read=2729841 bytes_retransmit=0 bytes_invalid=0 send_seq=11783 receive_seq=11783 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998657 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.5 th2: temp=61.8 th3: temp=59.4 sysload=0.27 cputime=553.897 memavail=7393768 print_time=7058.797 buffer_time=2.112 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7035.0: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34662876 bytes_read=5289187 bytes_retransmit=9 bytes_invalid=0 send_seq=651319 receive_seq=651319 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=21828 freq=400015887 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43516 bytes_read=136007 bytes_retransmit=0 bytes_invalid=0 send_seq=7224 receive_seq=7224 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999371 adj=49997397 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214166 bytes_read=6943697 bytes_retransmit=9 bytes_invalid=0 send_seq=29968 receive_seq=29968 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997671 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155226 bytes_read=4452004 bytes_retransmit=9 bytes_invalid=0 send_seq=21640 receive_seq=21640 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997677 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43783 bytes_read=1796612 bytes_retransmit=9 bytes_invalid=0 send_seq=7238 receive_seq=7238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44269 bytes_read=133333 bytes_retransmit=9 bytes_invalid=0 send_seq=7225 receive_seq=7225 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98361 bytes_read=2730197 bytes_retransmit=0 bytes_invalid=0 send_seq=11784 receive_seq=11784 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998651 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.5 th2: temp=61.8 th3: temp=59.4 sysload=0.27 cputime=554.041 memavail=7393776 print_time=7059.735 buffer_time=2.050 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 118 Hz
Testing frequency 119 Hz
Stats 7036.0: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34679631 bytes_read=5290961 bytes_retransmit=9 bytes_invalid=0 send_seq=651606 receive_seq=651606 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=31 upcoming_bytes=23820 freq=400015874 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43522 bytes_read=136023 bytes_retransmit=0 bytes_invalid=0 send_seq=7225 receive_seq=7225 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999372 adj=49997423 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214172 bytes_read=6943811 bytes_retransmit=9 bytes_invalid=0 send_seq=29969 receive_seq=29969 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000241 adj=63997799 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155302 bytes_read=4455060 bytes_retransmit=9 bytes_invalid=0 send_seq=21651 receive_seq=21651 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997644 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43789 bytes_read=1796846 bytes_retransmit=9 bytes_invalid=0 send_seq=7239 receive_seq=7239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44275 bytes_read=133349 bytes_retransmit=9 bytes_invalid=0 send_seq=7226 receive_seq=7226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999441 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98367 bytes_read=2730553 bytes_retransmit=0 bytes_invalid=0 send_seq=11785 receive_seq=11785 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998655 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=57.2 th1: temp=56.6 th2: temp=61.8 th3: temp=59.4 sysload=0.25 cputime=554.210 memavail=7393776 print_time=7060.934 buffer_time=2.249 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 120 Hz
Stats 7037.0: gcodein=0  mcu: mcu_awake=0.013 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34696364 bytes_read=5292706 bytes_retransmit=9 bytes_invalid=0 send_seq=651893 receive_seq=651893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=19584 freq=400015877 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43528 bytes_read=136039 bytes_retransmit=0 bytes_invalid=0 send_seq=7226 receive_seq=7226 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999372 adj=49997435 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214178 bytes_read=6943939 bytes_retransmit=9 bytes_invalid=0 send_seq=29970 receive_seq=29970 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997843 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155371 bytes_read=4458122 bytes_retransmit=9 bytes_invalid=0 send_seq=21661 receive_seq=21661 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997606 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43795 bytes_read=1797095 bytes_retransmit=9 bytes_invalid=0 send_seq=7240 receive_seq=7240 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997705 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44281 bytes_read=133376 bytes_retransmit=9 bytes_invalid=0 send_seq=7227 receive_seq=7227 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98373 bytes_read=2730909 bytes_retransmit=0 bytes_invalid=0 send_seq=11786 receive_seq=11786 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998687 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.7 th2: temp=61.9 th3: temp=59.3 sysload=0.25 cputime=554.359 memavail=7393776 print_time=7061.801 buffer_time=2.115 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 7038.0: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34710219 bytes_read=5294227 bytes_retransmit=9 bytes_invalid=0 send_seq=652133 receive_seq=652132 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=21836 freq=400015871 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43534 bytes_read=136068 bytes_retransmit=0 bytes_invalid=0 send_seq=7227 receive_seq=7227 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999371 adj=49997425 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214184 bytes_read=6944039 bytes_retransmit=9 bytes_invalid=0 send_seq=29971 receive_seq=29971 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997787 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155447 bytes_read=4461195 bytes_retransmit=9 bytes_invalid=0 send_seq=21672 receive_seq=21672 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997561 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43801 bytes_read=1797374 bytes_retransmit=9 bytes_invalid=0 send_seq=7241 receive_seq=7241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44287 bytes_read=133392 bytes_retransmit=9 bytes_invalid=0 send_seq=7228 receive_seq=7228 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98379 bytes_read=2731265 bytes_retransmit=0 bytes_invalid=0 send_seq=11787 receive_seq=11787 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998683 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.4 th2: temp=61.9 th3: temp=59.4 sysload=0.25 cputime=554.502 memavail=7392768 print_time=7062.731 buffer_time=2.044 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Testing frequency 121 Hz
Testing frequency 122 Hz
Stats 7039.0: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34726762 bytes_read=5295981 bytes_retransmit=9 bytes_invalid=0 send_seq=652415 receive_seq=652415 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=7 upcoming_bytes=24299 freq=400015870 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43540 bytes_read=136084 bytes_retransmit=0 bytes_invalid=0 send_seq=7228 receive_seq=7228 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999369 adj=49997415 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214190 bytes_read=6944139 bytes_retransmit=9 bytes_invalid=0 send_seq=29972 receive_seq=29972 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997760 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155523 bytes_read=4464252 bytes_retransmit=9 bytes_invalid=0 send_seq=21683 receive_seq=21683 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43807 bytes_read=1797608 bytes_retransmit=9 bytes_invalid=0 send_seq=7242 receive_seq=7242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44293 bytes_read=133408 bytes_retransmit=9 bytes_invalid=0 send_seq=7229 receive_seq=7229 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98385 bytes_read=2731621 bytes_retransmit=0 bytes_invalid=0 send_seq=11788 receive_seq=11788 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998687 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.5 th2: temp=61.9 th3: temp=59.4 sysload=0.25 cputime=554.668 memavail=7392788 print_time=7063.934 buffer_time=2.246 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.5 pwm=0.000
Testing frequency 123 Hz
Stats 7040.0: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34743760 bytes_read=5297756 bytes_retransmit=9 bytes_invalid=0 send_seq=652708 receive_seq=652708 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=20008 freq=400015858 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43546 bytes_read=136100 bytes_retransmit=0 bytes_invalid=0 send_seq=7229 receive_seq=7229 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999368 adj=49997394 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214196 bytes_read=6944267 bytes_retransmit=9 bytes_invalid=0 send_seq=29973 receive_seq=29973 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997719 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155599 bytes_read=4467338 bytes_retransmit=9 bytes_invalid=0 send_seq=21694 receive_seq=21694 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997514 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43813 bytes_read=1797872 bytes_retransmit=9 bytes_invalid=0 send_seq=7243 receive_seq=7243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44299 bytes_read=133424 bytes_retransmit=9 bytes_invalid=0 send_seq=7230 receive_seq=7230 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98391 bytes_read=2731977 bytes_retransmit=0 bytes_invalid=0 send_seq=11789 receive_seq=11789 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998675 coil_temp=16.9 refs=0 mcu_temp=20.21 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.6 th2: temp=61.9 th3: temp=59.3 sysload=0.25 cputime=554.819 memavail=7392788 print_time=7064.802 buffer_time=2.114 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 7041.0: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34757699 bytes_read=5299281 bytes_retransmit=9 bytes_invalid=0 send_seq=652952 receive_seq=652951 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=8 upcoming_bytes=22464 freq=400015856 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43552 bytes_read=136116 bytes_retransmit=0 bytes_invalid=0 send_seq=7230 receive_seq=7230 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999369 adj=49997398 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214202 bytes_read=6944381 bytes_retransmit=9 bytes_invalid=0 send_seq=29974 receive_seq=29974 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997715 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155675 bytes_read=4470395 bytes_retransmit=9 bytes_invalid=0 send_seq=21705 receive_seq=21705 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997516 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43819 bytes_read=1798151 bytes_retransmit=9 bytes_invalid=0 send_seq=7244 receive_seq=7244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44305 bytes_read=133440 bytes_retransmit=9 bytes_invalid=0 send_seq=7231 receive_seq=7231 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999462 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98397 bytes_read=2732333 bytes_retransmit=0 bytes_invalid=0 send_seq=11790 receive_seq=11790 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998683 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.6 th2: temp=61.9 th3: temp=59.4 sysload=0.31 cputime=554.962 memavail=7392788 print_time=7065.731 buffer_time=2.043 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Testing frequency 124 Hz
Testing frequency 125 Hz
Stats 7042.0: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34774618 bytes_read=5301080 bytes_retransmit=9 bytes_invalid=0 send_seq=653243 receive_seq=653243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=18 upcoming_bytes=24649 freq=400015875 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43558 bytes_read=136132 bytes_retransmit=0 bytes_invalid=0 send_seq=7231 receive_seq=7231 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999368 adj=49997402 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214208 bytes_read=6944481 bytes_retransmit=9 bytes_invalid=0 send_seq=29975 receive_seq=29975 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997696 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155751 bytes_read=4473453 bytes_retransmit=9 bytes_invalid=0 send_seq=21716 receive_seq=21716 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997503 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43825 bytes_read=1798385 bytes_retransmit=9 bytes_invalid=0 send_seq=7245 receive_seq=7245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997670 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44311 bytes_read=133467 bytes_retransmit=9 bytes_invalid=0 send_seq=7232 receive_seq=7232 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999461 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98403 bytes_read=2732689 bytes_retransmit=0 bytes_invalid=0 send_seq=11791 receive_seq=11791 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998674 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.3 th1: temp=56.7 th2: temp=62.0 th3: temp=59.4 sysload=0.31 cputime=555.132 memavail=7392788 print_time=7066.939 buffer_time=2.250 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 126 Hz
Stats 7043.0: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34791991 bytes_read=5302872 bytes_retransmit=9 bytes_invalid=0 send_seq=653538 receive_seq=653537 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=20040 freq=400015873 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=43564 bytes_read=136161 bytes_retransmit=0 bytes_invalid=0 send_seq=7232 receive_seq=7232 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999367 adj=49997363 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214214 bytes_read=6944609 bytes_retransmit=9 bytes_invalid=0 send_seq=29976 receive_seq=29976 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997655 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155827 bytes_read=4476615 bytes_retransmit=9 bytes_invalid=0 send_seq=21727 receive_seq=21727 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997468 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43831 bytes_read=1798649 bytes_retransmit=9 bytes_invalid=0 send_seq=7246 receive_seq=7246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997639 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44317 bytes_read=133483 bytes_retransmit=9 bytes_invalid=0 send_seq=7233 receive_seq=7233 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999447 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98409 bytes_read=2733045 bytes_retransmit=0 bytes_invalid=0 send_seq=11792 receive_seq=11792 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998652 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.4 th1: temp=56.6 th2: temp=61.7 th3: temp=59.4 sysload=0.31 cputime=555.288 memavail=7392788 print_time=7067.809 buffer_time=2.119 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Testing frequency 127 Hz
Stats 7044.0: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34805949 bytes_read=5304402 bytes_retransmit=9 bytes_invalid=0 send_seq=653781 receive_seq=653781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=22596 freq=400015894 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=43570 bytes_read=136177 bytes_retransmit=0 bytes_invalid=0 send_seq=7233 receive_seq=7233 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999366 adj=49997361 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214220 bytes_read=6944709 bytes_retransmit=9 bytes_invalid=0 send_seq=29977 receive_seq=29977 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997712 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155903 bytes_read=4479673 bytes_retransmit=9 bytes_invalid=0 send_seq=21738 receive_seq=21738 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997457 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43837 bytes_read=1798913 bytes_retransmit=9 bytes_invalid=0 send_seq=7247 receive_seq=7247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44323 bytes_read=133499 bytes_retransmit=9 bytes_invalid=0 send_seq=7234 receive_seq=7234 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98415 bytes_read=2733401 bytes_retransmit=0 bytes_invalid=0 send_seq=11793 receive_seq=11793 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998650 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.5 th2: temp=61.9 th3: temp=59.3 sysload=0.31 cputime=555.436 memavail=7392788 print_time=7068.741 buffer_time=2.052 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 128 Hz
Stats 7045.0: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34822857 bytes_read=5306186 bytes_retransmit=9 bytes_invalid=0 send_seq=654070 receive_seq=654070 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=24768 freq=400015913 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=43576 bytes_read=136193 bytes_retransmit=0 bytes_invalid=0 send_seq=7234 receive_seq=7234 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999366 adj=49997318 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214226 bytes_read=6944809 bytes_retransmit=9 bytes_invalid=0 send_seq=29978 receive_seq=29978 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997640 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=155979 bytes_read=4482732 bytes_retransmit=9 bytes_invalid=0 send_seq=21749 receive_seq=21749 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997408 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43843 bytes_read=1799153 bytes_retransmit=9 bytes_invalid=0 send_seq=7248 receive_seq=7248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997607 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44329 bytes_read=133515 bytes_retransmit=9 bytes_invalid=0 send_seq=7235 receive_seq=7235 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98421 bytes_read=2733757 bytes_retransmit=0 bytes_invalid=0 send_seq=11794 receive_seq=11794 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998628 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.5 th2: temp=61.9 th3: temp=59.5 sysload=0.31 cputime=555.607 memavail=7392564 print_time=7069.940 buffer_time=2.250 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 129 Hz
Stats 7046.0: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34840215 bytes_read=5307991 bytes_retransmit=9 bytes_invalid=0 send_seq=654369 receive_seq=654369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=32 upcoming_bytes=20312 freq=400015912 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=43582 bytes_read=136209 bytes_retransmit=0 bytes_invalid=0 send_seq=7235 receive_seq=7235 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999366 adj=49997298 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214232 bytes_read=6944951 bytes_retransmit=9 bytes_invalid=0 send_seq=29979 receive_seq=29979 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997604 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=156048 bytes_read=4485794 bytes_retransmit=9 bytes_invalid=0 send_seq=21759 receive_seq=21759 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997448 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43849 bytes_read=1799399 bytes_retransmit=9 bytes_invalid=0 send_seq=7249 receive_seq=7249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997596 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44335 bytes_read=133531 bytes_retransmit=9 bytes_invalid=0 send_seq=7236 receive_seq=7236 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999430 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98427 bytes_read=2734113 bytes_retransmit=0 bytes_invalid=0 send_seq=11795 receive_seq=11795 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998619 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.9 th2: temp=61.9 th3: temp=59.4 sysload=0.28 cputime=555.765 memavail=7392592 print_time=7070.817 buffer_time=2.127 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 130 Hz
Stats 7047.0: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34854192 bytes_read=5309516 bytes_retransmit=9 bytes_invalid=0 send_seq=654612 receive_seq=654612 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=45 upcoming_bytes=22852 freq=400015891 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000007 bytes_write=43588 bytes_read=136225 bytes_retransmit=0 bytes_invalid=0 send_seq=7236 receive_seq=7236 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999366 adj=49997312 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214238 bytes_read=6945051 bytes_retransmit=9 bytes_invalid=0 send_seq=29980 receive_seq=29980 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997684 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=156124 bytes_read=4488854 bytes_retransmit=9 bytes_invalid=0 send_seq=21770 receive_seq=21770 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997439 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43855 bytes_read=1799645 bytes_retransmit=9 bytes_invalid=0 send_seq=7250 receive_seq=7250 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997596 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44341 bytes_read=133558 bytes_retransmit=9 bytes_invalid=0 send_seq=7237 receive_seq=7237 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999431 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98433 bytes_read=2734469 bytes_retransmit=0 bytes_invalid=0 send_seq=11796 receive_seq=11796 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998625 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.9 th1: temp=56.4 th2: temp=61.9 th3: temp=59.4 sysload=0.28 cputime=555.917 memavail=7392592 print_time=7071.741 buffer_time=2.050 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 131 Hz
Stats 7048.0: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34871271 bytes_read=5311346 bytes_retransmit=9 bytes_invalid=0 send_seq=654907 receive_seq=654907 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=25348 freq=400015888 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43594 bytes_read=136254 bytes_retransmit=0 bytes_invalid=0 send_seq=7237 receive_seq=7237 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999367 adj=49997357 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214244 bytes_read=6945151 bytes_retransmit=9 bytes_invalid=0 send_seq=29981 receive_seq=29981 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997716 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=156200 bytes_read=4491928 bytes_retransmit=9 bytes_invalid=0 send_seq=21781 receive_seq=21781 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997497 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43861 bytes_read=1799863 bytes_retransmit=9 bytes_invalid=0 send_seq=7251 receive_seq=7251 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44347 bytes_read=133574 bytes_retransmit=9 bytes_invalid=0 send_seq=7238 receive_seq=7238 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98439 bytes_read=2734825 bytes_retransmit=0 bytes_invalid=0 send_seq=11797 receive_seq=11797 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998652 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.5 th2: temp=61.9 th3: temp=59.4 sysload=0.28 cputime=556.108 memavail=7393448 print_time=7072.942 buffer_time=2.250 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Testing frequency 132 Hz
Stats 7049.0: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34888788 bytes_read=5313166 bytes_retransmit=9 bytes_invalid=0 send_seq=655209 receive_seq=655209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=16 upcoming_bytes=21000 freq=400015887 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43600 bytes_read=136270 bytes_retransmit=0 bytes_invalid=0 send_seq=7238 receive_seq=7238 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999367 adj=49997374 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214250 bytes_read=6945279 bytes_retransmit=9 bytes_invalid=0 send_seq=29982 receive_seq=29982 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997704 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=156276 bytes_read=4495012 bytes_retransmit=9 bytes_invalid=0 send_seq=21792 receive_seq=21792 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997508 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43867 bytes_read=1800109 bytes_retransmit=9 bytes_invalid=0 send_seq=7252 receive_seq=7252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997645 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44353 bytes_read=133590 bytes_retransmit=9 bytes_invalid=0 send_seq=7239 receive_seq=7239 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98445 bytes_read=2735181 bytes_retransmit=0 bytes_invalid=0 send_seq=11798 receive_seq=11798 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998652 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.3 th1: temp=56.5 th2: temp=61.7 th3: temp=59.4 sysload=0.28 cputime=556.269 memavail=7393448 print_time=7073.817 buffer_time=2.125 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Re-enabled [input_shaper]
Stats 7050.0: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34903303 bytes_read=5314736 bytes_retransmit=9 bytes_invalid=0 send_seq=655461 receive_seq=655461 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=48 upcoming_bytes=24596 freq=400016082 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43606 bytes_read=136286 bytes_retransmit=0 bytes_invalid=0 send_seq=7239 receive_seq=7239 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999369 adj=49997383 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214256 bytes_read=6945379 bytes_retransmit=9 bytes_invalid=0 send_seq=29983 receive_seq=29983 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000242 adj=63997684 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=156352 bytes_read=4498068 bytes_retransmit=9 bytes_invalid=0 send_seq=21803 receive_seq=21803 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997493 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43873 bytes_read=1800370 bytes_retransmit=9 bytes_invalid=0 send_seq=7253 receive_seq=7253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997641 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44359 bytes_read=133606 bytes_retransmit=9 bytes_invalid=0 send_seq=7240 receive_seq=7240 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98451 bytes_read=2735537 bytes_retransmit=0 bytes_invalid=0 send_seq=11799 receive_seq=11799 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998650 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.6 th2: temp=61.6 th3: temp=59.4 sysload=0.28 cputime=556.424 memavail=7393448 print_time=7074.794 buffer_time=2.102 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 7051.0: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34920560 bytes_read=5316545 bytes_retransmit=9 bytes_invalid=0 send_seq=655755 receive_seq=655755 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=40 upcoming_bytes=9000 freq=400016068 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43612 bytes_read=136302 bytes_retransmit=0 bytes_invalid=0 send_seq=7240 receive_seq=7240 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999369 adj=49997104 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214262 bytes_read=6945493 bytes_retransmit=9 bytes_invalid=0 send_seq=29984 receive_seq=29984 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000245 adj=63997408 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=156428 bytes_read=4501185 bytes_retransmit=9 bytes_invalid=0 send_seq=21814 receive_seq=21814 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997086 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43879 bytes_read=1800603 bytes_retransmit=9 bytes_invalid=0 send_seq=7254 receive_seq=7254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997363 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44365 bytes_read=133622 bytes_retransmit=9 bytes_invalid=0 send_seq=7241 receive_seq=7241 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999379 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98457 bytes_read=2735893 bytes_retransmit=0 bytes_invalid=0 send_seq=11800 receive_seq=11800 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998473 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.4 th2: temp=61.9 th3: temp=59.5 sysload=0.26 cputime=556.518 memavail=7393224 print_time=7074.794 buffer_time=1.101 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7052.0: gcodein=0  mcu: mcu_awake=0.014 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34930683 bytes_read=5317755 bytes_retransmit=9 bytes_invalid=0 send_seq=655935 receive_seq=655935 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016039 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43618 bytes_read=136318 bytes_retransmit=0 bytes_invalid=0 send_seq=7241 receive_seq=7241 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999368 adj=49997125 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214268 bytes_read=6945621 bytes_retransmit=9 bytes_invalid=0 send_seq=29985 receive_seq=29985 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000243 adj=63997478 toolboard_t1: mcu_awake=0.317 mcu_task_avg=0.000119 mcu_task_stddev=0.000069 bytes_write=156504 bytes_read=4504271 bytes_retransmit=9 bytes_invalid=0 send_seq=21825 receive_seq=21825 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997142 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43885 bytes_read=1800867 bytes_retransmit=9 bytes_invalid=0 send_seq=7255 receive_seq=7255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997381 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44371 bytes_read=133649 bytes_retransmit=9 bytes_invalid=0 send_seq=7242 receive_seq=7242 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999383 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98463 bytes_read=2736249 bytes_retransmit=0 bytes_invalid=0 send_seq=11801 receive_seq=11801 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998486 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.5 th2: temp=62.0 th3: temp=59.4 sysload=0.26 cputime=556.599 memavail=7393224 print_time=7074.794 buffer_time=0.100 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
LIS2DW finished 'toolboard_t1' measurements
Resonances data written to /tmp/resonances_y_125.000_250.000_20.000_t1_mirror.csv file
Running Command {generate_shaper_graphs}...:
please wait...

Stats 7053.0: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34930956 bytes_read=5318171 bytes_retransmit=9 bytes_invalid=0 send_seq=655953 receive_seq=655953 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016018 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43624 bytes_read=136346 bytes_retransmit=0 bytes_invalid=0 send_seq=7242 receive_seq=7242 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999368 adj=49997159 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214274 bytes_read=6945721 bytes_retransmit=9 bytes_invalid=0 send_seq=29986 receive_seq=29986 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000241 adj=63997510 toolboard_t1: mcu_awake=0.286 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=156572 bytes_read=4505118 bytes_retransmit=9 bytes_invalid=0 send_seq=21833 receive_seq=21833 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997180 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43891 bytes_read=1801131 bytes_retransmit=9 bytes_invalid=0 send_seq=7256 receive_seq=7256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997446 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44377 bytes_read=133665 bytes_retransmit=9 bytes_invalid=0 send_seq=7243 receive_seq=7243 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999394 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98469 bytes_read=2736605 bytes_retransmit=0 bytes_invalid=0 send_seq=11802 receive_seq=11802 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998509 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.0 th1: temp=56.6 th2: temp=61.9 th3: temp=59.4 sysload=0.26 cputime=556.731 memavail=7383800 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 7054.0: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34931244 bytes_read=5318611 bytes_retransmit=9 bytes_invalid=0 send_seq=655974 receive_seq=655974 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015995 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43630 bytes_read=136361 bytes_retransmit=0 bytes_invalid=0 send_seq=7243 receive_seq=7243 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999370 adj=49997190 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214280 bytes_read=6945821 bytes_retransmit=9 bytes_invalid=0 send_seq=29987 receive_seq=29987 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000241 adj=63997534 toolboard_t1: mcu_awake=0.286 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=156578 bytes_read=4505218 bytes_retransmit=9 bytes_invalid=0 send_seq=21834 receive_seq=21834 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997215 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43897 bytes_read=1801365 bytes_retransmit=9 bytes_invalid=0 send_seq=7257 receive_seq=7257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997475 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44383 bytes_read=133681 bytes_retransmit=9 bytes_invalid=0 send_seq=7244 receive_seq=7244 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999400 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98475 bytes_read=2736961 bytes_retransmit=0 bytes_invalid=0 send_seq=11803 receive_seq=11803 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998527 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.5 th2: temp=61.9 th3: temp=59.4 sysload=0.26 cputime=556.789 memavail=7380524 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 7055.0: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34931542 bytes_read=5319036 bytes_retransmit=9 bytes_invalid=0 send_seq=655997 receive_seq=655997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015973 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43636 bytes_read=136376 bytes_retransmit=0 bytes_invalid=0 send_seq=7244 receive_seq=7244 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999370 adj=49997293 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214286 bytes_read=6945949 bytes_retransmit=9 bytes_invalid=0 send_seq=29988 receive_seq=29988 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000239 adj=63997614 toolboard_t1: mcu_awake=0.286 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=156584 bytes_read=4505346 bytes_retransmit=9 bytes_invalid=0 send_seq=21835 receive_seq=21835 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997313 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43903 bytes_read=1801644 bytes_retransmit=9 bytes_invalid=0 send_seq=7258 receive_seq=7258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997546 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44389 bytes_read=133697 bytes_retransmit=9 bytes_invalid=0 send_seq=7245 receive_seq=7245 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999417 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98481 bytes_read=2737317 bytes_retransmit=0 bytes_invalid=0 send_seq=11804 receive_seq=11804 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998574 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=57.1 th1: temp=56.4 th2: temp=62.0 th3: temp=59.4 sysload=0.26 cputime=556.844 memavail=7380272 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.5 pwm=0.000
Stats 7056.0: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34931840 bytes_read=5319461 bytes_retransmit=9 bytes_invalid=0 send_seq=656020 receive_seq=656020 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015953 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43642 bytes_read=136391 bytes_retransmit=0 bytes_invalid=0 send_seq=7245 receive_seq=7245 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999371 adj=49997365 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214292 bytes_read=6946063 bytes_retransmit=9 bytes_invalid=0 send_seq=29989 receive_seq=29989 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997652 toolboard_t1: mcu_awake=0.286 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=156590 bytes_read=4505446 bytes_retransmit=9 bytes_invalid=0 send_seq=21836 receive_seq=21836 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997395 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43909 bytes_read=1801908 bytes_retransmit=9 bytes_invalid=0 send_seq=7259 receive_seq=7259 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997611 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44395 bytes_read=133713 bytes_retransmit=9 bytes_invalid=0 send_seq=7246 receive_seq=7246 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999434 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98487 bytes_read=2737673 bytes_retransmit=0 bytes_invalid=0 send_seq=11805 receive_seq=11805 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998617 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.2 th2: temp=61.9 th3: temp=59.3 sysload=0.32 cputime=556.898 memavail=7380272 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 7057.0: gcodein=0  mcu: mcu_awake=0.011 mcu_task_avg=0.000005 mcu_task_stddev=0.000004 bytes_write=34932138 bytes_read=5319915 bytes_retransmit=9 bytes_invalid=0 send_seq=656043 receive_seq=656043 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015936 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43648 bytes_read=136406 bytes_retransmit=0 bytes_invalid=0 send_seq=7246 receive_seq=7246 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999371 adj=49997415 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214298 bytes_read=6946163 bytes_retransmit=9 bytes_invalid=0 send_seq=29990 receive_seq=29990 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997695 toolboard_t1: mcu_awake=0.286 mcu_task_avg=0.000118 mcu_task_stddev=0.000069 bytes_write=156596 bytes_read=4505546 bytes_retransmit=9 bytes_invalid=0 send_seq=21837 receive_seq=21837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997456 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43915 bytes_read=1802142 bytes_retransmit=9 bytes_invalid=0 send_seq=7260 receive_seq=7260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997647 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44401 bytes_read=133740 bytes_retransmit=9 bytes_invalid=0 send_seq=7247 receive_seq=7247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98493 bytes_read=2738029 bytes_retransmit=0 bytes_invalid=0 send_seq=11806 receive_seq=11806 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998654 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.7 th1: temp=56.3 th2: temp=62.0 th3: temp=59.7 sysload=0.32 cputime=556.952 memavail=7380272 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 7058.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34932436 bytes_read=5320355 bytes_retransmit=9 bytes_invalid=0 send_seq=656066 receive_seq=656066 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015928 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43654 bytes_read=136422 bytes_retransmit=0 bytes_invalid=0 send_seq=7247 receive_seq=7247 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999370 adj=49997441 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214304 bytes_read=6946291 bytes_retransmit=9 bytes_invalid=0 send_seq=29991 receive_seq=29991 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997719 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156602 bytes_read=4505688 bytes_retransmit=9 bytes_invalid=0 send_seq=21838 receive_seq=21838 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997495 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43921 bytes_read=1802406 bytes_retransmit=9 bytes_invalid=0 send_seq=7261 receive_seq=7261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997673 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44407 bytes_read=133756 bytes_retransmit=9 bytes_invalid=0 send_seq=7248 receive_seq=7248 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98499 bytes_read=2738369 bytes_retransmit=0 bytes_invalid=0 send_seq=11807 receive_seq=11807 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998677 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.6 th1: temp=56.3 th2: temp=62.2 th3: temp=59.5 sysload=0.32 cputime=557.008 memavail=7379264 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 7059.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34932740 bytes_read=5320796 bytes_retransmit=9 bytes_invalid=0 send_seq=656090 receive_seq=656090 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015895 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=43666 bytes_read=136467 bytes_retransmit=0 bytes_invalid=0 send_seq=7249 receive_seq=7249 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999370 adj=49997428 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214316 bytes_read=6946407 bytes_retransmit=9 bytes_invalid=0 send_seq=29993 receive_seq=29993 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997715 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156614 bytes_read=4505804 bytes_retransmit=9 bytes_invalid=0 send_seq=21840 receive_seq=21840 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997688 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=43933 bytes_read=1802686 bytes_retransmit=9 bytes_invalid=0 send_seq=7263 receive_seq=7263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997706 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44419 bytes_read=133788 bytes_retransmit=9 bytes_invalid=0 send_seq=7250 receive_seq=7250 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98511 bytes_read=2738741 bytes_retransmit=0 bytes_invalid=0 send_seq=11809 receive_seq=11809 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998685 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.4 th1: temp=56.3 th2: temp=62.0 th3: temp=59.5 sysload=0.32 cputime=557.064 memavail=7379264 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7060.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34933038 bytes_read=5321250 bytes_retransmit=9 bytes_invalid=0 send_seq=656113 receive_seq=656113 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015882 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=43672 bytes_read=136483 bytes_retransmit=0 bytes_invalid=0 send_seq=7250 receive_seq=7250 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999370 adj=49997483 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214322 bytes_read=6946507 bytes_retransmit=9 bytes_invalid=0 send_seq=29994 receive_seq=29994 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997747 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156620 bytes_read=4505904 bytes_retransmit=9 bytes_invalid=0 send_seq=21841 receive_seq=21841 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997700 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43939 bytes_read=1802935 bytes_retransmit=9 bytes_invalid=0 send_seq=7264 receive_seq=7264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997732 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44425 bytes_read=133804 bytes_retransmit=9 bytes_invalid=0 send_seq=7251 receive_seq=7251 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98517 bytes_read=2739097 bytes_retransmit=0 bytes_invalid=0 send_seq=11810 receive_seq=11810 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998716 coil_temp=16.9 refs=0 mcu_temp=20.22 supply_voltage=3.011 th0: temp=56.4 th1: temp=56.3 th2: temp=62.0 th3: temp=59.5 sysload=0.32 cputime=557.118 memavail=7379264 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 7061.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34933336 bytes_read=5321675 bytes_retransmit=9 bytes_invalid=0 send_seq=656136 receive_seq=656136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015872 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=43678 bytes_read=136499 bytes_retransmit=0 bytes_invalid=0 send_seq=7251 receive_seq=7251 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999369 adj=49997475 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214328 bytes_read=6946649 bytes_retransmit=9 bytes_invalid=0 send_seq=29995 receive_seq=29995 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997753 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156626 bytes_read=4506032 bytes_retransmit=9 bytes_invalid=0 send_seq=21842 receive_seq=21842 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997666 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43945 bytes_read=1803199 bytes_retransmit=9 bytes_invalid=0 send_seq=7265 receive_seq=7265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997731 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44431 bytes_read=133820 bytes_retransmit=9 bytes_invalid=0 send_seq=7252 receive_seq=7252 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999459 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=31.6  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98523 bytes_read=2739453 bytes_retransmit=0 bytes_invalid=0 send_seq=11811 receive_seq=11811 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998719 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.2 th1: temp=56.3 th2: temp=61.9 th3: temp=59.5 sysload=0.37 cputime=557.175 memavail=7377752 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 7062.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34933634 bytes_read=5322100 bytes_retransmit=9 bytes_invalid=0 send_seq=656159 receive_seq=656159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015863 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=43684 bytes_read=136515 bytes_retransmit=0 bytes_invalid=0 send_seq=7252 receive_seq=7252 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999370 adj=49997467 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214334 bytes_read=6946749 bytes_retransmit=9 bytes_invalid=0 send_seq=29996 receive_seq=29996 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997732 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156632 bytes_read=4506132 bytes_retransmit=9 bytes_invalid=0 send_seq=21843 receive_seq=21843 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997634 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43951 bytes_read=1803463 bytes_retransmit=9 bytes_invalid=0 send_seq=7266 receive_seq=7266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997746 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44437 bytes_read=133847 bytes_retransmit=9 bytes_invalid=0 send_seq=7253 receive_seq=7253 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999458 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98529 bytes_read=2739809 bytes_retransmit=0 bytes_invalid=0 send_seq=11812 receive_seq=11812 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998713 coil_temp=16.9 refs=0 mcu_temp=20.23 supply_voltage=3.011 th0: temp=56.1 th1: temp=56.3 th2: temp=62.1 th3: temp=59.4 sysload=0.37 cputime=557.238 memavail=7367952 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Fitted shaper 'zv' frequency = 54.8 Hz (vibrations = 0.6%, smoothing ~= 0.058)
To avoid too much smoothing with 'zv', suggested max_accel <= 11700 mm/sec^2
Fitted shaper 'mzv' frequency = 56.6 Hz (vibrations = 0.0%, smoothing ~= 0.064)
To avoid too much smoothing with 'mzv', suggested max_accel <= 9400 mm/sec^2
Fitted shaper 'ei' frequency = 68.2 Hz (vibrations = 0.0%, smoothing ~= 0.069)
To avoid too much smoothing with 'ei', suggested max_accel <= 8700 mm/sec^2
Fitted shaper '2hump_ei' frequency = 84.8 Hz (vibrations = 0.0%, smoothing ~= 0.075)
To avoid too much smoothing with '2hump_ei', suggested max_accel <= 8000 mm/sec^2
Fitted shaper '3hump_ei' frequency = 101.4 Hz (vibrations = 0.0%, smoothing ~= 0.080)
To avoid too much smoothing with '3hump_ei', suggested max_accel <= 7500 mm/sec^2
Recommended shaper is zv @ 54.8 Hz

Command {generate_shaper_graphs} finished

Running Command {generate_shaper_graphs}...:
please wait...

Stats 7063.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34933922 bytes_read=5322559 bytes_retransmit=9 bytes_invalid=0 send_seq=656180 receive_seq=656180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016071 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000011 bytes_write=43690 bytes_read=136531 bytes_retransmit=0 bytes_invalid=0 send_seq=7253 receive_seq=7253 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999372 adj=49997477 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214340 bytes_read=6946849 bytes_retransmit=9 bytes_invalid=0 send_seq=29997 receive_seq=29997 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997757 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156638 bytes_read=4506246 bytes_retransmit=9 bytes_invalid=0 send_seq=21844 receive_seq=21844 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997617 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43957 bytes_read=1803697 bytes_retransmit=9 bytes_invalid=0 send_seq=7267 receive_seq=7267 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997731 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44443 bytes_read=133863 bytes_retransmit=9 bytes_invalid=0 send_seq=7254 receive_seq=7254 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999474 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98535 bytes_read=2740165 bytes_retransmit=0 bytes_invalid=0 send_seq=11813 receive_seq=11813 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998712 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.0 th1: temp=56.4 th2: temp=62.1 th3: temp=59.5 sysload=0.37 cputime=557.324 memavail=7386660 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 7064.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34934210 bytes_read=5322969 bytes_retransmit=9 bytes_invalid=0 send_seq=656201 receive_seq=656201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016048 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43696 bytes_read=136560 bytes_retransmit=0 bytes_invalid=0 send_seq=7254 receive_seq=7254 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999373 adj=49997086 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214346 bytes_read=6946977 bytes_retransmit=9 bytes_invalid=0 send_seq=29998 receive_seq=29998 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997228 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156644 bytes_read=4506374 bytes_retransmit=9 bytes_invalid=0 send_seq=21845 receive_seq=21845 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997064 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43963 bytes_read=1803976 bytes_retransmit=9 bytes_invalid=0 send_seq=7268 receive_seq=7268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997323 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44449 bytes_read=133879 bytes_retransmit=9 bytes_invalid=0 send_seq=7255 receive_seq=7255 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999371 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98541 bytes_read=2740521 bytes_retransmit=0 bytes_invalid=0 send_seq=11814 receive_seq=11814 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998438 coil_temp=16.9 refs=0 mcu_temp=20.24 supply_voltage=3.011 th0: temp=56.0 th1: temp=56.3 th2: temp=61.8 th3: temp=59.4 sysload=0.37 cputime=557.383 memavail=7380864 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 7065.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34934508 bytes_read=5323392 bytes_retransmit=9 bytes_invalid=0 send_seq=656224 receive_seq=656224 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016027 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43702 bytes_read=136576 bytes_retransmit=0 bytes_invalid=0 send_seq=7255 receive_seq=7255 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999373 adj=49997208 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214352 bytes_read=6947077 bytes_retransmit=9 bytes_invalid=0 send_seq=29999 receive_seq=29999 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997396 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156650 bytes_read=4506474 bytes_retransmit=9 bytes_invalid=0 send_seq=21846 receive_seq=21846 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997215 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43969 bytes_read=1804240 bytes_retransmit=9 bytes_invalid=0 send_seq=7269 receive_seq=7269 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997438 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44455 bytes_read=133895 bytes_retransmit=9 bytes_invalid=0 send_seq=7256 receive_seq=7256 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999395 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=31.6  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98547 bytes_read=2740877 bytes_retransmit=0 bytes_invalid=0 send_seq=11815 receive_seq=11815 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998531 coil_temp=16.9 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=55.9 th1: temp=56.0 th2: temp=62.0 th3: temp=59.3 sysload=0.37 cputime=557.440 memavail=7373308 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 7066.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34934806 bytes_read=5323846 bytes_retransmit=9 bytes_invalid=0 send_seq=656247 receive_seq=656247 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016009 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43708 bytes_read=136592 bytes_retransmit=0 bytes_invalid=0 send_seq=7256 receive_seq=7256 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999373 adj=49997292 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214358 bytes_read=6947191 bytes_retransmit=9 bytes_invalid=0 send_seq=30000 receive_seq=30000 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997487 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156656 bytes_read=4506574 bytes_retransmit=9 bytes_invalid=0 send_seq=21847 receive_seq=21847 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997340 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43975 bytes_read=1804474 bytes_retransmit=9 bytes_invalid=0 send_seq=7270 receive_seq=7270 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997524 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44461 bytes_read=133911 bytes_retransmit=9 bytes_invalid=0 send_seq=7257 receive_seq=7257 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999412 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98553 bytes_read=2741233 bytes_retransmit=0 bytes_invalid=0 send_seq=11816 receive_seq=11816 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998582 coil_temp=16.9 refs=0 mcu_temp=20.25 supply_voltage=3.011 th0: temp=55.7 th1: temp=56.1 th2: temp=61.9 th3: temp=59.4 sysload=0.42 cputime=557.495 memavail=7378688 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7067.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34935104 bytes_read=5324271 bytes_retransmit=9 bytes_invalid=0 send_seq=656270 receive_seq=656270 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015995 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43714 bytes_read=136608 bytes_retransmit=0 bytes_invalid=0 send_seq=7257 receive_seq=7257 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999373 adj=49997351 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214364 bytes_read=6947319 bytes_retransmit=9 bytes_invalid=0 send_seq=30001 receive_seq=30001 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997574 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156662 bytes_read=4506702 bytes_retransmit=9 bytes_invalid=0 send_seq=21848 receive_seq=21848 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997406 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43981 bytes_read=1804753 bytes_retransmit=9 bytes_invalid=0 send_seq=7271 receive_seq=7271 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997577 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44467 bytes_read=133938 bytes_retransmit=9 bytes_invalid=0 send_seq=7258 receive_seq=7258 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999424 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98559 bytes_read=2741589 bytes_retransmit=0 bytes_invalid=0 send_seq=11817 receive_seq=11817 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998623 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=55.8 th1: temp=56.1 th2: temp=61.9 th3: temp=59.4 sysload=0.42 cputime=557.550 memavail=7378688 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7068.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34935402 bytes_read=5324711 bytes_retransmit=9 bytes_invalid=0 send_seq=656293 receive_seq=656293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015975 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43720 bytes_read=136624 bytes_retransmit=0 bytes_invalid=0 send_seq=7258 receive_seq=7258 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999372 adj=49997383 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214370 bytes_read=6947419 bytes_retransmit=9 bytes_invalid=0 send_seq=30002 receive_seq=30002 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997627 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156668 bytes_read=4506816 bytes_retransmit=9 bytes_invalid=0 send_seq=21849 receive_seq=21849 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997450 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43987 bytes_read=1805002 bytes_retransmit=9 bytes_invalid=0 send_seq=7272 receive_seq=7272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997621 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44473 bytes_read=133954 bytes_retransmit=9 bytes_invalid=0 send_seq=7259 receive_seq=7259 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999432 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98565 bytes_read=2741945 bytes_retransmit=0 bytes_invalid=0 send_seq=11818 receive_seq=11818 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998651 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=55.5 th1: temp=56.0 th2: temp=62.0 th3: temp=59.3 sysload=0.42 cputime=557.604 memavail=7378692 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7069.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34935700 bytes_read=5325165 bytes_retransmit=9 bytes_invalid=0 send_seq=656316 receive_seq=656316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015956 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43726 bytes_read=136653 bytes_retransmit=0 bytes_invalid=0 send_seq=7259 receive_seq=7259 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999371 adj=49997406 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214376 bytes_read=6947519 bytes_retransmit=9 bytes_invalid=0 send_seq=30003 receive_seq=30003 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997669 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156674 bytes_read=4506916 bytes_retransmit=9 bytes_invalid=0 send_seq=21850 receive_seq=21850 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997499 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43993 bytes_read=1805236 bytes_retransmit=9 bytes_invalid=0 send_seq=7273 receive_seq=7273 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44479 bytes_read=133970 bytes_retransmit=9 bytes_invalid=0 send_seq=7260 receive_seq=7260 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=31.6  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98571 bytes_read=2742301 bytes_retransmit=0 bytes_invalid=0 send_seq=11819 receive_seq=11819 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998683 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=55.6 th1: temp=56.0 th2: temp=61.9 th3: temp=59.3 sysload=0.42 cputime=557.657 memavail=7378692 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 7070.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34935998 bytes_read=5325590 bytes_retransmit=9 bytes_invalid=0 send_seq=656339 receive_seq=656339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015941 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43732 bytes_read=136669 bytes_retransmit=0 bytes_invalid=0 send_seq=7260 receive_seq=7260 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999371 adj=49997416 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214382 bytes_read=6947647 bytes_retransmit=9 bytes_invalid=0 send_seq=30004 receive_seq=30004 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997707 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156680 bytes_read=4507044 bytes_retransmit=9 bytes_invalid=0 send_seq=21851 receive_seq=21851 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997534 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=43999 bytes_read=1805530 bytes_retransmit=9 bytes_invalid=0 send_seq=7274 receive_seq=7274 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44485 bytes_read=133986 bytes_retransmit=9 bytes_invalid=0 send_seq=7261 receive_seq=7261 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98577 bytes_read=2742657 bytes_retransmit=0 bytes_invalid=0 send_seq=11820 receive_seq=11820 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998750 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=55.5 th1: temp=56.1 th2: temp=62.1 th3: temp=59.5 sysload=0.42 cputime=557.712 memavail=7378692 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 7071.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34936296 bytes_read=5326015 bytes_retransmit=9 bytes_invalid=0 send_seq=656362 receive_seq=656362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015925 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43738 bytes_read=136685 bytes_retransmit=0 bytes_invalid=0 send_seq=7261 receive_seq=7261 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999370 adj=49997429 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214388 bytes_read=6947761 bytes_retransmit=9 bytes_invalid=0 send_seq=30005 receive_seq=30005 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997711 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156686 bytes_read=4507144 bytes_retransmit=9 bytes_invalid=0 send_seq=21852 receive_seq=21852 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997553 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=44005 bytes_read=1805779 bytes_retransmit=9 bytes_invalid=0 send_seq=7275 receive_seq=7275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44491 bytes_read=134002 bytes_retransmit=9 bytes_invalid=0 send_seq=7262 receive_seq=7262 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.5 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=31.6  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98583 bytes_read=2743005 bytes_retransmit=0 bytes_invalid=0 send_seq=11821 receive_seq=11821 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998749 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.011 th0: temp=55.5 th1: temp=55.8 th2: temp=61.9 th3: temp=59.4 sysload=0.47 cputime=557.767 memavail=7375416 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.5 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 7072.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34936594 bytes_read=5326469 bytes_retransmit=9 bytes_invalid=0 send_seq=656385 receive_seq=656385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015913 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43744 bytes_read=136701 bytes_retransmit=0 bytes_invalid=0 send_seq=7262 receive_seq=7262 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999370 adj=49997437 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214394 bytes_read=6947861 bytes_retransmit=9 bytes_invalid=0 send_seq=30006 receive_seq=30006 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997717 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156692 bytes_read=4507244 bytes_retransmit=9 bytes_invalid=0 send_seq=21853 receive_seq=21853 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997568 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=44011 bytes_read=1806013 bytes_retransmit=9 bytes_invalid=0 send_seq=7276 receive_seq=7276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997715 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44497 bytes_read=134029 bytes_retransmit=9 bytes_invalid=0 send_seq=7263 receive_seq=7263 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999491 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=31.6  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98589 bytes_read=2743350 bytes_retransmit=0 bytes_invalid=0 send_seq=11822 receive_seq=11822 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998747 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=55.3 th1: temp=55.9 th2: temp=62.0 th3: temp=59.3 sysload=0.47 cputime=557.829 memavail=7367620 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Fitted shaper 'zv' frequency = 50.4 Hz (vibrations = 27.1%, smoothing ~= 0.067)
To avoid too much smoothing with 'zv', suggested max_accel <= 9900 mm/sec^2
Fitted shaper 'mzv' frequency = 37.0 Hz (vibrations = 9.0%, smoothing ~= 0.149)
To avoid too much smoothing with 'mzv', suggested max_accel <= 4000 mm/sec^2
Fitted shaper 'ei' frequency = 45.2 Hz (vibrations = 7.9%, smoothing ~= 0.158)
To avoid too much smoothing with 'ei', suggested max_accel <= 3800 mm/sec^2
Fitted shaper '2hump_ei' frequency = 41.4 Hz (vibrations = 3.6%, smoothing ~= 0.315)
To avoid too much smoothing with '2hump_ei', suggested max_accel <= 1800 mm/sec^2
Fitted shaper '3hump_ei' frequency = 49.8 Hz (vibrations = 3.3%, smoothing ~= 0.330)
To avoid too much smoothing with '3hump_ei', suggested max_accel <= 1700 mm/sec^2
Recommended shaper is mzv @ 37.0 Hz

Command {generate_shaper_graphs} finished

Running Command {generate_shaper_graphs}...:
please wait...

Stats 7073.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34936892 bytes_read=5326909 bytes_retransmit=9 bytes_invalid=0 send_seq=656408 receive_seq=656408 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015902 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43750 bytes_read=136717 bytes_retransmit=0 bytes_invalid=0 send_seq=7263 receive_seq=7263 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999370 adj=49997443 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214400 bytes_read=6947989 bytes_retransmit=9 bytes_invalid=0 send_seq=30007 receive_seq=30007 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997718 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156698 bytes_read=4507386 bytes_retransmit=9 bytes_invalid=0 send_seq=21854 receive_seq=21854 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997570 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=44017 bytes_read=1806292 bytes_retransmit=9 bytes_invalid=0 send_seq=7277 receive_seq=7277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997724 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44503 bytes_read=134045 bytes_retransmit=9 bytes_invalid=0 send_seq=7264 receive_seq=7264 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999484 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98595 bytes_read=2743695 bytes_retransmit=0 bytes_invalid=0 send_seq=11823 receive_seq=11823 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998740 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=55.3 th1: temp=55.9 th2: temp=61.9 th3: temp=59.3 sysload=0.47 cputime=557.956 memavail=7387112 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7074.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34937185 bytes_read=5327329 bytes_retransmit=9 bytes_invalid=0 send_seq=656430 receive_seq=656430 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015884 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43756 bytes_read=136746 bytes_retransmit=0 bytes_invalid=0 send_seq=7264 receive_seq=7264 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999369 adj=49997446 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214406 bytes_read=6948089 bytes_retransmit=9 bytes_invalid=0 send_seq=30008 receive_seq=30008 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997735 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156704 bytes_read=4507486 bytes_retransmit=9 bytes_invalid=0 send_seq=21855 receive_seq=21855 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997764 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=44023 bytes_read=1806541 bytes_retransmit=9 bytes_invalid=0 send_seq=7278 receive_seq=7278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997746 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44509 bytes_read=134061 bytes_retransmit=9 bytes_invalid=0 send_seq=7265 receive_seq=7265 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999478 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=32.1  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98601 bytes_read=2744040 bytes_retransmit=0 bytes_invalid=0 send_seq=11824 receive_seq=11824 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998733 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=55.3 th1: temp=56.1 th2: temp=61.9 th3: temp=59.3 sysload=0.47 cputime=558.012 memavail=7378544 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7075.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34937473 bytes_read=5327767 bytes_retransmit=9 bytes_invalid=0 send_seq=656451 receive_seq=656451 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015876 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43762 bytes_read=136762 bytes_retransmit=0 bytes_invalid=0 send_seq=7265 receive_seq=7265 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999369 adj=49997463 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214412 bytes_read=6948189 bytes_retransmit=9 bytes_invalid=0 send_seq=30009 receive_seq=30009 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997757 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156710 bytes_read=4507586 bytes_retransmit=9 bytes_invalid=0 send_seq=21856 receive_seq=21856 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997837 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=44029 bytes_read=1806790 bytes_retransmit=9 bytes_invalid=0 send_seq=7279 receive_seq=7279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997770 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44515 bytes_read=134077 bytes_retransmit=9 bytes_invalid=0 send_seq=7266 receive_seq=7266 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999476 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98607 bytes_read=2744385 bytes_retransmit=0 bytes_invalid=0 send_seq=11825 receive_seq=11825 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998755 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=55.1 th1: temp=56.0 th2: temp=62.0 th3: temp=59.3 sysload=0.47 cputime=558.065 memavail=7378044 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7076.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34937771 bytes_read=5328192 bytes_retransmit=9 bytes_invalid=0 send_seq=656474 receive_seq=656474 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015870 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43768 bytes_read=136778 bytes_retransmit=0 bytes_invalid=0 send_seq=7266 receive_seq=7266 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999369 adj=49997452 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214418 bytes_read=6948331 bytes_retransmit=9 bytes_invalid=0 send_seq=30010 receive_seq=30010 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997854 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156716 bytes_read=4507714 bytes_retransmit=9 bytes_invalid=0 send_seq=21857 receive_seq=21857 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997762 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=44035 bytes_read=1807069 bytes_retransmit=9 bytes_invalid=0 send_seq=7280 receive_seq=7280 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997762 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44521 bytes_read=134093 bytes_retransmit=9 bytes_invalid=0 send_seq=7267 receive_seq=7267 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999471 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98613 bytes_read=2744730 bytes_retransmit=0 bytes_invalid=0 send_seq=11826 receive_seq=11826 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998734 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=54.9 th1: temp=56.0 th2: temp=61.9 th3: temp=59.3 sysload=0.59 cputime=558.119 memavail=7378044 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7077.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34938069 bytes_read=5328617 bytes_retransmit=9 bytes_invalid=0 send_seq=656497 receive_seq=656497 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015860 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43774 bytes_read=136794 bytes_retransmit=0 bytes_invalid=0 send_seq=7267 receive_seq=7267 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999369 adj=49997437 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214424 bytes_read=6948431 bytes_retransmit=9 bytes_invalid=0 send_seq=30011 receive_seq=30011 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997886 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156722 bytes_read=4507814 bytes_retransmit=9 bytes_invalid=0 send_seq=21858 receive_seq=21858 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997713 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=44041 bytes_read=1807318 bytes_retransmit=9 bytes_invalid=0 send_seq=7281 receive_seq=7281 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997770 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44527 bytes_read=134120 bytes_retransmit=9 bytes_invalid=0 send_seq=7268 receive_seq=7268 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98619 bytes_read=2745075 bytes_retransmit=0 bytes_invalid=0 send_seq=11827 receive_seq=11827 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998725 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=55.1 th1: temp=55.7 th2: temp=62.2 th3: temp=59.4 sysload=0.59 cputime=558.173 memavail=7378044 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 7078.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34938367 bytes_read=5329086 bytes_retransmit=9 bytes_invalid=0 send_seq=656520 receive_seq=656520 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015860 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43780 bytes_read=136810 bytes_retransmit=0 bytes_invalid=0 send_seq=7268 receive_seq=7268 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999369 adj=49997444 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214430 bytes_read=6948531 bytes_retransmit=9 bytes_invalid=0 send_seq=30012 receive_seq=30012 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000239 adj=63997840 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156728 bytes_read=4507928 bytes_retransmit=9 bytes_invalid=0 send_seq=21859 receive_seq=21859 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997667 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=44047 bytes_read=1807552 bytes_retransmit=9 bytes_invalid=0 send_seq=7282 receive_seq=7282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997751 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44533 bytes_read=134136 bytes_retransmit=9 bytes_invalid=0 send_seq=7269 receive_seq=7269 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999460 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98625 bytes_read=2745420 bytes_retransmit=0 bytes_invalid=0 send_seq=11828 receive_seq=11828 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998728 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=55.3 th1: temp=55.9 th2: temp=61.8 th3: temp=59.3 sysload=0.59 cputime=558.227 memavail=7376804 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 7079.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34938665 bytes_read=5329511 bytes_retransmit=9 bytes_invalid=0 send_seq=656543 receive_seq=656543 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015856 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43786 bytes_read=136839 bytes_retransmit=0 bytes_invalid=0 send_seq=7269 receive_seq=7269 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999369 adj=49997434 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214436 bytes_read=6948659 bytes_retransmit=9 bytes_invalid=0 send_seq=30013 receive_seq=30013 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997932 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156734 bytes_read=4508056 bytes_retransmit=9 bytes_invalid=0 send_seq=21860 receive_seq=21860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997610 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=44053 bytes_read=1807831 bytes_retransmit=9 bytes_invalid=0 send_seq=7283 receive_seq=7283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997722 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44539 bytes_read=134152 bytes_retransmit=9 bytes_invalid=0 send_seq=7270 receive_seq=7270 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999453 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98631 bytes_read=2745768 bytes_retransmit=0 bytes_invalid=0 send_seq=11829 receive_seq=11829 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998717 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=54.9 th1: temp=55.8 th2: temp=62.0 th3: temp=59.2 sysload=0.59 cputime=558.281 memavail=7376804 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.1 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 7080.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34938963 bytes_read=5329936 bytes_retransmit=9 bytes_invalid=0 send_seq=656566 receive_seq=656566 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015849 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43792 bytes_read=136855 bytes_retransmit=0 bytes_invalid=0 send_seq=7270 receive_seq=7270 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999369 adj=49997435 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214442 bytes_read=6948759 bytes_retransmit=9 bytes_invalid=0 send_seq=30014 receive_seq=30014 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997852 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156740 bytes_read=4508156 bytes_retransmit=9 bytes_invalid=0 send_seq=21861 receive_seq=21861 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000060 adj=63997580 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=44059 bytes_read=1808095 bytes_retransmit=9 bytes_invalid=0 send_seq=7284 receive_seq=7284 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997707 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44545 bytes_read=134168 bytes_retransmit=9 bytes_invalid=0 send_seq=7271 receive_seq=7271 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98637 bytes_read=2746124 bytes_retransmit=0 bytes_invalid=0 send_seq=11830 receive_seq=11830 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998754 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=55.1 th1: temp=55.8 th2: temp=62.2 th3: temp=59.4 sysload=0.59 cputime=558.335 memavail=7376812 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7081.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34939261 bytes_read=5330390 bytes_retransmit=9 bytes_invalid=0 send_seq=656589 receive_seq=656589 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015839 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43798 bytes_read=136871 bytes_retransmit=0 bytes_invalid=0 send_seq=7271 receive_seq=7271 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999368 adj=49997436 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214448 bytes_read=6948873 bytes_retransmit=9 bytes_invalid=0 send_seq=30015 receive_seq=30015 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997800 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156746 bytes_read=4508256 bytes_retransmit=9 bytes_invalid=0 send_seq=21862 receive_seq=21862 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997566 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=44065 bytes_read=1808329 bytes_retransmit=9 bytes_invalid=0 send_seq=7285 receive_seq=7285 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997699 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44551 bytes_read=134184 bytes_retransmit=9 bytes_invalid=0 send_seq=7272 receive_seq=7272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999448 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98643 bytes_read=2746480 bytes_retransmit=0 bytes_invalid=0 send_seq=11831 receive_seq=11831 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998730 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=54.6 th1: temp=55.8 th2: temp=61.9 th3: temp=59.2 sysload=0.63 cputime=558.389 memavail=7376812 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7082.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34939554 bytes_read=5330810 bytes_retransmit=9 bytes_invalid=0 send_seq=656611 receive_seq=656611 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015836 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43804 bytes_read=136887 bytes_retransmit=0 bytes_invalid=0 send_seq=7272 receive_seq=7272 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999369 adj=49997426 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214454 bytes_read=6949001 bytes_retransmit=9 bytes_invalid=0 send_seq=30016 receive_seq=30016 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997771 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156752 bytes_read=4508384 bytes_retransmit=9 bytes_invalid=0 send_seq=21863 receive_seq=21863 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997566 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=44071 bytes_read=1808608 bytes_retransmit=9 bytes_invalid=0 send_seq=7286 receive_seq=7286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997706 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44557 bytes_read=134211 bytes_retransmit=9 bytes_invalid=0 send_seq=7273 receive_seq=7273 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98649 bytes_read=2746836 bytes_retransmit=0 bytes_invalid=0 send_seq=11832 receive_seq=11832 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998721 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.011 th0: temp=54.7 th1: temp=55.9 th2: temp=62.1 th3: temp=59.3 sysload=0.63 cputime=558.451 memavail=7363472 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.5 pwm=0.000
Fitted shaper 'zv' frequency = 54.6 Hz (vibrations = 1.1%, smoothing ~= 0.058)
To avoid too much smoothing with 'zv', suggested max_accel <= 11600 mm/sec^2
Fitted shaper 'mzv' frequency = 52.2 Hz (vibrations = 0.0%, smoothing ~= 0.075)
To avoid too much smoothing with 'mzv', suggested max_accel <= 8000 mm/sec^2
Fitted shaper 'ei' frequency = 63.8 Hz (vibrations = 0.0%, smoothing ~= 0.079)
To avoid too much smoothing with 'ei', suggested max_accel <= 7600 mm/sec^2
Fitted shaper '2hump_ei' frequency = 82.2 Hz (vibrations = 0.0%, smoothing ~= 0.080)
To avoid too much smoothing with '2hump_ei', suggested max_accel <= 7500 mm/sec^2
Fitted shaper '3hump_ei' frequency = 101.4 Hz (vibrations = 0.0%, smoothing ~= 0.080)
To avoid too much smoothing with '3hump_ei', suggested max_accel <= 7500 mm/sec^2
Recommended shaper is zv @ 54.6 Hz

Command {generate_shaper_graphs} finished

Running Command {generate_shaper_graphs}...:
Stats 7083.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34939842 bytes_read=5331240 bytes_retransmit=9 bytes_invalid=0 send_seq=656632 receive_seq=656632 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015833 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43810 bytes_read=136903 bytes_retransmit=0 bytes_invalid=0 send_seq=7273 receive_seq=7273 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999369 adj=49997440 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214460 bytes_read=6949101 bytes_retransmit=9 bytes_invalid=0 send_seq=30017 receive_seq=30017 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997732 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156758 bytes_read=4508484 bytes_retransmit=9 bytes_invalid=0 send_seq=21864 receive_seq=21864 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=44077 bytes_read=1808857 bytes_retransmit=9 bytes_invalid=0 send_seq=7287 receive_seq=7287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997696 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44563 bytes_read=134227 bytes_retransmit=9 bytes_invalid=0 send_seq=7274 receive_seq=7274 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999450 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=31.6  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98655 bytes_read=2747192 bytes_retransmit=0 bytes_invalid=0 send_seq=11833 receive_seq=11833 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998706 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=54.8 th1: temp=55.9 th2: temp=61.8 th3: temp=59.4 sysload=0.63 cputime=558.550 memavail=7391600 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
please wait...

Stats 7084.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34940130 bytes_read=5331684 bytes_retransmit=9 bytes_invalid=0 send_seq=656653 receive_seq=656653 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015829 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=43816 bytes_read=136932 bytes_retransmit=0 bytes_invalid=0 send_seq=7274 receive_seq=7274 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999369 adj=49997432 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214466 bytes_read=6949201 bytes_retransmit=9 bytes_invalid=0 send_seq=30018 receive_seq=30018 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997705 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156764 bytes_read=4508598 bytes_retransmit=9 bytes_invalid=0 send_seq=21865 receive_seq=21865 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997535 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=44083 bytes_read=1809091 bytes_retransmit=9 bytes_invalid=0 send_seq=7288 receive_seq=7288 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44569 bytes_read=134243 bytes_retransmit=9 bytes_invalid=0 send_seq=7275 receive_seq=7275 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999451 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=32.1  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98661 bytes_read=2747548 bytes_retransmit=0 bytes_invalid=0 send_seq=11834 receive_seq=11834 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998695 coil_temp=16.9 refs=0 mcu_temp=20.26 supply_voltage=3.012 th0: temp=54.8 th1: temp=55.8 th2: temp=61.9 th3: temp=59.3 sysload=0.63 cputime=558.612 memavail=7380504 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7085.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34940428 bytes_read=5332109 bytes_retransmit=9 bytes_invalid=0 send_seq=656676 receive_seq=656676 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015822 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=43822 bytes_read=136948 bytes_retransmit=0 bytes_invalid=0 send_seq=7275 receive_seq=7275 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999368 adj=49997424 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214472 bytes_read=6949329 bytes_retransmit=9 bytes_invalid=0 send_seq=30019 receive_seq=30019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997700 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156770 bytes_read=4508726 bytes_retransmit=9 bytes_invalid=0 send_seq=21866 receive_seq=21866 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997557 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=44089 bytes_read=1809400 bytes_retransmit=9 bytes_invalid=0 send_seq=7289 receive_seq=7289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997713 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44575 bytes_read=134259 bytes_retransmit=9 bytes_invalid=0 send_seq=7276 receive_seq=7276 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98667 bytes_read=2747904 bytes_retransmit=0 bytes_invalid=0 send_seq=11835 receive_seq=11835 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998708 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=55.0 th1: temp=55.8 th2: temp=61.9 th3: temp=59.3 sysload=0.63 cputime=558.665 memavail=7380000 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 7086.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34940726 bytes_read=5332529 bytes_retransmit=9 bytes_invalid=0 send_seq=656699 receive_seq=656699 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015811 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=43828 bytes_read=136964 bytes_retransmit=0 bytes_invalid=0 send_seq=7276 receive_seq=7276 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999367 adj=49997425 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214478 bytes_read=6949429 bytes_retransmit=9 bytes_invalid=0 send_seq=30020 receive_seq=30020 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000237 adj=63997888 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156776 bytes_read=4508826 bytes_retransmit=9 bytes_invalid=0 send_seq=21867 receive_seq=21867 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997556 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=44095 bytes_read=1809634 bytes_retransmit=9 bytes_invalid=0 send_seq=7290 receive_seq=7290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997710 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44581 bytes_read=134275 bytes_retransmit=9 bytes_invalid=0 send_seq=7277 receive_seq=7277 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999455 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98673 bytes_read=2748260 bytes_retransmit=0 bytes_invalid=0 send_seq=11836 receive_seq=11836 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998703 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=54.9 th1: temp=55.7 th2: temp=61.9 th3: temp=59.2 sysload=0.66 cputime=558.717 memavail=7380008 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7087.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34941024 bytes_read=5332983 bytes_retransmit=9 bytes_invalid=0 send_seq=656722 receive_seq=656722 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015809 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=43834 bytes_read=136980 bytes_retransmit=0 bytes_invalid=0 send_seq=7277 receive_seq=7277 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999367 adj=49997424 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214484 bytes_read=6949543 bytes_retransmit=9 bytes_invalid=0 send_seq=30021 receive_seq=30021 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000244 adj=63997834 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156782 bytes_read=4508926 bytes_retransmit=9 bytes_invalid=0 send_seq=21868 receive_seq=21868 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997577 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=44101 bytes_read=1809868 bytes_retransmit=9 bytes_invalid=0 send_seq=7291 receive_seq=7291 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997714 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44587 bytes_read=134302 bytes_retransmit=9 bytes_invalid=0 send_seq=7278 receive_seq=7278 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999457 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=32.1  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98679 bytes_read=2748616 bytes_retransmit=0 bytes_invalid=0 send_seq=11837 receive_seq=11837 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998714 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.012 th0: temp=54.8 th1: temp=55.8 th2: temp=62.1 th3: temp=59.3 sysload=0.66 cputime=558.769 memavail=7380008 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7088.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34941322 bytes_read=5333423 bytes_retransmit=9 bytes_invalid=0 send_seq=656745 receive_seq=656745 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015811 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=43840 bytes_read=136996 bytes_retransmit=0 bytes_invalid=0 send_seq=7278 receive_seq=7278 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999367 adj=49997416 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214490 bytes_read=6949671 bytes_retransmit=9 bytes_invalid=0 send_seq=30022 receive_seq=30022 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000253 adj=63997905 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156788 bytes_read=4509054 bytes_retransmit=9 bytes_invalid=0 send_seq=21869 receive_seq=21869 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997598 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=44107 bytes_read=1810162 bytes_retransmit=9 bytes_invalid=0 send_seq=7292 receive_seq=7292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997710 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44593 bytes_read=134318 bytes_retransmit=9 bytes_invalid=0 send_seq=7279 receive_seq=7279 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999452 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=31.6  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98685 bytes_read=2748972 bytes_retransmit=0 bytes_invalid=0 send_seq=11838 receive_seq=11838 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998704 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.012 th0: temp=54.6 th1: temp=55.8 th2: temp=61.9 th3: temp=59.3 sysload=0.66 cputime=558.824 memavail=7378780 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 7089.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34941620 bytes_read=5333848 bytes_retransmit=9 bytes_invalid=0 send_seq=656768 receive_seq=656768 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015806 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43846 bytes_read=137025 bytes_retransmit=0 bytes_invalid=0 send_seq=7279 receive_seq=7279 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999367 adj=49997407 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214496 bytes_read=6949771 bytes_retransmit=9 bytes_invalid=0 send_seq=30023 receive_seq=30023 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000250 adj=63998001 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156794 bytes_read=4509168 bytes_retransmit=9 bytes_invalid=0 send_seq=21870 receive_seq=21870 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997569 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=44113 bytes_read=1810396 bytes_retransmit=9 bytes_invalid=0 send_seq=7293 receive_seq=7293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997694 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44599 bytes_read=134334 bytes_retransmit=9 bytes_invalid=0 send_seq=7280 receive_seq=7280 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999490 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=31.6  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98691 bytes_read=2749328 bytes_retransmit=0 bytes_invalid=0 send_seq=11839 receive_seq=11839 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998684 coil_temp=16.9 refs=0 mcu_temp=20.27 supply_voltage=3.012 th0: temp=54.8 th1: temp=55.7 th2: temp=61.9 th3: temp=59.2 sysload=0.66 cputime=558.877 memavail=7378780 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7090.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34941918 bytes_read=5334302 bytes_retransmit=9 bytes_invalid=0 send_seq=656791 receive_seq=656791 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015802 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43852 bytes_read=137041 bytes_retransmit=0 bytes_invalid=0 send_seq=7280 receive_seq=7280 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999366 adj=49997403 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214502 bytes_read=6949867 bytes_retransmit=9 bytes_invalid=0 send_seq=30024 receive_seq=30024 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000259 adj=63997898 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156800 bytes_read=4509264 bytes_retransmit=9 bytes_invalid=0 send_seq=21871 receive_seq=21871 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997561 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=44119 bytes_read=1810645 bytes_retransmit=9 bytes_invalid=0 send_seq=7294 receive_seq=7294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997693 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44605 bytes_read=134350 bytes_retransmit=9 bytes_invalid=0 send_seq=7281 receive_seq=7281 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999479 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=31.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98697 bytes_read=2749684 bytes_retransmit=0 bytes_invalid=0 send_seq=11840 receive_seq=11840 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998711 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=54.6 th1: temp=55.8 th2: temp=61.9 th3: temp=59.3 sysload=0.66 cputime=558.931 memavail=7378780 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7091.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34942216 bytes_read=5334727 bytes_retransmit=9 bytes_invalid=0 send_seq=656814 receive_seq=656814 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015795 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43858 bytes_read=137057 bytes_retransmit=0 bytes_invalid=0 send_seq=7281 receive_seq=7281 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999366 adj=49997405 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214508 bytes_read=6949986 bytes_retransmit=9 bytes_invalid=0 send_seq=30025 receive_seq=30025 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000255 adj=63998001 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156806 bytes_read=4509383 bytes_retransmit=9 bytes_invalid=0 send_seq=21872 receive_seq=21872 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=44125 bytes_read=1810939 bytes_retransmit=9 bytes_invalid=0 send_seq=7295 receive_seq=7295 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999559 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44611 bytes_read=134366 bytes_retransmit=9 bytes_invalid=0 send_seq=7282 receive_seq=7282 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999469 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=31.6  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98703 bytes_read=2750040 bytes_retransmit=0 bytes_invalid=0 send_seq=11841 receive_seq=11841 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998701 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=54.8 th1: temp=55.6 th2: temp=61.9 th3: temp=59.3 sysload=0.68 cputime=558.983 memavail=7378780 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 7092.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34942514 bytes_read=5335152 bytes_retransmit=9 bytes_invalid=0 send_seq=656837 receive_seq=656837 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015795 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43864 bytes_read=137073 bytes_retransmit=0 bytes_invalid=0 send_seq=7282 receive_seq=7282 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999365 adj=49997404 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214514 bytes_read=6950093 bytes_retransmit=9 bytes_invalid=0 send_seq=30026 receive_seq=30026 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000252 adj=63997894 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156812 bytes_read=4509476 bytes_retransmit=9 bytes_invalid=0 send_seq=21873 receive_seq=21873 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=44131 bytes_read=1811173 bytes_retransmit=9 bytes_invalid=0 send_seq=7296 receive_seq=7296 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997706 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44617 bytes_read=134393 bytes_retransmit=9 bytes_invalid=0 send_seq=7283 receive_seq=7283 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999474 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98709 bytes_read=2750396 bytes_retransmit=0 bytes_invalid=0 send_seq=11842 receive_seq=11842 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998699 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.012 th0: temp=54.6 th1: temp=55.7 th2: temp=62.0 th3: temp=59.2 sysload=0.68 cputime=559.042 memavail=7368952 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Fitted shaper 'zv' frequency = 53.2 Hz (vibrations = 20.4%, smoothing ~= 0.061)
To avoid too much smoothing with 'zv', suggested max_accel <= 11000 mm/sec^2
Fitted shaper 'mzv' frequency = 39.0 Hz (vibrations = 1.7%, smoothing ~= 0.134)
To avoid too much smoothing with 'mzv', suggested max_accel <= 4500 mm/sec^2
Fitted shaper 'ei' frequency = 48.0 Hz (vibrations = 1.5%, smoothing ~= 0.140)
To avoid too much smoothing with 'ei', suggested max_accel <= 4300 mm/sec^2
Fitted shaper '2hump_ei' frequency = 44.6 Hz (vibrations = 0.7%, smoothing ~= 0.271)
To avoid too much smoothing with '2hump_ei', suggested max_accel <= 2100 mm/sec^2
Fitted shaper '3hump_ei' frequency = 49.4 Hz (vibrations = 0.5%, smoothing ~= 0.336)
To avoid too much smoothing with '3hump_ei', suggested max_accel <= 1600 mm/sec^2
Recommended shaper is mzv @ 39.0 Hz

Stats 7093.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34942812 bytes_read=5335621 bytes_retransmit=9 bytes_invalid=0 send_seq=656860 receive_seq=656860 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015808 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=43870 bytes_read=137089 bytes_retransmit=0 bytes_invalid=0 send_seq=7283 receive_seq=7283 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999366 adj=49997396 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214520 bytes_read=6950199 bytes_retransmit=9 bytes_invalid=0 send_seq=30027 receive_seq=30027 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000249 adj=63997801 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156818 bytes_read=4509569 bytes_retransmit=9 bytes_invalid=0 send_seq=21874 receive_seq=21874 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997553 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=44137 bytes_read=1811407 bytes_retransmit=9 bytes_invalid=0 send_seq=7297 receive_seq=7297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44623 bytes_read=134409 bytes_retransmit=9 bytes_invalid=0 send_seq=7284 receive_seq=7284 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999464 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=32.1  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98715 bytes_read=2750752 bytes_retransmit=0 bytes_invalid=0 send_seq=11843 receive_seq=11843 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998689 coil_temp=16.9 refs=0 mcu_temp=20.28 supply_voltage=3.011 th0: temp=54.7 th1: temp=55.7 th2: temp=61.9 th3: temp=59.3 sysload=0.68 cputime=559.108 memavail=7366472 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Command {generate_shaper_graphs} finished

toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Stats 7094.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34943110 bytes_read=5336046 bytes_retransmit=9 bytes_invalid=0 send_seq=656883 receive_seq=656883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015805 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=43876 bytes_read=137118 bytes_retransmit=0 bytes_invalid=0 send_seq=7284 receive_seq=7284 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999366 adj=49997377 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214526 bytes_read=6950309 bytes_retransmit=9 bytes_invalid=0 send_seq=30028 receive_seq=30028 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000246 adj=63997707 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=156824 bytes_read=4509706 bytes_retransmit=9 bytes_invalid=0 send_seq=21875 receive_seq=21875 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997523 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=44143 bytes_read=1811701 bytes_retransmit=9 bytes_invalid=0 send_seq=7298 receive_seq=7298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44629 bytes_read=134425 bytes_retransmit=9 bytes_invalid=0 send_seq=7285 receive_seq=7285 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999449 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.3 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98721 bytes_read=2751108 bytes_retransmit=0 bytes_invalid=0 send_seq=11844 receive_seq=11844 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998672 coil_temp=16.9 refs=0 mcu_temp=20.29 supply_voltage=3.011 th0: temp=54.5 th1: temp=55.5 th2: temp=61.8 th3: temp=59.2 sysload=0.68 cputime=559.205 memavail=7390492 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7095.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34943408 bytes_read=5336471 bytes_retransmit=9 bytes_invalid=0 send_seq=656906 receive_seq=656906 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015803 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=43882 bytes_read=137134 bytes_retransmit=0 bytes_invalid=0 send_seq=7285 receive_seq=7285 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999365 adj=49997384 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214532 bytes_read=6950409 bytes_retransmit=9 bytes_invalid=0 send_seq=30029 receive_seq=30029 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000243 adj=63997673 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=156830 bytes_read=4509806 bytes_retransmit=9 bytes_invalid=0 send_seq=21876 receive_seq=21876 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997533 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=44149 bytes_read=1811950 bytes_retransmit=9 bytes_invalid=0 send_seq=7299 receive_seq=7299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997659 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44635 bytes_read=134441 bytes_retransmit=9 bytes_invalid=0 send_seq=7286 receive_seq=7286 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98727 bytes_read=2751464 bytes_retransmit=0 bytes_invalid=0 send_seq=11845 receive_seq=11845 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998673 coil_temp=16.9 refs=0 mcu_temp=20.30 supply_voltage=3.011 th0: temp=54.2 th1: temp=55.6 th2: temp=61.9 th3: temp=59.2 sysload=0.68 cputime=559.249 memavail=7390492 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 7096.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34943696 bytes_read=5336913 bytes_retransmit=9 bytes_invalid=0 send_seq=656927 receive_seq=656927 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015803 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=43888 bytes_read=137150 bytes_retransmit=0 bytes_invalid=0 send_seq=7286 receive_seq=7286 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999364 adj=49997383 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214538 bytes_read=6950523 bytes_retransmit=9 bytes_invalid=0 send_seq=30030 receive_seq=30030 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000241 adj=63997642 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=156836 bytes_read=4509906 bytes_retransmit=9 bytes_invalid=0 send_seq=21877 receive_seq=21877 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997524 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=44155 bytes_read=1812184 bytes_retransmit=9 bytes_invalid=0 send_seq=7300 receive_seq=7300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44641 bytes_read=134457 bytes_retransmit=9 bytes_invalid=0 send_seq=7287 receive_seq=7287 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98733 bytes_read=2751820 bytes_retransmit=0 bytes_invalid=0 send_seq=11846 receive_seq=11846 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998665 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=54.6 th1: temp=55.5 th2: temp=61.8 th3: temp=59.1 sysload=0.63 cputime=559.291 memavail=7390492 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7097.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34943994 bytes_read=5337335 bytes_retransmit=9 bytes_invalid=0 send_seq=656950 receive_seq=656950 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015803 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=43894 bytes_read=137166 bytes_retransmit=0 bytes_invalid=0 send_seq=7287 receive_seq=7287 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999364 adj=49997371 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214544 bytes_read=6950651 bytes_retransmit=9 bytes_invalid=0 send_seq=30031 receive_seq=30031 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997626 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=156842 bytes_read=4510034 bytes_retransmit=9 bytes_invalid=0 send_seq=21878 receive_seq=21878 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997515 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=44161 bytes_read=1812478 bytes_retransmit=9 bytes_invalid=0 send_seq=7301 receive_seq=7301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44647 bytes_read=134484 bytes_retransmit=9 bytes_invalid=0 send_seq=7288 receive_seq=7288 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999440 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98739 bytes_read=2752176 bytes_retransmit=0 bytes_invalid=0 send_seq=11847 receive_seq=11847 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998660 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=54.2 th1: temp=55.7 th2: temp=61.9 th3: temp=59.2 sysload=0.63 cputime=559.339 memavail=7394740 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7098.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34944292 bytes_read=5337775 bytes_retransmit=9 bytes_invalid=0 send_seq=656973 receive_seq=656973 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015805 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=43900 bytes_read=137182 bytes_retransmit=0 bytes_invalid=0 send_seq=7288 receive_seq=7288 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999363 adj=49997368 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214550 bytes_read=6950751 bytes_retransmit=9 bytes_invalid=0 send_seq=30032 receive_seq=30032 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997604 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=156848 bytes_read=4510134 bytes_retransmit=9 bytes_invalid=0 send_seq=21879 receive_seq=21879 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997511 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=44167 bytes_read=1812712 bytes_retransmit=9 bytes_invalid=0 send_seq=7302 receive_seq=7302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44653 bytes_read=134500 bytes_retransmit=9 bytes_invalid=0 send_seq=7289 receive_seq=7289 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98745 bytes_read=2752532 bytes_retransmit=0 bytes_invalid=0 send_seq=11848 receive_seq=11848 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998665 coil_temp=16.9 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.5 th2: temp=61.9 th3: temp=59.3 sysload=0.63 cputime=559.381 memavail=7392988 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7099.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34944590 bytes_read=5338229 bytes_retransmit=9 bytes_invalid=0 send_seq=656996 receive_seq=656996 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015823 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43906 bytes_read=137211 bytes_retransmit=0 bytes_invalid=0 send_seq=7289 receive_seq=7289 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999362 adj=49997354 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214556 bytes_read=6950865 bytes_retransmit=9 bytes_invalid=0 send_seq=30033 receive_seq=30033 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997589 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156854 bytes_read=4510248 bytes_retransmit=9 bytes_invalid=0 send_seq=21880 receive_seq=21880 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997505 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=44173 bytes_read=1812946 bytes_retransmit=9 bytes_invalid=0 send_seq=7303 receive_seq=7303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44659 bytes_read=134516 bytes_retransmit=9 bytes_invalid=0 send_seq=7290 receive_seq=7290 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999439 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98751 bytes_read=2752888 bytes_retransmit=0 bytes_invalid=0 send_seq=11849 receive_seq=11849 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999938 adj=31998663 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.7 th2: temp=61.8 th3: temp=59.2 sysload=0.63 cputime=559.424 memavail=7392988 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7100.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34944888 bytes_read=5338654 bytes_retransmit=9 bytes_invalid=0 send_seq=657019 receive_seq=657019 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015827 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43912 bytes_read=137227 bytes_retransmit=0 bytes_invalid=0 send_seq=7290 receive_seq=7290 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999362 adj=49997308 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214562 bytes_read=6950979 bytes_retransmit=9 bytes_invalid=0 send_seq=30034 receive_seq=30034 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000235 adj=63997548 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156860 bytes_read=4510376 bytes_retransmit=9 bytes_invalid=0 send_seq=21881 receive_seq=21881 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997457 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=44179 bytes_read=1813255 bytes_retransmit=9 bytes_invalid=0 send_seq=7304 receive_seq=7304 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997624 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44665 bytes_read=134532 bytes_retransmit=9 bytes_invalid=0 send_seq=7291 receive_seq=7291 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999429 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98757 bytes_read=2753244 bytes_retransmit=0 bytes_invalid=0 send_seq=11850 receive_seq=11850 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998639 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=54.5 th1: temp=55.7 th2: temp=61.9 th3: temp=59.3 sysload=0.63 cputime=559.475 memavail=7393404 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 7101.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34945186 bytes_read=5339079 bytes_retransmit=9 bytes_invalid=0 send_seq=657042 receive_seq=657042 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015824 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43918 bytes_read=137243 bytes_retransmit=0 bytes_invalid=0 send_seq=7291 receive_seq=7291 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999361 adj=49997321 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=214568 bytes_read=6951079 bytes_retransmit=9 bytes_invalid=0 send_seq=30035 receive_seq=30035 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000239 adj=63997583 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156866 bytes_read=4510476 bytes_retransmit=9 bytes_invalid=0 send_seq=21882 receive_seq=21882 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997476 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=44185 bytes_read=1813489 bytes_retransmit=9 bytes_invalid=0 send_seq=7305 receive_seq=7305 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997626 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44671 bytes_read=134548 bytes_retransmit=9 bytes_invalid=0 send_seq=7292 receive_seq=7292 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999433 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98763 bytes_read=2753600 bytes_retransmit=0 bytes_invalid=0 send_seq=11851 receive_seq=11851 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998649 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=54.7 th1: temp=55.7 th2: temp=62.0 th3: temp=59.1 sysload=0.58 cputime=559.518 memavail=7393404 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7102.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34945484 bytes_read=5339533 bytes_retransmit=9 bytes_invalid=0 send_seq=657065 receive_seq=657065 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015821 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43924 bytes_read=137259 bytes_retransmit=0 bytes_invalid=0 send_seq=7292 receive_seq=7292 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999360 adj=49997336 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214574 bytes_read=6951207 bytes_retransmit=9 bytes_invalid=0 send_seq=30036 receive_seq=30036 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000236 adj=63997683 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156872 bytes_read=4510576 bytes_retransmit=9 bytes_invalid=0 send_seq=21883 receive_seq=21883 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=44191 bytes_read=1813723 bytes_retransmit=9 bytes_invalid=0 send_seq=7306 receive_seq=7306 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997636 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44677 bytes_read=134575 bytes_retransmit=9 bytes_invalid=0 send_seq=7293 receive_seq=7293 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999435 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98769 bytes_read=2753956 bytes_retransmit=0 bytes_invalid=0 send_seq=11852 receive_seq=11852 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998701 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=54.4 th1: temp=55.5 th2: temp=62.0 th3: temp=59.2 sysload=0.58 cputime=559.563 memavail=7393404 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7103.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34945782 bytes_read=5339973 bytes_retransmit=9 bytes_invalid=0 send_seq=657088 receive_seq=657088 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015821 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43930 bytes_read=137275 bytes_retransmit=0 bytes_invalid=0 send_seq=7293 receive_seq=7293 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999359 adj=49997330 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214580 bytes_read=6951321 bytes_retransmit=9 bytes_invalid=0 send_seq=30037 receive_seq=30037 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997657 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156878 bytes_read=4510704 bytes_retransmit=9 bytes_invalid=0 send_seq=21884 receive_seq=21884 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997496 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=44197 bytes_read=1814017 bytes_retransmit=9 bytes_invalid=0 send_seq=7307 receive_seq=7307 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997644 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44683 bytes_read=134591 bytes_retransmit=9 bytes_invalid=0 send_seq=7294 receive_seq=7294 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999437 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98775 bytes_read=2754312 bytes_retransmit=0 bytes_invalid=0 send_seq=11853 receive_seq=11853 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998700 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=54.5 th1: temp=55.4 th2: temp=61.8 th3: temp=59.2 sysload=0.58 cputime=559.607 memavail=7393404 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 7104.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34946080 bytes_read=5340398 bytes_retransmit=9 bytes_invalid=0 send_seq=657111 receive_seq=657111 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015817 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43936 bytes_read=137304 bytes_retransmit=0 bytes_invalid=0 send_seq=7294 receive_seq=7294 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999359 adj=49997332 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214586 bytes_read=6951421 bytes_retransmit=9 bytes_invalid=0 send_seq=30038 receive_seq=30038 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997634 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156884 bytes_read=4510818 bytes_retransmit=9 bytes_invalid=0 send_seq=21885 receive_seq=21885 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997500 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=44203 bytes_read=1814251 bytes_retransmit=9 bytes_invalid=0 send_seq=7308 receive_seq=7308 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44689 bytes_read=134607 bytes_retransmit=9 bytes_invalid=0 send_seq=7295 receive_seq=7295 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98781 bytes_read=2754668 bytes_retransmit=0 bytes_invalid=0 send_seq=11854 receive_seq=11854 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998689 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=54.5 th1: temp=55.7 th2: temp=62.0 th3: temp=59.3 sysload=0.58 cputime=559.651 memavail=7393404 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 7105.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34946378 bytes_read=5340852 bytes_retransmit=9 bytes_invalid=0 send_seq=657134 receive_seq=657134 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015811 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43942 bytes_read=137320 bytes_retransmit=0 bytes_invalid=0 send_seq=7295 receive_seq=7295 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999359 adj=49997355 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214592 bytes_read=6951535 bytes_retransmit=9 bytes_invalid=0 send_seq=30039 receive_seq=30039 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997639 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156890 bytes_read=4510918 bytes_retransmit=9 bytes_invalid=0 send_seq=21886 receive_seq=21886 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997513 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=44209 bytes_read=1814500 bytes_retransmit=9 bytes_invalid=0 send_seq=7309 receive_seq=7309 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44695 bytes_read=134623 bytes_retransmit=9 bytes_invalid=0 send_seq=7296 receive_seq=7296 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98787 bytes_read=2755024 bytes_retransmit=0 bytes_invalid=0 send_seq=11855 receive_seq=11855 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998686 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=54.5 th1: temp=55.6 th2: temp=61.8 th3: temp=59.4 sysload=0.58 cputime=559.696 memavail=7393404 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=19.0 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 7106.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34946676 bytes_read=5341277 bytes_retransmit=9 bytes_invalid=0 send_seq=657157 receive_seq=657157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015806 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43948 bytes_read=137336 bytes_retransmit=0 bytes_invalid=0 send_seq=7296 receive_seq=7296 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999359 adj=49997373 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214598 bytes_read=6951649 bytes_retransmit=9 bytes_invalid=0 send_seq=30040 receive_seq=30040 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997638 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156896 bytes_read=4511046 bytes_retransmit=9 bytes_invalid=0 send_seq=21887 receive_seq=21887 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=44215 bytes_read=1814794 bytes_retransmit=9 bytes_invalid=0 send_seq=7310 receive_seq=7310 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997690 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44701 bytes_read=134639 bytes_retransmit=9 bytes_invalid=0 send_seq=7297 receive_seq=7297 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98793 bytes_read=2755380 bytes_retransmit=0 bytes_invalid=0 send_seq=11856 receive_seq=11856 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998683 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=54.4 th1: temp=55.6 th2: temp=61.9 th3: temp=59.2 sysload=0.53 cputime=559.742 memavail=7393404 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 7107.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34946974 bytes_read=5341700 bytes_retransmit=9 bytes_invalid=0 send_seq=657180 receive_seq=657180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015804 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43954 bytes_read=137352 bytes_retransmit=0 bytes_invalid=0 send_seq=7297 receive_seq=7297 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999359 adj=49997387 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214604 bytes_read=6951763 bytes_retransmit=9 bytes_invalid=0 send_seq=30041 receive_seq=30041 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997641 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156902 bytes_read=4511146 bytes_retransmit=9 bytes_invalid=0 send_seq=21888 receive_seq=21888 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997547 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=44221 bytes_read=1815028 bytes_retransmit=9 bytes_invalid=0 send_seq=7311 receive_seq=7311 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997722 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44707 bytes_read=134666 bytes_retransmit=9 bytes_invalid=0 send_seq=7298 receive_seq=7298 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999445 Octopus_Pro_H723_V1.1: temp=28.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98799 bytes_read=2755736 bytes_retransmit=0 bytes_invalid=0 send_seq=11857 receive_seq=11857 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998687 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.5 th2: temp=61.9 th3: temp=59.3 sysload=0.53 cputime=559.787 memavail=7393404 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7108.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34947272 bytes_read=5342166 bytes_retransmit=9 bytes_invalid=0 send_seq=657203 receive_seq=657203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015803 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43960 bytes_read=137368 bytes_retransmit=0 bytes_invalid=0 send_seq=7298 receive_seq=7298 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999358 adj=49997381 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214610 bytes_read=6951877 bytes_retransmit=9 bytes_invalid=0 send_seq=30042 receive_seq=30042 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000234 adj=63997630 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156908 bytes_read=4511246 bytes_retransmit=9 bytes_invalid=0 send_seq=21889 receive_seq=21889 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997538 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=44227 bytes_read=1815262 bytes_retransmit=9 bytes_invalid=0 send_seq=7312 receive_seq=7312 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997717 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44713 bytes_read=134682 bytes_retransmit=9 bytes_invalid=0 send_seq=7299 receive_seq=7299 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98805 bytes_read=2756092 bytes_retransmit=0 bytes_invalid=0 send_seq=11858 receive_seq=11858 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998696 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.011 th0: temp=54.7 th1: temp=55.3 th2: temp=61.7 th3: temp=59.3 sysload=0.53 cputime=559.831 memavail=7391904 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.5 pwm=0.000
Stats 7109.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34947570 bytes_read=5342591 bytes_retransmit=9 bytes_invalid=0 send_seq=657226 receive_seq=657226 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015804 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43966 bytes_read=137397 bytes_retransmit=0 bytes_invalid=0 send_seq=7299 receive_seq=7299 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999357 adj=49997372 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214616 bytes_read=6951991 bytes_retransmit=9 bytes_invalid=0 send_seq=30043 receive_seq=30043 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000242 adj=63997763 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156914 bytes_read=4511388 bytes_retransmit=9 bytes_invalid=0 send_seq=21890 receive_seq=21890 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997539 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=44233 bytes_read=1815556 bytes_retransmit=9 bytes_invalid=0 send_seq=7313 receive_seq=7313 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997697 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44719 bytes_read=134698 bytes_retransmit=9 bytes_invalid=0 send_seq=7300 receive_seq=7300 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999444 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98811 bytes_read=2756448 bytes_retransmit=0 bytes_invalid=0 send_seq=11859 receive_seq=11859 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998701 coil_temp=16.9 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=53.9 th1: temp=55.5 th2: temp=61.9 th3: temp=59.3 sysload=0.53 cputime=559.876 memavail=7391904 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 7110.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34947868 bytes_read=5343016 bytes_retransmit=9 bytes_invalid=0 send_seq=657249 receive_seq=657249 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015813 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43972 bytes_read=137413 bytes_retransmit=0 bytes_invalid=0 send_seq=7300 receive_seq=7300 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999357 adj=49997363 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214622 bytes_read=6952091 bytes_retransmit=9 bytes_invalid=0 send_seq=30044 receive_seq=30044 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000240 adj=63997865 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156920 bytes_read=4511488 bytes_retransmit=9 bytes_invalid=0 send_seq=21891 receive_seq=21891 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=44239 bytes_read=1815805 bytes_retransmit=9 bytes_invalid=0 send_seq=7314 receive_seq=7314 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997682 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44725 bytes_read=134714 bytes_retransmit=9 bytes_invalid=0 send_seq=7301 receive_seq=7301 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999442 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98817 bytes_read=2756804 bytes_retransmit=0 bytes_invalid=0 send_seq=11860 receive_seq=11860 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998695 coil_temp=16.9 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=54.3 th1: temp=55.5 th2: temp=61.9 th3: temp=59.2 sysload=0.53 cputime=559.919 memavail=7391904 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 7111.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34948166 bytes_read=5343470 bytes_retransmit=9 bytes_invalid=0 send_seq=657272 receive_seq=657272 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015812 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43978 bytes_read=137429 bytes_retransmit=0 bytes_invalid=0 send_seq=7301 receive_seq=7301 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999357 adj=49997352 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214628 bytes_read=6952205 bytes_retransmit=9 bytes_invalid=0 send_seq=30045 receive_seq=30045 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997774 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156926 bytes_read=4511588 bytes_retransmit=9 bytes_invalid=0 send_seq=21892 receive_seq=21892 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997513 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=44245 bytes_read=1816039 bytes_retransmit=9 bytes_invalid=0 send_seq=7315 receive_seq=7315 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44731 bytes_read=134730 bytes_retransmit=9 bytes_invalid=0 send_seq=7302 receive_seq=7302 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=28.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.5 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98823 bytes_read=2757160 bytes_retransmit=0 bytes_invalid=0 send_seq=11861 receive_seq=11861 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998680 coil_temp=16.9 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=54.4 th1: temp=55.6 th2: temp=62.1 th3: temp=59.2 sysload=0.57 cputime=559.962 memavail=7391904 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 7112.0: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=34948464 bytes_read=5343895 bytes_retransmit=9 bytes_invalid=0 send_seq=657295 receive_seq=657295 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015808 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=43984 bytes_read=137445 bytes_retransmit=0 bytes_invalid=0 send_seq=7302 receive_seq=7302 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999358 adj=49997360 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=214634 bytes_read=6952333 bytes_retransmit=9 bytes_invalid=0 send_seq=30046 receive_seq=30046 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000238 adj=63997738 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=156932 bytes_read=4511716 bytes_retransmit=9 bytes_invalid=0 send_seq=21893 receive_seq=21893 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997514 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=44251 bytes_read=1816333 bytes_retransmit=9 bytes_invalid=0 send_seq=7316 receive_seq=7316 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=44737 bytes_read=134757 bytes_retransmit=9 bytes_invalid=0 send_seq=7303 receive_seq=7303 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.6 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=98829 bytes_read=2757516 bytes_retransmit=0 bytes_invalid=0 send_seq=11862 receive_seq=11862 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998678 coil_temp=16.9 refs=0 mcu_temp=20.32 supply_voltage=3.011 th0: temp=54.4 th1: temp=55.5 th2: temp=61.9 th3: temp=59.3 sysload=0.57 cputime=560.007 memavail=7391904 print_time=7074.794 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 8846.1: gcodein=0  mcu: mcu_awake=0.002 mcu_task_avg=0.000004 mcu_task_stddev=0.000006 bytes_write=35462768 bytes_read=6099704 bytes_retransmit=9 bytes_invalid=0 send_seq=696741 receive_seq=696741 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015854 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=54556 bytes_read=169998 bytes_retransmit=0 bytes_invalid=0 send_seq=9064 receive_seq=9064 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999284 adj=49997327 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=225206 bytes_read=7146310 bytes_retransmit=9 bytes_invalid=0 send_seq=31808 receive_seq=31808 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997671 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=167504 bytes_read=4705692 bytes_retransmit=9 bytes_invalid=0 send_seq=23655 receive_seq=23655 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000046 adj=63997526 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=54844 bytes_read=2260385 bytes_retransmit=9 bytes_invalid=0 send_seq=9079 receive_seq=9079 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997701 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=55309 bytes_read=166641 bytes_retransmit=9 bytes_invalid=0 send_seq=9065 receive_seq=9065 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999443 Octopus_Pro_H723_V1.1: temp=28.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.4 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=109401 bytes_read=3373456 bytes_retransmit=0 bytes_invalid=0 send_seq=13624 receive_seq=13624 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998669 coil_temp=16.9 refs=0 mcu_temp=20.31 supply_voltage=3.011 th0: temp=52.2 th1: temp=53.1 th2: temp=60.4 th3: temp=57.9 sysload=0.06 cputime=636.102 memavail=7392616 print_time=8868.908 buffer_time=0.091 print_stall=0 extruder: target=0 temp=18.5 pwm=0.000 extruder1: target=0 temp=17.5 pwm=0.000
Attempting MCU 'mcu' reset command
Attempting MCU 'rpi' config_reset command
b'Got EOF when reading from device'
Attempting MCU 'toolboard_t0' reset command
Attempting MCU 'toolboard_t1' reset command
Attempting MCU 'dinghy' reset command
Attempting MCU 'plasma' reset command
Attempting MCU 'beacon' reset command
webhooks client 3930049648: Disconnected
Restarting printer
Start printer at Tue Mar 17 03:47:23 2026 (1773719243.1 8847.4)
===== Config file =====
[mcu rpi]
serial = /tmp/klipper_host_mcu

[board_pins btt-octopus-pro-h723-11]
aliases = 
	
	
	
	x_step_pin=PF13,
	x_dir_pin=PF12,
	x_enable_pin=PF14,
	x_uart_pin=PC4,
	x_diag_pin=PG6,
	x_endstop_pin=PG6,
	
	
	
	dual_carriage_step_pin=PF9,
	dual_carriage_dir_pin=PF10,
	dual_carriage_enable_pin=PG2,
	dual_carriage_uart_pin=PF2,
	dual_carriage_diag_pin=PG12,
	dual_carriage_endstop_pin=PG12,
	
	
	
	y_step_pin=PG0,
	y_dir_pin=PG1,
	y_enable_pin=PF15,
	y_uart_pin=PD11,
	y_diag_pin=PG9,
	y_endstop_pin=PG9,
	
	
	
	y1_step_pin=PG4,
	y1_dir_pin=PC1,
	y1_enable_pin=PA2,
	y1_uart_pin=PC7,
	y1_diag_pin=PG11,
	y1_endstop_pin=PG11,
	
	
	
	z0_step_pin=PC13,
	z0_dir_pin=PF0,
	z0_enable_pin=PF1,
	z0_uart_pin=PE4,
	z0_diag_pin=PG13,
	
	
	
	z1_step_pin=PE2,
	z1_dir_pin=PE3,
	z1_enable_pin=PD4,
	z1_uart_pin=PE1,
	z1_diag_pin=PG14,
	
	
	
	z2_step_pin=PE6,
	z2_dir_pin=PA14,
	z2_enable_pin=PE0,
	z2_uart_pin=PD3,
	z2_diag_pin=PG15,
	
	e_step_pin=PF11,
	e_dir_pin=PG3,
	e_enable_pin=PG5,
	e_uart_pin=PC6,
	
	e_heater_pin=PA2,
	e_sensor_pin=PF4,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=PA7,
	stepper_spi_miso_pin=PA6,
	stepper_spi_sclk_pin=PA5,
	adxl345_cs_pin=PA15,
	bltouch_sensor_pin=PB7,
	bltouch_control_pin=PB6,
	probe_pin=PB7,
	fan_part_cooling_pin=PA8,
	fan_toolhead_cooling_pin=PE5,
	fan_controller_board_pin=PD12,
	heater_bed_heating_pin=PA1,
	heater_bed_sensor_pin=PF3,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PG15,
	filament_sensor_motion_pin=PG14,
	ratrig_vaoc_probe_pin=PG10,
	ratrig_vaoc_led_pin=PB0,
	ratrig_vaoc_fan_pin=PD13,
	chamber_lighting_pin=PB11,
	chamber_filter_4p_fan_pin=PD14,
	chamber_filter_4p_fan_enable_pin=PD15

[mcu]
serial = /dev/RatOS/btt-octopus-pro-h723-11

[temperature_sensor Octopus_Pro_H723_V1.1]
sensor_type = temperature_mcu

[adxl345 controlboard]
cs_pin = PA15
spi_software_mosi_pin = PB5
spi_software_miso_pin = PB4
spi_software_sclk_pin = PB3

[board_pins toolboard_t0]
mcu = toolboard_t0
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t0]
serial = /dev/RatOS/btt-ebb42-gen2-10-t0

[temperature_sensor EBB42_Gen2_v1.0_T0]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t0

[lis2dw toolboard_t0]
axes_map = x, z, y
cs_pin = toolboard_t0:PB1
spi_software_mosi_pin = toolboard_t0:PB11
spi_software_miso_pin = toolboard_t0:PB2
spi_software_sclk_pin = toolboard_t0:PB10

[board_pins toolboard_t1]
mcu = toolboard_t1
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t1]
serial = /dev/RatOS/btt-ebb42-gen2-10-t1

[temperature_sensor EBB42_Gen2_v1.0_T1]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t1

[lis2dw toolboard_t1]
axes_map = x, z, y
cs_pin = toolboard_t1:PB1
spi_software_mosi_pin = toolboard_t1:PB11
spi_software_miso_pin = toolboard_t1:PB2
spi_software_sclk_pin = toolboard_t1:PB10

[gcode_macro RatOS]
variable_homing = "endstops"
variable_z_probe = "static"
variable_sensorless_x_current = 0.6
variable_sensorless_y_current = 0.9
variable_safe_home_x = "middle"
variable_safe_home_y = "middle"
variable_driver_type_x = "tmc2209"
variable_driver_type_y = "tmc2209"
variable_stowable_probe_stop_on_error = False
variable_chamber_filter_enable = True
variable_chamber_filter_speed = 0.5
variable_chamber_filter_disable_speed = 1.0
variable_chamber_filter_enable_at = "after_print_start"
variable_chamber_filter_disable_period = 300
variable_chamber_filter_disable_bed_temp = 0
variable_chamber_heater_enable = True
variable_chamber_heater_bed_temp = 115
variable_chamber_heater_preheating_temp = 150
variable_chamber_heater_heating_temp_offset = 25
variable_chamber_heater_control_external_heater = False
variable_chamber_heater_air_circulation_enable = True
variable_chamber_heater_air_circulation_fan_speed = 0.35
variable_chamber_heater_air_circulation_y_pos = 0
variable_chamber_heater_air_circulation_z_pos = 100
variable_chamber_heater_extra_fan_speed = 1.0
variable_chamber_heater_filter_fan_speed = 1.0
variable_bed_heat_soak_time = 0
variable_hotend_heat_soak_time = 0
variable_led_status_action = 0.0,1.0,1.0
variable_led_status_success = 0.0,1.0,0.0
variable_led_status_error = 1.0,0.0,1.0
variable_led_status_on = 1.0,1.0,1.0
variable_led_status_off = 0.0,0.0,1.0
variable_led_status_standby = 0.1,0.1,0.1
variable_led_status_heating = 1.0,0.0,0.0
variable_led_status_cooling = 0.0,0.0,1.0
variable_calibrate_bed_mesh = True
variable_adaptive_mesh = True
variable_start_print_park_in = "center"
variable_start_print_park_z_height = 3
variable_end_print_park_in = "back"
variable_pause_print_park_in = "back"
variable_end_print_park_z_hop = 20
variable_nozzle_priming = "primeblob"
variable_nozzle_prime_start_x = "max"
variable_nozzle_prime_start_y = "min"
variable_nozzle_prime_direction = "auto"
variable_nozzle_prime_bridge_fan = 102
variable_probe_for_priming_result = None
variable_probe_for_priming_end_result = None
variable_probe_for_priming_result_t1 = None
variable_probe_for_priming_end_result_t1 = None
variable_probe_for_priming_disable_mesh_constraints = False
variable_adaptive_prime_offset_threshold = -1.0
variable_last_z_offset = None
variable_runout_park_in = "front"
variable_enable_unload_tip_forming = False
variable_filament_unload_length = 150
description = RatOS variable storage macro, will echo variables to the console when run.
variable_relative_extrusion = True
variable_force_absolute_position = False
variable_preheat_extruder = True
variable_preheat_extruder_temp = 150
variable_macro_travel_speed = 600
variable_macro_travel_accel = 8000
variable_macro_z_speed = 15
variable_bed_margin_x = [59.6, 59.6]
variable_bed_margin_y = [14.35, 33.65]
variable_printable_x_min = 0
variable_printable_x_max = 0
variable_printable_y_min = 0
variable_printable_y_max = 0
variable_end_print_motors_off = True
variable_status_color_ok = "00FF00"
variable_status_color_error = "FF0000"
variable_status_color_unknown = "FFFF00"
variable_end_print_retract_filament = 10
gcode = 
	ECHO_RATOS_VARS
variable_auto_center_subject = False
variable_toolchange_zhop = 2.0
variable_toolchange_zspeed = 25
variable_toolchange_sync_fans = False
variable_toolchange_combined_zhop = False
variable_toolchange_travel_speed = 600
variable_toolchange_travel_accel = 8000
variable_toolchange_extrusion = 2.0
variable_toolchange_retraction = 2.0
variable_toolchange_feedrate = 7200
variable_toolchange_prepurging_timer = 0
variable_toolchange_standby_temp = -1
variable_toolchange_purge = 25
variable_toolchange_first_purge = 50
variable_beacon_bed_mesh_scv = 25
variable_beacon_contact_z_homing = False
variable_beacon_contact_start_print_true_zero = True
variable_beacon_contact_start_print_true_zero_fuzzy_position = True
variable_beacon_contact_calibrate_model_on_true_zero = True
variable_beacon_contact_wipe_before_true_zero = True
variable_beacon_contact_wipe_before_true_zero_method = "probe_clean"
variable_beacon_contact_true_zero_temp = 170
variable_beacon_contact_prime_probing = True
variable_beacon_contact_expansion_compensation = True
variable_beacon_contact_bed_mesh = False
variable_beacon_contact_bed_mesh_samples = 2
variable_beacon_contact_z_tilt_adjust = False
variable_beacon_contact_z_tilt_adjust_samples = 2
variable_beacon_scan_compensation_enable = True
variable_beacon_scan_compensation_profile = "auto"
variable_beacon_scan_compensation_desired_spacing = 10
variable_beacon_scan_compensation_bed_temp_mismatch_is_error = False
variable_beacon_contact_poke_bottom_limit = -1
variable_beacon_scan_method_automatic = False
variable_beacon_adaptive_heat_soak = True
variable_beacon_adaptive_heat_soak_max_wait = 5400
variable_beacon_adaptive_heat_soak_extra_wait_after_completion = 0
variable_beacon_adaptive_heat_soak_layer_quality = 3
variable_beacon_adaptive_heat_soak_maximum_first_layer_duration = 1800
variable_beacon_contact_start_print_true_zero_fuzzy_radius = 20
variable_homing_x = "endstop"
variable_homing_y = "endstop"
variable_default_toolhead = 0
variable_adxl_chip = ["lis2dw toolboard_t0", "lis2dw toolboard_t1"]
variable_shaper_x_freq = [54.2, 53.2, 53.6, 54.7]
variable_shaper_y_freq = [45.0, 47.6, 38.6, 38]
variable_shaper_x_type = ["mzv", "mzv", "mzv", "zv"]
variable_shaper_y_type = ["2hump_ei", "mzv", "mzv", "mzv"]
variable_x_driver_types = ["tmc5160"]
variable_x_axes = ["x"]
variable_y_driver_types = ["tmc5160", "tmc5160"]
variable_y_axes = ["y", "y1"]
variable_z_driver_types = ["tmc2209", "tmc2209", "tmc2209"]
variable_z_axes = ["z", "z1", "z2"]
variable_home_y_first = True

[ratos_homing]
axes = xyz
z_hop = 15
z_hop_speed = 15
gcode = 
	
	_LED_ON
	
	
	{% set prev_stop_on_error = printer["gcode_macro RatOS"].stowable_probe_stop_on_error %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set target_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	_IDEX_SINGLE
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE=True
	
	
	M400
	
	G90
	
	
	{% set X = true if params.X is defined else false %}
	{% set Y = true if params.Y is defined else false %}
	{% set Z = true if params.Z is defined else false %}
	{% if printer["gcode_macro RatOS"].home_y_first|default(false)|lower == 'true' %}
	HOME_Y X={X} Y={Y} Z={Z}
	HOME_X X={X} Y={Y} Z={Z}
	{% else %}
	HOME_X X={X} Y={Y} Z={Z}
	HOME_Y X={X} Y={Y} Z={Z}
	{% endif %}
	HOME_Z X={X} Y={Y} Z={Z}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE={prev_stop_on_error}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[gcode_macro HOME_X]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_x = printer["gcode_macro RatOS"].homing_x|lower %}
	{% set homing_x = homing_x if homing_x else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_X" MSG="printable_x_max: {printable_x_max}, safe_home_x: {safe_home_x}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}"
	
	
	{% if X or not Y and not Z %}
	{% if homing_x == 'endstop' %}
	G28 X
	{% elif homing_x == 'sensorless' %}
	{% if printer["dual_carriage"] is defined %}
	{ action_emergency_stop("sensorless homing not supported on IDEX!") }
	{% endif %}
	HOME_X_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_x to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_x, homing)) }
	{% endif %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1} MODE=PRIMARY
	G1 X{parking_position} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	{% endif %}
	{% set x_homed = True %}
	G0 X{safe_home_x} F{speed}
	M400
	{% endif %}

[gcode_macro HOME_Y]
gcode = 
	
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_y = printer["gcode_macro RatOS"].homing_y|lower %}
	{% set homing_y = homing_y if homing_y else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Y" MSG="printable_y_max: {printable_y_max}, safe_home_y: {safe_home_y}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}"
	
	
	{% if Y or not X and not Z %}
	{% if homing_y == 'endstop' %}
	G28 Y
	{% elif homing_y == 'sensorless' %}
	HOME_Y_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_y to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_y, homing)) }
	{% endif %}
	{% set y_homed = True %}
	G0 Y{safe_home_y} F{speed}
	{% endif %}

[gcode_macro HOME_Z]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	
	
	{% set beacon_contact_z_homing = true if printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_z_home_position_fuzzing_radius = printer["gcode_macro RatOS"].beacon_z_home_position_fuzzing_radius|default(0)|float %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Z" MSG="x_homed: {x_homed}, y_homed: {y_homed}, z_probe: {z_probe}, beacon_contact_z_homing: {beacon_contact_z_homing}"
	
	
	{% if Z or not Y and not X %}
	RATOS_ECHO MSG="Homing Z"
	{% if x_homed == False or y_homed == False %}
	{ action_emergency_stop("X and Y must be homed before homing Z") }
	{% else %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_homing %}
	{% if beacon_contact_start_print_true_zero %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% else %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	{% else %}
	G28 Z
	{% endif %}
	_Z_HOP
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro HOME_X_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	
	G4 P300
	
	G28 X
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"

[gcode_macro HOME_Y_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	
	G4 P300
	
	G28 Y
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"

[gcode_macro _Z_HOP]
description = Move Z axis up by Z_HOP distance at Z_HOP_SPEED. In relative mode it will move Z axis up by Z_HOP distance. In absolute mode it will move Z axis to Z_HOP distance.
gcode = 
	{% set z_hop = printer.fastconfig.config.ratos_homing.z_hop|float %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	G0 Z{z_hop} F{z_hop_speed}

[gcode_macro __MOVE_TO_SAFE_Z_HOME_ECHO_DEBUG]
gcode = 
	DEBUG_ECHO PREFIX="_MOVE_TO_SAFE_Z_HOME" MSG="x: {params.X}, y: {params.Y}, z_hop: {params.Z_HOP}, fuzzy_radius: {params.FUZZY_RADIUS}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}, printable_x_max: {printer['gcode_macro RatOS'].printable_x_max}, printable_y_max: {printer['gcode_macro RatOS'].printable_y_max}"

[gcode_macro MAYBE_HOME]
description = Only home unhomed axis. Specify ABL=1 to also ensure that automatic bed levelling is applied (if configured).
variable_is_kinematic_position_overriden = False
gcode = 
	{% set abl = params.ABL|default('')|lower in ('true', 'yes', '1') %}
	{% if printer["gcode_macro MAYBE_HOME"].is_kinematic_position_overriden|lower == 'true' %}
	RATOS_ECHO MSG="SET_CENTER_KINEMATIC_POSITION has been abused. Homing all axes. Please refrain from using SET_CENTER_KINEMATIC_POSITION outside of debugging purposes."
	G28
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=False
	{% else %}
	{% set axes = '' %}
	{% set isHomed = true %}
	{% set axesToHome = '' %}
	{% if params.X is defined %}
	{% set axes = axes ~ 'X ' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% endif %}
	{% if params.Y is defined %}
	{% set axes = axes ~ 'Y ' %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% endif %}
	{% if params.Z is defined %}
	{% set axes = axes ~ 'Z ' %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if params.X is not defined and params.Y is not defined and params.Z is not defined %}
	{% set axes = '' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if isHomed is false %}
	RATOS_ECHO MSG="Homing {axesToHome}"
	G28 {axesToHome}
	{% else %}
	RATOS_ECHO MSG="All requested axes already homed. Skipping homing."
	{% endif %}
	{% endif %}
	{% if abl %}
	{% if printer.z_tilt is defined %}
	{% if not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Performing Z tilt adjustment..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Z tilt already applied. Skipping Z tilt adjustment."
	{% endif %}
	{% elif printer.quad_gantry_level is defined %}
	{% if not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Performing quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Quad gantry leveling already applied. Skipping quad gantry leveling."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="No automatic bed leveling method configured. Skipping bed leveling."
	{% endif %}
	{% endif %}

[gcode_macro PID_CALIBRATE_HOTEND]
description = Perform a PID calibration test for a given extruder heater.
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set temp = params.TEMP|default(220)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_HOTEND" MSG="TEMP={temp}"
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO MSG="PID calibration hotend heater T0 at {temp}°C..."
	PID_CALIBRATE HEATER=extruder TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	
	{% if toolhead==0 or toolhead==1 %}
	RATOS_ECHO MSG="PID calibration hotend heater T{toolhead} at {temp}°C..."
	PID_CALIBRATE HEATER=extruder{'' if toolhead==0 else toolhead} TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_BED]
description = Perform a PID calibration test for the bed heater.
gcode = 
	
	{% set temp = params.TEMP|default(80)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_BED" MSG="TEMP={temp}"
	RATOS_ECHO MSG="PID calibration bed heater at {temp}°C..."
	
	
	PID_CALIBRATE HEATER=heater_bed TARGET={temp}
	
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_CHAMBER_HEATER]
description = Perform a PID calibration test for the chamber heater.
gcode = 
	
	{% set temp = params.TEMP|default(150)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_CHAMBER_HEATER" MSG="TEMP={temp}"
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	RATOS_ECHO MSG="PID calibration chamber heater at {temp}°C..."
	PID_CALIBRATE HEATER=chamber_heater TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_heater" %}
	{% set link_text = "RatOS Chamber Heater" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber heater found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro INITIALIZE_PA_TUNING]
description = Start a pressure advance tuning tower.
gcode = 
	
	{% set start = params.START|default(0.0)|float %}
	{% set factor = params.FACTOR|default(0.001)|float %}
	
	
	{% set layer_number = printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|default(0)|int %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if is_printing_gcode and layer_number < 2 %}
	DEBUG_ECHO PREFIX="START_PA_TOWER" MSG="START: {start}, FACTOR: {factor}"
	RATOS_ECHO MSG="Starting pressure advance tuning tower..."
	TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START={start} FACTOR={factor}
	{% else %}
	RATOS_ECHO MSG="Pressure advance tuning tower requires you to be printing gcode and on layer 1 to start."
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro CHAMBER_FILTER_ON]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	_CHAMBER_FILTER_TURN_ON
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro CHAMBER_FILTER_OFF]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Deactivating chamber filter..."
	_CHAMBER_FILTER_TURN_OFF
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set chamber_filter_enable_at = printer["gcode_macro RatOS"].chamber_filter_enable_at|default('after_print_start')|lower %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_ON" MSG="at: {at}, chamber_filter_enable: {chamber_filter_enable}, chamber_filter_enable_at: {chamber_filter_enable_at}, chamber_filter_speed: {chamber_filter_speed}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	{% if chamber_filter_enable_at == at %}
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	
	
	_CHAMBER_FILTER_TURN_ON AT={at}
	
	
	{% if chamber_filter_enable_at == "print_end" %}
	_LED_CHAMBER_FILTER_ON
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_OFF]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF" MSG="chamber_filter_enable: {chamber_filter_enable}, filter_disable_period: {filter_disable_period}, filter_disable_bed_temp: {filter_disable_bed_temp}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	
	{% if filter_disable_period > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting {filter_disable_period} seconds before turning chamber filter off..."
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION={filter_disable_period}
	{% endif %}
	
	
	{% if filter_disable_bed_temp > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting for bed temp to cool down to {filter_disable_bed_temp}°C to turn filter off..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM=0 MAXIMUM={filter_disable_bed_temp}
	_CHAMBER_FILTER_TURN_OFF
	_LED_CHAMBER_FILTER_OFF
	{% endif %}
	
	{% endif %}

[delayed_gcode _CHAMBER_FILTER_OFF_TIMER]
gcode = 
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF_TIMER" MSG="executed"
	
	
	_CHAMBER_FILTER_TURN_OFF
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Chamber filter turned off!"
	
	
	_LED_CHAMBER_FILTER_OFF

[gcode_macro _CHAMBER_FILTER_TURN_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_speed|default(0)|float %}
	{% if at == "print_end" %}
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_disable_speed|default(0)|float %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION=0
	
	
	SET_FAN_SPEED FAN=filter SPEED={chamber_filter_speed}

[gcode_macro _CHAMBER_FILTER_TURN_OFF]
gcode = 
	
	SET_FAN_SPEED FAN=filter SPEED=0

[gcode_macro _CHAMBER_FILTER_SANITY_CHECK]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	{% if filter_disable_bed_temp > 0 and filter_disable_period > 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable, not both.")}
	{% endif %}
	
	{% if filter_disable_bed_temp == 0 and filter_disable_period == 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable.")}
	{% endif %}
	
	{% endif %}

[gcode_macro CHAMBER_HEATER_ON]
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(45)|int %}
	
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp} IS_FROM_START_PRINT=False

[gcode_macro CHAMBER_HEATER_OFF]
gcode = 
	_CHAMBER_HEATER_OFF

[gcode_macro _CHAMBER_HEATER_ON]
variable_chamber_temp = 0
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	{% set is_from_start_print = true if params.IS_FROM_START_PRINT|default(True)|lower == 'true' else false %}
	
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set chamber_heater_enable = true if printer["gcode_macro RatOS"].chamber_heater_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}
	{% set chamber_heater_preheating_temp = printer["gcode_macro RatOS"].chamber_heater_preheating_temp|default(150)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	{% set chamber_heater_control_external_heater = true if printer["gcode_macro RatOS"].chamber_heater_control_external_heater|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_enable = true if printer["gcode_macro RatOS"].chamber_heater_air_circulation_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_fan_speed = printer["gcode_macro RatOS"].chamber_heater_air_circulation_fan_speed|default(0.35)|float %}
	{% set chamber_heater_air_circulation_y_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_y_pos|default(0)|float %}
	{% set chamber_heater_air_circulation_z_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_z_pos|default(100)|float %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_HEATER_ON" MSG="chamber_heater_enable: {chamber_heater_enable}, chamber_heater_preheating_temp: {chamber_heater_preheating_temp}, chamber_heater_heating_temp_offset: {chamber_heater_heating_temp_offset}, bed_temp: {bed_temp}, chamber_temp: {chamber_temp}, start_chamber_temp: {start_chamber_temp}"
	
	
	{% if chamber_heater_enable and chamber_temp > 0 and chamber_heater_bed_temp > 0 %}
	
	
	_LED_HEATING
	
	
	RATOS_ECHO MSG="Preheating chamber to {(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}°C..."
	
	
	{% set chamber_temp_sensor = "extruder" %}
	{% if printer["dual_carriage"] is defined and default_toolhead == 1 %}
	{% set chamber_temp_sensor = "extruder1" %}
	{% endif %}
	{% if printer["temperature_sensor chamber"] is defined %}
	{% set chamber_temp_sensor = "temperature_sensor chamber" %}
	{% endif %}
	
	
	{% set current_chamber_temp = printer['%s' % chamber_temp_sensor].temperature|int %}
	
	
	{% set needs_heating = current_chamber_temp < (start_chamber_temp if start_chamber_temp > 0 else chamber_temp) %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_BEFORE_PREHEATING
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	{% if not is_from_start_print %}
	MAYBE_HOME
	{% endif %}
	G0 Z{chamber_heater_air_circulation_z_pos} F{z_speed}
	G0 Y{chamber_heater_air_circulation_y_pos} F{speed}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * chamber_heater_air_circulation_fan_speed)}
	{% endif %}
	{% else %}
	{% if is_from_start_print %}
	G0 Z{z} F{z_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE={chamber_temp}
	
	
	{% if needs_heating %}
	
	
	M140 S{chamber_heater_bed_temp}
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={chamber_heater_preheating_temp}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	
	{% endif %}
	
	
	{% if needs_heating %}
	_CHAMBER_HEATER_EXTRA_FAN_ON
	{% endif %}
	
	
	{% if needs_heating %}
	TEMPERATURE_WAIT SENSOR="{chamber_temp_sensor}" MINIMUM={(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% endif %}
	
	
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED=0
	_CHAMBER_FILTER_ON AT="before_print_start"
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	G28 Z
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_AFTER_PREHEATING
	{% endif %}
	
	
	{% if printer["temperature_sensor chamber"] is defined %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined and chamber_heater_control_external_heater %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	
	
	_LED_SUCCESS
	
	{% endif %}

[gcode_macro _CHAMBER_HEATER_OFF]
gcode = 
	RATOS_ECHO MSG="Deactivating chamber heater..."
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=0
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE=0
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	
	
	_CHAMBER_HEATER_EXTRA_FAN_OFF

[delayed_gcode _CHAMBER_HEATER_CONTROL]
initial_duration = 0.
gcode = 
	
	{% set chamber_temp = printer["gcode_macro _CHAMBER_HEATER_ON"].chamber_temp|default(0)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	
	
	{% set current_chamber_temp = printer['temperature_sensor chamber'].temperature|int %}
	
	
	{% if current_chamber_temp < chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	{% endif %}
	
	
	{% if current_chamber_temp >= chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_ON]
gcode = 
	
	{% set chamber_heater_extra_fan_speed = printer["gcode_macro RatOS"].chamber_heater_extra_fan_speed|default(0.0)|float %}
	
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	{% if chamber_heater_extra_fan_speed > 0 %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED={chamber_heater_extra_fan_speed}
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_OFF]
gcode = 
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED=0
	{% endif %}

[gcode_macro _USER_CHAMBER_HEATER_BEFORE_PREHEATING]
description = Will be executed before chamber preheating, only if heating is needed.
gcode = 

[gcode_macro _USER_CHAMBER_HEATER_AFTER_PREHEATING]
description = Will be executed after chamber preheating, only if heating was needed.
gcode = 

[gcode_macro RESET_HEATSOAK_SETTINGS]
description = Resets all heatsoak-related settings to startup defaults
gcode = 
	HEATSOAK_SETTINGS ACTION=reset

[gcode_macro USE_ADAPTIVE_HEATSOAK]
description = Temporarily enables adaptive bed heatsoaking (if a beacon probe is present), will reset to printer.cfg settings
	when Klipper is restarted. Optionally specify QUALITY (1-5) and maximum FIRST_LAYER_DURATION (in minutes).
	Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.QUALITY|default("1..5") %}
	{% set _ = params.FIRST_LAYER_DURATION|default("1..120 minutes") %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("Adaptive heatsoaking is only available when a beacon probe is configured.") }
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_quality = (settings.variable_beacon_adaptive_heat_soak_layer_quality if defsrc == 'startup' else current.beacon_adaptive_heat_soak_layer_quality)|default(3)|int %}
	{% set default_first_layer_duration_secs = (settings.variable_beacon_adaptive_heat_soak_maximum_first_layer_duration if defsrc == 'startup' else current.beacon_adaptive_heat_soak_maximum_first_layer_duration)|default(1800)|int %}
	{% if params2.QUALITY is defined %}
	{% set quality = params2.QUALITY|int %}
	{% if quality < 1 or quality > 5 %}
	{ action_raise_error("QUALITY must be between 1 (rough) and 5 (maximum). Use 3 (normal) if unsure.") }
	{% endif %}
	{% else %}
	{% set quality = default_quality %}
	{% endif %}
	{% if params2.FIRST_LAYER_DURATION is defined %}
	{% set first_layer_duration_mins = params2.FIRST_LAYER_DURATION|float %}
	{% if first_layer_duration_mins <= 0 %}
	{ action_raise_error("FIRST_LAYER_DURATION must be a positive number specifying the maximum first layer duration in minutes.") }
	{% endif %}
	{% if first_layer_duration_mins > 120 %}
	CONSOLE_ECHO MSG="FIRST_LAYER_DURATION will be limited to 120 minutes. Values larger than this will not have an effect on soak time."
	{% set first_layer_duration_mins = 120 %}
	{% endif %}
	{% set first_layer_duration_secs = (first_layer_duration_mins * 60.0)|int %}
	{% else %}
	{% set first_layer_duration_secs = default_first_layer_duration_secs %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	{% endif %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=True beacon_adaptive_heat_soak_layer_quality={quality} beacon_adaptive_heat_soak_maximum_first_layer_duration={first_layer_duration_secs}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."

[gcode_macro USE_FIXED_HEATSOAK]
description = Temporarily enables fixed bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
	Optionally specify DURATION (in minutes). Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.DURATION|default("0..720 minutes") %}
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_duration = (settings.variable_bed_heat_soak_time if defsrc == 'startup' else current.bed_heat_soak_time)|default(0)|int %}
	{% if params2.DURATION is defined %}
	{% set duration_mins = params2.DURATION|float %}
	{% if duration_mins < 0 %}
	{ action_raise_error("DURATION must be a non-negative number specifying the heatsoak duration in minutes.") }
	{% endif %}
	{% if duration_mins > 720 %}
	CONSOLE_ECHO MSG="DURATION will be limited to 720 minutes (12 hours). If you really need a larger value, adjust printer.cfg instead."
	{% set duration_mins = 720 %}
	{% endif %}
	{% set duration_secs = (duration_mins * 60.0)|int %}
	{% else %}
	{% set duration_secs = default_duration %}
	{% set duration_mins = duration_secs / 60.0 %}
	{% endif %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% if has_beacon %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=False bed_heat_soak_time={duration_secs}
	{% else %}
	HEATSOAK_SETTINGS QUIET=1 bed_heat_soak_time={duration_secs}
	{% endif %}
	{% if duration_mins < 1e-3 %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% else %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% endif %}

[gcode_macro USE_NO_HEATSOAK]
description = Temporarily disables bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
gcode = 
	USE_FIXED_HEATSOAK DURATION=0

[gcode_macro HEATSOAK_SETTINGS]
description = Shows or adjusts heatsoak settings
	- With no arguments: shows current heatsoak settings, specify VERBOSE=1 for detailed output
	- With arguments: sets the specified settings. Use the full setting name without the variable_ prefix, e.g. bed_heat_soak_time=300 or beacon_adaptive_heat_soak_layer_quality=4. See printer.cfg for available settings.
variable_default_source = "startup"
gcode = 
	
	{% set params2 = params %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% set quiet = params2.pop("QUIET", None)|default("0") in ("1", "true", "yes") %}
	{% set verbose = params2.pop("VERBOSE", None)|default("0") in ("1", "true", "yes") %}
	{% if has_beacon %}
	{% set vars = (
	"beacon_adaptive_heat_soak",
	"beacon_adaptive_heat_soak_max_wait",
	"beacon_adaptive_heat_soak_extra_wait_after_completion",
	"beacon_adaptive_heat_soak_layer_quality",
	"beacon_adaptive_heat_soak_maximum_first_layer_duration",
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% else %}
	{% set vars = (
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% endif %}
	{% set action = "show" if params|length == 0 else params2.ACTION %}
	{% if action is defined and params|length > 1 %}
	{ action_raise_error("ACTION cannot be specified with other parameters.") }
	{% elif action is not defined %}
	{% for k, v in params2.items() %}
	{% set k = k|lower %}
	{% if k in vars %}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Setting {k} to {v}"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={k} VALUE={v}
	{% else %}
	{ action_raise_error("Parameter '%s' is not recognised. Note that adaptive heatsoaking settings can only be set when a beacon probe is configured." % k) }
	{% endif %}
	{% endfor %}
	{% elif action == "reset" %}
	_RESET_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	CONSOLE_ECHO MSG="Heatsoak settings have been reset to their original values."
	{% elif action == "show" %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% set is_adaptive = False if not has_beacon else current.beacon_adaptive_heat_soak|default("")|lower == "true" %}
	{% if is_adaptive %}
	{% set quality = current.beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set first_layer_duration_secs = current.beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."
	{% elif current.bed_heat_soak_time|default(0)|int > 0 %}
	{% set duration_mins = (current.bed_heat_soak_time|int / 60.0) %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% else %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% endif %}
	{% if verbose %}
	CONSOLE_ECHO MSG="Detailed settings:"
	_SHOW_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	{% endif %}
	{% else %}
	{ action_raise_error("Action '%s' is not recognised" % action) }
	{% endif %}

[gcode_macro _LED_START_PRINTING]
gcode = 
	_LED_ACTION

[gcode_macro _LED_START_PRINTING_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_PRINTING]
gcode = 
	_LED_ON TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_PAUSE]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_ON]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_OFF]
gcode = 
	_LED_STANDBY

[gcode_macro _LED_LOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_LOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_RUNOUT]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_CLOG]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_UNLOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_UNLOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_DEACTIVATE_TOOLHEAD]
gcode = 
	_LED_OFF TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_STANDBY]
gcode = 
	_LED_STANDBY TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_WAKEUP]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_MOTORS_OFF]
gcode = 
	_LED_STANDBY
	_LED_VAOC_OFF

[gcode_macro _LED_INPUT_SHAPER_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_INPUT_SHAPER_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_BEACON_CALIBRATION_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_VAOC_ON]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=1.0 GREEN=1.0 BLUE=1.0
	{% endif %}

[gcode_macro _LED_VAOC_OFF]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=0.0 GREEN=0.0 BLUE=0.0
	{% endif %}

[gcode_macro _LED_ACTION]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_action %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SUCCESS]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_success %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_HEATING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_heating %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_COOLING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_cooling %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ERROR]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_error %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ON]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_on %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_OFF]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_off %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_STANDBY]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_standby %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}
	
	{% if toolhead >= 0 %}
	{% if printer['neopixel nozzle_led_t%s' % toolhead] is defined  %}
	SET_LED LED={'nozzle_led_t%s' % toolhead} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% else %}
	{% if printer['neopixel nozzle_led_t0'] is defined  %}
	SET_LED LED={'nozzle_led_t0'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% if printer['neopixel nozzle_led_t1'] is defined %}
	SET_LED LED={'nozzle_led_t1'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% endif %}
	
	_USER_LED_SET { rawparams }

[gcode_macro _USER_LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}

[gcode_macro LOAD_FILAMENT]
description = Loads new filament. Note: be careful with PETG, make sure you inspect the tip of your filament before loading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% if filament_name == '' or filament_type == '' %}
	{% set filament_name = 'unknown' %}
	{% set filament_type = 'unknown' %}
	{% endif %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_LOAD_FILAMENT TEMP={temp} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_LOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_LOAD_FILAMENT]
description = Load filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_LOAD_FILAMENT" MSG="TEMP={temp}"
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=load_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	_LOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	
	
	RESTORE_GCODE_STATE NAME=load_state
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament load routine complete, please check that the filament was loaded correctly."

[gcode_macro _IDEX_LOAD_FILAMENT]
description = Load filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament into T{toolhead}..."
	
	DEBUG_ECHO PREFIX="_IDEX_LOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	_LOAD_FILAMENT TOOLHEAD={toolhead} TEMP={temp} AUTOMATED={automated}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="Filament load routine for T{toolhead} complete, please check that the filament was loaded correctly."

[gcode_macro _LOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default(false)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE TOOLHEAD={toolhead}
	_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into hotend.."
	G92 E0
	G0 E{extruder_gear_to_cooling_position_distance} F{extruder_load_speed}
	G92 E0
	M400
	RATOS_ECHO MSG="Filament loaded into hotend."

[gcode_macro _LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set load_speed = printer["gcode_macro T%s" % toolhead].filament_load_speed|float * 60 %}
	{% set filament_loading_nozzle_offset = printer["gcode_macro T%s" % toolhead].filament_loading_nozzle_offset|float %}
	{% set cooling_position_to_nozzle_distance = printer["gcode_macro T%s" % toolhead].cooling_position_to_nozzle_distance|float %}
	{% set purge_after_load = printer["gcode_macro T%s" % toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into nozzle... Please wait!"
	G92 E0
	
	G0 E{cooling_position_to_nozzle_distance + filament_loading_nozzle_offset} F{load_speed}
	G92 E0
	G4 P1000
	_PURGE_FILAMENT	TOOLHEAD={toolhead} E={purge_after_load}
	RATOS_ECHO MSG="Filament loaded into nozzle!"

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"
	
	
	{% set filament_grabbing_length = printer["gcode_macro T%s" % toolhead].filament_grabbing_length|float %}
	{% set filament_grabbing_speed = printer["gcode_macro T%s" % toolhead].filament_grabbing_speed|float %}
	{% set resume_after_insert = true if printer["gcode_macro T%s" % toolhead].resume_after_insert|default(true)|lower == 'true' else false %}
	{% set enable_insert_detection = true if printer["gcode_macro T%s" % toolhead].enable_insert_detection|default(true)|lower == 'true' else false %}
	
	
	{% set current_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	
	{% if enable_insert_detection %}
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="toolhead: {toolhead}, filament_grabbing_length: {filament_grabbing_length}, filament_grabbing_speed: {filament_grabbing_speed}, current_idex_mode: {current_idex_mode}"
	
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	RATOS_ECHO MSG="Filament inserted into T{toolhead}, loading..."
	
	
	FORCE_MOVE STEPPER={'extruder%s' % ('' if toolhead == 0 else toolhead)} DISTANCE={filament_grabbing_length} VELOCITY={filament_grabbing_speed}
	M400
	
	
	{% if printer.pause_resume.is_paused %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% if resume_after_insert %}
	RESUME
	{% endif %}
	{% else %}
	{% if not printer.virtual_sdcard.is_active %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"

[gcode_macro _PURGE_BEFORE_UNLOAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set purge_before_unload = printer["gcode_macro T%s" % toolhead].purge_before_unload|float %}
	
	DEBUG_ECHO PREFIX="_PURGE_BEFORE_UNLOAD" MSG="TOOLHEAD: {toolhead}"
	
	
	{% if purge_before_unload > 0 %}
	G92 E0
	G0 E{purge_before_unload} F300
	G92 E0
	M400
	{% endif %}

[gcode_macro _PURGE_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set e = params.E|int %}
	{% set r = params.R|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_PURGE_FILAMENT" MSG="TOOLHEAD: {toolhead}, E: {e}"
	
	
	{% if e > 0 %}
	
	
	G92 E0
	G0 E{e} F300
	G92 E0
	M400
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={0.4 if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={0.4 if toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * 0.4)}
	{% endif %}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if r > 0 %}
	G92 E0
	G0 E-{r} F300
	G92 E0
	M400
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro _MOVE_TO_LOADING_POSITION]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_MOVE_TO_LOADING_POSITION" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	
	G1 X{loading_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _CLEANING_MOVE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_CLEANING_MOVE" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].parking_position is defined and printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set parking_position = printer["gcode_macro T%s" % toolhead].parking_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	{% set cleaning_position = loading_position %}
	{% if loading_position == parking_position %}
	{% if loading_position > 0 %}
	{% set cleaning_position = loading_position - 30 %}
	{% else %}
	{% set cleaning_position = loading_position + 30 %}
	{% endif %}
	{% endif %}
	
	
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _BED_MESH_SANITY_CHECK]
gcode = 
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is defined %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_start_print_true_zero_fuzzy_position %}
	CONSOLE_ECHO TYPE="error" TITLE="Defined zero reference not compatible with fuzzy true zero" MSG="Using fuzzy start print true zero position is not compatible with a defined zero_reference_position value in the [bed_mesh] section in printer.cfg._N_Please remove the zero_reference_position value from the [bed_mesh] section, or disable fuzzy true zero position in printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_start_print_true_zero_fuzzy_position: False"
	_STOP_AND_RAISE_ERROR MSG="Defined zero reference not compatible with fuzzy true zero"
	{% elif zero_ref_pos[0]|float|round != safe_home_x|float|round or zero_ref_pos[1]|float|round != safe_home_y|float|round %}
	CONSOLE_ECHO TYPE="error" TITLE="Zero reference position does not match safe home position" MSG="Please update your bed mesh zero reference position in printer.cfg, like so:_N__N_[bed_mesh]_N_zero_reference_position: {safe_home_x|float|round},{safe_home_y|float|round}_N_"
	_STOP_AND_RAISE_ERROR MSG="Zero reference position does not match safe home position"
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_bed_mesh %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact bed mesh is enabled" MSG="Beacon contact bed mesh is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_bed_mesh: False"
	{% endif %}
	
	{% if beacon_scan_method_automatic %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon 'automatic' scan method is enabled" MSG="Beacon 'automatic' scan method is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_scan_method_automatic: False"
	{% endif %}
	
	{% if beacon_contact_z_tilt_adjust %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact z-tilt adjust is enabled" MSG="Beacon contact z-tilt adjust is enabled. This is not recommended for normal use and may result in inaccurate z-tilt adjustment._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_z_tilt_adjust: False"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH]
gcode = 
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE=None
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE=None
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION {rawparams}
	{% endif %}

[gcode_macro _START_PRINT_BED_MESH]
variable_actual_true_zero_position_x = None
variable_actual_true_zero_position_y = None
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set X=[params.X0|default(-1)|float, params.X1|default(-1)|float] %}
	{% set Y=[params.Y0|default(-1)|float, params.Y1|default(-1)|float] %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_BED_MESH" MSG="idex_mode: {idex_mode}, X: {X}, Y: {Y}"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is not defined %}
	{% set zero_ref_pos = [safe_home_x if actual_true_zero_position_x is none else actual_true_zero_position_x, safe_home_y if actual_true_zero_position_y is none else actual_true_zero_position_y] %}
	{% endif %}
	
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	
	
	
	
	{% set X=[0, printable_x_max] %}
	{% endif %}
	
	
	{% set beacon_bed_mesh_scv = printer["gcode_macro RatOS"].beacon_bed_mesh_scv|default(25)|int %}
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% if printer.fastconfig.settings.beacon is defined and not beacon_contact_bed_mesh %}
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={beacon_bed_mesh_scv}
	{% endif %}
	
	
	{% set default_profile = printer["gcode_macro RatOS"].bed_mesh_profile|default('ratos') %}
	{% if printer["gcode_macro RatOS"].calibrate_bed_mesh|lower == 'true' %}
	BED_MESH_CLEAR
	{% if printer["gcode_macro RatOS"].adaptive_mesh|lower == 'true' %}
	CALIBRATE_ADAPTIVE_MESH PROFILE="{default_profile}" X0={X[0]} X1={X[1]} Y0={Y[0]} Y1={Y[1]} T={params.T|int} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={idex_mode} ZERO_REF_POS_X={zero_ref_pos[0]} ZERO_REF_POS_Y={zero_ref_pos[1]}
	{% else %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	BED_MESH_PROFILE LOAD="{default_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	
	{% elif printer["gcode_macro RatOS"].bed_mesh_profile is defined %}
	BED_MESH_CLEAR
	BED_MESH_PROFILE LOAD="{printer["gcode_macro RatOS"].bed_mesh_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"

[gcode_macro CALIBRATE_ADAPTIVE_MESH]
gcode = 
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set default_profile = params.PROFILE %}
	
	
	{% set x0 = params.X0|default(-1)|float %}
	{% set y0 = params.Y0|default(-1)|float %}
	{% set x1 = params.X1|default(-1)|float %}
	{% set y1 = params.Y1|default(-1)|float %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Received coordinates X0={x0|round(1)} Y0={y0|round(1)} X1={x1|round(1)} Y1={y1|round(1)}"
	
	{% if x0 >= x1 or y0 >= y1 %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Invalid coordinates received. Please check your slicer settings. Falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	
	
	{% if params.ZERO_REF_POS_X is defined and params.ZERO_REF_POS_Y is defined %}
	{% set zero_ref_pos_x = params.ZERO_REF_POS_X|float %}
	{% set zero_ref_pos_y = params.ZERO_REF_POS_Y|float %}
	{% if zero_ref_pos_x < x0 or zero_ref_pos_x > x1 or zero_ref_pos_y < y0 or zero_ref_pos_y > y1 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Zero reference position X={zero_ref_pos_x|round(1)} Y={zero_ref_pos_y|round(1)} is outside the mesh region, expanding mesh region to include it."
	{% set x0 = [x0, zero_ref_pos_x]|min %}
	{% set y0 = [y0, zero_ref_pos_y]|min %}
	{% set x1 = [x1, zero_ref_pos_x]|max %}
	{% set y1 = [y1, zero_ref_pos_y]|max %}
	{% endif %}
	{% endif %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float %}
	
	
	{% set mesh_x0 = [[x0, max_x]|min, min_x]|max %}
	{% set mesh_y0 = [[y0, max_y]|min, min_y]|max %}
	{% set mesh_x1 = [[x1, max_x]|min, min_x]|max %}
	{% set mesh_y1 = [[y1, max_y]|min, min_y]|max %}
	
	{% if mesh_x0 == min_x and mesh_y0 == min_y and mesh_x1 == max_x and mesh_y1 == max_y %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Print is using the full bed, falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	
	{% set probe_count_x = mesh_config.probe_count.split(",")[0]|int %}
	{% if mesh_config.probe_count.split(",")|length == 2 %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[1]|int %}
	{% else %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[0]|int %}
	{% endif %}
	
	
	{% set probe_x_step = (max_x - min_x) / probe_count_x %}
	{% set probe_y_step = (max_y - min_y) / probe_count_y %}
	
	
	{% set mesh_count_x = ([(mesh_x1 - mesh_x0) / probe_x_step, 3]|max)|int %}
	{% set mesh_count_y = ([(mesh_y1 - mesh_y0) / probe_y_step, 3]|max)|int %}
	{% set min_mesh_count = [mesh_count_x, mesh_count_y]|min %}
	{% set max_mesh_count = [mesh_count_x, mesh_count_y]|max %}
	
	
	{% set algorithm = mesh_config.algorithm %}
	{% if algorithm|lower == 'lagrange' and max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="cannot exceed a probe_count of 6 when using lagrange interpolation. Falling back to bicubic interpolation."
	{% set algorithm = 'bicubic' %}
	{% endif %}
	{% if algorithm|lower == 'bicubic' and min_mesh_count < 4 %}
	{% if max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="invalid probe_count option when using bicubic interpolation. Combination of 3 points on one axis with more than 6 on another is not permitted. Forcing minimum mesh count to be 4."
	{% set min_mesh_count = 4 %}
	{% else %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="bicubic interpolation with a probe_count of less than 4 points detected. Forcing lagrange interpolation."
	{% set algorithm = 'lagrange' %}
	{% endif %}
	{% endif %}
	
	{% set mesh_count_x = ([min_mesh_count, mesh_count_x]|max)|int %}
	{% set mesh_count_x = ([max_mesh_count, mesh_count_x]|min)|int %}
	{% set mesh_count_y = ([min_mesh_count, mesh_count_y]|max)|int %}
	{% set mesh_count_y = ([max_mesh_count, mesh_count_y]|min)|int %}
	
	{% set should_prime = printer["gcode_macro RatOS"].nozzle_priming == 'primeblob' %}
	{% if printer["dual_carriage"] is not defined %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% else %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 != 0 and probe_first %}
	{% set probe_first = false %}
	{% elif printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 == 0 and not probe_first %}
	{% set probe_first = true %}
	{% endif %}
	
	
	{% if should_prime and probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="mesh coordinates X0={mesh_x0|round(1)} Y0={mesh_y0|round(1)} X1={mesh_x1|round(1)} Y1={mesh_y1|round(1)}"
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y} RELATIVE_REFERENCE_INDEX=-1
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	
	
	{% if should_prime and not probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro M84]
rename_existing = M84.1
gcode = 
	
	M84.1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_OFFSET X=0 Y=0
	
	
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro _VAOC"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False
	{% endif %}
	
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	SET_SKEW CLEAR=1
	
	
	_LED_MOTORS_OFF

[gcode_macro M104]
rename_existing = M104.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M104" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set temperature_offset_t0 = printer["gcode_macro T0"].temperature_offset|default(0)|int %}
	{% set temperature_offset_t1 = printer["gcode_macro T1"].temperature_offset|default(0)|int %}
	{% set s0 = [s + temperature_offset_t0, 0]|max %}
	{% set s1 = [s + temperature_offset_t1, 0]|max %}
	{% if temperature_offset_t0 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t0}°C added to toolhead T0."
	{% endif %}
	{% if temperature_offset_t1 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t1}°C added to toolhead T1."
	{% endif %}
	{% else %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	M104.1 S{s0} T0
	M104.1 S{s1} T1
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% else %}
	M104.1 S{s} T{t}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M109]
rename_existing = M109.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M109" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M109" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	M109.1 S{s} T{t}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro SET_HEATER_TEMPERATURE]
rename_existing = SET_HEATER_TEMPERATURE_BASE
gcode = 
	
	{% set heater = params.HEATER|default("") %}
	{% set target = params.TARGET|default(0)|int %}
	
	DEBUG_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="heater: {heater}, target: {target}"
	
	{% set t = -1 %}
	{% if heater|lower == "extruder" or heater|lower == "extruder1" %}
	
	{% set t = 0 if heater|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and target > 0 %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set target = [target + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE_BASE HEATER="{heater}" TARGET={target}
	
	{% if t != -1 and printer.fastconfig.settings.beacon is defined %}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro TEMPERATURE_WAIT]
rename_existing = TEMPERATURE_WAIT_BASE
gcode = 
	
	{% set sensor = params.SENSOR|default("") %}
	{% set minimum = params.MINIMUM|default(-1)|int %}
	{% set maximum = params.MAXIMUM|default(-1)|int %}
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="sensor: {sensor}, minimum: {minimum}, maximum: {maximum}"
	
	{% set t = -1 %}
	{% if sensor|lower == "extruder" or sensor|lower == "extruder1" %}
	
	{% set t = 0 if sensor|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and (minimum > 0 or maximum > 0) %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% if minimum > -1 %}
	{% set minimum = [minimum + temperature_offset, 0]|max %}
	{% endif %}
	{% if maximum > -1 %}
	{% set maximum = [maximum + temperature_offset, 0]|max %}
	{% endif %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set id = "sensor " ~ sensor if t == -1 else "toolhead T" ~ t %}
	
	
	{% if minimum > -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum} MAXIMUM={maximum}
	{% elif minimum > -1 and maximum == -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum}
	{% elif minimum == -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MAXIMUM={maximum}
	{% else %}
	
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="neither MINIMUM or MAXIMUM args were specified, call TEMPERATURE_WAIT_BASE is expected to fail"
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}"
	{% endif %}
	
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature for {id} reached."

[gcode_macro SDCARD_PRINT_FILE]
rename_existing = SDCARD_PRINT_FILE_BASE
gcode = 
	{% if printer["ratos"] is defined %}
	PROCESS_GCODE_FILE { rawparams }
	{% else %}
	SDCARD_PRINT_FILE_BASE { rawparams }
	{% endif %}

[gcode_macro SKEW_PROFILE]
rename_existing = SKEW_PROFILE_BASE
variable_loaded_profile = ""
gcode = 
	{% if params.LOAD is defined %}
	{% if printer.fastconfig.settings["skew_correction %s" % params.LOAD] is defined %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='"{params.LOAD}"'
	{% endif %}
	{% endif %}
	
	SKEW_PROFILE_BASE { rawparams }

[gcode_macro SET_SKEW]
rename_existing = SET_SKEW_BASE
gcode = 
	{% if params.CLEAR is defined %}
	{% if params.CLEAR|default(0)|int == 1 %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='""'
	{% endif %}
	{% endif %}
	
	SET_SKEW_BASE { rawparams }

[gcode_macro SET_VELOCITY_LIMIT]
rename_existing = SET_VELOCITY_LIMIT_BASE
gcode = 
	{% if params.ACCEL_TO_DECEL is defined %}
	
	{% if params.ACCEL is defined %}
	{% set accel = params.ACCEL|float %}
	{% else %}
	{% set accel = printer.toolhead.max_accel|float %}
	{% endif %}
	
	{% if params.VELOCITY is defined %}
	{% set velocity = params.VELOCITY|float %}
	{% else %}
	{% set velocity = printer.toolhead.max_velocity|float %}
	{% endif %}
	
	{% if params.SQUARE_CORNER_VELOCITY is defined %}
	{% set scv = params.SQUARE_CORNER_VELOCITY|float %}
	{% else %}
	{% set scv = printer.toolhead.square_corner_velocity|float %}
	{% endif %}
	
	{% set mcr = params.ACCEL_TO_DECEL|float / accel %}
	
	DEBUG_ECHO PREFIX="SET_VELOCITY_LIMIT" MSG="ACCEL={accel}, VELOCITY={velocity}, SQUARE_CORNER_VELOCITY={scv}, MINIMUM_CRUISE_RATIO={mcr}"
	
	SET_VELOCITY_LIMIT_BASE ACCEL={accel} VELOCITY={velocity} SQUARE_CORNER_VELOCITY={scv} MINIMUM_CRUISE_RATIO={1-mcr}
	
	{% else %}
	
	SET_VELOCITY_LIMIT_BASE { rawparams }
	
	{% endif %}

[gcode_macro BED_MESH_CALIBRATE]
rename_existing = _BED_MESH_CALIBRATE_BASE
variable_abl_and_home_z_if_required = True
gcode = 
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	{% if abl_and_home_z_if_required %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% endif %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set beacon_default_probe_method = printer.fastconfig.settings.beacon.default_probe_method|default('proximity') %}
	{% set probe_method = params.PROBE_METHOD|default(beacon_default_probe_method)|lower %}
	{% if probe_method == 'proximity' %}
	_CHECK_ACTIVE_BEACON_MODEL_TEMP TITLE="Bed mesh calibration warning"
	{% endif %}
	{% endif %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_BED_MESH_CALIBRATE_BASE {rawparams}
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	_APPLY_RATOS_BED_MESH_PARAMETERS {rawparams}
	{% endif %}

[gcode_macro SET_GCODE_OFFSET]
rename_existing = SET_GCODE_OFFSET_BASE
gcode = 
	DEBUG_ECHO PREFIX="SET_GCODE_OFFSET" MSG="{rawparams|replace('"', '')|replace("'", '')}"
	{% set z_before = printer.gcode_move.homing_origin.z|float %}
	SET_GCODE_OFFSET_BASE {rawparams}
	_AFTER_SET_GCODE_OFFSET Z_BEFORE={z_before}

[gcode_macro _AFTER_SET_GCODE_OFFSET]
gcode = 
	{% set z_before = params.Z_BEFORE|float %}
	{% set z_after = printer.gcode_move.homing_origin.z|float %}
	{% if z_before != z_after %}
	_ALERT_NON_ZERO_Z_OFFSET FORCE=1
	{% endif %}

[gcode_macro _START_PRINT_PARK]
gcode = 
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_x = printer["gcode_macro RatOS"].start_print_park_x %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% if printer["gcode_macro RatOS"].start_print_park_x is defined and printer["gcode_macro RatOS"].start_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="start_print_park_x is ignored for IDEX printers"
	{% endif %}
	PARK_TOOLHEAD
	G90
	{% endif %}
	
	
	_PARK LOCATION={start_print_park_in} X={start_print_park_x}
	G0 Z{z} F{z_speed}

[gcode_macro _END_PRINT_PARK]
gcode = 
	{% if printer["dual_carriage"] is defined %}
	
	{% if printer["gcode_macro RatOS"].end_print_park_x is defined and printer["gcode_macro RatOS"].end_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="end_print_park_x is ignored for IDEX printers"
	{% endif %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	PARK_TOOLHEAD
	G90
	{% endif %}
	_PARK LOCATION={printer["gcode_macro RatOS"].end_print_park_in} X={printer["gcode_macro RatOS"].end_print_park_x}

[gcode_macro _PARK]
gcode = 
	
	{% set x = params.X %}
	{% set location = params.LOCATION|default('back')|lower %}
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	{% set nozzle_priming = printer["gcode_macro RatOS"].nozzle_priming|lower %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="park"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% if x != '' %}
	{% if x|float >= printer.toolhead.axis_minimum.x + 5 and x|float <= printable_x_max - 5 %}
	{% set park_x = x|float %}
	{% else %}
	{action_respond_info('The requested X co-ordinate is outside the defined axis bounds - using defaults')}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	{% else %}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	
	
	{% set park_y = printable_y_max - 15 %}
	{% if location == 'front' %}
	{% set park_y = printer.toolhead.axis_minimum.y + 5 %}
	{% elif location == 'center' %}
	{% set park_y = printable_y_max / 2 %}
	{% elif location == 'primeblob' and printer["dual_carriage"] is defined %}
	
	{% set park_y = printable_y_max - 15 %}
	{% endif %}
	
	
	{% if location == 'primeblob' and printer["dual_carriage"] is not defined %}
	{% if (nozzle_priming == 'primeblob' or nozzle_priming == 'primeline') %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set park_x = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set park_x = printable_x_max - 5 %}
	{% else %}
	{% set park_x = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set park_y = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set park_y = printable_y_max - 5 %}
	{% else %}
	{% set park_y = nozzle_prime_start_y|float %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	G0 X{park_x} Y{park_y} F{speed}
	{% else %}
	
	G0 Y{park_y} F{speed}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="park"

[gcode_macro SAVE_PROBE_RESULT]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	{% set last_z_offset = 9999.9 %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if beacon_contact_prime_probing %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	{% else %}
	{% set last_z_offset = printer.beacon.last_sample.dist - current_z %}
	{% endif %}
	{% elif printer.fastconfig.settings.bltouch is defined  %}
	{% set config_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% elif printer.fastconfig.settings.probe is defined  %}
	{% set config_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% endif %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Saving offset adjustment of {last_z_offset} in {params.VARIABLE|default('last_z_offset')}"
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={params.VARIABLE|default('last_z_offset')} VALUE={last_z_offset}

[gcode_macro PROBE_FOR_PRIMING]
gcode = 
	
	{% set probe_for_priming_disable_mesh_constraints = true if printer["gcode_macro RatOS"].probe_for_priming_disable_mesh_constraints|default(false)|lower == 'true' else false %}
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower != 'false' %}
	SAVE_GCODE_STATE NAME=probe_for_priming_state
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the prime location.."
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set t = params.TOOLHEAD|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% if idex_mode == '' %}
	
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% if t == 0 %}
	{% set x_start = 5 %}
	{% else %}
	{% set x_start = printable_x_max - 5 %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% endif %}
	{% endif %}
	{% set z = printer.fastconfig.settings.bed_mesh.horizontal_move_z|float %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% if printer.fastconfig.settings.bltouch is defined %}
	{% set x_offset = printer.fastconfig.settings.bltouch.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.bltouch.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% elif printer.fastconfig.settings.probe is defined %}
	{% set x_offset = printer.fastconfig.settings.probe.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.probe.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% elif printer.fastconfig.settings.beacon is defined %}
	{% set x_offset = printer.fastconfig.settings.beacon.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.beacon.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.beacon.trigger_distance|float %}
	{% else %}
	{ action_raise_error("No probe, beacon or bltouch section found. Adaptive priming only works with a [probe], [beacon] or [bltouch] section defined.") }
	{% endif %}
	
	{% if z < z_offset %}
	{ action_raise_error("Horizontal move Z ({z}) is below your probe's Z offset ({z_offset}). Please adjust your horizontal_move_z setting in [bed_mesh] to be above {z}.") }
	{% endif %}
	
	{% if not probe_for_priming_disable_mesh_constraints %}
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float - x_offset %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float - y_offset %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float - x_offset %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float - y_offset %}
	
	
	{% set x_start = [[x_start, max_x]|min, min_x]|max %}
	{% set y_start = [[y_start, max_y]|min, min_y]|max %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the start of the prime location at {x_start}, {y_start}"
	
	G90
	
	M83
	
	G0 Z{z} F{z_speed}
	
	G1 X{x_start} Y{y_start} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result
	{% endif %}
	
	{% if idex_mode == '' %}
	
	{% set x_end = x_start %}
	{% set y_end = y_start + 45 %}
	{% else %}
	
	{% if t==1 %}
	{% set x_end = x_start - 45 %}
	{% else %}
	{% set x_end = x_start + 45 %}
	{% endif %}
	{% set y_end = y_start %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the end of the prime location at {x_end}, {y_end}"
	G1 X{x_end} Y{y_end} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result
	{% endif %}
	
	RESTORE_GCODE_STATE NAME=probe_for_priming_state
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	{% endif %}

[gcode_macro RESET_PRIME_PROBE_STATE]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result VALUE=None
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result_t1 VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result_t1 VALUE=None
	{% endif %}

[gcode_macro PROBE_CURRENT_POSITION]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	SAVE_GCODE_STATE NAME=probe_current_position_state
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	ASSERT_PROBE_DEPLOYED
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_prime_probing %}
	PROBE PROBE_METHOD=contact SAMPLES=1
	{% else %}
	PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	BEACON_QUERY
	{% else %}
	
	RESTORE_GCODE_STATE NAME=probe_current_position_state MOVE=1 MOVE_SPEED={printer["gcode_macro RatOS"].macro_z_speed|float}
	{% endif %}

[gcode_macro PRIME_BLOB]
description = Prints a primeblob, used internally, if configured, as part of the START_PRINT macro.
variable_x_offset = 5
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="prime_blob"
	SET_MACRO_TRAVEL_SETTINGS
	
	RATOS_ECHO PREFIX="Priming" MSG="Priming nozzle with prime blob.."
	
	
	{% set current_toolhead = 0 %}
	
	
	{% set target_idex_mode = '' %}
	{% set extruder = 'extruder' %}
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE is defined %}
	{% set target_idex_mode = params.IDEX_MODE|default('')|lower %}
	{% else %}
	{ action_raise_error("IDEX_MODE parameter not found for PRIME_BLOB macro. This is likely a bug.") }
	{% endif %}
	RATOS_ECHO PREFIX="Priming" MSG="Priming in IDEX {target_idex_mode} mode.."
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set current_toolhead = 1 if current_idex_mode=='primary' else 0 %}
	{% set extruder = 'extruder1' if current_toolhead == 1 else 'extruder' %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	SAVE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set fan_speed = printer["gcode_macro RatOS"].nozzle_prime_bridge_fan|float %}
	{% set nozzle_diameter = printer.fastconfig.settings[extruder].nozzle_diameter|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set has_start_offset_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) != 9999.9 %}
	{% if printer["dual_carriage"] is defined %}
	{% set has_start_offset_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) != 9999.9 %}
	{% endif %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_z_height = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set nozzle_prime_direction = printer["gcode_macro RatOS"].nozzle_prime_direction|lower %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% if target_idex_mode == '' %}
	
	{% set x_factor = 0 %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% set y_factor = -1 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% if nozzle_prime_start_y|float < printable_y_max / 2 %}
	{% set y_factor = 1 %}
	{% else %}
	{% set y_factor = -1 %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_direction == 'forwards' %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_direction == 'backwards' %}
	{% set y_factor = -1 %}
	{% endif %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% else %}
	{% set z = start_print_park_z_height %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% set y_factor = 0 %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set x_start = center_x / 2 + 5 %}
	{% set x_factor = 1 %}
	{% else %}
	
	
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% if current_toolhead == 0 %}
	{% set x_start = 55 %}
	{% set x_factor = -1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 55 %}
	{% set x_factor = 1 %}
	{% endif %}
	{% else %}
	{% if current_toolhead == 0 %}
	{% set x_start = 5 %}
	{% set x_factor = 1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 5 %}
	{% set x_factor = -1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_x_max - 5 %}
	{% endif %}
	{% set z = 10 %}
	{% endif %}
	
	{% set start_z_offset = 0 %}
	{% set end_z_offset = 0 %}
	{% if has_start_offset_t0 %}
	{% set start_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) %}
	{% set end_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_end_result|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t0) ) }
	{% endif %}
	{% if end_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t0) )  }
	{% endif %}
	{% set start_z_offset = start_z_probe_result_t0 %}
	{% set end_z_offset = end_z_probe_result_t0 %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	{% if current_toolhead == 1 or both_toolheads or target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	{% if has_start_offset_t1 %}
	{% set start_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) %}
	{% set end_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_end_result_t1|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t1) ) }
	{% endif %}
	{% if end_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t1) ) }
	{% endif %}
	{% set start_z_offset = [start_z_offset, start_z_probe_result_t1]|max %}
	{% set end_z_offset = [end_z_offset, start_z_probe_result_t1]|max %}
	{% endif %}
	{% endif %}
	{% if target_idex_mode != 'copy' and target_idex_mode != 'mirror' %}
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% set original_start_z_offset = start_z_offset %}
	{% set original_end_z_offset = end_z_offset %}
	{% set start_z_offset = original_end_z_offset %}
	{% set end_z_offset = original_start_z_offset %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	DEBUG_ECHO PREFIX="PRIME_BLOB" MSG="x_start: {x_start}, y_start: {y_start}, x_factor: {x_factor}, y_factor: {y_factor}, z: {z}, start_z_offset: {start_z_offset}, end_z_offset: {end_z_offset}"
	
	
	G90
	
	M83
	RATOS_ECHO PREFIX="Priming" MSG="Lifting Z to {z}.."
	
	G0 Z{z} F{z_speed}
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% if start_print_park_in != 'primeblob' %}
	G1 X{x_start} F{speed}
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% endif %}
	{% else %}
	
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% if target_idex_mode=="copy" or target_idex_mode=="mirror" %}
	RATOS_ECHO PREFIX="Priming" MSG="Mirroring move to {x_start}, {y_start} along the edge of the print area.."
	
	_IDEX_MIRROR PRIMING=1
	{% else %}
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% endif %}
	G1 X{x_start} F{speed}
	{% endif %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Starting prime blob.."
	
	G1 Z{0.5 + start_z_offset} F{z_speed}
	
	G1 Y{y_start} F{speed}
	
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	
	M106 S{fan_speed}
	
	G1 Z5 F100 E5
	G92 E0
	RATOS_ECHO PREFIX="Priming" MSG="Bridging with {((fan_speed/255) * 100)|int}% fan speed.."
	
	G1 F3000 X{x_start + (15 * x_factor)} Y{y_start + (15 * y_factor)} E{1 / ((0.4 / nozzle_diameter) ** 2)}
	
	
	
	G1 F3000 X{x_start + (20 * x_factor)} Y{y_start + (20 * y_factor)} Z{3.8 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (34 * x_factor)} Y{y_start + (34 * y_factor)} Z{2.6 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (38 * x_factor)} Y{y_start + (38 * y_factor)} Z{1.4 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (42 * x_factor)} Y{y_start + (42 * y_factor)} Z{0.2 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	
	M106 S0
	
	G1 F3000 X{x_start + (46 * x_factor)} Y{y_start + (46 * y_factor)} Z{0.2 + end_z_offset} E0.6
	
	G1 F{speed} X{x_start + (50 * x_factor)} Y{y_start + (50 * y_factor)}
	
	
	{% if target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if target_idex_mode == "copy" %}
	{% if first_y >= 0 %}
	_IDEX_COPY DANCE=0 Y={first_y}
	{% else %}
	_IDEX_COPY DANCE=0 Y={params.Y1}
	{% endif %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	RESTORE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="prime_blob"
	
	
	G92 E0

[gcode_macro UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set temp = params.TEMP|default(220)|int %}
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_UNLOAD_FILAMENT TEMP={temp} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_UNLOAD_FILAMENT]
description = Unload filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_UNLOAD_FILAMENT" MSG="TEMP: {temp}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=unload_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	G4 P3000
	
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD=0 NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=unload_state
	
	
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament unloading completed"

[gcode_macro _IDEX_UNLOAD_FILAMENT]
description = Unload filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading T{toolhead} filament..."
	
	DEBUG_ECHO PREFIX="_IDEX_UNLOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} AUTOMATED={automated}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="T{toolhead} filament unloading completed"

[gcode_macro _UNLOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LEGACY_UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
gcode = 
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set unload_speed = 5 * 60 %}
	{% set unload_length = printer["gcode_macro RatOS"].filament_unload_length|float %}
	M117 Unloading filament...
	
	G0 E10 F300
	
	G0 E-5 F3600
	
	G4 P3000
	
	G0 E5 F6000
	
	G0 E-15 F6000
	
	G0 E-{unload_length} F{unload_speed}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}
	M117 Filament unloaded!
	RESPOND MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	RATOS_ECHO MSG="Unloading filament from nozzle to cooling zone... Please wait!"
	
	_PURGE_BEFORE_UNLOAD TOOLHEAD={toolhead}
	
	{% if printer["gcode_macro _UNLOAD_WITHOUT_TIP_FORMING"] is defined %}
	
	_UNLOAD_WITHOUT_TIP_FORMING TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	_UNLOAD_WITH_TIP_FORMING NAME='{filament_name}' TYPE='{filament_type}'
	{% endif %}
	
	G4 P3000

[gcode_macro _UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	{% set tooolhead_sensor_to_extruder_gear_distance = printer["gcode_macro T%s" % toolhead].tooolhead_sensor_to_extruder_gear_distance|float %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER" MSG="TOOLHEAD: {toolhead}"
	
	
	G0 E-{extruder_gear_to_cooling_position_distance + tooolhead_sensor_to_extruder_gear_distance + 50} F{extruder_load_speed}
	
	RATOS_ECHO MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_WITH_TIP_FORMING]
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	{% if filament_name != '' and filament_type != '' %}
	_UNLOAD_KNOWN_FILAMENT NAME={filament_name} TYPE={filament_type}
	{% else %}
	_UNLOAD_UNKNOWN_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _UNLOAD_KNOWN_FILAMENT]
description = User overrideable tip forming macro if slicer filament profiles are known
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	RATOS_ECHO PREFIX="FILAMENT TYPE" MSG='{filament_type}'
	RATOS_ECHO PREFIX="FILAMENT PROFILE" MSG='{filament_name}'
	
	
	{% if filament_name == "Prusament PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% elif filament_name == "Nobufil PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% else %}
	
	RATOS_ECHO PREFIX="_UNLOAD_KNOWN_FILAMENT" MSG="Filament profile not found!"
	_UNLOAD_UNKNOWN_FILAMENT
	{% endif %}

[gcode_macro _UNLOAD_UNKNOWN_FILAMENT]
description = User overrideable standard tip forming macro
gcode = 
	
	DEBUG_ECHO PREFIX="_UNLOAD_UNKNOWN_FILAMENT" MSG="Using standard tip forming macro!"
	
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10

[gcode_macro _TIP_FORMING]
gcode = 
	
	{% set cooling_moves = params.COOLING_MOVES|default(4)|int %}
	{% set cooling_move_length = params.COOLING_MOVE_LENGTH|default(10)|float %}
	{% set start_cooling_speed = params.START_COOLING_SPEED|default(10)|float * 60 %}
	{% set end_cooling_speed = params.END_COOLING_SPEED|default(50)|float * 60 %}
	{% if cooling_moves == 0 %}
	{% set cooling_move_length = 0 %}
	{% endif %}
	
	
	{% set dip = true if params.DIP|default(false)|lower == "true" else false %}
	{% set dip_length = params.DIP_LENGTH|default(22)|float %}
	{% set dip_speed = params.DIP_SPEED|default(30)|float * 60 %}
	{% set dip_retract_speed = params.DIP_RETRACT_SPEED|default(70)|float * 60 %}
	
	
	{% set retract_length = params.RETRACT_LENGTH|default(18)|float %}
	{% set start_retract_speed = params.START_RETRACT_SPEED|default(120)|float * 60 %}
	{% set end_retract_speed = params.END_RETRACT_SPEED|default(20)|float * 60 %}
	
	DEBUG_ECHO PREFIX="_TIP_FORMING" MSG="cooling_moves: {cooling_moves}, cooling_move_length: {cooling_move_length}, start_cooling_speed: {start_cooling_speed}, end_cooling_speed: {end_cooling_speed}, dip: {dip}, dip_length: {dip_length}, dip_speed: {dip_speed}, dip_retract_speed: {dip_retract_speed}, retract_length: {retract_length}, start_retract_speed: {start_retract_speed}, end_retract_speed: {end_retract_speed}"
	
	M220 S100
	
	
	G92 E0
	{% set retract = retract_length + cooling_move_length / 2 - 15 %}
	G1 E-15 F{start_retract_speed}
	G1 E-{0.7 * retract} F{1.0 * end_retract_speed}
	G1 E-{0.2 * retract} F{0.5 * end_retract_speed}
	G1 E-{0.1 * retract} F{0.3 * end_retract_speed}
	
	
	G92 E0
	{% if cooling_moves > 0 %}
	{% set i = (end_cooling_speed - start_cooling_speed) / (2 * cooling_moves - 1) %}
	{% for m in range(cooling_moves) %}
	G1 E{cooling_move_length} F{(start_cooling_speed + i * m * 2)}
	G1 E-{cooling_move_length} F{(start_cooling_speed + i * (m * 2 + 1))}
	{% endfor %}
	{% endif %}
	
	
	G92 E0
	{% if dip %}
	G1 E{dip_length} F{dip_speed}
	G4 P100
	G1 E-{dip_length} F{dip_retract_speed}
	{% endif %}
	
	G92 E0
	M400

[delayed_gcode __ON_FILAMENT_SENSOR_BUTTON_PRESSED_STARTUP_GUARD]
initial_duration = 2.
gcode = 
	SET_GCODE_VARIABLE MACRO=_ON_FILAMENT_SENSOR_BUTTON_PRESSED VARIABLE=startup_complete VALUE=True

[gcode_macro _ON_FILAMENT_SENSOR_BUTTON_PRESSED]
variable_startup_complete = False
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set toolhead_sensor_button_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_sensor_button_only_when_sensor_enabled|default(false)|lower == 'true' %}
	
	
	{% if not startup_complete and sensor_enabled %}
	{action_emergency_stop("RatOS: The T%s filament sensor button was triggered immediately on printer startup. This is likely a false trigger. Please check your filament sensor wiring and configuration!" % (toolhead,))}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_SENSOR_BUTTON_PRESSED" MSG="TOOLHEAD: {toolhead}, SENSOR_ENABLED: {sensor_enabled}, TOOLHEAD_SENSOR_BUTTON_ONLY_WHEN_SENSOR_ENABLED: {toolhead_sensor_button_only_when_sensor_enabled}"
	
	{% if not printer.virtual_sdcard.is_active and (sensor_enabled or not toolhead_sensor_button_only_when_sensor_enabled) %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	{% set toolhead_detect_clog_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_detect_clog_only_when_sensor_enabled|default(true)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}, ENABLE_CLOG_DETECTION: {enable_clog_detection}, TOOLHEAD_DETECT_CLOG_ONLY_WHEN_SENSOR_ENABLED: {toolhead_detect_clog_only_when_sensor_enabled}, SENSOR_ENABLED: {sensor_enabled}"
	
	{% if enable_clog_detection and (sensor_enabled or not toolhead_detect_clog_only_when_sensor_enabled) %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_clog_detection %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_FILAMENT_END]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set clogged = true if params.CLOGGED|default(false)|lower == 'true' else false %}
	
	
	{% set unload_after_runout = printer["gcode_macro T%s" % toolhead].unload_after_runout|float %}
	
	
	{% if clogged %}
	_LED_FILAMENT_CLOG TOOLHEAD={toolhead}
	{% else %}
	_LED_FILAMENT_RUNOUT TOOLHEAD={toolhead}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_END" MSG="TOOLHEAD: {toolhead}"
	
	{% if printer.virtual_sdcard.is_active %}
	{% if not printer.pause_resume.is_paused %}
	PAUSE RUNOUT=True
	{% endif %}
	{% if not clogged and unload_after_runout %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	{% if not clogged and printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true'%}
	_JOIN_SPOOL TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M600]
description = Executes a color change by pausing the printer an unloading the filament.
gcode = 
	PAUSE
	UNLOAD_FILAMENT AUTOMATED=True
	RATOS_ECHO MSG="Please load new filament and resume"

[gcode_macro COLD_PULL]
description = Automated hotend cold pull.
gcode = 
	
	{% set extrusion_temp = params.EXTRUSION_TEMP|default(220)|int %}
	{% set cold_pull_temp = params.COLD_PULL_TEMP|default(80)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	
	{% if printer["dual_carriage"] is not defined %}
	{% set toolhead = 0 %}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead != 0 and toolhead != 1 %}
	{action_raise_error("Please select toolhead! 0 = left, 1 = right toolhead")}
	{% endif %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	RATOS_ECHO MSG="Starting cold pull on T{toolhead}..."
	{% else %}
	RATOS_ECHO MSG="Starting cold pull..."
	{% endif %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	SAVE_GCODE_STATE NAME=cold_pull_state
	
	
	{% if printer["dual_carriage"] is defined and "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	RATOS_ECHO MSG="Heating T{toolhead} to {extrusion_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={extrusion_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={extrusion_temp} MAXIMUM={extrusion_temp + 2}
	
	
	G4 P3000
	
	
	RATOS_ECHO MSG="extruding..."
	G92 E0
	G1 E30 F300
	G92 E0
	
	
	RATOS_ECHO MSG="Cooling T{toolhead} to {cold_pull_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={cold_pull_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={cold_pull_temp} MAXIMUM={cold_pull_temp + 2}
	
	
	G4 P10000
	
	
	RATOS_ECHO MSG="cold pull..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-40 VELOCITY=5 ACCEL=100
	
	
	RATOS_ECHO MSG="eject filament..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-200 VELOCITY=20 ACCEL=500
	
	
	RATOS_ECHO MSG="cooling down extruder..."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	RESTORE_GCODE_STATE NAME=cold_pull_state
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	
	CONSOLE_ECHO TITLE="Cold pull complete" MSG="Please remove the filament from the PTFE tube and cut the end off. Do NOT try to load it again." TYPE="warning"

[gcode_macro _USER_START_PRINT_BEFORE_HOMING]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_BED]
gcode = 

[gcode_macro _USER_START_PRINT_BED_MESH]
gcode = 

[gcode_macro _USER_START_PRINT_PARK]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 

[gcode_macro _USER_START_PRINT_HEAT_CHAMBER]
description = Uses the extruder sensor to wait for chamber temp. Override the _START_PRINT_HEAT_CHAMBER macro to implement heated chamber handling.
gcode = 
	
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}

[gcode_macro _USER_END_PRINT_BEFORE_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_AFTER_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_PARK]
gcode = 

[gcode_macro _USER_END_PRINT_FINISHED]
description = User hook for when the print is finished after gcode state has been restored.
gcode = 

[gcode_macro _USER_START_PRINT]
gcode = 

[gcode_macro _USER_END_START_PRINT]
gcode = 

[gcode_macro _USER_START_FEATURE]
gcode = 

[gcode_macro _USER_END_FEATURE]
gcode = 

[gcode_macro _USER_BEFORE_IDLE_TIMEOUT]
gcode = 

[gcode_macro _USER_AFTER_IDLE_TIMEOUT]
gcode = 

[gcode_macro ECHO_T_VARS]
description = Echo Toolhead variables to the console.
gcode = 
	{% set t = params.T|default(0) %}
	RATOS_ECHO MSG="T{t} Variables"
	{% for var, value in printer["gcode_macro T%s" % t].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ECHO_RATOS_VARS]
description = Echo RatOS variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro RatOS"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ENSURE_CRITICAL_RATOS_INIT]
variable_completed = False
gcode = 
	{% if not completed %}
	CALCULATE_PRINTABLE_AREA
	SET_GCODE_VARIABLE MACRO=ENSURE_CRITICAL_RATOS_INIT VARIABLE=completed VALUE=True
	{% endif %}

[delayed_gcode RATOS_INIT]
initial_duration = 0.1
gcode = 
	{action_respond_info("Initializing RatOS...")}
	ENSURE_CRITICAL_RATOS_INIT
	_LED_STANDBY
	INITIAL_FRONTEND_UPDATE
	_CHAMBER_FILTER_SANITY_CHECK
	{% if printer.fastconfig.settings.beacon is defined %}
	
	_BED_MESH_SANITY_CHECK
	{% endif %}
	{% set svv = printer.save_variables.variables %}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=0 C={svv.nozzle_expansion_coefficient_t0|default(0.06)|float}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=1 C={svv.nozzle_expansion_coefficient_t1|default(0.06)|float}
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=idex_applied_offset

[delayed_gcode RATOS_LOGO]
initial_duration = 2
gcode = 
	
	
	
	
	
	ENSURE_CRITICAL_RATOS_INIT
	HELLO_RATOS
	_ALERT_NON_ZERO_Z_OFFSET

[gcode_macro _ALERT_NON_ZERO_Z_OFFSET]
gcode = 
	{% set force = params.FORCE|default(0)|int == 1 %}
	{% set user_offset = printer.named_offsets.user_probe_z_offset.z|float %}
	{% set gcode_offset = printer.gcode_move.homing_origin.z|float %}
	{% set combined_offset = user_offset + gcode_offset %}
	
	{% if force or user_offset != 0 or gcode_offset != 0 %}
	{% set title = "User-adjusted Z-offset of %.3f mm is active" % combined_offset %}
	{% set msg = "" %}
	{% set nl = "" %}
	{% if user_offset != 0 %}
	{% set msg = msg + "beacon true zero user Z-offset: %.3f mm (to clear, use Z_OFFSET_APPLY_PROBE CLEAR=1)" % user_offset %}
	{% set nl = "_N_" %}
	{% endif %}
	{% if gcode_offset != 0 %}
	{% set msg = msg + nl + "G-code Z-offset: %.3f mm" % gcode_offset %}
	{% endif %}
	CONSOLE_ECHO TITLE="{title}" TYPE="info" MSG="{msg}"
	{% endif %}

[gcode_macro _INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE]
gcode = 
	{% set variable = params.VARIABLE|string %}
	{% set svv = printer.save_variables.variables %}
	{% set nlu_msg = "no longer used, please remove" %}
	{% if svv[variable] is defined %}
	{% set v = svv[variable]|string|replace('"', '')|replace("'", "") %}
	{% if not nlu_msg in v %}
	SAVE_VARIABLE VARIABLE={variable} VALUE='"{nlu_msg} (was {v})"'
	{% endif %}
	CONSOLE_ECHO TITLE="Deprecated ratos-variables.cfg variable" TYPE="warning" MSG="The variable {variable} is no longer used, please remove it from your ratos-variables.cfg file."
	{% endif %}

[gcode_macro _NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK]
gcode = 
	
	
	
	
	
	
	
	{% set t = params.T|int %}
	{% set c = params.C|float %}
	{% set normal_low = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_low|default(0.05)|float %}
	{% set normal_high = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_high|default(0.10)|float %}
	
	{% if c < 0 %}
	
	{action_emergency_stop("Invalid nozzle_expansion_coefficient_t%s value in ratos-variables.cfg: %.3f. It must be non-negative." % (t, c))}
	{% endif %}
	{% if c >= normal_high %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite high. Please verify that this is correct."
	{% endif %}
	{% if c <= normal_low %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite low. Please verify that this is correct."
	{% endif %}

[gcode_macro INITIAL_FRONTEND_UPDATE]
gcode = 
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_error = printer["gcode_macro RatOS"].status_color_error|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_unknown}"'
	{% endif %}
	
	
	{% set t0_sensor = "undefined" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	{% set t0_sensor = "detected" %}
	{% else %}
	{% set t0_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t0_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	{% set t1_sensor = "undefined" %}
	{% if printer["dual_carriage"] is defined and printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	{% set t1_sensor = "detected" %}
	{% else %}
	{% set t1_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t1_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	{% if svv.t0_filament is defined and printer["gcode_macro T0"] is defined %}
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	{% if t0_sensor != "empty" %}
	{% set t0_filament_type = svv.t0_filament[0]|default('')|string %}
	{% set t0_filament_name = svv.t0_filament[1]|default('')|string %}
	{% set t0_filament_temp = svv.t0_filament[2]|default(0)|float %}
	{% if t0_filament_name != '' and t0_filament_type != '' and t0_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{t0_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{t0_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={t0_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}
	{% if svv.t1_filament is defined and printer["gcode_macro T1"] is defined %}
	{% if printer["gcode_macro T1"].filament_name is defined and printer["gcode_macro T1"].filament_type is defined and printer["gcode_macro T1"].filament_temp is defined %}
	{% if t1_sensor != "empty" %}
	{% set t1_filament_type = svv.t1_filament[0]|default('')|string %}
	{% set t1_filament_name = svv.t1_filament[1]|default('')|string %}
	{% set t1_filament_temp = svv.t1_filament[2]|default(0)|float %}
	{% if t1_filament_name != '' and t1_filament_type != '' and t1_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='"{t1_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='"{t1_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE={t1_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t1_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro CALCULATE_PRINTABLE_AREA]
variable_calculated = False
gcode = 
	{% if not calculated %}
	{% set bed_margin_x = printer["gcode_macro RatOS"].bed_margin_x %}
	{% set bed_margin_y = printer["gcode_macro RatOS"].bed_margin_y %}
	
	
	
	{% set tool = 0 if printer["gcode_macro T0"] is not defined or printer["gcode_macro T0"].active else 1 %}
	{% set max_x = printer.toolhead.axis_maximum.x if printer["dual_carriage"] is defined and tool == 0 else printer.toolhead.axis_maximum.x - bed_margin_x[1] %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	
	
	{% set max_x = printer.toolhead.axis_maximum.x %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="printer.toolhead.axis_maximum.x {printer.toolhead.axis_maximum.x}"
	
	{% set max_y = printer.toolhead.axis_maximum.y - bed_margin_y[1]%}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_x_max VALUE={max_x}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_y_max VALUE={max_y}
	SET_GCODE_VARIABLE MACRO=CALCULATE_PRINTABLE_AREA VARIABLE=calculated VALUE=True
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	RATOS_LOG PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	{% endif %}

[gcode_macro CACHE_TOOLHEAD_SETTINGS]
variable_cache = {"global": {"accel": 1000, "ratio": 0.5, "speed": 50, "scv": 5}}
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set dummy = cache.__setitem__(key, {"accel": printer.toolhead.max_accel, "ratio": printer.toolhead.minimum_cruise_ratio, "speed": printer.toolhead.max_velocity, "scv": printer.toolhead.square_corner_velocity}) %}
	SET_GCODE_VARIABLE MACRO=CACHE_TOOLHEAD_SETTINGS VARIABLE=cache VALUE="{cache | pprint | replace("\n", "") | replace("\"", "\\\"")}"
	DEBUG_ECHO PREFIX="CACHE_TOOLHEAD_SETTINGS" MSG="Toolhead settings cached for {key}. {printer.toolhead.max_accel} accel, {printer.toolhead.minimum_cruise_ratio} ratio, {printer.toolhead.max_velocity} velocity, {printer.toolhead.square_corner_velocity} scv."

[gcode_macro RESTORE_TOOLHEAD_SETTINGS]
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set values = printer["gcode_macro CACHE_TOOLHEAD_SETTINGS"].cache.__getitem__(key) %}
	{% if values is not defined or values == 'None' %}
	{ action_raise_error("RESTORE_TOOLHEAD_SETTINGS: Toolhead settings not cached for key '" ~ key ~ "'.") }
	{% endif %}
	SET_VELOCITY_LIMIT ACCEL={values.accel} MINIMUM_CRUISE_RATIO={values.ratio} VELOCITY={values.speed} SQUARE_CORNER_VELOCITY={values.scv}
	DEBUG_ECHO PREFIX="RESTORE_TOOLHEAD_SETTINGS" MSG="Toolhead settings restored. {values.accel} accel, {values.ratio} ratio, {values.speed} velocity, {values.scv} scv."

[gcode_macro SET_MACRO_TRAVEL_SETTINGS]
gcode = 
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float %}
	{% set accel = printer["gcode_macro RatOS"].macro_travel_accel %}
	SET_VELOCITY_LIMIT ACCEL={accel} MINIMUM_CRUISE_RATIO=0.5 VELOCITY={speed} SQUARE_CORNER_VELOCITY={5}
	DEBUG_ECHO PREFIX="SET_MACRO_TRAVEL_SETTINGS" MSG="Macro travel settings set. {accel} accel, {speed} velocity"

[gcode_macro SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% if printer["dual_carriage"] is not defined %}
	
	SET_KINEMATIC_POSITION X={printable_x_max / 2} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	{% else %}
	
	IDEX_SET_CENTER_KINEMATIC_POSITION
	{% endif %}

[gcode_macro IDEX_SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x - (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x + (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY

[gcode_macro VERIFY_HYBRID_INVERTED]
gcode = 
	
	{% set inverted = False %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy is defined and printer.fastconfig.settings.ratos_hybrid_corexy.inverted is defined %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy.inverted|lower == 'true' %}
	{% set inverted = True %}
	{% endif %}
	{% endif %}
	{% if inverted == False %}
	{ action_emergency_stop("ratos_hybrid_corexy NOT INVERTED! Inverted hybrid core-xy bugfix not detected.") }
	{% endif %}

[gcode_macro RATOS_ECHO]
gcode = 
	{% set prefix = "RatOS" %}
	{% set debug = params.DEBUG|default(0)|int %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " | " ~ params.PREFIX %}
	{% endif %}
	{% set prefix = prefix ~ ":" %}
	{% set msg = "" %}
	{% if params.MSG is defined %}
	{% set msg = params.MSG %}
	{% else %}
	{% set msg = "No msg parameter provided (this is a bug or unintended use)." %}
	{% endif %}
	{% if not debug %}
	
	M117 {prefix} {msg}
	{% endif %}
	RATOS_LOG PREFIX="{prefix}" MSG="{msg}"
	{% if not debug %}
	RESPOND PREFIX="{prefix}" MSG="{msg}"
	{% else %}
	CONSOLE_ECHO TITLE="{prefix}" TYPE="debug" MSG="{msg}"
	{% endif %}

[gcode_macro ENABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=True
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=prefix_filter VALUE="'{params.FILTER|default('')|lower}'"
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging enabled."

[gcode_macro DISABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=False
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging disabled."

[gcode_macro DEBUG_ECHO]
variable_enabled = False
variable_prefix_filter = ''
gcode = 
	{% set prefix = "DEBUG" %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " - " ~ params.PREFIX %}
	{% endif %}
	{% if enabled and (prefix_filter|lower == '' or prefix_filter|lower in params.PREFIX|lower) %}
	RATOS_ECHO PREFIX="{prefix}" MSG="{params.MSG}" DEBUG=1
	{% endif %}

[gcode_macro START_FEATURE]
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="Start {params.FEATURE} feature gcode"
	{% set scv = printer.toolhead.square_corner_velocity|int|default(5) %}
	{% set accel = printer.toolhead.max_accel|int|default(10000) %}
	{% set ratio = printer.toolhead.minimum_cruise_ratio|float|default(0.5) %}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="scv" VALUE={scv}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="accel" VALUE={accel}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="ratio" VALUE={ratio}
	_USER_START_FEATURE FEATURE="{params.FEATURE}"

[gcode_macro END_FEATURE]
variable_scv = 5
variable_accel = 10000
variable_ratio = 0.5
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="End {params.FEATURE} feature gcode"
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={scv} ACCEL={accel} MINIMUM_CRUISE_RATIO={ratio}
	_USER_END_FEATURE FEATURE="{params.FEATURE}" SCV={scv} ACCEL={accel} RATIO={ratio}

[gcode_macro _ON_LAYER_CHANGE]
variable_layer_number = 0
description = INTERNAL USE ONLY. Call it from the slicers after layer change custom gcode
gcode = 
	
	{% set layer = params.LAYER|int %}
	
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE={layer}
	SET_PRINT_STATS_INFO CURRENT_LAYER={layer}

[gcode_macro _LEARN_MORE_CALIBRATION]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/calibration" %}
	{% set link_text = "RatOS Calibration Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_CHAMBER_FILTER]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter Control" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_FILAMENT]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/filaments" %}
	{% set link_text = "RatOS Filament Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _CONSOLE_SAVE_CONFIG]
gcode = 
	M118 Click <a class="command text--blue">SAVE_CONFIG</a> to save the settings to your printer.cfg.

[gcode_macro _LOAD_RATOS_SKEW_PROFILE]
gcode = 
	{% set ratos_skew_profile = printer["gcode_macro RatOS"].skew_profile|default("") %}
	{% if ratos_skew_profile != "" %}
	{% if printer.fastconfig.config["skew_correction %s" % ratos_skew_profile] is defined %}
	SKEW_PROFILE LOAD={ratos_skew_profile}
	GET_CURRENT_SKEW
	{% else %}
	{% set line_1 = '"Could not find skew profile %s!_N_Clearing skew correction."' % ratos_skew_profile %}
	CONSOLE_ECHO TITLE="Missing skew profile!" TYPE="warning" MSG={line_1}
	SET_SKEW CLEAR=1
	{% endif %}
	{% endif %}

[gcode_macro M601]
gcode = 
	PAUSE

[gcode_macro _STOP_AND_RAISE_ERROR]
gcode = 
	M84
	_RAISE_ERROR MSG="{params.MSG}"

[gcode_macro _RESET_GCODE_VARIABLES]
description = Reset specified [gcode_macro ...] variables to their original values from configuration when Klipper started.
	- MACRO: Name of the GCODE macro containing the variables to reset.
	- VARIABLES: Comma-separated list of variable names to reset (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- QUIET: (optional) If true, suppresses console echo messages for each reset variable. Default is false.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set quiet = params.QUIET|default("false")|lower in ("true", "1", "yes") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	{% set settings = printer.fastconfig.settings[obj_name|lower] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro %s]" % macro) }
	{% endif %}
	
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if settings["variable_%s" % var] is not defined %}
	{ action_raise_error("Variable '%s' is not defined in settings for [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	
	{% for var in vars %}
	{% set var_value = obj[var] %}
	{% if var_value is defined %}
	{% set v = settings["variable_%s" % var] %}
	{% if v != var_value|string %}
	{% if var_value is string %}
	{% set v = '"\'' ~ v|replace('"', '\\"')|replace("'", "\\'") ~ '\'"' %}
	{% endif %}
	SET_GCODE_VARIABLE MACRO={macro} VARIABLE={var} VALUE={v}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Reset {macro} variable {var} to original value: {v} (was {obj[var]})"
	{% endif %}
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro _SHOW_GCODE_VARIABLES]
description = Show current values of specified [gcode_macro ...] variables.
	- MACRO: Name of the GCODE macro containing the variables to show.
	- VARIABLES: Comma-separated list of variable names to show (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- PAD: (optional) If defined, provide a single character to use for padding variable names to align values in a tabular format in the console output. Default is no padding.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set pad = params.PAD|default("") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	
	{% set ns = namespace() %}
	{% set ns.max_len = 0 %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% set ns.max_len = (ns.max_len, var|length)|max %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if pad %}
	{% set padding = pad * (ns.max_len - var|length) %}
	CONSOLE_ECHO MSG="{var}{padding} {obj[var]}"
	{% else %}
	CONSOLE_ECHO MSG="{var}: {obj[var]}"
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro PAUSE]
description = Pauses the print
rename_existing = PAUSE_BASE
variable_extrude = 1.5
variable_retract = 1.5
variable_fan_speed = 0
variable_idex_mode = ""
variable_idex_toolhead = 0
variable_idex_toolhead_x = 0.0
variable_idex_toolhead_y = 0.0
variable_idex_toolhead_z = 0.0
gcode = 
	RATOS_ECHO MSG="Pausing print..."
	
	
	{% set runout_detected = true if params.RUNOUT|default(false)|lower == 'true' else false %}
	
	
	_LED_PAUSE
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	SAVE_GCODE_STATE NAME=PAUSE_state
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_mode VALUE='"{idex_mode}"'
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={idex_toolhead}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_x VALUE={printer.gcode_move.gcode_position.x|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_y VALUE={printer.gcode_move.gcode_position.y|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_z VALUE={printer.gcode_move.gcode_position.z|float}
	DEBUG_ECHO PREFIX="PAUSE" MSG="idex_mode: {idex_mode}, idex_toolhead: {idex_toolhead}, idex_toolhead_x: {idex_toolhead_x}, idex_toolhead_y: {idex_toolhead_y}, idex_toolhead_z: {idex_toolhead_z}"
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="pause"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if current_z < (max_z - 20.0) %}
	{% set z_safe = 20.0 %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	PAUSE_BASE
	
	
	{% if printer["dual_carriage"] is not defined %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan"].speed|float}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	{% if idex_toolhead == 0 %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t1"].speed|float}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106 S0
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set R = printer["gcode_macro PAUSE"].retract|float %}
	{% if can_extrude %}
	G91
	G1 E-{R} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	{% set pause_print_park_x = printer["gcode_macro RatOS"].pause_print_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].pause_print_park_in %}
	{% if runout_detected %}
	{% set pause_print_park_x = printer["gcode_macro RatOS"].runout_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].runout_park_in %}
	{% endif %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	DEBUG_ECHO PREFIX="PAUSE" MSG="z_speed: {z_speed}, pause_print_park_x: {pause_print_park_x}, pause_print_park_in: {pause_print_park_in}, default_toolhead: {default_toolhead}"
	{% if "xyz" in printer.toolhead.homed_axes %}
	G91
	G1 Z{z_safe} F{z_speed}
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% else %}
	
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	_IDEX_SINGLE X={parking_position}
	{% else %}
	PARK_TOOLHEAD
	{% endif %}
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="pause"
	
	RATOS_ECHO MSG="Print paused"

[gcode_macro RESUME]
description = Resumes the print if the printer is paused.
rename_existing = RESUME_BASE
gcode = 
	
	
	RATOS_ECHO MSG="Resuming print..."
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	
	{% set target_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set target_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if target_idex_mode != '' %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set fan_speed = printer["gcode_macro PAUSE"].fan_speed|float %}
	{% if printer["dual_carriage"] is not defined %}
	M106 S{(fan_speed * 255)}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% else %}
	{% if params.TOOLHEAD is defined %}
	
	{% if params.TOOLHEAD == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% else %}
	{% if printer["gcode_macro PAUSE"].idex_toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	{% if params.TOOLHEAD is defined %}
	_SELECT_TOOL T={params.TOOLHEAD} X=-1 Y=-1 TOOLSHIFT=false
	{% else %}
	_SELECT_TOOL T={printer["gcode_macro PAUSE"].idex_toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	{% endif %}
	
	{% set x = printer["gcode_macro PAUSE"].idex_toolhead_x|float %}
	{% set y = printer["gcode_macro PAUSE"].idex_toolhead_y|float %}
	{% set z = printer["gcode_macro PAUSE"].idex_toolhead_z|float %}
	G1 X{x} Y{y} Z{z} F{speed}
	{% if params.TOOLHEAD is defined %}
	
	SAVE_GCODE_STATE NAME=PAUSE_STATE
	{% endif %}
	{% endif %}
	
	
	{% if params.TOOLHEAD is not defined %}
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% if can_extrude %}
	G91
	G1 E{E} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1 MOVE_SPEED={speed}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	RESUME_BASE
	
	
	_LED_PRINTING
	
	RATOS_ECHO MSG="Print resumed"

[gcode_macro CANCEL_PRINT]
description = Cancels the print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	RATOS_ECHO MSG="Cancelling print..."
	END_PRINT
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	
	CANCEL_PRINT_BASE
	RATOS_ECHO MSG="Print cancelled"

[gcode_macro START_PRINT]
description = Start print procedure, use this in your Slicer.
variable_post_processor_version = 2
variable_is_printing_gcode = False
variable_both_toolheads = True
variable_object_xoffset = 0
variable_first_x = -1
variable_first_y = -1
variable_total_toolshifts = 0
variable_initial_tool = 0
variable_extruder_first_layer_temp = ""
variable_extruder_other_layer_temp = ""
gcode = 
	
	{% if params.EXTRUDER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_TEMP parameter not found.")}
	{% endif %}
	{% if params.EXTRUDER_OTHER_LAYER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_OTHER_LAYER_TEMP parameter not found.")}
	{% endif %}
	{% if params.BED_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. BED_TEMP parameter not found.")}
	{% endif %}
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' and printer["gcode_macro RatOS"].danger_force_allow_auto_center_subject|default(false)|lower != 'true'%}
	
	
	
	
	
	{ action_raise_error("The experimental auto_center_subject feature is not supported in this version of RatOS. Please disable it in the RatOS macro settings.") }
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes and printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% if printer["gcode_macro _VAOC"].is_started|default(true)|lower == 'true' %}
	_VAOC_END
	{% endif %}
	{% endif %}
	
	
	_LED_START_PRINTING
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_USER_START_PRINT { rawparams }
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_probe_stowable = printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% endif %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	{% set X0 = params.X0|default(-1)|float %}
	{% set X1 = params.X1|default(-1)|float %}
	{% set Y0 = params.Y0|default(-1)|float %}
	{% set Y1 = params.Y1|default(-1)|float %}
	{% if first_x == -1 or first_y == -1 %}
	{% set first_x = params.FIRST_X|default(-1)|float %}
	{% set first_y = params.FIRST_Y|default(-1)|float %}
	{% endif %}
	{% set total_toolshifts = params.TOTAL_TOOLSHIFTS|default(0)|int %}
	{% set initial_tool = params.INITIAL_TOOL|default(default_toolhead)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	
	
	
	
	
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(printer.heater_bed.target, true)|float %}
	
	
	{% set total_layer_count = params.TOTAL_LAYER_COUNT|default(0)|int %}
	{% set extruder_first_layer_temp = (params.EXTRUDER_TEMP|default("")).split(",") %}
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL BEACON_CONTACT_START_PRINT_TRUE_ZERO={beacon_contact_start_print_true_zero} BEACON_CONTACT_CALIBRATE_MODEL_ON_TRUE_ZERO={beacon_contact_calibrate_model_on_true_zero}
	{% endif %}
	
	_START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH BED_TEMP={bed_temp}
	
	
	RATOS_ECHO MSG="First print coordinates X:{first_x} Y:{first_y}"
	
	
	{% if params.TOTAL_LAYER_COUNT is not defined %}
	{% set link_url = "https://os.ratrig.com/docs/slicers" %}
	{% set link_text = "RatOS Slicer Configuration" %}
	{% set line_1 = '"Your slicer gcode settings are not up to date._N_Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="Incomplete Slicer Configuration detected" TYPE="warning" MSG={line_1}
	{% endif %}
	
	
	SET_PRINT_STATS_INFO CURRENT_LAYER=1
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE=1
	{% if total_layer_count > 0 %}
	SET_PRINT_STATS_INFO TOTAL_LAYER={total_layer_count}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads %}
	{% set initial_tool = 0 if initial_tool == 1 else 1 %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	{% endif %}
	
	
	{% set both_toolheads = true %}
	{% if total_toolshifts == 0 %}
	{% set both_toolheads = false %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	{% endif %}
	{% if both_toolheads and (idex_mode == "copy" or idex_mode == "mirror") %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Gcode tool changes found. Copy and mirror mode do not support toolchanges.")}
	{% endif %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set both_toolheads = true %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=initial_tool VALUE={initial_tool}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_x VALUE={first_x}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_y VALUE={first_y}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=total_toolshifts VALUE={total_toolshifts}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=both_toolheads VALUE={both_toolheads}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_first_layer_temp VALUE="'{params.EXTRUDER_TEMP}'"
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_other_layer_temp VALUE="'{params.EXTRUDER_OTHER_LAYER_TEMP}'"
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE=0
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set svv = printer.save_variables.variables %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set stepper_x_position_min = printer.fastconfig.settings.stepper_x.position_min|float %}
	{% set stepper_x_position_endstop = printer.fastconfig.settings.stepper_x.position_endstop|float %}
	{% set dual_carriage_position_max = printer.fastconfig.settings.dual_carriage.position_max|float %}
	{% set dual_carriage_position_endstop = printer.fastconfig.settings.dual_carriage.position_endstop|float %}
	{% set x_parking_space = parking_position_t0 - (stepper_x_position_endstop , stepper_x_position_min)|max %}
	{% set dc_parking_space = (dual_carriage_position_endstop , dual_carriage_position_max)|min - parking_position_t1 %}
	{% if svv.idex_xoffset|abs >= (x_parking_space - 0.5) or svv.idex_xoffset|abs >= (dc_parking_space - 0.5) %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Toolhead x-offset is too high for the available parking space. Calibrate your X and DC endstop positions and make sure you stay below 1mm." % (copy_mode_max_width)) }
	{% endif %}
	{% endif %}
	
	
	{% if (idex_mode == "copy" or idex_mode == "mirror") and printer.fastconfig.settings.ratos.enable_gcode_transform %}
	
	{% if params.MIN_X is not defined or params.MAX_X is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Something went wrong! Missing important post processor start print parameter!") }
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE=0
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	
	{% set boundary_box_min_x = params.MIN_X|default(0)|float %}
	{% set boundary_box_max_x = params.MAX_X|default(printable_x_max)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if default_toolhead == 0 %}
	
	{% set boundary_box_max_x = boundary_box_max_x + svv.idex_xoffset %}
	{% else %}
	
	{% set boundary_box_min_x = boundary_box_min_x - svv.idex_xoffset %}
	{% endif %}
	
	{% set center_x = printable_x_max / 2.0 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set object_width = boundary_box_max_x - boundary_box_min_x %}
	{% set copy_mode_max_width = center_x %}
	{% set mirror_mode_max_width = center_x - safe_distance / 2.0 %}
	
	DEBUG_ECHO PREFIX="START_PRINT" MSG="OBJECT_WIDTH: {object_width} BOUNDARY_BOX_MIN_X: {boundary_box_min_x} BOUNDARY_BOX_MAX_X: {boundary_box_max_x} CENTER_X: {center_x} SAFE_DISTANCE: {safe_distance}"
	
	
	{% if idex_mode == "copy" and object_width > copy_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for copy mode! Max supported width is %s mm" % (copy_mode_max_width)) }
	{% endif %}
	{% if idex_mode == "mirror" and object_width > mirror_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for mirror mode! Max supported width is %s mm" % (mirror_mode_max_width)) }
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = (printable_x_max - boundary_box_max_x - boundary_box_min_x) / 2 %}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE={object_xoffset}
	{% endif %}
	
	{% endif %}
	
	
	{% set has_initial_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_toolhead_filament_sensor %}
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% set has_initial_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_bowden_filament_sensor %}
	
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% if printer["dual_carriage"] is defined and both_toolheads %}
	
	{% set has_secondary_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set has_secondary_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_CHAMBER_FILTER_ON AT="before_print_start"
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true' %}
	{% if both_toolheads %}
	RATOS_ECHO MSG="Spool join is not possible if both toolheads are in use!"
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	{% endif %}
	
	
	CLEAR_PAUSE
	{% if printer["gcode_macro RatOS"].force_absolute_position|lower == 'true' %}
	G90
	{% endif %}
	SAVE_GCODE_STATE NAME=start_print_state
	
	
	G21
	
	G90
	
	M82
	_USER_START_PRINT_BEFORE_HOMING { rawparams }
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_BEGIN_BATCH
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_Z_HOP
	
	
	{% if idex_mode != '' and not (printer.fastconfig.settings.beacon is defined and (beacon_contact_start_print_true_zero or beacon_adaptive_heat_soak)) %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	{% if chamber_temp > 0 %}
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED={printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float}
	{% endif %}
	{% endif %}
	_CHAMBER_HEATER_ON START_CHAMBER_TEMP={start_chamber_temp} CHAMBER_TEMP={chamber_temp}
	_USER_START_PRINT_HEAT_CHAMBER { rawparams } CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_START_PRINT_BEFORE_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	RATOS_ECHO MSG="Heating bed..."
	
	M190 S{bed_temp}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_adaptive_heat_soak %}
	_MOVE_TO_SAFE_Z_HOME
	
	G1 Z2.5 F{z_speed}
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK LAYER_QUALITY={beacon_adaptive_heat_soak_layer_quality} MAXIMUM_FIRST_LAYER_DURATION={beacon_adaptive_heat_soak_maximum_first_layer_duration} MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={beacon_adaptive_heat_soak_max_wait}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_BED { rawparams }
	
	
	_START_PRINT_AFTER_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	_USER_START_PRINT_BED_MESH { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_BED_MESH X0={X0} X1={X1} Y0={Y0} Y1={Y1} T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_END_BATCH
	{% endif %}
	
	
	{% if idex_mode == '' %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[initial_tool]|float}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[0]|float}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={extruder_first_layer_temp[1]|float}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_PARK { rawparams }
	
	
	_START_PRINT_PARK
	
	
	RATOS_ECHO MSG="Heating Extruder..."
	{% if idex_mode == '' %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[initial_tool]|float}  MAXIMUM={extruder_first_layer_temp[initial_tool]|float + 5}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[0]|float}  MAXIMUM={extruder_first_layer_temp[0]|float + 5}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder1" MINIMUM={extruder_first_layer_temp[1]|float}  MAXIMUM={extruder_first_layer_temp[1]|float + 5}
	{% endif %}
	{% endif %}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	{% if idex_mode == '' %}
	_LED_PRINTING
	{% else %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	_LED_PRINTING
	{% else %}
	{% if both_toolheads %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	{% if toolchange_standby_temp > -1 %}
	_LED_TOOLHEAD_STANDBY TOOLHEAD={0 if initial_tool == 1 else 1}
	{% else %}
	_LED_PRINTING TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% else %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_EXTRUDER { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_AFTER_HEATING_EXTRUDER X0={X0} X1={X1} Y0={Y0} Y1={Y1} INITIAL_TOOLHEAD={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if idex_mode != '' %}
	{% if not both_toolheads %}
	{% if initial_tool != default_toolhead %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if idex_mode != '' %}
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=standby VALUE=False
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=standby VALUE=False
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if initial_tool == 1 else 'extruder1'} TARGET={toolchange_standby_temp}
	SET_GCODE_VARIABLE MACRO=T{0 if initial_tool == 1 else 1} VARIABLE=standby VALUE=True
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=start_print_state
	
	{% if printer["dual_carriage"] is defined %}
	_SET_IDEX_MODE_OFFSET
	{% endif %}
	
	
	{% if idex_mode != '' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% if idex_mode == "copy" and idex_mode != act_idex_mode %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == "mirror" and idex_mode != act_idex_mode %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={object_xoffset} MOVE=0
	{% endif %}
	{% else %}
	_SELECT_TOOL T={initial_tool} TOOLSHIFT=false
	_SET_TOOLHEAD_OFFSET
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	_SET_EXTRUSION_MODE
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={printer["print_stats"].print_duration}
	{% endif %}
	
	
	_USER_END_START_PRINT { rawparams }
	
	G92 E0
	
	
	_CHAMBER_FILTER_ON AT="after_print_start"
	
	_ALERT_NON_ZERO_Z_OFFSET
	
	RATOS_ECHO MSG="Printing..."

[gcode_macro _START_PRINT_BEFORE_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set is_stowable_probe = true if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' else false %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Pre-heating extruder..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={min_temp}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET={min_temp}
	{% endif %}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	{% endif %}
	{% endif %}
	
	
	{% if not is_stowable_probe %}
	{% if printer["dual_carriage"] is defined and act_t != default_toolhead %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	{% endif %}
	RATOS_ECHO MSG="Heat soaking z probe..."
	_MOVE_TO_SAFE_Z_HOME
	
	G0 Z2 F{z_speed}
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Waiting for extruder to be preheated..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	{% if default_toolhead == 0 %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_Z_HOP
	{% endif %}
	
	
	{% if auto_z_offset_calibration %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	PARK_TOOLHEAD
	_CLEANING_MOVE TOOLHEAD={default_toolhead} AUTOMATED=True
	_SELECT_TOOL T={0 if default_toolhead == 1 else 1} X={parking_position_t0 if default_toolhead == 1 else parking_position_t1} Y=0 TOOLSHIFT=false
	_CLEANING_MOVE TOOLHEAD={0 if default_toolhead == 1 else 1} AUTOMATED=True
	_VAOC_CALIBRATE_Z_OFFSET AUTO_Z_OFFSET=True
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=false
	{% endif %}
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	{% if needs_rehoming %}
	G28 Z
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	_START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE
	{% endif %}
	{% endif %}
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	PROBE PROBE_METHOD=contact SAMPLES=1

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	{% set fuzzy_radius = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_radius|default(0)|float if beacon_contact_start_print_true_zero_fuzzy_position else 0 %}
	
	{% set contact_true_zero_temp_has_been_set = False %}
	
	
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	
	
	
	{% if printer.beacon.last_probe_result|lower == "ok" %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	RATOS_ECHO MSG="Auto calibration nozzle wipe with probe result {last_z_offset}..."
	G0 Z{(0.2 + last_z_offset)} F{z_speed}
	G0 X70 F300
	{% else %}
	RATOS_ECHO MSG="Skipping auto calibration nozzle wipe because probing failed!"
	{% endif %}
	{% elif beacon_contact_wipe_before_true_zero_method == "probe_clean" %}
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	
	{% set contact_true_zero_temp_has_been_set = True %}
	
	
	
	
	
	
	
	
	BEACON_PROBE_CLEAN X=50 Y=10
	{% else %}
	CONSOLE_ECHO TYPE="error" TITLE="Unknown wipe method" MSG="Unknown wipe method '{beacon_contact_wipe_before_true_zero_method}' configured, skipping wipe before beacon true zero."
	{% endif %}
	{% endif %}
	
	
	G0 Z5 F{z_speed}
	_MOVE_TO_SAFE_Z_HOME FUZZY_RADIUS={fuzzy_radius}
	
	
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION
	
	{% if not contact_true_zero_temp_has_been_set %}
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon contact auto calibration..."
	
	{% if beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	
	G0 Z5 F{z_speed}

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION]
gcode = 
	{% set pos = printer.ratos.last_move_to_safe_z_home_position %}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE={pos[0]}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE={pos[1]}

[gcode_macro _START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set first_x = printer["gcode_macro START_PRINT"].first_x|default(-1)|float %}
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2.0 %}
	{% set center_y = printable_y_max / 2.0 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% if printer["dual_carriage"] is defined %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% endif %}
	
	
	{% set X0 = params.X0|default(-1)|int %}
	{% set X1 = params.X1|default(-1)|int %}
	{% set Y0 = params.Y0|default(-1)|int %}
	{% set Y1 = params.Y1|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	
	{% if idex_mode == '' %}
	
	_PRIME
	{% else %}
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	RATOS_ECHO PREFIX="IDEX" MSG="using combined prime offset for IDEX {idex_mode} mode"
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	{% if both_toolheads %}
	{% if initial_toolhead == 0 %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T{initial_toolhead}"
	_SELECT_TOOL T={initial_toolhead} TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	SET_MACRO_TRAVEL_SETTINGS
	
	{% if (X0 > -1 and Y1 > -1) or (first_x > 0 and first_y > 0) %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	{% endif %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	{% set first_z = 1 %}
	{% else %}
	{% set first_z = 3 %}
	{% endif %}
	
	
	{% if idex_mode == "mirror" %}
	{% if first_y >= 0 %}
	G0 Y{first_y} F{speed}
	{% else %}
	G0 Y{Y1} F{speed}
	{% endif %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={initial_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={initial_toolhead} E={printer["gcode_macro RatOS"].toolchange_first_purge|default(50)|float}
	_CLEANING_MOVE TOOLHEAD={initial_toolhead} AUTOMATED=True
	{% endif %}
	{% if first_x >= 0 and first_y >= 0 %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% else %}
	{% set first_x = X0 %}
	{% set first_y = Y0 %}
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'min' %}
	{% set first_x = X0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'max' %}
	{% set first_x = X1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|float <= center_x %}
	{% set first_x = X0 %}
	{% else %}
	{% set first_x = X1 %}
	{% endif %}
	{% endif %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'min' %}
	{% set first_y = Y0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'max' %}
	{% set first_y = Y1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|float <= center_y %}
	{% set first_y = Y0 %}
	{% else %}
	{% set first_y = Y1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	
	
	_LOAD_RATOS_SKEW_PROFILE

[gcode_macro _PRIME]
gcode = 
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	PRIME_BLOB INITIAL_TOOLHEAD={params.INITIAL_TOOLHEAD} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={params.IDEX_MODE} Y1={params.Y1}
	{% else %}
	
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif params.IDEX_MODE == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro END_PRINT]
description = End print procedure, use this in your Slicer.
gcode = 
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SAVE_GCODE_STATE NAME=end_print_state
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = printer["gcode_macro START_PRINT"].object_xoffset|default(0)|float %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(0-object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={(0-object_xoffset)}
	{% endif %}
	{% endif %}
	
	
	_USER_END_PRINT_BEFORE_HEATERS_OFF { rawparams }
	_END_PRINT_BEFORE_HEATERS_OFF
	TURN_OFF_HEATERS
	_USER_END_PRINT_AFTER_HEATERS_OFF { rawparams }
	_END_PRINT_AFTER_HEATERS_OFF
	_USER_END_PRINT_PARK { rawparams }
	_END_PRINT_PARK
	
	
	{% if printer["gcode_macro RatOS"].skew_profile is defined %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined and printer["gcode_macro RatOS"].end_print_motors_off|lower != 'false' %}
	
	M84
	{% endif %}
	
	
	M107
	
	
	BED_MESH_CLEAR
	RATOS_ECHO MSG="Done :)"
	
	
	RESTORE_GCODE_STATE NAME=end_print_state
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	M84
	{% endif %}
	
	
	RESET_NAMED_OFFSET EVENT="end_print"
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_CHAMBER_FILTER_ON AT="print_end"
	_CHAMBER_FILTER_OFF
	
	
	_CHAMBER_HEATER_OFF
	
	_USER_END_PRINT_FINISHED { rawparams }

[gcode_macro _END_PRINT_BEFORE_HEATERS_OFF]
gcode = 
	RATOS_ECHO MSG="Cleaning up..."

[gcode_macro _END_PRINT_AFTER_HEATERS_OFF]
gcode = 
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% set z_hop = printer["gcode_macro RatOS"].end_print_park_z_hop|float %}
	{% set r = printer["gcode_macro RatOS"].end_print_retract_filament|default(4)|float %}
	{% if current_z < (max_z - z_hop) %}
	{% set z_safe = z_hop %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G91
	
	{% if can_extrude %}
	G1 E-2 F3600
	{% endif %}
	
	G0 Z{z_safe} F3600
	
	{% if can_extrude %}
	G1 E-{(r-2)} F3600
	{% endif %}
	
	G90

[gcode_macro _SET_EXTRUSION_MODE]
gcode = 
	
	{% if printer["gcode_macro RatOS"].relative_extrusion|lower == 'true' %}
	M83
	{% else %}
	M82
	{% endif %}

[gcode_macro GENERATE_SHAPER_GRAPHS]
description = Genarates input shaper resonances graphs for analysis. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	{% set hz_per_sec = params.HZ_PER_SEC|default(1)|float %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set copy_mode_offset = printable_x_max / 4.0 %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	_IDEX_SINGLE
	{% endif %}
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	
	
	{% if idex_mode != 'copy' and idex_mode != 'mirror' %}
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	{% endif %}
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Shaper graph"

[gcode_shell_command generate_shaper_graph_x]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-x.sh
timeout = 60.
verbose = True

[gcode_shell_command generate_shaper_graph_y]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-y.sh
timeout = 60.
verbose = True

[gcode_macro MEASURE_COREXY_BELT_TENSION]
description = Generates resonance graph used to ensure belts are equally tensioned. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	_IDEX_SINGLE
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if measure_t1 == false or measure_t0 == false %}
	{action_raise_error("Axis specified. Not supported for belt tension on Y.")}
	{% else %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	G4 P5000
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	PARK_TOOLHEAD
	{% endif %}
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	G1 X{parking_position_t1} F{speed}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	
	
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Belt Tension Graph"

[gcode_shell_command generate_belt_tension_graph]
command = /home/pi/printer_data/config/RatOS/scripts/generate-belt-tension-graph.sh
timeout = 90.
verbose = True

[idle_timeout]
gcode = 
	{% if printer.webhooks.state|lower == 'ready' %}
	{% if printer.pause_resume.is_paused|lower == 'false' %}
	_USER_BEFORE_IDLE_TIMEOUT
	RATOS_ECHO PREFIX="IDLE" MSG="2 hours since last activity. Powering off heaters and motors.."
	TURN_OFF_HEATERS
	M84
	_USER_AFTER_IDLE_TIMEOUT
	{% endif %}
	{% endif %}
timeout = 7200

[temperature_sensor raspberry_pi]
sensor_type = temperature_host

[skew_correction]

[named_offsets]

[input_shaper]

[virtual_sdcard]
path = ~/printer_data/gcodes

[display_status]

[pause_resume]

[force_move]
enable_force_move = True

[respond]

[resonance_generator]

[ratos]
allow_unknown_gcode_generator = True
enable_gcode_transform = True

[exclude_object]

[bed_mesh]
split_delta_z = 0.001
horizontal_move_z = 2
mesh_min = 20,20
mesh_max = 480,480
probe_count = 40,40
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = .2
speed = 600
log_points = False

[fastconfig]

[heater_bed]
heater_pin = heater_bed_heating_pin
sensor_pin = heater_bed_sensor_pin
sensor_type = Generic 3950
min_temp = 0
max_temp = 140
pwm_cycle_time = 0.103
control = pid
pid_kp = 61.987
pid_ki = 1.781
pid_kd = 539.289

[printer]
kinematics = ratos_hybrid_corexy
max_velocity = 800
max_accel = 10000
minimum_cruise_ratio = 0.5
max_z_velocity = 50
max_z_accel = 600
square_corner_velocity = 5

[ratos_hybrid_corexy]
inverted = true

[dual_carriage]
axis = x
safe_distance = 55
position_max = 559.6
position_endstop = 559.6
position_min = 0
step_pin = PF9
dir_pin = dual_carriage_dir_pin
enable_pin = !PG2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t1:PA2

[gcode_macro _SET_IDEX_MODE_OFFSET]
description = "Internal use only. Sets the 'idex_mode' named offset that the active idex mode requires."
gcode = 
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_SET_IDEX_MODE_OFFSET" MSG="idex_mode: {idex_mode}, center_x: {center_x}"
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	SET_NAMED_OFFSET NAME=idex_mode X={(-center_x / 2)}
	{% else %}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% else %}
	{action_raise_error("_SET_IDEX_MODE_OFFSET: Printer not homed")}
	{% endif %}

[gcode_macro IDEX_SINGLE]
gcode = 
	_IDEX_REMAP_TOOLHEADS ENABLE=False
	_IDEX_SINGLE

[gcode_macro _IDEX_SINGLE]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_single"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set init = params.INIT|default(0)|int %}
	{% set new_x = params.X|default(-1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_default_t = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="init: {init}, new_x: {new_x}, idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, act_t: {act_t}"
	
	{% if idex_mode == "copy" or idex_mode == "mirror" or init == 1 %}
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="reset idex_mode offset"
	G1 X{center_x} F{(speed)}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="activate default carriage"
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolheads"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	G90
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position."
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1}
	G1 X{parking_position_default_t} F{speed}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move default toolhead to its new position."
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% if new_x == -1 %}
	{% set new_x = center_x %}
	{% endif %}
	G1 X{new_x} F{speed}
	
	M400
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="X Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set extruder motion queue."
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if default_toolhead==0 else default_toolhead}
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolhead offset."
	_SET_TOOLHEAD_OFFSET
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set input shaper."
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[default_toolhead]|float)} SHAPER_FREQ_Y={(shaper_y_freq[default_toolhead]|float)} SHAPER_TYPE_X={(shaper_x_type[default_toolhead]|lower)} SHAPER_TYPE_Y={(shaper_y_type[default_toolhead]|lower)}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="update Frontend."
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if default_toolhead==0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if default_toolhead==1 else False}
	{% else %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_single"

[gcode_macro IDEX_COPY]
gcode = 
	_IDEX_COPY

[gcode_macro _IDEX_COPY]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_copy"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set y = params.Y|default(-1)|int %}
	{% set dance = params.DANCE|default(1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_COPY" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}, y: {y}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "copy" %}
	{% if idex_mode == "mirror" %}
	{% if y>=0 %}
	G1 X{center_x} Y{y} F{(speed)}
	{% else %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	
	
	{% if idex_mode != "mirror" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance == 1 %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[2]|float)} SHAPER_FREQ_Y={(shaper_y_freq[2]|float)} SHAPER_TYPE_X={(shaper_x_type[2]|lower)} SHAPER_TYPE_Y={(shaper_y_type[2]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_copy"

[gcode_macro IDEX_MIRROR]
gcode = 
	_IDEX_MIRROR

[gcode_macro _IDEX_MIRROR]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_mirror"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set dance = params.DANCE|default(1)|int %}
	{% set priming = params.PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_MIRROR" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "mirror" %}
	
	{% if idex_mode == "copy" %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS MIRROR_PRIMING={params.PRIMING}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=MIRROR
	
	
	{% if idex_mode != "copy" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance and not priming %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[3]|float)} SHAPER_FREQ_Y={(shaper_y_freq[3]|float)} SHAPER_TYPE_X={(shaper_x_type[3]|lower)} SHAPER_TYPE_Y={(shaper_y_type[3]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_mirror"

[gcode_macro _IDEX_SET_TOOLHEADS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set mirror_priming = params.MIRROR_PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position_inactive_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_IDEX_SET_TOOLHEADS" MSG="idex_mode: {idex_mode}, act_t: {act_t}, center_x: {center_x}, mirror_priming: {mirror_priming}"
	
	
	{% if act_t != default_toolhead %}
	_SET_TOOLHEAD_OFFSET FORCE_TOOLHEAD={default_toolhead} MOVE=1
	{% endif %}
	
	{% if mirror_priming %}
	
	
	
	{% if parking_position_t0|abs < parking_position_t1 - printable_x_max %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{printable_x_max + parking_position_t0|abs} F{(speed)}
	{% else %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{0 - (parking_position_t1 - printable_x_max)} F{(speed)}
	{% endif %}
	
	{% else %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1} MODE=PRIMARY
	G1 X{parking_position_inactive_t} F{(speed)}
	
	
	{% if act_t==1 %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{center_x / 2} F{(speed)}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"

[gcode_macro IDEX_PARK]
gcode = 
	
	PARK_TOOLHEAD

[gcode_macro PARK_TOOLHEAD]
gcode = 
	
	{% set idex_mode = 'none' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="PARK_TOOLHEAD" MSG="Parking T{act_t}.."
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set parking_position_inact_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set printable_y_min = printer["gcode_macro RatOS"].printable_y_min|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" and 'xy' in printer.toolhead.homed_axes %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% elif printer.toolhead.position.y|float < printable_y_min %}
	G1 Y{printable_y_min} F{speed}
	{% endif %}
	
	SAVE_GCODE_STATE NAME=_PARK_TOOLHEAD
	G90
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0.5
	
	
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_inact_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	
	SET_VELOCITY_LIMIT ACCEL={printer.toolhead.max_accel} MINIMUM_CRUISE_RATIO=0.5
	M400
	RESTORE_GCODE_STATE NAME=_PARK_TOOLHEAD
	
	{% endif %}

[gcode_macro JOIN_SPOOLS]
gcode = 
	
	{% set spools = params.SPOOLS|default("") %}
	
	{% if spools == "" %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% else %}
	{% if spools != "0,1" and spools != "1,0" %}
	RATOS_ECHO MSG="Wrong spool configuration!"
	RATOS_ECHO MSG="Join Spools = JOIN_SPOOLS SPOOLS=0,1"
	RATOS_ECHO MSG="Deactivate = JOIN_SPOOLS SPOOLS="
	{% else %}
	{% if spools == "0,1" or spools == "1,0" %}
	_IDEX_JOIN_SPOOLS ENABLE=true
	{% else %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_JOIN_SPOOLS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if enable %}
	{% set has_t0_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t1_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t0_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined else false %}
	{% set has_t1_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined else false %}
	{% if (has_t0_toolhead_filament_sensor and has_t1_toolhead_filament_sensor) or (has_t0_bowden_filament_sensor and has_t1_bowden_filament_sensor) %}
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=True
	RATOS_ECHO MSG="Spool joining enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Can not enable spool joining! No filament sensors found."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining deactivated!"
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining is not possible in copy and mirror mode!"
	{% endif %}

[gcode_macro _JOIN_SPOOL]
gcode = 
	
	{% set old_toolhead = params.TOOLHEAD|int %}
	{% set new_toolhead = 0 if old_toolhead == 1 else 1 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set purge_after_load = printer["gcode_macro T%s" % new_toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_JOIN_SPOOL" MSG="toolhead: {new_toolhead}"
	
	{% set has_filament = true %}
	{% set has_new_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% set has_new_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% if has_new_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	{% if has_new_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	
	{% if has_filament %}
	RATOS_ECHO MSG="Joining spools! Please wait for extruder to heat up...."
	
	
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={new_toolhead}
	
	
	_DEACTIVATE_TOOLHEAD TOOLHEAD={old_toolhead}
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set extruder_temp = extruder_first_layer_temp[new_toolhead]|float %}
	{% else %}
	{% set extruder_temp = extruder_other_layer_temp[new_toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if new_toolhead == 0 else 'extruder1'} TARGET={extruder_temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if new_toolhead == 0 else 'extruder1'} MINIMUM={extruder_temp}  MAXIMUM={extruder_temp + 5}
	
	
	{% if purge_after_load > 0 %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_toolhead == 0 else new_toolhead}
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={new_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={new_toolhead} E={purge_after_load}
	_CLEANING_MOVE TOOLHEAD={new_toolhead} AUTOMATED=True
	
	
	SET_DUAL_CARRIAGE CARRIAGE={old_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if old_toolhead == 0 else old_toolhead}
	
	{% endif %}
	
	
	RESUME TOOLHEAD={new_toolhead}
	
	
	_IDEX_JOIN_SPOOLS ENABLE=false
	
	{% else %}
	{ action_raise_error("Spool join failed! No filament found or filament sensor is disabled.") }
	{% endif %}

[gcode_macro REMAP_TOOLHEADS]
gcode = 
	
	{% set toolheads = params.TOOLHEADS|default("") %}
	
	{% if toolheads == "" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% else %}
	{% if toolheads != "0,1" and toolheads != "1,0" %}
	RATOS_ECHO MSG="Wrong toolhead configuration!"
	RATOS_ECHO MSG="Remap = REMAP_TOOLHEADS TOOLHEADS=0,1"
	RATOS_ECHO MSG="Deactivate = REMAP_TOOLHEADS TOOLHEADS="
	{% else %}
	{% if toolheads == "0,1" or toolheads == "1,0" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=true
	_IDEX_SINGLE
	{% else %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_REMAP_TOOLHEADS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	{% if not enable or (idex_mode != "copy" and idex_mode != "mirror") %}
	{% if enable %}
	RATOS_ECHO MSG="Toolhead remapping enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping deactivated!"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE={enable}
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping not possible in copy and mirror mode!"
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	{% endif %}

[gcode_macro SHAPER_CALIBRATE]
rename_existing = SHAPER_CALIBRATE_ORG
gcode = 
	RATOS_ECHO PREFIX="IDEX" MSG="SHAPER_CALIBRATE is useless on IDEX machines. Please use the GENERATE_SHAPER_GRAPHS macro and type the values into `variable_shaper_*_freq` and `variable_shaper_*_type manually`."

[gcode_shell_command generate_shaper_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-shaper-graph.sh
timeout = 120.
verbose = True

[gcode_shell_command generate_tension_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-belt-tension-graph.sh
timeout = 120.
verbose = True

[gcode_macro SET_PRESSURE_ADVANCE]
variable_snyc_toolheads = False
rename_existing = SET_PRESSURE_ADVANCE_BASE
gcode = 
	{% if params.SYNC_TOOLHEADS is defined %}
	{% set snyc_toolheads = true if params.SYNC_TOOLHEADS|default(false)|lower == 'true' else false %}
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=True
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="Syncing toolheads..."
	{% else %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' or snyc_toolheads %}
	{% set advance = params.ADVANCE|default(printer['extruder'].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['extruder'].smooth_time|float)|float %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T0"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T1"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder1' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% else %}
	{% set extruder = 'extruder' if act_t == 0 else 'extruder1' %}
	{% if params.EXTRUDER is defined %}
	{% set extruder = params.EXTRUDER %}
	{% endif %}
	{% if extruder == 'extruder' or extruder == 'extruder1' %}
	{% set advance = params.ADVANCE|default(printer['%s' % extruder].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['%s' % extruder].smooth_time|float)|float %}
	SET_PRESSURE_ADVANCE_BASE EXTRUDER={extruder} ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% if params.EXTRUDER is not defined %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG={"T%s" % act_t}
	{% endif %}
	{% else %}
	SET_PRESSURE_ADVANCE_BASE { rawparams }
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro M106]
rename_existing = M106.1
variable_swap_speed = -1
gcode = 
	
	{% set s = [[params.S|default(255)|int, 255]|min, 0]|max %}
	{% set p = params.P|default(-1)|int %}
	{% set speed = s / 255 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set t = 1 if idex_mode=='primary' else 0 %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(0)|int == 1 else false %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set sync_fans = true %}
	{% endif %}
	
	
	{% if sync_fans and idex_mode != "copy" and idex_mode != "mirror" %}
	
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int %}
	
	
	{% if toolshift_count > total_toolshifts %}
	{% set sync_fans = false %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE=-1
	
	
	{% if p == -1 %}
	
	{% if speed == 0 %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed}
	{% else %}
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE={speed}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={(speed if (t == 0 or sync_fans) else 0)}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={(speed if (t == 1 or sync_fans) else 0)}
	{% endif %}
	{% else %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed if t == p else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed if t == p else 0}
	{% endif %}
	
	
	M106.1 S{s}

[gcode_macro M107]
rename_existing = M107.1
gcode = 
	{% set p = params.P|default(-1)|int %}
	M106 S0 P{p}

[gcode_macro _SELECT_TOOL]
variable_last_timestamp = 0
gcode = 
	{% if params.T is defined %}
	{% set idex_mode = '' %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if "xyz" not in printer.toolhead.homed_axes and (idex_mode == "copy" or idex_mode == "mirror") %}
	_IDEX_SINGLE
	{% set idex_mode = 'reset' %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set new_t = params.T|int %}
	
	
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads and is_printing_gcode %}
	{% set new_t = 0 if new_t == 1 else 1 %}
	{% endif %}
	
	
	{% set toolchange_prepurging_timer = printer["gcode_macro RatOS"].toolchange_prepurging_timer|default(0)|int %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	DEBUG_ECHO PREFIX="_SELECT_TOOL" MSG="act_t: {act_t}, new_t: {new_t}, is_printing_gcode: {is_printing_gcode}, swap_toolheads: {swap_toolheads}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	{% set act_extruder = 'extruder%s' % ('' if new_t == 0 else new_t) %}
	{% if new_t != act_t or printer.toolhead.extruder != act_extruder or idex_mode == 'reset' %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Selecting T{new_t}.."
	
	
	M220 S100
	
	
	
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(1)|int == 1 else false %}
	
	
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set toolshift = false %}
	{% endif %}
	
	
	{% set fan_speed = printer["fan_generic part_fan_t%s" % act_t].speed %}
	
	
	{% set deactivate_toolhead = false %}
	{% if is_printing_gcode %}
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int + 1 %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE={toolshift_count}
	{% if toolshift_count == total_toolshifts %}
	{% set deactivate_toolhead = true %}
	{% endif %}
	{% endif %}
	
	
	{% set needs_wakeup = true if printer["gcode_macro T%s" % new_t].standby|default(false)|lower == 'true' else false %}
	
	
	{% set needs_purging = false %}
	{% set wake_up_purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% if is_printing_gcode and toolchange_prepurging_timer > 0 and wake_up_purge > 0 %}
	{% set new_timestamp = printer["print_stats"].print_duration %}
	{% set elapsed_time = new_timestamp - last_timestamp %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={new_timestamp}
	{% if elapsed_time > toolchange_prepurging_timer %}
	{% set needs_purging = true %}
	{% endif %}
	{% endif %}
	
	
	{% set first_use_purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% if toolshift_count == 1 and first_use_purge > 0 %}
	{% set needs_purging = true %}
	{% endif %}
	
	
	{% if is_printing_gcode and (toolchange_standby_temp > -1 or needs_purging or needs_wakeup) %}
	_TOOLHEAD_STANDBY TOOLHEAD={act_t}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	_TOOLHEAD_WAKEUP TOOLHEAD={new_t} X={new_x} Y={new_y} Z={new_z} FAN_SPEED={fan_speed} TOOLSHIFT_COUNT={toolshift_count}
	{% else %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(false)|lower == 'true' else false %}
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if (new_t == 0 or sync_fans) else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if (new_t == 1 or sync_fans) else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	_TOOLCHANGE T={new_t} X={new_x} Y={new_y} Z={new_z} PARK_T0={park_t0} PARK_T1={park_t1} TOOLSHIFT={toolshift}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[new_t]|float)} SHAPER_FREQ_Y={(shaper_y_freq[new_t]|float)} SHAPER_TYPE_X={(shaper_x_type[new_t]|lower)} SHAPER_TYPE_Y={(shaper_y_type[new_t]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if new_t == 0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if new_t == 1 else False}
	
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% set sanity_check_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if new_t == 0 %}
	{% if printer.toolhead.extruder == 'extruder' %}
	{% if sanity_check_idex_mode == 'primary' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% elif new_t == 1 %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% if sanity_check_idex_mode == 'inactive' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _TOOLHEAD_STANDBY]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Putting toolhead T{toolhead} into standby mode."
	DEBUG_ECHO PREFIX="_TOOLHEAD_STANDBY" MSG="toolhead: {toolhead}, config_z_hop: {config_z_hop}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={toolhead} SYNC=0
	PARK_TOOLHEAD
	
	
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={toolchange_standby_temp}
	{% endif %}
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=True
	{% endif %}
	
	
	_LED_TOOLHEAD_STANDBY TOOLHEAD={toolhead}

[gcode_macro _TOOLHEAD_WAKEUP]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set fan_speed = params.FAN_SPEED|float %}
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift_count = params.TOOLSHIFT_COUNT|default(0)|int %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% if toolshift_count == 1 %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% endif %}
	{% set needs_wakeup = true if printer["gcode_macro T%s" % toolhead].standby|default(false)|lower == 'true' else false %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Waking up toolhead T{toolhead}. Please wait for extruder to heat up..."
	DEBUG_ECHO PREFIX="_TOOLHEAD_WAKEUP" MSG="toolhead: {toolhead}, fan_speed: {fan_speed}, new_x: {new_x}, new_y: {new_y}, new_z: {new_z}, config_z_hop: {config_z_hop}"
	
	
	_LED_TOOLHEAD_WAKEUP TOOLHEAD={toolhead}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={toolhead} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE=1
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if toolhead == 0 else toolhead}
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if needs_wakeup %}
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set temp = extruder_first_layer_temp[toolhead]|float %}
	{% else %}
	{% set temp = extruder_other_layer_temp[toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if toolhead == 0 else 'extruder1'} MINIMUM={temp}  MAXIMUM={temp + 5}
	{% endif %}
	
	
	_LED_PRINTING TOOLHEAD={toolhead}
	
	
	{% if purge > 0 %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={toolhead} E={purge}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	
	
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if toolhead == 1 else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	G92 E0
	G1 E-{e} F{feedrate}
	G92 E0
	
	
	{% if new_x >= 0 and new_y >= 0 %}
	G1 X{new_x} Y{new_y} F{speed}
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={config_z_hop} T={toolhead} SYNC=0
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=False

[gcode_macro _TOOLCHANGE]
variable_toolshift_count = 0
gcode = 
	
	
	{% set new_t = params.T|default(-1)|int %}
	{% set new_x = params.X|default(-1.0)|float %}
	{% set new_y = params.Y|default(-1.0)|float %}
	{% set new_z = params.Z|default(-1.0)|float %}
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(true)|lower == 'true' else false %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T: {new_t}, X: {new_x}, Y: {new_y}, Z: {new_z}, PARK_T0: {park_t0}, PARK_T1: {park_t1}, IS_PRINTING_GCODE: {is_printing_gcode}, TOOLSHIFT: {toolshift}"
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	{% if park_t0 >= 0 and park_t1 >= 0 %}
	{% set parking_position_t0 = park_t0 %}
	{% set parking_position_t1 = park_t1 %}
	{% set parking_position_act_t = park_t0 if act_t == 0 else park_t1 %}
	{% endif %}
	
	
	{% if not is_printing_gcode and not toolshift %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Changing tool to T{new_t} without retracting/extruding or moving the toolheads except for parking."
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	G90
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% if not is_printing_gcode and toolshift and new_x < 0 and new_y < 0 %}
	{% set new_x = center_x %}
	{% set new_y = printer.gcode_move.gcode_position.y|float %}
	{% endif %}
	
	{% if new_x < 0 or new_y < 0 %}
	
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="No new X or Y position given, parking the active toolhead and activating the new toolhead without moving it."
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={new_t}
	
	
	{% if "x" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	{% if is_printing_gcode %}
	_EXTRUDE T={new_t}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	{% if "xyz" not in printer.toolhead.homed_axes %}
	
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	
	
	{% set svv = printer.save_variables.variables %}
	{% if new_t == default_toolhead %}
	{% set new_xoffset = 0 %}
	{% set new_yoffset = 0 %}
	{% set new_zoffset = 0 %}
	{% else %}
	{% set new_xoffset = -svv.idex_xoffset %}
	{% set new_yoffset = -svv.idex_yoffset %}
	{% set new_zoffset = -svv.idex_zoffset %}
	{% endif %}
	
	{% set xoffset_correction = new_xoffset - printer.named_offsets.toolhead_alignment.x %}
	{% set yoffset_correction = new_yoffset - printer.named_offsets.toolhead_alignment.y %}
	{% set zoffset_correction = new_zoffset - printer.named_offsets.toolhead_alignment.z %}
	
	{% if new_t == 0 %}
	
	{% set t0_act_x = parking_position_t0 %}
	{% set t1_act_x = printer.toolhead.position.x|float %}
	{% set t0_new_x = new_x %}
	{% set t1_new_x = parking_position_t1 %}
	{% set t0_distance = t0_new_x - t0_act_x %}
	{% set t1_distance = t1_new_x - t1_act_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T0."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	
	
	G1 X{t0_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x + (t1_new_x - t1_act_x)} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t0_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T0: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% elif new_t == 1 %}
	
	{% set t0_act_x = printer.toolhead.position.x|float %}
	{% set t1_act_x = parking_position_t1 %}
	{% set t0_new_x = parking_position_t0 %}
	{% set t1_new_x = new_x %}
	{% set t0_distance = t0_act_x - t0_new_x %}
	{% set t1_distance = t1_act_x - t1_new_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T1."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x - t1_distance + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t1_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T1: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% endif %}
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	{% endif %}

[gcode_macro _ZHOP_BEFORE_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_hop = params.Z_HOP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_HOP: {z_hop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="COMBINED_ZHOP G1 Z+{z_hop} E-{e} F{speed * 60}"
	G1 Z+{z_hop} E-{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="ZHOP G1 Z+{z_hop} F{speed * 60}"
	G1 Z+{z_hop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="RETRACT G1 E-{e} F{feedrate}"
	G1 E-{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _ZDROP_AFTER_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_drop = params.Z_DROP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_DROP: {z_drop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="COMBINED_ZDROP G1 Z-{z_drop} E{e} F{speed * 60}"
	G1 Z-{z_drop} E{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="ZDROP G1 Z-{z_drop} F{speed * 60}"
	G1 Z-{z_drop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="EXTRUDE G1 E{e} F{feedrate}"
	G1 E{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _EXTRUDE]
gcode = 
	
	{% set t = params.T|int %}
	
	
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	
	DEBUG_ECHO PREFIX="_EXTRUDE" MSG="G1 E{e} F{feedrate * 60}"
	
	
	G91
	M82
	G92 E0
	G1 E{e} F{feedrate * 60}
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _DEACTIVATE_TOOLHEAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_DEACTIVATE_TOOLHEAD" MSG="TOOLHEAD {toolhead}"
	
	
	{% if toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% endif %}
	
	
	M106.1 S0
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={toolhead}

[delayed_gcode _INIT_TOOLHEADS]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	_IDEX_SINGLE INIT=1
	
	
	{% if printer.fastconfig.settings.dual_carriage.safe_distance is defined %}
	{% if printer.fastconfig.settings.dual_carriage.safe_distance|float < 50 %}
	{ action_emergency_stop("Dual carriage safe_distance seems to be too low!") }
	{% endif %}
	{% else %}
	{ action_emergency_stop("Dual carriage safe_distance not defined!") }
	{% endif %}

[gcode_macro _SET_TOOLHEAD_OFFSET]
description = "Internal use only. Sets the toolhead_alignment offset (and hotend_thermal_expansion offset when configured) for the active/dominant toolhead."
gcode = 
	
	{% set move = params.MOVE|default(0)|int %}
	{% set force_toolhead = params.FORCE_TOOLHEAD|default(-1)|int %}
	
	
	{% if params.T is defined %}
	CONSOLE_ECHO TYPE="error" MSG="_SET_TOOLHEAD_OFFSET called with deprectated T parameter, which is ignored."
	{';$_SET_TOOLHEAD_OFFSET_ignoring_TOOLHEAD_parameter'}
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="active/dominant toolhead: {toolhead}, MOVE: {move}, FORCE_TOOLHEAD: {force_toolhead}"
	
	
	{% if force_toolhead >= 0 %}
	{% set toolhead = force_toolhead %}
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="FORCE_TOOLHEAD applied, using TOOLHEAD: {toolhead}"
	{% endif %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set move = 0 %}
	{% endif %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|int %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X=0 Y=0 MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z=0 MOVE={move} SPEED={z_speed}
	{% else %}
	{% set svv = printer.save_variables.variables %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X={(-svv.idex_xoffset)} Y={(-svv.idex_yoffset)} MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-svv.idex_zoffset)} MOVE={move} SPEED={z_speed}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}

[gcode_macro TOOLSHIFT_CONFIG]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={params.SPEED|default(300)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={params.ACCEL|default(5000)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_retraction VALUE={params.RETRACT|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_extrusion VALUE={params.EXTRUDE|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_feedrate VALUE={params.FEEDRATE|default(7200)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={params.Z_HOP|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zspeed VALUE={params.Z_SPEED|default(25)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_combined_zhop VALUE={true if params.COMBINED_ZHOP|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_sync_fans VALUE={true if params.SYNC_FANS|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_prepurging_timer VALUE={params.AUTO_PURGE_TIME|default(0)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_purge VALUE={params.PURGE|default(25)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_standby_temp VALUE={params.STANDBY_TEMP|default(-1)|float}

[gcode_macro CALCULATE_DC_ENDSTOP]
description = "DEPRECATED: This macro has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."
gcode = 
	CONSOLE_ECHO TITLE="CALCULATE_DC_ENDSTOP has been deprecated" TYPE="error" MSG="The CALCULATE_DC_ENDSTOP has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."

[gcode_macro _VAOC]
variable_is_fixed = True
variable_is_started = False
variable_is_started_at_temp = False
variable_additional_safe_distance = 50
variable_safe_z = 30
variable_auto_z_offset_calibration = True
variable_enable_camera_cooling = True
variable_camera_cooling_fan_speed = 0.3
variable_camera_cooling_temperature = 50
variable_toolchange_travel_speed = 300
variable_toolchange_travel_accel = 5000
variable_adjusting_secondary_toolhead_focus_adjusts_zoffset = False
variable_cache_toolchange_travel_speed = 300
variable_cache_toolchange_travel_accel = 5000
variable_cache_toolchange_zhop = 1.0
variable_t0_toolhead_sensor_enabled = 0
variable_t1_toolhead_sensor_enabled = 0
variable_t0_bowden_sensor_enabled = 0
variable_t1_bowden_sensor_enabled = 0
variable_loaded_skew_profile = ""
variable_gcode_z_offset = 0.0
variable_start_x_offset = 0.0
variable_start_y_offset = 0.0
gcode = 
	_ECHO_VAOC_VARS
variable_expected_camera_x_position = 212.5
variable_expected_camera_y_position = 530.5

[gcode_macro _VAOC_START]
description = Called from the front end. If T0_TEMP, T1_TEMP and BED_TEMP parameter are specified, VAOC calibration will start under real conditions at printing temp.
gcode = 
	
	{% set t0_temp = params.T0_TEMP|default(0)|int %}
	{% set t1_temp = params.T1_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(0)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro SKEW_PROFILE"].loaded_profile|default("") %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=loaded_skew_profile VALUE='"{loaded_skew_profile}"'
	
	
	{% if t0_temp > 0 and t1_temp > 0 and bed_temp > 0 %}
	
	
	{% if not is_fixed %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("VAOC calibration at temp works only with a fixed installed VAOC device.") }
	{% endif %}
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE=0
	{% endif %}
	
	
	START_PRINT EXTRUDER_TEMP={t0_temp},{t1_temp} EXTRUDER_OTHER_LAYER_TEMP={t0_temp},{t1_temp} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp} INITIAL_TOOL=0 TOTAL_LAYER_COUNT=1 X0={(printable_x_max / 2 - 10)} Y0={(printable_y_max / 2 - 10)} X1={(printable_x_max / 2 + 10)} Y1={(printable_y_max / 2 + 10)} TOTAL_TOOLSHIFTS=1 FIRST_X={printable_x_max / 2} FIRST_Y={printable_y_max / 2} MIN_X={(printable_x_max / 2 - 10)} MAX_X={(printable_x_max / 2 + 10)} USED_TOOLS=0,1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=True
	
	{% endif %}
	
	
	_START_VAOC

[gcode_macro _START_VAOC]
description = Called from _VAOC_START. Do not call it manually.
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(printable_x_max/2)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(printable_y_max/2)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	DEBUG_ECHO PREFIX="VAOC_START" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, zcontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_x_offset VALUE={svv.idex_xoffset|default(0.0)|float}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_y_offset VALUE={svv.idex_yoffset|default(0.0)|float}
	
	
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_SAFE_Z_HEIGHT
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_speed VALUE={printer["gcode_macro RatOS"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_accel VALUE={printer["gcode_macro RatOS"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_zhop VALUE={printer["gcode_macro RatOS"].toolchange_zhop|float}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE=0
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"START X_REFERENCE:%.6f Y_REFERENCE:%.6f Z_REFERENCE:%.6f PARK_T0:%.6f PARK_T1:%.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, parking_position_t0, parking_position_t1)}
	
	
	_LED_VAOC_ON
	
	
	
	
	
	
	
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=gcode_z_offset VALUE={printer.gcode_move.homing_origin.z}
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z=0
	
	
	MAYBE_HOME
	M400
	
	
	_LOAD_RATOS_SKEW_PROFILE
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	IDEX_SINGLE
	{% endif %}
	
	
	
	SAVE_GCODE_STATE NAME=vaoc_state
	
	
	RESET_NAMED_OFFSET EVENT=reset_all
	
	
	{% if is_fixed %}
	_SELECT_TOOL T=0 TOOLSHIFT=false
	{% if default_toolhead == 0 %}
	G1 X{idex_xcontrolpoint} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint + safe_distance + additional_safe_distance} F{speed}
	{% else %}
	G1 X{idex_xcontrolpoint - safe_distance - additional_safe_distance} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint} F{speed}
	{% endif %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	{% else %}
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	G1 X{idex_xcontrolpoint} F{speed}
	G1 Y{idex_ycontrolpoint} F{speed}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	
	
	_SELECT_TOOL T={default_toolhead} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	{% if not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={default_toolhead}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=True

[gcode_macro _VAOC_END]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_y = printable_y_max / 2 %}
	{% set saved_gcode_z_offset = printer["gcode_macro _VAOC"].gcode_z_offset|default(0.0)|float %}
	
	DEBUG_ECHO PREFIX="_VAOC_END" MSG="printable_y_max: {printable_y_max}, center_y: {center_y}, safe_z: {safe_z}"
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% set x_offset_change = svv.idex_xoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_x_offset|default(0.0)|float %}
	{% set y_offset_change = svv.idex_yoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_y_offset|default(0.0)|float %}
	{% set offset_change_norm = (x_offset_change ** 2 + y_offset_change ** 2) ** 0.5 %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="VAOC calibration changed the relative XY offset between T0 and T1 by {offset_change_norm|round(3)} mm (ΔX: {x_offset_change|round(3)}, ΔY: {y_offset_change|round(3)})"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	G1 Y{center_y} F{speed}
	
	
	_IDEX_SINGLE INIT=1
	
	
	_LED_VAOC_OFF
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={printer["gcode_macro _VAOC"].cache_toolchange_zhop|float}
	
	
	{% if printer["gcode_macro _VAOC"].is_started_at_temp|default(true)|lower == 'true' %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_bowden_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_bowden_sensor_enabled|int}
	{% endif %}
	{% endif %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro _VAOC"].loaded_skew_profile|default("") %}
	{% if loaded_skew_profile != "" %}
	SKEW_PROFILE LOAD={loaded_skew_profile}
	{% else %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=vaoc_state
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z={saved_gcode_z_offset}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False

[gcode_macro _VAOC_LOAD_TOOL]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set auto_temp_offset = true if params.AUTO_TEMP_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set toolhead_zoffset = svv.idex_zoffset|default(0)|float %}
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move T%s to control point: X%.6f Y%.6f Z%.6f IS_FIXED=%s"' % (t, idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, is_fixed)}
	
	
	{% if not auto_temp_offset and not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={t}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	{% set current_z = printer.toolhead.position.z|float %}
	{% set lowest_toolhead_z = [current_z, current_z - toolhead_zoffset]|min %}
	{% if lowest_toolhead_z < safe_z %}
	G1 Z{[safe_z, safe_z + toolhead_zoffset]|max} F{z_speed}
	{% else %}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	{% endif %}
	
	
	_SELECT_TOOL T={t} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_SET_CAMERA_COOLING]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	
	
	{% set enable_camera_cooling = true if printer["gcode_macro _VAOC"].enable_camera_cooling|default(true)|lower == 'true' else false %}
	{% set camera_cooling_temperature = printer["gcode_macro _VAOC"].camera_cooling_temperature|float %}
	{% set camera_cooling_fan_speed = printer["gcode_macro _VAOC"].camera_cooling_fan_speed|float %}
	
	
	{% if printer.heater_bed.temperature >= camera_cooling_temperature and enable_camera_cooling %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={camera_cooling_fan_speed if t == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={camera_cooling_fan_speed if t == 1 else 0}
	
	
	M106.1 S{camera_cooling_fan_speed}
	
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	{% endif %}

[gcode_macro _VAOC_SET_TOOL]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="_VAOC_SET_TOOL" MSG="IDEX_MODE: {idex_mode}, TOOLHEAD: {toolhead}"
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	{% set x = printer.gcode_move.gcode_position.x|float %}
	{% set y = printer.gcode_move.gcode_position.y|float %}
	{% set z = printer.gcode_move.gcode_position.z|float %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE={x}
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE={y}
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE={z}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Control point was set: X%.6f Y%.6f Z%.6f"' % (x, y, z)}
	
	{% else %}
	
	
	
	{% set move_diff_x = printer.gcode_move.gcode_position.x|float - svv.idex_xcontrolpoint|float %}
	{% set move_diff_y = printer.gcode_move.gcode_position.y|float - svv.idex_ycontrolpoint|float %}
	{% set move_diff_z = printer.gcode_move.gcode_position.z|float - svv.idex_zcontrolpoint|float %}
	
	
	{% set new_x_offset = svv.idex_xoffset - move_diff_x %}
	{% set new_y_offset = svv.idex_yoffset - move_diff_y %}
	{% set new_z_offset = svv.idex_zoffset - move_diff_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE={new_x_offset}
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE={new_y_offset}
	
	{% set z_focus_msg = "" %}
	{% if move_diff_z|abs > 1e-6 %}
	{% if printer["gcode_macro _VAOC"].adjusting_secondary_toolhead_focus_adjusts_zoffset|default(false)|lower == 'true' %}
	{% set z_focus_msg = " (Z offset adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={new_z_offset}
	{% else %}
	{% set z_focus_msg = " (Z offset not adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	{% set new_z_offset = svv.idex_zoffset %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset was set: X%.6f Y%.6f Z%.6f%s"' % (toolhead, new_x_offset, new_y_offset, new_z_offset, z_focus_msg)}
	
	{% endif %}

[gcode_macro _VAOC_MOVE]
gcode = 
	
	{% set x = params.X|default(0)|float %}
	{% set y = params.Y|default(0)|float %}
	{% set z = params.Z|default(0)|float %}
	
	
	G91
	{% if z != 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 Z%.6f F300"' % (z)}
	G1 Z{z} F300
	
	{% else %}
	{% if x <=2 and y <=2 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 X%.6f Y%.6f F18000"' % (x, y)}
	G1 X{x} Y{y} F18000
	{% endif %}
	{% endif %}
	G90

[gcode_macro _VAOC_CALIBRATE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	{% if printer["z_offset_probe"] is defined and is_started %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	
	{% if auto_z_offset %}
	_START_VAOC AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_END
	{% else %}
	_VAOC_LOAD_TOOL T={default_toolhead}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	{% endif %}
	
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_Z_OFFSET
	
	{% endif %}

[gcode_macro _VAOC_PROBE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}
	{% if not auto_z_offset %}
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	{% endif %}
	M400
	_VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT

[gcode_macro _VAOC_Z_OFFSET_PROBE_CURRENT_POSITION]
gcode = 
	
	Z_OFFSET_PROBE PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_DROP=1 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median

[gcode_macro _VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT]
gcode = 
	{% if printer["z_offset_probe"] is defined %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE={last_z}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Z-offset control point set:: %.6f"' % last_z}
	
	{% else %}
	
	
	
	{% set z = svv.idex_zoffsetcontrolpoint|float - last_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={z}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-z)}
	
	
	G0 Z{svv.idex_zcontrolpoint|float} F{z_speed}
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset set: Z %.6f"' % (t, z)}
	
	{% endif %}
	
	{% endif %}

[gcode_macro _VAOC_ECHO_Z_OFFSET]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s toolhead z-offset %.6f"' % (1 if default_toolhead == 0 else 0, svv.idex_zoffset)}
	{% if svv.idex_zoffset|abs < 0.02 %}
	CONSOLE_ECHO TITLE={'"Perfect toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="You have a perfect toolhead z-offset!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.02 and svv.idex_zoffset|abs < 0.05 %}
	CONSOLE_ECHO TITLE={'"Good toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is good!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.05 and svv.idex_zoffset|abs < 0.1 %}
	CONSOLE_ECHO TITLE={'"High toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset could be better._N_Use minimum 0.3mm first layer height for copy and mirror mode prints." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.1 and svv.idex_zoffset|abs < 0.2 %}
	CONSOLE_ECHO TITLE={'"Bad toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is bad._N_Copy and mirror mode prints are not recommended with it." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.2 %}
	CONSOLE_ECHO TITLE={'"Unacceptable toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is unacceptable._N_Do not print in copy and mirror mode with it." TYPE="alert"
	{% endif %}
	RATOS_ECHO PREFIX="VAOC" MSG="Toolhead z-offset calibration done!"

[gcode_macro _VAOC_CALIBRATE_TEMP_OFFSET]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if is_fixed and is_started and printer["z_offset_probe"] is defined and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	_VAOC_LOAD_TOOL T={default_toolhead} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_NOZZLE_TEMP_OFFSETS
	
	{% endif %}

[gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET=0
	
	
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	M400

[gcode_macro _VAOC_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(150)|float %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Probing with nozzle temperature {temp}°C..."
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	
	
	G0 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _VAOC_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set msg = '"T0 expansion coefficient %.6fmm_N_T1 expansion coefficient %.6fmm"' % (svv.nozzle_expansion_coefficient_t0, svv.nozzle_expansion_coefficient_t1) %}
	CONSOLE_ECHO TITLE="Nozzle expansion coefficients:" MSG={msg} TYPE="success"

[gcode_macro _VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - expected_camera_x_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC x-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_xcontrolpoint, expected_camera_x_position)) }
	{% endif %}
	{% if (idex_ycontrolpoint - expected_camera_y_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC y-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_ycontrolpoint, expected_camera_y_position)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - printer.gcode_move.gcode_position.x|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected y-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_xcontrolpoint, printer.gcode_move.gcode_position.x|float)) }
	{% endif %}
	{% if (idex_ycontrolpoint - printer.gcode_move.gcode_position.y|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected x-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_ycontrolpoint, printer.gcode_move.gcode_position.y|float)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_SAFE_Z_HEIGHT]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set idex_zoffsetcontrolpoint = svv.idex_zoffsetcontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_SAFE_Z_HEIGHT" MSG={'"idex_zcontrolpoint: %.6f, idex_zoffsetcontrolpoint: %.6f"' % (idex_zcontrolpoint, idex_zoffsetcontrolpoint)}
	
	{% if safe_z < idex_zcontrolpoint + 2 or safe_z < idex_zoffsetcontrolpoint + 2 %}
	{action_raise_error("VAOC safe_z value (%.3f) is too low, it must be higher than %.3f" % (safe_z, [idex_zoffsetcontrolpoint + 2, idex_zcontrolpoint + 2]|max))}
	{% endif %}

[gcode_macro _VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED]
gcode = 
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T0. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T1. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_RESET]
gcode = 
	DEBUG_ECHO PREFIX="_VAOC_RESET" MSG="running template-emitted _VAOC_RESET macro"
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE=212.5
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE=530.5
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE=10
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE=0
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE=0.0
	
	RESET_DC_ENDSTOP_CONFIGURATION
	RESET_Y_MAX_ADJUSTMENT
	
	
	CONSOLE_ECHO TITLE="VAOC Configuration Reset" MSG="VAOC configuration has been reset. You must RESTART klipper for the changes to take effect,_N_then re-calibrate VAOC."

[gcode_macro _ECHO_VAOC_VARS]
description = Echo VAOC variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro _VAOC"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro _VAOC_SWITCH_LED]
gcode = 
	{% if params.STATE|default(0)|int == 1 %}
	_LED_VAOC_ON
	{% else %}
	_LED_VAOC_OFF
	{% endif %}

[gcode_macro Z_PROBE_TEST_T0]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T0
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST_T1]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T1
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	
	
	_VAOC_Z_PROBE_TEST_EVALUATE
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro _VAOC_Z_PROBE_LOOP]
gcode = 
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_SHAKE_IT
	_VAOC_START

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if primary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T0. Retried {primary_retries} time(s)."
	{% endif %}
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	
	{% if (primary_range - secondary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 is drifting significantly more than T1."
	{% endif %}
	{% if (secondary_range - primary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 is drifting significantly more than T0."
	{% endif %}
	
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T0]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T1]
gcode = 
	
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _SHAKE_IT]
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	_Z_HOP
	{% for i in range(3) %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 + 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 + 1}
	{% endfor %}
	{% for i in range(2) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 + 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 + 50}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 1}
	{% endfor %}
	{% endfor %}

[gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 retries updated: {new_retries}"

[gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 retries updated: {new_retries}"

[gcode_macro _CLEAR_PRIMARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _CLEAR_SECONDARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _VAOC_TEST_Z_OFFSET]
gcode = 
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}

[delayed_gcode _IDEX_INIT]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	VERIFY_HYBRID_INVERTED

[gcode_macro Z_TILT_ADJUST]
rename_existing = Z_TILT_ADJUST_ORIG
gcode = 
	
	{% set beacon_contact_z_tilt_adjust_samples = printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust_samples|default(2)|int %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(true)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	_IDEX_SINGLE
	
	_SELECT_TOOL T={printer["gcode_macro RatOS"].default_toolhead|default(0)|int} TOOLSHIFT=false
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_tilt_adjust %}
	Z_TILT_ADJUST_ORIG PROBE_METHOD=contact SAMPLES={beacon_contact_z_tilt_adjust_samples}
	{% else %}
	Z_TILT_ADJUST_ORIG
	{% endif %}
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if idex_mode == "copy" %}
	_IDEX_COPY
	{% elif idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[stepper_x]
position_max = 500
position_endstop = -59.6
position_min = -59.6
step_pin = PF13
dir_pin = x_dir_pin
enable_pin = !PF14
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t0:PA2

[stepper_y]
position_max = 533.65
position_min = -14.35
position_endstop = -14.35
step_pin = PG0
dir_pin = !y_dir_pin
enable_pin = !PF15
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = PG9

[stepper_z]
position_max = 500
position_min = -7
step_pin = PC13
dir_pin = !z0_dir_pin
enable_pin = !PF1
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4
homing_speed = 10
endstop_pin = probe:z_virtual_endstop

[z_tilt]
z_positions = 
	0,0
	250,500
	500,0
points = 
	20, 10
	480, 230
	20, 450
horizontal_move_z = 20
retries = 10
retry_tolerance = 0.02
speed = 600

[extruder]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t0:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t0:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t0:PD3
dir_pin = toolboard_t0:e_dir_pin
enable_pin = !toolboard_t0:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[firmware_retraction]
retract_speed = 60
unretract_extra_length = 0
unretract_speed = 60
retract_length = 0.2

[extruder1]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t1:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t1:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t1:PD3
dir_pin = toolboard_t1:e_dir_pin
enable_pin = !toolboard_t1:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[resonance_tester]
accel_chip_x = lis2dw toolboard_t0
accel_chip_y = lis2dw toolboard_t0
probe_points = 
	250,250,20

[tmc5160 stepper_x]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC4
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 dual_carriage]
stealthchop_threshold = 0
interpolate = True
cs_pin = PF2
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y]
stealthchop_threshold = 0
interpolate = True
cs_pin = PD11
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y1]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC7
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[stepper_y1]
step_pin = PG4
dir_pin = y1_dir_pin
enable_pin = !PA2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46

[tmc2209 stepper_z]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE4
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[tmc2209 stepper_z1]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE1
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z1]
step_pin = PE2
dir_pin = !z1_dir_pin
enable_pin = !PD4
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 stepper_z2]
stealthchop_threshold = 0
interpolate = True
uart_pin = PD3
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z2]
step_pin = PE6
dir_pin = !z2_dir_pin
enable_pin = !PE0
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 extruder]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t0:PB3
run_current = 0.707
sense_resistor = 0.11

[tmc2209 extruder1]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t1:PB3
run_current = 0.707
sense_resistor = 0.11

[beacon]
serial = /dev/beacon
x_offset = 0
y_offset = 27.5
mesh_main_direction = x
mesh_runs = 1
mesh_cluster_size = 0
speed = 15.
lift_speed = 80.
contact_max_hotend_temperature = 275
contact_mesh_min = 20,20
contact_mesh_max = 480,480

[beacon_user_z_offset]

[beacon_mesh]

[beacon_true_zero_correction]

[beacon_adaptive_heat_soak]

[delayed_gcode _BEACON_INIT]
initial_duration = 1
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	_BEACON_MESH_INIT
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_coefficient_multiplier
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_applied_offset
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=beacon_saved_runtime_offset
	{% if printer["gcode_macro RatOS"].beacon_contact_expansion_multiplier is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_contact_expansion_multiplier is no longer used, please remove it from your config file."
	{% endif %}
	{% if printer["gcode_macro RatOS"].beacon_scan_compensation_resolution is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_scan_compensation_resolution is no longer used, please remove it from your config file."
	{% endif %}

[gcode_macro BEACON_RATOS_CALIBRATION]
gcode = 
	RATOS_ECHO MSG="Did you mean BEACON_RATOS_CALIBRATE?"

[gcode_macro BEACON_RATOS_CALIBRATE]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	BEACON_INITIAL_CALIBRATION _AUTOMATED=True
	
	{% if beacon_contact_start_print_true_zero %}
	BEACON_POKE_TEST _AUTOMATED=True
	_BEACON_CHECK_POKE
	{% if printer["dual_carriage"] is not defined %}
	BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET _AUTOMATED=True
	{% endif %}
	{% endif %}
	
	{% set already_heated = False %}
	
	
	{% if beacon_contact_start_print_true_zero and beacon_scan_compensation_enable %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% set already_heated = True %}
	{% endif %}
	
	
	BEACON_FINAL_CALIBRATION _AUTOMATED=True _AUTOMATED_ALREADY_HEATED={already_heated} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	{% if beacon_contact_start_print_true_zero %}
	{% if printer["dual_carriage"] is not defined %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	_BEACON_ECHO_POKE
	{% endif %}
	RATOS_ECHO MSG="Beacon calibration finished!"
	
	
	_LED_BEACON_CALIBRATION_END
	
	
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG

[gcode_macro BEACON_INITIAL_CALIBRATION]
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Initial beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro BEACON_FINAL_CALIBRATION]
description = Runs BEACON_AUTO_CALIBRATE after heating the bed and chamber to specified temperatures. This creates a beacon model under reference conditions for future use.
	This macro will skip calibration if both the beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero settings are enabled, because a new
	model will be calibrated automatically at the start of each print. Use FORCE=True to override this check.
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set already_heated = true if params._AUTOMATED_ALREADY_HEATED|default(false)|lower == 'true' else false %}
	{% set force = params.FORCE|default('false')|lower in ('1', 'true', 'yes') %}
	
	
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default('false')|lower == "true" %}
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero and not force %}
	RATOS_ECHO MSG="BEACON_FINAL_CALIBRATION skipped, not needed because beacon_contact_calibrate_model_on_true_zero is enabled. Use FORCE=True to override."
	{% else %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	{% if chamber_temp > 0 and not already_heated %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	{% if not already_heated %}
	
	G0 Z2.5 F{z_hop_speed}
	
	
	RATOS_ECHO MSG="Waiting for calibration temperature..."
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	{% if beacon_adaptive_heat_soak %}
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,3600]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_Z_HOP
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Final beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	{% endif %}

[gcode_macro BEACON_POKE_TEST]
variable_poke_result_1 = -1
variable_poke_result_2 = -1
variable_poke_result_3 = -1
variable_poke_result_4 = -1
variable_poke_result_5 = -1
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_1 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_2 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_3 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_4 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_5 VALUE=-1
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G0 Z5 F{z_hop_speed}
	
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=1
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=2
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=3
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=4
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=5
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Beacon poke test finished!"
	{% if not automated %}
	_BEACON_ECHO_POKE
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro _BEACON_PROBE_POKE]
gcode = 
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	BEACON_POKE speed=3 top=5 bottom={poke_bottom}
	BEACON_QUERY

[gcode_macro _BEACON_STORE_POKE]
gcode = 
	
	{% set i = params.I|default(1)|int %}
	
	
	{% set last_z = printer.beacon.last_poke_result|default(0)|float %}
	
	
	{% if printer.beacon.last_poke_result|lower != "none" %}
	{% if printer.beacon.last_poke_result.error == 0 %}
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE={"poke_result_%s" % i} VALUE={printer.beacon.last_poke_result.latency}
	{% endif %}
	{% endif %}

[gcode_macro _BEACON_CHECK_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% if p1 == -1 or p2 == -1 or p3 == -1 or p4 == -1 or p5 == -1 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test error!") }
	{% endif %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	{% if avg > 6 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test failed!") }
	{% endif %}

[gcode_macro _BEACON_ECHO_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	
	
	{% if avg <= 1 %}
	{% set type = "success" %}
	{% set note = "Extremely low noise, rarely achieved" %}
	{% elif avg > 1 and avg <= 4 %}
	{% set type = "info" %}
	{% set note = "Excellent performance for a typical printer" %}
	{% elif avg > 4 and avg <= 8 %}
	{% set type = "warning" %}
	{% set note = "Acceptable performance, machine may have considerable cyclic axis noise" %}
	{% elif avg > 8 and avg <= 11 %}
	{% set type = "alert" %}
	{% set note = "Not ideal, may want to verify proper mounting or use thinner stackups" %}
	{% elif avg > 11 %}
	{% set type = "alert" %}
	{% set note = "Reason for concern, present setup may be risky to continue with" %}
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon poke test result:" TYPE={type} MSG={'"Average latency: %.2f_N_%s"' % (avg, note)}

[gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Nozzle temperature offset calibration..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET=0
	
	
	{% if not automated %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing with nozzle temperature {temp}°C..."
	PROBE PROBE_METHOD=contact PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median
	BEACON_QUERY
	
	
	G0 Z5 F{z_speed}

[gcode_macro _BEACON_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer.beacon.last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{default_toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% if default_toolhead == 0 %}
	CONSOLE_ECHO TYPE="info" MSG={'"T0 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t0}
	{% else %}
	CONSOLE_ECHO TYPE="info" MSG={'"T1 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t1}
	{% endif %}

[gcode_macro _BEACON_SET_NOZZLE_TEMP_OFFSET]
description = "Set the thermal expansion z offset for the active toolhead based on the current extruder target temperature and thermal expansion coefficient."
gcode = 
	{% if params.RESET is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The RESET parameter is no longer supported and has no effect."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% if params.TOOLHEAD is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The TOOLHEAD parameter is no longer supported and has no effect. The macro now automatically determines the current toolhead."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	{% if beacon_contact_expansion_compensation %}
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set nozzle_expansion_coefficient_t0 = svv.nozzle_expansion_coefficient_t0|default(0)|float %}
	{% if printer["dual_carriage"] is defined %}
	{% set nozzle_expansion_coefficient_t1 = svv.nozzle_expansion_coefficient_t1|default(0)|float %}
	{% endif %}
	
	
	{% set temp = printer['extruder' if toolhead == 0 else 'extruder1'].target|float %}
	
	
	{% set temp_delta = temp - beacon_contact_true_zero_temp %}
	{% set expansion_coefficient = nozzle_expansion_coefficient_t0 if toolhead == 0 else nozzle_expansion_coefficient_t1 %}
	{% set expansion_offset = temp_delta * (expansion_coefficient / 100) %}
	
	
	SET_NAMED_OFFSET NAME=hotend_thermal_expansion Z={expansion_offset} MOVE=1 MOVE_SPEED={z_speed}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG={'"Nozzle expansion offset of %.6fmm applied to T%s"' % (expansion_offset, toolhead)}
	DEBUG_ECHO PREFIX="_BEACON_SET_NOZZLE_TEMP_OFFSET" MSG="toolhead: {toolhead}, coefficient: {expansion_coefficient|round(6)}, temp_delta: {temp_delta|round(1)},  expansion_offset: {expansion_offset|round(6)}"
	
	{% endif %}

[gcode_macro BEACON_MEASURE_BEACON_OFFSET]
variable_needs_compensation = False
variable_reference_z = 0.0
variable_front = 0.0
variable_front_left = 0.0
variable_front_right = 0.0
variable_back = 0.0
variable_back_left = 0.0
variable_back_right = 0.0
variable_right = 0.0
variable_left = 0.0
variable_margin_x = 40
variable_margin_y = 40
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=False
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Measure beacon offset..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="center"
	
	
	G0 X{margin_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_left"
	
	
	G0 X{safe_home_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front"
	
	
	G0 X{(printable_x_max - margin_x)} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_right"
	
	
	G0 X{safe_home_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back"
	
	
	G0 X{margin_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_left"
	
	
	G0 X{margin_x} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="left"
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_BEACON_ECHO_BEACON_OFFSET
	
	
	_LED_BEACON_CALIBRATION_END
	
	{% endif %}

[gcode_macro _BEACON_STORE_BEACON_OFFSET]
gcode = 
	
	{% set location = params.LOCATION|lower %}
	
	
	{% set last_z = printer.beacon.last_offset_result["delta"]|default(0)|float %}
	
	
	{% if location == "center" %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE={location} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_BEACON_OFFSET]
gcode = 
	
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float * 1000 %}
	{% set front_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_left|default(0)|float * 1000 %}
	{% set front = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front|default(0)|float * 1000 %}
	{% set front_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_right|default(0)|float * 1000 %}
	{% set right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].right|default(0)|float * 1000 %}
	{% set back_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_right|default(0)|float * 1000 %}
	{% set back = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back|default(0)|float * 1000 %}
	{% set back_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_left|default(0)|float * 1000 %}
	{% set left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].left|default(0)|float * 1000 %}
	
	{% set line_1 = "Front left:    %.6fμm" % (front_left) %}
	{% set line_2 = "Front center:  %.6fμm" % (front) %}
	{% set line_3 = "Front right:   %.6fμm" % (front_right) %}
	{% set line_4 = "Left center:   %.6fμm" % (left) %}
	{% set line_5 = "Right center:  %.6fμm" % (right) %}
	{% set line_6 = "Back left:     %.6fμm" % (back_left) %}
	{% set line_7 = "Back center:   %.6fμm" % (back) %}
	{% set line_8 = "Back right:    %.6fμm" % (back_right) %}
	
	{% set max_value = [(front_left|abs), (front|abs), (front_right|abs), (left|abs), (right|abs), (back_left|abs), (back|abs), (back_right|abs)]|max %}
	{% if max_value <= 50 %}
	{% set type = "success" %}
	{% set recommendation = "Very low beacon offset: %.6fμm._N_No beacon scan compensation needed." % max_value %}
	{% elif max_value > 50 and max_value <= 100 %}
	{% set type = "info" %}
	{% set recommendation = "Low beacon offset: %.6fμm._N_You may experience first layer inconsistensies, consider beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 100 and max_value <= 150 %}
	{% set type = "warning" %}
	{% set recommendation = "High beacon offset: %.6fμm._N_High chance of first layer problems, beacon scan compensation is highly encouraged." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 150 and max_value <= 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Very High beacon offset: %.6fμm._N_You will encounter first layer problems on large prints unless you activate beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Extremely high beacon offset: %.6fμm._N_You have significant scan/contact inconsistency which is indicative of mechanical problems, please investigate before resorting to software compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon offset relative to the center" TYPE={type} MSG={'"_N_%s_N__N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s"' % (recommendation, line_1, line_2, line_3, line_4, line_5, line_6, line_7, line_8)}

[gcode_macro BEACON_CREATE_SCAN_COMPENSATION_MESH]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set profile = params.PROFILE|default("auto")|string %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set keep_temp_meshes = params.KEEP_TEMP_MESHES|default(0) %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' %}
	{% set desired_spacing = printer["gcode_macro RatOS"].beacon_scan_compensation_desired_spacing|float %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	
	{% if not beacon_scan_compensation_enable %}
	RATOS_ECHO MSG="Beacon scan compensation is disabled!"
	
	{% else %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	
	
	RATOS_ECHO MSG="Please wait..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	G1 Z2.5 F{z_speed}
	{% if beacon_adaptive_heat_soak %}
	
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,9000]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if not (beacon_adaptive_heat_soak or bed_heat_soak_time > 0) %}
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if printer.z_tilt is defined %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% endif %}
	{% if printer.quad_gantry_level is defined %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% endif %}
	
	
	_BEACON_CREATE_SCAN_COMPENSATION_MESH_CORE PROFILE="{profile}" DESIRED_SPACING={desired_spacing} CHAMBER_TEMP={chamber_temp} KEEP_TEMP_MESHES={keep_temp_meshes}
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	{% if automated %}
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon scan compensation mesh created!"
	
	
	{% if not automated %}
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED]
gcode = 
	
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED" MSG="beacon_scan_compensation_profile {beacon_scan_compensation_profile}, beacon_scan_compensation_enable {beacon_scan_compensation_enable}"
	
	{% if beacon_scan_compensation_enable %}
	BEACON_APPLY_SCAN_COMPENSATION PROFILE="{beacon_scan_compensation_profile}"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL]
gcode = 
	
	{% set beacon_contact_start_print_true_zero = params.BEACON_CONTACT_START_PRINT_TRUE_ZERO|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = params.beacon_contact_calibrate_model_on_true_zero|lower == 'true' %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and not printer.beacon.model %}
	{% set beacon_model_required_for_true_zero = beacon_contact_start_print_true_zero and not beacon_contact_calibrate_model_on_true_zero %}
	{% set beacon_model_required_for_homing =
	printer.fastconfig.settings.stepper_z.endstop_pin == 'probe:z_virtual_endstop'
	and (( printer.fastconfig.settings.beacon.home_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower != 'true')
	or ( printer.fastconfig.settings.beacon.default_probe_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower != 'true' )) %}
	{% if beacon_model_required_for_homing or beacon_model_required_for_true_zero %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("An active Beacon model is required. Have you performed initial Beacon calibration?") }
	{% endif %}
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION]
gcode = 
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set bed_temp_mismatch_is_error = true if printer["gcode_macro RatOS"].beacon_scan_compensation_bed_temp_mismatch_is_error|default(false)|lower == 'true' else false %}
	
	{% set bed_temp = params.BED_TEMP|default(0)|float %}
	{% if bed_temp == 0 %}
	{% set bed_temp = printer.heater_bed.temperature %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_PREFLIGHT_CHECK_BEACON" MSG="beacon_scan_compensation_profile={beacon_scan_compensation_profile}, beacon_scan_compensation_enable={beacon_scan_compensation_enable}, bed_temp={bed_temp}"
	
	{% if beacon_scan_compensation_enable %}
	_VALIDATE_COMPENSATION_MESH_PROFILE PROFILE="{beacon_scan_compensation_profile}" TITLE="Check Beacon scan compensation profile" SUBJECT="Configured compensation profile '{beacon_scan_compensation_profile}'" COMPARE_BED_TEMP={bed_temp} COMPARE_BED_TEMP_IS_ERROR={bed_temp_mismatch_is_error}
	{% endif %}

[gcode_macro _BEACON_MAYBE_SCAN_COMPENSATION]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set needs_scan_compensation = true if printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].needs_compensation|default(false)|lower == 'true' else false %}
	
	{% if needs_scan_compensation %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% endif %}

[gcode_macro _BEACON_HOME_AND_ABL]
gcode = 
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	{% if needs_rehoming %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}

[gcode_macro SAVE_Z_OFFSET]
description = Deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead, or in Mainsail use the SAVE button in the Z-OFFSET section.
gcode = 
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default('false')|lower == 'true' %}
	{% set msg = "SAVE_Z_OFFSET is deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead,_N_or in Mainsail use the SAVE button in the Z-OFFSET section."%}
	{% if not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% set msg = msg + "_N_You must then use the SAVE_CONFIG command to persist the change." %}
	{% endif %}
	CONSOLE_ECHO TYPE="error" MSG="{msg}"

[gcode_macro _BEACON_OFFSET_COMPARE]
gcode = 
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing..."
	
	
	BEACON_OFFSET_COMPARE SAMPLES_DROP=1 SAMPLES=3
	BEACON_QUERY

[fan]
pin = rpi:gpio4

[fan_generic part_fan_t0]
pin = PA8
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[fan_generic part_fan_t1]
pin = PE5
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[heater_fan toolhead_cooling_fan_t0]
heater = extruder
shutdown_speed = 1
pin = toolboard_t0:PB4

[heater_fan toolhead_cooling_fan_t1]
heater = extruder1
shutdown_speed = 1
pin = toolboard_t1:PB4

[controller_fan controller_fan]
pin = dinghy:PA4
tachometer_pin = dinghy:PC15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[z_offset_probe]
pin = ^PG10
z_offset = -7
y_offset = 0
x_offset = 37.5
speed = 10
samples = 3
sample_retract_dist = 5
lift_speed = 10.0
samples_result = median
samples_tolerance = 0.2
samples_tolerance_retries = 5

[neopixel vaoc_led]
pin = PB10
chain_count = 6
color_order = GRB

[heater_fan vaoc_fan]
pin = PD13
heater = heater_bed
fan_speed = 1.0
heater_temp = 50

[fan_generic filter]
pin = !PD14
enable_pin = PD15

[gcode_macro T0]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = True
variable_color = "7bff33"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = -32.6
variable_parking_position = -57.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=0 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[gcode_macro T1]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = False
variable_color = "0ea5e9"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = 532.6
variable_parking_position = 557.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=1 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[save_variables]
filename = /home/pi/printer_data/config/ratos-variables.cfg

[mcu dinghy]
serial = /dev/serial/by-id/usb-Klipper_stm32f072xb_Dragon_dinghy-if00

[temperature_sensor th0]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA0

[temperature_sensor th1]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA1

[temperature_sensor th2]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA2

[temperature_sensor th3]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA3

[controller_fan CTL2]
pin = dinghy:PB14
tachometer_pin = dinghy:PB15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[mcu plasma]
serial = /dev/serial/by-id/usb-Klipper_rp2040_Plasma-if00

[neopixel Chamber_Lights]
pin = plasma:gpio15
chain_count = 140
color_order = GRBW
initial_red = 0.0
initial_green = 0.0
initial_blue = 0.0
initial_white = 0.1

[beacon model default]
model_coef = 1.5287863993594841,
	1.9289099639750602,
	0.8838828622507556,
	0.25554883784260735,
	-0.015171504024913506,
	0.3044946127013882,
	0.15820427856566457,
	-0.25262403959326246,
	0.042488512846660914,
	0.16662470122520964
model_domain = 1.842634574664148e-07,1.9339206373083917e-07
model_range = 0.200000,5.000000
model_temp = 13.222247
model_offset = 0.00000

[bed_mesh default]
version = 1
points = 
	0.016163, 0.016713, 0.001923, -0.017658, -0.031574, -0.032498, -0.030898, -0.032177, -0.035213, -0.031148, -0.021322, -0.016924, -0.015012, -0.013911, -0.012197, -0.012583, -0.010489, -0.007529, -0.003986, -0.000980, 0.005518, 0.014442, 0.027426, 0.034677, 0.037410, 0.040391, 0.041842, 0.040369, 0.037615, 0.030776, 0.027664, 0.022856, 0.016892, 0.015398, 0.014717, 0.006921, 0.001532, 0.000731, 0.008657, 0.014036
	0.005356, -0.005066, -0.016998, -0.029668, -0.038334, -0.043672, -0.041139, -0.042488, -0.045199, -0.039432, -0.028746, -0.023642, -0.024058, -0.022802, -0.019679, -0.018514, -0.018102, -0.016476, -0.012722, -0.010077, -0.001809, 0.007180, 0.019853, 0.027754, 0.029964, 0.033626, 0.036783, 0.032018, 0.029372, 0.020847, 0.017634, 0.011926, 0.009013, 0.009254, 0.007972, -0.001380, -0.006940, -0.002160, 0.006135, 0.008330
	-0.004900, -0.006720, -0.021914, -0.039691, -0.050459, -0.050377, -0.046281, -0.048755, -0.054708, -0.051499, -0.033927, -0.027632, -0.030243, -0.031447, -0.024387, -0.021408, -0.020382, -0.018068, -0.015930, -0.013877, -0.006099, 0.003479, 0.013310, 0.024783, 0.025522, 0.030849, 0.033573, 0.031409, 0.025495, 0.016683, 0.011264, 0.008805, 0.006856, 0.008059, 0.007305, 0.002581, -0.003320, -0.003239, 0.004691, 0.010045
	-0.008791, -0.019334, -0.029149, -0.040533, -0.051698, -0.058235, -0.054863, -0.054840, -0.055692, -0.049534, -0.036731, -0.033053, -0.035667, -0.035315, -0.024352, -0.023825, -0.022538, -0.020438, -0.018207, -0.015389, -0.006515, 0.001966, 0.013591, 0.019434, 0.020600, 0.024967, 0.029425, 0.026812, 0.018980, 0.007878, 0.002360, 0.000859, 0.003849, 0.005649, 0.005421, -0.000416, -0.007906, -0.003164, 0.007582, 0.010039
	-0.018512, -0.018210, -0.033932, -0.050501, -0.061588, -0.064139, -0.060236, -0.062528, -0.067065, -0.062039, -0.045815, -0.039448, -0.040521, -0.042080, -0.033870, -0.030878, -0.027396, -0.024548, -0.021298, -0.020041, -0.011880, -0.002847, 0.008689, 0.015857, 0.015934, 0.018697, 0.022439, 0.022106, 0.017916, 0.005879, 0.001037, -0.001311, -0.001335, 0.001897, 0.003656, 0.000561, -0.006084, -0.005683, 0.000338, 0.006245
	-0.028558, -0.036721, -0.044680, -0.054969, -0.066140, -0.075045, -0.073515, -0.073161, -0.075696, -0.068963, -0.058892, -0.053111, -0.050990, -0.048040, -0.041262, -0.037419, -0.034866, -0.031845, -0.029787, -0.026524, -0.017896, -0.009322, -0.001010, 0.005819, 0.008058, 0.010456, 0.013266, 0.012529, 0.007992, -0.001491, -0.006769, -0.009303, -0.005980, -0.003567, -0.003340, -0.011496, -0.018818, -0.014808, -0.004181, -0.000733
	-0.037253, -0.038393, -0.053129, -0.066170, -0.075959, -0.079233, -0.077475, -0.082688, -0.086779, -0.083983, -0.069005, -0.062542, -0.060351, -0.058481, -0.051101, -0.043149, -0.039837, -0.037039, -0.034698, -0.031301, -0.024330, -0.019786, -0.010285, -0.001967, 0.002812, 0.004899, 0.009657, 0.006946, 0.002155, -0.005232, -0.009851, -0.011218, -0.011509, -0.010097, -0.010293, -0.013175, -0.018958, -0.019846, -0.012107, -0.005641
	-0.046584, -0.055590, -0.062606, -0.069218, -0.080399, -0.087414, -0.089037, -0.092376, -0.095115, -0.088957, -0.080802, -0.073290, -0.068741, -0.064591, -0.054452, -0.048270, -0.045916, -0.044559, -0.042047, -0.039605, -0.032667, -0.025789, -0.019495, -0.012773, -0.006697, -0.003025, 0.001413, 0.000817, -0.004738, -0.013008, -0.017605, -0.018191, -0.018524, -0.016356, -0.016750, -0.021992, -0.028943, -0.025791, -0.016146, -0.010447
	-0.051029, -0.051677, -0.068218, -0.079622, -0.088590, -0.089331, -0.089731, -0.096072, -0.105329, -0.100771, -0.087584, -0.079320, -0.075489, -0.072081, -0.064183, -0.054662, -0.048601, -0.049465, -0.047050, -0.045011, -0.040009, -0.032508, -0.025212, -0.018144, -0.011996, -0.008136, -0.003187, -0.003214, -0.006646, -0.013044, -0.019446, -0.020615, -0.022270, -0.021298, -0.020215, -0.020946, -0.026034, -0.026598, -0.021025, -0.012328
	-0.057184, -0.064908, -0.073093, -0.081584, -0.091971, -0.097048, -0.097688, -0.101869, -0.106651, -0.102162, -0.095658, -0.087938, -0.082718, -0.077017, -0.069608, -0.060682, -0.056889, -0.056864, -0.054260, -0.052011, -0.044563, -0.038927, -0.031943, -0.025832, -0.021170, -0.014319, -0.009046, -0.008543, -0.011751, -0.020287, -0.026608, -0.027259, -0.029120, -0.025549, -0.023221, -0.027725, -0.032477, -0.028427, -0.019343, -0.014932
	-0.060411, -0.062241, -0.080781, -0.090744, -0.100903, -0.099702, -0.098468, -0.104236, -0.116853, -0.112701, -0.102623, -0.095036, -0.091407, -0.089871, -0.079701, -0.070222, -0.064325, -0.063875, -0.062248, -0.059396, -0.052699, -0.047589, -0.041526, -0.028442, -0.024526, -0.019549, -0.015403, -0.014251, -0.017989, -0.022824, -0.027328, -0.029155, -0.033315, -0.032426, -0.027619, -0.030776, -0.033688, -0.032458, -0.027219, -0.019649
	-0.067541, -0.076514, -0.082321, -0.088656, -0.099968, -0.104930, -0.105875, -0.109051, -0.115531, -0.112996, -0.105760, -0.100390, -0.096171, -0.090011, -0.080050, -0.073632, -0.067451, -0.067031, -0.065225, -0.062471, -0.056370, -0.050129, -0.041626, -0.030801, -0.027579, -0.022472, -0.014826, -0.015306, -0.020316, -0.025953, -0.030661, -0.034103, -0.035502, -0.032738, -0.031311, -0.037314, -0.041306, -0.035280, -0.027449, -0.020395
	-0.068162, -0.069269, -0.088235, -0.096809, -0.103385, -0.103271, -0.102507, -0.109535, -0.123412, -0.118580, -0.106622, -0.099580, -0.097644, -0.096978, -0.087259, -0.077196, -0.068978, -0.067016, -0.063682, -0.062548, -0.057901, -0.052295, -0.044088, -0.032703, -0.026551, -0.021607, -0.014155, -0.013747, -0.017390, -0.022419, -0.027444, -0.030877, -0.033450, -0.032423, -0.032041, -0.033598, -0.035149, -0.034054, -0.029356, -0.020998
	-0.069473, -0.075924, -0.083569, -0.089648, -0.101235, -0.105828, -0.109144, -0.112613, -0.117233, -0.114186, -0.107090, -0.098616, -0.097084, -0.094257, -0.086773, -0.076409, -0.069532, -0.066472, -0.060956, -0.059191, -0.052886, -0.047752, -0.041275, -0.032437, -0.027780, -0.020398, -0.012061, -0.010133, -0.014056, -0.021528, -0.027924, -0.030605, -0.030609, -0.026068, -0.029346, -0.033991, -0.038254, -0.030610, -0.021109, -0.015885
	-0.068084, -0.066409, -0.083944, -0.094013, -0.102504, -0.105274, -0.106036, -0.112090, -0.121664, -0.117824, -0.104850, -0.097467, -0.098833, -0.098622, -0.089603, -0.078147, -0.068143, -0.066300, -0.061573, -0.057727, -0.054825, -0.048625, -0.040164, -0.030532, -0.025948, -0.020264, -0.014196, -0.010702, -0.013794, -0.019775, -0.026095, -0.028838, -0.030254, -0.027944, -0.027980, -0.030915, -0.032446, -0.028861, -0.023732, -0.014676
	-0.065280, -0.068669, -0.076948, -0.082397, -0.094986, -0.105117, -0.107099, -0.108954, -0.112557, -0.110326, -0.100725, -0.096325, -0.096240, -0.092388, -0.081185, -0.071682, -0.065650, -0.062250, -0.057027, -0.054691, -0.048349, -0.042069, -0.032712, -0.027728, -0.023396, -0.018458, -0.008357, -0.005699, -0.011447, -0.020033, -0.026387, -0.030280, -0.028443, -0.023735, -0.023838, -0.031580, -0.034204, -0.027768, -0.018029, -0.010628
	-0.061662, -0.057052, -0.075163, -0.086710, -0.094182, -0.097544, -0.098814, -0.105908, -0.114460, -0.111718, -0.097559, -0.091614, -0.093860, -0.093098, -0.081687, -0.069410, -0.064117, -0.062745, -0.055603, -0.051413, -0.048043, -0.040363, -0.031842, -0.023420, -0.017470, -0.012600, -0.008163, -0.003898, -0.007635, -0.013254, -0.019807, -0.025153, -0.027074, -0.023513, -0.023727, -0.028669, -0.029153, -0.024831, -0.018735, -0.009246
	-0.056176, -0.059439, -0.066501, -0.071527, -0.085216, -0.094918, -0.097595, -0.099419, -0.101847, -0.102015, -0.093849, -0.089867, -0.088840, -0.083167, -0.071832, -0.062522, -0.058023, -0.057771, -0.053050, -0.048285, -0.041374, -0.033527, -0.024473, -0.018428, -0.013958, -0.008161, -0.001196, 0.001754, -0.004016, -0.011132, -0.018325, -0.021813, -0.021514, -0.016948, -0.018061, -0.025702, -0.028671, -0.021470, -0.011028, -0.001934
	-0.059202, -0.050525, -0.065461, -0.076792, -0.084156, -0.088538, -0.090719, -0.096070, -0.105729, -0.105136, -0.090350, -0.083865, -0.087807, -0.086145, -0.074773, -0.064235, -0.057641, -0.055896, -0.051286, -0.046566, -0.042431, -0.034723, -0.023762, -0.014983, -0.009126, -0.004877, 0.000094, 0.003492, -0.000931, -0.005883, -0.011665, -0.015251, -0.016432, -0.016119, -0.015373, -0.018827, -0.019994, -0.017564, -0.012298, 0.002094
	-0.055561, -0.058184, -0.062669, -0.068111, -0.080741, -0.091895, -0.093911, -0.094387, -0.100239, -0.100695, -0.089841, -0.085682, -0.085212, -0.082910, -0.073072, -0.063594, -0.056157, -0.053482, -0.048107, -0.045405, -0.039982, -0.029777, -0.019905, -0.013872, -0.009732, -0.004272, 0.003500, 0.006909, 0.001302, -0.004626, -0.012374, -0.014751, -0.014637, -0.011794, -0.012913, -0.018244, -0.023377, -0.018086, -0.006575, 0.003294
	-0.062834, -0.047300, -0.060870, -0.073023, -0.079303, -0.082121, -0.083623, -0.091321, -0.100996, -0.098896, -0.085406, -0.078881, -0.081932, -0.082077, -0.074409, -0.063158, -0.053822, -0.050328, -0.045077, -0.039678, -0.035825, -0.028532, -0.017793, -0.009121, -0.003444, -0.000905, 0.003990, 0.007745, 0.004595, 0.000143, -0.004555, -0.007411, -0.010850, -0.010100, -0.010079, -0.013177, -0.016434, -0.014663, -0.010248, -0.000213
	-0.054748, -0.053907, -0.057576, -0.063118, -0.072478, -0.081366, -0.084424, -0.086348, -0.089718, -0.089305, -0.081771, -0.076889, -0.076923, -0.073518, -0.067973, -0.057643, -0.050848, -0.046966, -0.041560, -0.036436, -0.029233, -0.020685, -0.010240, -0.004935, -0.001084, 0.002478, 0.009168, 0.014038, 0.010885, 0.004752, -0.001650, -0.004209, -0.003998, -0.002336, -0.003784, -0.010930, -0.016480, -0.012798, -0.003650, 0.002998
	-0.059345, -0.041989, -0.057435, -0.068229, -0.072857, -0.072586, -0.075155, -0.083286, -0.091292, -0.089727, -0.073702, -0.068353, -0.072910, -0.073863, -0.065527, -0.053635, -0.046064, -0.043899, -0.037607, -0.031251, -0.026194, -0.018885, -0.008095, 0.000309, 0.004911, 0.007046, 0.010642, 0.015635, 0.015277, 0.012612, 0.008074, 0.004852, 0.001546, 0.000504, 0.000589, -0.002769, -0.006432, -0.007765, -0.005391, 0.006950
	-0.050324, -0.049088, -0.052417, -0.057257, -0.063818, -0.071057, -0.074636, -0.075459, -0.079445, -0.077368, -0.068788, -0.063940, -0.065040, -0.063419, -0.054864, -0.044910, -0.038774, -0.036951, -0.031149, -0.026080, -0.018383, -0.011985, -0.001732, 0.003893, 0.007180, 0.011120, 0.017429, 0.021738, 0.019167, 0.015812, 0.011027, 0.007243, 0.006720, 0.009346, 0.006598, -0.003776, -0.009199, -0.007592, 0.005481, 0.014396
	-0.058437, -0.035937, -0.050762, -0.060425, -0.061123, -0.059090, -0.062399, -0.072124, -0.080338, -0.074950, -0.060985, -0.054754, -0.059333, -0.060500, -0.051714, -0.038834, -0.031117, -0.031693, -0.025186, -0.017982, -0.014316, -0.010137, 0.000228, 0.008774, 0.014018, 0.016470, 0.019918, 0.022071, 0.021109, 0.019957, 0.018698, 0.015803, 0.013135, 0.011136, 0.008719, 0.003522, -0.000994, 0.000525, 0.006297, 0.018454
	-0.046143, -0.041577, -0.045391, -0.046668, -0.051722, -0.057607, -0.062802, -0.065205, -0.068243, -0.066293, -0.058216, -0.051324, -0.051806, -0.051018, -0.043393, -0.032431, -0.024016, -0.023321, -0.018504, -0.013897, -0.008455, -0.001123, 0.006609, 0.010462, 0.013887, 0.019328, 0.024804, 0.026590, 0.023420, 0.020337, 0.017129, 0.017199, 0.016391, 0.015616, 0.013257, 0.005832, -0.000019, 0.003462, 0.014308, 0.023624
	-0.051989, -0.030294, -0.043380, -0.051339, -0.050711, -0.048193, -0.052258, -0.061218, -0.070507, -0.068810, -0.049476, -0.042352, -0.046018, -0.046673, -0.038670, -0.027263, -0.018137, -0.018587, -0.013603, -0.008482, -0.004647, -0.000011, 0.008230, 0.015652, 0.019436, 0.023069, 0.024762, 0.027750, 0.028115, 0.026227, 0.022220, 0.023166, 0.020341, 0.018455, 0.014918, 0.011932, 0.007138, 0.008523, 0.014718, 0.026201
	-0.041448, -0.035286, -0.036538, -0.037577, -0.044652, -0.049300, -0.051092, -0.052841, -0.058068, -0.056947, -0.046235, -0.038436, -0.037494, -0.034175, -0.028932, -0.016904, -0.010075, -0.010552, -0.004464, -0.001243, 0.003236, 0.010200, 0.015604, 0.020362, 0.023157, 0.028023, 0.032826, 0.035958, 0.034819, 0.030600, 0.025988, 0.026013, 0.026284, 0.025661, 0.022322, 0.013336, 0.006464, 0.011312, 0.022330, 0.031668
	-0.048540, -0.022534, -0.035260, -0.042156, -0.042749, -0.037408, -0.038818, -0.047322, -0.056808, -0.053643, -0.035691, -0.027822, -0.028789, -0.028255, -0.020274, -0.007285, -0.000723, -0.000788, 0.005440, 0.008938, 0.008953, 0.012074, 0.017957, 0.025241, 0.029175, 0.032057, 0.033733, 0.038359, 0.039349, 0.037161, 0.034052, 0.034585, 0.032020, 0.029940, 0.026326, 0.024577, 0.020432, 0.021586, 0.024568, 0.034552
	-0.033086, -0.027982, -0.029443, -0.029011, -0.035629, -0.040579, -0.038290, -0.037389, -0.041260, -0.040430, -0.032279, -0.021394, -0.018817, -0.015525, -0.007558, 0.006345, 0.011048, 0.011271, 0.013497, 0.017030, 0.017449, 0.022752, 0.026764, 0.030722, 0.033532, 0.037203, 0.043356, 0.048536, 0.047776, 0.043851, 0.039311, 0.039944, 0.039954, 0.038931, 0.034893, 0.030946, 0.023127, 0.027359, 0.034859, 0.043920
	-0.036218, -0.016846, -0.030897, -0.036980, -0.037261, -0.033334, -0.030888, -0.034074, -0.042142, -0.039980, -0.021377, -0.013603, -0.014171, -0.013131, -0.001768, 0.014998, 0.020060, 0.018173, 0.019934, 0.024704, 0.023739, 0.024617, 0.027288, 0.035116, 0.041187, 0.043128, 0.045921, 0.051709, 0.053031, 0.050698, 0.047697, 0.047728, 0.046845, 0.043201, 0.041805, 0.040728, 0.036184, 0.034435, 0.035120, 0.045329
	-0.029808, -0.023871, -0.026541, -0.026705, -0.031203, -0.036908, -0.034411, -0.029231, -0.028090, -0.026102, -0.016691, -0.007747, -0.004471, 0.001560, 0.010738, 0.025062, 0.027672, 0.024833, 0.026976, 0.029502, 0.030754, 0.035709, 0.039403, 0.044719, 0.046379, 0.049250, 0.054178, 0.059793, 0.059542, 0.052111, 0.047608, 0.050103, 0.053142, 0.052747, 0.050045, 0.044102, 0.033149, 0.035392, 0.045678, 0.054080
	-0.032238, -0.008993, -0.023999, -0.030969, -0.028658, -0.024887, -0.024493, -0.028088, -0.031053, -0.022849, -0.003868, 0.004647, 0.004540, 0.007560, 0.018373, 0.031401, 0.035778, 0.033768, 0.035173, 0.035884, 0.036597, 0.038940, 0.044566, 0.053914, 0.056554, 0.056382, 0.056449, 0.060387, 0.062696, 0.058223, 0.055016, 0.056193, 0.056891, 0.052793, 0.052741, 0.052626, 0.048117, 0.045032, 0.048033, 0.055100
	-0.019758, -0.015110, -0.017814, -0.018871, -0.023340, -0.028653, -0.026880, -0.018681, -0.017020, -0.011343, -0.001002, 0.008249, 0.014012, 0.020367, 0.026878, 0.038534, 0.041827, 0.039532, 0.039775, 0.039109, 0.043172, 0.049325, 0.056604, 0.059583, 0.059329, 0.059876, 0.062766, 0.068759, 0.067214, 0.059657, 0.055950, 0.056798, 0.058619, 0.058591, 0.059849, 0.056473, 0.046841, 0.047921, 0.058342, 0.065346
	-0.018628, -0.000296, -0.014764, -0.022634, -0.020483, -0.016362, -0.015485, -0.017352, -0.020246, -0.010362, 0.008635, 0.018414, 0.018542, 0.024258, 0.033370, 0.045728, 0.049983, 0.044610, 0.044638, 0.047649, 0.049220, 0.051954, 0.058932, 0.065915, 0.069102, 0.067410, 0.067680, 0.073734, 0.072203, 0.067293, 0.063945, 0.064378, 0.065047, 0.061989, 0.062882, 0.063468, 0.059707, 0.057986, 0.059739, 0.066139
	-0.010091, -0.006551, -0.008018, -0.009589, -0.016068, -0.020662, -0.019451, -0.010985, -0.009391, -0.003580, 0.007826, 0.019598, 0.024961, 0.033762, 0.040618, 0.050868, 0.052139, 0.050495, 0.049198, 0.051777, 0.056840, 0.061771, 0.068414, 0.072295, 0.073443, 0.072145, 0.073414, 0.079338, 0.075988, 0.067367, 0.064745, 0.064435, 0.066982, 0.065811, 0.067424, 0.063230, 0.058438, 0.059982, 0.067672, 0.072460
	-0.016254, 0.006291, -0.008031, -0.013944, -0.014475, -0.010741, -0.009932, -0.011709, -0.015503, -0.006971, 0.013190, 0.024865, 0.029121, 0.033942, 0.044335, 0.054572, 0.058078, 0.055224, 0.055897, 0.058327, 0.061207, 0.063939, 0.070506, 0.078141, 0.084203, 0.081223, 0.079519, 0.082883, 0.080890, 0.076174, 0.071279, 0.073064, 0.071225, 0.066859, 0.069860, 0.070836, 0.069427, 0.069140, 0.070950, 0.075269
	-0.008127, 0.000730, 0.001164, -0.000308, -0.006659, -0.012343, -0.011463, -0.003755, -0.001876, 0.005166, 0.016616, 0.030243, 0.036509, 0.045020, 0.053681, 0.063738, 0.066425, 0.063964, 0.062796, 0.065633, 0.071912, 0.077280, 0.082580, 0.086477, 0.089798, 0.089603, 0.091453, 0.096125, 0.088708, 0.079903, 0.074317, 0.076190, 0.075399, 0.075242, 0.079628, 0.077855, 0.071473, 0.073702, 0.082757, 0.088086
	-0.010951, 0.013218, -0.000878, -0.006241, -0.005623, 0.000046, 0.000158, -0.002943, -0.005314, 0.005491, 0.026890, 0.035754, 0.041490, 0.045829, 0.059325, 0.070249, 0.074114, 0.071815, 0.073229, 0.076313, 0.080778, 0.081554, 0.087919, 0.096206, 0.101562, 0.101674, 0.100494, 0.103989, 0.100292, 0.093977, 0.088080, 0.088136, 0.086555, 0.081494, 0.084966, 0.087073, 0.084113, 0.085184, 0.087700, 0.092188
	-0.002972, 0.006020, 0.006098, 0.004303, 0.001326, -0.002386, -0.001840, 0.005325, 0.008624, 0.016246, 0.026781, 0.039696, 0.048540, 0.055938, 0.066982, 0.076497, 0.080828, 0.079669, 0.080127, 0.083754, 0.089783, 0.093456, 0.100570, 0.105322, 0.107132, 0.110571, 0.113141, 0.118064, 0.111721, 0.101634, 0.093555, 0.093112, 0.093104, 0.092325, 0.094780, 0.092552, 0.085283, 0.088882, 0.097508, 0.105280
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 11.4
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Preperations]
version = 1
points = 
	0.012158, -0.006098, -0.020628, -0.034069, -0.049418, -0.058491, -0.062706, -0.063181, -0.065552, -0.063461, -0.057373, -0.056717, -0.056579, -0.054080, -0.053373, -0.056878, -0.057281, -0.055224, -0.049676, -0.047605, -0.041454, -0.034605, -0.022490, -0.011292, -0.009411, -0.005344, -0.003510, -0.002717, -0.005999, -0.010712, -0.013141, -0.015611, -0.020004, -0.017667, -0.016629, -0.022248, -0.024864, -0.024065, -0.014921, -0.010826
	-0.005958, -0.021084, -0.033800, -0.047903, -0.059950, -0.071345, -0.072502, -0.073350, -0.075852, -0.072963, -0.067236, -0.064315, -0.065698, -0.064338, -0.062871, -0.065238, -0.067095, -0.063584, -0.059241, -0.057846, -0.051380, -0.043157, -0.030230, -0.019950, -0.018121, -0.014291, -0.009354, -0.013065, -0.016464, -0.022925, -0.025337, -0.026541, -0.030577, -0.029068, -0.027094, -0.030532, -0.034241, -0.032625, -0.021498, -0.020513
	-0.017526, -0.027763, -0.040710, -0.055305, -0.068172, -0.079641, -0.081247, -0.081903, -0.083679, -0.081855, -0.073270, -0.070340, -0.072083, -0.071536, -0.066055, -0.065901, -0.069085, -0.066531, -0.063284, -0.061616, -0.053366, -0.047292, -0.035451, -0.023167, -0.022205, -0.016699, -0.012552, -0.014153, -0.018802, -0.030443, -0.032210, -0.034051, -0.034437, -0.031439, -0.030406, -0.032817, -0.036351, -0.034849, -0.024250, -0.019489
	-0.017750, -0.030284, -0.043463, -0.055839, -0.071865, -0.084888, -0.086157, -0.084619, -0.086681, -0.084515, -0.075246, -0.073263, -0.075604, -0.075123, -0.069177, -0.070723, -0.071097, -0.068644, -0.065465, -0.063718, -0.057574, -0.049335, -0.036556, -0.028418, -0.028259, -0.023387, -0.018454, -0.020519, -0.027499, -0.038314, -0.041534, -0.041886, -0.039972, -0.036438, -0.033959, -0.033009, -0.038291, -0.036339, -0.022688, -0.024783
	-0.021354, -0.034103, -0.047541, -0.060551, -0.075691, -0.089373, -0.092241, -0.091621, -0.093203, -0.090723, -0.082480, -0.079781, -0.079706, -0.079674, -0.074365, -0.073780, -0.073465, -0.070165, -0.064970, -0.065503, -0.059104, -0.051038, -0.041817, -0.031243, -0.031386, -0.028837, -0.023658, -0.024237, -0.029641, -0.039210, -0.042766, -0.044461, -0.041863, -0.039075, -0.034881, -0.034571, -0.039386, -0.038253, -0.031659, -0.024202
	-0.027696, -0.041184, -0.054054, -0.064759, -0.080898, -0.094964, -0.097906, -0.098033, -0.101256, -0.098300, -0.091517, -0.088420, -0.086945, -0.085220, -0.079938, -0.079979, -0.079828, -0.074842, -0.072903, -0.072415, -0.065384, -0.057454, -0.048482, -0.040977, -0.039336, -0.036065, -0.032553, -0.034336, -0.039337, -0.046271, -0.049398, -0.051220, -0.049530, -0.045000, -0.045029, -0.042100, -0.049767, -0.046386, -0.035574, -0.032188
	-0.033426, -0.046259, -0.059363, -0.068024, -0.084858, -0.097009, -0.103434, -0.106215, -0.107319, -0.106178, -0.100333, -0.097536, -0.095352, -0.091322, -0.086332, -0.082309, -0.081440, -0.078413, -0.075067, -0.073134, -0.068255, -0.062667, -0.054300, -0.046004, -0.042001, -0.039181, -0.035010, -0.036092, -0.041599, -0.048788, -0.051751, -0.051179, -0.051019, -0.049121, -0.045860, -0.046756, -0.050005, -0.051613, -0.040237, -0.035349
	-0.037931, -0.051993, -0.066455, -0.075044, -0.088177, -0.102890, -0.108223, -0.112373, -0.115787, -0.113421, -0.108543, -0.105936, -0.101048, -0.096863, -0.090726, -0.087882, -0.086665, -0.083874, -0.081096, -0.080894, -0.075125, -0.071038, -0.063072, -0.054696, -0.051039, -0.046728, -0.042566, -0.043887, -0.048745, -0.056834, -0.059808, -0.060521, -0.060664, -0.057968, -0.056317, -0.052477, -0.058814, -0.055877, -0.046325, -0.042545
	-0.041429, -0.053634, -0.067633, -0.077111, -0.090998, -0.103561, -0.109445, -0.114741, -0.120075, -0.119821, -0.114703, -0.110411, -0.105589, -0.099826, -0.093730, -0.089705, -0.087199, -0.086439, -0.082688, -0.082221, -0.078348, -0.073203, -0.065273, -0.058731, -0.054025, -0.049231, -0.044830, -0.043830, -0.045839, -0.054137, -0.059075, -0.059515, -0.058546, -0.056956, -0.054145, -0.053129, -0.056587, -0.056341, -0.047057, -0.039936
	-0.044295, -0.058972, -0.072101, -0.082726, -0.095001, -0.106449, -0.111505, -0.118363, -0.124608, -0.123506, -0.120263, -0.115400, -0.110227, -0.104535, -0.100348, -0.095757, -0.092961, -0.092377, -0.089613, -0.088047, -0.084834, -0.079314, -0.072500, -0.064519, -0.060449, -0.055767, -0.051803, -0.050997, -0.052855, -0.058115, -0.063348, -0.065363, -0.067936, -0.063474, -0.061475, -0.054726, -0.062529, -0.055352, -0.048878, -0.044991
	-0.045804, -0.056574, -0.073308, -0.082450, -0.097495, -0.107467, -0.111501, -0.116418, -0.126724, -0.125980, -0.123231, -0.120494, -0.114667, -0.111289, -0.103451, -0.099228, -0.095880, -0.095882, -0.093328, -0.091000, -0.087051, -0.081909, -0.075949, -0.064971, -0.061050, -0.055137, -0.049046, -0.047319, -0.049806, -0.056968, -0.059608, -0.060249, -0.063032, -0.060556, -0.056284, -0.056263, -0.058891, -0.057890, -0.051554, -0.042382
	-0.049818, -0.062681, -0.076305, -0.084328, -0.098717, -0.107866, -0.113937, -0.120088, -0.128622, -0.128931, -0.126353, -0.123191, -0.118529, -0.115642, -0.106288, -0.103976, -0.099708, -0.097750, -0.094501, -0.094545, -0.090910, -0.085952, -0.077352, -0.067196, -0.062435, -0.057738, -0.052934, -0.051098, -0.055294, -0.061112, -0.063120, -0.067525, -0.067979, -0.066558, -0.064608, -0.060597, -0.067812, -0.057641, -0.056224, -0.046471
	-0.050591, -0.060432, -0.075602, -0.083877, -0.096933, -0.106147, -0.112334, -0.118295, -0.127966, -0.128757, -0.125157, -0.121831, -0.118557, -0.116124, -0.108723, -0.104502, -0.099469, -0.095841, -0.090662, -0.089822, -0.087969, -0.084545, -0.076375, -0.064821, -0.059093, -0.053427, -0.047372, -0.044341, -0.047964, -0.054064, -0.057133, -0.059152, -0.061568, -0.059109, -0.056640, -0.056691, -0.056844, -0.054564, -0.048514, -0.040641
	-0.047704, -0.059564, -0.073127, -0.080945, -0.093764, -0.105483, -0.111501, -0.118792, -0.124812, -0.126576, -0.122064, -0.118087, -0.116126, -0.114867, -0.108053, -0.103336, -0.097558, -0.093250, -0.086537, -0.085303, -0.083677, -0.079292, -0.070542, -0.062526, -0.056818, -0.052534, -0.044035, -0.041353, -0.046942, -0.051329, -0.055481, -0.062777, -0.058499, -0.058025, -0.057390, -0.053562, -0.060843, -0.046555, -0.046260, -0.036083
	-0.046496, -0.052983, -0.067518, -0.076904, -0.091704, -0.103105, -0.111995, -0.117751, -0.122307, -0.122941, -0.118230, -0.115004, -0.114258, -0.113138, -0.105515, -0.098417, -0.093384, -0.090070, -0.083281, -0.079846, -0.078725, -0.075452, -0.066225, -0.057269, -0.053103, -0.047808, -0.039772, -0.036834, -0.041270, -0.047376, -0.051111, -0.053848, -0.053029, -0.050301, -0.048919, -0.050775, -0.050121, -0.046842, -0.039633, -0.030497
	-0.040695, -0.051685, -0.064038, -0.070974, -0.086679, -0.101773, -0.109889, -0.114373, -0.117883, -0.118764, -0.113125, -0.110931, -0.111099, -0.109664, -0.098733, -0.093182, -0.090154, -0.086213, -0.077214, -0.077108, -0.075555, -0.069117, -0.060704, -0.054093, -0.049253, -0.044799, -0.037536, -0.035304, -0.040134, -0.045456, -0.051720, -0.056675, -0.053743, -0.052923, -0.049701, -0.050238, -0.056776, -0.041485, -0.041755, -0.027329
	-0.039842, -0.039428, -0.055732, -0.063890, -0.079179, -0.092823, -0.101698, -0.106156, -0.111709, -0.113152, -0.108033, -0.104872, -0.105645, -0.103501, -0.094487, -0.087264, -0.084273, -0.080950, -0.074116, -0.070973, -0.068409, -0.062825, -0.054757, -0.044150, -0.040620, -0.036602, -0.031538, -0.026478, -0.031123, -0.037600, -0.042341, -0.046700, -0.047380, -0.042880, -0.040967, -0.045367, -0.044192, -0.038553, -0.029948, -0.020790
	-0.030596, -0.038279, -0.051528, -0.058981, -0.073983, -0.089044, -0.099173, -0.101740, -0.104830, -0.107083, -0.102306, -0.101554, -0.101336, -0.097146, -0.089217, -0.083800, -0.080621, -0.078071, -0.071535, -0.068328, -0.065806, -0.056882, -0.048683, -0.039756, -0.036349, -0.031328, -0.025351, -0.024133, -0.029773, -0.033858, -0.040011, -0.044146, -0.043900, -0.044797, -0.038019, -0.042319, -0.047297, -0.031851, -0.034318, -0.013527
	-0.032121, -0.034722, -0.047839, -0.054710, -0.069175, -0.084213, -0.094533, -0.097233, -0.100863, -0.104775, -0.099781, -0.097416, -0.098804, -0.096059, -0.086694, -0.079692, -0.076749, -0.074609, -0.068106, -0.063906, -0.061136, -0.055447, -0.045559, -0.035389, -0.029696, -0.025708, -0.020034, -0.017335, -0.022665, -0.028532, -0.032369, -0.035760, -0.037212, -0.035201, -0.032872, -0.034132, -0.035907, -0.032127, -0.025026, -0.009282
	-0.026707, -0.034374, -0.045183, -0.052691, -0.067014, -0.084964, -0.092286, -0.094441, -0.099291, -0.103609, -0.098278, -0.094972, -0.097169, -0.095394, -0.086653, -0.080205, -0.076284, -0.070594, -0.064535, -0.062012, -0.060174, -0.051216, -0.040622, -0.033396, -0.029636, -0.024235, -0.017274, -0.018232, -0.021459, -0.024778, -0.031754, -0.034481, -0.033398, -0.037949, -0.030432, -0.033219, -0.038432, -0.021975, -0.030052, -0.009295
	-0.028559, -0.029280, -0.042071, -0.048655, -0.061603, -0.076257, -0.086817, -0.091815, -0.095682, -0.098682, -0.093729, -0.091168, -0.092213, -0.090073, -0.084070, -0.077048, -0.072045, -0.066267, -0.060309, -0.053639, -0.051696, -0.046852, -0.034069, -0.025602, -0.020640, -0.018021, -0.013180, -0.009049, -0.013846, -0.018012, -0.021061, -0.024515, -0.027068, -0.026804, -0.024283, -0.025595, -0.028234, -0.025272, -0.019246, -0.008595
	-0.025711, -0.029003, -0.038836, -0.048015, -0.058511, -0.074480, -0.083738, -0.087945, -0.091439, -0.094310, -0.090288, -0.087858, -0.088589, -0.086163, -0.081829, -0.075146, -0.071136, -0.064399, -0.057338, -0.052103, -0.049650, -0.043210, -0.032998, -0.023124, -0.020191, -0.016625, -0.012433, -0.010465, -0.009871, -0.015007, -0.021217, -0.021582, -0.023800, -0.027652, -0.021527, -0.027137, -0.030828, -0.020152, -0.026202, -0.008568
	-0.031287, -0.022523, -0.035800, -0.041583, -0.052691, -0.065901, -0.075941, -0.079246, -0.083936, -0.086778, -0.082235, -0.078893, -0.080642, -0.079419, -0.074324, -0.067418, -0.062113, -0.057744, -0.049923, -0.043390, -0.040055, -0.035512, -0.023838, -0.015485, -0.009895, -0.008346, -0.005387, 0.001467, -0.000104, -0.003777, -0.007926, -0.012023, -0.013970, -0.014207, -0.013994, -0.017009, -0.019233, -0.019282, -0.014210, -0.001146
	-0.020719, -0.024043, -0.035160, -0.041635, -0.051902, -0.063884, -0.072884, -0.076738, -0.081856, -0.083761, -0.077857, -0.074651, -0.077952, -0.076310, -0.069721, -0.063240, -0.056775, -0.055188, -0.046711, -0.042996, -0.039499, -0.032268, -0.023129, -0.015735, -0.012305, -0.009383, -0.005789, -0.001996, -0.001166, -0.005106, -0.009634, -0.009864, -0.011905, -0.015913, -0.010246, -0.016645, -0.022975, -0.011972, -0.018524, 0.001048
	-0.026050, -0.019774, -0.032555, -0.037813, -0.044657, -0.054435, -0.065271, -0.071019, -0.075585, -0.077479, -0.072635, -0.069526, -0.071046, -0.070770, -0.063085, -0.055960, -0.050956, -0.049593, -0.042773, -0.034996, -0.032645, -0.029030, -0.020343, -0.011008, -0.005751, -0.003252, 0.000746, 0.003215, 0.001749, -0.000068, -0.001413, -0.002608, -0.005837, -0.007103, -0.008431, -0.012027, -0.015656, -0.014417, -0.006321, 0.003748
	-0.021728, -0.019178, -0.031232, -0.036249, -0.042206, -0.053190, -0.064017, -0.068545, -0.074597, -0.074544, -0.069543, -0.065779, -0.067928, -0.067354, -0.060655, -0.052790, -0.047723, -0.046044, -0.038188, -0.034539, -0.032080, -0.027152, -0.018902, -0.012508, -0.009304, -0.003955, -0.000288, -0.001549, -0.000556, -0.003756, -0.008467, -0.003851, -0.005999, -0.012959, -0.007423, -0.015332, -0.017388, -0.005695, -0.010807, 0.007710
	-0.028204, -0.017096, -0.027984, -0.032129, -0.038374, -0.046561, -0.059356, -0.061847, -0.069228, -0.070551, -0.065474, -0.059719, -0.059893, -0.060271, -0.053666, -0.047202, -0.041189, -0.039979, -0.033189, -0.028761, -0.025714, -0.021660, -0.014905, -0.007841, -0.004669, -0.001174, 0.001874, 0.005613, 0.005527, 0.001504, -0.000694, 0.001892, 0.001885, -0.002506, -0.005619, -0.007166, -0.009935, -0.007406, 0.000545, 0.009983
	-0.019393, -0.017785, -0.025482, -0.028146, -0.036861, -0.047528, -0.055696, -0.059118, -0.064151, -0.066346, -0.060565, -0.055661, -0.055495, -0.051944, -0.048147, -0.040645, -0.036359, -0.035990, -0.026764, -0.024843, -0.023572, -0.019648, -0.013807, -0.006811, -0.004589, -0.000266, 0.003010, 0.004931, 0.006834, 0.003254, -0.001690, 0.003120, 0.001036, -0.005283, 0.000659, -0.007399, -0.010996, -0.000832, -0.006381, 0.012135
	-0.021519, -0.010062, -0.018662, -0.023011, -0.029067, -0.036961, -0.043194, -0.048197, -0.053632, -0.055489, -0.050054, -0.045247, -0.042655, -0.040243, -0.034315, -0.027094, -0.022697, -0.021644, -0.015333, -0.010768, -0.013712, -0.012051, -0.005326, 0.000560, 0.005300, 0.007429, 0.009930, 0.015968, 0.016454, 0.012383, 0.010385, 0.011612, 0.011413, 0.008357, 0.006831, 0.005524, 0.003087, 0.003507, 0.009876, 0.018892
	-0.017331, -0.015238, -0.021971, -0.024651, -0.029507, -0.040209, -0.044232, -0.046101, -0.052689, -0.053151, -0.047133, -0.042985, -0.040475, -0.037020, -0.029999, -0.021348, -0.018232, -0.017876, -0.013058, -0.008535, -0.013279, -0.011527, -0.006296, -0.001615, 0.002270, 0.006991, 0.010272, 0.013407, 0.015950, 0.012503, 0.008026, 0.013701, 0.011513, 0.004867, 0.010667, 0.006774, 0.003571, 0.012416, 0.004875, 0.020961
	-0.022637, -0.011107, -0.018340, -0.023896, -0.028320, -0.038092, -0.041212, -0.041642, -0.044537, -0.046015, -0.041699, -0.035805, -0.033527, -0.030911, -0.022925, -0.010175, -0.007279, -0.008644, -0.005065, -0.000597, -0.003797, -0.004052, 0.000635, 0.006175, 0.010857, 0.012993, 0.016956, 0.022765, 0.023298, 0.020262, 0.018285, 0.019467, 0.021161, 0.018785, 0.017891, 0.017817, 0.013874, 0.012825, 0.015904, 0.025844
	-0.014532, -0.010189, -0.019385, -0.022584, -0.028159, -0.037803, -0.040566, -0.038125, -0.040339, -0.038899, -0.033171, -0.028143, -0.025641, -0.019755, -0.012463, -0.003824, -0.000871, -0.002698, -0.000197, 0.001952, -0.001353, -0.000188, 0.004902, 0.012600, 0.014373, 0.016449, 0.018872, 0.022822, 0.026385, 0.020681, 0.015275, 0.021387, 0.023535, 0.016733, 0.022161, 0.018819, 0.011276, 0.020785, 0.014683, 0.032409
	-0.016972, -0.004835, -0.015539, -0.019706, -0.022971, -0.032222, -0.037732, -0.035551, -0.033892, -0.031679, -0.024624, -0.019946, -0.016412, -0.010040, -0.003445, 0.005991, 0.008364, 0.006410, 0.008289, 0.009260, 0.007409, 0.008691, 0.015230, 0.022729, 0.025465, 0.025502, 0.026102, 0.030309, 0.031861, 0.026963, 0.024651, 0.027000, 0.029039, 0.025577, 0.027217, 0.027660, 0.023245, 0.021705, 0.026383, 0.034120
	-0.007042, -0.003943, -0.013314, -0.016082, -0.020497, -0.030911, -0.035096, -0.030889, -0.029351, -0.025337, -0.018980, -0.012449, -0.008879, -0.001902, 0.003577, 0.011256, 0.012460, 0.010502, 0.011904, 0.011483, 0.010067, 0.013356, 0.020792, 0.027368, 0.026382, 0.028554, 0.028164, 0.029993, 0.033232, 0.028830, 0.022354, 0.027991, 0.029607, 0.020011, 0.031066, 0.031755, 0.025061, 0.037228, 0.024607, 0.041453
	-0.012463, -0.000987, -0.008994, -0.014815, -0.017487, -0.026372, -0.031392, -0.028459, -0.025402, -0.024153, -0.015566, -0.007862, -0.004579, 0.001484, 0.010757, 0.017401, 0.019536, 0.016264, 0.016278, 0.018231, 0.018193, 0.018217, 0.025442, 0.034794, 0.036179, 0.034770, 0.033985, 0.040104, 0.040404, 0.034161, 0.030977, 0.032380, 0.034144, 0.031909, 0.033231, 0.035957, 0.034171, 0.033050, 0.038776, 0.042972
	-0.002758, 0.000700, -0.008467, -0.011525, -0.018705, -0.027522, -0.031609, -0.027494, -0.026315, -0.023221, -0.014164, -0.006562, -0.002205, 0.006453, 0.013689, 0.018647, 0.017673, 0.016751, 0.017380, 0.018782, 0.019038, 0.021992, 0.027475, 0.034748, 0.036870, 0.036635, 0.035394, 0.037519, 0.038008, 0.032063, 0.025834, 0.030409, 0.033142, 0.023991, 0.034882, 0.034323, 0.030317, 0.042711, 0.030793, 0.045129
	-0.011501, 0.004979, -0.003199, -0.009532, -0.013737, -0.022490, -0.028056, -0.025047, -0.023987, -0.021727, -0.011113, -0.003633, 0.003070, 0.010580, 0.020230, 0.025058, 0.026653, 0.024592, 0.024567, 0.025613, 0.027386, 0.029282, 0.037705, 0.042901, 0.046601, 0.045443, 0.044217, 0.048155, 0.045715, 0.039788, 0.034981, 0.038594, 0.038594, 0.034532, 0.038671, 0.042065, 0.040659, 0.042101, 0.045919, 0.050030
	-0.005239, 0.006624, -0.001837, -0.005350, -0.012024, -0.022230, -0.026144, -0.022704, -0.021559, -0.017450, -0.008515, 0.000433, 0.007392, 0.014546, 0.023538, 0.029043, 0.029892, 0.027280, 0.028785, 0.030662, 0.032758, 0.032649, 0.040035, 0.046372, 0.048654, 0.050330, 0.049538, 0.049746, 0.048851, 0.041068, 0.034598, 0.041375, 0.041379, 0.030621, 0.043091, 0.044712, 0.038634, 0.053475, 0.042814, 0.059369
	-0.011843, 0.005417, 0.000007, -0.005709, -0.011391, -0.019100, -0.024151, -0.021274, -0.019356, -0.016953, -0.004422, 0.002891, 0.010688, 0.018353, 0.027665, 0.035281, 0.036655, 0.034937, 0.036795, 0.039994, 0.042705, 0.042668, 0.048600, 0.055673, 0.059602, 0.061002, 0.059934, 0.064283, 0.061835, 0.052838, 0.048644, 0.048401, 0.048158, 0.044262, 0.049173, 0.053313, 0.050054, 0.051718, 0.058112, 0.062677
	-0.003249, 0.007140, -0.000190, -0.005182, -0.010664, -0.017472, -0.021072, -0.018928, -0.015929, -0.011810, -0.001170, 0.006999, 0.014346, 0.022026, 0.033087, 0.037703, 0.039304, 0.038986, 0.040531, 0.042739, 0.044912, 0.045850, 0.052980, 0.060894, 0.062495, 0.065477, 0.066306, 0.069035, 0.066301, 0.058359, 0.048879, 0.054660, 0.053906, 0.042834, 0.051292, 0.054304, 0.049390, 0.064968, 0.053062, 0.067337
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 80.0
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Peperations]
version = 1
points = 
	0.022498, 0.020830, 0.014175, -0.000111, -0.007965, -0.011932, -0.009252, -0.003320, -0.000118, 0.004151, 0.015991, 0.024593, 0.030148, 0.034696, 0.042241, 0.043592, 0.045307, 0.051419, 0.057700, 0.066468, 0.072764, 0.085492, 0.100446, 0.113063, 0.118900, 0.122870, 0.130290, 0.129755, 0.129462, 0.124089, 0.122420, 0.123461, 0.116841, 0.117893, 0.119241, 0.115227, 0.110631, 0.109920, 0.117187, 0.124332
	0.004953, 0.000716, -0.005511, -0.010742, -0.018400, -0.024021, -0.019665, -0.013525, -0.009878, -0.004126, 0.008939, 0.016408, 0.019292, 0.023840, 0.033007, 0.033600, 0.034448, 0.041047, 0.049029, 0.052882, 0.062512, 0.072410, 0.089182, 0.103027, 0.106205, 0.110789, 0.117912, 0.115269, 0.112784, 0.106051, 0.103603, 0.104209, 0.099603, 0.105100, 0.101466, 0.099610, 0.095780, 0.096420, 0.108661, 0.108286
	-0.007933, -0.002801, -0.011350, -0.022484, -0.029473, -0.033231, -0.030354, -0.021826, -0.018408, -0.013209, 0.001640, 0.008984, 0.012027, 0.014149, 0.024334, 0.028649, 0.030597, 0.034667, 0.041223, 0.046241, 0.051968, 0.062511, 0.079099, 0.090699, 0.097837, 0.101667, 0.108218, 0.106595, 0.104490, 0.095444, 0.089512, 0.089259, 0.089179, 0.091741, 0.094161, 0.094254, 0.091002, 0.088753, 0.095405, 0.102343
	-0.010759, -0.012564, -0.018170, -0.023960, -0.033106, -0.040910, -0.038354, -0.031441, -0.026122, -0.019953, -0.006267, 0.000733, 0.002678, 0.006102, 0.015437, 0.019860, 0.022689, 0.029563, 0.035629, 0.037302, 0.045089, 0.055137, 0.070820, 0.082978, 0.087158, 0.088614, 0.094487, 0.093851, 0.091038, 0.080923, 0.074433, 0.073797, 0.073058, 0.081788, 0.080734, 0.083111, 0.078149, 0.079373, 0.091335, 0.087853
	-0.027313, -0.019238, -0.027920, -0.036645, -0.043223, -0.049872, -0.048503, -0.043853, -0.040737, -0.035179, -0.021622, -0.013493, -0.010171, -0.007317, 0.001347, 0.007440, 0.011360, 0.015985, 0.023916, 0.026329, 0.031680, 0.042865, 0.056754, 0.067621, 0.072919, 0.075964, 0.080156, 0.081233, 0.077771, 0.068443, 0.063939, 0.062251, 0.063828, 0.065094, 0.069498, 0.071735, 0.067423, 0.064065, 0.069162, 0.076272
	-0.033298, -0.035618, -0.039940, -0.043358, -0.050731, -0.061413, -0.060545, -0.055944, -0.052261, -0.045471, -0.035624, -0.027633, -0.021472, -0.017300, -0.006949, -0.002776, -0.000154, 0.006413, 0.012882, 0.014721, 0.023411, 0.031711, 0.040565, 0.054702, 0.058761, 0.061734, 0.065369, 0.066037, 0.061059, 0.053849, 0.049600, 0.048373, 0.049189, 0.054631, 0.050470, 0.056349, 0.047074, 0.049651, 0.057444, 0.057485
	-0.046284, -0.039039, -0.049010, -0.054961, -0.061001, -0.068408, -0.069602, -0.066474, -0.063117, -0.059357, -0.049570, -0.041166, -0.035441, -0.029269, -0.019658, -0.012395, -0.008906, -0.005538, 0.002012, 0.008339, 0.013216, 0.018793, 0.031185, 0.040165, 0.047175, 0.050605, 0.054283, 0.054442, 0.049166, 0.043483, 0.039000, 0.040758, 0.040857, 0.040759, 0.042263, 0.043438, 0.040051, 0.035886, 0.041332, 0.048851
	-0.049893, -0.051919, -0.058103, -0.060142, -0.067656, -0.077159, -0.079195, -0.078019, -0.075421, -0.069471, -0.060409, -0.054194, -0.044226, -0.037275, -0.027912, -0.020020, -0.016789, -0.012491, -0.003457, 0.001129, 0.004540, 0.009435, 0.018232, 0.027941, 0.035138, 0.038227, 0.042656, 0.044103, 0.038517, 0.032121, 0.029666, 0.027319, 0.029774, 0.031572, 0.028887, 0.034828, 0.023795, 0.030023, 0.033606, 0.036047
	-0.061015, -0.055279, -0.067497, -0.072234, -0.078637, -0.083600, -0.085954, -0.087271, -0.088647, -0.083447, -0.073398, -0.065920, -0.058009, -0.048810, -0.040714, -0.032533, -0.027328, -0.020402, -0.011382, -0.006547, -0.005452, -0.002712, 0.004649, 0.014201, 0.021442, 0.025510, 0.032890, 0.034711, 0.030965, 0.026329, 0.018828, 0.019246, 0.018861, 0.019611, 0.020596, 0.021396, 0.020172, 0.015723, 0.020537, 0.029677
	-0.063777, -0.066149, -0.073750, -0.076131, -0.084016, -0.091900, -0.093741, -0.094496, -0.094840, -0.089548, -0.084332, -0.077263, -0.068485, -0.061963, -0.051082, -0.043658, -0.037912, -0.032323, -0.024324, -0.019914, -0.018261, -0.013727, -0.003485, 0.004316, 0.011418, 0.017023, 0.022980, 0.024505, 0.018896, 0.014000, 0.009498, 0.006074, 0.009480, 0.007611, 0.008958, 0.010086, -0.000341, 0.010423, 0.010467, 0.016794
	-0.072341, -0.064233, -0.079217, -0.084483, -0.091050, -0.094481, -0.095378, -0.096667, -0.100564, -0.098313, -0.093254, -0.086700, -0.079209, -0.071795, -0.061313, -0.051911, -0.046317, -0.042643, -0.037228, -0.031598, -0.027431, -0.020480, -0.012883, -0.003114, 0.004746, 0.010189, 0.015911, 0.017106, 0.014037, 0.008693, 0.005120, 0.003652, -0.000532, -0.001097, 0.001984, 0.000397, -0.002089, -0.002821, 0.000529, 0.009043
	-0.068927, -0.075835, -0.083530, -0.085213, -0.091299, -0.100015, -0.101020, -0.100921, -0.103349, -0.102493, -0.098069, -0.091292, -0.083452, -0.079672, -0.069612, -0.062472, -0.055862, -0.052233, -0.046746, -0.041991, -0.035219, -0.028225, -0.018698, -0.007309, -0.002458, 0.002051, 0.006595, 0.008468, 0.005218, -0.000205, -0.003131, -0.003647, -0.006151, -0.009154, -0.005539, -0.006971, -0.015297, -0.002874, -0.005242, 0.003706
	-0.070116, -0.067835, -0.086390, -0.089881, -0.095167, -0.099194, -0.100751, -0.103794, -0.106996, -0.105835, -0.098564, -0.092154, -0.085579, -0.083053, -0.074722, -0.066442, -0.059302, -0.053429, -0.047800, -0.042952, -0.039132, -0.034614, -0.025732, -0.012689, -0.005906, 0.001101, 0.006644, 0.010980, 0.007742, 0.002526, -0.000261, -0.004094, -0.008771, -0.008465, -0.007095, -0.008952, -0.010405, -0.010446, -0.006121, 0.002024
	-0.064366, -0.071780, -0.082938, -0.085702, -0.093522, -0.099237, -0.104020, -0.105939, -0.106226, -0.104298, -0.097541, -0.091253, -0.084969, -0.082450, -0.075561, -0.066547, -0.056511, -0.051248, -0.041287, -0.037794, -0.035633, -0.028059, -0.019518, -0.010556, -0.003388, 0.002054, 0.009492, 0.011478, 0.008555, 0.004735, -0.000781, -0.006427, -0.005697, -0.010270, -0.006112, -0.011704, -0.018717, -0.002750, -0.010971, 0.000116
	-0.076795, -0.064801, -0.080209, -0.085175, -0.093457, -0.101077, -0.104981, -0.106367, -0.106821, -0.105708, -0.098545, -0.090759, -0.086929, -0.083491, -0.074306, -0.064805, -0.055933, -0.049959, -0.042853, -0.036270, -0.034463, -0.029587, -0.018780, -0.010103, -0.003533, 0.001632, 0.007909, 0.014370, 0.009281, 0.004666, -0.002974, -0.007301, -0.010185, -0.008299, -0.006340, -0.009678, -0.011333, -0.010684, -0.006289, 0.002763
	-0.067470, -0.065770, -0.074038, -0.076420, -0.085702, -0.098704, -0.101940, -0.102629, -0.101903, -0.100342, -0.093820, -0.086941, -0.083804, -0.081020, -0.067700, -0.059395, -0.054055, -0.047911, -0.039687, -0.035672, -0.032029, -0.025979, -0.017057, -0.006973, -0.001656, 0.002001, 0.007249, 0.012112, 0.006541, 0.000572, -0.006284, -0.010415, -0.012279, -0.015087, -0.007848, -0.016491, -0.019704, -0.005357, -0.013151, 0.002966
	-0.074820, -0.054794, -0.069710, -0.075127, -0.082743, -0.091434, -0.095621, -0.097541, -0.099098, -0.097422, -0.089851, -0.083594, -0.081112, -0.078942, -0.066391, -0.057457, -0.050942, -0.048077, -0.041211, -0.034391, -0.030091, -0.026047, -0.014207, -0.005090, 0.000912, 0.005316, 0.010043, 0.015509, 0.011199, 0.004513, -0.001027, -0.006694, -0.011239, -0.011162, -0.009134, -0.013596, -0.014031, -0.011306, -0.007627, 0.001767
	-0.061695, -0.056074, -0.065188, -0.067950, -0.076218, -0.088303, -0.093436, -0.092999, -0.090937, -0.090555, -0.084407, -0.080354, -0.078692, -0.074308, -0.062767, -0.052729, -0.047475, -0.043949, -0.036669, -0.031720, -0.027940, -0.020058, -0.010125, -0.000940, 0.003512, 0.007720, 0.011869, 0.015296, 0.011180, 0.003886, -0.003309, -0.003380, -0.007926, -0.011633, -0.003540, -0.014182, -0.013975, -0.003720, -0.011797, 0.006338
	-0.070864, -0.046187, -0.061128, -0.065717, -0.072715, -0.083470, -0.088292, -0.087558, -0.087628, -0.089378, -0.083768, -0.077237, -0.077063, -0.071978, -0.061635, -0.052022, -0.046913, -0.041194, -0.034314, -0.028661, -0.027048, -0.021438, -0.009769, -0.001205, 0.004637, 0.008928, 0.013264, 0.017277, 0.013442, 0.007295, 0.003623, -0.002524, -0.004256, -0.005789, -0.004213, -0.007305, -0.010487, -0.010885, -0.006086, 0.007386
	-0.059345, -0.049207, -0.056858, -0.060052, -0.066579, -0.080604, -0.086910, -0.085647, -0.085267, -0.087618, -0.081260, -0.075368, -0.073937, -0.069758, -0.058235, -0.051634, -0.045288, -0.038732, -0.032262, -0.027928, -0.024928, -0.019266, -0.007996, 0.000923, 0.005834, 0.008336, 0.013557, 0.017068, 0.012350, 0.006475, 0.000982, 0.001103, -0.006223, -0.006853, -0.000966, -0.013148, -0.013975, -0.006310, -0.011605, 0.006165
	-0.066591, -0.039715, -0.053663, -0.059514, -0.065911, -0.075018, -0.080214, -0.082968, -0.083447, -0.085380, -0.079055, -0.071985, -0.070247, -0.065856, -0.057767, -0.049975, -0.044481, -0.039103, -0.031217, -0.024927, -0.020997, -0.016440, -0.004831, 0.004061, 0.009463, 0.011160, 0.014777, 0.020638, 0.017816, 0.011360, 0.006171, 0.002164, -0.002119, -0.003117, -0.003031, -0.005156, -0.011400, -0.011762, -0.009295, -0.000001
	-0.060314, -0.046160, -0.052794, -0.054967, -0.062049, -0.074106, -0.080446, -0.081200, -0.080809, -0.080477, -0.076170, -0.070932, -0.069101, -0.063634, -0.055720, -0.049501, -0.044939, -0.040131, -0.032438, -0.022882, -0.017627, -0.012524, -0.001324, 0.006685, 0.011868, 0.013658, 0.016095, 0.021837, 0.020158, 0.012528, 0.006089, 0.005453, -0.000976, -0.002140, 0.001104, -0.010111, -0.010612, -0.007452, -0.014357, 0.001011
	-0.075633, -0.036609, -0.049346, -0.055490, -0.059336, -0.067616, -0.073859, -0.075613, -0.076372, -0.078009, -0.070627, -0.064206, -0.064430, -0.061999, -0.054551, -0.047386, -0.040817, -0.037398, -0.028062, -0.018505, -0.012195, -0.007531, 0.001481, 0.011790, 0.019955, 0.022349, 0.022131, 0.024492, 0.023359, 0.019186, 0.014655, 0.008357, 0.004176, 0.002971, 0.002955, -0.000237, -0.005884, -0.010152, -0.009506, 0.002811
	-0.059008, -0.039658, -0.046978, -0.048324, -0.052285, -0.063338, -0.069082, -0.070556, -0.070625, -0.070049, -0.064460, -0.057403, -0.056723, -0.052882, -0.046968, -0.041507, -0.033211, -0.029974, -0.022900, -0.013579, -0.008803, -0.004962, 0.005653, 0.017026, 0.028171, 0.028651, 0.024731, 0.026850, 0.023371, 0.017073, 0.015171, 0.016616, 0.005521, 0.005756, 0.007586, -0.005103, -0.006856, -0.005604, -0.006599, 0.007528
	-0.068330, -0.030233, -0.043154, -0.047439, -0.047149, -0.051149, -0.060971, -0.063014, -0.065775, -0.064636, -0.058200, -0.050987, -0.050925, -0.050115, -0.041299, -0.033907, -0.026306, -0.024199, -0.017123, -0.009196, -0.006314, -0.003809, 0.004760, 0.015324, 0.026665, 0.029649, 0.028724, 0.027131, 0.025150, 0.021808, 0.019981, 0.016766, 0.012347, 0.008776, 0.005760, -0.000224, -0.004294, -0.005879, -0.002457, 0.010054
	-0.053519, -0.031388, -0.038255, -0.037590, -0.039245, -0.046335, -0.056314, -0.057830, -0.060291, -0.058967, -0.051413, -0.045449, -0.043947, -0.042018, -0.034113, -0.025887, -0.019539, -0.017727, -0.012711, -0.005860, -0.003102, 0.000774, 0.009438, 0.015884, 0.022961, 0.024229, 0.026012, 0.029407, 0.026717, 0.020406, 0.017796, 0.020289, 0.012243, 0.009711, 0.009234, -0.005990, -0.001013, 0.000740, -0.002144, 0.013012
	-0.068972, -0.023416, -0.032912, -0.036134, -0.035915, -0.040435, -0.047452, -0.051460, -0.055021, -0.055776, -0.048697, -0.039554, -0.036785, -0.035561, -0.029056, -0.021075, -0.013416, -0.012134, -0.007237, -0.000622, 0.001662, 0.005393, 0.012038, 0.019764, 0.023514, 0.026252, 0.028191, 0.031400, 0.031365, 0.027993, 0.023275, 0.021009, 0.018930, 0.014093, 0.009022, 0.004773, 0.002094, 0.001348, 0.005643, 0.015078
	-0.050527, -0.022437, -0.028090, -0.026206, -0.028387, -0.036911, -0.041310, -0.044227, -0.046970, -0.046769, -0.038081, -0.031386, -0.029516, -0.024050, -0.019435, -0.012381, -0.005732, -0.004173, 0.000911, 0.006849, 0.007360, 0.010699, 0.017436, 0.023369, 0.028527, 0.029640, 0.031002, 0.034727, 0.036582, 0.030763, 0.026015, 0.028623, 0.020834, 0.016185, 0.016933, 0.002829, 0.004984, 0.009818, 0.008874, 0.020032
	-0.067395, -0.010220, -0.021024, -0.024567, -0.024087, -0.029620, -0.032317, -0.034341, -0.038392, -0.038789, -0.030285, -0.021590, -0.017175, -0.014435, -0.007732, -0.000529, 0.005605, 0.007078, 0.012454, 0.017758, 0.016774, 0.015574, 0.020748, 0.028369, 0.033644, 0.034771, 0.036537, 0.040293, 0.042118, 0.039979, 0.035655, 0.033354, 0.030928, 0.024890, 0.021491, 0.018938, 0.013668, 0.012501, 0.017108, 0.023515
	-0.038833, -0.012802, -0.018564, -0.017459, -0.019062, -0.027068, -0.030119, -0.028336, -0.029665, -0.030695, -0.022239, -0.013522, -0.008358, -0.004785, 0.000463, 0.010662, 0.015564, 0.016950, 0.020281, 0.025300, 0.022680, 0.022717, 0.026679, 0.031617, 0.035801, 0.037098, 0.041294, 0.045640, 0.047879, 0.042000, 0.038044, 0.040629, 0.033892, 0.031247, 0.031584, 0.018500, 0.020116, 0.019823, 0.016638, 0.029979
	-0.054356, -0.002258, -0.012712, -0.017288, -0.016713, -0.022907, -0.024293, -0.021563, -0.022620, -0.021953, -0.015330, -0.005386, -0.000764, 0.002640, 0.009997, 0.022869, 0.028174, 0.027730, 0.030977, 0.035707, 0.032818, 0.030889, 0.033638, 0.038561, 0.044265, 0.045141, 0.047683, 0.051815, 0.054004, 0.050991, 0.045574, 0.043899, 0.044055, 0.039092, 0.035909, 0.032091, 0.026891, 0.022169, 0.024865, 0.030848
	-0.031827, -0.000102, -0.006368, -0.006487, -0.006247, -0.014001, -0.017110, -0.013043, -0.010851, -0.008764, -0.000213, 0.006477, 0.011144, 0.018309, 0.024745, 0.033643, 0.038648, 0.039249, 0.041148, 0.045266, 0.041693, 0.040999, 0.045484, 0.052613, 0.057066, 0.054753, 0.055112, 0.059287, 0.060203, 0.052465, 0.047993, 0.050999, 0.047464, 0.046460, 0.044507, 0.031433, 0.032267, 0.032025, 0.029852, 0.040329
	-0.053848, 0.008122, -0.005187, -0.009032, -0.006543, -0.010012, -0.013005, -0.011663, -0.008957, -0.004668, 0.005458, 0.012800, 0.016893, 0.023554, 0.031737, 0.038741, 0.043870, 0.043337, 0.046621, 0.047581, 0.045654, 0.044827, 0.050363, 0.058747, 0.061023, 0.060485, 0.059059, 0.061821, 0.061391, 0.055971, 0.051067, 0.050038, 0.051018, 0.046533, 0.043334, 0.042562, 0.036118, 0.029798, 0.032773, 0.039524
	-0.025830, 0.006164, -0.000655, 0.000164, 0.000088, -0.008033, -0.011008, -0.006017, -0.001301, 0.004088, 0.011848, 0.020276, 0.024465, 0.033383, 0.039126, 0.044268, 0.047916, 0.047402, 0.050050, 0.050456, 0.048891, 0.051771, 0.058154, 0.063246, 0.065463, 0.063072, 0.060950, 0.065351, 0.064614, 0.057455, 0.051194, 0.055723, 0.050906, 0.046407, 0.048283, 0.036561, 0.037400, 0.036887, 0.031589, 0.046759
	-0.041184, 0.017683, 0.006408, 0.000358, 0.001923, -0.002498, -0.003907, -0.001746, 0.001864, 0.006784, 0.017297, 0.026916, 0.030940, 0.036439, 0.045987, 0.050809, 0.054636, 0.052055, 0.053180, 0.056698, 0.057069, 0.055779, 0.063193, 0.067815, 0.071856, 0.070651, 0.067674, 0.070718, 0.070797, 0.062598, 0.057842, 0.056835, 0.056713, 0.051260, 0.048727, 0.048227, 0.044844, 0.039559, 0.041218, 0.044920
	-0.014008, 0.018619, 0.011274, 0.010878, 0.008771, 0.001246, -0.001819, 0.003600, 0.008052, 0.011983, 0.021970, 0.030757, 0.037662, 0.045972, 0.053195, 0.057661, 0.059206, 0.058383, 0.060240, 0.061039, 0.062504, 0.064497, 0.070278, 0.077704, 0.080246, 0.077015, 0.072985, 0.075685, 0.072584, 0.063534, 0.057732, 0.061938, 0.057545, 0.050931, 0.054863, 0.045820, 0.048882, 0.049675, 0.043484, 0.051538
	-0.045038, 0.028947, 0.019821, 0.012917, 0.013648, 0.007951, 0.005122, 0.007823, 0.012411, 0.015320, 0.025036, 0.036734, 0.045314, 0.052208, 0.062220, 0.065610, 0.068489, 0.066665, 0.068454, 0.069025, 0.071080, 0.073373, 0.079623, 0.085651, 0.088907, 0.088954, 0.084254, 0.084464, 0.080300, 0.072471, 0.067316, 0.066430, 0.065143, 0.057630, 0.058650, 0.059627, 0.057197, 0.054105, 0.055295, 0.057879
	-0.017117, 0.027364, 0.023067, 0.022758, 0.019246, 0.011825, 0.007962, 0.011522, 0.017237, 0.021779, 0.031329, 0.042642, 0.052349, 0.060322, 0.069568, 0.074657, 0.075211, 0.072882, 0.075373, 0.078391, 0.079512, 0.081816, 0.086101, 0.091730, 0.095061, 0.095682, 0.092100, 0.092873, 0.085769, 0.077219, 0.068392, 0.073179, 0.069972, 0.061240, 0.068306, 0.062227, 0.061008, 0.064520, 0.058543, 0.070728
	-0.042759, 0.035472, 0.029514, 0.023812, 0.024176, 0.020576, 0.017397, 0.018716, 0.022981, 0.027634, 0.041262, 0.050991, 0.058558, 0.067060, 0.077829, 0.083609, 0.084719, 0.082815, 0.085352, 0.087363, 0.091238, 0.091692, 0.096562, 0.102513, 0.106436, 0.108184, 0.105828, 0.107257, 0.102415, 0.090768, 0.084257, 0.081410, 0.081286, 0.073523, 0.074433, 0.076576, 0.070376, 0.068350, 0.071896, 0.072962
	-0.003143, 0.035517, 0.033266, 0.032727, 0.031843, 0.025862, 0.023177, 0.026936, 0.032953, 0.037457, 0.049289, 0.057429, 0.066625, 0.072540, 0.083814, 0.089321, 0.092420, 0.093053, 0.094752, 0.096876, 0.098364, 0.101271, 0.105185, 0.113505, 0.115784, 0.118957, 0.117138, 0.117934, 0.110930, 0.101497, 0.091051, 0.092731, 0.090574, 0.079282, 0.084691, 0.078426, 0.073451, 0.081698, 0.072811, 0.084352
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 19.8
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity
=======================
Extruder max_extrude_ratio=0.266081
Extruder max_extrude_ratio=0.266081
mcu 'mcu': Starting serial connect
webhooks client 3977449800: New connection
webhooks client 3977449800: Client info {'program': 'Moonraker', 'version': 'v0.9.3-0-g71f9e67'}
Loaded MCU 'mcu' 118 commands (v0.12.0-402-g2817b348 / gcc: (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027] binutils: (2.34-4+rpi1+14) 2.34)
MCU 'mcu' config: ADC_MAX=4095 BUS_PINS_i2c1_PB6_PB7=PB6,PB7 BUS_PINS_i2c1_PB8_PB9=PB8,PB9 BUS_PINS_i2c2_PB10_PB11=PB10,PB11 BUS_PINS_i2c3_PA8_PC9=PA8,PC9 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi2a=PC2,PC3,PB10 BUS_PINS_spi3a=PC11,PC12,PC10 BUS_PINS_spi4=PE13,PE14,PE12 BUS_PINS_spi5=PF8,PF9,PF7 BUS_PINS_spi5a=PH7,PF11,PH6 BUS_PINS_spi6=PG12,PG14,PG13 CLOCK_FREQ=400000000 MCU=stm32h723xx PWM_MAX=255 RESERVE_PINS_USB=PA11,PA12 RESERVE_PINS_crystal=PH0,PH1 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
mcu 'rpi': Starting connect
Loaded MCU 'rpi' 119 commands (?-20240727_132503-fv-az659-741 / gcc: (Raspbian 10.2.1-6+rpi1) 10.2.1 20210110 binutils: (GNU Binutils for Raspbian) 2.35.2)
MCU 'rpi' config: ADC_MAX=4095 CLOCK_FREQ=50000000 MCU=linux PCA9685_MAX=4096 PWM_MAX=32768 STATS_SUMSQ_BASE=256
mcu 'toolboard_t0': Starting serial connect
Loaded MCU 'toolboard_t0' 118 commands (v0.12.0-402-g2817b348 / gcc: (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027] binutils: (2.34-4+rpi1+14) 2.34)
MCU 'toolboard_t0' config: ADC_MAX=4095 BUS_PINS_i2c1_PA9_PA10=PA9,PA10 BUS_PINS_i2c1_PB6_PB7=PB6,PB7 BUS_PINS_i2c1_PB8_PB9=PB8,PB9 BUS_PINS_i2c2_PB10_PB11=PB10,PB11 BUS_PINS_i2c2_PB13_PB14=PB13,PB14 BUS_PINS_i2c3_PB3_PB4=PB3,PB4 BUS_PINS_i2c3_PC0_PC1=PC0,PC1 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi2_PB2_PB11_PB10=PB2,PB11,PB10 BUS_PINS_spi2a=PC2,PC3,PB10 BUS_PINS_spi3=PB4,PB5,PB3 CLOCK_FREQ=64000000 MCU=stm32g0b1xx PWM_MAX=255 RESERVE_PINS_USB=PA11,PA12 RESERVE_PINS_crystal=PF0,PF1 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
mcu 'toolboard_t1': Starting serial connect
Loaded MCU 'toolboard_t1' 118 commands (v0.12.0-402-g2817b348 / gcc: (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027] binutils: (2.34-4+rpi1+14) 2.34)
MCU 'toolboard_t1' config: ADC_MAX=4095 BUS_PINS_i2c1_PA9_PA10=PA9,PA10 BUS_PINS_i2c1_PB6_PB7=PB6,PB7 BUS_PINS_i2c1_PB8_PB9=PB8,PB9 BUS_PINS_i2c2_PB10_PB11=PB10,PB11 BUS_PINS_i2c2_PB13_PB14=PB13,PB14 BUS_PINS_i2c3_PB3_PB4=PB3,PB4 BUS_PINS_i2c3_PC0_PC1=PC0,PC1 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi2_PB2_PB11_PB10=PB2,PB11,PB10 BUS_PINS_spi2a=PC2,PC3,PB10 BUS_PINS_spi3=PB4,PB5,PB3 CLOCK_FREQ=64000000 MCU=stm32g0b1xx PWM_MAX=255 RESERVE_PINS_USB=PA11,PA12 RESERVE_PINS_crystal=PF0,PF1 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
mcu 'dinghy': Starting serial connect
Loaded MCU 'dinghy' 118 commands (v0.12.0-402-g2817b348 / gcc: (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027] binutils: (2.34-4+rpi1+14) 2.34)
MCU 'dinghy' config: ADC_MAX=4095 BUS_PINS_i2c1=PB6,PB7 BUS_PINS_i2c1_PB6_PB7=PB6,PB7 BUS_PINS_i2c1_PB8_PB7=PB8,PB7 BUS_PINS_i2c1_PB8_PB9=PB8,PB9 BUS_PINS_i2c1_PF1_PF0=PF1,PF0 BUS_PINS_i2c1a=PF1,PF0 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi2a=PC2,PC3,PB10 CLOCK_FREQ=48000000 MCU=stm32f072xb PWM_MAX=255 RESERVE_PINS_USB=PA11,PA12 RESERVE_PINS_crystal=PF0,PF1 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
mcu 'plasma': Starting serial connect
mcu 'plasma': Timeout on connect
mcu 'plasma': Wait for identify_response
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/serialhdl.py", line 68, in _get_identify_data
    params = self.send_with_response(msg, 'identify_response')
  File "/home/pi/klipper/klippy/serialhdl.py", line 262, in send_with_response
    return src.get_response([cmd], self.default_cmd_queue)
  File "/home/pi/klipper/klippy/serialhdl.py", line 319, in get_response
    self.serial.raw_send_wait_ack(cmds[-1], minclock, reqclock,
  File "/home/pi/klipper/klippy/serialhdl.py", line 254, in raw_send_wait_ack
    self._error("Serial connection closed")
  File "/home/pi/klipper/klippy/serialhdl.py", line 61, in _error
    raise error(self.warn_prefix + (msg % params))
serialhdl.error: mcu 'plasma': Serial connection closed
Loaded MCU 'plasma' 118 commands (v0.12.0-402-g2817b348 / gcc: (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027] binutils: (2.34-4+rpi1+14) 2.34)
MCU 'plasma' config: ADC_MAX=4095 BUS_PINS_i2c0a=gpio0,gpio1 BUS_PINS_i2c0b=gpio4,gpio5 BUS_PINS_i2c0c=gpio8,gpio9 BUS_PINS_i2c0d=gpio12,gpio13 BUS_PINS_i2c0e=gpio16,gpio17 BUS_PINS_i2c0f=gpio20,gpio21 BUS_PINS_i2c0g=gpio24,gpio25 BUS_PINS_i2c0h=gpio28,gpio29 BUS_PINS_i2c1a=gpio2,gpio3 BUS_PINS_i2c1b=gpio6,gpio7 BUS_PINS_i2c1c=gpio10,gpio11 BUS_PINS_i2c1d=gpio14,gpio15 BUS_PINS_i2c1e=gpio18,gpio19 BUS_PINS_i2c1f=gpio22,gpio23 BUS_PINS_i2c1g=gpio26,gpio27 BUS_PINS_spi0_gpio0_gpio3_gpio2=gpio0,gpio3,gpio2 BUS_PINS_spi0_gpio16_gpio19_gpio18=gpio16,gpio19,gpio18 BUS_PINS_spi0_gpio20_gpio23_gpio22=gpio20,gpio23,gpio22 BUS_PINS_spi0_gpio4_gpio3_gpio2=gpio4,gpio3,gpio2 BUS_PINS_spi0_gpio4_gpio7_gpio6=gpio4,gpio7,gpio6 BUS_PINS_spi0a=gpio0,gpio3,gpio2 BUS_PINS_spi0b=gpio4,gpio7,gpio6 BUS_PINS_spi0c=gpio16,gpio19,gpio18 BUS_PINS_spi0d=gpio20,gpio23,gpio22 BUS_PINS_spi1_gpio12_gpio15_gpio14=gpio12,gpio15,gpio14 BUS_PINS_spi1_gpio24_gpio27_gpio26=gpio24,gpio27,gpio26 BUS_PINS_spi1_gpio8_gpio11_gpio10=gpio8,gpio11,gpio10 BUS_PINS_spi1a=gpio8,gpio11,gpio10 BUS_PINS_spi1b=gpio12,gpio15,gpio14 BUS_PINS_spi1c=gpio24,gpio27,gpio26 CLOCK_FREQ=12000000 MCU=rp2040 PWM_MAX=255 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
mcu_temperature 'mcu' nominal base=-263.822394 slope=1581.081081
mcu_temperature 'toolboard_t0' nominal base=-262.550143 slope=1290.687679
mcu_temperature 'toolboard_t1' nominal base=-272.332362 slope=1313.265306
mcu 'beacon': Starting serial connect
Loaded MCU 'beacon' 45 commands (Beacon 2.1.0 / )
MCU 'beacon' config: ADC_MAX=4095 BEACON_ACCEL_BITS=12 BEACON_ACCEL_SCALE_16G=7.81 BEACON_ACCEL_SCALE_2G=0.98 BEACON_ACCEL_SCALE_4G=1.95 BEACON_ACCEL_SCALE_8G=3.91 BEACON_ADC_SMOOTH_COUNT=16 BEACON_HAS_ACCEL=1 BEACON_REV=H CLOCK_FREQ=32000000 MCU=beacon STATS_SUMSQ_BASE=256
Sending MCU 'mcu' printer configuration...
Configured MCU 'mcu' (1024 moves)
Sending MCU 'rpi' printer configuration...
Configured MCU 'rpi' (1024 moves)
Sending MCU 'toolboard_t0' printer configuration...
Configured MCU 'toolboard_t0' (1024 moves)
Sending MCU 'toolboard_t1' printer configuration...
Configured MCU 'toolboard_t1' (1024 moves)
Sending MCU 'dinghy' printer configuration...
Configured MCU 'dinghy' (1024 moves)
Sending MCU 'plasma' printer configuration...
Configured MCU 'plasma' (1024 moves)
Starting heater checks for heater_bed
beacon: loaded fnorm=5106174.70 temp=18.98 amfg=1.012 from nvm
beacon: built tempco model version 1 {'amfg': 1.0116254092446901, 'tcc': -7.155348984545153e-06, 'tcfl': -0.0006342204102343939, 'tctl': 0.001940863247628072, 'fmin': 5106174.703687429, 'fmin_temp': 18.98276710510254}
Enabling Beacon accelerometer
Selected Beacon accelerometer scale 16g
Sending MCU 'beacon' printer configuration...
Configured MCU 'beacon' (0 moves)
beacon_user_z_offset: beacon_contact_start_print_true_zero is enabled, activating beacon user z-offset management. Applying configured z_offset of 0.0 mm to named offset 'user_probe_z_offset'.
Starting heater checks for extruder
Starting heater checks for extruder1
Write g-code response
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/gcode.py", line 459, in _respond_raw
    os.write(self.fd, (msg+"\n").encode())
BlockingIOError: [Errno 11] Resource temporarily unavailable
Stats 8863.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4514 bytes_read=7812 bytes_retransmit=9 bytes_invalid=0 send_seq=332 receive_seq=332 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016067 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=922 bytes_read=4835 bytes_retransmit=0 bytes_invalid=0 send_seq=125 receive_seq=125 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999339 adj=49995084 toolboard_t0: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000007 bytes_write=1468 bytes_read=5124 bytes_retransmit=9 bytes_invalid=0 send_seq=160 receive_seq=160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63996031 toolboard_t1: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000007 bytes_write=1457 bytes_read=5103 bytes_retransmit=9 bytes_invalid=0 send_seq=158 receive_seq=158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000139 adj=63996065 dinghy: mcu_awake=0.010 mcu_task_avg=0.000030 mcu_task_stddev=0.000030 bytes_write=1053 bytes_read=4548 bytes_retransmit=9 bytes_invalid=0 send_seq=129 receive_seq=129 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999717 adj=47996865 plasma: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1682 bytes_read=4738 bytes_retransmit=9 bytes_invalid=0 send_seq=133 receive_seq=133 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999927 adj=11999620 Octopus_Pro_H723_V1.1: temp=0.0 EBB42_Gen2_v1.0_T0: temp=0.0 EBB42_Gen2_v1.0_T1: temp=0.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=0.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=369 bytes_read=1981 bytes_retransmit=0 bytes_invalid=0 send_seq=60 receive_seq=60 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31998458 adj=31996791 coil_temp=16.9 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=0.0 th1: temp=0.0 th2: temp=0.0 th3: temp=0.0 sysload=0.57 cputime=643.031 memavail=7397184 print_time=17.774 buffer_time=0.262 print_stall=0 extruder: target=0 temp=0.0 pwm=0.000 extruder1: target=0 temp=0.0 pwm=0.000
Initializing RatOS...
CALCULATE_PRINTABLE_AREA: Printable area calculated: X: 0,500.0 Y: 0,500.0
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Extruder extruder already active
Extruder 'extruder' now syncing with 'extruder'
Extruder 'extruder1' now syncing with 'extruder1'
shaper_type_x:mzv shaper_freq_x:54.200 damping_ratio_x:0.100000
shaper_type_y:2hump_ei shaper_freq_y:45.000 damping_ratio_y:0.100000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
ratos: beacon probing regions updated: BeaconProbingRegions(x_offset=0.0, y_offset=27.5, printable_x_max=500.0, printable_y_max=500.0, mesh_proximity_min_coil_pos=(20.0, 20.0), mesh_proximity_max_coil_pos=(480.0, 480.0), mesh_proximity_min_toolhead_pos=(20.0, -7.5), mesh_proximity_max_toolhead_pos=(480.0, 452.5), mesh_contact_min=(20.0, 20.0), mesh_contact_max=(480.0, 480.0), logical_proximity_min_coil_pos=(20.0, 20.0), logical_proximity_max_coil_pos=(480.0, 480.0), logical_proximity_min_toolhead_pos=(20.0, -7.5), logical_proximity_max_toolhead_pos=(480.0, 452.5), logical_contact_min=(10.0, -17.5), logical_contact_max=(490.0, 462.5))
webhooks: registering remote method 'shutdown_machine' for connection id: 3977449800
webhooks: registering remote method 'reboot_machine' for connection id: 3977449800
webhooks: registering remote method 'pause_job_queue' for connection id: 3977449800
webhooks: registering remote method 'start_job_queue' for connection id: 3977449800
Stats 8864.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4520 bytes_read=7857 bytes_retransmit=9 bytes_invalid=0 send_seq=333 receive_seq=333 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016138 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=928 bytes_read=4851 bytes_retransmit=0 bytes_invalid=0 send_seq=126 receive_seq=126 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999438 adj=50002719 toolboard_t0: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000007 bytes_write=1474 bytes_read=5196 bytes_retransmit=9 bytes_invalid=0 send_seq=161 receive_seq=161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=64001160 toolboard_t1: mcu_awake=0.001 mcu_task_avg=0.000012 mcu_task_stddev=0.000007 bytes_write=1463 bytes_read=5175 bytes_retransmit=9 bytes_invalid=0 send_seq=159 receive_seq=159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000109 adj=64000528 dinghy: mcu_awake=0.010 mcu_task_avg=0.000030 mcu_task_stddev=0.000030 bytes_write=1059 bytes_read=4720 bytes_retransmit=9 bytes_invalid=0 send_seq=130 receive_seq=130 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999677 adj=47999356 plasma: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1688 bytes_read=4754 bytes_retransmit=9 bytes_invalid=0 send_seq=134 receive_seq=134 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999943 adj=11999360 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=375 bytes_read=2337 bytes_retransmit=0 bytes_invalid=0 send_seq=61 receive_seq=61 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999269 adj=31997264 coil_temp=16.9 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=51.3 th1: temp=51.5 th2: temp=57.2 th3: temp=55.6 sysload=0.57 cputime=643.246 memavail=7399136 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
HELLO_RATOS: version: v2.1.0-0-g0be29e9d, distro: RatOS v2.1.0-RC4 (bullseye)
No deferred RatOS console messages to write.
ratos: Current CPU governor(s): performance
Stats 8866.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4532 bytes_read=8063 bytes_retransmit=9 bytes_invalid=0 send_seq=335 receive_seq=335 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016170 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=934 bytes_read=4867 bytes_retransmit=0 bytes_invalid=0 send_seq=127 receive_seq=127 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999454 adj=50002032 toolboard_t0: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000031 bytes_write=1486 bytes_read=5383 bytes_retransmit=9 bytes_invalid=0 send_seq=163 receive_seq=163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000244 adj=64000518 toolboard_t1: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000031 bytes_write=1475 bytes_read=5362 bytes_retransmit=9 bytes_invalid=0 send_seq=161 receive_seq=161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000118 adj=63999842 dinghy: mcu_awake=0.005 mcu_task_avg=0.000026 mcu_task_stddev=0.000055 bytes_write=1065 bytes_read=5123 bytes_retransmit=9 bytes_invalid=0 send_seq=131 receive_seq=131 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999687 adj=47998916 plasma: mcu_awake=0.010 mcu_task_avg=0.000023 mcu_task_stddev=0.000282 bytes_write=1694 bytes_read=4785 bytes_retransmit=9 bytes_invalid=0 send_seq=135 receive_seq=135 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999973 adj=11999394 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=387 bytes_read=2897 bytes_retransmit=0 bytes_invalid=0 send_seq=63 receive_seq=63 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999708 adj=31998460 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=51.2 th1: temp=51.5 th2: temp=57.1 th3: temp=55.5 sysload=0.57 cputime=643.533 memavail=7396120 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 8867.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000006 mcu_task_stddev=0.000011 bytes_write=4538 bytes_read=8181 bytes_retransmit=9 bytes_invalid=0 send_seq=336 receive_seq=336 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016110 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000021 bytes_write=940 bytes_read=4896 bytes_retransmit=0 bytes_invalid=0 send_seq=128 receive_seq=128 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999400 adj=50000258 toolboard_t0: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000031 bytes_write=1492 bytes_read=5511 bytes_retransmit=9 bytes_invalid=0 send_seq=164 receive_seq=164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63999435 toolboard_t1: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000031 bytes_write=1481 bytes_read=5490 bytes_retransmit=9 bytes_invalid=0 send_seq=162 receive_seq=162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000128 adj=63998945 dinghy: mcu_awake=0.005 mcu_task_avg=0.000026 mcu_task_stddev=0.000055 bytes_write=1071 bytes_read=5415 bytes_retransmit=9 bytes_invalid=0 send_seq=132 receive_seq=132 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999649 adj=47998471 plasma: mcu_awake=0.010 mcu_task_avg=0.000023 mcu_task_stddev=0.000282 bytes_write=1700 bytes_read=4801 bytes_retransmit=9 bytes_invalid=0 send_seq=136 receive_seq=136 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999983 adj=11999478 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=393 bytes_read=3253 bytes_retransmit=0 bytes_invalid=0 send_seq=64 receive_seq=64 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999714 adj=31999098 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=51.1 th1: temp=51.5 th2: temp=57.0 th3: temp=55.4 sysload=0.53 cputime=643.715 memavail=7392320 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8868.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000006 mcu_task_stddev=0.000011 bytes_write=4544 bytes_read=8280 bytes_retransmit=9 bytes_invalid=0 send_seq=337 receive_seq=337 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016049 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000021 bytes_write=946 bytes_read=4912 bytes_retransmit=0 bytes_invalid=0 send_seq=129 receive_seq=129 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999402 adj=49999364 toolboard_t0: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000031 bytes_write=1498 bytes_read=5611 bytes_retransmit=9 bytes_invalid=0 send_seq=165 receive_seq=165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63998983 toolboard_t1: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000031 bytes_write=1487 bytes_read=5590 bytes_retransmit=9 bytes_invalid=0 send_seq=163 receive_seq=163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000123 adj=63998667 dinghy: mcu_awake=0.005 mcu_task_avg=0.000026 mcu_task_stddev=0.000055 bytes_write=1077 bytes_read=5647 bytes_retransmit=9 bytes_invalid=0 send_seq=133 receive_seq=133 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999634 adj=47998196 plasma: mcu_awake=0.010 mcu_task_avg=0.000023 mcu_task_stddev=0.000282 bytes_write=1712 bytes_read=4833 bytes_retransmit=9 bytes_invalid=0 send_seq=138 receive_seq=138 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999958 adj=11999512 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=399 bytes_read=3609 bytes_retransmit=0 bytes_invalid=0 send_seq=65 receive_seq=65 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999773 adj=31998959 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=51.0 th1: temp=51.4 th2: temp=56.8 th3: temp=55.3 sysload=0.53 cputime=643.752 memavail=7399044 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8869.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000006 mcu_task_stddev=0.000011 bytes_write=4550 bytes_read=8412 bytes_retransmit=9 bytes_invalid=0 send_seq=338 receive_seq=338 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016041 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000021 bytes_write=952 bytes_read=4928 bytes_retransmit=0 bytes_invalid=0 send_seq=130 receive_seq=130 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999362 adj=49998912 toolboard_t0: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000031 bytes_write=1504 bytes_read=5711 bytes_retransmit=9 bytes_invalid=0 send_seq=166 receive_seq=166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000217 adj=63998667 toolboard_t1: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000031 bytes_write=1493 bytes_read=5690 bytes_retransmit=9 bytes_invalid=0 send_seq=164 receive_seq=164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000106 adj=63998409 dinghy: mcu_awake=0.005 mcu_task_avg=0.000026 mcu_task_stddev=0.000055 bytes_write=1083 bytes_read=5879 bytes_retransmit=9 bytes_invalid=0 send_seq=134 receive_seq=134 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999605 adj=47998049 plasma: mcu_awake=0.010 mcu_task_avg=0.000023 mcu_task_stddev=0.000282 bytes_write=1718 bytes_read=4849 bytes_retransmit=9 bytes_invalid=0 send_seq=139 receive_seq=139 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999942 adj=11999453 Octopus_Pro_H723_V1.1: temp=29.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=405 bytes_read=3965 bytes_retransmit=0 bytes_invalid=0 send_seq=66 receive_seq=66 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999795 adj=31998987 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=51.1 th1: temp=51.3 th2: temp=56.7 th3: temp=55.2 sysload=0.53 cputime=643.784 memavail=7398792 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 8870.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000006 mcu_task_stddev=0.000011 bytes_write=4556 bytes_read=8515 bytes_retransmit=9 bytes_invalid=0 send_seq=339 receive_seq=339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015990 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000021 bytes_write=958 bytes_read=4944 bytes_retransmit=0 bytes_invalid=0 send_seq=131 receive_seq=131 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999344 adj=49998356 toolboard_t0: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000031 bytes_write=1510 bytes_read=5839 bytes_retransmit=9 bytes_invalid=0 send_seq=167 receive_seq=167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63998386 toolboard_t1: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000031 bytes_write=1499 bytes_read=5818 bytes_retransmit=9 bytes_invalid=0 send_seq=165 receive_seq=165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000099 adj=63998131 dinghy: mcu_awake=0.005 mcu_task_avg=0.000026 mcu_task_stddev=0.000055 bytes_write=1089 bytes_read=6171 bytes_retransmit=9 bytes_invalid=0 send_seq=135 receive_seq=135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999593 adj=47997853 plasma: mcu_awake=0.010 mcu_task_avg=0.000023 mcu_task_stddev=0.000282 bytes_write=1724 bytes_read=4865 bytes_retransmit=9 bytes_invalid=0 send_seq=140 receive_seq=140 retransmit_seq=2 srtt=0.000 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999943 adj=11999416 Octopus_Pro_H723_V1.1: temp=29.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=411 bytes_read=4321 bytes_retransmit=0 bytes_invalid=0 send_seq=67 receive_seq=67 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999816 adj=31998923 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=50.9 th1: temp=51.2 th2: temp=56.6 th3: temp=55.1 sysload=0.53 cputime=643.817 memavail=7400996 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 8871.5: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000006 mcu_task_stddev=0.000011 bytes_write=4562 bytes_read=8618 bytes_retransmit=9 bytes_invalid=0 send_seq=340 receive_seq=340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015967 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000021 bytes_write=964 bytes_read=4960 bytes_retransmit=0 bytes_invalid=0 send_seq=132 receive_seq=132 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999329 adj=49998055 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1516 bytes_read=5953 bytes_retransmit=9 bytes_invalid=0 send_seq=168 receive_seq=168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63998187 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1505 bytes_read=5932 bytes_retransmit=9 bytes_invalid=0 send_seq=166 receive_seq=166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000089 adj=63997993 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1095 bytes_read=6418 bytes_retransmit=9 bytes_invalid=0 send_seq=136 receive_seq=136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999580 adj=47997787 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1730 bytes_read=4892 bytes_retransmit=9 bytes_invalid=0 send_seq=141 receive_seq=141 retransmit_seq=2 srtt=0.000 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999934 adj=11999439 Octopus_Pro_H723_V1.1: temp=29.9 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=417 bytes_read=4677 bytes_retransmit=0 bytes_invalid=0 send_seq=68 receive_seq=68 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999823 adj=31998898 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=50.9 th1: temp=51.2 th2: temp=56.5 th3: temp=55.0 sysload=0.53 cputime=643.849 memavail=7400844 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 8872.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4568 bytes_read=8764 bytes_retransmit=9 bytes_invalid=0 send_seq=341 receive_seq=341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015949 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=970 bytes_read=4989 bytes_retransmit=0 bytes_invalid=0 send_seq=133 receive_seq=133 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999317 adj=49997817 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1522 bytes_read=6053 bytes_retransmit=9 bytes_invalid=0 send_seq=169 receive_seq=169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63998081 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1511 bytes_read=6032 bytes_retransmit=9 bytes_invalid=0 send_seq=167 receive_seq=167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997850 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1101 bytes_read=6650 bytes_retransmit=9 bytes_invalid=0 send_seq=137 receive_seq=137 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999577 adj=47997716 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1736 bytes_read=4908 bytes_retransmit=9 bytes_invalid=0 send_seq=142 receive_seq=142 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999928 adj=11999420 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=423 bytes_read=5033 bytes_retransmit=0 bytes_invalid=0 send_seq=69 receive_seq=69 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999859 adj=31998919 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=50.8 th1: temp=51.2 th2: temp=56.4 th3: temp=55.0 sysload=0.48 cputime=643.881 memavail=7400844 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 8873.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4574 bytes_read=8867 bytes_retransmit=9 bytes_invalid=0 send_seq=342 receive_seq=342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015927 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=976 bytes_read=5005 bytes_retransmit=0 bytes_invalid=0 send_seq=134 receive_seq=134 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999299 adj=49997648 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1528 bytes_read=6181 bytes_retransmit=9 bytes_invalid=0 send_seq=170 receive_seq=170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997974 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1517 bytes_read=6160 bytes_retransmit=9 bytes_invalid=0 send_seq=168 receive_seq=168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997701 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1107 bytes_read=6942 bytes_retransmit=9 bytes_invalid=0 send_seq=138 receive_seq=138 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999567 adj=47997697 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1742 bytes_read=4924 bytes_retransmit=9 bytes_invalid=0 send_seq=143 receive_seq=143 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999929 adj=11999412 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=429 bytes_read=5389 bytes_retransmit=0 bytes_invalid=0 send_seq=70 receive_seq=70 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999863 adj=31998952 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=50.8 th1: temp=51.0 th2: temp=56.3 th3: temp=54.8 sysload=0.48 cputime=643.913 memavail=7400844 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8874.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4580 bytes_read=8970 bytes_retransmit=9 bytes_invalid=0 send_seq=343 receive_seq=343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015922 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=982 bytes_read=5021 bytes_retransmit=0 bytes_invalid=0 send_seq=135 receive_seq=135 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999297 adj=49997486 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1534 bytes_read=6281 bytes_retransmit=9 bytes_invalid=0 send_seq=171 receive_seq=171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000199 adj=63997929 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1523 bytes_read=6260 bytes_retransmit=9 bytes_invalid=0 send_seq=169 receive_seq=169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000041 adj=63997588 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1113 bytes_read=7174 bytes_retransmit=9 bytes_invalid=0 send_seq=139 receive_seq=139 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999569 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1748 bytes_read=4940 bytes_retransmit=9 bytes_invalid=0 send_seq=144 receive_seq=144 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999926 adj=11999426 Octopus_Pro_H723_V1.1: temp=30.0 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=435 bytes_read=5745 bytes_retransmit=0 bytes_invalid=0 send_seq=71 receive_seq=71 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999868 adj=31998884 coil_temp=16.9 refs=0 mcu_temp=20.34 supply_voltage=3.011 th0: temp=50.8 th1: temp=51.0 th2: temp=56.2 th3: temp=54.8 sysload=0.48 cputime=643.945 memavail=7400616 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 8875.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4586 bytes_read=9102 bytes_retransmit=9 bytes_invalid=0 send_seq=344 receive_seq=344 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015916 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=988 bytes_read=5037 bytes_retransmit=0 bytes_invalid=0 send_seq=136 receive_seq=136 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999304 adj=49997432 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1540 bytes_read=6381 bytes_retransmit=9 bytes_invalid=0 send_seq=172 receive_seq=172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000198 adj=63997818 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1529 bytes_read=6360 bytes_retransmit=9 bytes_invalid=0 send_seq=170 receive_seq=170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000034 adj=63997506 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1125 bytes_read=7422 bytes_retransmit=9 bytes_invalid=0 send_seq=141 receive_seq=141 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999562 adj=47997669 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1754 bytes_read=4956 bytes_retransmit=9 bytes_invalid=0 send_seq=145 receive_seq=145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999923 adj=11999422 Octopus_Pro_H723_V1.1: temp=30.1 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=441 bytes_read=6101 bytes_retransmit=0 bytes_invalid=0 send_seq=72 receive_seq=72 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999872 adj=31998830 coil_temp=16.9 refs=0 mcu_temp=20.34 supply_voltage=3.011 th0: temp=50.7 th1: temp=51.0 th2: temp=56.1 th3: temp=54.7 sysload=0.48 cputime=643.977 memavail=7400616 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8876.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4592 bytes_read=9205 bytes_retransmit=9 bytes_invalid=0 send_seq=345 receive_seq=345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015909 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=994 bytes_read=5053 bytes_retransmit=0 bytes_invalid=0 send_seq=137 receive_seq=137 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999309 adj=49997446 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1546 bytes_read=6523 bytes_retransmit=9 bytes_invalid=0 send_seq=173 receive_seq=173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000200 adj=63997775 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1535 bytes_read=6502 bytes_retransmit=9 bytes_invalid=0 send_seq=171 receive_seq=171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997469 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1131 bytes_read=7729 bytes_retransmit=9 bytes_invalid=0 send_seq=142 receive_seq=142 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1760 bytes_read=4983 bytes_retransmit=9 bytes_invalid=0 send_seq=146 receive_seq=146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999924 adj=11999419 Octopus_Pro_H723_V1.1: temp=30.1 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=447 bytes_read=6457 bytes_retransmit=0 bytes_invalid=0 send_seq=73 receive_seq=73 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999880 adj=31998790 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.011 th0: temp=50.7 th1: temp=50.9 th2: temp=56.0 th3: temp=54.7 sysload=0.48 cputime=644.013 memavail=7399852 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8877.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4598 bytes_read=9322 bytes_retransmit=9 bytes_invalid=0 send_seq=346 receive_seq=346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015942 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1006 bytes_read=5098 bytes_retransmit=0 bytes_invalid=0 send_seq=139 receive_seq=139 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999305 adj=49997448 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1552 bytes_read=6623 bytes_retransmit=9 bytes_invalid=0 send_seq=174 receive_seq=174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997765 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1541 bytes_read=6602 bytes_retransmit=9 bytes_invalid=0 send_seq=172 receive_seq=172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997498 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1137 bytes_read=7961 bytes_retransmit=9 bytes_invalid=0 send_seq=143 receive_seq=143 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1766 bytes_read=4999 bytes_retransmit=9 bytes_invalid=0 send_seq=147 receive_seq=147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999924 adj=11999432 Octopus_Pro_H723_V1.1: temp=30.2 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=453 bytes_read=6813 bytes_retransmit=0 bytes_invalid=0 send_seq=74 receive_seq=74 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999883 adj=31998777 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.011 th0: temp=50.6 th1: temp=50.8 th2: temp=56.0 th3: temp=54.6 sysload=0.52 cputime=644.046 memavail=7399748 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 8878.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4604 bytes_read=9451 bytes_retransmit=9 bytes_invalid=0 send_seq=347 receive_seq=347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015935 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1012 bytes_read=5114 bytes_retransmit=0 bytes_invalid=0 send_seq=140 receive_seq=140 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999294 adj=49997366 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1558 bytes_read=6723 bytes_retransmit=9 bytes_invalid=0 send_seq=175 receive_seq=175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63997679 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1547 bytes_read=6702 bytes_retransmit=9 bytes_invalid=0 send_seq=173 receive_seq=173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000026 adj=63997434 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1143 bytes_read=8193 bytes_retransmit=9 bytes_invalid=0 send_seq=144 receive_seq=144 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997612 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1772 bytes_read=5015 bytes_retransmit=9 bytes_invalid=0 send_seq=148 receive_seq=148 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999923 adj=11999432 Octopus_Pro_H723_V1.1: temp=30.2 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=459 bytes_read=7169 bytes_retransmit=0 bytes_invalid=0 send_seq=75 receive_seq=75 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999898 adj=31998734 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.011 th0: temp=50.6 th1: temp=50.8 th2: temp=55.9 th3: temp=54.6 sysload=0.52 cputime=644.078 memavail=7399292 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8879.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4610 bytes_read=9552 bytes_retransmit=9 bytes_invalid=0 send_seq=348 receive_seq=348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015936 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1018 bytes_read=5130 bytes_retransmit=0 bytes_invalid=0 send_seq=141 receive_seq=141 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999285 adj=49997292 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1564 bytes_read=6851 bytes_retransmit=9 bytes_invalid=0 send_seq=176 receive_seq=176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997651 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1553 bytes_read=6830 bytes_retransmit=9 bytes_invalid=0 send_seq=174 receive_seq=174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997418 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1149 bytes_read=8485 bytes_retransmit=9 bytes_invalid=0 send_seq=145 receive_seq=145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997594 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1778 bytes_read=5031 bytes_retransmit=9 bytes_invalid=0 send_seq=149 receive_seq=149 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999430 Octopus_Pro_H723_V1.1: temp=30.1 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=465 bytes_read=7525 bytes_retransmit=0 bytes_invalid=0 send_seq=76 receive_seq=76 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999893 adj=31998777 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=50.5 th1: temp=50.8 th2: temp=55.8 th3: temp=54.4 sysload=0.52 cputime=644.111 memavail=7399292 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 8880.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4616 bytes_read=9655 bytes_retransmit=9 bytes_invalid=0 send_seq=349 receive_seq=349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015922 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1024 bytes_read=5146 bytes_retransmit=0 bytes_invalid=0 send_seq=142 receive_seq=142 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999282 adj=49997233 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1570 bytes_read=6951 bytes_retransmit=9 bytes_invalid=0 send_seq=177 receive_seq=177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997631 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1559 bytes_read=6930 bytes_retransmit=9 bytes_invalid=0 send_seq=175 receive_seq=175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000020 adj=63997412 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1155 bytes_read=8717 bytes_retransmit=9 bytes_invalid=0 send_seq=146 receive_seq=146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997585 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1784 bytes_read=5047 bytes_retransmit=9 bytes_invalid=0 send_seq=150 receive_seq=150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999427 Octopus_Pro_H723_V1.1: temp=30.1 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=471 bytes_read=7881 bytes_retransmit=0 bytes_invalid=0 send_seq=77 receive_seq=77 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999894 adj=31998714 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=50.4 th1: temp=50.7 th2: temp=55.7 th3: temp=54.4 sysload=0.52 cputime=644.142 memavail=7399292 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 8881.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4622 bytes_read=9787 bytes_retransmit=9 bytes_invalid=0 send_seq=350 receive_seq=350 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015910 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1030 bytes_read=5162 bytes_retransmit=0 bytes_invalid=0 send_seq=143 receive_seq=143 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999278 adj=49997242 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1576 bytes_read=7065 bytes_retransmit=9 bytes_invalid=0 send_seq=178 receive_seq=178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997668 toolboard_t1: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1565 bytes_read=7030 bytes_retransmit=9 bytes_invalid=0 send_seq=176 receive_seq=176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000019 adj=63997423 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1161 bytes_read=8964 bytes_retransmit=9 bytes_invalid=0 send_seq=147 receive_seq=147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997602 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1790 bytes_read=5074 bytes_retransmit=9 bytes_invalid=0 send_seq=151 receive_seq=151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999435 Octopus_Pro_H723_V1.1: temp=30.1 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=477 bytes_read=8237 bytes_retransmit=0 bytes_invalid=0 send_seq=78 receive_seq=78 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999896 adj=31998702 coil_temp=16.9 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=50.4 th1: temp=50.6 th2: temp=55.6 th3: temp=54.3 sysload=0.52 cputime=644.174 memavail=7399292 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8882.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4628 bytes_read=9904 bytes_retransmit=9 bytes_invalid=0 send_seq=351 receive_seq=351 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015900 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1036 bytes_read=5178 bytes_retransmit=0 bytes_invalid=0 send_seq=144 receive_seq=144 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999278 adj=49997239 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1582 bytes_read=7193 bytes_retransmit=9 bytes_invalid=0 send_seq=179 receive_seq=179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000192 adj=63997693 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1571 bytes_read=7172 bytes_retransmit=9 bytes_invalid=0 send_seq=177 receive_seq=177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997447 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1167 bytes_read=9256 bytes_retransmit=9 bytes_invalid=0 send_seq=148 receive_seq=148 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1796 bytes_read=5090 bytes_retransmit=9 bytes_invalid=0 send_seq=152 receive_seq=152 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999439 Octopus_Pro_H723_V1.1: temp=30.2 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=483 bytes_read=8593 bytes_retransmit=0 bytes_invalid=0 send_seq=79 receive_seq=79 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999899 adj=31998698 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=50.4 th1: temp=50.6 th2: temp=55.5 th3: temp=54.3 sysload=0.48 cputime=644.207 memavail=7399292 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8883.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4634 bytes_read=10007 bytes_retransmit=9 bytes_invalid=0 send_seq=352 receive_seq=352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015899 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1042 bytes_read=5207 bytes_retransmit=0 bytes_invalid=0 send_seq=145 receive_seq=145 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999278 adj=49997260 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1588 bytes_read=7293 bytes_retransmit=9 bytes_invalid=0 send_seq=180 receive_seq=180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997675 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1577 bytes_read=7272 bytes_retransmit=9 bytes_invalid=0 send_seq=178 receive_seq=178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997484 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1173 bytes_read=9488 bytes_retransmit=9 bytes_invalid=0 send_seq=149 receive_seq=149 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997646 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1802 bytes_read=5106 bytes_retransmit=9 bytes_invalid=0 send_seq=153 receive_seq=153 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999434 Octopus_Pro_H723_V1.1: temp=30.2 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=489 bytes_read=8949 bytes_retransmit=0 bytes_invalid=0 send_seq=80 receive_seq=80 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999901 adj=31998699 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=50.3 th1: temp=50.6 th2: temp=55.5 th3: temp=54.3 sysload=0.48 cputime=644.239 memavail=7399292 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8884.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4640 bytes_read=10139 bytes_retransmit=9 bytes_invalid=0 send_seq=353 receive_seq=353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015892 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1048 bytes_read=5223 bytes_retransmit=0 bytes_invalid=0 send_seq=146 receive_seq=146 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999273 adj=49997266 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1594 bytes_read=7393 bytes_retransmit=9 bytes_invalid=0 send_seq=181 receive_seq=181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997657 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1583 bytes_read=7372 bytes_retransmit=9 bytes_invalid=0 send_seq=179 receive_seq=179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000022 adj=63997493 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1179 bytes_read=9720 bytes_retransmit=9 bytes_invalid=0 send_seq=150 receive_seq=150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1808 bytes_read=5122 bytes_retransmit=9 bytes_invalid=0 send_seq=154 receive_seq=154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999431 Octopus_Pro_H723_V1.1: temp=30.4 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=495 bytes_read=9305 bytes_retransmit=0 bytes_invalid=0 send_seq=81 receive_seq=81 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999902 adj=31998695 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=50.3 th1: temp=50.6 th2: temp=55.5 th3: temp=54.1 sysload=0.48 cputime=644.270 memavail=7399292 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8885.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4646 bytes_read=10242 bytes_retransmit=9 bytes_invalid=0 send_seq=354 receive_seq=354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015885 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1054 bytes_read=5239 bytes_retransmit=0 bytes_invalid=0 send_seq=147 receive_seq=147 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999270 adj=49997242 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1600 bytes_read=7521 bytes_retransmit=9 bytes_invalid=0 send_seq=182 receive_seq=182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000188 adj=63997655 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1589 bytes_read=7500 bytes_retransmit=9 bytes_invalid=0 send_seq=180 receive_seq=180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000025 adj=63997486 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1185 bytes_read=10012 bytes_retransmit=9 bytes_invalid=0 send_seq=151 receive_seq=151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1814 bytes_read=5138 bytes_retransmit=9 bytes_invalid=0 send_seq=155 receive_seq=155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999436 Octopus_Pro_H723_V1.1: temp=30.1 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=501 bytes_read=9661 bytes_retransmit=0 bytes_invalid=0 send_seq=82 receive_seq=82 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999902 adj=31998690 coil_temp=16.9 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=50.2 th1: temp=50.5 th2: temp=55.4 th3: temp=54.1 sysload=0.48 cputime=644.304 memavail=7399292 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 8886.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4652 bytes_read=10345 bytes_retransmit=9 bytes_invalid=0 send_seq=355 receive_seq=355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015887 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1060 bytes_read=5255 bytes_retransmit=0 bytes_invalid=0 send_seq=148 receive_seq=148 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999272 adj=49997242 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1606 bytes_read=7635 bytes_retransmit=9 bytes_invalid=0 send_seq=183 receive_seq=183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000189 adj=63997655 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1595 bytes_read=7600 bytes_retransmit=9 bytes_invalid=0 send_seq=181 receive_seq=181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997513 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1191 bytes_read=10259 bytes_retransmit=9 bytes_invalid=0 send_seq=152 receive_seq=152 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1820 bytes_read=5165 bytes_retransmit=9 bytes_invalid=0 send_seq=156 receive_seq=156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999435 Octopus_Pro_H723_V1.1: temp=30.2 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=507 bytes_read=10017 bytes_retransmit=0 bytes_invalid=0 send_seq=83 receive_seq=83 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999904 adj=31998681 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=50.2 th1: temp=50.4 th2: temp=55.3 th3: temp=54.1 sysload=0.48 cputime=644.336 memavail=7399292 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 8887.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4658 bytes_read=10491 bytes_retransmit=9 bytes_invalid=0 send_seq=356 receive_seq=356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015888 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1066 bytes_read=5271 bytes_retransmit=0 bytes_invalid=0 send_seq=149 receive_seq=149 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999276 adj=49997263 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1612 bytes_read=7735 bytes_retransmit=9 bytes_invalid=0 send_seq=184 receive_seq=184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997658 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1601 bytes_read=7714 bytes_retransmit=9 bytes_invalid=0 send_seq=182 receive_seq=182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000023 adj=63997489 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1197 bytes_read=10491 bytes_retransmit=9 bytes_invalid=0 send_seq=153 receive_seq=153 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1826 bytes_read=5181 bytes_retransmit=9 bytes_invalid=0 send_seq=157 receive_seq=157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999437 Octopus_Pro_H723_V1.1: temp=30.3 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=513 bytes_read=10373 bytes_retransmit=0 bytes_invalid=0 send_seq=84 receive_seq=84 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999906 adj=31998677 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=50.2 th1: temp=50.4 th2: temp=55.2 th3: temp=54.0 sysload=0.44 cputime=644.368 memavail=7399316 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8888.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4664 bytes_read=10594 bytes_retransmit=9 bytes_invalid=0 send_seq=357 receive_seq=357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015888 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1072 bytes_read=5300 bytes_retransmit=0 bytes_invalid=0 send_seq=150 receive_seq=150 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999280 adj=49997298 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1618 bytes_read=7863 bytes_retransmit=9 bytes_invalid=0 send_seq=185 receive_seq=185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000190 adj=63997660 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1607 bytes_read=7842 bytes_retransmit=9 bytes_invalid=0 send_seq=183 receive_seq=183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63997490 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1203 bytes_read=10783 bytes_retransmit=9 bytes_invalid=0 send_seq=154 receive_seq=154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1832 bytes_read=5197 bytes_retransmit=9 bytes_invalid=0 send_seq=158 receive_seq=158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=30.5 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=519 bytes_read=10729 bytes_retransmit=0 bytes_invalid=0 send_seq=85 receive_seq=85 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998678 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=50.1 th1: temp=50.4 th2: temp=55.2 th3: temp=54.0 sysload=0.44 cputime=644.402 memavail=7398056 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8889.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4670 bytes_read=10693 bytes_retransmit=9 bytes_invalid=0 send_seq=358 receive_seq=358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015882 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1078 bytes_read=5316 bytes_retransmit=0 bytes_invalid=0 send_seq=151 receive_seq=151 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999280 adj=49997333 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1624 bytes_read=7963 bytes_retransmit=9 bytes_invalid=0 send_seq=186 receive_seq=186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997659 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1613 bytes_read=7942 bytes_retransmit=9 bytes_invalid=0 send_seq=184 receive_seq=184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000027 adj=63997497 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1209 bytes_read=11015 bytes_retransmit=9 bytes_invalid=0 send_seq=155 receive_seq=155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1838 bytes_read=5213 bytes_retransmit=9 bytes_invalid=0 send_seq=159 receive_seq=159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999442 Octopus_Pro_H723_V1.1: temp=30.4 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=525 bytes_read=11085 bytes_retransmit=0 bytes_invalid=0 send_seq=86 receive_seq=86 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999910 adj=31998692 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=50.1 th1: temp=50.3 th2: temp=55.1 th3: temp=53.9 sysload=0.44 cputime=644.434 memavail=7398068 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8890.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4676 bytes_read=10823 bytes_retransmit=9 bytes_invalid=0 send_seq=359 receive_seq=359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015884 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1084 bytes_read=5332 bytes_retransmit=0 bytes_invalid=0 send_seq=152 receive_seq=152 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999281 adj=49997327 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1630 bytes_read=8063 bytes_retransmit=9 bytes_invalid=0 send_seq=187 receive_seq=187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997801 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1619 bytes_read=8042 bytes_retransmit=9 bytes_invalid=0 send_seq=185 receive_seq=185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997521 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1215 bytes_read=11247 bytes_retransmit=9 bytes_invalid=0 send_seq=156 receive_seq=156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1844 bytes_read=5229 bytes_retransmit=9 bytes_invalid=0 send_seq=160 receive_seq=160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999444 Octopus_Pro_H723_V1.1: temp=30.4 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=531 bytes_read=11441 bytes_retransmit=0 bytes_invalid=0 send_seq=87 receive_seq=87 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999908 adj=31998682 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=50.2 th1: temp=50.3 th2: temp=55.1 th3: temp=53.8 sysload=0.44 cputime=644.465 memavail=7398068 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8891.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4682 bytes_read=10926 bytes_retransmit=9 bytes_invalid=0 send_seq=360 receive_seq=360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015879 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1090 bytes_read=5348 bytes_retransmit=0 bytes_invalid=0 send_seq=153 receive_seq=153 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999277 adj=49997323 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1636 bytes_read=8205 bytes_retransmit=9 bytes_invalid=0 send_seq=188 receive_seq=188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997798 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1625 bytes_read=8170 bytes_retransmit=9 bytes_invalid=0 send_seq=186 receive_seq=186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997534 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1221 bytes_read=11554 bytes_retransmit=9 bytes_invalid=0 send_seq=157 receive_seq=157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997642 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1850 bytes_read=5256 bytes_retransmit=9 bytes_invalid=0 send_seq=161 receive_seq=161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999440 Octopus_Pro_H723_V1.1: temp=30.4 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=537 bytes_read=11797 bytes_retransmit=0 bytes_invalid=0 send_seq=88 receive_seq=88 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999914 adj=31998661 coil_temp=16.9 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=49.9 th1: temp=50.3 th2: temp=55.1 th3: temp=53.8 sysload=0.44 cputime=644.499 memavail=7398076 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 8892.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4688 bytes_read=11043 bytes_retransmit=9 bytes_invalid=0 send_seq=361 receive_seq=361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015872 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1096 bytes_read=5364 bytes_retransmit=0 bytes_invalid=0 send_seq=154 receive_seq=154 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999273 adj=49997289 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1642 bytes_read=8305 bytes_retransmit=9 bytes_invalid=0 send_seq=189 receive_seq=189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997754 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1631 bytes_read=8284 bytes_retransmit=9 bytes_invalid=0 send_seq=187 receive_seq=187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000034 adj=63997529 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1227 bytes_read=11786 bytes_retransmit=9 bytes_invalid=0 send_seq=158 receive_seq=158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1856 bytes_read=5272 bytes_retransmit=9 bytes_invalid=0 send_seq=162 receive_seq=162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=30.5 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=543 bytes_read=12153 bytes_retransmit=0 bytes_invalid=0 send_seq=89 receive_seq=89 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999915 adj=31998696 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=49.9 th1: temp=50.3 th2: temp=55.0 th3: temp=53.8 sysload=0.41 cputime=644.531 memavail=7398076 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8893.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4694 bytes_read=11175 bytes_retransmit=9 bytes_invalid=0 send_seq=362 receive_seq=362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015891 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1102 bytes_read=5393 bytes_retransmit=0 bytes_invalid=0 send_seq=155 receive_seq=155 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999288 adj=49997265 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1648 bytes_read=8405 bytes_retransmit=9 bytes_invalid=0 send_seq=190 receive_seq=190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997729 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1637 bytes_read=8384 bytes_retransmit=9 bytes_invalid=0 send_seq=188 receive_seq=188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000034 adj=63997565 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1233 bytes_read=12018 bytes_retransmit=9 bytes_invalid=0 send_seq=159 receive_seq=159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997651 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1862 bytes_read=5288 bytes_retransmit=9 bytes_invalid=0 send_seq=163 receive_seq=163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999446 Octopus_Pro_H723_V1.1: temp=30.3 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=549 bytes_read=12509 bytes_retransmit=0 bytes_invalid=0 send_seq=90 receive_seq=90 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998694 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=50.0 th1: temp=50.2 th2: temp=54.8 th3: temp=53.7 sysload=0.41 cputime=644.567 memavail=7392032 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 8894.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4700 bytes_read=11278 bytes_retransmit=9 bytes_invalid=0 send_seq=363 receive_seq=363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015896 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1108 bytes_read=5409 bytes_retransmit=0 bytes_invalid=0 send_seq=156 receive_seq=156 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999287 adj=49997380 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1654 bytes_read=8533 bytes_retransmit=9 bytes_invalid=0 send_seq=191 receive_seq=191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997717 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1643 bytes_read=8512 bytes_retransmit=9 bytes_invalid=0 send_seq=189 receive_seq=189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000034 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1239 bytes_read=12310 bytes_retransmit=9 bytes_invalid=0 send_seq=160 receive_seq=160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1868 bytes_read=5304 bytes_retransmit=9 bytes_invalid=0 send_seq=164 receive_seq=164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999456 Octopus_Pro_H723_V1.1: temp=30.4 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=555 bytes_read=12865 bytes_retransmit=0 bytes_invalid=0 send_seq=91 receive_seq=91 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998698 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=49.9 th1: temp=50.1 th2: temp=54.8 th3: temp=53.5 sysload=0.41 cputime=644.601 memavail=7398180 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 8895.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4706 bytes_read=11381 bytes_retransmit=9 bytes_invalid=0 send_seq=364 receive_seq=364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015885 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1114 bytes_read=5425 bytes_retransmit=0 bytes_invalid=0 send_seq=157 receive_seq=157 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999287 adj=49997349 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1660 bytes_read=8633 bytes_retransmit=9 bytes_invalid=0 send_seq=192 receive_seq=192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997688 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1649 bytes_read=8612 bytes_retransmit=9 bytes_invalid=0 send_seq=190 receive_seq=190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000033 adj=63997503 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1245 bytes_read=12542 bytes_retransmit=9 bytes_invalid=0 send_seq=161 receive_seq=161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997691 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1874 bytes_read=5320 bytes_retransmit=9 bytes_invalid=0 send_seq=165 receive_seq=165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999456 Octopus_Pro_H723_V1.1: temp=30.6 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=561 bytes_read=13221 bytes_retransmit=0 bytes_invalid=0 send_seq=92 receive_seq=92 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999920 adj=31998690 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=49.8 th1: temp=50.1 th2: temp=54.8 th3: temp=53.6 sysload=0.41 cputime=644.633 memavail=7398180 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 8896.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4712 bytes_read=11513 bytes_retransmit=9 bytes_invalid=0 send_seq=365 receive_seq=365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015880 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1120 bytes_read=5441 bytes_retransmit=0 bytes_invalid=0 send_seq=158 receive_seq=158 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999285 adj=49997349 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1666 bytes_read=8733 bytes_retransmit=9 bytes_invalid=0 send_seq=193 receive_seq=193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997688 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1655 bytes_read=8712 bytes_retransmit=9 bytes_invalid=0 send_seq=191 receive_seq=191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997509 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1251 bytes_read=12789 bytes_retransmit=9 bytes_invalid=0 send_seq=162 receive_seq=162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997683 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1880 bytes_read=5347 bytes_retransmit=9 bytes_invalid=0 send_seq=166 receive_seq=166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999451 Octopus_Pro_H723_V1.1: temp=30.6 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=567 bytes_read=13577 bytes_retransmit=0 bytes_invalid=0 send_seq=93 receive_seq=93 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998691 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=49.7 th1: temp=50.0 th2: temp=54.7 th3: temp=53.6 sysload=0.41 cputime=644.666 memavail=7398180 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 8897.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4718 bytes_read=11630 bytes_retransmit=9 bytes_invalid=0 send_seq=366 receive_seq=366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015870 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1126 bytes_read=5457 bytes_retransmit=0 bytes_invalid=0 send_seq=159 receive_seq=159 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999283 adj=49997321 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1672 bytes_read=8875 bytes_retransmit=9 bytes_invalid=0 send_seq=194 receive_seq=194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997686 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1661 bytes_read=8854 bytes_retransmit=9 bytes_invalid=0 send_seq=192 receive_seq=192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000033 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1257 bytes_read=13081 bytes_retransmit=9 bytes_invalid=0 send_seq=163 receive_seq=163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1886 bytes_read=5363 bytes_retransmit=9 bytes_invalid=0 send_seq=167 receive_seq=167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999446 Octopus_Pro_H723_V1.1: temp=30.5 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=573 bytes_read=13933 bytes_retransmit=0 bytes_invalid=0 send_seq=94 receive_seq=94 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999916 adj=31998670 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=49.8 th1: temp=50.0 th2: temp=54.7 th3: temp=53.6 sysload=0.37 cputime=644.699 memavail=7398180 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8898.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4724 bytes_read=11733 bytes_retransmit=9 bytes_invalid=0 send_seq=367 receive_seq=367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015866 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1132 bytes_read=5486 bytes_retransmit=0 bytes_invalid=0 send_seq=160 receive_seq=160 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999280 adj=49997308 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1678 bytes_read=8975 bytes_retransmit=9 bytes_invalid=0 send_seq=195 receive_seq=195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997681 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1667 bytes_read=8954 bytes_retransmit=9 bytes_invalid=0 send_seq=193 receive_seq=193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000034 adj=63997548 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1263 bytes_read=13313 bytes_retransmit=9 bytes_invalid=0 send_seq=164 receive_seq=164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997694 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1892 bytes_read=5379 bytes_retransmit=9 bytes_invalid=0 send_seq=168 receive_seq=168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999444 Octopus_Pro_H723_V1.1: temp=30.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=579 bytes_read=14289 bytes_retransmit=0 bytes_invalid=0 send_seq=95 receive_seq=95 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999918 adj=31998657 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=49.8 th1: temp=50.0 th2: temp=54.6 th3: temp=53.5 sysload=0.37 cputime=644.731 memavail=7398180 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 8899.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4730 bytes_read=11865 bytes_retransmit=9 bytes_invalid=0 send_seq=368 receive_seq=368 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015860 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1138 bytes_read=5502 bytes_retransmit=0 bytes_invalid=0 send_seq=161 receive_seq=161 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999280 adj=49997286 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1684 bytes_read=9075 bytes_retransmit=9 bytes_invalid=0 send_seq=196 receive_seq=196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997687 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1673 bytes_read=9054 bytes_retransmit=9 bytes_invalid=0 send_seq=194 receive_seq=194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000033 adj=63997546 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1269 bytes_read=13545 bytes_retransmit=9 bytes_invalid=0 send_seq=165 receive_seq=165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1898 bytes_read=5395 bytes_retransmit=9 bytes_invalid=0 send_seq=169 receive_seq=169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999467 Octopus_Pro_H723_V1.1: temp=30.7 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=585 bytes_read=14645 bytes_retransmit=0 bytes_invalid=0 send_seq=96 receive_seq=96 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999919 adj=31998670 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=49.7 th1: temp=49.9 th2: temp=54.6 th3: temp=53.5 sysload=0.37 cputime=644.763 memavail=7400080 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8900.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4736 bytes_read=11963 bytes_retransmit=9 bytes_invalid=0 send_seq=369 receive_seq=369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015860 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1144 bytes_read=5518 bytes_retransmit=0 bytes_invalid=0 send_seq=162 receive_seq=162 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999280 adj=49997294 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1690 bytes_read=9203 bytes_retransmit=9 bytes_invalid=0 send_seq=197 receive_seq=197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997729 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1679 bytes_read=9182 bytes_retransmit=9 bytes_invalid=0 send_seq=195 receive_seq=195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1275 bytes_read=13837 bytes_retransmit=9 bytes_invalid=0 send_seq=166 receive_seq=166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997677 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1904 bytes_read=5411 bytes_retransmit=9 bytes_invalid=0 send_seq=170 receive_seq=170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999463 Octopus_Pro_H723_V1.1: temp=30.8 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=591 bytes_read=15001 bytes_retransmit=0 bytes_invalid=0 send_seq=97 receive_seq=97 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999921 adj=31998677 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=49.7 th1: temp=49.9 th2: temp=54.6 th3: temp=53.5 sysload=0.37 cputime=644.796 memavail=7400080 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 8901.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4742 bytes_read=12066 bytes_retransmit=9 bytes_invalid=0 send_seq=370 receive_seq=370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015857 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1150 bytes_read=5534 bytes_retransmit=0 bytes_invalid=0 send_seq=163 receive_seq=163 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999282 adj=49997297 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1696 bytes_read=9303 bytes_retransmit=9 bytes_invalid=0 send_seq=198 receive_seq=198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997700 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1685 bytes_read=9282 bytes_retransmit=9 bytes_invalid=0 send_seq=196 receive_seq=196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000033 adj=63997515 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1281 bytes_read=14084 bytes_retransmit=9 bytes_invalid=0 send_seq=167 receive_seq=167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1910 bytes_read=5438 bytes_retransmit=9 bytes_invalid=0 send_seq=171 receive_seq=171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999458 Octopus_Pro_H723_V1.1: temp=30.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=597 bytes_read=15357 bytes_retransmit=0 bytes_invalid=0 send_seq=98 receive_seq=98 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998687 coil_temp=16.9 refs=0 mcu_temp=20.36 supply_voltage=3.012 th0: temp=49.7 th1: temp=49.9 th2: temp=54.5 th3: temp=53.4 sysload=0.37 cputime=644.828 memavail=7400096 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 8902.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4748 bytes_read=12212 bytes_retransmit=9 bytes_invalid=0 send_seq=371 receive_seq=371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015852 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1156 bytes_read=5550 bytes_retransmit=0 bytes_invalid=0 send_seq=164 receive_seq=164 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999284 adj=49997321 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1702 bytes_read=9417 bytes_retransmit=9 bytes_invalid=0 send_seq=199 receive_seq=199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997690 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1691 bytes_read=9396 bytes_retransmit=9 bytes_invalid=0 send_seq=197 receive_seq=197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000032 adj=63997525 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1287 bytes_read=14316 bytes_retransmit=9 bytes_invalid=0 send_seq=168 receive_seq=168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997678 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1916 bytes_read=5454 bytes_retransmit=9 bytes_invalid=0 send_seq=172 receive_seq=172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999451 Octopus_Pro_H723_V1.1: temp=30.8 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=603 bytes_read=15713 bytes_retransmit=0 bytes_invalid=0 send_seq=99 receive_seq=99 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998707 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=49.6 th1: temp=49.9 th2: temp=54.6 th3: temp=53.3 sysload=0.34 cputime=644.860 memavail=7400096 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8903.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4754 bytes_read=12315 bytes_retransmit=9 bytes_invalid=0 send_seq=372 receive_seq=372 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015849 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1162 bytes_read=5579 bytes_retransmit=0 bytes_invalid=0 send_seq=165 receive_seq=165 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999286 adj=49997345 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1708 bytes_read=9545 bytes_retransmit=9 bytes_invalid=0 send_seq=200 receive_seq=200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997699 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1697 bytes_read=9524 bytes_retransmit=9 bytes_invalid=0 send_seq=198 receive_seq=198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1293 bytes_read=14608 bytes_retransmit=9 bytes_invalid=0 send_seq=169 receive_seq=169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1922 bytes_read=5470 bytes_retransmit=9 bytes_invalid=0 send_seq=173 receive_seq=173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999447 Octopus_Pro_H723_V1.1: temp=30.7 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=609 bytes_read=16069 bytes_retransmit=0 bytes_invalid=0 send_seq=100 receive_seq=100 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998698 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=49.6 th1: temp=49.9 th2: temp=54.5 th3: temp=53.4 sysload=0.34 cputime=644.893 memavail=7400096 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 8904.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4760 bytes_read=12418 bytes_retransmit=9 bytes_invalid=0 send_seq=373 receive_seq=373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015857 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1168 bytes_read=5595 bytes_retransmit=0 bytes_invalid=0 send_seq=166 receive_seq=166 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999285 adj=49997352 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1714 bytes_read=9645 bytes_retransmit=9 bytes_invalid=0 send_seq=201 receive_seq=201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997692 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1703 bytes_read=9624 bytes_retransmit=9 bytes_invalid=0 send_seq=199 receive_seq=199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997540 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1299 bytes_read=14840 bytes_retransmit=9 bytes_invalid=0 send_seq=170 receive_seq=170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999560 adj=47997666 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1928 bytes_read=5486 bytes_retransmit=9 bytes_invalid=0 send_seq=174 receive_seq=174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999455 Octopus_Pro_H723_V1.1: temp=30.6 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=615 bytes_read=16425 bytes_retransmit=0 bytes_invalid=0 send_seq=101 receive_seq=101 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998683 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=49.4 th1: temp=49.8 th2: temp=54.4 th3: temp=53.3 sysload=0.34 cputime=644.925 memavail=7400096 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8905.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4766 bytes_read=12550 bytes_retransmit=9 bytes_invalid=0 send_seq=374 receive_seq=374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015851 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1174 bytes_read=5611 bytes_retransmit=0 bytes_invalid=0 send_seq=167 receive_seq=167 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999282 adj=49997322 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1720 bytes_read=9745 bytes_retransmit=9 bytes_invalid=0 send_seq=202 receive_seq=202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997666 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1709 bytes_read=9724 bytes_retransmit=9 bytes_invalid=0 send_seq=200 receive_seq=200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997517 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1305 bytes_read=15072 bytes_retransmit=9 bytes_invalid=0 send_seq=171 receive_seq=171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999558 adj=47997727 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1934 bytes_read=5502 bytes_retransmit=9 bytes_invalid=0 send_seq=175 receive_seq=175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999445 Octopus_Pro_H723_V1.1: temp=31.0 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=621 bytes_read=16781 bytes_retransmit=0 bytes_invalid=0 send_seq=102 receive_seq=102 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998674 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=49.4 th1: temp=49.8 th2: temp=54.3 th3: temp=53.3 sysload=0.34 cputime=644.956 memavail=7400096 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 8906.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4772 bytes_read=12653 bytes_retransmit=9 bytes_invalid=0 send_seq=375 receive_seq=375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015849 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1180 bytes_read=5627 bytes_retransmit=0 bytes_invalid=0 send_seq=168 receive_seq=168 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999280 adj=49997290 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1726 bytes_read=9873 bytes_retransmit=9 bytes_invalid=0 send_seq=203 receive_seq=203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997672 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1715 bytes_read=9852 bytes_retransmit=9 bytes_invalid=0 send_seq=201 receive_seq=201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997531 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1311 bytes_read=15379 bytes_retransmit=9 bytes_invalid=0 send_seq=172 receive_seq=172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997696 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1940 bytes_read=5529 bytes_retransmit=9 bytes_invalid=0 send_seq=176 receive_seq=176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999454 Octopus_Pro_H723_V1.1: temp=31.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=627 bytes_read=17137 bytes_retransmit=0 bytes_invalid=0 send_seq=103 receive_seq=103 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998679 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=49.5 th1: temp=49.8 th2: temp=54.3 th3: temp=53.2 sysload=0.34 cputime=644.989 memavail=7400096 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 8907.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4778 bytes_read=12770 bytes_retransmit=9 bytes_invalid=0 send_seq=376 receive_seq=376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015859 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1186 bytes_read=5643 bytes_retransmit=0 bytes_invalid=0 send_seq=169 receive_seq=169 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999280 adj=49997284 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1732 bytes_read=9987 bytes_retransmit=9 bytes_invalid=0 send_seq=204 receive_seq=204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997698 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1721 bytes_read=9966 bytes_retransmit=9 bytes_invalid=0 send_seq=202 receive_seq=202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000037 adj=63997553 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1317 bytes_read=15611 bytes_retransmit=9 bytes_invalid=0 send_seq=173 receive_seq=173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997672 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1946 bytes_read=5545 bytes_retransmit=9 bytes_invalid=0 send_seq=177 receive_seq=177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999449 Octopus_Pro_H723_V1.1: temp=31.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=633 bytes_read=17493 bytes_retransmit=0 bytes_invalid=0 send_seq=104 receive_seq=104 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998674 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=49.5 th1: temp=49.7 th2: temp=54.3 th3: temp=53.2 sysload=0.32 cputime=645.020 memavail=7400096 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8908.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4784 bytes_read=12902 bytes_retransmit=9 bytes_invalid=0 send_seq=377 receive_seq=377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015858 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1192 bytes_read=5672 bytes_retransmit=0 bytes_invalid=0 send_seq=170 receive_seq=170 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999279 adj=49997264 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1738 bytes_read=10087 bytes_retransmit=9 bytes_invalid=0 send_seq=205 receive_seq=205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997660 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1727 bytes_read=10066 bytes_retransmit=9 bytes_invalid=0 send_seq=203 receive_seq=203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997515 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1323 bytes_read=15843 bytes_retransmit=9 bytes_invalid=0 send_seq=174 receive_seq=174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1952 bytes_read=5561 bytes_retransmit=9 bytes_invalid=0 send_seq=178 receive_seq=178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999442 Octopus_Pro_H723_V1.1: temp=31.0 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=639 bytes_read=17849 bytes_retransmit=0 bytes_invalid=0 send_seq=105 receive_seq=105 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998667 coil_temp=16.9 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=49.4 th1: temp=49.6 th2: temp=54.3 th3: temp=53.2 sysload=0.32 cputime=645.052 memavail=7398360 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 8909.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4790 bytes_read=13005 bytes_retransmit=9 bytes_invalid=0 send_seq=378 receive_seq=378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015868 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1198 bytes_read=5688 bytes_retransmit=0 bytes_invalid=0 send_seq=171 receive_seq=171 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999278 adj=49997274 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1744 bytes_read=10215 bytes_retransmit=9 bytes_invalid=0 send_seq=206 receive_seq=206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63997651 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1733 bytes_read=10194 bytes_retransmit=9 bytes_invalid=0 send_seq=204 receive_seq=204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997503 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1329 bytes_read=16135 bytes_retransmit=9 bytes_invalid=0 send_seq=175 receive_seq=175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997619 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1958 bytes_read=5577 bytes_retransmit=9 bytes_invalid=0 send_seq=179 receive_seq=179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999442 Octopus_Pro_H723_V1.1: temp=30.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=645 bytes_read=18205 bytes_retransmit=0 bytes_invalid=0 send_seq=106 receive_seq=106 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998681 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=49.5 th1: temp=49.6 th2: temp=54.2 th3: temp=53.1 sysload=0.32 cputime=645.085 memavail=7398360 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8910.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4796 bytes_read=13108 bytes_retransmit=9 bytes_invalid=0 send_seq=379 receive_seq=379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015882 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1204 bytes_read=5704 bytes_retransmit=0 bytes_invalid=0 send_seq=172 receive_seq=172 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999277 adj=49997253 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1750 bytes_read=10315 bytes_retransmit=9 bytes_invalid=0 send_seq=207 receive_seq=207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997636 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1739 bytes_read=10294 bytes_retransmit=9 bytes_invalid=0 send_seq=205 receive_seq=205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000035 adj=63997482 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1335 bytes_read=16367 bytes_retransmit=9 bytes_invalid=0 send_seq=176 receive_seq=176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997602 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1964 bytes_read=5593 bytes_retransmit=9 bytes_invalid=0 send_seq=180 receive_seq=180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999438 Octopus_Pro_H723_V1.1: temp=31.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=651 bytes_read=18561 bytes_retransmit=0 bytes_invalid=0 send_seq=107 receive_seq=107 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999925 adj=31998666 coil_temp=16.9 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=49.3 th1: temp=49.6 th2: temp=54.2 th3: temp=53.0 sysload=0.32 cputime=645.118 memavail=7392588 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 8911.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4802 bytes_read=13235 bytes_retransmit=9 bytes_invalid=0 send_seq=380 receive_seq=380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015878 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1210 bytes_read=5720 bytes_retransmit=0 bytes_invalid=0 send_seq=173 receive_seq=173 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999300 adj=49997225 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1756 bytes_read=10415 bytes_retransmit=9 bytes_invalid=0 send_seq=208 receive_seq=208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997603 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1745 bytes_read=10394 bytes_retransmit=9 bytes_invalid=0 send_seq=206 receive_seq=206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997454 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1341 bytes_read=16614 bytes_retransmit=9 bytes_invalid=0 send_seq=177 receive_seq=177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997585 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1970 bytes_read=5620 bytes_retransmit=9 bytes_invalid=0 send_seq=181 receive_seq=181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999429 Octopus_Pro_H723_V1.1: temp=30.9 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.3 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=657 bytes_read=18917 bytes_retransmit=0 bytes_invalid=0 send_seq=108 receive_seq=108 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999924 adj=31998651 coil_temp=16.9 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=49.4 th1: temp=49.7 th2: temp=54.1 th3: temp=53.0 sysload=0.32 cputime=645.153 memavail=7397472 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 8912.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4808 bytes_read=13352 bytes_retransmit=9 bytes_invalid=0 send_seq=381 receive_seq=381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015871 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1216 bytes_read=5736 bytes_retransmit=0 bytes_invalid=0 send_seq=174 receive_seq=174 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999298 adj=49997501 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1762 bytes_read=10553 bytes_retransmit=9 bytes_invalid=0 send_seq=209 receive_seq=209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000205 adj=63997618 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1751 bytes_read=10532 bytes_retransmit=9 bytes_invalid=0 send_seq=207 receive_seq=207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997574 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1347 bytes_read=16906 bytes_retransmit=9 bytes_invalid=0 send_seq=178 receive_seq=178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997602 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1976 bytes_read=5636 bytes_retransmit=9 bytes_invalid=0 send_seq=182 receive_seq=182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999439 Octopus_Pro_H723_V1.1: temp=31.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=663 bytes_read=19273 bytes_retransmit=0 bytes_invalid=0 send_seq=109 receive_seq=109 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998646 coil_temp=16.9 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=49.3 th1: temp=49.5 th2: temp=54.1 th3: temp=53.0 sysload=0.29 cputime=645.186 memavail=7397472 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 8913.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4814 bytes_read=13455 bytes_retransmit=9 bytes_invalid=0 send_seq=382 receive_seq=382 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015876 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1222 bytes_read=5765 bytes_retransmit=0 bytes_invalid=0 send_seq=175 receive_seq=175 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999297 adj=49997449 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1768 bytes_read=10645 bytes_retransmit=9 bytes_invalid=0 send_seq=210 receive_seq=210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997657 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1757 bytes_read=10623 bytes_retransmit=9 bytes_invalid=0 send_seq=208 receive_seq=208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997564 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1353 bytes_read=17138 bytes_retransmit=9 bytes_invalid=0 send_seq=179 receive_seq=179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997617 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1982 bytes_read=5652 bytes_retransmit=9 bytes_invalid=0 send_seq=183 receive_seq=183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999439 Octopus_Pro_H723_V1.1: temp=31.0 EBB42_Gen2_v1.0_T0: temp=30.4 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=669 bytes_read=19629 bytes_retransmit=0 bytes_invalid=0 send_seq=110 receive_seq=110 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999923 adj=31998648 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=49.3 th1: temp=49.6 th2: temp=54.0 th3: temp=53.0 sysload=0.29 cputime=645.218 memavail=7397472 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 8914.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4820 bytes_read=13587 bytes_retransmit=9 bytes_invalid=0 send_seq=383 receive_seq=383 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015889 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1228 bytes_read=5781 bytes_retransmit=0 bytes_invalid=0 send_seq=176 receive_seq=176 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999295 adj=49997394 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1774 bytes_read=10738 bytes_retransmit=9 bytes_invalid=0 send_seq=211 receive_seq=211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997688 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1763 bytes_read=10716 bytes_retransmit=9 bytes_invalid=0 send_seq=209 receive_seq=209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000044 adj=63997540 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1359 bytes_read=17370 bytes_retransmit=9 bytes_invalid=0 send_seq=180 receive_seq=180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997674 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1988 bytes_read=5668 bytes_retransmit=9 bytes_invalid=0 send_seq=184 receive_seq=184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999434 Octopus_Pro_H723_V1.1: temp=31.0 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=675 bytes_read=19985 bytes_retransmit=0 bytes_invalid=0 send_seq=111 receive_seq=111 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998643 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=49.2 th1: temp=49.5 th2: temp=54.0 th3: temp=53.0 sysload=0.29 cputime=645.249 memavail=7397472 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8915.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4826 bytes_read=13690 bytes_retransmit=9 bytes_invalid=0 send_seq=384 receive_seq=384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015882 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1234 bytes_read=5797 bytes_retransmit=0 bytes_invalid=0 send_seq=177 receive_seq=177 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999295 adj=49997338 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1780 bytes_read=10857 bytes_retransmit=9 bytes_invalid=0 send_seq=212 receive_seq=212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63997686 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1769 bytes_read=10835 bytes_retransmit=9 bytes_invalid=0 send_seq=210 receive_seq=210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000051 adj=63997510 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1365 bytes_read=17662 bytes_retransmit=9 bytes_invalid=0 send_seq=181 receive_seq=181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997643 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1994 bytes_read=5684 bytes_retransmit=9 bytes_invalid=0 send_seq=185 receive_seq=185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999428 Octopus_Pro_H723_V1.1: temp=31.1 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=681 bytes_read=20341 bytes_retransmit=0 bytes_invalid=0 send_seq=112 receive_seq=112 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998774 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=49.2 th1: temp=49.5 th2: temp=53.9 th3: temp=52.9 sysload=0.29 cputime=645.281 memavail=7397472 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 8916.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4832 bytes_read=13793 bytes_retransmit=9 bytes_invalid=0 send_seq=385 receive_seq=385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015874 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1240 bytes_read=5813 bytes_retransmit=0 bytes_invalid=0 send_seq=178 receive_seq=178 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999294 adj=49997331 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1786 bytes_read=10952 bytes_retransmit=9 bytes_invalid=0 send_seq=213 receive_seq=213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997744 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1775 bytes_read=10930 bytes_retransmit=9 bytes_invalid=0 send_seq=211 receive_seq=211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997592 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1371 bytes_read=17909 bytes_retransmit=9 bytes_invalid=0 send_seq=182 receive_seq=182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999553 adj=47997655 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2000 bytes_read=5711 bytes_retransmit=9 bytes_invalid=0 send_seq=186 receive_seq=186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999429 Octopus_Pro_H723_V1.1: temp=31.1 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=687 bytes_read=20697 bytes_retransmit=0 bytes_invalid=0 send_seq=113 receive_seq=113 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998737 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=49.1 th1: temp=49.4 th2: temp=54.0 th3: temp=52.9 sysload=0.29 cputime=645.313 memavail=7397224 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8917.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4838 bytes_read=13939 bytes_retransmit=9 bytes_invalid=0 send_seq=386 receive_seq=386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015881 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1246 bytes_read=5829 bytes_retransmit=0 bytes_invalid=0 send_seq=179 receive_seq=179 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999291 adj=49997327 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1792 bytes_read=11066 bytes_retransmit=9 bytes_invalid=0 send_seq=214 receive_seq=214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997730 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1781 bytes_read=11044 bytes_retransmit=9 bytes_invalid=0 send_seq=212 receive_seq=212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997577 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1377 bytes_read=18141 bytes_retransmit=9 bytes_invalid=0 send_seq=183 receive_seq=183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997653 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2006 bytes_read=5727 bytes_retransmit=9 bytes_invalid=0 send_seq=187 receive_seq=187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999436 Octopus_Pro_H723_V1.1: temp=31.2 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=26.8  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=693 bytes_read=21053 bytes_retransmit=0 bytes_invalid=0 send_seq=114 receive_seq=114 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998710 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=49.1 th1: temp=49.4 th2: temp=53.9 th3: temp=52.9 sysload=0.27 cputime=645.344 memavail=7397224 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 8918.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4844 bytes_read=14042 bytes_retransmit=9 bytes_invalid=0 send_seq=387 receive_seq=387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015890 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1252 bytes_read=5858 bytes_retransmit=0 bytes_invalid=0 send_seq=180 receive_seq=180 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999289 adj=49997282 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1798 bytes_read=11194 bytes_retransmit=9 bytes_invalid=0 send_seq=215 receive_seq=215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997697 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1787 bytes_read=11172 bytes_retransmit=9 bytes_invalid=0 send_seq=213 receive_seq=213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1383 bytes_read=18433 bytes_retransmit=9 bytes_invalid=0 send_seq=184 receive_seq=184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997629 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2012 bytes_read=5743 bytes_retransmit=9 bytes_invalid=0 send_seq=188 receive_seq=188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999432 Octopus_Pro_H723_V1.1: temp=31.0 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=699 bytes_read=21409 bytes_retransmit=0 bytes_invalid=0 send_seq=115 receive_seq=115 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998669 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=49.1 th1: temp=49.4 th2: temp=53.9 th3: temp=52.8 sysload=0.27 cputime=645.377 memavail=7395752 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 8919.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4850 bytes_read=14145 bytes_retransmit=9 bytes_invalid=0 send_seq=388 receive_seq=388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015879 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1258 bytes_read=5874 bytes_retransmit=0 bytes_invalid=0 send_seq=181 receive_seq=181 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999289 adj=49997257 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1804 bytes_read=11294 bytes_retransmit=9 bytes_invalid=0 send_seq=216 receive_seq=216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997664 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1793 bytes_read=11272 bytes_retransmit=9 bytes_invalid=0 send_seq=214 receive_seq=214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997633 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1389 bytes_read=18665 bytes_retransmit=9 bytes_invalid=0 send_seq=185 receive_seq=185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997610 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2018 bytes_read=5759 bytes_retransmit=9 bytes_invalid=0 send_seq=189 receive_seq=189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999429 Octopus_Pro_H723_V1.1: temp=31.2 EBB42_Gen2_v1.0_T0: temp=30.6 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=705 bytes_read=21765 bytes_retransmit=0 bytes_invalid=0 send_seq=116 receive_seq=116 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998657 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=49.1 th1: temp=49.4 th2: temp=53.8 th3: temp=52.8 sysload=0.27 cputime=645.409 memavail=7395752 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8920.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4856 bytes_read=14277 bytes_retransmit=9 bytes_invalid=0 send_seq=389 receive_seq=389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015871 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1264 bytes_read=5890 bytes_retransmit=0 bytes_invalid=0 send_seq=182 receive_seq=182 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999288 adj=49997273 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1810 bytes_read=11394 bytes_retransmit=9 bytes_invalid=0 send_seq=217 receive_seq=217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997670 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1799 bytes_read=11372 bytes_retransmit=9 bytes_invalid=0 send_seq=215 receive_seq=215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997605 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1395 bytes_read=18897 bytes_retransmit=9 bytes_invalid=0 send_seq=186 receive_seq=186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997627 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2024 bytes_read=5775 bytes_retransmit=9 bytes_invalid=0 send_seq=190 receive_seq=190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999438 Octopus_Pro_H723_V1.1: temp=31.1 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.1 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=711 bytes_read=22121 bytes_retransmit=0 bytes_invalid=0 send_seq=117 receive_seq=117 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998650 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=49.0 th1: temp=49.3 th2: temp=53.8 th3: temp=52.9 sysload=0.27 cputime=645.441 memavail=7395540 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=18.1 pwm=0.000
Stats 8921.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4862 bytes_read=14378 bytes_retransmit=9 bytes_invalid=0 send_seq=390 receive_seq=390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015864 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1270 bytes_read=5906 bytes_retransmit=0 bytes_invalid=0 send_seq=183 receive_seq=183 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999287 adj=49997283 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1816 bytes_read=11522 bytes_retransmit=9 bytes_invalid=0 send_seq=218 receive_seq=218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000212 adj=63997679 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1805 bytes_read=11500 bytes_retransmit=9 bytes_invalid=0 send_seq=216 receive_seq=216 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000069 adj=63997667 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1401 bytes_read=19204 bytes_retransmit=9 bytes_invalid=0 send_seq=187 receive_seq=187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997632 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2030 bytes_read=5802 bytes_retransmit=9 bytes_invalid=0 send_seq=191 receive_seq=191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999439 Octopus_Pro_H723_V1.1: temp=31.2 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=717 bytes_read=22477 bytes_retransmit=0 bytes_invalid=0 send_seq=118 receive_seq=118 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998650 coil_temp=16.9 refs=0 mcu_temp=20.33 supply_voltage=3.012 th0: temp=49.0 th1: temp=49.3 th2: temp=53.8 th3: temp=52.8 sysload=0.27 cputime=645.474 memavail=7395540 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.7 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 8922.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4868 bytes_read=14492 bytes_retransmit=9 bytes_invalid=0 send_seq=391 receive_seq=391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015856 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1276 bytes_read=5922 bytes_retransmit=0 bytes_invalid=0 send_seq=184 receive_seq=184 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999287 adj=49997297 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1822 bytes_read=11636 bytes_retransmit=9 bytes_invalid=0 send_seq=219 receive_seq=219 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000211 adj=63997698 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1811 bytes_read=11614 bytes_retransmit=9 bytes_invalid=0 send_seq=217 receive_seq=217 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997708 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1407 bytes_read=19436 bytes_retransmit=9 bytes_invalid=0 send_seq=188 receive_seq=188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997637 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2036 bytes_read=5818 bytes_retransmit=9 bytes_invalid=0 send_seq=192 receive_seq=192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999451 Octopus_Pro_H723_V1.1: temp=31.3 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.2 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=723 bytes_read=22833 bytes_retransmit=0 bytes_invalid=0 send_seq=119 receive_seq=119 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998708 coil_temp=16.9 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=49.0 th1: temp=49.3 th2: temp=53.8 th3: temp=52.8 sysload=0.25 cputime=645.507 memavail=7395540 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Stats 8923.5: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4874 bytes_read=14624 bytes_retransmit=9 bytes_invalid=0 send_seq=392 receive_seq=392 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015848 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1282 bytes_read=5951 bytes_retransmit=0 bytes_invalid=0 send_seq=185 receive_seq=185 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999285 adj=49997301 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1828 bytes_read=11736 bytes_retransmit=9 bytes_invalid=0 send_seq=220 receive_seq=220 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000210 adj=63997704 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1817 bytes_read=11714 bytes_retransmit=9 bytes_invalid=0 send_seq=218 receive_seq=218 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997644 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1413 bytes_read=19668 bytes_retransmit=9 bytes_invalid=0 send_seq=189 receive_seq=189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2042 bytes_read=5834 bytes_retransmit=9 bytes_invalid=0 send_seq=193 receive_seq=193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999454 Octopus_Pro_H723_V1.1: temp=31.3 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=729 bytes_read=23189 bytes_retransmit=0 bytes_invalid=0 send_seq=120 receive_seq=120 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998690 coil_temp=16.9 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=49.0 th1: temp=49.2 th2: temp=53.7 th3: temp=52.7 sysload=0.25 cputime=645.540 memavail=7395540 print_time=17.774 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.9 pwm=0.000 extruder1: target=0 temp=18.0 pwm=0.000
Stats 9061.6: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=5720 bytes_read=30529 bytes_retransmit=9 bytes_invalid=0 send_seq=533 receive_seq=533 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015514 rpi: mcu_awake=0.000 mcu_task_avg=0.000008 mcu_task_stddev=0.000008 bytes_write=2128 bytes_read=8548 bytes_retransmit=0 bytes_invalid=0 send_seq=326 receive_seq=326 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999285 adj=49997366 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=2674 bytes_read=27199 bytes_retransmit=9 bytes_invalid=0 send_seq=361 receive_seq=361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997754 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=2663 bytes_read=27177 bytes_retransmit=9 bytes_invalid=0 send_seq=359 receive_seq=359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997579 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=2259 bytes_read=54738 bytes_retransmit=9 bytes_invalid=0 send_seq=330 receive_seq=330 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999534 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2888 bytes_read=8398 bytes_retransmit=9 bytes_invalid=0 send_seq=334 receive_seq=334 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999455 Octopus_Pro_H723_V1.1: temp=33.4 EBB42_Gen2_v1.0_T0: temp=30.5 EBB42_Gen2_v1.0_T1: temp=29.0 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1575 bytes_read=72240 bytes_retransmit=0 bytes_invalid=0 send_seq=261 receive_seq=261 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999928 adj=31998706 coil_temp=17.0 refs=0 mcu_temp=20.42 supply_voltage=3.011 th0: temp=46.2 th1: temp=46.3 th2: temp=50.7 th3: temp=49.7 sysload=0.04 cputime=649.971 memavail=7397212 print_time=215.234 buffer_time=0.041 print_stall=0 extruder: target=0 temp=18.8 pwm=0.000 extruder1: target=0 temp=17.9 pwm=0.000
Attempting MCU 'mcu' reset command
Attempting MCU 'rpi' config_reset command
b'Got EOF when reading from device'
Attempting MCU 'toolboard_t0' reset command
Attempting MCU 'toolboard_t1' reset command
Attempting MCU 'dinghy' reset command
Attempting MCU 'plasma' reset command
Attempting MCU 'beacon' reset command
webhooks client 3977449800: Disconnected
Restarting printer
Start printer at Tue Mar 17 03:50:58 2026 (1773719458.6 9062.9)
===== Config file =====
[mcu rpi]
serial = /tmp/klipper_host_mcu

[board_pins btt-octopus-pro-h723-11]
aliases = 
	
	
	
	x_step_pin=PF13,
	x_dir_pin=PF12,
	x_enable_pin=PF14,
	x_uart_pin=PC4,
	x_diag_pin=PG6,
	x_endstop_pin=PG6,
	
	
	
	dual_carriage_step_pin=PF9,
	dual_carriage_dir_pin=PF10,
	dual_carriage_enable_pin=PG2,
	dual_carriage_uart_pin=PF2,
	dual_carriage_diag_pin=PG12,
	dual_carriage_endstop_pin=PG12,
	
	
	
	y_step_pin=PG0,
	y_dir_pin=PG1,
	y_enable_pin=PF15,
	y_uart_pin=PD11,
	y_diag_pin=PG9,
	y_endstop_pin=PG9,
	
	
	
	y1_step_pin=PG4,
	y1_dir_pin=PC1,
	y1_enable_pin=PA2,
	y1_uart_pin=PC7,
	y1_diag_pin=PG11,
	y1_endstop_pin=PG11,
	
	
	
	z0_step_pin=PC13,
	z0_dir_pin=PF0,
	z0_enable_pin=PF1,
	z0_uart_pin=PE4,
	z0_diag_pin=PG13,
	
	
	
	z1_step_pin=PE2,
	z1_dir_pin=PE3,
	z1_enable_pin=PD4,
	z1_uart_pin=PE1,
	z1_diag_pin=PG14,
	
	
	
	z2_step_pin=PE6,
	z2_dir_pin=PA14,
	z2_enable_pin=PE0,
	z2_uart_pin=PD3,
	z2_diag_pin=PG15,
	
	e_step_pin=PF11,
	e_dir_pin=PG3,
	e_enable_pin=PG5,
	e_uart_pin=PC6,
	
	e_heater_pin=PA2,
	e_sensor_pin=PF4,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=PA7,
	stepper_spi_miso_pin=PA6,
	stepper_spi_sclk_pin=PA5,
	adxl345_cs_pin=PA15,
	bltouch_sensor_pin=PB7,
	bltouch_control_pin=PB6,
	probe_pin=PB7,
	fan_part_cooling_pin=PA8,
	fan_toolhead_cooling_pin=PE5,
	fan_controller_board_pin=PD12,
	heater_bed_heating_pin=PA1,
	heater_bed_sensor_pin=PF3,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PG15,
	filament_sensor_motion_pin=PG14,
	ratrig_vaoc_probe_pin=PG10,
	ratrig_vaoc_led_pin=PB0,
	ratrig_vaoc_fan_pin=PD13,
	chamber_lighting_pin=PB11,
	chamber_filter_4p_fan_pin=PD14,
	chamber_filter_4p_fan_enable_pin=PD15

[mcu]
serial = /dev/RatOS/btt-octopus-pro-h723-11

[temperature_sensor Octopus_Pro_H723_V1.1]
sensor_type = temperature_mcu

[adxl345 controlboard]
cs_pin = PA15
spi_software_mosi_pin = PB5
spi_software_miso_pin = PB4
spi_software_sclk_pin = PB3

[board_pins toolboard_t0]
mcu = toolboard_t0
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t0]
serial = /dev/RatOS/btt-ebb42-gen2-10-t0

[temperature_sensor EBB42_Gen2_v1.0_T0]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t0

[lis2dw toolboard_t0]
axes_map = x, z, y
cs_pin = toolboard_t0:PB1
spi_software_mosi_pin = toolboard_t0:PB11
spi_software_miso_pin = toolboard_t0:PB2
spi_software_sclk_pin = toolboard_t0:PB10

[board_pins toolboard_t1]
mcu = toolboard_t1
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t1]
serial = /dev/RatOS/btt-ebb42-gen2-10-t1

[temperature_sensor EBB42_Gen2_v1.0_T1]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t1

[lis2dw toolboard_t1]
axes_map = x, z, y
cs_pin = toolboard_t1:PB1
spi_software_mosi_pin = toolboard_t1:PB11
spi_software_miso_pin = toolboard_t1:PB2
spi_software_sclk_pin = toolboard_t1:PB10

[gcode_macro RatOS]
variable_homing = "endstops"
variable_z_probe = "static"
variable_sensorless_x_current = 0.6
variable_sensorless_y_current = 0.9
variable_safe_home_x = "middle"
variable_safe_home_y = "middle"
variable_driver_type_x = "tmc2209"
variable_driver_type_y = "tmc2209"
variable_stowable_probe_stop_on_error = False
variable_chamber_filter_enable = True
variable_chamber_filter_speed = 0.5
variable_chamber_filter_disable_speed = 1.0
variable_chamber_filter_enable_at = "after_print_start"
variable_chamber_filter_disable_period = 300
variable_chamber_filter_disable_bed_temp = 0
variable_chamber_heater_enable = True
variable_chamber_heater_bed_temp = 115
variable_chamber_heater_preheating_temp = 150
variable_chamber_heater_heating_temp_offset = 25
variable_chamber_heater_control_external_heater = False
variable_chamber_heater_air_circulation_enable = True
variable_chamber_heater_air_circulation_fan_speed = 0.35
variable_chamber_heater_air_circulation_y_pos = 0
variable_chamber_heater_air_circulation_z_pos = 100
variable_chamber_heater_extra_fan_speed = 1.0
variable_chamber_heater_filter_fan_speed = 1.0
variable_bed_heat_soak_time = 0
variable_hotend_heat_soak_time = 0
variable_led_status_action = 0.0,1.0,1.0
variable_led_status_success = 0.0,1.0,0.0
variable_led_status_error = 1.0,0.0,1.0
variable_led_status_on = 1.0,1.0,1.0
variable_led_status_off = 0.0,0.0,1.0
variable_led_status_standby = 0.1,0.1,0.1
variable_led_status_heating = 1.0,0.0,0.0
variable_led_status_cooling = 0.0,0.0,1.0
variable_calibrate_bed_mesh = True
variable_adaptive_mesh = True
variable_start_print_park_in = "center"
variable_start_print_park_z_height = 3
variable_end_print_park_in = "back"
variable_pause_print_park_in = "back"
variable_end_print_park_z_hop = 20
variable_nozzle_priming = "primeblob"
variable_nozzle_prime_start_x = "max"
variable_nozzle_prime_start_y = "min"
variable_nozzle_prime_direction = "auto"
variable_nozzle_prime_bridge_fan = 102
variable_probe_for_priming_result = None
variable_probe_for_priming_end_result = None
variable_probe_for_priming_result_t1 = None
variable_probe_for_priming_end_result_t1 = None
variable_probe_for_priming_disable_mesh_constraints = False
variable_adaptive_prime_offset_threshold = -1.0
variable_last_z_offset = None
variable_runout_park_in = "front"
variable_enable_unload_tip_forming = False
variable_filament_unload_length = 150
description = RatOS variable storage macro, will echo variables to the console when run.
variable_relative_extrusion = True
variable_force_absolute_position = False
variable_preheat_extruder = True
variable_preheat_extruder_temp = 150
variable_macro_travel_speed = 600
variable_macro_travel_accel = 8000
variable_macro_z_speed = 15
variable_bed_margin_x = [59.6, 59.6]
variable_bed_margin_y = [14.35, 33.65]
variable_printable_x_min = 0
variable_printable_x_max = 0
variable_printable_y_min = 0
variable_printable_y_max = 0
variable_end_print_motors_off = True
variable_status_color_ok = "00FF00"
variable_status_color_error = "FF0000"
variable_status_color_unknown = "FFFF00"
variable_end_print_retract_filament = 10
gcode = 
	ECHO_RATOS_VARS
variable_auto_center_subject = False
variable_toolchange_zhop = 2.0
variable_toolchange_zspeed = 25
variable_toolchange_sync_fans = False
variable_toolchange_combined_zhop = False
variable_toolchange_travel_speed = 600
variable_toolchange_travel_accel = 8000
variable_toolchange_extrusion = 2.0
variable_toolchange_retraction = 2.0
variable_toolchange_feedrate = 7200
variable_toolchange_prepurging_timer = 0
variable_toolchange_standby_temp = -1
variable_toolchange_purge = 25
variable_toolchange_first_purge = 50
variable_beacon_bed_mesh_scv = 25
variable_beacon_contact_z_homing = False
variable_beacon_contact_start_print_true_zero = True
variable_beacon_contact_start_print_true_zero_fuzzy_position = True
variable_beacon_contact_calibrate_model_on_true_zero = True
variable_beacon_contact_wipe_before_true_zero = True
variable_beacon_contact_wipe_before_true_zero_method = "probe_clean"
variable_beacon_contact_true_zero_temp = 170
variable_beacon_contact_prime_probing = True
variable_beacon_contact_expansion_compensation = True
variable_beacon_contact_bed_mesh = False
variable_beacon_contact_bed_mesh_samples = 2
variable_beacon_contact_z_tilt_adjust = False
variable_beacon_contact_z_tilt_adjust_samples = 2
variable_beacon_scan_compensation_enable = True
variable_beacon_scan_compensation_profile = "auto"
variable_beacon_scan_compensation_desired_spacing = 10
variable_beacon_scan_compensation_bed_temp_mismatch_is_error = False
variable_beacon_contact_poke_bottom_limit = -1
variable_beacon_scan_method_automatic = False
variable_beacon_adaptive_heat_soak = True
variable_beacon_adaptive_heat_soak_max_wait = 5400
variable_beacon_adaptive_heat_soak_extra_wait_after_completion = 0
variable_beacon_adaptive_heat_soak_layer_quality = 3
variable_beacon_adaptive_heat_soak_maximum_first_layer_duration = 1800
variable_beacon_contact_start_print_true_zero_fuzzy_radius = 20
variable_homing_x = "endstop"
variable_homing_y = "endstop"
variable_default_toolhead = 0
variable_adxl_chip = ["lis2dw toolboard_t0", "lis2dw toolboard_t1"]
variable_shaper_x_freq = [54.2, 53.2, 53.6, 54.4]
variable_shaper_y_freq = [40.8, 47.6, 38.6, 38]
variable_shaper_x_type = ["mzv", "mzv", "mzv", "mzv"]
variable_shaper_y_type = ["mzv", "mzv", "mzv", "mzv"]
variable_x_driver_types = ["tmc5160"]
variable_x_axes = ["x"]
variable_y_driver_types = ["tmc5160", "tmc5160"]
variable_y_axes = ["y", "y1"]
variable_z_driver_types = ["tmc2209", "tmc2209", "tmc2209"]
variable_z_axes = ["z", "z1", "z2"]
variable_home_y_first = True

[ratos_homing]
axes = xyz
z_hop = 15
z_hop_speed = 15
gcode = 
	
	_LED_ON
	
	
	{% set prev_stop_on_error = printer["gcode_macro RatOS"].stowable_probe_stop_on_error %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set target_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	_IDEX_SINGLE
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE=True
	
	
	M400
	
	G90
	
	
	{% set X = true if params.X is defined else false %}
	{% set Y = true if params.Y is defined else false %}
	{% set Z = true if params.Z is defined else false %}
	{% if printer["gcode_macro RatOS"].home_y_first|default(false)|lower == 'true' %}
	HOME_Y X={X} Y={Y} Z={Z}
	HOME_X X={X} Y={Y} Z={Z}
	{% else %}
	HOME_X X={X} Y={Y} Z={Z}
	HOME_Y X={X} Y={Y} Z={Z}
	{% endif %}
	HOME_Z X={X} Y={Y} Z={Z}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE={prev_stop_on_error}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[gcode_macro HOME_X]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_x = printer["gcode_macro RatOS"].homing_x|lower %}
	{% set homing_x = homing_x if homing_x else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_X" MSG="printable_x_max: {printable_x_max}, safe_home_x: {safe_home_x}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}"
	
	
	{% if X or not Y and not Z %}
	{% if homing_x == 'endstop' %}
	G28 X
	{% elif homing_x == 'sensorless' %}
	{% if printer["dual_carriage"] is defined %}
	{ action_emergency_stop("sensorless homing not supported on IDEX!") }
	{% endif %}
	HOME_X_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_x to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_x, homing)) }
	{% endif %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1} MODE=PRIMARY
	G1 X{parking_position} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	{% endif %}
	{% set x_homed = True %}
	G0 X{safe_home_x} F{speed}
	M400
	{% endif %}

[gcode_macro HOME_Y]
gcode = 
	
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_y = printer["gcode_macro RatOS"].homing_y|lower %}
	{% set homing_y = homing_y if homing_y else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Y" MSG="printable_y_max: {printable_y_max}, safe_home_y: {safe_home_y}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}"
	
	
	{% if Y or not X and not Z %}
	{% if homing_y == 'endstop' %}
	G28 Y
	{% elif homing_y == 'sensorless' %}
	HOME_Y_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_y to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_y, homing)) }
	{% endif %}
	{% set y_homed = True %}
	G0 Y{safe_home_y} F{speed}
	{% endif %}

[gcode_macro HOME_Z]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	
	
	{% set beacon_contact_z_homing = true if printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_z_home_position_fuzzing_radius = printer["gcode_macro RatOS"].beacon_z_home_position_fuzzing_radius|default(0)|float %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Z" MSG="x_homed: {x_homed}, y_homed: {y_homed}, z_probe: {z_probe}, beacon_contact_z_homing: {beacon_contact_z_homing}"
	
	
	{% if Z or not Y and not X %}
	RATOS_ECHO MSG="Homing Z"
	{% if x_homed == False or y_homed == False %}
	{ action_emergency_stop("X and Y must be homed before homing Z") }
	{% else %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_homing %}
	{% if beacon_contact_start_print_true_zero %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% else %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	{% else %}
	G28 Z
	{% endif %}
	_Z_HOP
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro HOME_X_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	
	G4 P300
	
	G28 X
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"

[gcode_macro HOME_Y_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	
	G4 P300
	
	G28 Y
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"

[gcode_macro _Z_HOP]
description = Move Z axis up by Z_HOP distance at Z_HOP_SPEED. In relative mode it will move Z axis up by Z_HOP distance. In absolute mode it will move Z axis to Z_HOP distance.
gcode = 
	{% set z_hop = printer.fastconfig.config.ratos_homing.z_hop|float %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	G0 Z{z_hop} F{z_hop_speed}

[gcode_macro __MOVE_TO_SAFE_Z_HOME_ECHO_DEBUG]
gcode = 
	DEBUG_ECHO PREFIX="_MOVE_TO_SAFE_Z_HOME" MSG="x: {params.X}, y: {params.Y}, z_hop: {params.Z_HOP}, fuzzy_radius: {params.FUZZY_RADIUS}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}, printable_x_max: {printer['gcode_macro RatOS'].printable_x_max}, printable_y_max: {printer['gcode_macro RatOS'].printable_y_max}"

[gcode_macro MAYBE_HOME]
description = Only home unhomed axis. Specify ABL=1 to also ensure that automatic bed levelling is applied (if configured).
variable_is_kinematic_position_overriden = False
gcode = 
	{% set abl = params.ABL|default('')|lower in ('true', 'yes', '1') %}
	{% if printer["gcode_macro MAYBE_HOME"].is_kinematic_position_overriden|lower == 'true' %}
	RATOS_ECHO MSG="SET_CENTER_KINEMATIC_POSITION has been abused. Homing all axes. Please refrain from using SET_CENTER_KINEMATIC_POSITION outside of debugging purposes."
	G28
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=False
	{% else %}
	{% set axes = '' %}
	{% set isHomed = true %}
	{% set axesToHome = '' %}
	{% if params.X is defined %}
	{% set axes = axes ~ 'X ' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% endif %}
	{% if params.Y is defined %}
	{% set axes = axes ~ 'Y ' %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% endif %}
	{% if params.Z is defined %}
	{% set axes = axes ~ 'Z ' %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if params.X is not defined and params.Y is not defined and params.Z is not defined %}
	{% set axes = '' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if isHomed is false %}
	RATOS_ECHO MSG="Homing {axesToHome}"
	G28 {axesToHome}
	{% else %}
	RATOS_ECHO MSG="All requested axes already homed. Skipping homing."
	{% endif %}
	{% endif %}
	{% if abl %}
	{% if printer.z_tilt is defined %}
	{% if not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Performing Z tilt adjustment..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Z tilt already applied. Skipping Z tilt adjustment."
	{% endif %}
	{% elif printer.quad_gantry_level is defined %}
	{% if not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Performing quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Quad gantry leveling already applied. Skipping quad gantry leveling."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="No automatic bed leveling method configured. Skipping bed leveling."
	{% endif %}
	{% endif %}

[gcode_macro PID_CALIBRATE_HOTEND]
description = Perform a PID calibration test for a given extruder heater.
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set temp = params.TEMP|default(220)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_HOTEND" MSG="TEMP={temp}"
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO MSG="PID calibration hotend heater T0 at {temp}°C..."
	PID_CALIBRATE HEATER=extruder TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	
	{% if toolhead==0 or toolhead==1 %}
	RATOS_ECHO MSG="PID calibration hotend heater T{toolhead} at {temp}°C..."
	PID_CALIBRATE HEATER=extruder{'' if toolhead==0 else toolhead} TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_BED]
description = Perform a PID calibration test for the bed heater.
gcode = 
	
	{% set temp = params.TEMP|default(80)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_BED" MSG="TEMP={temp}"
	RATOS_ECHO MSG="PID calibration bed heater at {temp}°C..."
	
	
	PID_CALIBRATE HEATER=heater_bed TARGET={temp}
	
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_CHAMBER_HEATER]
description = Perform a PID calibration test for the chamber heater.
gcode = 
	
	{% set temp = params.TEMP|default(150)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_CHAMBER_HEATER" MSG="TEMP={temp}"
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	RATOS_ECHO MSG="PID calibration chamber heater at {temp}°C..."
	PID_CALIBRATE HEATER=chamber_heater TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_heater" %}
	{% set link_text = "RatOS Chamber Heater" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber heater found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro INITIALIZE_PA_TUNING]
description = Start a pressure advance tuning tower.
gcode = 
	
	{% set start = params.START|default(0.0)|float %}
	{% set factor = params.FACTOR|default(0.001)|float %}
	
	
	{% set layer_number = printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|default(0)|int %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if is_printing_gcode and layer_number < 2 %}
	DEBUG_ECHO PREFIX="START_PA_TOWER" MSG="START: {start}, FACTOR: {factor}"
	RATOS_ECHO MSG="Starting pressure advance tuning tower..."
	TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START={start} FACTOR={factor}
	{% else %}
	RATOS_ECHO MSG="Pressure advance tuning tower requires you to be printing gcode and on layer 1 to start."
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro CHAMBER_FILTER_ON]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	_CHAMBER_FILTER_TURN_ON
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro CHAMBER_FILTER_OFF]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Deactivating chamber filter..."
	_CHAMBER_FILTER_TURN_OFF
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set chamber_filter_enable_at = printer["gcode_macro RatOS"].chamber_filter_enable_at|default('after_print_start')|lower %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_ON" MSG="at: {at}, chamber_filter_enable: {chamber_filter_enable}, chamber_filter_enable_at: {chamber_filter_enable_at}, chamber_filter_speed: {chamber_filter_speed}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	{% if chamber_filter_enable_at == at %}
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	
	
	_CHAMBER_FILTER_TURN_ON AT={at}
	
	
	{% if chamber_filter_enable_at == "print_end" %}
	_LED_CHAMBER_FILTER_ON
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_OFF]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF" MSG="chamber_filter_enable: {chamber_filter_enable}, filter_disable_period: {filter_disable_period}, filter_disable_bed_temp: {filter_disable_bed_temp}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	
	{% if filter_disable_period > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting {filter_disable_period} seconds before turning chamber filter off..."
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION={filter_disable_period}
	{% endif %}
	
	
	{% if filter_disable_bed_temp > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting for bed temp to cool down to {filter_disable_bed_temp}°C to turn filter off..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM=0 MAXIMUM={filter_disable_bed_temp}
	_CHAMBER_FILTER_TURN_OFF
	_LED_CHAMBER_FILTER_OFF
	{% endif %}
	
	{% endif %}

[delayed_gcode _CHAMBER_FILTER_OFF_TIMER]
gcode = 
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF_TIMER" MSG="executed"
	
	
	_CHAMBER_FILTER_TURN_OFF
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Chamber filter turned off!"
	
	
	_LED_CHAMBER_FILTER_OFF

[gcode_macro _CHAMBER_FILTER_TURN_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_speed|default(0)|float %}
	{% if at == "print_end" %}
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_disable_speed|default(0)|float %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION=0
	
	
	SET_FAN_SPEED FAN=filter SPEED={chamber_filter_speed}

[gcode_macro _CHAMBER_FILTER_TURN_OFF]
gcode = 
	
	SET_FAN_SPEED FAN=filter SPEED=0

[gcode_macro _CHAMBER_FILTER_SANITY_CHECK]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	{% if filter_disable_bed_temp > 0 and filter_disable_period > 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable, not both.")}
	{% endif %}
	
	{% if filter_disable_bed_temp == 0 and filter_disable_period == 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable.")}
	{% endif %}
	
	{% endif %}

[gcode_macro CHAMBER_HEATER_ON]
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(45)|int %}
	
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp} IS_FROM_START_PRINT=False

[gcode_macro CHAMBER_HEATER_OFF]
gcode = 
	_CHAMBER_HEATER_OFF

[gcode_macro _CHAMBER_HEATER_ON]
variable_chamber_temp = 0
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	{% set is_from_start_print = true if params.IS_FROM_START_PRINT|default(True)|lower == 'true' else false %}
	
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set chamber_heater_enable = true if printer["gcode_macro RatOS"].chamber_heater_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}
	{% set chamber_heater_preheating_temp = printer["gcode_macro RatOS"].chamber_heater_preheating_temp|default(150)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	{% set chamber_heater_control_external_heater = true if printer["gcode_macro RatOS"].chamber_heater_control_external_heater|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_enable = true if printer["gcode_macro RatOS"].chamber_heater_air_circulation_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_fan_speed = printer["gcode_macro RatOS"].chamber_heater_air_circulation_fan_speed|default(0.35)|float %}
	{% set chamber_heater_air_circulation_y_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_y_pos|default(0)|float %}
	{% set chamber_heater_air_circulation_z_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_z_pos|default(100)|float %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_HEATER_ON" MSG="chamber_heater_enable: {chamber_heater_enable}, chamber_heater_preheating_temp: {chamber_heater_preheating_temp}, chamber_heater_heating_temp_offset: {chamber_heater_heating_temp_offset}, bed_temp: {bed_temp}, chamber_temp: {chamber_temp}, start_chamber_temp: {start_chamber_temp}"
	
	
	{% if chamber_heater_enable and chamber_temp > 0 and chamber_heater_bed_temp > 0 %}
	
	
	_LED_HEATING
	
	
	RATOS_ECHO MSG="Preheating chamber to {(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}°C..."
	
	
	{% set chamber_temp_sensor = "extruder" %}
	{% if printer["dual_carriage"] is defined and default_toolhead == 1 %}
	{% set chamber_temp_sensor = "extruder1" %}
	{% endif %}
	{% if printer["temperature_sensor chamber"] is defined %}
	{% set chamber_temp_sensor = "temperature_sensor chamber" %}
	{% endif %}
	
	
	{% set current_chamber_temp = printer['%s' % chamber_temp_sensor].temperature|int %}
	
	
	{% set needs_heating = current_chamber_temp < (start_chamber_temp if start_chamber_temp > 0 else chamber_temp) %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_BEFORE_PREHEATING
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	{% if not is_from_start_print %}
	MAYBE_HOME
	{% endif %}
	G0 Z{chamber_heater_air_circulation_z_pos} F{z_speed}
	G0 Y{chamber_heater_air_circulation_y_pos} F{speed}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * chamber_heater_air_circulation_fan_speed)}
	{% endif %}
	{% else %}
	{% if is_from_start_print %}
	G0 Z{z} F{z_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE={chamber_temp}
	
	
	{% if needs_heating %}
	
	
	M140 S{chamber_heater_bed_temp}
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={chamber_heater_preheating_temp}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	
	{% endif %}
	
	
	{% if needs_heating %}
	_CHAMBER_HEATER_EXTRA_FAN_ON
	{% endif %}
	
	
	{% if needs_heating %}
	TEMPERATURE_WAIT SENSOR="{chamber_temp_sensor}" MINIMUM={(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% endif %}
	
	
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED=0
	_CHAMBER_FILTER_ON AT="before_print_start"
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	G28 Z
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_AFTER_PREHEATING
	{% endif %}
	
	
	{% if printer["temperature_sensor chamber"] is defined %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined and chamber_heater_control_external_heater %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	
	
	_LED_SUCCESS
	
	{% endif %}

[gcode_macro _CHAMBER_HEATER_OFF]
gcode = 
	RATOS_ECHO MSG="Deactivating chamber heater..."
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=0
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE=0
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	
	
	_CHAMBER_HEATER_EXTRA_FAN_OFF

[delayed_gcode _CHAMBER_HEATER_CONTROL]
initial_duration = 0.
gcode = 
	
	{% set chamber_temp = printer["gcode_macro _CHAMBER_HEATER_ON"].chamber_temp|default(0)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	
	
	{% set current_chamber_temp = printer['temperature_sensor chamber'].temperature|int %}
	
	
	{% if current_chamber_temp < chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	{% endif %}
	
	
	{% if current_chamber_temp >= chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_ON]
gcode = 
	
	{% set chamber_heater_extra_fan_speed = printer["gcode_macro RatOS"].chamber_heater_extra_fan_speed|default(0.0)|float %}
	
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	{% if chamber_heater_extra_fan_speed > 0 %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED={chamber_heater_extra_fan_speed}
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_OFF]
gcode = 
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED=0
	{% endif %}

[gcode_macro _USER_CHAMBER_HEATER_BEFORE_PREHEATING]
description = Will be executed before chamber preheating, only if heating is needed.
gcode = 

[gcode_macro _USER_CHAMBER_HEATER_AFTER_PREHEATING]
description = Will be executed after chamber preheating, only if heating was needed.
gcode = 

[gcode_macro RESET_HEATSOAK_SETTINGS]
description = Resets all heatsoak-related settings to startup defaults
gcode = 
	HEATSOAK_SETTINGS ACTION=reset

[gcode_macro USE_ADAPTIVE_HEATSOAK]
description = Temporarily enables adaptive bed heatsoaking (if a beacon probe is present), will reset to printer.cfg settings
	when Klipper is restarted. Optionally specify QUALITY (1-5) and maximum FIRST_LAYER_DURATION (in minutes).
	Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.QUALITY|default("1..5") %}
	{% set _ = params.FIRST_LAYER_DURATION|default("1..120 minutes") %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("Adaptive heatsoaking is only available when a beacon probe is configured.") }
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_quality = (settings.variable_beacon_adaptive_heat_soak_layer_quality if defsrc == 'startup' else current.beacon_adaptive_heat_soak_layer_quality)|default(3)|int %}
	{% set default_first_layer_duration_secs = (settings.variable_beacon_adaptive_heat_soak_maximum_first_layer_duration if defsrc == 'startup' else current.beacon_adaptive_heat_soak_maximum_first_layer_duration)|default(1800)|int %}
	{% if params2.QUALITY is defined %}
	{% set quality = params2.QUALITY|int %}
	{% if quality < 1 or quality > 5 %}
	{ action_raise_error("QUALITY must be between 1 (rough) and 5 (maximum). Use 3 (normal) if unsure.") }
	{% endif %}
	{% else %}
	{% set quality = default_quality %}
	{% endif %}
	{% if params2.FIRST_LAYER_DURATION is defined %}
	{% set first_layer_duration_mins = params2.FIRST_LAYER_DURATION|float %}
	{% if first_layer_duration_mins <= 0 %}
	{ action_raise_error("FIRST_LAYER_DURATION must be a positive number specifying the maximum first layer duration in minutes.") }
	{% endif %}
	{% if first_layer_duration_mins > 120 %}
	CONSOLE_ECHO MSG="FIRST_LAYER_DURATION will be limited to 120 minutes. Values larger than this will not have an effect on soak time."
	{% set first_layer_duration_mins = 120 %}
	{% endif %}
	{% set first_layer_duration_secs = (first_layer_duration_mins * 60.0)|int %}
	{% else %}
	{% set first_layer_duration_secs = default_first_layer_duration_secs %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	{% endif %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=True beacon_adaptive_heat_soak_layer_quality={quality} beacon_adaptive_heat_soak_maximum_first_layer_duration={first_layer_duration_secs}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."

[gcode_macro USE_FIXED_HEATSOAK]
description = Temporarily enables fixed bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
	Optionally specify DURATION (in minutes). Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.DURATION|default("0..720 minutes") %}
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_duration = (settings.variable_bed_heat_soak_time if defsrc == 'startup' else current.bed_heat_soak_time)|default(0)|int %}
	{% if params2.DURATION is defined %}
	{% set duration_mins = params2.DURATION|float %}
	{% if duration_mins < 0 %}
	{ action_raise_error("DURATION must be a non-negative number specifying the heatsoak duration in minutes.") }
	{% endif %}
	{% if duration_mins > 720 %}
	CONSOLE_ECHO MSG="DURATION will be limited to 720 minutes (12 hours). If you really need a larger value, adjust printer.cfg instead."
	{% set duration_mins = 720 %}
	{% endif %}
	{% set duration_secs = (duration_mins * 60.0)|int %}
	{% else %}
	{% set duration_secs = default_duration %}
	{% set duration_mins = duration_secs / 60.0 %}
	{% endif %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% if has_beacon %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=False bed_heat_soak_time={duration_secs}
	{% else %}
	HEATSOAK_SETTINGS QUIET=1 bed_heat_soak_time={duration_secs}
	{% endif %}
	{% if duration_mins < 1e-3 %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% else %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% endif %}

[gcode_macro USE_NO_HEATSOAK]
description = Temporarily disables bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
gcode = 
	USE_FIXED_HEATSOAK DURATION=0

[gcode_macro HEATSOAK_SETTINGS]
description = Shows or adjusts heatsoak settings
	- With no arguments: shows current heatsoak settings, specify VERBOSE=1 for detailed output
	- With arguments: sets the specified settings. Use the full setting name without the variable_ prefix, e.g. bed_heat_soak_time=300 or beacon_adaptive_heat_soak_layer_quality=4. See printer.cfg for available settings.
variable_default_source = "startup"
gcode = 
	
	{% set params2 = params %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% set quiet = params2.pop("QUIET", None)|default("0") in ("1", "true", "yes") %}
	{% set verbose = params2.pop("VERBOSE", None)|default("0") in ("1", "true", "yes") %}
	{% if has_beacon %}
	{% set vars = (
	"beacon_adaptive_heat_soak",
	"beacon_adaptive_heat_soak_max_wait",
	"beacon_adaptive_heat_soak_extra_wait_after_completion",
	"beacon_adaptive_heat_soak_layer_quality",
	"beacon_adaptive_heat_soak_maximum_first_layer_duration",
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% else %}
	{% set vars = (
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% endif %}
	{% set action = "show" if params|length == 0 else params2.ACTION %}
	{% if action is defined and params|length > 1 %}
	{ action_raise_error("ACTION cannot be specified with other parameters.") }
	{% elif action is not defined %}
	{% for k, v in params2.items() %}
	{% set k = k|lower %}
	{% if k in vars %}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Setting {k} to {v}"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={k} VALUE={v}
	{% else %}
	{ action_raise_error("Parameter '%s' is not recognised. Note that adaptive heatsoaking settings can only be set when a beacon probe is configured." % k) }
	{% endif %}
	{% endfor %}
	{% elif action == "reset" %}
	_RESET_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	CONSOLE_ECHO MSG="Heatsoak settings have been reset to their original values."
	{% elif action == "show" %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% set is_adaptive = False if not has_beacon else current.beacon_adaptive_heat_soak|default("")|lower == "true" %}
	{% if is_adaptive %}
	{% set quality = current.beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set first_layer_duration_secs = current.beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."
	{% elif current.bed_heat_soak_time|default(0)|int > 0 %}
	{% set duration_mins = (current.bed_heat_soak_time|int / 60.0) %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% else %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% endif %}
	{% if verbose %}
	CONSOLE_ECHO MSG="Detailed settings:"
	_SHOW_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	{% endif %}
	{% else %}
	{ action_raise_error("Action '%s' is not recognised" % action) }
	{% endif %}

[gcode_macro _LED_START_PRINTING]
gcode = 
	_LED_ACTION

[gcode_macro _LED_START_PRINTING_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_PRINTING]
gcode = 
	_LED_ON TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_PAUSE]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_ON]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_OFF]
gcode = 
	_LED_STANDBY

[gcode_macro _LED_LOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_LOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_RUNOUT]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_CLOG]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_UNLOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_UNLOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_DEACTIVATE_TOOLHEAD]
gcode = 
	_LED_OFF TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_STANDBY]
gcode = 
	_LED_STANDBY TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_WAKEUP]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_MOTORS_OFF]
gcode = 
	_LED_STANDBY
	_LED_VAOC_OFF

[gcode_macro _LED_INPUT_SHAPER_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_INPUT_SHAPER_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_BEACON_CALIBRATION_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_VAOC_ON]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=1.0 GREEN=1.0 BLUE=1.0
	{% endif %}

[gcode_macro _LED_VAOC_OFF]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=0.0 GREEN=0.0 BLUE=0.0
	{% endif %}

[gcode_macro _LED_ACTION]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_action %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SUCCESS]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_success %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_HEATING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_heating %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_COOLING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_cooling %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ERROR]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_error %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ON]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_on %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_OFF]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_off %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_STANDBY]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_standby %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}
	
	{% if toolhead >= 0 %}
	{% if printer['neopixel nozzle_led_t%s' % toolhead] is defined  %}
	SET_LED LED={'nozzle_led_t%s' % toolhead} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% else %}
	{% if printer['neopixel nozzle_led_t0'] is defined  %}
	SET_LED LED={'nozzle_led_t0'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% if printer['neopixel nozzle_led_t1'] is defined %}
	SET_LED LED={'nozzle_led_t1'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% endif %}
	
	_USER_LED_SET { rawparams }

[gcode_macro _USER_LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}

[gcode_macro LOAD_FILAMENT]
description = Loads new filament. Note: be careful with PETG, make sure you inspect the tip of your filament before loading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% if filament_name == '' or filament_type == '' %}
	{% set filament_name = 'unknown' %}
	{% set filament_type = 'unknown' %}
	{% endif %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_LOAD_FILAMENT TEMP={temp} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_LOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_LOAD_FILAMENT]
description = Load filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_LOAD_FILAMENT" MSG="TEMP={temp}"
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=load_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	_LOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	
	
	RESTORE_GCODE_STATE NAME=load_state
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament load routine complete, please check that the filament was loaded correctly."

[gcode_macro _IDEX_LOAD_FILAMENT]
description = Load filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament into T{toolhead}..."
	
	DEBUG_ECHO PREFIX="_IDEX_LOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	_LOAD_FILAMENT TOOLHEAD={toolhead} TEMP={temp} AUTOMATED={automated}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="Filament load routine for T{toolhead} complete, please check that the filament was loaded correctly."

[gcode_macro _LOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default(false)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE TOOLHEAD={toolhead}
	_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into hotend.."
	G92 E0
	G0 E{extruder_gear_to_cooling_position_distance} F{extruder_load_speed}
	G92 E0
	M400
	RATOS_ECHO MSG="Filament loaded into hotend."

[gcode_macro _LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set load_speed = printer["gcode_macro T%s" % toolhead].filament_load_speed|float * 60 %}
	{% set filament_loading_nozzle_offset = printer["gcode_macro T%s" % toolhead].filament_loading_nozzle_offset|float %}
	{% set cooling_position_to_nozzle_distance = printer["gcode_macro T%s" % toolhead].cooling_position_to_nozzle_distance|float %}
	{% set purge_after_load = printer["gcode_macro T%s" % toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into nozzle... Please wait!"
	G92 E0
	
	G0 E{cooling_position_to_nozzle_distance + filament_loading_nozzle_offset} F{load_speed}
	G92 E0
	G4 P1000
	_PURGE_FILAMENT	TOOLHEAD={toolhead} E={purge_after_load}
	RATOS_ECHO MSG="Filament loaded into nozzle!"

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"
	
	
	{% set filament_grabbing_length = printer["gcode_macro T%s" % toolhead].filament_grabbing_length|float %}
	{% set filament_grabbing_speed = printer["gcode_macro T%s" % toolhead].filament_grabbing_speed|float %}
	{% set resume_after_insert = true if printer["gcode_macro T%s" % toolhead].resume_after_insert|default(true)|lower == 'true' else false %}
	{% set enable_insert_detection = true if printer["gcode_macro T%s" % toolhead].enable_insert_detection|default(true)|lower == 'true' else false %}
	
	
	{% set current_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	
	{% if enable_insert_detection %}
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="toolhead: {toolhead}, filament_grabbing_length: {filament_grabbing_length}, filament_grabbing_speed: {filament_grabbing_speed}, current_idex_mode: {current_idex_mode}"
	
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	RATOS_ECHO MSG="Filament inserted into T{toolhead}, loading..."
	
	
	FORCE_MOVE STEPPER={'extruder%s' % ('' if toolhead == 0 else toolhead)} DISTANCE={filament_grabbing_length} VELOCITY={filament_grabbing_speed}
	M400
	
	
	{% if printer.pause_resume.is_paused %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% if resume_after_insert %}
	RESUME
	{% endif %}
	{% else %}
	{% if not printer.virtual_sdcard.is_active %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"

[gcode_macro _PURGE_BEFORE_UNLOAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set purge_before_unload = printer["gcode_macro T%s" % toolhead].purge_before_unload|float %}
	
	DEBUG_ECHO PREFIX="_PURGE_BEFORE_UNLOAD" MSG="TOOLHEAD: {toolhead}"
	
	
	{% if purge_before_unload > 0 %}
	G92 E0
	G0 E{purge_before_unload} F300
	G92 E0
	M400
	{% endif %}

[gcode_macro _PURGE_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set e = params.E|int %}
	{% set r = params.R|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_PURGE_FILAMENT" MSG="TOOLHEAD: {toolhead}, E: {e}"
	
	
	{% if e > 0 %}
	
	
	G92 E0
	G0 E{e} F300
	G92 E0
	M400
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={0.4 if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={0.4 if toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * 0.4)}
	{% endif %}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if r > 0 %}
	G92 E0
	G0 E-{r} F300
	G92 E0
	M400
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro _MOVE_TO_LOADING_POSITION]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_MOVE_TO_LOADING_POSITION" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	
	G1 X{loading_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _CLEANING_MOVE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_CLEANING_MOVE" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].parking_position is defined and printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set parking_position = printer["gcode_macro T%s" % toolhead].parking_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	{% set cleaning_position = loading_position %}
	{% if loading_position == parking_position %}
	{% if loading_position > 0 %}
	{% set cleaning_position = loading_position - 30 %}
	{% else %}
	{% set cleaning_position = loading_position + 30 %}
	{% endif %}
	{% endif %}
	
	
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _BED_MESH_SANITY_CHECK]
gcode = 
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is defined %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_start_print_true_zero_fuzzy_position %}
	CONSOLE_ECHO TYPE="error" TITLE="Defined zero reference not compatible with fuzzy true zero" MSG="Using fuzzy start print true zero position is not compatible with a defined zero_reference_position value in the [bed_mesh] section in printer.cfg._N_Please remove the zero_reference_position value from the [bed_mesh] section, or disable fuzzy true zero position in printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_start_print_true_zero_fuzzy_position: False"
	_STOP_AND_RAISE_ERROR MSG="Defined zero reference not compatible with fuzzy true zero"
	{% elif zero_ref_pos[0]|float|round != safe_home_x|float|round or zero_ref_pos[1]|float|round != safe_home_y|float|round %}
	CONSOLE_ECHO TYPE="error" TITLE="Zero reference position does not match safe home position" MSG="Please update your bed mesh zero reference position in printer.cfg, like so:_N__N_[bed_mesh]_N_zero_reference_position: {safe_home_x|float|round},{safe_home_y|float|round}_N_"
	_STOP_AND_RAISE_ERROR MSG="Zero reference position does not match safe home position"
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_bed_mesh %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact bed mesh is enabled" MSG="Beacon contact bed mesh is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_bed_mesh: False"
	{% endif %}
	
	{% if beacon_scan_method_automatic %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon 'automatic' scan method is enabled" MSG="Beacon 'automatic' scan method is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_scan_method_automatic: False"
	{% endif %}
	
	{% if beacon_contact_z_tilt_adjust %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact z-tilt adjust is enabled" MSG="Beacon contact z-tilt adjust is enabled. This is not recommended for normal use and may result in inaccurate z-tilt adjustment._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_z_tilt_adjust: False"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH]
gcode = 
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE=None
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE=None
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION {rawparams}
	{% endif %}

[gcode_macro _START_PRINT_BED_MESH]
variable_actual_true_zero_position_x = None
variable_actual_true_zero_position_y = None
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set X=[params.X0|default(-1)|float, params.X1|default(-1)|float] %}
	{% set Y=[params.Y0|default(-1)|float, params.Y1|default(-1)|float] %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_BED_MESH" MSG="idex_mode: {idex_mode}, X: {X}, Y: {Y}"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is not defined %}
	{% set zero_ref_pos = [safe_home_x if actual_true_zero_position_x is none else actual_true_zero_position_x, safe_home_y if actual_true_zero_position_y is none else actual_true_zero_position_y] %}
	{% endif %}
	
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	
	
	
	
	{% set X=[0, printable_x_max] %}
	{% endif %}
	
	
	{% set beacon_bed_mesh_scv = printer["gcode_macro RatOS"].beacon_bed_mesh_scv|default(25)|int %}
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% if printer.fastconfig.settings.beacon is defined and not beacon_contact_bed_mesh %}
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={beacon_bed_mesh_scv}
	{% endif %}
	
	
	{% set default_profile = printer["gcode_macro RatOS"].bed_mesh_profile|default('ratos') %}
	{% if printer["gcode_macro RatOS"].calibrate_bed_mesh|lower == 'true' %}
	BED_MESH_CLEAR
	{% if printer["gcode_macro RatOS"].adaptive_mesh|lower == 'true' %}
	CALIBRATE_ADAPTIVE_MESH PROFILE="{default_profile}" X0={X[0]} X1={X[1]} Y0={Y[0]} Y1={Y[1]} T={params.T|int} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={idex_mode} ZERO_REF_POS_X={zero_ref_pos[0]} ZERO_REF_POS_Y={zero_ref_pos[1]}
	{% else %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	BED_MESH_PROFILE LOAD="{default_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	
	{% elif printer["gcode_macro RatOS"].bed_mesh_profile is defined %}
	BED_MESH_CLEAR
	BED_MESH_PROFILE LOAD="{printer["gcode_macro RatOS"].bed_mesh_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"

[gcode_macro CALIBRATE_ADAPTIVE_MESH]
gcode = 
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set default_profile = params.PROFILE %}
	
	
	{% set x0 = params.X0|default(-1)|float %}
	{% set y0 = params.Y0|default(-1)|float %}
	{% set x1 = params.X1|default(-1)|float %}
	{% set y1 = params.Y1|default(-1)|float %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Received coordinates X0={x0|round(1)} Y0={y0|round(1)} X1={x1|round(1)} Y1={y1|round(1)}"
	
	{% if x0 >= x1 or y0 >= y1 %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Invalid coordinates received. Please check your slicer settings. Falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	
	
	{% if params.ZERO_REF_POS_X is defined and params.ZERO_REF_POS_Y is defined %}
	{% set zero_ref_pos_x = params.ZERO_REF_POS_X|float %}
	{% set zero_ref_pos_y = params.ZERO_REF_POS_Y|float %}
	{% if zero_ref_pos_x < x0 or zero_ref_pos_x > x1 or zero_ref_pos_y < y0 or zero_ref_pos_y > y1 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Zero reference position X={zero_ref_pos_x|round(1)} Y={zero_ref_pos_y|round(1)} is outside the mesh region, expanding mesh region to include it."
	{% set x0 = [x0, zero_ref_pos_x]|min %}
	{% set y0 = [y0, zero_ref_pos_y]|min %}
	{% set x1 = [x1, zero_ref_pos_x]|max %}
	{% set y1 = [y1, zero_ref_pos_y]|max %}
	{% endif %}
	{% endif %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float %}
	
	
	{% set mesh_x0 = [[x0, max_x]|min, min_x]|max %}
	{% set mesh_y0 = [[y0, max_y]|min, min_y]|max %}
	{% set mesh_x1 = [[x1, max_x]|min, min_x]|max %}
	{% set mesh_y1 = [[y1, max_y]|min, min_y]|max %}
	
	{% if mesh_x0 == min_x and mesh_y0 == min_y and mesh_x1 == max_x and mesh_y1 == max_y %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Print is using the full bed, falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	
	{% set probe_count_x = mesh_config.probe_count.split(",")[0]|int %}
	{% if mesh_config.probe_count.split(",")|length == 2 %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[1]|int %}
	{% else %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[0]|int %}
	{% endif %}
	
	
	{% set probe_x_step = (max_x - min_x) / probe_count_x %}
	{% set probe_y_step = (max_y - min_y) / probe_count_y %}
	
	
	{% set mesh_count_x = ([(mesh_x1 - mesh_x0) / probe_x_step, 3]|max)|int %}
	{% set mesh_count_y = ([(mesh_y1 - mesh_y0) / probe_y_step, 3]|max)|int %}
	{% set min_mesh_count = [mesh_count_x, mesh_count_y]|min %}
	{% set max_mesh_count = [mesh_count_x, mesh_count_y]|max %}
	
	
	{% set algorithm = mesh_config.algorithm %}
	{% if algorithm|lower == 'lagrange' and max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="cannot exceed a probe_count of 6 when using lagrange interpolation. Falling back to bicubic interpolation."
	{% set algorithm = 'bicubic' %}
	{% endif %}
	{% if algorithm|lower == 'bicubic' and min_mesh_count < 4 %}
	{% if max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="invalid probe_count option when using bicubic interpolation. Combination of 3 points on one axis with more than 6 on another is not permitted. Forcing minimum mesh count to be 4."
	{% set min_mesh_count = 4 %}
	{% else %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="bicubic interpolation with a probe_count of less than 4 points detected. Forcing lagrange interpolation."
	{% set algorithm = 'lagrange' %}
	{% endif %}
	{% endif %}
	
	{% set mesh_count_x = ([min_mesh_count, mesh_count_x]|max)|int %}
	{% set mesh_count_x = ([max_mesh_count, mesh_count_x]|min)|int %}
	{% set mesh_count_y = ([min_mesh_count, mesh_count_y]|max)|int %}
	{% set mesh_count_y = ([max_mesh_count, mesh_count_y]|min)|int %}
	
	{% set should_prime = printer["gcode_macro RatOS"].nozzle_priming == 'primeblob' %}
	{% if printer["dual_carriage"] is not defined %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% else %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 != 0 and probe_first %}
	{% set probe_first = false %}
	{% elif printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 == 0 and not probe_first %}
	{% set probe_first = true %}
	{% endif %}
	
	
	{% if should_prime and probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="mesh coordinates X0={mesh_x0|round(1)} Y0={mesh_y0|round(1)} X1={mesh_x1|round(1)} Y1={mesh_y1|round(1)}"
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y} RELATIVE_REFERENCE_INDEX=-1
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	
	
	{% if should_prime and not probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro M84]
rename_existing = M84.1
gcode = 
	
	M84.1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_OFFSET X=0 Y=0
	
	
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro _VAOC"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False
	{% endif %}
	
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	SET_SKEW CLEAR=1
	
	
	_LED_MOTORS_OFF

[gcode_macro M104]
rename_existing = M104.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M104" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set temperature_offset_t0 = printer["gcode_macro T0"].temperature_offset|default(0)|int %}
	{% set temperature_offset_t1 = printer["gcode_macro T1"].temperature_offset|default(0)|int %}
	{% set s0 = [s + temperature_offset_t0, 0]|max %}
	{% set s1 = [s + temperature_offset_t1, 0]|max %}
	{% if temperature_offset_t0 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t0}°C added to toolhead T0."
	{% endif %}
	{% if temperature_offset_t1 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t1}°C added to toolhead T1."
	{% endif %}
	{% else %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	M104.1 S{s0} T0
	M104.1 S{s1} T1
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% else %}
	M104.1 S{s} T{t}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M109]
rename_existing = M109.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M109" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M109" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	M109.1 S{s} T{t}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro SET_HEATER_TEMPERATURE]
rename_existing = SET_HEATER_TEMPERATURE_BASE
gcode = 
	
	{% set heater = params.HEATER|default("") %}
	{% set target = params.TARGET|default(0)|int %}
	
	DEBUG_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="heater: {heater}, target: {target}"
	
	{% set t = -1 %}
	{% if heater|lower == "extruder" or heater|lower == "extruder1" %}
	
	{% set t = 0 if heater|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and target > 0 %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set target = [target + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE_BASE HEATER="{heater}" TARGET={target}
	
	{% if t != -1 and printer.fastconfig.settings.beacon is defined %}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro TEMPERATURE_WAIT]
rename_existing = TEMPERATURE_WAIT_BASE
gcode = 
	
	{% set sensor = params.SENSOR|default("") %}
	{% set minimum = params.MINIMUM|default(-1)|int %}
	{% set maximum = params.MAXIMUM|default(-1)|int %}
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="sensor: {sensor}, minimum: {minimum}, maximum: {maximum}"
	
	{% set t = -1 %}
	{% if sensor|lower == "extruder" or sensor|lower == "extruder1" %}
	
	{% set t = 0 if sensor|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and (minimum > 0 or maximum > 0) %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% if minimum > -1 %}
	{% set minimum = [minimum + temperature_offset, 0]|max %}
	{% endif %}
	{% if maximum > -1 %}
	{% set maximum = [maximum + temperature_offset, 0]|max %}
	{% endif %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set id = "sensor " ~ sensor if t == -1 else "toolhead T" ~ t %}
	
	
	{% if minimum > -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum} MAXIMUM={maximum}
	{% elif minimum > -1 and maximum == -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum}
	{% elif minimum == -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MAXIMUM={maximum}
	{% else %}
	
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="neither MINIMUM or MAXIMUM args were specified, call TEMPERATURE_WAIT_BASE is expected to fail"
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}"
	{% endif %}
	
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature for {id} reached."

[gcode_macro SDCARD_PRINT_FILE]
rename_existing = SDCARD_PRINT_FILE_BASE
gcode = 
	{% if printer["ratos"] is defined %}
	PROCESS_GCODE_FILE { rawparams }
	{% else %}
	SDCARD_PRINT_FILE_BASE { rawparams }
	{% endif %}

[gcode_macro SKEW_PROFILE]
rename_existing = SKEW_PROFILE_BASE
variable_loaded_profile = ""
gcode = 
	{% if params.LOAD is defined %}
	{% if printer.fastconfig.settings["skew_correction %s" % params.LOAD] is defined %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='"{params.LOAD}"'
	{% endif %}
	{% endif %}
	
	SKEW_PROFILE_BASE { rawparams }

[gcode_macro SET_SKEW]
rename_existing = SET_SKEW_BASE
gcode = 
	{% if params.CLEAR is defined %}
	{% if params.CLEAR|default(0)|int == 1 %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='""'
	{% endif %}
	{% endif %}
	
	SET_SKEW_BASE { rawparams }

[gcode_macro SET_VELOCITY_LIMIT]
rename_existing = SET_VELOCITY_LIMIT_BASE
gcode = 
	{% if params.ACCEL_TO_DECEL is defined %}
	
	{% if params.ACCEL is defined %}
	{% set accel = params.ACCEL|float %}
	{% else %}
	{% set accel = printer.toolhead.max_accel|float %}
	{% endif %}
	
	{% if params.VELOCITY is defined %}
	{% set velocity = params.VELOCITY|float %}
	{% else %}
	{% set velocity = printer.toolhead.max_velocity|float %}
	{% endif %}
	
	{% if params.SQUARE_CORNER_VELOCITY is defined %}
	{% set scv = params.SQUARE_CORNER_VELOCITY|float %}
	{% else %}
	{% set scv = printer.toolhead.square_corner_velocity|float %}
	{% endif %}
	
	{% set mcr = params.ACCEL_TO_DECEL|float / accel %}
	
	DEBUG_ECHO PREFIX="SET_VELOCITY_LIMIT" MSG="ACCEL={accel}, VELOCITY={velocity}, SQUARE_CORNER_VELOCITY={scv}, MINIMUM_CRUISE_RATIO={mcr}"
	
	SET_VELOCITY_LIMIT_BASE ACCEL={accel} VELOCITY={velocity} SQUARE_CORNER_VELOCITY={scv} MINIMUM_CRUISE_RATIO={1-mcr}
	
	{% else %}
	
	SET_VELOCITY_LIMIT_BASE { rawparams }
	
	{% endif %}

[gcode_macro BED_MESH_CALIBRATE]
rename_existing = _BED_MESH_CALIBRATE_BASE
variable_abl_and_home_z_if_required = True
gcode = 
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	{% if abl_and_home_z_if_required %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% endif %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set beacon_default_probe_method = printer.fastconfig.settings.beacon.default_probe_method|default('proximity') %}
	{% set probe_method = params.PROBE_METHOD|default(beacon_default_probe_method)|lower %}
	{% if probe_method == 'proximity' %}
	_CHECK_ACTIVE_BEACON_MODEL_TEMP TITLE="Bed mesh calibration warning"
	{% endif %}
	{% endif %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_BED_MESH_CALIBRATE_BASE {rawparams}
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	_APPLY_RATOS_BED_MESH_PARAMETERS {rawparams}
	{% endif %}

[gcode_macro SET_GCODE_OFFSET]
rename_existing = SET_GCODE_OFFSET_BASE
gcode = 
	DEBUG_ECHO PREFIX="SET_GCODE_OFFSET" MSG="{rawparams|replace('"', '')|replace("'", '')}"
	{% set z_before = printer.gcode_move.homing_origin.z|float %}
	SET_GCODE_OFFSET_BASE {rawparams}
	_AFTER_SET_GCODE_OFFSET Z_BEFORE={z_before}

[gcode_macro _AFTER_SET_GCODE_OFFSET]
gcode = 
	{% set z_before = params.Z_BEFORE|float %}
	{% set z_after = printer.gcode_move.homing_origin.z|float %}
	{% if z_before != z_after %}
	_ALERT_NON_ZERO_Z_OFFSET FORCE=1
	{% endif %}

[gcode_macro _START_PRINT_PARK]
gcode = 
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_x = printer["gcode_macro RatOS"].start_print_park_x %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% if printer["gcode_macro RatOS"].start_print_park_x is defined and printer["gcode_macro RatOS"].start_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="start_print_park_x is ignored for IDEX printers"
	{% endif %}
	PARK_TOOLHEAD
	G90
	{% endif %}
	
	
	_PARK LOCATION={start_print_park_in} X={start_print_park_x}
	G0 Z{z} F{z_speed}

[gcode_macro _END_PRINT_PARK]
gcode = 
	{% if printer["dual_carriage"] is defined %}
	
	{% if printer["gcode_macro RatOS"].end_print_park_x is defined and printer["gcode_macro RatOS"].end_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="end_print_park_x is ignored for IDEX printers"
	{% endif %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	PARK_TOOLHEAD
	G90
	{% endif %}
	_PARK LOCATION={printer["gcode_macro RatOS"].end_print_park_in} X={printer["gcode_macro RatOS"].end_print_park_x}

[gcode_macro _PARK]
gcode = 
	
	{% set x = params.X %}
	{% set location = params.LOCATION|default('back')|lower %}
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	{% set nozzle_priming = printer["gcode_macro RatOS"].nozzle_priming|lower %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="park"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% if x != '' %}
	{% if x|float >= printer.toolhead.axis_minimum.x + 5 and x|float <= printable_x_max - 5 %}
	{% set park_x = x|float %}
	{% else %}
	{action_respond_info('The requested X co-ordinate is outside the defined axis bounds - using defaults')}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	{% else %}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	
	
	{% set park_y = printable_y_max - 15 %}
	{% if location == 'front' %}
	{% set park_y = printer.toolhead.axis_minimum.y + 5 %}
	{% elif location == 'center' %}
	{% set park_y = printable_y_max / 2 %}
	{% elif location == 'primeblob' and printer["dual_carriage"] is defined %}
	
	{% set park_y = printable_y_max - 15 %}
	{% endif %}
	
	
	{% if location == 'primeblob' and printer["dual_carriage"] is not defined %}
	{% if (nozzle_priming == 'primeblob' or nozzle_priming == 'primeline') %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set park_x = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set park_x = printable_x_max - 5 %}
	{% else %}
	{% set park_x = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set park_y = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set park_y = printable_y_max - 5 %}
	{% else %}
	{% set park_y = nozzle_prime_start_y|float %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	G0 X{park_x} Y{park_y} F{speed}
	{% else %}
	
	G0 Y{park_y} F{speed}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="park"

[gcode_macro SAVE_PROBE_RESULT]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	{% set last_z_offset = 9999.9 %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if beacon_contact_prime_probing %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	{% else %}
	{% set last_z_offset = printer.beacon.last_sample.dist - current_z %}
	{% endif %}
	{% elif printer.fastconfig.settings.bltouch is defined  %}
	{% set config_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% elif printer.fastconfig.settings.probe is defined  %}
	{% set config_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% endif %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Saving offset adjustment of {last_z_offset} in {params.VARIABLE|default('last_z_offset')}"
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={params.VARIABLE|default('last_z_offset')} VALUE={last_z_offset}

[gcode_macro PROBE_FOR_PRIMING]
gcode = 
	
	{% set probe_for_priming_disable_mesh_constraints = true if printer["gcode_macro RatOS"].probe_for_priming_disable_mesh_constraints|default(false)|lower == 'true' else false %}
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower != 'false' %}
	SAVE_GCODE_STATE NAME=probe_for_priming_state
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the prime location.."
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set t = params.TOOLHEAD|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% if idex_mode == '' %}
	
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% if t == 0 %}
	{% set x_start = 5 %}
	{% else %}
	{% set x_start = printable_x_max - 5 %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% endif %}
	{% endif %}
	{% set z = printer.fastconfig.settings.bed_mesh.horizontal_move_z|float %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% if printer.fastconfig.settings.bltouch is defined %}
	{% set x_offset = printer.fastconfig.settings.bltouch.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.bltouch.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% elif printer.fastconfig.settings.probe is defined %}
	{% set x_offset = printer.fastconfig.settings.probe.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.probe.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% elif printer.fastconfig.settings.beacon is defined %}
	{% set x_offset = printer.fastconfig.settings.beacon.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.beacon.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.beacon.trigger_distance|float %}
	{% else %}
	{ action_raise_error("No probe, beacon or bltouch section found. Adaptive priming only works with a [probe], [beacon] or [bltouch] section defined.") }
	{% endif %}
	
	{% if z < z_offset %}
	{ action_raise_error("Horizontal move Z ({z}) is below your probe's Z offset ({z_offset}). Please adjust your horizontal_move_z setting in [bed_mesh] to be above {z}.") }
	{% endif %}
	
	{% if not probe_for_priming_disable_mesh_constraints %}
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float - x_offset %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float - y_offset %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float - x_offset %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float - y_offset %}
	
	
	{% set x_start = [[x_start, max_x]|min, min_x]|max %}
	{% set y_start = [[y_start, max_y]|min, min_y]|max %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the start of the prime location at {x_start}, {y_start}"
	
	G90
	
	M83
	
	G0 Z{z} F{z_speed}
	
	G1 X{x_start} Y{y_start} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result
	{% endif %}
	
	{% if idex_mode == '' %}
	
	{% set x_end = x_start %}
	{% set y_end = y_start + 45 %}
	{% else %}
	
	{% if t==1 %}
	{% set x_end = x_start - 45 %}
	{% else %}
	{% set x_end = x_start + 45 %}
	{% endif %}
	{% set y_end = y_start %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the end of the prime location at {x_end}, {y_end}"
	G1 X{x_end} Y{y_end} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result
	{% endif %}
	
	RESTORE_GCODE_STATE NAME=probe_for_priming_state
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	{% endif %}

[gcode_macro RESET_PRIME_PROBE_STATE]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result VALUE=None
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result_t1 VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result_t1 VALUE=None
	{% endif %}

[gcode_macro PROBE_CURRENT_POSITION]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	SAVE_GCODE_STATE NAME=probe_current_position_state
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	ASSERT_PROBE_DEPLOYED
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_prime_probing %}
	PROBE PROBE_METHOD=contact SAMPLES=1
	{% else %}
	PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	BEACON_QUERY
	{% else %}
	
	RESTORE_GCODE_STATE NAME=probe_current_position_state MOVE=1 MOVE_SPEED={printer["gcode_macro RatOS"].macro_z_speed|float}
	{% endif %}

[gcode_macro PRIME_BLOB]
description = Prints a primeblob, used internally, if configured, as part of the START_PRINT macro.
variable_x_offset = 5
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="prime_blob"
	SET_MACRO_TRAVEL_SETTINGS
	
	RATOS_ECHO PREFIX="Priming" MSG="Priming nozzle with prime blob.."
	
	
	{% set current_toolhead = 0 %}
	
	
	{% set target_idex_mode = '' %}
	{% set extruder = 'extruder' %}
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE is defined %}
	{% set target_idex_mode = params.IDEX_MODE|default('')|lower %}
	{% else %}
	{ action_raise_error("IDEX_MODE parameter not found for PRIME_BLOB macro. This is likely a bug.") }
	{% endif %}
	RATOS_ECHO PREFIX="Priming" MSG="Priming in IDEX {target_idex_mode} mode.."
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set current_toolhead = 1 if current_idex_mode=='primary' else 0 %}
	{% set extruder = 'extruder1' if current_toolhead == 1 else 'extruder' %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	SAVE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set fan_speed = printer["gcode_macro RatOS"].nozzle_prime_bridge_fan|float %}
	{% set nozzle_diameter = printer.fastconfig.settings[extruder].nozzle_diameter|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set has_start_offset_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) != 9999.9 %}
	{% if printer["dual_carriage"] is defined %}
	{% set has_start_offset_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) != 9999.9 %}
	{% endif %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_z_height = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set nozzle_prime_direction = printer["gcode_macro RatOS"].nozzle_prime_direction|lower %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% if target_idex_mode == '' %}
	
	{% set x_factor = 0 %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% set y_factor = -1 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% if nozzle_prime_start_y|float < printable_y_max / 2 %}
	{% set y_factor = 1 %}
	{% else %}
	{% set y_factor = -1 %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_direction == 'forwards' %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_direction == 'backwards' %}
	{% set y_factor = -1 %}
	{% endif %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% else %}
	{% set z = start_print_park_z_height %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% set y_factor = 0 %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set x_start = center_x / 2 + 5 %}
	{% set x_factor = 1 %}
	{% else %}
	
	
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% if current_toolhead == 0 %}
	{% set x_start = 55 %}
	{% set x_factor = -1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 55 %}
	{% set x_factor = 1 %}
	{% endif %}
	{% else %}
	{% if current_toolhead == 0 %}
	{% set x_start = 5 %}
	{% set x_factor = 1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 5 %}
	{% set x_factor = -1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_x_max - 5 %}
	{% endif %}
	{% set z = 10 %}
	{% endif %}
	
	{% set start_z_offset = 0 %}
	{% set end_z_offset = 0 %}
	{% if has_start_offset_t0 %}
	{% set start_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) %}
	{% set end_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_end_result|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t0) ) }
	{% endif %}
	{% if end_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t0) )  }
	{% endif %}
	{% set start_z_offset = start_z_probe_result_t0 %}
	{% set end_z_offset = end_z_probe_result_t0 %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	{% if current_toolhead == 1 or both_toolheads or target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	{% if has_start_offset_t1 %}
	{% set start_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) %}
	{% set end_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_end_result_t1|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t1) ) }
	{% endif %}
	{% if end_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t1) ) }
	{% endif %}
	{% set start_z_offset = [start_z_offset, start_z_probe_result_t1]|max %}
	{% set end_z_offset = [end_z_offset, start_z_probe_result_t1]|max %}
	{% endif %}
	{% endif %}
	{% if target_idex_mode != 'copy' and target_idex_mode != 'mirror' %}
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% set original_start_z_offset = start_z_offset %}
	{% set original_end_z_offset = end_z_offset %}
	{% set start_z_offset = original_end_z_offset %}
	{% set end_z_offset = original_start_z_offset %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	DEBUG_ECHO PREFIX="PRIME_BLOB" MSG="x_start: {x_start}, y_start: {y_start}, x_factor: {x_factor}, y_factor: {y_factor}, z: {z}, start_z_offset: {start_z_offset}, end_z_offset: {end_z_offset}"
	
	
	G90
	
	M83
	RATOS_ECHO PREFIX="Priming" MSG="Lifting Z to {z}.."
	
	G0 Z{z} F{z_speed}
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% if start_print_park_in != 'primeblob' %}
	G1 X{x_start} F{speed}
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% endif %}
	{% else %}
	
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% if target_idex_mode=="copy" or target_idex_mode=="mirror" %}
	RATOS_ECHO PREFIX="Priming" MSG="Mirroring move to {x_start}, {y_start} along the edge of the print area.."
	
	_IDEX_MIRROR PRIMING=1
	{% else %}
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% endif %}
	G1 X{x_start} F{speed}
	{% endif %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Starting prime blob.."
	
	G1 Z{0.5 + start_z_offset} F{z_speed}
	
	G1 Y{y_start} F{speed}
	
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	
	M106 S{fan_speed}
	
	G1 Z5 F100 E5
	G92 E0
	RATOS_ECHO PREFIX="Priming" MSG="Bridging with {((fan_speed/255) * 100)|int}% fan speed.."
	
	G1 F3000 X{x_start + (15 * x_factor)} Y{y_start + (15 * y_factor)} E{1 / ((0.4 / nozzle_diameter) ** 2)}
	
	
	
	G1 F3000 X{x_start + (20 * x_factor)} Y{y_start + (20 * y_factor)} Z{3.8 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (34 * x_factor)} Y{y_start + (34 * y_factor)} Z{2.6 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (38 * x_factor)} Y{y_start + (38 * y_factor)} Z{1.4 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (42 * x_factor)} Y{y_start + (42 * y_factor)} Z{0.2 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	
	M106 S0
	
	G1 F3000 X{x_start + (46 * x_factor)} Y{y_start + (46 * y_factor)} Z{0.2 + end_z_offset} E0.6
	
	G1 F{speed} X{x_start + (50 * x_factor)} Y{y_start + (50 * y_factor)}
	
	
	{% if target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if target_idex_mode == "copy" %}
	{% if first_y >= 0 %}
	_IDEX_COPY DANCE=0 Y={first_y}
	{% else %}
	_IDEX_COPY DANCE=0 Y={params.Y1}
	{% endif %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	RESTORE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="prime_blob"
	
	
	G92 E0

[gcode_macro UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set temp = params.TEMP|default(220)|int %}
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_UNLOAD_FILAMENT TEMP={temp} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_UNLOAD_FILAMENT]
description = Unload filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_UNLOAD_FILAMENT" MSG="TEMP: {temp}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=unload_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	G4 P3000
	
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD=0 NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=unload_state
	
	
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament unloading completed"

[gcode_macro _IDEX_UNLOAD_FILAMENT]
description = Unload filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading T{toolhead} filament..."
	
	DEBUG_ECHO PREFIX="_IDEX_UNLOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} AUTOMATED={automated}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="T{toolhead} filament unloading completed"

[gcode_macro _UNLOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LEGACY_UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
gcode = 
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set unload_speed = 5 * 60 %}
	{% set unload_length = printer["gcode_macro RatOS"].filament_unload_length|float %}
	M117 Unloading filament...
	
	G0 E10 F300
	
	G0 E-5 F3600
	
	G4 P3000
	
	G0 E5 F6000
	
	G0 E-15 F6000
	
	G0 E-{unload_length} F{unload_speed}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}
	M117 Filament unloaded!
	RESPOND MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	RATOS_ECHO MSG="Unloading filament from nozzle to cooling zone... Please wait!"
	
	_PURGE_BEFORE_UNLOAD TOOLHEAD={toolhead}
	
	{% if printer["gcode_macro _UNLOAD_WITHOUT_TIP_FORMING"] is defined %}
	
	_UNLOAD_WITHOUT_TIP_FORMING TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	_UNLOAD_WITH_TIP_FORMING NAME='{filament_name}' TYPE='{filament_type}'
	{% endif %}
	
	G4 P3000

[gcode_macro _UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	{% set tooolhead_sensor_to_extruder_gear_distance = printer["gcode_macro T%s" % toolhead].tooolhead_sensor_to_extruder_gear_distance|float %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER" MSG="TOOLHEAD: {toolhead}"
	
	
	G0 E-{extruder_gear_to_cooling_position_distance + tooolhead_sensor_to_extruder_gear_distance + 50} F{extruder_load_speed}
	
	RATOS_ECHO MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_WITH_TIP_FORMING]
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	{% if filament_name != '' and filament_type != '' %}
	_UNLOAD_KNOWN_FILAMENT NAME={filament_name} TYPE={filament_type}
	{% else %}
	_UNLOAD_UNKNOWN_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _UNLOAD_KNOWN_FILAMENT]
description = User overrideable tip forming macro if slicer filament profiles are known
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	RATOS_ECHO PREFIX="FILAMENT TYPE" MSG='{filament_type}'
	RATOS_ECHO PREFIX="FILAMENT PROFILE" MSG='{filament_name}'
	
	
	{% if filament_name == "Prusament PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% elif filament_name == "Nobufil PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% else %}
	
	RATOS_ECHO PREFIX="_UNLOAD_KNOWN_FILAMENT" MSG="Filament profile not found!"
	_UNLOAD_UNKNOWN_FILAMENT
	{% endif %}

[gcode_macro _UNLOAD_UNKNOWN_FILAMENT]
description = User overrideable standard tip forming macro
gcode = 
	
	DEBUG_ECHO PREFIX="_UNLOAD_UNKNOWN_FILAMENT" MSG="Using standard tip forming macro!"
	
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10

[gcode_macro _TIP_FORMING]
gcode = 
	
	{% set cooling_moves = params.COOLING_MOVES|default(4)|int %}
	{% set cooling_move_length = params.COOLING_MOVE_LENGTH|default(10)|float %}
	{% set start_cooling_speed = params.START_COOLING_SPEED|default(10)|float * 60 %}
	{% set end_cooling_speed = params.END_COOLING_SPEED|default(50)|float * 60 %}
	{% if cooling_moves == 0 %}
	{% set cooling_move_length = 0 %}
	{% endif %}
	
	
	{% set dip = true if params.DIP|default(false)|lower == "true" else false %}
	{% set dip_length = params.DIP_LENGTH|default(22)|float %}
	{% set dip_speed = params.DIP_SPEED|default(30)|float * 60 %}
	{% set dip_retract_speed = params.DIP_RETRACT_SPEED|default(70)|float * 60 %}
	
	
	{% set retract_length = params.RETRACT_LENGTH|default(18)|float %}
	{% set start_retract_speed = params.START_RETRACT_SPEED|default(120)|float * 60 %}
	{% set end_retract_speed = params.END_RETRACT_SPEED|default(20)|float * 60 %}
	
	DEBUG_ECHO PREFIX="_TIP_FORMING" MSG="cooling_moves: {cooling_moves}, cooling_move_length: {cooling_move_length}, start_cooling_speed: {start_cooling_speed}, end_cooling_speed: {end_cooling_speed}, dip: {dip}, dip_length: {dip_length}, dip_speed: {dip_speed}, dip_retract_speed: {dip_retract_speed}, retract_length: {retract_length}, start_retract_speed: {start_retract_speed}, end_retract_speed: {end_retract_speed}"
	
	M220 S100
	
	
	G92 E0
	{% set retract = retract_length + cooling_move_length / 2 - 15 %}
	G1 E-15 F{start_retract_speed}
	G1 E-{0.7 * retract} F{1.0 * end_retract_speed}
	G1 E-{0.2 * retract} F{0.5 * end_retract_speed}
	G1 E-{0.1 * retract} F{0.3 * end_retract_speed}
	
	
	G92 E0
	{% if cooling_moves > 0 %}
	{% set i = (end_cooling_speed - start_cooling_speed) / (2 * cooling_moves - 1) %}
	{% for m in range(cooling_moves) %}
	G1 E{cooling_move_length} F{(start_cooling_speed + i * m * 2)}
	G1 E-{cooling_move_length} F{(start_cooling_speed + i * (m * 2 + 1))}
	{% endfor %}
	{% endif %}
	
	
	G92 E0
	{% if dip %}
	G1 E{dip_length} F{dip_speed}
	G4 P100
	G1 E-{dip_length} F{dip_retract_speed}
	{% endif %}
	
	G92 E0
	M400

[delayed_gcode __ON_FILAMENT_SENSOR_BUTTON_PRESSED_STARTUP_GUARD]
initial_duration = 2.
gcode = 
	SET_GCODE_VARIABLE MACRO=_ON_FILAMENT_SENSOR_BUTTON_PRESSED VARIABLE=startup_complete VALUE=True

[gcode_macro _ON_FILAMENT_SENSOR_BUTTON_PRESSED]
variable_startup_complete = False
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set toolhead_sensor_button_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_sensor_button_only_when_sensor_enabled|default(false)|lower == 'true' %}
	
	
	{% if not startup_complete and sensor_enabled %}
	{action_emergency_stop("RatOS: The T%s filament sensor button was triggered immediately on printer startup. This is likely a false trigger. Please check your filament sensor wiring and configuration!" % (toolhead,))}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_SENSOR_BUTTON_PRESSED" MSG="TOOLHEAD: {toolhead}, SENSOR_ENABLED: {sensor_enabled}, TOOLHEAD_SENSOR_BUTTON_ONLY_WHEN_SENSOR_ENABLED: {toolhead_sensor_button_only_when_sensor_enabled}"
	
	{% if not printer.virtual_sdcard.is_active and (sensor_enabled or not toolhead_sensor_button_only_when_sensor_enabled) %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	{% set toolhead_detect_clog_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_detect_clog_only_when_sensor_enabled|default(true)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}, ENABLE_CLOG_DETECTION: {enable_clog_detection}, TOOLHEAD_DETECT_CLOG_ONLY_WHEN_SENSOR_ENABLED: {toolhead_detect_clog_only_when_sensor_enabled}, SENSOR_ENABLED: {sensor_enabled}"
	
	{% if enable_clog_detection and (sensor_enabled or not toolhead_detect_clog_only_when_sensor_enabled) %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_clog_detection %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_FILAMENT_END]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set clogged = true if params.CLOGGED|default(false)|lower == 'true' else false %}
	
	
	{% set unload_after_runout = printer["gcode_macro T%s" % toolhead].unload_after_runout|float %}
	
	
	{% if clogged %}
	_LED_FILAMENT_CLOG TOOLHEAD={toolhead}
	{% else %}
	_LED_FILAMENT_RUNOUT TOOLHEAD={toolhead}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_END" MSG="TOOLHEAD: {toolhead}"
	
	{% if printer.virtual_sdcard.is_active %}
	{% if not printer.pause_resume.is_paused %}
	PAUSE RUNOUT=True
	{% endif %}
	{% if not clogged and unload_after_runout %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	{% if not clogged and printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true'%}
	_JOIN_SPOOL TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M600]
description = Executes a color change by pausing the printer an unloading the filament.
gcode = 
	PAUSE
	UNLOAD_FILAMENT AUTOMATED=True
	RATOS_ECHO MSG="Please load new filament and resume"

[gcode_macro COLD_PULL]
description = Automated hotend cold pull.
gcode = 
	
	{% set extrusion_temp = params.EXTRUSION_TEMP|default(220)|int %}
	{% set cold_pull_temp = params.COLD_PULL_TEMP|default(80)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	
	{% if printer["dual_carriage"] is not defined %}
	{% set toolhead = 0 %}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead != 0 and toolhead != 1 %}
	{action_raise_error("Please select toolhead! 0 = left, 1 = right toolhead")}
	{% endif %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	RATOS_ECHO MSG="Starting cold pull on T{toolhead}..."
	{% else %}
	RATOS_ECHO MSG="Starting cold pull..."
	{% endif %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	SAVE_GCODE_STATE NAME=cold_pull_state
	
	
	{% if printer["dual_carriage"] is defined and "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	RATOS_ECHO MSG="Heating T{toolhead} to {extrusion_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={extrusion_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={extrusion_temp} MAXIMUM={extrusion_temp + 2}
	
	
	G4 P3000
	
	
	RATOS_ECHO MSG="extruding..."
	G92 E0
	G1 E30 F300
	G92 E0
	
	
	RATOS_ECHO MSG="Cooling T{toolhead} to {cold_pull_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={cold_pull_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={cold_pull_temp} MAXIMUM={cold_pull_temp + 2}
	
	
	G4 P10000
	
	
	RATOS_ECHO MSG="cold pull..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-40 VELOCITY=5 ACCEL=100
	
	
	RATOS_ECHO MSG="eject filament..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-200 VELOCITY=20 ACCEL=500
	
	
	RATOS_ECHO MSG="cooling down extruder..."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	RESTORE_GCODE_STATE NAME=cold_pull_state
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	
	CONSOLE_ECHO TITLE="Cold pull complete" MSG="Please remove the filament from the PTFE tube and cut the end off. Do NOT try to load it again." TYPE="warning"

[gcode_macro _USER_START_PRINT_BEFORE_HOMING]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_BED]
gcode = 

[gcode_macro _USER_START_PRINT_BED_MESH]
gcode = 

[gcode_macro _USER_START_PRINT_PARK]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 

[gcode_macro _USER_START_PRINT_HEAT_CHAMBER]
description = Uses the extruder sensor to wait for chamber temp. Override the _START_PRINT_HEAT_CHAMBER macro to implement heated chamber handling.
gcode = 
	
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}

[gcode_macro _USER_END_PRINT_BEFORE_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_AFTER_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_PARK]
gcode = 

[gcode_macro _USER_END_PRINT_FINISHED]
description = User hook for when the print is finished after gcode state has been restored.
gcode = 

[gcode_macro _USER_START_PRINT]
gcode = 

[gcode_macro _USER_END_START_PRINT]
gcode = 

[gcode_macro _USER_START_FEATURE]
gcode = 

[gcode_macro _USER_END_FEATURE]
gcode = 

[gcode_macro _USER_BEFORE_IDLE_TIMEOUT]
gcode = 

[gcode_macro _USER_AFTER_IDLE_TIMEOUT]
gcode = 

[gcode_macro ECHO_T_VARS]
description = Echo Toolhead variables to the console.
gcode = 
	{% set t = params.T|default(0) %}
	RATOS_ECHO MSG="T{t} Variables"
	{% for var, value in printer["gcode_macro T%s" % t].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ECHO_RATOS_VARS]
description = Echo RatOS variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro RatOS"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ENSURE_CRITICAL_RATOS_INIT]
variable_completed = False
gcode = 
	{% if not completed %}
	CALCULATE_PRINTABLE_AREA
	SET_GCODE_VARIABLE MACRO=ENSURE_CRITICAL_RATOS_INIT VARIABLE=completed VALUE=True
	{% endif %}

[delayed_gcode RATOS_INIT]
initial_duration = 0.1
gcode = 
	{action_respond_info("Initializing RatOS...")}
	ENSURE_CRITICAL_RATOS_INIT
	_LED_STANDBY
	INITIAL_FRONTEND_UPDATE
	_CHAMBER_FILTER_SANITY_CHECK
	{% if printer.fastconfig.settings.beacon is defined %}
	
	_BED_MESH_SANITY_CHECK
	{% endif %}
	{% set svv = printer.save_variables.variables %}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=0 C={svv.nozzle_expansion_coefficient_t0|default(0.06)|float}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=1 C={svv.nozzle_expansion_coefficient_t1|default(0.06)|float}
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=idex_applied_offset

[delayed_gcode RATOS_LOGO]
initial_duration = 2
gcode = 
	
	
	
	
	
	ENSURE_CRITICAL_RATOS_INIT
	HELLO_RATOS
	_ALERT_NON_ZERO_Z_OFFSET

[gcode_macro _ALERT_NON_ZERO_Z_OFFSET]
gcode = 
	{% set force = params.FORCE|default(0)|int == 1 %}
	{% set user_offset = printer.named_offsets.user_probe_z_offset.z|float %}
	{% set gcode_offset = printer.gcode_move.homing_origin.z|float %}
	{% set combined_offset = user_offset + gcode_offset %}
	
	{% if force or user_offset != 0 or gcode_offset != 0 %}
	{% set title = "User-adjusted Z-offset of %.3f mm is active" % combined_offset %}
	{% set msg = "" %}
	{% set nl = "" %}
	{% if user_offset != 0 %}
	{% set msg = msg + "beacon true zero user Z-offset: %.3f mm (to clear, use Z_OFFSET_APPLY_PROBE CLEAR=1)" % user_offset %}
	{% set nl = "_N_" %}
	{% endif %}
	{% if gcode_offset != 0 %}
	{% set msg = msg + nl + "G-code Z-offset: %.3f mm" % gcode_offset %}
	{% endif %}
	CONSOLE_ECHO TITLE="{title}" TYPE="info" MSG="{msg}"
	{% endif %}

[gcode_macro _INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE]
gcode = 
	{% set variable = params.VARIABLE|string %}
	{% set svv = printer.save_variables.variables %}
	{% set nlu_msg = "no longer used, please remove" %}
	{% if svv[variable] is defined %}
	{% set v = svv[variable]|string|replace('"', '')|replace("'", "") %}
	{% if not nlu_msg in v %}
	SAVE_VARIABLE VARIABLE={variable} VALUE='"{nlu_msg} (was {v})"'
	{% endif %}
	CONSOLE_ECHO TITLE="Deprecated ratos-variables.cfg variable" TYPE="warning" MSG="The variable {variable} is no longer used, please remove it from your ratos-variables.cfg file."
	{% endif %}

[gcode_macro _NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK]
gcode = 
	
	
	
	
	
	
	
	{% set t = params.T|int %}
	{% set c = params.C|float %}
	{% set normal_low = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_low|default(0.05)|float %}
	{% set normal_high = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_high|default(0.10)|float %}
	
	{% if c < 0 %}
	
	{action_emergency_stop("Invalid nozzle_expansion_coefficient_t%s value in ratos-variables.cfg: %.3f. It must be non-negative." % (t, c))}
	{% endif %}
	{% if c >= normal_high %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite high. Please verify that this is correct."
	{% endif %}
	{% if c <= normal_low %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite low. Please verify that this is correct."
	{% endif %}

[gcode_macro INITIAL_FRONTEND_UPDATE]
gcode = 
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_error = printer["gcode_macro RatOS"].status_color_error|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_unknown}"'
	{% endif %}
	
	
	{% set t0_sensor = "undefined" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	{% set t0_sensor = "detected" %}
	{% else %}
	{% set t0_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t0_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	{% set t1_sensor = "undefined" %}
	{% if printer["dual_carriage"] is defined and printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	{% set t1_sensor = "detected" %}
	{% else %}
	{% set t1_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t1_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	{% if svv.t0_filament is defined and printer["gcode_macro T0"] is defined %}
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	{% if t0_sensor != "empty" %}
	{% set t0_filament_type = svv.t0_filament[0]|default('')|string %}
	{% set t0_filament_name = svv.t0_filament[1]|default('')|string %}
	{% set t0_filament_temp = svv.t0_filament[2]|default(0)|float %}
	{% if t0_filament_name != '' and t0_filament_type != '' and t0_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{t0_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{t0_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={t0_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}
	{% if svv.t1_filament is defined and printer["gcode_macro T1"] is defined %}
	{% if printer["gcode_macro T1"].filament_name is defined and printer["gcode_macro T1"].filament_type is defined and printer["gcode_macro T1"].filament_temp is defined %}
	{% if t1_sensor != "empty" %}
	{% set t1_filament_type = svv.t1_filament[0]|default('')|string %}
	{% set t1_filament_name = svv.t1_filament[1]|default('')|string %}
	{% set t1_filament_temp = svv.t1_filament[2]|default(0)|float %}
	{% if t1_filament_name != '' and t1_filament_type != '' and t1_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='"{t1_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='"{t1_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE={t1_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t1_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro CALCULATE_PRINTABLE_AREA]
variable_calculated = False
gcode = 
	{% if not calculated %}
	{% set bed_margin_x = printer["gcode_macro RatOS"].bed_margin_x %}
	{% set bed_margin_y = printer["gcode_macro RatOS"].bed_margin_y %}
	
	
	
	{% set tool = 0 if printer["gcode_macro T0"] is not defined or printer["gcode_macro T0"].active else 1 %}
	{% set max_x = printer.toolhead.axis_maximum.x if printer["dual_carriage"] is defined and tool == 0 else printer.toolhead.axis_maximum.x - bed_margin_x[1] %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	
	
	{% set max_x = printer.toolhead.axis_maximum.x %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="printer.toolhead.axis_maximum.x {printer.toolhead.axis_maximum.x}"
	
	{% set max_y = printer.toolhead.axis_maximum.y - bed_margin_y[1]%}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_x_max VALUE={max_x}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_y_max VALUE={max_y}
	SET_GCODE_VARIABLE MACRO=CALCULATE_PRINTABLE_AREA VARIABLE=calculated VALUE=True
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	RATOS_LOG PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	{% endif %}

[gcode_macro CACHE_TOOLHEAD_SETTINGS]
variable_cache = {"global": {"accel": 1000, "ratio": 0.5, "speed": 50, "scv": 5}}
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set dummy = cache.__setitem__(key, {"accel": printer.toolhead.max_accel, "ratio": printer.toolhead.minimum_cruise_ratio, "speed": printer.toolhead.max_velocity, "scv": printer.toolhead.square_corner_velocity}) %}
	SET_GCODE_VARIABLE MACRO=CACHE_TOOLHEAD_SETTINGS VARIABLE=cache VALUE="{cache | pprint | replace("\n", "") | replace("\"", "\\\"")}"
	DEBUG_ECHO PREFIX="CACHE_TOOLHEAD_SETTINGS" MSG="Toolhead settings cached for {key}. {printer.toolhead.max_accel} accel, {printer.toolhead.minimum_cruise_ratio} ratio, {printer.toolhead.max_velocity} velocity, {printer.toolhead.square_corner_velocity} scv."

[gcode_macro RESTORE_TOOLHEAD_SETTINGS]
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set values = printer["gcode_macro CACHE_TOOLHEAD_SETTINGS"].cache.__getitem__(key) %}
	{% if values is not defined or values == 'None' %}
	{ action_raise_error("RESTORE_TOOLHEAD_SETTINGS: Toolhead settings not cached for key '" ~ key ~ "'.") }
	{% endif %}
	SET_VELOCITY_LIMIT ACCEL={values.accel} MINIMUM_CRUISE_RATIO={values.ratio} VELOCITY={values.speed} SQUARE_CORNER_VELOCITY={values.scv}
	DEBUG_ECHO PREFIX="RESTORE_TOOLHEAD_SETTINGS" MSG="Toolhead settings restored. {values.accel} accel, {values.ratio} ratio, {values.speed} velocity, {values.scv} scv."

[gcode_macro SET_MACRO_TRAVEL_SETTINGS]
gcode = 
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float %}
	{% set accel = printer["gcode_macro RatOS"].macro_travel_accel %}
	SET_VELOCITY_LIMIT ACCEL={accel} MINIMUM_CRUISE_RATIO=0.5 VELOCITY={speed} SQUARE_CORNER_VELOCITY={5}
	DEBUG_ECHO PREFIX="SET_MACRO_TRAVEL_SETTINGS" MSG="Macro travel settings set. {accel} accel, {speed} velocity"

[gcode_macro SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% if printer["dual_carriage"] is not defined %}
	
	SET_KINEMATIC_POSITION X={printable_x_max / 2} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	{% else %}
	
	IDEX_SET_CENTER_KINEMATIC_POSITION
	{% endif %}

[gcode_macro IDEX_SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x - (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x + (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY

[gcode_macro VERIFY_HYBRID_INVERTED]
gcode = 
	
	{% set inverted = False %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy is defined and printer.fastconfig.settings.ratos_hybrid_corexy.inverted is defined %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy.inverted|lower == 'true' %}
	{% set inverted = True %}
	{% endif %}
	{% endif %}
	{% if inverted == False %}
	{ action_emergency_stop("ratos_hybrid_corexy NOT INVERTED! Inverted hybrid core-xy bugfix not detected.") }
	{% endif %}

[gcode_macro RATOS_ECHO]
gcode = 
	{% set prefix = "RatOS" %}
	{% set debug = params.DEBUG|default(0)|int %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " | " ~ params.PREFIX %}
	{% endif %}
	{% set prefix = prefix ~ ":" %}
	{% set msg = "" %}
	{% if params.MSG is defined %}
	{% set msg = params.MSG %}
	{% else %}
	{% set msg = "No msg parameter provided (this is a bug or unintended use)." %}
	{% endif %}
	{% if not debug %}
	
	M117 {prefix} {msg}
	{% endif %}
	RATOS_LOG PREFIX="{prefix}" MSG="{msg}"
	{% if not debug %}
	RESPOND PREFIX="{prefix}" MSG="{msg}"
	{% else %}
	CONSOLE_ECHO TITLE="{prefix}" TYPE="debug" MSG="{msg}"
	{% endif %}

[gcode_macro ENABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=True
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=prefix_filter VALUE="'{params.FILTER|default('')|lower}'"
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging enabled."

[gcode_macro DISABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=False
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging disabled."

[gcode_macro DEBUG_ECHO]
variable_enabled = False
variable_prefix_filter = ''
gcode = 
	{% set prefix = "DEBUG" %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " - " ~ params.PREFIX %}
	{% endif %}
	{% if enabled and (prefix_filter|lower == '' or prefix_filter|lower in params.PREFIX|lower) %}
	RATOS_ECHO PREFIX="{prefix}" MSG="{params.MSG}" DEBUG=1
	{% endif %}

[gcode_macro START_FEATURE]
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="Start {params.FEATURE} feature gcode"
	{% set scv = printer.toolhead.square_corner_velocity|int|default(5) %}
	{% set accel = printer.toolhead.max_accel|int|default(10000) %}
	{% set ratio = printer.toolhead.minimum_cruise_ratio|float|default(0.5) %}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="scv" VALUE={scv}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="accel" VALUE={accel}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="ratio" VALUE={ratio}
	_USER_START_FEATURE FEATURE="{params.FEATURE}"

[gcode_macro END_FEATURE]
variable_scv = 5
variable_accel = 10000
variable_ratio = 0.5
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="End {params.FEATURE} feature gcode"
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={scv} ACCEL={accel} MINIMUM_CRUISE_RATIO={ratio}
	_USER_END_FEATURE FEATURE="{params.FEATURE}" SCV={scv} ACCEL={accel} RATIO={ratio}

[gcode_macro _ON_LAYER_CHANGE]
variable_layer_number = 0
description = INTERNAL USE ONLY. Call it from the slicers after layer change custom gcode
gcode = 
	
	{% set layer = params.LAYER|int %}
	
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE={layer}
	SET_PRINT_STATS_INFO CURRENT_LAYER={layer}

[gcode_macro _LEARN_MORE_CALIBRATION]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/calibration" %}
	{% set link_text = "RatOS Calibration Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_CHAMBER_FILTER]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter Control" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_FILAMENT]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/filaments" %}
	{% set link_text = "RatOS Filament Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _CONSOLE_SAVE_CONFIG]
gcode = 
	M118 Click <a class="command text--blue">SAVE_CONFIG</a> to save the settings to your printer.cfg.

[gcode_macro _LOAD_RATOS_SKEW_PROFILE]
gcode = 
	{% set ratos_skew_profile = printer["gcode_macro RatOS"].skew_profile|default("") %}
	{% if ratos_skew_profile != "" %}
	{% if printer.fastconfig.config["skew_correction %s" % ratos_skew_profile] is defined %}
	SKEW_PROFILE LOAD={ratos_skew_profile}
	GET_CURRENT_SKEW
	{% else %}
	{% set line_1 = '"Could not find skew profile %s!_N_Clearing skew correction."' % ratos_skew_profile %}
	CONSOLE_ECHO TITLE="Missing skew profile!" TYPE="warning" MSG={line_1}
	SET_SKEW CLEAR=1
	{% endif %}
	{% endif %}

[gcode_macro M601]
gcode = 
	PAUSE

[gcode_macro _STOP_AND_RAISE_ERROR]
gcode = 
	M84
	_RAISE_ERROR MSG="{params.MSG}"

[gcode_macro _RESET_GCODE_VARIABLES]
description = Reset specified [gcode_macro ...] variables to their original values from configuration when Klipper started.
	- MACRO: Name of the GCODE macro containing the variables to reset.
	- VARIABLES: Comma-separated list of variable names to reset (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- QUIET: (optional) If true, suppresses console echo messages for each reset variable. Default is false.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set quiet = params.QUIET|default("false")|lower in ("true", "1", "yes") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	{% set settings = printer.fastconfig.settings[obj_name|lower] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro %s]" % macro) }
	{% endif %}
	
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if settings["variable_%s" % var] is not defined %}
	{ action_raise_error("Variable '%s' is not defined in settings for [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	
	{% for var in vars %}
	{% set var_value = obj[var] %}
	{% if var_value is defined %}
	{% set v = settings["variable_%s" % var] %}
	{% if v != var_value|string %}
	{% if var_value is string %}
	{% set v = '"\'' ~ v|replace('"', '\\"')|replace("'", "\\'") ~ '\'"' %}
	{% endif %}
	SET_GCODE_VARIABLE MACRO={macro} VARIABLE={var} VALUE={v}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Reset {macro} variable {var} to original value: {v} (was {obj[var]})"
	{% endif %}
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro _SHOW_GCODE_VARIABLES]
description = Show current values of specified [gcode_macro ...] variables.
	- MACRO: Name of the GCODE macro containing the variables to show.
	- VARIABLES: Comma-separated list of variable names to show (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- PAD: (optional) If defined, provide a single character to use for padding variable names to align values in a tabular format in the console output. Default is no padding.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set pad = params.PAD|default("") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	
	{% set ns = namespace() %}
	{% set ns.max_len = 0 %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% set ns.max_len = (ns.max_len, var|length)|max %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if pad %}
	{% set padding = pad * (ns.max_len - var|length) %}
	CONSOLE_ECHO MSG="{var}{padding} {obj[var]}"
	{% else %}
	CONSOLE_ECHO MSG="{var}: {obj[var]}"
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro PAUSE]
description = Pauses the print
rename_existing = PAUSE_BASE
variable_extrude = 1.5
variable_retract = 1.5
variable_fan_speed = 0
variable_idex_mode = ""
variable_idex_toolhead = 0
variable_idex_toolhead_x = 0.0
variable_idex_toolhead_y = 0.0
variable_idex_toolhead_z = 0.0
gcode = 
	RATOS_ECHO MSG="Pausing print..."
	
	
	{% set runout_detected = true if params.RUNOUT|default(false)|lower == 'true' else false %}
	
	
	_LED_PAUSE
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	SAVE_GCODE_STATE NAME=PAUSE_state
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_mode VALUE='"{idex_mode}"'
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={idex_toolhead}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_x VALUE={printer.gcode_move.gcode_position.x|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_y VALUE={printer.gcode_move.gcode_position.y|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_z VALUE={printer.gcode_move.gcode_position.z|float}
	DEBUG_ECHO PREFIX="PAUSE" MSG="idex_mode: {idex_mode}, idex_toolhead: {idex_toolhead}, idex_toolhead_x: {idex_toolhead_x}, idex_toolhead_y: {idex_toolhead_y}, idex_toolhead_z: {idex_toolhead_z}"
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="pause"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if current_z < (max_z - 20.0) %}
	{% set z_safe = 20.0 %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	PAUSE_BASE
	
	
	{% if printer["dual_carriage"] is not defined %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan"].speed|float}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	{% if idex_toolhead == 0 %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t1"].speed|float}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106 S0
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set R = printer["gcode_macro PAUSE"].retract|float %}
	{% if can_extrude %}
	G91
	G1 E-{R} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	{% set pause_print_park_x = printer["gcode_macro RatOS"].pause_print_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].pause_print_park_in %}
	{% if runout_detected %}
	{% set pause_print_park_x = printer["gcode_macro RatOS"].runout_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].runout_park_in %}
	{% endif %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	DEBUG_ECHO PREFIX="PAUSE" MSG="z_speed: {z_speed}, pause_print_park_x: {pause_print_park_x}, pause_print_park_in: {pause_print_park_in}, default_toolhead: {default_toolhead}"
	{% if "xyz" in printer.toolhead.homed_axes %}
	G91
	G1 Z{z_safe} F{z_speed}
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% else %}
	
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	_IDEX_SINGLE X={parking_position}
	{% else %}
	PARK_TOOLHEAD
	{% endif %}
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="pause"
	
	RATOS_ECHO MSG="Print paused"

[gcode_macro RESUME]
description = Resumes the print if the printer is paused.
rename_existing = RESUME_BASE
gcode = 
	
	
	RATOS_ECHO MSG="Resuming print..."
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	
	{% set target_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set target_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if target_idex_mode != '' %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set fan_speed = printer["gcode_macro PAUSE"].fan_speed|float %}
	{% if printer["dual_carriage"] is not defined %}
	M106 S{(fan_speed * 255)}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% else %}
	{% if params.TOOLHEAD is defined %}
	
	{% if params.TOOLHEAD == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% else %}
	{% if printer["gcode_macro PAUSE"].idex_toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	{% if params.TOOLHEAD is defined %}
	_SELECT_TOOL T={params.TOOLHEAD} X=-1 Y=-1 TOOLSHIFT=false
	{% else %}
	_SELECT_TOOL T={printer["gcode_macro PAUSE"].idex_toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	{% endif %}
	
	{% set x = printer["gcode_macro PAUSE"].idex_toolhead_x|float %}
	{% set y = printer["gcode_macro PAUSE"].idex_toolhead_y|float %}
	{% set z = printer["gcode_macro PAUSE"].idex_toolhead_z|float %}
	G1 X{x} Y{y} Z{z} F{speed}
	{% if params.TOOLHEAD is defined %}
	
	SAVE_GCODE_STATE NAME=PAUSE_STATE
	{% endif %}
	{% endif %}
	
	
	{% if params.TOOLHEAD is not defined %}
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% if can_extrude %}
	G91
	G1 E{E} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1 MOVE_SPEED={speed}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	RESUME_BASE
	
	
	_LED_PRINTING
	
	RATOS_ECHO MSG="Print resumed"

[gcode_macro CANCEL_PRINT]
description = Cancels the print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	RATOS_ECHO MSG="Cancelling print..."
	END_PRINT
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	
	CANCEL_PRINT_BASE
	RATOS_ECHO MSG="Print cancelled"

[gcode_macro START_PRINT]
description = Start print procedure, use this in your Slicer.
variable_post_processor_version = 2
variable_is_printing_gcode = False
variable_both_toolheads = True
variable_object_xoffset = 0
variable_first_x = -1
variable_first_y = -1
variable_total_toolshifts = 0
variable_initial_tool = 0
variable_extruder_first_layer_temp = ""
variable_extruder_other_layer_temp = ""
gcode = 
	
	{% if params.EXTRUDER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_TEMP parameter not found.")}
	{% endif %}
	{% if params.EXTRUDER_OTHER_LAYER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_OTHER_LAYER_TEMP parameter not found.")}
	{% endif %}
	{% if params.BED_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. BED_TEMP parameter not found.")}
	{% endif %}
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' and printer["gcode_macro RatOS"].danger_force_allow_auto_center_subject|default(false)|lower != 'true'%}
	
	
	
	
	
	{ action_raise_error("The experimental auto_center_subject feature is not supported in this version of RatOS. Please disable it in the RatOS macro settings.") }
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes and printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% if printer["gcode_macro _VAOC"].is_started|default(true)|lower == 'true' %}
	_VAOC_END
	{% endif %}
	{% endif %}
	
	
	_LED_START_PRINTING
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_USER_START_PRINT { rawparams }
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_probe_stowable = printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% endif %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	{% set X0 = params.X0|default(-1)|float %}
	{% set X1 = params.X1|default(-1)|float %}
	{% set Y0 = params.Y0|default(-1)|float %}
	{% set Y1 = params.Y1|default(-1)|float %}
	{% if first_x == -1 or first_y == -1 %}
	{% set first_x = params.FIRST_X|default(-1)|float %}
	{% set first_y = params.FIRST_Y|default(-1)|float %}
	{% endif %}
	{% set total_toolshifts = params.TOTAL_TOOLSHIFTS|default(0)|int %}
	{% set initial_tool = params.INITIAL_TOOL|default(default_toolhead)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	
	
	
	
	
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(printer.heater_bed.target, true)|float %}
	
	
	{% set total_layer_count = params.TOTAL_LAYER_COUNT|default(0)|int %}
	{% set extruder_first_layer_temp = (params.EXTRUDER_TEMP|default("")).split(",") %}
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL BEACON_CONTACT_START_PRINT_TRUE_ZERO={beacon_contact_start_print_true_zero} BEACON_CONTACT_CALIBRATE_MODEL_ON_TRUE_ZERO={beacon_contact_calibrate_model_on_true_zero}
	{% endif %}
	
	_START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH BED_TEMP={bed_temp}
	
	
	RATOS_ECHO MSG="First print coordinates X:{first_x} Y:{first_y}"
	
	
	{% if params.TOTAL_LAYER_COUNT is not defined %}
	{% set link_url = "https://os.ratrig.com/docs/slicers" %}
	{% set link_text = "RatOS Slicer Configuration" %}
	{% set line_1 = '"Your slicer gcode settings are not up to date._N_Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="Incomplete Slicer Configuration detected" TYPE="warning" MSG={line_1}
	{% endif %}
	
	
	SET_PRINT_STATS_INFO CURRENT_LAYER=1
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE=1
	{% if total_layer_count > 0 %}
	SET_PRINT_STATS_INFO TOTAL_LAYER={total_layer_count}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads %}
	{% set initial_tool = 0 if initial_tool == 1 else 1 %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	{% endif %}
	
	
	{% set both_toolheads = true %}
	{% if total_toolshifts == 0 %}
	{% set both_toolheads = false %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	{% endif %}
	{% if both_toolheads and (idex_mode == "copy" or idex_mode == "mirror") %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Gcode tool changes found. Copy and mirror mode do not support toolchanges.")}
	{% endif %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set both_toolheads = true %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=initial_tool VALUE={initial_tool}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_x VALUE={first_x}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_y VALUE={first_y}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=total_toolshifts VALUE={total_toolshifts}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=both_toolheads VALUE={both_toolheads}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_first_layer_temp VALUE="'{params.EXTRUDER_TEMP}'"
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_other_layer_temp VALUE="'{params.EXTRUDER_OTHER_LAYER_TEMP}'"
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE=0
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set svv = printer.save_variables.variables %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set stepper_x_position_min = printer.fastconfig.settings.stepper_x.position_min|float %}
	{% set stepper_x_position_endstop = printer.fastconfig.settings.stepper_x.position_endstop|float %}
	{% set dual_carriage_position_max = printer.fastconfig.settings.dual_carriage.position_max|float %}
	{% set dual_carriage_position_endstop = printer.fastconfig.settings.dual_carriage.position_endstop|float %}
	{% set x_parking_space = parking_position_t0 - (stepper_x_position_endstop , stepper_x_position_min)|max %}
	{% set dc_parking_space = (dual_carriage_position_endstop , dual_carriage_position_max)|min - parking_position_t1 %}
	{% if svv.idex_xoffset|abs >= (x_parking_space - 0.5) or svv.idex_xoffset|abs >= (dc_parking_space - 0.5) %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Toolhead x-offset is too high for the available parking space. Calibrate your X and DC endstop positions and make sure you stay below 1mm." % (copy_mode_max_width)) }
	{% endif %}
	{% endif %}
	
	
	{% if (idex_mode == "copy" or idex_mode == "mirror") and printer.fastconfig.settings.ratos.enable_gcode_transform %}
	
	{% if params.MIN_X is not defined or params.MAX_X is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Something went wrong! Missing important post processor start print parameter!") }
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE=0
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	
	{% set boundary_box_min_x = params.MIN_X|default(0)|float %}
	{% set boundary_box_max_x = params.MAX_X|default(printable_x_max)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if default_toolhead == 0 %}
	
	{% set boundary_box_max_x = boundary_box_max_x + svv.idex_xoffset %}
	{% else %}
	
	{% set boundary_box_min_x = boundary_box_min_x - svv.idex_xoffset %}
	{% endif %}
	
	{% set center_x = printable_x_max / 2.0 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set object_width = boundary_box_max_x - boundary_box_min_x %}
	{% set copy_mode_max_width = center_x %}
	{% set mirror_mode_max_width = center_x - safe_distance / 2.0 %}
	
	DEBUG_ECHO PREFIX="START_PRINT" MSG="OBJECT_WIDTH: {object_width} BOUNDARY_BOX_MIN_X: {boundary_box_min_x} BOUNDARY_BOX_MAX_X: {boundary_box_max_x} CENTER_X: {center_x} SAFE_DISTANCE: {safe_distance}"
	
	
	{% if idex_mode == "copy" and object_width > copy_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for copy mode! Max supported width is %s mm" % (copy_mode_max_width)) }
	{% endif %}
	{% if idex_mode == "mirror" and object_width > mirror_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for mirror mode! Max supported width is %s mm" % (mirror_mode_max_width)) }
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = (printable_x_max - boundary_box_max_x - boundary_box_min_x) / 2 %}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE={object_xoffset}
	{% endif %}
	
	{% endif %}
	
	
	{% set has_initial_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_toolhead_filament_sensor %}
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% set has_initial_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_bowden_filament_sensor %}
	
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% if printer["dual_carriage"] is defined and both_toolheads %}
	
	{% set has_secondary_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set has_secondary_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_CHAMBER_FILTER_ON AT="before_print_start"
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true' %}
	{% if both_toolheads %}
	RATOS_ECHO MSG="Spool join is not possible if both toolheads are in use!"
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	{% endif %}
	
	
	CLEAR_PAUSE
	{% if printer["gcode_macro RatOS"].force_absolute_position|lower == 'true' %}
	G90
	{% endif %}
	SAVE_GCODE_STATE NAME=start_print_state
	
	
	G21
	
	G90
	
	M82
	_USER_START_PRINT_BEFORE_HOMING { rawparams }
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_BEGIN_BATCH
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_Z_HOP
	
	
	{% if idex_mode != '' and not (printer.fastconfig.settings.beacon is defined and (beacon_contact_start_print_true_zero or beacon_adaptive_heat_soak)) %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	{% if chamber_temp > 0 %}
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED={printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float}
	{% endif %}
	{% endif %}
	_CHAMBER_HEATER_ON START_CHAMBER_TEMP={start_chamber_temp} CHAMBER_TEMP={chamber_temp}
	_USER_START_PRINT_HEAT_CHAMBER { rawparams } CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_START_PRINT_BEFORE_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	RATOS_ECHO MSG="Heating bed..."
	
	M190 S{bed_temp}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_adaptive_heat_soak %}
	_MOVE_TO_SAFE_Z_HOME
	
	G1 Z2.5 F{z_speed}
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK LAYER_QUALITY={beacon_adaptive_heat_soak_layer_quality} MAXIMUM_FIRST_LAYER_DURATION={beacon_adaptive_heat_soak_maximum_first_layer_duration} MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={beacon_adaptive_heat_soak_max_wait}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_BED { rawparams }
	
	
	_START_PRINT_AFTER_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	_USER_START_PRINT_BED_MESH { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_BED_MESH X0={X0} X1={X1} Y0={Y0} Y1={Y1} T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_END_BATCH
	{% endif %}
	
	
	{% if idex_mode == '' %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[initial_tool]|float}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[0]|float}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={extruder_first_layer_temp[1]|float}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_PARK { rawparams }
	
	
	_START_PRINT_PARK
	
	
	RATOS_ECHO MSG="Heating Extruder..."
	{% if idex_mode == '' %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[initial_tool]|float}  MAXIMUM={extruder_first_layer_temp[initial_tool]|float + 5}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[0]|float}  MAXIMUM={extruder_first_layer_temp[0]|float + 5}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder1" MINIMUM={extruder_first_layer_temp[1]|float}  MAXIMUM={extruder_first_layer_temp[1]|float + 5}
	{% endif %}
	{% endif %}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	{% if idex_mode == '' %}
	_LED_PRINTING
	{% else %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	_LED_PRINTING
	{% else %}
	{% if both_toolheads %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	{% if toolchange_standby_temp > -1 %}
	_LED_TOOLHEAD_STANDBY TOOLHEAD={0 if initial_tool == 1 else 1}
	{% else %}
	_LED_PRINTING TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% else %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_EXTRUDER { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_AFTER_HEATING_EXTRUDER X0={X0} X1={X1} Y0={Y0} Y1={Y1} INITIAL_TOOLHEAD={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if idex_mode != '' %}
	{% if not both_toolheads %}
	{% if initial_tool != default_toolhead %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if idex_mode != '' %}
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=standby VALUE=False
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=standby VALUE=False
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if initial_tool == 1 else 'extruder1'} TARGET={toolchange_standby_temp}
	SET_GCODE_VARIABLE MACRO=T{0 if initial_tool == 1 else 1} VARIABLE=standby VALUE=True
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=start_print_state
	
	{% if printer["dual_carriage"] is defined %}
	_SET_IDEX_MODE_OFFSET
	{% endif %}
	
	
	{% if idex_mode != '' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% if idex_mode == "copy" and idex_mode != act_idex_mode %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == "mirror" and idex_mode != act_idex_mode %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={object_xoffset} MOVE=0
	{% endif %}
	{% else %}
	_SELECT_TOOL T={initial_tool} TOOLSHIFT=false
	_SET_TOOLHEAD_OFFSET
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	_SET_EXTRUSION_MODE
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={printer["print_stats"].print_duration}
	{% endif %}
	
	
	_USER_END_START_PRINT { rawparams }
	
	G92 E0
	
	
	_CHAMBER_FILTER_ON AT="after_print_start"
	
	_ALERT_NON_ZERO_Z_OFFSET
	
	RATOS_ECHO MSG="Printing..."

[gcode_macro _START_PRINT_BEFORE_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set is_stowable_probe = true if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' else false %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Pre-heating extruder..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={min_temp}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET={min_temp}
	{% endif %}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	{% endif %}
	{% endif %}
	
	
	{% if not is_stowable_probe %}
	{% if printer["dual_carriage"] is defined and act_t != default_toolhead %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	{% endif %}
	RATOS_ECHO MSG="Heat soaking z probe..."
	_MOVE_TO_SAFE_Z_HOME
	
	G0 Z2 F{z_speed}
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Waiting for extruder to be preheated..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	{% if default_toolhead == 0 %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_Z_HOP
	{% endif %}
	
	
	{% if auto_z_offset_calibration %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	PARK_TOOLHEAD
	_CLEANING_MOVE TOOLHEAD={default_toolhead} AUTOMATED=True
	_SELECT_TOOL T={0 if default_toolhead == 1 else 1} X={parking_position_t0 if default_toolhead == 1 else parking_position_t1} Y=0 TOOLSHIFT=false
	_CLEANING_MOVE TOOLHEAD={0 if default_toolhead == 1 else 1} AUTOMATED=True
	_VAOC_CALIBRATE_Z_OFFSET AUTO_Z_OFFSET=True
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=false
	{% endif %}
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	{% if needs_rehoming %}
	G28 Z
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	_START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE
	{% endif %}
	{% endif %}
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	PROBE PROBE_METHOD=contact SAMPLES=1

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	{% set fuzzy_radius = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_radius|default(0)|float if beacon_contact_start_print_true_zero_fuzzy_position else 0 %}
	
	{% set contact_true_zero_temp_has_been_set = False %}
	
	
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	
	
	
	{% if printer.beacon.last_probe_result|lower == "ok" %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	RATOS_ECHO MSG="Auto calibration nozzle wipe with probe result {last_z_offset}..."
	G0 Z{(0.2 + last_z_offset)} F{z_speed}
	G0 X70 F300
	{% else %}
	RATOS_ECHO MSG="Skipping auto calibration nozzle wipe because probing failed!"
	{% endif %}
	{% elif beacon_contact_wipe_before_true_zero_method == "probe_clean" %}
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	
	{% set contact_true_zero_temp_has_been_set = True %}
	
	
	
	
	
	
	
	
	BEACON_PROBE_CLEAN X=50 Y=10
	{% else %}
	CONSOLE_ECHO TYPE="error" TITLE="Unknown wipe method" MSG="Unknown wipe method '{beacon_contact_wipe_before_true_zero_method}' configured, skipping wipe before beacon true zero."
	{% endif %}
	{% endif %}
	
	
	G0 Z5 F{z_speed}
	_MOVE_TO_SAFE_Z_HOME FUZZY_RADIUS={fuzzy_radius}
	
	
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION
	
	{% if not contact_true_zero_temp_has_been_set %}
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon contact auto calibration..."
	
	{% if beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	
	G0 Z5 F{z_speed}

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION]
gcode = 
	{% set pos = printer.ratos.last_move_to_safe_z_home_position %}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE={pos[0]}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE={pos[1]}

[gcode_macro _START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set first_x = printer["gcode_macro START_PRINT"].first_x|default(-1)|float %}
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2.0 %}
	{% set center_y = printable_y_max / 2.0 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% if printer["dual_carriage"] is defined %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% endif %}
	
	
	{% set X0 = params.X0|default(-1)|int %}
	{% set X1 = params.X1|default(-1)|int %}
	{% set Y0 = params.Y0|default(-1)|int %}
	{% set Y1 = params.Y1|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	
	{% if idex_mode == '' %}
	
	_PRIME
	{% else %}
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	RATOS_ECHO PREFIX="IDEX" MSG="using combined prime offset for IDEX {idex_mode} mode"
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	{% if both_toolheads %}
	{% if initial_toolhead == 0 %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T{initial_toolhead}"
	_SELECT_TOOL T={initial_toolhead} TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	SET_MACRO_TRAVEL_SETTINGS
	
	{% if (X0 > -1 and Y1 > -1) or (first_x > 0 and first_y > 0) %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	{% endif %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	{% set first_z = 1 %}
	{% else %}
	{% set first_z = 3 %}
	{% endif %}
	
	
	{% if idex_mode == "mirror" %}
	{% if first_y >= 0 %}
	G0 Y{first_y} F{speed}
	{% else %}
	G0 Y{Y1} F{speed}
	{% endif %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={initial_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={initial_toolhead} E={printer["gcode_macro RatOS"].toolchange_first_purge|default(50)|float}
	_CLEANING_MOVE TOOLHEAD={initial_toolhead} AUTOMATED=True
	{% endif %}
	{% if first_x >= 0 and first_y >= 0 %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% else %}
	{% set first_x = X0 %}
	{% set first_y = Y0 %}
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'min' %}
	{% set first_x = X0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'max' %}
	{% set first_x = X1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|float <= center_x %}
	{% set first_x = X0 %}
	{% else %}
	{% set first_x = X1 %}
	{% endif %}
	{% endif %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'min' %}
	{% set first_y = Y0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'max' %}
	{% set first_y = Y1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|float <= center_y %}
	{% set first_y = Y0 %}
	{% else %}
	{% set first_y = Y1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	
	
	_LOAD_RATOS_SKEW_PROFILE

[gcode_macro _PRIME]
gcode = 
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	PRIME_BLOB INITIAL_TOOLHEAD={params.INITIAL_TOOLHEAD} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={params.IDEX_MODE} Y1={params.Y1}
	{% else %}
	
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif params.IDEX_MODE == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro END_PRINT]
description = End print procedure, use this in your Slicer.
gcode = 
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SAVE_GCODE_STATE NAME=end_print_state
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = printer["gcode_macro START_PRINT"].object_xoffset|default(0)|float %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(0-object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={(0-object_xoffset)}
	{% endif %}
	{% endif %}
	
	
	_USER_END_PRINT_BEFORE_HEATERS_OFF { rawparams }
	_END_PRINT_BEFORE_HEATERS_OFF
	TURN_OFF_HEATERS
	_USER_END_PRINT_AFTER_HEATERS_OFF { rawparams }
	_END_PRINT_AFTER_HEATERS_OFF
	_USER_END_PRINT_PARK { rawparams }
	_END_PRINT_PARK
	
	
	{% if printer["gcode_macro RatOS"].skew_profile is defined %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined and printer["gcode_macro RatOS"].end_print_motors_off|lower != 'false' %}
	
	M84
	{% endif %}
	
	
	M107
	
	
	BED_MESH_CLEAR
	RATOS_ECHO MSG="Done :)"
	
	
	RESTORE_GCODE_STATE NAME=end_print_state
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	M84
	{% endif %}
	
	
	RESET_NAMED_OFFSET EVENT="end_print"
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_CHAMBER_FILTER_ON AT="print_end"
	_CHAMBER_FILTER_OFF
	
	
	_CHAMBER_HEATER_OFF
	
	_USER_END_PRINT_FINISHED { rawparams }

[gcode_macro _END_PRINT_BEFORE_HEATERS_OFF]
gcode = 
	RATOS_ECHO MSG="Cleaning up..."

[gcode_macro _END_PRINT_AFTER_HEATERS_OFF]
gcode = 
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% set z_hop = printer["gcode_macro RatOS"].end_print_park_z_hop|float %}
	{% set r = printer["gcode_macro RatOS"].end_print_retract_filament|default(4)|float %}
	{% if current_z < (max_z - z_hop) %}
	{% set z_safe = z_hop %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G91
	
	{% if can_extrude %}
	G1 E-2 F3600
	{% endif %}
	
	G0 Z{z_safe} F3600
	
	{% if can_extrude %}
	G1 E-{(r-2)} F3600
	{% endif %}
	
	G90

[gcode_macro _SET_EXTRUSION_MODE]
gcode = 
	
	{% if printer["gcode_macro RatOS"].relative_extrusion|lower == 'true' %}
	M83
	{% else %}
	M82
	{% endif %}

[gcode_macro GENERATE_SHAPER_GRAPHS]
description = Genarates input shaper resonances graphs for analysis. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	{% set hz_per_sec = params.HZ_PER_SEC|default(1)|float %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set copy_mode_offset = printable_x_max / 4.0 %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	_IDEX_SINGLE
	{% endif %}
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	
	
	{% if idex_mode != 'copy' and idex_mode != 'mirror' %}
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	{% endif %}
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Shaper graph"

[gcode_shell_command generate_shaper_graph_x]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-x.sh
timeout = 60.
verbose = True

[gcode_shell_command generate_shaper_graph_y]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-y.sh
timeout = 60.
verbose = True

[gcode_macro MEASURE_COREXY_BELT_TENSION]
description = Generates resonance graph used to ensure belts are equally tensioned. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	_IDEX_SINGLE
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if measure_t1 == false or measure_t0 == false %}
	{action_raise_error("Axis specified. Not supported for belt tension on Y.")}
	{% else %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	G4 P5000
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	PARK_TOOLHEAD
	{% endif %}
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	G1 X{parking_position_t1} F{speed}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	
	
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Belt Tension Graph"

[gcode_shell_command generate_belt_tension_graph]
command = /home/pi/printer_data/config/RatOS/scripts/generate-belt-tension-graph.sh
timeout = 90.
verbose = True

[idle_timeout]
gcode = 
	{% if printer.webhooks.state|lower == 'ready' %}
	{% if printer.pause_resume.is_paused|lower == 'false' %}
	_USER_BEFORE_IDLE_TIMEOUT
	RATOS_ECHO PREFIX="IDLE" MSG="2 hours since last activity. Powering off heaters and motors.."
	TURN_OFF_HEATERS
	M84
	_USER_AFTER_IDLE_TIMEOUT
	{% endif %}
	{% endif %}
timeout = 7200

[temperature_sensor raspberry_pi]
sensor_type = temperature_host

[skew_correction]

[named_offsets]

[input_shaper]

[virtual_sdcard]
path = ~/printer_data/gcodes

[display_status]

[pause_resume]

[force_move]
enable_force_move = True

[respond]

[resonance_generator]

[ratos]
allow_unknown_gcode_generator = True
enable_gcode_transform = True

[exclude_object]

[bed_mesh]
split_delta_z = 0.001
horizontal_move_z = 2
mesh_min = 20,20
mesh_max = 480,480
probe_count = 40,40
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = .2
speed = 600
log_points = False

[fastconfig]

[heater_bed]
heater_pin = heater_bed_heating_pin
sensor_pin = heater_bed_sensor_pin
sensor_type = Generic 3950
min_temp = 0
max_temp = 140
pwm_cycle_time = 0.103
control = pid
pid_kp = 61.987
pid_ki = 1.781
pid_kd = 539.289

[printer]
kinematics = ratos_hybrid_corexy
max_velocity = 800
max_accel = 10000
minimum_cruise_ratio = 0.5
max_z_velocity = 50
max_z_accel = 600
square_corner_velocity = 5

[ratos_hybrid_corexy]
inverted = true

[dual_carriage]
axis = x
safe_distance = 55
position_max = 559.6
position_endstop = 559.6
position_min = 0
step_pin = PF9
dir_pin = dual_carriage_dir_pin
enable_pin = !PG2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t1:PA2

[gcode_macro _SET_IDEX_MODE_OFFSET]
description = "Internal use only. Sets the 'idex_mode' named offset that the active idex mode requires."
gcode = 
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_SET_IDEX_MODE_OFFSET" MSG="idex_mode: {idex_mode}, center_x: {center_x}"
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	SET_NAMED_OFFSET NAME=idex_mode X={(-center_x / 2)}
	{% else %}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% else %}
	{action_raise_error("_SET_IDEX_MODE_OFFSET: Printer not homed")}
	{% endif %}

[gcode_macro IDEX_SINGLE]
gcode = 
	_IDEX_REMAP_TOOLHEADS ENABLE=False
	_IDEX_SINGLE

[gcode_macro _IDEX_SINGLE]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_single"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set init = params.INIT|default(0)|int %}
	{% set new_x = params.X|default(-1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_default_t = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="init: {init}, new_x: {new_x}, idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, act_t: {act_t}"
	
	{% if idex_mode == "copy" or idex_mode == "mirror" or init == 1 %}
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="reset idex_mode offset"
	G1 X{center_x} F{(speed)}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="activate default carriage"
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolheads"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	G90
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position."
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1}
	G1 X{parking_position_default_t} F{speed}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move default toolhead to its new position."
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% if new_x == -1 %}
	{% set new_x = center_x %}
	{% endif %}
	G1 X{new_x} F{speed}
	
	M400
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="X Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set extruder motion queue."
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if default_toolhead==0 else default_toolhead}
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolhead offset."
	_SET_TOOLHEAD_OFFSET
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set input shaper."
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[default_toolhead]|float)} SHAPER_FREQ_Y={(shaper_y_freq[default_toolhead]|float)} SHAPER_TYPE_X={(shaper_x_type[default_toolhead]|lower)} SHAPER_TYPE_Y={(shaper_y_type[default_toolhead]|lower)}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="update Frontend."
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if default_toolhead==0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if default_toolhead==1 else False}
	{% else %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_single"

[gcode_macro IDEX_COPY]
gcode = 
	_IDEX_COPY

[gcode_macro _IDEX_COPY]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_copy"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set y = params.Y|default(-1)|int %}
	{% set dance = params.DANCE|default(1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_COPY" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}, y: {y}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "copy" %}
	{% if idex_mode == "mirror" %}
	{% if y>=0 %}
	G1 X{center_x} Y{y} F{(speed)}
	{% else %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	
	
	{% if idex_mode != "mirror" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance == 1 %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[2]|float)} SHAPER_FREQ_Y={(shaper_y_freq[2]|float)} SHAPER_TYPE_X={(shaper_x_type[2]|lower)} SHAPER_TYPE_Y={(shaper_y_type[2]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_copy"

[gcode_macro IDEX_MIRROR]
gcode = 
	_IDEX_MIRROR

[gcode_macro _IDEX_MIRROR]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_mirror"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set dance = params.DANCE|default(1)|int %}
	{% set priming = params.PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_MIRROR" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "mirror" %}
	
	{% if idex_mode == "copy" %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS MIRROR_PRIMING={params.PRIMING}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=MIRROR
	
	
	{% if idex_mode != "copy" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance and not priming %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[3]|float)} SHAPER_FREQ_Y={(shaper_y_freq[3]|float)} SHAPER_TYPE_X={(shaper_x_type[3]|lower)} SHAPER_TYPE_Y={(shaper_y_type[3]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_mirror"

[gcode_macro _IDEX_SET_TOOLHEADS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set mirror_priming = params.MIRROR_PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position_inactive_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_IDEX_SET_TOOLHEADS" MSG="idex_mode: {idex_mode}, act_t: {act_t}, center_x: {center_x}, mirror_priming: {mirror_priming}"
	
	
	{% if act_t != default_toolhead %}
	_SET_TOOLHEAD_OFFSET FORCE_TOOLHEAD={default_toolhead} MOVE=1
	{% endif %}
	
	{% if mirror_priming %}
	
	
	
	{% if parking_position_t0|abs < parking_position_t1 - printable_x_max %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{printable_x_max + parking_position_t0|abs} F{(speed)}
	{% else %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{0 - (parking_position_t1 - printable_x_max)} F{(speed)}
	{% endif %}
	
	{% else %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1} MODE=PRIMARY
	G1 X{parking_position_inactive_t} F{(speed)}
	
	
	{% if act_t==1 %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{center_x / 2} F{(speed)}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"

[gcode_macro IDEX_PARK]
gcode = 
	
	PARK_TOOLHEAD

[gcode_macro PARK_TOOLHEAD]
gcode = 
	
	{% set idex_mode = 'none' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="PARK_TOOLHEAD" MSG="Parking T{act_t}.."
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set parking_position_inact_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set printable_y_min = printer["gcode_macro RatOS"].printable_y_min|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" and 'xy' in printer.toolhead.homed_axes %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% elif printer.toolhead.position.y|float < printable_y_min %}
	G1 Y{printable_y_min} F{speed}
	{% endif %}
	
	SAVE_GCODE_STATE NAME=_PARK_TOOLHEAD
	G90
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0.5
	
	
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_inact_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	
	SET_VELOCITY_LIMIT ACCEL={printer.toolhead.max_accel} MINIMUM_CRUISE_RATIO=0.5
	M400
	RESTORE_GCODE_STATE NAME=_PARK_TOOLHEAD
	
	{% endif %}

[gcode_macro JOIN_SPOOLS]
gcode = 
	
	{% set spools = params.SPOOLS|default("") %}
	
	{% if spools == "" %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% else %}
	{% if spools != "0,1" and spools != "1,0" %}
	RATOS_ECHO MSG="Wrong spool configuration!"
	RATOS_ECHO MSG="Join Spools = JOIN_SPOOLS SPOOLS=0,1"
	RATOS_ECHO MSG="Deactivate = JOIN_SPOOLS SPOOLS="
	{% else %}
	{% if spools == "0,1" or spools == "1,0" %}
	_IDEX_JOIN_SPOOLS ENABLE=true
	{% else %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_JOIN_SPOOLS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if enable %}
	{% set has_t0_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t1_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t0_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined else false %}
	{% set has_t1_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined else false %}
	{% if (has_t0_toolhead_filament_sensor and has_t1_toolhead_filament_sensor) or (has_t0_bowden_filament_sensor and has_t1_bowden_filament_sensor) %}
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=True
	RATOS_ECHO MSG="Spool joining enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Can not enable spool joining! No filament sensors found."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining deactivated!"
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining is not possible in copy and mirror mode!"
	{% endif %}

[gcode_macro _JOIN_SPOOL]
gcode = 
	
	{% set old_toolhead = params.TOOLHEAD|int %}
	{% set new_toolhead = 0 if old_toolhead == 1 else 1 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set purge_after_load = printer["gcode_macro T%s" % new_toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_JOIN_SPOOL" MSG="toolhead: {new_toolhead}"
	
	{% set has_filament = true %}
	{% set has_new_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% set has_new_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% if has_new_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	{% if has_new_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	
	{% if has_filament %}
	RATOS_ECHO MSG="Joining spools! Please wait for extruder to heat up...."
	
	
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={new_toolhead}
	
	
	_DEACTIVATE_TOOLHEAD TOOLHEAD={old_toolhead}
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set extruder_temp = extruder_first_layer_temp[new_toolhead]|float %}
	{% else %}
	{% set extruder_temp = extruder_other_layer_temp[new_toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if new_toolhead == 0 else 'extruder1'} TARGET={extruder_temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if new_toolhead == 0 else 'extruder1'} MINIMUM={extruder_temp}  MAXIMUM={extruder_temp + 5}
	
	
	{% if purge_after_load > 0 %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_toolhead == 0 else new_toolhead}
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={new_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={new_toolhead} E={purge_after_load}
	_CLEANING_MOVE TOOLHEAD={new_toolhead} AUTOMATED=True
	
	
	SET_DUAL_CARRIAGE CARRIAGE={old_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if old_toolhead == 0 else old_toolhead}
	
	{% endif %}
	
	
	RESUME TOOLHEAD={new_toolhead}
	
	
	_IDEX_JOIN_SPOOLS ENABLE=false
	
	{% else %}
	{ action_raise_error("Spool join failed! No filament found or filament sensor is disabled.") }
	{% endif %}

[gcode_macro REMAP_TOOLHEADS]
gcode = 
	
	{% set toolheads = params.TOOLHEADS|default("") %}
	
	{% if toolheads == "" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% else %}
	{% if toolheads != "0,1" and toolheads != "1,0" %}
	RATOS_ECHO MSG="Wrong toolhead configuration!"
	RATOS_ECHO MSG="Remap = REMAP_TOOLHEADS TOOLHEADS=0,1"
	RATOS_ECHO MSG="Deactivate = REMAP_TOOLHEADS TOOLHEADS="
	{% else %}
	{% if toolheads == "0,1" or toolheads == "1,0" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=true
	_IDEX_SINGLE
	{% else %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_REMAP_TOOLHEADS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	{% if not enable or (idex_mode != "copy" and idex_mode != "mirror") %}
	{% if enable %}
	RATOS_ECHO MSG="Toolhead remapping enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping deactivated!"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE={enable}
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping not possible in copy and mirror mode!"
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	{% endif %}

[gcode_macro SHAPER_CALIBRATE]
rename_existing = SHAPER_CALIBRATE_ORG
gcode = 
	RATOS_ECHO PREFIX="IDEX" MSG="SHAPER_CALIBRATE is useless on IDEX machines. Please use the GENERATE_SHAPER_GRAPHS macro and type the values into `variable_shaper_*_freq` and `variable_shaper_*_type manually`."

[gcode_shell_command generate_shaper_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-shaper-graph.sh
timeout = 120.
verbose = True

[gcode_shell_command generate_tension_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-belt-tension-graph.sh
timeout = 120.
verbose = True

[gcode_macro SET_PRESSURE_ADVANCE]
variable_snyc_toolheads = False
rename_existing = SET_PRESSURE_ADVANCE_BASE
gcode = 
	{% if params.SYNC_TOOLHEADS is defined %}
	{% set snyc_toolheads = true if params.SYNC_TOOLHEADS|default(false)|lower == 'true' else false %}
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=True
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="Syncing toolheads..."
	{% else %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' or snyc_toolheads %}
	{% set advance = params.ADVANCE|default(printer['extruder'].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['extruder'].smooth_time|float)|float %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T0"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T1"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder1' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% else %}
	{% set extruder = 'extruder' if act_t == 0 else 'extruder1' %}
	{% if params.EXTRUDER is defined %}
	{% set extruder = params.EXTRUDER %}
	{% endif %}
	{% if extruder == 'extruder' or extruder == 'extruder1' %}
	{% set advance = params.ADVANCE|default(printer['%s' % extruder].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['%s' % extruder].smooth_time|float)|float %}
	SET_PRESSURE_ADVANCE_BASE EXTRUDER={extruder} ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% if params.EXTRUDER is not defined %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG={"T%s" % act_t}
	{% endif %}
	{% else %}
	SET_PRESSURE_ADVANCE_BASE { rawparams }
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro M106]
rename_existing = M106.1
variable_swap_speed = -1
gcode = 
	
	{% set s = [[params.S|default(255)|int, 255]|min, 0]|max %}
	{% set p = params.P|default(-1)|int %}
	{% set speed = s / 255 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set t = 1 if idex_mode=='primary' else 0 %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(0)|int == 1 else false %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set sync_fans = true %}
	{% endif %}
	
	
	{% if sync_fans and idex_mode != "copy" and idex_mode != "mirror" %}
	
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int %}
	
	
	{% if toolshift_count > total_toolshifts %}
	{% set sync_fans = false %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE=-1
	
	
	{% if p == -1 %}
	
	{% if speed == 0 %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed}
	{% else %}
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE={speed}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={(speed if (t == 0 or sync_fans) else 0)}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={(speed if (t == 1 or sync_fans) else 0)}
	{% endif %}
	{% else %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed if t == p else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed if t == p else 0}
	{% endif %}
	
	
	M106.1 S{s}

[gcode_macro M107]
rename_existing = M107.1
gcode = 
	{% set p = params.P|default(-1)|int %}
	M106 S0 P{p}

[gcode_macro _SELECT_TOOL]
variable_last_timestamp = 0
gcode = 
	{% if params.T is defined %}
	{% set idex_mode = '' %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if "xyz" not in printer.toolhead.homed_axes and (idex_mode == "copy" or idex_mode == "mirror") %}
	_IDEX_SINGLE
	{% set idex_mode = 'reset' %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set new_t = params.T|int %}
	
	
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads and is_printing_gcode %}
	{% set new_t = 0 if new_t == 1 else 1 %}
	{% endif %}
	
	
	{% set toolchange_prepurging_timer = printer["gcode_macro RatOS"].toolchange_prepurging_timer|default(0)|int %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	DEBUG_ECHO PREFIX="_SELECT_TOOL" MSG="act_t: {act_t}, new_t: {new_t}, is_printing_gcode: {is_printing_gcode}, swap_toolheads: {swap_toolheads}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	{% set act_extruder = 'extruder%s' % ('' if new_t == 0 else new_t) %}
	{% if new_t != act_t or printer.toolhead.extruder != act_extruder or idex_mode == 'reset' %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Selecting T{new_t}.."
	
	
	M220 S100
	
	
	
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(1)|int == 1 else false %}
	
	
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set toolshift = false %}
	{% endif %}
	
	
	{% set fan_speed = printer["fan_generic part_fan_t%s" % act_t].speed %}
	
	
	{% set deactivate_toolhead = false %}
	{% if is_printing_gcode %}
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int + 1 %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE={toolshift_count}
	{% if toolshift_count == total_toolshifts %}
	{% set deactivate_toolhead = true %}
	{% endif %}
	{% endif %}
	
	
	{% set needs_wakeup = true if printer["gcode_macro T%s" % new_t].standby|default(false)|lower == 'true' else false %}
	
	
	{% set needs_purging = false %}
	{% set wake_up_purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% if is_printing_gcode and toolchange_prepurging_timer > 0 and wake_up_purge > 0 %}
	{% set new_timestamp = printer["print_stats"].print_duration %}
	{% set elapsed_time = new_timestamp - last_timestamp %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={new_timestamp}
	{% if elapsed_time > toolchange_prepurging_timer %}
	{% set needs_purging = true %}
	{% endif %}
	{% endif %}
	
	
	{% set first_use_purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% if toolshift_count == 1 and first_use_purge > 0 %}
	{% set needs_purging = true %}
	{% endif %}
	
	
	{% if is_printing_gcode and (toolchange_standby_temp > -1 or needs_purging or needs_wakeup) %}
	_TOOLHEAD_STANDBY TOOLHEAD={act_t}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	_TOOLHEAD_WAKEUP TOOLHEAD={new_t} X={new_x} Y={new_y} Z={new_z} FAN_SPEED={fan_speed} TOOLSHIFT_COUNT={toolshift_count}
	{% else %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(false)|lower == 'true' else false %}
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if (new_t == 0 or sync_fans) else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if (new_t == 1 or sync_fans) else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	_TOOLCHANGE T={new_t} X={new_x} Y={new_y} Z={new_z} PARK_T0={park_t0} PARK_T1={park_t1} TOOLSHIFT={toolshift}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[new_t]|float)} SHAPER_FREQ_Y={(shaper_y_freq[new_t]|float)} SHAPER_TYPE_X={(shaper_x_type[new_t]|lower)} SHAPER_TYPE_Y={(shaper_y_type[new_t]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if new_t == 0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if new_t == 1 else False}
	
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% set sanity_check_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if new_t == 0 %}
	{% if printer.toolhead.extruder == 'extruder' %}
	{% if sanity_check_idex_mode == 'primary' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% elif new_t == 1 %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% if sanity_check_idex_mode == 'inactive' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _TOOLHEAD_STANDBY]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Putting toolhead T{toolhead} into standby mode."
	DEBUG_ECHO PREFIX="_TOOLHEAD_STANDBY" MSG="toolhead: {toolhead}, config_z_hop: {config_z_hop}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={toolhead} SYNC=0
	PARK_TOOLHEAD
	
	
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={toolchange_standby_temp}
	{% endif %}
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=True
	{% endif %}
	
	
	_LED_TOOLHEAD_STANDBY TOOLHEAD={toolhead}

[gcode_macro _TOOLHEAD_WAKEUP]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set fan_speed = params.FAN_SPEED|float %}
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift_count = params.TOOLSHIFT_COUNT|default(0)|int %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% if toolshift_count == 1 %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% endif %}
	{% set needs_wakeup = true if printer["gcode_macro T%s" % toolhead].standby|default(false)|lower == 'true' else false %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Waking up toolhead T{toolhead}. Please wait for extruder to heat up..."
	DEBUG_ECHO PREFIX="_TOOLHEAD_WAKEUP" MSG="toolhead: {toolhead}, fan_speed: {fan_speed}, new_x: {new_x}, new_y: {new_y}, new_z: {new_z}, config_z_hop: {config_z_hop}"
	
	
	_LED_TOOLHEAD_WAKEUP TOOLHEAD={toolhead}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={toolhead} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE=1
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if toolhead == 0 else toolhead}
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if needs_wakeup %}
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set temp = extruder_first_layer_temp[toolhead]|float %}
	{% else %}
	{% set temp = extruder_other_layer_temp[toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if toolhead == 0 else 'extruder1'} MINIMUM={temp}  MAXIMUM={temp + 5}
	{% endif %}
	
	
	_LED_PRINTING TOOLHEAD={toolhead}
	
	
	{% if purge > 0 %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={toolhead} E={purge}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	
	
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if toolhead == 1 else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	G92 E0
	G1 E-{e} F{feedrate}
	G92 E0
	
	
	{% if new_x >= 0 and new_y >= 0 %}
	G1 X{new_x} Y{new_y} F{speed}
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={config_z_hop} T={toolhead} SYNC=0
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=False

[gcode_macro _TOOLCHANGE]
variable_toolshift_count = 0
gcode = 
	
	
	{% set new_t = params.T|default(-1)|int %}
	{% set new_x = params.X|default(-1.0)|float %}
	{% set new_y = params.Y|default(-1.0)|float %}
	{% set new_z = params.Z|default(-1.0)|float %}
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(true)|lower == 'true' else false %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T: {new_t}, X: {new_x}, Y: {new_y}, Z: {new_z}, PARK_T0: {park_t0}, PARK_T1: {park_t1}, IS_PRINTING_GCODE: {is_printing_gcode}, TOOLSHIFT: {toolshift}"
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	{% if park_t0 >= 0 and park_t1 >= 0 %}
	{% set parking_position_t0 = park_t0 %}
	{% set parking_position_t1 = park_t1 %}
	{% set parking_position_act_t = park_t0 if act_t == 0 else park_t1 %}
	{% endif %}
	
	
	{% if not is_printing_gcode and not toolshift %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Changing tool to T{new_t} without retracting/extruding or moving the toolheads except for parking."
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	G90
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% if not is_printing_gcode and toolshift and new_x < 0 and new_y < 0 %}
	{% set new_x = center_x %}
	{% set new_y = printer.gcode_move.gcode_position.y|float %}
	{% endif %}
	
	{% if new_x < 0 or new_y < 0 %}
	
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="No new X or Y position given, parking the active toolhead and activating the new toolhead without moving it."
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={new_t}
	
	
	{% if "x" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	{% if is_printing_gcode %}
	_EXTRUDE T={new_t}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	{% if "xyz" not in printer.toolhead.homed_axes %}
	
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	
	
	{% set svv = printer.save_variables.variables %}
	{% if new_t == default_toolhead %}
	{% set new_xoffset = 0 %}
	{% set new_yoffset = 0 %}
	{% set new_zoffset = 0 %}
	{% else %}
	{% set new_xoffset = -svv.idex_xoffset %}
	{% set new_yoffset = -svv.idex_yoffset %}
	{% set new_zoffset = -svv.idex_zoffset %}
	{% endif %}
	
	{% set xoffset_correction = new_xoffset - printer.named_offsets.toolhead_alignment.x %}
	{% set yoffset_correction = new_yoffset - printer.named_offsets.toolhead_alignment.y %}
	{% set zoffset_correction = new_zoffset - printer.named_offsets.toolhead_alignment.z %}
	
	{% if new_t == 0 %}
	
	{% set t0_act_x = parking_position_t0 %}
	{% set t1_act_x = printer.toolhead.position.x|float %}
	{% set t0_new_x = new_x %}
	{% set t1_new_x = parking_position_t1 %}
	{% set t0_distance = t0_new_x - t0_act_x %}
	{% set t1_distance = t1_new_x - t1_act_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T0."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	
	
	G1 X{t0_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x + (t1_new_x - t1_act_x)} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t0_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T0: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% elif new_t == 1 %}
	
	{% set t0_act_x = printer.toolhead.position.x|float %}
	{% set t1_act_x = parking_position_t1 %}
	{% set t0_new_x = parking_position_t0 %}
	{% set t1_new_x = new_x %}
	{% set t0_distance = t0_act_x - t0_new_x %}
	{% set t1_distance = t1_act_x - t1_new_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T1."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x - t1_distance + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t1_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T1: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% endif %}
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	{% endif %}

[gcode_macro _ZHOP_BEFORE_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_hop = params.Z_HOP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_HOP: {z_hop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="COMBINED_ZHOP G1 Z+{z_hop} E-{e} F{speed * 60}"
	G1 Z+{z_hop} E-{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="ZHOP G1 Z+{z_hop} F{speed * 60}"
	G1 Z+{z_hop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="RETRACT G1 E-{e} F{feedrate}"
	G1 E-{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _ZDROP_AFTER_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_drop = params.Z_DROP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_DROP: {z_drop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="COMBINED_ZDROP G1 Z-{z_drop} E{e} F{speed * 60}"
	G1 Z-{z_drop} E{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="ZDROP G1 Z-{z_drop} F{speed * 60}"
	G1 Z-{z_drop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="EXTRUDE G1 E{e} F{feedrate}"
	G1 E{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _EXTRUDE]
gcode = 
	
	{% set t = params.T|int %}
	
	
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	
	DEBUG_ECHO PREFIX="_EXTRUDE" MSG="G1 E{e} F{feedrate * 60}"
	
	
	G91
	M82
	G92 E0
	G1 E{e} F{feedrate * 60}
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _DEACTIVATE_TOOLHEAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_DEACTIVATE_TOOLHEAD" MSG="TOOLHEAD {toolhead}"
	
	
	{% if toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% endif %}
	
	
	M106.1 S0
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={toolhead}

[delayed_gcode _INIT_TOOLHEADS]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	_IDEX_SINGLE INIT=1
	
	
	{% if printer.fastconfig.settings.dual_carriage.safe_distance is defined %}
	{% if printer.fastconfig.settings.dual_carriage.safe_distance|float < 50 %}
	{ action_emergency_stop("Dual carriage safe_distance seems to be too low!") }
	{% endif %}
	{% else %}
	{ action_emergency_stop("Dual carriage safe_distance not defined!") }
	{% endif %}

[gcode_macro _SET_TOOLHEAD_OFFSET]
description = "Internal use only. Sets the toolhead_alignment offset (and hotend_thermal_expansion offset when configured) for the active/dominant toolhead."
gcode = 
	
	{% set move = params.MOVE|default(0)|int %}
	{% set force_toolhead = params.FORCE_TOOLHEAD|default(-1)|int %}
	
	
	{% if params.T is defined %}
	CONSOLE_ECHO TYPE="error" MSG="_SET_TOOLHEAD_OFFSET called with deprectated T parameter, which is ignored."
	{';$_SET_TOOLHEAD_OFFSET_ignoring_TOOLHEAD_parameter'}
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="active/dominant toolhead: {toolhead}, MOVE: {move}, FORCE_TOOLHEAD: {force_toolhead}"
	
	
	{% if force_toolhead >= 0 %}
	{% set toolhead = force_toolhead %}
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="FORCE_TOOLHEAD applied, using TOOLHEAD: {toolhead}"
	{% endif %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set move = 0 %}
	{% endif %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|int %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X=0 Y=0 MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z=0 MOVE={move} SPEED={z_speed}
	{% else %}
	{% set svv = printer.save_variables.variables %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X={(-svv.idex_xoffset)} Y={(-svv.idex_yoffset)} MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-svv.idex_zoffset)} MOVE={move} SPEED={z_speed}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}

[gcode_macro TOOLSHIFT_CONFIG]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={params.SPEED|default(300)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={params.ACCEL|default(5000)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_retraction VALUE={params.RETRACT|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_extrusion VALUE={params.EXTRUDE|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_feedrate VALUE={params.FEEDRATE|default(7200)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={params.Z_HOP|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zspeed VALUE={params.Z_SPEED|default(25)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_combined_zhop VALUE={true if params.COMBINED_ZHOP|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_sync_fans VALUE={true if params.SYNC_FANS|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_prepurging_timer VALUE={params.AUTO_PURGE_TIME|default(0)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_purge VALUE={params.PURGE|default(25)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_standby_temp VALUE={params.STANDBY_TEMP|default(-1)|float}

[gcode_macro CALCULATE_DC_ENDSTOP]
description = "DEPRECATED: This macro has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."
gcode = 
	CONSOLE_ECHO TITLE="CALCULATE_DC_ENDSTOP has been deprecated" TYPE="error" MSG="The CALCULATE_DC_ENDSTOP has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."

[gcode_macro _VAOC]
variable_is_fixed = True
variable_is_started = False
variable_is_started_at_temp = False
variable_additional_safe_distance = 50
variable_safe_z = 30
variable_auto_z_offset_calibration = True
variable_enable_camera_cooling = True
variable_camera_cooling_fan_speed = 0.3
variable_camera_cooling_temperature = 50
variable_toolchange_travel_speed = 300
variable_toolchange_travel_accel = 5000
variable_adjusting_secondary_toolhead_focus_adjusts_zoffset = False
variable_cache_toolchange_travel_speed = 300
variable_cache_toolchange_travel_accel = 5000
variable_cache_toolchange_zhop = 1.0
variable_t0_toolhead_sensor_enabled = 0
variable_t1_toolhead_sensor_enabled = 0
variable_t0_bowden_sensor_enabled = 0
variable_t1_bowden_sensor_enabled = 0
variable_loaded_skew_profile = ""
variable_gcode_z_offset = 0.0
variable_start_x_offset = 0.0
variable_start_y_offset = 0.0
gcode = 
	_ECHO_VAOC_VARS
variable_expected_camera_x_position = 212.5
variable_expected_camera_y_position = 530.5

[gcode_macro _VAOC_START]
description = Called from the front end. If T0_TEMP, T1_TEMP and BED_TEMP parameter are specified, VAOC calibration will start under real conditions at printing temp.
gcode = 
	
	{% set t0_temp = params.T0_TEMP|default(0)|int %}
	{% set t1_temp = params.T1_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(0)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro SKEW_PROFILE"].loaded_profile|default("") %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=loaded_skew_profile VALUE='"{loaded_skew_profile}"'
	
	
	{% if t0_temp > 0 and t1_temp > 0 and bed_temp > 0 %}
	
	
	{% if not is_fixed %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("VAOC calibration at temp works only with a fixed installed VAOC device.") }
	{% endif %}
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE=0
	{% endif %}
	
	
	START_PRINT EXTRUDER_TEMP={t0_temp},{t1_temp} EXTRUDER_OTHER_LAYER_TEMP={t0_temp},{t1_temp} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp} INITIAL_TOOL=0 TOTAL_LAYER_COUNT=1 X0={(printable_x_max / 2 - 10)} Y0={(printable_y_max / 2 - 10)} X1={(printable_x_max / 2 + 10)} Y1={(printable_y_max / 2 + 10)} TOTAL_TOOLSHIFTS=1 FIRST_X={printable_x_max / 2} FIRST_Y={printable_y_max / 2} MIN_X={(printable_x_max / 2 - 10)} MAX_X={(printable_x_max / 2 + 10)} USED_TOOLS=0,1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=True
	
	{% endif %}
	
	
	_START_VAOC

[gcode_macro _START_VAOC]
description = Called from _VAOC_START. Do not call it manually.
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(printable_x_max/2)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(printable_y_max/2)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	DEBUG_ECHO PREFIX="VAOC_START" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, zcontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_x_offset VALUE={svv.idex_xoffset|default(0.0)|float}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_y_offset VALUE={svv.idex_yoffset|default(0.0)|float}
	
	
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_SAFE_Z_HEIGHT
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_speed VALUE={printer["gcode_macro RatOS"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_accel VALUE={printer["gcode_macro RatOS"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_zhop VALUE={printer["gcode_macro RatOS"].toolchange_zhop|float}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE=0
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"START X_REFERENCE:%.6f Y_REFERENCE:%.6f Z_REFERENCE:%.6f PARK_T0:%.6f PARK_T1:%.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, parking_position_t0, parking_position_t1)}
	
	
	_LED_VAOC_ON
	
	
	
	
	
	
	
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=gcode_z_offset VALUE={printer.gcode_move.homing_origin.z}
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z=0
	
	
	MAYBE_HOME
	M400
	
	
	_LOAD_RATOS_SKEW_PROFILE
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	IDEX_SINGLE
	{% endif %}
	
	
	
	SAVE_GCODE_STATE NAME=vaoc_state
	
	
	RESET_NAMED_OFFSET EVENT=reset_all
	
	
	{% if is_fixed %}
	_SELECT_TOOL T=0 TOOLSHIFT=false
	{% if default_toolhead == 0 %}
	G1 X{idex_xcontrolpoint} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint + safe_distance + additional_safe_distance} F{speed}
	{% else %}
	G1 X{idex_xcontrolpoint - safe_distance - additional_safe_distance} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint} F{speed}
	{% endif %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	{% else %}
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	G1 X{idex_xcontrolpoint} F{speed}
	G1 Y{idex_ycontrolpoint} F{speed}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	
	
	_SELECT_TOOL T={default_toolhead} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	{% if not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={default_toolhead}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=True

[gcode_macro _VAOC_END]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_y = printable_y_max / 2 %}
	{% set saved_gcode_z_offset = printer["gcode_macro _VAOC"].gcode_z_offset|default(0.0)|float %}
	
	DEBUG_ECHO PREFIX="_VAOC_END" MSG="printable_y_max: {printable_y_max}, center_y: {center_y}, safe_z: {safe_z}"
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% set x_offset_change = svv.idex_xoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_x_offset|default(0.0)|float %}
	{% set y_offset_change = svv.idex_yoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_y_offset|default(0.0)|float %}
	{% set offset_change_norm = (x_offset_change ** 2 + y_offset_change ** 2) ** 0.5 %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="VAOC calibration changed the relative XY offset between T0 and T1 by {offset_change_norm|round(3)} mm (ΔX: {x_offset_change|round(3)}, ΔY: {y_offset_change|round(3)})"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	G1 Y{center_y} F{speed}
	
	
	_IDEX_SINGLE INIT=1
	
	
	_LED_VAOC_OFF
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={printer["gcode_macro _VAOC"].cache_toolchange_zhop|float}
	
	
	{% if printer["gcode_macro _VAOC"].is_started_at_temp|default(true)|lower == 'true' %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_bowden_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_bowden_sensor_enabled|int}
	{% endif %}
	{% endif %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro _VAOC"].loaded_skew_profile|default("") %}
	{% if loaded_skew_profile != "" %}
	SKEW_PROFILE LOAD={loaded_skew_profile}
	{% else %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=vaoc_state
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z={saved_gcode_z_offset}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False

[gcode_macro _VAOC_LOAD_TOOL]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set auto_temp_offset = true if params.AUTO_TEMP_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set toolhead_zoffset = svv.idex_zoffset|default(0)|float %}
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move T%s to control point: X%.6f Y%.6f Z%.6f IS_FIXED=%s"' % (t, idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, is_fixed)}
	
	
	{% if not auto_temp_offset and not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={t}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	{% set current_z = printer.toolhead.position.z|float %}
	{% set lowest_toolhead_z = [current_z, current_z - toolhead_zoffset]|min %}
	{% if lowest_toolhead_z < safe_z %}
	G1 Z{[safe_z, safe_z + toolhead_zoffset]|max} F{z_speed}
	{% else %}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	{% endif %}
	
	
	_SELECT_TOOL T={t} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_SET_CAMERA_COOLING]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	
	
	{% set enable_camera_cooling = true if printer["gcode_macro _VAOC"].enable_camera_cooling|default(true)|lower == 'true' else false %}
	{% set camera_cooling_temperature = printer["gcode_macro _VAOC"].camera_cooling_temperature|float %}
	{% set camera_cooling_fan_speed = printer["gcode_macro _VAOC"].camera_cooling_fan_speed|float %}
	
	
	{% if printer.heater_bed.temperature >= camera_cooling_temperature and enable_camera_cooling %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={camera_cooling_fan_speed if t == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={camera_cooling_fan_speed if t == 1 else 0}
	
	
	M106.1 S{camera_cooling_fan_speed}
	
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	{% endif %}

[gcode_macro _VAOC_SET_TOOL]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="_VAOC_SET_TOOL" MSG="IDEX_MODE: {idex_mode}, TOOLHEAD: {toolhead}"
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	{% set x = printer.gcode_move.gcode_position.x|float %}
	{% set y = printer.gcode_move.gcode_position.y|float %}
	{% set z = printer.gcode_move.gcode_position.z|float %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE={x}
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE={y}
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE={z}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Control point was set: X%.6f Y%.6f Z%.6f"' % (x, y, z)}
	
	{% else %}
	
	
	
	{% set move_diff_x = printer.gcode_move.gcode_position.x|float - svv.idex_xcontrolpoint|float %}
	{% set move_diff_y = printer.gcode_move.gcode_position.y|float - svv.idex_ycontrolpoint|float %}
	{% set move_diff_z = printer.gcode_move.gcode_position.z|float - svv.idex_zcontrolpoint|float %}
	
	
	{% set new_x_offset = svv.idex_xoffset - move_diff_x %}
	{% set new_y_offset = svv.idex_yoffset - move_diff_y %}
	{% set new_z_offset = svv.idex_zoffset - move_diff_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE={new_x_offset}
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE={new_y_offset}
	
	{% set z_focus_msg = "" %}
	{% if move_diff_z|abs > 1e-6 %}
	{% if printer["gcode_macro _VAOC"].adjusting_secondary_toolhead_focus_adjusts_zoffset|default(false)|lower == 'true' %}
	{% set z_focus_msg = " (Z offset adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={new_z_offset}
	{% else %}
	{% set z_focus_msg = " (Z offset not adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	{% set new_z_offset = svv.idex_zoffset %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset was set: X%.6f Y%.6f Z%.6f%s"' % (toolhead, new_x_offset, new_y_offset, new_z_offset, z_focus_msg)}
	
	{% endif %}

[gcode_macro _VAOC_MOVE]
gcode = 
	
	{% set x = params.X|default(0)|float %}
	{% set y = params.Y|default(0)|float %}
	{% set z = params.Z|default(0)|float %}
	
	
	G91
	{% if z != 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 Z%.6f F300"' % (z)}
	G1 Z{z} F300
	
	{% else %}
	{% if x <=2 and y <=2 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 X%.6f Y%.6f F18000"' % (x, y)}
	G1 X{x} Y{y} F18000
	{% endif %}
	{% endif %}
	G90

[gcode_macro _VAOC_CALIBRATE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	{% if printer["z_offset_probe"] is defined and is_started %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	
	{% if auto_z_offset %}
	_START_VAOC AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_END
	{% else %}
	_VAOC_LOAD_TOOL T={default_toolhead}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	{% endif %}
	
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_Z_OFFSET
	
	{% endif %}

[gcode_macro _VAOC_PROBE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}
	{% if not auto_z_offset %}
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	{% endif %}
	M400
	_VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT

[gcode_macro _VAOC_Z_OFFSET_PROBE_CURRENT_POSITION]
gcode = 
	
	Z_OFFSET_PROBE PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_DROP=1 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median

[gcode_macro _VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT]
gcode = 
	{% if printer["z_offset_probe"] is defined %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE={last_z}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Z-offset control point set:: %.6f"' % last_z}
	
	{% else %}
	
	
	
	{% set z = svv.idex_zoffsetcontrolpoint|float - last_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={z}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-z)}
	
	
	G0 Z{svv.idex_zcontrolpoint|float} F{z_speed}
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset set: Z %.6f"' % (t, z)}
	
	{% endif %}
	
	{% endif %}

[gcode_macro _VAOC_ECHO_Z_OFFSET]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s toolhead z-offset %.6f"' % (1 if default_toolhead == 0 else 0, svv.idex_zoffset)}
	{% if svv.idex_zoffset|abs < 0.02 %}
	CONSOLE_ECHO TITLE={'"Perfect toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="You have a perfect toolhead z-offset!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.02 and svv.idex_zoffset|abs < 0.05 %}
	CONSOLE_ECHO TITLE={'"Good toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is good!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.05 and svv.idex_zoffset|abs < 0.1 %}
	CONSOLE_ECHO TITLE={'"High toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset could be better._N_Use minimum 0.3mm first layer height for copy and mirror mode prints." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.1 and svv.idex_zoffset|abs < 0.2 %}
	CONSOLE_ECHO TITLE={'"Bad toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is bad._N_Copy and mirror mode prints are not recommended with it." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.2 %}
	CONSOLE_ECHO TITLE={'"Unacceptable toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is unacceptable._N_Do not print in copy and mirror mode with it." TYPE="alert"
	{% endif %}
	RATOS_ECHO PREFIX="VAOC" MSG="Toolhead z-offset calibration done!"

[gcode_macro _VAOC_CALIBRATE_TEMP_OFFSET]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if is_fixed and is_started and printer["z_offset_probe"] is defined and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	_VAOC_LOAD_TOOL T={default_toolhead} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_NOZZLE_TEMP_OFFSETS
	
	{% endif %}

[gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET=0
	
	
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	M400

[gcode_macro _VAOC_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(150)|float %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Probing with nozzle temperature {temp}°C..."
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	
	
	G0 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _VAOC_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set msg = '"T0 expansion coefficient %.6fmm_N_T1 expansion coefficient %.6fmm"' % (svv.nozzle_expansion_coefficient_t0, svv.nozzle_expansion_coefficient_t1) %}
	CONSOLE_ECHO TITLE="Nozzle expansion coefficients:" MSG={msg} TYPE="success"

[gcode_macro _VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - expected_camera_x_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC x-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_xcontrolpoint, expected_camera_x_position)) }
	{% endif %}
	{% if (idex_ycontrolpoint - expected_camera_y_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC y-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_ycontrolpoint, expected_camera_y_position)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - printer.gcode_move.gcode_position.x|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected y-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_xcontrolpoint, printer.gcode_move.gcode_position.x|float)) }
	{% endif %}
	{% if (idex_ycontrolpoint - printer.gcode_move.gcode_position.y|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected x-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_ycontrolpoint, printer.gcode_move.gcode_position.y|float)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_SAFE_Z_HEIGHT]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set idex_zoffsetcontrolpoint = svv.idex_zoffsetcontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_SAFE_Z_HEIGHT" MSG={'"idex_zcontrolpoint: %.6f, idex_zoffsetcontrolpoint: %.6f"' % (idex_zcontrolpoint, idex_zoffsetcontrolpoint)}
	
	{% if safe_z < idex_zcontrolpoint + 2 or safe_z < idex_zoffsetcontrolpoint + 2 %}
	{action_raise_error("VAOC safe_z value (%.3f) is too low, it must be higher than %.3f" % (safe_z, [idex_zoffsetcontrolpoint + 2, idex_zcontrolpoint + 2]|max))}
	{% endif %}

[gcode_macro _VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED]
gcode = 
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T0. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T1. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_RESET]
gcode = 
	DEBUG_ECHO PREFIX="_VAOC_RESET" MSG="running template-emitted _VAOC_RESET macro"
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE=212.5
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE=530.5
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE=10
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE=0
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE=0.0
	
	RESET_DC_ENDSTOP_CONFIGURATION
	RESET_Y_MAX_ADJUSTMENT
	
	
	CONSOLE_ECHO TITLE="VAOC Configuration Reset" MSG="VAOC configuration has been reset. You must RESTART klipper for the changes to take effect,_N_then re-calibrate VAOC."

[gcode_macro _ECHO_VAOC_VARS]
description = Echo VAOC variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro _VAOC"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro _VAOC_SWITCH_LED]
gcode = 
	{% if params.STATE|default(0)|int == 1 %}
	_LED_VAOC_ON
	{% else %}
	_LED_VAOC_OFF
	{% endif %}

[gcode_macro Z_PROBE_TEST_T0]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T0
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST_T1]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T1
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	
	
	_VAOC_Z_PROBE_TEST_EVALUATE
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro _VAOC_Z_PROBE_LOOP]
gcode = 
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_SHAKE_IT
	_VAOC_START

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if primary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T0. Retried {primary_retries} time(s)."
	{% endif %}
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	
	{% if (primary_range - secondary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 is drifting significantly more than T1."
	{% endif %}
	{% if (secondary_range - primary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 is drifting significantly more than T0."
	{% endif %}
	
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T0]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T1]
gcode = 
	
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _SHAKE_IT]
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	_Z_HOP
	{% for i in range(3) %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 + 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 + 1}
	{% endfor %}
	{% for i in range(2) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 + 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 + 50}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 1}
	{% endfor %}
	{% endfor %}

[gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 retries updated: {new_retries}"

[gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 retries updated: {new_retries}"

[gcode_macro _CLEAR_PRIMARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _CLEAR_SECONDARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _VAOC_TEST_Z_OFFSET]
gcode = 
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}

[delayed_gcode _IDEX_INIT]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	VERIFY_HYBRID_INVERTED

[gcode_macro Z_TILT_ADJUST]
rename_existing = Z_TILT_ADJUST_ORIG
gcode = 
	
	{% set beacon_contact_z_tilt_adjust_samples = printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust_samples|default(2)|int %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(true)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	_IDEX_SINGLE
	
	_SELECT_TOOL T={printer["gcode_macro RatOS"].default_toolhead|default(0)|int} TOOLSHIFT=false
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_tilt_adjust %}
	Z_TILT_ADJUST_ORIG PROBE_METHOD=contact SAMPLES={beacon_contact_z_tilt_adjust_samples}
	{% else %}
	Z_TILT_ADJUST_ORIG
	{% endif %}
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if idex_mode == "copy" %}
	_IDEX_COPY
	{% elif idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[stepper_x]
position_max = 500
position_endstop = -59.6
position_min = -59.6
step_pin = PF13
dir_pin = x_dir_pin
enable_pin = !PF14
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t0:PA2

[stepper_y]
position_max = 533.65
position_min = -14.35
position_endstop = -14.35
step_pin = PG0
dir_pin = !y_dir_pin
enable_pin = !PF15
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = PG9

[stepper_z]
position_max = 500
position_min = -7
step_pin = PC13
dir_pin = !z0_dir_pin
enable_pin = !PF1
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4
homing_speed = 10
endstop_pin = probe:z_virtual_endstop

[z_tilt]
z_positions = 
	0,0
	250,500
	500,0
points = 
	20, 10
	480, 230
	20, 450
horizontal_move_z = 20
retries = 10
retry_tolerance = 0.02
speed = 600

[extruder]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t0:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t0:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t0:PD3
dir_pin = toolboard_t0:e_dir_pin
enable_pin = !toolboard_t0:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[firmware_retraction]
retract_speed = 60
unretract_extra_length = 0
unretract_speed = 60
retract_length = 0.2

[extruder1]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t1:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t1:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t1:PD3
dir_pin = toolboard_t1:e_dir_pin
enable_pin = !toolboard_t1:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[resonance_tester]
accel_chip_x = lis2dw toolboard_t0
accel_chip_y = lis2dw toolboard_t0
probe_points = 
	250,250,20

[tmc5160 stepper_x]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC4
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 dual_carriage]
stealthchop_threshold = 0
interpolate = True
cs_pin = PF2
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y]
stealthchop_threshold = 0
interpolate = True
cs_pin = PD11
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y1]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC7
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[stepper_y1]
step_pin = PG4
dir_pin = y1_dir_pin
enable_pin = !PA2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46

[tmc2209 stepper_z]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE4
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[tmc2209 stepper_z1]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE1
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z1]
step_pin = PE2
dir_pin = !z1_dir_pin
enable_pin = !PD4
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 stepper_z2]
stealthchop_threshold = 0
interpolate = True
uart_pin = PD3
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z2]
step_pin = PE6
dir_pin = !z2_dir_pin
enable_pin = !PE0
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 extruder]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t0:PB3
run_current = 0.707
sense_resistor = 0.11

[tmc2209 extruder1]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t1:PB3
run_current = 0.707
sense_resistor = 0.11

[beacon]
serial = /dev/beacon
x_offset = 0
y_offset = 27.5
mesh_main_direction = x
mesh_runs = 1
mesh_cluster_size = 0
speed = 15.
lift_speed = 80.
contact_max_hotend_temperature = 275
contact_mesh_min = 20,20
contact_mesh_max = 480,480

[beacon_user_z_offset]

[beacon_mesh]

[beacon_true_zero_correction]

[beacon_adaptive_heat_soak]

[delayed_gcode _BEACON_INIT]
initial_duration = 1
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	_BEACON_MESH_INIT
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_coefficient_multiplier
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_applied_offset
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=beacon_saved_runtime_offset
	{% if printer["gcode_macro RatOS"].beacon_contact_expansion_multiplier is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_contact_expansion_multiplier is no longer used, please remove it from your config file."
	{% endif %}
	{% if printer["gcode_macro RatOS"].beacon_scan_compensation_resolution is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_scan_compensation_resolution is no longer used, please remove it from your config file."
	{% endif %}

[gcode_macro BEACON_RATOS_CALIBRATION]
gcode = 
	RATOS_ECHO MSG="Did you mean BEACON_RATOS_CALIBRATE?"

[gcode_macro BEACON_RATOS_CALIBRATE]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	BEACON_INITIAL_CALIBRATION _AUTOMATED=True
	
	{% if beacon_contact_start_print_true_zero %}
	BEACON_POKE_TEST _AUTOMATED=True
	_BEACON_CHECK_POKE
	{% if printer["dual_carriage"] is not defined %}
	BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET _AUTOMATED=True
	{% endif %}
	{% endif %}
	
	{% set already_heated = False %}
	
	
	{% if beacon_contact_start_print_true_zero and beacon_scan_compensation_enable %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% set already_heated = True %}
	{% endif %}
	
	
	BEACON_FINAL_CALIBRATION _AUTOMATED=True _AUTOMATED_ALREADY_HEATED={already_heated} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	{% if beacon_contact_start_print_true_zero %}
	{% if printer["dual_carriage"] is not defined %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	_BEACON_ECHO_POKE
	{% endif %}
	RATOS_ECHO MSG="Beacon calibration finished!"
	
	
	_LED_BEACON_CALIBRATION_END
	
	
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG

[gcode_macro BEACON_INITIAL_CALIBRATION]
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Initial beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro BEACON_FINAL_CALIBRATION]
description = Runs BEACON_AUTO_CALIBRATE after heating the bed and chamber to specified temperatures. This creates a beacon model under reference conditions for future use.
	This macro will skip calibration if both the beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero settings are enabled, because a new
	model will be calibrated automatically at the start of each print. Use FORCE=True to override this check.
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set already_heated = true if params._AUTOMATED_ALREADY_HEATED|default(false)|lower == 'true' else false %}
	{% set force = params.FORCE|default('false')|lower in ('1', 'true', 'yes') %}
	
	
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default('false')|lower == "true" %}
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero and not force %}
	RATOS_ECHO MSG="BEACON_FINAL_CALIBRATION skipped, not needed because beacon_contact_calibrate_model_on_true_zero is enabled. Use FORCE=True to override."
	{% else %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	{% if chamber_temp > 0 and not already_heated %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	{% if not already_heated %}
	
	G0 Z2.5 F{z_hop_speed}
	
	
	RATOS_ECHO MSG="Waiting for calibration temperature..."
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	{% if beacon_adaptive_heat_soak %}
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,3600]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_Z_HOP
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Final beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	{% endif %}

[gcode_macro BEACON_POKE_TEST]
variable_poke_result_1 = -1
variable_poke_result_2 = -1
variable_poke_result_3 = -1
variable_poke_result_4 = -1
variable_poke_result_5 = -1
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_1 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_2 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_3 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_4 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_5 VALUE=-1
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G0 Z5 F{z_hop_speed}
	
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=1
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=2
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=3
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=4
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=5
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Beacon poke test finished!"
	{% if not automated %}
	_BEACON_ECHO_POKE
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro _BEACON_PROBE_POKE]
gcode = 
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	BEACON_POKE speed=3 top=5 bottom={poke_bottom}
	BEACON_QUERY

[gcode_macro _BEACON_STORE_POKE]
gcode = 
	
	{% set i = params.I|default(1)|int %}
	
	
	{% set last_z = printer.beacon.last_poke_result|default(0)|float %}
	
	
	{% if printer.beacon.last_poke_result|lower != "none" %}
	{% if printer.beacon.last_poke_result.error == 0 %}
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE={"poke_result_%s" % i} VALUE={printer.beacon.last_poke_result.latency}
	{% endif %}
	{% endif %}

[gcode_macro _BEACON_CHECK_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% if p1 == -1 or p2 == -1 or p3 == -1 or p4 == -1 or p5 == -1 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test error!") }
	{% endif %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	{% if avg > 6 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test failed!") }
	{% endif %}

[gcode_macro _BEACON_ECHO_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	
	
	{% if avg <= 1 %}
	{% set type = "success" %}
	{% set note = "Extremely low noise, rarely achieved" %}
	{% elif avg > 1 and avg <= 4 %}
	{% set type = "info" %}
	{% set note = "Excellent performance for a typical printer" %}
	{% elif avg > 4 and avg <= 8 %}
	{% set type = "warning" %}
	{% set note = "Acceptable performance, machine may have considerable cyclic axis noise" %}
	{% elif avg > 8 and avg <= 11 %}
	{% set type = "alert" %}
	{% set note = "Not ideal, may want to verify proper mounting or use thinner stackups" %}
	{% elif avg > 11 %}
	{% set type = "alert" %}
	{% set note = "Reason for concern, present setup may be risky to continue with" %}
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon poke test result:" TYPE={type} MSG={'"Average latency: %.2f_N_%s"' % (avg, note)}

[gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Nozzle temperature offset calibration..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET=0
	
	
	{% if not automated %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing with nozzle temperature {temp}°C..."
	PROBE PROBE_METHOD=contact PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median
	BEACON_QUERY
	
	
	G0 Z5 F{z_speed}

[gcode_macro _BEACON_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer.beacon.last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{default_toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% if default_toolhead == 0 %}
	CONSOLE_ECHO TYPE="info" MSG={'"T0 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t0}
	{% else %}
	CONSOLE_ECHO TYPE="info" MSG={'"T1 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t1}
	{% endif %}

[gcode_macro _BEACON_SET_NOZZLE_TEMP_OFFSET]
description = "Set the thermal expansion z offset for the active toolhead based on the current extruder target temperature and thermal expansion coefficient."
gcode = 
	{% if params.RESET is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The RESET parameter is no longer supported and has no effect."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% if params.TOOLHEAD is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The TOOLHEAD parameter is no longer supported and has no effect. The macro now automatically determines the current toolhead."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	{% if beacon_contact_expansion_compensation %}
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set nozzle_expansion_coefficient_t0 = svv.nozzle_expansion_coefficient_t0|default(0)|float %}
	{% if printer["dual_carriage"] is defined %}
	{% set nozzle_expansion_coefficient_t1 = svv.nozzle_expansion_coefficient_t1|default(0)|float %}
	{% endif %}
	
	
	{% set temp = printer['extruder' if toolhead == 0 else 'extruder1'].target|float %}
	
	
	{% set temp_delta = temp - beacon_contact_true_zero_temp %}
	{% set expansion_coefficient = nozzle_expansion_coefficient_t0 if toolhead == 0 else nozzle_expansion_coefficient_t1 %}
	{% set expansion_offset = temp_delta * (expansion_coefficient / 100) %}
	
	
	SET_NAMED_OFFSET NAME=hotend_thermal_expansion Z={expansion_offset} MOVE=1 MOVE_SPEED={z_speed}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG={'"Nozzle expansion offset of %.6fmm applied to T%s"' % (expansion_offset, toolhead)}
	DEBUG_ECHO PREFIX="_BEACON_SET_NOZZLE_TEMP_OFFSET" MSG="toolhead: {toolhead}, coefficient: {expansion_coefficient|round(6)}, temp_delta: {temp_delta|round(1)},  expansion_offset: {expansion_offset|round(6)}"
	
	{% endif %}

[gcode_macro BEACON_MEASURE_BEACON_OFFSET]
variable_needs_compensation = False
variable_reference_z = 0.0
variable_front = 0.0
variable_front_left = 0.0
variable_front_right = 0.0
variable_back = 0.0
variable_back_left = 0.0
variable_back_right = 0.0
variable_right = 0.0
variable_left = 0.0
variable_margin_x = 40
variable_margin_y = 40
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=False
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Measure beacon offset..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="center"
	
	
	G0 X{margin_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_left"
	
	
	G0 X{safe_home_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front"
	
	
	G0 X{(printable_x_max - margin_x)} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_right"
	
	
	G0 X{safe_home_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back"
	
	
	G0 X{margin_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_left"
	
	
	G0 X{margin_x} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="left"
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_BEACON_ECHO_BEACON_OFFSET
	
	
	_LED_BEACON_CALIBRATION_END
	
	{% endif %}

[gcode_macro _BEACON_STORE_BEACON_OFFSET]
gcode = 
	
	{% set location = params.LOCATION|lower %}
	
	
	{% set last_z = printer.beacon.last_offset_result["delta"]|default(0)|float %}
	
	
	{% if location == "center" %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE={location} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_BEACON_OFFSET]
gcode = 
	
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float * 1000 %}
	{% set front_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_left|default(0)|float * 1000 %}
	{% set front = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front|default(0)|float * 1000 %}
	{% set front_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_right|default(0)|float * 1000 %}
	{% set right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].right|default(0)|float * 1000 %}
	{% set back_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_right|default(0)|float * 1000 %}
	{% set back = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back|default(0)|float * 1000 %}
	{% set back_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_left|default(0)|float * 1000 %}
	{% set left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].left|default(0)|float * 1000 %}
	
	{% set line_1 = "Front left:    %.6fμm" % (front_left) %}
	{% set line_2 = "Front center:  %.6fμm" % (front) %}
	{% set line_3 = "Front right:   %.6fμm" % (front_right) %}
	{% set line_4 = "Left center:   %.6fμm" % (left) %}
	{% set line_5 = "Right center:  %.6fμm" % (right) %}
	{% set line_6 = "Back left:     %.6fμm" % (back_left) %}
	{% set line_7 = "Back center:   %.6fμm" % (back) %}
	{% set line_8 = "Back right:    %.6fμm" % (back_right) %}
	
	{% set max_value = [(front_left|abs), (front|abs), (front_right|abs), (left|abs), (right|abs), (back_left|abs), (back|abs), (back_right|abs)]|max %}
	{% if max_value <= 50 %}
	{% set type = "success" %}
	{% set recommendation = "Very low beacon offset: %.6fμm._N_No beacon scan compensation needed." % max_value %}
	{% elif max_value > 50 and max_value <= 100 %}
	{% set type = "info" %}
	{% set recommendation = "Low beacon offset: %.6fμm._N_You may experience first layer inconsistensies, consider beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 100 and max_value <= 150 %}
	{% set type = "warning" %}
	{% set recommendation = "High beacon offset: %.6fμm._N_High chance of first layer problems, beacon scan compensation is highly encouraged." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 150 and max_value <= 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Very High beacon offset: %.6fμm._N_You will encounter first layer problems on large prints unless you activate beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Extremely high beacon offset: %.6fμm._N_You have significant scan/contact inconsistency which is indicative of mechanical problems, please investigate before resorting to software compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon offset relative to the center" TYPE={type} MSG={'"_N_%s_N__N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s"' % (recommendation, line_1, line_2, line_3, line_4, line_5, line_6, line_7, line_8)}

[gcode_macro BEACON_CREATE_SCAN_COMPENSATION_MESH]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set profile = params.PROFILE|default("auto")|string %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set keep_temp_meshes = params.KEEP_TEMP_MESHES|default(0) %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' %}
	{% set desired_spacing = printer["gcode_macro RatOS"].beacon_scan_compensation_desired_spacing|float %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	
	{% if not beacon_scan_compensation_enable %}
	RATOS_ECHO MSG="Beacon scan compensation is disabled!"
	
	{% else %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	
	
	RATOS_ECHO MSG="Please wait..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	G1 Z2.5 F{z_speed}
	{% if beacon_adaptive_heat_soak %}
	
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,9000]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if not (beacon_adaptive_heat_soak or bed_heat_soak_time > 0) %}
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if printer.z_tilt is defined %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% endif %}
	{% if printer.quad_gantry_level is defined %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% endif %}
	
	
	_BEACON_CREATE_SCAN_COMPENSATION_MESH_CORE PROFILE="{profile}" DESIRED_SPACING={desired_spacing} CHAMBER_TEMP={chamber_temp} KEEP_TEMP_MESHES={keep_temp_meshes}
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	{% if automated %}
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon scan compensation mesh created!"
	
	
	{% if not automated %}
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED]
gcode = 
	
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED" MSG="beacon_scan_compensation_profile {beacon_scan_compensation_profile}, beacon_scan_compensation_enable {beacon_scan_compensation_enable}"
	
	{% if beacon_scan_compensation_enable %}
	BEACON_APPLY_SCAN_COMPENSATION PROFILE="{beacon_scan_compensation_profile}"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL]
gcode = 
	
	{% set beacon_contact_start_print_true_zero = params.BEACON_CONTACT_START_PRINT_TRUE_ZERO|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = params.beacon_contact_calibrate_model_on_true_zero|lower == 'true' %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and not printer.beacon.model %}
	{% set beacon_model_required_for_true_zero = beacon_contact_start_print_true_zero and not beacon_contact_calibrate_model_on_true_zero %}
	{% set beacon_model_required_for_homing =
	printer.fastconfig.settings.stepper_z.endstop_pin == 'probe:z_virtual_endstop'
	and (( printer.fastconfig.settings.beacon.home_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower != 'true')
	or ( printer.fastconfig.settings.beacon.default_probe_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower != 'true' )) %}
	{% if beacon_model_required_for_homing or beacon_model_required_for_true_zero %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("An active Beacon model is required. Have you performed initial Beacon calibration?") }
	{% endif %}
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION]
gcode = 
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set bed_temp_mismatch_is_error = true if printer["gcode_macro RatOS"].beacon_scan_compensation_bed_temp_mismatch_is_error|default(false)|lower == 'true' else false %}
	
	{% set bed_temp = params.BED_TEMP|default(0)|float %}
	{% if bed_temp == 0 %}
	{% set bed_temp = printer.heater_bed.temperature %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_PREFLIGHT_CHECK_BEACON" MSG="beacon_scan_compensation_profile={beacon_scan_compensation_profile}, beacon_scan_compensation_enable={beacon_scan_compensation_enable}, bed_temp={bed_temp}"
	
	{% if beacon_scan_compensation_enable %}
	_VALIDATE_COMPENSATION_MESH_PROFILE PROFILE="{beacon_scan_compensation_profile}" TITLE="Check Beacon scan compensation profile" SUBJECT="Configured compensation profile '{beacon_scan_compensation_profile}'" COMPARE_BED_TEMP={bed_temp} COMPARE_BED_TEMP_IS_ERROR={bed_temp_mismatch_is_error}
	{% endif %}

[gcode_macro _BEACON_MAYBE_SCAN_COMPENSATION]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set needs_scan_compensation = true if printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].needs_compensation|default(false)|lower == 'true' else false %}
	
	{% if needs_scan_compensation %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% endif %}

[gcode_macro _BEACON_HOME_AND_ABL]
gcode = 
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	{% if needs_rehoming %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}

[gcode_macro SAVE_Z_OFFSET]
description = Deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead, or in Mainsail use the SAVE button in the Z-OFFSET section.
gcode = 
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default('false')|lower == 'true' %}
	{% set msg = "SAVE_Z_OFFSET is deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead,_N_or in Mainsail use the SAVE button in the Z-OFFSET section."%}
	{% if not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% set msg = msg + "_N_You must then use the SAVE_CONFIG command to persist the change." %}
	{% endif %}
	CONSOLE_ECHO TYPE="error" MSG="{msg}"

[gcode_macro _BEACON_OFFSET_COMPARE]
gcode = 
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing..."
	
	
	BEACON_OFFSET_COMPARE SAMPLES_DROP=1 SAMPLES=3
	BEACON_QUERY

[fan]
pin = rpi:gpio4

[fan_generic part_fan_t0]
pin = PA8
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[fan_generic part_fan_t1]
pin = PE5
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[heater_fan toolhead_cooling_fan_t0]
heater = extruder
shutdown_speed = 1
pin = toolboard_t0:PB4

[heater_fan toolhead_cooling_fan_t1]
heater = extruder1
shutdown_speed = 1
pin = toolboard_t1:PB4

[controller_fan controller_fan]
pin = dinghy:PA4
tachometer_pin = dinghy:PC15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[z_offset_probe]
pin = ^PG10
z_offset = -7
y_offset = 0
x_offset = 37.5
speed = 10
samples = 3
sample_retract_dist = 5
lift_speed = 10.0
samples_result = median
samples_tolerance = 0.2
samples_tolerance_retries = 5

[neopixel vaoc_led]
pin = PB10
chain_count = 6
color_order = GRB

[heater_fan vaoc_fan]
pin = PD13
heater = heater_bed
fan_speed = 1.0
heater_temp = 50

[fan_generic filter]
pin = !PD14
enable_pin = PD15

[gcode_macro T0]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = True
variable_color = "7bff33"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = -32.6
variable_parking_position = -57.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=0 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[gcode_macro T1]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = False
variable_color = "0ea5e9"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = 532.6
variable_parking_position = 557.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=1 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[save_variables]
filename = /home/pi/printer_data/config/ratos-variables.cfg

[mcu dinghy]
serial = /dev/serial/by-id/usb-Klipper_stm32f072xb_Dragon_dinghy-if00

[temperature_sensor th0]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA0

[temperature_sensor th1]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA1

[temperature_sensor th2]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA2

[temperature_sensor th3]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA3

[controller_fan CTL2]
pin = dinghy:PB14
tachometer_pin = dinghy:PB15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[mcu plasma]
serial = /dev/serial/by-id/usb-Klipper_rp2040_Plasma-if00

[neopixel Chamber_Lights]
pin = plasma:gpio15
chain_count = 140
color_order = GRBW
initial_red = 0.0
initial_green = 0.0
initial_blue = 0.0
initial_white = 0.1

[beacon model default]
model_coef = 1.5287863993594841,
	1.9289099639750602,
	0.8838828622507556,
	0.25554883784260735,
	-0.015171504024913506,
	0.3044946127013882,
	0.15820427856566457,
	-0.25262403959326246,
	0.042488512846660914,
	0.16662470122520964
model_domain = 1.842634574664148e-07,1.9339206373083917e-07
model_range = 0.200000,5.000000
model_temp = 13.222247
model_offset = 0.00000

[bed_mesh default]
version = 1
points = 
	0.016163, 0.016713, 0.001923, -0.017658, -0.031574, -0.032498, -0.030898, -0.032177, -0.035213, -0.031148, -0.021322, -0.016924, -0.015012, -0.013911, -0.012197, -0.012583, -0.010489, -0.007529, -0.003986, -0.000980, 0.005518, 0.014442, 0.027426, 0.034677, 0.037410, 0.040391, 0.041842, 0.040369, 0.037615, 0.030776, 0.027664, 0.022856, 0.016892, 0.015398, 0.014717, 0.006921, 0.001532, 0.000731, 0.008657, 0.014036
	0.005356, -0.005066, -0.016998, -0.029668, -0.038334, -0.043672, -0.041139, -0.042488, -0.045199, -0.039432, -0.028746, -0.023642, -0.024058, -0.022802, -0.019679, -0.018514, -0.018102, -0.016476, -0.012722, -0.010077, -0.001809, 0.007180, 0.019853, 0.027754, 0.029964, 0.033626, 0.036783, 0.032018, 0.029372, 0.020847, 0.017634, 0.011926, 0.009013, 0.009254, 0.007972, -0.001380, -0.006940, -0.002160, 0.006135, 0.008330
	-0.004900, -0.006720, -0.021914, -0.039691, -0.050459, -0.050377, -0.046281, -0.048755, -0.054708, -0.051499, -0.033927, -0.027632, -0.030243, -0.031447, -0.024387, -0.021408, -0.020382, -0.018068, -0.015930, -0.013877, -0.006099, 0.003479, 0.013310, 0.024783, 0.025522, 0.030849, 0.033573, 0.031409, 0.025495, 0.016683, 0.011264, 0.008805, 0.006856, 0.008059, 0.007305, 0.002581, -0.003320, -0.003239, 0.004691, 0.010045
	-0.008791, -0.019334, -0.029149, -0.040533, -0.051698, -0.058235, -0.054863, -0.054840, -0.055692, -0.049534, -0.036731, -0.033053, -0.035667, -0.035315, -0.024352, -0.023825, -0.022538, -0.020438, -0.018207, -0.015389, -0.006515, 0.001966, 0.013591, 0.019434, 0.020600, 0.024967, 0.029425, 0.026812, 0.018980, 0.007878, 0.002360, 0.000859, 0.003849, 0.005649, 0.005421, -0.000416, -0.007906, -0.003164, 0.007582, 0.010039
	-0.018512, -0.018210, -0.033932, -0.050501, -0.061588, -0.064139, -0.060236, -0.062528, -0.067065, -0.062039, -0.045815, -0.039448, -0.040521, -0.042080, -0.033870, -0.030878, -0.027396, -0.024548, -0.021298, -0.020041, -0.011880, -0.002847, 0.008689, 0.015857, 0.015934, 0.018697, 0.022439, 0.022106, 0.017916, 0.005879, 0.001037, -0.001311, -0.001335, 0.001897, 0.003656, 0.000561, -0.006084, -0.005683, 0.000338, 0.006245
	-0.028558, -0.036721, -0.044680, -0.054969, -0.066140, -0.075045, -0.073515, -0.073161, -0.075696, -0.068963, -0.058892, -0.053111, -0.050990, -0.048040, -0.041262, -0.037419, -0.034866, -0.031845, -0.029787, -0.026524, -0.017896, -0.009322, -0.001010, 0.005819, 0.008058, 0.010456, 0.013266, 0.012529, 0.007992, -0.001491, -0.006769, -0.009303, -0.005980, -0.003567, -0.003340, -0.011496, -0.018818, -0.014808, -0.004181, -0.000733
	-0.037253, -0.038393, -0.053129, -0.066170, -0.075959, -0.079233, -0.077475, -0.082688, -0.086779, -0.083983, -0.069005, -0.062542, -0.060351, -0.058481, -0.051101, -0.043149, -0.039837, -0.037039, -0.034698, -0.031301, -0.024330, -0.019786, -0.010285, -0.001967, 0.002812, 0.004899, 0.009657, 0.006946, 0.002155, -0.005232, -0.009851, -0.011218, -0.011509, -0.010097, -0.010293, -0.013175, -0.018958, -0.019846, -0.012107, -0.005641
	-0.046584, -0.055590, -0.062606, -0.069218, -0.080399, -0.087414, -0.089037, -0.092376, -0.095115, -0.088957, -0.080802, -0.073290, -0.068741, -0.064591, -0.054452, -0.048270, -0.045916, -0.044559, -0.042047, -0.039605, -0.032667, -0.025789, -0.019495, -0.012773, -0.006697, -0.003025, 0.001413, 0.000817, -0.004738, -0.013008, -0.017605, -0.018191, -0.018524, -0.016356, -0.016750, -0.021992, -0.028943, -0.025791, -0.016146, -0.010447
	-0.051029, -0.051677, -0.068218, -0.079622, -0.088590, -0.089331, -0.089731, -0.096072, -0.105329, -0.100771, -0.087584, -0.079320, -0.075489, -0.072081, -0.064183, -0.054662, -0.048601, -0.049465, -0.047050, -0.045011, -0.040009, -0.032508, -0.025212, -0.018144, -0.011996, -0.008136, -0.003187, -0.003214, -0.006646, -0.013044, -0.019446, -0.020615, -0.022270, -0.021298, -0.020215, -0.020946, -0.026034, -0.026598, -0.021025, -0.012328
	-0.057184, -0.064908, -0.073093, -0.081584, -0.091971, -0.097048, -0.097688, -0.101869, -0.106651, -0.102162, -0.095658, -0.087938, -0.082718, -0.077017, -0.069608, -0.060682, -0.056889, -0.056864, -0.054260, -0.052011, -0.044563, -0.038927, -0.031943, -0.025832, -0.021170, -0.014319, -0.009046, -0.008543, -0.011751, -0.020287, -0.026608, -0.027259, -0.029120, -0.025549, -0.023221, -0.027725, -0.032477, -0.028427, -0.019343, -0.014932
	-0.060411, -0.062241, -0.080781, -0.090744, -0.100903, -0.099702, -0.098468, -0.104236, -0.116853, -0.112701, -0.102623, -0.095036, -0.091407, -0.089871, -0.079701, -0.070222, -0.064325, -0.063875, -0.062248, -0.059396, -0.052699, -0.047589, -0.041526, -0.028442, -0.024526, -0.019549, -0.015403, -0.014251, -0.017989, -0.022824, -0.027328, -0.029155, -0.033315, -0.032426, -0.027619, -0.030776, -0.033688, -0.032458, -0.027219, -0.019649
	-0.067541, -0.076514, -0.082321, -0.088656, -0.099968, -0.104930, -0.105875, -0.109051, -0.115531, -0.112996, -0.105760, -0.100390, -0.096171, -0.090011, -0.080050, -0.073632, -0.067451, -0.067031, -0.065225, -0.062471, -0.056370, -0.050129, -0.041626, -0.030801, -0.027579, -0.022472, -0.014826, -0.015306, -0.020316, -0.025953, -0.030661, -0.034103, -0.035502, -0.032738, -0.031311, -0.037314, -0.041306, -0.035280, -0.027449, -0.020395
	-0.068162, -0.069269, -0.088235, -0.096809, -0.103385, -0.103271, -0.102507, -0.109535, -0.123412, -0.118580, -0.106622, -0.099580, -0.097644, -0.096978, -0.087259, -0.077196, -0.068978, -0.067016, -0.063682, -0.062548, -0.057901, -0.052295, -0.044088, -0.032703, -0.026551, -0.021607, -0.014155, -0.013747, -0.017390, -0.022419, -0.027444, -0.030877, -0.033450, -0.032423, -0.032041, -0.033598, -0.035149, -0.034054, -0.029356, -0.020998
	-0.069473, -0.075924, -0.083569, -0.089648, -0.101235, -0.105828, -0.109144, -0.112613, -0.117233, -0.114186, -0.107090, -0.098616, -0.097084, -0.094257, -0.086773, -0.076409, -0.069532, -0.066472, -0.060956, -0.059191, -0.052886, -0.047752, -0.041275, -0.032437, -0.027780, -0.020398, -0.012061, -0.010133, -0.014056, -0.021528, -0.027924, -0.030605, -0.030609, -0.026068, -0.029346, -0.033991, -0.038254, -0.030610, -0.021109, -0.015885
	-0.068084, -0.066409, -0.083944, -0.094013, -0.102504, -0.105274, -0.106036, -0.112090, -0.121664, -0.117824, -0.104850, -0.097467, -0.098833, -0.098622, -0.089603, -0.078147, -0.068143, -0.066300, -0.061573, -0.057727, -0.054825, -0.048625, -0.040164, -0.030532, -0.025948, -0.020264, -0.014196, -0.010702, -0.013794, -0.019775, -0.026095, -0.028838, -0.030254, -0.027944, -0.027980, -0.030915, -0.032446, -0.028861, -0.023732, -0.014676
	-0.065280, -0.068669, -0.076948, -0.082397, -0.094986, -0.105117, -0.107099, -0.108954, -0.112557, -0.110326, -0.100725, -0.096325, -0.096240, -0.092388, -0.081185, -0.071682, -0.065650, -0.062250, -0.057027, -0.054691, -0.048349, -0.042069, -0.032712, -0.027728, -0.023396, -0.018458, -0.008357, -0.005699, -0.011447, -0.020033, -0.026387, -0.030280, -0.028443, -0.023735, -0.023838, -0.031580, -0.034204, -0.027768, -0.018029, -0.010628
	-0.061662, -0.057052, -0.075163, -0.086710, -0.094182, -0.097544, -0.098814, -0.105908, -0.114460, -0.111718, -0.097559, -0.091614, -0.093860, -0.093098, -0.081687, -0.069410, -0.064117, -0.062745, -0.055603, -0.051413, -0.048043, -0.040363, -0.031842, -0.023420, -0.017470, -0.012600, -0.008163, -0.003898, -0.007635, -0.013254, -0.019807, -0.025153, -0.027074, -0.023513, -0.023727, -0.028669, -0.029153, -0.024831, -0.018735, -0.009246
	-0.056176, -0.059439, -0.066501, -0.071527, -0.085216, -0.094918, -0.097595, -0.099419, -0.101847, -0.102015, -0.093849, -0.089867, -0.088840, -0.083167, -0.071832, -0.062522, -0.058023, -0.057771, -0.053050, -0.048285, -0.041374, -0.033527, -0.024473, -0.018428, -0.013958, -0.008161, -0.001196, 0.001754, -0.004016, -0.011132, -0.018325, -0.021813, -0.021514, -0.016948, -0.018061, -0.025702, -0.028671, -0.021470, -0.011028, -0.001934
	-0.059202, -0.050525, -0.065461, -0.076792, -0.084156, -0.088538, -0.090719, -0.096070, -0.105729, -0.105136, -0.090350, -0.083865, -0.087807, -0.086145, -0.074773, -0.064235, -0.057641, -0.055896, -0.051286, -0.046566, -0.042431, -0.034723, -0.023762, -0.014983, -0.009126, -0.004877, 0.000094, 0.003492, -0.000931, -0.005883, -0.011665, -0.015251, -0.016432, -0.016119, -0.015373, -0.018827, -0.019994, -0.017564, -0.012298, 0.002094
	-0.055561, -0.058184, -0.062669, -0.068111, -0.080741, -0.091895, -0.093911, -0.094387, -0.100239, -0.100695, -0.089841, -0.085682, -0.085212, -0.082910, -0.073072, -0.063594, -0.056157, -0.053482, -0.048107, -0.045405, -0.039982, -0.029777, -0.019905, -0.013872, -0.009732, -0.004272, 0.003500, 0.006909, 0.001302, -0.004626, -0.012374, -0.014751, -0.014637, -0.011794, -0.012913, -0.018244, -0.023377, -0.018086, -0.006575, 0.003294
	-0.062834, -0.047300, -0.060870, -0.073023, -0.079303, -0.082121, -0.083623, -0.091321, -0.100996, -0.098896, -0.085406, -0.078881, -0.081932, -0.082077, -0.074409, -0.063158, -0.053822, -0.050328, -0.045077, -0.039678, -0.035825, -0.028532, -0.017793, -0.009121, -0.003444, -0.000905, 0.003990, 0.007745, 0.004595, 0.000143, -0.004555, -0.007411, -0.010850, -0.010100, -0.010079, -0.013177, -0.016434, -0.014663, -0.010248, -0.000213
	-0.054748, -0.053907, -0.057576, -0.063118, -0.072478, -0.081366, -0.084424, -0.086348, -0.089718, -0.089305, -0.081771, -0.076889, -0.076923, -0.073518, -0.067973, -0.057643, -0.050848, -0.046966, -0.041560, -0.036436, -0.029233, -0.020685, -0.010240, -0.004935, -0.001084, 0.002478, 0.009168, 0.014038, 0.010885, 0.004752, -0.001650, -0.004209, -0.003998, -0.002336, -0.003784, -0.010930, -0.016480, -0.012798, -0.003650, 0.002998
	-0.059345, -0.041989, -0.057435, -0.068229, -0.072857, -0.072586, -0.075155, -0.083286, -0.091292, -0.089727, -0.073702, -0.068353, -0.072910, -0.073863, -0.065527, -0.053635, -0.046064, -0.043899, -0.037607, -0.031251, -0.026194, -0.018885, -0.008095, 0.000309, 0.004911, 0.007046, 0.010642, 0.015635, 0.015277, 0.012612, 0.008074, 0.004852, 0.001546, 0.000504, 0.000589, -0.002769, -0.006432, -0.007765, -0.005391, 0.006950
	-0.050324, -0.049088, -0.052417, -0.057257, -0.063818, -0.071057, -0.074636, -0.075459, -0.079445, -0.077368, -0.068788, -0.063940, -0.065040, -0.063419, -0.054864, -0.044910, -0.038774, -0.036951, -0.031149, -0.026080, -0.018383, -0.011985, -0.001732, 0.003893, 0.007180, 0.011120, 0.017429, 0.021738, 0.019167, 0.015812, 0.011027, 0.007243, 0.006720, 0.009346, 0.006598, -0.003776, -0.009199, -0.007592, 0.005481, 0.014396
	-0.058437, -0.035937, -0.050762, -0.060425, -0.061123, -0.059090, -0.062399, -0.072124, -0.080338, -0.074950, -0.060985, -0.054754, -0.059333, -0.060500, -0.051714, -0.038834, -0.031117, -0.031693, -0.025186, -0.017982, -0.014316, -0.010137, 0.000228, 0.008774, 0.014018, 0.016470, 0.019918, 0.022071, 0.021109, 0.019957, 0.018698, 0.015803, 0.013135, 0.011136, 0.008719, 0.003522, -0.000994, 0.000525, 0.006297, 0.018454
	-0.046143, -0.041577, -0.045391, -0.046668, -0.051722, -0.057607, -0.062802, -0.065205, -0.068243, -0.066293, -0.058216, -0.051324, -0.051806, -0.051018, -0.043393, -0.032431, -0.024016, -0.023321, -0.018504, -0.013897, -0.008455, -0.001123, 0.006609, 0.010462, 0.013887, 0.019328, 0.024804, 0.026590, 0.023420, 0.020337, 0.017129, 0.017199, 0.016391, 0.015616, 0.013257, 0.005832, -0.000019, 0.003462, 0.014308, 0.023624
	-0.051989, -0.030294, -0.043380, -0.051339, -0.050711, -0.048193, -0.052258, -0.061218, -0.070507, -0.068810, -0.049476, -0.042352, -0.046018, -0.046673, -0.038670, -0.027263, -0.018137, -0.018587, -0.013603, -0.008482, -0.004647, -0.000011, 0.008230, 0.015652, 0.019436, 0.023069, 0.024762, 0.027750, 0.028115, 0.026227, 0.022220, 0.023166, 0.020341, 0.018455, 0.014918, 0.011932, 0.007138, 0.008523, 0.014718, 0.026201
	-0.041448, -0.035286, -0.036538, -0.037577, -0.044652, -0.049300, -0.051092, -0.052841, -0.058068, -0.056947, -0.046235, -0.038436, -0.037494, -0.034175, -0.028932, -0.016904, -0.010075, -0.010552, -0.004464, -0.001243, 0.003236, 0.010200, 0.015604, 0.020362, 0.023157, 0.028023, 0.032826, 0.035958, 0.034819, 0.030600, 0.025988, 0.026013, 0.026284, 0.025661, 0.022322, 0.013336, 0.006464, 0.011312, 0.022330, 0.031668
	-0.048540, -0.022534, -0.035260, -0.042156, -0.042749, -0.037408, -0.038818, -0.047322, -0.056808, -0.053643, -0.035691, -0.027822, -0.028789, -0.028255, -0.020274, -0.007285, -0.000723, -0.000788, 0.005440, 0.008938, 0.008953, 0.012074, 0.017957, 0.025241, 0.029175, 0.032057, 0.033733, 0.038359, 0.039349, 0.037161, 0.034052, 0.034585, 0.032020, 0.029940, 0.026326, 0.024577, 0.020432, 0.021586, 0.024568, 0.034552
	-0.033086, -0.027982, -0.029443, -0.029011, -0.035629, -0.040579, -0.038290, -0.037389, -0.041260, -0.040430, -0.032279, -0.021394, -0.018817, -0.015525, -0.007558, 0.006345, 0.011048, 0.011271, 0.013497, 0.017030, 0.017449, 0.022752, 0.026764, 0.030722, 0.033532, 0.037203, 0.043356, 0.048536, 0.047776, 0.043851, 0.039311, 0.039944, 0.039954, 0.038931, 0.034893, 0.030946, 0.023127, 0.027359, 0.034859, 0.043920
	-0.036218, -0.016846, -0.030897, -0.036980, -0.037261, -0.033334, -0.030888, -0.034074, -0.042142, -0.039980, -0.021377, -0.013603, -0.014171, -0.013131, -0.001768, 0.014998, 0.020060, 0.018173, 0.019934, 0.024704, 0.023739, 0.024617, 0.027288, 0.035116, 0.041187, 0.043128, 0.045921, 0.051709, 0.053031, 0.050698, 0.047697, 0.047728, 0.046845, 0.043201, 0.041805, 0.040728, 0.036184, 0.034435, 0.035120, 0.045329
	-0.029808, -0.023871, -0.026541, -0.026705, -0.031203, -0.036908, -0.034411, -0.029231, -0.028090, -0.026102, -0.016691, -0.007747, -0.004471, 0.001560, 0.010738, 0.025062, 0.027672, 0.024833, 0.026976, 0.029502, 0.030754, 0.035709, 0.039403, 0.044719, 0.046379, 0.049250, 0.054178, 0.059793, 0.059542, 0.052111, 0.047608, 0.050103, 0.053142, 0.052747, 0.050045, 0.044102, 0.033149, 0.035392, 0.045678, 0.054080
	-0.032238, -0.008993, -0.023999, -0.030969, -0.028658, -0.024887, -0.024493, -0.028088, -0.031053, -0.022849, -0.003868, 0.004647, 0.004540, 0.007560, 0.018373, 0.031401, 0.035778, 0.033768, 0.035173, 0.035884, 0.036597, 0.038940, 0.044566, 0.053914, 0.056554, 0.056382, 0.056449, 0.060387, 0.062696, 0.058223, 0.055016, 0.056193, 0.056891, 0.052793, 0.052741, 0.052626, 0.048117, 0.045032, 0.048033, 0.055100
	-0.019758, -0.015110, -0.017814, -0.018871, -0.023340, -0.028653, -0.026880, -0.018681, -0.017020, -0.011343, -0.001002, 0.008249, 0.014012, 0.020367, 0.026878, 0.038534, 0.041827, 0.039532, 0.039775, 0.039109, 0.043172, 0.049325, 0.056604, 0.059583, 0.059329, 0.059876, 0.062766, 0.068759, 0.067214, 0.059657, 0.055950, 0.056798, 0.058619, 0.058591, 0.059849, 0.056473, 0.046841, 0.047921, 0.058342, 0.065346
	-0.018628, -0.000296, -0.014764, -0.022634, -0.020483, -0.016362, -0.015485, -0.017352, -0.020246, -0.010362, 0.008635, 0.018414, 0.018542, 0.024258, 0.033370, 0.045728, 0.049983, 0.044610, 0.044638, 0.047649, 0.049220, 0.051954, 0.058932, 0.065915, 0.069102, 0.067410, 0.067680, 0.073734, 0.072203, 0.067293, 0.063945, 0.064378, 0.065047, 0.061989, 0.062882, 0.063468, 0.059707, 0.057986, 0.059739, 0.066139
	-0.010091, -0.006551, -0.008018, -0.009589, -0.016068, -0.020662, -0.019451, -0.010985, -0.009391, -0.003580, 0.007826, 0.019598, 0.024961, 0.033762, 0.040618, 0.050868, 0.052139, 0.050495, 0.049198, 0.051777, 0.056840, 0.061771, 0.068414, 0.072295, 0.073443, 0.072145, 0.073414, 0.079338, 0.075988, 0.067367, 0.064745, 0.064435, 0.066982, 0.065811, 0.067424, 0.063230, 0.058438, 0.059982, 0.067672, 0.072460
	-0.016254, 0.006291, -0.008031, -0.013944, -0.014475, -0.010741, -0.009932, -0.011709, -0.015503, -0.006971, 0.013190, 0.024865, 0.029121, 0.033942, 0.044335, 0.054572, 0.058078, 0.055224, 0.055897, 0.058327, 0.061207, 0.063939, 0.070506, 0.078141, 0.084203, 0.081223, 0.079519, 0.082883, 0.080890, 0.076174, 0.071279, 0.073064, 0.071225, 0.066859, 0.069860, 0.070836, 0.069427, 0.069140, 0.070950, 0.075269
	-0.008127, 0.000730, 0.001164, -0.000308, -0.006659, -0.012343, -0.011463, -0.003755, -0.001876, 0.005166, 0.016616, 0.030243, 0.036509, 0.045020, 0.053681, 0.063738, 0.066425, 0.063964, 0.062796, 0.065633, 0.071912, 0.077280, 0.082580, 0.086477, 0.089798, 0.089603, 0.091453, 0.096125, 0.088708, 0.079903, 0.074317, 0.076190, 0.075399, 0.075242, 0.079628, 0.077855, 0.071473, 0.073702, 0.082757, 0.088086
	-0.010951, 0.013218, -0.000878, -0.006241, -0.005623, 0.000046, 0.000158, -0.002943, -0.005314, 0.005491, 0.026890, 0.035754, 0.041490, 0.045829, 0.059325, 0.070249, 0.074114, 0.071815, 0.073229, 0.076313, 0.080778, 0.081554, 0.087919, 0.096206, 0.101562, 0.101674, 0.100494, 0.103989, 0.100292, 0.093977, 0.088080, 0.088136, 0.086555, 0.081494, 0.084966, 0.087073, 0.084113, 0.085184, 0.087700, 0.092188
	-0.002972, 0.006020, 0.006098, 0.004303, 0.001326, -0.002386, -0.001840, 0.005325, 0.008624, 0.016246, 0.026781, 0.039696, 0.048540, 0.055938, 0.066982, 0.076497, 0.080828, 0.079669, 0.080127, 0.083754, 0.089783, 0.093456, 0.100570, 0.105322, 0.107132, 0.110571, 0.113141, 0.118064, 0.111721, 0.101634, 0.093555, 0.093112, 0.093104, 0.092325, 0.094780, 0.092552, 0.085283, 0.088882, 0.097508, 0.105280
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 11.4
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Preperations]
version = 1
points = 
	0.012158, -0.006098, -0.020628, -0.034069, -0.049418, -0.058491, -0.062706, -0.063181, -0.065552, -0.063461, -0.057373, -0.056717, -0.056579, -0.054080, -0.053373, -0.056878, -0.057281, -0.055224, -0.049676, -0.047605, -0.041454, -0.034605, -0.022490, -0.011292, -0.009411, -0.005344, -0.003510, -0.002717, -0.005999, -0.010712, -0.013141, -0.015611, -0.020004, -0.017667, -0.016629, -0.022248, -0.024864, -0.024065, -0.014921, -0.010826
	-0.005958, -0.021084, -0.033800, -0.047903, -0.059950, -0.071345, -0.072502, -0.073350, -0.075852, -0.072963, -0.067236, -0.064315, -0.065698, -0.064338, -0.062871, -0.065238, -0.067095, -0.063584, -0.059241, -0.057846, -0.051380, -0.043157, -0.030230, -0.019950, -0.018121, -0.014291, -0.009354, -0.013065, -0.016464, -0.022925, -0.025337, -0.026541, -0.030577, -0.029068, -0.027094, -0.030532, -0.034241, -0.032625, -0.021498, -0.020513
	-0.017526, -0.027763, -0.040710, -0.055305, -0.068172, -0.079641, -0.081247, -0.081903, -0.083679, -0.081855, -0.073270, -0.070340, -0.072083, -0.071536, -0.066055, -0.065901, -0.069085, -0.066531, -0.063284, -0.061616, -0.053366, -0.047292, -0.035451, -0.023167, -0.022205, -0.016699, -0.012552, -0.014153, -0.018802, -0.030443, -0.032210, -0.034051, -0.034437, -0.031439, -0.030406, -0.032817, -0.036351, -0.034849, -0.024250, -0.019489
	-0.017750, -0.030284, -0.043463, -0.055839, -0.071865, -0.084888, -0.086157, -0.084619, -0.086681, -0.084515, -0.075246, -0.073263, -0.075604, -0.075123, -0.069177, -0.070723, -0.071097, -0.068644, -0.065465, -0.063718, -0.057574, -0.049335, -0.036556, -0.028418, -0.028259, -0.023387, -0.018454, -0.020519, -0.027499, -0.038314, -0.041534, -0.041886, -0.039972, -0.036438, -0.033959, -0.033009, -0.038291, -0.036339, -0.022688, -0.024783
	-0.021354, -0.034103, -0.047541, -0.060551, -0.075691, -0.089373, -0.092241, -0.091621, -0.093203, -0.090723, -0.082480, -0.079781, -0.079706, -0.079674, -0.074365, -0.073780, -0.073465, -0.070165, -0.064970, -0.065503, -0.059104, -0.051038, -0.041817, -0.031243, -0.031386, -0.028837, -0.023658, -0.024237, -0.029641, -0.039210, -0.042766, -0.044461, -0.041863, -0.039075, -0.034881, -0.034571, -0.039386, -0.038253, -0.031659, -0.024202
	-0.027696, -0.041184, -0.054054, -0.064759, -0.080898, -0.094964, -0.097906, -0.098033, -0.101256, -0.098300, -0.091517, -0.088420, -0.086945, -0.085220, -0.079938, -0.079979, -0.079828, -0.074842, -0.072903, -0.072415, -0.065384, -0.057454, -0.048482, -0.040977, -0.039336, -0.036065, -0.032553, -0.034336, -0.039337, -0.046271, -0.049398, -0.051220, -0.049530, -0.045000, -0.045029, -0.042100, -0.049767, -0.046386, -0.035574, -0.032188
	-0.033426, -0.046259, -0.059363, -0.068024, -0.084858, -0.097009, -0.103434, -0.106215, -0.107319, -0.106178, -0.100333, -0.097536, -0.095352, -0.091322, -0.086332, -0.082309, -0.081440, -0.078413, -0.075067, -0.073134, -0.068255, -0.062667, -0.054300, -0.046004, -0.042001, -0.039181, -0.035010, -0.036092, -0.041599, -0.048788, -0.051751, -0.051179, -0.051019, -0.049121, -0.045860, -0.046756, -0.050005, -0.051613, -0.040237, -0.035349
	-0.037931, -0.051993, -0.066455, -0.075044, -0.088177, -0.102890, -0.108223, -0.112373, -0.115787, -0.113421, -0.108543, -0.105936, -0.101048, -0.096863, -0.090726, -0.087882, -0.086665, -0.083874, -0.081096, -0.080894, -0.075125, -0.071038, -0.063072, -0.054696, -0.051039, -0.046728, -0.042566, -0.043887, -0.048745, -0.056834, -0.059808, -0.060521, -0.060664, -0.057968, -0.056317, -0.052477, -0.058814, -0.055877, -0.046325, -0.042545
	-0.041429, -0.053634, -0.067633, -0.077111, -0.090998, -0.103561, -0.109445, -0.114741, -0.120075, -0.119821, -0.114703, -0.110411, -0.105589, -0.099826, -0.093730, -0.089705, -0.087199, -0.086439, -0.082688, -0.082221, -0.078348, -0.073203, -0.065273, -0.058731, -0.054025, -0.049231, -0.044830, -0.043830, -0.045839, -0.054137, -0.059075, -0.059515, -0.058546, -0.056956, -0.054145, -0.053129, -0.056587, -0.056341, -0.047057, -0.039936
	-0.044295, -0.058972, -0.072101, -0.082726, -0.095001, -0.106449, -0.111505, -0.118363, -0.124608, -0.123506, -0.120263, -0.115400, -0.110227, -0.104535, -0.100348, -0.095757, -0.092961, -0.092377, -0.089613, -0.088047, -0.084834, -0.079314, -0.072500, -0.064519, -0.060449, -0.055767, -0.051803, -0.050997, -0.052855, -0.058115, -0.063348, -0.065363, -0.067936, -0.063474, -0.061475, -0.054726, -0.062529, -0.055352, -0.048878, -0.044991
	-0.045804, -0.056574, -0.073308, -0.082450, -0.097495, -0.107467, -0.111501, -0.116418, -0.126724, -0.125980, -0.123231, -0.120494, -0.114667, -0.111289, -0.103451, -0.099228, -0.095880, -0.095882, -0.093328, -0.091000, -0.087051, -0.081909, -0.075949, -0.064971, -0.061050, -0.055137, -0.049046, -0.047319, -0.049806, -0.056968, -0.059608, -0.060249, -0.063032, -0.060556, -0.056284, -0.056263, -0.058891, -0.057890, -0.051554, -0.042382
	-0.049818, -0.062681, -0.076305, -0.084328, -0.098717, -0.107866, -0.113937, -0.120088, -0.128622, -0.128931, -0.126353, -0.123191, -0.118529, -0.115642, -0.106288, -0.103976, -0.099708, -0.097750, -0.094501, -0.094545, -0.090910, -0.085952, -0.077352, -0.067196, -0.062435, -0.057738, -0.052934, -0.051098, -0.055294, -0.061112, -0.063120, -0.067525, -0.067979, -0.066558, -0.064608, -0.060597, -0.067812, -0.057641, -0.056224, -0.046471
	-0.050591, -0.060432, -0.075602, -0.083877, -0.096933, -0.106147, -0.112334, -0.118295, -0.127966, -0.128757, -0.125157, -0.121831, -0.118557, -0.116124, -0.108723, -0.104502, -0.099469, -0.095841, -0.090662, -0.089822, -0.087969, -0.084545, -0.076375, -0.064821, -0.059093, -0.053427, -0.047372, -0.044341, -0.047964, -0.054064, -0.057133, -0.059152, -0.061568, -0.059109, -0.056640, -0.056691, -0.056844, -0.054564, -0.048514, -0.040641
	-0.047704, -0.059564, -0.073127, -0.080945, -0.093764, -0.105483, -0.111501, -0.118792, -0.124812, -0.126576, -0.122064, -0.118087, -0.116126, -0.114867, -0.108053, -0.103336, -0.097558, -0.093250, -0.086537, -0.085303, -0.083677, -0.079292, -0.070542, -0.062526, -0.056818, -0.052534, -0.044035, -0.041353, -0.046942, -0.051329, -0.055481, -0.062777, -0.058499, -0.058025, -0.057390, -0.053562, -0.060843, -0.046555, -0.046260, -0.036083
	-0.046496, -0.052983, -0.067518, -0.076904, -0.091704, -0.103105, -0.111995, -0.117751, -0.122307, -0.122941, -0.118230, -0.115004, -0.114258, -0.113138, -0.105515, -0.098417, -0.093384, -0.090070, -0.083281, -0.079846, -0.078725, -0.075452, -0.066225, -0.057269, -0.053103, -0.047808, -0.039772, -0.036834, -0.041270, -0.047376, -0.051111, -0.053848, -0.053029, -0.050301, -0.048919, -0.050775, -0.050121, -0.046842, -0.039633, -0.030497
	-0.040695, -0.051685, -0.064038, -0.070974, -0.086679, -0.101773, -0.109889, -0.114373, -0.117883, -0.118764, -0.113125, -0.110931, -0.111099, -0.109664, -0.098733, -0.093182, -0.090154, -0.086213, -0.077214, -0.077108, -0.075555, -0.069117, -0.060704, -0.054093, -0.049253, -0.044799, -0.037536, -0.035304, -0.040134, -0.045456, -0.051720, -0.056675, -0.053743, -0.052923, -0.049701, -0.050238, -0.056776, -0.041485, -0.041755, -0.027329
	-0.039842, -0.039428, -0.055732, -0.063890, -0.079179, -0.092823, -0.101698, -0.106156, -0.111709, -0.113152, -0.108033, -0.104872, -0.105645, -0.103501, -0.094487, -0.087264, -0.084273, -0.080950, -0.074116, -0.070973, -0.068409, -0.062825, -0.054757, -0.044150, -0.040620, -0.036602, -0.031538, -0.026478, -0.031123, -0.037600, -0.042341, -0.046700, -0.047380, -0.042880, -0.040967, -0.045367, -0.044192, -0.038553, -0.029948, -0.020790
	-0.030596, -0.038279, -0.051528, -0.058981, -0.073983, -0.089044, -0.099173, -0.101740, -0.104830, -0.107083, -0.102306, -0.101554, -0.101336, -0.097146, -0.089217, -0.083800, -0.080621, -0.078071, -0.071535, -0.068328, -0.065806, -0.056882, -0.048683, -0.039756, -0.036349, -0.031328, -0.025351, -0.024133, -0.029773, -0.033858, -0.040011, -0.044146, -0.043900, -0.044797, -0.038019, -0.042319, -0.047297, -0.031851, -0.034318, -0.013527
	-0.032121, -0.034722, -0.047839, -0.054710, -0.069175, -0.084213, -0.094533, -0.097233, -0.100863, -0.104775, -0.099781, -0.097416, -0.098804, -0.096059, -0.086694, -0.079692, -0.076749, -0.074609, -0.068106, -0.063906, -0.061136, -0.055447, -0.045559, -0.035389, -0.029696, -0.025708, -0.020034, -0.017335, -0.022665, -0.028532, -0.032369, -0.035760, -0.037212, -0.035201, -0.032872, -0.034132, -0.035907, -0.032127, -0.025026, -0.009282
	-0.026707, -0.034374, -0.045183, -0.052691, -0.067014, -0.084964, -0.092286, -0.094441, -0.099291, -0.103609, -0.098278, -0.094972, -0.097169, -0.095394, -0.086653, -0.080205, -0.076284, -0.070594, -0.064535, -0.062012, -0.060174, -0.051216, -0.040622, -0.033396, -0.029636, -0.024235, -0.017274, -0.018232, -0.021459, -0.024778, -0.031754, -0.034481, -0.033398, -0.037949, -0.030432, -0.033219, -0.038432, -0.021975, -0.030052, -0.009295
	-0.028559, -0.029280, -0.042071, -0.048655, -0.061603, -0.076257, -0.086817, -0.091815, -0.095682, -0.098682, -0.093729, -0.091168, -0.092213, -0.090073, -0.084070, -0.077048, -0.072045, -0.066267, -0.060309, -0.053639, -0.051696, -0.046852, -0.034069, -0.025602, -0.020640, -0.018021, -0.013180, -0.009049, -0.013846, -0.018012, -0.021061, -0.024515, -0.027068, -0.026804, -0.024283, -0.025595, -0.028234, -0.025272, -0.019246, -0.008595
	-0.025711, -0.029003, -0.038836, -0.048015, -0.058511, -0.074480, -0.083738, -0.087945, -0.091439, -0.094310, -0.090288, -0.087858, -0.088589, -0.086163, -0.081829, -0.075146, -0.071136, -0.064399, -0.057338, -0.052103, -0.049650, -0.043210, -0.032998, -0.023124, -0.020191, -0.016625, -0.012433, -0.010465, -0.009871, -0.015007, -0.021217, -0.021582, -0.023800, -0.027652, -0.021527, -0.027137, -0.030828, -0.020152, -0.026202, -0.008568
	-0.031287, -0.022523, -0.035800, -0.041583, -0.052691, -0.065901, -0.075941, -0.079246, -0.083936, -0.086778, -0.082235, -0.078893, -0.080642, -0.079419, -0.074324, -0.067418, -0.062113, -0.057744, -0.049923, -0.043390, -0.040055, -0.035512, -0.023838, -0.015485, -0.009895, -0.008346, -0.005387, 0.001467, -0.000104, -0.003777, -0.007926, -0.012023, -0.013970, -0.014207, -0.013994, -0.017009, -0.019233, -0.019282, -0.014210, -0.001146
	-0.020719, -0.024043, -0.035160, -0.041635, -0.051902, -0.063884, -0.072884, -0.076738, -0.081856, -0.083761, -0.077857, -0.074651, -0.077952, -0.076310, -0.069721, -0.063240, -0.056775, -0.055188, -0.046711, -0.042996, -0.039499, -0.032268, -0.023129, -0.015735, -0.012305, -0.009383, -0.005789, -0.001996, -0.001166, -0.005106, -0.009634, -0.009864, -0.011905, -0.015913, -0.010246, -0.016645, -0.022975, -0.011972, -0.018524, 0.001048
	-0.026050, -0.019774, -0.032555, -0.037813, -0.044657, -0.054435, -0.065271, -0.071019, -0.075585, -0.077479, -0.072635, -0.069526, -0.071046, -0.070770, -0.063085, -0.055960, -0.050956, -0.049593, -0.042773, -0.034996, -0.032645, -0.029030, -0.020343, -0.011008, -0.005751, -0.003252, 0.000746, 0.003215, 0.001749, -0.000068, -0.001413, -0.002608, -0.005837, -0.007103, -0.008431, -0.012027, -0.015656, -0.014417, -0.006321, 0.003748
	-0.021728, -0.019178, -0.031232, -0.036249, -0.042206, -0.053190, -0.064017, -0.068545, -0.074597, -0.074544, -0.069543, -0.065779, -0.067928, -0.067354, -0.060655, -0.052790, -0.047723, -0.046044, -0.038188, -0.034539, -0.032080, -0.027152, -0.018902, -0.012508, -0.009304, -0.003955, -0.000288, -0.001549, -0.000556, -0.003756, -0.008467, -0.003851, -0.005999, -0.012959, -0.007423, -0.015332, -0.017388, -0.005695, -0.010807, 0.007710
	-0.028204, -0.017096, -0.027984, -0.032129, -0.038374, -0.046561, -0.059356, -0.061847, -0.069228, -0.070551, -0.065474, -0.059719, -0.059893, -0.060271, -0.053666, -0.047202, -0.041189, -0.039979, -0.033189, -0.028761, -0.025714, -0.021660, -0.014905, -0.007841, -0.004669, -0.001174, 0.001874, 0.005613, 0.005527, 0.001504, -0.000694, 0.001892, 0.001885, -0.002506, -0.005619, -0.007166, -0.009935, -0.007406, 0.000545, 0.009983
	-0.019393, -0.017785, -0.025482, -0.028146, -0.036861, -0.047528, -0.055696, -0.059118, -0.064151, -0.066346, -0.060565, -0.055661, -0.055495, -0.051944, -0.048147, -0.040645, -0.036359, -0.035990, -0.026764, -0.024843, -0.023572, -0.019648, -0.013807, -0.006811, -0.004589, -0.000266, 0.003010, 0.004931, 0.006834, 0.003254, -0.001690, 0.003120, 0.001036, -0.005283, 0.000659, -0.007399, -0.010996, -0.000832, -0.006381, 0.012135
	-0.021519, -0.010062, -0.018662, -0.023011, -0.029067, -0.036961, -0.043194, -0.048197, -0.053632, -0.055489, -0.050054, -0.045247, -0.042655, -0.040243, -0.034315, -0.027094, -0.022697, -0.021644, -0.015333, -0.010768, -0.013712, -0.012051, -0.005326, 0.000560, 0.005300, 0.007429, 0.009930, 0.015968, 0.016454, 0.012383, 0.010385, 0.011612, 0.011413, 0.008357, 0.006831, 0.005524, 0.003087, 0.003507, 0.009876, 0.018892
	-0.017331, -0.015238, -0.021971, -0.024651, -0.029507, -0.040209, -0.044232, -0.046101, -0.052689, -0.053151, -0.047133, -0.042985, -0.040475, -0.037020, -0.029999, -0.021348, -0.018232, -0.017876, -0.013058, -0.008535, -0.013279, -0.011527, -0.006296, -0.001615, 0.002270, 0.006991, 0.010272, 0.013407, 0.015950, 0.012503, 0.008026, 0.013701, 0.011513, 0.004867, 0.010667, 0.006774, 0.003571, 0.012416, 0.004875, 0.020961
	-0.022637, -0.011107, -0.018340, -0.023896, -0.028320, -0.038092, -0.041212, -0.041642, -0.044537, -0.046015, -0.041699, -0.035805, -0.033527, -0.030911, -0.022925, -0.010175, -0.007279, -0.008644, -0.005065, -0.000597, -0.003797, -0.004052, 0.000635, 0.006175, 0.010857, 0.012993, 0.016956, 0.022765, 0.023298, 0.020262, 0.018285, 0.019467, 0.021161, 0.018785, 0.017891, 0.017817, 0.013874, 0.012825, 0.015904, 0.025844
	-0.014532, -0.010189, -0.019385, -0.022584, -0.028159, -0.037803, -0.040566, -0.038125, -0.040339, -0.038899, -0.033171, -0.028143, -0.025641, -0.019755, -0.012463, -0.003824, -0.000871, -0.002698, -0.000197, 0.001952, -0.001353, -0.000188, 0.004902, 0.012600, 0.014373, 0.016449, 0.018872, 0.022822, 0.026385, 0.020681, 0.015275, 0.021387, 0.023535, 0.016733, 0.022161, 0.018819, 0.011276, 0.020785, 0.014683, 0.032409
	-0.016972, -0.004835, -0.015539, -0.019706, -0.022971, -0.032222, -0.037732, -0.035551, -0.033892, -0.031679, -0.024624, -0.019946, -0.016412, -0.010040, -0.003445, 0.005991, 0.008364, 0.006410, 0.008289, 0.009260, 0.007409, 0.008691, 0.015230, 0.022729, 0.025465, 0.025502, 0.026102, 0.030309, 0.031861, 0.026963, 0.024651, 0.027000, 0.029039, 0.025577, 0.027217, 0.027660, 0.023245, 0.021705, 0.026383, 0.034120
	-0.007042, -0.003943, -0.013314, -0.016082, -0.020497, -0.030911, -0.035096, -0.030889, -0.029351, -0.025337, -0.018980, -0.012449, -0.008879, -0.001902, 0.003577, 0.011256, 0.012460, 0.010502, 0.011904, 0.011483, 0.010067, 0.013356, 0.020792, 0.027368, 0.026382, 0.028554, 0.028164, 0.029993, 0.033232, 0.028830, 0.022354, 0.027991, 0.029607, 0.020011, 0.031066, 0.031755, 0.025061, 0.037228, 0.024607, 0.041453
	-0.012463, -0.000987, -0.008994, -0.014815, -0.017487, -0.026372, -0.031392, -0.028459, -0.025402, -0.024153, -0.015566, -0.007862, -0.004579, 0.001484, 0.010757, 0.017401, 0.019536, 0.016264, 0.016278, 0.018231, 0.018193, 0.018217, 0.025442, 0.034794, 0.036179, 0.034770, 0.033985, 0.040104, 0.040404, 0.034161, 0.030977, 0.032380, 0.034144, 0.031909, 0.033231, 0.035957, 0.034171, 0.033050, 0.038776, 0.042972
	-0.002758, 0.000700, -0.008467, -0.011525, -0.018705, -0.027522, -0.031609, -0.027494, -0.026315, -0.023221, -0.014164, -0.006562, -0.002205, 0.006453, 0.013689, 0.018647, 0.017673, 0.016751, 0.017380, 0.018782, 0.019038, 0.021992, 0.027475, 0.034748, 0.036870, 0.036635, 0.035394, 0.037519, 0.038008, 0.032063, 0.025834, 0.030409, 0.033142, 0.023991, 0.034882, 0.034323, 0.030317, 0.042711, 0.030793, 0.045129
	-0.011501, 0.004979, -0.003199, -0.009532, -0.013737, -0.022490, -0.028056, -0.025047, -0.023987, -0.021727, -0.011113, -0.003633, 0.003070, 0.010580, 0.020230, 0.025058, 0.026653, 0.024592, 0.024567, 0.025613, 0.027386, 0.029282, 0.037705, 0.042901, 0.046601, 0.045443, 0.044217, 0.048155, 0.045715, 0.039788, 0.034981, 0.038594, 0.038594, 0.034532, 0.038671, 0.042065, 0.040659, 0.042101, 0.045919, 0.050030
	-0.005239, 0.006624, -0.001837, -0.005350, -0.012024, -0.022230, -0.026144, -0.022704, -0.021559, -0.017450, -0.008515, 0.000433, 0.007392, 0.014546, 0.023538, 0.029043, 0.029892, 0.027280, 0.028785, 0.030662, 0.032758, 0.032649, 0.040035, 0.046372, 0.048654, 0.050330, 0.049538, 0.049746, 0.048851, 0.041068, 0.034598, 0.041375, 0.041379, 0.030621, 0.043091, 0.044712, 0.038634, 0.053475, 0.042814, 0.059369
	-0.011843, 0.005417, 0.000007, -0.005709, -0.011391, -0.019100, -0.024151, -0.021274, -0.019356, -0.016953, -0.004422, 0.002891, 0.010688, 0.018353, 0.027665, 0.035281, 0.036655, 0.034937, 0.036795, 0.039994, 0.042705, 0.042668, 0.048600, 0.055673, 0.059602, 0.061002, 0.059934, 0.064283, 0.061835, 0.052838, 0.048644, 0.048401, 0.048158, 0.044262, 0.049173, 0.053313, 0.050054, 0.051718, 0.058112, 0.062677
	-0.003249, 0.007140, -0.000190, -0.005182, -0.010664, -0.017472, -0.021072, -0.018928, -0.015929, -0.011810, -0.001170, 0.006999, 0.014346, 0.022026, 0.033087, 0.037703, 0.039304, 0.038986, 0.040531, 0.042739, 0.044912, 0.045850, 0.052980, 0.060894, 0.062495, 0.065477, 0.066306, 0.069035, 0.066301, 0.058359, 0.048879, 0.054660, 0.053906, 0.042834, 0.051292, 0.054304, 0.049390, 0.064968, 0.053062, 0.067337
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 80.0
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Peperations]
version = 1
points = 
	0.022498, 0.020830, 0.014175, -0.000111, -0.007965, -0.011932, -0.009252, -0.003320, -0.000118, 0.004151, 0.015991, 0.024593, 0.030148, 0.034696, 0.042241, 0.043592, 0.045307, 0.051419, 0.057700, 0.066468, 0.072764, 0.085492, 0.100446, 0.113063, 0.118900, 0.122870, 0.130290, 0.129755, 0.129462, 0.124089, 0.122420, 0.123461, 0.116841, 0.117893, 0.119241, 0.115227, 0.110631, 0.109920, 0.117187, 0.124332
	0.004953, 0.000716, -0.005511, -0.010742, -0.018400, -0.024021, -0.019665, -0.013525, -0.009878, -0.004126, 0.008939, 0.016408, 0.019292, 0.023840, 0.033007, 0.033600, 0.034448, 0.041047, 0.049029, 0.052882, 0.062512, 0.072410, 0.089182, 0.103027, 0.106205, 0.110789, 0.117912, 0.115269, 0.112784, 0.106051, 0.103603, 0.104209, 0.099603, 0.105100, 0.101466, 0.099610, 0.095780, 0.096420, 0.108661, 0.108286
	-0.007933, -0.002801, -0.011350, -0.022484, -0.029473, -0.033231, -0.030354, -0.021826, -0.018408, -0.013209, 0.001640, 0.008984, 0.012027, 0.014149, 0.024334, 0.028649, 0.030597, 0.034667, 0.041223, 0.046241, 0.051968, 0.062511, 0.079099, 0.090699, 0.097837, 0.101667, 0.108218, 0.106595, 0.104490, 0.095444, 0.089512, 0.089259, 0.089179, 0.091741, 0.094161, 0.094254, 0.091002, 0.088753, 0.095405, 0.102343
	-0.010759, -0.012564, -0.018170, -0.023960, -0.033106, -0.040910, -0.038354, -0.031441, -0.026122, -0.019953, -0.006267, 0.000733, 0.002678, 0.006102, 0.015437, 0.019860, 0.022689, 0.029563, 0.035629, 0.037302, 0.045089, 0.055137, 0.070820, 0.082978, 0.087158, 0.088614, 0.094487, 0.093851, 0.091038, 0.080923, 0.074433, 0.073797, 0.073058, 0.081788, 0.080734, 0.083111, 0.078149, 0.079373, 0.091335, 0.087853
	-0.027313, -0.019238, -0.027920, -0.036645, -0.043223, -0.049872, -0.048503, -0.043853, -0.040737, -0.035179, -0.021622, -0.013493, -0.010171, -0.007317, 0.001347, 0.007440, 0.011360, 0.015985, 0.023916, 0.026329, 0.031680, 0.042865, 0.056754, 0.067621, 0.072919, 0.075964, 0.080156, 0.081233, 0.077771, 0.068443, 0.063939, 0.062251, 0.063828, 0.065094, 0.069498, 0.071735, 0.067423, 0.064065, 0.069162, 0.076272
	-0.033298, -0.035618, -0.039940, -0.043358, -0.050731, -0.061413, -0.060545, -0.055944, -0.052261, -0.045471, -0.035624, -0.027633, -0.021472, -0.017300, -0.006949, -0.002776, -0.000154, 0.006413, 0.012882, 0.014721, 0.023411, 0.031711, 0.040565, 0.054702, 0.058761, 0.061734, 0.065369, 0.066037, 0.061059, 0.053849, 0.049600, 0.048373, 0.049189, 0.054631, 0.050470, 0.056349, 0.047074, 0.049651, 0.057444, 0.057485
	-0.046284, -0.039039, -0.049010, -0.054961, -0.061001, -0.068408, -0.069602, -0.066474, -0.063117, -0.059357, -0.049570, -0.041166, -0.035441, -0.029269, -0.019658, -0.012395, -0.008906, -0.005538, 0.002012, 0.008339, 0.013216, 0.018793, 0.031185, 0.040165, 0.047175, 0.050605, 0.054283, 0.054442, 0.049166, 0.043483, 0.039000, 0.040758, 0.040857, 0.040759, 0.042263, 0.043438, 0.040051, 0.035886, 0.041332, 0.048851
	-0.049893, -0.051919, -0.058103, -0.060142, -0.067656, -0.077159, -0.079195, -0.078019, -0.075421, -0.069471, -0.060409, -0.054194, -0.044226, -0.037275, -0.027912, -0.020020, -0.016789, -0.012491, -0.003457, 0.001129, 0.004540, 0.009435, 0.018232, 0.027941, 0.035138, 0.038227, 0.042656, 0.044103, 0.038517, 0.032121, 0.029666, 0.027319, 0.029774, 0.031572, 0.028887, 0.034828, 0.023795, 0.030023, 0.033606, 0.036047
	-0.061015, -0.055279, -0.067497, -0.072234, -0.078637, -0.083600, -0.085954, -0.087271, -0.088647, -0.083447, -0.073398, -0.065920, -0.058009, -0.048810, -0.040714, -0.032533, -0.027328, -0.020402, -0.011382, -0.006547, -0.005452, -0.002712, 0.004649, 0.014201, 0.021442, 0.025510, 0.032890, 0.034711, 0.030965, 0.026329, 0.018828, 0.019246, 0.018861, 0.019611, 0.020596, 0.021396, 0.020172, 0.015723, 0.020537, 0.029677
	-0.063777, -0.066149, -0.073750, -0.076131, -0.084016, -0.091900, -0.093741, -0.094496, -0.094840, -0.089548, -0.084332, -0.077263, -0.068485, -0.061963, -0.051082, -0.043658, -0.037912, -0.032323, -0.024324, -0.019914, -0.018261, -0.013727, -0.003485, 0.004316, 0.011418, 0.017023, 0.022980, 0.024505, 0.018896, 0.014000, 0.009498, 0.006074, 0.009480, 0.007611, 0.008958, 0.010086, -0.000341, 0.010423, 0.010467, 0.016794
	-0.072341, -0.064233, -0.079217, -0.084483, -0.091050, -0.094481, -0.095378, -0.096667, -0.100564, -0.098313, -0.093254, -0.086700, -0.079209, -0.071795, -0.061313, -0.051911, -0.046317, -0.042643, -0.037228, -0.031598, -0.027431, -0.020480, -0.012883, -0.003114, 0.004746, 0.010189, 0.015911, 0.017106, 0.014037, 0.008693, 0.005120, 0.003652, -0.000532, -0.001097, 0.001984, 0.000397, -0.002089, -0.002821, 0.000529, 0.009043
	-0.068927, -0.075835, -0.083530, -0.085213, -0.091299, -0.100015, -0.101020, -0.100921, -0.103349, -0.102493, -0.098069, -0.091292, -0.083452, -0.079672, -0.069612, -0.062472, -0.055862, -0.052233, -0.046746, -0.041991, -0.035219, -0.028225, -0.018698, -0.007309, -0.002458, 0.002051, 0.006595, 0.008468, 0.005218, -0.000205, -0.003131, -0.003647, -0.006151, -0.009154, -0.005539, -0.006971, -0.015297, -0.002874, -0.005242, 0.003706
	-0.070116, -0.067835, -0.086390, -0.089881, -0.095167, -0.099194, -0.100751, -0.103794, -0.106996, -0.105835, -0.098564, -0.092154, -0.085579, -0.083053, -0.074722, -0.066442, -0.059302, -0.053429, -0.047800, -0.042952, -0.039132, -0.034614, -0.025732, -0.012689, -0.005906, 0.001101, 0.006644, 0.010980, 0.007742, 0.002526, -0.000261, -0.004094, -0.008771, -0.008465, -0.007095, -0.008952, -0.010405, -0.010446, -0.006121, 0.002024
	-0.064366, -0.071780, -0.082938, -0.085702, -0.093522, -0.099237, -0.104020, -0.105939, -0.106226, -0.104298, -0.097541, -0.091253, -0.084969, -0.082450, -0.075561, -0.066547, -0.056511, -0.051248, -0.041287, -0.037794, -0.035633, -0.028059, -0.019518, -0.010556, -0.003388, 0.002054, 0.009492, 0.011478, 0.008555, 0.004735, -0.000781, -0.006427, -0.005697, -0.010270, -0.006112, -0.011704, -0.018717, -0.002750, -0.010971, 0.000116
	-0.076795, -0.064801, -0.080209, -0.085175, -0.093457, -0.101077, -0.104981, -0.106367, -0.106821, -0.105708, -0.098545, -0.090759, -0.086929, -0.083491, -0.074306, -0.064805, -0.055933, -0.049959, -0.042853, -0.036270, -0.034463, -0.029587, -0.018780, -0.010103, -0.003533, 0.001632, 0.007909, 0.014370, 0.009281, 0.004666, -0.002974, -0.007301, -0.010185, -0.008299, -0.006340, -0.009678, -0.011333, -0.010684, -0.006289, 0.002763
	-0.067470, -0.065770, -0.074038, -0.076420, -0.085702, -0.098704, -0.101940, -0.102629, -0.101903, -0.100342, -0.093820, -0.086941, -0.083804, -0.081020, -0.067700, -0.059395, -0.054055, -0.047911, -0.039687, -0.035672, -0.032029, -0.025979, -0.017057, -0.006973, -0.001656, 0.002001, 0.007249, 0.012112, 0.006541, 0.000572, -0.006284, -0.010415, -0.012279, -0.015087, -0.007848, -0.016491, -0.019704, -0.005357, -0.013151, 0.002966
	-0.074820, -0.054794, -0.069710, -0.075127, -0.082743, -0.091434, -0.095621, -0.097541, -0.099098, -0.097422, -0.089851, -0.083594, -0.081112, -0.078942, -0.066391, -0.057457, -0.050942, -0.048077, -0.041211, -0.034391, -0.030091, -0.026047, -0.014207, -0.005090, 0.000912, 0.005316, 0.010043, 0.015509, 0.011199, 0.004513, -0.001027, -0.006694, -0.011239, -0.011162, -0.009134, -0.013596, -0.014031, -0.011306, -0.007627, 0.001767
	-0.061695, -0.056074, -0.065188, -0.067950, -0.076218, -0.088303, -0.093436, -0.092999, -0.090937, -0.090555, -0.084407, -0.080354, -0.078692, -0.074308, -0.062767, -0.052729, -0.047475, -0.043949, -0.036669, -0.031720, -0.027940, -0.020058, -0.010125, -0.000940, 0.003512, 0.007720, 0.011869, 0.015296, 0.011180, 0.003886, -0.003309, -0.003380, -0.007926, -0.011633, -0.003540, -0.014182, -0.013975, -0.003720, -0.011797, 0.006338
	-0.070864, -0.046187, -0.061128, -0.065717, -0.072715, -0.083470, -0.088292, -0.087558, -0.087628, -0.089378, -0.083768, -0.077237, -0.077063, -0.071978, -0.061635, -0.052022, -0.046913, -0.041194, -0.034314, -0.028661, -0.027048, -0.021438, -0.009769, -0.001205, 0.004637, 0.008928, 0.013264, 0.017277, 0.013442, 0.007295, 0.003623, -0.002524, -0.004256, -0.005789, -0.004213, -0.007305, -0.010487, -0.010885, -0.006086, 0.007386
	-0.059345, -0.049207, -0.056858, -0.060052, -0.066579, -0.080604, -0.086910, -0.085647, -0.085267, -0.087618, -0.081260, -0.075368, -0.073937, -0.069758, -0.058235, -0.051634, -0.045288, -0.038732, -0.032262, -0.027928, -0.024928, -0.019266, -0.007996, 0.000923, 0.005834, 0.008336, 0.013557, 0.017068, 0.012350, 0.006475, 0.000982, 0.001103, -0.006223, -0.006853, -0.000966, -0.013148, -0.013975, -0.006310, -0.011605, 0.006165
	-0.066591, -0.039715, -0.053663, -0.059514, -0.065911, -0.075018, -0.080214, -0.082968, -0.083447, -0.085380, -0.079055, -0.071985, -0.070247, -0.065856, -0.057767, -0.049975, -0.044481, -0.039103, -0.031217, -0.024927, -0.020997, -0.016440, -0.004831, 0.004061, 0.009463, 0.011160, 0.014777, 0.020638, 0.017816, 0.011360, 0.006171, 0.002164, -0.002119, -0.003117, -0.003031, -0.005156, -0.011400, -0.011762, -0.009295, -0.000001
	-0.060314, -0.046160, -0.052794, -0.054967, -0.062049, -0.074106, -0.080446, -0.081200, -0.080809, -0.080477, -0.076170, -0.070932, -0.069101, -0.063634, -0.055720, -0.049501, -0.044939, -0.040131, -0.032438, -0.022882, -0.017627, -0.012524, -0.001324, 0.006685, 0.011868, 0.013658, 0.016095, 0.021837, 0.020158, 0.012528, 0.006089, 0.005453, -0.000976, -0.002140, 0.001104, -0.010111, -0.010612, -0.007452, -0.014357, 0.001011
	-0.075633, -0.036609, -0.049346, -0.055490, -0.059336, -0.067616, -0.073859, -0.075613, -0.076372, -0.078009, -0.070627, -0.064206, -0.064430, -0.061999, -0.054551, -0.047386, -0.040817, -0.037398, -0.028062, -0.018505, -0.012195, -0.007531, 0.001481, 0.011790, 0.019955, 0.022349, 0.022131, 0.024492, 0.023359, 0.019186, 0.014655, 0.008357, 0.004176, 0.002971, 0.002955, -0.000237, -0.005884, -0.010152, -0.009506, 0.002811
	-0.059008, -0.039658, -0.046978, -0.048324, -0.052285, -0.063338, -0.069082, -0.070556, -0.070625, -0.070049, -0.064460, -0.057403, -0.056723, -0.052882, -0.046968, -0.041507, -0.033211, -0.029974, -0.022900, -0.013579, -0.008803, -0.004962, 0.005653, 0.017026, 0.028171, 0.028651, 0.024731, 0.026850, 0.023371, 0.017073, 0.015171, 0.016616, 0.005521, 0.005756, 0.007586, -0.005103, -0.006856, -0.005604, -0.006599, 0.007528
	-0.068330, -0.030233, -0.043154, -0.047439, -0.047149, -0.051149, -0.060971, -0.063014, -0.065775, -0.064636, -0.058200, -0.050987, -0.050925, -0.050115, -0.041299, -0.033907, -0.026306, -0.024199, -0.017123, -0.009196, -0.006314, -0.003809, 0.004760, 0.015324, 0.026665, 0.029649, 0.028724, 0.027131, 0.025150, 0.021808, 0.019981, 0.016766, 0.012347, 0.008776, 0.005760, -0.000224, -0.004294, -0.005879, -0.002457, 0.010054
	-0.053519, -0.031388, -0.038255, -0.037590, -0.039245, -0.046335, -0.056314, -0.057830, -0.060291, -0.058967, -0.051413, -0.045449, -0.043947, -0.042018, -0.034113, -0.025887, -0.019539, -0.017727, -0.012711, -0.005860, -0.003102, 0.000774, 0.009438, 0.015884, 0.022961, 0.024229, 0.026012, 0.029407, 0.026717, 0.020406, 0.017796, 0.020289, 0.012243, 0.009711, 0.009234, -0.005990, -0.001013, 0.000740, -0.002144, 0.013012
	-0.068972, -0.023416, -0.032912, -0.036134, -0.035915, -0.040435, -0.047452, -0.051460, -0.055021, -0.055776, -0.048697, -0.039554, -0.036785, -0.035561, -0.029056, -0.021075, -0.013416, -0.012134, -0.007237, -0.000622, 0.001662, 0.005393, 0.012038, 0.019764, 0.023514, 0.026252, 0.028191, 0.031400, 0.031365, 0.027993, 0.023275, 0.021009, 0.018930, 0.014093, 0.009022, 0.004773, 0.002094, 0.001348, 0.005643, 0.015078
	-0.050527, -0.022437, -0.028090, -0.026206, -0.028387, -0.036911, -0.041310, -0.044227, -0.046970, -0.046769, -0.038081, -0.031386, -0.029516, -0.024050, -0.019435, -0.012381, -0.005732, -0.004173, 0.000911, 0.006849, 0.007360, 0.010699, 0.017436, 0.023369, 0.028527, 0.029640, 0.031002, 0.034727, 0.036582, 0.030763, 0.026015, 0.028623, 0.020834, 0.016185, 0.016933, 0.002829, 0.004984, 0.009818, 0.008874, 0.020032
	-0.067395, -0.010220, -0.021024, -0.024567, -0.024087, -0.029620, -0.032317, -0.034341, -0.038392, -0.038789, -0.030285, -0.021590, -0.017175, -0.014435, -0.007732, -0.000529, 0.005605, 0.007078, 0.012454, 0.017758, 0.016774, 0.015574, 0.020748, 0.028369, 0.033644, 0.034771, 0.036537, 0.040293, 0.042118, 0.039979, 0.035655, 0.033354, 0.030928, 0.024890, 0.021491, 0.018938, 0.013668, 0.012501, 0.017108, 0.023515
	-0.038833, -0.012802, -0.018564, -0.017459, -0.019062, -0.027068, -0.030119, -0.028336, -0.029665, -0.030695, -0.022239, -0.013522, -0.008358, -0.004785, 0.000463, 0.010662, 0.015564, 0.016950, 0.020281, 0.025300, 0.022680, 0.022717, 0.026679, 0.031617, 0.035801, 0.037098, 0.041294, 0.045640, 0.047879, 0.042000, 0.038044, 0.040629, 0.033892, 0.031247, 0.031584, 0.018500, 0.020116, 0.019823, 0.016638, 0.029979
	-0.054356, -0.002258, -0.012712, -0.017288, -0.016713, -0.022907, -0.024293, -0.021563, -0.022620, -0.021953, -0.015330, -0.005386, -0.000764, 0.002640, 0.009997, 0.022869, 0.028174, 0.027730, 0.030977, 0.035707, 0.032818, 0.030889, 0.033638, 0.038561, 0.044265, 0.045141, 0.047683, 0.051815, 0.054004, 0.050991, 0.045574, 0.043899, 0.044055, 0.039092, 0.035909, 0.032091, 0.026891, 0.022169, 0.024865, 0.030848
	-0.031827, -0.000102, -0.006368, -0.006487, -0.006247, -0.014001, -0.017110, -0.013043, -0.010851, -0.008764, -0.000213, 0.006477, 0.011144, 0.018309, 0.024745, 0.033643, 0.038648, 0.039249, 0.041148, 0.045266, 0.041693, 0.040999, 0.045484, 0.052613, 0.057066, 0.054753, 0.055112, 0.059287, 0.060203, 0.052465, 0.047993, 0.050999, 0.047464, 0.046460, 0.044507, 0.031433, 0.032267, 0.032025, 0.029852, 0.040329
	-0.053848, 0.008122, -0.005187, -0.009032, -0.006543, -0.010012, -0.013005, -0.011663, -0.008957, -0.004668, 0.005458, 0.012800, 0.016893, 0.023554, 0.031737, 0.038741, 0.043870, 0.043337, 0.046621, 0.047581, 0.045654, 0.044827, 0.050363, 0.058747, 0.061023, 0.060485, 0.059059, 0.061821, 0.061391, 0.055971, 0.051067, 0.050038, 0.051018, 0.046533, 0.043334, 0.042562, 0.036118, 0.029798, 0.032773, 0.039524
	-0.025830, 0.006164, -0.000655, 0.000164, 0.000088, -0.008033, -0.011008, -0.006017, -0.001301, 0.004088, 0.011848, 0.020276, 0.024465, 0.033383, 0.039126, 0.044268, 0.047916, 0.047402, 0.050050, 0.050456, 0.048891, 0.051771, 0.058154, 0.063246, 0.065463, 0.063072, 0.060950, 0.065351, 0.064614, 0.057455, 0.051194, 0.055723, 0.050906, 0.046407, 0.048283, 0.036561, 0.037400, 0.036887, 0.031589, 0.046759
	-0.041184, 0.017683, 0.006408, 0.000358, 0.001923, -0.002498, -0.003907, -0.001746, 0.001864, 0.006784, 0.017297, 0.026916, 0.030940, 0.036439, 0.045987, 0.050809, 0.054636, 0.052055, 0.053180, 0.056698, 0.057069, 0.055779, 0.063193, 0.067815, 0.071856, 0.070651, 0.067674, 0.070718, 0.070797, 0.062598, 0.057842, 0.056835, 0.056713, 0.051260, 0.048727, 0.048227, 0.044844, 0.039559, 0.041218, 0.044920
	-0.014008, 0.018619, 0.011274, 0.010878, 0.008771, 0.001246, -0.001819, 0.003600, 0.008052, 0.011983, 0.021970, 0.030757, 0.037662, 0.045972, 0.053195, 0.057661, 0.059206, 0.058383, 0.060240, 0.061039, 0.062504, 0.064497, 0.070278, 0.077704, 0.080246, 0.077015, 0.072985, 0.075685, 0.072584, 0.063534, 0.057732, 0.061938, 0.057545, 0.050931, 0.054863, 0.045820, 0.048882, 0.049675, 0.043484, 0.051538
	-0.045038, 0.028947, 0.019821, 0.012917, 0.013648, 0.007951, 0.005122, 0.007823, 0.012411, 0.015320, 0.025036, 0.036734, 0.045314, 0.052208, 0.062220, 0.065610, 0.068489, 0.066665, 0.068454, 0.069025, 0.071080, 0.073373, 0.079623, 0.085651, 0.088907, 0.088954, 0.084254, 0.084464, 0.080300, 0.072471, 0.067316, 0.066430, 0.065143, 0.057630, 0.058650, 0.059627, 0.057197, 0.054105, 0.055295, 0.057879
	-0.017117, 0.027364, 0.023067, 0.022758, 0.019246, 0.011825, 0.007962, 0.011522, 0.017237, 0.021779, 0.031329, 0.042642, 0.052349, 0.060322, 0.069568, 0.074657, 0.075211, 0.072882, 0.075373, 0.078391, 0.079512, 0.081816, 0.086101, 0.091730, 0.095061, 0.095682, 0.092100, 0.092873, 0.085769, 0.077219, 0.068392, 0.073179, 0.069972, 0.061240, 0.068306, 0.062227, 0.061008, 0.064520, 0.058543, 0.070728
	-0.042759, 0.035472, 0.029514, 0.023812, 0.024176, 0.020576, 0.017397, 0.018716, 0.022981, 0.027634, 0.041262, 0.050991, 0.058558, 0.067060, 0.077829, 0.083609, 0.084719, 0.082815, 0.085352, 0.087363, 0.091238, 0.091692, 0.096562, 0.102513, 0.106436, 0.108184, 0.105828, 0.107257, 0.102415, 0.090768, 0.084257, 0.081410, 0.081286, 0.073523, 0.074433, 0.076576, 0.070376, 0.068350, 0.071896, 0.072962
	-0.003143, 0.035517, 0.033266, 0.032727, 0.031843, 0.025862, 0.023177, 0.026936, 0.032953, 0.037457, 0.049289, 0.057429, 0.066625, 0.072540, 0.083814, 0.089321, 0.092420, 0.093053, 0.094752, 0.096876, 0.098364, 0.101271, 0.105185, 0.113505, 0.115784, 0.118957, 0.117138, 0.117934, 0.110930, 0.101497, 0.091051, 0.092731, 0.090574, 0.079282, 0.084691, 0.078426, 0.073451, 0.081698, 0.072811, 0.084352
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 19.8
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity
=======================
Extruder max_extrude_ratio=0.266081
Extruder max_extrude_ratio=0.266081
mcu 'mcu': Starting serial connect
webhooks client 3978002616: New connection
webhooks client 3978002616: Client info {'program': 'Moonraker', 'version': 'v0.9.3-0-g71f9e67'}
Loaded MCU 'mcu' 118 commands (v0.12.0-402-g2817b348 / gcc: (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027] binutils: (2.34-4+rpi1+14) 2.34)
MCU 'mcu' config: ADC_MAX=4095 BUS_PINS_i2c1_PB6_PB7=PB6,PB7 BUS_PINS_i2c1_PB8_PB9=PB8,PB9 BUS_PINS_i2c2_PB10_PB11=PB10,PB11 BUS_PINS_i2c3_PA8_PC9=PA8,PC9 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi2a=PC2,PC3,PB10 BUS_PINS_spi3a=PC11,PC12,PC10 BUS_PINS_spi4=PE13,PE14,PE12 BUS_PINS_spi5=PF8,PF9,PF7 BUS_PINS_spi5a=PH7,PF11,PH6 BUS_PINS_spi6=PG12,PG14,PG13 CLOCK_FREQ=400000000 MCU=stm32h723xx PWM_MAX=255 RESERVE_PINS_USB=PA11,PA12 RESERVE_PINS_crystal=PH0,PH1 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
mcu 'rpi': Starting connect
Loaded MCU 'rpi' 119 commands (?-20240727_132503-fv-az659-741 / gcc: (Raspbian 10.2.1-6+rpi1) 10.2.1 20210110 binutils: (GNU Binutils for Raspbian) 2.35.2)
MCU 'rpi' config: ADC_MAX=4095 CLOCK_FREQ=50000000 MCU=linux PCA9685_MAX=4096 PWM_MAX=32768 STATS_SUMSQ_BASE=256
mcu 'toolboard_t0': Starting serial connect
Loaded MCU 'toolboard_t0' 118 commands (v0.12.0-402-g2817b348 / gcc: (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027] binutils: (2.34-4+rpi1+14) 2.34)
MCU 'toolboard_t0' config: ADC_MAX=4095 BUS_PINS_i2c1_PA9_PA10=PA9,PA10 BUS_PINS_i2c1_PB6_PB7=PB6,PB7 BUS_PINS_i2c1_PB8_PB9=PB8,PB9 BUS_PINS_i2c2_PB10_PB11=PB10,PB11 BUS_PINS_i2c2_PB13_PB14=PB13,PB14 BUS_PINS_i2c3_PB3_PB4=PB3,PB4 BUS_PINS_i2c3_PC0_PC1=PC0,PC1 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi2_PB2_PB11_PB10=PB2,PB11,PB10 BUS_PINS_spi2a=PC2,PC3,PB10 BUS_PINS_spi3=PB4,PB5,PB3 CLOCK_FREQ=64000000 MCU=stm32g0b1xx PWM_MAX=255 RESERVE_PINS_USB=PA11,PA12 RESERVE_PINS_crystal=PF0,PF1 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
mcu 'toolboard_t1': Starting serial connect
Loaded MCU 'toolboard_t1' 118 commands (v0.12.0-402-g2817b348 / gcc: (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027] binutils: (2.34-4+rpi1+14) 2.34)
MCU 'toolboard_t1' config: ADC_MAX=4095 BUS_PINS_i2c1_PA9_PA10=PA9,PA10 BUS_PINS_i2c1_PB6_PB7=PB6,PB7 BUS_PINS_i2c1_PB8_PB9=PB8,PB9 BUS_PINS_i2c2_PB10_PB11=PB10,PB11 BUS_PINS_i2c2_PB13_PB14=PB13,PB14 BUS_PINS_i2c3_PB3_PB4=PB3,PB4 BUS_PINS_i2c3_PC0_PC1=PC0,PC1 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi2_PB2_PB11_PB10=PB2,PB11,PB10 BUS_PINS_spi2a=PC2,PC3,PB10 BUS_PINS_spi3=PB4,PB5,PB3 CLOCK_FREQ=64000000 MCU=stm32g0b1xx PWM_MAX=255 RESERVE_PINS_USB=PA11,PA12 RESERVE_PINS_crystal=PF0,PF1 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
mcu 'dinghy': Starting serial connect
Loaded MCU 'dinghy' 118 commands (v0.12.0-402-g2817b348 / gcc: (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027] binutils: (2.34-4+rpi1+14) 2.34)
MCU 'dinghy' config: ADC_MAX=4095 BUS_PINS_i2c1=PB6,PB7 BUS_PINS_i2c1_PB6_PB7=PB6,PB7 BUS_PINS_i2c1_PB8_PB7=PB8,PB7 BUS_PINS_i2c1_PB8_PB9=PB8,PB9 BUS_PINS_i2c1_PF1_PF0=PF1,PF0 BUS_PINS_i2c1a=PF1,PF0 BUS_PINS_spi1=PA6,PA7,PA5 BUS_PINS_spi1a=PB4,PB5,PB3 BUS_PINS_spi2=PB14,PB15,PB13 BUS_PINS_spi2a=PC2,PC3,PB10 CLOCK_FREQ=48000000 MCU=stm32f072xb PWM_MAX=255 RESERVE_PINS_USB=PA11,PA12 RESERVE_PINS_crystal=PF0,PF1 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
mcu 'plasma': Starting serial connect
Loaded MCU 'plasma' 118 commands (v0.12.0-402-g2817b348 / gcc: (15:8-2019-q3-1+b1) 8.3.1 20190703 (release) [gcc-8-branch revision 273027] binutils: (2.34-4+rpi1+14) 2.34)
MCU 'plasma' config: ADC_MAX=4095 BUS_PINS_i2c0a=gpio0,gpio1 BUS_PINS_i2c0b=gpio4,gpio5 BUS_PINS_i2c0c=gpio8,gpio9 BUS_PINS_i2c0d=gpio12,gpio13 BUS_PINS_i2c0e=gpio16,gpio17 BUS_PINS_i2c0f=gpio20,gpio21 BUS_PINS_i2c0g=gpio24,gpio25 BUS_PINS_i2c0h=gpio28,gpio29 BUS_PINS_i2c1a=gpio2,gpio3 BUS_PINS_i2c1b=gpio6,gpio7 BUS_PINS_i2c1c=gpio10,gpio11 BUS_PINS_i2c1d=gpio14,gpio15 BUS_PINS_i2c1e=gpio18,gpio19 BUS_PINS_i2c1f=gpio22,gpio23 BUS_PINS_i2c1g=gpio26,gpio27 BUS_PINS_spi0_gpio0_gpio3_gpio2=gpio0,gpio3,gpio2 BUS_PINS_spi0_gpio16_gpio19_gpio18=gpio16,gpio19,gpio18 BUS_PINS_spi0_gpio20_gpio23_gpio22=gpio20,gpio23,gpio22 BUS_PINS_spi0_gpio4_gpio3_gpio2=gpio4,gpio3,gpio2 BUS_PINS_spi0_gpio4_gpio7_gpio6=gpio4,gpio7,gpio6 BUS_PINS_spi0a=gpio0,gpio3,gpio2 BUS_PINS_spi0b=gpio4,gpio7,gpio6 BUS_PINS_spi0c=gpio16,gpio19,gpio18 BUS_PINS_spi0d=gpio20,gpio23,gpio22 BUS_PINS_spi1_gpio12_gpio15_gpio14=gpio12,gpio15,gpio14 BUS_PINS_spi1_gpio24_gpio27_gpio26=gpio24,gpio27,gpio26 BUS_PINS_spi1_gpio8_gpio11_gpio10=gpio8,gpio11,gpio10 BUS_PINS_spi1a=gpio8,gpio11,gpio10 BUS_PINS_spi1b=gpio12,gpio15,gpio14 BUS_PINS_spi1c=gpio24,gpio27,gpio26 CLOCK_FREQ=12000000 MCU=rp2040 PWM_MAX=255 STATS_SUMSQ_BASE=256 STEPPER_BOTH_EDGE=1
mcu_temperature 'mcu' nominal base=-263.822394 slope=1581.081081
mcu_temperature 'toolboard_t0' nominal base=-262.550143 slope=1290.687679
mcu_temperature 'toolboard_t1' nominal base=-272.332362 slope=1313.265306
mcu 'beacon': Starting serial connect
Loaded MCU 'beacon' 45 commands (Beacon 2.1.0 / )
MCU 'beacon' config: ADC_MAX=4095 BEACON_ACCEL_BITS=12 BEACON_ACCEL_SCALE_16G=7.81 BEACON_ACCEL_SCALE_2G=0.98 BEACON_ACCEL_SCALE_4G=1.95 BEACON_ACCEL_SCALE_8G=3.91 BEACON_ADC_SMOOTH_COUNT=16 BEACON_HAS_ACCEL=1 BEACON_REV=H CLOCK_FREQ=32000000 MCU=beacon STATS_SUMSQ_BASE=256
Sending MCU 'mcu' printer configuration...
Configured MCU 'mcu' (1024 moves)
Sending MCU 'rpi' printer configuration...
Configured MCU 'rpi' (1024 moves)
Sending MCU 'toolboard_t0' printer configuration...
Configured MCU 'toolboard_t0' (1024 moves)
Sending MCU 'toolboard_t1' printer configuration...
Configured MCU 'toolboard_t1' (1024 moves)
Sending MCU 'dinghy' printer configuration...
Configured MCU 'dinghy' (1024 moves)
Sending MCU 'plasma' printer configuration...
Configured MCU 'plasma' (1024 moves)
Starting heater checks for heater_bed
beacon: loaded fnorm=5106174.70 temp=18.98 amfg=1.012 from nvm
beacon: built tempco model version 1 {'amfg': 1.0116254092446901, 'tcc': -7.155348984545153e-06, 'tcfl': -0.0006342204102343939, 'tctl': 0.001940863247628072, 'fmin': 5106174.703687429, 'fmin_temp': 18.98276710510254}
Enabling Beacon accelerometer
Selected Beacon accelerometer scale 16g
Sending MCU 'beacon' printer configuration...
Configured MCU 'beacon' (0 moves)
beacon_user_z_offset: beacon_contact_start_print_true_zero is enabled, activating beacon user z-offset management. Applying configured z_offset of 0.0 mm to named offset 'user_probe_z_offset'.
Starting heater checks for extruder
Starting heater checks for extruder1
Write g-code response
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/gcode.py", line 459, in _respond_raw
    os.write(self.fd, (msg+"\n").encode())
BlockingIOError: [Errno 11] Resource temporarily unavailable
Stats 9074.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000002 mcu_task_stddev=0.000001 bytes_write=4544 bytes_read=7779 bytes_retransmit=9 bytes_invalid=0 send_seq=339 receive_seq=339 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400014353 rpi: mcu_awake=0.003 mcu_task_avg=0.000018 mcu_task_stddev=0.000009 bytes_write=886 bytes_read=4726 bytes_retransmit=0 bytes_invalid=0 send_seq=119 receive_seq=119 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49998852 adj=49990895 toolboard_t0: mcu_awake=0.008 mcu_task_avg=0.000022 mcu_task_stddev=0.000021 bytes_write=1438 bytes_read=5031 bytes_retransmit=9 bytes_invalid=0 send_seq=155 receive_seq=155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999929 adj=63995894 toolboard_t1: mcu_awake=0.008 mcu_task_avg=0.000022 mcu_task_stddev=0.000021 bytes_write=1432 bytes_read=5015 bytes_retransmit=9 bytes_invalid=0 send_seq=154 receive_seq=154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999402 adj=63994836 dinghy: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1023 bytes_read=4453 bytes_retransmit=9 bytes_invalid=0 send_seq=124 receive_seq=124 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999383 adj=47999208 plasma: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1682 bytes_read=4737 bytes_retransmit=9 bytes_invalid=0 send_seq=133 receive_seq=133 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999659 adj=11998888 Octopus_Pro_H723_V1.1: temp=0.0 EBB42_Gen2_v1.0_T0: temp=0.0 EBB42_Gen2_v1.0_T1: temp=0.0 raspberry_pi: temp=28.7  heater_bed: target=0 temp=0.0 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=374 bytes_read=1986 bytes_retransmit=0 bytes_invalid=0 send_seq=61 receive_seq=61 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=32000361 adj=31999531 coil_temp=17.0 refs=0 mcu_temp=20.38 supply_voltage=3.011 th0: temp=0.0 th1: temp=0.0 th2: temp=0.0 th3: temp=0.0 sysload=1.03 cputime=656.927 memavail=7397640 print_time=12.676 buffer_time=0.262 print_stall=0 extruder: target=0 temp=0.0 pwm=0.000 extruder1: target=0 temp=0.0 pwm=0.000
Initializing RatOS...
CALCULATE_PRINTABLE_AREA: Printable area calculated: X: 0,500.0 Y: 0,500.0
toolhead: max_velocity: 600.000000
max_accel: 8000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
Extruder extruder already active
Extruder 'extruder' now syncing with 'extruder'
Extruder 'extruder1' now syncing with 'extruder1'
shaper_type_x:mzv shaper_freq_x:54.200 damping_ratio_x:0.100000
shaper_type_y:mzv shaper_freq_y:40.800 damping_ratio_y:0.100000
toolhead: max_velocity: 800.000000
max_accel: 10000.000000
minimum_cruise_ratio: 0.500000
square_corner_velocity: 5.000000
webhooks: registering remote method 'shutdown_machine' for connection id: 3978002616
webhooks: registering remote method 'reboot_machine' for connection id: 3978002616
webhooks: registering remote method 'pause_job_queue' for connection id: 3978002616
webhooks: registering remote method 'start_job_queue' for connection id: 3978002616
ratos: beacon probing regions updated: BeaconProbingRegions(x_offset=0.0, y_offset=27.5, printable_x_max=500.0, printable_y_max=500.0, mesh_proximity_min_coil_pos=(20.0, 20.0), mesh_proximity_max_coil_pos=(480.0, 480.0), mesh_proximity_min_toolhead_pos=(20.0, -7.5), mesh_proximity_max_toolhead_pos=(480.0, 452.5), mesh_contact_min=(20.0, 20.0), mesh_contact_max=(480.0, 480.0), logical_proximity_min_coil_pos=(20.0, 20.0), logical_proximity_max_coil_pos=(480.0, 480.0), logical_proximity_min_toolhead_pos=(20.0, -7.5), logical_proximity_max_toolhead_pos=(480.0, 452.5), logical_contact_min=(10.0, -17.5), logical_contact_max=(490.0, 462.5))
Stats 9075.3: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000002 mcu_task_stddev=0.000001 bytes_write=4550 bytes_read=7824 bytes_retransmit=9 bytes_invalid=0 send_seq=340 receive_seq=340 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016186 rpi: mcu_awake=0.003 mcu_task_avg=0.000018 mcu_task_stddev=0.000009 bytes_write=892 bytes_read=4742 bytes_retransmit=0 bytes_invalid=0 send_seq=120 receive_seq=120 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999121 adj=50004034 toolboard_t0: mcu_awake=0.008 mcu_task_avg=0.000022 mcu_task_stddev=0.000021 bytes_write=1444 bytes_read=5103 bytes_retransmit=9 bytes_invalid=0 send_seq=156 receive_seq=156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000191 adj=63999240 toolboard_t1: mcu_awake=0.008 mcu_task_avg=0.000022 mcu_task_stddev=0.000021 bytes_write=1438 bytes_read=5087 bytes_retransmit=9 bytes_invalid=0 send_seq=155 receive_seq=155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=63999802 adj=63998828 dinghy: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1029 bytes_read=4625 bytes_retransmit=9 bytes_invalid=0 send_seq=125 receive_seq=125 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999475 adj=47996593 plasma: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=1688 bytes_read=4752 bytes_retransmit=9 bytes_invalid=0 send_seq=134 receive_seq=134 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999823 adj=11999391 Octopus_Pro_H723_V1.1: temp=33.6 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.4 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=380 bytes_read=2342 bytes_retransmit=0 bytes_invalid=0 send_seq=62 receive_seq=62 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=32000017 adj=31999096 coil_temp=17.0 refs=0 mcu_temp=20.39 supply_voltage=3.011 th0: temp=46.0 th1: temp=46.1 th2: temp=50.4 th3: temp=49.6 sysload=1.03 cputime=657.117 memavail=7393632 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.3 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
HELLO_RATOS: version: v2.1.0-0-g0be29e9d, distro: RatOS v2.1.0-RC4 (bullseye)
No deferred RatOS console messages to write.
ratos: Current CPU governor(s): performance
Stats 9076.9: gcodein=0  mcu: mcu_awake=0.001 mcu_task_avg=0.000002 mcu_task_stddev=0.000001 bytes_write=4556 bytes_read=7985 bytes_retransmit=9 bytes_invalid=0 send_seq=341 receive_seq=341 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016540 rpi: mcu_awake=0.003 mcu_task_avg=0.000018 mcu_task_stddev=0.000009 bytes_write=904 bytes_read=4774 bytes_retransmit=0 bytes_invalid=0 send_seq=122 receive_seq=122 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999414 adj=50002810 toolboard_t0: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000030 bytes_write=1450 bytes_read=5274 bytes_retransmit=9 bytes_invalid=0 send_seq=157 receive_seq=157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000216 adj=63998798 toolboard_t1: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000030 bytes_write=1450 bytes_read=5274 bytes_retransmit=9 bytes_invalid=0 send_seq=157 receive_seq=157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000118 adj=63998602 dinghy: mcu_awake=0.014 mcu_task_avg=0.000030 mcu_task_stddev=0.000042 bytes_write=1035 bytes_read=4992 bytes_retransmit=9 bytes_invalid=0 send_seq=126 receive_seq=126 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47996432 plasma: mcu_awake=0.010 mcu_task_avg=0.000021 mcu_task_stddev=0.000265 bytes_write=1694 bytes_read=4782 bytes_retransmit=9 bytes_invalid=0 send_seq=135 receive_seq=135 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=12000023 adj=11999503 Octopus_Pro_H723_V1.1: temp=33.6 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=392 bytes_read=2884 bytes_retransmit=0 bytes_invalid=0 send_seq=64 receive_seq=64 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=32000041 adj=31998245 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=45.9 th1: temp=46.2 th2: temp=50.5 th3: temp=49.5 sysload=1.03 cputime=657.396 memavail=7394292 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.3 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9077.9: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000006 mcu_task_stddev=0.000011 bytes_write=4562 bytes_read=8132 bytes_retransmit=9 bytes_invalid=0 send_seq=342 receive_seq=342 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016611 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000020 bytes_write=910 bytes_read=4803 bytes_retransmit=0 bytes_invalid=0 send_seq=123 receive_seq=123 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999327 adj=50001254 toolboard_t0: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000030 bytes_write=1456 bytes_read=5374 bytes_retransmit=9 bytes_invalid=0 send_seq=158 receive_seq=158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000221 adj=63998242 toolboard_t1: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000030 bytes_write=1456 bytes_read=5374 bytes_retransmit=9 bytes_invalid=0 send_seq=158 receive_seq=158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63998649 dinghy: mcu_awake=0.014 mcu_task_avg=0.000030 mcu_task_stddev=0.000042 bytes_write=1041 bytes_read=5224 bytes_retransmit=9 bytes_invalid=0 send_seq=127 receive_seq=127 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999584 adj=47996893 plasma: mcu_awake=0.010 mcu_task_avg=0.000021 mcu_task_stddev=0.000265 bytes_write=1700 bytes_read=4797 bytes_retransmit=9 bytes_invalid=0 send_seq=136 receive_seq=136 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999969 adj=11999819 Octopus_Pro_H723_V1.1: temp=33.4 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=398 bytes_read=3240 bytes_retransmit=0 bytes_invalid=0 send_seq=65 receive_seq=65 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=32000014 adj=31998398 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=46.0 th1: temp=46.1 th2: temp=50.5 th3: temp=49.6 sysload=0.95 cputime=657.432 memavail=7394316 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.3 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 9078.9: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000006 mcu_task_stddev=0.000011 bytes_write=4568 bytes_read=8235 bytes_retransmit=9 bytes_invalid=0 send_seq=343 receive_seq=343 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400016217 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000020 bytes_write=916 bytes_read=4819 bytes_retransmit=0 bytes_invalid=0 send_seq=124 receive_seq=124 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999276 adj=50000001 toolboard_t0: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000030 bytes_write=1462 bytes_read=5488 bytes_retransmit=9 bytes_invalid=0 send_seq=159 receive_seq=159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000180 adj=63998054 toolboard_t1: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000030 bytes_write=1462 bytes_read=5488 bytes_retransmit=9 bytes_invalid=0 send_seq=159 receive_seq=159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000024 adj=63998150 dinghy: mcu_awake=0.014 mcu_task_avg=0.000030 mcu_task_stddev=0.000042 bytes_write=1047 bytes_read=5516 bytes_retransmit=9 bytes_invalid=0 send_seq=128 receive_seq=128 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999581 adj=47997132 plasma: mcu_awake=0.010 mcu_task_avg=0.000021 mcu_task_stddev=0.000265 bytes_write=1706 bytes_read=4812 bytes_retransmit=9 bytes_invalid=0 send_seq=137 receive_seq=137 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999930 adj=11999616 Octopus_Pro_H723_V1.1: temp=33.6 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=404 bytes_read=3596 bytes_retransmit=0 bytes_invalid=0 send_seq=66 receive_seq=66 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998402 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=46.0 th1: temp=46.2 th2: temp=50.4 th3: temp=49.4 sysload=0.95 cputime=657.466 memavail=7394316 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.2 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 9079.9: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000006 mcu_task_stddev=0.000011 bytes_write=4580 bytes_read=8354 bytes_retransmit=9 bytes_invalid=0 send_seq=345 receive_seq=345 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015837 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000020 bytes_write=922 bytes_read=4835 bytes_retransmit=0 bytes_invalid=0 send_seq=125 receive_seq=125 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999234 adj=49999313 toolboard_t0: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000030 bytes_write=1468 bytes_read=5602 bytes_retransmit=9 bytes_invalid=0 send_seq=160 receive_seq=160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000219 adj=63998013 toolboard_t1: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000030 bytes_write=1468 bytes_read=5602 bytes_retransmit=9 bytes_invalid=0 send_seq=160 receive_seq=160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000008 adj=63998087 dinghy: mcu_awake=0.014 mcu_task_avg=0.000030 mcu_task_stddev=0.000042 bytes_write=1053 bytes_read=5748 bytes_retransmit=9 bytes_invalid=0 send_seq=129 receive_seq=129 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997391 plasma: mcu_awake=0.010 mcu_task_avg=0.000021 mcu_task_stddev=0.000265 bytes_write=1712 bytes_read=4828 bytes_retransmit=9 bytes_invalid=0 send_seq=138 receive_seq=138 retransmit_seq=2 srtt=0.001 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999529 Octopus_Pro_H723_V1.1: temp=33.6 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=410 bytes_read=3952 bytes_retransmit=0 bytes_invalid=0 send_seq=67 receive_seq=67 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999905 adj=31998416 coil_temp=17.0 refs=0 mcu_temp=20.38 supply_voltage=3.012 th0: temp=45.9 th1: temp=46.1 th2: temp=50.3 th3: temp=49.5 sysload=0.95 cputime=657.500 memavail=7394316 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.3 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 9080.9: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000006 mcu_task_stddev=0.000011 bytes_write=4586 bytes_read=8486 bytes_retransmit=9 bytes_invalid=0 send_seq=346 receive_seq=346 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015656 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000020 bytes_write=928 bytes_read=4851 bytes_retransmit=0 bytes_invalid=0 send_seq=126 receive_seq=126 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999217 adj=49998821 toolboard_t0: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000030 bytes_write=1474 bytes_read=5702 bytes_retransmit=9 bytes_invalid=0 send_seq=161 receive_seq=161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000206 adj=63998238 toolboard_t1: mcu_awake=0.005 mcu_task_avg=0.000019 mcu_task_stddev=0.000030 bytes_write=1474 bytes_read=5702 bytes_retransmit=9 bytes_invalid=0 send_seq=161 receive_seq=161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000005 adj=63998081 dinghy: mcu_awake=0.014 mcu_task_avg=0.000030 mcu_task_stddev=0.000042 bytes_write=1059 bytes_read=5980 bytes_retransmit=9 bytes_invalid=0 send_seq=130 receive_seq=130 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997525 plasma: mcu_awake=0.010 mcu_task_avg=0.000021 mcu_task_stddev=0.000265 bytes_write=1724 bytes_read=4860 bytes_retransmit=9 bytes_invalid=0 send_seq=140 receive_seq=140 retransmit_seq=2 srtt=0.000 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999907 adj=11999506 Octopus_Pro_H723_V1.1: temp=33.6 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=416 bytes_read=4308 bytes_retransmit=0 bytes_invalid=0 send_seq=68 receive_seq=68 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=32000082 adj=31998479 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=45.8 th1: temp=46.1 th2: temp=50.4 th3: temp=49.5 sysload=0.95 cputime=657.533 memavail=7394212 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.3 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9081.9: gcodein=0  mcu: mcu_awake=0.004 mcu_task_avg=0.000006 mcu_task_stddev=0.000011 bytes_write=4592 bytes_read=8589 bytes_retransmit=9 bytes_invalid=0 send_seq=347 receive_seq=347 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015592 rpi: mcu_awake=0.001 mcu_task_avg=0.000013 mcu_task_stddev=0.000020 bytes_write=934 bytes_read=4867 bytes_retransmit=0 bytes_invalid=0 send_seq=127 receive_seq=127 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999212 adj=49998452 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1480 bytes_read=5830 bytes_retransmit=9 bytes_invalid=0 send_seq=162 receive_seq=162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63998162 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1480 bytes_read=5830 bytes_retransmit=9 bytes_invalid=0 send_seq=162 receive_seq=162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000002 adj=63998026 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1065 bytes_read=6287 bytes_retransmit=9 bytes_invalid=0 send_seq=131 receive_seq=131 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997597 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1730 bytes_read=4887 bytes_retransmit=9 bytes_invalid=0 send_seq=141 receive_seq=141 retransmit_seq=2 srtt=0.000 rttvar=0.001 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999903 adj=11999485 Octopus_Pro_H723_V1.1: temp=33.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=422 bytes_read=4664 bytes_retransmit=0 bytes_invalid=0 send_seq=69 receive_seq=69 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=32000009 adj=31999072 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=45.8 th1: temp=46.0 th2: temp=50.3 th3: temp=49.5 sysload=0.95 cputime=657.565 memavail=7394332 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.3 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9082.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4598 bytes_read=8706 bytes_retransmit=9 bytes_invalid=0 send_seq=348 receive_seq=348 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015670 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=940 bytes_read=4896 bytes_retransmit=0 bytes_invalid=0 send_seq=128 receive_seq=128 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999221 adj=49998166 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1492 bytes_read=5960 bytes_retransmit=9 bytes_invalid=0 send_seq=164 receive_seq=164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000201 adj=63998073 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1486 bytes_read=5944 bytes_retransmit=9 bytes_invalid=0 send_seq=163 receive_seq=163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000003 adj=63997923 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1071 bytes_read=6519 bytes_retransmit=9 bytes_invalid=0 send_seq=132 receive_seq=132 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999547 adj=47997682 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1736 bytes_read=4903 bytes_retransmit=9 bytes_invalid=0 send_seq=142 receive_seq=142 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999469 Octopus_Pro_H723_V1.1: temp=33.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=428 bytes_read=5020 bytes_retransmit=0 bytes_invalid=0 send_seq=70 receive_seq=70 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999971 adj=31998808 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=45.8 th1: temp=46.0 th2: temp=50.3 th3: temp=49.4 sysload=0.87 cputime=657.598 memavail=7394332 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9083.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4604 bytes_read=8831 bytes_retransmit=9 bytes_invalid=0 send_seq=349 receive_seq=349 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015607 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=946 bytes_read=4912 bytes_retransmit=0 bytes_invalid=0 send_seq=129 receive_seq=129 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999229 adj=49997933 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1498 bytes_read=6060 bytes_retransmit=9 bytes_invalid=0 send_seq=165 receive_seq=165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000204 adj=63997927 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1492 bytes_read=6044 bytes_retransmit=9 bytes_invalid=0 send_seq=164 receive_seq=164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997772 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1077 bytes_read=6751 bytes_retransmit=9 bytes_invalid=0 send_seq=133 receive_seq=133 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997628 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1742 bytes_read=4919 bytes_retransmit=9 bytes_invalid=0 send_seq=143 receive_seq=143 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999927 adj=11999485 Octopus_Pro_H723_V1.1: temp=33.9 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=434 bytes_read=5376 bytes_retransmit=0 bytes_invalid=0 send_seq=71 receive_seq=71 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=32000004 adj=31998647 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=45.8 th1: temp=46.0 th2: temp=50.2 th3: temp=49.4 sysload=0.87 cputime=657.634 memavail=7394712 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 9084.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4610 bytes_read=8934 bytes_retransmit=9 bytes_invalid=0 send_seq=350 receive_seq=350 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015539 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=952 bytes_read=4928 bytes_retransmit=0 bytes_invalid=0 send_seq=130 receive_seq=130 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999222 adj=49997834 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1504 bytes_read=6174 bytes_retransmit=9 bytes_invalid=0 send_seq=166 receive_seq=166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000214 adj=63997923 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1498 bytes_read=6158 bytes_retransmit=9 bytes_invalid=0 send_seq=165 receive_seq=165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000004 adj=63997749 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1083 bytes_read=7043 bytes_retransmit=9 bytes_invalid=0 send_seq=134 receive_seq=134 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997676 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1748 bytes_read=4935 bytes_retransmit=9 bytes_invalid=0 send_seq=144 receive_seq=144 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999532 Octopus_Pro_H723_V1.1: temp=33.7 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=440 bytes_read=5732 bytes_retransmit=0 bytes_invalid=0 send_seq=72 receive_seq=72 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999986 adj=31998801 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=45.8 th1: temp=46.0 th2: temp=50.3 th3: temp=49.4 sysload=0.87 cputime=657.667 memavail=7394712 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.3 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9085.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4616 bytes_read=9037 bytes_retransmit=9 bytes_invalid=0 send_seq=351 receive_seq=351 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015568 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=958 bytes_read=4944 bytes_retransmit=0 bytes_invalid=0 send_seq=131 receive_seq=131 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999216 adj=49997704 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1510 bytes_read=6288 bytes_retransmit=9 bytes_invalid=0 send_seq=167 receive_seq=167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997959 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1504 bytes_read=6272 bytes_retransmit=9 bytes_invalid=0 send_seq=166 receive_seq=166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000029 adj=63997741 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1089 bytes_read=7275 bytes_retransmit=9 bytes_invalid=0 send_seq=135 receive_seq=135 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999549 adj=47997693 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1754 bytes_read=4951 bytes_retransmit=9 bytes_invalid=0 send_seq=145 receive_seq=145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999496 Octopus_Pro_H723_V1.1: temp=33.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=446 bytes_read=6088 bytes_retransmit=0 bytes_invalid=0 send_seq=73 receive_seq=73 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999966 adj=31998748 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=45.8 th1: temp=46.0 th2: temp=50.3 th3: temp=49.4 sysload=0.87 cputime=657.699 memavail=7394712 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.3 pwm=0.000 extruder1: target=0 temp=17.5 pwm=0.000
Stats 9086.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4622 bytes_read=9169 bytes_retransmit=9 bytes_invalid=0 send_seq=352 receive_seq=352 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015524 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=964 bytes_read=4960 bytes_retransmit=0 bytes_invalid=0 send_seq=132 receive_seq=132 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999218 adj=49997549 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1516 bytes_read=6388 bytes_retransmit=9 bytes_invalid=0 send_seq=168 receive_seq=168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997935 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1510 bytes_read=6386 bytes_retransmit=9 bytes_invalid=0 send_seq=167 receive_seq=167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000030 adj=63997770 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1095 bytes_read=7507 bytes_retransmit=9 bytes_invalid=0 send_seq=136 receive_seq=136 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999565 adj=47997697 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1760 bytes_read=4978 bytes_retransmit=9 bytes_invalid=0 send_seq=146 receive_seq=146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999912 adj=11999464 Octopus_Pro_H723_V1.1: temp=33.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=452 bytes_read=6444 bytes_retransmit=0 bytes_invalid=0 send_seq=74 receive_seq=74 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999947 adj=31998655 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=45.8 th1: temp=46.0 th2: temp=50.3 th3: temp=49.4 sysload=0.87 cputime=657.731 memavail=7394712 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.5 pwm=0.000 extruder1: target=0 temp=17.5 pwm=0.000
Stats 9087.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4628 bytes_read=9286 bytes_retransmit=9 bytes_invalid=0 send_seq=353 receive_seq=353 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015485 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=970 bytes_read=4989 bytes_retransmit=0 bytes_invalid=0 send_seq=133 receive_seq=133 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999245 adj=49997518 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1522 bytes_read=6516 bytes_retransmit=9 bytes_invalid=0 send_seq=169 receive_seq=169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000209 adj=63997890 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1516 bytes_read=6500 bytes_retransmit=9 bytes_invalid=0 send_seq=168 receive_seq=168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000039 adj=63997751 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1101 bytes_read=7814 bytes_retransmit=9 bytes_invalid=0 send_seq=137 receive_seq=137 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999556 adj=47997788 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1766 bytes_read=4994 bytes_retransmit=9 bytes_invalid=0 send_seq=147 receive_seq=147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999453 Octopus_Pro_H723_V1.1: temp=33.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=458 bytes_read=6800 bytes_retransmit=0 bytes_invalid=0 send_seq=75 receive_seq=75 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999943 adj=31998613 coil_temp=17.0 refs=0 mcu_temp=20.41 supply_voltage=3.012 th0: temp=45.8 th1: temp=45.9 th2: temp=50.2 th3: temp=49.3 sysload=0.80 cputime=657.765 memavail=7394712 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9088.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4634 bytes_read=9389 bytes_retransmit=9 bytes_invalid=0 send_seq=354 receive_seq=354 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015463 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=976 bytes_read=5005 bytes_retransmit=0 bytes_invalid=0 send_seq=134 receive_seq=134 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997617 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1528 bytes_read=6630 bytes_retransmit=9 bytes_invalid=0 send_seq=170 receive_seq=170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000202 adj=63997834 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1522 bytes_read=6614 bytes_retransmit=9 bytes_invalid=0 send_seq=169 receive_seq=169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000036 adj=63997774 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1107 bytes_read=8046 bytes_retransmit=9 bytes_invalid=0 send_seq=138 receive_seq=138 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997750 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1772 bytes_read=5010 bytes_retransmit=9 bytes_invalid=0 send_seq=148 receive_seq=148 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999911 adj=11999451 Octopus_Pro_H723_V1.1: temp=33.7 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.1 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=464 bytes_read=7156 bytes_retransmit=0 bytes_invalid=0 send_seq=76 receive_seq=76 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999939 adj=31998635 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=45.8 th1: temp=45.9 th2: temp=50.2 th3: temp=49.4 sysload=0.80 cputime=657.798 memavail=7394228 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 9089.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4640 bytes_read=9521 bytes_retransmit=9 bytes_invalid=0 send_seq=355 receive_seq=355 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015462 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=982 bytes_read=5021 bytes_retransmit=0 bytes_invalid=0 send_seq=135 receive_seq=135 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999255 adj=49997594 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1534 bytes_read=6730 bytes_retransmit=9 bytes_invalid=0 send_seq=171 receive_seq=171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000196 adj=63997787 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1528 bytes_read=6714 bytes_retransmit=9 bytes_invalid=0 send_seq=170 receive_seq=170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000038 adj=63997726 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1113 bytes_read=8278 bytes_retransmit=9 bytes_invalid=0 send_seq=139 receive_seq=139 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997731 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1778 bytes_read=5026 bytes_retransmit=9 bytes_invalid=0 send_seq=149 receive_seq=149 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999452 Octopus_Pro_H723_V1.1: temp=33.7 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=470 bytes_read=7512 bytes_retransmit=0 bytes_invalid=0 send_seq=77 receive_seq=77 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999954 adj=31998643 coil_temp=17.0 refs=0 mcu_temp=20.39 supply_voltage=3.012 th0: temp=45.8 th1: temp=45.9 th2: temp=50.3 th3: temp=49.3 sysload=0.80 cputime=657.830 memavail=7394228 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9090.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4646 bytes_read=9624 bytes_retransmit=9 bytes_invalid=0 send_seq=356 receive_seq=356 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015449 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=988 bytes_read=5037 bytes_retransmit=0 bytes_invalid=0 send_seq=136 receive_seq=136 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999252 adj=49997541 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1540 bytes_read=6844 bytes_retransmit=9 bytes_invalid=0 send_seq=172 receive_seq=172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000194 adj=63997742 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1534 bytes_read=6828 bytes_retransmit=9 bytes_invalid=0 send_seq=171 receive_seq=171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000048 adj=63997697 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1119 bytes_read=8570 bytes_retransmit=9 bytes_invalid=0 send_seq=140 receive_seq=140 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997702 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1784 bytes_read=5042 bytes_retransmit=9 bytes_invalid=0 send_seq=150 receive_seq=150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999446 Octopus_Pro_H723_V1.1: temp=33.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=476 bytes_read=7868 bytes_retransmit=0 bytes_invalid=0 send_seq=78 receive_seq=78 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999955 adj=31998729 coil_temp=17.0 refs=0 mcu_temp=20.38 supply_voltage=3.012 th0: temp=45.7 th1: temp=45.8 th2: temp=50.2 th3: temp=49.3 sysload=0.80 cputime=657.862 memavail=7394228 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 9091.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4652 bytes_read=9727 bytes_retransmit=9 bytes_invalid=0 send_seq=357 receive_seq=357 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015452 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=994 bytes_read=5053 bytes_retransmit=0 bytes_invalid=0 send_seq=137 receive_seq=137 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999246 adj=49997479 toolboard_t0: mcu_awake=0.003 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1546 bytes_read=6958 bytes_retransmit=9 bytes_invalid=0 send_seq=173 receive_seq=173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000203 adj=63997738 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1540 bytes_read=6942 bytes_retransmit=9 bytes_invalid=0 send_seq=172 receive_seq=172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997728 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1125 bytes_read=8802 bytes_retransmit=9 bytes_invalid=0 send_seq=141 receive_seq=141 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997742 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1790 bytes_read=5069 bytes_retransmit=9 bytes_invalid=0 send_seq=151 receive_seq=151 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999910 adj=11999449 Octopus_Pro_H723_V1.1: temp=33.7 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=482 bytes_read=8224 bytes_retransmit=0 bytes_invalid=0 send_seq=79 receive_seq=79 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999944 adj=31998738 coil_temp=17.0 refs=0 mcu_temp=20.37 supply_voltage=3.012 th0: temp=45.7 th1: temp=45.9 th2: temp=50.1 th3: temp=49.3 sysload=0.80 cputime=657.895 memavail=7394228 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.2 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9092.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4658 bytes_read=9873 bytes_retransmit=9 bytes_invalid=0 send_seq=358 receive_seq=358 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015448 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1000 bytes_read=5082 bytes_retransmit=0 bytes_invalid=0 send_seq=138 receive_seq=138 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999237 adj=49997402 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1552 bytes_read=7072 bytes_retransmit=9 bytes_invalid=0 send_seq=174 receive_seq=174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000207 adj=63997787 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1546 bytes_read=7056 bytes_retransmit=9 bytes_invalid=0 send_seq=173 receive_seq=173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000045 adj=63997674 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1131 bytes_read=9049 bytes_retransmit=9 bytes_invalid=0 send_seq=142 receive_seq=142 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997714 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1796 bytes_read=5085 bytes_retransmit=9 bytes_invalid=0 send_seq=152 receive_seq=152 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999909 adj=11999452 Octopus_Pro_H723_V1.1: temp=33.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=488 bytes_read=8580 bytes_retransmit=0 bytes_invalid=0 send_seq=80 receive_seq=80 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998675 coil_temp=17.0 refs=0 mcu_temp=20.36 supply_voltage=3.012 th0: temp=45.7 th1: temp=45.9 th2: temp=50.2 th3: temp=49.2 sysload=0.74 cputime=657.928 memavail=7394228 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 9093.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4664 bytes_read=9974 bytes_retransmit=9 bytes_invalid=0 send_seq=359 receive_seq=359 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015568 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1006 bytes_read=5098 bytes_retransmit=0 bytes_invalid=0 send_seq=139 receive_seq=139 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999236 adj=49997333 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1558 bytes_read=7186 bytes_retransmit=9 bytes_invalid=0 send_seq=175 receive_seq=175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000208 adj=63997797 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1552 bytes_read=7170 bytes_retransmit=9 bytes_invalid=0 send_seq=174 receive_seq=174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000049 adj=63997652 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1137 bytes_read=9341 bytes_retransmit=9 bytes_invalid=0 send_seq=143 receive_seq=143 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997708 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1802 bytes_read=5101 bytes_retransmit=9 bytes_invalid=0 send_seq=153 receive_seq=153 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999913 adj=11999446 Octopus_Pro_H723_V1.1: temp=33.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=27.3  heater_bed: target=0 temp=16.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=494 bytes_read=8936 bytes_retransmit=0 bytes_invalid=0 send_seq=81 receive_seq=81 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998641 coil_temp=17.0 refs=0 mcu_temp=20.36 supply_voltage=3.012 th0: temp=45.7 th1: temp=45.9 th2: temp=50.1 th3: temp=49.2 sysload=0.74 cputime=657.969 memavail=7393372 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.2 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 9094.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4670 bytes_read=10075 bytes_retransmit=9 bytes_invalid=0 send_seq=360 receive_seq=360 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015573 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1012 bytes_read=5114 bytes_retransmit=0 bytes_invalid=0 send_seq=140 receive_seq=140 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999251 adj=49997222 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1564 bytes_read=7300 bytes_retransmit=9 bytes_invalid=0 send_seq=176 receive_seq=176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000213 adj=63997671 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1558 bytes_read=7284 bytes_retransmit=9 bytes_invalid=0 send_seq=175 receive_seq=175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000050 adj=63997532 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1143 bytes_read=9573 bytes_retransmit=9 bytes_invalid=0 send_seq=144 receive_seq=144 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1808 bytes_read=5117 bytes_retransmit=9 bytes_invalid=0 send_seq=154 receive_seq=154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999442 Octopus_Pro_H723_V1.1: temp=33.9 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=500 bytes_read=9292 bytes_retransmit=0 bytes_invalid=0 send_seq=82 receive_seq=82 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998599 coil_temp=17.0 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=45.5 th1: temp=45.9 th2: temp=50.1 th3: temp=49.2 sysload=0.74 cputime=658.013 memavail=7393328 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.2 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 9095.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4676 bytes_read=10207 bytes_retransmit=9 bytes_invalid=0 send_seq=361 receive_seq=361 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015580 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1018 bytes_read=5130 bytes_retransmit=0 bytes_invalid=0 send_seq=141 receive_seq=141 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999268 adj=49997335 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1570 bytes_read=7400 bytes_retransmit=9 bytes_invalid=0 send_seq=177 receive_seq=177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997704 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1564 bytes_read=7384 bytes_retransmit=9 bytes_invalid=0 send_seq=176 receive_seq=176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997545 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1149 bytes_read=9805 bytes_retransmit=9 bytes_invalid=0 send_seq=145 receive_seq=145 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997611 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1814 bytes_read=5133 bytes_retransmit=9 bytes_invalid=0 send_seq=155 receive_seq=155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999477 Octopus_Pro_H723_V1.1: temp=33.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=506 bytes_read=9648 bytes_retransmit=0 bytes_invalid=0 send_seq=83 receive_seq=83 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998615 coil_temp=17.0 refs=0 mcu_temp=20.34 supply_voltage=3.012 th0: temp=45.6 th1: temp=46.0 th2: temp=50.1 th3: temp=49.2 sysload=0.74 cputime=658.055 memavail=7380372 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.2 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 9096.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4682 bytes_read=10310 bytes_retransmit=9 bytes_invalid=0 send_seq=362 receive_seq=362 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015583 rpi: mcu_awake=0.000 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1024 bytes_read=5146 bytes_retransmit=0 bytes_invalid=0 send_seq=142 receive_seq=142 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999276 adj=49997431 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1576 bytes_read=7514 bytes_retransmit=9 bytes_invalid=0 send_seq=178 receive_seq=178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000218 adj=63997733 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1570 bytes_read=7498 bytes_retransmit=9 bytes_invalid=0 send_seq=177 receive_seq=177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997596 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1155 bytes_read=10097 bytes_retransmit=9 bytes_invalid=0 send_seq=146 receive_seq=146 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997611 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1820 bytes_read=5160 bytes_retransmit=9 bytes_invalid=0 send_seq=156 receive_seq=156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999485 Octopus_Pro_H723_V1.1: temp=33.7 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=512 bytes_read=10004 bytes_retransmit=0 bytes_invalid=0 send_seq=84 receive_seq=84 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998614 coil_temp=17.0 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=45.6 th1: temp=45.8 th2: temp=50.1 th3: temp=49.2 sysload=0.74 cputime=658.098 memavail=7366748 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.2 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9097.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4688 bytes_read=10427 bytes_retransmit=9 bytes_invalid=0 send_seq=363 receive_seq=363 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015601 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1030 bytes_read=5175 bytes_retransmit=0 bytes_invalid=0 send_seq=143 receive_seq=143 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999282 adj=49997457 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1582 bytes_read=7642 bytes_retransmit=9 bytes_invalid=0 send_seq=179 receive_seq=179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997733 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1576 bytes_read=7626 bytes_retransmit=9 bytes_invalid=0 send_seq=178 receive_seq=178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997585 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1161 bytes_read=10344 bytes_retransmit=9 bytes_invalid=0 send_seq=147 receive_seq=147 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999546 adj=47997621 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1826 bytes_read=5176 bytes_retransmit=9 bytes_invalid=0 send_seq=157 receive_seq=157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999473 Octopus_Pro_H723_V1.1: temp=33.7 EBB42_Gen2_v1.0_T0: temp=30.3 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=518 bytes_read=10360 bytes_retransmit=0 bytes_invalid=0 send_seq=85 receive_seq=85 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998620 coil_temp=17.0 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=45.6 th1: temp=45.8 th2: temp=50.1 th3: temp=49.2 sysload=0.76 cputime=658.144 memavail=7357248 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.2 pwm=0.000 extruder1: target=0 temp=17.4 pwm=0.000
Stats 9098.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4694 bytes_read=10559 bytes_retransmit=9 bytes_invalid=0 send_seq=364 receive_seq=364 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015612 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1036 bytes_read=5191 bytes_retransmit=0 bytes_invalid=0 send_seq=144 receive_seq=144 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999288 adj=49997446 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1588 bytes_read=7742 bytes_retransmit=9 bytes_invalid=0 send_seq=180 receive_seq=180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997736 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1582 bytes_read=7726 bytes_retransmit=9 bytes_invalid=0 send_seq=179 receive_seq=179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000063 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1167 bytes_read=10576 bytes_retransmit=9 bytes_invalid=0 send_seq=148 receive_seq=148 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997622 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1832 bytes_read=5192 bytes_retransmit=9 bytes_invalid=0 send_seq=158 receive_seq=158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999468 Octopus_Pro_H723_V1.1: temp=33.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=524 bytes_read=10716 bytes_retransmit=0 bytes_invalid=0 send_seq=86 receive_seq=86 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998630 coil_temp=17.0 refs=0 mcu_temp=20.37 supply_voltage=3.012 th0: temp=45.6 th1: temp=45.8 th2: temp=50.1 th3: temp=49.3 sysload=0.76 cputime=658.188 memavail=7360540 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.5 pwm=0.000
Stats 9099.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4700 bytes_read=10662 bytes_retransmit=9 bytes_invalid=0 send_seq=365 receive_seq=365 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015619 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1042 bytes_read=5207 bytes_retransmit=0 bytes_invalid=0 send_seq=145 receive_seq=145 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999296 adj=49997454 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1594 bytes_read=7856 bytes_retransmit=9 bytes_invalid=0 send_seq=181 receive_seq=181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997747 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1588 bytes_read=7840 bytes_retransmit=9 bytes_invalid=0 send_seq=180 receive_seq=180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000076 adj=63997573 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1173 bytes_read=10868 bytes_retransmit=9 bytes_invalid=0 send_seq=149 receive_seq=149 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999551 adj=47997654 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1838 bytes_read=5208 bytes_retransmit=9 bytes_invalid=0 send_seq=159 receive_seq=159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999921 adj=11999461 Octopus_Pro_H723_V1.1: temp=33.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=530 bytes_read=11072 bytes_retransmit=0 bytes_invalid=0 send_seq=87 receive_seq=87 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999948 adj=31998630 coil_temp=17.0 refs=0 mcu_temp=20.38 supply_voltage=3.012 th0: temp=45.6 th1: temp=45.7 th2: temp=50.0 th3: temp=49.2 sysload=0.76 cputime=658.239 memavail=7393100 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9100.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4706 bytes_read=10765 bytes_retransmit=9 bytes_invalid=0 send_seq=366 receive_seq=366 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015596 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1048 bytes_read=5223 bytes_retransmit=0 bytes_invalid=0 send_seq=146 receive_seq=146 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999297 adj=49997475 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1600 bytes_read=7970 bytes_retransmit=9 bytes_invalid=0 send_seq=182 receive_seq=182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997765 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1594 bytes_read=7954 bytes_retransmit=9 bytes_invalid=0 send_seq=181 receive_seq=181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000070 adj=63997653 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1179 bytes_read=11100 bytes_retransmit=9 bytes_invalid=0 send_seq=150 receive_seq=150 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999568 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1844 bytes_read=5224 bytes_retransmit=9 bytes_invalid=0 send_seq=160 receive_seq=160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999458 Octopus_Pro_H723_V1.1: temp=34.0 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=536 bytes_read=11428 bytes_retransmit=0 bytes_invalid=0 send_seq=88 receive_seq=88 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999947 adj=31998753 coil_temp=17.0 refs=0 mcu_temp=20.38 supply_voltage=3.012 th0: temp=45.5 th1: temp=45.8 th2: temp=50.0 th3: temp=49.2 sysload=0.76 cputime=658.283 memavail=7390056 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 9101.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4712 bytes_read=10897 bytes_retransmit=9 bytes_invalid=0 send_seq=367 receive_seq=367 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015577 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1054 bytes_read=5239 bytes_retransmit=0 bytes_invalid=0 send_seq=147 receive_seq=147 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999298 adj=49997473 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1606 bytes_read=8070 bytes_retransmit=9 bytes_invalid=0 send_seq=183 receive_seq=183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997787 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1600 bytes_read=8054 bytes_retransmit=9 bytes_invalid=0 send_seq=182 receive_seq=182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000071 adj=63997621 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1191 bytes_read=11348 bytes_retransmit=9 bytes_invalid=0 send_seq=152 receive_seq=152 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999575 adj=47997805 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1850 bytes_read=5251 bytes_retransmit=9 bytes_invalid=0 send_seq=161 receive_seq=161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999923 adj=11999456 Octopus_Pro_H723_V1.1: temp=33.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=542 bytes_read=11784 bytes_retransmit=0 bytes_invalid=0 send_seq=89 receive_seq=89 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999946 adj=31998752 coil_temp=17.0 refs=0 mcu_temp=20.38 supply_voltage=3.012 th0: temp=45.6 th1: temp=45.7 th2: temp=50.0 th3: temp=49.2 sysload=0.76 cputime=658.321 memavail=7390264 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.3 pwm=0.000 extruder1: target=0 temp=17.5 pwm=0.000
Stats 9102.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4718 bytes_read=11014 bytes_retransmit=9 bytes_invalid=0 send_seq=368 receive_seq=368 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015569 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1060 bytes_read=5268 bytes_retransmit=0 bytes_invalid=0 send_seq=148 receive_seq=148 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999296 adj=49997465 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1612 bytes_read=8198 bytes_retransmit=9 bytes_invalid=0 send_seq=184 receive_seq=184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997807 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1606 bytes_read=8182 bytes_retransmit=9 bytes_invalid=0 send_seq=183 receive_seq=183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000067 adj=63997636 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1197 bytes_read=11655 bytes_retransmit=9 bytes_invalid=0 send_seq=153 receive_seq=153 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999571 adj=47997846 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1856 bytes_read=5267 bytes_retransmit=9 bytes_invalid=0 send_seq=162 receive_seq=162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999923 adj=11999482 Octopus_Pro_H723_V1.1: temp=33.8 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=548 bytes_read=12140 bytes_retransmit=0 bytes_invalid=0 send_seq=90 receive_seq=90 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998739 coil_temp=17.0 refs=0 mcu_temp=20.39 supply_voltage=3.012 th0: temp=45.6 th1: temp=45.7 th2: temp=50.0 th3: temp=49.1 sysload=0.78 cputime=658.358 memavail=7390128 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.3 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9103.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4724 bytes_read=11117 bytes_retransmit=9 bytes_invalid=0 send_seq=369 receive_seq=369 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015568 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1072 bytes_read=5300 bytes_retransmit=0 bytes_invalid=0 send_seq=150 receive_seq=150 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999299 adj=49997432 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1618 bytes_read=8312 bytes_retransmit=9 bytes_invalid=0 send_seq=185 receive_seq=185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997777 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1612 bytes_read=8296 bytes_retransmit=9 bytes_invalid=0 send_seq=184 receive_seq=184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000066 adj=63997605 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1203 bytes_read=11887 bytes_retransmit=9 bytes_invalid=0 send_seq=154 receive_seq=154 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999575 adj=47997795 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1862 bytes_read=5283 bytes_retransmit=9 bytes_invalid=0 send_seq=163 receive_seq=163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999473 Octopus_Pro_H723_V1.1: temp=33.8 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=554 bytes_read=12496 bytes_retransmit=0 bytes_invalid=0 send_seq=91 receive_seq=91 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998693 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=45.5 th1: temp=45.7 th2: temp=50.1 th3: temp=49.1 sysload=0.78 cputime=658.400 memavail=7389600 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9104.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4730 bytes_read=11244 bytes_retransmit=9 bytes_invalid=0 send_seq=370 receive_seq=370 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015562 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1078 bytes_read=5316 bytes_retransmit=0 bytes_invalid=0 send_seq=151 receive_seq=151 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999307 adj=49997434 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1624 bytes_read=8412 bytes_retransmit=9 bytes_invalid=0 send_seq=186 receive_seq=186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000229 adj=63997778 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1618 bytes_read=8396 bytes_retransmit=9 bytes_invalid=0 send_seq=185 receive_seq=185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000065 adj=63997593 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1209 bytes_read=12119 bytes_retransmit=9 bytes_invalid=0 send_seq=155 receive_seq=155 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999572 adj=47997800 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1868 bytes_read=5299 bytes_retransmit=9 bytes_invalid=0 send_seq=164 receive_seq=164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999922 adj=11999464 Octopus_Pro_H723_V1.1: temp=33.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=560 bytes_read=12852 bytes_retransmit=0 bytes_invalid=0 send_seq=92 receive_seq=92 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998666 coil_temp=17.0 refs=0 mcu_temp=20.41 supply_voltage=3.012 th0: temp=45.4 th1: temp=45.6 th2: temp=50.0 th3: temp=49.1 sysload=0.78 cputime=658.444 memavail=7383492 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9105.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4736 bytes_read=11347 bytes_retransmit=9 bytes_invalid=0 send_seq=371 receive_seq=371 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015544 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1084 bytes_read=5332 bytes_retransmit=0 bytes_invalid=0 send_seq=152 receive_seq=152 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999307 adj=49997487 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1630 bytes_read=8526 bytes_retransmit=9 bytes_invalid=0 send_seq=187 receive_seq=187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997766 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1624 bytes_read=8510 bytes_retransmit=9 bytes_invalid=0 send_seq=186 receive_seq=186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997586 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1215 bytes_read=12411 bytes_retransmit=9 bytes_invalid=0 send_seq=156 receive_seq=156 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999568 adj=47997763 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1874 bytes_read=5315 bytes_retransmit=9 bytes_invalid=0 send_seq=165 receive_seq=165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999461 Octopus_Pro_H723_V1.1: temp=34.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=566 bytes_read=13208 bytes_retransmit=0 bytes_invalid=0 send_seq=93 receive_seq=93 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998669 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=45.5 th1: temp=45.7 th2: temp=49.9 th3: temp=49.0 sysload=0.78 cputime=658.488 memavail=7373084 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.5 pwm=0.000
Stats 9106.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4742 bytes_read=11450 bytes_retransmit=9 bytes_invalid=0 send_seq=372 receive_seq=372 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015559 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1090 bytes_read=5348 bytes_retransmit=0 bytes_invalid=0 send_seq=153 receive_seq=153 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999305 adj=49997470 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1636 bytes_read=8640 bytes_retransmit=9 bytes_invalid=0 send_seq=188 receive_seq=188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997761 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1630 bytes_read=8624 bytes_retransmit=9 bytes_invalid=0 send_seq=187 receive_seq=187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997582 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1221 bytes_read=12643 bytes_retransmit=9 bytes_invalid=0 send_seq=157 receive_seq=157 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999567 adj=47997729 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1880 bytes_read=5342 bytes_retransmit=9 bytes_invalid=0 send_seq=166 receive_seq=166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999920 adj=11999455 Octopus_Pro_H723_V1.1: temp=34.1 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=572 bytes_read=13564 bytes_retransmit=0 bytes_invalid=0 send_seq=94 receive_seq=94 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999936 adj=31998700 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=45.4 th1: temp=45.7 th2: temp=49.9 th3: temp=49.1 sysload=0.78 cputime=658.530 memavail=7368912 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.6 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9107.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4748 bytes_read=11596 bytes_retransmit=9 bytes_invalid=0 send_seq=373 receive_seq=373 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015567 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=1096 bytes_read=5377 bytes_retransmit=0 bytes_invalid=0 send_seq=154 receive_seq=154 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999306 adj=49997415 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1642 bytes_read=8754 bytes_retransmit=9 bytes_invalid=0 send_seq=189 receive_seq=189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997751 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1636 bytes_read=8738 bytes_retransmit=9 bytes_invalid=0 send_seq=188 receive_seq=188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997552 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1227 bytes_read=12890 bytes_retransmit=9 bytes_invalid=0 send_seq=158 receive_seq=158 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999564 adj=47997701 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1886 bytes_read=5358 bytes_retransmit=9 bytes_invalid=0 send_seq=167 receive_seq=167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999448 Octopus_Pro_H723_V1.1: temp=33.9 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=27.7  heater_bed: target=0 temp=16.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=578 bytes_read=13920 bytes_retransmit=0 bytes_invalid=0 send_seq=95 receive_seq=95 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998680 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=45.5 th1: temp=45.6 th2: temp=49.9 th3: temp=49.0 sysload=0.88 cputime=658.574 memavail=7379764 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9108.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4754 bytes_read=11699 bytes_retransmit=9 bytes_invalid=0 send_seq=374 receive_seq=374 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015578 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=1102 bytes_read=5393 bytes_retransmit=0 bytes_invalid=0 send_seq=155 receive_seq=155 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999309 adj=49997397 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1648 bytes_read=8868 bytes_retransmit=9 bytes_invalid=0 send_seq=190 receive_seq=190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997726 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1642 bytes_read=8852 bytes_retransmit=9 bytes_invalid=0 send_seq=189 receive_seq=189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997551 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1233 bytes_read=13182 bytes_retransmit=9 bytes_invalid=0 send_seq=159 receive_seq=159 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999561 adj=47997669 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1892 bytes_read=5374 bytes_retransmit=9 bytes_invalid=0 send_seq=168 receive_seq=168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999919 adj=11999438 Octopus_Pro_H723_V1.1: temp=33.8 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=584 bytes_read=14276 bytes_retransmit=0 bytes_invalid=0 send_seq=96 receive_seq=96 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998656 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=45.5 th1: temp=45.6 th2: temp=49.9 th3: temp=49.1 sysload=0.88 cputime=658.617 memavail=7366880 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.4 pwm=0.000
Stats 9109.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4760 bytes_read=11802 bytes_retransmit=9 bytes_invalid=0 send_seq=375 receive_seq=375 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015561 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=1108 bytes_read=5409 bytes_retransmit=0 bytes_invalid=0 send_seq=156 receive_seq=156 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999307 adj=49997400 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1654 bytes_read=8982 bytes_retransmit=9 bytes_invalid=0 send_seq=191 receive_seq=191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997708 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1648 bytes_read=8966 bytes_retransmit=9 bytes_invalid=0 send_seq=190 receive_seq=190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997521 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1239 bytes_read=13414 bytes_retransmit=9 bytes_invalid=0 send_seq=160 receive_seq=160 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997638 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1898 bytes_read=5390 bytes_retransmit=9 bytes_invalid=0 send_seq=169 receive_seq=169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999435 Octopus_Pro_H723_V1.1: temp=34.1 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=590 bytes_read=14632 bytes_retransmit=0 bytes_invalid=0 send_seq=97 receive_seq=97 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998669 coil_temp=17.0 refs=0 mcu_temp=20.41 supply_voltage=3.012 th0: temp=45.4 th1: temp=45.6 th2: temp=49.8 th3: temp=49.0 sysload=0.88 cputime=658.660 memavail=7372892 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.3 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 9110.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4766 bytes_read=11934 bytes_retransmit=9 bytes_invalid=0 send_seq=376 receive_seq=376 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015553 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=1114 bytes_read=5425 bytes_retransmit=0 bytes_invalid=0 send_seq=157 receive_seq=157 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999309 adj=49997394 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1660 bytes_read=9082 bytes_retransmit=9 bytes_invalid=0 send_seq=192 receive_seq=192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997726 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1654 bytes_read=9066 bytes_retransmit=9 bytes_invalid=0 send_seq=191 receive_seq=191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997530 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1245 bytes_read=13646 bytes_retransmit=9 bytes_invalid=0 send_seq=161 receive_seq=161 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999557 adj=47997640 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1904 bytes_read=5406 bytes_retransmit=9 bytes_invalid=0 send_seq=170 receive_seq=170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999440 Octopus_Pro_H723_V1.1: temp=34.0 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=596 bytes_read=14988 bytes_retransmit=0 bytes_invalid=0 send_seq=98 receive_seq=98 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998681 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=45.4 th1: temp=45.6 th2: temp=49.8 th3: temp=49.0 sysload=0.88 cputime=658.702 memavail=7367372 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9111.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4772 bytes_read=12037 bytes_retransmit=9 bytes_invalid=0 send_seq=377 receive_seq=377 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015537 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=1120 bytes_read=5441 bytes_retransmit=0 bytes_invalid=0 send_seq=158 receive_seq=158 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999308 adj=49997415 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1666 bytes_read=9196 bytes_retransmit=9 bytes_invalid=0 send_seq=193 receive_seq=193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997752 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1660 bytes_read=9180 bytes_retransmit=9 bytes_invalid=0 send_seq=192 receive_seq=192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997530 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1251 bytes_read=13938 bytes_retransmit=9 bytes_invalid=0 send_seq=162 receive_seq=162 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997658 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1910 bytes_read=5433 bytes_retransmit=9 bytes_invalid=0 send_seq=171 receive_seq=171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999439 Octopus_Pro_H723_V1.1: temp=34.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=602 bytes_read=15344 bytes_retransmit=0 bytes_invalid=0 send_seq=99 receive_seq=99 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998676 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=45.4 th1: temp=45.6 th2: temp=49.8 th3: temp=49.0 sysload=0.88 cputime=658.745 memavail=7372800 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.5 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9112.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4778 bytes_read=12154 bytes_retransmit=9 bytes_invalid=0 send_seq=378 receive_seq=378 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015526 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=1126 bytes_read=5470 bytes_retransmit=0 bytes_invalid=0 send_seq=159 receive_seq=159 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999308 adj=49997409 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1672 bytes_read=9324 bytes_retransmit=9 bytes_invalid=0 send_seq=194 receive_seq=194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997763 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1666 bytes_read=9308 bytes_retransmit=9 bytes_invalid=0 send_seq=193 receive_seq=193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000058 adj=63997606 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1257 bytes_read=14185 bytes_retransmit=9 bytes_invalid=0 send_seq=163 receive_seq=163 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999555 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1916 bytes_read=5449 bytes_retransmit=9 bytes_invalid=0 send_seq=172 receive_seq=172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999447 Octopus_Pro_H723_V1.1: temp=34.2 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=608 bytes_read=15700 bytes_retransmit=0 bytes_invalid=0 send_seq=100 receive_seq=100 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998698 coil_temp=17.0 refs=0 mcu_temp=20.39 supply_voltage=3.012 th0: temp=45.3 th1: temp=45.6 th2: temp=49.8 th3: temp=49.0 sysload=0.97 cputime=658.789 memavail=7373464 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9113.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4784 bytes_read=12286 bytes_retransmit=9 bytes_invalid=0 send_seq=379 receive_seq=379 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015515 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=1132 bytes_read=5486 bytes_retransmit=0 bytes_invalid=0 send_seq=160 receive_seq=160 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999313 adj=49997415 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1678 bytes_read=9424 bytes_retransmit=9 bytes_invalid=0 send_seq=195 receive_seq=195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997776 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1672 bytes_read=9408 bytes_retransmit=9 bytes_invalid=0 send_seq=194 receive_seq=194 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997604 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1263 bytes_read=14417 bytes_retransmit=9 bytes_invalid=0 send_seq=164 receive_seq=164 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1922 bytes_read=5465 bytes_retransmit=9 bytes_invalid=0 send_seq=173 receive_seq=173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999447 Octopus_Pro_H723_V1.1: temp=33.9 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=614 bytes_read=16056 bytes_retransmit=0 bytes_invalid=0 send_seq=101 receive_seq=101 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998697 coil_temp=17.0 refs=0 mcu_temp=20.38 supply_voltage=3.012 th0: temp=45.4 th1: temp=45.6 th2: temp=49.8 th3: temp=49.0 sysload=0.97 cputime=658.833 memavail=7373192 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 9114.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4790 bytes_read=12389 bytes_retransmit=9 bytes_invalid=0 send_seq=380 receive_seq=380 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015529 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=1138 bytes_read=5502 bytes_retransmit=0 bytes_invalid=0 send_seq=161 receive_seq=161 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999311 adj=49997460 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1684 bytes_read=9552 bytes_retransmit=9 bytes_invalid=0 send_seq=196 receive_seq=196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000230 adj=63997786 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1678 bytes_read=9536 bytes_retransmit=9 bytes_invalid=0 send_seq=195 receive_seq=195 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997612 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1269 bytes_read=14709 bytes_retransmit=9 bytes_invalid=0 send_seq=165 receive_seq=165 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997687 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1928 bytes_read=5481 bytes_retransmit=9 bytes_invalid=0 send_seq=174 receive_seq=174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999449 Octopus_Pro_H723_V1.1: temp=34.1 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=620 bytes_read=16412 bytes_retransmit=0 bytes_invalid=0 send_seq=102 receive_seq=102 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998774 coil_temp=17.0 refs=0 mcu_temp=20.38 supply_voltage=3.011 th0: temp=45.3 th1: temp=45.6 th2: temp=49.8 th3: temp=48.9 sysload=0.97 cputime=658.884 memavail=7380456 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.3 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 9115.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4796 bytes_read=12488 bytes_retransmit=9 bytes_invalid=0 send_seq=381 receive_seq=381 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015529 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=1144 bytes_read=5518 bytes_retransmit=0 bytes_invalid=0 send_seq=162 receive_seq=162 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999367 adj=49997410 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1690 bytes_read=9652 bytes_retransmit=9 bytes_invalid=0 send_seq=197 receive_seq=197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000233 adj=63997796 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1684 bytes_read=9636 bytes_retransmit=9 bytes_invalid=0 send_seq=196 receive_seq=196 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000062 adj=63997576 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1275 bytes_read=14941 bytes_retransmit=9 bytes_invalid=0 send_seq=166 receive_seq=166 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997662 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1934 bytes_read=5497 bytes_retransmit=9 bytes_invalid=0 send_seq=175 receive_seq=175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999446 Octopus_Pro_H723_V1.1: temp=34.1 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=626 bytes_read=16768 bytes_retransmit=0 bytes_invalid=0 send_seq=103 receive_seq=103 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999941 adj=31998747 coil_temp=17.0 refs=0 mcu_temp=20.38 supply_voltage=3.011 th0: temp=45.3 th1: temp=45.6 th2: temp=49.8 th3: temp=49.0 sysload=0.97 cputime=658.936 memavail=7380784 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9116.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4802 bytes_read=12620 bytes_retransmit=9 bytes_invalid=0 send_seq=382 receive_seq=382 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015525 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=1150 bytes_read=5534 bytes_retransmit=0 bytes_invalid=0 send_seq=163 receive_seq=163 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999379 adj=49997930 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1696 bytes_read=9752 bytes_retransmit=9 bytes_invalid=0 send_seq=198 receive_seq=198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000232 adj=63997812 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1690 bytes_read=9736 bytes_retransmit=9 bytes_invalid=0 send_seq=197 receive_seq=197 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997624 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000015 bytes_write=1281 bytes_read=15173 bytes_retransmit=9 bytes_invalid=0 send_seq=167 receive_seq=167 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999554 adj=47997665 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1940 bytes_read=5524 bytes_retransmit=9 bytes_invalid=0 send_seq=176 receive_seq=176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999457 Octopus_Pro_H723_V1.1: temp=34.0 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=632 bytes_read=17124 bytes_retransmit=0 bytes_invalid=0 send_seq=104 receive_seq=104 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998733 coil_temp=17.0 refs=0 mcu_temp=20.38 supply_voltage=3.011 th0: temp=45.3 th1: temp=45.5 th2: temp=49.7 th3: temp=48.9 sysload=0.97 cputime=658.982 memavail=7386752 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 9117.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4808 bytes_read=12737 bytes_retransmit=9 bytes_invalid=0 send_seq=383 receive_seq=383 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015520 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=1156 bytes_read=5563 bytes_retransmit=0 bytes_invalid=0 send_seq=164 receive_seq=164 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999371 adj=49997925 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1702 bytes_read=9894 bytes_retransmit=9 bytes_invalid=0 send_seq=199 receive_seq=199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000231 adj=63997798 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1696 bytes_read=9878 bytes_retransmit=9 bytes_invalid=0 send_seq=198 receive_seq=198 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000064 adj=63997642 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1287 bytes_read=15480 bytes_retransmit=9 bytes_invalid=0 send_seq=168 receive_seq=168 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999552 adj=47997693 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1946 bytes_read=5540 bytes_retransmit=9 bytes_invalid=0 send_seq=177 receive_seq=177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999918 adj=11999456 Octopus_Pro_H723_V1.1: temp=34.2 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.7 raspberry_pi: temp=30.2  heater_bed: target=0 temp=16.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=638 bytes_read=17480 bytes_retransmit=0 bytes_invalid=0 send_seq=105 receive_seq=105 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999945 adj=31998726 coil_temp=17.0 refs=0 mcu_temp=20.38 supply_voltage=3.011 th0: temp=45.3 th1: temp=45.5 th2: temp=49.7 th3: temp=48.9 sysload=1.13 cputime=659.028 memavail=7387336 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.3 pwm=0.000 extruder1: target=0 temp=17.8 pwm=0.000
Stats 9118.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4814 bytes_read=12840 bytes_retransmit=9 bytes_invalid=0 send_seq=384 receive_seq=384 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015530 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=1162 bytes_read=5579 bytes_retransmit=0 bytes_invalid=0 send_seq=165 receive_seq=165 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999359 adj=49997733 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1708 bytes_read=9994 bytes_retransmit=9 bytes_invalid=0 send_seq=200 receive_seq=200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000228 adj=63997777 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1702 bytes_read=9978 bytes_retransmit=9 bytes_invalid=0 send_seq=199 receive_seq=199 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000061 adj=63997632 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1293 bytes_read=15712 bytes_retransmit=9 bytes_invalid=0 send_seq=169 receive_seq=169 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999550 adj=47997681 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1952 bytes_read=5556 bytes_retransmit=9 bytes_invalid=0 send_seq=178 receive_seq=178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999460 Octopus_Pro_H723_V1.1: temp=34.0 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=644 bytes_read=17836 bytes_retransmit=0 bytes_invalid=0 send_seq=106 receive_seq=106 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999942 adj=31998770 coil_temp=17.0 refs=0 mcu_temp=20.38 supply_voltage=3.011 th0: temp=45.3 th1: temp=45.6 th2: temp=49.7 th3: temp=48.9 sysload=1.13 cputime=659.062 memavail=7395908 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.2 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9119.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4820 bytes_read=12972 bytes_retransmit=9 bytes_invalid=0 send_seq=385 receive_seq=385 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015550 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=1168 bytes_read=5595 bytes_retransmit=0 bytes_invalid=0 send_seq=166 receive_seq=166 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999349 adj=49997530 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1714 bytes_read=10094 bytes_retransmit=9 bytes_invalid=0 send_seq=201 receive_seq=201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997730 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1708 bytes_read=10078 bytes_retransmit=9 bytes_invalid=0 send_seq=200 receive_seq=200 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000059 adj=63997575 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1299 bytes_read=15944 bytes_retransmit=9 bytes_invalid=0 send_seq=170 receive_seq=170 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999548 adj=47997652 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1958 bytes_read=5572 bytes_retransmit=9 bytes_invalid=0 send_seq=179 receive_seq=179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999448 Octopus_Pro_H723_V1.1: temp=34.0 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.9 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=650 bytes_read=18176 bytes_retransmit=0 bytes_invalid=0 send_seq=107 receive_seq=107 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999940 adj=31998717 coil_temp=17.0 refs=0 mcu_temp=20.38 supply_voltage=3.011 th0: temp=45.3 th1: temp=45.4 th2: temp=49.7 th3: temp=48.8 sysload=1.13 cputime=659.093 memavail=7395684 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.3 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9120.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4826 bytes_read=13075 bytes_retransmit=9 bytes_invalid=0 send_seq=386 receive_seq=386 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015527 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=1174 bytes_read=5611 bytes_retransmit=0 bytes_invalid=0 send_seq=167 receive_seq=167 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999341 adj=49997370 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1720 bytes_read=10222 bytes_retransmit=9 bytes_invalid=0 send_seq=202 receive_seq=202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997676 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1714 bytes_read=10206 bytes_retransmit=9 bytes_invalid=0 send_seq=201 receive_seq=201 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000057 adj=63997520 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1305 bytes_read=16236 bytes_retransmit=9 bytes_invalid=0 send_seq=171 receive_seq=171 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999545 adj=47997612 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1964 bytes_read=5588 bytes_retransmit=9 bytes_invalid=0 send_seq=180 receive_seq=180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999437 Octopus_Pro_H723_V1.1: temp=34.0 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=656 bytes_read=18532 bytes_retransmit=0 bytes_invalid=0 send_seq=108 receive_seq=108 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999937 adj=31998670 coil_temp=17.0 refs=0 mcu_temp=20.38 supply_voltage=3.011 th0: temp=45.3 th1: temp=45.4 th2: temp=49.7 th3: temp=48.8 sysload=1.13 cputime=659.126 memavail=7395684 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.3 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9121.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4832 bytes_read=13178 bytes_retransmit=9 bytes_invalid=0 send_seq=387 receive_seq=387 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015512 rpi: mcu_awake=0.001 mcu_task_avg=0.000010 mcu_task_stddev=0.000009 bytes_write=1180 bytes_read=5627 bytes_retransmit=0 bytes_invalid=0 send_seq=168 receive_seq=168 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999331 adj=49997324 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1726 bytes_read=10322 bytes_retransmit=9 bytes_invalid=0 send_seq=203 receive_seq=203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997706 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1720 bytes_read=10306 bytes_retransmit=9 bytes_invalid=0 send_seq=202 receive_seq=202 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997553 dinghy: mcu_awake=0.006 mcu_task_avg=0.000020 mcu_task_stddev=0.000014 bytes_write=1311 bytes_read=16468 bytes_retransmit=9 bytes_invalid=0 send_seq=172 receive_seq=172 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999544 adj=47997633 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1970 bytes_read=5615 bytes_retransmit=9 bytes_invalid=0 send_seq=181 receive_seq=181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999451 Octopus_Pro_H723_V1.1: temp=33.9 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=662 bytes_read=18888 bytes_retransmit=0 bytes_invalid=0 send_seq=109 receive_seq=109 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999935 adj=31998741 coil_temp=17.0 refs=0 mcu_temp=20.39 supply_voltage=3.012 th0: temp=45.3 th1: temp=45.4 th2: temp=49.7 th3: temp=48.9 sysload=1.13 cputime=659.158 memavail=7395944 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.5 pwm=0.000 extruder1: target=0 temp=17.5 pwm=0.000
Stats 9122.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4838 bytes_read=13324 bytes_retransmit=9 bytes_invalid=0 send_seq=388 receive_seq=388 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015492 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1186 bytes_read=5656 bytes_retransmit=0 bytes_invalid=0 send_seq=169 receive_seq=169 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999324 adj=49997267 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1732 bytes_read=10436 bytes_retransmit=9 bytes_invalid=0 send_seq=204 receive_seq=204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997759 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1726 bytes_read=10420 bytes_retransmit=9 bytes_invalid=0 send_seq=203 receive_seq=203 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997562 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1317 bytes_read=16715 bytes_retransmit=9 bytes_invalid=0 send_seq=173 receive_seq=173 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999542 adj=47997650 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1976 bytes_read=5631 bytes_retransmit=9 bytes_invalid=0 send_seq=182 receive_seq=182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999917 adj=11999454 Octopus_Pro_H723_V1.1: temp=34.0 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=668 bytes_read=19244 bytes_retransmit=0 bytes_invalid=0 send_seq=110 receive_seq=110 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999934 adj=31998723 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=45.2 th1: temp=45.4 th2: temp=49.6 th3: temp=48.8 sysload=1.04 cputime=659.191 memavail=7395896 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.2 pwm=0.000 extruder1: target=0 temp=17.5 pwm=0.000
Stats 9123.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4844 bytes_read=13427 bytes_retransmit=9 bytes_invalid=0 send_seq=389 receive_seq=389 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015488 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1192 bytes_read=5672 bytes_retransmit=0 bytes_invalid=0 send_seq=170 receive_seq=170 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999317 adj=49997248 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1738 bytes_read=10564 bytes_retransmit=9 bytes_invalid=0 send_seq=205 receive_seq=205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997807 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1732 bytes_read=10548 bytes_retransmit=9 bytes_invalid=0 send_seq=204 receive_seq=204 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997599 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1323 bytes_read=17007 bytes_retransmit=9 bytes_invalid=0 send_seq=174 receive_seq=174 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999540 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1982 bytes_read=5647 bytes_retransmit=9 bytes_invalid=0 send_seq=183 receive_seq=183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999459 Octopus_Pro_H723_V1.1: temp=34.2 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=674 bytes_read=19600 bytes_retransmit=0 bytes_invalid=0 send_seq=111 receive_seq=111 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998718 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=45.3 th1: temp=45.4 th2: temp=49.6 th3: temp=48.9 sysload=1.04 cputime=659.225 memavail=7395896 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.3 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 9124.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4850 bytes_read=13530 bytes_retransmit=9 bytes_invalid=0 send_seq=390 receive_seq=390 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015477 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1198 bytes_read=5688 bytes_retransmit=0 bytes_invalid=0 send_seq=171 receive_seq=171 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999312 adj=49997217 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1744 bytes_read=10664 bytes_retransmit=9 bytes_invalid=0 send_seq=206 receive_seq=206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997798 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1738 bytes_read=10648 bytes_retransmit=9 bytes_invalid=0 send_seq=205 receive_seq=205 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000056 adj=63997595 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1329 bytes_read=17239 bytes_retransmit=9 bytes_invalid=0 send_seq=175 receive_seq=175 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997656 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1988 bytes_read=5663 bytes_retransmit=9 bytes_invalid=0 send_seq=184 receive_seq=184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999456 Octopus_Pro_H723_V1.1: temp=34.0 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=680 bytes_read=19956 bytes_retransmit=0 bytes_invalid=0 send_seq=112 receive_seq=112 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998696 coil_temp=17.0 refs=0 mcu_temp=20.40 supply_voltage=3.012 th0: temp=45.2 th1: temp=45.3 th2: temp=49.6 th3: temp=48.8 sysload=1.04 cputime=659.259 memavail=7395420 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.3 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9125.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4856 bytes_read=13662 bytes_retransmit=9 bytes_invalid=0 send_seq=391 receive_seq=391 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015470 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1204 bytes_read=5704 bytes_retransmit=0 bytes_invalid=0 send_seq=172 receive_seq=172 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999307 adj=49997214 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1750 bytes_read=10764 bytes_retransmit=9 bytes_invalid=0 send_seq=207 receive_seq=207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000223 adj=63997794 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1744 bytes_read=10748 bytes_retransmit=9 bytes_invalid=0 send_seq=206 receive_seq=206 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000055 adj=63997625 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1335 bytes_read=17471 bytes_retransmit=9 bytes_invalid=0 send_seq=176 receive_seq=176 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997669 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=1994 bytes_read=5679 bytes_retransmit=9 bytes_invalid=0 send_seq=185 receive_seq=185 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999455 Octopus_Pro_H723_V1.1: temp=34.1 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=686 bytes_read=20312 bytes_retransmit=0 bytes_invalid=0 send_seq=113 receive_seq=113 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999932 adj=31998689 coil_temp=17.0 refs=0 mcu_temp=20.39 supply_voltage=3.012 th0: temp=45.1 th1: temp=45.4 th2: temp=49.6 th3: temp=48.8 sysload=1.04 cputime=659.291 memavail=7395172 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9126.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4862 bytes_read=13761 bytes_retransmit=9 bytes_invalid=0 send_seq=392 receive_seq=392 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015478 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000009 bytes_write=1210 bytes_read=5720 bytes_retransmit=0 bytes_invalid=0 send_seq=173 receive_seq=173 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999304 adj=49997214 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1756 bytes_read=10892 bytes_retransmit=9 bytes_invalid=0 send_seq=208 receive_seq=208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997765 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1750 bytes_read=10876 bytes_retransmit=9 bytes_invalid=0 send_seq=207 receive_seq=207 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000054 adj=63997612 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1341 bytes_read=17763 bytes_retransmit=9 bytes_invalid=0 send_seq=177 receive_seq=177 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997671 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2000 bytes_read=5706 bytes_retransmit=9 bytes_invalid=0 send_seq=186 receive_seq=186 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999453 Octopus_Pro_H723_V1.1: temp=34.1 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=692 bytes_read=20668 bytes_retransmit=0 bytes_invalid=0 send_seq=114 receive_seq=114 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998708 coil_temp=17.0 refs=0 mcu_temp=20.38 supply_voltage=3.012 th0: temp=45.2 th1: temp=45.4 th2: temp=49.6 th3: temp=48.8 sysload=1.04 cputime=659.333 memavail=7395072 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 9127.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4868 bytes_read=13878 bytes_retransmit=9 bytes_invalid=0 send_seq=393 receive_seq=393 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015475 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1216 bytes_read=5749 bytes_retransmit=0 bytes_invalid=0 send_seq=174 receive_seq=174 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999302 adj=49997211 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1762 bytes_read=11004 bytes_retransmit=9 bytes_invalid=0 send_seq=209 receive_seq=209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000224 adj=63997754 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1756 bytes_read=10988 bytes_retransmit=9 bytes_invalid=0 send_seq=208 receive_seq=208 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997577 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1347 bytes_read=18010 bytes_retransmit=9 bytes_invalid=0 send_seq=178 receive_seq=178 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997663 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2006 bytes_read=5722 bytes_retransmit=9 bytes_invalid=0 send_seq=187 receive_seq=187 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999451 Octopus_Pro_H723_V1.1: temp=34.1 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=30.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=698 bytes_read=21024 bytes_retransmit=0 bytes_invalid=0 send_seq=115 receive_seq=115 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999929 adj=31998681 coil_temp=17.0 refs=0 mcu_temp=20.38 supply_voltage=3.012 th0: temp=45.2 th1: temp=45.3 th2: temp=49.5 th3: temp=48.8 sysload=1.04 cputime=659.438 memavail=7394736 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.3 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 9128.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4874 bytes_read=14010 bytes_retransmit=9 bytes_invalid=0 send_seq=394 receive_seq=394 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015490 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1222 bytes_read=5765 bytes_retransmit=0 bytes_invalid=0 send_seq=175 receive_seq=175 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999300 adj=49997231 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1768 bytes_read=11097 bytes_retransmit=9 bytes_invalid=0 send_seq=210 receive_seq=210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997759 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1762 bytes_read=11081 bytes_retransmit=9 bytes_invalid=0 send_seq=209 receive_seq=209 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997577 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1353 bytes_read=18242 bytes_retransmit=9 bytes_invalid=0 send_seq=179 receive_seq=179 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997661 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2012 bytes_read=5738 bytes_retransmit=9 bytes_invalid=0 send_seq=188 receive_seq=188 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999450 Octopus_Pro_H723_V1.1: temp=34.1 EBB42_Gen2_v1.0_T0: temp=29.9 EBB42_Gen2_v1.0_T1: temp=28.5 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=704 bytes_read=21380 bytes_retransmit=0 bytes_invalid=0 send_seq=116 receive_seq=116 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999933 adj=31998673 coil_temp=17.0 refs=0 mcu_temp=20.38 supply_voltage=3.012 th0: temp=45.1 th1: temp=45.3 th2: temp=49.6 th3: temp=48.7 sysload=1.04 cputime=659.491 memavail=7398192 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9129.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4880 bytes_read=14113 bytes_retransmit=9 bytes_invalid=0 send_seq=395 receive_seq=395 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015472 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1228 bytes_read=5781 bytes_retransmit=0 bytes_invalid=0 send_seq=176 receive_seq=176 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999295 adj=49997224 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1774 bytes_read=11216 bytes_retransmit=9 bytes_invalid=0 send_seq=211 receive_seq=211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000227 adj=63997750 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1768 bytes_read=11200 bytes_retransmit=9 bytes_invalid=0 send_seq=210 receive_seq=210 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997548 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1359 bytes_read=18534 bytes_retransmit=9 bytes_invalid=0 send_seq=180 receive_seq=180 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997667 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2018 bytes_read=5754 bytes_retransmit=9 bytes_invalid=0 send_seq=189 receive_seq=189 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999916 adj=11999453 Octopus_Pro_H723_V1.1: temp=34.3 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=710 bytes_read=21736 bytes_retransmit=0 bytes_invalid=0 send_seq=117 receive_seq=117 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998713 coil_temp=17.0 refs=0 mcu_temp=20.37 supply_voltage=3.012 th0: temp=45.2 th1: temp=45.4 th2: temp=49.5 th3: temp=48.7 sysload=1.04 cputime=659.526 memavail=7396204 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.3 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 9130.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4886 bytes_read=14216 bytes_retransmit=9 bytes_invalid=0 send_seq=396 receive_seq=396 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015466 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1234 bytes_read=5797 bytes_retransmit=0 bytes_invalid=0 send_seq=177 receive_seq=177 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999291 adj=49997223 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1780 bytes_read=11309 bytes_retransmit=9 bytes_invalid=0 send_seq=212 receive_seq=212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000226 adj=63997800 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1774 bytes_read=11293 bytes_retransmit=9 bytes_invalid=0 send_seq=211 receive_seq=211 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997578 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1365 bytes_read=18766 bytes_retransmit=9 bytes_invalid=0 send_seq=181 receive_seq=181 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999539 adj=47997680 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2024 bytes_read=5770 bytes_retransmit=9 bytes_invalid=0 send_seq=190 receive_seq=190 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999454 Octopus_Pro_H723_V1.1: temp=34.2 EBB42_Gen2_v1.0_T0: temp=30.0 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.7  heater_bed: target=0 temp=16.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=716 bytes_read=22092 bytes_retransmit=0 bytes_invalid=0 send_seq=118 receive_seq=118 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998705 coil_temp=17.0 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=45.1 th1: temp=45.4 th2: temp=49.5 th3: temp=48.6 sysload=1.04 cputime=659.561 memavail=7396208 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9131.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4892 bytes_read=14348 bytes_retransmit=9 bytes_invalid=0 send_seq=397 receive_seq=397 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015463 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000010 bytes_write=1240 bytes_read=5813 bytes_retransmit=0 bytes_invalid=0 send_seq=178 receive_seq=178 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999288 adj=49997228 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1786 bytes_read=11402 bytes_retransmit=9 bytes_invalid=0 send_seq=213 receive_seq=213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000225 adj=63997785 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000015 mcu_task_stddev=0.000009 bytes_write=1780 bytes_read=11386 bytes_retransmit=9 bytes_invalid=0 send_seq=212 receive_seq=212 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997584 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1371 bytes_read=18998 bytes_retransmit=9 bytes_invalid=0 send_seq=182 receive_seq=182 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999538 adj=47997702 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2030 bytes_read=5797 bytes_retransmit=9 bytes_invalid=0 send_seq=191 receive_seq=191 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999451 Octopus_Pro_H723_V1.1: temp=34.2 EBB42_Gen2_v1.0_T0: temp=30.2 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.2 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=722 bytes_read=22448 bytes_retransmit=0 bytes_invalid=0 send_seq=119 receive_seq=119 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998693 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=45.1 th1: temp=45.3 th2: temp=49.5 th3: temp=48.7 sysload=1.04 cputime=659.594 memavail=7396208 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.7 pwm=0.000
Stats 9132.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4898 bytes_read=14465 bytes_retransmit=9 bytes_invalid=0 send_seq=398 receive_seq=398 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015455 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1246 bytes_read=5842 bytes_retransmit=0 bytes_invalid=0 send_seq=179 receive_seq=179 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999286 adj=49997230 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1792 bytes_read=11544 bytes_retransmit=9 bytes_invalid=0 send_seq=214 receive_seq=214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000222 adj=63997767 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1786 bytes_read=11527 bytes_retransmit=9 bytes_invalid=0 send_seq=213 receive_seq=213 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000053 adj=63997600 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1377 bytes_read=19305 bytes_retransmit=9 bytes_invalid=0 send_seq=183 receive_seq=183 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999537 adj=47997693 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2036 bytes_read=5813 bytes_retransmit=9 bytes_invalid=0 send_seq=192 receive_seq=192 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999448 Octopus_Pro_H723_V1.1: temp=34.2 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.8 raspberry_pi: temp=29.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=728 bytes_read=22804 bytes_retransmit=0 bytes_invalid=0 send_seq=120 receive_seq=120 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999931 adj=31998709 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=45.1 th1: temp=45.3 th2: temp=49.5 th3: temp=48.6 sysload=1.03 cputime=659.628 memavail=7396204 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.2 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Stats 9133.9: gcodein=0  mcu: mcu_awake=0.000 mcu_task_avg=0.000001 mcu_task_stddev=0.000001 bytes_write=4904 bytes_read=14568 bytes_retransmit=9 bytes_invalid=0 send_seq=399 receive_seq=399 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=400015454 rpi: mcu_awake=0.001 mcu_task_avg=0.000009 mcu_task_stddev=0.000008 bytes_write=1252 bytes_read=5858 bytes_retransmit=0 bytes_invalid=0 send_seq=180 receive_seq=180 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=49999285 adj=49997247 toolboard_t0: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1798 bytes_read=11644 bytes_retransmit=9 bytes_invalid=0 send_seq=215 receive_seq=215 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000220 adj=63997743 toolboard_t1: mcu_awake=0.002 mcu_task_avg=0.000014 mcu_task_stddev=0.000009 bytes_write=1792 bytes_read=11627 bytes_retransmit=9 bytes_invalid=0 send_seq=214 receive_seq=214 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=64000052 adj=63997608 dinghy: mcu_awake=0.006 mcu_task_avg=0.000021 mcu_task_stddev=0.000014 bytes_write=1383 bytes_read=19537 bytes_retransmit=9 bytes_invalid=0 send_seq=184 receive_seq=184 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=47999536 adj=47997688 plasma: mcu_awake=0.000 mcu_task_avg=0.000004 mcu_task_stddev=0.000003 bytes_write=2042 bytes_read=5829 bytes_retransmit=9 bytes_invalid=0 send_seq=193 receive_seq=193 retransmit_seq=2 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=11999915 adj=11999449 Octopus_Pro_H723_V1.1: temp=34.3 EBB42_Gen2_v1.0_T0: temp=30.1 EBB42_Gen2_v1.0_T1: temp=28.6 raspberry_pi: temp=28.2  heater_bed: target=0 temp=16.3 pwm=0.000 beacon: mcu_awake=0.000 mcu_task_avg=0.000000 mcu_task_stddev=0.000000 bytes_write=734 bytes_read=23160 bytes_retransmit=0 bytes_invalid=0 send_seq=121 receive_seq=121 retransmit_seq=0 srtt=0.000 rttvar=0.000 rto=0.025 ready_bytes=0 upcoming_bytes=0 freq=31999930 adj=31998710 coil_temp=16.9 refs=0 mcu_temp=20.35 supply_voltage=3.012 th0: temp=45.0 th1: temp=45.2 th2: temp=49.5 th3: temp=48.6 sysload=1.03 cputime=659.661 memavail=7395208 print_time=12.676 buffer_time=0.000 print_stall=0 extruder: target=0 temp=18.4 pwm=0.000 extruder1: target=0 temp=17.6 pwm=0.000
Starting Klippy...
Args: ['/home/pi/klipper/klippy/klippy.py', '/home/pi/printer_data/config/printer.cfg', '-l', '/home/pi/printer_data/logs/klippy.log', '-I', '/home/pi/printer_data/comms/klippy.serial', '-a', '/home/pi/printer_data/comms/klippy.sock']
Git version: 'v0.12.0-268-g0844388d7-dirty'
Untracked files: klippy/extras/beacon.py, klippy/extras/beacon_adaptive_heat_soak.py, klippy/extras/beacon_mesh.py, klippy/extras/beacon_true_zero_correction.py, klippy/extras/beacon_user_z_offset.py, klippy/extras/fastconfig.py, klippy/extras/gcode_shell_command.py, klippy/extras/linear_movement_vibrations.py, klippy/extras/named_offsets.py, klippy/extras/ratos.py, (+4 files)
Branch: master
Remote: origin
Tracked URL: https://github.com/Klipper3d/klipper.git
CPU: 4 core ?
Python: '3.9.2 (default, Jan 24 2026, 09:41:14) \n[GCC 10.2.1 20210110]'
Start printer at Tue Mar 17 03:52:24 2026 (1773719544.4 9148.8)
===== Config file =====
[mcu rpi]
serial = /tmp/klipper_host_mcu

[board_pins btt-octopus-pro-h723-11]
aliases = 
	
	
	
	x_step_pin=PF13,
	x_dir_pin=PF12,
	x_enable_pin=PF14,
	x_uart_pin=PC4,
	x_diag_pin=PG6,
	x_endstop_pin=PG6,
	
	
	
	dual_carriage_step_pin=PF9,
	dual_carriage_dir_pin=PF10,
	dual_carriage_enable_pin=PG2,
	dual_carriage_uart_pin=PF2,
	dual_carriage_diag_pin=PG12,
	dual_carriage_endstop_pin=PG12,
	
	
	
	y_step_pin=PG0,
	y_dir_pin=PG1,
	y_enable_pin=PF15,
	y_uart_pin=PD11,
	y_diag_pin=PG9,
	y_endstop_pin=PG9,
	
	
	
	y1_step_pin=PG4,
	y1_dir_pin=PC1,
	y1_enable_pin=PA2,
	y1_uart_pin=PC7,
	y1_diag_pin=PG11,
	y1_endstop_pin=PG11,
	
	
	
	z0_step_pin=PC13,
	z0_dir_pin=PF0,
	z0_enable_pin=PF1,
	z0_uart_pin=PE4,
	z0_diag_pin=PG13,
	
	
	
	z1_step_pin=PE2,
	z1_dir_pin=PE3,
	z1_enable_pin=PD4,
	z1_uart_pin=PE1,
	z1_diag_pin=PG14,
	
	
	
	z2_step_pin=PE6,
	z2_dir_pin=PA14,
	z2_enable_pin=PE0,
	z2_uart_pin=PD3,
	z2_diag_pin=PG15,
	
	e_step_pin=PF11,
	e_dir_pin=PG3,
	e_enable_pin=PG5,
	e_uart_pin=PC6,
	
	e_heater_pin=PA2,
	e_sensor_pin=PF4,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=PA7,
	stepper_spi_miso_pin=PA6,
	stepper_spi_sclk_pin=PA5,
	adxl345_cs_pin=PA15,
	bltouch_sensor_pin=PB7,
	bltouch_control_pin=PB6,
	probe_pin=PB7,
	fan_part_cooling_pin=PA8,
	fan_toolhead_cooling_pin=PE5,
	fan_controller_board_pin=PD12,
	heater_bed_heating_pin=PA1,
	heater_bed_sensor_pin=PF3,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PG15,
	filament_sensor_motion_pin=PG14,
	ratrig_vaoc_probe_pin=PG10,
	ratrig_vaoc_led_pin=PB0,
	ratrig_vaoc_fan_pin=PD13,
	chamber_lighting_pin=PB11,
	chamber_filter_4p_fan_pin=PD14,
	chamber_filter_4p_fan_enable_pin=PD15

[mcu]
serial = /dev/RatOS/btt-octopus-pro-h723-11

[temperature_sensor Octopus_Pro_H723_V1.1]
sensor_type = temperature_mcu

[adxl345 controlboard]
cs_pin = PA15
spi_software_mosi_pin = PB5
spi_software_miso_pin = PB4
spi_software_sclk_pin = PB3

[board_pins toolboard_t0]
mcu = toolboard_t0
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t0]
serial = /dev/RatOS/btt-ebb42-gen2-10-t0

[temperature_sensor EBB42_Gen2_v1.0_T0]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t0

[lis2dw toolboard_t0]
axes_map = x, z, y
cs_pin = toolboard_t0:PB1
spi_software_mosi_pin = toolboard_t0:PB11
spi_software_miso_pin = toolboard_t0:PB2
spi_software_sclk_pin = toolboard_t0:PB10

[board_pins toolboard_t1]
mcu = toolboard_t1
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t1]
serial = /dev/RatOS/btt-ebb42-gen2-10-t1

[temperature_sensor EBB42_Gen2_v1.0_T1]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t1

[lis2dw toolboard_t1]
axes_map = x, z, y
cs_pin = toolboard_t1:PB1
spi_software_mosi_pin = toolboard_t1:PB11
spi_software_miso_pin = toolboard_t1:PB2
spi_software_sclk_pin = toolboard_t1:PB10

[gcode_macro RatOS]
variable_homing = "endstops"
variable_z_probe = "static"
variable_sensorless_x_current = 0.6
variable_sensorless_y_current = 0.9
variable_safe_home_x = "middle"
variable_safe_home_y = "middle"
variable_driver_type_x = "tmc2209"
variable_driver_type_y = "tmc2209"
variable_stowable_probe_stop_on_error = False
variable_chamber_filter_enable = True
variable_chamber_filter_speed = 0.5
variable_chamber_filter_disable_speed = 1.0
variable_chamber_filter_enable_at = "after_print_start"
variable_chamber_filter_disable_period = 300
variable_chamber_filter_disable_bed_temp = 0
variable_chamber_heater_enable = True
variable_chamber_heater_bed_temp = 115
variable_chamber_heater_preheating_temp = 150
variable_chamber_heater_heating_temp_offset = 25
variable_chamber_heater_control_external_heater = False
variable_chamber_heater_air_circulation_enable = True
variable_chamber_heater_air_circulation_fan_speed = 0.35
variable_chamber_heater_air_circulation_y_pos = 0
variable_chamber_heater_air_circulation_z_pos = 100
variable_chamber_heater_extra_fan_speed = 1.0
variable_chamber_heater_filter_fan_speed = 1.0
variable_bed_heat_soak_time = 0
variable_hotend_heat_soak_time = 0
variable_led_status_action = 0.0,1.0,1.0
variable_led_status_success = 0.0,1.0,0.0
variable_led_status_error = 1.0,0.0,1.0
variable_led_status_on = 1.0,1.0,1.0
variable_led_status_off = 0.0,0.0,1.0
variable_led_status_standby = 0.1,0.1,0.1
variable_led_status_heating = 1.0,0.0,0.0
variable_led_status_cooling = 0.0,0.0,1.0
variable_calibrate_bed_mesh = True
variable_adaptive_mesh = True
variable_start_print_park_in = "center"
variable_start_print_park_z_height = 3
variable_end_print_park_in = "back"
variable_pause_print_park_in = "back"
variable_end_print_park_z_hop = 20
variable_nozzle_priming = "primeblob"
variable_nozzle_prime_start_x = "max"
variable_nozzle_prime_start_y = "min"
variable_nozzle_prime_direction = "auto"
variable_nozzle_prime_bridge_fan = 102
variable_probe_for_priming_result = None
variable_probe_for_priming_end_result = None
variable_probe_for_priming_result_t1 = None
variable_probe_for_priming_end_result_t1 = None
variable_probe_for_priming_disable_mesh_constraints = False
variable_adaptive_prime_offset_threshold = -1.0
variable_last_z_offset = None
variable_runout_park_in = "front"
variable_enable_unload_tip_forming = False
variable_filament_unload_length = 150
description = RatOS variable storage macro, will echo variables to the console when run.
variable_relative_extrusion = True
variable_force_absolute_position = False
variable_preheat_extruder = True
variable_preheat_extruder_temp = 150
variable_macro_travel_speed = 600
variable_macro_travel_accel = 8000
variable_macro_z_speed = 15
variable_bed_margin_x = [59.6, 59.6]
variable_bed_margin_y = [14.35, 33.65]
variable_printable_x_min = 0
variable_printable_x_max = 0
variable_printable_y_min = 0
variable_printable_y_max = 0
variable_end_print_motors_off = True
variable_status_color_ok = "00FF00"
variable_status_color_error = "FF0000"
variable_status_color_unknown = "FFFF00"
variable_end_print_retract_filament = 10
gcode = 
	ECHO_RATOS_VARS
variable_auto_center_subject = False
variable_toolchange_zhop = 2.0
variable_toolchange_zspeed = 25
variable_toolchange_sync_fans = False
variable_toolchange_combined_zhop = False
variable_toolchange_travel_speed = 600
variable_toolchange_travel_accel = 8000
variable_toolchange_extrusion = 2.0
variable_toolchange_retraction = 2.0
variable_toolchange_feedrate = 7200
variable_toolchange_prepurging_timer = 0
variable_toolchange_standby_temp = -1
variable_toolchange_purge = 25
variable_toolchange_first_purge = 50
variable_beacon_bed_mesh_scv = 25
variable_beacon_contact_z_homing = False
variable_beacon_contact_start_print_true_zero = True
variable_beacon_contact_start_print_true_zero_fuzzy_position = True
variable_beacon_contact_calibrate_model_on_true_zero = True
variable_beacon_contact_wipe_before_true_zero = True
variable_beacon_contact_wipe_before_true_zero_method = "probe_clean"
variable_beacon_contact_true_zero_temp = 170
variable_beacon_contact_prime_probing = True
variable_beacon_contact_expansion_compensation = True
variable_beacon_contact_bed_mesh = False
variable_beacon_contact_bed_mesh_samples = 2
variable_beacon_contact_z_tilt_adjust = False
variable_beacon_contact_z_tilt_adjust_samples = 2
variable_beacon_scan_compensation_enable = True
variable_beacon_scan_compensation_profile = "auto"
variable_beacon_scan_compensation_desired_spacing = 10
variable_beacon_scan_compensation_bed_temp_mismatch_is_error = False
variable_beacon_contact_poke_bottom_limit = -1
variable_beacon_scan_method_automatic = False
variable_beacon_adaptive_heat_soak = True
variable_beacon_adaptive_heat_soak_max_wait = 5400
variable_beacon_adaptive_heat_soak_extra_wait_after_completion = 0
variable_beacon_adaptive_heat_soak_layer_quality = 3
variable_beacon_adaptive_heat_soak_maximum_first_layer_duration = 1800
variable_beacon_contact_start_print_true_zero_fuzzy_radius = 20
variable_homing_x = "endstop"
variable_homing_y = "endstop"
variable_default_toolhead = 0
variable_adxl_chip = ["lis2dw toolboard_t0", "lis2dw toolboard_t1"]
variable_shaper_x_freq = [54.2, 53.2, 53.6, 54.4]
variable_shaper_y_freq = [40.8, 47.6, 38.6, 38]
variable_shaper_x_type = ["mzv", "mzv", "mzv", "mzv"]
variable_shaper_y_type = ["mzv", "mzv", "mzv", "mzv"]
variable_x_driver_types = ["tmc5160"]
variable_x_axes = ["x"]
variable_y_driver_types = ["tmc5160", "tmc5160"]
variable_y_axes = ["y", "y1"]
variable_z_driver_types = ["tmc2209", "tmc2209", "tmc2209"]
variable_z_axes = ["z", "z1", "z2"]
variable_home_y_first = True

[ratos_homing]
axes = xyz
z_hop = 15
z_hop_speed = 15
gcode = 
	
	_LED_ON
	
	
	{% set prev_stop_on_error = printer["gcode_macro RatOS"].stowable_probe_stop_on_error %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set target_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	_IDEX_SINGLE
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE=True
	
	
	M400
	
	G90
	
	
	{% set X = true if params.X is defined else false %}
	{% set Y = true if params.Y is defined else false %}
	{% set Z = true if params.Z is defined else false %}
	{% if printer["gcode_macro RatOS"].home_y_first|default(false)|lower == 'true' %}
	HOME_Y X={X} Y={Y} Z={Z}
	HOME_X X={X} Y={Y} Z={Z}
	{% else %}
	HOME_X X={X} Y={Y} Z={Z}
	HOME_Y X={X} Y={Y} Z={Z}
	{% endif %}
	HOME_Z X={X} Y={Y} Z={Z}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE={prev_stop_on_error}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[gcode_macro HOME_X]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_x = printer["gcode_macro RatOS"].homing_x|lower %}
	{% set homing_x = homing_x if homing_x else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_X" MSG="printable_x_max: {printable_x_max}, safe_home_x: {safe_home_x}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}"
	
	
	{% if X or not Y and not Z %}
	{% if homing_x == 'endstop' %}
	G28 X
	{% elif homing_x == 'sensorless' %}
	{% if printer["dual_carriage"] is defined %}
	{ action_emergency_stop("sensorless homing not supported on IDEX!") }
	{% endif %}
	HOME_X_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_x to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_x, homing)) }
	{% endif %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1} MODE=PRIMARY
	G1 X{parking_position} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	{% endif %}
	{% set x_homed = True %}
	G0 X{safe_home_x} F{speed}
	M400
	{% endif %}

[gcode_macro HOME_Y]
gcode = 
	
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_y = printer["gcode_macro RatOS"].homing_y|lower %}
	{% set homing_y = homing_y if homing_y else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Y" MSG="printable_y_max: {printable_y_max}, safe_home_y: {safe_home_y}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}"
	
	
	{% if Y or not X and not Z %}
	{% if homing_y == 'endstop' %}
	G28 Y
	{% elif homing_y == 'sensorless' %}
	HOME_Y_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_y to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_y, homing)) }
	{% endif %}
	{% set y_homed = True %}
	G0 Y{safe_home_y} F{speed}
	{% endif %}

[gcode_macro HOME_Z]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	
	
	{% set beacon_contact_z_homing = true if printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_z_home_position_fuzzing_radius = printer["gcode_macro RatOS"].beacon_z_home_position_fuzzing_radius|default(0)|float %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Z" MSG="x_homed: {x_homed}, y_homed: {y_homed}, z_probe: {z_probe}, beacon_contact_z_homing: {beacon_contact_z_homing}"
	
	
	{% if Z or not Y and not X %}
	RATOS_ECHO MSG="Homing Z"
	{% if x_homed == False or y_homed == False %}
	{ action_emergency_stop("X and Y must be homed before homing Z") }
	{% else %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_homing %}
	{% if beacon_contact_start_print_true_zero %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% else %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	{% else %}
	G28 Z
	{% endif %}
	_Z_HOP
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro HOME_X_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	
	G4 P300
	
	G28 X
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"

[gcode_macro HOME_Y_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	
	G4 P300
	
	G28 Y
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"

[gcode_macro _Z_HOP]
description = Move Z axis up by Z_HOP distance at Z_HOP_SPEED. In relative mode it will move Z axis up by Z_HOP distance. In absolute mode it will move Z axis to Z_HOP distance.
gcode = 
	{% set z_hop = printer.fastconfig.config.ratos_homing.z_hop|float %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	G0 Z{z_hop} F{z_hop_speed}

[gcode_macro __MOVE_TO_SAFE_Z_HOME_ECHO_DEBUG]
gcode = 
	DEBUG_ECHO PREFIX="_MOVE_TO_SAFE_Z_HOME" MSG="x: {params.X}, y: {params.Y}, z_hop: {params.Z_HOP}, fuzzy_radius: {params.FUZZY_RADIUS}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}, printable_x_max: {printer['gcode_macro RatOS'].printable_x_max}, printable_y_max: {printer['gcode_macro RatOS'].printable_y_max}"

[gcode_macro MAYBE_HOME]
description = Only home unhomed axis. Specify ABL=1 to also ensure that automatic bed levelling is applied (if configured).
variable_is_kinematic_position_overriden = False
gcode = 
	{% set abl = params.ABL|default('')|lower in ('true', 'yes', '1') %}
	{% if printer["gcode_macro MAYBE_HOME"].is_kinematic_position_overriden|lower == 'true' %}
	RATOS_ECHO MSG="SET_CENTER_KINEMATIC_POSITION has been abused. Homing all axes. Please refrain from using SET_CENTER_KINEMATIC_POSITION outside of debugging purposes."
	G28
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=False
	{% else %}
	{% set axes = '' %}
	{% set isHomed = true %}
	{% set axesToHome = '' %}
	{% if params.X is defined %}
	{% set axes = axes ~ 'X ' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% endif %}
	{% if params.Y is defined %}
	{% set axes = axes ~ 'Y ' %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% endif %}
	{% if params.Z is defined %}
	{% set axes = axes ~ 'Z ' %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if params.X is not defined and params.Y is not defined and params.Z is not defined %}
	{% set axes = '' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if isHomed is false %}
	RATOS_ECHO MSG="Homing {axesToHome}"
	G28 {axesToHome}
	{% else %}
	RATOS_ECHO MSG="All requested axes already homed. Skipping homing."
	{% endif %}
	{% endif %}
	{% if abl %}
	{% if printer.z_tilt is defined %}
	{% if not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Performing Z tilt adjustment..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Z tilt already applied. Skipping Z tilt adjustment."
	{% endif %}
	{% elif printer.quad_gantry_level is defined %}
	{% if not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Performing quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Quad gantry leveling already applied. Skipping quad gantry leveling."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="No automatic bed leveling method configured. Skipping bed leveling."
	{% endif %}
	{% endif %}

[gcode_macro PID_CALIBRATE_HOTEND]
description = Perform a PID calibration test for a given extruder heater.
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set temp = params.TEMP|default(220)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_HOTEND" MSG="TEMP={temp}"
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO MSG="PID calibration hotend heater T0 at {temp}°C..."
	PID_CALIBRATE HEATER=extruder TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	
	{% if toolhead==0 or toolhead==1 %}
	RATOS_ECHO MSG="PID calibration hotend heater T{toolhead} at {temp}°C..."
	PID_CALIBRATE HEATER=extruder{'' if toolhead==0 else toolhead} TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_BED]
description = Perform a PID calibration test for the bed heater.
gcode = 
	
	{% set temp = params.TEMP|default(80)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_BED" MSG="TEMP={temp}"
	RATOS_ECHO MSG="PID calibration bed heater at {temp}°C..."
	
	
	PID_CALIBRATE HEATER=heater_bed TARGET={temp}
	
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_CHAMBER_HEATER]
description = Perform a PID calibration test for the chamber heater.
gcode = 
	
	{% set temp = params.TEMP|default(150)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_CHAMBER_HEATER" MSG="TEMP={temp}"
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	RATOS_ECHO MSG="PID calibration chamber heater at {temp}°C..."
	PID_CALIBRATE HEATER=chamber_heater TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_heater" %}
	{% set link_text = "RatOS Chamber Heater" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber heater found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro INITIALIZE_PA_TUNING]
description = Start a pressure advance tuning tower.
gcode = 
	
	{% set start = params.START|default(0.0)|float %}
	{% set factor = params.FACTOR|default(0.001)|float %}
	
	
	{% set layer_number = printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|default(0)|int %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if is_printing_gcode and layer_number < 2 %}
	DEBUG_ECHO PREFIX="START_PA_TOWER" MSG="START: {start}, FACTOR: {factor}"
	RATOS_ECHO MSG="Starting pressure advance tuning tower..."
	TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START={start} FACTOR={factor}
	{% else %}
	RATOS_ECHO MSG="Pressure advance tuning tower requires you to be printing gcode and on layer 1 to start."
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro CHAMBER_FILTER_ON]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	_CHAMBER_FILTER_TURN_ON
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro CHAMBER_FILTER_OFF]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Deactivating chamber filter..."
	_CHAMBER_FILTER_TURN_OFF
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set chamber_filter_enable_at = printer["gcode_macro RatOS"].chamber_filter_enable_at|default('after_print_start')|lower %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_ON" MSG="at: {at}, chamber_filter_enable: {chamber_filter_enable}, chamber_filter_enable_at: {chamber_filter_enable_at}, chamber_filter_speed: {chamber_filter_speed}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	{% if chamber_filter_enable_at == at %}
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	
	
	_CHAMBER_FILTER_TURN_ON AT={at}
	
	
	{% if chamber_filter_enable_at == "print_end" %}
	_LED_CHAMBER_FILTER_ON
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_OFF]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF" MSG="chamber_filter_enable: {chamber_filter_enable}, filter_disable_period: {filter_disable_period}, filter_disable_bed_temp: {filter_disable_bed_temp}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	
	{% if filter_disable_period > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting {filter_disable_period} seconds before turning chamber filter off..."
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION={filter_disable_period}
	{% endif %}
	
	
	{% if filter_disable_bed_temp > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting for bed temp to cool down to {filter_disable_bed_temp}°C to turn filter off..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM=0 MAXIMUM={filter_disable_bed_temp}
	_CHAMBER_FILTER_TURN_OFF
	_LED_CHAMBER_FILTER_OFF
	{% endif %}
	
	{% endif %}

[delayed_gcode _CHAMBER_FILTER_OFF_TIMER]
gcode = 
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF_TIMER" MSG="executed"
	
	
	_CHAMBER_FILTER_TURN_OFF
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Chamber filter turned off!"
	
	
	_LED_CHAMBER_FILTER_OFF

[gcode_macro _CHAMBER_FILTER_TURN_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_speed|default(0)|float %}
	{% if at == "print_end" %}
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_disable_speed|default(0)|float %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION=0
	
	
	SET_FAN_SPEED FAN=filter SPEED={chamber_filter_speed}

[gcode_macro _CHAMBER_FILTER_TURN_OFF]
gcode = 
	
	SET_FAN_SPEED FAN=filter SPEED=0

[gcode_macro _CHAMBER_FILTER_SANITY_CHECK]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	{% if filter_disable_bed_temp > 0 and filter_disable_period > 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable, not both.")}
	{% endif %}
	
	{% if filter_disable_bed_temp == 0 and filter_disable_period == 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable.")}
	{% endif %}
	
	{% endif %}

[gcode_macro CHAMBER_HEATER_ON]
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(45)|int %}
	
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp} IS_FROM_START_PRINT=False

[gcode_macro CHAMBER_HEATER_OFF]
gcode = 
	_CHAMBER_HEATER_OFF

[gcode_macro _CHAMBER_HEATER_ON]
variable_chamber_temp = 0
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	{% set is_from_start_print = true if params.IS_FROM_START_PRINT|default(True)|lower == 'true' else false %}
	
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set chamber_heater_enable = true if printer["gcode_macro RatOS"].chamber_heater_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}
	{% set chamber_heater_preheating_temp = printer["gcode_macro RatOS"].chamber_heater_preheating_temp|default(150)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	{% set chamber_heater_control_external_heater = true if printer["gcode_macro RatOS"].chamber_heater_control_external_heater|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_enable = true if printer["gcode_macro RatOS"].chamber_heater_air_circulation_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_fan_speed = printer["gcode_macro RatOS"].chamber_heater_air_circulation_fan_speed|default(0.35)|float %}
	{% set chamber_heater_air_circulation_y_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_y_pos|default(0)|float %}
	{% set chamber_heater_air_circulation_z_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_z_pos|default(100)|float %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_HEATER_ON" MSG="chamber_heater_enable: {chamber_heater_enable}, chamber_heater_preheating_temp: {chamber_heater_preheating_temp}, chamber_heater_heating_temp_offset: {chamber_heater_heating_temp_offset}, bed_temp: {bed_temp}, chamber_temp: {chamber_temp}, start_chamber_temp: {start_chamber_temp}"
	
	
	{% if chamber_heater_enable and chamber_temp > 0 and chamber_heater_bed_temp > 0 %}
	
	
	_LED_HEATING
	
	
	RATOS_ECHO MSG="Preheating chamber to {(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}°C..."
	
	
	{% set chamber_temp_sensor = "extruder" %}
	{% if printer["dual_carriage"] is defined and default_toolhead == 1 %}
	{% set chamber_temp_sensor = "extruder1" %}
	{% endif %}
	{% if printer["temperature_sensor chamber"] is defined %}
	{% set chamber_temp_sensor = "temperature_sensor chamber" %}
	{% endif %}
	
	
	{% set current_chamber_temp = printer['%s' % chamber_temp_sensor].temperature|int %}
	
	
	{% set needs_heating = current_chamber_temp < (start_chamber_temp if start_chamber_temp > 0 else chamber_temp) %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_BEFORE_PREHEATING
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	{% if not is_from_start_print %}
	MAYBE_HOME
	{% endif %}
	G0 Z{chamber_heater_air_circulation_z_pos} F{z_speed}
	G0 Y{chamber_heater_air_circulation_y_pos} F{speed}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * chamber_heater_air_circulation_fan_speed)}
	{% endif %}
	{% else %}
	{% if is_from_start_print %}
	G0 Z{z} F{z_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE={chamber_temp}
	
	
	{% if needs_heating %}
	
	
	M140 S{chamber_heater_bed_temp}
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={chamber_heater_preheating_temp}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	
	{% endif %}
	
	
	{% if needs_heating %}
	_CHAMBER_HEATER_EXTRA_FAN_ON
	{% endif %}
	
	
	{% if needs_heating %}
	TEMPERATURE_WAIT SENSOR="{chamber_temp_sensor}" MINIMUM={(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% endif %}
	
	
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED=0
	_CHAMBER_FILTER_ON AT="before_print_start"
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	G28 Z
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_AFTER_PREHEATING
	{% endif %}
	
	
	{% if printer["temperature_sensor chamber"] is defined %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined and chamber_heater_control_external_heater %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	
	
	_LED_SUCCESS
	
	{% endif %}

[gcode_macro _CHAMBER_HEATER_OFF]
gcode = 
	RATOS_ECHO MSG="Deactivating chamber heater..."
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=0
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE=0
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	
	
	_CHAMBER_HEATER_EXTRA_FAN_OFF

[delayed_gcode _CHAMBER_HEATER_CONTROL]
initial_duration = 0.
gcode = 
	
	{% set chamber_temp = printer["gcode_macro _CHAMBER_HEATER_ON"].chamber_temp|default(0)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	
	
	{% set current_chamber_temp = printer['temperature_sensor chamber'].temperature|int %}
	
	
	{% if current_chamber_temp < chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	{% endif %}
	
	
	{% if current_chamber_temp >= chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_ON]
gcode = 
	
	{% set chamber_heater_extra_fan_speed = printer["gcode_macro RatOS"].chamber_heater_extra_fan_speed|default(0.0)|float %}
	
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	{% if chamber_heater_extra_fan_speed > 0 %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED={chamber_heater_extra_fan_speed}
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_OFF]
gcode = 
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED=0
	{% endif %}

[gcode_macro _USER_CHAMBER_HEATER_BEFORE_PREHEATING]
description = Will be executed before chamber preheating, only if heating is needed.
gcode = 

[gcode_macro _USER_CHAMBER_HEATER_AFTER_PREHEATING]
description = Will be executed after chamber preheating, only if heating was needed.
gcode = 

[gcode_macro RESET_HEATSOAK_SETTINGS]
description = Resets all heatsoak-related settings to startup defaults
gcode = 
	HEATSOAK_SETTINGS ACTION=reset

[gcode_macro USE_ADAPTIVE_HEATSOAK]
description = Temporarily enables adaptive bed heatsoaking (if a beacon probe is present), will reset to printer.cfg settings
	when Klipper is restarted. Optionally specify QUALITY (1-5) and maximum FIRST_LAYER_DURATION (in minutes).
	Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.QUALITY|default("1..5") %}
	{% set _ = params.FIRST_LAYER_DURATION|default("1..120 minutes") %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("Adaptive heatsoaking is only available when a beacon probe is configured.") }
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_quality = (settings.variable_beacon_adaptive_heat_soak_layer_quality if defsrc == 'startup' else current.beacon_adaptive_heat_soak_layer_quality)|default(3)|int %}
	{% set default_first_layer_duration_secs = (settings.variable_beacon_adaptive_heat_soak_maximum_first_layer_duration if defsrc == 'startup' else current.beacon_adaptive_heat_soak_maximum_first_layer_duration)|default(1800)|int %}
	{% if params2.QUALITY is defined %}
	{% set quality = params2.QUALITY|int %}
	{% if quality < 1 or quality > 5 %}
	{ action_raise_error("QUALITY must be between 1 (rough) and 5 (maximum). Use 3 (normal) if unsure.") }
	{% endif %}
	{% else %}
	{% set quality = default_quality %}
	{% endif %}
	{% if params2.FIRST_LAYER_DURATION is defined %}
	{% set first_layer_duration_mins = params2.FIRST_LAYER_DURATION|float %}
	{% if first_layer_duration_mins <= 0 %}
	{ action_raise_error("FIRST_LAYER_DURATION must be a positive number specifying the maximum first layer duration in minutes.") }
	{% endif %}
	{% if first_layer_duration_mins > 120 %}
	CONSOLE_ECHO MSG="FIRST_LAYER_DURATION will be limited to 120 minutes. Values larger than this will not have an effect on soak time."
	{% set first_layer_duration_mins = 120 %}
	{% endif %}
	{% set first_layer_duration_secs = (first_layer_duration_mins * 60.0)|int %}
	{% else %}
	{% set first_layer_duration_secs = default_first_layer_duration_secs %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	{% endif %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=True beacon_adaptive_heat_soak_layer_quality={quality} beacon_adaptive_heat_soak_maximum_first_layer_duration={first_layer_duration_secs}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."

[gcode_macro USE_FIXED_HEATSOAK]
description = Temporarily enables fixed bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
	Optionally specify DURATION (in minutes). Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.DURATION|default("0..720 minutes") %}
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_duration = (settings.variable_bed_heat_soak_time if defsrc == 'startup' else current.bed_heat_soak_time)|default(0)|int %}
	{% if params2.DURATION is defined %}
	{% set duration_mins = params2.DURATION|float %}
	{% if duration_mins < 0 %}
	{ action_raise_error("DURATION must be a non-negative number specifying the heatsoak duration in minutes.") }
	{% endif %}
	{% if duration_mins > 720 %}
	CONSOLE_ECHO MSG="DURATION will be limited to 720 minutes (12 hours). If you really need a larger value, adjust printer.cfg instead."
	{% set duration_mins = 720 %}
	{% endif %}
	{% set duration_secs = (duration_mins * 60.0)|int %}
	{% else %}
	{% set duration_secs = default_duration %}
	{% set duration_mins = duration_secs / 60.0 %}
	{% endif %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% if has_beacon %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=False bed_heat_soak_time={duration_secs}
	{% else %}
	HEATSOAK_SETTINGS QUIET=1 bed_heat_soak_time={duration_secs}
	{% endif %}
	{% if duration_mins < 1e-3 %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% else %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% endif %}

[gcode_macro USE_NO_HEATSOAK]
description = Temporarily disables bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
gcode = 
	USE_FIXED_HEATSOAK DURATION=0

[gcode_macro HEATSOAK_SETTINGS]
description = Shows or adjusts heatsoak settings
	- With no arguments: shows current heatsoak settings, specify VERBOSE=1 for detailed output
	- With arguments: sets the specified settings. Use the full setting name without the variable_ prefix, e.g. bed_heat_soak_time=300 or beacon_adaptive_heat_soak_layer_quality=4. See printer.cfg for available settings.
variable_default_source = "startup"
gcode = 
	
	{% set params2 = params %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% set quiet = params2.pop("QUIET", None)|default("0") in ("1", "true", "yes") %}
	{% set verbose = params2.pop("VERBOSE", None)|default("0") in ("1", "true", "yes") %}
	{% if has_beacon %}
	{% set vars = (
	"beacon_adaptive_heat_soak",
	"beacon_adaptive_heat_soak_max_wait",
	"beacon_adaptive_heat_soak_extra_wait_after_completion",
	"beacon_adaptive_heat_soak_layer_quality",
	"beacon_adaptive_heat_soak_maximum_first_layer_duration",
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% else %}
	{% set vars = (
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% endif %}
	{% set action = "show" if params|length == 0 else params2.ACTION %}
	{% if action is defined and params|length > 1 %}
	{ action_raise_error("ACTION cannot be specified with other parameters.") }
	{% elif action is not defined %}
	{% for k, v in params2.items() %}
	{% set k = k|lower %}
	{% if k in vars %}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Setting {k} to {v}"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={k} VALUE={v}
	{% else %}
	{ action_raise_error("Parameter '%s' is not recognised. Note that adaptive heatsoaking settings can only be set when a beacon probe is configured." % k) }
	{% endif %}
	{% endfor %}
	{% elif action == "reset" %}
	_RESET_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	CONSOLE_ECHO MSG="Heatsoak settings have been reset to their original values."
	{% elif action == "show" %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% set is_adaptive = False if not has_beacon else current.beacon_adaptive_heat_soak|default("")|lower == "true" %}
	{% if is_adaptive %}
	{% set quality = current.beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set first_layer_duration_secs = current.beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."
	{% elif current.bed_heat_soak_time|default(0)|int > 0 %}
	{% set duration_mins = (current.bed_heat_soak_time|int / 60.0) %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% else %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% endif %}
	{% if verbose %}
	CONSOLE_ECHO MSG="Detailed settings:"
	_SHOW_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	{% endif %}
	{% else %}
	{ action_raise_error("Action '%s' is not recognised" % action) }
	{% endif %}

[gcode_macro _LED_START_PRINTING]
gcode = 
	_LED_ACTION

[gcode_macro _LED_START_PRINTING_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_PRINTING]
gcode = 
	_LED_ON TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_PAUSE]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_ON]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_OFF]
gcode = 
	_LED_STANDBY

[gcode_macro _LED_LOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_LOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_RUNOUT]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_CLOG]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_UNLOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_UNLOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_DEACTIVATE_TOOLHEAD]
gcode = 
	_LED_OFF TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_STANDBY]
gcode = 
	_LED_STANDBY TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_WAKEUP]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_MOTORS_OFF]
gcode = 
	_LED_STANDBY
	_LED_VAOC_OFF

[gcode_macro _LED_INPUT_SHAPER_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_INPUT_SHAPER_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_BEACON_CALIBRATION_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_VAOC_ON]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=1.0 GREEN=1.0 BLUE=1.0
	{% endif %}

[gcode_macro _LED_VAOC_OFF]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=0.0 GREEN=0.0 BLUE=0.0
	{% endif %}

[gcode_macro _LED_ACTION]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_action %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SUCCESS]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_success %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_HEATING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_heating %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_COOLING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_cooling %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ERROR]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_error %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ON]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_on %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_OFF]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_off %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_STANDBY]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_standby %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}
	
	{% if toolhead >= 0 %}
	{% if printer['neopixel nozzle_led_t%s' % toolhead] is defined  %}
	SET_LED LED={'nozzle_led_t%s' % toolhead} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% else %}
	{% if printer['neopixel nozzle_led_t0'] is defined  %}
	SET_LED LED={'nozzle_led_t0'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% if printer['neopixel nozzle_led_t1'] is defined %}
	SET_LED LED={'nozzle_led_t1'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% endif %}
	
	_USER_LED_SET { rawparams }

[gcode_macro _USER_LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}

[gcode_macro LOAD_FILAMENT]
description = Loads new filament. Note: be careful with PETG, make sure you inspect the tip of your filament before loading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% if filament_name == '' or filament_type == '' %}
	{% set filament_name = 'unknown' %}
	{% set filament_type = 'unknown' %}
	{% endif %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_LOAD_FILAMENT TEMP={temp} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_LOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_LOAD_FILAMENT]
description = Load filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_LOAD_FILAMENT" MSG="TEMP={temp}"
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=load_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	_LOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	
	
	RESTORE_GCODE_STATE NAME=load_state
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament load routine complete, please check that the filament was loaded correctly."

[gcode_macro _IDEX_LOAD_FILAMENT]
description = Load filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament into T{toolhead}..."
	
	DEBUG_ECHO PREFIX="_IDEX_LOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	_LOAD_FILAMENT TOOLHEAD={toolhead} TEMP={temp} AUTOMATED={automated}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="Filament load routine for T{toolhead} complete, please check that the filament was loaded correctly."

[gcode_macro _LOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default(false)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE TOOLHEAD={toolhead}
	_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into hotend.."
	G92 E0
	G0 E{extruder_gear_to_cooling_position_distance} F{extruder_load_speed}
	G92 E0
	M400
	RATOS_ECHO MSG="Filament loaded into hotend."

[gcode_macro _LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set load_speed = printer["gcode_macro T%s" % toolhead].filament_load_speed|float * 60 %}
	{% set filament_loading_nozzle_offset = printer["gcode_macro T%s" % toolhead].filament_loading_nozzle_offset|float %}
	{% set cooling_position_to_nozzle_distance = printer["gcode_macro T%s" % toolhead].cooling_position_to_nozzle_distance|float %}
	{% set purge_after_load = printer["gcode_macro T%s" % toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into nozzle... Please wait!"
	G92 E0
	
	G0 E{cooling_position_to_nozzle_distance + filament_loading_nozzle_offset} F{load_speed}
	G92 E0
	G4 P1000
	_PURGE_FILAMENT	TOOLHEAD={toolhead} E={purge_after_load}
	RATOS_ECHO MSG="Filament loaded into nozzle!"

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"
	
	
	{% set filament_grabbing_length = printer["gcode_macro T%s" % toolhead].filament_grabbing_length|float %}
	{% set filament_grabbing_speed = printer["gcode_macro T%s" % toolhead].filament_grabbing_speed|float %}
	{% set resume_after_insert = true if printer["gcode_macro T%s" % toolhead].resume_after_insert|default(true)|lower == 'true' else false %}
	{% set enable_insert_detection = true if printer["gcode_macro T%s" % toolhead].enable_insert_detection|default(true)|lower == 'true' else false %}
	
	
	{% set current_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	
	{% if enable_insert_detection %}
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="toolhead: {toolhead}, filament_grabbing_length: {filament_grabbing_length}, filament_grabbing_speed: {filament_grabbing_speed}, current_idex_mode: {current_idex_mode}"
	
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	RATOS_ECHO MSG="Filament inserted into T{toolhead}, loading..."
	
	
	FORCE_MOVE STEPPER={'extruder%s' % ('' if toolhead == 0 else toolhead)} DISTANCE={filament_grabbing_length} VELOCITY={filament_grabbing_speed}
	M400
	
	
	{% if printer.pause_resume.is_paused %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% if resume_after_insert %}
	RESUME
	{% endif %}
	{% else %}
	{% if not printer.virtual_sdcard.is_active %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"

[gcode_macro _PURGE_BEFORE_UNLOAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set purge_before_unload = printer["gcode_macro T%s" % toolhead].purge_before_unload|float %}
	
	DEBUG_ECHO PREFIX="_PURGE_BEFORE_UNLOAD" MSG="TOOLHEAD: {toolhead}"
	
	
	{% if purge_before_unload > 0 %}
	G92 E0
	G0 E{purge_before_unload} F300
	G92 E0
	M400
	{% endif %}

[gcode_macro _PURGE_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set e = params.E|int %}
	{% set r = params.R|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_PURGE_FILAMENT" MSG="TOOLHEAD: {toolhead}, E: {e}"
	
	
	{% if e > 0 %}
	
	
	G92 E0
	G0 E{e} F300
	G92 E0
	M400
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={0.4 if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={0.4 if toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * 0.4)}
	{% endif %}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if r > 0 %}
	G92 E0
	G0 E-{r} F300
	G92 E0
	M400
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro _MOVE_TO_LOADING_POSITION]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_MOVE_TO_LOADING_POSITION" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	
	G1 X{loading_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _CLEANING_MOVE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_CLEANING_MOVE" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].parking_position is defined and printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set parking_position = printer["gcode_macro T%s" % toolhead].parking_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	{% set cleaning_position = loading_position %}
	{% if loading_position == parking_position %}
	{% if loading_position > 0 %}
	{% set cleaning_position = loading_position - 30 %}
	{% else %}
	{% set cleaning_position = loading_position + 30 %}
	{% endif %}
	{% endif %}
	
	
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _BED_MESH_SANITY_CHECK]
gcode = 
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is defined %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_start_print_true_zero_fuzzy_position %}
	CONSOLE_ECHO TYPE="error" TITLE="Defined zero reference not compatible with fuzzy true zero" MSG="Using fuzzy start print true zero position is not compatible with a defined zero_reference_position value in the [bed_mesh] section in printer.cfg._N_Please remove the zero_reference_position value from the [bed_mesh] section, or disable fuzzy true zero position in printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_start_print_true_zero_fuzzy_position: False"
	_STOP_AND_RAISE_ERROR MSG="Defined zero reference not compatible with fuzzy true zero"
	{% elif zero_ref_pos[0]|float|round != safe_home_x|float|round or zero_ref_pos[1]|float|round != safe_home_y|float|round %}
	CONSOLE_ECHO TYPE="error" TITLE="Zero reference position does not match safe home position" MSG="Please update your bed mesh zero reference position in printer.cfg, like so:_N__N_[bed_mesh]_N_zero_reference_position: {safe_home_x|float|round},{safe_home_y|float|round}_N_"
	_STOP_AND_RAISE_ERROR MSG="Zero reference position does not match safe home position"
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_bed_mesh %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact bed mesh is enabled" MSG="Beacon contact bed mesh is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_bed_mesh: False"
	{% endif %}
	
	{% if beacon_scan_method_automatic %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon 'automatic' scan method is enabled" MSG="Beacon 'automatic' scan method is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_scan_method_automatic: False"
	{% endif %}
	
	{% if beacon_contact_z_tilt_adjust %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact z-tilt adjust is enabled" MSG="Beacon contact z-tilt adjust is enabled. This is not recommended for normal use and may result in inaccurate z-tilt adjustment._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_z_tilt_adjust: False"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH]
gcode = 
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE=None
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE=None
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION {rawparams}
	{% endif %}

[gcode_macro _START_PRINT_BED_MESH]
variable_actual_true_zero_position_x = None
variable_actual_true_zero_position_y = None
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set X=[params.X0|default(-1)|float, params.X1|default(-1)|float] %}
	{% set Y=[params.Y0|default(-1)|float, params.Y1|default(-1)|float] %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_BED_MESH" MSG="idex_mode: {idex_mode}, X: {X}, Y: {Y}"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is not defined %}
	{% set zero_ref_pos = [safe_home_x if actual_true_zero_position_x is none else actual_true_zero_position_x, safe_home_y if actual_true_zero_position_y is none else actual_true_zero_position_y] %}
	{% endif %}
	
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	
	
	
	
	{% set X=[0, printable_x_max] %}
	{% endif %}
	
	
	{% set beacon_bed_mesh_scv = printer["gcode_macro RatOS"].beacon_bed_mesh_scv|default(25)|int %}
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% if printer.fastconfig.settings.beacon is defined and not beacon_contact_bed_mesh %}
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={beacon_bed_mesh_scv}
	{% endif %}
	
	
	{% set default_profile = printer["gcode_macro RatOS"].bed_mesh_profile|default('ratos') %}
	{% if printer["gcode_macro RatOS"].calibrate_bed_mesh|lower == 'true' %}
	BED_MESH_CLEAR
	{% if printer["gcode_macro RatOS"].adaptive_mesh|lower == 'true' %}
	CALIBRATE_ADAPTIVE_MESH PROFILE="{default_profile}" X0={X[0]} X1={X[1]} Y0={Y[0]} Y1={Y[1]} T={params.T|int} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={idex_mode} ZERO_REF_POS_X={zero_ref_pos[0]} ZERO_REF_POS_Y={zero_ref_pos[1]}
	{% else %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	BED_MESH_PROFILE LOAD="{default_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	
	{% elif printer["gcode_macro RatOS"].bed_mesh_profile is defined %}
	BED_MESH_CLEAR
	BED_MESH_PROFILE LOAD="{printer["gcode_macro RatOS"].bed_mesh_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"

[gcode_macro CALIBRATE_ADAPTIVE_MESH]
gcode = 
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set default_profile = params.PROFILE %}
	
	
	{% set x0 = params.X0|default(-1)|float %}
	{% set y0 = params.Y0|default(-1)|float %}
	{% set x1 = params.X1|default(-1)|float %}
	{% set y1 = params.Y1|default(-1)|float %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Received coordinates X0={x0|round(1)} Y0={y0|round(1)} X1={x1|round(1)} Y1={y1|round(1)}"
	
	{% if x0 >= x1 or y0 >= y1 %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Invalid coordinates received. Please check your slicer settings. Falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	
	
	{% if params.ZERO_REF_POS_X is defined and params.ZERO_REF_POS_Y is defined %}
	{% set zero_ref_pos_x = params.ZERO_REF_POS_X|float %}
	{% set zero_ref_pos_y = params.ZERO_REF_POS_Y|float %}
	{% if zero_ref_pos_x < x0 or zero_ref_pos_x > x1 or zero_ref_pos_y < y0 or zero_ref_pos_y > y1 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Zero reference position X={zero_ref_pos_x|round(1)} Y={zero_ref_pos_y|round(1)} is outside the mesh region, expanding mesh region to include it."
	{% set x0 = [x0, zero_ref_pos_x]|min %}
	{% set y0 = [y0, zero_ref_pos_y]|min %}
	{% set x1 = [x1, zero_ref_pos_x]|max %}
	{% set y1 = [y1, zero_ref_pos_y]|max %}
	{% endif %}
	{% endif %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float %}
	
	
	{% set mesh_x0 = [[x0, max_x]|min, min_x]|max %}
	{% set mesh_y0 = [[y0, max_y]|min, min_y]|max %}
	{% set mesh_x1 = [[x1, max_x]|min, min_x]|max %}
	{% set mesh_y1 = [[y1, max_y]|min, min_y]|max %}
	
	{% if mesh_x0 == min_x and mesh_y0 == min_y and mesh_x1 == max_x and mesh_y1 == max_y %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Print is using the full bed, falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	
	{% set probe_count_x = mesh_config.probe_count.split(",")[0]|int %}
	{% if mesh_config.probe_count.split(",")|length == 2 %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[1]|int %}
	{% else %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[0]|int %}
	{% endif %}
	
	
	{% set probe_x_step = (max_x - min_x) / probe_count_x %}
	{% set probe_y_step = (max_y - min_y) / probe_count_y %}
	
	
	{% set mesh_count_x = ([(mesh_x1 - mesh_x0) / probe_x_step, 3]|max)|int %}
	{% set mesh_count_y = ([(mesh_y1 - mesh_y0) / probe_y_step, 3]|max)|int %}
	{% set min_mesh_count = [mesh_count_x, mesh_count_y]|min %}
	{% set max_mesh_count = [mesh_count_x, mesh_count_y]|max %}
	
	
	{% set algorithm = mesh_config.algorithm %}
	{% if algorithm|lower == 'lagrange' and max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="cannot exceed a probe_count of 6 when using lagrange interpolation. Falling back to bicubic interpolation."
	{% set algorithm = 'bicubic' %}
	{% endif %}
	{% if algorithm|lower == 'bicubic' and min_mesh_count < 4 %}
	{% if max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="invalid probe_count option when using bicubic interpolation. Combination of 3 points on one axis with more than 6 on another is not permitted. Forcing minimum mesh count to be 4."
	{% set min_mesh_count = 4 %}
	{% else %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="bicubic interpolation with a probe_count of less than 4 points detected. Forcing lagrange interpolation."
	{% set algorithm = 'lagrange' %}
	{% endif %}
	{% endif %}
	
	{% set mesh_count_x = ([min_mesh_count, mesh_count_x]|max)|int %}
	{% set mesh_count_x = ([max_mesh_count, mesh_count_x]|min)|int %}
	{% set mesh_count_y = ([min_mesh_count, mesh_count_y]|max)|int %}
	{% set mesh_count_y = ([max_mesh_count, mesh_count_y]|min)|int %}
	
	{% set should_prime = printer["gcode_macro RatOS"].nozzle_priming == 'primeblob' %}
	{% if printer["dual_carriage"] is not defined %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% else %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 != 0 and probe_first %}
	{% set probe_first = false %}
	{% elif printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 == 0 and not probe_first %}
	{% set probe_first = true %}
	{% endif %}
	
	
	{% if should_prime and probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="mesh coordinates X0={mesh_x0|round(1)} Y0={mesh_y0|round(1)} X1={mesh_x1|round(1)} Y1={mesh_y1|round(1)}"
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y} RELATIVE_REFERENCE_INDEX=-1
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	
	
	{% if should_prime and not probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro M84]
rename_existing = M84.1
gcode = 
	
	M84.1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_OFFSET X=0 Y=0
	
	
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro _VAOC"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False
	{% endif %}
	
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	SET_SKEW CLEAR=1
	
	
	_LED_MOTORS_OFF

[gcode_macro M104]
rename_existing = M104.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M104" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set temperature_offset_t0 = printer["gcode_macro T0"].temperature_offset|default(0)|int %}
	{% set temperature_offset_t1 = printer["gcode_macro T1"].temperature_offset|default(0)|int %}
	{% set s0 = [s + temperature_offset_t0, 0]|max %}
	{% set s1 = [s + temperature_offset_t1, 0]|max %}
	{% if temperature_offset_t0 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t0}°C added to toolhead T0."
	{% endif %}
	{% if temperature_offset_t1 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t1}°C added to toolhead T1."
	{% endif %}
	{% else %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	M104.1 S{s0} T0
	M104.1 S{s1} T1
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% else %}
	M104.1 S{s} T{t}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M109]
rename_existing = M109.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M109" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M109" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	M109.1 S{s} T{t}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro SET_HEATER_TEMPERATURE]
rename_existing = SET_HEATER_TEMPERATURE_BASE
gcode = 
	
	{% set heater = params.HEATER|default("") %}
	{% set target = params.TARGET|default(0)|int %}
	
	DEBUG_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="heater: {heater}, target: {target}"
	
	{% set t = -1 %}
	{% if heater|lower == "extruder" or heater|lower == "extruder1" %}
	
	{% set t = 0 if heater|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and target > 0 %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set target = [target + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE_BASE HEATER="{heater}" TARGET={target}
	
	{% if t != -1 and printer.fastconfig.settings.beacon is defined %}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro TEMPERATURE_WAIT]
rename_existing = TEMPERATURE_WAIT_BASE
gcode = 
	
	{% set sensor = params.SENSOR|default("") %}
	{% set minimum = params.MINIMUM|default(-1)|int %}
	{% set maximum = params.MAXIMUM|default(-1)|int %}
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="sensor: {sensor}, minimum: {minimum}, maximum: {maximum}"
	
	{% set t = -1 %}
	{% if sensor|lower == "extruder" or sensor|lower == "extruder1" %}
	
	{% set t = 0 if sensor|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and (minimum > 0 or maximum > 0) %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% if minimum > -1 %}
	{% set minimum = [minimum + temperature_offset, 0]|max %}
	{% endif %}
	{% if maximum > -1 %}
	{% set maximum = [maximum + temperature_offset, 0]|max %}
	{% endif %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set id = "sensor " ~ sensor if t == -1 else "toolhead T" ~ t %}
	
	
	{% if minimum > -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum} MAXIMUM={maximum}
	{% elif minimum > -1 and maximum == -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum}
	{% elif minimum == -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MAXIMUM={maximum}
	{% else %}
	
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="neither MINIMUM or MAXIMUM args were specified, call TEMPERATURE_WAIT_BASE is expected to fail"
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}"
	{% endif %}
	
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature for {id} reached."

[gcode_macro SDCARD_PRINT_FILE]
rename_existing = SDCARD_PRINT_FILE_BASE
gcode = 
	{% if printer["ratos"] is defined %}
	PROCESS_GCODE_FILE { rawparams }
	{% else %}
	SDCARD_PRINT_FILE_BASE { rawparams }
	{% endif %}

[gcode_macro SKEW_PROFILE]
rename_existing = SKEW_PROFILE_BASE
variable_loaded_profile = ""
gcode = 
	{% if params.LOAD is defined %}
	{% if printer.fastconfig.settings["skew_correction %s" % params.LOAD] is defined %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='"{params.LOAD}"'
	{% endif %}
	{% endif %}
	
	SKEW_PROFILE_BASE { rawparams }

[gcode_macro SET_SKEW]
rename_existing = SET_SKEW_BASE
gcode = 
	{% if params.CLEAR is defined %}
	{% if params.CLEAR|default(0)|int == 1 %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='""'
	{% endif %}
	{% endif %}
	
	SET_SKEW_BASE { rawparams }

[gcode_macro SET_VELOCITY_LIMIT]
rename_existing = SET_VELOCITY_LIMIT_BASE
gcode = 
	{% if params.ACCEL_TO_DECEL is defined %}
	
	{% if params.ACCEL is defined %}
	{% set accel = params.ACCEL|float %}
	{% else %}
	{% set accel = printer.toolhead.max_accel|float %}
	{% endif %}
	
	{% if params.VELOCITY is defined %}
	{% set velocity = params.VELOCITY|float %}
	{% else %}
	{% set velocity = printer.toolhead.max_velocity|float %}
	{% endif %}
	
	{% if params.SQUARE_CORNER_VELOCITY is defined %}
	{% set scv = params.SQUARE_CORNER_VELOCITY|float %}
	{% else %}
	{% set scv = printer.toolhead.square_corner_velocity|float %}
	{% endif %}
	
	{% set mcr = params.ACCEL_TO_DECEL|float / accel %}
	
	DEBUG_ECHO PREFIX="SET_VELOCITY_LIMIT" MSG="ACCEL={accel}, VELOCITY={velocity}, SQUARE_CORNER_VELOCITY={scv}, MINIMUM_CRUISE_RATIO={mcr}"
	
	SET_VELOCITY_LIMIT_BASE ACCEL={accel} VELOCITY={velocity} SQUARE_CORNER_VELOCITY={scv} MINIMUM_CRUISE_RATIO={1-mcr}
	
	{% else %}
	
	SET_VELOCITY_LIMIT_BASE { rawparams }
	
	{% endif %}

[gcode_macro BED_MESH_CALIBRATE]
rename_existing = _BED_MESH_CALIBRATE_BASE
variable_abl_and_home_z_if_required = True
gcode = 
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	{% if abl_and_home_z_if_required %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% endif %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set beacon_default_probe_method = printer.fastconfig.settings.beacon.default_probe_method|default('proximity') %}
	{% set probe_method = params.PROBE_METHOD|default(beacon_default_probe_method)|lower %}
	{% if probe_method == 'proximity' %}
	_CHECK_ACTIVE_BEACON_MODEL_TEMP TITLE="Bed mesh calibration warning"
	{% endif %}
	{% endif %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_BED_MESH_CALIBRATE_BASE {rawparams}
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	_APPLY_RATOS_BED_MESH_PARAMETERS {rawparams}
	{% endif %}

[gcode_macro SET_GCODE_OFFSET]
rename_existing = SET_GCODE_OFFSET_BASE
gcode = 
	DEBUG_ECHO PREFIX="SET_GCODE_OFFSET" MSG="{rawparams|replace('"', '')|replace("'", '')}"
	{% set z_before = printer.gcode_move.homing_origin.z|float %}
	SET_GCODE_OFFSET_BASE {rawparams}
	_AFTER_SET_GCODE_OFFSET Z_BEFORE={z_before}

[gcode_macro _AFTER_SET_GCODE_OFFSET]
gcode = 
	{% set z_before = params.Z_BEFORE|float %}
	{% set z_after = printer.gcode_move.homing_origin.z|float %}
	{% if z_before != z_after %}
	_ALERT_NON_ZERO_Z_OFFSET FORCE=1
	{% endif %}

[gcode_macro _START_PRINT_PARK]
gcode = 
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_x = printer["gcode_macro RatOS"].start_print_park_x %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% if printer["gcode_macro RatOS"].start_print_park_x is defined and printer["gcode_macro RatOS"].start_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="start_print_park_x is ignored for IDEX printers"
	{% endif %}
	PARK_TOOLHEAD
	G90
	{% endif %}
	
	
	_PARK LOCATION={start_print_park_in} X={start_print_park_x}
	G0 Z{z} F{z_speed}

[gcode_macro _END_PRINT_PARK]
gcode = 
	{% if printer["dual_carriage"] is defined %}
	
	{% if printer["gcode_macro RatOS"].end_print_park_x is defined and printer["gcode_macro RatOS"].end_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="end_print_park_x is ignored for IDEX printers"
	{% endif %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	PARK_TOOLHEAD
	G90
	{% endif %}
	_PARK LOCATION={printer["gcode_macro RatOS"].end_print_park_in} X={printer["gcode_macro RatOS"].end_print_park_x}

[gcode_macro _PARK]
gcode = 
	
	{% set x = params.X %}
	{% set location = params.LOCATION|default('back')|lower %}
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	{% set nozzle_priming = printer["gcode_macro RatOS"].nozzle_priming|lower %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="park"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% if x != '' %}
	{% if x|float >= printer.toolhead.axis_minimum.x + 5 and x|float <= printable_x_max - 5 %}
	{% set park_x = x|float %}
	{% else %}
	{action_respond_info('The requested X co-ordinate is outside the defined axis bounds - using defaults')}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	{% else %}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	
	
	{% set park_y = printable_y_max - 15 %}
	{% if location == 'front' %}
	{% set park_y = printer.toolhead.axis_minimum.y + 5 %}
	{% elif location == 'center' %}
	{% set park_y = printable_y_max / 2 %}
	{% elif location == 'primeblob' and printer["dual_carriage"] is defined %}
	
	{% set park_y = printable_y_max - 15 %}
	{% endif %}
	
	
	{% if location == 'primeblob' and printer["dual_carriage"] is not defined %}
	{% if (nozzle_priming == 'primeblob' or nozzle_priming == 'primeline') %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set park_x = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set park_x = printable_x_max - 5 %}
	{% else %}
	{% set park_x = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set park_y = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set park_y = printable_y_max - 5 %}
	{% else %}
	{% set park_y = nozzle_prime_start_y|float %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	G0 X{park_x} Y{park_y} F{speed}
	{% else %}
	
	G0 Y{park_y} F{speed}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="park"

[gcode_macro SAVE_PROBE_RESULT]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	{% set last_z_offset = 9999.9 %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if beacon_contact_prime_probing %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	{% else %}
	{% set last_z_offset = printer.beacon.last_sample.dist - current_z %}
	{% endif %}
	{% elif printer.fastconfig.settings.bltouch is defined  %}
	{% set config_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% elif printer.fastconfig.settings.probe is defined  %}
	{% set config_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% endif %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Saving offset adjustment of {last_z_offset} in {params.VARIABLE|default('last_z_offset')}"
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={params.VARIABLE|default('last_z_offset')} VALUE={last_z_offset}

[gcode_macro PROBE_FOR_PRIMING]
gcode = 
	
	{% set probe_for_priming_disable_mesh_constraints = true if printer["gcode_macro RatOS"].probe_for_priming_disable_mesh_constraints|default(false)|lower == 'true' else false %}
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower != 'false' %}
	SAVE_GCODE_STATE NAME=probe_for_priming_state
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the prime location.."
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set t = params.TOOLHEAD|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% if idex_mode == '' %}
	
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% if t == 0 %}
	{% set x_start = 5 %}
	{% else %}
	{% set x_start = printable_x_max - 5 %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% endif %}
	{% endif %}
	{% set z = printer.fastconfig.settings.bed_mesh.horizontal_move_z|float %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% if printer.fastconfig.settings.bltouch is defined %}
	{% set x_offset = printer.fastconfig.settings.bltouch.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.bltouch.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% elif printer.fastconfig.settings.probe is defined %}
	{% set x_offset = printer.fastconfig.settings.probe.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.probe.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% elif printer.fastconfig.settings.beacon is defined %}
	{% set x_offset = printer.fastconfig.settings.beacon.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.beacon.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.beacon.trigger_distance|float %}
	{% else %}
	{ action_raise_error("No probe, beacon or bltouch section found. Adaptive priming only works with a [probe], [beacon] or [bltouch] section defined.") }
	{% endif %}
	
	{% if z < z_offset %}
	{ action_raise_error("Horizontal move Z ({z}) is below your probe's Z offset ({z_offset}). Please adjust your horizontal_move_z setting in [bed_mesh] to be above {z}.") }
	{% endif %}
	
	{% if not probe_for_priming_disable_mesh_constraints %}
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float - x_offset %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float - y_offset %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float - x_offset %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float - y_offset %}
	
	
	{% set x_start = [[x_start, max_x]|min, min_x]|max %}
	{% set y_start = [[y_start, max_y]|min, min_y]|max %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the start of the prime location at {x_start}, {y_start}"
	
	G90
	
	M83
	
	G0 Z{z} F{z_speed}
	
	G1 X{x_start} Y{y_start} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result
	{% endif %}
	
	{% if idex_mode == '' %}
	
	{% set x_end = x_start %}
	{% set y_end = y_start + 45 %}
	{% else %}
	
	{% if t==1 %}
	{% set x_end = x_start - 45 %}
	{% else %}
	{% set x_end = x_start + 45 %}
	{% endif %}
	{% set y_end = y_start %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the end of the prime location at {x_end}, {y_end}"
	G1 X{x_end} Y{y_end} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result
	{% endif %}
	
	RESTORE_GCODE_STATE NAME=probe_for_priming_state
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	{% endif %}

[gcode_macro RESET_PRIME_PROBE_STATE]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result VALUE=None
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result_t1 VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result_t1 VALUE=None
	{% endif %}

[gcode_macro PROBE_CURRENT_POSITION]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	SAVE_GCODE_STATE NAME=probe_current_position_state
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	ASSERT_PROBE_DEPLOYED
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_prime_probing %}
	PROBE PROBE_METHOD=contact SAMPLES=1
	{% else %}
	PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	BEACON_QUERY
	{% else %}
	
	RESTORE_GCODE_STATE NAME=probe_current_position_state MOVE=1 MOVE_SPEED={printer["gcode_macro RatOS"].macro_z_speed|float}
	{% endif %}

[gcode_macro PRIME_BLOB]
description = Prints a primeblob, used internally, if configured, as part of the START_PRINT macro.
variable_x_offset = 5
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="prime_blob"
	SET_MACRO_TRAVEL_SETTINGS
	
	RATOS_ECHO PREFIX="Priming" MSG="Priming nozzle with prime blob.."
	
	
	{% set current_toolhead = 0 %}
	
	
	{% set target_idex_mode = '' %}
	{% set extruder = 'extruder' %}
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE is defined %}
	{% set target_idex_mode = params.IDEX_MODE|default('')|lower %}
	{% else %}
	{ action_raise_error("IDEX_MODE parameter not found for PRIME_BLOB macro. This is likely a bug.") }
	{% endif %}
	RATOS_ECHO PREFIX="Priming" MSG="Priming in IDEX {target_idex_mode} mode.."
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set current_toolhead = 1 if current_idex_mode=='primary' else 0 %}
	{% set extruder = 'extruder1' if current_toolhead == 1 else 'extruder' %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	SAVE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set fan_speed = printer["gcode_macro RatOS"].nozzle_prime_bridge_fan|float %}
	{% set nozzle_diameter = printer.fastconfig.settings[extruder].nozzle_diameter|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set has_start_offset_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) != 9999.9 %}
	{% if printer["dual_carriage"] is defined %}
	{% set has_start_offset_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) != 9999.9 %}
	{% endif %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_z_height = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set nozzle_prime_direction = printer["gcode_macro RatOS"].nozzle_prime_direction|lower %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% if target_idex_mode == '' %}
	
	{% set x_factor = 0 %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% set y_factor = -1 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% if nozzle_prime_start_y|float < printable_y_max / 2 %}
	{% set y_factor = 1 %}
	{% else %}
	{% set y_factor = -1 %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_direction == 'forwards' %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_direction == 'backwards' %}
	{% set y_factor = -1 %}
	{% endif %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% else %}
	{% set z = start_print_park_z_height %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% set y_factor = 0 %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set x_start = center_x / 2 + 5 %}
	{% set x_factor = 1 %}
	{% else %}
	
	
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% if current_toolhead == 0 %}
	{% set x_start = 55 %}
	{% set x_factor = -1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 55 %}
	{% set x_factor = 1 %}
	{% endif %}
	{% else %}
	{% if current_toolhead == 0 %}
	{% set x_start = 5 %}
	{% set x_factor = 1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 5 %}
	{% set x_factor = -1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_x_max - 5 %}
	{% endif %}
	{% set z = 10 %}
	{% endif %}
	
	{% set start_z_offset = 0 %}
	{% set end_z_offset = 0 %}
	{% if has_start_offset_t0 %}
	{% set start_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) %}
	{% set end_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_end_result|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t0) ) }
	{% endif %}
	{% if end_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t0) )  }
	{% endif %}
	{% set start_z_offset = start_z_probe_result_t0 %}
	{% set end_z_offset = end_z_probe_result_t0 %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	{% if current_toolhead == 1 or both_toolheads or target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	{% if has_start_offset_t1 %}
	{% set start_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) %}
	{% set end_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_end_result_t1|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t1) ) }
	{% endif %}
	{% if end_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t1) ) }
	{% endif %}
	{% set start_z_offset = [start_z_offset, start_z_probe_result_t1]|max %}
	{% set end_z_offset = [end_z_offset, start_z_probe_result_t1]|max %}
	{% endif %}
	{% endif %}
	{% if target_idex_mode != 'copy' and target_idex_mode != 'mirror' %}
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% set original_start_z_offset = start_z_offset %}
	{% set original_end_z_offset = end_z_offset %}
	{% set start_z_offset = original_end_z_offset %}
	{% set end_z_offset = original_start_z_offset %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	DEBUG_ECHO PREFIX="PRIME_BLOB" MSG="x_start: {x_start}, y_start: {y_start}, x_factor: {x_factor}, y_factor: {y_factor}, z: {z}, start_z_offset: {start_z_offset}, end_z_offset: {end_z_offset}"
	
	
	G90
	
	M83
	RATOS_ECHO PREFIX="Priming" MSG="Lifting Z to {z}.."
	
	G0 Z{z} F{z_speed}
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% if start_print_park_in != 'primeblob' %}
	G1 X{x_start} F{speed}
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% endif %}
	{% else %}
	
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% if target_idex_mode=="copy" or target_idex_mode=="mirror" %}
	RATOS_ECHO PREFIX="Priming" MSG="Mirroring move to {x_start}, {y_start} along the edge of the print area.."
	
	_IDEX_MIRROR PRIMING=1
	{% else %}
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% endif %}
	G1 X{x_start} F{speed}
	{% endif %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Starting prime blob.."
	
	G1 Z{0.5 + start_z_offset} F{z_speed}
	
	G1 Y{y_start} F{speed}
	
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	
	M106 S{fan_speed}
	
	G1 Z5 F100 E5
	G92 E0
	RATOS_ECHO PREFIX="Priming" MSG="Bridging with {((fan_speed/255) * 100)|int}% fan speed.."
	
	G1 F3000 X{x_start + (15 * x_factor)} Y{y_start + (15 * y_factor)} E{1 / ((0.4 / nozzle_diameter) ** 2)}
	
	
	
	G1 F3000 X{x_start + (20 * x_factor)} Y{y_start + (20 * y_factor)} Z{3.8 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (34 * x_factor)} Y{y_start + (34 * y_factor)} Z{2.6 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (38 * x_factor)} Y{y_start + (38 * y_factor)} Z{1.4 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (42 * x_factor)} Y{y_start + (42 * y_factor)} Z{0.2 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	
	M106 S0
	
	G1 F3000 X{x_start + (46 * x_factor)} Y{y_start + (46 * y_factor)} Z{0.2 + end_z_offset} E0.6
	
	G1 F{speed} X{x_start + (50 * x_factor)} Y{y_start + (50 * y_factor)}
	
	
	{% if target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if target_idex_mode == "copy" %}
	{% if first_y >= 0 %}
	_IDEX_COPY DANCE=0 Y={first_y}
	{% else %}
	_IDEX_COPY DANCE=0 Y={params.Y1}
	{% endif %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	RESTORE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="prime_blob"
	
	
	G92 E0

[gcode_macro UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set temp = params.TEMP|default(220)|int %}
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_UNLOAD_FILAMENT TEMP={temp} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_UNLOAD_FILAMENT]
description = Unload filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_UNLOAD_FILAMENT" MSG="TEMP: {temp}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=unload_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	G4 P3000
	
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD=0 NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=unload_state
	
	
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament unloading completed"

[gcode_macro _IDEX_UNLOAD_FILAMENT]
description = Unload filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading T{toolhead} filament..."
	
	DEBUG_ECHO PREFIX="_IDEX_UNLOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} AUTOMATED={automated}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="T{toolhead} filament unloading completed"

[gcode_macro _UNLOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LEGACY_UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
gcode = 
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set unload_speed = 5 * 60 %}
	{% set unload_length = printer["gcode_macro RatOS"].filament_unload_length|float %}
	M117 Unloading filament...
	
	G0 E10 F300
	
	G0 E-5 F3600
	
	G4 P3000
	
	G0 E5 F6000
	
	G0 E-15 F6000
	
	G0 E-{unload_length} F{unload_speed}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}
	M117 Filament unloaded!
	RESPOND MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	RATOS_ECHO MSG="Unloading filament from nozzle to cooling zone... Please wait!"
	
	_PURGE_BEFORE_UNLOAD TOOLHEAD={toolhead}
	
	{% if printer["gcode_macro _UNLOAD_WITHOUT_TIP_FORMING"] is defined %}
	
	_UNLOAD_WITHOUT_TIP_FORMING TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	_UNLOAD_WITH_TIP_FORMING NAME='{filament_name}' TYPE='{filament_type}'
	{% endif %}
	
	G4 P3000

[gcode_macro _UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	{% set tooolhead_sensor_to_extruder_gear_distance = printer["gcode_macro T%s" % toolhead].tooolhead_sensor_to_extruder_gear_distance|float %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER" MSG="TOOLHEAD: {toolhead}"
	
	
	G0 E-{extruder_gear_to_cooling_position_distance + tooolhead_sensor_to_extruder_gear_distance + 50} F{extruder_load_speed}
	
	RATOS_ECHO MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_WITH_TIP_FORMING]
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	{% if filament_name != '' and filament_type != '' %}
	_UNLOAD_KNOWN_FILAMENT NAME={filament_name} TYPE={filament_type}
	{% else %}
	_UNLOAD_UNKNOWN_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _UNLOAD_KNOWN_FILAMENT]
description = User overrideable tip forming macro if slicer filament profiles are known
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	RATOS_ECHO PREFIX="FILAMENT TYPE" MSG='{filament_type}'
	RATOS_ECHO PREFIX="FILAMENT PROFILE" MSG='{filament_name}'
	
	
	{% if filament_name == "Prusament PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% elif filament_name == "Nobufil PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% else %}
	
	RATOS_ECHO PREFIX="_UNLOAD_KNOWN_FILAMENT" MSG="Filament profile not found!"
	_UNLOAD_UNKNOWN_FILAMENT
	{% endif %}

[gcode_macro _UNLOAD_UNKNOWN_FILAMENT]
description = User overrideable standard tip forming macro
gcode = 
	
	DEBUG_ECHO PREFIX="_UNLOAD_UNKNOWN_FILAMENT" MSG="Using standard tip forming macro!"
	
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10

[gcode_macro _TIP_FORMING]
gcode = 
	
	{% set cooling_moves = params.COOLING_MOVES|default(4)|int %}
	{% set cooling_move_length = params.COOLING_MOVE_LENGTH|default(10)|float %}
	{% set start_cooling_speed = params.START_COOLING_SPEED|default(10)|float * 60 %}
	{% set end_cooling_speed = params.END_COOLING_SPEED|default(50)|float * 60 %}
	{% if cooling_moves == 0 %}
	{% set cooling_move_length = 0 %}
	{% endif %}
	
	
	{% set dip = true if params.DIP|default(false)|lower == "true" else false %}
	{% set dip_length = params.DIP_LENGTH|default(22)|float %}
	{% set dip_speed = params.DIP_SPEED|default(30)|float * 60 %}
	{% set dip_retract_speed = params.DIP_RETRACT_SPEED|default(70)|float * 60 %}
	
	
	{% set retract_length = params.RETRACT_LENGTH|default(18)|float %}
	{% set start_retract_speed = params.START_RETRACT_SPEED|default(120)|float * 60 %}
	{% set end_retract_speed = params.END_RETRACT_SPEED|default(20)|float * 60 %}
	
	DEBUG_ECHO PREFIX="_TIP_FORMING" MSG="cooling_moves: {cooling_moves}, cooling_move_length: {cooling_move_length}, start_cooling_speed: {start_cooling_speed}, end_cooling_speed: {end_cooling_speed}, dip: {dip}, dip_length: {dip_length}, dip_speed: {dip_speed}, dip_retract_speed: {dip_retract_speed}, retract_length: {retract_length}, start_retract_speed: {start_retract_speed}, end_retract_speed: {end_retract_speed}"
	
	M220 S100
	
	
	G92 E0
	{% set retract = retract_length + cooling_move_length / 2 - 15 %}
	G1 E-15 F{start_retract_speed}
	G1 E-{0.7 * retract} F{1.0 * end_retract_speed}
	G1 E-{0.2 * retract} F{0.5 * end_retract_speed}
	G1 E-{0.1 * retract} F{0.3 * end_retract_speed}
	
	
	G92 E0
	{% if cooling_moves > 0 %}
	{% set i = (end_cooling_speed - start_cooling_speed) / (2 * cooling_moves - 1) %}
	{% for m in range(cooling_moves) %}
	G1 E{cooling_move_length} F{(start_cooling_speed + i * m * 2)}
	G1 E-{cooling_move_length} F{(start_cooling_speed + i * (m * 2 + 1))}
	{% endfor %}
	{% endif %}
	
	
	G92 E0
	{% if dip %}
	G1 E{dip_length} F{dip_speed}
	G4 P100
	G1 E-{dip_length} F{dip_retract_speed}
	{% endif %}
	
	G92 E0
	M400

[delayed_gcode __ON_FILAMENT_SENSOR_BUTTON_PRESSED_STARTUP_GUARD]
initial_duration = 2.
gcode = 
	SET_GCODE_VARIABLE MACRO=_ON_FILAMENT_SENSOR_BUTTON_PRESSED VARIABLE=startup_complete VALUE=True

[gcode_macro _ON_FILAMENT_SENSOR_BUTTON_PRESSED]
variable_startup_complete = False
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set toolhead_sensor_button_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_sensor_button_only_when_sensor_enabled|default(false)|lower == 'true' %}
	
	
	{% if not startup_complete and sensor_enabled %}
	{action_emergency_stop("RatOS: The T%s filament sensor button was triggered immediately on printer startup. This is likely a false trigger. Please check your filament sensor wiring and configuration!" % (toolhead,))}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_SENSOR_BUTTON_PRESSED" MSG="TOOLHEAD: {toolhead}, SENSOR_ENABLED: {sensor_enabled}, TOOLHEAD_SENSOR_BUTTON_ONLY_WHEN_SENSOR_ENABLED: {toolhead_sensor_button_only_when_sensor_enabled}"
	
	{% if not printer.virtual_sdcard.is_active and (sensor_enabled or not toolhead_sensor_button_only_when_sensor_enabled) %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	{% set toolhead_detect_clog_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_detect_clog_only_when_sensor_enabled|default(true)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}, ENABLE_CLOG_DETECTION: {enable_clog_detection}, TOOLHEAD_DETECT_CLOG_ONLY_WHEN_SENSOR_ENABLED: {toolhead_detect_clog_only_when_sensor_enabled}, SENSOR_ENABLED: {sensor_enabled}"
	
	{% if enable_clog_detection and (sensor_enabled or not toolhead_detect_clog_only_when_sensor_enabled) %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_clog_detection %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_FILAMENT_END]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set clogged = true if params.CLOGGED|default(false)|lower == 'true' else false %}
	
	
	{% set unload_after_runout = printer["gcode_macro T%s" % toolhead].unload_after_runout|float %}
	
	
	{% if clogged %}
	_LED_FILAMENT_CLOG TOOLHEAD={toolhead}
	{% else %}
	_LED_FILAMENT_RUNOUT TOOLHEAD={toolhead}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_END" MSG="TOOLHEAD: {toolhead}"
	
	{% if printer.virtual_sdcard.is_active %}
	{% if not printer.pause_resume.is_paused %}
	PAUSE RUNOUT=True
	{% endif %}
	{% if not clogged and unload_after_runout %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	{% if not clogged and printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true'%}
	_JOIN_SPOOL TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M600]
description = Executes a color change by pausing the printer an unloading the filament.
gcode = 
	PAUSE
	UNLOAD_FILAMENT AUTOMATED=True
	RATOS_ECHO MSG="Please load new filament and resume"

[gcode_macro COLD_PULL]
description = Automated hotend cold pull.
gcode = 
	
	{% set extrusion_temp = params.EXTRUSION_TEMP|default(220)|int %}
	{% set cold_pull_temp = params.COLD_PULL_TEMP|default(80)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	
	{% if printer["dual_carriage"] is not defined %}
	{% set toolhead = 0 %}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead != 0 and toolhead != 1 %}
	{action_raise_error("Please select toolhead! 0 = left, 1 = right toolhead")}
	{% endif %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	RATOS_ECHO MSG="Starting cold pull on T{toolhead}..."
	{% else %}
	RATOS_ECHO MSG="Starting cold pull..."
	{% endif %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	SAVE_GCODE_STATE NAME=cold_pull_state
	
	
	{% if printer["dual_carriage"] is defined and "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	RATOS_ECHO MSG="Heating T{toolhead} to {extrusion_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={extrusion_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={extrusion_temp} MAXIMUM={extrusion_temp + 2}
	
	
	G4 P3000
	
	
	RATOS_ECHO MSG="extruding..."
	G92 E0
	G1 E30 F300
	G92 E0
	
	
	RATOS_ECHO MSG="Cooling T{toolhead} to {cold_pull_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={cold_pull_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={cold_pull_temp} MAXIMUM={cold_pull_temp + 2}
	
	
	G4 P10000
	
	
	RATOS_ECHO MSG="cold pull..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-40 VELOCITY=5 ACCEL=100
	
	
	RATOS_ECHO MSG="eject filament..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-200 VELOCITY=20 ACCEL=500
	
	
	RATOS_ECHO MSG="cooling down extruder..."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	RESTORE_GCODE_STATE NAME=cold_pull_state
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	
	CONSOLE_ECHO TITLE="Cold pull complete" MSG="Please remove the filament from the PTFE tube and cut the end off. Do NOT try to load it again." TYPE="warning"

[gcode_macro _USER_START_PRINT_BEFORE_HOMING]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_BED]
gcode = 

[gcode_macro _USER_START_PRINT_BED_MESH]
gcode = 

[gcode_macro _USER_START_PRINT_PARK]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 

[gcode_macro _USER_START_PRINT_HEAT_CHAMBER]
description = Uses the extruder sensor to wait for chamber temp. Override the _START_PRINT_HEAT_CHAMBER macro to implement heated chamber handling.
gcode = 
	
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}

[gcode_macro _USER_END_PRINT_BEFORE_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_AFTER_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_PARK]
gcode = 

[gcode_macro _USER_END_PRINT_FINISHED]
description = User hook for when the print is finished after gcode state has been restored.
gcode = 

[gcode_macro _USER_START_PRINT]
gcode = 

[gcode_macro _USER_END_START_PRINT]
gcode = 

[gcode_macro _USER_START_FEATURE]
gcode = 

[gcode_macro _USER_END_FEATURE]
gcode = 

[gcode_macro _USER_BEFORE_IDLE_TIMEOUT]
gcode = 

[gcode_macro _USER_AFTER_IDLE_TIMEOUT]
gcode = 

[gcode_macro ECHO_T_VARS]
description = Echo Toolhead variables to the console.
gcode = 
	{% set t = params.T|default(0) %}
	RATOS_ECHO MSG="T{t} Variables"
	{% for var, value in printer["gcode_macro T%s" % t].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ECHO_RATOS_VARS]
description = Echo RatOS variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro RatOS"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ENSURE_CRITICAL_RATOS_INIT]
variable_completed = False
gcode = 
	{% if not completed %}
	CALCULATE_PRINTABLE_AREA
	SET_GCODE_VARIABLE MACRO=ENSURE_CRITICAL_RATOS_INIT VARIABLE=completed VALUE=True
	{% endif %}

[delayed_gcode RATOS_INIT]
initial_duration = 0.1
gcode = 
	{action_respond_info("Initializing RatOS...")}
	ENSURE_CRITICAL_RATOS_INIT
	_LED_STANDBY
	INITIAL_FRONTEND_UPDATE
	_CHAMBER_FILTER_SANITY_CHECK
	{% if printer.fastconfig.settings.beacon is defined %}
	
	_BED_MESH_SANITY_CHECK
	{% endif %}
	{% set svv = printer.save_variables.variables %}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=0 C={svv.nozzle_expansion_coefficient_t0|default(0.06)|float}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=1 C={svv.nozzle_expansion_coefficient_t1|default(0.06)|float}
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=idex_applied_offset

[delayed_gcode RATOS_LOGO]
initial_duration = 2
gcode = 
	
	
	
	
	
	ENSURE_CRITICAL_RATOS_INIT
	HELLO_RATOS
	_ALERT_NON_ZERO_Z_OFFSET

[gcode_macro _ALERT_NON_ZERO_Z_OFFSET]
gcode = 
	{% set force = params.FORCE|default(0)|int == 1 %}
	{% set user_offset = printer.named_offsets.user_probe_z_offset.z|float %}
	{% set gcode_offset = printer.gcode_move.homing_origin.z|float %}
	{% set combined_offset = user_offset + gcode_offset %}
	
	{% if force or user_offset != 0 or gcode_offset != 0 %}
	{% set title = "User-adjusted Z-offset of %.3f mm is active" % combined_offset %}
	{% set msg = "" %}
	{% set nl = "" %}
	{% if user_offset != 0 %}
	{% set msg = msg + "beacon true zero user Z-offset: %.3f mm (to clear, use Z_OFFSET_APPLY_PROBE CLEAR=1)" % user_offset %}
	{% set nl = "_N_" %}
	{% endif %}
	{% if gcode_offset != 0 %}
	{% set msg = msg + nl + "G-code Z-offset: %.3f mm" % gcode_offset %}
	{% endif %}
	CONSOLE_ECHO TITLE="{title}" TYPE="info" MSG="{msg}"
	{% endif %}

[gcode_macro _INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE]
gcode = 
	{% set variable = params.VARIABLE|string %}
	{% set svv = printer.save_variables.variables %}
	{% set nlu_msg = "no longer used, please remove" %}
	{% if svv[variable] is defined %}
	{% set v = svv[variable]|string|replace('"', '')|replace("'", "") %}
	{% if not nlu_msg in v %}
	SAVE_VARIABLE VARIABLE={variable} VALUE='"{nlu_msg} (was {v})"'
	{% endif %}
	CONSOLE_ECHO TITLE="Deprecated ratos-variables.cfg variable" TYPE="warning" MSG="The variable {variable} is no longer used, please remove it from your ratos-variables.cfg file."
	{% endif %}

[gcode_macro _NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK]
gcode = 
	
	
	
	
	
	
	
	{% set t = params.T|int %}
	{% set c = params.C|float %}
	{% set normal_low = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_low|default(0.05)|float %}
	{% set normal_high = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_high|default(0.10)|float %}
	
	{% if c < 0 %}
	
	{action_emergency_stop("Invalid nozzle_expansion_coefficient_t%s value in ratos-variables.cfg: %.3f. It must be non-negative." % (t, c))}
	{% endif %}
	{% if c >= normal_high %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite high. Please verify that this is correct."
	{% endif %}
	{% if c <= normal_low %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite low. Please verify that this is correct."
	{% endif %}

[gcode_macro INITIAL_FRONTEND_UPDATE]
gcode = 
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_error = printer["gcode_macro RatOS"].status_color_error|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_unknown}"'
	{% endif %}
	
	
	{% set t0_sensor = "undefined" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	{% set t0_sensor = "detected" %}
	{% else %}
	{% set t0_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t0_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	{% set t1_sensor = "undefined" %}
	{% if printer["dual_carriage"] is defined and printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	{% set t1_sensor = "detected" %}
	{% else %}
	{% set t1_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t1_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	{% if svv.t0_filament is defined and printer["gcode_macro T0"] is defined %}
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	{% if t0_sensor != "empty" %}
	{% set t0_filament_type = svv.t0_filament[0]|default('')|string %}
	{% set t0_filament_name = svv.t0_filament[1]|default('')|string %}
	{% set t0_filament_temp = svv.t0_filament[2]|default(0)|float %}
	{% if t0_filament_name != '' and t0_filament_type != '' and t0_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{t0_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{t0_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={t0_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}
	{% if svv.t1_filament is defined and printer["gcode_macro T1"] is defined %}
	{% if printer["gcode_macro T1"].filament_name is defined and printer["gcode_macro T1"].filament_type is defined and printer["gcode_macro T1"].filament_temp is defined %}
	{% if t1_sensor != "empty" %}
	{% set t1_filament_type = svv.t1_filament[0]|default('')|string %}
	{% set t1_filament_name = svv.t1_filament[1]|default('')|string %}
	{% set t1_filament_temp = svv.t1_filament[2]|default(0)|float %}
	{% if t1_filament_name != '' and t1_filament_type != '' and t1_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='"{t1_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='"{t1_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE={t1_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t1_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro CALCULATE_PRINTABLE_AREA]
variable_calculated = False
gcode = 
	{% if not calculated %}
	{% set bed_margin_x = printer["gcode_macro RatOS"].bed_margin_x %}
	{% set bed_margin_y = printer["gcode_macro RatOS"].bed_margin_y %}
	
	
	
	{% set tool = 0 if printer["gcode_macro T0"] is not defined or printer["gcode_macro T0"].active else 1 %}
	{% set max_x = printer.toolhead.axis_maximum.x if printer["dual_carriage"] is defined and tool == 0 else printer.toolhead.axis_maximum.x - bed_margin_x[1] %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	
	
	{% set max_x = printer.toolhead.axis_maximum.x %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="printer.toolhead.axis_maximum.x {printer.toolhead.axis_maximum.x}"
	
	{% set max_y = printer.toolhead.axis_maximum.y - bed_margin_y[1]%}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_x_max VALUE={max_x}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_y_max VALUE={max_y}
	SET_GCODE_VARIABLE MACRO=CALCULATE_PRINTABLE_AREA VARIABLE=calculated VALUE=True
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	RATOS_LOG PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	{% endif %}

[gcode_macro CACHE_TOOLHEAD_SETTINGS]
variable_cache = {"global": {"accel": 1000, "ratio": 0.5, "speed": 50, "scv": 5}}
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set dummy = cache.__setitem__(key, {"accel": printer.toolhead.max_accel, "ratio": printer.toolhead.minimum_cruise_ratio, "speed": printer.toolhead.max_velocity, "scv": printer.toolhead.square_corner_velocity}) %}
	SET_GCODE_VARIABLE MACRO=CACHE_TOOLHEAD_SETTINGS VARIABLE=cache VALUE="{cache | pprint | replace("\n", "") | replace("\"", "\\\"")}"
	DEBUG_ECHO PREFIX="CACHE_TOOLHEAD_SETTINGS" MSG="Toolhead settings cached for {key}. {printer.toolhead.max_accel} accel, {printer.toolhead.minimum_cruise_ratio} ratio, {printer.toolhead.max_velocity} velocity, {printer.toolhead.square_corner_velocity} scv."

[gcode_macro RESTORE_TOOLHEAD_SETTINGS]
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set values = printer["gcode_macro CACHE_TOOLHEAD_SETTINGS"].cache.__getitem__(key) %}
	{% if values is not defined or values == 'None' %}
	{ action_raise_error("RESTORE_TOOLHEAD_SETTINGS: Toolhead settings not cached for key '" ~ key ~ "'.") }
	{% endif %}
	SET_VELOCITY_LIMIT ACCEL={values.accel} MINIMUM_CRUISE_RATIO={values.ratio} VELOCITY={values.speed} SQUARE_CORNER_VELOCITY={values.scv}
	DEBUG_ECHO PREFIX="RESTORE_TOOLHEAD_SETTINGS" MSG="Toolhead settings restored. {values.accel} accel, {values.ratio} ratio, {values.speed} velocity, {values.scv} scv."

[gcode_macro SET_MACRO_TRAVEL_SETTINGS]
gcode = 
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float %}
	{% set accel = printer["gcode_macro RatOS"].macro_travel_accel %}
	SET_VELOCITY_LIMIT ACCEL={accel} MINIMUM_CRUISE_RATIO=0.5 VELOCITY={speed} SQUARE_CORNER_VELOCITY={5}
	DEBUG_ECHO PREFIX="SET_MACRO_TRAVEL_SETTINGS" MSG="Macro travel settings set. {accel} accel, {speed} velocity"

[gcode_macro SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% if printer["dual_carriage"] is not defined %}
	
	SET_KINEMATIC_POSITION X={printable_x_max / 2} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	{% else %}
	
	IDEX_SET_CENTER_KINEMATIC_POSITION
	{% endif %}

[gcode_macro IDEX_SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x - (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x + (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY

[gcode_macro VERIFY_HYBRID_INVERTED]
gcode = 
	
	{% set inverted = False %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy is defined and printer.fastconfig.settings.ratos_hybrid_corexy.inverted is defined %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy.inverted|lower == 'true' %}
	{% set inverted = True %}
	{% endif %}
	{% endif %}
	{% if inverted == False %}
	{ action_emergency_stop("ratos_hybrid_corexy NOT INVERTED! Inverted hybrid core-xy bugfix not detected.") }
	{% endif %}

[gcode_macro RATOS_ECHO]
gcode = 
	{% set prefix = "RatOS" %}
	{% set debug = params.DEBUG|default(0)|int %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " | " ~ params.PREFIX %}
	{% endif %}
	{% set prefix = prefix ~ ":" %}
	{% set msg = "" %}
	{% if params.MSG is defined %}
	{% set msg = params.MSG %}
	{% else %}
	{% set msg = "No msg parameter provided (this is a bug or unintended use)." %}
	{% endif %}
	{% if not debug %}
	
	M117 {prefix} {msg}
	{% endif %}
	RATOS_LOG PREFIX="{prefix}" MSG="{msg}"
	{% if not debug %}
	RESPOND PREFIX="{prefix}" MSG="{msg}"
	{% else %}
	CONSOLE_ECHO TITLE="{prefix}" TYPE="debug" MSG="{msg}"
	{% endif %}

[gcode_macro ENABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=True
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=prefix_filter VALUE="'{params.FILTER|default('')|lower}'"
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging enabled."

[gcode_macro DISABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=False
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging disabled."

[gcode_macro DEBUG_ECHO]
variable_enabled = False
variable_prefix_filter = ''
gcode = 
	{% set prefix = "DEBUG" %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " - " ~ params.PREFIX %}
	{% endif %}
	{% if enabled and (prefix_filter|lower == '' or prefix_filter|lower in params.PREFIX|lower) %}
	RATOS_ECHO PREFIX="{prefix}" MSG="{params.MSG}" DEBUG=1
	{% endif %}

[gcode_macro START_FEATURE]
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="Start {params.FEATURE} feature gcode"
	{% set scv = printer.toolhead.square_corner_velocity|int|default(5) %}
	{% set accel = printer.toolhead.max_accel|int|default(10000) %}
	{% set ratio = printer.toolhead.minimum_cruise_ratio|float|default(0.5) %}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="scv" VALUE={scv}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="accel" VALUE={accel}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="ratio" VALUE={ratio}
	_USER_START_FEATURE FEATURE="{params.FEATURE}"

[gcode_macro END_FEATURE]
variable_scv = 5
variable_accel = 10000
variable_ratio = 0.5
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="End {params.FEATURE} feature gcode"
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={scv} ACCEL={accel} MINIMUM_CRUISE_RATIO={ratio}
	_USER_END_FEATURE FEATURE="{params.FEATURE}" SCV={scv} ACCEL={accel} RATIO={ratio}

[gcode_macro _ON_LAYER_CHANGE]
variable_layer_number = 0
description = INTERNAL USE ONLY. Call it from the slicers after layer change custom gcode
gcode = 
	
	{% set layer = params.LAYER|int %}
	
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE={layer}
	SET_PRINT_STATS_INFO CURRENT_LAYER={layer}

[gcode_macro _LEARN_MORE_CALIBRATION]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/calibration" %}
	{% set link_text = "RatOS Calibration Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_CHAMBER_FILTER]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter Control" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_FILAMENT]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/filaments" %}
	{% set link_text = "RatOS Filament Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _CONSOLE_SAVE_CONFIG]
gcode = 
	M118 Click <a class="command text--blue">SAVE_CONFIG</a> to save the settings to your printer.cfg.

[gcode_macro _LOAD_RATOS_SKEW_PROFILE]
gcode = 
	{% set ratos_skew_profile = printer["gcode_macro RatOS"].skew_profile|default("") %}
	{% if ratos_skew_profile != "" %}
	{% if printer.fastconfig.config["skew_correction %s" % ratos_skew_profile] is defined %}
	SKEW_PROFILE LOAD={ratos_skew_profile}
	GET_CURRENT_SKEW
	{% else %}
	{% set line_1 = '"Could not find skew profile %s!_N_Clearing skew correction."' % ratos_skew_profile %}
	CONSOLE_ECHO TITLE="Missing skew profile!" TYPE="warning" MSG={line_1}
	SET_SKEW CLEAR=1
	{% endif %}
	{% endif %}

[gcode_macro M601]
gcode = 
	PAUSE

[gcode_macro _STOP_AND_RAISE_ERROR]
gcode = 
	M84
	_RAISE_ERROR MSG="{params.MSG}"

[gcode_macro _RESET_GCODE_VARIABLES]
description = Reset specified [gcode_macro ...] variables to their original values from configuration when Klipper started.
	- MACRO: Name of the GCODE macro containing the variables to reset.
	- VARIABLES: Comma-separated list of variable names to reset (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- QUIET: (optional) If true, suppresses console echo messages for each reset variable. Default is false.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set quiet = params.QUIET|default("false")|lower in ("true", "1", "yes") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	{% set settings = printer.fastconfig.settings[obj_name|lower] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro %s]" % macro) }
	{% endif %}
	
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if settings["variable_%s" % var] is not defined %}
	{ action_raise_error("Variable '%s' is not defined in settings for [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	
	{% for var in vars %}
	{% set var_value = obj[var] %}
	{% if var_value is defined %}
	{% set v = settings["variable_%s" % var] %}
	{% if v != var_value|string %}
	{% if var_value is string %}
	{% set v = '"\'' ~ v|replace('"', '\\"')|replace("'", "\\'") ~ '\'"' %}
	{% endif %}
	SET_GCODE_VARIABLE MACRO={macro} VARIABLE={var} VALUE={v}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Reset {macro} variable {var} to original value: {v} (was {obj[var]})"
	{% endif %}
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro _SHOW_GCODE_VARIABLES]
description = Show current values of specified [gcode_macro ...] variables.
	- MACRO: Name of the GCODE macro containing the variables to show.
	- VARIABLES: Comma-separated list of variable names to show (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- PAD: (optional) If defined, provide a single character to use for padding variable names to align values in a tabular format in the console output. Default is no padding.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set pad = params.PAD|default("") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	
	{% set ns = namespace() %}
	{% set ns.max_len = 0 %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% set ns.max_len = (ns.max_len, var|length)|max %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if pad %}
	{% set padding = pad * (ns.max_len - var|length) %}
	CONSOLE_ECHO MSG="{var}{padding} {obj[var]}"
	{% else %}
	CONSOLE_ECHO MSG="{var}: {obj[var]}"
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro PAUSE]
description = Pauses the print
rename_existing = PAUSE_BASE
variable_extrude = 1.5
variable_retract = 1.5
variable_fan_speed = 0
variable_idex_mode = ""
variable_idex_toolhead = 0
variable_idex_toolhead_x = 0.0
variable_idex_toolhead_y = 0.0
variable_idex_toolhead_z = 0.0
gcode = 
	RATOS_ECHO MSG="Pausing print..."
	
	
	{% set runout_detected = true if params.RUNOUT|default(false)|lower == 'true' else false %}
	
	
	_LED_PAUSE
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	SAVE_GCODE_STATE NAME=PAUSE_state
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_mode VALUE='"{idex_mode}"'
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={idex_toolhead}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_x VALUE={printer.gcode_move.gcode_position.x|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_y VALUE={printer.gcode_move.gcode_position.y|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_z VALUE={printer.gcode_move.gcode_position.z|float}
	DEBUG_ECHO PREFIX="PAUSE" MSG="idex_mode: {idex_mode}, idex_toolhead: {idex_toolhead}, idex_toolhead_x: {idex_toolhead_x}, idex_toolhead_y: {idex_toolhead_y}, idex_toolhead_z: {idex_toolhead_z}"
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="pause"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if current_z < (max_z - 20.0) %}
	{% set z_safe = 20.0 %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	PAUSE_BASE
	
	
	{% if printer["dual_carriage"] is not defined %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan"].speed|float}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	{% if idex_toolhead == 0 %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t1"].speed|float}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106 S0
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set R = printer["gcode_macro PAUSE"].retract|float %}
	{% if can_extrude %}
	G91
	G1 E-{R} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	{% set pause_print_park_x = printer["gcode_macro RatOS"].pause_print_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].pause_print_park_in %}
	{% if runout_detected %}
	{% set pause_print_park_x = printer["gcode_macro RatOS"].runout_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].runout_park_in %}
	{% endif %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	DEBUG_ECHO PREFIX="PAUSE" MSG="z_speed: {z_speed}, pause_print_park_x: {pause_print_park_x}, pause_print_park_in: {pause_print_park_in}, default_toolhead: {default_toolhead}"
	{% if "xyz" in printer.toolhead.homed_axes %}
	G91
	G1 Z{z_safe} F{z_speed}
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% else %}
	
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	_IDEX_SINGLE X={parking_position}
	{% else %}
	PARK_TOOLHEAD
	{% endif %}
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="pause"
	
	RATOS_ECHO MSG="Print paused"

[gcode_macro RESUME]
description = Resumes the print if the printer is paused.
rename_existing = RESUME_BASE
gcode = 
	
	
	RATOS_ECHO MSG="Resuming print..."
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	
	{% set target_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set target_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if target_idex_mode != '' %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set fan_speed = printer["gcode_macro PAUSE"].fan_speed|float %}
	{% if printer["dual_carriage"] is not defined %}
	M106 S{(fan_speed * 255)}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% else %}
	{% if params.TOOLHEAD is defined %}
	
	{% if params.TOOLHEAD == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% else %}
	{% if printer["gcode_macro PAUSE"].idex_toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	{% if params.TOOLHEAD is defined %}
	_SELECT_TOOL T={params.TOOLHEAD} X=-1 Y=-1 TOOLSHIFT=false
	{% else %}
	_SELECT_TOOL T={printer["gcode_macro PAUSE"].idex_toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	{% endif %}
	
	{% set x = printer["gcode_macro PAUSE"].idex_toolhead_x|float %}
	{% set y = printer["gcode_macro PAUSE"].idex_toolhead_y|float %}
	{% set z = printer["gcode_macro PAUSE"].idex_toolhead_z|float %}
	G1 X{x} Y{y} Z{z} F{speed}
	{% if params.TOOLHEAD is defined %}
	
	SAVE_GCODE_STATE NAME=PAUSE_STATE
	{% endif %}
	{% endif %}
	
	
	{% if params.TOOLHEAD is not defined %}
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% if can_extrude %}
	G91
	G1 E{E} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1 MOVE_SPEED={speed}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	RESUME_BASE
	
	
	_LED_PRINTING
	
	RATOS_ECHO MSG="Print resumed"

[gcode_macro CANCEL_PRINT]
description = Cancels the print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	RATOS_ECHO MSG="Cancelling print..."
	END_PRINT
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	
	CANCEL_PRINT_BASE
	RATOS_ECHO MSG="Print cancelled"

[gcode_macro START_PRINT]
description = Start print procedure, use this in your Slicer.
variable_post_processor_version = 2
variable_is_printing_gcode = False
variable_both_toolheads = True
variable_object_xoffset = 0
variable_first_x = -1
variable_first_y = -1
variable_total_toolshifts = 0
variable_initial_tool = 0
variable_extruder_first_layer_temp = ""
variable_extruder_other_layer_temp = ""
gcode = 
	
	{% if params.EXTRUDER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_TEMP parameter not found.")}
	{% endif %}
	{% if params.EXTRUDER_OTHER_LAYER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_OTHER_LAYER_TEMP parameter not found.")}
	{% endif %}
	{% if params.BED_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. BED_TEMP parameter not found.")}
	{% endif %}
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' and printer["gcode_macro RatOS"].danger_force_allow_auto_center_subject|default(false)|lower != 'true'%}
	
	
	
	
	
	{ action_raise_error("The experimental auto_center_subject feature is not supported in this version of RatOS. Please disable it in the RatOS macro settings.") }
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes and printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% if printer["gcode_macro _VAOC"].is_started|default(true)|lower == 'true' %}
	_VAOC_END
	{% endif %}
	{% endif %}
	
	
	_LED_START_PRINTING
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_USER_START_PRINT { rawparams }
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_probe_stowable = printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% endif %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	{% set X0 = params.X0|default(-1)|float %}
	{% set X1 = params.X1|default(-1)|float %}
	{% set Y0 = params.Y0|default(-1)|float %}
	{% set Y1 = params.Y1|default(-1)|float %}
	{% if first_x == -1 or first_y == -1 %}
	{% set first_x = params.FIRST_X|default(-1)|float %}
	{% set first_y = params.FIRST_Y|default(-1)|float %}
	{% endif %}
	{% set total_toolshifts = params.TOTAL_TOOLSHIFTS|default(0)|int %}
	{% set initial_tool = params.INITIAL_TOOL|default(default_toolhead)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	
	
	
	
	
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(printer.heater_bed.target, true)|float %}
	
	
	{% set total_layer_count = params.TOTAL_LAYER_COUNT|default(0)|int %}
	{% set extruder_first_layer_temp = (params.EXTRUDER_TEMP|default("")).split(",") %}
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL BEACON_CONTACT_START_PRINT_TRUE_ZERO={beacon_contact_start_print_true_zero} BEACON_CONTACT_CALIBRATE_MODEL_ON_TRUE_ZERO={beacon_contact_calibrate_model_on_true_zero}
	{% endif %}
	
	_START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH BED_TEMP={bed_temp}
	
	
	RATOS_ECHO MSG="First print coordinates X:{first_x} Y:{first_y}"
	
	
	{% if params.TOTAL_LAYER_COUNT is not defined %}
	{% set link_url = "https://os.ratrig.com/docs/slicers" %}
	{% set link_text = "RatOS Slicer Configuration" %}
	{% set line_1 = '"Your slicer gcode settings are not up to date._N_Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="Incomplete Slicer Configuration detected" TYPE="warning" MSG={line_1}
	{% endif %}
	
	
	SET_PRINT_STATS_INFO CURRENT_LAYER=1
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE=1
	{% if total_layer_count > 0 %}
	SET_PRINT_STATS_INFO TOTAL_LAYER={total_layer_count}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads %}
	{% set initial_tool = 0 if initial_tool == 1 else 1 %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	{% endif %}
	
	
	{% set both_toolheads = true %}
	{% if total_toolshifts == 0 %}
	{% set both_toolheads = false %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	{% endif %}
	{% if both_toolheads and (idex_mode == "copy" or idex_mode == "mirror") %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Gcode tool changes found. Copy and mirror mode do not support toolchanges.")}
	{% endif %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set both_toolheads = true %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=initial_tool VALUE={initial_tool}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_x VALUE={first_x}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_y VALUE={first_y}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=total_toolshifts VALUE={total_toolshifts}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=both_toolheads VALUE={both_toolheads}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_first_layer_temp VALUE="'{params.EXTRUDER_TEMP}'"
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_other_layer_temp VALUE="'{params.EXTRUDER_OTHER_LAYER_TEMP}'"
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE=0
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set svv = printer.save_variables.variables %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set stepper_x_position_min = printer.fastconfig.settings.stepper_x.position_min|float %}
	{% set stepper_x_position_endstop = printer.fastconfig.settings.stepper_x.position_endstop|float %}
	{% set dual_carriage_position_max = printer.fastconfig.settings.dual_carriage.position_max|float %}
	{% set dual_carriage_position_endstop = printer.fastconfig.settings.dual_carriage.position_endstop|float %}
	{% set x_parking_space = parking_position_t0 - (stepper_x_position_endstop , stepper_x_position_min)|max %}
	{% set dc_parking_space = (dual_carriage_position_endstop , dual_carriage_position_max)|min - parking_position_t1 %}
	{% if svv.idex_xoffset|abs >= (x_parking_space - 0.5) or svv.idex_xoffset|abs >= (dc_parking_space - 0.5) %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Toolhead x-offset is too high for the available parking space. Calibrate your X and DC endstop positions and make sure you stay below 1mm." % (copy_mode_max_width)) }
	{% endif %}
	{% endif %}
	
	
	{% if (idex_mode == "copy" or idex_mode == "mirror") and printer.fastconfig.settings.ratos.enable_gcode_transform %}
	
	{% if params.MIN_X is not defined or params.MAX_X is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Something went wrong! Missing important post processor start print parameter!") }
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE=0
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	
	{% set boundary_box_min_x = params.MIN_X|default(0)|float %}
	{% set boundary_box_max_x = params.MAX_X|default(printable_x_max)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if default_toolhead == 0 %}
	
	{% set boundary_box_max_x = boundary_box_max_x + svv.idex_xoffset %}
	{% else %}
	
	{% set boundary_box_min_x = boundary_box_min_x - svv.idex_xoffset %}
	{% endif %}
	
	{% set center_x = printable_x_max / 2.0 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set object_width = boundary_box_max_x - boundary_box_min_x %}
	{% set copy_mode_max_width = center_x %}
	{% set mirror_mode_max_width = center_x - safe_distance / 2.0 %}
	
	DEBUG_ECHO PREFIX="START_PRINT" MSG="OBJECT_WIDTH: {object_width} BOUNDARY_BOX_MIN_X: {boundary_box_min_x} BOUNDARY_BOX_MAX_X: {boundary_box_max_x} CENTER_X: {center_x} SAFE_DISTANCE: {safe_distance}"
	
	
	{% if idex_mode == "copy" and object_width > copy_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for copy mode! Max supported width is %s mm" % (copy_mode_max_width)) }
	{% endif %}
	{% if idex_mode == "mirror" and object_width > mirror_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for mirror mode! Max supported width is %s mm" % (mirror_mode_max_width)) }
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = (printable_x_max - boundary_box_max_x - boundary_box_min_x) / 2 %}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE={object_xoffset}
	{% endif %}
	
	{% endif %}
	
	
	{% set has_initial_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_toolhead_filament_sensor %}
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% set has_initial_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_bowden_filament_sensor %}
	
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% if printer["dual_carriage"] is defined and both_toolheads %}
	
	{% set has_secondary_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set has_secondary_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_CHAMBER_FILTER_ON AT="before_print_start"
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true' %}
	{% if both_toolheads %}
	RATOS_ECHO MSG="Spool join is not possible if both toolheads are in use!"
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	{% endif %}
	
	
	CLEAR_PAUSE
	{% if printer["gcode_macro RatOS"].force_absolute_position|lower == 'true' %}
	G90
	{% endif %}
	SAVE_GCODE_STATE NAME=start_print_state
	
	
	G21
	
	G90
	
	M82
	_USER_START_PRINT_BEFORE_HOMING { rawparams }
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_BEGIN_BATCH
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_Z_HOP
	
	
	{% if idex_mode != '' and not (printer.fastconfig.settings.beacon is defined and (beacon_contact_start_print_true_zero or beacon_adaptive_heat_soak)) %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	{% if chamber_temp > 0 %}
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED={printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float}
	{% endif %}
	{% endif %}
	_CHAMBER_HEATER_ON START_CHAMBER_TEMP={start_chamber_temp} CHAMBER_TEMP={chamber_temp}
	_USER_START_PRINT_HEAT_CHAMBER { rawparams } CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_START_PRINT_BEFORE_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	RATOS_ECHO MSG="Heating bed..."
	
	M190 S{bed_temp}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_adaptive_heat_soak %}
	_MOVE_TO_SAFE_Z_HOME
	
	G1 Z2.5 F{z_speed}
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK LAYER_QUALITY={beacon_adaptive_heat_soak_layer_quality} MAXIMUM_FIRST_LAYER_DURATION={beacon_adaptive_heat_soak_maximum_first_layer_duration} MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={beacon_adaptive_heat_soak_max_wait}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_BED { rawparams }
	
	
	_START_PRINT_AFTER_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	_USER_START_PRINT_BED_MESH { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_BED_MESH X0={X0} X1={X1} Y0={Y0} Y1={Y1} T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_END_BATCH
	{% endif %}
	
	
	{% if idex_mode == '' %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[initial_tool]|float}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[0]|float}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={extruder_first_layer_temp[1]|float}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_PARK { rawparams }
	
	
	_START_PRINT_PARK
	
	
	RATOS_ECHO MSG="Heating Extruder..."
	{% if idex_mode == '' %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[initial_tool]|float}  MAXIMUM={extruder_first_layer_temp[initial_tool]|float + 5}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[0]|float}  MAXIMUM={extruder_first_layer_temp[0]|float + 5}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder1" MINIMUM={extruder_first_layer_temp[1]|float}  MAXIMUM={extruder_first_layer_temp[1]|float + 5}
	{% endif %}
	{% endif %}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	{% if idex_mode == '' %}
	_LED_PRINTING
	{% else %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	_LED_PRINTING
	{% else %}
	{% if both_toolheads %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	{% if toolchange_standby_temp > -1 %}
	_LED_TOOLHEAD_STANDBY TOOLHEAD={0 if initial_tool == 1 else 1}
	{% else %}
	_LED_PRINTING TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% else %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_EXTRUDER { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_AFTER_HEATING_EXTRUDER X0={X0} X1={X1} Y0={Y0} Y1={Y1} INITIAL_TOOLHEAD={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if idex_mode != '' %}
	{% if not both_toolheads %}
	{% if initial_tool != default_toolhead %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if idex_mode != '' %}
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=standby VALUE=False
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=standby VALUE=False
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if initial_tool == 1 else 'extruder1'} TARGET={toolchange_standby_temp}
	SET_GCODE_VARIABLE MACRO=T{0 if initial_tool == 1 else 1} VARIABLE=standby VALUE=True
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=start_print_state
	
	{% if printer["dual_carriage"] is defined %}
	_SET_IDEX_MODE_OFFSET
	{% endif %}
	
	
	{% if idex_mode != '' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% if idex_mode == "copy" and idex_mode != act_idex_mode %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == "mirror" and idex_mode != act_idex_mode %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={object_xoffset} MOVE=0
	{% endif %}
	{% else %}
	_SELECT_TOOL T={initial_tool} TOOLSHIFT=false
	_SET_TOOLHEAD_OFFSET
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	_SET_EXTRUSION_MODE
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={printer["print_stats"].print_duration}
	{% endif %}
	
	
	_USER_END_START_PRINT { rawparams }
	
	G92 E0
	
	
	_CHAMBER_FILTER_ON AT="after_print_start"
	
	_ALERT_NON_ZERO_Z_OFFSET
	
	RATOS_ECHO MSG="Printing..."

[gcode_macro _START_PRINT_BEFORE_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set is_stowable_probe = true if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' else false %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Pre-heating extruder..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={min_temp}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET={min_temp}
	{% endif %}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	{% endif %}
	{% endif %}
	
	
	{% if not is_stowable_probe %}
	{% if printer["dual_carriage"] is defined and act_t != default_toolhead %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	{% endif %}
	RATOS_ECHO MSG="Heat soaking z probe..."
	_MOVE_TO_SAFE_Z_HOME
	
	G0 Z2 F{z_speed}
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Waiting for extruder to be preheated..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	{% if default_toolhead == 0 %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_Z_HOP
	{% endif %}
	
	
	{% if auto_z_offset_calibration %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	PARK_TOOLHEAD
	_CLEANING_MOVE TOOLHEAD={default_toolhead} AUTOMATED=True
	_SELECT_TOOL T={0 if default_toolhead == 1 else 1} X={parking_position_t0 if default_toolhead == 1 else parking_position_t1} Y=0 TOOLSHIFT=false
	_CLEANING_MOVE TOOLHEAD={0 if default_toolhead == 1 else 1} AUTOMATED=True
	_VAOC_CALIBRATE_Z_OFFSET AUTO_Z_OFFSET=True
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=false
	{% endif %}
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	{% if needs_rehoming %}
	G28 Z
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	_START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE
	{% endif %}
	{% endif %}
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	PROBE PROBE_METHOD=contact SAMPLES=1

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	{% set fuzzy_radius = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_radius|default(0)|float if beacon_contact_start_print_true_zero_fuzzy_position else 0 %}
	
	{% set contact_true_zero_temp_has_been_set = False %}
	
	
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	
	
	
	{% if printer.beacon.last_probe_result|lower == "ok" %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	RATOS_ECHO MSG="Auto calibration nozzle wipe with probe result {last_z_offset}..."
	G0 Z{(0.2 + last_z_offset)} F{z_speed}
	G0 X70 F300
	{% else %}
	RATOS_ECHO MSG="Skipping auto calibration nozzle wipe because probing failed!"
	{% endif %}
	{% elif beacon_contact_wipe_before_true_zero_method == "probe_clean" %}
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	
	{% set contact_true_zero_temp_has_been_set = True %}
	
	
	
	
	
	
	
	
	BEACON_PROBE_CLEAN X=50 Y=10
	{% else %}
	CONSOLE_ECHO TYPE="error" TITLE="Unknown wipe method" MSG="Unknown wipe method '{beacon_contact_wipe_before_true_zero_method}' configured, skipping wipe before beacon true zero."
	{% endif %}
	{% endif %}
	
	
	G0 Z5 F{z_speed}
	_MOVE_TO_SAFE_Z_HOME FUZZY_RADIUS={fuzzy_radius}
	
	
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION
	
	{% if not contact_true_zero_temp_has_been_set %}
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon contact auto calibration..."
	
	{% if beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	
	G0 Z5 F{z_speed}

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION]
gcode = 
	{% set pos = printer.ratos.last_move_to_safe_z_home_position %}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE={pos[0]}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE={pos[1]}

[gcode_macro _START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set first_x = printer["gcode_macro START_PRINT"].first_x|default(-1)|float %}
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2.0 %}
	{% set center_y = printable_y_max / 2.0 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% if printer["dual_carriage"] is defined %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% endif %}
	
	
	{% set X0 = params.X0|default(-1)|int %}
	{% set X1 = params.X1|default(-1)|int %}
	{% set Y0 = params.Y0|default(-1)|int %}
	{% set Y1 = params.Y1|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	
	{% if idex_mode == '' %}
	
	_PRIME
	{% else %}
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	RATOS_ECHO PREFIX="IDEX" MSG="using combined prime offset for IDEX {idex_mode} mode"
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	{% if both_toolheads %}
	{% if initial_toolhead == 0 %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T{initial_toolhead}"
	_SELECT_TOOL T={initial_toolhead} TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	SET_MACRO_TRAVEL_SETTINGS
	
	{% if (X0 > -1 and Y1 > -1) or (first_x > 0 and first_y > 0) %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	{% endif %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	{% set first_z = 1 %}
	{% else %}
	{% set first_z = 3 %}
	{% endif %}
	
	
	{% if idex_mode == "mirror" %}
	{% if first_y >= 0 %}
	G0 Y{first_y} F{speed}
	{% else %}
	G0 Y{Y1} F{speed}
	{% endif %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={initial_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={initial_toolhead} E={printer["gcode_macro RatOS"].toolchange_first_purge|default(50)|float}
	_CLEANING_MOVE TOOLHEAD={initial_toolhead} AUTOMATED=True
	{% endif %}
	{% if first_x >= 0 and first_y >= 0 %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% else %}
	{% set first_x = X0 %}
	{% set first_y = Y0 %}
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'min' %}
	{% set first_x = X0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'max' %}
	{% set first_x = X1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|float <= center_x %}
	{% set first_x = X0 %}
	{% else %}
	{% set first_x = X1 %}
	{% endif %}
	{% endif %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'min' %}
	{% set first_y = Y0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'max' %}
	{% set first_y = Y1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|float <= center_y %}
	{% set first_y = Y0 %}
	{% else %}
	{% set first_y = Y1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	
	
	_LOAD_RATOS_SKEW_PROFILE

[gcode_macro _PRIME]
gcode = 
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	PRIME_BLOB INITIAL_TOOLHEAD={params.INITIAL_TOOLHEAD} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={params.IDEX_MODE} Y1={params.Y1}
	{% else %}
	
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif params.IDEX_MODE == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro END_PRINT]
description = End print procedure, use this in your Slicer.
gcode = 
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SAVE_GCODE_STATE NAME=end_print_state
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = printer["gcode_macro START_PRINT"].object_xoffset|default(0)|float %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(0-object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={(0-object_xoffset)}
	{% endif %}
	{% endif %}
	
	
	_USER_END_PRINT_BEFORE_HEATERS_OFF { rawparams }
	_END_PRINT_BEFORE_HEATERS_OFF
	TURN_OFF_HEATERS
	_USER_END_PRINT_AFTER_HEATERS_OFF { rawparams }
	_END_PRINT_AFTER_HEATERS_OFF
	_USER_END_PRINT_PARK { rawparams }
	_END_PRINT_PARK
	
	
	{% if printer["gcode_macro RatOS"].skew_profile is defined %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined and printer["gcode_macro RatOS"].end_print_motors_off|lower != 'false' %}
	
	M84
	{% endif %}
	
	
	M107
	
	
	BED_MESH_CLEAR
	RATOS_ECHO MSG="Done :)"
	
	
	RESTORE_GCODE_STATE NAME=end_print_state
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	M84
	{% endif %}
	
	
	RESET_NAMED_OFFSET EVENT="end_print"
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_CHAMBER_FILTER_ON AT="print_end"
	_CHAMBER_FILTER_OFF
	
	
	_CHAMBER_HEATER_OFF
	
	_USER_END_PRINT_FINISHED { rawparams }

[gcode_macro _END_PRINT_BEFORE_HEATERS_OFF]
gcode = 
	RATOS_ECHO MSG="Cleaning up..."

[gcode_macro _END_PRINT_AFTER_HEATERS_OFF]
gcode = 
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% set z_hop = printer["gcode_macro RatOS"].end_print_park_z_hop|float %}
	{% set r = printer["gcode_macro RatOS"].end_print_retract_filament|default(4)|float %}
	{% if current_z < (max_z - z_hop) %}
	{% set z_safe = z_hop %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G91
	
	{% if can_extrude %}
	G1 E-2 F3600
	{% endif %}
	
	G0 Z{z_safe} F3600
	
	{% if can_extrude %}
	G1 E-{(r-2)} F3600
	{% endif %}
	
	G90

[gcode_macro _SET_EXTRUSION_MODE]
gcode = 
	
	{% if printer["gcode_macro RatOS"].relative_extrusion|lower == 'true' %}
	M83
	{% else %}
	M82
	{% endif %}

[gcode_macro GENERATE_SHAPER_GRAPHS]
description = Genarates input shaper resonances graphs for analysis. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	{% set hz_per_sec = params.HZ_PER_SEC|default(1)|float %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set copy_mode_offset = printable_x_max / 4.0 %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	_IDEX_SINGLE
	{% endif %}
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	
	
	{% if idex_mode != 'copy' and idex_mode != 'mirror' %}
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	{% endif %}
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Shaper graph"

[gcode_shell_command generate_shaper_graph_x]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-x.sh
timeout = 60.
verbose = True

[gcode_shell_command generate_shaper_graph_y]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-y.sh
timeout = 60.
verbose = True

[gcode_macro MEASURE_COREXY_BELT_TENSION]
description = Generates resonance graph used to ensure belts are equally tensioned. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	_IDEX_SINGLE
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if measure_t1 == false or measure_t0 == false %}
	{action_raise_error("Axis specified. Not supported for belt tension on Y.")}
	{% else %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	G4 P5000
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	PARK_TOOLHEAD
	{% endif %}
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	G1 X{parking_position_t1} F{speed}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	
	
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Belt Tension Graph"

[gcode_shell_command generate_belt_tension_graph]
command = /home/pi/printer_data/config/RatOS/scripts/generate-belt-tension-graph.sh
timeout = 90.
verbose = True

[idle_timeout]
gcode = 
	{% if printer.webhooks.state|lower == 'ready' %}
	{% if printer.pause_resume.is_paused|lower == 'false' %}
	_USER_BEFORE_IDLE_TIMEOUT
	RATOS_ECHO PREFIX="IDLE" MSG="2 hours since last activity. Powering off heaters and motors.."
	TURN_OFF_HEATERS
	M84
	_USER_AFTER_IDLE_TIMEOUT
	{% endif %}
	{% endif %}
timeout = 7200

[temperature_sensor raspberry_pi]
sensor_type = temperature_host

[skew_correction]

[named_offsets]

[input_shaper]

[virtual_sdcard]
path = ~/printer_data/gcodes

[display_status]

[pause_resume]

[force_move]
enable_force_move = True

[respond]

[resonance_generator]

[ratos]
allow_unknown_gcode_generator = True
enable_gcode_transform = True

[exclude_object]

[bed_mesh]
split_delta_z = 0.001
horizontal_move_z = 2
mesh_min = 20,20
mesh_max = 480,480
probe_count = 40,40
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = .2
speed = 600
log_points = False

[fastconfig]

[heater_bed]
heater_pin = heater_bed_heating_pin
sensor_pin = heater_bed_sensor_pin
sensor_type = Generic 3950
min_temp = 0
max_temp = 140
pwm_cycle_time = 0.103
control = pid
pid_kp = 61.987
pid_ki = 1.781
pid_kd = 539.289

[printer]
kinematics = ratos_hybrid_corexy
max_velocity = 800
max_accel = 10000
minimum_cruise_ratio = 0.5
max_z_velocity = 50
max_z_accel = 600
square_corner_velocity = 5

[ratos_hybrid_corexy]
inverted = true

[dual_carriage]
axis = x
safe_distance = 55
position_max = 559.6
position_endstop = 559.6
position_min = 0
step_pin = PF9
dir_pin = dual_carriage_dir_pin
enable_pin = !PG2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t1:PA2

[gcode_macro _SET_IDEX_MODE_OFFSET]
description = "Internal use only. Sets the 'idex_mode' named offset that the active idex mode requires."
gcode = 
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_SET_IDEX_MODE_OFFSET" MSG="idex_mode: {idex_mode}, center_x: {center_x}"
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	SET_NAMED_OFFSET NAME=idex_mode X={(-center_x / 2)}
	{% else %}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% else %}
	{action_raise_error("_SET_IDEX_MODE_OFFSET: Printer not homed")}
	{% endif %}

[gcode_macro IDEX_SINGLE]
gcode = 
	_IDEX_REMAP_TOOLHEADS ENABLE=False
	_IDEX_SINGLE

[gcode_macro _IDEX_SINGLE]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_single"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set init = params.INIT|default(0)|int %}
	{% set new_x = params.X|default(-1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_default_t = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="init: {init}, new_x: {new_x}, idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, act_t: {act_t}"
	
	{% if idex_mode == "copy" or idex_mode == "mirror" or init == 1 %}
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="reset idex_mode offset"
	G1 X{center_x} F{(speed)}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="activate default carriage"
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolheads"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	G90
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position."
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1}
	G1 X{parking_position_default_t} F{speed}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move default toolhead to its new position."
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% if new_x == -1 %}
	{% set new_x = center_x %}
	{% endif %}
	G1 X{new_x} F{speed}
	
	M400
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="X Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set extruder motion queue."
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if default_toolhead==0 else default_toolhead}
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolhead offset."
	_SET_TOOLHEAD_OFFSET
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set input shaper."
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[default_toolhead]|float)} SHAPER_FREQ_Y={(shaper_y_freq[default_toolhead]|float)} SHAPER_TYPE_X={(shaper_x_type[default_toolhead]|lower)} SHAPER_TYPE_Y={(shaper_y_type[default_toolhead]|lower)}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="update Frontend."
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if default_toolhead==0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if default_toolhead==1 else False}
	{% else %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_single"

[gcode_macro IDEX_COPY]
gcode = 
	_IDEX_COPY

[gcode_macro _IDEX_COPY]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_copy"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set y = params.Y|default(-1)|int %}
	{% set dance = params.DANCE|default(1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_COPY" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}, y: {y}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "copy" %}
	{% if idex_mode == "mirror" %}
	{% if y>=0 %}
	G1 X{center_x} Y{y} F{(speed)}
	{% else %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	
	
	{% if idex_mode != "mirror" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance == 1 %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[2]|float)} SHAPER_FREQ_Y={(shaper_y_freq[2]|float)} SHAPER_TYPE_X={(shaper_x_type[2]|lower)} SHAPER_TYPE_Y={(shaper_y_type[2]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_copy"

[gcode_macro IDEX_MIRROR]
gcode = 
	_IDEX_MIRROR

[gcode_macro _IDEX_MIRROR]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_mirror"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set dance = params.DANCE|default(1)|int %}
	{% set priming = params.PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_MIRROR" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "mirror" %}
	
	{% if idex_mode == "copy" %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS MIRROR_PRIMING={params.PRIMING}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=MIRROR
	
	
	{% if idex_mode != "copy" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance and not priming %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[3]|float)} SHAPER_FREQ_Y={(shaper_y_freq[3]|float)} SHAPER_TYPE_X={(shaper_x_type[3]|lower)} SHAPER_TYPE_Y={(shaper_y_type[3]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_mirror"

[gcode_macro _IDEX_SET_TOOLHEADS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set mirror_priming = params.MIRROR_PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position_inactive_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_IDEX_SET_TOOLHEADS" MSG="idex_mode: {idex_mode}, act_t: {act_t}, center_x: {center_x}, mirror_priming: {mirror_priming}"
	
	
	{% if act_t != default_toolhead %}
	_SET_TOOLHEAD_OFFSET FORCE_TOOLHEAD={default_toolhead} MOVE=1
	{% endif %}
	
	{% if mirror_priming %}
	
	
	
	{% if parking_position_t0|abs < parking_position_t1 - printable_x_max %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{printable_x_max + parking_position_t0|abs} F{(speed)}
	{% else %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{0 - (parking_position_t1 - printable_x_max)} F{(speed)}
	{% endif %}
	
	{% else %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1} MODE=PRIMARY
	G1 X{parking_position_inactive_t} F{(speed)}
	
	
	{% if act_t==1 %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{center_x / 2} F{(speed)}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"

[gcode_macro IDEX_PARK]
gcode = 
	
	PARK_TOOLHEAD

[gcode_macro PARK_TOOLHEAD]
gcode = 
	
	{% set idex_mode = 'none' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="PARK_TOOLHEAD" MSG="Parking T{act_t}.."
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set parking_position_inact_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set printable_y_min = printer["gcode_macro RatOS"].printable_y_min|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" and 'xy' in printer.toolhead.homed_axes %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% elif printer.toolhead.position.y|float < printable_y_min %}
	G1 Y{printable_y_min} F{speed}
	{% endif %}
	
	SAVE_GCODE_STATE NAME=_PARK_TOOLHEAD
	G90
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0.5
	
	
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_inact_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	
	SET_VELOCITY_LIMIT ACCEL={printer.toolhead.max_accel} MINIMUM_CRUISE_RATIO=0.5
	M400
	RESTORE_GCODE_STATE NAME=_PARK_TOOLHEAD
	
	{% endif %}

[gcode_macro JOIN_SPOOLS]
gcode = 
	
	{% set spools = params.SPOOLS|default("") %}
	
	{% if spools == "" %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% else %}
	{% if spools != "0,1" and spools != "1,0" %}
	RATOS_ECHO MSG="Wrong spool configuration!"
	RATOS_ECHO MSG="Join Spools = JOIN_SPOOLS SPOOLS=0,1"
	RATOS_ECHO MSG="Deactivate = JOIN_SPOOLS SPOOLS="
	{% else %}
	{% if spools == "0,1" or spools == "1,0" %}
	_IDEX_JOIN_SPOOLS ENABLE=true
	{% else %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_JOIN_SPOOLS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if enable %}
	{% set has_t0_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t1_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t0_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined else false %}
	{% set has_t1_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined else false %}
	{% if (has_t0_toolhead_filament_sensor and has_t1_toolhead_filament_sensor) or (has_t0_bowden_filament_sensor and has_t1_bowden_filament_sensor) %}
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=True
	RATOS_ECHO MSG="Spool joining enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Can not enable spool joining! No filament sensors found."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining deactivated!"
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining is not possible in copy and mirror mode!"
	{% endif %}

[gcode_macro _JOIN_SPOOL]
gcode = 
	
	{% set old_toolhead = params.TOOLHEAD|int %}
	{% set new_toolhead = 0 if old_toolhead == 1 else 1 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set purge_after_load = printer["gcode_macro T%s" % new_toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_JOIN_SPOOL" MSG="toolhead: {new_toolhead}"
	
	{% set has_filament = true %}
	{% set has_new_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% set has_new_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% if has_new_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	{% if has_new_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	
	{% if has_filament %}
	RATOS_ECHO MSG="Joining spools! Please wait for extruder to heat up...."
	
	
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={new_toolhead}
	
	
	_DEACTIVATE_TOOLHEAD TOOLHEAD={old_toolhead}
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set extruder_temp = extruder_first_layer_temp[new_toolhead]|float %}
	{% else %}
	{% set extruder_temp = extruder_other_layer_temp[new_toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if new_toolhead == 0 else 'extruder1'} TARGET={extruder_temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if new_toolhead == 0 else 'extruder1'} MINIMUM={extruder_temp}  MAXIMUM={extruder_temp + 5}
	
	
	{% if purge_after_load > 0 %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_toolhead == 0 else new_toolhead}
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={new_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={new_toolhead} E={purge_after_load}
	_CLEANING_MOVE TOOLHEAD={new_toolhead} AUTOMATED=True
	
	
	SET_DUAL_CARRIAGE CARRIAGE={old_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if old_toolhead == 0 else old_toolhead}
	
	{% endif %}
	
	
	RESUME TOOLHEAD={new_toolhead}
	
	
	_IDEX_JOIN_SPOOLS ENABLE=false
	
	{% else %}
	{ action_raise_error("Spool join failed! No filament found or filament sensor is disabled.") }
	{% endif %}

[gcode_macro REMAP_TOOLHEADS]
gcode = 
	
	{% set toolheads = params.TOOLHEADS|default("") %}
	
	{% if toolheads == "" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% else %}
	{% if toolheads != "0,1" and toolheads != "1,0" %}
	RATOS_ECHO MSG="Wrong toolhead configuration!"
	RATOS_ECHO MSG="Remap = REMAP_TOOLHEADS TOOLHEADS=0,1"
	RATOS_ECHO MSG="Deactivate = REMAP_TOOLHEADS TOOLHEADS="
	{% else %}
	{% if toolheads == "0,1" or toolheads == "1,0" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=true
	_IDEX_SINGLE
	{% else %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_REMAP_TOOLHEADS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	{% if not enable or (idex_mode != "copy" and idex_mode != "mirror") %}
	{% if enable %}
	RATOS_ECHO MSG="Toolhead remapping enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping deactivated!"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE={enable}
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping not possible in copy and mirror mode!"
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	{% endif %}

[gcode_macro SHAPER_CALIBRATE]
rename_existing = SHAPER_CALIBRATE_ORG
gcode = 
	RATOS_ECHO PREFIX="IDEX" MSG="SHAPER_CALIBRATE is useless on IDEX machines. Please use the GENERATE_SHAPER_GRAPHS macro and type the values into `variable_shaper_*_freq` and `variable_shaper_*_type manually`."

[gcode_shell_command generate_shaper_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-shaper-graph.sh
timeout = 120.
verbose = True

[gcode_shell_command generate_tension_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-belt-tension-graph.sh
timeout = 120.
verbose = True

[gcode_macro SET_PRESSURE_ADVANCE]
variable_snyc_toolheads = False
rename_existing = SET_PRESSURE_ADVANCE_BASE
gcode = 
	{% if params.SYNC_TOOLHEADS is defined %}
	{% set snyc_toolheads = true if params.SYNC_TOOLHEADS|default(false)|lower == 'true' else false %}
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=True
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="Syncing toolheads..."
	{% else %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' or snyc_toolheads %}
	{% set advance = params.ADVANCE|default(printer['extruder'].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['extruder'].smooth_time|float)|float %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T0"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T1"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder1' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% else %}
	{% set extruder = 'extruder' if act_t == 0 else 'extruder1' %}
	{% if params.EXTRUDER is defined %}
	{% set extruder = params.EXTRUDER %}
	{% endif %}
	{% if extruder == 'extruder' or extruder == 'extruder1' %}
	{% set advance = params.ADVANCE|default(printer['%s' % extruder].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['%s' % extruder].smooth_time|float)|float %}
	SET_PRESSURE_ADVANCE_BASE EXTRUDER={extruder} ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% if params.EXTRUDER is not defined %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG={"T%s" % act_t}
	{% endif %}
	{% else %}
	SET_PRESSURE_ADVANCE_BASE { rawparams }
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro M106]
rename_existing = M106.1
variable_swap_speed = -1
gcode = 
	
	{% set s = [[params.S|default(255)|int, 255]|min, 0]|max %}
	{% set p = params.P|default(-1)|int %}
	{% set speed = s / 255 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set t = 1 if idex_mode=='primary' else 0 %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(0)|int == 1 else false %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set sync_fans = true %}
	{% endif %}
	
	
	{% if sync_fans and idex_mode != "copy" and idex_mode != "mirror" %}
	
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int %}
	
	
	{% if toolshift_count > total_toolshifts %}
	{% set sync_fans = false %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE=-1
	
	
	{% if p == -1 %}
	
	{% if speed == 0 %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed}
	{% else %}
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE={speed}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={(speed if (t == 0 or sync_fans) else 0)}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={(speed if (t == 1 or sync_fans) else 0)}
	{% endif %}
	{% else %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed if t == p else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed if t == p else 0}
	{% endif %}
	
	
	M106.1 S{s}

[gcode_macro M107]
rename_existing = M107.1
gcode = 
	{% set p = params.P|default(-1)|int %}
	M106 S0 P{p}

[gcode_macro _SELECT_TOOL]
variable_last_timestamp = 0
gcode = 
	{% if params.T is defined %}
	{% set idex_mode = '' %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if "xyz" not in printer.toolhead.homed_axes and (idex_mode == "copy" or idex_mode == "mirror") %}
	_IDEX_SINGLE
	{% set idex_mode = 'reset' %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set new_t = params.T|int %}
	
	
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads and is_printing_gcode %}
	{% set new_t = 0 if new_t == 1 else 1 %}
	{% endif %}
	
	
	{% set toolchange_prepurging_timer = printer["gcode_macro RatOS"].toolchange_prepurging_timer|default(0)|int %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	DEBUG_ECHO PREFIX="_SELECT_TOOL" MSG="act_t: {act_t}, new_t: {new_t}, is_printing_gcode: {is_printing_gcode}, swap_toolheads: {swap_toolheads}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	{% set act_extruder = 'extruder%s' % ('' if new_t == 0 else new_t) %}
	{% if new_t != act_t or printer.toolhead.extruder != act_extruder or idex_mode == 'reset' %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Selecting T{new_t}.."
	
	
	M220 S100
	
	
	
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(1)|int == 1 else false %}
	
	
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set toolshift = false %}
	{% endif %}
	
	
	{% set fan_speed = printer["fan_generic part_fan_t%s" % act_t].speed %}
	
	
	{% set deactivate_toolhead = false %}
	{% if is_printing_gcode %}
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int + 1 %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE={toolshift_count}
	{% if toolshift_count == total_toolshifts %}
	{% set deactivate_toolhead = true %}
	{% endif %}
	{% endif %}
	
	
	{% set needs_wakeup = true if printer["gcode_macro T%s" % new_t].standby|default(false)|lower == 'true' else false %}
	
	
	{% set needs_purging = false %}
	{% set wake_up_purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% if is_printing_gcode and toolchange_prepurging_timer > 0 and wake_up_purge > 0 %}
	{% set new_timestamp = printer["print_stats"].print_duration %}
	{% set elapsed_time = new_timestamp - last_timestamp %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={new_timestamp}
	{% if elapsed_time > toolchange_prepurging_timer %}
	{% set needs_purging = true %}
	{% endif %}
	{% endif %}
	
	
	{% set first_use_purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% if toolshift_count == 1 and first_use_purge > 0 %}
	{% set needs_purging = true %}
	{% endif %}
	
	
	{% if is_printing_gcode and (toolchange_standby_temp > -1 or needs_purging or needs_wakeup) %}
	_TOOLHEAD_STANDBY TOOLHEAD={act_t}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	_TOOLHEAD_WAKEUP TOOLHEAD={new_t} X={new_x} Y={new_y} Z={new_z} FAN_SPEED={fan_speed} TOOLSHIFT_COUNT={toolshift_count}
	{% else %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(false)|lower == 'true' else false %}
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if (new_t == 0 or sync_fans) else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if (new_t == 1 or sync_fans) else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	_TOOLCHANGE T={new_t} X={new_x} Y={new_y} Z={new_z} PARK_T0={park_t0} PARK_T1={park_t1} TOOLSHIFT={toolshift}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[new_t]|float)} SHAPER_FREQ_Y={(shaper_y_freq[new_t]|float)} SHAPER_TYPE_X={(shaper_x_type[new_t]|lower)} SHAPER_TYPE_Y={(shaper_y_type[new_t]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if new_t == 0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if new_t == 1 else False}
	
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% set sanity_check_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if new_t == 0 %}
	{% if printer.toolhead.extruder == 'extruder' %}
	{% if sanity_check_idex_mode == 'primary' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% elif new_t == 1 %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% if sanity_check_idex_mode == 'inactive' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _TOOLHEAD_STANDBY]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Putting toolhead T{toolhead} into standby mode."
	DEBUG_ECHO PREFIX="_TOOLHEAD_STANDBY" MSG="toolhead: {toolhead}, config_z_hop: {config_z_hop}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={toolhead} SYNC=0
	PARK_TOOLHEAD
	
	
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={toolchange_standby_temp}
	{% endif %}
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=True
	{% endif %}
	
	
	_LED_TOOLHEAD_STANDBY TOOLHEAD={toolhead}

[gcode_macro _TOOLHEAD_WAKEUP]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set fan_speed = params.FAN_SPEED|float %}
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift_count = params.TOOLSHIFT_COUNT|default(0)|int %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% if toolshift_count == 1 %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% endif %}
	{% set needs_wakeup = true if printer["gcode_macro T%s" % toolhead].standby|default(false)|lower == 'true' else false %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Waking up toolhead T{toolhead}. Please wait for extruder to heat up..."
	DEBUG_ECHO PREFIX="_TOOLHEAD_WAKEUP" MSG="toolhead: {toolhead}, fan_speed: {fan_speed}, new_x: {new_x}, new_y: {new_y}, new_z: {new_z}, config_z_hop: {config_z_hop}"
	
	
	_LED_TOOLHEAD_WAKEUP TOOLHEAD={toolhead}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={toolhead} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE=1
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if toolhead == 0 else toolhead}
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if needs_wakeup %}
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set temp = extruder_first_layer_temp[toolhead]|float %}
	{% else %}
	{% set temp = extruder_other_layer_temp[toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if toolhead == 0 else 'extruder1'} MINIMUM={temp}  MAXIMUM={temp + 5}
	{% endif %}
	
	
	_LED_PRINTING TOOLHEAD={toolhead}
	
	
	{% if purge > 0 %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={toolhead} E={purge}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	
	
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if toolhead == 1 else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	G92 E0
	G1 E-{e} F{feedrate}
	G92 E0
	
	
	{% if new_x >= 0 and new_y >= 0 %}
	G1 X{new_x} Y{new_y} F{speed}
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={config_z_hop} T={toolhead} SYNC=0
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=False

[gcode_macro _TOOLCHANGE]
variable_toolshift_count = 0
gcode = 
	
	
	{% set new_t = params.T|default(-1)|int %}
	{% set new_x = params.X|default(-1.0)|float %}
	{% set new_y = params.Y|default(-1.0)|float %}
	{% set new_z = params.Z|default(-1.0)|float %}
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(true)|lower == 'true' else false %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T: {new_t}, X: {new_x}, Y: {new_y}, Z: {new_z}, PARK_T0: {park_t0}, PARK_T1: {park_t1}, IS_PRINTING_GCODE: {is_printing_gcode}, TOOLSHIFT: {toolshift}"
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	{% if park_t0 >= 0 and park_t1 >= 0 %}
	{% set parking_position_t0 = park_t0 %}
	{% set parking_position_t1 = park_t1 %}
	{% set parking_position_act_t = park_t0 if act_t == 0 else park_t1 %}
	{% endif %}
	
	
	{% if not is_printing_gcode and not toolshift %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Changing tool to T{new_t} without retracting/extruding or moving the toolheads except for parking."
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	G90
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% if not is_printing_gcode and toolshift and new_x < 0 and new_y < 0 %}
	{% set new_x = center_x %}
	{% set new_y = printer.gcode_move.gcode_position.y|float %}
	{% endif %}
	
	{% if new_x < 0 or new_y < 0 %}
	
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="No new X or Y position given, parking the active toolhead and activating the new toolhead without moving it."
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={new_t}
	
	
	{% if "x" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	{% if is_printing_gcode %}
	_EXTRUDE T={new_t}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	{% if "xyz" not in printer.toolhead.homed_axes %}
	
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	
	
	{% set svv = printer.save_variables.variables %}
	{% if new_t == default_toolhead %}
	{% set new_xoffset = 0 %}
	{% set new_yoffset = 0 %}
	{% set new_zoffset = 0 %}
	{% else %}
	{% set new_xoffset = -svv.idex_xoffset %}
	{% set new_yoffset = -svv.idex_yoffset %}
	{% set new_zoffset = -svv.idex_zoffset %}
	{% endif %}
	
	{% set xoffset_correction = new_xoffset - printer.named_offsets.toolhead_alignment.x %}
	{% set yoffset_correction = new_yoffset - printer.named_offsets.toolhead_alignment.y %}
	{% set zoffset_correction = new_zoffset - printer.named_offsets.toolhead_alignment.z %}
	
	{% if new_t == 0 %}
	
	{% set t0_act_x = parking_position_t0 %}
	{% set t1_act_x = printer.toolhead.position.x|float %}
	{% set t0_new_x = new_x %}
	{% set t1_new_x = parking_position_t1 %}
	{% set t0_distance = t0_new_x - t0_act_x %}
	{% set t1_distance = t1_new_x - t1_act_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T0."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	
	
	G1 X{t0_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x + (t1_new_x - t1_act_x)} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t0_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T0: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% elif new_t == 1 %}
	
	{% set t0_act_x = printer.toolhead.position.x|float %}
	{% set t1_act_x = parking_position_t1 %}
	{% set t0_new_x = parking_position_t0 %}
	{% set t1_new_x = new_x %}
	{% set t0_distance = t0_act_x - t0_new_x %}
	{% set t1_distance = t1_act_x - t1_new_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T1."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x - t1_distance + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t1_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T1: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% endif %}
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	{% endif %}

[gcode_macro _ZHOP_BEFORE_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_hop = params.Z_HOP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_HOP: {z_hop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="COMBINED_ZHOP G1 Z+{z_hop} E-{e} F{speed * 60}"
	G1 Z+{z_hop} E-{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="ZHOP G1 Z+{z_hop} F{speed * 60}"
	G1 Z+{z_hop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="RETRACT G1 E-{e} F{feedrate}"
	G1 E-{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _ZDROP_AFTER_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_drop = params.Z_DROP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_DROP: {z_drop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="COMBINED_ZDROP G1 Z-{z_drop} E{e} F{speed * 60}"
	G1 Z-{z_drop} E{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="ZDROP G1 Z-{z_drop} F{speed * 60}"
	G1 Z-{z_drop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="EXTRUDE G1 E{e} F{feedrate}"
	G1 E{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _EXTRUDE]
gcode = 
	
	{% set t = params.T|int %}
	
	
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	
	DEBUG_ECHO PREFIX="_EXTRUDE" MSG="G1 E{e} F{feedrate * 60}"
	
	
	G91
	M82
	G92 E0
	G1 E{e} F{feedrate * 60}
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _DEACTIVATE_TOOLHEAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_DEACTIVATE_TOOLHEAD" MSG="TOOLHEAD {toolhead}"
	
	
	{% if toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% endif %}
	
	
	M106.1 S0
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={toolhead}

[delayed_gcode _INIT_TOOLHEADS]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	_IDEX_SINGLE INIT=1
	
	
	{% if printer.fastconfig.settings.dual_carriage.safe_distance is defined %}
	{% if printer.fastconfig.settings.dual_carriage.safe_distance|float < 50 %}
	{ action_emergency_stop("Dual carriage safe_distance seems to be too low!") }
	{% endif %}
	{% else %}
	{ action_emergency_stop("Dual carriage safe_distance not defined!") }
	{% endif %}

[gcode_macro _SET_TOOLHEAD_OFFSET]
description = "Internal use only. Sets the toolhead_alignment offset (and hotend_thermal_expansion offset when configured) for the active/dominant toolhead."
gcode = 
	
	{% set move = params.MOVE|default(0)|int %}
	{% set force_toolhead = params.FORCE_TOOLHEAD|default(-1)|int %}
	
	
	{% if params.T is defined %}
	CONSOLE_ECHO TYPE="error" MSG="_SET_TOOLHEAD_OFFSET called with deprectated T parameter, which is ignored."
	{';$_SET_TOOLHEAD_OFFSET_ignoring_TOOLHEAD_parameter'}
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="active/dominant toolhead: {toolhead}, MOVE: {move}, FORCE_TOOLHEAD: {force_toolhead}"
	
	
	{% if force_toolhead >= 0 %}
	{% set toolhead = force_toolhead %}
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="FORCE_TOOLHEAD applied, using TOOLHEAD: {toolhead}"
	{% endif %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set move = 0 %}
	{% endif %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|int %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X=0 Y=0 MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z=0 MOVE={move} SPEED={z_speed}
	{% else %}
	{% set svv = printer.save_variables.variables %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X={(-svv.idex_xoffset)} Y={(-svv.idex_yoffset)} MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-svv.idex_zoffset)} MOVE={move} SPEED={z_speed}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}

[gcode_macro TOOLSHIFT_CONFIG]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={params.SPEED|default(300)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={params.ACCEL|default(5000)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_retraction VALUE={params.RETRACT|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_extrusion VALUE={params.EXTRUDE|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_feedrate VALUE={params.FEEDRATE|default(7200)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={params.Z_HOP|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zspeed VALUE={params.Z_SPEED|default(25)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_combined_zhop VALUE={true if params.COMBINED_ZHOP|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_sync_fans VALUE={true if params.SYNC_FANS|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_prepurging_timer VALUE={params.AUTO_PURGE_TIME|default(0)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_purge VALUE={params.PURGE|default(25)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_standby_temp VALUE={params.STANDBY_TEMP|default(-1)|float}

[gcode_macro CALCULATE_DC_ENDSTOP]
description = "DEPRECATED: This macro has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."
gcode = 
	CONSOLE_ECHO TITLE="CALCULATE_DC_ENDSTOP has been deprecated" TYPE="error" MSG="The CALCULATE_DC_ENDSTOP has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."

[gcode_macro _VAOC]
variable_is_fixed = True
variable_is_started = False
variable_is_started_at_temp = False
variable_additional_safe_distance = 50
variable_safe_z = 30
variable_auto_z_offset_calibration = True
variable_enable_camera_cooling = True
variable_camera_cooling_fan_speed = 0.3
variable_camera_cooling_temperature = 50
variable_toolchange_travel_speed = 300
variable_toolchange_travel_accel = 5000
variable_adjusting_secondary_toolhead_focus_adjusts_zoffset = False
variable_cache_toolchange_travel_speed = 300
variable_cache_toolchange_travel_accel = 5000
variable_cache_toolchange_zhop = 1.0
variable_t0_toolhead_sensor_enabled = 0
variable_t1_toolhead_sensor_enabled = 0
variable_t0_bowden_sensor_enabled = 0
variable_t1_bowden_sensor_enabled = 0
variable_loaded_skew_profile = ""
variable_gcode_z_offset = 0.0
variable_start_x_offset = 0.0
variable_start_y_offset = 0.0
gcode = 
	_ECHO_VAOC_VARS
variable_expected_camera_x_position = 212.5
variable_expected_camera_y_position = 530.5

[gcode_macro _VAOC_START]
description = Called from the front end. If T0_TEMP, T1_TEMP and BED_TEMP parameter are specified, VAOC calibration will start under real conditions at printing temp.
gcode = 
	
	{% set t0_temp = params.T0_TEMP|default(0)|int %}
	{% set t1_temp = params.T1_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(0)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro SKEW_PROFILE"].loaded_profile|default("") %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=loaded_skew_profile VALUE='"{loaded_skew_profile}"'
	
	
	{% if t0_temp > 0 and t1_temp > 0 and bed_temp > 0 %}
	
	
	{% if not is_fixed %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("VAOC calibration at temp works only with a fixed installed VAOC device.") }
	{% endif %}
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE=0
	{% endif %}
	
	
	START_PRINT EXTRUDER_TEMP={t0_temp},{t1_temp} EXTRUDER_OTHER_LAYER_TEMP={t0_temp},{t1_temp} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp} INITIAL_TOOL=0 TOTAL_LAYER_COUNT=1 X0={(printable_x_max / 2 - 10)} Y0={(printable_y_max / 2 - 10)} X1={(printable_x_max / 2 + 10)} Y1={(printable_y_max / 2 + 10)} TOTAL_TOOLSHIFTS=1 FIRST_X={printable_x_max / 2} FIRST_Y={printable_y_max / 2} MIN_X={(printable_x_max / 2 - 10)} MAX_X={(printable_x_max / 2 + 10)} USED_TOOLS=0,1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=True
	
	{% endif %}
	
	
	_START_VAOC

[gcode_macro _START_VAOC]
description = Called from _VAOC_START. Do not call it manually.
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(printable_x_max/2)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(printable_y_max/2)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	DEBUG_ECHO PREFIX="VAOC_START" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, zcontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_x_offset VALUE={svv.idex_xoffset|default(0.0)|float}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_y_offset VALUE={svv.idex_yoffset|default(0.0)|float}
	
	
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_SAFE_Z_HEIGHT
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_speed VALUE={printer["gcode_macro RatOS"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_accel VALUE={printer["gcode_macro RatOS"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_zhop VALUE={printer["gcode_macro RatOS"].toolchange_zhop|float}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE=0
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"START X_REFERENCE:%.6f Y_REFERENCE:%.6f Z_REFERENCE:%.6f PARK_T0:%.6f PARK_T1:%.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, parking_position_t0, parking_position_t1)}
	
	
	_LED_VAOC_ON
	
	
	
	
	
	
	
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=gcode_z_offset VALUE={printer.gcode_move.homing_origin.z}
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z=0
	
	
	MAYBE_HOME
	M400
	
	
	_LOAD_RATOS_SKEW_PROFILE
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	IDEX_SINGLE
	{% endif %}
	
	
	
	SAVE_GCODE_STATE NAME=vaoc_state
	
	
	RESET_NAMED_OFFSET EVENT=reset_all
	
	
	{% if is_fixed %}
	_SELECT_TOOL T=0 TOOLSHIFT=false
	{% if default_toolhead == 0 %}
	G1 X{idex_xcontrolpoint} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint + safe_distance + additional_safe_distance} F{speed}
	{% else %}
	G1 X{idex_xcontrolpoint - safe_distance - additional_safe_distance} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint} F{speed}
	{% endif %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	{% else %}
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	G1 X{idex_xcontrolpoint} F{speed}
	G1 Y{idex_ycontrolpoint} F{speed}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	
	
	_SELECT_TOOL T={default_toolhead} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	{% if not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={default_toolhead}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=True

[gcode_macro _VAOC_END]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_y = printable_y_max / 2 %}
	{% set saved_gcode_z_offset = printer["gcode_macro _VAOC"].gcode_z_offset|default(0.0)|float %}
	
	DEBUG_ECHO PREFIX="_VAOC_END" MSG="printable_y_max: {printable_y_max}, center_y: {center_y}, safe_z: {safe_z}"
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% set x_offset_change = svv.idex_xoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_x_offset|default(0.0)|float %}
	{% set y_offset_change = svv.idex_yoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_y_offset|default(0.0)|float %}
	{% set offset_change_norm = (x_offset_change ** 2 + y_offset_change ** 2) ** 0.5 %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="VAOC calibration changed the relative XY offset between T0 and T1 by {offset_change_norm|round(3)} mm (ΔX: {x_offset_change|round(3)}, ΔY: {y_offset_change|round(3)})"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	G1 Y{center_y} F{speed}
	
	
	_IDEX_SINGLE INIT=1
	
	
	_LED_VAOC_OFF
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={printer["gcode_macro _VAOC"].cache_toolchange_zhop|float}
	
	
	{% if printer["gcode_macro _VAOC"].is_started_at_temp|default(true)|lower == 'true' %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_bowden_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_bowden_sensor_enabled|int}
	{% endif %}
	{% endif %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro _VAOC"].loaded_skew_profile|default("") %}
	{% if loaded_skew_profile != "" %}
	SKEW_PROFILE LOAD={loaded_skew_profile}
	{% else %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=vaoc_state
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z={saved_gcode_z_offset}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False

[gcode_macro _VAOC_LOAD_TOOL]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set auto_temp_offset = true if params.AUTO_TEMP_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set toolhead_zoffset = svv.idex_zoffset|default(0)|float %}
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move T%s to control point: X%.6f Y%.6f Z%.6f IS_FIXED=%s"' % (t, idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, is_fixed)}
	
	
	{% if not auto_temp_offset and not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={t}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	{% set current_z = printer.toolhead.position.z|float %}
	{% set lowest_toolhead_z = [current_z, current_z - toolhead_zoffset]|min %}
	{% if lowest_toolhead_z < safe_z %}
	G1 Z{[safe_z, safe_z + toolhead_zoffset]|max} F{z_speed}
	{% else %}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	{% endif %}
	
	
	_SELECT_TOOL T={t} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_SET_CAMERA_COOLING]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	
	
	{% set enable_camera_cooling = true if printer["gcode_macro _VAOC"].enable_camera_cooling|default(true)|lower == 'true' else false %}
	{% set camera_cooling_temperature = printer["gcode_macro _VAOC"].camera_cooling_temperature|float %}
	{% set camera_cooling_fan_speed = printer["gcode_macro _VAOC"].camera_cooling_fan_speed|float %}
	
	
	{% if printer.heater_bed.temperature >= camera_cooling_temperature and enable_camera_cooling %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={camera_cooling_fan_speed if t == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={camera_cooling_fan_speed if t == 1 else 0}
	
	
	M106.1 S{camera_cooling_fan_speed}
	
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	{% endif %}

[gcode_macro _VAOC_SET_TOOL]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="_VAOC_SET_TOOL" MSG="IDEX_MODE: {idex_mode}, TOOLHEAD: {toolhead}"
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	{% set x = printer.gcode_move.gcode_position.x|float %}
	{% set y = printer.gcode_move.gcode_position.y|float %}
	{% set z = printer.gcode_move.gcode_position.z|float %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE={x}
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE={y}
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE={z}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Control point was set: X%.6f Y%.6f Z%.6f"' % (x, y, z)}
	
	{% else %}
	
	
	
	{% set move_diff_x = printer.gcode_move.gcode_position.x|float - svv.idex_xcontrolpoint|float %}
	{% set move_diff_y = printer.gcode_move.gcode_position.y|float - svv.idex_ycontrolpoint|float %}
	{% set move_diff_z = printer.gcode_move.gcode_position.z|float - svv.idex_zcontrolpoint|float %}
	
	
	{% set new_x_offset = svv.idex_xoffset - move_diff_x %}
	{% set new_y_offset = svv.idex_yoffset - move_diff_y %}
	{% set new_z_offset = svv.idex_zoffset - move_diff_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE={new_x_offset}
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE={new_y_offset}
	
	{% set z_focus_msg = "" %}
	{% if move_diff_z|abs > 1e-6 %}
	{% if printer["gcode_macro _VAOC"].adjusting_secondary_toolhead_focus_adjusts_zoffset|default(false)|lower == 'true' %}
	{% set z_focus_msg = " (Z offset adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={new_z_offset}
	{% else %}
	{% set z_focus_msg = " (Z offset not adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	{% set new_z_offset = svv.idex_zoffset %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset was set: X%.6f Y%.6f Z%.6f%s"' % (toolhead, new_x_offset, new_y_offset, new_z_offset, z_focus_msg)}
	
	{% endif %}

[gcode_macro _VAOC_MOVE]
gcode = 
	
	{% set x = params.X|default(0)|float %}
	{% set y = params.Y|default(0)|float %}
	{% set z = params.Z|default(0)|float %}
	
	
	G91
	{% if z != 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 Z%.6f F300"' % (z)}
	G1 Z{z} F300
	
	{% else %}
	{% if x <=2 and y <=2 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 X%.6f Y%.6f F18000"' % (x, y)}
	G1 X{x} Y{y} F18000
	{% endif %}
	{% endif %}
	G90

[gcode_macro _VAOC_CALIBRATE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	{% if printer["z_offset_probe"] is defined and is_started %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	
	{% if auto_z_offset %}
	_START_VAOC AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_END
	{% else %}
	_VAOC_LOAD_TOOL T={default_toolhead}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	{% endif %}
	
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_Z_OFFSET
	
	{% endif %}

[gcode_macro _VAOC_PROBE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}
	{% if not auto_z_offset %}
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	{% endif %}
	M400
	_VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT

[gcode_macro _VAOC_Z_OFFSET_PROBE_CURRENT_POSITION]
gcode = 
	
	Z_OFFSET_PROBE PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_DROP=1 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median

[gcode_macro _VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT]
gcode = 
	{% if printer["z_offset_probe"] is defined %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE={last_z}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Z-offset control point set:: %.6f"' % last_z}
	
	{% else %}
	
	
	
	{% set z = svv.idex_zoffsetcontrolpoint|float - last_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={z}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-z)}
	
	
	G0 Z{svv.idex_zcontrolpoint|float} F{z_speed}
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset set: Z %.6f"' % (t, z)}
	
	{% endif %}
	
	{% endif %}

[gcode_macro _VAOC_ECHO_Z_OFFSET]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s toolhead z-offset %.6f"' % (1 if default_toolhead == 0 else 0, svv.idex_zoffset)}
	{% if svv.idex_zoffset|abs < 0.02 %}
	CONSOLE_ECHO TITLE={'"Perfect toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="You have a perfect toolhead z-offset!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.02 and svv.idex_zoffset|abs < 0.05 %}
	CONSOLE_ECHO TITLE={'"Good toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is good!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.05 and svv.idex_zoffset|abs < 0.1 %}
	CONSOLE_ECHO TITLE={'"High toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset could be better._N_Use minimum 0.3mm first layer height for copy and mirror mode prints." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.1 and svv.idex_zoffset|abs < 0.2 %}
	CONSOLE_ECHO TITLE={'"Bad toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is bad._N_Copy and mirror mode prints are not recommended with it." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.2 %}
	CONSOLE_ECHO TITLE={'"Unacceptable toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is unacceptable._N_Do not print in copy and mirror mode with it." TYPE="alert"
	{% endif %}
	RATOS_ECHO PREFIX="VAOC" MSG="Toolhead z-offset calibration done!"

[gcode_macro _VAOC_CALIBRATE_TEMP_OFFSET]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if is_fixed and is_started and printer["z_offset_probe"] is defined and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	_VAOC_LOAD_TOOL T={default_toolhead} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_NOZZLE_TEMP_OFFSETS
	
	{% endif %}

[gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET=0
	
	
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	M400

[gcode_macro _VAOC_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(150)|float %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Probing with nozzle temperature {temp}°C..."
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	
	
	G0 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _VAOC_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set msg = '"T0 expansion coefficient %.6fmm_N_T1 expansion coefficient %.6fmm"' % (svv.nozzle_expansion_coefficient_t0, svv.nozzle_expansion_coefficient_t1) %}
	CONSOLE_ECHO TITLE="Nozzle expansion coefficients:" MSG={msg} TYPE="success"

[gcode_macro _VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - expected_camera_x_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC x-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_xcontrolpoint, expected_camera_x_position)) }
	{% endif %}
	{% if (idex_ycontrolpoint - expected_camera_y_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC y-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_ycontrolpoint, expected_camera_y_position)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - printer.gcode_move.gcode_position.x|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected y-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_xcontrolpoint, printer.gcode_move.gcode_position.x|float)) }
	{% endif %}
	{% if (idex_ycontrolpoint - printer.gcode_move.gcode_position.y|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected x-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_ycontrolpoint, printer.gcode_move.gcode_position.y|float)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_SAFE_Z_HEIGHT]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set idex_zoffsetcontrolpoint = svv.idex_zoffsetcontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_SAFE_Z_HEIGHT" MSG={'"idex_zcontrolpoint: %.6f, idex_zoffsetcontrolpoint: %.6f"' % (idex_zcontrolpoint, idex_zoffsetcontrolpoint)}
	
	{% if safe_z < idex_zcontrolpoint + 2 or safe_z < idex_zoffsetcontrolpoint + 2 %}
	{action_raise_error("VAOC safe_z value (%.3f) is too low, it must be higher than %.3f" % (safe_z, [idex_zoffsetcontrolpoint + 2, idex_zcontrolpoint + 2]|max))}
	{% endif %}

[gcode_macro _VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED]
gcode = 
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T0. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T1. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_RESET]
gcode = 
	DEBUG_ECHO PREFIX="_VAOC_RESET" MSG="running template-emitted _VAOC_RESET macro"
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE=212.5
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE=530.5
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE=10
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE=0
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE=0.0
	
	RESET_DC_ENDSTOP_CONFIGURATION
	RESET_Y_MAX_ADJUSTMENT
	
	
	CONSOLE_ECHO TITLE="VAOC Configuration Reset" MSG="VAOC configuration has been reset. You must RESTART klipper for the changes to take effect,_N_then re-calibrate VAOC."

[gcode_macro _ECHO_VAOC_VARS]
description = Echo VAOC variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro _VAOC"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro _VAOC_SWITCH_LED]
gcode = 
	{% if params.STATE|default(0)|int == 1 %}
	_LED_VAOC_ON
	{% else %}
	_LED_VAOC_OFF
	{% endif %}

[gcode_macro Z_PROBE_TEST_T0]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T0
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST_T1]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T1
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	
	
	_VAOC_Z_PROBE_TEST_EVALUATE
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro _VAOC_Z_PROBE_LOOP]
gcode = 
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_SHAKE_IT
	_VAOC_START

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if primary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T0. Retried {primary_retries} time(s)."
	{% endif %}
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	
	{% if (primary_range - secondary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 is drifting significantly more than T1."
	{% endif %}
	{% if (secondary_range - primary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 is drifting significantly more than T0."
	{% endif %}
	
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T0]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T1]
gcode = 
	
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _SHAKE_IT]
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	_Z_HOP
	{% for i in range(3) %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 + 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 + 1}
	{% endfor %}
	{% for i in range(2) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 + 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 + 50}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 1}
	{% endfor %}
	{% endfor %}

[gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 retries updated: {new_retries}"

[gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 retries updated: {new_retries}"

[gcode_macro _CLEAR_PRIMARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _CLEAR_SECONDARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _VAOC_TEST_Z_OFFSET]
gcode = 
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}

[delayed_gcode _IDEX_INIT]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	VERIFY_HYBRID_INVERTED

[gcode_macro Z_TILT_ADJUST]
rename_existing = Z_TILT_ADJUST_ORIG
gcode = 
	
	{% set beacon_contact_z_tilt_adjust_samples = printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust_samples|default(2)|int %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(true)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	_IDEX_SINGLE
	
	_SELECT_TOOL T={printer["gcode_macro RatOS"].default_toolhead|default(0)|int} TOOLSHIFT=false
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_tilt_adjust %}
	Z_TILT_ADJUST_ORIG PROBE_METHOD=contact SAMPLES={beacon_contact_z_tilt_adjust_samples}
	{% else %}
	Z_TILT_ADJUST_ORIG
	{% endif %}
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if idex_mode == "copy" %}
	_IDEX_COPY
	{% elif idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[stepper_x]
position_max = 500
position_endstop = -59.6
position_min = -59.6
step_pin = PF13
dir_pin = x_dir_pin
enable_pin = !PF14
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t0:PA2

[stepper_y]
position_max = 533.65
position_min = -14.35
position_endstop = -14.35
step_pin = PG0
dir_pin = !y_dir_pin
enable_pin = !PF15
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = PG9

[stepper_z]
position_max = 500
position_min = -7
step_pin = PC13
dir_pin = !z0_dir_pin
enable_pin = !PF1
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4
homing_speed = 10
endstop_pin = probe:z_virtual_endstop

[z_tilt]
z_positions = 
	0,0
	250,500
	500,0
points = 
	20, 10
	480, 230
	20, 450
horizontal_move_z = 20
retries = 10
retry_tolerance = 0.02
speed = 600

[extruder]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t0:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t0:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t0:PD3
dir_pin = toolboard_t0:e_dir_pin
enable_pin = !toolboard_t0:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[firmware_retraction]
retract_speed = 60
unretract_extra_length = 0
unretract_speed = 60
retract_length = 0.2

[extruder1]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t1:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t1:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t1:PD3
dir_pin = toolboard_t1:e_dir_pin
enable_pin = !toolboard_t1:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[resonance_tester]
accel_chip_x = lis2dw toolboard_t0
accel_chip_y = lis2dw toolboard_t0
probe_points = 
	250,250,20

[tmc5160 stepper_x]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC4
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 dual_carriage]
stealthchop_threshold = 0
interpolate = True
cs_pin = PF2
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y]
stealthchop_threshold = 0
interpolate = True
cs_pin = PD11
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y1]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC7
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[stepper_y1]
step_pin = PG4
dir_pin = y1_dir_pin
enable_pin = !PA2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46

[tmc2209 stepper_z]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE4
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[tmc2209 stepper_z1]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE1
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z1]
step_pin = PE2
dir_pin = !z1_dir_pin
enable_pin = !PD4
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 stepper_z2]
stealthchop_threshold = 0
interpolate = True
uart_pin = PD3
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z2]
step_pin = PE6
dir_pin = !z2_dir_pin
enable_pin = !PE0
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 extruder]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t0:PB3
run_current = 0.707
sense_resistor = 0.11

[tmc2209 extruder1]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t1:PB3
run_current = 0.707
sense_resistor = 0.11

[beacon]
serial = /dev/beacon
x_offset = 0
y_offset = 27.5
mesh_main_direction = x
mesh_runs = 1
mesh_cluster_size = 0
speed = 15.
lift_speed = 80.
contact_max_hotend_temperature = 275
contact_mesh_min = 20,20
contact_mesh_max = 480,480

[beacon_user_z_offset]

[beacon_mesh]

[beacon_true_zero_correction]

[beacon_adaptive_heat_soak]

[delayed_gcode _BEACON_INIT]
initial_duration = 1
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	_BEACON_MESH_INIT
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_coefficient_multiplier
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_applied_offset
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=beacon_saved_runtime_offset
	{% if printer["gcode_macro RatOS"].beacon_contact_expansion_multiplier is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_contact_expansion_multiplier is no longer used, please remove it from your config file."
	{% endif %}
	{% if printer["gcode_macro RatOS"].beacon_scan_compensation_resolution is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_scan_compensation_resolution is no longer used, please remove it from your config file."
	{% endif %}

[gcode_macro BEACON_RATOS_CALIBRATION]
gcode = 
	RATOS_ECHO MSG="Did you mean BEACON_RATOS_CALIBRATE?"

[gcode_macro BEACON_RATOS_CALIBRATE]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	BEACON_INITIAL_CALIBRATION _AUTOMATED=True
	
	{% if beacon_contact_start_print_true_zero %}
	BEACON_POKE_TEST _AUTOMATED=True
	_BEACON_CHECK_POKE
	{% if printer["dual_carriage"] is not defined %}
	BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET _AUTOMATED=True
	{% endif %}
	{% endif %}
	
	{% set already_heated = False %}
	
	
	{% if beacon_contact_start_print_true_zero and beacon_scan_compensation_enable %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% set already_heated = True %}
	{% endif %}
	
	
	BEACON_FINAL_CALIBRATION _AUTOMATED=True _AUTOMATED_ALREADY_HEATED={already_heated} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	{% if beacon_contact_start_print_true_zero %}
	{% if printer["dual_carriage"] is not defined %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	_BEACON_ECHO_POKE
	{% endif %}
	RATOS_ECHO MSG="Beacon calibration finished!"
	
	
	_LED_BEACON_CALIBRATION_END
	
	
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG

[gcode_macro BEACON_INITIAL_CALIBRATION]
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Initial beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro BEACON_FINAL_CALIBRATION]
description = Runs BEACON_AUTO_CALIBRATE after heating the bed and chamber to specified temperatures. This creates a beacon model under reference conditions for future use.
	This macro will skip calibration if both the beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero settings are enabled, because a new
	model will be calibrated automatically at the start of each print. Use FORCE=True to override this check.
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set already_heated = true if params._AUTOMATED_ALREADY_HEATED|default(false)|lower == 'true' else false %}
	{% set force = params.FORCE|default('false')|lower in ('1', 'true', 'yes') %}
	
	
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default('false')|lower == "true" %}
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero and not force %}
	RATOS_ECHO MSG="BEACON_FINAL_CALIBRATION skipped, not needed because beacon_contact_calibrate_model_on_true_zero is enabled. Use FORCE=True to override."
	{% else %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	{% if chamber_temp > 0 and not already_heated %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	{% if not already_heated %}
	
	G0 Z2.5 F{z_hop_speed}
	
	
	RATOS_ECHO MSG="Waiting for calibration temperature..."
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	{% if beacon_adaptive_heat_soak %}
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,3600]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_Z_HOP
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Final beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	{% endif %}

[gcode_macro BEACON_POKE_TEST]
variable_poke_result_1 = -1
variable_poke_result_2 = -1
variable_poke_result_3 = -1
variable_poke_result_4 = -1
variable_poke_result_5 = -1
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_1 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_2 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_3 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_4 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_5 VALUE=-1
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G0 Z5 F{z_hop_speed}
	
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=1
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=2
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=3
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=4
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=5
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Beacon poke test finished!"
	{% if not automated %}
	_BEACON_ECHO_POKE
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro _BEACON_PROBE_POKE]
gcode = 
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	BEACON_POKE speed=3 top=5 bottom={poke_bottom}
	BEACON_QUERY

[gcode_macro _BEACON_STORE_POKE]
gcode = 
	
	{% set i = params.I|default(1)|int %}
	
	
	{% set last_z = printer.beacon.last_poke_result|default(0)|float %}
	
	
	{% if printer.beacon.last_poke_result|lower != "none" %}
	{% if printer.beacon.last_poke_result.error == 0 %}
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE={"poke_result_%s" % i} VALUE={printer.beacon.last_poke_result.latency}
	{% endif %}
	{% endif %}

[gcode_macro _BEACON_CHECK_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% if p1 == -1 or p2 == -1 or p3 == -1 or p4 == -1 or p5 == -1 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test error!") }
	{% endif %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	{% if avg > 6 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test failed!") }
	{% endif %}

[gcode_macro _BEACON_ECHO_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	
	
	{% if avg <= 1 %}
	{% set type = "success" %}
	{% set note = "Extremely low noise, rarely achieved" %}
	{% elif avg > 1 and avg <= 4 %}
	{% set type = "info" %}
	{% set note = "Excellent performance for a typical printer" %}
	{% elif avg > 4 and avg <= 8 %}
	{% set type = "warning" %}
	{% set note = "Acceptable performance, machine may have considerable cyclic axis noise" %}
	{% elif avg > 8 and avg <= 11 %}
	{% set type = "alert" %}
	{% set note = "Not ideal, may want to verify proper mounting or use thinner stackups" %}
	{% elif avg > 11 %}
	{% set type = "alert" %}
	{% set note = "Reason for concern, present setup may be risky to continue with" %}
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon poke test result:" TYPE={type} MSG={'"Average latency: %.2f_N_%s"' % (avg, note)}

[gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Nozzle temperature offset calibration..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET=0
	
	
	{% if not automated %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing with nozzle temperature {temp}°C..."
	PROBE PROBE_METHOD=contact PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median
	BEACON_QUERY
	
	
	G0 Z5 F{z_speed}

[gcode_macro _BEACON_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer.beacon.last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{default_toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% if default_toolhead == 0 %}
	CONSOLE_ECHO TYPE="info" MSG={'"T0 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t0}
	{% else %}
	CONSOLE_ECHO TYPE="info" MSG={'"T1 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t1}
	{% endif %}

[gcode_macro _BEACON_SET_NOZZLE_TEMP_OFFSET]
description = "Set the thermal expansion z offset for the active toolhead based on the current extruder target temperature and thermal expansion coefficient."
gcode = 
	{% if params.RESET is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The RESET parameter is no longer supported and has no effect."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% if params.TOOLHEAD is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The TOOLHEAD parameter is no longer supported and has no effect. The macro now automatically determines the current toolhead."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	{% if beacon_contact_expansion_compensation %}
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set nozzle_expansion_coefficient_t0 = svv.nozzle_expansion_coefficient_t0|default(0)|float %}
	{% if printer["dual_carriage"] is defined %}
	{% set nozzle_expansion_coefficient_t1 = svv.nozzle_expansion_coefficient_t1|default(0)|float %}
	{% endif %}
	
	
	{% set temp = printer['extruder' if toolhead == 0 else 'extruder1'].target|float %}
	
	
	{% set temp_delta = temp - beacon_contact_true_zero_temp %}
	{% set expansion_coefficient = nozzle_expansion_coefficient_t0 if toolhead == 0 else nozzle_expansion_coefficient_t1 %}
	{% set expansion_offset = temp_delta * (expansion_coefficient / 100) %}
	
	
	SET_NAMED_OFFSET NAME=hotend_thermal_expansion Z={expansion_offset} MOVE=1 MOVE_SPEED={z_speed}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG={'"Nozzle expansion offset of %.6fmm applied to T%s"' % (expansion_offset, toolhead)}
	DEBUG_ECHO PREFIX="_BEACON_SET_NOZZLE_TEMP_OFFSET" MSG="toolhead: {toolhead}, coefficient: {expansion_coefficient|round(6)}, temp_delta: {temp_delta|round(1)},  expansion_offset: {expansion_offset|round(6)}"
	
	{% endif %}

[gcode_macro BEACON_MEASURE_BEACON_OFFSET]
variable_needs_compensation = False
variable_reference_z = 0.0
variable_front = 0.0
variable_front_left = 0.0
variable_front_right = 0.0
variable_back = 0.0
variable_back_left = 0.0
variable_back_right = 0.0
variable_right = 0.0
variable_left = 0.0
variable_margin_x = 40
variable_margin_y = 40
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=False
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Measure beacon offset..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="center"
	
	
	G0 X{margin_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_left"
	
	
	G0 X{safe_home_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front"
	
	
	G0 X{(printable_x_max - margin_x)} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_right"
	
	
	G0 X{safe_home_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back"
	
	
	G0 X{margin_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_left"
	
	
	G0 X{margin_x} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="left"
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_BEACON_ECHO_BEACON_OFFSET
	
	
	_LED_BEACON_CALIBRATION_END
	
	{% endif %}

[gcode_macro _BEACON_STORE_BEACON_OFFSET]
gcode = 
	
	{% set location = params.LOCATION|lower %}
	
	
	{% set last_z = printer.beacon.last_offset_result["delta"]|default(0)|float %}
	
	
	{% if location == "center" %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE={location} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_BEACON_OFFSET]
gcode = 
	
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float * 1000 %}
	{% set front_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_left|default(0)|float * 1000 %}
	{% set front = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front|default(0)|float * 1000 %}
	{% set front_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_right|default(0)|float * 1000 %}
	{% set right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].right|default(0)|float * 1000 %}
	{% set back_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_right|default(0)|float * 1000 %}
	{% set back = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back|default(0)|float * 1000 %}
	{% set back_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_left|default(0)|float * 1000 %}
	{% set left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].left|default(0)|float * 1000 %}
	
	{% set line_1 = "Front left:    %.6fμm" % (front_left) %}
	{% set line_2 = "Front center:  %.6fμm" % (front) %}
	{% set line_3 = "Front right:   %.6fμm" % (front_right) %}
	{% set line_4 = "Left center:   %.6fμm" % (left) %}
	{% set line_5 = "Right center:  %.6fμm" % (right) %}
	{% set line_6 = "Back left:     %.6fμm" % (back_left) %}
	{% set line_7 = "Back center:   %.6fμm" % (back) %}
	{% set line_8 = "Back right:    %.6fμm" % (back_right) %}
	
	{% set max_value = [(front_left|abs), (front|abs), (front_right|abs), (left|abs), (right|abs), (back_left|abs), (back|abs), (back_right|abs)]|max %}
	{% if max_value <= 50 %}
	{% set type = "success" %}
	{% set recommendation = "Very low beacon offset: %.6fμm._N_No beacon scan compensation needed." % max_value %}
	{% elif max_value > 50 and max_value <= 100 %}
	{% set type = "info" %}
	{% set recommendation = "Low beacon offset: %.6fμm._N_You may experience first layer inconsistensies, consider beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 100 and max_value <= 150 %}
	{% set type = "warning" %}
	{% set recommendation = "High beacon offset: %.6fμm._N_High chance of first layer problems, beacon scan compensation is highly encouraged." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 150 and max_value <= 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Very High beacon offset: %.6fμm._N_You will encounter first layer problems on large prints unless you activate beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Extremely high beacon offset: %.6fμm._N_You have significant scan/contact inconsistency which is indicative of mechanical problems, please investigate before resorting to software compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon offset relative to the center" TYPE={type} MSG={'"_N_%s_N__N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s"' % (recommendation, line_1, line_2, line_3, line_4, line_5, line_6, line_7, line_8)}

[gcode_macro BEACON_CREATE_SCAN_COMPENSATION_MESH]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set profile = params.PROFILE|default("auto")|string %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set keep_temp_meshes = params.KEEP_TEMP_MESHES|default(0) %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' %}
	{% set desired_spacing = printer["gcode_macro RatOS"].beacon_scan_compensation_desired_spacing|float %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	
	{% if not beacon_scan_compensation_enable %}
	RATOS_ECHO MSG="Beacon scan compensation is disabled!"
	
	{% else %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	
	
	RATOS_ECHO MSG="Please wait..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	G1 Z2.5 F{z_speed}
	{% if beacon_adaptive_heat_soak %}
	
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,9000]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if not (beacon_adaptive_heat_soak or bed_heat_soak_time > 0) %}
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if printer.z_tilt is defined %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% endif %}
	{% if printer.quad_gantry_level is defined %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% endif %}
	
	
	_BEACON_CREATE_SCAN_COMPENSATION_MESH_CORE PROFILE="{profile}" DESIRED_SPACING={desired_spacing} CHAMBER_TEMP={chamber_temp} KEEP_TEMP_MESHES={keep_temp_meshes}
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	{% if automated %}
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon scan compensation mesh created!"
	
	
	{% if not automated %}
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED]
gcode = 
	
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED" MSG="beacon_scan_compensation_profile {beacon_scan_compensation_profile}, beacon_scan_compensation_enable {beacon_scan_compensation_enable}"
	
	{% if beacon_scan_compensation_enable %}
	BEACON_APPLY_SCAN_COMPENSATION PROFILE="{beacon_scan_compensation_profile}"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL]
gcode = 
	
	{% set beacon_contact_start_print_true_zero = params.BEACON_CONTACT_START_PRINT_TRUE_ZERO|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = params.beacon_contact_calibrate_model_on_true_zero|lower == 'true' %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and not printer.beacon.model %}
	{% set beacon_model_required_for_true_zero = beacon_contact_start_print_true_zero and not beacon_contact_calibrate_model_on_true_zero %}
	{% set beacon_model_required_for_homing =
	printer.fastconfig.settings.stepper_z.endstop_pin == 'probe:z_virtual_endstop'
	and (( printer.fastconfig.settings.beacon.home_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower != 'true')
	or ( printer.fastconfig.settings.beacon.default_probe_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower != 'true' )) %}
	{% if beacon_model_required_for_homing or beacon_model_required_for_true_zero %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("An active Beacon model is required. Have you performed initial Beacon calibration?") }
	{% endif %}
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION]
gcode = 
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set bed_temp_mismatch_is_error = true if printer["gcode_macro RatOS"].beacon_scan_compensation_bed_temp_mismatch_is_error|default(false)|lower == 'true' else false %}
	
	{% set bed_temp = params.BED_TEMP|default(0)|float %}
	{% if bed_temp == 0 %}
	{% set bed_temp = printer.heater_bed.temperature %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_PREFLIGHT_CHECK_BEACON" MSG="beacon_scan_compensation_profile={beacon_scan_compensation_profile}, beacon_scan_compensation_enable={beacon_scan_compensation_enable}, bed_temp={bed_temp}"
	
	{% if beacon_scan_compensation_enable %}
	_VALIDATE_COMPENSATION_MESH_PROFILE PROFILE="{beacon_scan_compensation_profile}" TITLE="Check Beacon scan compensation profile" SUBJECT="Configured compensation profile '{beacon_scan_compensation_profile}'" COMPARE_BED_TEMP={bed_temp} COMPARE_BED_TEMP_IS_ERROR={bed_temp_mismatch_is_error}
	{% endif %}

[gcode_macro _BEACON_MAYBE_SCAN_COMPENSATION]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set needs_scan_compensation = true if printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].needs_compensation|default(false)|lower == 'true' else false %}
	
	{% if needs_scan_compensation %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% endif %}

[gcode_macro _BEACON_HOME_AND_ABL]
gcode = 
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	{% if needs_rehoming %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}

[gcode_macro SAVE_Z_OFFSET]
description = Deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead, or in Mainsail use the SAVE button in the Z-OFFSET section.
gcode = 
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default('false')|lower == 'true' %}
	{% set msg = "SAVE_Z_OFFSET is deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead,_N_or in Mainsail use the SAVE button in the Z-OFFSET section."%}
	{% if not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% set msg = msg + "_N_You must then use the SAVE_CONFIG command to persist the change." %}
	{% endif %}
	CONSOLE_ECHO TYPE="error" MSG="{msg}"

[gcode_macro _BEACON_OFFSET_COMPARE]
gcode = 
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing..."
	
	
	BEACON_OFFSET_COMPARE SAMPLES_DROP=1 SAMPLES=3
	BEACON_QUERY

[fan]
pin = rpi:gpio4

[fan_generic part_fan_t0]
pin = PA8
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[fan_generic part_fan_t1]
pin = PE5
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[heater_fan toolhead_cooling_fan_t0]
heater = extruder
shutdown_speed = 1
pin = toolboard_t0:PB4

[heater_fan toolhead_cooling_fan_t1]
heater = extruder1
shutdown_speed = 1
pin = toolboard_t1:PB4

[controller_fan controller_fan]
pin = dinghy:PA4
tachometer_pin = dinghy:PC15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[z_offset_probe]
pin = ^PG10
z_offset = -7
y_offset = 0
x_offset = 37.5
speed = 10
samples = 3
sample_retract_dist = 5
lift_speed = 10.0
samples_result = median
samples_tolerance = 0.2
samples_tolerance_retries = 5

[neopixel vaoc_led]
pin = PB10
chain_count = 6
color_order = GRB

[heater_fan vaoc_fan]
pin = PD13
heater = heater_bed
fan_speed = 1.0
heater_temp = 50

[fan_generic filter]
pin = !PD14
enable_pin = PD15

[gcode_macro T0]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = True
variable_color = "7bff33"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = -32.6
variable_parking_position = -57.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=0 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[gcode_macro T1]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = False
variable_color = "0ea5e9"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = 532.6
variable_parking_position = 557.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=1 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[save_variables]
filename = /home/pi/printer_data/config/ratos-variables.cfg

[mcu dinghy]
serial = /dev/serial/by-id/usb-Klipper_stm32f072xb_Dragon_dinghy-if00

[temperature_sensor th0]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA0

[temperature_sensor th1]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA1

[temperature_sensor th2]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA2

[temperature_sensor th3]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA3

[controller_fan CTL2]
pin = dinghy:PB14
tachometer_pin = dinghy:PB15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[mcu plasma]
serial = /dev/serial/by-id/usb-Klipper_rp2040_Plasma-if00

[neopixel Chamber_Lights]
pin = plasma:gpio15
chain_count = 140
color_order = GRBW
initial_red = 0.0
initial_green = 0.0
initial_blue = 0.0
initial_white = 0.1

[beacon model default]
model_coef = 1.5287863993594841,
	1.9289099639750602,
	0.8838828622507556,
	0.25554883784260735,
	-0.015171504024913506,
	0.3044946127013882,
	0.15820427856566457,
	-0.25262403959326246,
	0.042488512846660914,
	0.16662470122520964
model_domain = 1.842634574664148e-07,1.9339206373083917e-07
model_range = 0.200000,5.000000
model_temp = 13.222247
model_offset = 0.00000

[bed_mesh default]
version = 1
points = 
	0.016163, 0.016713, 0.001923, -0.017658, -0.031574, -0.032498, -0.030898, -0.032177, -0.035213, -0.031148, -0.021322, -0.016924, -0.015012, -0.013911, -0.012197, -0.012583, -0.010489, -0.007529, -0.003986, -0.000980, 0.005518, 0.014442, 0.027426, 0.034677, 0.037410, 0.040391, 0.041842, 0.040369, 0.037615, 0.030776, 0.027664, 0.022856, 0.016892, 0.015398, 0.014717, 0.006921, 0.001532, 0.000731, 0.008657, 0.014036
	0.005356, -0.005066, -0.016998, -0.029668, -0.038334, -0.043672, -0.041139, -0.042488, -0.045199, -0.039432, -0.028746, -0.023642, -0.024058, -0.022802, -0.019679, -0.018514, -0.018102, -0.016476, -0.012722, -0.010077, -0.001809, 0.007180, 0.019853, 0.027754, 0.029964, 0.033626, 0.036783, 0.032018, 0.029372, 0.020847, 0.017634, 0.011926, 0.009013, 0.009254, 0.007972, -0.001380, -0.006940, -0.002160, 0.006135, 0.008330
	-0.004900, -0.006720, -0.021914, -0.039691, -0.050459, -0.050377, -0.046281, -0.048755, -0.054708, -0.051499, -0.033927, -0.027632, -0.030243, -0.031447, -0.024387, -0.021408, -0.020382, -0.018068, -0.015930, -0.013877, -0.006099, 0.003479, 0.013310, 0.024783, 0.025522, 0.030849, 0.033573, 0.031409, 0.025495, 0.016683, 0.011264, 0.008805, 0.006856, 0.008059, 0.007305, 0.002581, -0.003320, -0.003239, 0.004691, 0.010045
	-0.008791, -0.019334, -0.029149, -0.040533, -0.051698, -0.058235, -0.054863, -0.054840, -0.055692, -0.049534, -0.036731, -0.033053, -0.035667, -0.035315, -0.024352, -0.023825, -0.022538, -0.020438, -0.018207, -0.015389, -0.006515, 0.001966, 0.013591, 0.019434, 0.020600, 0.024967, 0.029425, 0.026812, 0.018980, 0.007878, 0.002360, 0.000859, 0.003849, 0.005649, 0.005421, -0.000416, -0.007906, -0.003164, 0.007582, 0.010039
	-0.018512, -0.018210, -0.033932, -0.050501, -0.061588, -0.064139, -0.060236, -0.062528, -0.067065, -0.062039, -0.045815, -0.039448, -0.040521, -0.042080, -0.033870, -0.030878, -0.027396, -0.024548, -0.021298, -0.020041, -0.011880, -0.002847, 0.008689, 0.015857, 0.015934, 0.018697, 0.022439, 0.022106, 0.017916, 0.005879, 0.001037, -0.001311, -0.001335, 0.001897, 0.003656, 0.000561, -0.006084, -0.005683, 0.000338, 0.006245
	-0.028558, -0.036721, -0.044680, -0.054969, -0.066140, -0.075045, -0.073515, -0.073161, -0.075696, -0.068963, -0.058892, -0.053111, -0.050990, -0.048040, -0.041262, -0.037419, -0.034866, -0.031845, -0.029787, -0.026524, -0.017896, -0.009322, -0.001010, 0.005819, 0.008058, 0.010456, 0.013266, 0.012529, 0.007992, -0.001491, -0.006769, -0.009303, -0.005980, -0.003567, -0.003340, -0.011496, -0.018818, -0.014808, -0.004181, -0.000733
	-0.037253, -0.038393, -0.053129, -0.066170, -0.075959, -0.079233, -0.077475, -0.082688, -0.086779, -0.083983, -0.069005, -0.062542, -0.060351, -0.058481, -0.051101, -0.043149, -0.039837, -0.037039, -0.034698, -0.031301, -0.024330, -0.019786, -0.010285, -0.001967, 0.002812, 0.004899, 0.009657, 0.006946, 0.002155, -0.005232, -0.009851, -0.011218, -0.011509, -0.010097, -0.010293, -0.013175, -0.018958, -0.019846, -0.012107, -0.005641
	-0.046584, -0.055590, -0.062606, -0.069218, -0.080399, -0.087414, -0.089037, -0.092376, -0.095115, -0.088957, -0.080802, -0.073290, -0.068741, -0.064591, -0.054452, -0.048270, -0.045916, -0.044559, -0.042047, -0.039605, -0.032667, -0.025789, -0.019495, -0.012773, -0.006697, -0.003025, 0.001413, 0.000817, -0.004738, -0.013008, -0.017605, -0.018191, -0.018524, -0.016356, -0.016750, -0.021992, -0.028943, -0.025791, -0.016146, -0.010447
	-0.051029, -0.051677, -0.068218, -0.079622, -0.088590, -0.089331, -0.089731, -0.096072, -0.105329, -0.100771, -0.087584, -0.079320, -0.075489, -0.072081, -0.064183, -0.054662, -0.048601, -0.049465, -0.047050, -0.045011, -0.040009, -0.032508, -0.025212, -0.018144, -0.011996, -0.008136, -0.003187, -0.003214, -0.006646, -0.013044, -0.019446, -0.020615, -0.022270, -0.021298, -0.020215, -0.020946, -0.026034, -0.026598, -0.021025, -0.012328
	-0.057184, -0.064908, -0.073093, -0.081584, -0.091971, -0.097048, -0.097688, -0.101869, -0.106651, -0.102162, -0.095658, -0.087938, -0.082718, -0.077017, -0.069608, -0.060682, -0.056889, -0.056864, -0.054260, -0.052011, -0.044563, -0.038927, -0.031943, -0.025832, -0.021170, -0.014319, -0.009046, -0.008543, -0.011751, -0.020287, -0.026608, -0.027259, -0.029120, -0.025549, -0.023221, -0.027725, -0.032477, -0.028427, -0.019343, -0.014932
	-0.060411, -0.062241, -0.080781, -0.090744, -0.100903, -0.099702, -0.098468, -0.104236, -0.116853, -0.112701, -0.102623, -0.095036, -0.091407, -0.089871, -0.079701, -0.070222, -0.064325, -0.063875, -0.062248, -0.059396, -0.052699, -0.047589, -0.041526, -0.028442, -0.024526, -0.019549, -0.015403, -0.014251, -0.017989, -0.022824, -0.027328, -0.029155, -0.033315, -0.032426, -0.027619, -0.030776, -0.033688, -0.032458, -0.027219, -0.019649
	-0.067541, -0.076514, -0.082321, -0.088656, -0.099968, -0.104930, -0.105875, -0.109051, -0.115531, -0.112996, -0.105760, -0.100390, -0.096171, -0.090011, -0.080050, -0.073632, -0.067451, -0.067031, -0.065225, -0.062471, -0.056370, -0.050129, -0.041626, -0.030801, -0.027579, -0.022472, -0.014826, -0.015306, -0.020316, -0.025953, -0.030661, -0.034103, -0.035502, -0.032738, -0.031311, -0.037314, -0.041306, -0.035280, -0.027449, -0.020395
	-0.068162, -0.069269, -0.088235, -0.096809, -0.103385, -0.103271, -0.102507, -0.109535, -0.123412, -0.118580, -0.106622, -0.099580, -0.097644, -0.096978, -0.087259, -0.077196, -0.068978, -0.067016, -0.063682, -0.062548, -0.057901, -0.052295, -0.044088, -0.032703, -0.026551, -0.021607, -0.014155, -0.013747, -0.017390, -0.022419, -0.027444, -0.030877, -0.033450, -0.032423, -0.032041, -0.033598, -0.035149, -0.034054, -0.029356, -0.020998
	-0.069473, -0.075924, -0.083569, -0.089648, -0.101235, -0.105828, -0.109144, -0.112613, -0.117233, -0.114186, -0.107090, -0.098616, -0.097084, -0.094257, -0.086773, -0.076409, -0.069532, -0.066472, -0.060956, -0.059191, -0.052886, -0.047752, -0.041275, -0.032437, -0.027780, -0.020398, -0.012061, -0.010133, -0.014056, -0.021528, -0.027924, -0.030605, -0.030609, -0.026068, -0.029346, -0.033991, -0.038254, -0.030610, -0.021109, -0.015885
	-0.068084, -0.066409, -0.083944, -0.094013, -0.102504, -0.105274, -0.106036, -0.112090, -0.121664, -0.117824, -0.104850, -0.097467, -0.098833, -0.098622, -0.089603, -0.078147, -0.068143, -0.066300, -0.061573, -0.057727, -0.054825, -0.048625, -0.040164, -0.030532, -0.025948, -0.020264, -0.014196, -0.010702, -0.013794, -0.019775, -0.026095, -0.028838, -0.030254, -0.027944, -0.027980, -0.030915, -0.032446, -0.028861, -0.023732, -0.014676
	-0.065280, -0.068669, -0.076948, -0.082397, -0.094986, -0.105117, -0.107099, -0.108954, -0.112557, -0.110326, -0.100725, -0.096325, -0.096240, -0.092388, -0.081185, -0.071682, -0.065650, -0.062250, -0.057027, -0.054691, -0.048349, -0.042069, -0.032712, -0.027728, -0.023396, -0.018458, -0.008357, -0.005699, -0.011447, -0.020033, -0.026387, -0.030280, -0.028443, -0.023735, -0.023838, -0.031580, -0.034204, -0.027768, -0.018029, -0.010628
	-0.061662, -0.057052, -0.075163, -0.086710, -0.094182, -0.097544, -0.098814, -0.105908, -0.114460, -0.111718, -0.097559, -0.091614, -0.093860, -0.093098, -0.081687, -0.069410, -0.064117, -0.062745, -0.055603, -0.051413, -0.048043, -0.040363, -0.031842, -0.023420, -0.017470, -0.012600, -0.008163, -0.003898, -0.007635, -0.013254, -0.019807, -0.025153, -0.027074, -0.023513, -0.023727, -0.028669, -0.029153, -0.024831, -0.018735, -0.009246
	-0.056176, -0.059439, -0.066501, -0.071527, -0.085216, -0.094918, -0.097595, -0.099419, -0.101847, -0.102015, -0.093849, -0.089867, -0.088840, -0.083167, -0.071832, -0.062522, -0.058023, -0.057771, -0.053050, -0.048285, -0.041374, -0.033527, -0.024473, -0.018428, -0.013958, -0.008161, -0.001196, 0.001754, -0.004016, -0.011132, -0.018325, -0.021813, -0.021514, -0.016948, -0.018061, -0.025702, -0.028671, -0.021470, -0.011028, -0.001934
	-0.059202, -0.050525, -0.065461, -0.076792, -0.084156, -0.088538, -0.090719, -0.096070, -0.105729, -0.105136, -0.090350, -0.083865, -0.087807, -0.086145, -0.074773, -0.064235, -0.057641, -0.055896, -0.051286, -0.046566, -0.042431, -0.034723, -0.023762, -0.014983, -0.009126, -0.004877, 0.000094, 0.003492, -0.000931, -0.005883, -0.011665, -0.015251, -0.016432, -0.016119, -0.015373, -0.018827, -0.019994, -0.017564, -0.012298, 0.002094
	-0.055561, -0.058184, -0.062669, -0.068111, -0.080741, -0.091895, -0.093911, -0.094387, -0.100239, -0.100695, -0.089841, -0.085682, -0.085212, -0.082910, -0.073072, -0.063594, -0.056157, -0.053482, -0.048107, -0.045405, -0.039982, -0.029777, -0.019905, -0.013872, -0.009732, -0.004272, 0.003500, 0.006909, 0.001302, -0.004626, -0.012374, -0.014751, -0.014637, -0.011794, -0.012913, -0.018244, -0.023377, -0.018086, -0.006575, 0.003294
	-0.062834, -0.047300, -0.060870, -0.073023, -0.079303, -0.082121, -0.083623, -0.091321, -0.100996, -0.098896, -0.085406, -0.078881, -0.081932, -0.082077, -0.074409, -0.063158, -0.053822, -0.050328, -0.045077, -0.039678, -0.035825, -0.028532, -0.017793, -0.009121, -0.003444, -0.000905, 0.003990, 0.007745, 0.004595, 0.000143, -0.004555, -0.007411, -0.010850, -0.010100, -0.010079, -0.013177, -0.016434, -0.014663, -0.010248, -0.000213
	-0.054748, -0.053907, -0.057576, -0.063118, -0.072478, -0.081366, -0.084424, -0.086348, -0.089718, -0.089305, -0.081771, -0.076889, -0.076923, -0.073518, -0.067973, -0.057643, -0.050848, -0.046966, -0.041560, -0.036436, -0.029233, -0.020685, -0.010240, -0.004935, -0.001084, 0.002478, 0.009168, 0.014038, 0.010885, 0.004752, -0.001650, -0.004209, -0.003998, -0.002336, -0.003784, -0.010930, -0.016480, -0.012798, -0.003650, 0.002998
	-0.059345, -0.041989, -0.057435, -0.068229, -0.072857, -0.072586, -0.075155, -0.083286, -0.091292, -0.089727, -0.073702, -0.068353, -0.072910, -0.073863, -0.065527, -0.053635, -0.046064, -0.043899, -0.037607, -0.031251, -0.026194, -0.018885, -0.008095, 0.000309, 0.004911, 0.007046, 0.010642, 0.015635, 0.015277, 0.012612, 0.008074, 0.004852, 0.001546, 0.000504, 0.000589, -0.002769, -0.006432, -0.007765, -0.005391, 0.006950
	-0.050324, -0.049088, -0.052417, -0.057257, -0.063818, -0.071057, -0.074636, -0.075459, -0.079445, -0.077368, -0.068788, -0.063940, -0.065040, -0.063419, -0.054864, -0.044910, -0.038774, -0.036951, -0.031149, -0.026080, -0.018383, -0.011985, -0.001732, 0.003893, 0.007180, 0.011120, 0.017429, 0.021738, 0.019167, 0.015812, 0.011027, 0.007243, 0.006720, 0.009346, 0.006598, -0.003776, -0.009199, -0.007592, 0.005481, 0.014396
	-0.058437, -0.035937, -0.050762, -0.060425, -0.061123, -0.059090, -0.062399, -0.072124, -0.080338, -0.074950, -0.060985, -0.054754, -0.059333, -0.060500, -0.051714, -0.038834, -0.031117, -0.031693, -0.025186, -0.017982, -0.014316, -0.010137, 0.000228, 0.008774, 0.014018, 0.016470, 0.019918, 0.022071, 0.021109, 0.019957, 0.018698, 0.015803, 0.013135, 0.011136, 0.008719, 0.003522, -0.000994, 0.000525, 0.006297, 0.018454
	-0.046143, -0.041577, -0.045391, -0.046668, -0.051722, -0.057607, -0.062802, -0.065205, -0.068243, -0.066293, -0.058216, -0.051324, -0.051806, -0.051018, -0.043393, -0.032431, -0.024016, -0.023321, -0.018504, -0.013897, -0.008455, -0.001123, 0.006609, 0.010462, 0.013887, 0.019328, 0.024804, 0.026590, 0.023420, 0.020337, 0.017129, 0.017199, 0.016391, 0.015616, 0.013257, 0.005832, -0.000019, 0.003462, 0.014308, 0.023624
	-0.051989, -0.030294, -0.043380, -0.051339, -0.050711, -0.048193, -0.052258, -0.061218, -0.070507, -0.068810, -0.049476, -0.042352, -0.046018, -0.046673, -0.038670, -0.027263, -0.018137, -0.018587, -0.013603, -0.008482, -0.004647, -0.000011, 0.008230, 0.015652, 0.019436, 0.023069, 0.024762, 0.027750, 0.028115, 0.026227, 0.022220, 0.023166, 0.020341, 0.018455, 0.014918, 0.011932, 0.007138, 0.008523, 0.014718, 0.026201
	-0.041448, -0.035286, -0.036538, -0.037577, -0.044652, -0.049300, -0.051092, -0.052841, -0.058068, -0.056947, -0.046235, -0.038436, -0.037494, -0.034175, -0.028932, -0.016904, -0.010075, -0.010552, -0.004464, -0.001243, 0.003236, 0.010200, 0.015604, 0.020362, 0.023157, 0.028023, 0.032826, 0.035958, 0.034819, 0.030600, 0.025988, 0.026013, 0.026284, 0.025661, 0.022322, 0.013336, 0.006464, 0.011312, 0.022330, 0.031668
	-0.048540, -0.022534, -0.035260, -0.042156, -0.042749, -0.037408, -0.038818, -0.047322, -0.056808, -0.053643, -0.035691, -0.027822, -0.028789, -0.028255, -0.020274, -0.007285, -0.000723, -0.000788, 0.005440, 0.008938, 0.008953, 0.012074, 0.017957, 0.025241, 0.029175, 0.032057, 0.033733, 0.038359, 0.039349, 0.037161, 0.034052, 0.034585, 0.032020, 0.029940, 0.026326, 0.024577, 0.020432, 0.021586, 0.024568, 0.034552
	-0.033086, -0.027982, -0.029443, -0.029011, -0.035629, -0.040579, -0.038290, -0.037389, -0.041260, -0.040430, -0.032279, -0.021394, -0.018817, -0.015525, -0.007558, 0.006345, 0.011048, 0.011271, 0.013497, 0.017030, 0.017449, 0.022752, 0.026764, 0.030722, 0.033532, 0.037203, 0.043356, 0.048536, 0.047776, 0.043851, 0.039311, 0.039944, 0.039954, 0.038931, 0.034893, 0.030946, 0.023127, 0.027359, 0.034859, 0.043920
	-0.036218, -0.016846, -0.030897, -0.036980, -0.037261, -0.033334, -0.030888, -0.034074, -0.042142, -0.039980, -0.021377, -0.013603, -0.014171, -0.013131, -0.001768, 0.014998, 0.020060, 0.018173, 0.019934, 0.024704, 0.023739, 0.024617, 0.027288, 0.035116, 0.041187, 0.043128, 0.045921, 0.051709, 0.053031, 0.050698, 0.047697, 0.047728, 0.046845, 0.043201, 0.041805, 0.040728, 0.036184, 0.034435, 0.035120, 0.045329
	-0.029808, -0.023871, -0.026541, -0.026705, -0.031203, -0.036908, -0.034411, -0.029231, -0.028090, -0.026102, -0.016691, -0.007747, -0.004471, 0.001560, 0.010738, 0.025062, 0.027672, 0.024833, 0.026976, 0.029502, 0.030754, 0.035709, 0.039403, 0.044719, 0.046379, 0.049250, 0.054178, 0.059793, 0.059542, 0.052111, 0.047608, 0.050103, 0.053142, 0.052747, 0.050045, 0.044102, 0.033149, 0.035392, 0.045678, 0.054080
	-0.032238, -0.008993, -0.023999, -0.030969, -0.028658, -0.024887, -0.024493, -0.028088, -0.031053, -0.022849, -0.003868, 0.004647, 0.004540, 0.007560, 0.018373, 0.031401, 0.035778, 0.033768, 0.035173, 0.035884, 0.036597, 0.038940, 0.044566, 0.053914, 0.056554, 0.056382, 0.056449, 0.060387, 0.062696, 0.058223, 0.055016, 0.056193, 0.056891, 0.052793, 0.052741, 0.052626, 0.048117, 0.045032, 0.048033, 0.055100
	-0.019758, -0.015110, -0.017814, -0.018871, -0.023340, -0.028653, -0.026880, -0.018681, -0.017020, -0.011343, -0.001002, 0.008249, 0.014012, 0.020367, 0.026878, 0.038534, 0.041827, 0.039532, 0.039775, 0.039109, 0.043172, 0.049325, 0.056604, 0.059583, 0.059329, 0.059876, 0.062766, 0.068759, 0.067214, 0.059657, 0.055950, 0.056798, 0.058619, 0.058591, 0.059849, 0.056473, 0.046841, 0.047921, 0.058342, 0.065346
	-0.018628, -0.000296, -0.014764, -0.022634, -0.020483, -0.016362, -0.015485, -0.017352, -0.020246, -0.010362, 0.008635, 0.018414, 0.018542, 0.024258, 0.033370, 0.045728, 0.049983, 0.044610, 0.044638, 0.047649, 0.049220, 0.051954, 0.058932, 0.065915, 0.069102, 0.067410, 0.067680, 0.073734, 0.072203, 0.067293, 0.063945, 0.064378, 0.065047, 0.061989, 0.062882, 0.063468, 0.059707, 0.057986, 0.059739, 0.066139
	-0.010091, -0.006551, -0.008018, -0.009589, -0.016068, -0.020662, -0.019451, -0.010985, -0.009391, -0.003580, 0.007826, 0.019598, 0.024961, 0.033762, 0.040618, 0.050868, 0.052139, 0.050495, 0.049198, 0.051777, 0.056840, 0.061771, 0.068414, 0.072295, 0.073443, 0.072145, 0.073414, 0.079338, 0.075988, 0.067367, 0.064745, 0.064435, 0.066982, 0.065811, 0.067424, 0.063230, 0.058438, 0.059982, 0.067672, 0.072460
	-0.016254, 0.006291, -0.008031, -0.013944, -0.014475, -0.010741, -0.009932, -0.011709, -0.015503, -0.006971, 0.013190, 0.024865, 0.029121, 0.033942, 0.044335, 0.054572, 0.058078, 0.055224, 0.055897, 0.058327, 0.061207, 0.063939, 0.070506, 0.078141, 0.084203, 0.081223, 0.079519, 0.082883, 0.080890, 0.076174, 0.071279, 0.073064, 0.071225, 0.066859, 0.069860, 0.070836, 0.069427, 0.069140, 0.070950, 0.075269
	-0.008127, 0.000730, 0.001164, -0.000308, -0.006659, -0.012343, -0.011463, -0.003755, -0.001876, 0.005166, 0.016616, 0.030243, 0.036509, 0.045020, 0.053681, 0.063738, 0.066425, 0.063964, 0.062796, 0.065633, 0.071912, 0.077280, 0.082580, 0.086477, 0.089798, 0.089603, 0.091453, 0.096125, 0.088708, 0.079903, 0.074317, 0.076190, 0.075399, 0.075242, 0.079628, 0.077855, 0.071473, 0.073702, 0.082757, 0.088086
	-0.010951, 0.013218, -0.000878, -0.006241, -0.005623, 0.000046, 0.000158, -0.002943, -0.005314, 0.005491, 0.026890, 0.035754, 0.041490, 0.045829, 0.059325, 0.070249, 0.074114, 0.071815, 0.073229, 0.076313, 0.080778, 0.081554, 0.087919, 0.096206, 0.101562, 0.101674, 0.100494, 0.103989, 0.100292, 0.093977, 0.088080, 0.088136, 0.086555, 0.081494, 0.084966, 0.087073, 0.084113, 0.085184, 0.087700, 0.092188
	-0.002972, 0.006020, 0.006098, 0.004303, 0.001326, -0.002386, -0.001840, 0.005325, 0.008624, 0.016246, 0.026781, 0.039696, 0.048540, 0.055938, 0.066982, 0.076497, 0.080828, 0.079669, 0.080127, 0.083754, 0.089783, 0.093456, 0.100570, 0.105322, 0.107132, 0.110571, 0.113141, 0.118064, 0.111721, 0.101634, 0.093555, 0.093112, 0.093104, 0.092325, 0.094780, 0.092552, 0.085283, 0.088882, 0.097508, 0.105280
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 11.4
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Preperations]
version = 1
points = 
	0.012158, -0.006098, -0.020628, -0.034069, -0.049418, -0.058491, -0.062706, -0.063181, -0.065552, -0.063461, -0.057373, -0.056717, -0.056579, -0.054080, -0.053373, -0.056878, -0.057281, -0.055224, -0.049676, -0.047605, -0.041454, -0.034605, -0.022490, -0.011292, -0.009411, -0.005344, -0.003510, -0.002717, -0.005999, -0.010712, -0.013141, -0.015611, -0.020004, -0.017667, -0.016629, -0.022248, -0.024864, -0.024065, -0.014921, -0.010826
	-0.005958, -0.021084, -0.033800, -0.047903, -0.059950, -0.071345, -0.072502, -0.073350, -0.075852, -0.072963, -0.067236, -0.064315, -0.065698, -0.064338, -0.062871, -0.065238, -0.067095, -0.063584, -0.059241, -0.057846, -0.051380, -0.043157, -0.030230, -0.019950, -0.018121, -0.014291, -0.009354, -0.013065, -0.016464, -0.022925, -0.025337, -0.026541, -0.030577, -0.029068, -0.027094, -0.030532, -0.034241, -0.032625, -0.021498, -0.020513
	-0.017526, -0.027763, -0.040710, -0.055305, -0.068172, -0.079641, -0.081247, -0.081903, -0.083679, -0.081855, -0.073270, -0.070340, -0.072083, -0.071536, -0.066055, -0.065901, -0.069085, -0.066531, -0.063284, -0.061616, -0.053366, -0.047292, -0.035451, -0.023167, -0.022205, -0.016699, -0.012552, -0.014153, -0.018802, -0.030443, -0.032210, -0.034051, -0.034437, -0.031439, -0.030406, -0.032817, -0.036351, -0.034849, -0.024250, -0.019489
	-0.017750, -0.030284, -0.043463, -0.055839, -0.071865, -0.084888, -0.086157, -0.084619, -0.086681, -0.084515, -0.075246, -0.073263, -0.075604, -0.075123, -0.069177, -0.070723, -0.071097, -0.068644, -0.065465, -0.063718, -0.057574, -0.049335, -0.036556, -0.028418, -0.028259, -0.023387, -0.018454, -0.020519, -0.027499, -0.038314, -0.041534, -0.041886, -0.039972, -0.036438, -0.033959, -0.033009, -0.038291, -0.036339, -0.022688, -0.024783
	-0.021354, -0.034103, -0.047541, -0.060551, -0.075691, -0.089373, -0.092241, -0.091621, -0.093203, -0.090723, -0.082480, -0.079781, -0.079706, -0.079674, -0.074365, -0.073780, -0.073465, -0.070165, -0.064970, -0.065503, -0.059104, -0.051038, -0.041817, -0.031243, -0.031386, -0.028837, -0.023658, -0.024237, -0.029641, -0.039210, -0.042766, -0.044461, -0.041863, -0.039075, -0.034881, -0.034571, -0.039386, -0.038253, -0.031659, -0.024202
	-0.027696, -0.041184, -0.054054, -0.064759, -0.080898, -0.094964, -0.097906, -0.098033, -0.101256, -0.098300, -0.091517, -0.088420, -0.086945, -0.085220, -0.079938, -0.079979, -0.079828, -0.074842, -0.072903, -0.072415, -0.065384, -0.057454, -0.048482, -0.040977, -0.039336, -0.036065, -0.032553, -0.034336, -0.039337, -0.046271, -0.049398, -0.051220, -0.049530, -0.045000, -0.045029, -0.042100, -0.049767, -0.046386, -0.035574, -0.032188
	-0.033426, -0.046259, -0.059363, -0.068024, -0.084858, -0.097009, -0.103434, -0.106215, -0.107319, -0.106178, -0.100333, -0.097536, -0.095352, -0.091322, -0.086332, -0.082309, -0.081440, -0.078413, -0.075067, -0.073134, -0.068255, -0.062667, -0.054300, -0.046004, -0.042001, -0.039181, -0.035010, -0.036092, -0.041599, -0.048788, -0.051751, -0.051179, -0.051019, -0.049121, -0.045860, -0.046756, -0.050005, -0.051613, -0.040237, -0.035349
	-0.037931, -0.051993, -0.066455, -0.075044, -0.088177, -0.102890, -0.108223, -0.112373, -0.115787, -0.113421, -0.108543, -0.105936, -0.101048, -0.096863, -0.090726, -0.087882, -0.086665, -0.083874, -0.081096, -0.080894, -0.075125, -0.071038, -0.063072, -0.054696, -0.051039, -0.046728, -0.042566, -0.043887, -0.048745, -0.056834, -0.059808, -0.060521, -0.060664, -0.057968, -0.056317, -0.052477, -0.058814, -0.055877, -0.046325, -0.042545
	-0.041429, -0.053634, -0.067633, -0.077111, -0.090998, -0.103561, -0.109445, -0.114741, -0.120075, -0.119821, -0.114703, -0.110411, -0.105589, -0.099826, -0.093730, -0.089705, -0.087199, -0.086439, -0.082688, -0.082221, -0.078348, -0.073203, -0.065273, -0.058731, -0.054025, -0.049231, -0.044830, -0.043830, -0.045839, -0.054137, -0.059075, -0.059515, -0.058546, -0.056956, -0.054145, -0.053129, -0.056587, -0.056341, -0.047057, -0.039936
	-0.044295, -0.058972, -0.072101, -0.082726, -0.095001, -0.106449, -0.111505, -0.118363, -0.124608, -0.123506, -0.120263, -0.115400, -0.110227, -0.104535, -0.100348, -0.095757, -0.092961, -0.092377, -0.089613, -0.088047, -0.084834, -0.079314, -0.072500, -0.064519, -0.060449, -0.055767, -0.051803, -0.050997, -0.052855, -0.058115, -0.063348, -0.065363, -0.067936, -0.063474, -0.061475, -0.054726, -0.062529, -0.055352, -0.048878, -0.044991
	-0.045804, -0.056574, -0.073308, -0.082450, -0.097495, -0.107467, -0.111501, -0.116418, -0.126724, -0.125980, -0.123231, -0.120494, -0.114667, -0.111289, -0.103451, -0.099228, -0.095880, -0.095882, -0.093328, -0.091000, -0.087051, -0.081909, -0.075949, -0.064971, -0.061050, -0.055137, -0.049046, -0.047319, -0.049806, -0.056968, -0.059608, -0.060249, -0.063032, -0.060556, -0.056284, -0.056263, -0.058891, -0.057890, -0.051554, -0.042382
	-0.049818, -0.062681, -0.076305, -0.084328, -0.098717, -0.107866, -0.113937, -0.120088, -0.128622, -0.128931, -0.126353, -0.123191, -0.118529, -0.115642, -0.106288, -0.103976, -0.099708, -0.097750, -0.094501, -0.094545, -0.090910, -0.085952, -0.077352, -0.067196, -0.062435, -0.057738, -0.052934, -0.051098, -0.055294, -0.061112, -0.063120, -0.067525, -0.067979, -0.066558, -0.064608, -0.060597, -0.067812, -0.057641, -0.056224, -0.046471
	-0.050591, -0.060432, -0.075602, -0.083877, -0.096933, -0.106147, -0.112334, -0.118295, -0.127966, -0.128757, -0.125157, -0.121831, -0.118557, -0.116124, -0.108723, -0.104502, -0.099469, -0.095841, -0.090662, -0.089822, -0.087969, -0.084545, -0.076375, -0.064821, -0.059093, -0.053427, -0.047372, -0.044341, -0.047964, -0.054064, -0.057133, -0.059152, -0.061568, -0.059109, -0.056640, -0.056691, -0.056844, -0.054564, -0.048514, -0.040641
	-0.047704, -0.059564, -0.073127, -0.080945, -0.093764, -0.105483, -0.111501, -0.118792, -0.124812, -0.126576, -0.122064, -0.118087, -0.116126, -0.114867, -0.108053, -0.103336, -0.097558, -0.093250, -0.086537, -0.085303, -0.083677, -0.079292, -0.070542, -0.062526, -0.056818, -0.052534, -0.044035, -0.041353, -0.046942, -0.051329, -0.055481, -0.062777, -0.058499, -0.058025, -0.057390, -0.053562, -0.060843, -0.046555, -0.046260, -0.036083
	-0.046496, -0.052983, -0.067518, -0.076904, -0.091704, -0.103105, -0.111995, -0.117751, -0.122307, -0.122941, -0.118230, -0.115004, -0.114258, -0.113138, -0.105515, -0.098417, -0.093384, -0.090070, -0.083281, -0.079846, -0.078725, -0.075452, -0.066225, -0.057269, -0.053103, -0.047808, -0.039772, -0.036834, -0.041270, -0.047376, -0.051111, -0.053848, -0.053029, -0.050301, -0.048919, -0.050775, -0.050121, -0.046842, -0.039633, -0.030497
	-0.040695, -0.051685, -0.064038, -0.070974, -0.086679, -0.101773, -0.109889, -0.114373, -0.117883, -0.118764, -0.113125, -0.110931, -0.111099, -0.109664, -0.098733, -0.093182, -0.090154, -0.086213, -0.077214, -0.077108, -0.075555, -0.069117, -0.060704, -0.054093, -0.049253, -0.044799, -0.037536, -0.035304, -0.040134, -0.045456, -0.051720, -0.056675, -0.053743, -0.052923, -0.049701, -0.050238, -0.056776, -0.041485, -0.041755, -0.027329
	-0.039842, -0.039428, -0.055732, -0.063890, -0.079179, -0.092823, -0.101698, -0.106156, -0.111709, -0.113152, -0.108033, -0.104872, -0.105645, -0.103501, -0.094487, -0.087264, -0.084273, -0.080950, -0.074116, -0.070973, -0.068409, -0.062825, -0.054757, -0.044150, -0.040620, -0.036602, -0.031538, -0.026478, -0.031123, -0.037600, -0.042341, -0.046700, -0.047380, -0.042880, -0.040967, -0.045367, -0.044192, -0.038553, -0.029948, -0.020790
	-0.030596, -0.038279, -0.051528, -0.058981, -0.073983, -0.089044, -0.099173, -0.101740, -0.104830, -0.107083, -0.102306, -0.101554, -0.101336, -0.097146, -0.089217, -0.083800, -0.080621, -0.078071, -0.071535, -0.068328, -0.065806, -0.056882, -0.048683, -0.039756, -0.036349, -0.031328, -0.025351, -0.024133, -0.029773, -0.033858, -0.040011, -0.044146, -0.043900, -0.044797, -0.038019, -0.042319, -0.047297, -0.031851, -0.034318, -0.013527
	-0.032121, -0.034722, -0.047839, -0.054710, -0.069175, -0.084213, -0.094533, -0.097233, -0.100863, -0.104775, -0.099781, -0.097416, -0.098804, -0.096059, -0.086694, -0.079692, -0.076749, -0.074609, -0.068106, -0.063906, -0.061136, -0.055447, -0.045559, -0.035389, -0.029696, -0.025708, -0.020034, -0.017335, -0.022665, -0.028532, -0.032369, -0.035760, -0.037212, -0.035201, -0.032872, -0.034132, -0.035907, -0.032127, -0.025026, -0.009282
	-0.026707, -0.034374, -0.045183, -0.052691, -0.067014, -0.084964, -0.092286, -0.094441, -0.099291, -0.103609, -0.098278, -0.094972, -0.097169, -0.095394, -0.086653, -0.080205, -0.076284, -0.070594, -0.064535, -0.062012, -0.060174, -0.051216, -0.040622, -0.033396, -0.029636, -0.024235, -0.017274, -0.018232, -0.021459, -0.024778, -0.031754, -0.034481, -0.033398, -0.037949, -0.030432, -0.033219, -0.038432, -0.021975, -0.030052, -0.009295
	-0.028559, -0.029280, -0.042071, -0.048655, -0.061603, -0.076257, -0.086817, -0.091815, -0.095682, -0.098682, -0.093729, -0.091168, -0.092213, -0.090073, -0.084070, -0.077048, -0.072045, -0.066267, -0.060309, -0.053639, -0.051696, -0.046852, -0.034069, -0.025602, -0.020640, -0.018021, -0.013180, -0.009049, -0.013846, -0.018012, -0.021061, -0.024515, -0.027068, -0.026804, -0.024283, -0.025595, -0.028234, -0.025272, -0.019246, -0.008595
	-0.025711, -0.029003, -0.038836, -0.048015, -0.058511, -0.074480, -0.083738, -0.087945, -0.091439, -0.094310, -0.090288, -0.087858, -0.088589, -0.086163, -0.081829, -0.075146, -0.071136, -0.064399, -0.057338, -0.052103, -0.049650, -0.043210, -0.032998, -0.023124, -0.020191, -0.016625, -0.012433, -0.010465, -0.009871, -0.015007, -0.021217, -0.021582, -0.023800, -0.027652, -0.021527, -0.027137, -0.030828, -0.020152, -0.026202, -0.008568
	-0.031287, -0.022523, -0.035800, -0.041583, -0.052691, -0.065901, -0.075941, -0.079246, -0.083936, -0.086778, -0.082235, -0.078893, -0.080642, -0.079419, -0.074324, -0.067418, -0.062113, -0.057744, -0.049923, -0.043390, -0.040055, -0.035512, -0.023838, -0.015485, -0.009895, -0.008346, -0.005387, 0.001467, -0.000104, -0.003777, -0.007926, -0.012023, -0.013970, -0.014207, -0.013994, -0.017009, -0.019233, -0.019282, -0.014210, -0.001146
	-0.020719, -0.024043, -0.035160, -0.041635, -0.051902, -0.063884, -0.072884, -0.076738, -0.081856, -0.083761, -0.077857, -0.074651, -0.077952, -0.076310, -0.069721, -0.063240, -0.056775, -0.055188, -0.046711, -0.042996, -0.039499, -0.032268, -0.023129, -0.015735, -0.012305, -0.009383, -0.005789, -0.001996, -0.001166, -0.005106, -0.009634, -0.009864, -0.011905, -0.015913, -0.010246, -0.016645, -0.022975, -0.011972, -0.018524, 0.001048
	-0.026050, -0.019774, -0.032555, -0.037813, -0.044657, -0.054435, -0.065271, -0.071019, -0.075585, -0.077479, -0.072635, -0.069526, -0.071046, -0.070770, -0.063085, -0.055960, -0.050956, -0.049593, -0.042773, -0.034996, -0.032645, -0.029030, -0.020343, -0.011008, -0.005751, -0.003252, 0.000746, 0.003215, 0.001749, -0.000068, -0.001413, -0.002608, -0.005837, -0.007103, -0.008431, -0.012027, -0.015656, -0.014417, -0.006321, 0.003748
	-0.021728, -0.019178, -0.031232, -0.036249, -0.042206, -0.053190, -0.064017, -0.068545, -0.074597, -0.074544, -0.069543, -0.065779, -0.067928, -0.067354, -0.060655, -0.052790, -0.047723, -0.046044, -0.038188, -0.034539, -0.032080, -0.027152, -0.018902, -0.012508, -0.009304, -0.003955, -0.000288, -0.001549, -0.000556, -0.003756, -0.008467, -0.003851, -0.005999, -0.012959, -0.007423, -0.015332, -0.017388, -0.005695, -0.010807, 0.007710
	-0.028204, -0.017096, -0.027984, -0.032129, -0.038374, -0.046561, -0.059356, -0.061847, -0.069228, -0.070551, -0.065474, -0.059719, -0.059893, -0.060271, -0.053666, -0.047202, -0.041189, -0.039979, -0.033189, -0.028761, -0.025714, -0.021660, -0.014905, -0.007841, -0.004669, -0.001174, 0.001874, 0.005613, 0.005527, 0.001504, -0.000694, 0.001892, 0.001885, -0.002506, -0.005619, -0.007166, -0.009935, -0.007406, 0.000545, 0.009983
	-0.019393, -0.017785, -0.025482, -0.028146, -0.036861, -0.047528, -0.055696, -0.059118, -0.064151, -0.066346, -0.060565, -0.055661, -0.055495, -0.051944, -0.048147, -0.040645, -0.036359, -0.035990, -0.026764, -0.024843, -0.023572, -0.019648, -0.013807, -0.006811, -0.004589, -0.000266, 0.003010, 0.004931, 0.006834, 0.003254, -0.001690, 0.003120, 0.001036, -0.005283, 0.000659, -0.007399, -0.010996, -0.000832, -0.006381, 0.012135
	-0.021519, -0.010062, -0.018662, -0.023011, -0.029067, -0.036961, -0.043194, -0.048197, -0.053632, -0.055489, -0.050054, -0.045247, -0.042655, -0.040243, -0.034315, -0.027094, -0.022697, -0.021644, -0.015333, -0.010768, -0.013712, -0.012051, -0.005326, 0.000560, 0.005300, 0.007429, 0.009930, 0.015968, 0.016454, 0.012383, 0.010385, 0.011612, 0.011413, 0.008357, 0.006831, 0.005524, 0.003087, 0.003507, 0.009876, 0.018892
	-0.017331, -0.015238, -0.021971, -0.024651, -0.029507, -0.040209, -0.044232, -0.046101, -0.052689, -0.053151, -0.047133, -0.042985, -0.040475, -0.037020, -0.029999, -0.021348, -0.018232, -0.017876, -0.013058, -0.008535, -0.013279, -0.011527, -0.006296, -0.001615, 0.002270, 0.006991, 0.010272, 0.013407, 0.015950, 0.012503, 0.008026, 0.013701, 0.011513, 0.004867, 0.010667, 0.006774, 0.003571, 0.012416, 0.004875, 0.020961
	-0.022637, -0.011107, -0.018340, -0.023896, -0.028320, -0.038092, -0.041212, -0.041642, -0.044537, -0.046015, -0.041699, -0.035805, -0.033527, -0.030911, -0.022925, -0.010175, -0.007279, -0.008644, -0.005065, -0.000597, -0.003797, -0.004052, 0.000635, 0.006175, 0.010857, 0.012993, 0.016956, 0.022765, 0.023298, 0.020262, 0.018285, 0.019467, 0.021161, 0.018785, 0.017891, 0.017817, 0.013874, 0.012825, 0.015904, 0.025844
	-0.014532, -0.010189, -0.019385, -0.022584, -0.028159, -0.037803, -0.040566, -0.038125, -0.040339, -0.038899, -0.033171, -0.028143, -0.025641, -0.019755, -0.012463, -0.003824, -0.000871, -0.002698, -0.000197, 0.001952, -0.001353, -0.000188, 0.004902, 0.012600, 0.014373, 0.016449, 0.018872, 0.022822, 0.026385, 0.020681, 0.015275, 0.021387, 0.023535, 0.016733, 0.022161, 0.018819, 0.011276, 0.020785, 0.014683, 0.032409
	-0.016972, -0.004835, -0.015539, -0.019706, -0.022971, -0.032222, -0.037732, -0.035551, -0.033892, -0.031679, -0.024624, -0.019946, -0.016412, -0.010040, -0.003445, 0.005991, 0.008364, 0.006410, 0.008289, 0.009260, 0.007409, 0.008691, 0.015230, 0.022729, 0.025465, 0.025502, 0.026102, 0.030309, 0.031861, 0.026963, 0.024651, 0.027000, 0.029039, 0.025577, 0.027217, 0.027660, 0.023245, 0.021705, 0.026383, 0.034120
	-0.007042, -0.003943, -0.013314, -0.016082, -0.020497, -0.030911, -0.035096, -0.030889, -0.029351, -0.025337, -0.018980, -0.012449, -0.008879, -0.001902, 0.003577, 0.011256, 0.012460, 0.010502, 0.011904, 0.011483, 0.010067, 0.013356, 0.020792, 0.027368, 0.026382, 0.028554, 0.028164, 0.029993, 0.033232, 0.028830, 0.022354, 0.027991, 0.029607, 0.020011, 0.031066, 0.031755, 0.025061, 0.037228, 0.024607, 0.041453
	-0.012463, -0.000987, -0.008994, -0.014815, -0.017487, -0.026372, -0.031392, -0.028459, -0.025402, -0.024153, -0.015566, -0.007862, -0.004579, 0.001484, 0.010757, 0.017401, 0.019536, 0.016264, 0.016278, 0.018231, 0.018193, 0.018217, 0.025442, 0.034794, 0.036179, 0.034770, 0.033985, 0.040104, 0.040404, 0.034161, 0.030977, 0.032380, 0.034144, 0.031909, 0.033231, 0.035957, 0.034171, 0.033050, 0.038776, 0.042972
	-0.002758, 0.000700, -0.008467, -0.011525, -0.018705, -0.027522, -0.031609, -0.027494, -0.026315, -0.023221, -0.014164, -0.006562, -0.002205, 0.006453, 0.013689, 0.018647, 0.017673, 0.016751, 0.017380, 0.018782, 0.019038, 0.021992, 0.027475, 0.034748, 0.036870, 0.036635, 0.035394, 0.037519, 0.038008, 0.032063, 0.025834, 0.030409, 0.033142, 0.023991, 0.034882, 0.034323, 0.030317, 0.042711, 0.030793, 0.045129
	-0.011501, 0.004979, -0.003199, -0.009532, -0.013737, -0.022490, -0.028056, -0.025047, -0.023987, -0.021727, -0.011113, -0.003633, 0.003070, 0.010580, 0.020230, 0.025058, 0.026653, 0.024592, 0.024567, 0.025613, 0.027386, 0.029282, 0.037705, 0.042901, 0.046601, 0.045443, 0.044217, 0.048155, 0.045715, 0.039788, 0.034981, 0.038594, 0.038594, 0.034532, 0.038671, 0.042065, 0.040659, 0.042101, 0.045919, 0.050030
	-0.005239, 0.006624, -0.001837, -0.005350, -0.012024, -0.022230, -0.026144, -0.022704, -0.021559, -0.017450, -0.008515, 0.000433, 0.007392, 0.014546, 0.023538, 0.029043, 0.029892, 0.027280, 0.028785, 0.030662, 0.032758, 0.032649, 0.040035, 0.046372, 0.048654, 0.050330, 0.049538, 0.049746, 0.048851, 0.041068, 0.034598, 0.041375, 0.041379, 0.030621, 0.043091, 0.044712, 0.038634, 0.053475, 0.042814, 0.059369
	-0.011843, 0.005417, 0.000007, -0.005709, -0.011391, -0.019100, -0.024151, -0.021274, -0.019356, -0.016953, -0.004422, 0.002891, 0.010688, 0.018353, 0.027665, 0.035281, 0.036655, 0.034937, 0.036795, 0.039994, 0.042705, 0.042668, 0.048600, 0.055673, 0.059602, 0.061002, 0.059934, 0.064283, 0.061835, 0.052838, 0.048644, 0.048401, 0.048158, 0.044262, 0.049173, 0.053313, 0.050054, 0.051718, 0.058112, 0.062677
	-0.003249, 0.007140, -0.000190, -0.005182, -0.010664, -0.017472, -0.021072, -0.018928, -0.015929, -0.011810, -0.001170, 0.006999, 0.014346, 0.022026, 0.033087, 0.037703, 0.039304, 0.038986, 0.040531, 0.042739, 0.044912, 0.045850, 0.052980, 0.060894, 0.062495, 0.065477, 0.066306, 0.069035, 0.066301, 0.058359, 0.048879, 0.054660, 0.053906, 0.042834, 0.051292, 0.054304, 0.049390, 0.064968, 0.053062, 0.067337
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 80.0
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Peperations]
version = 1
points = 
	0.022498, 0.020830, 0.014175, -0.000111, -0.007965, -0.011932, -0.009252, -0.003320, -0.000118, 0.004151, 0.015991, 0.024593, 0.030148, 0.034696, 0.042241, 0.043592, 0.045307, 0.051419, 0.057700, 0.066468, 0.072764, 0.085492, 0.100446, 0.113063, 0.118900, 0.122870, 0.130290, 0.129755, 0.129462, 0.124089, 0.122420, 0.123461, 0.116841, 0.117893, 0.119241, 0.115227, 0.110631, 0.109920, 0.117187, 0.124332
	0.004953, 0.000716, -0.005511, -0.010742, -0.018400, -0.024021, -0.019665, -0.013525, -0.009878, -0.004126, 0.008939, 0.016408, 0.019292, 0.023840, 0.033007, 0.033600, 0.034448, 0.041047, 0.049029, 0.052882, 0.062512, 0.072410, 0.089182, 0.103027, 0.106205, 0.110789, 0.117912, 0.115269, 0.112784, 0.106051, 0.103603, 0.104209, 0.099603, 0.105100, 0.101466, 0.099610, 0.095780, 0.096420, 0.108661, 0.108286
	-0.007933, -0.002801, -0.011350, -0.022484, -0.029473, -0.033231, -0.030354, -0.021826, -0.018408, -0.013209, 0.001640, 0.008984, 0.012027, 0.014149, 0.024334, 0.028649, 0.030597, 0.034667, 0.041223, 0.046241, 0.051968, 0.062511, 0.079099, 0.090699, 0.097837, 0.101667, 0.108218, 0.106595, 0.104490, 0.095444, 0.089512, 0.089259, 0.089179, 0.091741, 0.094161, 0.094254, 0.091002, 0.088753, 0.095405, 0.102343
	-0.010759, -0.012564, -0.018170, -0.023960, -0.033106, -0.040910, -0.038354, -0.031441, -0.026122, -0.019953, -0.006267, 0.000733, 0.002678, 0.006102, 0.015437, 0.019860, 0.022689, 0.029563, 0.035629, 0.037302, 0.045089, 0.055137, 0.070820, 0.082978, 0.087158, 0.088614, 0.094487, 0.093851, 0.091038, 0.080923, 0.074433, 0.073797, 0.073058, 0.081788, 0.080734, 0.083111, 0.078149, 0.079373, 0.091335, 0.087853
	-0.027313, -0.019238, -0.027920, -0.036645, -0.043223, -0.049872, -0.048503, -0.043853, -0.040737, -0.035179, -0.021622, -0.013493, -0.010171, -0.007317, 0.001347, 0.007440, 0.011360, 0.015985, 0.023916, 0.026329, 0.031680, 0.042865, 0.056754, 0.067621, 0.072919, 0.075964, 0.080156, 0.081233, 0.077771, 0.068443, 0.063939, 0.062251, 0.063828, 0.065094, 0.069498, 0.071735, 0.067423, 0.064065, 0.069162, 0.076272
	-0.033298, -0.035618, -0.039940, -0.043358, -0.050731, -0.061413, -0.060545, -0.055944, -0.052261, -0.045471, -0.035624, -0.027633, -0.021472, -0.017300, -0.006949, -0.002776, -0.000154, 0.006413, 0.012882, 0.014721, 0.023411, 0.031711, 0.040565, 0.054702, 0.058761, 0.061734, 0.065369, 0.066037, 0.061059, 0.053849, 0.049600, 0.048373, 0.049189, 0.054631, 0.050470, 0.056349, 0.047074, 0.049651, 0.057444, 0.057485
	-0.046284, -0.039039, -0.049010, -0.054961, -0.061001, -0.068408, -0.069602, -0.066474, -0.063117, -0.059357, -0.049570, -0.041166, -0.035441, -0.029269, -0.019658, -0.012395, -0.008906, -0.005538, 0.002012, 0.008339, 0.013216, 0.018793, 0.031185, 0.040165, 0.047175, 0.050605, 0.054283, 0.054442, 0.049166, 0.043483, 0.039000, 0.040758, 0.040857, 0.040759, 0.042263, 0.043438, 0.040051, 0.035886, 0.041332, 0.048851
	-0.049893, -0.051919, -0.058103, -0.060142, -0.067656, -0.077159, -0.079195, -0.078019, -0.075421, -0.069471, -0.060409, -0.054194, -0.044226, -0.037275, -0.027912, -0.020020, -0.016789, -0.012491, -0.003457, 0.001129, 0.004540, 0.009435, 0.018232, 0.027941, 0.035138, 0.038227, 0.042656, 0.044103, 0.038517, 0.032121, 0.029666, 0.027319, 0.029774, 0.031572, 0.028887, 0.034828, 0.023795, 0.030023, 0.033606, 0.036047
	-0.061015, -0.055279, -0.067497, -0.072234, -0.078637, -0.083600, -0.085954, -0.087271, -0.088647, -0.083447, -0.073398, -0.065920, -0.058009, -0.048810, -0.040714, -0.032533, -0.027328, -0.020402, -0.011382, -0.006547, -0.005452, -0.002712, 0.004649, 0.014201, 0.021442, 0.025510, 0.032890, 0.034711, 0.030965, 0.026329, 0.018828, 0.019246, 0.018861, 0.019611, 0.020596, 0.021396, 0.020172, 0.015723, 0.020537, 0.029677
	-0.063777, -0.066149, -0.073750, -0.076131, -0.084016, -0.091900, -0.093741, -0.094496, -0.094840, -0.089548, -0.084332, -0.077263, -0.068485, -0.061963, -0.051082, -0.043658, -0.037912, -0.032323, -0.024324, -0.019914, -0.018261, -0.013727, -0.003485, 0.004316, 0.011418, 0.017023, 0.022980, 0.024505, 0.018896, 0.014000, 0.009498, 0.006074, 0.009480, 0.007611, 0.008958, 0.010086, -0.000341, 0.010423, 0.010467, 0.016794
	-0.072341, -0.064233, -0.079217, -0.084483, -0.091050, -0.094481, -0.095378, -0.096667, -0.100564, -0.098313, -0.093254, -0.086700, -0.079209, -0.071795, -0.061313, -0.051911, -0.046317, -0.042643, -0.037228, -0.031598, -0.027431, -0.020480, -0.012883, -0.003114, 0.004746, 0.010189, 0.015911, 0.017106, 0.014037, 0.008693, 0.005120, 0.003652, -0.000532, -0.001097, 0.001984, 0.000397, -0.002089, -0.002821, 0.000529, 0.009043
	-0.068927, -0.075835, -0.083530, -0.085213, -0.091299, -0.100015, -0.101020, -0.100921, -0.103349, -0.102493, -0.098069, -0.091292, -0.083452, -0.079672, -0.069612, -0.062472, -0.055862, -0.052233, -0.046746, -0.041991, -0.035219, -0.028225, -0.018698, -0.007309, -0.002458, 0.002051, 0.006595, 0.008468, 0.005218, -0.000205, -0.003131, -0.003647, -0.006151, -0.009154, -0.005539, -0.006971, -0.015297, -0.002874, -0.005242, 0.003706
	-0.070116, -0.067835, -0.086390, -0.089881, -0.095167, -0.099194, -0.100751, -0.103794, -0.106996, -0.105835, -0.098564, -0.092154, -0.085579, -0.083053, -0.074722, -0.066442, -0.059302, -0.053429, -0.047800, -0.042952, -0.039132, -0.034614, -0.025732, -0.012689, -0.005906, 0.001101, 0.006644, 0.010980, 0.007742, 0.002526, -0.000261, -0.004094, -0.008771, -0.008465, -0.007095, -0.008952, -0.010405, -0.010446, -0.006121, 0.002024
	-0.064366, -0.071780, -0.082938, -0.085702, -0.093522, -0.099237, -0.104020, -0.105939, -0.106226, -0.104298, -0.097541, -0.091253, -0.084969, -0.082450, -0.075561, -0.066547, -0.056511, -0.051248, -0.041287, -0.037794, -0.035633, -0.028059, -0.019518, -0.010556, -0.003388, 0.002054, 0.009492, 0.011478, 0.008555, 0.004735, -0.000781, -0.006427, -0.005697, -0.010270, -0.006112, -0.011704, -0.018717, -0.002750, -0.010971, 0.000116
	-0.076795, -0.064801, -0.080209, -0.085175, -0.093457, -0.101077, -0.104981, -0.106367, -0.106821, -0.105708, -0.098545, -0.090759, -0.086929, -0.083491, -0.074306, -0.064805, -0.055933, -0.049959, -0.042853, -0.036270, -0.034463, -0.029587, -0.018780, -0.010103, -0.003533, 0.001632, 0.007909, 0.014370, 0.009281, 0.004666, -0.002974, -0.007301, -0.010185, -0.008299, -0.006340, -0.009678, -0.011333, -0.010684, -0.006289, 0.002763
	-0.067470, -0.065770, -0.074038, -0.076420, -0.085702, -0.098704, -0.101940, -0.102629, -0.101903, -0.100342, -0.093820, -0.086941, -0.083804, -0.081020, -0.067700, -0.059395, -0.054055, -0.047911, -0.039687, -0.035672, -0.032029, -0.025979, -0.017057, -0.006973, -0.001656, 0.002001, 0.007249, 0.012112, 0.006541, 0.000572, -0.006284, -0.010415, -0.012279, -0.015087, -0.007848, -0.016491, -0.019704, -0.005357, -0.013151, 0.002966
	-0.074820, -0.054794, -0.069710, -0.075127, -0.082743, -0.091434, -0.095621, -0.097541, -0.099098, -0.097422, -0.089851, -0.083594, -0.081112, -0.078942, -0.066391, -0.057457, -0.050942, -0.048077, -0.041211, -0.034391, -0.030091, -0.026047, -0.014207, -0.005090, 0.000912, 0.005316, 0.010043, 0.015509, 0.011199, 0.004513, -0.001027, -0.006694, -0.011239, -0.011162, -0.009134, -0.013596, -0.014031, -0.011306, -0.007627, 0.001767
	-0.061695, -0.056074, -0.065188, -0.067950, -0.076218, -0.088303, -0.093436, -0.092999, -0.090937, -0.090555, -0.084407, -0.080354, -0.078692, -0.074308, -0.062767, -0.052729, -0.047475, -0.043949, -0.036669, -0.031720, -0.027940, -0.020058, -0.010125, -0.000940, 0.003512, 0.007720, 0.011869, 0.015296, 0.011180, 0.003886, -0.003309, -0.003380, -0.007926, -0.011633, -0.003540, -0.014182, -0.013975, -0.003720, -0.011797, 0.006338
	-0.070864, -0.046187, -0.061128, -0.065717, -0.072715, -0.083470, -0.088292, -0.087558, -0.087628, -0.089378, -0.083768, -0.077237, -0.077063, -0.071978, -0.061635, -0.052022, -0.046913, -0.041194, -0.034314, -0.028661, -0.027048, -0.021438, -0.009769, -0.001205, 0.004637, 0.008928, 0.013264, 0.017277, 0.013442, 0.007295, 0.003623, -0.002524, -0.004256, -0.005789, -0.004213, -0.007305, -0.010487, -0.010885, -0.006086, 0.007386
	-0.059345, -0.049207, -0.056858, -0.060052, -0.066579, -0.080604, -0.086910, -0.085647, -0.085267, -0.087618, -0.081260, -0.075368, -0.073937, -0.069758, -0.058235, -0.051634, -0.045288, -0.038732, -0.032262, -0.027928, -0.024928, -0.019266, -0.007996, 0.000923, 0.005834, 0.008336, 0.013557, 0.017068, 0.012350, 0.006475, 0.000982, 0.001103, -0.006223, -0.006853, -0.000966, -0.013148, -0.013975, -0.006310, -0.011605, 0.006165
	-0.066591, -0.039715, -0.053663, -0.059514, -0.065911, -0.075018, -0.080214, -0.082968, -0.083447, -0.085380, -0.079055, -0.071985, -0.070247, -0.065856, -0.057767, -0.049975, -0.044481, -0.039103, -0.031217, -0.024927, -0.020997, -0.016440, -0.004831, 0.004061, 0.009463, 0.011160, 0.014777, 0.020638, 0.017816, 0.011360, 0.006171, 0.002164, -0.002119, -0.003117, -0.003031, -0.005156, -0.011400, -0.011762, -0.009295, -0.000001
	-0.060314, -0.046160, -0.052794, -0.054967, -0.062049, -0.074106, -0.080446, -0.081200, -0.080809, -0.080477, -0.076170, -0.070932, -0.069101, -0.063634, -0.055720, -0.049501, -0.044939, -0.040131, -0.032438, -0.022882, -0.017627, -0.012524, -0.001324, 0.006685, 0.011868, 0.013658, 0.016095, 0.021837, 0.020158, 0.012528, 0.006089, 0.005453, -0.000976, -0.002140, 0.001104, -0.010111, -0.010612, -0.007452, -0.014357, 0.001011
	-0.075633, -0.036609, -0.049346, -0.055490, -0.059336, -0.067616, -0.073859, -0.075613, -0.076372, -0.078009, -0.070627, -0.064206, -0.064430, -0.061999, -0.054551, -0.047386, -0.040817, -0.037398, -0.028062, -0.018505, -0.012195, -0.007531, 0.001481, 0.011790, 0.019955, 0.022349, 0.022131, 0.024492, 0.023359, 0.019186, 0.014655, 0.008357, 0.004176, 0.002971, 0.002955, -0.000237, -0.005884, -0.010152, -0.009506, 0.002811
	-0.059008, -0.039658, -0.046978, -0.048324, -0.052285, -0.063338, -0.069082, -0.070556, -0.070625, -0.070049, -0.064460, -0.057403, -0.056723, -0.052882, -0.046968, -0.041507, -0.033211, -0.029974, -0.022900, -0.013579, -0.008803, -0.004962, 0.005653, 0.017026, 0.028171, 0.028651, 0.024731, 0.026850, 0.023371, 0.017073, 0.015171, 0.016616, 0.005521, 0.005756, 0.007586, -0.005103, -0.006856, -0.005604, -0.006599, 0.007528
	-0.068330, -0.030233, -0.043154, -0.047439, -0.047149, -0.051149, -0.060971, -0.063014, -0.065775, -0.064636, -0.058200, -0.050987, -0.050925, -0.050115, -0.041299, -0.033907, -0.026306, -0.024199, -0.017123, -0.009196, -0.006314, -0.003809, 0.004760, 0.015324, 0.026665, 0.029649, 0.028724, 0.027131, 0.025150, 0.021808, 0.019981, 0.016766, 0.012347, 0.008776, 0.005760, -0.000224, -0.004294, -0.005879, -0.002457, 0.010054
	-0.053519, -0.031388, -0.038255, -0.037590, -0.039245, -0.046335, -0.056314, -0.057830, -0.060291, -0.058967, -0.051413, -0.045449, -0.043947, -0.042018, -0.034113, -0.025887, -0.019539, -0.017727, -0.012711, -0.005860, -0.003102, 0.000774, 0.009438, 0.015884, 0.022961, 0.024229, 0.026012, 0.029407, 0.026717, 0.020406, 0.017796, 0.020289, 0.012243, 0.009711, 0.009234, -0.005990, -0.001013, 0.000740, -0.002144, 0.013012
	-0.068972, -0.023416, -0.032912, -0.036134, -0.035915, -0.040435, -0.047452, -0.051460, -0.055021, -0.055776, -0.048697, -0.039554, -0.036785, -0.035561, -0.029056, -0.021075, -0.013416, -0.012134, -0.007237, -0.000622, 0.001662, 0.005393, 0.012038, 0.019764, 0.023514, 0.026252, 0.028191, 0.031400, 0.031365, 0.027993, 0.023275, 0.021009, 0.018930, 0.014093, 0.009022, 0.004773, 0.002094, 0.001348, 0.005643, 0.015078
	-0.050527, -0.022437, -0.028090, -0.026206, -0.028387, -0.036911, -0.041310, -0.044227, -0.046970, -0.046769, -0.038081, -0.031386, -0.029516, -0.024050, -0.019435, -0.012381, -0.005732, -0.004173, 0.000911, 0.006849, 0.007360, 0.010699, 0.017436, 0.023369, 0.028527, 0.029640, 0.031002, 0.034727, 0.036582, 0.030763, 0.026015, 0.028623, 0.020834, 0.016185, 0.016933, 0.002829, 0.004984, 0.009818, 0.008874, 0.020032
	-0.067395, -0.010220, -0.021024, -0.024567, -0.024087, -0.029620, -0.032317, -0.034341, -0.038392, -0.038789, -0.030285, -0.021590, -0.017175, -0.014435, -0.007732, -0.000529, 0.005605, 0.007078, 0.012454, 0.017758, 0.016774, 0.015574, 0.020748, 0.028369, 0.033644, 0.034771, 0.036537, 0.040293, 0.042118, 0.039979, 0.035655, 0.033354, 0.030928, 0.024890, 0.021491, 0.018938, 0.013668, 0.012501, 0.017108, 0.023515
	-0.038833, -0.012802, -0.018564, -0.017459, -0.019062, -0.027068, -0.030119, -0.028336, -0.029665, -0.030695, -0.022239, -0.013522, -0.008358, -0.004785, 0.000463, 0.010662, 0.015564, 0.016950, 0.020281, 0.025300, 0.022680, 0.022717, 0.026679, 0.031617, 0.035801, 0.037098, 0.041294, 0.045640, 0.047879, 0.042000, 0.038044, 0.040629, 0.033892, 0.031247, 0.031584, 0.018500, 0.020116, 0.019823, 0.016638, 0.029979
	-0.054356, -0.002258, -0.012712, -0.017288, -0.016713, -0.022907, -0.024293, -0.021563, -0.022620, -0.021953, -0.015330, -0.005386, -0.000764, 0.002640, 0.009997, 0.022869, 0.028174, 0.027730, 0.030977, 0.035707, 0.032818, 0.030889, 0.033638, 0.038561, 0.044265, 0.045141, 0.047683, 0.051815, 0.054004, 0.050991, 0.045574, 0.043899, 0.044055, 0.039092, 0.035909, 0.032091, 0.026891, 0.022169, 0.024865, 0.030848
	-0.031827, -0.000102, -0.006368, -0.006487, -0.006247, -0.014001, -0.017110, -0.013043, -0.010851, -0.008764, -0.000213, 0.006477, 0.011144, 0.018309, 0.024745, 0.033643, 0.038648, 0.039249, 0.041148, 0.045266, 0.041693, 0.040999, 0.045484, 0.052613, 0.057066, 0.054753, 0.055112, 0.059287, 0.060203, 0.052465, 0.047993, 0.050999, 0.047464, 0.046460, 0.044507, 0.031433, 0.032267, 0.032025, 0.029852, 0.040329
	-0.053848, 0.008122, -0.005187, -0.009032, -0.006543, -0.010012, -0.013005, -0.011663, -0.008957, -0.004668, 0.005458, 0.012800, 0.016893, 0.023554, 0.031737, 0.038741, 0.043870, 0.043337, 0.046621, 0.047581, 0.045654, 0.044827, 0.050363, 0.058747, 0.061023, 0.060485, 0.059059, 0.061821, 0.061391, 0.055971, 0.051067, 0.050038, 0.051018, 0.046533, 0.043334, 0.042562, 0.036118, 0.029798, 0.032773, 0.039524
	-0.025830, 0.006164, -0.000655, 0.000164, 0.000088, -0.008033, -0.011008, -0.006017, -0.001301, 0.004088, 0.011848, 0.020276, 0.024465, 0.033383, 0.039126, 0.044268, 0.047916, 0.047402, 0.050050, 0.050456, 0.048891, 0.051771, 0.058154, 0.063246, 0.065463, 0.063072, 0.060950, 0.065351, 0.064614, 0.057455, 0.051194, 0.055723, 0.050906, 0.046407, 0.048283, 0.036561, 0.037400, 0.036887, 0.031589, 0.046759
	-0.041184, 0.017683, 0.006408, 0.000358, 0.001923, -0.002498, -0.003907, -0.001746, 0.001864, 0.006784, 0.017297, 0.026916, 0.030940, 0.036439, 0.045987, 0.050809, 0.054636, 0.052055, 0.053180, 0.056698, 0.057069, 0.055779, 0.063193, 0.067815, 0.071856, 0.070651, 0.067674, 0.070718, 0.070797, 0.062598, 0.057842, 0.056835, 0.056713, 0.051260, 0.048727, 0.048227, 0.044844, 0.039559, 0.041218, 0.044920
	-0.014008, 0.018619, 0.011274, 0.010878, 0.008771, 0.001246, -0.001819, 0.003600, 0.008052, 0.011983, 0.021970, 0.030757, 0.037662, 0.045972, 0.053195, 0.057661, 0.059206, 0.058383, 0.060240, 0.061039, 0.062504, 0.064497, 0.070278, 0.077704, 0.080246, 0.077015, 0.072985, 0.075685, 0.072584, 0.063534, 0.057732, 0.061938, 0.057545, 0.050931, 0.054863, 0.045820, 0.048882, 0.049675, 0.043484, 0.051538
	-0.045038, 0.028947, 0.019821, 0.012917, 0.013648, 0.007951, 0.005122, 0.007823, 0.012411, 0.015320, 0.025036, 0.036734, 0.045314, 0.052208, 0.062220, 0.065610, 0.068489, 0.066665, 0.068454, 0.069025, 0.071080, 0.073373, 0.079623, 0.085651, 0.088907, 0.088954, 0.084254, 0.084464, 0.080300, 0.072471, 0.067316, 0.066430, 0.065143, 0.057630, 0.058650, 0.059627, 0.057197, 0.054105, 0.055295, 0.057879
	-0.017117, 0.027364, 0.023067, 0.022758, 0.019246, 0.011825, 0.007962, 0.011522, 0.017237, 0.021779, 0.031329, 0.042642, 0.052349, 0.060322, 0.069568, 0.074657, 0.075211, 0.072882, 0.075373, 0.078391, 0.079512, 0.081816, 0.086101, 0.091730, 0.095061, 0.095682, 0.092100, 0.092873, 0.085769, 0.077219, 0.068392, 0.073179, 0.069972, 0.061240, 0.068306, 0.062227, 0.061008, 0.064520, 0.058543, 0.070728
	-0.042759, 0.035472, 0.029514, 0.023812, 0.024176, 0.020576, 0.017397, 0.018716, 0.022981, 0.027634, 0.041262, 0.050991, 0.058558, 0.067060, 0.077829, 0.083609, 0.084719, 0.082815, 0.085352, 0.087363, 0.091238, 0.091692, 0.096562, 0.102513, 0.106436, 0.108184, 0.105828, 0.107257, 0.102415, 0.090768, 0.084257, 0.081410, 0.081286, 0.073523, 0.074433, 0.076576, 0.070376, 0.068350, 0.071896, 0.072962
	-0.003143, 0.035517, 0.033266, 0.032727, 0.031843, 0.025862, 0.023177, 0.026936, 0.032953, 0.037457, 0.049289, 0.057429, 0.066625, 0.072540, 0.083814, 0.089321, 0.092420, 0.093053, 0.094752, 0.096876, 0.098364, 0.101271, 0.105185, 0.113505, 0.115784, 0.118957, 0.117138, 0.117934, 0.110930, 0.101497, 0.091051, 0.092731, 0.090574, 0.079282, 0.084691, 0.078426, 0.073451, 0.081698, 0.072811, 0.084352
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 19.8
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity
=======================
Unhandled exception during connect
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 130, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 123, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 112, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/resonance_generator.py", line 161, in load_config
    return ResonanceGenerator(config)
  File "/home/pi/klipper/klippy/extras/resonance_generator.py", line 85, in __init__
    self.generator = resonance_tester.SweepingVibrationsTestGenerator(tester_config)
AttributeError: module 'extras.resonance_tester' has no attribute 'SweepingVibrationsTestGenerator'
webhooks client 4124328744: New connection
webhooks client 4124328744: Client info {'program': 'Moonraker', 'version': 'v0.9.3-0-g71f9e67'}
Starting Klippy...
Args: ['/home/pi/klipper/klippy/klippy.py', '/home/pi/printer_data/config/printer.cfg', '-l', '/home/pi/printer_data/logs/klippy.log', '-I', '/home/pi/printer_data/comms/klippy.serial', '-a', '/home/pi/printer_data/comms/klippy.sock']
Git version: 'v0.12.0-402-g2817b348e-dirty'
Untracked files: klippy/extras/beacon.py, klippy/extras/beacon_adaptive_heat_soak.py, klippy/extras/beacon_mesh.py, klippy/extras/beacon_true_zero_correction.py, klippy/extras/beacon_user_z_offset.py, klippy/extras/fastconfig.py, klippy/extras/gcode_shell_command.py, klippy/extras/linear_movement_vibrations.py, klippy/extras/named_offsets.py, klippy/extras/ratos.py, (+4 files)
Branch: master
Remote: origin
Tracked URL: https://github.com/Klipper3d/klipper.git
CPU: 4 core ?
Python: '3.9.2 (default, Jan 24 2026, 09:41:14) \n[GCC 10.2.1 20210110]'
Start printer at Tue Mar 17 03:53:08 2026 (1773719588.3 9192.7)
===== Config file =====
[mcu rpi]
serial = /tmp/klipper_host_mcu

[board_pins btt-octopus-pro-h723-11]
aliases = 
	
	
	
	x_step_pin=PF13,
	x_dir_pin=PF12,
	x_enable_pin=PF14,
	x_uart_pin=PC4,
	x_diag_pin=PG6,
	x_endstop_pin=PG6,
	
	
	
	dual_carriage_step_pin=PF9,
	dual_carriage_dir_pin=PF10,
	dual_carriage_enable_pin=PG2,
	dual_carriage_uart_pin=PF2,
	dual_carriage_diag_pin=PG12,
	dual_carriage_endstop_pin=PG12,
	
	
	
	y_step_pin=PG0,
	y_dir_pin=PG1,
	y_enable_pin=PF15,
	y_uart_pin=PD11,
	y_diag_pin=PG9,
	y_endstop_pin=PG9,
	
	
	
	y1_step_pin=PG4,
	y1_dir_pin=PC1,
	y1_enable_pin=PA2,
	y1_uart_pin=PC7,
	y1_diag_pin=PG11,
	y1_endstop_pin=PG11,
	
	
	
	z0_step_pin=PC13,
	z0_dir_pin=PF0,
	z0_enable_pin=PF1,
	z0_uart_pin=PE4,
	z0_diag_pin=PG13,
	
	
	
	z1_step_pin=PE2,
	z1_dir_pin=PE3,
	z1_enable_pin=PD4,
	z1_uart_pin=PE1,
	z1_diag_pin=PG14,
	
	
	
	z2_step_pin=PE6,
	z2_dir_pin=PA14,
	z2_enable_pin=PE0,
	z2_uart_pin=PD3,
	z2_diag_pin=PG15,
	
	e_step_pin=PF11,
	e_dir_pin=PG3,
	e_enable_pin=PG5,
	e_uart_pin=PC6,
	
	e_heater_pin=PA2,
	e_sensor_pin=PF4,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=PA7,
	stepper_spi_miso_pin=PA6,
	stepper_spi_sclk_pin=PA5,
	adxl345_cs_pin=PA15,
	bltouch_sensor_pin=PB7,
	bltouch_control_pin=PB6,
	probe_pin=PB7,
	fan_part_cooling_pin=PA8,
	fan_toolhead_cooling_pin=PE5,
	fan_controller_board_pin=PD12,
	heater_bed_heating_pin=PA1,
	heater_bed_sensor_pin=PF3,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PG15,
	filament_sensor_motion_pin=PG14,
	ratrig_vaoc_probe_pin=PG10,
	ratrig_vaoc_led_pin=PB0,
	ratrig_vaoc_fan_pin=PD13,
	chamber_lighting_pin=PB11,
	chamber_filter_4p_fan_pin=PD14,
	chamber_filter_4p_fan_enable_pin=PD15

[mcu]
serial = /dev/RatOS/btt-octopus-pro-h723-11

[temperature_sensor Octopus_Pro_H723_V1.1]
sensor_type = temperature_mcu

[adxl345 controlboard]
cs_pin = PA15
spi_software_mosi_pin = PB5
spi_software_miso_pin = PB4
spi_software_sclk_pin = PB3

[board_pins toolboard_t0]
mcu = toolboard_t0
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t0]
serial = /dev/RatOS/btt-ebb42-gen2-10-t0

[temperature_sensor EBB42_Gen2_v1.0_T0]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t0

[lis2dw toolboard_t0]
axes_map = x, z, y
cs_pin = toolboard_t0:PB1
spi_software_mosi_pin = toolboard_t0:PB11
spi_software_miso_pin = toolboard_t0:PB2
spi_software_sclk_pin = toolboard_t0:PB10

[board_pins toolboard_t1]
mcu = toolboard_t1
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t1]
serial = /dev/RatOS/btt-ebb42-gen2-10-t1

[temperature_sensor EBB42_Gen2_v1.0_T1]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t1

[lis2dw toolboard_t1]
axes_map = x, z, y
cs_pin = toolboard_t1:PB1
spi_software_mosi_pin = toolboard_t1:PB11
spi_software_miso_pin = toolboard_t1:PB2
spi_software_sclk_pin = toolboard_t1:PB10

[gcode_macro RatOS]
variable_homing = "endstops"
variable_z_probe = "static"
variable_sensorless_x_current = 0.6
variable_sensorless_y_current = 0.9
variable_safe_home_x = "middle"
variable_safe_home_y = "middle"
variable_driver_type_x = "tmc2209"
variable_driver_type_y = "tmc2209"
variable_stowable_probe_stop_on_error = False
variable_chamber_filter_enable = True
variable_chamber_filter_speed = 0.5
variable_chamber_filter_disable_speed = 1.0
variable_chamber_filter_enable_at = "after_print_start"
variable_chamber_filter_disable_period = 300
variable_chamber_filter_disable_bed_temp = 0
variable_chamber_heater_enable = True
variable_chamber_heater_bed_temp = 115
variable_chamber_heater_preheating_temp = 150
variable_chamber_heater_heating_temp_offset = 25
variable_chamber_heater_control_external_heater = False
variable_chamber_heater_air_circulation_enable = True
variable_chamber_heater_air_circulation_fan_speed = 0.35
variable_chamber_heater_air_circulation_y_pos = 0
variable_chamber_heater_air_circulation_z_pos = 100
variable_chamber_heater_extra_fan_speed = 1.0
variable_chamber_heater_filter_fan_speed = 1.0
variable_bed_heat_soak_time = 0
variable_hotend_heat_soak_time = 0
variable_led_status_action = 0.0,1.0,1.0
variable_led_status_success = 0.0,1.0,0.0
variable_led_status_error = 1.0,0.0,1.0
variable_led_status_on = 1.0,1.0,1.0
variable_led_status_off = 0.0,0.0,1.0
variable_led_status_standby = 0.1,0.1,0.1
variable_led_status_heating = 1.0,0.0,0.0
variable_led_status_cooling = 0.0,0.0,1.0
variable_calibrate_bed_mesh = True
variable_adaptive_mesh = True
variable_start_print_park_in = "center"
variable_start_print_park_z_height = 3
variable_end_print_park_in = "back"
variable_pause_print_park_in = "back"
variable_end_print_park_z_hop = 20
variable_nozzle_priming = "primeblob"
variable_nozzle_prime_start_x = "max"
variable_nozzle_prime_start_y = "min"
variable_nozzle_prime_direction = "auto"
variable_nozzle_prime_bridge_fan = 102
variable_probe_for_priming_result = None
variable_probe_for_priming_end_result = None
variable_probe_for_priming_result_t1 = None
variable_probe_for_priming_end_result_t1 = None
variable_probe_for_priming_disable_mesh_constraints = False
variable_adaptive_prime_offset_threshold = -1.0
variable_last_z_offset = None
variable_runout_park_in = "front"
variable_enable_unload_tip_forming = False
variable_filament_unload_length = 150
description = RatOS variable storage macro, will echo variables to the console when run.
variable_relative_extrusion = True
variable_force_absolute_position = False
variable_preheat_extruder = True
variable_preheat_extruder_temp = 150
variable_macro_travel_speed = 600
variable_macro_travel_accel = 8000
variable_macro_z_speed = 15
variable_bed_margin_x = [59.6, 59.6]
variable_bed_margin_y = [14.35, 33.65]
variable_printable_x_min = 0
variable_printable_x_max = 0
variable_printable_y_min = 0
variable_printable_y_max = 0
variable_end_print_motors_off = True
variable_status_color_ok = "00FF00"
variable_status_color_error = "FF0000"
variable_status_color_unknown = "FFFF00"
variable_end_print_retract_filament = 10
gcode = 
	ECHO_RATOS_VARS
variable_auto_center_subject = False
variable_toolchange_zhop = 2.0
variable_toolchange_zspeed = 25
variable_toolchange_sync_fans = False
variable_toolchange_combined_zhop = False
variable_toolchange_travel_speed = 600
variable_toolchange_travel_accel = 8000
variable_toolchange_extrusion = 2.0
variable_toolchange_retraction = 2.0
variable_toolchange_feedrate = 7200
variable_toolchange_prepurging_timer = 0
variable_toolchange_standby_temp = -1
variable_toolchange_purge = 25
variable_toolchange_first_purge = 50
variable_beacon_bed_mesh_scv = 25
variable_beacon_contact_z_homing = False
variable_beacon_contact_start_print_true_zero = True
variable_beacon_contact_start_print_true_zero_fuzzy_position = True
variable_beacon_contact_calibrate_model_on_true_zero = True
variable_beacon_contact_wipe_before_true_zero = True
variable_beacon_contact_wipe_before_true_zero_method = "probe_clean"
variable_beacon_contact_true_zero_temp = 170
variable_beacon_contact_prime_probing = True
variable_beacon_contact_expansion_compensation = True
variable_beacon_contact_bed_mesh = False
variable_beacon_contact_bed_mesh_samples = 2
variable_beacon_contact_z_tilt_adjust = False
variable_beacon_contact_z_tilt_adjust_samples = 2
variable_beacon_scan_compensation_enable = True
variable_beacon_scan_compensation_profile = "auto"
variable_beacon_scan_compensation_desired_spacing = 10
variable_beacon_scan_compensation_bed_temp_mismatch_is_error = False
variable_beacon_contact_poke_bottom_limit = -1
variable_beacon_scan_method_automatic = False
variable_beacon_adaptive_heat_soak = True
variable_beacon_adaptive_heat_soak_max_wait = 5400
variable_beacon_adaptive_heat_soak_extra_wait_after_completion = 0
variable_beacon_adaptive_heat_soak_layer_quality = 3
variable_beacon_adaptive_heat_soak_maximum_first_layer_duration = 1800
variable_beacon_contact_start_print_true_zero_fuzzy_radius = 20
variable_homing_x = "endstop"
variable_homing_y = "endstop"
variable_default_toolhead = 0
variable_adxl_chip = ["lis2dw toolboard_t0", "lis2dw toolboard_t1"]
variable_shaper_x_freq = [54.2, 53.2, 53.6, 54.4]
variable_shaper_y_freq = [40.8, 47.6, 38.6, 38]
variable_shaper_x_type = ["mzv", "mzv", "mzv", "mzv"]
variable_shaper_y_type = ["mzv", "mzv", "mzv", "mzv"]
variable_x_driver_types = ["tmc5160"]
variable_x_axes = ["x"]
variable_y_driver_types = ["tmc5160", "tmc5160"]
variable_y_axes = ["y", "y1"]
variable_z_driver_types = ["tmc2209", "tmc2209", "tmc2209"]
variable_z_axes = ["z", "z1", "z2"]
variable_home_y_first = True

[ratos_homing]
axes = xyz
z_hop = 15
z_hop_speed = 15
gcode = 
	
	_LED_ON
	
	
	{% set prev_stop_on_error = printer["gcode_macro RatOS"].stowable_probe_stop_on_error %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set target_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	_IDEX_SINGLE
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE=True
	
	
	M400
	
	G90
	
	
	{% set X = true if params.X is defined else false %}
	{% set Y = true if params.Y is defined else false %}
	{% set Z = true if params.Z is defined else false %}
	{% if printer["gcode_macro RatOS"].home_y_first|default(false)|lower == 'true' %}
	HOME_Y X={X} Y={Y} Z={Z}
	HOME_X X={X} Y={Y} Z={Z}
	{% else %}
	HOME_X X={X} Y={Y} Z={Z}
	HOME_Y X={X} Y={Y} Z={Z}
	{% endif %}
	HOME_Z X={X} Y={Y} Z={Z}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE={prev_stop_on_error}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[gcode_macro HOME_X]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_x = printer["gcode_macro RatOS"].homing_x|lower %}
	{% set homing_x = homing_x if homing_x else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_X" MSG="printable_x_max: {printable_x_max}, safe_home_x: {safe_home_x}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}"
	
	
	{% if X or not Y and not Z %}
	{% if homing_x == 'endstop' %}
	G28 X
	{% elif homing_x == 'sensorless' %}
	{% if printer["dual_carriage"] is defined %}
	{ action_emergency_stop("sensorless homing not supported on IDEX!") }
	{% endif %}
	HOME_X_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_x to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_x, homing)) }
	{% endif %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1} MODE=PRIMARY
	G1 X{parking_position} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	{% endif %}
	{% set x_homed = True %}
	G0 X{safe_home_x} F{speed}
	M400
	{% endif %}

[gcode_macro HOME_Y]
gcode = 
	
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_y = printer["gcode_macro RatOS"].homing_y|lower %}
	{% set homing_y = homing_y if homing_y else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Y" MSG="printable_y_max: {printable_y_max}, safe_home_y: {safe_home_y}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}"
	
	
	{% if Y or not X and not Z %}
	{% if homing_y == 'endstop' %}
	G28 Y
	{% elif homing_y == 'sensorless' %}
	HOME_Y_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_y to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_y, homing)) }
	{% endif %}
	{% set y_homed = True %}
	G0 Y{safe_home_y} F{speed}
	{% endif %}

[gcode_macro HOME_Z]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	
	
	{% set beacon_contact_z_homing = true if printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_z_home_position_fuzzing_radius = printer["gcode_macro RatOS"].beacon_z_home_position_fuzzing_radius|default(0)|float %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Z" MSG="x_homed: {x_homed}, y_homed: {y_homed}, z_probe: {z_probe}, beacon_contact_z_homing: {beacon_contact_z_homing}"
	
	
	{% if Z or not Y and not X %}
	RATOS_ECHO MSG="Homing Z"
	{% if x_homed == False or y_homed == False %}
	{ action_emergency_stop("X and Y must be homed before homing Z") }
	{% else %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_homing %}
	{% if beacon_contact_start_print_true_zero %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% else %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	{% else %}
	G28 Z
	{% endif %}
	_Z_HOP
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro HOME_X_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	
	G4 P300
	
	G28 X
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"

[gcode_macro HOME_Y_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	
	G4 P300
	
	G28 Y
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"

[gcode_macro _Z_HOP]
description = Move Z axis up by Z_HOP distance at Z_HOP_SPEED. In relative mode it will move Z axis up by Z_HOP distance. In absolute mode it will move Z axis to Z_HOP distance.
gcode = 
	{% set z_hop = printer.fastconfig.config.ratos_homing.z_hop|float %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	G0 Z{z_hop} F{z_hop_speed}

[gcode_macro __MOVE_TO_SAFE_Z_HOME_ECHO_DEBUG]
gcode = 
	DEBUG_ECHO PREFIX="_MOVE_TO_SAFE_Z_HOME" MSG="x: {params.X}, y: {params.Y}, z_hop: {params.Z_HOP}, fuzzy_radius: {params.FUZZY_RADIUS}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}, printable_x_max: {printer['gcode_macro RatOS'].printable_x_max}, printable_y_max: {printer['gcode_macro RatOS'].printable_y_max}"

[gcode_macro MAYBE_HOME]
description = Only home unhomed axis. Specify ABL=1 to also ensure that automatic bed levelling is applied (if configured).
variable_is_kinematic_position_overriden = False
gcode = 
	{% set abl = params.ABL|default('')|lower in ('true', 'yes', '1') %}
	{% if printer["gcode_macro MAYBE_HOME"].is_kinematic_position_overriden|lower == 'true' %}
	RATOS_ECHO MSG="SET_CENTER_KINEMATIC_POSITION has been abused. Homing all axes. Please refrain from using SET_CENTER_KINEMATIC_POSITION outside of debugging purposes."
	G28
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=False
	{% else %}
	{% set axes = '' %}
	{% set isHomed = true %}
	{% set axesToHome = '' %}
	{% if params.X is defined %}
	{% set axes = axes ~ 'X ' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% endif %}
	{% if params.Y is defined %}
	{% set axes = axes ~ 'Y ' %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% endif %}
	{% if params.Z is defined %}
	{% set axes = axes ~ 'Z ' %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if params.X is not defined and params.Y is not defined and params.Z is not defined %}
	{% set axes = '' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if isHomed is false %}
	RATOS_ECHO MSG="Homing {axesToHome}"
	G28 {axesToHome}
	{% else %}
	RATOS_ECHO MSG="All requested axes already homed. Skipping homing."
	{% endif %}
	{% endif %}
	{% if abl %}
	{% if printer.z_tilt is defined %}
	{% if not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Performing Z tilt adjustment..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Z tilt already applied. Skipping Z tilt adjustment."
	{% endif %}
	{% elif printer.quad_gantry_level is defined %}
	{% if not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Performing quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Quad gantry leveling already applied. Skipping quad gantry leveling."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="No automatic bed leveling method configured. Skipping bed leveling."
	{% endif %}
	{% endif %}

[gcode_macro PID_CALIBRATE_HOTEND]
description = Perform a PID calibration test for a given extruder heater.
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set temp = params.TEMP|default(220)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_HOTEND" MSG="TEMP={temp}"
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO MSG="PID calibration hotend heater T0 at {temp}°C..."
	PID_CALIBRATE HEATER=extruder TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	
	{% if toolhead==0 or toolhead==1 %}
	RATOS_ECHO MSG="PID calibration hotend heater T{toolhead} at {temp}°C..."
	PID_CALIBRATE HEATER=extruder{'' if toolhead==0 else toolhead} TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_BED]
description = Perform a PID calibration test for the bed heater.
gcode = 
	
	{% set temp = params.TEMP|default(80)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_BED" MSG="TEMP={temp}"
	RATOS_ECHO MSG="PID calibration bed heater at {temp}°C..."
	
	
	PID_CALIBRATE HEATER=heater_bed TARGET={temp}
	
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_CHAMBER_HEATER]
description = Perform a PID calibration test for the chamber heater.
gcode = 
	
	{% set temp = params.TEMP|default(150)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_CHAMBER_HEATER" MSG="TEMP={temp}"
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	RATOS_ECHO MSG="PID calibration chamber heater at {temp}°C..."
	PID_CALIBRATE HEATER=chamber_heater TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_heater" %}
	{% set link_text = "RatOS Chamber Heater" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber heater found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro INITIALIZE_PA_TUNING]
description = Start a pressure advance tuning tower.
gcode = 
	
	{% set start = params.START|default(0.0)|float %}
	{% set factor = params.FACTOR|default(0.001)|float %}
	
	
	{% set layer_number = printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|default(0)|int %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if is_printing_gcode and layer_number < 2 %}
	DEBUG_ECHO PREFIX="START_PA_TOWER" MSG="START: {start}, FACTOR: {factor}"
	RATOS_ECHO MSG="Starting pressure advance tuning tower..."
	TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START={start} FACTOR={factor}
	{% else %}
	RATOS_ECHO MSG="Pressure advance tuning tower requires you to be printing gcode and on layer 1 to start."
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro CHAMBER_FILTER_ON]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	_CHAMBER_FILTER_TURN_ON
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro CHAMBER_FILTER_OFF]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Deactivating chamber filter..."
	_CHAMBER_FILTER_TURN_OFF
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set chamber_filter_enable_at = printer["gcode_macro RatOS"].chamber_filter_enable_at|default('after_print_start')|lower %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_ON" MSG="at: {at}, chamber_filter_enable: {chamber_filter_enable}, chamber_filter_enable_at: {chamber_filter_enable_at}, chamber_filter_speed: {chamber_filter_speed}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	{% if chamber_filter_enable_at == at %}
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	
	
	_CHAMBER_FILTER_TURN_ON AT={at}
	
	
	{% if chamber_filter_enable_at == "print_end" %}
	_LED_CHAMBER_FILTER_ON
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_OFF]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF" MSG="chamber_filter_enable: {chamber_filter_enable}, filter_disable_period: {filter_disable_period}, filter_disable_bed_temp: {filter_disable_bed_temp}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	
	{% if filter_disable_period > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting {filter_disable_period} seconds before turning chamber filter off..."
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION={filter_disable_period}
	{% endif %}
	
	
	{% if filter_disable_bed_temp > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting for bed temp to cool down to {filter_disable_bed_temp}°C to turn filter off..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM=0 MAXIMUM={filter_disable_bed_temp}
	_CHAMBER_FILTER_TURN_OFF
	_LED_CHAMBER_FILTER_OFF
	{% endif %}
	
	{% endif %}

[delayed_gcode _CHAMBER_FILTER_OFF_TIMER]
gcode = 
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF_TIMER" MSG="executed"
	
	
	_CHAMBER_FILTER_TURN_OFF
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Chamber filter turned off!"
	
	
	_LED_CHAMBER_FILTER_OFF

[gcode_macro _CHAMBER_FILTER_TURN_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_speed|default(0)|float %}
	{% if at == "print_end" %}
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_disable_speed|default(0)|float %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION=0
	
	
	SET_FAN_SPEED FAN=filter SPEED={chamber_filter_speed}

[gcode_macro _CHAMBER_FILTER_TURN_OFF]
gcode = 
	
	SET_FAN_SPEED FAN=filter SPEED=0

[gcode_macro _CHAMBER_FILTER_SANITY_CHECK]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	{% if filter_disable_bed_temp > 0 and filter_disable_period > 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable, not both.")}
	{% endif %}
	
	{% if filter_disable_bed_temp == 0 and filter_disable_period == 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable.")}
	{% endif %}
	
	{% endif %}

[gcode_macro CHAMBER_HEATER_ON]
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(45)|int %}
	
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp} IS_FROM_START_PRINT=False

[gcode_macro CHAMBER_HEATER_OFF]
gcode = 
	_CHAMBER_HEATER_OFF

[gcode_macro _CHAMBER_HEATER_ON]
variable_chamber_temp = 0
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	{% set is_from_start_print = true if params.IS_FROM_START_PRINT|default(True)|lower == 'true' else false %}
	
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set chamber_heater_enable = true if printer["gcode_macro RatOS"].chamber_heater_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}
	{% set chamber_heater_preheating_temp = printer["gcode_macro RatOS"].chamber_heater_preheating_temp|default(150)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	{% set chamber_heater_control_external_heater = true if printer["gcode_macro RatOS"].chamber_heater_control_external_heater|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_enable = true if printer["gcode_macro RatOS"].chamber_heater_air_circulation_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_fan_speed = printer["gcode_macro RatOS"].chamber_heater_air_circulation_fan_speed|default(0.35)|float %}
	{% set chamber_heater_air_circulation_y_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_y_pos|default(0)|float %}
	{% set chamber_heater_air_circulation_z_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_z_pos|default(100)|float %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_HEATER_ON" MSG="chamber_heater_enable: {chamber_heater_enable}, chamber_heater_preheating_temp: {chamber_heater_preheating_temp}, chamber_heater_heating_temp_offset: {chamber_heater_heating_temp_offset}, bed_temp: {bed_temp}, chamber_temp: {chamber_temp}, start_chamber_temp: {start_chamber_temp}"
	
	
	{% if chamber_heater_enable and chamber_temp > 0 and chamber_heater_bed_temp > 0 %}
	
	
	_LED_HEATING
	
	
	RATOS_ECHO MSG="Preheating chamber to {(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}°C..."
	
	
	{% set chamber_temp_sensor = "extruder" %}
	{% if printer["dual_carriage"] is defined and default_toolhead == 1 %}
	{% set chamber_temp_sensor = "extruder1" %}
	{% endif %}
	{% if printer["temperature_sensor chamber"] is defined %}
	{% set chamber_temp_sensor = "temperature_sensor chamber" %}
	{% endif %}
	
	
	{% set current_chamber_temp = printer['%s' % chamber_temp_sensor].temperature|int %}
	
	
	{% set needs_heating = current_chamber_temp < (start_chamber_temp if start_chamber_temp > 0 else chamber_temp) %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_BEFORE_PREHEATING
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	{% if not is_from_start_print %}
	MAYBE_HOME
	{% endif %}
	G0 Z{chamber_heater_air_circulation_z_pos} F{z_speed}
	G0 Y{chamber_heater_air_circulation_y_pos} F{speed}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * chamber_heater_air_circulation_fan_speed)}
	{% endif %}
	{% else %}
	{% if is_from_start_print %}
	G0 Z{z} F{z_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE={chamber_temp}
	
	
	{% if needs_heating %}
	
	
	M140 S{chamber_heater_bed_temp}
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={chamber_heater_preheating_temp}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	
	{% endif %}
	
	
	{% if needs_heating %}
	_CHAMBER_HEATER_EXTRA_FAN_ON
	{% endif %}
	
	
	{% if needs_heating %}
	TEMPERATURE_WAIT SENSOR="{chamber_temp_sensor}" MINIMUM={(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% endif %}
	
	
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED=0
	_CHAMBER_FILTER_ON AT="before_print_start"
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	G28 Z
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_AFTER_PREHEATING
	{% endif %}
	
	
	{% if printer["temperature_sensor chamber"] is defined %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined and chamber_heater_control_external_heater %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	
	
	_LED_SUCCESS
	
	{% endif %}

[gcode_macro _CHAMBER_HEATER_OFF]
gcode = 
	RATOS_ECHO MSG="Deactivating chamber heater..."
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=0
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE=0
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	
	
	_CHAMBER_HEATER_EXTRA_FAN_OFF

[delayed_gcode _CHAMBER_HEATER_CONTROL]
initial_duration = 0.
gcode = 
	
	{% set chamber_temp = printer["gcode_macro _CHAMBER_HEATER_ON"].chamber_temp|default(0)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	
	
	{% set current_chamber_temp = printer['temperature_sensor chamber'].temperature|int %}
	
	
	{% if current_chamber_temp < chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	{% endif %}
	
	
	{% if current_chamber_temp >= chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_ON]
gcode = 
	
	{% set chamber_heater_extra_fan_speed = printer["gcode_macro RatOS"].chamber_heater_extra_fan_speed|default(0.0)|float %}
	
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	{% if chamber_heater_extra_fan_speed > 0 %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED={chamber_heater_extra_fan_speed}
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_OFF]
gcode = 
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED=0
	{% endif %}

[gcode_macro _USER_CHAMBER_HEATER_BEFORE_PREHEATING]
description = Will be executed before chamber preheating, only if heating is needed.
gcode = 

[gcode_macro _USER_CHAMBER_HEATER_AFTER_PREHEATING]
description = Will be executed after chamber preheating, only if heating was needed.
gcode = 

[gcode_macro RESET_HEATSOAK_SETTINGS]
description = Resets all heatsoak-related settings to startup defaults
gcode = 
	HEATSOAK_SETTINGS ACTION=reset

[gcode_macro USE_ADAPTIVE_HEATSOAK]
description = Temporarily enables adaptive bed heatsoaking (if a beacon probe is present), will reset to printer.cfg settings
	when Klipper is restarted. Optionally specify QUALITY (1-5) and maximum FIRST_LAYER_DURATION (in minutes).
	Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.QUALITY|default("1..5") %}
	{% set _ = params.FIRST_LAYER_DURATION|default("1..120 minutes") %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("Adaptive heatsoaking is only available when a beacon probe is configured.") }
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_quality = (settings.variable_beacon_adaptive_heat_soak_layer_quality if defsrc == 'startup' else current.beacon_adaptive_heat_soak_layer_quality)|default(3)|int %}
	{% set default_first_layer_duration_secs = (settings.variable_beacon_adaptive_heat_soak_maximum_first_layer_duration if defsrc == 'startup' else current.beacon_adaptive_heat_soak_maximum_first_layer_duration)|default(1800)|int %}
	{% if params2.QUALITY is defined %}
	{% set quality = params2.QUALITY|int %}
	{% if quality < 1 or quality > 5 %}
	{ action_raise_error("QUALITY must be between 1 (rough) and 5 (maximum). Use 3 (normal) if unsure.") }
	{% endif %}
	{% else %}
	{% set quality = default_quality %}
	{% endif %}
	{% if params2.FIRST_LAYER_DURATION is defined %}
	{% set first_layer_duration_mins = params2.FIRST_LAYER_DURATION|float %}
	{% if first_layer_duration_mins <= 0 %}
	{ action_raise_error("FIRST_LAYER_DURATION must be a positive number specifying the maximum first layer duration in minutes.") }
	{% endif %}
	{% if first_layer_duration_mins > 120 %}
	CONSOLE_ECHO MSG="FIRST_LAYER_DURATION will be limited to 120 minutes. Values larger than this will not have an effect on soak time."
	{% set first_layer_duration_mins = 120 %}
	{% endif %}
	{% set first_layer_duration_secs = (first_layer_duration_mins * 60.0)|int %}
	{% else %}
	{% set first_layer_duration_secs = default_first_layer_duration_secs %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	{% endif %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=True beacon_adaptive_heat_soak_layer_quality={quality} beacon_adaptive_heat_soak_maximum_first_layer_duration={first_layer_duration_secs}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."

[gcode_macro USE_FIXED_HEATSOAK]
description = Temporarily enables fixed bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
	Optionally specify DURATION (in minutes). Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.DURATION|default("0..720 minutes") %}
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_duration = (settings.variable_bed_heat_soak_time if defsrc == 'startup' else current.bed_heat_soak_time)|default(0)|int %}
	{% if params2.DURATION is defined %}
	{% set duration_mins = params2.DURATION|float %}
	{% if duration_mins < 0 %}
	{ action_raise_error("DURATION must be a non-negative number specifying the heatsoak duration in minutes.") }
	{% endif %}
	{% if duration_mins > 720 %}
	CONSOLE_ECHO MSG="DURATION will be limited to 720 minutes (12 hours). If you really need a larger value, adjust printer.cfg instead."
	{% set duration_mins = 720 %}
	{% endif %}
	{% set duration_secs = (duration_mins * 60.0)|int %}
	{% else %}
	{% set duration_secs = default_duration %}
	{% set duration_mins = duration_secs / 60.0 %}
	{% endif %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% if has_beacon %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=False bed_heat_soak_time={duration_secs}
	{% else %}
	HEATSOAK_SETTINGS QUIET=1 bed_heat_soak_time={duration_secs}
	{% endif %}
	{% if duration_mins < 1e-3 %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% else %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% endif %}

[gcode_macro USE_NO_HEATSOAK]
description = Temporarily disables bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
gcode = 
	USE_FIXED_HEATSOAK DURATION=0

[gcode_macro HEATSOAK_SETTINGS]
description = Shows or adjusts heatsoak settings
	- With no arguments: shows current heatsoak settings, specify VERBOSE=1 for detailed output
	- With arguments: sets the specified settings. Use the full setting name without the variable_ prefix, e.g. bed_heat_soak_time=300 or beacon_adaptive_heat_soak_layer_quality=4. See printer.cfg for available settings.
variable_default_source = "startup"
gcode = 
	
	{% set params2 = params %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% set quiet = params2.pop("QUIET", None)|default("0") in ("1", "true", "yes") %}
	{% set verbose = params2.pop("VERBOSE", None)|default("0") in ("1", "true", "yes") %}
	{% if has_beacon %}
	{% set vars = (
	"beacon_adaptive_heat_soak",
	"beacon_adaptive_heat_soak_max_wait",
	"beacon_adaptive_heat_soak_extra_wait_after_completion",
	"beacon_adaptive_heat_soak_layer_quality",
	"beacon_adaptive_heat_soak_maximum_first_layer_duration",
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% else %}
	{% set vars = (
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% endif %}
	{% set action = "show" if params|length == 0 else params2.ACTION %}
	{% if action is defined and params|length > 1 %}
	{ action_raise_error("ACTION cannot be specified with other parameters.") }
	{% elif action is not defined %}
	{% for k, v in params2.items() %}
	{% set k = k|lower %}
	{% if k in vars %}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Setting {k} to {v}"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={k} VALUE={v}
	{% else %}
	{ action_raise_error("Parameter '%s' is not recognised. Note that adaptive heatsoaking settings can only be set when a beacon probe is configured." % k) }
	{% endif %}
	{% endfor %}
	{% elif action == "reset" %}
	_RESET_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	CONSOLE_ECHO MSG="Heatsoak settings have been reset to their original values."
	{% elif action == "show" %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% set is_adaptive = False if not has_beacon else current.beacon_adaptive_heat_soak|default("")|lower == "true" %}
	{% if is_adaptive %}
	{% set quality = current.beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set first_layer_duration_secs = current.beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."
	{% elif current.bed_heat_soak_time|default(0)|int > 0 %}
	{% set duration_mins = (current.bed_heat_soak_time|int / 60.0) %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% else %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% endif %}
	{% if verbose %}
	CONSOLE_ECHO MSG="Detailed settings:"
	_SHOW_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	{% endif %}
	{% else %}
	{ action_raise_error("Action '%s' is not recognised" % action) }
	{% endif %}

[gcode_macro _LED_START_PRINTING]
gcode = 
	_LED_ACTION

[gcode_macro _LED_START_PRINTING_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_PRINTING]
gcode = 
	_LED_ON TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_PAUSE]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_ON]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_OFF]
gcode = 
	_LED_STANDBY

[gcode_macro _LED_LOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_LOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_RUNOUT]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_CLOG]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_UNLOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_UNLOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_DEACTIVATE_TOOLHEAD]
gcode = 
	_LED_OFF TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_STANDBY]
gcode = 
	_LED_STANDBY TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_WAKEUP]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_MOTORS_OFF]
gcode = 
	_LED_STANDBY
	_LED_VAOC_OFF

[gcode_macro _LED_INPUT_SHAPER_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_INPUT_SHAPER_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_BEACON_CALIBRATION_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_VAOC_ON]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=1.0 GREEN=1.0 BLUE=1.0
	{% endif %}

[gcode_macro _LED_VAOC_OFF]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=0.0 GREEN=0.0 BLUE=0.0
	{% endif %}

[gcode_macro _LED_ACTION]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_action %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SUCCESS]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_success %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_HEATING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_heating %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_COOLING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_cooling %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ERROR]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_error %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ON]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_on %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_OFF]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_off %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_STANDBY]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_standby %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}
	
	{% if toolhead >= 0 %}
	{% if printer['neopixel nozzle_led_t%s' % toolhead] is defined  %}
	SET_LED LED={'nozzle_led_t%s' % toolhead} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% else %}
	{% if printer['neopixel nozzle_led_t0'] is defined  %}
	SET_LED LED={'nozzle_led_t0'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% if printer['neopixel nozzle_led_t1'] is defined %}
	SET_LED LED={'nozzle_led_t1'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% endif %}
	
	_USER_LED_SET { rawparams }

[gcode_macro _USER_LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}

[gcode_macro LOAD_FILAMENT]
description = Loads new filament. Note: be careful with PETG, make sure you inspect the tip of your filament before loading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% if filament_name == '' or filament_type == '' %}
	{% set filament_name = 'unknown' %}
	{% set filament_type = 'unknown' %}
	{% endif %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_LOAD_FILAMENT TEMP={temp} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_LOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_LOAD_FILAMENT]
description = Load filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_LOAD_FILAMENT" MSG="TEMP={temp}"
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=load_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	_LOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	
	
	RESTORE_GCODE_STATE NAME=load_state
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament load routine complete, please check that the filament was loaded correctly."

[gcode_macro _IDEX_LOAD_FILAMENT]
description = Load filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament into T{toolhead}..."
	
	DEBUG_ECHO PREFIX="_IDEX_LOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	_LOAD_FILAMENT TOOLHEAD={toolhead} TEMP={temp} AUTOMATED={automated}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="Filament load routine for T{toolhead} complete, please check that the filament was loaded correctly."

[gcode_macro _LOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default(false)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE TOOLHEAD={toolhead}
	_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into hotend.."
	G92 E0
	G0 E{extruder_gear_to_cooling_position_distance} F{extruder_load_speed}
	G92 E0
	M400
	RATOS_ECHO MSG="Filament loaded into hotend."

[gcode_macro _LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set load_speed = printer["gcode_macro T%s" % toolhead].filament_load_speed|float * 60 %}
	{% set filament_loading_nozzle_offset = printer["gcode_macro T%s" % toolhead].filament_loading_nozzle_offset|float %}
	{% set cooling_position_to_nozzle_distance = printer["gcode_macro T%s" % toolhead].cooling_position_to_nozzle_distance|float %}
	{% set purge_after_load = printer["gcode_macro T%s" % toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into nozzle... Please wait!"
	G92 E0
	
	G0 E{cooling_position_to_nozzle_distance + filament_loading_nozzle_offset} F{load_speed}
	G92 E0
	G4 P1000
	_PURGE_FILAMENT	TOOLHEAD={toolhead} E={purge_after_load}
	RATOS_ECHO MSG="Filament loaded into nozzle!"

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"
	
	
	{% set filament_grabbing_length = printer["gcode_macro T%s" % toolhead].filament_grabbing_length|float %}
	{% set filament_grabbing_speed = printer["gcode_macro T%s" % toolhead].filament_grabbing_speed|float %}
	{% set resume_after_insert = true if printer["gcode_macro T%s" % toolhead].resume_after_insert|default(true)|lower == 'true' else false %}
	{% set enable_insert_detection = true if printer["gcode_macro T%s" % toolhead].enable_insert_detection|default(true)|lower == 'true' else false %}
	
	
	{% set current_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	
	{% if enable_insert_detection %}
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="toolhead: {toolhead}, filament_grabbing_length: {filament_grabbing_length}, filament_grabbing_speed: {filament_grabbing_speed}, current_idex_mode: {current_idex_mode}"
	
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	RATOS_ECHO MSG="Filament inserted into T{toolhead}, loading..."
	
	
	FORCE_MOVE STEPPER={'extruder%s' % ('' if toolhead == 0 else toolhead)} DISTANCE={filament_grabbing_length} VELOCITY={filament_grabbing_speed}
	M400
	
	
	{% if printer.pause_resume.is_paused %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% if resume_after_insert %}
	RESUME
	{% endif %}
	{% else %}
	{% if not printer.virtual_sdcard.is_active %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"

[gcode_macro _PURGE_BEFORE_UNLOAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set purge_before_unload = printer["gcode_macro T%s" % toolhead].purge_before_unload|float %}
	
	DEBUG_ECHO PREFIX="_PURGE_BEFORE_UNLOAD" MSG="TOOLHEAD: {toolhead}"
	
	
	{% if purge_before_unload > 0 %}
	G92 E0
	G0 E{purge_before_unload} F300
	G92 E0
	M400
	{% endif %}

[gcode_macro _PURGE_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set e = params.E|int %}
	{% set r = params.R|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_PURGE_FILAMENT" MSG="TOOLHEAD: {toolhead}, E: {e}"
	
	
	{% if e > 0 %}
	
	
	G92 E0
	G0 E{e} F300
	G92 E0
	M400
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={0.4 if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={0.4 if toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * 0.4)}
	{% endif %}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if r > 0 %}
	G92 E0
	G0 E-{r} F300
	G92 E0
	M400
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro _MOVE_TO_LOADING_POSITION]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_MOVE_TO_LOADING_POSITION" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	
	G1 X{loading_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _CLEANING_MOVE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_CLEANING_MOVE" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].parking_position is defined and printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set parking_position = printer["gcode_macro T%s" % toolhead].parking_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	{% set cleaning_position = loading_position %}
	{% if loading_position == parking_position %}
	{% if loading_position > 0 %}
	{% set cleaning_position = loading_position - 30 %}
	{% else %}
	{% set cleaning_position = loading_position + 30 %}
	{% endif %}
	{% endif %}
	
	
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _BED_MESH_SANITY_CHECK]
gcode = 
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is defined %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_start_print_true_zero_fuzzy_position %}
	CONSOLE_ECHO TYPE="error" TITLE="Defined zero reference not compatible with fuzzy true zero" MSG="Using fuzzy start print true zero position is not compatible with a defined zero_reference_position value in the [bed_mesh] section in printer.cfg._N_Please remove the zero_reference_position value from the [bed_mesh] section, or disable fuzzy true zero position in printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_start_print_true_zero_fuzzy_position: False"
	_STOP_AND_RAISE_ERROR MSG="Defined zero reference not compatible with fuzzy true zero"
	{% elif zero_ref_pos[0]|float|round != safe_home_x|float|round or zero_ref_pos[1]|float|round != safe_home_y|float|round %}
	CONSOLE_ECHO TYPE="error" TITLE="Zero reference position does not match safe home position" MSG="Please update your bed mesh zero reference position in printer.cfg, like so:_N__N_[bed_mesh]_N_zero_reference_position: {safe_home_x|float|round},{safe_home_y|float|round}_N_"
	_STOP_AND_RAISE_ERROR MSG="Zero reference position does not match safe home position"
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_bed_mesh %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact bed mesh is enabled" MSG="Beacon contact bed mesh is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_bed_mesh: False"
	{% endif %}
	
	{% if beacon_scan_method_automatic %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon 'automatic' scan method is enabled" MSG="Beacon 'automatic' scan method is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_scan_method_automatic: False"
	{% endif %}
	
	{% if beacon_contact_z_tilt_adjust %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact z-tilt adjust is enabled" MSG="Beacon contact z-tilt adjust is enabled. This is not recommended for normal use and may result in inaccurate z-tilt adjustment._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_z_tilt_adjust: False"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH]
gcode = 
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE=None
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE=None
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION {rawparams}
	{% endif %}

[gcode_macro _START_PRINT_BED_MESH]
variable_actual_true_zero_position_x = None
variable_actual_true_zero_position_y = None
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set X=[params.X0|default(-1)|float, params.X1|default(-1)|float] %}
	{% set Y=[params.Y0|default(-1)|float, params.Y1|default(-1)|float] %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_BED_MESH" MSG="idex_mode: {idex_mode}, X: {X}, Y: {Y}"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is not defined %}
	{% set zero_ref_pos = [safe_home_x if actual_true_zero_position_x is none else actual_true_zero_position_x, safe_home_y if actual_true_zero_position_y is none else actual_true_zero_position_y] %}
	{% endif %}
	
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	
	
	
	
	{% set X=[0, printable_x_max] %}
	{% endif %}
	
	
	{% set beacon_bed_mesh_scv = printer["gcode_macro RatOS"].beacon_bed_mesh_scv|default(25)|int %}
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% if printer.fastconfig.settings.beacon is defined and not beacon_contact_bed_mesh %}
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={beacon_bed_mesh_scv}
	{% endif %}
	
	
	{% set default_profile = printer["gcode_macro RatOS"].bed_mesh_profile|default('ratos') %}
	{% if printer["gcode_macro RatOS"].calibrate_bed_mesh|lower == 'true' %}
	BED_MESH_CLEAR
	{% if printer["gcode_macro RatOS"].adaptive_mesh|lower == 'true' %}
	CALIBRATE_ADAPTIVE_MESH PROFILE="{default_profile}" X0={X[0]} X1={X[1]} Y0={Y[0]} Y1={Y[1]} T={params.T|int} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={idex_mode} ZERO_REF_POS_X={zero_ref_pos[0]} ZERO_REF_POS_Y={zero_ref_pos[1]}
	{% else %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	BED_MESH_PROFILE LOAD="{default_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	
	{% elif printer["gcode_macro RatOS"].bed_mesh_profile is defined %}
	BED_MESH_CLEAR
	BED_MESH_PROFILE LOAD="{printer["gcode_macro RatOS"].bed_mesh_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"

[gcode_macro CALIBRATE_ADAPTIVE_MESH]
gcode = 
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set default_profile = params.PROFILE %}
	
	
	{% set x0 = params.X0|default(-1)|float %}
	{% set y0 = params.Y0|default(-1)|float %}
	{% set x1 = params.X1|default(-1)|float %}
	{% set y1 = params.Y1|default(-1)|float %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Received coordinates X0={x0|round(1)} Y0={y0|round(1)} X1={x1|round(1)} Y1={y1|round(1)}"
	
	{% if x0 >= x1 or y0 >= y1 %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Invalid coordinates received. Please check your slicer settings. Falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	
	
	{% if params.ZERO_REF_POS_X is defined and params.ZERO_REF_POS_Y is defined %}
	{% set zero_ref_pos_x = params.ZERO_REF_POS_X|float %}
	{% set zero_ref_pos_y = params.ZERO_REF_POS_Y|float %}
	{% if zero_ref_pos_x < x0 or zero_ref_pos_x > x1 or zero_ref_pos_y < y0 or zero_ref_pos_y > y1 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Zero reference position X={zero_ref_pos_x|round(1)} Y={zero_ref_pos_y|round(1)} is outside the mesh region, expanding mesh region to include it."
	{% set x0 = [x0, zero_ref_pos_x]|min %}
	{% set y0 = [y0, zero_ref_pos_y]|min %}
	{% set x1 = [x1, zero_ref_pos_x]|max %}
	{% set y1 = [y1, zero_ref_pos_y]|max %}
	{% endif %}
	{% endif %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float %}
	
	
	{% set mesh_x0 = [[x0, max_x]|min, min_x]|max %}
	{% set mesh_y0 = [[y0, max_y]|min, min_y]|max %}
	{% set mesh_x1 = [[x1, max_x]|min, min_x]|max %}
	{% set mesh_y1 = [[y1, max_y]|min, min_y]|max %}
	
	{% if mesh_x0 == min_x and mesh_y0 == min_y and mesh_x1 == max_x and mesh_y1 == max_y %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Print is using the full bed, falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	
	{% set probe_count_x = mesh_config.probe_count.split(",")[0]|int %}
	{% if mesh_config.probe_count.split(",")|length == 2 %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[1]|int %}
	{% else %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[0]|int %}
	{% endif %}
	
	
	{% set probe_x_step = (max_x - min_x) / probe_count_x %}
	{% set probe_y_step = (max_y - min_y) / probe_count_y %}
	
	
	{% set mesh_count_x = ([(mesh_x1 - mesh_x0) / probe_x_step, 3]|max)|int %}
	{% set mesh_count_y = ([(mesh_y1 - mesh_y0) / probe_y_step, 3]|max)|int %}
	{% set min_mesh_count = [mesh_count_x, mesh_count_y]|min %}
	{% set max_mesh_count = [mesh_count_x, mesh_count_y]|max %}
	
	
	{% set algorithm = mesh_config.algorithm %}
	{% if algorithm|lower == 'lagrange' and max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="cannot exceed a probe_count of 6 when using lagrange interpolation. Falling back to bicubic interpolation."
	{% set algorithm = 'bicubic' %}
	{% endif %}
	{% if algorithm|lower == 'bicubic' and min_mesh_count < 4 %}
	{% if max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="invalid probe_count option when using bicubic interpolation. Combination of 3 points on one axis with more than 6 on another is not permitted. Forcing minimum mesh count to be 4."
	{% set min_mesh_count = 4 %}
	{% else %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="bicubic interpolation with a probe_count of less than 4 points detected. Forcing lagrange interpolation."
	{% set algorithm = 'lagrange' %}
	{% endif %}
	{% endif %}
	
	{% set mesh_count_x = ([min_mesh_count, mesh_count_x]|max)|int %}
	{% set mesh_count_x = ([max_mesh_count, mesh_count_x]|min)|int %}
	{% set mesh_count_y = ([min_mesh_count, mesh_count_y]|max)|int %}
	{% set mesh_count_y = ([max_mesh_count, mesh_count_y]|min)|int %}
	
	{% set should_prime = printer["gcode_macro RatOS"].nozzle_priming == 'primeblob' %}
	{% if printer["dual_carriage"] is not defined %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% else %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 != 0 and probe_first %}
	{% set probe_first = false %}
	{% elif printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 == 0 and not probe_first %}
	{% set probe_first = true %}
	{% endif %}
	
	
	{% if should_prime and probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="mesh coordinates X0={mesh_x0|round(1)} Y0={mesh_y0|round(1)} X1={mesh_x1|round(1)} Y1={mesh_y1|round(1)}"
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y} RELATIVE_REFERENCE_INDEX=-1
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	
	
	{% if should_prime and not probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro M84]
rename_existing = M84.1
gcode = 
	
	M84.1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_OFFSET X=0 Y=0
	
	
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro _VAOC"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False
	{% endif %}
	
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	SET_SKEW CLEAR=1
	
	
	_LED_MOTORS_OFF

[gcode_macro M104]
rename_existing = M104.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M104" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set temperature_offset_t0 = printer["gcode_macro T0"].temperature_offset|default(0)|int %}
	{% set temperature_offset_t1 = printer["gcode_macro T1"].temperature_offset|default(0)|int %}
	{% set s0 = [s + temperature_offset_t0, 0]|max %}
	{% set s1 = [s + temperature_offset_t1, 0]|max %}
	{% if temperature_offset_t0 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t0}°C added to toolhead T0."
	{% endif %}
	{% if temperature_offset_t1 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t1}°C added to toolhead T1."
	{% endif %}
	{% else %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	M104.1 S{s0} T0
	M104.1 S{s1} T1
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% else %}
	M104.1 S{s} T{t}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M109]
rename_existing = M109.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M109" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M109" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	M109.1 S{s} T{t}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro SET_HEATER_TEMPERATURE]
rename_existing = SET_HEATER_TEMPERATURE_BASE
gcode = 
	
	{% set heater = params.HEATER|default("") %}
	{% set target = params.TARGET|default(0)|int %}
	
	DEBUG_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="heater: {heater}, target: {target}"
	
	{% set t = -1 %}
	{% if heater|lower == "extruder" or heater|lower == "extruder1" %}
	
	{% set t = 0 if heater|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and target > 0 %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set target = [target + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE_BASE HEATER="{heater}" TARGET={target}
	
	{% if t != -1 and printer.fastconfig.settings.beacon is defined %}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro TEMPERATURE_WAIT]
rename_existing = TEMPERATURE_WAIT_BASE
gcode = 
	
	{% set sensor = params.SENSOR|default("") %}
	{% set minimum = params.MINIMUM|default(-1)|int %}
	{% set maximum = params.MAXIMUM|default(-1)|int %}
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="sensor: {sensor}, minimum: {minimum}, maximum: {maximum}"
	
	{% set t = -1 %}
	{% if sensor|lower == "extruder" or sensor|lower == "extruder1" %}
	
	{% set t = 0 if sensor|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and (minimum > 0 or maximum > 0) %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% if minimum > -1 %}
	{% set minimum = [minimum + temperature_offset, 0]|max %}
	{% endif %}
	{% if maximum > -1 %}
	{% set maximum = [maximum + temperature_offset, 0]|max %}
	{% endif %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set id = "sensor " ~ sensor if t == -1 else "toolhead T" ~ t %}
	
	
	{% if minimum > -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum} MAXIMUM={maximum}
	{% elif minimum > -1 and maximum == -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum}
	{% elif minimum == -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MAXIMUM={maximum}
	{% else %}
	
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="neither MINIMUM or MAXIMUM args were specified, call TEMPERATURE_WAIT_BASE is expected to fail"
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}"
	{% endif %}
	
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature for {id} reached."

[gcode_macro SDCARD_PRINT_FILE]
rename_existing = SDCARD_PRINT_FILE_BASE
gcode = 
	{% if printer["ratos"] is defined %}
	PROCESS_GCODE_FILE { rawparams }
	{% else %}
	SDCARD_PRINT_FILE_BASE { rawparams }
	{% endif %}

[gcode_macro SKEW_PROFILE]
rename_existing = SKEW_PROFILE_BASE
variable_loaded_profile = ""
gcode = 
	{% if params.LOAD is defined %}
	{% if printer.fastconfig.settings["skew_correction %s" % params.LOAD] is defined %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='"{params.LOAD}"'
	{% endif %}
	{% endif %}
	
	SKEW_PROFILE_BASE { rawparams }

[gcode_macro SET_SKEW]
rename_existing = SET_SKEW_BASE
gcode = 
	{% if params.CLEAR is defined %}
	{% if params.CLEAR|default(0)|int == 1 %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='""'
	{% endif %}
	{% endif %}
	
	SET_SKEW_BASE { rawparams }

[gcode_macro SET_VELOCITY_LIMIT]
rename_existing = SET_VELOCITY_LIMIT_BASE
gcode = 
	{% if params.ACCEL_TO_DECEL is defined %}
	
	{% if params.ACCEL is defined %}
	{% set accel = params.ACCEL|float %}
	{% else %}
	{% set accel = printer.toolhead.max_accel|float %}
	{% endif %}
	
	{% if params.VELOCITY is defined %}
	{% set velocity = params.VELOCITY|float %}
	{% else %}
	{% set velocity = printer.toolhead.max_velocity|float %}
	{% endif %}
	
	{% if params.SQUARE_CORNER_VELOCITY is defined %}
	{% set scv = params.SQUARE_CORNER_VELOCITY|float %}
	{% else %}
	{% set scv = printer.toolhead.square_corner_velocity|float %}
	{% endif %}
	
	{% set mcr = params.ACCEL_TO_DECEL|float / accel %}
	
	DEBUG_ECHO PREFIX="SET_VELOCITY_LIMIT" MSG="ACCEL={accel}, VELOCITY={velocity}, SQUARE_CORNER_VELOCITY={scv}, MINIMUM_CRUISE_RATIO={mcr}"
	
	SET_VELOCITY_LIMIT_BASE ACCEL={accel} VELOCITY={velocity} SQUARE_CORNER_VELOCITY={scv} MINIMUM_CRUISE_RATIO={1-mcr}
	
	{% else %}
	
	SET_VELOCITY_LIMIT_BASE { rawparams }
	
	{% endif %}

[gcode_macro BED_MESH_CALIBRATE]
rename_existing = _BED_MESH_CALIBRATE_BASE
variable_abl_and_home_z_if_required = True
gcode = 
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	{% if abl_and_home_z_if_required %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% endif %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set beacon_default_probe_method = printer.fastconfig.settings.beacon.default_probe_method|default('proximity') %}
	{% set probe_method = params.PROBE_METHOD|default(beacon_default_probe_method)|lower %}
	{% if probe_method == 'proximity' %}
	_CHECK_ACTIVE_BEACON_MODEL_TEMP TITLE="Bed mesh calibration warning"
	{% endif %}
	{% endif %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_BED_MESH_CALIBRATE_BASE {rawparams}
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	_APPLY_RATOS_BED_MESH_PARAMETERS {rawparams}
	{% endif %}

[gcode_macro SET_GCODE_OFFSET]
rename_existing = SET_GCODE_OFFSET_BASE
gcode = 
	DEBUG_ECHO PREFIX="SET_GCODE_OFFSET" MSG="{rawparams|replace('"', '')|replace("'", '')}"
	{% set z_before = printer.gcode_move.homing_origin.z|float %}
	SET_GCODE_OFFSET_BASE {rawparams}
	_AFTER_SET_GCODE_OFFSET Z_BEFORE={z_before}

[gcode_macro _AFTER_SET_GCODE_OFFSET]
gcode = 
	{% set z_before = params.Z_BEFORE|float %}
	{% set z_after = printer.gcode_move.homing_origin.z|float %}
	{% if z_before != z_after %}
	_ALERT_NON_ZERO_Z_OFFSET FORCE=1
	{% endif %}

[gcode_macro _START_PRINT_PARK]
gcode = 
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_x = printer["gcode_macro RatOS"].start_print_park_x %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% if printer["gcode_macro RatOS"].start_print_park_x is defined and printer["gcode_macro RatOS"].start_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="start_print_park_x is ignored for IDEX printers"
	{% endif %}
	PARK_TOOLHEAD
	G90
	{% endif %}
	
	
	_PARK LOCATION={start_print_park_in} X={start_print_park_x}
	G0 Z{z} F{z_speed}

[gcode_macro _END_PRINT_PARK]
gcode = 
	{% if printer["dual_carriage"] is defined %}
	
	{% if printer["gcode_macro RatOS"].end_print_park_x is defined and printer["gcode_macro RatOS"].end_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="end_print_park_x is ignored for IDEX printers"
	{% endif %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	PARK_TOOLHEAD
	G90
	{% endif %}
	_PARK LOCATION={printer["gcode_macro RatOS"].end_print_park_in} X={printer["gcode_macro RatOS"].end_print_park_x}

[gcode_macro _PARK]
gcode = 
	
	{% set x = params.X %}
	{% set location = params.LOCATION|default('back')|lower %}
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	{% set nozzle_priming = printer["gcode_macro RatOS"].nozzle_priming|lower %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="park"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% if x != '' %}
	{% if x|float >= printer.toolhead.axis_minimum.x + 5 and x|float <= printable_x_max - 5 %}
	{% set park_x = x|float %}
	{% else %}
	{action_respond_info('The requested X co-ordinate is outside the defined axis bounds - using defaults')}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	{% else %}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	
	
	{% set park_y = printable_y_max - 15 %}
	{% if location == 'front' %}
	{% set park_y = printer.toolhead.axis_minimum.y + 5 %}
	{% elif location == 'center' %}
	{% set park_y = printable_y_max / 2 %}
	{% elif location == 'primeblob' and printer["dual_carriage"] is defined %}
	
	{% set park_y = printable_y_max - 15 %}
	{% endif %}
	
	
	{% if location == 'primeblob' and printer["dual_carriage"] is not defined %}
	{% if (nozzle_priming == 'primeblob' or nozzle_priming == 'primeline') %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set park_x = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set park_x = printable_x_max - 5 %}
	{% else %}
	{% set park_x = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set park_y = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set park_y = printable_y_max - 5 %}
	{% else %}
	{% set park_y = nozzle_prime_start_y|float %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	G0 X{park_x} Y{park_y} F{speed}
	{% else %}
	
	G0 Y{park_y} F{speed}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="park"

[gcode_macro SAVE_PROBE_RESULT]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	{% set last_z_offset = 9999.9 %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if beacon_contact_prime_probing %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	{% else %}
	{% set last_z_offset = printer.beacon.last_sample.dist - current_z %}
	{% endif %}
	{% elif printer.fastconfig.settings.bltouch is defined  %}
	{% set config_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% elif printer.fastconfig.settings.probe is defined  %}
	{% set config_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% endif %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Saving offset adjustment of {last_z_offset} in {params.VARIABLE|default('last_z_offset')}"
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={params.VARIABLE|default('last_z_offset')} VALUE={last_z_offset}

[gcode_macro PROBE_FOR_PRIMING]
gcode = 
	
	{% set probe_for_priming_disable_mesh_constraints = true if printer["gcode_macro RatOS"].probe_for_priming_disable_mesh_constraints|default(false)|lower == 'true' else false %}
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower != 'false' %}
	SAVE_GCODE_STATE NAME=probe_for_priming_state
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the prime location.."
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set t = params.TOOLHEAD|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% if idex_mode == '' %}
	
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% if t == 0 %}
	{% set x_start = 5 %}
	{% else %}
	{% set x_start = printable_x_max - 5 %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% endif %}
	{% endif %}
	{% set z = printer.fastconfig.settings.bed_mesh.horizontal_move_z|float %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% if printer.fastconfig.settings.bltouch is defined %}
	{% set x_offset = printer.fastconfig.settings.bltouch.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.bltouch.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% elif printer.fastconfig.settings.probe is defined %}
	{% set x_offset = printer.fastconfig.settings.probe.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.probe.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% elif printer.fastconfig.settings.beacon is defined %}
	{% set x_offset = printer.fastconfig.settings.beacon.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.beacon.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.beacon.trigger_distance|float %}
	{% else %}
	{ action_raise_error("No probe, beacon or bltouch section found. Adaptive priming only works with a [probe], [beacon] or [bltouch] section defined.") }
	{% endif %}
	
	{% if z < z_offset %}
	{ action_raise_error("Horizontal move Z ({z}) is below your probe's Z offset ({z_offset}). Please adjust your horizontal_move_z setting in [bed_mesh] to be above {z}.") }
	{% endif %}
	
	{% if not probe_for_priming_disable_mesh_constraints %}
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float - x_offset %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float - y_offset %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float - x_offset %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float - y_offset %}
	
	
	{% set x_start = [[x_start, max_x]|min, min_x]|max %}
	{% set y_start = [[y_start, max_y]|min, min_y]|max %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the start of the prime location at {x_start}, {y_start}"
	
	G90
	
	M83
	
	G0 Z{z} F{z_speed}
	
	G1 X{x_start} Y{y_start} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result
	{% endif %}
	
	{% if idex_mode == '' %}
	
	{% set x_end = x_start %}
	{% set y_end = y_start + 45 %}
	{% else %}
	
	{% if t==1 %}
	{% set x_end = x_start - 45 %}
	{% else %}
	{% set x_end = x_start + 45 %}
	{% endif %}
	{% set y_end = y_start %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the end of the prime location at {x_end}, {y_end}"
	G1 X{x_end} Y{y_end} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result
	{% endif %}
	
	RESTORE_GCODE_STATE NAME=probe_for_priming_state
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	{% endif %}

[gcode_macro RESET_PRIME_PROBE_STATE]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result VALUE=None
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result_t1 VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result_t1 VALUE=None
	{% endif %}

[gcode_macro PROBE_CURRENT_POSITION]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	SAVE_GCODE_STATE NAME=probe_current_position_state
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	ASSERT_PROBE_DEPLOYED
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_prime_probing %}
	PROBE PROBE_METHOD=contact SAMPLES=1
	{% else %}
	PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	BEACON_QUERY
	{% else %}
	
	RESTORE_GCODE_STATE NAME=probe_current_position_state MOVE=1 MOVE_SPEED={printer["gcode_macro RatOS"].macro_z_speed|float}
	{% endif %}

[gcode_macro PRIME_BLOB]
description = Prints a primeblob, used internally, if configured, as part of the START_PRINT macro.
variable_x_offset = 5
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="prime_blob"
	SET_MACRO_TRAVEL_SETTINGS
	
	RATOS_ECHO PREFIX="Priming" MSG="Priming nozzle with prime blob.."
	
	
	{% set current_toolhead = 0 %}
	
	
	{% set target_idex_mode = '' %}
	{% set extruder = 'extruder' %}
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE is defined %}
	{% set target_idex_mode = params.IDEX_MODE|default('')|lower %}
	{% else %}
	{ action_raise_error("IDEX_MODE parameter not found for PRIME_BLOB macro. This is likely a bug.") }
	{% endif %}
	RATOS_ECHO PREFIX="Priming" MSG="Priming in IDEX {target_idex_mode} mode.."
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set current_toolhead = 1 if current_idex_mode=='primary' else 0 %}
	{% set extruder = 'extruder1' if current_toolhead == 1 else 'extruder' %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	SAVE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set fan_speed = printer["gcode_macro RatOS"].nozzle_prime_bridge_fan|float %}
	{% set nozzle_diameter = printer.fastconfig.settings[extruder].nozzle_diameter|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set has_start_offset_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) != 9999.9 %}
	{% if printer["dual_carriage"] is defined %}
	{% set has_start_offset_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) != 9999.9 %}
	{% endif %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_z_height = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set nozzle_prime_direction = printer["gcode_macro RatOS"].nozzle_prime_direction|lower %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% if target_idex_mode == '' %}
	
	{% set x_factor = 0 %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% set y_factor = -1 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% if nozzle_prime_start_y|float < printable_y_max / 2 %}
	{% set y_factor = 1 %}
	{% else %}
	{% set y_factor = -1 %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_direction == 'forwards' %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_direction == 'backwards' %}
	{% set y_factor = -1 %}
	{% endif %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% else %}
	{% set z = start_print_park_z_height %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% set y_factor = 0 %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set x_start = center_x / 2 + 5 %}
	{% set x_factor = 1 %}
	{% else %}
	
	
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% if current_toolhead == 0 %}
	{% set x_start = 55 %}
	{% set x_factor = -1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 55 %}
	{% set x_factor = 1 %}
	{% endif %}
	{% else %}
	{% if current_toolhead == 0 %}
	{% set x_start = 5 %}
	{% set x_factor = 1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 5 %}
	{% set x_factor = -1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_x_max - 5 %}
	{% endif %}
	{% set z = 10 %}
	{% endif %}
	
	{% set start_z_offset = 0 %}
	{% set end_z_offset = 0 %}
	{% if has_start_offset_t0 %}
	{% set start_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) %}
	{% set end_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_end_result|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t0) ) }
	{% endif %}
	{% if end_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t0) )  }
	{% endif %}
	{% set start_z_offset = start_z_probe_result_t0 %}
	{% set end_z_offset = end_z_probe_result_t0 %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	{% if current_toolhead == 1 or both_toolheads or target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	{% if has_start_offset_t1 %}
	{% set start_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) %}
	{% set end_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_end_result_t1|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t1) ) }
	{% endif %}
	{% if end_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t1) ) }
	{% endif %}
	{% set start_z_offset = [start_z_offset, start_z_probe_result_t1]|max %}
	{% set end_z_offset = [end_z_offset, start_z_probe_result_t1]|max %}
	{% endif %}
	{% endif %}
	{% if target_idex_mode != 'copy' and target_idex_mode != 'mirror' %}
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% set original_start_z_offset = start_z_offset %}
	{% set original_end_z_offset = end_z_offset %}
	{% set start_z_offset = original_end_z_offset %}
	{% set end_z_offset = original_start_z_offset %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	DEBUG_ECHO PREFIX="PRIME_BLOB" MSG="x_start: {x_start}, y_start: {y_start}, x_factor: {x_factor}, y_factor: {y_factor}, z: {z}, start_z_offset: {start_z_offset}, end_z_offset: {end_z_offset}"
	
	
	G90
	
	M83
	RATOS_ECHO PREFIX="Priming" MSG="Lifting Z to {z}.."
	
	G0 Z{z} F{z_speed}
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% if start_print_park_in != 'primeblob' %}
	G1 X{x_start} F{speed}
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% endif %}
	{% else %}
	
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% if target_idex_mode=="copy" or target_idex_mode=="mirror" %}
	RATOS_ECHO PREFIX="Priming" MSG="Mirroring move to {x_start}, {y_start} along the edge of the print area.."
	
	_IDEX_MIRROR PRIMING=1
	{% else %}
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% endif %}
	G1 X{x_start} F{speed}
	{% endif %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Starting prime blob.."
	
	G1 Z{0.5 + start_z_offset} F{z_speed}
	
	G1 Y{y_start} F{speed}
	
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	
	M106 S{fan_speed}
	
	G1 Z5 F100 E5
	G92 E0
	RATOS_ECHO PREFIX="Priming" MSG="Bridging with {((fan_speed/255) * 100)|int}% fan speed.."
	
	G1 F3000 X{x_start + (15 * x_factor)} Y{y_start + (15 * y_factor)} E{1 / ((0.4 / nozzle_diameter) ** 2)}
	
	
	
	G1 F3000 X{x_start + (20 * x_factor)} Y{y_start + (20 * y_factor)} Z{3.8 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (34 * x_factor)} Y{y_start + (34 * y_factor)} Z{2.6 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (38 * x_factor)} Y{y_start + (38 * y_factor)} Z{1.4 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (42 * x_factor)} Y{y_start + (42 * y_factor)} Z{0.2 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	
	M106 S0
	
	G1 F3000 X{x_start + (46 * x_factor)} Y{y_start + (46 * y_factor)} Z{0.2 + end_z_offset} E0.6
	
	G1 F{speed} X{x_start + (50 * x_factor)} Y{y_start + (50 * y_factor)}
	
	
	{% if target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if target_idex_mode == "copy" %}
	{% if first_y >= 0 %}
	_IDEX_COPY DANCE=0 Y={first_y}
	{% else %}
	_IDEX_COPY DANCE=0 Y={params.Y1}
	{% endif %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	RESTORE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="prime_blob"
	
	
	G92 E0

[gcode_macro UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set temp = params.TEMP|default(220)|int %}
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_UNLOAD_FILAMENT TEMP={temp} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_UNLOAD_FILAMENT]
description = Unload filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_UNLOAD_FILAMENT" MSG="TEMP: {temp}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=unload_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	G4 P3000
	
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD=0 NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=unload_state
	
	
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament unloading completed"

[gcode_macro _IDEX_UNLOAD_FILAMENT]
description = Unload filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading T{toolhead} filament..."
	
	DEBUG_ECHO PREFIX="_IDEX_UNLOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} AUTOMATED={automated}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="T{toolhead} filament unloading completed"

[gcode_macro _UNLOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LEGACY_UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
gcode = 
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set unload_speed = 5 * 60 %}
	{% set unload_length = printer["gcode_macro RatOS"].filament_unload_length|float %}
	M117 Unloading filament...
	
	G0 E10 F300
	
	G0 E-5 F3600
	
	G4 P3000
	
	G0 E5 F6000
	
	G0 E-15 F6000
	
	G0 E-{unload_length} F{unload_speed}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}
	M117 Filament unloaded!
	RESPOND MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	RATOS_ECHO MSG="Unloading filament from nozzle to cooling zone... Please wait!"
	
	_PURGE_BEFORE_UNLOAD TOOLHEAD={toolhead}
	
	{% if printer["gcode_macro _UNLOAD_WITHOUT_TIP_FORMING"] is defined %}
	
	_UNLOAD_WITHOUT_TIP_FORMING TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	_UNLOAD_WITH_TIP_FORMING NAME='{filament_name}' TYPE='{filament_type}'
	{% endif %}
	
	G4 P3000

[gcode_macro _UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	{% set tooolhead_sensor_to_extruder_gear_distance = printer["gcode_macro T%s" % toolhead].tooolhead_sensor_to_extruder_gear_distance|float %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER" MSG="TOOLHEAD: {toolhead}"
	
	
	G0 E-{extruder_gear_to_cooling_position_distance + tooolhead_sensor_to_extruder_gear_distance + 50} F{extruder_load_speed}
	
	RATOS_ECHO MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_WITH_TIP_FORMING]
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	{% if filament_name != '' and filament_type != '' %}
	_UNLOAD_KNOWN_FILAMENT NAME={filament_name} TYPE={filament_type}
	{% else %}
	_UNLOAD_UNKNOWN_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _UNLOAD_KNOWN_FILAMENT]
description = User overrideable tip forming macro if slicer filament profiles are known
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	RATOS_ECHO PREFIX="FILAMENT TYPE" MSG='{filament_type}'
	RATOS_ECHO PREFIX="FILAMENT PROFILE" MSG='{filament_name}'
	
	
	{% if filament_name == "Prusament PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% elif filament_name == "Nobufil PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% else %}
	
	RATOS_ECHO PREFIX="_UNLOAD_KNOWN_FILAMENT" MSG="Filament profile not found!"
	_UNLOAD_UNKNOWN_FILAMENT
	{% endif %}

[gcode_macro _UNLOAD_UNKNOWN_FILAMENT]
description = User overrideable standard tip forming macro
gcode = 
	
	DEBUG_ECHO PREFIX="_UNLOAD_UNKNOWN_FILAMENT" MSG="Using standard tip forming macro!"
	
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10

[gcode_macro _TIP_FORMING]
gcode = 
	
	{% set cooling_moves = params.COOLING_MOVES|default(4)|int %}
	{% set cooling_move_length = params.COOLING_MOVE_LENGTH|default(10)|float %}
	{% set start_cooling_speed = params.START_COOLING_SPEED|default(10)|float * 60 %}
	{% set end_cooling_speed = params.END_COOLING_SPEED|default(50)|float * 60 %}
	{% if cooling_moves == 0 %}
	{% set cooling_move_length = 0 %}
	{% endif %}
	
	
	{% set dip = true if params.DIP|default(false)|lower == "true" else false %}
	{% set dip_length = params.DIP_LENGTH|default(22)|float %}
	{% set dip_speed = params.DIP_SPEED|default(30)|float * 60 %}
	{% set dip_retract_speed = params.DIP_RETRACT_SPEED|default(70)|float * 60 %}
	
	
	{% set retract_length = params.RETRACT_LENGTH|default(18)|float %}
	{% set start_retract_speed = params.START_RETRACT_SPEED|default(120)|float * 60 %}
	{% set end_retract_speed = params.END_RETRACT_SPEED|default(20)|float * 60 %}
	
	DEBUG_ECHO PREFIX="_TIP_FORMING" MSG="cooling_moves: {cooling_moves}, cooling_move_length: {cooling_move_length}, start_cooling_speed: {start_cooling_speed}, end_cooling_speed: {end_cooling_speed}, dip: {dip}, dip_length: {dip_length}, dip_speed: {dip_speed}, dip_retract_speed: {dip_retract_speed}, retract_length: {retract_length}, start_retract_speed: {start_retract_speed}, end_retract_speed: {end_retract_speed}"
	
	M220 S100
	
	
	G92 E0
	{% set retract = retract_length + cooling_move_length / 2 - 15 %}
	G1 E-15 F{start_retract_speed}
	G1 E-{0.7 * retract} F{1.0 * end_retract_speed}
	G1 E-{0.2 * retract} F{0.5 * end_retract_speed}
	G1 E-{0.1 * retract} F{0.3 * end_retract_speed}
	
	
	G92 E0
	{% if cooling_moves > 0 %}
	{% set i = (end_cooling_speed - start_cooling_speed) / (2 * cooling_moves - 1) %}
	{% for m in range(cooling_moves) %}
	G1 E{cooling_move_length} F{(start_cooling_speed + i * m * 2)}
	G1 E-{cooling_move_length} F{(start_cooling_speed + i * (m * 2 + 1))}
	{% endfor %}
	{% endif %}
	
	
	G92 E0
	{% if dip %}
	G1 E{dip_length} F{dip_speed}
	G4 P100
	G1 E-{dip_length} F{dip_retract_speed}
	{% endif %}
	
	G92 E0
	M400

[delayed_gcode __ON_FILAMENT_SENSOR_BUTTON_PRESSED_STARTUP_GUARD]
initial_duration = 2.
gcode = 
	SET_GCODE_VARIABLE MACRO=_ON_FILAMENT_SENSOR_BUTTON_PRESSED VARIABLE=startup_complete VALUE=True

[gcode_macro _ON_FILAMENT_SENSOR_BUTTON_PRESSED]
variable_startup_complete = False
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set toolhead_sensor_button_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_sensor_button_only_when_sensor_enabled|default(false)|lower == 'true' %}
	
	
	{% if not startup_complete and sensor_enabled %}
	{action_emergency_stop("RatOS: The T%s filament sensor button was triggered immediately on printer startup. This is likely a false trigger. Please check your filament sensor wiring and configuration!" % (toolhead,))}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_SENSOR_BUTTON_PRESSED" MSG="TOOLHEAD: {toolhead}, SENSOR_ENABLED: {sensor_enabled}, TOOLHEAD_SENSOR_BUTTON_ONLY_WHEN_SENSOR_ENABLED: {toolhead_sensor_button_only_when_sensor_enabled}"
	
	{% if not printer.virtual_sdcard.is_active and (sensor_enabled or not toolhead_sensor_button_only_when_sensor_enabled) %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	{% set toolhead_detect_clog_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_detect_clog_only_when_sensor_enabled|default(true)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}, ENABLE_CLOG_DETECTION: {enable_clog_detection}, TOOLHEAD_DETECT_CLOG_ONLY_WHEN_SENSOR_ENABLED: {toolhead_detect_clog_only_when_sensor_enabled}, SENSOR_ENABLED: {sensor_enabled}"
	
	{% if enable_clog_detection and (sensor_enabled or not toolhead_detect_clog_only_when_sensor_enabled) %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_clog_detection %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_FILAMENT_END]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set clogged = true if params.CLOGGED|default(false)|lower == 'true' else false %}
	
	
	{% set unload_after_runout = printer["gcode_macro T%s" % toolhead].unload_after_runout|float %}
	
	
	{% if clogged %}
	_LED_FILAMENT_CLOG TOOLHEAD={toolhead}
	{% else %}
	_LED_FILAMENT_RUNOUT TOOLHEAD={toolhead}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_END" MSG="TOOLHEAD: {toolhead}"
	
	{% if printer.virtual_sdcard.is_active %}
	{% if not printer.pause_resume.is_paused %}
	PAUSE RUNOUT=True
	{% endif %}
	{% if not clogged and unload_after_runout %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	{% if not clogged and printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true'%}
	_JOIN_SPOOL TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M600]
description = Executes a color change by pausing the printer an unloading the filament.
gcode = 
	PAUSE
	UNLOAD_FILAMENT AUTOMATED=True
	RATOS_ECHO MSG="Please load new filament and resume"

[gcode_macro COLD_PULL]
description = Automated hotend cold pull.
gcode = 
	
	{% set extrusion_temp = params.EXTRUSION_TEMP|default(220)|int %}
	{% set cold_pull_temp = params.COLD_PULL_TEMP|default(80)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	
	{% if printer["dual_carriage"] is not defined %}
	{% set toolhead = 0 %}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead != 0 and toolhead != 1 %}
	{action_raise_error("Please select toolhead! 0 = left, 1 = right toolhead")}
	{% endif %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	RATOS_ECHO MSG="Starting cold pull on T{toolhead}..."
	{% else %}
	RATOS_ECHO MSG="Starting cold pull..."
	{% endif %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	SAVE_GCODE_STATE NAME=cold_pull_state
	
	
	{% if printer["dual_carriage"] is defined and "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	RATOS_ECHO MSG="Heating T{toolhead} to {extrusion_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={extrusion_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={extrusion_temp} MAXIMUM={extrusion_temp + 2}
	
	
	G4 P3000
	
	
	RATOS_ECHO MSG="extruding..."
	G92 E0
	G1 E30 F300
	G92 E0
	
	
	RATOS_ECHO MSG="Cooling T{toolhead} to {cold_pull_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={cold_pull_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={cold_pull_temp} MAXIMUM={cold_pull_temp + 2}
	
	
	G4 P10000
	
	
	RATOS_ECHO MSG="cold pull..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-40 VELOCITY=5 ACCEL=100
	
	
	RATOS_ECHO MSG="eject filament..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-200 VELOCITY=20 ACCEL=500
	
	
	RATOS_ECHO MSG="cooling down extruder..."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	RESTORE_GCODE_STATE NAME=cold_pull_state
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	
	CONSOLE_ECHO TITLE="Cold pull complete" MSG="Please remove the filament from the PTFE tube and cut the end off. Do NOT try to load it again." TYPE="warning"

[gcode_macro _USER_START_PRINT_BEFORE_HOMING]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_BED]
gcode = 

[gcode_macro _USER_START_PRINT_BED_MESH]
gcode = 

[gcode_macro _USER_START_PRINT_PARK]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 

[gcode_macro _USER_START_PRINT_HEAT_CHAMBER]
description = Uses the extruder sensor to wait for chamber temp. Override the _START_PRINT_HEAT_CHAMBER macro to implement heated chamber handling.
gcode = 
	
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}

[gcode_macro _USER_END_PRINT_BEFORE_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_AFTER_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_PARK]
gcode = 

[gcode_macro _USER_END_PRINT_FINISHED]
description = User hook for when the print is finished after gcode state has been restored.
gcode = 

[gcode_macro _USER_START_PRINT]
gcode = 

[gcode_macro _USER_END_START_PRINT]
gcode = 

[gcode_macro _USER_START_FEATURE]
gcode = 

[gcode_macro _USER_END_FEATURE]
gcode = 

[gcode_macro _USER_BEFORE_IDLE_TIMEOUT]
gcode = 

[gcode_macro _USER_AFTER_IDLE_TIMEOUT]
gcode = 

[gcode_macro ECHO_T_VARS]
description = Echo Toolhead variables to the console.
gcode = 
	{% set t = params.T|default(0) %}
	RATOS_ECHO MSG="T{t} Variables"
	{% for var, value in printer["gcode_macro T%s" % t].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ECHO_RATOS_VARS]
description = Echo RatOS variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro RatOS"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ENSURE_CRITICAL_RATOS_INIT]
variable_completed = False
gcode = 
	{% if not completed %}
	CALCULATE_PRINTABLE_AREA
	SET_GCODE_VARIABLE MACRO=ENSURE_CRITICAL_RATOS_INIT VARIABLE=completed VALUE=True
	{% endif %}

[delayed_gcode RATOS_INIT]
initial_duration = 0.1
gcode = 
	{action_respond_info("Initializing RatOS...")}
	ENSURE_CRITICAL_RATOS_INIT
	_LED_STANDBY
	INITIAL_FRONTEND_UPDATE
	_CHAMBER_FILTER_SANITY_CHECK
	{% if printer.fastconfig.settings.beacon is defined %}
	
	_BED_MESH_SANITY_CHECK
	{% endif %}
	{% set svv = printer.save_variables.variables %}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=0 C={svv.nozzle_expansion_coefficient_t0|default(0.06)|float}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=1 C={svv.nozzle_expansion_coefficient_t1|default(0.06)|float}
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=idex_applied_offset

[delayed_gcode RATOS_LOGO]
initial_duration = 2
gcode = 
	
	
	
	
	
	ENSURE_CRITICAL_RATOS_INIT
	HELLO_RATOS
	_ALERT_NON_ZERO_Z_OFFSET

[gcode_macro _ALERT_NON_ZERO_Z_OFFSET]
gcode = 
	{% set force = params.FORCE|default(0)|int == 1 %}
	{% set user_offset = printer.named_offsets.user_probe_z_offset.z|float %}
	{% set gcode_offset = printer.gcode_move.homing_origin.z|float %}
	{% set combined_offset = user_offset + gcode_offset %}
	
	{% if force or user_offset != 0 or gcode_offset != 0 %}
	{% set title = "User-adjusted Z-offset of %.3f mm is active" % combined_offset %}
	{% set msg = "" %}
	{% set nl = "" %}
	{% if user_offset != 0 %}
	{% set msg = msg + "beacon true zero user Z-offset: %.3f mm (to clear, use Z_OFFSET_APPLY_PROBE CLEAR=1)" % user_offset %}
	{% set nl = "_N_" %}
	{% endif %}
	{% if gcode_offset != 0 %}
	{% set msg = msg + nl + "G-code Z-offset: %.3f mm" % gcode_offset %}
	{% endif %}
	CONSOLE_ECHO TITLE="{title}" TYPE="info" MSG="{msg}"
	{% endif %}

[gcode_macro _INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE]
gcode = 
	{% set variable = params.VARIABLE|string %}
	{% set svv = printer.save_variables.variables %}
	{% set nlu_msg = "no longer used, please remove" %}
	{% if svv[variable] is defined %}
	{% set v = svv[variable]|string|replace('"', '')|replace("'", "") %}
	{% if not nlu_msg in v %}
	SAVE_VARIABLE VARIABLE={variable} VALUE='"{nlu_msg} (was {v})"'
	{% endif %}
	CONSOLE_ECHO TITLE="Deprecated ratos-variables.cfg variable" TYPE="warning" MSG="The variable {variable} is no longer used, please remove it from your ratos-variables.cfg file."
	{% endif %}

[gcode_macro _NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK]
gcode = 
	
	
	
	
	
	
	
	{% set t = params.T|int %}
	{% set c = params.C|float %}
	{% set normal_low = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_low|default(0.05)|float %}
	{% set normal_high = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_high|default(0.10)|float %}
	
	{% if c < 0 %}
	
	{action_emergency_stop("Invalid nozzle_expansion_coefficient_t%s value in ratos-variables.cfg: %.3f. It must be non-negative." % (t, c))}
	{% endif %}
	{% if c >= normal_high %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite high. Please verify that this is correct."
	{% endif %}
	{% if c <= normal_low %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite low. Please verify that this is correct."
	{% endif %}

[gcode_macro INITIAL_FRONTEND_UPDATE]
gcode = 
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_error = printer["gcode_macro RatOS"].status_color_error|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_unknown}"'
	{% endif %}
	
	
	{% set t0_sensor = "undefined" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	{% set t0_sensor = "detected" %}
	{% else %}
	{% set t0_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t0_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	{% set t1_sensor = "undefined" %}
	{% if printer["dual_carriage"] is defined and printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	{% set t1_sensor = "detected" %}
	{% else %}
	{% set t1_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t1_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	{% if svv.t0_filament is defined and printer["gcode_macro T0"] is defined %}
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	{% if t0_sensor != "empty" %}
	{% set t0_filament_type = svv.t0_filament[0]|default('')|string %}
	{% set t0_filament_name = svv.t0_filament[1]|default('')|string %}
	{% set t0_filament_temp = svv.t0_filament[2]|default(0)|float %}
	{% if t0_filament_name != '' and t0_filament_type != '' and t0_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{t0_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{t0_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={t0_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}
	{% if svv.t1_filament is defined and printer["gcode_macro T1"] is defined %}
	{% if printer["gcode_macro T1"].filament_name is defined and printer["gcode_macro T1"].filament_type is defined and printer["gcode_macro T1"].filament_temp is defined %}
	{% if t1_sensor != "empty" %}
	{% set t1_filament_type = svv.t1_filament[0]|default('')|string %}
	{% set t1_filament_name = svv.t1_filament[1]|default('')|string %}
	{% set t1_filament_temp = svv.t1_filament[2]|default(0)|float %}
	{% if t1_filament_name != '' and t1_filament_type != '' and t1_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='"{t1_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='"{t1_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE={t1_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t1_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro CALCULATE_PRINTABLE_AREA]
variable_calculated = False
gcode = 
	{% if not calculated %}
	{% set bed_margin_x = printer["gcode_macro RatOS"].bed_margin_x %}
	{% set bed_margin_y = printer["gcode_macro RatOS"].bed_margin_y %}
	
	
	
	{% set tool = 0 if printer["gcode_macro T0"] is not defined or printer["gcode_macro T0"].active else 1 %}
	{% set max_x = printer.toolhead.axis_maximum.x if printer["dual_carriage"] is defined and tool == 0 else printer.toolhead.axis_maximum.x - bed_margin_x[1] %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	
	
	{% set max_x = printer.toolhead.axis_maximum.x %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="printer.toolhead.axis_maximum.x {printer.toolhead.axis_maximum.x}"
	
	{% set max_y = printer.toolhead.axis_maximum.y - bed_margin_y[1]%}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_x_max VALUE={max_x}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_y_max VALUE={max_y}
	SET_GCODE_VARIABLE MACRO=CALCULATE_PRINTABLE_AREA VARIABLE=calculated VALUE=True
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	RATOS_LOG PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	{% endif %}

[gcode_macro CACHE_TOOLHEAD_SETTINGS]
variable_cache = {"global": {"accel": 1000, "ratio": 0.5, "speed": 50, "scv": 5}}
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set dummy = cache.__setitem__(key, {"accel": printer.toolhead.max_accel, "ratio": printer.toolhead.minimum_cruise_ratio, "speed": printer.toolhead.max_velocity, "scv": printer.toolhead.square_corner_velocity}) %}
	SET_GCODE_VARIABLE MACRO=CACHE_TOOLHEAD_SETTINGS VARIABLE=cache VALUE="{cache | pprint | replace("\n", "") | replace("\"", "\\\"")}"
	DEBUG_ECHO PREFIX="CACHE_TOOLHEAD_SETTINGS" MSG="Toolhead settings cached for {key}. {printer.toolhead.max_accel} accel, {printer.toolhead.minimum_cruise_ratio} ratio, {printer.toolhead.max_velocity} velocity, {printer.toolhead.square_corner_velocity} scv."

[gcode_macro RESTORE_TOOLHEAD_SETTINGS]
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set values = printer["gcode_macro CACHE_TOOLHEAD_SETTINGS"].cache.__getitem__(key) %}
	{% if values is not defined or values == 'None' %}
	{ action_raise_error("RESTORE_TOOLHEAD_SETTINGS: Toolhead settings not cached for key '" ~ key ~ "'.") }
	{% endif %}
	SET_VELOCITY_LIMIT ACCEL={values.accel} MINIMUM_CRUISE_RATIO={values.ratio} VELOCITY={values.speed} SQUARE_CORNER_VELOCITY={values.scv}
	DEBUG_ECHO PREFIX="RESTORE_TOOLHEAD_SETTINGS" MSG="Toolhead settings restored. {values.accel} accel, {values.ratio} ratio, {values.speed} velocity, {values.scv} scv."

[gcode_macro SET_MACRO_TRAVEL_SETTINGS]
gcode = 
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float %}
	{% set accel = printer["gcode_macro RatOS"].macro_travel_accel %}
	SET_VELOCITY_LIMIT ACCEL={accel} MINIMUM_CRUISE_RATIO=0.5 VELOCITY={speed} SQUARE_CORNER_VELOCITY={5}
	DEBUG_ECHO PREFIX="SET_MACRO_TRAVEL_SETTINGS" MSG="Macro travel settings set. {accel} accel, {speed} velocity"

[gcode_macro SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% if printer["dual_carriage"] is not defined %}
	
	SET_KINEMATIC_POSITION X={printable_x_max / 2} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	{% else %}
	
	IDEX_SET_CENTER_KINEMATIC_POSITION
	{% endif %}

[gcode_macro IDEX_SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x - (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x + (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY

[gcode_macro VERIFY_HYBRID_INVERTED]
gcode = 
	
	{% set inverted = False %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy is defined and printer.fastconfig.settings.ratos_hybrid_corexy.inverted is defined %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy.inverted|lower == 'true' %}
	{% set inverted = True %}
	{% endif %}
	{% endif %}
	{% if inverted == False %}
	{ action_emergency_stop("ratos_hybrid_corexy NOT INVERTED! Inverted hybrid core-xy bugfix not detected.") }
	{% endif %}

[gcode_macro RATOS_ECHO]
gcode = 
	{% set prefix = "RatOS" %}
	{% set debug = params.DEBUG|default(0)|int %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " | " ~ params.PREFIX %}
	{% endif %}
	{% set prefix = prefix ~ ":" %}
	{% set msg = "" %}
	{% if params.MSG is defined %}
	{% set msg = params.MSG %}
	{% else %}
	{% set msg = "No msg parameter provided (this is a bug or unintended use)." %}
	{% endif %}
	{% if not debug %}
	
	M117 {prefix} {msg}
	{% endif %}
	RATOS_LOG PREFIX="{prefix}" MSG="{msg}"
	{% if not debug %}
	RESPOND PREFIX="{prefix}" MSG="{msg}"
	{% else %}
	CONSOLE_ECHO TITLE="{prefix}" TYPE="debug" MSG="{msg}"
	{% endif %}

[gcode_macro ENABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=True
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=prefix_filter VALUE="'{params.FILTER|default('')|lower}'"
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging enabled."

[gcode_macro DISABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=False
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging disabled."

[gcode_macro DEBUG_ECHO]
variable_enabled = False
variable_prefix_filter = ''
gcode = 
	{% set prefix = "DEBUG" %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " - " ~ params.PREFIX %}
	{% endif %}
	{% if enabled and (prefix_filter|lower == '' or prefix_filter|lower in params.PREFIX|lower) %}
	RATOS_ECHO PREFIX="{prefix}" MSG="{params.MSG}" DEBUG=1
	{% endif %}

[gcode_macro START_FEATURE]
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="Start {params.FEATURE} feature gcode"
	{% set scv = printer.toolhead.square_corner_velocity|int|default(5) %}
	{% set accel = printer.toolhead.max_accel|int|default(10000) %}
	{% set ratio = printer.toolhead.minimum_cruise_ratio|float|default(0.5) %}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="scv" VALUE={scv}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="accel" VALUE={accel}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="ratio" VALUE={ratio}
	_USER_START_FEATURE FEATURE="{params.FEATURE}"

[gcode_macro END_FEATURE]
variable_scv = 5
variable_accel = 10000
variable_ratio = 0.5
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="End {params.FEATURE} feature gcode"
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={scv} ACCEL={accel} MINIMUM_CRUISE_RATIO={ratio}
	_USER_END_FEATURE FEATURE="{params.FEATURE}" SCV={scv} ACCEL={accel} RATIO={ratio}

[gcode_macro _ON_LAYER_CHANGE]
variable_layer_number = 0
description = INTERNAL USE ONLY. Call it from the slicers after layer change custom gcode
gcode = 
	
	{% set layer = params.LAYER|int %}
	
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE={layer}
	SET_PRINT_STATS_INFO CURRENT_LAYER={layer}

[gcode_macro _LEARN_MORE_CALIBRATION]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/calibration" %}
	{% set link_text = "RatOS Calibration Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_CHAMBER_FILTER]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter Control" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_FILAMENT]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/filaments" %}
	{% set link_text = "RatOS Filament Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _CONSOLE_SAVE_CONFIG]
gcode = 
	M118 Click <a class="command text--blue">SAVE_CONFIG</a> to save the settings to your printer.cfg.

[gcode_macro _LOAD_RATOS_SKEW_PROFILE]
gcode = 
	{% set ratos_skew_profile = printer["gcode_macro RatOS"].skew_profile|default("") %}
	{% if ratos_skew_profile != "" %}
	{% if printer.fastconfig.config["skew_correction %s" % ratos_skew_profile] is defined %}
	SKEW_PROFILE LOAD={ratos_skew_profile}
	GET_CURRENT_SKEW
	{% else %}
	{% set line_1 = '"Could not find skew profile %s!_N_Clearing skew correction."' % ratos_skew_profile %}
	CONSOLE_ECHO TITLE="Missing skew profile!" TYPE="warning" MSG={line_1}
	SET_SKEW CLEAR=1
	{% endif %}
	{% endif %}

[gcode_macro M601]
gcode = 
	PAUSE

[gcode_macro _STOP_AND_RAISE_ERROR]
gcode = 
	M84
	_RAISE_ERROR MSG="{params.MSG}"

[gcode_macro _RESET_GCODE_VARIABLES]
description = Reset specified [gcode_macro ...] variables to their original values from configuration when Klipper started.
	- MACRO: Name of the GCODE macro containing the variables to reset.
	- VARIABLES: Comma-separated list of variable names to reset (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- QUIET: (optional) If true, suppresses console echo messages for each reset variable. Default is false.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set quiet = params.QUIET|default("false")|lower in ("true", "1", "yes") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	{% set settings = printer.fastconfig.settings[obj_name|lower] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro %s]" % macro) }
	{% endif %}
	
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if settings["variable_%s" % var] is not defined %}
	{ action_raise_error("Variable '%s' is not defined in settings for [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	
	{% for var in vars %}
	{% set var_value = obj[var] %}
	{% if var_value is defined %}
	{% set v = settings["variable_%s" % var] %}
	{% if v != var_value|string %}
	{% if var_value is string %}
	{% set v = '"\'' ~ v|replace('"', '\\"')|replace("'", "\\'") ~ '\'"' %}
	{% endif %}
	SET_GCODE_VARIABLE MACRO={macro} VARIABLE={var} VALUE={v}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Reset {macro} variable {var} to original value: {v} (was {obj[var]})"
	{% endif %}
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro _SHOW_GCODE_VARIABLES]
description = Show current values of specified [gcode_macro ...] variables.
	- MACRO: Name of the GCODE macro containing the variables to show.
	- VARIABLES: Comma-separated list of variable names to show (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- PAD: (optional) If defined, provide a single character to use for padding variable names to align values in a tabular format in the console output. Default is no padding.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set pad = params.PAD|default("") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	
	{% set ns = namespace() %}
	{% set ns.max_len = 0 %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% set ns.max_len = (ns.max_len, var|length)|max %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if pad %}
	{% set padding = pad * (ns.max_len - var|length) %}
	CONSOLE_ECHO MSG="{var}{padding} {obj[var]}"
	{% else %}
	CONSOLE_ECHO MSG="{var}: {obj[var]}"
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro PAUSE]
description = Pauses the print
rename_existing = PAUSE_BASE
variable_extrude = 1.5
variable_retract = 1.5
variable_fan_speed = 0
variable_idex_mode = ""
variable_idex_toolhead = 0
variable_idex_toolhead_x = 0.0
variable_idex_toolhead_y = 0.0
variable_idex_toolhead_z = 0.0
gcode = 
	RATOS_ECHO MSG="Pausing print..."
	
	
	{% set runout_detected = true if params.RUNOUT|default(false)|lower == 'true' else false %}
	
	
	_LED_PAUSE
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	SAVE_GCODE_STATE NAME=PAUSE_state
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_mode VALUE='"{idex_mode}"'
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={idex_toolhead}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_x VALUE={printer.gcode_move.gcode_position.x|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_y VALUE={printer.gcode_move.gcode_position.y|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_z VALUE={printer.gcode_move.gcode_position.z|float}
	DEBUG_ECHO PREFIX="PAUSE" MSG="idex_mode: {idex_mode}, idex_toolhead: {idex_toolhead}, idex_toolhead_x: {idex_toolhead_x}, idex_toolhead_y: {idex_toolhead_y}, idex_toolhead_z: {idex_toolhead_z}"
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="pause"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if current_z < (max_z - 20.0) %}
	{% set z_safe = 20.0 %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	PAUSE_BASE
	
	
	{% if printer["dual_carriage"] is not defined %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan"].speed|float}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	{% if idex_toolhead == 0 %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t1"].speed|float}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106 S0
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set R = printer["gcode_macro PAUSE"].retract|float %}
	{% if can_extrude %}
	G91
	G1 E-{R} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	{% set pause_print_park_x = printer["gcode_macro RatOS"].pause_print_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].pause_print_park_in %}
	{% if runout_detected %}
	{% set pause_print_park_x = printer["gcode_macro RatOS"].runout_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].runout_park_in %}
	{% endif %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	DEBUG_ECHO PREFIX="PAUSE" MSG="z_speed: {z_speed}, pause_print_park_x: {pause_print_park_x}, pause_print_park_in: {pause_print_park_in}, default_toolhead: {default_toolhead}"
	{% if "xyz" in printer.toolhead.homed_axes %}
	G91
	G1 Z{z_safe} F{z_speed}
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% else %}
	
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	_IDEX_SINGLE X={parking_position}
	{% else %}
	PARK_TOOLHEAD
	{% endif %}
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="pause"
	
	RATOS_ECHO MSG="Print paused"

[gcode_macro RESUME]
description = Resumes the print if the printer is paused.
rename_existing = RESUME_BASE
gcode = 
	
	
	RATOS_ECHO MSG="Resuming print..."
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	
	{% set target_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set target_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if target_idex_mode != '' %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set fan_speed = printer["gcode_macro PAUSE"].fan_speed|float %}
	{% if printer["dual_carriage"] is not defined %}
	M106 S{(fan_speed * 255)}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% else %}
	{% if params.TOOLHEAD is defined %}
	
	{% if params.TOOLHEAD == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% else %}
	{% if printer["gcode_macro PAUSE"].idex_toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	{% if params.TOOLHEAD is defined %}
	_SELECT_TOOL T={params.TOOLHEAD} X=-1 Y=-1 TOOLSHIFT=false
	{% else %}
	_SELECT_TOOL T={printer["gcode_macro PAUSE"].idex_toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	{% endif %}
	
	{% set x = printer["gcode_macro PAUSE"].idex_toolhead_x|float %}
	{% set y = printer["gcode_macro PAUSE"].idex_toolhead_y|float %}
	{% set z = printer["gcode_macro PAUSE"].idex_toolhead_z|float %}
	G1 X{x} Y{y} Z{z} F{speed}
	{% if params.TOOLHEAD is defined %}
	
	SAVE_GCODE_STATE NAME=PAUSE_STATE
	{% endif %}
	{% endif %}
	
	
	{% if params.TOOLHEAD is not defined %}
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% if can_extrude %}
	G91
	G1 E{E} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1 MOVE_SPEED={speed}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	RESUME_BASE
	
	
	_LED_PRINTING
	
	RATOS_ECHO MSG="Print resumed"

[gcode_macro CANCEL_PRINT]
description = Cancels the print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	RATOS_ECHO MSG="Cancelling print..."
	END_PRINT
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	
	CANCEL_PRINT_BASE
	RATOS_ECHO MSG="Print cancelled"

[gcode_macro START_PRINT]
description = Start print procedure, use this in your Slicer.
variable_post_processor_version = 2
variable_is_printing_gcode = False
variable_both_toolheads = True
variable_object_xoffset = 0
variable_first_x = -1
variable_first_y = -1
variable_total_toolshifts = 0
variable_initial_tool = 0
variable_extruder_first_layer_temp = ""
variable_extruder_other_layer_temp = ""
gcode = 
	
	{% if params.EXTRUDER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_TEMP parameter not found.")}
	{% endif %}
	{% if params.EXTRUDER_OTHER_LAYER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_OTHER_LAYER_TEMP parameter not found.")}
	{% endif %}
	{% if params.BED_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. BED_TEMP parameter not found.")}
	{% endif %}
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' and printer["gcode_macro RatOS"].danger_force_allow_auto_center_subject|default(false)|lower != 'true'%}
	
	
	
	
	
	{ action_raise_error("The experimental auto_center_subject feature is not supported in this version of RatOS. Please disable it in the RatOS macro settings.") }
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes and printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% if printer["gcode_macro _VAOC"].is_started|default(true)|lower == 'true' %}
	_VAOC_END
	{% endif %}
	{% endif %}
	
	
	_LED_START_PRINTING
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_USER_START_PRINT { rawparams }
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_probe_stowable = printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% endif %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	{% set X0 = params.X0|default(-1)|float %}
	{% set X1 = params.X1|default(-1)|float %}
	{% set Y0 = params.Y0|default(-1)|float %}
	{% set Y1 = params.Y1|default(-1)|float %}
	{% if first_x == -1 or first_y == -1 %}
	{% set first_x = params.FIRST_X|default(-1)|float %}
	{% set first_y = params.FIRST_Y|default(-1)|float %}
	{% endif %}
	{% set total_toolshifts = params.TOTAL_TOOLSHIFTS|default(0)|int %}
	{% set initial_tool = params.INITIAL_TOOL|default(default_toolhead)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	
	
	
	
	
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(printer.heater_bed.target, true)|float %}
	
	
	{% set total_layer_count = params.TOTAL_LAYER_COUNT|default(0)|int %}
	{% set extruder_first_layer_temp = (params.EXTRUDER_TEMP|default("")).split(",") %}
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL BEACON_CONTACT_START_PRINT_TRUE_ZERO={beacon_contact_start_print_true_zero} BEACON_CONTACT_CALIBRATE_MODEL_ON_TRUE_ZERO={beacon_contact_calibrate_model_on_true_zero}
	{% endif %}
	
	_START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH BED_TEMP={bed_temp}
	
	
	RATOS_ECHO MSG="First print coordinates X:{first_x} Y:{first_y}"
	
	
	{% if params.TOTAL_LAYER_COUNT is not defined %}
	{% set link_url = "https://os.ratrig.com/docs/slicers" %}
	{% set link_text = "RatOS Slicer Configuration" %}
	{% set line_1 = '"Your slicer gcode settings are not up to date._N_Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="Incomplete Slicer Configuration detected" TYPE="warning" MSG={line_1}
	{% endif %}
	
	
	SET_PRINT_STATS_INFO CURRENT_LAYER=1
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE=1
	{% if total_layer_count > 0 %}
	SET_PRINT_STATS_INFO TOTAL_LAYER={total_layer_count}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads %}
	{% set initial_tool = 0 if initial_tool == 1 else 1 %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	{% endif %}
	
	
	{% set both_toolheads = true %}
	{% if total_toolshifts == 0 %}
	{% set both_toolheads = false %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	{% endif %}
	{% if both_toolheads and (idex_mode == "copy" or idex_mode == "mirror") %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Gcode tool changes found. Copy and mirror mode do not support toolchanges.")}
	{% endif %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set both_toolheads = true %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=initial_tool VALUE={initial_tool}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_x VALUE={first_x}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_y VALUE={first_y}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=total_toolshifts VALUE={total_toolshifts}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=both_toolheads VALUE={both_toolheads}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_first_layer_temp VALUE="'{params.EXTRUDER_TEMP}'"
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_other_layer_temp VALUE="'{params.EXTRUDER_OTHER_LAYER_TEMP}'"
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE=0
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set svv = printer.save_variables.variables %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set stepper_x_position_min = printer.fastconfig.settings.stepper_x.position_min|float %}
	{% set stepper_x_position_endstop = printer.fastconfig.settings.stepper_x.position_endstop|float %}
	{% set dual_carriage_position_max = printer.fastconfig.settings.dual_carriage.position_max|float %}
	{% set dual_carriage_position_endstop = printer.fastconfig.settings.dual_carriage.position_endstop|float %}
	{% set x_parking_space = parking_position_t0 - (stepper_x_position_endstop , stepper_x_position_min)|max %}
	{% set dc_parking_space = (dual_carriage_position_endstop , dual_carriage_position_max)|min - parking_position_t1 %}
	{% if svv.idex_xoffset|abs >= (x_parking_space - 0.5) or svv.idex_xoffset|abs >= (dc_parking_space - 0.5) %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Toolhead x-offset is too high for the available parking space. Calibrate your X and DC endstop positions and make sure you stay below 1mm." % (copy_mode_max_width)) }
	{% endif %}
	{% endif %}
	
	
	{% if (idex_mode == "copy" or idex_mode == "mirror") and printer.fastconfig.settings.ratos.enable_gcode_transform %}
	
	{% if params.MIN_X is not defined or params.MAX_X is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Something went wrong! Missing important post processor start print parameter!") }
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE=0
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	
	{% set boundary_box_min_x = params.MIN_X|default(0)|float %}
	{% set boundary_box_max_x = params.MAX_X|default(printable_x_max)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if default_toolhead == 0 %}
	
	{% set boundary_box_max_x = boundary_box_max_x + svv.idex_xoffset %}
	{% else %}
	
	{% set boundary_box_min_x = boundary_box_min_x - svv.idex_xoffset %}
	{% endif %}
	
	{% set center_x = printable_x_max / 2.0 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set object_width = boundary_box_max_x - boundary_box_min_x %}
	{% set copy_mode_max_width = center_x %}
	{% set mirror_mode_max_width = center_x - safe_distance / 2.0 %}
	
	DEBUG_ECHO PREFIX="START_PRINT" MSG="OBJECT_WIDTH: {object_width} BOUNDARY_BOX_MIN_X: {boundary_box_min_x} BOUNDARY_BOX_MAX_X: {boundary_box_max_x} CENTER_X: {center_x} SAFE_DISTANCE: {safe_distance}"
	
	
	{% if idex_mode == "copy" and object_width > copy_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for copy mode! Max supported width is %s mm" % (copy_mode_max_width)) }
	{% endif %}
	{% if idex_mode == "mirror" and object_width > mirror_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for mirror mode! Max supported width is %s mm" % (mirror_mode_max_width)) }
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = (printable_x_max - boundary_box_max_x - boundary_box_min_x) / 2 %}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE={object_xoffset}
	{% endif %}
	
	{% endif %}
	
	
	{% set has_initial_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_toolhead_filament_sensor %}
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% set has_initial_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_bowden_filament_sensor %}
	
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% if printer["dual_carriage"] is defined and both_toolheads %}
	
	{% set has_secondary_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set has_secondary_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_CHAMBER_FILTER_ON AT="before_print_start"
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true' %}
	{% if both_toolheads %}
	RATOS_ECHO MSG="Spool join is not possible if both toolheads are in use!"
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	{% endif %}
	
	
	CLEAR_PAUSE
	{% if printer["gcode_macro RatOS"].force_absolute_position|lower == 'true' %}
	G90
	{% endif %}
	SAVE_GCODE_STATE NAME=start_print_state
	
	
	G21
	
	G90
	
	M82
	_USER_START_PRINT_BEFORE_HOMING { rawparams }
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_BEGIN_BATCH
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_Z_HOP
	
	
	{% if idex_mode != '' and not (printer.fastconfig.settings.beacon is defined and (beacon_contact_start_print_true_zero or beacon_adaptive_heat_soak)) %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	{% if chamber_temp > 0 %}
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED={printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float}
	{% endif %}
	{% endif %}
	_CHAMBER_HEATER_ON START_CHAMBER_TEMP={start_chamber_temp} CHAMBER_TEMP={chamber_temp}
	_USER_START_PRINT_HEAT_CHAMBER { rawparams } CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_START_PRINT_BEFORE_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	RATOS_ECHO MSG="Heating bed..."
	
	M190 S{bed_temp}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_adaptive_heat_soak %}
	_MOVE_TO_SAFE_Z_HOME
	
	G1 Z2.5 F{z_speed}
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK LAYER_QUALITY={beacon_adaptive_heat_soak_layer_quality} MAXIMUM_FIRST_LAYER_DURATION={beacon_adaptive_heat_soak_maximum_first_layer_duration} MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={beacon_adaptive_heat_soak_max_wait}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_BED { rawparams }
	
	
	_START_PRINT_AFTER_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	_USER_START_PRINT_BED_MESH { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_BED_MESH X0={X0} X1={X1} Y0={Y0} Y1={Y1} T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_END_BATCH
	{% endif %}
	
	
	{% if idex_mode == '' %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[initial_tool]|float}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[0]|float}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={extruder_first_layer_temp[1]|float}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_PARK { rawparams }
	
	
	_START_PRINT_PARK
	
	
	RATOS_ECHO MSG="Heating Extruder..."
	{% if idex_mode == '' %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[initial_tool]|float}  MAXIMUM={extruder_first_layer_temp[initial_tool]|float + 5}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[0]|float}  MAXIMUM={extruder_first_layer_temp[0]|float + 5}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder1" MINIMUM={extruder_first_layer_temp[1]|float}  MAXIMUM={extruder_first_layer_temp[1]|float + 5}
	{% endif %}
	{% endif %}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	{% if idex_mode == '' %}
	_LED_PRINTING
	{% else %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	_LED_PRINTING
	{% else %}
	{% if both_toolheads %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	{% if toolchange_standby_temp > -1 %}
	_LED_TOOLHEAD_STANDBY TOOLHEAD={0 if initial_tool == 1 else 1}
	{% else %}
	_LED_PRINTING TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% else %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_EXTRUDER { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_AFTER_HEATING_EXTRUDER X0={X0} X1={X1} Y0={Y0} Y1={Y1} INITIAL_TOOLHEAD={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if idex_mode != '' %}
	{% if not both_toolheads %}
	{% if initial_tool != default_toolhead %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if idex_mode != '' %}
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=standby VALUE=False
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=standby VALUE=False
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if initial_tool == 1 else 'extruder1'} TARGET={toolchange_standby_temp}
	SET_GCODE_VARIABLE MACRO=T{0 if initial_tool == 1 else 1} VARIABLE=standby VALUE=True
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=start_print_state
	
	{% if printer["dual_carriage"] is defined %}
	_SET_IDEX_MODE_OFFSET
	{% endif %}
	
	
	{% if idex_mode != '' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% if idex_mode == "copy" and idex_mode != act_idex_mode %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == "mirror" and idex_mode != act_idex_mode %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={object_xoffset} MOVE=0
	{% endif %}
	{% else %}
	_SELECT_TOOL T={initial_tool} TOOLSHIFT=false
	_SET_TOOLHEAD_OFFSET
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	_SET_EXTRUSION_MODE
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={printer["print_stats"].print_duration}
	{% endif %}
	
	
	_USER_END_START_PRINT { rawparams }
	
	G92 E0
	
	
	_CHAMBER_FILTER_ON AT="after_print_start"
	
	_ALERT_NON_ZERO_Z_OFFSET
	
	RATOS_ECHO MSG="Printing..."

[gcode_macro _START_PRINT_BEFORE_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set is_stowable_probe = true if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' else false %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Pre-heating extruder..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={min_temp}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET={min_temp}
	{% endif %}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	{% endif %}
	{% endif %}
	
	
	{% if not is_stowable_probe %}
	{% if printer["dual_carriage"] is defined and act_t != default_toolhead %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	{% endif %}
	RATOS_ECHO MSG="Heat soaking z probe..."
	_MOVE_TO_SAFE_Z_HOME
	
	G0 Z2 F{z_speed}
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Waiting for extruder to be preheated..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	{% if default_toolhead == 0 %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_Z_HOP
	{% endif %}
	
	
	{% if auto_z_offset_calibration %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	PARK_TOOLHEAD
	_CLEANING_MOVE TOOLHEAD={default_toolhead} AUTOMATED=True
	_SELECT_TOOL T={0 if default_toolhead == 1 else 1} X={parking_position_t0 if default_toolhead == 1 else parking_position_t1} Y=0 TOOLSHIFT=false
	_CLEANING_MOVE TOOLHEAD={0 if default_toolhead == 1 else 1} AUTOMATED=True
	_VAOC_CALIBRATE_Z_OFFSET AUTO_Z_OFFSET=True
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=false
	{% endif %}
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	{% if needs_rehoming %}
	G28 Z
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	_START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE
	{% endif %}
	{% endif %}
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	PROBE PROBE_METHOD=contact SAMPLES=1

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	{% set fuzzy_radius = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_radius|default(0)|float if beacon_contact_start_print_true_zero_fuzzy_position else 0 %}
	
	{% set contact_true_zero_temp_has_been_set = False %}
	
	
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	
	
	
	{% if printer.beacon.last_probe_result|lower == "ok" %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	RATOS_ECHO MSG="Auto calibration nozzle wipe with probe result {last_z_offset}..."
	G0 Z{(0.2 + last_z_offset)} F{z_speed}
	G0 X70 F300
	{% else %}
	RATOS_ECHO MSG="Skipping auto calibration nozzle wipe because probing failed!"
	{% endif %}
	{% elif beacon_contact_wipe_before_true_zero_method == "probe_clean" %}
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	
	{% set contact_true_zero_temp_has_been_set = True %}
	
	
	
	
	
	
	
	
	BEACON_PROBE_CLEAN X=50 Y=10
	{% else %}
	CONSOLE_ECHO TYPE="error" TITLE="Unknown wipe method" MSG="Unknown wipe method '{beacon_contact_wipe_before_true_zero_method}' configured, skipping wipe before beacon true zero."
	{% endif %}
	{% endif %}
	
	
	G0 Z5 F{z_speed}
	_MOVE_TO_SAFE_Z_HOME FUZZY_RADIUS={fuzzy_radius}
	
	
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION
	
	{% if not contact_true_zero_temp_has_been_set %}
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon contact auto calibration..."
	
	{% if beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	
	G0 Z5 F{z_speed}

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION]
gcode = 
	{% set pos = printer.ratos.last_move_to_safe_z_home_position %}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE={pos[0]}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE={pos[1]}

[gcode_macro _START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set first_x = printer["gcode_macro START_PRINT"].first_x|default(-1)|float %}
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2.0 %}
	{% set center_y = printable_y_max / 2.0 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% if printer["dual_carriage"] is defined %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% endif %}
	
	
	{% set X0 = params.X0|default(-1)|int %}
	{% set X1 = params.X1|default(-1)|int %}
	{% set Y0 = params.Y0|default(-1)|int %}
	{% set Y1 = params.Y1|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	
	{% if idex_mode == '' %}
	
	_PRIME
	{% else %}
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	RATOS_ECHO PREFIX="IDEX" MSG="using combined prime offset for IDEX {idex_mode} mode"
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	{% if both_toolheads %}
	{% if initial_toolhead == 0 %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T{initial_toolhead}"
	_SELECT_TOOL T={initial_toolhead} TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	SET_MACRO_TRAVEL_SETTINGS
	
	{% if (X0 > -1 and Y1 > -1) or (first_x > 0 and first_y > 0) %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	{% endif %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	{% set first_z = 1 %}
	{% else %}
	{% set first_z = 3 %}
	{% endif %}
	
	
	{% if idex_mode == "mirror" %}
	{% if first_y >= 0 %}
	G0 Y{first_y} F{speed}
	{% else %}
	G0 Y{Y1} F{speed}
	{% endif %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={initial_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={initial_toolhead} E={printer["gcode_macro RatOS"].toolchange_first_purge|default(50)|float}
	_CLEANING_MOVE TOOLHEAD={initial_toolhead} AUTOMATED=True
	{% endif %}
	{% if first_x >= 0 and first_y >= 0 %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% else %}
	{% set first_x = X0 %}
	{% set first_y = Y0 %}
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'min' %}
	{% set first_x = X0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'max' %}
	{% set first_x = X1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|float <= center_x %}
	{% set first_x = X0 %}
	{% else %}
	{% set first_x = X1 %}
	{% endif %}
	{% endif %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'min' %}
	{% set first_y = Y0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'max' %}
	{% set first_y = Y1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|float <= center_y %}
	{% set first_y = Y0 %}
	{% else %}
	{% set first_y = Y1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	
	
	_LOAD_RATOS_SKEW_PROFILE

[gcode_macro _PRIME]
gcode = 
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	PRIME_BLOB INITIAL_TOOLHEAD={params.INITIAL_TOOLHEAD} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={params.IDEX_MODE} Y1={params.Y1}
	{% else %}
	
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif params.IDEX_MODE == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro END_PRINT]
description = End print procedure, use this in your Slicer.
gcode = 
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SAVE_GCODE_STATE NAME=end_print_state
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = printer["gcode_macro START_PRINT"].object_xoffset|default(0)|float %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(0-object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={(0-object_xoffset)}
	{% endif %}
	{% endif %}
	
	
	_USER_END_PRINT_BEFORE_HEATERS_OFF { rawparams }
	_END_PRINT_BEFORE_HEATERS_OFF
	TURN_OFF_HEATERS
	_USER_END_PRINT_AFTER_HEATERS_OFF { rawparams }
	_END_PRINT_AFTER_HEATERS_OFF
	_USER_END_PRINT_PARK { rawparams }
	_END_PRINT_PARK
	
	
	{% if printer["gcode_macro RatOS"].skew_profile is defined %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined and printer["gcode_macro RatOS"].end_print_motors_off|lower != 'false' %}
	
	M84
	{% endif %}
	
	
	M107
	
	
	BED_MESH_CLEAR
	RATOS_ECHO MSG="Done :)"
	
	
	RESTORE_GCODE_STATE NAME=end_print_state
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	M84
	{% endif %}
	
	
	RESET_NAMED_OFFSET EVENT="end_print"
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_CHAMBER_FILTER_ON AT="print_end"
	_CHAMBER_FILTER_OFF
	
	
	_CHAMBER_HEATER_OFF
	
	_USER_END_PRINT_FINISHED { rawparams }

[gcode_macro _END_PRINT_BEFORE_HEATERS_OFF]
gcode = 
	RATOS_ECHO MSG="Cleaning up..."

[gcode_macro _END_PRINT_AFTER_HEATERS_OFF]
gcode = 
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% set z_hop = printer["gcode_macro RatOS"].end_print_park_z_hop|float %}
	{% set r = printer["gcode_macro RatOS"].end_print_retract_filament|default(4)|float %}
	{% if current_z < (max_z - z_hop) %}
	{% set z_safe = z_hop %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G91
	
	{% if can_extrude %}
	G1 E-2 F3600
	{% endif %}
	
	G0 Z{z_safe} F3600
	
	{% if can_extrude %}
	G1 E-{(r-2)} F3600
	{% endif %}
	
	G90

[gcode_macro _SET_EXTRUSION_MODE]
gcode = 
	
	{% if printer["gcode_macro RatOS"].relative_extrusion|lower == 'true' %}
	M83
	{% else %}
	M82
	{% endif %}

[gcode_macro GENERATE_SHAPER_GRAPHS]
description = Genarates input shaper resonances graphs for analysis. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	{% set hz_per_sec = params.HZ_PER_SEC|default(1)|float %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set copy_mode_offset = printable_x_max / 4.0 %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	_IDEX_SINGLE
	{% endif %}
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	
	
	{% if idex_mode != 'copy' and idex_mode != 'mirror' %}
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	{% endif %}
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Shaper graph"

[gcode_shell_command generate_shaper_graph_x]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-x.sh
timeout = 60.
verbose = True

[gcode_shell_command generate_shaper_graph_y]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-y.sh
timeout = 60.
verbose = True

[gcode_macro MEASURE_COREXY_BELT_TENSION]
description = Generates resonance graph used to ensure belts are equally tensioned. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	_IDEX_SINGLE
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if measure_t1 == false or measure_t0 == false %}
	{action_raise_error("Axis specified. Not supported for belt tension on Y.")}
	{% else %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	G4 P5000
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	PARK_TOOLHEAD
	{% endif %}
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	G1 X{parking_position_t1} F{speed}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	
	
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Belt Tension Graph"

[gcode_shell_command generate_belt_tension_graph]
command = /home/pi/printer_data/config/RatOS/scripts/generate-belt-tension-graph.sh
timeout = 90.
verbose = True

[idle_timeout]
gcode = 
	{% if printer.webhooks.state|lower == 'ready' %}
	{% if printer.pause_resume.is_paused|lower == 'false' %}
	_USER_BEFORE_IDLE_TIMEOUT
	RATOS_ECHO PREFIX="IDLE" MSG="2 hours since last activity. Powering off heaters and motors.."
	TURN_OFF_HEATERS
	M84
	_USER_AFTER_IDLE_TIMEOUT
	{% endif %}
	{% endif %}
timeout = 7200

[temperature_sensor raspberry_pi]
sensor_type = temperature_host

[skew_correction]

[named_offsets]

[input_shaper]

[virtual_sdcard]
path = ~/printer_data/gcodes

[display_status]

[pause_resume]

[force_move]
enable_force_move = True

[respond]

[resonance_generator]

[ratos]
allow_unknown_gcode_generator = True
enable_gcode_transform = True

[exclude_object]

[bed_mesh]
split_delta_z = 0.001
horizontal_move_z = 2
mesh_min = 20,20
mesh_max = 480,480
probe_count = 40,40
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = .2
speed = 600
log_points = False

[fastconfig]

[heater_bed]
heater_pin = heater_bed_heating_pin
sensor_pin = heater_bed_sensor_pin
sensor_type = Generic 3950
min_temp = 0
max_temp = 140
pwm_cycle_time = 0.103
control = pid
pid_kp = 61.987
pid_ki = 1.781
pid_kd = 539.289

[printer]
kinematics = ratos_hybrid_corexy
max_velocity = 800
max_accel = 10000
minimum_cruise_ratio = 0.5
max_z_velocity = 50
max_z_accel = 600
square_corner_velocity = 5

[ratos_hybrid_corexy]
inverted = true

[dual_carriage]
axis = x
safe_distance = 55
position_max = 559.6
position_endstop = 559.6
position_min = 0
step_pin = PF9
dir_pin = dual_carriage_dir_pin
enable_pin = !PG2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t1:PA2

[gcode_macro _SET_IDEX_MODE_OFFSET]
description = "Internal use only. Sets the 'idex_mode' named offset that the active idex mode requires."
gcode = 
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_SET_IDEX_MODE_OFFSET" MSG="idex_mode: {idex_mode}, center_x: {center_x}"
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	SET_NAMED_OFFSET NAME=idex_mode X={(-center_x / 2)}
	{% else %}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% else %}
	{action_raise_error("_SET_IDEX_MODE_OFFSET: Printer not homed")}
	{% endif %}

[gcode_macro IDEX_SINGLE]
gcode = 
	_IDEX_REMAP_TOOLHEADS ENABLE=False
	_IDEX_SINGLE

[gcode_macro _IDEX_SINGLE]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_single"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set init = params.INIT|default(0)|int %}
	{% set new_x = params.X|default(-1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_default_t = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="init: {init}, new_x: {new_x}, idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, act_t: {act_t}"
	
	{% if idex_mode == "copy" or idex_mode == "mirror" or init == 1 %}
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="reset idex_mode offset"
	G1 X{center_x} F{(speed)}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="activate default carriage"
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolheads"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	G90
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position."
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1}
	G1 X{parking_position_default_t} F{speed}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move default toolhead to its new position."
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% if new_x == -1 %}
	{% set new_x = center_x %}
	{% endif %}
	G1 X{new_x} F{speed}
	
	M400
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="X Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set extruder motion queue."
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if default_toolhead==0 else default_toolhead}
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolhead offset."
	_SET_TOOLHEAD_OFFSET
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set input shaper."
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[default_toolhead]|float)} SHAPER_FREQ_Y={(shaper_y_freq[default_toolhead]|float)} SHAPER_TYPE_X={(shaper_x_type[default_toolhead]|lower)} SHAPER_TYPE_Y={(shaper_y_type[default_toolhead]|lower)}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="update Frontend."
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if default_toolhead==0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if default_toolhead==1 else False}
	{% else %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_single"

[gcode_macro IDEX_COPY]
gcode = 
	_IDEX_COPY

[gcode_macro _IDEX_COPY]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_copy"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set y = params.Y|default(-1)|int %}
	{% set dance = params.DANCE|default(1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_COPY" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}, y: {y}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "copy" %}
	{% if idex_mode == "mirror" %}
	{% if y>=0 %}
	G1 X{center_x} Y{y} F{(speed)}
	{% else %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	
	
	{% if idex_mode != "mirror" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance == 1 %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[2]|float)} SHAPER_FREQ_Y={(shaper_y_freq[2]|float)} SHAPER_TYPE_X={(shaper_x_type[2]|lower)} SHAPER_TYPE_Y={(shaper_y_type[2]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_copy"

[gcode_macro IDEX_MIRROR]
gcode = 
	_IDEX_MIRROR

[gcode_macro _IDEX_MIRROR]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_mirror"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set dance = params.DANCE|default(1)|int %}
	{% set priming = params.PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_MIRROR" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "mirror" %}
	
	{% if idex_mode == "copy" %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS MIRROR_PRIMING={params.PRIMING}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=MIRROR
	
	
	{% if idex_mode != "copy" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance and not priming %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[3]|float)} SHAPER_FREQ_Y={(shaper_y_freq[3]|float)} SHAPER_TYPE_X={(shaper_x_type[3]|lower)} SHAPER_TYPE_Y={(shaper_y_type[3]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_mirror"

[gcode_macro _IDEX_SET_TOOLHEADS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set mirror_priming = params.MIRROR_PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position_inactive_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_IDEX_SET_TOOLHEADS" MSG="idex_mode: {idex_mode}, act_t: {act_t}, center_x: {center_x}, mirror_priming: {mirror_priming}"
	
	
	{% if act_t != default_toolhead %}
	_SET_TOOLHEAD_OFFSET FORCE_TOOLHEAD={default_toolhead} MOVE=1
	{% endif %}
	
	{% if mirror_priming %}
	
	
	
	{% if parking_position_t0|abs < parking_position_t1 - printable_x_max %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{printable_x_max + parking_position_t0|abs} F{(speed)}
	{% else %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{0 - (parking_position_t1 - printable_x_max)} F{(speed)}
	{% endif %}
	
	{% else %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1} MODE=PRIMARY
	G1 X{parking_position_inactive_t} F{(speed)}
	
	
	{% if act_t==1 %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{center_x / 2} F{(speed)}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"

[gcode_macro IDEX_PARK]
gcode = 
	
	PARK_TOOLHEAD

[gcode_macro PARK_TOOLHEAD]
gcode = 
	
	{% set idex_mode = 'none' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="PARK_TOOLHEAD" MSG="Parking T{act_t}.."
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set parking_position_inact_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set printable_y_min = printer["gcode_macro RatOS"].printable_y_min|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" and 'xy' in printer.toolhead.homed_axes %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% elif printer.toolhead.position.y|float < printable_y_min %}
	G1 Y{printable_y_min} F{speed}
	{% endif %}
	
	SAVE_GCODE_STATE NAME=_PARK_TOOLHEAD
	G90
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0.5
	
	
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_inact_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	
	SET_VELOCITY_LIMIT ACCEL={printer.toolhead.max_accel} MINIMUM_CRUISE_RATIO=0.5
	M400
	RESTORE_GCODE_STATE NAME=_PARK_TOOLHEAD
	
	{% endif %}

[gcode_macro JOIN_SPOOLS]
gcode = 
	
	{% set spools = params.SPOOLS|default("") %}
	
	{% if spools == "" %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% else %}
	{% if spools != "0,1" and spools != "1,0" %}
	RATOS_ECHO MSG="Wrong spool configuration!"
	RATOS_ECHO MSG="Join Spools = JOIN_SPOOLS SPOOLS=0,1"
	RATOS_ECHO MSG="Deactivate = JOIN_SPOOLS SPOOLS="
	{% else %}
	{% if spools == "0,1" or spools == "1,0" %}
	_IDEX_JOIN_SPOOLS ENABLE=true
	{% else %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_JOIN_SPOOLS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if enable %}
	{% set has_t0_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t1_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t0_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined else false %}
	{% set has_t1_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined else false %}
	{% if (has_t0_toolhead_filament_sensor and has_t1_toolhead_filament_sensor) or (has_t0_bowden_filament_sensor and has_t1_bowden_filament_sensor) %}
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=True
	RATOS_ECHO MSG="Spool joining enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Can not enable spool joining! No filament sensors found."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining deactivated!"
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining is not possible in copy and mirror mode!"
	{% endif %}

[gcode_macro _JOIN_SPOOL]
gcode = 
	
	{% set old_toolhead = params.TOOLHEAD|int %}
	{% set new_toolhead = 0 if old_toolhead == 1 else 1 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set purge_after_load = printer["gcode_macro T%s" % new_toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_JOIN_SPOOL" MSG="toolhead: {new_toolhead}"
	
	{% set has_filament = true %}
	{% set has_new_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% set has_new_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% if has_new_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	{% if has_new_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	
	{% if has_filament %}
	RATOS_ECHO MSG="Joining spools! Please wait for extruder to heat up...."
	
	
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={new_toolhead}
	
	
	_DEACTIVATE_TOOLHEAD TOOLHEAD={old_toolhead}
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set extruder_temp = extruder_first_layer_temp[new_toolhead]|float %}
	{% else %}
	{% set extruder_temp = extruder_other_layer_temp[new_toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if new_toolhead == 0 else 'extruder1'} TARGET={extruder_temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if new_toolhead == 0 else 'extruder1'} MINIMUM={extruder_temp}  MAXIMUM={extruder_temp + 5}
	
	
	{% if purge_after_load > 0 %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_toolhead == 0 else new_toolhead}
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={new_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={new_toolhead} E={purge_after_load}
	_CLEANING_MOVE TOOLHEAD={new_toolhead} AUTOMATED=True
	
	
	SET_DUAL_CARRIAGE CARRIAGE={old_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if old_toolhead == 0 else old_toolhead}
	
	{% endif %}
	
	
	RESUME TOOLHEAD={new_toolhead}
	
	
	_IDEX_JOIN_SPOOLS ENABLE=false
	
	{% else %}
	{ action_raise_error("Spool join failed! No filament found or filament sensor is disabled.") }
	{% endif %}

[gcode_macro REMAP_TOOLHEADS]
gcode = 
	
	{% set toolheads = params.TOOLHEADS|default("") %}
	
	{% if toolheads == "" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% else %}
	{% if toolheads != "0,1" and toolheads != "1,0" %}
	RATOS_ECHO MSG="Wrong toolhead configuration!"
	RATOS_ECHO MSG="Remap = REMAP_TOOLHEADS TOOLHEADS=0,1"
	RATOS_ECHO MSG="Deactivate = REMAP_TOOLHEADS TOOLHEADS="
	{% else %}
	{% if toolheads == "0,1" or toolheads == "1,0" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=true
	_IDEX_SINGLE
	{% else %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_REMAP_TOOLHEADS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	{% if not enable or (idex_mode != "copy" and idex_mode != "mirror") %}
	{% if enable %}
	RATOS_ECHO MSG="Toolhead remapping enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping deactivated!"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE={enable}
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping not possible in copy and mirror mode!"
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	{% endif %}

[gcode_macro SHAPER_CALIBRATE]
rename_existing = SHAPER_CALIBRATE_ORG
gcode = 
	RATOS_ECHO PREFIX="IDEX" MSG="SHAPER_CALIBRATE is useless on IDEX machines. Please use the GENERATE_SHAPER_GRAPHS macro and type the values into `variable_shaper_*_freq` and `variable_shaper_*_type manually`."

[gcode_shell_command generate_shaper_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-shaper-graph.sh
timeout = 120.
verbose = True

[gcode_shell_command generate_tension_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-belt-tension-graph.sh
timeout = 120.
verbose = True

[gcode_macro SET_PRESSURE_ADVANCE]
variable_snyc_toolheads = False
rename_existing = SET_PRESSURE_ADVANCE_BASE
gcode = 
	{% if params.SYNC_TOOLHEADS is defined %}
	{% set snyc_toolheads = true if params.SYNC_TOOLHEADS|default(false)|lower == 'true' else false %}
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=True
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="Syncing toolheads..."
	{% else %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' or snyc_toolheads %}
	{% set advance = params.ADVANCE|default(printer['extruder'].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['extruder'].smooth_time|float)|float %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T0"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T1"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder1' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% else %}
	{% set extruder = 'extruder' if act_t == 0 else 'extruder1' %}
	{% if params.EXTRUDER is defined %}
	{% set extruder = params.EXTRUDER %}
	{% endif %}
	{% if extruder == 'extruder' or extruder == 'extruder1' %}
	{% set advance = params.ADVANCE|default(printer['%s' % extruder].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['%s' % extruder].smooth_time|float)|float %}
	SET_PRESSURE_ADVANCE_BASE EXTRUDER={extruder} ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% if params.EXTRUDER is not defined %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG={"T%s" % act_t}
	{% endif %}
	{% else %}
	SET_PRESSURE_ADVANCE_BASE { rawparams }
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro M106]
rename_existing = M106.1
variable_swap_speed = -1
gcode = 
	
	{% set s = [[params.S|default(255)|int, 255]|min, 0]|max %}
	{% set p = params.P|default(-1)|int %}
	{% set speed = s / 255 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set t = 1 if idex_mode=='primary' else 0 %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(0)|int == 1 else false %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set sync_fans = true %}
	{% endif %}
	
	
	{% if sync_fans and idex_mode != "copy" and idex_mode != "mirror" %}
	
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int %}
	
	
	{% if toolshift_count > total_toolshifts %}
	{% set sync_fans = false %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE=-1
	
	
	{% if p == -1 %}
	
	{% if speed == 0 %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed}
	{% else %}
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE={speed}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={(speed if (t == 0 or sync_fans) else 0)}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={(speed if (t == 1 or sync_fans) else 0)}
	{% endif %}
	{% else %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed if t == p else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed if t == p else 0}
	{% endif %}
	
	
	M106.1 S{s}

[gcode_macro M107]
rename_existing = M107.1
gcode = 
	{% set p = params.P|default(-1)|int %}
	M106 S0 P{p}

[gcode_macro _SELECT_TOOL]
variable_last_timestamp = 0
gcode = 
	{% if params.T is defined %}
	{% set idex_mode = '' %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if "xyz" not in printer.toolhead.homed_axes and (idex_mode == "copy" or idex_mode == "mirror") %}
	_IDEX_SINGLE
	{% set idex_mode = 'reset' %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set new_t = params.T|int %}
	
	
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads and is_printing_gcode %}
	{% set new_t = 0 if new_t == 1 else 1 %}
	{% endif %}
	
	
	{% set toolchange_prepurging_timer = printer["gcode_macro RatOS"].toolchange_prepurging_timer|default(0)|int %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	DEBUG_ECHO PREFIX="_SELECT_TOOL" MSG="act_t: {act_t}, new_t: {new_t}, is_printing_gcode: {is_printing_gcode}, swap_toolheads: {swap_toolheads}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	{% set act_extruder = 'extruder%s' % ('' if new_t == 0 else new_t) %}
	{% if new_t != act_t or printer.toolhead.extruder != act_extruder or idex_mode == 'reset' %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Selecting T{new_t}.."
	
	
	M220 S100
	
	
	
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(1)|int == 1 else false %}
	
	
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set toolshift = false %}
	{% endif %}
	
	
	{% set fan_speed = printer["fan_generic part_fan_t%s" % act_t].speed %}
	
	
	{% set deactivate_toolhead = false %}
	{% if is_printing_gcode %}
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int + 1 %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE={toolshift_count}
	{% if toolshift_count == total_toolshifts %}
	{% set deactivate_toolhead = true %}
	{% endif %}
	{% endif %}
	
	
	{% set needs_wakeup = true if printer["gcode_macro T%s" % new_t].standby|default(false)|lower == 'true' else false %}
	
	
	{% set needs_purging = false %}
	{% set wake_up_purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% if is_printing_gcode and toolchange_prepurging_timer > 0 and wake_up_purge > 0 %}
	{% set new_timestamp = printer["print_stats"].print_duration %}
	{% set elapsed_time = new_timestamp - last_timestamp %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={new_timestamp}
	{% if elapsed_time > toolchange_prepurging_timer %}
	{% set needs_purging = true %}
	{% endif %}
	{% endif %}
	
	
	{% set first_use_purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% if toolshift_count == 1 and first_use_purge > 0 %}
	{% set needs_purging = true %}
	{% endif %}
	
	
	{% if is_printing_gcode and (toolchange_standby_temp > -1 or needs_purging or needs_wakeup) %}
	_TOOLHEAD_STANDBY TOOLHEAD={act_t}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	_TOOLHEAD_WAKEUP TOOLHEAD={new_t} X={new_x} Y={new_y} Z={new_z} FAN_SPEED={fan_speed} TOOLSHIFT_COUNT={toolshift_count}
	{% else %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(false)|lower == 'true' else false %}
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if (new_t == 0 or sync_fans) else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if (new_t == 1 or sync_fans) else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	_TOOLCHANGE T={new_t} X={new_x} Y={new_y} Z={new_z} PARK_T0={park_t0} PARK_T1={park_t1} TOOLSHIFT={toolshift}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[new_t]|float)} SHAPER_FREQ_Y={(shaper_y_freq[new_t]|float)} SHAPER_TYPE_X={(shaper_x_type[new_t]|lower)} SHAPER_TYPE_Y={(shaper_y_type[new_t]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if new_t == 0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if new_t == 1 else False}
	
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% set sanity_check_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if new_t == 0 %}
	{% if printer.toolhead.extruder == 'extruder' %}
	{% if sanity_check_idex_mode == 'primary' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% elif new_t == 1 %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% if sanity_check_idex_mode == 'inactive' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _TOOLHEAD_STANDBY]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Putting toolhead T{toolhead} into standby mode."
	DEBUG_ECHO PREFIX="_TOOLHEAD_STANDBY" MSG="toolhead: {toolhead}, config_z_hop: {config_z_hop}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={toolhead} SYNC=0
	PARK_TOOLHEAD
	
	
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={toolchange_standby_temp}
	{% endif %}
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=True
	{% endif %}
	
	
	_LED_TOOLHEAD_STANDBY TOOLHEAD={toolhead}

[gcode_macro _TOOLHEAD_WAKEUP]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set fan_speed = params.FAN_SPEED|float %}
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift_count = params.TOOLSHIFT_COUNT|default(0)|int %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% if toolshift_count == 1 %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% endif %}
	{% set needs_wakeup = true if printer["gcode_macro T%s" % toolhead].standby|default(false)|lower == 'true' else false %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Waking up toolhead T{toolhead}. Please wait for extruder to heat up..."
	DEBUG_ECHO PREFIX="_TOOLHEAD_WAKEUP" MSG="toolhead: {toolhead}, fan_speed: {fan_speed}, new_x: {new_x}, new_y: {new_y}, new_z: {new_z}, config_z_hop: {config_z_hop}"
	
	
	_LED_TOOLHEAD_WAKEUP TOOLHEAD={toolhead}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={toolhead} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE=1
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if toolhead == 0 else toolhead}
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if needs_wakeup %}
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set temp = extruder_first_layer_temp[toolhead]|float %}
	{% else %}
	{% set temp = extruder_other_layer_temp[toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if toolhead == 0 else 'extruder1'} MINIMUM={temp}  MAXIMUM={temp + 5}
	{% endif %}
	
	
	_LED_PRINTING TOOLHEAD={toolhead}
	
	
	{% if purge > 0 %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={toolhead} E={purge}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	
	
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if toolhead == 1 else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	G92 E0
	G1 E-{e} F{feedrate}
	G92 E0
	
	
	{% if new_x >= 0 and new_y >= 0 %}
	G1 X{new_x} Y{new_y} F{speed}
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={config_z_hop} T={toolhead} SYNC=0
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=False

[gcode_macro _TOOLCHANGE]
variable_toolshift_count = 0
gcode = 
	
	
	{% set new_t = params.T|default(-1)|int %}
	{% set new_x = params.X|default(-1.0)|float %}
	{% set new_y = params.Y|default(-1.0)|float %}
	{% set new_z = params.Z|default(-1.0)|float %}
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(true)|lower == 'true' else false %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T: {new_t}, X: {new_x}, Y: {new_y}, Z: {new_z}, PARK_T0: {park_t0}, PARK_T1: {park_t1}, IS_PRINTING_GCODE: {is_printing_gcode}, TOOLSHIFT: {toolshift}"
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	{% if park_t0 >= 0 and park_t1 >= 0 %}
	{% set parking_position_t0 = park_t0 %}
	{% set parking_position_t1 = park_t1 %}
	{% set parking_position_act_t = park_t0 if act_t == 0 else park_t1 %}
	{% endif %}
	
	
	{% if not is_printing_gcode and not toolshift %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Changing tool to T{new_t} without retracting/extruding or moving the toolheads except for parking."
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	G90
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% if not is_printing_gcode and toolshift and new_x < 0 and new_y < 0 %}
	{% set new_x = center_x %}
	{% set new_y = printer.gcode_move.gcode_position.y|float %}
	{% endif %}
	
	{% if new_x < 0 or new_y < 0 %}
	
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="No new X or Y position given, parking the active toolhead and activating the new toolhead without moving it."
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={new_t}
	
	
	{% if "x" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	{% if is_printing_gcode %}
	_EXTRUDE T={new_t}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	{% if "xyz" not in printer.toolhead.homed_axes %}
	
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	
	
	{% set svv = printer.save_variables.variables %}
	{% if new_t == default_toolhead %}
	{% set new_xoffset = 0 %}
	{% set new_yoffset = 0 %}
	{% set new_zoffset = 0 %}
	{% else %}
	{% set new_xoffset = -svv.idex_xoffset %}
	{% set new_yoffset = -svv.idex_yoffset %}
	{% set new_zoffset = -svv.idex_zoffset %}
	{% endif %}
	
	{% set xoffset_correction = new_xoffset - printer.named_offsets.toolhead_alignment.x %}
	{% set yoffset_correction = new_yoffset - printer.named_offsets.toolhead_alignment.y %}
	{% set zoffset_correction = new_zoffset - printer.named_offsets.toolhead_alignment.z %}
	
	{% if new_t == 0 %}
	
	{% set t0_act_x = parking_position_t0 %}
	{% set t1_act_x = printer.toolhead.position.x|float %}
	{% set t0_new_x = new_x %}
	{% set t1_new_x = parking_position_t1 %}
	{% set t0_distance = t0_new_x - t0_act_x %}
	{% set t1_distance = t1_new_x - t1_act_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T0."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	
	
	G1 X{t0_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x + (t1_new_x - t1_act_x)} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t0_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T0: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% elif new_t == 1 %}
	
	{% set t0_act_x = printer.toolhead.position.x|float %}
	{% set t1_act_x = parking_position_t1 %}
	{% set t0_new_x = parking_position_t0 %}
	{% set t1_new_x = new_x %}
	{% set t0_distance = t0_act_x - t0_new_x %}
	{% set t1_distance = t1_act_x - t1_new_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T1."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x - t1_distance + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t1_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T1: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% endif %}
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	{% endif %}

[gcode_macro _ZHOP_BEFORE_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_hop = params.Z_HOP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_HOP: {z_hop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="COMBINED_ZHOP G1 Z+{z_hop} E-{e} F{speed * 60}"
	G1 Z+{z_hop} E-{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="ZHOP G1 Z+{z_hop} F{speed * 60}"
	G1 Z+{z_hop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="RETRACT G1 E-{e} F{feedrate}"
	G1 E-{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _ZDROP_AFTER_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_drop = params.Z_DROP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_DROP: {z_drop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="COMBINED_ZDROP G1 Z-{z_drop} E{e} F{speed * 60}"
	G1 Z-{z_drop} E{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="ZDROP G1 Z-{z_drop} F{speed * 60}"
	G1 Z-{z_drop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="EXTRUDE G1 E{e} F{feedrate}"
	G1 E{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _EXTRUDE]
gcode = 
	
	{% set t = params.T|int %}
	
	
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	
	DEBUG_ECHO PREFIX="_EXTRUDE" MSG="G1 E{e} F{feedrate * 60}"
	
	
	G91
	M82
	G92 E0
	G1 E{e} F{feedrate * 60}
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _DEACTIVATE_TOOLHEAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_DEACTIVATE_TOOLHEAD" MSG="TOOLHEAD {toolhead}"
	
	
	{% if toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% endif %}
	
	
	M106.1 S0
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={toolhead}

[delayed_gcode _INIT_TOOLHEADS]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	_IDEX_SINGLE INIT=1
	
	
	{% if printer.fastconfig.settings.dual_carriage.safe_distance is defined %}
	{% if printer.fastconfig.settings.dual_carriage.safe_distance|float < 50 %}
	{ action_emergency_stop("Dual carriage safe_distance seems to be too low!") }
	{% endif %}
	{% else %}
	{ action_emergency_stop("Dual carriage safe_distance not defined!") }
	{% endif %}

[gcode_macro _SET_TOOLHEAD_OFFSET]
description = "Internal use only. Sets the toolhead_alignment offset (and hotend_thermal_expansion offset when configured) for the active/dominant toolhead."
gcode = 
	
	{% set move = params.MOVE|default(0)|int %}
	{% set force_toolhead = params.FORCE_TOOLHEAD|default(-1)|int %}
	
	
	{% if params.T is defined %}
	CONSOLE_ECHO TYPE="error" MSG="_SET_TOOLHEAD_OFFSET called with deprectated T parameter, which is ignored."
	{';$_SET_TOOLHEAD_OFFSET_ignoring_TOOLHEAD_parameter'}
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="active/dominant toolhead: {toolhead}, MOVE: {move}, FORCE_TOOLHEAD: {force_toolhead}"
	
	
	{% if force_toolhead >= 0 %}
	{% set toolhead = force_toolhead %}
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="FORCE_TOOLHEAD applied, using TOOLHEAD: {toolhead}"
	{% endif %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set move = 0 %}
	{% endif %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|int %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X=0 Y=0 MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z=0 MOVE={move} SPEED={z_speed}
	{% else %}
	{% set svv = printer.save_variables.variables %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X={(-svv.idex_xoffset)} Y={(-svv.idex_yoffset)} MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-svv.idex_zoffset)} MOVE={move} SPEED={z_speed}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}

[gcode_macro TOOLSHIFT_CONFIG]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={params.SPEED|default(300)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={params.ACCEL|default(5000)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_retraction VALUE={params.RETRACT|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_extrusion VALUE={params.EXTRUDE|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_feedrate VALUE={params.FEEDRATE|default(7200)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={params.Z_HOP|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zspeed VALUE={params.Z_SPEED|default(25)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_combined_zhop VALUE={true if params.COMBINED_ZHOP|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_sync_fans VALUE={true if params.SYNC_FANS|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_prepurging_timer VALUE={params.AUTO_PURGE_TIME|default(0)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_purge VALUE={params.PURGE|default(25)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_standby_temp VALUE={params.STANDBY_TEMP|default(-1)|float}

[gcode_macro CALCULATE_DC_ENDSTOP]
description = "DEPRECATED: This macro has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."
gcode = 
	CONSOLE_ECHO TITLE="CALCULATE_DC_ENDSTOP has been deprecated" TYPE="error" MSG="The CALCULATE_DC_ENDSTOP has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."

[gcode_macro _VAOC]
variable_is_fixed = True
variable_is_started = False
variable_is_started_at_temp = False
variable_additional_safe_distance = 50
variable_safe_z = 30
variable_auto_z_offset_calibration = True
variable_enable_camera_cooling = True
variable_camera_cooling_fan_speed = 0.3
variable_camera_cooling_temperature = 50
variable_toolchange_travel_speed = 300
variable_toolchange_travel_accel = 5000
variable_adjusting_secondary_toolhead_focus_adjusts_zoffset = False
variable_cache_toolchange_travel_speed = 300
variable_cache_toolchange_travel_accel = 5000
variable_cache_toolchange_zhop = 1.0
variable_t0_toolhead_sensor_enabled = 0
variable_t1_toolhead_sensor_enabled = 0
variable_t0_bowden_sensor_enabled = 0
variable_t1_bowden_sensor_enabled = 0
variable_loaded_skew_profile = ""
variable_gcode_z_offset = 0.0
variable_start_x_offset = 0.0
variable_start_y_offset = 0.0
gcode = 
	_ECHO_VAOC_VARS
variable_expected_camera_x_position = 212.5
variable_expected_camera_y_position = 530.5

[gcode_macro _VAOC_START]
description = Called from the front end. If T0_TEMP, T1_TEMP and BED_TEMP parameter are specified, VAOC calibration will start under real conditions at printing temp.
gcode = 
	
	{% set t0_temp = params.T0_TEMP|default(0)|int %}
	{% set t1_temp = params.T1_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(0)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro SKEW_PROFILE"].loaded_profile|default("") %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=loaded_skew_profile VALUE='"{loaded_skew_profile}"'
	
	
	{% if t0_temp > 0 and t1_temp > 0 and bed_temp > 0 %}
	
	
	{% if not is_fixed %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("VAOC calibration at temp works only with a fixed installed VAOC device.") }
	{% endif %}
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE=0
	{% endif %}
	
	
	START_PRINT EXTRUDER_TEMP={t0_temp},{t1_temp} EXTRUDER_OTHER_LAYER_TEMP={t0_temp},{t1_temp} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp} INITIAL_TOOL=0 TOTAL_LAYER_COUNT=1 X0={(printable_x_max / 2 - 10)} Y0={(printable_y_max / 2 - 10)} X1={(printable_x_max / 2 + 10)} Y1={(printable_y_max / 2 + 10)} TOTAL_TOOLSHIFTS=1 FIRST_X={printable_x_max / 2} FIRST_Y={printable_y_max / 2} MIN_X={(printable_x_max / 2 - 10)} MAX_X={(printable_x_max / 2 + 10)} USED_TOOLS=0,1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=True
	
	{% endif %}
	
	
	_START_VAOC

[gcode_macro _START_VAOC]
description = Called from _VAOC_START. Do not call it manually.
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(printable_x_max/2)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(printable_y_max/2)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	DEBUG_ECHO PREFIX="VAOC_START" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, zcontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_x_offset VALUE={svv.idex_xoffset|default(0.0)|float}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_y_offset VALUE={svv.idex_yoffset|default(0.0)|float}
	
	
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_SAFE_Z_HEIGHT
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_speed VALUE={printer["gcode_macro RatOS"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_accel VALUE={printer["gcode_macro RatOS"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_zhop VALUE={printer["gcode_macro RatOS"].toolchange_zhop|float}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE=0
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"START X_REFERENCE:%.6f Y_REFERENCE:%.6f Z_REFERENCE:%.6f PARK_T0:%.6f PARK_T1:%.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, parking_position_t0, parking_position_t1)}
	
	
	_LED_VAOC_ON
	
	
	
	
	
	
	
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=gcode_z_offset VALUE={printer.gcode_move.homing_origin.z}
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z=0
	
	
	MAYBE_HOME
	M400
	
	
	_LOAD_RATOS_SKEW_PROFILE
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	IDEX_SINGLE
	{% endif %}
	
	
	
	SAVE_GCODE_STATE NAME=vaoc_state
	
	
	RESET_NAMED_OFFSET EVENT=reset_all
	
	
	{% if is_fixed %}
	_SELECT_TOOL T=0 TOOLSHIFT=false
	{% if default_toolhead == 0 %}
	G1 X{idex_xcontrolpoint} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint + safe_distance + additional_safe_distance} F{speed}
	{% else %}
	G1 X{idex_xcontrolpoint - safe_distance - additional_safe_distance} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint} F{speed}
	{% endif %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	{% else %}
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	G1 X{idex_xcontrolpoint} F{speed}
	G1 Y{idex_ycontrolpoint} F{speed}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	
	
	_SELECT_TOOL T={default_toolhead} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	{% if not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={default_toolhead}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=True

[gcode_macro _VAOC_END]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_y = printable_y_max / 2 %}
	{% set saved_gcode_z_offset = printer["gcode_macro _VAOC"].gcode_z_offset|default(0.0)|float %}
	
	DEBUG_ECHO PREFIX="_VAOC_END" MSG="printable_y_max: {printable_y_max}, center_y: {center_y}, safe_z: {safe_z}"
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% set x_offset_change = svv.idex_xoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_x_offset|default(0.0)|float %}
	{% set y_offset_change = svv.idex_yoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_y_offset|default(0.0)|float %}
	{% set offset_change_norm = (x_offset_change ** 2 + y_offset_change ** 2) ** 0.5 %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="VAOC calibration changed the relative XY offset between T0 and T1 by {offset_change_norm|round(3)} mm (ΔX: {x_offset_change|round(3)}, ΔY: {y_offset_change|round(3)})"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	G1 Y{center_y} F{speed}
	
	
	_IDEX_SINGLE INIT=1
	
	
	_LED_VAOC_OFF
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={printer["gcode_macro _VAOC"].cache_toolchange_zhop|float}
	
	
	{% if printer["gcode_macro _VAOC"].is_started_at_temp|default(true)|lower == 'true' %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_bowden_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_bowden_sensor_enabled|int}
	{% endif %}
	{% endif %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro _VAOC"].loaded_skew_profile|default("") %}
	{% if loaded_skew_profile != "" %}
	SKEW_PROFILE LOAD={loaded_skew_profile}
	{% else %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=vaoc_state
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z={saved_gcode_z_offset}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False

[gcode_macro _VAOC_LOAD_TOOL]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set auto_temp_offset = true if params.AUTO_TEMP_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set toolhead_zoffset = svv.idex_zoffset|default(0)|float %}
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move T%s to control point: X%.6f Y%.6f Z%.6f IS_FIXED=%s"' % (t, idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, is_fixed)}
	
	
	{% if not auto_temp_offset and not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={t}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	{% set current_z = printer.toolhead.position.z|float %}
	{% set lowest_toolhead_z = [current_z, current_z - toolhead_zoffset]|min %}
	{% if lowest_toolhead_z < safe_z %}
	G1 Z{[safe_z, safe_z + toolhead_zoffset]|max} F{z_speed}
	{% else %}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	{% endif %}
	
	
	_SELECT_TOOL T={t} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_SET_CAMERA_COOLING]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	
	
	{% set enable_camera_cooling = true if printer["gcode_macro _VAOC"].enable_camera_cooling|default(true)|lower == 'true' else false %}
	{% set camera_cooling_temperature = printer["gcode_macro _VAOC"].camera_cooling_temperature|float %}
	{% set camera_cooling_fan_speed = printer["gcode_macro _VAOC"].camera_cooling_fan_speed|float %}
	
	
	{% if printer.heater_bed.temperature >= camera_cooling_temperature and enable_camera_cooling %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={camera_cooling_fan_speed if t == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={camera_cooling_fan_speed if t == 1 else 0}
	
	
	M106.1 S{camera_cooling_fan_speed}
	
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	{% endif %}

[gcode_macro _VAOC_SET_TOOL]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="_VAOC_SET_TOOL" MSG="IDEX_MODE: {idex_mode}, TOOLHEAD: {toolhead}"
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	{% set x = printer.gcode_move.gcode_position.x|float %}
	{% set y = printer.gcode_move.gcode_position.y|float %}
	{% set z = printer.gcode_move.gcode_position.z|float %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE={x}
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE={y}
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE={z}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Control point was set: X%.6f Y%.6f Z%.6f"' % (x, y, z)}
	
	{% else %}
	
	
	
	{% set move_diff_x = printer.gcode_move.gcode_position.x|float - svv.idex_xcontrolpoint|float %}
	{% set move_diff_y = printer.gcode_move.gcode_position.y|float - svv.idex_ycontrolpoint|float %}
	{% set move_diff_z = printer.gcode_move.gcode_position.z|float - svv.idex_zcontrolpoint|float %}
	
	
	{% set new_x_offset = svv.idex_xoffset - move_diff_x %}
	{% set new_y_offset = svv.idex_yoffset - move_diff_y %}
	{% set new_z_offset = svv.idex_zoffset - move_diff_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE={new_x_offset}
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE={new_y_offset}
	
	{% set z_focus_msg = "" %}
	{% if move_diff_z|abs > 1e-6 %}
	{% if printer["gcode_macro _VAOC"].adjusting_secondary_toolhead_focus_adjusts_zoffset|default(false)|lower == 'true' %}
	{% set z_focus_msg = " (Z offset adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={new_z_offset}
	{% else %}
	{% set z_focus_msg = " (Z offset not adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	{% set new_z_offset = svv.idex_zoffset %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset was set: X%.6f Y%.6f Z%.6f%s"' % (toolhead, new_x_offset, new_y_offset, new_z_offset, z_focus_msg)}
	
	{% endif %}

[gcode_macro _VAOC_MOVE]
gcode = 
	
	{% set x = params.X|default(0)|float %}
	{% set y = params.Y|default(0)|float %}
	{% set z = params.Z|default(0)|float %}
	
	
	G91
	{% if z != 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 Z%.6f F300"' % (z)}
	G1 Z{z} F300
	
	{% else %}
	{% if x <=2 and y <=2 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 X%.6f Y%.6f F18000"' % (x, y)}
	G1 X{x} Y{y} F18000
	{% endif %}
	{% endif %}
	G90

[gcode_macro _VAOC_CALIBRATE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	{% if printer["z_offset_probe"] is defined and is_started %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	
	{% if auto_z_offset %}
	_START_VAOC AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_END
	{% else %}
	_VAOC_LOAD_TOOL T={default_toolhead}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	{% endif %}
	
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_Z_OFFSET
	
	{% endif %}

[gcode_macro _VAOC_PROBE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}
	{% if not auto_z_offset %}
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	{% endif %}
	M400
	_VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT

[gcode_macro _VAOC_Z_OFFSET_PROBE_CURRENT_POSITION]
gcode = 
	
	Z_OFFSET_PROBE PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_DROP=1 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median

[gcode_macro _VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT]
gcode = 
	{% if printer["z_offset_probe"] is defined %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE={last_z}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Z-offset control point set:: %.6f"' % last_z}
	
	{% else %}
	
	
	
	{% set z = svv.idex_zoffsetcontrolpoint|float - last_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={z}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-z)}
	
	
	G0 Z{svv.idex_zcontrolpoint|float} F{z_speed}
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset set: Z %.6f"' % (t, z)}
	
	{% endif %}
	
	{% endif %}

[gcode_macro _VAOC_ECHO_Z_OFFSET]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s toolhead z-offset %.6f"' % (1 if default_toolhead == 0 else 0, svv.idex_zoffset)}
	{% if svv.idex_zoffset|abs < 0.02 %}
	CONSOLE_ECHO TITLE={'"Perfect toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="You have a perfect toolhead z-offset!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.02 and svv.idex_zoffset|abs < 0.05 %}
	CONSOLE_ECHO TITLE={'"Good toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is good!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.05 and svv.idex_zoffset|abs < 0.1 %}
	CONSOLE_ECHO TITLE={'"High toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset could be better._N_Use minimum 0.3mm first layer height for copy and mirror mode prints." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.1 and svv.idex_zoffset|abs < 0.2 %}
	CONSOLE_ECHO TITLE={'"Bad toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is bad._N_Copy and mirror mode prints are not recommended with it." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.2 %}
	CONSOLE_ECHO TITLE={'"Unacceptable toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is unacceptable._N_Do not print in copy and mirror mode with it." TYPE="alert"
	{% endif %}
	RATOS_ECHO PREFIX="VAOC" MSG="Toolhead z-offset calibration done!"

[gcode_macro _VAOC_CALIBRATE_TEMP_OFFSET]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if is_fixed and is_started and printer["z_offset_probe"] is defined and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	_VAOC_LOAD_TOOL T={default_toolhead} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_NOZZLE_TEMP_OFFSETS
	
	{% endif %}

[gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET=0
	
	
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	M400

[gcode_macro _VAOC_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(150)|float %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Probing with nozzle temperature {temp}°C..."
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	
	
	G0 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _VAOC_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set msg = '"T0 expansion coefficient %.6fmm_N_T1 expansion coefficient %.6fmm"' % (svv.nozzle_expansion_coefficient_t0, svv.nozzle_expansion_coefficient_t1) %}
	CONSOLE_ECHO TITLE="Nozzle expansion coefficients:" MSG={msg} TYPE="success"

[gcode_macro _VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - expected_camera_x_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC x-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_xcontrolpoint, expected_camera_x_position)) }
	{% endif %}
	{% if (idex_ycontrolpoint - expected_camera_y_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC y-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_ycontrolpoint, expected_camera_y_position)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - printer.gcode_move.gcode_position.x|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected y-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_xcontrolpoint, printer.gcode_move.gcode_position.x|float)) }
	{% endif %}
	{% if (idex_ycontrolpoint - printer.gcode_move.gcode_position.y|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected x-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_ycontrolpoint, printer.gcode_move.gcode_position.y|float)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_SAFE_Z_HEIGHT]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set idex_zoffsetcontrolpoint = svv.idex_zoffsetcontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_SAFE_Z_HEIGHT" MSG={'"idex_zcontrolpoint: %.6f, idex_zoffsetcontrolpoint: %.6f"' % (idex_zcontrolpoint, idex_zoffsetcontrolpoint)}
	
	{% if safe_z < idex_zcontrolpoint + 2 or safe_z < idex_zoffsetcontrolpoint + 2 %}
	{action_raise_error("VAOC safe_z value (%.3f) is too low, it must be higher than %.3f" % (safe_z, [idex_zoffsetcontrolpoint + 2, idex_zcontrolpoint + 2]|max))}
	{% endif %}

[gcode_macro _VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED]
gcode = 
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T0. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T1. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_RESET]
gcode = 
	DEBUG_ECHO PREFIX="_VAOC_RESET" MSG="running template-emitted _VAOC_RESET macro"
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE=212.5
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE=530.5
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE=10
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE=0
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE=0.0
	
	RESET_DC_ENDSTOP_CONFIGURATION
	RESET_Y_MAX_ADJUSTMENT
	
	
	CONSOLE_ECHO TITLE="VAOC Configuration Reset" MSG="VAOC configuration has been reset. You must RESTART klipper for the changes to take effect,_N_then re-calibrate VAOC."

[gcode_macro _ECHO_VAOC_VARS]
description = Echo VAOC variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro _VAOC"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro _VAOC_SWITCH_LED]
gcode = 
	{% if params.STATE|default(0)|int == 1 %}
	_LED_VAOC_ON
	{% else %}
	_LED_VAOC_OFF
	{% endif %}

[gcode_macro Z_PROBE_TEST_T0]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T0
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST_T1]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T1
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	
	
	_VAOC_Z_PROBE_TEST_EVALUATE
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro _VAOC_Z_PROBE_LOOP]
gcode = 
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_SHAKE_IT
	_VAOC_START

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if primary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T0. Retried {primary_retries} time(s)."
	{% endif %}
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	
	{% if (primary_range - secondary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 is drifting significantly more than T1."
	{% endif %}
	{% if (secondary_range - primary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 is drifting significantly more than T0."
	{% endif %}
	
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T0]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T1]
gcode = 
	
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _SHAKE_IT]
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	_Z_HOP
	{% for i in range(3) %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 + 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 + 1}
	{% endfor %}
	{% for i in range(2) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 + 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 + 50}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 1}
	{% endfor %}
	{% endfor %}

[gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 retries updated: {new_retries}"

[gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 retries updated: {new_retries}"

[gcode_macro _CLEAR_PRIMARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _CLEAR_SECONDARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _VAOC_TEST_Z_OFFSET]
gcode = 
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}

[delayed_gcode _IDEX_INIT]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	VERIFY_HYBRID_INVERTED

[gcode_macro Z_TILT_ADJUST]
rename_existing = Z_TILT_ADJUST_ORIG
gcode = 
	
	{% set beacon_contact_z_tilt_adjust_samples = printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust_samples|default(2)|int %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(true)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	_IDEX_SINGLE
	
	_SELECT_TOOL T={printer["gcode_macro RatOS"].default_toolhead|default(0)|int} TOOLSHIFT=false
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_tilt_adjust %}
	Z_TILT_ADJUST_ORIG PROBE_METHOD=contact SAMPLES={beacon_contact_z_tilt_adjust_samples}
	{% else %}
	Z_TILT_ADJUST_ORIG
	{% endif %}
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if idex_mode == "copy" %}
	_IDEX_COPY
	{% elif idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[stepper_x]
position_max = 500
position_endstop = -59.6
position_min = -59.6
step_pin = PF13
dir_pin = x_dir_pin
enable_pin = !PF14
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t0:PA2

[stepper_y]
position_max = 533.65
position_min = -14.35
position_endstop = -14.35
step_pin = PG0
dir_pin = !y_dir_pin
enable_pin = !PF15
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = PG9

[stepper_z]
position_max = 500
position_min = -7
step_pin = PC13
dir_pin = !z0_dir_pin
enable_pin = !PF1
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4
homing_speed = 10
endstop_pin = probe:z_virtual_endstop

[z_tilt]
z_positions = 
	0,0
	250,500
	500,0
points = 
	20, 10
	480, 230
	20, 450
horizontal_move_z = 20
retries = 10
retry_tolerance = 0.02
speed = 600

[extruder]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t0:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t0:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t0:PD3
dir_pin = toolboard_t0:e_dir_pin
enable_pin = !toolboard_t0:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[firmware_retraction]
retract_speed = 60
unretract_extra_length = 0
unretract_speed = 60
retract_length = 0.2

[extruder1]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t1:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t1:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t1:PD3
dir_pin = toolboard_t1:e_dir_pin
enable_pin = !toolboard_t1:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[resonance_tester]
accel_chip_x = lis2dw toolboard_t0
accel_chip_y = lis2dw toolboard_t0
probe_points = 
	250,250,20

[tmc5160 stepper_x]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC4
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 dual_carriage]
stealthchop_threshold = 0
interpolate = True
cs_pin = PF2
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y]
stealthchop_threshold = 0
interpolate = True
cs_pin = PD11
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y1]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC7
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[stepper_y1]
step_pin = PG4
dir_pin = y1_dir_pin
enable_pin = !PA2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46

[tmc2209 stepper_z]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE4
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[tmc2209 stepper_z1]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE1
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z1]
step_pin = PE2
dir_pin = !z1_dir_pin
enable_pin = !PD4
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 stepper_z2]
stealthchop_threshold = 0
interpolate = True
uart_pin = PD3
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z2]
step_pin = PE6
dir_pin = !z2_dir_pin
enable_pin = !PE0
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 extruder]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t0:PB3
run_current = 0.707
sense_resistor = 0.11

[tmc2209 extruder1]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t1:PB3
run_current = 0.707
sense_resistor = 0.11

[beacon]
serial = /dev/beacon
x_offset = 0
y_offset = 27.5
mesh_main_direction = x
mesh_runs = 1
mesh_cluster_size = 0
speed = 15.
lift_speed = 80.
contact_max_hotend_temperature = 275
contact_mesh_min = 20,20
contact_mesh_max = 480,480

[beacon_user_z_offset]

[beacon_mesh]

[beacon_true_zero_correction]

[beacon_adaptive_heat_soak]

[delayed_gcode _BEACON_INIT]
initial_duration = 1
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	_BEACON_MESH_INIT
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_coefficient_multiplier
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_applied_offset
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=beacon_saved_runtime_offset
	{% if printer["gcode_macro RatOS"].beacon_contact_expansion_multiplier is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_contact_expansion_multiplier is no longer used, please remove it from your config file."
	{% endif %}
	{% if printer["gcode_macro RatOS"].beacon_scan_compensation_resolution is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_scan_compensation_resolution is no longer used, please remove it from your config file."
	{% endif %}

[gcode_macro BEACON_RATOS_CALIBRATION]
gcode = 
	RATOS_ECHO MSG="Did you mean BEACON_RATOS_CALIBRATE?"

[gcode_macro BEACON_RATOS_CALIBRATE]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	BEACON_INITIAL_CALIBRATION _AUTOMATED=True
	
	{% if beacon_contact_start_print_true_zero %}
	BEACON_POKE_TEST _AUTOMATED=True
	_BEACON_CHECK_POKE
	{% if printer["dual_carriage"] is not defined %}
	BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET _AUTOMATED=True
	{% endif %}
	{% endif %}
	
	{% set already_heated = False %}
	
	
	{% if beacon_contact_start_print_true_zero and beacon_scan_compensation_enable %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% set already_heated = True %}
	{% endif %}
	
	
	BEACON_FINAL_CALIBRATION _AUTOMATED=True _AUTOMATED_ALREADY_HEATED={already_heated} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	{% if beacon_contact_start_print_true_zero %}
	{% if printer["dual_carriage"] is not defined %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	_BEACON_ECHO_POKE
	{% endif %}
	RATOS_ECHO MSG="Beacon calibration finished!"
	
	
	_LED_BEACON_CALIBRATION_END
	
	
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG

[gcode_macro BEACON_INITIAL_CALIBRATION]
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Initial beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro BEACON_FINAL_CALIBRATION]
description = Runs BEACON_AUTO_CALIBRATE after heating the bed and chamber to specified temperatures. This creates a beacon model under reference conditions for future use.
	This macro will skip calibration if both the beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero settings are enabled, because a new
	model will be calibrated automatically at the start of each print. Use FORCE=True to override this check.
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set already_heated = true if params._AUTOMATED_ALREADY_HEATED|default(false)|lower == 'true' else false %}
	{% set force = params.FORCE|default('false')|lower in ('1', 'true', 'yes') %}
	
	
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default('false')|lower == "true" %}
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero and not force %}
	RATOS_ECHO MSG="BEACON_FINAL_CALIBRATION skipped, not needed because beacon_contact_calibrate_model_on_true_zero is enabled. Use FORCE=True to override."
	{% else %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	{% if chamber_temp > 0 and not already_heated %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	{% if not already_heated %}
	
	G0 Z2.5 F{z_hop_speed}
	
	
	RATOS_ECHO MSG="Waiting for calibration temperature..."
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	{% if beacon_adaptive_heat_soak %}
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,3600]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_Z_HOP
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Final beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	{% endif %}

[gcode_macro BEACON_POKE_TEST]
variable_poke_result_1 = -1
variable_poke_result_2 = -1
variable_poke_result_3 = -1
variable_poke_result_4 = -1
variable_poke_result_5 = -1
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_1 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_2 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_3 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_4 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_5 VALUE=-1
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G0 Z5 F{z_hop_speed}
	
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=1
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=2
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=3
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=4
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=5
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Beacon poke test finished!"
	{% if not automated %}
	_BEACON_ECHO_POKE
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro _BEACON_PROBE_POKE]
gcode = 
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	BEACON_POKE speed=3 top=5 bottom={poke_bottom}
	BEACON_QUERY

[gcode_macro _BEACON_STORE_POKE]
gcode = 
	
	{% set i = params.I|default(1)|int %}
	
	
	{% set last_z = printer.beacon.last_poke_result|default(0)|float %}
	
	
	{% if printer.beacon.last_poke_result|lower != "none" %}
	{% if printer.beacon.last_poke_result.error == 0 %}
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE={"poke_result_%s" % i} VALUE={printer.beacon.last_poke_result.latency}
	{% endif %}
	{% endif %}

[gcode_macro _BEACON_CHECK_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% if p1 == -1 or p2 == -1 or p3 == -1 or p4 == -1 or p5 == -1 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test error!") }
	{% endif %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	{% if avg > 6 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test failed!") }
	{% endif %}

[gcode_macro _BEACON_ECHO_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	
	
	{% if avg <= 1 %}
	{% set type = "success" %}
	{% set note = "Extremely low noise, rarely achieved" %}
	{% elif avg > 1 and avg <= 4 %}
	{% set type = "info" %}
	{% set note = "Excellent performance for a typical printer" %}
	{% elif avg > 4 and avg <= 8 %}
	{% set type = "warning" %}
	{% set note = "Acceptable performance, machine may have considerable cyclic axis noise" %}
	{% elif avg > 8 and avg <= 11 %}
	{% set type = "alert" %}
	{% set note = "Not ideal, may want to verify proper mounting or use thinner stackups" %}
	{% elif avg > 11 %}
	{% set type = "alert" %}
	{% set note = "Reason for concern, present setup may be risky to continue with" %}
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon poke test result:" TYPE={type} MSG={'"Average latency: %.2f_N_%s"' % (avg, note)}

[gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Nozzle temperature offset calibration..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET=0
	
	
	{% if not automated %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing with nozzle temperature {temp}°C..."
	PROBE PROBE_METHOD=contact PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median
	BEACON_QUERY
	
	
	G0 Z5 F{z_speed}

[gcode_macro _BEACON_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer.beacon.last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{default_toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% if default_toolhead == 0 %}
	CONSOLE_ECHO TYPE="info" MSG={'"T0 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t0}
	{% else %}
	CONSOLE_ECHO TYPE="info" MSG={'"T1 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t1}
	{% endif %}

[gcode_macro _BEACON_SET_NOZZLE_TEMP_OFFSET]
description = "Set the thermal expansion z offset for the active toolhead based on the current extruder target temperature and thermal expansion coefficient."
gcode = 
	{% if params.RESET is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The RESET parameter is no longer supported and has no effect."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% if params.TOOLHEAD is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The TOOLHEAD parameter is no longer supported and has no effect. The macro now automatically determines the current toolhead."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	{% if beacon_contact_expansion_compensation %}
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set nozzle_expansion_coefficient_t0 = svv.nozzle_expansion_coefficient_t0|default(0)|float %}
	{% if printer["dual_carriage"] is defined %}
	{% set nozzle_expansion_coefficient_t1 = svv.nozzle_expansion_coefficient_t1|default(0)|float %}
	{% endif %}
	
	
	{% set temp = printer['extruder' if toolhead == 0 else 'extruder1'].target|float %}
	
	
	{% set temp_delta = temp - beacon_contact_true_zero_temp %}
	{% set expansion_coefficient = nozzle_expansion_coefficient_t0 if toolhead == 0 else nozzle_expansion_coefficient_t1 %}
	{% set expansion_offset = temp_delta * (expansion_coefficient / 100) %}
	
	
	SET_NAMED_OFFSET NAME=hotend_thermal_expansion Z={expansion_offset} MOVE=1 MOVE_SPEED={z_speed}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG={'"Nozzle expansion offset of %.6fmm applied to T%s"' % (expansion_offset, toolhead)}
	DEBUG_ECHO PREFIX="_BEACON_SET_NOZZLE_TEMP_OFFSET" MSG="toolhead: {toolhead}, coefficient: {expansion_coefficient|round(6)}, temp_delta: {temp_delta|round(1)},  expansion_offset: {expansion_offset|round(6)}"
	
	{% endif %}

[gcode_macro BEACON_MEASURE_BEACON_OFFSET]
variable_needs_compensation = False
variable_reference_z = 0.0
variable_front = 0.0
variable_front_left = 0.0
variable_front_right = 0.0
variable_back = 0.0
variable_back_left = 0.0
variable_back_right = 0.0
variable_right = 0.0
variable_left = 0.0
variable_margin_x = 40
variable_margin_y = 40
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=False
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Measure beacon offset..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="center"
	
	
	G0 X{margin_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_left"
	
	
	G0 X{safe_home_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front"
	
	
	G0 X{(printable_x_max - margin_x)} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_right"
	
	
	G0 X{safe_home_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back"
	
	
	G0 X{margin_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_left"
	
	
	G0 X{margin_x} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="left"
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_BEACON_ECHO_BEACON_OFFSET
	
	
	_LED_BEACON_CALIBRATION_END
	
	{% endif %}

[gcode_macro _BEACON_STORE_BEACON_OFFSET]
gcode = 
	
	{% set location = params.LOCATION|lower %}
	
	
	{% set last_z = printer.beacon.last_offset_result["delta"]|default(0)|float %}
	
	
	{% if location == "center" %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE={location} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_BEACON_OFFSET]
gcode = 
	
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float * 1000 %}
	{% set front_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_left|default(0)|float * 1000 %}
	{% set front = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front|default(0)|float * 1000 %}
	{% set front_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_right|default(0)|float * 1000 %}
	{% set right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].right|default(0)|float * 1000 %}
	{% set back_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_right|default(0)|float * 1000 %}
	{% set back = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back|default(0)|float * 1000 %}
	{% set back_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_left|default(0)|float * 1000 %}
	{% set left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].left|default(0)|float * 1000 %}
	
	{% set line_1 = "Front left:    %.6fμm" % (front_left) %}
	{% set line_2 = "Front center:  %.6fμm" % (front) %}
	{% set line_3 = "Front right:   %.6fμm" % (front_right) %}
	{% set line_4 = "Left center:   %.6fμm" % (left) %}
	{% set line_5 = "Right center:  %.6fμm" % (right) %}
	{% set line_6 = "Back left:     %.6fμm" % (back_left) %}
	{% set line_7 = "Back center:   %.6fμm" % (back) %}
	{% set line_8 = "Back right:    %.6fμm" % (back_right) %}
	
	{% set max_value = [(front_left|abs), (front|abs), (front_right|abs), (left|abs), (right|abs), (back_left|abs), (back|abs), (back_right|abs)]|max %}
	{% if max_value <= 50 %}
	{% set type = "success" %}
	{% set recommendation = "Very low beacon offset: %.6fμm._N_No beacon scan compensation needed." % max_value %}
	{% elif max_value > 50 and max_value <= 100 %}
	{% set type = "info" %}
	{% set recommendation = "Low beacon offset: %.6fμm._N_You may experience first layer inconsistensies, consider beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 100 and max_value <= 150 %}
	{% set type = "warning" %}
	{% set recommendation = "High beacon offset: %.6fμm._N_High chance of first layer problems, beacon scan compensation is highly encouraged." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 150 and max_value <= 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Very High beacon offset: %.6fμm._N_You will encounter first layer problems on large prints unless you activate beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Extremely high beacon offset: %.6fμm._N_You have significant scan/contact inconsistency which is indicative of mechanical problems, please investigate before resorting to software compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon offset relative to the center" TYPE={type} MSG={'"_N_%s_N__N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s"' % (recommendation, line_1, line_2, line_3, line_4, line_5, line_6, line_7, line_8)}

[gcode_macro BEACON_CREATE_SCAN_COMPENSATION_MESH]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set profile = params.PROFILE|default("auto")|string %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set keep_temp_meshes = params.KEEP_TEMP_MESHES|default(0) %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' %}
	{% set desired_spacing = printer["gcode_macro RatOS"].beacon_scan_compensation_desired_spacing|float %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	
	{% if not beacon_scan_compensation_enable %}
	RATOS_ECHO MSG="Beacon scan compensation is disabled!"
	
	{% else %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	
	
	RATOS_ECHO MSG="Please wait..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	G1 Z2.5 F{z_speed}
	{% if beacon_adaptive_heat_soak %}
	
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,9000]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if not (beacon_adaptive_heat_soak or bed_heat_soak_time > 0) %}
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if printer.z_tilt is defined %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% endif %}
	{% if printer.quad_gantry_level is defined %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% endif %}
	
	
	_BEACON_CREATE_SCAN_COMPENSATION_MESH_CORE PROFILE="{profile}" DESIRED_SPACING={desired_spacing} CHAMBER_TEMP={chamber_temp} KEEP_TEMP_MESHES={keep_temp_meshes}
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	{% if automated %}
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon scan compensation mesh created!"
	
	
	{% if not automated %}
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED]
gcode = 
	
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED" MSG="beacon_scan_compensation_profile {beacon_scan_compensation_profile}, beacon_scan_compensation_enable {beacon_scan_compensation_enable}"
	
	{% if beacon_scan_compensation_enable %}
	BEACON_APPLY_SCAN_COMPENSATION PROFILE="{beacon_scan_compensation_profile}"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL]
gcode = 
	
	{% set beacon_contact_start_print_true_zero = params.BEACON_CONTACT_START_PRINT_TRUE_ZERO|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = params.beacon_contact_calibrate_model_on_true_zero|lower == 'true' %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and not printer.beacon.model %}
	{% set beacon_model_required_for_true_zero = beacon_contact_start_print_true_zero and not beacon_contact_calibrate_model_on_true_zero %}
	{% set beacon_model_required_for_homing =
	printer.fastconfig.settings.stepper_z.endstop_pin == 'probe:z_virtual_endstop'
	and (( printer.fastconfig.settings.beacon.home_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower != 'true')
	or ( printer.fastconfig.settings.beacon.default_probe_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower != 'true' )) %}
	{% if beacon_model_required_for_homing or beacon_model_required_for_true_zero %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("An active Beacon model is required. Have you performed initial Beacon calibration?") }
	{% endif %}
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION]
gcode = 
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set bed_temp_mismatch_is_error = true if printer["gcode_macro RatOS"].beacon_scan_compensation_bed_temp_mismatch_is_error|default(false)|lower == 'true' else false %}
	
	{% set bed_temp = params.BED_TEMP|default(0)|float %}
	{% if bed_temp == 0 %}
	{% set bed_temp = printer.heater_bed.temperature %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_PREFLIGHT_CHECK_BEACON" MSG="beacon_scan_compensation_profile={beacon_scan_compensation_profile}, beacon_scan_compensation_enable={beacon_scan_compensation_enable}, bed_temp={bed_temp}"
	
	{% if beacon_scan_compensation_enable %}
	_VALIDATE_COMPENSATION_MESH_PROFILE PROFILE="{beacon_scan_compensation_profile}" TITLE="Check Beacon scan compensation profile" SUBJECT="Configured compensation profile '{beacon_scan_compensation_profile}'" COMPARE_BED_TEMP={bed_temp} COMPARE_BED_TEMP_IS_ERROR={bed_temp_mismatch_is_error}
	{% endif %}

[gcode_macro _BEACON_MAYBE_SCAN_COMPENSATION]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set needs_scan_compensation = true if printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].needs_compensation|default(false)|lower == 'true' else false %}
	
	{% if needs_scan_compensation %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% endif %}

[gcode_macro _BEACON_HOME_AND_ABL]
gcode = 
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	{% if needs_rehoming %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}

[gcode_macro SAVE_Z_OFFSET]
description = Deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead, or in Mainsail use the SAVE button in the Z-OFFSET section.
gcode = 
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default('false')|lower == 'true' %}
	{% set msg = "SAVE_Z_OFFSET is deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead,_N_or in Mainsail use the SAVE button in the Z-OFFSET section."%}
	{% if not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% set msg = msg + "_N_You must then use the SAVE_CONFIG command to persist the change." %}
	{% endif %}
	CONSOLE_ECHO TYPE="error" MSG="{msg}"

[gcode_macro _BEACON_OFFSET_COMPARE]
gcode = 
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing..."
	
	
	BEACON_OFFSET_COMPARE SAMPLES_DROP=1 SAMPLES=3
	BEACON_QUERY

[fan]
pin = rpi:gpio4

[fan_generic part_fan_t0]
pin = PA8
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[fan_generic part_fan_t1]
pin = PE5
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[heater_fan toolhead_cooling_fan_t0]
heater = extruder
shutdown_speed = 1
pin = toolboard_t0:PB4

[heater_fan toolhead_cooling_fan_t1]
heater = extruder1
shutdown_speed = 1
pin = toolboard_t1:PB4

[controller_fan controller_fan]
pin = dinghy:PA4
tachometer_pin = dinghy:PC15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[z_offset_probe]
pin = ^PG10
z_offset = -7
y_offset = 0
x_offset = 37.5
speed = 10
samples = 3
sample_retract_dist = 5
lift_speed = 10.0
samples_result = median
samples_tolerance = 0.2
samples_tolerance_retries = 5

[neopixel vaoc_led]
pin = PB10
chain_count = 6
color_order = GRB

[heater_fan vaoc_fan]
pin = PD13
heater = heater_bed
fan_speed = 1.0
heater_temp = 50

[fan_generic filter]
pin = !PD14
enable_pin = PD15

[gcode_macro T0]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = True
variable_color = "7bff33"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = -32.6
variable_parking_position = -57.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=0 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[gcode_macro T1]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = False
variable_color = "0ea5e9"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = 532.6
variable_parking_position = 557.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=1 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[save_variables]
filename = /home/pi/printer_data/config/ratos-variables.cfg

[mcu dinghy]
serial = /dev/serial/by-id/usb-Klipper_stm32f072xb_Dragon_dinghy-if00

[temperature_sensor th0]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA0

[temperature_sensor th1]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA1

[temperature_sensor th2]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA2

[temperature_sensor th3]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA3

[controller_fan CTL2]
pin = dinghy:PB14
tachometer_pin = dinghy:PB15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[mcu plasma]
serial = /dev/serial/by-id/usb-Klipper_rp2040_Plasma-if00

[neopixel Chamber_Lights]
pin = plasma:gpio15
chain_count = 140
color_order = GRBW
initial_red = 0.0
initial_green = 0.0
initial_blue = 0.0
initial_white = 0.1

[beacon model default]
model_coef = 1.5287863993594841,
	1.9289099639750602,
	0.8838828622507556,
	0.25554883784260735,
	-0.015171504024913506,
	0.3044946127013882,
	0.15820427856566457,
	-0.25262403959326246,
	0.042488512846660914,
	0.16662470122520964
model_domain = 1.842634574664148e-07,1.9339206373083917e-07
model_range = 0.200000,5.000000
model_temp = 13.222247
model_offset = 0.00000

[bed_mesh default]
version = 1
points = 
	0.016163, 0.016713, 0.001923, -0.017658, -0.031574, -0.032498, -0.030898, -0.032177, -0.035213, -0.031148, -0.021322, -0.016924, -0.015012, -0.013911, -0.012197, -0.012583, -0.010489, -0.007529, -0.003986, -0.000980, 0.005518, 0.014442, 0.027426, 0.034677, 0.037410, 0.040391, 0.041842, 0.040369, 0.037615, 0.030776, 0.027664, 0.022856, 0.016892, 0.015398, 0.014717, 0.006921, 0.001532, 0.000731, 0.008657, 0.014036
	0.005356, -0.005066, -0.016998, -0.029668, -0.038334, -0.043672, -0.041139, -0.042488, -0.045199, -0.039432, -0.028746, -0.023642, -0.024058, -0.022802, -0.019679, -0.018514, -0.018102, -0.016476, -0.012722, -0.010077, -0.001809, 0.007180, 0.019853, 0.027754, 0.029964, 0.033626, 0.036783, 0.032018, 0.029372, 0.020847, 0.017634, 0.011926, 0.009013, 0.009254, 0.007972, -0.001380, -0.006940, -0.002160, 0.006135, 0.008330
	-0.004900, -0.006720, -0.021914, -0.039691, -0.050459, -0.050377, -0.046281, -0.048755, -0.054708, -0.051499, -0.033927, -0.027632, -0.030243, -0.031447, -0.024387, -0.021408, -0.020382, -0.018068, -0.015930, -0.013877, -0.006099, 0.003479, 0.013310, 0.024783, 0.025522, 0.030849, 0.033573, 0.031409, 0.025495, 0.016683, 0.011264, 0.008805, 0.006856, 0.008059, 0.007305, 0.002581, -0.003320, -0.003239, 0.004691, 0.010045
	-0.008791, -0.019334, -0.029149, -0.040533, -0.051698, -0.058235, -0.054863, -0.054840, -0.055692, -0.049534, -0.036731, -0.033053, -0.035667, -0.035315, -0.024352, -0.023825, -0.022538, -0.020438, -0.018207, -0.015389, -0.006515, 0.001966, 0.013591, 0.019434, 0.020600, 0.024967, 0.029425, 0.026812, 0.018980, 0.007878, 0.002360, 0.000859, 0.003849, 0.005649, 0.005421, -0.000416, -0.007906, -0.003164, 0.007582, 0.010039
	-0.018512, -0.018210, -0.033932, -0.050501, -0.061588, -0.064139, -0.060236, -0.062528, -0.067065, -0.062039, -0.045815, -0.039448, -0.040521, -0.042080, -0.033870, -0.030878, -0.027396, -0.024548, -0.021298, -0.020041, -0.011880, -0.002847, 0.008689, 0.015857, 0.015934, 0.018697, 0.022439, 0.022106, 0.017916, 0.005879, 0.001037, -0.001311, -0.001335, 0.001897, 0.003656, 0.000561, -0.006084, -0.005683, 0.000338, 0.006245
	-0.028558, -0.036721, -0.044680, -0.054969, -0.066140, -0.075045, -0.073515, -0.073161, -0.075696, -0.068963, -0.058892, -0.053111, -0.050990, -0.048040, -0.041262, -0.037419, -0.034866, -0.031845, -0.029787, -0.026524, -0.017896, -0.009322, -0.001010, 0.005819, 0.008058, 0.010456, 0.013266, 0.012529, 0.007992, -0.001491, -0.006769, -0.009303, -0.005980, -0.003567, -0.003340, -0.011496, -0.018818, -0.014808, -0.004181, -0.000733
	-0.037253, -0.038393, -0.053129, -0.066170, -0.075959, -0.079233, -0.077475, -0.082688, -0.086779, -0.083983, -0.069005, -0.062542, -0.060351, -0.058481, -0.051101, -0.043149, -0.039837, -0.037039, -0.034698, -0.031301, -0.024330, -0.019786, -0.010285, -0.001967, 0.002812, 0.004899, 0.009657, 0.006946, 0.002155, -0.005232, -0.009851, -0.011218, -0.011509, -0.010097, -0.010293, -0.013175, -0.018958, -0.019846, -0.012107, -0.005641
	-0.046584, -0.055590, -0.062606, -0.069218, -0.080399, -0.087414, -0.089037, -0.092376, -0.095115, -0.088957, -0.080802, -0.073290, -0.068741, -0.064591, -0.054452, -0.048270, -0.045916, -0.044559, -0.042047, -0.039605, -0.032667, -0.025789, -0.019495, -0.012773, -0.006697, -0.003025, 0.001413, 0.000817, -0.004738, -0.013008, -0.017605, -0.018191, -0.018524, -0.016356, -0.016750, -0.021992, -0.028943, -0.025791, -0.016146, -0.010447
	-0.051029, -0.051677, -0.068218, -0.079622, -0.088590, -0.089331, -0.089731, -0.096072, -0.105329, -0.100771, -0.087584, -0.079320, -0.075489, -0.072081, -0.064183, -0.054662, -0.048601, -0.049465, -0.047050, -0.045011, -0.040009, -0.032508, -0.025212, -0.018144, -0.011996, -0.008136, -0.003187, -0.003214, -0.006646, -0.013044, -0.019446, -0.020615, -0.022270, -0.021298, -0.020215, -0.020946, -0.026034, -0.026598, -0.021025, -0.012328
	-0.057184, -0.064908, -0.073093, -0.081584, -0.091971, -0.097048, -0.097688, -0.101869, -0.106651, -0.102162, -0.095658, -0.087938, -0.082718, -0.077017, -0.069608, -0.060682, -0.056889, -0.056864, -0.054260, -0.052011, -0.044563, -0.038927, -0.031943, -0.025832, -0.021170, -0.014319, -0.009046, -0.008543, -0.011751, -0.020287, -0.026608, -0.027259, -0.029120, -0.025549, -0.023221, -0.027725, -0.032477, -0.028427, -0.019343, -0.014932
	-0.060411, -0.062241, -0.080781, -0.090744, -0.100903, -0.099702, -0.098468, -0.104236, -0.116853, -0.112701, -0.102623, -0.095036, -0.091407, -0.089871, -0.079701, -0.070222, -0.064325, -0.063875, -0.062248, -0.059396, -0.052699, -0.047589, -0.041526, -0.028442, -0.024526, -0.019549, -0.015403, -0.014251, -0.017989, -0.022824, -0.027328, -0.029155, -0.033315, -0.032426, -0.027619, -0.030776, -0.033688, -0.032458, -0.027219, -0.019649
	-0.067541, -0.076514, -0.082321, -0.088656, -0.099968, -0.104930, -0.105875, -0.109051, -0.115531, -0.112996, -0.105760, -0.100390, -0.096171, -0.090011, -0.080050, -0.073632, -0.067451, -0.067031, -0.065225, -0.062471, -0.056370, -0.050129, -0.041626, -0.030801, -0.027579, -0.022472, -0.014826, -0.015306, -0.020316, -0.025953, -0.030661, -0.034103, -0.035502, -0.032738, -0.031311, -0.037314, -0.041306, -0.035280, -0.027449, -0.020395
	-0.068162, -0.069269, -0.088235, -0.096809, -0.103385, -0.103271, -0.102507, -0.109535, -0.123412, -0.118580, -0.106622, -0.099580, -0.097644, -0.096978, -0.087259, -0.077196, -0.068978, -0.067016, -0.063682, -0.062548, -0.057901, -0.052295, -0.044088, -0.032703, -0.026551, -0.021607, -0.014155, -0.013747, -0.017390, -0.022419, -0.027444, -0.030877, -0.033450, -0.032423, -0.032041, -0.033598, -0.035149, -0.034054, -0.029356, -0.020998
	-0.069473, -0.075924, -0.083569, -0.089648, -0.101235, -0.105828, -0.109144, -0.112613, -0.117233, -0.114186, -0.107090, -0.098616, -0.097084, -0.094257, -0.086773, -0.076409, -0.069532, -0.066472, -0.060956, -0.059191, -0.052886, -0.047752, -0.041275, -0.032437, -0.027780, -0.020398, -0.012061, -0.010133, -0.014056, -0.021528, -0.027924, -0.030605, -0.030609, -0.026068, -0.029346, -0.033991, -0.038254, -0.030610, -0.021109, -0.015885
	-0.068084, -0.066409, -0.083944, -0.094013, -0.102504, -0.105274, -0.106036, -0.112090, -0.121664, -0.117824, -0.104850, -0.097467, -0.098833, -0.098622, -0.089603, -0.078147, -0.068143, -0.066300, -0.061573, -0.057727, -0.054825, -0.048625, -0.040164, -0.030532, -0.025948, -0.020264, -0.014196, -0.010702, -0.013794, -0.019775, -0.026095, -0.028838, -0.030254, -0.027944, -0.027980, -0.030915, -0.032446, -0.028861, -0.023732, -0.014676
	-0.065280, -0.068669, -0.076948, -0.082397, -0.094986, -0.105117, -0.107099, -0.108954, -0.112557, -0.110326, -0.100725, -0.096325, -0.096240, -0.092388, -0.081185, -0.071682, -0.065650, -0.062250, -0.057027, -0.054691, -0.048349, -0.042069, -0.032712, -0.027728, -0.023396, -0.018458, -0.008357, -0.005699, -0.011447, -0.020033, -0.026387, -0.030280, -0.028443, -0.023735, -0.023838, -0.031580, -0.034204, -0.027768, -0.018029, -0.010628
	-0.061662, -0.057052, -0.075163, -0.086710, -0.094182, -0.097544, -0.098814, -0.105908, -0.114460, -0.111718, -0.097559, -0.091614, -0.093860, -0.093098, -0.081687, -0.069410, -0.064117, -0.062745, -0.055603, -0.051413, -0.048043, -0.040363, -0.031842, -0.023420, -0.017470, -0.012600, -0.008163, -0.003898, -0.007635, -0.013254, -0.019807, -0.025153, -0.027074, -0.023513, -0.023727, -0.028669, -0.029153, -0.024831, -0.018735, -0.009246
	-0.056176, -0.059439, -0.066501, -0.071527, -0.085216, -0.094918, -0.097595, -0.099419, -0.101847, -0.102015, -0.093849, -0.089867, -0.088840, -0.083167, -0.071832, -0.062522, -0.058023, -0.057771, -0.053050, -0.048285, -0.041374, -0.033527, -0.024473, -0.018428, -0.013958, -0.008161, -0.001196, 0.001754, -0.004016, -0.011132, -0.018325, -0.021813, -0.021514, -0.016948, -0.018061, -0.025702, -0.028671, -0.021470, -0.011028, -0.001934
	-0.059202, -0.050525, -0.065461, -0.076792, -0.084156, -0.088538, -0.090719, -0.096070, -0.105729, -0.105136, -0.090350, -0.083865, -0.087807, -0.086145, -0.074773, -0.064235, -0.057641, -0.055896, -0.051286, -0.046566, -0.042431, -0.034723, -0.023762, -0.014983, -0.009126, -0.004877, 0.000094, 0.003492, -0.000931, -0.005883, -0.011665, -0.015251, -0.016432, -0.016119, -0.015373, -0.018827, -0.019994, -0.017564, -0.012298, 0.002094
	-0.055561, -0.058184, -0.062669, -0.068111, -0.080741, -0.091895, -0.093911, -0.094387, -0.100239, -0.100695, -0.089841, -0.085682, -0.085212, -0.082910, -0.073072, -0.063594, -0.056157, -0.053482, -0.048107, -0.045405, -0.039982, -0.029777, -0.019905, -0.013872, -0.009732, -0.004272, 0.003500, 0.006909, 0.001302, -0.004626, -0.012374, -0.014751, -0.014637, -0.011794, -0.012913, -0.018244, -0.023377, -0.018086, -0.006575, 0.003294
	-0.062834, -0.047300, -0.060870, -0.073023, -0.079303, -0.082121, -0.083623, -0.091321, -0.100996, -0.098896, -0.085406, -0.078881, -0.081932, -0.082077, -0.074409, -0.063158, -0.053822, -0.050328, -0.045077, -0.039678, -0.035825, -0.028532, -0.017793, -0.009121, -0.003444, -0.000905, 0.003990, 0.007745, 0.004595, 0.000143, -0.004555, -0.007411, -0.010850, -0.010100, -0.010079, -0.013177, -0.016434, -0.014663, -0.010248, -0.000213
	-0.054748, -0.053907, -0.057576, -0.063118, -0.072478, -0.081366, -0.084424, -0.086348, -0.089718, -0.089305, -0.081771, -0.076889, -0.076923, -0.073518, -0.067973, -0.057643, -0.050848, -0.046966, -0.041560, -0.036436, -0.029233, -0.020685, -0.010240, -0.004935, -0.001084, 0.002478, 0.009168, 0.014038, 0.010885, 0.004752, -0.001650, -0.004209, -0.003998, -0.002336, -0.003784, -0.010930, -0.016480, -0.012798, -0.003650, 0.002998
	-0.059345, -0.041989, -0.057435, -0.068229, -0.072857, -0.072586, -0.075155, -0.083286, -0.091292, -0.089727, -0.073702, -0.068353, -0.072910, -0.073863, -0.065527, -0.053635, -0.046064, -0.043899, -0.037607, -0.031251, -0.026194, -0.018885, -0.008095, 0.000309, 0.004911, 0.007046, 0.010642, 0.015635, 0.015277, 0.012612, 0.008074, 0.004852, 0.001546, 0.000504, 0.000589, -0.002769, -0.006432, -0.007765, -0.005391, 0.006950
	-0.050324, -0.049088, -0.052417, -0.057257, -0.063818, -0.071057, -0.074636, -0.075459, -0.079445, -0.077368, -0.068788, -0.063940, -0.065040, -0.063419, -0.054864, -0.044910, -0.038774, -0.036951, -0.031149, -0.026080, -0.018383, -0.011985, -0.001732, 0.003893, 0.007180, 0.011120, 0.017429, 0.021738, 0.019167, 0.015812, 0.011027, 0.007243, 0.006720, 0.009346, 0.006598, -0.003776, -0.009199, -0.007592, 0.005481, 0.014396
	-0.058437, -0.035937, -0.050762, -0.060425, -0.061123, -0.059090, -0.062399, -0.072124, -0.080338, -0.074950, -0.060985, -0.054754, -0.059333, -0.060500, -0.051714, -0.038834, -0.031117, -0.031693, -0.025186, -0.017982, -0.014316, -0.010137, 0.000228, 0.008774, 0.014018, 0.016470, 0.019918, 0.022071, 0.021109, 0.019957, 0.018698, 0.015803, 0.013135, 0.011136, 0.008719, 0.003522, -0.000994, 0.000525, 0.006297, 0.018454
	-0.046143, -0.041577, -0.045391, -0.046668, -0.051722, -0.057607, -0.062802, -0.065205, -0.068243, -0.066293, -0.058216, -0.051324, -0.051806, -0.051018, -0.043393, -0.032431, -0.024016, -0.023321, -0.018504, -0.013897, -0.008455, -0.001123, 0.006609, 0.010462, 0.013887, 0.019328, 0.024804, 0.026590, 0.023420, 0.020337, 0.017129, 0.017199, 0.016391, 0.015616, 0.013257, 0.005832, -0.000019, 0.003462, 0.014308, 0.023624
	-0.051989, -0.030294, -0.043380, -0.051339, -0.050711, -0.048193, -0.052258, -0.061218, -0.070507, -0.068810, -0.049476, -0.042352, -0.046018, -0.046673, -0.038670, -0.027263, -0.018137, -0.018587, -0.013603, -0.008482, -0.004647, -0.000011, 0.008230, 0.015652, 0.019436, 0.023069, 0.024762, 0.027750, 0.028115, 0.026227, 0.022220, 0.023166, 0.020341, 0.018455, 0.014918, 0.011932, 0.007138, 0.008523, 0.014718, 0.026201
	-0.041448, -0.035286, -0.036538, -0.037577, -0.044652, -0.049300, -0.051092, -0.052841, -0.058068, -0.056947, -0.046235, -0.038436, -0.037494, -0.034175, -0.028932, -0.016904, -0.010075, -0.010552, -0.004464, -0.001243, 0.003236, 0.010200, 0.015604, 0.020362, 0.023157, 0.028023, 0.032826, 0.035958, 0.034819, 0.030600, 0.025988, 0.026013, 0.026284, 0.025661, 0.022322, 0.013336, 0.006464, 0.011312, 0.022330, 0.031668
	-0.048540, -0.022534, -0.035260, -0.042156, -0.042749, -0.037408, -0.038818, -0.047322, -0.056808, -0.053643, -0.035691, -0.027822, -0.028789, -0.028255, -0.020274, -0.007285, -0.000723, -0.000788, 0.005440, 0.008938, 0.008953, 0.012074, 0.017957, 0.025241, 0.029175, 0.032057, 0.033733, 0.038359, 0.039349, 0.037161, 0.034052, 0.034585, 0.032020, 0.029940, 0.026326, 0.024577, 0.020432, 0.021586, 0.024568, 0.034552
	-0.033086, -0.027982, -0.029443, -0.029011, -0.035629, -0.040579, -0.038290, -0.037389, -0.041260, -0.040430, -0.032279, -0.021394, -0.018817, -0.015525, -0.007558, 0.006345, 0.011048, 0.011271, 0.013497, 0.017030, 0.017449, 0.022752, 0.026764, 0.030722, 0.033532, 0.037203, 0.043356, 0.048536, 0.047776, 0.043851, 0.039311, 0.039944, 0.039954, 0.038931, 0.034893, 0.030946, 0.023127, 0.027359, 0.034859, 0.043920
	-0.036218, -0.016846, -0.030897, -0.036980, -0.037261, -0.033334, -0.030888, -0.034074, -0.042142, -0.039980, -0.021377, -0.013603, -0.014171, -0.013131, -0.001768, 0.014998, 0.020060, 0.018173, 0.019934, 0.024704, 0.023739, 0.024617, 0.027288, 0.035116, 0.041187, 0.043128, 0.045921, 0.051709, 0.053031, 0.050698, 0.047697, 0.047728, 0.046845, 0.043201, 0.041805, 0.040728, 0.036184, 0.034435, 0.035120, 0.045329
	-0.029808, -0.023871, -0.026541, -0.026705, -0.031203, -0.036908, -0.034411, -0.029231, -0.028090, -0.026102, -0.016691, -0.007747, -0.004471, 0.001560, 0.010738, 0.025062, 0.027672, 0.024833, 0.026976, 0.029502, 0.030754, 0.035709, 0.039403, 0.044719, 0.046379, 0.049250, 0.054178, 0.059793, 0.059542, 0.052111, 0.047608, 0.050103, 0.053142, 0.052747, 0.050045, 0.044102, 0.033149, 0.035392, 0.045678, 0.054080
	-0.032238, -0.008993, -0.023999, -0.030969, -0.028658, -0.024887, -0.024493, -0.028088, -0.031053, -0.022849, -0.003868, 0.004647, 0.004540, 0.007560, 0.018373, 0.031401, 0.035778, 0.033768, 0.035173, 0.035884, 0.036597, 0.038940, 0.044566, 0.053914, 0.056554, 0.056382, 0.056449, 0.060387, 0.062696, 0.058223, 0.055016, 0.056193, 0.056891, 0.052793, 0.052741, 0.052626, 0.048117, 0.045032, 0.048033, 0.055100
	-0.019758, -0.015110, -0.017814, -0.018871, -0.023340, -0.028653, -0.026880, -0.018681, -0.017020, -0.011343, -0.001002, 0.008249, 0.014012, 0.020367, 0.026878, 0.038534, 0.041827, 0.039532, 0.039775, 0.039109, 0.043172, 0.049325, 0.056604, 0.059583, 0.059329, 0.059876, 0.062766, 0.068759, 0.067214, 0.059657, 0.055950, 0.056798, 0.058619, 0.058591, 0.059849, 0.056473, 0.046841, 0.047921, 0.058342, 0.065346
	-0.018628, -0.000296, -0.014764, -0.022634, -0.020483, -0.016362, -0.015485, -0.017352, -0.020246, -0.010362, 0.008635, 0.018414, 0.018542, 0.024258, 0.033370, 0.045728, 0.049983, 0.044610, 0.044638, 0.047649, 0.049220, 0.051954, 0.058932, 0.065915, 0.069102, 0.067410, 0.067680, 0.073734, 0.072203, 0.067293, 0.063945, 0.064378, 0.065047, 0.061989, 0.062882, 0.063468, 0.059707, 0.057986, 0.059739, 0.066139
	-0.010091, -0.006551, -0.008018, -0.009589, -0.016068, -0.020662, -0.019451, -0.010985, -0.009391, -0.003580, 0.007826, 0.019598, 0.024961, 0.033762, 0.040618, 0.050868, 0.052139, 0.050495, 0.049198, 0.051777, 0.056840, 0.061771, 0.068414, 0.072295, 0.073443, 0.072145, 0.073414, 0.079338, 0.075988, 0.067367, 0.064745, 0.064435, 0.066982, 0.065811, 0.067424, 0.063230, 0.058438, 0.059982, 0.067672, 0.072460
	-0.016254, 0.006291, -0.008031, -0.013944, -0.014475, -0.010741, -0.009932, -0.011709, -0.015503, -0.006971, 0.013190, 0.024865, 0.029121, 0.033942, 0.044335, 0.054572, 0.058078, 0.055224, 0.055897, 0.058327, 0.061207, 0.063939, 0.070506, 0.078141, 0.084203, 0.081223, 0.079519, 0.082883, 0.080890, 0.076174, 0.071279, 0.073064, 0.071225, 0.066859, 0.069860, 0.070836, 0.069427, 0.069140, 0.070950, 0.075269
	-0.008127, 0.000730, 0.001164, -0.000308, -0.006659, -0.012343, -0.011463, -0.003755, -0.001876, 0.005166, 0.016616, 0.030243, 0.036509, 0.045020, 0.053681, 0.063738, 0.066425, 0.063964, 0.062796, 0.065633, 0.071912, 0.077280, 0.082580, 0.086477, 0.089798, 0.089603, 0.091453, 0.096125, 0.088708, 0.079903, 0.074317, 0.076190, 0.075399, 0.075242, 0.079628, 0.077855, 0.071473, 0.073702, 0.082757, 0.088086
	-0.010951, 0.013218, -0.000878, -0.006241, -0.005623, 0.000046, 0.000158, -0.002943, -0.005314, 0.005491, 0.026890, 0.035754, 0.041490, 0.045829, 0.059325, 0.070249, 0.074114, 0.071815, 0.073229, 0.076313, 0.080778, 0.081554, 0.087919, 0.096206, 0.101562, 0.101674, 0.100494, 0.103989, 0.100292, 0.093977, 0.088080, 0.088136, 0.086555, 0.081494, 0.084966, 0.087073, 0.084113, 0.085184, 0.087700, 0.092188
	-0.002972, 0.006020, 0.006098, 0.004303, 0.001326, -0.002386, -0.001840, 0.005325, 0.008624, 0.016246, 0.026781, 0.039696, 0.048540, 0.055938, 0.066982, 0.076497, 0.080828, 0.079669, 0.080127, 0.083754, 0.089783, 0.093456, 0.100570, 0.105322, 0.107132, 0.110571, 0.113141, 0.118064, 0.111721, 0.101634, 0.093555, 0.093112, 0.093104, 0.092325, 0.094780, 0.092552, 0.085283, 0.088882, 0.097508, 0.105280
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 11.4
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Preperations]
version = 1
points = 
	0.012158, -0.006098, -0.020628, -0.034069, -0.049418, -0.058491, -0.062706, -0.063181, -0.065552, -0.063461, -0.057373, -0.056717, -0.056579, -0.054080, -0.053373, -0.056878, -0.057281, -0.055224, -0.049676, -0.047605, -0.041454, -0.034605, -0.022490, -0.011292, -0.009411, -0.005344, -0.003510, -0.002717, -0.005999, -0.010712, -0.013141, -0.015611, -0.020004, -0.017667, -0.016629, -0.022248, -0.024864, -0.024065, -0.014921, -0.010826
	-0.005958, -0.021084, -0.033800, -0.047903, -0.059950, -0.071345, -0.072502, -0.073350, -0.075852, -0.072963, -0.067236, -0.064315, -0.065698, -0.064338, -0.062871, -0.065238, -0.067095, -0.063584, -0.059241, -0.057846, -0.051380, -0.043157, -0.030230, -0.019950, -0.018121, -0.014291, -0.009354, -0.013065, -0.016464, -0.022925, -0.025337, -0.026541, -0.030577, -0.029068, -0.027094, -0.030532, -0.034241, -0.032625, -0.021498, -0.020513
	-0.017526, -0.027763, -0.040710, -0.055305, -0.068172, -0.079641, -0.081247, -0.081903, -0.083679, -0.081855, -0.073270, -0.070340, -0.072083, -0.071536, -0.066055, -0.065901, -0.069085, -0.066531, -0.063284, -0.061616, -0.053366, -0.047292, -0.035451, -0.023167, -0.022205, -0.016699, -0.012552, -0.014153, -0.018802, -0.030443, -0.032210, -0.034051, -0.034437, -0.031439, -0.030406, -0.032817, -0.036351, -0.034849, -0.024250, -0.019489
	-0.017750, -0.030284, -0.043463, -0.055839, -0.071865, -0.084888, -0.086157, -0.084619, -0.086681, -0.084515, -0.075246, -0.073263, -0.075604, -0.075123, -0.069177, -0.070723, -0.071097, -0.068644, -0.065465, -0.063718, -0.057574, -0.049335, -0.036556, -0.028418, -0.028259, -0.023387, -0.018454, -0.020519, -0.027499, -0.038314, -0.041534, -0.041886, -0.039972, -0.036438, -0.033959, -0.033009, -0.038291, -0.036339, -0.022688, -0.024783
	-0.021354, -0.034103, -0.047541, -0.060551, -0.075691, -0.089373, -0.092241, -0.091621, -0.093203, -0.090723, -0.082480, -0.079781, -0.079706, -0.079674, -0.074365, -0.073780, -0.073465, -0.070165, -0.064970, -0.065503, -0.059104, -0.051038, -0.041817, -0.031243, -0.031386, -0.028837, -0.023658, -0.024237, -0.029641, -0.039210, -0.042766, -0.044461, -0.041863, -0.039075, -0.034881, -0.034571, -0.039386, -0.038253, -0.031659, -0.024202
	-0.027696, -0.041184, -0.054054, -0.064759, -0.080898, -0.094964, -0.097906, -0.098033, -0.101256, -0.098300, -0.091517, -0.088420, -0.086945, -0.085220, -0.079938, -0.079979, -0.079828, -0.074842, -0.072903, -0.072415, -0.065384, -0.057454, -0.048482, -0.040977, -0.039336, -0.036065, -0.032553, -0.034336, -0.039337, -0.046271, -0.049398, -0.051220, -0.049530, -0.045000, -0.045029, -0.042100, -0.049767, -0.046386, -0.035574, -0.032188
	-0.033426, -0.046259, -0.059363, -0.068024, -0.084858, -0.097009, -0.103434, -0.106215, -0.107319, -0.106178, -0.100333, -0.097536, -0.095352, -0.091322, -0.086332, -0.082309, -0.081440, -0.078413, -0.075067, -0.073134, -0.068255, -0.062667, -0.054300, -0.046004, -0.042001, -0.039181, -0.035010, -0.036092, -0.041599, -0.048788, -0.051751, -0.051179, -0.051019, -0.049121, -0.045860, -0.046756, -0.050005, -0.051613, -0.040237, -0.035349
	-0.037931, -0.051993, -0.066455, -0.075044, -0.088177, -0.102890, -0.108223, -0.112373, -0.115787, -0.113421, -0.108543, -0.105936, -0.101048, -0.096863, -0.090726, -0.087882, -0.086665, -0.083874, -0.081096, -0.080894, -0.075125, -0.071038, -0.063072, -0.054696, -0.051039, -0.046728, -0.042566, -0.043887, -0.048745, -0.056834, -0.059808, -0.060521, -0.060664, -0.057968, -0.056317, -0.052477, -0.058814, -0.055877, -0.046325, -0.042545
	-0.041429, -0.053634, -0.067633, -0.077111, -0.090998, -0.103561, -0.109445, -0.114741, -0.120075, -0.119821, -0.114703, -0.110411, -0.105589, -0.099826, -0.093730, -0.089705, -0.087199, -0.086439, -0.082688, -0.082221, -0.078348, -0.073203, -0.065273, -0.058731, -0.054025, -0.049231, -0.044830, -0.043830, -0.045839, -0.054137, -0.059075, -0.059515, -0.058546, -0.056956, -0.054145, -0.053129, -0.056587, -0.056341, -0.047057, -0.039936
	-0.044295, -0.058972, -0.072101, -0.082726, -0.095001, -0.106449, -0.111505, -0.118363, -0.124608, -0.123506, -0.120263, -0.115400, -0.110227, -0.104535, -0.100348, -0.095757, -0.092961, -0.092377, -0.089613, -0.088047, -0.084834, -0.079314, -0.072500, -0.064519, -0.060449, -0.055767, -0.051803, -0.050997, -0.052855, -0.058115, -0.063348, -0.065363, -0.067936, -0.063474, -0.061475, -0.054726, -0.062529, -0.055352, -0.048878, -0.044991
	-0.045804, -0.056574, -0.073308, -0.082450, -0.097495, -0.107467, -0.111501, -0.116418, -0.126724, -0.125980, -0.123231, -0.120494, -0.114667, -0.111289, -0.103451, -0.099228, -0.095880, -0.095882, -0.093328, -0.091000, -0.087051, -0.081909, -0.075949, -0.064971, -0.061050, -0.055137, -0.049046, -0.047319, -0.049806, -0.056968, -0.059608, -0.060249, -0.063032, -0.060556, -0.056284, -0.056263, -0.058891, -0.057890, -0.051554, -0.042382
	-0.049818, -0.062681, -0.076305, -0.084328, -0.098717, -0.107866, -0.113937, -0.120088, -0.128622, -0.128931, -0.126353, -0.123191, -0.118529, -0.115642, -0.106288, -0.103976, -0.099708, -0.097750, -0.094501, -0.094545, -0.090910, -0.085952, -0.077352, -0.067196, -0.062435, -0.057738, -0.052934, -0.051098, -0.055294, -0.061112, -0.063120, -0.067525, -0.067979, -0.066558, -0.064608, -0.060597, -0.067812, -0.057641, -0.056224, -0.046471
	-0.050591, -0.060432, -0.075602, -0.083877, -0.096933, -0.106147, -0.112334, -0.118295, -0.127966, -0.128757, -0.125157, -0.121831, -0.118557, -0.116124, -0.108723, -0.104502, -0.099469, -0.095841, -0.090662, -0.089822, -0.087969, -0.084545, -0.076375, -0.064821, -0.059093, -0.053427, -0.047372, -0.044341, -0.047964, -0.054064, -0.057133, -0.059152, -0.061568, -0.059109, -0.056640, -0.056691, -0.056844, -0.054564, -0.048514, -0.040641
	-0.047704, -0.059564, -0.073127, -0.080945, -0.093764, -0.105483, -0.111501, -0.118792, -0.124812, -0.126576, -0.122064, -0.118087, -0.116126, -0.114867, -0.108053, -0.103336, -0.097558, -0.093250, -0.086537, -0.085303, -0.083677, -0.079292, -0.070542, -0.062526, -0.056818, -0.052534, -0.044035, -0.041353, -0.046942, -0.051329, -0.055481, -0.062777, -0.058499, -0.058025, -0.057390, -0.053562, -0.060843, -0.046555, -0.046260, -0.036083
	-0.046496, -0.052983, -0.067518, -0.076904, -0.091704, -0.103105, -0.111995, -0.117751, -0.122307, -0.122941, -0.118230, -0.115004, -0.114258, -0.113138, -0.105515, -0.098417, -0.093384, -0.090070, -0.083281, -0.079846, -0.078725, -0.075452, -0.066225, -0.057269, -0.053103, -0.047808, -0.039772, -0.036834, -0.041270, -0.047376, -0.051111, -0.053848, -0.053029, -0.050301, -0.048919, -0.050775, -0.050121, -0.046842, -0.039633, -0.030497
	-0.040695, -0.051685, -0.064038, -0.070974, -0.086679, -0.101773, -0.109889, -0.114373, -0.117883, -0.118764, -0.113125, -0.110931, -0.111099, -0.109664, -0.098733, -0.093182, -0.090154, -0.086213, -0.077214, -0.077108, -0.075555, -0.069117, -0.060704, -0.054093, -0.049253, -0.044799, -0.037536, -0.035304, -0.040134, -0.045456, -0.051720, -0.056675, -0.053743, -0.052923, -0.049701, -0.050238, -0.056776, -0.041485, -0.041755, -0.027329
	-0.039842, -0.039428, -0.055732, -0.063890, -0.079179, -0.092823, -0.101698, -0.106156, -0.111709, -0.113152, -0.108033, -0.104872, -0.105645, -0.103501, -0.094487, -0.087264, -0.084273, -0.080950, -0.074116, -0.070973, -0.068409, -0.062825, -0.054757, -0.044150, -0.040620, -0.036602, -0.031538, -0.026478, -0.031123, -0.037600, -0.042341, -0.046700, -0.047380, -0.042880, -0.040967, -0.045367, -0.044192, -0.038553, -0.029948, -0.020790
	-0.030596, -0.038279, -0.051528, -0.058981, -0.073983, -0.089044, -0.099173, -0.101740, -0.104830, -0.107083, -0.102306, -0.101554, -0.101336, -0.097146, -0.089217, -0.083800, -0.080621, -0.078071, -0.071535, -0.068328, -0.065806, -0.056882, -0.048683, -0.039756, -0.036349, -0.031328, -0.025351, -0.024133, -0.029773, -0.033858, -0.040011, -0.044146, -0.043900, -0.044797, -0.038019, -0.042319, -0.047297, -0.031851, -0.034318, -0.013527
	-0.032121, -0.034722, -0.047839, -0.054710, -0.069175, -0.084213, -0.094533, -0.097233, -0.100863, -0.104775, -0.099781, -0.097416, -0.098804, -0.096059, -0.086694, -0.079692, -0.076749, -0.074609, -0.068106, -0.063906, -0.061136, -0.055447, -0.045559, -0.035389, -0.029696, -0.025708, -0.020034, -0.017335, -0.022665, -0.028532, -0.032369, -0.035760, -0.037212, -0.035201, -0.032872, -0.034132, -0.035907, -0.032127, -0.025026, -0.009282
	-0.026707, -0.034374, -0.045183, -0.052691, -0.067014, -0.084964, -0.092286, -0.094441, -0.099291, -0.103609, -0.098278, -0.094972, -0.097169, -0.095394, -0.086653, -0.080205, -0.076284, -0.070594, -0.064535, -0.062012, -0.060174, -0.051216, -0.040622, -0.033396, -0.029636, -0.024235, -0.017274, -0.018232, -0.021459, -0.024778, -0.031754, -0.034481, -0.033398, -0.037949, -0.030432, -0.033219, -0.038432, -0.021975, -0.030052, -0.009295
	-0.028559, -0.029280, -0.042071, -0.048655, -0.061603, -0.076257, -0.086817, -0.091815, -0.095682, -0.098682, -0.093729, -0.091168, -0.092213, -0.090073, -0.084070, -0.077048, -0.072045, -0.066267, -0.060309, -0.053639, -0.051696, -0.046852, -0.034069, -0.025602, -0.020640, -0.018021, -0.013180, -0.009049, -0.013846, -0.018012, -0.021061, -0.024515, -0.027068, -0.026804, -0.024283, -0.025595, -0.028234, -0.025272, -0.019246, -0.008595
	-0.025711, -0.029003, -0.038836, -0.048015, -0.058511, -0.074480, -0.083738, -0.087945, -0.091439, -0.094310, -0.090288, -0.087858, -0.088589, -0.086163, -0.081829, -0.075146, -0.071136, -0.064399, -0.057338, -0.052103, -0.049650, -0.043210, -0.032998, -0.023124, -0.020191, -0.016625, -0.012433, -0.010465, -0.009871, -0.015007, -0.021217, -0.021582, -0.023800, -0.027652, -0.021527, -0.027137, -0.030828, -0.020152, -0.026202, -0.008568
	-0.031287, -0.022523, -0.035800, -0.041583, -0.052691, -0.065901, -0.075941, -0.079246, -0.083936, -0.086778, -0.082235, -0.078893, -0.080642, -0.079419, -0.074324, -0.067418, -0.062113, -0.057744, -0.049923, -0.043390, -0.040055, -0.035512, -0.023838, -0.015485, -0.009895, -0.008346, -0.005387, 0.001467, -0.000104, -0.003777, -0.007926, -0.012023, -0.013970, -0.014207, -0.013994, -0.017009, -0.019233, -0.019282, -0.014210, -0.001146
	-0.020719, -0.024043, -0.035160, -0.041635, -0.051902, -0.063884, -0.072884, -0.076738, -0.081856, -0.083761, -0.077857, -0.074651, -0.077952, -0.076310, -0.069721, -0.063240, -0.056775, -0.055188, -0.046711, -0.042996, -0.039499, -0.032268, -0.023129, -0.015735, -0.012305, -0.009383, -0.005789, -0.001996, -0.001166, -0.005106, -0.009634, -0.009864, -0.011905, -0.015913, -0.010246, -0.016645, -0.022975, -0.011972, -0.018524, 0.001048
	-0.026050, -0.019774, -0.032555, -0.037813, -0.044657, -0.054435, -0.065271, -0.071019, -0.075585, -0.077479, -0.072635, -0.069526, -0.071046, -0.070770, -0.063085, -0.055960, -0.050956, -0.049593, -0.042773, -0.034996, -0.032645, -0.029030, -0.020343, -0.011008, -0.005751, -0.003252, 0.000746, 0.003215, 0.001749, -0.000068, -0.001413, -0.002608, -0.005837, -0.007103, -0.008431, -0.012027, -0.015656, -0.014417, -0.006321, 0.003748
	-0.021728, -0.019178, -0.031232, -0.036249, -0.042206, -0.053190, -0.064017, -0.068545, -0.074597, -0.074544, -0.069543, -0.065779, -0.067928, -0.067354, -0.060655, -0.052790, -0.047723, -0.046044, -0.038188, -0.034539, -0.032080, -0.027152, -0.018902, -0.012508, -0.009304, -0.003955, -0.000288, -0.001549, -0.000556, -0.003756, -0.008467, -0.003851, -0.005999, -0.012959, -0.007423, -0.015332, -0.017388, -0.005695, -0.010807, 0.007710
	-0.028204, -0.017096, -0.027984, -0.032129, -0.038374, -0.046561, -0.059356, -0.061847, -0.069228, -0.070551, -0.065474, -0.059719, -0.059893, -0.060271, -0.053666, -0.047202, -0.041189, -0.039979, -0.033189, -0.028761, -0.025714, -0.021660, -0.014905, -0.007841, -0.004669, -0.001174, 0.001874, 0.005613, 0.005527, 0.001504, -0.000694, 0.001892, 0.001885, -0.002506, -0.005619, -0.007166, -0.009935, -0.007406, 0.000545, 0.009983
	-0.019393, -0.017785, -0.025482, -0.028146, -0.036861, -0.047528, -0.055696, -0.059118, -0.064151, -0.066346, -0.060565, -0.055661, -0.055495, -0.051944, -0.048147, -0.040645, -0.036359, -0.035990, -0.026764, -0.024843, -0.023572, -0.019648, -0.013807, -0.006811, -0.004589, -0.000266, 0.003010, 0.004931, 0.006834, 0.003254, -0.001690, 0.003120, 0.001036, -0.005283, 0.000659, -0.007399, -0.010996, -0.000832, -0.006381, 0.012135
	-0.021519, -0.010062, -0.018662, -0.023011, -0.029067, -0.036961, -0.043194, -0.048197, -0.053632, -0.055489, -0.050054, -0.045247, -0.042655, -0.040243, -0.034315, -0.027094, -0.022697, -0.021644, -0.015333, -0.010768, -0.013712, -0.012051, -0.005326, 0.000560, 0.005300, 0.007429, 0.009930, 0.015968, 0.016454, 0.012383, 0.010385, 0.011612, 0.011413, 0.008357, 0.006831, 0.005524, 0.003087, 0.003507, 0.009876, 0.018892
	-0.017331, -0.015238, -0.021971, -0.024651, -0.029507, -0.040209, -0.044232, -0.046101, -0.052689, -0.053151, -0.047133, -0.042985, -0.040475, -0.037020, -0.029999, -0.021348, -0.018232, -0.017876, -0.013058, -0.008535, -0.013279, -0.011527, -0.006296, -0.001615, 0.002270, 0.006991, 0.010272, 0.013407, 0.015950, 0.012503, 0.008026, 0.013701, 0.011513, 0.004867, 0.010667, 0.006774, 0.003571, 0.012416, 0.004875, 0.020961
	-0.022637, -0.011107, -0.018340, -0.023896, -0.028320, -0.038092, -0.041212, -0.041642, -0.044537, -0.046015, -0.041699, -0.035805, -0.033527, -0.030911, -0.022925, -0.010175, -0.007279, -0.008644, -0.005065, -0.000597, -0.003797, -0.004052, 0.000635, 0.006175, 0.010857, 0.012993, 0.016956, 0.022765, 0.023298, 0.020262, 0.018285, 0.019467, 0.021161, 0.018785, 0.017891, 0.017817, 0.013874, 0.012825, 0.015904, 0.025844
	-0.014532, -0.010189, -0.019385, -0.022584, -0.028159, -0.037803, -0.040566, -0.038125, -0.040339, -0.038899, -0.033171, -0.028143, -0.025641, -0.019755, -0.012463, -0.003824, -0.000871, -0.002698, -0.000197, 0.001952, -0.001353, -0.000188, 0.004902, 0.012600, 0.014373, 0.016449, 0.018872, 0.022822, 0.026385, 0.020681, 0.015275, 0.021387, 0.023535, 0.016733, 0.022161, 0.018819, 0.011276, 0.020785, 0.014683, 0.032409
	-0.016972, -0.004835, -0.015539, -0.019706, -0.022971, -0.032222, -0.037732, -0.035551, -0.033892, -0.031679, -0.024624, -0.019946, -0.016412, -0.010040, -0.003445, 0.005991, 0.008364, 0.006410, 0.008289, 0.009260, 0.007409, 0.008691, 0.015230, 0.022729, 0.025465, 0.025502, 0.026102, 0.030309, 0.031861, 0.026963, 0.024651, 0.027000, 0.029039, 0.025577, 0.027217, 0.027660, 0.023245, 0.021705, 0.026383, 0.034120
	-0.007042, -0.003943, -0.013314, -0.016082, -0.020497, -0.030911, -0.035096, -0.030889, -0.029351, -0.025337, -0.018980, -0.012449, -0.008879, -0.001902, 0.003577, 0.011256, 0.012460, 0.010502, 0.011904, 0.011483, 0.010067, 0.013356, 0.020792, 0.027368, 0.026382, 0.028554, 0.028164, 0.029993, 0.033232, 0.028830, 0.022354, 0.027991, 0.029607, 0.020011, 0.031066, 0.031755, 0.025061, 0.037228, 0.024607, 0.041453
	-0.012463, -0.000987, -0.008994, -0.014815, -0.017487, -0.026372, -0.031392, -0.028459, -0.025402, -0.024153, -0.015566, -0.007862, -0.004579, 0.001484, 0.010757, 0.017401, 0.019536, 0.016264, 0.016278, 0.018231, 0.018193, 0.018217, 0.025442, 0.034794, 0.036179, 0.034770, 0.033985, 0.040104, 0.040404, 0.034161, 0.030977, 0.032380, 0.034144, 0.031909, 0.033231, 0.035957, 0.034171, 0.033050, 0.038776, 0.042972
	-0.002758, 0.000700, -0.008467, -0.011525, -0.018705, -0.027522, -0.031609, -0.027494, -0.026315, -0.023221, -0.014164, -0.006562, -0.002205, 0.006453, 0.013689, 0.018647, 0.017673, 0.016751, 0.017380, 0.018782, 0.019038, 0.021992, 0.027475, 0.034748, 0.036870, 0.036635, 0.035394, 0.037519, 0.038008, 0.032063, 0.025834, 0.030409, 0.033142, 0.023991, 0.034882, 0.034323, 0.030317, 0.042711, 0.030793, 0.045129
	-0.011501, 0.004979, -0.003199, -0.009532, -0.013737, -0.022490, -0.028056, -0.025047, -0.023987, -0.021727, -0.011113, -0.003633, 0.003070, 0.010580, 0.020230, 0.025058, 0.026653, 0.024592, 0.024567, 0.025613, 0.027386, 0.029282, 0.037705, 0.042901, 0.046601, 0.045443, 0.044217, 0.048155, 0.045715, 0.039788, 0.034981, 0.038594, 0.038594, 0.034532, 0.038671, 0.042065, 0.040659, 0.042101, 0.045919, 0.050030
	-0.005239, 0.006624, -0.001837, -0.005350, -0.012024, -0.022230, -0.026144, -0.022704, -0.021559, -0.017450, -0.008515, 0.000433, 0.007392, 0.014546, 0.023538, 0.029043, 0.029892, 0.027280, 0.028785, 0.030662, 0.032758, 0.032649, 0.040035, 0.046372, 0.048654, 0.050330, 0.049538, 0.049746, 0.048851, 0.041068, 0.034598, 0.041375, 0.041379, 0.030621, 0.043091, 0.044712, 0.038634, 0.053475, 0.042814, 0.059369
	-0.011843, 0.005417, 0.000007, -0.005709, -0.011391, -0.019100, -0.024151, -0.021274, -0.019356, -0.016953, -0.004422, 0.002891, 0.010688, 0.018353, 0.027665, 0.035281, 0.036655, 0.034937, 0.036795, 0.039994, 0.042705, 0.042668, 0.048600, 0.055673, 0.059602, 0.061002, 0.059934, 0.064283, 0.061835, 0.052838, 0.048644, 0.048401, 0.048158, 0.044262, 0.049173, 0.053313, 0.050054, 0.051718, 0.058112, 0.062677
	-0.003249, 0.007140, -0.000190, -0.005182, -0.010664, -0.017472, -0.021072, -0.018928, -0.015929, -0.011810, -0.001170, 0.006999, 0.014346, 0.022026, 0.033087, 0.037703, 0.039304, 0.038986, 0.040531, 0.042739, 0.044912, 0.045850, 0.052980, 0.060894, 0.062495, 0.065477, 0.066306, 0.069035, 0.066301, 0.058359, 0.048879, 0.054660, 0.053906, 0.042834, 0.051292, 0.054304, 0.049390, 0.064968, 0.053062, 0.067337
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 80.0
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Peperations]
version = 1
points = 
	0.022498, 0.020830, 0.014175, -0.000111, -0.007965, -0.011932, -0.009252, -0.003320, -0.000118, 0.004151, 0.015991, 0.024593, 0.030148, 0.034696, 0.042241, 0.043592, 0.045307, 0.051419, 0.057700, 0.066468, 0.072764, 0.085492, 0.100446, 0.113063, 0.118900, 0.122870, 0.130290, 0.129755, 0.129462, 0.124089, 0.122420, 0.123461, 0.116841, 0.117893, 0.119241, 0.115227, 0.110631, 0.109920, 0.117187, 0.124332
	0.004953, 0.000716, -0.005511, -0.010742, -0.018400, -0.024021, -0.019665, -0.013525, -0.009878, -0.004126, 0.008939, 0.016408, 0.019292, 0.023840, 0.033007, 0.033600, 0.034448, 0.041047, 0.049029, 0.052882, 0.062512, 0.072410, 0.089182, 0.103027, 0.106205, 0.110789, 0.117912, 0.115269, 0.112784, 0.106051, 0.103603, 0.104209, 0.099603, 0.105100, 0.101466, 0.099610, 0.095780, 0.096420, 0.108661, 0.108286
	-0.007933, -0.002801, -0.011350, -0.022484, -0.029473, -0.033231, -0.030354, -0.021826, -0.018408, -0.013209, 0.001640, 0.008984, 0.012027, 0.014149, 0.024334, 0.028649, 0.030597, 0.034667, 0.041223, 0.046241, 0.051968, 0.062511, 0.079099, 0.090699, 0.097837, 0.101667, 0.108218, 0.106595, 0.104490, 0.095444, 0.089512, 0.089259, 0.089179, 0.091741, 0.094161, 0.094254, 0.091002, 0.088753, 0.095405, 0.102343
	-0.010759, -0.012564, -0.018170, -0.023960, -0.033106, -0.040910, -0.038354, -0.031441, -0.026122, -0.019953, -0.006267, 0.000733, 0.002678, 0.006102, 0.015437, 0.019860, 0.022689, 0.029563, 0.035629, 0.037302, 0.045089, 0.055137, 0.070820, 0.082978, 0.087158, 0.088614, 0.094487, 0.093851, 0.091038, 0.080923, 0.074433, 0.073797, 0.073058, 0.081788, 0.080734, 0.083111, 0.078149, 0.079373, 0.091335, 0.087853
	-0.027313, -0.019238, -0.027920, -0.036645, -0.043223, -0.049872, -0.048503, -0.043853, -0.040737, -0.035179, -0.021622, -0.013493, -0.010171, -0.007317, 0.001347, 0.007440, 0.011360, 0.015985, 0.023916, 0.026329, 0.031680, 0.042865, 0.056754, 0.067621, 0.072919, 0.075964, 0.080156, 0.081233, 0.077771, 0.068443, 0.063939, 0.062251, 0.063828, 0.065094, 0.069498, 0.071735, 0.067423, 0.064065, 0.069162, 0.076272
	-0.033298, -0.035618, -0.039940, -0.043358, -0.050731, -0.061413, -0.060545, -0.055944, -0.052261, -0.045471, -0.035624, -0.027633, -0.021472, -0.017300, -0.006949, -0.002776, -0.000154, 0.006413, 0.012882, 0.014721, 0.023411, 0.031711, 0.040565, 0.054702, 0.058761, 0.061734, 0.065369, 0.066037, 0.061059, 0.053849, 0.049600, 0.048373, 0.049189, 0.054631, 0.050470, 0.056349, 0.047074, 0.049651, 0.057444, 0.057485
	-0.046284, -0.039039, -0.049010, -0.054961, -0.061001, -0.068408, -0.069602, -0.066474, -0.063117, -0.059357, -0.049570, -0.041166, -0.035441, -0.029269, -0.019658, -0.012395, -0.008906, -0.005538, 0.002012, 0.008339, 0.013216, 0.018793, 0.031185, 0.040165, 0.047175, 0.050605, 0.054283, 0.054442, 0.049166, 0.043483, 0.039000, 0.040758, 0.040857, 0.040759, 0.042263, 0.043438, 0.040051, 0.035886, 0.041332, 0.048851
	-0.049893, -0.051919, -0.058103, -0.060142, -0.067656, -0.077159, -0.079195, -0.078019, -0.075421, -0.069471, -0.060409, -0.054194, -0.044226, -0.037275, -0.027912, -0.020020, -0.016789, -0.012491, -0.003457, 0.001129, 0.004540, 0.009435, 0.018232, 0.027941, 0.035138, 0.038227, 0.042656, 0.044103, 0.038517, 0.032121, 0.029666, 0.027319, 0.029774, 0.031572, 0.028887, 0.034828, 0.023795, 0.030023, 0.033606, 0.036047
	-0.061015, -0.055279, -0.067497, -0.072234, -0.078637, -0.083600, -0.085954, -0.087271, -0.088647, -0.083447, -0.073398, -0.065920, -0.058009, -0.048810, -0.040714, -0.032533, -0.027328, -0.020402, -0.011382, -0.006547, -0.005452, -0.002712, 0.004649, 0.014201, 0.021442, 0.025510, 0.032890, 0.034711, 0.030965, 0.026329, 0.018828, 0.019246, 0.018861, 0.019611, 0.020596, 0.021396, 0.020172, 0.015723, 0.020537, 0.029677
	-0.063777, -0.066149, -0.073750, -0.076131, -0.084016, -0.091900, -0.093741, -0.094496, -0.094840, -0.089548, -0.084332, -0.077263, -0.068485, -0.061963, -0.051082, -0.043658, -0.037912, -0.032323, -0.024324, -0.019914, -0.018261, -0.013727, -0.003485, 0.004316, 0.011418, 0.017023, 0.022980, 0.024505, 0.018896, 0.014000, 0.009498, 0.006074, 0.009480, 0.007611, 0.008958, 0.010086, -0.000341, 0.010423, 0.010467, 0.016794
	-0.072341, -0.064233, -0.079217, -0.084483, -0.091050, -0.094481, -0.095378, -0.096667, -0.100564, -0.098313, -0.093254, -0.086700, -0.079209, -0.071795, -0.061313, -0.051911, -0.046317, -0.042643, -0.037228, -0.031598, -0.027431, -0.020480, -0.012883, -0.003114, 0.004746, 0.010189, 0.015911, 0.017106, 0.014037, 0.008693, 0.005120, 0.003652, -0.000532, -0.001097, 0.001984, 0.000397, -0.002089, -0.002821, 0.000529, 0.009043
	-0.068927, -0.075835, -0.083530, -0.085213, -0.091299, -0.100015, -0.101020, -0.100921, -0.103349, -0.102493, -0.098069, -0.091292, -0.083452, -0.079672, -0.069612, -0.062472, -0.055862, -0.052233, -0.046746, -0.041991, -0.035219, -0.028225, -0.018698, -0.007309, -0.002458, 0.002051, 0.006595, 0.008468, 0.005218, -0.000205, -0.003131, -0.003647, -0.006151, -0.009154, -0.005539, -0.006971, -0.015297, -0.002874, -0.005242, 0.003706
	-0.070116, -0.067835, -0.086390, -0.089881, -0.095167, -0.099194, -0.100751, -0.103794, -0.106996, -0.105835, -0.098564, -0.092154, -0.085579, -0.083053, -0.074722, -0.066442, -0.059302, -0.053429, -0.047800, -0.042952, -0.039132, -0.034614, -0.025732, -0.012689, -0.005906, 0.001101, 0.006644, 0.010980, 0.007742, 0.002526, -0.000261, -0.004094, -0.008771, -0.008465, -0.007095, -0.008952, -0.010405, -0.010446, -0.006121, 0.002024
	-0.064366, -0.071780, -0.082938, -0.085702, -0.093522, -0.099237, -0.104020, -0.105939, -0.106226, -0.104298, -0.097541, -0.091253, -0.084969, -0.082450, -0.075561, -0.066547, -0.056511, -0.051248, -0.041287, -0.037794, -0.035633, -0.028059, -0.019518, -0.010556, -0.003388, 0.002054, 0.009492, 0.011478, 0.008555, 0.004735, -0.000781, -0.006427, -0.005697, -0.010270, -0.006112, -0.011704, -0.018717, -0.002750, -0.010971, 0.000116
	-0.076795, -0.064801, -0.080209, -0.085175, -0.093457, -0.101077, -0.104981, -0.106367, -0.106821, -0.105708, -0.098545, -0.090759, -0.086929, -0.083491, -0.074306, -0.064805, -0.055933, -0.049959, -0.042853, -0.036270, -0.034463, -0.029587, -0.018780, -0.010103, -0.003533, 0.001632, 0.007909, 0.014370, 0.009281, 0.004666, -0.002974, -0.007301, -0.010185, -0.008299, -0.006340, -0.009678, -0.011333, -0.010684, -0.006289, 0.002763
	-0.067470, -0.065770, -0.074038, -0.076420, -0.085702, -0.098704, -0.101940, -0.102629, -0.101903, -0.100342, -0.093820, -0.086941, -0.083804, -0.081020, -0.067700, -0.059395, -0.054055, -0.047911, -0.039687, -0.035672, -0.032029, -0.025979, -0.017057, -0.006973, -0.001656, 0.002001, 0.007249, 0.012112, 0.006541, 0.000572, -0.006284, -0.010415, -0.012279, -0.015087, -0.007848, -0.016491, -0.019704, -0.005357, -0.013151, 0.002966
	-0.074820, -0.054794, -0.069710, -0.075127, -0.082743, -0.091434, -0.095621, -0.097541, -0.099098, -0.097422, -0.089851, -0.083594, -0.081112, -0.078942, -0.066391, -0.057457, -0.050942, -0.048077, -0.041211, -0.034391, -0.030091, -0.026047, -0.014207, -0.005090, 0.000912, 0.005316, 0.010043, 0.015509, 0.011199, 0.004513, -0.001027, -0.006694, -0.011239, -0.011162, -0.009134, -0.013596, -0.014031, -0.011306, -0.007627, 0.001767
	-0.061695, -0.056074, -0.065188, -0.067950, -0.076218, -0.088303, -0.093436, -0.092999, -0.090937, -0.090555, -0.084407, -0.080354, -0.078692, -0.074308, -0.062767, -0.052729, -0.047475, -0.043949, -0.036669, -0.031720, -0.027940, -0.020058, -0.010125, -0.000940, 0.003512, 0.007720, 0.011869, 0.015296, 0.011180, 0.003886, -0.003309, -0.003380, -0.007926, -0.011633, -0.003540, -0.014182, -0.013975, -0.003720, -0.011797, 0.006338
	-0.070864, -0.046187, -0.061128, -0.065717, -0.072715, -0.083470, -0.088292, -0.087558, -0.087628, -0.089378, -0.083768, -0.077237, -0.077063, -0.071978, -0.061635, -0.052022, -0.046913, -0.041194, -0.034314, -0.028661, -0.027048, -0.021438, -0.009769, -0.001205, 0.004637, 0.008928, 0.013264, 0.017277, 0.013442, 0.007295, 0.003623, -0.002524, -0.004256, -0.005789, -0.004213, -0.007305, -0.010487, -0.010885, -0.006086, 0.007386
	-0.059345, -0.049207, -0.056858, -0.060052, -0.066579, -0.080604, -0.086910, -0.085647, -0.085267, -0.087618, -0.081260, -0.075368, -0.073937, -0.069758, -0.058235, -0.051634, -0.045288, -0.038732, -0.032262, -0.027928, -0.024928, -0.019266, -0.007996, 0.000923, 0.005834, 0.008336, 0.013557, 0.017068, 0.012350, 0.006475, 0.000982, 0.001103, -0.006223, -0.006853, -0.000966, -0.013148, -0.013975, -0.006310, -0.011605, 0.006165
	-0.066591, -0.039715, -0.053663, -0.059514, -0.065911, -0.075018, -0.080214, -0.082968, -0.083447, -0.085380, -0.079055, -0.071985, -0.070247, -0.065856, -0.057767, -0.049975, -0.044481, -0.039103, -0.031217, -0.024927, -0.020997, -0.016440, -0.004831, 0.004061, 0.009463, 0.011160, 0.014777, 0.020638, 0.017816, 0.011360, 0.006171, 0.002164, -0.002119, -0.003117, -0.003031, -0.005156, -0.011400, -0.011762, -0.009295, -0.000001
	-0.060314, -0.046160, -0.052794, -0.054967, -0.062049, -0.074106, -0.080446, -0.081200, -0.080809, -0.080477, -0.076170, -0.070932, -0.069101, -0.063634, -0.055720, -0.049501, -0.044939, -0.040131, -0.032438, -0.022882, -0.017627, -0.012524, -0.001324, 0.006685, 0.011868, 0.013658, 0.016095, 0.021837, 0.020158, 0.012528, 0.006089, 0.005453, -0.000976, -0.002140, 0.001104, -0.010111, -0.010612, -0.007452, -0.014357, 0.001011
	-0.075633, -0.036609, -0.049346, -0.055490, -0.059336, -0.067616, -0.073859, -0.075613, -0.076372, -0.078009, -0.070627, -0.064206, -0.064430, -0.061999, -0.054551, -0.047386, -0.040817, -0.037398, -0.028062, -0.018505, -0.012195, -0.007531, 0.001481, 0.011790, 0.019955, 0.022349, 0.022131, 0.024492, 0.023359, 0.019186, 0.014655, 0.008357, 0.004176, 0.002971, 0.002955, -0.000237, -0.005884, -0.010152, -0.009506, 0.002811
	-0.059008, -0.039658, -0.046978, -0.048324, -0.052285, -0.063338, -0.069082, -0.070556, -0.070625, -0.070049, -0.064460, -0.057403, -0.056723, -0.052882, -0.046968, -0.041507, -0.033211, -0.029974, -0.022900, -0.013579, -0.008803, -0.004962, 0.005653, 0.017026, 0.028171, 0.028651, 0.024731, 0.026850, 0.023371, 0.017073, 0.015171, 0.016616, 0.005521, 0.005756, 0.007586, -0.005103, -0.006856, -0.005604, -0.006599, 0.007528
	-0.068330, -0.030233, -0.043154, -0.047439, -0.047149, -0.051149, -0.060971, -0.063014, -0.065775, -0.064636, -0.058200, -0.050987, -0.050925, -0.050115, -0.041299, -0.033907, -0.026306, -0.024199, -0.017123, -0.009196, -0.006314, -0.003809, 0.004760, 0.015324, 0.026665, 0.029649, 0.028724, 0.027131, 0.025150, 0.021808, 0.019981, 0.016766, 0.012347, 0.008776, 0.005760, -0.000224, -0.004294, -0.005879, -0.002457, 0.010054
	-0.053519, -0.031388, -0.038255, -0.037590, -0.039245, -0.046335, -0.056314, -0.057830, -0.060291, -0.058967, -0.051413, -0.045449, -0.043947, -0.042018, -0.034113, -0.025887, -0.019539, -0.017727, -0.012711, -0.005860, -0.003102, 0.000774, 0.009438, 0.015884, 0.022961, 0.024229, 0.026012, 0.029407, 0.026717, 0.020406, 0.017796, 0.020289, 0.012243, 0.009711, 0.009234, -0.005990, -0.001013, 0.000740, -0.002144, 0.013012
	-0.068972, -0.023416, -0.032912, -0.036134, -0.035915, -0.040435, -0.047452, -0.051460, -0.055021, -0.055776, -0.048697, -0.039554, -0.036785, -0.035561, -0.029056, -0.021075, -0.013416, -0.012134, -0.007237, -0.000622, 0.001662, 0.005393, 0.012038, 0.019764, 0.023514, 0.026252, 0.028191, 0.031400, 0.031365, 0.027993, 0.023275, 0.021009, 0.018930, 0.014093, 0.009022, 0.004773, 0.002094, 0.001348, 0.005643, 0.015078
	-0.050527, -0.022437, -0.028090, -0.026206, -0.028387, -0.036911, -0.041310, -0.044227, -0.046970, -0.046769, -0.038081, -0.031386, -0.029516, -0.024050, -0.019435, -0.012381, -0.005732, -0.004173, 0.000911, 0.006849, 0.007360, 0.010699, 0.017436, 0.023369, 0.028527, 0.029640, 0.031002, 0.034727, 0.036582, 0.030763, 0.026015, 0.028623, 0.020834, 0.016185, 0.016933, 0.002829, 0.004984, 0.009818, 0.008874, 0.020032
	-0.067395, -0.010220, -0.021024, -0.024567, -0.024087, -0.029620, -0.032317, -0.034341, -0.038392, -0.038789, -0.030285, -0.021590, -0.017175, -0.014435, -0.007732, -0.000529, 0.005605, 0.007078, 0.012454, 0.017758, 0.016774, 0.015574, 0.020748, 0.028369, 0.033644, 0.034771, 0.036537, 0.040293, 0.042118, 0.039979, 0.035655, 0.033354, 0.030928, 0.024890, 0.021491, 0.018938, 0.013668, 0.012501, 0.017108, 0.023515
	-0.038833, -0.012802, -0.018564, -0.017459, -0.019062, -0.027068, -0.030119, -0.028336, -0.029665, -0.030695, -0.022239, -0.013522, -0.008358, -0.004785, 0.000463, 0.010662, 0.015564, 0.016950, 0.020281, 0.025300, 0.022680, 0.022717, 0.026679, 0.031617, 0.035801, 0.037098, 0.041294, 0.045640, 0.047879, 0.042000, 0.038044, 0.040629, 0.033892, 0.031247, 0.031584, 0.018500, 0.020116, 0.019823, 0.016638, 0.029979
	-0.054356, -0.002258, -0.012712, -0.017288, -0.016713, -0.022907, -0.024293, -0.021563, -0.022620, -0.021953, -0.015330, -0.005386, -0.000764, 0.002640, 0.009997, 0.022869, 0.028174, 0.027730, 0.030977, 0.035707, 0.032818, 0.030889, 0.033638, 0.038561, 0.044265, 0.045141, 0.047683, 0.051815, 0.054004, 0.050991, 0.045574, 0.043899, 0.044055, 0.039092, 0.035909, 0.032091, 0.026891, 0.022169, 0.024865, 0.030848
	-0.031827, -0.000102, -0.006368, -0.006487, -0.006247, -0.014001, -0.017110, -0.013043, -0.010851, -0.008764, -0.000213, 0.006477, 0.011144, 0.018309, 0.024745, 0.033643, 0.038648, 0.039249, 0.041148, 0.045266, 0.041693, 0.040999, 0.045484, 0.052613, 0.057066, 0.054753, 0.055112, 0.059287, 0.060203, 0.052465, 0.047993, 0.050999, 0.047464, 0.046460, 0.044507, 0.031433, 0.032267, 0.032025, 0.029852, 0.040329
	-0.053848, 0.008122, -0.005187, -0.009032, -0.006543, -0.010012, -0.013005, -0.011663, -0.008957, -0.004668, 0.005458, 0.012800, 0.016893, 0.023554, 0.031737, 0.038741, 0.043870, 0.043337, 0.046621, 0.047581, 0.045654, 0.044827, 0.050363, 0.058747, 0.061023, 0.060485, 0.059059, 0.061821, 0.061391, 0.055971, 0.051067, 0.050038, 0.051018, 0.046533, 0.043334, 0.042562, 0.036118, 0.029798, 0.032773, 0.039524
	-0.025830, 0.006164, -0.000655, 0.000164, 0.000088, -0.008033, -0.011008, -0.006017, -0.001301, 0.004088, 0.011848, 0.020276, 0.024465, 0.033383, 0.039126, 0.044268, 0.047916, 0.047402, 0.050050, 0.050456, 0.048891, 0.051771, 0.058154, 0.063246, 0.065463, 0.063072, 0.060950, 0.065351, 0.064614, 0.057455, 0.051194, 0.055723, 0.050906, 0.046407, 0.048283, 0.036561, 0.037400, 0.036887, 0.031589, 0.046759
	-0.041184, 0.017683, 0.006408, 0.000358, 0.001923, -0.002498, -0.003907, -0.001746, 0.001864, 0.006784, 0.017297, 0.026916, 0.030940, 0.036439, 0.045987, 0.050809, 0.054636, 0.052055, 0.053180, 0.056698, 0.057069, 0.055779, 0.063193, 0.067815, 0.071856, 0.070651, 0.067674, 0.070718, 0.070797, 0.062598, 0.057842, 0.056835, 0.056713, 0.051260, 0.048727, 0.048227, 0.044844, 0.039559, 0.041218, 0.044920
	-0.014008, 0.018619, 0.011274, 0.010878, 0.008771, 0.001246, -0.001819, 0.003600, 0.008052, 0.011983, 0.021970, 0.030757, 0.037662, 0.045972, 0.053195, 0.057661, 0.059206, 0.058383, 0.060240, 0.061039, 0.062504, 0.064497, 0.070278, 0.077704, 0.080246, 0.077015, 0.072985, 0.075685, 0.072584, 0.063534, 0.057732, 0.061938, 0.057545, 0.050931, 0.054863, 0.045820, 0.048882, 0.049675, 0.043484, 0.051538
	-0.045038, 0.028947, 0.019821, 0.012917, 0.013648, 0.007951, 0.005122, 0.007823, 0.012411, 0.015320, 0.025036, 0.036734, 0.045314, 0.052208, 0.062220, 0.065610, 0.068489, 0.066665, 0.068454, 0.069025, 0.071080, 0.073373, 0.079623, 0.085651, 0.088907, 0.088954, 0.084254, 0.084464, 0.080300, 0.072471, 0.067316, 0.066430, 0.065143, 0.057630, 0.058650, 0.059627, 0.057197, 0.054105, 0.055295, 0.057879
	-0.017117, 0.027364, 0.023067, 0.022758, 0.019246, 0.011825, 0.007962, 0.011522, 0.017237, 0.021779, 0.031329, 0.042642, 0.052349, 0.060322, 0.069568, 0.074657, 0.075211, 0.072882, 0.075373, 0.078391, 0.079512, 0.081816, 0.086101, 0.091730, 0.095061, 0.095682, 0.092100, 0.092873, 0.085769, 0.077219, 0.068392, 0.073179, 0.069972, 0.061240, 0.068306, 0.062227, 0.061008, 0.064520, 0.058543, 0.070728
	-0.042759, 0.035472, 0.029514, 0.023812, 0.024176, 0.020576, 0.017397, 0.018716, 0.022981, 0.027634, 0.041262, 0.050991, 0.058558, 0.067060, 0.077829, 0.083609, 0.084719, 0.082815, 0.085352, 0.087363, 0.091238, 0.091692, 0.096562, 0.102513, 0.106436, 0.108184, 0.105828, 0.107257, 0.102415, 0.090768, 0.084257, 0.081410, 0.081286, 0.073523, 0.074433, 0.076576, 0.070376, 0.068350, 0.071896, 0.072962
	-0.003143, 0.035517, 0.033266, 0.032727, 0.031843, 0.025862, 0.023177, 0.026936, 0.032953, 0.037457, 0.049289, 0.057429, 0.066625, 0.072540, 0.083814, 0.089321, 0.092420, 0.093053, 0.094752, 0.096876, 0.098364, 0.101271, 0.105185, 0.113505, 0.115784, 0.118957, 0.117138, 0.117934, 0.110930, 0.101497, 0.091051, 0.092731, 0.090574, 0.079282, 0.084691, 0.078426, 0.073451, 0.081698, 0.072811, 0.084352
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 19.8
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 130, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 123, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 112, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/neopixel.py", line 111, in load_config_prefix
    return PrinterNeoPixel(config)
  File "/home/pi/klipper/klippy/extras/neopixel.py", line 42, in __init__
    raise config.error("neopixel chain too long")
configparser.Error: neopixel chain too long
webhooks client 4131141928: New connection
webhooks client 4131141928: Client info {'program': 'Moonraker', 'version': 'v0.9.3-0-g71f9e67'}
Starting Klippy...
Args: ['/home/pi/klipper/klippy/klippy.py', '/home/pi/printer_data/config/printer.cfg', '-l', '/home/pi/printer_data/logs/klippy.log', '-I', '/home/pi/printer_data/comms/klippy.serial', '-a', '/home/pi/printer_data/comms/klippy.sock']
Git version: 'v0.12.0-402-g2817b348e-dirty'
Untracked files: klippy/extras/beacon.py, klippy/extras/beacon_adaptive_heat_soak.py, klippy/extras/beacon_mesh.py, klippy/extras/beacon_true_zero_correction.py, klippy/extras/beacon_user_z_offset.py, klippy/extras/fastconfig.py, klippy/extras/gcode_shell_command.py, klippy/extras/linear_movement_vibrations.py, klippy/extras/named_offsets.py, klippy/extras/ratos.py, (+4 files)
Branch: master
Remote: origin
Tracked URL: https://github.com/Klipper3d/klipper.git
CPU: 4 core ?
Python: '3.9.2 (default, Jan 24 2026, 09:41:14) \n[GCC 10.2.1 20210110]'
Start printer at Tue Mar 17 03:53:56 2026 (1773719636.9 9241.3)
===== Config file =====
[mcu rpi]
serial = /tmp/klipper_host_mcu

[board_pins btt-octopus-pro-h723-11]
aliases = 
	
	
	
	x_step_pin=PF13,
	x_dir_pin=PF12,
	x_enable_pin=PF14,
	x_uart_pin=PC4,
	x_diag_pin=PG6,
	x_endstop_pin=PG6,
	
	
	
	dual_carriage_step_pin=PF9,
	dual_carriage_dir_pin=PF10,
	dual_carriage_enable_pin=PG2,
	dual_carriage_uart_pin=PF2,
	dual_carriage_diag_pin=PG12,
	dual_carriage_endstop_pin=PG12,
	
	
	
	y_step_pin=PG0,
	y_dir_pin=PG1,
	y_enable_pin=PF15,
	y_uart_pin=PD11,
	y_diag_pin=PG9,
	y_endstop_pin=PG9,
	
	
	
	y1_step_pin=PG4,
	y1_dir_pin=PC1,
	y1_enable_pin=PA2,
	y1_uart_pin=PC7,
	y1_diag_pin=PG11,
	y1_endstop_pin=PG11,
	
	
	
	z0_step_pin=PC13,
	z0_dir_pin=PF0,
	z0_enable_pin=PF1,
	z0_uart_pin=PE4,
	z0_diag_pin=PG13,
	
	
	
	z1_step_pin=PE2,
	z1_dir_pin=PE3,
	z1_enable_pin=PD4,
	z1_uart_pin=PE1,
	z1_diag_pin=PG14,
	
	
	
	z2_step_pin=PE6,
	z2_dir_pin=PA14,
	z2_enable_pin=PE0,
	z2_uart_pin=PD3,
	z2_diag_pin=PG15,
	
	e_step_pin=PF11,
	e_dir_pin=PG3,
	e_enable_pin=PG5,
	e_uart_pin=PC6,
	
	e_heater_pin=PA2,
	e_sensor_pin=PF4,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=PA7,
	stepper_spi_miso_pin=PA6,
	stepper_spi_sclk_pin=PA5,
	adxl345_cs_pin=PA15,
	bltouch_sensor_pin=PB7,
	bltouch_control_pin=PB6,
	probe_pin=PB7,
	fan_part_cooling_pin=PA8,
	fan_toolhead_cooling_pin=PE5,
	fan_controller_board_pin=PD12,
	heater_bed_heating_pin=PA1,
	heater_bed_sensor_pin=PF3,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PG15,
	filament_sensor_motion_pin=PG14,
	ratrig_vaoc_probe_pin=PG10,
	ratrig_vaoc_led_pin=PB0,
	ratrig_vaoc_fan_pin=PD13,
	chamber_lighting_pin=PB11,
	chamber_filter_4p_fan_pin=PD14,
	chamber_filter_4p_fan_enable_pin=PD15

[mcu]
serial = /dev/RatOS/btt-octopus-pro-h723-11

[temperature_sensor Octopus_Pro_H723_V1.1]
sensor_type = temperature_mcu

[adxl345 controlboard]
cs_pin = PA15
spi_software_mosi_pin = PB5
spi_software_miso_pin = PB4
spi_software_sclk_pin = PB3

[board_pins toolboard_t0]
mcu = toolboard_t0
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t0]
serial = /dev/RatOS/btt-ebb42-gen2-10-t0

[temperature_sensor EBB42_Gen2_v1.0_T0]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t0

[lis2dw toolboard_t0]
axes_map = x, z, y
cs_pin = toolboard_t0:PB1
spi_software_mosi_pin = toolboard_t0:PB11
spi_software_miso_pin = toolboard_t0:PB2
spi_software_sclk_pin = toolboard_t0:PB10

[board_pins toolboard_t1]
mcu = toolboard_t1
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t1]
serial = /dev/RatOS/btt-ebb42-gen2-10-t1

[temperature_sensor EBB42_Gen2_v1.0_T1]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t1

[lis2dw toolboard_t1]
axes_map = x, z, y
cs_pin = toolboard_t1:PB1
spi_software_mosi_pin = toolboard_t1:PB11
spi_software_miso_pin = toolboard_t1:PB2
spi_software_sclk_pin = toolboard_t1:PB10

[gcode_macro RatOS]
variable_homing = "endstops"
variable_z_probe = "static"
variable_sensorless_x_current = 0.6
variable_sensorless_y_current = 0.9
variable_safe_home_x = "middle"
variable_safe_home_y = "middle"
variable_driver_type_x = "tmc2209"
variable_driver_type_y = "tmc2209"
variable_stowable_probe_stop_on_error = False
variable_chamber_filter_enable = True
variable_chamber_filter_speed = 0.5
variable_chamber_filter_disable_speed = 1.0
variable_chamber_filter_enable_at = "after_print_start"
variable_chamber_filter_disable_period = 300
variable_chamber_filter_disable_bed_temp = 0
variable_chamber_heater_enable = True
variable_chamber_heater_bed_temp = 115
variable_chamber_heater_preheating_temp = 150
variable_chamber_heater_heating_temp_offset = 25
variable_chamber_heater_control_external_heater = False
variable_chamber_heater_air_circulation_enable = True
variable_chamber_heater_air_circulation_fan_speed = 0.35
variable_chamber_heater_air_circulation_y_pos = 0
variable_chamber_heater_air_circulation_z_pos = 100
variable_chamber_heater_extra_fan_speed = 1.0
variable_chamber_heater_filter_fan_speed = 1.0
variable_bed_heat_soak_time = 0
variable_hotend_heat_soak_time = 0
variable_led_status_action = 0.0,1.0,1.0
variable_led_status_success = 0.0,1.0,0.0
variable_led_status_error = 1.0,0.0,1.0
variable_led_status_on = 1.0,1.0,1.0
variable_led_status_off = 0.0,0.0,1.0
variable_led_status_standby = 0.1,0.1,0.1
variable_led_status_heating = 1.0,0.0,0.0
variable_led_status_cooling = 0.0,0.0,1.0
variable_calibrate_bed_mesh = True
variable_adaptive_mesh = True
variable_start_print_park_in = "center"
variable_start_print_park_z_height = 3
variable_end_print_park_in = "back"
variable_pause_print_park_in = "back"
variable_end_print_park_z_hop = 20
variable_nozzle_priming = "primeblob"
variable_nozzle_prime_start_x = "max"
variable_nozzle_prime_start_y = "min"
variable_nozzle_prime_direction = "auto"
variable_nozzle_prime_bridge_fan = 102
variable_probe_for_priming_result = None
variable_probe_for_priming_end_result = None
variable_probe_for_priming_result_t1 = None
variable_probe_for_priming_end_result_t1 = None
variable_probe_for_priming_disable_mesh_constraints = False
variable_adaptive_prime_offset_threshold = -1.0
variable_last_z_offset = None
variable_runout_park_in = "front"
variable_enable_unload_tip_forming = False
variable_filament_unload_length = 150
description = RatOS variable storage macro, will echo variables to the console when run.
variable_relative_extrusion = True
variable_force_absolute_position = False
variable_preheat_extruder = True
variable_preheat_extruder_temp = 150
variable_macro_travel_speed = 600
variable_macro_travel_accel = 8000
variable_macro_z_speed = 15
variable_bed_margin_x = [59.6, 59.6]
variable_bed_margin_y = [14.35, 33.65]
variable_printable_x_min = 0
variable_printable_x_max = 0
variable_printable_y_min = 0
variable_printable_y_max = 0
variable_end_print_motors_off = True
variable_status_color_ok = "00FF00"
variable_status_color_error = "FF0000"
variable_status_color_unknown = "FFFF00"
variable_end_print_retract_filament = 10
gcode = 
	ECHO_RATOS_VARS
variable_auto_center_subject = False
variable_toolchange_zhop = 2.0
variable_toolchange_zspeed = 25
variable_toolchange_sync_fans = False
variable_toolchange_combined_zhop = False
variable_toolchange_travel_speed = 600
variable_toolchange_travel_accel = 8000
variable_toolchange_extrusion = 2.0
variable_toolchange_retraction = 2.0
variable_toolchange_feedrate = 7200
variable_toolchange_prepurging_timer = 0
variable_toolchange_standby_temp = -1
variable_toolchange_purge = 25
variable_toolchange_first_purge = 50
variable_beacon_bed_mesh_scv = 25
variable_beacon_contact_z_homing = False
variable_beacon_contact_start_print_true_zero = True
variable_beacon_contact_start_print_true_zero_fuzzy_position = True
variable_beacon_contact_calibrate_model_on_true_zero = True
variable_beacon_contact_wipe_before_true_zero = True
variable_beacon_contact_wipe_before_true_zero_method = "probe_clean"
variable_beacon_contact_true_zero_temp = 170
variable_beacon_contact_prime_probing = True
variable_beacon_contact_expansion_compensation = True
variable_beacon_contact_bed_mesh = False
variable_beacon_contact_bed_mesh_samples = 2
variable_beacon_contact_z_tilt_adjust = False
variable_beacon_contact_z_tilt_adjust_samples = 2
variable_beacon_scan_compensation_enable = True
variable_beacon_scan_compensation_profile = "auto"
variable_beacon_scan_compensation_desired_spacing = 10
variable_beacon_scan_compensation_bed_temp_mismatch_is_error = False
variable_beacon_contact_poke_bottom_limit = -1
variable_beacon_scan_method_automatic = False
variable_beacon_adaptive_heat_soak = True
variable_beacon_adaptive_heat_soak_max_wait = 5400
variable_beacon_adaptive_heat_soak_extra_wait_after_completion = 0
variable_beacon_adaptive_heat_soak_layer_quality = 3
variable_beacon_adaptive_heat_soak_maximum_first_layer_duration = 1800
variable_beacon_contact_start_print_true_zero_fuzzy_radius = 20
variable_homing_x = "endstop"
variable_homing_y = "endstop"
variable_default_toolhead = 0
variable_adxl_chip = ["lis2dw toolboard_t0", "lis2dw toolboard_t1"]
variable_shaper_x_freq = [54.2, 53.2, 53.6, 54.4]
variable_shaper_y_freq = [40.8, 47.6, 38.6, 38]
variable_shaper_x_type = ["mzv", "mzv", "mzv", "mzv"]
variable_shaper_y_type = ["mzv", "mzv", "mzv", "mzv"]
variable_x_driver_types = ["tmc5160"]
variable_x_axes = ["x"]
variable_y_driver_types = ["tmc5160", "tmc5160"]
variable_y_axes = ["y", "y1"]
variable_z_driver_types = ["tmc2209", "tmc2209", "tmc2209"]
variable_z_axes = ["z", "z1", "z2"]
variable_home_y_first = True

[ratos_homing]
axes = xyz
z_hop = 15
z_hop_speed = 15
gcode = 
	
	_LED_ON
	
	
	{% set prev_stop_on_error = printer["gcode_macro RatOS"].stowable_probe_stop_on_error %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set target_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	_IDEX_SINGLE
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE=True
	
	
	M400
	
	G90
	
	
	{% set X = true if params.X is defined else false %}
	{% set Y = true if params.Y is defined else false %}
	{% set Z = true if params.Z is defined else false %}
	{% if printer["gcode_macro RatOS"].home_y_first|default(false)|lower == 'true' %}
	HOME_Y X={X} Y={Y} Z={Z}
	HOME_X X={X} Y={Y} Z={Z}
	{% else %}
	HOME_X X={X} Y={Y} Z={Z}
	HOME_Y X={X} Y={Y} Z={Z}
	{% endif %}
	HOME_Z X={X} Y={Y} Z={Z}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE={prev_stop_on_error}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[gcode_macro HOME_X]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_x = printer["gcode_macro RatOS"].homing_x|lower %}
	{% set homing_x = homing_x if homing_x else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_X" MSG="printable_x_max: {printable_x_max}, safe_home_x: {safe_home_x}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}"
	
	
	{% if X or not Y and not Z %}
	{% if homing_x == 'endstop' %}
	G28 X
	{% elif homing_x == 'sensorless' %}
	{% if printer["dual_carriage"] is defined %}
	{ action_emergency_stop("sensorless homing not supported on IDEX!") }
	{% endif %}
	HOME_X_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_x to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_x, homing)) }
	{% endif %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1} MODE=PRIMARY
	G1 X{parking_position} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	{% endif %}
	{% set x_homed = True %}
	G0 X{safe_home_x} F{speed}
	M400
	{% endif %}

[gcode_macro HOME_Y]
gcode = 
	
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_y = printer["gcode_macro RatOS"].homing_y|lower %}
	{% set homing_y = homing_y if homing_y else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Y" MSG="printable_y_max: {printable_y_max}, safe_home_y: {safe_home_y}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}"
	
	
	{% if Y or not X and not Z %}
	{% if homing_y == 'endstop' %}
	G28 Y
	{% elif homing_y == 'sensorless' %}
	HOME_Y_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_y to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_y, homing)) }
	{% endif %}
	{% set y_homed = True %}
	G0 Y{safe_home_y} F{speed}
	{% endif %}

[gcode_macro HOME_Z]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	
	
	{% set beacon_contact_z_homing = true if printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_z_home_position_fuzzing_radius = printer["gcode_macro RatOS"].beacon_z_home_position_fuzzing_radius|default(0)|float %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Z" MSG="x_homed: {x_homed}, y_homed: {y_homed}, z_probe: {z_probe}, beacon_contact_z_homing: {beacon_contact_z_homing}"
	
	
	{% if Z or not Y and not X %}
	RATOS_ECHO MSG="Homing Z"
	{% if x_homed == False or y_homed == False %}
	{ action_emergency_stop("X and Y must be homed before homing Z") }
	{% else %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_homing %}
	{% if beacon_contact_start_print_true_zero %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% else %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	{% else %}
	G28 Z
	{% endif %}
	_Z_HOP
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro HOME_X_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	
	G4 P300
	
	G28 X
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"

[gcode_macro HOME_Y_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	
	G4 P300
	
	G28 Y
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"

[gcode_macro _Z_HOP]
description = Move Z axis up by Z_HOP distance at Z_HOP_SPEED. In relative mode it will move Z axis up by Z_HOP distance. In absolute mode it will move Z axis to Z_HOP distance.
gcode = 
	{% set z_hop = printer.fastconfig.config.ratos_homing.z_hop|float %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	G0 Z{z_hop} F{z_hop_speed}

[gcode_macro __MOVE_TO_SAFE_Z_HOME_ECHO_DEBUG]
gcode = 
	DEBUG_ECHO PREFIX="_MOVE_TO_SAFE_Z_HOME" MSG="x: {params.X}, y: {params.Y}, z_hop: {params.Z_HOP}, fuzzy_radius: {params.FUZZY_RADIUS}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}, printable_x_max: {printer['gcode_macro RatOS'].printable_x_max}, printable_y_max: {printer['gcode_macro RatOS'].printable_y_max}"

[gcode_macro MAYBE_HOME]
description = Only home unhomed axis. Specify ABL=1 to also ensure that automatic bed levelling is applied (if configured).
variable_is_kinematic_position_overriden = False
gcode = 
	{% set abl = params.ABL|default('')|lower in ('true', 'yes', '1') %}
	{% if printer["gcode_macro MAYBE_HOME"].is_kinematic_position_overriden|lower == 'true' %}
	RATOS_ECHO MSG="SET_CENTER_KINEMATIC_POSITION has been abused. Homing all axes. Please refrain from using SET_CENTER_KINEMATIC_POSITION outside of debugging purposes."
	G28
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=False
	{% else %}
	{% set axes = '' %}
	{% set isHomed = true %}
	{% set axesToHome = '' %}
	{% if params.X is defined %}
	{% set axes = axes ~ 'X ' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% endif %}
	{% if params.Y is defined %}
	{% set axes = axes ~ 'Y ' %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% endif %}
	{% if params.Z is defined %}
	{% set axes = axes ~ 'Z ' %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if params.X is not defined and params.Y is not defined and params.Z is not defined %}
	{% set axes = '' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if isHomed is false %}
	RATOS_ECHO MSG="Homing {axesToHome}"
	G28 {axesToHome}
	{% else %}
	RATOS_ECHO MSG="All requested axes already homed. Skipping homing."
	{% endif %}
	{% endif %}
	{% if abl %}
	{% if printer.z_tilt is defined %}
	{% if not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Performing Z tilt adjustment..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Z tilt already applied. Skipping Z tilt adjustment."
	{% endif %}
	{% elif printer.quad_gantry_level is defined %}
	{% if not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Performing quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Quad gantry leveling already applied. Skipping quad gantry leveling."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="No automatic bed leveling method configured. Skipping bed leveling."
	{% endif %}
	{% endif %}

[gcode_macro PID_CALIBRATE_HOTEND]
description = Perform a PID calibration test for a given extruder heater.
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set temp = params.TEMP|default(220)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_HOTEND" MSG="TEMP={temp}"
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO MSG="PID calibration hotend heater T0 at {temp}°C..."
	PID_CALIBRATE HEATER=extruder TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	
	{% if toolhead==0 or toolhead==1 %}
	RATOS_ECHO MSG="PID calibration hotend heater T{toolhead} at {temp}°C..."
	PID_CALIBRATE HEATER=extruder{'' if toolhead==0 else toolhead} TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_BED]
description = Perform a PID calibration test for the bed heater.
gcode = 
	
	{% set temp = params.TEMP|default(80)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_BED" MSG="TEMP={temp}"
	RATOS_ECHO MSG="PID calibration bed heater at {temp}°C..."
	
	
	PID_CALIBRATE HEATER=heater_bed TARGET={temp}
	
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_CHAMBER_HEATER]
description = Perform a PID calibration test for the chamber heater.
gcode = 
	
	{% set temp = params.TEMP|default(150)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_CHAMBER_HEATER" MSG="TEMP={temp}"
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	RATOS_ECHO MSG="PID calibration chamber heater at {temp}°C..."
	PID_CALIBRATE HEATER=chamber_heater TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_heater" %}
	{% set link_text = "RatOS Chamber Heater" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber heater found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro INITIALIZE_PA_TUNING]
description = Start a pressure advance tuning tower.
gcode = 
	
	{% set start = params.START|default(0.0)|float %}
	{% set factor = params.FACTOR|default(0.001)|float %}
	
	
	{% set layer_number = printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|default(0)|int %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if is_printing_gcode and layer_number < 2 %}
	DEBUG_ECHO PREFIX="START_PA_TOWER" MSG="START: {start}, FACTOR: {factor}"
	RATOS_ECHO MSG="Starting pressure advance tuning tower..."
	TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START={start} FACTOR={factor}
	{% else %}
	RATOS_ECHO MSG="Pressure advance tuning tower requires you to be printing gcode and on layer 1 to start."
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro CHAMBER_FILTER_ON]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	_CHAMBER_FILTER_TURN_ON
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro CHAMBER_FILTER_OFF]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Deactivating chamber filter..."
	_CHAMBER_FILTER_TURN_OFF
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set chamber_filter_enable_at = printer["gcode_macro RatOS"].chamber_filter_enable_at|default('after_print_start')|lower %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_ON" MSG="at: {at}, chamber_filter_enable: {chamber_filter_enable}, chamber_filter_enable_at: {chamber_filter_enable_at}, chamber_filter_speed: {chamber_filter_speed}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	{% if chamber_filter_enable_at == at %}
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	
	
	_CHAMBER_FILTER_TURN_ON AT={at}
	
	
	{% if chamber_filter_enable_at == "print_end" %}
	_LED_CHAMBER_FILTER_ON
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_OFF]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF" MSG="chamber_filter_enable: {chamber_filter_enable}, filter_disable_period: {filter_disable_period}, filter_disable_bed_temp: {filter_disable_bed_temp}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	
	{% if filter_disable_period > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting {filter_disable_period} seconds before turning chamber filter off..."
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION={filter_disable_period}
	{% endif %}
	
	
	{% if filter_disable_bed_temp > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting for bed temp to cool down to {filter_disable_bed_temp}°C to turn filter off..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM=0 MAXIMUM={filter_disable_bed_temp}
	_CHAMBER_FILTER_TURN_OFF
	_LED_CHAMBER_FILTER_OFF
	{% endif %}
	
	{% endif %}

[delayed_gcode _CHAMBER_FILTER_OFF_TIMER]
gcode = 
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF_TIMER" MSG="executed"
	
	
	_CHAMBER_FILTER_TURN_OFF
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Chamber filter turned off!"
	
	
	_LED_CHAMBER_FILTER_OFF

[gcode_macro _CHAMBER_FILTER_TURN_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_speed|default(0)|float %}
	{% if at == "print_end" %}
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_disable_speed|default(0)|float %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION=0
	
	
	SET_FAN_SPEED FAN=filter SPEED={chamber_filter_speed}

[gcode_macro _CHAMBER_FILTER_TURN_OFF]
gcode = 
	
	SET_FAN_SPEED FAN=filter SPEED=0

[gcode_macro _CHAMBER_FILTER_SANITY_CHECK]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	{% if filter_disable_bed_temp > 0 and filter_disable_period > 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable, not both.")}
	{% endif %}
	
	{% if filter_disable_bed_temp == 0 and filter_disable_period == 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable.")}
	{% endif %}
	
	{% endif %}

[gcode_macro CHAMBER_HEATER_ON]
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(45)|int %}
	
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp} IS_FROM_START_PRINT=False

[gcode_macro CHAMBER_HEATER_OFF]
gcode = 
	_CHAMBER_HEATER_OFF

[gcode_macro _CHAMBER_HEATER_ON]
variable_chamber_temp = 0
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	{% set is_from_start_print = true if params.IS_FROM_START_PRINT|default(True)|lower == 'true' else false %}
	
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set chamber_heater_enable = true if printer["gcode_macro RatOS"].chamber_heater_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}
	{% set chamber_heater_preheating_temp = printer["gcode_macro RatOS"].chamber_heater_preheating_temp|default(150)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	{% set chamber_heater_control_external_heater = true if printer["gcode_macro RatOS"].chamber_heater_control_external_heater|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_enable = true if printer["gcode_macro RatOS"].chamber_heater_air_circulation_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_fan_speed = printer["gcode_macro RatOS"].chamber_heater_air_circulation_fan_speed|default(0.35)|float %}
	{% set chamber_heater_air_circulation_y_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_y_pos|default(0)|float %}
	{% set chamber_heater_air_circulation_z_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_z_pos|default(100)|float %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_HEATER_ON" MSG="chamber_heater_enable: {chamber_heater_enable}, chamber_heater_preheating_temp: {chamber_heater_preheating_temp}, chamber_heater_heating_temp_offset: {chamber_heater_heating_temp_offset}, bed_temp: {bed_temp}, chamber_temp: {chamber_temp}, start_chamber_temp: {start_chamber_temp}"
	
	
	{% if chamber_heater_enable and chamber_temp > 0 and chamber_heater_bed_temp > 0 %}
	
	
	_LED_HEATING
	
	
	RATOS_ECHO MSG="Preheating chamber to {(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}°C..."
	
	
	{% set chamber_temp_sensor = "extruder" %}
	{% if printer["dual_carriage"] is defined and default_toolhead == 1 %}
	{% set chamber_temp_sensor = "extruder1" %}
	{% endif %}
	{% if printer["temperature_sensor chamber"] is defined %}
	{% set chamber_temp_sensor = "temperature_sensor chamber" %}
	{% endif %}
	
	
	{% set current_chamber_temp = printer['%s' % chamber_temp_sensor].temperature|int %}
	
	
	{% set needs_heating = current_chamber_temp < (start_chamber_temp if start_chamber_temp > 0 else chamber_temp) %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_BEFORE_PREHEATING
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	{% if not is_from_start_print %}
	MAYBE_HOME
	{% endif %}
	G0 Z{chamber_heater_air_circulation_z_pos} F{z_speed}
	G0 Y{chamber_heater_air_circulation_y_pos} F{speed}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * chamber_heater_air_circulation_fan_speed)}
	{% endif %}
	{% else %}
	{% if is_from_start_print %}
	G0 Z{z} F{z_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE={chamber_temp}
	
	
	{% if needs_heating %}
	
	
	M140 S{chamber_heater_bed_temp}
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={chamber_heater_preheating_temp}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	
	{% endif %}
	
	
	{% if needs_heating %}
	_CHAMBER_HEATER_EXTRA_FAN_ON
	{% endif %}
	
	
	{% if needs_heating %}
	TEMPERATURE_WAIT SENSOR="{chamber_temp_sensor}" MINIMUM={(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% endif %}
	
	
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED=0
	_CHAMBER_FILTER_ON AT="before_print_start"
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	G28 Z
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_AFTER_PREHEATING
	{% endif %}
	
	
	{% if printer["temperature_sensor chamber"] is defined %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined and chamber_heater_control_external_heater %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	
	
	_LED_SUCCESS
	
	{% endif %}

[gcode_macro _CHAMBER_HEATER_OFF]
gcode = 
	RATOS_ECHO MSG="Deactivating chamber heater..."
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=0
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE=0
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	
	
	_CHAMBER_HEATER_EXTRA_FAN_OFF

[delayed_gcode _CHAMBER_HEATER_CONTROL]
initial_duration = 0.
gcode = 
	
	{% set chamber_temp = printer["gcode_macro _CHAMBER_HEATER_ON"].chamber_temp|default(0)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	
	
	{% set current_chamber_temp = printer['temperature_sensor chamber'].temperature|int %}
	
	
	{% if current_chamber_temp < chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	{% endif %}
	
	
	{% if current_chamber_temp >= chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_ON]
gcode = 
	
	{% set chamber_heater_extra_fan_speed = printer["gcode_macro RatOS"].chamber_heater_extra_fan_speed|default(0.0)|float %}
	
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	{% if chamber_heater_extra_fan_speed > 0 %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED={chamber_heater_extra_fan_speed}
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_OFF]
gcode = 
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED=0
	{% endif %}

[gcode_macro _USER_CHAMBER_HEATER_BEFORE_PREHEATING]
description = Will be executed before chamber preheating, only if heating is needed.
gcode = 

[gcode_macro _USER_CHAMBER_HEATER_AFTER_PREHEATING]
description = Will be executed after chamber preheating, only if heating was needed.
gcode = 

[gcode_macro RESET_HEATSOAK_SETTINGS]
description = Resets all heatsoak-related settings to startup defaults
gcode = 
	HEATSOAK_SETTINGS ACTION=reset

[gcode_macro USE_ADAPTIVE_HEATSOAK]
description = Temporarily enables adaptive bed heatsoaking (if a beacon probe is present), will reset to printer.cfg settings
	when Klipper is restarted. Optionally specify QUALITY (1-5) and maximum FIRST_LAYER_DURATION (in minutes).
	Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.QUALITY|default("1..5") %}
	{% set _ = params.FIRST_LAYER_DURATION|default("1..120 minutes") %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("Adaptive heatsoaking is only available when a beacon probe is configured.") }
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_quality = (settings.variable_beacon_adaptive_heat_soak_layer_quality if defsrc == 'startup' else current.beacon_adaptive_heat_soak_layer_quality)|default(3)|int %}
	{% set default_first_layer_duration_secs = (settings.variable_beacon_adaptive_heat_soak_maximum_first_layer_duration if defsrc == 'startup' else current.beacon_adaptive_heat_soak_maximum_first_layer_duration)|default(1800)|int %}
	{% if params2.QUALITY is defined %}
	{% set quality = params2.QUALITY|int %}
	{% if quality < 1 or quality > 5 %}
	{ action_raise_error("QUALITY must be between 1 (rough) and 5 (maximum). Use 3 (normal) if unsure.") }
	{% endif %}
	{% else %}
	{% set quality = default_quality %}
	{% endif %}
	{% if params2.FIRST_LAYER_DURATION is defined %}
	{% set first_layer_duration_mins = params2.FIRST_LAYER_DURATION|float %}
	{% if first_layer_duration_mins <= 0 %}
	{ action_raise_error("FIRST_LAYER_DURATION must be a positive number specifying the maximum first layer duration in minutes.") }
	{% endif %}
	{% if first_layer_duration_mins > 120 %}
	CONSOLE_ECHO MSG="FIRST_LAYER_DURATION will be limited to 120 minutes. Values larger than this will not have an effect on soak time."
	{% set first_layer_duration_mins = 120 %}
	{% endif %}
	{% set first_layer_duration_secs = (first_layer_duration_mins * 60.0)|int %}
	{% else %}
	{% set first_layer_duration_secs = default_first_layer_duration_secs %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	{% endif %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=True beacon_adaptive_heat_soak_layer_quality={quality} beacon_adaptive_heat_soak_maximum_first_layer_duration={first_layer_duration_secs}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."

[gcode_macro USE_FIXED_HEATSOAK]
description = Temporarily enables fixed bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
	Optionally specify DURATION (in minutes). Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.DURATION|default("0..720 minutes") %}
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_duration = (settings.variable_bed_heat_soak_time if defsrc == 'startup' else current.bed_heat_soak_time)|default(0)|int %}
	{% if params2.DURATION is defined %}
	{% set duration_mins = params2.DURATION|float %}
	{% if duration_mins < 0 %}
	{ action_raise_error("DURATION must be a non-negative number specifying the heatsoak duration in minutes.") }
	{% endif %}
	{% if duration_mins > 720 %}
	CONSOLE_ECHO MSG="DURATION will be limited to 720 minutes (12 hours). If you really need a larger value, adjust printer.cfg instead."
	{% set duration_mins = 720 %}
	{% endif %}
	{% set duration_secs = (duration_mins * 60.0)|int %}
	{% else %}
	{% set duration_secs = default_duration %}
	{% set duration_mins = duration_secs / 60.0 %}
	{% endif %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% if has_beacon %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=False bed_heat_soak_time={duration_secs}
	{% else %}
	HEATSOAK_SETTINGS QUIET=1 bed_heat_soak_time={duration_secs}
	{% endif %}
	{% if duration_mins < 1e-3 %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% else %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% endif %}

[gcode_macro USE_NO_HEATSOAK]
description = Temporarily disables bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
gcode = 
	USE_FIXED_HEATSOAK DURATION=0

[gcode_macro HEATSOAK_SETTINGS]
description = Shows or adjusts heatsoak settings
	- With no arguments: shows current heatsoak settings, specify VERBOSE=1 for detailed output
	- With arguments: sets the specified settings. Use the full setting name without the variable_ prefix, e.g. bed_heat_soak_time=300 or beacon_adaptive_heat_soak_layer_quality=4. See printer.cfg for available settings.
variable_default_source = "startup"
gcode = 
	
	{% set params2 = params %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% set quiet = params2.pop("QUIET", None)|default("0") in ("1", "true", "yes") %}
	{% set verbose = params2.pop("VERBOSE", None)|default("0") in ("1", "true", "yes") %}
	{% if has_beacon %}
	{% set vars = (
	"beacon_adaptive_heat_soak",
	"beacon_adaptive_heat_soak_max_wait",
	"beacon_adaptive_heat_soak_extra_wait_after_completion",
	"beacon_adaptive_heat_soak_layer_quality",
	"beacon_adaptive_heat_soak_maximum_first_layer_duration",
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% else %}
	{% set vars = (
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% endif %}
	{% set action = "show" if params|length == 0 else params2.ACTION %}
	{% if action is defined and params|length > 1 %}
	{ action_raise_error("ACTION cannot be specified with other parameters.") }
	{% elif action is not defined %}
	{% for k, v in params2.items() %}
	{% set k = k|lower %}
	{% if k in vars %}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Setting {k} to {v}"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={k} VALUE={v}
	{% else %}
	{ action_raise_error("Parameter '%s' is not recognised. Note that adaptive heatsoaking settings can only be set when a beacon probe is configured." % k) }
	{% endif %}
	{% endfor %}
	{% elif action == "reset" %}
	_RESET_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	CONSOLE_ECHO MSG="Heatsoak settings have been reset to their original values."
	{% elif action == "show" %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% set is_adaptive = False if not has_beacon else current.beacon_adaptive_heat_soak|default("")|lower == "true" %}
	{% if is_adaptive %}
	{% set quality = current.beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set first_layer_duration_secs = current.beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."
	{% elif current.bed_heat_soak_time|default(0)|int > 0 %}
	{% set duration_mins = (current.bed_heat_soak_time|int / 60.0) %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% else %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% endif %}
	{% if verbose %}
	CONSOLE_ECHO MSG="Detailed settings:"
	_SHOW_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	{% endif %}
	{% else %}
	{ action_raise_error("Action '%s' is not recognised" % action) }
	{% endif %}

[gcode_macro _LED_START_PRINTING]
gcode = 
	_LED_ACTION

[gcode_macro _LED_START_PRINTING_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_PRINTING]
gcode = 
	_LED_ON TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_PAUSE]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_ON]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_OFF]
gcode = 
	_LED_STANDBY

[gcode_macro _LED_LOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_LOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_RUNOUT]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_CLOG]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_UNLOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_UNLOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_DEACTIVATE_TOOLHEAD]
gcode = 
	_LED_OFF TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_STANDBY]
gcode = 
	_LED_STANDBY TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_WAKEUP]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_MOTORS_OFF]
gcode = 
	_LED_STANDBY
	_LED_VAOC_OFF

[gcode_macro _LED_INPUT_SHAPER_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_INPUT_SHAPER_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_BEACON_CALIBRATION_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_VAOC_ON]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=1.0 GREEN=1.0 BLUE=1.0
	{% endif %}

[gcode_macro _LED_VAOC_OFF]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=0.0 GREEN=0.0 BLUE=0.0
	{% endif %}

[gcode_macro _LED_ACTION]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_action %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SUCCESS]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_success %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_HEATING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_heating %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_COOLING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_cooling %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ERROR]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_error %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ON]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_on %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_OFF]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_off %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_STANDBY]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_standby %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}
	
	{% if toolhead >= 0 %}
	{% if printer['neopixel nozzle_led_t%s' % toolhead] is defined  %}
	SET_LED LED={'nozzle_led_t%s' % toolhead} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% else %}
	{% if printer['neopixel nozzle_led_t0'] is defined  %}
	SET_LED LED={'nozzle_led_t0'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% if printer['neopixel nozzle_led_t1'] is defined %}
	SET_LED LED={'nozzle_led_t1'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% endif %}
	
	_USER_LED_SET { rawparams }

[gcode_macro _USER_LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}

[gcode_macro LOAD_FILAMENT]
description = Loads new filament. Note: be careful with PETG, make sure you inspect the tip of your filament before loading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% if filament_name == '' or filament_type == '' %}
	{% set filament_name = 'unknown' %}
	{% set filament_type = 'unknown' %}
	{% endif %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_LOAD_FILAMENT TEMP={temp} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_LOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_LOAD_FILAMENT]
description = Load filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_LOAD_FILAMENT" MSG="TEMP={temp}"
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=load_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	_LOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	
	
	RESTORE_GCODE_STATE NAME=load_state
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament load routine complete, please check that the filament was loaded correctly."

[gcode_macro _IDEX_LOAD_FILAMENT]
description = Load filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament into T{toolhead}..."
	
	DEBUG_ECHO PREFIX="_IDEX_LOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	_LOAD_FILAMENT TOOLHEAD={toolhead} TEMP={temp} AUTOMATED={automated}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="Filament load routine for T{toolhead} complete, please check that the filament was loaded correctly."

[gcode_macro _LOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default(false)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE TOOLHEAD={toolhead}
	_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into hotend.."
	G92 E0
	G0 E{extruder_gear_to_cooling_position_distance} F{extruder_load_speed}
	G92 E0
	M400
	RATOS_ECHO MSG="Filament loaded into hotend."

[gcode_macro _LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set load_speed = printer["gcode_macro T%s" % toolhead].filament_load_speed|float * 60 %}
	{% set filament_loading_nozzle_offset = printer["gcode_macro T%s" % toolhead].filament_loading_nozzle_offset|float %}
	{% set cooling_position_to_nozzle_distance = printer["gcode_macro T%s" % toolhead].cooling_position_to_nozzle_distance|float %}
	{% set purge_after_load = printer["gcode_macro T%s" % toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into nozzle... Please wait!"
	G92 E0
	
	G0 E{cooling_position_to_nozzle_distance + filament_loading_nozzle_offset} F{load_speed}
	G92 E0
	G4 P1000
	_PURGE_FILAMENT	TOOLHEAD={toolhead} E={purge_after_load}
	RATOS_ECHO MSG="Filament loaded into nozzle!"

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"
	
	
	{% set filament_grabbing_length = printer["gcode_macro T%s" % toolhead].filament_grabbing_length|float %}
	{% set filament_grabbing_speed = printer["gcode_macro T%s" % toolhead].filament_grabbing_speed|float %}
	{% set resume_after_insert = true if printer["gcode_macro T%s" % toolhead].resume_after_insert|default(true)|lower == 'true' else false %}
	{% set enable_insert_detection = true if printer["gcode_macro T%s" % toolhead].enable_insert_detection|default(true)|lower == 'true' else false %}
	
	
	{% set current_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	
	{% if enable_insert_detection %}
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="toolhead: {toolhead}, filament_grabbing_length: {filament_grabbing_length}, filament_grabbing_speed: {filament_grabbing_speed}, current_idex_mode: {current_idex_mode}"
	
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	RATOS_ECHO MSG="Filament inserted into T{toolhead}, loading..."
	
	
	FORCE_MOVE STEPPER={'extruder%s' % ('' if toolhead == 0 else toolhead)} DISTANCE={filament_grabbing_length} VELOCITY={filament_grabbing_speed}
	M400
	
	
	{% if printer.pause_resume.is_paused %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% if resume_after_insert %}
	RESUME
	{% endif %}
	{% else %}
	{% if not printer.virtual_sdcard.is_active %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"

[gcode_macro _PURGE_BEFORE_UNLOAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set purge_before_unload = printer["gcode_macro T%s" % toolhead].purge_before_unload|float %}
	
	DEBUG_ECHO PREFIX="_PURGE_BEFORE_UNLOAD" MSG="TOOLHEAD: {toolhead}"
	
	
	{% if purge_before_unload > 0 %}
	G92 E0
	G0 E{purge_before_unload} F300
	G92 E0
	M400
	{% endif %}

[gcode_macro _PURGE_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set e = params.E|int %}
	{% set r = params.R|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_PURGE_FILAMENT" MSG="TOOLHEAD: {toolhead}, E: {e}"
	
	
	{% if e > 0 %}
	
	
	G92 E0
	G0 E{e} F300
	G92 E0
	M400
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={0.4 if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={0.4 if toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * 0.4)}
	{% endif %}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if r > 0 %}
	G92 E0
	G0 E-{r} F300
	G92 E0
	M400
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro _MOVE_TO_LOADING_POSITION]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_MOVE_TO_LOADING_POSITION" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	
	G1 X{loading_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _CLEANING_MOVE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_CLEANING_MOVE" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].parking_position is defined and printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set parking_position = printer["gcode_macro T%s" % toolhead].parking_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	{% set cleaning_position = loading_position %}
	{% if loading_position == parking_position %}
	{% if loading_position > 0 %}
	{% set cleaning_position = loading_position - 30 %}
	{% else %}
	{% set cleaning_position = loading_position + 30 %}
	{% endif %}
	{% endif %}
	
	
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _BED_MESH_SANITY_CHECK]
gcode = 
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is defined %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_start_print_true_zero_fuzzy_position %}
	CONSOLE_ECHO TYPE="error" TITLE="Defined zero reference not compatible with fuzzy true zero" MSG="Using fuzzy start print true zero position is not compatible with a defined zero_reference_position value in the [bed_mesh] section in printer.cfg._N_Please remove the zero_reference_position value from the [bed_mesh] section, or disable fuzzy true zero position in printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_start_print_true_zero_fuzzy_position: False"
	_STOP_AND_RAISE_ERROR MSG="Defined zero reference not compatible with fuzzy true zero"
	{% elif zero_ref_pos[0]|float|round != safe_home_x|float|round or zero_ref_pos[1]|float|round != safe_home_y|float|round %}
	CONSOLE_ECHO TYPE="error" TITLE="Zero reference position does not match safe home position" MSG="Please update your bed mesh zero reference position in printer.cfg, like so:_N__N_[bed_mesh]_N_zero_reference_position: {safe_home_x|float|round},{safe_home_y|float|round}_N_"
	_STOP_AND_RAISE_ERROR MSG="Zero reference position does not match safe home position"
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_bed_mesh %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact bed mesh is enabled" MSG="Beacon contact bed mesh is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_bed_mesh: False"
	{% endif %}
	
	{% if beacon_scan_method_automatic %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon 'automatic' scan method is enabled" MSG="Beacon 'automatic' scan method is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_scan_method_automatic: False"
	{% endif %}
	
	{% if beacon_contact_z_tilt_adjust %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact z-tilt adjust is enabled" MSG="Beacon contact z-tilt adjust is enabled. This is not recommended for normal use and may result in inaccurate z-tilt adjustment._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_z_tilt_adjust: False"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH]
gcode = 
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE=None
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE=None
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION {rawparams}
	{% endif %}

[gcode_macro _START_PRINT_BED_MESH]
variable_actual_true_zero_position_x = None
variable_actual_true_zero_position_y = None
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set X=[params.X0|default(-1)|float, params.X1|default(-1)|float] %}
	{% set Y=[params.Y0|default(-1)|float, params.Y1|default(-1)|float] %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_BED_MESH" MSG="idex_mode: {idex_mode}, X: {X}, Y: {Y}"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is not defined %}
	{% set zero_ref_pos = [safe_home_x if actual_true_zero_position_x is none else actual_true_zero_position_x, safe_home_y if actual_true_zero_position_y is none else actual_true_zero_position_y] %}
	{% endif %}
	
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	
	
	
	
	{% set X=[0, printable_x_max] %}
	{% endif %}
	
	
	{% set beacon_bed_mesh_scv = printer["gcode_macro RatOS"].beacon_bed_mesh_scv|default(25)|int %}
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% if printer.fastconfig.settings.beacon is defined and not beacon_contact_bed_mesh %}
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={beacon_bed_mesh_scv}
	{% endif %}
	
	
	{% set default_profile = printer["gcode_macro RatOS"].bed_mesh_profile|default('ratos') %}
	{% if printer["gcode_macro RatOS"].calibrate_bed_mesh|lower == 'true' %}
	BED_MESH_CLEAR
	{% if printer["gcode_macro RatOS"].adaptive_mesh|lower == 'true' %}
	CALIBRATE_ADAPTIVE_MESH PROFILE="{default_profile}" X0={X[0]} X1={X[1]} Y0={Y[0]} Y1={Y[1]} T={params.T|int} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={idex_mode} ZERO_REF_POS_X={zero_ref_pos[0]} ZERO_REF_POS_Y={zero_ref_pos[1]}
	{% else %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	BED_MESH_PROFILE LOAD="{default_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	
	{% elif printer["gcode_macro RatOS"].bed_mesh_profile is defined %}
	BED_MESH_CLEAR
	BED_MESH_PROFILE LOAD="{printer["gcode_macro RatOS"].bed_mesh_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"

[gcode_macro CALIBRATE_ADAPTIVE_MESH]
gcode = 
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set default_profile = params.PROFILE %}
	
	
	{% set x0 = params.X0|default(-1)|float %}
	{% set y0 = params.Y0|default(-1)|float %}
	{% set x1 = params.X1|default(-1)|float %}
	{% set y1 = params.Y1|default(-1)|float %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Received coordinates X0={x0|round(1)} Y0={y0|round(1)} X1={x1|round(1)} Y1={y1|round(1)}"
	
	{% if x0 >= x1 or y0 >= y1 %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Invalid coordinates received. Please check your slicer settings. Falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	
	
	{% if params.ZERO_REF_POS_X is defined and params.ZERO_REF_POS_Y is defined %}
	{% set zero_ref_pos_x = params.ZERO_REF_POS_X|float %}
	{% set zero_ref_pos_y = params.ZERO_REF_POS_Y|float %}
	{% if zero_ref_pos_x < x0 or zero_ref_pos_x > x1 or zero_ref_pos_y < y0 or zero_ref_pos_y > y1 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Zero reference position X={zero_ref_pos_x|round(1)} Y={zero_ref_pos_y|round(1)} is outside the mesh region, expanding mesh region to include it."
	{% set x0 = [x0, zero_ref_pos_x]|min %}
	{% set y0 = [y0, zero_ref_pos_y]|min %}
	{% set x1 = [x1, zero_ref_pos_x]|max %}
	{% set y1 = [y1, zero_ref_pos_y]|max %}
	{% endif %}
	{% endif %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float %}
	
	
	{% set mesh_x0 = [[x0, max_x]|min, min_x]|max %}
	{% set mesh_y0 = [[y0, max_y]|min, min_y]|max %}
	{% set mesh_x1 = [[x1, max_x]|min, min_x]|max %}
	{% set mesh_y1 = [[y1, max_y]|min, min_y]|max %}
	
	{% if mesh_x0 == min_x and mesh_y0 == min_y and mesh_x1 == max_x and mesh_y1 == max_y %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Print is using the full bed, falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	
	{% set probe_count_x = mesh_config.probe_count.split(",")[0]|int %}
	{% if mesh_config.probe_count.split(",")|length == 2 %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[1]|int %}
	{% else %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[0]|int %}
	{% endif %}
	
	
	{% set probe_x_step = (max_x - min_x) / probe_count_x %}
	{% set probe_y_step = (max_y - min_y) / probe_count_y %}
	
	
	{% set mesh_count_x = ([(mesh_x1 - mesh_x0) / probe_x_step, 3]|max)|int %}
	{% set mesh_count_y = ([(mesh_y1 - mesh_y0) / probe_y_step, 3]|max)|int %}
	{% set min_mesh_count = [mesh_count_x, mesh_count_y]|min %}
	{% set max_mesh_count = [mesh_count_x, mesh_count_y]|max %}
	
	
	{% set algorithm = mesh_config.algorithm %}
	{% if algorithm|lower == 'lagrange' and max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="cannot exceed a probe_count of 6 when using lagrange interpolation. Falling back to bicubic interpolation."
	{% set algorithm = 'bicubic' %}
	{% endif %}
	{% if algorithm|lower == 'bicubic' and min_mesh_count < 4 %}
	{% if max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="invalid probe_count option when using bicubic interpolation. Combination of 3 points on one axis with more than 6 on another is not permitted. Forcing minimum mesh count to be 4."
	{% set min_mesh_count = 4 %}
	{% else %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="bicubic interpolation with a probe_count of less than 4 points detected. Forcing lagrange interpolation."
	{% set algorithm = 'lagrange' %}
	{% endif %}
	{% endif %}
	
	{% set mesh_count_x = ([min_mesh_count, mesh_count_x]|max)|int %}
	{% set mesh_count_x = ([max_mesh_count, mesh_count_x]|min)|int %}
	{% set mesh_count_y = ([min_mesh_count, mesh_count_y]|max)|int %}
	{% set mesh_count_y = ([max_mesh_count, mesh_count_y]|min)|int %}
	
	{% set should_prime = printer["gcode_macro RatOS"].nozzle_priming == 'primeblob' %}
	{% if printer["dual_carriage"] is not defined %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% else %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 != 0 and probe_first %}
	{% set probe_first = false %}
	{% elif printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 == 0 and not probe_first %}
	{% set probe_first = true %}
	{% endif %}
	
	
	{% if should_prime and probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="mesh coordinates X0={mesh_x0|round(1)} Y0={mesh_y0|round(1)} X1={mesh_x1|round(1)} Y1={mesh_y1|round(1)}"
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y} RELATIVE_REFERENCE_INDEX=-1
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	
	
	{% if should_prime and not probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro M84]
rename_existing = M84.1
gcode = 
	
	M84.1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_OFFSET X=0 Y=0
	
	
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro _VAOC"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False
	{% endif %}
	
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	SET_SKEW CLEAR=1
	
	
	_LED_MOTORS_OFF

[gcode_macro M104]
rename_existing = M104.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M104" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set temperature_offset_t0 = printer["gcode_macro T0"].temperature_offset|default(0)|int %}
	{% set temperature_offset_t1 = printer["gcode_macro T1"].temperature_offset|default(0)|int %}
	{% set s0 = [s + temperature_offset_t0, 0]|max %}
	{% set s1 = [s + temperature_offset_t1, 0]|max %}
	{% if temperature_offset_t0 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t0}°C added to toolhead T0."
	{% endif %}
	{% if temperature_offset_t1 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t1}°C added to toolhead T1."
	{% endif %}
	{% else %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	M104.1 S{s0} T0
	M104.1 S{s1} T1
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% else %}
	M104.1 S{s} T{t}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M109]
rename_existing = M109.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M109" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M109" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	M109.1 S{s} T{t}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro SET_HEATER_TEMPERATURE]
rename_existing = SET_HEATER_TEMPERATURE_BASE
gcode = 
	
	{% set heater = params.HEATER|default("") %}
	{% set target = params.TARGET|default(0)|int %}
	
	DEBUG_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="heater: {heater}, target: {target}"
	
	{% set t = -1 %}
	{% if heater|lower == "extruder" or heater|lower == "extruder1" %}
	
	{% set t = 0 if heater|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and target > 0 %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set target = [target + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE_BASE HEATER="{heater}" TARGET={target}
	
	{% if t != -1 and printer.fastconfig.settings.beacon is defined %}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro TEMPERATURE_WAIT]
rename_existing = TEMPERATURE_WAIT_BASE
gcode = 
	
	{% set sensor = params.SENSOR|default("") %}
	{% set minimum = params.MINIMUM|default(-1)|int %}
	{% set maximum = params.MAXIMUM|default(-1)|int %}
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="sensor: {sensor}, minimum: {minimum}, maximum: {maximum}"
	
	{% set t = -1 %}
	{% if sensor|lower == "extruder" or sensor|lower == "extruder1" %}
	
	{% set t = 0 if sensor|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and (minimum > 0 or maximum > 0) %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% if minimum > -1 %}
	{% set minimum = [minimum + temperature_offset, 0]|max %}
	{% endif %}
	{% if maximum > -1 %}
	{% set maximum = [maximum + temperature_offset, 0]|max %}
	{% endif %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set id = "sensor " ~ sensor if t == -1 else "toolhead T" ~ t %}
	
	
	{% if minimum > -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum} MAXIMUM={maximum}
	{% elif minimum > -1 and maximum == -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum}
	{% elif minimum == -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MAXIMUM={maximum}
	{% else %}
	
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="neither MINIMUM or MAXIMUM args were specified, call TEMPERATURE_WAIT_BASE is expected to fail"
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}"
	{% endif %}
	
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature for {id} reached."

[gcode_macro SDCARD_PRINT_FILE]
rename_existing = SDCARD_PRINT_FILE_BASE
gcode = 
	{% if printer["ratos"] is defined %}
	PROCESS_GCODE_FILE { rawparams }
	{% else %}
	SDCARD_PRINT_FILE_BASE { rawparams }
	{% endif %}

[gcode_macro SKEW_PROFILE]
rename_existing = SKEW_PROFILE_BASE
variable_loaded_profile = ""
gcode = 
	{% if params.LOAD is defined %}
	{% if printer.fastconfig.settings["skew_correction %s" % params.LOAD] is defined %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='"{params.LOAD}"'
	{% endif %}
	{% endif %}
	
	SKEW_PROFILE_BASE { rawparams }

[gcode_macro SET_SKEW]
rename_existing = SET_SKEW_BASE
gcode = 
	{% if params.CLEAR is defined %}
	{% if params.CLEAR|default(0)|int == 1 %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='""'
	{% endif %}
	{% endif %}
	
	SET_SKEW_BASE { rawparams }

[gcode_macro SET_VELOCITY_LIMIT]
rename_existing = SET_VELOCITY_LIMIT_BASE
gcode = 
	{% if params.ACCEL_TO_DECEL is defined %}
	
	{% if params.ACCEL is defined %}
	{% set accel = params.ACCEL|float %}
	{% else %}
	{% set accel = printer.toolhead.max_accel|float %}
	{% endif %}
	
	{% if params.VELOCITY is defined %}
	{% set velocity = params.VELOCITY|float %}
	{% else %}
	{% set velocity = printer.toolhead.max_velocity|float %}
	{% endif %}
	
	{% if params.SQUARE_CORNER_VELOCITY is defined %}
	{% set scv = params.SQUARE_CORNER_VELOCITY|float %}
	{% else %}
	{% set scv = printer.toolhead.square_corner_velocity|float %}
	{% endif %}
	
	{% set mcr = params.ACCEL_TO_DECEL|float / accel %}
	
	DEBUG_ECHO PREFIX="SET_VELOCITY_LIMIT" MSG="ACCEL={accel}, VELOCITY={velocity}, SQUARE_CORNER_VELOCITY={scv}, MINIMUM_CRUISE_RATIO={mcr}"
	
	SET_VELOCITY_LIMIT_BASE ACCEL={accel} VELOCITY={velocity} SQUARE_CORNER_VELOCITY={scv} MINIMUM_CRUISE_RATIO={1-mcr}
	
	{% else %}
	
	SET_VELOCITY_LIMIT_BASE { rawparams }
	
	{% endif %}

[gcode_macro BED_MESH_CALIBRATE]
rename_existing = _BED_MESH_CALIBRATE_BASE
variable_abl_and_home_z_if_required = True
gcode = 
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	{% if abl_and_home_z_if_required %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% endif %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set beacon_default_probe_method = printer.fastconfig.settings.beacon.default_probe_method|default('proximity') %}
	{% set probe_method = params.PROBE_METHOD|default(beacon_default_probe_method)|lower %}
	{% if probe_method == 'proximity' %}
	_CHECK_ACTIVE_BEACON_MODEL_TEMP TITLE="Bed mesh calibration warning"
	{% endif %}
	{% endif %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_BED_MESH_CALIBRATE_BASE {rawparams}
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	_APPLY_RATOS_BED_MESH_PARAMETERS {rawparams}
	{% endif %}

[gcode_macro SET_GCODE_OFFSET]
rename_existing = SET_GCODE_OFFSET_BASE
gcode = 
	DEBUG_ECHO PREFIX="SET_GCODE_OFFSET" MSG="{rawparams|replace('"', '')|replace("'", '')}"
	{% set z_before = printer.gcode_move.homing_origin.z|float %}
	SET_GCODE_OFFSET_BASE {rawparams}
	_AFTER_SET_GCODE_OFFSET Z_BEFORE={z_before}

[gcode_macro _AFTER_SET_GCODE_OFFSET]
gcode = 
	{% set z_before = params.Z_BEFORE|float %}
	{% set z_after = printer.gcode_move.homing_origin.z|float %}
	{% if z_before != z_after %}
	_ALERT_NON_ZERO_Z_OFFSET FORCE=1
	{% endif %}

[gcode_macro _START_PRINT_PARK]
gcode = 
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_x = printer["gcode_macro RatOS"].start_print_park_x %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% if printer["gcode_macro RatOS"].start_print_park_x is defined and printer["gcode_macro RatOS"].start_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="start_print_park_x is ignored for IDEX printers"
	{% endif %}
	PARK_TOOLHEAD
	G90
	{% endif %}
	
	
	_PARK LOCATION={start_print_park_in} X={start_print_park_x}
	G0 Z{z} F{z_speed}

[gcode_macro _END_PRINT_PARK]
gcode = 
	{% if printer["dual_carriage"] is defined %}
	
	{% if printer["gcode_macro RatOS"].end_print_park_x is defined and printer["gcode_macro RatOS"].end_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="end_print_park_x is ignored for IDEX printers"
	{% endif %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	PARK_TOOLHEAD
	G90
	{% endif %}
	_PARK LOCATION={printer["gcode_macro RatOS"].end_print_park_in} X={printer["gcode_macro RatOS"].end_print_park_x}

[gcode_macro _PARK]
gcode = 
	
	{% set x = params.X %}
	{% set location = params.LOCATION|default('back')|lower %}
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	{% set nozzle_priming = printer["gcode_macro RatOS"].nozzle_priming|lower %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="park"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% if x != '' %}
	{% if x|float >= printer.toolhead.axis_minimum.x + 5 and x|float <= printable_x_max - 5 %}
	{% set park_x = x|float %}
	{% else %}
	{action_respond_info('The requested X co-ordinate is outside the defined axis bounds - using defaults')}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	{% else %}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	
	
	{% set park_y = printable_y_max - 15 %}
	{% if location == 'front' %}
	{% set park_y = printer.toolhead.axis_minimum.y + 5 %}
	{% elif location == 'center' %}
	{% set park_y = printable_y_max / 2 %}
	{% elif location == 'primeblob' and printer["dual_carriage"] is defined %}
	
	{% set park_y = printable_y_max - 15 %}
	{% endif %}
	
	
	{% if location == 'primeblob' and printer["dual_carriage"] is not defined %}
	{% if (nozzle_priming == 'primeblob' or nozzle_priming == 'primeline') %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set park_x = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set park_x = printable_x_max - 5 %}
	{% else %}
	{% set park_x = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set park_y = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set park_y = printable_y_max - 5 %}
	{% else %}
	{% set park_y = nozzle_prime_start_y|float %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	G0 X{park_x} Y{park_y} F{speed}
	{% else %}
	
	G0 Y{park_y} F{speed}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="park"

[gcode_macro SAVE_PROBE_RESULT]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	{% set last_z_offset = 9999.9 %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if beacon_contact_prime_probing %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	{% else %}
	{% set last_z_offset = printer.beacon.last_sample.dist - current_z %}
	{% endif %}
	{% elif printer.fastconfig.settings.bltouch is defined  %}
	{% set config_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% elif printer.fastconfig.settings.probe is defined  %}
	{% set config_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% endif %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Saving offset adjustment of {last_z_offset} in {params.VARIABLE|default('last_z_offset')}"
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={params.VARIABLE|default('last_z_offset')} VALUE={last_z_offset}

[gcode_macro PROBE_FOR_PRIMING]
gcode = 
	
	{% set probe_for_priming_disable_mesh_constraints = true if printer["gcode_macro RatOS"].probe_for_priming_disable_mesh_constraints|default(false)|lower == 'true' else false %}
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower != 'false' %}
	SAVE_GCODE_STATE NAME=probe_for_priming_state
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the prime location.."
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set t = params.TOOLHEAD|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% if idex_mode == '' %}
	
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% if t == 0 %}
	{% set x_start = 5 %}
	{% else %}
	{% set x_start = printable_x_max - 5 %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% endif %}
	{% endif %}
	{% set z = printer.fastconfig.settings.bed_mesh.horizontal_move_z|float %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% if printer.fastconfig.settings.bltouch is defined %}
	{% set x_offset = printer.fastconfig.settings.bltouch.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.bltouch.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% elif printer.fastconfig.settings.probe is defined %}
	{% set x_offset = printer.fastconfig.settings.probe.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.probe.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% elif printer.fastconfig.settings.beacon is defined %}
	{% set x_offset = printer.fastconfig.settings.beacon.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.beacon.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.beacon.trigger_distance|float %}
	{% else %}
	{ action_raise_error("No probe, beacon or bltouch section found. Adaptive priming only works with a [probe], [beacon] or [bltouch] section defined.") }
	{% endif %}
	
	{% if z < z_offset %}
	{ action_raise_error("Horizontal move Z ({z}) is below your probe's Z offset ({z_offset}). Please adjust your horizontal_move_z setting in [bed_mesh] to be above {z}.") }
	{% endif %}
	
	{% if not probe_for_priming_disable_mesh_constraints %}
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float - x_offset %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float - y_offset %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float - x_offset %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float - y_offset %}
	
	
	{% set x_start = [[x_start, max_x]|min, min_x]|max %}
	{% set y_start = [[y_start, max_y]|min, min_y]|max %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the start of the prime location at {x_start}, {y_start}"
	
	G90
	
	M83
	
	G0 Z{z} F{z_speed}
	
	G1 X{x_start} Y{y_start} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result
	{% endif %}
	
	{% if idex_mode == '' %}
	
	{% set x_end = x_start %}
	{% set y_end = y_start + 45 %}
	{% else %}
	
	{% if t==1 %}
	{% set x_end = x_start - 45 %}
	{% else %}
	{% set x_end = x_start + 45 %}
	{% endif %}
	{% set y_end = y_start %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the end of the prime location at {x_end}, {y_end}"
	G1 X{x_end} Y{y_end} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result
	{% endif %}
	
	RESTORE_GCODE_STATE NAME=probe_for_priming_state
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	{% endif %}

[gcode_macro RESET_PRIME_PROBE_STATE]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result VALUE=None
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result_t1 VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result_t1 VALUE=None
	{% endif %}

[gcode_macro PROBE_CURRENT_POSITION]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	SAVE_GCODE_STATE NAME=probe_current_position_state
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	ASSERT_PROBE_DEPLOYED
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_prime_probing %}
	PROBE PROBE_METHOD=contact SAMPLES=1
	{% else %}
	PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	BEACON_QUERY
	{% else %}
	
	RESTORE_GCODE_STATE NAME=probe_current_position_state MOVE=1 MOVE_SPEED={printer["gcode_macro RatOS"].macro_z_speed|float}
	{% endif %}

[gcode_macro PRIME_BLOB]
description = Prints a primeblob, used internally, if configured, as part of the START_PRINT macro.
variable_x_offset = 5
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="prime_blob"
	SET_MACRO_TRAVEL_SETTINGS
	
	RATOS_ECHO PREFIX="Priming" MSG="Priming nozzle with prime blob.."
	
	
	{% set current_toolhead = 0 %}
	
	
	{% set target_idex_mode = '' %}
	{% set extruder = 'extruder' %}
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE is defined %}
	{% set target_idex_mode = params.IDEX_MODE|default('')|lower %}
	{% else %}
	{ action_raise_error("IDEX_MODE parameter not found for PRIME_BLOB macro. This is likely a bug.") }
	{% endif %}
	RATOS_ECHO PREFIX="Priming" MSG="Priming in IDEX {target_idex_mode} mode.."
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set current_toolhead = 1 if current_idex_mode=='primary' else 0 %}
	{% set extruder = 'extruder1' if current_toolhead == 1 else 'extruder' %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	SAVE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set fan_speed = printer["gcode_macro RatOS"].nozzle_prime_bridge_fan|float %}
	{% set nozzle_diameter = printer.fastconfig.settings[extruder].nozzle_diameter|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set has_start_offset_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) != 9999.9 %}
	{% if printer["dual_carriage"] is defined %}
	{% set has_start_offset_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) != 9999.9 %}
	{% endif %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_z_height = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set nozzle_prime_direction = printer["gcode_macro RatOS"].nozzle_prime_direction|lower %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% if target_idex_mode == '' %}
	
	{% set x_factor = 0 %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% set y_factor = -1 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% if nozzle_prime_start_y|float < printable_y_max / 2 %}
	{% set y_factor = 1 %}
	{% else %}
	{% set y_factor = -1 %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_direction == 'forwards' %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_direction == 'backwards' %}
	{% set y_factor = -1 %}
	{% endif %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% else %}
	{% set z = start_print_park_z_height %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% set y_factor = 0 %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set x_start = center_x / 2 + 5 %}
	{% set x_factor = 1 %}
	{% else %}
	
	
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% if current_toolhead == 0 %}
	{% set x_start = 55 %}
	{% set x_factor = -1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 55 %}
	{% set x_factor = 1 %}
	{% endif %}
	{% else %}
	{% if current_toolhead == 0 %}
	{% set x_start = 5 %}
	{% set x_factor = 1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 5 %}
	{% set x_factor = -1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_x_max - 5 %}
	{% endif %}
	{% set z = 10 %}
	{% endif %}
	
	{% set start_z_offset = 0 %}
	{% set end_z_offset = 0 %}
	{% if has_start_offset_t0 %}
	{% set start_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) %}
	{% set end_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_end_result|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t0) ) }
	{% endif %}
	{% if end_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t0) )  }
	{% endif %}
	{% set start_z_offset = start_z_probe_result_t0 %}
	{% set end_z_offset = end_z_probe_result_t0 %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	{% if current_toolhead == 1 or both_toolheads or target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	{% if has_start_offset_t1 %}
	{% set start_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) %}
	{% set end_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_end_result_t1|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t1) ) }
	{% endif %}
	{% if end_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t1) ) }
	{% endif %}
	{% set start_z_offset = [start_z_offset, start_z_probe_result_t1]|max %}
	{% set end_z_offset = [end_z_offset, start_z_probe_result_t1]|max %}
	{% endif %}
	{% endif %}
	{% if target_idex_mode != 'copy' and target_idex_mode != 'mirror' %}
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% set original_start_z_offset = start_z_offset %}
	{% set original_end_z_offset = end_z_offset %}
	{% set start_z_offset = original_end_z_offset %}
	{% set end_z_offset = original_start_z_offset %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	DEBUG_ECHO PREFIX="PRIME_BLOB" MSG="x_start: {x_start}, y_start: {y_start}, x_factor: {x_factor}, y_factor: {y_factor}, z: {z}, start_z_offset: {start_z_offset}, end_z_offset: {end_z_offset}"
	
	
	G90
	
	M83
	RATOS_ECHO PREFIX="Priming" MSG="Lifting Z to {z}.."
	
	G0 Z{z} F{z_speed}
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% if start_print_park_in != 'primeblob' %}
	G1 X{x_start} F{speed}
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% endif %}
	{% else %}
	
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% if target_idex_mode=="copy" or target_idex_mode=="mirror" %}
	RATOS_ECHO PREFIX="Priming" MSG="Mirroring move to {x_start}, {y_start} along the edge of the print area.."
	
	_IDEX_MIRROR PRIMING=1
	{% else %}
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% endif %}
	G1 X{x_start} F{speed}
	{% endif %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Starting prime blob.."
	
	G1 Z{0.5 + start_z_offset} F{z_speed}
	
	G1 Y{y_start} F{speed}
	
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	
	M106 S{fan_speed}
	
	G1 Z5 F100 E5
	G92 E0
	RATOS_ECHO PREFIX="Priming" MSG="Bridging with {((fan_speed/255) * 100)|int}% fan speed.."
	
	G1 F3000 X{x_start + (15 * x_factor)} Y{y_start + (15 * y_factor)} E{1 / ((0.4 / nozzle_diameter) ** 2)}
	
	
	
	G1 F3000 X{x_start + (20 * x_factor)} Y{y_start + (20 * y_factor)} Z{3.8 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (34 * x_factor)} Y{y_start + (34 * y_factor)} Z{2.6 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (38 * x_factor)} Y{y_start + (38 * y_factor)} Z{1.4 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (42 * x_factor)} Y{y_start + (42 * y_factor)} Z{0.2 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	
	M106 S0
	
	G1 F3000 X{x_start + (46 * x_factor)} Y{y_start + (46 * y_factor)} Z{0.2 + end_z_offset} E0.6
	
	G1 F{speed} X{x_start + (50 * x_factor)} Y{y_start + (50 * y_factor)}
	
	
	{% if target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if target_idex_mode == "copy" %}
	{% if first_y >= 0 %}
	_IDEX_COPY DANCE=0 Y={first_y}
	{% else %}
	_IDEX_COPY DANCE=0 Y={params.Y1}
	{% endif %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	RESTORE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="prime_blob"
	
	
	G92 E0

[gcode_macro UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set temp = params.TEMP|default(220)|int %}
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_UNLOAD_FILAMENT TEMP={temp} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_UNLOAD_FILAMENT]
description = Unload filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_UNLOAD_FILAMENT" MSG="TEMP: {temp}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=unload_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	G4 P3000
	
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD=0 NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=unload_state
	
	
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament unloading completed"

[gcode_macro _IDEX_UNLOAD_FILAMENT]
description = Unload filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading T{toolhead} filament..."
	
	DEBUG_ECHO PREFIX="_IDEX_UNLOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} AUTOMATED={automated}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="T{toolhead} filament unloading completed"

[gcode_macro _UNLOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LEGACY_UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
gcode = 
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set unload_speed = 5 * 60 %}
	{% set unload_length = printer["gcode_macro RatOS"].filament_unload_length|float %}
	M117 Unloading filament...
	
	G0 E10 F300
	
	G0 E-5 F3600
	
	G4 P3000
	
	G0 E5 F6000
	
	G0 E-15 F6000
	
	G0 E-{unload_length} F{unload_speed}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}
	M117 Filament unloaded!
	RESPOND MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	RATOS_ECHO MSG="Unloading filament from nozzle to cooling zone... Please wait!"
	
	_PURGE_BEFORE_UNLOAD TOOLHEAD={toolhead}
	
	{% if printer["gcode_macro _UNLOAD_WITHOUT_TIP_FORMING"] is defined %}
	
	_UNLOAD_WITHOUT_TIP_FORMING TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	_UNLOAD_WITH_TIP_FORMING NAME='{filament_name}' TYPE='{filament_type}'
	{% endif %}
	
	G4 P3000

[gcode_macro _UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	{% set tooolhead_sensor_to_extruder_gear_distance = printer["gcode_macro T%s" % toolhead].tooolhead_sensor_to_extruder_gear_distance|float %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER" MSG="TOOLHEAD: {toolhead}"
	
	
	G0 E-{extruder_gear_to_cooling_position_distance + tooolhead_sensor_to_extruder_gear_distance + 50} F{extruder_load_speed}
	
	RATOS_ECHO MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_WITH_TIP_FORMING]
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	{% if filament_name != '' and filament_type != '' %}
	_UNLOAD_KNOWN_FILAMENT NAME={filament_name} TYPE={filament_type}
	{% else %}
	_UNLOAD_UNKNOWN_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _UNLOAD_KNOWN_FILAMENT]
description = User overrideable tip forming macro if slicer filament profiles are known
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	RATOS_ECHO PREFIX="FILAMENT TYPE" MSG='{filament_type}'
	RATOS_ECHO PREFIX="FILAMENT PROFILE" MSG='{filament_name}'
	
	
	{% if filament_name == "Prusament PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% elif filament_name == "Nobufil PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% else %}
	
	RATOS_ECHO PREFIX="_UNLOAD_KNOWN_FILAMENT" MSG="Filament profile not found!"
	_UNLOAD_UNKNOWN_FILAMENT
	{% endif %}

[gcode_macro _UNLOAD_UNKNOWN_FILAMENT]
description = User overrideable standard tip forming macro
gcode = 
	
	DEBUG_ECHO PREFIX="_UNLOAD_UNKNOWN_FILAMENT" MSG="Using standard tip forming macro!"
	
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10

[gcode_macro _TIP_FORMING]
gcode = 
	
	{% set cooling_moves = params.COOLING_MOVES|default(4)|int %}
	{% set cooling_move_length = params.COOLING_MOVE_LENGTH|default(10)|float %}
	{% set start_cooling_speed = params.START_COOLING_SPEED|default(10)|float * 60 %}
	{% set end_cooling_speed = params.END_COOLING_SPEED|default(50)|float * 60 %}
	{% if cooling_moves == 0 %}
	{% set cooling_move_length = 0 %}
	{% endif %}
	
	
	{% set dip = true if params.DIP|default(false)|lower == "true" else false %}
	{% set dip_length = params.DIP_LENGTH|default(22)|float %}
	{% set dip_speed = params.DIP_SPEED|default(30)|float * 60 %}
	{% set dip_retract_speed = params.DIP_RETRACT_SPEED|default(70)|float * 60 %}
	
	
	{% set retract_length = params.RETRACT_LENGTH|default(18)|float %}
	{% set start_retract_speed = params.START_RETRACT_SPEED|default(120)|float * 60 %}
	{% set end_retract_speed = params.END_RETRACT_SPEED|default(20)|float * 60 %}
	
	DEBUG_ECHO PREFIX="_TIP_FORMING" MSG="cooling_moves: {cooling_moves}, cooling_move_length: {cooling_move_length}, start_cooling_speed: {start_cooling_speed}, end_cooling_speed: {end_cooling_speed}, dip: {dip}, dip_length: {dip_length}, dip_speed: {dip_speed}, dip_retract_speed: {dip_retract_speed}, retract_length: {retract_length}, start_retract_speed: {start_retract_speed}, end_retract_speed: {end_retract_speed}"
	
	M220 S100
	
	
	G92 E0
	{% set retract = retract_length + cooling_move_length / 2 - 15 %}
	G1 E-15 F{start_retract_speed}
	G1 E-{0.7 * retract} F{1.0 * end_retract_speed}
	G1 E-{0.2 * retract} F{0.5 * end_retract_speed}
	G1 E-{0.1 * retract} F{0.3 * end_retract_speed}
	
	
	G92 E0
	{% if cooling_moves > 0 %}
	{% set i = (end_cooling_speed - start_cooling_speed) / (2 * cooling_moves - 1) %}
	{% for m in range(cooling_moves) %}
	G1 E{cooling_move_length} F{(start_cooling_speed + i * m * 2)}
	G1 E-{cooling_move_length} F{(start_cooling_speed + i * (m * 2 + 1))}
	{% endfor %}
	{% endif %}
	
	
	G92 E0
	{% if dip %}
	G1 E{dip_length} F{dip_speed}
	G4 P100
	G1 E-{dip_length} F{dip_retract_speed}
	{% endif %}
	
	G92 E0
	M400

[delayed_gcode __ON_FILAMENT_SENSOR_BUTTON_PRESSED_STARTUP_GUARD]
initial_duration = 2.
gcode = 
	SET_GCODE_VARIABLE MACRO=_ON_FILAMENT_SENSOR_BUTTON_PRESSED VARIABLE=startup_complete VALUE=True

[gcode_macro _ON_FILAMENT_SENSOR_BUTTON_PRESSED]
variable_startup_complete = False
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set toolhead_sensor_button_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_sensor_button_only_when_sensor_enabled|default(false)|lower == 'true' %}
	
	
	{% if not startup_complete and sensor_enabled %}
	{action_emergency_stop("RatOS: The T%s filament sensor button was triggered immediately on printer startup. This is likely a false trigger. Please check your filament sensor wiring and configuration!" % (toolhead,))}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_SENSOR_BUTTON_PRESSED" MSG="TOOLHEAD: {toolhead}, SENSOR_ENABLED: {sensor_enabled}, TOOLHEAD_SENSOR_BUTTON_ONLY_WHEN_SENSOR_ENABLED: {toolhead_sensor_button_only_when_sensor_enabled}"
	
	{% if not printer.virtual_sdcard.is_active and (sensor_enabled or not toolhead_sensor_button_only_when_sensor_enabled) %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	{% set toolhead_detect_clog_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_detect_clog_only_when_sensor_enabled|default(true)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}, ENABLE_CLOG_DETECTION: {enable_clog_detection}, TOOLHEAD_DETECT_CLOG_ONLY_WHEN_SENSOR_ENABLED: {toolhead_detect_clog_only_when_sensor_enabled}, SENSOR_ENABLED: {sensor_enabled}"
	
	{% if enable_clog_detection and (sensor_enabled or not toolhead_detect_clog_only_when_sensor_enabled) %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_clog_detection %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_FILAMENT_END]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set clogged = true if params.CLOGGED|default(false)|lower == 'true' else false %}
	
	
	{% set unload_after_runout = printer["gcode_macro T%s" % toolhead].unload_after_runout|float %}
	
	
	{% if clogged %}
	_LED_FILAMENT_CLOG TOOLHEAD={toolhead}
	{% else %}
	_LED_FILAMENT_RUNOUT TOOLHEAD={toolhead}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_END" MSG="TOOLHEAD: {toolhead}"
	
	{% if printer.virtual_sdcard.is_active %}
	{% if not printer.pause_resume.is_paused %}
	PAUSE RUNOUT=True
	{% endif %}
	{% if not clogged and unload_after_runout %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	{% if not clogged and printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true'%}
	_JOIN_SPOOL TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M600]
description = Executes a color change by pausing the printer an unloading the filament.
gcode = 
	PAUSE
	UNLOAD_FILAMENT AUTOMATED=True
	RATOS_ECHO MSG="Please load new filament and resume"

[gcode_macro COLD_PULL]
description = Automated hotend cold pull.
gcode = 
	
	{% set extrusion_temp = params.EXTRUSION_TEMP|default(220)|int %}
	{% set cold_pull_temp = params.COLD_PULL_TEMP|default(80)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	
	{% if printer["dual_carriage"] is not defined %}
	{% set toolhead = 0 %}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead != 0 and toolhead != 1 %}
	{action_raise_error("Please select toolhead! 0 = left, 1 = right toolhead")}
	{% endif %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	RATOS_ECHO MSG="Starting cold pull on T{toolhead}..."
	{% else %}
	RATOS_ECHO MSG="Starting cold pull..."
	{% endif %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	SAVE_GCODE_STATE NAME=cold_pull_state
	
	
	{% if printer["dual_carriage"] is defined and "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	RATOS_ECHO MSG="Heating T{toolhead} to {extrusion_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={extrusion_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={extrusion_temp} MAXIMUM={extrusion_temp + 2}
	
	
	G4 P3000
	
	
	RATOS_ECHO MSG="extruding..."
	G92 E0
	G1 E30 F300
	G92 E0
	
	
	RATOS_ECHO MSG="Cooling T{toolhead} to {cold_pull_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={cold_pull_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={cold_pull_temp} MAXIMUM={cold_pull_temp + 2}
	
	
	G4 P10000
	
	
	RATOS_ECHO MSG="cold pull..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-40 VELOCITY=5 ACCEL=100
	
	
	RATOS_ECHO MSG="eject filament..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-200 VELOCITY=20 ACCEL=500
	
	
	RATOS_ECHO MSG="cooling down extruder..."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	RESTORE_GCODE_STATE NAME=cold_pull_state
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	
	CONSOLE_ECHO TITLE="Cold pull complete" MSG="Please remove the filament from the PTFE tube and cut the end off. Do NOT try to load it again." TYPE="warning"

[gcode_macro _USER_START_PRINT_BEFORE_HOMING]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_BED]
gcode = 

[gcode_macro _USER_START_PRINT_BED_MESH]
gcode = 

[gcode_macro _USER_START_PRINT_PARK]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 

[gcode_macro _USER_START_PRINT_HEAT_CHAMBER]
description = Uses the extruder sensor to wait for chamber temp. Override the _START_PRINT_HEAT_CHAMBER macro to implement heated chamber handling.
gcode = 
	
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}

[gcode_macro _USER_END_PRINT_BEFORE_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_AFTER_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_PARK]
gcode = 

[gcode_macro _USER_END_PRINT_FINISHED]
description = User hook for when the print is finished after gcode state has been restored.
gcode = 

[gcode_macro _USER_START_PRINT]
gcode = 

[gcode_macro _USER_END_START_PRINT]
gcode = 

[gcode_macro _USER_START_FEATURE]
gcode = 

[gcode_macro _USER_END_FEATURE]
gcode = 

[gcode_macro _USER_BEFORE_IDLE_TIMEOUT]
gcode = 

[gcode_macro _USER_AFTER_IDLE_TIMEOUT]
gcode = 

[gcode_macro ECHO_T_VARS]
description = Echo Toolhead variables to the console.
gcode = 
	{% set t = params.T|default(0) %}
	RATOS_ECHO MSG="T{t} Variables"
	{% for var, value in printer["gcode_macro T%s" % t].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ECHO_RATOS_VARS]
description = Echo RatOS variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro RatOS"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ENSURE_CRITICAL_RATOS_INIT]
variable_completed = False
gcode = 
	{% if not completed %}
	CALCULATE_PRINTABLE_AREA
	SET_GCODE_VARIABLE MACRO=ENSURE_CRITICAL_RATOS_INIT VARIABLE=completed VALUE=True
	{% endif %}

[delayed_gcode RATOS_INIT]
initial_duration = 0.1
gcode = 
	{action_respond_info("Initializing RatOS...")}
	ENSURE_CRITICAL_RATOS_INIT
	_LED_STANDBY
	INITIAL_FRONTEND_UPDATE
	_CHAMBER_FILTER_SANITY_CHECK
	{% if printer.fastconfig.settings.beacon is defined %}
	
	_BED_MESH_SANITY_CHECK
	{% endif %}
	{% set svv = printer.save_variables.variables %}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=0 C={svv.nozzle_expansion_coefficient_t0|default(0.06)|float}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=1 C={svv.nozzle_expansion_coefficient_t1|default(0.06)|float}
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=idex_applied_offset

[delayed_gcode RATOS_LOGO]
initial_duration = 2
gcode = 
	
	
	
	
	
	ENSURE_CRITICAL_RATOS_INIT
	HELLO_RATOS
	_ALERT_NON_ZERO_Z_OFFSET

[gcode_macro _ALERT_NON_ZERO_Z_OFFSET]
gcode = 
	{% set force = params.FORCE|default(0)|int == 1 %}
	{% set user_offset = printer.named_offsets.user_probe_z_offset.z|float %}
	{% set gcode_offset = printer.gcode_move.homing_origin.z|float %}
	{% set combined_offset = user_offset + gcode_offset %}
	
	{% if force or user_offset != 0 or gcode_offset != 0 %}
	{% set title = "User-adjusted Z-offset of %.3f mm is active" % combined_offset %}
	{% set msg = "" %}
	{% set nl = "" %}
	{% if user_offset != 0 %}
	{% set msg = msg + "beacon true zero user Z-offset: %.3f mm (to clear, use Z_OFFSET_APPLY_PROBE CLEAR=1)" % user_offset %}
	{% set nl = "_N_" %}
	{% endif %}
	{% if gcode_offset != 0 %}
	{% set msg = msg + nl + "G-code Z-offset: %.3f mm" % gcode_offset %}
	{% endif %}
	CONSOLE_ECHO TITLE="{title}" TYPE="info" MSG="{msg}"
	{% endif %}

[gcode_macro _INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE]
gcode = 
	{% set variable = params.VARIABLE|string %}
	{% set svv = printer.save_variables.variables %}
	{% set nlu_msg = "no longer used, please remove" %}
	{% if svv[variable] is defined %}
	{% set v = svv[variable]|string|replace('"', '')|replace("'", "") %}
	{% if not nlu_msg in v %}
	SAVE_VARIABLE VARIABLE={variable} VALUE='"{nlu_msg} (was {v})"'
	{% endif %}
	CONSOLE_ECHO TITLE="Deprecated ratos-variables.cfg variable" TYPE="warning" MSG="The variable {variable} is no longer used, please remove it from your ratos-variables.cfg file."
	{% endif %}

[gcode_macro _NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK]
gcode = 
	
	
	
	
	
	
	
	{% set t = params.T|int %}
	{% set c = params.C|float %}
	{% set normal_low = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_low|default(0.05)|float %}
	{% set normal_high = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_high|default(0.10)|float %}
	
	{% if c < 0 %}
	
	{action_emergency_stop("Invalid nozzle_expansion_coefficient_t%s value in ratos-variables.cfg: %.3f. It must be non-negative." % (t, c))}
	{% endif %}
	{% if c >= normal_high %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite high. Please verify that this is correct."
	{% endif %}
	{% if c <= normal_low %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite low. Please verify that this is correct."
	{% endif %}

[gcode_macro INITIAL_FRONTEND_UPDATE]
gcode = 
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_error = printer["gcode_macro RatOS"].status_color_error|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_unknown}"'
	{% endif %}
	
	
	{% set t0_sensor = "undefined" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	{% set t0_sensor = "detected" %}
	{% else %}
	{% set t0_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t0_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	{% set t1_sensor = "undefined" %}
	{% if printer["dual_carriage"] is defined and printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	{% set t1_sensor = "detected" %}
	{% else %}
	{% set t1_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t1_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	{% if svv.t0_filament is defined and printer["gcode_macro T0"] is defined %}
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	{% if t0_sensor != "empty" %}
	{% set t0_filament_type = svv.t0_filament[0]|default('')|string %}
	{% set t0_filament_name = svv.t0_filament[1]|default('')|string %}
	{% set t0_filament_temp = svv.t0_filament[2]|default(0)|float %}
	{% if t0_filament_name != '' and t0_filament_type != '' and t0_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{t0_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{t0_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={t0_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}
	{% if svv.t1_filament is defined and printer["gcode_macro T1"] is defined %}
	{% if printer["gcode_macro T1"].filament_name is defined and printer["gcode_macro T1"].filament_type is defined and printer["gcode_macro T1"].filament_temp is defined %}
	{% if t1_sensor != "empty" %}
	{% set t1_filament_type = svv.t1_filament[0]|default('')|string %}
	{% set t1_filament_name = svv.t1_filament[1]|default('')|string %}
	{% set t1_filament_temp = svv.t1_filament[2]|default(0)|float %}
	{% if t1_filament_name != '' and t1_filament_type != '' and t1_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='"{t1_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='"{t1_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE={t1_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t1_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro CALCULATE_PRINTABLE_AREA]
variable_calculated = False
gcode = 
	{% if not calculated %}
	{% set bed_margin_x = printer["gcode_macro RatOS"].bed_margin_x %}
	{% set bed_margin_y = printer["gcode_macro RatOS"].bed_margin_y %}
	
	
	
	{% set tool = 0 if printer["gcode_macro T0"] is not defined or printer["gcode_macro T0"].active else 1 %}
	{% set max_x = printer.toolhead.axis_maximum.x if printer["dual_carriage"] is defined and tool == 0 else printer.toolhead.axis_maximum.x - bed_margin_x[1] %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	
	
	{% set max_x = printer.toolhead.axis_maximum.x %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="printer.toolhead.axis_maximum.x {printer.toolhead.axis_maximum.x}"
	
	{% set max_y = printer.toolhead.axis_maximum.y - bed_margin_y[1]%}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_x_max VALUE={max_x}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_y_max VALUE={max_y}
	SET_GCODE_VARIABLE MACRO=CALCULATE_PRINTABLE_AREA VARIABLE=calculated VALUE=True
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	RATOS_LOG PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	{% endif %}

[gcode_macro CACHE_TOOLHEAD_SETTINGS]
variable_cache = {"global": {"accel": 1000, "ratio": 0.5, "speed": 50, "scv": 5}}
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set dummy = cache.__setitem__(key, {"accel": printer.toolhead.max_accel, "ratio": printer.toolhead.minimum_cruise_ratio, "speed": printer.toolhead.max_velocity, "scv": printer.toolhead.square_corner_velocity}) %}
	SET_GCODE_VARIABLE MACRO=CACHE_TOOLHEAD_SETTINGS VARIABLE=cache VALUE="{cache | pprint | replace("\n", "") | replace("\"", "\\\"")}"
	DEBUG_ECHO PREFIX="CACHE_TOOLHEAD_SETTINGS" MSG="Toolhead settings cached for {key}. {printer.toolhead.max_accel} accel, {printer.toolhead.minimum_cruise_ratio} ratio, {printer.toolhead.max_velocity} velocity, {printer.toolhead.square_corner_velocity} scv."

[gcode_macro RESTORE_TOOLHEAD_SETTINGS]
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set values = printer["gcode_macro CACHE_TOOLHEAD_SETTINGS"].cache.__getitem__(key) %}
	{% if values is not defined or values == 'None' %}
	{ action_raise_error("RESTORE_TOOLHEAD_SETTINGS: Toolhead settings not cached for key '" ~ key ~ "'.") }
	{% endif %}
	SET_VELOCITY_LIMIT ACCEL={values.accel} MINIMUM_CRUISE_RATIO={values.ratio} VELOCITY={values.speed} SQUARE_CORNER_VELOCITY={values.scv}
	DEBUG_ECHO PREFIX="RESTORE_TOOLHEAD_SETTINGS" MSG="Toolhead settings restored. {values.accel} accel, {values.ratio} ratio, {values.speed} velocity, {values.scv} scv."

[gcode_macro SET_MACRO_TRAVEL_SETTINGS]
gcode = 
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float %}
	{% set accel = printer["gcode_macro RatOS"].macro_travel_accel %}
	SET_VELOCITY_LIMIT ACCEL={accel} MINIMUM_CRUISE_RATIO=0.5 VELOCITY={speed} SQUARE_CORNER_VELOCITY={5}
	DEBUG_ECHO PREFIX="SET_MACRO_TRAVEL_SETTINGS" MSG="Macro travel settings set. {accel} accel, {speed} velocity"

[gcode_macro SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% if printer["dual_carriage"] is not defined %}
	
	SET_KINEMATIC_POSITION X={printable_x_max / 2} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	{% else %}
	
	IDEX_SET_CENTER_KINEMATIC_POSITION
	{% endif %}

[gcode_macro IDEX_SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x - (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x + (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY

[gcode_macro VERIFY_HYBRID_INVERTED]
gcode = 
	
	{% set inverted = False %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy is defined and printer.fastconfig.settings.ratos_hybrid_corexy.inverted is defined %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy.inverted|lower == 'true' %}
	{% set inverted = True %}
	{% endif %}
	{% endif %}
	{% if inverted == False %}
	{ action_emergency_stop("ratos_hybrid_corexy NOT INVERTED! Inverted hybrid core-xy bugfix not detected.") }
	{% endif %}

[gcode_macro RATOS_ECHO]
gcode = 
	{% set prefix = "RatOS" %}
	{% set debug = params.DEBUG|default(0)|int %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " | " ~ params.PREFIX %}
	{% endif %}
	{% set prefix = prefix ~ ":" %}
	{% set msg = "" %}
	{% if params.MSG is defined %}
	{% set msg = params.MSG %}
	{% else %}
	{% set msg = "No msg parameter provided (this is a bug or unintended use)." %}
	{% endif %}
	{% if not debug %}
	
	M117 {prefix} {msg}
	{% endif %}
	RATOS_LOG PREFIX="{prefix}" MSG="{msg}"
	{% if not debug %}
	RESPOND PREFIX="{prefix}" MSG="{msg}"
	{% else %}
	CONSOLE_ECHO TITLE="{prefix}" TYPE="debug" MSG="{msg}"
	{% endif %}

[gcode_macro ENABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=True
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=prefix_filter VALUE="'{params.FILTER|default('')|lower}'"
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging enabled."

[gcode_macro DISABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=False
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging disabled."

[gcode_macro DEBUG_ECHO]
variable_enabled = False
variable_prefix_filter = ''
gcode = 
	{% set prefix = "DEBUG" %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " - " ~ params.PREFIX %}
	{% endif %}
	{% if enabled and (prefix_filter|lower == '' or prefix_filter|lower in params.PREFIX|lower) %}
	RATOS_ECHO PREFIX="{prefix}" MSG="{params.MSG}" DEBUG=1
	{% endif %}

[gcode_macro START_FEATURE]
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="Start {params.FEATURE} feature gcode"
	{% set scv = printer.toolhead.square_corner_velocity|int|default(5) %}
	{% set accel = printer.toolhead.max_accel|int|default(10000) %}
	{% set ratio = printer.toolhead.minimum_cruise_ratio|float|default(0.5) %}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="scv" VALUE={scv}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="accel" VALUE={accel}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="ratio" VALUE={ratio}
	_USER_START_FEATURE FEATURE="{params.FEATURE}"

[gcode_macro END_FEATURE]
variable_scv = 5
variable_accel = 10000
variable_ratio = 0.5
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="End {params.FEATURE} feature gcode"
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={scv} ACCEL={accel} MINIMUM_CRUISE_RATIO={ratio}
	_USER_END_FEATURE FEATURE="{params.FEATURE}" SCV={scv} ACCEL={accel} RATIO={ratio}

[gcode_macro _ON_LAYER_CHANGE]
variable_layer_number = 0
description = INTERNAL USE ONLY. Call it from the slicers after layer change custom gcode
gcode = 
	
	{% set layer = params.LAYER|int %}
	
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE={layer}
	SET_PRINT_STATS_INFO CURRENT_LAYER={layer}

[gcode_macro _LEARN_MORE_CALIBRATION]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/calibration" %}
	{% set link_text = "RatOS Calibration Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_CHAMBER_FILTER]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter Control" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_FILAMENT]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/filaments" %}
	{% set link_text = "RatOS Filament Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _CONSOLE_SAVE_CONFIG]
gcode = 
	M118 Click <a class="command text--blue">SAVE_CONFIG</a> to save the settings to your printer.cfg.

[gcode_macro _LOAD_RATOS_SKEW_PROFILE]
gcode = 
	{% set ratos_skew_profile = printer["gcode_macro RatOS"].skew_profile|default("") %}
	{% if ratos_skew_profile != "" %}
	{% if printer.fastconfig.config["skew_correction %s" % ratos_skew_profile] is defined %}
	SKEW_PROFILE LOAD={ratos_skew_profile}
	GET_CURRENT_SKEW
	{% else %}
	{% set line_1 = '"Could not find skew profile %s!_N_Clearing skew correction."' % ratos_skew_profile %}
	CONSOLE_ECHO TITLE="Missing skew profile!" TYPE="warning" MSG={line_1}
	SET_SKEW CLEAR=1
	{% endif %}
	{% endif %}

[gcode_macro M601]
gcode = 
	PAUSE

[gcode_macro _STOP_AND_RAISE_ERROR]
gcode = 
	M84
	_RAISE_ERROR MSG="{params.MSG}"

[gcode_macro _RESET_GCODE_VARIABLES]
description = Reset specified [gcode_macro ...] variables to their original values from configuration when Klipper started.
	- MACRO: Name of the GCODE macro containing the variables to reset.
	- VARIABLES: Comma-separated list of variable names to reset (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- QUIET: (optional) If true, suppresses console echo messages for each reset variable. Default is false.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set quiet = params.QUIET|default("false")|lower in ("true", "1", "yes") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	{% set settings = printer.fastconfig.settings[obj_name|lower] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro %s]" % macro) }
	{% endif %}
	
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if settings["variable_%s" % var] is not defined %}
	{ action_raise_error("Variable '%s' is not defined in settings for [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	
	{% for var in vars %}
	{% set var_value = obj[var] %}
	{% if var_value is defined %}
	{% set v = settings["variable_%s" % var] %}
	{% if v != var_value|string %}
	{% if var_value is string %}
	{% set v = '"\'' ~ v|replace('"', '\\"')|replace("'", "\\'") ~ '\'"' %}
	{% endif %}
	SET_GCODE_VARIABLE MACRO={macro} VARIABLE={var} VALUE={v}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Reset {macro} variable {var} to original value: {v} (was {obj[var]})"
	{% endif %}
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro _SHOW_GCODE_VARIABLES]
description = Show current values of specified [gcode_macro ...] variables.
	- MACRO: Name of the GCODE macro containing the variables to show.
	- VARIABLES: Comma-separated list of variable names to show (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- PAD: (optional) If defined, provide a single character to use for padding variable names to align values in a tabular format in the console output. Default is no padding.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set pad = params.PAD|default("") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	
	{% set ns = namespace() %}
	{% set ns.max_len = 0 %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% set ns.max_len = (ns.max_len, var|length)|max %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if pad %}
	{% set padding = pad * (ns.max_len - var|length) %}
	CONSOLE_ECHO MSG="{var}{padding} {obj[var]}"
	{% else %}
	CONSOLE_ECHO MSG="{var}: {obj[var]}"
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro PAUSE]
description = Pauses the print
rename_existing = PAUSE_BASE
variable_extrude = 1.5
variable_retract = 1.5
variable_fan_speed = 0
variable_idex_mode = ""
variable_idex_toolhead = 0
variable_idex_toolhead_x = 0.0
variable_idex_toolhead_y = 0.0
variable_idex_toolhead_z = 0.0
gcode = 
	RATOS_ECHO MSG="Pausing print..."
	
	
	{% set runout_detected = true if params.RUNOUT|default(false)|lower == 'true' else false %}
	
	
	_LED_PAUSE
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	SAVE_GCODE_STATE NAME=PAUSE_state
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_mode VALUE='"{idex_mode}"'
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={idex_toolhead}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_x VALUE={printer.gcode_move.gcode_position.x|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_y VALUE={printer.gcode_move.gcode_position.y|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_z VALUE={printer.gcode_move.gcode_position.z|float}
	DEBUG_ECHO PREFIX="PAUSE" MSG="idex_mode: {idex_mode}, idex_toolhead: {idex_toolhead}, idex_toolhead_x: {idex_toolhead_x}, idex_toolhead_y: {idex_toolhead_y}, idex_toolhead_z: {idex_toolhead_z}"
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="pause"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if current_z < (max_z - 20.0) %}
	{% set z_safe = 20.0 %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	PAUSE_BASE
	
	
	{% if printer["dual_carriage"] is not defined %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan"].speed|float}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	{% if idex_toolhead == 0 %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t1"].speed|float}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106 S0
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set R = printer["gcode_macro PAUSE"].retract|float %}
	{% if can_extrude %}
	G91
	G1 E-{R} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	{% set pause_print_park_x = printer["gcode_macro RatOS"].pause_print_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].pause_print_park_in %}
	{% if runout_detected %}
	{% set pause_print_park_x = printer["gcode_macro RatOS"].runout_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].runout_park_in %}
	{% endif %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	DEBUG_ECHO PREFIX="PAUSE" MSG="z_speed: {z_speed}, pause_print_park_x: {pause_print_park_x}, pause_print_park_in: {pause_print_park_in}, default_toolhead: {default_toolhead}"
	{% if "xyz" in printer.toolhead.homed_axes %}
	G91
	G1 Z{z_safe} F{z_speed}
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% else %}
	
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	_IDEX_SINGLE X={parking_position}
	{% else %}
	PARK_TOOLHEAD
	{% endif %}
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="pause"
	
	RATOS_ECHO MSG="Print paused"

[gcode_macro RESUME]
description = Resumes the print if the printer is paused.
rename_existing = RESUME_BASE
gcode = 
	
	
	RATOS_ECHO MSG="Resuming print..."
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	
	{% set target_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set target_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if target_idex_mode != '' %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set fan_speed = printer["gcode_macro PAUSE"].fan_speed|float %}
	{% if printer["dual_carriage"] is not defined %}
	M106 S{(fan_speed * 255)}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% else %}
	{% if params.TOOLHEAD is defined %}
	
	{% if params.TOOLHEAD == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% else %}
	{% if printer["gcode_macro PAUSE"].idex_toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	{% if params.TOOLHEAD is defined %}
	_SELECT_TOOL T={params.TOOLHEAD} X=-1 Y=-1 TOOLSHIFT=false
	{% else %}
	_SELECT_TOOL T={printer["gcode_macro PAUSE"].idex_toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	{% endif %}
	
	{% set x = printer["gcode_macro PAUSE"].idex_toolhead_x|float %}
	{% set y = printer["gcode_macro PAUSE"].idex_toolhead_y|float %}
	{% set z = printer["gcode_macro PAUSE"].idex_toolhead_z|float %}
	G1 X{x} Y{y} Z{z} F{speed}
	{% if params.TOOLHEAD is defined %}
	
	SAVE_GCODE_STATE NAME=PAUSE_STATE
	{% endif %}
	{% endif %}
	
	
	{% if params.TOOLHEAD is not defined %}
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% if can_extrude %}
	G91
	G1 E{E} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1 MOVE_SPEED={speed}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	RESUME_BASE
	
	
	_LED_PRINTING
	
	RATOS_ECHO MSG="Print resumed"

[gcode_macro CANCEL_PRINT]
description = Cancels the print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	RATOS_ECHO MSG="Cancelling print..."
	END_PRINT
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	
	CANCEL_PRINT_BASE
	RATOS_ECHO MSG="Print cancelled"

[gcode_macro START_PRINT]
description = Start print procedure, use this in your Slicer.
variable_post_processor_version = 2
variable_is_printing_gcode = False
variable_both_toolheads = True
variable_object_xoffset = 0
variable_first_x = -1
variable_first_y = -1
variable_total_toolshifts = 0
variable_initial_tool = 0
variable_extruder_first_layer_temp = ""
variable_extruder_other_layer_temp = ""
gcode = 
	
	{% if params.EXTRUDER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_TEMP parameter not found.")}
	{% endif %}
	{% if params.EXTRUDER_OTHER_LAYER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_OTHER_LAYER_TEMP parameter not found.")}
	{% endif %}
	{% if params.BED_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. BED_TEMP parameter not found.")}
	{% endif %}
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' and printer["gcode_macro RatOS"].danger_force_allow_auto_center_subject|default(false)|lower != 'true'%}
	
	
	
	
	
	{ action_raise_error("The experimental auto_center_subject feature is not supported in this version of RatOS. Please disable it in the RatOS macro settings.") }
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes and printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% if printer["gcode_macro _VAOC"].is_started|default(true)|lower == 'true' %}
	_VAOC_END
	{% endif %}
	{% endif %}
	
	
	_LED_START_PRINTING
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_USER_START_PRINT { rawparams }
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_probe_stowable = printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% endif %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	{% set X0 = params.X0|default(-1)|float %}
	{% set X1 = params.X1|default(-1)|float %}
	{% set Y0 = params.Y0|default(-1)|float %}
	{% set Y1 = params.Y1|default(-1)|float %}
	{% if first_x == -1 or first_y == -1 %}
	{% set first_x = params.FIRST_X|default(-1)|float %}
	{% set first_y = params.FIRST_Y|default(-1)|float %}
	{% endif %}
	{% set total_toolshifts = params.TOTAL_TOOLSHIFTS|default(0)|int %}
	{% set initial_tool = params.INITIAL_TOOL|default(default_toolhead)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	
	
	
	
	
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(printer.heater_bed.target, true)|float %}
	
	
	{% set total_layer_count = params.TOTAL_LAYER_COUNT|default(0)|int %}
	{% set extruder_first_layer_temp = (params.EXTRUDER_TEMP|default("")).split(",") %}
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL BEACON_CONTACT_START_PRINT_TRUE_ZERO={beacon_contact_start_print_true_zero} BEACON_CONTACT_CALIBRATE_MODEL_ON_TRUE_ZERO={beacon_contact_calibrate_model_on_true_zero}
	{% endif %}
	
	_START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH BED_TEMP={bed_temp}
	
	
	RATOS_ECHO MSG="First print coordinates X:{first_x} Y:{first_y}"
	
	
	{% if params.TOTAL_LAYER_COUNT is not defined %}
	{% set link_url = "https://os.ratrig.com/docs/slicers" %}
	{% set link_text = "RatOS Slicer Configuration" %}
	{% set line_1 = '"Your slicer gcode settings are not up to date._N_Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="Incomplete Slicer Configuration detected" TYPE="warning" MSG={line_1}
	{% endif %}
	
	
	SET_PRINT_STATS_INFO CURRENT_LAYER=1
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE=1
	{% if total_layer_count > 0 %}
	SET_PRINT_STATS_INFO TOTAL_LAYER={total_layer_count}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads %}
	{% set initial_tool = 0 if initial_tool == 1 else 1 %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	{% endif %}
	
	
	{% set both_toolheads = true %}
	{% if total_toolshifts == 0 %}
	{% set both_toolheads = false %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	{% endif %}
	{% if both_toolheads and (idex_mode == "copy" or idex_mode == "mirror") %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Gcode tool changes found. Copy and mirror mode do not support toolchanges.")}
	{% endif %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set both_toolheads = true %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=initial_tool VALUE={initial_tool}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_x VALUE={first_x}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_y VALUE={first_y}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=total_toolshifts VALUE={total_toolshifts}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=both_toolheads VALUE={both_toolheads}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_first_layer_temp VALUE="'{params.EXTRUDER_TEMP}'"
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_other_layer_temp VALUE="'{params.EXTRUDER_OTHER_LAYER_TEMP}'"
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE=0
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set svv = printer.save_variables.variables %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set stepper_x_position_min = printer.fastconfig.settings.stepper_x.position_min|float %}
	{% set stepper_x_position_endstop = printer.fastconfig.settings.stepper_x.position_endstop|float %}
	{% set dual_carriage_position_max = printer.fastconfig.settings.dual_carriage.position_max|float %}
	{% set dual_carriage_position_endstop = printer.fastconfig.settings.dual_carriage.position_endstop|float %}
	{% set x_parking_space = parking_position_t0 - (stepper_x_position_endstop , stepper_x_position_min)|max %}
	{% set dc_parking_space = (dual_carriage_position_endstop , dual_carriage_position_max)|min - parking_position_t1 %}
	{% if svv.idex_xoffset|abs >= (x_parking_space - 0.5) or svv.idex_xoffset|abs >= (dc_parking_space - 0.5) %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Toolhead x-offset is too high for the available parking space. Calibrate your X and DC endstop positions and make sure you stay below 1mm." % (copy_mode_max_width)) }
	{% endif %}
	{% endif %}
	
	
	{% if (idex_mode == "copy" or idex_mode == "mirror") and printer.fastconfig.settings.ratos.enable_gcode_transform %}
	
	{% if params.MIN_X is not defined or params.MAX_X is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Something went wrong! Missing important post processor start print parameter!") }
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE=0
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	
	{% set boundary_box_min_x = params.MIN_X|default(0)|float %}
	{% set boundary_box_max_x = params.MAX_X|default(printable_x_max)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if default_toolhead == 0 %}
	
	{% set boundary_box_max_x = boundary_box_max_x + svv.idex_xoffset %}
	{% else %}
	
	{% set boundary_box_min_x = boundary_box_min_x - svv.idex_xoffset %}
	{% endif %}
	
	{% set center_x = printable_x_max / 2.0 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set object_width = boundary_box_max_x - boundary_box_min_x %}
	{% set copy_mode_max_width = center_x %}
	{% set mirror_mode_max_width = center_x - safe_distance / 2.0 %}
	
	DEBUG_ECHO PREFIX="START_PRINT" MSG="OBJECT_WIDTH: {object_width} BOUNDARY_BOX_MIN_X: {boundary_box_min_x} BOUNDARY_BOX_MAX_X: {boundary_box_max_x} CENTER_X: {center_x} SAFE_DISTANCE: {safe_distance}"
	
	
	{% if idex_mode == "copy" and object_width > copy_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for copy mode! Max supported width is %s mm" % (copy_mode_max_width)) }
	{% endif %}
	{% if idex_mode == "mirror" and object_width > mirror_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for mirror mode! Max supported width is %s mm" % (mirror_mode_max_width)) }
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = (printable_x_max - boundary_box_max_x - boundary_box_min_x) / 2 %}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE={object_xoffset}
	{% endif %}
	
	{% endif %}
	
	
	{% set has_initial_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_toolhead_filament_sensor %}
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% set has_initial_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_bowden_filament_sensor %}
	
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% if printer["dual_carriage"] is defined and both_toolheads %}
	
	{% set has_secondary_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set has_secondary_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_CHAMBER_FILTER_ON AT="before_print_start"
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true' %}
	{% if both_toolheads %}
	RATOS_ECHO MSG="Spool join is not possible if both toolheads are in use!"
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	{% endif %}
	
	
	CLEAR_PAUSE
	{% if printer["gcode_macro RatOS"].force_absolute_position|lower == 'true' %}
	G90
	{% endif %}
	SAVE_GCODE_STATE NAME=start_print_state
	
	
	G21
	
	G90
	
	M82
	_USER_START_PRINT_BEFORE_HOMING { rawparams }
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_BEGIN_BATCH
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_Z_HOP
	
	
	{% if idex_mode != '' and not (printer.fastconfig.settings.beacon is defined and (beacon_contact_start_print_true_zero or beacon_adaptive_heat_soak)) %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	{% if chamber_temp > 0 %}
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED={printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float}
	{% endif %}
	{% endif %}
	_CHAMBER_HEATER_ON START_CHAMBER_TEMP={start_chamber_temp} CHAMBER_TEMP={chamber_temp}
	_USER_START_PRINT_HEAT_CHAMBER { rawparams } CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_START_PRINT_BEFORE_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	RATOS_ECHO MSG="Heating bed..."
	
	M190 S{bed_temp}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_adaptive_heat_soak %}
	_MOVE_TO_SAFE_Z_HOME
	
	G1 Z2.5 F{z_speed}
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK LAYER_QUALITY={beacon_adaptive_heat_soak_layer_quality} MAXIMUM_FIRST_LAYER_DURATION={beacon_adaptive_heat_soak_maximum_first_layer_duration} MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={beacon_adaptive_heat_soak_max_wait}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_BED { rawparams }
	
	
	_START_PRINT_AFTER_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	_USER_START_PRINT_BED_MESH { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_BED_MESH X0={X0} X1={X1} Y0={Y0} Y1={Y1} T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_END_BATCH
	{% endif %}
	
	
	{% if idex_mode == '' %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[initial_tool]|float}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[0]|float}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={extruder_first_layer_temp[1]|float}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_PARK { rawparams }
	
	
	_START_PRINT_PARK
	
	
	RATOS_ECHO MSG="Heating Extruder..."
	{% if idex_mode == '' %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[initial_tool]|float}  MAXIMUM={extruder_first_layer_temp[initial_tool]|float + 5}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[0]|float}  MAXIMUM={extruder_first_layer_temp[0]|float + 5}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder1" MINIMUM={extruder_first_layer_temp[1]|float}  MAXIMUM={extruder_first_layer_temp[1]|float + 5}
	{% endif %}
	{% endif %}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	{% if idex_mode == '' %}
	_LED_PRINTING
	{% else %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	_LED_PRINTING
	{% else %}
	{% if both_toolheads %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	{% if toolchange_standby_temp > -1 %}
	_LED_TOOLHEAD_STANDBY TOOLHEAD={0 if initial_tool == 1 else 1}
	{% else %}
	_LED_PRINTING TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% else %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_EXTRUDER { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_AFTER_HEATING_EXTRUDER X0={X0} X1={X1} Y0={Y0} Y1={Y1} INITIAL_TOOLHEAD={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if idex_mode != '' %}
	{% if not both_toolheads %}
	{% if initial_tool != default_toolhead %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if idex_mode != '' %}
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=standby VALUE=False
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=standby VALUE=False
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if initial_tool == 1 else 'extruder1'} TARGET={toolchange_standby_temp}
	SET_GCODE_VARIABLE MACRO=T{0 if initial_tool == 1 else 1} VARIABLE=standby VALUE=True
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=start_print_state
	
	{% if printer["dual_carriage"] is defined %}
	_SET_IDEX_MODE_OFFSET
	{% endif %}
	
	
	{% if idex_mode != '' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% if idex_mode == "copy" and idex_mode != act_idex_mode %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == "mirror" and idex_mode != act_idex_mode %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={object_xoffset} MOVE=0
	{% endif %}
	{% else %}
	_SELECT_TOOL T={initial_tool} TOOLSHIFT=false
	_SET_TOOLHEAD_OFFSET
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	_SET_EXTRUSION_MODE
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={printer["print_stats"].print_duration}
	{% endif %}
	
	
	_USER_END_START_PRINT { rawparams }
	
	G92 E0
	
	
	_CHAMBER_FILTER_ON AT="after_print_start"
	
	_ALERT_NON_ZERO_Z_OFFSET
	
	RATOS_ECHO MSG="Printing..."

[gcode_macro _START_PRINT_BEFORE_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set is_stowable_probe = true if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' else false %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Pre-heating extruder..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={min_temp}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET={min_temp}
	{% endif %}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	{% endif %}
	{% endif %}
	
	
	{% if not is_stowable_probe %}
	{% if printer["dual_carriage"] is defined and act_t != default_toolhead %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	{% endif %}
	RATOS_ECHO MSG="Heat soaking z probe..."
	_MOVE_TO_SAFE_Z_HOME
	
	G0 Z2 F{z_speed}
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Waiting for extruder to be preheated..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	{% if default_toolhead == 0 %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_Z_HOP
	{% endif %}
	
	
	{% if auto_z_offset_calibration %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	PARK_TOOLHEAD
	_CLEANING_MOVE TOOLHEAD={default_toolhead} AUTOMATED=True
	_SELECT_TOOL T={0 if default_toolhead == 1 else 1} X={parking_position_t0 if default_toolhead == 1 else parking_position_t1} Y=0 TOOLSHIFT=false
	_CLEANING_MOVE TOOLHEAD={0 if default_toolhead == 1 else 1} AUTOMATED=True
	_VAOC_CALIBRATE_Z_OFFSET AUTO_Z_OFFSET=True
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=false
	{% endif %}
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	{% if needs_rehoming %}
	G28 Z
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	_START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE
	{% endif %}
	{% endif %}
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	PROBE PROBE_METHOD=contact SAMPLES=1

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	{% set fuzzy_radius = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_radius|default(0)|float if beacon_contact_start_print_true_zero_fuzzy_position else 0 %}
	
	{% set contact_true_zero_temp_has_been_set = False %}
	
	
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	
	
	
	{% if printer.beacon.last_probe_result|lower == "ok" %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	RATOS_ECHO MSG="Auto calibration nozzle wipe with probe result {last_z_offset}..."
	G0 Z{(0.2 + last_z_offset)} F{z_speed}
	G0 X70 F300
	{% else %}
	RATOS_ECHO MSG="Skipping auto calibration nozzle wipe because probing failed!"
	{% endif %}
	{% elif beacon_contact_wipe_before_true_zero_method == "probe_clean" %}
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	
	{% set contact_true_zero_temp_has_been_set = True %}
	
	
	
	
	
	
	
	
	BEACON_PROBE_CLEAN X=50 Y=10
	{% else %}
	CONSOLE_ECHO TYPE="error" TITLE="Unknown wipe method" MSG="Unknown wipe method '{beacon_contact_wipe_before_true_zero_method}' configured, skipping wipe before beacon true zero."
	{% endif %}
	{% endif %}
	
	
	G0 Z5 F{z_speed}
	_MOVE_TO_SAFE_Z_HOME FUZZY_RADIUS={fuzzy_radius}
	
	
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION
	
	{% if not contact_true_zero_temp_has_been_set %}
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon contact auto calibration..."
	
	{% if beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	
	G0 Z5 F{z_speed}

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION]
gcode = 
	{% set pos = printer.ratos.last_move_to_safe_z_home_position %}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE={pos[0]}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE={pos[1]}

[gcode_macro _START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set first_x = printer["gcode_macro START_PRINT"].first_x|default(-1)|float %}
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2.0 %}
	{% set center_y = printable_y_max / 2.0 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% if printer["dual_carriage"] is defined %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% endif %}
	
	
	{% set X0 = params.X0|default(-1)|int %}
	{% set X1 = params.X1|default(-1)|int %}
	{% set Y0 = params.Y0|default(-1)|int %}
	{% set Y1 = params.Y1|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	
	{% if idex_mode == '' %}
	
	_PRIME
	{% else %}
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	RATOS_ECHO PREFIX="IDEX" MSG="using combined prime offset for IDEX {idex_mode} mode"
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	{% if both_toolheads %}
	{% if initial_toolhead == 0 %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T{initial_toolhead}"
	_SELECT_TOOL T={initial_toolhead} TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	SET_MACRO_TRAVEL_SETTINGS
	
	{% if (X0 > -1 and Y1 > -1) or (first_x > 0 and first_y > 0) %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	{% endif %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	{% set first_z = 1 %}
	{% else %}
	{% set first_z = 3 %}
	{% endif %}
	
	
	{% if idex_mode == "mirror" %}
	{% if first_y >= 0 %}
	G0 Y{first_y} F{speed}
	{% else %}
	G0 Y{Y1} F{speed}
	{% endif %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={initial_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={initial_toolhead} E={printer["gcode_macro RatOS"].toolchange_first_purge|default(50)|float}
	_CLEANING_MOVE TOOLHEAD={initial_toolhead} AUTOMATED=True
	{% endif %}
	{% if first_x >= 0 and first_y >= 0 %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% else %}
	{% set first_x = X0 %}
	{% set first_y = Y0 %}
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'min' %}
	{% set first_x = X0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'max' %}
	{% set first_x = X1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|float <= center_x %}
	{% set first_x = X0 %}
	{% else %}
	{% set first_x = X1 %}
	{% endif %}
	{% endif %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'min' %}
	{% set first_y = Y0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'max' %}
	{% set first_y = Y1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|float <= center_y %}
	{% set first_y = Y0 %}
	{% else %}
	{% set first_y = Y1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	
	
	_LOAD_RATOS_SKEW_PROFILE

[gcode_macro _PRIME]
gcode = 
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	PRIME_BLOB INITIAL_TOOLHEAD={params.INITIAL_TOOLHEAD} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={params.IDEX_MODE} Y1={params.Y1}
	{% else %}
	
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif params.IDEX_MODE == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro END_PRINT]
description = End print procedure, use this in your Slicer.
gcode = 
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SAVE_GCODE_STATE NAME=end_print_state
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = printer["gcode_macro START_PRINT"].object_xoffset|default(0)|float %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(0-object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={(0-object_xoffset)}
	{% endif %}
	{% endif %}
	
	
	_USER_END_PRINT_BEFORE_HEATERS_OFF { rawparams }
	_END_PRINT_BEFORE_HEATERS_OFF
	TURN_OFF_HEATERS
	_USER_END_PRINT_AFTER_HEATERS_OFF { rawparams }
	_END_PRINT_AFTER_HEATERS_OFF
	_USER_END_PRINT_PARK { rawparams }
	_END_PRINT_PARK
	
	
	{% if printer["gcode_macro RatOS"].skew_profile is defined %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined and printer["gcode_macro RatOS"].end_print_motors_off|lower != 'false' %}
	
	M84
	{% endif %}
	
	
	M107
	
	
	BED_MESH_CLEAR
	RATOS_ECHO MSG="Done :)"
	
	
	RESTORE_GCODE_STATE NAME=end_print_state
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	M84
	{% endif %}
	
	
	RESET_NAMED_OFFSET EVENT="end_print"
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_CHAMBER_FILTER_ON AT="print_end"
	_CHAMBER_FILTER_OFF
	
	
	_CHAMBER_HEATER_OFF
	
	_USER_END_PRINT_FINISHED { rawparams }

[gcode_macro _END_PRINT_BEFORE_HEATERS_OFF]
gcode = 
	RATOS_ECHO MSG="Cleaning up..."

[gcode_macro _END_PRINT_AFTER_HEATERS_OFF]
gcode = 
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% set z_hop = printer["gcode_macro RatOS"].end_print_park_z_hop|float %}
	{% set r = printer["gcode_macro RatOS"].end_print_retract_filament|default(4)|float %}
	{% if current_z < (max_z - z_hop) %}
	{% set z_safe = z_hop %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G91
	
	{% if can_extrude %}
	G1 E-2 F3600
	{% endif %}
	
	G0 Z{z_safe} F3600
	
	{% if can_extrude %}
	G1 E-{(r-2)} F3600
	{% endif %}
	
	G90

[gcode_macro _SET_EXTRUSION_MODE]
gcode = 
	
	{% if printer["gcode_macro RatOS"].relative_extrusion|lower == 'true' %}
	M83
	{% else %}
	M82
	{% endif %}

[gcode_macro GENERATE_SHAPER_GRAPHS]
description = Genarates input shaper resonances graphs for analysis. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	{% set hz_per_sec = params.HZ_PER_SEC|default(1)|float %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set copy_mode_offset = printable_x_max / 4.0 %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	_IDEX_SINGLE
	{% endif %}
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	
	
	{% if idex_mode != 'copy' and idex_mode != 'mirror' %}
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	{% endif %}
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Shaper graph"

[gcode_shell_command generate_shaper_graph_x]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-x.sh
timeout = 60.
verbose = True

[gcode_shell_command generate_shaper_graph_y]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-y.sh
timeout = 60.
verbose = True

[gcode_macro MEASURE_COREXY_BELT_TENSION]
description = Generates resonance graph used to ensure belts are equally tensioned. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	_IDEX_SINGLE
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if measure_t1 == false or measure_t0 == false %}
	{action_raise_error("Axis specified. Not supported for belt tension on Y.")}
	{% else %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	G4 P5000
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	PARK_TOOLHEAD
	{% endif %}
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	G1 X{parking_position_t1} F{speed}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	
	
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Belt Tension Graph"

[gcode_shell_command generate_belt_tension_graph]
command = /home/pi/printer_data/config/RatOS/scripts/generate-belt-tension-graph.sh
timeout = 90.
verbose = True

[idle_timeout]
gcode = 
	{% if printer.webhooks.state|lower == 'ready' %}
	{% if printer.pause_resume.is_paused|lower == 'false' %}
	_USER_BEFORE_IDLE_TIMEOUT
	RATOS_ECHO PREFIX="IDLE" MSG="2 hours since last activity. Powering off heaters and motors.."
	TURN_OFF_HEATERS
	M84
	_USER_AFTER_IDLE_TIMEOUT
	{% endif %}
	{% endif %}
timeout = 7200

[temperature_sensor raspberry_pi]
sensor_type = temperature_host

[skew_correction]

[named_offsets]

[input_shaper]

[virtual_sdcard]
path = ~/printer_data/gcodes

[display_status]

[pause_resume]

[force_move]
enable_force_move = True

[respond]

[resonance_generator]

[ratos]
allow_unknown_gcode_generator = True
enable_gcode_transform = True

[exclude_object]

[bed_mesh]
split_delta_z = 0.001
horizontal_move_z = 2
mesh_min = 20,20
mesh_max = 480,480
probe_count = 40,40
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = .2
speed = 600
log_points = False

[fastconfig]

[heater_bed]
heater_pin = heater_bed_heating_pin
sensor_pin = heater_bed_sensor_pin
sensor_type = Generic 3950
min_temp = 0
max_temp = 140
pwm_cycle_time = 0.103
control = pid
pid_kp = 61.987
pid_ki = 1.781
pid_kd = 539.289

[printer]
kinematics = ratos_hybrid_corexy
max_velocity = 800
max_accel = 10000
minimum_cruise_ratio = 0.5
max_z_velocity = 50
max_z_accel = 600
square_corner_velocity = 5

[ratos_hybrid_corexy]
inverted = true

[dual_carriage]
axis = x
safe_distance = 55
position_max = 559.6
position_endstop = 559.6
position_min = 0
step_pin = PF9
dir_pin = dual_carriage_dir_pin
enable_pin = !PG2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t1:PA2

[gcode_macro _SET_IDEX_MODE_OFFSET]
description = "Internal use only. Sets the 'idex_mode' named offset that the active idex mode requires."
gcode = 
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_SET_IDEX_MODE_OFFSET" MSG="idex_mode: {idex_mode}, center_x: {center_x}"
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	SET_NAMED_OFFSET NAME=idex_mode X={(-center_x / 2)}
	{% else %}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% else %}
	{action_raise_error("_SET_IDEX_MODE_OFFSET: Printer not homed")}
	{% endif %}

[gcode_macro IDEX_SINGLE]
gcode = 
	_IDEX_REMAP_TOOLHEADS ENABLE=False
	_IDEX_SINGLE

[gcode_macro _IDEX_SINGLE]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_single"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set init = params.INIT|default(0)|int %}
	{% set new_x = params.X|default(-1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_default_t = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="init: {init}, new_x: {new_x}, idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, act_t: {act_t}"
	
	{% if idex_mode == "copy" or idex_mode == "mirror" or init == 1 %}
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="reset idex_mode offset"
	G1 X{center_x} F{(speed)}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="activate default carriage"
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolheads"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	G90
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position."
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1}
	G1 X{parking_position_default_t} F{speed}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move default toolhead to its new position."
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% if new_x == -1 %}
	{% set new_x = center_x %}
	{% endif %}
	G1 X{new_x} F{speed}
	
	M400
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="X Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set extruder motion queue."
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if default_toolhead==0 else default_toolhead}
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolhead offset."
	_SET_TOOLHEAD_OFFSET
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set input shaper."
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[default_toolhead]|float)} SHAPER_FREQ_Y={(shaper_y_freq[default_toolhead]|float)} SHAPER_TYPE_X={(shaper_x_type[default_toolhead]|lower)} SHAPER_TYPE_Y={(shaper_y_type[default_toolhead]|lower)}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="update Frontend."
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if default_toolhead==0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if default_toolhead==1 else False}
	{% else %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_single"

[gcode_macro IDEX_COPY]
gcode = 
	_IDEX_COPY

[gcode_macro _IDEX_COPY]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_copy"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set y = params.Y|default(-1)|int %}
	{% set dance = params.DANCE|default(1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_COPY" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}, y: {y}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "copy" %}
	{% if idex_mode == "mirror" %}
	{% if y>=0 %}
	G1 X{center_x} Y{y} F{(speed)}
	{% else %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	
	
	{% if idex_mode != "mirror" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance == 1 %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[2]|float)} SHAPER_FREQ_Y={(shaper_y_freq[2]|float)} SHAPER_TYPE_X={(shaper_x_type[2]|lower)} SHAPER_TYPE_Y={(shaper_y_type[2]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_copy"

[gcode_macro IDEX_MIRROR]
gcode = 
	_IDEX_MIRROR

[gcode_macro _IDEX_MIRROR]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_mirror"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set dance = params.DANCE|default(1)|int %}
	{% set priming = params.PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_MIRROR" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "mirror" %}
	
	{% if idex_mode == "copy" %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS MIRROR_PRIMING={params.PRIMING}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=MIRROR
	
	
	{% if idex_mode != "copy" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance and not priming %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[3]|float)} SHAPER_FREQ_Y={(shaper_y_freq[3]|float)} SHAPER_TYPE_X={(shaper_x_type[3]|lower)} SHAPER_TYPE_Y={(shaper_y_type[3]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_mirror"

[gcode_macro _IDEX_SET_TOOLHEADS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set mirror_priming = params.MIRROR_PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position_inactive_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_IDEX_SET_TOOLHEADS" MSG="idex_mode: {idex_mode}, act_t: {act_t}, center_x: {center_x}, mirror_priming: {mirror_priming}"
	
	
	{% if act_t != default_toolhead %}
	_SET_TOOLHEAD_OFFSET FORCE_TOOLHEAD={default_toolhead} MOVE=1
	{% endif %}
	
	{% if mirror_priming %}
	
	
	
	{% if parking_position_t0|abs < parking_position_t1 - printable_x_max %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{printable_x_max + parking_position_t0|abs} F{(speed)}
	{% else %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{0 - (parking_position_t1 - printable_x_max)} F{(speed)}
	{% endif %}
	
	{% else %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1} MODE=PRIMARY
	G1 X{parking_position_inactive_t} F{(speed)}
	
	
	{% if act_t==1 %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{center_x / 2} F{(speed)}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"

[gcode_macro IDEX_PARK]
gcode = 
	
	PARK_TOOLHEAD

[gcode_macro PARK_TOOLHEAD]
gcode = 
	
	{% set idex_mode = 'none' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="PARK_TOOLHEAD" MSG="Parking T{act_t}.."
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set parking_position_inact_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set printable_y_min = printer["gcode_macro RatOS"].printable_y_min|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" and 'xy' in printer.toolhead.homed_axes %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% elif printer.toolhead.position.y|float < printable_y_min %}
	G1 Y{printable_y_min} F{speed}
	{% endif %}
	
	SAVE_GCODE_STATE NAME=_PARK_TOOLHEAD
	G90
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0.5
	
	
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_inact_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	
	SET_VELOCITY_LIMIT ACCEL={printer.toolhead.max_accel} MINIMUM_CRUISE_RATIO=0.5
	M400
	RESTORE_GCODE_STATE NAME=_PARK_TOOLHEAD
	
	{% endif %}

[gcode_macro JOIN_SPOOLS]
gcode = 
	
	{% set spools = params.SPOOLS|default("") %}
	
	{% if spools == "" %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% else %}
	{% if spools != "0,1" and spools != "1,0" %}
	RATOS_ECHO MSG="Wrong spool configuration!"
	RATOS_ECHO MSG="Join Spools = JOIN_SPOOLS SPOOLS=0,1"
	RATOS_ECHO MSG="Deactivate = JOIN_SPOOLS SPOOLS="
	{% else %}
	{% if spools == "0,1" or spools == "1,0" %}
	_IDEX_JOIN_SPOOLS ENABLE=true
	{% else %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_JOIN_SPOOLS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if enable %}
	{% set has_t0_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t1_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t0_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined else false %}
	{% set has_t1_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined else false %}
	{% if (has_t0_toolhead_filament_sensor and has_t1_toolhead_filament_sensor) or (has_t0_bowden_filament_sensor and has_t1_bowden_filament_sensor) %}
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=True
	RATOS_ECHO MSG="Spool joining enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Can not enable spool joining! No filament sensors found."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining deactivated!"
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining is not possible in copy and mirror mode!"
	{% endif %}

[gcode_macro _JOIN_SPOOL]
gcode = 
	
	{% set old_toolhead = params.TOOLHEAD|int %}
	{% set new_toolhead = 0 if old_toolhead == 1 else 1 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set purge_after_load = printer["gcode_macro T%s" % new_toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_JOIN_SPOOL" MSG="toolhead: {new_toolhead}"
	
	{% set has_filament = true %}
	{% set has_new_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% set has_new_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% if has_new_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	{% if has_new_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	
	{% if has_filament %}
	RATOS_ECHO MSG="Joining spools! Please wait for extruder to heat up...."
	
	
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={new_toolhead}
	
	
	_DEACTIVATE_TOOLHEAD TOOLHEAD={old_toolhead}
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set extruder_temp = extruder_first_layer_temp[new_toolhead]|float %}
	{% else %}
	{% set extruder_temp = extruder_other_layer_temp[new_toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if new_toolhead == 0 else 'extruder1'} TARGET={extruder_temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if new_toolhead == 0 else 'extruder1'} MINIMUM={extruder_temp}  MAXIMUM={extruder_temp + 5}
	
	
	{% if purge_after_load > 0 %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_toolhead == 0 else new_toolhead}
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={new_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={new_toolhead} E={purge_after_load}
	_CLEANING_MOVE TOOLHEAD={new_toolhead} AUTOMATED=True
	
	
	SET_DUAL_CARRIAGE CARRIAGE={old_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if old_toolhead == 0 else old_toolhead}
	
	{% endif %}
	
	
	RESUME TOOLHEAD={new_toolhead}
	
	
	_IDEX_JOIN_SPOOLS ENABLE=false
	
	{% else %}
	{ action_raise_error("Spool join failed! No filament found or filament sensor is disabled.") }
	{% endif %}

[gcode_macro REMAP_TOOLHEADS]
gcode = 
	
	{% set toolheads = params.TOOLHEADS|default("") %}
	
	{% if toolheads == "" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% else %}
	{% if toolheads != "0,1" and toolheads != "1,0" %}
	RATOS_ECHO MSG="Wrong toolhead configuration!"
	RATOS_ECHO MSG="Remap = REMAP_TOOLHEADS TOOLHEADS=0,1"
	RATOS_ECHO MSG="Deactivate = REMAP_TOOLHEADS TOOLHEADS="
	{% else %}
	{% if toolheads == "0,1" or toolheads == "1,0" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=true
	_IDEX_SINGLE
	{% else %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_REMAP_TOOLHEADS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	{% if not enable or (idex_mode != "copy" and idex_mode != "mirror") %}
	{% if enable %}
	RATOS_ECHO MSG="Toolhead remapping enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping deactivated!"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE={enable}
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping not possible in copy and mirror mode!"
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	{% endif %}

[gcode_macro SHAPER_CALIBRATE]
rename_existing = SHAPER_CALIBRATE_ORG
gcode = 
	RATOS_ECHO PREFIX="IDEX" MSG="SHAPER_CALIBRATE is useless on IDEX machines. Please use the GENERATE_SHAPER_GRAPHS macro and type the values into `variable_shaper_*_freq` and `variable_shaper_*_type manually`."

[gcode_shell_command generate_shaper_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-shaper-graph.sh
timeout = 120.
verbose = True

[gcode_shell_command generate_tension_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-belt-tension-graph.sh
timeout = 120.
verbose = True

[gcode_macro SET_PRESSURE_ADVANCE]
variable_snyc_toolheads = False
rename_existing = SET_PRESSURE_ADVANCE_BASE
gcode = 
	{% if params.SYNC_TOOLHEADS is defined %}
	{% set snyc_toolheads = true if params.SYNC_TOOLHEADS|default(false)|lower == 'true' else false %}
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=True
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="Syncing toolheads..."
	{% else %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' or snyc_toolheads %}
	{% set advance = params.ADVANCE|default(printer['extruder'].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['extruder'].smooth_time|float)|float %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T0"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T1"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder1' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% else %}
	{% set extruder = 'extruder' if act_t == 0 else 'extruder1' %}
	{% if params.EXTRUDER is defined %}
	{% set extruder = params.EXTRUDER %}
	{% endif %}
	{% if extruder == 'extruder' or extruder == 'extruder1' %}
	{% set advance = params.ADVANCE|default(printer['%s' % extruder].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['%s' % extruder].smooth_time|float)|float %}
	SET_PRESSURE_ADVANCE_BASE EXTRUDER={extruder} ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% if params.EXTRUDER is not defined %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG={"T%s" % act_t}
	{% endif %}
	{% else %}
	SET_PRESSURE_ADVANCE_BASE { rawparams }
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro M106]
rename_existing = M106.1
variable_swap_speed = -1
gcode = 
	
	{% set s = [[params.S|default(255)|int, 255]|min, 0]|max %}
	{% set p = params.P|default(-1)|int %}
	{% set speed = s / 255 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set t = 1 if idex_mode=='primary' else 0 %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(0)|int == 1 else false %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set sync_fans = true %}
	{% endif %}
	
	
	{% if sync_fans and idex_mode != "copy" and idex_mode != "mirror" %}
	
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int %}
	
	
	{% if toolshift_count > total_toolshifts %}
	{% set sync_fans = false %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE=-1
	
	
	{% if p == -1 %}
	
	{% if speed == 0 %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed}
	{% else %}
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE={speed}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={(speed if (t == 0 or sync_fans) else 0)}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={(speed if (t == 1 or sync_fans) else 0)}
	{% endif %}
	{% else %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed if t == p else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed if t == p else 0}
	{% endif %}
	
	
	M106.1 S{s}

[gcode_macro M107]
rename_existing = M107.1
gcode = 
	{% set p = params.P|default(-1)|int %}
	M106 S0 P{p}

[gcode_macro _SELECT_TOOL]
variable_last_timestamp = 0
gcode = 
	{% if params.T is defined %}
	{% set idex_mode = '' %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if "xyz" not in printer.toolhead.homed_axes and (idex_mode == "copy" or idex_mode == "mirror") %}
	_IDEX_SINGLE
	{% set idex_mode = 'reset' %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set new_t = params.T|int %}
	
	
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads and is_printing_gcode %}
	{% set new_t = 0 if new_t == 1 else 1 %}
	{% endif %}
	
	
	{% set toolchange_prepurging_timer = printer["gcode_macro RatOS"].toolchange_prepurging_timer|default(0)|int %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	DEBUG_ECHO PREFIX="_SELECT_TOOL" MSG="act_t: {act_t}, new_t: {new_t}, is_printing_gcode: {is_printing_gcode}, swap_toolheads: {swap_toolheads}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	{% set act_extruder = 'extruder%s' % ('' if new_t == 0 else new_t) %}
	{% if new_t != act_t or printer.toolhead.extruder != act_extruder or idex_mode == 'reset' %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Selecting T{new_t}.."
	
	
	M220 S100
	
	
	
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(1)|int == 1 else false %}
	
	
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set toolshift = false %}
	{% endif %}
	
	
	{% set fan_speed = printer["fan_generic part_fan_t%s" % act_t].speed %}
	
	
	{% set deactivate_toolhead = false %}
	{% if is_printing_gcode %}
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int + 1 %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE={toolshift_count}
	{% if toolshift_count == total_toolshifts %}
	{% set deactivate_toolhead = true %}
	{% endif %}
	{% endif %}
	
	
	{% set needs_wakeup = true if printer["gcode_macro T%s" % new_t].standby|default(false)|lower == 'true' else false %}
	
	
	{% set needs_purging = false %}
	{% set wake_up_purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% if is_printing_gcode and toolchange_prepurging_timer > 0 and wake_up_purge > 0 %}
	{% set new_timestamp = printer["print_stats"].print_duration %}
	{% set elapsed_time = new_timestamp - last_timestamp %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={new_timestamp}
	{% if elapsed_time > toolchange_prepurging_timer %}
	{% set needs_purging = true %}
	{% endif %}
	{% endif %}
	
	
	{% set first_use_purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% if toolshift_count == 1 and first_use_purge > 0 %}
	{% set needs_purging = true %}
	{% endif %}
	
	
	{% if is_printing_gcode and (toolchange_standby_temp > -1 or needs_purging or needs_wakeup) %}
	_TOOLHEAD_STANDBY TOOLHEAD={act_t}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	_TOOLHEAD_WAKEUP TOOLHEAD={new_t} X={new_x} Y={new_y} Z={new_z} FAN_SPEED={fan_speed} TOOLSHIFT_COUNT={toolshift_count}
	{% else %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(false)|lower == 'true' else false %}
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if (new_t == 0 or sync_fans) else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if (new_t == 1 or sync_fans) else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	_TOOLCHANGE T={new_t} X={new_x} Y={new_y} Z={new_z} PARK_T0={park_t0} PARK_T1={park_t1} TOOLSHIFT={toolshift}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[new_t]|float)} SHAPER_FREQ_Y={(shaper_y_freq[new_t]|float)} SHAPER_TYPE_X={(shaper_x_type[new_t]|lower)} SHAPER_TYPE_Y={(shaper_y_type[new_t]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if new_t == 0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if new_t == 1 else False}
	
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% set sanity_check_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if new_t == 0 %}
	{% if printer.toolhead.extruder == 'extruder' %}
	{% if sanity_check_idex_mode == 'primary' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% elif new_t == 1 %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% if sanity_check_idex_mode == 'inactive' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _TOOLHEAD_STANDBY]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Putting toolhead T{toolhead} into standby mode."
	DEBUG_ECHO PREFIX="_TOOLHEAD_STANDBY" MSG="toolhead: {toolhead}, config_z_hop: {config_z_hop}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={toolhead} SYNC=0
	PARK_TOOLHEAD
	
	
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={toolchange_standby_temp}
	{% endif %}
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=True
	{% endif %}
	
	
	_LED_TOOLHEAD_STANDBY TOOLHEAD={toolhead}

[gcode_macro _TOOLHEAD_WAKEUP]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set fan_speed = params.FAN_SPEED|float %}
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift_count = params.TOOLSHIFT_COUNT|default(0)|int %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% if toolshift_count == 1 %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% endif %}
	{% set needs_wakeup = true if printer["gcode_macro T%s" % toolhead].standby|default(false)|lower == 'true' else false %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Waking up toolhead T{toolhead}. Please wait for extruder to heat up..."
	DEBUG_ECHO PREFIX="_TOOLHEAD_WAKEUP" MSG="toolhead: {toolhead}, fan_speed: {fan_speed}, new_x: {new_x}, new_y: {new_y}, new_z: {new_z}, config_z_hop: {config_z_hop}"
	
	
	_LED_TOOLHEAD_WAKEUP TOOLHEAD={toolhead}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={toolhead} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE=1
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if toolhead == 0 else toolhead}
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if needs_wakeup %}
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set temp = extruder_first_layer_temp[toolhead]|float %}
	{% else %}
	{% set temp = extruder_other_layer_temp[toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if toolhead == 0 else 'extruder1'} MINIMUM={temp}  MAXIMUM={temp + 5}
	{% endif %}
	
	
	_LED_PRINTING TOOLHEAD={toolhead}
	
	
	{% if purge > 0 %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={toolhead} E={purge}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	
	
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if toolhead == 1 else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	G92 E0
	G1 E-{e} F{feedrate}
	G92 E0
	
	
	{% if new_x >= 0 and new_y >= 0 %}
	G1 X{new_x} Y{new_y} F{speed}
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={config_z_hop} T={toolhead} SYNC=0
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=False

[gcode_macro _TOOLCHANGE]
variable_toolshift_count = 0
gcode = 
	
	
	{% set new_t = params.T|default(-1)|int %}
	{% set new_x = params.X|default(-1.0)|float %}
	{% set new_y = params.Y|default(-1.0)|float %}
	{% set new_z = params.Z|default(-1.0)|float %}
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(true)|lower == 'true' else false %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T: {new_t}, X: {new_x}, Y: {new_y}, Z: {new_z}, PARK_T0: {park_t0}, PARK_T1: {park_t1}, IS_PRINTING_GCODE: {is_printing_gcode}, TOOLSHIFT: {toolshift}"
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	{% if park_t0 >= 0 and park_t1 >= 0 %}
	{% set parking_position_t0 = park_t0 %}
	{% set parking_position_t1 = park_t1 %}
	{% set parking_position_act_t = park_t0 if act_t == 0 else park_t1 %}
	{% endif %}
	
	
	{% if not is_printing_gcode and not toolshift %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Changing tool to T{new_t} without retracting/extruding or moving the toolheads except for parking."
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	G90
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% if not is_printing_gcode and toolshift and new_x < 0 and new_y < 0 %}
	{% set new_x = center_x %}
	{% set new_y = printer.gcode_move.gcode_position.y|float %}
	{% endif %}
	
	{% if new_x < 0 or new_y < 0 %}
	
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="No new X or Y position given, parking the active toolhead and activating the new toolhead without moving it."
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={new_t}
	
	
	{% if "x" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	{% if is_printing_gcode %}
	_EXTRUDE T={new_t}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	{% if "xyz" not in printer.toolhead.homed_axes %}
	
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	
	
	{% set svv = printer.save_variables.variables %}
	{% if new_t == default_toolhead %}
	{% set new_xoffset = 0 %}
	{% set new_yoffset = 0 %}
	{% set new_zoffset = 0 %}
	{% else %}
	{% set new_xoffset = -svv.idex_xoffset %}
	{% set new_yoffset = -svv.idex_yoffset %}
	{% set new_zoffset = -svv.idex_zoffset %}
	{% endif %}
	
	{% set xoffset_correction = new_xoffset - printer.named_offsets.toolhead_alignment.x %}
	{% set yoffset_correction = new_yoffset - printer.named_offsets.toolhead_alignment.y %}
	{% set zoffset_correction = new_zoffset - printer.named_offsets.toolhead_alignment.z %}
	
	{% if new_t == 0 %}
	
	{% set t0_act_x = parking_position_t0 %}
	{% set t1_act_x = printer.toolhead.position.x|float %}
	{% set t0_new_x = new_x %}
	{% set t1_new_x = parking_position_t1 %}
	{% set t0_distance = t0_new_x - t0_act_x %}
	{% set t1_distance = t1_new_x - t1_act_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T0."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	
	
	G1 X{t0_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x + (t1_new_x - t1_act_x)} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t0_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T0: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% elif new_t == 1 %}
	
	{% set t0_act_x = printer.toolhead.position.x|float %}
	{% set t1_act_x = parking_position_t1 %}
	{% set t0_new_x = parking_position_t0 %}
	{% set t1_new_x = new_x %}
	{% set t0_distance = t0_act_x - t0_new_x %}
	{% set t1_distance = t1_act_x - t1_new_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T1."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x - t1_distance + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t1_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T1: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% endif %}
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	{% endif %}

[gcode_macro _ZHOP_BEFORE_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_hop = params.Z_HOP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_HOP: {z_hop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="COMBINED_ZHOP G1 Z+{z_hop} E-{e} F{speed * 60}"
	G1 Z+{z_hop} E-{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="ZHOP G1 Z+{z_hop} F{speed * 60}"
	G1 Z+{z_hop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="RETRACT G1 E-{e} F{feedrate}"
	G1 E-{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _ZDROP_AFTER_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_drop = params.Z_DROP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_DROP: {z_drop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="COMBINED_ZDROP G1 Z-{z_drop} E{e} F{speed * 60}"
	G1 Z-{z_drop} E{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="ZDROP G1 Z-{z_drop} F{speed * 60}"
	G1 Z-{z_drop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="EXTRUDE G1 E{e} F{feedrate}"
	G1 E{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _EXTRUDE]
gcode = 
	
	{% set t = params.T|int %}
	
	
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	
	DEBUG_ECHO PREFIX="_EXTRUDE" MSG="G1 E{e} F{feedrate * 60}"
	
	
	G91
	M82
	G92 E0
	G1 E{e} F{feedrate * 60}
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _DEACTIVATE_TOOLHEAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_DEACTIVATE_TOOLHEAD" MSG="TOOLHEAD {toolhead}"
	
	
	{% if toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% endif %}
	
	
	M106.1 S0
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={toolhead}

[delayed_gcode _INIT_TOOLHEADS]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	_IDEX_SINGLE INIT=1
	
	
	{% if printer.fastconfig.settings.dual_carriage.safe_distance is defined %}
	{% if printer.fastconfig.settings.dual_carriage.safe_distance|float < 50 %}
	{ action_emergency_stop("Dual carriage safe_distance seems to be too low!") }
	{% endif %}
	{% else %}
	{ action_emergency_stop("Dual carriage safe_distance not defined!") }
	{% endif %}

[gcode_macro _SET_TOOLHEAD_OFFSET]
description = "Internal use only. Sets the toolhead_alignment offset (and hotend_thermal_expansion offset when configured) for the active/dominant toolhead."
gcode = 
	
	{% set move = params.MOVE|default(0)|int %}
	{% set force_toolhead = params.FORCE_TOOLHEAD|default(-1)|int %}
	
	
	{% if params.T is defined %}
	CONSOLE_ECHO TYPE="error" MSG="_SET_TOOLHEAD_OFFSET called with deprectated T parameter, which is ignored."
	{';$_SET_TOOLHEAD_OFFSET_ignoring_TOOLHEAD_parameter'}
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="active/dominant toolhead: {toolhead}, MOVE: {move}, FORCE_TOOLHEAD: {force_toolhead}"
	
	
	{% if force_toolhead >= 0 %}
	{% set toolhead = force_toolhead %}
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="FORCE_TOOLHEAD applied, using TOOLHEAD: {toolhead}"
	{% endif %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set move = 0 %}
	{% endif %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|int %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X=0 Y=0 MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z=0 MOVE={move} SPEED={z_speed}
	{% else %}
	{% set svv = printer.save_variables.variables %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X={(-svv.idex_xoffset)} Y={(-svv.idex_yoffset)} MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-svv.idex_zoffset)} MOVE={move} SPEED={z_speed}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}

[gcode_macro TOOLSHIFT_CONFIG]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={params.SPEED|default(300)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={params.ACCEL|default(5000)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_retraction VALUE={params.RETRACT|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_extrusion VALUE={params.EXTRUDE|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_feedrate VALUE={params.FEEDRATE|default(7200)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={params.Z_HOP|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zspeed VALUE={params.Z_SPEED|default(25)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_combined_zhop VALUE={true if params.COMBINED_ZHOP|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_sync_fans VALUE={true if params.SYNC_FANS|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_prepurging_timer VALUE={params.AUTO_PURGE_TIME|default(0)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_purge VALUE={params.PURGE|default(25)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_standby_temp VALUE={params.STANDBY_TEMP|default(-1)|float}

[gcode_macro CALCULATE_DC_ENDSTOP]
description = "DEPRECATED: This macro has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."
gcode = 
	CONSOLE_ECHO TITLE="CALCULATE_DC_ENDSTOP has been deprecated" TYPE="error" MSG="The CALCULATE_DC_ENDSTOP has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."

[gcode_macro _VAOC]
variable_is_fixed = True
variable_is_started = False
variable_is_started_at_temp = False
variable_additional_safe_distance = 50
variable_safe_z = 30
variable_auto_z_offset_calibration = True
variable_enable_camera_cooling = True
variable_camera_cooling_fan_speed = 0.3
variable_camera_cooling_temperature = 50
variable_toolchange_travel_speed = 300
variable_toolchange_travel_accel = 5000
variable_adjusting_secondary_toolhead_focus_adjusts_zoffset = False
variable_cache_toolchange_travel_speed = 300
variable_cache_toolchange_travel_accel = 5000
variable_cache_toolchange_zhop = 1.0
variable_t0_toolhead_sensor_enabled = 0
variable_t1_toolhead_sensor_enabled = 0
variable_t0_bowden_sensor_enabled = 0
variable_t1_bowden_sensor_enabled = 0
variable_loaded_skew_profile = ""
variable_gcode_z_offset = 0.0
variable_start_x_offset = 0.0
variable_start_y_offset = 0.0
gcode = 
	_ECHO_VAOC_VARS
variable_expected_camera_x_position = 212.5
variable_expected_camera_y_position = 530.5

[gcode_macro _VAOC_START]
description = Called from the front end. If T0_TEMP, T1_TEMP and BED_TEMP parameter are specified, VAOC calibration will start under real conditions at printing temp.
gcode = 
	
	{% set t0_temp = params.T0_TEMP|default(0)|int %}
	{% set t1_temp = params.T1_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(0)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro SKEW_PROFILE"].loaded_profile|default("") %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=loaded_skew_profile VALUE='"{loaded_skew_profile}"'
	
	
	{% if t0_temp > 0 and t1_temp > 0 and bed_temp > 0 %}
	
	
	{% if not is_fixed %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("VAOC calibration at temp works only with a fixed installed VAOC device.") }
	{% endif %}
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE=0
	{% endif %}
	
	
	START_PRINT EXTRUDER_TEMP={t0_temp},{t1_temp} EXTRUDER_OTHER_LAYER_TEMP={t0_temp},{t1_temp} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp} INITIAL_TOOL=0 TOTAL_LAYER_COUNT=1 X0={(printable_x_max / 2 - 10)} Y0={(printable_y_max / 2 - 10)} X1={(printable_x_max / 2 + 10)} Y1={(printable_y_max / 2 + 10)} TOTAL_TOOLSHIFTS=1 FIRST_X={printable_x_max / 2} FIRST_Y={printable_y_max / 2} MIN_X={(printable_x_max / 2 - 10)} MAX_X={(printable_x_max / 2 + 10)} USED_TOOLS=0,1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=True
	
	{% endif %}
	
	
	_START_VAOC

[gcode_macro _START_VAOC]
description = Called from _VAOC_START. Do not call it manually.
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(printable_x_max/2)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(printable_y_max/2)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	DEBUG_ECHO PREFIX="VAOC_START" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, zcontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_x_offset VALUE={svv.idex_xoffset|default(0.0)|float}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_y_offset VALUE={svv.idex_yoffset|default(0.0)|float}
	
	
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_SAFE_Z_HEIGHT
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_speed VALUE={printer["gcode_macro RatOS"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_accel VALUE={printer["gcode_macro RatOS"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_zhop VALUE={printer["gcode_macro RatOS"].toolchange_zhop|float}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE=0
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"START X_REFERENCE:%.6f Y_REFERENCE:%.6f Z_REFERENCE:%.6f PARK_T0:%.6f PARK_T1:%.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, parking_position_t0, parking_position_t1)}
	
	
	_LED_VAOC_ON
	
	
	
	
	
	
	
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=gcode_z_offset VALUE={printer.gcode_move.homing_origin.z}
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z=0
	
	
	MAYBE_HOME
	M400
	
	
	_LOAD_RATOS_SKEW_PROFILE
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	IDEX_SINGLE
	{% endif %}
	
	
	
	SAVE_GCODE_STATE NAME=vaoc_state
	
	
	RESET_NAMED_OFFSET EVENT=reset_all
	
	
	{% if is_fixed %}
	_SELECT_TOOL T=0 TOOLSHIFT=false
	{% if default_toolhead == 0 %}
	G1 X{idex_xcontrolpoint} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint + safe_distance + additional_safe_distance} F{speed}
	{% else %}
	G1 X{idex_xcontrolpoint - safe_distance - additional_safe_distance} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint} F{speed}
	{% endif %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	{% else %}
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	G1 X{idex_xcontrolpoint} F{speed}
	G1 Y{idex_ycontrolpoint} F{speed}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	
	
	_SELECT_TOOL T={default_toolhead} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	{% if not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={default_toolhead}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=True

[gcode_macro _VAOC_END]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_y = printable_y_max / 2 %}
	{% set saved_gcode_z_offset = printer["gcode_macro _VAOC"].gcode_z_offset|default(0.0)|float %}
	
	DEBUG_ECHO PREFIX="_VAOC_END" MSG="printable_y_max: {printable_y_max}, center_y: {center_y}, safe_z: {safe_z}"
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% set x_offset_change = svv.idex_xoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_x_offset|default(0.0)|float %}
	{% set y_offset_change = svv.idex_yoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_y_offset|default(0.0)|float %}
	{% set offset_change_norm = (x_offset_change ** 2 + y_offset_change ** 2) ** 0.5 %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="VAOC calibration changed the relative XY offset between T0 and T1 by {offset_change_norm|round(3)} mm (ΔX: {x_offset_change|round(3)}, ΔY: {y_offset_change|round(3)})"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	G1 Y{center_y} F{speed}
	
	
	_IDEX_SINGLE INIT=1
	
	
	_LED_VAOC_OFF
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={printer["gcode_macro _VAOC"].cache_toolchange_zhop|float}
	
	
	{% if printer["gcode_macro _VAOC"].is_started_at_temp|default(true)|lower == 'true' %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_bowden_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_bowden_sensor_enabled|int}
	{% endif %}
	{% endif %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro _VAOC"].loaded_skew_profile|default("") %}
	{% if loaded_skew_profile != "" %}
	SKEW_PROFILE LOAD={loaded_skew_profile}
	{% else %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=vaoc_state
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z={saved_gcode_z_offset}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False

[gcode_macro _VAOC_LOAD_TOOL]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set auto_temp_offset = true if params.AUTO_TEMP_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set toolhead_zoffset = svv.idex_zoffset|default(0)|float %}
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move T%s to control point: X%.6f Y%.6f Z%.6f IS_FIXED=%s"' % (t, idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, is_fixed)}
	
	
	{% if not auto_temp_offset and not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={t}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	{% set current_z = printer.toolhead.position.z|float %}
	{% set lowest_toolhead_z = [current_z, current_z - toolhead_zoffset]|min %}
	{% if lowest_toolhead_z < safe_z %}
	G1 Z{[safe_z, safe_z + toolhead_zoffset]|max} F{z_speed}
	{% else %}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	{% endif %}
	
	
	_SELECT_TOOL T={t} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_SET_CAMERA_COOLING]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	
	
	{% set enable_camera_cooling = true if printer["gcode_macro _VAOC"].enable_camera_cooling|default(true)|lower == 'true' else false %}
	{% set camera_cooling_temperature = printer["gcode_macro _VAOC"].camera_cooling_temperature|float %}
	{% set camera_cooling_fan_speed = printer["gcode_macro _VAOC"].camera_cooling_fan_speed|float %}
	
	
	{% if printer.heater_bed.temperature >= camera_cooling_temperature and enable_camera_cooling %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={camera_cooling_fan_speed if t == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={camera_cooling_fan_speed if t == 1 else 0}
	
	
	M106.1 S{camera_cooling_fan_speed}
	
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	{% endif %}

[gcode_macro _VAOC_SET_TOOL]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="_VAOC_SET_TOOL" MSG="IDEX_MODE: {idex_mode}, TOOLHEAD: {toolhead}"
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	{% set x = printer.gcode_move.gcode_position.x|float %}
	{% set y = printer.gcode_move.gcode_position.y|float %}
	{% set z = printer.gcode_move.gcode_position.z|float %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE={x}
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE={y}
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE={z}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Control point was set: X%.6f Y%.6f Z%.6f"' % (x, y, z)}
	
	{% else %}
	
	
	
	{% set move_diff_x = printer.gcode_move.gcode_position.x|float - svv.idex_xcontrolpoint|float %}
	{% set move_diff_y = printer.gcode_move.gcode_position.y|float - svv.idex_ycontrolpoint|float %}
	{% set move_diff_z = printer.gcode_move.gcode_position.z|float - svv.idex_zcontrolpoint|float %}
	
	
	{% set new_x_offset = svv.idex_xoffset - move_diff_x %}
	{% set new_y_offset = svv.idex_yoffset - move_diff_y %}
	{% set new_z_offset = svv.idex_zoffset - move_diff_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE={new_x_offset}
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE={new_y_offset}
	
	{% set z_focus_msg = "" %}
	{% if move_diff_z|abs > 1e-6 %}
	{% if printer["gcode_macro _VAOC"].adjusting_secondary_toolhead_focus_adjusts_zoffset|default(false)|lower == 'true' %}
	{% set z_focus_msg = " (Z offset adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={new_z_offset}
	{% else %}
	{% set z_focus_msg = " (Z offset not adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	{% set new_z_offset = svv.idex_zoffset %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset was set: X%.6f Y%.6f Z%.6f%s"' % (toolhead, new_x_offset, new_y_offset, new_z_offset, z_focus_msg)}
	
	{% endif %}

[gcode_macro _VAOC_MOVE]
gcode = 
	
	{% set x = params.X|default(0)|float %}
	{% set y = params.Y|default(0)|float %}
	{% set z = params.Z|default(0)|float %}
	
	
	G91
	{% if z != 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 Z%.6f F300"' % (z)}
	G1 Z{z} F300
	
	{% else %}
	{% if x <=2 and y <=2 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 X%.6f Y%.6f F18000"' % (x, y)}
	G1 X{x} Y{y} F18000
	{% endif %}
	{% endif %}
	G90

[gcode_macro _VAOC_CALIBRATE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	{% if printer["z_offset_probe"] is defined and is_started %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	
	{% if auto_z_offset %}
	_START_VAOC AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_END
	{% else %}
	_VAOC_LOAD_TOOL T={default_toolhead}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	{% endif %}
	
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_Z_OFFSET
	
	{% endif %}

[gcode_macro _VAOC_PROBE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}
	{% if not auto_z_offset %}
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	{% endif %}
	M400
	_VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT

[gcode_macro _VAOC_Z_OFFSET_PROBE_CURRENT_POSITION]
gcode = 
	
	Z_OFFSET_PROBE PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_DROP=1 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median

[gcode_macro _VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT]
gcode = 
	{% if printer["z_offset_probe"] is defined %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE={last_z}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Z-offset control point set:: %.6f"' % last_z}
	
	{% else %}
	
	
	
	{% set z = svv.idex_zoffsetcontrolpoint|float - last_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={z}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-z)}
	
	
	G0 Z{svv.idex_zcontrolpoint|float} F{z_speed}
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset set: Z %.6f"' % (t, z)}
	
	{% endif %}
	
	{% endif %}

[gcode_macro _VAOC_ECHO_Z_OFFSET]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s toolhead z-offset %.6f"' % (1 if default_toolhead == 0 else 0, svv.idex_zoffset)}
	{% if svv.idex_zoffset|abs < 0.02 %}
	CONSOLE_ECHO TITLE={'"Perfect toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="You have a perfect toolhead z-offset!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.02 and svv.idex_zoffset|abs < 0.05 %}
	CONSOLE_ECHO TITLE={'"Good toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is good!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.05 and svv.idex_zoffset|abs < 0.1 %}
	CONSOLE_ECHO TITLE={'"High toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset could be better._N_Use minimum 0.3mm first layer height for copy and mirror mode prints." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.1 and svv.idex_zoffset|abs < 0.2 %}
	CONSOLE_ECHO TITLE={'"Bad toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is bad._N_Copy and mirror mode prints are not recommended with it." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.2 %}
	CONSOLE_ECHO TITLE={'"Unacceptable toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is unacceptable._N_Do not print in copy and mirror mode with it." TYPE="alert"
	{% endif %}
	RATOS_ECHO PREFIX="VAOC" MSG="Toolhead z-offset calibration done!"

[gcode_macro _VAOC_CALIBRATE_TEMP_OFFSET]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if is_fixed and is_started and printer["z_offset_probe"] is defined and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	_VAOC_LOAD_TOOL T={default_toolhead} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_NOZZLE_TEMP_OFFSETS
	
	{% endif %}

[gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET=0
	
	
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	M400

[gcode_macro _VAOC_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(150)|float %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Probing with nozzle temperature {temp}°C..."
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	
	
	G0 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _VAOC_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set msg = '"T0 expansion coefficient %.6fmm_N_T1 expansion coefficient %.6fmm"' % (svv.nozzle_expansion_coefficient_t0, svv.nozzle_expansion_coefficient_t1) %}
	CONSOLE_ECHO TITLE="Nozzle expansion coefficients:" MSG={msg} TYPE="success"

[gcode_macro _VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - expected_camera_x_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC x-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_xcontrolpoint, expected_camera_x_position)) }
	{% endif %}
	{% if (idex_ycontrolpoint - expected_camera_y_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC y-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_ycontrolpoint, expected_camera_y_position)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - printer.gcode_move.gcode_position.x|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected y-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_xcontrolpoint, printer.gcode_move.gcode_position.x|float)) }
	{% endif %}
	{% if (idex_ycontrolpoint - printer.gcode_move.gcode_position.y|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected x-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_ycontrolpoint, printer.gcode_move.gcode_position.y|float)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_SAFE_Z_HEIGHT]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set idex_zoffsetcontrolpoint = svv.idex_zoffsetcontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_SAFE_Z_HEIGHT" MSG={'"idex_zcontrolpoint: %.6f, idex_zoffsetcontrolpoint: %.6f"' % (idex_zcontrolpoint, idex_zoffsetcontrolpoint)}
	
	{% if safe_z < idex_zcontrolpoint + 2 or safe_z < idex_zoffsetcontrolpoint + 2 %}
	{action_raise_error("VAOC safe_z value (%.3f) is too low, it must be higher than %.3f" % (safe_z, [idex_zoffsetcontrolpoint + 2, idex_zcontrolpoint + 2]|max))}
	{% endif %}

[gcode_macro _VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED]
gcode = 
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T0. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T1. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_RESET]
gcode = 
	DEBUG_ECHO PREFIX="_VAOC_RESET" MSG="running template-emitted _VAOC_RESET macro"
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE=212.5
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE=530.5
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE=10
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE=0
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE=0.0
	
	RESET_DC_ENDSTOP_CONFIGURATION
	RESET_Y_MAX_ADJUSTMENT
	
	
	CONSOLE_ECHO TITLE="VAOC Configuration Reset" MSG="VAOC configuration has been reset. You must RESTART klipper for the changes to take effect,_N_then re-calibrate VAOC."

[gcode_macro _ECHO_VAOC_VARS]
description = Echo VAOC variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro _VAOC"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro _VAOC_SWITCH_LED]
gcode = 
	{% if params.STATE|default(0)|int == 1 %}
	_LED_VAOC_ON
	{% else %}
	_LED_VAOC_OFF
	{% endif %}

[gcode_macro Z_PROBE_TEST_T0]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T0
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST_T1]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T1
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	
	
	_VAOC_Z_PROBE_TEST_EVALUATE
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro _VAOC_Z_PROBE_LOOP]
gcode = 
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_SHAKE_IT
	_VAOC_START

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if primary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T0. Retried {primary_retries} time(s)."
	{% endif %}
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	
	{% if (primary_range - secondary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 is drifting significantly more than T1."
	{% endif %}
	{% if (secondary_range - primary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 is drifting significantly more than T0."
	{% endif %}
	
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T0]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T1]
gcode = 
	
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _SHAKE_IT]
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	_Z_HOP
	{% for i in range(3) %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 + 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 + 1}
	{% endfor %}
	{% for i in range(2) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 + 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 + 50}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 1}
	{% endfor %}
	{% endfor %}

[gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 retries updated: {new_retries}"

[gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 retries updated: {new_retries}"

[gcode_macro _CLEAR_PRIMARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _CLEAR_SECONDARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _VAOC_TEST_Z_OFFSET]
gcode = 
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}

[delayed_gcode _IDEX_INIT]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	VERIFY_HYBRID_INVERTED

[gcode_macro Z_TILT_ADJUST]
rename_existing = Z_TILT_ADJUST_ORIG
gcode = 
	
	{% set beacon_contact_z_tilt_adjust_samples = printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust_samples|default(2)|int %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(true)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	_IDEX_SINGLE
	
	_SELECT_TOOL T={printer["gcode_macro RatOS"].default_toolhead|default(0)|int} TOOLSHIFT=false
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_tilt_adjust %}
	Z_TILT_ADJUST_ORIG PROBE_METHOD=contact SAMPLES={beacon_contact_z_tilt_adjust_samples}
	{% else %}
	Z_TILT_ADJUST_ORIG
	{% endif %}
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if idex_mode == "copy" %}
	_IDEX_COPY
	{% elif idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[stepper_x]
position_max = 500
position_endstop = -59.6
position_min = -59.6
step_pin = PF13
dir_pin = x_dir_pin
enable_pin = !PF14
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t0:PA2

[stepper_y]
position_max = 533.65
position_min = -14.35
position_endstop = -14.35
step_pin = PG0
dir_pin = !y_dir_pin
enable_pin = !PF15
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = PG9

[stepper_z]
position_max = 500
position_min = -7
step_pin = PC13
dir_pin = !z0_dir_pin
enable_pin = !PF1
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4
homing_speed = 10
endstop_pin = probe:z_virtual_endstop

[z_tilt]
z_positions = 
	0,0
	250,500
	500,0
points = 
	20, 10
	480, 230
	20, 450
horizontal_move_z = 20
retries = 10
retry_tolerance = 0.02
speed = 600

[extruder]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t0:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t0:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t0:PD3
dir_pin = toolboard_t0:e_dir_pin
enable_pin = !toolboard_t0:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[firmware_retraction]
retract_speed = 60
unretract_extra_length = 0
unretract_speed = 60
retract_length = 0.2

[extruder1]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t1:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t1:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t1:PD3
dir_pin = toolboard_t1:e_dir_pin
enable_pin = !toolboard_t1:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[resonance_tester]
accel_chip_x = lis2dw toolboard_t0
accel_chip_y = lis2dw toolboard_t0
probe_points = 
	250,250,20

[tmc5160 stepper_x]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC4
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 dual_carriage]
stealthchop_threshold = 0
interpolate = True
cs_pin = PF2
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y]
stealthchop_threshold = 0
interpolate = True
cs_pin = PD11
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y1]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC7
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[stepper_y1]
step_pin = PG4
dir_pin = y1_dir_pin
enable_pin = !PA2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46

[tmc2209 stepper_z]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE4
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[tmc2209 stepper_z1]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE1
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z1]
step_pin = PE2
dir_pin = !z1_dir_pin
enable_pin = !PD4
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 stepper_z2]
stealthchop_threshold = 0
interpolate = True
uart_pin = PD3
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z2]
step_pin = PE6
dir_pin = !z2_dir_pin
enable_pin = !PE0
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 extruder]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t0:PB3
run_current = 0.707
sense_resistor = 0.11

[tmc2209 extruder1]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t1:PB3
run_current = 0.707
sense_resistor = 0.11

[beacon]
serial = /dev/beacon
x_offset = 0
y_offset = 27.5
mesh_main_direction = x
mesh_runs = 1
mesh_cluster_size = 0
speed = 15.
lift_speed = 80.
contact_max_hotend_temperature = 275
contact_mesh_min = 20,20
contact_mesh_max = 480,480

[beacon_user_z_offset]

[beacon_mesh]

[beacon_true_zero_correction]

[beacon_adaptive_heat_soak]

[delayed_gcode _BEACON_INIT]
initial_duration = 1
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	_BEACON_MESH_INIT
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_coefficient_multiplier
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_applied_offset
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=beacon_saved_runtime_offset
	{% if printer["gcode_macro RatOS"].beacon_contact_expansion_multiplier is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_contact_expansion_multiplier is no longer used, please remove it from your config file."
	{% endif %}
	{% if printer["gcode_macro RatOS"].beacon_scan_compensation_resolution is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_scan_compensation_resolution is no longer used, please remove it from your config file."
	{% endif %}

[gcode_macro BEACON_RATOS_CALIBRATION]
gcode = 
	RATOS_ECHO MSG="Did you mean BEACON_RATOS_CALIBRATE?"

[gcode_macro BEACON_RATOS_CALIBRATE]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	BEACON_INITIAL_CALIBRATION _AUTOMATED=True
	
	{% if beacon_contact_start_print_true_zero %}
	BEACON_POKE_TEST _AUTOMATED=True
	_BEACON_CHECK_POKE
	{% if printer["dual_carriage"] is not defined %}
	BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET _AUTOMATED=True
	{% endif %}
	{% endif %}
	
	{% set already_heated = False %}
	
	
	{% if beacon_contact_start_print_true_zero and beacon_scan_compensation_enable %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% set already_heated = True %}
	{% endif %}
	
	
	BEACON_FINAL_CALIBRATION _AUTOMATED=True _AUTOMATED_ALREADY_HEATED={already_heated} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	{% if beacon_contact_start_print_true_zero %}
	{% if printer["dual_carriage"] is not defined %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	_BEACON_ECHO_POKE
	{% endif %}
	RATOS_ECHO MSG="Beacon calibration finished!"
	
	
	_LED_BEACON_CALIBRATION_END
	
	
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG

[gcode_macro BEACON_INITIAL_CALIBRATION]
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Initial beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro BEACON_FINAL_CALIBRATION]
description = Runs BEACON_AUTO_CALIBRATE after heating the bed and chamber to specified temperatures. This creates a beacon model under reference conditions for future use.
	This macro will skip calibration if both the beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero settings are enabled, because a new
	model will be calibrated automatically at the start of each print. Use FORCE=True to override this check.
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set already_heated = true if params._AUTOMATED_ALREADY_HEATED|default(false)|lower == 'true' else false %}
	{% set force = params.FORCE|default('false')|lower in ('1', 'true', 'yes') %}
	
	
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default('false')|lower == "true" %}
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero and not force %}
	RATOS_ECHO MSG="BEACON_FINAL_CALIBRATION skipped, not needed because beacon_contact_calibrate_model_on_true_zero is enabled. Use FORCE=True to override."
	{% else %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	{% if chamber_temp > 0 and not already_heated %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	{% if not already_heated %}
	
	G0 Z2.5 F{z_hop_speed}
	
	
	RATOS_ECHO MSG="Waiting for calibration temperature..."
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	{% if beacon_adaptive_heat_soak %}
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,3600]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_Z_HOP
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Final beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	{% endif %}

[gcode_macro BEACON_POKE_TEST]
variable_poke_result_1 = -1
variable_poke_result_2 = -1
variable_poke_result_3 = -1
variable_poke_result_4 = -1
variable_poke_result_5 = -1
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_1 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_2 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_3 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_4 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_5 VALUE=-1
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G0 Z5 F{z_hop_speed}
	
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=1
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=2
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=3
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=4
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=5
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Beacon poke test finished!"
	{% if not automated %}
	_BEACON_ECHO_POKE
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro _BEACON_PROBE_POKE]
gcode = 
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	BEACON_POKE speed=3 top=5 bottom={poke_bottom}
	BEACON_QUERY

[gcode_macro _BEACON_STORE_POKE]
gcode = 
	
	{% set i = params.I|default(1)|int %}
	
	
	{% set last_z = printer.beacon.last_poke_result|default(0)|float %}
	
	
	{% if printer.beacon.last_poke_result|lower != "none" %}
	{% if printer.beacon.last_poke_result.error == 0 %}
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE={"poke_result_%s" % i} VALUE={printer.beacon.last_poke_result.latency}
	{% endif %}
	{% endif %}

[gcode_macro _BEACON_CHECK_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% if p1 == -1 or p2 == -1 or p3 == -1 or p4 == -1 or p5 == -1 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test error!") }
	{% endif %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	{% if avg > 6 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test failed!") }
	{% endif %}

[gcode_macro _BEACON_ECHO_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	
	
	{% if avg <= 1 %}
	{% set type = "success" %}
	{% set note = "Extremely low noise, rarely achieved" %}
	{% elif avg > 1 and avg <= 4 %}
	{% set type = "info" %}
	{% set note = "Excellent performance for a typical printer" %}
	{% elif avg > 4 and avg <= 8 %}
	{% set type = "warning" %}
	{% set note = "Acceptable performance, machine may have considerable cyclic axis noise" %}
	{% elif avg > 8 and avg <= 11 %}
	{% set type = "alert" %}
	{% set note = "Not ideal, may want to verify proper mounting or use thinner stackups" %}
	{% elif avg > 11 %}
	{% set type = "alert" %}
	{% set note = "Reason for concern, present setup may be risky to continue with" %}
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon poke test result:" TYPE={type} MSG={'"Average latency: %.2f_N_%s"' % (avg, note)}

[gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Nozzle temperature offset calibration..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET=0
	
	
	{% if not automated %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing with nozzle temperature {temp}°C..."
	PROBE PROBE_METHOD=contact PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median
	BEACON_QUERY
	
	
	G0 Z5 F{z_speed}

[gcode_macro _BEACON_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer.beacon.last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{default_toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% if default_toolhead == 0 %}
	CONSOLE_ECHO TYPE="info" MSG={'"T0 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t0}
	{% else %}
	CONSOLE_ECHO TYPE="info" MSG={'"T1 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t1}
	{% endif %}

[gcode_macro _BEACON_SET_NOZZLE_TEMP_OFFSET]
description = "Set the thermal expansion z offset for the active toolhead based on the current extruder target temperature and thermal expansion coefficient."
gcode = 
	{% if params.RESET is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The RESET parameter is no longer supported and has no effect."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% if params.TOOLHEAD is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The TOOLHEAD parameter is no longer supported and has no effect. The macro now automatically determines the current toolhead."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	{% if beacon_contact_expansion_compensation %}
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set nozzle_expansion_coefficient_t0 = svv.nozzle_expansion_coefficient_t0|default(0)|float %}
	{% if printer["dual_carriage"] is defined %}
	{% set nozzle_expansion_coefficient_t1 = svv.nozzle_expansion_coefficient_t1|default(0)|float %}
	{% endif %}
	
	
	{% set temp = printer['extruder' if toolhead == 0 else 'extruder1'].target|float %}
	
	
	{% set temp_delta = temp - beacon_contact_true_zero_temp %}
	{% set expansion_coefficient = nozzle_expansion_coefficient_t0 if toolhead == 0 else nozzle_expansion_coefficient_t1 %}
	{% set expansion_offset = temp_delta * (expansion_coefficient / 100) %}
	
	
	SET_NAMED_OFFSET NAME=hotend_thermal_expansion Z={expansion_offset} MOVE=1 MOVE_SPEED={z_speed}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG={'"Nozzle expansion offset of %.6fmm applied to T%s"' % (expansion_offset, toolhead)}
	DEBUG_ECHO PREFIX="_BEACON_SET_NOZZLE_TEMP_OFFSET" MSG="toolhead: {toolhead}, coefficient: {expansion_coefficient|round(6)}, temp_delta: {temp_delta|round(1)},  expansion_offset: {expansion_offset|round(6)}"
	
	{% endif %}

[gcode_macro BEACON_MEASURE_BEACON_OFFSET]
variable_needs_compensation = False
variable_reference_z = 0.0
variable_front = 0.0
variable_front_left = 0.0
variable_front_right = 0.0
variable_back = 0.0
variable_back_left = 0.0
variable_back_right = 0.0
variable_right = 0.0
variable_left = 0.0
variable_margin_x = 40
variable_margin_y = 40
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=False
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Measure beacon offset..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="center"
	
	
	G0 X{margin_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_left"
	
	
	G0 X{safe_home_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front"
	
	
	G0 X{(printable_x_max - margin_x)} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_right"
	
	
	G0 X{safe_home_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back"
	
	
	G0 X{margin_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_left"
	
	
	G0 X{margin_x} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="left"
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_BEACON_ECHO_BEACON_OFFSET
	
	
	_LED_BEACON_CALIBRATION_END
	
	{% endif %}

[gcode_macro _BEACON_STORE_BEACON_OFFSET]
gcode = 
	
	{% set location = params.LOCATION|lower %}
	
	
	{% set last_z = printer.beacon.last_offset_result["delta"]|default(0)|float %}
	
	
	{% if location == "center" %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE={location} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_BEACON_OFFSET]
gcode = 
	
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float * 1000 %}
	{% set front_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_left|default(0)|float * 1000 %}
	{% set front = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front|default(0)|float * 1000 %}
	{% set front_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_right|default(0)|float * 1000 %}
	{% set right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].right|default(0)|float * 1000 %}
	{% set back_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_right|default(0)|float * 1000 %}
	{% set back = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back|default(0)|float * 1000 %}
	{% set back_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_left|default(0)|float * 1000 %}
	{% set left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].left|default(0)|float * 1000 %}
	
	{% set line_1 = "Front left:    %.6fμm" % (front_left) %}
	{% set line_2 = "Front center:  %.6fμm" % (front) %}
	{% set line_3 = "Front right:   %.6fμm" % (front_right) %}
	{% set line_4 = "Left center:   %.6fμm" % (left) %}
	{% set line_5 = "Right center:  %.6fμm" % (right) %}
	{% set line_6 = "Back left:     %.6fμm" % (back_left) %}
	{% set line_7 = "Back center:   %.6fμm" % (back) %}
	{% set line_8 = "Back right:    %.6fμm" % (back_right) %}
	
	{% set max_value = [(front_left|abs), (front|abs), (front_right|abs), (left|abs), (right|abs), (back_left|abs), (back|abs), (back_right|abs)]|max %}
	{% if max_value <= 50 %}
	{% set type = "success" %}
	{% set recommendation = "Very low beacon offset: %.6fμm._N_No beacon scan compensation needed." % max_value %}
	{% elif max_value > 50 and max_value <= 100 %}
	{% set type = "info" %}
	{% set recommendation = "Low beacon offset: %.6fμm._N_You may experience first layer inconsistensies, consider beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 100 and max_value <= 150 %}
	{% set type = "warning" %}
	{% set recommendation = "High beacon offset: %.6fμm._N_High chance of first layer problems, beacon scan compensation is highly encouraged." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 150 and max_value <= 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Very High beacon offset: %.6fμm._N_You will encounter first layer problems on large prints unless you activate beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Extremely high beacon offset: %.6fμm._N_You have significant scan/contact inconsistency which is indicative of mechanical problems, please investigate before resorting to software compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon offset relative to the center" TYPE={type} MSG={'"_N_%s_N__N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s"' % (recommendation, line_1, line_2, line_3, line_4, line_5, line_6, line_7, line_8)}

[gcode_macro BEACON_CREATE_SCAN_COMPENSATION_MESH]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set profile = params.PROFILE|default("auto")|string %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set keep_temp_meshes = params.KEEP_TEMP_MESHES|default(0) %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' %}
	{% set desired_spacing = printer["gcode_macro RatOS"].beacon_scan_compensation_desired_spacing|float %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	
	{% if not beacon_scan_compensation_enable %}
	RATOS_ECHO MSG="Beacon scan compensation is disabled!"
	
	{% else %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	
	
	RATOS_ECHO MSG="Please wait..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	G1 Z2.5 F{z_speed}
	{% if beacon_adaptive_heat_soak %}
	
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,9000]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if not (beacon_adaptive_heat_soak or bed_heat_soak_time > 0) %}
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if printer.z_tilt is defined %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% endif %}
	{% if printer.quad_gantry_level is defined %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% endif %}
	
	
	_BEACON_CREATE_SCAN_COMPENSATION_MESH_CORE PROFILE="{profile}" DESIRED_SPACING={desired_spacing} CHAMBER_TEMP={chamber_temp} KEEP_TEMP_MESHES={keep_temp_meshes}
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	{% if automated %}
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon scan compensation mesh created!"
	
	
	{% if not automated %}
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED]
gcode = 
	
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED" MSG="beacon_scan_compensation_profile {beacon_scan_compensation_profile}, beacon_scan_compensation_enable {beacon_scan_compensation_enable}"
	
	{% if beacon_scan_compensation_enable %}
	BEACON_APPLY_SCAN_COMPENSATION PROFILE="{beacon_scan_compensation_profile}"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL]
gcode = 
	
	{% set beacon_contact_start_print_true_zero = params.BEACON_CONTACT_START_PRINT_TRUE_ZERO|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = params.beacon_contact_calibrate_model_on_true_zero|lower == 'true' %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and not printer.beacon.model %}
	{% set beacon_model_required_for_true_zero = beacon_contact_start_print_true_zero and not beacon_contact_calibrate_model_on_true_zero %}
	{% set beacon_model_required_for_homing =
	printer.fastconfig.settings.stepper_z.endstop_pin == 'probe:z_virtual_endstop'
	and (( printer.fastconfig.settings.beacon.home_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower != 'true')
	or ( printer.fastconfig.settings.beacon.default_probe_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower != 'true' )) %}
	{% if beacon_model_required_for_homing or beacon_model_required_for_true_zero %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("An active Beacon model is required. Have you performed initial Beacon calibration?") }
	{% endif %}
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION]
gcode = 
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set bed_temp_mismatch_is_error = true if printer["gcode_macro RatOS"].beacon_scan_compensation_bed_temp_mismatch_is_error|default(false)|lower == 'true' else false %}
	
	{% set bed_temp = params.BED_TEMP|default(0)|float %}
	{% if bed_temp == 0 %}
	{% set bed_temp = printer.heater_bed.temperature %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_PREFLIGHT_CHECK_BEACON" MSG="beacon_scan_compensation_profile={beacon_scan_compensation_profile}, beacon_scan_compensation_enable={beacon_scan_compensation_enable}, bed_temp={bed_temp}"
	
	{% if beacon_scan_compensation_enable %}
	_VALIDATE_COMPENSATION_MESH_PROFILE PROFILE="{beacon_scan_compensation_profile}" TITLE="Check Beacon scan compensation profile" SUBJECT="Configured compensation profile '{beacon_scan_compensation_profile}'" COMPARE_BED_TEMP={bed_temp} COMPARE_BED_TEMP_IS_ERROR={bed_temp_mismatch_is_error}
	{% endif %}

[gcode_macro _BEACON_MAYBE_SCAN_COMPENSATION]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set needs_scan_compensation = true if printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].needs_compensation|default(false)|lower == 'true' else false %}
	
	{% if needs_scan_compensation %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% endif %}

[gcode_macro _BEACON_HOME_AND_ABL]
gcode = 
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	{% if needs_rehoming %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}

[gcode_macro SAVE_Z_OFFSET]
description = Deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead, or in Mainsail use the SAVE button in the Z-OFFSET section.
gcode = 
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default('false')|lower == 'true' %}
	{% set msg = "SAVE_Z_OFFSET is deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead,_N_or in Mainsail use the SAVE button in the Z-OFFSET section."%}
	{% if not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% set msg = msg + "_N_You must then use the SAVE_CONFIG command to persist the change." %}
	{% endif %}
	CONSOLE_ECHO TYPE="error" MSG="{msg}"

[gcode_macro _BEACON_OFFSET_COMPARE]
gcode = 
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing..."
	
	
	BEACON_OFFSET_COMPARE SAMPLES_DROP=1 SAMPLES=3
	BEACON_QUERY

[fan]
pin = rpi:gpio4

[fan_generic part_fan_t0]
pin = PA8
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[fan_generic part_fan_t1]
pin = PE5
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[heater_fan toolhead_cooling_fan_t0]
heater = extruder
shutdown_speed = 1
pin = toolboard_t0:PB4

[heater_fan toolhead_cooling_fan_t1]
heater = extruder1
shutdown_speed = 1
pin = toolboard_t1:PB4

[controller_fan controller_fan]
pin = dinghy:PA4
tachometer_pin = dinghy:PC15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[z_offset_probe]
pin = ^PG10
z_offset = -7
y_offset = 0
x_offset = 37.5
speed = 10
samples = 3
sample_retract_dist = 5
lift_speed = 10.0
samples_result = median
samples_tolerance = 0.2
samples_tolerance_retries = 5

[neopixel vaoc_led]
pin = PB10
chain_count = 6
color_order = GRB

[heater_fan vaoc_fan]
pin = PD13
heater = heater_bed
fan_speed = 1.0
heater_temp = 50

[fan_generic filter]
pin = !PD14
enable_pin = PD15

[gcode_macro T0]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = True
variable_color = "7bff33"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = -32.6
variable_parking_position = -57.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=0 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[gcode_macro T1]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = False
variable_color = "0ea5e9"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = 532.6
variable_parking_position = 557.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=1 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[save_variables]
filename = /home/pi/printer_data/config/ratos-variables.cfg

[mcu dinghy]
serial = /dev/serial/by-id/usb-Klipper_stm32f072xb_Dragon_dinghy-if00

[temperature_sensor th0]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA0

[temperature_sensor th1]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA1

[temperature_sensor th2]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA2

[temperature_sensor th3]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA3

[controller_fan CTL2]
pin = dinghy:PB14
tachometer_pin = dinghy:PB15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[mcu plasma]
serial = /dev/serial/by-id/usb-Klipper_rp2040_Plasma-if00

[neopixel Chamber_Lights]
pin = plasma:gpio15
chain_count = 140
color_order = GRBW
initial_red = 0.0
initial_green = 0.0
initial_blue = 0.0
initial_white = 0.1

[beacon model default]
model_coef = 1.5287863993594841,
	1.9289099639750602,
	0.8838828622507556,
	0.25554883784260735,
	-0.015171504024913506,
	0.3044946127013882,
	0.15820427856566457,
	-0.25262403959326246,
	0.042488512846660914,
	0.16662470122520964
model_domain = 1.842634574664148e-07,1.9339206373083917e-07
model_range = 0.200000,5.000000
model_temp = 13.222247
model_offset = 0.00000

[bed_mesh default]
version = 1
points = 
	0.016163, 0.016713, 0.001923, -0.017658, -0.031574, -0.032498, -0.030898, -0.032177, -0.035213, -0.031148, -0.021322, -0.016924, -0.015012, -0.013911, -0.012197, -0.012583, -0.010489, -0.007529, -0.003986, -0.000980, 0.005518, 0.014442, 0.027426, 0.034677, 0.037410, 0.040391, 0.041842, 0.040369, 0.037615, 0.030776, 0.027664, 0.022856, 0.016892, 0.015398, 0.014717, 0.006921, 0.001532, 0.000731, 0.008657, 0.014036
	0.005356, -0.005066, -0.016998, -0.029668, -0.038334, -0.043672, -0.041139, -0.042488, -0.045199, -0.039432, -0.028746, -0.023642, -0.024058, -0.022802, -0.019679, -0.018514, -0.018102, -0.016476, -0.012722, -0.010077, -0.001809, 0.007180, 0.019853, 0.027754, 0.029964, 0.033626, 0.036783, 0.032018, 0.029372, 0.020847, 0.017634, 0.011926, 0.009013, 0.009254, 0.007972, -0.001380, -0.006940, -0.002160, 0.006135, 0.008330
	-0.004900, -0.006720, -0.021914, -0.039691, -0.050459, -0.050377, -0.046281, -0.048755, -0.054708, -0.051499, -0.033927, -0.027632, -0.030243, -0.031447, -0.024387, -0.021408, -0.020382, -0.018068, -0.015930, -0.013877, -0.006099, 0.003479, 0.013310, 0.024783, 0.025522, 0.030849, 0.033573, 0.031409, 0.025495, 0.016683, 0.011264, 0.008805, 0.006856, 0.008059, 0.007305, 0.002581, -0.003320, -0.003239, 0.004691, 0.010045
	-0.008791, -0.019334, -0.029149, -0.040533, -0.051698, -0.058235, -0.054863, -0.054840, -0.055692, -0.049534, -0.036731, -0.033053, -0.035667, -0.035315, -0.024352, -0.023825, -0.022538, -0.020438, -0.018207, -0.015389, -0.006515, 0.001966, 0.013591, 0.019434, 0.020600, 0.024967, 0.029425, 0.026812, 0.018980, 0.007878, 0.002360, 0.000859, 0.003849, 0.005649, 0.005421, -0.000416, -0.007906, -0.003164, 0.007582, 0.010039
	-0.018512, -0.018210, -0.033932, -0.050501, -0.061588, -0.064139, -0.060236, -0.062528, -0.067065, -0.062039, -0.045815, -0.039448, -0.040521, -0.042080, -0.033870, -0.030878, -0.027396, -0.024548, -0.021298, -0.020041, -0.011880, -0.002847, 0.008689, 0.015857, 0.015934, 0.018697, 0.022439, 0.022106, 0.017916, 0.005879, 0.001037, -0.001311, -0.001335, 0.001897, 0.003656, 0.000561, -0.006084, -0.005683, 0.000338, 0.006245
	-0.028558, -0.036721, -0.044680, -0.054969, -0.066140, -0.075045, -0.073515, -0.073161, -0.075696, -0.068963, -0.058892, -0.053111, -0.050990, -0.048040, -0.041262, -0.037419, -0.034866, -0.031845, -0.029787, -0.026524, -0.017896, -0.009322, -0.001010, 0.005819, 0.008058, 0.010456, 0.013266, 0.012529, 0.007992, -0.001491, -0.006769, -0.009303, -0.005980, -0.003567, -0.003340, -0.011496, -0.018818, -0.014808, -0.004181, -0.000733
	-0.037253, -0.038393, -0.053129, -0.066170, -0.075959, -0.079233, -0.077475, -0.082688, -0.086779, -0.083983, -0.069005, -0.062542, -0.060351, -0.058481, -0.051101, -0.043149, -0.039837, -0.037039, -0.034698, -0.031301, -0.024330, -0.019786, -0.010285, -0.001967, 0.002812, 0.004899, 0.009657, 0.006946, 0.002155, -0.005232, -0.009851, -0.011218, -0.011509, -0.010097, -0.010293, -0.013175, -0.018958, -0.019846, -0.012107, -0.005641
	-0.046584, -0.055590, -0.062606, -0.069218, -0.080399, -0.087414, -0.089037, -0.092376, -0.095115, -0.088957, -0.080802, -0.073290, -0.068741, -0.064591, -0.054452, -0.048270, -0.045916, -0.044559, -0.042047, -0.039605, -0.032667, -0.025789, -0.019495, -0.012773, -0.006697, -0.003025, 0.001413, 0.000817, -0.004738, -0.013008, -0.017605, -0.018191, -0.018524, -0.016356, -0.016750, -0.021992, -0.028943, -0.025791, -0.016146, -0.010447
	-0.051029, -0.051677, -0.068218, -0.079622, -0.088590, -0.089331, -0.089731, -0.096072, -0.105329, -0.100771, -0.087584, -0.079320, -0.075489, -0.072081, -0.064183, -0.054662, -0.048601, -0.049465, -0.047050, -0.045011, -0.040009, -0.032508, -0.025212, -0.018144, -0.011996, -0.008136, -0.003187, -0.003214, -0.006646, -0.013044, -0.019446, -0.020615, -0.022270, -0.021298, -0.020215, -0.020946, -0.026034, -0.026598, -0.021025, -0.012328
	-0.057184, -0.064908, -0.073093, -0.081584, -0.091971, -0.097048, -0.097688, -0.101869, -0.106651, -0.102162, -0.095658, -0.087938, -0.082718, -0.077017, -0.069608, -0.060682, -0.056889, -0.056864, -0.054260, -0.052011, -0.044563, -0.038927, -0.031943, -0.025832, -0.021170, -0.014319, -0.009046, -0.008543, -0.011751, -0.020287, -0.026608, -0.027259, -0.029120, -0.025549, -0.023221, -0.027725, -0.032477, -0.028427, -0.019343, -0.014932
	-0.060411, -0.062241, -0.080781, -0.090744, -0.100903, -0.099702, -0.098468, -0.104236, -0.116853, -0.112701, -0.102623, -0.095036, -0.091407, -0.089871, -0.079701, -0.070222, -0.064325, -0.063875, -0.062248, -0.059396, -0.052699, -0.047589, -0.041526, -0.028442, -0.024526, -0.019549, -0.015403, -0.014251, -0.017989, -0.022824, -0.027328, -0.029155, -0.033315, -0.032426, -0.027619, -0.030776, -0.033688, -0.032458, -0.027219, -0.019649
	-0.067541, -0.076514, -0.082321, -0.088656, -0.099968, -0.104930, -0.105875, -0.109051, -0.115531, -0.112996, -0.105760, -0.100390, -0.096171, -0.090011, -0.080050, -0.073632, -0.067451, -0.067031, -0.065225, -0.062471, -0.056370, -0.050129, -0.041626, -0.030801, -0.027579, -0.022472, -0.014826, -0.015306, -0.020316, -0.025953, -0.030661, -0.034103, -0.035502, -0.032738, -0.031311, -0.037314, -0.041306, -0.035280, -0.027449, -0.020395
	-0.068162, -0.069269, -0.088235, -0.096809, -0.103385, -0.103271, -0.102507, -0.109535, -0.123412, -0.118580, -0.106622, -0.099580, -0.097644, -0.096978, -0.087259, -0.077196, -0.068978, -0.067016, -0.063682, -0.062548, -0.057901, -0.052295, -0.044088, -0.032703, -0.026551, -0.021607, -0.014155, -0.013747, -0.017390, -0.022419, -0.027444, -0.030877, -0.033450, -0.032423, -0.032041, -0.033598, -0.035149, -0.034054, -0.029356, -0.020998
	-0.069473, -0.075924, -0.083569, -0.089648, -0.101235, -0.105828, -0.109144, -0.112613, -0.117233, -0.114186, -0.107090, -0.098616, -0.097084, -0.094257, -0.086773, -0.076409, -0.069532, -0.066472, -0.060956, -0.059191, -0.052886, -0.047752, -0.041275, -0.032437, -0.027780, -0.020398, -0.012061, -0.010133, -0.014056, -0.021528, -0.027924, -0.030605, -0.030609, -0.026068, -0.029346, -0.033991, -0.038254, -0.030610, -0.021109, -0.015885
	-0.068084, -0.066409, -0.083944, -0.094013, -0.102504, -0.105274, -0.106036, -0.112090, -0.121664, -0.117824, -0.104850, -0.097467, -0.098833, -0.098622, -0.089603, -0.078147, -0.068143, -0.066300, -0.061573, -0.057727, -0.054825, -0.048625, -0.040164, -0.030532, -0.025948, -0.020264, -0.014196, -0.010702, -0.013794, -0.019775, -0.026095, -0.028838, -0.030254, -0.027944, -0.027980, -0.030915, -0.032446, -0.028861, -0.023732, -0.014676
	-0.065280, -0.068669, -0.076948, -0.082397, -0.094986, -0.105117, -0.107099, -0.108954, -0.112557, -0.110326, -0.100725, -0.096325, -0.096240, -0.092388, -0.081185, -0.071682, -0.065650, -0.062250, -0.057027, -0.054691, -0.048349, -0.042069, -0.032712, -0.027728, -0.023396, -0.018458, -0.008357, -0.005699, -0.011447, -0.020033, -0.026387, -0.030280, -0.028443, -0.023735, -0.023838, -0.031580, -0.034204, -0.027768, -0.018029, -0.010628
	-0.061662, -0.057052, -0.075163, -0.086710, -0.094182, -0.097544, -0.098814, -0.105908, -0.114460, -0.111718, -0.097559, -0.091614, -0.093860, -0.093098, -0.081687, -0.069410, -0.064117, -0.062745, -0.055603, -0.051413, -0.048043, -0.040363, -0.031842, -0.023420, -0.017470, -0.012600, -0.008163, -0.003898, -0.007635, -0.013254, -0.019807, -0.025153, -0.027074, -0.023513, -0.023727, -0.028669, -0.029153, -0.024831, -0.018735, -0.009246
	-0.056176, -0.059439, -0.066501, -0.071527, -0.085216, -0.094918, -0.097595, -0.099419, -0.101847, -0.102015, -0.093849, -0.089867, -0.088840, -0.083167, -0.071832, -0.062522, -0.058023, -0.057771, -0.053050, -0.048285, -0.041374, -0.033527, -0.024473, -0.018428, -0.013958, -0.008161, -0.001196, 0.001754, -0.004016, -0.011132, -0.018325, -0.021813, -0.021514, -0.016948, -0.018061, -0.025702, -0.028671, -0.021470, -0.011028, -0.001934
	-0.059202, -0.050525, -0.065461, -0.076792, -0.084156, -0.088538, -0.090719, -0.096070, -0.105729, -0.105136, -0.090350, -0.083865, -0.087807, -0.086145, -0.074773, -0.064235, -0.057641, -0.055896, -0.051286, -0.046566, -0.042431, -0.034723, -0.023762, -0.014983, -0.009126, -0.004877, 0.000094, 0.003492, -0.000931, -0.005883, -0.011665, -0.015251, -0.016432, -0.016119, -0.015373, -0.018827, -0.019994, -0.017564, -0.012298, 0.002094
	-0.055561, -0.058184, -0.062669, -0.068111, -0.080741, -0.091895, -0.093911, -0.094387, -0.100239, -0.100695, -0.089841, -0.085682, -0.085212, -0.082910, -0.073072, -0.063594, -0.056157, -0.053482, -0.048107, -0.045405, -0.039982, -0.029777, -0.019905, -0.013872, -0.009732, -0.004272, 0.003500, 0.006909, 0.001302, -0.004626, -0.012374, -0.014751, -0.014637, -0.011794, -0.012913, -0.018244, -0.023377, -0.018086, -0.006575, 0.003294
	-0.062834, -0.047300, -0.060870, -0.073023, -0.079303, -0.082121, -0.083623, -0.091321, -0.100996, -0.098896, -0.085406, -0.078881, -0.081932, -0.082077, -0.074409, -0.063158, -0.053822, -0.050328, -0.045077, -0.039678, -0.035825, -0.028532, -0.017793, -0.009121, -0.003444, -0.000905, 0.003990, 0.007745, 0.004595, 0.000143, -0.004555, -0.007411, -0.010850, -0.010100, -0.010079, -0.013177, -0.016434, -0.014663, -0.010248, -0.000213
	-0.054748, -0.053907, -0.057576, -0.063118, -0.072478, -0.081366, -0.084424, -0.086348, -0.089718, -0.089305, -0.081771, -0.076889, -0.076923, -0.073518, -0.067973, -0.057643, -0.050848, -0.046966, -0.041560, -0.036436, -0.029233, -0.020685, -0.010240, -0.004935, -0.001084, 0.002478, 0.009168, 0.014038, 0.010885, 0.004752, -0.001650, -0.004209, -0.003998, -0.002336, -0.003784, -0.010930, -0.016480, -0.012798, -0.003650, 0.002998
	-0.059345, -0.041989, -0.057435, -0.068229, -0.072857, -0.072586, -0.075155, -0.083286, -0.091292, -0.089727, -0.073702, -0.068353, -0.072910, -0.073863, -0.065527, -0.053635, -0.046064, -0.043899, -0.037607, -0.031251, -0.026194, -0.018885, -0.008095, 0.000309, 0.004911, 0.007046, 0.010642, 0.015635, 0.015277, 0.012612, 0.008074, 0.004852, 0.001546, 0.000504, 0.000589, -0.002769, -0.006432, -0.007765, -0.005391, 0.006950
	-0.050324, -0.049088, -0.052417, -0.057257, -0.063818, -0.071057, -0.074636, -0.075459, -0.079445, -0.077368, -0.068788, -0.063940, -0.065040, -0.063419, -0.054864, -0.044910, -0.038774, -0.036951, -0.031149, -0.026080, -0.018383, -0.011985, -0.001732, 0.003893, 0.007180, 0.011120, 0.017429, 0.021738, 0.019167, 0.015812, 0.011027, 0.007243, 0.006720, 0.009346, 0.006598, -0.003776, -0.009199, -0.007592, 0.005481, 0.014396
	-0.058437, -0.035937, -0.050762, -0.060425, -0.061123, -0.059090, -0.062399, -0.072124, -0.080338, -0.074950, -0.060985, -0.054754, -0.059333, -0.060500, -0.051714, -0.038834, -0.031117, -0.031693, -0.025186, -0.017982, -0.014316, -0.010137, 0.000228, 0.008774, 0.014018, 0.016470, 0.019918, 0.022071, 0.021109, 0.019957, 0.018698, 0.015803, 0.013135, 0.011136, 0.008719, 0.003522, -0.000994, 0.000525, 0.006297, 0.018454
	-0.046143, -0.041577, -0.045391, -0.046668, -0.051722, -0.057607, -0.062802, -0.065205, -0.068243, -0.066293, -0.058216, -0.051324, -0.051806, -0.051018, -0.043393, -0.032431, -0.024016, -0.023321, -0.018504, -0.013897, -0.008455, -0.001123, 0.006609, 0.010462, 0.013887, 0.019328, 0.024804, 0.026590, 0.023420, 0.020337, 0.017129, 0.017199, 0.016391, 0.015616, 0.013257, 0.005832, -0.000019, 0.003462, 0.014308, 0.023624
	-0.051989, -0.030294, -0.043380, -0.051339, -0.050711, -0.048193, -0.052258, -0.061218, -0.070507, -0.068810, -0.049476, -0.042352, -0.046018, -0.046673, -0.038670, -0.027263, -0.018137, -0.018587, -0.013603, -0.008482, -0.004647, -0.000011, 0.008230, 0.015652, 0.019436, 0.023069, 0.024762, 0.027750, 0.028115, 0.026227, 0.022220, 0.023166, 0.020341, 0.018455, 0.014918, 0.011932, 0.007138, 0.008523, 0.014718, 0.026201
	-0.041448, -0.035286, -0.036538, -0.037577, -0.044652, -0.049300, -0.051092, -0.052841, -0.058068, -0.056947, -0.046235, -0.038436, -0.037494, -0.034175, -0.028932, -0.016904, -0.010075, -0.010552, -0.004464, -0.001243, 0.003236, 0.010200, 0.015604, 0.020362, 0.023157, 0.028023, 0.032826, 0.035958, 0.034819, 0.030600, 0.025988, 0.026013, 0.026284, 0.025661, 0.022322, 0.013336, 0.006464, 0.011312, 0.022330, 0.031668
	-0.048540, -0.022534, -0.035260, -0.042156, -0.042749, -0.037408, -0.038818, -0.047322, -0.056808, -0.053643, -0.035691, -0.027822, -0.028789, -0.028255, -0.020274, -0.007285, -0.000723, -0.000788, 0.005440, 0.008938, 0.008953, 0.012074, 0.017957, 0.025241, 0.029175, 0.032057, 0.033733, 0.038359, 0.039349, 0.037161, 0.034052, 0.034585, 0.032020, 0.029940, 0.026326, 0.024577, 0.020432, 0.021586, 0.024568, 0.034552
	-0.033086, -0.027982, -0.029443, -0.029011, -0.035629, -0.040579, -0.038290, -0.037389, -0.041260, -0.040430, -0.032279, -0.021394, -0.018817, -0.015525, -0.007558, 0.006345, 0.011048, 0.011271, 0.013497, 0.017030, 0.017449, 0.022752, 0.026764, 0.030722, 0.033532, 0.037203, 0.043356, 0.048536, 0.047776, 0.043851, 0.039311, 0.039944, 0.039954, 0.038931, 0.034893, 0.030946, 0.023127, 0.027359, 0.034859, 0.043920
	-0.036218, -0.016846, -0.030897, -0.036980, -0.037261, -0.033334, -0.030888, -0.034074, -0.042142, -0.039980, -0.021377, -0.013603, -0.014171, -0.013131, -0.001768, 0.014998, 0.020060, 0.018173, 0.019934, 0.024704, 0.023739, 0.024617, 0.027288, 0.035116, 0.041187, 0.043128, 0.045921, 0.051709, 0.053031, 0.050698, 0.047697, 0.047728, 0.046845, 0.043201, 0.041805, 0.040728, 0.036184, 0.034435, 0.035120, 0.045329
	-0.029808, -0.023871, -0.026541, -0.026705, -0.031203, -0.036908, -0.034411, -0.029231, -0.028090, -0.026102, -0.016691, -0.007747, -0.004471, 0.001560, 0.010738, 0.025062, 0.027672, 0.024833, 0.026976, 0.029502, 0.030754, 0.035709, 0.039403, 0.044719, 0.046379, 0.049250, 0.054178, 0.059793, 0.059542, 0.052111, 0.047608, 0.050103, 0.053142, 0.052747, 0.050045, 0.044102, 0.033149, 0.035392, 0.045678, 0.054080
	-0.032238, -0.008993, -0.023999, -0.030969, -0.028658, -0.024887, -0.024493, -0.028088, -0.031053, -0.022849, -0.003868, 0.004647, 0.004540, 0.007560, 0.018373, 0.031401, 0.035778, 0.033768, 0.035173, 0.035884, 0.036597, 0.038940, 0.044566, 0.053914, 0.056554, 0.056382, 0.056449, 0.060387, 0.062696, 0.058223, 0.055016, 0.056193, 0.056891, 0.052793, 0.052741, 0.052626, 0.048117, 0.045032, 0.048033, 0.055100
	-0.019758, -0.015110, -0.017814, -0.018871, -0.023340, -0.028653, -0.026880, -0.018681, -0.017020, -0.011343, -0.001002, 0.008249, 0.014012, 0.020367, 0.026878, 0.038534, 0.041827, 0.039532, 0.039775, 0.039109, 0.043172, 0.049325, 0.056604, 0.059583, 0.059329, 0.059876, 0.062766, 0.068759, 0.067214, 0.059657, 0.055950, 0.056798, 0.058619, 0.058591, 0.059849, 0.056473, 0.046841, 0.047921, 0.058342, 0.065346
	-0.018628, -0.000296, -0.014764, -0.022634, -0.020483, -0.016362, -0.015485, -0.017352, -0.020246, -0.010362, 0.008635, 0.018414, 0.018542, 0.024258, 0.033370, 0.045728, 0.049983, 0.044610, 0.044638, 0.047649, 0.049220, 0.051954, 0.058932, 0.065915, 0.069102, 0.067410, 0.067680, 0.073734, 0.072203, 0.067293, 0.063945, 0.064378, 0.065047, 0.061989, 0.062882, 0.063468, 0.059707, 0.057986, 0.059739, 0.066139
	-0.010091, -0.006551, -0.008018, -0.009589, -0.016068, -0.020662, -0.019451, -0.010985, -0.009391, -0.003580, 0.007826, 0.019598, 0.024961, 0.033762, 0.040618, 0.050868, 0.052139, 0.050495, 0.049198, 0.051777, 0.056840, 0.061771, 0.068414, 0.072295, 0.073443, 0.072145, 0.073414, 0.079338, 0.075988, 0.067367, 0.064745, 0.064435, 0.066982, 0.065811, 0.067424, 0.063230, 0.058438, 0.059982, 0.067672, 0.072460
	-0.016254, 0.006291, -0.008031, -0.013944, -0.014475, -0.010741, -0.009932, -0.011709, -0.015503, -0.006971, 0.013190, 0.024865, 0.029121, 0.033942, 0.044335, 0.054572, 0.058078, 0.055224, 0.055897, 0.058327, 0.061207, 0.063939, 0.070506, 0.078141, 0.084203, 0.081223, 0.079519, 0.082883, 0.080890, 0.076174, 0.071279, 0.073064, 0.071225, 0.066859, 0.069860, 0.070836, 0.069427, 0.069140, 0.070950, 0.075269
	-0.008127, 0.000730, 0.001164, -0.000308, -0.006659, -0.012343, -0.011463, -0.003755, -0.001876, 0.005166, 0.016616, 0.030243, 0.036509, 0.045020, 0.053681, 0.063738, 0.066425, 0.063964, 0.062796, 0.065633, 0.071912, 0.077280, 0.082580, 0.086477, 0.089798, 0.089603, 0.091453, 0.096125, 0.088708, 0.079903, 0.074317, 0.076190, 0.075399, 0.075242, 0.079628, 0.077855, 0.071473, 0.073702, 0.082757, 0.088086
	-0.010951, 0.013218, -0.000878, -0.006241, -0.005623, 0.000046, 0.000158, -0.002943, -0.005314, 0.005491, 0.026890, 0.035754, 0.041490, 0.045829, 0.059325, 0.070249, 0.074114, 0.071815, 0.073229, 0.076313, 0.080778, 0.081554, 0.087919, 0.096206, 0.101562, 0.101674, 0.100494, 0.103989, 0.100292, 0.093977, 0.088080, 0.088136, 0.086555, 0.081494, 0.084966, 0.087073, 0.084113, 0.085184, 0.087700, 0.092188
	-0.002972, 0.006020, 0.006098, 0.004303, 0.001326, -0.002386, -0.001840, 0.005325, 0.008624, 0.016246, 0.026781, 0.039696, 0.048540, 0.055938, 0.066982, 0.076497, 0.080828, 0.079669, 0.080127, 0.083754, 0.089783, 0.093456, 0.100570, 0.105322, 0.107132, 0.110571, 0.113141, 0.118064, 0.111721, 0.101634, 0.093555, 0.093112, 0.093104, 0.092325, 0.094780, 0.092552, 0.085283, 0.088882, 0.097508, 0.105280
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 11.4
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Preperations]
version = 1
points = 
	0.012158, -0.006098, -0.020628, -0.034069, -0.049418, -0.058491, -0.062706, -0.063181, -0.065552, -0.063461, -0.057373, -0.056717, -0.056579, -0.054080, -0.053373, -0.056878, -0.057281, -0.055224, -0.049676, -0.047605, -0.041454, -0.034605, -0.022490, -0.011292, -0.009411, -0.005344, -0.003510, -0.002717, -0.005999, -0.010712, -0.013141, -0.015611, -0.020004, -0.017667, -0.016629, -0.022248, -0.024864, -0.024065, -0.014921, -0.010826
	-0.005958, -0.021084, -0.033800, -0.047903, -0.059950, -0.071345, -0.072502, -0.073350, -0.075852, -0.072963, -0.067236, -0.064315, -0.065698, -0.064338, -0.062871, -0.065238, -0.067095, -0.063584, -0.059241, -0.057846, -0.051380, -0.043157, -0.030230, -0.019950, -0.018121, -0.014291, -0.009354, -0.013065, -0.016464, -0.022925, -0.025337, -0.026541, -0.030577, -0.029068, -0.027094, -0.030532, -0.034241, -0.032625, -0.021498, -0.020513
	-0.017526, -0.027763, -0.040710, -0.055305, -0.068172, -0.079641, -0.081247, -0.081903, -0.083679, -0.081855, -0.073270, -0.070340, -0.072083, -0.071536, -0.066055, -0.065901, -0.069085, -0.066531, -0.063284, -0.061616, -0.053366, -0.047292, -0.035451, -0.023167, -0.022205, -0.016699, -0.012552, -0.014153, -0.018802, -0.030443, -0.032210, -0.034051, -0.034437, -0.031439, -0.030406, -0.032817, -0.036351, -0.034849, -0.024250, -0.019489
	-0.017750, -0.030284, -0.043463, -0.055839, -0.071865, -0.084888, -0.086157, -0.084619, -0.086681, -0.084515, -0.075246, -0.073263, -0.075604, -0.075123, -0.069177, -0.070723, -0.071097, -0.068644, -0.065465, -0.063718, -0.057574, -0.049335, -0.036556, -0.028418, -0.028259, -0.023387, -0.018454, -0.020519, -0.027499, -0.038314, -0.041534, -0.041886, -0.039972, -0.036438, -0.033959, -0.033009, -0.038291, -0.036339, -0.022688, -0.024783
	-0.021354, -0.034103, -0.047541, -0.060551, -0.075691, -0.089373, -0.092241, -0.091621, -0.093203, -0.090723, -0.082480, -0.079781, -0.079706, -0.079674, -0.074365, -0.073780, -0.073465, -0.070165, -0.064970, -0.065503, -0.059104, -0.051038, -0.041817, -0.031243, -0.031386, -0.028837, -0.023658, -0.024237, -0.029641, -0.039210, -0.042766, -0.044461, -0.041863, -0.039075, -0.034881, -0.034571, -0.039386, -0.038253, -0.031659, -0.024202
	-0.027696, -0.041184, -0.054054, -0.064759, -0.080898, -0.094964, -0.097906, -0.098033, -0.101256, -0.098300, -0.091517, -0.088420, -0.086945, -0.085220, -0.079938, -0.079979, -0.079828, -0.074842, -0.072903, -0.072415, -0.065384, -0.057454, -0.048482, -0.040977, -0.039336, -0.036065, -0.032553, -0.034336, -0.039337, -0.046271, -0.049398, -0.051220, -0.049530, -0.045000, -0.045029, -0.042100, -0.049767, -0.046386, -0.035574, -0.032188
	-0.033426, -0.046259, -0.059363, -0.068024, -0.084858, -0.097009, -0.103434, -0.106215, -0.107319, -0.106178, -0.100333, -0.097536, -0.095352, -0.091322, -0.086332, -0.082309, -0.081440, -0.078413, -0.075067, -0.073134, -0.068255, -0.062667, -0.054300, -0.046004, -0.042001, -0.039181, -0.035010, -0.036092, -0.041599, -0.048788, -0.051751, -0.051179, -0.051019, -0.049121, -0.045860, -0.046756, -0.050005, -0.051613, -0.040237, -0.035349
	-0.037931, -0.051993, -0.066455, -0.075044, -0.088177, -0.102890, -0.108223, -0.112373, -0.115787, -0.113421, -0.108543, -0.105936, -0.101048, -0.096863, -0.090726, -0.087882, -0.086665, -0.083874, -0.081096, -0.080894, -0.075125, -0.071038, -0.063072, -0.054696, -0.051039, -0.046728, -0.042566, -0.043887, -0.048745, -0.056834, -0.059808, -0.060521, -0.060664, -0.057968, -0.056317, -0.052477, -0.058814, -0.055877, -0.046325, -0.042545
	-0.041429, -0.053634, -0.067633, -0.077111, -0.090998, -0.103561, -0.109445, -0.114741, -0.120075, -0.119821, -0.114703, -0.110411, -0.105589, -0.099826, -0.093730, -0.089705, -0.087199, -0.086439, -0.082688, -0.082221, -0.078348, -0.073203, -0.065273, -0.058731, -0.054025, -0.049231, -0.044830, -0.043830, -0.045839, -0.054137, -0.059075, -0.059515, -0.058546, -0.056956, -0.054145, -0.053129, -0.056587, -0.056341, -0.047057, -0.039936
	-0.044295, -0.058972, -0.072101, -0.082726, -0.095001, -0.106449, -0.111505, -0.118363, -0.124608, -0.123506, -0.120263, -0.115400, -0.110227, -0.104535, -0.100348, -0.095757, -0.092961, -0.092377, -0.089613, -0.088047, -0.084834, -0.079314, -0.072500, -0.064519, -0.060449, -0.055767, -0.051803, -0.050997, -0.052855, -0.058115, -0.063348, -0.065363, -0.067936, -0.063474, -0.061475, -0.054726, -0.062529, -0.055352, -0.048878, -0.044991
	-0.045804, -0.056574, -0.073308, -0.082450, -0.097495, -0.107467, -0.111501, -0.116418, -0.126724, -0.125980, -0.123231, -0.120494, -0.114667, -0.111289, -0.103451, -0.099228, -0.095880, -0.095882, -0.093328, -0.091000, -0.087051, -0.081909, -0.075949, -0.064971, -0.061050, -0.055137, -0.049046, -0.047319, -0.049806, -0.056968, -0.059608, -0.060249, -0.063032, -0.060556, -0.056284, -0.056263, -0.058891, -0.057890, -0.051554, -0.042382
	-0.049818, -0.062681, -0.076305, -0.084328, -0.098717, -0.107866, -0.113937, -0.120088, -0.128622, -0.128931, -0.126353, -0.123191, -0.118529, -0.115642, -0.106288, -0.103976, -0.099708, -0.097750, -0.094501, -0.094545, -0.090910, -0.085952, -0.077352, -0.067196, -0.062435, -0.057738, -0.052934, -0.051098, -0.055294, -0.061112, -0.063120, -0.067525, -0.067979, -0.066558, -0.064608, -0.060597, -0.067812, -0.057641, -0.056224, -0.046471
	-0.050591, -0.060432, -0.075602, -0.083877, -0.096933, -0.106147, -0.112334, -0.118295, -0.127966, -0.128757, -0.125157, -0.121831, -0.118557, -0.116124, -0.108723, -0.104502, -0.099469, -0.095841, -0.090662, -0.089822, -0.087969, -0.084545, -0.076375, -0.064821, -0.059093, -0.053427, -0.047372, -0.044341, -0.047964, -0.054064, -0.057133, -0.059152, -0.061568, -0.059109, -0.056640, -0.056691, -0.056844, -0.054564, -0.048514, -0.040641
	-0.047704, -0.059564, -0.073127, -0.080945, -0.093764, -0.105483, -0.111501, -0.118792, -0.124812, -0.126576, -0.122064, -0.118087, -0.116126, -0.114867, -0.108053, -0.103336, -0.097558, -0.093250, -0.086537, -0.085303, -0.083677, -0.079292, -0.070542, -0.062526, -0.056818, -0.052534, -0.044035, -0.041353, -0.046942, -0.051329, -0.055481, -0.062777, -0.058499, -0.058025, -0.057390, -0.053562, -0.060843, -0.046555, -0.046260, -0.036083
	-0.046496, -0.052983, -0.067518, -0.076904, -0.091704, -0.103105, -0.111995, -0.117751, -0.122307, -0.122941, -0.118230, -0.115004, -0.114258, -0.113138, -0.105515, -0.098417, -0.093384, -0.090070, -0.083281, -0.079846, -0.078725, -0.075452, -0.066225, -0.057269, -0.053103, -0.047808, -0.039772, -0.036834, -0.041270, -0.047376, -0.051111, -0.053848, -0.053029, -0.050301, -0.048919, -0.050775, -0.050121, -0.046842, -0.039633, -0.030497
	-0.040695, -0.051685, -0.064038, -0.070974, -0.086679, -0.101773, -0.109889, -0.114373, -0.117883, -0.118764, -0.113125, -0.110931, -0.111099, -0.109664, -0.098733, -0.093182, -0.090154, -0.086213, -0.077214, -0.077108, -0.075555, -0.069117, -0.060704, -0.054093, -0.049253, -0.044799, -0.037536, -0.035304, -0.040134, -0.045456, -0.051720, -0.056675, -0.053743, -0.052923, -0.049701, -0.050238, -0.056776, -0.041485, -0.041755, -0.027329
	-0.039842, -0.039428, -0.055732, -0.063890, -0.079179, -0.092823, -0.101698, -0.106156, -0.111709, -0.113152, -0.108033, -0.104872, -0.105645, -0.103501, -0.094487, -0.087264, -0.084273, -0.080950, -0.074116, -0.070973, -0.068409, -0.062825, -0.054757, -0.044150, -0.040620, -0.036602, -0.031538, -0.026478, -0.031123, -0.037600, -0.042341, -0.046700, -0.047380, -0.042880, -0.040967, -0.045367, -0.044192, -0.038553, -0.029948, -0.020790
	-0.030596, -0.038279, -0.051528, -0.058981, -0.073983, -0.089044, -0.099173, -0.101740, -0.104830, -0.107083, -0.102306, -0.101554, -0.101336, -0.097146, -0.089217, -0.083800, -0.080621, -0.078071, -0.071535, -0.068328, -0.065806, -0.056882, -0.048683, -0.039756, -0.036349, -0.031328, -0.025351, -0.024133, -0.029773, -0.033858, -0.040011, -0.044146, -0.043900, -0.044797, -0.038019, -0.042319, -0.047297, -0.031851, -0.034318, -0.013527
	-0.032121, -0.034722, -0.047839, -0.054710, -0.069175, -0.084213, -0.094533, -0.097233, -0.100863, -0.104775, -0.099781, -0.097416, -0.098804, -0.096059, -0.086694, -0.079692, -0.076749, -0.074609, -0.068106, -0.063906, -0.061136, -0.055447, -0.045559, -0.035389, -0.029696, -0.025708, -0.020034, -0.017335, -0.022665, -0.028532, -0.032369, -0.035760, -0.037212, -0.035201, -0.032872, -0.034132, -0.035907, -0.032127, -0.025026, -0.009282
	-0.026707, -0.034374, -0.045183, -0.052691, -0.067014, -0.084964, -0.092286, -0.094441, -0.099291, -0.103609, -0.098278, -0.094972, -0.097169, -0.095394, -0.086653, -0.080205, -0.076284, -0.070594, -0.064535, -0.062012, -0.060174, -0.051216, -0.040622, -0.033396, -0.029636, -0.024235, -0.017274, -0.018232, -0.021459, -0.024778, -0.031754, -0.034481, -0.033398, -0.037949, -0.030432, -0.033219, -0.038432, -0.021975, -0.030052, -0.009295
	-0.028559, -0.029280, -0.042071, -0.048655, -0.061603, -0.076257, -0.086817, -0.091815, -0.095682, -0.098682, -0.093729, -0.091168, -0.092213, -0.090073, -0.084070, -0.077048, -0.072045, -0.066267, -0.060309, -0.053639, -0.051696, -0.046852, -0.034069, -0.025602, -0.020640, -0.018021, -0.013180, -0.009049, -0.013846, -0.018012, -0.021061, -0.024515, -0.027068, -0.026804, -0.024283, -0.025595, -0.028234, -0.025272, -0.019246, -0.008595
	-0.025711, -0.029003, -0.038836, -0.048015, -0.058511, -0.074480, -0.083738, -0.087945, -0.091439, -0.094310, -0.090288, -0.087858, -0.088589, -0.086163, -0.081829, -0.075146, -0.071136, -0.064399, -0.057338, -0.052103, -0.049650, -0.043210, -0.032998, -0.023124, -0.020191, -0.016625, -0.012433, -0.010465, -0.009871, -0.015007, -0.021217, -0.021582, -0.023800, -0.027652, -0.021527, -0.027137, -0.030828, -0.020152, -0.026202, -0.008568
	-0.031287, -0.022523, -0.035800, -0.041583, -0.052691, -0.065901, -0.075941, -0.079246, -0.083936, -0.086778, -0.082235, -0.078893, -0.080642, -0.079419, -0.074324, -0.067418, -0.062113, -0.057744, -0.049923, -0.043390, -0.040055, -0.035512, -0.023838, -0.015485, -0.009895, -0.008346, -0.005387, 0.001467, -0.000104, -0.003777, -0.007926, -0.012023, -0.013970, -0.014207, -0.013994, -0.017009, -0.019233, -0.019282, -0.014210, -0.001146
	-0.020719, -0.024043, -0.035160, -0.041635, -0.051902, -0.063884, -0.072884, -0.076738, -0.081856, -0.083761, -0.077857, -0.074651, -0.077952, -0.076310, -0.069721, -0.063240, -0.056775, -0.055188, -0.046711, -0.042996, -0.039499, -0.032268, -0.023129, -0.015735, -0.012305, -0.009383, -0.005789, -0.001996, -0.001166, -0.005106, -0.009634, -0.009864, -0.011905, -0.015913, -0.010246, -0.016645, -0.022975, -0.011972, -0.018524, 0.001048
	-0.026050, -0.019774, -0.032555, -0.037813, -0.044657, -0.054435, -0.065271, -0.071019, -0.075585, -0.077479, -0.072635, -0.069526, -0.071046, -0.070770, -0.063085, -0.055960, -0.050956, -0.049593, -0.042773, -0.034996, -0.032645, -0.029030, -0.020343, -0.011008, -0.005751, -0.003252, 0.000746, 0.003215, 0.001749, -0.000068, -0.001413, -0.002608, -0.005837, -0.007103, -0.008431, -0.012027, -0.015656, -0.014417, -0.006321, 0.003748
	-0.021728, -0.019178, -0.031232, -0.036249, -0.042206, -0.053190, -0.064017, -0.068545, -0.074597, -0.074544, -0.069543, -0.065779, -0.067928, -0.067354, -0.060655, -0.052790, -0.047723, -0.046044, -0.038188, -0.034539, -0.032080, -0.027152, -0.018902, -0.012508, -0.009304, -0.003955, -0.000288, -0.001549, -0.000556, -0.003756, -0.008467, -0.003851, -0.005999, -0.012959, -0.007423, -0.015332, -0.017388, -0.005695, -0.010807, 0.007710
	-0.028204, -0.017096, -0.027984, -0.032129, -0.038374, -0.046561, -0.059356, -0.061847, -0.069228, -0.070551, -0.065474, -0.059719, -0.059893, -0.060271, -0.053666, -0.047202, -0.041189, -0.039979, -0.033189, -0.028761, -0.025714, -0.021660, -0.014905, -0.007841, -0.004669, -0.001174, 0.001874, 0.005613, 0.005527, 0.001504, -0.000694, 0.001892, 0.001885, -0.002506, -0.005619, -0.007166, -0.009935, -0.007406, 0.000545, 0.009983
	-0.019393, -0.017785, -0.025482, -0.028146, -0.036861, -0.047528, -0.055696, -0.059118, -0.064151, -0.066346, -0.060565, -0.055661, -0.055495, -0.051944, -0.048147, -0.040645, -0.036359, -0.035990, -0.026764, -0.024843, -0.023572, -0.019648, -0.013807, -0.006811, -0.004589, -0.000266, 0.003010, 0.004931, 0.006834, 0.003254, -0.001690, 0.003120, 0.001036, -0.005283, 0.000659, -0.007399, -0.010996, -0.000832, -0.006381, 0.012135
	-0.021519, -0.010062, -0.018662, -0.023011, -0.029067, -0.036961, -0.043194, -0.048197, -0.053632, -0.055489, -0.050054, -0.045247, -0.042655, -0.040243, -0.034315, -0.027094, -0.022697, -0.021644, -0.015333, -0.010768, -0.013712, -0.012051, -0.005326, 0.000560, 0.005300, 0.007429, 0.009930, 0.015968, 0.016454, 0.012383, 0.010385, 0.011612, 0.011413, 0.008357, 0.006831, 0.005524, 0.003087, 0.003507, 0.009876, 0.018892
	-0.017331, -0.015238, -0.021971, -0.024651, -0.029507, -0.040209, -0.044232, -0.046101, -0.052689, -0.053151, -0.047133, -0.042985, -0.040475, -0.037020, -0.029999, -0.021348, -0.018232, -0.017876, -0.013058, -0.008535, -0.013279, -0.011527, -0.006296, -0.001615, 0.002270, 0.006991, 0.010272, 0.013407, 0.015950, 0.012503, 0.008026, 0.013701, 0.011513, 0.004867, 0.010667, 0.006774, 0.003571, 0.012416, 0.004875, 0.020961
	-0.022637, -0.011107, -0.018340, -0.023896, -0.028320, -0.038092, -0.041212, -0.041642, -0.044537, -0.046015, -0.041699, -0.035805, -0.033527, -0.030911, -0.022925, -0.010175, -0.007279, -0.008644, -0.005065, -0.000597, -0.003797, -0.004052, 0.000635, 0.006175, 0.010857, 0.012993, 0.016956, 0.022765, 0.023298, 0.020262, 0.018285, 0.019467, 0.021161, 0.018785, 0.017891, 0.017817, 0.013874, 0.012825, 0.015904, 0.025844
	-0.014532, -0.010189, -0.019385, -0.022584, -0.028159, -0.037803, -0.040566, -0.038125, -0.040339, -0.038899, -0.033171, -0.028143, -0.025641, -0.019755, -0.012463, -0.003824, -0.000871, -0.002698, -0.000197, 0.001952, -0.001353, -0.000188, 0.004902, 0.012600, 0.014373, 0.016449, 0.018872, 0.022822, 0.026385, 0.020681, 0.015275, 0.021387, 0.023535, 0.016733, 0.022161, 0.018819, 0.011276, 0.020785, 0.014683, 0.032409
	-0.016972, -0.004835, -0.015539, -0.019706, -0.022971, -0.032222, -0.037732, -0.035551, -0.033892, -0.031679, -0.024624, -0.019946, -0.016412, -0.010040, -0.003445, 0.005991, 0.008364, 0.006410, 0.008289, 0.009260, 0.007409, 0.008691, 0.015230, 0.022729, 0.025465, 0.025502, 0.026102, 0.030309, 0.031861, 0.026963, 0.024651, 0.027000, 0.029039, 0.025577, 0.027217, 0.027660, 0.023245, 0.021705, 0.026383, 0.034120
	-0.007042, -0.003943, -0.013314, -0.016082, -0.020497, -0.030911, -0.035096, -0.030889, -0.029351, -0.025337, -0.018980, -0.012449, -0.008879, -0.001902, 0.003577, 0.011256, 0.012460, 0.010502, 0.011904, 0.011483, 0.010067, 0.013356, 0.020792, 0.027368, 0.026382, 0.028554, 0.028164, 0.029993, 0.033232, 0.028830, 0.022354, 0.027991, 0.029607, 0.020011, 0.031066, 0.031755, 0.025061, 0.037228, 0.024607, 0.041453
	-0.012463, -0.000987, -0.008994, -0.014815, -0.017487, -0.026372, -0.031392, -0.028459, -0.025402, -0.024153, -0.015566, -0.007862, -0.004579, 0.001484, 0.010757, 0.017401, 0.019536, 0.016264, 0.016278, 0.018231, 0.018193, 0.018217, 0.025442, 0.034794, 0.036179, 0.034770, 0.033985, 0.040104, 0.040404, 0.034161, 0.030977, 0.032380, 0.034144, 0.031909, 0.033231, 0.035957, 0.034171, 0.033050, 0.038776, 0.042972
	-0.002758, 0.000700, -0.008467, -0.011525, -0.018705, -0.027522, -0.031609, -0.027494, -0.026315, -0.023221, -0.014164, -0.006562, -0.002205, 0.006453, 0.013689, 0.018647, 0.017673, 0.016751, 0.017380, 0.018782, 0.019038, 0.021992, 0.027475, 0.034748, 0.036870, 0.036635, 0.035394, 0.037519, 0.038008, 0.032063, 0.025834, 0.030409, 0.033142, 0.023991, 0.034882, 0.034323, 0.030317, 0.042711, 0.030793, 0.045129
	-0.011501, 0.004979, -0.003199, -0.009532, -0.013737, -0.022490, -0.028056, -0.025047, -0.023987, -0.021727, -0.011113, -0.003633, 0.003070, 0.010580, 0.020230, 0.025058, 0.026653, 0.024592, 0.024567, 0.025613, 0.027386, 0.029282, 0.037705, 0.042901, 0.046601, 0.045443, 0.044217, 0.048155, 0.045715, 0.039788, 0.034981, 0.038594, 0.038594, 0.034532, 0.038671, 0.042065, 0.040659, 0.042101, 0.045919, 0.050030
	-0.005239, 0.006624, -0.001837, -0.005350, -0.012024, -0.022230, -0.026144, -0.022704, -0.021559, -0.017450, -0.008515, 0.000433, 0.007392, 0.014546, 0.023538, 0.029043, 0.029892, 0.027280, 0.028785, 0.030662, 0.032758, 0.032649, 0.040035, 0.046372, 0.048654, 0.050330, 0.049538, 0.049746, 0.048851, 0.041068, 0.034598, 0.041375, 0.041379, 0.030621, 0.043091, 0.044712, 0.038634, 0.053475, 0.042814, 0.059369
	-0.011843, 0.005417, 0.000007, -0.005709, -0.011391, -0.019100, -0.024151, -0.021274, -0.019356, -0.016953, -0.004422, 0.002891, 0.010688, 0.018353, 0.027665, 0.035281, 0.036655, 0.034937, 0.036795, 0.039994, 0.042705, 0.042668, 0.048600, 0.055673, 0.059602, 0.061002, 0.059934, 0.064283, 0.061835, 0.052838, 0.048644, 0.048401, 0.048158, 0.044262, 0.049173, 0.053313, 0.050054, 0.051718, 0.058112, 0.062677
	-0.003249, 0.007140, -0.000190, -0.005182, -0.010664, -0.017472, -0.021072, -0.018928, -0.015929, -0.011810, -0.001170, 0.006999, 0.014346, 0.022026, 0.033087, 0.037703, 0.039304, 0.038986, 0.040531, 0.042739, 0.044912, 0.045850, 0.052980, 0.060894, 0.062495, 0.065477, 0.066306, 0.069035, 0.066301, 0.058359, 0.048879, 0.054660, 0.053906, 0.042834, 0.051292, 0.054304, 0.049390, 0.064968, 0.053062, 0.067337
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 80.0
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Peperations]
version = 1
points = 
	0.022498, 0.020830, 0.014175, -0.000111, -0.007965, -0.011932, -0.009252, -0.003320, -0.000118, 0.004151, 0.015991, 0.024593, 0.030148, 0.034696, 0.042241, 0.043592, 0.045307, 0.051419, 0.057700, 0.066468, 0.072764, 0.085492, 0.100446, 0.113063, 0.118900, 0.122870, 0.130290, 0.129755, 0.129462, 0.124089, 0.122420, 0.123461, 0.116841, 0.117893, 0.119241, 0.115227, 0.110631, 0.109920, 0.117187, 0.124332
	0.004953, 0.000716, -0.005511, -0.010742, -0.018400, -0.024021, -0.019665, -0.013525, -0.009878, -0.004126, 0.008939, 0.016408, 0.019292, 0.023840, 0.033007, 0.033600, 0.034448, 0.041047, 0.049029, 0.052882, 0.062512, 0.072410, 0.089182, 0.103027, 0.106205, 0.110789, 0.117912, 0.115269, 0.112784, 0.106051, 0.103603, 0.104209, 0.099603, 0.105100, 0.101466, 0.099610, 0.095780, 0.096420, 0.108661, 0.108286
	-0.007933, -0.002801, -0.011350, -0.022484, -0.029473, -0.033231, -0.030354, -0.021826, -0.018408, -0.013209, 0.001640, 0.008984, 0.012027, 0.014149, 0.024334, 0.028649, 0.030597, 0.034667, 0.041223, 0.046241, 0.051968, 0.062511, 0.079099, 0.090699, 0.097837, 0.101667, 0.108218, 0.106595, 0.104490, 0.095444, 0.089512, 0.089259, 0.089179, 0.091741, 0.094161, 0.094254, 0.091002, 0.088753, 0.095405, 0.102343
	-0.010759, -0.012564, -0.018170, -0.023960, -0.033106, -0.040910, -0.038354, -0.031441, -0.026122, -0.019953, -0.006267, 0.000733, 0.002678, 0.006102, 0.015437, 0.019860, 0.022689, 0.029563, 0.035629, 0.037302, 0.045089, 0.055137, 0.070820, 0.082978, 0.087158, 0.088614, 0.094487, 0.093851, 0.091038, 0.080923, 0.074433, 0.073797, 0.073058, 0.081788, 0.080734, 0.083111, 0.078149, 0.079373, 0.091335, 0.087853
	-0.027313, -0.019238, -0.027920, -0.036645, -0.043223, -0.049872, -0.048503, -0.043853, -0.040737, -0.035179, -0.021622, -0.013493, -0.010171, -0.007317, 0.001347, 0.007440, 0.011360, 0.015985, 0.023916, 0.026329, 0.031680, 0.042865, 0.056754, 0.067621, 0.072919, 0.075964, 0.080156, 0.081233, 0.077771, 0.068443, 0.063939, 0.062251, 0.063828, 0.065094, 0.069498, 0.071735, 0.067423, 0.064065, 0.069162, 0.076272
	-0.033298, -0.035618, -0.039940, -0.043358, -0.050731, -0.061413, -0.060545, -0.055944, -0.052261, -0.045471, -0.035624, -0.027633, -0.021472, -0.017300, -0.006949, -0.002776, -0.000154, 0.006413, 0.012882, 0.014721, 0.023411, 0.031711, 0.040565, 0.054702, 0.058761, 0.061734, 0.065369, 0.066037, 0.061059, 0.053849, 0.049600, 0.048373, 0.049189, 0.054631, 0.050470, 0.056349, 0.047074, 0.049651, 0.057444, 0.057485
	-0.046284, -0.039039, -0.049010, -0.054961, -0.061001, -0.068408, -0.069602, -0.066474, -0.063117, -0.059357, -0.049570, -0.041166, -0.035441, -0.029269, -0.019658, -0.012395, -0.008906, -0.005538, 0.002012, 0.008339, 0.013216, 0.018793, 0.031185, 0.040165, 0.047175, 0.050605, 0.054283, 0.054442, 0.049166, 0.043483, 0.039000, 0.040758, 0.040857, 0.040759, 0.042263, 0.043438, 0.040051, 0.035886, 0.041332, 0.048851
	-0.049893, -0.051919, -0.058103, -0.060142, -0.067656, -0.077159, -0.079195, -0.078019, -0.075421, -0.069471, -0.060409, -0.054194, -0.044226, -0.037275, -0.027912, -0.020020, -0.016789, -0.012491, -0.003457, 0.001129, 0.004540, 0.009435, 0.018232, 0.027941, 0.035138, 0.038227, 0.042656, 0.044103, 0.038517, 0.032121, 0.029666, 0.027319, 0.029774, 0.031572, 0.028887, 0.034828, 0.023795, 0.030023, 0.033606, 0.036047
	-0.061015, -0.055279, -0.067497, -0.072234, -0.078637, -0.083600, -0.085954, -0.087271, -0.088647, -0.083447, -0.073398, -0.065920, -0.058009, -0.048810, -0.040714, -0.032533, -0.027328, -0.020402, -0.011382, -0.006547, -0.005452, -0.002712, 0.004649, 0.014201, 0.021442, 0.025510, 0.032890, 0.034711, 0.030965, 0.026329, 0.018828, 0.019246, 0.018861, 0.019611, 0.020596, 0.021396, 0.020172, 0.015723, 0.020537, 0.029677
	-0.063777, -0.066149, -0.073750, -0.076131, -0.084016, -0.091900, -0.093741, -0.094496, -0.094840, -0.089548, -0.084332, -0.077263, -0.068485, -0.061963, -0.051082, -0.043658, -0.037912, -0.032323, -0.024324, -0.019914, -0.018261, -0.013727, -0.003485, 0.004316, 0.011418, 0.017023, 0.022980, 0.024505, 0.018896, 0.014000, 0.009498, 0.006074, 0.009480, 0.007611, 0.008958, 0.010086, -0.000341, 0.010423, 0.010467, 0.016794
	-0.072341, -0.064233, -0.079217, -0.084483, -0.091050, -0.094481, -0.095378, -0.096667, -0.100564, -0.098313, -0.093254, -0.086700, -0.079209, -0.071795, -0.061313, -0.051911, -0.046317, -0.042643, -0.037228, -0.031598, -0.027431, -0.020480, -0.012883, -0.003114, 0.004746, 0.010189, 0.015911, 0.017106, 0.014037, 0.008693, 0.005120, 0.003652, -0.000532, -0.001097, 0.001984, 0.000397, -0.002089, -0.002821, 0.000529, 0.009043
	-0.068927, -0.075835, -0.083530, -0.085213, -0.091299, -0.100015, -0.101020, -0.100921, -0.103349, -0.102493, -0.098069, -0.091292, -0.083452, -0.079672, -0.069612, -0.062472, -0.055862, -0.052233, -0.046746, -0.041991, -0.035219, -0.028225, -0.018698, -0.007309, -0.002458, 0.002051, 0.006595, 0.008468, 0.005218, -0.000205, -0.003131, -0.003647, -0.006151, -0.009154, -0.005539, -0.006971, -0.015297, -0.002874, -0.005242, 0.003706
	-0.070116, -0.067835, -0.086390, -0.089881, -0.095167, -0.099194, -0.100751, -0.103794, -0.106996, -0.105835, -0.098564, -0.092154, -0.085579, -0.083053, -0.074722, -0.066442, -0.059302, -0.053429, -0.047800, -0.042952, -0.039132, -0.034614, -0.025732, -0.012689, -0.005906, 0.001101, 0.006644, 0.010980, 0.007742, 0.002526, -0.000261, -0.004094, -0.008771, -0.008465, -0.007095, -0.008952, -0.010405, -0.010446, -0.006121, 0.002024
	-0.064366, -0.071780, -0.082938, -0.085702, -0.093522, -0.099237, -0.104020, -0.105939, -0.106226, -0.104298, -0.097541, -0.091253, -0.084969, -0.082450, -0.075561, -0.066547, -0.056511, -0.051248, -0.041287, -0.037794, -0.035633, -0.028059, -0.019518, -0.010556, -0.003388, 0.002054, 0.009492, 0.011478, 0.008555, 0.004735, -0.000781, -0.006427, -0.005697, -0.010270, -0.006112, -0.011704, -0.018717, -0.002750, -0.010971, 0.000116
	-0.076795, -0.064801, -0.080209, -0.085175, -0.093457, -0.101077, -0.104981, -0.106367, -0.106821, -0.105708, -0.098545, -0.090759, -0.086929, -0.083491, -0.074306, -0.064805, -0.055933, -0.049959, -0.042853, -0.036270, -0.034463, -0.029587, -0.018780, -0.010103, -0.003533, 0.001632, 0.007909, 0.014370, 0.009281, 0.004666, -0.002974, -0.007301, -0.010185, -0.008299, -0.006340, -0.009678, -0.011333, -0.010684, -0.006289, 0.002763
	-0.067470, -0.065770, -0.074038, -0.076420, -0.085702, -0.098704, -0.101940, -0.102629, -0.101903, -0.100342, -0.093820, -0.086941, -0.083804, -0.081020, -0.067700, -0.059395, -0.054055, -0.047911, -0.039687, -0.035672, -0.032029, -0.025979, -0.017057, -0.006973, -0.001656, 0.002001, 0.007249, 0.012112, 0.006541, 0.000572, -0.006284, -0.010415, -0.012279, -0.015087, -0.007848, -0.016491, -0.019704, -0.005357, -0.013151, 0.002966
	-0.074820, -0.054794, -0.069710, -0.075127, -0.082743, -0.091434, -0.095621, -0.097541, -0.099098, -0.097422, -0.089851, -0.083594, -0.081112, -0.078942, -0.066391, -0.057457, -0.050942, -0.048077, -0.041211, -0.034391, -0.030091, -0.026047, -0.014207, -0.005090, 0.000912, 0.005316, 0.010043, 0.015509, 0.011199, 0.004513, -0.001027, -0.006694, -0.011239, -0.011162, -0.009134, -0.013596, -0.014031, -0.011306, -0.007627, 0.001767
	-0.061695, -0.056074, -0.065188, -0.067950, -0.076218, -0.088303, -0.093436, -0.092999, -0.090937, -0.090555, -0.084407, -0.080354, -0.078692, -0.074308, -0.062767, -0.052729, -0.047475, -0.043949, -0.036669, -0.031720, -0.027940, -0.020058, -0.010125, -0.000940, 0.003512, 0.007720, 0.011869, 0.015296, 0.011180, 0.003886, -0.003309, -0.003380, -0.007926, -0.011633, -0.003540, -0.014182, -0.013975, -0.003720, -0.011797, 0.006338
	-0.070864, -0.046187, -0.061128, -0.065717, -0.072715, -0.083470, -0.088292, -0.087558, -0.087628, -0.089378, -0.083768, -0.077237, -0.077063, -0.071978, -0.061635, -0.052022, -0.046913, -0.041194, -0.034314, -0.028661, -0.027048, -0.021438, -0.009769, -0.001205, 0.004637, 0.008928, 0.013264, 0.017277, 0.013442, 0.007295, 0.003623, -0.002524, -0.004256, -0.005789, -0.004213, -0.007305, -0.010487, -0.010885, -0.006086, 0.007386
	-0.059345, -0.049207, -0.056858, -0.060052, -0.066579, -0.080604, -0.086910, -0.085647, -0.085267, -0.087618, -0.081260, -0.075368, -0.073937, -0.069758, -0.058235, -0.051634, -0.045288, -0.038732, -0.032262, -0.027928, -0.024928, -0.019266, -0.007996, 0.000923, 0.005834, 0.008336, 0.013557, 0.017068, 0.012350, 0.006475, 0.000982, 0.001103, -0.006223, -0.006853, -0.000966, -0.013148, -0.013975, -0.006310, -0.011605, 0.006165
	-0.066591, -0.039715, -0.053663, -0.059514, -0.065911, -0.075018, -0.080214, -0.082968, -0.083447, -0.085380, -0.079055, -0.071985, -0.070247, -0.065856, -0.057767, -0.049975, -0.044481, -0.039103, -0.031217, -0.024927, -0.020997, -0.016440, -0.004831, 0.004061, 0.009463, 0.011160, 0.014777, 0.020638, 0.017816, 0.011360, 0.006171, 0.002164, -0.002119, -0.003117, -0.003031, -0.005156, -0.011400, -0.011762, -0.009295, -0.000001
	-0.060314, -0.046160, -0.052794, -0.054967, -0.062049, -0.074106, -0.080446, -0.081200, -0.080809, -0.080477, -0.076170, -0.070932, -0.069101, -0.063634, -0.055720, -0.049501, -0.044939, -0.040131, -0.032438, -0.022882, -0.017627, -0.012524, -0.001324, 0.006685, 0.011868, 0.013658, 0.016095, 0.021837, 0.020158, 0.012528, 0.006089, 0.005453, -0.000976, -0.002140, 0.001104, -0.010111, -0.010612, -0.007452, -0.014357, 0.001011
	-0.075633, -0.036609, -0.049346, -0.055490, -0.059336, -0.067616, -0.073859, -0.075613, -0.076372, -0.078009, -0.070627, -0.064206, -0.064430, -0.061999, -0.054551, -0.047386, -0.040817, -0.037398, -0.028062, -0.018505, -0.012195, -0.007531, 0.001481, 0.011790, 0.019955, 0.022349, 0.022131, 0.024492, 0.023359, 0.019186, 0.014655, 0.008357, 0.004176, 0.002971, 0.002955, -0.000237, -0.005884, -0.010152, -0.009506, 0.002811
	-0.059008, -0.039658, -0.046978, -0.048324, -0.052285, -0.063338, -0.069082, -0.070556, -0.070625, -0.070049, -0.064460, -0.057403, -0.056723, -0.052882, -0.046968, -0.041507, -0.033211, -0.029974, -0.022900, -0.013579, -0.008803, -0.004962, 0.005653, 0.017026, 0.028171, 0.028651, 0.024731, 0.026850, 0.023371, 0.017073, 0.015171, 0.016616, 0.005521, 0.005756, 0.007586, -0.005103, -0.006856, -0.005604, -0.006599, 0.007528
	-0.068330, -0.030233, -0.043154, -0.047439, -0.047149, -0.051149, -0.060971, -0.063014, -0.065775, -0.064636, -0.058200, -0.050987, -0.050925, -0.050115, -0.041299, -0.033907, -0.026306, -0.024199, -0.017123, -0.009196, -0.006314, -0.003809, 0.004760, 0.015324, 0.026665, 0.029649, 0.028724, 0.027131, 0.025150, 0.021808, 0.019981, 0.016766, 0.012347, 0.008776, 0.005760, -0.000224, -0.004294, -0.005879, -0.002457, 0.010054
	-0.053519, -0.031388, -0.038255, -0.037590, -0.039245, -0.046335, -0.056314, -0.057830, -0.060291, -0.058967, -0.051413, -0.045449, -0.043947, -0.042018, -0.034113, -0.025887, -0.019539, -0.017727, -0.012711, -0.005860, -0.003102, 0.000774, 0.009438, 0.015884, 0.022961, 0.024229, 0.026012, 0.029407, 0.026717, 0.020406, 0.017796, 0.020289, 0.012243, 0.009711, 0.009234, -0.005990, -0.001013, 0.000740, -0.002144, 0.013012
	-0.068972, -0.023416, -0.032912, -0.036134, -0.035915, -0.040435, -0.047452, -0.051460, -0.055021, -0.055776, -0.048697, -0.039554, -0.036785, -0.035561, -0.029056, -0.021075, -0.013416, -0.012134, -0.007237, -0.000622, 0.001662, 0.005393, 0.012038, 0.019764, 0.023514, 0.026252, 0.028191, 0.031400, 0.031365, 0.027993, 0.023275, 0.021009, 0.018930, 0.014093, 0.009022, 0.004773, 0.002094, 0.001348, 0.005643, 0.015078
	-0.050527, -0.022437, -0.028090, -0.026206, -0.028387, -0.036911, -0.041310, -0.044227, -0.046970, -0.046769, -0.038081, -0.031386, -0.029516, -0.024050, -0.019435, -0.012381, -0.005732, -0.004173, 0.000911, 0.006849, 0.007360, 0.010699, 0.017436, 0.023369, 0.028527, 0.029640, 0.031002, 0.034727, 0.036582, 0.030763, 0.026015, 0.028623, 0.020834, 0.016185, 0.016933, 0.002829, 0.004984, 0.009818, 0.008874, 0.020032
	-0.067395, -0.010220, -0.021024, -0.024567, -0.024087, -0.029620, -0.032317, -0.034341, -0.038392, -0.038789, -0.030285, -0.021590, -0.017175, -0.014435, -0.007732, -0.000529, 0.005605, 0.007078, 0.012454, 0.017758, 0.016774, 0.015574, 0.020748, 0.028369, 0.033644, 0.034771, 0.036537, 0.040293, 0.042118, 0.039979, 0.035655, 0.033354, 0.030928, 0.024890, 0.021491, 0.018938, 0.013668, 0.012501, 0.017108, 0.023515
	-0.038833, -0.012802, -0.018564, -0.017459, -0.019062, -0.027068, -0.030119, -0.028336, -0.029665, -0.030695, -0.022239, -0.013522, -0.008358, -0.004785, 0.000463, 0.010662, 0.015564, 0.016950, 0.020281, 0.025300, 0.022680, 0.022717, 0.026679, 0.031617, 0.035801, 0.037098, 0.041294, 0.045640, 0.047879, 0.042000, 0.038044, 0.040629, 0.033892, 0.031247, 0.031584, 0.018500, 0.020116, 0.019823, 0.016638, 0.029979
	-0.054356, -0.002258, -0.012712, -0.017288, -0.016713, -0.022907, -0.024293, -0.021563, -0.022620, -0.021953, -0.015330, -0.005386, -0.000764, 0.002640, 0.009997, 0.022869, 0.028174, 0.027730, 0.030977, 0.035707, 0.032818, 0.030889, 0.033638, 0.038561, 0.044265, 0.045141, 0.047683, 0.051815, 0.054004, 0.050991, 0.045574, 0.043899, 0.044055, 0.039092, 0.035909, 0.032091, 0.026891, 0.022169, 0.024865, 0.030848
	-0.031827, -0.000102, -0.006368, -0.006487, -0.006247, -0.014001, -0.017110, -0.013043, -0.010851, -0.008764, -0.000213, 0.006477, 0.011144, 0.018309, 0.024745, 0.033643, 0.038648, 0.039249, 0.041148, 0.045266, 0.041693, 0.040999, 0.045484, 0.052613, 0.057066, 0.054753, 0.055112, 0.059287, 0.060203, 0.052465, 0.047993, 0.050999, 0.047464, 0.046460, 0.044507, 0.031433, 0.032267, 0.032025, 0.029852, 0.040329
	-0.053848, 0.008122, -0.005187, -0.009032, -0.006543, -0.010012, -0.013005, -0.011663, -0.008957, -0.004668, 0.005458, 0.012800, 0.016893, 0.023554, 0.031737, 0.038741, 0.043870, 0.043337, 0.046621, 0.047581, 0.045654, 0.044827, 0.050363, 0.058747, 0.061023, 0.060485, 0.059059, 0.061821, 0.061391, 0.055971, 0.051067, 0.050038, 0.051018, 0.046533, 0.043334, 0.042562, 0.036118, 0.029798, 0.032773, 0.039524
	-0.025830, 0.006164, -0.000655, 0.000164, 0.000088, -0.008033, -0.011008, -0.006017, -0.001301, 0.004088, 0.011848, 0.020276, 0.024465, 0.033383, 0.039126, 0.044268, 0.047916, 0.047402, 0.050050, 0.050456, 0.048891, 0.051771, 0.058154, 0.063246, 0.065463, 0.063072, 0.060950, 0.065351, 0.064614, 0.057455, 0.051194, 0.055723, 0.050906, 0.046407, 0.048283, 0.036561, 0.037400, 0.036887, 0.031589, 0.046759
	-0.041184, 0.017683, 0.006408, 0.000358, 0.001923, -0.002498, -0.003907, -0.001746, 0.001864, 0.006784, 0.017297, 0.026916, 0.030940, 0.036439, 0.045987, 0.050809, 0.054636, 0.052055, 0.053180, 0.056698, 0.057069, 0.055779, 0.063193, 0.067815, 0.071856, 0.070651, 0.067674, 0.070718, 0.070797, 0.062598, 0.057842, 0.056835, 0.056713, 0.051260, 0.048727, 0.048227, 0.044844, 0.039559, 0.041218, 0.044920
	-0.014008, 0.018619, 0.011274, 0.010878, 0.008771, 0.001246, -0.001819, 0.003600, 0.008052, 0.011983, 0.021970, 0.030757, 0.037662, 0.045972, 0.053195, 0.057661, 0.059206, 0.058383, 0.060240, 0.061039, 0.062504, 0.064497, 0.070278, 0.077704, 0.080246, 0.077015, 0.072985, 0.075685, 0.072584, 0.063534, 0.057732, 0.061938, 0.057545, 0.050931, 0.054863, 0.045820, 0.048882, 0.049675, 0.043484, 0.051538
	-0.045038, 0.028947, 0.019821, 0.012917, 0.013648, 0.007951, 0.005122, 0.007823, 0.012411, 0.015320, 0.025036, 0.036734, 0.045314, 0.052208, 0.062220, 0.065610, 0.068489, 0.066665, 0.068454, 0.069025, 0.071080, 0.073373, 0.079623, 0.085651, 0.088907, 0.088954, 0.084254, 0.084464, 0.080300, 0.072471, 0.067316, 0.066430, 0.065143, 0.057630, 0.058650, 0.059627, 0.057197, 0.054105, 0.055295, 0.057879
	-0.017117, 0.027364, 0.023067, 0.022758, 0.019246, 0.011825, 0.007962, 0.011522, 0.017237, 0.021779, 0.031329, 0.042642, 0.052349, 0.060322, 0.069568, 0.074657, 0.075211, 0.072882, 0.075373, 0.078391, 0.079512, 0.081816, 0.086101, 0.091730, 0.095061, 0.095682, 0.092100, 0.092873, 0.085769, 0.077219, 0.068392, 0.073179, 0.069972, 0.061240, 0.068306, 0.062227, 0.061008, 0.064520, 0.058543, 0.070728
	-0.042759, 0.035472, 0.029514, 0.023812, 0.024176, 0.020576, 0.017397, 0.018716, 0.022981, 0.027634, 0.041262, 0.050991, 0.058558, 0.067060, 0.077829, 0.083609, 0.084719, 0.082815, 0.085352, 0.087363, 0.091238, 0.091692, 0.096562, 0.102513, 0.106436, 0.108184, 0.105828, 0.107257, 0.102415, 0.090768, 0.084257, 0.081410, 0.081286, 0.073523, 0.074433, 0.076576, 0.070376, 0.068350, 0.071896, 0.072962
	-0.003143, 0.035517, 0.033266, 0.032727, 0.031843, 0.025862, 0.023177, 0.026936, 0.032953, 0.037457, 0.049289, 0.057429, 0.066625, 0.072540, 0.083814, 0.089321, 0.092420, 0.093053, 0.094752, 0.096876, 0.098364, 0.101271, 0.105185, 0.113505, 0.115784, 0.118957, 0.117138, 0.117934, 0.110930, 0.101497, 0.091051, 0.092731, 0.090574, 0.079282, 0.084691, 0.078426, 0.073451, 0.081698, 0.072811, 0.084352
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 19.8
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 130, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 123, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 112, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/neopixel.py", line 111, in load_config_prefix
    return PrinterNeoPixel(config)
  File "/home/pi/klipper/klippy/extras/neopixel.py", line 42, in __init__
    raise config.error("neopixel chain too long")
configparser.Error: neopixel chain too long
webhooks client 4132169496: New connection
webhooks client 4132169496: Client info {'program': 'Moonraker', 'version': 'v0.9.3-0-g71f9e67'}
Starting Klippy...
Args: ['/home/pi/klipper/klippy/klippy.py', '/home/pi/printer_data/config/printer.cfg', '-l', '/home/pi/printer_data/logs/klippy.log', '-I', '/home/pi/printer_data/comms/klippy.serial', '-a', '/home/pi/printer_data/comms/klippy.sock']
Git version: 'v0.12.0-402-g2817b348e-dirty'
Untracked files: klippy/extras/beacon.py, klippy/extras/beacon_adaptive_heat_soak.py, klippy/extras/beacon_mesh.py, klippy/extras/beacon_true_zero_correction.py, klippy/extras/beacon_user_z_offset.py, klippy/extras/fastconfig.py, klippy/extras/gcode_shell_command.py, klippy/extras/linear_movement_vibrations.py, klippy/extras/named_offsets.py, klippy/extras/ratos.py, (+4 files)
Branch: master
Remote: origin
Tracked URL: https://github.com/Klipper3d/klipper.git
CPU: 4 core ?
Python: '3.9.2 (default, Jan 24 2026, 09:41:14) \n[GCC 10.2.1 20210110]'
Start printer at Tue Mar 17 03:54:34 2026 (1773719674.3 9278.7)
===== Config file =====
[mcu rpi]
serial = /tmp/klipper_host_mcu

[board_pins btt-octopus-pro-h723-11]
aliases = 
	
	
	
	x_step_pin=PF13,
	x_dir_pin=PF12,
	x_enable_pin=PF14,
	x_uart_pin=PC4,
	x_diag_pin=PG6,
	x_endstop_pin=PG6,
	
	
	
	dual_carriage_step_pin=PF9,
	dual_carriage_dir_pin=PF10,
	dual_carriage_enable_pin=PG2,
	dual_carriage_uart_pin=PF2,
	dual_carriage_diag_pin=PG12,
	dual_carriage_endstop_pin=PG12,
	
	
	
	y_step_pin=PG0,
	y_dir_pin=PG1,
	y_enable_pin=PF15,
	y_uart_pin=PD11,
	y_diag_pin=PG9,
	y_endstop_pin=PG9,
	
	
	
	y1_step_pin=PG4,
	y1_dir_pin=PC1,
	y1_enable_pin=PA2,
	y1_uart_pin=PC7,
	y1_diag_pin=PG11,
	y1_endstop_pin=PG11,
	
	
	
	z0_step_pin=PC13,
	z0_dir_pin=PF0,
	z0_enable_pin=PF1,
	z0_uart_pin=PE4,
	z0_diag_pin=PG13,
	
	
	
	z1_step_pin=PE2,
	z1_dir_pin=PE3,
	z1_enable_pin=PD4,
	z1_uart_pin=PE1,
	z1_diag_pin=PG14,
	
	
	
	z2_step_pin=PE6,
	z2_dir_pin=PA14,
	z2_enable_pin=PE0,
	z2_uart_pin=PD3,
	z2_diag_pin=PG15,
	
	e_step_pin=PF11,
	e_dir_pin=PG3,
	e_enable_pin=PG5,
	e_uart_pin=PC6,
	
	e_heater_pin=PA2,
	e_sensor_pin=PF4,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=PA7,
	stepper_spi_miso_pin=PA6,
	stepper_spi_sclk_pin=PA5,
	adxl345_cs_pin=PA15,
	bltouch_sensor_pin=PB7,
	bltouch_control_pin=PB6,
	probe_pin=PB7,
	fan_part_cooling_pin=PA8,
	fan_toolhead_cooling_pin=PE5,
	fan_controller_board_pin=PD12,
	heater_bed_heating_pin=PA1,
	heater_bed_sensor_pin=PF3,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PG15,
	filament_sensor_motion_pin=PG14,
	ratrig_vaoc_probe_pin=PG10,
	ratrig_vaoc_led_pin=PB0,
	ratrig_vaoc_fan_pin=PD13,
	chamber_lighting_pin=PB11,
	chamber_filter_4p_fan_pin=PD14,
	chamber_filter_4p_fan_enable_pin=PD15

[mcu]
serial = /dev/RatOS/btt-octopus-pro-h723-11

[temperature_sensor Octopus_Pro_H723_V1.1]
sensor_type = temperature_mcu

[adxl345 controlboard]
cs_pin = PA15
spi_software_mosi_pin = PB5
spi_software_miso_pin = PB4
spi_software_sclk_pin = PB3

[board_pins toolboard_t0]
mcu = toolboard_t0
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t0]
serial = /dev/RatOS/btt-ebb42-gen2-10-t0

[temperature_sensor EBB42_Gen2_v1.0_T0]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t0

[lis2dw toolboard_t0]
axes_map = x, z, y
cs_pin = toolboard_t0:PB1
spi_software_mosi_pin = toolboard_t0:PB11
spi_software_miso_pin = toolboard_t0:PB2
spi_software_sclk_pin = toolboard_t0:PB10

[board_pins toolboard_t1]
mcu = toolboard_t1
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t1]
serial = /dev/RatOS/btt-ebb42-gen2-10-t1

[temperature_sensor EBB42_Gen2_v1.0_T1]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t1

[lis2dw toolboard_t1]
axes_map = x, z, y
cs_pin = toolboard_t1:PB1
spi_software_mosi_pin = toolboard_t1:PB11
spi_software_miso_pin = toolboard_t1:PB2
spi_software_sclk_pin = toolboard_t1:PB10

[gcode_macro RatOS]
variable_homing = "endstops"
variable_z_probe = "static"
variable_sensorless_x_current = 0.6
variable_sensorless_y_current = 0.9
variable_safe_home_x = "middle"
variable_safe_home_y = "middle"
variable_driver_type_x = "tmc2209"
variable_driver_type_y = "tmc2209"
variable_stowable_probe_stop_on_error = False
variable_chamber_filter_enable = True
variable_chamber_filter_speed = 0.5
variable_chamber_filter_disable_speed = 1.0
variable_chamber_filter_enable_at = "after_print_start"
variable_chamber_filter_disable_period = 300
variable_chamber_filter_disable_bed_temp = 0
variable_chamber_heater_enable = True
variable_chamber_heater_bed_temp = 115
variable_chamber_heater_preheating_temp = 150
variable_chamber_heater_heating_temp_offset = 25
variable_chamber_heater_control_external_heater = False
variable_chamber_heater_air_circulation_enable = True
variable_chamber_heater_air_circulation_fan_speed = 0.35
variable_chamber_heater_air_circulation_y_pos = 0
variable_chamber_heater_air_circulation_z_pos = 100
variable_chamber_heater_extra_fan_speed = 1.0
variable_chamber_heater_filter_fan_speed = 1.0
variable_bed_heat_soak_time = 0
variable_hotend_heat_soak_time = 0
variable_led_status_action = 0.0,1.0,1.0
variable_led_status_success = 0.0,1.0,0.0
variable_led_status_error = 1.0,0.0,1.0
variable_led_status_on = 1.0,1.0,1.0
variable_led_status_off = 0.0,0.0,1.0
variable_led_status_standby = 0.1,0.1,0.1
variable_led_status_heating = 1.0,0.0,0.0
variable_led_status_cooling = 0.0,0.0,1.0
variable_calibrate_bed_mesh = True
variable_adaptive_mesh = True
variable_start_print_park_in = "center"
variable_start_print_park_z_height = 3
variable_end_print_park_in = "back"
variable_pause_print_park_in = "back"
variable_end_print_park_z_hop = 20
variable_nozzle_priming = "primeblob"
variable_nozzle_prime_start_x = "max"
variable_nozzle_prime_start_y = "min"
variable_nozzle_prime_direction = "auto"
variable_nozzle_prime_bridge_fan = 102
variable_probe_for_priming_result = None
variable_probe_for_priming_end_result = None
variable_probe_for_priming_result_t1 = None
variable_probe_for_priming_end_result_t1 = None
variable_probe_for_priming_disable_mesh_constraints = False
variable_adaptive_prime_offset_threshold = -1.0
variable_last_z_offset = None
variable_runout_park_in = "front"
variable_enable_unload_tip_forming = False
variable_filament_unload_length = 150
description = RatOS variable storage macro, will echo variables to the console when run.
variable_relative_extrusion = True
variable_force_absolute_position = False
variable_preheat_extruder = True
variable_preheat_extruder_temp = 150
variable_macro_travel_speed = 600
variable_macro_travel_accel = 8000
variable_macro_z_speed = 15
variable_bed_margin_x = [59.6, 59.6]
variable_bed_margin_y = [14.35, 33.65]
variable_printable_x_min = 0
variable_printable_x_max = 0
variable_printable_y_min = 0
variable_printable_y_max = 0
variable_end_print_motors_off = True
variable_status_color_ok = "00FF00"
variable_status_color_error = "FF0000"
variable_status_color_unknown = "FFFF00"
variable_end_print_retract_filament = 10
gcode = 
	ECHO_RATOS_VARS
variable_auto_center_subject = False
variable_toolchange_zhop = 2.0
variable_toolchange_zspeed = 25
variable_toolchange_sync_fans = False
variable_toolchange_combined_zhop = False
variable_toolchange_travel_speed = 600
variable_toolchange_travel_accel = 8000
variable_toolchange_extrusion = 2.0
variable_toolchange_retraction = 2.0
variable_toolchange_feedrate = 7200
variable_toolchange_prepurging_timer = 0
variable_toolchange_standby_temp = -1
variable_toolchange_purge = 25
variable_toolchange_first_purge = 50
variable_beacon_bed_mesh_scv = 25
variable_beacon_contact_z_homing = False
variable_beacon_contact_start_print_true_zero = True
variable_beacon_contact_start_print_true_zero_fuzzy_position = True
variable_beacon_contact_calibrate_model_on_true_zero = True
variable_beacon_contact_wipe_before_true_zero = True
variable_beacon_contact_wipe_before_true_zero_method = "probe_clean"
variable_beacon_contact_true_zero_temp = 170
variable_beacon_contact_prime_probing = True
variable_beacon_contact_expansion_compensation = True
variable_beacon_contact_bed_mesh = False
variable_beacon_contact_bed_mesh_samples = 2
variable_beacon_contact_z_tilt_adjust = False
variable_beacon_contact_z_tilt_adjust_samples = 2
variable_beacon_scan_compensation_enable = True
variable_beacon_scan_compensation_profile = "auto"
variable_beacon_scan_compensation_desired_spacing = 10
variable_beacon_scan_compensation_bed_temp_mismatch_is_error = False
variable_beacon_contact_poke_bottom_limit = -1
variable_beacon_scan_method_automatic = False
variable_beacon_adaptive_heat_soak = True
variable_beacon_adaptive_heat_soak_max_wait = 5400
variable_beacon_adaptive_heat_soak_extra_wait_after_completion = 0
variable_beacon_adaptive_heat_soak_layer_quality = 3
variable_beacon_adaptive_heat_soak_maximum_first_layer_duration = 1800
variable_beacon_contact_start_print_true_zero_fuzzy_radius = 20
variable_homing_x = "endstop"
variable_homing_y = "endstop"
variable_default_toolhead = 0
variable_adxl_chip = ["lis2dw toolboard_t0", "lis2dw toolboard_t1"]
variable_shaper_x_freq = [54.2, 53.2, 53.6, 54.4]
variable_shaper_y_freq = [40.8, 47.6, 38.6, 38]
variable_shaper_x_type = ["mzv", "mzv", "mzv", "mzv"]
variable_shaper_y_type = ["mzv", "mzv", "mzv", "mzv"]
variable_x_driver_types = ["tmc5160"]
variable_x_axes = ["x"]
variable_y_driver_types = ["tmc5160", "tmc5160"]
variable_y_axes = ["y", "y1"]
variable_z_driver_types = ["tmc2209", "tmc2209", "tmc2209"]
variable_z_axes = ["z", "z1", "z2"]
variable_home_y_first = True

[ratos_homing]
axes = xyz
z_hop = 15
z_hop_speed = 15
gcode = 
	
	_LED_ON
	
	
	{% set prev_stop_on_error = printer["gcode_macro RatOS"].stowable_probe_stop_on_error %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set target_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	_IDEX_SINGLE
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE=True
	
	
	M400
	
	G90
	
	
	{% set X = true if params.X is defined else false %}
	{% set Y = true if params.Y is defined else false %}
	{% set Z = true if params.Z is defined else false %}
	{% if printer["gcode_macro RatOS"].home_y_first|default(false)|lower == 'true' %}
	HOME_Y X={X} Y={Y} Z={Z}
	HOME_X X={X} Y={Y} Z={Z}
	{% else %}
	HOME_X X={X} Y={Y} Z={Z}
	HOME_Y X={X} Y={Y} Z={Z}
	{% endif %}
	HOME_Z X={X} Y={Y} Z={Z}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE={prev_stop_on_error}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[gcode_macro HOME_X]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_x = printer["gcode_macro RatOS"].homing_x|lower %}
	{% set homing_x = homing_x if homing_x else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_X" MSG="printable_x_max: {printable_x_max}, safe_home_x: {safe_home_x}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}"
	
	
	{% if X or not Y and not Z %}
	{% if homing_x == 'endstop' %}
	G28 X
	{% elif homing_x == 'sensorless' %}
	{% if printer["dual_carriage"] is defined %}
	{ action_emergency_stop("sensorless homing not supported on IDEX!") }
	{% endif %}
	HOME_X_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_x to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_x, homing)) }
	{% endif %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1} MODE=PRIMARY
	G1 X{parking_position} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	{% endif %}
	{% set x_homed = True %}
	G0 X{safe_home_x} F{speed}
	M400
	{% endif %}

[gcode_macro HOME_Y]
gcode = 
	
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_y = printer["gcode_macro RatOS"].homing_y|lower %}
	{% set homing_y = homing_y if homing_y else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Y" MSG="printable_y_max: {printable_y_max}, safe_home_y: {safe_home_y}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}"
	
	
	{% if Y or not X and not Z %}
	{% if homing_y == 'endstop' %}
	G28 Y
	{% elif homing_y == 'sensorless' %}
	HOME_Y_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_y to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_y, homing)) }
	{% endif %}
	{% set y_homed = True %}
	G0 Y{safe_home_y} F{speed}
	{% endif %}

[gcode_macro HOME_Z]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	
	
	{% set beacon_contact_z_homing = true if printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_z_home_position_fuzzing_radius = printer["gcode_macro RatOS"].beacon_z_home_position_fuzzing_radius|default(0)|float %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Z" MSG="x_homed: {x_homed}, y_homed: {y_homed}, z_probe: {z_probe}, beacon_contact_z_homing: {beacon_contact_z_homing}"
	
	
	{% if Z or not Y and not X %}
	RATOS_ECHO MSG="Homing Z"
	{% if x_homed == False or y_homed == False %}
	{ action_emergency_stop("X and Y must be homed before homing Z") }
	{% else %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_homing %}
	{% if beacon_contact_start_print_true_zero %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% else %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	{% else %}
	G28 Z
	{% endif %}
	_Z_HOP
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro HOME_X_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	
	G4 P300
	
	G28 X
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"

[gcode_macro HOME_Y_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	
	G4 P300
	
	G28 Y
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"

[gcode_macro _Z_HOP]
description = Move Z axis up by Z_HOP distance at Z_HOP_SPEED. In relative mode it will move Z axis up by Z_HOP distance. In absolute mode it will move Z axis to Z_HOP distance.
gcode = 
	{% set z_hop = printer.fastconfig.config.ratos_homing.z_hop|float %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	G0 Z{z_hop} F{z_hop_speed}

[gcode_macro __MOVE_TO_SAFE_Z_HOME_ECHO_DEBUG]
gcode = 
	DEBUG_ECHO PREFIX="_MOVE_TO_SAFE_Z_HOME" MSG="x: {params.X}, y: {params.Y}, z_hop: {params.Z_HOP}, fuzzy_radius: {params.FUZZY_RADIUS}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}, printable_x_max: {printer['gcode_macro RatOS'].printable_x_max}, printable_y_max: {printer['gcode_macro RatOS'].printable_y_max}"

[gcode_macro MAYBE_HOME]
description = Only home unhomed axis. Specify ABL=1 to also ensure that automatic bed levelling is applied (if configured).
variable_is_kinematic_position_overriden = False
gcode = 
	{% set abl = params.ABL|default('')|lower in ('true', 'yes', '1') %}
	{% if printer["gcode_macro MAYBE_HOME"].is_kinematic_position_overriden|lower == 'true' %}
	RATOS_ECHO MSG="SET_CENTER_KINEMATIC_POSITION has been abused. Homing all axes. Please refrain from using SET_CENTER_KINEMATIC_POSITION outside of debugging purposes."
	G28
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=False
	{% else %}
	{% set axes = '' %}
	{% set isHomed = true %}
	{% set axesToHome = '' %}
	{% if params.X is defined %}
	{% set axes = axes ~ 'X ' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% endif %}
	{% if params.Y is defined %}
	{% set axes = axes ~ 'Y ' %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% endif %}
	{% if params.Z is defined %}
	{% set axes = axes ~ 'Z ' %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if params.X is not defined and params.Y is not defined and params.Z is not defined %}
	{% set axes = '' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if isHomed is false %}
	RATOS_ECHO MSG="Homing {axesToHome}"
	G28 {axesToHome}
	{% else %}
	RATOS_ECHO MSG="All requested axes already homed. Skipping homing."
	{% endif %}
	{% endif %}
	{% if abl %}
	{% if printer.z_tilt is defined %}
	{% if not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Performing Z tilt adjustment..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Z tilt already applied. Skipping Z tilt adjustment."
	{% endif %}
	{% elif printer.quad_gantry_level is defined %}
	{% if not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Performing quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Quad gantry leveling already applied. Skipping quad gantry leveling."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="No automatic bed leveling method configured. Skipping bed leveling."
	{% endif %}
	{% endif %}

[gcode_macro PID_CALIBRATE_HOTEND]
description = Perform a PID calibration test for a given extruder heater.
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set temp = params.TEMP|default(220)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_HOTEND" MSG="TEMP={temp}"
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO MSG="PID calibration hotend heater T0 at {temp}°C..."
	PID_CALIBRATE HEATER=extruder TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	
	{% if toolhead==0 or toolhead==1 %}
	RATOS_ECHO MSG="PID calibration hotend heater T{toolhead} at {temp}°C..."
	PID_CALIBRATE HEATER=extruder{'' if toolhead==0 else toolhead} TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_BED]
description = Perform a PID calibration test for the bed heater.
gcode = 
	
	{% set temp = params.TEMP|default(80)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_BED" MSG="TEMP={temp}"
	RATOS_ECHO MSG="PID calibration bed heater at {temp}°C..."
	
	
	PID_CALIBRATE HEATER=heater_bed TARGET={temp}
	
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_CHAMBER_HEATER]
description = Perform a PID calibration test for the chamber heater.
gcode = 
	
	{% set temp = params.TEMP|default(150)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_CHAMBER_HEATER" MSG="TEMP={temp}"
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	RATOS_ECHO MSG="PID calibration chamber heater at {temp}°C..."
	PID_CALIBRATE HEATER=chamber_heater TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_heater" %}
	{% set link_text = "RatOS Chamber Heater" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber heater found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro INITIALIZE_PA_TUNING]
description = Start a pressure advance tuning tower.
gcode = 
	
	{% set start = params.START|default(0.0)|float %}
	{% set factor = params.FACTOR|default(0.001)|float %}
	
	
	{% set layer_number = printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|default(0)|int %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if is_printing_gcode and layer_number < 2 %}
	DEBUG_ECHO PREFIX="START_PA_TOWER" MSG="START: {start}, FACTOR: {factor}"
	RATOS_ECHO MSG="Starting pressure advance tuning tower..."
	TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START={start} FACTOR={factor}
	{% else %}
	RATOS_ECHO MSG="Pressure advance tuning tower requires you to be printing gcode and on layer 1 to start."
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro CHAMBER_FILTER_ON]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	_CHAMBER_FILTER_TURN_ON
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro CHAMBER_FILTER_OFF]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Deactivating chamber filter..."
	_CHAMBER_FILTER_TURN_OFF
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set chamber_filter_enable_at = printer["gcode_macro RatOS"].chamber_filter_enable_at|default('after_print_start')|lower %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_ON" MSG="at: {at}, chamber_filter_enable: {chamber_filter_enable}, chamber_filter_enable_at: {chamber_filter_enable_at}, chamber_filter_speed: {chamber_filter_speed}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	{% if chamber_filter_enable_at == at %}
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	
	
	_CHAMBER_FILTER_TURN_ON AT={at}
	
	
	{% if chamber_filter_enable_at == "print_end" %}
	_LED_CHAMBER_FILTER_ON
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_OFF]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF" MSG="chamber_filter_enable: {chamber_filter_enable}, filter_disable_period: {filter_disable_period}, filter_disable_bed_temp: {filter_disable_bed_temp}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	
	{% if filter_disable_period > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting {filter_disable_period} seconds before turning chamber filter off..."
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION={filter_disable_period}
	{% endif %}
	
	
	{% if filter_disable_bed_temp > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting for bed temp to cool down to {filter_disable_bed_temp}°C to turn filter off..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM=0 MAXIMUM={filter_disable_bed_temp}
	_CHAMBER_FILTER_TURN_OFF
	_LED_CHAMBER_FILTER_OFF
	{% endif %}
	
	{% endif %}

[delayed_gcode _CHAMBER_FILTER_OFF_TIMER]
gcode = 
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF_TIMER" MSG="executed"
	
	
	_CHAMBER_FILTER_TURN_OFF
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Chamber filter turned off!"
	
	
	_LED_CHAMBER_FILTER_OFF

[gcode_macro _CHAMBER_FILTER_TURN_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_speed|default(0)|float %}
	{% if at == "print_end" %}
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_disable_speed|default(0)|float %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION=0
	
	
	SET_FAN_SPEED FAN=filter SPEED={chamber_filter_speed}

[gcode_macro _CHAMBER_FILTER_TURN_OFF]
gcode = 
	
	SET_FAN_SPEED FAN=filter SPEED=0

[gcode_macro _CHAMBER_FILTER_SANITY_CHECK]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	{% if filter_disable_bed_temp > 0 and filter_disable_period > 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable, not both.")}
	{% endif %}
	
	{% if filter_disable_bed_temp == 0 and filter_disable_period == 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable.")}
	{% endif %}
	
	{% endif %}

[gcode_macro CHAMBER_HEATER_ON]
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(45)|int %}
	
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp} IS_FROM_START_PRINT=False

[gcode_macro CHAMBER_HEATER_OFF]
gcode = 
	_CHAMBER_HEATER_OFF

[gcode_macro _CHAMBER_HEATER_ON]
variable_chamber_temp = 0
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	{% set is_from_start_print = true if params.IS_FROM_START_PRINT|default(True)|lower == 'true' else false %}
	
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set chamber_heater_enable = true if printer["gcode_macro RatOS"].chamber_heater_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}
	{% set chamber_heater_preheating_temp = printer["gcode_macro RatOS"].chamber_heater_preheating_temp|default(150)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	{% set chamber_heater_control_external_heater = true if printer["gcode_macro RatOS"].chamber_heater_control_external_heater|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_enable = true if printer["gcode_macro RatOS"].chamber_heater_air_circulation_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_fan_speed = printer["gcode_macro RatOS"].chamber_heater_air_circulation_fan_speed|default(0.35)|float %}
	{% set chamber_heater_air_circulation_y_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_y_pos|default(0)|float %}
	{% set chamber_heater_air_circulation_z_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_z_pos|default(100)|float %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_HEATER_ON" MSG="chamber_heater_enable: {chamber_heater_enable}, chamber_heater_preheating_temp: {chamber_heater_preheating_temp}, chamber_heater_heating_temp_offset: {chamber_heater_heating_temp_offset}, bed_temp: {bed_temp}, chamber_temp: {chamber_temp}, start_chamber_temp: {start_chamber_temp}"
	
	
	{% if chamber_heater_enable and chamber_temp > 0 and chamber_heater_bed_temp > 0 %}
	
	
	_LED_HEATING
	
	
	RATOS_ECHO MSG="Preheating chamber to {(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}°C..."
	
	
	{% set chamber_temp_sensor = "extruder" %}
	{% if printer["dual_carriage"] is defined and default_toolhead == 1 %}
	{% set chamber_temp_sensor = "extruder1" %}
	{% endif %}
	{% if printer["temperature_sensor chamber"] is defined %}
	{% set chamber_temp_sensor = "temperature_sensor chamber" %}
	{% endif %}
	
	
	{% set current_chamber_temp = printer['%s' % chamber_temp_sensor].temperature|int %}
	
	
	{% set needs_heating = current_chamber_temp < (start_chamber_temp if start_chamber_temp > 0 else chamber_temp) %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_BEFORE_PREHEATING
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	{% if not is_from_start_print %}
	MAYBE_HOME
	{% endif %}
	G0 Z{chamber_heater_air_circulation_z_pos} F{z_speed}
	G0 Y{chamber_heater_air_circulation_y_pos} F{speed}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * chamber_heater_air_circulation_fan_speed)}
	{% endif %}
	{% else %}
	{% if is_from_start_print %}
	G0 Z{z} F{z_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE={chamber_temp}
	
	
	{% if needs_heating %}
	
	
	M140 S{chamber_heater_bed_temp}
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={chamber_heater_preheating_temp}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	
	{% endif %}
	
	
	{% if needs_heating %}
	_CHAMBER_HEATER_EXTRA_FAN_ON
	{% endif %}
	
	
	{% if needs_heating %}
	TEMPERATURE_WAIT SENSOR="{chamber_temp_sensor}" MINIMUM={(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% endif %}
	
	
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED=0
	_CHAMBER_FILTER_ON AT="before_print_start"
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	G28 Z
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_AFTER_PREHEATING
	{% endif %}
	
	
	{% if printer["temperature_sensor chamber"] is defined %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined and chamber_heater_control_external_heater %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	
	
	_LED_SUCCESS
	
	{% endif %}

[gcode_macro _CHAMBER_HEATER_OFF]
gcode = 
	RATOS_ECHO MSG="Deactivating chamber heater..."
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=0
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE=0
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	
	
	_CHAMBER_HEATER_EXTRA_FAN_OFF

[delayed_gcode _CHAMBER_HEATER_CONTROL]
initial_duration = 0.
gcode = 
	
	{% set chamber_temp = printer["gcode_macro _CHAMBER_HEATER_ON"].chamber_temp|default(0)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	
	
	{% set current_chamber_temp = printer['temperature_sensor chamber'].temperature|int %}
	
	
	{% if current_chamber_temp < chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	{% endif %}
	
	
	{% if current_chamber_temp >= chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_ON]
gcode = 
	
	{% set chamber_heater_extra_fan_speed = printer["gcode_macro RatOS"].chamber_heater_extra_fan_speed|default(0.0)|float %}
	
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	{% if chamber_heater_extra_fan_speed > 0 %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED={chamber_heater_extra_fan_speed}
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_OFF]
gcode = 
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED=0
	{% endif %}

[gcode_macro _USER_CHAMBER_HEATER_BEFORE_PREHEATING]
description = Will be executed before chamber preheating, only if heating is needed.
gcode = 

[gcode_macro _USER_CHAMBER_HEATER_AFTER_PREHEATING]
description = Will be executed after chamber preheating, only if heating was needed.
gcode = 

[gcode_macro RESET_HEATSOAK_SETTINGS]
description = Resets all heatsoak-related settings to startup defaults
gcode = 
	HEATSOAK_SETTINGS ACTION=reset

[gcode_macro USE_ADAPTIVE_HEATSOAK]
description = Temporarily enables adaptive bed heatsoaking (if a beacon probe is present), will reset to printer.cfg settings
	when Klipper is restarted. Optionally specify QUALITY (1-5) and maximum FIRST_LAYER_DURATION (in minutes).
	Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.QUALITY|default("1..5") %}
	{% set _ = params.FIRST_LAYER_DURATION|default("1..120 minutes") %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("Adaptive heatsoaking is only available when a beacon probe is configured.") }
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_quality = (settings.variable_beacon_adaptive_heat_soak_layer_quality if defsrc == 'startup' else current.beacon_adaptive_heat_soak_layer_quality)|default(3)|int %}
	{% set default_first_layer_duration_secs = (settings.variable_beacon_adaptive_heat_soak_maximum_first_layer_duration if defsrc == 'startup' else current.beacon_adaptive_heat_soak_maximum_first_layer_duration)|default(1800)|int %}
	{% if params2.QUALITY is defined %}
	{% set quality = params2.QUALITY|int %}
	{% if quality < 1 or quality > 5 %}
	{ action_raise_error("QUALITY must be between 1 (rough) and 5 (maximum). Use 3 (normal) if unsure.") }
	{% endif %}
	{% else %}
	{% set quality = default_quality %}
	{% endif %}
	{% if params2.FIRST_LAYER_DURATION is defined %}
	{% set first_layer_duration_mins = params2.FIRST_LAYER_DURATION|float %}
	{% if first_layer_duration_mins <= 0 %}
	{ action_raise_error("FIRST_LAYER_DURATION must be a positive number specifying the maximum first layer duration in minutes.") }
	{% endif %}
	{% if first_layer_duration_mins > 120 %}
	CONSOLE_ECHO MSG="FIRST_LAYER_DURATION will be limited to 120 minutes. Values larger than this will not have an effect on soak time."
	{% set first_layer_duration_mins = 120 %}
	{% endif %}
	{% set first_layer_duration_secs = (first_layer_duration_mins * 60.0)|int %}
	{% else %}
	{% set first_layer_duration_secs = default_first_layer_duration_secs %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	{% endif %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=True beacon_adaptive_heat_soak_layer_quality={quality} beacon_adaptive_heat_soak_maximum_first_layer_duration={first_layer_duration_secs}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."

[gcode_macro USE_FIXED_HEATSOAK]
description = Temporarily enables fixed bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
	Optionally specify DURATION (in minutes). Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.DURATION|default("0..720 minutes") %}
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_duration = (settings.variable_bed_heat_soak_time if defsrc == 'startup' else current.bed_heat_soak_time)|default(0)|int %}
	{% if params2.DURATION is defined %}
	{% set duration_mins = params2.DURATION|float %}
	{% if duration_mins < 0 %}
	{ action_raise_error("DURATION must be a non-negative number specifying the heatsoak duration in minutes.") }
	{% endif %}
	{% if duration_mins > 720 %}
	CONSOLE_ECHO MSG="DURATION will be limited to 720 minutes (12 hours). If you really need a larger value, adjust printer.cfg instead."
	{% set duration_mins = 720 %}
	{% endif %}
	{% set duration_secs = (duration_mins * 60.0)|int %}
	{% else %}
	{% set duration_secs = default_duration %}
	{% set duration_mins = duration_secs / 60.0 %}
	{% endif %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% if has_beacon %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=False bed_heat_soak_time={duration_secs}
	{% else %}
	HEATSOAK_SETTINGS QUIET=1 bed_heat_soak_time={duration_secs}
	{% endif %}
	{% if duration_mins < 1e-3 %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% else %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% endif %}

[gcode_macro USE_NO_HEATSOAK]
description = Temporarily disables bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
gcode = 
	USE_FIXED_HEATSOAK DURATION=0

[gcode_macro HEATSOAK_SETTINGS]
description = Shows or adjusts heatsoak settings
	- With no arguments: shows current heatsoak settings, specify VERBOSE=1 for detailed output
	- With arguments: sets the specified settings. Use the full setting name without the variable_ prefix, e.g. bed_heat_soak_time=300 or beacon_adaptive_heat_soak_layer_quality=4. See printer.cfg for available settings.
variable_default_source = "startup"
gcode = 
	
	{% set params2 = params %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% set quiet = params2.pop("QUIET", None)|default("0") in ("1", "true", "yes") %}
	{% set verbose = params2.pop("VERBOSE", None)|default("0") in ("1", "true", "yes") %}
	{% if has_beacon %}
	{% set vars = (
	"beacon_adaptive_heat_soak",
	"beacon_adaptive_heat_soak_max_wait",
	"beacon_adaptive_heat_soak_extra_wait_after_completion",
	"beacon_adaptive_heat_soak_layer_quality",
	"beacon_adaptive_heat_soak_maximum_first_layer_duration",
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% else %}
	{% set vars = (
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% endif %}
	{% set action = "show" if params|length == 0 else params2.ACTION %}
	{% if action is defined and params|length > 1 %}
	{ action_raise_error("ACTION cannot be specified with other parameters.") }
	{% elif action is not defined %}
	{% for k, v in params2.items() %}
	{% set k = k|lower %}
	{% if k in vars %}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Setting {k} to {v}"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={k} VALUE={v}
	{% else %}
	{ action_raise_error("Parameter '%s' is not recognised. Note that adaptive heatsoaking settings can only be set when a beacon probe is configured." % k) }
	{% endif %}
	{% endfor %}
	{% elif action == "reset" %}
	_RESET_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	CONSOLE_ECHO MSG="Heatsoak settings have been reset to their original values."
	{% elif action == "show" %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% set is_adaptive = False if not has_beacon else current.beacon_adaptive_heat_soak|default("")|lower == "true" %}
	{% if is_adaptive %}
	{% set quality = current.beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set first_layer_duration_secs = current.beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."
	{% elif current.bed_heat_soak_time|default(0)|int > 0 %}
	{% set duration_mins = (current.bed_heat_soak_time|int / 60.0) %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% else %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% endif %}
	{% if verbose %}
	CONSOLE_ECHO MSG="Detailed settings:"
	_SHOW_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	{% endif %}
	{% else %}
	{ action_raise_error("Action '%s' is not recognised" % action) }
	{% endif %}

[gcode_macro _LED_START_PRINTING]
gcode = 
	_LED_ACTION

[gcode_macro _LED_START_PRINTING_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_PRINTING]
gcode = 
	_LED_ON TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_PAUSE]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_ON]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_OFF]
gcode = 
	_LED_STANDBY

[gcode_macro _LED_LOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_LOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_RUNOUT]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_CLOG]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_UNLOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_UNLOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_DEACTIVATE_TOOLHEAD]
gcode = 
	_LED_OFF TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_STANDBY]
gcode = 
	_LED_STANDBY TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_WAKEUP]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_MOTORS_OFF]
gcode = 
	_LED_STANDBY
	_LED_VAOC_OFF

[gcode_macro _LED_INPUT_SHAPER_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_INPUT_SHAPER_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_BEACON_CALIBRATION_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_VAOC_ON]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=1.0 GREEN=1.0 BLUE=1.0
	{% endif %}

[gcode_macro _LED_VAOC_OFF]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=0.0 GREEN=0.0 BLUE=0.0
	{% endif %}

[gcode_macro _LED_ACTION]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_action %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SUCCESS]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_success %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_HEATING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_heating %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_COOLING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_cooling %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ERROR]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_error %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ON]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_on %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_OFF]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_off %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_STANDBY]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_standby %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}
	
	{% if toolhead >= 0 %}
	{% if printer['neopixel nozzle_led_t%s' % toolhead] is defined  %}
	SET_LED LED={'nozzle_led_t%s' % toolhead} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% else %}
	{% if printer['neopixel nozzle_led_t0'] is defined  %}
	SET_LED LED={'nozzle_led_t0'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% if printer['neopixel nozzle_led_t1'] is defined %}
	SET_LED LED={'nozzle_led_t1'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% endif %}
	
	_USER_LED_SET { rawparams }

[gcode_macro _USER_LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}

[gcode_macro LOAD_FILAMENT]
description = Loads new filament. Note: be careful with PETG, make sure you inspect the tip of your filament before loading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% if filament_name == '' or filament_type == '' %}
	{% set filament_name = 'unknown' %}
	{% set filament_type = 'unknown' %}
	{% endif %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_LOAD_FILAMENT TEMP={temp} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_LOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_LOAD_FILAMENT]
description = Load filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_LOAD_FILAMENT" MSG="TEMP={temp}"
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=load_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	_LOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	
	
	RESTORE_GCODE_STATE NAME=load_state
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament load routine complete, please check that the filament was loaded correctly."

[gcode_macro _IDEX_LOAD_FILAMENT]
description = Load filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament into T{toolhead}..."
	
	DEBUG_ECHO PREFIX="_IDEX_LOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	_LOAD_FILAMENT TOOLHEAD={toolhead} TEMP={temp} AUTOMATED={automated}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="Filament load routine for T{toolhead} complete, please check that the filament was loaded correctly."

[gcode_macro _LOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default(false)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE TOOLHEAD={toolhead}
	_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into hotend.."
	G92 E0
	G0 E{extruder_gear_to_cooling_position_distance} F{extruder_load_speed}
	G92 E0
	M400
	RATOS_ECHO MSG="Filament loaded into hotend."

[gcode_macro _LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set load_speed = printer["gcode_macro T%s" % toolhead].filament_load_speed|float * 60 %}
	{% set filament_loading_nozzle_offset = printer["gcode_macro T%s" % toolhead].filament_loading_nozzle_offset|float %}
	{% set cooling_position_to_nozzle_distance = printer["gcode_macro T%s" % toolhead].cooling_position_to_nozzle_distance|float %}
	{% set purge_after_load = printer["gcode_macro T%s" % toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into nozzle... Please wait!"
	G92 E0
	
	G0 E{cooling_position_to_nozzle_distance + filament_loading_nozzle_offset} F{load_speed}
	G92 E0
	G4 P1000
	_PURGE_FILAMENT	TOOLHEAD={toolhead} E={purge_after_load}
	RATOS_ECHO MSG="Filament loaded into nozzle!"

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"
	
	
	{% set filament_grabbing_length = printer["gcode_macro T%s" % toolhead].filament_grabbing_length|float %}
	{% set filament_grabbing_speed = printer["gcode_macro T%s" % toolhead].filament_grabbing_speed|float %}
	{% set resume_after_insert = true if printer["gcode_macro T%s" % toolhead].resume_after_insert|default(true)|lower == 'true' else false %}
	{% set enable_insert_detection = true if printer["gcode_macro T%s" % toolhead].enable_insert_detection|default(true)|lower == 'true' else false %}
	
	
	{% set current_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	
	{% if enable_insert_detection %}
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="toolhead: {toolhead}, filament_grabbing_length: {filament_grabbing_length}, filament_grabbing_speed: {filament_grabbing_speed}, current_idex_mode: {current_idex_mode}"
	
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	RATOS_ECHO MSG="Filament inserted into T{toolhead}, loading..."
	
	
	FORCE_MOVE STEPPER={'extruder%s' % ('' if toolhead == 0 else toolhead)} DISTANCE={filament_grabbing_length} VELOCITY={filament_grabbing_speed}
	M400
	
	
	{% if printer.pause_resume.is_paused %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% if resume_after_insert %}
	RESUME
	{% endif %}
	{% else %}
	{% if not printer.virtual_sdcard.is_active %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"

[gcode_macro _PURGE_BEFORE_UNLOAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set purge_before_unload = printer["gcode_macro T%s" % toolhead].purge_before_unload|float %}
	
	DEBUG_ECHO PREFIX="_PURGE_BEFORE_UNLOAD" MSG="TOOLHEAD: {toolhead}"
	
	
	{% if purge_before_unload > 0 %}
	G92 E0
	G0 E{purge_before_unload} F300
	G92 E0
	M400
	{% endif %}

[gcode_macro _PURGE_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set e = params.E|int %}
	{% set r = params.R|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_PURGE_FILAMENT" MSG="TOOLHEAD: {toolhead}, E: {e}"
	
	
	{% if e > 0 %}
	
	
	G92 E0
	G0 E{e} F300
	G92 E0
	M400
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={0.4 if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={0.4 if toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * 0.4)}
	{% endif %}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if r > 0 %}
	G92 E0
	G0 E-{r} F300
	G92 E0
	M400
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro _MOVE_TO_LOADING_POSITION]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_MOVE_TO_LOADING_POSITION" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	
	G1 X{loading_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _CLEANING_MOVE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_CLEANING_MOVE" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].parking_position is defined and printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set parking_position = printer["gcode_macro T%s" % toolhead].parking_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	{% set cleaning_position = loading_position %}
	{% if loading_position == parking_position %}
	{% if loading_position > 0 %}
	{% set cleaning_position = loading_position - 30 %}
	{% else %}
	{% set cleaning_position = loading_position + 30 %}
	{% endif %}
	{% endif %}
	
	
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _BED_MESH_SANITY_CHECK]
gcode = 
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is defined %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_start_print_true_zero_fuzzy_position %}
	CONSOLE_ECHO TYPE="error" TITLE="Defined zero reference not compatible with fuzzy true zero" MSG="Using fuzzy start print true zero position is not compatible with a defined zero_reference_position value in the [bed_mesh] section in printer.cfg._N_Please remove the zero_reference_position value from the [bed_mesh] section, or disable fuzzy true zero position in printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_start_print_true_zero_fuzzy_position: False"
	_STOP_AND_RAISE_ERROR MSG="Defined zero reference not compatible with fuzzy true zero"
	{% elif zero_ref_pos[0]|float|round != safe_home_x|float|round or zero_ref_pos[1]|float|round != safe_home_y|float|round %}
	CONSOLE_ECHO TYPE="error" TITLE="Zero reference position does not match safe home position" MSG="Please update your bed mesh zero reference position in printer.cfg, like so:_N__N_[bed_mesh]_N_zero_reference_position: {safe_home_x|float|round},{safe_home_y|float|round}_N_"
	_STOP_AND_RAISE_ERROR MSG="Zero reference position does not match safe home position"
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_bed_mesh %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact bed mesh is enabled" MSG="Beacon contact bed mesh is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_bed_mesh: False"
	{% endif %}
	
	{% if beacon_scan_method_automatic %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon 'automatic' scan method is enabled" MSG="Beacon 'automatic' scan method is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_scan_method_automatic: False"
	{% endif %}
	
	{% if beacon_contact_z_tilt_adjust %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact z-tilt adjust is enabled" MSG="Beacon contact z-tilt adjust is enabled. This is not recommended for normal use and may result in inaccurate z-tilt adjustment._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_z_tilt_adjust: False"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH]
gcode = 
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE=None
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE=None
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION {rawparams}
	{% endif %}

[gcode_macro _START_PRINT_BED_MESH]
variable_actual_true_zero_position_x = None
variable_actual_true_zero_position_y = None
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set X=[params.X0|default(-1)|float, params.X1|default(-1)|float] %}
	{% set Y=[params.Y0|default(-1)|float, params.Y1|default(-1)|float] %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_BED_MESH" MSG="idex_mode: {idex_mode}, X: {X}, Y: {Y}"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is not defined %}
	{% set zero_ref_pos = [safe_home_x if actual_true_zero_position_x is none else actual_true_zero_position_x, safe_home_y if actual_true_zero_position_y is none else actual_true_zero_position_y] %}
	{% endif %}
	
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	
	
	
	
	{% set X=[0, printable_x_max] %}
	{% endif %}
	
	
	{% set beacon_bed_mesh_scv = printer["gcode_macro RatOS"].beacon_bed_mesh_scv|default(25)|int %}
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% if printer.fastconfig.settings.beacon is defined and not beacon_contact_bed_mesh %}
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={beacon_bed_mesh_scv}
	{% endif %}
	
	
	{% set default_profile = printer["gcode_macro RatOS"].bed_mesh_profile|default('ratos') %}
	{% if printer["gcode_macro RatOS"].calibrate_bed_mesh|lower == 'true' %}
	BED_MESH_CLEAR
	{% if printer["gcode_macro RatOS"].adaptive_mesh|lower == 'true' %}
	CALIBRATE_ADAPTIVE_MESH PROFILE="{default_profile}" X0={X[0]} X1={X[1]} Y0={Y[0]} Y1={Y[1]} T={params.T|int} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={idex_mode} ZERO_REF_POS_X={zero_ref_pos[0]} ZERO_REF_POS_Y={zero_ref_pos[1]}
	{% else %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	BED_MESH_PROFILE LOAD="{default_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	
	{% elif printer["gcode_macro RatOS"].bed_mesh_profile is defined %}
	BED_MESH_CLEAR
	BED_MESH_PROFILE LOAD="{printer["gcode_macro RatOS"].bed_mesh_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"

[gcode_macro CALIBRATE_ADAPTIVE_MESH]
gcode = 
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set default_profile = params.PROFILE %}
	
	
	{% set x0 = params.X0|default(-1)|float %}
	{% set y0 = params.Y0|default(-1)|float %}
	{% set x1 = params.X1|default(-1)|float %}
	{% set y1 = params.Y1|default(-1)|float %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Received coordinates X0={x0|round(1)} Y0={y0|round(1)} X1={x1|round(1)} Y1={y1|round(1)}"
	
	{% if x0 >= x1 or y0 >= y1 %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Invalid coordinates received. Please check your slicer settings. Falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	
	
	{% if params.ZERO_REF_POS_X is defined and params.ZERO_REF_POS_Y is defined %}
	{% set zero_ref_pos_x = params.ZERO_REF_POS_X|float %}
	{% set zero_ref_pos_y = params.ZERO_REF_POS_Y|float %}
	{% if zero_ref_pos_x < x0 or zero_ref_pos_x > x1 or zero_ref_pos_y < y0 or zero_ref_pos_y > y1 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Zero reference position X={zero_ref_pos_x|round(1)} Y={zero_ref_pos_y|round(1)} is outside the mesh region, expanding mesh region to include it."
	{% set x0 = [x0, zero_ref_pos_x]|min %}
	{% set y0 = [y0, zero_ref_pos_y]|min %}
	{% set x1 = [x1, zero_ref_pos_x]|max %}
	{% set y1 = [y1, zero_ref_pos_y]|max %}
	{% endif %}
	{% endif %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float %}
	
	
	{% set mesh_x0 = [[x0, max_x]|min, min_x]|max %}
	{% set mesh_y0 = [[y0, max_y]|min, min_y]|max %}
	{% set mesh_x1 = [[x1, max_x]|min, min_x]|max %}
	{% set mesh_y1 = [[y1, max_y]|min, min_y]|max %}
	
	{% if mesh_x0 == min_x and mesh_y0 == min_y and mesh_x1 == max_x and mesh_y1 == max_y %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Print is using the full bed, falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	
	{% set probe_count_x = mesh_config.probe_count.split(",")[0]|int %}
	{% if mesh_config.probe_count.split(",")|length == 2 %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[1]|int %}
	{% else %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[0]|int %}
	{% endif %}
	
	
	{% set probe_x_step = (max_x - min_x) / probe_count_x %}
	{% set probe_y_step = (max_y - min_y) / probe_count_y %}
	
	
	{% set mesh_count_x = ([(mesh_x1 - mesh_x0) / probe_x_step, 3]|max)|int %}
	{% set mesh_count_y = ([(mesh_y1 - mesh_y0) / probe_y_step, 3]|max)|int %}
	{% set min_mesh_count = [mesh_count_x, mesh_count_y]|min %}
	{% set max_mesh_count = [mesh_count_x, mesh_count_y]|max %}
	
	
	{% set algorithm = mesh_config.algorithm %}
	{% if algorithm|lower == 'lagrange' and max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="cannot exceed a probe_count of 6 when using lagrange interpolation. Falling back to bicubic interpolation."
	{% set algorithm = 'bicubic' %}
	{% endif %}
	{% if algorithm|lower == 'bicubic' and min_mesh_count < 4 %}
	{% if max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="invalid probe_count option when using bicubic interpolation. Combination of 3 points on one axis with more than 6 on another is not permitted. Forcing minimum mesh count to be 4."
	{% set min_mesh_count = 4 %}
	{% else %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="bicubic interpolation with a probe_count of less than 4 points detected. Forcing lagrange interpolation."
	{% set algorithm = 'lagrange' %}
	{% endif %}
	{% endif %}
	
	{% set mesh_count_x = ([min_mesh_count, mesh_count_x]|max)|int %}
	{% set mesh_count_x = ([max_mesh_count, mesh_count_x]|min)|int %}
	{% set mesh_count_y = ([min_mesh_count, mesh_count_y]|max)|int %}
	{% set mesh_count_y = ([max_mesh_count, mesh_count_y]|min)|int %}
	
	{% set should_prime = printer["gcode_macro RatOS"].nozzle_priming == 'primeblob' %}
	{% if printer["dual_carriage"] is not defined %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% else %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 != 0 and probe_first %}
	{% set probe_first = false %}
	{% elif printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 == 0 and not probe_first %}
	{% set probe_first = true %}
	{% endif %}
	
	
	{% if should_prime and probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="mesh coordinates X0={mesh_x0|round(1)} Y0={mesh_y0|round(1)} X1={mesh_x1|round(1)} Y1={mesh_y1|round(1)}"
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y} RELATIVE_REFERENCE_INDEX=-1
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	
	
	{% if should_prime and not probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro M84]
rename_existing = M84.1
gcode = 
	
	M84.1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_OFFSET X=0 Y=0
	
	
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro _VAOC"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False
	{% endif %}
	
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	SET_SKEW CLEAR=1
	
	
	_LED_MOTORS_OFF

[gcode_macro M104]
rename_existing = M104.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M104" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set temperature_offset_t0 = printer["gcode_macro T0"].temperature_offset|default(0)|int %}
	{% set temperature_offset_t1 = printer["gcode_macro T1"].temperature_offset|default(0)|int %}
	{% set s0 = [s + temperature_offset_t0, 0]|max %}
	{% set s1 = [s + temperature_offset_t1, 0]|max %}
	{% if temperature_offset_t0 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t0}°C added to toolhead T0."
	{% endif %}
	{% if temperature_offset_t1 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t1}°C added to toolhead T1."
	{% endif %}
	{% else %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	M104.1 S{s0} T0
	M104.1 S{s1} T1
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% else %}
	M104.1 S{s} T{t}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M109]
rename_existing = M109.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M109" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M109" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	M109.1 S{s} T{t}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro SET_HEATER_TEMPERATURE]
rename_existing = SET_HEATER_TEMPERATURE_BASE
gcode = 
	
	{% set heater = params.HEATER|default("") %}
	{% set target = params.TARGET|default(0)|int %}
	
	DEBUG_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="heater: {heater}, target: {target}"
	
	{% set t = -1 %}
	{% if heater|lower == "extruder" or heater|lower == "extruder1" %}
	
	{% set t = 0 if heater|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and target > 0 %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set target = [target + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE_BASE HEATER="{heater}" TARGET={target}
	
	{% if t != -1 and printer.fastconfig.settings.beacon is defined %}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro TEMPERATURE_WAIT]
rename_existing = TEMPERATURE_WAIT_BASE
gcode = 
	
	{% set sensor = params.SENSOR|default("") %}
	{% set minimum = params.MINIMUM|default(-1)|int %}
	{% set maximum = params.MAXIMUM|default(-1)|int %}
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="sensor: {sensor}, minimum: {minimum}, maximum: {maximum}"
	
	{% set t = -1 %}
	{% if sensor|lower == "extruder" or sensor|lower == "extruder1" %}
	
	{% set t = 0 if sensor|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and (minimum > 0 or maximum > 0) %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% if minimum > -1 %}
	{% set minimum = [minimum + temperature_offset, 0]|max %}
	{% endif %}
	{% if maximum > -1 %}
	{% set maximum = [maximum + temperature_offset, 0]|max %}
	{% endif %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set id = "sensor " ~ sensor if t == -1 else "toolhead T" ~ t %}
	
	
	{% if minimum > -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum} MAXIMUM={maximum}
	{% elif minimum > -1 and maximum == -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum}
	{% elif minimum == -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MAXIMUM={maximum}
	{% else %}
	
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="neither MINIMUM or MAXIMUM args were specified, call TEMPERATURE_WAIT_BASE is expected to fail"
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}"
	{% endif %}
	
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature for {id} reached."

[gcode_macro SDCARD_PRINT_FILE]
rename_existing = SDCARD_PRINT_FILE_BASE
gcode = 
	{% if printer["ratos"] is defined %}
	PROCESS_GCODE_FILE { rawparams }
	{% else %}
	SDCARD_PRINT_FILE_BASE { rawparams }
	{% endif %}

[gcode_macro SKEW_PROFILE]
rename_existing = SKEW_PROFILE_BASE
variable_loaded_profile = ""
gcode = 
	{% if params.LOAD is defined %}
	{% if printer.fastconfig.settings["skew_correction %s" % params.LOAD] is defined %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='"{params.LOAD}"'
	{% endif %}
	{% endif %}
	
	SKEW_PROFILE_BASE { rawparams }

[gcode_macro SET_SKEW]
rename_existing = SET_SKEW_BASE
gcode = 
	{% if params.CLEAR is defined %}
	{% if params.CLEAR|default(0)|int == 1 %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='""'
	{% endif %}
	{% endif %}
	
	SET_SKEW_BASE { rawparams }

[gcode_macro SET_VELOCITY_LIMIT]
rename_existing = SET_VELOCITY_LIMIT_BASE
gcode = 
	{% if params.ACCEL_TO_DECEL is defined %}
	
	{% if params.ACCEL is defined %}
	{% set accel = params.ACCEL|float %}
	{% else %}
	{% set accel = printer.toolhead.max_accel|float %}
	{% endif %}
	
	{% if params.VELOCITY is defined %}
	{% set velocity = params.VELOCITY|float %}
	{% else %}
	{% set velocity = printer.toolhead.max_velocity|float %}
	{% endif %}
	
	{% if params.SQUARE_CORNER_VELOCITY is defined %}
	{% set scv = params.SQUARE_CORNER_VELOCITY|float %}
	{% else %}
	{% set scv = printer.toolhead.square_corner_velocity|float %}
	{% endif %}
	
	{% set mcr = params.ACCEL_TO_DECEL|float / accel %}
	
	DEBUG_ECHO PREFIX="SET_VELOCITY_LIMIT" MSG="ACCEL={accel}, VELOCITY={velocity}, SQUARE_CORNER_VELOCITY={scv}, MINIMUM_CRUISE_RATIO={mcr}"
	
	SET_VELOCITY_LIMIT_BASE ACCEL={accel} VELOCITY={velocity} SQUARE_CORNER_VELOCITY={scv} MINIMUM_CRUISE_RATIO={1-mcr}
	
	{% else %}
	
	SET_VELOCITY_LIMIT_BASE { rawparams }
	
	{% endif %}

[gcode_macro BED_MESH_CALIBRATE]
rename_existing = _BED_MESH_CALIBRATE_BASE
variable_abl_and_home_z_if_required = True
gcode = 
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	{% if abl_and_home_z_if_required %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% endif %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set beacon_default_probe_method = printer.fastconfig.settings.beacon.default_probe_method|default('proximity') %}
	{% set probe_method = params.PROBE_METHOD|default(beacon_default_probe_method)|lower %}
	{% if probe_method == 'proximity' %}
	_CHECK_ACTIVE_BEACON_MODEL_TEMP TITLE="Bed mesh calibration warning"
	{% endif %}
	{% endif %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_BED_MESH_CALIBRATE_BASE {rawparams}
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	_APPLY_RATOS_BED_MESH_PARAMETERS {rawparams}
	{% endif %}

[gcode_macro SET_GCODE_OFFSET]
rename_existing = SET_GCODE_OFFSET_BASE
gcode = 
	DEBUG_ECHO PREFIX="SET_GCODE_OFFSET" MSG="{rawparams|replace('"', '')|replace("'", '')}"
	{% set z_before = printer.gcode_move.homing_origin.z|float %}
	SET_GCODE_OFFSET_BASE {rawparams}
	_AFTER_SET_GCODE_OFFSET Z_BEFORE={z_before}

[gcode_macro _AFTER_SET_GCODE_OFFSET]
gcode = 
	{% set z_before = params.Z_BEFORE|float %}
	{% set z_after = printer.gcode_move.homing_origin.z|float %}
	{% if z_before != z_after %}
	_ALERT_NON_ZERO_Z_OFFSET FORCE=1
	{% endif %}

[gcode_macro _START_PRINT_PARK]
gcode = 
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_x = printer["gcode_macro RatOS"].start_print_park_x %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% if printer["gcode_macro RatOS"].start_print_park_x is defined and printer["gcode_macro RatOS"].start_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="start_print_park_x is ignored for IDEX printers"
	{% endif %}
	PARK_TOOLHEAD
	G90
	{% endif %}
	
	
	_PARK LOCATION={start_print_park_in} X={start_print_park_x}
	G0 Z{z} F{z_speed}

[gcode_macro _END_PRINT_PARK]
gcode = 
	{% if printer["dual_carriage"] is defined %}
	
	{% if printer["gcode_macro RatOS"].end_print_park_x is defined and printer["gcode_macro RatOS"].end_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="end_print_park_x is ignored for IDEX printers"
	{% endif %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	PARK_TOOLHEAD
	G90
	{% endif %}
	_PARK LOCATION={printer["gcode_macro RatOS"].end_print_park_in} X={printer["gcode_macro RatOS"].end_print_park_x}

[gcode_macro _PARK]
gcode = 
	
	{% set x = params.X %}
	{% set location = params.LOCATION|default('back')|lower %}
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	{% set nozzle_priming = printer["gcode_macro RatOS"].nozzle_priming|lower %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="park"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% if x != '' %}
	{% if x|float >= printer.toolhead.axis_minimum.x + 5 and x|float <= printable_x_max - 5 %}
	{% set park_x = x|float %}
	{% else %}
	{action_respond_info('The requested X co-ordinate is outside the defined axis bounds - using defaults')}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	{% else %}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	
	
	{% set park_y = printable_y_max - 15 %}
	{% if location == 'front' %}
	{% set park_y = printer.toolhead.axis_minimum.y + 5 %}
	{% elif location == 'center' %}
	{% set park_y = printable_y_max / 2 %}
	{% elif location == 'primeblob' and printer["dual_carriage"] is defined %}
	
	{% set park_y = printable_y_max - 15 %}
	{% endif %}
	
	
	{% if location == 'primeblob' and printer["dual_carriage"] is not defined %}
	{% if (nozzle_priming == 'primeblob' or nozzle_priming == 'primeline') %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set park_x = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set park_x = printable_x_max - 5 %}
	{% else %}
	{% set park_x = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set park_y = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set park_y = printable_y_max - 5 %}
	{% else %}
	{% set park_y = nozzle_prime_start_y|float %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	G0 X{park_x} Y{park_y} F{speed}
	{% else %}
	
	G0 Y{park_y} F{speed}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="park"

[gcode_macro SAVE_PROBE_RESULT]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	{% set last_z_offset = 9999.9 %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if beacon_contact_prime_probing %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	{% else %}
	{% set last_z_offset = printer.beacon.last_sample.dist - current_z %}
	{% endif %}
	{% elif printer.fastconfig.settings.bltouch is defined  %}
	{% set config_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% elif printer.fastconfig.settings.probe is defined  %}
	{% set config_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% endif %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Saving offset adjustment of {last_z_offset} in {params.VARIABLE|default('last_z_offset')}"
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={params.VARIABLE|default('last_z_offset')} VALUE={last_z_offset}

[gcode_macro PROBE_FOR_PRIMING]
gcode = 
	
	{% set probe_for_priming_disable_mesh_constraints = true if printer["gcode_macro RatOS"].probe_for_priming_disable_mesh_constraints|default(false)|lower == 'true' else false %}
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower != 'false' %}
	SAVE_GCODE_STATE NAME=probe_for_priming_state
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the prime location.."
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set t = params.TOOLHEAD|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% if idex_mode == '' %}
	
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% if t == 0 %}
	{% set x_start = 5 %}
	{% else %}
	{% set x_start = printable_x_max - 5 %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% endif %}
	{% endif %}
	{% set z = printer.fastconfig.settings.bed_mesh.horizontal_move_z|float %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% if printer.fastconfig.settings.bltouch is defined %}
	{% set x_offset = printer.fastconfig.settings.bltouch.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.bltouch.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% elif printer.fastconfig.settings.probe is defined %}
	{% set x_offset = printer.fastconfig.settings.probe.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.probe.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% elif printer.fastconfig.settings.beacon is defined %}
	{% set x_offset = printer.fastconfig.settings.beacon.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.beacon.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.beacon.trigger_distance|float %}
	{% else %}
	{ action_raise_error("No probe, beacon or bltouch section found. Adaptive priming only works with a [probe], [beacon] or [bltouch] section defined.") }
	{% endif %}
	
	{% if z < z_offset %}
	{ action_raise_error("Horizontal move Z ({z}) is below your probe's Z offset ({z_offset}). Please adjust your horizontal_move_z setting in [bed_mesh] to be above {z}.") }
	{% endif %}
	
	{% if not probe_for_priming_disable_mesh_constraints %}
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float - x_offset %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float - y_offset %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float - x_offset %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float - y_offset %}
	
	
	{% set x_start = [[x_start, max_x]|min, min_x]|max %}
	{% set y_start = [[y_start, max_y]|min, min_y]|max %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the start of the prime location at {x_start}, {y_start}"
	
	G90
	
	M83
	
	G0 Z{z} F{z_speed}
	
	G1 X{x_start} Y{y_start} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result
	{% endif %}
	
	{% if idex_mode == '' %}
	
	{% set x_end = x_start %}
	{% set y_end = y_start + 45 %}
	{% else %}
	
	{% if t==1 %}
	{% set x_end = x_start - 45 %}
	{% else %}
	{% set x_end = x_start + 45 %}
	{% endif %}
	{% set y_end = y_start %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the end of the prime location at {x_end}, {y_end}"
	G1 X{x_end} Y{y_end} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result
	{% endif %}
	
	RESTORE_GCODE_STATE NAME=probe_for_priming_state
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	{% endif %}

[gcode_macro RESET_PRIME_PROBE_STATE]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result VALUE=None
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result_t1 VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result_t1 VALUE=None
	{% endif %}

[gcode_macro PROBE_CURRENT_POSITION]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	SAVE_GCODE_STATE NAME=probe_current_position_state
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	ASSERT_PROBE_DEPLOYED
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_prime_probing %}
	PROBE PROBE_METHOD=contact SAMPLES=1
	{% else %}
	PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	BEACON_QUERY
	{% else %}
	
	RESTORE_GCODE_STATE NAME=probe_current_position_state MOVE=1 MOVE_SPEED={printer["gcode_macro RatOS"].macro_z_speed|float}
	{% endif %}

[gcode_macro PRIME_BLOB]
description = Prints a primeblob, used internally, if configured, as part of the START_PRINT macro.
variable_x_offset = 5
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="prime_blob"
	SET_MACRO_TRAVEL_SETTINGS
	
	RATOS_ECHO PREFIX="Priming" MSG="Priming nozzle with prime blob.."
	
	
	{% set current_toolhead = 0 %}
	
	
	{% set target_idex_mode = '' %}
	{% set extruder = 'extruder' %}
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE is defined %}
	{% set target_idex_mode = params.IDEX_MODE|default('')|lower %}
	{% else %}
	{ action_raise_error("IDEX_MODE parameter not found for PRIME_BLOB macro. This is likely a bug.") }
	{% endif %}
	RATOS_ECHO PREFIX="Priming" MSG="Priming in IDEX {target_idex_mode} mode.."
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set current_toolhead = 1 if current_idex_mode=='primary' else 0 %}
	{% set extruder = 'extruder1' if current_toolhead == 1 else 'extruder' %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	SAVE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set fan_speed = printer["gcode_macro RatOS"].nozzle_prime_bridge_fan|float %}
	{% set nozzle_diameter = printer.fastconfig.settings[extruder].nozzle_diameter|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set has_start_offset_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) != 9999.9 %}
	{% if printer["dual_carriage"] is defined %}
	{% set has_start_offset_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) != 9999.9 %}
	{% endif %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_z_height = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set nozzle_prime_direction = printer["gcode_macro RatOS"].nozzle_prime_direction|lower %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% if target_idex_mode == '' %}
	
	{% set x_factor = 0 %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% set y_factor = -1 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% if nozzle_prime_start_y|float < printable_y_max / 2 %}
	{% set y_factor = 1 %}
	{% else %}
	{% set y_factor = -1 %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_direction == 'forwards' %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_direction == 'backwards' %}
	{% set y_factor = -1 %}
	{% endif %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% else %}
	{% set z = start_print_park_z_height %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% set y_factor = 0 %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set x_start = center_x / 2 + 5 %}
	{% set x_factor = 1 %}
	{% else %}
	
	
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% if current_toolhead == 0 %}
	{% set x_start = 55 %}
	{% set x_factor = -1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 55 %}
	{% set x_factor = 1 %}
	{% endif %}
	{% else %}
	{% if current_toolhead == 0 %}
	{% set x_start = 5 %}
	{% set x_factor = 1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 5 %}
	{% set x_factor = -1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_x_max - 5 %}
	{% endif %}
	{% set z = 10 %}
	{% endif %}
	
	{% set start_z_offset = 0 %}
	{% set end_z_offset = 0 %}
	{% if has_start_offset_t0 %}
	{% set start_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) %}
	{% set end_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_end_result|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t0) ) }
	{% endif %}
	{% if end_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t0) )  }
	{% endif %}
	{% set start_z_offset = start_z_probe_result_t0 %}
	{% set end_z_offset = end_z_probe_result_t0 %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	{% if current_toolhead == 1 or both_toolheads or target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	{% if has_start_offset_t1 %}
	{% set start_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) %}
	{% set end_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_end_result_t1|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t1) ) }
	{% endif %}
	{% if end_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t1) ) }
	{% endif %}
	{% set start_z_offset = [start_z_offset, start_z_probe_result_t1]|max %}
	{% set end_z_offset = [end_z_offset, start_z_probe_result_t1]|max %}
	{% endif %}
	{% endif %}
	{% if target_idex_mode != 'copy' and target_idex_mode != 'mirror' %}
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% set original_start_z_offset = start_z_offset %}
	{% set original_end_z_offset = end_z_offset %}
	{% set start_z_offset = original_end_z_offset %}
	{% set end_z_offset = original_start_z_offset %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	DEBUG_ECHO PREFIX="PRIME_BLOB" MSG="x_start: {x_start}, y_start: {y_start}, x_factor: {x_factor}, y_factor: {y_factor}, z: {z}, start_z_offset: {start_z_offset}, end_z_offset: {end_z_offset}"
	
	
	G90
	
	M83
	RATOS_ECHO PREFIX="Priming" MSG="Lifting Z to {z}.."
	
	G0 Z{z} F{z_speed}
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% if start_print_park_in != 'primeblob' %}
	G1 X{x_start} F{speed}
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% endif %}
	{% else %}
	
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% if target_idex_mode=="copy" or target_idex_mode=="mirror" %}
	RATOS_ECHO PREFIX="Priming" MSG="Mirroring move to {x_start}, {y_start} along the edge of the print area.."
	
	_IDEX_MIRROR PRIMING=1
	{% else %}
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% endif %}
	G1 X{x_start} F{speed}
	{% endif %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Starting prime blob.."
	
	G1 Z{0.5 + start_z_offset} F{z_speed}
	
	G1 Y{y_start} F{speed}
	
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	
	M106 S{fan_speed}
	
	G1 Z5 F100 E5
	G92 E0
	RATOS_ECHO PREFIX="Priming" MSG="Bridging with {((fan_speed/255) * 100)|int}% fan speed.."
	
	G1 F3000 X{x_start + (15 * x_factor)} Y{y_start + (15 * y_factor)} E{1 / ((0.4 / nozzle_diameter) ** 2)}
	
	
	
	G1 F3000 X{x_start + (20 * x_factor)} Y{y_start + (20 * y_factor)} Z{3.8 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (34 * x_factor)} Y{y_start + (34 * y_factor)} Z{2.6 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (38 * x_factor)} Y{y_start + (38 * y_factor)} Z{1.4 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (42 * x_factor)} Y{y_start + (42 * y_factor)} Z{0.2 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	
	M106 S0
	
	G1 F3000 X{x_start + (46 * x_factor)} Y{y_start + (46 * y_factor)} Z{0.2 + end_z_offset} E0.6
	
	G1 F{speed} X{x_start + (50 * x_factor)} Y{y_start + (50 * y_factor)}
	
	
	{% if target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if target_idex_mode == "copy" %}
	{% if first_y >= 0 %}
	_IDEX_COPY DANCE=0 Y={first_y}
	{% else %}
	_IDEX_COPY DANCE=0 Y={params.Y1}
	{% endif %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	RESTORE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="prime_blob"
	
	
	G92 E0

[gcode_macro UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set temp = params.TEMP|default(220)|int %}
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_UNLOAD_FILAMENT TEMP={temp} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_UNLOAD_FILAMENT]
description = Unload filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_UNLOAD_FILAMENT" MSG="TEMP: {temp}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=unload_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	G4 P3000
	
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD=0 NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=unload_state
	
	
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament unloading completed"

[gcode_macro _IDEX_UNLOAD_FILAMENT]
description = Unload filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading T{toolhead} filament..."
	
	DEBUG_ECHO PREFIX="_IDEX_UNLOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} AUTOMATED={automated}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="T{toolhead} filament unloading completed"

[gcode_macro _UNLOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LEGACY_UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
gcode = 
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set unload_speed = 5 * 60 %}
	{% set unload_length = printer["gcode_macro RatOS"].filament_unload_length|float %}
	M117 Unloading filament...
	
	G0 E10 F300
	
	G0 E-5 F3600
	
	G4 P3000
	
	G0 E5 F6000
	
	G0 E-15 F6000
	
	G0 E-{unload_length} F{unload_speed}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}
	M117 Filament unloaded!
	RESPOND MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	RATOS_ECHO MSG="Unloading filament from nozzle to cooling zone... Please wait!"
	
	_PURGE_BEFORE_UNLOAD TOOLHEAD={toolhead}
	
	{% if printer["gcode_macro _UNLOAD_WITHOUT_TIP_FORMING"] is defined %}
	
	_UNLOAD_WITHOUT_TIP_FORMING TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	_UNLOAD_WITH_TIP_FORMING NAME='{filament_name}' TYPE='{filament_type}'
	{% endif %}
	
	G4 P3000

[gcode_macro _UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	{% set tooolhead_sensor_to_extruder_gear_distance = printer["gcode_macro T%s" % toolhead].tooolhead_sensor_to_extruder_gear_distance|float %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER" MSG="TOOLHEAD: {toolhead}"
	
	
	G0 E-{extruder_gear_to_cooling_position_distance + tooolhead_sensor_to_extruder_gear_distance + 50} F{extruder_load_speed}
	
	RATOS_ECHO MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_WITH_TIP_FORMING]
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	{% if filament_name != '' and filament_type != '' %}
	_UNLOAD_KNOWN_FILAMENT NAME={filament_name} TYPE={filament_type}
	{% else %}
	_UNLOAD_UNKNOWN_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _UNLOAD_KNOWN_FILAMENT]
description = User overrideable tip forming macro if slicer filament profiles are known
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	RATOS_ECHO PREFIX="FILAMENT TYPE" MSG='{filament_type}'
	RATOS_ECHO PREFIX="FILAMENT PROFILE" MSG='{filament_name}'
	
	
	{% if filament_name == "Prusament PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% elif filament_name == "Nobufil PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% else %}
	
	RATOS_ECHO PREFIX="_UNLOAD_KNOWN_FILAMENT" MSG="Filament profile not found!"
	_UNLOAD_UNKNOWN_FILAMENT
	{% endif %}

[gcode_macro _UNLOAD_UNKNOWN_FILAMENT]
description = User overrideable standard tip forming macro
gcode = 
	
	DEBUG_ECHO PREFIX="_UNLOAD_UNKNOWN_FILAMENT" MSG="Using standard tip forming macro!"
	
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10

[gcode_macro _TIP_FORMING]
gcode = 
	
	{% set cooling_moves = params.COOLING_MOVES|default(4)|int %}
	{% set cooling_move_length = params.COOLING_MOVE_LENGTH|default(10)|float %}
	{% set start_cooling_speed = params.START_COOLING_SPEED|default(10)|float * 60 %}
	{% set end_cooling_speed = params.END_COOLING_SPEED|default(50)|float * 60 %}
	{% if cooling_moves == 0 %}
	{% set cooling_move_length = 0 %}
	{% endif %}
	
	
	{% set dip = true if params.DIP|default(false)|lower == "true" else false %}
	{% set dip_length = params.DIP_LENGTH|default(22)|float %}
	{% set dip_speed = params.DIP_SPEED|default(30)|float * 60 %}
	{% set dip_retract_speed = params.DIP_RETRACT_SPEED|default(70)|float * 60 %}
	
	
	{% set retract_length = params.RETRACT_LENGTH|default(18)|float %}
	{% set start_retract_speed = params.START_RETRACT_SPEED|default(120)|float * 60 %}
	{% set end_retract_speed = params.END_RETRACT_SPEED|default(20)|float * 60 %}
	
	DEBUG_ECHO PREFIX="_TIP_FORMING" MSG="cooling_moves: {cooling_moves}, cooling_move_length: {cooling_move_length}, start_cooling_speed: {start_cooling_speed}, end_cooling_speed: {end_cooling_speed}, dip: {dip}, dip_length: {dip_length}, dip_speed: {dip_speed}, dip_retract_speed: {dip_retract_speed}, retract_length: {retract_length}, start_retract_speed: {start_retract_speed}, end_retract_speed: {end_retract_speed}"
	
	M220 S100
	
	
	G92 E0
	{% set retract = retract_length + cooling_move_length / 2 - 15 %}
	G1 E-15 F{start_retract_speed}
	G1 E-{0.7 * retract} F{1.0 * end_retract_speed}
	G1 E-{0.2 * retract} F{0.5 * end_retract_speed}
	G1 E-{0.1 * retract} F{0.3 * end_retract_speed}
	
	
	G92 E0
	{% if cooling_moves > 0 %}
	{% set i = (end_cooling_speed - start_cooling_speed) / (2 * cooling_moves - 1) %}
	{% for m in range(cooling_moves) %}
	G1 E{cooling_move_length} F{(start_cooling_speed + i * m * 2)}
	G1 E-{cooling_move_length} F{(start_cooling_speed + i * (m * 2 + 1))}
	{% endfor %}
	{% endif %}
	
	
	G92 E0
	{% if dip %}
	G1 E{dip_length} F{dip_speed}
	G4 P100
	G1 E-{dip_length} F{dip_retract_speed}
	{% endif %}
	
	G92 E0
	M400

[delayed_gcode __ON_FILAMENT_SENSOR_BUTTON_PRESSED_STARTUP_GUARD]
initial_duration = 2.
gcode = 
	SET_GCODE_VARIABLE MACRO=_ON_FILAMENT_SENSOR_BUTTON_PRESSED VARIABLE=startup_complete VALUE=True

[gcode_macro _ON_FILAMENT_SENSOR_BUTTON_PRESSED]
variable_startup_complete = False
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set toolhead_sensor_button_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_sensor_button_only_when_sensor_enabled|default(false)|lower == 'true' %}
	
	
	{% if not startup_complete and sensor_enabled %}
	{action_emergency_stop("RatOS: The T%s filament sensor button was triggered immediately on printer startup. This is likely a false trigger. Please check your filament sensor wiring and configuration!" % (toolhead,))}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_SENSOR_BUTTON_PRESSED" MSG="TOOLHEAD: {toolhead}, SENSOR_ENABLED: {sensor_enabled}, TOOLHEAD_SENSOR_BUTTON_ONLY_WHEN_SENSOR_ENABLED: {toolhead_sensor_button_only_when_sensor_enabled}"
	
	{% if not printer.virtual_sdcard.is_active and (sensor_enabled or not toolhead_sensor_button_only_when_sensor_enabled) %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	{% set toolhead_detect_clog_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_detect_clog_only_when_sensor_enabled|default(true)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}, ENABLE_CLOG_DETECTION: {enable_clog_detection}, TOOLHEAD_DETECT_CLOG_ONLY_WHEN_SENSOR_ENABLED: {toolhead_detect_clog_only_when_sensor_enabled}, SENSOR_ENABLED: {sensor_enabled}"
	
	{% if enable_clog_detection and (sensor_enabled or not toolhead_detect_clog_only_when_sensor_enabled) %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_clog_detection %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_FILAMENT_END]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set clogged = true if params.CLOGGED|default(false)|lower == 'true' else false %}
	
	
	{% set unload_after_runout = printer["gcode_macro T%s" % toolhead].unload_after_runout|float %}
	
	
	{% if clogged %}
	_LED_FILAMENT_CLOG TOOLHEAD={toolhead}
	{% else %}
	_LED_FILAMENT_RUNOUT TOOLHEAD={toolhead}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_END" MSG="TOOLHEAD: {toolhead}"
	
	{% if printer.virtual_sdcard.is_active %}
	{% if not printer.pause_resume.is_paused %}
	PAUSE RUNOUT=True
	{% endif %}
	{% if not clogged and unload_after_runout %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	{% if not clogged and printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true'%}
	_JOIN_SPOOL TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M600]
description = Executes a color change by pausing the printer an unloading the filament.
gcode = 
	PAUSE
	UNLOAD_FILAMENT AUTOMATED=True
	RATOS_ECHO MSG="Please load new filament and resume"

[gcode_macro COLD_PULL]
description = Automated hotend cold pull.
gcode = 
	
	{% set extrusion_temp = params.EXTRUSION_TEMP|default(220)|int %}
	{% set cold_pull_temp = params.COLD_PULL_TEMP|default(80)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	
	{% if printer["dual_carriage"] is not defined %}
	{% set toolhead = 0 %}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead != 0 and toolhead != 1 %}
	{action_raise_error("Please select toolhead! 0 = left, 1 = right toolhead")}
	{% endif %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	RATOS_ECHO MSG="Starting cold pull on T{toolhead}..."
	{% else %}
	RATOS_ECHO MSG="Starting cold pull..."
	{% endif %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	SAVE_GCODE_STATE NAME=cold_pull_state
	
	
	{% if printer["dual_carriage"] is defined and "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	RATOS_ECHO MSG="Heating T{toolhead} to {extrusion_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={extrusion_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={extrusion_temp} MAXIMUM={extrusion_temp + 2}
	
	
	G4 P3000
	
	
	RATOS_ECHO MSG="extruding..."
	G92 E0
	G1 E30 F300
	G92 E0
	
	
	RATOS_ECHO MSG="Cooling T{toolhead} to {cold_pull_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={cold_pull_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={cold_pull_temp} MAXIMUM={cold_pull_temp + 2}
	
	
	G4 P10000
	
	
	RATOS_ECHO MSG="cold pull..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-40 VELOCITY=5 ACCEL=100
	
	
	RATOS_ECHO MSG="eject filament..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-200 VELOCITY=20 ACCEL=500
	
	
	RATOS_ECHO MSG="cooling down extruder..."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	RESTORE_GCODE_STATE NAME=cold_pull_state
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	
	CONSOLE_ECHO TITLE="Cold pull complete" MSG="Please remove the filament from the PTFE tube and cut the end off. Do NOT try to load it again." TYPE="warning"

[gcode_macro _USER_START_PRINT_BEFORE_HOMING]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_BED]
gcode = 

[gcode_macro _USER_START_PRINT_BED_MESH]
gcode = 

[gcode_macro _USER_START_PRINT_PARK]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 

[gcode_macro _USER_START_PRINT_HEAT_CHAMBER]
description = Uses the extruder sensor to wait for chamber temp. Override the _START_PRINT_HEAT_CHAMBER macro to implement heated chamber handling.
gcode = 
	
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}

[gcode_macro _USER_END_PRINT_BEFORE_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_AFTER_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_PARK]
gcode = 

[gcode_macro _USER_END_PRINT_FINISHED]
description = User hook for when the print is finished after gcode state has been restored.
gcode = 

[gcode_macro _USER_START_PRINT]
gcode = 

[gcode_macro _USER_END_START_PRINT]
gcode = 

[gcode_macro _USER_START_FEATURE]
gcode = 

[gcode_macro _USER_END_FEATURE]
gcode = 

[gcode_macro _USER_BEFORE_IDLE_TIMEOUT]
gcode = 

[gcode_macro _USER_AFTER_IDLE_TIMEOUT]
gcode = 

[gcode_macro ECHO_T_VARS]
description = Echo Toolhead variables to the console.
gcode = 
	{% set t = params.T|default(0) %}
	RATOS_ECHO MSG="T{t} Variables"
	{% for var, value in printer["gcode_macro T%s" % t].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ECHO_RATOS_VARS]
description = Echo RatOS variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro RatOS"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ENSURE_CRITICAL_RATOS_INIT]
variable_completed = False
gcode = 
	{% if not completed %}
	CALCULATE_PRINTABLE_AREA
	SET_GCODE_VARIABLE MACRO=ENSURE_CRITICAL_RATOS_INIT VARIABLE=completed VALUE=True
	{% endif %}

[delayed_gcode RATOS_INIT]
initial_duration = 0.1
gcode = 
	{action_respond_info("Initializing RatOS...")}
	ENSURE_CRITICAL_RATOS_INIT
	_LED_STANDBY
	INITIAL_FRONTEND_UPDATE
	_CHAMBER_FILTER_SANITY_CHECK
	{% if printer.fastconfig.settings.beacon is defined %}
	
	_BED_MESH_SANITY_CHECK
	{% endif %}
	{% set svv = printer.save_variables.variables %}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=0 C={svv.nozzle_expansion_coefficient_t0|default(0.06)|float}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=1 C={svv.nozzle_expansion_coefficient_t1|default(0.06)|float}
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=idex_applied_offset

[delayed_gcode RATOS_LOGO]
initial_duration = 2
gcode = 
	
	
	
	
	
	ENSURE_CRITICAL_RATOS_INIT
	HELLO_RATOS
	_ALERT_NON_ZERO_Z_OFFSET

[gcode_macro _ALERT_NON_ZERO_Z_OFFSET]
gcode = 
	{% set force = params.FORCE|default(0)|int == 1 %}
	{% set user_offset = printer.named_offsets.user_probe_z_offset.z|float %}
	{% set gcode_offset = printer.gcode_move.homing_origin.z|float %}
	{% set combined_offset = user_offset + gcode_offset %}
	
	{% if force or user_offset != 0 or gcode_offset != 0 %}
	{% set title = "User-adjusted Z-offset of %.3f mm is active" % combined_offset %}
	{% set msg = "" %}
	{% set nl = "" %}
	{% if user_offset != 0 %}
	{% set msg = msg + "beacon true zero user Z-offset: %.3f mm (to clear, use Z_OFFSET_APPLY_PROBE CLEAR=1)" % user_offset %}
	{% set nl = "_N_" %}
	{% endif %}
	{% if gcode_offset != 0 %}
	{% set msg = msg + nl + "G-code Z-offset: %.3f mm" % gcode_offset %}
	{% endif %}
	CONSOLE_ECHO TITLE="{title}" TYPE="info" MSG="{msg}"
	{% endif %}

[gcode_macro _INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE]
gcode = 
	{% set variable = params.VARIABLE|string %}
	{% set svv = printer.save_variables.variables %}
	{% set nlu_msg = "no longer used, please remove" %}
	{% if svv[variable] is defined %}
	{% set v = svv[variable]|string|replace('"', '')|replace("'", "") %}
	{% if not nlu_msg in v %}
	SAVE_VARIABLE VARIABLE={variable} VALUE='"{nlu_msg} (was {v})"'
	{% endif %}
	CONSOLE_ECHO TITLE="Deprecated ratos-variables.cfg variable" TYPE="warning" MSG="The variable {variable} is no longer used, please remove it from your ratos-variables.cfg file."
	{% endif %}

[gcode_macro _NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK]
gcode = 
	
	
	
	
	
	
	
	{% set t = params.T|int %}
	{% set c = params.C|float %}
	{% set normal_low = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_low|default(0.05)|float %}
	{% set normal_high = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_high|default(0.10)|float %}
	
	{% if c < 0 %}
	
	{action_emergency_stop("Invalid nozzle_expansion_coefficient_t%s value in ratos-variables.cfg: %.3f. It must be non-negative." % (t, c))}
	{% endif %}
	{% if c >= normal_high %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite high. Please verify that this is correct."
	{% endif %}
	{% if c <= normal_low %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite low. Please verify that this is correct."
	{% endif %}

[gcode_macro INITIAL_FRONTEND_UPDATE]
gcode = 
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_error = printer["gcode_macro RatOS"].status_color_error|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_unknown}"'
	{% endif %}
	
	
	{% set t0_sensor = "undefined" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	{% set t0_sensor = "detected" %}
	{% else %}
	{% set t0_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t0_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	{% set t1_sensor = "undefined" %}
	{% if printer["dual_carriage"] is defined and printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	{% set t1_sensor = "detected" %}
	{% else %}
	{% set t1_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t1_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	{% if svv.t0_filament is defined and printer["gcode_macro T0"] is defined %}
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	{% if t0_sensor != "empty" %}
	{% set t0_filament_type = svv.t0_filament[0]|default('')|string %}
	{% set t0_filament_name = svv.t0_filament[1]|default('')|string %}
	{% set t0_filament_temp = svv.t0_filament[2]|default(0)|float %}
	{% if t0_filament_name != '' and t0_filament_type != '' and t0_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{t0_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{t0_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={t0_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}
	{% if svv.t1_filament is defined and printer["gcode_macro T1"] is defined %}
	{% if printer["gcode_macro T1"].filament_name is defined and printer["gcode_macro T1"].filament_type is defined and printer["gcode_macro T1"].filament_temp is defined %}
	{% if t1_sensor != "empty" %}
	{% set t1_filament_type = svv.t1_filament[0]|default('')|string %}
	{% set t1_filament_name = svv.t1_filament[1]|default('')|string %}
	{% set t1_filament_temp = svv.t1_filament[2]|default(0)|float %}
	{% if t1_filament_name != '' and t1_filament_type != '' and t1_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='"{t1_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='"{t1_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE={t1_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t1_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro CALCULATE_PRINTABLE_AREA]
variable_calculated = False
gcode = 
	{% if not calculated %}
	{% set bed_margin_x = printer["gcode_macro RatOS"].bed_margin_x %}
	{% set bed_margin_y = printer["gcode_macro RatOS"].bed_margin_y %}
	
	
	
	{% set tool = 0 if printer["gcode_macro T0"] is not defined or printer["gcode_macro T0"].active else 1 %}
	{% set max_x = printer.toolhead.axis_maximum.x if printer["dual_carriage"] is defined and tool == 0 else printer.toolhead.axis_maximum.x - bed_margin_x[1] %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	
	
	{% set max_x = printer.toolhead.axis_maximum.x %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="printer.toolhead.axis_maximum.x {printer.toolhead.axis_maximum.x}"
	
	{% set max_y = printer.toolhead.axis_maximum.y - bed_margin_y[1]%}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_x_max VALUE={max_x}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_y_max VALUE={max_y}
	SET_GCODE_VARIABLE MACRO=CALCULATE_PRINTABLE_AREA VARIABLE=calculated VALUE=True
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	RATOS_LOG PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	{% endif %}

[gcode_macro CACHE_TOOLHEAD_SETTINGS]
variable_cache = {"global": {"accel": 1000, "ratio": 0.5, "speed": 50, "scv": 5}}
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set dummy = cache.__setitem__(key, {"accel": printer.toolhead.max_accel, "ratio": printer.toolhead.minimum_cruise_ratio, "speed": printer.toolhead.max_velocity, "scv": printer.toolhead.square_corner_velocity}) %}
	SET_GCODE_VARIABLE MACRO=CACHE_TOOLHEAD_SETTINGS VARIABLE=cache VALUE="{cache | pprint | replace("\n", "") | replace("\"", "\\\"")}"
	DEBUG_ECHO PREFIX="CACHE_TOOLHEAD_SETTINGS" MSG="Toolhead settings cached for {key}. {printer.toolhead.max_accel} accel, {printer.toolhead.minimum_cruise_ratio} ratio, {printer.toolhead.max_velocity} velocity, {printer.toolhead.square_corner_velocity} scv."

[gcode_macro RESTORE_TOOLHEAD_SETTINGS]
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set values = printer["gcode_macro CACHE_TOOLHEAD_SETTINGS"].cache.__getitem__(key) %}
	{% if values is not defined or values == 'None' %}
	{ action_raise_error("RESTORE_TOOLHEAD_SETTINGS: Toolhead settings not cached for key '" ~ key ~ "'.") }
	{% endif %}
	SET_VELOCITY_LIMIT ACCEL={values.accel} MINIMUM_CRUISE_RATIO={values.ratio} VELOCITY={values.speed} SQUARE_CORNER_VELOCITY={values.scv}
	DEBUG_ECHO PREFIX="RESTORE_TOOLHEAD_SETTINGS" MSG="Toolhead settings restored. {values.accel} accel, {values.ratio} ratio, {values.speed} velocity, {values.scv} scv."

[gcode_macro SET_MACRO_TRAVEL_SETTINGS]
gcode = 
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float %}
	{% set accel = printer["gcode_macro RatOS"].macro_travel_accel %}
	SET_VELOCITY_LIMIT ACCEL={accel} MINIMUM_CRUISE_RATIO=0.5 VELOCITY={speed} SQUARE_CORNER_VELOCITY={5}
	DEBUG_ECHO PREFIX="SET_MACRO_TRAVEL_SETTINGS" MSG="Macro travel settings set. {accel} accel, {speed} velocity"

[gcode_macro SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% if printer["dual_carriage"] is not defined %}
	
	SET_KINEMATIC_POSITION X={printable_x_max / 2} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	{% else %}
	
	IDEX_SET_CENTER_KINEMATIC_POSITION
	{% endif %}

[gcode_macro IDEX_SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x - (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x + (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY

[gcode_macro VERIFY_HYBRID_INVERTED]
gcode = 
	
	{% set inverted = False %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy is defined and printer.fastconfig.settings.ratos_hybrid_corexy.inverted is defined %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy.inverted|lower == 'true' %}
	{% set inverted = True %}
	{% endif %}
	{% endif %}
	{% if inverted == False %}
	{ action_emergency_stop("ratos_hybrid_corexy NOT INVERTED! Inverted hybrid core-xy bugfix not detected.") }
	{% endif %}

[gcode_macro RATOS_ECHO]
gcode = 
	{% set prefix = "RatOS" %}
	{% set debug = params.DEBUG|default(0)|int %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " | " ~ params.PREFIX %}
	{% endif %}
	{% set prefix = prefix ~ ":" %}
	{% set msg = "" %}
	{% if params.MSG is defined %}
	{% set msg = params.MSG %}
	{% else %}
	{% set msg = "No msg parameter provided (this is a bug or unintended use)." %}
	{% endif %}
	{% if not debug %}
	
	M117 {prefix} {msg}
	{% endif %}
	RATOS_LOG PREFIX="{prefix}" MSG="{msg}"
	{% if not debug %}
	RESPOND PREFIX="{prefix}" MSG="{msg}"
	{% else %}
	CONSOLE_ECHO TITLE="{prefix}" TYPE="debug" MSG="{msg}"
	{% endif %}

[gcode_macro ENABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=True
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=prefix_filter VALUE="'{params.FILTER|default('')|lower}'"
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging enabled."

[gcode_macro DISABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=False
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging disabled."

[gcode_macro DEBUG_ECHO]
variable_enabled = False
variable_prefix_filter = ''
gcode = 
	{% set prefix = "DEBUG" %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " - " ~ params.PREFIX %}
	{% endif %}
	{% if enabled and (prefix_filter|lower == '' or prefix_filter|lower in params.PREFIX|lower) %}
	RATOS_ECHO PREFIX="{prefix}" MSG="{params.MSG}" DEBUG=1
	{% endif %}

[gcode_macro START_FEATURE]
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="Start {params.FEATURE} feature gcode"
	{% set scv = printer.toolhead.square_corner_velocity|int|default(5) %}
	{% set accel = printer.toolhead.max_accel|int|default(10000) %}
	{% set ratio = printer.toolhead.minimum_cruise_ratio|float|default(0.5) %}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="scv" VALUE={scv}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="accel" VALUE={accel}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="ratio" VALUE={ratio}
	_USER_START_FEATURE FEATURE="{params.FEATURE}"

[gcode_macro END_FEATURE]
variable_scv = 5
variable_accel = 10000
variable_ratio = 0.5
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="End {params.FEATURE} feature gcode"
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={scv} ACCEL={accel} MINIMUM_CRUISE_RATIO={ratio}
	_USER_END_FEATURE FEATURE="{params.FEATURE}" SCV={scv} ACCEL={accel} RATIO={ratio}

[gcode_macro _ON_LAYER_CHANGE]
variable_layer_number = 0
description = INTERNAL USE ONLY. Call it from the slicers after layer change custom gcode
gcode = 
	
	{% set layer = params.LAYER|int %}
	
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE={layer}
	SET_PRINT_STATS_INFO CURRENT_LAYER={layer}

[gcode_macro _LEARN_MORE_CALIBRATION]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/calibration" %}
	{% set link_text = "RatOS Calibration Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_CHAMBER_FILTER]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter Control" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_FILAMENT]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/filaments" %}
	{% set link_text = "RatOS Filament Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _CONSOLE_SAVE_CONFIG]
gcode = 
	M118 Click <a class="command text--blue">SAVE_CONFIG</a> to save the settings to your printer.cfg.

[gcode_macro _LOAD_RATOS_SKEW_PROFILE]
gcode = 
	{% set ratos_skew_profile = printer["gcode_macro RatOS"].skew_profile|default("") %}
	{% if ratos_skew_profile != "" %}
	{% if printer.fastconfig.config["skew_correction %s" % ratos_skew_profile] is defined %}
	SKEW_PROFILE LOAD={ratos_skew_profile}
	GET_CURRENT_SKEW
	{% else %}
	{% set line_1 = '"Could not find skew profile %s!_N_Clearing skew correction."' % ratos_skew_profile %}
	CONSOLE_ECHO TITLE="Missing skew profile!" TYPE="warning" MSG={line_1}
	SET_SKEW CLEAR=1
	{% endif %}
	{% endif %}

[gcode_macro M601]
gcode = 
	PAUSE

[gcode_macro _STOP_AND_RAISE_ERROR]
gcode = 
	M84
	_RAISE_ERROR MSG="{params.MSG}"

[gcode_macro _RESET_GCODE_VARIABLES]
description = Reset specified [gcode_macro ...] variables to their original values from configuration when Klipper started.
	- MACRO: Name of the GCODE macro containing the variables to reset.
	- VARIABLES: Comma-separated list of variable names to reset (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- QUIET: (optional) If true, suppresses console echo messages for each reset variable. Default is false.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set quiet = params.QUIET|default("false")|lower in ("true", "1", "yes") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	{% set settings = printer.fastconfig.settings[obj_name|lower] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro %s]" % macro) }
	{% endif %}
	
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if settings["variable_%s" % var] is not defined %}
	{ action_raise_error("Variable '%s' is not defined in settings for [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	
	{% for var in vars %}
	{% set var_value = obj[var] %}
	{% if var_value is defined %}
	{% set v = settings["variable_%s" % var] %}
	{% if v != var_value|string %}
	{% if var_value is string %}
	{% set v = '"\'' ~ v|replace('"', '\\"')|replace("'", "\\'") ~ '\'"' %}
	{% endif %}
	SET_GCODE_VARIABLE MACRO={macro} VARIABLE={var} VALUE={v}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Reset {macro} variable {var} to original value: {v} (was {obj[var]})"
	{% endif %}
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro _SHOW_GCODE_VARIABLES]
description = Show current values of specified [gcode_macro ...] variables.
	- MACRO: Name of the GCODE macro containing the variables to show.
	- VARIABLES: Comma-separated list of variable names to show (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- PAD: (optional) If defined, provide a single character to use for padding variable names to align values in a tabular format in the console output. Default is no padding.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set pad = params.PAD|default("") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	
	{% set ns = namespace() %}
	{% set ns.max_len = 0 %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% set ns.max_len = (ns.max_len, var|length)|max %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if pad %}
	{% set padding = pad * (ns.max_len - var|length) %}
	CONSOLE_ECHO MSG="{var}{padding} {obj[var]}"
	{% else %}
	CONSOLE_ECHO MSG="{var}: {obj[var]}"
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro PAUSE]
description = Pauses the print
rename_existing = PAUSE_BASE
variable_extrude = 1.5
variable_retract = 1.5
variable_fan_speed = 0
variable_idex_mode = ""
variable_idex_toolhead = 0
variable_idex_toolhead_x = 0.0
variable_idex_toolhead_y = 0.0
variable_idex_toolhead_z = 0.0
gcode = 
	RATOS_ECHO MSG="Pausing print..."
	
	
	{% set runout_detected = true if params.RUNOUT|default(false)|lower == 'true' else false %}
	
	
	_LED_PAUSE
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	SAVE_GCODE_STATE NAME=PAUSE_state
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_mode VALUE='"{idex_mode}"'
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={idex_toolhead}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_x VALUE={printer.gcode_move.gcode_position.x|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_y VALUE={printer.gcode_move.gcode_position.y|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_z VALUE={printer.gcode_move.gcode_position.z|float}
	DEBUG_ECHO PREFIX="PAUSE" MSG="idex_mode: {idex_mode}, idex_toolhead: {idex_toolhead}, idex_toolhead_x: {idex_toolhead_x}, idex_toolhead_y: {idex_toolhead_y}, idex_toolhead_z: {idex_toolhead_z}"
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="pause"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if current_z < (max_z - 20.0) %}
	{% set z_safe = 20.0 %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	PAUSE_BASE
	
	
	{% if printer["dual_carriage"] is not defined %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan"].speed|float}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	{% if idex_toolhead == 0 %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t1"].speed|float}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106 S0
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set R = printer["gcode_macro PAUSE"].retract|float %}
	{% if can_extrude %}
	G91
	G1 E-{R} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	{% set pause_print_park_x = printer["gcode_macro RatOS"].pause_print_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].pause_print_park_in %}
	{% if runout_detected %}
	{% set pause_print_park_x = printer["gcode_macro RatOS"].runout_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].runout_park_in %}
	{% endif %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	DEBUG_ECHO PREFIX="PAUSE" MSG="z_speed: {z_speed}, pause_print_park_x: {pause_print_park_x}, pause_print_park_in: {pause_print_park_in}, default_toolhead: {default_toolhead}"
	{% if "xyz" in printer.toolhead.homed_axes %}
	G91
	G1 Z{z_safe} F{z_speed}
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% else %}
	
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	_IDEX_SINGLE X={parking_position}
	{% else %}
	PARK_TOOLHEAD
	{% endif %}
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="pause"
	
	RATOS_ECHO MSG="Print paused"

[gcode_macro RESUME]
description = Resumes the print if the printer is paused.
rename_existing = RESUME_BASE
gcode = 
	
	
	RATOS_ECHO MSG="Resuming print..."
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	
	{% set target_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set target_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if target_idex_mode != '' %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set fan_speed = printer["gcode_macro PAUSE"].fan_speed|float %}
	{% if printer["dual_carriage"] is not defined %}
	M106 S{(fan_speed * 255)}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% else %}
	{% if params.TOOLHEAD is defined %}
	
	{% if params.TOOLHEAD == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% else %}
	{% if printer["gcode_macro PAUSE"].idex_toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	{% if params.TOOLHEAD is defined %}
	_SELECT_TOOL T={params.TOOLHEAD} X=-1 Y=-1 TOOLSHIFT=false
	{% else %}
	_SELECT_TOOL T={printer["gcode_macro PAUSE"].idex_toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	{% endif %}
	
	{% set x = printer["gcode_macro PAUSE"].idex_toolhead_x|float %}
	{% set y = printer["gcode_macro PAUSE"].idex_toolhead_y|float %}
	{% set z = printer["gcode_macro PAUSE"].idex_toolhead_z|float %}
	G1 X{x} Y{y} Z{z} F{speed}
	{% if params.TOOLHEAD is defined %}
	
	SAVE_GCODE_STATE NAME=PAUSE_STATE
	{% endif %}
	{% endif %}
	
	
	{% if params.TOOLHEAD is not defined %}
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% if can_extrude %}
	G91
	G1 E{E} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1 MOVE_SPEED={speed}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	RESUME_BASE
	
	
	_LED_PRINTING
	
	RATOS_ECHO MSG="Print resumed"

[gcode_macro CANCEL_PRINT]
description = Cancels the print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	RATOS_ECHO MSG="Cancelling print..."
	END_PRINT
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	
	CANCEL_PRINT_BASE
	RATOS_ECHO MSG="Print cancelled"

[gcode_macro START_PRINT]
description = Start print procedure, use this in your Slicer.
variable_post_processor_version = 2
variable_is_printing_gcode = False
variable_both_toolheads = True
variable_object_xoffset = 0
variable_first_x = -1
variable_first_y = -1
variable_total_toolshifts = 0
variable_initial_tool = 0
variable_extruder_first_layer_temp = ""
variable_extruder_other_layer_temp = ""
gcode = 
	
	{% if params.EXTRUDER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_TEMP parameter not found.")}
	{% endif %}
	{% if params.EXTRUDER_OTHER_LAYER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_OTHER_LAYER_TEMP parameter not found.")}
	{% endif %}
	{% if params.BED_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. BED_TEMP parameter not found.")}
	{% endif %}
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' and printer["gcode_macro RatOS"].danger_force_allow_auto_center_subject|default(false)|lower != 'true'%}
	
	
	
	
	
	{ action_raise_error("The experimental auto_center_subject feature is not supported in this version of RatOS. Please disable it in the RatOS macro settings.") }
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes and printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% if printer["gcode_macro _VAOC"].is_started|default(true)|lower == 'true' %}
	_VAOC_END
	{% endif %}
	{% endif %}
	
	
	_LED_START_PRINTING
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_USER_START_PRINT { rawparams }
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_probe_stowable = printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% endif %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	{% set X0 = params.X0|default(-1)|float %}
	{% set X1 = params.X1|default(-1)|float %}
	{% set Y0 = params.Y0|default(-1)|float %}
	{% set Y1 = params.Y1|default(-1)|float %}
	{% if first_x == -1 or first_y == -1 %}
	{% set first_x = params.FIRST_X|default(-1)|float %}
	{% set first_y = params.FIRST_Y|default(-1)|float %}
	{% endif %}
	{% set total_toolshifts = params.TOTAL_TOOLSHIFTS|default(0)|int %}
	{% set initial_tool = params.INITIAL_TOOL|default(default_toolhead)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	
	
	
	
	
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(printer.heater_bed.target, true)|float %}
	
	
	{% set total_layer_count = params.TOTAL_LAYER_COUNT|default(0)|int %}
	{% set extruder_first_layer_temp = (params.EXTRUDER_TEMP|default("")).split(",") %}
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL BEACON_CONTACT_START_PRINT_TRUE_ZERO={beacon_contact_start_print_true_zero} BEACON_CONTACT_CALIBRATE_MODEL_ON_TRUE_ZERO={beacon_contact_calibrate_model_on_true_zero}
	{% endif %}
	
	_START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH BED_TEMP={bed_temp}
	
	
	RATOS_ECHO MSG="First print coordinates X:{first_x} Y:{first_y}"
	
	
	{% if params.TOTAL_LAYER_COUNT is not defined %}
	{% set link_url = "https://os.ratrig.com/docs/slicers" %}
	{% set link_text = "RatOS Slicer Configuration" %}
	{% set line_1 = '"Your slicer gcode settings are not up to date._N_Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="Incomplete Slicer Configuration detected" TYPE="warning" MSG={line_1}
	{% endif %}
	
	
	SET_PRINT_STATS_INFO CURRENT_LAYER=1
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE=1
	{% if total_layer_count > 0 %}
	SET_PRINT_STATS_INFO TOTAL_LAYER={total_layer_count}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads %}
	{% set initial_tool = 0 if initial_tool == 1 else 1 %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	{% endif %}
	
	
	{% set both_toolheads = true %}
	{% if total_toolshifts == 0 %}
	{% set both_toolheads = false %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	{% endif %}
	{% if both_toolheads and (idex_mode == "copy" or idex_mode == "mirror") %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Gcode tool changes found. Copy and mirror mode do not support toolchanges.")}
	{% endif %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set both_toolheads = true %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=initial_tool VALUE={initial_tool}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_x VALUE={first_x}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_y VALUE={first_y}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=total_toolshifts VALUE={total_toolshifts}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=both_toolheads VALUE={both_toolheads}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_first_layer_temp VALUE="'{params.EXTRUDER_TEMP}'"
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_other_layer_temp VALUE="'{params.EXTRUDER_OTHER_LAYER_TEMP}'"
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE=0
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set svv = printer.save_variables.variables %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set stepper_x_position_min = printer.fastconfig.settings.stepper_x.position_min|float %}
	{% set stepper_x_position_endstop = printer.fastconfig.settings.stepper_x.position_endstop|float %}
	{% set dual_carriage_position_max = printer.fastconfig.settings.dual_carriage.position_max|float %}
	{% set dual_carriage_position_endstop = printer.fastconfig.settings.dual_carriage.position_endstop|float %}
	{% set x_parking_space = parking_position_t0 - (stepper_x_position_endstop , stepper_x_position_min)|max %}
	{% set dc_parking_space = (dual_carriage_position_endstop , dual_carriage_position_max)|min - parking_position_t1 %}
	{% if svv.idex_xoffset|abs >= (x_parking_space - 0.5) or svv.idex_xoffset|abs >= (dc_parking_space - 0.5) %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Toolhead x-offset is too high for the available parking space. Calibrate your X and DC endstop positions and make sure you stay below 1mm." % (copy_mode_max_width)) }
	{% endif %}
	{% endif %}
	
	
	{% if (idex_mode == "copy" or idex_mode == "mirror") and printer.fastconfig.settings.ratos.enable_gcode_transform %}
	
	{% if params.MIN_X is not defined or params.MAX_X is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Something went wrong! Missing important post processor start print parameter!") }
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE=0
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	
	{% set boundary_box_min_x = params.MIN_X|default(0)|float %}
	{% set boundary_box_max_x = params.MAX_X|default(printable_x_max)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if default_toolhead == 0 %}
	
	{% set boundary_box_max_x = boundary_box_max_x + svv.idex_xoffset %}
	{% else %}
	
	{% set boundary_box_min_x = boundary_box_min_x - svv.idex_xoffset %}
	{% endif %}
	
	{% set center_x = printable_x_max / 2.0 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set object_width = boundary_box_max_x - boundary_box_min_x %}
	{% set copy_mode_max_width = center_x %}
	{% set mirror_mode_max_width = center_x - safe_distance / 2.0 %}
	
	DEBUG_ECHO PREFIX="START_PRINT" MSG="OBJECT_WIDTH: {object_width} BOUNDARY_BOX_MIN_X: {boundary_box_min_x} BOUNDARY_BOX_MAX_X: {boundary_box_max_x} CENTER_X: {center_x} SAFE_DISTANCE: {safe_distance}"
	
	
	{% if idex_mode == "copy" and object_width > copy_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for copy mode! Max supported width is %s mm" % (copy_mode_max_width)) }
	{% endif %}
	{% if idex_mode == "mirror" and object_width > mirror_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for mirror mode! Max supported width is %s mm" % (mirror_mode_max_width)) }
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = (printable_x_max - boundary_box_max_x - boundary_box_min_x) / 2 %}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE={object_xoffset}
	{% endif %}
	
	{% endif %}
	
	
	{% set has_initial_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_toolhead_filament_sensor %}
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% set has_initial_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_bowden_filament_sensor %}
	
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% if printer["dual_carriage"] is defined and both_toolheads %}
	
	{% set has_secondary_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set has_secondary_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_CHAMBER_FILTER_ON AT="before_print_start"
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true' %}
	{% if both_toolheads %}
	RATOS_ECHO MSG="Spool join is not possible if both toolheads are in use!"
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	{% endif %}
	
	
	CLEAR_PAUSE
	{% if printer["gcode_macro RatOS"].force_absolute_position|lower == 'true' %}
	G90
	{% endif %}
	SAVE_GCODE_STATE NAME=start_print_state
	
	
	G21
	
	G90
	
	M82
	_USER_START_PRINT_BEFORE_HOMING { rawparams }
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_BEGIN_BATCH
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_Z_HOP
	
	
	{% if idex_mode != '' and not (printer.fastconfig.settings.beacon is defined and (beacon_contact_start_print_true_zero or beacon_adaptive_heat_soak)) %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	{% if chamber_temp > 0 %}
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED={printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float}
	{% endif %}
	{% endif %}
	_CHAMBER_HEATER_ON START_CHAMBER_TEMP={start_chamber_temp} CHAMBER_TEMP={chamber_temp}
	_USER_START_PRINT_HEAT_CHAMBER { rawparams } CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_START_PRINT_BEFORE_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	RATOS_ECHO MSG="Heating bed..."
	
	M190 S{bed_temp}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_adaptive_heat_soak %}
	_MOVE_TO_SAFE_Z_HOME
	
	G1 Z2.5 F{z_speed}
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK LAYER_QUALITY={beacon_adaptive_heat_soak_layer_quality} MAXIMUM_FIRST_LAYER_DURATION={beacon_adaptive_heat_soak_maximum_first_layer_duration} MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={beacon_adaptive_heat_soak_max_wait}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_BED { rawparams }
	
	
	_START_PRINT_AFTER_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	_USER_START_PRINT_BED_MESH { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_BED_MESH X0={X0} X1={X1} Y0={Y0} Y1={Y1} T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_END_BATCH
	{% endif %}
	
	
	{% if idex_mode == '' %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[initial_tool]|float}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[0]|float}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={extruder_first_layer_temp[1]|float}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_PARK { rawparams }
	
	
	_START_PRINT_PARK
	
	
	RATOS_ECHO MSG="Heating Extruder..."
	{% if idex_mode == '' %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[initial_tool]|float}  MAXIMUM={extruder_first_layer_temp[initial_tool]|float + 5}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[0]|float}  MAXIMUM={extruder_first_layer_temp[0]|float + 5}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder1" MINIMUM={extruder_first_layer_temp[1]|float}  MAXIMUM={extruder_first_layer_temp[1]|float + 5}
	{% endif %}
	{% endif %}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	{% if idex_mode == '' %}
	_LED_PRINTING
	{% else %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	_LED_PRINTING
	{% else %}
	{% if both_toolheads %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	{% if toolchange_standby_temp > -1 %}
	_LED_TOOLHEAD_STANDBY TOOLHEAD={0 if initial_tool == 1 else 1}
	{% else %}
	_LED_PRINTING TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% else %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_EXTRUDER { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_AFTER_HEATING_EXTRUDER X0={X0} X1={X1} Y0={Y0} Y1={Y1} INITIAL_TOOLHEAD={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if idex_mode != '' %}
	{% if not both_toolheads %}
	{% if initial_tool != default_toolhead %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if idex_mode != '' %}
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=standby VALUE=False
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=standby VALUE=False
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if initial_tool == 1 else 'extruder1'} TARGET={toolchange_standby_temp}
	SET_GCODE_VARIABLE MACRO=T{0 if initial_tool == 1 else 1} VARIABLE=standby VALUE=True
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=start_print_state
	
	{% if printer["dual_carriage"] is defined %}
	_SET_IDEX_MODE_OFFSET
	{% endif %}
	
	
	{% if idex_mode != '' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% if idex_mode == "copy" and idex_mode != act_idex_mode %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == "mirror" and idex_mode != act_idex_mode %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={object_xoffset} MOVE=0
	{% endif %}
	{% else %}
	_SELECT_TOOL T={initial_tool} TOOLSHIFT=false
	_SET_TOOLHEAD_OFFSET
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	_SET_EXTRUSION_MODE
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={printer["print_stats"].print_duration}
	{% endif %}
	
	
	_USER_END_START_PRINT { rawparams }
	
	G92 E0
	
	
	_CHAMBER_FILTER_ON AT="after_print_start"
	
	_ALERT_NON_ZERO_Z_OFFSET
	
	RATOS_ECHO MSG="Printing..."

[gcode_macro _START_PRINT_BEFORE_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set is_stowable_probe = true if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' else false %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Pre-heating extruder..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={min_temp}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET={min_temp}
	{% endif %}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	{% endif %}
	{% endif %}
	
	
	{% if not is_stowable_probe %}
	{% if printer["dual_carriage"] is defined and act_t != default_toolhead %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	{% endif %}
	RATOS_ECHO MSG="Heat soaking z probe..."
	_MOVE_TO_SAFE_Z_HOME
	
	G0 Z2 F{z_speed}
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Waiting for extruder to be preheated..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	{% if default_toolhead == 0 %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_Z_HOP
	{% endif %}
	
	
	{% if auto_z_offset_calibration %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	PARK_TOOLHEAD
	_CLEANING_MOVE TOOLHEAD={default_toolhead} AUTOMATED=True
	_SELECT_TOOL T={0 if default_toolhead == 1 else 1} X={parking_position_t0 if default_toolhead == 1 else parking_position_t1} Y=0 TOOLSHIFT=false
	_CLEANING_MOVE TOOLHEAD={0 if default_toolhead == 1 else 1} AUTOMATED=True
	_VAOC_CALIBRATE_Z_OFFSET AUTO_Z_OFFSET=True
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=false
	{% endif %}
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	{% if needs_rehoming %}
	G28 Z
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	_START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE
	{% endif %}
	{% endif %}
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	PROBE PROBE_METHOD=contact SAMPLES=1

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	{% set fuzzy_radius = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_radius|default(0)|float if beacon_contact_start_print_true_zero_fuzzy_position else 0 %}
	
	{% set contact_true_zero_temp_has_been_set = False %}
	
	
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	
	
	
	{% if printer.beacon.last_probe_result|lower == "ok" %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	RATOS_ECHO MSG="Auto calibration nozzle wipe with probe result {last_z_offset}..."
	G0 Z{(0.2 + last_z_offset)} F{z_speed}
	G0 X70 F300
	{% else %}
	RATOS_ECHO MSG="Skipping auto calibration nozzle wipe because probing failed!"
	{% endif %}
	{% elif beacon_contact_wipe_before_true_zero_method == "probe_clean" %}
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	
	{% set contact_true_zero_temp_has_been_set = True %}
	
	
	
	
	
	
	
	
	BEACON_PROBE_CLEAN X=50 Y=10
	{% else %}
	CONSOLE_ECHO TYPE="error" TITLE="Unknown wipe method" MSG="Unknown wipe method '{beacon_contact_wipe_before_true_zero_method}' configured, skipping wipe before beacon true zero."
	{% endif %}
	{% endif %}
	
	
	G0 Z5 F{z_speed}
	_MOVE_TO_SAFE_Z_HOME FUZZY_RADIUS={fuzzy_radius}
	
	
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION
	
	{% if not contact_true_zero_temp_has_been_set %}
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon contact auto calibration..."
	
	{% if beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	
	G0 Z5 F{z_speed}

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION]
gcode = 
	{% set pos = printer.ratos.last_move_to_safe_z_home_position %}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE={pos[0]}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE={pos[1]}

[gcode_macro _START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set first_x = printer["gcode_macro START_PRINT"].first_x|default(-1)|float %}
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2.0 %}
	{% set center_y = printable_y_max / 2.0 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% if printer["dual_carriage"] is defined %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% endif %}
	
	
	{% set X0 = params.X0|default(-1)|int %}
	{% set X1 = params.X1|default(-1)|int %}
	{% set Y0 = params.Y0|default(-1)|int %}
	{% set Y1 = params.Y1|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	
	{% if idex_mode == '' %}
	
	_PRIME
	{% else %}
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	RATOS_ECHO PREFIX="IDEX" MSG="using combined prime offset for IDEX {idex_mode} mode"
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	{% if both_toolheads %}
	{% if initial_toolhead == 0 %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T{initial_toolhead}"
	_SELECT_TOOL T={initial_toolhead} TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	SET_MACRO_TRAVEL_SETTINGS
	
	{% if (X0 > -1 and Y1 > -1) or (first_x > 0 and first_y > 0) %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	{% endif %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	{% set first_z = 1 %}
	{% else %}
	{% set first_z = 3 %}
	{% endif %}
	
	
	{% if idex_mode == "mirror" %}
	{% if first_y >= 0 %}
	G0 Y{first_y} F{speed}
	{% else %}
	G0 Y{Y1} F{speed}
	{% endif %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={initial_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={initial_toolhead} E={printer["gcode_macro RatOS"].toolchange_first_purge|default(50)|float}
	_CLEANING_MOVE TOOLHEAD={initial_toolhead} AUTOMATED=True
	{% endif %}
	{% if first_x >= 0 and first_y >= 0 %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% else %}
	{% set first_x = X0 %}
	{% set first_y = Y0 %}
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'min' %}
	{% set first_x = X0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'max' %}
	{% set first_x = X1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|float <= center_x %}
	{% set first_x = X0 %}
	{% else %}
	{% set first_x = X1 %}
	{% endif %}
	{% endif %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'min' %}
	{% set first_y = Y0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'max' %}
	{% set first_y = Y1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|float <= center_y %}
	{% set first_y = Y0 %}
	{% else %}
	{% set first_y = Y1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	
	
	_LOAD_RATOS_SKEW_PROFILE

[gcode_macro _PRIME]
gcode = 
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	PRIME_BLOB INITIAL_TOOLHEAD={params.INITIAL_TOOLHEAD} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={params.IDEX_MODE} Y1={params.Y1}
	{% else %}
	
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif params.IDEX_MODE == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro END_PRINT]
description = End print procedure, use this in your Slicer.
gcode = 
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SAVE_GCODE_STATE NAME=end_print_state
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = printer["gcode_macro START_PRINT"].object_xoffset|default(0)|float %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(0-object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={(0-object_xoffset)}
	{% endif %}
	{% endif %}
	
	
	_USER_END_PRINT_BEFORE_HEATERS_OFF { rawparams }
	_END_PRINT_BEFORE_HEATERS_OFF
	TURN_OFF_HEATERS
	_USER_END_PRINT_AFTER_HEATERS_OFF { rawparams }
	_END_PRINT_AFTER_HEATERS_OFF
	_USER_END_PRINT_PARK { rawparams }
	_END_PRINT_PARK
	
	
	{% if printer["gcode_macro RatOS"].skew_profile is defined %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined and printer["gcode_macro RatOS"].end_print_motors_off|lower != 'false' %}
	
	M84
	{% endif %}
	
	
	M107
	
	
	BED_MESH_CLEAR
	RATOS_ECHO MSG="Done :)"
	
	
	RESTORE_GCODE_STATE NAME=end_print_state
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	M84
	{% endif %}
	
	
	RESET_NAMED_OFFSET EVENT="end_print"
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_CHAMBER_FILTER_ON AT="print_end"
	_CHAMBER_FILTER_OFF
	
	
	_CHAMBER_HEATER_OFF
	
	_USER_END_PRINT_FINISHED { rawparams }

[gcode_macro _END_PRINT_BEFORE_HEATERS_OFF]
gcode = 
	RATOS_ECHO MSG="Cleaning up..."

[gcode_macro _END_PRINT_AFTER_HEATERS_OFF]
gcode = 
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% set z_hop = printer["gcode_macro RatOS"].end_print_park_z_hop|float %}
	{% set r = printer["gcode_macro RatOS"].end_print_retract_filament|default(4)|float %}
	{% if current_z < (max_z - z_hop) %}
	{% set z_safe = z_hop %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G91
	
	{% if can_extrude %}
	G1 E-2 F3600
	{% endif %}
	
	G0 Z{z_safe} F3600
	
	{% if can_extrude %}
	G1 E-{(r-2)} F3600
	{% endif %}
	
	G90

[gcode_macro _SET_EXTRUSION_MODE]
gcode = 
	
	{% if printer["gcode_macro RatOS"].relative_extrusion|lower == 'true' %}
	M83
	{% else %}
	M82
	{% endif %}

[gcode_macro GENERATE_SHAPER_GRAPHS]
description = Genarates input shaper resonances graphs for analysis. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	{% set hz_per_sec = params.HZ_PER_SEC|default(1)|float %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set copy_mode_offset = printable_x_max / 4.0 %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	_IDEX_SINGLE
	{% endif %}
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	
	
	{% if idex_mode != 'copy' and idex_mode != 'mirror' %}
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	{% endif %}
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Shaper graph"

[gcode_shell_command generate_shaper_graph_x]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-x.sh
timeout = 60.
verbose = True

[gcode_shell_command generate_shaper_graph_y]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-y.sh
timeout = 60.
verbose = True

[gcode_macro MEASURE_COREXY_BELT_TENSION]
description = Generates resonance graph used to ensure belts are equally tensioned. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	_IDEX_SINGLE
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if measure_t1 == false or measure_t0 == false %}
	{action_raise_error("Axis specified. Not supported for belt tension on Y.")}
	{% else %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	G4 P5000
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	PARK_TOOLHEAD
	{% endif %}
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	G1 X{parking_position_t1} F{speed}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	
	
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Belt Tension Graph"

[gcode_shell_command generate_belt_tension_graph]
command = /home/pi/printer_data/config/RatOS/scripts/generate-belt-tension-graph.sh
timeout = 90.
verbose = True

[idle_timeout]
gcode = 
	{% if printer.webhooks.state|lower == 'ready' %}
	{% if printer.pause_resume.is_paused|lower == 'false' %}
	_USER_BEFORE_IDLE_TIMEOUT
	RATOS_ECHO PREFIX="IDLE" MSG="2 hours since last activity. Powering off heaters and motors.."
	TURN_OFF_HEATERS
	M84
	_USER_AFTER_IDLE_TIMEOUT
	{% endif %}
	{% endif %}
timeout = 7200

[temperature_sensor raspberry_pi]
sensor_type = temperature_host

[skew_correction]

[named_offsets]

[input_shaper]

[virtual_sdcard]
path = ~/printer_data/gcodes

[display_status]

[pause_resume]

[force_move]
enable_force_move = True

[respond]

[resonance_generator]

[ratos]
allow_unknown_gcode_generator = True
enable_gcode_transform = True

[exclude_object]

[bed_mesh]
split_delta_z = 0.001
horizontal_move_z = 2
mesh_min = 20,20
mesh_max = 480,480
probe_count = 40,40
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = .2
speed = 600
log_points = False

[fastconfig]

[heater_bed]
heater_pin = heater_bed_heating_pin
sensor_pin = heater_bed_sensor_pin
sensor_type = Generic 3950
min_temp = 0
max_temp = 140
pwm_cycle_time = 0.103
control = pid
pid_kp = 61.987
pid_ki = 1.781
pid_kd = 539.289

[printer]
kinematics = ratos_hybrid_corexy
max_velocity = 800
max_accel = 10000
minimum_cruise_ratio = 0.5
max_z_velocity = 50
max_z_accel = 600
square_corner_velocity = 5

[ratos_hybrid_corexy]
inverted = true

[dual_carriage]
axis = x
safe_distance = 55
position_max = 559.6
position_endstop = 559.6
position_min = 0
step_pin = PF9
dir_pin = dual_carriage_dir_pin
enable_pin = !PG2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t1:PA2

[gcode_macro _SET_IDEX_MODE_OFFSET]
description = "Internal use only. Sets the 'idex_mode' named offset that the active idex mode requires."
gcode = 
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_SET_IDEX_MODE_OFFSET" MSG="idex_mode: {idex_mode}, center_x: {center_x}"
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	SET_NAMED_OFFSET NAME=idex_mode X={(-center_x / 2)}
	{% else %}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% else %}
	{action_raise_error("_SET_IDEX_MODE_OFFSET: Printer not homed")}
	{% endif %}

[gcode_macro IDEX_SINGLE]
gcode = 
	_IDEX_REMAP_TOOLHEADS ENABLE=False
	_IDEX_SINGLE

[gcode_macro _IDEX_SINGLE]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_single"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set init = params.INIT|default(0)|int %}
	{% set new_x = params.X|default(-1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_default_t = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="init: {init}, new_x: {new_x}, idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, act_t: {act_t}"
	
	{% if idex_mode == "copy" or idex_mode == "mirror" or init == 1 %}
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="reset idex_mode offset"
	G1 X{center_x} F{(speed)}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="activate default carriage"
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolheads"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	G90
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position."
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1}
	G1 X{parking_position_default_t} F{speed}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move default toolhead to its new position."
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% if new_x == -1 %}
	{% set new_x = center_x %}
	{% endif %}
	G1 X{new_x} F{speed}
	
	M400
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="X Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set extruder motion queue."
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if default_toolhead==0 else default_toolhead}
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolhead offset."
	_SET_TOOLHEAD_OFFSET
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set input shaper."
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[default_toolhead]|float)} SHAPER_FREQ_Y={(shaper_y_freq[default_toolhead]|float)} SHAPER_TYPE_X={(shaper_x_type[default_toolhead]|lower)} SHAPER_TYPE_Y={(shaper_y_type[default_toolhead]|lower)}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="update Frontend."
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if default_toolhead==0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if default_toolhead==1 else False}
	{% else %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_single"

[gcode_macro IDEX_COPY]
gcode = 
	_IDEX_COPY

[gcode_macro _IDEX_COPY]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_copy"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set y = params.Y|default(-1)|int %}
	{% set dance = params.DANCE|default(1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_COPY" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}, y: {y}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "copy" %}
	{% if idex_mode == "mirror" %}
	{% if y>=0 %}
	G1 X{center_x} Y{y} F{(speed)}
	{% else %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	
	
	{% if idex_mode != "mirror" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance == 1 %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[2]|float)} SHAPER_FREQ_Y={(shaper_y_freq[2]|float)} SHAPER_TYPE_X={(shaper_x_type[2]|lower)} SHAPER_TYPE_Y={(shaper_y_type[2]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_copy"

[gcode_macro IDEX_MIRROR]
gcode = 
	_IDEX_MIRROR

[gcode_macro _IDEX_MIRROR]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_mirror"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set dance = params.DANCE|default(1)|int %}
	{% set priming = params.PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_MIRROR" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "mirror" %}
	
	{% if idex_mode == "copy" %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS MIRROR_PRIMING={params.PRIMING}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=MIRROR
	
	
	{% if idex_mode != "copy" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance and not priming %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[3]|float)} SHAPER_FREQ_Y={(shaper_y_freq[3]|float)} SHAPER_TYPE_X={(shaper_x_type[3]|lower)} SHAPER_TYPE_Y={(shaper_y_type[3]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_mirror"

[gcode_macro _IDEX_SET_TOOLHEADS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set mirror_priming = params.MIRROR_PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position_inactive_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_IDEX_SET_TOOLHEADS" MSG="idex_mode: {idex_mode}, act_t: {act_t}, center_x: {center_x}, mirror_priming: {mirror_priming}"
	
	
	{% if act_t != default_toolhead %}
	_SET_TOOLHEAD_OFFSET FORCE_TOOLHEAD={default_toolhead} MOVE=1
	{% endif %}
	
	{% if mirror_priming %}
	
	
	
	{% if parking_position_t0|abs < parking_position_t1 - printable_x_max %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{printable_x_max + parking_position_t0|abs} F{(speed)}
	{% else %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{0 - (parking_position_t1 - printable_x_max)} F{(speed)}
	{% endif %}
	
	{% else %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1} MODE=PRIMARY
	G1 X{parking_position_inactive_t} F{(speed)}
	
	
	{% if act_t==1 %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{center_x / 2} F{(speed)}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"

[gcode_macro IDEX_PARK]
gcode = 
	
	PARK_TOOLHEAD

[gcode_macro PARK_TOOLHEAD]
gcode = 
	
	{% set idex_mode = 'none' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="PARK_TOOLHEAD" MSG="Parking T{act_t}.."
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set parking_position_inact_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set printable_y_min = printer["gcode_macro RatOS"].printable_y_min|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" and 'xy' in printer.toolhead.homed_axes %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% elif printer.toolhead.position.y|float < printable_y_min %}
	G1 Y{printable_y_min} F{speed}
	{% endif %}
	
	SAVE_GCODE_STATE NAME=_PARK_TOOLHEAD
	G90
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0.5
	
	
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_inact_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	
	SET_VELOCITY_LIMIT ACCEL={printer.toolhead.max_accel} MINIMUM_CRUISE_RATIO=0.5
	M400
	RESTORE_GCODE_STATE NAME=_PARK_TOOLHEAD
	
	{% endif %}

[gcode_macro JOIN_SPOOLS]
gcode = 
	
	{% set spools = params.SPOOLS|default("") %}
	
	{% if spools == "" %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% else %}
	{% if spools != "0,1" and spools != "1,0" %}
	RATOS_ECHO MSG="Wrong spool configuration!"
	RATOS_ECHO MSG="Join Spools = JOIN_SPOOLS SPOOLS=0,1"
	RATOS_ECHO MSG="Deactivate = JOIN_SPOOLS SPOOLS="
	{% else %}
	{% if spools == "0,1" or spools == "1,0" %}
	_IDEX_JOIN_SPOOLS ENABLE=true
	{% else %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_JOIN_SPOOLS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if enable %}
	{% set has_t0_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t1_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t0_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined else false %}
	{% set has_t1_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined else false %}
	{% if (has_t0_toolhead_filament_sensor and has_t1_toolhead_filament_sensor) or (has_t0_bowden_filament_sensor and has_t1_bowden_filament_sensor) %}
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=True
	RATOS_ECHO MSG="Spool joining enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Can not enable spool joining! No filament sensors found."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining deactivated!"
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining is not possible in copy and mirror mode!"
	{% endif %}

[gcode_macro _JOIN_SPOOL]
gcode = 
	
	{% set old_toolhead = params.TOOLHEAD|int %}
	{% set new_toolhead = 0 if old_toolhead == 1 else 1 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set purge_after_load = printer["gcode_macro T%s" % new_toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_JOIN_SPOOL" MSG="toolhead: {new_toolhead}"
	
	{% set has_filament = true %}
	{% set has_new_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% set has_new_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% if has_new_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	{% if has_new_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	
	{% if has_filament %}
	RATOS_ECHO MSG="Joining spools! Please wait for extruder to heat up...."
	
	
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={new_toolhead}
	
	
	_DEACTIVATE_TOOLHEAD TOOLHEAD={old_toolhead}
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set extruder_temp = extruder_first_layer_temp[new_toolhead]|float %}
	{% else %}
	{% set extruder_temp = extruder_other_layer_temp[new_toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if new_toolhead == 0 else 'extruder1'} TARGET={extruder_temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if new_toolhead == 0 else 'extruder1'} MINIMUM={extruder_temp}  MAXIMUM={extruder_temp + 5}
	
	
	{% if purge_after_load > 0 %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_toolhead == 0 else new_toolhead}
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={new_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={new_toolhead} E={purge_after_load}
	_CLEANING_MOVE TOOLHEAD={new_toolhead} AUTOMATED=True
	
	
	SET_DUAL_CARRIAGE CARRIAGE={old_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if old_toolhead == 0 else old_toolhead}
	
	{% endif %}
	
	
	RESUME TOOLHEAD={new_toolhead}
	
	
	_IDEX_JOIN_SPOOLS ENABLE=false
	
	{% else %}
	{ action_raise_error("Spool join failed! No filament found or filament sensor is disabled.") }
	{% endif %}

[gcode_macro REMAP_TOOLHEADS]
gcode = 
	
	{% set toolheads = params.TOOLHEADS|default("") %}
	
	{% if toolheads == "" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% else %}
	{% if toolheads != "0,1" and toolheads != "1,0" %}
	RATOS_ECHO MSG="Wrong toolhead configuration!"
	RATOS_ECHO MSG="Remap = REMAP_TOOLHEADS TOOLHEADS=0,1"
	RATOS_ECHO MSG="Deactivate = REMAP_TOOLHEADS TOOLHEADS="
	{% else %}
	{% if toolheads == "0,1" or toolheads == "1,0" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=true
	_IDEX_SINGLE
	{% else %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_REMAP_TOOLHEADS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	{% if not enable or (idex_mode != "copy" and idex_mode != "mirror") %}
	{% if enable %}
	RATOS_ECHO MSG="Toolhead remapping enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping deactivated!"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE={enable}
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping not possible in copy and mirror mode!"
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	{% endif %}

[gcode_macro SHAPER_CALIBRATE]
rename_existing = SHAPER_CALIBRATE_ORG
gcode = 
	RATOS_ECHO PREFIX="IDEX" MSG="SHAPER_CALIBRATE is useless on IDEX machines. Please use the GENERATE_SHAPER_GRAPHS macro and type the values into `variable_shaper_*_freq` and `variable_shaper_*_type manually`."

[gcode_shell_command generate_shaper_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-shaper-graph.sh
timeout = 120.
verbose = True

[gcode_shell_command generate_tension_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-belt-tension-graph.sh
timeout = 120.
verbose = True

[gcode_macro SET_PRESSURE_ADVANCE]
variable_snyc_toolheads = False
rename_existing = SET_PRESSURE_ADVANCE_BASE
gcode = 
	{% if params.SYNC_TOOLHEADS is defined %}
	{% set snyc_toolheads = true if params.SYNC_TOOLHEADS|default(false)|lower == 'true' else false %}
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=True
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="Syncing toolheads..."
	{% else %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' or snyc_toolheads %}
	{% set advance = params.ADVANCE|default(printer['extruder'].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['extruder'].smooth_time|float)|float %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T0"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T1"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder1' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% else %}
	{% set extruder = 'extruder' if act_t == 0 else 'extruder1' %}
	{% if params.EXTRUDER is defined %}
	{% set extruder = params.EXTRUDER %}
	{% endif %}
	{% if extruder == 'extruder' or extruder == 'extruder1' %}
	{% set advance = params.ADVANCE|default(printer['%s' % extruder].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['%s' % extruder].smooth_time|float)|float %}
	SET_PRESSURE_ADVANCE_BASE EXTRUDER={extruder} ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% if params.EXTRUDER is not defined %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG={"T%s" % act_t}
	{% endif %}
	{% else %}
	SET_PRESSURE_ADVANCE_BASE { rawparams }
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro M106]
rename_existing = M106.1
variable_swap_speed = -1
gcode = 
	
	{% set s = [[params.S|default(255)|int, 255]|min, 0]|max %}
	{% set p = params.P|default(-1)|int %}
	{% set speed = s / 255 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set t = 1 if idex_mode=='primary' else 0 %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(0)|int == 1 else false %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set sync_fans = true %}
	{% endif %}
	
	
	{% if sync_fans and idex_mode != "copy" and idex_mode != "mirror" %}
	
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int %}
	
	
	{% if toolshift_count > total_toolshifts %}
	{% set sync_fans = false %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE=-1
	
	
	{% if p == -1 %}
	
	{% if speed == 0 %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed}
	{% else %}
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE={speed}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={(speed if (t == 0 or sync_fans) else 0)}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={(speed if (t == 1 or sync_fans) else 0)}
	{% endif %}
	{% else %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed if t == p else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed if t == p else 0}
	{% endif %}
	
	
	M106.1 S{s}

[gcode_macro M107]
rename_existing = M107.1
gcode = 
	{% set p = params.P|default(-1)|int %}
	M106 S0 P{p}

[gcode_macro _SELECT_TOOL]
variable_last_timestamp = 0
gcode = 
	{% if params.T is defined %}
	{% set idex_mode = '' %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if "xyz" not in printer.toolhead.homed_axes and (idex_mode == "copy" or idex_mode == "mirror") %}
	_IDEX_SINGLE
	{% set idex_mode = 'reset' %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set new_t = params.T|int %}
	
	
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads and is_printing_gcode %}
	{% set new_t = 0 if new_t == 1 else 1 %}
	{% endif %}
	
	
	{% set toolchange_prepurging_timer = printer["gcode_macro RatOS"].toolchange_prepurging_timer|default(0)|int %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	DEBUG_ECHO PREFIX="_SELECT_TOOL" MSG="act_t: {act_t}, new_t: {new_t}, is_printing_gcode: {is_printing_gcode}, swap_toolheads: {swap_toolheads}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	{% set act_extruder = 'extruder%s' % ('' if new_t == 0 else new_t) %}
	{% if new_t != act_t or printer.toolhead.extruder != act_extruder or idex_mode == 'reset' %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Selecting T{new_t}.."
	
	
	M220 S100
	
	
	
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(1)|int == 1 else false %}
	
	
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set toolshift = false %}
	{% endif %}
	
	
	{% set fan_speed = printer["fan_generic part_fan_t%s" % act_t].speed %}
	
	
	{% set deactivate_toolhead = false %}
	{% if is_printing_gcode %}
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int + 1 %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE={toolshift_count}
	{% if toolshift_count == total_toolshifts %}
	{% set deactivate_toolhead = true %}
	{% endif %}
	{% endif %}
	
	
	{% set needs_wakeup = true if printer["gcode_macro T%s" % new_t].standby|default(false)|lower == 'true' else false %}
	
	
	{% set needs_purging = false %}
	{% set wake_up_purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% if is_printing_gcode and toolchange_prepurging_timer > 0 and wake_up_purge > 0 %}
	{% set new_timestamp = printer["print_stats"].print_duration %}
	{% set elapsed_time = new_timestamp - last_timestamp %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={new_timestamp}
	{% if elapsed_time > toolchange_prepurging_timer %}
	{% set needs_purging = true %}
	{% endif %}
	{% endif %}
	
	
	{% set first_use_purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% if toolshift_count == 1 and first_use_purge > 0 %}
	{% set needs_purging = true %}
	{% endif %}
	
	
	{% if is_printing_gcode and (toolchange_standby_temp > -1 or needs_purging or needs_wakeup) %}
	_TOOLHEAD_STANDBY TOOLHEAD={act_t}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	_TOOLHEAD_WAKEUP TOOLHEAD={new_t} X={new_x} Y={new_y} Z={new_z} FAN_SPEED={fan_speed} TOOLSHIFT_COUNT={toolshift_count}
	{% else %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(false)|lower == 'true' else false %}
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if (new_t == 0 or sync_fans) else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if (new_t == 1 or sync_fans) else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	_TOOLCHANGE T={new_t} X={new_x} Y={new_y} Z={new_z} PARK_T0={park_t0} PARK_T1={park_t1} TOOLSHIFT={toolshift}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[new_t]|float)} SHAPER_FREQ_Y={(shaper_y_freq[new_t]|float)} SHAPER_TYPE_X={(shaper_x_type[new_t]|lower)} SHAPER_TYPE_Y={(shaper_y_type[new_t]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if new_t == 0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if new_t == 1 else False}
	
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% set sanity_check_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if new_t == 0 %}
	{% if printer.toolhead.extruder == 'extruder' %}
	{% if sanity_check_idex_mode == 'primary' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% elif new_t == 1 %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% if sanity_check_idex_mode == 'inactive' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _TOOLHEAD_STANDBY]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Putting toolhead T{toolhead} into standby mode."
	DEBUG_ECHO PREFIX="_TOOLHEAD_STANDBY" MSG="toolhead: {toolhead}, config_z_hop: {config_z_hop}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={toolhead} SYNC=0
	PARK_TOOLHEAD
	
	
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={toolchange_standby_temp}
	{% endif %}
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=True
	{% endif %}
	
	
	_LED_TOOLHEAD_STANDBY TOOLHEAD={toolhead}

[gcode_macro _TOOLHEAD_WAKEUP]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set fan_speed = params.FAN_SPEED|float %}
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift_count = params.TOOLSHIFT_COUNT|default(0)|int %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% if toolshift_count == 1 %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% endif %}
	{% set needs_wakeup = true if printer["gcode_macro T%s" % toolhead].standby|default(false)|lower == 'true' else false %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Waking up toolhead T{toolhead}. Please wait for extruder to heat up..."
	DEBUG_ECHO PREFIX="_TOOLHEAD_WAKEUP" MSG="toolhead: {toolhead}, fan_speed: {fan_speed}, new_x: {new_x}, new_y: {new_y}, new_z: {new_z}, config_z_hop: {config_z_hop}"
	
	
	_LED_TOOLHEAD_WAKEUP TOOLHEAD={toolhead}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={toolhead} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE=1
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if toolhead == 0 else toolhead}
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if needs_wakeup %}
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set temp = extruder_first_layer_temp[toolhead]|float %}
	{% else %}
	{% set temp = extruder_other_layer_temp[toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if toolhead == 0 else 'extruder1'} MINIMUM={temp}  MAXIMUM={temp + 5}
	{% endif %}
	
	
	_LED_PRINTING TOOLHEAD={toolhead}
	
	
	{% if purge > 0 %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={toolhead} E={purge}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	
	
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if toolhead == 1 else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	G92 E0
	G1 E-{e} F{feedrate}
	G92 E0
	
	
	{% if new_x >= 0 and new_y >= 0 %}
	G1 X{new_x} Y{new_y} F{speed}
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={config_z_hop} T={toolhead} SYNC=0
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=False

[gcode_macro _TOOLCHANGE]
variable_toolshift_count = 0
gcode = 
	
	
	{% set new_t = params.T|default(-1)|int %}
	{% set new_x = params.X|default(-1.0)|float %}
	{% set new_y = params.Y|default(-1.0)|float %}
	{% set new_z = params.Z|default(-1.0)|float %}
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(true)|lower == 'true' else false %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T: {new_t}, X: {new_x}, Y: {new_y}, Z: {new_z}, PARK_T0: {park_t0}, PARK_T1: {park_t1}, IS_PRINTING_GCODE: {is_printing_gcode}, TOOLSHIFT: {toolshift}"
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	{% if park_t0 >= 0 and park_t1 >= 0 %}
	{% set parking_position_t0 = park_t0 %}
	{% set parking_position_t1 = park_t1 %}
	{% set parking_position_act_t = park_t0 if act_t == 0 else park_t1 %}
	{% endif %}
	
	
	{% if not is_printing_gcode and not toolshift %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Changing tool to T{new_t} without retracting/extruding or moving the toolheads except for parking."
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	G90
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% if not is_printing_gcode and toolshift and new_x < 0 and new_y < 0 %}
	{% set new_x = center_x %}
	{% set new_y = printer.gcode_move.gcode_position.y|float %}
	{% endif %}
	
	{% if new_x < 0 or new_y < 0 %}
	
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="No new X or Y position given, parking the active toolhead and activating the new toolhead without moving it."
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={new_t}
	
	
	{% if "x" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	{% if is_printing_gcode %}
	_EXTRUDE T={new_t}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	{% if "xyz" not in printer.toolhead.homed_axes %}
	
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	
	
	{% set svv = printer.save_variables.variables %}
	{% if new_t == default_toolhead %}
	{% set new_xoffset = 0 %}
	{% set new_yoffset = 0 %}
	{% set new_zoffset = 0 %}
	{% else %}
	{% set new_xoffset = -svv.idex_xoffset %}
	{% set new_yoffset = -svv.idex_yoffset %}
	{% set new_zoffset = -svv.idex_zoffset %}
	{% endif %}
	
	{% set xoffset_correction = new_xoffset - printer.named_offsets.toolhead_alignment.x %}
	{% set yoffset_correction = new_yoffset - printer.named_offsets.toolhead_alignment.y %}
	{% set zoffset_correction = new_zoffset - printer.named_offsets.toolhead_alignment.z %}
	
	{% if new_t == 0 %}
	
	{% set t0_act_x = parking_position_t0 %}
	{% set t1_act_x = printer.toolhead.position.x|float %}
	{% set t0_new_x = new_x %}
	{% set t1_new_x = parking_position_t1 %}
	{% set t0_distance = t0_new_x - t0_act_x %}
	{% set t1_distance = t1_new_x - t1_act_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T0."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	
	
	G1 X{t0_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x + (t1_new_x - t1_act_x)} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t0_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T0: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% elif new_t == 1 %}
	
	{% set t0_act_x = printer.toolhead.position.x|float %}
	{% set t1_act_x = parking_position_t1 %}
	{% set t0_new_x = parking_position_t0 %}
	{% set t1_new_x = new_x %}
	{% set t0_distance = t0_act_x - t0_new_x %}
	{% set t1_distance = t1_act_x - t1_new_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T1."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x - t1_distance + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t1_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T1: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% endif %}
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	{% endif %}

[gcode_macro _ZHOP_BEFORE_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_hop = params.Z_HOP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_HOP: {z_hop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="COMBINED_ZHOP G1 Z+{z_hop} E-{e} F{speed * 60}"
	G1 Z+{z_hop} E-{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="ZHOP G1 Z+{z_hop} F{speed * 60}"
	G1 Z+{z_hop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="RETRACT G1 E-{e} F{feedrate}"
	G1 E-{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _ZDROP_AFTER_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_drop = params.Z_DROP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_DROP: {z_drop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="COMBINED_ZDROP G1 Z-{z_drop} E{e} F{speed * 60}"
	G1 Z-{z_drop} E{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="ZDROP G1 Z-{z_drop} F{speed * 60}"
	G1 Z-{z_drop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="EXTRUDE G1 E{e} F{feedrate}"
	G1 E{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _EXTRUDE]
gcode = 
	
	{% set t = params.T|int %}
	
	
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	
	DEBUG_ECHO PREFIX="_EXTRUDE" MSG="G1 E{e} F{feedrate * 60}"
	
	
	G91
	M82
	G92 E0
	G1 E{e} F{feedrate * 60}
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _DEACTIVATE_TOOLHEAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_DEACTIVATE_TOOLHEAD" MSG="TOOLHEAD {toolhead}"
	
	
	{% if toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% endif %}
	
	
	M106.1 S0
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={toolhead}

[delayed_gcode _INIT_TOOLHEADS]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	_IDEX_SINGLE INIT=1
	
	
	{% if printer.fastconfig.settings.dual_carriage.safe_distance is defined %}
	{% if printer.fastconfig.settings.dual_carriage.safe_distance|float < 50 %}
	{ action_emergency_stop("Dual carriage safe_distance seems to be too low!") }
	{% endif %}
	{% else %}
	{ action_emergency_stop("Dual carriage safe_distance not defined!") }
	{% endif %}

[gcode_macro _SET_TOOLHEAD_OFFSET]
description = "Internal use only. Sets the toolhead_alignment offset (and hotend_thermal_expansion offset when configured) for the active/dominant toolhead."
gcode = 
	
	{% set move = params.MOVE|default(0)|int %}
	{% set force_toolhead = params.FORCE_TOOLHEAD|default(-1)|int %}
	
	
	{% if params.T is defined %}
	CONSOLE_ECHO TYPE="error" MSG="_SET_TOOLHEAD_OFFSET called with deprectated T parameter, which is ignored."
	{';$_SET_TOOLHEAD_OFFSET_ignoring_TOOLHEAD_parameter'}
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="active/dominant toolhead: {toolhead}, MOVE: {move}, FORCE_TOOLHEAD: {force_toolhead}"
	
	
	{% if force_toolhead >= 0 %}
	{% set toolhead = force_toolhead %}
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="FORCE_TOOLHEAD applied, using TOOLHEAD: {toolhead}"
	{% endif %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set move = 0 %}
	{% endif %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|int %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X=0 Y=0 MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z=0 MOVE={move} SPEED={z_speed}
	{% else %}
	{% set svv = printer.save_variables.variables %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X={(-svv.idex_xoffset)} Y={(-svv.idex_yoffset)} MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-svv.idex_zoffset)} MOVE={move} SPEED={z_speed}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}

[gcode_macro TOOLSHIFT_CONFIG]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={params.SPEED|default(300)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={params.ACCEL|default(5000)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_retraction VALUE={params.RETRACT|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_extrusion VALUE={params.EXTRUDE|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_feedrate VALUE={params.FEEDRATE|default(7200)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={params.Z_HOP|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zspeed VALUE={params.Z_SPEED|default(25)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_combined_zhop VALUE={true if params.COMBINED_ZHOP|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_sync_fans VALUE={true if params.SYNC_FANS|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_prepurging_timer VALUE={params.AUTO_PURGE_TIME|default(0)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_purge VALUE={params.PURGE|default(25)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_standby_temp VALUE={params.STANDBY_TEMP|default(-1)|float}

[gcode_macro CALCULATE_DC_ENDSTOP]
description = "DEPRECATED: This macro has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."
gcode = 
	CONSOLE_ECHO TITLE="CALCULATE_DC_ENDSTOP has been deprecated" TYPE="error" MSG="The CALCULATE_DC_ENDSTOP has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."

[gcode_macro _VAOC]
variable_is_fixed = True
variable_is_started = False
variable_is_started_at_temp = False
variable_additional_safe_distance = 50
variable_safe_z = 30
variable_auto_z_offset_calibration = True
variable_enable_camera_cooling = True
variable_camera_cooling_fan_speed = 0.3
variable_camera_cooling_temperature = 50
variable_toolchange_travel_speed = 300
variable_toolchange_travel_accel = 5000
variable_adjusting_secondary_toolhead_focus_adjusts_zoffset = False
variable_cache_toolchange_travel_speed = 300
variable_cache_toolchange_travel_accel = 5000
variable_cache_toolchange_zhop = 1.0
variable_t0_toolhead_sensor_enabled = 0
variable_t1_toolhead_sensor_enabled = 0
variable_t0_bowden_sensor_enabled = 0
variable_t1_bowden_sensor_enabled = 0
variable_loaded_skew_profile = ""
variable_gcode_z_offset = 0.0
variable_start_x_offset = 0.0
variable_start_y_offset = 0.0
gcode = 
	_ECHO_VAOC_VARS
variable_expected_camera_x_position = 212.5
variable_expected_camera_y_position = 530.5

[gcode_macro _VAOC_START]
description = Called from the front end. If T0_TEMP, T1_TEMP and BED_TEMP parameter are specified, VAOC calibration will start under real conditions at printing temp.
gcode = 
	
	{% set t0_temp = params.T0_TEMP|default(0)|int %}
	{% set t1_temp = params.T1_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(0)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro SKEW_PROFILE"].loaded_profile|default("") %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=loaded_skew_profile VALUE='"{loaded_skew_profile}"'
	
	
	{% if t0_temp > 0 and t1_temp > 0 and bed_temp > 0 %}
	
	
	{% if not is_fixed %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("VAOC calibration at temp works only with a fixed installed VAOC device.") }
	{% endif %}
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE=0
	{% endif %}
	
	
	START_PRINT EXTRUDER_TEMP={t0_temp},{t1_temp} EXTRUDER_OTHER_LAYER_TEMP={t0_temp},{t1_temp} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp} INITIAL_TOOL=0 TOTAL_LAYER_COUNT=1 X0={(printable_x_max / 2 - 10)} Y0={(printable_y_max / 2 - 10)} X1={(printable_x_max / 2 + 10)} Y1={(printable_y_max / 2 + 10)} TOTAL_TOOLSHIFTS=1 FIRST_X={printable_x_max / 2} FIRST_Y={printable_y_max / 2} MIN_X={(printable_x_max / 2 - 10)} MAX_X={(printable_x_max / 2 + 10)} USED_TOOLS=0,1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=True
	
	{% endif %}
	
	
	_START_VAOC

[gcode_macro _START_VAOC]
description = Called from _VAOC_START. Do not call it manually.
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(printable_x_max/2)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(printable_y_max/2)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	DEBUG_ECHO PREFIX="VAOC_START" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, zcontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_x_offset VALUE={svv.idex_xoffset|default(0.0)|float}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_y_offset VALUE={svv.idex_yoffset|default(0.0)|float}
	
	
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_SAFE_Z_HEIGHT
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_speed VALUE={printer["gcode_macro RatOS"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_accel VALUE={printer["gcode_macro RatOS"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_zhop VALUE={printer["gcode_macro RatOS"].toolchange_zhop|float}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE=0
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"START X_REFERENCE:%.6f Y_REFERENCE:%.6f Z_REFERENCE:%.6f PARK_T0:%.6f PARK_T1:%.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, parking_position_t0, parking_position_t1)}
	
	
	_LED_VAOC_ON
	
	
	
	
	
	
	
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=gcode_z_offset VALUE={printer.gcode_move.homing_origin.z}
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z=0
	
	
	MAYBE_HOME
	M400
	
	
	_LOAD_RATOS_SKEW_PROFILE
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	IDEX_SINGLE
	{% endif %}
	
	
	
	SAVE_GCODE_STATE NAME=vaoc_state
	
	
	RESET_NAMED_OFFSET EVENT=reset_all
	
	
	{% if is_fixed %}
	_SELECT_TOOL T=0 TOOLSHIFT=false
	{% if default_toolhead == 0 %}
	G1 X{idex_xcontrolpoint} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint + safe_distance + additional_safe_distance} F{speed}
	{% else %}
	G1 X{idex_xcontrolpoint - safe_distance - additional_safe_distance} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint} F{speed}
	{% endif %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	{% else %}
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	G1 X{idex_xcontrolpoint} F{speed}
	G1 Y{idex_ycontrolpoint} F{speed}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	
	
	_SELECT_TOOL T={default_toolhead} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	{% if not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={default_toolhead}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=True

[gcode_macro _VAOC_END]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_y = printable_y_max / 2 %}
	{% set saved_gcode_z_offset = printer["gcode_macro _VAOC"].gcode_z_offset|default(0.0)|float %}
	
	DEBUG_ECHO PREFIX="_VAOC_END" MSG="printable_y_max: {printable_y_max}, center_y: {center_y}, safe_z: {safe_z}"
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% set x_offset_change = svv.idex_xoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_x_offset|default(0.0)|float %}
	{% set y_offset_change = svv.idex_yoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_y_offset|default(0.0)|float %}
	{% set offset_change_norm = (x_offset_change ** 2 + y_offset_change ** 2) ** 0.5 %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="VAOC calibration changed the relative XY offset between T0 and T1 by {offset_change_norm|round(3)} mm (ΔX: {x_offset_change|round(3)}, ΔY: {y_offset_change|round(3)})"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	G1 Y{center_y} F{speed}
	
	
	_IDEX_SINGLE INIT=1
	
	
	_LED_VAOC_OFF
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={printer["gcode_macro _VAOC"].cache_toolchange_zhop|float}
	
	
	{% if printer["gcode_macro _VAOC"].is_started_at_temp|default(true)|lower == 'true' %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_bowden_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_bowden_sensor_enabled|int}
	{% endif %}
	{% endif %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro _VAOC"].loaded_skew_profile|default("") %}
	{% if loaded_skew_profile != "" %}
	SKEW_PROFILE LOAD={loaded_skew_profile}
	{% else %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=vaoc_state
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z={saved_gcode_z_offset}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False

[gcode_macro _VAOC_LOAD_TOOL]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set auto_temp_offset = true if params.AUTO_TEMP_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set toolhead_zoffset = svv.idex_zoffset|default(0)|float %}
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move T%s to control point: X%.6f Y%.6f Z%.6f IS_FIXED=%s"' % (t, idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, is_fixed)}
	
	
	{% if not auto_temp_offset and not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={t}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	{% set current_z = printer.toolhead.position.z|float %}
	{% set lowest_toolhead_z = [current_z, current_z - toolhead_zoffset]|min %}
	{% if lowest_toolhead_z < safe_z %}
	G1 Z{[safe_z, safe_z + toolhead_zoffset]|max} F{z_speed}
	{% else %}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	{% endif %}
	
	
	_SELECT_TOOL T={t} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_SET_CAMERA_COOLING]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	
	
	{% set enable_camera_cooling = true if printer["gcode_macro _VAOC"].enable_camera_cooling|default(true)|lower == 'true' else false %}
	{% set camera_cooling_temperature = printer["gcode_macro _VAOC"].camera_cooling_temperature|float %}
	{% set camera_cooling_fan_speed = printer["gcode_macro _VAOC"].camera_cooling_fan_speed|float %}
	
	
	{% if printer.heater_bed.temperature >= camera_cooling_temperature and enable_camera_cooling %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={camera_cooling_fan_speed if t == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={camera_cooling_fan_speed if t == 1 else 0}
	
	
	M106.1 S{camera_cooling_fan_speed}
	
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	{% endif %}

[gcode_macro _VAOC_SET_TOOL]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="_VAOC_SET_TOOL" MSG="IDEX_MODE: {idex_mode}, TOOLHEAD: {toolhead}"
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	{% set x = printer.gcode_move.gcode_position.x|float %}
	{% set y = printer.gcode_move.gcode_position.y|float %}
	{% set z = printer.gcode_move.gcode_position.z|float %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE={x}
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE={y}
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE={z}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Control point was set: X%.6f Y%.6f Z%.6f"' % (x, y, z)}
	
	{% else %}
	
	
	
	{% set move_diff_x = printer.gcode_move.gcode_position.x|float - svv.idex_xcontrolpoint|float %}
	{% set move_diff_y = printer.gcode_move.gcode_position.y|float - svv.idex_ycontrolpoint|float %}
	{% set move_diff_z = printer.gcode_move.gcode_position.z|float - svv.idex_zcontrolpoint|float %}
	
	
	{% set new_x_offset = svv.idex_xoffset - move_diff_x %}
	{% set new_y_offset = svv.idex_yoffset - move_diff_y %}
	{% set new_z_offset = svv.idex_zoffset - move_diff_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE={new_x_offset}
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE={new_y_offset}
	
	{% set z_focus_msg = "" %}
	{% if move_diff_z|abs > 1e-6 %}
	{% if printer["gcode_macro _VAOC"].adjusting_secondary_toolhead_focus_adjusts_zoffset|default(false)|lower == 'true' %}
	{% set z_focus_msg = " (Z offset adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={new_z_offset}
	{% else %}
	{% set z_focus_msg = " (Z offset not adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	{% set new_z_offset = svv.idex_zoffset %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset was set: X%.6f Y%.6f Z%.6f%s"' % (toolhead, new_x_offset, new_y_offset, new_z_offset, z_focus_msg)}
	
	{% endif %}

[gcode_macro _VAOC_MOVE]
gcode = 
	
	{% set x = params.X|default(0)|float %}
	{% set y = params.Y|default(0)|float %}
	{% set z = params.Z|default(0)|float %}
	
	
	G91
	{% if z != 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 Z%.6f F300"' % (z)}
	G1 Z{z} F300
	
	{% else %}
	{% if x <=2 and y <=2 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 X%.6f Y%.6f F18000"' % (x, y)}
	G1 X{x} Y{y} F18000
	{% endif %}
	{% endif %}
	G90

[gcode_macro _VAOC_CALIBRATE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	{% if printer["z_offset_probe"] is defined and is_started %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	
	{% if auto_z_offset %}
	_START_VAOC AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_END
	{% else %}
	_VAOC_LOAD_TOOL T={default_toolhead}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	{% endif %}
	
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_Z_OFFSET
	
	{% endif %}

[gcode_macro _VAOC_PROBE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}
	{% if not auto_z_offset %}
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	{% endif %}
	M400
	_VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT

[gcode_macro _VAOC_Z_OFFSET_PROBE_CURRENT_POSITION]
gcode = 
	
	Z_OFFSET_PROBE PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_DROP=1 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median

[gcode_macro _VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT]
gcode = 
	{% if printer["z_offset_probe"] is defined %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE={last_z}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Z-offset control point set:: %.6f"' % last_z}
	
	{% else %}
	
	
	
	{% set z = svv.idex_zoffsetcontrolpoint|float - last_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={z}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-z)}
	
	
	G0 Z{svv.idex_zcontrolpoint|float} F{z_speed}
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset set: Z %.6f"' % (t, z)}
	
	{% endif %}
	
	{% endif %}

[gcode_macro _VAOC_ECHO_Z_OFFSET]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s toolhead z-offset %.6f"' % (1 if default_toolhead == 0 else 0, svv.idex_zoffset)}
	{% if svv.idex_zoffset|abs < 0.02 %}
	CONSOLE_ECHO TITLE={'"Perfect toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="You have a perfect toolhead z-offset!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.02 and svv.idex_zoffset|abs < 0.05 %}
	CONSOLE_ECHO TITLE={'"Good toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is good!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.05 and svv.idex_zoffset|abs < 0.1 %}
	CONSOLE_ECHO TITLE={'"High toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset could be better._N_Use minimum 0.3mm first layer height for copy and mirror mode prints." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.1 and svv.idex_zoffset|abs < 0.2 %}
	CONSOLE_ECHO TITLE={'"Bad toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is bad._N_Copy and mirror mode prints are not recommended with it." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.2 %}
	CONSOLE_ECHO TITLE={'"Unacceptable toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is unacceptable._N_Do not print in copy and mirror mode with it." TYPE="alert"
	{% endif %}
	RATOS_ECHO PREFIX="VAOC" MSG="Toolhead z-offset calibration done!"

[gcode_macro _VAOC_CALIBRATE_TEMP_OFFSET]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if is_fixed and is_started and printer["z_offset_probe"] is defined and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	_VAOC_LOAD_TOOL T={default_toolhead} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_NOZZLE_TEMP_OFFSETS
	
	{% endif %}

[gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET=0
	
	
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	M400

[gcode_macro _VAOC_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(150)|float %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Probing with nozzle temperature {temp}°C..."
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	
	
	G0 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _VAOC_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set msg = '"T0 expansion coefficient %.6fmm_N_T1 expansion coefficient %.6fmm"' % (svv.nozzle_expansion_coefficient_t0, svv.nozzle_expansion_coefficient_t1) %}
	CONSOLE_ECHO TITLE="Nozzle expansion coefficients:" MSG={msg} TYPE="success"

[gcode_macro _VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - expected_camera_x_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC x-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_xcontrolpoint, expected_camera_x_position)) }
	{% endif %}
	{% if (idex_ycontrolpoint - expected_camera_y_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC y-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_ycontrolpoint, expected_camera_y_position)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - printer.gcode_move.gcode_position.x|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected y-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_xcontrolpoint, printer.gcode_move.gcode_position.x|float)) }
	{% endif %}
	{% if (idex_ycontrolpoint - printer.gcode_move.gcode_position.y|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected x-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_ycontrolpoint, printer.gcode_move.gcode_position.y|float)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_SAFE_Z_HEIGHT]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set idex_zoffsetcontrolpoint = svv.idex_zoffsetcontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_SAFE_Z_HEIGHT" MSG={'"idex_zcontrolpoint: %.6f, idex_zoffsetcontrolpoint: %.6f"' % (idex_zcontrolpoint, idex_zoffsetcontrolpoint)}
	
	{% if safe_z < idex_zcontrolpoint + 2 or safe_z < idex_zoffsetcontrolpoint + 2 %}
	{action_raise_error("VAOC safe_z value (%.3f) is too low, it must be higher than %.3f" % (safe_z, [idex_zoffsetcontrolpoint + 2, idex_zcontrolpoint + 2]|max))}
	{% endif %}

[gcode_macro _VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED]
gcode = 
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T0. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T1. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_RESET]
gcode = 
	DEBUG_ECHO PREFIX="_VAOC_RESET" MSG="running template-emitted _VAOC_RESET macro"
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE=212.5
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE=530.5
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE=10
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE=0
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE=0.0
	
	RESET_DC_ENDSTOP_CONFIGURATION
	RESET_Y_MAX_ADJUSTMENT
	
	
	CONSOLE_ECHO TITLE="VAOC Configuration Reset" MSG="VAOC configuration has been reset. You must RESTART klipper for the changes to take effect,_N_then re-calibrate VAOC."

[gcode_macro _ECHO_VAOC_VARS]
description = Echo VAOC variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro _VAOC"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro _VAOC_SWITCH_LED]
gcode = 
	{% if params.STATE|default(0)|int == 1 %}
	_LED_VAOC_ON
	{% else %}
	_LED_VAOC_OFF
	{% endif %}

[gcode_macro Z_PROBE_TEST_T0]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T0
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST_T1]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T1
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	
	
	_VAOC_Z_PROBE_TEST_EVALUATE
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro _VAOC_Z_PROBE_LOOP]
gcode = 
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_SHAKE_IT
	_VAOC_START

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if primary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T0. Retried {primary_retries} time(s)."
	{% endif %}
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	
	{% if (primary_range - secondary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 is drifting significantly more than T1."
	{% endif %}
	{% if (secondary_range - primary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 is drifting significantly more than T0."
	{% endif %}
	
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T0]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T1]
gcode = 
	
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _SHAKE_IT]
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	_Z_HOP
	{% for i in range(3) %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 + 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 + 1}
	{% endfor %}
	{% for i in range(2) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 + 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 + 50}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 1}
	{% endfor %}
	{% endfor %}

[gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 retries updated: {new_retries}"

[gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 retries updated: {new_retries}"

[gcode_macro _CLEAR_PRIMARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _CLEAR_SECONDARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _VAOC_TEST_Z_OFFSET]
gcode = 
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}

[delayed_gcode _IDEX_INIT]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	VERIFY_HYBRID_INVERTED

[gcode_macro Z_TILT_ADJUST]
rename_existing = Z_TILT_ADJUST_ORIG
gcode = 
	
	{% set beacon_contact_z_tilt_adjust_samples = printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust_samples|default(2)|int %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(true)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	_IDEX_SINGLE
	
	_SELECT_TOOL T={printer["gcode_macro RatOS"].default_toolhead|default(0)|int} TOOLSHIFT=false
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_tilt_adjust %}
	Z_TILT_ADJUST_ORIG PROBE_METHOD=contact SAMPLES={beacon_contact_z_tilt_adjust_samples}
	{% else %}
	Z_TILT_ADJUST_ORIG
	{% endif %}
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if idex_mode == "copy" %}
	_IDEX_COPY
	{% elif idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[stepper_x]
position_max = 500
position_endstop = -59.6
position_min = -59.6
step_pin = PF13
dir_pin = x_dir_pin
enable_pin = !PF14
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t0:PA2

[stepper_y]
position_max = 533.65
position_min = -14.35
position_endstop = -14.35
step_pin = PG0
dir_pin = !y_dir_pin
enable_pin = !PF15
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = PG9

[stepper_z]
position_max = 500
position_min = -7
step_pin = PC13
dir_pin = !z0_dir_pin
enable_pin = !PF1
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4
homing_speed = 10
endstop_pin = probe:z_virtual_endstop

[z_tilt]
z_positions = 
	0,0
	250,500
	500,0
points = 
	20, 10
	480, 230
	20, 450
horizontal_move_z = 20
retries = 10
retry_tolerance = 0.02
speed = 600

[extruder]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t0:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t0:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t0:PD3
dir_pin = toolboard_t0:e_dir_pin
enable_pin = !toolboard_t0:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[firmware_retraction]
retract_speed = 60
unretract_extra_length = 0
unretract_speed = 60
retract_length = 0.2

[extruder1]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t1:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t1:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t1:PD3
dir_pin = toolboard_t1:e_dir_pin
enable_pin = !toolboard_t1:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[resonance_tester]
accel_chip_x = lis2dw toolboard_t0
accel_chip_y = lis2dw toolboard_t0
probe_points = 
	250,250,20

[tmc5160 stepper_x]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC4
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 dual_carriage]
stealthchop_threshold = 0
interpolate = True
cs_pin = PF2
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y]
stealthchop_threshold = 0
interpolate = True
cs_pin = PD11
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y1]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC7
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[stepper_y1]
step_pin = PG4
dir_pin = y1_dir_pin
enable_pin = !PA2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46

[tmc2209 stepper_z]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE4
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[tmc2209 stepper_z1]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE1
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z1]
step_pin = PE2
dir_pin = !z1_dir_pin
enable_pin = !PD4
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 stepper_z2]
stealthchop_threshold = 0
interpolate = True
uart_pin = PD3
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z2]
step_pin = PE6
dir_pin = !z2_dir_pin
enable_pin = !PE0
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 extruder]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t0:PB3
run_current = 0.707
sense_resistor = 0.11

[tmc2209 extruder1]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t1:PB3
run_current = 0.707
sense_resistor = 0.11

[beacon]
serial = /dev/beacon
x_offset = 0
y_offset = 27.5
mesh_main_direction = x
mesh_runs = 1
mesh_cluster_size = 0
speed = 15.
lift_speed = 80.
contact_max_hotend_temperature = 275
contact_mesh_min = 20,20
contact_mesh_max = 480,480

[beacon_user_z_offset]

[beacon_mesh]

[beacon_true_zero_correction]

[beacon_adaptive_heat_soak]

[delayed_gcode _BEACON_INIT]
initial_duration = 1
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	_BEACON_MESH_INIT
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_coefficient_multiplier
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_applied_offset
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=beacon_saved_runtime_offset
	{% if printer["gcode_macro RatOS"].beacon_contact_expansion_multiplier is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_contact_expansion_multiplier is no longer used, please remove it from your config file."
	{% endif %}
	{% if printer["gcode_macro RatOS"].beacon_scan_compensation_resolution is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_scan_compensation_resolution is no longer used, please remove it from your config file."
	{% endif %}

[gcode_macro BEACON_RATOS_CALIBRATION]
gcode = 
	RATOS_ECHO MSG="Did you mean BEACON_RATOS_CALIBRATE?"

[gcode_macro BEACON_RATOS_CALIBRATE]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	BEACON_INITIAL_CALIBRATION _AUTOMATED=True
	
	{% if beacon_contact_start_print_true_zero %}
	BEACON_POKE_TEST _AUTOMATED=True
	_BEACON_CHECK_POKE
	{% if printer["dual_carriage"] is not defined %}
	BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET _AUTOMATED=True
	{% endif %}
	{% endif %}
	
	{% set already_heated = False %}
	
	
	{% if beacon_contact_start_print_true_zero and beacon_scan_compensation_enable %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% set already_heated = True %}
	{% endif %}
	
	
	BEACON_FINAL_CALIBRATION _AUTOMATED=True _AUTOMATED_ALREADY_HEATED={already_heated} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	{% if beacon_contact_start_print_true_zero %}
	{% if printer["dual_carriage"] is not defined %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	_BEACON_ECHO_POKE
	{% endif %}
	RATOS_ECHO MSG="Beacon calibration finished!"
	
	
	_LED_BEACON_CALIBRATION_END
	
	
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG

[gcode_macro BEACON_INITIAL_CALIBRATION]
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Initial beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro BEACON_FINAL_CALIBRATION]
description = Runs BEACON_AUTO_CALIBRATE after heating the bed and chamber to specified temperatures. This creates a beacon model under reference conditions for future use.
	This macro will skip calibration if both the beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero settings are enabled, because a new
	model will be calibrated automatically at the start of each print. Use FORCE=True to override this check.
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set already_heated = true if params._AUTOMATED_ALREADY_HEATED|default(false)|lower == 'true' else false %}
	{% set force = params.FORCE|default('false')|lower in ('1', 'true', 'yes') %}
	
	
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default('false')|lower == "true" %}
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero and not force %}
	RATOS_ECHO MSG="BEACON_FINAL_CALIBRATION skipped, not needed because beacon_contact_calibrate_model_on_true_zero is enabled. Use FORCE=True to override."
	{% else %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	{% if chamber_temp > 0 and not already_heated %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	{% if not already_heated %}
	
	G0 Z2.5 F{z_hop_speed}
	
	
	RATOS_ECHO MSG="Waiting for calibration temperature..."
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	{% if beacon_adaptive_heat_soak %}
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,3600]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_Z_HOP
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Final beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	{% endif %}

[gcode_macro BEACON_POKE_TEST]
variable_poke_result_1 = -1
variable_poke_result_2 = -1
variable_poke_result_3 = -1
variable_poke_result_4 = -1
variable_poke_result_5 = -1
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_1 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_2 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_3 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_4 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_5 VALUE=-1
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G0 Z5 F{z_hop_speed}
	
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=1
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=2
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=3
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=4
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=5
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Beacon poke test finished!"
	{% if not automated %}
	_BEACON_ECHO_POKE
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro _BEACON_PROBE_POKE]
gcode = 
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	BEACON_POKE speed=3 top=5 bottom={poke_bottom}
	BEACON_QUERY

[gcode_macro _BEACON_STORE_POKE]
gcode = 
	
	{% set i = params.I|default(1)|int %}
	
	
	{% set last_z = printer.beacon.last_poke_result|default(0)|float %}
	
	
	{% if printer.beacon.last_poke_result|lower != "none" %}
	{% if printer.beacon.last_poke_result.error == 0 %}
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE={"poke_result_%s" % i} VALUE={printer.beacon.last_poke_result.latency}
	{% endif %}
	{% endif %}

[gcode_macro _BEACON_CHECK_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% if p1 == -1 or p2 == -1 or p3 == -1 or p4 == -1 or p5 == -1 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test error!") }
	{% endif %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	{% if avg > 6 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test failed!") }
	{% endif %}

[gcode_macro _BEACON_ECHO_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	
	
	{% if avg <= 1 %}
	{% set type = "success" %}
	{% set note = "Extremely low noise, rarely achieved" %}
	{% elif avg > 1 and avg <= 4 %}
	{% set type = "info" %}
	{% set note = "Excellent performance for a typical printer" %}
	{% elif avg > 4 and avg <= 8 %}
	{% set type = "warning" %}
	{% set note = "Acceptable performance, machine may have considerable cyclic axis noise" %}
	{% elif avg > 8 and avg <= 11 %}
	{% set type = "alert" %}
	{% set note = "Not ideal, may want to verify proper mounting or use thinner stackups" %}
	{% elif avg > 11 %}
	{% set type = "alert" %}
	{% set note = "Reason for concern, present setup may be risky to continue with" %}
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon poke test result:" TYPE={type} MSG={'"Average latency: %.2f_N_%s"' % (avg, note)}

[gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Nozzle temperature offset calibration..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET=0
	
	
	{% if not automated %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing with nozzle temperature {temp}°C..."
	PROBE PROBE_METHOD=contact PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median
	BEACON_QUERY
	
	
	G0 Z5 F{z_speed}

[gcode_macro _BEACON_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer.beacon.last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{default_toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% if default_toolhead == 0 %}
	CONSOLE_ECHO TYPE="info" MSG={'"T0 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t0}
	{% else %}
	CONSOLE_ECHO TYPE="info" MSG={'"T1 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t1}
	{% endif %}

[gcode_macro _BEACON_SET_NOZZLE_TEMP_OFFSET]
description = "Set the thermal expansion z offset for the active toolhead based on the current extruder target temperature and thermal expansion coefficient."
gcode = 
	{% if params.RESET is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The RESET parameter is no longer supported and has no effect."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% if params.TOOLHEAD is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The TOOLHEAD parameter is no longer supported and has no effect. The macro now automatically determines the current toolhead."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	{% if beacon_contact_expansion_compensation %}
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set nozzle_expansion_coefficient_t0 = svv.nozzle_expansion_coefficient_t0|default(0)|float %}
	{% if printer["dual_carriage"] is defined %}
	{% set nozzle_expansion_coefficient_t1 = svv.nozzle_expansion_coefficient_t1|default(0)|float %}
	{% endif %}
	
	
	{% set temp = printer['extruder' if toolhead == 0 else 'extruder1'].target|float %}
	
	
	{% set temp_delta = temp - beacon_contact_true_zero_temp %}
	{% set expansion_coefficient = nozzle_expansion_coefficient_t0 if toolhead == 0 else nozzle_expansion_coefficient_t1 %}
	{% set expansion_offset = temp_delta * (expansion_coefficient / 100) %}
	
	
	SET_NAMED_OFFSET NAME=hotend_thermal_expansion Z={expansion_offset} MOVE=1 MOVE_SPEED={z_speed}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG={'"Nozzle expansion offset of %.6fmm applied to T%s"' % (expansion_offset, toolhead)}
	DEBUG_ECHO PREFIX="_BEACON_SET_NOZZLE_TEMP_OFFSET" MSG="toolhead: {toolhead}, coefficient: {expansion_coefficient|round(6)}, temp_delta: {temp_delta|round(1)},  expansion_offset: {expansion_offset|round(6)}"
	
	{% endif %}

[gcode_macro BEACON_MEASURE_BEACON_OFFSET]
variable_needs_compensation = False
variable_reference_z = 0.0
variable_front = 0.0
variable_front_left = 0.0
variable_front_right = 0.0
variable_back = 0.0
variable_back_left = 0.0
variable_back_right = 0.0
variable_right = 0.0
variable_left = 0.0
variable_margin_x = 40
variable_margin_y = 40
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=False
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Measure beacon offset..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="center"
	
	
	G0 X{margin_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_left"
	
	
	G0 X{safe_home_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front"
	
	
	G0 X{(printable_x_max - margin_x)} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_right"
	
	
	G0 X{safe_home_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back"
	
	
	G0 X{margin_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_left"
	
	
	G0 X{margin_x} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="left"
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_BEACON_ECHO_BEACON_OFFSET
	
	
	_LED_BEACON_CALIBRATION_END
	
	{% endif %}

[gcode_macro _BEACON_STORE_BEACON_OFFSET]
gcode = 
	
	{% set location = params.LOCATION|lower %}
	
	
	{% set last_z = printer.beacon.last_offset_result["delta"]|default(0)|float %}
	
	
	{% if location == "center" %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE={location} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_BEACON_OFFSET]
gcode = 
	
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float * 1000 %}
	{% set front_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_left|default(0)|float * 1000 %}
	{% set front = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front|default(0)|float * 1000 %}
	{% set front_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_right|default(0)|float * 1000 %}
	{% set right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].right|default(0)|float * 1000 %}
	{% set back_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_right|default(0)|float * 1000 %}
	{% set back = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back|default(0)|float * 1000 %}
	{% set back_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_left|default(0)|float * 1000 %}
	{% set left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].left|default(0)|float * 1000 %}
	
	{% set line_1 = "Front left:    %.6fμm" % (front_left) %}
	{% set line_2 = "Front center:  %.6fμm" % (front) %}
	{% set line_3 = "Front right:   %.6fμm" % (front_right) %}
	{% set line_4 = "Left center:   %.6fμm" % (left) %}
	{% set line_5 = "Right center:  %.6fμm" % (right) %}
	{% set line_6 = "Back left:     %.6fμm" % (back_left) %}
	{% set line_7 = "Back center:   %.6fμm" % (back) %}
	{% set line_8 = "Back right:    %.6fμm" % (back_right) %}
	
	{% set max_value = [(front_left|abs), (front|abs), (front_right|abs), (left|abs), (right|abs), (back_left|abs), (back|abs), (back_right|abs)]|max %}
	{% if max_value <= 50 %}
	{% set type = "success" %}
	{% set recommendation = "Very low beacon offset: %.6fμm._N_No beacon scan compensation needed." % max_value %}
	{% elif max_value > 50 and max_value <= 100 %}
	{% set type = "info" %}
	{% set recommendation = "Low beacon offset: %.6fμm._N_You may experience first layer inconsistensies, consider beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 100 and max_value <= 150 %}
	{% set type = "warning" %}
	{% set recommendation = "High beacon offset: %.6fμm._N_High chance of first layer problems, beacon scan compensation is highly encouraged." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 150 and max_value <= 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Very High beacon offset: %.6fμm._N_You will encounter first layer problems on large prints unless you activate beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Extremely high beacon offset: %.6fμm._N_You have significant scan/contact inconsistency which is indicative of mechanical problems, please investigate before resorting to software compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon offset relative to the center" TYPE={type} MSG={'"_N_%s_N__N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s"' % (recommendation, line_1, line_2, line_3, line_4, line_5, line_6, line_7, line_8)}

[gcode_macro BEACON_CREATE_SCAN_COMPENSATION_MESH]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set profile = params.PROFILE|default("auto")|string %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set keep_temp_meshes = params.KEEP_TEMP_MESHES|default(0) %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' %}
	{% set desired_spacing = printer["gcode_macro RatOS"].beacon_scan_compensation_desired_spacing|float %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	
	{% if not beacon_scan_compensation_enable %}
	RATOS_ECHO MSG="Beacon scan compensation is disabled!"
	
	{% else %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	
	
	RATOS_ECHO MSG="Please wait..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	G1 Z2.5 F{z_speed}
	{% if beacon_adaptive_heat_soak %}
	
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,9000]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if not (beacon_adaptive_heat_soak or bed_heat_soak_time > 0) %}
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if printer.z_tilt is defined %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% endif %}
	{% if printer.quad_gantry_level is defined %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% endif %}
	
	
	_BEACON_CREATE_SCAN_COMPENSATION_MESH_CORE PROFILE="{profile}" DESIRED_SPACING={desired_spacing} CHAMBER_TEMP={chamber_temp} KEEP_TEMP_MESHES={keep_temp_meshes}
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	{% if automated %}
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon scan compensation mesh created!"
	
	
	{% if not automated %}
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED]
gcode = 
	
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED" MSG="beacon_scan_compensation_profile {beacon_scan_compensation_profile}, beacon_scan_compensation_enable {beacon_scan_compensation_enable}"
	
	{% if beacon_scan_compensation_enable %}
	BEACON_APPLY_SCAN_COMPENSATION PROFILE="{beacon_scan_compensation_profile}"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL]
gcode = 
	
	{% set beacon_contact_start_print_true_zero = params.BEACON_CONTACT_START_PRINT_TRUE_ZERO|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = params.beacon_contact_calibrate_model_on_true_zero|lower == 'true' %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and not printer.beacon.model %}
	{% set beacon_model_required_for_true_zero = beacon_contact_start_print_true_zero and not beacon_contact_calibrate_model_on_true_zero %}
	{% set beacon_model_required_for_homing =
	printer.fastconfig.settings.stepper_z.endstop_pin == 'probe:z_virtual_endstop'
	and (( printer.fastconfig.settings.beacon.home_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower != 'true')
	or ( printer.fastconfig.settings.beacon.default_probe_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower != 'true' )) %}
	{% if beacon_model_required_for_homing or beacon_model_required_for_true_zero %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("An active Beacon model is required. Have you performed initial Beacon calibration?") }
	{% endif %}
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION]
gcode = 
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set bed_temp_mismatch_is_error = true if printer["gcode_macro RatOS"].beacon_scan_compensation_bed_temp_mismatch_is_error|default(false)|lower == 'true' else false %}
	
	{% set bed_temp = params.BED_TEMP|default(0)|float %}
	{% if bed_temp == 0 %}
	{% set bed_temp = printer.heater_bed.temperature %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_PREFLIGHT_CHECK_BEACON" MSG="beacon_scan_compensation_profile={beacon_scan_compensation_profile}, beacon_scan_compensation_enable={beacon_scan_compensation_enable}, bed_temp={bed_temp}"
	
	{% if beacon_scan_compensation_enable %}
	_VALIDATE_COMPENSATION_MESH_PROFILE PROFILE="{beacon_scan_compensation_profile}" TITLE="Check Beacon scan compensation profile" SUBJECT="Configured compensation profile '{beacon_scan_compensation_profile}'" COMPARE_BED_TEMP={bed_temp} COMPARE_BED_TEMP_IS_ERROR={bed_temp_mismatch_is_error}
	{% endif %}

[gcode_macro _BEACON_MAYBE_SCAN_COMPENSATION]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set needs_scan_compensation = true if printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].needs_compensation|default(false)|lower == 'true' else false %}
	
	{% if needs_scan_compensation %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% endif %}

[gcode_macro _BEACON_HOME_AND_ABL]
gcode = 
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	{% if needs_rehoming %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}

[gcode_macro SAVE_Z_OFFSET]
description = Deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead, or in Mainsail use the SAVE button in the Z-OFFSET section.
gcode = 
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default('false')|lower == 'true' %}
	{% set msg = "SAVE_Z_OFFSET is deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead,_N_or in Mainsail use the SAVE button in the Z-OFFSET section."%}
	{% if not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% set msg = msg + "_N_You must then use the SAVE_CONFIG command to persist the change." %}
	{% endif %}
	CONSOLE_ECHO TYPE="error" MSG="{msg}"

[gcode_macro _BEACON_OFFSET_COMPARE]
gcode = 
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing..."
	
	
	BEACON_OFFSET_COMPARE SAMPLES_DROP=1 SAMPLES=3
	BEACON_QUERY

[fan]
pin = rpi:gpio4

[fan_generic part_fan_t0]
pin = PA8
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[fan_generic part_fan_t1]
pin = PE5
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[heater_fan toolhead_cooling_fan_t0]
heater = extruder
shutdown_speed = 1
pin = toolboard_t0:PB4

[heater_fan toolhead_cooling_fan_t1]
heater = extruder1
shutdown_speed = 1
pin = toolboard_t1:PB4

[controller_fan controller_fan]
pin = dinghy:PA4
tachometer_pin = dinghy:PC15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[z_offset_probe]
pin = ^PG10
z_offset = -7
y_offset = 0
x_offset = 37.5
speed = 10
samples = 3
sample_retract_dist = 5
lift_speed = 10.0
samples_result = median
samples_tolerance = 0.2
samples_tolerance_retries = 5

[neopixel vaoc_led]
pin = PB10
chain_count = 6
color_order = GRB

[heater_fan vaoc_fan]
pin = PD13
heater = heater_bed
fan_speed = 1.0
heater_temp = 50

[fan_generic filter]
pin = !PD14
enable_pin = PD15

[gcode_macro T0]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = True
variable_color = "7bff33"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = -32.6
variable_parking_position = -57.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=0 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[gcode_macro T1]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = False
variable_color = "0ea5e9"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = 532.6
variable_parking_position = 557.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=1 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[save_variables]
filename = /home/pi/printer_data/config/ratos-variables.cfg

[mcu dinghy]
serial = /dev/serial/by-id/usb-Klipper_stm32f072xb_Dragon_dinghy-if00

[temperature_sensor th0]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA0

[temperature_sensor th1]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA1

[temperature_sensor th2]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA2

[temperature_sensor th3]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA3

[controller_fan CTL2]
pin = dinghy:PB14
tachometer_pin = dinghy:PB15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[mcu plasma]
serial = /dev/serial/by-id/usb-Klipper_rp2040_Plasma-if00

[neopixel Chamber_Lights]
pin = plasma:gpio15
chain_count = 140
color_order = GRBW
initial_red = 0.0
initial_green = 0.0
initial_blue = 0.0
initial_white = 0.1

[beacon model default]
model_coef = 1.5287863993594841,
	1.9289099639750602,
	0.8838828622507556,
	0.25554883784260735,
	-0.015171504024913506,
	0.3044946127013882,
	0.15820427856566457,
	-0.25262403959326246,
	0.042488512846660914,
	0.16662470122520964
model_domain = 1.842634574664148e-07,1.9339206373083917e-07
model_range = 0.200000,5.000000
model_temp = 13.222247
model_offset = 0.00000

[bed_mesh default]
version = 1
points = 
	0.016163, 0.016713, 0.001923, -0.017658, -0.031574, -0.032498, -0.030898, -0.032177, -0.035213, -0.031148, -0.021322, -0.016924, -0.015012, -0.013911, -0.012197, -0.012583, -0.010489, -0.007529, -0.003986, -0.000980, 0.005518, 0.014442, 0.027426, 0.034677, 0.037410, 0.040391, 0.041842, 0.040369, 0.037615, 0.030776, 0.027664, 0.022856, 0.016892, 0.015398, 0.014717, 0.006921, 0.001532, 0.000731, 0.008657, 0.014036
	0.005356, -0.005066, -0.016998, -0.029668, -0.038334, -0.043672, -0.041139, -0.042488, -0.045199, -0.039432, -0.028746, -0.023642, -0.024058, -0.022802, -0.019679, -0.018514, -0.018102, -0.016476, -0.012722, -0.010077, -0.001809, 0.007180, 0.019853, 0.027754, 0.029964, 0.033626, 0.036783, 0.032018, 0.029372, 0.020847, 0.017634, 0.011926, 0.009013, 0.009254, 0.007972, -0.001380, -0.006940, -0.002160, 0.006135, 0.008330
	-0.004900, -0.006720, -0.021914, -0.039691, -0.050459, -0.050377, -0.046281, -0.048755, -0.054708, -0.051499, -0.033927, -0.027632, -0.030243, -0.031447, -0.024387, -0.021408, -0.020382, -0.018068, -0.015930, -0.013877, -0.006099, 0.003479, 0.013310, 0.024783, 0.025522, 0.030849, 0.033573, 0.031409, 0.025495, 0.016683, 0.011264, 0.008805, 0.006856, 0.008059, 0.007305, 0.002581, -0.003320, -0.003239, 0.004691, 0.010045
	-0.008791, -0.019334, -0.029149, -0.040533, -0.051698, -0.058235, -0.054863, -0.054840, -0.055692, -0.049534, -0.036731, -0.033053, -0.035667, -0.035315, -0.024352, -0.023825, -0.022538, -0.020438, -0.018207, -0.015389, -0.006515, 0.001966, 0.013591, 0.019434, 0.020600, 0.024967, 0.029425, 0.026812, 0.018980, 0.007878, 0.002360, 0.000859, 0.003849, 0.005649, 0.005421, -0.000416, -0.007906, -0.003164, 0.007582, 0.010039
	-0.018512, -0.018210, -0.033932, -0.050501, -0.061588, -0.064139, -0.060236, -0.062528, -0.067065, -0.062039, -0.045815, -0.039448, -0.040521, -0.042080, -0.033870, -0.030878, -0.027396, -0.024548, -0.021298, -0.020041, -0.011880, -0.002847, 0.008689, 0.015857, 0.015934, 0.018697, 0.022439, 0.022106, 0.017916, 0.005879, 0.001037, -0.001311, -0.001335, 0.001897, 0.003656, 0.000561, -0.006084, -0.005683, 0.000338, 0.006245
	-0.028558, -0.036721, -0.044680, -0.054969, -0.066140, -0.075045, -0.073515, -0.073161, -0.075696, -0.068963, -0.058892, -0.053111, -0.050990, -0.048040, -0.041262, -0.037419, -0.034866, -0.031845, -0.029787, -0.026524, -0.017896, -0.009322, -0.001010, 0.005819, 0.008058, 0.010456, 0.013266, 0.012529, 0.007992, -0.001491, -0.006769, -0.009303, -0.005980, -0.003567, -0.003340, -0.011496, -0.018818, -0.014808, -0.004181, -0.000733
	-0.037253, -0.038393, -0.053129, -0.066170, -0.075959, -0.079233, -0.077475, -0.082688, -0.086779, -0.083983, -0.069005, -0.062542, -0.060351, -0.058481, -0.051101, -0.043149, -0.039837, -0.037039, -0.034698, -0.031301, -0.024330, -0.019786, -0.010285, -0.001967, 0.002812, 0.004899, 0.009657, 0.006946, 0.002155, -0.005232, -0.009851, -0.011218, -0.011509, -0.010097, -0.010293, -0.013175, -0.018958, -0.019846, -0.012107, -0.005641
	-0.046584, -0.055590, -0.062606, -0.069218, -0.080399, -0.087414, -0.089037, -0.092376, -0.095115, -0.088957, -0.080802, -0.073290, -0.068741, -0.064591, -0.054452, -0.048270, -0.045916, -0.044559, -0.042047, -0.039605, -0.032667, -0.025789, -0.019495, -0.012773, -0.006697, -0.003025, 0.001413, 0.000817, -0.004738, -0.013008, -0.017605, -0.018191, -0.018524, -0.016356, -0.016750, -0.021992, -0.028943, -0.025791, -0.016146, -0.010447
	-0.051029, -0.051677, -0.068218, -0.079622, -0.088590, -0.089331, -0.089731, -0.096072, -0.105329, -0.100771, -0.087584, -0.079320, -0.075489, -0.072081, -0.064183, -0.054662, -0.048601, -0.049465, -0.047050, -0.045011, -0.040009, -0.032508, -0.025212, -0.018144, -0.011996, -0.008136, -0.003187, -0.003214, -0.006646, -0.013044, -0.019446, -0.020615, -0.022270, -0.021298, -0.020215, -0.020946, -0.026034, -0.026598, -0.021025, -0.012328
	-0.057184, -0.064908, -0.073093, -0.081584, -0.091971, -0.097048, -0.097688, -0.101869, -0.106651, -0.102162, -0.095658, -0.087938, -0.082718, -0.077017, -0.069608, -0.060682, -0.056889, -0.056864, -0.054260, -0.052011, -0.044563, -0.038927, -0.031943, -0.025832, -0.021170, -0.014319, -0.009046, -0.008543, -0.011751, -0.020287, -0.026608, -0.027259, -0.029120, -0.025549, -0.023221, -0.027725, -0.032477, -0.028427, -0.019343, -0.014932
	-0.060411, -0.062241, -0.080781, -0.090744, -0.100903, -0.099702, -0.098468, -0.104236, -0.116853, -0.112701, -0.102623, -0.095036, -0.091407, -0.089871, -0.079701, -0.070222, -0.064325, -0.063875, -0.062248, -0.059396, -0.052699, -0.047589, -0.041526, -0.028442, -0.024526, -0.019549, -0.015403, -0.014251, -0.017989, -0.022824, -0.027328, -0.029155, -0.033315, -0.032426, -0.027619, -0.030776, -0.033688, -0.032458, -0.027219, -0.019649
	-0.067541, -0.076514, -0.082321, -0.088656, -0.099968, -0.104930, -0.105875, -0.109051, -0.115531, -0.112996, -0.105760, -0.100390, -0.096171, -0.090011, -0.080050, -0.073632, -0.067451, -0.067031, -0.065225, -0.062471, -0.056370, -0.050129, -0.041626, -0.030801, -0.027579, -0.022472, -0.014826, -0.015306, -0.020316, -0.025953, -0.030661, -0.034103, -0.035502, -0.032738, -0.031311, -0.037314, -0.041306, -0.035280, -0.027449, -0.020395
	-0.068162, -0.069269, -0.088235, -0.096809, -0.103385, -0.103271, -0.102507, -0.109535, -0.123412, -0.118580, -0.106622, -0.099580, -0.097644, -0.096978, -0.087259, -0.077196, -0.068978, -0.067016, -0.063682, -0.062548, -0.057901, -0.052295, -0.044088, -0.032703, -0.026551, -0.021607, -0.014155, -0.013747, -0.017390, -0.022419, -0.027444, -0.030877, -0.033450, -0.032423, -0.032041, -0.033598, -0.035149, -0.034054, -0.029356, -0.020998
	-0.069473, -0.075924, -0.083569, -0.089648, -0.101235, -0.105828, -0.109144, -0.112613, -0.117233, -0.114186, -0.107090, -0.098616, -0.097084, -0.094257, -0.086773, -0.076409, -0.069532, -0.066472, -0.060956, -0.059191, -0.052886, -0.047752, -0.041275, -0.032437, -0.027780, -0.020398, -0.012061, -0.010133, -0.014056, -0.021528, -0.027924, -0.030605, -0.030609, -0.026068, -0.029346, -0.033991, -0.038254, -0.030610, -0.021109, -0.015885
	-0.068084, -0.066409, -0.083944, -0.094013, -0.102504, -0.105274, -0.106036, -0.112090, -0.121664, -0.117824, -0.104850, -0.097467, -0.098833, -0.098622, -0.089603, -0.078147, -0.068143, -0.066300, -0.061573, -0.057727, -0.054825, -0.048625, -0.040164, -0.030532, -0.025948, -0.020264, -0.014196, -0.010702, -0.013794, -0.019775, -0.026095, -0.028838, -0.030254, -0.027944, -0.027980, -0.030915, -0.032446, -0.028861, -0.023732, -0.014676
	-0.065280, -0.068669, -0.076948, -0.082397, -0.094986, -0.105117, -0.107099, -0.108954, -0.112557, -0.110326, -0.100725, -0.096325, -0.096240, -0.092388, -0.081185, -0.071682, -0.065650, -0.062250, -0.057027, -0.054691, -0.048349, -0.042069, -0.032712, -0.027728, -0.023396, -0.018458, -0.008357, -0.005699, -0.011447, -0.020033, -0.026387, -0.030280, -0.028443, -0.023735, -0.023838, -0.031580, -0.034204, -0.027768, -0.018029, -0.010628
	-0.061662, -0.057052, -0.075163, -0.086710, -0.094182, -0.097544, -0.098814, -0.105908, -0.114460, -0.111718, -0.097559, -0.091614, -0.093860, -0.093098, -0.081687, -0.069410, -0.064117, -0.062745, -0.055603, -0.051413, -0.048043, -0.040363, -0.031842, -0.023420, -0.017470, -0.012600, -0.008163, -0.003898, -0.007635, -0.013254, -0.019807, -0.025153, -0.027074, -0.023513, -0.023727, -0.028669, -0.029153, -0.024831, -0.018735, -0.009246
	-0.056176, -0.059439, -0.066501, -0.071527, -0.085216, -0.094918, -0.097595, -0.099419, -0.101847, -0.102015, -0.093849, -0.089867, -0.088840, -0.083167, -0.071832, -0.062522, -0.058023, -0.057771, -0.053050, -0.048285, -0.041374, -0.033527, -0.024473, -0.018428, -0.013958, -0.008161, -0.001196, 0.001754, -0.004016, -0.011132, -0.018325, -0.021813, -0.021514, -0.016948, -0.018061, -0.025702, -0.028671, -0.021470, -0.011028, -0.001934
	-0.059202, -0.050525, -0.065461, -0.076792, -0.084156, -0.088538, -0.090719, -0.096070, -0.105729, -0.105136, -0.090350, -0.083865, -0.087807, -0.086145, -0.074773, -0.064235, -0.057641, -0.055896, -0.051286, -0.046566, -0.042431, -0.034723, -0.023762, -0.014983, -0.009126, -0.004877, 0.000094, 0.003492, -0.000931, -0.005883, -0.011665, -0.015251, -0.016432, -0.016119, -0.015373, -0.018827, -0.019994, -0.017564, -0.012298, 0.002094
	-0.055561, -0.058184, -0.062669, -0.068111, -0.080741, -0.091895, -0.093911, -0.094387, -0.100239, -0.100695, -0.089841, -0.085682, -0.085212, -0.082910, -0.073072, -0.063594, -0.056157, -0.053482, -0.048107, -0.045405, -0.039982, -0.029777, -0.019905, -0.013872, -0.009732, -0.004272, 0.003500, 0.006909, 0.001302, -0.004626, -0.012374, -0.014751, -0.014637, -0.011794, -0.012913, -0.018244, -0.023377, -0.018086, -0.006575, 0.003294
	-0.062834, -0.047300, -0.060870, -0.073023, -0.079303, -0.082121, -0.083623, -0.091321, -0.100996, -0.098896, -0.085406, -0.078881, -0.081932, -0.082077, -0.074409, -0.063158, -0.053822, -0.050328, -0.045077, -0.039678, -0.035825, -0.028532, -0.017793, -0.009121, -0.003444, -0.000905, 0.003990, 0.007745, 0.004595, 0.000143, -0.004555, -0.007411, -0.010850, -0.010100, -0.010079, -0.013177, -0.016434, -0.014663, -0.010248, -0.000213
	-0.054748, -0.053907, -0.057576, -0.063118, -0.072478, -0.081366, -0.084424, -0.086348, -0.089718, -0.089305, -0.081771, -0.076889, -0.076923, -0.073518, -0.067973, -0.057643, -0.050848, -0.046966, -0.041560, -0.036436, -0.029233, -0.020685, -0.010240, -0.004935, -0.001084, 0.002478, 0.009168, 0.014038, 0.010885, 0.004752, -0.001650, -0.004209, -0.003998, -0.002336, -0.003784, -0.010930, -0.016480, -0.012798, -0.003650, 0.002998
	-0.059345, -0.041989, -0.057435, -0.068229, -0.072857, -0.072586, -0.075155, -0.083286, -0.091292, -0.089727, -0.073702, -0.068353, -0.072910, -0.073863, -0.065527, -0.053635, -0.046064, -0.043899, -0.037607, -0.031251, -0.026194, -0.018885, -0.008095, 0.000309, 0.004911, 0.007046, 0.010642, 0.015635, 0.015277, 0.012612, 0.008074, 0.004852, 0.001546, 0.000504, 0.000589, -0.002769, -0.006432, -0.007765, -0.005391, 0.006950
	-0.050324, -0.049088, -0.052417, -0.057257, -0.063818, -0.071057, -0.074636, -0.075459, -0.079445, -0.077368, -0.068788, -0.063940, -0.065040, -0.063419, -0.054864, -0.044910, -0.038774, -0.036951, -0.031149, -0.026080, -0.018383, -0.011985, -0.001732, 0.003893, 0.007180, 0.011120, 0.017429, 0.021738, 0.019167, 0.015812, 0.011027, 0.007243, 0.006720, 0.009346, 0.006598, -0.003776, -0.009199, -0.007592, 0.005481, 0.014396
	-0.058437, -0.035937, -0.050762, -0.060425, -0.061123, -0.059090, -0.062399, -0.072124, -0.080338, -0.074950, -0.060985, -0.054754, -0.059333, -0.060500, -0.051714, -0.038834, -0.031117, -0.031693, -0.025186, -0.017982, -0.014316, -0.010137, 0.000228, 0.008774, 0.014018, 0.016470, 0.019918, 0.022071, 0.021109, 0.019957, 0.018698, 0.015803, 0.013135, 0.011136, 0.008719, 0.003522, -0.000994, 0.000525, 0.006297, 0.018454
	-0.046143, -0.041577, -0.045391, -0.046668, -0.051722, -0.057607, -0.062802, -0.065205, -0.068243, -0.066293, -0.058216, -0.051324, -0.051806, -0.051018, -0.043393, -0.032431, -0.024016, -0.023321, -0.018504, -0.013897, -0.008455, -0.001123, 0.006609, 0.010462, 0.013887, 0.019328, 0.024804, 0.026590, 0.023420, 0.020337, 0.017129, 0.017199, 0.016391, 0.015616, 0.013257, 0.005832, -0.000019, 0.003462, 0.014308, 0.023624
	-0.051989, -0.030294, -0.043380, -0.051339, -0.050711, -0.048193, -0.052258, -0.061218, -0.070507, -0.068810, -0.049476, -0.042352, -0.046018, -0.046673, -0.038670, -0.027263, -0.018137, -0.018587, -0.013603, -0.008482, -0.004647, -0.000011, 0.008230, 0.015652, 0.019436, 0.023069, 0.024762, 0.027750, 0.028115, 0.026227, 0.022220, 0.023166, 0.020341, 0.018455, 0.014918, 0.011932, 0.007138, 0.008523, 0.014718, 0.026201
	-0.041448, -0.035286, -0.036538, -0.037577, -0.044652, -0.049300, -0.051092, -0.052841, -0.058068, -0.056947, -0.046235, -0.038436, -0.037494, -0.034175, -0.028932, -0.016904, -0.010075, -0.010552, -0.004464, -0.001243, 0.003236, 0.010200, 0.015604, 0.020362, 0.023157, 0.028023, 0.032826, 0.035958, 0.034819, 0.030600, 0.025988, 0.026013, 0.026284, 0.025661, 0.022322, 0.013336, 0.006464, 0.011312, 0.022330, 0.031668
	-0.048540, -0.022534, -0.035260, -0.042156, -0.042749, -0.037408, -0.038818, -0.047322, -0.056808, -0.053643, -0.035691, -0.027822, -0.028789, -0.028255, -0.020274, -0.007285, -0.000723, -0.000788, 0.005440, 0.008938, 0.008953, 0.012074, 0.017957, 0.025241, 0.029175, 0.032057, 0.033733, 0.038359, 0.039349, 0.037161, 0.034052, 0.034585, 0.032020, 0.029940, 0.026326, 0.024577, 0.020432, 0.021586, 0.024568, 0.034552
	-0.033086, -0.027982, -0.029443, -0.029011, -0.035629, -0.040579, -0.038290, -0.037389, -0.041260, -0.040430, -0.032279, -0.021394, -0.018817, -0.015525, -0.007558, 0.006345, 0.011048, 0.011271, 0.013497, 0.017030, 0.017449, 0.022752, 0.026764, 0.030722, 0.033532, 0.037203, 0.043356, 0.048536, 0.047776, 0.043851, 0.039311, 0.039944, 0.039954, 0.038931, 0.034893, 0.030946, 0.023127, 0.027359, 0.034859, 0.043920
	-0.036218, -0.016846, -0.030897, -0.036980, -0.037261, -0.033334, -0.030888, -0.034074, -0.042142, -0.039980, -0.021377, -0.013603, -0.014171, -0.013131, -0.001768, 0.014998, 0.020060, 0.018173, 0.019934, 0.024704, 0.023739, 0.024617, 0.027288, 0.035116, 0.041187, 0.043128, 0.045921, 0.051709, 0.053031, 0.050698, 0.047697, 0.047728, 0.046845, 0.043201, 0.041805, 0.040728, 0.036184, 0.034435, 0.035120, 0.045329
	-0.029808, -0.023871, -0.026541, -0.026705, -0.031203, -0.036908, -0.034411, -0.029231, -0.028090, -0.026102, -0.016691, -0.007747, -0.004471, 0.001560, 0.010738, 0.025062, 0.027672, 0.024833, 0.026976, 0.029502, 0.030754, 0.035709, 0.039403, 0.044719, 0.046379, 0.049250, 0.054178, 0.059793, 0.059542, 0.052111, 0.047608, 0.050103, 0.053142, 0.052747, 0.050045, 0.044102, 0.033149, 0.035392, 0.045678, 0.054080
	-0.032238, -0.008993, -0.023999, -0.030969, -0.028658, -0.024887, -0.024493, -0.028088, -0.031053, -0.022849, -0.003868, 0.004647, 0.004540, 0.007560, 0.018373, 0.031401, 0.035778, 0.033768, 0.035173, 0.035884, 0.036597, 0.038940, 0.044566, 0.053914, 0.056554, 0.056382, 0.056449, 0.060387, 0.062696, 0.058223, 0.055016, 0.056193, 0.056891, 0.052793, 0.052741, 0.052626, 0.048117, 0.045032, 0.048033, 0.055100
	-0.019758, -0.015110, -0.017814, -0.018871, -0.023340, -0.028653, -0.026880, -0.018681, -0.017020, -0.011343, -0.001002, 0.008249, 0.014012, 0.020367, 0.026878, 0.038534, 0.041827, 0.039532, 0.039775, 0.039109, 0.043172, 0.049325, 0.056604, 0.059583, 0.059329, 0.059876, 0.062766, 0.068759, 0.067214, 0.059657, 0.055950, 0.056798, 0.058619, 0.058591, 0.059849, 0.056473, 0.046841, 0.047921, 0.058342, 0.065346
	-0.018628, -0.000296, -0.014764, -0.022634, -0.020483, -0.016362, -0.015485, -0.017352, -0.020246, -0.010362, 0.008635, 0.018414, 0.018542, 0.024258, 0.033370, 0.045728, 0.049983, 0.044610, 0.044638, 0.047649, 0.049220, 0.051954, 0.058932, 0.065915, 0.069102, 0.067410, 0.067680, 0.073734, 0.072203, 0.067293, 0.063945, 0.064378, 0.065047, 0.061989, 0.062882, 0.063468, 0.059707, 0.057986, 0.059739, 0.066139
	-0.010091, -0.006551, -0.008018, -0.009589, -0.016068, -0.020662, -0.019451, -0.010985, -0.009391, -0.003580, 0.007826, 0.019598, 0.024961, 0.033762, 0.040618, 0.050868, 0.052139, 0.050495, 0.049198, 0.051777, 0.056840, 0.061771, 0.068414, 0.072295, 0.073443, 0.072145, 0.073414, 0.079338, 0.075988, 0.067367, 0.064745, 0.064435, 0.066982, 0.065811, 0.067424, 0.063230, 0.058438, 0.059982, 0.067672, 0.072460
	-0.016254, 0.006291, -0.008031, -0.013944, -0.014475, -0.010741, -0.009932, -0.011709, -0.015503, -0.006971, 0.013190, 0.024865, 0.029121, 0.033942, 0.044335, 0.054572, 0.058078, 0.055224, 0.055897, 0.058327, 0.061207, 0.063939, 0.070506, 0.078141, 0.084203, 0.081223, 0.079519, 0.082883, 0.080890, 0.076174, 0.071279, 0.073064, 0.071225, 0.066859, 0.069860, 0.070836, 0.069427, 0.069140, 0.070950, 0.075269
	-0.008127, 0.000730, 0.001164, -0.000308, -0.006659, -0.012343, -0.011463, -0.003755, -0.001876, 0.005166, 0.016616, 0.030243, 0.036509, 0.045020, 0.053681, 0.063738, 0.066425, 0.063964, 0.062796, 0.065633, 0.071912, 0.077280, 0.082580, 0.086477, 0.089798, 0.089603, 0.091453, 0.096125, 0.088708, 0.079903, 0.074317, 0.076190, 0.075399, 0.075242, 0.079628, 0.077855, 0.071473, 0.073702, 0.082757, 0.088086
	-0.010951, 0.013218, -0.000878, -0.006241, -0.005623, 0.000046, 0.000158, -0.002943, -0.005314, 0.005491, 0.026890, 0.035754, 0.041490, 0.045829, 0.059325, 0.070249, 0.074114, 0.071815, 0.073229, 0.076313, 0.080778, 0.081554, 0.087919, 0.096206, 0.101562, 0.101674, 0.100494, 0.103989, 0.100292, 0.093977, 0.088080, 0.088136, 0.086555, 0.081494, 0.084966, 0.087073, 0.084113, 0.085184, 0.087700, 0.092188
	-0.002972, 0.006020, 0.006098, 0.004303, 0.001326, -0.002386, -0.001840, 0.005325, 0.008624, 0.016246, 0.026781, 0.039696, 0.048540, 0.055938, 0.066982, 0.076497, 0.080828, 0.079669, 0.080127, 0.083754, 0.089783, 0.093456, 0.100570, 0.105322, 0.107132, 0.110571, 0.113141, 0.118064, 0.111721, 0.101634, 0.093555, 0.093112, 0.093104, 0.092325, 0.094780, 0.092552, 0.085283, 0.088882, 0.097508, 0.105280
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 11.4
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Preperations]
version = 1
points = 
	0.012158, -0.006098, -0.020628, -0.034069, -0.049418, -0.058491, -0.062706, -0.063181, -0.065552, -0.063461, -0.057373, -0.056717, -0.056579, -0.054080, -0.053373, -0.056878, -0.057281, -0.055224, -0.049676, -0.047605, -0.041454, -0.034605, -0.022490, -0.011292, -0.009411, -0.005344, -0.003510, -0.002717, -0.005999, -0.010712, -0.013141, -0.015611, -0.020004, -0.017667, -0.016629, -0.022248, -0.024864, -0.024065, -0.014921, -0.010826
	-0.005958, -0.021084, -0.033800, -0.047903, -0.059950, -0.071345, -0.072502, -0.073350, -0.075852, -0.072963, -0.067236, -0.064315, -0.065698, -0.064338, -0.062871, -0.065238, -0.067095, -0.063584, -0.059241, -0.057846, -0.051380, -0.043157, -0.030230, -0.019950, -0.018121, -0.014291, -0.009354, -0.013065, -0.016464, -0.022925, -0.025337, -0.026541, -0.030577, -0.029068, -0.027094, -0.030532, -0.034241, -0.032625, -0.021498, -0.020513
	-0.017526, -0.027763, -0.040710, -0.055305, -0.068172, -0.079641, -0.081247, -0.081903, -0.083679, -0.081855, -0.073270, -0.070340, -0.072083, -0.071536, -0.066055, -0.065901, -0.069085, -0.066531, -0.063284, -0.061616, -0.053366, -0.047292, -0.035451, -0.023167, -0.022205, -0.016699, -0.012552, -0.014153, -0.018802, -0.030443, -0.032210, -0.034051, -0.034437, -0.031439, -0.030406, -0.032817, -0.036351, -0.034849, -0.024250, -0.019489
	-0.017750, -0.030284, -0.043463, -0.055839, -0.071865, -0.084888, -0.086157, -0.084619, -0.086681, -0.084515, -0.075246, -0.073263, -0.075604, -0.075123, -0.069177, -0.070723, -0.071097, -0.068644, -0.065465, -0.063718, -0.057574, -0.049335, -0.036556, -0.028418, -0.028259, -0.023387, -0.018454, -0.020519, -0.027499, -0.038314, -0.041534, -0.041886, -0.039972, -0.036438, -0.033959, -0.033009, -0.038291, -0.036339, -0.022688, -0.024783
	-0.021354, -0.034103, -0.047541, -0.060551, -0.075691, -0.089373, -0.092241, -0.091621, -0.093203, -0.090723, -0.082480, -0.079781, -0.079706, -0.079674, -0.074365, -0.073780, -0.073465, -0.070165, -0.064970, -0.065503, -0.059104, -0.051038, -0.041817, -0.031243, -0.031386, -0.028837, -0.023658, -0.024237, -0.029641, -0.039210, -0.042766, -0.044461, -0.041863, -0.039075, -0.034881, -0.034571, -0.039386, -0.038253, -0.031659, -0.024202
	-0.027696, -0.041184, -0.054054, -0.064759, -0.080898, -0.094964, -0.097906, -0.098033, -0.101256, -0.098300, -0.091517, -0.088420, -0.086945, -0.085220, -0.079938, -0.079979, -0.079828, -0.074842, -0.072903, -0.072415, -0.065384, -0.057454, -0.048482, -0.040977, -0.039336, -0.036065, -0.032553, -0.034336, -0.039337, -0.046271, -0.049398, -0.051220, -0.049530, -0.045000, -0.045029, -0.042100, -0.049767, -0.046386, -0.035574, -0.032188
	-0.033426, -0.046259, -0.059363, -0.068024, -0.084858, -0.097009, -0.103434, -0.106215, -0.107319, -0.106178, -0.100333, -0.097536, -0.095352, -0.091322, -0.086332, -0.082309, -0.081440, -0.078413, -0.075067, -0.073134, -0.068255, -0.062667, -0.054300, -0.046004, -0.042001, -0.039181, -0.035010, -0.036092, -0.041599, -0.048788, -0.051751, -0.051179, -0.051019, -0.049121, -0.045860, -0.046756, -0.050005, -0.051613, -0.040237, -0.035349
	-0.037931, -0.051993, -0.066455, -0.075044, -0.088177, -0.102890, -0.108223, -0.112373, -0.115787, -0.113421, -0.108543, -0.105936, -0.101048, -0.096863, -0.090726, -0.087882, -0.086665, -0.083874, -0.081096, -0.080894, -0.075125, -0.071038, -0.063072, -0.054696, -0.051039, -0.046728, -0.042566, -0.043887, -0.048745, -0.056834, -0.059808, -0.060521, -0.060664, -0.057968, -0.056317, -0.052477, -0.058814, -0.055877, -0.046325, -0.042545
	-0.041429, -0.053634, -0.067633, -0.077111, -0.090998, -0.103561, -0.109445, -0.114741, -0.120075, -0.119821, -0.114703, -0.110411, -0.105589, -0.099826, -0.093730, -0.089705, -0.087199, -0.086439, -0.082688, -0.082221, -0.078348, -0.073203, -0.065273, -0.058731, -0.054025, -0.049231, -0.044830, -0.043830, -0.045839, -0.054137, -0.059075, -0.059515, -0.058546, -0.056956, -0.054145, -0.053129, -0.056587, -0.056341, -0.047057, -0.039936
	-0.044295, -0.058972, -0.072101, -0.082726, -0.095001, -0.106449, -0.111505, -0.118363, -0.124608, -0.123506, -0.120263, -0.115400, -0.110227, -0.104535, -0.100348, -0.095757, -0.092961, -0.092377, -0.089613, -0.088047, -0.084834, -0.079314, -0.072500, -0.064519, -0.060449, -0.055767, -0.051803, -0.050997, -0.052855, -0.058115, -0.063348, -0.065363, -0.067936, -0.063474, -0.061475, -0.054726, -0.062529, -0.055352, -0.048878, -0.044991
	-0.045804, -0.056574, -0.073308, -0.082450, -0.097495, -0.107467, -0.111501, -0.116418, -0.126724, -0.125980, -0.123231, -0.120494, -0.114667, -0.111289, -0.103451, -0.099228, -0.095880, -0.095882, -0.093328, -0.091000, -0.087051, -0.081909, -0.075949, -0.064971, -0.061050, -0.055137, -0.049046, -0.047319, -0.049806, -0.056968, -0.059608, -0.060249, -0.063032, -0.060556, -0.056284, -0.056263, -0.058891, -0.057890, -0.051554, -0.042382
	-0.049818, -0.062681, -0.076305, -0.084328, -0.098717, -0.107866, -0.113937, -0.120088, -0.128622, -0.128931, -0.126353, -0.123191, -0.118529, -0.115642, -0.106288, -0.103976, -0.099708, -0.097750, -0.094501, -0.094545, -0.090910, -0.085952, -0.077352, -0.067196, -0.062435, -0.057738, -0.052934, -0.051098, -0.055294, -0.061112, -0.063120, -0.067525, -0.067979, -0.066558, -0.064608, -0.060597, -0.067812, -0.057641, -0.056224, -0.046471
	-0.050591, -0.060432, -0.075602, -0.083877, -0.096933, -0.106147, -0.112334, -0.118295, -0.127966, -0.128757, -0.125157, -0.121831, -0.118557, -0.116124, -0.108723, -0.104502, -0.099469, -0.095841, -0.090662, -0.089822, -0.087969, -0.084545, -0.076375, -0.064821, -0.059093, -0.053427, -0.047372, -0.044341, -0.047964, -0.054064, -0.057133, -0.059152, -0.061568, -0.059109, -0.056640, -0.056691, -0.056844, -0.054564, -0.048514, -0.040641
	-0.047704, -0.059564, -0.073127, -0.080945, -0.093764, -0.105483, -0.111501, -0.118792, -0.124812, -0.126576, -0.122064, -0.118087, -0.116126, -0.114867, -0.108053, -0.103336, -0.097558, -0.093250, -0.086537, -0.085303, -0.083677, -0.079292, -0.070542, -0.062526, -0.056818, -0.052534, -0.044035, -0.041353, -0.046942, -0.051329, -0.055481, -0.062777, -0.058499, -0.058025, -0.057390, -0.053562, -0.060843, -0.046555, -0.046260, -0.036083
	-0.046496, -0.052983, -0.067518, -0.076904, -0.091704, -0.103105, -0.111995, -0.117751, -0.122307, -0.122941, -0.118230, -0.115004, -0.114258, -0.113138, -0.105515, -0.098417, -0.093384, -0.090070, -0.083281, -0.079846, -0.078725, -0.075452, -0.066225, -0.057269, -0.053103, -0.047808, -0.039772, -0.036834, -0.041270, -0.047376, -0.051111, -0.053848, -0.053029, -0.050301, -0.048919, -0.050775, -0.050121, -0.046842, -0.039633, -0.030497
	-0.040695, -0.051685, -0.064038, -0.070974, -0.086679, -0.101773, -0.109889, -0.114373, -0.117883, -0.118764, -0.113125, -0.110931, -0.111099, -0.109664, -0.098733, -0.093182, -0.090154, -0.086213, -0.077214, -0.077108, -0.075555, -0.069117, -0.060704, -0.054093, -0.049253, -0.044799, -0.037536, -0.035304, -0.040134, -0.045456, -0.051720, -0.056675, -0.053743, -0.052923, -0.049701, -0.050238, -0.056776, -0.041485, -0.041755, -0.027329
	-0.039842, -0.039428, -0.055732, -0.063890, -0.079179, -0.092823, -0.101698, -0.106156, -0.111709, -0.113152, -0.108033, -0.104872, -0.105645, -0.103501, -0.094487, -0.087264, -0.084273, -0.080950, -0.074116, -0.070973, -0.068409, -0.062825, -0.054757, -0.044150, -0.040620, -0.036602, -0.031538, -0.026478, -0.031123, -0.037600, -0.042341, -0.046700, -0.047380, -0.042880, -0.040967, -0.045367, -0.044192, -0.038553, -0.029948, -0.020790
	-0.030596, -0.038279, -0.051528, -0.058981, -0.073983, -0.089044, -0.099173, -0.101740, -0.104830, -0.107083, -0.102306, -0.101554, -0.101336, -0.097146, -0.089217, -0.083800, -0.080621, -0.078071, -0.071535, -0.068328, -0.065806, -0.056882, -0.048683, -0.039756, -0.036349, -0.031328, -0.025351, -0.024133, -0.029773, -0.033858, -0.040011, -0.044146, -0.043900, -0.044797, -0.038019, -0.042319, -0.047297, -0.031851, -0.034318, -0.013527
	-0.032121, -0.034722, -0.047839, -0.054710, -0.069175, -0.084213, -0.094533, -0.097233, -0.100863, -0.104775, -0.099781, -0.097416, -0.098804, -0.096059, -0.086694, -0.079692, -0.076749, -0.074609, -0.068106, -0.063906, -0.061136, -0.055447, -0.045559, -0.035389, -0.029696, -0.025708, -0.020034, -0.017335, -0.022665, -0.028532, -0.032369, -0.035760, -0.037212, -0.035201, -0.032872, -0.034132, -0.035907, -0.032127, -0.025026, -0.009282
	-0.026707, -0.034374, -0.045183, -0.052691, -0.067014, -0.084964, -0.092286, -0.094441, -0.099291, -0.103609, -0.098278, -0.094972, -0.097169, -0.095394, -0.086653, -0.080205, -0.076284, -0.070594, -0.064535, -0.062012, -0.060174, -0.051216, -0.040622, -0.033396, -0.029636, -0.024235, -0.017274, -0.018232, -0.021459, -0.024778, -0.031754, -0.034481, -0.033398, -0.037949, -0.030432, -0.033219, -0.038432, -0.021975, -0.030052, -0.009295
	-0.028559, -0.029280, -0.042071, -0.048655, -0.061603, -0.076257, -0.086817, -0.091815, -0.095682, -0.098682, -0.093729, -0.091168, -0.092213, -0.090073, -0.084070, -0.077048, -0.072045, -0.066267, -0.060309, -0.053639, -0.051696, -0.046852, -0.034069, -0.025602, -0.020640, -0.018021, -0.013180, -0.009049, -0.013846, -0.018012, -0.021061, -0.024515, -0.027068, -0.026804, -0.024283, -0.025595, -0.028234, -0.025272, -0.019246, -0.008595
	-0.025711, -0.029003, -0.038836, -0.048015, -0.058511, -0.074480, -0.083738, -0.087945, -0.091439, -0.094310, -0.090288, -0.087858, -0.088589, -0.086163, -0.081829, -0.075146, -0.071136, -0.064399, -0.057338, -0.052103, -0.049650, -0.043210, -0.032998, -0.023124, -0.020191, -0.016625, -0.012433, -0.010465, -0.009871, -0.015007, -0.021217, -0.021582, -0.023800, -0.027652, -0.021527, -0.027137, -0.030828, -0.020152, -0.026202, -0.008568
	-0.031287, -0.022523, -0.035800, -0.041583, -0.052691, -0.065901, -0.075941, -0.079246, -0.083936, -0.086778, -0.082235, -0.078893, -0.080642, -0.079419, -0.074324, -0.067418, -0.062113, -0.057744, -0.049923, -0.043390, -0.040055, -0.035512, -0.023838, -0.015485, -0.009895, -0.008346, -0.005387, 0.001467, -0.000104, -0.003777, -0.007926, -0.012023, -0.013970, -0.014207, -0.013994, -0.017009, -0.019233, -0.019282, -0.014210, -0.001146
	-0.020719, -0.024043, -0.035160, -0.041635, -0.051902, -0.063884, -0.072884, -0.076738, -0.081856, -0.083761, -0.077857, -0.074651, -0.077952, -0.076310, -0.069721, -0.063240, -0.056775, -0.055188, -0.046711, -0.042996, -0.039499, -0.032268, -0.023129, -0.015735, -0.012305, -0.009383, -0.005789, -0.001996, -0.001166, -0.005106, -0.009634, -0.009864, -0.011905, -0.015913, -0.010246, -0.016645, -0.022975, -0.011972, -0.018524, 0.001048
	-0.026050, -0.019774, -0.032555, -0.037813, -0.044657, -0.054435, -0.065271, -0.071019, -0.075585, -0.077479, -0.072635, -0.069526, -0.071046, -0.070770, -0.063085, -0.055960, -0.050956, -0.049593, -0.042773, -0.034996, -0.032645, -0.029030, -0.020343, -0.011008, -0.005751, -0.003252, 0.000746, 0.003215, 0.001749, -0.000068, -0.001413, -0.002608, -0.005837, -0.007103, -0.008431, -0.012027, -0.015656, -0.014417, -0.006321, 0.003748
	-0.021728, -0.019178, -0.031232, -0.036249, -0.042206, -0.053190, -0.064017, -0.068545, -0.074597, -0.074544, -0.069543, -0.065779, -0.067928, -0.067354, -0.060655, -0.052790, -0.047723, -0.046044, -0.038188, -0.034539, -0.032080, -0.027152, -0.018902, -0.012508, -0.009304, -0.003955, -0.000288, -0.001549, -0.000556, -0.003756, -0.008467, -0.003851, -0.005999, -0.012959, -0.007423, -0.015332, -0.017388, -0.005695, -0.010807, 0.007710
	-0.028204, -0.017096, -0.027984, -0.032129, -0.038374, -0.046561, -0.059356, -0.061847, -0.069228, -0.070551, -0.065474, -0.059719, -0.059893, -0.060271, -0.053666, -0.047202, -0.041189, -0.039979, -0.033189, -0.028761, -0.025714, -0.021660, -0.014905, -0.007841, -0.004669, -0.001174, 0.001874, 0.005613, 0.005527, 0.001504, -0.000694, 0.001892, 0.001885, -0.002506, -0.005619, -0.007166, -0.009935, -0.007406, 0.000545, 0.009983
	-0.019393, -0.017785, -0.025482, -0.028146, -0.036861, -0.047528, -0.055696, -0.059118, -0.064151, -0.066346, -0.060565, -0.055661, -0.055495, -0.051944, -0.048147, -0.040645, -0.036359, -0.035990, -0.026764, -0.024843, -0.023572, -0.019648, -0.013807, -0.006811, -0.004589, -0.000266, 0.003010, 0.004931, 0.006834, 0.003254, -0.001690, 0.003120, 0.001036, -0.005283, 0.000659, -0.007399, -0.010996, -0.000832, -0.006381, 0.012135
	-0.021519, -0.010062, -0.018662, -0.023011, -0.029067, -0.036961, -0.043194, -0.048197, -0.053632, -0.055489, -0.050054, -0.045247, -0.042655, -0.040243, -0.034315, -0.027094, -0.022697, -0.021644, -0.015333, -0.010768, -0.013712, -0.012051, -0.005326, 0.000560, 0.005300, 0.007429, 0.009930, 0.015968, 0.016454, 0.012383, 0.010385, 0.011612, 0.011413, 0.008357, 0.006831, 0.005524, 0.003087, 0.003507, 0.009876, 0.018892
	-0.017331, -0.015238, -0.021971, -0.024651, -0.029507, -0.040209, -0.044232, -0.046101, -0.052689, -0.053151, -0.047133, -0.042985, -0.040475, -0.037020, -0.029999, -0.021348, -0.018232, -0.017876, -0.013058, -0.008535, -0.013279, -0.011527, -0.006296, -0.001615, 0.002270, 0.006991, 0.010272, 0.013407, 0.015950, 0.012503, 0.008026, 0.013701, 0.011513, 0.004867, 0.010667, 0.006774, 0.003571, 0.012416, 0.004875, 0.020961
	-0.022637, -0.011107, -0.018340, -0.023896, -0.028320, -0.038092, -0.041212, -0.041642, -0.044537, -0.046015, -0.041699, -0.035805, -0.033527, -0.030911, -0.022925, -0.010175, -0.007279, -0.008644, -0.005065, -0.000597, -0.003797, -0.004052, 0.000635, 0.006175, 0.010857, 0.012993, 0.016956, 0.022765, 0.023298, 0.020262, 0.018285, 0.019467, 0.021161, 0.018785, 0.017891, 0.017817, 0.013874, 0.012825, 0.015904, 0.025844
	-0.014532, -0.010189, -0.019385, -0.022584, -0.028159, -0.037803, -0.040566, -0.038125, -0.040339, -0.038899, -0.033171, -0.028143, -0.025641, -0.019755, -0.012463, -0.003824, -0.000871, -0.002698, -0.000197, 0.001952, -0.001353, -0.000188, 0.004902, 0.012600, 0.014373, 0.016449, 0.018872, 0.022822, 0.026385, 0.020681, 0.015275, 0.021387, 0.023535, 0.016733, 0.022161, 0.018819, 0.011276, 0.020785, 0.014683, 0.032409
	-0.016972, -0.004835, -0.015539, -0.019706, -0.022971, -0.032222, -0.037732, -0.035551, -0.033892, -0.031679, -0.024624, -0.019946, -0.016412, -0.010040, -0.003445, 0.005991, 0.008364, 0.006410, 0.008289, 0.009260, 0.007409, 0.008691, 0.015230, 0.022729, 0.025465, 0.025502, 0.026102, 0.030309, 0.031861, 0.026963, 0.024651, 0.027000, 0.029039, 0.025577, 0.027217, 0.027660, 0.023245, 0.021705, 0.026383, 0.034120
	-0.007042, -0.003943, -0.013314, -0.016082, -0.020497, -0.030911, -0.035096, -0.030889, -0.029351, -0.025337, -0.018980, -0.012449, -0.008879, -0.001902, 0.003577, 0.011256, 0.012460, 0.010502, 0.011904, 0.011483, 0.010067, 0.013356, 0.020792, 0.027368, 0.026382, 0.028554, 0.028164, 0.029993, 0.033232, 0.028830, 0.022354, 0.027991, 0.029607, 0.020011, 0.031066, 0.031755, 0.025061, 0.037228, 0.024607, 0.041453
	-0.012463, -0.000987, -0.008994, -0.014815, -0.017487, -0.026372, -0.031392, -0.028459, -0.025402, -0.024153, -0.015566, -0.007862, -0.004579, 0.001484, 0.010757, 0.017401, 0.019536, 0.016264, 0.016278, 0.018231, 0.018193, 0.018217, 0.025442, 0.034794, 0.036179, 0.034770, 0.033985, 0.040104, 0.040404, 0.034161, 0.030977, 0.032380, 0.034144, 0.031909, 0.033231, 0.035957, 0.034171, 0.033050, 0.038776, 0.042972
	-0.002758, 0.000700, -0.008467, -0.011525, -0.018705, -0.027522, -0.031609, -0.027494, -0.026315, -0.023221, -0.014164, -0.006562, -0.002205, 0.006453, 0.013689, 0.018647, 0.017673, 0.016751, 0.017380, 0.018782, 0.019038, 0.021992, 0.027475, 0.034748, 0.036870, 0.036635, 0.035394, 0.037519, 0.038008, 0.032063, 0.025834, 0.030409, 0.033142, 0.023991, 0.034882, 0.034323, 0.030317, 0.042711, 0.030793, 0.045129
	-0.011501, 0.004979, -0.003199, -0.009532, -0.013737, -0.022490, -0.028056, -0.025047, -0.023987, -0.021727, -0.011113, -0.003633, 0.003070, 0.010580, 0.020230, 0.025058, 0.026653, 0.024592, 0.024567, 0.025613, 0.027386, 0.029282, 0.037705, 0.042901, 0.046601, 0.045443, 0.044217, 0.048155, 0.045715, 0.039788, 0.034981, 0.038594, 0.038594, 0.034532, 0.038671, 0.042065, 0.040659, 0.042101, 0.045919, 0.050030
	-0.005239, 0.006624, -0.001837, -0.005350, -0.012024, -0.022230, -0.026144, -0.022704, -0.021559, -0.017450, -0.008515, 0.000433, 0.007392, 0.014546, 0.023538, 0.029043, 0.029892, 0.027280, 0.028785, 0.030662, 0.032758, 0.032649, 0.040035, 0.046372, 0.048654, 0.050330, 0.049538, 0.049746, 0.048851, 0.041068, 0.034598, 0.041375, 0.041379, 0.030621, 0.043091, 0.044712, 0.038634, 0.053475, 0.042814, 0.059369
	-0.011843, 0.005417, 0.000007, -0.005709, -0.011391, -0.019100, -0.024151, -0.021274, -0.019356, -0.016953, -0.004422, 0.002891, 0.010688, 0.018353, 0.027665, 0.035281, 0.036655, 0.034937, 0.036795, 0.039994, 0.042705, 0.042668, 0.048600, 0.055673, 0.059602, 0.061002, 0.059934, 0.064283, 0.061835, 0.052838, 0.048644, 0.048401, 0.048158, 0.044262, 0.049173, 0.053313, 0.050054, 0.051718, 0.058112, 0.062677
	-0.003249, 0.007140, -0.000190, -0.005182, -0.010664, -0.017472, -0.021072, -0.018928, -0.015929, -0.011810, -0.001170, 0.006999, 0.014346, 0.022026, 0.033087, 0.037703, 0.039304, 0.038986, 0.040531, 0.042739, 0.044912, 0.045850, 0.052980, 0.060894, 0.062495, 0.065477, 0.066306, 0.069035, 0.066301, 0.058359, 0.048879, 0.054660, 0.053906, 0.042834, 0.051292, 0.054304, 0.049390, 0.064968, 0.053062, 0.067337
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 80.0
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Peperations]
version = 1
points = 
	0.022498, 0.020830, 0.014175, -0.000111, -0.007965, -0.011932, -0.009252, -0.003320, -0.000118, 0.004151, 0.015991, 0.024593, 0.030148, 0.034696, 0.042241, 0.043592, 0.045307, 0.051419, 0.057700, 0.066468, 0.072764, 0.085492, 0.100446, 0.113063, 0.118900, 0.122870, 0.130290, 0.129755, 0.129462, 0.124089, 0.122420, 0.123461, 0.116841, 0.117893, 0.119241, 0.115227, 0.110631, 0.109920, 0.117187, 0.124332
	0.004953, 0.000716, -0.005511, -0.010742, -0.018400, -0.024021, -0.019665, -0.013525, -0.009878, -0.004126, 0.008939, 0.016408, 0.019292, 0.023840, 0.033007, 0.033600, 0.034448, 0.041047, 0.049029, 0.052882, 0.062512, 0.072410, 0.089182, 0.103027, 0.106205, 0.110789, 0.117912, 0.115269, 0.112784, 0.106051, 0.103603, 0.104209, 0.099603, 0.105100, 0.101466, 0.099610, 0.095780, 0.096420, 0.108661, 0.108286
	-0.007933, -0.002801, -0.011350, -0.022484, -0.029473, -0.033231, -0.030354, -0.021826, -0.018408, -0.013209, 0.001640, 0.008984, 0.012027, 0.014149, 0.024334, 0.028649, 0.030597, 0.034667, 0.041223, 0.046241, 0.051968, 0.062511, 0.079099, 0.090699, 0.097837, 0.101667, 0.108218, 0.106595, 0.104490, 0.095444, 0.089512, 0.089259, 0.089179, 0.091741, 0.094161, 0.094254, 0.091002, 0.088753, 0.095405, 0.102343
	-0.010759, -0.012564, -0.018170, -0.023960, -0.033106, -0.040910, -0.038354, -0.031441, -0.026122, -0.019953, -0.006267, 0.000733, 0.002678, 0.006102, 0.015437, 0.019860, 0.022689, 0.029563, 0.035629, 0.037302, 0.045089, 0.055137, 0.070820, 0.082978, 0.087158, 0.088614, 0.094487, 0.093851, 0.091038, 0.080923, 0.074433, 0.073797, 0.073058, 0.081788, 0.080734, 0.083111, 0.078149, 0.079373, 0.091335, 0.087853
	-0.027313, -0.019238, -0.027920, -0.036645, -0.043223, -0.049872, -0.048503, -0.043853, -0.040737, -0.035179, -0.021622, -0.013493, -0.010171, -0.007317, 0.001347, 0.007440, 0.011360, 0.015985, 0.023916, 0.026329, 0.031680, 0.042865, 0.056754, 0.067621, 0.072919, 0.075964, 0.080156, 0.081233, 0.077771, 0.068443, 0.063939, 0.062251, 0.063828, 0.065094, 0.069498, 0.071735, 0.067423, 0.064065, 0.069162, 0.076272
	-0.033298, -0.035618, -0.039940, -0.043358, -0.050731, -0.061413, -0.060545, -0.055944, -0.052261, -0.045471, -0.035624, -0.027633, -0.021472, -0.017300, -0.006949, -0.002776, -0.000154, 0.006413, 0.012882, 0.014721, 0.023411, 0.031711, 0.040565, 0.054702, 0.058761, 0.061734, 0.065369, 0.066037, 0.061059, 0.053849, 0.049600, 0.048373, 0.049189, 0.054631, 0.050470, 0.056349, 0.047074, 0.049651, 0.057444, 0.057485
	-0.046284, -0.039039, -0.049010, -0.054961, -0.061001, -0.068408, -0.069602, -0.066474, -0.063117, -0.059357, -0.049570, -0.041166, -0.035441, -0.029269, -0.019658, -0.012395, -0.008906, -0.005538, 0.002012, 0.008339, 0.013216, 0.018793, 0.031185, 0.040165, 0.047175, 0.050605, 0.054283, 0.054442, 0.049166, 0.043483, 0.039000, 0.040758, 0.040857, 0.040759, 0.042263, 0.043438, 0.040051, 0.035886, 0.041332, 0.048851
	-0.049893, -0.051919, -0.058103, -0.060142, -0.067656, -0.077159, -0.079195, -0.078019, -0.075421, -0.069471, -0.060409, -0.054194, -0.044226, -0.037275, -0.027912, -0.020020, -0.016789, -0.012491, -0.003457, 0.001129, 0.004540, 0.009435, 0.018232, 0.027941, 0.035138, 0.038227, 0.042656, 0.044103, 0.038517, 0.032121, 0.029666, 0.027319, 0.029774, 0.031572, 0.028887, 0.034828, 0.023795, 0.030023, 0.033606, 0.036047
	-0.061015, -0.055279, -0.067497, -0.072234, -0.078637, -0.083600, -0.085954, -0.087271, -0.088647, -0.083447, -0.073398, -0.065920, -0.058009, -0.048810, -0.040714, -0.032533, -0.027328, -0.020402, -0.011382, -0.006547, -0.005452, -0.002712, 0.004649, 0.014201, 0.021442, 0.025510, 0.032890, 0.034711, 0.030965, 0.026329, 0.018828, 0.019246, 0.018861, 0.019611, 0.020596, 0.021396, 0.020172, 0.015723, 0.020537, 0.029677
	-0.063777, -0.066149, -0.073750, -0.076131, -0.084016, -0.091900, -0.093741, -0.094496, -0.094840, -0.089548, -0.084332, -0.077263, -0.068485, -0.061963, -0.051082, -0.043658, -0.037912, -0.032323, -0.024324, -0.019914, -0.018261, -0.013727, -0.003485, 0.004316, 0.011418, 0.017023, 0.022980, 0.024505, 0.018896, 0.014000, 0.009498, 0.006074, 0.009480, 0.007611, 0.008958, 0.010086, -0.000341, 0.010423, 0.010467, 0.016794
	-0.072341, -0.064233, -0.079217, -0.084483, -0.091050, -0.094481, -0.095378, -0.096667, -0.100564, -0.098313, -0.093254, -0.086700, -0.079209, -0.071795, -0.061313, -0.051911, -0.046317, -0.042643, -0.037228, -0.031598, -0.027431, -0.020480, -0.012883, -0.003114, 0.004746, 0.010189, 0.015911, 0.017106, 0.014037, 0.008693, 0.005120, 0.003652, -0.000532, -0.001097, 0.001984, 0.000397, -0.002089, -0.002821, 0.000529, 0.009043
	-0.068927, -0.075835, -0.083530, -0.085213, -0.091299, -0.100015, -0.101020, -0.100921, -0.103349, -0.102493, -0.098069, -0.091292, -0.083452, -0.079672, -0.069612, -0.062472, -0.055862, -0.052233, -0.046746, -0.041991, -0.035219, -0.028225, -0.018698, -0.007309, -0.002458, 0.002051, 0.006595, 0.008468, 0.005218, -0.000205, -0.003131, -0.003647, -0.006151, -0.009154, -0.005539, -0.006971, -0.015297, -0.002874, -0.005242, 0.003706
	-0.070116, -0.067835, -0.086390, -0.089881, -0.095167, -0.099194, -0.100751, -0.103794, -0.106996, -0.105835, -0.098564, -0.092154, -0.085579, -0.083053, -0.074722, -0.066442, -0.059302, -0.053429, -0.047800, -0.042952, -0.039132, -0.034614, -0.025732, -0.012689, -0.005906, 0.001101, 0.006644, 0.010980, 0.007742, 0.002526, -0.000261, -0.004094, -0.008771, -0.008465, -0.007095, -0.008952, -0.010405, -0.010446, -0.006121, 0.002024
	-0.064366, -0.071780, -0.082938, -0.085702, -0.093522, -0.099237, -0.104020, -0.105939, -0.106226, -0.104298, -0.097541, -0.091253, -0.084969, -0.082450, -0.075561, -0.066547, -0.056511, -0.051248, -0.041287, -0.037794, -0.035633, -0.028059, -0.019518, -0.010556, -0.003388, 0.002054, 0.009492, 0.011478, 0.008555, 0.004735, -0.000781, -0.006427, -0.005697, -0.010270, -0.006112, -0.011704, -0.018717, -0.002750, -0.010971, 0.000116
	-0.076795, -0.064801, -0.080209, -0.085175, -0.093457, -0.101077, -0.104981, -0.106367, -0.106821, -0.105708, -0.098545, -0.090759, -0.086929, -0.083491, -0.074306, -0.064805, -0.055933, -0.049959, -0.042853, -0.036270, -0.034463, -0.029587, -0.018780, -0.010103, -0.003533, 0.001632, 0.007909, 0.014370, 0.009281, 0.004666, -0.002974, -0.007301, -0.010185, -0.008299, -0.006340, -0.009678, -0.011333, -0.010684, -0.006289, 0.002763
	-0.067470, -0.065770, -0.074038, -0.076420, -0.085702, -0.098704, -0.101940, -0.102629, -0.101903, -0.100342, -0.093820, -0.086941, -0.083804, -0.081020, -0.067700, -0.059395, -0.054055, -0.047911, -0.039687, -0.035672, -0.032029, -0.025979, -0.017057, -0.006973, -0.001656, 0.002001, 0.007249, 0.012112, 0.006541, 0.000572, -0.006284, -0.010415, -0.012279, -0.015087, -0.007848, -0.016491, -0.019704, -0.005357, -0.013151, 0.002966
	-0.074820, -0.054794, -0.069710, -0.075127, -0.082743, -0.091434, -0.095621, -0.097541, -0.099098, -0.097422, -0.089851, -0.083594, -0.081112, -0.078942, -0.066391, -0.057457, -0.050942, -0.048077, -0.041211, -0.034391, -0.030091, -0.026047, -0.014207, -0.005090, 0.000912, 0.005316, 0.010043, 0.015509, 0.011199, 0.004513, -0.001027, -0.006694, -0.011239, -0.011162, -0.009134, -0.013596, -0.014031, -0.011306, -0.007627, 0.001767
	-0.061695, -0.056074, -0.065188, -0.067950, -0.076218, -0.088303, -0.093436, -0.092999, -0.090937, -0.090555, -0.084407, -0.080354, -0.078692, -0.074308, -0.062767, -0.052729, -0.047475, -0.043949, -0.036669, -0.031720, -0.027940, -0.020058, -0.010125, -0.000940, 0.003512, 0.007720, 0.011869, 0.015296, 0.011180, 0.003886, -0.003309, -0.003380, -0.007926, -0.011633, -0.003540, -0.014182, -0.013975, -0.003720, -0.011797, 0.006338
	-0.070864, -0.046187, -0.061128, -0.065717, -0.072715, -0.083470, -0.088292, -0.087558, -0.087628, -0.089378, -0.083768, -0.077237, -0.077063, -0.071978, -0.061635, -0.052022, -0.046913, -0.041194, -0.034314, -0.028661, -0.027048, -0.021438, -0.009769, -0.001205, 0.004637, 0.008928, 0.013264, 0.017277, 0.013442, 0.007295, 0.003623, -0.002524, -0.004256, -0.005789, -0.004213, -0.007305, -0.010487, -0.010885, -0.006086, 0.007386
	-0.059345, -0.049207, -0.056858, -0.060052, -0.066579, -0.080604, -0.086910, -0.085647, -0.085267, -0.087618, -0.081260, -0.075368, -0.073937, -0.069758, -0.058235, -0.051634, -0.045288, -0.038732, -0.032262, -0.027928, -0.024928, -0.019266, -0.007996, 0.000923, 0.005834, 0.008336, 0.013557, 0.017068, 0.012350, 0.006475, 0.000982, 0.001103, -0.006223, -0.006853, -0.000966, -0.013148, -0.013975, -0.006310, -0.011605, 0.006165
	-0.066591, -0.039715, -0.053663, -0.059514, -0.065911, -0.075018, -0.080214, -0.082968, -0.083447, -0.085380, -0.079055, -0.071985, -0.070247, -0.065856, -0.057767, -0.049975, -0.044481, -0.039103, -0.031217, -0.024927, -0.020997, -0.016440, -0.004831, 0.004061, 0.009463, 0.011160, 0.014777, 0.020638, 0.017816, 0.011360, 0.006171, 0.002164, -0.002119, -0.003117, -0.003031, -0.005156, -0.011400, -0.011762, -0.009295, -0.000001
	-0.060314, -0.046160, -0.052794, -0.054967, -0.062049, -0.074106, -0.080446, -0.081200, -0.080809, -0.080477, -0.076170, -0.070932, -0.069101, -0.063634, -0.055720, -0.049501, -0.044939, -0.040131, -0.032438, -0.022882, -0.017627, -0.012524, -0.001324, 0.006685, 0.011868, 0.013658, 0.016095, 0.021837, 0.020158, 0.012528, 0.006089, 0.005453, -0.000976, -0.002140, 0.001104, -0.010111, -0.010612, -0.007452, -0.014357, 0.001011
	-0.075633, -0.036609, -0.049346, -0.055490, -0.059336, -0.067616, -0.073859, -0.075613, -0.076372, -0.078009, -0.070627, -0.064206, -0.064430, -0.061999, -0.054551, -0.047386, -0.040817, -0.037398, -0.028062, -0.018505, -0.012195, -0.007531, 0.001481, 0.011790, 0.019955, 0.022349, 0.022131, 0.024492, 0.023359, 0.019186, 0.014655, 0.008357, 0.004176, 0.002971, 0.002955, -0.000237, -0.005884, -0.010152, -0.009506, 0.002811
	-0.059008, -0.039658, -0.046978, -0.048324, -0.052285, -0.063338, -0.069082, -0.070556, -0.070625, -0.070049, -0.064460, -0.057403, -0.056723, -0.052882, -0.046968, -0.041507, -0.033211, -0.029974, -0.022900, -0.013579, -0.008803, -0.004962, 0.005653, 0.017026, 0.028171, 0.028651, 0.024731, 0.026850, 0.023371, 0.017073, 0.015171, 0.016616, 0.005521, 0.005756, 0.007586, -0.005103, -0.006856, -0.005604, -0.006599, 0.007528
	-0.068330, -0.030233, -0.043154, -0.047439, -0.047149, -0.051149, -0.060971, -0.063014, -0.065775, -0.064636, -0.058200, -0.050987, -0.050925, -0.050115, -0.041299, -0.033907, -0.026306, -0.024199, -0.017123, -0.009196, -0.006314, -0.003809, 0.004760, 0.015324, 0.026665, 0.029649, 0.028724, 0.027131, 0.025150, 0.021808, 0.019981, 0.016766, 0.012347, 0.008776, 0.005760, -0.000224, -0.004294, -0.005879, -0.002457, 0.010054
	-0.053519, -0.031388, -0.038255, -0.037590, -0.039245, -0.046335, -0.056314, -0.057830, -0.060291, -0.058967, -0.051413, -0.045449, -0.043947, -0.042018, -0.034113, -0.025887, -0.019539, -0.017727, -0.012711, -0.005860, -0.003102, 0.000774, 0.009438, 0.015884, 0.022961, 0.024229, 0.026012, 0.029407, 0.026717, 0.020406, 0.017796, 0.020289, 0.012243, 0.009711, 0.009234, -0.005990, -0.001013, 0.000740, -0.002144, 0.013012
	-0.068972, -0.023416, -0.032912, -0.036134, -0.035915, -0.040435, -0.047452, -0.051460, -0.055021, -0.055776, -0.048697, -0.039554, -0.036785, -0.035561, -0.029056, -0.021075, -0.013416, -0.012134, -0.007237, -0.000622, 0.001662, 0.005393, 0.012038, 0.019764, 0.023514, 0.026252, 0.028191, 0.031400, 0.031365, 0.027993, 0.023275, 0.021009, 0.018930, 0.014093, 0.009022, 0.004773, 0.002094, 0.001348, 0.005643, 0.015078
	-0.050527, -0.022437, -0.028090, -0.026206, -0.028387, -0.036911, -0.041310, -0.044227, -0.046970, -0.046769, -0.038081, -0.031386, -0.029516, -0.024050, -0.019435, -0.012381, -0.005732, -0.004173, 0.000911, 0.006849, 0.007360, 0.010699, 0.017436, 0.023369, 0.028527, 0.029640, 0.031002, 0.034727, 0.036582, 0.030763, 0.026015, 0.028623, 0.020834, 0.016185, 0.016933, 0.002829, 0.004984, 0.009818, 0.008874, 0.020032
	-0.067395, -0.010220, -0.021024, -0.024567, -0.024087, -0.029620, -0.032317, -0.034341, -0.038392, -0.038789, -0.030285, -0.021590, -0.017175, -0.014435, -0.007732, -0.000529, 0.005605, 0.007078, 0.012454, 0.017758, 0.016774, 0.015574, 0.020748, 0.028369, 0.033644, 0.034771, 0.036537, 0.040293, 0.042118, 0.039979, 0.035655, 0.033354, 0.030928, 0.024890, 0.021491, 0.018938, 0.013668, 0.012501, 0.017108, 0.023515
	-0.038833, -0.012802, -0.018564, -0.017459, -0.019062, -0.027068, -0.030119, -0.028336, -0.029665, -0.030695, -0.022239, -0.013522, -0.008358, -0.004785, 0.000463, 0.010662, 0.015564, 0.016950, 0.020281, 0.025300, 0.022680, 0.022717, 0.026679, 0.031617, 0.035801, 0.037098, 0.041294, 0.045640, 0.047879, 0.042000, 0.038044, 0.040629, 0.033892, 0.031247, 0.031584, 0.018500, 0.020116, 0.019823, 0.016638, 0.029979
	-0.054356, -0.002258, -0.012712, -0.017288, -0.016713, -0.022907, -0.024293, -0.021563, -0.022620, -0.021953, -0.015330, -0.005386, -0.000764, 0.002640, 0.009997, 0.022869, 0.028174, 0.027730, 0.030977, 0.035707, 0.032818, 0.030889, 0.033638, 0.038561, 0.044265, 0.045141, 0.047683, 0.051815, 0.054004, 0.050991, 0.045574, 0.043899, 0.044055, 0.039092, 0.035909, 0.032091, 0.026891, 0.022169, 0.024865, 0.030848
	-0.031827, -0.000102, -0.006368, -0.006487, -0.006247, -0.014001, -0.017110, -0.013043, -0.010851, -0.008764, -0.000213, 0.006477, 0.011144, 0.018309, 0.024745, 0.033643, 0.038648, 0.039249, 0.041148, 0.045266, 0.041693, 0.040999, 0.045484, 0.052613, 0.057066, 0.054753, 0.055112, 0.059287, 0.060203, 0.052465, 0.047993, 0.050999, 0.047464, 0.046460, 0.044507, 0.031433, 0.032267, 0.032025, 0.029852, 0.040329
	-0.053848, 0.008122, -0.005187, -0.009032, -0.006543, -0.010012, -0.013005, -0.011663, -0.008957, -0.004668, 0.005458, 0.012800, 0.016893, 0.023554, 0.031737, 0.038741, 0.043870, 0.043337, 0.046621, 0.047581, 0.045654, 0.044827, 0.050363, 0.058747, 0.061023, 0.060485, 0.059059, 0.061821, 0.061391, 0.055971, 0.051067, 0.050038, 0.051018, 0.046533, 0.043334, 0.042562, 0.036118, 0.029798, 0.032773, 0.039524
	-0.025830, 0.006164, -0.000655, 0.000164, 0.000088, -0.008033, -0.011008, -0.006017, -0.001301, 0.004088, 0.011848, 0.020276, 0.024465, 0.033383, 0.039126, 0.044268, 0.047916, 0.047402, 0.050050, 0.050456, 0.048891, 0.051771, 0.058154, 0.063246, 0.065463, 0.063072, 0.060950, 0.065351, 0.064614, 0.057455, 0.051194, 0.055723, 0.050906, 0.046407, 0.048283, 0.036561, 0.037400, 0.036887, 0.031589, 0.046759
	-0.041184, 0.017683, 0.006408, 0.000358, 0.001923, -0.002498, -0.003907, -0.001746, 0.001864, 0.006784, 0.017297, 0.026916, 0.030940, 0.036439, 0.045987, 0.050809, 0.054636, 0.052055, 0.053180, 0.056698, 0.057069, 0.055779, 0.063193, 0.067815, 0.071856, 0.070651, 0.067674, 0.070718, 0.070797, 0.062598, 0.057842, 0.056835, 0.056713, 0.051260, 0.048727, 0.048227, 0.044844, 0.039559, 0.041218, 0.044920
	-0.014008, 0.018619, 0.011274, 0.010878, 0.008771, 0.001246, -0.001819, 0.003600, 0.008052, 0.011983, 0.021970, 0.030757, 0.037662, 0.045972, 0.053195, 0.057661, 0.059206, 0.058383, 0.060240, 0.061039, 0.062504, 0.064497, 0.070278, 0.077704, 0.080246, 0.077015, 0.072985, 0.075685, 0.072584, 0.063534, 0.057732, 0.061938, 0.057545, 0.050931, 0.054863, 0.045820, 0.048882, 0.049675, 0.043484, 0.051538
	-0.045038, 0.028947, 0.019821, 0.012917, 0.013648, 0.007951, 0.005122, 0.007823, 0.012411, 0.015320, 0.025036, 0.036734, 0.045314, 0.052208, 0.062220, 0.065610, 0.068489, 0.066665, 0.068454, 0.069025, 0.071080, 0.073373, 0.079623, 0.085651, 0.088907, 0.088954, 0.084254, 0.084464, 0.080300, 0.072471, 0.067316, 0.066430, 0.065143, 0.057630, 0.058650, 0.059627, 0.057197, 0.054105, 0.055295, 0.057879
	-0.017117, 0.027364, 0.023067, 0.022758, 0.019246, 0.011825, 0.007962, 0.011522, 0.017237, 0.021779, 0.031329, 0.042642, 0.052349, 0.060322, 0.069568, 0.074657, 0.075211, 0.072882, 0.075373, 0.078391, 0.079512, 0.081816, 0.086101, 0.091730, 0.095061, 0.095682, 0.092100, 0.092873, 0.085769, 0.077219, 0.068392, 0.073179, 0.069972, 0.061240, 0.068306, 0.062227, 0.061008, 0.064520, 0.058543, 0.070728
	-0.042759, 0.035472, 0.029514, 0.023812, 0.024176, 0.020576, 0.017397, 0.018716, 0.022981, 0.027634, 0.041262, 0.050991, 0.058558, 0.067060, 0.077829, 0.083609, 0.084719, 0.082815, 0.085352, 0.087363, 0.091238, 0.091692, 0.096562, 0.102513, 0.106436, 0.108184, 0.105828, 0.107257, 0.102415, 0.090768, 0.084257, 0.081410, 0.081286, 0.073523, 0.074433, 0.076576, 0.070376, 0.068350, 0.071896, 0.072962
	-0.003143, 0.035517, 0.033266, 0.032727, 0.031843, 0.025862, 0.023177, 0.026936, 0.032953, 0.037457, 0.049289, 0.057429, 0.066625, 0.072540, 0.083814, 0.089321, 0.092420, 0.093053, 0.094752, 0.096876, 0.098364, 0.101271, 0.105185, 0.113505, 0.115784, 0.118957, 0.117138, 0.117934, 0.110930, 0.101497, 0.091051, 0.092731, 0.090574, 0.079282, 0.084691, 0.078426, 0.073451, 0.081698, 0.072811, 0.084352
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 19.8
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 130, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 123, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 112, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/neopixel.py", line 111, in load_config_prefix
    return PrinterNeoPixel(config)
  File "/home/pi/klipper/klippy/extras/neopixel.py", line 42, in __init__
    raise config.error("neopixel chain too long")
configparser.Error: neopixel chain too long
webhooks client 4133779224: New connection
webhooks client 4133779224: Client info {'program': 'Moonraker', 'version': 'v0.9.3-0-g71f9e67'}
Starting Klippy...
Args: ['/home/pi/klipper/klippy/klippy.py', '/home/pi/printer_data/config/printer.cfg', '-l', '/home/pi/printer_data/logs/klippy.log', '-I', '/home/pi/printer_data/comms/klippy.serial', '-a', '/home/pi/printer_data/comms/klippy.sock']
Git version: 'v0.12.0-402-g2817b348e-dirty'
Untracked files: klippy/extras/beacon.py, klippy/extras/beacon_adaptive_heat_soak.py, klippy/extras/beacon_mesh.py, klippy/extras/beacon_true_zero_correction.py, klippy/extras/beacon_user_z_offset.py, klippy/extras/fastconfig.py, klippy/extras/gcode_shell_command.py, klippy/extras/linear_movement_vibrations.py, klippy/extras/named_offsets.py, klippy/extras/ratos.py, (+4 files)
Branch: master
Remote: origin
Tracked URL: https://github.com/Klipper3d/klipper.git
CPU: 4 core ?
Python: '3.9.2 (default, Jan 24 2026, 09:41:14) \n[GCC 10.2.1 20210110]'
Start printer at Tue Mar 17 03:55:11 2026 (1773719711.7 9316.1)
===== Config file =====
[mcu rpi]
serial = /tmp/klipper_host_mcu

[board_pins btt-octopus-pro-h723-11]
aliases = 
	
	
	
	x_step_pin=PF13,
	x_dir_pin=PF12,
	x_enable_pin=PF14,
	x_uart_pin=PC4,
	x_diag_pin=PG6,
	x_endstop_pin=PG6,
	
	
	
	dual_carriage_step_pin=PF9,
	dual_carriage_dir_pin=PF10,
	dual_carriage_enable_pin=PG2,
	dual_carriage_uart_pin=PF2,
	dual_carriage_diag_pin=PG12,
	dual_carriage_endstop_pin=PG12,
	
	
	
	y_step_pin=PG0,
	y_dir_pin=PG1,
	y_enable_pin=PF15,
	y_uart_pin=PD11,
	y_diag_pin=PG9,
	y_endstop_pin=PG9,
	
	
	
	y1_step_pin=PG4,
	y1_dir_pin=PC1,
	y1_enable_pin=PA2,
	y1_uart_pin=PC7,
	y1_diag_pin=PG11,
	y1_endstop_pin=PG11,
	
	
	
	z0_step_pin=PC13,
	z0_dir_pin=PF0,
	z0_enable_pin=PF1,
	z0_uart_pin=PE4,
	z0_diag_pin=PG13,
	
	
	
	z1_step_pin=PE2,
	z1_dir_pin=PE3,
	z1_enable_pin=PD4,
	z1_uart_pin=PE1,
	z1_diag_pin=PG14,
	
	
	
	z2_step_pin=PE6,
	z2_dir_pin=PA14,
	z2_enable_pin=PE0,
	z2_uart_pin=PD3,
	z2_diag_pin=PG15,
	
	e_step_pin=PF11,
	e_dir_pin=PG3,
	e_enable_pin=PG5,
	e_uart_pin=PC6,
	
	e_heater_pin=PA2,
	e_sensor_pin=PF4,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=PA7,
	stepper_spi_miso_pin=PA6,
	stepper_spi_sclk_pin=PA5,
	adxl345_cs_pin=PA15,
	bltouch_sensor_pin=PB7,
	bltouch_control_pin=PB6,
	probe_pin=PB7,
	fan_part_cooling_pin=PA8,
	fan_toolhead_cooling_pin=PE5,
	fan_controller_board_pin=PD12,
	heater_bed_heating_pin=PA1,
	heater_bed_sensor_pin=PF3,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PG15,
	filament_sensor_motion_pin=PG14,
	ratrig_vaoc_probe_pin=PG10,
	ratrig_vaoc_led_pin=PB0,
	ratrig_vaoc_fan_pin=PD13,
	chamber_lighting_pin=PB11,
	chamber_filter_4p_fan_pin=PD14,
	chamber_filter_4p_fan_enable_pin=PD15

[mcu]
serial = /dev/RatOS/btt-octopus-pro-h723-11

[temperature_sensor Octopus_Pro_H723_V1.1]
sensor_type = temperature_mcu

[adxl345 controlboard]
cs_pin = PA15
spi_software_mosi_pin = PB5
spi_software_miso_pin = PB4
spi_software_sclk_pin = PB3

[board_pins toolboard_t0]
mcu = toolboard_t0
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t0]
serial = /dev/RatOS/btt-ebb42-gen2-10-t0

[temperature_sensor EBB42_Gen2_v1.0_T0]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t0

[lis2dw toolboard_t0]
axes_map = x, z, y
cs_pin = toolboard_t0:PB1
spi_software_mosi_pin = toolboard_t0:PB11
spi_software_miso_pin = toolboard_t0:PB2
spi_software_sclk_pin = toolboard_t0:PB10

[board_pins toolboard_t1]
mcu = toolboard_t1
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t1]
serial = /dev/RatOS/btt-ebb42-gen2-10-t1

[temperature_sensor EBB42_Gen2_v1.0_T1]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t1

[lis2dw toolboard_t1]
axes_map = x, z, y
cs_pin = toolboard_t1:PB1
spi_software_mosi_pin = toolboard_t1:PB11
spi_software_miso_pin = toolboard_t1:PB2
spi_software_sclk_pin = toolboard_t1:PB10

[gcode_macro RatOS]
variable_homing = "endstops"
variable_z_probe = "static"
variable_sensorless_x_current = 0.6
variable_sensorless_y_current = 0.9
variable_safe_home_x = "middle"
variable_safe_home_y = "middle"
variable_driver_type_x = "tmc2209"
variable_driver_type_y = "tmc2209"
variable_stowable_probe_stop_on_error = False
variable_chamber_filter_enable = True
variable_chamber_filter_speed = 0.5
variable_chamber_filter_disable_speed = 1.0
variable_chamber_filter_enable_at = "after_print_start"
variable_chamber_filter_disable_period = 300
variable_chamber_filter_disable_bed_temp = 0
variable_chamber_heater_enable = True
variable_chamber_heater_bed_temp = 115
variable_chamber_heater_preheating_temp = 150
variable_chamber_heater_heating_temp_offset = 25
variable_chamber_heater_control_external_heater = False
variable_chamber_heater_air_circulation_enable = True
variable_chamber_heater_air_circulation_fan_speed = 0.35
variable_chamber_heater_air_circulation_y_pos = 0
variable_chamber_heater_air_circulation_z_pos = 100
variable_chamber_heater_extra_fan_speed = 1.0
variable_chamber_heater_filter_fan_speed = 1.0
variable_bed_heat_soak_time = 0
variable_hotend_heat_soak_time = 0
variable_led_status_action = 0.0,1.0,1.0
variable_led_status_success = 0.0,1.0,0.0
variable_led_status_error = 1.0,0.0,1.0
variable_led_status_on = 1.0,1.0,1.0
variable_led_status_off = 0.0,0.0,1.0
variable_led_status_standby = 0.1,0.1,0.1
variable_led_status_heating = 1.0,0.0,0.0
variable_led_status_cooling = 0.0,0.0,1.0
variable_calibrate_bed_mesh = True
variable_adaptive_mesh = True
variable_start_print_park_in = "center"
variable_start_print_park_z_height = 3
variable_end_print_park_in = "back"
variable_pause_print_park_in = "back"
variable_end_print_park_z_hop = 20
variable_nozzle_priming = "primeblob"
variable_nozzle_prime_start_x = "max"
variable_nozzle_prime_start_y = "min"
variable_nozzle_prime_direction = "auto"
variable_nozzle_prime_bridge_fan = 102
variable_probe_for_priming_result = None
variable_probe_for_priming_end_result = None
variable_probe_for_priming_result_t1 = None
variable_probe_for_priming_end_result_t1 = None
variable_probe_for_priming_disable_mesh_constraints = False
variable_adaptive_prime_offset_threshold = -1.0
variable_last_z_offset = None
variable_runout_park_in = "front"
variable_enable_unload_tip_forming = False
variable_filament_unload_length = 150
description = RatOS variable storage macro, will echo variables to the console when run.
variable_relative_extrusion = True
variable_force_absolute_position = False
variable_preheat_extruder = True
variable_preheat_extruder_temp = 150
variable_macro_travel_speed = 600
variable_macro_travel_accel = 8000
variable_macro_z_speed = 15
variable_bed_margin_x = [59.6, 59.6]
variable_bed_margin_y = [14.35, 33.65]
variable_printable_x_min = 0
variable_printable_x_max = 0
variable_printable_y_min = 0
variable_printable_y_max = 0
variable_end_print_motors_off = True
variable_status_color_ok = "00FF00"
variable_status_color_error = "FF0000"
variable_status_color_unknown = "FFFF00"
variable_end_print_retract_filament = 10
gcode = 
	ECHO_RATOS_VARS
variable_auto_center_subject = False
variable_toolchange_zhop = 2.0
variable_toolchange_zspeed = 25
variable_toolchange_sync_fans = False
variable_toolchange_combined_zhop = False
variable_toolchange_travel_speed = 600
variable_toolchange_travel_accel = 8000
variable_toolchange_extrusion = 2.0
variable_toolchange_retraction = 2.0
variable_toolchange_feedrate = 7200
variable_toolchange_prepurging_timer = 0
variable_toolchange_standby_temp = -1
variable_toolchange_purge = 25
variable_toolchange_first_purge = 50
variable_beacon_bed_mesh_scv = 25
variable_beacon_contact_z_homing = False
variable_beacon_contact_start_print_true_zero = True
variable_beacon_contact_start_print_true_zero_fuzzy_position = True
variable_beacon_contact_calibrate_model_on_true_zero = True
variable_beacon_contact_wipe_before_true_zero = True
variable_beacon_contact_wipe_before_true_zero_method = "probe_clean"
variable_beacon_contact_true_zero_temp = 170
variable_beacon_contact_prime_probing = True
variable_beacon_contact_expansion_compensation = True
variable_beacon_contact_bed_mesh = False
variable_beacon_contact_bed_mesh_samples = 2
variable_beacon_contact_z_tilt_adjust = False
variable_beacon_contact_z_tilt_adjust_samples = 2
variable_beacon_scan_compensation_enable = True
variable_beacon_scan_compensation_profile = "auto"
variable_beacon_scan_compensation_desired_spacing = 10
variable_beacon_scan_compensation_bed_temp_mismatch_is_error = False
variable_beacon_contact_poke_bottom_limit = -1
variable_beacon_scan_method_automatic = False
variable_beacon_adaptive_heat_soak = True
variable_beacon_adaptive_heat_soak_max_wait = 5400
variable_beacon_adaptive_heat_soak_extra_wait_after_completion = 0
variable_beacon_adaptive_heat_soak_layer_quality = 3
variable_beacon_adaptive_heat_soak_maximum_first_layer_duration = 1800
variable_beacon_contact_start_print_true_zero_fuzzy_radius = 20
variable_homing_x = "endstop"
variable_homing_y = "endstop"
variable_default_toolhead = 0
variable_adxl_chip = ["lis2dw toolboard_t0", "lis2dw toolboard_t1"]
variable_shaper_x_freq = [54.2, 53.2, 53.6, 54.4]
variable_shaper_y_freq = [40.8, 47.6, 38.6, 38]
variable_shaper_x_type = ["mzv", "mzv", "mzv", "mzv"]
variable_shaper_y_type = ["mzv", "mzv", "mzv", "mzv"]
variable_x_driver_types = ["tmc5160"]
variable_x_axes = ["x"]
variable_y_driver_types = ["tmc5160", "tmc5160"]
variable_y_axes = ["y", "y1"]
variable_z_driver_types = ["tmc2209", "tmc2209", "tmc2209"]
variable_z_axes = ["z", "z1", "z2"]
variable_home_y_first = True

[ratos_homing]
axes = xyz
z_hop = 15
z_hop_speed = 15
gcode = 
	
	_LED_ON
	
	
	{% set prev_stop_on_error = printer["gcode_macro RatOS"].stowable_probe_stop_on_error %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set target_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	_IDEX_SINGLE
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE=True
	
	
	M400
	
	G90
	
	
	{% set X = true if params.X is defined else false %}
	{% set Y = true if params.Y is defined else false %}
	{% set Z = true if params.Z is defined else false %}
	{% if printer["gcode_macro RatOS"].home_y_first|default(false)|lower == 'true' %}
	HOME_Y X={X} Y={Y} Z={Z}
	HOME_X X={X} Y={Y} Z={Z}
	{% else %}
	HOME_X X={X} Y={Y} Z={Z}
	HOME_Y X={X} Y={Y} Z={Z}
	{% endif %}
	HOME_Z X={X} Y={Y} Z={Z}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE={prev_stop_on_error}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[gcode_macro HOME_X]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_x = printer["gcode_macro RatOS"].homing_x|lower %}
	{% set homing_x = homing_x if homing_x else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_X" MSG="printable_x_max: {printable_x_max}, safe_home_x: {safe_home_x}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}"
	
	
	{% if X or not Y and not Z %}
	{% if homing_x == 'endstop' %}
	G28 X
	{% elif homing_x == 'sensorless' %}
	{% if printer["dual_carriage"] is defined %}
	{ action_emergency_stop("sensorless homing not supported on IDEX!") }
	{% endif %}
	HOME_X_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_x to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_x, homing)) }
	{% endif %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1} MODE=PRIMARY
	G1 X{parking_position} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	{% endif %}
	{% set x_homed = True %}
	G0 X{safe_home_x} F{speed}
	M400
	{% endif %}

[gcode_macro HOME_Y]
gcode = 
	
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_y = printer["gcode_macro RatOS"].homing_y|lower %}
	{% set homing_y = homing_y if homing_y else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Y" MSG="printable_y_max: {printable_y_max}, safe_home_y: {safe_home_y}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}"
	
	
	{% if Y or not X and not Z %}
	{% if homing_y == 'endstop' %}
	G28 Y
	{% elif homing_y == 'sensorless' %}
	HOME_Y_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_y to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_y, homing)) }
	{% endif %}
	{% set y_homed = True %}
	G0 Y{safe_home_y} F{speed}
	{% endif %}

[gcode_macro HOME_Z]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	
	
	{% set beacon_contact_z_homing = true if printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_z_home_position_fuzzing_radius = printer["gcode_macro RatOS"].beacon_z_home_position_fuzzing_radius|default(0)|float %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Z" MSG="x_homed: {x_homed}, y_homed: {y_homed}, z_probe: {z_probe}, beacon_contact_z_homing: {beacon_contact_z_homing}"
	
	
	{% if Z or not Y and not X %}
	RATOS_ECHO MSG="Homing Z"
	{% if x_homed == False or y_homed == False %}
	{ action_emergency_stop("X and Y must be homed before homing Z") }
	{% else %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_homing %}
	{% if beacon_contact_start_print_true_zero %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% else %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	{% else %}
	G28 Z
	{% endif %}
	_Z_HOP
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro HOME_X_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	
	G4 P300
	
	G28 X
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"

[gcode_macro HOME_Y_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	
	G4 P300
	
	G28 Y
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"

[gcode_macro _Z_HOP]
description = Move Z axis up by Z_HOP distance at Z_HOP_SPEED. In relative mode it will move Z axis up by Z_HOP distance. In absolute mode it will move Z axis to Z_HOP distance.
gcode = 
	{% set z_hop = printer.fastconfig.config.ratos_homing.z_hop|float %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	G0 Z{z_hop} F{z_hop_speed}

[gcode_macro __MOVE_TO_SAFE_Z_HOME_ECHO_DEBUG]
gcode = 
	DEBUG_ECHO PREFIX="_MOVE_TO_SAFE_Z_HOME" MSG="x: {params.X}, y: {params.Y}, z_hop: {params.Z_HOP}, fuzzy_radius: {params.FUZZY_RADIUS}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}, printable_x_max: {printer['gcode_macro RatOS'].printable_x_max}, printable_y_max: {printer['gcode_macro RatOS'].printable_y_max}"

[gcode_macro MAYBE_HOME]
description = Only home unhomed axis. Specify ABL=1 to also ensure that automatic bed levelling is applied (if configured).
variable_is_kinematic_position_overriden = False
gcode = 
	{% set abl = params.ABL|default('')|lower in ('true', 'yes', '1') %}
	{% if printer["gcode_macro MAYBE_HOME"].is_kinematic_position_overriden|lower == 'true' %}
	RATOS_ECHO MSG="SET_CENTER_KINEMATIC_POSITION has been abused. Homing all axes. Please refrain from using SET_CENTER_KINEMATIC_POSITION outside of debugging purposes."
	G28
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=False
	{% else %}
	{% set axes = '' %}
	{% set isHomed = true %}
	{% set axesToHome = '' %}
	{% if params.X is defined %}
	{% set axes = axes ~ 'X ' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% endif %}
	{% if params.Y is defined %}
	{% set axes = axes ~ 'Y ' %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% endif %}
	{% if params.Z is defined %}
	{% set axes = axes ~ 'Z ' %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if params.X is not defined and params.Y is not defined and params.Z is not defined %}
	{% set axes = '' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if isHomed is false %}
	RATOS_ECHO MSG="Homing {axesToHome}"
	G28 {axesToHome}
	{% else %}
	RATOS_ECHO MSG="All requested axes already homed. Skipping homing."
	{% endif %}
	{% endif %}
	{% if abl %}
	{% if printer.z_tilt is defined %}
	{% if not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Performing Z tilt adjustment..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Z tilt already applied. Skipping Z tilt adjustment."
	{% endif %}
	{% elif printer.quad_gantry_level is defined %}
	{% if not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Performing quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Quad gantry leveling already applied. Skipping quad gantry leveling."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="No automatic bed leveling method configured. Skipping bed leveling."
	{% endif %}
	{% endif %}

[gcode_macro PID_CALIBRATE_HOTEND]
description = Perform a PID calibration test for a given extruder heater.
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set temp = params.TEMP|default(220)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_HOTEND" MSG="TEMP={temp}"
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO MSG="PID calibration hotend heater T0 at {temp}°C..."
	PID_CALIBRATE HEATER=extruder TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	
	{% if toolhead==0 or toolhead==1 %}
	RATOS_ECHO MSG="PID calibration hotend heater T{toolhead} at {temp}°C..."
	PID_CALIBRATE HEATER=extruder{'' if toolhead==0 else toolhead} TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_BED]
description = Perform a PID calibration test for the bed heater.
gcode = 
	
	{% set temp = params.TEMP|default(80)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_BED" MSG="TEMP={temp}"
	RATOS_ECHO MSG="PID calibration bed heater at {temp}°C..."
	
	
	PID_CALIBRATE HEATER=heater_bed TARGET={temp}
	
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_CHAMBER_HEATER]
description = Perform a PID calibration test for the chamber heater.
gcode = 
	
	{% set temp = params.TEMP|default(150)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_CHAMBER_HEATER" MSG="TEMP={temp}"
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	RATOS_ECHO MSG="PID calibration chamber heater at {temp}°C..."
	PID_CALIBRATE HEATER=chamber_heater TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_heater" %}
	{% set link_text = "RatOS Chamber Heater" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber heater found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro INITIALIZE_PA_TUNING]
description = Start a pressure advance tuning tower.
gcode = 
	
	{% set start = params.START|default(0.0)|float %}
	{% set factor = params.FACTOR|default(0.001)|float %}
	
	
	{% set layer_number = printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|default(0)|int %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if is_printing_gcode and layer_number < 2 %}
	DEBUG_ECHO PREFIX="START_PA_TOWER" MSG="START: {start}, FACTOR: {factor}"
	RATOS_ECHO MSG="Starting pressure advance tuning tower..."
	TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START={start} FACTOR={factor}
	{% else %}
	RATOS_ECHO MSG="Pressure advance tuning tower requires you to be printing gcode and on layer 1 to start."
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro CHAMBER_FILTER_ON]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	_CHAMBER_FILTER_TURN_ON
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro CHAMBER_FILTER_OFF]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Deactivating chamber filter..."
	_CHAMBER_FILTER_TURN_OFF
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set chamber_filter_enable_at = printer["gcode_macro RatOS"].chamber_filter_enable_at|default('after_print_start')|lower %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_ON" MSG="at: {at}, chamber_filter_enable: {chamber_filter_enable}, chamber_filter_enable_at: {chamber_filter_enable_at}, chamber_filter_speed: {chamber_filter_speed}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	{% if chamber_filter_enable_at == at %}
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	
	
	_CHAMBER_FILTER_TURN_ON AT={at}
	
	
	{% if chamber_filter_enable_at == "print_end" %}
	_LED_CHAMBER_FILTER_ON
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_OFF]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF" MSG="chamber_filter_enable: {chamber_filter_enable}, filter_disable_period: {filter_disable_period}, filter_disable_bed_temp: {filter_disable_bed_temp}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	
	{% if filter_disable_period > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting {filter_disable_period} seconds before turning chamber filter off..."
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION={filter_disable_period}
	{% endif %}
	
	
	{% if filter_disable_bed_temp > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting for bed temp to cool down to {filter_disable_bed_temp}°C to turn filter off..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM=0 MAXIMUM={filter_disable_bed_temp}
	_CHAMBER_FILTER_TURN_OFF
	_LED_CHAMBER_FILTER_OFF
	{% endif %}
	
	{% endif %}

[delayed_gcode _CHAMBER_FILTER_OFF_TIMER]
gcode = 
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF_TIMER" MSG="executed"
	
	
	_CHAMBER_FILTER_TURN_OFF
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Chamber filter turned off!"
	
	
	_LED_CHAMBER_FILTER_OFF

[gcode_macro _CHAMBER_FILTER_TURN_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_speed|default(0)|float %}
	{% if at == "print_end" %}
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_disable_speed|default(0)|float %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION=0
	
	
	SET_FAN_SPEED FAN=filter SPEED={chamber_filter_speed}

[gcode_macro _CHAMBER_FILTER_TURN_OFF]
gcode = 
	
	SET_FAN_SPEED FAN=filter SPEED=0

[gcode_macro _CHAMBER_FILTER_SANITY_CHECK]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	{% if filter_disable_bed_temp > 0 and filter_disable_period > 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable, not both.")}
	{% endif %}
	
	{% if filter_disable_bed_temp == 0 and filter_disable_period == 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable.")}
	{% endif %}
	
	{% endif %}

[gcode_macro CHAMBER_HEATER_ON]
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(45)|int %}
	
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp} IS_FROM_START_PRINT=False

[gcode_macro CHAMBER_HEATER_OFF]
gcode = 
	_CHAMBER_HEATER_OFF

[gcode_macro _CHAMBER_HEATER_ON]
variable_chamber_temp = 0
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	{% set is_from_start_print = true if params.IS_FROM_START_PRINT|default(True)|lower == 'true' else false %}
	
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set chamber_heater_enable = true if printer["gcode_macro RatOS"].chamber_heater_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}
	{% set chamber_heater_preheating_temp = printer["gcode_macro RatOS"].chamber_heater_preheating_temp|default(150)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	{% set chamber_heater_control_external_heater = true if printer["gcode_macro RatOS"].chamber_heater_control_external_heater|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_enable = true if printer["gcode_macro RatOS"].chamber_heater_air_circulation_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_fan_speed = printer["gcode_macro RatOS"].chamber_heater_air_circulation_fan_speed|default(0.35)|float %}
	{% set chamber_heater_air_circulation_y_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_y_pos|default(0)|float %}
	{% set chamber_heater_air_circulation_z_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_z_pos|default(100)|float %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_HEATER_ON" MSG="chamber_heater_enable: {chamber_heater_enable}, chamber_heater_preheating_temp: {chamber_heater_preheating_temp}, chamber_heater_heating_temp_offset: {chamber_heater_heating_temp_offset}, bed_temp: {bed_temp}, chamber_temp: {chamber_temp}, start_chamber_temp: {start_chamber_temp}"
	
	
	{% if chamber_heater_enable and chamber_temp > 0 and chamber_heater_bed_temp > 0 %}
	
	
	_LED_HEATING
	
	
	RATOS_ECHO MSG="Preheating chamber to {(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}°C..."
	
	
	{% set chamber_temp_sensor = "extruder" %}
	{% if printer["dual_carriage"] is defined and default_toolhead == 1 %}
	{% set chamber_temp_sensor = "extruder1" %}
	{% endif %}
	{% if printer["temperature_sensor chamber"] is defined %}
	{% set chamber_temp_sensor = "temperature_sensor chamber" %}
	{% endif %}
	
	
	{% set current_chamber_temp = printer['%s' % chamber_temp_sensor].temperature|int %}
	
	
	{% set needs_heating = current_chamber_temp < (start_chamber_temp if start_chamber_temp > 0 else chamber_temp) %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_BEFORE_PREHEATING
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	{% if not is_from_start_print %}
	MAYBE_HOME
	{% endif %}
	G0 Z{chamber_heater_air_circulation_z_pos} F{z_speed}
	G0 Y{chamber_heater_air_circulation_y_pos} F{speed}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * chamber_heater_air_circulation_fan_speed)}
	{% endif %}
	{% else %}
	{% if is_from_start_print %}
	G0 Z{z} F{z_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE={chamber_temp}
	
	
	{% if needs_heating %}
	
	
	M140 S{chamber_heater_bed_temp}
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={chamber_heater_preheating_temp}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	
	{% endif %}
	
	
	{% if needs_heating %}
	_CHAMBER_HEATER_EXTRA_FAN_ON
	{% endif %}
	
	
	{% if needs_heating %}
	TEMPERATURE_WAIT SENSOR="{chamber_temp_sensor}" MINIMUM={(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% endif %}
	
	
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED=0
	_CHAMBER_FILTER_ON AT="before_print_start"
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	G28 Z
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_AFTER_PREHEATING
	{% endif %}
	
	
	{% if printer["temperature_sensor chamber"] is defined %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined and chamber_heater_control_external_heater %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	
	
	_LED_SUCCESS
	
	{% endif %}

[gcode_macro _CHAMBER_HEATER_OFF]
gcode = 
	RATOS_ECHO MSG="Deactivating chamber heater..."
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=0
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE=0
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	
	
	_CHAMBER_HEATER_EXTRA_FAN_OFF

[delayed_gcode _CHAMBER_HEATER_CONTROL]
initial_duration = 0.
gcode = 
	
	{% set chamber_temp = printer["gcode_macro _CHAMBER_HEATER_ON"].chamber_temp|default(0)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	
	
	{% set current_chamber_temp = printer['temperature_sensor chamber'].temperature|int %}
	
	
	{% if current_chamber_temp < chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	{% endif %}
	
	
	{% if current_chamber_temp >= chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_ON]
gcode = 
	
	{% set chamber_heater_extra_fan_speed = printer["gcode_macro RatOS"].chamber_heater_extra_fan_speed|default(0.0)|float %}
	
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	{% if chamber_heater_extra_fan_speed > 0 %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED={chamber_heater_extra_fan_speed}
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_OFF]
gcode = 
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED=0
	{% endif %}

[gcode_macro _USER_CHAMBER_HEATER_BEFORE_PREHEATING]
description = Will be executed before chamber preheating, only if heating is needed.
gcode = 

[gcode_macro _USER_CHAMBER_HEATER_AFTER_PREHEATING]
description = Will be executed after chamber preheating, only if heating was needed.
gcode = 

[gcode_macro RESET_HEATSOAK_SETTINGS]
description = Resets all heatsoak-related settings to startup defaults
gcode = 
	HEATSOAK_SETTINGS ACTION=reset

[gcode_macro USE_ADAPTIVE_HEATSOAK]
description = Temporarily enables adaptive bed heatsoaking (if a beacon probe is present), will reset to printer.cfg settings
	when Klipper is restarted. Optionally specify QUALITY (1-5) and maximum FIRST_LAYER_DURATION (in minutes).
	Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.QUALITY|default("1..5") %}
	{% set _ = params.FIRST_LAYER_DURATION|default("1..120 minutes") %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("Adaptive heatsoaking is only available when a beacon probe is configured.") }
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_quality = (settings.variable_beacon_adaptive_heat_soak_layer_quality if defsrc == 'startup' else current.beacon_adaptive_heat_soak_layer_quality)|default(3)|int %}
	{% set default_first_layer_duration_secs = (settings.variable_beacon_adaptive_heat_soak_maximum_first_layer_duration if defsrc == 'startup' else current.beacon_adaptive_heat_soak_maximum_first_layer_duration)|default(1800)|int %}
	{% if params2.QUALITY is defined %}
	{% set quality = params2.QUALITY|int %}
	{% if quality < 1 or quality > 5 %}
	{ action_raise_error("QUALITY must be between 1 (rough) and 5 (maximum). Use 3 (normal) if unsure.") }
	{% endif %}
	{% else %}
	{% set quality = default_quality %}
	{% endif %}
	{% if params2.FIRST_LAYER_DURATION is defined %}
	{% set first_layer_duration_mins = params2.FIRST_LAYER_DURATION|float %}
	{% if first_layer_duration_mins <= 0 %}
	{ action_raise_error("FIRST_LAYER_DURATION must be a positive number specifying the maximum first layer duration in minutes.") }
	{% endif %}
	{% if first_layer_duration_mins > 120 %}
	CONSOLE_ECHO MSG="FIRST_LAYER_DURATION will be limited to 120 minutes. Values larger than this will not have an effect on soak time."
	{% set first_layer_duration_mins = 120 %}
	{% endif %}
	{% set first_layer_duration_secs = (first_layer_duration_mins * 60.0)|int %}
	{% else %}
	{% set first_layer_duration_secs = default_first_layer_duration_secs %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	{% endif %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=True beacon_adaptive_heat_soak_layer_quality={quality} beacon_adaptive_heat_soak_maximum_first_layer_duration={first_layer_duration_secs}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."

[gcode_macro USE_FIXED_HEATSOAK]
description = Temporarily enables fixed bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
	Optionally specify DURATION (in minutes). Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.DURATION|default("0..720 minutes") %}
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_duration = (settings.variable_bed_heat_soak_time if defsrc == 'startup' else current.bed_heat_soak_time)|default(0)|int %}
	{% if params2.DURATION is defined %}
	{% set duration_mins = params2.DURATION|float %}
	{% if duration_mins < 0 %}
	{ action_raise_error("DURATION must be a non-negative number specifying the heatsoak duration in minutes.") }
	{% endif %}
	{% if duration_mins > 720 %}
	CONSOLE_ECHO MSG="DURATION will be limited to 720 minutes (12 hours). If you really need a larger value, adjust printer.cfg instead."
	{% set duration_mins = 720 %}
	{% endif %}
	{% set duration_secs = (duration_mins * 60.0)|int %}
	{% else %}
	{% set duration_secs = default_duration %}
	{% set duration_mins = duration_secs / 60.0 %}
	{% endif %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% if has_beacon %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=False bed_heat_soak_time={duration_secs}
	{% else %}
	HEATSOAK_SETTINGS QUIET=1 bed_heat_soak_time={duration_secs}
	{% endif %}
	{% if duration_mins < 1e-3 %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% else %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% endif %}

[gcode_macro USE_NO_HEATSOAK]
description = Temporarily disables bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
gcode = 
	USE_FIXED_HEATSOAK DURATION=0

[gcode_macro HEATSOAK_SETTINGS]
description = Shows or adjusts heatsoak settings
	- With no arguments: shows current heatsoak settings, specify VERBOSE=1 for detailed output
	- With arguments: sets the specified settings. Use the full setting name without the variable_ prefix, e.g. bed_heat_soak_time=300 or beacon_adaptive_heat_soak_layer_quality=4. See printer.cfg for available settings.
variable_default_source = "startup"
gcode = 
	
	{% set params2 = params %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% set quiet = params2.pop("QUIET", None)|default("0") in ("1", "true", "yes") %}
	{% set verbose = params2.pop("VERBOSE", None)|default("0") in ("1", "true", "yes") %}
	{% if has_beacon %}
	{% set vars = (
	"beacon_adaptive_heat_soak",
	"beacon_adaptive_heat_soak_max_wait",
	"beacon_adaptive_heat_soak_extra_wait_after_completion",
	"beacon_adaptive_heat_soak_layer_quality",
	"beacon_adaptive_heat_soak_maximum_first_layer_duration",
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% else %}
	{% set vars = (
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% endif %}
	{% set action = "show" if params|length == 0 else params2.ACTION %}
	{% if action is defined and params|length > 1 %}
	{ action_raise_error("ACTION cannot be specified with other parameters.") }
	{% elif action is not defined %}
	{% for k, v in params2.items() %}
	{% set k = k|lower %}
	{% if k in vars %}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Setting {k} to {v}"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={k} VALUE={v}
	{% else %}
	{ action_raise_error("Parameter '%s' is not recognised. Note that adaptive heatsoaking settings can only be set when a beacon probe is configured." % k) }
	{% endif %}
	{% endfor %}
	{% elif action == "reset" %}
	_RESET_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	CONSOLE_ECHO MSG="Heatsoak settings have been reset to their original values."
	{% elif action == "show" %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% set is_adaptive = False if not has_beacon else current.beacon_adaptive_heat_soak|default("")|lower == "true" %}
	{% if is_adaptive %}
	{% set quality = current.beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set first_layer_duration_secs = current.beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."
	{% elif current.bed_heat_soak_time|default(0)|int > 0 %}
	{% set duration_mins = (current.bed_heat_soak_time|int / 60.0) %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% else %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% endif %}
	{% if verbose %}
	CONSOLE_ECHO MSG="Detailed settings:"
	_SHOW_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	{% endif %}
	{% else %}
	{ action_raise_error("Action '%s' is not recognised" % action) }
	{% endif %}

[gcode_macro _LED_START_PRINTING]
gcode = 
	_LED_ACTION

[gcode_macro _LED_START_PRINTING_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_PRINTING]
gcode = 
	_LED_ON TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_PAUSE]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_ON]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_OFF]
gcode = 
	_LED_STANDBY

[gcode_macro _LED_LOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_LOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_RUNOUT]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_CLOG]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_UNLOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_UNLOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_DEACTIVATE_TOOLHEAD]
gcode = 
	_LED_OFF TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_STANDBY]
gcode = 
	_LED_STANDBY TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_WAKEUP]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_MOTORS_OFF]
gcode = 
	_LED_STANDBY
	_LED_VAOC_OFF

[gcode_macro _LED_INPUT_SHAPER_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_INPUT_SHAPER_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_BEACON_CALIBRATION_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_VAOC_ON]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=1.0 GREEN=1.0 BLUE=1.0
	{% endif %}

[gcode_macro _LED_VAOC_OFF]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=0.0 GREEN=0.0 BLUE=0.0
	{% endif %}

[gcode_macro _LED_ACTION]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_action %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SUCCESS]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_success %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_HEATING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_heating %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_COOLING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_cooling %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ERROR]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_error %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ON]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_on %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_OFF]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_off %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_STANDBY]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_standby %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}
	
	{% if toolhead >= 0 %}
	{% if printer['neopixel nozzle_led_t%s' % toolhead] is defined  %}
	SET_LED LED={'nozzle_led_t%s' % toolhead} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% else %}
	{% if printer['neopixel nozzle_led_t0'] is defined  %}
	SET_LED LED={'nozzle_led_t0'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% if printer['neopixel nozzle_led_t1'] is defined %}
	SET_LED LED={'nozzle_led_t1'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% endif %}
	
	_USER_LED_SET { rawparams }

[gcode_macro _USER_LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}

[gcode_macro LOAD_FILAMENT]
description = Loads new filament. Note: be careful with PETG, make sure you inspect the tip of your filament before loading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% if filament_name == '' or filament_type == '' %}
	{% set filament_name = 'unknown' %}
	{% set filament_type = 'unknown' %}
	{% endif %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_LOAD_FILAMENT TEMP={temp} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_LOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_LOAD_FILAMENT]
description = Load filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_LOAD_FILAMENT" MSG="TEMP={temp}"
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=load_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	_LOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	
	
	RESTORE_GCODE_STATE NAME=load_state
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament load routine complete, please check that the filament was loaded correctly."

[gcode_macro _IDEX_LOAD_FILAMENT]
description = Load filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament into T{toolhead}..."
	
	DEBUG_ECHO PREFIX="_IDEX_LOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	_LOAD_FILAMENT TOOLHEAD={toolhead} TEMP={temp} AUTOMATED={automated}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="Filament load routine for T{toolhead} complete, please check that the filament was loaded correctly."

[gcode_macro _LOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default(false)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE TOOLHEAD={toolhead}
	_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into hotend.."
	G92 E0
	G0 E{extruder_gear_to_cooling_position_distance} F{extruder_load_speed}
	G92 E0
	M400
	RATOS_ECHO MSG="Filament loaded into hotend."

[gcode_macro _LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set load_speed = printer["gcode_macro T%s" % toolhead].filament_load_speed|float * 60 %}
	{% set filament_loading_nozzle_offset = printer["gcode_macro T%s" % toolhead].filament_loading_nozzle_offset|float %}
	{% set cooling_position_to_nozzle_distance = printer["gcode_macro T%s" % toolhead].cooling_position_to_nozzle_distance|float %}
	{% set purge_after_load = printer["gcode_macro T%s" % toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into nozzle... Please wait!"
	G92 E0
	
	G0 E{cooling_position_to_nozzle_distance + filament_loading_nozzle_offset} F{load_speed}
	G92 E0
	G4 P1000
	_PURGE_FILAMENT	TOOLHEAD={toolhead} E={purge_after_load}
	RATOS_ECHO MSG="Filament loaded into nozzle!"

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"
	
	
	{% set filament_grabbing_length = printer["gcode_macro T%s" % toolhead].filament_grabbing_length|float %}
	{% set filament_grabbing_speed = printer["gcode_macro T%s" % toolhead].filament_grabbing_speed|float %}
	{% set resume_after_insert = true if printer["gcode_macro T%s" % toolhead].resume_after_insert|default(true)|lower == 'true' else false %}
	{% set enable_insert_detection = true if printer["gcode_macro T%s" % toolhead].enable_insert_detection|default(true)|lower == 'true' else false %}
	
	
	{% set current_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	
	{% if enable_insert_detection %}
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="toolhead: {toolhead}, filament_grabbing_length: {filament_grabbing_length}, filament_grabbing_speed: {filament_grabbing_speed}, current_idex_mode: {current_idex_mode}"
	
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	RATOS_ECHO MSG="Filament inserted into T{toolhead}, loading..."
	
	
	FORCE_MOVE STEPPER={'extruder%s' % ('' if toolhead == 0 else toolhead)} DISTANCE={filament_grabbing_length} VELOCITY={filament_grabbing_speed}
	M400
	
	
	{% if printer.pause_resume.is_paused %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% if resume_after_insert %}
	RESUME
	{% endif %}
	{% else %}
	{% if not printer.virtual_sdcard.is_active %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"

[gcode_macro _PURGE_BEFORE_UNLOAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set purge_before_unload = printer["gcode_macro T%s" % toolhead].purge_before_unload|float %}
	
	DEBUG_ECHO PREFIX="_PURGE_BEFORE_UNLOAD" MSG="TOOLHEAD: {toolhead}"
	
	
	{% if purge_before_unload > 0 %}
	G92 E0
	G0 E{purge_before_unload} F300
	G92 E0
	M400
	{% endif %}

[gcode_macro _PURGE_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set e = params.E|int %}
	{% set r = params.R|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_PURGE_FILAMENT" MSG="TOOLHEAD: {toolhead}, E: {e}"
	
	
	{% if e > 0 %}
	
	
	G92 E0
	G0 E{e} F300
	G92 E0
	M400
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={0.4 if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={0.4 if toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * 0.4)}
	{% endif %}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if r > 0 %}
	G92 E0
	G0 E-{r} F300
	G92 E0
	M400
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro _MOVE_TO_LOADING_POSITION]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_MOVE_TO_LOADING_POSITION" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	
	G1 X{loading_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _CLEANING_MOVE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_CLEANING_MOVE" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].parking_position is defined and printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set parking_position = printer["gcode_macro T%s" % toolhead].parking_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	{% set cleaning_position = loading_position %}
	{% if loading_position == parking_position %}
	{% if loading_position > 0 %}
	{% set cleaning_position = loading_position - 30 %}
	{% else %}
	{% set cleaning_position = loading_position + 30 %}
	{% endif %}
	{% endif %}
	
	
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _BED_MESH_SANITY_CHECK]
gcode = 
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is defined %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_start_print_true_zero_fuzzy_position %}
	CONSOLE_ECHO TYPE="error" TITLE="Defined zero reference not compatible with fuzzy true zero" MSG="Using fuzzy start print true zero position is not compatible with a defined zero_reference_position value in the [bed_mesh] section in printer.cfg._N_Please remove the zero_reference_position value from the [bed_mesh] section, or disable fuzzy true zero position in printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_start_print_true_zero_fuzzy_position: False"
	_STOP_AND_RAISE_ERROR MSG="Defined zero reference not compatible with fuzzy true zero"
	{% elif zero_ref_pos[0]|float|round != safe_home_x|float|round or zero_ref_pos[1]|float|round != safe_home_y|float|round %}
	CONSOLE_ECHO TYPE="error" TITLE="Zero reference position does not match safe home position" MSG="Please update your bed mesh zero reference position in printer.cfg, like so:_N__N_[bed_mesh]_N_zero_reference_position: {safe_home_x|float|round},{safe_home_y|float|round}_N_"
	_STOP_AND_RAISE_ERROR MSG="Zero reference position does not match safe home position"
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_bed_mesh %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact bed mesh is enabled" MSG="Beacon contact bed mesh is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_bed_mesh: False"
	{% endif %}
	
	{% if beacon_scan_method_automatic %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon 'automatic' scan method is enabled" MSG="Beacon 'automatic' scan method is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_scan_method_automatic: False"
	{% endif %}
	
	{% if beacon_contact_z_tilt_adjust %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact z-tilt adjust is enabled" MSG="Beacon contact z-tilt adjust is enabled. This is not recommended for normal use and may result in inaccurate z-tilt adjustment._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_z_tilt_adjust: False"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH]
gcode = 
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE=None
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE=None
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION {rawparams}
	{% endif %}

[gcode_macro _START_PRINT_BED_MESH]
variable_actual_true_zero_position_x = None
variable_actual_true_zero_position_y = None
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set X=[params.X0|default(-1)|float, params.X1|default(-1)|float] %}
	{% set Y=[params.Y0|default(-1)|float, params.Y1|default(-1)|float] %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_BED_MESH" MSG="idex_mode: {idex_mode}, X: {X}, Y: {Y}"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is not defined %}
	{% set zero_ref_pos = [safe_home_x if actual_true_zero_position_x is none else actual_true_zero_position_x, safe_home_y if actual_true_zero_position_y is none else actual_true_zero_position_y] %}
	{% endif %}
	
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	
	
	
	
	{% set X=[0, printable_x_max] %}
	{% endif %}
	
	
	{% set beacon_bed_mesh_scv = printer["gcode_macro RatOS"].beacon_bed_mesh_scv|default(25)|int %}
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% if printer.fastconfig.settings.beacon is defined and not beacon_contact_bed_mesh %}
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={beacon_bed_mesh_scv}
	{% endif %}
	
	
	{% set default_profile = printer["gcode_macro RatOS"].bed_mesh_profile|default('ratos') %}
	{% if printer["gcode_macro RatOS"].calibrate_bed_mesh|lower == 'true' %}
	BED_MESH_CLEAR
	{% if printer["gcode_macro RatOS"].adaptive_mesh|lower == 'true' %}
	CALIBRATE_ADAPTIVE_MESH PROFILE="{default_profile}" X0={X[0]} X1={X[1]} Y0={Y[0]} Y1={Y[1]} T={params.T|int} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={idex_mode} ZERO_REF_POS_X={zero_ref_pos[0]} ZERO_REF_POS_Y={zero_ref_pos[1]}
	{% else %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	BED_MESH_PROFILE LOAD="{default_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	
	{% elif printer["gcode_macro RatOS"].bed_mesh_profile is defined %}
	BED_MESH_CLEAR
	BED_MESH_PROFILE LOAD="{printer["gcode_macro RatOS"].bed_mesh_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"

[gcode_macro CALIBRATE_ADAPTIVE_MESH]
gcode = 
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set default_profile = params.PROFILE %}
	
	
	{% set x0 = params.X0|default(-1)|float %}
	{% set y0 = params.Y0|default(-1)|float %}
	{% set x1 = params.X1|default(-1)|float %}
	{% set y1 = params.Y1|default(-1)|float %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Received coordinates X0={x0|round(1)} Y0={y0|round(1)} X1={x1|round(1)} Y1={y1|round(1)}"
	
	{% if x0 >= x1 or y0 >= y1 %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Invalid coordinates received. Please check your slicer settings. Falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	
	
	{% if params.ZERO_REF_POS_X is defined and params.ZERO_REF_POS_Y is defined %}
	{% set zero_ref_pos_x = params.ZERO_REF_POS_X|float %}
	{% set zero_ref_pos_y = params.ZERO_REF_POS_Y|float %}
	{% if zero_ref_pos_x < x0 or zero_ref_pos_x > x1 or zero_ref_pos_y < y0 or zero_ref_pos_y > y1 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Zero reference position X={zero_ref_pos_x|round(1)} Y={zero_ref_pos_y|round(1)} is outside the mesh region, expanding mesh region to include it."
	{% set x0 = [x0, zero_ref_pos_x]|min %}
	{% set y0 = [y0, zero_ref_pos_y]|min %}
	{% set x1 = [x1, zero_ref_pos_x]|max %}
	{% set y1 = [y1, zero_ref_pos_y]|max %}
	{% endif %}
	{% endif %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float %}
	
	
	{% set mesh_x0 = [[x0, max_x]|min, min_x]|max %}
	{% set mesh_y0 = [[y0, max_y]|min, min_y]|max %}
	{% set mesh_x1 = [[x1, max_x]|min, min_x]|max %}
	{% set mesh_y1 = [[y1, max_y]|min, min_y]|max %}
	
	{% if mesh_x0 == min_x and mesh_y0 == min_y and mesh_x1 == max_x and mesh_y1 == max_y %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Print is using the full bed, falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	
	{% set probe_count_x = mesh_config.probe_count.split(",")[0]|int %}
	{% if mesh_config.probe_count.split(",")|length == 2 %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[1]|int %}
	{% else %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[0]|int %}
	{% endif %}
	
	
	{% set probe_x_step = (max_x - min_x) / probe_count_x %}
	{% set probe_y_step = (max_y - min_y) / probe_count_y %}
	
	
	{% set mesh_count_x = ([(mesh_x1 - mesh_x0) / probe_x_step, 3]|max)|int %}
	{% set mesh_count_y = ([(mesh_y1 - mesh_y0) / probe_y_step, 3]|max)|int %}
	{% set min_mesh_count = [mesh_count_x, mesh_count_y]|min %}
	{% set max_mesh_count = [mesh_count_x, mesh_count_y]|max %}
	
	
	{% set algorithm = mesh_config.algorithm %}
	{% if algorithm|lower == 'lagrange' and max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="cannot exceed a probe_count of 6 when using lagrange interpolation. Falling back to bicubic interpolation."
	{% set algorithm = 'bicubic' %}
	{% endif %}
	{% if algorithm|lower == 'bicubic' and min_mesh_count < 4 %}
	{% if max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="invalid probe_count option when using bicubic interpolation. Combination of 3 points on one axis with more than 6 on another is not permitted. Forcing minimum mesh count to be 4."
	{% set min_mesh_count = 4 %}
	{% else %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="bicubic interpolation with a probe_count of less than 4 points detected. Forcing lagrange interpolation."
	{% set algorithm = 'lagrange' %}
	{% endif %}
	{% endif %}
	
	{% set mesh_count_x = ([min_mesh_count, mesh_count_x]|max)|int %}
	{% set mesh_count_x = ([max_mesh_count, mesh_count_x]|min)|int %}
	{% set mesh_count_y = ([min_mesh_count, mesh_count_y]|max)|int %}
	{% set mesh_count_y = ([max_mesh_count, mesh_count_y]|min)|int %}
	
	{% set should_prime = printer["gcode_macro RatOS"].nozzle_priming == 'primeblob' %}
	{% if printer["dual_carriage"] is not defined %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% else %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 != 0 and probe_first %}
	{% set probe_first = false %}
	{% elif printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 == 0 and not probe_first %}
	{% set probe_first = true %}
	{% endif %}
	
	
	{% if should_prime and probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="mesh coordinates X0={mesh_x0|round(1)} Y0={mesh_y0|round(1)} X1={mesh_x1|round(1)} Y1={mesh_y1|round(1)}"
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y} RELATIVE_REFERENCE_INDEX=-1
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	
	
	{% if should_prime and not probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro M84]
rename_existing = M84.1
gcode = 
	
	M84.1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_OFFSET X=0 Y=0
	
	
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro _VAOC"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False
	{% endif %}
	
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	SET_SKEW CLEAR=1
	
	
	_LED_MOTORS_OFF

[gcode_macro M104]
rename_existing = M104.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M104" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set temperature_offset_t0 = printer["gcode_macro T0"].temperature_offset|default(0)|int %}
	{% set temperature_offset_t1 = printer["gcode_macro T1"].temperature_offset|default(0)|int %}
	{% set s0 = [s + temperature_offset_t0, 0]|max %}
	{% set s1 = [s + temperature_offset_t1, 0]|max %}
	{% if temperature_offset_t0 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t0}°C added to toolhead T0."
	{% endif %}
	{% if temperature_offset_t1 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t1}°C added to toolhead T1."
	{% endif %}
	{% else %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	M104.1 S{s0} T0
	M104.1 S{s1} T1
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% else %}
	M104.1 S{s} T{t}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M109]
rename_existing = M109.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M109" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M109" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	M109.1 S{s} T{t}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro SET_HEATER_TEMPERATURE]
rename_existing = SET_HEATER_TEMPERATURE_BASE
gcode = 
	
	{% set heater = params.HEATER|default("") %}
	{% set target = params.TARGET|default(0)|int %}
	
	DEBUG_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="heater: {heater}, target: {target}"
	
	{% set t = -1 %}
	{% if heater|lower == "extruder" or heater|lower == "extruder1" %}
	
	{% set t = 0 if heater|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and target > 0 %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set target = [target + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE_BASE HEATER="{heater}" TARGET={target}
	
	{% if t != -1 and printer.fastconfig.settings.beacon is defined %}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro TEMPERATURE_WAIT]
rename_existing = TEMPERATURE_WAIT_BASE
gcode = 
	
	{% set sensor = params.SENSOR|default("") %}
	{% set minimum = params.MINIMUM|default(-1)|int %}
	{% set maximum = params.MAXIMUM|default(-1)|int %}
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="sensor: {sensor}, minimum: {minimum}, maximum: {maximum}"
	
	{% set t = -1 %}
	{% if sensor|lower == "extruder" or sensor|lower == "extruder1" %}
	
	{% set t = 0 if sensor|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and (minimum > 0 or maximum > 0) %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% if minimum > -1 %}
	{% set minimum = [minimum + temperature_offset, 0]|max %}
	{% endif %}
	{% if maximum > -1 %}
	{% set maximum = [maximum + temperature_offset, 0]|max %}
	{% endif %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set id = "sensor " ~ sensor if t == -1 else "toolhead T" ~ t %}
	
	
	{% if minimum > -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum} MAXIMUM={maximum}
	{% elif minimum > -1 and maximum == -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum}
	{% elif minimum == -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MAXIMUM={maximum}
	{% else %}
	
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="neither MINIMUM or MAXIMUM args were specified, call TEMPERATURE_WAIT_BASE is expected to fail"
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}"
	{% endif %}
	
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature for {id} reached."

[gcode_macro SDCARD_PRINT_FILE]
rename_existing = SDCARD_PRINT_FILE_BASE
gcode = 
	{% if printer["ratos"] is defined %}
	PROCESS_GCODE_FILE { rawparams }
	{% else %}
	SDCARD_PRINT_FILE_BASE { rawparams }
	{% endif %}

[gcode_macro SKEW_PROFILE]
rename_existing = SKEW_PROFILE_BASE
variable_loaded_profile = ""
gcode = 
	{% if params.LOAD is defined %}
	{% if printer.fastconfig.settings["skew_correction %s" % params.LOAD] is defined %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='"{params.LOAD}"'
	{% endif %}
	{% endif %}
	
	SKEW_PROFILE_BASE { rawparams }

[gcode_macro SET_SKEW]
rename_existing = SET_SKEW_BASE
gcode = 
	{% if params.CLEAR is defined %}
	{% if params.CLEAR|default(0)|int == 1 %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='""'
	{% endif %}
	{% endif %}
	
	SET_SKEW_BASE { rawparams }

[gcode_macro SET_VELOCITY_LIMIT]
rename_existing = SET_VELOCITY_LIMIT_BASE
gcode = 
	{% if params.ACCEL_TO_DECEL is defined %}
	
	{% if params.ACCEL is defined %}
	{% set accel = params.ACCEL|float %}
	{% else %}
	{% set accel = printer.toolhead.max_accel|float %}
	{% endif %}
	
	{% if params.VELOCITY is defined %}
	{% set velocity = params.VELOCITY|float %}
	{% else %}
	{% set velocity = printer.toolhead.max_velocity|float %}
	{% endif %}
	
	{% if params.SQUARE_CORNER_VELOCITY is defined %}
	{% set scv = params.SQUARE_CORNER_VELOCITY|float %}
	{% else %}
	{% set scv = printer.toolhead.square_corner_velocity|float %}
	{% endif %}
	
	{% set mcr = params.ACCEL_TO_DECEL|float / accel %}
	
	DEBUG_ECHO PREFIX="SET_VELOCITY_LIMIT" MSG="ACCEL={accel}, VELOCITY={velocity}, SQUARE_CORNER_VELOCITY={scv}, MINIMUM_CRUISE_RATIO={mcr}"
	
	SET_VELOCITY_LIMIT_BASE ACCEL={accel} VELOCITY={velocity} SQUARE_CORNER_VELOCITY={scv} MINIMUM_CRUISE_RATIO={1-mcr}
	
	{% else %}
	
	SET_VELOCITY_LIMIT_BASE { rawparams }
	
	{% endif %}

[gcode_macro BED_MESH_CALIBRATE]
rename_existing = _BED_MESH_CALIBRATE_BASE
variable_abl_and_home_z_if_required = True
gcode = 
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	{% if abl_and_home_z_if_required %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% endif %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set beacon_default_probe_method = printer.fastconfig.settings.beacon.default_probe_method|default('proximity') %}
	{% set probe_method = params.PROBE_METHOD|default(beacon_default_probe_method)|lower %}
	{% if probe_method == 'proximity' %}
	_CHECK_ACTIVE_BEACON_MODEL_TEMP TITLE="Bed mesh calibration warning"
	{% endif %}
	{% endif %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_BED_MESH_CALIBRATE_BASE {rawparams}
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	_APPLY_RATOS_BED_MESH_PARAMETERS {rawparams}
	{% endif %}

[gcode_macro SET_GCODE_OFFSET]
rename_existing = SET_GCODE_OFFSET_BASE
gcode = 
	DEBUG_ECHO PREFIX="SET_GCODE_OFFSET" MSG="{rawparams|replace('"', '')|replace("'", '')}"
	{% set z_before = printer.gcode_move.homing_origin.z|float %}
	SET_GCODE_OFFSET_BASE {rawparams}
	_AFTER_SET_GCODE_OFFSET Z_BEFORE={z_before}

[gcode_macro _AFTER_SET_GCODE_OFFSET]
gcode = 
	{% set z_before = params.Z_BEFORE|float %}
	{% set z_after = printer.gcode_move.homing_origin.z|float %}
	{% if z_before != z_after %}
	_ALERT_NON_ZERO_Z_OFFSET FORCE=1
	{% endif %}

[gcode_macro _START_PRINT_PARK]
gcode = 
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_x = printer["gcode_macro RatOS"].start_print_park_x %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% if printer["gcode_macro RatOS"].start_print_park_x is defined and printer["gcode_macro RatOS"].start_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="start_print_park_x is ignored for IDEX printers"
	{% endif %}
	PARK_TOOLHEAD
	G90
	{% endif %}
	
	
	_PARK LOCATION={start_print_park_in} X={start_print_park_x}
	G0 Z{z} F{z_speed}

[gcode_macro _END_PRINT_PARK]
gcode = 
	{% if printer["dual_carriage"] is defined %}
	
	{% if printer["gcode_macro RatOS"].end_print_park_x is defined and printer["gcode_macro RatOS"].end_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="end_print_park_x is ignored for IDEX printers"
	{% endif %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	PARK_TOOLHEAD
	G90
	{% endif %}
	_PARK LOCATION={printer["gcode_macro RatOS"].end_print_park_in} X={printer["gcode_macro RatOS"].end_print_park_x}

[gcode_macro _PARK]
gcode = 
	
	{% set x = params.X %}
	{% set location = params.LOCATION|default('back')|lower %}
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	{% set nozzle_priming = printer["gcode_macro RatOS"].nozzle_priming|lower %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="park"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% if x != '' %}
	{% if x|float >= printer.toolhead.axis_minimum.x + 5 and x|float <= printable_x_max - 5 %}
	{% set park_x = x|float %}
	{% else %}
	{action_respond_info('The requested X co-ordinate is outside the defined axis bounds - using defaults')}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	{% else %}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	
	
	{% set park_y = printable_y_max - 15 %}
	{% if location == 'front' %}
	{% set park_y = printer.toolhead.axis_minimum.y + 5 %}
	{% elif location == 'center' %}
	{% set park_y = printable_y_max / 2 %}
	{% elif location == 'primeblob' and printer["dual_carriage"] is defined %}
	
	{% set park_y = printable_y_max - 15 %}
	{% endif %}
	
	
	{% if location == 'primeblob' and printer["dual_carriage"] is not defined %}
	{% if (nozzle_priming == 'primeblob' or nozzle_priming == 'primeline') %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set park_x = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set park_x = printable_x_max - 5 %}
	{% else %}
	{% set park_x = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set park_y = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set park_y = printable_y_max - 5 %}
	{% else %}
	{% set park_y = nozzle_prime_start_y|float %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	G0 X{park_x} Y{park_y} F{speed}
	{% else %}
	
	G0 Y{park_y} F{speed}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="park"

[gcode_macro SAVE_PROBE_RESULT]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	{% set last_z_offset = 9999.9 %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if beacon_contact_prime_probing %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	{% else %}
	{% set last_z_offset = printer.beacon.last_sample.dist - current_z %}
	{% endif %}
	{% elif printer.fastconfig.settings.bltouch is defined  %}
	{% set config_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% elif printer.fastconfig.settings.probe is defined  %}
	{% set config_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% endif %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Saving offset adjustment of {last_z_offset} in {params.VARIABLE|default('last_z_offset')}"
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={params.VARIABLE|default('last_z_offset')} VALUE={last_z_offset}

[gcode_macro PROBE_FOR_PRIMING]
gcode = 
	
	{% set probe_for_priming_disable_mesh_constraints = true if printer["gcode_macro RatOS"].probe_for_priming_disable_mesh_constraints|default(false)|lower == 'true' else false %}
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower != 'false' %}
	SAVE_GCODE_STATE NAME=probe_for_priming_state
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the prime location.."
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set t = params.TOOLHEAD|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% if idex_mode == '' %}
	
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% if t == 0 %}
	{% set x_start = 5 %}
	{% else %}
	{% set x_start = printable_x_max - 5 %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% endif %}
	{% endif %}
	{% set z = printer.fastconfig.settings.bed_mesh.horizontal_move_z|float %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% if printer.fastconfig.settings.bltouch is defined %}
	{% set x_offset = printer.fastconfig.settings.bltouch.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.bltouch.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% elif printer.fastconfig.settings.probe is defined %}
	{% set x_offset = printer.fastconfig.settings.probe.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.probe.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% elif printer.fastconfig.settings.beacon is defined %}
	{% set x_offset = printer.fastconfig.settings.beacon.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.beacon.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.beacon.trigger_distance|float %}
	{% else %}
	{ action_raise_error("No probe, beacon or bltouch section found. Adaptive priming only works with a [probe], [beacon] or [bltouch] section defined.") }
	{% endif %}
	
	{% if z < z_offset %}
	{ action_raise_error("Horizontal move Z ({z}) is below your probe's Z offset ({z_offset}). Please adjust your horizontal_move_z setting in [bed_mesh] to be above {z}.") }
	{% endif %}
	
	{% if not probe_for_priming_disable_mesh_constraints %}
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float - x_offset %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float - y_offset %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float - x_offset %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float - y_offset %}
	
	
	{% set x_start = [[x_start, max_x]|min, min_x]|max %}
	{% set y_start = [[y_start, max_y]|min, min_y]|max %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the start of the prime location at {x_start}, {y_start}"
	
	G90
	
	M83
	
	G0 Z{z} F{z_speed}
	
	G1 X{x_start} Y{y_start} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result
	{% endif %}
	
	{% if idex_mode == '' %}
	
	{% set x_end = x_start %}
	{% set y_end = y_start + 45 %}
	{% else %}
	
	{% if t==1 %}
	{% set x_end = x_start - 45 %}
	{% else %}
	{% set x_end = x_start + 45 %}
	{% endif %}
	{% set y_end = y_start %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the end of the prime location at {x_end}, {y_end}"
	G1 X{x_end} Y{y_end} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result
	{% endif %}
	
	RESTORE_GCODE_STATE NAME=probe_for_priming_state
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	{% endif %}

[gcode_macro RESET_PRIME_PROBE_STATE]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result VALUE=None
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result_t1 VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result_t1 VALUE=None
	{% endif %}

[gcode_macro PROBE_CURRENT_POSITION]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	SAVE_GCODE_STATE NAME=probe_current_position_state
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	ASSERT_PROBE_DEPLOYED
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_prime_probing %}
	PROBE PROBE_METHOD=contact SAMPLES=1
	{% else %}
	PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	BEACON_QUERY
	{% else %}
	
	RESTORE_GCODE_STATE NAME=probe_current_position_state MOVE=1 MOVE_SPEED={printer["gcode_macro RatOS"].macro_z_speed|float}
	{% endif %}

[gcode_macro PRIME_BLOB]
description = Prints a primeblob, used internally, if configured, as part of the START_PRINT macro.
variable_x_offset = 5
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="prime_blob"
	SET_MACRO_TRAVEL_SETTINGS
	
	RATOS_ECHO PREFIX="Priming" MSG="Priming nozzle with prime blob.."
	
	
	{% set current_toolhead = 0 %}
	
	
	{% set target_idex_mode = '' %}
	{% set extruder = 'extruder' %}
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE is defined %}
	{% set target_idex_mode = params.IDEX_MODE|default('')|lower %}
	{% else %}
	{ action_raise_error("IDEX_MODE parameter not found for PRIME_BLOB macro. This is likely a bug.") }
	{% endif %}
	RATOS_ECHO PREFIX="Priming" MSG="Priming in IDEX {target_idex_mode} mode.."
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set current_toolhead = 1 if current_idex_mode=='primary' else 0 %}
	{% set extruder = 'extruder1' if current_toolhead == 1 else 'extruder' %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	SAVE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set fan_speed = printer["gcode_macro RatOS"].nozzle_prime_bridge_fan|float %}
	{% set nozzle_diameter = printer.fastconfig.settings[extruder].nozzle_diameter|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set has_start_offset_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) != 9999.9 %}
	{% if printer["dual_carriage"] is defined %}
	{% set has_start_offset_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) != 9999.9 %}
	{% endif %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_z_height = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set nozzle_prime_direction = printer["gcode_macro RatOS"].nozzle_prime_direction|lower %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% if target_idex_mode == '' %}
	
	{% set x_factor = 0 %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% set y_factor = -1 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% if nozzle_prime_start_y|float < printable_y_max / 2 %}
	{% set y_factor = 1 %}
	{% else %}
	{% set y_factor = -1 %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_direction == 'forwards' %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_direction == 'backwards' %}
	{% set y_factor = -1 %}
	{% endif %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% else %}
	{% set z = start_print_park_z_height %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% set y_factor = 0 %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set x_start = center_x / 2 + 5 %}
	{% set x_factor = 1 %}
	{% else %}
	
	
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% if current_toolhead == 0 %}
	{% set x_start = 55 %}
	{% set x_factor = -1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 55 %}
	{% set x_factor = 1 %}
	{% endif %}
	{% else %}
	{% if current_toolhead == 0 %}
	{% set x_start = 5 %}
	{% set x_factor = 1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 5 %}
	{% set x_factor = -1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_x_max - 5 %}
	{% endif %}
	{% set z = 10 %}
	{% endif %}
	
	{% set start_z_offset = 0 %}
	{% set end_z_offset = 0 %}
	{% if has_start_offset_t0 %}
	{% set start_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) %}
	{% set end_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_end_result|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t0) ) }
	{% endif %}
	{% if end_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t0) )  }
	{% endif %}
	{% set start_z_offset = start_z_probe_result_t0 %}
	{% set end_z_offset = end_z_probe_result_t0 %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	{% if current_toolhead == 1 or both_toolheads or target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	{% if has_start_offset_t1 %}
	{% set start_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) %}
	{% set end_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_end_result_t1|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t1) ) }
	{% endif %}
	{% if end_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t1) ) }
	{% endif %}
	{% set start_z_offset = [start_z_offset, start_z_probe_result_t1]|max %}
	{% set end_z_offset = [end_z_offset, start_z_probe_result_t1]|max %}
	{% endif %}
	{% endif %}
	{% if target_idex_mode != 'copy' and target_idex_mode != 'mirror' %}
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% set original_start_z_offset = start_z_offset %}
	{% set original_end_z_offset = end_z_offset %}
	{% set start_z_offset = original_end_z_offset %}
	{% set end_z_offset = original_start_z_offset %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	DEBUG_ECHO PREFIX="PRIME_BLOB" MSG="x_start: {x_start}, y_start: {y_start}, x_factor: {x_factor}, y_factor: {y_factor}, z: {z}, start_z_offset: {start_z_offset}, end_z_offset: {end_z_offset}"
	
	
	G90
	
	M83
	RATOS_ECHO PREFIX="Priming" MSG="Lifting Z to {z}.."
	
	G0 Z{z} F{z_speed}
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% if start_print_park_in != 'primeblob' %}
	G1 X{x_start} F{speed}
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% endif %}
	{% else %}
	
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% if target_idex_mode=="copy" or target_idex_mode=="mirror" %}
	RATOS_ECHO PREFIX="Priming" MSG="Mirroring move to {x_start}, {y_start} along the edge of the print area.."
	
	_IDEX_MIRROR PRIMING=1
	{% else %}
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% endif %}
	G1 X{x_start} F{speed}
	{% endif %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Starting prime blob.."
	
	G1 Z{0.5 + start_z_offset} F{z_speed}
	
	G1 Y{y_start} F{speed}
	
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	
	M106 S{fan_speed}
	
	G1 Z5 F100 E5
	G92 E0
	RATOS_ECHO PREFIX="Priming" MSG="Bridging with {((fan_speed/255) * 100)|int}% fan speed.."
	
	G1 F3000 X{x_start + (15 * x_factor)} Y{y_start + (15 * y_factor)} E{1 / ((0.4 / nozzle_diameter) ** 2)}
	
	
	
	G1 F3000 X{x_start + (20 * x_factor)} Y{y_start + (20 * y_factor)} Z{3.8 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (34 * x_factor)} Y{y_start + (34 * y_factor)} Z{2.6 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (38 * x_factor)} Y{y_start + (38 * y_factor)} Z{1.4 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (42 * x_factor)} Y{y_start + (42 * y_factor)} Z{0.2 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	
	M106 S0
	
	G1 F3000 X{x_start + (46 * x_factor)} Y{y_start + (46 * y_factor)} Z{0.2 + end_z_offset} E0.6
	
	G1 F{speed} X{x_start + (50 * x_factor)} Y{y_start + (50 * y_factor)}
	
	
	{% if target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if target_idex_mode == "copy" %}
	{% if first_y >= 0 %}
	_IDEX_COPY DANCE=0 Y={first_y}
	{% else %}
	_IDEX_COPY DANCE=0 Y={params.Y1}
	{% endif %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	RESTORE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="prime_blob"
	
	
	G92 E0

[gcode_macro UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set temp = params.TEMP|default(220)|int %}
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_UNLOAD_FILAMENT TEMP={temp} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_UNLOAD_FILAMENT]
description = Unload filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_UNLOAD_FILAMENT" MSG="TEMP: {temp}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=unload_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	G4 P3000
	
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD=0 NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=unload_state
	
	
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament unloading completed"

[gcode_macro _IDEX_UNLOAD_FILAMENT]
description = Unload filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading T{toolhead} filament..."
	
	DEBUG_ECHO PREFIX="_IDEX_UNLOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} AUTOMATED={automated}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="T{toolhead} filament unloading completed"

[gcode_macro _UNLOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LEGACY_UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
gcode = 
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set unload_speed = 5 * 60 %}
	{% set unload_length = printer["gcode_macro RatOS"].filament_unload_length|float %}
	M117 Unloading filament...
	
	G0 E10 F300
	
	G0 E-5 F3600
	
	G4 P3000
	
	G0 E5 F6000
	
	G0 E-15 F6000
	
	G0 E-{unload_length} F{unload_speed}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}
	M117 Filament unloaded!
	RESPOND MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	RATOS_ECHO MSG="Unloading filament from nozzle to cooling zone... Please wait!"
	
	_PURGE_BEFORE_UNLOAD TOOLHEAD={toolhead}
	
	{% if printer["gcode_macro _UNLOAD_WITHOUT_TIP_FORMING"] is defined %}
	
	_UNLOAD_WITHOUT_TIP_FORMING TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	_UNLOAD_WITH_TIP_FORMING NAME='{filament_name}' TYPE='{filament_type}'
	{% endif %}
	
	G4 P3000

[gcode_macro _UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	{% set tooolhead_sensor_to_extruder_gear_distance = printer["gcode_macro T%s" % toolhead].tooolhead_sensor_to_extruder_gear_distance|float %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER" MSG="TOOLHEAD: {toolhead}"
	
	
	G0 E-{extruder_gear_to_cooling_position_distance + tooolhead_sensor_to_extruder_gear_distance + 50} F{extruder_load_speed}
	
	RATOS_ECHO MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_WITH_TIP_FORMING]
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	{% if filament_name != '' and filament_type != '' %}
	_UNLOAD_KNOWN_FILAMENT NAME={filament_name} TYPE={filament_type}
	{% else %}
	_UNLOAD_UNKNOWN_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _UNLOAD_KNOWN_FILAMENT]
description = User overrideable tip forming macro if slicer filament profiles are known
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	RATOS_ECHO PREFIX="FILAMENT TYPE" MSG='{filament_type}'
	RATOS_ECHO PREFIX="FILAMENT PROFILE" MSG='{filament_name}'
	
	
	{% if filament_name == "Prusament PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% elif filament_name == "Nobufil PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% else %}
	
	RATOS_ECHO PREFIX="_UNLOAD_KNOWN_FILAMENT" MSG="Filament profile not found!"
	_UNLOAD_UNKNOWN_FILAMENT
	{% endif %}

[gcode_macro _UNLOAD_UNKNOWN_FILAMENT]
description = User overrideable standard tip forming macro
gcode = 
	
	DEBUG_ECHO PREFIX="_UNLOAD_UNKNOWN_FILAMENT" MSG="Using standard tip forming macro!"
	
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10

[gcode_macro _TIP_FORMING]
gcode = 
	
	{% set cooling_moves = params.COOLING_MOVES|default(4)|int %}
	{% set cooling_move_length = params.COOLING_MOVE_LENGTH|default(10)|float %}
	{% set start_cooling_speed = params.START_COOLING_SPEED|default(10)|float * 60 %}
	{% set end_cooling_speed = params.END_COOLING_SPEED|default(50)|float * 60 %}
	{% if cooling_moves == 0 %}
	{% set cooling_move_length = 0 %}
	{% endif %}
	
	
	{% set dip = true if params.DIP|default(false)|lower == "true" else false %}
	{% set dip_length = params.DIP_LENGTH|default(22)|float %}
	{% set dip_speed = params.DIP_SPEED|default(30)|float * 60 %}
	{% set dip_retract_speed = params.DIP_RETRACT_SPEED|default(70)|float * 60 %}
	
	
	{% set retract_length = params.RETRACT_LENGTH|default(18)|float %}
	{% set start_retract_speed = params.START_RETRACT_SPEED|default(120)|float * 60 %}
	{% set end_retract_speed = params.END_RETRACT_SPEED|default(20)|float * 60 %}
	
	DEBUG_ECHO PREFIX="_TIP_FORMING" MSG="cooling_moves: {cooling_moves}, cooling_move_length: {cooling_move_length}, start_cooling_speed: {start_cooling_speed}, end_cooling_speed: {end_cooling_speed}, dip: {dip}, dip_length: {dip_length}, dip_speed: {dip_speed}, dip_retract_speed: {dip_retract_speed}, retract_length: {retract_length}, start_retract_speed: {start_retract_speed}, end_retract_speed: {end_retract_speed}"
	
	M220 S100
	
	
	G92 E0
	{% set retract = retract_length + cooling_move_length / 2 - 15 %}
	G1 E-15 F{start_retract_speed}
	G1 E-{0.7 * retract} F{1.0 * end_retract_speed}
	G1 E-{0.2 * retract} F{0.5 * end_retract_speed}
	G1 E-{0.1 * retract} F{0.3 * end_retract_speed}
	
	
	G92 E0
	{% if cooling_moves > 0 %}
	{% set i = (end_cooling_speed - start_cooling_speed) / (2 * cooling_moves - 1) %}
	{% for m in range(cooling_moves) %}
	G1 E{cooling_move_length} F{(start_cooling_speed + i * m * 2)}
	G1 E-{cooling_move_length} F{(start_cooling_speed + i * (m * 2 + 1))}
	{% endfor %}
	{% endif %}
	
	
	G92 E0
	{% if dip %}
	G1 E{dip_length} F{dip_speed}
	G4 P100
	G1 E-{dip_length} F{dip_retract_speed}
	{% endif %}
	
	G92 E0
	M400

[delayed_gcode __ON_FILAMENT_SENSOR_BUTTON_PRESSED_STARTUP_GUARD]
initial_duration = 2.
gcode = 
	SET_GCODE_VARIABLE MACRO=_ON_FILAMENT_SENSOR_BUTTON_PRESSED VARIABLE=startup_complete VALUE=True

[gcode_macro _ON_FILAMENT_SENSOR_BUTTON_PRESSED]
variable_startup_complete = False
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set toolhead_sensor_button_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_sensor_button_only_when_sensor_enabled|default(false)|lower == 'true' %}
	
	
	{% if not startup_complete and sensor_enabled %}
	{action_emergency_stop("RatOS: The T%s filament sensor button was triggered immediately on printer startup. This is likely a false trigger. Please check your filament sensor wiring and configuration!" % (toolhead,))}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_SENSOR_BUTTON_PRESSED" MSG="TOOLHEAD: {toolhead}, SENSOR_ENABLED: {sensor_enabled}, TOOLHEAD_SENSOR_BUTTON_ONLY_WHEN_SENSOR_ENABLED: {toolhead_sensor_button_only_when_sensor_enabled}"
	
	{% if not printer.virtual_sdcard.is_active and (sensor_enabled or not toolhead_sensor_button_only_when_sensor_enabled) %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	{% set toolhead_detect_clog_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_detect_clog_only_when_sensor_enabled|default(true)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}, ENABLE_CLOG_DETECTION: {enable_clog_detection}, TOOLHEAD_DETECT_CLOG_ONLY_WHEN_SENSOR_ENABLED: {toolhead_detect_clog_only_when_sensor_enabled}, SENSOR_ENABLED: {sensor_enabled}"
	
	{% if enable_clog_detection and (sensor_enabled or not toolhead_detect_clog_only_when_sensor_enabled) %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_clog_detection %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_FILAMENT_END]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set clogged = true if params.CLOGGED|default(false)|lower == 'true' else false %}
	
	
	{% set unload_after_runout = printer["gcode_macro T%s" % toolhead].unload_after_runout|float %}
	
	
	{% if clogged %}
	_LED_FILAMENT_CLOG TOOLHEAD={toolhead}
	{% else %}
	_LED_FILAMENT_RUNOUT TOOLHEAD={toolhead}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_END" MSG="TOOLHEAD: {toolhead}"
	
	{% if printer.virtual_sdcard.is_active %}
	{% if not printer.pause_resume.is_paused %}
	PAUSE RUNOUT=True
	{% endif %}
	{% if not clogged and unload_after_runout %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	{% if not clogged and printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true'%}
	_JOIN_SPOOL TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M600]
description = Executes a color change by pausing the printer an unloading the filament.
gcode = 
	PAUSE
	UNLOAD_FILAMENT AUTOMATED=True
	RATOS_ECHO MSG="Please load new filament and resume"

[gcode_macro COLD_PULL]
description = Automated hotend cold pull.
gcode = 
	
	{% set extrusion_temp = params.EXTRUSION_TEMP|default(220)|int %}
	{% set cold_pull_temp = params.COLD_PULL_TEMP|default(80)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	
	{% if printer["dual_carriage"] is not defined %}
	{% set toolhead = 0 %}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead != 0 and toolhead != 1 %}
	{action_raise_error("Please select toolhead! 0 = left, 1 = right toolhead")}
	{% endif %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	RATOS_ECHO MSG="Starting cold pull on T{toolhead}..."
	{% else %}
	RATOS_ECHO MSG="Starting cold pull..."
	{% endif %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	SAVE_GCODE_STATE NAME=cold_pull_state
	
	
	{% if printer["dual_carriage"] is defined and "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	RATOS_ECHO MSG="Heating T{toolhead} to {extrusion_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={extrusion_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={extrusion_temp} MAXIMUM={extrusion_temp + 2}
	
	
	G4 P3000
	
	
	RATOS_ECHO MSG="extruding..."
	G92 E0
	G1 E30 F300
	G92 E0
	
	
	RATOS_ECHO MSG="Cooling T{toolhead} to {cold_pull_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={cold_pull_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={cold_pull_temp} MAXIMUM={cold_pull_temp + 2}
	
	
	G4 P10000
	
	
	RATOS_ECHO MSG="cold pull..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-40 VELOCITY=5 ACCEL=100
	
	
	RATOS_ECHO MSG="eject filament..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-200 VELOCITY=20 ACCEL=500
	
	
	RATOS_ECHO MSG="cooling down extruder..."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	RESTORE_GCODE_STATE NAME=cold_pull_state
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	
	CONSOLE_ECHO TITLE="Cold pull complete" MSG="Please remove the filament from the PTFE tube and cut the end off. Do NOT try to load it again." TYPE="warning"

[gcode_macro _USER_START_PRINT_BEFORE_HOMING]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_BED]
gcode = 

[gcode_macro _USER_START_PRINT_BED_MESH]
gcode = 

[gcode_macro _USER_START_PRINT_PARK]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 

[gcode_macro _USER_START_PRINT_HEAT_CHAMBER]
description = Uses the extruder sensor to wait for chamber temp. Override the _START_PRINT_HEAT_CHAMBER macro to implement heated chamber handling.
gcode = 
	
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}

[gcode_macro _USER_END_PRINT_BEFORE_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_AFTER_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_PARK]
gcode = 

[gcode_macro _USER_END_PRINT_FINISHED]
description = User hook for when the print is finished after gcode state has been restored.
gcode = 

[gcode_macro _USER_START_PRINT]
gcode = 

[gcode_macro _USER_END_START_PRINT]
gcode = 

[gcode_macro _USER_START_FEATURE]
gcode = 

[gcode_macro _USER_END_FEATURE]
gcode = 

[gcode_macro _USER_BEFORE_IDLE_TIMEOUT]
gcode = 

[gcode_macro _USER_AFTER_IDLE_TIMEOUT]
gcode = 

[gcode_macro ECHO_T_VARS]
description = Echo Toolhead variables to the console.
gcode = 
	{% set t = params.T|default(0) %}
	RATOS_ECHO MSG="T{t} Variables"
	{% for var, value in printer["gcode_macro T%s" % t].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ECHO_RATOS_VARS]
description = Echo RatOS variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro RatOS"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ENSURE_CRITICAL_RATOS_INIT]
variable_completed = False
gcode = 
	{% if not completed %}
	CALCULATE_PRINTABLE_AREA
	SET_GCODE_VARIABLE MACRO=ENSURE_CRITICAL_RATOS_INIT VARIABLE=completed VALUE=True
	{% endif %}

[delayed_gcode RATOS_INIT]
initial_duration = 0.1
gcode = 
	{action_respond_info("Initializing RatOS...")}
	ENSURE_CRITICAL_RATOS_INIT
	_LED_STANDBY
	INITIAL_FRONTEND_UPDATE
	_CHAMBER_FILTER_SANITY_CHECK
	{% if printer.fastconfig.settings.beacon is defined %}
	
	_BED_MESH_SANITY_CHECK
	{% endif %}
	{% set svv = printer.save_variables.variables %}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=0 C={svv.nozzle_expansion_coefficient_t0|default(0.06)|float}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=1 C={svv.nozzle_expansion_coefficient_t1|default(0.06)|float}
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=idex_applied_offset

[delayed_gcode RATOS_LOGO]
initial_duration = 2
gcode = 
	
	
	
	
	
	ENSURE_CRITICAL_RATOS_INIT
	HELLO_RATOS
	_ALERT_NON_ZERO_Z_OFFSET

[gcode_macro _ALERT_NON_ZERO_Z_OFFSET]
gcode = 
	{% set force = params.FORCE|default(0)|int == 1 %}
	{% set user_offset = printer.named_offsets.user_probe_z_offset.z|float %}
	{% set gcode_offset = printer.gcode_move.homing_origin.z|float %}
	{% set combined_offset = user_offset + gcode_offset %}
	
	{% if force or user_offset != 0 or gcode_offset != 0 %}
	{% set title = "User-adjusted Z-offset of %.3f mm is active" % combined_offset %}
	{% set msg = "" %}
	{% set nl = "" %}
	{% if user_offset != 0 %}
	{% set msg = msg + "beacon true zero user Z-offset: %.3f mm (to clear, use Z_OFFSET_APPLY_PROBE CLEAR=1)" % user_offset %}
	{% set nl = "_N_" %}
	{% endif %}
	{% if gcode_offset != 0 %}
	{% set msg = msg + nl + "G-code Z-offset: %.3f mm" % gcode_offset %}
	{% endif %}
	CONSOLE_ECHO TITLE="{title}" TYPE="info" MSG="{msg}"
	{% endif %}

[gcode_macro _INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE]
gcode = 
	{% set variable = params.VARIABLE|string %}
	{% set svv = printer.save_variables.variables %}
	{% set nlu_msg = "no longer used, please remove" %}
	{% if svv[variable] is defined %}
	{% set v = svv[variable]|string|replace('"', '')|replace("'", "") %}
	{% if not nlu_msg in v %}
	SAVE_VARIABLE VARIABLE={variable} VALUE='"{nlu_msg} (was {v})"'
	{% endif %}
	CONSOLE_ECHO TITLE="Deprecated ratos-variables.cfg variable" TYPE="warning" MSG="The variable {variable} is no longer used, please remove it from your ratos-variables.cfg file."
	{% endif %}

[gcode_macro _NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK]
gcode = 
	
	
	
	
	
	
	
	{% set t = params.T|int %}
	{% set c = params.C|float %}
	{% set normal_low = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_low|default(0.05)|float %}
	{% set normal_high = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_high|default(0.10)|float %}
	
	{% if c < 0 %}
	
	{action_emergency_stop("Invalid nozzle_expansion_coefficient_t%s value in ratos-variables.cfg: %.3f. It must be non-negative." % (t, c))}
	{% endif %}
	{% if c >= normal_high %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite high. Please verify that this is correct."
	{% endif %}
	{% if c <= normal_low %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite low. Please verify that this is correct."
	{% endif %}

[gcode_macro INITIAL_FRONTEND_UPDATE]
gcode = 
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_error = printer["gcode_macro RatOS"].status_color_error|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_unknown}"'
	{% endif %}
	
	
	{% set t0_sensor = "undefined" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	{% set t0_sensor = "detected" %}
	{% else %}
	{% set t0_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t0_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	{% set t1_sensor = "undefined" %}
	{% if printer["dual_carriage"] is defined and printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	{% set t1_sensor = "detected" %}
	{% else %}
	{% set t1_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t1_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	{% if svv.t0_filament is defined and printer["gcode_macro T0"] is defined %}
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	{% if t0_sensor != "empty" %}
	{% set t0_filament_type = svv.t0_filament[0]|default('')|string %}
	{% set t0_filament_name = svv.t0_filament[1]|default('')|string %}
	{% set t0_filament_temp = svv.t0_filament[2]|default(0)|float %}
	{% if t0_filament_name != '' and t0_filament_type != '' and t0_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{t0_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{t0_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={t0_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}
	{% if svv.t1_filament is defined and printer["gcode_macro T1"] is defined %}
	{% if printer["gcode_macro T1"].filament_name is defined and printer["gcode_macro T1"].filament_type is defined and printer["gcode_macro T1"].filament_temp is defined %}
	{% if t1_sensor != "empty" %}
	{% set t1_filament_type = svv.t1_filament[0]|default('')|string %}
	{% set t1_filament_name = svv.t1_filament[1]|default('')|string %}
	{% set t1_filament_temp = svv.t1_filament[2]|default(0)|float %}
	{% if t1_filament_name != '' and t1_filament_type != '' and t1_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='"{t1_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='"{t1_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE={t1_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t1_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro CALCULATE_PRINTABLE_AREA]
variable_calculated = False
gcode = 
	{% if not calculated %}
	{% set bed_margin_x = printer["gcode_macro RatOS"].bed_margin_x %}
	{% set bed_margin_y = printer["gcode_macro RatOS"].bed_margin_y %}
	
	
	
	{% set tool = 0 if printer["gcode_macro T0"] is not defined or printer["gcode_macro T0"].active else 1 %}
	{% set max_x = printer.toolhead.axis_maximum.x if printer["dual_carriage"] is defined and tool == 0 else printer.toolhead.axis_maximum.x - bed_margin_x[1] %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	
	
	{% set max_x = printer.toolhead.axis_maximum.x %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="printer.toolhead.axis_maximum.x {printer.toolhead.axis_maximum.x}"
	
	{% set max_y = printer.toolhead.axis_maximum.y - bed_margin_y[1]%}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_x_max VALUE={max_x}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_y_max VALUE={max_y}
	SET_GCODE_VARIABLE MACRO=CALCULATE_PRINTABLE_AREA VARIABLE=calculated VALUE=True
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	RATOS_LOG PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	{% endif %}

[gcode_macro CACHE_TOOLHEAD_SETTINGS]
variable_cache = {"global": {"accel": 1000, "ratio": 0.5, "speed": 50, "scv": 5}}
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set dummy = cache.__setitem__(key, {"accel": printer.toolhead.max_accel, "ratio": printer.toolhead.minimum_cruise_ratio, "speed": printer.toolhead.max_velocity, "scv": printer.toolhead.square_corner_velocity}) %}
	SET_GCODE_VARIABLE MACRO=CACHE_TOOLHEAD_SETTINGS VARIABLE=cache VALUE="{cache | pprint | replace("\n", "") | replace("\"", "\\\"")}"
	DEBUG_ECHO PREFIX="CACHE_TOOLHEAD_SETTINGS" MSG="Toolhead settings cached for {key}. {printer.toolhead.max_accel} accel, {printer.toolhead.minimum_cruise_ratio} ratio, {printer.toolhead.max_velocity} velocity, {printer.toolhead.square_corner_velocity} scv."

[gcode_macro RESTORE_TOOLHEAD_SETTINGS]
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set values = printer["gcode_macro CACHE_TOOLHEAD_SETTINGS"].cache.__getitem__(key) %}
	{% if values is not defined or values == 'None' %}
	{ action_raise_error("RESTORE_TOOLHEAD_SETTINGS: Toolhead settings not cached for key '" ~ key ~ "'.") }
	{% endif %}
	SET_VELOCITY_LIMIT ACCEL={values.accel} MINIMUM_CRUISE_RATIO={values.ratio} VELOCITY={values.speed} SQUARE_CORNER_VELOCITY={values.scv}
	DEBUG_ECHO PREFIX="RESTORE_TOOLHEAD_SETTINGS" MSG="Toolhead settings restored. {values.accel} accel, {values.ratio} ratio, {values.speed} velocity, {values.scv} scv."

[gcode_macro SET_MACRO_TRAVEL_SETTINGS]
gcode = 
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float %}
	{% set accel = printer["gcode_macro RatOS"].macro_travel_accel %}
	SET_VELOCITY_LIMIT ACCEL={accel} MINIMUM_CRUISE_RATIO=0.5 VELOCITY={speed} SQUARE_CORNER_VELOCITY={5}
	DEBUG_ECHO PREFIX="SET_MACRO_TRAVEL_SETTINGS" MSG="Macro travel settings set. {accel} accel, {speed} velocity"

[gcode_macro SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% if printer["dual_carriage"] is not defined %}
	
	SET_KINEMATIC_POSITION X={printable_x_max / 2} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	{% else %}
	
	IDEX_SET_CENTER_KINEMATIC_POSITION
	{% endif %}

[gcode_macro IDEX_SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x - (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x + (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY

[gcode_macro VERIFY_HYBRID_INVERTED]
gcode = 
	
	{% set inverted = False %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy is defined and printer.fastconfig.settings.ratos_hybrid_corexy.inverted is defined %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy.inverted|lower == 'true' %}
	{% set inverted = True %}
	{% endif %}
	{% endif %}
	{% if inverted == False %}
	{ action_emergency_stop("ratos_hybrid_corexy NOT INVERTED! Inverted hybrid core-xy bugfix not detected.") }
	{% endif %}

[gcode_macro RATOS_ECHO]
gcode = 
	{% set prefix = "RatOS" %}
	{% set debug = params.DEBUG|default(0)|int %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " | " ~ params.PREFIX %}
	{% endif %}
	{% set prefix = prefix ~ ":" %}
	{% set msg = "" %}
	{% if params.MSG is defined %}
	{% set msg = params.MSG %}
	{% else %}
	{% set msg = "No msg parameter provided (this is a bug or unintended use)." %}
	{% endif %}
	{% if not debug %}
	
	M117 {prefix} {msg}
	{% endif %}
	RATOS_LOG PREFIX="{prefix}" MSG="{msg}"
	{% if not debug %}
	RESPOND PREFIX="{prefix}" MSG="{msg}"
	{% else %}
	CONSOLE_ECHO TITLE="{prefix}" TYPE="debug" MSG="{msg}"
	{% endif %}

[gcode_macro ENABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=True
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=prefix_filter VALUE="'{params.FILTER|default('')|lower}'"
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging enabled."

[gcode_macro DISABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=False
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging disabled."

[gcode_macro DEBUG_ECHO]
variable_enabled = False
variable_prefix_filter = ''
gcode = 
	{% set prefix = "DEBUG" %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " - " ~ params.PREFIX %}
	{% endif %}
	{% if enabled and (prefix_filter|lower == '' or prefix_filter|lower in params.PREFIX|lower) %}
	RATOS_ECHO PREFIX="{prefix}" MSG="{params.MSG}" DEBUG=1
	{% endif %}

[gcode_macro START_FEATURE]
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="Start {params.FEATURE} feature gcode"
	{% set scv = printer.toolhead.square_corner_velocity|int|default(5) %}
	{% set accel = printer.toolhead.max_accel|int|default(10000) %}
	{% set ratio = printer.toolhead.minimum_cruise_ratio|float|default(0.5) %}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="scv" VALUE={scv}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="accel" VALUE={accel}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="ratio" VALUE={ratio}
	_USER_START_FEATURE FEATURE="{params.FEATURE}"

[gcode_macro END_FEATURE]
variable_scv = 5
variable_accel = 10000
variable_ratio = 0.5
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="End {params.FEATURE} feature gcode"
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={scv} ACCEL={accel} MINIMUM_CRUISE_RATIO={ratio}
	_USER_END_FEATURE FEATURE="{params.FEATURE}" SCV={scv} ACCEL={accel} RATIO={ratio}

[gcode_macro _ON_LAYER_CHANGE]
variable_layer_number = 0
description = INTERNAL USE ONLY. Call it from the slicers after layer change custom gcode
gcode = 
	
	{% set layer = params.LAYER|int %}
	
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE={layer}
	SET_PRINT_STATS_INFO CURRENT_LAYER={layer}

[gcode_macro _LEARN_MORE_CALIBRATION]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/calibration" %}
	{% set link_text = "RatOS Calibration Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_CHAMBER_FILTER]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter Control" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_FILAMENT]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/filaments" %}
	{% set link_text = "RatOS Filament Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _CONSOLE_SAVE_CONFIG]
gcode = 
	M118 Click <a class="command text--blue">SAVE_CONFIG</a> to save the settings to your printer.cfg.

[gcode_macro _LOAD_RATOS_SKEW_PROFILE]
gcode = 
	{% set ratos_skew_profile = printer["gcode_macro RatOS"].skew_profile|default("") %}
	{% if ratos_skew_profile != "" %}
	{% if printer.fastconfig.config["skew_correction %s" % ratos_skew_profile] is defined %}
	SKEW_PROFILE LOAD={ratos_skew_profile}
	GET_CURRENT_SKEW
	{% else %}
	{% set line_1 = '"Could not find skew profile %s!_N_Clearing skew correction."' % ratos_skew_profile %}
	CONSOLE_ECHO TITLE="Missing skew profile!" TYPE="warning" MSG={line_1}
	SET_SKEW CLEAR=1
	{% endif %}
	{% endif %}

[gcode_macro M601]
gcode = 
	PAUSE

[gcode_macro _STOP_AND_RAISE_ERROR]
gcode = 
	M84
	_RAISE_ERROR MSG="{params.MSG}"

[gcode_macro _RESET_GCODE_VARIABLES]
description = Reset specified [gcode_macro ...] variables to their original values from configuration when Klipper started.
	- MACRO: Name of the GCODE macro containing the variables to reset.
	- VARIABLES: Comma-separated list of variable names to reset (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- QUIET: (optional) If true, suppresses console echo messages for each reset variable. Default is false.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set quiet = params.QUIET|default("false")|lower in ("true", "1", "yes") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	{% set settings = printer.fastconfig.settings[obj_name|lower] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro %s]" % macro) }
	{% endif %}
	
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if settings["variable_%s" % var] is not defined %}
	{ action_raise_error("Variable '%s' is not defined in settings for [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	
	{% for var in vars %}
	{% set var_value = obj[var] %}
	{% if var_value is defined %}
	{% set v = settings["variable_%s" % var] %}
	{% if v != var_value|string %}
	{% if var_value is string %}
	{% set v = '"\'' ~ v|replace('"', '\\"')|replace("'", "\\'") ~ '\'"' %}
	{% endif %}
	SET_GCODE_VARIABLE MACRO={macro} VARIABLE={var} VALUE={v}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Reset {macro} variable {var} to original value: {v} (was {obj[var]})"
	{% endif %}
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro _SHOW_GCODE_VARIABLES]
description = Show current values of specified [gcode_macro ...] variables.
	- MACRO: Name of the GCODE macro containing the variables to show.
	- VARIABLES: Comma-separated list of variable names to show (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- PAD: (optional) If defined, provide a single character to use for padding variable names to align values in a tabular format in the console output. Default is no padding.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set pad = params.PAD|default("") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	
	{% set ns = namespace() %}
	{% set ns.max_len = 0 %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% set ns.max_len = (ns.max_len, var|length)|max %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if pad %}
	{% set padding = pad * (ns.max_len - var|length) %}
	CONSOLE_ECHO MSG="{var}{padding} {obj[var]}"
	{% else %}
	CONSOLE_ECHO MSG="{var}: {obj[var]}"
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro PAUSE]
description = Pauses the print
rename_existing = PAUSE_BASE
variable_extrude = 1.5
variable_retract = 1.5
variable_fan_speed = 0
variable_idex_mode = ""
variable_idex_toolhead = 0
variable_idex_toolhead_x = 0.0
variable_idex_toolhead_y = 0.0
variable_idex_toolhead_z = 0.0
gcode = 
	RATOS_ECHO MSG="Pausing print..."
	
	
	{% set runout_detected = true if params.RUNOUT|default(false)|lower == 'true' else false %}
	
	
	_LED_PAUSE
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	SAVE_GCODE_STATE NAME=PAUSE_state
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_mode VALUE='"{idex_mode}"'
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={idex_toolhead}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_x VALUE={printer.gcode_move.gcode_position.x|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_y VALUE={printer.gcode_move.gcode_position.y|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_z VALUE={printer.gcode_move.gcode_position.z|float}
	DEBUG_ECHO PREFIX="PAUSE" MSG="idex_mode: {idex_mode}, idex_toolhead: {idex_toolhead}, idex_toolhead_x: {idex_toolhead_x}, idex_toolhead_y: {idex_toolhead_y}, idex_toolhead_z: {idex_toolhead_z}"
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="pause"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if current_z < (max_z - 20.0) %}
	{% set z_safe = 20.0 %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	PAUSE_BASE
	
	
	{% if printer["dual_carriage"] is not defined %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan"].speed|float}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	{% if idex_toolhead == 0 %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t1"].speed|float}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106 S0
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set R = printer["gcode_macro PAUSE"].retract|float %}
	{% if can_extrude %}
	G91
	G1 E-{R} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	{% set pause_print_park_x = printer["gcode_macro RatOS"].pause_print_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].pause_print_park_in %}
	{% if runout_detected %}
	{% set pause_print_park_x = printer["gcode_macro RatOS"].runout_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].runout_park_in %}
	{% endif %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	DEBUG_ECHO PREFIX="PAUSE" MSG="z_speed: {z_speed}, pause_print_park_x: {pause_print_park_x}, pause_print_park_in: {pause_print_park_in}, default_toolhead: {default_toolhead}"
	{% if "xyz" in printer.toolhead.homed_axes %}
	G91
	G1 Z{z_safe} F{z_speed}
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% else %}
	
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	_IDEX_SINGLE X={parking_position}
	{% else %}
	PARK_TOOLHEAD
	{% endif %}
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="pause"
	
	RATOS_ECHO MSG="Print paused"

[gcode_macro RESUME]
description = Resumes the print if the printer is paused.
rename_existing = RESUME_BASE
gcode = 
	
	
	RATOS_ECHO MSG="Resuming print..."
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	
	{% set target_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set target_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if target_idex_mode != '' %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set fan_speed = printer["gcode_macro PAUSE"].fan_speed|float %}
	{% if printer["dual_carriage"] is not defined %}
	M106 S{(fan_speed * 255)}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% else %}
	{% if params.TOOLHEAD is defined %}
	
	{% if params.TOOLHEAD == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% else %}
	{% if printer["gcode_macro PAUSE"].idex_toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	{% if params.TOOLHEAD is defined %}
	_SELECT_TOOL T={params.TOOLHEAD} X=-1 Y=-1 TOOLSHIFT=false
	{% else %}
	_SELECT_TOOL T={printer["gcode_macro PAUSE"].idex_toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	{% endif %}
	
	{% set x = printer["gcode_macro PAUSE"].idex_toolhead_x|float %}
	{% set y = printer["gcode_macro PAUSE"].idex_toolhead_y|float %}
	{% set z = printer["gcode_macro PAUSE"].idex_toolhead_z|float %}
	G1 X{x} Y{y} Z{z} F{speed}
	{% if params.TOOLHEAD is defined %}
	
	SAVE_GCODE_STATE NAME=PAUSE_STATE
	{% endif %}
	{% endif %}
	
	
	{% if params.TOOLHEAD is not defined %}
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% if can_extrude %}
	G91
	G1 E{E} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1 MOVE_SPEED={speed}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	RESUME_BASE
	
	
	_LED_PRINTING
	
	RATOS_ECHO MSG="Print resumed"

[gcode_macro CANCEL_PRINT]
description = Cancels the print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	RATOS_ECHO MSG="Cancelling print..."
	END_PRINT
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	
	CANCEL_PRINT_BASE
	RATOS_ECHO MSG="Print cancelled"

[gcode_macro START_PRINT]
description = Start print procedure, use this in your Slicer.
variable_post_processor_version = 2
variable_is_printing_gcode = False
variable_both_toolheads = True
variable_object_xoffset = 0
variable_first_x = -1
variable_first_y = -1
variable_total_toolshifts = 0
variable_initial_tool = 0
variable_extruder_first_layer_temp = ""
variable_extruder_other_layer_temp = ""
gcode = 
	
	{% if params.EXTRUDER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_TEMP parameter not found.")}
	{% endif %}
	{% if params.EXTRUDER_OTHER_LAYER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_OTHER_LAYER_TEMP parameter not found.")}
	{% endif %}
	{% if params.BED_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. BED_TEMP parameter not found.")}
	{% endif %}
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' and printer["gcode_macro RatOS"].danger_force_allow_auto_center_subject|default(false)|lower != 'true'%}
	
	
	
	
	
	{ action_raise_error("The experimental auto_center_subject feature is not supported in this version of RatOS. Please disable it in the RatOS macro settings.") }
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes and printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% if printer["gcode_macro _VAOC"].is_started|default(true)|lower == 'true' %}
	_VAOC_END
	{% endif %}
	{% endif %}
	
	
	_LED_START_PRINTING
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_USER_START_PRINT { rawparams }
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_probe_stowable = printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% endif %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	{% set X0 = params.X0|default(-1)|float %}
	{% set X1 = params.X1|default(-1)|float %}
	{% set Y0 = params.Y0|default(-1)|float %}
	{% set Y1 = params.Y1|default(-1)|float %}
	{% if first_x == -1 or first_y == -1 %}
	{% set first_x = params.FIRST_X|default(-1)|float %}
	{% set first_y = params.FIRST_Y|default(-1)|float %}
	{% endif %}
	{% set total_toolshifts = params.TOTAL_TOOLSHIFTS|default(0)|int %}
	{% set initial_tool = params.INITIAL_TOOL|default(default_toolhead)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	
	
	
	
	
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(printer.heater_bed.target, true)|float %}
	
	
	{% set total_layer_count = params.TOTAL_LAYER_COUNT|default(0)|int %}
	{% set extruder_first_layer_temp = (params.EXTRUDER_TEMP|default("")).split(",") %}
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL BEACON_CONTACT_START_PRINT_TRUE_ZERO={beacon_contact_start_print_true_zero} BEACON_CONTACT_CALIBRATE_MODEL_ON_TRUE_ZERO={beacon_contact_calibrate_model_on_true_zero}
	{% endif %}
	
	_START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH BED_TEMP={bed_temp}
	
	
	RATOS_ECHO MSG="First print coordinates X:{first_x} Y:{first_y}"
	
	
	{% if params.TOTAL_LAYER_COUNT is not defined %}
	{% set link_url = "https://os.ratrig.com/docs/slicers" %}
	{% set link_text = "RatOS Slicer Configuration" %}
	{% set line_1 = '"Your slicer gcode settings are not up to date._N_Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="Incomplete Slicer Configuration detected" TYPE="warning" MSG={line_1}
	{% endif %}
	
	
	SET_PRINT_STATS_INFO CURRENT_LAYER=1
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE=1
	{% if total_layer_count > 0 %}
	SET_PRINT_STATS_INFO TOTAL_LAYER={total_layer_count}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads %}
	{% set initial_tool = 0 if initial_tool == 1 else 1 %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	{% endif %}
	
	
	{% set both_toolheads = true %}
	{% if total_toolshifts == 0 %}
	{% set both_toolheads = false %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	{% endif %}
	{% if both_toolheads and (idex_mode == "copy" or idex_mode == "mirror") %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Gcode tool changes found. Copy and mirror mode do not support toolchanges.")}
	{% endif %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set both_toolheads = true %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=initial_tool VALUE={initial_tool}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_x VALUE={first_x}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_y VALUE={first_y}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=total_toolshifts VALUE={total_toolshifts}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=both_toolheads VALUE={both_toolheads}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_first_layer_temp VALUE="'{params.EXTRUDER_TEMP}'"
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_other_layer_temp VALUE="'{params.EXTRUDER_OTHER_LAYER_TEMP}'"
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE=0
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set svv = printer.save_variables.variables %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set stepper_x_position_min = printer.fastconfig.settings.stepper_x.position_min|float %}
	{% set stepper_x_position_endstop = printer.fastconfig.settings.stepper_x.position_endstop|float %}
	{% set dual_carriage_position_max = printer.fastconfig.settings.dual_carriage.position_max|float %}
	{% set dual_carriage_position_endstop = printer.fastconfig.settings.dual_carriage.position_endstop|float %}
	{% set x_parking_space = parking_position_t0 - (stepper_x_position_endstop , stepper_x_position_min)|max %}
	{% set dc_parking_space = (dual_carriage_position_endstop , dual_carriage_position_max)|min - parking_position_t1 %}
	{% if svv.idex_xoffset|abs >= (x_parking_space - 0.5) or svv.idex_xoffset|abs >= (dc_parking_space - 0.5) %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Toolhead x-offset is too high for the available parking space. Calibrate your X and DC endstop positions and make sure you stay below 1mm." % (copy_mode_max_width)) }
	{% endif %}
	{% endif %}
	
	
	{% if (idex_mode == "copy" or idex_mode == "mirror") and printer.fastconfig.settings.ratos.enable_gcode_transform %}
	
	{% if params.MIN_X is not defined or params.MAX_X is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Something went wrong! Missing important post processor start print parameter!") }
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE=0
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	
	{% set boundary_box_min_x = params.MIN_X|default(0)|float %}
	{% set boundary_box_max_x = params.MAX_X|default(printable_x_max)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if default_toolhead == 0 %}
	
	{% set boundary_box_max_x = boundary_box_max_x + svv.idex_xoffset %}
	{% else %}
	
	{% set boundary_box_min_x = boundary_box_min_x - svv.idex_xoffset %}
	{% endif %}
	
	{% set center_x = printable_x_max / 2.0 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set object_width = boundary_box_max_x - boundary_box_min_x %}
	{% set copy_mode_max_width = center_x %}
	{% set mirror_mode_max_width = center_x - safe_distance / 2.0 %}
	
	DEBUG_ECHO PREFIX="START_PRINT" MSG="OBJECT_WIDTH: {object_width} BOUNDARY_BOX_MIN_X: {boundary_box_min_x} BOUNDARY_BOX_MAX_X: {boundary_box_max_x} CENTER_X: {center_x} SAFE_DISTANCE: {safe_distance}"
	
	
	{% if idex_mode == "copy" and object_width > copy_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for copy mode! Max supported width is %s mm" % (copy_mode_max_width)) }
	{% endif %}
	{% if idex_mode == "mirror" and object_width > mirror_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for mirror mode! Max supported width is %s mm" % (mirror_mode_max_width)) }
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = (printable_x_max - boundary_box_max_x - boundary_box_min_x) / 2 %}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE={object_xoffset}
	{% endif %}
	
	{% endif %}
	
	
	{% set has_initial_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_toolhead_filament_sensor %}
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% set has_initial_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_bowden_filament_sensor %}
	
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% if printer["dual_carriage"] is defined and both_toolheads %}
	
	{% set has_secondary_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set has_secondary_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_CHAMBER_FILTER_ON AT="before_print_start"
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true' %}
	{% if both_toolheads %}
	RATOS_ECHO MSG="Spool join is not possible if both toolheads are in use!"
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	{% endif %}
	
	
	CLEAR_PAUSE
	{% if printer["gcode_macro RatOS"].force_absolute_position|lower == 'true' %}
	G90
	{% endif %}
	SAVE_GCODE_STATE NAME=start_print_state
	
	
	G21
	
	G90
	
	M82
	_USER_START_PRINT_BEFORE_HOMING { rawparams }
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_BEGIN_BATCH
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_Z_HOP
	
	
	{% if idex_mode != '' and not (printer.fastconfig.settings.beacon is defined and (beacon_contact_start_print_true_zero or beacon_adaptive_heat_soak)) %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	{% if chamber_temp > 0 %}
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED={printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float}
	{% endif %}
	{% endif %}
	_CHAMBER_HEATER_ON START_CHAMBER_TEMP={start_chamber_temp} CHAMBER_TEMP={chamber_temp}
	_USER_START_PRINT_HEAT_CHAMBER { rawparams } CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_START_PRINT_BEFORE_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	RATOS_ECHO MSG="Heating bed..."
	
	M190 S{bed_temp}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_adaptive_heat_soak %}
	_MOVE_TO_SAFE_Z_HOME
	
	G1 Z2.5 F{z_speed}
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK LAYER_QUALITY={beacon_adaptive_heat_soak_layer_quality} MAXIMUM_FIRST_LAYER_DURATION={beacon_adaptive_heat_soak_maximum_first_layer_duration} MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={beacon_adaptive_heat_soak_max_wait}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_BED { rawparams }
	
	
	_START_PRINT_AFTER_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	_USER_START_PRINT_BED_MESH { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_BED_MESH X0={X0} X1={X1} Y0={Y0} Y1={Y1} T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_END_BATCH
	{% endif %}
	
	
	{% if idex_mode == '' %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[initial_tool]|float}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[0]|float}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={extruder_first_layer_temp[1]|float}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_PARK { rawparams }
	
	
	_START_PRINT_PARK
	
	
	RATOS_ECHO MSG="Heating Extruder..."
	{% if idex_mode == '' %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[initial_tool]|float}  MAXIMUM={extruder_first_layer_temp[initial_tool]|float + 5}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[0]|float}  MAXIMUM={extruder_first_layer_temp[0]|float + 5}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder1" MINIMUM={extruder_first_layer_temp[1]|float}  MAXIMUM={extruder_first_layer_temp[1]|float + 5}
	{% endif %}
	{% endif %}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	{% if idex_mode == '' %}
	_LED_PRINTING
	{% else %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	_LED_PRINTING
	{% else %}
	{% if both_toolheads %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	{% if toolchange_standby_temp > -1 %}
	_LED_TOOLHEAD_STANDBY TOOLHEAD={0 if initial_tool == 1 else 1}
	{% else %}
	_LED_PRINTING TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% else %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_EXTRUDER { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_AFTER_HEATING_EXTRUDER X0={X0} X1={X1} Y0={Y0} Y1={Y1} INITIAL_TOOLHEAD={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if idex_mode != '' %}
	{% if not both_toolheads %}
	{% if initial_tool != default_toolhead %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if idex_mode != '' %}
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=standby VALUE=False
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=standby VALUE=False
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if initial_tool == 1 else 'extruder1'} TARGET={toolchange_standby_temp}
	SET_GCODE_VARIABLE MACRO=T{0 if initial_tool == 1 else 1} VARIABLE=standby VALUE=True
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=start_print_state
	
	{% if printer["dual_carriage"] is defined %}
	_SET_IDEX_MODE_OFFSET
	{% endif %}
	
	
	{% if idex_mode != '' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% if idex_mode == "copy" and idex_mode != act_idex_mode %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == "mirror" and idex_mode != act_idex_mode %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={object_xoffset} MOVE=0
	{% endif %}
	{% else %}
	_SELECT_TOOL T={initial_tool} TOOLSHIFT=false
	_SET_TOOLHEAD_OFFSET
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	_SET_EXTRUSION_MODE
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={printer["print_stats"].print_duration}
	{% endif %}
	
	
	_USER_END_START_PRINT { rawparams }
	
	G92 E0
	
	
	_CHAMBER_FILTER_ON AT="after_print_start"
	
	_ALERT_NON_ZERO_Z_OFFSET
	
	RATOS_ECHO MSG="Printing..."

[gcode_macro _START_PRINT_BEFORE_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set is_stowable_probe = true if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' else false %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Pre-heating extruder..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={min_temp}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET={min_temp}
	{% endif %}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	{% endif %}
	{% endif %}
	
	
	{% if not is_stowable_probe %}
	{% if printer["dual_carriage"] is defined and act_t != default_toolhead %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	{% endif %}
	RATOS_ECHO MSG="Heat soaking z probe..."
	_MOVE_TO_SAFE_Z_HOME
	
	G0 Z2 F{z_speed}
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Waiting for extruder to be preheated..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	{% if default_toolhead == 0 %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_Z_HOP
	{% endif %}
	
	
	{% if auto_z_offset_calibration %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	PARK_TOOLHEAD
	_CLEANING_MOVE TOOLHEAD={default_toolhead} AUTOMATED=True
	_SELECT_TOOL T={0 if default_toolhead == 1 else 1} X={parking_position_t0 if default_toolhead == 1 else parking_position_t1} Y=0 TOOLSHIFT=false
	_CLEANING_MOVE TOOLHEAD={0 if default_toolhead == 1 else 1} AUTOMATED=True
	_VAOC_CALIBRATE_Z_OFFSET AUTO_Z_OFFSET=True
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=false
	{% endif %}
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	{% if needs_rehoming %}
	G28 Z
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	_START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE
	{% endif %}
	{% endif %}
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	PROBE PROBE_METHOD=contact SAMPLES=1

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	{% set fuzzy_radius = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_radius|default(0)|float if beacon_contact_start_print_true_zero_fuzzy_position else 0 %}
	
	{% set contact_true_zero_temp_has_been_set = False %}
	
	
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	
	
	
	{% if printer.beacon.last_probe_result|lower == "ok" %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	RATOS_ECHO MSG="Auto calibration nozzle wipe with probe result {last_z_offset}..."
	G0 Z{(0.2 + last_z_offset)} F{z_speed}
	G0 X70 F300
	{% else %}
	RATOS_ECHO MSG="Skipping auto calibration nozzle wipe because probing failed!"
	{% endif %}
	{% elif beacon_contact_wipe_before_true_zero_method == "probe_clean" %}
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	
	{% set contact_true_zero_temp_has_been_set = True %}
	
	
	
	
	
	
	
	
	BEACON_PROBE_CLEAN X=50 Y=10
	{% else %}
	CONSOLE_ECHO TYPE="error" TITLE="Unknown wipe method" MSG="Unknown wipe method '{beacon_contact_wipe_before_true_zero_method}' configured, skipping wipe before beacon true zero."
	{% endif %}
	{% endif %}
	
	
	G0 Z5 F{z_speed}
	_MOVE_TO_SAFE_Z_HOME FUZZY_RADIUS={fuzzy_radius}
	
	
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION
	
	{% if not contact_true_zero_temp_has_been_set %}
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon contact auto calibration..."
	
	{% if beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	
	G0 Z5 F{z_speed}

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION]
gcode = 
	{% set pos = printer.ratos.last_move_to_safe_z_home_position %}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE={pos[0]}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE={pos[1]}

[gcode_macro _START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set first_x = printer["gcode_macro START_PRINT"].first_x|default(-1)|float %}
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2.0 %}
	{% set center_y = printable_y_max / 2.0 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% if printer["dual_carriage"] is defined %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% endif %}
	
	
	{% set X0 = params.X0|default(-1)|int %}
	{% set X1 = params.X1|default(-1)|int %}
	{% set Y0 = params.Y0|default(-1)|int %}
	{% set Y1 = params.Y1|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	
	{% if idex_mode == '' %}
	
	_PRIME
	{% else %}
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	RATOS_ECHO PREFIX="IDEX" MSG="using combined prime offset for IDEX {idex_mode} mode"
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	{% if both_toolheads %}
	{% if initial_toolhead == 0 %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T{initial_toolhead}"
	_SELECT_TOOL T={initial_toolhead} TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	SET_MACRO_TRAVEL_SETTINGS
	
	{% if (X0 > -1 and Y1 > -1) or (first_x > 0 and first_y > 0) %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	{% endif %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	{% set first_z = 1 %}
	{% else %}
	{% set first_z = 3 %}
	{% endif %}
	
	
	{% if idex_mode == "mirror" %}
	{% if first_y >= 0 %}
	G0 Y{first_y} F{speed}
	{% else %}
	G0 Y{Y1} F{speed}
	{% endif %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={initial_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={initial_toolhead} E={printer["gcode_macro RatOS"].toolchange_first_purge|default(50)|float}
	_CLEANING_MOVE TOOLHEAD={initial_toolhead} AUTOMATED=True
	{% endif %}
	{% if first_x >= 0 and first_y >= 0 %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% else %}
	{% set first_x = X0 %}
	{% set first_y = Y0 %}
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'min' %}
	{% set first_x = X0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'max' %}
	{% set first_x = X1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|float <= center_x %}
	{% set first_x = X0 %}
	{% else %}
	{% set first_x = X1 %}
	{% endif %}
	{% endif %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'min' %}
	{% set first_y = Y0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'max' %}
	{% set first_y = Y1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|float <= center_y %}
	{% set first_y = Y0 %}
	{% else %}
	{% set first_y = Y1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	
	
	_LOAD_RATOS_SKEW_PROFILE

[gcode_macro _PRIME]
gcode = 
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	PRIME_BLOB INITIAL_TOOLHEAD={params.INITIAL_TOOLHEAD} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={params.IDEX_MODE} Y1={params.Y1}
	{% else %}
	
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif params.IDEX_MODE == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro END_PRINT]
description = End print procedure, use this in your Slicer.
gcode = 
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SAVE_GCODE_STATE NAME=end_print_state
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = printer["gcode_macro START_PRINT"].object_xoffset|default(0)|float %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(0-object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={(0-object_xoffset)}
	{% endif %}
	{% endif %}
	
	
	_USER_END_PRINT_BEFORE_HEATERS_OFF { rawparams }
	_END_PRINT_BEFORE_HEATERS_OFF
	TURN_OFF_HEATERS
	_USER_END_PRINT_AFTER_HEATERS_OFF { rawparams }
	_END_PRINT_AFTER_HEATERS_OFF
	_USER_END_PRINT_PARK { rawparams }
	_END_PRINT_PARK
	
	
	{% if printer["gcode_macro RatOS"].skew_profile is defined %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined and printer["gcode_macro RatOS"].end_print_motors_off|lower != 'false' %}
	
	M84
	{% endif %}
	
	
	M107
	
	
	BED_MESH_CLEAR
	RATOS_ECHO MSG="Done :)"
	
	
	RESTORE_GCODE_STATE NAME=end_print_state
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	M84
	{% endif %}
	
	
	RESET_NAMED_OFFSET EVENT="end_print"
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_CHAMBER_FILTER_ON AT="print_end"
	_CHAMBER_FILTER_OFF
	
	
	_CHAMBER_HEATER_OFF
	
	_USER_END_PRINT_FINISHED { rawparams }

[gcode_macro _END_PRINT_BEFORE_HEATERS_OFF]
gcode = 
	RATOS_ECHO MSG="Cleaning up..."

[gcode_macro _END_PRINT_AFTER_HEATERS_OFF]
gcode = 
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% set z_hop = printer["gcode_macro RatOS"].end_print_park_z_hop|float %}
	{% set r = printer["gcode_macro RatOS"].end_print_retract_filament|default(4)|float %}
	{% if current_z < (max_z - z_hop) %}
	{% set z_safe = z_hop %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G91
	
	{% if can_extrude %}
	G1 E-2 F3600
	{% endif %}
	
	G0 Z{z_safe} F3600
	
	{% if can_extrude %}
	G1 E-{(r-2)} F3600
	{% endif %}
	
	G90

[gcode_macro _SET_EXTRUSION_MODE]
gcode = 
	
	{% if printer["gcode_macro RatOS"].relative_extrusion|lower == 'true' %}
	M83
	{% else %}
	M82
	{% endif %}

[gcode_macro GENERATE_SHAPER_GRAPHS]
description = Genarates input shaper resonances graphs for analysis. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	{% set hz_per_sec = params.HZ_PER_SEC|default(1)|float %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set copy_mode_offset = printable_x_max / 4.0 %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	_IDEX_SINGLE
	{% endif %}
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	
	
	{% if idex_mode != 'copy' and idex_mode != 'mirror' %}
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	{% endif %}
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Shaper graph"

[gcode_shell_command generate_shaper_graph_x]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-x.sh
timeout = 60.
verbose = True

[gcode_shell_command generate_shaper_graph_y]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-y.sh
timeout = 60.
verbose = True

[gcode_macro MEASURE_COREXY_BELT_TENSION]
description = Generates resonance graph used to ensure belts are equally tensioned. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	_IDEX_SINGLE
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if measure_t1 == false or measure_t0 == false %}
	{action_raise_error("Axis specified. Not supported for belt tension on Y.")}
	{% else %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	G4 P5000
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	PARK_TOOLHEAD
	{% endif %}
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	G1 X{parking_position_t1} F{speed}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	
	
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Belt Tension Graph"

[gcode_shell_command generate_belt_tension_graph]
command = /home/pi/printer_data/config/RatOS/scripts/generate-belt-tension-graph.sh
timeout = 90.
verbose = True

[idle_timeout]
gcode = 
	{% if printer.webhooks.state|lower == 'ready' %}
	{% if printer.pause_resume.is_paused|lower == 'false' %}
	_USER_BEFORE_IDLE_TIMEOUT
	RATOS_ECHO PREFIX="IDLE" MSG="2 hours since last activity. Powering off heaters and motors.."
	TURN_OFF_HEATERS
	M84
	_USER_AFTER_IDLE_TIMEOUT
	{% endif %}
	{% endif %}
timeout = 7200

[temperature_sensor raspberry_pi]
sensor_type = temperature_host

[skew_correction]

[named_offsets]

[input_shaper]

[virtual_sdcard]
path = ~/printer_data/gcodes

[display_status]

[pause_resume]

[force_move]
enable_force_move = True

[respond]

[resonance_generator]

[ratos]
allow_unknown_gcode_generator = True
enable_gcode_transform = True

[exclude_object]

[bed_mesh]
split_delta_z = 0.001
horizontal_move_z = 2
mesh_min = 20,20
mesh_max = 480,480
probe_count = 40,40
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = .2
speed = 600
log_points = False

[fastconfig]

[heater_bed]
heater_pin = heater_bed_heating_pin
sensor_pin = heater_bed_sensor_pin
sensor_type = Generic 3950
min_temp = 0
max_temp = 140
pwm_cycle_time = 0.103
control = pid
pid_kp = 61.987
pid_ki = 1.781
pid_kd = 539.289

[printer]
kinematics = ratos_hybrid_corexy
max_velocity = 800
max_accel = 10000
minimum_cruise_ratio = 0.5
max_z_velocity = 50
max_z_accel = 600
square_corner_velocity = 5

[ratos_hybrid_corexy]
inverted = true

[dual_carriage]
axis = x
safe_distance = 55
position_max = 559.6
position_endstop = 559.6
position_min = 0
step_pin = PF9
dir_pin = dual_carriage_dir_pin
enable_pin = !PG2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t1:PA2

[gcode_macro _SET_IDEX_MODE_OFFSET]
description = "Internal use only. Sets the 'idex_mode' named offset that the active idex mode requires."
gcode = 
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_SET_IDEX_MODE_OFFSET" MSG="idex_mode: {idex_mode}, center_x: {center_x}"
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	SET_NAMED_OFFSET NAME=idex_mode X={(-center_x / 2)}
	{% else %}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% else %}
	{action_raise_error("_SET_IDEX_MODE_OFFSET: Printer not homed")}
	{% endif %}

[gcode_macro IDEX_SINGLE]
gcode = 
	_IDEX_REMAP_TOOLHEADS ENABLE=False
	_IDEX_SINGLE

[gcode_macro _IDEX_SINGLE]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_single"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set init = params.INIT|default(0)|int %}
	{% set new_x = params.X|default(-1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_default_t = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="init: {init}, new_x: {new_x}, idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, act_t: {act_t}"
	
	{% if idex_mode == "copy" or idex_mode == "mirror" or init == 1 %}
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="reset idex_mode offset"
	G1 X{center_x} F{(speed)}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="activate default carriage"
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolheads"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	G90
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position."
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1}
	G1 X{parking_position_default_t} F{speed}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move default toolhead to its new position."
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% if new_x == -1 %}
	{% set new_x = center_x %}
	{% endif %}
	G1 X{new_x} F{speed}
	
	M400
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="X Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set extruder motion queue."
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if default_toolhead==0 else default_toolhead}
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolhead offset."
	_SET_TOOLHEAD_OFFSET
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set input shaper."
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[default_toolhead]|float)} SHAPER_FREQ_Y={(shaper_y_freq[default_toolhead]|float)} SHAPER_TYPE_X={(shaper_x_type[default_toolhead]|lower)} SHAPER_TYPE_Y={(shaper_y_type[default_toolhead]|lower)}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="update Frontend."
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if default_toolhead==0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if default_toolhead==1 else False}
	{% else %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_single"

[gcode_macro IDEX_COPY]
gcode = 
	_IDEX_COPY

[gcode_macro _IDEX_COPY]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_copy"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set y = params.Y|default(-1)|int %}
	{% set dance = params.DANCE|default(1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_COPY" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}, y: {y}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "copy" %}
	{% if idex_mode == "mirror" %}
	{% if y>=0 %}
	G1 X{center_x} Y{y} F{(speed)}
	{% else %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	
	
	{% if idex_mode != "mirror" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance == 1 %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[2]|float)} SHAPER_FREQ_Y={(shaper_y_freq[2]|float)} SHAPER_TYPE_X={(shaper_x_type[2]|lower)} SHAPER_TYPE_Y={(shaper_y_type[2]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_copy"

[gcode_macro IDEX_MIRROR]
gcode = 
	_IDEX_MIRROR

[gcode_macro _IDEX_MIRROR]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_mirror"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set dance = params.DANCE|default(1)|int %}
	{% set priming = params.PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_MIRROR" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "mirror" %}
	
	{% if idex_mode == "copy" %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS MIRROR_PRIMING={params.PRIMING}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=MIRROR
	
	
	{% if idex_mode != "copy" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance and not priming %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[3]|float)} SHAPER_FREQ_Y={(shaper_y_freq[3]|float)} SHAPER_TYPE_X={(shaper_x_type[3]|lower)} SHAPER_TYPE_Y={(shaper_y_type[3]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_mirror"

[gcode_macro _IDEX_SET_TOOLHEADS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set mirror_priming = params.MIRROR_PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position_inactive_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_IDEX_SET_TOOLHEADS" MSG="idex_mode: {idex_mode}, act_t: {act_t}, center_x: {center_x}, mirror_priming: {mirror_priming}"
	
	
	{% if act_t != default_toolhead %}
	_SET_TOOLHEAD_OFFSET FORCE_TOOLHEAD={default_toolhead} MOVE=1
	{% endif %}
	
	{% if mirror_priming %}
	
	
	
	{% if parking_position_t0|abs < parking_position_t1 - printable_x_max %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{printable_x_max + parking_position_t0|abs} F{(speed)}
	{% else %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{0 - (parking_position_t1 - printable_x_max)} F{(speed)}
	{% endif %}
	
	{% else %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1} MODE=PRIMARY
	G1 X{parking_position_inactive_t} F{(speed)}
	
	
	{% if act_t==1 %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{center_x / 2} F{(speed)}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"

[gcode_macro IDEX_PARK]
gcode = 
	
	PARK_TOOLHEAD

[gcode_macro PARK_TOOLHEAD]
gcode = 
	
	{% set idex_mode = 'none' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="PARK_TOOLHEAD" MSG="Parking T{act_t}.."
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set parking_position_inact_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set printable_y_min = printer["gcode_macro RatOS"].printable_y_min|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" and 'xy' in printer.toolhead.homed_axes %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% elif printer.toolhead.position.y|float < printable_y_min %}
	G1 Y{printable_y_min} F{speed}
	{% endif %}
	
	SAVE_GCODE_STATE NAME=_PARK_TOOLHEAD
	G90
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0.5
	
	
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_inact_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	
	SET_VELOCITY_LIMIT ACCEL={printer.toolhead.max_accel} MINIMUM_CRUISE_RATIO=0.5
	M400
	RESTORE_GCODE_STATE NAME=_PARK_TOOLHEAD
	
	{% endif %}

[gcode_macro JOIN_SPOOLS]
gcode = 
	
	{% set spools = params.SPOOLS|default("") %}
	
	{% if spools == "" %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% else %}
	{% if spools != "0,1" and spools != "1,0" %}
	RATOS_ECHO MSG="Wrong spool configuration!"
	RATOS_ECHO MSG="Join Spools = JOIN_SPOOLS SPOOLS=0,1"
	RATOS_ECHO MSG="Deactivate = JOIN_SPOOLS SPOOLS="
	{% else %}
	{% if spools == "0,1" or spools == "1,0" %}
	_IDEX_JOIN_SPOOLS ENABLE=true
	{% else %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_JOIN_SPOOLS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if enable %}
	{% set has_t0_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t1_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t0_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined else false %}
	{% set has_t1_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined else false %}
	{% if (has_t0_toolhead_filament_sensor and has_t1_toolhead_filament_sensor) or (has_t0_bowden_filament_sensor and has_t1_bowden_filament_sensor) %}
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=True
	RATOS_ECHO MSG="Spool joining enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Can not enable spool joining! No filament sensors found."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining deactivated!"
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining is not possible in copy and mirror mode!"
	{% endif %}

[gcode_macro _JOIN_SPOOL]
gcode = 
	
	{% set old_toolhead = params.TOOLHEAD|int %}
	{% set new_toolhead = 0 if old_toolhead == 1 else 1 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set purge_after_load = printer["gcode_macro T%s" % new_toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_JOIN_SPOOL" MSG="toolhead: {new_toolhead}"
	
	{% set has_filament = true %}
	{% set has_new_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% set has_new_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% if has_new_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	{% if has_new_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	
	{% if has_filament %}
	RATOS_ECHO MSG="Joining spools! Please wait for extruder to heat up...."
	
	
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={new_toolhead}
	
	
	_DEACTIVATE_TOOLHEAD TOOLHEAD={old_toolhead}
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set extruder_temp = extruder_first_layer_temp[new_toolhead]|float %}
	{% else %}
	{% set extruder_temp = extruder_other_layer_temp[new_toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if new_toolhead == 0 else 'extruder1'} TARGET={extruder_temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if new_toolhead == 0 else 'extruder1'} MINIMUM={extruder_temp}  MAXIMUM={extruder_temp + 5}
	
	
	{% if purge_after_load > 0 %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_toolhead == 0 else new_toolhead}
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={new_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={new_toolhead} E={purge_after_load}
	_CLEANING_MOVE TOOLHEAD={new_toolhead} AUTOMATED=True
	
	
	SET_DUAL_CARRIAGE CARRIAGE={old_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if old_toolhead == 0 else old_toolhead}
	
	{% endif %}
	
	
	RESUME TOOLHEAD={new_toolhead}
	
	
	_IDEX_JOIN_SPOOLS ENABLE=false
	
	{% else %}
	{ action_raise_error("Spool join failed! No filament found or filament sensor is disabled.") }
	{% endif %}

[gcode_macro REMAP_TOOLHEADS]
gcode = 
	
	{% set toolheads = params.TOOLHEADS|default("") %}
	
	{% if toolheads == "" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% else %}
	{% if toolheads != "0,1" and toolheads != "1,0" %}
	RATOS_ECHO MSG="Wrong toolhead configuration!"
	RATOS_ECHO MSG="Remap = REMAP_TOOLHEADS TOOLHEADS=0,1"
	RATOS_ECHO MSG="Deactivate = REMAP_TOOLHEADS TOOLHEADS="
	{% else %}
	{% if toolheads == "0,1" or toolheads == "1,0" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=true
	_IDEX_SINGLE
	{% else %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_REMAP_TOOLHEADS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	{% if not enable or (idex_mode != "copy" and idex_mode != "mirror") %}
	{% if enable %}
	RATOS_ECHO MSG="Toolhead remapping enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping deactivated!"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE={enable}
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping not possible in copy and mirror mode!"
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	{% endif %}

[gcode_macro SHAPER_CALIBRATE]
rename_existing = SHAPER_CALIBRATE_ORG
gcode = 
	RATOS_ECHO PREFIX="IDEX" MSG="SHAPER_CALIBRATE is useless on IDEX machines. Please use the GENERATE_SHAPER_GRAPHS macro and type the values into `variable_shaper_*_freq` and `variable_shaper_*_type manually`."

[gcode_shell_command generate_shaper_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-shaper-graph.sh
timeout = 120.
verbose = True

[gcode_shell_command generate_tension_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-belt-tension-graph.sh
timeout = 120.
verbose = True

[gcode_macro SET_PRESSURE_ADVANCE]
variable_snyc_toolheads = False
rename_existing = SET_PRESSURE_ADVANCE_BASE
gcode = 
	{% if params.SYNC_TOOLHEADS is defined %}
	{% set snyc_toolheads = true if params.SYNC_TOOLHEADS|default(false)|lower == 'true' else false %}
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=True
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="Syncing toolheads..."
	{% else %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' or snyc_toolheads %}
	{% set advance = params.ADVANCE|default(printer['extruder'].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['extruder'].smooth_time|float)|float %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T0"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T1"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder1' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% else %}
	{% set extruder = 'extruder' if act_t == 0 else 'extruder1' %}
	{% if params.EXTRUDER is defined %}
	{% set extruder = params.EXTRUDER %}
	{% endif %}
	{% if extruder == 'extruder' or extruder == 'extruder1' %}
	{% set advance = params.ADVANCE|default(printer['%s' % extruder].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['%s' % extruder].smooth_time|float)|float %}
	SET_PRESSURE_ADVANCE_BASE EXTRUDER={extruder} ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% if params.EXTRUDER is not defined %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG={"T%s" % act_t}
	{% endif %}
	{% else %}
	SET_PRESSURE_ADVANCE_BASE { rawparams }
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro M106]
rename_existing = M106.1
variable_swap_speed = -1
gcode = 
	
	{% set s = [[params.S|default(255)|int, 255]|min, 0]|max %}
	{% set p = params.P|default(-1)|int %}
	{% set speed = s / 255 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set t = 1 if idex_mode=='primary' else 0 %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(0)|int == 1 else false %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set sync_fans = true %}
	{% endif %}
	
	
	{% if sync_fans and idex_mode != "copy" and idex_mode != "mirror" %}
	
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int %}
	
	
	{% if toolshift_count > total_toolshifts %}
	{% set sync_fans = false %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE=-1
	
	
	{% if p == -1 %}
	
	{% if speed == 0 %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed}
	{% else %}
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE={speed}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={(speed if (t == 0 or sync_fans) else 0)}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={(speed if (t == 1 or sync_fans) else 0)}
	{% endif %}
	{% else %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed if t == p else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed if t == p else 0}
	{% endif %}
	
	
	M106.1 S{s}

[gcode_macro M107]
rename_existing = M107.1
gcode = 
	{% set p = params.P|default(-1)|int %}
	M106 S0 P{p}

[gcode_macro _SELECT_TOOL]
variable_last_timestamp = 0
gcode = 
	{% if params.T is defined %}
	{% set idex_mode = '' %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if "xyz" not in printer.toolhead.homed_axes and (idex_mode == "copy" or idex_mode == "mirror") %}
	_IDEX_SINGLE
	{% set idex_mode = 'reset' %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set new_t = params.T|int %}
	
	
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads and is_printing_gcode %}
	{% set new_t = 0 if new_t == 1 else 1 %}
	{% endif %}
	
	
	{% set toolchange_prepurging_timer = printer["gcode_macro RatOS"].toolchange_prepurging_timer|default(0)|int %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	DEBUG_ECHO PREFIX="_SELECT_TOOL" MSG="act_t: {act_t}, new_t: {new_t}, is_printing_gcode: {is_printing_gcode}, swap_toolheads: {swap_toolheads}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	{% set act_extruder = 'extruder%s' % ('' if new_t == 0 else new_t) %}
	{% if new_t != act_t or printer.toolhead.extruder != act_extruder or idex_mode == 'reset' %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Selecting T{new_t}.."
	
	
	M220 S100
	
	
	
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(1)|int == 1 else false %}
	
	
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set toolshift = false %}
	{% endif %}
	
	
	{% set fan_speed = printer["fan_generic part_fan_t%s" % act_t].speed %}
	
	
	{% set deactivate_toolhead = false %}
	{% if is_printing_gcode %}
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int + 1 %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE={toolshift_count}
	{% if toolshift_count == total_toolshifts %}
	{% set deactivate_toolhead = true %}
	{% endif %}
	{% endif %}
	
	
	{% set needs_wakeup = true if printer["gcode_macro T%s" % new_t].standby|default(false)|lower == 'true' else false %}
	
	
	{% set needs_purging = false %}
	{% set wake_up_purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% if is_printing_gcode and toolchange_prepurging_timer > 0 and wake_up_purge > 0 %}
	{% set new_timestamp = printer["print_stats"].print_duration %}
	{% set elapsed_time = new_timestamp - last_timestamp %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={new_timestamp}
	{% if elapsed_time > toolchange_prepurging_timer %}
	{% set needs_purging = true %}
	{% endif %}
	{% endif %}
	
	
	{% set first_use_purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% if toolshift_count == 1 and first_use_purge > 0 %}
	{% set needs_purging = true %}
	{% endif %}
	
	
	{% if is_printing_gcode and (toolchange_standby_temp > -1 or needs_purging or needs_wakeup) %}
	_TOOLHEAD_STANDBY TOOLHEAD={act_t}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	_TOOLHEAD_WAKEUP TOOLHEAD={new_t} X={new_x} Y={new_y} Z={new_z} FAN_SPEED={fan_speed} TOOLSHIFT_COUNT={toolshift_count}
	{% else %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(false)|lower == 'true' else false %}
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if (new_t == 0 or sync_fans) else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if (new_t == 1 or sync_fans) else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	_TOOLCHANGE T={new_t} X={new_x} Y={new_y} Z={new_z} PARK_T0={park_t0} PARK_T1={park_t1} TOOLSHIFT={toolshift}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[new_t]|float)} SHAPER_FREQ_Y={(shaper_y_freq[new_t]|float)} SHAPER_TYPE_X={(shaper_x_type[new_t]|lower)} SHAPER_TYPE_Y={(shaper_y_type[new_t]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if new_t == 0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if new_t == 1 else False}
	
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% set sanity_check_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if new_t == 0 %}
	{% if printer.toolhead.extruder == 'extruder' %}
	{% if sanity_check_idex_mode == 'primary' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% elif new_t == 1 %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% if sanity_check_idex_mode == 'inactive' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _TOOLHEAD_STANDBY]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Putting toolhead T{toolhead} into standby mode."
	DEBUG_ECHO PREFIX="_TOOLHEAD_STANDBY" MSG="toolhead: {toolhead}, config_z_hop: {config_z_hop}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={toolhead} SYNC=0
	PARK_TOOLHEAD
	
	
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={toolchange_standby_temp}
	{% endif %}
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=True
	{% endif %}
	
	
	_LED_TOOLHEAD_STANDBY TOOLHEAD={toolhead}

[gcode_macro _TOOLHEAD_WAKEUP]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set fan_speed = params.FAN_SPEED|float %}
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift_count = params.TOOLSHIFT_COUNT|default(0)|int %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% if toolshift_count == 1 %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% endif %}
	{% set needs_wakeup = true if printer["gcode_macro T%s" % toolhead].standby|default(false)|lower == 'true' else false %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Waking up toolhead T{toolhead}. Please wait for extruder to heat up..."
	DEBUG_ECHO PREFIX="_TOOLHEAD_WAKEUP" MSG="toolhead: {toolhead}, fan_speed: {fan_speed}, new_x: {new_x}, new_y: {new_y}, new_z: {new_z}, config_z_hop: {config_z_hop}"
	
	
	_LED_TOOLHEAD_WAKEUP TOOLHEAD={toolhead}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={toolhead} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE=1
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if toolhead == 0 else toolhead}
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if needs_wakeup %}
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set temp = extruder_first_layer_temp[toolhead]|float %}
	{% else %}
	{% set temp = extruder_other_layer_temp[toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if toolhead == 0 else 'extruder1'} MINIMUM={temp}  MAXIMUM={temp + 5}
	{% endif %}
	
	
	_LED_PRINTING TOOLHEAD={toolhead}
	
	
	{% if purge > 0 %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={toolhead} E={purge}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	
	
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if toolhead == 1 else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	G92 E0
	G1 E-{e} F{feedrate}
	G92 E0
	
	
	{% if new_x >= 0 and new_y >= 0 %}
	G1 X{new_x} Y{new_y} F{speed}
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={config_z_hop} T={toolhead} SYNC=0
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=False

[gcode_macro _TOOLCHANGE]
variable_toolshift_count = 0
gcode = 
	
	
	{% set new_t = params.T|default(-1)|int %}
	{% set new_x = params.X|default(-1.0)|float %}
	{% set new_y = params.Y|default(-1.0)|float %}
	{% set new_z = params.Z|default(-1.0)|float %}
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(true)|lower == 'true' else false %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T: {new_t}, X: {new_x}, Y: {new_y}, Z: {new_z}, PARK_T0: {park_t0}, PARK_T1: {park_t1}, IS_PRINTING_GCODE: {is_printing_gcode}, TOOLSHIFT: {toolshift}"
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	{% if park_t0 >= 0 and park_t1 >= 0 %}
	{% set parking_position_t0 = park_t0 %}
	{% set parking_position_t1 = park_t1 %}
	{% set parking_position_act_t = park_t0 if act_t == 0 else park_t1 %}
	{% endif %}
	
	
	{% if not is_printing_gcode and not toolshift %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Changing tool to T{new_t} without retracting/extruding or moving the toolheads except for parking."
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	G90
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% if not is_printing_gcode and toolshift and new_x < 0 and new_y < 0 %}
	{% set new_x = center_x %}
	{% set new_y = printer.gcode_move.gcode_position.y|float %}
	{% endif %}
	
	{% if new_x < 0 or new_y < 0 %}
	
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="No new X or Y position given, parking the active toolhead and activating the new toolhead without moving it."
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={new_t}
	
	
	{% if "x" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	{% if is_printing_gcode %}
	_EXTRUDE T={new_t}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	{% if "xyz" not in printer.toolhead.homed_axes %}
	
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	
	
	{% set svv = printer.save_variables.variables %}
	{% if new_t == default_toolhead %}
	{% set new_xoffset = 0 %}
	{% set new_yoffset = 0 %}
	{% set new_zoffset = 0 %}
	{% else %}
	{% set new_xoffset = -svv.idex_xoffset %}
	{% set new_yoffset = -svv.idex_yoffset %}
	{% set new_zoffset = -svv.idex_zoffset %}
	{% endif %}
	
	{% set xoffset_correction = new_xoffset - printer.named_offsets.toolhead_alignment.x %}
	{% set yoffset_correction = new_yoffset - printer.named_offsets.toolhead_alignment.y %}
	{% set zoffset_correction = new_zoffset - printer.named_offsets.toolhead_alignment.z %}
	
	{% if new_t == 0 %}
	
	{% set t0_act_x = parking_position_t0 %}
	{% set t1_act_x = printer.toolhead.position.x|float %}
	{% set t0_new_x = new_x %}
	{% set t1_new_x = parking_position_t1 %}
	{% set t0_distance = t0_new_x - t0_act_x %}
	{% set t1_distance = t1_new_x - t1_act_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T0."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	
	
	G1 X{t0_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x + (t1_new_x - t1_act_x)} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t0_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T0: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% elif new_t == 1 %}
	
	{% set t0_act_x = printer.toolhead.position.x|float %}
	{% set t1_act_x = parking_position_t1 %}
	{% set t0_new_x = parking_position_t0 %}
	{% set t1_new_x = new_x %}
	{% set t0_distance = t0_act_x - t0_new_x %}
	{% set t1_distance = t1_act_x - t1_new_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T1."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x - t1_distance + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t1_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T1: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% endif %}
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	{% endif %}

[gcode_macro _ZHOP_BEFORE_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_hop = params.Z_HOP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_HOP: {z_hop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="COMBINED_ZHOP G1 Z+{z_hop} E-{e} F{speed * 60}"
	G1 Z+{z_hop} E-{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="ZHOP G1 Z+{z_hop} F{speed * 60}"
	G1 Z+{z_hop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="RETRACT G1 E-{e} F{feedrate}"
	G1 E-{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _ZDROP_AFTER_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_drop = params.Z_DROP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_DROP: {z_drop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="COMBINED_ZDROP G1 Z-{z_drop} E{e} F{speed * 60}"
	G1 Z-{z_drop} E{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="ZDROP G1 Z-{z_drop} F{speed * 60}"
	G1 Z-{z_drop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="EXTRUDE G1 E{e} F{feedrate}"
	G1 E{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _EXTRUDE]
gcode = 
	
	{% set t = params.T|int %}
	
	
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	
	DEBUG_ECHO PREFIX="_EXTRUDE" MSG="G1 E{e} F{feedrate * 60}"
	
	
	G91
	M82
	G92 E0
	G1 E{e} F{feedrate * 60}
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _DEACTIVATE_TOOLHEAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_DEACTIVATE_TOOLHEAD" MSG="TOOLHEAD {toolhead}"
	
	
	{% if toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% endif %}
	
	
	M106.1 S0
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={toolhead}

[delayed_gcode _INIT_TOOLHEADS]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	_IDEX_SINGLE INIT=1
	
	
	{% if printer.fastconfig.settings.dual_carriage.safe_distance is defined %}
	{% if printer.fastconfig.settings.dual_carriage.safe_distance|float < 50 %}
	{ action_emergency_stop("Dual carriage safe_distance seems to be too low!") }
	{% endif %}
	{% else %}
	{ action_emergency_stop("Dual carriage safe_distance not defined!") }
	{% endif %}

[gcode_macro _SET_TOOLHEAD_OFFSET]
description = "Internal use only. Sets the toolhead_alignment offset (and hotend_thermal_expansion offset when configured) for the active/dominant toolhead."
gcode = 
	
	{% set move = params.MOVE|default(0)|int %}
	{% set force_toolhead = params.FORCE_TOOLHEAD|default(-1)|int %}
	
	
	{% if params.T is defined %}
	CONSOLE_ECHO TYPE="error" MSG="_SET_TOOLHEAD_OFFSET called with deprectated T parameter, which is ignored."
	{';$_SET_TOOLHEAD_OFFSET_ignoring_TOOLHEAD_parameter'}
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="active/dominant toolhead: {toolhead}, MOVE: {move}, FORCE_TOOLHEAD: {force_toolhead}"
	
	
	{% if force_toolhead >= 0 %}
	{% set toolhead = force_toolhead %}
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="FORCE_TOOLHEAD applied, using TOOLHEAD: {toolhead}"
	{% endif %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set move = 0 %}
	{% endif %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|int %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X=0 Y=0 MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z=0 MOVE={move} SPEED={z_speed}
	{% else %}
	{% set svv = printer.save_variables.variables %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X={(-svv.idex_xoffset)} Y={(-svv.idex_yoffset)} MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-svv.idex_zoffset)} MOVE={move} SPEED={z_speed}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}

[gcode_macro TOOLSHIFT_CONFIG]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={params.SPEED|default(300)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={params.ACCEL|default(5000)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_retraction VALUE={params.RETRACT|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_extrusion VALUE={params.EXTRUDE|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_feedrate VALUE={params.FEEDRATE|default(7200)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={params.Z_HOP|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zspeed VALUE={params.Z_SPEED|default(25)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_combined_zhop VALUE={true if params.COMBINED_ZHOP|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_sync_fans VALUE={true if params.SYNC_FANS|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_prepurging_timer VALUE={params.AUTO_PURGE_TIME|default(0)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_purge VALUE={params.PURGE|default(25)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_standby_temp VALUE={params.STANDBY_TEMP|default(-1)|float}

[gcode_macro CALCULATE_DC_ENDSTOP]
description = "DEPRECATED: This macro has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."
gcode = 
	CONSOLE_ECHO TITLE="CALCULATE_DC_ENDSTOP has been deprecated" TYPE="error" MSG="The CALCULATE_DC_ENDSTOP has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."

[gcode_macro _VAOC]
variable_is_fixed = True
variable_is_started = False
variable_is_started_at_temp = False
variable_additional_safe_distance = 50
variable_safe_z = 30
variable_auto_z_offset_calibration = True
variable_enable_camera_cooling = True
variable_camera_cooling_fan_speed = 0.3
variable_camera_cooling_temperature = 50
variable_toolchange_travel_speed = 300
variable_toolchange_travel_accel = 5000
variable_adjusting_secondary_toolhead_focus_adjusts_zoffset = False
variable_cache_toolchange_travel_speed = 300
variable_cache_toolchange_travel_accel = 5000
variable_cache_toolchange_zhop = 1.0
variable_t0_toolhead_sensor_enabled = 0
variable_t1_toolhead_sensor_enabled = 0
variable_t0_bowden_sensor_enabled = 0
variable_t1_bowden_sensor_enabled = 0
variable_loaded_skew_profile = ""
variable_gcode_z_offset = 0.0
variable_start_x_offset = 0.0
variable_start_y_offset = 0.0
gcode = 
	_ECHO_VAOC_VARS
variable_expected_camera_x_position = 212.5
variable_expected_camera_y_position = 530.5

[gcode_macro _VAOC_START]
description = Called from the front end. If T0_TEMP, T1_TEMP and BED_TEMP parameter are specified, VAOC calibration will start under real conditions at printing temp.
gcode = 
	
	{% set t0_temp = params.T0_TEMP|default(0)|int %}
	{% set t1_temp = params.T1_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(0)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro SKEW_PROFILE"].loaded_profile|default("") %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=loaded_skew_profile VALUE='"{loaded_skew_profile}"'
	
	
	{% if t0_temp > 0 and t1_temp > 0 and bed_temp > 0 %}
	
	
	{% if not is_fixed %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("VAOC calibration at temp works only with a fixed installed VAOC device.") }
	{% endif %}
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE=0
	{% endif %}
	
	
	START_PRINT EXTRUDER_TEMP={t0_temp},{t1_temp} EXTRUDER_OTHER_LAYER_TEMP={t0_temp},{t1_temp} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp} INITIAL_TOOL=0 TOTAL_LAYER_COUNT=1 X0={(printable_x_max / 2 - 10)} Y0={(printable_y_max / 2 - 10)} X1={(printable_x_max / 2 + 10)} Y1={(printable_y_max / 2 + 10)} TOTAL_TOOLSHIFTS=1 FIRST_X={printable_x_max / 2} FIRST_Y={printable_y_max / 2} MIN_X={(printable_x_max / 2 - 10)} MAX_X={(printable_x_max / 2 + 10)} USED_TOOLS=0,1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=True
	
	{% endif %}
	
	
	_START_VAOC

[gcode_macro _START_VAOC]
description = Called from _VAOC_START. Do not call it manually.
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(printable_x_max/2)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(printable_y_max/2)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	DEBUG_ECHO PREFIX="VAOC_START" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, zcontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_x_offset VALUE={svv.idex_xoffset|default(0.0)|float}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_y_offset VALUE={svv.idex_yoffset|default(0.0)|float}
	
	
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_SAFE_Z_HEIGHT
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_speed VALUE={printer["gcode_macro RatOS"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_accel VALUE={printer["gcode_macro RatOS"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_zhop VALUE={printer["gcode_macro RatOS"].toolchange_zhop|float}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE=0
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"START X_REFERENCE:%.6f Y_REFERENCE:%.6f Z_REFERENCE:%.6f PARK_T0:%.6f PARK_T1:%.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, parking_position_t0, parking_position_t1)}
	
	
	_LED_VAOC_ON
	
	
	
	
	
	
	
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=gcode_z_offset VALUE={printer.gcode_move.homing_origin.z}
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z=0
	
	
	MAYBE_HOME
	M400
	
	
	_LOAD_RATOS_SKEW_PROFILE
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	IDEX_SINGLE
	{% endif %}
	
	
	
	SAVE_GCODE_STATE NAME=vaoc_state
	
	
	RESET_NAMED_OFFSET EVENT=reset_all
	
	
	{% if is_fixed %}
	_SELECT_TOOL T=0 TOOLSHIFT=false
	{% if default_toolhead == 0 %}
	G1 X{idex_xcontrolpoint} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint + safe_distance + additional_safe_distance} F{speed}
	{% else %}
	G1 X{idex_xcontrolpoint - safe_distance - additional_safe_distance} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint} F{speed}
	{% endif %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	{% else %}
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	G1 X{idex_xcontrolpoint} F{speed}
	G1 Y{idex_ycontrolpoint} F{speed}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	
	
	_SELECT_TOOL T={default_toolhead} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	{% if not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={default_toolhead}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=True

[gcode_macro _VAOC_END]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_y = printable_y_max / 2 %}
	{% set saved_gcode_z_offset = printer["gcode_macro _VAOC"].gcode_z_offset|default(0.0)|float %}
	
	DEBUG_ECHO PREFIX="_VAOC_END" MSG="printable_y_max: {printable_y_max}, center_y: {center_y}, safe_z: {safe_z}"
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% set x_offset_change = svv.idex_xoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_x_offset|default(0.0)|float %}
	{% set y_offset_change = svv.idex_yoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_y_offset|default(0.0)|float %}
	{% set offset_change_norm = (x_offset_change ** 2 + y_offset_change ** 2) ** 0.5 %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="VAOC calibration changed the relative XY offset between T0 and T1 by {offset_change_norm|round(3)} mm (ΔX: {x_offset_change|round(3)}, ΔY: {y_offset_change|round(3)})"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	G1 Y{center_y} F{speed}
	
	
	_IDEX_SINGLE INIT=1
	
	
	_LED_VAOC_OFF
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={printer["gcode_macro _VAOC"].cache_toolchange_zhop|float}
	
	
	{% if printer["gcode_macro _VAOC"].is_started_at_temp|default(true)|lower == 'true' %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_bowden_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_bowden_sensor_enabled|int}
	{% endif %}
	{% endif %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro _VAOC"].loaded_skew_profile|default("") %}
	{% if loaded_skew_profile != "" %}
	SKEW_PROFILE LOAD={loaded_skew_profile}
	{% else %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=vaoc_state
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z={saved_gcode_z_offset}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False

[gcode_macro _VAOC_LOAD_TOOL]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set auto_temp_offset = true if params.AUTO_TEMP_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set toolhead_zoffset = svv.idex_zoffset|default(0)|float %}
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move T%s to control point: X%.6f Y%.6f Z%.6f IS_FIXED=%s"' % (t, idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, is_fixed)}
	
	
	{% if not auto_temp_offset and not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={t}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	{% set current_z = printer.toolhead.position.z|float %}
	{% set lowest_toolhead_z = [current_z, current_z - toolhead_zoffset]|min %}
	{% if lowest_toolhead_z < safe_z %}
	G1 Z{[safe_z, safe_z + toolhead_zoffset]|max} F{z_speed}
	{% else %}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	{% endif %}
	
	
	_SELECT_TOOL T={t} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_SET_CAMERA_COOLING]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	
	
	{% set enable_camera_cooling = true if printer["gcode_macro _VAOC"].enable_camera_cooling|default(true)|lower == 'true' else false %}
	{% set camera_cooling_temperature = printer["gcode_macro _VAOC"].camera_cooling_temperature|float %}
	{% set camera_cooling_fan_speed = printer["gcode_macro _VAOC"].camera_cooling_fan_speed|float %}
	
	
	{% if printer.heater_bed.temperature >= camera_cooling_temperature and enable_camera_cooling %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={camera_cooling_fan_speed if t == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={camera_cooling_fan_speed if t == 1 else 0}
	
	
	M106.1 S{camera_cooling_fan_speed}
	
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	{% endif %}

[gcode_macro _VAOC_SET_TOOL]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="_VAOC_SET_TOOL" MSG="IDEX_MODE: {idex_mode}, TOOLHEAD: {toolhead}"
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	{% set x = printer.gcode_move.gcode_position.x|float %}
	{% set y = printer.gcode_move.gcode_position.y|float %}
	{% set z = printer.gcode_move.gcode_position.z|float %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE={x}
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE={y}
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE={z}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Control point was set: X%.6f Y%.6f Z%.6f"' % (x, y, z)}
	
	{% else %}
	
	
	
	{% set move_diff_x = printer.gcode_move.gcode_position.x|float - svv.idex_xcontrolpoint|float %}
	{% set move_diff_y = printer.gcode_move.gcode_position.y|float - svv.idex_ycontrolpoint|float %}
	{% set move_diff_z = printer.gcode_move.gcode_position.z|float - svv.idex_zcontrolpoint|float %}
	
	
	{% set new_x_offset = svv.idex_xoffset - move_diff_x %}
	{% set new_y_offset = svv.idex_yoffset - move_diff_y %}
	{% set new_z_offset = svv.idex_zoffset - move_diff_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE={new_x_offset}
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE={new_y_offset}
	
	{% set z_focus_msg = "" %}
	{% if move_diff_z|abs > 1e-6 %}
	{% if printer["gcode_macro _VAOC"].adjusting_secondary_toolhead_focus_adjusts_zoffset|default(false)|lower == 'true' %}
	{% set z_focus_msg = " (Z offset adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={new_z_offset}
	{% else %}
	{% set z_focus_msg = " (Z offset not adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	{% set new_z_offset = svv.idex_zoffset %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset was set: X%.6f Y%.6f Z%.6f%s"' % (toolhead, new_x_offset, new_y_offset, new_z_offset, z_focus_msg)}
	
	{% endif %}

[gcode_macro _VAOC_MOVE]
gcode = 
	
	{% set x = params.X|default(0)|float %}
	{% set y = params.Y|default(0)|float %}
	{% set z = params.Z|default(0)|float %}
	
	
	G91
	{% if z != 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 Z%.6f F300"' % (z)}
	G1 Z{z} F300
	
	{% else %}
	{% if x <=2 and y <=2 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 X%.6f Y%.6f F18000"' % (x, y)}
	G1 X{x} Y{y} F18000
	{% endif %}
	{% endif %}
	G90

[gcode_macro _VAOC_CALIBRATE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	{% if printer["z_offset_probe"] is defined and is_started %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	
	{% if auto_z_offset %}
	_START_VAOC AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_END
	{% else %}
	_VAOC_LOAD_TOOL T={default_toolhead}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	{% endif %}
	
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_Z_OFFSET
	
	{% endif %}

[gcode_macro _VAOC_PROBE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}
	{% if not auto_z_offset %}
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	{% endif %}
	M400
	_VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT

[gcode_macro _VAOC_Z_OFFSET_PROBE_CURRENT_POSITION]
gcode = 
	
	Z_OFFSET_PROBE PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_DROP=1 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median

[gcode_macro _VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT]
gcode = 
	{% if printer["z_offset_probe"] is defined %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE={last_z}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Z-offset control point set:: %.6f"' % last_z}
	
	{% else %}
	
	
	
	{% set z = svv.idex_zoffsetcontrolpoint|float - last_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={z}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-z)}
	
	
	G0 Z{svv.idex_zcontrolpoint|float} F{z_speed}
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset set: Z %.6f"' % (t, z)}
	
	{% endif %}
	
	{% endif %}

[gcode_macro _VAOC_ECHO_Z_OFFSET]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s toolhead z-offset %.6f"' % (1 if default_toolhead == 0 else 0, svv.idex_zoffset)}
	{% if svv.idex_zoffset|abs < 0.02 %}
	CONSOLE_ECHO TITLE={'"Perfect toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="You have a perfect toolhead z-offset!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.02 and svv.idex_zoffset|abs < 0.05 %}
	CONSOLE_ECHO TITLE={'"Good toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is good!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.05 and svv.idex_zoffset|abs < 0.1 %}
	CONSOLE_ECHO TITLE={'"High toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset could be better._N_Use minimum 0.3mm first layer height for copy and mirror mode prints." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.1 and svv.idex_zoffset|abs < 0.2 %}
	CONSOLE_ECHO TITLE={'"Bad toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is bad._N_Copy and mirror mode prints are not recommended with it." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.2 %}
	CONSOLE_ECHO TITLE={'"Unacceptable toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is unacceptable._N_Do not print in copy and mirror mode with it." TYPE="alert"
	{% endif %}
	RATOS_ECHO PREFIX="VAOC" MSG="Toolhead z-offset calibration done!"

[gcode_macro _VAOC_CALIBRATE_TEMP_OFFSET]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if is_fixed and is_started and printer["z_offset_probe"] is defined and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	_VAOC_LOAD_TOOL T={default_toolhead} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_NOZZLE_TEMP_OFFSETS
	
	{% endif %}

[gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET=0
	
	
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	M400

[gcode_macro _VAOC_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(150)|float %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Probing with nozzle temperature {temp}°C..."
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	
	
	G0 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _VAOC_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set msg = '"T0 expansion coefficient %.6fmm_N_T1 expansion coefficient %.6fmm"' % (svv.nozzle_expansion_coefficient_t0, svv.nozzle_expansion_coefficient_t1) %}
	CONSOLE_ECHO TITLE="Nozzle expansion coefficients:" MSG={msg} TYPE="success"

[gcode_macro _VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - expected_camera_x_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC x-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_xcontrolpoint, expected_camera_x_position)) }
	{% endif %}
	{% if (idex_ycontrolpoint - expected_camera_y_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC y-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_ycontrolpoint, expected_camera_y_position)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - printer.gcode_move.gcode_position.x|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected y-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_xcontrolpoint, printer.gcode_move.gcode_position.x|float)) }
	{% endif %}
	{% if (idex_ycontrolpoint - printer.gcode_move.gcode_position.y|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected x-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_ycontrolpoint, printer.gcode_move.gcode_position.y|float)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_SAFE_Z_HEIGHT]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set idex_zoffsetcontrolpoint = svv.idex_zoffsetcontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_SAFE_Z_HEIGHT" MSG={'"idex_zcontrolpoint: %.6f, idex_zoffsetcontrolpoint: %.6f"' % (idex_zcontrolpoint, idex_zoffsetcontrolpoint)}
	
	{% if safe_z < idex_zcontrolpoint + 2 or safe_z < idex_zoffsetcontrolpoint + 2 %}
	{action_raise_error("VAOC safe_z value (%.3f) is too low, it must be higher than %.3f" % (safe_z, [idex_zoffsetcontrolpoint + 2, idex_zcontrolpoint + 2]|max))}
	{% endif %}

[gcode_macro _VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED]
gcode = 
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T0. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T1. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_RESET]
gcode = 
	DEBUG_ECHO PREFIX="_VAOC_RESET" MSG="running template-emitted _VAOC_RESET macro"
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE=212.5
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE=530.5
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE=10
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE=0
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE=0.0
	
	RESET_DC_ENDSTOP_CONFIGURATION
	RESET_Y_MAX_ADJUSTMENT
	
	
	CONSOLE_ECHO TITLE="VAOC Configuration Reset" MSG="VAOC configuration has been reset. You must RESTART klipper for the changes to take effect,_N_then re-calibrate VAOC."

[gcode_macro _ECHO_VAOC_VARS]
description = Echo VAOC variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro _VAOC"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro _VAOC_SWITCH_LED]
gcode = 
	{% if params.STATE|default(0)|int == 1 %}
	_LED_VAOC_ON
	{% else %}
	_LED_VAOC_OFF
	{% endif %}

[gcode_macro Z_PROBE_TEST_T0]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T0
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST_T1]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T1
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	
	
	_VAOC_Z_PROBE_TEST_EVALUATE
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro _VAOC_Z_PROBE_LOOP]
gcode = 
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_SHAKE_IT
	_VAOC_START

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if primary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T0. Retried {primary_retries} time(s)."
	{% endif %}
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	
	{% if (primary_range - secondary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 is drifting significantly more than T1."
	{% endif %}
	{% if (secondary_range - primary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 is drifting significantly more than T0."
	{% endif %}
	
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T0]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T1]
gcode = 
	
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _SHAKE_IT]
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	_Z_HOP
	{% for i in range(3) %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 + 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 + 1}
	{% endfor %}
	{% for i in range(2) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 + 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 + 50}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 1}
	{% endfor %}
	{% endfor %}

[gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 retries updated: {new_retries}"

[gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 retries updated: {new_retries}"

[gcode_macro _CLEAR_PRIMARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _CLEAR_SECONDARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _VAOC_TEST_Z_OFFSET]
gcode = 
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}

[delayed_gcode _IDEX_INIT]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	VERIFY_HYBRID_INVERTED

[gcode_macro Z_TILT_ADJUST]
rename_existing = Z_TILT_ADJUST_ORIG
gcode = 
	
	{% set beacon_contact_z_tilt_adjust_samples = printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust_samples|default(2)|int %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(true)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	_IDEX_SINGLE
	
	_SELECT_TOOL T={printer["gcode_macro RatOS"].default_toolhead|default(0)|int} TOOLSHIFT=false
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_tilt_adjust %}
	Z_TILT_ADJUST_ORIG PROBE_METHOD=contact SAMPLES={beacon_contact_z_tilt_adjust_samples}
	{% else %}
	Z_TILT_ADJUST_ORIG
	{% endif %}
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if idex_mode == "copy" %}
	_IDEX_COPY
	{% elif idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[stepper_x]
position_max = 500
position_endstop = -59.6
position_min = -59.6
step_pin = PF13
dir_pin = x_dir_pin
enable_pin = !PF14
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t0:PA2

[stepper_y]
position_max = 533.65
position_min = -14.35
position_endstop = -14.35
step_pin = PG0
dir_pin = !y_dir_pin
enable_pin = !PF15
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = PG9

[stepper_z]
position_max = 500
position_min = -7
step_pin = PC13
dir_pin = !z0_dir_pin
enable_pin = !PF1
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4
homing_speed = 10
endstop_pin = probe:z_virtual_endstop

[z_tilt]
z_positions = 
	0,0
	250,500
	500,0
points = 
	20, 10
	480, 230
	20, 450
horizontal_move_z = 20
retries = 10
retry_tolerance = 0.02
speed = 600

[extruder]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t0:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t0:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t0:PD3
dir_pin = toolboard_t0:e_dir_pin
enable_pin = !toolboard_t0:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[firmware_retraction]
retract_speed = 60
unretract_extra_length = 0
unretract_speed = 60
retract_length = 0.2

[extruder1]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t1:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t1:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t1:PD3
dir_pin = toolboard_t1:e_dir_pin
enable_pin = !toolboard_t1:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[resonance_tester]
accel_chip_x = lis2dw toolboard_t0
accel_chip_y = lis2dw toolboard_t0
probe_points = 
	250,250,20

[tmc5160 stepper_x]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC4
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 dual_carriage]
stealthchop_threshold = 0
interpolate = True
cs_pin = PF2
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y]
stealthchop_threshold = 0
interpolate = True
cs_pin = PD11
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y1]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC7
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[stepper_y1]
step_pin = PG4
dir_pin = y1_dir_pin
enable_pin = !PA2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46

[tmc2209 stepper_z]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE4
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[tmc2209 stepper_z1]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE1
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z1]
step_pin = PE2
dir_pin = !z1_dir_pin
enable_pin = !PD4
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 stepper_z2]
stealthchop_threshold = 0
interpolate = True
uart_pin = PD3
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z2]
step_pin = PE6
dir_pin = !z2_dir_pin
enable_pin = !PE0
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 extruder]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t0:PB3
run_current = 0.707
sense_resistor = 0.11

[tmc2209 extruder1]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t1:PB3
run_current = 0.707
sense_resistor = 0.11

[beacon]
serial = /dev/beacon
x_offset = 0
y_offset = 27.5
mesh_main_direction = x
mesh_runs = 1
mesh_cluster_size = 0
speed = 15.
lift_speed = 80.
contact_max_hotend_temperature = 275
contact_mesh_min = 20,20
contact_mesh_max = 480,480

[beacon_user_z_offset]

[beacon_mesh]

[beacon_true_zero_correction]

[beacon_adaptive_heat_soak]

[delayed_gcode _BEACON_INIT]
initial_duration = 1
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	_BEACON_MESH_INIT
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_coefficient_multiplier
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_applied_offset
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=beacon_saved_runtime_offset
	{% if printer["gcode_macro RatOS"].beacon_contact_expansion_multiplier is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_contact_expansion_multiplier is no longer used, please remove it from your config file."
	{% endif %}
	{% if printer["gcode_macro RatOS"].beacon_scan_compensation_resolution is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_scan_compensation_resolution is no longer used, please remove it from your config file."
	{% endif %}

[gcode_macro BEACON_RATOS_CALIBRATION]
gcode = 
	RATOS_ECHO MSG="Did you mean BEACON_RATOS_CALIBRATE?"

[gcode_macro BEACON_RATOS_CALIBRATE]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	BEACON_INITIAL_CALIBRATION _AUTOMATED=True
	
	{% if beacon_contact_start_print_true_zero %}
	BEACON_POKE_TEST _AUTOMATED=True
	_BEACON_CHECK_POKE
	{% if printer["dual_carriage"] is not defined %}
	BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET _AUTOMATED=True
	{% endif %}
	{% endif %}
	
	{% set already_heated = False %}
	
	
	{% if beacon_contact_start_print_true_zero and beacon_scan_compensation_enable %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% set already_heated = True %}
	{% endif %}
	
	
	BEACON_FINAL_CALIBRATION _AUTOMATED=True _AUTOMATED_ALREADY_HEATED={already_heated} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	{% if beacon_contact_start_print_true_zero %}
	{% if printer["dual_carriage"] is not defined %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	_BEACON_ECHO_POKE
	{% endif %}
	RATOS_ECHO MSG="Beacon calibration finished!"
	
	
	_LED_BEACON_CALIBRATION_END
	
	
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG

[gcode_macro BEACON_INITIAL_CALIBRATION]
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Initial beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro BEACON_FINAL_CALIBRATION]
description = Runs BEACON_AUTO_CALIBRATE after heating the bed and chamber to specified temperatures. This creates a beacon model under reference conditions for future use.
	This macro will skip calibration if both the beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero settings are enabled, because a new
	model will be calibrated automatically at the start of each print. Use FORCE=True to override this check.
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set already_heated = true if params._AUTOMATED_ALREADY_HEATED|default(false)|lower == 'true' else false %}
	{% set force = params.FORCE|default('false')|lower in ('1', 'true', 'yes') %}
	
	
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default('false')|lower == "true" %}
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero and not force %}
	RATOS_ECHO MSG="BEACON_FINAL_CALIBRATION skipped, not needed because beacon_contact_calibrate_model_on_true_zero is enabled. Use FORCE=True to override."
	{% else %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	{% if chamber_temp > 0 and not already_heated %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	{% if not already_heated %}
	
	G0 Z2.5 F{z_hop_speed}
	
	
	RATOS_ECHO MSG="Waiting for calibration temperature..."
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	{% if beacon_adaptive_heat_soak %}
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,3600]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_Z_HOP
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Final beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	{% endif %}

[gcode_macro BEACON_POKE_TEST]
variable_poke_result_1 = -1
variable_poke_result_2 = -1
variable_poke_result_3 = -1
variable_poke_result_4 = -1
variable_poke_result_5 = -1
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_1 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_2 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_3 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_4 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_5 VALUE=-1
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G0 Z5 F{z_hop_speed}
	
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=1
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=2
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=3
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=4
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=5
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Beacon poke test finished!"
	{% if not automated %}
	_BEACON_ECHO_POKE
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro _BEACON_PROBE_POKE]
gcode = 
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	BEACON_POKE speed=3 top=5 bottom={poke_bottom}
	BEACON_QUERY

[gcode_macro _BEACON_STORE_POKE]
gcode = 
	
	{% set i = params.I|default(1)|int %}
	
	
	{% set last_z = printer.beacon.last_poke_result|default(0)|float %}
	
	
	{% if printer.beacon.last_poke_result|lower != "none" %}
	{% if printer.beacon.last_poke_result.error == 0 %}
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE={"poke_result_%s" % i} VALUE={printer.beacon.last_poke_result.latency}
	{% endif %}
	{% endif %}

[gcode_macro _BEACON_CHECK_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% if p1 == -1 or p2 == -1 or p3 == -1 or p4 == -1 or p5 == -1 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test error!") }
	{% endif %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	{% if avg > 6 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test failed!") }
	{% endif %}

[gcode_macro _BEACON_ECHO_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	
	
	{% if avg <= 1 %}
	{% set type = "success" %}
	{% set note = "Extremely low noise, rarely achieved" %}
	{% elif avg > 1 and avg <= 4 %}
	{% set type = "info" %}
	{% set note = "Excellent performance for a typical printer" %}
	{% elif avg > 4 and avg <= 8 %}
	{% set type = "warning" %}
	{% set note = "Acceptable performance, machine may have considerable cyclic axis noise" %}
	{% elif avg > 8 and avg <= 11 %}
	{% set type = "alert" %}
	{% set note = "Not ideal, may want to verify proper mounting or use thinner stackups" %}
	{% elif avg > 11 %}
	{% set type = "alert" %}
	{% set note = "Reason for concern, present setup may be risky to continue with" %}
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon poke test result:" TYPE={type} MSG={'"Average latency: %.2f_N_%s"' % (avg, note)}

[gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Nozzle temperature offset calibration..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET=0
	
	
	{% if not automated %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing with nozzle temperature {temp}°C..."
	PROBE PROBE_METHOD=contact PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median
	BEACON_QUERY
	
	
	G0 Z5 F{z_speed}

[gcode_macro _BEACON_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer.beacon.last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{default_toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% if default_toolhead == 0 %}
	CONSOLE_ECHO TYPE="info" MSG={'"T0 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t0}
	{% else %}
	CONSOLE_ECHO TYPE="info" MSG={'"T1 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t1}
	{% endif %}

[gcode_macro _BEACON_SET_NOZZLE_TEMP_OFFSET]
description = "Set the thermal expansion z offset for the active toolhead based on the current extruder target temperature and thermal expansion coefficient."
gcode = 
	{% if params.RESET is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The RESET parameter is no longer supported and has no effect."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% if params.TOOLHEAD is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The TOOLHEAD parameter is no longer supported and has no effect. The macro now automatically determines the current toolhead."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	{% if beacon_contact_expansion_compensation %}
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set nozzle_expansion_coefficient_t0 = svv.nozzle_expansion_coefficient_t0|default(0)|float %}
	{% if printer["dual_carriage"] is defined %}
	{% set nozzle_expansion_coefficient_t1 = svv.nozzle_expansion_coefficient_t1|default(0)|float %}
	{% endif %}
	
	
	{% set temp = printer['extruder' if toolhead == 0 else 'extruder1'].target|float %}
	
	
	{% set temp_delta = temp - beacon_contact_true_zero_temp %}
	{% set expansion_coefficient = nozzle_expansion_coefficient_t0 if toolhead == 0 else nozzle_expansion_coefficient_t1 %}
	{% set expansion_offset = temp_delta * (expansion_coefficient / 100) %}
	
	
	SET_NAMED_OFFSET NAME=hotend_thermal_expansion Z={expansion_offset} MOVE=1 MOVE_SPEED={z_speed}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG={'"Nozzle expansion offset of %.6fmm applied to T%s"' % (expansion_offset, toolhead)}
	DEBUG_ECHO PREFIX="_BEACON_SET_NOZZLE_TEMP_OFFSET" MSG="toolhead: {toolhead}, coefficient: {expansion_coefficient|round(6)}, temp_delta: {temp_delta|round(1)},  expansion_offset: {expansion_offset|round(6)}"
	
	{% endif %}

[gcode_macro BEACON_MEASURE_BEACON_OFFSET]
variable_needs_compensation = False
variable_reference_z = 0.0
variable_front = 0.0
variable_front_left = 0.0
variable_front_right = 0.0
variable_back = 0.0
variable_back_left = 0.0
variable_back_right = 0.0
variable_right = 0.0
variable_left = 0.0
variable_margin_x = 40
variable_margin_y = 40
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=False
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Measure beacon offset..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="center"
	
	
	G0 X{margin_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_left"
	
	
	G0 X{safe_home_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front"
	
	
	G0 X{(printable_x_max - margin_x)} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_right"
	
	
	G0 X{safe_home_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back"
	
	
	G0 X{margin_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_left"
	
	
	G0 X{margin_x} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="left"
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_BEACON_ECHO_BEACON_OFFSET
	
	
	_LED_BEACON_CALIBRATION_END
	
	{% endif %}

[gcode_macro _BEACON_STORE_BEACON_OFFSET]
gcode = 
	
	{% set location = params.LOCATION|lower %}
	
	
	{% set last_z = printer.beacon.last_offset_result["delta"]|default(0)|float %}
	
	
	{% if location == "center" %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE={location} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_BEACON_OFFSET]
gcode = 
	
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float * 1000 %}
	{% set front_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_left|default(0)|float * 1000 %}
	{% set front = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front|default(0)|float * 1000 %}
	{% set front_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_right|default(0)|float * 1000 %}
	{% set right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].right|default(0)|float * 1000 %}
	{% set back_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_right|default(0)|float * 1000 %}
	{% set back = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back|default(0)|float * 1000 %}
	{% set back_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_left|default(0)|float * 1000 %}
	{% set left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].left|default(0)|float * 1000 %}
	
	{% set line_1 = "Front left:    %.6fμm" % (front_left) %}
	{% set line_2 = "Front center:  %.6fμm" % (front) %}
	{% set line_3 = "Front right:   %.6fμm" % (front_right) %}
	{% set line_4 = "Left center:   %.6fμm" % (left) %}
	{% set line_5 = "Right center:  %.6fμm" % (right) %}
	{% set line_6 = "Back left:     %.6fμm" % (back_left) %}
	{% set line_7 = "Back center:   %.6fμm" % (back) %}
	{% set line_8 = "Back right:    %.6fμm" % (back_right) %}
	
	{% set max_value = [(front_left|abs), (front|abs), (front_right|abs), (left|abs), (right|abs), (back_left|abs), (back|abs), (back_right|abs)]|max %}
	{% if max_value <= 50 %}
	{% set type = "success" %}
	{% set recommendation = "Very low beacon offset: %.6fμm._N_No beacon scan compensation needed." % max_value %}
	{% elif max_value > 50 and max_value <= 100 %}
	{% set type = "info" %}
	{% set recommendation = "Low beacon offset: %.6fμm._N_You may experience first layer inconsistensies, consider beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 100 and max_value <= 150 %}
	{% set type = "warning" %}
	{% set recommendation = "High beacon offset: %.6fμm._N_High chance of first layer problems, beacon scan compensation is highly encouraged." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 150 and max_value <= 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Very High beacon offset: %.6fμm._N_You will encounter first layer problems on large prints unless you activate beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Extremely high beacon offset: %.6fμm._N_You have significant scan/contact inconsistency which is indicative of mechanical problems, please investigate before resorting to software compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon offset relative to the center" TYPE={type} MSG={'"_N_%s_N__N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s"' % (recommendation, line_1, line_2, line_3, line_4, line_5, line_6, line_7, line_8)}

[gcode_macro BEACON_CREATE_SCAN_COMPENSATION_MESH]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set profile = params.PROFILE|default("auto")|string %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set keep_temp_meshes = params.KEEP_TEMP_MESHES|default(0) %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' %}
	{% set desired_spacing = printer["gcode_macro RatOS"].beacon_scan_compensation_desired_spacing|float %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	
	{% if not beacon_scan_compensation_enable %}
	RATOS_ECHO MSG="Beacon scan compensation is disabled!"
	
	{% else %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	
	
	RATOS_ECHO MSG="Please wait..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	G1 Z2.5 F{z_speed}
	{% if beacon_adaptive_heat_soak %}
	
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,9000]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if not (beacon_adaptive_heat_soak or bed_heat_soak_time > 0) %}
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if printer.z_tilt is defined %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% endif %}
	{% if printer.quad_gantry_level is defined %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% endif %}
	
	
	_BEACON_CREATE_SCAN_COMPENSATION_MESH_CORE PROFILE="{profile}" DESIRED_SPACING={desired_spacing} CHAMBER_TEMP={chamber_temp} KEEP_TEMP_MESHES={keep_temp_meshes}
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	{% if automated %}
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon scan compensation mesh created!"
	
	
	{% if not automated %}
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED]
gcode = 
	
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED" MSG="beacon_scan_compensation_profile {beacon_scan_compensation_profile}, beacon_scan_compensation_enable {beacon_scan_compensation_enable}"
	
	{% if beacon_scan_compensation_enable %}
	BEACON_APPLY_SCAN_COMPENSATION PROFILE="{beacon_scan_compensation_profile}"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL]
gcode = 
	
	{% set beacon_contact_start_print_true_zero = params.BEACON_CONTACT_START_PRINT_TRUE_ZERO|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = params.beacon_contact_calibrate_model_on_true_zero|lower == 'true' %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and not printer.beacon.model %}
	{% set beacon_model_required_for_true_zero = beacon_contact_start_print_true_zero and not beacon_contact_calibrate_model_on_true_zero %}
	{% set beacon_model_required_for_homing =
	printer.fastconfig.settings.stepper_z.endstop_pin == 'probe:z_virtual_endstop'
	and (( printer.fastconfig.settings.beacon.home_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower != 'true')
	or ( printer.fastconfig.settings.beacon.default_probe_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower != 'true' )) %}
	{% if beacon_model_required_for_homing or beacon_model_required_for_true_zero %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("An active Beacon model is required. Have you performed initial Beacon calibration?") }
	{% endif %}
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION]
gcode = 
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set bed_temp_mismatch_is_error = true if printer["gcode_macro RatOS"].beacon_scan_compensation_bed_temp_mismatch_is_error|default(false)|lower == 'true' else false %}
	
	{% set bed_temp = params.BED_TEMP|default(0)|float %}
	{% if bed_temp == 0 %}
	{% set bed_temp = printer.heater_bed.temperature %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_PREFLIGHT_CHECK_BEACON" MSG="beacon_scan_compensation_profile={beacon_scan_compensation_profile}, beacon_scan_compensation_enable={beacon_scan_compensation_enable}, bed_temp={bed_temp}"
	
	{% if beacon_scan_compensation_enable %}
	_VALIDATE_COMPENSATION_MESH_PROFILE PROFILE="{beacon_scan_compensation_profile}" TITLE="Check Beacon scan compensation profile" SUBJECT="Configured compensation profile '{beacon_scan_compensation_profile}'" COMPARE_BED_TEMP={bed_temp} COMPARE_BED_TEMP_IS_ERROR={bed_temp_mismatch_is_error}
	{% endif %}

[gcode_macro _BEACON_MAYBE_SCAN_COMPENSATION]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set needs_scan_compensation = true if printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].needs_compensation|default(false)|lower == 'true' else false %}
	
	{% if needs_scan_compensation %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% endif %}

[gcode_macro _BEACON_HOME_AND_ABL]
gcode = 
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	{% if needs_rehoming %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}

[gcode_macro SAVE_Z_OFFSET]
description = Deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead, or in Mainsail use the SAVE button in the Z-OFFSET section.
gcode = 
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default('false')|lower == 'true' %}
	{% set msg = "SAVE_Z_OFFSET is deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead,_N_or in Mainsail use the SAVE button in the Z-OFFSET section."%}
	{% if not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% set msg = msg + "_N_You must then use the SAVE_CONFIG command to persist the change." %}
	{% endif %}
	CONSOLE_ECHO TYPE="error" MSG="{msg}"

[gcode_macro _BEACON_OFFSET_COMPARE]
gcode = 
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing..."
	
	
	BEACON_OFFSET_COMPARE SAMPLES_DROP=1 SAMPLES=3
	BEACON_QUERY

[fan]
pin = rpi:gpio4

[fan_generic part_fan_t0]
pin = PA8
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[fan_generic part_fan_t1]
pin = PE5
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[heater_fan toolhead_cooling_fan_t0]
heater = extruder
shutdown_speed = 1
pin = toolboard_t0:PB4

[heater_fan toolhead_cooling_fan_t1]
heater = extruder1
shutdown_speed = 1
pin = toolboard_t1:PB4

[controller_fan controller_fan]
pin = dinghy:PA4
tachometer_pin = dinghy:PC15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[z_offset_probe]
pin = ^PG10
z_offset = -7
y_offset = 0
x_offset = 37.5
speed = 10
samples = 3
sample_retract_dist = 5
lift_speed = 10.0
samples_result = median
samples_tolerance = 0.2
samples_tolerance_retries = 5

[neopixel vaoc_led]
pin = PB10
chain_count = 6
color_order = GRB

[heater_fan vaoc_fan]
pin = PD13
heater = heater_bed
fan_speed = 1.0
heater_temp = 50

[fan_generic filter]
pin = !PD14
enable_pin = PD15

[gcode_macro T0]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = True
variable_color = "7bff33"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = -32.6
variable_parking_position = -57.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=0 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[gcode_macro T1]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = False
variable_color = "0ea5e9"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = 532.6
variable_parking_position = 557.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=1 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[save_variables]
filename = /home/pi/printer_data/config/ratos-variables.cfg

[mcu dinghy]
serial = /dev/serial/by-id/usb-Klipper_stm32f072xb_Dragon_dinghy-if00

[temperature_sensor th0]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA0

[temperature_sensor th1]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA1

[temperature_sensor th2]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA2

[temperature_sensor th3]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA3

[controller_fan CTL2]
pin = dinghy:PB14
tachometer_pin = dinghy:PB15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[mcu plasma]
serial = /dev/serial/by-id/usb-Klipper_rp2040_Plasma-if00

[neopixel Chamber_Lights]
pin = plasma:gpio15
chain_count = 140
color_order = GRBW
initial_red = 0.0
initial_green = 0.0
initial_blue = 0.0
initial_white = 0.1

[beacon model default]
model_coef = 1.5287863993594841,
	1.9289099639750602,
	0.8838828622507556,
	0.25554883784260735,
	-0.015171504024913506,
	0.3044946127013882,
	0.15820427856566457,
	-0.25262403959326246,
	0.042488512846660914,
	0.16662470122520964
model_domain = 1.842634574664148e-07,1.9339206373083917e-07
model_range = 0.200000,5.000000
model_temp = 13.222247
model_offset = 0.00000

[bed_mesh default]
version = 1
points = 
	0.016163, 0.016713, 0.001923, -0.017658, -0.031574, -0.032498, -0.030898, -0.032177, -0.035213, -0.031148, -0.021322, -0.016924, -0.015012, -0.013911, -0.012197, -0.012583, -0.010489, -0.007529, -0.003986, -0.000980, 0.005518, 0.014442, 0.027426, 0.034677, 0.037410, 0.040391, 0.041842, 0.040369, 0.037615, 0.030776, 0.027664, 0.022856, 0.016892, 0.015398, 0.014717, 0.006921, 0.001532, 0.000731, 0.008657, 0.014036
	0.005356, -0.005066, -0.016998, -0.029668, -0.038334, -0.043672, -0.041139, -0.042488, -0.045199, -0.039432, -0.028746, -0.023642, -0.024058, -0.022802, -0.019679, -0.018514, -0.018102, -0.016476, -0.012722, -0.010077, -0.001809, 0.007180, 0.019853, 0.027754, 0.029964, 0.033626, 0.036783, 0.032018, 0.029372, 0.020847, 0.017634, 0.011926, 0.009013, 0.009254, 0.007972, -0.001380, -0.006940, -0.002160, 0.006135, 0.008330
	-0.004900, -0.006720, -0.021914, -0.039691, -0.050459, -0.050377, -0.046281, -0.048755, -0.054708, -0.051499, -0.033927, -0.027632, -0.030243, -0.031447, -0.024387, -0.021408, -0.020382, -0.018068, -0.015930, -0.013877, -0.006099, 0.003479, 0.013310, 0.024783, 0.025522, 0.030849, 0.033573, 0.031409, 0.025495, 0.016683, 0.011264, 0.008805, 0.006856, 0.008059, 0.007305, 0.002581, -0.003320, -0.003239, 0.004691, 0.010045
	-0.008791, -0.019334, -0.029149, -0.040533, -0.051698, -0.058235, -0.054863, -0.054840, -0.055692, -0.049534, -0.036731, -0.033053, -0.035667, -0.035315, -0.024352, -0.023825, -0.022538, -0.020438, -0.018207, -0.015389, -0.006515, 0.001966, 0.013591, 0.019434, 0.020600, 0.024967, 0.029425, 0.026812, 0.018980, 0.007878, 0.002360, 0.000859, 0.003849, 0.005649, 0.005421, -0.000416, -0.007906, -0.003164, 0.007582, 0.010039
	-0.018512, -0.018210, -0.033932, -0.050501, -0.061588, -0.064139, -0.060236, -0.062528, -0.067065, -0.062039, -0.045815, -0.039448, -0.040521, -0.042080, -0.033870, -0.030878, -0.027396, -0.024548, -0.021298, -0.020041, -0.011880, -0.002847, 0.008689, 0.015857, 0.015934, 0.018697, 0.022439, 0.022106, 0.017916, 0.005879, 0.001037, -0.001311, -0.001335, 0.001897, 0.003656, 0.000561, -0.006084, -0.005683, 0.000338, 0.006245
	-0.028558, -0.036721, -0.044680, -0.054969, -0.066140, -0.075045, -0.073515, -0.073161, -0.075696, -0.068963, -0.058892, -0.053111, -0.050990, -0.048040, -0.041262, -0.037419, -0.034866, -0.031845, -0.029787, -0.026524, -0.017896, -0.009322, -0.001010, 0.005819, 0.008058, 0.010456, 0.013266, 0.012529, 0.007992, -0.001491, -0.006769, -0.009303, -0.005980, -0.003567, -0.003340, -0.011496, -0.018818, -0.014808, -0.004181, -0.000733
	-0.037253, -0.038393, -0.053129, -0.066170, -0.075959, -0.079233, -0.077475, -0.082688, -0.086779, -0.083983, -0.069005, -0.062542, -0.060351, -0.058481, -0.051101, -0.043149, -0.039837, -0.037039, -0.034698, -0.031301, -0.024330, -0.019786, -0.010285, -0.001967, 0.002812, 0.004899, 0.009657, 0.006946, 0.002155, -0.005232, -0.009851, -0.011218, -0.011509, -0.010097, -0.010293, -0.013175, -0.018958, -0.019846, -0.012107, -0.005641
	-0.046584, -0.055590, -0.062606, -0.069218, -0.080399, -0.087414, -0.089037, -0.092376, -0.095115, -0.088957, -0.080802, -0.073290, -0.068741, -0.064591, -0.054452, -0.048270, -0.045916, -0.044559, -0.042047, -0.039605, -0.032667, -0.025789, -0.019495, -0.012773, -0.006697, -0.003025, 0.001413, 0.000817, -0.004738, -0.013008, -0.017605, -0.018191, -0.018524, -0.016356, -0.016750, -0.021992, -0.028943, -0.025791, -0.016146, -0.010447
	-0.051029, -0.051677, -0.068218, -0.079622, -0.088590, -0.089331, -0.089731, -0.096072, -0.105329, -0.100771, -0.087584, -0.079320, -0.075489, -0.072081, -0.064183, -0.054662, -0.048601, -0.049465, -0.047050, -0.045011, -0.040009, -0.032508, -0.025212, -0.018144, -0.011996, -0.008136, -0.003187, -0.003214, -0.006646, -0.013044, -0.019446, -0.020615, -0.022270, -0.021298, -0.020215, -0.020946, -0.026034, -0.026598, -0.021025, -0.012328
	-0.057184, -0.064908, -0.073093, -0.081584, -0.091971, -0.097048, -0.097688, -0.101869, -0.106651, -0.102162, -0.095658, -0.087938, -0.082718, -0.077017, -0.069608, -0.060682, -0.056889, -0.056864, -0.054260, -0.052011, -0.044563, -0.038927, -0.031943, -0.025832, -0.021170, -0.014319, -0.009046, -0.008543, -0.011751, -0.020287, -0.026608, -0.027259, -0.029120, -0.025549, -0.023221, -0.027725, -0.032477, -0.028427, -0.019343, -0.014932
	-0.060411, -0.062241, -0.080781, -0.090744, -0.100903, -0.099702, -0.098468, -0.104236, -0.116853, -0.112701, -0.102623, -0.095036, -0.091407, -0.089871, -0.079701, -0.070222, -0.064325, -0.063875, -0.062248, -0.059396, -0.052699, -0.047589, -0.041526, -0.028442, -0.024526, -0.019549, -0.015403, -0.014251, -0.017989, -0.022824, -0.027328, -0.029155, -0.033315, -0.032426, -0.027619, -0.030776, -0.033688, -0.032458, -0.027219, -0.019649
	-0.067541, -0.076514, -0.082321, -0.088656, -0.099968, -0.104930, -0.105875, -0.109051, -0.115531, -0.112996, -0.105760, -0.100390, -0.096171, -0.090011, -0.080050, -0.073632, -0.067451, -0.067031, -0.065225, -0.062471, -0.056370, -0.050129, -0.041626, -0.030801, -0.027579, -0.022472, -0.014826, -0.015306, -0.020316, -0.025953, -0.030661, -0.034103, -0.035502, -0.032738, -0.031311, -0.037314, -0.041306, -0.035280, -0.027449, -0.020395
	-0.068162, -0.069269, -0.088235, -0.096809, -0.103385, -0.103271, -0.102507, -0.109535, -0.123412, -0.118580, -0.106622, -0.099580, -0.097644, -0.096978, -0.087259, -0.077196, -0.068978, -0.067016, -0.063682, -0.062548, -0.057901, -0.052295, -0.044088, -0.032703, -0.026551, -0.021607, -0.014155, -0.013747, -0.017390, -0.022419, -0.027444, -0.030877, -0.033450, -0.032423, -0.032041, -0.033598, -0.035149, -0.034054, -0.029356, -0.020998
	-0.069473, -0.075924, -0.083569, -0.089648, -0.101235, -0.105828, -0.109144, -0.112613, -0.117233, -0.114186, -0.107090, -0.098616, -0.097084, -0.094257, -0.086773, -0.076409, -0.069532, -0.066472, -0.060956, -0.059191, -0.052886, -0.047752, -0.041275, -0.032437, -0.027780, -0.020398, -0.012061, -0.010133, -0.014056, -0.021528, -0.027924, -0.030605, -0.030609, -0.026068, -0.029346, -0.033991, -0.038254, -0.030610, -0.021109, -0.015885
	-0.068084, -0.066409, -0.083944, -0.094013, -0.102504, -0.105274, -0.106036, -0.112090, -0.121664, -0.117824, -0.104850, -0.097467, -0.098833, -0.098622, -0.089603, -0.078147, -0.068143, -0.066300, -0.061573, -0.057727, -0.054825, -0.048625, -0.040164, -0.030532, -0.025948, -0.020264, -0.014196, -0.010702, -0.013794, -0.019775, -0.026095, -0.028838, -0.030254, -0.027944, -0.027980, -0.030915, -0.032446, -0.028861, -0.023732, -0.014676
	-0.065280, -0.068669, -0.076948, -0.082397, -0.094986, -0.105117, -0.107099, -0.108954, -0.112557, -0.110326, -0.100725, -0.096325, -0.096240, -0.092388, -0.081185, -0.071682, -0.065650, -0.062250, -0.057027, -0.054691, -0.048349, -0.042069, -0.032712, -0.027728, -0.023396, -0.018458, -0.008357, -0.005699, -0.011447, -0.020033, -0.026387, -0.030280, -0.028443, -0.023735, -0.023838, -0.031580, -0.034204, -0.027768, -0.018029, -0.010628
	-0.061662, -0.057052, -0.075163, -0.086710, -0.094182, -0.097544, -0.098814, -0.105908, -0.114460, -0.111718, -0.097559, -0.091614, -0.093860, -0.093098, -0.081687, -0.069410, -0.064117, -0.062745, -0.055603, -0.051413, -0.048043, -0.040363, -0.031842, -0.023420, -0.017470, -0.012600, -0.008163, -0.003898, -0.007635, -0.013254, -0.019807, -0.025153, -0.027074, -0.023513, -0.023727, -0.028669, -0.029153, -0.024831, -0.018735, -0.009246
	-0.056176, -0.059439, -0.066501, -0.071527, -0.085216, -0.094918, -0.097595, -0.099419, -0.101847, -0.102015, -0.093849, -0.089867, -0.088840, -0.083167, -0.071832, -0.062522, -0.058023, -0.057771, -0.053050, -0.048285, -0.041374, -0.033527, -0.024473, -0.018428, -0.013958, -0.008161, -0.001196, 0.001754, -0.004016, -0.011132, -0.018325, -0.021813, -0.021514, -0.016948, -0.018061, -0.025702, -0.028671, -0.021470, -0.011028, -0.001934
	-0.059202, -0.050525, -0.065461, -0.076792, -0.084156, -0.088538, -0.090719, -0.096070, -0.105729, -0.105136, -0.090350, -0.083865, -0.087807, -0.086145, -0.074773, -0.064235, -0.057641, -0.055896, -0.051286, -0.046566, -0.042431, -0.034723, -0.023762, -0.014983, -0.009126, -0.004877, 0.000094, 0.003492, -0.000931, -0.005883, -0.011665, -0.015251, -0.016432, -0.016119, -0.015373, -0.018827, -0.019994, -0.017564, -0.012298, 0.002094
	-0.055561, -0.058184, -0.062669, -0.068111, -0.080741, -0.091895, -0.093911, -0.094387, -0.100239, -0.100695, -0.089841, -0.085682, -0.085212, -0.082910, -0.073072, -0.063594, -0.056157, -0.053482, -0.048107, -0.045405, -0.039982, -0.029777, -0.019905, -0.013872, -0.009732, -0.004272, 0.003500, 0.006909, 0.001302, -0.004626, -0.012374, -0.014751, -0.014637, -0.011794, -0.012913, -0.018244, -0.023377, -0.018086, -0.006575, 0.003294
	-0.062834, -0.047300, -0.060870, -0.073023, -0.079303, -0.082121, -0.083623, -0.091321, -0.100996, -0.098896, -0.085406, -0.078881, -0.081932, -0.082077, -0.074409, -0.063158, -0.053822, -0.050328, -0.045077, -0.039678, -0.035825, -0.028532, -0.017793, -0.009121, -0.003444, -0.000905, 0.003990, 0.007745, 0.004595, 0.000143, -0.004555, -0.007411, -0.010850, -0.010100, -0.010079, -0.013177, -0.016434, -0.014663, -0.010248, -0.000213
	-0.054748, -0.053907, -0.057576, -0.063118, -0.072478, -0.081366, -0.084424, -0.086348, -0.089718, -0.089305, -0.081771, -0.076889, -0.076923, -0.073518, -0.067973, -0.057643, -0.050848, -0.046966, -0.041560, -0.036436, -0.029233, -0.020685, -0.010240, -0.004935, -0.001084, 0.002478, 0.009168, 0.014038, 0.010885, 0.004752, -0.001650, -0.004209, -0.003998, -0.002336, -0.003784, -0.010930, -0.016480, -0.012798, -0.003650, 0.002998
	-0.059345, -0.041989, -0.057435, -0.068229, -0.072857, -0.072586, -0.075155, -0.083286, -0.091292, -0.089727, -0.073702, -0.068353, -0.072910, -0.073863, -0.065527, -0.053635, -0.046064, -0.043899, -0.037607, -0.031251, -0.026194, -0.018885, -0.008095, 0.000309, 0.004911, 0.007046, 0.010642, 0.015635, 0.015277, 0.012612, 0.008074, 0.004852, 0.001546, 0.000504, 0.000589, -0.002769, -0.006432, -0.007765, -0.005391, 0.006950
	-0.050324, -0.049088, -0.052417, -0.057257, -0.063818, -0.071057, -0.074636, -0.075459, -0.079445, -0.077368, -0.068788, -0.063940, -0.065040, -0.063419, -0.054864, -0.044910, -0.038774, -0.036951, -0.031149, -0.026080, -0.018383, -0.011985, -0.001732, 0.003893, 0.007180, 0.011120, 0.017429, 0.021738, 0.019167, 0.015812, 0.011027, 0.007243, 0.006720, 0.009346, 0.006598, -0.003776, -0.009199, -0.007592, 0.005481, 0.014396
	-0.058437, -0.035937, -0.050762, -0.060425, -0.061123, -0.059090, -0.062399, -0.072124, -0.080338, -0.074950, -0.060985, -0.054754, -0.059333, -0.060500, -0.051714, -0.038834, -0.031117, -0.031693, -0.025186, -0.017982, -0.014316, -0.010137, 0.000228, 0.008774, 0.014018, 0.016470, 0.019918, 0.022071, 0.021109, 0.019957, 0.018698, 0.015803, 0.013135, 0.011136, 0.008719, 0.003522, -0.000994, 0.000525, 0.006297, 0.018454
	-0.046143, -0.041577, -0.045391, -0.046668, -0.051722, -0.057607, -0.062802, -0.065205, -0.068243, -0.066293, -0.058216, -0.051324, -0.051806, -0.051018, -0.043393, -0.032431, -0.024016, -0.023321, -0.018504, -0.013897, -0.008455, -0.001123, 0.006609, 0.010462, 0.013887, 0.019328, 0.024804, 0.026590, 0.023420, 0.020337, 0.017129, 0.017199, 0.016391, 0.015616, 0.013257, 0.005832, -0.000019, 0.003462, 0.014308, 0.023624
	-0.051989, -0.030294, -0.043380, -0.051339, -0.050711, -0.048193, -0.052258, -0.061218, -0.070507, -0.068810, -0.049476, -0.042352, -0.046018, -0.046673, -0.038670, -0.027263, -0.018137, -0.018587, -0.013603, -0.008482, -0.004647, -0.000011, 0.008230, 0.015652, 0.019436, 0.023069, 0.024762, 0.027750, 0.028115, 0.026227, 0.022220, 0.023166, 0.020341, 0.018455, 0.014918, 0.011932, 0.007138, 0.008523, 0.014718, 0.026201
	-0.041448, -0.035286, -0.036538, -0.037577, -0.044652, -0.049300, -0.051092, -0.052841, -0.058068, -0.056947, -0.046235, -0.038436, -0.037494, -0.034175, -0.028932, -0.016904, -0.010075, -0.010552, -0.004464, -0.001243, 0.003236, 0.010200, 0.015604, 0.020362, 0.023157, 0.028023, 0.032826, 0.035958, 0.034819, 0.030600, 0.025988, 0.026013, 0.026284, 0.025661, 0.022322, 0.013336, 0.006464, 0.011312, 0.022330, 0.031668
	-0.048540, -0.022534, -0.035260, -0.042156, -0.042749, -0.037408, -0.038818, -0.047322, -0.056808, -0.053643, -0.035691, -0.027822, -0.028789, -0.028255, -0.020274, -0.007285, -0.000723, -0.000788, 0.005440, 0.008938, 0.008953, 0.012074, 0.017957, 0.025241, 0.029175, 0.032057, 0.033733, 0.038359, 0.039349, 0.037161, 0.034052, 0.034585, 0.032020, 0.029940, 0.026326, 0.024577, 0.020432, 0.021586, 0.024568, 0.034552
	-0.033086, -0.027982, -0.029443, -0.029011, -0.035629, -0.040579, -0.038290, -0.037389, -0.041260, -0.040430, -0.032279, -0.021394, -0.018817, -0.015525, -0.007558, 0.006345, 0.011048, 0.011271, 0.013497, 0.017030, 0.017449, 0.022752, 0.026764, 0.030722, 0.033532, 0.037203, 0.043356, 0.048536, 0.047776, 0.043851, 0.039311, 0.039944, 0.039954, 0.038931, 0.034893, 0.030946, 0.023127, 0.027359, 0.034859, 0.043920
	-0.036218, -0.016846, -0.030897, -0.036980, -0.037261, -0.033334, -0.030888, -0.034074, -0.042142, -0.039980, -0.021377, -0.013603, -0.014171, -0.013131, -0.001768, 0.014998, 0.020060, 0.018173, 0.019934, 0.024704, 0.023739, 0.024617, 0.027288, 0.035116, 0.041187, 0.043128, 0.045921, 0.051709, 0.053031, 0.050698, 0.047697, 0.047728, 0.046845, 0.043201, 0.041805, 0.040728, 0.036184, 0.034435, 0.035120, 0.045329
	-0.029808, -0.023871, -0.026541, -0.026705, -0.031203, -0.036908, -0.034411, -0.029231, -0.028090, -0.026102, -0.016691, -0.007747, -0.004471, 0.001560, 0.010738, 0.025062, 0.027672, 0.024833, 0.026976, 0.029502, 0.030754, 0.035709, 0.039403, 0.044719, 0.046379, 0.049250, 0.054178, 0.059793, 0.059542, 0.052111, 0.047608, 0.050103, 0.053142, 0.052747, 0.050045, 0.044102, 0.033149, 0.035392, 0.045678, 0.054080
	-0.032238, -0.008993, -0.023999, -0.030969, -0.028658, -0.024887, -0.024493, -0.028088, -0.031053, -0.022849, -0.003868, 0.004647, 0.004540, 0.007560, 0.018373, 0.031401, 0.035778, 0.033768, 0.035173, 0.035884, 0.036597, 0.038940, 0.044566, 0.053914, 0.056554, 0.056382, 0.056449, 0.060387, 0.062696, 0.058223, 0.055016, 0.056193, 0.056891, 0.052793, 0.052741, 0.052626, 0.048117, 0.045032, 0.048033, 0.055100
	-0.019758, -0.015110, -0.017814, -0.018871, -0.023340, -0.028653, -0.026880, -0.018681, -0.017020, -0.011343, -0.001002, 0.008249, 0.014012, 0.020367, 0.026878, 0.038534, 0.041827, 0.039532, 0.039775, 0.039109, 0.043172, 0.049325, 0.056604, 0.059583, 0.059329, 0.059876, 0.062766, 0.068759, 0.067214, 0.059657, 0.055950, 0.056798, 0.058619, 0.058591, 0.059849, 0.056473, 0.046841, 0.047921, 0.058342, 0.065346
	-0.018628, -0.000296, -0.014764, -0.022634, -0.020483, -0.016362, -0.015485, -0.017352, -0.020246, -0.010362, 0.008635, 0.018414, 0.018542, 0.024258, 0.033370, 0.045728, 0.049983, 0.044610, 0.044638, 0.047649, 0.049220, 0.051954, 0.058932, 0.065915, 0.069102, 0.067410, 0.067680, 0.073734, 0.072203, 0.067293, 0.063945, 0.064378, 0.065047, 0.061989, 0.062882, 0.063468, 0.059707, 0.057986, 0.059739, 0.066139
	-0.010091, -0.006551, -0.008018, -0.009589, -0.016068, -0.020662, -0.019451, -0.010985, -0.009391, -0.003580, 0.007826, 0.019598, 0.024961, 0.033762, 0.040618, 0.050868, 0.052139, 0.050495, 0.049198, 0.051777, 0.056840, 0.061771, 0.068414, 0.072295, 0.073443, 0.072145, 0.073414, 0.079338, 0.075988, 0.067367, 0.064745, 0.064435, 0.066982, 0.065811, 0.067424, 0.063230, 0.058438, 0.059982, 0.067672, 0.072460
	-0.016254, 0.006291, -0.008031, -0.013944, -0.014475, -0.010741, -0.009932, -0.011709, -0.015503, -0.006971, 0.013190, 0.024865, 0.029121, 0.033942, 0.044335, 0.054572, 0.058078, 0.055224, 0.055897, 0.058327, 0.061207, 0.063939, 0.070506, 0.078141, 0.084203, 0.081223, 0.079519, 0.082883, 0.080890, 0.076174, 0.071279, 0.073064, 0.071225, 0.066859, 0.069860, 0.070836, 0.069427, 0.069140, 0.070950, 0.075269
	-0.008127, 0.000730, 0.001164, -0.000308, -0.006659, -0.012343, -0.011463, -0.003755, -0.001876, 0.005166, 0.016616, 0.030243, 0.036509, 0.045020, 0.053681, 0.063738, 0.066425, 0.063964, 0.062796, 0.065633, 0.071912, 0.077280, 0.082580, 0.086477, 0.089798, 0.089603, 0.091453, 0.096125, 0.088708, 0.079903, 0.074317, 0.076190, 0.075399, 0.075242, 0.079628, 0.077855, 0.071473, 0.073702, 0.082757, 0.088086
	-0.010951, 0.013218, -0.000878, -0.006241, -0.005623, 0.000046, 0.000158, -0.002943, -0.005314, 0.005491, 0.026890, 0.035754, 0.041490, 0.045829, 0.059325, 0.070249, 0.074114, 0.071815, 0.073229, 0.076313, 0.080778, 0.081554, 0.087919, 0.096206, 0.101562, 0.101674, 0.100494, 0.103989, 0.100292, 0.093977, 0.088080, 0.088136, 0.086555, 0.081494, 0.084966, 0.087073, 0.084113, 0.085184, 0.087700, 0.092188
	-0.002972, 0.006020, 0.006098, 0.004303, 0.001326, -0.002386, -0.001840, 0.005325, 0.008624, 0.016246, 0.026781, 0.039696, 0.048540, 0.055938, 0.066982, 0.076497, 0.080828, 0.079669, 0.080127, 0.083754, 0.089783, 0.093456, 0.100570, 0.105322, 0.107132, 0.110571, 0.113141, 0.118064, 0.111721, 0.101634, 0.093555, 0.093112, 0.093104, 0.092325, 0.094780, 0.092552, 0.085283, 0.088882, 0.097508, 0.105280
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 11.4
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Preperations]
version = 1
points = 
	0.012158, -0.006098, -0.020628, -0.034069, -0.049418, -0.058491, -0.062706, -0.063181, -0.065552, -0.063461, -0.057373, -0.056717, -0.056579, -0.054080, -0.053373, -0.056878, -0.057281, -0.055224, -0.049676, -0.047605, -0.041454, -0.034605, -0.022490, -0.011292, -0.009411, -0.005344, -0.003510, -0.002717, -0.005999, -0.010712, -0.013141, -0.015611, -0.020004, -0.017667, -0.016629, -0.022248, -0.024864, -0.024065, -0.014921, -0.010826
	-0.005958, -0.021084, -0.033800, -0.047903, -0.059950, -0.071345, -0.072502, -0.073350, -0.075852, -0.072963, -0.067236, -0.064315, -0.065698, -0.064338, -0.062871, -0.065238, -0.067095, -0.063584, -0.059241, -0.057846, -0.051380, -0.043157, -0.030230, -0.019950, -0.018121, -0.014291, -0.009354, -0.013065, -0.016464, -0.022925, -0.025337, -0.026541, -0.030577, -0.029068, -0.027094, -0.030532, -0.034241, -0.032625, -0.021498, -0.020513
	-0.017526, -0.027763, -0.040710, -0.055305, -0.068172, -0.079641, -0.081247, -0.081903, -0.083679, -0.081855, -0.073270, -0.070340, -0.072083, -0.071536, -0.066055, -0.065901, -0.069085, -0.066531, -0.063284, -0.061616, -0.053366, -0.047292, -0.035451, -0.023167, -0.022205, -0.016699, -0.012552, -0.014153, -0.018802, -0.030443, -0.032210, -0.034051, -0.034437, -0.031439, -0.030406, -0.032817, -0.036351, -0.034849, -0.024250, -0.019489
	-0.017750, -0.030284, -0.043463, -0.055839, -0.071865, -0.084888, -0.086157, -0.084619, -0.086681, -0.084515, -0.075246, -0.073263, -0.075604, -0.075123, -0.069177, -0.070723, -0.071097, -0.068644, -0.065465, -0.063718, -0.057574, -0.049335, -0.036556, -0.028418, -0.028259, -0.023387, -0.018454, -0.020519, -0.027499, -0.038314, -0.041534, -0.041886, -0.039972, -0.036438, -0.033959, -0.033009, -0.038291, -0.036339, -0.022688, -0.024783
	-0.021354, -0.034103, -0.047541, -0.060551, -0.075691, -0.089373, -0.092241, -0.091621, -0.093203, -0.090723, -0.082480, -0.079781, -0.079706, -0.079674, -0.074365, -0.073780, -0.073465, -0.070165, -0.064970, -0.065503, -0.059104, -0.051038, -0.041817, -0.031243, -0.031386, -0.028837, -0.023658, -0.024237, -0.029641, -0.039210, -0.042766, -0.044461, -0.041863, -0.039075, -0.034881, -0.034571, -0.039386, -0.038253, -0.031659, -0.024202
	-0.027696, -0.041184, -0.054054, -0.064759, -0.080898, -0.094964, -0.097906, -0.098033, -0.101256, -0.098300, -0.091517, -0.088420, -0.086945, -0.085220, -0.079938, -0.079979, -0.079828, -0.074842, -0.072903, -0.072415, -0.065384, -0.057454, -0.048482, -0.040977, -0.039336, -0.036065, -0.032553, -0.034336, -0.039337, -0.046271, -0.049398, -0.051220, -0.049530, -0.045000, -0.045029, -0.042100, -0.049767, -0.046386, -0.035574, -0.032188
	-0.033426, -0.046259, -0.059363, -0.068024, -0.084858, -0.097009, -0.103434, -0.106215, -0.107319, -0.106178, -0.100333, -0.097536, -0.095352, -0.091322, -0.086332, -0.082309, -0.081440, -0.078413, -0.075067, -0.073134, -0.068255, -0.062667, -0.054300, -0.046004, -0.042001, -0.039181, -0.035010, -0.036092, -0.041599, -0.048788, -0.051751, -0.051179, -0.051019, -0.049121, -0.045860, -0.046756, -0.050005, -0.051613, -0.040237, -0.035349
	-0.037931, -0.051993, -0.066455, -0.075044, -0.088177, -0.102890, -0.108223, -0.112373, -0.115787, -0.113421, -0.108543, -0.105936, -0.101048, -0.096863, -0.090726, -0.087882, -0.086665, -0.083874, -0.081096, -0.080894, -0.075125, -0.071038, -0.063072, -0.054696, -0.051039, -0.046728, -0.042566, -0.043887, -0.048745, -0.056834, -0.059808, -0.060521, -0.060664, -0.057968, -0.056317, -0.052477, -0.058814, -0.055877, -0.046325, -0.042545
	-0.041429, -0.053634, -0.067633, -0.077111, -0.090998, -0.103561, -0.109445, -0.114741, -0.120075, -0.119821, -0.114703, -0.110411, -0.105589, -0.099826, -0.093730, -0.089705, -0.087199, -0.086439, -0.082688, -0.082221, -0.078348, -0.073203, -0.065273, -0.058731, -0.054025, -0.049231, -0.044830, -0.043830, -0.045839, -0.054137, -0.059075, -0.059515, -0.058546, -0.056956, -0.054145, -0.053129, -0.056587, -0.056341, -0.047057, -0.039936
	-0.044295, -0.058972, -0.072101, -0.082726, -0.095001, -0.106449, -0.111505, -0.118363, -0.124608, -0.123506, -0.120263, -0.115400, -0.110227, -0.104535, -0.100348, -0.095757, -0.092961, -0.092377, -0.089613, -0.088047, -0.084834, -0.079314, -0.072500, -0.064519, -0.060449, -0.055767, -0.051803, -0.050997, -0.052855, -0.058115, -0.063348, -0.065363, -0.067936, -0.063474, -0.061475, -0.054726, -0.062529, -0.055352, -0.048878, -0.044991
	-0.045804, -0.056574, -0.073308, -0.082450, -0.097495, -0.107467, -0.111501, -0.116418, -0.126724, -0.125980, -0.123231, -0.120494, -0.114667, -0.111289, -0.103451, -0.099228, -0.095880, -0.095882, -0.093328, -0.091000, -0.087051, -0.081909, -0.075949, -0.064971, -0.061050, -0.055137, -0.049046, -0.047319, -0.049806, -0.056968, -0.059608, -0.060249, -0.063032, -0.060556, -0.056284, -0.056263, -0.058891, -0.057890, -0.051554, -0.042382
	-0.049818, -0.062681, -0.076305, -0.084328, -0.098717, -0.107866, -0.113937, -0.120088, -0.128622, -0.128931, -0.126353, -0.123191, -0.118529, -0.115642, -0.106288, -0.103976, -0.099708, -0.097750, -0.094501, -0.094545, -0.090910, -0.085952, -0.077352, -0.067196, -0.062435, -0.057738, -0.052934, -0.051098, -0.055294, -0.061112, -0.063120, -0.067525, -0.067979, -0.066558, -0.064608, -0.060597, -0.067812, -0.057641, -0.056224, -0.046471
	-0.050591, -0.060432, -0.075602, -0.083877, -0.096933, -0.106147, -0.112334, -0.118295, -0.127966, -0.128757, -0.125157, -0.121831, -0.118557, -0.116124, -0.108723, -0.104502, -0.099469, -0.095841, -0.090662, -0.089822, -0.087969, -0.084545, -0.076375, -0.064821, -0.059093, -0.053427, -0.047372, -0.044341, -0.047964, -0.054064, -0.057133, -0.059152, -0.061568, -0.059109, -0.056640, -0.056691, -0.056844, -0.054564, -0.048514, -0.040641
	-0.047704, -0.059564, -0.073127, -0.080945, -0.093764, -0.105483, -0.111501, -0.118792, -0.124812, -0.126576, -0.122064, -0.118087, -0.116126, -0.114867, -0.108053, -0.103336, -0.097558, -0.093250, -0.086537, -0.085303, -0.083677, -0.079292, -0.070542, -0.062526, -0.056818, -0.052534, -0.044035, -0.041353, -0.046942, -0.051329, -0.055481, -0.062777, -0.058499, -0.058025, -0.057390, -0.053562, -0.060843, -0.046555, -0.046260, -0.036083
	-0.046496, -0.052983, -0.067518, -0.076904, -0.091704, -0.103105, -0.111995, -0.117751, -0.122307, -0.122941, -0.118230, -0.115004, -0.114258, -0.113138, -0.105515, -0.098417, -0.093384, -0.090070, -0.083281, -0.079846, -0.078725, -0.075452, -0.066225, -0.057269, -0.053103, -0.047808, -0.039772, -0.036834, -0.041270, -0.047376, -0.051111, -0.053848, -0.053029, -0.050301, -0.048919, -0.050775, -0.050121, -0.046842, -0.039633, -0.030497
	-0.040695, -0.051685, -0.064038, -0.070974, -0.086679, -0.101773, -0.109889, -0.114373, -0.117883, -0.118764, -0.113125, -0.110931, -0.111099, -0.109664, -0.098733, -0.093182, -0.090154, -0.086213, -0.077214, -0.077108, -0.075555, -0.069117, -0.060704, -0.054093, -0.049253, -0.044799, -0.037536, -0.035304, -0.040134, -0.045456, -0.051720, -0.056675, -0.053743, -0.052923, -0.049701, -0.050238, -0.056776, -0.041485, -0.041755, -0.027329
	-0.039842, -0.039428, -0.055732, -0.063890, -0.079179, -0.092823, -0.101698, -0.106156, -0.111709, -0.113152, -0.108033, -0.104872, -0.105645, -0.103501, -0.094487, -0.087264, -0.084273, -0.080950, -0.074116, -0.070973, -0.068409, -0.062825, -0.054757, -0.044150, -0.040620, -0.036602, -0.031538, -0.026478, -0.031123, -0.037600, -0.042341, -0.046700, -0.047380, -0.042880, -0.040967, -0.045367, -0.044192, -0.038553, -0.029948, -0.020790
	-0.030596, -0.038279, -0.051528, -0.058981, -0.073983, -0.089044, -0.099173, -0.101740, -0.104830, -0.107083, -0.102306, -0.101554, -0.101336, -0.097146, -0.089217, -0.083800, -0.080621, -0.078071, -0.071535, -0.068328, -0.065806, -0.056882, -0.048683, -0.039756, -0.036349, -0.031328, -0.025351, -0.024133, -0.029773, -0.033858, -0.040011, -0.044146, -0.043900, -0.044797, -0.038019, -0.042319, -0.047297, -0.031851, -0.034318, -0.013527
	-0.032121, -0.034722, -0.047839, -0.054710, -0.069175, -0.084213, -0.094533, -0.097233, -0.100863, -0.104775, -0.099781, -0.097416, -0.098804, -0.096059, -0.086694, -0.079692, -0.076749, -0.074609, -0.068106, -0.063906, -0.061136, -0.055447, -0.045559, -0.035389, -0.029696, -0.025708, -0.020034, -0.017335, -0.022665, -0.028532, -0.032369, -0.035760, -0.037212, -0.035201, -0.032872, -0.034132, -0.035907, -0.032127, -0.025026, -0.009282
	-0.026707, -0.034374, -0.045183, -0.052691, -0.067014, -0.084964, -0.092286, -0.094441, -0.099291, -0.103609, -0.098278, -0.094972, -0.097169, -0.095394, -0.086653, -0.080205, -0.076284, -0.070594, -0.064535, -0.062012, -0.060174, -0.051216, -0.040622, -0.033396, -0.029636, -0.024235, -0.017274, -0.018232, -0.021459, -0.024778, -0.031754, -0.034481, -0.033398, -0.037949, -0.030432, -0.033219, -0.038432, -0.021975, -0.030052, -0.009295
	-0.028559, -0.029280, -0.042071, -0.048655, -0.061603, -0.076257, -0.086817, -0.091815, -0.095682, -0.098682, -0.093729, -0.091168, -0.092213, -0.090073, -0.084070, -0.077048, -0.072045, -0.066267, -0.060309, -0.053639, -0.051696, -0.046852, -0.034069, -0.025602, -0.020640, -0.018021, -0.013180, -0.009049, -0.013846, -0.018012, -0.021061, -0.024515, -0.027068, -0.026804, -0.024283, -0.025595, -0.028234, -0.025272, -0.019246, -0.008595
	-0.025711, -0.029003, -0.038836, -0.048015, -0.058511, -0.074480, -0.083738, -0.087945, -0.091439, -0.094310, -0.090288, -0.087858, -0.088589, -0.086163, -0.081829, -0.075146, -0.071136, -0.064399, -0.057338, -0.052103, -0.049650, -0.043210, -0.032998, -0.023124, -0.020191, -0.016625, -0.012433, -0.010465, -0.009871, -0.015007, -0.021217, -0.021582, -0.023800, -0.027652, -0.021527, -0.027137, -0.030828, -0.020152, -0.026202, -0.008568
	-0.031287, -0.022523, -0.035800, -0.041583, -0.052691, -0.065901, -0.075941, -0.079246, -0.083936, -0.086778, -0.082235, -0.078893, -0.080642, -0.079419, -0.074324, -0.067418, -0.062113, -0.057744, -0.049923, -0.043390, -0.040055, -0.035512, -0.023838, -0.015485, -0.009895, -0.008346, -0.005387, 0.001467, -0.000104, -0.003777, -0.007926, -0.012023, -0.013970, -0.014207, -0.013994, -0.017009, -0.019233, -0.019282, -0.014210, -0.001146
	-0.020719, -0.024043, -0.035160, -0.041635, -0.051902, -0.063884, -0.072884, -0.076738, -0.081856, -0.083761, -0.077857, -0.074651, -0.077952, -0.076310, -0.069721, -0.063240, -0.056775, -0.055188, -0.046711, -0.042996, -0.039499, -0.032268, -0.023129, -0.015735, -0.012305, -0.009383, -0.005789, -0.001996, -0.001166, -0.005106, -0.009634, -0.009864, -0.011905, -0.015913, -0.010246, -0.016645, -0.022975, -0.011972, -0.018524, 0.001048
	-0.026050, -0.019774, -0.032555, -0.037813, -0.044657, -0.054435, -0.065271, -0.071019, -0.075585, -0.077479, -0.072635, -0.069526, -0.071046, -0.070770, -0.063085, -0.055960, -0.050956, -0.049593, -0.042773, -0.034996, -0.032645, -0.029030, -0.020343, -0.011008, -0.005751, -0.003252, 0.000746, 0.003215, 0.001749, -0.000068, -0.001413, -0.002608, -0.005837, -0.007103, -0.008431, -0.012027, -0.015656, -0.014417, -0.006321, 0.003748
	-0.021728, -0.019178, -0.031232, -0.036249, -0.042206, -0.053190, -0.064017, -0.068545, -0.074597, -0.074544, -0.069543, -0.065779, -0.067928, -0.067354, -0.060655, -0.052790, -0.047723, -0.046044, -0.038188, -0.034539, -0.032080, -0.027152, -0.018902, -0.012508, -0.009304, -0.003955, -0.000288, -0.001549, -0.000556, -0.003756, -0.008467, -0.003851, -0.005999, -0.012959, -0.007423, -0.015332, -0.017388, -0.005695, -0.010807, 0.007710
	-0.028204, -0.017096, -0.027984, -0.032129, -0.038374, -0.046561, -0.059356, -0.061847, -0.069228, -0.070551, -0.065474, -0.059719, -0.059893, -0.060271, -0.053666, -0.047202, -0.041189, -0.039979, -0.033189, -0.028761, -0.025714, -0.021660, -0.014905, -0.007841, -0.004669, -0.001174, 0.001874, 0.005613, 0.005527, 0.001504, -0.000694, 0.001892, 0.001885, -0.002506, -0.005619, -0.007166, -0.009935, -0.007406, 0.000545, 0.009983
	-0.019393, -0.017785, -0.025482, -0.028146, -0.036861, -0.047528, -0.055696, -0.059118, -0.064151, -0.066346, -0.060565, -0.055661, -0.055495, -0.051944, -0.048147, -0.040645, -0.036359, -0.035990, -0.026764, -0.024843, -0.023572, -0.019648, -0.013807, -0.006811, -0.004589, -0.000266, 0.003010, 0.004931, 0.006834, 0.003254, -0.001690, 0.003120, 0.001036, -0.005283, 0.000659, -0.007399, -0.010996, -0.000832, -0.006381, 0.012135
	-0.021519, -0.010062, -0.018662, -0.023011, -0.029067, -0.036961, -0.043194, -0.048197, -0.053632, -0.055489, -0.050054, -0.045247, -0.042655, -0.040243, -0.034315, -0.027094, -0.022697, -0.021644, -0.015333, -0.010768, -0.013712, -0.012051, -0.005326, 0.000560, 0.005300, 0.007429, 0.009930, 0.015968, 0.016454, 0.012383, 0.010385, 0.011612, 0.011413, 0.008357, 0.006831, 0.005524, 0.003087, 0.003507, 0.009876, 0.018892
	-0.017331, -0.015238, -0.021971, -0.024651, -0.029507, -0.040209, -0.044232, -0.046101, -0.052689, -0.053151, -0.047133, -0.042985, -0.040475, -0.037020, -0.029999, -0.021348, -0.018232, -0.017876, -0.013058, -0.008535, -0.013279, -0.011527, -0.006296, -0.001615, 0.002270, 0.006991, 0.010272, 0.013407, 0.015950, 0.012503, 0.008026, 0.013701, 0.011513, 0.004867, 0.010667, 0.006774, 0.003571, 0.012416, 0.004875, 0.020961
	-0.022637, -0.011107, -0.018340, -0.023896, -0.028320, -0.038092, -0.041212, -0.041642, -0.044537, -0.046015, -0.041699, -0.035805, -0.033527, -0.030911, -0.022925, -0.010175, -0.007279, -0.008644, -0.005065, -0.000597, -0.003797, -0.004052, 0.000635, 0.006175, 0.010857, 0.012993, 0.016956, 0.022765, 0.023298, 0.020262, 0.018285, 0.019467, 0.021161, 0.018785, 0.017891, 0.017817, 0.013874, 0.012825, 0.015904, 0.025844
	-0.014532, -0.010189, -0.019385, -0.022584, -0.028159, -0.037803, -0.040566, -0.038125, -0.040339, -0.038899, -0.033171, -0.028143, -0.025641, -0.019755, -0.012463, -0.003824, -0.000871, -0.002698, -0.000197, 0.001952, -0.001353, -0.000188, 0.004902, 0.012600, 0.014373, 0.016449, 0.018872, 0.022822, 0.026385, 0.020681, 0.015275, 0.021387, 0.023535, 0.016733, 0.022161, 0.018819, 0.011276, 0.020785, 0.014683, 0.032409
	-0.016972, -0.004835, -0.015539, -0.019706, -0.022971, -0.032222, -0.037732, -0.035551, -0.033892, -0.031679, -0.024624, -0.019946, -0.016412, -0.010040, -0.003445, 0.005991, 0.008364, 0.006410, 0.008289, 0.009260, 0.007409, 0.008691, 0.015230, 0.022729, 0.025465, 0.025502, 0.026102, 0.030309, 0.031861, 0.026963, 0.024651, 0.027000, 0.029039, 0.025577, 0.027217, 0.027660, 0.023245, 0.021705, 0.026383, 0.034120
	-0.007042, -0.003943, -0.013314, -0.016082, -0.020497, -0.030911, -0.035096, -0.030889, -0.029351, -0.025337, -0.018980, -0.012449, -0.008879, -0.001902, 0.003577, 0.011256, 0.012460, 0.010502, 0.011904, 0.011483, 0.010067, 0.013356, 0.020792, 0.027368, 0.026382, 0.028554, 0.028164, 0.029993, 0.033232, 0.028830, 0.022354, 0.027991, 0.029607, 0.020011, 0.031066, 0.031755, 0.025061, 0.037228, 0.024607, 0.041453
	-0.012463, -0.000987, -0.008994, -0.014815, -0.017487, -0.026372, -0.031392, -0.028459, -0.025402, -0.024153, -0.015566, -0.007862, -0.004579, 0.001484, 0.010757, 0.017401, 0.019536, 0.016264, 0.016278, 0.018231, 0.018193, 0.018217, 0.025442, 0.034794, 0.036179, 0.034770, 0.033985, 0.040104, 0.040404, 0.034161, 0.030977, 0.032380, 0.034144, 0.031909, 0.033231, 0.035957, 0.034171, 0.033050, 0.038776, 0.042972
	-0.002758, 0.000700, -0.008467, -0.011525, -0.018705, -0.027522, -0.031609, -0.027494, -0.026315, -0.023221, -0.014164, -0.006562, -0.002205, 0.006453, 0.013689, 0.018647, 0.017673, 0.016751, 0.017380, 0.018782, 0.019038, 0.021992, 0.027475, 0.034748, 0.036870, 0.036635, 0.035394, 0.037519, 0.038008, 0.032063, 0.025834, 0.030409, 0.033142, 0.023991, 0.034882, 0.034323, 0.030317, 0.042711, 0.030793, 0.045129
	-0.011501, 0.004979, -0.003199, -0.009532, -0.013737, -0.022490, -0.028056, -0.025047, -0.023987, -0.021727, -0.011113, -0.003633, 0.003070, 0.010580, 0.020230, 0.025058, 0.026653, 0.024592, 0.024567, 0.025613, 0.027386, 0.029282, 0.037705, 0.042901, 0.046601, 0.045443, 0.044217, 0.048155, 0.045715, 0.039788, 0.034981, 0.038594, 0.038594, 0.034532, 0.038671, 0.042065, 0.040659, 0.042101, 0.045919, 0.050030
	-0.005239, 0.006624, -0.001837, -0.005350, -0.012024, -0.022230, -0.026144, -0.022704, -0.021559, -0.017450, -0.008515, 0.000433, 0.007392, 0.014546, 0.023538, 0.029043, 0.029892, 0.027280, 0.028785, 0.030662, 0.032758, 0.032649, 0.040035, 0.046372, 0.048654, 0.050330, 0.049538, 0.049746, 0.048851, 0.041068, 0.034598, 0.041375, 0.041379, 0.030621, 0.043091, 0.044712, 0.038634, 0.053475, 0.042814, 0.059369
	-0.011843, 0.005417, 0.000007, -0.005709, -0.011391, -0.019100, -0.024151, -0.021274, -0.019356, -0.016953, -0.004422, 0.002891, 0.010688, 0.018353, 0.027665, 0.035281, 0.036655, 0.034937, 0.036795, 0.039994, 0.042705, 0.042668, 0.048600, 0.055673, 0.059602, 0.061002, 0.059934, 0.064283, 0.061835, 0.052838, 0.048644, 0.048401, 0.048158, 0.044262, 0.049173, 0.053313, 0.050054, 0.051718, 0.058112, 0.062677
	-0.003249, 0.007140, -0.000190, -0.005182, -0.010664, -0.017472, -0.021072, -0.018928, -0.015929, -0.011810, -0.001170, 0.006999, 0.014346, 0.022026, 0.033087, 0.037703, 0.039304, 0.038986, 0.040531, 0.042739, 0.044912, 0.045850, 0.052980, 0.060894, 0.062495, 0.065477, 0.066306, 0.069035, 0.066301, 0.058359, 0.048879, 0.054660, 0.053906, 0.042834, 0.051292, 0.054304, 0.049390, 0.064968, 0.053062, 0.067337
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 80.0
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Peperations]
version = 1
points = 
	0.022498, 0.020830, 0.014175, -0.000111, -0.007965, -0.011932, -0.009252, -0.003320, -0.000118, 0.004151, 0.015991, 0.024593, 0.030148, 0.034696, 0.042241, 0.043592, 0.045307, 0.051419, 0.057700, 0.066468, 0.072764, 0.085492, 0.100446, 0.113063, 0.118900, 0.122870, 0.130290, 0.129755, 0.129462, 0.124089, 0.122420, 0.123461, 0.116841, 0.117893, 0.119241, 0.115227, 0.110631, 0.109920, 0.117187, 0.124332
	0.004953, 0.000716, -0.005511, -0.010742, -0.018400, -0.024021, -0.019665, -0.013525, -0.009878, -0.004126, 0.008939, 0.016408, 0.019292, 0.023840, 0.033007, 0.033600, 0.034448, 0.041047, 0.049029, 0.052882, 0.062512, 0.072410, 0.089182, 0.103027, 0.106205, 0.110789, 0.117912, 0.115269, 0.112784, 0.106051, 0.103603, 0.104209, 0.099603, 0.105100, 0.101466, 0.099610, 0.095780, 0.096420, 0.108661, 0.108286
	-0.007933, -0.002801, -0.011350, -0.022484, -0.029473, -0.033231, -0.030354, -0.021826, -0.018408, -0.013209, 0.001640, 0.008984, 0.012027, 0.014149, 0.024334, 0.028649, 0.030597, 0.034667, 0.041223, 0.046241, 0.051968, 0.062511, 0.079099, 0.090699, 0.097837, 0.101667, 0.108218, 0.106595, 0.104490, 0.095444, 0.089512, 0.089259, 0.089179, 0.091741, 0.094161, 0.094254, 0.091002, 0.088753, 0.095405, 0.102343
	-0.010759, -0.012564, -0.018170, -0.023960, -0.033106, -0.040910, -0.038354, -0.031441, -0.026122, -0.019953, -0.006267, 0.000733, 0.002678, 0.006102, 0.015437, 0.019860, 0.022689, 0.029563, 0.035629, 0.037302, 0.045089, 0.055137, 0.070820, 0.082978, 0.087158, 0.088614, 0.094487, 0.093851, 0.091038, 0.080923, 0.074433, 0.073797, 0.073058, 0.081788, 0.080734, 0.083111, 0.078149, 0.079373, 0.091335, 0.087853
	-0.027313, -0.019238, -0.027920, -0.036645, -0.043223, -0.049872, -0.048503, -0.043853, -0.040737, -0.035179, -0.021622, -0.013493, -0.010171, -0.007317, 0.001347, 0.007440, 0.011360, 0.015985, 0.023916, 0.026329, 0.031680, 0.042865, 0.056754, 0.067621, 0.072919, 0.075964, 0.080156, 0.081233, 0.077771, 0.068443, 0.063939, 0.062251, 0.063828, 0.065094, 0.069498, 0.071735, 0.067423, 0.064065, 0.069162, 0.076272
	-0.033298, -0.035618, -0.039940, -0.043358, -0.050731, -0.061413, -0.060545, -0.055944, -0.052261, -0.045471, -0.035624, -0.027633, -0.021472, -0.017300, -0.006949, -0.002776, -0.000154, 0.006413, 0.012882, 0.014721, 0.023411, 0.031711, 0.040565, 0.054702, 0.058761, 0.061734, 0.065369, 0.066037, 0.061059, 0.053849, 0.049600, 0.048373, 0.049189, 0.054631, 0.050470, 0.056349, 0.047074, 0.049651, 0.057444, 0.057485
	-0.046284, -0.039039, -0.049010, -0.054961, -0.061001, -0.068408, -0.069602, -0.066474, -0.063117, -0.059357, -0.049570, -0.041166, -0.035441, -0.029269, -0.019658, -0.012395, -0.008906, -0.005538, 0.002012, 0.008339, 0.013216, 0.018793, 0.031185, 0.040165, 0.047175, 0.050605, 0.054283, 0.054442, 0.049166, 0.043483, 0.039000, 0.040758, 0.040857, 0.040759, 0.042263, 0.043438, 0.040051, 0.035886, 0.041332, 0.048851
	-0.049893, -0.051919, -0.058103, -0.060142, -0.067656, -0.077159, -0.079195, -0.078019, -0.075421, -0.069471, -0.060409, -0.054194, -0.044226, -0.037275, -0.027912, -0.020020, -0.016789, -0.012491, -0.003457, 0.001129, 0.004540, 0.009435, 0.018232, 0.027941, 0.035138, 0.038227, 0.042656, 0.044103, 0.038517, 0.032121, 0.029666, 0.027319, 0.029774, 0.031572, 0.028887, 0.034828, 0.023795, 0.030023, 0.033606, 0.036047
	-0.061015, -0.055279, -0.067497, -0.072234, -0.078637, -0.083600, -0.085954, -0.087271, -0.088647, -0.083447, -0.073398, -0.065920, -0.058009, -0.048810, -0.040714, -0.032533, -0.027328, -0.020402, -0.011382, -0.006547, -0.005452, -0.002712, 0.004649, 0.014201, 0.021442, 0.025510, 0.032890, 0.034711, 0.030965, 0.026329, 0.018828, 0.019246, 0.018861, 0.019611, 0.020596, 0.021396, 0.020172, 0.015723, 0.020537, 0.029677
	-0.063777, -0.066149, -0.073750, -0.076131, -0.084016, -0.091900, -0.093741, -0.094496, -0.094840, -0.089548, -0.084332, -0.077263, -0.068485, -0.061963, -0.051082, -0.043658, -0.037912, -0.032323, -0.024324, -0.019914, -0.018261, -0.013727, -0.003485, 0.004316, 0.011418, 0.017023, 0.022980, 0.024505, 0.018896, 0.014000, 0.009498, 0.006074, 0.009480, 0.007611, 0.008958, 0.010086, -0.000341, 0.010423, 0.010467, 0.016794
	-0.072341, -0.064233, -0.079217, -0.084483, -0.091050, -0.094481, -0.095378, -0.096667, -0.100564, -0.098313, -0.093254, -0.086700, -0.079209, -0.071795, -0.061313, -0.051911, -0.046317, -0.042643, -0.037228, -0.031598, -0.027431, -0.020480, -0.012883, -0.003114, 0.004746, 0.010189, 0.015911, 0.017106, 0.014037, 0.008693, 0.005120, 0.003652, -0.000532, -0.001097, 0.001984, 0.000397, -0.002089, -0.002821, 0.000529, 0.009043
	-0.068927, -0.075835, -0.083530, -0.085213, -0.091299, -0.100015, -0.101020, -0.100921, -0.103349, -0.102493, -0.098069, -0.091292, -0.083452, -0.079672, -0.069612, -0.062472, -0.055862, -0.052233, -0.046746, -0.041991, -0.035219, -0.028225, -0.018698, -0.007309, -0.002458, 0.002051, 0.006595, 0.008468, 0.005218, -0.000205, -0.003131, -0.003647, -0.006151, -0.009154, -0.005539, -0.006971, -0.015297, -0.002874, -0.005242, 0.003706
	-0.070116, -0.067835, -0.086390, -0.089881, -0.095167, -0.099194, -0.100751, -0.103794, -0.106996, -0.105835, -0.098564, -0.092154, -0.085579, -0.083053, -0.074722, -0.066442, -0.059302, -0.053429, -0.047800, -0.042952, -0.039132, -0.034614, -0.025732, -0.012689, -0.005906, 0.001101, 0.006644, 0.010980, 0.007742, 0.002526, -0.000261, -0.004094, -0.008771, -0.008465, -0.007095, -0.008952, -0.010405, -0.010446, -0.006121, 0.002024
	-0.064366, -0.071780, -0.082938, -0.085702, -0.093522, -0.099237, -0.104020, -0.105939, -0.106226, -0.104298, -0.097541, -0.091253, -0.084969, -0.082450, -0.075561, -0.066547, -0.056511, -0.051248, -0.041287, -0.037794, -0.035633, -0.028059, -0.019518, -0.010556, -0.003388, 0.002054, 0.009492, 0.011478, 0.008555, 0.004735, -0.000781, -0.006427, -0.005697, -0.010270, -0.006112, -0.011704, -0.018717, -0.002750, -0.010971, 0.000116
	-0.076795, -0.064801, -0.080209, -0.085175, -0.093457, -0.101077, -0.104981, -0.106367, -0.106821, -0.105708, -0.098545, -0.090759, -0.086929, -0.083491, -0.074306, -0.064805, -0.055933, -0.049959, -0.042853, -0.036270, -0.034463, -0.029587, -0.018780, -0.010103, -0.003533, 0.001632, 0.007909, 0.014370, 0.009281, 0.004666, -0.002974, -0.007301, -0.010185, -0.008299, -0.006340, -0.009678, -0.011333, -0.010684, -0.006289, 0.002763
	-0.067470, -0.065770, -0.074038, -0.076420, -0.085702, -0.098704, -0.101940, -0.102629, -0.101903, -0.100342, -0.093820, -0.086941, -0.083804, -0.081020, -0.067700, -0.059395, -0.054055, -0.047911, -0.039687, -0.035672, -0.032029, -0.025979, -0.017057, -0.006973, -0.001656, 0.002001, 0.007249, 0.012112, 0.006541, 0.000572, -0.006284, -0.010415, -0.012279, -0.015087, -0.007848, -0.016491, -0.019704, -0.005357, -0.013151, 0.002966
	-0.074820, -0.054794, -0.069710, -0.075127, -0.082743, -0.091434, -0.095621, -0.097541, -0.099098, -0.097422, -0.089851, -0.083594, -0.081112, -0.078942, -0.066391, -0.057457, -0.050942, -0.048077, -0.041211, -0.034391, -0.030091, -0.026047, -0.014207, -0.005090, 0.000912, 0.005316, 0.010043, 0.015509, 0.011199, 0.004513, -0.001027, -0.006694, -0.011239, -0.011162, -0.009134, -0.013596, -0.014031, -0.011306, -0.007627, 0.001767
	-0.061695, -0.056074, -0.065188, -0.067950, -0.076218, -0.088303, -0.093436, -0.092999, -0.090937, -0.090555, -0.084407, -0.080354, -0.078692, -0.074308, -0.062767, -0.052729, -0.047475, -0.043949, -0.036669, -0.031720, -0.027940, -0.020058, -0.010125, -0.000940, 0.003512, 0.007720, 0.011869, 0.015296, 0.011180, 0.003886, -0.003309, -0.003380, -0.007926, -0.011633, -0.003540, -0.014182, -0.013975, -0.003720, -0.011797, 0.006338
	-0.070864, -0.046187, -0.061128, -0.065717, -0.072715, -0.083470, -0.088292, -0.087558, -0.087628, -0.089378, -0.083768, -0.077237, -0.077063, -0.071978, -0.061635, -0.052022, -0.046913, -0.041194, -0.034314, -0.028661, -0.027048, -0.021438, -0.009769, -0.001205, 0.004637, 0.008928, 0.013264, 0.017277, 0.013442, 0.007295, 0.003623, -0.002524, -0.004256, -0.005789, -0.004213, -0.007305, -0.010487, -0.010885, -0.006086, 0.007386
	-0.059345, -0.049207, -0.056858, -0.060052, -0.066579, -0.080604, -0.086910, -0.085647, -0.085267, -0.087618, -0.081260, -0.075368, -0.073937, -0.069758, -0.058235, -0.051634, -0.045288, -0.038732, -0.032262, -0.027928, -0.024928, -0.019266, -0.007996, 0.000923, 0.005834, 0.008336, 0.013557, 0.017068, 0.012350, 0.006475, 0.000982, 0.001103, -0.006223, -0.006853, -0.000966, -0.013148, -0.013975, -0.006310, -0.011605, 0.006165
	-0.066591, -0.039715, -0.053663, -0.059514, -0.065911, -0.075018, -0.080214, -0.082968, -0.083447, -0.085380, -0.079055, -0.071985, -0.070247, -0.065856, -0.057767, -0.049975, -0.044481, -0.039103, -0.031217, -0.024927, -0.020997, -0.016440, -0.004831, 0.004061, 0.009463, 0.011160, 0.014777, 0.020638, 0.017816, 0.011360, 0.006171, 0.002164, -0.002119, -0.003117, -0.003031, -0.005156, -0.011400, -0.011762, -0.009295, -0.000001
	-0.060314, -0.046160, -0.052794, -0.054967, -0.062049, -0.074106, -0.080446, -0.081200, -0.080809, -0.080477, -0.076170, -0.070932, -0.069101, -0.063634, -0.055720, -0.049501, -0.044939, -0.040131, -0.032438, -0.022882, -0.017627, -0.012524, -0.001324, 0.006685, 0.011868, 0.013658, 0.016095, 0.021837, 0.020158, 0.012528, 0.006089, 0.005453, -0.000976, -0.002140, 0.001104, -0.010111, -0.010612, -0.007452, -0.014357, 0.001011
	-0.075633, -0.036609, -0.049346, -0.055490, -0.059336, -0.067616, -0.073859, -0.075613, -0.076372, -0.078009, -0.070627, -0.064206, -0.064430, -0.061999, -0.054551, -0.047386, -0.040817, -0.037398, -0.028062, -0.018505, -0.012195, -0.007531, 0.001481, 0.011790, 0.019955, 0.022349, 0.022131, 0.024492, 0.023359, 0.019186, 0.014655, 0.008357, 0.004176, 0.002971, 0.002955, -0.000237, -0.005884, -0.010152, -0.009506, 0.002811
	-0.059008, -0.039658, -0.046978, -0.048324, -0.052285, -0.063338, -0.069082, -0.070556, -0.070625, -0.070049, -0.064460, -0.057403, -0.056723, -0.052882, -0.046968, -0.041507, -0.033211, -0.029974, -0.022900, -0.013579, -0.008803, -0.004962, 0.005653, 0.017026, 0.028171, 0.028651, 0.024731, 0.026850, 0.023371, 0.017073, 0.015171, 0.016616, 0.005521, 0.005756, 0.007586, -0.005103, -0.006856, -0.005604, -0.006599, 0.007528
	-0.068330, -0.030233, -0.043154, -0.047439, -0.047149, -0.051149, -0.060971, -0.063014, -0.065775, -0.064636, -0.058200, -0.050987, -0.050925, -0.050115, -0.041299, -0.033907, -0.026306, -0.024199, -0.017123, -0.009196, -0.006314, -0.003809, 0.004760, 0.015324, 0.026665, 0.029649, 0.028724, 0.027131, 0.025150, 0.021808, 0.019981, 0.016766, 0.012347, 0.008776, 0.005760, -0.000224, -0.004294, -0.005879, -0.002457, 0.010054
	-0.053519, -0.031388, -0.038255, -0.037590, -0.039245, -0.046335, -0.056314, -0.057830, -0.060291, -0.058967, -0.051413, -0.045449, -0.043947, -0.042018, -0.034113, -0.025887, -0.019539, -0.017727, -0.012711, -0.005860, -0.003102, 0.000774, 0.009438, 0.015884, 0.022961, 0.024229, 0.026012, 0.029407, 0.026717, 0.020406, 0.017796, 0.020289, 0.012243, 0.009711, 0.009234, -0.005990, -0.001013, 0.000740, -0.002144, 0.013012
	-0.068972, -0.023416, -0.032912, -0.036134, -0.035915, -0.040435, -0.047452, -0.051460, -0.055021, -0.055776, -0.048697, -0.039554, -0.036785, -0.035561, -0.029056, -0.021075, -0.013416, -0.012134, -0.007237, -0.000622, 0.001662, 0.005393, 0.012038, 0.019764, 0.023514, 0.026252, 0.028191, 0.031400, 0.031365, 0.027993, 0.023275, 0.021009, 0.018930, 0.014093, 0.009022, 0.004773, 0.002094, 0.001348, 0.005643, 0.015078
	-0.050527, -0.022437, -0.028090, -0.026206, -0.028387, -0.036911, -0.041310, -0.044227, -0.046970, -0.046769, -0.038081, -0.031386, -0.029516, -0.024050, -0.019435, -0.012381, -0.005732, -0.004173, 0.000911, 0.006849, 0.007360, 0.010699, 0.017436, 0.023369, 0.028527, 0.029640, 0.031002, 0.034727, 0.036582, 0.030763, 0.026015, 0.028623, 0.020834, 0.016185, 0.016933, 0.002829, 0.004984, 0.009818, 0.008874, 0.020032
	-0.067395, -0.010220, -0.021024, -0.024567, -0.024087, -0.029620, -0.032317, -0.034341, -0.038392, -0.038789, -0.030285, -0.021590, -0.017175, -0.014435, -0.007732, -0.000529, 0.005605, 0.007078, 0.012454, 0.017758, 0.016774, 0.015574, 0.020748, 0.028369, 0.033644, 0.034771, 0.036537, 0.040293, 0.042118, 0.039979, 0.035655, 0.033354, 0.030928, 0.024890, 0.021491, 0.018938, 0.013668, 0.012501, 0.017108, 0.023515
	-0.038833, -0.012802, -0.018564, -0.017459, -0.019062, -0.027068, -0.030119, -0.028336, -0.029665, -0.030695, -0.022239, -0.013522, -0.008358, -0.004785, 0.000463, 0.010662, 0.015564, 0.016950, 0.020281, 0.025300, 0.022680, 0.022717, 0.026679, 0.031617, 0.035801, 0.037098, 0.041294, 0.045640, 0.047879, 0.042000, 0.038044, 0.040629, 0.033892, 0.031247, 0.031584, 0.018500, 0.020116, 0.019823, 0.016638, 0.029979
	-0.054356, -0.002258, -0.012712, -0.017288, -0.016713, -0.022907, -0.024293, -0.021563, -0.022620, -0.021953, -0.015330, -0.005386, -0.000764, 0.002640, 0.009997, 0.022869, 0.028174, 0.027730, 0.030977, 0.035707, 0.032818, 0.030889, 0.033638, 0.038561, 0.044265, 0.045141, 0.047683, 0.051815, 0.054004, 0.050991, 0.045574, 0.043899, 0.044055, 0.039092, 0.035909, 0.032091, 0.026891, 0.022169, 0.024865, 0.030848
	-0.031827, -0.000102, -0.006368, -0.006487, -0.006247, -0.014001, -0.017110, -0.013043, -0.010851, -0.008764, -0.000213, 0.006477, 0.011144, 0.018309, 0.024745, 0.033643, 0.038648, 0.039249, 0.041148, 0.045266, 0.041693, 0.040999, 0.045484, 0.052613, 0.057066, 0.054753, 0.055112, 0.059287, 0.060203, 0.052465, 0.047993, 0.050999, 0.047464, 0.046460, 0.044507, 0.031433, 0.032267, 0.032025, 0.029852, 0.040329
	-0.053848, 0.008122, -0.005187, -0.009032, -0.006543, -0.010012, -0.013005, -0.011663, -0.008957, -0.004668, 0.005458, 0.012800, 0.016893, 0.023554, 0.031737, 0.038741, 0.043870, 0.043337, 0.046621, 0.047581, 0.045654, 0.044827, 0.050363, 0.058747, 0.061023, 0.060485, 0.059059, 0.061821, 0.061391, 0.055971, 0.051067, 0.050038, 0.051018, 0.046533, 0.043334, 0.042562, 0.036118, 0.029798, 0.032773, 0.039524
	-0.025830, 0.006164, -0.000655, 0.000164, 0.000088, -0.008033, -0.011008, -0.006017, -0.001301, 0.004088, 0.011848, 0.020276, 0.024465, 0.033383, 0.039126, 0.044268, 0.047916, 0.047402, 0.050050, 0.050456, 0.048891, 0.051771, 0.058154, 0.063246, 0.065463, 0.063072, 0.060950, 0.065351, 0.064614, 0.057455, 0.051194, 0.055723, 0.050906, 0.046407, 0.048283, 0.036561, 0.037400, 0.036887, 0.031589, 0.046759
	-0.041184, 0.017683, 0.006408, 0.000358, 0.001923, -0.002498, -0.003907, -0.001746, 0.001864, 0.006784, 0.017297, 0.026916, 0.030940, 0.036439, 0.045987, 0.050809, 0.054636, 0.052055, 0.053180, 0.056698, 0.057069, 0.055779, 0.063193, 0.067815, 0.071856, 0.070651, 0.067674, 0.070718, 0.070797, 0.062598, 0.057842, 0.056835, 0.056713, 0.051260, 0.048727, 0.048227, 0.044844, 0.039559, 0.041218, 0.044920
	-0.014008, 0.018619, 0.011274, 0.010878, 0.008771, 0.001246, -0.001819, 0.003600, 0.008052, 0.011983, 0.021970, 0.030757, 0.037662, 0.045972, 0.053195, 0.057661, 0.059206, 0.058383, 0.060240, 0.061039, 0.062504, 0.064497, 0.070278, 0.077704, 0.080246, 0.077015, 0.072985, 0.075685, 0.072584, 0.063534, 0.057732, 0.061938, 0.057545, 0.050931, 0.054863, 0.045820, 0.048882, 0.049675, 0.043484, 0.051538
	-0.045038, 0.028947, 0.019821, 0.012917, 0.013648, 0.007951, 0.005122, 0.007823, 0.012411, 0.015320, 0.025036, 0.036734, 0.045314, 0.052208, 0.062220, 0.065610, 0.068489, 0.066665, 0.068454, 0.069025, 0.071080, 0.073373, 0.079623, 0.085651, 0.088907, 0.088954, 0.084254, 0.084464, 0.080300, 0.072471, 0.067316, 0.066430, 0.065143, 0.057630, 0.058650, 0.059627, 0.057197, 0.054105, 0.055295, 0.057879
	-0.017117, 0.027364, 0.023067, 0.022758, 0.019246, 0.011825, 0.007962, 0.011522, 0.017237, 0.021779, 0.031329, 0.042642, 0.052349, 0.060322, 0.069568, 0.074657, 0.075211, 0.072882, 0.075373, 0.078391, 0.079512, 0.081816, 0.086101, 0.091730, 0.095061, 0.095682, 0.092100, 0.092873, 0.085769, 0.077219, 0.068392, 0.073179, 0.069972, 0.061240, 0.068306, 0.062227, 0.061008, 0.064520, 0.058543, 0.070728
	-0.042759, 0.035472, 0.029514, 0.023812, 0.024176, 0.020576, 0.017397, 0.018716, 0.022981, 0.027634, 0.041262, 0.050991, 0.058558, 0.067060, 0.077829, 0.083609, 0.084719, 0.082815, 0.085352, 0.087363, 0.091238, 0.091692, 0.096562, 0.102513, 0.106436, 0.108184, 0.105828, 0.107257, 0.102415, 0.090768, 0.084257, 0.081410, 0.081286, 0.073523, 0.074433, 0.076576, 0.070376, 0.068350, 0.071896, 0.072962
	-0.003143, 0.035517, 0.033266, 0.032727, 0.031843, 0.025862, 0.023177, 0.026936, 0.032953, 0.037457, 0.049289, 0.057429, 0.066625, 0.072540, 0.083814, 0.089321, 0.092420, 0.093053, 0.094752, 0.096876, 0.098364, 0.101271, 0.105185, 0.113505, 0.115784, 0.118957, 0.117138, 0.117934, 0.110930, 0.101497, 0.091051, 0.092731, 0.090574, 0.079282, 0.084691, 0.078426, 0.073451, 0.081698, 0.072811, 0.084352
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 19.8
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity
=======================
Starting Klippy...
Args: ['/home/pi/klipper/klippy/klippy.py', '/home/pi/printer_data/config/printer.cfg', '-l', '/home/pi/printer_data/logs/klippy.log', '-I', '/home/pi/printer_data/comms/klippy.serial', '-a', '/home/pi/printer_data/comms/klippy.sock']
Git version: 'v0.12.0-402-g2817b348e-dirty'
Untracked files: klippy/extras/beacon.py, klippy/extras/beacon_adaptive_heat_soak.py, klippy/extras/beacon_mesh.py, klippy/extras/beacon_true_zero_correction.py, klippy/extras/beacon_user_z_offset.py, klippy/extras/fastconfig.py, klippy/extras/gcode_shell_command.py, klippy/extras/linear_movement_vibrations.py, klippy/extras/named_offsets.py, klippy/extras/ratos.py, (+4 files)
Branch: master
Remote: origin
Tracked URL: https://github.com/Klipper3d/klipper.git
CPU: 4 core ?
Python: '3.9.2 (default, Jan 24 2026, 09:41:14) \n[GCC 10.2.1 20210110]'
Start printer at Tue Mar 17 03:55:13 2026 (1773719713.7 9318.0)
===== Config file =====
[mcu rpi]
serial = /tmp/klipper_host_mcu

[board_pins btt-octopus-pro-h723-11]
aliases = 
	
	
	
	x_step_pin=PF13,
	x_dir_pin=PF12,
	x_enable_pin=PF14,
	x_uart_pin=PC4,
	x_diag_pin=PG6,
	x_endstop_pin=PG6,
	
	
	
	dual_carriage_step_pin=PF9,
	dual_carriage_dir_pin=PF10,
	dual_carriage_enable_pin=PG2,
	dual_carriage_uart_pin=PF2,
	dual_carriage_diag_pin=PG12,
	dual_carriage_endstop_pin=PG12,
	
	
	
	y_step_pin=PG0,
	y_dir_pin=PG1,
	y_enable_pin=PF15,
	y_uart_pin=PD11,
	y_diag_pin=PG9,
	y_endstop_pin=PG9,
	
	
	
	y1_step_pin=PG4,
	y1_dir_pin=PC1,
	y1_enable_pin=PA2,
	y1_uart_pin=PC7,
	y1_diag_pin=PG11,
	y1_endstop_pin=PG11,
	
	
	
	z0_step_pin=PC13,
	z0_dir_pin=PF0,
	z0_enable_pin=PF1,
	z0_uart_pin=PE4,
	z0_diag_pin=PG13,
	
	
	
	z1_step_pin=PE2,
	z1_dir_pin=PE3,
	z1_enable_pin=PD4,
	z1_uart_pin=PE1,
	z1_diag_pin=PG14,
	
	
	
	z2_step_pin=PE6,
	z2_dir_pin=PA14,
	z2_enable_pin=PE0,
	z2_uart_pin=PD3,
	z2_diag_pin=PG15,
	
	e_step_pin=PF11,
	e_dir_pin=PG3,
	e_enable_pin=PG5,
	e_uart_pin=PC6,
	
	e_heater_pin=PA2,
	e_sensor_pin=PF4,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=PA7,
	stepper_spi_miso_pin=PA6,
	stepper_spi_sclk_pin=PA5,
	adxl345_cs_pin=PA15,
	bltouch_sensor_pin=PB7,
	bltouch_control_pin=PB6,
	probe_pin=PB7,
	fan_part_cooling_pin=PA8,
	fan_toolhead_cooling_pin=PE5,
	fan_controller_board_pin=PD12,
	heater_bed_heating_pin=PA1,
	heater_bed_sensor_pin=PF3,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PG15,
	filament_sensor_motion_pin=PG14,
	ratrig_vaoc_probe_pin=PG10,
	ratrig_vaoc_led_pin=PB0,
	ratrig_vaoc_fan_pin=PD13,
	chamber_lighting_pin=PB11,
	chamber_filter_4p_fan_pin=PD14,
	chamber_filter_4p_fan_enable_pin=PD15

[mcu]
serial = /dev/RatOS/btt-octopus-pro-h723-11

[temperature_sensor Octopus_Pro_H723_V1.1]
sensor_type = temperature_mcu

[adxl345 controlboard]
cs_pin = PA15
spi_software_mosi_pin = PB5
spi_software_miso_pin = PB4
spi_software_sclk_pin = PB3

[board_pins toolboard_t0]
mcu = toolboard_t0
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t0]
serial = /dev/RatOS/btt-ebb42-gen2-10-t0

[temperature_sensor EBB42_Gen2_v1.0_T0]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t0

[lis2dw toolboard_t0]
axes_map = x, z, y
cs_pin = toolboard_t0:PB1
spi_software_mosi_pin = toolboard_t0:PB11
spi_software_miso_pin = toolboard_t0:PB2
spi_software_sclk_pin = toolboard_t0:PB10

[board_pins toolboard_t1]
mcu = toolboard_t1
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t1]
serial = /dev/RatOS/btt-ebb42-gen2-10-t1

[temperature_sensor EBB42_Gen2_v1.0_T1]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t1

[lis2dw toolboard_t1]
axes_map = x, z, y
cs_pin = toolboard_t1:PB1
spi_software_mosi_pin = toolboard_t1:PB11
spi_software_miso_pin = toolboard_t1:PB2
spi_software_sclk_pin = toolboard_t1:PB10

[gcode_macro RatOS]
variable_homing = "endstops"
variable_z_probe = "static"
variable_sensorless_x_current = 0.6
variable_sensorless_y_current = 0.9
variable_safe_home_x = "middle"
variable_safe_home_y = "middle"
variable_driver_type_x = "tmc2209"
variable_driver_type_y = "tmc2209"
variable_stowable_probe_stop_on_error = False
variable_chamber_filter_enable = True
variable_chamber_filter_speed = 0.5
variable_chamber_filter_disable_speed = 1.0
variable_chamber_filter_enable_at = "after_print_start"
variable_chamber_filter_disable_period = 300
variable_chamber_filter_disable_bed_temp = 0
variable_chamber_heater_enable = True
variable_chamber_heater_bed_temp = 115
variable_chamber_heater_preheating_temp = 150
variable_chamber_heater_heating_temp_offset = 25
variable_chamber_heater_control_external_heater = False
variable_chamber_heater_air_circulation_enable = True
variable_chamber_heater_air_circulation_fan_speed = 0.35
variable_chamber_heater_air_circulation_y_pos = 0
variable_chamber_heater_air_circulation_z_pos = 100
variable_chamber_heater_extra_fan_speed = 1.0
variable_chamber_heater_filter_fan_speed = 1.0
variable_bed_heat_soak_time = 0
variable_hotend_heat_soak_time = 0
variable_led_status_action = 0.0,1.0,1.0
variable_led_status_success = 0.0,1.0,0.0
variable_led_status_error = 1.0,0.0,1.0
variable_led_status_on = 1.0,1.0,1.0
variable_led_status_off = 0.0,0.0,1.0
variable_led_status_standby = 0.1,0.1,0.1
variable_led_status_heating = 1.0,0.0,0.0
variable_led_status_cooling = 0.0,0.0,1.0
variable_calibrate_bed_mesh = True
variable_adaptive_mesh = True
variable_start_print_park_in = "center"
variable_start_print_park_z_height = 3
variable_end_print_park_in = "back"
variable_pause_print_park_in = "back"
variable_end_print_park_z_hop = 20
variable_nozzle_priming = "primeblob"
variable_nozzle_prime_start_x = "max"
variable_nozzle_prime_start_y = "min"
variable_nozzle_prime_direction = "auto"
variable_nozzle_prime_bridge_fan = 102
variable_probe_for_priming_result = None
variable_probe_for_priming_end_result = None
variable_probe_for_priming_result_t1 = None
variable_probe_for_priming_end_result_t1 = None
variable_probe_for_priming_disable_mesh_constraints = False
variable_adaptive_prime_offset_threshold = -1.0
variable_last_z_offset = None
variable_runout_park_in = "front"
variable_enable_unload_tip_forming = False
variable_filament_unload_length = 150
description = RatOS variable storage macro, will echo variables to the console when run.
variable_relative_extrusion = True
variable_force_absolute_position = False
variable_preheat_extruder = True
variable_preheat_extruder_temp = 150
variable_macro_travel_speed = 600
variable_macro_travel_accel = 8000
variable_macro_z_speed = 15
variable_bed_margin_x = [59.6, 59.6]
variable_bed_margin_y = [14.35, 33.65]
variable_printable_x_min = 0
variable_printable_x_max = 0
variable_printable_y_min = 0
variable_printable_y_max = 0
variable_end_print_motors_off = True
variable_status_color_ok = "00FF00"
variable_status_color_error = "FF0000"
variable_status_color_unknown = "FFFF00"
variable_end_print_retract_filament = 10
gcode = 
	ECHO_RATOS_VARS
variable_auto_center_subject = False
variable_toolchange_zhop = 2.0
variable_toolchange_zspeed = 25
variable_toolchange_sync_fans = False
variable_toolchange_combined_zhop = False
variable_toolchange_travel_speed = 600
variable_toolchange_travel_accel = 8000
variable_toolchange_extrusion = 2.0
variable_toolchange_retraction = 2.0
variable_toolchange_feedrate = 7200
variable_toolchange_prepurging_timer = 0
variable_toolchange_standby_temp = -1
variable_toolchange_purge = 25
variable_toolchange_first_purge = 50
variable_beacon_bed_mesh_scv = 25
variable_beacon_contact_z_homing = False
variable_beacon_contact_start_print_true_zero = True
variable_beacon_contact_start_print_true_zero_fuzzy_position = True
variable_beacon_contact_calibrate_model_on_true_zero = True
variable_beacon_contact_wipe_before_true_zero = True
variable_beacon_contact_wipe_before_true_zero_method = "probe_clean"
variable_beacon_contact_true_zero_temp = 170
variable_beacon_contact_prime_probing = True
variable_beacon_contact_expansion_compensation = True
variable_beacon_contact_bed_mesh = False
variable_beacon_contact_bed_mesh_samples = 2
variable_beacon_contact_z_tilt_adjust = False
variable_beacon_contact_z_tilt_adjust_samples = 2
variable_beacon_scan_compensation_enable = True
variable_beacon_scan_compensation_profile = "auto"
variable_beacon_scan_compensation_desired_spacing = 10
variable_beacon_scan_compensation_bed_temp_mismatch_is_error = False
variable_beacon_contact_poke_bottom_limit = -1
variable_beacon_scan_method_automatic = False
variable_beacon_adaptive_heat_soak = True
variable_beacon_adaptive_heat_soak_max_wait = 5400
variable_beacon_adaptive_heat_soak_extra_wait_after_completion = 0
variable_beacon_adaptive_heat_soak_layer_quality = 3
variable_beacon_adaptive_heat_soak_maximum_first_layer_duration = 1800
variable_beacon_contact_start_print_true_zero_fuzzy_radius = 20
variable_homing_x = "endstop"
variable_homing_y = "endstop"
variable_default_toolhead = 0
variable_adxl_chip = ["lis2dw toolboard_t0", "lis2dw toolboard_t1"]
variable_shaper_x_freq = [54.2, 53.2, 53.6, 54.4]
variable_shaper_y_freq = [40.8, 47.6, 38.6, 38]
variable_shaper_x_type = ["mzv", "mzv", "mzv", "mzv"]
variable_shaper_y_type = ["mzv", "mzv", "mzv", "mzv"]
variable_x_driver_types = ["tmc5160"]
variable_x_axes = ["x"]
variable_y_driver_types = ["tmc5160", "tmc5160"]
variable_y_axes = ["y", "y1"]
variable_z_driver_types = ["tmc2209", "tmc2209", "tmc2209"]
variable_z_axes = ["z", "z1", "z2"]
variable_home_y_first = True

[ratos_homing]
axes = xyz
z_hop = 15
z_hop_speed = 15
gcode = 
	
	_LED_ON
	
	
	{% set prev_stop_on_error = printer["gcode_macro RatOS"].stowable_probe_stop_on_error %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set target_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	_IDEX_SINGLE
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE=True
	
	
	M400
	
	G90
	
	
	{% set X = true if params.X is defined else false %}
	{% set Y = true if params.Y is defined else false %}
	{% set Z = true if params.Z is defined else false %}
	{% if printer["gcode_macro RatOS"].home_y_first|default(false)|lower == 'true' %}
	HOME_Y X={X} Y={Y} Z={Z}
	HOME_X X={X} Y={Y} Z={Z}
	{% else %}
	HOME_X X={X} Y={Y} Z={Z}
	HOME_Y X={X} Y={Y} Z={Z}
	{% endif %}
	HOME_Z X={X} Y={Y} Z={Z}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE={prev_stop_on_error}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[gcode_macro HOME_X]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_x = printer["gcode_macro RatOS"].homing_x|lower %}
	{% set homing_x = homing_x if homing_x else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_X" MSG="printable_x_max: {printable_x_max}, safe_home_x: {safe_home_x}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}"
	
	
	{% if X or not Y and not Z %}
	{% if homing_x == 'endstop' %}
	G28 X
	{% elif homing_x == 'sensorless' %}
	{% if printer["dual_carriage"] is defined %}
	{ action_emergency_stop("sensorless homing not supported on IDEX!") }
	{% endif %}
	HOME_X_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_x to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_x, homing)) }
	{% endif %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1} MODE=PRIMARY
	G1 X{parking_position} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	{% endif %}
	{% set x_homed = True %}
	G0 X{safe_home_x} F{speed}
	M400
	{% endif %}

[gcode_macro HOME_Y]
gcode = 
	
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_y = printer["gcode_macro RatOS"].homing_y|lower %}
	{% set homing_y = homing_y if homing_y else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Y" MSG="printable_y_max: {printable_y_max}, safe_home_y: {safe_home_y}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}"
	
	
	{% if Y or not X and not Z %}
	{% if homing_y == 'endstop' %}
	G28 Y
	{% elif homing_y == 'sensorless' %}
	HOME_Y_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_y to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_y, homing)) }
	{% endif %}
	{% set y_homed = True %}
	G0 Y{safe_home_y} F{speed}
	{% endif %}

[gcode_macro HOME_Z]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	
	
	{% set beacon_contact_z_homing = true if printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_z_home_position_fuzzing_radius = printer["gcode_macro RatOS"].beacon_z_home_position_fuzzing_radius|default(0)|float %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Z" MSG="x_homed: {x_homed}, y_homed: {y_homed}, z_probe: {z_probe}, beacon_contact_z_homing: {beacon_contact_z_homing}"
	
	
	{% if Z or not Y and not X %}
	RATOS_ECHO MSG="Homing Z"
	{% if x_homed == False or y_homed == False %}
	{ action_emergency_stop("X and Y must be homed before homing Z") }
	{% else %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_homing %}
	{% if beacon_contact_start_print_true_zero %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% else %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	{% else %}
	G28 Z
	{% endif %}
	_Z_HOP
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro HOME_X_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	
	G4 P300
	
	G28 X
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"

[gcode_macro HOME_Y_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	
	G4 P300
	
	G28 Y
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"

[gcode_macro _Z_HOP]
description = Move Z axis up by Z_HOP distance at Z_HOP_SPEED. In relative mode it will move Z axis up by Z_HOP distance. In absolute mode it will move Z axis to Z_HOP distance.
gcode = 
	{% set z_hop = printer.fastconfig.config.ratos_homing.z_hop|float %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	G0 Z{z_hop} F{z_hop_speed}

[gcode_macro __MOVE_TO_SAFE_Z_HOME_ECHO_DEBUG]
gcode = 
	DEBUG_ECHO PREFIX="_MOVE_TO_SAFE_Z_HOME" MSG="x: {params.X}, y: {params.Y}, z_hop: {params.Z_HOP}, fuzzy_radius: {params.FUZZY_RADIUS}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}, printable_x_max: {printer['gcode_macro RatOS'].printable_x_max}, printable_y_max: {printer['gcode_macro RatOS'].printable_y_max}"

[gcode_macro MAYBE_HOME]
description = Only home unhomed axis. Specify ABL=1 to also ensure that automatic bed levelling is applied (if configured).
variable_is_kinematic_position_overriden = False
gcode = 
	{% set abl = params.ABL|default('')|lower in ('true', 'yes', '1') %}
	{% if printer["gcode_macro MAYBE_HOME"].is_kinematic_position_overriden|lower == 'true' %}
	RATOS_ECHO MSG="SET_CENTER_KINEMATIC_POSITION has been abused. Homing all axes. Please refrain from using SET_CENTER_KINEMATIC_POSITION outside of debugging purposes."
	G28
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=False
	{% else %}
	{% set axes = '' %}
	{% set isHomed = true %}
	{% set axesToHome = '' %}
	{% if params.X is defined %}
	{% set axes = axes ~ 'X ' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% endif %}
	{% if params.Y is defined %}
	{% set axes = axes ~ 'Y ' %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% endif %}
	{% if params.Z is defined %}
	{% set axes = axes ~ 'Z ' %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if params.X is not defined and params.Y is not defined and params.Z is not defined %}
	{% set axes = '' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if isHomed is false %}
	RATOS_ECHO MSG="Homing {axesToHome}"
	G28 {axesToHome}
	{% else %}
	RATOS_ECHO MSG="All requested axes already homed. Skipping homing."
	{% endif %}
	{% endif %}
	{% if abl %}
	{% if printer.z_tilt is defined %}
	{% if not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Performing Z tilt adjustment..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Z tilt already applied. Skipping Z tilt adjustment."
	{% endif %}
	{% elif printer.quad_gantry_level is defined %}
	{% if not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Performing quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Quad gantry leveling already applied. Skipping quad gantry leveling."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="No automatic bed leveling method configured. Skipping bed leveling."
	{% endif %}
	{% endif %}

[gcode_macro PID_CALIBRATE_HOTEND]
description = Perform a PID calibration test for a given extruder heater.
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set temp = params.TEMP|default(220)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_HOTEND" MSG="TEMP={temp}"
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO MSG="PID calibration hotend heater T0 at {temp}°C..."
	PID_CALIBRATE HEATER=extruder TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	
	{% if toolhead==0 or toolhead==1 %}
	RATOS_ECHO MSG="PID calibration hotend heater T{toolhead} at {temp}°C..."
	PID_CALIBRATE HEATER=extruder{'' if toolhead==0 else toolhead} TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_BED]
description = Perform a PID calibration test for the bed heater.
gcode = 
	
	{% set temp = params.TEMP|default(80)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_BED" MSG="TEMP={temp}"
	RATOS_ECHO MSG="PID calibration bed heater at {temp}°C..."
	
	
	PID_CALIBRATE HEATER=heater_bed TARGET={temp}
	
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_CHAMBER_HEATER]
description = Perform a PID calibration test for the chamber heater.
gcode = 
	
	{% set temp = params.TEMP|default(150)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_CHAMBER_HEATER" MSG="TEMP={temp}"
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	RATOS_ECHO MSG="PID calibration chamber heater at {temp}°C..."
	PID_CALIBRATE HEATER=chamber_heater TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_heater" %}
	{% set link_text = "RatOS Chamber Heater" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber heater found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro INITIALIZE_PA_TUNING]
description = Start a pressure advance tuning tower.
gcode = 
	
	{% set start = params.START|default(0.0)|float %}
	{% set factor = params.FACTOR|default(0.001)|float %}
	
	
	{% set layer_number = printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|default(0)|int %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if is_printing_gcode and layer_number < 2 %}
	DEBUG_ECHO PREFIX="START_PA_TOWER" MSG="START: {start}, FACTOR: {factor}"
	RATOS_ECHO MSG="Starting pressure advance tuning tower..."
	TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START={start} FACTOR={factor}
	{% else %}
	RATOS_ECHO MSG="Pressure advance tuning tower requires you to be printing gcode and on layer 1 to start."
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro CHAMBER_FILTER_ON]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	_CHAMBER_FILTER_TURN_ON
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro CHAMBER_FILTER_OFF]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Deactivating chamber filter..."
	_CHAMBER_FILTER_TURN_OFF
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set chamber_filter_enable_at = printer["gcode_macro RatOS"].chamber_filter_enable_at|default('after_print_start')|lower %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_ON" MSG="at: {at}, chamber_filter_enable: {chamber_filter_enable}, chamber_filter_enable_at: {chamber_filter_enable_at}, chamber_filter_speed: {chamber_filter_speed}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	{% if chamber_filter_enable_at == at %}
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	
	
	_CHAMBER_FILTER_TURN_ON AT={at}
	
	
	{% if chamber_filter_enable_at == "print_end" %}
	_LED_CHAMBER_FILTER_ON
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_OFF]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF" MSG="chamber_filter_enable: {chamber_filter_enable}, filter_disable_period: {filter_disable_period}, filter_disable_bed_temp: {filter_disable_bed_temp}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	
	{% if filter_disable_period > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting {filter_disable_period} seconds before turning chamber filter off..."
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION={filter_disable_period}
	{% endif %}
	
	
	{% if filter_disable_bed_temp > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting for bed temp to cool down to {filter_disable_bed_temp}°C to turn filter off..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM=0 MAXIMUM={filter_disable_bed_temp}
	_CHAMBER_FILTER_TURN_OFF
	_LED_CHAMBER_FILTER_OFF
	{% endif %}
	
	{% endif %}

[delayed_gcode _CHAMBER_FILTER_OFF_TIMER]
gcode = 
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF_TIMER" MSG="executed"
	
	
	_CHAMBER_FILTER_TURN_OFF
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Chamber filter turned off!"
	
	
	_LED_CHAMBER_FILTER_OFF

[gcode_macro _CHAMBER_FILTER_TURN_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_speed|default(0)|float %}
	{% if at == "print_end" %}
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_disable_speed|default(0)|float %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION=0
	
	
	SET_FAN_SPEED FAN=filter SPEED={chamber_filter_speed}

[gcode_macro _CHAMBER_FILTER_TURN_OFF]
gcode = 
	
	SET_FAN_SPEED FAN=filter SPEED=0

[gcode_macro _CHAMBER_FILTER_SANITY_CHECK]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	{% if filter_disable_bed_temp > 0 and filter_disable_period > 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable, not both.")}
	{% endif %}
	
	{% if filter_disable_bed_temp == 0 and filter_disable_period == 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable.")}
	{% endif %}
	
	{% endif %}

[gcode_macro CHAMBER_HEATER_ON]
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(45)|int %}
	
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp} IS_FROM_START_PRINT=False

[gcode_macro CHAMBER_HEATER_OFF]
gcode = 
	_CHAMBER_HEATER_OFF

[gcode_macro _CHAMBER_HEATER_ON]
variable_chamber_temp = 0
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	{% set is_from_start_print = true if params.IS_FROM_START_PRINT|default(True)|lower == 'true' else false %}
	
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set chamber_heater_enable = true if printer["gcode_macro RatOS"].chamber_heater_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}
	{% set chamber_heater_preheating_temp = printer["gcode_macro RatOS"].chamber_heater_preheating_temp|default(150)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	{% set chamber_heater_control_external_heater = true if printer["gcode_macro RatOS"].chamber_heater_control_external_heater|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_enable = true if printer["gcode_macro RatOS"].chamber_heater_air_circulation_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_fan_speed = printer["gcode_macro RatOS"].chamber_heater_air_circulation_fan_speed|default(0.35)|float %}
	{% set chamber_heater_air_circulation_y_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_y_pos|default(0)|float %}
	{% set chamber_heater_air_circulation_z_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_z_pos|default(100)|float %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_HEATER_ON" MSG="chamber_heater_enable: {chamber_heater_enable}, chamber_heater_preheating_temp: {chamber_heater_preheating_temp}, chamber_heater_heating_temp_offset: {chamber_heater_heating_temp_offset}, bed_temp: {bed_temp}, chamber_temp: {chamber_temp}, start_chamber_temp: {start_chamber_temp}"
	
	
	{% if chamber_heater_enable and chamber_temp > 0 and chamber_heater_bed_temp > 0 %}
	
	
	_LED_HEATING
	
	
	RATOS_ECHO MSG="Preheating chamber to {(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}°C..."
	
	
	{% set chamber_temp_sensor = "extruder" %}
	{% if printer["dual_carriage"] is defined and default_toolhead == 1 %}
	{% set chamber_temp_sensor = "extruder1" %}
	{% endif %}
	{% if printer["temperature_sensor chamber"] is defined %}
	{% set chamber_temp_sensor = "temperature_sensor chamber" %}
	{% endif %}
	
	
	{% set current_chamber_temp = printer['%s' % chamber_temp_sensor].temperature|int %}
	
	
	{% set needs_heating = current_chamber_temp < (start_chamber_temp if start_chamber_temp > 0 else chamber_temp) %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_BEFORE_PREHEATING
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	{% if not is_from_start_print %}
	MAYBE_HOME
	{% endif %}
	G0 Z{chamber_heater_air_circulation_z_pos} F{z_speed}
	G0 Y{chamber_heater_air_circulation_y_pos} F{speed}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * chamber_heater_air_circulation_fan_speed)}
	{% endif %}
	{% else %}
	{% if is_from_start_print %}
	G0 Z{z} F{z_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE={chamber_temp}
	
	
	{% if needs_heating %}
	
	
	M140 S{chamber_heater_bed_temp}
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={chamber_heater_preheating_temp}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	
	{% endif %}
	
	
	{% if needs_heating %}
	_CHAMBER_HEATER_EXTRA_FAN_ON
	{% endif %}
	
	
	{% if needs_heating %}
	TEMPERATURE_WAIT SENSOR="{chamber_temp_sensor}" MINIMUM={(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% endif %}
	
	
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED=0
	_CHAMBER_FILTER_ON AT="before_print_start"
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	G28 Z
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_AFTER_PREHEATING
	{% endif %}
	
	
	{% if printer["temperature_sensor chamber"] is defined %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined and chamber_heater_control_external_heater %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	
	
	_LED_SUCCESS
	
	{% endif %}

[gcode_macro _CHAMBER_HEATER_OFF]
gcode = 
	RATOS_ECHO MSG="Deactivating chamber heater..."
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=0
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE=0
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	
	
	_CHAMBER_HEATER_EXTRA_FAN_OFF

[delayed_gcode _CHAMBER_HEATER_CONTROL]
initial_duration = 0.
gcode = 
	
	{% set chamber_temp = printer["gcode_macro _CHAMBER_HEATER_ON"].chamber_temp|default(0)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	
	
	{% set current_chamber_temp = printer['temperature_sensor chamber'].temperature|int %}
	
	
	{% if current_chamber_temp < chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	{% endif %}
	
	
	{% if current_chamber_temp >= chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_ON]
gcode = 
	
	{% set chamber_heater_extra_fan_speed = printer["gcode_macro RatOS"].chamber_heater_extra_fan_speed|default(0.0)|float %}
	
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	{% if chamber_heater_extra_fan_speed > 0 %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED={chamber_heater_extra_fan_speed}
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_OFF]
gcode = 
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED=0
	{% endif %}

[gcode_macro _USER_CHAMBER_HEATER_BEFORE_PREHEATING]
description = Will be executed before chamber preheating, only if heating is needed.
gcode = 

[gcode_macro _USER_CHAMBER_HEATER_AFTER_PREHEATING]
description = Will be executed after chamber preheating, only if heating was needed.
gcode = 

[gcode_macro RESET_HEATSOAK_SETTINGS]
description = Resets all heatsoak-related settings to startup defaults
gcode = 
	HEATSOAK_SETTINGS ACTION=reset

[gcode_macro USE_ADAPTIVE_HEATSOAK]
description = Temporarily enables adaptive bed heatsoaking (if a beacon probe is present), will reset to printer.cfg settings
	when Klipper is restarted. Optionally specify QUALITY (1-5) and maximum FIRST_LAYER_DURATION (in minutes).
	Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.QUALITY|default("1..5") %}
	{% set _ = params.FIRST_LAYER_DURATION|default("1..120 minutes") %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("Adaptive heatsoaking is only available when a beacon probe is configured.") }
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_quality = (settings.variable_beacon_adaptive_heat_soak_layer_quality if defsrc == 'startup' else current.beacon_adaptive_heat_soak_layer_quality)|default(3)|int %}
	{% set default_first_layer_duration_secs = (settings.variable_beacon_adaptive_heat_soak_maximum_first_layer_duration if defsrc == 'startup' else current.beacon_adaptive_heat_soak_maximum_first_layer_duration)|default(1800)|int %}
	{% if params2.QUALITY is defined %}
	{% set quality = params2.QUALITY|int %}
	{% if quality < 1 or quality > 5 %}
	{ action_raise_error("QUALITY must be between 1 (rough) and 5 (maximum). Use 3 (normal) if unsure.") }
	{% endif %}
	{% else %}
	{% set quality = default_quality %}
	{% endif %}
	{% if params2.FIRST_LAYER_DURATION is defined %}
	{% set first_layer_duration_mins = params2.FIRST_LAYER_DURATION|float %}
	{% if first_layer_duration_mins <= 0 %}
	{ action_raise_error("FIRST_LAYER_DURATION must be a positive number specifying the maximum first layer duration in minutes.") }
	{% endif %}
	{% if first_layer_duration_mins > 120 %}
	CONSOLE_ECHO MSG="FIRST_LAYER_DURATION will be limited to 120 minutes. Values larger than this will not have an effect on soak time."
	{% set first_layer_duration_mins = 120 %}
	{% endif %}
	{% set first_layer_duration_secs = (first_layer_duration_mins * 60.0)|int %}
	{% else %}
	{% set first_layer_duration_secs = default_first_layer_duration_secs %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	{% endif %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=True beacon_adaptive_heat_soak_layer_quality={quality} beacon_adaptive_heat_soak_maximum_first_layer_duration={first_layer_duration_secs}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."

[gcode_macro USE_FIXED_HEATSOAK]
description = Temporarily enables fixed bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
	Optionally specify DURATION (in minutes). Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.DURATION|default("0..720 minutes") %}
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_duration = (settings.variable_bed_heat_soak_time if defsrc == 'startup' else current.bed_heat_soak_time)|default(0)|int %}
	{% if params2.DURATION is defined %}
	{% set duration_mins = params2.DURATION|float %}
	{% if duration_mins < 0 %}
	{ action_raise_error("DURATION must be a non-negative number specifying the heatsoak duration in minutes.") }
	{% endif %}
	{% if duration_mins > 720 %}
	CONSOLE_ECHO MSG="DURATION will be limited to 720 minutes (12 hours). If you really need a larger value, adjust printer.cfg instead."
	{% set duration_mins = 720 %}
	{% endif %}
	{% set duration_secs = (duration_mins * 60.0)|int %}
	{% else %}
	{% set duration_secs = default_duration %}
	{% set duration_mins = duration_secs / 60.0 %}
	{% endif %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% if has_beacon %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=False bed_heat_soak_time={duration_secs}
	{% else %}
	HEATSOAK_SETTINGS QUIET=1 bed_heat_soak_time={duration_secs}
	{% endif %}
	{% if duration_mins < 1e-3 %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% else %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% endif %}

[gcode_macro USE_NO_HEATSOAK]
description = Temporarily disables bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
gcode = 
	USE_FIXED_HEATSOAK DURATION=0

[gcode_macro HEATSOAK_SETTINGS]
description = Shows or adjusts heatsoak settings
	- With no arguments: shows current heatsoak settings, specify VERBOSE=1 for detailed output
	- With arguments: sets the specified settings. Use the full setting name without the variable_ prefix, e.g. bed_heat_soak_time=300 or beacon_adaptive_heat_soak_layer_quality=4. See printer.cfg for available settings.
variable_default_source = "startup"
gcode = 
	
	{% set params2 = params %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% set quiet = params2.pop("QUIET", None)|default("0") in ("1", "true", "yes") %}
	{% set verbose = params2.pop("VERBOSE", None)|default("0") in ("1", "true", "yes") %}
	{% if has_beacon %}
	{% set vars = (
	"beacon_adaptive_heat_soak",
	"beacon_adaptive_heat_soak_max_wait",
	"beacon_adaptive_heat_soak_extra_wait_after_completion",
	"beacon_adaptive_heat_soak_layer_quality",
	"beacon_adaptive_heat_soak_maximum_first_layer_duration",
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% else %}
	{% set vars = (
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% endif %}
	{% set action = "show" if params|length == 0 else params2.ACTION %}
	{% if action is defined and params|length > 1 %}
	{ action_raise_error("ACTION cannot be specified with other parameters.") }
	{% elif action is not defined %}
	{% for k, v in params2.items() %}
	{% set k = k|lower %}
	{% if k in vars %}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Setting {k} to {v}"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={k} VALUE={v}
	{% else %}
	{ action_raise_error("Parameter '%s' is not recognised. Note that adaptive heatsoaking settings can only be set when a beacon probe is configured." % k) }
	{% endif %}
	{% endfor %}
	{% elif action == "reset" %}
	_RESET_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	CONSOLE_ECHO MSG="Heatsoak settings have been reset to their original values."
	{% elif action == "show" %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% set is_adaptive = False if not has_beacon else current.beacon_adaptive_heat_soak|default("")|lower == "true" %}
	{% if is_adaptive %}
	{% set quality = current.beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set first_layer_duration_secs = current.beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."
	{% elif current.bed_heat_soak_time|default(0)|int > 0 %}
	{% set duration_mins = (current.bed_heat_soak_time|int / 60.0) %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% else %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% endif %}
	{% if verbose %}
	CONSOLE_ECHO MSG="Detailed settings:"
	_SHOW_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	{% endif %}
	{% else %}
	{ action_raise_error("Action '%s' is not recognised" % action) }
	{% endif %}

[gcode_macro _LED_START_PRINTING]
gcode = 
	_LED_ACTION

[gcode_macro _LED_START_PRINTING_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_PRINTING]
gcode = 
	_LED_ON TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_PAUSE]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_ON]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_OFF]
gcode = 
	_LED_STANDBY

[gcode_macro _LED_LOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_LOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_RUNOUT]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_CLOG]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_UNLOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_UNLOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_DEACTIVATE_TOOLHEAD]
gcode = 
	_LED_OFF TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_STANDBY]
gcode = 
	_LED_STANDBY TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_WAKEUP]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_MOTORS_OFF]
gcode = 
	_LED_STANDBY
	_LED_VAOC_OFF

[gcode_macro _LED_INPUT_SHAPER_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_INPUT_SHAPER_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_BEACON_CALIBRATION_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_VAOC_ON]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=1.0 GREEN=1.0 BLUE=1.0
	{% endif %}

[gcode_macro _LED_VAOC_OFF]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=0.0 GREEN=0.0 BLUE=0.0
	{% endif %}

[gcode_macro _LED_ACTION]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_action %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SUCCESS]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_success %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_HEATING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_heating %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_COOLING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_cooling %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ERROR]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_error %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ON]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_on %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_OFF]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_off %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_STANDBY]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_standby %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}
	
	{% if toolhead >= 0 %}
	{% if printer['neopixel nozzle_led_t%s' % toolhead] is defined  %}
	SET_LED LED={'nozzle_led_t%s' % toolhead} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% else %}
	{% if printer['neopixel nozzle_led_t0'] is defined  %}
	SET_LED LED={'nozzle_led_t0'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% if printer['neopixel nozzle_led_t1'] is defined %}
	SET_LED LED={'nozzle_led_t1'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% endif %}
	
	_USER_LED_SET { rawparams }

[gcode_macro _USER_LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}

[gcode_macro LOAD_FILAMENT]
description = Loads new filament. Note: be careful with PETG, make sure you inspect the tip of your filament before loading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% if filament_name == '' or filament_type == '' %}
	{% set filament_name = 'unknown' %}
	{% set filament_type = 'unknown' %}
	{% endif %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_LOAD_FILAMENT TEMP={temp} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_LOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_LOAD_FILAMENT]
description = Load filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_LOAD_FILAMENT" MSG="TEMP={temp}"
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=load_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	_LOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	
	
	RESTORE_GCODE_STATE NAME=load_state
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament load routine complete, please check that the filament was loaded correctly."

[gcode_macro _IDEX_LOAD_FILAMENT]
description = Load filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament into T{toolhead}..."
	
	DEBUG_ECHO PREFIX="_IDEX_LOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	_LOAD_FILAMENT TOOLHEAD={toolhead} TEMP={temp} AUTOMATED={automated}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="Filament load routine for T{toolhead} complete, please check that the filament was loaded correctly."

[gcode_macro _LOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default(false)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE TOOLHEAD={toolhead}
	_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into hotend.."
	G92 E0
	G0 E{extruder_gear_to_cooling_position_distance} F{extruder_load_speed}
	G92 E0
	M400
	RATOS_ECHO MSG="Filament loaded into hotend."

[gcode_macro _LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set load_speed = printer["gcode_macro T%s" % toolhead].filament_load_speed|float * 60 %}
	{% set filament_loading_nozzle_offset = printer["gcode_macro T%s" % toolhead].filament_loading_nozzle_offset|float %}
	{% set cooling_position_to_nozzle_distance = printer["gcode_macro T%s" % toolhead].cooling_position_to_nozzle_distance|float %}
	{% set purge_after_load = printer["gcode_macro T%s" % toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into nozzle... Please wait!"
	G92 E0
	
	G0 E{cooling_position_to_nozzle_distance + filament_loading_nozzle_offset} F{load_speed}
	G92 E0
	G4 P1000
	_PURGE_FILAMENT	TOOLHEAD={toolhead} E={purge_after_load}
	RATOS_ECHO MSG="Filament loaded into nozzle!"

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"
	
	
	{% set filament_grabbing_length = printer["gcode_macro T%s" % toolhead].filament_grabbing_length|float %}
	{% set filament_grabbing_speed = printer["gcode_macro T%s" % toolhead].filament_grabbing_speed|float %}
	{% set resume_after_insert = true if printer["gcode_macro T%s" % toolhead].resume_after_insert|default(true)|lower == 'true' else false %}
	{% set enable_insert_detection = true if printer["gcode_macro T%s" % toolhead].enable_insert_detection|default(true)|lower == 'true' else false %}
	
	
	{% set current_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	
	{% if enable_insert_detection %}
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="toolhead: {toolhead}, filament_grabbing_length: {filament_grabbing_length}, filament_grabbing_speed: {filament_grabbing_speed}, current_idex_mode: {current_idex_mode}"
	
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	RATOS_ECHO MSG="Filament inserted into T{toolhead}, loading..."
	
	
	FORCE_MOVE STEPPER={'extruder%s' % ('' if toolhead == 0 else toolhead)} DISTANCE={filament_grabbing_length} VELOCITY={filament_grabbing_speed}
	M400
	
	
	{% if printer.pause_resume.is_paused %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% if resume_after_insert %}
	RESUME
	{% endif %}
	{% else %}
	{% if not printer.virtual_sdcard.is_active %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"

[gcode_macro _PURGE_BEFORE_UNLOAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set purge_before_unload = printer["gcode_macro T%s" % toolhead].purge_before_unload|float %}
	
	DEBUG_ECHO PREFIX="_PURGE_BEFORE_UNLOAD" MSG="TOOLHEAD: {toolhead}"
	
	
	{% if purge_before_unload > 0 %}
	G92 E0
	G0 E{purge_before_unload} F300
	G92 E0
	M400
	{% endif %}

[gcode_macro _PURGE_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set e = params.E|int %}
	{% set r = params.R|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_PURGE_FILAMENT" MSG="TOOLHEAD: {toolhead}, E: {e}"
	
	
	{% if e > 0 %}
	
	
	G92 E0
	G0 E{e} F300
	G92 E0
	M400
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={0.4 if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={0.4 if toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * 0.4)}
	{% endif %}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if r > 0 %}
	G92 E0
	G0 E-{r} F300
	G92 E0
	M400
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro _MOVE_TO_LOADING_POSITION]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_MOVE_TO_LOADING_POSITION" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	
	G1 X{loading_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _CLEANING_MOVE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_CLEANING_MOVE" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].parking_position is defined and printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set parking_position = printer["gcode_macro T%s" % toolhead].parking_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	{% set cleaning_position = loading_position %}
	{% if loading_position == parking_position %}
	{% if loading_position > 0 %}
	{% set cleaning_position = loading_position - 30 %}
	{% else %}
	{% set cleaning_position = loading_position + 30 %}
	{% endif %}
	{% endif %}
	
	
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _BED_MESH_SANITY_CHECK]
gcode = 
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is defined %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_start_print_true_zero_fuzzy_position %}
	CONSOLE_ECHO TYPE="error" TITLE="Defined zero reference not compatible with fuzzy true zero" MSG="Using fuzzy start print true zero position is not compatible with a defined zero_reference_position value in the [bed_mesh] section in printer.cfg._N_Please remove the zero_reference_position value from the [bed_mesh] section, or disable fuzzy true zero position in printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_start_print_true_zero_fuzzy_position: False"
	_STOP_AND_RAISE_ERROR MSG="Defined zero reference not compatible with fuzzy true zero"
	{% elif zero_ref_pos[0]|float|round != safe_home_x|float|round or zero_ref_pos[1]|float|round != safe_home_y|float|round %}
	CONSOLE_ECHO TYPE="error" TITLE="Zero reference position does not match safe home position" MSG="Please update your bed mesh zero reference position in printer.cfg, like so:_N__N_[bed_mesh]_N_zero_reference_position: {safe_home_x|float|round},{safe_home_y|float|round}_N_"
	_STOP_AND_RAISE_ERROR MSG="Zero reference position does not match safe home position"
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_bed_mesh %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact bed mesh is enabled" MSG="Beacon contact bed mesh is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_bed_mesh: False"
	{% endif %}
	
	{% if beacon_scan_method_automatic %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon 'automatic' scan method is enabled" MSG="Beacon 'automatic' scan method is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_scan_method_automatic: False"
	{% endif %}
	
	{% if beacon_contact_z_tilt_adjust %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact z-tilt adjust is enabled" MSG="Beacon contact z-tilt adjust is enabled. This is not recommended for normal use and may result in inaccurate z-tilt adjustment._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_z_tilt_adjust: False"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH]
gcode = 
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE=None
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE=None
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION {rawparams}
	{% endif %}

[gcode_macro _START_PRINT_BED_MESH]
variable_actual_true_zero_position_x = None
variable_actual_true_zero_position_y = None
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set X=[params.X0|default(-1)|float, params.X1|default(-1)|float] %}
	{% set Y=[params.Y0|default(-1)|float, params.Y1|default(-1)|float] %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_BED_MESH" MSG="idex_mode: {idex_mode}, X: {X}, Y: {Y}"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is not defined %}
	{% set zero_ref_pos = [safe_home_x if actual_true_zero_position_x is none else actual_true_zero_position_x, safe_home_y if actual_true_zero_position_y is none else actual_true_zero_position_y] %}
	{% endif %}
	
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	
	
	
	
	{% set X=[0, printable_x_max] %}
	{% endif %}
	
	
	{% set beacon_bed_mesh_scv = printer["gcode_macro RatOS"].beacon_bed_mesh_scv|default(25)|int %}
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% if printer.fastconfig.settings.beacon is defined and not beacon_contact_bed_mesh %}
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={beacon_bed_mesh_scv}
	{% endif %}
	
	
	{% set default_profile = printer["gcode_macro RatOS"].bed_mesh_profile|default('ratos') %}
	{% if printer["gcode_macro RatOS"].calibrate_bed_mesh|lower == 'true' %}
	BED_MESH_CLEAR
	{% if printer["gcode_macro RatOS"].adaptive_mesh|lower == 'true' %}
	CALIBRATE_ADAPTIVE_MESH PROFILE="{default_profile}" X0={X[0]} X1={X[1]} Y0={Y[0]} Y1={Y[1]} T={params.T|int} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={idex_mode} ZERO_REF_POS_X={zero_ref_pos[0]} ZERO_REF_POS_Y={zero_ref_pos[1]}
	{% else %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	BED_MESH_PROFILE LOAD="{default_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	
	{% elif printer["gcode_macro RatOS"].bed_mesh_profile is defined %}
	BED_MESH_CLEAR
	BED_MESH_PROFILE LOAD="{printer["gcode_macro RatOS"].bed_mesh_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"

[gcode_macro CALIBRATE_ADAPTIVE_MESH]
gcode = 
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set default_profile = params.PROFILE %}
	
	
	{% set x0 = params.X0|default(-1)|float %}
	{% set y0 = params.Y0|default(-1)|float %}
	{% set x1 = params.X1|default(-1)|float %}
	{% set y1 = params.Y1|default(-1)|float %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Received coordinates X0={x0|round(1)} Y0={y0|round(1)} X1={x1|round(1)} Y1={y1|round(1)}"
	
	{% if x0 >= x1 or y0 >= y1 %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Invalid coordinates received. Please check your slicer settings. Falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	
	
	{% if params.ZERO_REF_POS_X is defined and params.ZERO_REF_POS_Y is defined %}
	{% set zero_ref_pos_x = params.ZERO_REF_POS_X|float %}
	{% set zero_ref_pos_y = params.ZERO_REF_POS_Y|float %}
	{% if zero_ref_pos_x < x0 or zero_ref_pos_x > x1 or zero_ref_pos_y < y0 or zero_ref_pos_y > y1 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Zero reference position X={zero_ref_pos_x|round(1)} Y={zero_ref_pos_y|round(1)} is outside the mesh region, expanding mesh region to include it."
	{% set x0 = [x0, zero_ref_pos_x]|min %}
	{% set y0 = [y0, zero_ref_pos_y]|min %}
	{% set x1 = [x1, zero_ref_pos_x]|max %}
	{% set y1 = [y1, zero_ref_pos_y]|max %}
	{% endif %}
	{% endif %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float %}
	
	
	{% set mesh_x0 = [[x0, max_x]|min, min_x]|max %}
	{% set mesh_y0 = [[y0, max_y]|min, min_y]|max %}
	{% set mesh_x1 = [[x1, max_x]|min, min_x]|max %}
	{% set mesh_y1 = [[y1, max_y]|min, min_y]|max %}
	
	{% if mesh_x0 == min_x and mesh_y0 == min_y and mesh_x1 == max_x and mesh_y1 == max_y %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Print is using the full bed, falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	
	{% set probe_count_x = mesh_config.probe_count.split(",")[0]|int %}
	{% if mesh_config.probe_count.split(",")|length == 2 %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[1]|int %}
	{% else %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[0]|int %}
	{% endif %}
	
	
	{% set probe_x_step = (max_x - min_x) / probe_count_x %}
	{% set probe_y_step = (max_y - min_y) / probe_count_y %}
	
	
	{% set mesh_count_x = ([(mesh_x1 - mesh_x0) / probe_x_step, 3]|max)|int %}
	{% set mesh_count_y = ([(mesh_y1 - mesh_y0) / probe_y_step, 3]|max)|int %}
	{% set min_mesh_count = [mesh_count_x, mesh_count_y]|min %}
	{% set max_mesh_count = [mesh_count_x, mesh_count_y]|max %}
	
	
	{% set algorithm = mesh_config.algorithm %}
	{% if algorithm|lower == 'lagrange' and max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="cannot exceed a probe_count of 6 when using lagrange interpolation. Falling back to bicubic interpolation."
	{% set algorithm = 'bicubic' %}
	{% endif %}
	{% if algorithm|lower == 'bicubic' and min_mesh_count < 4 %}
	{% if max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="invalid probe_count option when using bicubic interpolation. Combination of 3 points on one axis with more than 6 on another is not permitted. Forcing minimum mesh count to be 4."
	{% set min_mesh_count = 4 %}
	{% else %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="bicubic interpolation with a probe_count of less than 4 points detected. Forcing lagrange interpolation."
	{% set algorithm = 'lagrange' %}
	{% endif %}
	{% endif %}
	
	{% set mesh_count_x = ([min_mesh_count, mesh_count_x]|max)|int %}
	{% set mesh_count_x = ([max_mesh_count, mesh_count_x]|min)|int %}
	{% set mesh_count_y = ([min_mesh_count, mesh_count_y]|max)|int %}
	{% set mesh_count_y = ([max_mesh_count, mesh_count_y]|min)|int %}
	
	{% set should_prime = printer["gcode_macro RatOS"].nozzle_priming == 'primeblob' %}
	{% if printer["dual_carriage"] is not defined %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% else %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 != 0 and probe_first %}
	{% set probe_first = false %}
	{% elif printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 == 0 and not probe_first %}
	{% set probe_first = true %}
	{% endif %}
	
	
	{% if should_prime and probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="mesh coordinates X0={mesh_x0|round(1)} Y0={mesh_y0|round(1)} X1={mesh_x1|round(1)} Y1={mesh_y1|round(1)}"
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y} RELATIVE_REFERENCE_INDEX=-1
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	
	
	{% if should_prime and not probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro M84]
rename_existing = M84.1
gcode = 
	
	M84.1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_OFFSET X=0 Y=0
	
	
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro _VAOC"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False
	{% endif %}
	
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	SET_SKEW CLEAR=1
	
	
	_LED_MOTORS_OFF

[gcode_macro M104]
rename_existing = M104.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M104" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set temperature_offset_t0 = printer["gcode_macro T0"].temperature_offset|default(0)|int %}
	{% set temperature_offset_t1 = printer["gcode_macro T1"].temperature_offset|default(0)|int %}
	{% set s0 = [s + temperature_offset_t0, 0]|max %}
	{% set s1 = [s + temperature_offset_t1, 0]|max %}
	{% if temperature_offset_t0 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t0}°C added to toolhead T0."
	{% endif %}
	{% if temperature_offset_t1 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t1}°C added to toolhead T1."
	{% endif %}
	{% else %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	M104.1 S{s0} T0
	M104.1 S{s1} T1
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% else %}
	M104.1 S{s} T{t}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M109]
rename_existing = M109.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M109" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M109" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	M109.1 S{s} T{t}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro SET_HEATER_TEMPERATURE]
rename_existing = SET_HEATER_TEMPERATURE_BASE
gcode = 
	
	{% set heater = params.HEATER|default("") %}
	{% set target = params.TARGET|default(0)|int %}
	
	DEBUG_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="heater: {heater}, target: {target}"
	
	{% set t = -1 %}
	{% if heater|lower == "extruder" or heater|lower == "extruder1" %}
	
	{% set t = 0 if heater|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and target > 0 %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set target = [target + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE_BASE HEATER="{heater}" TARGET={target}
	
	{% if t != -1 and printer.fastconfig.settings.beacon is defined %}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro TEMPERATURE_WAIT]
rename_existing = TEMPERATURE_WAIT_BASE
gcode = 
	
	{% set sensor = params.SENSOR|default("") %}
	{% set minimum = params.MINIMUM|default(-1)|int %}
	{% set maximum = params.MAXIMUM|default(-1)|int %}
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="sensor: {sensor}, minimum: {minimum}, maximum: {maximum}"
	
	{% set t = -1 %}
	{% if sensor|lower == "extruder" or sensor|lower == "extruder1" %}
	
	{% set t = 0 if sensor|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and (minimum > 0 or maximum > 0) %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% if minimum > -1 %}
	{% set minimum = [minimum + temperature_offset, 0]|max %}
	{% endif %}
	{% if maximum > -1 %}
	{% set maximum = [maximum + temperature_offset, 0]|max %}
	{% endif %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set id = "sensor " ~ sensor if t == -1 else "toolhead T" ~ t %}
	
	
	{% if minimum > -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum} MAXIMUM={maximum}
	{% elif minimum > -1 and maximum == -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum}
	{% elif minimum == -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MAXIMUM={maximum}
	{% else %}
	
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="neither MINIMUM or MAXIMUM args were specified, call TEMPERATURE_WAIT_BASE is expected to fail"
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}"
	{% endif %}
	
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature for {id} reached."

[gcode_macro SDCARD_PRINT_FILE]
rename_existing = SDCARD_PRINT_FILE_BASE
gcode = 
	{% if printer["ratos"] is defined %}
	PROCESS_GCODE_FILE { rawparams }
	{% else %}
	SDCARD_PRINT_FILE_BASE { rawparams }
	{% endif %}

[gcode_macro SKEW_PROFILE]
rename_existing = SKEW_PROFILE_BASE
variable_loaded_profile = ""
gcode = 
	{% if params.LOAD is defined %}
	{% if printer.fastconfig.settings["skew_correction %s" % params.LOAD] is defined %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='"{params.LOAD}"'
	{% endif %}
	{% endif %}
	
	SKEW_PROFILE_BASE { rawparams }

[gcode_macro SET_SKEW]
rename_existing = SET_SKEW_BASE
gcode = 
	{% if params.CLEAR is defined %}
	{% if params.CLEAR|default(0)|int == 1 %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='""'
	{% endif %}
	{% endif %}
	
	SET_SKEW_BASE { rawparams }

[gcode_macro SET_VELOCITY_LIMIT]
rename_existing = SET_VELOCITY_LIMIT_BASE
gcode = 
	{% if params.ACCEL_TO_DECEL is defined %}
	
	{% if params.ACCEL is defined %}
	{% set accel = params.ACCEL|float %}
	{% else %}
	{% set accel = printer.toolhead.max_accel|float %}
	{% endif %}
	
	{% if params.VELOCITY is defined %}
	{% set velocity = params.VELOCITY|float %}
	{% else %}
	{% set velocity = printer.toolhead.max_velocity|float %}
	{% endif %}
	
	{% if params.SQUARE_CORNER_VELOCITY is defined %}
	{% set scv = params.SQUARE_CORNER_VELOCITY|float %}
	{% else %}
	{% set scv = printer.toolhead.square_corner_velocity|float %}
	{% endif %}
	
	{% set mcr = params.ACCEL_TO_DECEL|float / accel %}
	
	DEBUG_ECHO PREFIX="SET_VELOCITY_LIMIT" MSG="ACCEL={accel}, VELOCITY={velocity}, SQUARE_CORNER_VELOCITY={scv}, MINIMUM_CRUISE_RATIO={mcr}"
	
	SET_VELOCITY_LIMIT_BASE ACCEL={accel} VELOCITY={velocity} SQUARE_CORNER_VELOCITY={scv} MINIMUM_CRUISE_RATIO={1-mcr}
	
	{% else %}
	
	SET_VELOCITY_LIMIT_BASE { rawparams }
	
	{% endif %}

[gcode_macro BED_MESH_CALIBRATE]
rename_existing = _BED_MESH_CALIBRATE_BASE
variable_abl_and_home_z_if_required = True
gcode = 
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	{% if abl_and_home_z_if_required %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% endif %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set beacon_default_probe_method = printer.fastconfig.settings.beacon.default_probe_method|default('proximity') %}
	{% set probe_method = params.PROBE_METHOD|default(beacon_default_probe_method)|lower %}
	{% if probe_method == 'proximity' %}
	_CHECK_ACTIVE_BEACON_MODEL_TEMP TITLE="Bed mesh calibration warning"
	{% endif %}
	{% endif %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_BED_MESH_CALIBRATE_BASE {rawparams}
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	_APPLY_RATOS_BED_MESH_PARAMETERS {rawparams}
	{% endif %}

[gcode_macro SET_GCODE_OFFSET]
rename_existing = SET_GCODE_OFFSET_BASE
gcode = 
	DEBUG_ECHO PREFIX="SET_GCODE_OFFSET" MSG="{rawparams|replace('"', '')|replace("'", '')}"
	{% set z_before = printer.gcode_move.homing_origin.z|float %}
	SET_GCODE_OFFSET_BASE {rawparams}
	_AFTER_SET_GCODE_OFFSET Z_BEFORE={z_before}

[gcode_macro _AFTER_SET_GCODE_OFFSET]
gcode = 
	{% set z_before = params.Z_BEFORE|float %}
	{% set z_after = printer.gcode_move.homing_origin.z|float %}
	{% if z_before != z_after %}
	_ALERT_NON_ZERO_Z_OFFSET FORCE=1
	{% endif %}

[gcode_macro _START_PRINT_PARK]
gcode = 
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_x = printer["gcode_macro RatOS"].start_print_park_x %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% if printer["gcode_macro RatOS"].start_print_park_x is defined and printer["gcode_macro RatOS"].start_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="start_print_park_x is ignored for IDEX printers"
	{% endif %}
	PARK_TOOLHEAD
	G90
	{% endif %}
	
	
	_PARK LOCATION={start_print_park_in} X={start_print_park_x}
	G0 Z{z} F{z_speed}

[gcode_macro _END_PRINT_PARK]
gcode = 
	{% if printer["dual_carriage"] is defined %}
	
	{% if printer["gcode_macro RatOS"].end_print_park_x is defined and printer["gcode_macro RatOS"].end_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="end_print_park_x is ignored for IDEX printers"
	{% endif %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	PARK_TOOLHEAD
	G90
	{% endif %}
	_PARK LOCATION={printer["gcode_macro RatOS"].end_print_park_in} X={printer["gcode_macro RatOS"].end_print_park_x}

[gcode_macro _PARK]
gcode = 
	
	{% set x = params.X %}
	{% set location = params.LOCATION|default('back')|lower %}
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	{% set nozzle_priming = printer["gcode_macro RatOS"].nozzle_priming|lower %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="park"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% if x != '' %}
	{% if x|float >= printer.toolhead.axis_minimum.x + 5 and x|float <= printable_x_max - 5 %}
	{% set park_x = x|float %}
	{% else %}
	{action_respond_info('The requested X co-ordinate is outside the defined axis bounds - using defaults')}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	{% else %}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	
	
	{% set park_y = printable_y_max - 15 %}
	{% if location == 'front' %}
	{% set park_y = printer.toolhead.axis_minimum.y + 5 %}
	{% elif location == 'center' %}
	{% set park_y = printable_y_max / 2 %}
	{% elif location == 'primeblob' and printer["dual_carriage"] is defined %}
	
	{% set park_y = printable_y_max - 15 %}
	{% endif %}
	
	
	{% if location == 'primeblob' and printer["dual_carriage"] is not defined %}
	{% if (nozzle_priming == 'primeblob' or nozzle_priming == 'primeline') %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set park_x = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set park_x = printable_x_max - 5 %}
	{% else %}
	{% set park_x = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set park_y = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set park_y = printable_y_max - 5 %}
	{% else %}
	{% set park_y = nozzle_prime_start_y|float %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	G0 X{park_x} Y{park_y} F{speed}
	{% else %}
	
	G0 Y{park_y} F{speed}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="park"

[gcode_macro SAVE_PROBE_RESULT]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	{% set last_z_offset = 9999.9 %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if beacon_contact_prime_probing %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	{% else %}
	{% set last_z_offset = printer.beacon.last_sample.dist - current_z %}
	{% endif %}
	{% elif printer.fastconfig.settings.bltouch is defined  %}
	{% set config_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% elif printer.fastconfig.settings.probe is defined  %}
	{% set config_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% endif %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Saving offset adjustment of {last_z_offset} in {params.VARIABLE|default('last_z_offset')}"
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={params.VARIABLE|default('last_z_offset')} VALUE={last_z_offset}

[gcode_macro PROBE_FOR_PRIMING]
gcode = 
	
	{% set probe_for_priming_disable_mesh_constraints = true if printer["gcode_macro RatOS"].probe_for_priming_disable_mesh_constraints|default(false)|lower == 'true' else false %}
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower != 'false' %}
	SAVE_GCODE_STATE NAME=probe_for_priming_state
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the prime location.."
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set t = params.TOOLHEAD|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% if idex_mode == '' %}
	
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% if t == 0 %}
	{% set x_start = 5 %}
	{% else %}
	{% set x_start = printable_x_max - 5 %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% endif %}
	{% endif %}
	{% set z = printer.fastconfig.settings.bed_mesh.horizontal_move_z|float %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% if printer.fastconfig.settings.bltouch is defined %}
	{% set x_offset = printer.fastconfig.settings.bltouch.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.bltouch.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% elif printer.fastconfig.settings.probe is defined %}
	{% set x_offset = printer.fastconfig.settings.probe.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.probe.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% elif printer.fastconfig.settings.beacon is defined %}
	{% set x_offset = printer.fastconfig.settings.beacon.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.beacon.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.beacon.trigger_distance|float %}
	{% else %}
	{ action_raise_error("No probe, beacon or bltouch section found. Adaptive priming only works with a [probe], [beacon] or [bltouch] section defined.") }
	{% endif %}
	
	{% if z < z_offset %}
	{ action_raise_error("Horizontal move Z ({z}) is below your probe's Z offset ({z_offset}). Please adjust your horizontal_move_z setting in [bed_mesh] to be above {z}.") }
	{% endif %}
	
	{% if not probe_for_priming_disable_mesh_constraints %}
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float - x_offset %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float - y_offset %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float - x_offset %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float - y_offset %}
	
	
	{% set x_start = [[x_start, max_x]|min, min_x]|max %}
	{% set y_start = [[y_start, max_y]|min, min_y]|max %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the start of the prime location at {x_start}, {y_start}"
	
	G90
	
	M83
	
	G0 Z{z} F{z_speed}
	
	G1 X{x_start} Y{y_start} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result
	{% endif %}
	
	{% if idex_mode == '' %}
	
	{% set x_end = x_start %}
	{% set y_end = y_start + 45 %}
	{% else %}
	
	{% if t==1 %}
	{% set x_end = x_start - 45 %}
	{% else %}
	{% set x_end = x_start + 45 %}
	{% endif %}
	{% set y_end = y_start %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the end of the prime location at {x_end}, {y_end}"
	G1 X{x_end} Y{y_end} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result
	{% endif %}
	
	RESTORE_GCODE_STATE NAME=probe_for_priming_state
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	{% endif %}

[gcode_macro RESET_PRIME_PROBE_STATE]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result VALUE=None
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result_t1 VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result_t1 VALUE=None
	{% endif %}

[gcode_macro PROBE_CURRENT_POSITION]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	SAVE_GCODE_STATE NAME=probe_current_position_state
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	ASSERT_PROBE_DEPLOYED
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_prime_probing %}
	PROBE PROBE_METHOD=contact SAMPLES=1
	{% else %}
	PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	BEACON_QUERY
	{% else %}
	
	RESTORE_GCODE_STATE NAME=probe_current_position_state MOVE=1 MOVE_SPEED={printer["gcode_macro RatOS"].macro_z_speed|float}
	{% endif %}

[gcode_macro PRIME_BLOB]
description = Prints a primeblob, used internally, if configured, as part of the START_PRINT macro.
variable_x_offset = 5
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="prime_blob"
	SET_MACRO_TRAVEL_SETTINGS
	
	RATOS_ECHO PREFIX="Priming" MSG="Priming nozzle with prime blob.."
	
	
	{% set current_toolhead = 0 %}
	
	
	{% set target_idex_mode = '' %}
	{% set extruder = 'extruder' %}
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE is defined %}
	{% set target_idex_mode = params.IDEX_MODE|default('')|lower %}
	{% else %}
	{ action_raise_error("IDEX_MODE parameter not found for PRIME_BLOB macro. This is likely a bug.") }
	{% endif %}
	RATOS_ECHO PREFIX="Priming" MSG="Priming in IDEX {target_idex_mode} mode.."
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set current_toolhead = 1 if current_idex_mode=='primary' else 0 %}
	{% set extruder = 'extruder1' if current_toolhead == 1 else 'extruder' %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	SAVE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set fan_speed = printer["gcode_macro RatOS"].nozzle_prime_bridge_fan|float %}
	{% set nozzle_diameter = printer.fastconfig.settings[extruder].nozzle_diameter|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set has_start_offset_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) != 9999.9 %}
	{% if printer["dual_carriage"] is defined %}
	{% set has_start_offset_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) != 9999.9 %}
	{% endif %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_z_height = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set nozzle_prime_direction = printer["gcode_macro RatOS"].nozzle_prime_direction|lower %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% if target_idex_mode == '' %}
	
	{% set x_factor = 0 %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% set y_factor = -1 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% if nozzle_prime_start_y|float < printable_y_max / 2 %}
	{% set y_factor = 1 %}
	{% else %}
	{% set y_factor = -1 %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_direction == 'forwards' %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_direction == 'backwards' %}
	{% set y_factor = -1 %}
	{% endif %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% else %}
	{% set z = start_print_park_z_height %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% set y_factor = 0 %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set x_start = center_x / 2 + 5 %}
	{% set x_factor = 1 %}
	{% else %}
	
	
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% if current_toolhead == 0 %}
	{% set x_start = 55 %}
	{% set x_factor = -1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 55 %}
	{% set x_factor = 1 %}
	{% endif %}
	{% else %}
	{% if current_toolhead == 0 %}
	{% set x_start = 5 %}
	{% set x_factor = 1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 5 %}
	{% set x_factor = -1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_x_max - 5 %}
	{% endif %}
	{% set z = 10 %}
	{% endif %}
	
	{% set start_z_offset = 0 %}
	{% set end_z_offset = 0 %}
	{% if has_start_offset_t0 %}
	{% set start_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) %}
	{% set end_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_end_result|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t0) ) }
	{% endif %}
	{% if end_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t0) )  }
	{% endif %}
	{% set start_z_offset = start_z_probe_result_t0 %}
	{% set end_z_offset = end_z_probe_result_t0 %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	{% if current_toolhead == 1 or both_toolheads or target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	{% if has_start_offset_t1 %}
	{% set start_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) %}
	{% set end_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_end_result_t1|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t1) ) }
	{% endif %}
	{% if end_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t1) ) }
	{% endif %}
	{% set start_z_offset = [start_z_offset, start_z_probe_result_t1]|max %}
	{% set end_z_offset = [end_z_offset, start_z_probe_result_t1]|max %}
	{% endif %}
	{% endif %}
	{% if target_idex_mode != 'copy' and target_idex_mode != 'mirror' %}
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% set original_start_z_offset = start_z_offset %}
	{% set original_end_z_offset = end_z_offset %}
	{% set start_z_offset = original_end_z_offset %}
	{% set end_z_offset = original_start_z_offset %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	DEBUG_ECHO PREFIX="PRIME_BLOB" MSG="x_start: {x_start}, y_start: {y_start}, x_factor: {x_factor}, y_factor: {y_factor}, z: {z}, start_z_offset: {start_z_offset}, end_z_offset: {end_z_offset}"
	
	
	G90
	
	M83
	RATOS_ECHO PREFIX="Priming" MSG="Lifting Z to {z}.."
	
	G0 Z{z} F{z_speed}
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% if start_print_park_in != 'primeblob' %}
	G1 X{x_start} F{speed}
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% endif %}
	{% else %}
	
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% if target_idex_mode=="copy" or target_idex_mode=="mirror" %}
	RATOS_ECHO PREFIX="Priming" MSG="Mirroring move to {x_start}, {y_start} along the edge of the print area.."
	
	_IDEX_MIRROR PRIMING=1
	{% else %}
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% endif %}
	G1 X{x_start} F{speed}
	{% endif %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Starting prime blob.."
	
	G1 Z{0.5 + start_z_offset} F{z_speed}
	
	G1 Y{y_start} F{speed}
	
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	
	M106 S{fan_speed}
	
	G1 Z5 F100 E5
	G92 E0
	RATOS_ECHO PREFIX="Priming" MSG="Bridging with {((fan_speed/255) * 100)|int}% fan speed.."
	
	G1 F3000 X{x_start + (15 * x_factor)} Y{y_start + (15 * y_factor)} E{1 / ((0.4 / nozzle_diameter) ** 2)}
	
	
	
	G1 F3000 X{x_start + (20 * x_factor)} Y{y_start + (20 * y_factor)} Z{3.8 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (34 * x_factor)} Y{y_start + (34 * y_factor)} Z{2.6 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (38 * x_factor)} Y{y_start + (38 * y_factor)} Z{1.4 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (42 * x_factor)} Y{y_start + (42 * y_factor)} Z{0.2 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	
	M106 S0
	
	G1 F3000 X{x_start + (46 * x_factor)} Y{y_start + (46 * y_factor)} Z{0.2 + end_z_offset} E0.6
	
	G1 F{speed} X{x_start + (50 * x_factor)} Y{y_start + (50 * y_factor)}
	
	
	{% if target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if target_idex_mode == "copy" %}
	{% if first_y >= 0 %}
	_IDEX_COPY DANCE=0 Y={first_y}
	{% else %}
	_IDEX_COPY DANCE=0 Y={params.Y1}
	{% endif %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	RESTORE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="prime_blob"
	
	
	G92 E0

[gcode_macro UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set temp = params.TEMP|default(220)|int %}
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_UNLOAD_FILAMENT TEMP={temp} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_UNLOAD_FILAMENT]
description = Unload filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_UNLOAD_FILAMENT" MSG="TEMP: {temp}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=unload_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	G4 P3000
	
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD=0 NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=unload_state
	
	
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament unloading completed"

[gcode_macro _IDEX_UNLOAD_FILAMENT]
description = Unload filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading T{toolhead} filament..."
	
	DEBUG_ECHO PREFIX="_IDEX_UNLOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} AUTOMATED={automated}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="T{toolhead} filament unloading completed"

[gcode_macro _UNLOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LEGACY_UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
gcode = 
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set unload_speed = 5 * 60 %}
	{% set unload_length = printer["gcode_macro RatOS"].filament_unload_length|float %}
	M117 Unloading filament...
	
	G0 E10 F300
	
	G0 E-5 F3600
	
	G4 P3000
	
	G0 E5 F6000
	
	G0 E-15 F6000
	
	G0 E-{unload_length} F{unload_speed}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}
	M117 Filament unloaded!
	RESPOND MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	RATOS_ECHO MSG="Unloading filament from nozzle to cooling zone... Please wait!"
	
	_PURGE_BEFORE_UNLOAD TOOLHEAD={toolhead}
	
	{% if printer["gcode_macro _UNLOAD_WITHOUT_TIP_FORMING"] is defined %}
	
	_UNLOAD_WITHOUT_TIP_FORMING TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	_UNLOAD_WITH_TIP_FORMING NAME='{filament_name}' TYPE='{filament_type}'
	{% endif %}
	
	G4 P3000

[gcode_macro _UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	{% set tooolhead_sensor_to_extruder_gear_distance = printer["gcode_macro T%s" % toolhead].tooolhead_sensor_to_extruder_gear_distance|float %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER" MSG="TOOLHEAD: {toolhead}"
	
	
	G0 E-{extruder_gear_to_cooling_position_distance + tooolhead_sensor_to_extruder_gear_distance + 50} F{extruder_load_speed}
	
	RATOS_ECHO MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_WITH_TIP_FORMING]
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	{% if filament_name != '' and filament_type != '' %}
	_UNLOAD_KNOWN_FILAMENT NAME={filament_name} TYPE={filament_type}
	{% else %}
	_UNLOAD_UNKNOWN_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _UNLOAD_KNOWN_FILAMENT]
description = User overrideable tip forming macro if slicer filament profiles are known
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	RATOS_ECHO PREFIX="FILAMENT TYPE" MSG='{filament_type}'
	RATOS_ECHO PREFIX="FILAMENT PROFILE" MSG='{filament_name}'
	
	
	{% if filament_name == "Prusament PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% elif filament_name == "Nobufil PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% else %}
	
	RATOS_ECHO PREFIX="_UNLOAD_KNOWN_FILAMENT" MSG="Filament profile not found!"
	_UNLOAD_UNKNOWN_FILAMENT
	{% endif %}

[gcode_macro _UNLOAD_UNKNOWN_FILAMENT]
description = User overrideable standard tip forming macro
gcode = 
	
	DEBUG_ECHO PREFIX="_UNLOAD_UNKNOWN_FILAMENT" MSG="Using standard tip forming macro!"
	
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10

[gcode_macro _TIP_FORMING]
gcode = 
	
	{% set cooling_moves = params.COOLING_MOVES|default(4)|int %}
	{% set cooling_move_length = params.COOLING_MOVE_LENGTH|default(10)|float %}
	{% set start_cooling_speed = params.START_COOLING_SPEED|default(10)|float * 60 %}
	{% set end_cooling_speed = params.END_COOLING_SPEED|default(50)|float * 60 %}
	{% if cooling_moves == 0 %}
	{% set cooling_move_length = 0 %}
	{% endif %}
	
	
	{% set dip = true if params.DIP|default(false)|lower == "true" else false %}
	{% set dip_length = params.DIP_LENGTH|default(22)|float %}
	{% set dip_speed = params.DIP_SPEED|default(30)|float * 60 %}
	{% set dip_retract_speed = params.DIP_RETRACT_SPEED|default(70)|float * 60 %}
	
	
	{% set retract_length = params.RETRACT_LENGTH|default(18)|float %}
	{% set start_retract_speed = params.START_RETRACT_SPEED|default(120)|float * 60 %}
	{% set end_retract_speed = params.END_RETRACT_SPEED|default(20)|float * 60 %}
	
	DEBUG_ECHO PREFIX="_TIP_FORMING" MSG="cooling_moves: {cooling_moves}, cooling_move_length: {cooling_move_length}, start_cooling_speed: {start_cooling_speed}, end_cooling_speed: {end_cooling_speed}, dip: {dip}, dip_length: {dip_length}, dip_speed: {dip_speed}, dip_retract_speed: {dip_retract_speed}, retract_length: {retract_length}, start_retract_speed: {start_retract_speed}, end_retract_speed: {end_retract_speed}"
	
	M220 S100
	
	
	G92 E0
	{% set retract = retract_length + cooling_move_length / 2 - 15 %}
	G1 E-15 F{start_retract_speed}
	G1 E-{0.7 * retract} F{1.0 * end_retract_speed}
	G1 E-{0.2 * retract} F{0.5 * end_retract_speed}
	G1 E-{0.1 * retract} F{0.3 * end_retract_speed}
	
	
	G92 E0
	{% if cooling_moves > 0 %}
	{% set i = (end_cooling_speed - start_cooling_speed) / (2 * cooling_moves - 1) %}
	{% for m in range(cooling_moves) %}
	G1 E{cooling_move_length} F{(start_cooling_speed + i * m * 2)}
	G1 E-{cooling_move_length} F{(start_cooling_speed + i * (m * 2 + 1))}
	{% endfor %}
	{% endif %}
	
	
	G92 E0
	{% if dip %}
	G1 E{dip_length} F{dip_speed}
	G4 P100
	G1 E-{dip_length} F{dip_retract_speed}
	{% endif %}
	
	G92 E0
	M400

[delayed_gcode __ON_FILAMENT_SENSOR_BUTTON_PRESSED_STARTUP_GUARD]
initial_duration = 2.
gcode = 
	SET_GCODE_VARIABLE MACRO=_ON_FILAMENT_SENSOR_BUTTON_PRESSED VARIABLE=startup_complete VALUE=True

[gcode_macro _ON_FILAMENT_SENSOR_BUTTON_PRESSED]
variable_startup_complete = False
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set toolhead_sensor_button_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_sensor_button_only_when_sensor_enabled|default(false)|lower == 'true' %}
	
	
	{% if not startup_complete and sensor_enabled %}
	{action_emergency_stop("RatOS: The T%s filament sensor button was triggered immediately on printer startup. This is likely a false trigger. Please check your filament sensor wiring and configuration!" % (toolhead,))}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_SENSOR_BUTTON_PRESSED" MSG="TOOLHEAD: {toolhead}, SENSOR_ENABLED: {sensor_enabled}, TOOLHEAD_SENSOR_BUTTON_ONLY_WHEN_SENSOR_ENABLED: {toolhead_sensor_button_only_when_sensor_enabled}"
	
	{% if not printer.virtual_sdcard.is_active and (sensor_enabled or not toolhead_sensor_button_only_when_sensor_enabled) %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	{% set toolhead_detect_clog_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_detect_clog_only_when_sensor_enabled|default(true)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}, ENABLE_CLOG_DETECTION: {enable_clog_detection}, TOOLHEAD_DETECT_CLOG_ONLY_WHEN_SENSOR_ENABLED: {toolhead_detect_clog_only_when_sensor_enabled}, SENSOR_ENABLED: {sensor_enabled}"
	
	{% if enable_clog_detection and (sensor_enabled or not toolhead_detect_clog_only_when_sensor_enabled) %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_clog_detection %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_FILAMENT_END]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set clogged = true if params.CLOGGED|default(false)|lower == 'true' else false %}
	
	
	{% set unload_after_runout = printer["gcode_macro T%s" % toolhead].unload_after_runout|float %}
	
	
	{% if clogged %}
	_LED_FILAMENT_CLOG TOOLHEAD={toolhead}
	{% else %}
	_LED_FILAMENT_RUNOUT TOOLHEAD={toolhead}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_END" MSG="TOOLHEAD: {toolhead}"
	
	{% if printer.virtual_sdcard.is_active %}
	{% if not printer.pause_resume.is_paused %}
	PAUSE RUNOUT=True
	{% endif %}
	{% if not clogged and unload_after_runout %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	{% if not clogged and printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true'%}
	_JOIN_SPOOL TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M600]
description = Executes a color change by pausing the printer an unloading the filament.
gcode = 
	PAUSE
	UNLOAD_FILAMENT AUTOMATED=True
	RATOS_ECHO MSG="Please load new filament and resume"

[gcode_macro COLD_PULL]
description = Automated hotend cold pull.
gcode = 
	
	{% set extrusion_temp = params.EXTRUSION_TEMP|default(220)|int %}
	{% set cold_pull_temp = params.COLD_PULL_TEMP|default(80)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	
	{% if printer["dual_carriage"] is not defined %}
	{% set toolhead = 0 %}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead != 0 and toolhead != 1 %}
	{action_raise_error("Please select toolhead! 0 = left, 1 = right toolhead")}
	{% endif %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	RATOS_ECHO MSG="Starting cold pull on T{toolhead}..."
	{% else %}
	RATOS_ECHO MSG="Starting cold pull..."
	{% endif %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	SAVE_GCODE_STATE NAME=cold_pull_state
	
	
	{% if printer["dual_carriage"] is defined and "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	RATOS_ECHO MSG="Heating T{toolhead} to {extrusion_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={extrusion_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={extrusion_temp} MAXIMUM={extrusion_temp + 2}
	
	
	G4 P3000
	
	
	RATOS_ECHO MSG="extruding..."
	G92 E0
	G1 E30 F300
	G92 E0
	
	
	RATOS_ECHO MSG="Cooling T{toolhead} to {cold_pull_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={cold_pull_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={cold_pull_temp} MAXIMUM={cold_pull_temp + 2}
	
	
	G4 P10000
	
	
	RATOS_ECHO MSG="cold pull..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-40 VELOCITY=5 ACCEL=100
	
	
	RATOS_ECHO MSG="eject filament..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-200 VELOCITY=20 ACCEL=500
	
	
	RATOS_ECHO MSG="cooling down extruder..."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	RESTORE_GCODE_STATE NAME=cold_pull_state
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	
	CONSOLE_ECHO TITLE="Cold pull complete" MSG="Please remove the filament from the PTFE tube and cut the end off. Do NOT try to load it again." TYPE="warning"

[gcode_macro _USER_START_PRINT_BEFORE_HOMING]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_BED]
gcode = 

[gcode_macro _USER_START_PRINT_BED_MESH]
gcode = 

[gcode_macro _USER_START_PRINT_PARK]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 

[gcode_macro _USER_START_PRINT_HEAT_CHAMBER]
description = Uses the extruder sensor to wait for chamber temp. Override the _START_PRINT_HEAT_CHAMBER macro to implement heated chamber handling.
gcode = 
	
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}

[gcode_macro _USER_END_PRINT_BEFORE_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_AFTER_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_PARK]
gcode = 

[gcode_macro _USER_END_PRINT_FINISHED]
description = User hook for when the print is finished after gcode state has been restored.
gcode = 

[gcode_macro _USER_START_PRINT]
gcode = 

[gcode_macro _USER_END_START_PRINT]
gcode = 

[gcode_macro _USER_START_FEATURE]
gcode = 

[gcode_macro _USER_END_FEATURE]
gcode = 

[gcode_macro _USER_BEFORE_IDLE_TIMEOUT]
gcode = 

[gcode_macro _USER_AFTER_IDLE_TIMEOUT]
gcode = 

[gcode_macro ECHO_T_VARS]
description = Echo Toolhead variables to the console.
gcode = 
	{% set t = params.T|default(0) %}
	RATOS_ECHO MSG="T{t} Variables"
	{% for var, value in printer["gcode_macro T%s" % t].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ECHO_RATOS_VARS]
description = Echo RatOS variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro RatOS"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ENSURE_CRITICAL_RATOS_INIT]
variable_completed = False
gcode = 
	{% if not completed %}
	CALCULATE_PRINTABLE_AREA
	SET_GCODE_VARIABLE MACRO=ENSURE_CRITICAL_RATOS_INIT VARIABLE=completed VALUE=True
	{% endif %}

[delayed_gcode RATOS_INIT]
initial_duration = 0.1
gcode = 
	{action_respond_info("Initializing RatOS...")}
	ENSURE_CRITICAL_RATOS_INIT
	_LED_STANDBY
	INITIAL_FRONTEND_UPDATE
	_CHAMBER_FILTER_SANITY_CHECK
	{% if printer.fastconfig.settings.beacon is defined %}
	
	_BED_MESH_SANITY_CHECK
	{% endif %}
	{% set svv = printer.save_variables.variables %}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=0 C={svv.nozzle_expansion_coefficient_t0|default(0.06)|float}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=1 C={svv.nozzle_expansion_coefficient_t1|default(0.06)|float}
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=idex_applied_offset

[delayed_gcode RATOS_LOGO]
initial_duration = 2
gcode = 
	
	
	
	
	
	ENSURE_CRITICAL_RATOS_INIT
	HELLO_RATOS
	_ALERT_NON_ZERO_Z_OFFSET

[gcode_macro _ALERT_NON_ZERO_Z_OFFSET]
gcode = 
	{% set force = params.FORCE|default(0)|int == 1 %}
	{% set user_offset = printer.named_offsets.user_probe_z_offset.z|float %}
	{% set gcode_offset = printer.gcode_move.homing_origin.z|float %}
	{% set combined_offset = user_offset + gcode_offset %}
	
	{% if force or user_offset != 0 or gcode_offset != 0 %}
	{% set title = "User-adjusted Z-offset of %.3f mm is active" % combined_offset %}
	{% set msg = "" %}
	{% set nl = "" %}
	{% if user_offset != 0 %}
	{% set msg = msg + "beacon true zero user Z-offset: %.3f mm (to clear, use Z_OFFSET_APPLY_PROBE CLEAR=1)" % user_offset %}
	{% set nl = "_N_" %}
	{% endif %}
	{% if gcode_offset != 0 %}
	{% set msg = msg + nl + "G-code Z-offset: %.3f mm" % gcode_offset %}
	{% endif %}
	CONSOLE_ECHO TITLE="{title}" TYPE="info" MSG="{msg}"
	{% endif %}

[gcode_macro _INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE]
gcode = 
	{% set variable = params.VARIABLE|string %}
	{% set svv = printer.save_variables.variables %}
	{% set nlu_msg = "no longer used, please remove" %}
	{% if svv[variable] is defined %}
	{% set v = svv[variable]|string|replace('"', '')|replace("'", "") %}
	{% if not nlu_msg in v %}
	SAVE_VARIABLE VARIABLE={variable} VALUE='"{nlu_msg} (was {v})"'
	{% endif %}
	CONSOLE_ECHO TITLE="Deprecated ratos-variables.cfg variable" TYPE="warning" MSG="The variable {variable} is no longer used, please remove it from your ratos-variables.cfg file."
	{% endif %}

[gcode_macro _NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK]
gcode = 
	
	
	
	
	
	
	
	{% set t = params.T|int %}
	{% set c = params.C|float %}
	{% set normal_low = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_low|default(0.05)|float %}
	{% set normal_high = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_high|default(0.10)|float %}
	
	{% if c < 0 %}
	
	{action_emergency_stop("Invalid nozzle_expansion_coefficient_t%s value in ratos-variables.cfg: %.3f. It must be non-negative." % (t, c))}
	{% endif %}
	{% if c >= normal_high %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite high. Please verify that this is correct."
	{% endif %}
	{% if c <= normal_low %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite low. Please verify that this is correct."
	{% endif %}

[gcode_macro INITIAL_FRONTEND_UPDATE]
gcode = 
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_error = printer["gcode_macro RatOS"].status_color_error|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_unknown}"'
	{% endif %}
	
	
	{% set t0_sensor = "undefined" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	{% set t0_sensor = "detected" %}
	{% else %}
	{% set t0_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t0_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	{% set t1_sensor = "undefined" %}
	{% if printer["dual_carriage"] is defined and printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	{% set t1_sensor = "detected" %}
	{% else %}
	{% set t1_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t1_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	{% if svv.t0_filament is defined and printer["gcode_macro T0"] is defined %}
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	{% if t0_sensor != "empty" %}
	{% set t0_filament_type = svv.t0_filament[0]|default('')|string %}
	{% set t0_filament_name = svv.t0_filament[1]|default('')|string %}
	{% set t0_filament_temp = svv.t0_filament[2]|default(0)|float %}
	{% if t0_filament_name != '' and t0_filament_type != '' and t0_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{t0_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{t0_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={t0_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}
	{% if svv.t1_filament is defined and printer["gcode_macro T1"] is defined %}
	{% if printer["gcode_macro T1"].filament_name is defined and printer["gcode_macro T1"].filament_type is defined and printer["gcode_macro T1"].filament_temp is defined %}
	{% if t1_sensor != "empty" %}
	{% set t1_filament_type = svv.t1_filament[0]|default('')|string %}
	{% set t1_filament_name = svv.t1_filament[1]|default('')|string %}
	{% set t1_filament_temp = svv.t1_filament[2]|default(0)|float %}
	{% if t1_filament_name != '' and t1_filament_type != '' and t1_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='"{t1_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='"{t1_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE={t1_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t1_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro CALCULATE_PRINTABLE_AREA]
variable_calculated = False
gcode = 
	{% if not calculated %}
	{% set bed_margin_x = printer["gcode_macro RatOS"].bed_margin_x %}
	{% set bed_margin_y = printer["gcode_macro RatOS"].bed_margin_y %}
	
	
	
	{% set tool = 0 if printer["gcode_macro T0"] is not defined or printer["gcode_macro T0"].active else 1 %}
	{% set max_x = printer.toolhead.axis_maximum.x if printer["dual_carriage"] is defined and tool == 0 else printer.toolhead.axis_maximum.x - bed_margin_x[1] %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	
	
	{% set max_x = printer.toolhead.axis_maximum.x %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="printer.toolhead.axis_maximum.x {printer.toolhead.axis_maximum.x}"
	
	{% set max_y = printer.toolhead.axis_maximum.y - bed_margin_y[1]%}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_x_max VALUE={max_x}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_y_max VALUE={max_y}
	SET_GCODE_VARIABLE MACRO=CALCULATE_PRINTABLE_AREA VARIABLE=calculated VALUE=True
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	RATOS_LOG PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	{% endif %}

[gcode_macro CACHE_TOOLHEAD_SETTINGS]
variable_cache = {"global": {"accel": 1000, "ratio": 0.5, "speed": 50, "scv": 5}}
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set dummy = cache.__setitem__(key, {"accel": printer.toolhead.max_accel, "ratio": printer.toolhead.minimum_cruise_ratio, "speed": printer.toolhead.max_velocity, "scv": printer.toolhead.square_corner_velocity}) %}
	SET_GCODE_VARIABLE MACRO=CACHE_TOOLHEAD_SETTINGS VARIABLE=cache VALUE="{cache | pprint | replace("\n", "") | replace("\"", "\\\"")}"
	DEBUG_ECHO PREFIX="CACHE_TOOLHEAD_SETTINGS" MSG="Toolhead settings cached for {key}. {printer.toolhead.max_accel} accel, {printer.toolhead.minimum_cruise_ratio} ratio, {printer.toolhead.max_velocity} velocity, {printer.toolhead.square_corner_velocity} scv."

[gcode_macro RESTORE_TOOLHEAD_SETTINGS]
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set values = printer["gcode_macro CACHE_TOOLHEAD_SETTINGS"].cache.__getitem__(key) %}
	{% if values is not defined or values == 'None' %}
	{ action_raise_error("RESTORE_TOOLHEAD_SETTINGS: Toolhead settings not cached for key '" ~ key ~ "'.") }
	{% endif %}
	SET_VELOCITY_LIMIT ACCEL={values.accel} MINIMUM_CRUISE_RATIO={values.ratio} VELOCITY={values.speed} SQUARE_CORNER_VELOCITY={values.scv}
	DEBUG_ECHO PREFIX="RESTORE_TOOLHEAD_SETTINGS" MSG="Toolhead settings restored. {values.accel} accel, {values.ratio} ratio, {values.speed} velocity, {values.scv} scv."

[gcode_macro SET_MACRO_TRAVEL_SETTINGS]
gcode = 
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float %}
	{% set accel = printer["gcode_macro RatOS"].macro_travel_accel %}
	SET_VELOCITY_LIMIT ACCEL={accel} MINIMUM_CRUISE_RATIO=0.5 VELOCITY={speed} SQUARE_CORNER_VELOCITY={5}
	DEBUG_ECHO PREFIX="SET_MACRO_TRAVEL_SETTINGS" MSG="Macro travel settings set. {accel} accel, {speed} velocity"

[gcode_macro SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% if printer["dual_carriage"] is not defined %}
	
	SET_KINEMATIC_POSITION X={printable_x_max / 2} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	{% else %}
	
	IDEX_SET_CENTER_KINEMATIC_POSITION
	{% endif %}

[gcode_macro IDEX_SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x - (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x + (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY

[gcode_macro VERIFY_HYBRID_INVERTED]
gcode = 
	
	{% set inverted = False %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy is defined and printer.fastconfig.settings.ratos_hybrid_corexy.inverted is defined %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy.inverted|lower == 'true' %}
	{% set inverted = True %}
	{% endif %}
	{% endif %}
	{% if inverted == False %}
	{ action_emergency_stop("ratos_hybrid_corexy NOT INVERTED! Inverted hybrid core-xy bugfix not detected.") }
	{% endif %}

[gcode_macro RATOS_ECHO]
gcode = 
	{% set prefix = "RatOS" %}
	{% set debug = params.DEBUG|default(0)|int %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " | " ~ params.PREFIX %}
	{% endif %}
	{% set prefix = prefix ~ ":" %}
	{% set msg = "" %}
	{% if params.MSG is defined %}
	{% set msg = params.MSG %}
	{% else %}
	{% set msg = "No msg parameter provided (this is a bug or unintended use)." %}
	{% endif %}
	{% if not debug %}
	
	M117 {prefix} {msg}
	{% endif %}
	RATOS_LOG PREFIX="{prefix}" MSG="{msg}"
	{% if not debug %}
	RESPOND PREFIX="{prefix}" MSG="{msg}"
	{% else %}
	CONSOLE_ECHO TITLE="{prefix}" TYPE="debug" MSG="{msg}"
	{% endif %}

[gcode_macro ENABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=True
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=prefix_filter VALUE="'{params.FILTER|default('')|lower}'"
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging enabled."

[gcode_macro DISABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=False
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging disabled."

[gcode_macro DEBUG_ECHO]
variable_enabled = False
variable_prefix_filter = ''
gcode = 
	{% set prefix = "DEBUG" %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " - " ~ params.PREFIX %}
	{% endif %}
	{% if enabled and (prefix_filter|lower == '' or prefix_filter|lower in params.PREFIX|lower) %}
	RATOS_ECHO PREFIX="{prefix}" MSG="{params.MSG}" DEBUG=1
	{% endif %}

[gcode_macro START_FEATURE]
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="Start {params.FEATURE} feature gcode"
	{% set scv = printer.toolhead.square_corner_velocity|int|default(5) %}
	{% set accel = printer.toolhead.max_accel|int|default(10000) %}
	{% set ratio = printer.toolhead.minimum_cruise_ratio|float|default(0.5) %}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="scv" VALUE={scv}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="accel" VALUE={accel}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="ratio" VALUE={ratio}
	_USER_START_FEATURE FEATURE="{params.FEATURE}"

[gcode_macro END_FEATURE]
variable_scv = 5
variable_accel = 10000
variable_ratio = 0.5
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="End {params.FEATURE} feature gcode"
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={scv} ACCEL={accel} MINIMUM_CRUISE_RATIO={ratio}
	_USER_END_FEATURE FEATURE="{params.FEATURE}" SCV={scv} ACCEL={accel} RATIO={ratio}

[gcode_macro _ON_LAYER_CHANGE]
variable_layer_number = 0
description = INTERNAL USE ONLY. Call it from the slicers after layer change custom gcode
gcode = 
	
	{% set layer = params.LAYER|int %}
	
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE={layer}
	SET_PRINT_STATS_INFO CURRENT_LAYER={layer}

[gcode_macro _LEARN_MORE_CALIBRATION]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/calibration" %}
	{% set link_text = "RatOS Calibration Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_CHAMBER_FILTER]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter Control" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_FILAMENT]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/filaments" %}
	{% set link_text = "RatOS Filament Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _CONSOLE_SAVE_CONFIG]
gcode = 
	M118 Click <a class="command text--blue">SAVE_CONFIG</a> to save the settings to your printer.cfg.

[gcode_macro _LOAD_RATOS_SKEW_PROFILE]
gcode = 
	{% set ratos_skew_profile = printer["gcode_macro RatOS"].skew_profile|default("") %}
	{% if ratos_skew_profile != "" %}
	{% if printer.fastconfig.config["skew_correction %s" % ratos_skew_profile] is defined %}
	SKEW_PROFILE LOAD={ratos_skew_profile}
	GET_CURRENT_SKEW
	{% else %}
	{% set line_1 = '"Could not find skew profile %s!_N_Clearing skew correction."' % ratos_skew_profile %}
	CONSOLE_ECHO TITLE="Missing skew profile!" TYPE="warning" MSG={line_1}
	SET_SKEW CLEAR=1
	{% endif %}
	{% endif %}

[gcode_macro M601]
gcode = 
	PAUSE

[gcode_macro _STOP_AND_RAISE_ERROR]
gcode = 
	M84
	_RAISE_ERROR MSG="{params.MSG}"

[gcode_macro _RESET_GCODE_VARIABLES]
description = Reset specified [gcode_macro ...] variables to their original values from configuration when Klipper started.
	- MACRO: Name of the GCODE macro containing the variables to reset.
	- VARIABLES: Comma-separated list of variable names to reset (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- QUIET: (optional) If true, suppresses console echo messages for each reset variable. Default is false.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set quiet = params.QUIET|default("false")|lower in ("true", "1", "yes") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	{% set settings = printer.fastconfig.settings[obj_name|lower] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro %s]" % macro) }
	{% endif %}
	
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if settings["variable_%s" % var] is not defined %}
	{ action_raise_error("Variable '%s' is not defined in settings for [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	
	{% for var in vars %}
	{% set var_value = obj[var] %}
	{% if var_value is defined %}
	{% set v = settings["variable_%s" % var] %}
	{% if v != var_value|string %}
	{% if var_value is string %}
	{% set v = '"\'' ~ v|replace('"', '\\"')|replace("'", "\\'") ~ '\'"' %}
	{% endif %}
	SET_GCODE_VARIABLE MACRO={macro} VARIABLE={var} VALUE={v}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Reset {macro} variable {var} to original value: {v} (was {obj[var]})"
	{% endif %}
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro _SHOW_GCODE_VARIABLES]
description = Show current values of specified [gcode_macro ...] variables.
	- MACRO: Name of the GCODE macro containing the variables to show.
	- VARIABLES: Comma-separated list of variable names to show (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- PAD: (optional) If defined, provide a single character to use for padding variable names to align values in a tabular format in the console output. Default is no padding.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set pad = params.PAD|default("") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	
	{% set ns = namespace() %}
	{% set ns.max_len = 0 %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% set ns.max_len = (ns.max_len, var|length)|max %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if pad %}
	{% set padding = pad * (ns.max_len - var|length) %}
	CONSOLE_ECHO MSG="{var}{padding} {obj[var]}"
	{% else %}
	CONSOLE_ECHO MSG="{var}: {obj[var]}"
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro PAUSE]
description = Pauses the print
rename_existing = PAUSE_BASE
variable_extrude = 1.5
variable_retract = 1.5
variable_fan_speed = 0
variable_idex_mode = ""
variable_idex_toolhead = 0
variable_idex_toolhead_x = 0.0
variable_idex_toolhead_y = 0.0
variable_idex_toolhead_z = 0.0
gcode = 
	RATOS_ECHO MSG="Pausing print..."
	
	
	{% set runout_detected = true if params.RUNOUT|default(false)|lower == 'true' else false %}
	
	
	_LED_PAUSE
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	SAVE_GCODE_STATE NAME=PAUSE_state
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_mode VALUE='"{idex_mode}"'
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={idex_toolhead}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_x VALUE={printer.gcode_move.gcode_position.x|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_y VALUE={printer.gcode_move.gcode_position.y|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_z VALUE={printer.gcode_move.gcode_position.z|float}
	DEBUG_ECHO PREFIX="PAUSE" MSG="idex_mode: {idex_mode}, idex_toolhead: {idex_toolhead}, idex_toolhead_x: {idex_toolhead_x}, idex_toolhead_y: {idex_toolhead_y}, idex_toolhead_z: {idex_toolhead_z}"
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="pause"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if current_z < (max_z - 20.0) %}
	{% set z_safe = 20.0 %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	PAUSE_BASE
	
	
	{% if printer["dual_carriage"] is not defined %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan"].speed|float}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	{% if idex_toolhead == 0 %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t1"].speed|float}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106 S0
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set R = printer["gcode_macro PAUSE"].retract|float %}
	{% if can_extrude %}
	G91
	G1 E-{R} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	{% set pause_print_park_x = printer["gcode_macro RatOS"].pause_print_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].pause_print_park_in %}
	{% if runout_detected %}
	{% set pause_print_park_x = printer["gcode_macro RatOS"].runout_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].runout_park_in %}
	{% endif %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	DEBUG_ECHO PREFIX="PAUSE" MSG="z_speed: {z_speed}, pause_print_park_x: {pause_print_park_x}, pause_print_park_in: {pause_print_park_in}, default_toolhead: {default_toolhead}"
	{% if "xyz" in printer.toolhead.homed_axes %}
	G91
	G1 Z{z_safe} F{z_speed}
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% else %}
	
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	_IDEX_SINGLE X={parking_position}
	{% else %}
	PARK_TOOLHEAD
	{% endif %}
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="pause"
	
	RATOS_ECHO MSG="Print paused"

[gcode_macro RESUME]
description = Resumes the print if the printer is paused.
rename_existing = RESUME_BASE
gcode = 
	
	
	RATOS_ECHO MSG="Resuming print..."
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	
	{% set target_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set target_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if target_idex_mode != '' %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set fan_speed = printer["gcode_macro PAUSE"].fan_speed|float %}
	{% if printer["dual_carriage"] is not defined %}
	M106 S{(fan_speed * 255)}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% else %}
	{% if params.TOOLHEAD is defined %}
	
	{% if params.TOOLHEAD == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% else %}
	{% if printer["gcode_macro PAUSE"].idex_toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	{% if params.TOOLHEAD is defined %}
	_SELECT_TOOL T={params.TOOLHEAD} X=-1 Y=-1 TOOLSHIFT=false
	{% else %}
	_SELECT_TOOL T={printer["gcode_macro PAUSE"].idex_toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	{% endif %}
	
	{% set x = printer["gcode_macro PAUSE"].idex_toolhead_x|float %}
	{% set y = printer["gcode_macro PAUSE"].idex_toolhead_y|float %}
	{% set z = printer["gcode_macro PAUSE"].idex_toolhead_z|float %}
	G1 X{x} Y{y} Z{z} F{speed}
	{% if params.TOOLHEAD is defined %}
	
	SAVE_GCODE_STATE NAME=PAUSE_STATE
	{% endif %}
	{% endif %}
	
	
	{% if params.TOOLHEAD is not defined %}
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% if can_extrude %}
	G91
	G1 E{E} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1 MOVE_SPEED={speed}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	RESUME_BASE
	
	
	_LED_PRINTING
	
	RATOS_ECHO MSG="Print resumed"

[gcode_macro CANCEL_PRINT]
description = Cancels the print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	RATOS_ECHO MSG="Cancelling print..."
	END_PRINT
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	
	CANCEL_PRINT_BASE
	RATOS_ECHO MSG="Print cancelled"

[gcode_macro START_PRINT]
description = Start print procedure, use this in your Slicer.
variable_post_processor_version = 2
variable_is_printing_gcode = False
variable_both_toolheads = True
variable_object_xoffset = 0
variable_first_x = -1
variable_first_y = -1
variable_total_toolshifts = 0
variable_initial_tool = 0
variable_extruder_first_layer_temp = ""
variable_extruder_other_layer_temp = ""
gcode = 
	
	{% if params.EXTRUDER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_TEMP parameter not found.")}
	{% endif %}
	{% if params.EXTRUDER_OTHER_LAYER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_OTHER_LAYER_TEMP parameter not found.")}
	{% endif %}
	{% if params.BED_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. BED_TEMP parameter not found.")}
	{% endif %}
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' and printer["gcode_macro RatOS"].danger_force_allow_auto_center_subject|default(false)|lower != 'true'%}
	
	
	
	
	
	{ action_raise_error("The experimental auto_center_subject feature is not supported in this version of RatOS. Please disable it in the RatOS macro settings.") }
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes and printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% if printer["gcode_macro _VAOC"].is_started|default(true)|lower == 'true' %}
	_VAOC_END
	{% endif %}
	{% endif %}
	
	
	_LED_START_PRINTING
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_USER_START_PRINT { rawparams }
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_probe_stowable = printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% endif %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	{% set X0 = params.X0|default(-1)|float %}
	{% set X1 = params.X1|default(-1)|float %}
	{% set Y0 = params.Y0|default(-1)|float %}
	{% set Y1 = params.Y1|default(-1)|float %}
	{% if first_x == -1 or first_y == -1 %}
	{% set first_x = params.FIRST_X|default(-1)|float %}
	{% set first_y = params.FIRST_Y|default(-1)|float %}
	{% endif %}
	{% set total_toolshifts = params.TOTAL_TOOLSHIFTS|default(0)|int %}
	{% set initial_tool = params.INITIAL_TOOL|default(default_toolhead)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	
	
	
	
	
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(printer.heater_bed.target, true)|float %}
	
	
	{% set total_layer_count = params.TOTAL_LAYER_COUNT|default(0)|int %}
	{% set extruder_first_layer_temp = (params.EXTRUDER_TEMP|default("")).split(",") %}
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL BEACON_CONTACT_START_PRINT_TRUE_ZERO={beacon_contact_start_print_true_zero} BEACON_CONTACT_CALIBRATE_MODEL_ON_TRUE_ZERO={beacon_contact_calibrate_model_on_true_zero}
	{% endif %}
	
	_START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH BED_TEMP={bed_temp}
	
	
	RATOS_ECHO MSG="First print coordinates X:{first_x} Y:{first_y}"
	
	
	{% if params.TOTAL_LAYER_COUNT is not defined %}
	{% set link_url = "https://os.ratrig.com/docs/slicers" %}
	{% set link_text = "RatOS Slicer Configuration" %}
	{% set line_1 = '"Your slicer gcode settings are not up to date._N_Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="Incomplete Slicer Configuration detected" TYPE="warning" MSG={line_1}
	{% endif %}
	
	
	SET_PRINT_STATS_INFO CURRENT_LAYER=1
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE=1
	{% if total_layer_count > 0 %}
	SET_PRINT_STATS_INFO TOTAL_LAYER={total_layer_count}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads %}
	{% set initial_tool = 0 if initial_tool == 1 else 1 %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	{% endif %}
	
	
	{% set both_toolheads = true %}
	{% if total_toolshifts == 0 %}
	{% set both_toolheads = false %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	{% endif %}
	{% if both_toolheads and (idex_mode == "copy" or idex_mode == "mirror") %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Gcode tool changes found. Copy and mirror mode do not support toolchanges.")}
	{% endif %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set both_toolheads = true %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=initial_tool VALUE={initial_tool}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_x VALUE={first_x}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_y VALUE={first_y}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=total_toolshifts VALUE={total_toolshifts}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=both_toolheads VALUE={both_toolheads}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_first_layer_temp VALUE="'{params.EXTRUDER_TEMP}'"
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_other_layer_temp VALUE="'{params.EXTRUDER_OTHER_LAYER_TEMP}'"
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE=0
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set svv = printer.save_variables.variables %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set stepper_x_position_min = printer.fastconfig.settings.stepper_x.position_min|float %}
	{% set stepper_x_position_endstop = printer.fastconfig.settings.stepper_x.position_endstop|float %}
	{% set dual_carriage_position_max = printer.fastconfig.settings.dual_carriage.position_max|float %}
	{% set dual_carriage_position_endstop = printer.fastconfig.settings.dual_carriage.position_endstop|float %}
	{% set x_parking_space = parking_position_t0 - (stepper_x_position_endstop , stepper_x_position_min)|max %}
	{% set dc_parking_space = (dual_carriage_position_endstop , dual_carriage_position_max)|min - parking_position_t1 %}
	{% if svv.idex_xoffset|abs >= (x_parking_space - 0.5) or svv.idex_xoffset|abs >= (dc_parking_space - 0.5) %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Toolhead x-offset is too high for the available parking space. Calibrate your X and DC endstop positions and make sure you stay below 1mm." % (copy_mode_max_width)) }
	{% endif %}
	{% endif %}
	
	
	{% if (idex_mode == "copy" or idex_mode == "mirror") and printer.fastconfig.settings.ratos.enable_gcode_transform %}
	
	{% if params.MIN_X is not defined or params.MAX_X is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Something went wrong! Missing important post processor start print parameter!") }
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE=0
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	
	{% set boundary_box_min_x = params.MIN_X|default(0)|float %}
	{% set boundary_box_max_x = params.MAX_X|default(printable_x_max)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if default_toolhead == 0 %}
	
	{% set boundary_box_max_x = boundary_box_max_x + svv.idex_xoffset %}
	{% else %}
	
	{% set boundary_box_min_x = boundary_box_min_x - svv.idex_xoffset %}
	{% endif %}
	
	{% set center_x = printable_x_max / 2.0 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set object_width = boundary_box_max_x - boundary_box_min_x %}
	{% set copy_mode_max_width = center_x %}
	{% set mirror_mode_max_width = center_x - safe_distance / 2.0 %}
	
	DEBUG_ECHO PREFIX="START_PRINT" MSG="OBJECT_WIDTH: {object_width} BOUNDARY_BOX_MIN_X: {boundary_box_min_x} BOUNDARY_BOX_MAX_X: {boundary_box_max_x} CENTER_X: {center_x} SAFE_DISTANCE: {safe_distance}"
	
	
	{% if idex_mode == "copy" and object_width > copy_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for copy mode! Max supported width is %s mm" % (copy_mode_max_width)) }
	{% endif %}
	{% if idex_mode == "mirror" and object_width > mirror_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for mirror mode! Max supported width is %s mm" % (mirror_mode_max_width)) }
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = (printable_x_max - boundary_box_max_x - boundary_box_min_x) / 2 %}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE={object_xoffset}
	{% endif %}
	
	{% endif %}
	
	
	{% set has_initial_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_toolhead_filament_sensor %}
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% set has_initial_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_bowden_filament_sensor %}
	
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% if printer["dual_carriage"] is defined and both_toolheads %}
	
	{% set has_secondary_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set has_secondary_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_CHAMBER_FILTER_ON AT="before_print_start"
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true' %}
	{% if both_toolheads %}
	RATOS_ECHO MSG="Spool join is not possible if both toolheads are in use!"
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	{% endif %}
	
	
	CLEAR_PAUSE
	{% if printer["gcode_macro RatOS"].force_absolute_position|lower == 'true' %}
	G90
	{% endif %}
	SAVE_GCODE_STATE NAME=start_print_state
	
	
	G21
	
	G90
	
	M82
	_USER_START_PRINT_BEFORE_HOMING { rawparams }
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_BEGIN_BATCH
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_Z_HOP
	
	
	{% if idex_mode != '' and not (printer.fastconfig.settings.beacon is defined and (beacon_contact_start_print_true_zero or beacon_adaptive_heat_soak)) %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	{% if chamber_temp > 0 %}
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED={printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float}
	{% endif %}
	{% endif %}
	_CHAMBER_HEATER_ON START_CHAMBER_TEMP={start_chamber_temp} CHAMBER_TEMP={chamber_temp}
	_USER_START_PRINT_HEAT_CHAMBER { rawparams } CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_START_PRINT_BEFORE_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	RATOS_ECHO MSG="Heating bed..."
	
	M190 S{bed_temp}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_adaptive_heat_soak %}
	_MOVE_TO_SAFE_Z_HOME
	
	G1 Z2.5 F{z_speed}
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK LAYER_QUALITY={beacon_adaptive_heat_soak_layer_quality} MAXIMUM_FIRST_LAYER_DURATION={beacon_adaptive_heat_soak_maximum_first_layer_duration} MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={beacon_adaptive_heat_soak_max_wait}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_BED { rawparams }
	
	
	_START_PRINT_AFTER_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	_USER_START_PRINT_BED_MESH { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_BED_MESH X0={X0} X1={X1} Y0={Y0} Y1={Y1} T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_END_BATCH
	{% endif %}
	
	
	{% if idex_mode == '' %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[initial_tool]|float}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[0]|float}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={extruder_first_layer_temp[1]|float}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_PARK { rawparams }
	
	
	_START_PRINT_PARK
	
	
	RATOS_ECHO MSG="Heating Extruder..."
	{% if idex_mode == '' %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[initial_tool]|float}  MAXIMUM={extruder_first_layer_temp[initial_tool]|float + 5}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[0]|float}  MAXIMUM={extruder_first_layer_temp[0]|float + 5}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder1" MINIMUM={extruder_first_layer_temp[1]|float}  MAXIMUM={extruder_first_layer_temp[1]|float + 5}
	{% endif %}
	{% endif %}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	{% if idex_mode == '' %}
	_LED_PRINTING
	{% else %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	_LED_PRINTING
	{% else %}
	{% if both_toolheads %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	{% if toolchange_standby_temp > -1 %}
	_LED_TOOLHEAD_STANDBY TOOLHEAD={0 if initial_tool == 1 else 1}
	{% else %}
	_LED_PRINTING TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% else %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_EXTRUDER { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_AFTER_HEATING_EXTRUDER X0={X0} X1={X1} Y0={Y0} Y1={Y1} INITIAL_TOOLHEAD={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if idex_mode != '' %}
	{% if not both_toolheads %}
	{% if initial_tool != default_toolhead %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if idex_mode != '' %}
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=standby VALUE=False
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=standby VALUE=False
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if initial_tool == 1 else 'extruder1'} TARGET={toolchange_standby_temp}
	SET_GCODE_VARIABLE MACRO=T{0 if initial_tool == 1 else 1} VARIABLE=standby VALUE=True
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=start_print_state
	
	{% if printer["dual_carriage"] is defined %}
	_SET_IDEX_MODE_OFFSET
	{% endif %}
	
	
	{% if idex_mode != '' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% if idex_mode == "copy" and idex_mode != act_idex_mode %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == "mirror" and idex_mode != act_idex_mode %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={object_xoffset} MOVE=0
	{% endif %}
	{% else %}
	_SELECT_TOOL T={initial_tool} TOOLSHIFT=false
	_SET_TOOLHEAD_OFFSET
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	_SET_EXTRUSION_MODE
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={printer["print_stats"].print_duration}
	{% endif %}
	
	
	_USER_END_START_PRINT { rawparams }
	
	G92 E0
	
	
	_CHAMBER_FILTER_ON AT="after_print_start"
	
	_ALERT_NON_ZERO_Z_OFFSET
	
	RATOS_ECHO MSG="Printing..."

[gcode_macro _START_PRINT_BEFORE_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set is_stowable_probe = true if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' else false %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Pre-heating extruder..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={min_temp}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET={min_temp}
	{% endif %}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	{% endif %}
	{% endif %}
	
	
	{% if not is_stowable_probe %}
	{% if printer["dual_carriage"] is defined and act_t != default_toolhead %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	{% endif %}
	RATOS_ECHO MSG="Heat soaking z probe..."
	_MOVE_TO_SAFE_Z_HOME
	
	G0 Z2 F{z_speed}
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Waiting for extruder to be preheated..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	{% if default_toolhead == 0 %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_Z_HOP
	{% endif %}
	
	
	{% if auto_z_offset_calibration %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	PARK_TOOLHEAD
	_CLEANING_MOVE TOOLHEAD={default_toolhead} AUTOMATED=True
	_SELECT_TOOL T={0 if default_toolhead == 1 else 1} X={parking_position_t0 if default_toolhead == 1 else parking_position_t1} Y=0 TOOLSHIFT=false
	_CLEANING_MOVE TOOLHEAD={0 if default_toolhead == 1 else 1} AUTOMATED=True
	_VAOC_CALIBRATE_Z_OFFSET AUTO_Z_OFFSET=True
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=false
	{% endif %}
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	{% if needs_rehoming %}
	G28 Z
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	_START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE
	{% endif %}
	{% endif %}
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	PROBE PROBE_METHOD=contact SAMPLES=1

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	{% set fuzzy_radius = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_radius|default(0)|float if beacon_contact_start_print_true_zero_fuzzy_position else 0 %}
	
	{% set contact_true_zero_temp_has_been_set = False %}
	
	
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	
	
	
	{% if printer.beacon.last_probe_result|lower == "ok" %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	RATOS_ECHO MSG="Auto calibration nozzle wipe with probe result {last_z_offset}..."
	G0 Z{(0.2 + last_z_offset)} F{z_speed}
	G0 X70 F300
	{% else %}
	RATOS_ECHO MSG="Skipping auto calibration nozzle wipe because probing failed!"
	{% endif %}
	{% elif beacon_contact_wipe_before_true_zero_method == "probe_clean" %}
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	
	{% set contact_true_zero_temp_has_been_set = True %}
	
	
	
	
	
	
	
	
	BEACON_PROBE_CLEAN X=50 Y=10
	{% else %}
	CONSOLE_ECHO TYPE="error" TITLE="Unknown wipe method" MSG="Unknown wipe method '{beacon_contact_wipe_before_true_zero_method}' configured, skipping wipe before beacon true zero."
	{% endif %}
	{% endif %}
	
	
	G0 Z5 F{z_speed}
	_MOVE_TO_SAFE_Z_HOME FUZZY_RADIUS={fuzzy_radius}
	
	
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION
	
	{% if not contact_true_zero_temp_has_been_set %}
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon contact auto calibration..."
	
	{% if beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	
	G0 Z5 F{z_speed}

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION]
gcode = 
	{% set pos = printer.ratos.last_move_to_safe_z_home_position %}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE={pos[0]}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE={pos[1]}

[gcode_macro _START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set first_x = printer["gcode_macro START_PRINT"].first_x|default(-1)|float %}
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2.0 %}
	{% set center_y = printable_y_max / 2.0 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% if printer["dual_carriage"] is defined %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% endif %}
	
	
	{% set X0 = params.X0|default(-1)|int %}
	{% set X1 = params.X1|default(-1)|int %}
	{% set Y0 = params.Y0|default(-1)|int %}
	{% set Y1 = params.Y1|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	
	{% if idex_mode == '' %}
	
	_PRIME
	{% else %}
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	RATOS_ECHO PREFIX="IDEX" MSG="using combined prime offset for IDEX {idex_mode} mode"
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	{% if both_toolheads %}
	{% if initial_toolhead == 0 %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T{initial_toolhead}"
	_SELECT_TOOL T={initial_toolhead} TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	SET_MACRO_TRAVEL_SETTINGS
	
	{% if (X0 > -1 and Y1 > -1) or (first_x > 0 and first_y > 0) %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	{% endif %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	{% set first_z = 1 %}
	{% else %}
	{% set first_z = 3 %}
	{% endif %}
	
	
	{% if idex_mode == "mirror" %}
	{% if first_y >= 0 %}
	G0 Y{first_y} F{speed}
	{% else %}
	G0 Y{Y1} F{speed}
	{% endif %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={initial_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={initial_toolhead} E={printer["gcode_macro RatOS"].toolchange_first_purge|default(50)|float}
	_CLEANING_MOVE TOOLHEAD={initial_toolhead} AUTOMATED=True
	{% endif %}
	{% if first_x >= 0 and first_y >= 0 %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% else %}
	{% set first_x = X0 %}
	{% set first_y = Y0 %}
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'min' %}
	{% set first_x = X0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'max' %}
	{% set first_x = X1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|float <= center_x %}
	{% set first_x = X0 %}
	{% else %}
	{% set first_x = X1 %}
	{% endif %}
	{% endif %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'min' %}
	{% set first_y = Y0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'max' %}
	{% set first_y = Y1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|float <= center_y %}
	{% set first_y = Y0 %}
	{% else %}
	{% set first_y = Y1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	
	
	_LOAD_RATOS_SKEW_PROFILE

[gcode_macro _PRIME]
gcode = 
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	PRIME_BLOB INITIAL_TOOLHEAD={params.INITIAL_TOOLHEAD} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={params.IDEX_MODE} Y1={params.Y1}
	{% else %}
	
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif params.IDEX_MODE == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro END_PRINT]
description = End print procedure, use this in your Slicer.
gcode = 
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SAVE_GCODE_STATE NAME=end_print_state
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = printer["gcode_macro START_PRINT"].object_xoffset|default(0)|float %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(0-object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={(0-object_xoffset)}
	{% endif %}
	{% endif %}
	
	
	_USER_END_PRINT_BEFORE_HEATERS_OFF { rawparams }
	_END_PRINT_BEFORE_HEATERS_OFF
	TURN_OFF_HEATERS
	_USER_END_PRINT_AFTER_HEATERS_OFF { rawparams }
	_END_PRINT_AFTER_HEATERS_OFF
	_USER_END_PRINT_PARK { rawparams }
	_END_PRINT_PARK
	
	
	{% if printer["gcode_macro RatOS"].skew_profile is defined %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined and printer["gcode_macro RatOS"].end_print_motors_off|lower != 'false' %}
	
	M84
	{% endif %}
	
	
	M107
	
	
	BED_MESH_CLEAR
	RATOS_ECHO MSG="Done :)"
	
	
	RESTORE_GCODE_STATE NAME=end_print_state
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	M84
	{% endif %}
	
	
	RESET_NAMED_OFFSET EVENT="end_print"
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_CHAMBER_FILTER_ON AT="print_end"
	_CHAMBER_FILTER_OFF
	
	
	_CHAMBER_HEATER_OFF
	
	_USER_END_PRINT_FINISHED { rawparams }

[gcode_macro _END_PRINT_BEFORE_HEATERS_OFF]
gcode = 
	RATOS_ECHO MSG="Cleaning up..."

[gcode_macro _END_PRINT_AFTER_HEATERS_OFF]
gcode = 
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% set z_hop = printer["gcode_macro RatOS"].end_print_park_z_hop|float %}
	{% set r = printer["gcode_macro RatOS"].end_print_retract_filament|default(4)|float %}
	{% if current_z < (max_z - z_hop) %}
	{% set z_safe = z_hop %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G91
	
	{% if can_extrude %}
	G1 E-2 F3600
	{% endif %}
	
	G0 Z{z_safe} F3600
	
	{% if can_extrude %}
	G1 E-{(r-2)} F3600
	{% endif %}
	
	G90

[gcode_macro _SET_EXTRUSION_MODE]
gcode = 
	
	{% if printer["gcode_macro RatOS"].relative_extrusion|lower == 'true' %}
	M83
	{% else %}
	M82
	{% endif %}

[gcode_macro GENERATE_SHAPER_GRAPHS]
description = Genarates input shaper resonances graphs for analysis. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	{% set hz_per_sec = params.HZ_PER_SEC|default(1)|float %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set copy_mode_offset = printable_x_max / 4.0 %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	_IDEX_SINGLE
	{% endif %}
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	
	
	{% if idex_mode != 'copy' and idex_mode != 'mirror' %}
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	{% endif %}
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Shaper graph"

[gcode_shell_command generate_shaper_graph_x]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-x.sh
timeout = 60.
verbose = True

[gcode_shell_command generate_shaper_graph_y]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-y.sh
timeout = 60.
verbose = True

[gcode_macro MEASURE_COREXY_BELT_TENSION]
description = Generates resonance graph used to ensure belts are equally tensioned. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	_IDEX_SINGLE
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if measure_t1 == false or measure_t0 == false %}
	{action_raise_error("Axis specified. Not supported for belt tension on Y.")}
	{% else %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	G4 P5000
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	PARK_TOOLHEAD
	{% endif %}
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	G1 X{parking_position_t1} F{speed}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	
	
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Belt Tension Graph"

[gcode_shell_command generate_belt_tension_graph]
command = /home/pi/printer_data/config/RatOS/scripts/generate-belt-tension-graph.sh
timeout = 90.
verbose = True

[idle_timeout]
gcode = 
	{% if printer.webhooks.state|lower == 'ready' %}
	{% if printer.pause_resume.is_paused|lower == 'false' %}
	_USER_BEFORE_IDLE_TIMEOUT
	RATOS_ECHO PREFIX="IDLE" MSG="2 hours since last activity. Powering off heaters and motors.."
	TURN_OFF_HEATERS
	M84
	_USER_AFTER_IDLE_TIMEOUT
	{% endif %}
	{% endif %}
timeout = 7200

[temperature_sensor raspberry_pi]
sensor_type = temperature_host

[skew_correction]

[named_offsets]

[input_shaper]

[virtual_sdcard]
path = ~/printer_data/gcodes

[display_status]

[pause_resume]

[force_move]
enable_force_move = True

[respond]

[resonance_generator]

[ratos]
allow_unknown_gcode_generator = True
enable_gcode_transform = True

[exclude_object]

[bed_mesh]
split_delta_z = 0.001
horizontal_move_z = 2
mesh_min = 20,20
mesh_max = 480,480
probe_count = 40,40
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = .2
speed = 600
log_points = False

[fastconfig]

[heater_bed]
heater_pin = heater_bed_heating_pin
sensor_pin = heater_bed_sensor_pin
sensor_type = Generic 3950
min_temp = 0
max_temp = 140
pwm_cycle_time = 0.103
control = pid
pid_kp = 61.987
pid_ki = 1.781
pid_kd = 539.289

[printer]
kinematics = ratos_hybrid_corexy
max_velocity = 800
max_accel = 10000
minimum_cruise_ratio = 0.5
max_z_velocity = 50
max_z_accel = 600
square_corner_velocity = 5

[ratos_hybrid_corexy]
inverted = true

[dual_carriage]
axis = x
safe_distance = 55
position_max = 559.6
position_endstop = 559.6
position_min = 0
step_pin = PF9
dir_pin = dual_carriage_dir_pin
enable_pin = !PG2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t1:PA2

[gcode_macro _SET_IDEX_MODE_OFFSET]
description = "Internal use only. Sets the 'idex_mode' named offset that the active idex mode requires."
gcode = 
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_SET_IDEX_MODE_OFFSET" MSG="idex_mode: {idex_mode}, center_x: {center_x}"
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	SET_NAMED_OFFSET NAME=idex_mode X={(-center_x / 2)}
	{% else %}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% else %}
	{action_raise_error("_SET_IDEX_MODE_OFFSET: Printer not homed")}
	{% endif %}

[gcode_macro IDEX_SINGLE]
gcode = 
	_IDEX_REMAP_TOOLHEADS ENABLE=False
	_IDEX_SINGLE

[gcode_macro _IDEX_SINGLE]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_single"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set init = params.INIT|default(0)|int %}
	{% set new_x = params.X|default(-1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_default_t = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="init: {init}, new_x: {new_x}, idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, act_t: {act_t}"
	
	{% if idex_mode == "copy" or idex_mode == "mirror" or init == 1 %}
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="reset idex_mode offset"
	G1 X{center_x} F{(speed)}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="activate default carriage"
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolheads"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	G90
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position."
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1}
	G1 X{parking_position_default_t} F{speed}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move default toolhead to its new position."
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% if new_x == -1 %}
	{% set new_x = center_x %}
	{% endif %}
	G1 X{new_x} F{speed}
	
	M400
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="X Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set extruder motion queue."
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if default_toolhead==0 else default_toolhead}
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolhead offset."
	_SET_TOOLHEAD_OFFSET
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set input shaper."
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[default_toolhead]|float)} SHAPER_FREQ_Y={(shaper_y_freq[default_toolhead]|float)} SHAPER_TYPE_X={(shaper_x_type[default_toolhead]|lower)} SHAPER_TYPE_Y={(shaper_y_type[default_toolhead]|lower)}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="update Frontend."
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if default_toolhead==0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if default_toolhead==1 else False}
	{% else %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_single"

[gcode_macro IDEX_COPY]
gcode = 
	_IDEX_COPY

[gcode_macro _IDEX_COPY]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_copy"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set y = params.Y|default(-1)|int %}
	{% set dance = params.DANCE|default(1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_COPY" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}, y: {y}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "copy" %}
	{% if idex_mode == "mirror" %}
	{% if y>=0 %}
	G1 X{center_x} Y{y} F{(speed)}
	{% else %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	
	
	{% if idex_mode != "mirror" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance == 1 %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[2]|float)} SHAPER_FREQ_Y={(shaper_y_freq[2]|float)} SHAPER_TYPE_X={(shaper_x_type[2]|lower)} SHAPER_TYPE_Y={(shaper_y_type[2]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_copy"

[gcode_macro IDEX_MIRROR]
gcode = 
	_IDEX_MIRROR

[gcode_macro _IDEX_MIRROR]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_mirror"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set dance = params.DANCE|default(1)|int %}
	{% set priming = params.PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_MIRROR" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "mirror" %}
	
	{% if idex_mode == "copy" %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS MIRROR_PRIMING={params.PRIMING}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=MIRROR
	
	
	{% if idex_mode != "copy" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance and not priming %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[3]|float)} SHAPER_FREQ_Y={(shaper_y_freq[3]|float)} SHAPER_TYPE_X={(shaper_x_type[3]|lower)} SHAPER_TYPE_Y={(shaper_y_type[3]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_mirror"

[gcode_macro _IDEX_SET_TOOLHEADS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set mirror_priming = params.MIRROR_PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position_inactive_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_IDEX_SET_TOOLHEADS" MSG="idex_mode: {idex_mode}, act_t: {act_t}, center_x: {center_x}, mirror_priming: {mirror_priming}"
	
	
	{% if act_t != default_toolhead %}
	_SET_TOOLHEAD_OFFSET FORCE_TOOLHEAD={default_toolhead} MOVE=1
	{% endif %}
	
	{% if mirror_priming %}
	
	
	
	{% if parking_position_t0|abs < parking_position_t1 - printable_x_max %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{printable_x_max + parking_position_t0|abs} F{(speed)}
	{% else %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{0 - (parking_position_t1 - printable_x_max)} F{(speed)}
	{% endif %}
	
	{% else %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1} MODE=PRIMARY
	G1 X{parking_position_inactive_t} F{(speed)}
	
	
	{% if act_t==1 %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{center_x / 2} F{(speed)}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"

[gcode_macro IDEX_PARK]
gcode = 
	
	PARK_TOOLHEAD

[gcode_macro PARK_TOOLHEAD]
gcode = 
	
	{% set idex_mode = 'none' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="PARK_TOOLHEAD" MSG="Parking T{act_t}.."
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set parking_position_inact_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set printable_y_min = printer["gcode_macro RatOS"].printable_y_min|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" and 'xy' in printer.toolhead.homed_axes %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% elif printer.toolhead.position.y|float < printable_y_min %}
	G1 Y{printable_y_min} F{speed}
	{% endif %}
	
	SAVE_GCODE_STATE NAME=_PARK_TOOLHEAD
	G90
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0.5
	
	
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_inact_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	
	SET_VELOCITY_LIMIT ACCEL={printer.toolhead.max_accel} MINIMUM_CRUISE_RATIO=0.5
	M400
	RESTORE_GCODE_STATE NAME=_PARK_TOOLHEAD
	
	{% endif %}

[gcode_macro JOIN_SPOOLS]
gcode = 
	
	{% set spools = params.SPOOLS|default("") %}
	
	{% if spools == "" %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% else %}
	{% if spools != "0,1" and spools != "1,0" %}
	RATOS_ECHO MSG="Wrong spool configuration!"
	RATOS_ECHO MSG="Join Spools = JOIN_SPOOLS SPOOLS=0,1"
	RATOS_ECHO MSG="Deactivate = JOIN_SPOOLS SPOOLS="
	{% else %}
	{% if spools == "0,1" or spools == "1,0" %}
	_IDEX_JOIN_SPOOLS ENABLE=true
	{% else %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_JOIN_SPOOLS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if enable %}
	{% set has_t0_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t1_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t0_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined else false %}
	{% set has_t1_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined else false %}
	{% if (has_t0_toolhead_filament_sensor and has_t1_toolhead_filament_sensor) or (has_t0_bowden_filament_sensor and has_t1_bowden_filament_sensor) %}
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=True
	RATOS_ECHO MSG="Spool joining enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Can not enable spool joining! No filament sensors found."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining deactivated!"
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining is not possible in copy and mirror mode!"
	{% endif %}

[gcode_macro _JOIN_SPOOL]
gcode = 
	
	{% set old_toolhead = params.TOOLHEAD|int %}
	{% set new_toolhead = 0 if old_toolhead == 1 else 1 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set purge_after_load = printer["gcode_macro T%s" % new_toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_JOIN_SPOOL" MSG="toolhead: {new_toolhead}"
	
	{% set has_filament = true %}
	{% set has_new_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% set has_new_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% if has_new_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	{% if has_new_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	
	{% if has_filament %}
	RATOS_ECHO MSG="Joining spools! Please wait for extruder to heat up...."
	
	
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={new_toolhead}
	
	
	_DEACTIVATE_TOOLHEAD TOOLHEAD={old_toolhead}
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set extruder_temp = extruder_first_layer_temp[new_toolhead]|float %}
	{% else %}
	{% set extruder_temp = extruder_other_layer_temp[new_toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if new_toolhead == 0 else 'extruder1'} TARGET={extruder_temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if new_toolhead == 0 else 'extruder1'} MINIMUM={extruder_temp}  MAXIMUM={extruder_temp + 5}
	
	
	{% if purge_after_load > 0 %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_toolhead == 0 else new_toolhead}
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={new_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={new_toolhead} E={purge_after_load}
	_CLEANING_MOVE TOOLHEAD={new_toolhead} AUTOMATED=True
	
	
	SET_DUAL_CARRIAGE CARRIAGE={old_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if old_toolhead == 0 else old_toolhead}
	
	{% endif %}
	
	
	RESUME TOOLHEAD={new_toolhead}
	
	
	_IDEX_JOIN_SPOOLS ENABLE=false
	
	{% else %}
	{ action_raise_error("Spool join failed! No filament found or filament sensor is disabled.") }
	{% endif %}

[gcode_macro REMAP_TOOLHEADS]
gcode = 
	
	{% set toolheads = params.TOOLHEADS|default("") %}
	
	{% if toolheads == "" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% else %}
	{% if toolheads != "0,1" and toolheads != "1,0" %}
	RATOS_ECHO MSG="Wrong toolhead configuration!"
	RATOS_ECHO MSG="Remap = REMAP_TOOLHEADS TOOLHEADS=0,1"
	RATOS_ECHO MSG="Deactivate = REMAP_TOOLHEADS TOOLHEADS="
	{% else %}
	{% if toolheads == "0,1" or toolheads == "1,0" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=true
	_IDEX_SINGLE
	{% else %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_REMAP_TOOLHEADS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	{% if not enable or (idex_mode != "copy" and idex_mode != "mirror") %}
	{% if enable %}
	RATOS_ECHO MSG="Toolhead remapping enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping deactivated!"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE={enable}
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping not possible in copy and mirror mode!"
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	{% endif %}

[gcode_macro SHAPER_CALIBRATE]
rename_existing = SHAPER_CALIBRATE_ORG
gcode = 
	RATOS_ECHO PREFIX="IDEX" MSG="SHAPER_CALIBRATE is useless on IDEX machines. Please use the GENERATE_SHAPER_GRAPHS macro and type the values into `variable_shaper_*_freq` and `variable_shaper_*_type manually`."

[gcode_shell_command generate_shaper_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-shaper-graph.sh
timeout = 120.
verbose = True

[gcode_shell_command generate_tension_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-belt-tension-graph.sh
timeout = 120.
verbose = True

[gcode_macro SET_PRESSURE_ADVANCE]
variable_snyc_toolheads = False
rename_existing = SET_PRESSURE_ADVANCE_BASE
gcode = 
	{% if params.SYNC_TOOLHEADS is defined %}
	{% set snyc_toolheads = true if params.SYNC_TOOLHEADS|default(false)|lower == 'true' else false %}
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=True
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="Syncing toolheads..."
	{% else %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' or snyc_toolheads %}
	{% set advance = params.ADVANCE|default(printer['extruder'].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['extruder'].smooth_time|float)|float %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T0"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T1"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder1' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% else %}
	{% set extruder = 'extruder' if act_t == 0 else 'extruder1' %}
	{% if params.EXTRUDER is defined %}
	{% set extruder = params.EXTRUDER %}
	{% endif %}
	{% if extruder == 'extruder' or extruder == 'extruder1' %}
	{% set advance = params.ADVANCE|default(printer['%s' % extruder].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['%s' % extruder].smooth_time|float)|float %}
	SET_PRESSURE_ADVANCE_BASE EXTRUDER={extruder} ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% if params.EXTRUDER is not defined %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG={"T%s" % act_t}
	{% endif %}
	{% else %}
	SET_PRESSURE_ADVANCE_BASE { rawparams }
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro M106]
rename_existing = M106.1
variable_swap_speed = -1
gcode = 
	
	{% set s = [[params.S|default(255)|int, 255]|min, 0]|max %}
	{% set p = params.P|default(-1)|int %}
	{% set speed = s / 255 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set t = 1 if idex_mode=='primary' else 0 %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(0)|int == 1 else false %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set sync_fans = true %}
	{% endif %}
	
	
	{% if sync_fans and idex_mode != "copy" and idex_mode != "mirror" %}
	
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int %}
	
	
	{% if toolshift_count > total_toolshifts %}
	{% set sync_fans = false %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE=-1
	
	
	{% if p == -1 %}
	
	{% if speed == 0 %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed}
	{% else %}
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE={speed}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={(speed if (t == 0 or sync_fans) else 0)}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={(speed if (t == 1 or sync_fans) else 0)}
	{% endif %}
	{% else %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed if t == p else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed if t == p else 0}
	{% endif %}
	
	
	M106.1 S{s}

[gcode_macro M107]
rename_existing = M107.1
gcode = 
	{% set p = params.P|default(-1)|int %}
	M106 S0 P{p}

[gcode_macro _SELECT_TOOL]
variable_last_timestamp = 0
gcode = 
	{% if params.T is defined %}
	{% set idex_mode = '' %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if "xyz" not in printer.toolhead.homed_axes and (idex_mode == "copy" or idex_mode == "mirror") %}
	_IDEX_SINGLE
	{% set idex_mode = 'reset' %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set new_t = params.T|int %}
	
	
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads and is_printing_gcode %}
	{% set new_t = 0 if new_t == 1 else 1 %}
	{% endif %}
	
	
	{% set toolchange_prepurging_timer = printer["gcode_macro RatOS"].toolchange_prepurging_timer|default(0)|int %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	DEBUG_ECHO PREFIX="_SELECT_TOOL" MSG="act_t: {act_t}, new_t: {new_t}, is_printing_gcode: {is_printing_gcode}, swap_toolheads: {swap_toolheads}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	{% set act_extruder = 'extruder%s' % ('' if new_t == 0 else new_t) %}
	{% if new_t != act_t or printer.toolhead.extruder != act_extruder or idex_mode == 'reset' %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Selecting T{new_t}.."
	
	
	M220 S100
	
	
	
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(1)|int == 1 else false %}
	
	
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set toolshift = false %}
	{% endif %}
	
	
	{% set fan_speed = printer["fan_generic part_fan_t%s" % act_t].speed %}
	
	
	{% set deactivate_toolhead = false %}
	{% if is_printing_gcode %}
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int + 1 %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE={toolshift_count}
	{% if toolshift_count == total_toolshifts %}
	{% set deactivate_toolhead = true %}
	{% endif %}
	{% endif %}
	
	
	{% set needs_wakeup = true if printer["gcode_macro T%s" % new_t].standby|default(false)|lower == 'true' else false %}
	
	
	{% set needs_purging = false %}
	{% set wake_up_purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% if is_printing_gcode and toolchange_prepurging_timer > 0 and wake_up_purge > 0 %}
	{% set new_timestamp = printer["print_stats"].print_duration %}
	{% set elapsed_time = new_timestamp - last_timestamp %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={new_timestamp}
	{% if elapsed_time > toolchange_prepurging_timer %}
	{% set needs_purging = true %}
	{% endif %}
	{% endif %}
	
	
	{% set first_use_purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% if toolshift_count == 1 and first_use_purge > 0 %}
	{% set needs_purging = true %}
	{% endif %}
	
	
	{% if is_printing_gcode and (toolchange_standby_temp > -1 or needs_purging or needs_wakeup) %}
	_TOOLHEAD_STANDBY TOOLHEAD={act_t}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	_TOOLHEAD_WAKEUP TOOLHEAD={new_t} X={new_x} Y={new_y} Z={new_z} FAN_SPEED={fan_speed} TOOLSHIFT_COUNT={toolshift_count}
	{% else %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(false)|lower == 'true' else false %}
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if (new_t == 0 or sync_fans) else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if (new_t == 1 or sync_fans) else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	_TOOLCHANGE T={new_t} X={new_x} Y={new_y} Z={new_z} PARK_T0={park_t0} PARK_T1={park_t1} TOOLSHIFT={toolshift}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[new_t]|float)} SHAPER_FREQ_Y={(shaper_y_freq[new_t]|float)} SHAPER_TYPE_X={(shaper_x_type[new_t]|lower)} SHAPER_TYPE_Y={(shaper_y_type[new_t]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if new_t == 0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if new_t == 1 else False}
	
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% set sanity_check_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if new_t == 0 %}
	{% if printer.toolhead.extruder == 'extruder' %}
	{% if sanity_check_idex_mode == 'primary' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% elif new_t == 1 %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% if sanity_check_idex_mode == 'inactive' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _TOOLHEAD_STANDBY]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Putting toolhead T{toolhead} into standby mode."
	DEBUG_ECHO PREFIX="_TOOLHEAD_STANDBY" MSG="toolhead: {toolhead}, config_z_hop: {config_z_hop}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={toolhead} SYNC=0
	PARK_TOOLHEAD
	
	
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={toolchange_standby_temp}
	{% endif %}
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=True
	{% endif %}
	
	
	_LED_TOOLHEAD_STANDBY TOOLHEAD={toolhead}

[gcode_macro _TOOLHEAD_WAKEUP]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set fan_speed = params.FAN_SPEED|float %}
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift_count = params.TOOLSHIFT_COUNT|default(0)|int %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% if toolshift_count == 1 %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% endif %}
	{% set needs_wakeup = true if printer["gcode_macro T%s" % toolhead].standby|default(false)|lower == 'true' else false %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Waking up toolhead T{toolhead}. Please wait for extruder to heat up..."
	DEBUG_ECHO PREFIX="_TOOLHEAD_WAKEUP" MSG="toolhead: {toolhead}, fan_speed: {fan_speed}, new_x: {new_x}, new_y: {new_y}, new_z: {new_z}, config_z_hop: {config_z_hop}"
	
	
	_LED_TOOLHEAD_WAKEUP TOOLHEAD={toolhead}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={toolhead} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE=1
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if toolhead == 0 else toolhead}
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if needs_wakeup %}
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set temp = extruder_first_layer_temp[toolhead]|float %}
	{% else %}
	{% set temp = extruder_other_layer_temp[toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if toolhead == 0 else 'extruder1'} MINIMUM={temp}  MAXIMUM={temp + 5}
	{% endif %}
	
	
	_LED_PRINTING TOOLHEAD={toolhead}
	
	
	{% if purge > 0 %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={toolhead} E={purge}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	
	
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if toolhead == 1 else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	G92 E0
	G1 E-{e} F{feedrate}
	G92 E0
	
	
	{% if new_x >= 0 and new_y >= 0 %}
	G1 X{new_x} Y{new_y} F{speed}
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={config_z_hop} T={toolhead} SYNC=0
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=False

[gcode_macro _TOOLCHANGE]
variable_toolshift_count = 0
gcode = 
	
	
	{% set new_t = params.T|default(-1)|int %}
	{% set new_x = params.X|default(-1.0)|float %}
	{% set new_y = params.Y|default(-1.0)|float %}
	{% set new_z = params.Z|default(-1.0)|float %}
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(true)|lower == 'true' else false %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T: {new_t}, X: {new_x}, Y: {new_y}, Z: {new_z}, PARK_T0: {park_t0}, PARK_T1: {park_t1}, IS_PRINTING_GCODE: {is_printing_gcode}, TOOLSHIFT: {toolshift}"
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	{% if park_t0 >= 0 and park_t1 >= 0 %}
	{% set parking_position_t0 = park_t0 %}
	{% set parking_position_t1 = park_t1 %}
	{% set parking_position_act_t = park_t0 if act_t == 0 else park_t1 %}
	{% endif %}
	
	
	{% if not is_printing_gcode and not toolshift %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Changing tool to T{new_t} without retracting/extruding or moving the toolheads except for parking."
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	G90
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% if not is_printing_gcode and toolshift and new_x < 0 and new_y < 0 %}
	{% set new_x = center_x %}
	{% set new_y = printer.gcode_move.gcode_position.y|float %}
	{% endif %}
	
	{% if new_x < 0 or new_y < 0 %}
	
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="No new X or Y position given, parking the active toolhead and activating the new toolhead without moving it."
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={new_t}
	
	
	{% if "x" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	{% if is_printing_gcode %}
	_EXTRUDE T={new_t}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	{% if "xyz" not in printer.toolhead.homed_axes %}
	
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	
	
	{% set svv = printer.save_variables.variables %}
	{% if new_t == default_toolhead %}
	{% set new_xoffset = 0 %}
	{% set new_yoffset = 0 %}
	{% set new_zoffset = 0 %}
	{% else %}
	{% set new_xoffset = -svv.idex_xoffset %}
	{% set new_yoffset = -svv.idex_yoffset %}
	{% set new_zoffset = -svv.idex_zoffset %}
	{% endif %}
	
	{% set xoffset_correction = new_xoffset - printer.named_offsets.toolhead_alignment.x %}
	{% set yoffset_correction = new_yoffset - printer.named_offsets.toolhead_alignment.y %}
	{% set zoffset_correction = new_zoffset - printer.named_offsets.toolhead_alignment.z %}
	
	{% if new_t == 0 %}
	
	{% set t0_act_x = parking_position_t0 %}
	{% set t1_act_x = printer.toolhead.position.x|float %}
	{% set t0_new_x = new_x %}
	{% set t1_new_x = parking_position_t1 %}
	{% set t0_distance = t0_new_x - t0_act_x %}
	{% set t1_distance = t1_new_x - t1_act_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T0."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	
	
	G1 X{t0_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x + (t1_new_x - t1_act_x)} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t0_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T0: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% elif new_t == 1 %}
	
	{% set t0_act_x = printer.toolhead.position.x|float %}
	{% set t1_act_x = parking_position_t1 %}
	{% set t0_new_x = parking_position_t0 %}
	{% set t1_new_x = new_x %}
	{% set t0_distance = t0_act_x - t0_new_x %}
	{% set t1_distance = t1_act_x - t1_new_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T1."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x - t1_distance + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t1_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T1: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% endif %}
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	{% endif %}

[gcode_macro _ZHOP_BEFORE_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_hop = params.Z_HOP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_HOP: {z_hop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="COMBINED_ZHOP G1 Z+{z_hop} E-{e} F{speed * 60}"
	G1 Z+{z_hop} E-{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="ZHOP G1 Z+{z_hop} F{speed * 60}"
	G1 Z+{z_hop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="RETRACT G1 E-{e} F{feedrate}"
	G1 E-{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _ZDROP_AFTER_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_drop = params.Z_DROP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_DROP: {z_drop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="COMBINED_ZDROP G1 Z-{z_drop} E{e} F{speed * 60}"
	G1 Z-{z_drop} E{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="ZDROP G1 Z-{z_drop} F{speed * 60}"
	G1 Z-{z_drop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="EXTRUDE G1 E{e} F{feedrate}"
	G1 E{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _EXTRUDE]
gcode = 
	
	{% set t = params.T|int %}
	
	
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	
	DEBUG_ECHO PREFIX="_EXTRUDE" MSG="G1 E{e} F{feedrate * 60}"
	
	
	G91
	M82
	G92 E0
	G1 E{e} F{feedrate * 60}
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _DEACTIVATE_TOOLHEAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_DEACTIVATE_TOOLHEAD" MSG="TOOLHEAD {toolhead}"
	
	
	{% if toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% endif %}
	
	
	M106.1 S0
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={toolhead}

[delayed_gcode _INIT_TOOLHEADS]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	_IDEX_SINGLE INIT=1
	
	
	{% if printer.fastconfig.settings.dual_carriage.safe_distance is defined %}
	{% if printer.fastconfig.settings.dual_carriage.safe_distance|float < 50 %}
	{ action_emergency_stop("Dual carriage safe_distance seems to be too low!") }
	{% endif %}
	{% else %}
	{ action_emergency_stop("Dual carriage safe_distance not defined!") }
	{% endif %}

[gcode_macro _SET_TOOLHEAD_OFFSET]
description = "Internal use only. Sets the toolhead_alignment offset (and hotend_thermal_expansion offset when configured) for the active/dominant toolhead."
gcode = 
	
	{% set move = params.MOVE|default(0)|int %}
	{% set force_toolhead = params.FORCE_TOOLHEAD|default(-1)|int %}
	
	
	{% if params.T is defined %}
	CONSOLE_ECHO TYPE="error" MSG="_SET_TOOLHEAD_OFFSET called with deprectated T parameter, which is ignored."
	{';$_SET_TOOLHEAD_OFFSET_ignoring_TOOLHEAD_parameter'}
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="active/dominant toolhead: {toolhead}, MOVE: {move}, FORCE_TOOLHEAD: {force_toolhead}"
	
	
	{% if force_toolhead >= 0 %}
	{% set toolhead = force_toolhead %}
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="FORCE_TOOLHEAD applied, using TOOLHEAD: {toolhead}"
	{% endif %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set move = 0 %}
	{% endif %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|int %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X=0 Y=0 MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z=0 MOVE={move} SPEED={z_speed}
	{% else %}
	{% set svv = printer.save_variables.variables %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X={(-svv.idex_xoffset)} Y={(-svv.idex_yoffset)} MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-svv.idex_zoffset)} MOVE={move} SPEED={z_speed}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}

[gcode_macro TOOLSHIFT_CONFIG]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={params.SPEED|default(300)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={params.ACCEL|default(5000)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_retraction VALUE={params.RETRACT|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_extrusion VALUE={params.EXTRUDE|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_feedrate VALUE={params.FEEDRATE|default(7200)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={params.Z_HOP|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zspeed VALUE={params.Z_SPEED|default(25)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_combined_zhop VALUE={true if params.COMBINED_ZHOP|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_sync_fans VALUE={true if params.SYNC_FANS|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_prepurging_timer VALUE={params.AUTO_PURGE_TIME|default(0)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_purge VALUE={params.PURGE|default(25)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_standby_temp VALUE={params.STANDBY_TEMP|default(-1)|float}

[gcode_macro CALCULATE_DC_ENDSTOP]
description = "DEPRECATED: This macro has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."
gcode = 
	CONSOLE_ECHO TITLE="CALCULATE_DC_ENDSTOP has been deprecated" TYPE="error" MSG="The CALCULATE_DC_ENDSTOP has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."

[gcode_macro _VAOC]
variable_is_fixed = True
variable_is_started = False
variable_is_started_at_temp = False
variable_additional_safe_distance = 50
variable_safe_z = 30
variable_auto_z_offset_calibration = True
variable_enable_camera_cooling = True
variable_camera_cooling_fan_speed = 0.3
variable_camera_cooling_temperature = 50
variable_toolchange_travel_speed = 300
variable_toolchange_travel_accel = 5000
variable_adjusting_secondary_toolhead_focus_adjusts_zoffset = False
variable_cache_toolchange_travel_speed = 300
variable_cache_toolchange_travel_accel = 5000
variable_cache_toolchange_zhop = 1.0
variable_t0_toolhead_sensor_enabled = 0
variable_t1_toolhead_sensor_enabled = 0
variable_t0_bowden_sensor_enabled = 0
variable_t1_bowden_sensor_enabled = 0
variable_loaded_skew_profile = ""
variable_gcode_z_offset = 0.0
variable_start_x_offset = 0.0
variable_start_y_offset = 0.0
gcode = 
	_ECHO_VAOC_VARS
variable_expected_camera_x_position = 212.5
variable_expected_camera_y_position = 530.5

[gcode_macro _VAOC_START]
description = Called from the front end. If T0_TEMP, T1_TEMP and BED_TEMP parameter are specified, VAOC calibration will start under real conditions at printing temp.
gcode = 
	
	{% set t0_temp = params.T0_TEMP|default(0)|int %}
	{% set t1_temp = params.T1_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(0)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro SKEW_PROFILE"].loaded_profile|default("") %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=loaded_skew_profile VALUE='"{loaded_skew_profile}"'
	
	
	{% if t0_temp > 0 and t1_temp > 0 and bed_temp > 0 %}
	
	
	{% if not is_fixed %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("VAOC calibration at temp works only with a fixed installed VAOC device.") }
	{% endif %}
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE=0
	{% endif %}
	
	
	START_PRINT EXTRUDER_TEMP={t0_temp},{t1_temp} EXTRUDER_OTHER_LAYER_TEMP={t0_temp},{t1_temp} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp} INITIAL_TOOL=0 TOTAL_LAYER_COUNT=1 X0={(printable_x_max / 2 - 10)} Y0={(printable_y_max / 2 - 10)} X1={(printable_x_max / 2 + 10)} Y1={(printable_y_max / 2 + 10)} TOTAL_TOOLSHIFTS=1 FIRST_X={printable_x_max / 2} FIRST_Y={printable_y_max / 2} MIN_X={(printable_x_max / 2 - 10)} MAX_X={(printable_x_max / 2 + 10)} USED_TOOLS=0,1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=True
	
	{% endif %}
	
	
	_START_VAOC

[gcode_macro _START_VAOC]
description = Called from _VAOC_START. Do not call it manually.
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(printable_x_max/2)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(printable_y_max/2)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	DEBUG_ECHO PREFIX="VAOC_START" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, zcontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_x_offset VALUE={svv.idex_xoffset|default(0.0)|float}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_y_offset VALUE={svv.idex_yoffset|default(0.0)|float}
	
	
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_SAFE_Z_HEIGHT
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_speed VALUE={printer["gcode_macro RatOS"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_accel VALUE={printer["gcode_macro RatOS"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_zhop VALUE={printer["gcode_macro RatOS"].toolchange_zhop|float}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE=0
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"START X_REFERENCE:%.6f Y_REFERENCE:%.6f Z_REFERENCE:%.6f PARK_T0:%.6f PARK_T1:%.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, parking_position_t0, parking_position_t1)}
	
	
	_LED_VAOC_ON
	
	
	
	
	
	
	
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=gcode_z_offset VALUE={printer.gcode_move.homing_origin.z}
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z=0
	
	
	MAYBE_HOME
	M400
	
	
	_LOAD_RATOS_SKEW_PROFILE
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	IDEX_SINGLE
	{% endif %}
	
	
	
	SAVE_GCODE_STATE NAME=vaoc_state
	
	
	RESET_NAMED_OFFSET EVENT=reset_all
	
	
	{% if is_fixed %}
	_SELECT_TOOL T=0 TOOLSHIFT=false
	{% if default_toolhead == 0 %}
	G1 X{idex_xcontrolpoint} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint + safe_distance + additional_safe_distance} F{speed}
	{% else %}
	G1 X{idex_xcontrolpoint - safe_distance - additional_safe_distance} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint} F{speed}
	{% endif %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	{% else %}
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	G1 X{idex_xcontrolpoint} F{speed}
	G1 Y{idex_ycontrolpoint} F{speed}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	
	
	_SELECT_TOOL T={default_toolhead} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	{% if not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={default_toolhead}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=True

[gcode_macro _VAOC_END]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_y = printable_y_max / 2 %}
	{% set saved_gcode_z_offset = printer["gcode_macro _VAOC"].gcode_z_offset|default(0.0)|float %}
	
	DEBUG_ECHO PREFIX="_VAOC_END" MSG="printable_y_max: {printable_y_max}, center_y: {center_y}, safe_z: {safe_z}"
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% set x_offset_change = svv.idex_xoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_x_offset|default(0.0)|float %}
	{% set y_offset_change = svv.idex_yoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_y_offset|default(0.0)|float %}
	{% set offset_change_norm = (x_offset_change ** 2 + y_offset_change ** 2) ** 0.5 %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="VAOC calibration changed the relative XY offset between T0 and T1 by {offset_change_norm|round(3)} mm (ΔX: {x_offset_change|round(3)}, ΔY: {y_offset_change|round(3)})"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	G1 Y{center_y} F{speed}
	
	
	_IDEX_SINGLE INIT=1
	
	
	_LED_VAOC_OFF
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={printer["gcode_macro _VAOC"].cache_toolchange_zhop|float}
	
	
	{% if printer["gcode_macro _VAOC"].is_started_at_temp|default(true)|lower == 'true' %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_bowden_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_bowden_sensor_enabled|int}
	{% endif %}
	{% endif %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro _VAOC"].loaded_skew_profile|default("") %}
	{% if loaded_skew_profile != "" %}
	SKEW_PROFILE LOAD={loaded_skew_profile}
	{% else %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=vaoc_state
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z={saved_gcode_z_offset}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False

[gcode_macro _VAOC_LOAD_TOOL]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set auto_temp_offset = true if params.AUTO_TEMP_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set toolhead_zoffset = svv.idex_zoffset|default(0)|float %}
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move T%s to control point: X%.6f Y%.6f Z%.6f IS_FIXED=%s"' % (t, idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, is_fixed)}
	
	
	{% if not auto_temp_offset and not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={t}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	{% set current_z = printer.toolhead.position.z|float %}
	{% set lowest_toolhead_z = [current_z, current_z - toolhead_zoffset]|min %}
	{% if lowest_toolhead_z < safe_z %}
	G1 Z{[safe_z, safe_z + toolhead_zoffset]|max} F{z_speed}
	{% else %}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	{% endif %}
	
	
	_SELECT_TOOL T={t} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_SET_CAMERA_COOLING]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	
	
	{% set enable_camera_cooling = true if printer["gcode_macro _VAOC"].enable_camera_cooling|default(true)|lower == 'true' else false %}
	{% set camera_cooling_temperature = printer["gcode_macro _VAOC"].camera_cooling_temperature|float %}
	{% set camera_cooling_fan_speed = printer["gcode_macro _VAOC"].camera_cooling_fan_speed|float %}
	
	
	{% if printer.heater_bed.temperature >= camera_cooling_temperature and enable_camera_cooling %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={camera_cooling_fan_speed if t == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={camera_cooling_fan_speed if t == 1 else 0}
	
	
	M106.1 S{camera_cooling_fan_speed}
	
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	{% endif %}

[gcode_macro _VAOC_SET_TOOL]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="_VAOC_SET_TOOL" MSG="IDEX_MODE: {idex_mode}, TOOLHEAD: {toolhead}"
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	{% set x = printer.gcode_move.gcode_position.x|float %}
	{% set y = printer.gcode_move.gcode_position.y|float %}
	{% set z = printer.gcode_move.gcode_position.z|float %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE={x}
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE={y}
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE={z}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Control point was set: X%.6f Y%.6f Z%.6f"' % (x, y, z)}
	
	{% else %}
	
	
	
	{% set move_diff_x = printer.gcode_move.gcode_position.x|float - svv.idex_xcontrolpoint|float %}
	{% set move_diff_y = printer.gcode_move.gcode_position.y|float - svv.idex_ycontrolpoint|float %}
	{% set move_diff_z = printer.gcode_move.gcode_position.z|float - svv.idex_zcontrolpoint|float %}
	
	
	{% set new_x_offset = svv.idex_xoffset - move_diff_x %}
	{% set new_y_offset = svv.idex_yoffset - move_diff_y %}
	{% set new_z_offset = svv.idex_zoffset - move_diff_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE={new_x_offset}
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE={new_y_offset}
	
	{% set z_focus_msg = "" %}
	{% if move_diff_z|abs > 1e-6 %}
	{% if printer["gcode_macro _VAOC"].adjusting_secondary_toolhead_focus_adjusts_zoffset|default(false)|lower == 'true' %}
	{% set z_focus_msg = " (Z offset adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={new_z_offset}
	{% else %}
	{% set z_focus_msg = " (Z offset not adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	{% set new_z_offset = svv.idex_zoffset %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset was set: X%.6f Y%.6f Z%.6f%s"' % (toolhead, new_x_offset, new_y_offset, new_z_offset, z_focus_msg)}
	
	{% endif %}

[gcode_macro _VAOC_MOVE]
gcode = 
	
	{% set x = params.X|default(0)|float %}
	{% set y = params.Y|default(0)|float %}
	{% set z = params.Z|default(0)|float %}
	
	
	G91
	{% if z != 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 Z%.6f F300"' % (z)}
	G1 Z{z} F300
	
	{% else %}
	{% if x <=2 and y <=2 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 X%.6f Y%.6f F18000"' % (x, y)}
	G1 X{x} Y{y} F18000
	{% endif %}
	{% endif %}
	G90

[gcode_macro _VAOC_CALIBRATE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	{% if printer["z_offset_probe"] is defined and is_started %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	
	{% if auto_z_offset %}
	_START_VAOC AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_END
	{% else %}
	_VAOC_LOAD_TOOL T={default_toolhead}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	{% endif %}
	
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_Z_OFFSET
	
	{% endif %}

[gcode_macro _VAOC_PROBE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}
	{% if not auto_z_offset %}
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	{% endif %}
	M400
	_VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT

[gcode_macro _VAOC_Z_OFFSET_PROBE_CURRENT_POSITION]
gcode = 
	
	Z_OFFSET_PROBE PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_DROP=1 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median

[gcode_macro _VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT]
gcode = 
	{% if printer["z_offset_probe"] is defined %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE={last_z}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Z-offset control point set:: %.6f"' % last_z}
	
	{% else %}
	
	
	
	{% set z = svv.idex_zoffsetcontrolpoint|float - last_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={z}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-z)}
	
	
	G0 Z{svv.idex_zcontrolpoint|float} F{z_speed}
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset set: Z %.6f"' % (t, z)}
	
	{% endif %}
	
	{% endif %}

[gcode_macro _VAOC_ECHO_Z_OFFSET]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s toolhead z-offset %.6f"' % (1 if default_toolhead == 0 else 0, svv.idex_zoffset)}
	{% if svv.idex_zoffset|abs < 0.02 %}
	CONSOLE_ECHO TITLE={'"Perfect toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="You have a perfect toolhead z-offset!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.02 and svv.idex_zoffset|abs < 0.05 %}
	CONSOLE_ECHO TITLE={'"Good toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is good!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.05 and svv.idex_zoffset|abs < 0.1 %}
	CONSOLE_ECHO TITLE={'"High toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset could be better._N_Use minimum 0.3mm first layer height for copy and mirror mode prints." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.1 and svv.idex_zoffset|abs < 0.2 %}
	CONSOLE_ECHO TITLE={'"Bad toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is bad._N_Copy and mirror mode prints are not recommended with it." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.2 %}
	CONSOLE_ECHO TITLE={'"Unacceptable toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is unacceptable._N_Do not print in copy and mirror mode with it." TYPE="alert"
	{% endif %}
	RATOS_ECHO PREFIX="VAOC" MSG="Toolhead z-offset calibration done!"

[gcode_macro _VAOC_CALIBRATE_TEMP_OFFSET]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if is_fixed and is_started and printer["z_offset_probe"] is defined and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	_VAOC_LOAD_TOOL T={default_toolhead} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_NOZZLE_TEMP_OFFSETS
	
	{% endif %}

[gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET=0
	
	
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	M400

[gcode_macro _VAOC_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(150)|float %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Probing with nozzle temperature {temp}°C..."
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	
	
	G0 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _VAOC_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set msg = '"T0 expansion coefficient %.6fmm_N_T1 expansion coefficient %.6fmm"' % (svv.nozzle_expansion_coefficient_t0, svv.nozzle_expansion_coefficient_t1) %}
	CONSOLE_ECHO TITLE="Nozzle expansion coefficients:" MSG={msg} TYPE="success"

[gcode_macro _VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - expected_camera_x_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC x-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_xcontrolpoint, expected_camera_x_position)) }
	{% endif %}
	{% if (idex_ycontrolpoint - expected_camera_y_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC y-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_ycontrolpoint, expected_camera_y_position)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - printer.gcode_move.gcode_position.x|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected y-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_xcontrolpoint, printer.gcode_move.gcode_position.x|float)) }
	{% endif %}
	{% if (idex_ycontrolpoint - printer.gcode_move.gcode_position.y|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected x-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_ycontrolpoint, printer.gcode_move.gcode_position.y|float)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_SAFE_Z_HEIGHT]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set idex_zoffsetcontrolpoint = svv.idex_zoffsetcontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_SAFE_Z_HEIGHT" MSG={'"idex_zcontrolpoint: %.6f, idex_zoffsetcontrolpoint: %.6f"' % (idex_zcontrolpoint, idex_zoffsetcontrolpoint)}
	
	{% if safe_z < idex_zcontrolpoint + 2 or safe_z < idex_zoffsetcontrolpoint + 2 %}
	{action_raise_error("VAOC safe_z value (%.3f) is too low, it must be higher than %.3f" % (safe_z, [idex_zoffsetcontrolpoint + 2, idex_zcontrolpoint + 2]|max))}
	{% endif %}

[gcode_macro _VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED]
gcode = 
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T0. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T1. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_RESET]
gcode = 
	DEBUG_ECHO PREFIX="_VAOC_RESET" MSG="running template-emitted _VAOC_RESET macro"
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE=212.5
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE=530.5
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE=10
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE=0
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE=0.0
	
	RESET_DC_ENDSTOP_CONFIGURATION
	RESET_Y_MAX_ADJUSTMENT
	
	
	CONSOLE_ECHO TITLE="VAOC Configuration Reset" MSG="VAOC configuration has been reset. You must RESTART klipper for the changes to take effect,_N_then re-calibrate VAOC."

[gcode_macro _ECHO_VAOC_VARS]
description = Echo VAOC variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro _VAOC"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro _VAOC_SWITCH_LED]
gcode = 
	{% if params.STATE|default(0)|int == 1 %}
	_LED_VAOC_ON
	{% else %}
	_LED_VAOC_OFF
	{% endif %}

[gcode_macro Z_PROBE_TEST_T0]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T0
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST_T1]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T1
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	
	
	_VAOC_Z_PROBE_TEST_EVALUATE
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro _VAOC_Z_PROBE_LOOP]
gcode = 
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_SHAKE_IT
	_VAOC_START

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if primary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T0. Retried {primary_retries} time(s)."
	{% endif %}
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	
	{% if (primary_range - secondary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 is drifting significantly more than T1."
	{% endif %}
	{% if (secondary_range - primary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 is drifting significantly more than T0."
	{% endif %}
	
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T0]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T1]
gcode = 
	
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _SHAKE_IT]
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	_Z_HOP
	{% for i in range(3) %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 + 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 + 1}
	{% endfor %}
	{% for i in range(2) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 + 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 + 50}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 1}
	{% endfor %}
	{% endfor %}

[gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 retries updated: {new_retries}"

[gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 retries updated: {new_retries}"

[gcode_macro _CLEAR_PRIMARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _CLEAR_SECONDARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _VAOC_TEST_Z_OFFSET]
gcode = 
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}

[delayed_gcode _IDEX_INIT]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	VERIFY_HYBRID_INVERTED

[gcode_macro Z_TILT_ADJUST]
rename_existing = Z_TILT_ADJUST_ORIG
gcode = 
	
	{% set beacon_contact_z_tilt_adjust_samples = printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust_samples|default(2)|int %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(true)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	_IDEX_SINGLE
	
	_SELECT_TOOL T={printer["gcode_macro RatOS"].default_toolhead|default(0)|int} TOOLSHIFT=false
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_tilt_adjust %}
	Z_TILT_ADJUST_ORIG PROBE_METHOD=contact SAMPLES={beacon_contact_z_tilt_adjust_samples}
	{% else %}
	Z_TILT_ADJUST_ORIG
	{% endif %}
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if idex_mode == "copy" %}
	_IDEX_COPY
	{% elif idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[stepper_x]
position_max = 500
position_endstop = -59.6
position_min = -59.6
step_pin = PF13
dir_pin = x_dir_pin
enable_pin = !PF14
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t0:PA2

[stepper_y]
position_max = 533.65
position_min = -14.35
position_endstop = -14.35
step_pin = PG0
dir_pin = !y_dir_pin
enable_pin = !PF15
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = PG9

[stepper_z]
position_max = 500
position_min = -7
step_pin = PC13
dir_pin = !z0_dir_pin
enable_pin = !PF1
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4
homing_speed = 10
endstop_pin = probe:z_virtual_endstop

[z_tilt]
z_positions = 
	0,0
	250,500
	500,0
points = 
	20, 10
	480, 230
	20, 450
horizontal_move_z = 20
retries = 10
retry_tolerance = 0.02
speed = 600

[extruder]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t0:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t0:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t0:PD3
dir_pin = toolboard_t0:e_dir_pin
enable_pin = !toolboard_t0:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[firmware_retraction]
retract_speed = 60
unretract_extra_length = 0
unretract_speed = 60
retract_length = 0.2

[extruder1]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t1:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t1:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t1:PD3
dir_pin = toolboard_t1:e_dir_pin
enable_pin = !toolboard_t1:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[resonance_tester]
accel_chip_x = lis2dw toolboard_t0
accel_chip_y = lis2dw toolboard_t0
probe_points = 
	250,250,20

[tmc5160 stepper_x]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC4
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 dual_carriage]
stealthchop_threshold = 0
interpolate = True
cs_pin = PF2
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y]
stealthchop_threshold = 0
interpolate = True
cs_pin = PD11
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y1]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC7
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[stepper_y1]
step_pin = PG4
dir_pin = y1_dir_pin
enable_pin = !PA2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46

[tmc2209 stepper_z]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE4
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[tmc2209 stepper_z1]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE1
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z1]
step_pin = PE2
dir_pin = !z1_dir_pin
enable_pin = !PD4
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 stepper_z2]
stealthchop_threshold = 0
interpolate = True
uart_pin = PD3
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z2]
step_pin = PE6
dir_pin = !z2_dir_pin
enable_pin = !PE0
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 extruder]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t0:PB3
run_current = 0.707
sense_resistor = 0.11

[tmc2209 extruder1]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t1:PB3
run_current = 0.707
sense_resistor = 0.11

[beacon]
serial = /dev/beacon
x_offset = 0
y_offset = 27.5
mesh_main_direction = x
mesh_runs = 1
mesh_cluster_size = 0
speed = 15.
lift_speed = 80.
contact_max_hotend_temperature = 275
contact_mesh_min = 20,20
contact_mesh_max = 480,480

[beacon_user_z_offset]

[beacon_mesh]

[beacon_true_zero_correction]

[beacon_adaptive_heat_soak]

[delayed_gcode _BEACON_INIT]
initial_duration = 1
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	_BEACON_MESH_INIT
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_coefficient_multiplier
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_applied_offset
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=beacon_saved_runtime_offset
	{% if printer["gcode_macro RatOS"].beacon_contact_expansion_multiplier is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_contact_expansion_multiplier is no longer used, please remove it from your config file."
	{% endif %}
	{% if printer["gcode_macro RatOS"].beacon_scan_compensation_resolution is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_scan_compensation_resolution is no longer used, please remove it from your config file."
	{% endif %}

[gcode_macro BEACON_RATOS_CALIBRATION]
gcode = 
	RATOS_ECHO MSG="Did you mean BEACON_RATOS_CALIBRATE?"

[gcode_macro BEACON_RATOS_CALIBRATE]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	BEACON_INITIAL_CALIBRATION _AUTOMATED=True
	
	{% if beacon_contact_start_print_true_zero %}
	BEACON_POKE_TEST _AUTOMATED=True
	_BEACON_CHECK_POKE
	{% if printer["dual_carriage"] is not defined %}
	BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET _AUTOMATED=True
	{% endif %}
	{% endif %}
	
	{% set already_heated = False %}
	
	
	{% if beacon_contact_start_print_true_zero and beacon_scan_compensation_enable %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% set already_heated = True %}
	{% endif %}
	
	
	BEACON_FINAL_CALIBRATION _AUTOMATED=True _AUTOMATED_ALREADY_HEATED={already_heated} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	{% if beacon_contact_start_print_true_zero %}
	{% if printer["dual_carriage"] is not defined %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	_BEACON_ECHO_POKE
	{% endif %}
	RATOS_ECHO MSG="Beacon calibration finished!"
	
	
	_LED_BEACON_CALIBRATION_END
	
	
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG

[gcode_macro BEACON_INITIAL_CALIBRATION]
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Initial beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro BEACON_FINAL_CALIBRATION]
description = Runs BEACON_AUTO_CALIBRATE after heating the bed and chamber to specified temperatures. This creates a beacon model under reference conditions for future use.
	This macro will skip calibration if both the beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero settings are enabled, because a new
	model will be calibrated automatically at the start of each print. Use FORCE=True to override this check.
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set already_heated = true if params._AUTOMATED_ALREADY_HEATED|default(false)|lower == 'true' else false %}
	{% set force = params.FORCE|default('false')|lower in ('1', 'true', 'yes') %}
	
	
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default('false')|lower == "true" %}
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero and not force %}
	RATOS_ECHO MSG="BEACON_FINAL_CALIBRATION skipped, not needed because beacon_contact_calibrate_model_on_true_zero is enabled. Use FORCE=True to override."
	{% else %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	{% if chamber_temp > 0 and not already_heated %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	{% if not already_heated %}
	
	G0 Z2.5 F{z_hop_speed}
	
	
	RATOS_ECHO MSG="Waiting for calibration temperature..."
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	{% if beacon_adaptive_heat_soak %}
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,3600]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_Z_HOP
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Final beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	{% endif %}

[gcode_macro BEACON_POKE_TEST]
variable_poke_result_1 = -1
variable_poke_result_2 = -1
variable_poke_result_3 = -1
variable_poke_result_4 = -1
variable_poke_result_5 = -1
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_1 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_2 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_3 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_4 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_5 VALUE=-1
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G0 Z5 F{z_hop_speed}
	
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=1
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=2
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=3
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=4
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=5
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Beacon poke test finished!"
	{% if not automated %}
	_BEACON_ECHO_POKE
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro _BEACON_PROBE_POKE]
gcode = 
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	BEACON_POKE speed=3 top=5 bottom={poke_bottom}
	BEACON_QUERY

[gcode_macro _BEACON_STORE_POKE]
gcode = 
	
	{% set i = params.I|default(1)|int %}
	
	
	{% set last_z = printer.beacon.last_poke_result|default(0)|float %}
	
	
	{% if printer.beacon.last_poke_result|lower != "none" %}
	{% if printer.beacon.last_poke_result.error == 0 %}
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE={"poke_result_%s" % i} VALUE={printer.beacon.last_poke_result.latency}
	{% endif %}
	{% endif %}

[gcode_macro _BEACON_CHECK_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% if p1 == -1 or p2 == -1 or p3 == -1 or p4 == -1 or p5 == -1 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test error!") }
	{% endif %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	{% if avg > 6 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test failed!") }
	{% endif %}

[gcode_macro _BEACON_ECHO_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	
	
	{% if avg <= 1 %}
	{% set type = "success" %}
	{% set note = "Extremely low noise, rarely achieved" %}
	{% elif avg > 1 and avg <= 4 %}
	{% set type = "info" %}
	{% set note = "Excellent performance for a typical printer" %}
	{% elif avg > 4 and avg <= 8 %}
	{% set type = "warning" %}
	{% set note = "Acceptable performance, machine may have considerable cyclic axis noise" %}
	{% elif avg > 8 and avg <= 11 %}
	{% set type = "alert" %}
	{% set note = "Not ideal, may want to verify proper mounting or use thinner stackups" %}
	{% elif avg > 11 %}
	{% set type = "alert" %}
	{% set note = "Reason for concern, present setup may be risky to continue with" %}
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon poke test result:" TYPE={type} MSG={'"Average latency: %.2f_N_%s"' % (avg, note)}

[gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Nozzle temperature offset calibration..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET=0
	
	
	{% if not automated %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing with nozzle temperature {temp}°C..."
	PROBE PROBE_METHOD=contact PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median
	BEACON_QUERY
	
	
	G0 Z5 F{z_speed}

[gcode_macro _BEACON_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer.beacon.last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{default_toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% if default_toolhead == 0 %}
	CONSOLE_ECHO TYPE="info" MSG={'"T0 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t0}
	{% else %}
	CONSOLE_ECHO TYPE="info" MSG={'"T1 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t1}
	{% endif %}

[gcode_macro _BEACON_SET_NOZZLE_TEMP_OFFSET]
description = "Set the thermal expansion z offset for the active toolhead based on the current extruder target temperature and thermal expansion coefficient."
gcode = 
	{% if params.RESET is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The RESET parameter is no longer supported and has no effect."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% if params.TOOLHEAD is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The TOOLHEAD parameter is no longer supported and has no effect. The macro now automatically determines the current toolhead."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	{% if beacon_contact_expansion_compensation %}
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set nozzle_expansion_coefficient_t0 = svv.nozzle_expansion_coefficient_t0|default(0)|float %}
	{% if printer["dual_carriage"] is defined %}
	{% set nozzle_expansion_coefficient_t1 = svv.nozzle_expansion_coefficient_t1|default(0)|float %}
	{% endif %}
	
	
	{% set temp = printer['extruder' if toolhead == 0 else 'extruder1'].target|float %}
	
	
	{% set temp_delta = temp - beacon_contact_true_zero_temp %}
	{% set expansion_coefficient = nozzle_expansion_coefficient_t0 if toolhead == 0 else nozzle_expansion_coefficient_t1 %}
	{% set expansion_offset = temp_delta * (expansion_coefficient / 100) %}
	
	
	SET_NAMED_OFFSET NAME=hotend_thermal_expansion Z={expansion_offset} MOVE=1 MOVE_SPEED={z_speed}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG={'"Nozzle expansion offset of %.6fmm applied to T%s"' % (expansion_offset, toolhead)}
	DEBUG_ECHO PREFIX="_BEACON_SET_NOZZLE_TEMP_OFFSET" MSG="toolhead: {toolhead}, coefficient: {expansion_coefficient|round(6)}, temp_delta: {temp_delta|round(1)},  expansion_offset: {expansion_offset|round(6)}"
	
	{% endif %}

[gcode_macro BEACON_MEASURE_BEACON_OFFSET]
variable_needs_compensation = False
variable_reference_z = 0.0
variable_front = 0.0
variable_front_left = 0.0
variable_front_right = 0.0
variable_back = 0.0
variable_back_left = 0.0
variable_back_right = 0.0
variable_right = 0.0
variable_left = 0.0
variable_margin_x = 40
variable_margin_y = 40
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=False
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Measure beacon offset..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="center"
	
	
	G0 X{margin_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_left"
	
	
	G0 X{safe_home_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front"
	
	
	G0 X{(printable_x_max - margin_x)} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_right"
	
	
	G0 X{safe_home_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back"
	
	
	G0 X{margin_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_left"
	
	
	G0 X{margin_x} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="left"
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_BEACON_ECHO_BEACON_OFFSET
	
	
	_LED_BEACON_CALIBRATION_END
	
	{% endif %}

[gcode_macro _BEACON_STORE_BEACON_OFFSET]
gcode = 
	
	{% set location = params.LOCATION|lower %}
	
	
	{% set last_z = printer.beacon.last_offset_result["delta"]|default(0)|float %}
	
	
	{% if location == "center" %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE={location} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_BEACON_OFFSET]
gcode = 
	
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float * 1000 %}
	{% set front_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_left|default(0)|float * 1000 %}
	{% set front = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front|default(0)|float * 1000 %}
	{% set front_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_right|default(0)|float * 1000 %}
	{% set right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].right|default(0)|float * 1000 %}
	{% set back_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_right|default(0)|float * 1000 %}
	{% set back = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back|default(0)|float * 1000 %}
	{% set back_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_left|default(0)|float * 1000 %}
	{% set left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].left|default(0)|float * 1000 %}
	
	{% set line_1 = "Front left:    %.6fμm" % (front_left) %}
	{% set line_2 = "Front center:  %.6fμm" % (front) %}
	{% set line_3 = "Front right:   %.6fμm" % (front_right) %}
	{% set line_4 = "Left center:   %.6fμm" % (left) %}
	{% set line_5 = "Right center:  %.6fμm" % (right) %}
	{% set line_6 = "Back left:     %.6fμm" % (back_left) %}
	{% set line_7 = "Back center:   %.6fμm" % (back) %}
	{% set line_8 = "Back right:    %.6fμm" % (back_right) %}
	
	{% set max_value = [(front_left|abs), (front|abs), (front_right|abs), (left|abs), (right|abs), (back_left|abs), (back|abs), (back_right|abs)]|max %}
	{% if max_value <= 50 %}
	{% set type = "success" %}
	{% set recommendation = "Very low beacon offset: %.6fμm._N_No beacon scan compensation needed." % max_value %}
	{% elif max_value > 50 and max_value <= 100 %}
	{% set type = "info" %}
	{% set recommendation = "Low beacon offset: %.6fμm._N_You may experience first layer inconsistensies, consider beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 100 and max_value <= 150 %}
	{% set type = "warning" %}
	{% set recommendation = "High beacon offset: %.6fμm._N_High chance of first layer problems, beacon scan compensation is highly encouraged." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 150 and max_value <= 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Very High beacon offset: %.6fμm._N_You will encounter first layer problems on large prints unless you activate beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Extremely high beacon offset: %.6fμm._N_You have significant scan/contact inconsistency which is indicative of mechanical problems, please investigate before resorting to software compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon offset relative to the center" TYPE={type} MSG={'"_N_%s_N__N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s"' % (recommendation, line_1, line_2, line_3, line_4, line_5, line_6, line_7, line_8)}

[gcode_macro BEACON_CREATE_SCAN_COMPENSATION_MESH]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set profile = params.PROFILE|default("auto")|string %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set keep_temp_meshes = params.KEEP_TEMP_MESHES|default(0) %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' %}
	{% set desired_spacing = printer["gcode_macro RatOS"].beacon_scan_compensation_desired_spacing|float %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	
	{% if not beacon_scan_compensation_enable %}
	RATOS_ECHO MSG="Beacon scan compensation is disabled!"
	
	{% else %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	
	
	RATOS_ECHO MSG="Please wait..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	G1 Z2.5 F{z_speed}
	{% if beacon_adaptive_heat_soak %}
	
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,9000]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if not (beacon_adaptive_heat_soak or bed_heat_soak_time > 0) %}
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if printer.z_tilt is defined %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% endif %}
	{% if printer.quad_gantry_level is defined %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% endif %}
	
	
	_BEACON_CREATE_SCAN_COMPENSATION_MESH_CORE PROFILE="{profile}" DESIRED_SPACING={desired_spacing} CHAMBER_TEMP={chamber_temp} KEEP_TEMP_MESHES={keep_temp_meshes}
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	{% if automated %}
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon scan compensation mesh created!"
	
	
	{% if not automated %}
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED]
gcode = 
	
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED" MSG="beacon_scan_compensation_profile {beacon_scan_compensation_profile}, beacon_scan_compensation_enable {beacon_scan_compensation_enable}"
	
	{% if beacon_scan_compensation_enable %}
	BEACON_APPLY_SCAN_COMPENSATION PROFILE="{beacon_scan_compensation_profile}"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL]
gcode = 
	
	{% set beacon_contact_start_print_true_zero = params.BEACON_CONTACT_START_PRINT_TRUE_ZERO|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = params.beacon_contact_calibrate_model_on_true_zero|lower == 'true' %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and not printer.beacon.model %}
	{% set beacon_model_required_for_true_zero = beacon_contact_start_print_true_zero and not beacon_contact_calibrate_model_on_true_zero %}
	{% set beacon_model_required_for_homing =
	printer.fastconfig.settings.stepper_z.endstop_pin == 'probe:z_virtual_endstop'
	and (( printer.fastconfig.settings.beacon.home_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower != 'true')
	or ( printer.fastconfig.settings.beacon.default_probe_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower != 'true' )) %}
	{% if beacon_model_required_for_homing or beacon_model_required_for_true_zero %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("An active Beacon model is required. Have you performed initial Beacon calibration?") }
	{% endif %}
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION]
gcode = 
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set bed_temp_mismatch_is_error = true if printer["gcode_macro RatOS"].beacon_scan_compensation_bed_temp_mismatch_is_error|default(false)|lower == 'true' else false %}
	
	{% set bed_temp = params.BED_TEMP|default(0)|float %}
	{% if bed_temp == 0 %}
	{% set bed_temp = printer.heater_bed.temperature %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_PREFLIGHT_CHECK_BEACON" MSG="beacon_scan_compensation_profile={beacon_scan_compensation_profile}, beacon_scan_compensation_enable={beacon_scan_compensation_enable}, bed_temp={bed_temp}"
	
	{% if beacon_scan_compensation_enable %}
	_VALIDATE_COMPENSATION_MESH_PROFILE PROFILE="{beacon_scan_compensation_profile}" TITLE="Check Beacon scan compensation profile" SUBJECT="Configured compensation profile '{beacon_scan_compensation_profile}'" COMPARE_BED_TEMP={bed_temp} COMPARE_BED_TEMP_IS_ERROR={bed_temp_mismatch_is_error}
	{% endif %}

[gcode_macro _BEACON_MAYBE_SCAN_COMPENSATION]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set needs_scan_compensation = true if printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].needs_compensation|default(false)|lower == 'true' else false %}
	
	{% if needs_scan_compensation %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% endif %}

[gcode_macro _BEACON_HOME_AND_ABL]
gcode = 
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	{% if needs_rehoming %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}

[gcode_macro SAVE_Z_OFFSET]
description = Deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead, or in Mainsail use the SAVE button in the Z-OFFSET section.
gcode = 
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default('false')|lower == 'true' %}
	{% set msg = "SAVE_Z_OFFSET is deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead,_N_or in Mainsail use the SAVE button in the Z-OFFSET section."%}
	{% if not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% set msg = msg + "_N_You must then use the SAVE_CONFIG command to persist the change." %}
	{% endif %}
	CONSOLE_ECHO TYPE="error" MSG="{msg}"

[gcode_macro _BEACON_OFFSET_COMPARE]
gcode = 
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing..."
	
	
	BEACON_OFFSET_COMPARE SAMPLES_DROP=1 SAMPLES=3
	BEACON_QUERY

[fan]
pin = rpi:gpio4

[fan_generic part_fan_t0]
pin = PA8
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[fan_generic part_fan_t1]
pin = PE5
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[heater_fan toolhead_cooling_fan_t0]
heater = extruder
shutdown_speed = 1
pin = toolboard_t0:PB4

[heater_fan toolhead_cooling_fan_t1]
heater = extruder1
shutdown_speed = 1
pin = toolboard_t1:PB4

[controller_fan controller_fan]
pin = dinghy:PA4
tachometer_pin = dinghy:PC15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[z_offset_probe]
pin = ^PG10
z_offset = -7
y_offset = 0
x_offset = 37.5
speed = 10
samples = 3
sample_retract_dist = 5
lift_speed = 10.0
samples_result = median
samples_tolerance = 0.2
samples_tolerance_retries = 5

[neopixel vaoc_led]
pin = PB10
chain_count = 6
color_order = GRB

[heater_fan vaoc_fan]
pin = PD13
heater = heater_bed
fan_speed = 1.0
heater_temp = 50

[fan_generic filter]
pin = !PD14
enable_pin = PD15

[gcode_macro T0]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = True
variable_color = "7bff33"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = -32.6
variable_parking_position = -57.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=0 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[gcode_macro T1]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = False
variable_color = "0ea5e9"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = 532.6
variable_parking_position = 557.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=1 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[save_variables]
filename = /home/pi/printer_data/config/ratos-variables.cfg

[mcu dinghy]
serial = /dev/serial/by-id/usb-Klipper_stm32f072xb_Dragon_dinghy-if00

[temperature_sensor th0]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA0

[temperature_sensor th1]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA1

[temperature_sensor th2]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA2

[temperature_sensor th3]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA3

[controller_fan CTL2]
pin = dinghy:PB14
tachometer_pin = dinghy:PB15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[mcu plasma]
serial = /dev/serial/by-id/usb-Klipper_rp2040_Plasma-if00

[neopixel Chamber_Lights]
pin = plasma:gpio15
chain_count = 140
color_order = GRBW
initial_red = 0.0
initial_green = 0.0
initial_blue = 0.0
initial_white = 0.1

[beacon model default]
model_coef = 1.5287863993594841,
	1.9289099639750602,
	0.8838828622507556,
	0.25554883784260735,
	-0.015171504024913506,
	0.3044946127013882,
	0.15820427856566457,
	-0.25262403959326246,
	0.042488512846660914,
	0.16662470122520964
model_domain = 1.842634574664148e-07,1.9339206373083917e-07
model_range = 0.200000,5.000000
model_temp = 13.222247
model_offset = 0.00000

[bed_mesh default]
version = 1
points = 
	0.016163, 0.016713, 0.001923, -0.017658, -0.031574, -0.032498, -0.030898, -0.032177, -0.035213, -0.031148, -0.021322, -0.016924, -0.015012, -0.013911, -0.012197, -0.012583, -0.010489, -0.007529, -0.003986, -0.000980, 0.005518, 0.014442, 0.027426, 0.034677, 0.037410, 0.040391, 0.041842, 0.040369, 0.037615, 0.030776, 0.027664, 0.022856, 0.016892, 0.015398, 0.014717, 0.006921, 0.001532, 0.000731, 0.008657, 0.014036
	0.005356, -0.005066, -0.016998, -0.029668, -0.038334, -0.043672, -0.041139, -0.042488, -0.045199, -0.039432, -0.028746, -0.023642, -0.024058, -0.022802, -0.019679, -0.018514, -0.018102, -0.016476, -0.012722, -0.010077, -0.001809, 0.007180, 0.019853, 0.027754, 0.029964, 0.033626, 0.036783, 0.032018, 0.029372, 0.020847, 0.017634, 0.011926, 0.009013, 0.009254, 0.007972, -0.001380, -0.006940, -0.002160, 0.006135, 0.008330
	-0.004900, -0.006720, -0.021914, -0.039691, -0.050459, -0.050377, -0.046281, -0.048755, -0.054708, -0.051499, -0.033927, -0.027632, -0.030243, -0.031447, -0.024387, -0.021408, -0.020382, -0.018068, -0.015930, -0.013877, -0.006099, 0.003479, 0.013310, 0.024783, 0.025522, 0.030849, 0.033573, 0.031409, 0.025495, 0.016683, 0.011264, 0.008805, 0.006856, 0.008059, 0.007305, 0.002581, -0.003320, -0.003239, 0.004691, 0.010045
	-0.008791, -0.019334, -0.029149, -0.040533, -0.051698, -0.058235, -0.054863, -0.054840, -0.055692, -0.049534, -0.036731, -0.033053, -0.035667, -0.035315, -0.024352, -0.023825, -0.022538, -0.020438, -0.018207, -0.015389, -0.006515, 0.001966, 0.013591, 0.019434, 0.020600, 0.024967, 0.029425, 0.026812, 0.018980, 0.007878, 0.002360, 0.000859, 0.003849, 0.005649, 0.005421, -0.000416, -0.007906, -0.003164, 0.007582, 0.010039
	-0.018512, -0.018210, -0.033932, -0.050501, -0.061588, -0.064139, -0.060236, -0.062528, -0.067065, -0.062039, -0.045815, -0.039448, -0.040521, -0.042080, -0.033870, -0.030878, -0.027396, -0.024548, -0.021298, -0.020041, -0.011880, -0.002847, 0.008689, 0.015857, 0.015934, 0.018697, 0.022439, 0.022106, 0.017916, 0.005879, 0.001037, -0.001311, -0.001335, 0.001897, 0.003656, 0.000561, -0.006084, -0.005683, 0.000338, 0.006245
	-0.028558, -0.036721, -0.044680, -0.054969, -0.066140, -0.075045, -0.073515, -0.073161, -0.075696, -0.068963, -0.058892, -0.053111, -0.050990, -0.048040, -0.041262, -0.037419, -0.034866, -0.031845, -0.029787, -0.026524, -0.017896, -0.009322, -0.001010, 0.005819, 0.008058, 0.010456, 0.013266, 0.012529, 0.007992, -0.001491, -0.006769, -0.009303, -0.005980, -0.003567, -0.003340, -0.011496, -0.018818, -0.014808, -0.004181, -0.000733
	-0.037253, -0.038393, -0.053129, -0.066170, -0.075959, -0.079233, -0.077475, -0.082688, -0.086779, -0.083983, -0.069005, -0.062542, -0.060351, -0.058481, -0.051101, -0.043149, -0.039837, -0.037039, -0.034698, -0.031301, -0.024330, -0.019786, -0.010285, -0.001967, 0.002812, 0.004899, 0.009657, 0.006946, 0.002155, -0.005232, -0.009851, -0.011218, -0.011509, -0.010097, -0.010293, -0.013175, -0.018958, -0.019846, -0.012107, -0.005641
	-0.046584, -0.055590, -0.062606, -0.069218, -0.080399, -0.087414, -0.089037, -0.092376, -0.095115, -0.088957, -0.080802, -0.073290, -0.068741, -0.064591, -0.054452, -0.048270, -0.045916, -0.044559, -0.042047, -0.039605, -0.032667, -0.025789, -0.019495, -0.012773, -0.006697, -0.003025, 0.001413, 0.000817, -0.004738, -0.013008, -0.017605, -0.018191, -0.018524, -0.016356, -0.016750, -0.021992, -0.028943, -0.025791, -0.016146, -0.010447
	-0.051029, -0.051677, -0.068218, -0.079622, -0.088590, -0.089331, -0.089731, -0.096072, -0.105329, -0.100771, -0.087584, -0.079320, -0.075489, -0.072081, -0.064183, -0.054662, -0.048601, -0.049465, -0.047050, -0.045011, -0.040009, -0.032508, -0.025212, -0.018144, -0.011996, -0.008136, -0.003187, -0.003214, -0.006646, -0.013044, -0.019446, -0.020615, -0.022270, -0.021298, -0.020215, -0.020946, -0.026034, -0.026598, -0.021025, -0.012328
	-0.057184, -0.064908, -0.073093, -0.081584, -0.091971, -0.097048, -0.097688, -0.101869, -0.106651, -0.102162, -0.095658, -0.087938, -0.082718, -0.077017, -0.069608, -0.060682, -0.056889, -0.056864, -0.054260, -0.052011, -0.044563, -0.038927, -0.031943, -0.025832, -0.021170, -0.014319, -0.009046, -0.008543, -0.011751, -0.020287, -0.026608, -0.027259, -0.029120, -0.025549, -0.023221, -0.027725, -0.032477, -0.028427, -0.019343, -0.014932
	-0.060411, -0.062241, -0.080781, -0.090744, -0.100903, -0.099702, -0.098468, -0.104236, -0.116853, -0.112701, -0.102623, -0.095036, -0.091407, -0.089871, -0.079701, -0.070222, -0.064325, -0.063875, -0.062248, -0.059396, -0.052699, -0.047589, -0.041526, -0.028442, -0.024526, -0.019549, -0.015403, -0.014251, -0.017989, -0.022824, -0.027328, -0.029155, -0.033315, -0.032426, -0.027619, -0.030776, -0.033688, -0.032458, -0.027219, -0.019649
	-0.067541, -0.076514, -0.082321, -0.088656, -0.099968, -0.104930, -0.105875, -0.109051, -0.115531, -0.112996, -0.105760, -0.100390, -0.096171, -0.090011, -0.080050, -0.073632, -0.067451, -0.067031, -0.065225, -0.062471, -0.056370, -0.050129, -0.041626, -0.030801, -0.027579, -0.022472, -0.014826, -0.015306, -0.020316, -0.025953, -0.030661, -0.034103, -0.035502, -0.032738, -0.031311, -0.037314, -0.041306, -0.035280, -0.027449, -0.020395
	-0.068162, -0.069269, -0.088235, -0.096809, -0.103385, -0.103271, -0.102507, -0.109535, -0.123412, -0.118580, -0.106622, -0.099580, -0.097644, -0.096978, -0.087259, -0.077196, -0.068978, -0.067016, -0.063682, -0.062548, -0.057901, -0.052295, -0.044088, -0.032703, -0.026551, -0.021607, -0.014155, -0.013747, -0.017390, -0.022419, -0.027444, -0.030877, -0.033450, -0.032423, -0.032041, -0.033598, -0.035149, -0.034054, -0.029356, -0.020998
	-0.069473, -0.075924, -0.083569, -0.089648, -0.101235, -0.105828, -0.109144, -0.112613, -0.117233, -0.114186, -0.107090, -0.098616, -0.097084, -0.094257, -0.086773, -0.076409, -0.069532, -0.066472, -0.060956, -0.059191, -0.052886, -0.047752, -0.041275, -0.032437, -0.027780, -0.020398, -0.012061, -0.010133, -0.014056, -0.021528, -0.027924, -0.030605, -0.030609, -0.026068, -0.029346, -0.033991, -0.038254, -0.030610, -0.021109, -0.015885
	-0.068084, -0.066409, -0.083944, -0.094013, -0.102504, -0.105274, -0.106036, -0.112090, -0.121664, -0.117824, -0.104850, -0.097467, -0.098833, -0.098622, -0.089603, -0.078147, -0.068143, -0.066300, -0.061573, -0.057727, -0.054825, -0.048625, -0.040164, -0.030532, -0.025948, -0.020264, -0.014196, -0.010702, -0.013794, -0.019775, -0.026095, -0.028838, -0.030254, -0.027944, -0.027980, -0.030915, -0.032446, -0.028861, -0.023732, -0.014676
	-0.065280, -0.068669, -0.076948, -0.082397, -0.094986, -0.105117, -0.107099, -0.108954, -0.112557, -0.110326, -0.100725, -0.096325, -0.096240, -0.092388, -0.081185, -0.071682, -0.065650, -0.062250, -0.057027, -0.054691, -0.048349, -0.042069, -0.032712, -0.027728, -0.023396, -0.018458, -0.008357, -0.005699, -0.011447, -0.020033, -0.026387, -0.030280, -0.028443, -0.023735, -0.023838, -0.031580, -0.034204, -0.027768, -0.018029, -0.010628
	-0.061662, -0.057052, -0.075163, -0.086710, -0.094182, -0.097544, -0.098814, -0.105908, -0.114460, -0.111718, -0.097559, -0.091614, -0.093860, -0.093098, -0.081687, -0.069410, -0.064117, -0.062745, -0.055603, -0.051413, -0.048043, -0.040363, -0.031842, -0.023420, -0.017470, -0.012600, -0.008163, -0.003898, -0.007635, -0.013254, -0.019807, -0.025153, -0.027074, -0.023513, -0.023727, -0.028669, -0.029153, -0.024831, -0.018735, -0.009246
	-0.056176, -0.059439, -0.066501, -0.071527, -0.085216, -0.094918, -0.097595, -0.099419, -0.101847, -0.102015, -0.093849, -0.089867, -0.088840, -0.083167, -0.071832, -0.062522, -0.058023, -0.057771, -0.053050, -0.048285, -0.041374, -0.033527, -0.024473, -0.018428, -0.013958, -0.008161, -0.001196, 0.001754, -0.004016, -0.011132, -0.018325, -0.021813, -0.021514, -0.016948, -0.018061, -0.025702, -0.028671, -0.021470, -0.011028, -0.001934
	-0.059202, -0.050525, -0.065461, -0.076792, -0.084156, -0.088538, -0.090719, -0.096070, -0.105729, -0.105136, -0.090350, -0.083865, -0.087807, -0.086145, -0.074773, -0.064235, -0.057641, -0.055896, -0.051286, -0.046566, -0.042431, -0.034723, -0.023762, -0.014983, -0.009126, -0.004877, 0.000094, 0.003492, -0.000931, -0.005883, -0.011665, -0.015251, -0.016432, -0.016119, -0.015373, -0.018827, -0.019994, -0.017564, -0.012298, 0.002094
	-0.055561, -0.058184, -0.062669, -0.068111, -0.080741, -0.091895, -0.093911, -0.094387, -0.100239, -0.100695, -0.089841, -0.085682, -0.085212, -0.082910, -0.073072, -0.063594, -0.056157, -0.053482, -0.048107, -0.045405, -0.039982, -0.029777, -0.019905, -0.013872, -0.009732, -0.004272, 0.003500, 0.006909, 0.001302, -0.004626, -0.012374, -0.014751, -0.014637, -0.011794, -0.012913, -0.018244, -0.023377, -0.018086, -0.006575, 0.003294
	-0.062834, -0.047300, -0.060870, -0.073023, -0.079303, -0.082121, -0.083623, -0.091321, -0.100996, -0.098896, -0.085406, -0.078881, -0.081932, -0.082077, -0.074409, -0.063158, -0.053822, -0.050328, -0.045077, -0.039678, -0.035825, -0.028532, -0.017793, -0.009121, -0.003444, -0.000905, 0.003990, 0.007745, 0.004595, 0.000143, -0.004555, -0.007411, -0.010850, -0.010100, -0.010079, -0.013177, -0.016434, -0.014663, -0.010248, -0.000213
	-0.054748, -0.053907, -0.057576, -0.063118, -0.072478, -0.081366, -0.084424, -0.086348, -0.089718, -0.089305, -0.081771, -0.076889, -0.076923, -0.073518, -0.067973, -0.057643, -0.050848, -0.046966, -0.041560, -0.036436, -0.029233, -0.020685, -0.010240, -0.004935, -0.001084, 0.002478, 0.009168, 0.014038, 0.010885, 0.004752, -0.001650, -0.004209, -0.003998, -0.002336, -0.003784, -0.010930, -0.016480, -0.012798, -0.003650, 0.002998
	-0.059345, -0.041989, -0.057435, -0.068229, -0.072857, -0.072586, -0.075155, -0.083286, -0.091292, -0.089727, -0.073702, -0.068353, -0.072910, -0.073863, -0.065527, -0.053635, -0.046064, -0.043899, -0.037607, -0.031251, -0.026194, -0.018885, -0.008095, 0.000309, 0.004911, 0.007046, 0.010642, 0.015635, 0.015277, 0.012612, 0.008074, 0.004852, 0.001546, 0.000504, 0.000589, -0.002769, -0.006432, -0.007765, -0.005391, 0.006950
	-0.050324, -0.049088, -0.052417, -0.057257, -0.063818, -0.071057, -0.074636, -0.075459, -0.079445, -0.077368, -0.068788, -0.063940, -0.065040, -0.063419, -0.054864, -0.044910, -0.038774, -0.036951, -0.031149, -0.026080, -0.018383, -0.011985, -0.001732, 0.003893, 0.007180, 0.011120, 0.017429, 0.021738, 0.019167, 0.015812, 0.011027, 0.007243, 0.006720, 0.009346, 0.006598, -0.003776, -0.009199, -0.007592, 0.005481, 0.014396
	-0.058437, -0.035937, -0.050762, -0.060425, -0.061123, -0.059090, -0.062399, -0.072124, -0.080338, -0.074950, -0.060985, -0.054754, -0.059333, -0.060500, -0.051714, -0.038834, -0.031117, -0.031693, -0.025186, -0.017982, -0.014316, -0.010137, 0.000228, 0.008774, 0.014018, 0.016470, 0.019918, 0.022071, 0.021109, 0.019957, 0.018698, 0.015803, 0.013135, 0.011136, 0.008719, 0.003522, -0.000994, 0.000525, 0.006297, 0.018454
	-0.046143, -0.041577, -0.045391, -0.046668, -0.051722, -0.057607, -0.062802, -0.065205, -0.068243, -0.066293, -0.058216, -0.051324, -0.051806, -0.051018, -0.043393, -0.032431, -0.024016, -0.023321, -0.018504, -0.013897, -0.008455, -0.001123, 0.006609, 0.010462, 0.013887, 0.019328, 0.024804, 0.026590, 0.023420, 0.020337, 0.017129, 0.017199, 0.016391, 0.015616, 0.013257, 0.005832, -0.000019, 0.003462, 0.014308, 0.023624
	-0.051989, -0.030294, -0.043380, -0.051339, -0.050711, -0.048193, -0.052258, -0.061218, -0.070507, -0.068810, -0.049476, -0.042352, -0.046018, -0.046673, -0.038670, -0.027263, -0.018137, -0.018587, -0.013603, -0.008482, -0.004647, -0.000011, 0.008230, 0.015652, 0.019436, 0.023069, 0.024762, 0.027750, 0.028115, 0.026227, 0.022220, 0.023166, 0.020341, 0.018455, 0.014918, 0.011932, 0.007138, 0.008523, 0.014718, 0.026201
	-0.041448, -0.035286, -0.036538, -0.037577, -0.044652, -0.049300, -0.051092, -0.052841, -0.058068, -0.056947, -0.046235, -0.038436, -0.037494, -0.034175, -0.028932, -0.016904, -0.010075, -0.010552, -0.004464, -0.001243, 0.003236, 0.010200, 0.015604, 0.020362, 0.023157, 0.028023, 0.032826, 0.035958, 0.034819, 0.030600, 0.025988, 0.026013, 0.026284, 0.025661, 0.022322, 0.013336, 0.006464, 0.011312, 0.022330, 0.031668
	-0.048540, -0.022534, -0.035260, -0.042156, -0.042749, -0.037408, -0.038818, -0.047322, -0.056808, -0.053643, -0.035691, -0.027822, -0.028789, -0.028255, -0.020274, -0.007285, -0.000723, -0.000788, 0.005440, 0.008938, 0.008953, 0.012074, 0.017957, 0.025241, 0.029175, 0.032057, 0.033733, 0.038359, 0.039349, 0.037161, 0.034052, 0.034585, 0.032020, 0.029940, 0.026326, 0.024577, 0.020432, 0.021586, 0.024568, 0.034552
	-0.033086, -0.027982, -0.029443, -0.029011, -0.035629, -0.040579, -0.038290, -0.037389, -0.041260, -0.040430, -0.032279, -0.021394, -0.018817, -0.015525, -0.007558, 0.006345, 0.011048, 0.011271, 0.013497, 0.017030, 0.017449, 0.022752, 0.026764, 0.030722, 0.033532, 0.037203, 0.043356, 0.048536, 0.047776, 0.043851, 0.039311, 0.039944, 0.039954, 0.038931, 0.034893, 0.030946, 0.023127, 0.027359, 0.034859, 0.043920
	-0.036218, -0.016846, -0.030897, -0.036980, -0.037261, -0.033334, -0.030888, -0.034074, -0.042142, -0.039980, -0.021377, -0.013603, -0.014171, -0.013131, -0.001768, 0.014998, 0.020060, 0.018173, 0.019934, 0.024704, 0.023739, 0.024617, 0.027288, 0.035116, 0.041187, 0.043128, 0.045921, 0.051709, 0.053031, 0.050698, 0.047697, 0.047728, 0.046845, 0.043201, 0.041805, 0.040728, 0.036184, 0.034435, 0.035120, 0.045329
	-0.029808, -0.023871, -0.026541, -0.026705, -0.031203, -0.036908, -0.034411, -0.029231, -0.028090, -0.026102, -0.016691, -0.007747, -0.004471, 0.001560, 0.010738, 0.025062, 0.027672, 0.024833, 0.026976, 0.029502, 0.030754, 0.035709, 0.039403, 0.044719, 0.046379, 0.049250, 0.054178, 0.059793, 0.059542, 0.052111, 0.047608, 0.050103, 0.053142, 0.052747, 0.050045, 0.044102, 0.033149, 0.035392, 0.045678, 0.054080
	-0.032238, -0.008993, -0.023999, -0.030969, -0.028658, -0.024887, -0.024493, -0.028088, -0.031053, -0.022849, -0.003868, 0.004647, 0.004540, 0.007560, 0.018373, 0.031401, 0.035778, 0.033768, 0.035173, 0.035884, 0.036597, 0.038940, 0.044566, 0.053914, 0.056554, 0.056382, 0.056449, 0.060387, 0.062696, 0.058223, 0.055016, 0.056193, 0.056891, 0.052793, 0.052741, 0.052626, 0.048117, 0.045032, 0.048033, 0.055100
	-0.019758, -0.015110, -0.017814, -0.018871, -0.023340, -0.028653, -0.026880, -0.018681, -0.017020, -0.011343, -0.001002, 0.008249, 0.014012, 0.020367, 0.026878, 0.038534, 0.041827, 0.039532, 0.039775, 0.039109, 0.043172, 0.049325, 0.056604, 0.059583, 0.059329, 0.059876, 0.062766, 0.068759, 0.067214, 0.059657, 0.055950, 0.056798, 0.058619, 0.058591, 0.059849, 0.056473, 0.046841, 0.047921, 0.058342, 0.065346
	-0.018628, -0.000296, -0.014764, -0.022634, -0.020483, -0.016362, -0.015485, -0.017352, -0.020246, -0.010362, 0.008635, 0.018414, 0.018542, 0.024258, 0.033370, 0.045728, 0.049983, 0.044610, 0.044638, 0.047649, 0.049220, 0.051954, 0.058932, 0.065915, 0.069102, 0.067410, 0.067680, 0.073734, 0.072203, 0.067293, 0.063945, 0.064378, 0.065047, 0.061989, 0.062882, 0.063468, 0.059707, 0.057986, 0.059739, 0.066139
	-0.010091, -0.006551, -0.008018, -0.009589, -0.016068, -0.020662, -0.019451, -0.010985, -0.009391, -0.003580, 0.007826, 0.019598, 0.024961, 0.033762, 0.040618, 0.050868, 0.052139, 0.050495, 0.049198, 0.051777, 0.056840, 0.061771, 0.068414, 0.072295, 0.073443, 0.072145, 0.073414, 0.079338, 0.075988, 0.067367, 0.064745, 0.064435, 0.066982, 0.065811, 0.067424, 0.063230, 0.058438, 0.059982, 0.067672, 0.072460
	-0.016254, 0.006291, -0.008031, -0.013944, -0.014475, -0.010741, -0.009932, -0.011709, -0.015503, -0.006971, 0.013190, 0.024865, 0.029121, 0.033942, 0.044335, 0.054572, 0.058078, 0.055224, 0.055897, 0.058327, 0.061207, 0.063939, 0.070506, 0.078141, 0.084203, 0.081223, 0.079519, 0.082883, 0.080890, 0.076174, 0.071279, 0.073064, 0.071225, 0.066859, 0.069860, 0.070836, 0.069427, 0.069140, 0.070950, 0.075269
	-0.008127, 0.000730, 0.001164, -0.000308, -0.006659, -0.012343, -0.011463, -0.003755, -0.001876, 0.005166, 0.016616, 0.030243, 0.036509, 0.045020, 0.053681, 0.063738, 0.066425, 0.063964, 0.062796, 0.065633, 0.071912, 0.077280, 0.082580, 0.086477, 0.089798, 0.089603, 0.091453, 0.096125, 0.088708, 0.079903, 0.074317, 0.076190, 0.075399, 0.075242, 0.079628, 0.077855, 0.071473, 0.073702, 0.082757, 0.088086
	-0.010951, 0.013218, -0.000878, -0.006241, -0.005623, 0.000046, 0.000158, -0.002943, -0.005314, 0.005491, 0.026890, 0.035754, 0.041490, 0.045829, 0.059325, 0.070249, 0.074114, 0.071815, 0.073229, 0.076313, 0.080778, 0.081554, 0.087919, 0.096206, 0.101562, 0.101674, 0.100494, 0.103989, 0.100292, 0.093977, 0.088080, 0.088136, 0.086555, 0.081494, 0.084966, 0.087073, 0.084113, 0.085184, 0.087700, 0.092188
	-0.002972, 0.006020, 0.006098, 0.004303, 0.001326, -0.002386, -0.001840, 0.005325, 0.008624, 0.016246, 0.026781, 0.039696, 0.048540, 0.055938, 0.066982, 0.076497, 0.080828, 0.079669, 0.080127, 0.083754, 0.089783, 0.093456, 0.100570, 0.105322, 0.107132, 0.110571, 0.113141, 0.118064, 0.111721, 0.101634, 0.093555, 0.093112, 0.093104, 0.092325, 0.094780, 0.092552, 0.085283, 0.088882, 0.097508, 0.105280
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 11.4
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Preperations]
version = 1
points = 
	0.012158, -0.006098, -0.020628, -0.034069, -0.049418, -0.058491, -0.062706, -0.063181, -0.065552, -0.063461, -0.057373, -0.056717, -0.056579, -0.054080, -0.053373, -0.056878, -0.057281, -0.055224, -0.049676, -0.047605, -0.041454, -0.034605, -0.022490, -0.011292, -0.009411, -0.005344, -0.003510, -0.002717, -0.005999, -0.010712, -0.013141, -0.015611, -0.020004, -0.017667, -0.016629, -0.022248, -0.024864, -0.024065, -0.014921, -0.010826
	-0.005958, -0.021084, -0.033800, -0.047903, -0.059950, -0.071345, -0.072502, -0.073350, -0.075852, -0.072963, -0.067236, -0.064315, -0.065698, -0.064338, -0.062871, -0.065238, -0.067095, -0.063584, -0.059241, -0.057846, -0.051380, -0.043157, -0.030230, -0.019950, -0.018121, -0.014291, -0.009354, -0.013065, -0.016464, -0.022925, -0.025337, -0.026541, -0.030577, -0.029068, -0.027094, -0.030532, -0.034241, -0.032625, -0.021498, -0.020513
	-0.017526, -0.027763, -0.040710, -0.055305, -0.068172, -0.079641, -0.081247, -0.081903, -0.083679, -0.081855, -0.073270, -0.070340, -0.072083, -0.071536, -0.066055, -0.065901, -0.069085, -0.066531, -0.063284, -0.061616, -0.053366, -0.047292, -0.035451, -0.023167, -0.022205, -0.016699, -0.012552, -0.014153, -0.018802, -0.030443, -0.032210, -0.034051, -0.034437, -0.031439, -0.030406, -0.032817, -0.036351, -0.034849, -0.024250, -0.019489
	-0.017750, -0.030284, -0.043463, -0.055839, -0.071865, -0.084888, -0.086157, -0.084619, -0.086681, -0.084515, -0.075246, -0.073263, -0.075604, -0.075123, -0.069177, -0.070723, -0.071097, -0.068644, -0.065465, -0.063718, -0.057574, -0.049335, -0.036556, -0.028418, -0.028259, -0.023387, -0.018454, -0.020519, -0.027499, -0.038314, -0.041534, -0.041886, -0.039972, -0.036438, -0.033959, -0.033009, -0.038291, -0.036339, -0.022688, -0.024783
	-0.021354, -0.034103, -0.047541, -0.060551, -0.075691, -0.089373, -0.092241, -0.091621, -0.093203, -0.090723, -0.082480, -0.079781, -0.079706, -0.079674, -0.074365, -0.073780, -0.073465, -0.070165, -0.064970, -0.065503, -0.059104, -0.051038, -0.041817, -0.031243, -0.031386, -0.028837, -0.023658, -0.024237, -0.029641, -0.039210, -0.042766, -0.044461, -0.041863, -0.039075, -0.034881, -0.034571, -0.039386, -0.038253, -0.031659, -0.024202
	-0.027696, -0.041184, -0.054054, -0.064759, -0.080898, -0.094964, -0.097906, -0.098033, -0.101256, -0.098300, -0.091517, -0.088420, -0.086945, -0.085220, -0.079938, -0.079979, -0.079828, -0.074842, -0.072903, -0.072415, -0.065384, -0.057454, -0.048482, -0.040977, -0.039336, -0.036065, -0.032553, -0.034336, -0.039337, -0.046271, -0.049398, -0.051220, -0.049530, -0.045000, -0.045029, -0.042100, -0.049767, -0.046386, -0.035574, -0.032188
	-0.033426, -0.046259, -0.059363, -0.068024, -0.084858, -0.097009, -0.103434, -0.106215, -0.107319, -0.106178, -0.100333, -0.097536, -0.095352, -0.091322, -0.086332, -0.082309, -0.081440, -0.078413, -0.075067, -0.073134, -0.068255, -0.062667, -0.054300, -0.046004, -0.042001, -0.039181, -0.035010, -0.036092, -0.041599, -0.048788, -0.051751, -0.051179, -0.051019, -0.049121, -0.045860, -0.046756, -0.050005, -0.051613, -0.040237, -0.035349
	-0.037931, -0.051993, -0.066455, -0.075044, -0.088177, -0.102890, -0.108223, -0.112373, -0.115787, -0.113421, -0.108543, -0.105936, -0.101048, -0.096863, -0.090726, -0.087882, -0.086665, -0.083874, -0.081096, -0.080894, -0.075125, -0.071038, -0.063072, -0.054696, -0.051039, -0.046728, -0.042566, -0.043887, -0.048745, -0.056834, -0.059808, -0.060521, -0.060664, -0.057968, -0.056317, -0.052477, -0.058814, -0.055877, -0.046325, -0.042545
	-0.041429, -0.053634, -0.067633, -0.077111, -0.090998, -0.103561, -0.109445, -0.114741, -0.120075, -0.119821, -0.114703, -0.110411, -0.105589, -0.099826, -0.093730, -0.089705, -0.087199, -0.086439, -0.082688, -0.082221, -0.078348, -0.073203, -0.065273, -0.058731, -0.054025, -0.049231, -0.044830, -0.043830, -0.045839, -0.054137, -0.059075, -0.059515, -0.058546, -0.056956, -0.054145, -0.053129, -0.056587, -0.056341, -0.047057, -0.039936
	-0.044295, -0.058972, -0.072101, -0.082726, -0.095001, -0.106449, -0.111505, -0.118363, -0.124608, -0.123506, -0.120263, -0.115400, -0.110227, -0.104535, -0.100348, -0.095757, -0.092961, -0.092377, -0.089613, -0.088047, -0.084834, -0.079314, -0.072500, -0.064519, -0.060449, -0.055767, -0.051803, -0.050997, -0.052855, -0.058115, -0.063348, -0.065363, -0.067936, -0.063474, -0.061475, -0.054726, -0.062529, -0.055352, -0.048878, -0.044991
	-0.045804, -0.056574, -0.073308, -0.082450, -0.097495, -0.107467, -0.111501, -0.116418, -0.126724, -0.125980, -0.123231, -0.120494, -0.114667, -0.111289, -0.103451, -0.099228, -0.095880, -0.095882, -0.093328, -0.091000, -0.087051, -0.081909, -0.075949, -0.064971, -0.061050, -0.055137, -0.049046, -0.047319, -0.049806, -0.056968, -0.059608, -0.060249, -0.063032, -0.060556, -0.056284, -0.056263, -0.058891, -0.057890, -0.051554, -0.042382
	-0.049818, -0.062681, -0.076305, -0.084328, -0.098717, -0.107866, -0.113937, -0.120088, -0.128622, -0.128931, -0.126353, -0.123191, -0.118529, -0.115642, -0.106288, -0.103976, -0.099708, -0.097750, -0.094501, -0.094545, -0.090910, -0.085952, -0.077352, -0.067196, -0.062435, -0.057738, -0.052934, -0.051098, -0.055294, -0.061112, -0.063120, -0.067525, -0.067979, -0.066558, -0.064608, -0.060597, -0.067812, -0.057641, -0.056224, -0.046471
	-0.050591, -0.060432, -0.075602, -0.083877, -0.096933, -0.106147, -0.112334, -0.118295, -0.127966, -0.128757, -0.125157, -0.121831, -0.118557, -0.116124, -0.108723, -0.104502, -0.099469, -0.095841, -0.090662, -0.089822, -0.087969, -0.084545, -0.076375, -0.064821, -0.059093, -0.053427, -0.047372, -0.044341, -0.047964, -0.054064, -0.057133, -0.059152, -0.061568, -0.059109, -0.056640, -0.056691, -0.056844, -0.054564, -0.048514, -0.040641
	-0.047704, -0.059564, -0.073127, -0.080945, -0.093764, -0.105483, -0.111501, -0.118792, -0.124812, -0.126576, -0.122064, -0.118087, -0.116126, -0.114867, -0.108053, -0.103336, -0.097558, -0.093250, -0.086537, -0.085303, -0.083677, -0.079292, -0.070542, -0.062526, -0.056818, -0.052534, -0.044035, -0.041353, -0.046942, -0.051329, -0.055481, -0.062777, -0.058499, -0.058025, -0.057390, -0.053562, -0.060843, -0.046555, -0.046260, -0.036083
	-0.046496, -0.052983, -0.067518, -0.076904, -0.091704, -0.103105, -0.111995, -0.117751, -0.122307, -0.122941, -0.118230, -0.115004, -0.114258, -0.113138, -0.105515, -0.098417, -0.093384, -0.090070, -0.083281, -0.079846, -0.078725, -0.075452, -0.066225, -0.057269, -0.053103, -0.047808, -0.039772, -0.036834, -0.041270, -0.047376, -0.051111, -0.053848, -0.053029, -0.050301, -0.048919, -0.050775, -0.050121, -0.046842, -0.039633, -0.030497
	-0.040695, -0.051685, -0.064038, -0.070974, -0.086679, -0.101773, -0.109889, -0.114373, -0.117883, -0.118764, -0.113125, -0.110931, -0.111099, -0.109664, -0.098733, -0.093182, -0.090154, -0.086213, -0.077214, -0.077108, -0.075555, -0.069117, -0.060704, -0.054093, -0.049253, -0.044799, -0.037536, -0.035304, -0.040134, -0.045456, -0.051720, -0.056675, -0.053743, -0.052923, -0.049701, -0.050238, -0.056776, -0.041485, -0.041755, -0.027329
	-0.039842, -0.039428, -0.055732, -0.063890, -0.079179, -0.092823, -0.101698, -0.106156, -0.111709, -0.113152, -0.108033, -0.104872, -0.105645, -0.103501, -0.094487, -0.087264, -0.084273, -0.080950, -0.074116, -0.070973, -0.068409, -0.062825, -0.054757, -0.044150, -0.040620, -0.036602, -0.031538, -0.026478, -0.031123, -0.037600, -0.042341, -0.046700, -0.047380, -0.042880, -0.040967, -0.045367, -0.044192, -0.038553, -0.029948, -0.020790
	-0.030596, -0.038279, -0.051528, -0.058981, -0.073983, -0.089044, -0.099173, -0.101740, -0.104830, -0.107083, -0.102306, -0.101554, -0.101336, -0.097146, -0.089217, -0.083800, -0.080621, -0.078071, -0.071535, -0.068328, -0.065806, -0.056882, -0.048683, -0.039756, -0.036349, -0.031328, -0.025351, -0.024133, -0.029773, -0.033858, -0.040011, -0.044146, -0.043900, -0.044797, -0.038019, -0.042319, -0.047297, -0.031851, -0.034318, -0.013527
	-0.032121, -0.034722, -0.047839, -0.054710, -0.069175, -0.084213, -0.094533, -0.097233, -0.100863, -0.104775, -0.099781, -0.097416, -0.098804, -0.096059, -0.086694, -0.079692, -0.076749, -0.074609, -0.068106, -0.063906, -0.061136, -0.055447, -0.045559, -0.035389, -0.029696, -0.025708, -0.020034, -0.017335, -0.022665, -0.028532, -0.032369, -0.035760, -0.037212, -0.035201, -0.032872, -0.034132, -0.035907, -0.032127, -0.025026, -0.009282
	-0.026707, -0.034374, -0.045183, -0.052691, -0.067014, -0.084964, -0.092286, -0.094441, -0.099291, -0.103609, -0.098278, -0.094972, -0.097169, -0.095394, -0.086653, -0.080205, -0.076284, -0.070594, -0.064535, -0.062012, -0.060174, -0.051216, -0.040622, -0.033396, -0.029636, -0.024235, -0.017274, -0.018232, -0.021459, -0.024778, -0.031754, -0.034481, -0.033398, -0.037949, -0.030432, -0.033219, -0.038432, -0.021975, -0.030052, -0.009295
	-0.028559, -0.029280, -0.042071, -0.048655, -0.061603, -0.076257, -0.086817, -0.091815, -0.095682, -0.098682, -0.093729, -0.091168, -0.092213, -0.090073, -0.084070, -0.077048, -0.072045, -0.066267, -0.060309, -0.053639, -0.051696, -0.046852, -0.034069, -0.025602, -0.020640, -0.018021, -0.013180, -0.009049, -0.013846, -0.018012, -0.021061, -0.024515, -0.027068, -0.026804, -0.024283, -0.025595, -0.028234, -0.025272, -0.019246, -0.008595
	-0.025711, -0.029003, -0.038836, -0.048015, -0.058511, -0.074480, -0.083738, -0.087945, -0.091439, -0.094310, -0.090288, -0.087858, -0.088589, -0.086163, -0.081829, -0.075146, -0.071136, -0.064399, -0.057338, -0.052103, -0.049650, -0.043210, -0.032998, -0.023124, -0.020191, -0.016625, -0.012433, -0.010465, -0.009871, -0.015007, -0.021217, -0.021582, -0.023800, -0.027652, -0.021527, -0.027137, -0.030828, -0.020152, -0.026202, -0.008568
	-0.031287, -0.022523, -0.035800, -0.041583, -0.052691, -0.065901, -0.075941, -0.079246, -0.083936, -0.086778, -0.082235, -0.078893, -0.080642, -0.079419, -0.074324, -0.067418, -0.062113, -0.057744, -0.049923, -0.043390, -0.040055, -0.035512, -0.023838, -0.015485, -0.009895, -0.008346, -0.005387, 0.001467, -0.000104, -0.003777, -0.007926, -0.012023, -0.013970, -0.014207, -0.013994, -0.017009, -0.019233, -0.019282, -0.014210, -0.001146
	-0.020719, -0.024043, -0.035160, -0.041635, -0.051902, -0.063884, -0.072884, -0.076738, -0.081856, -0.083761, -0.077857, -0.074651, -0.077952, -0.076310, -0.069721, -0.063240, -0.056775, -0.055188, -0.046711, -0.042996, -0.039499, -0.032268, -0.023129, -0.015735, -0.012305, -0.009383, -0.005789, -0.001996, -0.001166, -0.005106, -0.009634, -0.009864, -0.011905, -0.015913, -0.010246, -0.016645, -0.022975, -0.011972, -0.018524, 0.001048
	-0.026050, -0.019774, -0.032555, -0.037813, -0.044657, -0.054435, -0.065271, -0.071019, -0.075585, -0.077479, -0.072635, -0.069526, -0.071046, -0.070770, -0.063085, -0.055960, -0.050956, -0.049593, -0.042773, -0.034996, -0.032645, -0.029030, -0.020343, -0.011008, -0.005751, -0.003252, 0.000746, 0.003215, 0.001749, -0.000068, -0.001413, -0.002608, -0.005837, -0.007103, -0.008431, -0.012027, -0.015656, -0.014417, -0.006321, 0.003748
	-0.021728, -0.019178, -0.031232, -0.036249, -0.042206, -0.053190, -0.064017, -0.068545, -0.074597, -0.074544, -0.069543, -0.065779, -0.067928, -0.067354, -0.060655, -0.052790, -0.047723, -0.046044, -0.038188, -0.034539, -0.032080, -0.027152, -0.018902, -0.012508, -0.009304, -0.003955, -0.000288, -0.001549, -0.000556, -0.003756, -0.008467, -0.003851, -0.005999, -0.012959, -0.007423, -0.015332, -0.017388, -0.005695, -0.010807, 0.007710
	-0.028204, -0.017096, -0.027984, -0.032129, -0.038374, -0.046561, -0.059356, -0.061847, -0.069228, -0.070551, -0.065474, -0.059719, -0.059893, -0.060271, -0.053666, -0.047202, -0.041189, -0.039979, -0.033189, -0.028761, -0.025714, -0.021660, -0.014905, -0.007841, -0.004669, -0.001174, 0.001874, 0.005613, 0.005527, 0.001504, -0.000694, 0.001892, 0.001885, -0.002506, -0.005619, -0.007166, -0.009935, -0.007406, 0.000545, 0.009983
	-0.019393, -0.017785, -0.025482, -0.028146, -0.036861, -0.047528, -0.055696, -0.059118, -0.064151, -0.066346, -0.060565, -0.055661, -0.055495, -0.051944, -0.048147, -0.040645, -0.036359, -0.035990, -0.026764, -0.024843, -0.023572, -0.019648, -0.013807, -0.006811, -0.004589, -0.000266, 0.003010, 0.004931, 0.006834, 0.003254, -0.001690, 0.003120, 0.001036, -0.005283, 0.000659, -0.007399, -0.010996, -0.000832, -0.006381, 0.012135
	-0.021519, -0.010062, -0.018662, -0.023011, -0.029067, -0.036961, -0.043194, -0.048197, -0.053632, -0.055489, -0.050054, -0.045247, -0.042655, -0.040243, -0.034315, -0.027094, -0.022697, -0.021644, -0.015333, -0.010768, -0.013712, -0.012051, -0.005326, 0.000560, 0.005300, 0.007429, 0.009930, 0.015968, 0.016454, 0.012383, 0.010385, 0.011612, 0.011413, 0.008357, 0.006831, 0.005524, 0.003087, 0.003507, 0.009876, 0.018892
	-0.017331, -0.015238, -0.021971, -0.024651, -0.029507, -0.040209, -0.044232, -0.046101, -0.052689, -0.053151, -0.047133, -0.042985, -0.040475, -0.037020, -0.029999, -0.021348, -0.018232, -0.017876, -0.013058, -0.008535, -0.013279, -0.011527, -0.006296, -0.001615, 0.002270, 0.006991, 0.010272, 0.013407, 0.015950, 0.012503, 0.008026, 0.013701, 0.011513, 0.004867, 0.010667, 0.006774, 0.003571, 0.012416, 0.004875, 0.020961
	-0.022637, -0.011107, -0.018340, -0.023896, -0.028320, -0.038092, -0.041212, -0.041642, -0.044537, -0.046015, -0.041699, -0.035805, -0.033527, -0.030911, -0.022925, -0.010175, -0.007279, -0.008644, -0.005065, -0.000597, -0.003797, -0.004052, 0.000635, 0.006175, 0.010857, 0.012993, 0.016956, 0.022765, 0.023298, 0.020262, 0.018285, 0.019467, 0.021161, 0.018785, 0.017891, 0.017817, 0.013874, 0.012825, 0.015904, 0.025844
	-0.014532, -0.010189, -0.019385, -0.022584, -0.028159, -0.037803, -0.040566, -0.038125, -0.040339, -0.038899, -0.033171, -0.028143, -0.025641, -0.019755, -0.012463, -0.003824, -0.000871, -0.002698, -0.000197, 0.001952, -0.001353, -0.000188, 0.004902, 0.012600, 0.014373, 0.016449, 0.018872, 0.022822, 0.026385, 0.020681, 0.015275, 0.021387, 0.023535, 0.016733, 0.022161, 0.018819, 0.011276, 0.020785, 0.014683, 0.032409
	-0.016972, -0.004835, -0.015539, -0.019706, -0.022971, -0.032222, -0.037732, -0.035551, -0.033892, -0.031679, -0.024624, -0.019946, -0.016412, -0.010040, -0.003445, 0.005991, 0.008364, 0.006410, 0.008289, 0.009260, 0.007409, 0.008691, 0.015230, 0.022729, 0.025465, 0.025502, 0.026102, 0.030309, 0.031861, 0.026963, 0.024651, 0.027000, 0.029039, 0.025577, 0.027217, 0.027660, 0.023245, 0.021705, 0.026383, 0.034120
	-0.007042, -0.003943, -0.013314, -0.016082, -0.020497, -0.030911, -0.035096, -0.030889, -0.029351, -0.025337, -0.018980, -0.012449, -0.008879, -0.001902, 0.003577, 0.011256, 0.012460, 0.010502, 0.011904, 0.011483, 0.010067, 0.013356, 0.020792, 0.027368, 0.026382, 0.028554, 0.028164, 0.029993, 0.033232, 0.028830, 0.022354, 0.027991, 0.029607, 0.020011, 0.031066, 0.031755, 0.025061, 0.037228, 0.024607, 0.041453
	-0.012463, -0.000987, -0.008994, -0.014815, -0.017487, -0.026372, -0.031392, -0.028459, -0.025402, -0.024153, -0.015566, -0.007862, -0.004579, 0.001484, 0.010757, 0.017401, 0.019536, 0.016264, 0.016278, 0.018231, 0.018193, 0.018217, 0.025442, 0.034794, 0.036179, 0.034770, 0.033985, 0.040104, 0.040404, 0.034161, 0.030977, 0.032380, 0.034144, 0.031909, 0.033231, 0.035957, 0.034171, 0.033050, 0.038776, 0.042972
	-0.002758, 0.000700, -0.008467, -0.011525, -0.018705, -0.027522, -0.031609, -0.027494, -0.026315, -0.023221, -0.014164, -0.006562, -0.002205, 0.006453, 0.013689, 0.018647, 0.017673, 0.016751, 0.017380, 0.018782, 0.019038, 0.021992, 0.027475, 0.034748, 0.036870, 0.036635, 0.035394, 0.037519, 0.038008, 0.032063, 0.025834, 0.030409, 0.033142, 0.023991, 0.034882, 0.034323, 0.030317, 0.042711, 0.030793, 0.045129
	-0.011501, 0.004979, -0.003199, -0.009532, -0.013737, -0.022490, -0.028056, -0.025047, -0.023987, -0.021727, -0.011113, -0.003633, 0.003070, 0.010580, 0.020230, 0.025058, 0.026653, 0.024592, 0.024567, 0.025613, 0.027386, 0.029282, 0.037705, 0.042901, 0.046601, 0.045443, 0.044217, 0.048155, 0.045715, 0.039788, 0.034981, 0.038594, 0.038594, 0.034532, 0.038671, 0.042065, 0.040659, 0.042101, 0.045919, 0.050030
	-0.005239, 0.006624, -0.001837, -0.005350, -0.012024, -0.022230, -0.026144, -0.022704, -0.021559, -0.017450, -0.008515, 0.000433, 0.007392, 0.014546, 0.023538, 0.029043, 0.029892, 0.027280, 0.028785, 0.030662, 0.032758, 0.032649, 0.040035, 0.046372, 0.048654, 0.050330, 0.049538, 0.049746, 0.048851, 0.041068, 0.034598, 0.041375, 0.041379, 0.030621, 0.043091, 0.044712, 0.038634, 0.053475, 0.042814, 0.059369
	-0.011843, 0.005417, 0.000007, -0.005709, -0.011391, -0.019100, -0.024151, -0.021274, -0.019356, -0.016953, -0.004422, 0.002891, 0.010688, 0.018353, 0.027665, 0.035281, 0.036655, 0.034937, 0.036795, 0.039994, 0.042705, 0.042668, 0.048600, 0.055673, 0.059602, 0.061002, 0.059934, 0.064283, 0.061835, 0.052838, 0.048644, 0.048401, 0.048158, 0.044262, 0.049173, 0.053313, 0.050054, 0.051718, 0.058112, 0.062677
	-0.003249, 0.007140, -0.000190, -0.005182, -0.010664, -0.017472, -0.021072, -0.018928, -0.015929, -0.011810, -0.001170, 0.006999, 0.014346, 0.022026, 0.033087, 0.037703, 0.039304, 0.038986, 0.040531, 0.042739, 0.044912, 0.045850, 0.052980, 0.060894, 0.062495, 0.065477, 0.066306, 0.069035, 0.066301, 0.058359, 0.048879, 0.054660, 0.053906, 0.042834, 0.051292, 0.054304, 0.049390, 0.064968, 0.053062, 0.067337
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 80.0
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Peperations]
version = 1
points = 
	0.022498, 0.020830, 0.014175, -0.000111, -0.007965, -0.011932, -0.009252, -0.003320, -0.000118, 0.004151, 0.015991, 0.024593, 0.030148, 0.034696, 0.042241, 0.043592, 0.045307, 0.051419, 0.057700, 0.066468, 0.072764, 0.085492, 0.100446, 0.113063, 0.118900, 0.122870, 0.130290, 0.129755, 0.129462, 0.124089, 0.122420, 0.123461, 0.116841, 0.117893, 0.119241, 0.115227, 0.110631, 0.109920, 0.117187, 0.124332
	0.004953, 0.000716, -0.005511, -0.010742, -0.018400, -0.024021, -0.019665, -0.013525, -0.009878, -0.004126, 0.008939, 0.016408, 0.019292, 0.023840, 0.033007, 0.033600, 0.034448, 0.041047, 0.049029, 0.052882, 0.062512, 0.072410, 0.089182, 0.103027, 0.106205, 0.110789, 0.117912, 0.115269, 0.112784, 0.106051, 0.103603, 0.104209, 0.099603, 0.105100, 0.101466, 0.099610, 0.095780, 0.096420, 0.108661, 0.108286
	-0.007933, -0.002801, -0.011350, -0.022484, -0.029473, -0.033231, -0.030354, -0.021826, -0.018408, -0.013209, 0.001640, 0.008984, 0.012027, 0.014149, 0.024334, 0.028649, 0.030597, 0.034667, 0.041223, 0.046241, 0.051968, 0.062511, 0.079099, 0.090699, 0.097837, 0.101667, 0.108218, 0.106595, 0.104490, 0.095444, 0.089512, 0.089259, 0.089179, 0.091741, 0.094161, 0.094254, 0.091002, 0.088753, 0.095405, 0.102343
	-0.010759, -0.012564, -0.018170, -0.023960, -0.033106, -0.040910, -0.038354, -0.031441, -0.026122, -0.019953, -0.006267, 0.000733, 0.002678, 0.006102, 0.015437, 0.019860, 0.022689, 0.029563, 0.035629, 0.037302, 0.045089, 0.055137, 0.070820, 0.082978, 0.087158, 0.088614, 0.094487, 0.093851, 0.091038, 0.080923, 0.074433, 0.073797, 0.073058, 0.081788, 0.080734, 0.083111, 0.078149, 0.079373, 0.091335, 0.087853
	-0.027313, -0.019238, -0.027920, -0.036645, -0.043223, -0.049872, -0.048503, -0.043853, -0.040737, -0.035179, -0.021622, -0.013493, -0.010171, -0.007317, 0.001347, 0.007440, 0.011360, 0.015985, 0.023916, 0.026329, 0.031680, 0.042865, 0.056754, 0.067621, 0.072919, 0.075964, 0.080156, 0.081233, 0.077771, 0.068443, 0.063939, 0.062251, 0.063828, 0.065094, 0.069498, 0.071735, 0.067423, 0.064065, 0.069162, 0.076272
	-0.033298, -0.035618, -0.039940, -0.043358, -0.050731, -0.061413, -0.060545, -0.055944, -0.052261, -0.045471, -0.035624, -0.027633, -0.021472, -0.017300, -0.006949, -0.002776, -0.000154, 0.006413, 0.012882, 0.014721, 0.023411, 0.031711, 0.040565, 0.054702, 0.058761, 0.061734, 0.065369, 0.066037, 0.061059, 0.053849, 0.049600, 0.048373, 0.049189, 0.054631, 0.050470, 0.056349, 0.047074, 0.049651, 0.057444, 0.057485
	-0.046284, -0.039039, -0.049010, -0.054961, -0.061001, -0.068408, -0.069602, -0.066474, -0.063117, -0.059357, -0.049570, -0.041166, -0.035441, -0.029269, -0.019658, -0.012395, -0.008906, -0.005538, 0.002012, 0.008339, 0.013216, 0.018793, 0.031185, 0.040165, 0.047175, 0.050605, 0.054283, 0.054442, 0.049166, 0.043483, 0.039000, 0.040758, 0.040857, 0.040759, 0.042263, 0.043438, 0.040051, 0.035886, 0.041332, 0.048851
	-0.049893, -0.051919, -0.058103, -0.060142, -0.067656, -0.077159, -0.079195, -0.078019, -0.075421, -0.069471, -0.060409, -0.054194, -0.044226, -0.037275, -0.027912, -0.020020, -0.016789, -0.012491, -0.003457, 0.001129, 0.004540, 0.009435, 0.018232, 0.027941, 0.035138, 0.038227, 0.042656, 0.044103, 0.038517, 0.032121, 0.029666, 0.027319, 0.029774, 0.031572, 0.028887, 0.034828, 0.023795, 0.030023, 0.033606, 0.036047
	-0.061015, -0.055279, -0.067497, -0.072234, -0.078637, -0.083600, -0.085954, -0.087271, -0.088647, -0.083447, -0.073398, -0.065920, -0.058009, -0.048810, -0.040714, -0.032533, -0.027328, -0.020402, -0.011382, -0.006547, -0.005452, -0.002712, 0.004649, 0.014201, 0.021442, 0.025510, 0.032890, 0.034711, 0.030965, 0.026329, 0.018828, 0.019246, 0.018861, 0.019611, 0.020596, 0.021396, 0.020172, 0.015723, 0.020537, 0.029677
	-0.063777, -0.066149, -0.073750, -0.076131, -0.084016, -0.091900, -0.093741, -0.094496, -0.094840, -0.089548, -0.084332, -0.077263, -0.068485, -0.061963, -0.051082, -0.043658, -0.037912, -0.032323, -0.024324, -0.019914, -0.018261, -0.013727, -0.003485, 0.004316, 0.011418, 0.017023, 0.022980, 0.024505, 0.018896, 0.014000, 0.009498, 0.006074, 0.009480, 0.007611, 0.008958, 0.010086, -0.000341, 0.010423, 0.010467, 0.016794
	-0.072341, -0.064233, -0.079217, -0.084483, -0.091050, -0.094481, -0.095378, -0.096667, -0.100564, -0.098313, -0.093254, -0.086700, -0.079209, -0.071795, -0.061313, -0.051911, -0.046317, -0.042643, -0.037228, -0.031598, -0.027431, -0.020480, -0.012883, -0.003114, 0.004746, 0.010189, 0.015911, 0.017106, 0.014037, 0.008693, 0.005120, 0.003652, -0.000532, -0.001097, 0.001984, 0.000397, -0.002089, -0.002821, 0.000529, 0.009043
	-0.068927, -0.075835, -0.083530, -0.085213, -0.091299, -0.100015, -0.101020, -0.100921, -0.103349, -0.102493, -0.098069, -0.091292, -0.083452, -0.079672, -0.069612, -0.062472, -0.055862, -0.052233, -0.046746, -0.041991, -0.035219, -0.028225, -0.018698, -0.007309, -0.002458, 0.002051, 0.006595, 0.008468, 0.005218, -0.000205, -0.003131, -0.003647, -0.006151, -0.009154, -0.005539, -0.006971, -0.015297, -0.002874, -0.005242, 0.003706
	-0.070116, -0.067835, -0.086390, -0.089881, -0.095167, -0.099194, -0.100751, -0.103794, -0.106996, -0.105835, -0.098564, -0.092154, -0.085579, -0.083053, -0.074722, -0.066442, -0.059302, -0.053429, -0.047800, -0.042952, -0.039132, -0.034614, -0.025732, -0.012689, -0.005906, 0.001101, 0.006644, 0.010980, 0.007742, 0.002526, -0.000261, -0.004094, -0.008771, -0.008465, -0.007095, -0.008952, -0.010405, -0.010446, -0.006121, 0.002024
	-0.064366, -0.071780, -0.082938, -0.085702, -0.093522, -0.099237, -0.104020, -0.105939, -0.106226, -0.104298, -0.097541, -0.091253, -0.084969, -0.082450, -0.075561, -0.066547, -0.056511, -0.051248, -0.041287, -0.037794, -0.035633, -0.028059, -0.019518, -0.010556, -0.003388, 0.002054, 0.009492, 0.011478, 0.008555, 0.004735, -0.000781, -0.006427, -0.005697, -0.010270, -0.006112, -0.011704, -0.018717, -0.002750, -0.010971, 0.000116
	-0.076795, -0.064801, -0.080209, -0.085175, -0.093457, -0.101077, -0.104981, -0.106367, -0.106821, -0.105708, -0.098545, -0.090759, -0.086929, -0.083491, -0.074306, -0.064805, -0.055933, -0.049959, -0.042853, -0.036270, -0.034463, -0.029587, -0.018780, -0.010103, -0.003533, 0.001632, 0.007909, 0.014370, 0.009281, 0.004666, -0.002974, -0.007301, -0.010185, -0.008299, -0.006340, -0.009678, -0.011333, -0.010684, -0.006289, 0.002763
	-0.067470, -0.065770, -0.074038, -0.076420, -0.085702, -0.098704, -0.101940, -0.102629, -0.101903, -0.100342, -0.093820, -0.086941, -0.083804, -0.081020, -0.067700, -0.059395, -0.054055, -0.047911, -0.039687, -0.035672, -0.032029, -0.025979, -0.017057, -0.006973, -0.001656, 0.002001, 0.007249, 0.012112, 0.006541, 0.000572, -0.006284, -0.010415, -0.012279, -0.015087, -0.007848, -0.016491, -0.019704, -0.005357, -0.013151, 0.002966
	-0.074820, -0.054794, -0.069710, -0.075127, -0.082743, -0.091434, -0.095621, -0.097541, -0.099098, -0.097422, -0.089851, -0.083594, -0.081112, -0.078942, -0.066391, -0.057457, -0.050942, -0.048077, -0.041211, -0.034391, -0.030091, -0.026047, -0.014207, -0.005090, 0.000912, 0.005316, 0.010043, 0.015509, 0.011199, 0.004513, -0.001027, -0.006694, -0.011239, -0.011162, -0.009134, -0.013596, -0.014031, -0.011306, -0.007627, 0.001767
	-0.061695, -0.056074, -0.065188, -0.067950, -0.076218, -0.088303, -0.093436, -0.092999, -0.090937, -0.090555, -0.084407, -0.080354, -0.078692, -0.074308, -0.062767, -0.052729, -0.047475, -0.043949, -0.036669, -0.031720, -0.027940, -0.020058, -0.010125, -0.000940, 0.003512, 0.007720, 0.011869, 0.015296, 0.011180, 0.003886, -0.003309, -0.003380, -0.007926, -0.011633, -0.003540, -0.014182, -0.013975, -0.003720, -0.011797, 0.006338
	-0.070864, -0.046187, -0.061128, -0.065717, -0.072715, -0.083470, -0.088292, -0.087558, -0.087628, -0.089378, -0.083768, -0.077237, -0.077063, -0.071978, -0.061635, -0.052022, -0.046913, -0.041194, -0.034314, -0.028661, -0.027048, -0.021438, -0.009769, -0.001205, 0.004637, 0.008928, 0.013264, 0.017277, 0.013442, 0.007295, 0.003623, -0.002524, -0.004256, -0.005789, -0.004213, -0.007305, -0.010487, -0.010885, -0.006086, 0.007386
	-0.059345, -0.049207, -0.056858, -0.060052, -0.066579, -0.080604, -0.086910, -0.085647, -0.085267, -0.087618, -0.081260, -0.075368, -0.073937, -0.069758, -0.058235, -0.051634, -0.045288, -0.038732, -0.032262, -0.027928, -0.024928, -0.019266, -0.007996, 0.000923, 0.005834, 0.008336, 0.013557, 0.017068, 0.012350, 0.006475, 0.000982, 0.001103, -0.006223, -0.006853, -0.000966, -0.013148, -0.013975, -0.006310, -0.011605, 0.006165
	-0.066591, -0.039715, -0.053663, -0.059514, -0.065911, -0.075018, -0.080214, -0.082968, -0.083447, -0.085380, -0.079055, -0.071985, -0.070247, -0.065856, -0.057767, -0.049975, -0.044481, -0.039103, -0.031217, -0.024927, -0.020997, -0.016440, -0.004831, 0.004061, 0.009463, 0.011160, 0.014777, 0.020638, 0.017816, 0.011360, 0.006171, 0.002164, -0.002119, -0.003117, -0.003031, -0.005156, -0.011400, -0.011762, -0.009295, -0.000001
	-0.060314, -0.046160, -0.052794, -0.054967, -0.062049, -0.074106, -0.080446, -0.081200, -0.080809, -0.080477, -0.076170, -0.070932, -0.069101, -0.063634, -0.055720, -0.049501, -0.044939, -0.040131, -0.032438, -0.022882, -0.017627, -0.012524, -0.001324, 0.006685, 0.011868, 0.013658, 0.016095, 0.021837, 0.020158, 0.012528, 0.006089, 0.005453, -0.000976, -0.002140, 0.001104, -0.010111, -0.010612, -0.007452, -0.014357, 0.001011
	-0.075633, -0.036609, -0.049346, -0.055490, -0.059336, -0.067616, -0.073859, -0.075613, -0.076372, -0.078009, -0.070627, -0.064206, -0.064430, -0.061999, -0.054551, -0.047386, -0.040817, -0.037398, -0.028062, -0.018505, -0.012195, -0.007531, 0.001481, 0.011790, 0.019955, 0.022349, 0.022131, 0.024492, 0.023359, 0.019186, 0.014655, 0.008357, 0.004176, 0.002971, 0.002955, -0.000237, -0.005884, -0.010152, -0.009506, 0.002811
	-0.059008, -0.039658, -0.046978, -0.048324, -0.052285, -0.063338, -0.069082, -0.070556, -0.070625, -0.070049, -0.064460, -0.057403, -0.056723, -0.052882, -0.046968, -0.041507, -0.033211, -0.029974, -0.022900, -0.013579, -0.008803, -0.004962, 0.005653, 0.017026, 0.028171, 0.028651, 0.024731, 0.026850, 0.023371, 0.017073, 0.015171, 0.016616, 0.005521, 0.005756, 0.007586, -0.005103, -0.006856, -0.005604, -0.006599, 0.007528
	-0.068330, -0.030233, -0.043154, -0.047439, -0.047149, -0.051149, -0.060971, -0.063014, -0.065775, -0.064636, -0.058200, -0.050987, -0.050925, -0.050115, -0.041299, -0.033907, -0.026306, -0.024199, -0.017123, -0.009196, -0.006314, -0.003809, 0.004760, 0.015324, 0.026665, 0.029649, 0.028724, 0.027131, 0.025150, 0.021808, 0.019981, 0.016766, 0.012347, 0.008776, 0.005760, -0.000224, -0.004294, -0.005879, -0.002457, 0.010054
	-0.053519, -0.031388, -0.038255, -0.037590, -0.039245, -0.046335, -0.056314, -0.057830, -0.060291, -0.058967, -0.051413, -0.045449, -0.043947, -0.042018, -0.034113, -0.025887, -0.019539, -0.017727, -0.012711, -0.005860, -0.003102, 0.000774, 0.009438, 0.015884, 0.022961, 0.024229, 0.026012, 0.029407, 0.026717, 0.020406, 0.017796, 0.020289, 0.012243, 0.009711, 0.009234, -0.005990, -0.001013, 0.000740, -0.002144, 0.013012
	-0.068972, -0.023416, -0.032912, -0.036134, -0.035915, -0.040435, -0.047452, -0.051460, -0.055021, -0.055776, -0.048697, -0.039554, -0.036785, -0.035561, -0.029056, -0.021075, -0.013416, -0.012134, -0.007237, -0.000622, 0.001662, 0.005393, 0.012038, 0.019764, 0.023514, 0.026252, 0.028191, 0.031400, 0.031365, 0.027993, 0.023275, 0.021009, 0.018930, 0.014093, 0.009022, 0.004773, 0.002094, 0.001348, 0.005643, 0.015078
	-0.050527, -0.022437, -0.028090, -0.026206, -0.028387, -0.036911, -0.041310, -0.044227, -0.046970, -0.046769, -0.038081, -0.031386, -0.029516, -0.024050, -0.019435, -0.012381, -0.005732, -0.004173, 0.000911, 0.006849, 0.007360, 0.010699, 0.017436, 0.023369, 0.028527, 0.029640, 0.031002, 0.034727, 0.036582, 0.030763, 0.026015, 0.028623, 0.020834, 0.016185, 0.016933, 0.002829, 0.004984, 0.009818, 0.008874, 0.020032
	-0.067395, -0.010220, -0.021024, -0.024567, -0.024087, -0.029620, -0.032317, -0.034341, -0.038392, -0.038789, -0.030285, -0.021590, -0.017175, -0.014435, -0.007732, -0.000529, 0.005605, 0.007078, 0.012454, 0.017758, 0.016774, 0.015574, 0.020748, 0.028369, 0.033644, 0.034771, 0.036537, 0.040293, 0.042118, 0.039979, 0.035655, 0.033354, 0.030928, 0.024890, 0.021491, 0.018938, 0.013668, 0.012501, 0.017108, 0.023515
	-0.038833, -0.012802, -0.018564, -0.017459, -0.019062, -0.027068, -0.030119, -0.028336, -0.029665, -0.030695, -0.022239, -0.013522, -0.008358, -0.004785, 0.000463, 0.010662, 0.015564, 0.016950, 0.020281, 0.025300, 0.022680, 0.022717, 0.026679, 0.031617, 0.035801, 0.037098, 0.041294, 0.045640, 0.047879, 0.042000, 0.038044, 0.040629, 0.033892, 0.031247, 0.031584, 0.018500, 0.020116, 0.019823, 0.016638, 0.029979
	-0.054356, -0.002258, -0.012712, -0.017288, -0.016713, -0.022907, -0.024293, -0.021563, -0.022620, -0.021953, -0.015330, -0.005386, -0.000764, 0.002640, 0.009997, 0.022869, 0.028174, 0.027730, 0.030977, 0.035707, 0.032818, 0.030889, 0.033638, 0.038561, 0.044265, 0.045141, 0.047683, 0.051815, 0.054004, 0.050991, 0.045574, 0.043899, 0.044055, 0.039092, 0.035909, 0.032091, 0.026891, 0.022169, 0.024865, 0.030848
	-0.031827, -0.000102, -0.006368, -0.006487, -0.006247, -0.014001, -0.017110, -0.013043, -0.010851, -0.008764, -0.000213, 0.006477, 0.011144, 0.018309, 0.024745, 0.033643, 0.038648, 0.039249, 0.041148, 0.045266, 0.041693, 0.040999, 0.045484, 0.052613, 0.057066, 0.054753, 0.055112, 0.059287, 0.060203, 0.052465, 0.047993, 0.050999, 0.047464, 0.046460, 0.044507, 0.031433, 0.032267, 0.032025, 0.029852, 0.040329
	-0.053848, 0.008122, -0.005187, -0.009032, -0.006543, -0.010012, -0.013005, -0.011663, -0.008957, -0.004668, 0.005458, 0.012800, 0.016893, 0.023554, 0.031737, 0.038741, 0.043870, 0.043337, 0.046621, 0.047581, 0.045654, 0.044827, 0.050363, 0.058747, 0.061023, 0.060485, 0.059059, 0.061821, 0.061391, 0.055971, 0.051067, 0.050038, 0.051018, 0.046533, 0.043334, 0.042562, 0.036118, 0.029798, 0.032773, 0.039524
	-0.025830, 0.006164, -0.000655, 0.000164, 0.000088, -0.008033, -0.011008, -0.006017, -0.001301, 0.004088, 0.011848, 0.020276, 0.024465, 0.033383, 0.039126, 0.044268, 0.047916, 0.047402, 0.050050, 0.050456, 0.048891, 0.051771, 0.058154, 0.063246, 0.065463, 0.063072, 0.060950, 0.065351, 0.064614, 0.057455, 0.051194, 0.055723, 0.050906, 0.046407, 0.048283, 0.036561, 0.037400, 0.036887, 0.031589, 0.046759
	-0.041184, 0.017683, 0.006408, 0.000358, 0.001923, -0.002498, -0.003907, -0.001746, 0.001864, 0.006784, 0.017297, 0.026916, 0.030940, 0.036439, 0.045987, 0.050809, 0.054636, 0.052055, 0.053180, 0.056698, 0.057069, 0.055779, 0.063193, 0.067815, 0.071856, 0.070651, 0.067674, 0.070718, 0.070797, 0.062598, 0.057842, 0.056835, 0.056713, 0.051260, 0.048727, 0.048227, 0.044844, 0.039559, 0.041218, 0.044920
	-0.014008, 0.018619, 0.011274, 0.010878, 0.008771, 0.001246, -0.001819, 0.003600, 0.008052, 0.011983, 0.021970, 0.030757, 0.037662, 0.045972, 0.053195, 0.057661, 0.059206, 0.058383, 0.060240, 0.061039, 0.062504, 0.064497, 0.070278, 0.077704, 0.080246, 0.077015, 0.072985, 0.075685, 0.072584, 0.063534, 0.057732, 0.061938, 0.057545, 0.050931, 0.054863, 0.045820, 0.048882, 0.049675, 0.043484, 0.051538
	-0.045038, 0.028947, 0.019821, 0.012917, 0.013648, 0.007951, 0.005122, 0.007823, 0.012411, 0.015320, 0.025036, 0.036734, 0.045314, 0.052208, 0.062220, 0.065610, 0.068489, 0.066665, 0.068454, 0.069025, 0.071080, 0.073373, 0.079623, 0.085651, 0.088907, 0.088954, 0.084254, 0.084464, 0.080300, 0.072471, 0.067316, 0.066430, 0.065143, 0.057630, 0.058650, 0.059627, 0.057197, 0.054105, 0.055295, 0.057879
	-0.017117, 0.027364, 0.023067, 0.022758, 0.019246, 0.011825, 0.007962, 0.011522, 0.017237, 0.021779, 0.031329, 0.042642, 0.052349, 0.060322, 0.069568, 0.074657, 0.075211, 0.072882, 0.075373, 0.078391, 0.079512, 0.081816, 0.086101, 0.091730, 0.095061, 0.095682, 0.092100, 0.092873, 0.085769, 0.077219, 0.068392, 0.073179, 0.069972, 0.061240, 0.068306, 0.062227, 0.061008, 0.064520, 0.058543, 0.070728
	-0.042759, 0.035472, 0.029514, 0.023812, 0.024176, 0.020576, 0.017397, 0.018716, 0.022981, 0.027634, 0.041262, 0.050991, 0.058558, 0.067060, 0.077829, 0.083609, 0.084719, 0.082815, 0.085352, 0.087363, 0.091238, 0.091692, 0.096562, 0.102513, 0.106436, 0.108184, 0.105828, 0.107257, 0.102415, 0.090768, 0.084257, 0.081410, 0.081286, 0.073523, 0.074433, 0.076576, 0.070376, 0.068350, 0.071896, 0.072962
	-0.003143, 0.035517, 0.033266, 0.032727, 0.031843, 0.025862, 0.023177, 0.026936, 0.032953, 0.037457, 0.049289, 0.057429, 0.066625, 0.072540, 0.083814, 0.089321, 0.092420, 0.093053, 0.094752, 0.096876, 0.098364, 0.101271, 0.105185, 0.113505, 0.115784, 0.118957, 0.117138, 0.117934, 0.110930, 0.101497, 0.091051, 0.092731, 0.090574, 0.079282, 0.084691, 0.078426, 0.073451, 0.081698, 0.072811, 0.084352
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 19.8
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 130, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 123, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 112, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/neopixel.py", line 111, in load_config_prefix
    return PrinterNeoPixel(config)
  File "/home/pi/klipper/klippy/extras/neopixel.py", line 42, in __init__
    raise config.error("neopixel chain too long")
configparser.Error: neopixel chain too long
webhooks client 4130895664: New connection
webhooks client 4130895664: Client info {'program': 'Moonraker', 'version': 'v0.9.3-0-g71f9e67'}
Starting Klippy...
Args: ['/home/pi/klipper/klippy/klippy.py', '/home/pi/printer_data/config/printer.cfg', '-l', '/home/pi/printer_data/logs/klippy.log', '-I', '/home/pi/printer_data/comms/klippy.serial', '-a', '/home/pi/printer_data/comms/klippy.sock']
Git version: 'v0.13.0-573-g644cda5ec-dirty'
Untracked files: klippy/extras/beacon.py, klippy/extras/beacon_adaptive_heat_soak.py, klippy/extras/beacon_mesh.py, klippy/extras/beacon_true_zero_correction.py, klippy/extras/beacon_user_z_offset.py, klippy/extras/fastconfig.py, klippy/extras/gcode_shell_command.py, klippy/extras/linear_movement_vibrations.py, klippy/extras/named_offsets.py, klippy/extras/ratos.py, (+4 files)
Branch: master
Remote: origin
Tracked URL: https://github.com/Klipper3d/klipper.git
CPU: 4 core ?
Device: Raspberry Pi 4 Model B Rev 1.5
Linux: Linux version 6.1.21-v8+ (dom@buildbot) (aarch64-linux-gnu-gcc-8 (Ubuntu/Linaro 8.4.0-3ubuntu1) 8.4.0, GNU ld (GNU Binutils for Ubuntu) 2.34) #1642 SMP PREEMPT Mon Apr  3 17:24:16 BST 2023
Python: '3.9.2 (default, Jan 24 2026, 09:41:14) \n[GCC 10.2.1 20210110]'
Building C code module c_helper.so
Start printer at Tue Mar 17 03:56:11 2026 (1773719771.5 9375.9)
===== Config file =====
[mcu rpi]
serial = /tmp/klipper_host_mcu

[board_pins btt-octopus-pro-h723-11]
aliases = 
	
	
	
	x_step_pin=PF13,
	x_dir_pin=PF12,
	x_enable_pin=PF14,
	x_uart_pin=PC4,
	x_diag_pin=PG6,
	x_endstop_pin=PG6,
	
	
	
	dual_carriage_step_pin=PF9,
	dual_carriage_dir_pin=PF10,
	dual_carriage_enable_pin=PG2,
	dual_carriage_uart_pin=PF2,
	dual_carriage_diag_pin=PG12,
	dual_carriage_endstop_pin=PG12,
	
	
	
	y_step_pin=PG0,
	y_dir_pin=PG1,
	y_enable_pin=PF15,
	y_uart_pin=PD11,
	y_diag_pin=PG9,
	y_endstop_pin=PG9,
	
	
	
	y1_step_pin=PG4,
	y1_dir_pin=PC1,
	y1_enable_pin=PA2,
	y1_uart_pin=PC7,
	y1_diag_pin=PG11,
	y1_endstop_pin=PG11,
	
	
	
	z0_step_pin=PC13,
	z0_dir_pin=PF0,
	z0_enable_pin=PF1,
	z0_uart_pin=PE4,
	z0_diag_pin=PG13,
	
	
	
	z1_step_pin=PE2,
	z1_dir_pin=PE3,
	z1_enable_pin=PD4,
	z1_uart_pin=PE1,
	z1_diag_pin=PG14,
	
	
	
	z2_step_pin=PE6,
	z2_dir_pin=PA14,
	z2_enable_pin=PE0,
	z2_uart_pin=PD3,
	z2_diag_pin=PG15,
	
	e_step_pin=PF11,
	e_dir_pin=PG3,
	e_enable_pin=PG5,
	e_uart_pin=PC6,
	
	e_heater_pin=PA2,
	e_sensor_pin=PF4,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=PA7,
	stepper_spi_miso_pin=PA6,
	stepper_spi_sclk_pin=PA5,
	adxl345_cs_pin=PA15,
	bltouch_sensor_pin=PB7,
	bltouch_control_pin=PB6,
	probe_pin=PB7,
	fan_part_cooling_pin=PA8,
	fan_toolhead_cooling_pin=PE5,
	fan_controller_board_pin=PD12,
	heater_bed_heating_pin=PA1,
	heater_bed_sensor_pin=PF3,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PG15,
	filament_sensor_motion_pin=PG14,
	ratrig_vaoc_probe_pin=PG10,
	ratrig_vaoc_led_pin=PB0,
	ratrig_vaoc_fan_pin=PD13,
	chamber_lighting_pin=PB11,
	chamber_filter_4p_fan_pin=PD14,
	chamber_filter_4p_fan_enable_pin=PD15

[mcu]
serial = /dev/RatOS/btt-octopus-pro-h723-11

[temperature_sensor Octopus_Pro_H723_V1.1]
sensor_type = temperature_mcu

[adxl345 controlboard]
cs_pin = PA15
spi_software_mosi_pin = PB5
spi_software_miso_pin = PB4
spi_software_sclk_pin = PB3

[board_pins toolboard_t0]
mcu = toolboard_t0
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t0]
serial = /dev/RatOS/btt-ebb42-gen2-10-t0

[temperature_sensor EBB42_Gen2_v1.0_T0]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t0

[lis2dw toolboard_t0]
axes_map = x, z, y
cs_pin = toolboard_t0:PB1
spi_software_mosi_pin = toolboard_t0:PB11
spi_software_miso_pin = toolboard_t0:PB2
spi_software_sclk_pin = toolboard_t0:PB10

[board_pins toolboard_t1]
mcu = toolboard_t1
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t1]
serial = /dev/RatOS/btt-ebb42-gen2-10-t1

[temperature_sensor EBB42_Gen2_v1.0_T1]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t1

[lis2dw toolboard_t1]
axes_map = x, z, y
cs_pin = toolboard_t1:PB1
spi_software_mosi_pin = toolboard_t1:PB11
spi_software_miso_pin = toolboard_t1:PB2
spi_software_sclk_pin = toolboard_t1:PB10

[gcode_macro RatOS]
variable_homing = "endstops"
variable_z_probe = "static"
variable_sensorless_x_current = 0.6
variable_sensorless_y_current = 0.9
variable_safe_home_x = "middle"
variable_safe_home_y = "middle"
variable_driver_type_x = "tmc2209"
variable_driver_type_y = "tmc2209"
variable_stowable_probe_stop_on_error = False
variable_chamber_filter_enable = True
variable_chamber_filter_speed = 0.5
variable_chamber_filter_disable_speed = 1.0
variable_chamber_filter_enable_at = "after_print_start"
variable_chamber_filter_disable_period = 300
variable_chamber_filter_disable_bed_temp = 0
variable_chamber_heater_enable = True
variable_chamber_heater_bed_temp = 115
variable_chamber_heater_preheating_temp = 150
variable_chamber_heater_heating_temp_offset = 25
variable_chamber_heater_control_external_heater = False
variable_chamber_heater_air_circulation_enable = True
variable_chamber_heater_air_circulation_fan_speed = 0.35
variable_chamber_heater_air_circulation_y_pos = 0
variable_chamber_heater_air_circulation_z_pos = 100
variable_chamber_heater_extra_fan_speed = 1.0
variable_chamber_heater_filter_fan_speed = 1.0
variable_bed_heat_soak_time = 0
variable_hotend_heat_soak_time = 0
variable_led_status_action = 0.0,1.0,1.0
variable_led_status_success = 0.0,1.0,0.0
variable_led_status_error = 1.0,0.0,1.0
variable_led_status_on = 1.0,1.0,1.0
variable_led_status_off = 0.0,0.0,1.0
variable_led_status_standby = 0.1,0.1,0.1
variable_led_status_heating = 1.0,0.0,0.0
variable_led_status_cooling = 0.0,0.0,1.0
variable_calibrate_bed_mesh = True
variable_adaptive_mesh = True
variable_start_print_park_in = "center"
variable_start_print_park_z_height = 3
variable_end_print_park_in = "back"
variable_pause_print_park_in = "back"
variable_end_print_park_z_hop = 20
variable_nozzle_priming = "primeblob"
variable_nozzle_prime_start_x = "max"
variable_nozzle_prime_start_y = "min"
variable_nozzle_prime_direction = "auto"
variable_nozzle_prime_bridge_fan = 102
variable_probe_for_priming_result = None
variable_probe_for_priming_end_result = None
variable_probe_for_priming_result_t1 = None
variable_probe_for_priming_end_result_t1 = None
variable_probe_for_priming_disable_mesh_constraints = False
variable_adaptive_prime_offset_threshold = -1.0
variable_last_z_offset = None
variable_runout_park_in = "front"
variable_enable_unload_tip_forming = False
variable_filament_unload_length = 150
description = RatOS variable storage macro, will echo variables to the console when run.
variable_relative_extrusion = True
variable_force_absolute_position = False
variable_preheat_extruder = True
variable_preheat_extruder_temp = 150
variable_macro_travel_speed = 600
variable_macro_travel_accel = 8000
variable_macro_z_speed = 15
variable_bed_margin_x = [59.6, 59.6]
variable_bed_margin_y = [14.35, 33.65]
variable_printable_x_min = 0
variable_printable_x_max = 0
variable_printable_y_min = 0
variable_printable_y_max = 0
variable_end_print_motors_off = True
variable_status_color_ok = "00FF00"
variable_status_color_error = "FF0000"
variable_status_color_unknown = "FFFF00"
variable_end_print_retract_filament = 10
gcode = 
	ECHO_RATOS_VARS
variable_auto_center_subject = False
variable_toolchange_zhop = 2.0
variable_toolchange_zspeed = 25
variable_toolchange_sync_fans = False
variable_toolchange_combined_zhop = False
variable_toolchange_travel_speed = 600
variable_toolchange_travel_accel = 8000
variable_toolchange_extrusion = 2.0
variable_toolchange_retraction = 2.0
variable_toolchange_feedrate = 7200
variable_toolchange_prepurging_timer = 0
variable_toolchange_standby_temp = -1
variable_toolchange_purge = 25
variable_toolchange_first_purge = 50
variable_beacon_bed_mesh_scv = 25
variable_beacon_contact_z_homing = False
variable_beacon_contact_start_print_true_zero = True
variable_beacon_contact_start_print_true_zero_fuzzy_position = True
variable_beacon_contact_calibrate_model_on_true_zero = True
variable_beacon_contact_wipe_before_true_zero = True
variable_beacon_contact_wipe_before_true_zero_method = "probe_clean"
variable_beacon_contact_true_zero_temp = 170
variable_beacon_contact_prime_probing = True
variable_beacon_contact_expansion_compensation = True
variable_beacon_contact_bed_mesh = False
variable_beacon_contact_bed_mesh_samples = 2
variable_beacon_contact_z_tilt_adjust = False
variable_beacon_contact_z_tilt_adjust_samples = 2
variable_beacon_scan_compensation_enable = True
variable_beacon_scan_compensation_profile = "auto"
variable_beacon_scan_compensation_desired_spacing = 10
variable_beacon_scan_compensation_bed_temp_mismatch_is_error = False
variable_beacon_contact_poke_bottom_limit = -1
variable_beacon_scan_method_automatic = False
variable_beacon_adaptive_heat_soak = True
variable_beacon_adaptive_heat_soak_max_wait = 5400
variable_beacon_adaptive_heat_soak_extra_wait_after_completion = 0
variable_beacon_adaptive_heat_soak_layer_quality = 3
variable_beacon_adaptive_heat_soak_maximum_first_layer_duration = 1800
variable_beacon_contact_start_print_true_zero_fuzzy_radius = 20
variable_homing_x = "endstop"
variable_homing_y = "endstop"
variable_default_toolhead = 0
variable_adxl_chip = ["lis2dw toolboard_t0", "lis2dw toolboard_t1"]
variable_shaper_x_freq = [54.2, 53.2, 53.6, 54.4]
variable_shaper_y_freq = [40.8, 47.6, 38.6, 38]
variable_shaper_x_type = ["mzv", "mzv", "mzv", "mzv"]
variable_shaper_y_type = ["mzv", "mzv", "mzv", "mzv"]
variable_x_driver_types = ["tmc5160"]
variable_x_axes = ["x"]
variable_y_driver_types = ["tmc5160", "tmc5160"]
variable_y_axes = ["y", "y1"]
variable_z_driver_types = ["tmc2209", "tmc2209", "tmc2209"]
variable_z_axes = ["z", "z1", "z2"]
variable_home_y_first = True

[ratos_homing]
axes = xyz
z_hop = 15
z_hop_speed = 15
gcode = 
	
	_LED_ON
	
	
	{% set prev_stop_on_error = printer["gcode_macro RatOS"].stowable_probe_stop_on_error %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set target_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	_IDEX_SINGLE
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE=True
	
	
	M400
	
	G90
	
	
	{% set X = true if params.X is defined else false %}
	{% set Y = true if params.Y is defined else false %}
	{% set Z = true if params.Z is defined else false %}
	{% if printer["gcode_macro RatOS"].home_y_first|default(false)|lower == 'true' %}
	HOME_Y X={X} Y={Y} Z={Z}
	HOME_X X={X} Y={Y} Z={Z}
	{% else %}
	HOME_X X={X} Y={Y} Z={Z}
	HOME_Y X={X} Y={Y} Z={Z}
	{% endif %}
	HOME_Z X={X} Y={Y} Z={Z}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE={prev_stop_on_error}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[gcode_macro HOME_X]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_x = printer["gcode_macro RatOS"].homing_x|lower %}
	{% set homing_x = homing_x if homing_x else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_X" MSG="printable_x_max: {printable_x_max}, safe_home_x: {safe_home_x}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}"
	
	
	{% if X or not Y and not Z %}
	{% if homing_x == 'endstop' %}
	G28 X
	{% elif homing_x == 'sensorless' %}
	{% if printer["dual_carriage"] is defined %}
	{ action_emergency_stop("sensorless homing not supported on IDEX!") }
	{% endif %}
	HOME_X_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_x to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_x, homing)) }
	{% endif %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1} MODE=PRIMARY
	G1 X{parking_position} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	{% endif %}
	{% set x_homed = True %}
	G0 X{safe_home_x} F{speed}
	M400
	{% endif %}

[gcode_macro HOME_Y]
gcode = 
	
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_y = printer["gcode_macro RatOS"].homing_y|lower %}
	{% set homing_y = homing_y if homing_y else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Y" MSG="printable_y_max: {printable_y_max}, safe_home_y: {safe_home_y}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}"
	
	
	{% if Y or not X and not Z %}
	{% if homing_y == 'endstop' %}
	G28 Y
	{% elif homing_y == 'sensorless' %}
	HOME_Y_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_y to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_y, homing)) }
	{% endif %}
	{% set y_homed = True %}
	G0 Y{safe_home_y} F{speed}
	{% endif %}

[gcode_macro HOME_Z]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	
	
	{% set beacon_contact_z_homing = true if printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_z_home_position_fuzzing_radius = printer["gcode_macro RatOS"].beacon_z_home_position_fuzzing_radius|default(0)|float %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Z" MSG="x_homed: {x_homed}, y_homed: {y_homed}, z_probe: {z_probe}, beacon_contact_z_homing: {beacon_contact_z_homing}"
	
	
	{% if Z or not Y and not X %}
	RATOS_ECHO MSG="Homing Z"
	{% if x_homed == False or y_homed == False %}
	{ action_emergency_stop("X and Y must be homed before homing Z") }
	{% else %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_homing %}
	{% if beacon_contact_start_print_true_zero %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% else %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	{% else %}
	G28 Z
	{% endif %}
	_Z_HOP
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro HOME_X_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	
	G4 P300
	
	G28 X
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"

[gcode_macro HOME_Y_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	
	G4 P300
	
	G28 Y
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"

[gcode_macro _Z_HOP]
description = Move Z axis up by Z_HOP distance at Z_HOP_SPEED. In relative mode it will move Z axis up by Z_HOP distance. In absolute mode it will move Z axis to Z_HOP distance.
gcode = 
	{% set z_hop = printer.fastconfig.config.ratos_homing.z_hop|float %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	G0 Z{z_hop} F{z_hop_speed}

[gcode_macro __MOVE_TO_SAFE_Z_HOME_ECHO_DEBUG]
gcode = 
	DEBUG_ECHO PREFIX="_MOVE_TO_SAFE_Z_HOME" MSG="x: {params.X}, y: {params.Y}, z_hop: {params.Z_HOP}, fuzzy_radius: {params.FUZZY_RADIUS}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}, printable_x_max: {printer['gcode_macro RatOS'].printable_x_max}, printable_y_max: {printer['gcode_macro RatOS'].printable_y_max}"

[gcode_macro MAYBE_HOME]
description = Only home unhomed axis. Specify ABL=1 to also ensure that automatic bed levelling is applied (if configured).
variable_is_kinematic_position_overriden = False
gcode = 
	{% set abl = params.ABL|default('')|lower in ('true', 'yes', '1') %}
	{% if printer["gcode_macro MAYBE_HOME"].is_kinematic_position_overriden|lower == 'true' %}
	RATOS_ECHO MSG="SET_CENTER_KINEMATIC_POSITION has been abused. Homing all axes. Please refrain from using SET_CENTER_KINEMATIC_POSITION outside of debugging purposes."
	G28
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=False
	{% else %}
	{% set axes = '' %}
	{% set isHomed = true %}
	{% set axesToHome = '' %}
	{% if params.X is defined %}
	{% set axes = axes ~ 'X ' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% endif %}
	{% if params.Y is defined %}
	{% set axes = axes ~ 'Y ' %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% endif %}
	{% if params.Z is defined %}
	{% set axes = axes ~ 'Z ' %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if params.X is not defined and params.Y is not defined and params.Z is not defined %}
	{% set axes = '' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if isHomed is false %}
	RATOS_ECHO MSG="Homing {axesToHome}"
	G28 {axesToHome}
	{% else %}
	RATOS_ECHO MSG="All requested axes already homed. Skipping homing."
	{% endif %}
	{% endif %}
	{% if abl %}
	{% if printer.z_tilt is defined %}
	{% if not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Performing Z tilt adjustment..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Z tilt already applied. Skipping Z tilt adjustment."
	{% endif %}
	{% elif printer.quad_gantry_level is defined %}
	{% if not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Performing quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Quad gantry leveling already applied. Skipping quad gantry leveling."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="No automatic bed leveling method configured. Skipping bed leveling."
	{% endif %}
	{% endif %}

[gcode_macro PID_CALIBRATE_HOTEND]
description = Perform a PID calibration test for a given extruder heater.
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set temp = params.TEMP|default(220)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_HOTEND" MSG="TEMP={temp}"
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO MSG="PID calibration hotend heater T0 at {temp}°C..."
	PID_CALIBRATE HEATER=extruder TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	
	{% if toolhead==0 or toolhead==1 %}
	RATOS_ECHO MSG="PID calibration hotend heater T{toolhead} at {temp}°C..."
	PID_CALIBRATE HEATER=extruder{'' if toolhead==0 else toolhead} TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_BED]
description = Perform a PID calibration test for the bed heater.
gcode = 
	
	{% set temp = params.TEMP|default(80)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_BED" MSG="TEMP={temp}"
	RATOS_ECHO MSG="PID calibration bed heater at {temp}°C..."
	
	
	PID_CALIBRATE HEATER=heater_bed TARGET={temp}
	
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_CHAMBER_HEATER]
description = Perform a PID calibration test for the chamber heater.
gcode = 
	
	{% set temp = params.TEMP|default(150)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_CHAMBER_HEATER" MSG="TEMP={temp}"
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	RATOS_ECHO MSG="PID calibration chamber heater at {temp}°C..."
	PID_CALIBRATE HEATER=chamber_heater TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_heater" %}
	{% set link_text = "RatOS Chamber Heater" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber heater found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro INITIALIZE_PA_TUNING]
description = Start a pressure advance tuning tower.
gcode = 
	
	{% set start = params.START|default(0.0)|float %}
	{% set factor = params.FACTOR|default(0.001)|float %}
	
	
	{% set layer_number = printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|default(0)|int %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if is_printing_gcode and layer_number < 2 %}
	DEBUG_ECHO PREFIX="START_PA_TOWER" MSG="START: {start}, FACTOR: {factor}"
	RATOS_ECHO MSG="Starting pressure advance tuning tower..."
	TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START={start} FACTOR={factor}
	{% else %}
	RATOS_ECHO MSG="Pressure advance tuning tower requires you to be printing gcode and on layer 1 to start."
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro CHAMBER_FILTER_ON]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	_CHAMBER_FILTER_TURN_ON
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro CHAMBER_FILTER_OFF]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Deactivating chamber filter..."
	_CHAMBER_FILTER_TURN_OFF
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set chamber_filter_enable_at = printer["gcode_macro RatOS"].chamber_filter_enable_at|default('after_print_start')|lower %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_ON" MSG="at: {at}, chamber_filter_enable: {chamber_filter_enable}, chamber_filter_enable_at: {chamber_filter_enable_at}, chamber_filter_speed: {chamber_filter_speed}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	{% if chamber_filter_enable_at == at %}
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	
	
	_CHAMBER_FILTER_TURN_ON AT={at}
	
	
	{% if chamber_filter_enable_at == "print_end" %}
	_LED_CHAMBER_FILTER_ON
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_OFF]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF" MSG="chamber_filter_enable: {chamber_filter_enable}, filter_disable_period: {filter_disable_period}, filter_disable_bed_temp: {filter_disable_bed_temp}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	
	{% if filter_disable_period > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting {filter_disable_period} seconds before turning chamber filter off..."
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION={filter_disable_period}
	{% endif %}
	
	
	{% if filter_disable_bed_temp > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting for bed temp to cool down to {filter_disable_bed_temp}°C to turn filter off..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM=0 MAXIMUM={filter_disable_bed_temp}
	_CHAMBER_FILTER_TURN_OFF
	_LED_CHAMBER_FILTER_OFF
	{% endif %}
	
	{% endif %}

[delayed_gcode _CHAMBER_FILTER_OFF_TIMER]
gcode = 
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF_TIMER" MSG="executed"
	
	
	_CHAMBER_FILTER_TURN_OFF
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Chamber filter turned off!"
	
	
	_LED_CHAMBER_FILTER_OFF

[gcode_macro _CHAMBER_FILTER_TURN_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_speed|default(0)|float %}
	{% if at == "print_end" %}
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_disable_speed|default(0)|float %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION=0
	
	
	SET_FAN_SPEED FAN=filter SPEED={chamber_filter_speed}

[gcode_macro _CHAMBER_FILTER_TURN_OFF]
gcode = 
	
	SET_FAN_SPEED FAN=filter SPEED=0

[gcode_macro _CHAMBER_FILTER_SANITY_CHECK]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	{% if filter_disable_bed_temp > 0 and filter_disable_period > 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable, not both.")}
	{% endif %}
	
	{% if filter_disable_bed_temp == 0 and filter_disable_period == 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable.")}
	{% endif %}
	
	{% endif %}

[gcode_macro CHAMBER_HEATER_ON]
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(45)|int %}
	
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp} IS_FROM_START_PRINT=False

[gcode_macro CHAMBER_HEATER_OFF]
gcode = 
	_CHAMBER_HEATER_OFF

[gcode_macro _CHAMBER_HEATER_ON]
variable_chamber_temp = 0
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	{% set is_from_start_print = true if params.IS_FROM_START_PRINT|default(True)|lower == 'true' else false %}
	
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set chamber_heater_enable = true if printer["gcode_macro RatOS"].chamber_heater_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}
	{% set chamber_heater_preheating_temp = printer["gcode_macro RatOS"].chamber_heater_preheating_temp|default(150)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	{% set chamber_heater_control_external_heater = true if printer["gcode_macro RatOS"].chamber_heater_control_external_heater|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_enable = true if printer["gcode_macro RatOS"].chamber_heater_air_circulation_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_fan_speed = printer["gcode_macro RatOS"].chamber_heater_air_circulation_fan_speed|default(0.35)|float %}
	{% set chamber_heater_air_circulation_y_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_y_pos|default(0)|float %}
	{% set chamber_heater_air_circulation_z_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_z_pos|default(100)|float %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_HEATER_ON" MSG="chamber_heater_enable: {chamber_heater_enable}, chamber_heater_preheating_temp: {chamber_heater_preheating_temp}, chamber_heater_heating_temp_offset: {chamber_heater_heating_temp_offset}, bed_temp: {bed_temp}, chamber_temp: {chamber_temp}, start_chamber_temp: {start_chamber_temp}"
	
	
	{% if chamber_heater_enable and chamber_temp > 0 and chamber_heater_bed_temp > 0 %}
	
	
	_LED_HEATING
	
	
	RATOS_ECHO MSG="Preheating chamber to {(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}°C..."
	
	
	{% set chamber_temp_sensor = "extruder" %}
	{% if printer["dual_carriage"] is defined and default_toolhead == 1 %}
	{% set chamber_temp_sensor = "extruder1" %}
	{% endif %}
	{% if printer["temperature_sensor chamber"] is defined %}
	{% set chamber_temp_sensor = "temperature_sensor chamber" %}
	{% endif %}
	
	
	{% set current_chamber_temp = printer['%s' % chamber_temp_sensor].temperature|int %}
	
	
	{% set needs_heating = current_chamber_temp < (start_chamber_temp if start_chamber_temp > 0 else chamber_temp) %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_BEFORE_PREHEATING
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	{% if not is_from_start_print %}
	MAYBE_HOME
	{% endif %}
	G0 Z{chamber_heater_air_circulation_z_pos} F{z_speed}
	G0 Y{chamber_heater_air_circulation_y_pos} F{speed}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * chamber_heater_air_circulation_fan_speed)}
	{% endif %}
	{% else %}
	{% if is_from_start_print %}
	G0 Z{z} F{z_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE={chamber_temp}
	
	
	{% if needs_heating %}
	
	
	M140 S{chamber_heater_bed_temp}
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={chamber_heater_preheating_temp}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	
	{% endif %}
	
	
	{% if needs_heating %}
	_CHAMBER_HEATER_EXTRA_FAN_ON
	{% endif %}
	
	
	{% if needs_heating %}
	TEMPERATURE_WAIT SENSOR="{chamber_temp_sensor}" MINIMUM={(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% endif %}
	
	
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED=0
	_CHAMBER_FILTER_ON AT="before_print_start"
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	G28 Z
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_AFTER_PREHEATING
	{% endif %}
	
	
	{% if printer["temperature_sensor chamber"] is defined %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined and chamber_heater_control_external_heater %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	
	
	_LED_SUCCESS
	
	{% endif %}

[gcode_macro _CHAMBER_HEATER_OFF]
gcode = 
	RATOS_ECHO MSG="Deactivating chamber heater..."
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=0
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE=0
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	
	
	_CHAMBER_HEATER_EXTRA_FAN_OFF

[delayed_gcode _CHAMBER_HEATER_CONTROL]
initial_duration = 0.
gcode = 
	
	{% set chamber_temp = printer["gcode_macro _CHAMBER_HEATER_ON"].chamber_temp|default(0)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	
	
	{% set current_chamber_temp = printer['temperature_sensor chamber'].temperature|int %}
	
	
	{% if current_chamber_temp < chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	{% endif %}
	
	
	{% if current_chamber_temp >= chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_ON]
gcode = 
	
	{% set chamber_heater_extra_fan_speed = printer["gcode_macro RatOS"].chamber_heater_extra_fan_speed|default(0.0)|float %}
	
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	{% if chamber_heater_extra_fan_speed > 0 %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED={chamber_heater_extra_fan_speed}
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_OFF]
gcode = 
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED=0
	{% endif %}

[gcode_macro _USER_CHAMBER_HEATER_BEFORE_PREHEATING]
description = Will be executed before chamber preheating, only if heating is needed.
gcode = 

[gcode_macro _USER_CHAMBER_HEATER_AFTER_PREHEATING]
description = Will be executed after chamber preheating, only if heating was needed.
gcode = 

[gcode_macro RESET_HEATSOAK_SETTINGS]
description = Resets all heatsoak-related settings to startup defaults
gcode = 
	HEATSOAK_SETTINGS ACTION=reset

[gcode_macro USE_ADAPTIVE_HEATSOAK]
description = Temporarily enables adaptive bed heatsoaking (if a beacon probe is present), will reset to printer.cfg settings
	when Klipper is restarted. Optionally specify QUALITY (1-5) and maximum FIRST_LAYER_DURATION (in minutes).
	Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.QUALITY|default("1..5") %}
	{% set _ = params.FIRST_LAYER_DURATION|default("1..120 minutes") %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("Adaptive heatsoaking is only available when a beacon probe is configured.") }
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_quality = (settings.variable_beacon_adaptive_heat_soak_layer_quality if defsrc == 'startup' else current.beacon_adaptive_heat_soak_layer_quality)|default(3)|int %}
	{% set default_first_layer_duration_secs = (settings.variable_beacon_adaptive_heat_soak_maximum_first_layer_duration if defsrc == 'startup' else current.beacon_adaptive_heat_soak_maximum_first_layer_duration)|default(1800)|int %}
	{% if params2.QUALITY is defined %}
	{% set quality = params2.QUALITY|int %}
	{% if quality < 1 or quality > 5 %}
	{ action_raise_error("QUALITY must be between 1 (rough) and 5 (maximum). Use 3 (normal) if unsure.") }
	{% endif %}
	{% else %}
	{% set quality = default_quality %}
	{% endif %}
	{% if params2.FIRST_LAYER_DURATION is defined %}
	{% set first_layer_duration_mins = params2.FIRST_LAYER_DURATION|float %}
	{% if first_layer_duration_mins <= 0 %}
	{ action_raise_error("FIRST_LAYER_DURATION must be a positive number specifying the maximum first layer duration in minutes.") }
	{% endif %}
	{% if first_layer_duration_mins > 120 %}
	CONSOLE_ECHO MSG="FIRST_LAYER_DURATION will be limited to 120 minutes. Values larger than this will not have an effect on soak time."
	{% set first_layer_duration_mins = 120 %}
	{% endif %}
	{% set first_layer_duration_secs = (first_layer_duration_mins * 60.0)|int %}
	{% else %}
	{% set first_layer_duration_secs = default_first_layer_duration_secs %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	{% endif %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=True beacon_adaptive_heat_soak_layer_quality={quality} beacon_adaptive_heat_soak_maximum_first_layer_duration={first_layer_duration_secs}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."

[gcode_macro USE_FIXED_HEATSOAK]
description = Temporarily enables fixed bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
	Optionally specify DURATION (in minutes). Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.DURATION|default("0..720 minutes") %}
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_duration = (settings.variable_bed_heat_soak_time if defsrc == 'startup' else current.bed_heat_soak_time)|default(0)|int %}
	{% if params2.DURATION is defined %}
	{% set duration_mins = params2.DURATION|float %}
	{% if duration_mins < 0 %}
	{ action_raise_error("DURATION must be a non-negative number specifying the heatsoak duration in minutes.") }
	{% endif %}
	{% if duration_mins > 720 %}
	CONSOLE_ECHO MSG="DURATION will be limited to 720 minutes (12 hours). If you really need a larger value, adjust printer.cfg instead."
	{% set duration_mins = 720 %}
	{% endif %}
	{% set duration_secs = (duration_mins * 60.0)|int %}
	{% else %}
	{% set duration_secs = default_duration %}
	{% set duration_mins = duration_secs / 60.0 %}
	{% endif %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% if has_beacon %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=False bed_heat_soak_time={duration_secs}
	{% else %}
	HEATSOAK_SETTINGS QUIET=1 bed_heat_soak_time={duration_secs}
	{% endif %}
	{% if duration_mins < 1e-3 %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% else %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% endif %}

[gcode_macro USE_NO_HEATSOAK]
description = Temporarily disables bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
gcode = 
	USE_FIXED_HEATSOAK DURATION=0

[gcode_macro HEATSOAK_SETTINGS]
description = Shows or adjusts heatsoak settings
	- With no arguments: shows current heatsoak settings, specify VERBOSE=1 for detailed output
	- With arguments: sets the specified settings. Use the full setting name without the variable_ prefix, e.g. bed_heat_soak_time=300 or beacon_adaptive_heat_soak_layer_quality=4. See printer.cfg for available settings.
variable_default_source = "startup"
gcode = 
	
	{% set params2 = params %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% set quiet = params2.pop("QUIET", None)|default("0") in ("1", "true", "yes") %}
	{% set verbose = params2.pop("VERBOSE", None)|default("0") in ("1", "true", "yes") %}
	{% if has_beacon %}
	{% set vars = (
	"beacon_adaptive_heat_soak",
	"beacon_adaptive_heat_soak_max_wait",
	"beacon_adaptive_heat_soak_extra_wait_after_completion",
	"beacon_adaptive_heat_soak_layer_quality",
	"beacon_adaptive_heat_soak_maximum_first_layer_duration",
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% else %}
	{% set vars = (
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% endif %}
	{% set action = "show" if params|length == 0 else params2.ACTION %}
	{% if action is defined and params|length > 1 %}
	{ action_raise_error("ACTION cannot be specified with other parameters.") }
	{% elif action is not defined %}
	{% for k, v in params2.items() %}
	{% set k = k|lower %}
	{% if k in vars %}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Setting {k} to {v}"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={k} VALUE={v}
	{% else %}
	{ action_raise_error("Parameter '%s' is not recognised. Note that adaptive heatsoaking settings can only be set when a beacon probe is configured." % k) }
	{% endif %}
	{% endfor %}
	{% elif action == "reset" %}
	_RESET_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	CONSOLE_ECHO MSG="Heatsoak settings have been reset to their original values."
	{% elif action == "show" %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% set is_adaptive = False if not has_beacon else current.beacon_adaptive_heat_soak|default("")|lower == "true" %}
	{% if is_adaptive %}
	{% set quality = current.beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set first_layer_duration_secs = current.beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."
	{% elif current.bed_heat_soak_time|default(0)|int > 0 %}
	{% set duration_mins = (current.bed_heat_soak_time|int / 60.0) %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% else %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% endif %}
	{% if verbose %}
	CONSOLE_ECHO MSG="Detailed settings:"
	_SHOW_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	{% endif %}
	{% else %}
	{ action_raise_error("Action '%s' is not recognised" % action) }
	{% endif %}

[gcode_macro _LED_START_PRINTING]
gcode = 
	_LED_ACTION

[gcode_macro _LED_START_PRINTING_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_PRINTING]
gcode = 
	_LED_ON TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_PAUSE]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_ON]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_OFF]
gcode = 
	_LED_STANDBY

[gcode_macro _LED_LOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_LOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_RUNOUT]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_CLOG]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_UNLOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_UNLOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_DEACTIVATE_TOOLHEAD]
gcode = 
	_LED_OFF TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_STANDBY]
gcode = 
	_LED_STANDBY TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_WAKEUP]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_MOTORS_OFF]
gcode = 
	_LED_STANDBY
	_LED_VAOC_OFF

[gcode_macro _LED_INPUT_SHAPER_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_INPUT_SHAPER_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_BEACON_CALIBRATION_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_VAOC_ON]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=1.0 GREEN=1.0 BLUE=1.0
	{% endif %}

[gcode_macro _LED_VAOC_OFF]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=0.0 GREEN=0.0 BLUE=0.0
	{% endif %}

[gcode_macro _LED_ACTION]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_action %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SUCCESS]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_success %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_HEATING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_heating %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_COOLING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_cooling %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ERROR]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_error %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ON]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_on %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_OFF]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_off %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_STANDBY]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_standby %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}
	
	{% if toolhead >= 0 %}
	{% if printer['neopixel nozzle_led_t%s' % toolhead] is defined  %}
	SET_LED LED={'nozzle_led_t%s' % toolhead} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% else %}
	{% if printer['neopixel nozzle_led_t0'] is defined  %}
	SET_LED LED={'nozzle_led_t0'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% if printer['neopixel nozzle_led_t1'] is defined %}
	SET_LED LED={'nozzle_led_t1'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% endif %}
	
	_USER_LED_SET { rawparams }

[gcode_macro _USER_LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}

[gcode_macro LOAD_FILAMENT]
description = Loads new filament. Note: be careful with PETG, make sure you inspect the tip of your filament before loading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% if filament_name == '' or filament_type == '' %}
	{% set filament_name = 'unknown' %}
	{% set filament_type = 'unknown' %}
	{% endif %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_LOAD_FILAMENT TEMP={temp} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_LOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_LOAD_FILAMENT]
description = Load filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_LOAD_FILAMENT" MSG="TEMP={temp}"
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=load_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	_LOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	
	
	RESTORE_GCODE_STATE NAME=load_state
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament load routine complete, please check that the filament was loaded correctly."

[gcode_macro _IDEX_LOAD_FILAMENT]
description = Load filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament into T{toolhead}..."
	
	DEBUG_ECHO PREFIX="_IDEX_LOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	_LOAD_FILAMENT TOOLHEAD={toolhead} TEMP={temp} AUTOMATED={automated}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="Filament load routine for T{toolhead} complete, please check that the filament was loaded correctly."

[gcode_macro _LOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default(false)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE TOOLHEAD={toolhead}
	_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into hotend.."
	G92 E0
	G0 E{extruder_gear_to_cooling_position_distance} F{extruder_load_speed}
	G92 E0
	M400
	RATOS_ECHO MSG="Filament loaded into hotend."

[gcode_macro _LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set load_speed = printer["gcode_macro T%s" % toolhead].filament_load_speed|float * 60 %}
	{% set filament_loading_nozzle_offset = printer["gcode_macro T%s" % toolhead].filament_loading_nozzle_offset|float %}
	{% set cooling_position_to_nozzle_distance = printer["gcode_macro T%s" % toolhead].cooling_position_to_nozzle_distance|float %}
	{% set purge_after_load = printer["gcode_macro T%s" % toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into nozzle... Please wait!"
	G92 E0
	
	G0 E{cooling_position_to_nozzle_distance + filament_loading_nozzle_offset} F{load_speed}
	G92 E0
	G4 P1000
	_PURGE_FILAMENT	TOOLHEAD={toolhead} E={purge_after_load}
	RATOS_ECHO MSG="Filament loaded into nozzle!"

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"
	
	
	{% set filament_grabbing_length = printer["gcode_macro T%s" % toolhead].filament_grabbing_length|float %}
	{% set filament_grabbing_speed = printer["gcode_macro T%s" % toolhead].filament_grabbing_speed|float %}
	{% set resume_after_insert = true if printer["gcode_macro T%s" % toolhead].resume_after_insert|default(true)|lower == 'true' else false %}
	{% set enable_insert_detection = true if printer["gcode_macro T%s" % toolhead].enable_insert_detection|default(true)|lower == 'true' else false %}
	
	
	{% set current_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	
	{% if enable_insert_detection %}
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="toolhead: {toolhead}, filament_grabbing_length: {filament_grabbing_length}, filament_grabbing_speed: {filament_grabbing_speed}, current_idex_mode: {current_idex_mode}"
	
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	RATOS_ECHO MSG="Filament inserted into T{toolhead}, loading..."
	
	
	FORCE_MOVE STEPPER={'extruder%s' % ('' if toolhead == 0 else toolhead)} DISTANCE={filament_grabbing_length} VELOCITY={filament_grabbing_speed}
	M400
	
	
	{% if printer.pause_resume.is_paused %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% if resume_after_insert %}
	RESUME
	{% endif %}
	{% else %}
	{% if not printer.virtual_sdcard.is_active %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"

[gcode_macro _PURGE_BEFORE_UNLOAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set purge_before_unload = printer["gcode_macro T%s" % toolhead].purge_before_unload|float %}
	
	DEBUG_ECHO PREFIX="_PURGE_BEFORE_UNLOAD" MSG="TOOLHEAD: {toolhead}"
	
	
	{% if purge_before_unload > 0 %}
	G92 E0
	G0 E{purge_before_unload} F300
	G92 E0
	M400
	{% endif %}

[gcode_macro _PURGE_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set e = params.E|int %}
	{% set r = params.R|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_PURGE_FILAMENT" MSG="TOOLHEAD: {toolhead}, E: {e}"
	
	
	{% if e > 0 %}
	
	
	G92 E0
	G0 E{e} F300
	G92 E0
	M400
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={0.4 if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={0.4 if toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * 0.4)}
	{% endif %}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if r > 0 %}
	G92 E0
	G0 E-{r} F300
	G92 E0
	M400
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro _MOVE_TO_LOADING_POSITION]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_MOVE_TO_LOADING_POSITION" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	
	G1 X{loading_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _CLEANING_MOVE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_CLEANING_MOVE" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].parking_position is defined and printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set parking_position = printer["gcode_macro T%s" % toolhead].parking_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	{% set cleaning_position = loading_position %}
	{% if loading_position == parking_position %}
	{% if loading_position > 0 %}
	{% set cleaning_position = loading_position - 30 %}
	{% else %}
	{% set cleaning_position = loading_position + 30 %}
	{% endif %}
	{% endif %}
	
	
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _BED_MESH_SANITY_CHECK]
gcode = 
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is defined %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_start_print_true_zero_fuzzy_position %}
	CONSOLE_ECHO TYPE="error" TITLE="Defined zero reference not compatible with fuzzy true zero" MSG="Using fuzzy start print true zero position is not compatible with a defined zero_reference_position value in the [bed_mesh] section in printer.cfg._N_Please remove the zero_reference_position value from the [bed_mesh] section, or disable fuzzy true zero position in printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_start_print_true_zero_fuzzy_position: False"
	_STOP_AND_RAISE_ERROR MSG="Defined zero reference not compatible with fuzzy true zero"
	{% elif zero_ref_pos[0]|float|round != safe_home_x|float|round or zero_ref_pos[1]|float|round != safe_home_y|float|round %}
	CONSOLE_ECHO TYPE="error" TITLE="Zero reference position does not match safe home position" MSG="Please update your bed mesh zero reference position in printer.cfg, like so:_N__N_[bed_mesh]_N_zero_reference_position: {safe_home_x|float|round},{safe_home_y|float|round}_N_"
	_STOP_AND_RAISE_ERROR MSG="Zero reference position does not match safe home position"
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_bed_mesh %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact bed mesh is enabled" MSG="Beacon contact bed mesh is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_bed_mesh: False"
	{% endif %}
	
	{% if beacon_scan_method_automatic %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon 'automatic' scan method is enabled" MSG="Beacon 'automatic' scan method is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_scan_method_automatic: False"
	{% endif %}
	
	{% if beacon_contact_z_tilt_adjust %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact z-tilt adjust is enabled" MSG="Beacon contact z-tilt adjust is enabled. This is not recommended for normal use and may result in inaccurate z-tilt adjustment._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_z_tilt_adjust: False"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH]
gcode = 
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE=None
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE=None
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION {rawparams}
	{% endif %}

[gcode_macro _START_PRINT_BED_MESH]
variable_actual_true_zero_position_x = None
variable_actual_true_zero_position_y = None
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set X=[params.X0|default(-1)|float, params.X1|default(-1)|float] %}
	{% set Y=[params.Y0|default(-1)|float, params.Y1|default(-1)|float] %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_BED_MESH" MSG="idex_mode: {idex_mode}, X: {X}, Y: {Y}"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is not defined %}
	{% set zero_ref_pos = [safe_home_x if actual_true_zero_position_x is none else actual_true_zero_position_x, safe_home_y if actual_true_zero_position_y is none else actual_true_zero_position_y] %}
	{% endif %}
	
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	
	
	
	
	{% set X=[0, printable_x_max] %}
	{% endif %}
	
	
	{% set beacon_bed_mesh_scv = printer["gcode_macro RatOS"].beacon_bed_mesh_scv|default(25)|int %}
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% if printer.fastconfig.settings.beacon is defined and not beacon_contact_bed_mesh %}
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={beacon_bed_mesh_scv}
	{% endif %}
	
	
	{% set default_profile = printer["gcode_macro RatOS"].bed_mesh_profile|default('ratos') %}
	{% if printer["gcode_macro RatOS"].calibrate_bed_mesh|lower == 'true' %}
	BED_MESH_CLEAR
	{% if printer["gcode_macro RatOS"].adaptive_mesh|lower == 'true' %}
	CALIBRATE_ADAPTIVE_MESH PROFILE="{default_profile}" X0={X[0]} X1={X[1]} Y0={Y[0]} Y1={Y[1]} T={params.T|int} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={idex_mode} ZERO_REF_POS_X={zero_ref_pos[0]} ZERO_REF_POS_Y={zero_ref_pos[1]}
	{% else %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	BED_MESH_PROFILE LOAD="{default_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	
	{% elif printer["gcode_macro RatOS"].bed_mesh_profile is defined %}
	BED_MESH_CLEAR
	BED_MESH_PROFILE LOAD="{printer["gcode_macro RatOS"].bed_mesh_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"

[gcode_macro CALIBRATE_ADAPTIVE_MESH]
gcode = 
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set default_profile = params.PROFILE %}
	
	
	{% set x0 = params.X0|default(-1)|float %}
	{% set y0 = params.Y0|default(-1)|float %}
	{% set x1 = params.X1|default(-1)|float %}
	{% set y1 = params.Y1|default(-1)|float %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Received coordinates X0={x0|round(1)} Y0={y0|round(1)} X1={x1|round(1)} Y1={y1|round(1)}"
	
	{% if x0 >= x1 or y0 >= y1 %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Invalid coordinates received. Please check your slicer settings. Falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	
	
	{% if params.ZERO_REF_POS_X is defined and params.ZERO_REF_POS_Y is defined %}
	{% set zero_ref_pos_x = params.ZERO_REF_POS_X|float %}
	{% set zero_ref_pos_y = params.ZERO_REF_POS_Y|float %}
	{% if zero_ref_pos_x < x0 or zero_ref_pos_x > x1 or zero_ref_pos_y < y0 or zero_ref_pos_y > y1 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Zero reference position X={zero_ref_pos_x|round(1)} Y={zero_ref_pos_y|round(1)} is outside the mesh region, expanding mesh region to include it."
	{% set x0 = [x0, zero_ref_pos_x]|min %}
	{% set y0 = [y0, zero_ref_pos_y]|min %}
	{% set x1 = [x1, zero_ref_pos_x]|max %}
	{% set y1 = [y1, zero_ref_pos_y]|max %}
	{% endif %}
	{% endif %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float %}
	
	
	{% set mesh_x0 = [[x0, max_x]|min, min_x]|max %}
	{% set mesh_y0 = [[y0, max_y]|min, min_y]|max %}
	{% set mesh_x1 = [[x1, max_x]|min, min_x]|max %}
	{% set mesh_y1 = [[y1, max_y]|min, min_y]|max %}
	
	{% if mesh_x0 == min_x and mesh_y0 == min_y and mesh_x1 == max_x and mesh_y1 == max_y %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Print is using the full bed, falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	
	{% set probe_count_x = mesh_config.probe_count.split(",")[0]|int %}
	{% if mesh_config.probe_count.split(",")|length == 2 %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[1]|int %}
	{% else %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[0]|int %}
	{% endif %}
	
	
	{% set probe_x_step = (max_x - min_x) / probe_count_x %}
	{% set probe_y_step = (max_y - min_y) / probe_count_y %}
	
	
	{% set mesh_count_x = ([(mesh_x1 - mesh_x0) / probe_x_step, 3]|max)|int %}
	{% set mesh_count_y = ([(mesh_y1 - mesh_y0) / probe_y_step, 3]|max)|int %}
	{% set min_mesh_count = [mesh_count_x, mesh_count_y]|min %}
	{% set max_mesh_count = [mesh_count_x, mesh_count_y]|max %}
	
	
	{% set algorithm = mesh_config.algorithm %}
	{% if algorithm|lower == 'lagrange' and max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="cannot exceed a probe_count of 6 when using lagrange interpolation. Falling back to bicubic interpolation."
	{% set algorithm = 'bicubic' %}
	{% endif %}
	{% if algorithm|lower == 'bicubic' and min_mesh_count < 4 %}
	{% if max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="invalid probe_count option when using bicubic interpolation. Combination of 3 points on one axis with more than 6 on another is not permitted. Forcing minimum mesh count to be 4."
	{% set min_mesh_count = 4 %}
	{% else %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="bicubic interpolation with a probe_count of less than 4 points detected. Forcing lagrange interpolation."
	{% set algorithm = 'lagrange' %}
	{% endif %}
	{% endif %}
	
	{% set mesh_count_x = ([min_mesh_count, mesh_count_x]|max)|int %}
	{% set mesh_count_x = ([max_mesh_count, mesh_count_x]|min)|int %}
	{% set mesh_count_y = ([min_mesh_count, mesh_count_y]|max)|int %}
	{% set mesh_count_y = ([max_mesh_count, mesh_count_y]|min)|int %}
	
	{% set should_prime = printer["gcode_macro RatOS"].nozzle_priming == 'primeblob' %}
	{% if printer["dual_carriage"] is not defined %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% else %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 != 0 and probe_first %}
	{% set probe_first = false %}
	{% elif printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 == 0 and not probe_first %}
	{% set probe_first = true %}
	{% endif %}
	
	
	{% if should_prime and probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="mesh coordinates X0={mesh_x0|round(1)} Y0={mesh_y0|round(1)} X1={mesh_x1|round(1)} Y1={mesh_y1|round(1)}"
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y} RELATIVE_REFERENCE_INDEX=-1
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	
	
	{% if should_prime and not probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro M84]
rename_existing = M84.1
gcode = 
	
	M84.1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_OFFSET X=0 Y=0
	
	
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro _VAOC"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False
	{% endif %}
	
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	SET_SKEW CLEAR=1
	
	
	_LED_MOTORS_OFF

[gcode_macro M104]
rename_existing = M104.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M104" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set temperature_offset_t0 = printer["gcode_macro T0"].temperature_offset|default(0)|int %}
	{% set temperature_offset_t1 = printer["gcode_macro T1"].temperature_offset|default(0)|int %}
	{% set s0 = [s + temperature_offset_t0, 0]|max %}
	{% set s1 = [s + temperature_offset_t1, 0]|max %}
	{% if temperature_offset_t0 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t0}°C added to toolhead T0."
	{% endif %}
	{% if temperature_offset_t1 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t1}°C added to toolhead T1."
	{% endif %}
	{% else %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	M104.1 S{s0} T0
	M104.1 S{s1} T1
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% else %}
	M104.1 S{s} T{t}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M109]
rename_existing = M109.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M109" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M109" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	M109.1 S{s} T{t}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro SET_HEATER_TEMPERATURE]
rename_existing = SET_HEATER_TEMPERATURE_BASE
gcode = 
	
	{% set heater = params.HEATER|default("") %}
	{% set target = params.TARGET|default(0)|int %}
	
	DEBUG_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="heater: {heater}, target: {target}"
	
	{% set t = -1 %}
	{% if heater|lower == "extruder" or heater|lower == "extruder1" %}
	
	{% set t = 0 if heater|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and target > 0 %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set target = [target + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE_BASE HEATER="{heater}" TARGET={target}
	
	{% if t != -1 and printer.fastconfig.settings.beacon is defined %}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro TEMPERATURE_WAIT]
rename_existing = TEMPERATURE_WAIT_BASE
gcode = 
	
	{% set sensor = params.SENSOR|default("") %}
	{% set minimum = params.MINIMUM|default(-1)|int %}
	{% set maximum = params.MAXIMUM|default(-1)|int %}
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="sensor: {sensor}, minimum: {minimum}, maximum: {maximum}"
	
	{% set t = -1 %}
	{% if sensor|lower == "extruder" or sensor|lower == "extruder1" %}
	
	{% set t = 0 if sensor|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and (minimum > 0 or maximum > 0) %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% if minimum > -1 %}
	{% set minimum = [minimum + temperature_offset, 0]|max %}
	{% endif %}
	{% if maximum > -1 %}
	{% set maximum = [maximum + temperature_offset, 0]|max %}
	{% endif %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set id = "sensor " ~ sensor if t == -1 else "toolhead T" ~ t %}
	
	
	{% if minimum > -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum} MAXIMUM={maximum}
	{% elif minimum > -1 and maximum == -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum}
	{% elif minimum == -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MAXIMUM={maximum}
	{% else %}
	
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="neither MINIMUM or MAXIMUM args were specified, call TEMPERATURE_WAIT_BASE is expected to fail"
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}"
	{% endif %}
	
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature for {id} reached."

[gcode_macro SDCARD_PRINT_FILE]
rename_existing = SDCARD_PRINT_FILE_BASE
gcode = 
	{% if printer["ratos"] is defined %}
	PROCESS_GCODE_FILE { rawparams }
	{% else %}
	SDCARD_PRINT_FILE_BASE { rawparams }
	{% endif %}

[gcode_macro SKEW_PROFILE]
rename_existing = SKEW_PROFILE_BASE
variable_loaded_profile = ""
gcode = 
	{% if params.LOAD is defined %}
	{% if printer.fastconfig.settings["skew_correction %s" % params.LOAD] is defined %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='"{params.LOAD}"'
	{% endif %}
	{% endif %}
	
	SKEW_PROFILE_BASE { rawparams }

[gcode_macro SET_SKEW]
rename_existing = SET_SKEW_BASE
gcode = 
	{% if params.CLEAR is defined %}
	{% if params.CLEAR|default(0)|int == 1 %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='""'
	{% endif %}
	{% endif %}
	
	SET_SKEW_BASE { rawparams }

[gcode_macro SET_VELOCITY_LIMIT]
rename_existing = SET_VELOCITY_LIMIT_BASE
gcode = 
	{% if params.ACCEL_TO_DECEL is defined %}
	
	{% if params.ACCEL is defined %}
	{% set accel = params.ACCEL|float %}
	{% else %}
	{% set accel = printer.toolhead.max_accel|float %}
	{% endif %}
	
	{% if params.VELOCITY is defined %}
	{% set velocity = params.VELOCITY|float %}
	{% else %}
	{% set velocity = printer.toolhead.max_velocity|float %}
	{% endif %}
	
	{% if params.SQUARE_CORNER_VELOCITY is defined %}
	{% set scv = params.SQUARE_CORNER_VELOCITY|float %}
	{% else %}
	{% set scv = printer.toolhead.square_corner_velocity|float %}
	{% endif %}
	
	{% set mcr = params.ACCEL_TO_DECEL|float / accel %}
	
	DEBUG_ECHO PREFIX="SET_VELOCITY_LIMIT" MSG="ACCEL={accel}, VELOCITY={velocity}, SQUARE_CORNER_VELOCITY={scv}, MINIMUM_CRUISE_RATIO={mcr}"
	
	SET_VELOCITY_LIMIT_BASE ACCEL={accel} VELOCITY={velocity} SQUARE_CORNER_VELOCITY={scv} MINIMUM_CRUISE_RATIO={1-mcr}
	
	{% else %}
	
	SET_VELOCITY_LIMIT_BASE { rawparams }
	
	{% endif %}

[gcode_macro BED_MESH_CALIBRATE]
rename_existing = _BED_MESH_CALIBRATE_BASE
variable_abl_and_home_z_if_required = True
gcode = 
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	{% if abl_and_home_z_if_required %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% endif %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set beacon_default_probe_method = printer.fastconfig.settings.beacon.default_probe_method|default('proximity') %}
	{% set probe_method = params.PROBE_METHOD|default(beacon_default_probe_method)|lower %}
	{% if probe_method == 'proximity' %}
	_CHECK_ACTIVE_BEACON_MODEL_TEMP TITLE="Bed mesh calibration warning"
	{% endif %}
	{% endif %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_BED_MESH_CALIBRATE_BASE {rawparams}
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	_APPLY_RATOS_BED_MESH_PARAMETERS {rawparams}
	{% endif %}

[gcode_macro SET_GCODE_OFFSET]
rename_existing = SET_GCODE_OFFSET_BASE
gcode = 
	DEBUG_ECHO PREFIX="SET_GCODE_OFFSET" MSG="{rawparams|replace('"', '')|replace("'", '')}"
	{% set z_before = printer.gcode_move.homing_origin.z|float %}
	SET_GCODE_OFFSET_BASE {rawparams}
	_AFTER_SET_GCODE_OFFSET Z_BEFORE={z_before}

[gcode_macro _AFTER_SET_GCODE_OFFSET]
gcode = 
	{% set z_before = params.Z_BEFORE|float %}
	{% set z_after = printer.gcode_move.homing_origin.z|float %}
	{% if z_before != z_after %}
	_ALERT_NON_ZERO_Z_OFFSET FORCE=1
	{% endif %}

[gcode_macro _START_PRINT_PARK]
gcode = 
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_x = printer["gcode_macro RatOS"].start_print_park_x %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% if printer["gcode_macro RatOS"].start_print_park_x is defined and printer["gcode_macro RatOS"].start_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="start_print_park_x is ignored for IDEX printers"
	{% endif %}
	PARK_TOOLHEAD
	G90
	{% endif %}
	
	
	_PARK LOCATION={start_print_park_in} X={start_print_park_x}
	G0 Z{z} F{z_speed}

[gcode_macro _END_PRINT_PARK]
gcode = 
	{% if printer["dual_carriage"] is defined %}
	
	{% if printer["gcode_macro RatOS"].end_print_park_x is defined and printer["gcode_macro RatOS"].end_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="end_print_park_x is ignored for IDEX printers"
	{% endif %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	PARK_TOOLHEAD
	G90
	{% endif %}
	_PARK LOCATION={printer["gcode_macro RatOS"].end_print_park_in} X={printer["gcode_macro RatOS"].end_print_park_x}

[gcode_macro _PARK]
gcode = 
	
	{% set x = params.X %}
	{% set location = params.LOCATION|default('back')|lower %}
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	{% set nozzle_priming = printer["gcode_macro RatOS"].nozzle_priming|lower %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="park"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% if x != '' %}
	{% if x|float >= printer.toolhead.axis_minimum.x + 5 and x|float <= printable_x_max - 5 %}
	{% set park_x = x|float %}
	{% else %}
	{action_respond_info('The requested X co-ordinate is outside the defined axis bounds - using defaults')}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	{% else %}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	
	
	{% set park_y = printable_y_max - 15 %}
	{% if location == 'front' %}
	{% set park_y = printer.toolhead.axis_minimum.y + 5 %}
	{% elif location == 'center' %}
	{% set park_y = printable_y_max / 2 %}
	{% elif location == 'primeblob' and printer["dual_carriage"] is defined %}
	
	{% set park_y = printable_y_max - 15 %}
	{% endif %}
	
	
	{% if location == 'primeblob' and printer["dual_carriage"] is not defined %}
	{% if (nozzle_priming == 'primeblob' or nozzle_priming == 'primeline') %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set park_x = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set park_x = printable_x_max - 5 %}
	{% else %}
	{% set park_x = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set park_y = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set park_y = printable_y_max - 5 %}
	{% else %}
	{% set park_y = nozzle_prime_start_y|float %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	G0 X{park_x} Y{park_y} F{speed}
	{% else %}
	
	G0 Y{park_y} F{speed}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="park"

[gcode_macro SAVE_PROBE_RESULT]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	{% set last_z_offset = 9999.9 %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if beacon_contact_prime_probing %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	{% else %}
	{% set last_z_offset = printer.beacon.last_sample.dist - current_z %}
	{% endif %}
	{% elif printer.fastconfig.settings.bltouch is defined  %}
	{% set config_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% elif printer.fastconfig.settings.probe is defined  %}
	{% set config_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% endif %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Saving offset adjustment of {last_z_offset} in {params.VARIABLE|default('last_z_offset')}"
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={params.VARIABLE|default('last_z_offset')} VALUE={last_z_offset}

[gcode_macro PROBE_FOR_PRIMING]
gcode = 
	
	{% set probe_for_priming_disable_mesh_constraints = true if printer["gcode_macro RatOS"].probe_for_priming_disable_mesh_constraints|default(false)|lower == 'true' else false %}
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower != 'false' %}
	SAVE_GCODE_STATE NAME=probe_for_priming_state
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the prime location.."
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set t = params.TOOLHEAD|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% if idex_mode == '' %}
	
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% if t == 0 %}
	{% set x_start = 5 %}
	{% else %}
	{% set x_start = printable_x_max - 5 %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% endif %}
	{% endif %}
	{% set z = printer.fastconfig.settings.bed_mesh.horizontal_move_z|float %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% if printer.fastconfig.settings.bltouch is defined %}
	{% set x_offset = printer.fastconfig.settings.bltouch.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.bltouch.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% elif printer.fastconfig.settings.probe is defined %}
	{% set x_offset = printer.fastconfig.settings.probe.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.probe.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% elif printer.fastconfig.settings.beacon is defined %}
	{% set x_offset = printer.fastconfig.settings.beacon.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.beacon.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.beacon.trigger_distance|float %}
	{% else %}
	{ action_raise_error("No probe, beacon or bltouch section found. Adaptive priming only works with a [probe], [beacon] or [bltouch] section defined.") }
	{% endif %}
	
	{% if z < z_offset %}
	{ action_raise_error("Horizontal move Z ({z}) is below your probe's Z offset ({z_offset}). Please adjust your horizontal_move_z setting in [bed_mesh] to be above {z}.") }
	{% endif %}
	
	{% if not probe_for_priming_disable_mesh_constraints %}
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float - x_offset %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float - y_offset %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float - x_offset %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float - y_offset %}
	
	
	{% set x_start = [[x_start, max_x]|min, min_x]|max %}
	{% set y_start = [[y_start, max_y]|min, min_y]|max %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the start of the prime location at {x_start}, {y_start}"
	
	G90
	
	M83
	
	G0 Z{z} F{z_speed}
	
	G1 X{x_start} Y{y_start} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result
	{% endif %}
	
	{% if idex_mode == '' %}
	
	{% set x_end = x_start %}
	{% set y_end = y_start + 45 %}
	{% else %}
	
	{% if t==1 %}
	{% set x_end = x_start - 45 %}
	{% else %}
	{% set x_end = x_start + 45 %}
	{% endif %}
	{% set y_end = y_start %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the end of the prime location at {x_end}, {y_end}"
	G1 X{x_end} Y{y_end} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result
	{% endif %}
	
	RESTORE_GCODE_STATE NAME=probe_for_priming_state
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	{% endif %}

[gcode_macro RESET_PRIME_PROBE_STATE]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result VALUE=None
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result_t1 VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result_t1 VALUE=None
	{% endif %}

[gcode_macro PROBE_CURRENT_POSITION]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	SAVE_GCODE_STATE NAME=probe_current_position_state
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	ASSERT_PROBE_DEPLOYED
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_prime_probing %}
	PROBE PROBE_METHOD=contact SAMPLES=1
	{% else %}
	PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	BEACON_QUERY
	{% else %}
	
	RESTORE_GCODE_STATE NAME=probe_current_position_state MOVE=1 MOVE_SPEED={printer["gcode_macro RatOS"].macro_z_speed|float}
	{% endif %}

[gcode_macro PRIME_BLOB]
description = Prints a primeblob, used internally, if configured, as part of the START_PRINT macro.
variable_x_offset = 5
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="prime_blob"
	SET_MACRO_TRAVEL_SETTINGS
	
	RATOS_ECHO PREFIX="Priming" MSG="Priming nozzle with prime blob.."
	
	
	{% set current_toolhead = 0 %}
	
	
	{% set target_idex_mode = '' %}
	{% set extruder = 'extruder' %}
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE is defined %}
	{% set target_idex_mode = params.IDEX_MODE|default('')|lower %}
	{% else %}
	{ action_raise_error("IDEX_MODE parameter not found for PRIME_BLOB macro. This is likely a bug.") }
	{% endif %}
	RATOS_ECHO PREFIX="Priming" MSG="Priming in IDEX {target_idex_mode} mode.."
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set current_toolhead = 1 if current_idex_mode=='primary' else 0 %}
	{% set extruder = 'extruder1' if current_toolhead == 1 else 'extruder' %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	SAVE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set fan_speed = printer["gcode_macro RatOS"].nozzle_prime_bridge_fan|float %}
	{% set nozzle_diameter = printer.fastconfig.settings[extruder].nozzle_diameter|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set has_start_offset_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) != 9999.9 %}
	{% if printer["dual_carriage"] is defined %}
	{% set has_start_offset_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) != 9999.9 %}
	{% endif %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_z_height = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set nozzle_prime_direction = printer["gcode_macro RatOS"].nozzle_prime_direction|lower %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% if target_idex_mode == '' %}
	
	{% set x_factor = 0 %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% set y_factor = -1 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% if nozzle_prime_start_y|float < printable_y_max / 2 %}
	{% set y_factor = 1 %}
	{% else %}
	{% set y_factor = -1 %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_direction == 'forwards' %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_direction == 'backwards' %}
	{% set y_factor = -1 %}
	{% endif %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% else %}
	{% set z = start_print_park_z_height %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% set y_factor = 0 %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set x_start = center_x / 2 + 5 %}
	{% set x_factor = 1 %}
	{% else %}
	
	
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% if current_toolhead == 0 %}
	{% set x_start = 55 %}
	{% set x_factor = -1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 55 %}
	{% set x_factor = 1 %}
	{% endif %}
	{% else %}
	{% if current_toolhead == 0 %}
	{% set x_start = 5 %}
	{% set x_factor = 1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 5 %}
	{% set x_factor = -1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_x_max - 5 %}
	{% endif %}
	{% set z = 10 %}
	{% endif %}
	
	{% set start_z_offset = 0 %}
	{% set end_z_offset = 0 %}
	{% if has_start_offset_t0 %}
	{% set start_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) %}
	{% set end_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_end_result|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t0) ) }
	{% endif %}
	{% if end_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t0) )  }
	{% endif %}
	{% set start_z_offset = start_z_probe_result_t0 %}
	{% set end_z_offset = end_z_probe_result_t0 %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	{% if current_toolhead == 1 or both_toolheads or target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	{% if has_start_offset_t1 %}
	{% set start_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) %}
	{% set end_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_end_result_t1|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t1) ) }
	{% endif %}
	{% if end_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t1) ) }
	{% endif %}
	{% set start_z_offset = [start_z_offset, start_z_probe_result_t1]|max %}
	{% set end_z_offset = [end_z_offset, start_z_probe_result_t1]|max %}
	{% endif %}
	{% endif %}
	{% if target_idex_mode != 'copy' and target_idex_mode != 'mirror' %}
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% set original_start_z_offset = start_z_offset %}
	{% set original_end_z_offset = end_z_offset %}
	{% set start_z_offset = original_end_z_offset %}
	{% set end_z_offset = original_start_z_offset %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	DEBUG_ECHO PREFIX="PRIME_BLOB" MSG="x_start: {x_start}, y_start: {y_start}, x_factor: {x_factor}, y_factor: {y_factor}, z: {z}, start_z_offset: {start_z_offset}, end_z_offset: {end_z_offset}"
	
	
	G90
	
	M83
	RATOS_ECHO PREFIX="Priming" MSG="Lifting Z to {z}.."
	
	G0 Z{z} F{z_speed}
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% if start_print_park_in != 'primeblob' %}
	G1 X{x_start} F{speed}
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% endif %}
	{% else %}
	
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% if target_idex_mode=="copy" or target_idex_mode=="mirror" %}
	RATOS_ECHO PREFIX="Priming" MSG="Mirroring move to {x_start}, {y_start} along the edge of the print area.."
	
	_IDEX_MIRROR PRIMING=1
	{% else %}
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% endif %}
	G1 X{x_start} F{speed}
	{% endif %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Starting prime blob.."
	
	G1 Z{0.5 + start_z_offset} F{z_speed}
	
	G1 Y{y_start} F{speed}
	
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	
	M106 S{fan_speed}
	
	G1 Z5 F100 E5
	G92 E0
	RATOS_ECHO PREFIX="Priming" MSG="Bridging with {((fan_speed/255) * 100)|int}% fan speed.."
	
	G1 F3000 X{x_start + (15 * x_factor)} Y{y_start + (15 * y_factor)} E{1 / ((0.4 / nozzle_diameter) ** 2)}
	
	
	
	G1 F3000 X{x_start + (20 * x_factor)} Y{y_start + (20 * y_factor)} Z{3.8 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (34 * x_factor)} Y{y_start + (34 * y_factor)} Z{2.6 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (38 * x_factor)} Y{y_start + (38 * y_factor)} Z{1.4 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (42 * x_factor)} Y{y_start + (42 * y_factor)} Z{0.2 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	
	M106 S0
	
	G1 F3000 X{x_start + (46 * x_factor)} Y{y_start + (46 * y_factor)} Z{0.2 + end_z_offset} E0.6
	
	G1 F{speed} X{x_start + (50 * x_factor)} Y{y_start + (50 * y_factor)}
	
	
	{% if target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if target_idex_mode == "copy" %}
	{% if first_y >= 0 %}
	_IDEX_COPY DANCE=0 Y={first_y}
	{% else %}
	_IDEX_COPY DANCE=0 Y={params.Y1}
	{% endif %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	RESTORE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="prime_blob"
	
	
	G92 E0

[gcode_macro UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set temp = params.TEMP|default(220)|int %}
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_UNLOAD_FILAMENT TEMP={temp} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_UNLOAD_FILAMENT]
description = Unload filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_UNLOAD_FILAMENT" MSG="TEMP: {temp}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=unload_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	G4 P3000
	
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD=0 NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=unload_state
	
	
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament unloading completed"

[gcode_macro _IDEX_UNLOAD_FILAMENT]
description = Unload filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading T{toolhead} filament..."
	
	DEBUG_ECHO PREFIX="_IDEX_UNLOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} AUTOMATED={automated}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="T{toolhead} filament unloading completed"

[gcode_macro _UNLOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LEGACY_UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
gcode = 
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set unload_speed = 5 * 60 %}
	{% set unload_length = printer["gcode_macro RatOS"].filament_unload_length|float %}
	M117 Unloading filament...
	
	G0 E10 F300
	
	G0 E-5 F3600
	
	G4 P3000
	
	G0 E5 F6000
	
	G0 E-15 F6000
	
	G0 E-{unload_length} F{unload_speed}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}
	M117 Filament unloaded!
	RESPOND MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	RATOS_ECHO MSG="Unloading filament from nozzle to cooling zone... Please wait!"
	
	_PURGE_BEFORE_UNLOAD TOOLHEAD={toolhead}
	
	{% if printer["gcode_macro _UNLOAD_WITHOUT_TIP_FORMING"] is defined %}
	
	_UNLOAD_WITHOUT_TIP_FORMING TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	_UNLOAD_WITH_TIP_FORMING NAME='{filament_name}' TYPE='{filament_type}'
	{% endif %}
	
	G4 P3000

[gcode_macro _UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	{% set tooolhead_sensor_to_extruder_gear_distance = printer["gcode_macro T%s" % toolhead].tooolhead_sensor_to_extruder_gear_distance|float %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER" MSG="TOOLHEAD: {toolhead}"
	
	
	G0 E-{extruder_gear_to_cooling_position_distance + tooolhead_sensor_to_extruder_gear_distance + 50} F{extruder_load_speed}
	
	RATOS_ECHO MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_WITH_TIP_FORMING]
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	{% if filament_name != '' and filament_type != '' %}
	_UNLOAD_KNOWN_FILAMENT NAME={filament_name} TYPE={filament_type}
	{% else %}
	_UNLOAD_UNKNOWN_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _UNLOAD_KNOWN_FILAMENT]
description = User overrideable tip forming macro if slicer filament profiles are known
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	RATOS_ECHO PREFIX="FILAMENT TYPE" MSG='{filament_type}'
	RATOS_ECHO PREFIX="FILAMENT PROFILE" MSG='{filament_name}'
	
	
	{% if filament_name == "Prusament PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% elif filament_name == "Nobufil PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% else %}
	
	RATOS_ECHO PREFIX="_UNLOAD_KNOWN_FILAMENT" MSG="Filament profile not found!"
	_UNLOAD_UNKNOWN_FILAMENT
	{% endif %}

[gcode_macro _UNLOAD_UNKNOWN_FILAMENT]
description = User overrideable standard tip forming macro
gcode = 
	
	DEBUG_ECHO PREFIX="_UNLOAD_UNKNOWN_FILAMENT" MSG="Using standard tip forming macro!"
	
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10

[gcode_macro _TIP_FORMING]
gcode = 
	
	{% set cooling_moves = params.COOLING_MOVES|default(4)|int %}
	{% set cooling_move_length = params.COOLING_MOVE_LENGTH|default(10)|float %}
	{% set start_cooling_speed = params.START_COOLING_SPEED|default(10)|float * 60 %}
	{% set end_cooling_speed = params.END_COOLING_SPEED|default(50)|float * 60 %}
	{% if cooling_moves == 0 %}
	{% set cooling_move_length = 0 %}
	{% endif %}
	
	
	{% set dip = true if params.DIP|default(false)|lower == "true" else false %}
	{% set dip_length = params.DIP_LENGTH|default(22)|float %}
	{% set dip_speed = params.DIP_SPEED|default(30)|float * 60 %}
	{% set dip_retract_speed = params.DIP_RETRACT_SPEED|default(70)|float * 60 %}
	
	
	{% set retract_length = params.RETRACT_LENGTH|default(18)|float %}
	{% set start_retract_speed = params.START_RETRACT_SPEED|default(120)|float * 60 %}
	{% set end_retract_speed = params.END_RETRACT_SPEED|default(20)|float * 60 %}
	
	DEBUG_ECHO PREFIX="_TIP_FORMING" MSG="cooling_moves: {cooling_moves}, cooling_move_length: {cooling_move_length}, start_cooling_speed: {start_cooling_speed}, end_cooling_speed: {end_cooling_speed}, dip: {dip}, dip_length: {dip_length}, dip_speed: {dip_speed}, dip_retract_speed: {dip_retract_speed}, retract_length: {retract_length}, start_retract_speed: {start_retract_speed}, end_retract_speed: {end_retract_speed}"
	
	M220 S100
	
	
	G92 E0
	{% set retract = retract_length + cooling_move_length / 2 - 15 %}
	G1 E-15 F{start_retract_speed}
	G1 E-{0.7 * retract} F{1.0 * end_retract_speed}
	G1 E-{0.2 * retract} F{0.5 * end_retract_speed}
	G1 E-{0.1 * retract} F{0.3 * end_retract_speed}
	
	
	G92 E0
	{% if cooling_moves > 0 %}
	{% set i = (end_cooling_speed - start_cooling_speed) / (2 * cooling_moves - 1) %}
	{% for m in range(cooling_moves) %}
	G1 E{cooling_move_length} F{(start_cooling_speed + i * m * 2)}
	G1 E-{cooling_move_length} F{(start_cooling_speed + i * (m * 2 + 1))}
	{% endfor %}
	{% endif %}
	
	
	G92 E0
	{% if dip %}
	G1 E{dip_length} F{dip_speed}
	G4 P100
	G1 E-{dip_length} F{dip_retract_speed}
	{% endif %}
	
	G92 E0
	M400

[delayed_gcode __ON_FILAMENT_SENSOR_BUTTON_PRESSED_STARTUP_GUARD]
initial_duration = 2.
gcode = 
	SET_GCODE_VARIABLE MACRO=_ON_FILAMENT_SENSOR_BUTTON_PRESSED VARIABLE=startup_complete VALUE=True

[gcode_macro _ON_FILAMENT_SENSOR_BUTTON_PRESSED]
variable_startup_complete = False
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set toolhead_sensor_button_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_sensor_button_only_when_sensor_enabled|default(false)|lower == 'true' %}
	
	
	{% if not startup_complete and sensor_enabled %}
	{action_emergency_stop("RatOS: The T%s filament sensor button was triggered immediately on printer startup. This is likely a false trigger. Please check your filament sensor wiring and configuration!" % (toolhead,))}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_SENSOR_BUTTON_PRESSED" MSG="TOOLHEAD: {toolhead}, SENSOR_ENABLED: {sensor_enabled}, TOOLHEAD_SENSOR_BUTTON_ONLY_WHEN_SENSOR_ENABLED: {toolhead_sensor_button_only_when_sensor_enabled}"
	
	{% if not printer.virtual_sdcard.is_active and (sensor_enabled or not toolhead_sensor_button_only_when_sensor_enabled) %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	{% set toolhead_detect_clog_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_detect_clog_only_when_sensor_enabled|default(true)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}, ENABLE_CLOG_DETECTION: {enable_clog_detection}, TOOLHEAD_DETECT_CLOG_ONLY_WHEN_SENSOR_ENABLED: {toolhead_detect_clog_only_when_sensor_enabled}, SENSOR_ENABLED: {sensor_enabled}"
	
	{% if enable_clog_detection and (sensor_enabled or not toolhead_detect_clog_only_when_sensor_enabled) %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_clog_detection %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_FILAMENT_END]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set clogged = true if params.CLOGGED|default(false)|lower == 'true' else false %}
	
	
	{% set unload_after_runout = printer["gcode_macro T%s" % toolhead].unload_after_runout|float %}
	
	
	{% if clogged %}
	_LED_FILAMENT_CLOG TOOLHEAD={toolhead}
	{% else %}
	_LED_FILAMENT_RUNOUT TOOLHEAD={toolhead}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_END" MSG="TOOLHEAD: {toolhead}"
	
	{% if printer.virtual_sdcard.is_active %}
	{% if not printer.pause_resume.is_paused %}
	PAUSE RUNOUT=True
	{% endif %}
	{% if not clogged and unload_after_runout %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	{% if not clogged and printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true'%}
	_JOIN_SPOOL TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M600]
description = Executes a color change by pausing the printer an unloading the filament.
gcode = 
	PAUSE
	UNLOAD_FILAMENT AUTOMATED=True
	RATOS_ECHO MSG="Please load new filament and resume"

[gcode_macro COLD_PULL]
description = Automated hotend cold pull.
gcode = 
	
	{% set extrusion_temp = params.EXTRUSION_TEMP|default(220)|int %}
	{% set cold_pull_temp = params.COLD_PULL_TEMP|default(80)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	
	{% if printer["dual_carriage"] is not defined %}
	{% set toolhead = 0 %}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead != 0 and toolhead != 1 %}
	{action_raise_error("Please select toolhead! 0 = left, 1 = right toolhead")}
	{% endif %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	RATOS_ECHO MSG="Starting cold pull on T{toolhead}..."
	{% else %}
	RATOS_ECHO MSG="Starting cold pull..."
	{% endif %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	SAVE_GCODE_STATE NAME=cold_pull_state
	
	
	{% if printer["dual_carriage"] is defined and "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	RATOS_ECHO MSG="Heating T{toolhead} to {extrusion_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={extrusion_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={extrusion_temp} MAXIMUM={extrusion_temp + 2}
	
	
	G4 P3000
	
	
	RATOS_ECHO MSG="extruding..."
	G92 E0
	G1 E30 F300
	G92 E0
	
	
	RATOS_ECHO MSG="Cooling T{toolhead} to {cold_pull_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={cold_pull_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={cold_pull_temp} MAXIMUM={cold_pull_temp + 2}
	
	
	G4 P10000
	
	
	RATOS_ECHO MSG="cold pull..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-40 VELOCITY=5 ACCEL=100
	
	
	RATOS_ECHO MSG="eject filament..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-200 VELOCITY=20 ACCEL=500
	
	
	RATOS_ECHO MSG="cooling down extruder..."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	RESTORE_GCODE_STATE NAME=cold_pull_state
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	
	CONSOLE_ECHO TITLE="Cold pull complete" MSG="Please remove the filament from the PTFE tube and cut the end off. Do NOT try to load it again." TYPE="warning"

[gcode_macro _USER_START_PRINT_BEFORE_HOMING]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_BED]
gcode = 

[gcode_macro _USER_START_PRINT_BED_MESH]
gcode = 

[gcode_macro _USER_START_PRINT_PARK]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 

[gcode_macro _USER_START_PRINT_HEAT_CHAMBER]
description = Uses the extruder sensor to wait for chamber temp. Override the _START_PRINT_HEAT_CHAMBER macro to implement heated chamber handling.
gcode = 
	
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}

[gcode_macro _USER_END_PRINT_BEFORE_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_AFTER_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_PARK]
gcode = 

[gcode_macro _USER_END_PRINT_FINISHED]
description = User hook for when the print is finished after gcode state has been restored.
gcode = 

[gcode_macro _USER_START_PRINT]
gcode = 

[gcode_macro _USER_END_START_PRINT]
gcode = 

[gcode_macro _USER_START_FEATURE]
gcode = 

[gcode_macro _USER_END_FEATURE]
gcode = 

[gcode_macro _USER_BEFORE_IDLE_TIMEOUT]
gcode = 

[gcode_macro _USER_AFTER_IDLE_TIMEOUT]
gcode = 

[gcode_macro ECHO_T_VARS]
description = Echo Toolhead variables to the console.
gcode = 
	{% set t = params.T|default(0) %}
	RATOS_ECHO MSG="T{t} Variables"
	{% for var, value in printer["gcode_macro T%s" % t].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ECHO_RATOS_VARS]
description = Echo RatOS variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro RatOS"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ENSURE_CRITICAL_RATOS_INIT]
variable_completed = False
gcode = 
	{% if not completed %}
	CALCULATE_PRINTABLE_AREA
	SET_GCODE_VARIABLE MACRO=ENSURE_CRITICAL_RATOS_INIT VARIABLE=completed VALUE=True
	{% endif %}

[delayed_gcode RATOS_INIT]
initial_duration = 0.1
gcode = 
	{action_respond_info("Initializing RatOS...")}
	ENSURE_CRITICAL_RATOS_INIT
	_LED_STANDBY
	INITIAL_FRONTEND_UPDATE
	_CHAMBER_FILTER_SANITY_CHECK
	{% if printer.fastconfig.settings.beacon is defined %}
	
	_BED_MESH_SANITY_CHECK
	{% endif %}
	{% set svv = printer.save_variables.variables %}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=0 C={svv.nozzle_expansion_coefficient_t0|default(0.06)|float}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=1 C={svv.nozzle_expansion_coefficient_t1|default(0.06)|float}
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=idex_applied_offset

[delayed_gcode RATOS_LOGO]
initial_duration = 2
gcode = 
	
	
	
	
	
	ENSURE_CRITICAL_RATOS_INIT
	HELLO_RATOS
	_ALERT_NON_ZERO_Z_OFFSET

[gcode_macro _ALERT_NON_ZERO_Z_OFFSET]
gcode = 
	{% set force = params.FORCE|default(0)|int == 1 %}
	{% set user_offset = printer.named_offsets.user_probe_z_offset.z|float %}
	{% set gcode_offset = printer.gcode_move.homing_origin.z|float %}
	{% set combined_offset = user_offset + gcode_offset %}
	
	{% if force or user_offset != 0 or gcode_offset != 0 %}
	{% set title = "User-adjusted Z-offset of %.3f mm is active" % combined_offset %}
	{% set msg = "" %}
	{% set nl = "" %}
	{% if user_offset != 0 %}
	{% set msg = msg + "beacon true zero user Z-offset: %.3f mm (to clear, use Z_OFFSET_APPLY_PROBE CLEAR=1)" % user_offset %}
	{% set nl = "_N_" %}
	{% endif %}
	{% if gcode_offset != 0 %}
	{% set msg = msg + nl + "G-code Z-offset: %.3f mm" % gcode_offset %}
	{% endif %}
	CONSOLE_ECHO TITLE="{title}" TYPE="info" MSG="{msg}"
	{% endif %}

[gcode_macro _INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE]
gcode = 
	{% set variable = params.VARIABLE|string %}
	{% set svv = printer.save_variables.variables %}
	{% set nlu_msg = "no longer used, please remove" %}
	{% if svv[variable] is defined %}
	{% set v = svv[variable]|string|replace('"', '')|replace("'", "") %}
	{% if not nlu_msg in v %}
	SAVE_VARIABLE VARIABLE={variable} VALUE='"{nlu_msg} (was {v})"'
	{% endif %}
	CONSOLE_ECHO TITLE="Deprecated ratos-variables.cfg variable" TYPE="warning" MSG="The variable {variable} is no longer used, please remove it from your ratos-variables.cfg file."
	{% endif %}

[gcode_macro _NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK]
gcode = 
	
	
	
	
	
	
	
	{% set t = params.T|int %}
	{% set c = params.C|float %}
	{% set normal_low = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_low|default(0.05)|float %}
	{% set normal_high = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_high|default(0.10)|float %}
	
	{% if c < 0 %}
	
	{action_emergency_stop("Invalid nozzle_expansion_coefficient_t%s value in ratos-variables.cfg: %.3f. It must be non-negative." % (t, c))}
	{% endif %}
	{% if c >= normal_high %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite high. Please verify that this is correct."
	{% endif %}
	{% if c <= normal_low %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite low. Please verify that this is correct."
	{% endif %}

[gcode_macro INITIAL_FRONTEND_UPDATE]
gcode = 
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_error = printer["gcode_macro RatOS"].status_color_error|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_unknown}"'
	{% endif %}
	
	
	{% set t0_sensor = "undefined" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	{% set t0_sensor = "detected" %}
	{% else %}
	{% set t0_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t0_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	{% set t1_sensor = "undefined" %}
	{% if printer["dual_carriage"] is defined and printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	{% set t1_sensor = "detected" %}
	{% else %}
	{% set t1_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t1_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	{% if svv.t0_filament is defined and printer["gcode_macro T0"] is defined %}
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	{% if t0_sensor != "empty" %}
	{% set t0_filament_type = svv.t0_filament[0]|default('')|string %}
	{% set t0_filament_name = svv.t0_filament[1]|default('')|string %}
	{% set t0_filament_temp = svv.t0_filament[2]|default(0)|float %}
	{% if t0_filament_name != '' and t0_filament_type != '' and t0_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{t0_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{t0_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={t0_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}
	{% if svv.t1_filament is defined and printer["gcode_macro T1"] is defined %}
	{% if printer["gcode_macro T1"].filament_name is defined and printer["gcode_macro T1"].filament_type is defined and printer["gcode_macro T1"].filament_temp is defined %}
	{% if t1_sensor != "empty" %}
	{% set t1_filament_type = svv.t1_filament[0]|default('')|string %}
	{% set t1_filament_name = svv.t1_filament[1]|default('')|string %}
	{% set t1_filament_temp = svv.t1_filament[2]|default(0)|float %}
	{% if t1_filament_name != '' and t1_filament_type != '' and t1_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='"{t1_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='"{t1_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE={t1_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t1_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro CALCULATE_PRINTABLE_AREA]
variable_calculated = False
gcode = 
	{% if not calculated %}
	{% set bed_margin_x = printer["gcode_macro RatOS"].bed_margin_x %}
	{% set bed_margin_y = printer["gcode_macro RatOS"].bed_margin_y %}
	
	
	
	{% set tool = 0 if printer["gcode_macro T0"] is not defined or printer["gcode_macro T0"].active else 1 %}
	{% set max_x = printer.toolhead.axis_maximum.x if printer["dual_carriage"] is defined and tool == 0 else printer.toolhead.axis_maximum.x - bed_margin_x[1] %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	
	
	{% set max_x = printer.toolhead.axis_maximum.x %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="printer.toolhead.axis_maximum.x {printer.toolhead.axis_maximum.x}"
	
	{% set max_y = printer.toolhead.axis_maximum.y - bed_margin_y[1]%}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_x_max VALUE={max_x}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_y_max VALUE={max_y}
	SET_GCODE_VARIABLE MACRO=CALCULATE_PRINTABLE_AREA VARIABLE=calculated VALUE=True
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	RATOS_LOG PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	{% endif %}

[gcode_macro CACHE_TOOLHEAD_SETTINGS]
variable_cache = {"global": {"accel": 1000, "ratio": 0.5, "speed": 50, "scv": 5}}
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set dummy = cache.__setitem__(key, {"accel": printer.toolhead.max_accel, "ratio": printer.toolhead.minimum_cruise_ratio, "speed": printer.toolhead.max_velocity, "scv": printer.toolhead.square_corner_velocity}) %}
	SET_GCODE_VARIABLE MACRO=CACHE_TOOLHEAD_SETTINGS VARIABLE=cache VALUE="{cache | pprint | replace("\n", "") | replace("\"", "\\\"")}"
	DEBUG_ECHO PREFIX="CACHE_TOOLHEAD_SETTINGS" MSG="Toolhead settings cached for {key}. {printer.toolhead.max_accel} accel, {printer.toolhead.minimum_cruise_ratio} ratio, {printer.toolhead.max_velocity} velocity, {printer.toolhead.square_corner_velocity} scv."

[gcode_macro RESTORE_TOOLHEAD_SETTINGS]
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set values = printer["gcode_macro CACHE_TOOLHEAD_SETTINGS"].cache.__getitem__(key) %}
	{% if values is not defined or values == 'None' %}
	{ action_raise_error("RESTORE_TOOLHEAD_SETTINGS: Toolhead settings not cached for key '" ~ key ~ "'.") }
	{% endif %}
	SET_VELOCITY_LIMIT ACCEL={values.accel} MINIMUM_CRUISE_RATIO={values.ratio} VELOCITY={values.speed} SQUARE_CORNER_VELOCITY={values.scv}
	DEBUG_ECHO PREFIX="RESTORE_TOOLHEAD_SETTINGS" MSG="Toolhead settings restored. {values.accel} accel, {values.ratio} ratio, {values.speed} velocity, {values.scv} scv."

[gcode_macro SET_MACRO_TRAVEL_SETTINGS]
gcode = 
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float %}
	{% set accel = printer["gcode_macro RatOS"].macro_travel_accel %}
	SET_VELOCITY_LIMIT ACCEL={accel} MINIMUM_CRUISE_RATIO=0.5 VELOCITY={speed} SQUARE_CORNER_VELOCITY={5}
	DEBUG_ECHO PREFIX="SET_MACRO_TRAVEL_SETTINGS" MSG="Macro travel settings set. {accel} accel, {speed} velocity"

[gcode_macro SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% if printer["dual_carriage"] is not defined %}
	
	SET_KINEMATIC_POSITION X={printable_x_max / 2} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	{% else %}
	
	IDEX_SET_CENTER_KINEMATIC_POSITION
	{% endif %}

[gcode_macro IDEX_SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x - (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x + (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY

[gcode_macro VERIFY_HYBRID_INVERTED]
gcode = 
	
	{% set inverted = False %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy is defined and printer.fastconfig.settings.ratos_hybrid_corexy.inverted is defined %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy.inverted|lower == 'true' %}
	{% set inverted = True %}
	{% endif %}
	{% endif %}
	{% if inverted == False %}
	{ action_emergency_stop("ratos_hybrid_corexy NOT INVERTED! Inverted hybrid core-xy bugfix not detected.") }
	{% endif %}

[gcode_macro RATOS_ECHO]
gcode = 
	{% set prefix = "RatOS" %}
	{% set debug = params.DEBUG|default(0)|int %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " | " ~ params.PREFIX %}
	{% endif %}
	{% set prefix = prefix ~ ":" %}
	{% set msg = "" %}
	{% if params.MSG is defined %}
	{% set msg = params.MSG %}
	{% else %}
	{% set msg = "No msg parameter provided (this is a bug or unintended use)." %}
	{% endif %}
	{% if not debug %}
	
	M117 {prefix} {msg}
	{% endif %}
	RATOS_LOG PREFIX="{prefix}" MSG="{msg}"
	{% if not debug %}
	RESPOND PREFIX="{prefix}" MSG="{msg}"
	{% else %}
	CONSOLE_ECHO TITLE="{prefix}" TYPE="debug" MSG="{msg}"
	{% endif %}

[gcode_macro ENABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=True
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=prefix_filter VALUE="'{params.FILTER|default('')|lower}'"
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging enabled."

[gcode_macro DISABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=False
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging disabled."

[gcode_macro DEBUG_ECHO]
variable_enabled = False
variable_prefix_filter = ''
gcode = 
	{% set prefix = "DEBUG" %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " - " ~ params.PREFIX %}
	{% endif %}
	{% if enabled and (prefix_filter|lower == '' or prefix_filter|lower in params.PREFIX|lower) %}
	RATOS_ECHO PREFIX="{prefix}" MSG="{params.MSG}" DEBUG=1
	{% endif %}

[gcode_macro START_FEATURE]
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="Start {params.FEATURE} feature gcode"
	{% set scv = printer.toolhead.square_corner_velocity|int|default(5) %}
	{% set accel = printer.toolhead.max_accel|int|default(10000) %}
	{% set ratio = printer.toolhead.minimum_cruise_ratio|float|default(0.5) %}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="scv" VALUE={scv}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="accel" VALUE={accel}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="ratio" VALUE={ratio}
	_USER_START_FEATURE FEATURE="{params.FEATURE}"

[gcode_macro END_FEATURE]
variable_scv = 5
variable_accel = 10000
variable_ratio = 0.5
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="End {params.FEATURE} feature gcode"
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={scv} ACCEL={accel} MINIMUM_CRUISE_RATIO={ratio}
	_USER_END_FEATURE FEATURE="{params.FEATURE}" SCV={scv} ACCEL={accel} RATIO={ratio}

[gcode_macro _ON_LAYER_CHANGE]
variable_layer_number = 0
description = INTERNAL USE ONLY. Call it from the slicers after layer change custom gcode
gcode = 
	
	{% set layer = params.LAYER|int %}
	
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE={layer}
	SET_PRINT_STATS_INFO CURRENT_LAYER={layer}

[gcode_macro _LEARN_MORE_CALIBRATION]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/calibration" %}
	{% set link_text = "RatOS Calibration Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_CHAMBER_FILTER]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter Control" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_FILAMENT]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/filaments" %}
	{% set link_text = "RatOS Filament Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _CONSOLE_SAVE_CONFIG]
gcode = 
	M118 Click <a class="command text--blue">SAVE_CONFIG</a> to save the settings to your printer.cfg.

[gcode_macro _LOAD_RATOS_SKEW_PROFILE]
gcode = 
	{% set ratos_skew_profile = printer["gcode_macro RatOS"].skew_profile|default("") %}
	{% if ratos_skew_profile != "" %}
	{% if printer.fastconfig.config["skew_correction %s" % ratos_skew_profile] is defined %}
	SKEW_PROFILE LOAD={ratos_skew_profile}
	GET_CURRENT_SKEW
	{% else %}
	{% set line_1 = '"Could not find skew profile %s!_N_Clearing skew correction."' % ratos_skew_profile %}
	CONSOLE_ECHO TITLE="Missing skew profile!" TYPE="warning" MSG={line_1}
	SET_SKEW CLEAR=1
	{% endif %}
	{% endif %}

[gcode_macro M601]
gcode = 
	PAUSE

[gcode_macro _STOP_AND_RAISE_ERROR]
gcode = 
	M84
	_RAISE_ERROR MSG="{params.MSG}"

[gcode_macro _RESET_GCODE_VARIABLES]
description = Reset specified [gcode_macro ...] variables to their original values from configuration when Klipper started.
	- MACRO: Name of the GCODE macro containing the variables to reset.
	- VARIABLES: Comma-separated list of variable names to reset (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- QUIET: (optional) If true, suppresses console echo messages for each reset variable. Default is false.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set quiet = params.QUIET|default("false")|lower in ("true", "1", "yes") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	{% set settings = printer.fastconfig.settings[obj_name|lower] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro %s]" % macro) }
	{% endif %}
	
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if settings["variable_%s" % var] is not defined %}
	{ action_raise_error("Variable '%s' is not defined in settings for [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	
	{% for var in vars %}
	{% set var_value = obj[var] %}
	{% if var_value is defined %}
	{% set v = settings["variable_%s" % var] %}
	{% if v != var_value|string %}
	{% if var_value is string %}
	{% set v = '"\'' ~ v|replace('"', '\\"')|replace("'", "\\'") ~ '\'"' %}
	{% endif %}
	SET_GCODE_VARIABLE MACRO={macro} VARIABLE={var} VALUE={v}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Reset {macro} variable {var} to original value: {v} (was {obj[var]})"
	{% endif %}
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro _SHOW_GCODE_VARIABLES]
description = Show current values of specified [gcode_macro ...] variables.
	- MACRO: Name of the GCODE macro containing the variables to show.
	- VARIABLES: Comma-separated list of variable names to show (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- PAD: (optional) If defined, provide a single character to use for padding variable names to align values in a tabular format in the console output. Default is no padding.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set pad = params.PAD|default("") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	
	{% set ns = namespace() %}
	{% set ns.max_len = 0 %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% set ns.max_len = (ns.max_len, var|length)|max %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if pad %}
	{% set padding = pad * (ns.max_len - var|length) %}
	CONSOLE_ECHO MSG="{var}{padding} {obj[var]}"
	{% else %}
	CONSOLE_ECHO MSG="{var}: {obj[var]}"
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro PAUSE]
description = Pauses the print
rename_existing = PAUSE_BASE
variable_extrude = 1.5
variable_retract = 1.5
variable_fan_speed = 0
variable_idex_mode = ""
variable_idex_toolhead = 0
variable_idex_toolhead_x = 0.0
variable_idex_toolhead_y = 0.0
variable_idex_toolhead_z = 0.0
gcode = 
	RATOS_ECHO MSG="Pausing print..."
	
	
	{% set runout_detected = true if params.RUNOUT|default(false)|lower == 'true' else false %}
	
	
	_LED_PAUSE
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	SAVE_GCODE_STATE NAME=PAUSE_state
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_mode VALUE='"{idex_mode}"'
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={idex_toolhead}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_x VALUE={printer.gcode_move.gcode_position.x|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_y VALUE={printer.gcode_move.gcode_position.y|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_z VALUE={printer.gcode_move.gcode_position.z|float}
	DEBUG_ECHO PREFIX="PAUSE" MSG="idex_mode: {idex_mode}, idex_toolhead: {idex_toolhead}, idex_toolhead_x: {idex_toolhead_x}, idex_toolhead_y: {idex_toolhead_y}, idex_toolhead_z: {idex_toolhead_z}"
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="pause"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if current_z < (max_z - 20.0) %}
	{% set z_safe = 20.0 %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	PAUSE_BASE
	
	
	{% if printer["dual_carriage"] is not defined %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan"].speed|float}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	{% if idex_toolhead == 0 %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t1"].speed|float}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106 S0
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set R = printer["gcode_macro PAUSE"].retract|float %}
	{% if can_extrude %}
	G91
	G1 E-{R} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	{% set pause_print_park_x = printer["gcode_macro RatOS"].pause_print_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].pause_print_park_in %}
	{% if runout_detected %}
	{% set pause_print_park_x = printer["gcode_macro RatOS"].runout_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].runout_park_in %}
	{% endif %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	DEBUG_ECHO PREFIX="PAUSE" MSG="z_speed: {z_speed}, pause_print_park_x: {pause_print_park_x}, pause_print_park_in: {pause_print_park_in}, default_toolhead: {default_toolhead}"
	{% if "xyz" in printer.toolhead.homed_axes %}
	G91
	G1 Z{z_safe} F{z_speed}
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% else %}
	
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	_IDEX_SINGLE X={parking_position}
	{% else %}
	PARK_TOOLHEAD
	{% endif %}
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="pause"
	
	RATOS_ECHO MSG="Print paused"

[gcode_macro RESUME]
description = Resumes the print if the printer is paused.
rename_existing = RESUME_BASE
gcode = 
	
	
	RATOS_ECHO MSG="Resuming print..."
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	
	{% set target_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set target_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if target_idex_mode != '' %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set fan_speed = printer["gcode_macro PAUSE"].fan_speed|float %}
	{% if printer["dual_carriage"] is not defined %}
	M106 S{(fan_speed * 255)}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% else %}
	{% if params.TOOLHEAD is defined %}
	
	{% if params.TOOLHEAD == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% else %}
	{% if printer["gcode_macro PAUSE"].idex_toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	{% if params.TOOLHEAD is defined %}
	_SELECT_TOOL T={params.TOOLHEAD} X=-1 Y=-1 TOOLSHIFT=false
	{% else %}
	_SELECT_TOOL T={printer["gcode_macro PAUSE"].idex_toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	{% endif %}
	
	{% set x = printer["gcode_macro PAUSE"].idex_toolhead_x|float %}
	{% set y = printer["gcode_macro PAUSE"].idex_toolhead_y|float %}
	{% set z = printer["gcode_macro PAUSE"].idex_toolhead_z|float %}
	G1 X{x} Y{y} Z{z} F{speed}
	{% if params.TOOLHEAD is defined %}
	
	SAVE_GCODE_STATE NAME=PAUSE_STATE
	{% endif %}
	{% endif %}
	
	
	{% if params.TOOLHEAD is not defined %}
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% if can_extrude %}
	G91
	G1 E{E} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1 MOVE_SPEED={speed}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	RESUME_BASE
	
	
	_LED_PRINTING
	
	RATOS_ECHO MSG="Print resumed"

[gcode_macro CANCEL_PRINT]
description = Cancels the print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	RATOS_ECHO MSG="Cancelling print..."
	END_PRINT
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	
	CANCEL_PRINT_BASE
	RATOS_ECHO MSG="Print cancelled"

[gcode_macro START_PRINT]
description = Start print procedure, use this in your Slicer.
variable_post_processor_version = 2
variable_is_printing_gcode = False
variable_both_toolheads = True
variable_object_xoffset = 0
variable_first_x = -1
variable_first_y = -1
variable_total_toolshifts = 0
variable_initial_tool = 0
variable_extruder_first_layer_temp = ""
variable_extruder_other_layer_temp = ""
gcode = 
	
	{% if params.EXTRUDER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_TEMP parameter not found.")}
	{% endif %}
	{% if params.EXTRUDER_OTHER_LAYER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_OTHER_LAYER_TEMP parameter not found.")}
	{% endif %}
	{% if params.BED_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. BED_TEMP parameter not found.")}
	{% endif %}
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' and printer["gcode_macro RatOS"].danger_force_allow_auto_center_subject|default(false)|lower != 'true'%}
	
	
	
	
	
	{ action_raise_error("The experimental auto_center_subject feature is not supported in this version of RatOS. Please disable it in the RatOS macro settings.") }
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes and printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% if printer["gcode_macro _VAOC"].is_started|default(true)|lower == 'true' %}
	_VAOC_END
	{% endif %}
	{% endif %}
	
	
	_LED_START_PRINTING
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_USER_START_PRINT { rawparams }
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_probe_stowable = printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% endif %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	{% set X0 = params.X0|default(-1)|float %}
	{% set X1 = params.X1|default(-1)|float %}
	{% set Y0 = params.Y0|default(-1)|float %}
	{% set Y1 = params.Y1|default(-1)|float %}
	{% if first_x == -1 or first_y == -1 %}
	{% set first_x = params.FIRST_X|default(-1)|float %}
	{% set first_y = params.FIRST_Y|default(-1)|float %}
	{% endif %}
	{% set total_toolshifts = params.TOTAL_TOOLSHIFTS|default(0)|int %}
	{% set initial_tool = params.INITIAL_TOOL|default(default_toolhead)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	
	
	
	
	
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(printer.heater_bed.target, true)|float %}
	
	
	{% set total_layer_count = params.TOTAL_LAYER_COUNT|default(0)|int %}
	{% set extruder_first_layer_temp = (params.EXTRUDER_TEMP|default("")).split(",") %}
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL BEACON_CONTACT_START_PRINT_TRUE_ZERO={beacon_contact_start_print_true_zero} BEACON_CONTACT_CALIBRATE_MODEL_ON_TRUE_ZERO={beacon_contact_calibrate_model_on_true_zero}
	{% endif %}
	
	_START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH BED_TEMP={bed_temp}
	
	
	RATOS_ECHO MSG="First print coordinates X:{first_x} Y:{first_y}"
	
	
	{% if params.TOTAL_LAYER_COUNT is not defined %}
	{% set link_url = "https://os.ratrig.com/docs/slicers" %}
	{% set link_text = "RatOS Slicer Configuration" %}
	{% set line_1 = '"Your slicer gcode settings are not up to date._N_Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="Incomplete Slicer Configuration detected" TYPE="warning" MSG={line_1}
	{% endif %}
	
	
	SET_PRINT_STATS_INFO CURRENT_LAYER=1
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE=1
	{% if total_layer_count > 0 %}
	SET_PRINT_STATS_INFO TOTAL_LAYER={total_layer_count}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads %}
	{% set initial_tool = 0 if initial_tool == 1 else 1 %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	{% endif %}
	
	
	{% set both_toolheads = true %}
	{% if total_toolshifts == 0 %}
	{% set both_toolheads = false %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	{% endif %}
	{% if both_toolheads and (idex_mode == "copy" or idex_mode == "mirror") %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Gcode tool changes found. Copy and mirror mode do not support toolchanges.")}
	{% endif %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set both_toolheads = true %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=initial_tool VALUE={initial_tool}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_x VALUE={first_x}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_y VALUE={first_y}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=total_toolshifts VALUE={total_toolshifts}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=both_toolheads VALUE={both_toolheads}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_first_layer_temp VALUE="'{params.EXTRUDER_TEMP}'"
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_other_layer_temp VALUE="'{params.EXTRUDER_OTHER_LAYER_TEMP}'"
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE=0
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set svv = printer.save_variables.variables %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set stepper_x_position_min = printer.fastconfig.settings.stepper_x.position_min|float %}
	{% set stepper_x_position_endstop = printer.fastconfig.settings.stepper_x.position_endstop|float %}
	{% set dual_carriage_position_max = printer.fastconfig.settings.dual_carriage.position_max|float %}
	{% set dual_carriage_position_endstop = printer.fastconfig.settings.dual_carriage.position_endstop|float %}
	{% set x_parking_space = parking_position_t0 - (stepper_x_position_endstop , stepper_x_position_min)|max %}
	{% set dc_parking_space = (dual_carriage_position_endstop , dual_carriage_position_max)|min - parking_position_t1 %}
	{% if svv.idex_xoffset|abs >= (x_parking_space - 0.5) or svv.idex_xoffset|abs >= (dc_parking_space - 0.5) %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Toolhead x-offset is too high for the available parking space. Calibrate your X and DC endstop positions and make sure you stay below 1mm." % (copy_mode_max_width)) }
	{% endif %}
	{% endif %}
	
	
	{% if (idex_mode == "copy" or idex_mode == "mirror") and printer.fastconfig.settings.ratos.enable_gcode_transform %}
	
	{% if params.MIN_X is not defined or params.MAX_X is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Something went wrong! Missing important post processor start print parameter!") }
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE=0
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	
	{% set boundary_box_min_x = params.MIN_X|default(0)|float %}
	{% set boundary_box_max_x = params.MAX_X|default(printable_x_max)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if default_toolhead == 0 %}
	
	{% set boundary_box_max_x = boundary_box_max_x + svv.idex_xoffset %}
	{% else %}
	
	{% set boundary_box_min_x = boundary_box_min_x - svv.idex_xoffset %}
	{% endif %}
	
	{% set center_x = printable_x_max / 2.0 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set object_width = boundary_box_max_x - boundary_box_min_x %}
	{% set copy_mode_max_width = center_x %}
	{% set mirror_mode_max_width = center_x - safe_distance / 2.0 %}
	
	DEBUG_ECHO PREFIX="START_PRINT" MSG="OBJECT_WIDTH: {object_width} BOUNDARY_BOX_MIN_X: {boundary_box_min_x} BOUNDARY_BOX_MAX_X: {boundary_box_max_x} CENTER_X: {center_x} SAFE_DISTANCE: {safe_distance}"
	
	
	{% if idex_mode == "copy" and object_width > copy_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for copy mode! Max supported width is %s mm" % (copy_mode_max_width)) }
	{% endif %}
	{% if idex_mode == "mirror" and object_width > mirror_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for mirror mode! Max supported width is %s mm" % (mirror_mode_max_width)) }
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = (printable_x_max - boundary_box_max_x - boundary_box_min_x) / 2 %}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE={object_xoffset}
	{% endif %}
	
	{% endif %}
	
	
	{% set has_initial_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_toolhead_filament_sensor %}
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% set has_initial_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_bowden_filament_sensor %}
	
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% if printer["dual_carriage"] is defined and both_toolheads %}
	
	{% set has_secondary_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set has_secondary_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_CHAMBER_FILTER_ON AT="before_print_start"
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true' %}
	{% if both_toolheads %}
	RATOS_ECHO MSG="Spool join is not possible if both toolheads are in use!"
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	{% endif %}
	
	
	CLEAR_PAUSE
	{% if printer["gcode_macro RatOS"].force_absolute_position|lower == 'true' %}
	G90
	{% endif %}
	SAVE_GCODE_STATE NAME=start_print_state
	
	
	G21
	
	G90
	
	M82
	_USER_START_PRINT_BEFORE_HOMING { rawparams }
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_BEGIN_BATCH
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_Z_HOP
	
	
	{% if idex_mode != '' and not (printer.fastconfig.settings.beacon is defined and (beacon_contact_start_print_true_zero or beacon_adaptive_heat_soak)) %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	{% if chamber_temp > 0 %}
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED={printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float}
	{% endif %}
	{% endif %}
	_CHAMBER_HEATER_ON START_CHAMBER_TEMP={start_chamber_temp} CHAMBER_TEMP={chamber_temp}
	_USER_START_PRINT_HEAT_CHAMBER { rawparams } CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_START_PRINT_BEFORE_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	RATOS_ECHO MSG="Heating bed..."
	
	M190 S{bed_temp}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_adaptive_heat_soak %}
	_MOVE_TO_SAFE_Z_HOME
	
	G1 Z2.5 F{z_speed}
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK LAYER_QUALITY={beacon_adaptive_heat_soak_layer_quality} MAXIMUM_FIRST_LAYER_DURATION={beacon_adaptive_heat_soak_maximum_first_layer_duration} MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={beacon_adaptive_heat_soak_max_wait}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_BED { rawparams }
	
	
	_START_PRINT_AFTER_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	_USER_START_PRINT_BED_MESH { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_BED_MESH X0={X0} X1={X1} Y0={Y0} Y1={Y1} T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_END_BATCH
	{% endif %}
	
	
	{% if idex_mode == '' %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[initial_tool]|float}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[0]|float}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={extruder_first_layer_temp[1]|float}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_PARK { rawparams }
	
	
	_START_PRINT_PARK
	
	
	RATOS_ECHO MSG="Heating Extruder..."
	{% if idex_mode == '' %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[initial_tool]|float}  MAXIMUM={extruder_first_layer_temp[initial_tool]|float + 5}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[0]|float}  MAXIMUM={extruder_first_layer_temp[0]|float + 5}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder1" MINIMUM={extruder_first_layer_temp[1]|float}  MAXIMUM={extruder_first_layer_temp[1]|float + 5}
	{% endif %}
	{% endif %}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	{% if idex_mode == '' %}
	_LED_PRINTING
	{% else %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	_LED_PRINTING
	{% else %}
	{% if both_toolheads %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	{% if toolchange_standby_temp > -1 %}
	_LED_TOOLHEAD_STANDBY TOOLHEAD={0 if initial_tool == 1 else 1}
	{% else %}
	_LED_PRINTING TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% else %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_EXTRUDER { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_AFTER_HEATING_EXTRUDER X0={X0} X1={X1} Y0={Y0} Y1={Y1} INITIAL_TOOLHEAD={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if idex_mode != '' %}
	{% if not both_toolheads %}
	{% if initial_tool != default_toolhead %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if idex_mode != '' %}
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=standby VALUE=False
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=standby VALUE=False
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if initial_tool == 1 else 'extruder1'} TARGET={toolchange_standby_temp}
	SET_GCODE_VARIABLE MACRO=T{0 if initial_tool == 1 else 1} VARIABLE=standby VALUE=True
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=start_print_state
	
	{% if printer["dual_carriage"] is defined %}
	_SET_IDEX_MODE_OFFSET
	{% endif %}
	
	
	{% if idex_mode != '' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% if idex_mode == "copy" and idex_mode != act_idex_mode %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == "mirror" and idex_mode != act_idex_mode %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={object_xoffset} MOVE=0
	{% endif %}
	{% else %}
	_SELECT_TOOL T={initial_tool} TOOLSHIFT=false
	_SET_TOOLHEAD_OFFSET
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	_SET_EXTRUSION_MODE
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={printer["print_stats"].print_duration}
	{% endif %}
	
	
	_USER_END_START_PRINT { rawparams }
	
	G92 E0
	
	
	_CHAMBER_FILTER_ON AT="after_print_start"
	
	_ALERT_NON_ZERO_Z_OFFSET
	
	RATOS_ECHO MSG="Printing..."

[gcode_macro _START_PRINT_BEFORE_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set is_stowable_probe = true if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' else false %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Pre-heating extruder..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={min_temp}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET={min_temp}
	{% endif %}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	{% endif %}
	{% endif %}
	
	
	{% if not is_stowable_probe %}
	{% if printer["dual_carriage"] is defined and act_t != default_toolhead %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	{% endif %}
	RATOS_ECHO MSG="Heat soaking z probe..."
	_MOVE_TO_SAFE_Z_HOME
	
	G0 Z2 F{z_speed}
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Waiting for extruder to be preheated..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	{% if default_toolhead == 0 %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_Z_HOP
	{% endif %}
	
	
	{% if auto_z_offset_calibration %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	PARK_TOOLHEAD
	_CLEANING_MOVE TOOLHEAD={default_toolhead} AUTOMATED=True
	_SELECT_TOOL T={0 if default_toolhead == 1 else 1} X={parking_position_t0 if default_toolhead == 1 else parking_position_t1} Y=0 TOOLSHIFT=false
	_CLEANING_MOVE TOOLHEAD={0 if default_toolhead == 1 else 1} AUTOMATED=True
	_VAOC_CALIBRATE_Z_OFFSET AUTO_Z_OFFSET=True
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=false
	{% endif %}
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	{% if needs_rehoming %}
	G28 Z
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	_START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE
	{% endif %}
	{% endif %}
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	PROBE PROBE_METHOD=contact SAMPLES=1

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	{% set fuzzy_radius = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_radius|default(0)|float if beacon_contact_start_print_true_zero_fuzzy_position else 0 %}
	
	{% set contact_true_zero_temp_has_been_set = False %}
	
	
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	
	
	
	{% if printer.beacon.last_probe_result|lower == "ok" %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	RATOS_ECHO MSG="Auto calibration nozzle wipe with probe result {last_z_offset}..."
	G0 Z{(0.2 + last_z_offset)} F{z_speed}
	G0 X70 F300
	{% else %}
	RATOS_ECHO MSG="Skipping auto calibration nozzle wipe because probing failed!"
	{% endif %}
	{% elif beacon_contact_wipe_before_true_zero_method == "probe_clean" %}
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	
	{% set contact_true_zero_temp_has_been_set = True %}
	
	
	
	
	
	
	
	
	BEACON_PROBE_CLEAN X=50 Y=10
	{% else %}
	CONSOLE_ECHO TYPE="error" TITLE="Unknown wipe method" MSG="Unknown wipe method '{beacon_contact_wipe_before_true_zero_method}' configured, skipping wipe before beacon true zero."
	{% endif %}
	{% endif %}
	
	
	G0 Z5 F{z_speed}
	_MOVE_TO_SAFE_Z_HOME FUZZY_RADIUS={fuzzy_radius}
	
	
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION
	
	{% if not contact_true_zero_temp_has_been_set %}
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon contact auto calibration..."
	
	{% if beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	
	G0 Z5 F{z_speed}

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION]
gcode = 
	{% set pos = printer.ratos.last_move_to_safe_z_home_position %}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE={pos[0]}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE={pos[1]}

[gcode_macro _START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set first_x = printer["gcode_macro START_PRINT"].first_x|default(-1)|float %}
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2.0 %}
	{% set center_y = printable_y_max / 2.0 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% if printer["dual_carriage"] is defined %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% endif %}
	
	
	{% set X0 = params.X0|default(-1)|int %}
	{% set X1 = params.X1|default(-1)|int %}
	{% set Y0 = params.Y0|default(-1)|int %}
	{% set Y1 = params.Y1|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	
	{% if idex_mode == '' %}
	
	_PRIME
	{% else %}
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	RATOS_ECHO PREFIX="IDEX" MSG="using combined prime offset for IDEX {idex_mode} mode"
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	{% if both_toolheads %}
	{% if initial_toolhead == 0 %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T{initial_toolhead}"
	_SELECT_TOOL T={initial_toolhead} TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	SET_MACRO_TRAVEL_SETTINGS
	
	{% if (X0 > -1 and Y1 > -1) or (first_x > 0 and first_y > 0) %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	{% endif %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	{% set first_z = 1 %}
	{% else %}
	{% set first_z = 3 %}
	{% endif %}
	
	
	{% if idex_mode == "mirror" %}
	{% if first_y >= 0 %}
	G0 Y{first_y} F{speed}
	{% else %}
	G0 Y{Y1} F{speed}
	{% endif %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={initial_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={initial_toolhead} E={printer["gcode_macro RatOS"].toolchange_first_purge|default(50)|float}
	_CLEANING_MOVE TOOLHEAD={initial_toolhead} AUTOMATED=True
	{% endif %}
	{% if first_x >= 0 and first_y >= 0 %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% else %}
	{% set first_x = X0 %}
	{% set first_y = Y0 %}
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'min' %}
	{% set first_x = X0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'max' %}
	{% set first_x = X1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|float <= center_x %}
	{% set first_x = X0 %}
	{% else %}
	{% set first_x = X1 %}
	{% endif %}
	{% endif %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'min' %}
	{% set first_y = Y0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'max' %}
	{% set first_y = Y1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|float <= center_y %}
	{% set first_y = Y0 %}
	{% else %}
	{% set first_y = Y1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	
	
	_LOAD_RATOS_SKEW_PROFILE

[gcode_macro _PRIME]
gcode = 
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	PRIME_BLOB INITIAL_TOOLHEAD={params.INITIAL_TOOLHEAD} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={params.IDEX_MODE} Y1={params.Y1}
	{% else %}
	
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif params.IDEX_MODE == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro END_PRINT]
description = End print procedure, use this in your Slicer.
gcode = 
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SAVE_GCODE_STATE NAME=end_print_state
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = printer["gcode_macro START_PRINT"].object_xoffset|default(0)|float %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(0-object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={(0-object_xoffset)}
	{% endif %}
	{% endif %}
	
	
	_USER_END_PRINT_BEFORE_HEATERS_OFF { rawparams }
	_END_PRINT_BEFORE_HEATERS_OFF
	TURN_OFF_HEATERS
	_USER_END_PRINT_AFTER_HEATERS_OFF { rawparams }
	_END_PRINT_AFTER_HEATERS_OFF
	_USER_END_PRINT_PARK { rawparams }
	_END_PRINT_PARK
	
	
	{% if printer["gcode_macro RatOS"].skew_profile is defined %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined and printer["gcode_macro RatOS"].end_print_motors_off|lower != 'false' %}
	
	M84
	{% endif %}
	
	
	M107
	
	
	BED_MESH_CLEAR
	RATOS_ECHO MSG="Done :)"
	
	
	RESTORE_GCODE_STATE NAME=end_print_state
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	M84
	{% endif %}
	
	
	RESET_NAMED_OFFSET EVENT="end_print"
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_CHAMBER_FILTER_ON AT="print_end"
	_CHAMBER_FILTER_OFF
	
	
	_CHAMBER_HEATER_OFF
	
	_USER_END_PRINT_FINISHED { rawparams }

[gcode_macro _END_PRINT_BEFORE_HEATERS_OFF]
gcode = 
	RATOS_ECHO MSG="Cleaning up..."

[gcode_macro _END_PRINT_AFTER_HEATERS_OFF]
gcode = 
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% set z_hop = printer["gcode_macro RatOS"].end_print_park_z_hop|float %}
	{% set r = printer["gcode_macro RatOS"].end_print_retract_filament|default(4)|float %}
	{% if current_z < (max_z - z_hop) %}
	{% set z_safe = z_hop %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G91
	
	{% if can_extrude %}
	G1 E-2 F3600
	{% endif %}
	
	G0 Z{z_safe} F3600
	
	{% if can_extrude %}
	G1 E-{(r-2)} F3600
	{% endif %}
	
	G90

[gcode_macro _SET_EXTRUSION_MODE]
gcode = 
	
	{% if printer["gcode_macro RatOS"].relative_extrusion|lower == 'true' %}
	M83
	{% else %}
	M82
	{% endif %}

[gcode_macro GENERATE_SHAPER_GRAPHS]
description = Genarates input shaper resonances graphs for analysis. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	{% set hz_per_sec = params.HZ_PER_SEC|default(1)|float %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set copy_mode_offset = printable_x_max / 4.0 %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	_IDEX_SINGLE
	{% endif %}
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	
	
	{% if idex_mode != 'copy' and idex_mode != 'mirror' %}
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	{% endif %}
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Shaper graph"

[gcode_shell_command generate_shaper_graph_x]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-x.sh
timeout = 60.
verbose = True

[gcode_shell_command generate_shaper_graph_y]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-y.sh
timeout = 60.
verbose = True

[gcode_macro MEASURE_COREXY_BELT_TENSION]
description = Generates resonance graph used to ensure belts are equally tensioned. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	_IDEX_SINGLE
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if measure_t1 == false or measure_t0 == false %}
	{action_raise_error("Axis specified. Not supported for belt tension on Y.")}
	{% else %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	G4 P5000
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	PARK_TOOLHEAD
	{% endif %}
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	G1 X{parking_position_t1} F{speed}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	
	
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Belt Tension Graph"

[gcode_shell_command generate_belt_tension_graph]
command = /home/pi/printer_data/config/RatOS/scripts/generate-belt-tension-graph.sh
timeout = 90.
verbose = True

[idle_timeout]
gcode = 
	{% if printer.webhooks.state|lower == 'ready' %}
	{% if printer.pause_resume.is_paused|lower == 'false' %}
	_USER_BEFORE_IDLE_TIMEOUT
	RATOS_ECHO PREFIX="IDLE" MSG="2 hours since last activity. Powering off heaters and motors.."
	TURN_OFF_HEATERS
	M84
	_USER_AFTER_IDLE_TIMEOUT
	{% endif %}
	{% endif %}
timeout = 7200

[temperature_sensor raspberry_pi]
sensor_type = temperature_host

[skew_correction]

[named_offsets]

[input_shaper]

[virtual_sdcard]
path = ~/printer_data/gcodes

[display_status]

[pause_resume]

[force_move]
enable_force_move = True

[respond]

[resonance_generator]

[ratos]
allow_unknown_gcode_generator = True
enable_gcode_transform = True

[exclude_object]

[bed_mesh]
split_delta_z = 0.001
horizontal_move_z = 2
mesh_min = 20,20
mesh_max = 480,480
probe_count = 40,40
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = .2
speed = 600
log_points = False

[fastconfig]

[heater_bed]
heater_pin = heater_bed_heating_pin
sensor_pin = heater_bed_sensor_pin
sensor_type = Generic 3950
min_temp = 0
max_temp = 140
pwm_cycle_time = 0.103
control = pid
pid_kp = 61.987
pid_ki = 1.781
pid_kd = 539.289

[printer]
kinematics = ratos_hybrid_corexy
max_velocity = 800
max_accel = 10000
minimum_cruise_ratio = 0.5
max_z_velocity = 50
max_z_accel = 600
square_corner_velocity = 5

[ratos_hybrid_corexy]
inverted = true

[dual_carriage]
axis = x
safe_distance = 55
position_max = 559.6
position_endstop = 559.6
position_min = 0
step_pin = PF9
dir_pin = dual_carriage_dir_pin
enable_pin = !PG2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t1:PA2

[gcode_macro _SET_IDEX_MODE_OFFSET]
description = "Internal use only. Sets the 'idex_mode' named offset that the active idex mode requires."
gcode = 
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_SET_IDEX_MODE_OFFSET" MSG="idex_mode: {idex_mode}, center_x: {center_x}"
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	SET_NAMED_OFFSET NAME=idex_mode X={(-center_x / 2)}
	{% else %}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% else %}
	{action_raise_error("_SET_IDEX_MODE_OFFSET: Printer not homed")}
	{% endif %}

[gcode_macro IDEX_SINGLE]
gcode = 
	_IDEX_REMAP_TOOLHEADS ENABLE=False
	_IDEX_SINGLE

[gcode_macro _IDEX_SINGLE]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_single"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set init = params.INIT|default(0)|int %}
	{% set new_x = params.X|default(-1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_default_t = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="init: {init}, new_x: {new_x}, idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, act_t: {act_t}"
	
	{% if idex_mode == "copy" or idex_mode == "mirror" or init == 1 %}
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="reset idex_mode offset"
	G1 X{center_x} F{(speed)}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="activate default carriage"
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolheads"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	G90
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position."
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1}
	G1 X{parking_position_default_t} F{speed}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move default toolhead to its new position."
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% if new_x == -1 %}
	{% set new_x = center_x %}
	{% endif %}
	G1 X{new_x} F{speed}
	
	M400
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="X Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set extruder motion queue."
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if default_toolhead==0 else default_toolhead}
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolhead offset."
	_SET_TOOLHEAD_OFFSET
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set input shaper."
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[default_toolhead]|float)} SHAPER_FREQ_Y={(shaper_y_freq[default_toolhead]|float)} SHAPER_TYPE_X={(shaper_x_type[default_toolhead]|lower)} SHAPER_TYPE_Y={(shaper_y_type[default_toolhead]|lower)}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="update Frontend."
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if default_toolhead==0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if default_toolhead==1 else False}
	{% else %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_single"

[gcode_macro IDEX_COPY]
gcode = 
	_IDEX_COPY

[gcode_macro _IDEX_COPY]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_copy"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set y = params.Y|default(-1)|int %}
	{% set dance = params.DANCE|default(1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_COPY" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}, y: {y}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "copy" %}
	{% if idex_mode == "mirror" %}
	{% if y>=0 %}
	G1 X{center_x} Y{y} F{(speed)}
	{% else %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	
	
	{% if idex_mode != "mirror" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance == 1 %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[2]|float)} SHAPER_FREQ_Y={(shaper_y_freq[2]|float)} SHAPER_TYPE_X={(shaper_x_type[2]|lower)} SHAPER_TYPE_Y={(shaper_y_type[2]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_copy"

[gcode_macro IDEX_MIRROR]
gcode = 
	_IDEX_MIRROR

[gcode_macro _IDEX_MIRROR]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_mirror"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set dance = params.DANCE|default(1)|int %}
	{% set priming = params.PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_MIRROR" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "mirror" %}
	
	{% if idex_mode == "copy" %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS MIRROR_PRIMING={params.PRIMING}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=MIRROR
	
	
	{% if idex_mode != "copy" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance and not priming %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[3]|float)} SHAPER_FREQ_Y={(shaper_y_freq[3]|float)} SHAPER_TYPE_X={(shaper_x_type[3]|lower)} SHAPER_TYPE_Y={(shaper_y_type[3]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_mirror"

[gcode_macro _IDEX_SET_TOOLHEADS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set mirror_priming = params.MIRROR_PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position_inactive_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_IDEX_SET_TOOLHEADS" MSG="idex_mode: {idex_mode}, act_t: {act_t}, center_x: {center_x}, mirror_priming: {mirror_priming}"
	
	
	{% if act_t != default_toolhead %}
	_SET_TOOLHEAD_OFFSET FORCE_TOOLHEAD={default_toolhead} MOVE=1
	{% endif %}
	
	{% if mirror_priming %}
	
	
	
	{% if parking_position_t0|abs < parking_position_t1 - printable_x_max %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{printable_x_max + parking_position_t0|abs} F{(speed)}
	{% else %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{0 - (parking_position_t1 - printable_x_max)} F{(speed)}
	{% endif %}
	
	{% else %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1} MODE=PRIMARY
	G1 X{parking_position_inactive_t} F{(speed)}
	
	
	{% if act_t==1 %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{center_x / 2} F{(speed)}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"

[gcode_macro IDEX_PARK]
gcode = 
	
	PARK_TOOLHEAD

[gcode_macro PARK_TOOLHEAD]
gcode = 
	
	{% set idex_mode = 'none' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="PARK_TOOLHEAD" MSG="Parking T{act_t}.."
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set parking_position_inact_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set printable_y_min = printer["gcode_macro RatOS"].printable_y_min|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" and 'xy' in printer.toolhead.homed_axes %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% elif printer.toolhead.position.y|float < printable_y_min %}
	G1 Y{printable_y_min} F{speed}
	{% endif %}
	
	SAVE_GCODE_STATE NAME=_PARK_TOOLHEAD
	G90
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0.5
	
	
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_inact_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	
	SET_VELOCITY_LIMIT ACCEL={printer.toolhead.max_accel} MINIMUM_CRUISE_RATIO=0.5
	M400
	RESTORE_GCODE_STATE NAME=_PARK_TOOLHEAD
	
	{% endif %}

[gcode_macro JOIN_SPOOLS]
gcode = 
	
	{% set spools = params.SPOOLS|default("") %}
	
	{% if spools == "" %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% else %}
	{% if spools != "0,1" and spools != "1,0" %}
	RATOS_ECHO MSG="Wrong spool configuration!"
	RATOS_ECHO MSG="Join Spools = JOIN_SPOOLS SPOOLS=0,1"
	RATOS_ECHO MSG="Deactivate = JOIN_SPOOLS SPOOLS="
	{% else %}
	{% if spools == "0,1" or spools == "1,0" %}
	_IDEX_JOIN_SPOOLS ENABLE=true
	{% else %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_JOIN_SPOOLS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if enable %}
	{% set has_t0_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t1_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t0_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined else false %}
	{% set has_t1_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined else false %}
	{% if (has_t0_toolhead_filament_sensor and has_t1_toolhead_filament_sensor) or (has_t0_bowden_filament_sensor and has_t1_bowden_filament_sensor) %}
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=True
	RATOS_ECHO MSG="Spool joining enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Can not enable spool joining! No filament sensors found."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining deactivated!"
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining is not possible in copy and mirror mode!"
	{% endif %}

[gcode_macro _JOIN_SPOOL]
gcode = 
	
	{% set old_toolhead = params.TOOLHEAD|int %}
	{% set new_toolhead = 0 if old_toolhead == 1 else 1 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set purge_after_load = printer["gcode_macro T%s" % new_toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_JOIN_SPOOL" MSG="toolhead: {new_toolhead}"
	
	{% set has_filament = true %}
	{% set has_new_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% set has_new_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% if has_new_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	{% if has_new_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	
	{% if has_filament %}
	RATOS_ECHO MSG="Joining spools! Please wait for extruder to heat up...."
	
	
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={new_toolhead}
	
	
	_DEACTIVATE_TOOLHEAD TOOLHEAD={old_toolhead}
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set extruder_temp = extruder_first_layer_temp[new_toolhead]|float %}
	{% else %}
	{% set extruder_temp = extruder_other_layer_temp[new_toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if new_toolhead == 0 else 'extruder1'} TARGET={extruder_temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if new_toolhead == 0 else 'extruder1'} MINIMUM={extruder_temp}  MAXIMUM={extruder_temp + 5}
	
	
	{% if purge_after_load > 0 %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_toolhead == 0 else new_toolhead}
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={new_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={new_toolhead} E={purge_after_load}
	_CLEANING_MOVE TOOLHEAD={new_toolhead} AUTOMATED=True
	
	
	SET_DUAL_CARRIAGE CARRIAGE={old_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if old_toolhead == 0 else old_toolhead}
	
	{% endif %}
	
	
	RESUME TOOLHEAD={new_toolhead}
	
	
	_IDEX_JOIN_SPOOLS ENABLE=false
	
	{% else %}
	{ action_raise_error("Spool join failed! No filament found or filament sensor is disabled.") }
	{% endif %}

[gcode_macro REMAP_TOOLHEADS]
gcode = 
	
	{% set toolheads = params.TOOLHEADS|default("") %}
	
	{% if toolheads == "" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% else %}
	{% if toolheads != "0,1" and toolheads != "1,0" %}
	RATOS_ECHO MSG="Wrong toolhead configuration!"
	RATOS_ECHO MSG="Remap = REMAP_TOOLHEADS TOOLHEADS=0,1"
	RATOS_ECHO MSG="Deactivate = REMAP_TOOLHEADS TOOLHEADS="
	{% else %}
	{% if toolheads == "0,1" or toolheads == "1,0" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=true
	_IDEX_SINGLE
	{% else %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_REMAP_TOOLHEADS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	{% if not enable or (idex_mode != "copy" and idex_mode != "mirror") %}
	{% if enable %}
	RATOS_ECHO MSG="Toolhead remapping enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping deactivated!"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE={enable}
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping not possible in copy and mirror mode!"
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	{% endif %}

[gcode_macro SHAPER_CALIBRATE]
rename_existing = SHAPER_CALIBRATE_ORG
gcode = 
	RATOS_ECHO PREFIX="IDEX" MSG="SHAPER_CALIBRATE is useless on IDEX machines. Please use the GENERATE_SHAPER_GRAPHS macro and type the values into `variable_shaper_*_freq` and `variable_shaper_*_type manually`."

[gcode_shell_command generate_shaper_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-shaper-graph.sh
timeout = 120.
verbose = True

[gcode_shell_command generate_tension_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-belt-tension-graph.sh
timeout = 120.
verbose = True

[gcode_macro SET_PRESSURE_ADVANCE]
variable_snyc_toolheads = False
rename_existing = SET_PRESSURE_ADVANCE_BASE
gcode = 
	{% if params.SYNC_TOOLHEADS is defined %}
	{% set snyc_toolheads = true if params.SYNC_TOOLHEADS|default(false)|lower == 'true' else false %}
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=True
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="Syncing toolheads..."
	{% else %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' or snyc_toolheads %}
	{% set advance = params.ADVANCE|default(printer['extruder'].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['extruder'].smooth_time|float)|float %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T0"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T1"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder1' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% else %}
	{% set extruder = 'extruder' if act_t == 0 else 'extruder1' %}
	{% if params.EXTRUDER is defined %}
	{% set extruder = params.EXTRUDER %}
	{% endif %}
	{% if extruder == 'extruder' or extruder == 'extruder1' %}
	{% set advance = params.ADVANCE|default(printer['%s' % extruder].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['%s' % extruder].smooth_time|float)|float %}
	SET_PRESSURE_ADVANCE_BASE EXTRUDER={extruder} ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% if params.EXTRUDER is not defined %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG={"T%s" % act_t}
	{% endif %}
	{% else %}
	SET_PRESSURE_ADVANCE_BASE { rawparams }
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro M106]
rename_existing = M106.1
variable_swap_speed = -1
gcode = 
	
	{% set s = [[params.S|default(255)|int, 255]|min, 0]|max %}
	{% set p = params.P|default(-1)|int %}
	{% set speed = s / 255 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set t = 1 if idex_mode=='primary' else 0 %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(0)|int == 1 else false %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set sync_fans = true %}
	{% endif %}
	
	
	{% if sync_fans and idex_mode != "copy" and idex_mode != "mirror" %}
	
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int %}
	
	
	{% if toolshift_count > total_toolshifts %}
	{% set sync_fans = false %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE=-1
	
	
	{% if p == -1 %}
	
	{% if speed == 0 %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed}
	{% else %}
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE={speed}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={(speed if (t == 0 or sync_fans) else 0)}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={(speed if (t == 1 or sync_fans) else 0)}
	{% endif %}
	{% else %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed if t == p else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed if t == p else 0}
	{% endif %}
	
	
	M106.1 S{s}

[gcode_macro M107]
rename_existing = M107.1
gcode = 
	{% set p = params.P|default(-1)|int %}
	M106 S0 P{p}

[gcode_macro _SELECT_TOOL]
variable_last_timestamp = 0
gcode = 
	{% if params.T is defined %}
	{% set idex_mode = '' %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if "xyz" not in printer.toolhead.homed_axes and (idex_mode == "copy" or idex_mode == "mirror") %}
	_IDEX_SINGLE
	{% set idex_mode = 'reset' %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set new_t = params.T|int %}
	
	
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads and is_printing_gcode %}
	{% set new_t = 0 if new_t == 1 else 1 %}
	{% endif %}
	
	
	{% set toolchange_prepurging_timer = printer["gcode_macro RatOS"].toolchange_prepurging_timer|default(0)|int %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	DEBUG_ECHO PREFIX="_SELECT_TOOL" MSG="act_t: {act_t}, new_t: {new_t}, is_printing_gcode: {is_printing_gcode}, swap_toolheads: {swap_toolheads}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	{% set act_extruder = 'extruder%s' % ('' if new_t == 0 else new_t) %}
	{% if new_t != act_t or printer.toolhead.extruder != act_extruder or idex_mode == 'reset' %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Selecting T{new_t}.."
	
	
	M220 S100
	
	
	
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(1)|int == 1 else false %}
	
	
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set toolshift = false %}
	{% endif %}
	
	
	{% set fan_speed = printer["fan_generic part_fan_t%s" % act_t].speed %}
	
	
	{% set deactivate_toolhead = false %}
	{% if is_printing_gcode %}
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int + 1 %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE={toolshift_count}
	{% if toolshift_count == total_toolshifts %}
	{% set deactivate_toolhead = true %}
	{% endif %}
	{% endif %}
	
	
	{% set needs_wakeup = true if printer["gcode_macro T%s" % new_t].standby|default(false)|lower == 'true' else false %}
	
	
	{% set needs_purging = false %}
	{% set wake_up_purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% if is_printing_gcode and toolchange_prepurging_timer > 0 and wake_up_purge > 0 %}
	{% set new_timestamp = printer["print_stats"].print_duration %}
	{% set elapsed_time = new_timestamp - last_timestamp %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={new_timestamp}
	{% if elapsed_time > toolchange_prepurging_timer %}
	{% set needs_purging = true %}
	{% endif %}
	{% endif %}
	
	
	{% set first_use_purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% if toolshift_count == 1 and first_use_purge > 0 %}
	{% set needs_purging = true %}
	{% endif %}
	
	
	{% if is_printing_gcode and (toolchange_standby_temp > -1 or needs_purging or needs_wakeup) %}
	_TOOLHEAD_STANDBY TOOLHEAD={act_t}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	_TOOLHEAD_WAKEUP TOOLHEAD={new_t} X={new_x} Y={new_y} Z={new_z} FAN_SPEED={fan_speed} TOOLSHIFT_COUNT={toolshift_count}
	{% else %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(false)|lower == 'true' else false %}
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if (new_t == 0 or sync_fans) else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if (new_t == 1 or sync_fans) else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	_TOOLCHANGE T={new_t} X={new_x} Y={new_y} Z={new_z} PARK_T0={park_t0} PARK_T1={park_t1} TOOLSHIFT={toolshift}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[new_t]|float)} SHAPER_FREQ_Y={(shaper_y_freq[new_t]|float)} SHAPER_TYPE_X={(shaper_x_type[new_t]|lower)} SHAPER_TYPE_Y={(shaper_y_type[new_t]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if new_t == 0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if new_t == 1 else False}
	
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% set sanity_check_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if new_t == 0 %}
	{% if printer.toolhead.extruder == 'extruder' %}
	{% if sanity_check_idex_mode == 'primary' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% elif new_t == 1 %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% if sanity_check_idex_mode == 'inactive' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _TOOLHEAD_STANDBY]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Putting toolhead T{toolhead} into standby mode."
	DEBUG_ECHO PREFIX="_TOOLHEAD_STANDBY" MSG="toolhead: {toolhead}, config_z_hop: {config_z_hop}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={toolhead} SYNC=0
	PARK_TOOLHEAD
	
	
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={toolchange_standby_temp}
	{% endif %}
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=True
	{% endif %}
	
	
	_LED_TOOLHEAD_STANDBY TOOLHEAD={toolhead}

[gcode_macro _TOOLHEAD_WAKEUP]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set fan_speed = params.FAN_SPEED|float %}
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift_count = params.TOOLSHIFT_COUNT|default(0)|int %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% if toolshift_count == 1 %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% endif %}
	{% set needs_wakeup = true if printer["gcode_macro T%s" % toolhead].standby|default(false)|lower == 'true' else false %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Waking up toolhead T{toolhead}. Please wait for extruder to heat up..."
	DEBUG_ECHO PREFIX="_TOOLHEAD_WAKEUP" MSG="toolhead: {toolhead}, fan_speed: {fan_speed}, new_x: {new_x}, new_y: {new_y}, new_z: {new_z}, config_z_hop: {config_z_hop}"
	
	
	_LED_TOOLHEAD_WAKEUP TOOLHEAD={toolhead}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={toolhead} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE=1
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if toolhead == 0 else toolhead}
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if needs_wakeup %}
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set temp = extruder_first_layer_temp[toolhead]|float %}
	{% else %}
	{% set temp = extruder_other_layer_temp[toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if toolhead == 0 else 'extruder1'} MINIMUM={temp}  MAXIMUM={temp + 5}
	{% endif %}
	
	
	_LED_PRINTING TOOLHEAD={toolhead}
	
	
	{% if purge > 0 %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={toolhead} E={purge}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	
	
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if toolhead == 1 else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	G92 E0
	G1 E-{e} F{feedrate}
	G92 E0
	
	
	{% if new_x >= 0 and new_y >= 0 %}
	G1 X{new_x} Y{new_y} F{speed}
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={config_z_hop} T={toolhead} SYNC=0
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=False

[gcode_macro _TOOLCHANGE]
variable_toolshift_count = 0
gcode = 
	
	
	{% set new_t = params.T|default(-1)|int %}
	{% set new_x = params.X|default(-1.0)|float %}
	{% set new_y = params.Y|default(-1.0)|float %}
	{% set new_z = params.Z|default(-1.0)|float %}
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(true)|lower == 'true' else false %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T: {new_t}, X: {new_x}, Y: {new_y}, Z: {new_z}, PARK_T0: {park_t0}, PARK_T1: {park_t1}, IS_PRINTING_GCODE: {is_printing_gcode}, TOOLSHIFT: {toolshift}"
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	{% if park_t0 >= 0 and park_t1 >= 0 %}
	{% set parking_position_t0 = park_t0 %}
	{% set parking_position_t1 = park_t1 %}
	{% set parking_position_act_t = park_t0 if act_t == 0 else park_t1 %}
	{% endif %}
	
	
	{% if not is_printing_gcode and not toolshift %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Changing tool to T{new_t} without retracting/extruding or moving the toolheads except for parking."
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	G90
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% if not is_printing_gcode and toolshift and new_x < 0 and new_y < 0 %}
	{% set new_x = center_x %}
	{% set new_y = printer.gcode_move.gcode_position.y|float %}
	{% endif %}
	
	{% if new_x < 0 or new_y < 0 %}
	
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="No new X or Y position given, parking the active toolhead and activating the new toolhead without moving it."
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={new_t}
	
	
	{% if "x" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	{% if is_printing_gcode %}
	_EXTRUDE T={new_t}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	{% if "xyz" not in printer.toolhead.homed_axes %}
	
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	
	
	{% set svv = printer.save_variables.variables %}
	{% if new_t == default_toolhead %}
	{% set new_xoffset = 0 %}
	{% set new_yoffset = 0 %}
	{% set new_zoffset = 0 %}
	{% else %}
	{% set new_xoffset = -svv.idex_xoffset %}
	{% set new_yoffset = -svv.idex_yoffset %}
	{% set new_zoffset = -svv.idex_zoffset %}
	{% endif %}
	
	{% set xoffset_correction = new_xoffset - printer.named_offsets.toolhead_alignment.x %}
	{% set yoffset_correction = new_yoffset - printer.named_offsets.toolhead_alignment.y %}
	{% set zoffset_correction = new_zoffset - printer.named_offsets.toolhead_alignment.z %}
	
	{% if new_t == 0 %}
	
	{% set t0_act_x = parking_position_t0 %}
	{% set t1_act_x = printer.toolhead.position.x|float %}
	{% set t0_new_x = new_x %}
	{% set t1_new_x = parking_position_t1 %}
	{% set t0_distance = t0_new_x - t0_act_x %}
	{% set t1_distance = t1_new_x - t1_act_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T0."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	
	
	G1 X{t0_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x + (t1_new_x - t1_act_x)} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t0_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T0: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% elif new_t == 1 %}
	
	{% set t0_act_x = printer.toolhead.position.x|float %}
	{% set t1_act_x = parking_position_t1 %}
	{% set t0_new_x = parking_position_t0 %}
	{% set t1_new_x = new_x %}
	{% set t0_distance = t0_act_x - t0_new_x %}
	{% set t1_distance = t1_act_x - t1_new_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T1."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x - t1_distance + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t1_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T1: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% endif %}
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	{% endif %}

[gcode_macro _ZHOP_BEFORE_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_hop = params.Z_HOP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_HOP: {z_hop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="COMBINED_ZHOP G1 Z+{z_hop} E-{e} F{speed * 60}"
	G1 Z+{z_hop} E-{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="ZHOP G1 Z+{z_hop} F{speed * 60}"
	G1 Z+{z_hop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="RETRACT G1 E-{e} F{feedrate}"
	G1 E-{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _ZDROP_AFTER_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_drop = params.Z_DROP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_DROP: {z_drop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="COMBINED_ZDROP G1 Z-{z_drop} E{e} F{speed * 60}"
	G1 Z-{z_drop} E{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="ZDROP G1 Z-{z_drop} F{speed * 60}"
	G1 Z-{z_drop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="EXTRUDE G1 E{e} F{feedrate}"
	G1 E{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _EXTRUDE]
gcode = 
	
	{% set t = params.T|int %}
	
	
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	
	DEBUG_ECHO PREFIX="_EXTRUDE" MSG="G1 E{e} F{feedrate * 60}"
	
	
	G91
	M82
	G92 E0
	G1 E{e} F{feedrate * 60}
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _DEACTIVATE_TOOLHEAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_DEACTIVATE_TOOLHEAD" MSG="TOOLHEAD {toolhead}"
	
	
	{% if toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% endif %}
	
	
	M106.1 S0
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={toolhead}

[delayed_gcode _INIT_TOOLHEADS]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	_IDEX_SINGLE INIT=1
	
	
	{% if printer.fastconfig.settings.dual_carriage.safe_distance is defined %}
	{% if printer.fastconfig.settings.dual_carriage.safe_distance|float < 50 %}
	{ action_emergency_stop("Dual carriage safe_distance seems to be too low!") }
	{% endif %}
	{% else %}
	{ action_emergency_stop("Dual carriage safe_distance not defined!") }
	{% endif %}

[gcode_macro _SET_TOOLHEAD_OFFSET]
description = "Internal use only. Sets the toolhead_alignment offset (and hotend_thermal_expansion offset when configured) for the active/dominant toolhead."
gcode = 
	
	{% set move = params.MOVE|default(0)|int %}
	{% set force_toolhead = params.FORCE_TOOLHEAD|default(-1)|int %}
	
	
	{% if params.T is defined %}
	CONSOLE_ECHO TYPE="error" MSG="_SET_TOOLHEAD_OFFSET called with deprectated T parameter, which is ignored."
	{';$_SET_TOOLHEAD_OFFSET_ignoring_TOOLHEAD_parameter'}
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="active/dominant toolhead: {toolhead}, MOVE: {move}, FORCE_TOOLHEAD: {force_toolhead}"
	
	
	{% if force_toolhead >= 0 %}
	{% set toolhead = force_toolhead %}
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="FORCE_TOOLHEAD applied, using TOOLHEAD: {toolhead}"
	{% endif %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set move = 0 %}
	{% endif %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|int %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X=0 Y=0 MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z=0 MOVE={move} SPEED={z_speed}
	{% else %}
	{% set svv = printer.save_variables.variables %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X={(-svv.idex_xoffset)} Y={(-svv.idex_yoffset)} MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-svv.idex_zoffset)} MOVE={move} SPEED={z_speed}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}

[gcode_macro TOOLSHIFT_CONFIG]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={params.SPEED|default(300)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={params.ACCEL|default(5000)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_retraction VALUE={params.RETRACT|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_extrusion VALUE={params.EXTRUDE|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_feedrate VALUE={params.FEEDRATE|default(7200)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={params.Z_HOP|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zspeed VALUE={params.Z_SPEED|default(25)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_combined_zhop VALUE={true if params.COMBINED_ZHOP|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_sync_fans VALUE={true if params.SYNC_FANS|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_prepurging_timer VALUE={params.AUTO_PURGE_TIME|default(0)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_purge VALUE={params.PURGE|default(25)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_standby_temp VALUE={params.STANDBY_TEMP|default(-1)|float}

[gcode_macro CALCULATE_DC_ENDSTOP]
description = "DEPRECATED: This macro has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."
gcode = 
	CONSOLE_ECHO TITLE="CALCULATE_DC_ENDSTOP has been deprecated" TYPE="error" MSG="The CALCULATE_DC_ENDSTOP has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."

[gcode_macro _VAOC]
variable_is_fixed = True
variable_is_started = False
variable_is_started_at_temp = False
variable_additional_safe_distance = 50
variable_safe_z = 30
variable_auto_z_offset_calibration = True
variable_enable_camera_cooling = True
variable_camera_cooling_fan_speed = 0.3
variable_camera_cooling_temperature = 50
variable_toolchange_travel_speed = 300
variable_toolchange_travel_accel = 5000
variable_adjusting_secondary_toolhead_focus_adjusts_zoffset = False
variable_cache_toolchange_travel_speed = 300
variable_cache_toolchange_travel_accel = 5000
variable_cache_toolchange_zhop = 1.0
variable_t0_toolhead_sensor_enabled = 0
variable_t1_toolhead_sensor_enabled = 0
variable_t0_bowden_sensor_enabled = 0
variable_t1_bowden_sensor_enabled = 0
variable_loaded_skew_profile = ""
variable_gcode_z_offset = 0.0
variable_start_x_offset = 0.0
variable_start_y_offset = 0.0
gcode = 
	_ECHO_VAOC_VARS
variable_expected_camera_x_position = 212.5
variable_expected_camera_y_position = 530.5

[gcode_macro _VAOC_START]
description = Called from the front end. If T0_TEMP, T1_TEMP and BED_TEMP parameter are specified, VAOC calibration will start under real conditions at printing temp.
gcode = 
	
	{% set t0_temp = params.T0_TEMP|default(0)|int %}
	{% set t1_temp = params.T1_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(0)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro SKEW_PROFILE"].loaded_profile|default("") %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=loaded_skew_profile VALUE='"{loaded_skew_profile}"'
	
	
	{% if t0_temp > 0 and t1_temp > 0 and bed_temp > 0 %}
	
	
	{% if not is_fixed %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("VAOC calibration at temp works only with a fixed installed VAOC device.") }
	{% endif %}
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE=0
	{% endif %}
	
	
	START_PRINT EXTRUDER_TEMP={t0_temp},{t1_temp} EXTRUDER_OTHER_LAYER_TEMP={t0_temp},{t1_temp} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp} INITIAL_TOOL=0 TOTAL_LAYER_COUNT=1 X0={(printable_x_max / 2 - 10)} Y0={(printable_y_max / 2 - 10)} X1={(printable_x_max / 2 + 10)} Y1={(printable_y_max / 2 + 10)} TOTAL_TOOLSHIFTS=1 FIRST_X={printable_x_max / 2} FIRST_Y={printable_y_max / 2} MIN_X={(printable_x_max / 2 - 10)} MAX_X={(printable_x_max / 2 + 10)} USED_TOOLS=0,1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=True
	
	{% endif %}
	
	
	_START_VAOC

[gcode_macro _START_VAOC]
description = Called from _VAOC_START. Do not call it manually.
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(printable_x_max/2)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(printable_y_max/2)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	DEBUG_ECHO PREFIX="VAOC_START" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, zcontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_x_offset VALUE={svv.idex_xoffset|default(0.0)|float}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_y_offset VALUE={svv.idex_yoffset|default(0.0)|float}
	
	
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_SAFE_Z_HEIGHT
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_speed VALUE={printer["gcode_macro RatOS"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_accel VALUE={printer["gcode_macro RatOS"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_zhop VALUE={printer["gcode_macro RatOS"].toolchange_zhop|float}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE=0
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"START X_REFERENCE:%.6f Y_REFERENCE:%.6f Z_REFERENCE:%.6f PARK_T0:%.6f PARK_T1:%.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, parking_position_t0, parking_position_t1)}
	
	
	_LED_VAOC_ON
	
	
	
	
	
	
	
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=gcode_z_offset VALUE={printer.gcode_move.homing_origin.z}
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z=0
	
	
	MAYBE_HOME
	M400
	
	
	_LOAD_RATOS_SKEW_PROFILE
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	IDEX_SINGLE
	{% endif %}
	
	
	
	SAVE_GCODE_STATE NAME=vaoc_state
	
	
	RESET_NAMED_OFFSET EVENT=reset_all
	
	
	{% if is_fixed %}
	_SELECT_TOOL T=0 TOOLSHIFT=false
	{% if default_toolhead == 0 %}
	G1 X{idex_xcontrolpoint} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint + safe_distance + additional_safe_distance} F{speed}
	{% else %}
	G1 X{idex_xcontrolpoint - safe_distance - additional_safe_distance} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint} F{speed}
	{% endif %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	{% else %}
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	G1 X{idex_xcontrolpoint} F{speed}
	G1 Y{idex_ycontrolpoint} F{speed}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	
	
	_SELECT_TOOL T={default_toolhead} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	{% if not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={default_toolhead}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=True

[gcode_macro _VAOC_END]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_y = printable_y_max / 2 %}
	{% set saved_gcode_z_offset = printer["gcode_macro _VAOC"].gcode_z_offset|default(0.0)|float %}
	
	DEBUG_ECHO PREFIX="_VAOC_END" MSG="printable_y_max: {printable_y_max}, center_y: {center_y}, safe_z: {safe_z}"
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% set x_offset_change = svv.idex_xoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_x_offset|default(0.0)|float %}
	{% set y_offset_change = svv.idex_yoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_y_offset|default(0.0)|float %}
	{% set offset_change_norm = (x_offset_change ** 2 + y_offset_change ** 2) ** 0.5 %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="VAOC calibration changed the relative XY offset between T0 and T1 by {offset_change_norm|round(3)} mm (ΔX: {x_offset_change|round(3)}, ΔY: {y_offset_change|round(3)})"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	G1 Y{center_y} F{speed}
	
	
	_IDEX_SINGLE INIT=1
	
	
	_LED_VAOC_OFF
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={printer["gcode_macro _VAOC"].cache_toolchange_zhop|float}
	
	
	{% if printer["gcode_macro _VAOC"].is_started_at_temp|default(true)|lower == 'true' %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_bowden_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_bowden_sensor_enabled|int}
	{% endif %}
	{% endif %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro _VAOC"].loaded_skew_profile|default("") %}
	{% if loaded_skew_profile != "" %}
	SKEW_PROFILE LOAD={loaded_skew_profile}
	{% else %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=vaoc_state
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z={saved_gcode_z_offset}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False

[gcode_macro _VAOC_LOAD_TOOL]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set auto_temp_offset = true if params.AUTO_TEMP_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set toolhead_zoffset = svv.idex_zoffset|default(0)|float %}
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move T%s to control point: X%.6f Y%.6f Z%.6f IS_FIXED=%s"' % (t, idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, is_fixed)}
	
	
	{% if not auto_temp_offset and not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={t}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	{% set current_z = printer.toolhead.position.z|float %}
	{% set lowest_toolhead_z = [current_z, current_z - toolhead_zoffset]|min %}
	{% if lowest_toolhead_z < safe_z %}
	G1 Z{[safe_z, safe_z + toolhead_zoffset]|max} F{z_speed}
	{% else %}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	{% endif %}
	
	
	_SELECT_TOOL T={t} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_SET_CAMERA_COOLING]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	
	
	{% set enable_camera_cooling = true if printer["gcode_macro _VAOC"].enable_camera_cooling|default(true)|lower == 'true' else false %}
	{% set camera_cooling_temperature = printer["gcode_macro _VAOC"].camera_cooling_temperature|float %}
	{% set camera_cooling_fan_speed = printer["gcode_macro _VAOC"].camera_cooling_fan_speed|float %}
	
	
	{% if printer.heater_bed.temperature >= camera_cooling_temperature and enable_camera_cooling %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={camera_cooling_fan_speed if t == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={camera_cooling_fan_speed if t == 1 else 0}
	
	
	M106.1 S{camera_cooling_fan_speed}
	
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	{% endif %}

[gcode_macro _VAOC_SET_TOOL]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="_VAOC_SET_TOOL" MSG="IDEX_MODE: {idex_mode}, TOOLHEAD: {toolhead}"
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	{% set x = printer.gcode_move.gcode_position.x|float %}
	{% set y = printer.gcode_move.gcode_position.y|float %}
	{% set z = printer.gcode_move.gcode_position.z|float %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE={x}
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE={y}
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE={z}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Control point was set: X%.6f Y%.6f Z%.6f"' % (x, y, z)}
	
	{% else %}
	
	
	
	{% set move_diff_x = printer.gcode_move.gcode_position.x|float - svv.idex_xcontrolpoint|float %}
	{% set move_diff_y = printer.gcode_move.gcode_position.y|float - svv.idex_ycontrolpoint|float %}
	{% set move_diff_z = printer.gcode_move.gcode_position.z|float - svv.idex_zcontrolpoint|float %}
	
	
	{% set new_x_offset = svv.idex_xoffset - move_diff_x %}
	{% set new_y_offset = svv.idex_yoffset - move_diff_y %}
	{% set new_z_offset = svv.idex_zoffset - move_diff_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE={new_x_offset}
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE={new_y_offset}
	
	{% set z_focus_msg = "" %}
	{% if move_diff_z|abs > 1e-6 %}
	{% if printer["gcode_macro _VAOC"].adjusting_secondary_toolhead_focus_adjusts_zoffset|default(false)|lower == 'true' %}
	{% set z_focus_msg = " (Z offset adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={new_z_offset}
	{% else %}
	{% set z_focus_msg = " (Z offset not adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	{% set new_z_offset = svv.idex_zoffset %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset was set: X%.6f Y%.6f Z%.6f%s"' % (toolhead, new_x_offset, new_y_offset, new_z_offset, z_focus_msg)}
	
	{% endif %}

[gcode_macro _VAOC_MOVE]
gcode = 
	
	{% set x = params.X|default(0)|float %}
	{% set y = params.Y|default(0)|float %}
	{% set z = params.Z|default(0)|float %}
	
	
	G91
	{% if z != 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 Z%.6f F300"' % (z)}
	G1 Z{z} F300
	
	{% else %}
	{% if x <=2 and y <=2 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 X%.6f Y%.6f F18000"' % (x, y)}
	G1 X{x} Y{y} F18000
	{% endif %}
	{% endif %}
	G90

[gcode_macro _VAOC_CALIBRATE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	{% if printer["z_offset_probe"] is defined and is_started %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	
	{% if auto_z_offset %}
	_START_VAOC AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_END
	{% else %}
	_VAOC_LOAD_TOOL T={default_toolhead}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	{% endif %}
	
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_Z_OFFSET
	
	{% endif %}

[gcode_macro _VAOC_PROBE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}
	{% if not auto_z_offset %}
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	{% endif %}
	M400
	_VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT

[gcode_macro _VAOC_Z_OFFSET_PROBE_CURRENT_POSITION]
gcode = 
	
	Z_OFFSET_PROBE PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_DROP=1 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median

[gcode_macro _VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT]
gcode = 
	{% if printer["z_offset_probe"] is defined %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE={last_z}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Z-offset control point set:: %.6f"' % last_z}
	
	{% else %}
	
	
	
	{% set z = svv.idex_zoffsetcontrolpoint|float - last_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={z}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-z)}
	
	
	G0 Z{svv.idex_zcontrolpoint|float} F{z_speed}
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset set: Z %.6f"' % (t, z)}
	
	{% endif %}
	
	{% endif %}

[gcode_macro _VAOC_ECHO_Z_OFFSET]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s toolhead z-offset %.6f"' % (1 if default_toolhead == 0 else 0, svv.idex_zoffset)}
	{% if svv.idex_zoffset|abs < 0.02 %}
	CONSOLE_ECHO TITLE={'"Perfect toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="You have a perfect toolhead z-offset!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.02 and svv.idex_zoffset|abs < 0.05 %}
	CONSOLE_ECHO TITLE={'"Good toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is good!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.05 and svv.idex_zoffset|abs < 0.1 %}
	CONSOLE_ECHO TITLE={'"High toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset could be better._N_Use minimum 0.3mm first layer height for copy and mirror mode prints." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.1 and svv.idex_zoffset|abs < 0.2 %}
	CONSOLE_ECHO TITLE={'"Bad toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is bad._N_Copy and mirror mode prints are not recommended with it." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.2 %}
	CONSOLE_ECHO TITLE={'"Unacceptable toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is unacceptable._N_Do not print in copy and mirror mode with it." TYPE="alert"
	{% endif %}
	RATOS_ECHO PREFIX="VAOC" MSG="Toolhead z-offset calibration done!"

[gcode_macro _VAOC_CALIBRATE_TEMP_OFFSET]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if is_fixed and is_started and printer["z_offset_probe"] is defined and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	_VAOC_LOAD_TOOL T={default_toolhead} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_NOZZLE_TEMP_OFFSETS
	
	{% endif %}

[gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET=0
	
	
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	M400

[gcode_macro _VAOC_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(150)|float %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Probing with nozzle temperature {temp}°C..."
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	
	
	G0 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _VAOC_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set msg = '"T0 expansion coefficient %.6fmm_N_T1 expansion coefficient %.6fmm"' % (svv.nozzle_expansion_coefficient_t0, svv.nozzle_expansion_coefficient_t1) %}
	CONSOLE_ECHO TITLE="Nozzle expansion coefficients:" MSG={msg} TYPE="success"

[gcode_macro _VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - expected_camera_x_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC x-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_xcontrolpoint, expected_camera_x_position)) }
	{% endif %}
	{% if (idex_ycontrolpoint - expected_camera_y_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC y-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_ycontrolpoint, expected_camera_y_position)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - printer.gcode_move.gcode_position.x|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected y-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_xcontrolpoint, printer.gcode_move.gcode_position.x|float)) }
	{% endif %}
	{% if (idex_ycontrolpoint - printer.gcode_move.gcode_position.y|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected x-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_ycontrolpoint, printer.gcode_move.gcode_position.y|float)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_SAFE_Z_HEIGHT]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set idex_zoffsetcontrolpoint = svv.idex_zoffsetcontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_SAFE_Z_HEIGHT" MSG={'"idex_zcontrolpoint: %.6f, idex_zoffsetcontrolpoint: %.6f"' % (idex_zcontrolpoint, idex_zoffsetcontrolpoint)}
	
	{% if safe_z < idex_zcontrolpoint + 2 or safe_z < idex_zoffsetcontrolpoint + 2 %}
	{action_raise_error("VAOC safe_z value (%.3f) is too low, it must be higher than %.3f" % (safe_z, [idex_zoffsetcontrolpoint + 2, idex_zcontrolpoint + 2]|max))}
	{% endif %}

[gcode_macro _VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED]
gcode = 
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T0. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T1. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_RESET]
gcode = 
	DEBUG_ECHO PREFIX="_VAOC_RESET" MSG="running template-emitted _VAOC_RESET macro"
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE=212.5
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE=530.5
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE=10
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE=0
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE=0.0
	
	RESET_DC_ENDSTOP_CONFIGURATION
	RESET_Y_MAX_ADJUSTMENT
	
	
	CONSOLE_ECHO TITLE="VAOC Configuration Reset" MSG="VAOC configuration has been reset. You must RESTART klipper for the changes to take effect,_N_then re-calibrate VAOC."

[gcode_macro _ECHO_VAOC_VARS]
description = Echo VAOC variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro _VAOC"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro _VAOC_SWITCH_LED]
gcode = 
	{% if params.STATE|default(0)|int == 1 %}
	_LED_VAOC_ON
	{% else %}
	_LED_VAOC_OFF
	{% endif %}

[gcode_macro Z_PROBE_TEST_T0]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T0
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST_T1]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T1
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	
	
	_VAOC_Z_PROBE_TEST_EVALUATE
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro _VAOC_Z_PROBE_LOOP]
gcode = 
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_SHAKE_IT
	_VAOC_START

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if primary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T0. Retried {primary_retries} time(s)."
	{% endif %}
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	
	{% if (primary_range - secondary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 is drifting significantly more than T1."
	{% endif %}
	{% if (secondary_range - primary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 is drifting significantly more than T0."
	{% endif %}
	
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T0]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T1]
gcode = 
	
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _SHAKE_IT]
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	_Z_HOP
	{% for i in range(3) %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 + 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 + 1}
	{% endfor %}
	{% for i in range(2) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 + 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 + 50}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 1}
	{% endfor %}
	{% endfor %}

[gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 retries updated: {new_retries}"

[gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 retries updated: {new_retries}"

[gcode_macro _CLEAR_PRIMARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _CLEAR_SECONDARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _VAOC_TEST_Z_OFFSET]
gcode = 
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}

[delayed_gcode _IDEX_INIT]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	VERIFY_HYBRID_INVERTED

[gcode_macro Z_TILT_ADJUST]
rename_existing = Z_TILT_ADJUST_ORIG
gcode = 
	
	{% set beacon_contact_z_tilt_adjust_samples = printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust_samples|default(2)|int %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(true)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	_IDEX_SINGLE
	
	_SELECT_TOOL T={printer["gcode_macro RatOS"].default_toolhead|default(0)|int} TOOLSHIFT=false
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_tilt_adjust %}
	Z_TILT_ADJUST_ORIG PROBE_METHOD=contact SAMPLES={beacon_contact_z_tilt_adjust_samples}
	{% else %}
	Z_TILT_ADJUST_ORIG
	{% endif %}
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if idex_mode == "copy" %}
	_IDEX_COPY
	{% elif idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[stepper_x]
position_max = 500
position_endstop = -59.6
position_min = -59.6
step_pin = PF13
dir_pin = x_dir_pin
enable_pin = !PF14
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t0:PA2

[stepper_y]
position_max = 533.65
position_min = -14.35
position_endstop = -14.35
step_pin = PG0
dir_pin = !y_dir_pin
enable_pin = !PF15
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = PG9

[stepper_z]
position_max = 500
position_min = -7
step_pin = PC13
dir_pin = !z0_dir_pin
enable_pin = !PF1
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4
homing_speed = 10
endstop_pin = probe:z_virtual_endstop

[z_tilt]
z_positions = 
	0,0
	250,500
	500,0
points = 
	20, 10
	480, 230
	20, 450
horizontal_move_z = 20
retries = 10
retry_tolerance = 0.02
speed = 600

[extruder]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t0:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t0:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t0:PD3
dir_pin = toolboard_t0:e_dir_pin
enable_pin = !toolboard_t0:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[firmware_retraction]
retract_speed = 60
unretract_extra_length = 0
unretract_speed = 60
retract_length = 0.2

[extruder1]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t1:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t1:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t1:PD3
dir_pin = toolboard_t1:e_dir_pin
enable_pin = !toolboard_t1:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[resonance_tester]
accel_chip_x = lis2dw toolboard_t0
accel_chip_y = lis2dw toolboard_t0
probe_points = 
	250,250,20

[tmc5160 stepper_x]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC4
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 dual_carriage]
stealthchop_threshold = 0
interpolate = True
cs_pin = PF2
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y]
stealthchop_threshold = 0
interpolate = True
cs_pin = PD11
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y1]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC7
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[stepper_y1]
step_pin = PG4
dir_pin = y1_dir_pin
enable_pin = !PA2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46

[tmc2209 stepper_z]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE4
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[tmc2209 stepper_z1]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE1
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z1]
step_pin = PE2
dir_pin = !z1_dir_pin
enable_pin = !PD4
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 stepper_z2]
stealthchop_threshold = 0
interpolate = True
uart_pin = PD3
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z2]
step_pin = PE6
dir_pin = !z2_dir_pin
enable_pin = !PE0
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 extruder]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t0:PB3
run_current = 0.707
sense_resistor = 0.11

[tmc2209 extruder1]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t1:PB3
run_current = 0.707
sense_resistor = 0.11

[beacon]
serial = /dev/beacon
x_offset = 0
y_offset = 27.5
mesh_main_direction = x
mesh_runs = 1
mesh_cluster_size = 0
speed = 15.
lift_speed = 80.
contact_max_hotend_temperature = 275
contact_mesh_min = 20,20
contact_mesh_max = 480,480

[beacon_user_z_offset]

[beacon_mesh]

[beacon_true_zero_correction]

[beacon_adaptive_heat_soak]

[delayed_gcode _BEACON_INIT]
initial_duration = 1
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	_BEACON_MESH_INIT
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_coefficient_multiplier
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_applied_offset
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=beacon_saved_runtime_offset
	{% if printer["gcode_macro RatOS"].beacon_contact_expansion_multiplier is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_contact_expansion_multiplier is no longer used, please remove it from your config file."
	{% endif %}
	{% if printer["gcode_macro RatOS"].beacon_scan_compensation_resolution is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_scan_compensation_resolution is no longer used, please remove it from your config file."
	{% endif %}

[gcode_macro BEACON_RATOS_CALIBRATION]
gcode = 
	RATOS_ECHO MSG="Did you mean BEACON_RATOS_CALIBRATE?"

[gcode_macro BEACON_RATOS_CALIBRATE]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	BEACON_INITIAL_CALIBRATION _AUTOMATED=True
	
	{% if beacon_contact_start_print_true_zero %}
	BEACON_POKE_TEST _AUTOMATED=True
	_BEACON_CHECK_POKE
	{% if printer["dual_carriage"] is not defined %}
	BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET _AUTOMATED=True
	{% endif %}
	{% endif %}
	
	{% set already_heated = False %}
	
	
	{% if beacon_contact_start_print_true_zero and beacon_scan_compensation_enable %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% set already_heated = True %}
	{% endif %}
	
	
	BEACON_FINAL_CALIBRATION _AUTOMATED=True _AUTOMATED_ALREADY_HEATED={already_heated} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	{% if beacon_contact_start_print_true_zero %}
	{% if printer["dual_carriage"] is not defined %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	_BEACON_ECHO_POKE
	{% endif %}
	RATOS_ECHO MSG="Beacon calibration finished!"
	
	
	_LED_BEACON_CALIBRATION_END
	
	
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG

[gcode_macro BEACON_INITIAL_CALIBRATION]
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Initial beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro BEACON_FINAL_CALIBRATION]
description = Runs BEACON_AUTO_CALIBRATE after heating the bed and chamber to specified temperatures. This creates a beacon model under reference conditions for future use.
	This macro will skip calibration if both the beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero settings are enabled, because a new
	model will be calibrated automatically at the start of each print. Use FORCE=True to override this check.
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set already_heated = true if params._AUTOMATED_ALREADY_HEATED|default(false)|lower == 'true' else false %}
	{% set force = params.FORCE|default('false')|lower in ('1', 'true', 'yes') %}
	
	
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default('false')|lower == "true" %}
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero and not force %}
	RATOS_ECHO MSG="BEACON_FINAL_CALIBRATION skipped, not needed because beacon_contact_calibrate_model_on_true_zero is enabled. Use FORCE=True to override."
	{% else %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	{% if chamber_temp > 0 and not already_heated %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	{% if not already_heated %}
	
	G0 Z2.5 F{z_hop_speed}
	
	
	RATOS_ECHO MSG="Waiting for calibration temperature..."
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	{% if beacon_adaptive_heat_soak %}
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,3600]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_Z_HOP
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Final beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	{% endif %}

[gcode_macro BEACON_POKE_TEST]
variable_poke_result_1 = -1
variable_poke_result_2 = -1
variable_poke_result_3 = -1
variable_poke_result_4 = -1
variable_poke_result_5 = -1
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_1 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_2 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_3 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_4 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_5 VALUE=-1
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G0 Z5 F{z_hop_speed}
	
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=1
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=2
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=3
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=4
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=5
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Beacon poke test finished!"
	{% if not automated %}
	_BEACON_ECHO_POKE
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro _BEACON_PROBE_POKE]
gcode = 
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	BEACON_POKE speed=3 top=5 bottom={poke_bottom}
	BEACON_QUERY

[gcode_macro _BEACON_STORE_POKE]
gcode = 
	
	{% set i = params.I|default(1)|int %}
	
	
	{% set last_z = printer.beacon.last_poke_result|default(0)|float %}
	
	
	{% if printer.beacon.last_poke_result|lower != "none" %}
	{% if printer.beacon.last_poke_result.error == 0 %}
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE={"poke_result_%s" % i} VALUE={printer.beacon.last_poke_result.latency}
	{% endif %}
	{% endif %}

[gcode_macro _BEACON_CHECK_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% if p1 == -1 or p2 == -1 or p3 == -1 or p4 == -1 or p5 == -1 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test error!") }
	{% endif %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	{% if avg > 6 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test failed!") }
	{% endif %}

[gcode_macro _BEACON_ECHO_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	
	
	{% if avg <= 1 %}
	{% set type = "success" %}
	{% set note = "Extremely low noise, rarely achieved" %}
	{% elif avg > 1 and avg <= 4 %}
	{% set type = "info" %}
	{% set note = "Excellent performance for a typical printer" %}
	{% elif avg > 4 and avg <= 8 %}
	{% set type = "warning" %}
	{% set note = "Acceptable performance, machine may have considerable cyclic axis noise" %}
	{% elif avg > 8 and avg <= 11 %}
	{% set type = "alert" %}
	{% set note = "Not ideal, may want to verify proper mounting or use thinner stackups" %}
	{% elif avg > 11 %}
	{% set type = "alert" %}
	{% set note = "Reason for concern, present setup may be risky to continue with" %}
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon poke test result:" TYPE={type} MSG={'"Average latency: %.2f_N_%s"' % (avg, note)}

[gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Nozzle temperature offset calibration..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET=0
	
	
	{% if not automated %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing with nozzle temperature {temp}°C..."
	PROBE PROBE_METHOD=contact PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median
	BEACON_QUERY
	
	
	G0 Z5 F{z_speed}

[gcode_macro _BEACON_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer.beacon.last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{default_toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% if default_toolhead == 0 %}
	CONSOLE_ECHO TYPE="info" MSG={'"T0 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t0}
	{% else %}
	CONSOLE_ECHO TYPE="info" MSG={'"T1 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t1}
	{% endif %}

[gcode_macro _BEACON_SET_NOZZLE_TEMP_OFFSET]
description = "Set the thermal expansion z offset for the active toolhead based on the current extruder target temperature and thermal expansion coefficient."
gcode = 
	{% if params.RESET is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The RESET parameter is no longer supported and has no effect."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% if params.TOOLHEAD is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The TOOLHEAD parameter is no longer supported and has no effect. The macro now automatically determines the current toolhead."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	{% if beacon_contact_expansion_compensation %}
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set nozzle_expansion_coefficient_t0 = svv.nozzle_expansion_coefficient_t0|default(0)|float %}
	{% if printer["dual_carriage"] is defined %}
	{% set nozzle_expansion_coefficient_t1 = svv.nozzle_expansion_coefficient_t1|default(0)|float %}
	{% endif %}
	
	
	{% set temp = printer['extruder' if toolhead == 0 else 'extruder1'].target|float %}
	
	
	{% set temp_delta = temp - beacon_contact_true_zero_temp %}
	{% set expansion_coefficient = nozzle_expansion_coefficient_t0 if toolhead == 0 else nozzle_expansion_coefficient_t1 %}
	{% set expansion_offset = temp_delta * (expansion_coefficient / 100) %}
	
	
	SET_NAMED_OFFSET NAME=hotend_thermal_expansion Z={expansion_offset} MOVE=1 MOVE_SPEED={z_speed}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG={'"Nozzle expansion offset of %.6fmm applied to T%s"' % (expansion_offset, toolhead)}
	DEBUG_ECHO PREFIX="_BEACON_SET_NOZZLE_TEMP_OFFSET" MSG="toolhead: {toolhead}, coefficient: {expansion_coefficient|round(6)}, temp_delta: {temp_delta|round(1)},  expansion_offset: {expansion_offset|round(6)}"
	
	{% endif %}

[gcode_macro BEACON_MEASURE_BEACON_OFFSET]
variable_needs_compensation = False
variable_reference_z = 0.0
variable_front = 0.0
variable_front_left = 0.0
variable_front_right = 0.0
variable_back = 0.0
variable_back_left = 0.0
variable_back_right = 0.0
variable_right = 0.0
variable_left = 0.0
variable_margin_x = 40
variable_margin_y = 40
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=False
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Measure beacon offset..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="center"
	
	
	G0 X{margin_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_left"
	
	
	G0 X{safe_home_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front"
	
	
	G0 X{(printable_x_max - margin_x)} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_right"
	
	
	G0 X{safe_home_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back"
	
	
	G0 X{margin_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_left"
	
	
	G0 X{margin_x} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="left"
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_BEACON_ECHO_BEACON_OFFSET
	
	
	_LED_BEACON_CALIBRATION_END
	
	{% endif %}

[gcode_macro _BEACON_STORE_BEACON_OFFSET]
gcode = 
	
	{% set location = params.LOCATION|lower %}
	
	
	{% set last_z = printer.beacon.last_offset_result["delta"]|default(0)|float %}
	
	
	{% if location == "center" %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE={location} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_BEACON_OFFSET]
gcode = 
	
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float * 1000 %}
	{% set front_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_left|default(0)|float * 1000 %}
	{% set front = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front|default(0)|float * 1000 %}
	{% set front_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_right|default(0)|float * 1000 %}
	{% set right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].right|default(0)|float * 1000 %}
	{% set back_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_right|default(0)|float * 1000 %}
	{% set back = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back|default(0)|float * 1000 %}
	{% set back_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_left|default(0)|float * 1000 %}
	{% set left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].left|default(0)|float * 1000 %}
	
	{% set line_1 = "Front left:    %.6fμm" % (front_left) %}
	{% set line_2 = "Front center:  %.6fμm" % (front) %}
	{% set line_3 = "Front right:   %.6fμm" % (front_right) %}
	{% set line_4 = "Left center:   %.6fμm" % (left) %}
	{% set line_5 = "Right center:  %.6fμm" % (right) %}
	{% set line_6 = "Back left:     %.6fμm" % (back_left) %}
	{% set line_7 = "Back center:   %.6fμm" % (back) %}
	{% set line_8 = "Back right:    %.6fμm" % (back_right) %}
	
	{% set max_value = [(front_left|abs), (front|abs), (front_right|abs), (left|abs), (right|abs), (back_left|abs), (back|abs), (back_right|abs)]|max %}
	{% if max_value <= 50 %}
	{% set type = "success" %}
	{% set recommendation = "Very low beacon offset: %.6fμm._N_No beacon scan compensation needed." % max_value %}
	{% elif max_value > 50 and max_value <= 100 %}
	{% set type = "info" %}
	{% set recommendation = "Low beacon offset: %.6fμm._N_You may experience first layer inconsistensies, consider beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 100 and max_value <= 150 %}
	{% set type = "warning" %}
	{% set recommendation = "High beacon offset: %.6fμm._N_High chance of first layer problems, beacon scan compensation is highly encouraged." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 150 and max_value <= 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Very High beacon offset: %.6fμm._N_You will encounter first layer problems on large prints unless you activate beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Extremely high beacon offset: %.6fμm._N_You have significant scan/contact inconsistency which is indicative of mechanical problems, please investigate before resorting to software compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon offset relative to the center" TYPE={type} MSG={'"_N_%s_N__N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s"' % (recommendation, line_1, line_2, line_3, line_4, line_5, line_6, line_7, line_8)}

[gcode_macro BEACON_CREATE_SCAN_COMPENSATION_MESH]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set profile = params.PROFILE|default("auto")|string %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set keep_temp_meshes = params.KEEP_TEMP_MESHES|default(0) %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' %}
	{% set desired_spacing = printer["gcode_macro RatOS"].beacon_scan_compensation_desired_spacing|float %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	
	{% if not beacon_scan_compensation_enable %}
	RATOS_ECHO MSG="Beacon scan compensation is disabled!"
	
	{% else %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	
	
	RATOS_ECHO MSG="Please wait..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	G1 Z2.5 F{z_speed}
	{% if beacon_adaptive_heat_soak %}
	
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,9000]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if not (beacon_adaptive_heat_soak or bed_heat_soak_time > 0) %}
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if printer.z_tilt is defined %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% endif %}
	{% if printer.quad_gantry_level is defined %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% endif %}
	
	
	_BEACON_CREATE_SCAN_COMPENSATION_MESH_CORE PROFILE="{profile}" DESIRED_SPACING={desired_spacing} CHAMBER_TEMP={chamber_temp} KEEP_TEMP_MESHES={keep_temp_meshes}
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	{% if automated %}
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon scan compensation mesh created!"
	
	
	{% if not automated %}
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED]
gcode = 
	
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED" MSG="beacon_scan_compensation_profile {beacon_scan_compensation_profile}, beacon_scan_compensation_enable {beacon_scan_compensation_enable}"
	
	{% if beacon_scan_compensation_enable %}
	BEACON_APPLY_SCAN_COMPENSATION PROFILE="{beacon_scan_compensation_profile}"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL]
gcode = 
	
	{% set beacon_contact_start_print_true_zero = params.BEACON_CONTACT_START_PRINT_TRUE_ZERO|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = params.beacon_contact_calibrate_model_on_true_zero|lower == 'true' %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and not printer.beacon.model %}
	{% set beacon_model_required_for_true_zero = beacon_contact_start_print_true_zero and not beacon_contact_calibrate_model_on_true_zero %}
	{% set beacon_model_required_for_homing =
	printer.fastconfig.settings.stepper_z.endstop_pin == 'probe:z_virtual_endstop'
	and (( printer.fastconfig.settings.beacon.home_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower != 'true')
	or ( printer.fastconfig.settings.beacon.default_probe_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower != 'true' )) %}
	{% if beacon_model_required_for_homing or beacon_model_required_for_true_zero %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("An active Beacon model is required. Have you performed initial Beacon calibration?") }
	{% endif %}
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION]
gcode = 
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set bed_temp_mismatch_is_error = true if printer["gcode_macro RatOS"].beacon_scan_compensation_bed_temp_mismatch_is_error|default(false)|lower == 'true' else false %}
	
	{% set bed_temp = params.BED_TEMP|default(0)|float %}
	{% if bed_temp == 0 %}
	{% set bed_temp = printer.heater_bed.temperature %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_PREFLIGHT_CHECK_BEACON" MSG="beacon_scan_compensation_profile={beacon_scan_compensation_profile}, beacon_scan_compensation_enable={beacon_scan_compensation_enable}, bed_temp={bed_temp}"
	
	{% if beacon_scan_compensation_enable %}
	_VALIDATE_COMPENSATION_MESH_PROFILE PROFILE="{beacon_scan_compensation_profile}" TITLE="Check Beacon scan compensation profile" SUBJECT="Configured compensation profile '{beacon_scan_compensation_profile}'" COMPARE_BED_TEMP={bed_temp} COMPARE_BED_TEMP_IS_ERROR={bed_temp_mismatch_is_error}
	{% endif %}

[gcode_macro _BEACON_MAYBE_SCAN_COMPENSATION]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set needs_scan_compensation = true if printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].needs_compensation|default(false)|lower == 'true' else false %}
	
	{% if needs_scan_compensation %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% endif %}

[gcode_macro _BEACON_HOME_AND_ABL]
gcode = 
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	{% if needs_rehoming %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}

[gcode_macro SAVE_Z_OFFSET]
description = Deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead, or in Mainsail use the SAVE button in the Z-OFFSET section.
gcode = 
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default('false')|lower == 'true' %}
	{% set msg = "SAVE_Z_OFFSET is deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead,_N_or in Mainsail use the SAVE button in the Z-OFFSET section."%}
	{% if not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% set msg = msg + "_N_You must then use the SAVE_CONFIG command to persist the change." %}
	{% endif %}
	CONSOLE_ECHO TYPE="error" MSG="{msg}"

[gcode_macro _BEACON_OFFSET_COMPARE]
gcode = 
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing..."
	
	
	BEACON_OFFSET_COMPARE SAMPLES_DROP=1 SAMPLES=3
	BEACON_QUERY

[fan]
pin = rpi:gpio4

[fan_generic part_fan_t0]
pin = PA8
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[fan_generic part_fan_t1]
pin = PE5
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[heater_fan toolhead_cooling_fan_t0]
heater = extruder
shutdown_speed = 1
pin = toolboard_t0:PB4

[heater_fan toolhead_cooling_fan_t1]
heater = extruder1
shutdown_speed = 1
pin = toolboard_t1:PB4

[controller_fan controller_fan]
pin = dinghy:PA4
tachometer_pin = dinghy:PC15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[z_offset_probe]
pin = ^PG10
z_offset = -7
y_offset = 0
x_offset = 37.5
speed = 10
samples = 3
sample_retract_dist = 5
lift_speed = 10.0
samples_result = median
samples_tolerance = 0.2
samples_tolerance_retries = 5

[neopixel vaoc_led]
pin = PB10
chain_count = 6
color_order = GRB

[heater_fan vaoc_fan]
pin = PD13
heater = heater_bed
fan_speed = 1.0
heater_temp = 50

[fan_generic filter]
pin = !PD14
enable_pin = PD15

[gcode_macro T0]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = True
variable_color = "7bff33"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = -32.6
variable_parking_position = -57.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=0 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[gcode_macro T1]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = False
variable_color = "0ea5e9"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = 532.6
variable_parking_position = 557.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=1 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[save_variables]
filename = /home/pi/printer_data/config/ratos-variables.cfg

[mcu dinghy]
serial = /dev/serial/by-id/usb-Klipper_stm32f072xb_Dragon_dinghy-if00

[temperature_sensor th0]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA0

[temperature_sensor th1]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA1

[temperature_sensor th2]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA2

[temperature_sensor th3]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA3

[controller_fan CTL2]
pin = dinghy:PB14
tachometer_pin = dinghy:PB15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[mcu plasma]
serial = /dev/serial/by-id/usb-Klipper_rp2040_Plasma-if00

[neopixel Chamber_Lights]
pin = plasma:gpio15
chain_count = 140
color_order = GRBW
initial_red = 0.0
initial_green = 0.0
initial_blue = 0.0
initial_white = 0.1

[beacon model default]
model_coef = 1.5287863993594841,
	1.9289099639750602,
	0.8838828622507556,
	0.25554883784260735,
	-0.015171504024913506,
	0.3044946127013882,
	0.15820427856566457,
	-0.25262403959326246,
	0.042488512846660914,
	0.16662470122520964
model_domain = 1.842634574664148e-07,1.9339206373083917e-07
model_range = 0.200000,5.000000
model_temp = 13.222247
model_offset = 0.00000

[bed_mesh default]
version = 1
points = 
	0.016163, 0.016713, 0.001923, -0.017658, -0.031574, -0.032498, -0.030898, -0.032177, -0.035213, -0.031148, -0.021322, -0.016924, -0.015012, -0.013911, -0.012197, -0.012583, -0.010489, -0.007529, -0.003986, -0.000980, 0.005518, 0.014442, 0.027426, 0.034677, 0.037410, 0.040391, 0.041842, 0.040369, 0.037615, 0.030776, 0.027664, 0.022856, 0.016892, 0.015398, 0.014717, 0.006921, 0.001532, 0.000731, 0.008657, 0.014036
	0.005356, -0.005066, -0.016998, -0.029668, -0.038334, -0.043672, -0.041139, -0.042488, -0.045199, -0.039432, -0.028746, -0.023642, -0.024058, -0.022802, -0.019679, -0.018514, -0.018102, -0.016476, -0.012722, -0.010077, -0.001809, 0.007180, 0.019853, 0.027754, 0.029964, 0.033626, 0.036783, 0.032018, 0.029372, 0.020847, 0.017634, 0.011926, 0.009013, 0.009254, 0.007972, -0.001380, -0.006940, -0.002160, 0.006135, 0.008330
	-0.004900, -0.006720, -0.021914, -0.039691, -0.050459, -0.050377, -0.046281, -0.048755, -0.054708, -0.051499, -0.033927, -0.027632, -0.030243, -0.031447, -0.024387, -0.021408, -0.020382, -0.018068, -0.015930, -0.013877, -0.006099, 0.003479, 0.013310, 0.024783, 0.025522, 0.030849, 0.033573, 0.031409, 0.025495, 0.016683, 0.011264, 0.008805, 0.006856, 0.008059, 0.007305, 0.002581, -0.003320, -0.003239, 0.004691, 0.010045
	-0.008791, -0.019334, -0.029149, -0.040533, -0.051698, -0.058235, -0.054863, -0.054840, -0.055692, -0.049534, -0.036731, -0.033053, -0.035667, -0.035315, -0.024352, -0.023825, -0.022538, -0.020438, -0.018207, -0.015389, -0.006515, 0.001966, 0.013591, 0.019434, 0.020600, 0.024967, 0.029425, 0.026812, 0.018980, 0.007878, 0.002360, 0.000859, 0.003849, 0.005649, 0.005421, -0.000416, -0.007906, -0.003164, 0.007582, 0.010039
	-0.018512, -0.018210, -0.033932, -0.050501, -0.061588, -0.064139, -0.060236, -0.062528, -0.067065, -0.062039, -0.045815, -0.039448, -0.040521, -0.042080, -0.033870, -0.030878, -0.027396, -0.024548, -0.021298, -0.020041, -0.011880, -0.002847, 0.008689, 0.015857, 0.015934, 0.018697, 0.022439, 0.022106, 0.017916, 0.005879, 0.001037, -0.001311, -0.001335, 0.001897, 0.003656, 0.000561, -0.006084, -0.005683, 0.000338, 0.006245
	-0.028558, -0.036721, -0.044680, -0.054969, -0.066140, -0.075045, -0.073515, -0.073161, -0.075696, -0.068963, -0.058892, -0.053111, -0.050990, -0.048040, -0.041262, -0.037419, -0.034866, -0.031845, -0.029787, -0.026524, -0.017896, -0.009322, -0.001010, 0.005819, 0.008058, 0.010456, 0.013266, 0.012529, 0.007992, -0.001491, -0.006769, -0.009303, -0.005980, -0.003567, -0.003340, -0.011496, -0.018818, -0.014808, -0.004181, -0.000733
	-0.037253, -0.038393, -0.053129, -0.066170, -0.075959, -0.079233, -0.077475, -0.082688, -0.086779, -0.083983, -0.069005, -0.062542, -0.060351, -0.058481, -0.051101, -0.043149, -0.039837, -0.037039, -0.034698, -0.031301, -0.024330, -0.019786, -0.010285, -0.001967, 0.002812, 0.004899, 0.009657, 0.006946, 0.002155, -0.005232, -0.009851, -0.011218, -0.011509, -0.010097, -0.010293, -0.013175, -0.018958, -0.019846, -0.012107, -0.005641
	-0.046584, -0.055590, -0.062606, -0.069218, -0.080399, -0.087414, -0.089037, -0.092376, -0.095115, -0.088957, -0.080802, -0.073290, -0.068741, -0.064591, -0.054452, -0.048270, -0.045916, -0.044559, -0.042047, -0.039605, -0.032667, -0.025789, -0.019495, -0.012773, -0.006697, -0.003025, 0.001413, 0.000817, -0.004738, -0.013008, -0.017605, -0.018191, -0.018524, -0.016356, -0.016750, -0.021992, -0.028943, -0.025791, -0.016146, -0.010447
	-0.051029, -0.051677, -0.068218, -0.079622, -0.088590, -0.089331, -0.089731, -0.096072, -0.105329, -0.100771, -0.087584, -0.079320, -0.075489, -0.072081, -0.064183, -0.054662, -0.048601, -0.049465, -0.047050, -0.045011, -0.040009, -0.032508, -0.025212, -0.018144, -0.011996, -0.008136, -0.003187, -0.003214, -0.006646, -0.013044, -0.019446, -0.020615, -0.022270, -0.021298, -0.020215, -0.020946, -0.026034, -0.026598, -0.021025, -0.012328
	-0.057184, -0.064908, -0.073093, -0.081584, -0.091971, -0.097048, -0.097688, -0.101869, -0.106651, -0.102162, -0.095658, -0.087938, -0.082718, -0.077017, -0.069608, -0.060682, -0.056889, -0.056864, -0.054260, -0.052011, -0.044563, -0.038927, -0.031943, -0.025832, -0.021170, -0.014319, -0.009046, -0.008543, -0.011751, -0.020287, -0.026608, -0.027259, -0.029120, -0.025549, -0.023221, -0.027725, -0.032477, -0.028427, -0.019343, -0.014932
	-0.060411, -0.062241, -0.080781, -0.090744, -0.100903, -0.099702, -0.098468, -0.104236, -0.116853, -0.112701, -0.102623, -0.095036, -0.091407, -0.089871, -0.079701, -0.070222, -0.064325, -0.063875, -0.062248, -0.059396, -0.052699, -0.047589, -0.041526, -0.028442, -0.024526, -0.019549, -0.015403, -0.014251, -0.017989, -0.022824, -0.027328, -0.029155, -0.033315, -0.032426, -0.027619, -0.030776, -0.033688, -0.032458, -0.027219, -0.019649
	-0.067541, -0.076514, -0.082321, -0.088656, -0.099968, -0.104930, -0.105875, -0.109051, -0.115531, -0.112996, -0.105760, -0.100390, -0.096171, -0.090011, -0.080050, -0.073632, -0.067451, -0.067031, -0.065225, -0.062471, -0.056370, -0.050129, -0.041626, -0.030801, -0.027579, -0.022472, -0.014826, -0.015306, -0.020316, -0.025953, -0.030661, -0.034103, -0.035502, -0.032738, -0.031311, -0.037314, -0.041306, -0.035280, -0.027449, -0.020395
	-0.068162, -0.069269, -0.088235, -0.096809, -0.103385, -0.103271, -0.102507, -0.109535, -0.123412, -0.118580, -0.106622, -0.099580, -0.097644, -0.096978, -0.087259, -0.077196, -0.068978, -0.067016, -0.063682, -0.062548, -0.057901, -0.052295, -0.044088, -0.032703, -0.026551, -0.021607, -0.014155, -0.013747, -0.017390, -0.022419, -0.027444, -0.030877, -0.033450, -0.032423, -0.032041, -0.033598, -0.035149, -0.034054, -0.029356, -0.020998
	-0.069473, -0.075924, -0.083569, -0.089648, -0.101235, -0.105828, -0.109144, -0.112613, -0.117233, -0.114186, -0.107090, -0.098616, -0.097084, -0.094257, -0.086773, -0.076409, -0.069532, -0.066472, -0.060956, -0.059191, -0.052886, -0.047752, -0.041275, -0.032437, -0.027780, -0.020398, -0.012061, -0.010133, -0.014056, -0.021528, -0.027924, -0.030605, -0.030609, -0.026068, -0.029346, -0.033991, -0.038254, -0.030610, -0.021109, -0.015885
	-0.068084, -0.066409, -0.083944, -0.094013, -0.102504, -0.105274, -0.106036, -0.112090, -0.121664, -0.117824, -0.104850, -0.097467, -0.098833, -0.098622, -0.089603, -0.078147, -0.068143, -0.066300, -0.061573, -0.057727, -0.054825, -0.048625, -0.040164, -0.030532, -0.025948, -0.020264, -0.014196, -0.010702, -0.013794, -0.019775, -0.026095, -0.028838, -0.030254, -0.027944, -0.027980, -0.030915, -0.032446, -0.028861, -0.023732, -0.014676
	-0.065280, -0.068669, -0.076948, -0.082397, -0.094986, -0.105117, -0.107099, -0.108954, -0.112557, -0.110326, -0.100725, -0.096325, -0.096240, -0.092388, -0.081185, -0.071682, -0.065650, -0.062250, -0.057027, -0.054691, -0.048349, -0.042069, -0.032712, -0.027728, -0.023396, -0.018458, -0.008357, -0.005699, -0.011447, -0.020033, -0.026387, -0.030280, -0.028443, -0.023735, -0.023838, -0.031580, -0.034204, -0.027768, -0.018029, -0.010628
	-0.061662, -0.057052, -0.075163, -0.086710, -0.094182, -0.097544, -0.098814, -0.105908, -0.114460, -0.111718, -0.097559, -0.091614, -0.093860, -0.093098, -0.081687, -0.069410, -0.064117, -0.062745, -0.055603, -0.051413, -0.048043, -0.040363, -0.031842, -0.023420, -0.017470, -0.012600, -0.008163, -0.003898, -0.007635, -0.013254, -0.019807, -0.025153, -0.027074, -0.023513, -0.023727, -0.028669, -0.029153, -0.024831, -0.018735, -0.009246
	-0.056176, -0.059439, -0.066501, -0.071527, -0.085216, -0.094918, -0.097595, -0.099419, -0.101847, -0.102015, -0.093849, -0.089867, -0.088840, -0.083167, -0.071832, -0.062522, -0.058023, -0.057771, -0.053050, -0.048285, -0.041374, -0.033527, -0.024473, -0.018428, -0.013958, -0.008161, -0.001196, 0.001754, -0.004016, -0.011132, -0.018325, -0.021813, -0.021514, -0.016948, -0.018061, -0.025702, -0.028671, -0.021470, -0.011028, -0.001934
	-0.059202, -0.050525, -0.065461, -0.076792, -0.084156, -0.088538, -0.090719, -0.096070, -0.105729, -0.105136, -0.090350, -0.083865, -0.087807, -0.086145, -0.074773, -0.064235, -0.057641, -0.055896, -0.051286, -0.046566, -0.042431, -0.034723, -0.023762, -0.014983, -0.009126, -0.004877, 0.000094, 0.003492, -0.000931, -0.005883, -0.011665, -0.015251, -0.016432, -0.016119, -0.015373, -0.018827, -0.019994, -0.017564, -0.012298, 0.002094
	-0.055561, -0.058184, -0.062669, -0.068111, -0.080741, -0.091895, -0.093911, -0.094387, -0.100239, -0.100695, -0.089841, -0.085682, -0.085212, -0.082910, -0.073072, -0.063594, -0.056157, -0.053482, -0.048107, -0.045405, -0.039982, -0.029777, -0.019905, -0.013872, -0.009732, -0.004272, 0.003500, 0.006909, 0.001302, -0.004626, -0.012374, -0.014751, -0.014637, -0.011794, -0.012913, -0.018244, -0.023377, -0.018086, -0.006575, 0.003294
	-0.062834, -0.047300, -0.060870, -0.073023, -0.079303, -0.082121, -0.083623, -0.091321, -0.100996, -0.098896, -0.085406, -0.078881, -0.081932, -0.082077, -0.074409, -0.063158, -0.053822, -0.050328, -0.045077, -0.039678, -0.035825, -0.028532, -0.017793, -0.009121, -0.003444, -0.000905, 0.003990, 0.007745, 0.004595, 0.000143, -0.004555, -0.007411, -0.010850, -0.010100, -0.010079, -0.013177, -0.016434, -0.014663, -0.010248, -0.000213
	-0.054748, -0.053907, -0.057576, -0.063118, -0.072478, -0.081366, -0.084424, -0.086348, -0.089718, -0.089305, -0.081771, -0.076889, -0.076923, -0.073518, -0.067973, -0.057643, -0.050848, -0.046966, -0.041560, -0.036436, -0.029233, -0.020685, -0.010240, -0.004935, -0.001084, 0.002478, 0.009168, 0.014038, 0.010885, 0.004752, -0.001650, -0.004209, -0.003998, -0.002336, -0.003784, -0.010930, -0.016480, -0.012798, -0.003650, 0.002998
	-0.059345, -0.041989, -0.057435, -0.068229, -0.072857, -0.072586, -0.075155, -0.083286, -0.091292, -0.089727, -0.073702, -0.068353, -0.072910, -0.073863, -0.065527, -0.053635, -0.046064, -0.043899, -0.037607, -0.031251, -0.026194, -0.018885, -0.008095, 0.000309, 0.004911, 0.007046, 0.010642, 0.015635, 0.015277, 0.012612, 0.008074, 0.004852, 0.001546, 0.000504, 0.000589, -0.002769, -0.006432, -0.007765, -0.005391, 0.006950
	-0.050324, -0.049088, -0.052417, -0.057257, -0.063818, -0.071057, -0.074636, -0.075459, -0.079445, -0.077368, -0.068788, -0.063940, -0.065040, -0.063419, -0.054864, -0.044910, -0.038774, -0.036951, -0.031149, -0.026080, -0.018383, -0.011985, -0.001732, 0.003893, 0.007180, 0.011120, 0.017429, 0.021738, 0.019167, 0.015812, 0.011027, 0.007243, 0.006720, 0.009346, 0.006598, -0.003776, -0.009199, -0.007592, 0.005481, 0.014396
	-0.058437, -0.035937, -0.050762, -0.060425, -0.061123, -0.059090, -0.062399, -0.072124, -0.080338, -0.074950, -0.060985, -0.054754, -0.059333, -0.060500, -0.051714, -0.038834, -0.031117, -0.031693, -0.025186, -0.017982, -0.014316, -0.010137, 0.000228, 0.008774, 0.014018, 0.016470, 0.019918, 0.022071, 0.021109, 0.019957, 0.018698, 0.015803, 0.013135, 0.011136, 0.008719, 0.003522, -0.000994, 0.000525, 0.006297, 0.018454
	-0.046143, -0.041577, -0.045391, -0.046668, -0.051722, -0.057607, -0.062802, -0.065205, -0.068243, -0.066293, -0.058216, -0.051324, -0.051806, -0.051018, -0.043393, -0.032431, -0.024016, -0.023321, -0.018504, -0.013897, -0.008455, -0.001123, 0.006609, 0.010462, 0.013887, 0.019328, 0.024804, 0.026590, 0.023420, 0.020337, 0.017129, 0.017199, 0.016391, 0.015616, 0.013257, 0.005832, -0.000019, 0.003462, 0.014308, 0.023624
	-0.051989, -0.030294, -0.043380, -0.051339, -0.050711, -0.048193, -0.052258, -0.061218, -0.070507, -0.068810, -0.049476, -0.042352, -0.046018, -0.046673, -0.038670, -0.027263, -0.018137, -0.018587, -0.013603, -0.008482, -0.004647, -0.000011, 0.008230, 0.015652, 0.019436, 0.023069, 0.024762, 0.027750, 0.028115, 0.026227, 0.022220, 0.023166, 0.020341, 0.018455, 0.014918, 0.011932, 0.007138, 0.008523, 0.014718, 0.026201
	-0.041448, -0.035286, -0.036538, -0.037577, -0.044652, -0.049300, -0.051092, -0.052841, -0.058068, -0.056947, -0.046235, -0.038436, -0.037494, -0.034175, -0.028932, -0.016904, -0.010075, -0.010552, -0.004464, -0.001243, 0.003236, 0.010200, 0.015604, 0.020362, 0.023157, 0.028023, 0.032826, 0.035958, 0.034819, 0.030600, 0.025988, 0.026013, 0.026284, 0.025661, 0.022322, 0.013336, 0.006464, 0.011312, 0.022330, 0.031668
	-0.048540, -0.022534, -0.035260, -0.042156, -0.042749, -0.037408, -0.038818, -0.047322, -0.056808, -0.053643, -0.035691, -0.027822, -0.028789, -0.028255, -0.020274, -0.007285, -0.000723, -0.000788, 0.005440, 0.008938, 0.008953, 0.012074, 0.017957, 0.025241, 0.029175, 0.032057, 0.033733, 0.038359, 0.039349, 0.037161, 0.034052, 0.034585, 0.032020, 0.029940, 0.026326, 0.024577, 0.020432, 0.021586, 0.024568, 0.034552
	-0.033086, -0.027982, -0.029443, -0.029011, -0.035629, -0.040579, -0.038290, -0.037389, -0.041260, -0.040430, -0.032279, -0.021394, -0.018817, -0.015525, -0.007558, 0.006345, 0.011048, 0.011271, 0.013497, 0.017030, 0.017449, 0.022752, 0.026764, 0.030722, 0.033532, 0.037203, 0.043356, 0.048536, 0.047776, 0.043851, 0.039311, 0.039944, 0.039954, 0.038931, 0.034893, 0.030946, 0.023127, 0.027359, 0.034859, 0.043920
	-0.036218, -0.016846, -0.030897, -0.036980, -0.037261, -0.033334, -0.030888, -0.034074, -0.042142, -0.039980, -0.021377, -0.013603, -0.014171, -0.013131, -0.001768, 0.014998, 0.020060, 0.018173, 0.019934, 0.024704, 0.023739, 0.024617, 0.027288, 0.035116, 0.041187, 0.043128, 0.045921, 0.051709, 0.053031, 0.050698, 0.047697, 0.047728, 0.046845, 0.043201, 0.041805, 0.040728, 0.036184, 0.034435, 0.035120, 0.045329
	-0.029808, -0.023871, -0.026541, -0.026705, -0.031203, -0.036908, -0.034411, -0.029231, -0.028090, -0.026102, -0.016691, -0.007747, -0.004471, 0.001560, 0.010738, 0.025062, 0.027672, 0.024833, 0.026976, 0.029502, 0.030754, 0.035709, 0.039403, 0.044719, 0.046379, 0.049250, 0.054178, 0.059793, 0.059542, 0.052111, 0.047608, 0.050103, 0.053142, 0.052747, 0.050045, 0.044102, 0.033149, 0.035392, 0.045678, 0.054080
	-0.032238, -0.008993, -0.023999, -0.030969, -0.028658, -0.024887, -0.024493, -0.028088, -0.031053, -0.022849, -0.003868, 0.004647, 0.004540, 0.007560, 0.018373, 0.031401, 0.035778, 0.033768, 0.035173, 0.035884, 0.036597, 0.038940, 0.044566, 0.053914, 0.056554, 0.056382, 0.056449, 0.060387, 0.062696, 0.058223, 0.055016, 0.056193, 0.056891, 0.052793, 0.052741, 0.052626, 0.048117, 0.045032, 0.048033, 0.055100
	-0.019758, -0.015110, -0.017814, -0.018871, -0.023340, -0.028653, -0.026880, -0.018681, -0.017020, -0.011343, -0.001002, 0.008249, 0.014012, 0.020367, 0.026878, 0.038534, 0.041827, 0.039532, 0.039775, 0.039109, 0.043172, 0.049325, 0.056604, 0.059583, 0.059329, 0.059876, 0.062766, 0.068759, 0.067214, 0.059657, 0.055950, 0.056798, 0.058619, 0.058591, 0.059849, 0.056473, 0.046841, 0.047921, 0.058342, 0.065346
	-0.018628, -0.000296, -0.014764, -0.022634, -0.020483, -0.016362, -0.015485, -0.017352, -0.020246, -0.010362, 0.008635, 0.018414, 0.018542, 0.024258, 0.033370, 0.045728, 0.049983, 0.044610, 0.044638, 0.047649, 0.049220, 0.051954, 0.058932, 0.065915, 0.069102, 0.067410, 0.067680, 0.073734, 0.072203, 0.067293, 0.063945, 0.064378, 0.065047, 0.061989, 0.062882, 0.063468, 0.059707, 0.057986, 0.059739, 0.066139
	-0.010091, -0.006551, -0.008018, -0.009589, -0.016068, -0.020662, -0.019451, -0.010985, -0.009391, -0.003580, 0.007826, 0.019598, 0.024961, 0.033762, 0.040618, 0.050868, 0.052139, 0.050495, 0.049198, 0.051777, 0.056840, 0.061771, 0.068414, 0.072295, 0.073443, 0.072145, 0.073414, 0.079338, 0.075988, 0.067367, 0.064745, 0.064435, 0.066982, 0.065811, 0.067424, 0.063230, 0.058438, 0.059982, 0.067672, 0.072460
	-0.016254, 0.006291, -0.008031, -0.013944, -0.014475, -0.010741, -0.009932, -0.011709, -0.015503, -0.006971, 0.013190, 0.024865, 0.029121, 0.033942, 0.044335, 0.054572, 0.058078, 0.055224, 0.055897, 0.058327, 0.061207, 0.063939, 0.070506, 0.078141, 0.084203, 0.081223, 0.079519, 0.082883, 0.080890, 0.076174, 0.071279, 0.073064, 0.071225, 0.066859, 0.069860, 0.070836, 0.069427, 0.069140, 0.070950, 0.075269
	-0.008127, 0.000730, 0.001164, -0.000308, -0.006659, -0.012343, -0.011463, -0.003755, -0.001876, 0.005166, 0.016616, 0.030243, 0.036509, 0.045020, 0.053681, 0.063738, 0.066425, 0.063964, 0.062796, 0.065633, 0.071912, 0.077280, 0.082580, 0.086477, 0.089798, 0.089603, 0.091453, 0.096125, 0.088708, 0.079903, 0.074317, 0.076190, 0.075399, 0.075242, 0.079628, 0.077855, 0.071473, 0.073702, 0.082757, 0.088086
	-0.010951, 0.013218, -0.000878, -0.006241, -0.005623, 0.000046, 0.000158, -0.002943, -0.005314, 0.005491, 0.026890, 0.035754, 0.041490, 0.045829, 0.059325, 0.070249, 0.074114, 0.071815, 0.073229, 0.076313, 0.080778, 0.081554, 0.087919, 0.096206, 0.101562, 0.101674, 0.100494, 0.103989, 0.100292, 0.093977, 0.088080, 0.088136, 0.086555, 0.081494, 0.084966, 0.087073, 0.084113, 0.085184, 0.087700, 0.092188
	-0.002972, 0.006020, 0.006098, 0.004303, 0.001326, -0.002386, -0.001840, 0.005325, 0.008624, 0.016246, 0.026781, 0.039696, 0.048540, 0.055938, 0.066982, 0.076497, 0.080828, 0.079669, 0.080127, 0.083754, 0.089783, 0.093456, 0.100570, 0.105322, 0.107132, 0.110571, 0.113141, 0.118064, 0.111721, 0.101634, 0.093555, 0.093112, 0.093104, 0.092325, 0.094780, 0.092552, 0.085283, 0.088882, 0.097508, 0.105280
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 11.4
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Preperations]
version = 1
points = 
	0.012158, -0.006098, -0.020628, -0.034069, -0.049418, -0.058491, -0.062706, -0.063181, -0.065552, -0.063461, -0.057373, -0.056717, -0.056579, -0.054080, -0.053373, -0.056878, -0.057281, -0.055224, -0.049676, -0.047605, -0.041454, -0.034605, -0.022490, -0.011292, -0.009411, -0.005344, -0.003510, -0.002717, -0.005999, -0.010712, -0.013141, -0.015611, -0.020004, -0.017667, -0.016629, -0.022248, -0.024864, -0.024065, -0.014921, -0.010826
	-0.005958, -0.021084, -0.033800, -0.047903, -0.059950, -0.071345, -0.072502, -0.073350, -0.075852, -0.072963, -0.067236, -0.064315, -0.065698, -0.064338, -0.062871, -0.065238, -0.067095, -0.063584, -0.059241, -0.057846, -0.051380, -0.043157, -0.030230, -0.019950, -0.018121, -0.014291, -0.009354, -0.013065, -0.016464, -0.022925, -0.025337, -0.026541, -0.030577, -0.029068, -0.027094, -0.030532, -0.034241, -0.032625, -0.021498, -0.020513
	-0.017526, -0.027763, -0.040710, -0.055305, -0.068172, -0.079641, -0.081247, -0.081903, -0.083679, -0.081855, -0.073270, -0.070340, -0.072083, -0.071536, -0.066055, -0.065901, -0.069085, -0.066531, -0.063284, -0.061616, -0.053366, -0.047292, -0.035451, -0.023167, -0.022205, -0.016699, -0.012552, -0.014153, -0.018802, -0.030443, -0.032210, -0.034051, -0.034437, -0.031439, -0.030406, -0.032817, -0.036351, -0.034849, -0.024250, -0.019489
	-0.017750, -0.030284, -0.043463, -0.055839, -0.071865, -0.084888, -0.086157, -0.084619, -0.086681, -0.084515, -0.075246, -0.073263, -0.075604, -0.075123, -0.069177, -0.070723, -0.071097, -0.068644, -0.065465, -0.063718, -0.057574, -0.049335, -0.036556, -0.028418, -0.028259, -0.023387, -0.018454, -0.020519, -0.027499, -0.038314, -0.041534, -0.041886, -0.039972, -0.036438, -0.033959, -0.033009, -0.038291, -0.036339, -0.022688, -0.024783
	-0.021354, -0.034103, -0.047541, -0.060551, -0.075691, -0.089373, -0.092241, -0.091621, -0.093203, -0.090723, -0.082480, -0.079781, -0.079706, -0.079674, -0.074365, -0.073780, -0.073465, -0.070165, -0.064970, -0.065503, -0.059104, -0.051038, -0.041817, -0.031243, -0.031386, -0.028837, -0.023658, -0.024237, -0.029641, -0.039210, -0.042766, -0.044461, -0.041863, -0.039075, -0.034881, -0.034571, -0.039386, -0.038253, -0.031659, -0.024202
	-0.027696, -0.041184, -0.054054, -0.064759, -0.080898, -0.094964, -0.097906, -0.098033, -0.101256, -0.098300, -0.091517, -0.088420, -0.086945, -0.085220, -0.079938, -0.079979, -0.079828, -0.074842, -0.072903, -0.072415, -0.065384, -0.057454, -0.048482, -0.040977, -0.039336, -0.036065, -0.032553, -0.034336, -0.039337, -0.046271, -0.049398, -0.051220, -0.049530, -0.045000, -0.045029, -0.042100, -0.049767, -0.046386, -0.035574, -0.032188
	-0.033426, -0.046259, -0.059363, -0.068024, -0.084858, -0.097009, -0.103434, -0.106215, -0.107319, -0.106178, -0.100333, -0.097536, -0.095352, -0.091322, -0.086332, -0.082309, -0.081440, -0.078413, -0.075067, -0.073134, -0.068255, -0.062667, -0.054300, -0.046004, -0.042001, -0.039181, -0.035010, -0.036092, -0.041599, -0.048788, -0.051751, -0.051179, -0.051019, -0.049121, -0.045860, -0.046756, -0.050005, -0.051613, -0.040237, -0.035349
	-0.037931, -0.051993, -0.066455, -0.075044, -0.088177, -0.102890, -0.108223, -0.112373, -0.115787, -0.113421, -0.108543, -0.105936, -0.101048, -0.096863, -0.090726, -0.087882, -0.086665, -0.083874, -0.081096, -0.080894, -0.075125, -0.071038, -0.063072, -0.054696, -0.051039, -0.046728, -0.042566, -0.043887, -0.048745, -0.056834, -0.059808, -0.060521, -0.060664, -0.057968, -0.056317, -0.052477, -0.058814, -0.055877, -0.046325, -0.042545
	-0.041429, -0.053634, -0.067633, -0.077111, -0.090998, -0.103561, -0.109445, -0.114741, -0.120075, -0.119821, -0.114703, -0.110411, -0.105589, -0.099826, -0.093730, -0.089705, -0.087199, -0.086439, -0.082688, -0.082221, -0.078348, -0.073203, -0.065273, -0.058731, -0.054025, -0.049231, -0.044830, -0.043830, -0.045839, -0.054137, -0.059075, -0.059515, -0.058546, -0.056956, -0.054145, -0.053129, -0.056587, -0.056341, -0.047057, -0.039936
	-0.044295, -0.058972, -0.072101, -0.082726, -0.095001, -0.106449, -0.111505, -0.118363, -0.124608, -0.123506, -0.120263, -0.115400, -0.110227, -0.104535, -0.100348, -0.095757, -0.092961, -0.092377, -0.089613, -0.088047, -0.084834, -0.079314, -0.072500, -0.064519, -0.060449, -0.055767, -0.051803, -0.050997, -0.052855, -0.058115, -0.063348, -0.065363, -0.067936, -0.063474, -0.061475, -0.054726, -0.062529, -0.055352, -0.048878, -0.044991
	-0.045804, -0.056574, -0.073308, -0.082450, -0.097495, -0.107467, -0.111501, -0.116418, -0.126724, -0.125980, -0.123231, -0.120494, -0.114667, -0.111289, -0.103451, -0.099228, -0.095880, -0.095882, -0.093328, -0.091000, -0.087051, -0.081909, -0.075949, -0.064971, -0.061050, -0.055137, -0.049046, -0.047319, -0.049806, -0.056968, -0.059608, -0.060249, -0.063032, -0.060556, -0.056284, -0.056263, -0.058891, -0.057890, -0.051554, -0.042382
	-0.049818, -0.062681, -0.076305, -0.084328, -0.098717, -0.107866, -0.113937, -0.120088, -0.128622, -0.128931, -0.126353, -0.123191, -0.118529, -0.115642, -0.106288, -0.103976, -0.099708, -0.097750, -0.094501, -0.094545, -0.090910, -0.085952, -0.077352, -0.067196, -0.062435, -0.057738, -0.052934, -0.051098, -0.055294, -0.061112, -0.063120, -0.067525, -0.067979, -0.066558, -0.064608, -0.060597, -0.067812, -0.057641, -0.056224, -0.046471
	-0.050591, -0.060432, -0.075602, -0.083877, -0.096933, -0.106147, -0.112334, -0.118295, -0.127966, -0.128757, -0.125157, -0.121831, -0.118557, -0.116124, -0.108723, -0.104502, -0.099469, -0.095841, -0.090662, -0.089822, -0.087969, -0.084545, -0.076375, -0.064821, -0.059093, -0.053427, -0.047372, -0.044341, -0.047964, -0.054064, -0.057133, -0.059152, -0.061568, -0.059109, -0.056640, -0.056691, -0.056844, -0.054564, -0.048514, -0.040641
	-0.047704, -0.059564, -0.073127, -0.080945, -0.093764, -0.105483, -0.111501, -0.118792, -0.124812, -0.126576, -0.122064, -0.118087, -0.116126, -0.114867, -0.108053, -0.103336, -0.097558, -0.093250, -0.086537, -0.085303, -0.083677, -0.079292, -0.070542, -0.062526, -0.056818, -0.052534, -0.044035, -0.041353, -0.046942, -0.051329, -0.055481, -0.062777, -0.058499, -0.058025, -0.057390, -0.053562, -0.060843, -0.046555, -0.046260, -0.036083
	-0.046496, -0.052983, -0.067518, -0.076904, -0.091704, -0.103105, -0.111995, -0.117751, -0.122307, -0.122941, -0.118230, -0.115004, -0.114258, -0.113138, -0.105515, -0.098417, -0.093384, -0.090070, -0.083281, -0.079846, -0.078725, -0.075452, -0.066225, -0.057269, -0.053103, -0.047808, -0.039772, -0.036834, -0.041270, -0.047376, -0.051111, -0.053848, -0.053029, -0.050301, -0.048919, -0.050775, -0.050121, -0.046842, -0.039633, -0.030497
	-0.040695, -0.051685, -0.064038, -0.070974, -0.086679, -0.101773, -0.109889, -0.114373, -0.117883, -0.118764, -0.113125, -0.110931, -0.111099, -0.109664, -0.098733, -0.093182, -0.090154, -0.086213, -0.077214, -0.077108, -0.075555, -0.069117, -0.060704, -0.054093, -0.049253, -0.044799, -0.037536, -0.035304, -0.040134, -0.045456, -0.051720, -0.056675, -0.053743, -0.052923, -0.049701, -0.050238, -0.056776, -0.041485, -0.041755, -0.027329
	-0.039842, -0.039428, -0.055732, -0.063890, -0.079179, -0.092823, -0.101698, -0.106156, -0.111709, -0.113152, -0.108033, -0.104872, -0.105645, -0.103501, -0.094487, -0.087264, -0.084273, -0.080950, -0.074116, -0.070973, -0.068409, -0.062825, -0.054757, -0.044150, -0.040620, -0.036602, -0.031538, -0.026478, -0.031123, -0.037600, -0.042341, -0.046700, -0.047380, -0.042880, -0.040967, -0.045367, -0.044192, -0.038553, -0.029948, -0.020790
	-0.030596, -0.038279, -0.051528, -0.058981, -0.073983, -0.089044, -0.099173, -0.101740, -0.104830, -0.107083, -0.102306, -0.101554, -0.101336, -0.097146, -0.089217, -0.083800, -0.080621, -0.078071, -0.071535, -0.068328, -0.065806, -0.056882, -0.048683, -0.039756, -0.036349, -0.031328, -0.025351, -0.024133, -0.029773, -0.033858, -0.040011, -0.044146, -0.043900, -0.044797, -0.038019, -0.042319, -0.047297, -0.031851, -0.034318, -0.013527
	-0.032121, -0.034722, -0.047839, -0.054710, -0.069175, -0.084213, -0.094533, -0.097233, -0.100863, -0.104775, -0.099781, -0.097416, -0.098804, -0.096059, -0.086694, -0.079692, -0.076749, -0.074609, -0.068106, -0.063906, -0.061136, -0.055447, -0.045559, -0.035389, -0.029696, -0.025708, -0.020034, -0.017335, -0.022665, -0.028532, -0.032369, -0.035760, -0.037212, -0.035201, -0.032872, -0.034132, -0.035907, -0.032127, -0.025026, -0.009282
	-0.026707, -0.034374, -0.045183, -0.052691, -0.067014, -0.084964, -0.092286, -0.094441, -0.099291, -0.103609, -0.098278, -0.094972, -0.097169, -0.095394, -0.086653, -0.080205, -0.076284, -0.070594, -0.064535, -0.062012, -0.060174, -0.051216, -0.040622, -0.033396, -0.029636, -0.024235, -0.017274, -0.018232, -0.021459, -0.024778, -0.031754, -0.034481, -0.033398, -0.037949, -0.030432, -0.033219, -0.038432, -0.021975, -0.030052, -0.009295
	-0.028559, -0.029280, -0.042071, -0.048655, -0.061603, -0.076257, -0.086817, -0.091815, -0.095682, -0.098682, -0.093729, -0.091168, -0.092213, -0.090073, -0.084070, -0.077048, -0.072045, -0.066267, -0.060309, -0.053639, -0.051696, -0.046852, -0.034069, -0.025602, -0.020640, -0.018021, -0.013180, -0.009049, -0.013846, -0.018012, -0.021061, -0.024515, -0.027068, -0.026804, -0.024283, -0.025595, -0.028234, -0.025272, -0.019246, -0.008595
	-0.025711, -0.029003, -0.038836, -0.048015, -0.058511, -0.074480, -0.083738, -0.087945, -0.091439, -0.094310, -0.090288, -0.087858, -0.088589, -0.086163, -0.081829, -0.075146, -0.071136, -0.064399, -0.057338, -0.052103, -0.049650, -0.043210, -0.032998, -0.023124, -0.020191, -0.016625, -0.012433, -0.010465, -0.009871, -0.015007, -0.021217, -0.021582, -0.023800, -0.027652, -0.021527, -0.027137, -0.030828, -0.020152, -0.026202, -0.008568
	-0.031287, -0.022523, -0.035800, -0.041583, -0.052691, -0.065901, -0.075941, -0.079246, -0.083936, -0.086778, -0.082235, -0.078893, -0.080642, -0.079419, -0.074324, -0.067418, -0.062113, -0.057744, -0.049923, -0.043390, -0.040055, -0.035512, -0.023838, -0.015485, -0.009895, -0.008346, -0.005387, 0.001467, -0.000104, -0.003777, -0.007926, -0.012023, -0.013970, -0.014207, -0.013994, -0.017009, -0.019233, -0.019282, -0.014210, -0.001146
	-0.020719, -0.024043, -0.035160, -0.041635, -0.051902, -0.063884, -0.072884, -0.076738, -0.081856, -0.083761, -0.077857, -0.074651, -0.077952, -0.076310, -0.069721, -0.063240, -0.056775, -0.055188, -0.046711, -0.042996, -0.039499, -0.032268, -0.023129, -0.015735, -0.012305, -0.009383, -0.005789, -0.001996, -0.001166, -0.005106, -0.009634, -0.009864, -0.011905, -0.015913, -0.010246, -0.016645, -0.022975, -0.011972, -0.018524, 0.001048
	-0.026050, -0.019774, -0.032555, -0.037813, -0.044657, -0.054435, -0.065271, -0.071019, -0.075585, -0.077479, -0.072635, -0.069526, -0.071046, -0.070770, -0.063085, -0.055960, -0.050956, -0.049593, -0.042773, -0.034996, -0.032645, -0.029030, -0.020343, -0.011008, -0.005751, -0.003252, 0.000746, 0.003215, 0.001749, -0.000068, -0.001413, -0.002608, -0.005837, -0.007103, -0.008431, -0.012027, -0.015656, -0.014417, -0.006321, 0.003748
	-0.021728, -0.019178, -0.031232, -0.036249, -0.042206, -0.053190, -0.064017, -0.068545, -0.074597, -0.074544, -0.069543, -0.065779, -0.067928, -0.067354, -0.060655, -0.052790, -0.047723, -0.046044, -0.038188, -0.034539, -0.032080, -0.027152, -0.018902, -0.012508, -0.009304, -0.003955, -0.000288, -0.001549, -0.000556, -0.003756, -0.008467, -0.003851, -0.005999, -0.012959, -0.007423, -0.015332, -0.017388, -0.005695, -0.010807, 0.007710
	-0.028204, -0.017096, -0.027984, -0.032129, -0.038374, -0.046561, -0.059356, -0.061847, -0.069228, -0.070551, -0.065474, -0.059719, -0.059893, -0.060271, -0.053666, -0.047202, -0.041189, -0.039979, -0.033189, -0.028761, -0.025714, -0.021660, -0.014905, -0.007841, -0.004669, -0.001174, 0.001874, 0.005613, 0.005527, 0.001504, -0.000694, 0.001892, 0.001885, -0.002506, -0.005619, -0.007166, -0.009935, -0.007406, 0.000545, 0.009983
	-0.019393, -0.017785, -0.025482, -0.028146, -0.036861, -0.047528, -0.055696, -0.059118, -0.064151, -0.066346, -0.060565, -0.055661, -0.055495, -0.051944, -0.048147, -0.040645, -0.036359, -0.035990, -0.026764, -0.024843, -0.023572, -0.019648, -0.013807, -0.006811, -0.004589, -0.000266, 0.003010, 0.004931, 0.006834, 0.003254, -0.001690, 0.003120, 0.001036, -0.005283, 0.000659, -0.007399, -0.010996, -0.000832, -0.006381, 0.012135
	-0.021519, -0.010062, -0.018662, -0.023011, -0.029067, -0.036961, -0.043194, -0.048197, -0.053632, -0.055489, -0.050054, -0.045247, -0.042655, -0.040243, -0.034315, -0.027094, -0.022697, -0.021644, -0.015333, -0.010768, -0.013712, -0.012051, -0.005326, 0.000560, 0.005300, 0.007429, 0.009930, 0.015968, 0.016454, 0.012383, 0.010385, 0.011612, 0.011413, 0.008357, 0.006831, 0.005524, 0.003087, 0.003507, 0.009876, 0.018892
	-0.017331, -0.015238, -0.021971, -0.024651, -0.029507, -0.040209, -0.044232, -0.046101, -0.052689, -0.053151, -0.047133, -0.042985, -0.040475, -0.037020, -0.029999, -0.021348, -0.018232, -0.017876, -0.013058, -0.008535, -0.013279, -0.011527, -0.006296, -0.001615, 0.002270, 0.006991, 0.010272, 0.013407, 0.015950, 0.012503, 0.008026, 0.013701, 0.011513, 0.004867, 0.010667, 0.006774, 0.003571, 0.012416, 0.004875, 0.020961
	-0.022637, -0.011107, -0.018340, -0.023896, -0.028320, -0.038092, -0.041212, -0.041642, -0.044537, -0.046015, -0.041699, -0.035805, -0.033527, -0.030911, -0.022925, -0.010175, -0.007279, -0.008644, -0.005065, -0.000597, -0.003797, -0.004052, 0.000635, 0.006175, 0.010857, 0.012993, 0.016956, 0.022765, 0.023298, 0.020262, 0.018285, 0.019467, 0.021161, 0.018785, 0.017891, 0.017817, 0.013874, 0.012825, 0.015904, 0.025844
	-0.014532, -0.010189, -0.019385, -0.022584, -0.028159, -0.037803, -0.040566, -0.038125, -0.040339, -0.038899, -0.033171, -0.028143, -0.025641, -0.019755, -0.012463, -0.003824, -0.000871, -0.002698, -0.000197, 0.001952, -0.001353, -0.000188, 0.004902, 0.012600, 0.014373, 0.016449, 0.018872, 0.022822, 0.026385, 0.020681, 0.015275, 0.021387, 0.023535, 0.016733, 0.022161, 0.018819, 0.011276, 0.020785, 0.014683, 0.032409
	-0.016972, -0.004835, -0.015539, -0.019706, -0.022971, -0.032222, -0.037732, -0.035551, -0.033892, -0.031679, -0.024624, -0.019946, -0.016412, -0.010040, -0.003445, 0.005991, 0.008364, 0.006410, 0.008289, 0.009260, 0.007409, 0.008691, 0.015230, 0.022729, 0.025465, 0.025502, 0.026102, 0.030309, 0.031861, 0.026963, 0.024651, 0.027000, 0.029039, 0.025577, 0.027217, 0.027660, 0.023245, 0.021705, 0.026383, 0.034120
	-0.007042, -0.003943, -0.013314, -0.016082, -0.020497, -0.030911, -0.035096, -0.030889, -0.029351, -0.025337, -0.018980, -0.012449, -0.008879, -0.001902, 0.003577, 0.011256, 0.012460, 0.010502, 0.011904, 0.011483, 0.010067, 0.013356, 0.020792, 0.027368, 0.026382, 0.028554, 0.028164, 0.029993, 0.033232, 0.028830, 0.022354, 0.027991, 0.029607, 0.020011, 0.031066, 0.031755, 0.025061, 0.037228, 0.024607, 0.041453
	-0.012463, -0.000987, -0.008994, -0.014815, -0.017487, -0.026372, -0.031392, -0.028459, -0.025402, -0.024153, -0.015566, -0.007862, -0.004579, 0.001484, 0.010757, 0.017401, 0.019536, 0.016264, 0.016278, 0.018231, 0.018193, 0.018217, 0.025442, 0.034794, 0.036179, 0.034770, 0.033985, 0.040104, 0.040404, 0.034161, 0.030977, 0.032380, 0.034144, 0.031909, 0.033231, 0.035957, 0.034171, 0.033050, 0.038776, 0.042972
	-0.002758, 0.000700, -0.008467, -0.011525, -0.018705, -0.027522, -0.031609, -0.027494, -0.026315, -0.023221, -0.014164, -0.006562, -0.002205, 0.006453, 0.013689, 0.018647, 0.017673, 0.016751, 0.017380, 0.018782, 0.019038, 0.021992, 0.027475, 0.034748, 0.036870, 0.036635, 0.035394, 0.037519, 0.038008, 0.032063, 0.025834, 0.030409, 0.033142, 0.023991, 0.034882, 0.034323, 0.030317, 0.042711, 0.030793, 0.045129
	-0.011501, 0.004979, -0.003199, -0.009532, -0.013737, -0.022490, -0.028056, -0.025047, -0.023987, -0.021727, -0.011113, -0.003633, 0.003070, 0.010580, 0.020230, 0.025058, 0.026653, 0.024592, 0.024567, 0.025613, 0.027386, 0.029282, 0.037705, 0.042901, 0.046601, 0.045443, 0.044217, 0.048155, 0.045715, 0.039788, 0.034981, 0.038594, 0.038594, 0.034532, 0.038671, 0.042065, 0.040659, 0.042101, 0.045919, 0.050030
	-0.005239, 0.006624, -0.001837, -0.005350, -0.012024, -0.022230, -0.026144, -0.022704, -0.021559, -0.017450, -0.008515, 0.000433, 0.007392, 0.014546, 0.023538, 0.029043, 0.029892, 0.027280, 0.028785, 0.030662, 0.032758, 0.032649, 0.040035, 0.046372, 0.048654, 0.050330, 0.049538, 0.049746, 0.048851, 0.041068, 0.034598, 0.041375, 0.041379, 0.030621, 0.043091, 0.044712, 0.038634, 0.053475, 0.042814, 0.059369
	-0.011843, 0.005417, 0.000007, -0.005709, -0.011391, -0.019100, -0.024151, -0.021274, -0.019356, -0.016953, -0.004422, 0.002891, 0.010688, 0.018353, 0.027665, 0.035281, 0.036655, 0.034937, 0.036795, 0.039994, 0.042705, 0.042668, 0.048600, 0.055673, 0.059602, 0.061002, 0.059934, 0.064283, 0.061835, 0.052838, 0.048644, 0.048401, 0.048158, 0.044262, 0.049173, 0.053313, 0.050054, 0.051718, 0.058112, 0.062677
	-0.003249, 0.007140, -0.000190, -0.005182, -0.010664, -0.017472, -0.021072, -0.018928, -0.015929, -0.011810, -0.001170, 0.006999, 0.014346, 0.022026, 0.033087, 0.037703, 0.039304, 0.038986, 0.040531, 0.042739, 0.044912, 0.045850, 0.052980, 0.060894, 0.062495, 0.065477, 0.066306, 0.069035, 0.066301, 0.058359, 0.048879, 0.054660, 0.053906, 0.042834, 0.051292, 0.054304, 0.049390, 0.064968, 0.053062, 0.067337
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 80.0
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Peperations]
version = 1
points = 
	0.022498, 0.020830, 0.014175, -0.000111, -0.007965, -0.011932, -0.009252, -0.003320, -0.000118, 0.004151, 0.015991, 0.024593, 0.030148, 0.034696, 0.042241, 0.043592, 0.045307, 0.051419, 0.057700, 0.066468, 0.072764, 0.085492, 0.100446, 0.113063, 0.118900, 0.122870, 0.130290, 0.129755, 0.129462, 0.124089, 0.122420, 0.123461, 0.116841, 0.117893, 0.119241, 0.115227, 0.110631, 0.109920, 0.117187, 0.124332
	0.004953, 0.000716, -0.005511, -0.010742, -0.018400, -0.024021, -0.019665, -0.013525, -0.009878, -0.004126, 0.008939, 0.016408, 0.019292, 0.023840, 0.033007, 0.033600, 0.034448, 0.041047, 0.049029, 0.052882, 0.062512, 0.072410, 0.089182, 0.103027, 0.106205, 0.110789, 0.117912, 0.115269, 0.112784, 0.106051, 0.103603, 0.104209, 0.099603, 0.105100, 0.101466, 0.099610, 0.095780, 0.096420, 0.108661, 0.108286
	-0.007933, -0.002801, -0.011350, -0.022484, -0.029473, -0.033231, -0.030354, -0.021826, -0.018408, -0.013209, 0.001640, 0.008984, 0.012027, 0.014149, 0.024334, 0.028649, 0.030597, 0.034667, 0.041223, 0.046241, 0.051968, 0.062511, 0.079099, 0.090699, 0.097837, 0.101667, 0.108218, 0.106595, 0.104490, 0.095444, 0.089512, 0.089259, 0.089179, 0.091741, 0.094161, 0.094254, 0.091002, 0.088753, 0.095405, 0.102343
	-0.010759, -0.012564, -0.018170, -0.023960, -0.033106, -0.040910, -0.038354, -0.031441, -0.026122, -0.019953, -0.006267, 0.000733, 0.002678, 0.006102, 0.015437, 0.019860, 0.022689, 0.029563, 0.035629, 0.037302, 0.045089, 0.055137, 0.070820, 0.082978, 0.087158, 0.088614, 0.094487, 0.093851, 0.091038, 0.080923, 0.074433, 0.073797, 0.073058, 0.081788, 0.080734, 0.083111, 0.078149, 0.079373, 0.091335, 0.087853
	-0.027313, -0.019238, -0.027920, -0.036645, -0.043223, -0.049872, -0.048503, -0.043853, -0.040737, -0.035179, -0.021622, -0.013493, -0.010171, -0.007317, 0.001347, 0.007440, 0.011360, 0.015985, 0.023916, 0.026329, 0.031680, 0.042865, 0.056754, 0.067621, 0.072919, 0.075964, 0.080156, 0.081233, 0.077771, 0.068443, 0.063939, 0.062251, 0.063828, 0.065094, 0.069498, 0.071735, 0.067423, 0.064065, 0.069162, 0.076272
	-0.033298, -0.035618, -0.039940, -0.043358, -0.050731, -0.061413, -0.060545, -0.055944, -0.052261, -0.045471, -0.035624, -0.027633, -0.021472, -0.017300, -0.006949, -0.002776, -0.000154, 0.006413, 0.012882, 0.014721, 0.023411, 0.031711, 0.040565, 0.054702, 0.058761, 0.061734, 0.065369, 0.066037, 0.061059, 0.053849, 0.049600, 0.048373, 0.049189, 0.054631, 0.050470, 0.056349, 0.047074, 0.049651, 0.057444, 0.057485
	-0.046284, -0.039039, -0.049010, -0.054961, -0.061001, -0.068408, -0.069602, -0.066474, -0.063117, -0.059357, -0.049570, -0.041166, -0.035441, -0.029269, -0.019658, -0.012395, -0.008906, -0.005538, 0.002012, 0.008339, 0.013216, 0.018793, 0.031185, 0.040165, 0.047175, 0.050605, 0.054283, 0.054442, 0.049166, 0.043483, 0.039000, 0.040758, 0.040857, 0.040759, 0.042263, 0.043438, 0.040051, 0.035886, 0.041332, 0.048851
	-0.049893, -0.051919, -0.058103, -0.060142, -0.067656, -0.077159, -0.079195, -0.078019, -0.075421, -0.069471, -0.060409, -0.054194, -0.044226, -0.037275, -0.027912, -0.020020, -0.016789, -0.012491, -0.003457, 0.001129, 0.004540, 0.009435, 0.018232, 0.027941, 0.035138, 0.038227, 0.042656, 0.044103, 0.038517, 0.032121, 0.029666, 0.027319, 0.029774, 0.031572, 0.028887, 0.034828, 0.023795, 0.030023, 0.033606, 0.036047
	-0.061015, -0.055279, -0.067497, -0.072234, -0.078637, -0.083600, -0.085954, -0.087271, -0.088647, -0.083447, -0.073398, -0.065920, -0.058009, -0.048810, -0.040714, -0.032533, -0.027328, -0.020402, -0.011382, -0.006547, -0.005452, -0.002712, 0.004649, 0.014201, 0.021442, 0.025510, 0.032890, 0.034711, 0.030965, 0.026329, 0.018828, 0.019246, 0.018861, 0.019611, 0.020596, 0.021396, 0.020172, 0.015723, 0.020537, 0.029677
	-0.063777, -0.066149, -0.073750, -0.076131, -0.084016, -0.091900, -0.093741, -0.094496, -0.094840, -0.089548, -0.084332, -0.077263, -0.068485, -0.061963, -0.051082, -0.043658, -0.037912, -0.032323, -0.024324, -0.019914, -0.018261, -0.013727, -0.003485, 0.004316, 0.011418, 0.017023, 0.022980, 0.024505, 0.018896, 0.014000, 0.009498, 0.006074, 0.009480, 0.007611, 0.008958, 0.010086, -0.000341, 0.010423, 0.010467, 0.016794
	-0.072341, -0.064233, -0.079217, -0.084483, -0.091050, -0.094481, -0.095378, -0.096667, -0.100564, -0.098313, -0.093254, -0.086700, -0.079209, -0.071795, -0.061313, -0.051911, -0.046317, -0.042643, -0.037228, -0.031598, -0.027431, -0.020480, -0.012883, -0.003114, 0.004746, 0.010189, 0.015911, 0.017106, 0.014037, 0.008693, 0.005120, 0.003652, -0.000532, -0.001097, 0.001984, 0.000397, -0.002089, -0.002821, 0.000529, 0.009043
	-0.068927, -0.075835, -0.083530, -0.085213, -0.091299, -0.100015, -0.101020, -0.100921, -0.103349, -0.102493, -0.098069, -0.091292, -0.083452, -0.079672, -0.069612, -0.062472, -0.055862, -0.052233, -0.046746, -0.041991, -0.035219, -0.028225, -0.018698, -0.007309, -0.002458, 0.002051, 0.006595, 0.008468, 0.005218, -0.000205, -0.003131, -0.003647, -0.006151, -0.009154, -0.005539, -0.006971, -0.015297, -0.002874, -0.005242, 0.003706
	-0.070116, -0.067835, -0.086390, -0.089881, -0.095167, -0.099194, -0.100751, -0.103794, -0.106996, -0.105835, -0.098564, -0.092154, -0.085579, -0.083053, -0.074722, -0.066442, -0.059302, -0.053429, -0.047800, -0.042952, -0.039132, -0.034614, -0.025732, -0.012689, -0.005906, 0.001101, 0.006644, 0.010980, 0.007742, 0.002526, -0.000261, -0.004094, -0.008771, -0.008465, -0.007095, -0.008952, -0.010405, -0.010446, -0.006121, 0.002024
	-0.064366, -0.071780, -0.082938, -0.085702, -0.093522, -0.099237, -0.104020, -0.105939, -0.106226, -0.104298, -0.097541, -0.091253, -0.084969, -0.082450, -0.075561, -0.066547, -0.056511, -0.051248, -0.041287, -0.037794, -0.035633, -0.028059, -0.019518, -0.010556, -0.003388, 0.002054, 0.009492, 0.011478, 0.008555, 0.004735, -0.000781, -0.006427, -0.005697, -0.010270, -0.006112, -0.011704, -0.018717, -0.002750, -0.010971, 0.000116
	-0.076795, -0.064801, -0.080209, -0.085175, -0.093457, -0.101077, -0.104981, -0.106367, -0.106821, -0.105708, -0.098545, -0.090759, -0.086929, -0.083491, -0.074306, -0.064805, -0.055933, -0.049959, -0.042853, -0.036270, -0.034463, -0.029587, -0.018780, -0.010103, -0.003533, 0.001632, 0.007909, 0.014370, 0.009281, 0.004666, -0.002974, -0.007301, -0.010185, -0.008299, -0.006340, -0.009678, -0.011333, -0.010684, -0.006289, 0.002763
	-0.067470, -0.065770, -0.074038, -0.076420, -0.085702, -0.098704, -0.101940, -0.102629, -0.101903, -0.100342, -0.093820, -0.086941, -0.083804, -0.081020, -0.067700, -0.059395, -0.054055, -0.047911, -0.039687, -0.035672, -0.032029, -0.025979, -0.017057, -0.006973, -0.001656, 0.002001, 0.007249, 0.012112, 0.006541, 0.000572, -0.006284, -0.010415, -0.012279, -0.015087, -0.007848, -0.016491, -0.019704, -0.005357, -0.013151, 0.002966
	-0.074820, -0.054794, -0.069710, -0.075127, -0.082743, -0.091434, -0.095621, -0.097541, -0.099098, -0.097422, -0.089851, -0.083594, -0.081112, -0.078942, -0.066391, -0.057457, -0.050942, -0.048077, -0.041211, -0.034391, -0.030091, -0.026047, -0.014207, -0.005090, 0.000912, 0.005316, 0.010043, 0.015509, 0.011199, 0.004513, -0.001027, -0.006694, -0.011239, -0.011162, -0.009134, -0.013596, -0.014031, -0.011306, -0.007627, 0.001767
	-0.061695, -0.056074, -0.065188, -0.067950, -0.076218, -0.088303, -0.093436, -0.092999, -0.090937, -0.090555, -0.084407, -0.080354, -0.078692, -0.074308, -0.062767, -0.052729, -0.047475, -0.043949, -0.036669, -0.031720, -0.027940, -0.020058, -0.010125, -0.000940, 0.003512, 0.007720, 0.011869, 0.015296, 0.011180, 0.003886, -0.003309, -0.003380, -0.007926, -0.011633, -0.003540, -0.014182, -0.013975, -0.003720, -0.011797, 0.006338
	-0.070864, -0.046187, -0.061128, -0.065717, -0.072715, -0.083470, -0.088292, -0.087558, -0.087628, -0.089378, -0.083768, -0.077237, -0.077063, -0.071978, -0.061635, -0.052022, -0.046913, -0.041194, -0.034314, -0.028661, -0.027048, -0.021438, -0.009769, -0.001205, 0.004637, 0.008928, 0.013264, 0.017277, 0.013442, 0.007295, 0.003623, -0.002524, -0.004256, -0.005789, -0.004213, -0.007305, -0.010487, -0.010885, -0.006086, 0.007386
	-0.059345, -0.049207, -0.056858, -0.060052, -0.066579, -0.080604, -0.086910, -0.085647, -0.085267, -0.087618, -0.081260, -0.075368, -0.073937, -0.069758, -0.058235, -0.051634, -0.045288, -0.038732, -0.032262, -0.027928, -0.024928, -0.019266, -0.007996, 0.000923, 0.005834, 0.008336, 0.013557, 0.017068, 0.012350, 0.006475, 0.000982, 0.001103, -0.006223, -0.006853, -0.000966, -0.013148, -0.013975, -0.006310, -0.011605, 0.006165
	-0.066591, -0.039715, -0.053663, -0.059514, -0.065911, -0.075018, -0.080214, -0.082968, -0.083447, -0.085380, -0.079055, -0.071985, -0.070247, -0.065856, -0.057767, -0.049975, -0.044481, -0.039103, -0.031217, -0.024927, -0.020997, -0.016440, -0.004831, 0.004061, 0.009463, 0.011160, 0.014777, 0.020638, 0.017816, 0.011360, 0.006171, 0.002164, -0.002119, -0.003117, -0.003031, -0.005156, -0.011400, -0.011762, -0.009295, -0.000001
	-0.060314, -0.046160, -0.052794, -0.054967, -0.062049, -0.074106, -0.080446, -0.081200, -0.080809, -0.080477, -0.076170, -0.070932, -0.069101, -0.063634, -0.055720, -0.049501, -0.044939, -0.040131, -0.032438, -0.022882, -0.017627, -0.012524, -0.001324, 0.006685, 0.011868, 0.013658, 0.016095, 0.021837, 0.020158, 0.012528, 0.006089, 0.005453, -0.000976, -0.002140, 0.001104, -0.010111, -0.010612, -0.007452, -0.014357, 0.001011
	-0.075633, -0.036609, -0.049346, -0.055490, -0.059336, -0.067616, -0.073859, -0.075613, -0.076372, -0.078009, -0.070627, -0.064206, -0.064430, -0.061999, -0.054551, -0.047386, -0.040817, -0.037398, -0.028062, -0.018505, -0.012195, -0.007531, 0.001481, 0.011790, 0.019955, 0.022349, 0.022131, 0.024492, 0.023359, 0.019186, 0.014655, 0.008357, 0.004176, 0.002971, 0.002955, -0.000237, -0.005884, -0.010152, -0.009506, 0.002811
	-0.059008, -0.039658, -0.046978, -0.048324, -0.052285, -0.063338, -0.069082, -0.070556, -0.070625, -0.070049, -0.064460, -0.057403, -0.056723, -0.052882, -0.046968, -0.041507, -0.033211, -0.029974, -0.022900, -0.013579, -0.008803, -0.004962, 0.005653, 0.017026, 0.028171, 0.028651, 0.024731, 0.026850, 0.023371, 0.017073, 0.015171, 0.016616, 0.005521, 0.005756, 0.007586, -0.005103, -0.006856, -0.005604, -0.006599, 0.007528
	-0.068330, -0.030233, -0.043154, -0.047439, -0.047149, -0.051149, -0.060971, -0.063014, -0.065775, -0.064636, -0.058200, -0.050987, -0.050925, -0.050115, -0.041299, -0.033907, -0.026306, -0.024199, -0.017123, -0.009196, -0.006314, -0.003809, 0.004760, 0.015324, 0.026665, 0.029649, 0.028724, 0.027131, 0.025150, 0.021808, 0.019981, 0.016766, 0.012347, 0.008776, 0.005760, -0.000224, -0.004294, -0.005879, -0.002457, 0.010054
	-0.053519, -0.031388, -0.038255, -0.037590, -0.039245, -0.046335, -0.056314, -0.057830, -0.060291, -0.058967, -0.051413, -0.045449, -0.043947, -0.042018, -0.034113, -0.025887, -0.019539, -0.017727, -0.012711, -0.005860, -0.003102, 0.000774, 0.009438, 0.015884, 0.022961, 0.024229, 0.026012, 0.029407, 0.026717, 0.020406, 0.017796, 0.020289, 0.012243, 0.009711, 0.009234, -0.005990, -0.001013, 0.000740, -0.002144, 0.013012
	-0.068972, -0.023416, -0.032912, -0.036134, -0.035915, -0.040435, -0.047452, -0.051460, -0.055021, -0.055776, -0.048697, -0.039554, -0.036785, -0.035561, -0.029056, -0.021075, -0.013416, -0.012134, -0.007237, -0.000622, 0.001662, 0.005393, 0.012038, 0.019764, 0.023514, 0.026252, 0.028191, 0.031400, 0.031365, 0.027993, 0.023275, 0.021009, 0.018930, 0.014093, 0.009022, 0.004773, 0.002094, 0.001348, 0.005643, 0.015078
	-0.050527, -0.022437, -0.028090, -0.026206, -0.028387, -0.036911, -0.041310, -0.044227, -0.046970, -0.046769, -0.038081, -0.031386, -0.029516, -0.024050, -0.019435, -0.012381, -0.005732, -0.004173, 0.000911, 0.006849, 0.007360, 0.010699, 0.017436, 0.023369, 0.028527, 0.029640, 0.031002, 0.034727, 0.036582, 0.030763, 0.026015, 0.028623, 0.020834, 0.016185, 0.016933, 0.002829, 0.004984, 0.009818, 0.008874, 0.020032
	-0.067395, -0.010220, -0.021024, -0.024567, -0.024087, -0.029620, -0.032317, -0.034341, -0.038392, -0.038789, -0.030285, -0.021590, -0.017175, -0.014435, -0.007732, -0.000529, 0.005605, 0.007078, 0.012454, 0.017758, 0.016774, 0.015574, 0.020748, 0.028369, 0.033644, 0.034771, 0.036537, 0.040293, 0.042118, 0.039979, 0.035655, 0.033354, 0.030928, 0.024890, 0.021491, 0.018938, 0.013668, 0.012501, 0.017108, 0.023515
	-0.038833, -0.012802, -0.018564, -0.017459, -0.019062, -0.027068, -0.030119, -0.028336, -0.029665, -0.030695, -0.022239, -0.013522, -0.008358, -0.004785, 0.000463, 0.010662, 0.015564, 0.016950, 0.020281, 0.025300, 0.022680, 0.022717, 0.026679, 0.031617, 0.035801, 0.037098, 0.041294, 0.045640, 0.047879, 0.042000, 0.038044, 0.040629, 0.033892, 0.031247, 0.031584, 0.018500, 0.020116, 0.019823, 0.016638, 0.029979
	-0.054356, -0.002258, -0.012712, -0.017288, -0.016713, -0.022907, -0.024293, -0.021563, -0.022620, -0.021953, -0.015330, -0.005386, -0.000764, 0.002640, 0.009997, 0.022869, 0.028174, 0.027730, 0.030977, 0.035707, 0.032818, 0.030889, 0.033638, 0.038561, 0.044265, 0.045141, 0.047683, 0.051815, 0.054004, 0.050991, 0.045574, 0.043899, 0.044055, 0.039092, 0.035909, 0.032091, 0.026891, 0.022169, 0.024865, 0.030848
	-0.031827, -0.000102, -0.006368, -0.006487, -0.006247, -0.014001, -0.017110, -0.013043, -0.010851, -0.008764, -0.000213, 0.006477, 0.011144, 0.018309, 0.024745, 0.033643, 0.038648, 0.039249, 0.041148, 0.045266, 0.041693, 0.040999, 0.045484, 0.052613, 0.057066, 0.054753, 0.055112, 0.059287, 0.060203, 0.052465, 0.047993, 0.050999, 0.047464, 0.046460, 0.044507, 0.031433, 0.032267, 0.032025, 0.029852, 0.040329
	-0.053848, 0.008122, -0.005187, -0.009032, -0.006543, -0.010012, -0.013005, -0.011663, -0.008957, -0.004668, 0.005458, 0.012800, 0.016893, 0.023554, 0.031737, 0.038741, 0.043870, 0.043337, 0.046621, 0.047581, 0.045654, 0.044827, 0.050363, 0.058747, 0.061023, 0.060485, 0.059059, 0.061821, 0.061391, 0.055971, 0.051067, 0.050038, 0.051018, 0.046533, 0.043334, 0.042562, 0.036118, 0.029798, 0.032773, 0.039524
	-0.025830, 0.006164, -0.000655, 0.000164, 0.000088, -0.008033, -0.011008, -0.006017, -0.001301, 0.004088, 0.011848, 0.020276, 0.024465, 0.033383, 0.039126, 0.044268, 0.047916, 0.047402, 0.050050, 0.050456, 0.048891, 0.051771, 0.058154, 0.063246, 0.065463, 0.063072, 0.060950, 0.065351, 0.064614, 0.057455, 0.051194, 0.055723, 0.050906, 0.046407, 0.048283, 0.036561, 0.037400, 0.036887, 0.031589, 0.046759
	-0.041184, 0.017683, 0.006408, 0.000358, 0.001923, -0.002498, -0.003907, -0.001746, 0.001864, 0.006784, 0.017297, 0.026916, 0.030940, 0.036439, 0.045987, 0.050809, 0.054636, 0.052055, 0.053180, 0.056698, 0.057069, 0.055779, 0.063193, 0.067815, 0.071856, 0.070651, 0.067674, 0.070718, 0.070797, 0.062598, 0.057842, 0.056835, 0.056713, 0.051260, 0.048727, 0.048227, 0.044844, 0.039559, 0.041218, 0.044920
	-0.014008, 0.018619, 0.011274, 0.010878, 0.008771, 0.001246, -0.001819, 0.003600, 0.008052, 0.011983, 0.021970, 0.030757, 0.037662, 0.045972, 0.053195, 0.057661, 0.059206, 0.058383, 0.060240, 0.061039, 0.062504, 0.064497, 0.070278, 0.077704, 0.080246, 0.077015, 0.072985, 0.075685, 0.072584, 0.063534, 0.057732, 0.061938, 0.057545, 0.050931, 0.054863, 0.045820, 0.048882, 0.049675, 0.043484, 0.051538
	-0.045038, 0.028947, 0.019821, 0.012917, 0.013648, 0.007951, 0.005122, 0.007823, 0.012411, 0.015320, 0.025036, 0.036734, 0.045314, 0.052208, 0.062220, 0.065610, 0.068489, 0.066665, 0.068454, 0.069025, 0.071080, 0.073373, 0.079623, 0.085651, 0.088907, 0.088954, 0.084254, 0.084464, 0.080300, 0.072471, 0.067316, 0.066430, 0.065143, 0.057630, 0.058650, 0.059627, 0.057197, 0.054105, 0.055295, 0.057879
	-0.017117, 0.027364, 0.023067, 0.022758, 0.019246, 0.011825, 0.007962, 0.011522, 0.017237, 0.021779, 0.031329, 0.042642, 0.052349, 0.060322, 0.069568, 0.074657, 0.075211, 0.072882, 0.075373, 0.078391, 0.079512, 0.081816, 0.086101, 0.091730, 0.095061, 0.095682, 0.092100, 0.092873, 0.085769, 0.077219, 0.068392, 0.073179, 0.069972, 0.061240, 0.068306, 0.062227, 0.061008, 0.064520, 0.058543, 0.070728
	-0.042759, 0.035472, 0.029514, 0.023812, 0.024176, 0.020576, 0.017397, 0.018716, 0.022981, 0.027634, 0.041262, 0.050991, 0.058558, 0.067060, 0.077829, 0.083609, 0.084719, 0.082815, 0.085352, 0.087363, 0.091238, 0.091692, 0.096562, 0.102513, 0.106436, 0.108184, 0.105828, 0.107257, 0.102415, 0.090768, 0.084257, 0.081410, 0.081286, 0.073523, 0.074433, 0.076576, 0.070376, 0.068350, 0.071896, 0.072962
	-0.003143, 0.035517, 0.033266, 0.032727, 0.031843, 0.025862, 0.023177, 0.026936, 0.032953, 0.037457, 0.049289, 0.057429, 0.066625, 0.072540, 0.083814, 0.089321, 0.092420, 0.093053, 0.094752, 0.096876, 0.098364, 0.101271, 0.105185, 0.113505, 0.115784, 0.118957, 0.117138, 0.117934, 0.110930, 0.101497, 0.091051, 0.092731, 0.090574, 0.079282, 0.084691, 0.078426, 0.073451, 0.081698, 0.072811, 0.084352
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 19.8
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 130, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 123, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 112, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 1766, in load_config
    return BedMesh(config)
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 107, in __init__
    self.splitter = MoveSplitter(config, self.gcode)
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 1259, in __init__
    self.split_delta_z = config.getfloat(
  File "/home/pi/klipper/klippy/configfile.py", line 70, in getfloat
    return self._get_wrapper(self.fileconfig.getfloat, option, default,
  File "/home/pi/klipper/klippy/configfile.py", line 49, in _get_wrapper
    raise error("Option '%s' in section '%s' must have minimum of %s"
configparser.Error: Option 'split_delta_z' in section 'bed_mesh' must have minimum of 0.01
webhooks client 4128676232: New connection
webhooks client 4128676232: Client info {'program': 'Moonraker', 'version': 'v0.9.3-0-g71f9e67'}
webhooks client 4128676232: Disconnected
Restarting printer
Start printer at Tue Mar 17 03:56:35 2026 (1773719795.8 9400.2)
===== Config file =====
[mcu rpi]
serial = /tmp/klipper_host_mcu

[board_pins btt-octopus-pro-h723-11]
aliases = 
	
	
	
	x_step_pin=PF13,
	x_dir_pin=PF12,
	x_enable_pin=PF14,
	x_uart_pin=PC4,
	x_diag_pin=PG6,
	x_endstop_pin=PG6,
	
	
	
	dual_carriage_step_pin=PF9,
	dual_carriage_dir_pin=PF10,
	dual_carriage_enable_pin=PG2,
	dual_carriage_uart_pin=PF2,
	dual_carriage_diag_pin=PG12,
	dual_carriage_endstop_pin=PG12,
	
	
	
	y_step_pin=PG0,
	y_dir_pin=PG1,
	y_enable_pin=PF15,
	y_uart_pin=PD11,
	y_diag_pin=PG9,
	y_endstop_pin=PG9,
	
	
	
	y1_step_pin=PG4,
	y1_dir_pin=PC1,
	y1_enable_pin=PA2,
	y1_uart_pin=PC7,
	y1_diag_pin=PG11,
	y1_endstop_pin=PG11,
	
	
	
	z0_step_pin=PC13,
	z0_dir_pin=PF0,
	z0_enable_pin=PF1,
	z0_uart_pin=PE4,
	z0_diag_pin=PG13,
	
	
	
	z1_step_pin=PE2,
	z1_dir_pin=PE3,
	z1_enable_pin=PD4,
	z1_uart_pin=PE1,
	z1_diag_pin=PG14,
	
	
	
	z2_step_pin=PE6,
	z2_dir_pin=PA14,
	z2_enable_pin=PE0,
	z2_uart_pin=PD3,
	z2_diag_pin=PG15,
	
	e_step_pin=PF11,
	e_dir_pin=PG3,
	e_enable_pin=PG5,
	e_uart_pin=PC6,
	
	e_heater_pin=PA2,
	e_sensor_pin=PF4,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=PA7,
	stepper_spi_miso_pin=PA6,
	stepper_spi_sclk_pin=PA5,
	adxl345_cs_pin=PA15,
	bltouch_sensor_pin=PB7,
	bltouch_control_pin=PB6,
	probe_pin=PB7,
	fan_part_cooling_pin=PA8,
	fan_toolhead_cooling_pin=PE5,
	fan_controller_board_pin=PD12,
	heater_bed_heating_pin=PA1,
	heater_bed_sensor_pin=PF3,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PG15,
	filament_sensor_motion_pin=PG14,
	ratrig_vaoc_probe_pin=PG10,
	ratrig_vaoc_led_pin=PB0,
	ratrig_vaoc_fan_pin=PD13,
	chamber_lighting_pin=PB11,
	chamber_filter_4p_fan_pin=PD14,
	chamber_filter_4p_fan_enable_pin=PD15

[mcu]
serial = /dev/RatOS/btt-octopus-pro-h723-11

[temperature_sensor Octopus_Pro_H723_V1.1]
sensor_type = temperature_mcu

[adxl345 controlboard]
cs_pin = PA15
spi_software_mosi_pin = PB5
spi_software_miso_pin = PB4
spi_software_sclk_pin = PB3

[board_pins toolboard_t0]
mcu = toolboard_t0
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t0]
serial = /dev/RatOS/btt-ebb42-gen2-10-t0

[temperature_sensor EBB42_Gen2_v1.0_T0]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t0

[lis2dw toolboard_t0]
axes_map = x, z, y
cs_pin = toolboard_t0:PB1
spi_software_mosi_pin = toolboard_t0:PB11
spi_software_miso_pin = toolboard_t0:PB2
spi_software_sclk_pin = toolboard_t0:PB10

[board_pins toolboard_t1]
mcu = toolboard_t1
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t1]
serial = /dev/RatOS/btt-ebb42-gen2-10-t1

[temperature_sensor EBB42_Gen2_v1.0_T1]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t1

[lis2dw toolboard_t1]
axes_map = x, z, y
cs_pin = toolboard_t1:PB1
spi_software_mosi_pin = toolboard_t1:PB11
spi_software_miso_pin = toolboard_t1:PB2
spi_software_sclk_pin = toolboard_t1:PB10

[gcode_macro RatOS]
variable_homing = "endstops"
variable_z_probe = "static"
variable_sensorless_x_current = 0.6
variable_sensorless_y_current = 0.9
variable_safe_home_x = "middle"
variable_safe_home_y = "middle"
variable_driver_type_x = "tmc2209"
variable_driver_type_y = "tmc2209"
variable_stowable_probe_stop_on_error = False
variable_chamber_filter_enable = True
variable_chamber_filter_speed = 0.5
variable_chamber_filter_disable_speed = 1.0
variable_chamber_filter_enable_at = "after_print_start"
variable_chamber_filter_disable_period = 300
variable_chamber_filter_disable_bed_temp = 0
variable_chamber_heater_enable = True
variable_chamber_heater_bed_temp = 115
variable_chamber_heater_preheating_temp = 150
variable_chamber_heater_heating_temp_offset = 25
variable_chamber_heater_control_external_heater = False
variable_chamber_heater_air_circulation_enable = True
variable_chamber_heater_air_circulation_fan_speed = 0.35
variable_chamber_heater_air_circulation_y_pos = 0
variable_chamber_heater_air_circulation_z_pos = 100
variable_chamber_heater_extra_fan_speed = 1.0
variable_chamber_heater_filter_fan_speed = 1.0
variable_bed_heat_soak_time = 0
variable_hotend_heat_soak_time = 0
variable_led_status_action = 0.0,1.0,1.0
variable_led_status_success = 0.0,1.0,0.0
variable_led_status_error = 1.0,0.0,1.0
variable_led_status_on = 1.0,1.0,1.0
variable_led_status_off = 0.0,0.0,1.0
variable_led_status_standby = 0.1,0.1,0.1
variable_led_status_heating = 1.0,0.0,0.0
variable_led_status_cooling = 0.0,0.0,1.0
variable_calibrate_bed_mesh = True
variable_adaptive_mesh = True
variable_start_print_park_in = "center"
variable_start_print_park_z_height = 3
variable_end_print_park_in = "back"
variable_pause_print_park_in = "back"
variable_end_print_park_z_hop = 20
variable_nozzle_priming = "primeblob"
variable_nozzle_prime_start_x = "max"
variable_nozzle_prime_start_y = "min"
variable_nozzle_prime_direction = "auto"
variable_nozzle_prime_bridge_fan = 102
variable_probe_for_priming_result = None
variable_probe_for_priming_end_result = None
variable_probe_for_priming_result_t1 = None
variable_probe_for_priming_end_result_t1 = None
variable_probe_for_priming_disable_mesh_constraints = False
variable_adaptive_prime_offset_threshold = -1.0
variable_last_z_offset = None
variable_runout_park_in = "front"
variable_enable_unload_tip_forming = False
variable_filament_unload_length = 150
description = RatOS variable storage macro, will echo variables to the console when run.
variable_relative_extrusion = True
variable_force_absolute_position = False
variable_preheat_extruder = True
variable_preheat_extruder_temp = 150
variable_macro_travel_speed = 600
variable_macro_travel_accel = 8000
variable_macro_z_speed = 15
variable_bed_margin_x = [59.6, 59.6]
variable_bed_margin_y = [14.35, 33.65]
variable_printable_x_min = 0
variable_printable_x_max = 0
variable_printable_y_min = 0
variable_printable_y_max = 0
variable_end_print_motors_off = True
variable_status_color_ok = "00FF00"
variable_status_color_error = "FF0000"
variable_status_color_unknown = "FFFF00"
variable_end_print_retract_filament = 10
gcode = 
	ECHO_RATOS_VARS
variable_auto_center_subject = False
variable_toolchange_zhop = 2.0
variable_toolchange_zspeed = 25
variable_toolchange_sync_fans = False
variable_toolchange_combined_zhop = False
variable_toolchange_travel_speed = 600
variable_toolchange_travel_accel = 8000
variable_toolchange_extrusion = 2.0
variable_toolchange_retraction = 2.0
variable_toolchange_feedrate = 7200
variable_toolchange_prepurging_timer = 0
variable_toolchange_standby_temp = -1
variable_toolchange_purge = 25
variable_toolchange_first_purge = 50
variable_beacon_bed_mesh_scv = 25
variable_beacon_contact_z_homing = False
variable_beacon_contact_start_print_true_zero = True
variable_beacon_contact_start_print_true_zero_fuzzy_position = True
variable_beacon_contact_calibrate_model_on_true_zero = True
variable_beacon_contact_wipe_before_true_zero = True
variable_beacon_contact_wipe_before_true_zero_method = "probe_clean"
variable_beacon_contact_true_zero_temp = 170
variable_beacon_contact_prime_probing = True
variable_beacon_contact_expansion_compensation = True
variable_beacon_contact_bed_mesh = False
variable_beacon_contact_bed_mesh_samples = 2
variable_beacon_contact_z_tilt_adjust = False
variable_beacon_contact_z_tilt_adjust_samples = 2
variable_beacon_scan_compensation_enable = True
variable_beacon_scan_compensation_profile = "auto"
variable_beacon_scan_compensation_desired_spacing = 10
variable_beacon_scan_compensation_bed_temp_mismatch_is_error = False
variable_beacon_contact_poke_bottom_limit = -1
variable_beacon_scan_method_automatic = False
variable_beacon_adaptive_heat_soak = True
variable_beacon_adaptive_heat_soak_max_wait = 5400
variable_beacon_adaptive_heat_soak_extra_wait_after_completion = 0
variable_beacon_adaptive_heat_soak_layer_quality = 3
variable_beacon_adaptive_heat_soak_maximum_first_layer_duration = 1800
variable_beacon_contact_start_print_true_zero_fuzzy_radius = 20
variable_homing_x = "endstop"
variable_homing_y = "endstop"
variable_default_toolhead = 0
variable_adxl_chip = ["lis2dw toolboard_t0", "lis2dw toolboard_t1"]
variable_shaper_x_freq = [54.2, 53.2, 53.6, 54.4]
variable_shaper_y_freq = [40.8, 47.6, 38.6, 38]
variable_shaper_x_type = ["mzv", "mzv", "mzv", "mzv"]
variable_shaper_y_type = ["mzv", "mzv", "mzv", "mzv"]
variable_x_driver_types = ["tmc5160"]
variable_x_axes = ["x"]
variable_y_driver_types = ["tmc5160", "tmc5160"]
variable_y_axes = ["y", "y1"]
variable_z_driver_types = ["tmc2209", "tmc2209", "tmc2209"]
variable_z_axes = ["z", "z1", "z2"]
variable_home_y_first = True

[ratos_homing]
axes = xyz
z_hop = 15
z_hop_speed = 15
gcode = 
	
	_LED_ON
	
	
	{% set prev_stop_on_error = printer["gcode_macro RatOS"].stowable_probe_stop_on_error %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set target_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	_IDEX_SINGLE
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE=True
	
	
	M400
	
	G90
	
	
	{% set X = true if params.X is defined else false %}
	{% set Y = true if params.Y is defined else false %}
	{% set Z = true if params.Z is defined else false %}
	{% if printer["gcode_macro RatOS"].home_y_first|default(false)|lower == 'true' %}
	HOME_Y X={X} Y={Y} Z={Z}
	HOME_X X={X} Y={Y} Z={Z}
	{% else %}
	HOME_X X={X} Y={Y} Z={Z}
	HOME_Y X={X} Y={Y} Z={Z}
	{% endif %}
	HOME_Z X={X} Y={Y} Z={Z}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE={prev_stop_on_error}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[gcode_macro HOME_X]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_x = printer["gcode_macro RatOS"].homing_x|lower %}
	{% set homing_x = homing_x if homing_x else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_X" MSG="printable_x_max: {printable_x_max}, safe_home_x: {safe_home_x}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}"
	
	
	{% if X or not Y and not Z %}
	{% if homing_x == 'endstop' %}
	G28 X
	{% elif homing_x == 'sensorless' %}
	{% if printer["dual_carriage"] is defined %}
	{ action_emergency_stop("sensorless homing not supported on IDEX!") }
	{% endif %}
	HOME_X_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_x to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_x, homing)) }
	{% endif %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1} MODE=PRIMARY
	G1 X{parking_position} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	{% endif %}
	{% set x_homed = True %}
	G0 X{safe_home_x} F{speed}
	M400
	{% endif %}

[gcode_macro HOME_Y]
gcode = 
	
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_y = printer["gcode_macro RatOS"].homing_y|lower %}
	{% set homing_y = homing_y if homing_y else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Y" MSG="printable_y_max: {printable_y_max}, safe_home_y: {safe_home_y}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}"
	
	
	{% if Y or not X and not Z %}
	{% if homing_y == 'endstop' %}
	G28 Y
	{% elif homing_y == 'sensorless' %}
	HOME_Y_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_y to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_y, homing)) }
	{% endif %}
	{% set y_homed = True %}
	G0 Y{safe_home_y} F{speed}
	{% endif %}

[gcode_macro HOME_Z]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	
	
	{% set beacon_contact_z_homing = true if printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_z_home_position_fuzzing_radius = printer["gcode_macro RatOS"].beacon_z_home_position_fuzzing_radius|default(0)|float %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Z" MSG="x_homed: {x_homed}, y_homed: {y_homed}, z_probe: {z_probe}, beacon_contact_z_homing: {beacon_contact_z_homing}"
	
	
	{% if Z or not Y and not X %}
	RATOS_ECHO MSG="Homing Z"
	{% if x_homed == False or y_homed == False %}
	{ action_emergency_stop("X and Y must be homed before homing Z") }
	{% else %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_homing %}
	{% if beacon_contact_start_print_true_zero %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% else %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	{% else %}
	G28 Z
	{% endif %}
	_Z_HOP
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro HOME_X_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	
	G4 P300
	
	G28 X
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"

[gcode_macro HOME_Y_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	
	G4 P300
	
	G28 Y
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"

[gcode_macro _Z_HOP]
description = Move Z axis up by Z_HOP distance at Z_HOP_SPEED. In relative mode it will move Z axis up by Z_HOP distance. In absolute mode it will move Z axis to Z_HOP distance.
gcode = 
	{% set z_hop = printer.fastconfig.config.ratos_homing.z_hop|float %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	G0 Z{z_hop} F{z_hop_speed}

[gcode_macro __MOVE_TO_SAFE_Z_HOME_ECHO_DEBUG]
gcode = 
	DEBUG_ECHO PREFIX="_MOVE_TO_SAFE_Z_HOME" MSG="x: {params.X}, y: {params.Y}, z_hop: {params.Z_HOP}, fuzzy_radius: {params.FUZZY_RADIUS}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}, printable_x_max: {printer['gcode_macro RatOS'].printable_x_max}, printable_y_max: {printer['gcode_macro RatOS'].printable_y_max}"

[gcode_macro MAYBE_HOME]
description = Only home unhomed axis. Specify ABL=1 to also ensure that automatic bed levelling is applied (if configured).
variable_is_kinematic_position_overriden = False
gcode = 
	{% set abl = params.ABL|default('')|lower in ('true', 'yes', '1') %}
	{% if printer["gcode_macro MAYBE_HOME"].is_kinematic_position_overriden|lower == 'true' %}
	RATOS_ECHO MSG="SET_CENTER_KINEMATIC_POSITION has been abused. Homing all axes. Please refrain from using SET_CENTER_KINEMATIC_POSITION outside of debugging purposes."
	G28
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=False
	{% else %}
	{% set axes = '' %}
	{% set isHomed = true %}
	{% set axesToHome = '' %}
	{% if params.X is defined %}
	{% set axes = axes ~ 'X ' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% endif %}
	{% if params.Y is defined %}
	{% set axes = axes ~ 'Y ' %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% endif %}
	{% if params.Z is defined %}
	{% set axes = axes ~ 'Z ' %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if params.X is not defined and params.Y is not defined and params.Z is not defined %}
	{% set axes = '' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if isHomed is false %}
	RATOS_ECHO MSG="Homing {axesToHome}"
	G28 {axesToHome}
	{% else %}
	RATOS_ECHO MSG="All requested axes already homed. Skipping homing."
	{% endif %}
	{% endif %}
	{% if abl %}
	{% if printer.z_tilt is defined %}
	{% if not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Performing Z tilt adjustment..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Z tilt already applied. Skipping Z tilt adjustment."
	{% endif %}
	{% elif printer.quad_gantry_level is defined %}
	{% if not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Performing quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Quad gantry leveling already applied. Skipping quad gantry leveling."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="No automatic bed leveling method configured. Skipping bed leveling."
	{% endif %}
	{% endif %}

[gcode_macro PID_CALIBRATE_HOTEND]
description = Perform a PID calibration test for a given extruder heater.
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set temp = params.TEMP|default(220)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_HOTEND" MSG="TEMP={temp}"
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO MSG="PID calibration hotend heater T0 at {temp}°C..."
	PID_CALIBRATE HEATER=extruder TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	
	{% if toolhead==0 or toolhead==1 %}
	RATOS_ECHO MSG="PID calibration hotend heater T{toolhead} at {temp}°C..."
	PID_CALIBRATE HEATER=extruder{'' if toolhead==0 else toolhead} TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_BED]
description = Perform a PID calibration test for the bed heater.
gcode = 
	
	{% set temp = params.TEMP|default(80)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_BED" MSG="TEMP={temp}"
	RATOS_ECHO MSG="PID calibration bed heater at {temp}°C..."
	
	
	PID_CALIBRATE HEATER=heater_bed TARGET={temp}
	
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_CHAMBER_HEATER]
description = Perform a PID calibration test for the chamber heater.
gcode = 
	
	{% set temp = params.TEMP|default(150)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_CHAMBER_HEATER" MSG="TEMP={temp}"
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	RATOS_ECHO MSG="PID calibration chamber heater at {temp}°C..."
	PID_CALIBRATE HEATER=chamber_heater TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_heater" %}
	{% set link_text = "RatOS Chamber Heater" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber heater found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro INITIALIZE_PA_TUNING]
description = Start a pressure advance tuning tower.
gcode = 
	
	{% set start = params.START|default(0.0)|float %}
	{% set factor = params.FACTOR|default(0.001)|float %}
	
	
	{% set layer_number = printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|default(0)|int %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if is_printing_gcode and layer_number < 2 %}
	DEBUG_ECHO PREFIX="START_PA_TOWER" MSG="START: {start}, FACTOR: {factor}"
	RATOS_ECHO MSG="Starting pressure advance tuning tower..."
	TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START={start} FACTOR={factor}
	{% else %}
	RATOS_ECHO MSG="Pressure advance tuning tower requires you to be printing gcode and on layer 1 to start."
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro CHAMBER_FILTER_ON]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	_CHAMBER_FILTER_TURN_ON
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro CHAMBER_FILTER_OFF]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Deactivating chamber filter..."
	_CHAMBER_FILTER_TURN_OFF
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set chamber_filter_enable_at = printer["gcode_macro RatOS"].chamber_filter_enable_at|default('after_print_start')|lower %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_ON" MSG="at: {at}, chamber_filter_enable: {chamber_filter_enable}, chamber_filter_enable_at: {chamber_filter_enable_at}, chamber_filter_speed: {chamber_filter_speed}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	{% if chamber_filter_enable_at == at %}
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	
	
	_CHAMBER_FILTER_TURN_ON AT={at}
	
	
	{% if chamber_filter_enable_at == "print_end" %}
	_LED_CHAMBER_FILTER_ON
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_OFF]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF" MSG="chamber_filter_enable: {chamber_filter_enable}, filter_disable_period: {filter_disable_period}, filter_disable_bed_temp: {filter_disable_bed_temp}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	
	{% if filter_disable_period > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting {filter_disable_period} seconds before turning chamber filter off..."
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION={filter_disable_period}
	{% endif %}
	
	
	{% if filter_disable_bed_temp > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting for bed temp to cool down to {filter_disable_bed_temp}°C to turn filter off..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM=0 MAXIMUM={filter_disable_bed_temp}
	_CHAMBER_FILTER_TURN_OFF
	_LED_CHAMBER_FILTER_OFF
	{% endif %}
	
	{% endif %}

[delayed_gcode _CHAMBER_FILTER_OFF_TIMER]
gcode = 
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF_TIMER" MSG="executed"
	
	
	_CHAMBER_FILTER_TURN_OFF
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Chamber filter turned off!"
	
	
	_LED_CHAMBER_FILTER_OFF

[gcode_macro _CHAMBER_FILTER_TURN_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_speed|default(0)|float %}
	{% if at == "print_end" %}
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_disable_speed|default(0)|float %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION=0
	
	
	SET_FAN_SPEED FAN=filter SPEED={chamber_filter_speed}

[gcode_macro _CHAMBER_FILTER_TURN_OFF]
gcode = 
	
	SET_FAN_SPEED FAN=filter SPEED=0

[gcode_macro _CHAMBER_FILTER_SANITY_CHECK]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	{% if filter_disable_bed_temp > 0 and filter_disable_period > 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable, not both.")}
	{% endif %}
	
	{% if filter_disable_bed_temp == 0 and filter_disable_period == 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable.")}
	{% endif %}
	
	{% endif %}

[gcode_macro CHAMBER_HEATER_ON]
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(45)|int %}
	
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp} IS_FROM_START_PRINT=False

[gcode_macro CHAMBER_HEATER_OFF]
gcode = 
	_CHAMBER_HEATER_OFF

[gcode_macro _CHAMBER_HEATER_ON]
variable_chamber_temp = 0
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	{% set is_from_start_print = true if params.IS_FROM_START_PRINT|default(True)|lower == 'true' else false %}
	
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set chamber_heater_enable = true if printer["gcode_macro RatOS"].chamber_heater_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}
	{% set chamber_heater_preheating_temp = printer["gcode_macro RatOS"].chamber_heater_preheating_temp|default(150)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	{% set chamber_heater_control_external_heater = true if printer["gcode_macro RatOS"].chamber_heater_control_external_heater|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_enable = true if printer["gcode_macro RatOS"].chamber_heater_air_circulation_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_fan_speed = printer["gcode_macro RatOS"].chamber_heater_air_circulation_fan_speed|default(0.35)|float %}
	{% set chamber_heater_air_circulation_y_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_y_pos|default(0)|float %}
	{% set chamber_heater_air_circulation_z_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_z_pos|default(100)|float %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_HEATER_ON" MSG="chamber_heater_enable: {chamber_heater_enable}, chamber_heater_preheating_temp: {chamber_heater_preheating_temp}, chamber_heater_heating_temp_offset: {chamber_heater_heating_temp_offset}, bed_temp: {bed_temp}, chamber_temp: {chamber_temp}, start_chamber_temp: {start_chamber_temp}"
	
	
	{% if chamber_heater_enable and chamber_temp > 0 and chamber_heater_bed_temp > 0 %}
	
	
	_LED_HEATING
	
	
	RATOS_ECHO MSG="Preheating chamber to {(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}°C..."
	
	
	{% set chamber_temp_sensor = "extruder" %}
	{% if printer["dual_carriage"] is defined and default_toolhead == 1 %}
	{% set chamber_temp_sensor = "extruder1" %}
	{% endif %}
	{% if printer["temperature_sensor chamber"] is defined %}
	{% set chamber_temp_sensor = "temperature_sensor chamber" %}
	{% endif %}
	
	
	{% set current_chamber_temp = printer['%s' % chamber_temp_sensor].temperature|int %}
	
	
	{% set needs_heating = current_chamber_temp < (start_chamber_temp if start_chamber_temp > 0 else chamber_temp) %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_BEFORE_PREHEATING
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	{% if not is_from_start_print %}
	MAYBE_HOME
	{% endif %}
	G0 Z{chamber_heater_air_circulation_z_pos} F{z_speed}
	G0 Y{chamber_heater_air_circulation_y_pos} F{speed}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * chamber_heater_air_circulation_fan_speed)}
	{% endif %}
	{% else %}
	{% if is_from_start_print %}
	G0 Z{z} F{z_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE={chamber_temp}
	
	
	{% if needs_heating %}
	
	
	M140 S{chamber_heater_bed_temp}
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={chamber_heater_preheating_temp}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	
	{% endif %}
	
	
	{% if needs_heating %}
	_CHAMBER_HEATER_EXTRA_FAN_ON
	{% endif %}
	
	
	{% if needs_heating %}
	TEMPERATURE_WAIT SENSOR="{chamber_temp_sensor}" MINIMUM={(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% endif %}
	
	
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED=0
	_CHAMBER_FILTER_ON AT="before_print_start"
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	G28 Z
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_AFTER_PREHEATING
	{% endif %}
	
	
	{% if printer["temperature_sensor chamber"] is defined %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined and chamber_heater_control_external_heater %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	
	
	_LED_SUCCESS
	
	{% endif %}

[gcode_macro _CHAMBER_HEATER_OFF]
gcode = 
	RATOS_ECHO MSG="Deactivating chamber heater..."
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=0
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE=0
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	
	
	_CHAMBER_HEATER_EXTRA_FAN_OFF

[delayed_gcode _CHAMBER_HEATER_CONTROL]
initial_duration = 0.
gcode = 
	
	{% set chamber_temp = printer["gcode_macro _CHAMBER_HEATER_ON"].chamber_temp|default(0)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	
	
	{% set current_chamber_temp = printer['temperature_sensor chamber'].temperature|int %}
	
	
	{% if current_chamber_temp < chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	{% endif %}
	
	
	{% if current_chamber_temp >= chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_ON]
gcode = 
	
	{% set chamber_heater_extra_fan_speed = printer["gcode_macro RatOS"].chamber_heater_extra_fan_speed|default(0.0)|float %}
	
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	{% if chamber_heater_extra_fan_speed > 0 %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED={chamber_heater_extra_fan_speed}
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_OFF]
gcode = 
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED=0
	{% endif %}

[gcode_macro _USER_CHAMBER_HEATER_BEFORE_PREHEATING]
description = Will be executed before chamber preheating, only if heating is needed.
gcode = 

[gcode_macro _USER_CHAMBER_HEATER_AFTER_PREHEATING]
description = Will be executed after chamber preheating, only if heating was needed.
gcode = 

[gcode_macro RESET_HEATSOAK_SETTINGS]
description = Resets all heatsoak-related settings to startup defaults
gcode = 
	HEATSOAK_SETTINGS ACTION=reset

[gcode_macro USE_ADAPTIVE_HEATSOAK]
description = Temporarily enables adaptive bed heatsoaking (if a beacon probe is present), will reset to printer.cfg settings
	when Klipper is restarted. Optionally specify QUALITY (1-5) and maximum FIRST_LAYER_DURATION (in minutes).
	Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.QUALITY|default("1..5") %}
	{% set _ = params.FIRST_LAYER_DURATION|default("1..120 minutes") %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("Adaptive heatsoaking is only available when a beacon probe is configured.") }
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_quality = (settings.variable_beacon_adaptive_heat_soak_layer_quality if defsrc == 'startup' else current.beacon_adaptive_heat_soak_layer_quality)|default(3)|int %}
	{% set default_first_layer_duration_secs = (settings.variable_beacon_adaptive_heat_soak_maximum_first_layer_duration if defsrc == 'startup' else current.beacon_adaptive_heat_soak_maximum_first_layer_duration)|default(1800)|int %}
	{% if params2.QUALITY is defined %}
	{% set quality = params2.QUALITY|int %}
	{% if quality < 1 or quality > 5 %}
	{ action_raise_error("QUALITY must be between 1 (rough) and 5 (maximum). Use 3 (normal) if unsure.") }
	{% endif %}
	{% else %}
	{% set quality = default_quality %}
	{% endif %}
	{% if params2.FIRST_LAYER_DURATION is defined %}
	{% set first_layer_duration_mins = params2.FIRST_LAYER_DURATION|float %}
	{% if first_layer_duration_mins <= 0 %}
	{ action_raise_error("FIRST_LAYER_DURATION must be a positive number specifying the maximum first layer duration in minutes.") }
	{% endif %}
	{% if first_layer_duration_mins > 120 %}
	CONSOLE_ECHO MSG="FIRST_LAYER_DURATION will be limited to 120 minutes. Values larger than this will not have an effect on soak time."
	{% set first_layer_duration_mins = 120 %}
	{% endif %}
	{% set first_layer_duration_secs = (first_layer_duration_mins * 60.0)|int %}
	{% else %}
	{% set first_layer_duration_secs = default_first_layer_duration_secs %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	{% endif %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=True beacon_adaptive_heat_soak_layer_quality={quality} beacon_adaptive_heat_soak_maximum_first_layer_duration={first_layer_duration_secs}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."

[gcode_macro USE_FIXED_HEATSOAK]
description = Temporarily enables fixed bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
	Optionally specify DURATION (in minutes). Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.DURATION|default("0..720 minutes") %}
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_duration = (settings.variable_bed_heat_soak_time if defsrc == 'startup' else current.bed_heat_soak_time)|default(0)|int %}
	{% if params2.DURATION is defined %}
	{% set duration_mins = params2.DURATION|float %}
	{% if duration_mins < 0 %}
	{ action_raise_error("DURATION must be a non-negative number specifying the heatsoak duration in minutes.") }
	{% endif %}
	{% if duration_mins > 720 %}
	CONSOLE_ECHO MSG="DURATION will be limited to 720 minutes (12 hours). If you really need a larger value, adjust printer.cfg instead."
	{% set duration_mins = 720 %}
	{% endif %}
	{% set duration_secs = (duration_mins * 60.0)|int %}
	{% else %}
	{% set duration_secs = default_duration %}
	{% set duration_mins = duration_secs / 60.0 %}
	{% endif %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% if has_beacon %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=False bed_heat_soak_time={duration_secs}
	{% else %}
	HEATSOAK_SETTINGS QUIET=1 bed_heat_soak_time={duration_secs}
	{% endif %}
	{% if duration_mins < 1e-3 %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% else %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% endif %}

[gcode_macro USE_NO_HEATSOAK]
description = Temporarily disables bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
gcode = 
	USE_FIXED_HEATSOAK DURATION=0

[gcode_macro HEATSOAK_SETTINGS]
description = Shows or adjusts heatsoak settings
	- With no arguments: shows current heatsoak settings, specify VERBOSE=1 for detailed output
	- With arguments: sets the specified settings. Use the full setting name without the variable_ prefix, e.g. bed_heat_soak_time=300 or beacon_adaptive_heat_soak_layer_quality=4. See printer.cfg for available settings.
variable_default_source = "startup"
gcode = 
	
	{% set params2 = params %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% set quiet = params2.pop("QUIET", None)|default("0") in ("1", "true", "yes") %}
	{% set verbose = params2.pop("VERBOSE", None)|default("0") in ("1", "true", "yes") %}
	{% if has_beacon %}
	{% set vars = (
	"beacon_adaptive_heat_soak",
	"beacon_adaptive_heat_soak_max_wait",
	"beacon_adaptive_heat_soak_extra_wait_after_completion",
	"beacon_adaptive_heat_soak_layer_quality",
	"beacon_adaptive_heat_soak_maximum_first_layer_duration",
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% else %}
	{% set vars = (
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% endif %}
	{% set action = "show" if params|length == 0 else params2.ACTION %}
	{% if action is defined and params|length > 1 %}
	{ action_raise_error("ACTION cannot be specified with other parameters.") }
	{% elif action is not defined %}
	{% for k, v in params2.items() %}
	{% set k = k|lower %}
	{% if k in vars %}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Setting {k} to {v}"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={k} VALUE={v}
	{% else %}
	{ action_raise_error("Parameter '%s' is not recognised. Note that adaptive heatsoaking settings can only be set when a beacon probe is configured." % k) }
	{% endif %}
	{% endfor %}
	{% elif action == "reset" %}
	_RESET_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	CONSOLE_ECHO MSG="Heatsoak settings have been reset to their original values."
	{% elif action == "show" %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% set is_adaptive = False if not has_beacon else current.beacon_adaptive_heat_soak|default("")|lower == "true" %}
	{% if is_adaptive %}
	{% set quality = current.beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set first_layer_duration_secs = current.beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."
	{% elif current.bed_heat_soak_time|default(0)|int > 0 %}
	{% set duration_mins = (current.bed_heat_soak_time|int / 60.0) %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% else %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% endif %}
	{% if verbose %}
	CONSOLE_ECHO MSG="Detailed settings:"
	_SHOW_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	{% endif %}
	{% else %}
	{ action_raise_error("Action '%s' is not recognised" % action) }
	{% endif %}

[gcode_macro _LED_START_PRINTING]
gcode = 
	_LED_ACTION

[gcode_macro _LED_START_PRINTING_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_PRINTING]
gcode = 
	_LED_ON TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_PAUSE]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_ON]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_OFF]
gcode = 
	_LED_STANDBY

[gcode_macro _LED_LOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_LOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_RUNOUT]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_CLOG]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_UNLOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_UNLOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_DEACTIVATE_TOOLHEAD]
gcode = 
	_LED_OFF TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_STANDBY]
gcode = 
	_LED_STANDBY TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_WAKEUP]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_MOTORS_OFF]
gcode = 
	_LED_STANDBY
	_LED_VAOC_OFF

[gcode_macro _LED_INPUT_SHAPER_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_INPUT_SHAPER_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_BEACON_CALIBRATION_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_VAOC_ON]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=1.0 GREEN=1.0 BLUE=1.0
	{% endif %}

[gcode_macro _LED_VAOC_OFF]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=0.0 GREEN=0.0 BLUE=0.0
	{% endif %}

[gcode_macro _LED_ACTION]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_action %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SUCCESS]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_success %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_HEATING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_heating %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_COOLING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_cooling %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ERROR]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_error %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ON]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_on %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_OFF]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_off %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_STANDBY]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_standby %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}
	
	{% if toolhead >= 0 %}
	{% if printer['neopixel nozzle_led_t%s' % toolhead] is defined  %}
	SET_LED LED={'nozzle_led_t%s' % toolhead} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% else %}
	{% if printer['neopixel nozzle_led_t0'] is defined  %}
	SET_LED LED={'nozzle_led_t0'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% if printer['neopixel nozzle_led_t1'] is defined %}
	SET_LED LED={'nozzle_led_t1'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% endif %}
	
	_USER_LED_SET { rawparams }

[gcode_macro _USER_LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}

[gcode_macro LOAD_FILAMENT]
description = Loads new filament. Note: be careful with PETG, make sure you inspect the tip of your filament before loading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% if filament_name == '' or filament_type == '' %}
	{% set filament_name = 'unknown' %}
	{% set filament_type = 'unknown' %}
	{% endif %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_LOAD_FILAMENT TEMP={temp} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_LOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_LOAD_FILAMENT]
description = Load filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_LOAD_FILAMENT" MSG="TEMP={temp}"
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=load_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	_LOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	
	
	RESTORE_GCODE_STATE NAME=load_state
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament load routine complete, please check that the filament was loaded correctly."

[gcode_macro _IDEX_LOAD_FILAMENT]
description = Load filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament into T{toolhead}..."
	
	DEBUG_ECHO PREFIX="_IDEX_LOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	_LOAD_FILAMENT TOOLHEAD={toolhead} TEMP={temp} AUTOMATED={automated}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="Filament load routine for T{toolhead} complete, please check that the filament was loaded correctly."

[gcode_macro _LOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default(false)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE TOOLHEAD={toolhead}
	_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into hotend.."
	G92 E0
	G0 E{extruder_gear_to_cooling_position_distance} F{extruder_load_speed}
	G92 E0
	M400
	RATOS_ECHO MSG="Filament loaded into hotend."

[gcode_macro _LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set load_speed = printer["gcode_macro T%s" % toolhead].filament_load_speed|float * 60 %}
	{% set filament_loading_nozzle_offset = printer["gcode_macro T%s" % toolhead].filament_loading_nozzle_offset|float %}
	{% set cooling_position_to_nozzle_distance = printer["gcode_macro T%s" % toolhead].cooling_position_to_nozzle_distance|float %}
	{% set purge_after_load = printer["gcode_macro T%s" % toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into nozzle... Please wait!"
	G92 E0
	
	G0 E{cooling_position_to_nozzle_distance + filament_loading_nozzle_offset} F{load_speed}
	G92 E0
	G4 P1000
	_PURGE_FILAMENT	TOOLHEAD={toolhead} E={purge_after_load}
	RATOS_ECHO MSG="Filament loaded into nozzle!"

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"
	
	
	{% set filament_grabbing_length = printer["gcode_macro T%s" % toolhead].filament_grabbing_length|float %}
	{% set filament_grabbing_speed = printer["gcode_macro T%s" % toolhead].filament_grabbing_speed|float %}
	{% set resume_after_insert = true if printer["gcode_macro T%s" % toolhead].resume_after_insert|default(true)|lower == 'true' else false %}
	{% set enable_insert_detection = true if printer["gcode_macro T%s" % toolhead].enable_insert_detection|default(true)|lower == 'true' else false %}
	
	
	{% set current_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	
	{% if enable_insert_detection %}
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="toolhead: {toolhead}, filament_grabbing_length: {filament_grabbing_length}, filament_grabbing_speed: {filament_grabbing_speed}, current_idex_mode: {current_idex_mode}"
	
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	RATOS_ECHO MSG="Filament inserted into T{toolhead}, loading..."
	
	
	FORCE_MOVE STEPPER={'extruder%s' % ('' if toolhead == 0 else toolhead)} DISTANCE={filament_grabbing_length} VELOCITY={filament_grabbing_speed}
	M400
	
	
	{% if printer.pause_resume.is_paused %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% if resume_after_insert %}
	RESUME
	{% endif %}
	{% else %}
	{% if not printer.virtual_sdcard.is_active %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"

[gcode_macro _PURGE_BEFORE_UNLOAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set purge_before_unload = printer["gcode_macro T%s" % toolhead].purge_before_unload|float %}
	
	DEBUG_ECHO PREFIX="_PURGE_BEFORE_UNLOAD" MSG="TOOLHEAD: {toolhead}"
	
	
	{% if purge_before_unload > 0 %}
	G92 E0
	G0 E{purge_before_unload} F300
	G92 E0
	M400
	{% endif %}

[gcode_macro _PURGE_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set e = params.E|int %}
	{% set r = params.R|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_PURGE_FILAMENT" MSG="TOOLHEAD: {toolhead}, E: {e}"
	
	
	{% if e > 0 %}
	
	
	G92 E0
	G0 E{e} F300
	G92 E0
	M400
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={0.4 if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={0.4 if toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * 0.4)}
	{% endif %}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if r > 0 %}
	G92 E0
	G0 E-{r} F300
	G92 E0
	M400
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro _MOVE_TO_LOADING_POSITION]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_MOVE_TO_LOADING_POSITION" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	
	G1 X{loading_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _CLEANING_MOVE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_CLEANING_MOVE" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].parking_position is defined and printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set parking_position = printer["gcode_macro T%s" % toolhead].parking_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	{% set cleaning_position = loading_position %}
	{% if loading_position == parking_position %}
	{% if loading_position > 0 %}
	{% set cleaning_position = loading_position - 30 %}
	{% else %}
	{% set cleaning_position = loading_position + 30 %}
	{% endif %}
	{% endif %}
	
	
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _BED_MESH_SANITY_CHECK]
gcode = 
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is defined %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_start_print_true_zero_fuzzy_position %}
	CONSOLE_ECHO TYPE="error" TITLE="Defined zero reference not compatible with fuzzy true zero" MSG="Using fuzzy start print true zero position is not compatible with a defined zero_reference_position value in the [bed_mesh] section in printer.cfg._N_Please remove the zero_reference_position value from the [bed_mesh] section, or disable fuzzy true zero position in printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_start_print_true_zero_fuzzy_position: False"
	_STOP_AND_RAISE_ERROR MSG="Defined zero reference not compatible with fuzzy true zero"
	{% elif zero_ref_pos[0]|float|round != safe_home_x|float|round or zero_ref_pos[1]|float|round != safe_home_y|float|round %}
	CONSOLE_ECHO TYPE="error" TITLE="Zero reference position does not match safe home position" MSG="Please update your bed mesh zero reference position in printer.cfg, like so:_N__N_[bed_mesh]_N_zero_reference_position: {safe_home_x|float|round},{safe_home_y|float|round}_N_"
	_STOP_AND_RAISE_ERROR MSG="Zero reference position does not match safe home position"
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_bed_mesh %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact bed mesh is enabled" MSG="Beacon contact bed mesh is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_bed_mesh: False"
	{% endif %}
	
	{% if beacon_scan_method_automatic %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon 'automatic' scan method is enabled" MSG="Beacon 'automatic' scan method is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_scan_method_automatic: False"
	{% endif %}
	
	{% if beacon_contact_z_tilt_adjust %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact z-tilt adjust is enabled" MSG="Beacon contact z-tilt adjust is enabled. This is not recommended for normal use and may result in inaccurate z-tilt adjustment._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_z_tilt_adjust: False"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH]
gcode = 
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE=None
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE=None
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION {rawparams}
	{% endif %}

[gcode_macro _START_PRINT_BED_MESH]
variable_actual_true_zero_position_x = None
variable_actual_true_zero_position_y = None
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set X=[params.X0|default(-1)|float, params.X1|default(-1)|float] %}
	{% set Y=[params.Y0|default(-1)|float, params.Y1|default(-1)|float] %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_BED_MESH" MSG="idex_mode: {idex_mode}, X: {X}, Y: {Y}"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is not defined %}
	{% set zero_ref_pos = [safe_home_x if actual_true_zero_position_x is none else actual_true_zero_position_x, safe_home_y if actual_true_zero_position_y is none else actual_true_zero_position_y] %}
	{% endif %}
	
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	
	
	
	
	{% set X=[0, printable_x_max] %}
	{% endif %}
	
	
	{% set beacon_bed_mesh_scv = printer["gcode_macro RatOS"].beacon_bed_mesh_scv|default(25)|int %}
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% if printer.fastconfig.settings.beacon is defined and not beacon_contact_bed_mesh %}
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={beacon_bed_mesh_scv}
	{% endif %}
	
	
	{% set default_profile = printer["gcode_macro RatOS"].bed_mesh_profile|default('ratos') %}
	{% if printer["gcode_macro RatOS"].calibrate_bed_mesh|lower == 'true' %}
	BED_MESH_CLEAR
	{% if printer["gcode_macro RatOS"].adaptive_mesh|lower == 'true' %}
	CALIBRATE_ADAPTIVE_MESH PROFILE="{default_profile}" X0={X[0]} X1={X[1]} Y0={Y[0]} Y1={Y[1]} T={params.T|int} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={idex_mode} ZERO_REF_POS_X={zero_ref_pos[0]} ZERO_REF_POS_Y={zero_ref_pos[1]}
	{% else %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	BED_MESH_PROFILE LOAD="{default_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	
	{% elif printer["gcode_macro RatOS"].bed_mesh_profile is defined %}
	BED_MESH_CLEAR
	BED_MESH_PROFILE LOAD="{printer["gcode_macro RatOS"].bed_mesh_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"

[gcode_macro CALIBRATE_ADAPTIVE_MESH]
gcode = 
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set default_profile = params.PROFILE %}
	
	
	{% set x0 = params.X0|default(-1)|float %}
	{% set y0 = params.Y0|default(-1)|float %}
	{% set x1 = params.X1|default(-1)|float %}
	{% set y1 = params.Y1|default(-1)|float %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Received coordinates X0={x0|round(1)} Y0={y0|round(1)} X1={x1|round(1)} Y1={y1|round(1)}"
	
	{% if x0 >= x1 or y0 >= y1 %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Invalid coordinates received. Please check your slicer settings. Falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	
	
	{% if params.ZERO_REF_POS_X is defined and params.ZERO_REF_POS_Y is defined %}
	{% set zero_ref_pos_x = params.ZERO_REF_POS_X|float %}
	{% set zero_ref_pos_y = params.ZERO_REF_POS_Y|float %}
	{% if zero_ref_pos_x < x0 or zero_ref_pos_x > x1 or zero_ref_pos_y < y0 or zero_ref_pos_y > y1 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Zero reference position X={zero_ref_pos_x|round(1)} Y={zero_ref_pos_y|round(1)} is outside the mesh region, expanding mesh region to include it."
	{% set x0 = [x0, zero_ref_pos_x]|min %}
	{% set y0 = [y0, zero_ref_pos_y]|min %}
	{% set x1 = [x1, zero_ref_pos_x]|max %}
	{% set y1 = [y1, zero_ref_pos_y]|max %}
	{% endif %}
	{% endif %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float %}
	
	
	{% set mesh_x0 = [[x0, max_x]|min, min_x]|max %}
	{% set mesh_y0 = [[y0, max_y]|min, min_y]|max %}
	{% set mesh_x1 = [[x1, max_x]|min, min_x]|max %}
	{% set mesh_y1 = [[y1, max_y]|min, min_y]|max %}
	
	{% if mesh_x0 == min_x and mesh_y0 == min_y and mesh_x1 == max_x and mesh_y1 == max_y %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Print is using the full bed, falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	
	{% set probe_count_x = mesh_config.probe_count.split(",")[0]|int %}
	{% if mesh_config.probe_count.split(",")|length == 2 %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[1]|int %}
	{% else %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[0]|int %}
	{% endif %}
	
	
	{% set probe_x_step = (max_x - min_x) / probe_count_x %}
	{% set probe_y_step = (max_y - min_y) / probe_count_y %}
	
	
	{% set mesh_count_x = ([(mesh_x1 - mesh_x0) / probe_x_step, 3]|max)|int %}
	{% set mesh_count_y = ([(mesh_y1 - mesh_y0) / probe_y_step, 3]|max)|int %}
	{% set min_mesh_count = [mesh_count_x, mesh_count_y]|min %}
	{% set max_mesh_count = [mesh_count_x, mesh_count_y]|max %}
	
	
	{% set algorithm = mesh_config.algorithm %}
	{% if algorithm|lower == 'lagrange' and max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="cannot exceed a probe_count of 6 when using lagrange interpolation. Falling back to bicubic interpolation."
	{% set algorithm = 'bicubic' %}
	{% endif %}
	{% if algorithm|lower == 'bicubic' and min_mesh_count < 4 %}
	{% if max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="invalid probe_count option when using bicubic interpolation. Combination of 3 points on one axis with more than 6 on another is not permitted. Forcing minimum mesh count to be 4."
	{% set min_mesh_count = 4 %}
	{% else %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="bicubic interpolation with a probe_count of less than 4 points detected. Forcing lagrange interpolation."
	{% set algorithm = 'lagrange' %}
	{% endif %}
	{% endif %}
	
	{% set mesh_count_x = ([min_mesh_count, mesh_count_x]|max)|int %}
	{% set mesh_count_x = ([max_mesh_count, mesh_count_x]|min)|int %}
	{% set mesh_count_y = ([min_mesh_count, mesh_count_y]|max)|int %}
	{% set mesh_count_y = ([max_mesh_count, mesh_count_y]|min)|int %}
	
	{% set should_prime = printer["gcode_macro RatOS"].nozzle_priming == 'primeblob' %}
	{% if printer["dual_carriage"] is not defined %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% else %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 != 0 and probe_first %}
	{% set probe_first = false %}
	{% elif printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 == 0 and not probe_first %}
	{% set probe_first = true %}
	{% endif %}
	
	
	{% if should_prime and probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="mesh coordinates X0={mesh_x0|round(1)} Y0={mesh_y0|round(1)} X1={mesh_x1|round(1)} Y1={mesh_y1|round(1)}"
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y} RELATIVE_REFERENCE_INDEX=-1
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	
	
	{% if should_prime and not probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro M84]
rename_existing = M84.1
gcode = 
	
	M84.1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_OFFSET X=0 Y=0
	
	
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro _VAOC"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False
	{% endif %}
	
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	SET_SKEW CLEAR=1
	
	
	_LED_MOTORS_OFF

[gcode_macro M104]
rename_existing = M104.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M104" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set temperature_offset_t0 = printer["gcode_macro T0"].temperature_offset|default(0)|int %}
	{% set temperature_offset_t1 = printer["gcode_macro T1"].temperature_offset|default(0)|int %}
	{% set s0 = [s + temperature_offset_t0, 0]|max %}
	{% set s1 = [s + temperature_offset_t1, 0]|max %}
	{% if temperature_offset_t0 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t0}°C added to toolhead T0."
	{% endif %}
	{% if temperature_offset_t1 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t1}°C added to toolhead T1."
	{% endif %}
	{% else %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	M104.1 S{s0} T0
	M104.1 S{s1} T1
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% else %}
	M104.1 S{s} T{t}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M109]
rename_existing = M109.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M109" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M109" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	M109.1 S{s} T{t}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro SET_HEATER_TEMPERATURE]
rename_existing = SET_HEATER_TEMPERATURE_BASE
gcode = 
	
	{% set heater = params.HEATER|default("") %}
	{% set target = params.TARGET|default(0)|int %}
	
	DEBUG_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="heater: {heater}, target: {target}"
	
	{% set t = -1 %}
	{% if heater|lower == "extruder" or heater|lower == "extruder1" %}
	
	{% set t = 0 if heater|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and target > 0 %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set target = [target + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE_BASE HEATER="{heater}" TARGET={target}
	
	{% if t != -1 and printer.fastconfig.settings.beacon is defined %}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro TEMPERATURE_WAIT]
rename_existing = TEMPERATURE_WAIT_BASE
gcode = 
	
	{% set sensor = params.SENSOR|default("") %}
	{% set minimum = params.MINIMUM|default(-1)|int %}
	{% set maximum = params.MAXIMUM|default(-1)|int %}
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="sensor: {sensor}, minimum: {minimum}, maximum: {maximum}"
	
	{% set t = -1 %}
	{% if sensor|lower == "extruder" or sensor|lower == "extruder1" %}
	
	{% set t = 0 if sensor|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and (minimum > 0 or maximum > 0) %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% if minimum > -1 %}
	{% set minimum = [minimum + temperature_offset, 0]|max %}
	{% endif %}
	{% if maximum > -1 %}
	{% set maximum = [maximum + temperature_offset, 0]|max %}
	{% endif %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set id = "sensor " ~ sensor if t == -1 else "toolhead T" ~ t %}
	
	
	{% if minimum > -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum} MAXIMUM={maximum}
	{% elif minimum > -1 and maximum == -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum}
	{% elif minimum == -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MAXIMUM={maximum}
	{% else %}
	
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="neither MINIMUM or MAXIMUM args were specified, call TEMPERATURE_WAIT_BASE is expected to fail"
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}"
	{% endif %}
	
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature for {id} reached."

[gcode_macro SDCARD_PRINT_FILE]
rename_existing = SDCARD_PRINT_FILE_BASE
gcode = 
	{% if printer["ratos"] is defined %}
	PROCESS_GCODE_FILE { rawparams }
	{% else %}
	SDCARD_PRINT_FILE_BASE { rawparams }
	{% endif %}

[gcode_macro SKEW_PROFILE]
rename_existing = SKEW_PROFILE_BASE
variable_loaded_profile = ""
gcode = 
	{% if params.LOAD is defined %}
	{% if printer.fastconfig.settings["skew_correction %s" % params.LOAD] is defined %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='"{params.LOAD}"'
	{% endif %}
	{% endif %}
	
	SKEW_PROFILE_BASE { rawparams }

[gcode_macro SET_SKEW]
rename_existing = SET_SKEW_BASE
gcode = 
	{% if params.CLEAR is defined %}
	{% if params.CLEAR|default(0)|int == 1 %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='""'
	{% endif %}
	{% endif %}
	
	SET_SKEW_BASE { rawparams }

[gcode_macro SET_VELOCITY_LIMIT]
rename_existing = SET_VELOCITY_LIMIT_BASE
gcode = 
	{% if params.ACCEL_TO_DECEL is defined %}
	
	{% if params.ACCEL is defined %}
	{% set accel = params.ACCEL|float %}
	{% else %}
	{% set accel = printer.toolhead.max_accel|float %}
	{% endif %}
	
	{% if params.VELOCITY is defined %}
	{% set velocity = params.VELOCITY|float %}
	{% else %}
	{% set velocity = printer.toolhead.max_velocity|float %}
	{% endif %}
	
	{% if params.SQUARE_CORNER_VELOCITY is defined %}
	{% set scv = params.SQUARE_CORNER_VELOCITY|float %}
	{% else %}
	{% set scv = printer.toolhead.square_corner_velocity|float %}
	{% endif %}
	
	{% set mcr = params.ACCEL_TO_DECEL|float / accel %}
	
	DEBUG_ECHO PREFIX="SET_VELOCITY_LIMIT" MSG="ACCEL={accel}, VELOCITY={velocity}, SQUARE_CORNER_VELOCITY={scv}, MINIMUM_CRUISE_RATIO={mcr}"
	
	SET_VELOCITY_LIMIT_BASE ACCEL={accel} VELOCITY={velocity} SQUARE_CORNER_VELOCITY={scv} MINIMUM_CRUISE_RATIO={1-mcr}
	
	{% else %}
	
	SET_VELOCITY_LIMIT_BASE { rawparams }
	
	{% endif %}

[gcode_macro BED_MESH_CALIBRATE]
rename_existing = _BED_MESH_CALIBRATE_BASE
variable_abl_and_home_z_if_required = True
gcode = 
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	{% if abl_and_home_z_if_required %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% endif %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set beacon_default_probe_method = printer.fastconfig.settings.beacon.default_probe_method|default('proximity') %}
	{% set probe_method = params.PROBE_METHOD|default(beacon_default_probe_method)|lower %}
	{% if probe_method == 'proximity' %}
	_CHECK_ACTIVE_BEACON_MODEL_TEMP TITLE="Bed mesh calibration warning"
	{% endif %}
	{% endif %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_BED_MESH_CALIBRATE_BASE {rawparams}
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	_APPLY_RATOS_BED_MESH_PARAMETERS {rawparams}
	{% endif %}

[gcode_macro SET_GCODE_OFFSET]
rename_existing = SET_GCODE_OFFSET_BASE
gcode = 
	DEBUG_ECHO PREFIX="SET_GCODE_OFFSET" MSG="{rawparams|replace('"', '')|replace("'", '')}"
	{% set z_before = printer.gcode_move.homing_origin.z|float %}
	SET_GCODE_OFFSET_BASE {rawparams}
	_AFTER_SET_GCODE_OFFSET Z_BEFORE={z_before}

[gcode_macro _AFTER_SET_GCODE_OFFSET]
gcode = 
	{% set z_before = params.Z_BEFORE|float %}
	{% set z_after = printer.gcode_move.homing_origin.z|float %}
	{% if z_before != z_after %}
	_ALERT_NON_ZERO_Z_OFFSET FORCE=1
	{% endif %}

[gcode_macro _START_PRINT_PARK]
gcode = 
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_x = printer["gcode_macro RatOS"].start_print_park_x %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% if printer["gcode_macro RatOS"].start_print_park_x is defined and printer["gcode_macro RatOS"].start_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="start_print_park_x is ignored for IDEX printers"
	{% endif %}
	PARK_TOOLHEAD
	G90
	{% endif %}
	
	
	_PARK LOCATION={start_print_park_in} X={start_print_park_x}
	G0 Z{z} F{z_speed}

[gcode_macro _END_PRINT_PARK]
gcode = 
	{% if printer["dual_carriage"] is defined %}
	
	{% if printer["gcode_macro RatOS"].end_print_park_x is defined and printer["gcode_macro RatOS"].end_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="end_print_park_x is ignored for IDEX printers"
	{% endif %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	PARK_TOOLHEAD
	G90
	{% endif %}
	_PARK LOCATION={printer["gcode_macro RatOS"].end_print_park_in} X={printer["gcode_macro RatOS"].end_print_park_x}

[gcode_macro _PARK]
gcode = 
	
	{% set x = params.X %}
	{% set location = params.LOCATION|default('back')|lower %}
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	{% set nozzle_priming = printer["gcode_macro RatOS"].nozzle_priming|lower %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="park"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% if x != '' %}
	{% if x|float >= printer.toolhead.axis_minimum.x + 5 and x|float <= printable_x_max - 5 %}
	{% set park_x = x|float %}
	{% else %}
	{action_respond_info('The requested X co-ordinate is outside the defined axis bounds - using defaults')}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	{% else %}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	
	
	{% set park_y = printable_y_max - 15 %}
	{% if location == 'front' %}
	{% set park_y = printer.toolhead.axis_minimum.y + 5 %}
	{% elif location == 'center' %}
	{% set park_y = printable_y_max / 2 %}
	{% elif location == 'primeblob' and printer["dual_carriage"] is defined %}
	
	{% set park_y = printable_y_max - 15 %}
	{% endif %}
	
	
	{% if location == 'primeblob' and printer["dual_carriage"] is not defined %}
	{% if (nozzle_priming == 'primeblob' or nozzle_priming == 'primeline') %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set park_x = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set park_x = printable_x_max - 5 %}
	{% else %}
	{% set park_x = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set park_y = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set park_y = printable_y_max - 5 %}
	{% else %}
	{% set park_y = nozzle_prime_start_y|float %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	G0 X{park_x} Y{park_y} F{speed}
	{% else %}
	
	G0 Y{park_y} F{speed}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="park"

[gcode_macro SAVE_PROBE_RESULT]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	{% set last_z_offset = 9999.9 %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if beacon_contact_prime_probing %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	{% else %}
	{% set last_z_offset = printer.beacon.last_sample.dist - current_z %}
	{% endif %}
	{% elif printer.fastconfig.settings.bltouch is defined  %}
	{% set config_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% elif printer.fastconfig.settings.probe is defined  %}
	{% set config_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% endif %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Saving offset adjustment of {last_z_offset} in {params.VARIABLE|default('last_z_offset')}"
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={params.VARIABLE|default('last_z_offset')} VALUE={last_z_offset}

[gcode_macro PROBE_FOR_PRIMING]
gcode = 
	
	{% set probe_for_priming_disable_mesh_constraints = true if printer["gcode_macro RatOS"].probe_for_priming_disable_mesh_constraints|default(false)|lower == 'true' else false %}
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower != 'false' %}
	SAVE_GCODE_STATE NAME=probe_for_priming_state
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the prime location.."
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set t = params.TOOLHEAD|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% if idex_mode == '' %}
	
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% if t == 0 %}
	{% set x_start = 5 %}
	{% else %}
	{% set x_start = printable_x_max - 5 %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% endif %}
	{% endif %}
	{% set z = printer.fastconfig.settings.bed_mesh.horizontal_move_z|float %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% if printer.fastconfig.settings.bltouch is defined %}
	{% set x_offset = printer.fastconfig.settings.bltouch.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.bltouch.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% elif printer.fastconfig.settings.probe is defined %}
	{% set x_offset = printer.fastconfig.settings.probe.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.probe.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% elif printer.fastconfig.settings.beacon is defined %}
	{% set x_offset = printer.fastconfig.settings.beacon.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.beacon.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.beacon.trigger_distance|float %}
	{% else %}
	{ action_raise_error("No probe, beacon or bltouch section found. Adaptive priming only works with a [probe], [beacon] or [bltouch] section defined.") }
	{% endif %}
	
	{% if z < z_offset %}
	{ action_raise_error("Horizontal move Z ({z}) is below your probe's Z offset ({z_offset}). Please adjust your horizontal_move_z setting in [bed_mesh] to be above {z}.") }
	{% endif %}
	
	{% if not probe_for_priming_disable_mesh_constraints %}
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float - x_offset %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float - y_offset %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float - x_offset %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float - y_offset %}
	
	
	{% set x_start = [[x_start, max_x]|min, min_x]|max %}
	{% set y_start = [[y_start, max_y]|min, min_y]|max %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the start of the prime location at {x_start}, {y_start}"
	
	G90
	
	M83
	
	G0 Z{z} F{z_speed}
	
	G1 X{x_start} Y{y_start} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result
	{% endif %}
	
	{% if idex_mode == '' %}
	
	{% set x_end = x_start %}
	{% set y_end = y_start + 45 %}
	{% else %}
	
	{% if t==1 %}
	{% set x_end = x_start - 45 %}
	{% else %}
	{% set x_end = x_start + 45 %}
	{% endif %}
	{% set y_end = y_start %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the end of the prime location at {x_end}, {y_end}"
	G1 X{x_end} Y{y_end} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result
	{% endif %}
	
	RESTORE_GCODE_STATE NAME=probe_for_priming_state
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	{% endif %}

[gcode_macro RESET_PRIME_PROBE_STATE]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result VALUE=None
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result_t1 VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result_t1 VALUE=None
	{% endif %}

[gcode_macro PROBE_CURRENT_POSITION]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	SAVE_GCODE_STATE NAME=probe_current_position_state
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	ASSERT_PROBE_DEPLOYED
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_prime_probing %}
	PROBE PROBE_METHOD=contact SAMPLES=1
	{% else %}
	PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	BEACON_QUERY
	{% else %}
	
	RESTORE_GCODE_STATE NAME=probe_current_position_state MOVE=1 MOVE_SPEED={printer["gcode_macro RatOS"].macro_z_speed|float}
	{% endif %}

[gcode_macro PRIME_BLOB]
description = Prints a primeblob, used internally, if configured, as part of the START_PRINT macro.
variable_x_offset = 5
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="prime_blob"
	SET_MACRO_TRAVEL_SETTINGS
	
	RATOS_ECHO PREFIX="Priming" MSG="Priming nozzle with prime blob.."
	
	
	{% set current_toolhead = 0 %}
	
	
	{% set target_idex_mode = '' %}
	{% set extruder = 'extruder' %}
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE is defined %}
	{% set target_idex_mode = params.IDEX_MODE|default('')|lower %}
	{% else %}
	{ action_raise_error("IDEX_MODE parameter not found for PRIME_BLOB macro. This is likely a bug.") }
	{% endif %}
	RATOS_ECHO PREFIX="Priming" MSG="Priming in IDEX {target_idex_mode} mode.."
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set current_toolhead = 1 if current_idex_mode=='primary' else 0 %}
	{% set extruder = 'extruder1' if current_toolhead == 1 else 'extruder' %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	SAVE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set fan_speed = printer["gcode_macro RatOS"].nozzle_prime_bridge_fan|float %}
	{% set nozzle_diameter = printer.fastconfig.settings[extruder].nozzle_diameter|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set has_start_offset_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) != 9999.9 %}
	{% if printer["dual_carriage"] is defined %}
	{% set has_start_offset_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) != 9999.9 %}
	{% endif %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_z_height = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set nozzle_prime_direction = printer["gcode_macro RatOS"].nozzle_prime_direction|lower %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% if target_idex_mode == '' %}
	
	{% set x_factor = 0 %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% set y_factor = -1 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% if nozzle_prime_start_y|float < printable_y_max / 2 %}
	{% set y_factor = 1 %}
	{% else %}
	{% set y_factor = -1 %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_direction == 'forwards' %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_direction == 'backwards' %}
	{% set y_factor = -1 %}
	{% endif %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% else %}
	{% set z = start_print_park_z_height %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% set y_factor = 0 %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set x_start = center_x / 2 + 5 %}
	{% set x_factor = 1 %}
	{% else %}
	
	
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% if current_toolhead == 0 %}
	{% set x_start = 55 %}
	{% set x_factor = -1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 55 %}
	{% set x_factor = 1 %}
	{% endif %}
	{% else %}
	{% if current_toolhead == 0 %}
	{% set x_start = 5 %}
	{% set x_factor = 1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 5 %}
	{% set x_factor = -1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_x_max - 5 %}
	{% endif %}
	{% set z = 10 %}
	{% endif %}
	
	{% set start_z_offset = 0 %}
	{% set end_z_offset = 0 %}
	{% if has_start_offset_t0 %}
	{% set start_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) %}
	{% set end_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_end_result|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t0) ) }
	{% endif %}
	{% if end_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t0) )  }
	{% endif %}
	{% set start_z_offset = start_z_probe_result_t0 %}
	{% set end_z_offset = end_z_probe_result_t0 %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	{% if current_toolhead == 1 or both_toolheads or target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	{% if has_start_offset_t1 %}
	{% set start_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) %}
	{% set end_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_end_result_t1|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t1) ) }
	{% endif %}
	{% if end_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t1) ) }
	{% endif %}
	{% set start_z_offset = [start_z_offset, start_z_probe_result_t1]|max %}
	{% set end_z_offset = [end_z_offset, start_z_probe_result_t1]|max %}
	{% endif %}
	{% endif %}
	{% if target_idex_mode != 'copy' and target_idex_mode != 'mirror' %}
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% set original_start_z_offset = start_z_offset %}
	{% set original_end_z_offset = end_z_offset %}
	{% set start_z_offset = original_end_z_offset %}
	{% set end_z_offset = original_start_z_offset %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	DEBUG_ECHO PREFIX="PRIME_BLOB" MSG="x_start: {x_start}, y_start: {y_start}, x_factor: {x_factor}, y_factor: {y_factor}, z: {z}, start_z_offset: {start_z_offset}, end_z_offset: {end_z_offset}"
	
	
	G90
	
	M83
	RATOS_ECHO PREFIX="Priming" MSG="Lifting Z to {z}.."
	
	G0 Z{z} F{z_speed}
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% if start_print_park_in != 'primeblob' %}
	G1 X{x_start} F{speed}
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% endif %}
	{% else %}
	
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% if target_idex_mode=="copy" or target_idex_mode=="mirror" %}
	RATOS_ECHO PREFIX="Priming" MSG="Mirroring move to {x_start}, {y_start} along the edge of the print area.."
	
	_IDEX_MIRROR PRIMING=1
	{% else %}
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% endif %}
	G1 X{x_start} F{speed}
	{% endif %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Starting prime blob.."
	
	G1 Z{0.5 + start_z_offset} F{z_speed}
	
	G1 Y{y_start} F{speed}
	
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	
	M106 S{fan_speed}
	
	G1 Z5 F100 E5
	G92 E0
	RATOS_ECHO PREFIX="Priming" MSG="Bridging with {((fan_speed/255) * 100)|int}% fan speed.."
	
	G1 F3000 X{x_start + (15 * x_factor)} Y{y_start + (15 * y_factor)} E{1 / ((0.4 / nozzle_diameter) ** 2)}
	
	
	
	G1 F3000 X{x_start + (20 * x_factor)} Y{y_start + (20 * y_factor)} Z{3.8 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (34 * x_factor)} Y{y_start + (34 * y_factor)} Z{2.6 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (38 * x_factor)} Y{y_start + (38 * y_factor)} Z{1.4 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (42 * x_factor)} Y{y_start + (42 * y_factor)} Z{0.2 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	
	M106 S0
	
	G1 F3000 X{x_start + (46 * x_factor)} Y{y_start + (46 * y_factor)} Z{0.2 + end_z_offset} E0.6
	
	G1 F{speed} X{x_start + (50 * x_factor)} Y{y_start + (50 * y_factor)}
	
	
	{% if target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if target_idex_mode == "copy" %}
	{% if first_y >= 0 %}
	_IDEX_COPY DANCE=0 Y={first_y}
	{% else %}
	_IDEX_COPY DANCE=0 Y={params.Y1}
	{% endif %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	RESTORE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="prime_blob"
	
	
	G92 E0

[gcode_macro UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set temp = params.TEMP|default(220)|int %}
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_UNLOAD_FILAMENT TEMP={temp} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_UNLOAD_FILAMENT]
description = Unload filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_UNLOAD_FILAMENT" MSG="TEMP: {temp}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=unload_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	G4 P3000
	
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD=0 NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=unload_state
	
	
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament unloading completed"

[gcode_macro _IDEX_UNLOAD_FILAMENT]
description = Unload filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading T{toolhead} filament..."
	
	DEBUG_ECHO PREFIX="_IDEX_UNLOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} AUTOMATED={automated}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="T{toolhead} filament unloading completed"

[gcode_macro _UNLOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LEGACY_UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
gcode = 
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set unload_speed = 5 * 60 %}
	{% set unload_length = printer["gcode_macro RatOS"].filament_unload_length|float %}
	M117 Unloading filament...
	
	G0 E10 F300
	
	G0 E-5 F3600
	
	G4 P3000
	
	G0 E5 F6000
	
	G0 E-15 F6000
	
	G0 E-{unload_length} F{unload_speed}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}
	M117 Filament unloaded!
	RESPOND MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	RATOS_ECHO MSG="Unloading filament from nozzle to cooling zone... Please wait!"
	
	_PURGE_BEFORE_UNLOAD TOOLHEAD={toolhead}
	
	{% if printer["gcode_macro _UNLOAD_WITHOUT_TIP_FORMING"] is defined %}
	
	_UNLOAD_WITHOUT_TIP_FORMING TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	_UNLOAD_WITH_TIP_FORMING NAME='{filament_name}' TYPE='{filament_type}'
	{% endif %}
	
	G4 P3000

[gcode_macro _UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	{% set tooolhead_sensor_to_extruder_gear_distance = printer["gcode_macro T%s" % toolhead].tooolhead_sensor_to_extruder_gear_distance|float %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER" MSG="TOOLHEAD: {toolhead}"
	
	
	G0 E-{extruder_gear_to_cooling_position_distance + tooolhead_sensor_to_extruder_gear_distance + 50} F{extruder_load_speed}
	
	RATOS_ECHO MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_WITH_TIP_FORMING]
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	{% if filament_name != '' and filament_type != '' %}
	_UNLOAD_KNOWN_FILAMENT NAME={filament_name} TYPE={filament_type}
	{% else %}
	_UNLOAD_UNKNOWN_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _UNLOAD_KNOWN_FILAMENT]
description = User overrideable tip forming macro if slicer filament profiles are known
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	RATOS_ECHO PREFIX="FILAMENT TYPE" MSG='{filament_type}'
	RATOS_ECHO PREFIX="FILAMENT PROFILE" MSG='{filament_name}'
	
	
	{% if filament_name == "Prusament PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% elif filament_name == "Nobufil PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% else %}
	
	RATOS_ECHO PREFIX="_UNLOAD_KNOWN_FILAMENT" MSG="Filament profile not found!"
	_UNLOAD_UNKNOWN_FILAMENT
	{% endif %}

[gcode_macro _UNLOAD_UNKNOWN_FILAMENT]
description = User overrideable standard tip forming macro
gcode = 
	
	DEBUG_ECHO PREFIX="_UNLOAD_UNKNOWN_FILAMENT" MSG="Using standard tip forming macro!"
	
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10

[gcode_macro _TIP_FORMING]
gcode = 
	
	{% set cooling_moves = params.COOLING_MOVES|default(4)|int %}
	{% set cooling_move_length = params.COOLING_MOVE_LENGTH|default(10)|float %}
	{% set start_cooling_speed = params.START_COOLING_SPEED|default(10)|float * 60 %}
	{% set end_cooling_speed = params.END_COOLING_SPEED|default(50)|float * 60 %}
	{% if cooling_moves == 0 %}
	{% set cooling_move_length = 0 %}
	{% endif %}
	
	
	{% set dip = true if params.DIP|default(false)|lower == "true" else false %}
	{% set dip_length = params.DIP_LENGTH|default(22)|float %}
	{% set dip_speed = params.DIP_SPEED|default(30)|float * 60 %}
	{% set dip_retract_speed = params.DIP_RETRACT_SPEED|default(70)|float * 60 %}
	
	
	{% set retract_length = params.RETRACT_LENGTH|default(18)|float %}
	{% set start_retract_speed = params.START_RETRACT_SPEED|default(120)|float * 60 %}
	{% set end_retract_speed = params.END_RETRACT_SPEED|default(20)|float * 60 %}
	
	DEBUG_ECHO PREFIX="_TIP_FORMING" MSG="cooling_moves: {cooling_moves}, cooling_move_length: {cooling_move_length}, start_cooling_speed: {start_cooling_speed}, end_cooling_speed: {end_cooling_speed}, dip: {dip}, dip_length: {dip_length}, dip_speed: {dip_speed}, dip_retract_speed: {dip_retract_speed}, retract_length: {retract_length}, start_retract_speed: {start_retract_speed}, end_retract_speed: {end_retract_speed}"
	
	M220 S100
	
	
	G92 E0
	{% set retract = retract_length + cooling_move_length / 2 - 15 %}
	G1 E-15 F{start_retract_speed}
	G1 E-{0.7 * retract} F{1.0 * end_retract_speed}
	G1 E-{0.2 * retract} F{0.5 * end_retract_speed}
	G1 E-{0.1 * retract} F{0.3 * end_retract_speed}
	
	
	G92 E0
	{% if cooling_moves > 0 %}
	{% set i = (end_cooling_speed - start_cooling_speed) / (2 * cooling_moves - 1) %}
	{% for m in range(cooling_moves) %}
	G1 E{cooling_move_length} F{(start_cooling_speed + i * m * 2)}
	G1 E-{cooling_move_length} F{(start_cooling_speed + i * (m * 2 + 1))}
	{% endfor %}
	{% endif %}
	
	
	G92 E0
	{% if dip %}
	G1 E{dip_length} F{dip_speed}
	G4 P100
	G1 E-{dip_length} F{dip_retract_speed}
	{% endif %}
	
	G92 E0
	M400

[delayed_gcode __ON_FILAMENT_SENSOR_BUTTON_PRESSED_STARTUP_GUARD]
initial_duration = 2.
gcode = 
	SET_GCODE_VARIABLE MACRO=_ON_FILAMENT_SENSOR_BUTTON_PRESSED VARIABLE=startup_complete VALUE=True

[gcode_macro _ON_FILAMENT_SENSOR_BUTTON_PRESSED]
variable_startup_complete = False
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set toolhead_sensor_button_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_sensor_button_only_when_sensor_enabled|default(false)|lower == 'true' %}
	
	
	{% if not startup_complete and sensor_enabled %}
	{action_emergency_stop("RatOS: The T%s filament sensor button was triggered immediately on printer startup. This is likely a false trigger. Please check your filament sensor wiring and configuration!" % (toolhead,))}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_SENSOR_BUTTON_PRESSED" MSG="TOOLHEAD: {toolhead}, SENSOR_ENABLED: {sensor_enabled}, TOOLHEAD_SENSOR_BUTTON_ONLY_WHEN_SENSOR_ENABLED: {toolhead_sensor_button_only_when_sensor_enabled}"
	
	{% if not printer.virtual_sdcard.is_active and (sensor_enabled or not toolhead_sensor_button_only_when_sensor_enabled) %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	{% set toolhead_detect_clog_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_detect_clog_only_when_sensor_enabled|default(true)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}, ENABLE_CLOG_DETECTION: {enable_clog_detection}, TOOLHEAD_DETECT_CLOG_ONLY_WHEN_SENSOR_ENABLED: {toolhead_detect_clog_only_when_sensor_enabled}, SENSOR_ENABLED: {sensor_enabled}"
	
	{% if enable_clog_detection and (sensor_enabled or not toolhead_detect_clog_only_when_sensor_enabled) %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_clog_detection %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_FILAMENT_END]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set clogged = true if params.CLOGGED|default(false)|lower == 'true' else false %}
	
	
	{% set unload_after_runout = printer["gcode_macro T%s" % toolhead].unload_after_runout|float %}
	
	
	{% if clogged %}
	_LED_FILAMENT_CLOG TOOLHEAD={toolhead}
	{% else %}
	_LED_FILAMENT_RUNOUT TOOLHEAD={toolhead}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_END" MSG="TOOLHEAD: {toolhead}"
	
	{% if printer.virtual_sdcard.is_active %}
	{% if not printer.pause_resume.is_paused %}
	PAUSE RUNOUT=True
	{% endif %}
	{% if not clogged and unload_after_runout %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	{% if not clogged and printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true'%}
	_JOIN_SPOOL TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M600]
description = Executes a color change by pausing the printer an unloading the filament.
gcode = 
	PAUSE
	UNLOAD_FILAMENT AUTOMATED=True
	RATOS_ECHO MSG="Please load new filament and resume"

[gcode_macro COLD_PULL]
description = Automated hotend cold pull.
gcode = 
	
	{% set extrusion_temp = params.EXTRUSION_TEMP|default(220)|int %}
	{% set cold_pull_temp = params.COLD_PULL_TEMP|default(80)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	
	{% if printer["dual_carriage"] is not defined %}
	{% set toolhead = 0 %}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead != 0 and toolhead != 1 %}
	{action_raise_error("Please select toolhead! 0 = left, 1 = right toolhead")}
	{% endif %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	RATOS_ECHO MSG="Starting cold pull on T{toolhead}..."
	{% else %}
	RATOS_ECHO MSG="Starting cold pull..."
	{% endif %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	SAVE_GCODE_STATE NAME=cold_pull_state
	
	
	{% if printer["dual_carriage"] is defined and "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	RATOS_ECHO MSG="Heating T{toolhead} to {extrusion_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={extrusion_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={extrusion_temp} MAXIMUM={extrusion_temp + 2}
	
	
	G4 P3000
	
	
	RATOS_ECHO MSG="extruding..."
	G92 E0
	G1 E30 F300
	G92 E0
	
	
	RATOS_ECHO MSG="Cooling T{toolhead} to {cold_pull_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={cold_pull_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={cold_pull_temp} MAXIMUM={cold_pull_temp + 2}
	
	
	G4 P10000
	
	
	RATOS_ECHO MSG="cold pull..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-40 VELOCITY=5 ACCEL=100
	
	
	RATOS_ECHO MSG="eject filament..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-200 VELOCITY=20 ACCEL=500
	
	
	RATOS_ECHO MSG="cooling down extruder..."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	RESTORE_GCODE_STATE NAME=cold_pull_state
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	
	CONSOLE_ECHO TITLE="Cold pull complete" MSG="Please remove the filament from the PTFE tube and cut the end off. Do NOT try to load it again." TYPE="warning"

[gcode_macro _USER_START_PRINT_BEFORE_HOMING]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_BED]
gcode = 

[gcode_macro _USER_START_PRINT_BED_MESH]
gcode = 

[gcode_macro _USER_START_PRINT_PARK]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 

[gcode_macro _USER_START_PRINT_HEAT_CHAMBER]
description = Uses the extruder sensor to wait for chamber temp. Override the _START_PRINT_HEAT_CHAMBER macro to implement heated chamber handling.
gcode = 
	
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}

[gcode_macro _USER_END_PRINT_BEFORE_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_AFTER_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_PARK]
gcode = 

[gcode_macro _USER_END_PRINT_FINISHED]
description = User hook for when the print is finished after gcode state has been restored.
gcode = 

[gcode_macro _USER_START_PRINT]
gcode = 

[gcode_macro _USER_END_START_PRINT]
gcode = 

[gcode_macro _USER_START_FEATURE]
gcode = 

[gcode_macro _USER_END_FEATURE]
gcode = 

[gcode_macro _USER_BEFORE_IDLE_TIMEOUT]
gcode = 

[gcode_macro _USER_AFTER_IDLE_TIMEOUT]
gcode = 

[gcode_macro ECHO_T_VARS]
description = Echo Toolhead variables to the console.
gcode = 
	{% set t = params.T|default(0) %}
	RATOS_ECHO MSG="T{t} Variables"
	{% for var, value in printer["gcode_macro T%s" % t].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ECHO_RATOS_VARS]
description = Echo RatOS variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro RatOS"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ENSURE_CRITICAL_RATOS_INIT]
variable_completed = False
gcode = 
	{% if not completed %}
	CALCULATE_PRINTABLE_AREA
	SET_GCODE_VARIABLE MACRO=ENSURE_CRITICAL_RATOS_INIT VARIABLE=completed VALUE=True
	{% endif %}

[delayed_gcode RATOS_INIT]
initial_duration = 0.1
gcode = 
	{action_respond_info("Initializing RatOS...")}
	ENSURE_CRITICAL_RATOS_INIT
	_LED_STANDBY
	INITIAL_FRONTEND_UPDATE
	_CHAMBER_FILTER_SANITY_CHECK
	{% if printer.fastconfig.settings.beacon is defined %}
	
	_BED_MESH_SANITY_CHECK
	{% endif %}
	{% set svv = printer.save_variables.variables %}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=0 C={svv.nozzle_expansion_coefficient_t0|default(0.06)|float}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=1 C={svv.nozzle_expansion_coefficient_t1|default(0.06)|float}
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=idex_applied_offset

[delayed_gcode RATOS_LOGO]
initial_duration = 2
gcode = 
	
	
	
	
	
	ENSURE_CRITICAL_RATOS_INIT
	HELLO_RATOS
	_ALERT_NON_ZERO_Z_OFFSET

[gcode_macro _ALERT_NON_ZERO_Z_OFFSET]
gcode = 
	{% set force = params.FORCE|default(0)|int == 1 %}
	{% set user_offset = printer.named_offsets.user_probe_z_offset.z|float %}
	{% set gcode_offset = printer.gcode_move.homing_origin.z|float %}
	{% set combined_offset = user_offset + gcode_offset %}
	
	{% if force or user_offset != 0 or gcode_offset != 0 %}
	{% set title = "User-adjusted Z-offset of %.3f mm is active" % combined_offset %}
	{% set msg = "" %}
	{% set nl = "" %}
	{% if user_offset != 0 %}
	{% set msg = msg + "beacon true zero user Z-offset: %.3f mm (to clear, use Z_OFFSET_APPLY_PROBE CLEAR=1)" % user_offset %}
	{% set nl = "_N_" %}
	{% endif %}
	{% if gcode_offset != 0 %}
	{% set msg = msg + nl + "G-code Z-offset: %.3f mm" % gcode_offset %}
	{% endif %}
	CONSOLE_ECHO TITLE="{title}" TYPE="info" MSG="{msg}"
	{% endif %}

[gcode_macro _INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE]
gcode = 
	{% set variable = params.VARIABLE|string %}
	{% set svv = printer.save_variables.variables %}
	{% set nlu_msg = "no longer used, please remove" %}
	{% if svv[variable] is defined %}
	{% set v = svv[variable]|string|replace('"', '')|replace("'", "") %}
	{% if not nlu_msg in v %}
	SAVE_VARIABLE VARIABLE={variable} VALUE='"{nlu_msg} (was {v})"'
	{% endif %}
	CONSOLE_ECHO TITLE="Deprecated ratos-variables.cfg variable" TYPE="warning" MSG="The variable {variable} is no longer used, please remove it from your ratos-variables.cfg file."
	{% endif %}

[gcode_macro _NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK]
gcode = 
	
	
	
	
	
	
	
	{% set t = params.T|int %}
	{% set c = params.C|float %}
	{% set normal_low = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_low|default(0.05)|float %}
	{% set normal_high = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_high|default(0.10)|float %}
	
	{% if c < 0 %}
	
	{action_emergency_stop("Invalid nozzle_expansion_coefficient_t%s value in ratos-variables.cfg: %.3f. It must be non-negative." % (t, c))}
	{% endif %}
	{% if c >= normal_high %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite high. Please verify that this is correct."
	{% endif %}
	{% if c <= normal_low %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite low. Please verify that this is correct."
	{% endif %}

[gcode_macro INITIAL_FRONTEND_UPDATE]
gcode = 
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_error = printer["gcode_macro RatOS"].status_color_error|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_unknown}"'
	{% endif %}
	
	
	{% set t0_sensor = "undefined" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	{% set t0_sensor = "detected" %}
	{% else %}
	{% set t0_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t0_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	{% set t1_sensor = "undefined" %}
	{% if printer["dual_carriage"] is defined and printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	{% set t1_sensor = "detected" %}
	{% else %}
	{% set t1_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t1_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	{% if svv.t0_filament is defined and printer["gcode_macro T0"] is defined %}
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	{% if t0_sensor != "empty" %}
	{% set t0_filament_type = svv.t0_filament[0]|default('')|string %}
	{% set t0_filament_name = svv.t0_filament[1]|default('')|string %}
	{% set t0_filament_temp = svv.t0_filament[2]|default(0)|float %}
	{% if t0_filament_name != '' and t0_filament_type != '' and t0_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{t0_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{t0_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={t0_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}
	{% if svv.t1_filament is defined and printer["gcode_macro T1"] is defined %}
	{% if printer["gcode_macro T1"].filament_name is defined and printer["gcode_macro T1"].filament_type is defined and printer["gcode_macro T1"].filament_temp is defined %}
	{% if t1_sensor != "empty" %}
	{% set t1_filament_type = svv.t1_filament[0]|default('')|string %}
	{% set t1_filament_name = svv.t1_filament[1]|default('')|string %}
	{% set t1_filament_temp = svv.t1_filament[2]|default(0)|float %}
	{% if t1_filament_name != '' and t1_filament_type != '' and t1_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='"{t1_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='"{t1_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE={t1_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t1_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro CALCULATE_PRINTABLE_AREA]
variable_calculated = False
gcode = 
	{% if not calculated %}
	{% set bed_margin_x = printer["gcode_macro RatOS"].bed_margin_x %}
	{% set bed_margin_y = printer["gcode_macro RatOS"].bed_margin_y %}
	
	
	
	{% set tool = 0 if printer["gcode_macro T0"] is not defined or printer["gcode_macro T0"].active else 1 %}
	{% set max_x = printer.toolhead.axis_maximum.x if printer["dual_carriage"] is defined and tool == 0 else printer.toolhead.axis_maximum.x - bed_margin_x[1] %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	
	
	{% set max_x = printer.toolhead.axis_maximum.x %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="printer.toolhead.axis_maximum.x {printer.toolhead.axis_maximum.x}"
	
	{% set max_y = printer.toolhead.axis_maximum.y - bed_margin_y[1]%}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_x_max VALUE={max_x}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_y_max VALUE={max_y}
	SET_GCODE_VARIABLE MACRO=CALCULATE_PRINTABLE_AREA VARIABLE=calculated VALUE=True
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	RATOS_LOG PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	{% endif %}

[gcode_macro CACHE_TOOLHEAD_SETTINGS]
variable_cache = {"global": {"accel": 1000, "ratio": 0.5, "speed": 50, "scv": 5}}
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set dummy = cache.__setitem__(key, {"accel": printer.toolhead.max_accel, "ratio": printer.toolhead.minimum_cruise_ratio, "speed": printer.toolhead.max_velocity, "scv": printer.toolhead.square_corner_velocity}) %}
	SET_GCODE_VARIABLE MACRO=CACHE_TOOLHEAD_SETTINGS VARIABLE=cache VALUE="{cache | pprint | replace("\n", "") | replace("\"", "\\\"")}"
	DEBUG_ECHO PREFIX="CACHE_TOOLHEAD_SETTINGS" MSG="Toolhead settings cached for {key}. {printer.toolhead.max_accel} accel, {printer.toolhead.minimum_cruise_ratio} ratio, {printer.toolhead.max_velocity} velocity, {printer.toolhead.square_corner_velocity} scv."

[gcode_macro RESTORE_TOOLHEAD_SETTINGS]
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set values = printer["gcode_macro CACHE_TOOLHEAD_SETTINGS"].cache.__getitem__(key) %}
	{% if values is not defined or values == 'None' %}
	{ action_raise_error("RESTORE_TOOLHEAD_SETTINGS: Toolhead settings not cached for key '" ~ key ~ "'.") }
	{% endif %}
	SET_VELOCITY_LIMIT ACCEL={values.accel} MINIMUM_CRUISE_RATIO={values.ratio} VELOCITY={values.speed} SQUARE_CORNER_VELOCITY={values.scv}
	DEBUG_ECHO PREFIX="RESTORE_TOOLHEAD_SETTINGS" MSG="Toolhead settings restored. {values.accel} accel, {values.ratio} ratio, {values.speed} velocity, {values.scv} scv."

[gcode_macro SET_MACRO_TRAVEL_SETTINGS]
gcode = 
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float %}
	{% set accel = printer["gcode_macro RatOS"].macro_travel_accel %}
	SET_VELOCITY_LIMIT ACCEL={accel} MINIMUM_CRUISE_RATIO=0.5 VELOCITY={speed} SQUARE_CORNER_VELOCITY={5}
	DEBUG_ECHO PREFIX="SET_MACRO_TRAVEL_SETTINGS" MSG="Macro travel settings set. {accel} accel, {speed} velocity"

[gcode_macro SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% if printer["dual_carriage"] is not defined %}
	
	SET_KINEMATIC_POSITION X={printable_x_max / 2} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	{% else %}
	
	IDEX_SET_CENTER_KINEMATIC_POSITION
	{% endif %}

[gcode_macro IDEX_SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x - (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x + (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY

[gcode_macro VERIFY_HYBRID_INVERTED]
gcode = 
	
	{% set inverted = False %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy is defined and printer.fastconfig.settings.ratos_hybrid_corexy.inverted is defined %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy.inverted|lower == 'true' %}
	{% set inverted = True %}
	{% endif %}
	{% endif %}
	{% if inverted == False %}
	{ action_emergency_stop("ratos_hybrid_corexy NOT INVERTED! Inverted hybrid core-xy bugfix not detected.") }
	{% endif %}

[gcode_macro RATOS_ECHO]
gcode = 
	{% set prefix = "RatOS" %}
	{% set debug = params.DEBUG|default(0)|int %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " | " ~ params.PREFIX %}
	{% endif %}
	{% set prefix = prefix ~ ":" %}
	{% set msg = "" %}
	{% if params.MSG is defined %}
	{% set msg = params.MSG %}
	{% else %}
	{% set msg = "No msg parameter provided (this is a bug or unintended use)." %}
	{% endif %}
	{% if not debug %}
	
	M117 {prefix} {msg}
	{% endif %}
	RATOS_LOG PREFIX="{prefix}" MSG="{msg}"
	{% if not debug %}
	RESPOND PREFIX="{prefix}" MSG="{msg}"
	{% else %}
	CONSOLE_ECHO TITLE="{prefix}" TYPE="debug" MSG="{msg}"
	{% endif %}

[gcode_macro ENABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=True
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=prefix_filter VALUE="'{params.FILTER|default('')|lower}'"
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging enabled."

[gcode_macro DISABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=False
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging disabled."

[gcode_macro DEBUG_ECHO]
variable_enabled = False
variable_prefix_filter = ''
gcode = 
	{% set prefix = "DEBUG" %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " - " ~ params.PREFIX %}
	{% endif %}
	{% if enabled and (prefix_filter|lower == '' or prefix_filter|lower in params.PREFIX|lower) %}
	RATOS_ECHO PREFIX="{prefix}" MSG="{params.MSG}" DEBUG=1
	{% endif %}

[gcode_macro START_FEATURE]
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="Start {params.FEATURE} feature gcode"
	{% set scv = printer.toolhead.square_corner_velocity|int|default(5) %}
	{% set accel = printer.toolhead.max_accel|int|default(10000) %}
	{% set ratio = printer.toolhead.minimum_cruise_ratio|float|default(0.5) %}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="scv" VALUE={scv}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="accel" VALUE={accel}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="ratio" VALUE={ratio}
	_USER_START_FEATURE FEATURE="{params.FEATURE}"

[gcode_macro END_FEATURE]
variable_scv = 5
variable_accel = 10000
variable_ratio = 0.5
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="End {params.FEATURE} feature gcode"
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={scv} ACCEL={accel} MINIMUM_CRUISE_RATIO={ratio}
	_USER_END_FEATURE FEATURE="{params.FEATURE}" SCV={scv} ACCEL={accel} RATIO={ratio}

[gcode_macro _ON_LAYER_CHANGE]
variable_layer_number = 0
description = INTERNAL USE ONLY. Call it from the slicers after layer change custom gcode
gcode = 
	
	{% set layer = params.LAYER|int %}
	
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE={layer}
	SET_PRINT_STATS_INFO CURRENT_LAYER={layer}

[gcode_macro _LEARN_MORE_CALIBRATION]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/calibration" %}
	{% set link_text = "RatOS Calibration Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_CHAMBER_FILTER]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter Control" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_FILAMENT]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/filaments" %}
	{% set link_text = "RatOS Filament Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _CONSOLE_SAVE_CONFIG]
gcode = 
	M118 Click <a class="command text--blue">SAVE_CONFIG</a> to save the settings to your printer.cfg.

[gcode_macro _LOAD_RATOS_SKEW_PROFILE]
gcode = 
	{% set ratos_skew_profile = printer["gcode_macro RatOS"].skew_profile|default("") %}
	{% if ratos_skew_profile != "" %}
	{% if printer.fastconfig.config["skew_correction %s" % ratos_skew_profile] is defined %}
	SKEW_PROFILE LOAD={ratos_skew_profile}
	GET_CURRENT_SKEW
	{% else %}
	{% set line_1 = '"Could not find skew profile %s!_N_Clearing skew correction."' % ratos_skew_profile %}
	CONSOLE_ECHO TITLE="Missing skew profile!" TYPE="warning" MSG={line_1}
	SET_SKEW CLEAR=1
	{% endif %}
	{% endif %}

[gcode_macro M601]
gcode = 
	PAUSE

[gcode_macro _STOP_AND_RAISE_ERROR]
gcode = 
	M84
	_RAISE_ERROR MSG="{params.MSG}"

[gcode_macro _RESET_GCODE_VARIABLES]
description = Reset specified [gcode_macro ...] variables to their original values from configuration when Klipper started.
	- MACRO: Name of the GCODE macro containing the variables to reset.
	- VARIABLES: Comma-separated list of variable names to reset (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- QUIET: (optional) If true, suppresses console echo messages for each reset variable. Default is false.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set quiet = params.QUIET|default("false")|lower in ("true", "1", "yes") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	{% set settings = printer.fastconfig.settings[obj_name|lower] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro %s]" % macro) }
	{% endif %}
	
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if settings["variable_%s" % var] is not defined %}
	{ action_raise_error("Variable '%s' is not defined in settings for [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	
	{% for var in vars %}
	{% set var_value = obj[var] %}
	{% if var_value is defined %}
	{% set v = settings["variable_%s" % var] %}
	{% if v != var_value|string %}
	{% if var_value is string %}
	{% set v = '"\'' ~ v|replace('"', '\\"')|replace("'", "\\'") ~ '\'"' %}
	{% endif %}
	SET_GCODE_VARIABLE MACRO={macro} VARIABLE={var} VALUE={v}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Reset {macro} variable {var} to original value: {v} (was {obj[var]})"
	{% endif %}
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro _SHOW_GCODE_VARIABLES]
description = Show current values of specified [gcode_macro ...] variables.
	- MACRO: Name of the GCODE macro containing the variables to show.
	- VARIABLES: Comma-separated list of variable names to show (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- PAD: (optional) If defined, provide a single character to use for padding variable names to align values in a tabular format in the console output. Default is no padding.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set pad = params.PAD|default("") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	
	{% set ns = namespace() %}
	{% set ns.max_len = 0 %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% set ns.max_len = (ns.max_len, var|length)|max %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if pad %}
	{% set padding = pad * (ns.max_len - var|length) %}
	CONSOLE_ECHO MSG="{var}{padding} {obj[var]}"
	{% else %}
	CONSOLE_ECHO MSG="{var}: {obj[var]}"
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro PAUSE]
description = Pauses the print
rename_existing = PAUSE_BASE
variable_extrude = 1.5
variable_retract = 1.5
variable_fan_speed = 0
variable_idex_mode = ""
variable_idex_toolhead = 0
variable_idex_toolhead_x = 0.0
variable_idex_toolhead_y = 0.0
variable_idex_toolhead_z = 0.0
gcode = 
	RATOS_ECHO MSG="Pausing print..."
	
	
	{% set runout_detected = true if params.RUNOUT|default(false)|lower == 'true' else false %}
	
	
	_LED_PAUSE
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	SAVE_GCODE_STATE NAME=PAUSE_state
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_mode VALUE='"{idex_mode}"'
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={idex_toolhead}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_x VALUE={printer.gcode_move.gcode_position.x|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_y VALUE={printer.gcode_move.gcode_position.y|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_z VALUE={printer.gcode_move.gcode_position.z|float}
	DEBUG_ECHO PREFIX="PAUSE" MSG="idex_mode: {idex_mode}, idex_toolhead: {idex_toolhead}, idex_toolhead_x: {idex_toolhead_x}, idex_toolhead_y: {idex_toolhead_y}, idex_toolhead_z: {idex_toolhead_z}"
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="pause"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if current_z < (max_z - 20.0) %}
	{% set z_safe = 20.0 %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	PAUSE_BASE
	
	
	{% if printer["dual_carriage"] is not defined %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan"].speed|float}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	{% if idex_toolhead == 0 %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t1"].speed|float}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106 S0
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set R = printer["gcode_macro PAUSE"].retract|float %}
	{% if can_extrude %}
	G91
	G1 E-{R} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	{% set pause_print_park_x = printer["gcode_macro RatOS"].pause_print_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].pause_print_park_in %}
	{% if runout_detected %}
	{% set pause_print_park_x = printer["gcode_macro RatOS"].runout_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].runout_park_in %}
	{% endif %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	DEBUG_ECHO PREFIX="PAUSE" MSG="z_speed: {z_speed}, pause_print_park_x: {pause_print_park_x}, pause_print_park_in: {pause_print_park_in}, default_toolhead: {default_toolhead}"
	{% if "xyz" in printer.toolhead.homed_axes %}
	G91
	G1 Z{z_safe} F{z_speed}
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% else %}
	
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	_IDEX_SINGLE X={parking_position}
	{% else %}
	PARK_TOOLHEAD
	{% endif %}
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="pause"
	
	RATOS_ECHO MSG="Print paused"

[gcode_macro RESUME]
description = Resumes the print if the printer is paused.
rename_existing = RESUME_BASE
gcode = 
	
	
	RATOS_ECHO MSG="Resuming print..."
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	
	{% set target_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set target_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if target_idex_mode != '' %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set fan_speed = printer["gcode_macro PAUSE"].fan_speed|float %}
	{% if printer["dual_carriage"] is not defined %}
	M106 S{(fan_speed * 255)}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% else %}
	{% if params.TOOLHEAD is defined %}
	
	{% if params.TOOLHEAD == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% else %}
	{% if printer["gcode_macro PAUSE"].idex_toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	{% if params.TOOLHEAD is defined %}
	_SELECT_TOOL T={params.TOOLHEAD} X=-1 Y=-1 TOOLSHIFT=false
	{% else %}
	_SELECT_TOOL T={printer["gcode_macro PAUSE"].idex_toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	{% endif %}
	
	{% set x = printer["gcode_macro PAUSE"].idex_toolhead_x|float %}
	{% set y = printer["gcode_macro PAUSE"].idex_toolhead_y|float %}
	{% set z = printer["gcode_macro PAUSE"].idex_toolhead_z|float %}
	G1 X{x} Y{y} Z{z} F{speed}
	{% if params.TOOLHEAD is defined %}
	
	SAVE_GCODE_STATE NAME=PAUSE_STATE
	{% endif %}
	{% endif %}
	
	
	{% if params.TOOLHEAD is not defined %}
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% if can_extrude %}
	G91
	G1 E{E} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1 MOVE_SPEED={speed}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	RESUME_BASE
	
	
	_LED_PRINTING
	
	RATOS_ECHO MSG="Print resumed"

[gcode_macro CANCEL_PRINT]
description = Cancels the print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	RATOS_ECHO MSG="Cancelling print..."
	END_PRINT
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	
	CANCEL_PRINT_BASE
	RATOS_ECHO MSG="Print cancelled"

[gcode_macro START_PRINT]
description = Start print procedure, use this in your Slicer.
variable_post_processor_version = 2
variable_is_printing_gcode = False
variable_both_toolheads = True
variable_object_xoffset = 0
variable_first_x = -1
variable_first_y = -1
variable_total_toolshifts = 0
variable_initial_tool = 0
variable_extruder_first_layer_temp = ""
variable_extruder_other_layer_temp = ""
gcode = 
	
	{% if params.EXTRUDER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_TEMP parameter not found.")}
	{% endif %}
	{% if params.EXTRUDER_OTHER_LAYER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_OTHER_LAYER_TEMP parameter not found.")}
	{% endif %}
	{% if params.BED_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. BED_TEMP parameter not found.")}
	{% endif %}
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' and printer["gcode_macro RatOS"].danger_force_allow_auto_center_subject|default(false)|lower != 'true'%}
	
	
	
	
	
	{ action_raise_error("The experimental auto_center_subject feature is not supported in this version of RatOS. Please disable it in the RatOS macro settings.") }
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes and printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% if printer["gcode_macro _VAOC"].is_started|default(true)|lower == 'true' %}
	_VAOC_END
	{% endif %}
	{% endif %}
	
	
	_LED_START_PRINTING
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_USER_START_PRINT { rawparams }
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_probe_stowable = printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% endif %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	{% set X0 = params.X0|default(-1)|float %}
	{% set X1 = params.X1|default(-1)|float %}
	{% set Y0 = params.Y0|default(-1)|float %}
	{% set Y1 = params.Y1|default(-1)|float %}
	{% if first_x == -1 or first_y == -1 %}
	{% set first_x = params.FIRST_X|default(-1)|float %}
	{% set first_y = params.FIRST_Y|default(-1)|float %}
	{% endif %}
	{% set total_toolshifts = params.TOTAL_TOOLSHIFTS|default(0)|int %}
	{% set initial_tool = params.INITIAL_TOOL|default(default_toolhead)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	
	
	
	
	
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(printer.heater_bed.target, true)|float %}
	
	
	{% set total_layer_count = params.TOTAL_LAYER_COUNT|default(0)|int %}
	{% set extruder_first_layer_temp = (params.EXTRUDER_TEMP|default("")).split(",") %}
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL BEACON_CONTACT_START_PRINT_TRUE_ZERO={beacon_contact_start_print_true_zero} BEACON_CONTACT_CALIBRATE_MODEL_ON_TRUE_ZERO={beacon_contact_calibrate_model_on_true_zero}
	{% endif %}
	
	_START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH BED_TEMP={bed_temp}
	
	
	RATOS_ECHO MSG="First print coordinates X:{first_x} Y:{first_y}"
	
	
	{% if params.TOTAL_LAYER_COUNT is not defined %}
	{% set link_url = "https://os.ratrig.com/docs/slicers" %}
	{% set link_text = "RatOS Slicer Configuration" %}
	{% set line_1 = '"Your slicer gcode settings are not up to date._N_Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="Incomplete Slicer Configuration detected" TYPE="warning" MSG={line_1}
	{% endif %}
	
	
	SET_PRINT_STATS_INFO CURRENT_LAYER=1
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE=1
	{% if total_layer_count > 0 %}
	SET_PRINT_STATS_INFO TOTAL_LAYER={total_layer_count}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads %}
	{% set initial_tool = 0 if initial_tool == 1 else 1 %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	{% endif %}
	
	
	{% set both_toolheads = true %}
	{% if total_toolshifts == 0 %}
	{% set both_toolheads = false %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	{% endif %}
	{% if both_toolheads and (idex_mode == "copy" or idex_mode == "mirror") %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Gcode tool changes found. Copy and mirror mode do not support toolchanges.")}
	{% endif %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set both_toolheads = true %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=initial_tool VALUE={initial_tool}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_x VALUE={first_x}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_y VALUE={first_y}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=total_toolshifts VALUE={total_toolshifts}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=both_toolheads VALUE={both_toolheads}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_first_layer_temp VALUE="'{params.EXTRUDER_TEMP}'"
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_other_layer_temp VALUE="'{params.EXTRUDER_OTHER_LAYER_TEMP}'"
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE=0
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set svv = printer.save_variables.variables %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set stepper_x_position_min = printer.fastconfig.settings.stepper_x.position_min|float %}
	{% set stepper_x_position_endstop = printer.fastconfig.settings.stepper_x.position_endstop|float %}
	{% set dual_carriage_position_max = printer.fastconfig.settings.dual_carriage.position_max|float %}
	{% set dual_carriage_position_endstop = printer.fastconfig.settings.dual_carriage.position_endstop|float %}
	{% set x_parking_space = parking_position_t0 - (stepper_x_position_endstop , stepper_x_position_min)|max %}
	{% set dc_parking_space = (dual_carriage_position_endstop , dual_carriage_position_max)|min - parking_position_t1 %}
	{% if svv.idex_xoffset|abs >= (x_parking_space - 0.5) or svv.idex_xoffset|abs >= (dc_parking_space - 0.5) %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Toolhead x-offset is too high for the available parking space. Calibrate your X and DC endstop positions and make sure you stay below 1mm." % (copy_mode_max_width)) }
	{% endif %}
	{% endif %}
	
	
	{% if (idex_mode == "copy" or idex_mode == "mirror") and printer.fastconfig.settings.ratos.enable_gcode_transform %}
	
	{% if params.MIN_X is not defined or params.MAX_X is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Something went wrong! Missing important post processor start print parameter!") }
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE=0
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	
	{% set boundary_box_min_x = params.MIN_X|default(0)|float %}
	{% set boundary_box_max_x = params.MAX_X|default(printable_x_max)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if default_toolhead == 0 %}
	
	{% set boundary_box_max_x = boundary_box_max_x + svv.idex_xoffset %}
	{% else %}
	
	{% set boundary_box_min_x = boundary_box_min_x - svv.idex_xoffset %}
	{% endif %}
	
	{% set center_x = printable_x_max / 2.0 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set object_width = boundary_box_max_x - boundary_box_min_x %}
	{% set copy_mode_max_width = center_x %}
	{% set mirror_mode_max_width = center_x - safe_distance / 2.0 %}
	
	DEBUG_ECHO PREFIX="START_PRINT" MSG="OBJECT_WIDTH: {object_width} BOUNDARY_BOX_MIN_X: {boundary_box_min_x} BOUNDARY_BOX_MAX_X: {boundary_box_max_x} CENTER_X: {center_x} SAFE_DISTANCE: {safe_distance}"
	
	
	{% if idex_mode == "copy" and object_width > copy_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for copy mode! Max supported width is %s mm" % (copy_mode_max_width)) }
	{% endif %}
	{% if idex_mode == "mirror" and object_width > mirror_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for mirror mode! Max supported width is %s mm" % (mirror_mode_max_width)) }
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = (printable_x_max - boundary_box_max_x - boundary_box_min_x) / 2 %}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE={object_xoffset}
	{% endif %}
	
	{% endif %}
	
	
	{% set has_initial_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_toolhead_filament_sensor %}
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% set has_initial_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_bowden_filament_sensor %}
	
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% if printer["dual_carriage"] is defined and both_toolheads %}
	
	{% set has_secondary_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set has_secondary_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_CHAMBER_FILTER_ON AT="before_print_start"
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true' %}
	{% if both_toolheads %}
	RATOS_ECHO MSG="Spool join is not possible if both toolheads are in use!"
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	{% endif %}
	
	
	CLEAR_PAUSE
	{% if printer["gcode_macro RatOS"].force_absolute_position|lower == 'true' %}
	G90
	{% endif %}
	SAVE_GCODE_STATE NAME=start_print_state
	
	
	G21
	
	G90
	
	M82
	_USER_START_PRINT_BEFORE_HOMING { rawparams }
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_BEGIN_BATCH
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_Z_HOP
	
	
	{% if idex_mode != '' and not (printer.fastconfig.settings.beacon is defined and (beacon_contact_start_print_true_zero or beacon_adaptive_heat_soak)) %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	{% if chamber_temp > 0 %}
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED={printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float}
	{% endif %}
	{% endif %}
	_CHAMBER_HEATER_ON START_CHAMBER_TEMP={start_chamber_temp} CHAMBER_TEMP={chamber_temp}
	_USER_START_PRINT_HEAT_CHAMBER { rawparams } CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_START_PRINT_BEFORE_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	RATOS_ECHO MSG="Heating bed..."
	
	M190 S{bed_temp}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_adaptive_heat_soak %}
	_MOVE_TO_SAFE_Z_HOME
	
	G1 Z2.5 F{z_speed}
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK LAYER_QUALITY={beacon_adaptive_heat_soak_layer_quality} MAXIMUM_FIRST_LAYER_DURATION={beacon_adaptive_heat_soak_maximum_first_layer_duration} MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={beacon_adaptive_heat_soak_max_wait}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_BED { rawparams }
	
	
	_START_PRINT_AFTER_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	_USER_START_PRINT_BED_MESH { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_BED_MESH X0={X0} X1={X1} Y0={Y0} Y1={Y1} T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_END_BATCH
	{% endif %}
	
	
	{% if idex_mode == '' %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[initial_tool]|float}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[0]|float}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={extruder_first_layer_temp[1]|float}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_PARK { rawparams }
	
	
	_START_PRINT_PARK
	
	
	RATOS_ECHO MSG="Heating Extruder..."
	{% if idex_mode == '' %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[initial_tool]|float}  MAXIMUM={extruder_first_layer_temp[initial_tool]|float + 5}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[0]|float}  MAXIMUM={extruder_first_layer_temp[0]|float + 5}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder1" MINIMUM={extruder_first_layer_temp[1]|float}  MAXIMUM={extruder_first_layer_temp[1]|float + 5}
	{% endif %}
	{% endif %}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	{% if idex_mode == '' %}
	_LED_PRINTING
	{% else %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	_LED_PRINTING
	{% else %}
	{% if both_toolheads %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	{% if toolchange_standby_temp > -1 %}
	_LED_TOOLHEAD_STANDBY TOOLHEAD={0 if initial_tool == 1 else 1}
	{% else %}
	_LED_PRINTING TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% else %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_EXTRUDER { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_AFTER_HEATING_EXTRUDER X0={X0} X1={X1} Y0={Y0} Y1={Y1} INITIAL_TOOLHEAD={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if idex_mode != '' %}
	{% if not both_toolheads %}
	{% if initial_tool != default_toolhead %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if idex_mode != '' %}
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=standby VALUE=False
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=standby VALUE=False
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if initial_tool == 1 else 'extruder1'} TARGET={toolchange_standby_temp}
	SET_GCODE_VARIABLE MACRO=T{0 if initial_tool == 1 else 1} VARIABLE=standby VALUE=True
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=start_print_state
	
	{% if printer["dual_carriage"] is defined %}
	_SET_IDEX_MODE_OFFSET
	{% endif %}
	
	
	{% if idex_mode != '' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% if idex_mode == "copy" and idex_mode != act_idex_mode %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == "mirror" and idex_mode != act_idex_mode %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={object_xoffset} MOVE=0
	{% endif %}
	{% else %}
	_SELECT_TOOL T={initial_tool} TOOLSHIFT=false
	_SET_TOOLHEAD_OFFSET
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	_SET_EXTRUSION_MODE
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={printer["print_stats"].print_duration}
	{% endif %}
	
	
	_USER_END_START_PRINT { rawparams }
	
	G92 E0
	
	
	_CHAMBER_FILTER_ON AT="after_print_start"
	
	_ALERT_NON_ZERO_Z_OFFSET
	
	RATOS_ECHO MSG="Printing..."

[gcode_macro _START_PRINT_BEFORE_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set is_stowable_probe = true if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' else false %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Pre-heating extruder..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={min_temp}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET={min_temp}
	{% endif %}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	{% endif %}
	{% endif %}
	
	
	{% if not is_stowable_probe %}
	{% if printer["dual_carriage"] is defined and act_t != default_toolhead %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	{% endif %}
	RATOS_ECHO MSG="Heat soaking z probe..."
	_MOVE_TO_SAFE_Z_HOME
	
	G0 Z2 F{z_speed}
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Waiting for extruder to be preheated..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	{% if default_toolhead == 0 %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_Z_HOP
	{% endif %}
	
	
	{% if auto_z_offset_calibration %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	PARK_TOOLHEAD
	_CLEANING_MOVE TOOLHEAD={default_toolhead} AUTOMATED=True
	_SELECT_TOOL T={0 if default_toolhead == 1 else 1} X={parking_position_t0 if default_toolhead == 1 else parking_position_t1} Y=0 TOOLSHIFT=false
	_CLEANING_MOVE TOOLHEAD={0 if default_toolhead == 1 else 1} AUTOMATED=True
	_VAOC_CALIBRATE_Z_OFFSET AUTO_Z_OFFSET=True
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=false
	{% endif %}
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	{% if needs_rehoming %}
	G28 Z
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	_START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE
	{% endif %}
	{% endif %}
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	PROBE PROBE_METHOD=contact SAMPLES=1

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	{% set fuzzy_radius = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_radius|default(0)|float if beacon_contact_start_print_true_zero_fuzzy_position else 0 %}
	
	{% set contact_true_zero_temp_has_been_set = False %}
	
	
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	
	
	
	{% if printer.beacon.last_probe_result|lower == "ok" %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	RATOS_ECHO MSG="Auto calibration nozzle wipe with probe result {last_z_offset}..."
	G0 Z{(0.2 + last_z_offset)} F{z_speed}
	G0 X70 F300
	{% else %}
	RATOS_ECHO MSG="Skipping auto calibration nozzle wipe because probing failed!"
	{% endif %}
	{% elif beacon_contact_wipe_before_true_zero_method == "probe_clean" %}
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	
	{% set contact_true_zero_temp_has_been_set = True %}
	
	
	
	
	
	
	
	
	BEACON_PROBE_CLEAN X=50 Y=10
	{% else %}
	CONSOLE_ECHO TYPE="error" TITLE="Unknown wipe method" MSG="Unknown wipe method '{beacon_contact_wipe_before_true_zero_method}' configured, skipping wipe before beacon true zero."
	{% endif %}
	{% endif %}
	
	
	G0 Z5 F{z_speed}
	_MOVE_TO_SAFE_Z_HOME FUZZY_RADIUS={fuzzy_radius}
	
	
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION
	
	{% if not contact_true_zero_temp_has_been_set %}
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon contact auto calibration..."
	
	{% if beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	
	G0 Z5 F{z_speed}

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION]
gcode = 
	{% set pos = printer.ratos.last_move_to_safe_z_home_position %}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE={pos[0]}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE={pos[1]}

[gcode_macro _START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set first_x = printer["gcode_macro START_PRINT"].first_x|default(-1)|float %}
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2.0 %}
	{% set center_y = printable_y_max / 2.0 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% if printer["dual_carriage"] is defined %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% endif %}
	
	
	{% set X0 = params.X0|default(-1)|int %}
	{% set X1 = params.X1|default(-1)|int %}
	{% set Y0 = params.Y0|default(-1)|int %}
	{% set Y1 = params.Y1|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	
	{% if idex_mode == '' %}
	
	_PRIME
	{% else %}
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	RATOS_ECHO PREFIX="IDEX" MSG="using combined prime offset for IDEX {idex_mode} mode"
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	{% if both_toolheads %}
	{% if initial_toolhead == 0 %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T{initial_toolhead}"
	_SELECT_TOOL T={initial_toolhead} TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	SET_MACRO_TRAVEL_SETTINGS
	
	{% if (X0 > -1 and Y1 > -1) or (first_x > 0 and first_y > 0) %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	{% endif %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	{% set first_z = 1 %}
	{% else %}
	{% set first_z = 3 %}
	{% endif %}
	
	
	{% if idex_mode == "mirror" %}
	{% if first_y >= 0 %}
	G0 Y{first_y} F{speed}
	{% else %}
	G0 Y{Y1} F{speed}
	{% endif %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={initial_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={initial_toolhead} E={printer["gcode_macro RatOS"].toolchange_first_purge|default(50)|float}
	_CLEANING_MOVE TOOLHEAD={initial_toolhead} AUTOMATED=True
	{% endif %}
	{% if first_x >= 0 and first_y >= 0 %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% else %}
	{% set first_x = X0 %}
	{% set first_y = Y0 %}
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'min' %}
	{% set first_x = X0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'max' %}
	{% set first_x = X1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|float <= center_x %}
	{% set first_x = X0 %}
	{% else %}
	{% set first_x = X1 %}
	{% endif %}
	{% endif %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'min' %}
	{% set first_y = Y0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'max' %}
	{% set first_y = Y1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|float <= center_y %}
	{% set first_y = Y0 %}
	{% else %}
	{% set first_y = Y1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	
	
	_LOAD_RATOS_SKEW_PROFILE

[gcode_macro _PRIME]
gcode = 
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	PRIME_BLOB INITIAL_TOOLHEAD={params.INITIAL_TOOLHEAD} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={params.IDEX_MODE} Y1={params.Y1}
	{% else %}
	
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif params.IDEX_MODE == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro END_PRINT]
description = End print procedure, use this in your Slicer.
gcode = 
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SAVE_GCODE_STATE NAME=end_print_state
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = printer["gcode_macro START_PRINT"].object_xoffset|default(0)|float %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(0-object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={(0-object_xoffset)}
	{% endif %}
	{% endif %}
	
	
	_USER_END_PRINT_BEFORE_HEATERS_OFF { rawparams }
	_END_PRINT_BEFORE_HEATERS_OFF
	TURN_OFF_HEATERS
	_USER_END_PRINT_AFTER_HEATERS_OFF { rawparams }
	_END_PRINT_AFTER_HEATERS_OFF
	_USER_END_PRINT_PARK { rawparams }
	_END_PRINT_PARK
	
	
	{% if printer["gcode_macro RatOS"].skew_profile is defined %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined and printer["gcode_macro RatOS"].end_print_motors_off|lower != 'false' %}
	
	M84
	{% endif %}
	
	
	M107
	
	
	BED_MESH_CLEAR
	RATOS_ECHO MSG="Done :)"
	
	
	RESTORE_GCODE_STATE NAME=end_print_state
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	M84
	{% endif %}
	
	
	RESET_NAMED_OFFSET EVENT="end_print"
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_CHAMBER_FILTER_ON AT="print_end"
	_CHAMBER_FILTER_OFF
	
	
	_CHAMBER_HEATER_OFF
	
	_USER_END_PRINT_FINISHED { rawparams }

[gcode_macro _END_PRINT_BEFORE_HEATERS_OFF]
gcode = 
	RATOS_ECHO MSG="Cleaning up..."

[gcode_macro _END_PRINT_AFTER_HEATERS_OFF]
gcode = 
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% set z_hop = printer["gcode_macro RatOS"].end_print_park_z_hop|float %}
	{% set r = printer["gcode_macro RatOS"].end_print_retract_filament|default(4)|float %}
	{% if current_z < (max_z - z_hop) %}
	{% set z_safe = z_hop %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G91
	
	{% if can_extrude %}
	G1 E-2 F3600
	{% endif %}
	
	G0 Z{z_safe} F3600
	
	{% if can_extrude %}
	G1 E-{(r-2)} F3600
	{% endif %}
	
	G90

[gcode_macro _SET_EXTRUSION_MODE]
gcode = 
	
	{% if printer["gcode_macro RatOS"].relative_extrusion|lower == 'true' %}
	M83
	{% else %}
	M82
	{% endif %}

[gcode_macro GENERATE_SHAPER_GRAPHS]
description = Genarates input shaper resonances graphs for analysis. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	{% set hz_per_sec = params.HZ_PER_SEC|default(1)|float %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set copy_mode_offset = printable_x_max / 4.0 %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	_IDEX_SINGLE
	{% endif %}
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	
	
	{% if idex_mode != 'copy' and idex_mode != 'mirror' %}
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	{% endif %}
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Shaper graph"

[gcode_shell_command generate_shaper_graph_x]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-x.sh
timeout = 60.
verbose = True

[gcode_shell_command generate_shaper_graph_y]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-y.sh
timeout = 60.
verbose = True

[gcode_macro MEASURE_COREXY_BELT_TENSION]
description = Generates resonance graph used to ensure belts are equally tensioned. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	_IDEX_SINGLE
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if measure_t1 == false or measure_t0 == false %}
	{action_raise_error("Axis specified. Not supported for belt tension on Y.")}
	{% else %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	G4 P5000
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	PARK_TOOLHEAD
	{% endif %}
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	G1 X{parking_position_t1} F{speed}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	
	
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Belt Tension Graph"

[gcode_shell_command generate_belt_tension_graph]
command = /home/pi/printer_data/config/RatOS/scripts/generate-belt-tension-graph.sh
timeout = 90.
verbose = True

[idle_timeout]
gcode = 
	{% if printer.webhooks.state|lower == 'ready' %}
	{% if printer.pause_resume.is_paused|lower == 'false' %}
	_USER_BEFORE_IDLE_TIMEOUT
	RATOS_ECHO PREFIX="IDLE" MSG="2 hours since last activity. Powering off heaters and motors.."
	TURN_OFF_HEATERS
	M84
	_USER_AFTER_IDLE_TIMEOUT
	{% endif %}
	{% endif %}
timeout = 7200

[temperature_sensor raspberry_pi]
sensor_type = temperature_host

[skew_correction]

[named_offsets]

[input_shaper]

[virtual_sdcard]
path = ~/printer_data/gcodes

[display_status]

[pause_resume]

[force_move]
enable_force_move = True

[respond]

[resonance_generator]

[ratos]
allow_unknown_gcode_generator = True
enable_gcode_transform = True

[exclude_object]

[bed_mesh]
split_delta_z = 0.001
horizontal_move_z = 2
mesh_min = 20,20
mesh_max = 480,480
probe_count = 40,40
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = .2
speed = 600
log_points = False

[fastconfig]

[heater_bed]
heater_pin = heater_bed_heating_pin
sensor_pin = heater_bed_sensor_pin
sensor_type = Generic 3950
min_temp = 0
max_temp = 140
pwm_cycle_time = 0.103
control = pid
pid_kp = 61.987
pid_ki = 1.781
pid_kd = 539.289

[printer]
kinematics = ratos_hybrid_corexy
max_velocity = 800
max_accel = 10000
minimum_cruise_ratio = 0.5
max_z_velocity = 50
max_z_accel = 600
square_corner_velocity = 5

[ratos_hybrid_corexy]
inverted = true

[dual_carriage]
axis = x
safe_distance = 55
position_max = 559.6
position_endstop = 559.6
position_min = 0
step_pin = PF9
dir_pin = dual_carriage_dir_pin
enable_pin = !PG2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t1:PA2

[gcode_macro _SET_IDEX_MODE_OFFSET]
description = "Internal use only. Sets the 'idex_mode' named offset that the active idex mode requires."
gcode = 
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_SET_IDEX_MODE_OFFSET" MSG="idex_mode: {idex_mode}, center_x: {center_x}"
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	SET_NAMED_OFFSET NAME=idex_mode X={(-center_x / 2)}
	{% else %}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% else %}
	{action_raise_error("_SET_IDEX_MODE_OFFSET: Printer not homed")}
	{% endif %}

[gcode_macro IDEX_SINGLE]
gcode = 
	_IDEX_REMAP_TOOLHEADS ENABLE=False
	_IDEX_SINGLE

[gcode_macro _IDEX_SINGLE]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_single"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set init = params.INIT|default(0)|int %}
	{% set new_x = params.X|default(-1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_default_t = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="init: {init}, new_x: {new_x}, idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, act_t: {act_t}"
	
	{% if idex_mode == "copy" or idex_mode == "mirror" or init == 1 %}
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="reset idex_mode offset"
	G1 X{center_x} F{(speed)}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="activate default carriage"
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolheads"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	G90
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position."
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1}
	G1 X{parking_position_default_t} F{speed}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move default toolhead to its new position."
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% if new_x == -1 %}
	{% set new_x = center_x %}
	{% endif %}
	G1 X{new_x} F{speed}
	
	M400
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="X Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set extruder motion queue."
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if default_toolhead==0 else default_toolhead}
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolhead offset."
	_SET_TOOLHEAD_OFFSET
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set input shaper."
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[default_toolhead]|float)} SHAPER_FREQ_Y={(shaper_y_freq[default_toolhead]|float)} SHAPER_TYPE_X={(shaper_x_type[default_toolhead]|lower)} SHAPER_TYPE_Y={(shaper_y_type[default_toolhead]|lower)}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="update Frontend."
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if default_toolhead==0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if default_toolhead==1 else False}
	{% else %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_single"

[gcode_macro IDEX_COPY]
gcode = 
	_IDEX_COPY

[gcode_macro _IDEX_COPY]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_copy"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set y = params.Y|default(-1)|int %}
	{% set dance = params.DANCE|default(1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_COPY" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}, y: {y}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "copy" %}
	{% if idex_mode == "mirror" %}
	{% if y>=0 %}
	G1 X{center_x} Y{y} F{(speed)}
	{% else %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	
	
	{% if idex_mode != "mirror" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance == 1 %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[2]|float)} SHAPER_FREQ_Y={(shaper_y_freq[2]|float)} SHAPER_TYPE_X={(shaper_x_type[2]|lower)} SHAPER_TYPE_Y={(shaper_y_type[2]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_copy"

[gcode_macro IDEX_MIRROR]
gcode = 
	_IDEX_MIRROR

[gcode_macro _IDEX_MIRROR]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_mirror"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set dance = params.DANCE|default(1)|int %}
	{% set priming = params.PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_MIRROR" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "mirror" %}
	
	{% if idex_mode == "copy" %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS MIRROR_PRIMING={params.PRIMING}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=MIRROR
	
	
	{% if idex_mode != "copy" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance and not priming %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[3]|float)} SHAPER_FREQ_Y={(shaper_y_freq[3]|float)} SHAPER_TYPE_X={(shaper_x_type[3]|lower)} SHAPER_TYPE_Y={(shaper_y_type[3]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_mirror"

[gcode_macro _IDEX_SET_TOOLHEADS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set mirror_priming = params.MIRROR_PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position_inactive_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_IDEX_SET_TOOLHEADS" MSG="idex_mode: {idex_mode}, act_t: {act_t}, center_x: {center_x}, mirror_priming: {mirror_priming}"
	
	
	{% if act_t != default_toolhead %}
	_SET_TOOLHEAD_OFFSET FORCE_TOOLHEAD={default_toolhead} MOVE=1
	{% endif %}
	
	{% if mirror_priming %}
	
	
	
	{% if parking_position_t0|abs < parking_position_t1 - printable_x_max %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{printable_x_max + parking_position_t0|abs} F{(speed)}
	{% else %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{0 - (parking_position_t1 - printable_x_max)} F{(speed)}
	{% endif %}
	
	{% else %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1} MODE=PRIMARY
	G1 X{parking_position_inactive_t} F{(speed)}
	
	
	{% if act_t==1 %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{center_x / 2} F{(speed)}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"

[gcode_macro IDEX_PARK]
gcode = 
	
	PARK_TOOLHEAD

[gcode_macro PARK_TOOLHEAD]
gcode = 
	
	{% set idex_mode = 'none' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="PARK_TOOLHEAD" MSG="Parking T{act_t}.."
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set parking_position_inact_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set printable_y_min = printer["gcode_macro RatOS"].printable_y_min|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" and 'xy' in printer.toolhead.homed_axes %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% elif printer.toolhead.position.y|float < printable_y_min %}
	G1 Y{printable_y_min} F{speed}
	{% endif %}
	
	SAVE_GCODE_STATE NAME=_PARK_TOOLHEAD
	G90
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0.5
	
	
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_inact_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	
	SET_VELOCITY_LIMIT ACCEL={printer.toolhead.max_accel} MINIMUM_CRUISE_RATIO=0.5
	M400
	RESTORE_GCODE_STATE NAME=_PARK_TOOLHEAD
	
	{% endif %}

[gcode_macro JOIN_SPOOLS]
gcode = 
	
	{% set spools = params.SPOOLS|default("") %}
	
	{% if spools == "" %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% else %}
	{% if spools != "0,1" and spools != "1,0" %}
	RATOS_ECHO MSG="Wrong spool configuration!"
	RATOS_ECHO MSG="Join Spools = JOIN_SPOOLS SPOOLS=0,1"
	RATOS_ECHO MSG="Deactivate = JOIN_SPOOLS SPOOLS="
	{% else %}
	{% if spools == "0,1" or spools == "1,0" %}
	_IDEX_JOIN_SPOOLS ENABLE=true
	{% else %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_JOIN_SPOOLS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if enable %}
	{% set has_t0_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t1_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t0_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined else false %}
	{% set has_t1_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined else false %}
	{% if (has_t0_toolhead_filament_sensor and has_t1_toolhead_filament_sensor) or (has_t0_bowden_filament_sensor and has_t1_bowden_filament_sensor) %}
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=True
	RATOS_ECHO MSG="Spool joining enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Can not enable spool joining! No filament sensors found."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining deactivated!"
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining is not possible in copy and mirror mode!"
	{% endif %}

[gcode_macro _JOIN_SPOOL]
gcode = 
	
	{% set old_toolhead = params.TOOLHEAD|int %}
	{% set new_toolhead = 0 if old_toolhead == 1 else 1 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set purge_after_load = printer["gcode_macro T%s" % new_toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_JOIN_SPOOL" MSG="toolhead: {new_toolhead}"
	
	{% set has_filament = true %}
	{% set has_new_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% set has_new_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% if has_new_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	{% if has_new_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	
	{% if has_filament %}
	RATOS_ECHO MSG="Joining spools! Please wait for extruder to heat up...."
	
	
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={new_toolhead}
	
	
	_DEACTIVATE_TOOLHEAD TOOLHEAD={old_toolhead}
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set extruder_temp = extruder_first_layer_temp[new_toolhead]|float %}
	{% else %}
	{% set extruder_temp = extruder_other_layer_temp[new_toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if new_toolhead == 0 else 'extruder1'} TARGET={extruder_temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if new_toolhead == 0 else 'extruder1'} MINIMUM={extruder_temp}  MAXIMUM={extruder_temp + 5}
	
	
	{% if purge_after_load > 0 %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_toolhead == 0 else new_toolhead}
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={new_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={new_toolhead} E={purge_after_load}
	_CLEANING_MOVE TOOLHEAD={new_toolhead} AUTOMATED=True
	
	
	SET_DUAL_CARRIAGE CARRIAGE={old_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if old_toolhead == 0 else old_toolhead}
	
	{% endif %}
	
	
	RESUME TOOLHEAD={new_toolhead}
	
	
	_IDEX_JOIN_SPOOLS ENABLE=false
	
	{% else %}
	{ action_raise_error("Spool join failed! No filament found or filament sensor is disabled.") }
	{% endif %}

[gcode_macro REMAP_TOOLHEADS]
gcode = 
	
	{% set toolheads = params.TOOLHEADS|default("") %}
	
	{% if toolheads == "" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% else %}
	{% if toolheads != "0,1" and toolheads != "1,0" %}
	RATOS_ECHO MSG="Wrong toolhead configuration!"
	RATOS_ECHO MSG="Remap = REMAP_TOOLHEADS TOOLHEADS=0,1"
	RATOS_ECHO MSG="Deactivate = REMAP_TOOLHEADS TOOLHEADS="
	{% else %}
	{% if toolheads == "0,1" or toolheads == "1,0" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=true
	_IDEX_SINGLE
	{% else %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_REMAP_TOOLHEADS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	{% if not enable or (idex_mode != "copy" and idex_mode != "mirror") %}
	{% if enable %}
	RATOS_ECHO MSG="Toolhead remapping enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping deactivated!"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE={enable}
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping not possible in copy and mirror mode!"
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	{% endif %}

[gcode_macro SHAPER_CALIBRATE]
rename_existing = SHAPER_CALIBRATE_ORG
gcode = 
	RATOS_ECHO PREFIX="IDEX" MSG="SHAPER_CALIBRATE is useless on IDEX machines. Please use the GENERATE_SHAPER_GRAPHS macro and type the values into `variable_shaper_*_freq` and `variable_shaper_*_type manually`."

[gcode_shell_command generate_shaper_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-shaper-graph.sh
timeout = 120.
verbose = True

[gcode_shell_command generate_tension_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-belt-tension-graph.sh
timeout = 120.
verbose = True

[gcode_macro SET_PRESSURE_ADVANCE]
variable_snyc_toolheads = False
rename_existing = SET_PRESSURE_ADVANCE_BASE
gcode = 
	{% if params.SYNC_TOOLHEADS is defined %}
	{% set snyc_toolheads = true if params.SYNC_TOOLHEADS|default(false)|lower == 'true' else false %}
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=True
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="Syncing toolheads..."
	{% else %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' or snyc_toolheads %}
	{% set advance = params.ADVANCE|default(printer['extruder'].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['extruder'].smooth_time|float)|float %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T0"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T1"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder1' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% else %}
	{% set extruder = 'extruder' if act_t == 0 else 'extruder1' %}
	{% if params.EXTRUDER is defined %}
	{% set extruder = params.EXTRUDER %}
	{% endif %}
	{% if extruder == 'extruder' or extruder == 'extruder1' %}
	{% set advance = params.ADVANCE|default(printer['%s' % extruder].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['%s' % extruder].smooth_time|float)|float %}
	SET_PRESSURE_ADVANCE_BASE EXTRUDER={extruder} ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% if params.EXTRUDER is not defined %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG={"T%s" % act_t}
	{% endif %}
	{% else %}
	SET_PRESSURE_ADVANCE_BASE { rawparams }
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro M106]
rename_existing = M106.1
variable_swap_speed = -1
gcode = 
	
	{% set s = [[params.S|default(255)|int, 255]|min, 0]|max %}
	{% set p = params.P|default(-1)|int %}
	{% set speed = s / 255 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set t = 1 if idex_mode=='primary' else 0 %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(0)|int == 1 else false %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set sync_fans = true %}
	{% endif %}
	
	
	{% if sync_fans and idex_mode != "copy" and idex_mode != "mirror" %}
	
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int %}
	
	
	{% if toolshift_count > total_toolshifts %}
	{% set sync_fans = false %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE=-1
	
	
	{% if p == -1 %}
	
	{% if speed == 0 %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed}
	{% else %}
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE={speed}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={(speed if (t == 0 or sync_fans) else 0)}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={(speed if (t == 1 or sync_fans) else 0)}
	{% endif %}
	{% else %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed if t == p else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed if t == p else 0}
	{% endif %}
	
	
	M106.1 S{s}

[gcode_macro M107]
rename_existing = M107.1
gcode = 
	{% set p = params.P|default(-1)|int %}
	M106 S0 P{p}

[gcode_macro _SELECT_TOOL]
variable_last_timestamp = 0
gcode = 
	{% if params.T is defined %}
	{% set idex_mode = '' %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if "xyz" not in printer.toolhead.homed_axes and (idex_mode == "copy" or idex_mode == "mirror") %}
	_IDEX_SINGLE
	{% set idex_mode = 'reset' %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set new_t = params.T|int %}
	
	
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads and is_printing_gcode %}
	{% set new_t = 0 if new_t == 1 else 1 %}
	{% endif %}
	
	
	{% set toolchange_prepurging_timer = printer["gcode_macro RatOS"].toolchange_prepurging_timer|default(0)|int %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	DEBUG_ECHO PREFIX="_SELECT_TOOL" MSG="act_t: {act_t}, new_t: {new_t}, is_printing_gcode: {is_printing_gcode}, swap_toolheads: {swap_toolheads}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	{% set act_extruder = 'extruder%s' % ('' if new_t == 0 else new_t) %}
	{% if new_t != act_t or printer.toolhead.extruder != act_extruder or idex_mode == 'reset' %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Selecting T{new_t}.."
	
	
	M220 S100
	
	
	
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(1)|int == 1 else false %}
	
	
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set toolshift = false %}
	{% endif %}
	
	
	{% set fan_speed = printer["fan_generic part_fan_t%s" % act_t].speed %}
	
	
	{% set deactivate_toolhead = false %}
	{% if is_printing_gcode %}
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int + 1 %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE={toolshift_count}
	{% if toolshift_count == total_toolshifts %}
	{% set deactivate_toolhead = true %}
	{% endif %}
	{% endif %}
	
	
	{% set needs_wakeup = true if printer["gcode_macro T%s" % new_t].standby|default(false)|lower == 'true' else false %}
	
	
	{% set needs_purging = false %}
	{% set wake_up_purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% if is_printing_gcode and toolchange_prepurging_timer > 0 and wake_up_purge > 0 %}
	{% set new_timestamp = printer["print_stats"].print_duration %}
	{% set elapsed_time = new_timestamp - last_timestamp %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={new_timestamp}
	{% if elapsed_time > toolchange_prepurging_timer %}
	{% set needs_purging = true %}
	{% endif %}
	{% endif %}
	
	
	{% set first_use_purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% if toolshift_count == 1 and first_use_purge > 0 %}
	{% set needs_purging = true %}
	{% endif %}
	
	
	{% if is_printing_gcode and (toolchange_standby_temp > -1 or needs_purging or needs_wakeup) %}
	_TOOLHEAD_STANDBY TOOLHEAD={act_t}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	_TOOLHEAD_WAKEUP TOOLHEAD={new_t} X={new_x} Y={new_y} Z={new_z} FAN_SPEED={fan_speed} TOOLSHIFT_COUNT={toolshift_count}
	{% else %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(false)|lower == 'true' else false %}
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if (new_t == 0 or sync_fans) else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if (new_t == 1 or sync_fans) else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	_TOOLCHANGE T={new_t} X={new_x} Y={new_y} Z={new_z} PARK_T0={park_t0} PARK_T1={park_t1} TOOLSHIFT={toolshift}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[new_t]|float)} SHAPER_FREQ_Y={(shaper_y_freq[new_t]|float)} SHAPER_TYPE_X={(shaper_x_type[new_t]|lower)} SHAPER_TYPE_Y={(shaper_y_type[new_t]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if new_t == 0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if new_t == 1 else False}
	
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% set sanity_check_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if new_t == 0 %}
	{% if printer.toolhead.extruder == 'extruder' %}
	{% if sanity_check_idex_mode == 'primary' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% elif new_t == 1 %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% if sanity_check_idex_mode == 'inactive' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _TOOLHEAD_STANDBY]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Putting toolhead T{toolhead} into standby mode."
	DEBUG_ECHO PREFIX="_TOOLHEAD_STANDBY" MSG="toolhead: {toolhead}, config_z_hop: {config_z_hop}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={toolhead} SYNC=0
	PARK_TOOLHEAD
	
	
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={toolchange_standby_temp}
	{% endif %}
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=True
	{% endif %}
	
	
	_LED_TOOLHEAD_STANDBY TOOLHEAD={toolhead}

[gcode_macro _TOOLHEAD_WAKEUP]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set fan_speed = params.FAN_SPEED|float %}
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift_count = params.TOOLSHIFT_COUNT|default(0)|int %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% if toolshift_count == 1 %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% endif %}
	{% set needs_wakeup = true if printer["gcode_macro T%s" % toolhead].standby|default(false)|lower == 'true' else false %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Waking up toolhead T{toolhead}. Please wait for extruder to heat up..."
	DEBUG_ECHO PREFIX="_TOOLHEAD_WAKEUP" MSG="toolhead: {toolhead}, fan_speed: {fan_speed}, new_x: {new_x}, new_y: {new_y}, new_z: {new_z}, config_z_hop: {config_z_hop}"
	
	
	_LED_TOOLHEAD_WAKEUP TOOLHEAD={toolhead}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={toolhead} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE=1
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if toolhead == 0 else toolhead}
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if needs_wakeup %}
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set temp = extruder_first_layer_temp[toolhead]|float %}
	{% else %}
	{% set temp = extruder_other_layer_temp[toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if toolhead == 0 else 'extruder1'} MINIMUM={temp}  MAXIMUM={temp + 5}
	{% endif %}
	
	
	_LED_PRINTING TOOLHEAD={toolhead}
	
	
	{% if purge > 0 %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={toolhead} E={purge}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	
	
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if toolhead == 1 else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	G92 E0
	G1 E-{e} F{feedrate}
	G92 E0
	
	
	{% if new_x >= 0 and new_y >= 0 %}
	G1 X{new_x} Y{new_y} F{speed}
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={config_z_hop} T={toolhead} SYNC=0
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=False

[gcode_macro _TOOLCHANGE]
variable_toolshift_count = 0
gcode = 
	
	
	{% set new_t = params.T|default(-1)|int %}
	{% set new_x = params.X|default(-1.0)|float %}
	{% set new_y = params.Y|default(-1.0)|float %}
	{% set new_z = params.Z|default(-1.0)|float %}
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(true)|lower == 'true' else false %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T: {new_t}, X: {new_x}, Y: {new_y}, Z: {new_z}, PARK_T0: {park_t0}, PARK_T1: {park_t1}, IS_PRINTING_GCODE: {is_printing_gcode}, TOOLSHIFT: {toolshift}"
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	{% if park_t0 >= 0 and park_t1 >= 0 %}
	{% set parking_position_t0 = park_t0 %}
	{% set parking_position_t1 = park_t1 %}
	{% set parking_position_act_t = park_t0 if act_t == 0 else park_t1 %}
	{% endif %}
	
	
	{% if not is_printing_gcode and not toolshift %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Changing tool to T{new_t} without retracting/extruding or moving the toolheads except for parking."
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	G90
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% if not is_printing_gcode and toolshift and new_x < 0 and new_y < 0 %}
	{% set new_x = center_x %}
	{% set new_y = printer.gcode_move.gcode_position.y|float %}
	{% endif %}
	
	{% if new_x < 0 or new_y < 0 %}
	
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="No new X or Y position given, parking the active toolhead and activating the new toolhead without moving it."
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={new_t}
	
	
	{% if "x" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	{% if is_printing_gcode %}
	_EXTRUDE T={new_t}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	{% if "xyz" not in printer.toolhead.homed_axes %}
	
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	
	
	{% set svv = printer.save_variables.variables %}
	{% if new_t == default_toolhead %}
	{% set new_xoffset = 0 %}
	{% set new_yoffset = 0 %}
	{% set new_zoffset = 0 %}
	{% else %}
	{% set new_xoffset = -svv.idex_xoffset %}
	{% set new_yoffset = -svv.idex_yoffset %}
	{% set new_zoffset = -svv.idex_zoffset %}
	{% endif %}
	
	{% set xoffset_correction = new_xoffset - printer.named_offsets.toolhead_alignment.x %}
	{% set yoffset_correction = new_yoffset - printer.named_offsets.toolhead_alignment.y %}
	{% set zoffset_correction = new_zoffset - printer.named_offsets.toolhead_alignment.z %}
	
	{% if new_t == 0 %}
	
	{% set t0_act_x = parking_position_t0 %}
	{% set t1_act_x = printer.toolhead.position.x|float %}
	{% set t0_new_x = new_x %}
	{% set t1_new_x = parking_position_t1 %}
	{% set t0_distance = t0_new_x - t0_act_x %}
	{% set t1_distance = t1_new_x - t1_act_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T0."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	
	
	G1 X{t0_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x + (t1_new_x - t1_act_x)} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t0_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T0: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% elif new_t == 1 %}
	
	{% set t0_act_x = printer.toolhead.position.x|float %}
	{% set t1_act_x = parking_position_t1 %}
	{% set t0_new_x = parking_position_t0 %}
	{% set t1_new_x = new_x %}
	{% set t0_distance = t0_act_x - t0_new_x %}
	{% set t1_distance = t1_act_x - t1_new_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T1."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x - t1_distance + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t1_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T1: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% endif %}
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	{% endif %}

[gcode_macro _ZHOP_BEFORE_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_hop = params.Z_HOP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_HOP: {z_hop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="COMBINED_ZHOP G1 Z+{z_hop} E-{e} F{speed * 60}"
	G1 Z+{z_hop} E-{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="ZHOP G1 Z+{z_hop} F{speed * 60}"
	G1 Z+{z_hop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="RETRACT G1 E-{e} F{feedrate}"
	G1 E-{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _ZDROP_AFTER_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_drop = params.Z_DROP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_DROP: {z_drop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="COMBINED_ZDROP G1 Z-{z_drop} E{e} F{speed * 60}"
	G1 Z-{z_drop} E{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="ZDROP G1 Z-{z_drop} F{speed * 60}"
	G1 Z-{z_drop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="EXTRUDE G1 E{e} F{feedrate}"
	G1 E{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _EXTRUDE]
gcode = 
	
	{% set t = params.T|int %}
	
	
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	
	DEBUG_ECHO PREFIX="_EXTRUDE" MSG="G1 E{e} F{feedrate * 60}"
	
	
	G91
	M82
	G92 E0
	G1 E{e} F{feedrate * 60}
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _DEACTIVATE_TOOLHEAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_DEACTIVATE_TOOLHEAD" MSG="TOOLHEAD {toolhead}"
	
	
	{% if toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% endif %}
	
	
	M106.1 S0
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={toolhead}

[delayed_gcode _INIT_TOOLHEADS]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	_IDEX_SINGLE INIT=1
	
	
	{% if printer.fastconfig.settings.dual_carriage.safe_distance is defined %}
	{% if printer.fastconfig.settings.dual_carriage.safe_distance|float < 50 %}
	{ action_emergency_stop("Dual carriage safe_distance seems to be too low!") }
	{% endif %}
	{% else %}
	{ action_emergency_stop("Dual carriage safe_distance not defined!") }
	{% endif %}

[gcode_macro _SET_TOOLHEAD_OFFSET]
description = "Internal use only. Sets the toolhead_alignment offset (and hotend_thermal_expansion offset when configured) for the active/dominant toolhead."
gcode = 
	
	{% set move = params.MOVE|default(0)|int %}
	{% set force_toolhead = params.FORCE_TOOLHEAD|default(-1)|int %}
	
	
	{% if params.T is defined %}
	CONSOLE_ECHO TYPE="error" MSG="_SET_TOOLHEAD_OFFSET called with deprectated T parameter, which is ignored."
	{';$_SET_TOOLHEAD_OFFSET_ignoring_TOOLHEAD_parameter'}
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="active/dominant toolhead: {toolhead}, MOVE: {move}, FORCE_TOOLHEAD: {force_toolhead}"
	
	
	{% if force_toolhead >= 0 %}
	{% set toolhead = force_toolhead %}
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="FORCE_TOOLHEAD applied, using TOOLHEAD: {toolhead}"
	{% endif %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set move = 0 %}
	{% endif %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|int %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X=0 Y=0 MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z=0 MOVE={move} SPEED={z_speed}
	{% else %}
	{% set svv = printer.save_variables.variables %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X={(-svv.idex_xoffset)} Y={(-svv.idex_yoffset)} MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-svv.idex_zoffset)} MOVE={move} SPEED={z_speed}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}

[gcode_macro TOOLSHIFT_CONFIG]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={params.SPEED|default(300)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={params.ACCEL|default(5000)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_retraction VALUE={params.RETRACT|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_extrusion VALUE={params.EXTRUDE|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_feedrate VALUE={params.FEEDRATE|default(7200)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={params.Z_HOP|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zspeed VALUE={params.Z_SPEED|default(25)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_combined_zhop VALUE={true if params.COMBINED_ZHOP|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_sync_fans VALUE={true if params.SYNC_FANS|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_prepurging_timer VALUE={params.AUTO_PURGE_TIME|default(0)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_purge VALUE={params.PURGE|default(25)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_standby_temp VALUE={params.STANDBY_TEMP|default(-1)|float}

[gcode_macro CALCULATE_DC_ENDSTOP]
description = "DEPRECATED: This macro has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."
gcode = 
	CONSOLE_ECHO TITLE="CALCULATE_DC_ENDSTOP has been deprecated" TYPE="error" MSG="The CALCULATE_DC_ENDSTOP has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."

[gcode_macro _VAOC]
variable_is_fixed = True
variable_is_started = False
variable_is_started_at_temp = False
variable_additional_safe_distance = 50
variable_safe_z = 30
variable_auto_z_offset_calibration = True
variable_enable_camera_cooling = True
variable_camera_cooling_fan_speed = 0.3
variable_camera_cooling_temperature = 50
variable_toolchange_travel_speed = 300
variable_toolchange_travel_accel = 5000
variable_adjusting_secondary_toolhead_focus_adjusts_zoffset = False
variable_cache_toolchange_travel_speed = 300
variable_cache_toolchange_travel_accel = 5000
variable_cache_toolchange_zhop = 1.0
variable_t0_toolhead_sensor_enabled = 0
variable_t1_toolhead_sensor_enabled = 0
variable_t0_bowden_sensor_enabled = 0
variable_t1_bowden_sensor_enabled = 0
variable_loaded_skew_profile = ""
variable_gcode_z_offset = 0.0
variable_start_x_offset = 0.0
variable_start_y_offset = 0.0
gcode = 
	_ECHO_VAOC_VARS
variable_expected_camera_x_position = 212.5
variable_expected_camera_y_position = 530.5

[gcode_macro _VAOC_START]
description = Called from the front end. If T0_TEMP, T1_TEMP and BED_TEMP parameter are specified, VAOC calibration will start under real conditions at printing temp.
gcode = 
	
	{% set t0_temp = params.T0_TEMP|default(0)|int %}
	{% set t1_temp = params.T1_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(0)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro SKEW_PROFILE"].loaded_profile|default("") %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=loaded_skew_profile VALUE='"{loaded_skew_profile}"'
	
	
	{% if t0_temp > 0 and t1_temp > 0 and bed_temp > 0 %}
	
	
	{% if not is_fixed %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("VAOC calibration at temp works only with a fixed installed VAOC device.") }
	{% endif %}
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE=0
	{% endif %}
	
	
	START_PRINT EXTRUDER_TEMP={t0_temp},{t1_temp} EXTRUDER_OTHER_LAYER_TEMP={t0_temp},{t1_temp} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp} INITIAL_TOOL=0 TOTAL_LAYER_COUNT=1 X0={(printable_x_max / 2 - 10)} Y0={(printable_y_max / 2 - 10)} X1={(printable_x_max / 2 + 10)} Y1={(printable_y_max / 2 + 10)} TOTAL_TOOLSHIFTS=1 FIRST_X={printable_x_max / 2} FIRST_Y={printable_y_max / 2} MIN_X={(printable_x_max / 2 - 10)} MAX_X={(printable_x_max / 2 + 10)} USED_TOOLS=0,1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=True
	
	{% endif %}
	
	
	_START_VAOC

[gcode_macro _START_VAOC]
description = Called from _VAOC_START. Do not call it manually.
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(printable_x_max/2)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(printable_y_max/2)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	DEBUG_ECHO PREFIX="VAOC_START" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, zcontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_x_offset VALUE={svv.idex_xoffset|default(0.0)|float}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_y_offset VALUE={svv.idex_yoffset|default(0.0)|float}
	
	
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_SAFE_Z_HEIGHT
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_speed VALUE={printer["gcode_macro RatOS"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_accel VALUE={printer["gcode_macro RatOS"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_zhop VALUE={printer["gcode_macro RatOS"].toolchange_zhop|float}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE=0
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"START X_REFERENCE:%.6f Y_REFERENCE:%.6f Z_REFERENCE:%.6f PARK_T0:%.6f PARK_T1:%.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, parking_position_t0, parking_position_t1)}
	
	
	_LED_VAOC_ON
	
	
	
	
	
	
	
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=gcode_z_offset VALUE={printer.gcode_move.homing_origin.z}
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z=0
	
	
	MAYBE_HOME
	M400
	
	
	_LOAD_RATOS_SKEW_PROFILE
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	IDEX_SINGLE
	{% endif %}
	
	
	
	SAVE_GCODE_STATE NAME=vaoc_state
	
	
	RESET_NAMED_OFFSET EVENT=reset_all
	
	
	{% if is_fixed %}
	_SELECT_TOOL T=0 TOOLSHIFT=false
	{% if default_toolhead == 0 %}
	G1 X{idex_xcontrolpoint} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint + safe_distance + additional_safe_distance} F{speed}
	{% else %}
	G1 X{idex_xcontrolpoint - safe_distance - additional_safe_distance} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint} F{speed}
	{% endif %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	{% else %}
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	G1 X{idex_xcontrolpoint} F{speed}
	G1 Y{idex_ycontrolpoint} F{speed}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	
	
	_SELECT_TOOL T={default_toolhead} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	{% if not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={default_toolhead}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=True

[gcode_macro _VAOC_END]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_y = printable_y_max / 2 %}
	{% set saved_gcode_z_offset = printer["gcode_macro _VAOC"].gcode_z_offset|default(0.0)|float %}
	
	DEBUG_ECHO PREFIX="_VAOC_END" MSG="printable_y_max: {printable_y_max}, center_y: {center_y}, safe_z: {safe_z}"
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% set x_offset_change = svv.idex_xoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_x_offset|default(0.0)|float %}
	{% set y_offset_change = svv.idex_yoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_y_offset|default(0.0)|float %}
	{% set offset_change_norm = (x_offset_change ** 2 + y_offset_change ** 2) ** 0.5 %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="VAOC calibration changed the relative XY offset between T0 and T1 by {offset_change_norm|round(3)} mm (ΔX: {x_offset_change|round(3)}, ΔY: {y_offset_change|round(3)})"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	G1 Y{center_y} F{speed}
	
	
	_IDEX_SINGLE INIT=1
	
	
	_LED_VAOC_OFF
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={printer["gcode_macro _VAOC"].cache_toolchange_zhop|float}
	
	
	{% if printer["gcode_macro _VAOC"].is_started_at_temp|default(true)|lower == 'true' %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_bowden_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_bowden_sensor_enabled|int}
	{% endif %}
	{% endif %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro _VAOC"].loaded_skew_profile|default("") %}
	{% if loaded_skew_profile != "" %}
	SKEW_PROFILE LOAD={loaded_skew_profile}
	{% else %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=vaoc_state
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z={saved_gcode_z_offset}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False

[gcode_macro _VAOC_LOAD_TOOL]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set auto_temp_offset = true if params.AUTO_TEMP_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set toolhead_zoffset = svv.idex_zoffset|default(0)|float %}
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move T%s to control point: X%.6f Y%.6f Z%.6f IS_FIXED=%s"' % (t, idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, is_fixed)}
	
	
	{% if not auto_temp_offset and not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={t}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	{% set current_z = printer.toolhead.position.z|float %}
	{% set lowest_toolhead_z = [current_z, current_z - toolhead_zoffset]|min %}
	{% if lowest_toolhead_z < safe_z %}
	G1 Z{[safe_z, safe_z + toolhead_zoffset]|max} F{z_speed}
	{% else %}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	{% endif %}
	
	
	_SELECT_TOOL T={t} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_SET_CAMERA_COOLING]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	
	
	{% set enable_camera_cooling = true if printer["gcode_macro _VAOC"].enable_camera_cooling|default(true)|lower == 'true' else false %}
	{% set camera_cooling_temperature = printer["gcode_macro _VAOC"].camera_cooling_temperature|float %}
	{% set camera_cooling_fan_speed = printer["gcode_macro _VAOC"].camera_cooling_fan_speed|float %}
	
	
	{% if printer.heater_bed.temperature >= camera_cooling_temperature and enable_camera_cooling %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={camera_cooling_fan_speed if t == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={camera_cooling_fan_speed if t == 1 else 0}
	
	
	M106.1 S{camera_cooling_fan_speed}
	
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	{% endif %}

[gcode_macro _VAOC_SET_TOOL]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="_VAOC_SET_TOOL" MSG="IDEX_MODE: {idex_mode}, TOOLHEAD: {toolhead}"
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	{% set x = printer.gcode_move.gcode_position.x|float %}
	{% set y = printer.gcode_move.gcode_position.y|float %}
	{% set z = printer.gcode_move.gcode_position.z|float %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE={x}
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE={y}
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE={z}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Control point was set: X%.6f Y%.6f Z%.6f"' % (x, y, z)}
	
	{% else %}
	
	
	
	{% set move_diff_x = printer.gcode_move.gcode_position.x|float - svv.idex_xcontrolpoint|float %}
	{% set move_diff_y = printer.gcode_move.gcode_position.y|float - svv.idex_ycontrolpoint|float %}
	{% set move_diff_z = printer.gcode_move.gcode_position.z|float - svv.idex_zcontrolpoint|float %}
	
	
	{% set new_x_offset = svv.idex_xoffset - move_diff_x %}
	{% set new_y_offset = svv.idex_yoffset - move_diff_y %}
	{% set new_z_offset = svv.idex_zoffset - move_diff_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE={new_x_offset}
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE={new_y_offset}
	
	{% set z_focus_msg = "" %}
	{% if move_diff_z|abs > 1e-6 %}
	{% if printer["gcode_macro _VAOC"].adjusting_secondary_toolhead_focus_adjusts_zoffset|default(false)|lower == 'true' %}
	{% set z_focus_msg = " (Z offset adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={new_z_offset}
	{% else %}
	{% set z_focus_msg = " (Z offset not adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	{% set new_z_offset = svv.idex_zoffset %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset was set: X%.6f Y%.6f Z%.6f%s"' % (toolhead, new_x_offset, new_y_offset, new_z_offset, z_focus_msg)}
	
	{% endif %}

[gcode_macro _VAOC_MOVE]
gcode = 
	
	{% set x = params.X|default(0)|float %}
	{% set y = params.Y|default(0)|float %}
	{% set z = params.Z|default(0)|float %}
	
	
	G91
	{% if z != 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 Z%.6f F300"' % (z)}
	G1 Z{z} F300
	
	{% else %}
	{% if x <=2 and y <=2 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 X%.6f Y%.6f F18000"' % (x, y)}
	G1 X{x} Y{y} F18000
	{% endif %}
	{% endif %}
	G90

[gcode_macro _VAOC_CALIBRATE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	{% if printer["z_offset_probe"] is defined and is_started %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	
	{% if auto_z_offset %}
	_START_VAOC AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_END
	{% else %}
	_VAOC_LOAD_TOOL T={default_toolhead}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	{% endif %}
	
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_Z_OFFSET
	
	{% endif %}

[gcode_macro _VAOC_PROBE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}
	{% if not auto_z_offset %}
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	{% endif %}
	M400
	_VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT

[gcode_macro _VAOC_Z_OFFSET_PROBE_CURRENT_POSITION]
gcode = 
	
	Z_OFFSET_PROBE PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_DROP=1 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median

[gcode_macro _VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT]
gcode = 
	{% if printer["z_offset_probe"] is defined %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE={last_z}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Z-offset control point set:: %.6f"' % last_z}
	
	{% else %}
	
	
	
	{% set z = svv.idex_zoffsetcontrolpoint|float - last_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={z}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-z)}
	
	
	G0 Z{svv.idex_zcontrolpoint|float} F{z_speed}
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset set: Z %.6f"' % (t, z)}
	
	{% endif %}
	
	{% endif %}

[gcode_macro _VAOC_ECHO_Z_OFFSET]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s toolhead z-offset %.6f"' % (1 if default_toolhead == 0 else 0, svv.idex_zoffset)}
	{% if svv.idex_zoffset|abs < 0.02 %}
	CONSOLE_ECHO TITLE={'"Perfect toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="You have a perfect toolhead z-offset!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.02 and svv.idex_zoffset|abs < 0.05 %}
	CONSOLE_ECHO TITLE={'"Good toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is good!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.05 and svv.idex_zoffset|abs < 0.1 %}
	CONSOLE_ECHO TITLE={'"High toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset could be better._N_Use minimum 0.3mm first layer height for copy and mirror mode prints." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.1 and svv.idex_zoffset|abs < 0.2 %}
	CONSOLE_ECHO TITLE={'"Bad toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is bad._N_Copy and mirror mode prints are not recommended with it." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.2 %}
	CONSOLE_ECHO TITLE={'"Unacceptable toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is unacceptable._N_Do not print in copy and mirror mode with it." TYPE="alert"
	{% endif %}
	RATOS_ECHO PREFIX="VAOC" MSG="Toolhead z-offset calibration done!"

[gcode_macro _VAOC_CALIBRATE_TEMP_OFFSET]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if is_fixed and is_started and printer["z_offset_probe"] is defined and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	_VAOC_LOAD_TOOL T={default_toolhead} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_NOZZLE_TEMP_OFFSETS
	
	{% endif %}

[gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET=0
	
	
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	M400

[gcode_macro _VAOC_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(150)|float %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Probing with nozzle temperature {temp}°C..."
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	
	
	G0 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _VAOC_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set msg = '"T0 expansion coefficient %.6fmm_N_T1 expansion coefficient %.6fmm"' % (svv.nozzle_expansion_coefficient_t0, svv.nozzle_expansion_coefficient_t1) %}
	CONSOLE_ECHO TITLE="Nozzle expansion coefficients:" MSG={msg} TYPE="success"

[gcode_macro _VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - expected_camera_x_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC x-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_xcontrolpoint, expected_camera_x_position)) }
	{% endif %}
	{% if (idex_ycontrolpoint - expected_camera_y_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC y-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_ycontrolpoint, expected_camera_y_position)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - printer.gcode_move.gcode_position.x|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected y-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_xcontrolpoint, printer.gcode_move.gcode_position.x|float)) }
	{% endif %}
	{% if (idex_ycontrolpoint - printer.gcode_move.gcode_position.y|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected x-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_ycontrolpoint, printer.gcode_move.gcode_position.y|float)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_SAFE_Z_HEIGHT]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set idex_zoffsetcontrolpoint = svv.idex_zoffsetcontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_SAFE_Z_HEIGHT" MSG={'"idex_zcontrolpoint: %.6f, idex_zoffsetcontrolpoint: %.6f"' % (idex_zcontrolpoint, idex_zoffsetcontrolpoint)}
	
	{% if safe_z < idex_zcontrolpoint + 2 or safe_z < idex_zoffsetcontrolpoint + 2 %}
	{action_raise_error("VAOC safe_z value (%.3f) is too low, it must be higher than %.3f" % (safe_z, [idex_zoffsetcontrolpoint + 2, idex_zcontrolpoint + 2]|max))}
	{% endif %}

[gcode_macro _VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED]
gcode = 
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T0. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T1. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_RESET]
gcode = 
	DEBUG_ECHO PREFIX="_VAOC_RESET" MSG="running template-emitted _VAOC_RESET macro"
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE=212.5
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE=530.5
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE=10
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE=0
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE=0.0
	
	RESET_DC_ENDSTOP_CONFIGURATION
	RESET_Y_MAX_ADJUSTMENT
	
	
	CONSOLE_ECHO TITLE="VAOC Configuration Reset" MSG="VAOC configuration has been reset. You must RESTART klipper for the changes to take effect,_N_then re-calibrate VAOC."

[gcode_macro _ECHO_VAOC_VARS]
description = Echo VAOC variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro _VAOC"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro _VAOC_SWITCH_LED]
gcode = 
	{% if params.STATE|default(0)|int == 1 %}
	_LED_VAOC_ON
	{% else %}
	_LED_VAOC_OFF
	{% endif %}

[gcode_macro Z_PROBE_TEST_T0]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T0
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST_T1]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T1
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	
	
	_VAOC_Z_PROBE_TEST_EVALUATE
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro _VAOC_Z_PROBE_LOOP]
gcode = 
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_SHAKE_IT
	_VAOC_START

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if primary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T0. Retried {primary_retries} time(s)."
	{% endif %}
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	
	{% if (primary_range - secondary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 is drifting significantly more than T1."
	{% endif %}
	{% if (secondary_range - primary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 is drifting significantly more than T0."
	{% endif %}
	
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T0]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T1]
gcode = 
	
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _SHAKE_IT]
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	_Z_HOP
	{% for i in range(3) %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 + 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 + 1}
	{% endfor %}
	{% for i in range(2) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 + 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 + 50}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 1}
	{% endfor %}
	{% endfor %}

[gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 retries updated: {new_retries}"

[gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 retries updated: {new_retries}"

[gcode_macro _CLEAR_PRIMARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _CLEAR_SECONDARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _VAOC_TEST_Z_OFFSET]
gcode = 
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}

[delayed_gcode _IDEX_INIT]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	VERIFY_HYBRID_INVERTED

[gcode_macro Z_TILT_ADJUST]
rename_existing = Z_TILT_ADJUST_ORIG
gcode = 
	
	{% set beacon_contact_z_tilt_adjust_samples = printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust_samples|default(2)|int %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(true)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	_IDEX_SINGLE
	
	_SELECT_TOOL T={printer["gcode_macro RatOS"].default_toolhead|default(0)|int} TOOLSHIFT=false
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_tilt_adjust %}
	Z_TILT_ADJUST_ORIG PROBE_METHOD=contact SAMPLES={beacon_contact_z_tilt_adjust_samples}
	{% else %}
	Z_TILT_ADJUST_ORIG
	{% endif %}
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if idex_mode == "copy" %}
	_IDEX_COPY
	{% elif idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[stepper_x]
position_max = 500
position_endstop = -59.6
position_min = -59.6
step_pin = PF13
dir_pin = x_dir_pin
enable_pin = !PF14
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t0:PA2

[stepper_y]
position_max = 533.65
position_min = -14.35
position_endstop = -14.35
step_pin = PG0
dir_pin = !y_dir_pin
enable_pin = !PF15
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = PG9

[stepper_z]
position_max = 500
position_min = -7
step_pin = PC13
dir_pin = !z0_dir_pin
enable_pin = !PF1
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4
homing_speed = 10
endstop_pin = probe:z_virtual_endstop

[z_tilt]
z_positions = 
	0,0
	250,500
	500,0
points = 
	20, 10
	480, 230
	20, 450
horizontal_move_z = 20
retries = 10
retry_tolerance = 0.02
speed = 600

[extruder]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t0:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t0:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t0:PD3
dir_pin = toolboard_t0:e_dir_pin
enable_pin = !toolboard_t0:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[firmware_retraction]
retract_speed = 60
unretract_extra_length = 0
unretract_speed = 60
retract_length = 0.2

[extruder1]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t1:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t1:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t1:PD3
dir_pin = toolboard_t1:e_dir_pin
enable_pin = !toolboard_t1:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[resonance_tester]
accel_chip_x = lis2dw toolboard_t0
accel_chip_y = lis2dw toolboard_t0
probe_points = 
	250,250,20

[tmc5160 stepper_x]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC4
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 dual_carriage]
stealthchop_threshold = 0
interpolate = True
cs_pin = PF2
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y]
stealthchop_threshold = 0
interpolate = True
cs_pin = PD11
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y1]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC7
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[stepper_y1]
step_pin = PG4
dir_pin = y1_dir_pin
enable_pin = !PA2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46

[tmc2209 stepper_z]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE4
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[tmc2209 stepper_z1]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE1
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z1]
step_pin = PE2
dir_pin = !z1_dir_pin
enable_pin = !PD4
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 stepper_z2]
stealthchop_threshold = 0
interpolate = True
uart_pin = PD3
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z2]
step_pin = PE6
dir_pin = !z2_dir_pin
enable_pin = !PE0
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 extruder]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t0:PB3
run_current = 0.707
sense_resistor = 0.11

[tmc2209 extruder1]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t1:PB3
run_current = 0.707
sense_resistor = 0.11

[beacon]
serial = /dev/beacon
x_offset = 0
y_offset = 27.5
mesh_main_direction = x
mesh_runs = 1
mesh_cluster_size = 0
speed = 15.
lift_speed = 80.
contact_max_hotend_temperature = 275
contact_mesh_min = 20,20
contact_mesh_max = 480,480

[beacon_user_z_offset]

[beacon_mesh]

[beacon_true_zero_correction]

[beacon_adaptive_heat_soak]

[delayed_gcode _BEACON_INIT]
initial_duration = 1
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	_BEACON_MESH_INIT
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_coefficient_multiplier
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_applied_offset
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=beacon_saved_runtime_offset
	{% if printer["gcode_macro RatOS"].beacon_contact_expansion_multiplier is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_contact_expansion_multiplier is no longer used, please remove it from your config file."
	{% endif %}
	{% if printer["gcode_macro RatOS"].beacon_scan_compensation_resolution is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_scan_compensation_resolution is no longer used, please remove it from your config file."
	{% endif %}

[gcode_macro BEACON_RATOS_CALIBRATION]
gcode = 
	RATOS_ECHO MSG="Did you mean BEACON_RATOS_CALIBRATE?"

[gcode_macro BEACON_RATOS_CALIBRATE]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	BEACON_INITIAL_CALIBRATION _AUTOMATED=True
	
	{% if beacon_contact_start_print_true_zero %}
	BEACON_POKE_TEST _AUTOMATED=True
	_BEACON_CHECK_POKE
	{% if printer["dual_carriage"] is not defined %}
	BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET _AUTOMATED=True
	{% endif %}
	{% endif %}
	
	{% set already_heated = False %}
	
	
	{% if beacon_contact_start_print_true_zero and beacon_scan_compensation_enable %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% set already_heated = True %}
	{% endif %}
	
	
	BEACON_FINAL_CALIBRATION _AUTOMATED=True _AUTOMATED_ALREADY_HEATED={already_heated} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	{% if beacon_contact_start_print_true_zero %}
	{% if printer["dual_carriage"] is not defined %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	_BEACON_ECHO_POKE
	{% endif %}
	RATOS_ECHO MSG="Beacon calibration finished!"
	
	
	_LED_BEACON_CALIBRATION_END
	
	
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG

[gcode_macro BEACON_INITIAL_CALIBRATION]
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Initial beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro BEACON_FINAL_CALIBRATION]
description = Runs BEACON_AUTO_CALIBRATE after heating the bed and chamber to specified temperatures. This creates a beacon model under reference conditions for future use.
	This macro will skip calibration if both the beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero settings are enabled, because a new
	model will be calibrated automatically at the start of each print. Use FORCE=True to override this check.
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set already_heated = true if params._AUTOMATED_ALREADY_HEATED|default(false)|lower == 'true' else false %}
	{% set force = params.FORCE|default('false')|lower in ('1', 'true', 'yes') %}
	
	
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default('false')|lower == "true" %}
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero and not force %}
	RATOS_ECHO MSG="BEACON_FINAL_CALIBRATION skipped, not needed because beacon_contact_calibrate_model_on_true_zero is enabled. Use FORCE=True to override."
	{% else %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	{% if chamber_temp > 0 and not already_heated %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	{% if not already_heated %}
	
	G0 Z2.5 F{z_hop_speed}
	
	
	RATOS_ECHO MSG="Waiting for calibration temperature..."
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	{% if beacon_adaptive_heat_soak %}
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,3600]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_Z_HOP
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Final beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	{% endif %}

[gcode_macro BEACON_POKE_TEST]
variable_poke_result_1 = -1
variable_poke_result_2 = -1
variable_poke_result_3 = -1
variable_poke_result_4 = -1
variable_poke_result_5 = -1
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_1 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_2 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_3 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_4 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_5 VALUE=-1
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G0 Z5 F{z_hop_speed}
	
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=1
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=2
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=3
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=4
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=5
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Beacon poke test finished!"
	{% if not automated %}
	_BEACON_ECHO_POKE
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro _BEACON_PROBE_POKE]
gcode = 
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	BEACON_POKE speed=3 top=5 bottom={poke_bottom}
	BEACON_QUERY

[gcode_macro _BEACON_STORE_POKE]
gcode = 
	
	{% set i = params.I|default(1)|int %}
	
	
	{% set last_z = printer.beacon.last_poke_result|default(0)|float %}
	
	
	{% if printer.beacon.last_poke_result|lower != "none" %}
	{% if printer.beacon.last_poke_result.error == 0 %}
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE={"poke_result_%s" % i} VALUE={printer.beacon.last_poke_result.latency}
	{% endif %}
	{% endif %}

[gcode_macro _BEACON_CHECK_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% if p1 == -1 or p2 == -1 or p3 == -1 or p4 == -1 or p5 == -1 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test error!") }
	{% endif %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	{% if avg > 6 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test failed!") }
	{% endif %}

[gcode_macro _BEACON_ECHO_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	
	
	{% if avg <= 1 %}
	{% set type = "success" %}
	{% set note = "Extremely low noise, rarely achieved" %}
	{% elif avg > 1 and avg <= 4 %}
	{% set type = "info" %}
	{% set note = "Excellent performance for a typical printer" %}
	{% elif avg > 4 and avg <= 8 %}
	{% set type = "warning" %}
	{% set note = "Acceptable performance, machine may have considerable cyclic axis noise" %}
	{% elif avg > 8 and avg <= 11 %}
	{% set type = "alert" %}
	{% set note = "Not ideal, may want to verify proper mounting or use thinner stackups" %}
	{% elif avg > 11 %}
	{% set type = "alert" %}
	{% set note = "Reason for concern, present setup may be risky to continue with" %}
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon poke test result:" TYPE={type} MSG={'"Average latency: %.2f_N_%s"' % (avg, note)}

[gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Nozzle temperature offset calibration..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET=0
	
	
	{% if not automated %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing with nozzle temperature {temp}°C..."
	PROBE PROBE_METHOD=contact PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median
	BEACON_QUERY
	
	
	G0 Z5 F{z_speed}

[gcode_macro _BEACON_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer.beacon.last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{default_toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% if default_toolhead == 0 %}
	CONSOLE_ECHO TYPE="info" MSG={'"T0 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t0}
	{% else %}
	CONSOLE_ECHO TYPE="info" MSG={'"T1 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t1}
	{% endif %}

[gcode_macro _BEACON_SET_NOZZLE_TEMP_OFFSET]
description = "Set the thermal expansion z offset for the active toolhead based on the current extruder target temperature and thermal expansion coefficient."
gcode = 
	{% if params.RESET is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The RESET parameter is no longer supported and has no effect."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% if params.TOOLHEAD is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The TOOLHEAD parameter is no longer supported and has no effect. The macro now automatically determines the current toolhead."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	{% if beacon_contact_expansion_compensation %}
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set nozzle_expansion_coefficient_t0 = svv.nozzle_expansion_coefficient_t0|default(0)|float %}
	{% if printer["dual_carriage"] is defined %}
	{% set nozzle_expansion_coefficient_t1 = svv.nozzle_expansion_coefficient_t1|default(0)|float %}
	{% endif %}
	
	
	{% set temp = printer['extruder' if toolhead == 0 else 'extruder1'].target|float %}
	
	
	{% set temp_delta = temp - beacon_contact_true_zero_temp %}
	{% set expansion_coefficient = nozzle_expansion_coefficient_t0 if toolhead == 0 else nozzle_expansion_coefficient_t1 %}
	{% set expansion_offset = temp_delta * (expansion_coefficient / 100) %}
	
	
	SET_NAMED_OFFSET NAME=hotend_thermal_expansion Z={expansion_offset} MOVE=1 MOVE_SPEED={z_speed}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG={'"Nozzle expansion offset of %.6fmm applied to T%s"' % (expansion_offset, toolhead)}
	DEBUG_ECHO PREFIX="_BEACON_SET_NOZZLE_TEMP_OFFSET" MSG="toolhead: {toolhead}, coefficient: {expansion_coefficient|round(6)}, temp_delta: {temp_delta|round(1)},  expansion_offset: {expansion_offset|round(6)}"
	
	{% endif %}

[gcode_macro BEACON_MEASURE_BEACON_OFFSET]
variable_needs_compensation = False
variable_reference_z = 0.0
variable_front = 0.0
variable_front_left = 0.0
variable_front_right = 0.0
variable_back = 0.0
variable_back_left = 0.0
variable_back_right = 0.0
variable_right = 0.0
variable_left = 0.0
variable_margin_x = 40
variable_margin_y = 40
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=False
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Measure beacon offset..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="center"
	
	
	G0 X{margin_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_left"
	
	
	G0 X{safe_home_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front"
	
	
	G0 X{(printable_x_max - margin_x)} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_right"
	
	
	G0 X{safe_home_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back"
	
	
	G0 X{margin_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_left"
	
	
	G0 X{margin_x} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="left"
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_BEACON_ECHO_BEACON_OFFSET
	
	
	_LED_BEACON_CALIBRATION_END
	
	{% endif %}

[gcode_macro _BEACON_STORE_BEACON_OFFSET]
gcode = 
	
	{% set location = params.LOCATION|lower %}
	
	
	{% set last_z = printer.beacon.last_offset_result["delta"]|default(0)|float %}
	
	
	{% if location == "center" %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE={location} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_BEACON_OFFSET]
gcode = 
	
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float * 1000 %}
	{% set front_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_left|default(0)|float * 1000 %}
	{% set front = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front|default(0)|float * 1000 %}
	{% set front_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_right|default(0)|float * 1000 %}
	{% set right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].right|default(0)|float * 1000 %}
	{% set back_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_right|default(0)|float * 1000 %}
	{% set back = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back|default(0)|float * 1000 %}
	{% set back_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_left|default(0)|float * 1000 %}
	{% set left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].left|default(0)|float * 1000 %}
	
	{% set line_1 = "Front left:    %.6fμm" % (front_left) %}
	{% set line_2 = "Front center:  %.6fμm" % (front) %}
	{% set line_3 = "Front right:   %.6fμm" % (front_right) %}
	{% set line_4 = "Left center:   %.6fμm" % (left) %}
	{% set line_5 = "Right center:  %.6fμm" % (right) %}
	{% set line_6 = "Back left:     %.6fμm" % (back_left) %}
	{% set line_7 = "Back center:   %.6fμm" % (back) %}
	{% set line_8 = "Back right:    %.6fμm" % (back_right) %}
	
	{% set max_value = [(front_left|abs), (front|abs), (front_right|abs), (left|abs), (right|abs), (back_left|abs), (back|abs), (back_right|abs)]|max %}
	{% if max_value <= 50 %}
	{% set type = "success" %}
	{% set recommendation = "Very low beacon offset: %.6fμm._N_No beacon scan compensation needed." % max_value %}
	{% elif max_value > 50 and max_value <= 100 %}
	{% set type = "info" %}
	{% set recommendation = "Low beacon offset: %.6fμm._N_You may experience first layer inconsistensies, consider beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 100 and max_value <= 150 %}
	{% set type = "warning" %}
	{% set recommendation = "High beacon offset: %.6fμm._N_High chance of first layer problems, beacon scan compensation is highly encouraged." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 150 and max_value <= 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Very High beacon offset: %.6fμm._N_You will encounter first layer problems on large prints unless you activate beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Extremely high beacon offset: %.6fμm._N_You have significant scan/contact inconsistency which is indicative of mechanical problems, please investigate before resorting to software compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon offset relative to the center" TYPE={type} MSG={'"_N_%s_N__N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s"' % (recommendation, line_1, line_2, line_3, line_4, line_5, line_6, line_7, line_8)}

[gcode_macro BEACON_CREATE_SCAN_COMPENSATION_MESH]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set profile = params.PROFILE|default("auto")|string %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set keep_temp_meshes = params.KEEP_TEMP_MESHES|default(0) %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' %}
	{% set desired_spacing = printer["gcode_macro RatOS"].beacon_scan_compensation_desired_spacing|float %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	
	{% if not beacon_scan_compensation_enable %}
	RATOS_ECHO MSG="Beacon scan compensation is disabled!"
	
	{% else %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	
	
	RATOS_ECHO MSG="Please wait..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	G1 Z2.5 F{z_speed}
	{% if beacon_adaptive_heat_soak %}
	
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,9000]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if not (beacon_adaptive_heat_soak or bed_heat_soak_time > 0) %}
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if printer.z_tilt is defined %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% endif %}
	{% if printer.quad_gantry_level is defined %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% endif %}
	
	
	_BEACON_CREATE_SCAN_COMPENSATION_MESH_CORE PROFILE="{profile}" DESIRED_SPACING={desired_spacing} CHAMBER_TEMP={chamber_temp} KEEP_TEMP_MESHES={keep_temp_meshes}
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	{% if automated %}
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon scan compensation mesh created!"
	
	
	{% if not automated %}
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED]
gcode = 
	
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED" MSG="beacon_scan_compensation_profile {beacon_scan_compensation_profile}, beacon_scan_compensation_enable {beacon_scan_compensation_enable}"
	
	{% if beacon_scan_compensation_enable %}
	BEACON_APPLY_SCAN_COMPENSATION PROFILE="{beacon_scan_compensation_profile}"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL]
gcode = 
	
	{% set beacon_contact_start_print_true_zero = params.BEACON_CONTACT_START_PRINT_TRUE_ZERO|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = params.beacon_contact_calibrate_model_on_true_zero|lower == 'true' %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and not printer.beacon.model %}
	{% set beacon_model_required_for_true_zero = beacon_contact_start_print_true_zero and not beacon_contact_calibrate_model_on_true_zero %}
	{% set beacon_model_required_for_homing =
	printer.fastconfig.settings.stepper_z.endstop_pin == 'probe:z_virtual_endstop'
	and (( printer.fastconfig.settings.beacon.home_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower != 'true')
	or ( printer.fastconfig.settings.beacon.default_probe_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower != 'true' )) %}
	{% if beacon_model_required_for_homing or beacon_model_required_for_true_zero %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("An active Beacon model is required. Have you performed initial Beacon calibration?") }
	{% endif %}
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION]
gcode = 
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set bed_temp_mismatch_is_error = true if printer["gcode_macro RatOS"].beacon_scan_compensation_bed_temp_mismatch_is_error|default(false)|lower == 'true' else false %}
	
	{% set bed_temp = params.BED_TEMP|default(0)|float %}
	{% if bed_temp == 0 %}
	{% set bed_temp = printer.heater_bed.temperature %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_PREFLIGHT_CHECK_BEACON" MSG="beacon_scan_compensation_profile={beacon_scan_compensation_profile}, beacon_scan_compensation_enable={beacon_scan_compensation_enable}, bed_temp={bed_temp}"
	
	{% if beacon_scan_compensation_enable %}
	_VALIDATE_COMPENSATION_MESH_PROFILE PROFILE="{beacon_scan_compensation_profile}" TITLE="Check Beacon scan compensation profile" SUBJECT="Configured compensation profile '{beacon_scan_compensation_profile}'" COMPARE_BED_TEMP={bed_temp} COMPARE_BED_TEMP_IS_ERROR={bed_temp_mismatch_is_error}
	{% endif %}

[gcode_macro _BEACON_MAYBE_SCAN_COMPENSATION]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set needs_scan_compensation = true if printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].needs_compensation|default(false)|lower == 'true' else false %}
	
	{% if needs_scan_compensation %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% endif %}

[gcode_macro _BEACON_HOME_AND_ABL]
gcode = 
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	{% if needs_rehoming %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}

[gcode_macro SAVE_Z_OFFSET]
description = Deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead, or in Mainsail use the SAVE button in the Z-OFFSET section.
gcode = 
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default('false')|lower == 'true' %}
	{% set msg = "SAVE_Z_OFFSET is deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead,_N_or in Mainsail use the SAVE button in the Z-OFFSET section."%}
	{% if not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% set msg = msg + "_N_You must then use the SAVE_CONFIG command to persist the change." %}
	{% endif %}
	CONSOLE_ECHO TYPE="error" MSG="{msg}"

[gcode_macro _BEACON_OFFSET_COMPARE]
gcode = 
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing..."
	
	
	BEACON_OFFSET_COMPARE SAMPLES_DROP=1 SAMPLES=3
	BEACON_QUERY

[fan]
pin = rpi:gpio4

[fan_generic part_fan_t0]
pin = PA8
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[fan_generic part_fan_t1]
pin = PE5
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[heater_fan toolhead_cooling_fan_t0]
heater = extruder
shutdown_speed = 1
pin = toolboard_t0:PB4

[heater_fan toolhead_cooling_fan_t1]
heater = extruder1
shutdown_speed = 1
pin = toolboard_t1:PB4

[controller_fan controller_fan]
pin = dinghy:PA4
tachometer_pin = dinghy:PC15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[z_offset_probe]
pin = ^PG10
z_offset = -7
y_offset = 0
x_offset = 37.5
speed = 10
samples = 3
sample_retract_dist = 5
lift_speed = 10.0
samples_result = median
samples_tolerance = 0.2
samples_tolerance_retries = 5

[neopixel vaoc_led]
pin = PB10
chain_count = 6
color_order = GRB

[heater_fan vaoc_fan]
pin = PD13
heater = heater_bed
fan_speed = 1.0
heater_temp = 50

[fan_generic filter]
pin = !PD14
enable_pin = PD15

[gcode_macro T0]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = True
variable_color = "7bff33"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = -32.6
variable_parking_position = -57.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=0 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[gcode_macro T1]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = False
variable_color = "0ea5e9"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = 532.6
variable_parking_position = 557.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=1 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[save_variables]
filename = /home/pi/printer_data/config/ratos-variables.cfg

[mcu dinghy]
serial = /dev/serial/by-id/usb-Klipper_stm32f072xb_Dragon_dinghy-if00

[temperature_sensor th0]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA0

[temperature_sensor th1]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA1

[temperature_sensor th2]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA2

[temperature_sensor th3]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA3

[controller_fan CTL2]
pin = dinghy:PB14
tachometer_pin = dinghy:PB15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[mcu plasma]
serial = /dev/serial/by-id/usb-Klipper_rp2040_Plasma-if00

[neopixel Chamber_Lights]
pin = plasma:gpio15
chain_count = 140
color_order = GRBW
initial_red = 0.0
initial_green = 0.0
initial_blue = 0.0
initial_white = 0.1

[beacon model default]
model_coef = 1.5287863993594841,
	1.9289099639750602,
	0.8838828622507556,
	0.25554883784260735,
	-0.015171504024913506,
	0.3044946127013882,
	0.15820427856566457,
	-0.25262403959326246,
	0.042488512846660914,
	0.16662470122520964
model_domain = 1.842634574664148e-07,1.9339206373083917e-07
model_range = 0.200000,5.000000
model_temp = 13.222247
model_offset = 0.00000

[bed_mesh default]
version = 1
points = 
	0.016163, 0.016713, 0.001923, -0.017658, -0.031574, -0.032498, -0.030898, -0.032177, -0.035213, -0.031148, -0.021322, -0.016924, -0.015012, -0.013911, -0.012197, -0.012583, -0.010489, -0.007529, -0.003986, -0.000980, 0.005518, 0.014442, 0.027426, 0.034677, 0.037410, 0.040391, 0.041842, 0.040369, 0.037615, 0.030776, 0.027664, 0.022856, 0.016892, 0.015398, 0.014717, 0.006921, 0.001532, 0.000731, 0.008657, 0.014036
	0.005356, -0.005066, -0.016998, -0.029668, -0.038334, -0.043672, -0.041139, -0.042488, -0.045199, -0.039432, -0.028746, -0.023642, -0.024058, -0.022802, -0.019679, -0.018514, -0.018102, -0.016476, -0.012722, -0.010077, -0.001809, 0.007180, 0.019853, 0.027754, 0.029964, 0.033626, 0.036783, 0.032018, 0.029372, 0.020847, 0.017634, 0.011926, 0.009013, 0.009254, 0.007972, -0.001380, -0.006940, -0.002160, 0.006135, 0.008330
	-0.004900, -0.006720, -0.021914, -0.039691, -0.050459, -0.050377, -0.046281, -0.048755, -0.054708, -0.051499, -0.033927, -0.027632, -0.030243, -0.031447, -0.024387, -0.021408, -0.020382, -0.018068, -0.015930, -0.013877, -0.006099, 0.003479, 0.013310, 0.024783, 0.025522, 0.030849, 0.033573, 0.031409, 0.025495, 0.016683, 0.011264, 0.008805, 0.006856, 0.008059, 0.007305, 0.002581, -0.003320, -0.003239, 0.004691, 0.010045
	-0.008791, -0.019334, -0.029149, -0.040533, -0.051698, -0.058235, -0.054863, -0.054840, -0.055692, -0.049534, -0.036731, -0.033053, -0.035667, -0.035315, -0.024352, -0.023825, -0.022538, -0.020438, -0.018207, -0.015389, -0.006515, 0.001966, 0.013591, 0.019434, 0.020600, 0.024967, 0.029425, 0.026812, 0.018980, 0.007878, 0.002360, 0.000859, 0.003849, 0.005649, 0.005421, -0.000416, -0.007906, -0.003164, 0.007582, 0.010039
	-0.018512, -0.018210, -0.033932, -0.050501, -0.061588, -0.064139, -0.060236, -0.062528, -0.067065, -0.062039, -0.045815, -0.039448, -0.040521, -0.042080, -0.033870, -0.030878, -0.027396, -0.024548, -0.021298, -0.020041, -0.011880, -0.002847, 0.008689, 0.015857, 0.015934, 0.018697, 0.022439, 0.022106, 0.017916, 0.005879, 0.001037, -0.001311, -0.001335, 0.001897, 0.003656, 0.000561, -0.006084, -0.005683, 0.000338, 0.006245
	-0.028558, -0.036721, -0.044680, -0.054969, -0.066140, -0.075045, -0.073515, -0.073161, -0.075696, -0.068963, -0.058892, -0.053111, -0.050990, -0.048040, -0.041262, -0.037419, -0.034866, -0.031845, -0.029787, -0.026524, -0.017896, -0.009322, -0.001010, 0.005819, 0.008058, 0.010456, 0.013266, 0.012529, 0.007992, -0.001491, -0.006769, -0.009303, -0.005980, -0.003567, -0.003340, -0.011496, -0.018818, -0.014808, -0.004181, -0.000733
	-0.037253, -0.038393, -0.053129, -0.066170, -0.075959, -0.079233, -0.077475, -0.082688, -0.086779, -0.083983, -0.069005, -0.062542, -0.060351, -0.058481, -0.051101, -0.043149, -0.039837, -0.037039, -0.034698, -0.031301, -0.024330, -0.019786, -0.010285, -0.001967, 0.002812, 0.004899, 0.009657, 0.006946, 0.002155, -0.005232, -0.009851, -0.011218, -0.011509, -0.010097, -0.010293, -0.013175, -0.018958, -0.019846, -0.012107, -0.005641
	-0.046584, -0.055590, -0.062606, -0.069218, -0.080399, -0.087414, -0.089037, -0.092376, -0.095115, -0.088957, -0.080802, -0.073290, -0.068741, -0.064591, -0.054452, -0.048270, -0.045916, -0.044559, -0.042047, -0.039605, -0.032667, -0.025789, -0.019495, -0.012773, -0.006697, -0.003025, 0.001413, 0.000817, -0.004738, -0.013008, -0.017605, -0.018191, -0.018524, -0.016356, -0.016750, -0.021992, -0.028943, -0.025791, -0.016146, -0.010447
	-0.051029, -0.051677, -0.068218, -0.079622, -0.088590, -0.089331, -0.089731, -0.096072, -0.105329, -0.100771, -0.087584, -0.079320, -0.075489, -0.072081, -0.064183, -0.054662, -0.048601, -0.049465, -0.047050, -0.045011, -0.040009, -0.032508, -0.025212, -0.018144, -0.011996, -0.008136, -0.003187, -0.003214, -0.006646, -0.013044, -0.019446, -0.020615, -0.022270, -0.021298, -0.020215, -0.020946, -0.026034, -0.026598, -0.021025, -0.012328
	-0.057184, -0.064908, -0.073093, -0.081584, -0.091971, -0.097048, -0.097688, -0.101869, -0.106651, -0.102162, -0.095658, -0.087938, -0.082718, -0.077017, -0.069608, -0.060682, -0.056889, -0.056864, -0.054260, -0.052011, -0.044563, -0.038927, -0.031943, -0.025832, -0.021170, -0.014319, -0.009046, -0.008543, -0.011751, -0.020287, -0.026608, -0.027259, -0.029120, -0.025549, -0.023221, -0.027725, -0.032477, -0.028427, -0.019343, -0.014932
	-0.060411, -0.062241, -0.080781, -0.090744, -0.100903, -0.099702, -0.098468, -0.104236, -0.116853, -0.112701, -0.102623, -0.095036, -0.091407, -0.089871, -0.079701, -0.070222, -0.064325, -0.063875, -0.062248, -0.059396, -0.052699, -0.047589, -0.041526, -0.028442, -0.024526, -0.019549, -0.015403, -0.014251, -0.017989, -0.022824, -0.027328, -0.029155, -0.033315, -0.032426, -0.027619, -0.030776, -0.033688, -0.032458, -0.027219, -0.019649
	-0.067541, -0.076514, -0.082321, -0.088656, -0.099968, -0.104930, -0.105875, -0.109051, -0.115531, -0.112996, -0.105760, -0.100390, -0.096171, -0.090011, -0.080050, -0.073632, -0.067451, -0.067031, -0.065225, -0.062471, -0.056370, -0.050129, -0.041626, -0.030801, -0.027579, -0.022472, -0.014826, -0.015306, -0.020316, -0.025953, -0.030661, -0.034103, -0.035502, -0.032738, -0.031311, -0.037314, -0.041306, -0.035280, -0.027449, -0.020395
	-0.068162, -0.069269, -0.088235, -0.096809, -0.103385, -0.103271, -0.102507, -0.109535, -0.123412, -0.118580, -0.106622, -0.099580, -0.097644, -0.096978, -0.087259, -0.077196, -0.068978, -0.067016, -0.063682, -0.062548, -0.057901, -0.052295, -0.044088, -0.032703, -0.026551, -0.021607, -0.014155, -0.013747, -0.017390, -0.022419, -0.027444, -0.030877, -0.033450, -0.032423, -0.032041, -0.033598, -0.035149, -0.034054, -0.029356, -0.020998
	-0.069473, -0.075924, -0.083569, -0.089648, -0.101235, -0.105828, -0.109144, -0.112613, -0.117233, -0.114186, -0.107090, -0.098616, -0.097084, -0.094257, -0.086773, -0.076409, -0.069532, -0.066472, -0.060956, -0.059191, -0.052886, -0.047752, -0.041275, -0.032437, -0.027780, -0.020398, -0.012061, -0.010133, -0.014056, -0.021528, -0.027924, -0.030605, -0.030609, -0.026068, -0.029346, -0.033991, -0.038254, -0.030610, -0.021109, -0.015885
	-0.068084, -0.066409, -0.083944, -0.094013, -0.102504, -0.105274, -0.106036, -0.112090, -0.121664, -0.117824, -0.104850, -0.097467, -0.098833, -0.098622, -0.089603, -0.078147, -0.068143, -0.066300, -0.061573, -0.057727, -0.054825, -0.048625, -0.040164, -0.030532, -0.025948, -0.020264, -0.014196, -0.010702, -0.013794, -0.019775, -0.026095, -0.028838, -0.030254, -0.027944, -0.027980, -0.030915, -0.032446, -0.028861, -0.023732, -0.014676
	-0.065280, -0.068669, -0.076948, -0.082397, -0.094986, -0.105117, -0.107099, -0.108954, -0.112557, -0.110326, -0.100725, -0.096325, -0.096240, -0.092388, -0.081185, -0.071682, -0.065650, -0.062250, -0.057027, -0.054691, -0.048349, -0.042069, -0.032712, -0.027728, -0.023396, -0.018458, -0.008357, -0.005699, -0.011447, -0.020033, -0.026387, -0.030280, -0.028443, -0.023735, -0.023838, -0.031580, -0.034204, -0.027768, -0.018029, -0.010628
	-0.061662, -0.057052, -0.075163, -0.086710, -0.094182, -0.097544, -0.098814, -0.105908, -0.114460, -0.111718, -0.097559, -0.091614, -0.093860, -0.093098, -0.081687, -0.069410, -0.064117, -0.062745, -0.055603, -0.051413, -0.048043, -0.040363, -0.031842, -0.023420, -0.017470, -0.012600, -0.008163, -0.003898, -0.007635, -0.013254, -0.019807, -0.025153, -0.027074, -0.023513, -0.023727, -0.028669, -0.029153, -0.024831, -0.018735, -0.009246
	-0.056176, -0.059439, -0.066501, -0.071527, -0.085216, -0.094918, -0.097595, -0.099419, -0.101847, -0.102015, -0.093849, -0.089867, -0.088840, -0.083167, -0.071832, -0.062522, -0.058023, -0.057771, -0.053050, -0.048285, -0.041374, -0.033527, -0.024473, -0.018428, -0.013958, -0.008161, -0.001196, 0.001754, -0.004016, -0.011132, -0.018325, -0.021813, -0.021514, -0.016948, -0.018061, -0.025702, -0.028671, -0.021470, -0.011028, -0.001934
	-0.059202, -0.050525, -0.065461, -0.076792, -0.084156, -0.088538, -0.090719, -0.096070, -0.105729, -0.105136, -0.090350, -0.083865, -0.087807, -0.086145, -0.074773, -0.064235, -0.057641, -0.055896, -0.051286, -0.046566, -0.042431, -0.034723, -0.023762, -0.014983, -0.009126, -0.004877, 0.000094, 0.003492, -0.000931, -0.005883, -0.011665, -0.015251, -0.016432, -0.016119, -0.015373, -0.018827, -0.019994, -0.017564, -0.012298, 0.002094
	-0.055561, -0.058184, -0.062669, -0.068111, -0.080741, -0.091895, -0.093911, -0.094387, -0.100239, -0.100695, -0.089841, -0.085682, -0.085212, -0.082910, -0.073072, -0.063594, -0.056157, -0.053482, -0.048107, -0.045405, -0.039982, -0.029777, -0.019905, -0.013872, -0.009732, -0.004272, 0.003500, 0.006909, 0.001302, -0.004626, -0.012374, -0.014751, -0.014637, -0.011794, -0.012913, -0.018244, -0.023377, -0.018086, -0.006575, 0.003294
	-0.062834, -0.047300, -0.060870, -0.073023, -0.079303, -0.082121, -0.083623, -0.091321, -0.100996, -0.098896, -0.085406, -0.078881, -0.081932, -0.082077, -0.074409, -0.063158, -0.053822, -0.050328, -0.045077, -0.039678, -0.035825, -0.028532, -0.017793, -0.009121, -0.003444, -0.000905, 0.003990, 0.007745, 0.004595, 0.000143, -0.004555, -0.007411, -0.010850, -0.010100, -0.010079, -0.013177, -0.016434, -0.014663, -0.010248, -0.000213
	-0.054748, -0.053907, -0.057576, -0.063118, -0.072478, -0.081366, -0.084424, -0.086348, -0.089718, -0.089305, -0.081771, -0.076889, -0.076923, -0.073518, -0.067973, -0.057643, -0.050848, -0.046966, -0.041560, -0.036436, -0.029233, -0.020685, -0.010240, -0.004935, -0.001084, 0.002478, 0.009168, 0.014038, 0.010885, 0.004752, -0.001650, -0.004209, -0.003998, -0.002336, -0.003784, -0.010930, -0.016480, -0.012798, -0.003650, 0.002998
	-0.059345, -0.041989, -0.057435, -0.068229, -0.072857, -0.072586, -0.075155, -0.083286, -0.091292, -0.089727, -0.073702, -0.068353, -0.072910, -0.073863, -0.065527, -0.053635, -0.046064, -0.043899, -0.037607, -0.031251, -0.026194, -0.018885, -0.008095, 0.000309, 0.004911, 0.007046, 0.010642, 0.015635, 0.015277, 0.012612, 0.008074, 0.004852, 0.001546, 0.000504, 0.000589, -0.002769, -0.006432, -0.007765, -0.005391, 0.006950
	-0.050324, -0.049088, -0.052417, -0.057257, -0.063818, -0.071057, -0.074636, -0.075459, -0.079445, -0.077368, -0.068788, -0.063940, -0.065040, -0.063419, -0.054864, -0.044910, -0.038774, -0.036951, -0.031149, -0.026080, -0.018383, -0.011985, -0.001732, 0.003893, 0.007180, 0.011120, 0.017429, 0.021738, 0.019167, 0.015812, 0.011027, 0.007243, 0.006720, 0.009346, 0.006598, -0.003776, -0.009199, -0.007592, 0.005481, 0.014396
	-0.058437, -0.035937, -0.050762, -0.060425, -0.061123, -0.059090, -0.062399, -0.072124, -0.080338, -0.074950, -0.060985, -0.054754, -0.059333, -0.060500, -0.051714, -0.038834, -0.031117, -0.031693, -0.025186, -0.017982, -0.014316, -0.010137, 0.000228, 0.008774, 0.014018, 0.016470, 0.019918, 0.022071, 0.021109, 0.019957, 0.018698, 0.015803, 0.013135, 0.011136, 0.008719, 0.003522, -0.000994, 0.000525, 0.006297, 0.018454
	-0.046143, -0.041577, -0.045391, -0.046668, -0.051722, -0.057607, -0.062802, -0.065205, -0.068243, -0.066293, -0.058216, -0.051324, -0.051806, -0.051018, -0.043393, -0.032431, -0.024016, -0.023321, -0.018504, -0.013897, -0.008455, -0.001123, 0.006609, 0.010462, 0.013887, 0.019328, 0.024804, 0.026590, 0.023420, 0.020337, 0.017129, 0.017199, 0.016391, 0.015616, 0.013257, 0.005832, -0.000019, 0.003462, 0.014308, 0.023624
	-0.051989, -0.030294, -0.043380, -0.051339, -0.050711, -0.048193, -0.052258, -0.061218, -0.070507, -0.068810, -0.049476, -0.042352, -0.046018, -0.046673, -0.038670, -0.027263, -0.018137, -0.018587, -0.013603, -0.008482, -0.004647, -0.000011, 0.008230, 0.015652, 0.019436, 0.023069, 0.024762, 0.027750, 0.028115, 0.026227, 0.022220, 0.023166, 0.020341, 0.018455, 0.014918, 0.011932, 0.007138, 0.008523, 0.014718, 0.026201
	-0.041448, -0.035286, -0.036538, -0.037577, -0.044652, -0.049300, -0.051092, -0.052841, -0.058068, -0.056947, -0.046235, -0.038436, -0.037494, -0.034175, -0.028932, -0.016904, -0.010075, -0.010552, -0.004464, -0.001243, 0.003236, 0.010200, 0.015604, 0.020362, 0.023157, 0.028023, 0.032826, 0.035958, 0.034819, 0.030600, 0.025988, 0.026013, 0.026284, 0.025661, 0.022322, 0.013336, 0.006464, 0.011312, 0.022330, 0.031668
	-0.048540, -0.022534, -0.035260, -0.042156, -0.042749, -0.037408, -0.038818, -0.047322, -0.056808, -0.053643, -0.035691, -0.027822, -0.028789, -0.028255, -0.020274, -0.007285, -0.000723, -0.000788, 0.005440, 0.008938, 0.008953, 0.012074, 0.017957, 0.025241, 0.029175, 0.032057, 0.033733, 0.038359, 0.039349, 0.037161, 0.034052, 0.034585, 0.032020, 0.029940, 0.026326, 0.024577, 0.020432, 0.021586, 0.024568, 0.034552
	-0.033086, -0.027982, -0.029443, -0.029011, -0.035629, -0.040579, -0.038290, -0.037389, -0.041260, -0.040430, -0.032279, -0.021394, -0.018817, -0.015525, -0.007558, 0.006345, 0.011048, 0.011271, 0.013497, 0.017030, 0.017449, 0.022752, 0.026764, 0.030722, 0.033532, 0.037203, 0.043356, 0.048536, 0.047776, 0.043851, 0.039311, 0.039944, 0.039954, 0.038931, 0.034893, 0.030946, 0.023127, 0.027359, 0.034859, 0.043920
	-0.036218, -0.016846, -0.030897, -0.036980, -0.037261, -0.033334, -0.030888, -0.034074, -0.042142, -0.039980, -0.021377, -0.013603, -0.014171, -0.013131, -0.001768, 0.014998, 0.020060, 0.018173, 0.019934, 0.024704, 0.023739, 0.024617, 0.027288, 0.035116, 0.041187, 0.043128, 0.045921, 0.051709, 0.053031, 0.050698, 0.047697, 0.047728, 0.046845, 0.043201, 0.041805, 0.040728, 0.036184, 0.034435, 0.035120, 0.045329
	-0.029808, -0.023871, -0.026541, -0.026705, -0.031203, -0.036908, -0.034411, -0.029231, -0.028090, -0.026102, -0.016691, -0.007747, -0.004471, 0.001560, 0.010738, 0.025062, 0.027672, 0.024833, 0.026976, 0.029502, 0.030754, 0.035709, 0.039403, 0.044719, 0.046379, 0.049250, 0.054178, 0.059793, 0.059542, 0.052111, 0.047608, 0.050103, 0.053142, 0.052747, 0.050045, 0.044102, 0.033149, 0.035392, 0.045678, 0.054080
	-0.032238, -0.008993, -0.023999, -0.030969, -0.028658, -0.024887, -0.024493, -0.028088, -0.031053, -0.022849, -0.003868, 0.004647, 0.004540, 0.007560, 0.018373, 0.031401, 0.035778, 0.033768, 0.035173, 0.035884, 0.036597, 0.038940, 0.044566, 0.053914, 0.056554, 0.056382, 0.056449, 0.060387, 0.062696, 0.058223, 0.055016, 0.056193, 0.056891, 0.052793, 0.052741, 0.052626, 0.048117, 0.045032, 0.048033, 0.055100
	-0.019758, -0.015110, -0.017814, -0.018871, -0.023340, -0.028653, -0.026880, -0.018681, -0.017020, -0.011343, -0.001002, 0.008249, 0.014012, 0.020367, 0.026878, 0.038534, 0.041827, 0.039532, 0.039775, 0.039109, 0.043172, 0.049325, 0.056604, 0.059583, 0.059329, 0.059876, 0.062766, 0.068759, 0.067214, 0.059657, 0.055950, 0.056798, 0.058619, 0.058591, 0.059849, 0.056473, 0.046841, 0.047921, 0.058342, 0.065346
	-0.018628, -0.000296, -0.014764, -0.022634, -0.020483, -0.016362, -0.015485, -0.017352, -0.020246, -0.010362, 0.008635, 0.018414, 0.018542, 0.024258, 0.033370, 0.045728, 0.049983, 0.044610, 0.044638, 0.047649, 0.049220, 0.051954, 0.058932, 0.065915, 0.069102, 0.067410, 0.067680, 0.073734, 0.072203, 0.067293, 0.063945, 0.064378, 0.065047, 0.061989, 0.062882, 0.063468, 0.059707, 0.057986, 0.059739, 0.066139
	-0.010091, -0.006551, -0.008018, -0.009589, -0.016068, -0.020662, -0.019451, -0.010985, -0.009391, -0.003580, 0.007826, 0.019598, 0.024961, 0.033762, 0.040618, 0.050868, 0.052139, 0.050495, 0.049198, 0.051777, 0.056840, 0.061771, 0.068414, 0.072295, 0.073443, 0.072145, 0.073414, 0.079338, 0.075988, 0.067367, 0.064745, 0.064435, 0.066982, 0.065811, 0.067424, 0.063230, 0.058438, 0.059982, 0.067672, 0.072460
	-0.016254, 0.006291, -0.008031, -0.013944, -0.014475, -0.010741, -0.009932, -0.011709, -0.015503, -0.006971, 0.013190, 0.024865, 0.029121, 0.033942, 0.044335, 0.054572, 0.058078, 0.055224, 0.055897, 0.058327, 0.061207, 0.063939, 0.070506, 0.078141, 0.084203, 0.081223, 0.079519, 0.082883, 0.080890, 0.076174, 0.071279, 0.073064, 0.071225, 0.066859, 0.069860, 0.070836, 0.069427, 0.069140, 0.070950, 0.075269
	-0.008127, 0.000730, 0.001164, -0.000308, -0.006659, -0.012343, -0.011463, -0.003755, -0.001876, 0.005166, 0.016616, 0.030243, 0.036509, 0.045020, 0.053681, 0.063738, 0.066425, 0.063964, 0.062796, 0.065633, 0.071912, 0.077280, 0.082580, 0.086477, 0.089798, 0.089603, 0.091453, 0.096125, 0.088708, 0.079903, 0.074317, 0.076190, 0.075399, 0.075242, 0.079628, 0.077855, 0.071473, 0.073702, 0.082757, 0.088086
	-0.010951, 0.013218, -0.000878, -0.006241, -0.005623, 0.000046, 0.000158, -0.002943, -0.005314, 0.005491, 0.026890, 0.035754, 0.041490, 0.045829, 0.059325, 0.070249, 0.074114, 0.071815, 0.073229, 0.076313, 0.080778, 0.081554, 0.087919, 0.096206, 0.101562, 0.101674, 0.100494, 0.103989, 0.100292, 0.093977, 0.088080, 0.088136, 0.086555, 0.081494, 0.084966, 0.087073, 0.084113, 0.085184, 0.087700, 0.092188
	-0.002972, 0.006020, 0.006098, 0.004303, 0.001326, -0.002386, -0.001840, 0.005325, 0.008624, 0.016246, 0.026781, 0.039696, 0.048540, 0.055938, 0.066982, 0.076497, 0.080828, 0.079669, 0.080127, 0.083754, 0.089783, 0.093456, 0.100570, 0.105322, 0.107132, 0.110571, 0.113141, 0.118064, 0.111721, 0.101634, 0.093555, 0.093112, 0.093104, 0.092325, 0.094780, 0.092552, 0.085283, 0.088882, 0.097508, 0.105280
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 11.4
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Preperations]
version = 1
points = 
	0.012158, -0.006098, -0.020628, -0.034069, -0.049418, -0.058491, -0.062706, -0.063181, -0.065552, -0.063461, -0.057373, -0.056717, -0.056579, -0.054080, -0.053373, -0.056878, -0.057281, -0.055224, -0.049676, -0.047605, -0.041454, -0.034605, -0.022490, -0.011292, -0.009411, -0.005344, -0.003510, -0.002717, -0.005999, -0.010712, -0.013141, -0.015611, -0.020004, -0.017667, -0.016629, -0.022248, -0.024864, -0.024065, -0.014921, -0.010826
	-0.005958, -0.021084, -0.033800, -0.047903, -0.059950, -0.071345, -0.072502, -0.073350, -0.075852, -0.072963, -0.067236, -0.064315, -0.065698, -0.064338, -0.062871, -0.065238, -0.067095, -0.063584, -0.059241, -0.057846, -0.051380, -0.043157, -0.030230, -0.019950, -0.018121, -0.014291, -0.009354, -0.013065, -0.016464, -0.022925, -0.025337, -0.026541, -0.030577, -0.029068, -0.027094, -0.030532, -0.034241, -0.032625, -0.021498, -0.020513
	-0.017526, -0.027763, -0.040710, -0.055305, -0.068172, -0.079641, -0.081247, -0.081903, -0.083679, -0.081855, -0.073270, -0.070340, -0.072083, -0.071536, -0.066055, -0.065901, -0.069085, -0.066531, -0.063284, -0.061616, -0.053366, -0.047292, -0.035451, -0.023167, -0.022205, -0.016699, -0.012552, -0.014153, -0.018802, -0.030443, -0.032210, -0.034051, -0.034437, -0.031439, -0.030406, -0.032817, -0.036351, -0.034849, -0.024250, -0.019489
	-0.017750, -0.030284, -0.043463, -0.055839, -0.071865, -0.084888, -0.086157, -0.084619, -0.086681, -0.084515, -0.075246, -0.073263, -0.075604, -0.075123, -0.069177, -0.070723, -0.071097, -0.068644, -0.065465, -0.063718, -0.057574, -0.049335, -0.036556, -0.028418, -0.028259, -0.023387, -0.018454, -0.020519, -0.027499, -0.038314, -0.041534, -0.041886, -0.039972, -0.036438, -0.033959, -0.033009, -0.038291, -0.036339, -0.022688, -0.024783
	-0.021354, -0.034103, -0.047541, -0.060551, -0.075691, -0.089373, -0.092241, -0.091621, -0.093203, -0.090723, -0.082480, -0.079781, -0.079706, -0.079674, -0.074365, -0.073780, -0.073465, -0.070165, -0.064970, -0.065503, -0.059104, -0.051038, -0.041817, -0.031243, -0.031386, -0.028837, -0.023658, -0.024237, -0.029641, -0.039210, -0.042766, -0.044461, -0.041863, -0.039075, -0.034881, -0.034571, -0.039386, -0.038253, -0.031659, -0.024202
	-0.027696, -0.041184, -0.054054, -0.064759, -0.080898, -0.094964, -0.097906, -0.098033, -0.101256, -0.098300, -0.091517, -0.088420, -0.086945, -0.085220, -0.079938, -0.079979, -0.079828, -0.074842, -0.072903, -0.072415, -0.065384, -0.057454, -0.048482, -0.040977, -0.039336, -0.036065, -0.032553, -0.034336, -0.039337, -0.046271, -0.049398, -0.051220, -0.049530, -0.045000, -0.045029, -0.042100, -0.049767, -0.046386, -0.035574, -0.032188
	-0.033426, -0.046259, -0.059363, -0.068024, -0.084858, -0.097009, -0.103434, -0.106215, -0.107319, -0.106178, -0.100333, -0.097536, -0.095352, -0.091322, -0.086332, -0.082309, -0.081440, -0.078413, -0.075067, -0.073134, -0.068255, -0.062667, -0.054300, -0.046004, -0.042001, -0.039181, -0.035010, -0.036092, -0.041599, -0.048788, -0.051751, -0.051179, -0.051019, -0.049121, -0.045860, -0.046756, -0.050005, -0.051613, -0.040237, -0.035349
	-0.037931, -0.051993, -0.066455, -0.075044, -0.088177, -0.102890, -0.108223, -0.112373, -0.115787, -0.113421, -0.108543, -0.105936, -0.101048, -0.096863, -0.090726, -0.087882, -0.086665, -0.083874, -0.081096, -0.080894, -0.075125, -0.071038, -0.063072, -0.054696, -0.051039, -0.046728, -0.042566, -0.043887, -0.048745, -0.056834, -0.059808, -0.060521, -0.060664, -0.057968, -0.056317, -0.052477, -0.058814, -0.055877, -0.046325, -0.042545
	-0.041429, -0.053634, -0.067633, -0.077111, -0.090998, -0.103561, -0.109445, -0.114741, -0.120075, -0.119821, -0.114703, -0.110411, -0.105589, -0.099826, -0.093730, -0.089705, -0.087199, -0.086439, -0.082688, -0.082221, -0.078348, -0.073203, -0.065273, -0.058731, -0.054025, -0.049231, -0.044830, -0.043830, -0.045839, -0.054137, -0.059075, -0.059515, -0.058546, -0.056956, -0.054145, -0.053129, -0.056587, -0.056341, -0.047057, -0.039936
	-0.044295, -0.058972, -0.072101, -0.082726, -0.095001, -0.106449, -0.111505, -0.118363, -0.124608, -0.123506, -0.120263, -0.115400, -0.110227, -0.104535, -0.100348, -0.095757, -0.092961, -0.092377, -0.089613, -0.088047, -0.084834, -0.079314, -0.072500, -0.064519, -0.060449, -0.055767, -0.051803, -0.050997, -0.052855, -0.058115, -0.063348, -0.065363, -0.067936, -0.063474, -0.061475, -0.054726, -0.062529, -0.055352, -0.048878, -0.044991
	-0.045804, -0.056574, -0.073308, -0.082450, -0.097495, -0.107467, -0.111501, -0.116418, -0.126724, -0.125980, -0.123231, -0.120494, -0.114667, -0.111289, -0.103451, -0.099228, -0.095880, -0.095882, -0.093328, -0.091000, -0.087051, -0.081909, -0.075949, -0.064971, -0.061050, -0.055137, -0.049046, -0.047319, -0.049806, -0.056968, -0.059608, -0.060249, -0.063032, -0.060556, -0.056284, -0.056263, -0.058891, -0.057890, -0.051554, -0.042382
	-0.049818, -0.062681, -0.076305, -0.084328, -0.098717, -0.107866, -0.113937, -0.120088, -0.128622, -0.128931, -0.126353, -0.123191, -0.118529, -0.115642, -0.106288, -0.103976, -0.099708, -0.097750, -0.094501, -0.094545, -0.090910, -0.085952, -0.077352, -0.067196, -0.062435, -0.057738, -0.052934, -0.051098, -0.055294, -0.061112, -0.063120, -0.067525, -0.067979, -0.066558, -0.064608, -0.060597, -0.067812, -0.057641, -0.056224, -0.046471
	-0.050591, -0.060432, -0.075602, -0.083877, -0.096933, -0.106147, -0.112334, -0.118295, -0.127966, -0.128757, -0.125157, -0.121831, -0.118557, -0.116124, -0.108723, -0.104502, -0.099469, -0.095841, -0.090662, -0.089822, -0.087969, -0.084545, -0.076375, -0.064821, -0.059093, -0.053427, -0.047372, -0.044341, -0.047964, -0.054064, -0.057133, -0.059152, -0.061568, -0.059109, -0.056640, -0.056691, -0.056844, -0.054564, -0.048514, -0.040641
	-0.047704, -0.059564, -0.073127, -0.080945, -0.093764, -0.105483, -0.111501, -0.118792, -0.124812, -0.126576, -0.122064, -0.118087, -0.116126, -0.114867, -0.108053, -0.103336, -0.097558, -0.093250, -0.086537, -0.085303, -0.083677, -0.079292, -0.070542, -0.062526, -0.056818, -0.052534, -0.044035, -0.041353, -0.046942, -0.051329, -0.055481, -0.062777, -0.058499, -0.058025, -0.057390, -0.053562, -0.060843, -0.046555, -0.046260, -0.036083
	-0.046496, -0.052983, -0.067518, -0.076904, -0.091704, -0.103105, -0.111995, -0.117751, -0.122307, -0.122941, -0.118230, -0.115004, -0.114258, -0.113138, -0.105515, -0.098417, -0.093384, -0.090070, -0.083281, -0.079846, -0.078725, -0.075452, -0.066225, -0.057269, -0.053103, -0.047808, -0.039772, -0.036834, -0.041270, -0.047376, -0.051111, -0.053848, -0.053029, -0.050301, -0.048919, -0.050775, -0.050121, -0.046842, -0.039633, -0.030497
	-0.040695, -0.051685, -0.064038, -0.070974, -0.086679, -0.101773, -0.109889, -0.114373, -0.117883, -0.118764, -0.113125, -0.110931, -0.111099, -0.109664, -0.098733, -0.093182, -0.090154, -0.086213, -0.077214, -0.077108, -0.075555, -0.069117, -0.060704, -0.054093, -0.049253, -0.044799, -0.037536, -0.035304, -0.040134, -0.045456, -0.051720, -0.056675, -0.053743, -0.052923, -0.049701, -0.050238, -0.056776, -0.041485, -0.041755, -0.027329
	-0.039842, -0.039428, -0.055732, -0.063890, -0.079179, -0.092823, -0.101698, -0.106156, -0.111709, -0.113152, -0.108033, -0.104872, -0.105645, -0.103501, -0.094487, -0.087264, -0.084273, -0.080950, -0.074116, -0.070973, -0.068409, -0.062825, -0.054757, -0.044150, -0.040620, -0.036602, -0.031538, -0.026478, -0.031123, -0.037600, -0.042341, -0.046700, -0.047380, -0.042880, -0.040967, -0.045367, -0.044192, -0.038553, -0.029948, -0.020790
	-0.030596, -0.038279, -0.051528, -0.058981, -0.073983, -0.089044, -0.099173, -0.101740, -0.104830, -0.107083, -0.102306, -0.101554, -0.101336, -0.097146, -0.089217, -0.083800, -0.080621, -0.078071, -0.071535, -0.068328, -0.065806, -0.056882, -0.048683, -0.039756, -0.036349, -0.031328, -0.025351, -0.024133, -0.029773, -0.033858, -0.040011, -0.044146, -0.043900, -0.044797, -0.038019, -0.042319, -0.047297, -0.031851, -0.034318, -0.013527
	-0.032121, -0.034722, -0.047839, -0.054710, -0.069175, -0.084213, -0.094533, -0.097233, -0.100863, -0.104775, -0.099781, -0.097416, -0.098804, -0.096059, -0.086694, -0.079692, -0.076749, -0.074609, -0.068106, -0.063906, -0.061136, -0.055447, -0.045559, -0.035389, -0.029696, -0.025708, -0.020034, -0.017335, -0.022665, -0.028532, -0.032369, -0.035760, -0.037212, -0.035201, -0.032872, -0.034132, -0.035907, -0.032127, -0.025026, -0.009282
	-0.026707, -0.034374, -0.045183, -0.052691, -0.067014, -0.084964, -0.092286, -0.094441, -0.099291, -0.103609, -0.098278, -0.094972, -0.097169, -0.095394, -0.086653, -0.080205, -0.076284, -0.070594, -0.064535, -0.062012, -0.060174, -0.051216, -0.040622, -0.033396, -0.029636, -0.024235, -0.017274, -0.018232, -0.021459, -0.024778, -0.031754, -0.034481, -0.033398, -0.037949, -0.030432, -0.033219, -0.038432, -0.021975, -0.030052, -0.009295
	-0.028559, -0.029280, -0.042071, -0.048655, -0.061603, -0.076257, -0.086817, -0.091815, -0.095682, -0.098682, -0.093729, -0.091168, -0.092213, -0.090073, -0.084070, -0.077048, -0.072045, -0.066267, -0.060309, -0.053639, -0.051696, -0.046852, -0.034069, -0.025602, -0.020640, -0.018021, -0.013180, -0.009049, -0.013846, -0.018012, -0.021061, -0.024515, -0.027068, -0.026804, -0.024283, -0.025595, -0.028234, -0.025272, -0.019246, -0.008595
	-0.025711, -0.029003, -0.038836, -0.048015, -0.058511, -0.074480, -0.083738, -0.087945, -0.091439, -0.094310, -0.090288, -0.087858, -0.088589, -0.086163, -0.081829, -0.075146, -0.071136, -0.064399, -0.057338, -0.052103, -0.049650, -0.043210, -0.032998, -0.023124, -0.020191, -0.016625, -0.012433, -0.010465, -0.009871, -0.015007, -0.021217, -0.021582, -0.023800, -0.027652, -0.021527, -0.027137, -0.030828, -0.020152, -0.026202, -0.008568
	-0.031287, -0.022523, -0.035800, -0.041583, -0.052691, -0.065901, -0.075941, -0.079246, -0.083936, -0.086778, -0.082235, -0.078893, -0.080642, -0.079419, -0.074324, -0.067418, -0.062113, -0.057744, -0.049923, -0.043390, -0.040055, -0.035512, -0.023838, -0.015485, -0.009895, -0.008346, -0.005387, 0.001467, -0.000104, -0.003777, -0.007926, -0.012023, -0.013970, -0.014207, -0.013994, -0.017009, -0.019233, -0.019282, -0.014210, -0.001146
	-0.020719, -0.024043, -0.035160, -0.041635, -0.051902, -0.063884, -0.072884, -0.076738, -0.081856, -0.083761, -0.077857, -0.074651, -0.077952, -0.076310, -0.069721, -0.063240, -0.056775, -0.055188, -0.046711, -0.042996, -0.039499, -0.032268, -0.023129, -0.015735, -0.012305, -0.009383, -0.005789, -0.001996, -0.001166, -0.005106, -0.009634, -0.009864, -0.011905, -0.015913, -0.010246, -0.016645, -0.022975, -0.011972, -0.018524, 0.001048
	-0.026050, -0.019774, -0.032555, -0.037813, -0.044657, -0.054435, -0.065271, -0.071019, -0.075585, -0.077479, -0.072635, -0.069526, -0.071046, -0.070770, -0.063085, -0.055960, -0.050956, -0.049593, -0.042773, -0.034996, -0.032645, -0.029030, -0.020343, -0.011008, -0.005751, -0.003252, 0.000746, 0.003215, 0.001749, -0.000068, -0.001413, -0.002608, -0.005837, -0.007103, -0.008431, -0.012027, -0.015656, -0.014417, -0.006321, 0.003748
	-0.021728, -0.019178, -0.031232, -0.036249, -0.042206, -0.053190, -0.064017, -0.068545, -0.074597, -0.074544, -0.069543, -0.065779, -0.067928, -0.067354, -0.060655, -0.052790, -0.047723, -0.046044, -0.038188, -0.034539, -0.032080, -0.027152, -0.018902, -0.012508, -0.009304, -0.003955, -0.000288, -0.001549, -0.000556, -0.003756, -0.008467, -0.003851, -0.005999, -0.012959, -0.007423, -0.015332, -0.017388, -0.005695, -0.010807, 0.007710
	-0.028204, -0.017096, -0.027984, -0.032129, -0.038374, -0.046561, -0.059356, -0.061847, -0.069228, -0.070551, -0.065474, -0.059719, -0.059893, -0.060271, -0.053666, -0.047202, -0.041189, -0.039979, -0.033189, -0.028761, -0.025714, -0.021660, -0.014905, -0.007841, -0.004669, -0.001174, 0.001874, 0.005613, 0.005527, 0.001504, -0.000694, 0.001892, 0.001885, -0.002506, -0.005619, -0.007166, -0.009935, -0.007406, 0.000545, 0.009983
	-0.019393, -0.017785, -0.025482, -0.028146, -0.036861, -0.047528, -0.055696, -0.059118, -0.064151, -0.066346, -0.060565, -0.055661, -0.055495, -0.051944, -0.048147, -0.040645, -0.036359, -0.035990, -0.026764, -0.024843, -0.023572, -0.019648, -0.013807, -0.006811, -0.004589, -0.000266, 0.003010, 0.004931, 0.006834, 0.003254, -0.001690, 0.003120, 0.001036, -0.005283, 0.000659, -0.007399, -0.010996, -0.000832, -0.006381, 0.012135
	-0.021519, -0.010062, -0.018662, -0.023011, -0.029067, -0.036961, -0.043194, -0.048197, -0.053632, -0.055489, -0.050054, -0.045247, -0.042655, -0.040243, -0.034315, -0.027094, -0.022697, -0.021644, -0.015333, -0.010768, -0.013712, -0.012051, -0.005326, 0.000560, 0.005300, 0.007429, 0.009930, 0.015968, 0.016454, 0.012383, 0.010385, 0.011612, 0.011413, 0.008357, 0.006831, 0.005524, 0.003087, 0.003507, 0.009876, 0.018892
	-0.017331, -0.015238, -0.021971, -0.024651, -0.029507, -0.040209, -0.044232, -0.046101, -0.052689, -0.053151, -0.047133, -0.042985, -0.040475, -0.037020, -0.029999, -0.021348, -0.018232, -0.017876, -0.013058, -0.008535, -0.013279, -0.011527, -0.006296, -0.001615, 0.002270, 0.006991, 0.010272, 0.013407, 0.015950, 0.012503, 0.008026, 0.013701, 0.011513, 0.004867, 0.010667, 0.006774, 0.003571, 0.012416, 0.004875, 0.020961
	-0.022637, -0.011107, -0.018340, -0.023896, -0.028320, -0.038092, -0.041212, -0.041642, -0.044537, -0.046015, -0.041699, -0.035805, -0.033527, -0.030911, -0.022925, -0.010175, -0.007279, -0.008644, -0.005065, -0.000597, -0.003797, -0.004052, 0.000635, 0.006175, 0.010857, 0.012993, 0.016956, 0.022765, 0.023298, 0.020262, 0.018285, 0.019467, 0.021161, 0.018785, 0.017891, 0.017817, 0.013874, 0.012825, 0.015904, 0.025844
	-0.014532, -0.010189, -0.019385, -0.022584, -0.028159, -0.037803, -0.040566, -0.038125, -0.040339, -0.038899, -0.033171, -0.028143, -0.025641, -0.019755, -0.012463, -0.003824, -0.000871, -0.002698, -0.000197, 0.001952, -0.001353, -0.000188, 0.004902, 0.012600, 0.014373, 0.016449, 0.018872, 0.022822, 0.026385, 0.020681, 0.015275, 0.021387, 0.023535, 0.016733, 0.022161, 0.018819, 0.011276, 0.020785, 0.014683, 0.032409
	-0.016972, -0.004835, -0.015539, -0.019706, -0.022971, -0.032222, -0.037732, -0.035551, -0.033892, -0.031679, -0.024624, -0.019946, -0.016412, -0.010040, -0.003445, 0.005991, 0.008364, 0.006410, 0.008289, 0.009260, 0.007409, 0.008691, 0.015230, 0.022729, 0.025465, 0.025502, 0.026102, 0.030309, 0.031861, 0.026963, 0.024651, 0.027000, 0.029039, 0.025577, 0.027217, 0.027660, 0.023245, 0.021705, 0.026383, 0.034120
	-0.007042, -0.003943, -0.013314, -0.016082, -0.020497, -0.030911, -0.035096, -0.030889, -0.029351, -0.025337, -0.018980, -0.012449, -0.008879, -0.001902, 0.003577, 0.011256, 0.012460, 0.010502, 0.011904, 0.011483, 0.010067, 0.013356, 0.020792, 0.027368, 0.026382, 0.028554, 0.028164, 0.029993, 0.033232, 0.028830, 0.022354, 0.027991, 0.029607, 0.020011, 0.031066, 0.031755, 0.025061, 0.037228, 0.024607, 0.041453
	-0.012463, -0.000987, -0.008994, -0.014815, -0.017487, -0.026372, -0.031392, -0.028459, -0.025402, -0.024153, -0.015566, -0.007862, -0.004579, 0.001484, 0.010757, 0.017401, 0.019536, 0.016264, 0.016278, 0.018231, 0.018193, 0.018217, 0.025442, 0.034794, 0.036179, 0.034770, 0.033985, 0.040104, 0.040404, 0.034161, 0.030977, 0.032380, 0.034144, 0.031909, 0.033231, 0.035957, 0.034171, 0.033050, 0.038776, 0.042972
	-0.002758, 0.000700, -0.008467, -0.011525, -0.018705, -0.027522, -0.031609, -0.027494, -0.026315, -0.023221, -0.014164, -0.006562, -0.002205, 0.006453, 0.013689, 0.018647, 0.017673, 0.016751, 0.017380, 0.018782, 0.019038, 0.021992, 0.027475, 0.034748, 0.036870, 0.036635, 0.035394, 0.037519, 0.038008, 0.032063, 0.025834, 0.030409, 0.033142, 0.023991, 0.034882, 0.034323, 0.030317, 0.042711, 0.030793, 0.045129
	-0.011501, 0.004979, -0.003199, -0.009532, -0.013737, -0.022490, -0.028056, -0.025047, -0.023987, -0.021727, -0.011113, -0.003633, 0.003070, 0.010580, 0.020230, 0.025058, 0.026653, 0.024592, 0.024567, 0.025613, 0.027386, 0.029282, 0.037705, 0.042901, 0.046601, 0.045443, 0.044217, 0.048155, 0.045715, 0.039788, 0.034981, 0.038594, 0.038594, 0.034532, 0.038671, 0.042065, 0.040659, 0.042101, 0.045919, 0.050030
	-0.005239, 0.006624, -0.001837, -0.005350, -0.012024, -0.022230, -0.026144, -0.022704, -0.021559, -0.017450, -0.008515, 0.000433, 0.007392, 0.014546, 0.023538, 0.029043, 0.029892, 0.027280, 0.028785, 0.030662, 0.032758, 0.032649, 0.040035, 0.046372, 0.048654, 0.050330, 0.049538, 0.049746, 0.048851, 0.041068, 0.034598, 0.041375, 0.041379, 0.030621, 0.043091, 0.044712, 0.038634, 0.053475, 0.042814, 0.059369
	-0.011843, 0.005417, 0.000007, -0.005709, -0.011391, -0.019100, -0.024151, -0.021274, -0.019356, -0.016953, -0.004422, 0.002891, 0.010688, 0.018353, 0.027665, 0.035281, 0.036655, 0.034937, 0.036795, 0.039994, 0.042705, 0.042668, 0.048600, 0.055673, 0.059602, 0.061002, 0.059934, 0.064283, 0.061835, 0.052838, 0.048644, 0.048401, 0.048158, 0.044262, 0.049173, 0.053313, 0.050054, 0.051718, 0.058112, 0.062677
	-0.003249, 0.007140, -0.000190, -0.005182, -0.010664, -0.017472, -0.021072, -0.018928, -0.015929, -0.011810, -0.001170, 0.006999, 0.014346, 0.022026, 0.033087, 0.037703, 0.039304, 0.038986, 0.040531, 0.042739, 0.044912, 0.045850, 0.052980, 0.060894, 0.062495, 0.065477, 0.066306, 0.069035, 0.066301, 0.058359, 0.048879, 0.054660, 0.053906, 0.042834, 0.051292, 0.054304, 0.049390, 0.064968, 0.053062, 0.067337
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 80.0
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Peperations]
version = 1
points = 
	0.022498, 0.020830, 0.014175, -0.000111, -0.007965, -0.011932, -0.009252, -0.003320, -0.000118, 0.004151, 0.015991, 0.024593, 0.030148, 0.034696, 0.042241, 0.043592, 0.045307, 0.051419, 0.057700, 0.066468, 0.072764, 0.085492, 0.100446, 0.113063, 0.118900, 0.122870, 0.130290, 0.129755, 0.129462, 0.124089, 0.122420, 0.123461, 0.116841, 0.117893, 0.119241, 0.115227, 0.110631, 0.109920, 0.117187, 0.124332
	0.004953, 0.000716, -0.005511, -0.010742, -0.018400, -0.024021, -0.019665, -0.013525, -0.009878, -0.004126, 0.008939, 0.016408, 0.019292, 0.023840, 0.033007, 0.033600, 0.034448, 0.041047, 0.049029, 0.052882, 0.062512, 0.072410, 0.089182, 0.103027, 0.106205, 0.110789, 0.117912, 0.115269, 0.112784, 0.106051, 0.103603, 0.104209, 0.099603, 0.105100, 0.101466, 0.099610, 0.095780, 0.096420, 0.108661, 0.108286
	-0.007933, -0.002801, -0.011350, -0.022484, -0.029473, -0.033231, -0.030354, -0.021826, -0.018408, -0.013209, 0.001640, 0.008984, 0.012027, 0.014149, 0.024334, 0.028649, 0.030597, 0.034667, 0.041223, 0.046241, 0.051968, 0.062511, 0.079099, 0.090699, 0.097837, 0.101667, 0.108218, 0.106595, 0.104490, 0.095444, 0.089512, 0.089259, 0.089179, 0.091741, 0.094161, 0.094254, 0.091002, 0.088753, 0.095405, 0.102343
	-0.010759, -0.012564, -0.018170, -0.023960, -0.033106, -0.040910, -0.038354, -0.031441, -0.026122, -0.019953, -0.006267, 0.000733, 0.002678, 0.006102, 0.015437, 0.019860, 0.022689, 0.029563, 0.035629, 0.037302, 0.045089, 0.055137, 0.070820, 0.082978, 0.087158, 0.088614, 0.094487, 0.093851, 0.091038, 0.080923, 0.074433, 0.073797, 0.073058, 0.081788, 0.080734, 0.083111, 0.078149, 0.079373, 0.091335, 0.087853
	-0.027313, -0.019238, -0.027920, -0.036645, -0.043223, -0.049872, -0.048503, -0.043853, -0.040737, -0.035179, -0.021622, -0.013493, -0.010171, -0.007317, 0.001347, 0.007440, 0.011360, 0.015985, 0.023916, 0.026329, 0.031680, 0.042865, 0.056754, 0.067621, 0.072919, 0.075964, 0.080156, 0.081233, 0.077771, 0.068443, 0.063939, 0.062251, 0.063828, 0.065094, 0.069498, 0.071735, 0.067423, 0.064065, 0.069162, 0.076272
	-0.033298, -0.035618, -0.039940, -0.043358, -0.050731, -0.061413, -0.060545, -0.055944, -0.052261, -0.045471, -0.035624, -0.027633, -0.021472, -0.017300, -0.006949, -0.002776, -0.000154, 0.006413, 0.012882, 0.014721, 0.023411, 0.031711, 0.040565, 0.054702, 0.058761, 0.061734, 0.065369, 0.066037, 0.061059, 0.053849, 0.049600, 0.048373, 0.049189, 0.054631, 0.050470, 0.056349, 0.047074, 0.049651, 0.057444, 0.057485
	-0.046284, -0.039039, -0.049010, -0.054961, -0.061001, -0.068408, -0.069602, -0.066474, -0.063117, -0.059357, -0.049570, -0.041166, -0.035441, -0.029269, -0.019658, -0.012395, -0.008906, -0.005538, 0.002012, 0.008339, 0.013216, 0.018793, 0.031185, 0.040165, 0.047175, 0.050605, 0.054283, 0.054442, 0.049166, 0.043483, 0.039000, 0.040758, 0.040857, 0.040759, 0.042263, 0.043438, 0.040051, 0.035886, 0.041332, 0.048851
	-0.049893, -0.051919, -0.058103, -0.060142, -0.067656, -0.077159, -0.079195, -0.078019, -0.075421, -0.069471, -0.060409, -0.054194, -0.044226, -0.037275, -0.027912, -0.020020, -0.016789, -0.012491, -0.003457, 0.001129, 0.004540, 0.009435, 0.018232, 0.027941, 0.035138, 0.038227, 0.042656, 0.044103, 0.038517, 0.032121, 0.029666, 0.027319, 0.029774, 0.031572, 0.028887, 0.034828, 0.023795, 0.030023, 0.033606, 0.036047
	-0.061015, -0.055279, -0.067497, -0.072234, -0.078637, -0.083600, -0.085954, -0.087271, -0.088647, -0.083447, -0.073398, -0.065920, -0.058009, -0.048810, -0.040714, -0.032533, -0.027328, -0.020402, -0.011382, -0.006547, -0.005452, -0.002712, 0.004649, 0.014201, 0.021442, 0.025510, 0.032890, 0.034711, 0.030965, 0.026329, 0.018828, 0.019246, 0.018861, 0.019611, 0.020596, 0.021396, 0.020172, 0.015723, 0.020537, 0.029677
	-0.063777, -0.066149, -0.073750, -0.076131, -0.084016, -0.091900, -0.093741, -0.094496, -0.094840, -0.089548, -0.084332, -0.077263, -0.068485, -0.061963, -0.051082, -0.043658, -0.037912, -0.032323, -0.024324, -0.019914, -0.018261, -0.013727, -0.003485, 0.004316, 0.011418, 0.017023, 0.022980, 0.024505, 0.018896, 0.014000, 0.009498, 0.006074, 0.009480, 0.007611, 0.008958, 0.010086, -0.000341, 0.010423, 0.010467, 0.016794
	-0.072341, -0.064233, -0.079217, -0.084483, -0.091050, -0.094481, -0.095378, -0.096667, -0.100564, -0.098313, -0.093254, -0.086700, -0.079209, -0.071795, -0.061313, -0.051911, -0.046317, -0.042643, -0.037228, -0.031598, -0.027431, -0.020480, -0.012883, -0.003114, 0.004746, 0.010189, 0.015911, 0.017106, 0.014037, 0.008693, 0.005120, 0.003652, -0.000532, -0.001097, 0.001984, 0.000397, -0.002089, -0.002821, 0.000529, 0.009043
	-0.068927, -0.075835, -0.083530, -0.085213, -0.091299, -0.100015, -0.101020, -0.100921, -0.103349, -0.102493, -0.098069, -0.091292, -0.083452, -0.079672, -0.069612, -0.062472, -0.055862, -0.052233, -0.046746, -0.041991, -0.035219, -0.028225, -0.018698, -0.007309, -0.002458, 0.002051, 0.006595, 0.008468, 0.005218, -0.000205, -0.003131, -0.003647, -0.006151, -0.009154, -0.005539, -0.006971, -0.015297, -0.002874, -0.005242, 0.003706
	-0.070116, -0.067835, -0.086390, -0.089881, -0.095167, -0.099194, -0.100751, -0.103794, -0.106996, -0.105835, -0.098564, -0.092154, -0.085579, -0.083053, -0.074722, -0.066442, -0.059302, -0.053429, -0.047800, -0.042952, -0.039132, -0.034614, -0.025732, -0.012689, -0.005906, 0.001101, 0.006644, 0.010980, 0.007742, 0.002526, -0.000261, -0.004094, -0.008771, -0.008465, -0.007095, -0.008952, -0.010405, -0.010446, -0.006121, 0.002024
	-0.064366, -0.071780, -0.082938, -0.085702, -0.093522, -0.099237, -0.104020, -0.105939, -0.106226, -0.104298, -0.097541, -0.091253, -0.084969, -0.082450, -0.075561, -0.066547, -0.056511, -0.051248, -0.041287, -0.037794, -0.035633, -0.028059, -0.019518, -0.010556, -0.003388, 0.002054, 0.009492, 0.011478, 0.008555, 0.004735, -0.000781, -0.006427, -0.005697, -0.010270, -0.006112, -0.011704, -0.018717, -0.002750, -0.010971, 0.000116
	-0.076795, -0.064801, -0.080209, -0.085175, -0.093457, -0.101077, -0.104981, -0.106367, -0.106821, -0.105708, -0.098545, -0.090759, -0.086929, -0.083491, -0.074306, -0.064805, -0.055933, -0.049959, -0.042853, -0.036270, -0.034463, -0.029587, -0.018780, -0.010103, -0.003533, 0.001632, 0.007909, 0.014370, 0.009281, 0.004666, -0.002974, -0.007301, -0.010185, -0.008299, -0.006340, -0.009678, -0.011333, -0.010684, -0.006289, 0.002763
	-0.067470, -0.065770, -0.074038, -0.076420, -0.085702, -0.098704, -0.101940, -0.102629, -0.101903, -0.100342, -0.093820, -0.086941, -0.083804, -0.081020, -0.067700, -0.059395, -0.054055, -0.047911, -0.039687, -0.035672, -0.032029, -0.025979, -0.017057, -0.006973, -0.001656, 0.002001, 0.007249, 0.012112, 0.006541, 0.000572, -0.006284, -0.010415, -0.012279, -0.015087, -0.007848, -0.016491, -0.019704, -0.005357, -0.013151, 0.002966
	-0.074820, -0.054794, -0.069710, -0.075127, -0.082743, -0.091434, -0.095621, -0.097541, -0.099098, -0.097422, -0.089851, -0.083594, -0.081112, -0.078942, -0.066391, -0.057457, -0.050942, -0.048077, -0.041211, -0.034391, -0.030091, -0.026047, -0.014207, -0.005090, 0.000912, 0.005316, 0.010043, 0.015509, 0.011199, 0.004513, -0.001027, -0.006694, -0.011239, -0.011162, -0.009134, -0.013596, -0.014031, -0.011306, -0.007627, 0.001767
	-0.061695, -0.056074, -0.065188, -0.067950, -0.076218, -0.088303, -0.093436, -0.092999, -0.090937, -0.090555, -0.084407, -0.080354, -0.078692, -0.074308, -0.062767, -0.052729, -0.047475, -0.043949, -0.036669, -0.031720, -0.027940, -0.020058, -0.010125, -0.000940, 0.003512, 0.007720, 0.011869, 0.015296, 0.011180, 0.003886, -0.003309, -0.003380, -0.007926, -0.011633, -0.003540, -0.014182, -0.013975, -0.003720, -0.011797, 0.006338
	-0.070864, -0.046187, -0.061128, -0.065717, -0.072715, -0.083470, -0.088292, -0.087558, -0.087628, -0.089378, -0.083768, -0.077237, -0.077063, -0.071978, -0.061635, -0.052022, -0.046913, -0.041194, -0.034314, -0.028661, -0.027048, -0.021438, -0.009769, -0.001205, 0.004637, 0.008928, 0.013264, 0.017277, 0.013442, 0.007295, 0.003623, -0.002524, -0.004256, -0.005789, -0.004213, -0.007305, -0.010487, -0.010885, -0.006086, 0.007386
	-0.059345, -0.049207, -0.056858, -0.060052, -0.066579, -0.080604, -0.086910, -0.085647, -0.085267, -0.087618, -0.081260, -0.075368, -0.073937, -0.069758, -0.058235, -0.051634, -0.045288, -0.038732, -0.032262, -0.027928, -0.024928, -0.019266, -0.007996, 0.000923, 0.005834, 0.008336, 0.013557, 0.017068, 0.012350, 0.006475, 0.000982, 0.001103, -0.006223, -0.006853, -0.000966, -0.013148, -0.013975, -0.006310, -0.011605, 0.006165
	-0.066591, -0.039715, -0.053663, -0.059514, -0.065911, -0.075018, -0.080214, -0.082968, -0.083447, -0.085380, -0.079055, -0.071985, -0.070247, -0.065856, -0.057767, -0.049975, -0.044481, -0.039103, -0.031217, -0.024927, -0.020997, -0.016440, -0.004831, 0.004061, 0.009463, 0.011160, 0.014777, 0.020638, 0.017816, 0.011360, 0.006171, 0.002164, -0.002119, -0.003117, -0.003031, -0.005156, -0.011400, -0.011762, -0.009295, -0.000001
	-0.060314, -0.046160, -0.052794, -0.054967, -0.062049, -0.074106, -0.080446, -0.081200, -0.080809, -0.080477, -0.076170, -0.070932, -0.069101, -0.063634, -0.055720, -0.049501, -0.044939, -0.040131, -0.032438, -0.022882, -0.017627, -0.012524, -0.001324, 0.006685, 0.011868, 0.013658, 0.016095, 0.021837, 0.020158, 0.012528, 0.006089, 0.005453, -0.000976, -0.002140, 0.001104, -0.010111, -0.010612, -0.007452, -0.014357, 0.001011
	-0.075633, -0.036609, -0.049346, -0.055490, -0.059336, -0.067616, -0.073859, -0.075613, -0.076372, -0.078009, -0.070627, -0.064206, -0.064430, -0.061999, -0.054551, -0.047386, -0.040817, -0.037398, -0.028062, -0.018505, -0.012195, -0.007531, 0.001481, 0.011790, 0.019955, 0.022349, 0.022131, 0.024492, 0.023359, 0.019186, 0.014655, 0.008357, 0.004176, 0.002971, 0.002955, -0.000237, -0.005884, -0.010152, -0.009506, 0.002811
	-0.059008, -0.039658, -0.046978, -0.048324, -0.052285, -0.063338, -0.069082, -0.070556, -0.070625, -0.070049, -0.064460, -0.057403, -0.056723, -0.052882, -0.046968, -0.041507, -0.033211, -0.029974, -0.022900, -0.013579, -0.008803, -0.004962, 0.005653, 0.017026, 0.028171, 0.028651, 0.024731, 0.026850, 0.023371, 0.017073, 0.015171, 0.016616, 0.005521, 0.005756, 0.007586, -0.005103, -0.006856, -0.005604, -0.006599, 0.007528
	-0.068330, -0.030233, -0.043154, -0.047439, -0.047149, -0.051149, -0.060971, -0.063014, -0.065775, -0.064636, -0.058200, -0.050987, -0.050925, -0.050115, -0.041299, -0.033907, -0.026306, -0.024199, -0.017123, -0.009196, -0.006314, -0.003809, 0.004760, 0.015324, 0.026665, 0.029649, 0.028724, 0.027131, 0.025150, 0.021808, 0.019981, 0.016766, 0.012347, 0.008776, 0.005760, -0.000224, -0.004294, -0.005879, -0.002457, 0.010054
	-0.053519, -0.031388, -0.038255, -0.037590, -0.039245, -0.046335, -0.056314, -0.057830, -0.060291, -0.058967, -0.051413, -0.045449, -0.043947, -0.042018, -0.034113, -0.025887, -0.019539, -0.017727, -0.012711, -0.005860, -0.003102, 0.000774, 0.009438, 0.015884, 0.022961, 0.024229, 0.026012, 0.029407, 0.026717, 0.020406, 0.017796, 0.020289, 0.012243, 0.009711, 0.009234, -0.005990, -0.001013, 0.000740, -0.002144, 0.013012
	-0.068972, -0.023416, -0.032912, -0.036134, -0.035915, -0.040435, -0.047452, -0.051460, -0.055021, -0.055776, -0.048697, -0.039554, -0.036785, -0.035561, -0.029056, -0.021075, -0.013416, -0.012134, -0.007237, -0.000622, 0.001662, 0.005393, 0.012038, 0.019764, 0.023514, 0.026252, 0.028191, 0.031400, 0.031365, 0.027993, 0.023275, 0.021009, 0.018930, 0.014093, 0.009022, 0.004773, 0.002094, 0.001348, 0.005643, 0.015078
	-0.050527, -0.022437, -0.028090, -0.026206, -0.028387, -0.036911, -0.041310, -0.044227, -0.046970, -0.046769, -0.038081, -0.031386, -0.029516, -0.024050, -0.019435, -0.012381, -0.005732, -0.004173, 0.000911, 0.006849, 0.007360, 0.010699, 0.017436, 0.023369, 0.028527, 0.029640, 0.031002, 0.034727, 0.036582, 0.030763, 0.026015, 0.028623, 0.020834, 0.016185, 0.016933, 0.002829, 0.004984, 0.009818, 0.008874, 0.020032
	-0.067395, -0.010220, -0.021024, -0.024567, -0.024087, -0.029620, -0.032317, -0.034341, -0.038392, -0.038789, -0.030285, -0.021590, -0.017175, -0.014435, -0.007732, -0.000529, 0.005605, 0.007078, 0.012454, 0.017758, 0.016774, 0.015574, 0.020748, 0.028369, 0.033644, 0.034771, 0.036537, 0.040293, 0.042118, 0.039979, 0.035655, 0.033354, 0.030928, 0.024890, 0.021491, 0.018938, 0.013668, 0.012501, 0.017108, 0.023515
	-0.038833, -0.012802, -0.018564, -0.017459, -0.019062, -0.027068, -0.030119, -0.028336, -0.029665, -0.030695, -0.022239, -0.013522, -0.008358, -0.004785, 0.000463, 0.010662, 0.015564, 0.016950, 0.020281, 0.025300, 0.022680, 0.022717, 0.026679, 0.031617, 0.035801, 0.037098, 0.041294, 0.045640, 0.047879, 0.042000, 0.038044, 0.040629, 0.033892, 0.031247, 0.031584, 0.018500, 0.020116, 0.019823, 0.016638, 0.029979
	-0.054356, -0.002258, -0.012712, -0.017288, -0.016713, -0.022907, -0.024293, -0.021563, -0.022620, -0.021953, -0.015330, -0.005386, -0.000764, 0.002640, 0.009997, 0.022869, 0.028174, 0.027730, 0.030977, 0.035707, 0.032818, 0.030889, 0.033638, 0.038561, 0.044265, 0.045141, 0.047683, 0.051815, 0.054004, 0.050991, 0.045574, 0.043899, 0.044055, 0.039092, 0.035909, 0.032091, 0.026891, 0.022169, 0.024865, 0.030848
	-0.031827, -0.000102, -0.006368, -0.006487, -0.006247, -0.014001, -0.017110, -0.013043, -0.010851, -0.008764, -0.000213, 0.006477, 0.011144, 0.018309, 0.024745, 0.033643, 0.038648, 0.039249, 0.041148, 0.045266, 0.041693, 0.040999, 0.045484, 0.052613, 0.057066, 0.054753, 0.055112, 0.059287, 0.060203, 0.052465, 0.047993, 0.050999, 0.047464, 0.046460, 0.044507, 0.031433, 0.032267, 0.032025, 0.029852, 0.040329
	-0.053848, 0.008122, -0.005187, -0.009032, -0.006543, -0.010012, -0.013005, -0.011663, -0.008957, -0.004668, 0.005458, 0.012800, 0.016893, 0.023554, 0.031737, 0.038741, 0.043870, 0.043337, 0.046621, 0.047581, 0.045654, 0.044827, 0.050363, 0.058747, 0.061023, 0.060485, 0.059059, 0.061821, 0.061391, 0.055971, 0.051067, 0.050038, 0.051018, 0.046533, 0.043334, 0.042562, 0.036118, 0.029798, 0.032773, 0.039524
	-0.025830, 0.006164, -0.000655, 0.000164, 0.000088, -0.008033, -0.011008, -0.006017, -0.001301, 0.004088, 0.011848, 0.020276, 0.024465, 0.033383, 0.039126, 0.044268, 0.047916, 0.047402, 0.050050, 0.050456, 0.048891, 0.051771, 0.058154, 0.063246, 0.065463, 0.063072, 0.060950, 0.065351, 0.064614, 0.057455, 0.051194, 0.055723, 0.050906, 0.046407, 0.048283, 0.036561, 0.037400, 0.036887, 0.031589, 0.046759
	-0.041184, 0.017683, 0.006408, 0.000358, 0.001923, -0.002498, -0.003907, -0.001746, 0.001864, 0.006784, 0.017297, 0.026916, 0.030940, 0.036439, 0.045987, 0.050809, 0.054636, 0.052055, 0.053180, 0.056698, 0.057069, 0.055779, 0.063193, 0.067815, 0.071856, 0.070651, 0.067674, 0.070718, 0.070797, 0.062598, 0.057842, 0.056835, 0.056713, 0.051260, 0.048727, 0.048227, 0.044844, 0.039559, 0.041218, 0.044920
	-0.014008, 0.018619, 0.011274, 0.010878, 0.008771, 0.001246, -0.001819, 0.003600, 0.008052, 0.011983, 0.021970, 0.030757, 0.037662, 0.045972, 0.053195, 0.057661, 0.059206, 0.058383, 0.060240, 0.061039, 0.062504, 0.064497, 0.070278, 0.077704, 0.080246, 0.077015, 0.072985, 0.075685, 0.072584, 0.063534, 0.057732, 0.061938, 0.057545, 0.050931, 0.054863, 0.045820, 0.048882, 0.049675, 0.043484, 0.051538
	-0.045038, 0.028947, 0.019821, 0.012917, 0.013648, 0.007951, 0.005122, 0.007823, 0.012411, 0.015320, 0.025036, 0.036734, 0.045314, 0.052208, 0.062220, 0.065610, 0.068489, 0.066665, 0.068454, 0.069025, 0.071080, 0.073373, 0.079623, 0.085651, 0.088907, 0.088954, 0.084254, 0.084464, 0.080300, 0.072471, 0.067316, 0.066430, 0.065143, 0.057630, 0.058650, 0.059627, 0.057197, 0.054105, 0.055295, 0.057879
	-0.017117, 0.027364, 0.023067, 0.022758, 0.019246, 0.011825, 0.007962, 0.011522, 0.017237, 0.021779, 0.031329, 0.042642, 0.052349, 0.060322, 0.069568, 0.074657, 0.075211, 0.072882, 0.075373, 0.078391, 0.079512, 0.081816, 0.086101, 0.091730, 0.095061, 0.095682, 0.092100, 0.092873, 0.085769, 0.077219, 0.068392, 0.073179, 0.069972, 0.061240, 0.068306, 0.062227, 0.061008, 0.064520, 0.058543, 0.070728
	-0.042759, 0.035472, 0.029514, 0.023812, 0.024176, 0.020576, 0.017397, 0.018716, 0.022981, 0.027634, 0.041262, 0.050991, 0.058558, 0.067060, 0.077829, 0.083609, 0.084719, 0.082815, 0.085352, 0.087363, 0.091238, 0.091692, 0.096562, 0.102513, 0.106436, 0.108184, 0.105828, 0.107257, 0.102415, 0.090768, 0.084257, 0.081410, 0.081286, 0.073523, 0.074433, 0.076576, 0.070376, 0.068350, 0.071896, 0.072962
	-0.003143, 0.035517, 0.033266, 0.032727, 0.031843, 0.025862, 0.023177, 0.026936, 0.032953, 0.037457, 0.049289, 0.057429, 0.066625, 0.072540, 0.083814, 0.089321, 0.092420, 0.093053, 0.094752, 0.096876, 0.098364, 0.101271, 0.105185, 0.113505, 0.115784, 0.118957, 0.117138, 0.117934, 0.110930, 0.101497, 0.091051, 0.092731, 0.090574, 0.079282, 0.084691, 0.078426, 0.073451, 0.081698, 0.072811, 0.084352
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 19.8
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 130, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 123, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 112, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 1766, in load_config
    return BedMesh(config)
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 107, in __init__
    self.splitter = MoveSplitter(config, self.gcode)
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 1259, in __init__
    self.split_delta_z = config.getfloat(
  File "/home/pi/klipper/klippy/configfile.py", line 70, in getfloat
    return self._get_wrapper(self.fileconfig.getfloat, option, default,
  File "/home/pi/klipper/klippy/configfile.py", line 49, in _get_wrapper
    raise error("Option '%s' in section '%s' must have minimum of %s"
configparser.Error: Option 'split_delta_z' in section 'bed_mesh' must have minimum of 0.01
webhooks client 4127599392: New connection
webhooks client 4127599392: Client info {'program': 'Moonraker', 'version': 'v0.9.3-0-g71f9e67'}
Attempting MCU 'mcu' reset
Unable to issue reset command on MCU 'rpi'
Attempting MCU 'toolboard_t0' reset
Attempting MCU 'toolboard_t1' reset
Attempting MCU 'dinghy' reset
Attempting MCU 'plasma' reset
webhooks client 4127599392: Disconnected
Restarting printer
Start printer at Tue Mar 17 04:00:48 2026 (1773720048.3 9652.7)
===== Config file =====
[mcu rpi]
serial = /tmp/klipper_host_mcu

[board_pins btt-octopus-pro-h723-11]
aliases = 
	
	
	
	x_step_pin=PF13,
	x_dir_pin=PF12,
	x_enable_pin=PF14,
	x_uart_pin=PC4,
	x_diag_pin=PG6,
	x_endstop_pin=PG6,
	
	
	
	dual_carriage_step_pin=PF9,
	dual_carriage_dir_pin=PF10,
	dual_carriage_enable_pin=PG2,
	dual_carriage_uart_pin=PF2,
	dual_carriage_diag_pin=PG12,
	dual_carriage_endstop_pin=PG12,
	
	
	
	y_step_pin=PG0,
	y_dir_pin=PG1,
	y_enable_pin=PF15,
	y_uart_pin=PD11,
	y_diag_pin=PG9,
	y_endstop_pin=PG9,
	
	
	
	y1_step_pin=PG4,
	y1_dir_pin=PC1,
	y1_enable_pin=PA2,
	y1_uart_pin=PC7,
	y1_diag_pin=PG11,
	y1_endstop_pin=PG11,
	
	
	
	z0_step_pin=PC13,
	z0_dir_pin=PF0,
	z0_enable_pin=PF1,
	z0_uart_pin=PE4,
	z0_diag_pin=PG13,
	
	
	
	z1_step_pin=PE2,
	z1_dir_pin=PE3,
	z1_enable_pin=PD4,
	z1_uart_pin=PE1,
	z1_diag_pin=PG14,
	
	
	
	z2_step_pin=PE6,
	z2_dir_pin=PA14,
	z2_enable_pin=PE0,
	z2_uart_pin=PD3,
	z2_diag_pin=PG15,
	
	e_step_pin=PF11,
	e_dir_pin=PG3,
	e_enable_pin=PG5,
	e_uart_pin=PC6,
	
	e_heater_pin=PA2,
	e_sensor_pin=PF4,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=PA7,
	stepper_spi_miso_pin=PA6,
	stepper_spi_sclk_pin=PA5,
	adxl345_cs_pin=PA15,
	bltouch_sensor_pin=PB7,
	bltouch_control_pin=PB6,
	probe_pin=PB7,
	fan_part_cooling_pin=PA8,
	fan_toolhead_cooling_pin=PE5,
	fan_controller_board_pin=PD12,
	heater_bed_heating_pin=PA1,
	heater_bed_sensor_pin=PF3,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PG15,
	filament_sensor_motion_pin=PG14,
	ratrig_vaoc_probe_pin=PG10,
	ratrig_vaoc_led_pin=PB0,
	ratrig_vaoc_fan_pin=PD13,
	chamber_lighting_pin=PB11,
	chamber_filter_4p_fan_pin=PD14,
	chamber_filter_4p_fan_enable_pin=PD15

[mcu]
serial = /dev/RatOS/btt-octopus-pro-h723-11

[temperature_sensor Octopus_Pro_H723_V1.1]
sensor_type = temperature_mcu

[adxl345 controlboard]
cs_pin = PA15
spi_software_mosi_pin = PB5
spi_software_miso_pin = PB4
spi_software_sclk_pin = PB3

[board_pins toolboard_t0]
mcu = toolboard_t0
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t0]
serial = /dev/RatOS/btt-ebb42-gen2-10-t0

[temperature_sensor EBB42_Gen2_v1.0_T0]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t0

[lis2dw toolboard_t0]
axes_map = x, z, y
cs_pin = toolboard_t0:PB1
spi_software_mosi_pin = toolboard_t0:PB11
spi_software_miso_pin = toolboard_t0:PB2
spi_software_sclk_pin = toolboard_t0:PB10

[board_pins toolboard_t1]
mcu = toolboard_t1
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t1]
serial = /dev/RatOS/btt-ebb42-gen2-10-t1

[temperature_sensor EBB42_Gen2_v1.0_T1]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t1

[lis2dw toolboard_t1]
axes_map = x, z, y
cs_pin = toolboard_t1:PB1
spi_software_mosi_pin = toolboard_t1:PB11
spi_software_miso_pin = toolboard_t1:PB2
spi_software_sclk_pin = toolboard_t1:PB10

[gcode_macro RatOS]
variable_homing = "endstops"
variable_z_probe = "static"
variable_sensorless_x_current = 0.6
variable_sensorless_y_current = 0.9
variable_safe_home_x = "middle"
variable_safe_home_y = "middle"
variable_driver_type_x = "tmc2209"
variable_driver_type_y = "tmc2209"
variable_stowable_probe_stop_on_error = False
variable_chamber_filter_enable = True
variable_chamber_filter_speed = 0.5
variable_chamber_filter_disable_speed = 1.0
variable_chamber_filter_enable_at = "after_print_start"
variable_chamber_filter_disable_period = 300
variable_chamber_filter_disable_bed_temp = 0
variable_chamber_heater_enable = True
variable_chamber_heater_bed_temp = 115
variable_chamber_heater_preheating_temp = 150
variable_chamber_heater_heating_temp_offset = 25
variable_chamber_heater_control_external_heater = False
variable_chamber_heater_air_circulation_enable = True
variable_chamber_heater_air_circulation_fan_speed = 0.35
variable_chamber_heater_air_circulation_y_pos = 0
variable_chamber_heater_air_circulation_z_pos = 100
variable_chamber_heater_extra_fan_speed = 1.0
variable_chamber_heater_filter_fan_speed = 1.0
variable_bed_heat_soak_time = 0
variable_hotend_heat_soak_time = 0
variable_led_status_action = 0.0,1.0,1.0
variable_led_status_success = 0.0,1.0,0.0
variable_led_status_error = 1.0,0.0,1.0
variable_led_status_on = 1.0,1.0,1.0
variable_led_status_off = 0.0,0.0,1.0
variable_led_status_standby = 0.1,0.1,0.1
variable_led_status_heating = 1.0,0.0,0.0
variable_led_status_cooling = 0.0,0.0,1.0
variable_calibrate_bed_mesh = True
variable_adaptive_mesh = True
variable_start_print_park_in = "center"
variable_start_print_park_z_height = 3
variable_end_print_park_in = "back"
variable_pause_print_park_in = "back"
variable_end_print_park_z_hop = 20
variable_nozzle_priming = "primeblob"
variable_nozzle_prime_start_x = "max"
variable_nozzle_prime_start_y = "min"
variable_nozzle_prime_direction = "auto"
variable_nozzle_prime_bridge_fan = 102
variable_probe_for_priming_result = None
variable_probe_for_priming_end_result = None
variable_probe_for_priming_result_t1 = None
variable_probe_for_priming_end_result_t1 = None
variable_probe_for_priming_disable_mesh_constraints = False
variable_adaptive_prime_offset_threshold = -1.0
variable_last_z_offset = None
variable_runout_park_in = "front"
variable_enable_unload_tip_forming = False
variable_filament_unload_length = 150
description = RatOS variable storage macro, will echo variables to the console when run.
variable_relative_extrusion = True
variable_force_absolute_position = False
variable_preheat_extruder = True
variable_preheat_extruder_temp = 150
variable_macro_travel_speed = 600
variable_macro_travel_accel = 8000
variable_macro_z_speed = 15
variable_bed_margin_x = [59.6, 59.6]
variable_bed_margin_y = [14.35, 33.65]
variable_printable_x_min = 0
variable_printable_x_max = 0
variable_printable_y_min = 0
variable_printable_y_max = 0
variable_end_print_motors_off = True
variable_status_color_ok = "00FF00"
variable_status_color_error = "FF0000"
variable_status_color_unknown = "FFFF00"
variable_end_print_retract_filament = 10
gcode = 
	ECHO_RATOS_VARS
variable_auto_center_subject = False
variable_toolchange_zhop = 2.0
variable_toolchange_zspeed = 25
variable_toolchange_sync_fans = False
variable_toolchange_combined_zhop = False
variable_toolchange_travel_speed = 600
variable_toolchange_travel_accel = 8000
variable_toolchange_extrusion = 2.0
variable_toolchange_retraction = 2.0
variable_toolchange_feedrate = 7200
variable_toolchange_prepurging_timer = 0
variable_toolchange_standby_temp = -1
variable_toolchange_purge = 25
variable_toolchange_first_purge = 50
variable_beacon_bed_mesh_scv = 25
variable_beacon_contact_z_homing = False
variable_beacon_contact_start_print_true_zero = True
variable_beacon_contact_start_print_true_zero_fuzzy_position = True
variable_beacon_contact_calibrate_model_on_true_zero = True
variable_beacon_contact_wipe_before_true_zero = True
variable_beacon_contact_wipe_before_true_zero_method = "probe_clean"
variable_beacon_contact_true_zero_temp = 170
variable_beacon_contact_prime_probing = True
variable_beacon_contact_expansion_compensation = True
variable_beacon_contact_bed_mesh = False
variable_beacon_contact_bed_mesh_samples = 2
variable_beacon_contact_z_tilt_adjust = False
variable_beacon_contact_z_tilt_adjust_samples = 2
variable_beacon_scan_compensation_enable = True
variable_beacon_scan_compensation_profile = "auto"
variable_beacon_scan_compensation_desired_spacing = 10
variable_beacon_scan_compensation_bed_temp_mismatch_is_error = False
variable_beacon_contact_poke_bottom_limit = -1
variable_beacon_scan_method_automatic = False
variable_beacon_adaptive_heat_soak = True
variable_beacon_adaptive_heat_soak_max_wait = 5400
variable_beacon_adaptive_heat_soak_extra_wait_after_completion = 0
variable_beacon_adaptive_heat_soak_layer_quality = 3
variable_beacon_adaptive_heat_soak_maximum_first_layer_duration = 1800
variable_beacon_contact_start_print_true_zero_fuzzy_radius = 20
variable_homing_x = "endstop"
variable_homing_y = "endstop"
variable_default_toolhead = 0
variable_adxl_chip = ["lis2dw toolboard_t0", "lis2dw toolboard_t1"]
variable_shaper_x_freq = [54.2, 53.2, 53.6, 54.4]
variable_shaper_y_freq = [40.8, 47.6, 38.6, 38]
variable_shaper_x_type = ["mzv", "mzv", "mzv", "mzv"]
variable_shaper_y_type = ["mzv", "mzv", "mzv", "mzv"]
variable_x_driver_types = ["tmc5160"]
variable_x_axes = ["x"]
variable_y_driver_types = ["tmc5160", "tmc5160"]
variable_y_axes = ["y", "y1"]
variable_z_driver_types = ["tmc2209", "tmc2209", "tmc2209"]
variable_z_axes = ["z", "z1", "z2"]
variable_home_y_first = True

[ratos_homing]
axes = xyz
z_hop = 15
z_hop_speed = 15
gcode = 
	
	_LED_ON
	
	
	{% set prev_stop_on_error = printer["gcode_macro RatOS"].stowable_probe_stop_on_error %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set target_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	_IDEX_SINGLE
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE=True
	
	
	M400
	
	G90
	
	
	{% set X = true if params.X is defined else false %}
	{% set Y = true if params.Y is defined else false %}
	{% set Z = true if params.Z is defined else false %}
	{% if printer["gcode_macro RatOS"].home_y_first|default(false)|lower == 'true' %}
	HOME_Y X={X} Y={Y} Z={Z}
	HOME_X X={X} Y={Y} Z={Z}
	{% else %}
	HOME_X X={X} Y={Y} Z={Z}
	HOME_Y X={X} Y={Y} Z={Z}
	{% endif %}
	HOME_Z X={X} Y={Y} Z={Z}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE={prev_stop_on_error}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[gcode_macro HOME_X]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_x = printer["gcode_macro RatOS"].homing_x|lower %}
	{% set homing_x = homing_x if homing_x else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_X" MSG="printable_x_max: {printable_x_max}, safe_home_x: {safe_home_x}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}"
	
	
	{% if X or not Y and not Z %}
	{% if homing_x == 'endstop' %}
	G28 X
	{% elif homing_x == 'sensorless' %}
	{% if printer["dual_carriage"] is defined %}
	{ action_emergency_stop("sensorless homing not supported on IDEX!") }
	{% endif %}
	HOME_X_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_x to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_x, homing)) }
	{% endif %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1} MODE=PRIMARY
	G1 X{parking_position} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	{% endif %}
	{% set x_homed = True %}
	G0 X{safe_home_x} F{speed}
	M400
	{% endif %}

[gcode_macro HOME_Y]
gcode = 
	
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_y = printer["gcode_macro RatOS"].homing_y|lower %}
	{% set homing_y = homing_y if homing_y else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Y" MSG="printable_y_max: {printable_y_max}, safe_home_y: {safe_home_y}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}"
	
	
	{% if Y or not X and not Z %}
	{% if homing_y == 'endstop' %}
	G28 Y
	{% elif homing_y == 'sensorless' %}
	HOME_Y_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_y to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_y, homing)) }
	{% endif %}
	{% set y_homed = True %}
	G0 Y{safe_home_y} F{speed}
	{% endif %}

[gcode_macro HOME_Z]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	
	
	{% set beacon_contact_z_homing = true if printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_z_home_position_fuzzing_radius = printer["gcode_macro RatOS"].beacon_z_home_position_fuzzing_radius|default(0)|float %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Z" MSG="x_homed: {x_homed}, y_homed: {y_homed}, z_probe: {z_probe}, beacon_contact_z_homing: {beacon_contact_z_homing}"
	
	
	{% if Z or not Y and not X %}
	RATOS_ECHO MSG="Homing Z"
	{% if x_homed == False or y_homed == False %}
	{ action_emergency_stop("X and Y must be homed before homing Z") }
	{% else %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_homing %}
	{% if beacon_contact_start_print_true_zero %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% else %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	{% else %}
	G28 Z
	{% endif %}
	_Z_HOP
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro HOME_X_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	
	G4 P300
	
	G28 X
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"

[gcode_macro HOME_Y_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	
	G4 P300
	
	G28 Y
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"

[gcode_macro _Z_HOP]
description = Move Z axis up by Z_HOP distance at Z_HOP_SPEED. In relative mode it will move Z axis up by Z_HOP distance. In absolute mode it will move Z axis to Z_HOP distance.
gcode = 
	{% set z_hop = printer.fastconfig.config.ratos_homing.z_hop|float %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	G0 Z{z_hop} F{z_hop_speed}

[gcode_macro __MOVE_TO_SAFE_Z_HOME_ECHO_DEBUG]
gcode = 
	DEBUG_ECHO PREFIX="_MOVE_TO_SAFE_Z_HOME" MSG="x: {params.X}, y: {params.Y}, z_hop: {params.Z_HOP}, fuzzy_radius: {params.FUZZY_RADIUS}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}, printable_x_max: {printer['gcode_macro RatOS'].printable_x_max}, printable_y_max: {printer['gcode_macro RatOS'].printable_y_max}"

[gcode_macro MAYBE_HOME]
description = Only home unhomed axis. Specify ABL=1 to also ensure that automatic bed levelling is applied (if configured).
variable_is_kinematic_position_overriden = False
gcode = 
	{% set abl = params.ABL|default('')|lower in ('true', 'yes', '1') %}
	{% if printer["gcode_macro MAYBE_HOME"].is_kinematic_position_overriden|lower == 'true' %}
	RATOS_ECHO MSG="SET_CENTER_KINEMATIC_POSITION has been abused. Homing all axes. Please refrain from using SET_CENTER_KINEMATIC_POSITION outside of debugging purposes."
	G28
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=False
	{% else %}
	{% set axes = '' %}
	{% set isHomed = true %}
	{% set axesToHome = '' %}
	{% if params.X is defined %}
	{% set axes = axes ~ 'X ' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% endif %}
	{% if params.Y is defined %}
	{% set axes = axes ~ 'Y ' %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% endif %}
	{% if params.Z is defined %}
	{% set axes = axes ~ 'Z ' %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if params.X is not defined and params.Y is not defined and params.Z is not defined %}
	{% set axes = '' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if isHomed is false %}
	RATOS_ECHO MSG="Homing {axesToHome}"
	G28 {axesToHome}
	{% else %}
	RATOS_ECHO MSG="All requested axes already homed. Skipping homing."
	{% endif %}
	{% endif %}
	{% if abl %}
	{% if printer.z_tilt is defined %}
	{% if not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Performing Z tilt adjustment..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Z tilt already applied. Skipping Z tilt adjustment."
	{% endif %}
	{% elif printer.quad_gantry_level is defined %}
	{% if not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Performing quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Quad gantry leveling already applied. Skipping quad gantry leveling."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="No automatic bed leveling method configured. Skipping bed leveling."
	{% endif %}
	{% endif %}

[gcode_macro PID_CALIBRATE_HOTEND]
description = Perform a PID calibration test for a given extruder heater.
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set temp = params.TEMP|default(220)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_HOTEND" MSG="TEMP={temp}"
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO MSG="PID calibration hotend heater T0 at {temp}°C..."
	PID_CALIBRATE HEATER=extruder TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	
	{% if toolhead==0 or toolhead==1 %}
	RATOS_ECHO MSG="PID calibration hotend heater T{toolhead} at {temp}°C..."
	PID_CALIBRATE HEATER=extruder{'' if toolhead==0 else toolhead} TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_BED]
description = Perform a PID calibration test for the bed heater.
gcode = 
	
	{% set temp = params.TEMP|default(80)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_BED" MSG="TEMP={temp}"
	RATOS_ECHO MSG="PID calibration bed heater at {temp}°C..."
	
	
	PID_CALIBRATE HEATER=heater_bed TARGET={temp}
	
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_CHAMBER_HEATER]
description = Perform a PID calibration test for the chamber heater.
gcode = 
	
	{% set temp = params.TEMP|default(150)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_CHAMBER_HEATER" MSG="TEMP={temp}"
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	RATOS_ECHO MSG="PID calibration chamber heater at {temp}°C..."
	PID_CALIBRATE HEATER=chamber_heater TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_heater" %}
	{% set link_text = "RatOS Chamber Heater" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber heater found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro INITIALIZE_PA_TUNING]
description = Start a pressure advance tuning tower.
gcode = 
	
	{% set start = params.START|default(0.0)|float %}
	{% set factor = params.FACTOR|default(0.001)|float %}
	
	
	{% set layer_number = printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|default(0)|int %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if is_printing_gcode and layer_number < 2 %}
	DEBUG_ECHO PREFIX="START_PA_TOWER" MSG="START: {start}, FACTOR: {factor}"
	RATOS_ECHO MSG="Starting pressure advance tuning tower..."
	TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START={start} FACTOR={factor}
	{% else %}
	RATOS_ECHO MSG="Pressure advance tuning tower requires you to be printing gcode and on layer 1 to start."
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro CHAMBER_FILTER_ON]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	_CHAMBER_FILTER_TURN_ON
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro CHAMBER_FILTER_OFF]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Deactivating chamber filter..."
	_CHAMBER_FILTER_TURN_OFF
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set chamber_filter_enable_at = printer["gcode_macro RatOS"].chamber_filter_enable_at|default('after_print_start')|lower %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_ON" MSG="at: {at}, chamber_filter_enable: {chamber_filter_enable}, chamber_filter_enable_at: {chamber_filter_enable_at}, chamber_filter_speed: {chamber_filter_speed}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	{% if chamber_filter_enable_at == at %}
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	
	
	_CHAMBER_FILTER_TURN_ON AT={at}
	
	
	{% if chamber_filter_enable_at == "print_end" %}
	_LED_CHAMBER_FILTER_ON
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_OFF]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF" MSG="chamber_filter_enable: {chamber_filter_enable}, filter_disable_period: {filter_disable_period}, filter_disable_bed_temp: {filter_disable_bed_temp}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	
	{% if filter_disable_period > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting {filter_disable_period} seconds before turning chamber filter off..."
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION={filter_disable_period}
	{% endif %}
	
	
	{% if filter_disable_bed_temp > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting for bed temp to cool down to {filter_disable_bed_temp}°C to turn filter off..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM=0 MAXIMUM={filter_disable_bed_temp}
	_CHAMBER_FILTER_TURN_OFF
	_LED_CHAMBER_FILTER_OFF
	{% endif %}
	
	{% endif %}

[delayed_gcode _CHAMBER_FILTER_OFF_TIMER]
gcode = 
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF_TIMER" MSG="executed"
	
	
	_CHAMBER_FILTER_TURN_OFF
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Chamber filter turned off!"
	
	
	_LED_CHAMBER_FILTER_OFF

[gcode_macro _CHAMBER_FILTER_TURN_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_speed|default(0)|float %}
	{% if at == "print_end" %}
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_disable_speed|default(0)|float %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION=0
	
	
	SET_FAN_SPEED FAN=filter SPEED={chamber_filter_speed}

[gcode_macro _CHAMBER_FILTER_TURN_OFF]
gcode = 
	
	SET_FAN_SPEED FAN=filter SPEED=0

[gcode_macro _CHAMBER_FILTER_SANITY_CHECK]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	{% if filter_disable_bed_temp > 0 and filter_disable_period > 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable, not both.")}
	{% endif %}
	
	{% if filter_disable_bed_temp == 0 and filter_disable_period == 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable.")}
	{% endif %}
	
	{% endif %}

[gcode_macro CHAMBER_HEATER_ON]
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(45)|int %}
	
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp} IS_FROM_START_PRINT=False

[gcode_macro CHAMBER_HEATER_OFF]
gcode = 
	_CHAMBER_HEATER_OFF

[gcode_macro _CHAMBER_HEATER_ON]
variable_chamber_temp = 0
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	{% set is_from_start_print = true if params.IS_FROM_START_PRINT|default(True)|lower == 'true' else false %}
	
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set chamber_heater_enable = true if printer["gcode_macro RatOS"].chamber_heater_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}
	{% set chamber_heater_preheating_temp = printer["gcode_macro RatOS"].chamber_heater_preheating_temp|default(150)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	{% set chamber_heater_control_external_heater = true if printer["gcode_macro RatOS"].chamber_heater_control_external_heater|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_enable = true if printer["gcode_macro RatOS"].chamber_heater_air_circulation_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_fan_speed = printer["gcode_macro RatOS"].chamber_heater_air_circulation_fan_speed|default(0.35)|float %}
	{% set chamber_heater_air_circulation_y_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_y_pos|default(0)|float %}
	{% set chamber_heater_air_circulation_z_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_z_pos|default(100)|float %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_HEATER_ON" MSG="chamber_heater_enable: {chamber_heater_enable}, chamber_heater_preheating_temp: {chamber_heater_preheating_temp}, chamber_heater_heating_temp_offset: {chamber_heater_heating_temp_offset}, bed_temp: {bed_temp}, chamber_temp: {chamber_temp}, start_chamber_temp: {start_chamber_temp}"
	
	
	{% if chamber_heater_enable and chamber_temp > 0 and chamber_heater_bed_temp > 0 %}
	
	
	_LED_HEATING
	
	
	RATOS_ECHO MSG="Preheating chamber to {(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}°C..."
	
	
	{% set chamber_temp_sensor = "extruder" %}
	{% if printer["dual_carriage"] is defined and default_toolhead == 1 %}
	{% set chamber_temp_sensor = "extruder1" %}
	{% endif %}
	{% if printer["temperature_sensor chamber"] is defined %}
	{% set chamber_temp_sensor = "temperature_sensor chamber" %}
	{% endif %}
	
	
	{% set current_chamber_temp = printer['%s' % chamber_temp_sensor].temperature|int %}
	
	
	{% set needs_heating = current_chamber_temp < (start_chamber_temp if start_chamber_temp > 0 else chamber_temp) %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_BEFORE_PREHEATING
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	{% if not is_from_start_print %}
	MAYBE_HOME
	{% endif %}
	G0 Z{chamber_heater_air_circulation_z_pos} F{z_speed}
	G0 Y{chamber_heater_air_circulation_y_pos} F{speed}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * chamber_heater_air_circulation_fan_speed)}
	{% endif %}
	{% else %}
	{% if is_from_start_print %}
	G0 Z{z} F{z_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE={chamber_temp}
	
	
	{% if needs_heating %}
	
	
	M140 S{chamber_heater_bed_temp}
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={chamber_heater_preheating_temp}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	
	{% endif %}
	
	
	{% if needs_heating %}
	_CHAMBER_HEATER_EXTRA_FAN_ON
	{% endif %}
	
	
	{% if needs_heating %}
	TEMPERATURE_WAIT SENSOR="{chamber_temp_sensor}" MINIMUM={(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% endif %}
	
	
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED=0
	_CHAMBER_FILTER_ON AT="before_print_start"
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	G28 Z
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_AFTER_PREHEATING
	{% endif %}
	
	
	{% if printer["temperature_sensor chamber"] is defined %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined and chamber_heater_control_external_heater %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	
	
	_LED_SUCCESS
	
	{% endif %}

[gcode_macro _CHAMBER_HEATER_OFF]
gcode = 
	RATOS_ECHO MSG="Deactivating chamber heater..."
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=0
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE=0
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	
	
	_CHAMBER_HEATER_EXTRA_FAN_OFF

[delayed_gcode _CHAMBER_HEATER_CONTROL]
initial_duration = 0.
gcode = 
	
	{% set chamber_temp = printer["gcode_macro _CHAMBER_HEATER_ON"].chamber_temp|default(0)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	
	
	{% set current_chamber_temp = printer['temperature_sensor chamber'].temperature|int %}
	
	
	{% if current_chamber_temp < chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	{% endif %}
	
	
	{% if current_chamber_temp >= chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_ON]
gcode = 
	
	{% set chamber_heater_extra_fan_speed = printer["gcode_macro RatOS"].chamber_heater_extra_fan_speed|default(0.0)|float %}
	
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	{% if chamber_heater_extra_fan_speed > 0 %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED={chamber_heater_extra_fan_speed}
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_OFF]
gcode = 
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED=0
	{% endif %}

[gcode_macro _USER_CHAMBER_HEATER_BEFORE_PREHEATING]
description = Will be executed before chamber preheating, only if heating is needed.
gcode = 

[gcode_macro _USER_CHAMBER_HEATER_AFTER_PREHEATING]
description = Will be executed after chamber preheating, only if heating was needed.
gcode = 

[gcode_macro RESET_HEATSOAK_SETTINGS]
description = Resets all heatsoak-related settings to startup defaults
gcode = 
	HEATSOAK_SETTINGS ACTION=reset

[gcode_macro USE_ADAPTIVE_HEATSOAK]
description = Temporarily enables adaptive bed heatsoaking (if a beacon probe is present), will reset to printer.cfg settings
	when Klipper is restarted. Optionally specify QUALITY (1-5) and maximum FIRST_LAYER_DURATION (in minutes).
	Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.QUALITY|default("1..5") %}
	{% set _ = params.FIRST_LAYER_DURATION|default("1..120 minutes") %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("Adaptive heatsoaking is only available when a beacon probe is configured.") }
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_quality = (settings.variable_beacon_adaptive_heat_soak_layer_quality if defsrc == 'startup' else current.beacon_adaptive_heat_soak_layer_quality)|default(3)|int %}
	{% set default_first_layer_duration_secs = (settings.variable_beacon_adaptive_heat_soak_maximum_first_layer_duration if defsrc == 'startup' else current.beacon_adaptive_heat_soak_maximum_first_layer_duration)|default(1800)|int %}
	{% if params2.QUALITY is defined %}
	{% set quality = params2.QUALITY|int %}
	{% if quality < 1 or quality > 5 %}
	{ action_raise_error("QUALITY must be between 1 (rough) and 5 (maximum). Use 3 (normal) if unsure.") }
	{% endif %}
	{% else %}
	{% set quality = default_quality %}
	{% endif %}
	{% if params2.FIRST_LAYER_DURATION is defined %}
	{% set first_layer_duration_mins = params2.FIRST_LAYER_DURATION|float %}
	{% if first_layer_duration_mins <= 0 %}
	{ action_raise_error("FIRST_LAYER_DURATION must be a positive number specifying the maximum first layer duration in minutes.") }
	{% endif %}
	{% if first_layer_duration_mins > 120 %}
	CONSOLE_ECHO MSG="FIRST_LAYER_DURATION will be limited to 120 minutes. Values larger than this will not have an effect on soak time."
	{% set first_layer_duration_mins = 120 %}
	{% endif %}
	{% set first_layer_duration_secs = (first_layer_duration_mins * 60.0)|int %}
	{% else %}
	{% set first_layer_duration_secs = default_first_layer_duration_secs %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	{% endif %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=True beacon_adaptive_heat_soak_layer_quality={quality} beacon_adaptive_heat_soak_maximum_first_layer_duration={first_layer_duration_secs}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."

[gcode_macro USE_FIXED_HEATSOAK]
description = Temporarily enables fixed bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
	Optionally specify DURATION (in minutes). Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.DURATION|default("0..720 minutes") %}
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_duration = (settings.variable_bed_heat_soak_time if defsrc == 'startup' else current.bed_heat_soak_time)|default(0)|int %}
	{% if params2.DURATION is defined %}
	{% set duration_mins = params2.DURATION|float %}
	{% if duration_mins < 0 %}
	{ action_raise_error("DURATION must be a non-negative number specifying the heatsoak duration in minutes.") }
	{% endif %}
	{% if duration_mins > 720 %}
	CONSOLE_ECHO MSG="DURATION will be limited to 720 minutes (12 hours). If you really need a larger value, adjust printer.cfg instead."
	{% set duration_mins = 720 %}
	{% endif %}
	{% set duration_secs = (duration_mins * 60.0)|int %}
	{% else %}
	{% set duration_secs = default_duration %}
	{% set duration_mins = duration_secs / 60.0 %}
	{% endif %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% if has_beacon %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=False bed_heat_soak_time={duration_secs}
	{% else %}
	HEATSOAK_SETTINGS QUIET=1 bed_heat_soak_time={duration_secs}
	{% endif %}
	{% if duration_mins < 1e-3 %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% else %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% endif %}

[gcode_macro USE_NO_HEATSOAK]
description = Temporarily disables bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
gcode = 
	USE_FIXED_HEATSOAK DURATION=0

[gcode_macro HEATSOAK_SETTINGS]
description = Shows or adjusts heatsoak settings
	- With no arguments: shows current heatsoak settings, specify VERBOSE=1 for detailed output
	- With arguments: sets the specified settings. Use the full setting name without the variable_ prefix, e.g. bed_heat_soak_time=300 or beacon_adaptive_heat_soak_layer_quality=4. See printer.cfg for available settings.
variable_default_source = "startup"
gcode = 
	
	{% set params2 = params %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% set quiet = params2.pop("QUIET", None)|default("0") in ("1", "true", "yes") %}
	{% set verbose = params2.pop("VERBOSE", None)|default("0") in ("1", "true", "yes") %}
	{% if has_beacon %}
	{% set vars = (
	"beacon_adaptive_heat_soak",
	"beacon_adaptive_heat_soak_max_wait",
	"beacon_adaptive_heat_soak_extra_wait_after_completion",
	"beacon_adaptive_heat_soak_layer_quality",
	"beacon_adaptive_heat_soak_maximum_first_layer_duration",
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% else %}
	{% set vars = (
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% endif %}
	{% set action = "show" if params|length == 0 else params2.ACTION %}
	{% if action is defined and params|length > 1 %}
	{ action_raise_error("ACTION cannot be specified with other parameters.") }
	{% elif action is not defined %}
	{% for k, v in params2.items() %}
	{% set k = k|lower %}
	{% if k in vars %}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Setting {k} to {v}"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={k} VALUE={v}
	{% else %}
	{ action_raise_error("Parameter '%s' is not recognised. Note that adaptive heatsoaking settings can only be set when a beacon probe is configured." % k) }
	{% endif %}
	{% endfor %}
	{% elif action == "reset" %}
	_RESET_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	CONSOLE_ECHO MSG="Heatsoak settings have been reset to their original values."
	{% elif action == "show" %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% set is_adaptive = False if not has_beacon else current.beacon_adaptive_heat_soak|default("")|lower == "true" %}
	{% if is_adaptive %}
	{% set quality = current.beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set first_layer_duration_secs = current.beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."
	{% elif current.bed_heat_soak_time|default(0)|int > 0 %}
	{% set duration_mins = (current.bed_heat_soak_time|int / 60.0) %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% else %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% endif %}
	{% if verbose %}
	CONSOLE_ECHO MSG="Detailed settings:"
	_SHOW_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	{% endif %}
	{% else %}
	{ action_raise_error("Action '%s' is not recognised" % action) }
	{% endif %}

[gcode_macro _LED_START_PRINTING]
gcode = 
	_LED_ACTION

[gcode_macro _LED_START_PRINTING_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_PRINTING]
gcode = 
	_LED_ON TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_PAUSE]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_ON]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_OFF]
gcode = 
	_LED_STANDBY

[gcode_macro _LED_LOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_LOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_RUNOUT]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_CLOG]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_UNLOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_UNLOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_DEACTIVATE_TOOLHEAD]
gcode = 
	_LED_OFF TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_STANDBY]
gcode = 
	_LED_STANDBY TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_WAKEUP]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_MOTORS_OFF]
gcode = 
	_LED_STANDBY
	_LED_VAOC_OFF

[gcode_macro _LED_INPUT_SHAPER_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_INPUT_SHAPER_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_BEACON_CALIBRATION_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_VAOC_ON]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=1.0 GREEN=1.0 BLUE=1.0
	{% endif %}

[gcode_macro _LED_VAOC_OFF]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=0.0 GREEN=0.0 BLUE=0.0
	{% endif %}

[gcode_macro _LED_ACTION]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_action %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SUCCESS]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_success %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_HEATING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_heating %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_COOLING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_cooling %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ERROR]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_error %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ON]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_on %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_OFF]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_off %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_STANDBY]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_standby %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}
	
	{% if toolhead >= 0 %}
	{% if printer['neopixel nozzle_led_t%s' % toolhead] is defined  %}
	SET_LED LED={'nozzle_led_t%s' % toolhead} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% else %}
	{% if printer['neopixel nozzle_led_t0'] is defined  %}
	SET_LED LED={'nozzle_led_t0'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% if printer['neopixel nozzle_led_t1'] is defined %}
	SET_LED LED={'nozzle_led_t1'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% endif %}
	
	_USER_LED_SET { rawparams }

[gcode_macro _USER_LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}

[gcode_macro LOAD_FILAMENT]
description = Loads new filament. Note: be careful with PETG, make sure you inspect the tip of your filament before loading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% if filament_name == '' or filament_type == '' %}
	{% set filament_name = 'unknown' %}
	{% set filament_type = 'unknown' %}
	{% endif %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_LOAD_FILAMENT TEMP={temp} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_LOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_LOAD_FILAMENT]
description = Load filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_LOAD_FILAMENT" MSG="TEMP={temp}"
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=load_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	_LOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	
	
	RESTORE_GCODE_STATE NAME=load_state
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament load routine complete, please check that the filament was loaded correctly."

[gcode_macro _IDEX_LOAD_FILAMENT]
description = Load filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament into T{toolhead}..."
	
	DEBUG_ECHO PREFIX="_IDEX_LOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	_LOAD_FILAMENT TOOLHEAD={toolhead} TEMP={temp} AUTOMATED={automated}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="Filament load routine for T{toolhead} complete, please check that the filament was loaded correctly."

[gcode_macro _LOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default(false)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE TOOLHEAD={toolhead}
	_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into hotend.."
	G92 E0
	G0 E{extruder_gear_to_cooling_position_distance} F{extruder_load_speed}
	G92 E0
	M400
	RATOS_ECHO MSG="Filament loaded into hotend."

[gcode_macro _LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set load_speed = printer["gcode_macro T%s" % toolhead].filament_load_speed|float * 60 %}
	{% set filament_loading_nozzle_offset = printer["gcode_macro T%s" % toolhead].filament_loading_nozzle_offset|float %}
	{% set cooling_position_to_nozzle_distance = printer["gcode_macro T%s" % toolhead].cooling_position_to_nozzle_distance|float %}
	{% set purge_after_load = printer["gcode_macro T%s" % toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into nozzle... Please wait!"
	G92 E0
	
	G0 E{cooling_position_to_nozzle_distance + filament_loading_nozzle_offset} F{load_speed}
	G92 E0
	G4 P1000
	_PURGE_FILAMENT	TOOLHEAD={toolhead} E={purge_after_load}
	RATOS_ECHO MSG="Filament loaded into nozzle!"

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"
	
	
	{% set filament_grabbing_length = printer["gcode_macro T%s" % toolhead].filament_grabbing_length|float %}
	{% set filament_grabbing_speed = printer["gcode_macro T%s" % toolhead].filament_grabbing_speed|float %}
	{% set resume_after_insert = true if printer["gcode_macro T%s" % toolhead].resume_after_insert|default(true)|lower == 'true' else false %}
	{% set enable_insert_detection = true if printer["gcode_macro T%s" % toolhead].enable_insert_detection|default(true)|lower == 'true' else false %}
	
	
	{% set current_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	
	{% if enable_insert_detection %}
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="toolhead: {toolhead}, filament_grabbing_length: {filament_grabbing_length}, filament_grabbing_speed: {filament_grabbing_speed}, current_idex_mode: {current_idex_mode}"
	
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	RATOS_ECHO MSG="Filament inserted into T{toolhead}, loading..."
	
	
	FORCE_MOVE STEPPER={'extruder%s' % ('' if toolhead == 0 else toolhead)} DISTANCE={filament_grabbing_length} VELOCITY={filament_grabbing_speed}
	M400
	
	
	{% if printer.pause_resume.is_paused %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% if resume_after_insert %}
	RESUME
	{% endif %}
	{% else %}
	{% if not printer.virtual_sdcard.is_active %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"

[gcode_macro _PURGE_BEFORE_UNLOAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set purge_before_unload = printer["gcode_macro T%s" % toolhead].purge_before_unload|float %}
	
	DEBUG_ECHO PREFIX="_PURGE_BEFORE_UNLOAD" MSG="TOOLHEAD: {toolhead}"
	
	
	{% if purge_before_unload > 0 %}
	G92 E0
	G0 E{purge_before_unload} F300
	G92 E0
	M400
	{% endif %}

[gcode_macro _PURGE_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set e = params.E|int %}
	{% set r = params.R|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_PURGE_FILAMENT" MSG="TOOLHEAD: {toolhead}, E: {e}"
	
	
	{% if e > 0 %}
	
	
	G92 E0
	G0 E{e} F300
	G92 E0
	M400
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={0.4 if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={0.4 if toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * 0.4)}
	{% endif %}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if r > 0 %}
	G92 E0
	G0 E-{r} F300
	G92 E0
	M400
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro _MOVE_TO_LOADING_POSITION]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_MOVE_TO_LOADING_POSITION" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	
	G1 X{loading_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _CLEANING_MOVE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_CLEANING_MOVE" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].parking_position is defined and printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set parking_position = printer["gcode_macro T%s" % toolhead].parking_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	{% set cleaning_position = loading_position %}
	{% if loading_position == parking_position %}
	{% if loading_position > 0 %}
	{% set cleaning_position = loading_position - 30 %}
	{% else %}
	{% set cleaning_position = loading_position + 30 %}
	{% endif %}
	{% endif %}
	
	
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _BED_MESH_SANITY_CHECK]
gcode = 
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is defined %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_start_print_true_zero_fuzzy_position %}
	CONSOLE_ECHO TYPE="error" TITLE="Defined zero reference not compatible with fuzzy true zero" MSG="Using fuzzy start print true zero position is not compatible with a defined zero_reference_position value in the [bed_mesh] section in printer.cfg._N_Please remove the zero_reference_position value from the [bed_mesh] section, or disable fuzzy true zero position in printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_start_print_true_zero_fuzzy_position: False"
	_STOP_AND_RAISE_ERROR MSG="Defined zero reference not compatible with fuzzy true zero"
	{% elif zero_ref_pos[0]|float|round != safe_home_x|float|round or zero_ref_pos[1]|float|round != safe_home_y|float|round %}
	CONSOLE_ECHO TYPE="error" TITLE="Zero reference position does not match safe home position" MSG="Please update your bed mesh zero reference position in printer.cfg, like so:_N__N_[bed_mesh]_N_zero_reference_position: {safe_home_x|float|round},{safe_home_y|float|round}_N_"
	_STOP_AND_RAISE_ERROR MSG="Zero reference position does not match safe home position"
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_bed_mesh %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact bed mesh is enabled" MSG="Beacon contact bed mesh is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_bed_mesh: False"
	{% endif %}
	
	{% if beacon_scan_method_automatic %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon 'automatic' scan method is enabled" MSG="Beacon 'automatic' scan method is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_scan_method_automatic: False"
	{% endif %}
	
	{% if beacon_contact_z_tilt_adjust %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact z-tilt adjust is enabled" MSG="Beacon contact z-tilt adjust is enabled. This is not recommended for normal use and may result in inaccurate z-tilt adjustment._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_z_tilt_adjust: False"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH]
gcode = 
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE=None
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE=None
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION {rawparams}
	{% endif %}

[gcode_macro _START_PRINT_BED_MESH]
variable_actual_true_zero_position_x = None
variable_actual_true_zero_position_y = None
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set X=[params.X0|default(-1)|float, params.X1|default(-1)|float] %}
	{% set Y=[params.Y0|default(-1)|float, params.Y1|default(-1)|float] %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_BED_MESH" MSG="idex_mode: {idex_mode}, X: {X}, Y: {Y}"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is not defined %}
	{% set zero_ref_pos = [safe_home_x if actual_true_zero_position_x is none else actual_true_zero_position_x, safe_home_y if actual_true_zero_position_y is none else actual_true_zero_position_y] %}
	{% endif %}
	
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	
	
	
	
	{% set X=[0, printable_x_max] %}
	{% endif %}
	
	
	{% set beacon_bed_mesh_scv = printer["gcode_macro RatOS"].beacon_bed_mesh_scv|default(25)|int %}
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% if printer.fastconfig.settings.beacon is defined and not beacon_contact_bed_mesh %}
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={beacon_bed_mesh_scv}
	{% endif %}
	
	
	{% set default_profile = printer["gcode_macro RatOS"].bed_mesh_profile|default('ratos') %}
	{% if printer["gcode_macro RatOS"].calibrate_bed_mesh|lower == 'true' %}
	BED_MESH_CLEAR
	{% if printer["gcode_macro RatOS"].adaptive_mesh|lower == 'true' %}
	CALIBRATE_ADAPTIVE_MESH PROFILE="{default_profile}" X0={X[0]} X1={X[1]} Y0={Y[0]} Y1={Y[1]} T={params.T|int} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={idex_mode} ZERO_REF_POS_X={zero_ref_pos[0]} ZERO_REF_POS_Y={zero_ref_pos[1]}
	{% else %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	BED_MESH_PROFILE LOAD="{default_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	
	{% elif printer["gcode_macro RatOS"].bed_mesh_profile is defined %}
	BED_MESH_CLEAR
	BED_MESH_PROFILE LOAD="{printer["gcode_macro RatOS"].bed_mesh_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"

[gcode_macro CALIBRATE_ADAPTIVE_MESH]
gcode = 
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set default_profile = params.PROFILE %}
	
	
	{% set x0 = params.X0|default(-1)|float %}
	{% set y0 = params.Y0|default(-1)|float %}
	{% set x1 = params.X1|default(-1)|float %}
	{% set y1 = params.Y1|default(-1)|float %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Received coordinates X0={x0|round(1)} Y0={y0|round(1)} X1={x1|round(1)} Y1={y1|round(1)}"
	
	{% if x0 >= x1 or y0 >= y1 %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Invalid coordinates received. Please check your slicer settings. Falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	
	
	{% if params.ZERO_REF_POS_X is defined and params.ZERO_REF_POS_Y is defined %}
	{% set zero_ref_pos_x = params.ZERO_REF_POS_X|float %}
	{% set zero_ref_pos_y = params.ZERO_REF_POS_Y|float %}
	{% if zero_ref_pos_x < x0 or zero_ref_pos_x > x1 or zero_ref_pos_y < y0 or zero_ref_pos_y > y1 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Zero reference position X={zero_ref_pos_x|round(1)} Y={zero_ref_pos_y|round(1)} is outside the mesh region, expanding mesh region to include it."
	{% set x0 = [x0, zero_ref_pos_x]|min %}
	{% set y0 = [y0, zero_ref_pos_y]|min %}
	{% set x1 = [x1, zero_ref_pos_x]|max %}
	{% set y1 = [y1, zero_ref_pos_y]|max %}
	{% endif %}
	{% endif %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float %}
	
	
	{% set mesh_x0 = [[x0, max_x]|min, min_x]|max %}
	{% set mesh_y0 = [[y0, max_y]|min, min_y]|max %}
	{% set mesh_x1 = [[x1, max_x]|min, min_x]|max %}
	{% set mesh_y1 = [[y1, max_y]|min, min_y]|max %}
	
	{% if mesh_x0 == min_x and mesh_y0 == min_y and mesh_x1 == max_x and mesh_y1 == max_y %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Print is using the full bed, falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	
	{% set probe_count_x = mesh_config.probe_count.split(",")[0]|int %}
	{% if mesh_config.probe_count.split(",")|length == 2 %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[1]|int %}
	{% else %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[0]|int %}
	{% endif %}
	
	
	{% set probe_x_step = (max_x - min_x) / probe_count_x %}
	{% set probe_y_step = (max_y - min_y) / probe_count_y %}
	
	
	{% set mesh_count_x = ([(mesh_x1 - mesh_x0) / probe_x_step, 3]|max)|int %}
	{% set mesh_count_y = ([(mesh_y1 - mesh_y0) / probe_y_step, 3]|max)|int %}
	{% set min_mesh_count = [mesh_count_x, mesh_count_y]|min %}
	{% set max_mesh_count = [mesh_count_x, mesh_count_y]|max %}
	
	
	{% set algorithm = mesh_config.algorithm %}
	{% if algorithm|lower == 'lagrange' and max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="cannot exceed a probe_count of 6 when using lagrange interpolation. Falling back to bicubic interpolation."
	{% set algorithm = 'bicubic' %}
	{% endif %}
	{% if algorithm|lower == 'bicubic' and min_mesh_count < 4 %}
	{% if max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="invalid probe_count option when using bicubic interpolation. Combination of 3 points on one axis with more than 6 on another is not permitted. Forcing minimum mesh count to be 4."
	{% set min_mesh_count = 4 %}
	{% else %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="bicubic interpolation with a probe_count of less than 4 points detected. Forcing lagrange interpolation."
	{% set algorithm = 'lagrange' %}
	{% endif %}
	{% endif %}
	
	{% set mesh_count_x = ([min_mesh_count, mesh_count_x]|max)|int %}
	{% set mesh_count_x = ([max_mesh_count, mesh_count_x]|min)|int %}
	{% set mesh_count_y = ([min_mesh_count, mesh_count_y]|max)|int %}
	{% set mesh_count_y = ([max_mesh_count, mesh_count_y]|min)|int %}
	
	{% set should_prime = printer["gcode_macro RatOS"].nozzle_priming == 'primeblob' %}
	{% if printer["dual_carriage"] is not defined %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% else %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 != 0 and probe_first %}
	{% set probe_first = false %}
	{% elif printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 == 0 and not probe_first %}
	{% set probe_first = true %}
	{% endif %}
	
	
	{% if should_prime and probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="mesh coordinates X0={mesh_x0|round(1)} Y0={mesh_y0|round(1)} X1={mesh_x1|round(1)} Y1={mesh_y1|round(1)}"
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y} RELATIVE_REFERENCE_INDEX=-1
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	
	
	{% if should_prime and not probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro M84]
rename_existing = M84.1
gcode = 
	
	M84.1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_OFFSET X=0 Y=0
	
	
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro _VAOC"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False
	{% endif %}
	
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	SET_SKEW CLEAR=1
	
	
	_LED_MOTORS_OFF

[gcode_macro M104]
rename_existing = M104.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M104" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set temperature_offset_t0 = printer["gcode_macro T0"].temperature_offset|default(0)|int %}
	{% set temperature_offset_t1 = printer["gcode_macro T1"].temperature_offset|default(0)|int %}
	{% set s0 = [s + temperature_offset_t0, 0]|max %}
	{% set s1 = [s + temperature_offset_t1, 0]|max %}
	{% if temperature_offset_t0 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t0}°C added to toolhead T0."
	{% endif %}
	{% if temperature_offset_t1 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t1}°C added to toolhead T1."
	{% endif %}
	{% else %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	M104.1 S{s0} T0
	M104.1 S{s1} T1
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% else %}
	M104.1 S{s} T{t}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M109]
rename_existing = M109.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M109" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M109" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	M109.1 S{s} T{t}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro SET_HEATER_TEMPERATURE]
rename_existing = SET_HEATER_TEMPERATURE_BASE
gcode = 
	
	{% set heater = params.HEATER|default("") %}
	{% set target = params.TARGET|default(0)|int %}
	
	DEBUG_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="heater: {heater}, target: {target}"
	
	{% set t = -1 %}
	{% if heater|lower == "extruder" or heater|lower == "extruder1" %}
	
	{% set t = 0 if heater|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and target > 0 %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set target = [target + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE_BASE HEATER="{heater}" TARGET={target}
	
	{% if t != -1 and printer.fastconfig.settings.beacon is defined %}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro TEMPERATURE_WAIT]
rename_existing = TEMPERATURE_WAIT_BASE
gcode = 
	
	{% set sensor = params.SENSOR|default("") %}
	{% set minimum = params.MINIMUM|default(-1)|int %}
	{% set maximum = params.MAXIMUM|default(-1)|int %}
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="sensor: {sensor}, minimum: {minimum}, maximum: {maximum}"
	
	{% set t = -1 %}
	{% if sensor|lower == "extruder" or sensor|lower == "extruder1" %}
	
	{% set t = 0 if sensor|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and (minimum > 0 or maximum > 0) %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% if minimum > -1 %}
	{% set minimum = [minimum + temperature_offset, 0]|max %}
	{% endif %}
	{% if maximum > -1 %}
	{% set maximum = [maximum + temperature_offset, 0]|max %}
	{% endif %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set id = "sensor " ~ sensor if t == -1 else "toolhead T" ~ t %}
	
	
	{% if minimum > -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum} MAXIMUM={maximum}
	{% elif minimum > -1 and maximum == -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum}
	{% elif minimum == -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MAXIMUM={maximum}
	{% else %}
	
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="neither MINIMUM or MAXIMUM args were specified, call TEMPERATURE_WAIT_BASE is expected to fail"
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}"
	{% endif %}
	
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature for {id} reached."

[gcode_macro SDCARD_PRINT_FILE]
rename_existing = SDCARD_PRINT_FILE_BASE
gcode = 
	{% if printer["ratos"] is defined %}
	PROCESS_GCODE_FILE { rawparams }
	{% else %}
	SDCARD_PRINT_FILE_BASE { rawparams }
	{% endif %}

[gcode_macro SKEW_PROFILE]
rename_existing = SKEW_PROFILE_BASE
variable_loaded_profile = ""
gcode = 
	{% if params.LOAD is defined %}
	{% if printer.fastconfig.settings["skew_correction %s" % params.LOAD] is defined %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='"{params.LOAD}"'
	{% endif %}
	{% endif %}
	
	SKEW_PROFILE_BASE { rawparams }

[gcode_macro SET_SKEW]
rename_existing = SET_SKEW_BASE
gcode = 
	{% if params.CLEAR is defined %}
	{% if params.CLEAR|default(0)|int == 1 %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='""'
	{% endif %}
	{% endif %}
	
	SET_SKEW_BASE { rawparams }

[gcode_macro SET_VELOCITY_LIMIT]
rename_existing = SET_VELOCITY_LIMIT_BASE
gcode = 
	{% if params.ACCEL_TO_DECEL is defined %}
	
	{% if params.ACCEL is defined %}
	{% set accel = params.ACCEL|float %}
	{% else %}
	{% set accel = printer.toolhead.max_accel|float %}
	{% endif %}
	
	{% if params.VELOCITY is defined %}
	{% set velocity = params.VELOCITY|float %}
	{% else %}
	{% set velocity = printer.toolhead.max_velocity|float %}
	{% endif %}
	
	{% if params.SQUARE_CORNER_VELOCITY is defined %}
	{% set scv = params.SQUARE_CORNER_VELOCITY|float %}
	{% else %}
	{% set scv = printer.toolhead.square_corner_velocity|float %}
	{% endif %}
	
	{% set mcr = params.ACCEL_TO_DECEL|float / accel %}
	
	DEBUG_ECHO PREFIX="SET_VELOCITY_LIMIT" MSG="ACCEL={accel}, VELOCITY={velocity}, SQUARE_CORNER_VELOCITY={scv}, MINIMUM_CRUISE_RATIO={mcr}"
	
	SET_VELOCITY_LIMIT_BASE ACCEL={accel} VELOCITY={velocity} SQUARE_CORNER_VELOCITY={scv} MINIMUM_CRUISE_RATIO={1-mcr}
	
	{% else %}
	
	SET_VELOCITY_LIMIT_BASE { rawparams }
	
	{% endif %}

[gcode_macro BED_MESH_CALIBRATE]
rename_existing = _BED_MESH_CALIBRATE_BASE
variable_abl_and_home_z_if_required = True
gcode = 
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	{% if abl_and_home_z_if_required %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% endif %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set beacon_default_probe_method = printer.fastconfig.settings.beacon.default_probe_method|default('proximity') %}
	{% set probe_method = params.PROBE_METHOD|default(beacon_default_probe_method)|lower %}
	{% if probe_method == 'proximity' %}
	_CHECK_ACTIVE_BEACON_MODEL_TEMP TITLE="Bed mesh calibration warning"
	{% endif %}
	{% endif %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_BED_MESH_CALIBRATE_BASE {rawparams}
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	_APPLY_RATOS_BED_MESH_PARAMETERS {rawparams}
	{% endif %}

[gcode_macro SET_GCODE_OFFSET]
rename_existing = SET_GCODE_OFFSET_BASE
gcode = 
	DEBUG_ECHO PREFIX="SET_GCODE_OFFSET" MSG="{rawparams|replace('"', '')|replace("'", '')}"
	{% set z_before = printer.gcode_move.homing_origin.z|float %}
	SET_GCODE_OFFSET_BASE {rawparams}
	_AFTER_SET_GCODE_OFFSET Z_BEFORE={z_before}

[gcode_macro _AFTER_SET_GCODE_OFFSET]
gcode = 
	{% set z_before = params.Z_BEFORE|float %}
	{% set z_after = printer.gcode_move.homing_origin.z|float %}
	{% if z_before != z_after %}
	_ALERT_NON_ZERO_Z_OFFSET FORCE=1
	{% endif %}

[gcode_macro _START_PRINT_PARK]
gcode = 
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_x = printer["gcode_macro RatOS"].start_print_park_x %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% if printer["gcode_macro RatOS"].start_print_park_x is defined and printer["gcode_macro RatOS"].start_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="start_print_park_x is ignored for IDEX printers"
	{% endif %}
	PARK_TOOLHEAD
	G90
	{% endif %}
	
	
	_PARK LOCATION={start_print_park_in} X={start_print_park_x}
	G0 Z{z} F{z_speed}

[gcode_macro _END_PRINT_PARK]
gcode = 
	{% if printer["dual_carriage"] is defined %}
	
	{% if printer["gcode_macro RatOS"].end_print_park_x is defined and printer["gcode_macro RatOS"].end_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="end_print_park_x is ignored for IDEX printers"
	{% endif %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	PARK_TOOLHEAD
	G90
	{% endif %}
	_PARK LOCATION={printer["gcode_macro RatOS"].end_print_park_in} X={printer["gcode_macro RatOS"].end_print_park_x}

[gcode_macro _PARK]
gcode = 
	
	{% set x = params.X %}
	{% set location = params.LOCATION|default('back')|lower %}
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	{% set nozzle_priming = printer["gcode_macro RatOS"].nozzle_priming|lower %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="park"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% if x != '' %}
	{% if x|float >= printer.toolhead.axis_minimum.x + 5 and x|float <= printable_x_max - 5 %}
	{% set park_x = x|float %}
	{% else %}
	{action_respond_info('The requested X co-ordinate is outside the defined axis bounds - using defaults')}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	{% else %}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	
	
	{% set park_y = printable_y_max - 15 %}
	{% if location == 'front' %}
	{% set park_y = printer.toolhead.axis_minimum.y + 5 %}
	{% elif location == 'center' %}
	{% set park_y = printable_y_max / 2 %}
	{% elif location == 'primeblob' and printer["dual_carriage"] is defined %}
	
	{% set park_y = printable_y_max - 15 %}
	{% endif %}
	
	
	{% if location == 'primeblob' and printer["dual_carriage"] is not defined %}
	{% if (nozzle_priming == 'primeblob' or nozzle_priming == 'primeline') %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set park_x = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set park_x = printable_x_max - 5 %}
	{% else %}
	{% set park_x = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set park_y = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set park_y = printable_y_max - 5 %}
	{% else %}
	{% set park_y = nozzle_prime_start_y|float %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	G0 X{park_x} Y{park_y} F{speed}
	{% else %}
	
	G0 Y{park_y} F{speed}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="park"

[gcode_macro SAVE_PROBE_RESULT]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	{% set last_z_offset = 9999.9 %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if beacon_contact_prime_probing %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	{% else %}
	{% set last_z_offset = printer.beacon.last_sample.dist - current_z %}
	{% endif %}
	{% elif printer.fastconfig.settings.bltouch is defined  %}
	{% set config_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% elif printer.fastconfig.settings.probe is defined  %}
	{% set config_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% endif %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Saving offset adjustment of {last_z_offset} in {params.VARIABLE|default('last_z_offset')}"
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={params.VARIABLE|default('last_z_offset')} VALUE={last_z_offset}

[gcode_macro PROBE_FOR_PRIMING]
gcode = 
	
	{% set probe_for_priming_disable_mesh_constraints = true if printer["gcode_macro RatOS"].probe_for_priming_disable_mesh_constraints|default(false)|lower == 'true' else false %}
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower != 'false' %}
	SAVE_GCODE_STATE NAME=probe_for_priming_state
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the prime location.."
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set t = params.TOOLHEAD|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% if idex_mode == '' %}
	
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% if t == 0 %}
	{% set x_start = 5 %}
	{% else %}
	{% set x_start = printable_x_max - 5 %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% endif %}
	{% endif %}
	{% set z = printer.fastconfig.settings.bed_mesh.horizontal_move_z|float %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% if printer.fastconfig.settings.bltouch is defined %}
	{% set x_offset = printer.fastconfig.settings.bltouch.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.bltouch.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% elif printer.fastconfig.settings.probe is defined %}
	{% set x_offset = printer.fastconfig.settings.probe.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.probe.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% elif printer.fastconfig.settings.beacon is defined %}
	{% set x_offset = printer.fastconfig.settings.beacon.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.beacon.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.beacon.trigger_distance|float %}
	{% else %}
	{ action_raise_error("No probe, beacon or bltouch section found. Adaptive priming only works with a [probe], [beacon] or [bltouch] section defined.") }
	{% endif %}
	
	{% if z < z_offset %}
	{ action_raise_error("Horizontal move Z ({z}) is below your probe's Z offset ({z_offset}). Please adjust your horizontal_move_z setting in [bed_mesh] to be above {z}.") }
	{% endif %}
	
	{% if not probe_for_priming_disable_mesh_constraints %}
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float - x_offset %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float - y_offset %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float - x_offset %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float - y_offset %}
	
	
	{% set x_start = [[x_start, max_x]|min, min_x]|max %}
	{% set y_start = [[y_start, max_y]|min, min_y]|max %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the start of the prime location at {x_start}, {y_start}"
	
	G90
	
	M83
	
	G0 Z{z} F{z_speed}
	
	G1 X{x_start} Y{y_start} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result
	{% endif %}
	
	{% if idex_mode == '' %}
	
	{% set x_end = x_start %}
	{% set y_end = y_start + 45 %}
	{% else %}
	
	{% if t==1 %}
	{% set x_end = x_start - 45 %}
	{% else %}
	{% set x_end = x_start + 45 %}
	{% endif %}
	{% set y_end = y_start %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the end of the prime location at {x_end}, {y_end}"
	G1 X{x_end} Y{y_end} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result
	{% endif %}
	
	RESTORE_GCODE_STATE NAME=probe_for_priming_state
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	{% endif %}

[gcode_macro RESET_PRIME_PROBE_STATE]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result VALUE=None
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result_t1 VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result_t1 VALUE=None
	{% endif %}

[gcode_macro PROBE_CURRENT_POSITION]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	SAVE_GCODE_STATE NAME=probe_current_position_state
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	ASSERT_PROBE_DEPLOYED
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_prime_probing %}
	PROBE PROBE_METHOD=contact SAMPLES=1
	{% else %}
	PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	BEACON_QUERY
	{% else %}
	
	RESTORE_GCODE_STATE NAME=probe_current_position_state MOVE=1 MOVE_SPEED={printer["gcode_macro RatOS"].macro_z_speed|float}
	{% endif %}

[gcode_macro PRIME_BLOB]
description = Prints a primeblob, used internally, if configured, as part of the START_PRINT macro.
variable_x_offset = 5
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="prime_blob"
	SET_MACRO_TRAVEL_SETTINGS
	
	RATOS_ECHO PREFIX="Priming" MSG="Priming nozzle with prime blob.."
	
	
	{% set current_toolhead = 0 %}
	
	
	{% set target_idex_mode = '' %}
	{% set extruder = 'extruder' %}
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE is defined %}
	{% set target_idex_mode = params.IDEX_MODE|default('')|lower %}
	{% else %}
	{ action_raise_error("IDEX_MODE parameter not found for PRIME_BLOB macro. This is likely a bug.") }
	{% endif %}
	RATOS_ECHO PREFIX="Priming" MSG="Priming in IDEX {target_idex_mode} mode.."
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set current_toolhead = 1 if current_idex_mode=='primary' else 0 %}
	{% set extruder = 'extruder1' if current_toolhead == 1 else 'extruder' %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	SAVE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set fan_speed = printer["gcode_macro RatOS"].nozzle_prime_bridge_fan|float %}
	{% set nozzle_diameter = printer.fastconfig.settings[extruder].nozzle_diameter|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set has_start_offset_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) != 9999.9 %}
	{% if printer["dual_carriage"] is defined %}
	{% set has_start_offset_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) != 9999.9 %}
	{% endif %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_z_height = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set nozzle_prime_direction = printer["gcode_macro RatOS"].nozzle_prime_direction|lower %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% if target_idex_mode == '' %}
	
	{% set x_factor = 0 %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% set y_factor = -1 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% if nozzle_prime_start_y|float < printable_y_max / 2 %}
	{% set y_factor = 1 %}
	{% else %}
	{% set y_factor = -1 %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_direction == 'forwards' %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_direction == 'backwards' %}
	{% set y_factor = -1 %}
	{% endif %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% else %}
	{% set z = start_print_park_z_height %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% set y_factor = 0 %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set x_start = center_x / 2 + 5 %}
	{% set x_factor = 1 %}
	{% else %}
	
	
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% if current_toolhead == 0 %}
	{% set x_start = 55 %}
	{% set x_factor = -1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 55 %}
	{% set x_factor = 1 %}
	{% endif %}
	{% else %}
	{% if current_toolhead == 0 %}
	{% set x_start = 5 %}
	{% set x_factor = 1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 5 %}
	{% set x_factor = -1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_x_max - 5 %}
	{% endif %}
	{% set z = 10 %}
	{% endif %}
	
	{% set start_z_offset = 0 %}
	{% set end_z_offset = 0 %}
	{% if has_start_offset_t0 %}
	{% set start_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) %}
	{% set end_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_end_result|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t0) ) }
	{% endif %}
	{% if end_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t0) )  }
	{% endif %}
	{% set start_z_offset = start_z_probe_result_t0 %}
	{% set end_z_offset = end_z_probe_result_t0 %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	{% if current_toolhead == 1 or both_toolheads or target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	{% if has_start_offset_t1 %}
	{% set start_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) %}
	{% set end_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_end_result_t1|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t1) ) }
	{% endif %}
	{% if end_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t1) ) }
	{% endif %}
	{% set start_z_offset = [start_z_offset, start_z_probe_result_t1]|max %}
	{% set end_z_offset = [end_z_offset, start_z_probe_result_t1]|max %}
	{% endif %}
	{% endif %}
	{% if target_idex_mode != 'copy' and target_idex_mode != 'mirror' %}
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% set original_start_z_offset = start_z_offset %}
	{% set original_end_z_offset = end_z_offset %}
	{% set start_z_offset = original_end_z_offset %}
	{% set end_z_offset = original_start_z_offset %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	DEBUG_ECHO PREFIX="PRIME_BLOB" MSG="x_start: {x_start}, y_start: {y_start}, x_factor: {x_factor}, y_factor: {y_factor}, z: {z}, start_z_offset: {start_z_offset}, end_z_offset: {end_z_offset}"
	
	
	G90
	
	M83
	RATOS_ECHO PREFIX="Priming" MSG="Lifting Z to {z}.."
	
	G0 Z{z} F{z_speed}
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% if start_print_park_in != 'primeblob' %}
	G1 X{x_start} F{speed}
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% endif %}
	{% else %}
	
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% if target_idex_mode=="copy" or target_idex_mode=="mirror" %}
	RATOS_ECHO PREFIX="Priming" MSG="Mirroring move to {x_start}, {y_start} along the edge of the print area.."
	
	_IDEX_MIRROR PRIMING=1
	{% else %}
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% endif %}
	G1 X{x_start} F{speed}
	{% endif %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Starting prime blob.."
	
	G1 Z{0.5 + start_z_offset} F{z_speed}
	
	G1 Y{y_start} F{speed}
	
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	
	M106 S{fan_speed}
	
	G1 Z5 F100 E5
	G92 E0
	RATOS_ECHO PREFIX="Priming" MSG="Bridging with {((fan_speed/255) * 100)|int}% fan speed.."
	
	G1 F3000 X{x_start + (15 * x_factor)} Y{y_start + (15 * y_factor)} E{1 / ((0.4 / nozzle_diameter) ** 2)}
	
	
	
	G1 F3000 X{x_start + (20 * x_factor)} Y{y_start + (20 * y_factor)} Z{3.8 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (34 * x_factor)} Y{y_start + (34 * y_factor)} Z{2.6 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (38 * x_factor)} Y{y_start + (38 * y_factor)} Z{1.4 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (42 * x_factor)} Y{y_start + (42 * y_factor)} Z{0.2 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	
	M106 S0
	
	G1 F3000 X{x_start + (46 * x_factor)} Y{y_start + (46 * y_factor)} Z{0.2 + end_z_offset} E0.6
	
	G1 F{speed} X{x_start + (50 * x_factor)} Y{y_start + (50 * y_factor)}
	
	
	{% if target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if target_idex_mode == "copy" %}
	{% if first_y >= 0 %}
	_IDEX_COPY DANCE=0 Y={first_y}
	{% else %}
	_IDEX_COPY DANCE=0 Y={params.Y1}
	{% endif %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	RESTORE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="prime_blob"
	
	
	G92 E0

[gcode_macro UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set temp = params.TEMP|default(220)|int %}
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_UNLOAD_FILAMENT TEMP={temp} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_UNLOAD_FILAMENT]
description = Unload filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_UNLOAD_FILAMENT" MSG="TEMP: {temp}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=unload_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	G4 P3000
	
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD=0 NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=unload_state
	
	
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament unloading completed"

[gcode_macro _IDEX_UNLOAD_FILAMENT]
description = Unload filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading T{toolhead} filament..."
	
	DEBUG_ECHO PREFIX="_IDEX_UNLOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} AUTOMATED={automated}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="T{toolhead} filament unloading completed"

[gcode_macro _UNLOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LEGACY_UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
gcode = 
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set unload_speed = 5 * 60 %}
	{% set unload_length = printer["gcode_macro RatOS"].filament_unload_length|float %}
	M117 Unloading filament...
	
	G0 E10 F300
	
	G0 E-5 F3600
	
	G4 P3000
	
	G0 E5 F6000
	
	G0 E-15 F6000
	
	G0 E-{unload_length} F{unload_speed}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}
	M117 Filament unloaded!
	RESPOND MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	RATOS_ECHO MSG="Unloading filament from nozzle to cooling zone... Please wait!"
	
	_PURGE_BEFORE_UNLOAD TOOLHEAD={toolhead}
	
	{% if printer["gcode_macro _UNLOAD_WITHOUT_TIP_FORMING"] is defined %}
	
	_UNLOAD_WITHOUT_TIP_FORMING TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	_UNLOAD_WITH_TIP_FORMING NAME='{filament_name}' TYPE='{filament_type}'
	{% endif %}
	
	G4 P3000

[gcode_macro _UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	{% set tooolhead_sensor_to_extruder_gear_distance = printer["gcode_macro T%s" % toolhead].tooolhead_sensor_to_extruder_gear_distance|float %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER" MSG="TOOLHEAD: {toolhead}"
	
	
	G0 E-{extruder_gear_to_cooling_position_distance + tooolhead_sensor_to_extruder_gear_distance + 50} F{extruder_load_speed}
	
	RATOS_ECHO MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_WITH_TIP_FORMING]
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	{% if filament_name != '' and filament_type != '' %}
	_UNLOAD_KNOWN_FILAMENT NAME={filament_name} TYPE={filament_type}
	{% else %}
	_UNLOAD_UNKNOWN_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _UNLOAD_KNOWN_FILAMENT]
description = User overrideable tip forming macro if slicer filament profiles are known
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	RATOS_ECHO PREFIX="FILAMENT TYPE" MSG='{filament_type}'
	RATOS_ECHO PREFIX="FILAMENT PROFILE" MSG='{filament_name}'
	
	
	{% if filament_name == "Prusament PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% elif filament_name == "Nobufil PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% else %}
	
	RATOS_ECHO PREFIX="_UNLOAD_KNOWN_FILAMENT" MSG="Filament profile not found!"
	_UNLOAD_UNKNOWN_FILAMENT
	{% endif %}

[gcode_macro _UNLOAD_UNKNOWN_FILAMENT]
description = User overrideable standard tip forming macro
gcode = 
	
	DEBUG_ECHO PREFIX="_UNLOAD_UNKNOWN_FILAMENT" MSG="Using standard tip forming macro!"
	
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10

[gcode_macro _TIP_FORMING]
gcode = 
	
	{% set cooling_moves = params.COOLING_MOVES|default(4)|int %}
	{% set cooling_move_length = params.COOLING_MOVE_LENGTH|default(10)|float %}
	{% set start_cooling_speed = params.START_COOLING_SPEED|default(10)|float * 60 %}
	{% set end_cooling_speed = params.END_COOLING_SPEED|default(50)|float * 60 %}
	{% if cooling_moves == 0 %}
	{% set cooling_move_length = 0 %}
	{% endif %}
	
	
	{% set dip = true if params.DIP|default(false)|lower == "true" else false %}
	{% set dip_length = params.DIP_LENGTH|default(22)|float %}
	{% set dip_speed = params.DIP_SPEED|default(30)|float * 60 %}
	{% set dip_retract_speed = params.DIP_RETRACT_SPEED|default(70)|float * 60 %}
	
	
	{% set retract_length = params.RETRACT_LENGTH|default(18)|float %}
	{% set start_retract_speed = params.START_RETRACT_SPEED|default(120)|float * 60 %}
	{% set end_retract_speed = params.END_RETRACT_SPEED|default(20)|float * 60 %}
	
	DEBUG_ECHO PREFIX="_TIP_FORMING" MSG="cooling_moves: {cooling_moves}, cooling_move_length: {cooling_move_length}, start_cooling_speed: {start_cooling_speed}, end_cooling_speed: {end_cooling_speed}, dip: {dip}, dip_length: {dip_length}, dip_speed: {dip_speed}, dip_retract_speed: {dip_retract_speed}, retract_length: {retract_length}, start_retract_speed: {start_retract_speed}, end_retract_speed: {end_retract_speed}"
	
	M220 S100
	
	
	G92 E0
	{% set retract = retract_length + cooling_move_length / 2 - 15 %}
	G1 E-15 F{start_retract_speed}
	G1 E-{0.7 * retract} F{1.0 * end_retract_speed}
	G1 E-{0.2 * retract} F{0.5 * end_retract_speed}
	G1 E-{0.1 * retract} F{0.3 * end_retract_speed}
	
	
	G92 E0
	{% if cooling_moves > 0 %}
	{% set i = (end_cooling_speed - start_cooling_speed) / (2 * cooling_moves - 1) %}
	{% for m in range(cooling_moves) %}
	G1 E{cooling_move_length} F{(start_cooling_speed + i * m * 2)}
	G1 E-{cooling_move_length} F{(start_cooling_speed + i * (m * 2 + 1))}
	{% endfor %}
	{% endif %}
	
	
	G92 E0
	{% if dip %}
	G1 E{dip_length} F{dip_speed}
	G4 P100
	G1 E-{dip_length} F{dip_retract_speed}
	{% endif %}
	
	G92 E0
	M400

[delayed_gcode __ON_FILAMENT_SENSOR_BUTTON_PRESSED_STARTUP_GUARD]
initial_duration = 2.
gcode = 
	SET_GCODE_VARIABLE MACRO=_ON_FILAMENT_SENSOR_BUTTON_PRESSED VARIABLE=startup_complete VALUE=True

[gcode_macro _ON_FILAMENT_SENSOR_BUTTON_PRESSED]
variable_startup_complete = False
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set toolhead_sensor_button_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_sensor_button_only_when_sensor_enabled|default(false)|lower == 'true' %}
	
	
	{% if not startup_complete and sensor_enabled %}
	{action_emergency_stop("RatOS: The T%s filament sensor button was triggered immediately on printer startup. This is likely a false trigger. Please check your filament sensor wiring and configuration!" % (toolhead,))}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_SENSOR_BUTTON_PRESSED" MSG="TOOLHEAD: {toolhead}, SENSOR_ENABLED: {sensor_enabled}, TOOLHEAD_SENSOR_BUTTON_ONLY_WHEN_SENSOR_ENABLED: {toolhead_sensor_button_only_when_sensor_enabled}"
	
	{% if not printer.virtual_sdcard.is_active and (sensor_enabled or not toolhead_sensor_button_only_when_sensor_enabled) %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	{% set toolhead_detect_clog_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_detect_clog_only_when_sensor_enabled|default(true)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}, ENABLE_CLOG_DETECTION: {enable_clog_detection}, TOOLHEAD_DETECT_CLOG_ONLY_WHEN_SENSOR_ENABLED: {toolhead_detect_clog_only_when_sensor_enabled}, SENSOR_ENABLED: {sensor_enabled}"
	
	{% if enable_clog_detection and (sensor_enabled or not toolhead_detect_clog_only_when_sensor_enabled) %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_clog_detection %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_FILAMENT_END]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set clogged = true if params.CLOGGED|default(false)|lower == 'true' else false %}
	
	
	{% set unload_after_runout = printer["gcode_macro T%s" % toolhead].unload_after_runout|float %}
	
	
	{% if clogged %}
	_LED_FILAMENT_CLOG TOOLHEAD={toolhead}
	{% else %}
	_LED_FILAMENT_RUNOUT TOOLHEAD={toolhead}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_END" MSG="TOOLHEAD: {toolhead}"
	
	{% if printer.virtual_sdcard.is_active %}
	{% if not printer.pause_resume.is_paused %}
	PAUSE RUNOUT=True
	{% endif %}
	{% if not clogged and unload_after_runout %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	{% if not clogged and printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true'%}
	_JOIN_SPOOL TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M600]
description = Executes a color change by pausing the printer an unloading the filament.
gcode = 
	PAUSE
	UNLOAD_FILAMENT AUTOMATED=True
	RATOS_ECHO MSG="Please load new filament and resume"

[gcode_macro COLD_PULL]
description = Automated hotend cold pull.
gcode = 
	
	{% set extrusion_temp = params.EXTRUSION_TEMP|default(220)|int %}
	{% set cold_pull_temp = params.COLD_PULL_TEMP|default(80)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	
	{% if printer["dual_carriage"] is not defined %}
	{% set toolhead = 0 %}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead != 0 and toolhead != 1 %}
	{action_raise_error("Please select toolhead! 0 = left, 1 = right toolhead")}
	{% endif %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	RATOS_ECHO MSG="Starting cold pull on T{toolhead}..."
	{% else %}
	RATOS_ECHO MSG="Starting cold pull..."
	{% endif %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	SAVE_GCODE_STATE NAME=cold_pull_state
	
	
	{% if printer["dual_carriage"] is defined and "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	RATOS_ECHO MSG="Heating T{toolhead} to {extrusion_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={extrusion_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={extrusion_temp} MAXIMUM={extrusion_temp + 2}
	
	
	G4 P3000
	
	
	RATOS_ECHO MSG="extruding..."
	G92 E0
	G1 E30 F300
	G92 E0
	
	
	RATOS_ECHO MSG="Cooling T{toolhead} to {cold_pull_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={cold_pull_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={cold_pull_temp} MAXIMUM={cold_pull_temp + 2}
	
	
	G4 P10000
	
	
	RATOS_ECHO MSG="cold pull..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-40 VELOCITY=5 ACCEL=100
	
	
	RATOS_ECHO MSG="eject filament..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-200 VELOCITY=20 ACCEL=500
	
	
	RATOS_ECHO MSG="cooling down extruder..."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	RESTORE_GCODE_STATE NAME=cold_pull_state
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	
	CONSOLE_ECHO TITLE="Cold pull complete" MSG="Please remove the filament from the PTFE tube and cut the end off. Do NOT try to load it again." TYPE="warning"

[gcode_macro _USER_START_PRINT_BEFORE_HOMING]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_BED]
gcode = 

[gcode_macro _USER_START_PRINT_BED_MESH]
gcode = 

[gcode_macro _USER_START_PRINT_PARK]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 

[gcode_macro _USER_START_PRINT_HEAT_CHAMBER]
description = Uses the extruder sensor to wait for chamber temp. Override the _START_PRINT_HEAT_CHAMBER macro to implement heated chamber handling.
gcode = 
	
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}

[gcode_macro _USER_END_PRINT_BEFORE_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_AFTER_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_PARK]
gcode = 

[gcode_macro _USER_END_PRINT_FINISHED]
description = User hook for when the print is finished after gcode state has been restored.
gcode = 

[gcode_macro _USER_START_PRINT]
gcode = 

[gcode_macro _USER_END_START_PRINT]
gcode = 

[gcode_macro _USER_START_FEATURE]
gcode = 

[gcode_macro _USER_END_FEATURE]
gcode = 

[gcode_macro _USER_BEFORE_IDLE_TIMEOUT]
gcode = 

[gcode_macro _USER_AFTER_IDLE_TIMEOUT]
gcode = 

[gcode_macro ECHO_T_VARS]
description = Echo Toolhead variables to the console.
gcode = 
	{% set t = params.T|default(0) %}
	RATOS_ECHO MSG="T{t} Variables"
	{% for var, value in printer["gcode_macro T%s" % t].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ECHO_RATOS_VARS]
description = Echo RatOS variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro RatOS"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ENSURE_CRITICAL_RATOS_INIT]
variable_completed = False
gcode = 
	{% if not completed %}
	CALCULATE_PRINTABLE_AREA
	SET_GCODE_VARIABLE MACRO=ENSURE_CRITICAL_RATOS_INIT VARIABLE=completed VALUE=True
	{% endif %}

[delayed_gcode RATOS_INIT]
initial_duration = 0.1
gcode = 
	{action_respond_info("Initializing RatOS...")}
	ENSURE_CRITICAL_RATOS_INIT
	_LED_STANDBY
	INITIAL_FRONTEND_UPDATE
	_CHAMBER_FILTER_SANITY_CHECK
	{% if printer.fastconfig.settings.beacon is defined %}
	
	_BED_MESH_SANITY_CHECK
	{% endif %}
	{% set svv = printer.save_variables.variables %}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=0 C={svv.nozzle_expansion_coefficient_t0|default(0.06)|float}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=1 C={svv.nozzle_expansion_coefficient_t1|default(0.06)|float}
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=idex_applied_offset

[delayed_gcode RATOS_LOGO]
initial_duration = 2
gcode = 
	
	
	
	
	
	ENSURE_CRITICAL_RATOS_INIT
	HELLO_RATOS
	_ALERT_NON_ZERO_Z_OFFSET

[gcode_macro _ALERT_NON_ZERO_Z_OFFSET]
gcode = 
	{% set force = params.FORCE|default(0)|int == 1 %}
	{% set user_offset = printer.named_offsets.user_probe_z_offset.z|float %}
	{% set gcode_offset = printer.gcode_move.homing_origin.z|float %}
	{% set combined_offset = user_offset + gcode_offset %}
	
	{% if force or user_offset != 0 or gcode_offset != 0 %}
	{% set title = "User-adjusted Z-offset of %.3f mm is active" % combined_offset %}
	{% set msg = "" %}
	{% set nl = "" %}
	{% if user_offset != 0 %}
	{% set msg = msg + "beacon true zero user Z-offset: %.3f mm (to clear, use Z_OFFSET_APPLY_PROBE CLEAR=1)" % user_offset %}
	{% set nl = "_N_" %}
	{% endif %}
	{% if gcode_offset != 0 %}
	{% set msg = msg + nl + "G-code Z-offset: %.3f mm" % gcode_offset %}
	{% endif %}
	CONSOLE_ECHO TITLE="{title}" TYPE="info" MSG="{msg}"
	{% endif %}

[gcode_macro _INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE]
gcode = 
	{% set variable = params.VARIABLE|string %}
	{% set svv = printer.save_variables.variables %}
	{% set nlu_msg = "no longer used, please remove" %}
	{% if svv[variable] is defined %}
	{% set v = svv[variable]|string|replace('"', '')|replace("'", "") %}
	{% if not nlu_msg in v %}
	SAVE_VARIABLE VARIABLE={variable} VALUE='"{nlu_msg} (was {v})"'
	{% endif %}
	CONSOLE_ECHO TITLE="Deprecated ratos-variables.cfg variable" TYPE="warning" MSG="The variable {variable} is no longer used, please remove it from your ratos-variables.cfg file."
	{% endif %}

[gcode_macro _NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK]
gcode = 
	
	
	
	
	
	
	
	{% set t = params.T|int %}
	{% set c = params.C|float %}
	{% set normal_low = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_low|default(0.05)|float %}
	{% set normal_high = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_high|default(0.10)|float %}
	
	{% if c < 0 %}
	
	{action_emergency_stop("Invalid nozzle_expansion_coefficient_t%s value in ratos-variables.cfg: %.3f. It must be non-negative." % (t, c))}
	{% endif %}
	{% if c >= normal_high %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite high. Please verify that this is correct."
	{% endif %}
	{% if c <= normal_low %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite low. Please verify that this is correct."
	{% endif %}

[gcode_macro INITIAL_FRONTEND_UPDATE]
gcode = 
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_error = printer["gcode_macro RatOS"].status_color_error|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_unknown}"'
	{% endif %}
	
	
	{% set t0_sensor = "undefined" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	{% set t0_sensor = "detected" %}
	{% else %}
	{% set t0_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t0_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	{% set t1_sensor = "undefined" %}
	{% if printer["dual_carriage"] is defined and printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	{% set t1_sensor = "detected" %}
	{% else %}
	{% set t1_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t1_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	{% if svv.t0_filament is defined and printer["gcode_macro T0"] is defined %}
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	{% if t0_sensor != "empty" %}
	{% set t0_filament_type = svv.t0_filament[0]|default('')|string %}
	{% set t0_filament_name = svv.t0_filament[1]|default('')|string %}
	{% set t0_filament_temp = svv.t0_filament[2]|default(0)|float %}
	{% if t0_filament_name != '' and t0_filament_type != '' and t0_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{t0_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{t0_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={t0_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}
	{% if svv.t1_filament is defined and printer["gcode_macro T1"] is defined %}
	{% if printer["gcode_macro T1"].filament_name is defined and printer["gcode_macro T1"].filament_type is defined and printer["gcode_macro T1"].filament_temp is defined %}
	{% if t1_sensor != "empty" %}
	{% set t1_filament_type = svv.t1_filament[0]|default('')|string %}
	{% set t1_filament_name = svv.t1_filament[1]|default('')|string %}
	{% set t1_filament_temp = svv.t1_filament[2]|default(0)|float %}
	{% if t1_filament_name != '' and t1_filament_type != '' and t1_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='"{t1_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='"{t1_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE={t1_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t1_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro CALCULATE_PRINTABLE_AREA]
variable_calculated = False
gcode = 
	{% if not calculated %}
	{% set bed_margin_x = printer["gcode_macro RatOS"].bed_margin_x %}
	{% set bed_margin_y = printer["gcode_macro RatOS"].bed_margin_y %}
	
	
	
	{% set tool = 0 if printer["gcode_macro T0"] is not defined or printer["gcode_macro T0"].active else 1 %}
	{% set max_x = printer.toolhead.axis_maximum.x if printer["dual_carriage"] is defined and tool == 0 else printer.toolhead.axis_maximum.x - bed_margin_x[1] %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	
	
	{% set max_x = printer.toolhead.axis_maximum.x %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="printer.toolhead.axis_maximum.x {printer.toolhead.axis_maximum.x}"
	
	{% set max_y = printer.toolhead.axis_maximum.y - bed_margin_y[1]%}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_x_max VALUE={max_x}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_y_max VALUE={max_y}
	SET_GCODE_VARIABLE MACRO=CALCULATE_PRINTABLE_AREA VARIABLE=calculated VALUE=True
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	RATOS_LOG PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	{% endif %}

[gcode_macro CACHE_TOOLHEAD_SETTINGS]
variable_cache = {"global": {"accel": 1000, "ratio": 0.5, "speed": 50, "scv": 5}}
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set dummy = cache.__setitem__(key, {"accel": printer.toolhead.max_accel, "ratio": printer.toolhead.minimum_cruise_ratio, "speed": printer.toolhead.max_velocity, "scv": printer.toolhead.square_corner_velocity}) %}
	SET_GCODE_VARIABLE MACRO=CACHE_TOOLHEAD_SETTINGS VARIABLE=cache VALUE="{cache | pprint | replace("\n", "") | replace("\"", "\\\"")}"
	DEBUG_ECHO PREFIX="CACHE_TOOLHEAD_SETTINGS" MSG="Toolhead settings cached for {key}. {printer.toolhead.max_accel} accel, {printer.toolhead.minimum_cruise_ratio} ratio, {printer.toolhead.max_velocity} velocity, {printer.toolhead.square_corner_velocity} scv."

[gcode_macro RESTORE_TOOLHEAD_SETTINGS]
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set values = printer["gcode_macro CACHE_TOOLHEAD_SETTINGS"].cache.__getitem__(key) %}
	{% if values is not defined or values == 'None' %}
	{ action_raise_error("RESTORE_TOOLHEAD_SETTINGS: Toolhead settings not cached for key '" ~ key ~ "'.") }
	{% endif %}
	SET_VELOCITY_LIMIT ACCEL={values.accel} MINIMUM_CRUISE_RATIO={values.ratio} VELOCITY={values.speed} SQUARE_CORNER_VELOCITY={values.scv}
	DEBUG_ECHO PREFIX="RESTORE_TOOLHEAD_SETTINGS" MSG="Toolhead settings restored. {values.accel} accel, {values.ratio} ratio, {values.speed} velocity, {values.scv} scv."

[gcode_macro SET_MACRO_TRAVEL_SETTINGS]
gcode = 
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float %}
	{% set accel = printer["gcode_macro RatOS"].macro_travel_accel %}
	SET_VELOCITY_LIMIT ACCEL={accel} MINIMUM_CRUISE_RATIO=0.5 VELOCITY={speed} SQUARE_CORNER_VELOCITY={5}
	DEBUG_ECHO PREFIX="SET_MACRO_TRAVEL_SETTINGS" MSG="Macro travel settings set. {accel} accel, {speed} velocity"

[gcode_macro SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% if printer["dual_carriage"] is not defined %}
	
	SET_KINEMATIC_POSITION X={printable_x_max / 2} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	{% else %}
	
	IDEX_SET_CENTER_KINEMATIC_POSITION
	{% endif %}

[gcode_macro IDEX_SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x - (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x + (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY

[gcode_macro VERIFY_HYBRID_INVERTED]
gcode = 
	
	{% set inverted = False %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy is defined and printer.fastconfig.settings.ratos_hybrid_corexy.inverted is defined %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy.inverted|lower == 'true' %}
	{% set inverted = True %}
	{% endif %}
	{% endif %}
	{% if inverted == False %}
	{ action_emergency_stop("ratos_hybrid_corexy NOT INVERTED! Inverted hybrid core-xy bugfix not detected.") }
	{% endif %}

[gcode_macro RATOS_ECHO]
gcode = 
	{% set prefix = "RatOS" %}
	{% set debug = params.DEBUG|default(0)|int %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " | " ~ params.PREFIX %}
	{% endif %}
	{% set prefix = prefix ~ ":" %}
	{% set msg = "" %}
	{% if params.MSG is defined %}
	{% set msg = params.MSG %}
	{% else %}
	{% set msg = "No msg parameter provided (this is a bug or unintended use)." %}
	{% endif %}
	{% if not debug %}
	
	M117 {prefix} {msg}
	{% endif %}
	RATOS_LOG PREFIX="{prefix}" MSG="{msg}"
	{% if not debug %}
	RESPOND PREFIX="{prefix}" MSG="{msg}"
	{% else %}
	CONSOLE_ECHO TITLE="{prefix}" TYPE="debug" MSG="{msg}"
	{% endif %}

[gcode_macro ENABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=True
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=prefix_filter VALUE="'{params.FILTER|default('')|lower}'"
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging enabled."

[gcode_macro DISABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=False
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging disabled."

[gcode_macro DEBUG_ECHO]
variable_enabled = False
variable_prefix_filter = ''
gcode = 
	{% set prefix = "DEBUG" %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " - " ~ params.PREFIX %}
	{% endif %}
	{% if enabled and (prefix_filter|lower == '' or prefix_filter|lower in params.PREFIX|lower) %}
	RATOS_ECHO PREFIX="{prefix}" MSG="{params.MSG}" DEBUG=1
	{% endif %}

[gcode_macro START_FEATURE]
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="Start {params.FEATURE} feature gcode"
	{% set scv = printer.toolhead.square_corner_velocity|int|default(5) %}
	{% set accel = printer.toolhead.max_accel|int|default(10000) %}
	{% set ratio = printer.toolhead.minimum_cruise_ratio|float|default(0.5) %}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="scv" VALUE={scv}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="accel" VALUE={accel}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="ratio" VALUE={ratio}
	_USER_START_FEATURE FEATURE="{params.FEATURE}"

[gcode_macro END_FEATURE]
variable_scv = 5
variable_accel = 10000
variable_ratio = 0.5
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="End {params.FEATURE} feature gcode"
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={scv} ACCEL={accel} MINIMUM_CRUISE_RATIO={ratio}
	_USER_END_FEATURE FEATURE="{params.FEATURE}" SCV={scv} ACCEL={accel} RATIO={ratio}

[gcode_macro _ON_LAYER_CHANGE]
variable_layer_number = 0
description = INTERNAL USE ONLY. Call it from the slicers after layer change custom gcode
gcode = 
	
	{% set layer = params.LAYER|int %}
	
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE={layer}
	SET_PRINT_STATS_INFO CURRENT_LAYER={layer}

[gcode_macro _LEARN_MORE_CALIBRATION]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/calibration" %}
	{% set link_text = "RatOS Calibration Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_CHAMBER_FILTER]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter Control" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_FILAMENT]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/filaments" %}
	{% set link_text = "RatOS Filament Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _CONSOLE_SAVE_CONFIG]
gcode = 
	M118 Click <a class="command text--blue">SAVE_CONFIG</a> to save the settings to your printer.cfg.

[gcode_macro _LOAD_RATOS_SKEW_PROFILE]
gcode = 
	{% set ratos_skew_profile = printer["gcode_macro RatOS"].skew_profile|default("") %}
	{% if ratos_skew_profile != "" %}
	{% if printer.fastconfig.config["skew_correction %s" % ratos_skew_profile] is defined %}
	SKEW_PROFILE LOAD={ratos_skew_profile}
	GET_CURRENT_SKEW
	{% else %}
	{% set line_1 = '"Could not find skew profile %s!_N_Clearing skew correction."' % ratos_skew_profile %}
	CONSOLE_ECHO TITLE="Missing skew profile!" TYPE="warning" MSG={line_1}
	SET_SKEW CLEAR=1
	{% endif %}
	{% endif %}

[gcode_macro M601]
gcode = 
	PAUSE

[gcode_macro _STOP_AND_RAISE_ERROR]
gcode = 
	M84
	_RAISE_ERROR MSG="{params.MSG}"

[gcode_macro _RESET_GCODE_VARIABLES]
description = Reset specified [gcode_macro ...] variables to their original values from configuration when Klipper started.
	- MACRO: Name of the GCODE macro containing the variables to reset.
	- VARIABLES: Comma-separated list of variable names to reset (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- QUIET: (optional) If true, suppresses console echo messages for each reset variable. Default is false.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set quiet = params.QUIET|default("false")|lower in ("true", "1", "yes") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	{% set settings = printer.fastconfig.settings[obj_name|lower] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro %s]" % macro) }
	{% endif %}
	
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if settings["variable_%s" % var] is not defined %}
	{ action_raise_error("Variable '%s' is not defined in settings for [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	
	{% for var in vars %}
	{% set var_value = obj[var] %}
	{% if var_value is defined %}
	{% set v = settings["variable_%s" % var] %}
	{% if v != var_value|string %}
	{% if var_value is string %}
	{% set v = '"\'' ~ v|replace('"', '\\"')|replace("'", "\\'") ~ '\'"' %}
	{% endif %}
	SET_GCODE_VARIABLE MACRO={macro} VARIABLE={var} VALUE={v}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Reset {macro} variable {var} to original value: {v} (was {obj[var]})"
	{% endif %}
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro _SHOW_GCODE_VARIABLES]
description = Show current values of specified [gcode_macro ...] variables.
	- MACRO: Name of the GCODE macro containing the variables to show.
	- VARIABLES: Comma-separated list of variable names to show (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- PAD: (optional) If defined, provide a single character to use for padding variable names to align values in a tabular format in the console output. Default is no padding.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set pad = params.PAD|default("") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	
	{% set ns = namespace() %}
	{% set ns.max_len = 0 %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% set ns.max_len = (ns.max_len, var|length)|max %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if pad %}
	{% set padding = pad * (ns.max_len - var|length) %}
	CONSOLE_ECHO MSG="{var}{padding} {obj[var]}"
	{% else %}
	CONSOLE_ECHO MSG="{var}: {obj[var]}"
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro PAUSE]
description = Pauses the print
rename_existing = PAUSE_BASE
variable_extrude = 1.5
variable_retract = 1.5
variable_fan_speed = 0
variable_idex_mode = ""
variable_idex_toolhead = 0
variable_idex_toolhead_x = 0.0
variable_idex_toolhead_y = 0.0
variable_idex_toolhead_z = 0.0
gcode = 
	RATOS_ECHO MSG="Pausing print..."
	
	
	{% set runout_detected = true if params.RUNOUT|default(false)|lower == 'true' else false %}
	
	
	_LED_PAUSE
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	SAVE_GCODE_STATE NAME=PAUSE_state
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_mode VALUE='"{idex_mode}"'
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={idex_toolhead}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_x VALUE={printer.gcode_move.gcode_position.x|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_y VALUE={printer.gcode_move.gcode_position.y|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_z VALUE={printer.gcode_move.gcode_position.z|float}
	DEBUG_ECHO PREFIX="PAUSE" MSG="idex_mode: {idex_mode}, idex_toolhead: {idex_toolhead}, idex_toolhead_x: {idex_toolhead_x}, idex_toolhead_y: {idex_toolhead_y}, idex_toolhead_z: {idex_toolhead_z}"
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="pause"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if current_z < (max_z - 20.0) %}
	{% set z_safe = 20.0 %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	PAUSE_BASE
	
	
	{% if printer["dual_carriage"] is not defined %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan"].speed|float}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	{% if idex_toolhead == 0 %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t1"].speed|float}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106 S0
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set R = printer["gcode_macro PAUSE"].retract|float %}
	{% if can_extrude %}
	G91
	G1 E-{R} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	{% set pause_print_park_x = printer["gcode_macro RatOS"].pause_print_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].pause_print_park_in %}
	{% if runout_detected %}
	{% set pause_print_park_x = printer["gcode_macro RatOS"].runout_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].runout_park_in %}
	{% endif %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	DEBUG_ECHO PREFIX="PAUSE" MSG="z_speed: {z_speed}, pause_print_park_x: {pause_print_park_x}, pause_print_park_in: {pause_print_park_in}, default_toolhead: {default_toolhead}"
	{% if "xyz" in printer.toolhead.homed_axes %}
	G91
	G1 Z{z_safe} F{z_speed}
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% else %}
	
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	_IDEX_SINGLE X={parking_position}
	{% else %}
	PARK_TOOLHEAD
	{% endif %}
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="pause"
	
	RATOS_ECHO MSG="Print paused"

[gcode_macro RESUME]
description = Resumes the print if the printer is paused.
rename_existing = RESUME_BASE
gcode = 
	
	
	RATOS_ECHO MSG="Resuming print..."
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	
	{% set target_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set target_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if target_idex_mode != '' %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set fan_speed = printer["gcode_macro PAUSE"].fan_speed|float %}
	{% if printer["dual_carriage"] is not defined %}
	M106 S{(fan_speed * 255)}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% else %}
	{% if params.TOOLHEAD is defined %}
	
	{% if params.TOOLHEAD == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% else %}
	{% if printer["gcode_macro PAUSE"].idex_toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	{% if params.TOOLHEAD is defined %}
	_SELECT_TOOL T={params.TOOLHEAD} X=-1 Y=-1 TOOLSHIFT=false
	{% else %}
	_SELECT_TOOL T={printer["gcode_macro PAUSE"].idex_toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	{% endif %}
	
	{% set x = printer["gcode_macro PAUSE"].idex_toolhead_x|float %}
	{% set y = printer["gcode_macro PAUSE"].idex_toolhead_y|float %}
	{% set z = printer["gcode_macro PAUSE"].idex_toolhead_z|float %}
	G1 X{x} Y{y} Z{z} F{speed}
	{% if params.TOOLHEAD is defined %}
	
	SAVE_GCODE_STATE NAME=PAUSE_STATE
	{% endif %}
	{% endif %}
	
	
	{% if params.TOOLHEAD is not defined %}
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% if can_extrude %}
	G91
	G1 E{E} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1 MOVE_SPEED={speed}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	RESUME_BASE
	
	
	_LED_PRINTING
	
	RATOS_ECHO MSG="Print resumed"

[gcode_macro CANCEL_PRINT]
description = Cancels the print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	RATOS_ECHO MSG="Cancelling print..."
	END_PRINT
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	
	CANCEL_PRINT_BASE
	RATOS_ECHO MSG="Print cancelled"

[gcode_macro START_PRINT]
description = Start print procedure, use this in your Slicer.
variable_post_processor_version = 2
variable_is_printing_gcode = False
variable_both_toolheads = True
variable_object_xoffset = 0
variable_first_x = -1
variable_first_y = -1
variable_total_toolshifts = 0
variable_initial_tool = 0
variable_extruder_first_layer_temp = ""
variable_extruder_other_layer_temp = ""
gcode = 
	
	{% if params.EXTRUDER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_TEMP parameter not found.")}
	{% endif %}
	{% if params.EXTRUDER_OTHER_LAYER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_OTHER_LAYER_TEMP parameter not found.")}
	{% endif %}
	{% if params.BED_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. BED_TEMP parameter not found.")}
	{% endif %}
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' and printer["gcode_macro RatOS"].danger_force_allow_auto_center_subject|default(false)|lower != 'true'%}
	
	
	
	
	
	{ action_raise_error("The experimental auto_center_subject feature is not supported in this version of RatOS. Please disable it in the RatOS macro settings.") }
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes and printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% if printer["gcode_macro _VAOC"].is_started|default(true)|lower == 'true' %}
	_VAOC_END
	{% endif %}
	{% endif %}
	
	
	_LED_START_PRINTING
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_USER_START_PRINT { rawparams }
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_probe_stowable = printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% endif %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	{% set X0 = params.X0|default(-1)|float %}
	{% set X1 = params.X1|default(-1)|float %}
	{% set Y0 = params.Y0|default(-1)|float %}
	{% set Y1 = params.Y1|default(-1)|float %}
	{% if first_x == -1 or first_y == -1 %}
	{% set first_x = params.FIRST_X|default(-1)|float %}
	{% set first_y = params.FIRST_Y|default(-1)|float %}
	{% endif %}
	{% set total_toolshifts = params.TOTAL_TOOLSHIFTS|default(0)|int %}
	{% set initial_tool = params.INITIAL_TOOL|default(default_toolhead)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	
	
	
	
	
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(printer.heater_bed.target, true)|float %}
	
	
	{% set total_layer_count = params.TOTAL_LAYER_COUNT|default(0)|int %}
	{% set extruder_first_layer_temp = (params.EXTRUDER_TEMP|default("")).split(",") %}
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL BEACON_CONTACT_START_PRINT_TRUE_ZERO={beacon_contact_start_print_true_zero} BEACON_CONTACT_CALIBRATE_MODEL_ON_TRUE_ZERO={beacon_contact_calibrate_model_on_true_zero}
	{% endif %}
	
	_START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH BED_TEMP={bed_temp}
	
	
	RATOS_ECHO MSG="First print coordinates X:{first_x} Y:{first_y}"
	
	
	{% if params.TOTAL_LAYER_COUNT is not defined %}
	{% set link_url = "https://os.ratrig.com/docs/slicers" %}
	{% set link_text = "RatOS Slicer Configuration" %}
	{% set line_1 = '"Your slicer gcode settings are not up to date._N_Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="Incomplete Slicer Configuration detected" TYPE="warning" MSG={line_1}
	{% endif %}
	
	
	SET_PRINT_STATS_INFO CURRENT_LAYER=1
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE=1
	{% if total_layer_count > 0 %}
	SET_PRINT_STATS_INFO TOTAL_LAYER={total_layer_count}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads %}
	{% set initial_tool = 0 if initial_tool == 1 else 1 %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	{% endif %}
	
	
	{% set both_toolheads = true %}
	{% if total_toolshifts == 0 %}
	{% set both_toolheads = false %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	{% endif %}
	{% if both_toolheads and (idex_mode == "copy" or idex_mode == "mirror") %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Gcode tool changes found. Copy and mirror mode do not support toolchanges.")}
	{% endif %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set both_toolheads = true %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=initial_tool VALUE={initial_tool}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_x VALUE={first_x}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_y VALUE={first_y}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=total_toolshifts VALUE={total_toolshifts}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=both_toolheads VALUE={both_toolheads}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_first_layer_temp VALUE="'{params.EXTRUDER_TEMP}'"
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_other_layer_temp VALUE="'{params.EXTRUDER_OTHER_LAYER_TEMP}'"
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE=0
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set svv = printer.save_variables.variables %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set stepper_x_position_min = printer.fastconfig.settings.stepper_x.position_min|float %}
	{% set stepper_x_position_endstop = printer.fastconfig.settings.stepper_x.position_endstop|float %}
	{% set dual_carriage_position_max = printer.fastconfig.settings.dual_carriage.position_max|float %}
	{% set dual_carriage_position_endstop = printer.fastconfig.settings.dual_carriage.position_endstop|float %}
	{% set x_parking_space = parking_position_t0 - (stepper_x_position_endstop , stepper_x_position_min)|max %}
	{% set dc_parking_space = (dual_carriage_position_endstop , dual_carriage_position_max)|min - parking_position_t1 %}
	{% if svv.idex_xoffset|abs >= (x_parking_space - 0.5) or svv.idex_xoffset|abs >= (dc_parking_space - 0.5) %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Toolhead x-offset is too high for the available parking space. Calibrate your X and DC endstop positions and make sure you stay below 1mm." % (copy_mode_max_width)) }
	{% endif %}
	{% endif %}
	
	
	{% if (idex_mode == "copy" or idex_mode == "mirror") and printer.fastconfig.settings.ratos.enable_gcode_transform %}
	
	{% if params.MIN_X is not defined or params.MAX_X is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Something went wrong! Missing important post processor start print parameter!") }
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE=0
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	
	{% set boundary_box_min_x = params.MIN_X|default(0)|float %}
	{% set boundary_box_max_x = params.MAX_X|default(printable_x_max)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if default_toolhead == 0 %}
	
	{% set boundary_box_max_x = boundary_box_max_x + svv.idex_xoffset %}
	{% else %}
	
	{% set boundary_box_min_x = boundary_box_min_x - svv.idex_xoffset %}
	{% endif %}
	
	{% set center_x = printable_x_max / 2.0 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set object_width = boundary_box_max_x - boundary_box_min_x %}
	{% set copy_mode_max_width = center_x %}
	{% set mirror_mode_max_width = center_x - safe_distance / 2.0 %}
	
	DEBUG_ECHO PREFIX="START_PRINT" MSG="OBJECT_WIDTH: {object_width} BOUNDARY_BOX_MIN_X: {boundary_box_min_x} BOUNDARY_BOX_MAX_X: {boundary_box_max_x} CENTER_X: {center_x} SAFE_DISTANCE: {safe_distance}"
	
	
	{% if idex_mode == "copy" and object_width > copy_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for copy mode! Max supported width is %s mm" % (copy_mode_max_width)) }
	{% endif %}
	{% if idex_mode == "mirror" and object_width > mirror_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for mirror mode! Max supported width is %s mm" % (mirror_mode_max_width)) }
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = (printable_x_max - boundary_box_max_x - boundary_box_min_x) / 2 %}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE={object_xoffset}
	{% endif %}
	
	{% endif %}
	
	
	{% set has_initial_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_toolhead_filament_sensor %}
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% set has_initial_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_bowden_filament_sensor %}
	
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% if printer["dual_carriage"] is defined and both_toolheads %}
	
	{% set has_secondary_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set has_secondary_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_CHAMBER_FILTER_ON AT="before_print_start"
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true' %}
	{% if both_toolheads %}
	RATOS_ECHO MSG="Spool join is not possible if both toolheads are in use!"
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	{% endif %}
	
	
	CLEAR_PAUSE
	{% if printer["gcode_macro RatOS"].force_absolute_position|lower == 'true' %}
	G90
	{% endif %}
	SAVE_GCODE_STATE NAME=start_print_state
	
	
	G21
	
	G90
	
	M82
	_USER_START_PRINT_BEFORE_HOMING { rawparams }
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_BEGIN_BATCH
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_Z_HOP
	
	
	{% if idex_mode != '' and not (printer.fastconfig.settings.beacon is defined and (beacon_contact_start_print_true_zero or beacon_adaptive_heat_soak)) %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	{% if chamber_temp > 0 %}
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED={printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float}
	{% endif %}
	{% endif %}
	_CHAMBER_HEATER_ON START_CHAMBER_TEMP={start_chamber_temp} CHAMBER_TEMP={chamber_temp}
	_USER_START_PRINT_HEAT_CHAMBER { rawparams } CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_START_PRINT_BEFORE_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	RATOS_ECHO MSG="Heating bed..."
	
	M190 S{bed_temp}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_adaptive_heat_soak %}
	_MOVE_TO_SAFE_Z_HOME
	
	G1 Z2.5 F{z_speed}
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK LAYER_QUALITY={beacon_adaptive_heat_soak_layer_quality} MAXIMUM_FIRST_LAYER_DURATION={beacon_adaptive_heat_soak_maximum_first_layer_duration} MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={beacon_adaptive_heat_soak_max_wait}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_BED { rawparams }
	
	
	_START_PRINT_AFTER_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	_USER_START_PRINT_BED_MESH { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_BED_MESH X0={X0} X1={X1} Y0={Y0} Y1={Y1} T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_END_BATCH
	{% endif %}
	
	
	{% if idex_mode == '' %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[initial_tool]|float}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[0]|float}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={extruder_first_layer_temp[1]|float}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_PARK { rawparams }
	
	
	_START_PRINT_PARK
	
	
	RATOS_ECHO MSG="Heating Extruder..."
	{% if idex_mode == '' %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[initial_tool]|float}  MAXIMUM={extruder_first_layer_temp[initial_tool]|float + 5}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[0]|float}  MAXIMUM={extruder_first_layer_temp[0]|float + 5}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder1" MINIMUM={extruder_first_layer_temp[1]|float}  MAXIMUM={extruder_first_layer_temp[1]|float + 5}
	{% endif %}
	{% endif %}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	{% if idex_mode == '' %}
	_LED_PRINTING
	{% else %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	_LED_PRINTING
	{% else %}
	{% if both_toolheads %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	{% if toolchange_standby_temp > -1 %}
	_LED_TOOLHEAD_STANDBY TOOLHEAD={0 if initial_tool == 1 else 1}
	{% else %}
	_LED_PRINTING TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% else %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_EXTRUDER { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_AFTER_HEATING_EXTRUDER X0={X0} X1={X1} Y0={Y0} Y1={Y1} INITIAL_TOOLHEAD={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if idex_mode != '' %}
	{% if not both_toolheads %}
	{% if initial_tool != default_toolhead %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if idex_mode != '' %}
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=standby VALUE=False
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=standby VALUE=False
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if initial_tool == 1 else 'extruder1'} TARGET={toolchange_standby_temp}
	SET_GCODE_VARIABLE MACRO=T{0 if initial_tool == 1 else 1} VARIABLE=standby VALUE=True
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=start_print_state
	
	{% if printer["dual_carriage"] is defined %}
	_SET_IDEX_MODE_OFFSET
	{% endif %}
	
	
	{% if idex_mode != '' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% if idex_mode == "copy" and idex_mode != act_idex_mode %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == "mirror" and idex_mode != act_idex_mode %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={object_xoffset} MOVE=0
	{% endif %}
	{% else %}
	_SELECT_TOOL T={initial_tool} TOOLSHIFT=false
	_SET_TOOLHEAD_OFFSET
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	_SET_EXTRUSION_MODE
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={printer["print_stats"].print_duration}
	{% endif %}
	
	
	_USER_END_START_PRINT { rawparams }
	
	G92 E0
	
	
	_CHAMBER_FILTER_ON AT="after_print_start"
	
	_ALERT_NON_ZERO_Z_OFFSET
	
	RATOS_ECHO MSG="Printing..."

[gcode_macro _START_PRINT_BEFORE_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set is_stowable_probe = true if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' else false %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Pre-heating extruder..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={min_temp}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET={min_temp}
	{% endif %}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	{% endif %}
	{% endif %}
	
	
	{% if not is_stowable_probe %}
	{% if printer["dual_carriage"] is defined and act_t != default_toolhead %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	{% endif %}
	RATOS_ECHO MSG="Heat soaking z probe..."
	_MOVE_TO_SAFE_Z_HOME
	
	G0 Z2 F{z_speed}
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Waiting for extruder to be preheated..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	{% if default_toolhead == 0 %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_Z_HOP
	{% endif %}
	
	
	{% if auto_z_offset_calibration %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	PARK_TOOLHEAD
	_CLEANING_MOVE TOOLHEAD={default_toolhead} AUTOMATED=True
	_SELECT_TOOL T={0 if default_toolhead == 1 else 1} X={parking_position_t0 if default_toolhead == 1 else parking_position_t1} Y=0 TOOLSHIFT=false
	_CLEANING_MOVE TOOLHEAD={0 if default_toolhead == 1 else 1} AUTOMATED=True
	_VAOC_CALIBRATE_Z_OFFSET AUTO_Z_OFFSET=True
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=false
	{% endif %}
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	{% if needs_rehoming %}
	G28 Z
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	_START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE
	{% endif %}
	{% endif %}
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	PROBE PROBE_METHOD=contact SAMPLES=1

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	{% set fuzzy_radius = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_radius|default(0)|float if beacon_contact_start_print_true_zero_fuzzy_position else 0 %}
	
	{% set contact_true_zero_temp_has_been_set = False %}
	
	
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	
	
	
	{% if printer.beacon.last_probe_result|lower == "ok" %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	RATOS_ECHO MSG="Auto calibration nozzle wipe with probe result {last_z_offset}..."
	G0 Z{(0.2 + last_z_offset)} F{z_speed}
	G0 X70 F300
	{% else %}
	RATOS_ECHO MSG="Skipping auto calibration nozzle wipe because probing failed!"
	{% endif %}
	{% elif beacon_contact_wipe_before_true_zero_method == "probe_clean" %}
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	
	{% set contact_true_zero_temp_has_been_set = True %}
	
	
	
	
	
	
	
	
	BEACON_PROBE_CLEAN X=50 Y=10
	{% else %}
	CONSOLE_ECHO TYPE="error" TITLE="Unknown wipe method" MSG="Unknown wipe method '{beacon_contact_wipe_before_true_zero_method}' configured, skipping wipe before beacon true zero."
	{% endif %}
	{% endif %}
	
	
	G0 Z5 F{z_speed}
	_MOVE_TO_SAFE_Z_HOME FUZZY_RADIUS={fuzzy_radius}
	
	
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION
	
	{% if not contact_true_zero_temp_has_been_set %}
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon contact auto calibration..."
	
	{% if beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	
	G0 Z5 F{z_speed}

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION]
gcode = 
	{% set pos = printer.ratos.last_move_to_safe_z_home_position %}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE={pos[0]}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE={pos[1]}

[gcode_macro _START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set first_x = printer["gcode_macro START_PRINT"].first_x|default(-1)|float %}
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2.0 %}
	{% set center_y = printable_y_max / 2.0 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% if printer["dual_carriage"] is defined %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% endif %}
	
	
	{% set X0 = params.X0|default(-1)|int %}
	{% set X1 = params.X1|default(-1)|int %}
	{% set Y0 = params.Y0|default(-1)|int %}
	{% set Y1 = params.Y1|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	
	{% if idex_mode == '' %}
	
	_PRIME
	{% else %}
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	RATOS_ECHO PREFIX="IDEX" MSG="using combined prime offset for IDEX {idex_mode} mode"
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	{% if both_toolheads %}
	{% if initial_toolhead == 0 %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T{initial_toolhead}"
	_SELECT_TOOL T={initial_toolhead} TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	SET_MACRO_TRAVEL_SETTINGS
	
	{% if (X0 > -1 and Y1 > -1) or (first_x > 0 and first_y > 0) %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	{% endif %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	{% set first_z = 1 %}
	{% else %}
	{% set first_z = 3 %}
	{% endif %}
	
	
	{% if idex_mode == "mirror" %}
	{% if first_y >= 0 %}
	G0 Y{first_y} F{speed}
	{% else %}
	G0 Y{Y1} F{speed}
	{% endif %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={initial_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={initial_toolhead} E={printer["gcode_macro RatOS"].toolchange_first_purge|default(50)|float}
	_CLEANING_MOVE TOOLHEAD={initial_toolhead} AUTOMATED=True
	{% endif %}
	{% if first_x >= 0 and first_y >= 0 %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% else %}
	{% set first_x = X0 %}
	{% set first_y = Y0 %}
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'min' %}
	{% set first_x = X0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'max' %}
	{% set first_x = X1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|float <= center_x %}
	{% set first_x = X0 %}
	{% else %}
	{% set first_x = X1 %}
	{% endif %}
	{% endif %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'min' %}
	{% set first_y = Y0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'max' %}
	{% set first_y = Y1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|float <= center_y %}
	{% set first_y = Y0 %}
	{% else %}
	{% set first_y = Y1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	
	
	_LOAD_RATOS_SKEW_PROFILE

[gcode_macro _PRIME]
gcode = 
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	PRIME_BLOB INITIAL_TOOLHEAD={params.INITIAL_TOOLHEAD} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={params.IDEX_MODE} Y1={params.Y1}
	{% else %}
	
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif params.IDEX_MODE == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro END_PRINT]
description = End print procedure, use this in your Slicer.
gcode = 
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SAVE_GCODE_STATE NAME=end_print_state
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = printer["gcode_macro START_PRINT"].object_xoffset|default(0)|float %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(0-object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={(0-object_xoffset)}
	{% endif %}
	{% endif %}
	
	
	_USER_END_PRINT_BEFORE_HEATERS_OFF { rawparams }
	_END_PRINT_BEFORE_HEATERS_OFF
	TURN_OFF_HEATERS
	_USER_END_PRINT_AFTER_HEATERS_OFF { rawparams }
	_END_PRINT_AFTER_HEATERS_OFF
	_USER_END_PRINT_PARK { rawparams }
	_END_PRINT_PARK
	
	
	{% if printer["gcode_macro RatOS"].skew_profile is defined %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined and printer["gcode_macro RatOS"].end_print_motors_off|lower != 'false' %}
	
	M84
	{% endif %}
	
	
	M107
	
	
	BED_MESH_CLEAR
	RATOS_ECHO MSG="Done :)"
	
	
	RESTORE_GCODE_STATE NAME=end_print_state
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	M84
	{% endif %}
	
	
	RESET_NAMED_OFFSET EVENT="end_print"
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_CHAMBER_FILTER_ON AT="print_end"
	_CHAMBER_FILTER_OFF
	
	
	_CHAMBER_HEATER_OFF
	
	_USER_END_PRINT_FINISHED { rawparams }

[gcode_macro _END_PRINT_BEFORE_HEATERS_OFF]
gcode = 
	RATOS_ECHO MSG="Cleaning up..."

[gcode_macro _END_PRINT_AFTER_HEATERS_OFF]
gcode = 
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% set z_hop = printer["gcode_macro RatOS"].end_print_park_z_hop|float %}
	{% set r = printer["gcode_macro RatOS"].end_print_retract_filament|default(4)|float %}
	{% if current_z < (max_z - z_hop) %}
	{% set z_safe = z_hop %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G91
	
	{% if can_extrude %}
	G1 E-2 F3600
	{% endif %}
	
	G0 Z{z_safe} F3600
	
	{% if can_extrude %}
	G1 E-{(r-2)} F3600
	{% endif %}
	
	G90

[gcode_macro _SET_EXTRUSION_MODE]
gcode = 
	
	{% if printer["gcode_macro RatOS"].relative_extrusion|lower == 'true' %}
	M83
	{% else %}
	M82
	{% endif %}

[gcode_macro GENERATE_SHAPER_GRAPHS]
description = Genarates input shaper resonances graphs for analysis. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	{% set hz_per_sec = params.HZ_PER_SEC|default(1)|float %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set copy_mode_offset = printable_x_max / 4.0 %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	_IDEX_SINGLE
	{% endif %}
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	
	
	{% if idex_mode != 'copy' and idex_mode != 'mirror' %}
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	{% endif %}
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Shaper graph"

[gcode_shell_command generate_shaper_graph_x]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-x.sh
timeout = 60.
verbose = True

[gcode_shell_command generate_shaper_graph_y]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-y.sh
timeout = 60.
verbose = True

[gcode_macro MEASURE_COREXY_BELT_TENSION]
description = Generates resonance graph used to ensure belts are equally tensioned. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	_IDEX_SINGLE
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if measure_t1 == false or measure_t0 == false %}
	{action_raise_error("Axis specified. Not supported for belt tension on Y.")}
	{% else %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	G4 P5000
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	PARK_TOOLHEAD
	{% endif %}
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	G1 X{parking_position_t1} F{speed}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	
	
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Belt Tension Graph"

[gcode_shell_command generate_belt_tension_graph]
command = /home/pi/printer_data/config/RatOS/scripts/generate-belt-tension-graph.sh
timeout = 90.
verbose = True

[idle_timeout]
gcode = 
	{% if printer.webhooks.state|lower == 'ready' %}
	{% if printer.pause_resume.is_paused|lower == 'false' %}
	_USER_BEFORE_IDLE_TIMEOUT
	RATOS_ECHO PREFIX="IDLE" MSG="2 hours since last activity. Powering off heaters and motors.."
	TURN_OFF_HEATERS
	M84
	_USER_AFTER_IDLE_TIMEOUT
	{% endif %}
	{% endif %}
timeout = 7200

[temperature_sensor raspberry_pi]
sensor_type = temperature_host

[skew_correction]

[named_offsets]

[input_shaper]

[virtual_sdcard]
path = ~/printer_data/gcodes

[display_status]

[pause_resume]

[force_move]
enable_force_move = True

[respond]

[resonance_generator]

[ratos]
allow_unknown_gcode_generator = True
enable_gcode_transform = True

[exclude_object]

[bed_mesh]
split_delta_z = 0.001
horizontal_move_z = 2
mesh_min = 20,20
mesh_max = 480,480
probe_count = 40,40
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = .2
speed = 600
log_points = False

[fastconfig]

[heater_bed]
heater_pin = heater_bed_heating_pin
sensor_pin = heater_bed_sensor_pin
sensor_type = Generic 3950
min_temp = 0
max_temp = 140
pwm_cycle_time = 0.103
control = pid
pid_kp = 61.987
pid_ki = 1.781
pid_kd = 539.289

[printer]
kinematics = ratos_hybrid_corexy
max_velocity = 800
max_accel = 10000
minimum_cruise_ratio = 0.5
max_z_velocity = 50
max_z_accel = 600
square_corner_velocity = 5

[ratos_hybrid_corexy]
inverted = true

[dual_carriage]
axis = x
safe_distance = 55
position_max = 559.6
position_endstop = 559.6
position_min = 0
step_pin = PF9
dir_pin = dual_carriage_dir_pin
enable_pin = !PG2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t1:PA2

[gcode_macro _SET_IDEX_MODE_OFFSET]
description = "Internal use only. Sets the 'idex_mode' named offset that the active idex mode requires."
gcode = 
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_SET_IDEX_MODE_OFFSET" MSG="idex_mode: {idex_mode}, center_x: {center_x}"
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	SET_NAMED_OFFSET NAME=idex_mode X={(-center_x / 2)}
	{% else %}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% else %}
	{action_raise_error("_SET_IDEX_MODE_OFFSET: Printer not homed")}
	{% endif %}

[gcode_macro IDEX_SINGLE]
gcode = 
	_IDEX_REMAP_TOOLHEADS ENABLE=False
	_IDEX_SINGLE

[gcode_macro _IDEX_SINGLE]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_single"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set init = params.INIT|default(0)|int %}
	{% set new_x = params.X|default(-1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_default_t = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="init: {init}, new_x: {new_x}, idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, act_t: {act_t}"
	
	{% if idex_mode == "copy" or idex_mode == "mirror" or init == 1 %}
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="reset idex_mode offset"
	G1 X{center_x} F{(speed)}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="activate default carriage"
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolheads"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	G90
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position."
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1}
	G1 X{parking_position_default_t} F{speed}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move default toolhead to its new position."
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% if new_x == -1 %}
	{% set new_x = center_x %}
	{% endif %}
	G1 X{new_x} F{speed}
	
	M400
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="X Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set extruder motion queue."
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if default_toolhead==0 else default_toolhead}
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolhead offset."
	_SET_TOOLHEAD_OFFSET
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set input shaper."
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[default_toolhead]|float)} SHAPER_FREQ_Y={(shaper_y_freq[default_toolhead]|float)} SHAPER_TYPE_X={(shaper_x_type[default_toolhead]|lower)} SHAPER_TYPE_Y={(shaper_y_type[default_toolhead]|lower)}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="update Frontend."
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if default_toolhead==0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if default_toolhead==1 else False}
	{% else %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_single"

[gcode_macro IDEX_COPY]
gcode = 
	_IDEX_COPY

[gcode_macro _IDEX_COPY]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_copy"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set y = params.Y|default(-1)|int %}
	{% set dance = params.DANCE|default(1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_COPY" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}, y: {y}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "copy" %}
	{% if idex_mode == "mirror" %}
	{% if y>=0 %}
	G1 X{center_x} Y{y} F{(speed)}
	{% else %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	
	
	{% if idex_mode != "mirror" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance == 1 %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[2]|float)} SHAPER_FREQ_Y={(shaper_y_freq[2]|float)} SHAPER_TYPE_X={(shaper_x_type[2]|lower)} SHAPER_TYPE_Y={(shaper_y_type[2]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_copy"

[gcode_macro IDEX_MIRROR]
gcode = 
	_IDEX_MIRROR

[gcode_macro _IDEX_MIRROR]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_mirror"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set dance = params.DANCE|default(1)|int %}
	{% set priming = params.PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_MIRROR" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "mirror" %}
	
	{% if idex_mode == "copy" %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS MIRROR_PRIMING={params.PRIMING}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=MIRROR
	
	
	{% if idex_mode != "copy" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance and not priming %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[3]|float)} SHAPER_FREQ_Y={(shaper_y_freq[3]|float)} SHAPER_TYPE_X={(shaper_x_type[3]|lower)} SHAPER_TYPE_Y={(shaper_y_type[3]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_mirror"

[gcode_macro _IDEX_SET_TOOLHEADS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set mirror_priming = params.MIRROR_PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position_inactive_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_IDEX_SET_TOOLHEADS" MSG="idex_mode: {idex_mode}, act_t: {act_t}, center_x: {center_x}, mirror_priming: {mirror_priming}"
	
	
	{% if act_t != default_toolhead %}
	_SET_TOOLHEAD_OFFSET FORCE_TOOLHEAD={default_toolhead} MOVE=1
	{% endif %}
	
	{% if mirror_priming %}
	
	
	
	{% if parking_position_t0|abs < parking_position_t1 - printable_x_max %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{printable_x_max + parking_position_t0|abs} F{(speed)}
	{% else %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{0 - (parking_position_t1 - printable_x_max)} F{(speed)}
	{% endif %}
	
	{% else %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1} MODE=PRIMARY
	G1 X{parking_position_inactive_t} F{(speed)}
	
	
	{% if act_t==1 %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{center_x / 2} F{(speed)}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"

[gcode_macro IDEX_PARK]
gcode = 
	
	PARK_TOOLHEAD

[gcode_macro PARK_TOOLHEAD]
gcode = 
	
	{% set idex_mode = 'none' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="PARK_TOOLHEAD" MSG="Parking T{act_t}.."
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set parking_position_inact_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set printable_y_min = printer["gcode_macro RatOS"].printable_y_min|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" and 'xy' in printer.toolhead.homed_axes %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% elif printer.toolhead.position.y|float < printable_y_min %}
	G1 Y{printable_y_min} F{speed}
	{% endif %}
	
	SAVE_GCODE_STATE NAME=_PARK_TOOLHEAD
	G90
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0.5
	
	
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_inact_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	
	SET_VELOCITY_LIMIT ACCEL={printer.toolhead.max_accel} MINIMUM_CRUISE_RATIO=0.5
	M400
	RESTORE_GCODE_STATE NAME=_PARK_TOOLHEAD
	
	{% endif %}

[gcode_macro JOIN_SPOOLS]
gcode = 
	
	{% set spools = params.SPOOLS|default("") %}
	
	{% if spools == "" %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% else %}
	{% if spools != "0,1" and spools != "1,0" %}
	RATOS_ECHO MSG="Wrong spool configuration!"
	RATOS_ECHO MSG="Join Spools = JOIN_SPOOLS SPOOLS=0,1"
	RATOS_ECHO MSG="Deactivate = JOIN_SPOOLS SPOOLS="
	{% else %}
	{% if spools == "0,1" or spools == "1,0" %}
	_IDEX_JOIN_SPOOLS ENABLE=true
	{% else %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_JOIN_SPOOLS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if enable %}
	{% set has_t0_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t1_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t0_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined else false %}
	{% set has_t1_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined else false %}
	{% if (has_t0_toolhead_filament_sensor and has_t1_toolhead_filament_sensor) or (has_t0_bowden_filament_sensor and has_t1_bowden_filament_sensor) %}
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=True
	RATOS_ECHO MSG="Spool joining enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Can not enable spool joining! No filament sensors found."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining deactivated!"
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining is not possible in copy and mirror mode!"
	{% endif %}

[gcode_macro _JOIN_SPOOL]
gcode = 
	
	{% set old_toolhead = params.TOOLHEAD|int %}
	{% set new_toolhead = 0 if old_toolhead == 1 else 1 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set purge_after_load = printer["gcode_macro T%s" % new_toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_JOIN_SPOOL" MSG="toolhead: {new_toolhead}"
	
	{% set has_filament = true %}
	{% set has_new_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% set has_new_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% if has_new_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	{% if has_new_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	
	{% if has_filament %}
	RATOS_ECHO MSG="Joining spools! Please wait for extruder to heat up...."
	
	
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={new_toolhead}
	
	
	_DEACTIVATE_TOOLHEAD TOOLHEAD={old_toolhead}
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set extruder_temp = extruder_first_layer_temp[new_toolhead]|float %}
	{% else %}
	{% set extruder_temp = extruder_other_layer_temp[new_toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if new_toolhead == 0 else 'extruder1'} TARGET={extruder_temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if new_toolhead == 0 else 'extruder1'} MINIMUM={extruder_temp}  MAXIMUM={extruder_temp + 5}
	
	
	{% if purge_after_load > 0 %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_toolhead == 0 else new_toolhead}
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={new_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={new_toolhead} E={purge_after_load}
	_CLEANING_MOVE TOOLHEAD={new_toolhead} AUTOMATED=True
	
	
	SET_DUAL_CARRIAGE CARRIAGE={old_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if old_toolhead == 0 else old_toolhead}
	
	{% endif %}
	
	
	RESUME TOOLHEAD={new_toolhead}
	
	
	_IDEX_JOIN_SPOOLS ENABLE=false
	
	{% else %}
	{ action_raise_error("Spool join failed! No filament found or filament sensor is disabled.") }
	{% endif %}

[gcode_macro REMAP_TOOLHEADS]
gcode = 
	
	{% set toolheads = params.TOOLHEADS|default("") %}
	
	{% if toolheads == "" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% else %}
	{% if toolheads != "0,1" and toolheads != "1,0" %}
	RATOS_ECHO MSG="Wrong toolhead configuration!"
	RATOS_ECHO MSG="Remap = REMAP_TOOLHEADS TOOLHEADS=0,1"
	RATOS_ECHO MSG="Deactivate = REMAP_TOOLHEADS TOOLHEADS="
	{% else %}
	{% if toolheads == "0,1" or toolheads == "1,0" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=true
	_IDEX_SINGLE
	{% else %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_REMAP_TOOLHEADS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	{% if not enable or (idex_mode != "copy" and idex_mode != "mirror") %}
	{% if enable %}
	RATOS_ECHO MSG="Toolhead remapping enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping deactivated!"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE={enable}
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping not possible in copy and mirror mode!"
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	{% endif %}

[gcode_macro SHAPER_CALIBRATE]
rename_existing = SHAPER_CALIBRATE_ORG
gcode = 
	RATOS_ECHO PREFIX="IDEX" MSG="SHAPER_CALIBRATE is useless on IDEX machines. Please use the GENERATE_SHAPER_GRAPHS macro and type the values into `variable_shaper_*_freq` and `variable_shaper_*_type manually`."

[gcode_shell_command generate_shaper_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-shaper-graph.sh
timeout = 120.
verbose = True

[gcode_shell_command generate_tension_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-belt-tension-graph.sh
timeout = 120.
verbose = True

[gcode_macro SET_PRESSURE_ADVANCE]
variable_snyc_toolheads = False
rename_existing = SET_PRESSURE_ADVANCE_BASE
gcode = 
	{% if params.SYNC_TOOLHEADS is defined %}
	{% set snyc_toolheads = true if params.SYNC_TOOLHEADS|default(false)|lower == 'true' else false %}
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=True
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="Syncing toolheads..."
	{% else %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' or snyc_toolheads %}
	{% set advance = params.ADVANCE|default(printer['extruder'].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['extruder'].smooth_time|float)|float %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T0"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T1"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder1' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% else %}
	{% set extruder = 'extruder' if act_t == 0 else 'extruder1' %}
	{% if params.EXTRUDER is defined %}
	{% set extruder = params.EXTRUDER %}
	{% endif %}
	{% if extruder == 'extruder' or extruder == 'extruder1' %}
	{% set advance = params.ADVANCE|default(printer['%s' % extruder].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['%s' % extruder].smooth_time|float)|float %}
	SET_PRESSURE_ADVANCE_BASE EXTRUDER={extruder} ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% if params.EXTRUDER is not defined %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG={"T%s" % act_t}
	{% endif %}
	{% else %}
	SET_PRESSURE_ADVANCE_BASE { rawparams }
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro M106]
rename_existing = M106.1
variable_swap_speed = -1
gcode = 
	
	{% set s = [[params.S|default(255)|int, 255]|min, 0]|max %}
	{% set p = params.P|default(-1)|int %}
	{% set speed = s / 255 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set t = 1 if idex_mode=='primary' else 0 %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(0)|int == 1 else false %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set sync_fans = true %}
	{% endif %}
	
	
	{% if sync_fans and idex_mode != "copy" and idex_mode != "mirror" %}
	
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int %}
	
	
	{% if toolshift_count > total_toolshifts %}
	{% set sync_fans = false %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE=-1
	
	
	{% if p == -1 %}
	
	{% if speed == 0 %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed}
	{% else %}
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE={speed}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={(speed if (t == 0 or sync_fans) else 0)}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={(speed if (t == 1 or sync_fans) else 0)}
	{% endif %}
	{% else %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed if t == p else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed if t == p else 0}
	{% endif %}
	
	
	M106.1 S{s}

[gcode_macro M107]
rename_existing = M107.1
gcode = 
	{% set p = params.P|default(-1)|int %}
	M106 S0 P{p}

[gcode_macro _SELECT_TOOL]
variable_last_timestamp = 0
gcode = 
	{% if params.T is defined %}
	{% set idex_mode = '' %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if "xyz" not in printer.toolhead.homed_axes and (idex_mode == "copy" or idex_mode == "mirror") %}
	_IDEX_SINGLE
	{% set idex_mode = 'reset' %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set new_t = params.T|int %}
	
	
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads and is_printing_gcode %}
	{% set new_t = 0 if new_t == 1 else 1 %}
	{% endif %}
	
	
	{% set toolchange_prepurging_timer = printer["gcode_macro RatOS"].toolchange_prepurging_timer|default(0)|int %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	DEBUG_ECHO PREFIX="_SELECT_TOOL" MSG="act_t: {act_t}, new_t: {new_t}, is_printing_gcode: {is_printing_gcode}, swap_toolheads: {swap_toolheads}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	{% set act_extruder = 'extruder%s' % ('' if new_t == 0 else new_t) %}
	{% if new_t != act_t or printer.toolhead.extruder != act_extruder or idex_mode == 'reset' %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Selecting T{new_t}.."
	
	
	M220 S100
	
	
	
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(1)|int == 1 else false %}
	
	
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set toolshift = false %}
	{% endif %}
	
	
	{% set fan_speed = printer["fan_generic part_fan_t%s" % act_t].speed %}
	
	
	{% set deactivate_toolhead = false %}
	{% if is_printing_gcode %}
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int + 1 %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE={toolshift_count}
	{% if toolshift_count == total_toolshifts %}
	{% set deactivate_toolhead = true %}
	{% endif %}
	{% endif %}
	
	
	{% set needs_wakeup = true if printer["gcode_macro T%s" % new_t].standby|default(false)|lower == 'true' else false %}
	
	
	{% set needs_purging = false %}
	{% set wake_up_purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% if is_printing_gcode and toolchange_prepurging_timer > 0 and wake_up_purge > 0 %}
	{% set new_timestamp = printer["print_stats"].print_duration %}
	{% set elapsed_time = new_timestamp - last_timestamp %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={new_timestamp}
	{% if elapsed_time > toolchange_prepurging_timer %}
	{% set needs_purging = true %}
	{% endif %}
	{% endif %}
	
	
	{% set first_use_purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% if toolshift_count == 1 and first_use_purge > 0 %}
	{% set needs_purging = true %}
	{% endif %}
	
	
	{% if is_printing_gcode and (toolchange_standby_temp > -1 or needs_purging or needs_wakeup) %}
	_TOOLHEAD_STANDBY TOOLHEAD={act_t}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	_TOOLHEAD_WAKEUP TOOLHEAD={new_t} X={new_x} Y={new_y} Z={new_z} FAN_SPEED={fan_speed} TOOLSHIFT_COUNT={toolshift_count}
	{% else %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(false)|lower == 'true' else false %}
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if (new_t == 0 or sync_fans) else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if (new_t == 1 or sync_fans) else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	_TOOLCHANGE T={new_t} X={new_x} Y={new_y} Z={new_z} PARK_T0={park_t0} PARK_T1={park_t1} TOOLSHIFT={toolshift}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[new_t]|float)} SHAPER_FREQ_Y={(shaper_y_freq[new_t]|float)} SHAPER_TYPE_X={(shaper_x_type[new_t]|lower)} SHAPER_TYPE_Y={(shaper_y_type[new_t]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if new_t == 0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if new_t == 1 else False}
	
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% set sanity_check_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if new_t == 0 %}
	{% if printer.toolhead.extruder == 'extruder' %}
	{% if sanity_check_idex_mode == 'primary' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% elif new_t == 1 %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% if sanity_check_idex_mode == 'inactive' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _TOOLHEAD_STANDBY]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Putting toolhead T{toolhead} into standby mode."
	DEBUG_ECHO PREFIX="_TOOLHEAD_STANDBY" MSG="toolhead: {toolhead}, config_z_hop: {config_z_hop}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={toolhead} SYNC=0
	PARK_TOOLHEAD
	
	
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={toolchange_standby_temp}
	{% endif %}
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=True
	{% endif %}
	
	
	_LED_TOOLHEAD_STANDBY TOOLHEAD={toolhead}

[gcode_macro _TOOLHEAD_WAKEUP]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set fan_speed = params.FAN_SPEED|float %}
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift_count = params.TOOLSHIFT_COUNT|default(0)|int %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% if toolshift_count == 1 %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% endif %}
	{% set needs_wakeup = true if printer["gcode_macro T%s" % toolhead].standby|default(false)|lower == 'true' else false %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Waking up toolhead T{toolhead}. Please wait for extruder to heat up..."
	DEBUG_ECHO PREFIX="_TOOLHEAD_WAKEUP" MSG="toolhead: {toolhead}, fan_speed: {fan_speed}, new_x: {new_x}, new_y: {new_y}, new_z: {new_z}, config_z_hop: {config_z_hop}"
	
	
	_LED_TOOLHEAD_WAKEUP TOOLHEAD={toolhead}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={toolhead} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE=1
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if toolhead == 0 else toolhead}
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if needs_wakeup %}
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set temp = extruder_first_layer_temp[toolhead]|float %}
	{% else %}
	{% set temp = extruder_other_layer_temp[toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if toolhead == 0 else 'extruder1'} MINIMUM={temp}  MAXIMUM={temp + 5}
	{% endif %}
	
	
	_LED_PRINTING TOOLHEAD={toolhead}
	
	
	{% if purge > 0 %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={toolhead} E={purge}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	
	
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if toolhead == 1 else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	G92 E0
	G1 E-{e} F{feedrate}
	G92 E0
	
	
	{% if new_x >= 0 and new_y >= 0 %}
	G1 X{new_x} Y{new_y} F{speed}
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={config_z_hop} T={toolhead} SYNC=0
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=False

[gcode_macro _TOOLCHANGE]
variable_toolshift_count = 0
gcode = 
	
	
	{% set new_t = params.T|default(-1)|int %}
	{% set new_x = params.X|default(-1.0)|float %}
	{% set new_y = params.Y|default(-1.0)|float %}
	{% set new_z = params.Z|default(-1.0)|float %}
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(true)|lower == 'true' else false %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T: {new_t}, X: {new_x}, Y: {new_y}, Z: {new_z}, PARK_T0: {park_t0}, PARK_T1: {park_t1}, IS_PRINTING_GCODE: {is_printing_gcode}, TOOLSHIFT: {toolshift}"
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	{% if park_t0 >= 0 and park_t1 >= 0 %}
	{% set parking_position_t0 = park_t0 %}
	{% set parking_position_t1 = park_t1 %}
	{% set parking_position_act_t = park_t0 if act_t == 0 else park_t1 %}
	{% endif %}
	
	
	{% if not is_printing_gcode and not toolshift %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Changing tool to T{new_t} without retracting/extruding or moving the toolheads except for parking."
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	G90
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% if not is_printing_gcode and toolshift and new_x < 0 and new_y < 0 %}
	{% set new_x = center_x %}
	{% set new_y = printer.gcode_move.gcode_position.y|float %}
	{% endif %}
	
	{% if new_x < 0 or new_y < 0 %}
	
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="No new X or Y position given, parking the active toolhead and activating the new toolhead without moving it."
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={new_t}
	
	
	{% if "x" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	{% if is_printing_gcode %}
	_EXTRUDE T={new_t}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	{% if "xyz" not in printer.toolhead.homed_axes %}
	
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	
	
	{% set svv = printer.save_variables.variables %}
	{% if new_t == default_toolhead %}
	{% set new_xoffset = 0 %}
	{% set new_yoffset = 0 %}
	{% set new_zoffset = 0 %}
	{% else %}
	{% set new_xoffset = -svv.idex_xoffset %}
	{% set new_yoffset = -svv.idex_yoffset %}
	{% set new_zoffset = -svv.idex_zoffset %}
	{% endif %}
	
	{% set xoffset_correction = new_xoffset - printer.named_offsets.toolhead_alignment.x %}
	{% set yoffset_correction = new_yoffset - printer.named_offsets.toolhead_alignment.y %}
	{% set zoffset_correction = new_zoffset - printer.named_offsets.toolhead_alignment.z %}
	
	{% if new_t == 0 %}
	
	{% set t0_act_x = parking_position_t0 %}
	{% set t1_act_x = printer.toolhead.position.x|float %}
	{% set t0_new_x = new_x %}
	{% set t1_new_x = parking_position_t1 %}
	{% set t0_distance = t0_new_x - t0_act_x %}
	{% set t1_distance = t1_new_x - t1_act_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T0."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	
	
	G1 X{t0_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x + (t1_new_x - t1_act_x)} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t0_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T0: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% elif new_t == 1 %}
	
	{% set t0_act_x = printer.toolhead.position.x|float %}
	{% set t1_act_x = parking_position_t1 %}
	{% set t0_new_x = parking_position_t0 %}
	{% set t1_new_x = new_x %}
	{% set t0_distance = t0_act_x - t0_new_x %}
	{% set t1_distance = t1_act_x - t1_new_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T1."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x - t1_distance + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t1_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T1: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% endif %}
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	{% endif %}

[gcode_macro _ZHOP_BEFORE_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_hop = params.Z_HOP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_HOP: {z_hop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="COMBINED_ZHOP G1 Z+{z_hop} E-{e} F{speed * 60}"
	G1 Z+{z_hop} E-{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="ZHOP G1 Z+{z_hop} F{speed * 60}"
	G1 Z+{z_hop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="RETRACT G1 E-{e} F{feedrate}"
	G1 E-{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _ZDROP_AFTER_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_drop = params.Z_DROP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_DROP: {z_drop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="COMBINED_ZDROP G1 Z-{z_drop} E{e} F{speed * 60}"
	G1 Z-{z_drop} E{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="ZDROP G1 Z-{z_drop} F{speed * 60}"
	G1 Z-{z_drop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="EXTRUDE G1 E{e} F{feedrate}"
	G1 E{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _EXTRUDE]
gcode = 
	
	{% set t = params.T|int %}
	
	
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	
	DEBUG_ECHO PREFIX="_EXTRUDE" MSG="G1 E{e} F{feedrate * 60}"
	
	
	G91
	M82
	G92 E0
	G1 E{e} F{feedrate * 60}
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _DEACTIVATE_TOOLHEAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_DEACTIVATE_TOOLHEAD" MSG="TOOLHEAD {toolhead}"
	
	
	{% if toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% endif %}
	
	
	M106.1 S0
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={toolhead}

[delayed_gcode _INIT_TOOLHEADS]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	_IDEX_SINGLE INIT=1
	
	
	{% if printer.fastconfig.settings.dual_carriage.safe_distance is defined %}
	{% if printer.fastconfig.settings.dual_carriage.safe_distance|float < 50 %}
	{ action_emergency_stop("Dual carriage safe_distance seems to be too low!") }
	{% endif %}
	{% else %}
	{ action_emergency_stop("Dual carriage safe_distance not defined!") }
	{% endif %}

[gcode_macro _SET_TOOLHEAD_OFFSET]
description = "Internal use only. Sets the toolhead_alignment offset (and hotend_thermal_expansion offset when configured) for the active/dominant toolhead."
gcode = 
	
	{% set move = params.MOVE|default(0)|int %}
	{% set force_toolhead = params.FORCE_TOOLHEAD|default(-1)|int %}
	
	
	{% if params.T is defined %}
	CONSOLE_ECHO TYPE="error" MSG="_SET_TOOLHEAD_OFFSET called with deprectated T parameter, which is ignored."
	{';$_SET_TOOLHEAD_OFFSET_ignoring_TOOLHEAD_parameter'}
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="active/dominant toolhead: {toolhead}, MOVE: {move}, FORCE_TOOLHEAD: {force_toolhead}"
	
	
	{% if force_toolhead >= 0 %}
	{% set toolhead = force_toolhead %}
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="FORCE_TOOLHEAD applied, using TOOLHEAD: {toolhead}"
	{% endif %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set move = 0 %}
	{% endif %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|int %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X=0 Y=0 MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z=0 MOVE={move} SPEED={z_speed}
	{% else %}
	{% set svv = printer.save_variables.variables %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X={(-svv.idex_xoffset)} Y={(-svv.idex_yoffset)} MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-svv.idex_zoffset)} MOVE={move} SPEED={z_speed}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}

[gcode_macro TOOLSHIFT_CONFIG]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={params.SPEED|default(300)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={params.ACCEL|default(5000)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_retraction VALUE={params.RETRACT|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_extrusion VALUE={params.EXTRUDE|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_feedrate VALUE={params.FEEDRATE|default(7200)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={params.Z_HOP|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zspeed VALUE={params.Z_SPEED|default(25)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_combined_zhop VALUE={true if params.COMBINED_ZHOP|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_sync_fans VALUE={true if params.SYNC_FANS|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_prepurging_timer VALUE={params.AUTO_PURGE_TIME|default(0)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_purge VALUE={params.PURGE|default(25)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_standby_temp VALUE={params.STANDBY_TEMP|default(-1)|float}

[gcode_macro CALCULATE_DC_ENDSTOP]
description = "DEPRECATED: This macro has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."
gcode = 
	CONSOLE_ECHO TITLE="CALCULATE_DC_ENDSTOP has been deprecated" TYPE="error" MSG="The CALCULATE_DC_ENDSTOP has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."

[gcode_macro _VAOC]
variable_is_fixed = True
variable_is_started = False
variable_is_started_at_temp = False
variable_additional_safe_distance = 50
variable_safe_z = 30
variable_auto_z_offset_calibration = True
variable_enable_camera_cooling = True
variable_camera_cooling_fan_speed = 0.3
variable_camera_cooling_temperature = 50
variable_toolchange_travel_speed = 300
variable_toolchange_travel_accel = 5000
variable_adjusting_secondary_toolhead_focus_adjusts_zoffset = False
variable_cache_toolchange_travel_speed = 300
variable_cache_toolchange_travel_accel = 5000
variable_cache_toolchange_zhop = 1.0
variable_t0_toolhead_sensor_enabled = 0
variable_t1_toolhead_sensor_enabled = 0
variable_t0_bowden_sensor_enabled = 0
variable_t1_bowden_sensor_enabled = 0
variable_loaded_skew_profile = ""
variable_gcode_z_offset = 0.0
variable_start_x_offset = 0.0
variable_start_y_offset = 0.0
gcode = 
	_ECHO_VAOC_VARS
variable_expected_camera_x_position = 212.5
variable_expected_camera_y_position = 530.5

[gcode_macro _VAOC_START]
description = Called from the front end. If T0_TEMP, T1_TEMP and BED_TEMP parameter are specified, VAOC calibration will start under real conditions at printing temp.
gcode = 
	
	{% set t0_temp = params.T0_TEMP|default(0)|int %}
	{% set t1_temp = params.T1_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(0)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro SKEW_PROFILE"].loaded_profile|default("") %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=loaded_skew_profile VALUE='"{loaded_skew_profile}"'
	
	
	{% if t0_temp > 0 and t1_temp > 0 and bed_temp > 0 %}
	
	
	{% if not is_fixed %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("VAOC calibration at temp works only with a fixed installed VAOC device.") }
	{% endif %}
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE=0
	{% endif %}
	
	
	START_PRINT EXTRUDER_TEMP={t0_temp},{t1_temp} EXTRUDER_OTHER_LAYER_TEMP={t0_temp},{t1_temp} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp} INITIAL_TOOL=0 TOTAL_LAYER_COUNT=1 X0={(printable_x_max / 2 - 10)} Y0={(printable_y_max / 2 - 10)} X1={(printable_x_max / 2 + 10)} Y1={(printable_y_max / 2 + 10)} TOTAL_TOOLSHIFTS=1 FIRST_X={printable_x_max / 2} FIRST_Y={printable_y_max / 2} MIN_X={(printable_x_max / 2 - 10)} MAX_X={(printable_x_max / 2 + 10)} USED_TOOLS=0,1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=True
	
	{% endif %}
	
	
	_START_VAOC

[gcode_macro _START_VAOC]
description = Called from _VAOC_START. Do not call it manually.
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(printable_x_max/2)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(printable_y_max/2)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	DEBUG_ECHO PREFIX="VAOC_START" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, zcontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_x_offset VALUE={svv.idex_xoffset|default(0.0)|float}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_y_offset VALUE={svv.idex_yoffset|default(0.0)|float}
	
	
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_SAFE_Z_HEIGHT
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_speed VALUE={printer["gcode_macro RatOS"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_accel VALUE={printer["gcode_macro RatOS"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_zhop VALUE={printer["gcode_macro RatOS"].toolchange_zhop|float}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE=0
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"START X_REFERENCE:%.6f Y_REFERENCE:%.6f Z_REFERENCE:%.6f PARK_T0:%.6f PARK_T1:%.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, parking_position_t0, parking_position_t1)}
	
	
	_LED_VAOC_ON
	
	
	
	
	
	
	
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=gcode_z_offset VALUE={printer.gcode_move.homing_origin.z}
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z=0
	
	
	MAYBE_HOME
	M400
	
	
	_LOAD_RATOS_SKEW_PROFILE
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	IDEX_SINGLE
	{% endif %}
	
	
	
	SAVE_GCODE_STATE NAME=vaoc_state
	
	
	RESET_NAMED_OFFSET EVENT=reset_all
	
	
	{% if is_fixed %}
	_SELECT_TOOL T=0 TOOLSHIFT=false
	{% if default_toolhead == 0 %}
	G1 X{idex_xcontrolpoint} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint + safe_distance + additional_safe_distance} F{speed}
	{% else %}
	G1 X{idex_xcontrolpoint - safe_distance - additional_safe_distance} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint} F{speed}
	{% endif %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	{% else %}
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	G1 X{idex_xcontrolpoint} F{speed}
	G1 Y{idex_ycontrolpoint} F{speed}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	
	
	_SELECT_TOOL T={default_toolhead} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	{% if not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={default_toolhead}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=True

[gcode_macro _VAOC_END]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_y = printable_y_max / 2 %}
	{% set saved_gcode_z_offset = printer["gcode_macro _VAOC"].gcode_z_offset|default(0.0)|float %}
	
	DEBUG_ECHO PREFIX="_VAOC_END" MSG="printable_y_max: {printable_y_max}, center_y: {center_y}, safe_z: {safe_z}"
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% set x_offset_change = svv.idex_xoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_x_offset|default(0.0)|float %}
	{% set y_offset_change = svv.idex_yoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_y_offset|default(0.0)|float %}
	{% set offset_change_norm = (x_offset_change ** 2 + y_offset_change ** 2) ** 0.5 %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="VAOC calibration changed the relative XY offset between T0 and T1 by {offset_change_norm|round(3)} mm (ΔX: {x_offset_change|round(3)}, ΔY: {y_offset_change|round(3)})"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	G1 Y{center_y} F{speed}
	
	
	_IDEX_SINGLE INIT=1
	
	
	_LED_VAOC_OFF
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={printer["gcode_macro _VAOC"].cache_toolchange_zhop|float}
	
	
	{% if printer["gcode_macro _VAOC"].is_started_at_temp|default(true)|lower == 'true' %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_bowden_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_bowden_sensor_enabled|int}
	{% endif %}
	{% endif %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro _VAOC"].loaded_skew_profile|default("") %}
	{% if loaded_skew_profile != "" %}
	SKEW_PROFILE LOAD={loaded_skew_profile}
	{% else %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=vaoc_state
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z={saved_gcode_z_offset}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False

[gcode_macro _VAOC_LOAD_TOOL]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set auto_temp_offset = true if params.AUTO_TEMP_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set toolhead_zoffset = svv.idex_zoffset|default(0)|float %}
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move T%s to control point: X%.6f Y%.6f Z%.6f IS_FIXED=%s"' % (t, idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, is_fixed)}
	
	
	{% if not auto_temp_offset and not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={t}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	{% set current_z = printer.toolhead.position.z|float %}
	{% set lowest_toolhead_z = [current_z, current_z - toolhead_zoffset]|min %}
	{% if lowest_toolhead_z < safe_z %}
	G1 Z{[safe_z, safe_z + toolhead_zoffset]|max} F{z_speed}
	{% else %}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	{% endif %}
	
	
	_SELECT_TOOL T={t} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_SET_CAMERA_COOLING]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	
	
	{% set enable_camera_cooling = true if printer["gcode_macro _VAOC"].enable_camera_cooling|default(true)|lower == 'true' else false %}
	{% set camera_cooling_temperature = printer["gcode_macro _VAOC"].camera_cooling_temperature|float %}
	{% set camera_cooling_fan_speed = printer["gcode_macro _VAOC"].camera_cooling_fan_speed|float %}
	
	
	{% if printer.heater_bed.temperature >= camera_cooling_temperature and enable_camera_cooling %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={camera_cooling_fan_speed if t == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={camera_cooling_fan_speed if t == 1 else 0}
	
	
	M106.1 S{camera_cooling_fan_speed}
	
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	{% endif %}

[gcode_macro _VAOC_SET_TOOL]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="_VAOC_SET_TOOL" MSG="IDEX_MODE: {idex_mode}, TOOLHEAD: {toolhead}"
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	{% set x = printer.gcode_move.gcode_position.x|float %}
	{% set y = printer.gcode_move.gcode_position.y|float %}
	{% set z = printer.gcode_move.gcode_position.z|float %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE={x}
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE={y}
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE={z}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Control point was set: X%.6f Y%.6f Z%.6f"' % (x, y, z)}
	
	{% else %}
	
	
	
	{% set move_diff_x = printer.gcode_move.gcode_position.x|float - svv.idex_xcontrolpoint|float %}
	{% set move_diff_y = printer.gcode_move.gcode_position.y|float - svv.idex_ycontrolpoint|float %}
	{% set move_diff_z = printer.gcode_move.gcode_position.z|float - svv.idex_zcontrolpoint|float %}
	
	
	{% set new_x_offset = svv.idex_xoffset - move_diff_x %}
	{% set new_y_offset = svv.idex_yoffset - move_diff_y %}
	{% set new_z_offset = svv.idex_zoffset - move_diff_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE={new_x_offset}
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE={new_y_offset}
	
	{% set z_focus_msg = "" %}
	{% if move_diff_z|abs > 1e-6 %}
	{% if printer["gcode_macro _VAOC"].adjusting_secondary_toolhead_focus_adjusts_zoffset|default(false)|lower == 'true' %}
	{% set z_focus_msg = " (Z offset adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={new_z_offset}
	{% else %}
	{% set z_focus_msg = " (Z offset not adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	{% set new_z_offset = svv.idex_zoffset %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset was set: X%.6f Y%.6f Z%.6f%s"' % (toolhead, new_x_offset, new_y_offset, new_z_offset, z_focus_msg)}
	
	{% endif %}

[gcode_macro _VAOC_MOVE]
gcode = 
	
	{% set x = params.X|default(0)|float %}
	{% set y = params.Y|default(0)|float %}
	{% set z = params.Z|default(0)|float %}
	
	
	G91
	{% if z != 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 Z%.6f F300"' % (z)}
	G1 Z{z} F300
	
	{% else %}
	{% if x <=2 and y <=2 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 X%.6f Y%.6f F18000"' % (x, y)}
	G1 X{x} Y{y} F18000
	{% endif %}
	{% endif %}
	G90

[gcode_macro _VAOC_CALIBRATE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	{% if printer["z_offset_probe"] is defined and is_started %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	
	{% if auto_z_offset %}
	_START_VAOC AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_END
	{% else %}
	_VAOC_LOAD_TOOL T={default_toolhead}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	{% endif %}
	
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_Z_OFFSET
	
	{% endif %}

[gcode_macro _VAOC_PROBE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}
	{% if not auto_z_offset %}
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	{% endif %}
	M400
	_VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT

[gcode_macro _VAOC_Z_OFFSET_PROBE_CURRENT_POSITION]
gcode = 
	
	Z_OFFSET_PROBE PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_DROP=1 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median

[gcode_macro _VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT]
gcode = 
	{% if printer["z_offset_probe"] is defined %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE={last_z}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Z-offset control point set:: %.6f"' % last_z}
	
	{% else %}
	
	
	
	{% set z = svv.idex_zoffsetcontrolpoint|float - last_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={z}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-z)}
	
	
	G0 Z{svv.idex_zcontrolpoint|float} F{z_speed}
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset set: Z %.6f"' % (t, z)}
	
	{% endif %}
	
	{% endif %}

[gcode_macro _VAOC_ECHO_Z_OFFSET]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s toolhead z-offset %.6f"' % (1 if default_toolhead == 0 else 0, svv.idex_zoffset)}
	{% if svv.idex_zoffset|abs < 0.02 %}
	CONSOLE_ECHO TITLE={'"Perfect toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="You have a perfect toolhead z-offset!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.02 and svv.idex_zoffset|abs < 0.05 %}
	CONSOLE_ECHO TITLE={'"Good toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is good!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.05 and svv.idex_zoffset|abs < 0.1 %}
	CONSOLE_ECHO TITLE={'"High toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset could be better._N_Use minimum 0.3mm first layer height for copy and mirror mode prints." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.1 and svv.idex_zoffset|abs < 0.2 %}
	CONSOLE_ECHO TITLE={'"Bad toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is bad._N_Copy and mirror mode prints are not recommended with it." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.2 %}
	CONSOLE_ECHO TITLE={'"Unacceptable toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is unacceptable._N_Do not print in copy and mirror mode with it." TYPE="alert"
	{% endif %}
	RATOS_ECHO PREFIX="VAOC" MSG="Toolhead z-offset calibration done!"

[gcode_macro _VAOC_CALIBRATE_TEMP_OFFSET]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if is_fixed and is_started and printer["z_offset_probe"] is defined and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	_VAOC_LOAD_TOOL T={default_toolhead} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_NOZZLE_TEMP_OFFSETS
	
	{% endif %}

[gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET=0
	
	
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	M400

[gcode_macro _VAOC_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(150)|float %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Probing with nozzle temperature {temp}°C..."
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	
	
	G0 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _VAOC_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set msg = '"T0 expansion coefficient %.6fmm_N_T1 expansion coefficient %.6fmm"' % (svv.nozzle_expansion_coefficient_t0, svv.nozzle_expansion_coefficient_t1) %}
	CONSOLE_ECHO TITLE="Nozzle expansion coefficients:" MSG={msg} TYPE="success"

[gcode_macro _VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - expected_camera_x_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC x-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_xcontrolpoint, expected_camera_x_position)) }
	{% endif %}
	{% if (idex_ycontrolpoint - expected_camera_y_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC y-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_ycontrolpoint, expected_camera_y_position)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - printer.gcode_move.gcode_position.x|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected y-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_xcontrolpoint, printer.gcode_move.gcode_position.x|float)) }
	{% endif %}
	{% if (idex_ycontrolpoint - printer.gcode_move.gcode_position.y|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected x-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_ycontrolpoint, printer.gcode_move.gcode_position.y|float)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_SAFE_Z_HEIGHT]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set idex_zoffsetcontrolpoint = svv.idex_zoffsetcontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_SAFE_Z_HEIGHT" MSG={'"idex_zcontrolpoint: %.6f, idex_zoffsetcontrolpoint: %.6f"' % (idex_zcontrolpoint, idex_zoffsetcontrolpoint)}
	
	{% if safe_z < idex_zcontrolpoint + 2 or safe_z < idex_zoffsetcontrolpoint + 2 %}
	{action_raise_error("VAOC safe_z value (%.3f) is too low, it must be higher than %.3f" % (safe_z, [idex_zoffsetcontrolpoint + 2, idex_zcontrolpoint + 2]|max))}
	{% endif %}

[gcode_macro _VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED]
gcode = 
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T0. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T1. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_RESET]
gcode = 
	DEBUG_ECHO PREFIX="_VAOC_RESET" MSG="running template-emitted _VAOC_RESET macro"
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE=212.5
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE=530.5
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE=10
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE=0
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE=0.0
	
	RESET_DC_ENDSTOP_CONFIGURATION
	RESET_Y_MAX_ADJUSTMENT
	
	
	CONSOLE_ECHO TITLE="VAOC Configuration Reset" MSG="VAOC configuration has been reset. You must RESTART klipper for the changes to take effect,_N_then re-calibrate VAOC."

[gcode_macro _ECHO_VAOC_VARS]
description = Echo VAOC variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro _VAOC"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro _VAOC_SWITCH_LED]
gcode = 
	{% if params.STATE|default(0)|int == 1 %}
	_LED_VAOC_ON
	{% else %}
	_LED_VAOC_OFF
	{% endif %}

[gcode_macro Z_PROBE_TEST_T0]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T0
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST_T1]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T1
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	
	
	_VAOC_Z_PROBE_TEST_EVALUATE
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro _VAOC_Z_PROBE_LOOP]
gcode = 
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_SHAKE_IT
	_VAOC_START

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if primary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T0. Retried {primary_retries} time(s)."
	{% endif %}
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	
	{% if (primary_range - secondary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 is drifting significantly more than T1."
	{% endif %}
	{% if (secondary_range - primary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 is drifting significantly more than T0."
	{% endif %}
	
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T0]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T1]
gcode = 
	
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _SHAKE_IT]
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	_Z_HOP
	{% for i in range(3) %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 + 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 + 1}
	{% endfor %}
	{% for i in range(2) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 + 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 + 50}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 1}
	{% endfor %}
	{% endfor %}

[gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 retries updated: {new_retries}"

[gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 retries updated: {new_retries}"

[gcode_macro _CLEAR_PRIMARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _CLEAR_SECONDARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _VAOC_TEST_Z_OFFSET]
gcode = 
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}

[delayed_gcode _IDEX_INIT]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	VERIFY_HYBRID_INVERTED

[gcode_macro Z_TILT_ADJUST]
rename_existing = Z_TILT_ADJUST_ORIG
gcode = 
	
	{% set beacon_contact_z_tilt_adjust_samples = printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust_samples|default(2)|int %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(true)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	_IDEX_SINGLE
	
	_SELECT_TOOL T={printer["gcode_macro RatOS"].default_toolhead|default(0)|int} TOOLSHIFT=false
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_tilt_adjust %}
	Z_TILT_ADJUST_ORIG PROBE_METHOD=contact SAMPLES={beacon_contact_z_tilt_adjust_samples}
	{% else %}
	Z_TILT_ADJUST_ORIG
	{% endif %}
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if idex_mode == "copy" %}
	_IDEX_COPY
	{% elif idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[stepper_x]
position_max = 500
position_endstop = -59.6
position_min = -59.6
step_pin = PF13
dir_pin = x_dir_pin
enable_pin = !PF14
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t0:PA2

[stepper_y]
position_max = 533.65
position_min = -14.35
position_endstop = -14.35
step_pin = PG0
dir_pin = !y_dir_pin
enable_pin = !PF15
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = PG9

[stepper_z]
position_max = 500
position_min = -7
step_pin = PC13
dir_pin = !z0_dir_pin
enable_pin = !PF1
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4
homing_speed = 10
endstop_pin = probe:z_virtual_endstop

[z_tilt]
z_positions = 
	0,0
	250,500
	500,0
points = 
	20, 10
	480, 230
	20, 450
horizontal_move_z = 20
retries = 10
retry_tolerance = 0.02
speed = 600

[extruder]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t0:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t0:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t0:PD3
dir_pin = toolboard_t0:e_dir_pin
enable_pin = !toolboard_t0:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[firmware_retraction]
retract_speed = 60
unretract_extra_length = 0
unretract_speed = 60
retract_length = 0.2

[extruder1]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t1:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t1:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t1:PD3
dir_pin = toolboard_t1:e_dir_pin
enable_pin = !toolboard_t1:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[resonance_tester]
accel_chip_x = lis2dw toolboard_t0
accel_chip_y = lis2dw toolboard_t0
probe_points = 
	250,250,20

[tmc5160 stepper_x]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC4
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 dual_carriage]
stealthchop_threshold = 0
interpolate = True
cs_pin = PF2
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y]
stealthchop_threshold = 0
interpolate = True
cs_pin = PD11
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y1]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC7
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[stepper_y1]
step_pin = PG4
dir_pin = y1_dir_pin
enable_pin = !PA2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46

[tmc2209 stepper_z]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE4
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[tmc2209 stepper_z1]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE1
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z1]
step_pin = PE2
dir_pin = !z1_dir_pin
enable_pin = !PD4
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 stepper_z2]
stealthchop_threshold = 0
interpolate = True
uart_pin = PD3
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z2]
step_pin = PE6
dir_pin = !z2_dir_pin
enable_pin = !PE0
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 extruder]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t0:PB3
run_current = 0.707
sense_resistor = 0.11

[tmc2209 extruder1]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t1:PB3
run_current = 0.707
sense_resistor = 0.11

[beacon]
serial = /dev/beacon
x_offset = 0
y_offset = 27.5
mesh_main_direction = x
mesh_runs = 1
mesh_cluster_size = 0
speed = 15.
lift_speed = 80.
contact_max_hotend_temperature = 275
contact_mesh_min = 20,20
contact_mesh_max = 480,480

[beacon_user_z_offset]

[beacon_mesh]

[beacon_true_zero_correction]

[beacon_adaptive_heat_soak]

[delayed_gcode _BEACON_INIT]
initial_duration = 1
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	_BEACON_MESH_INIT
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_coefficient_multiplier
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_applied_offset
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=beacon_saved_runtime_offset
	{% if printer["gcode_macro RatOS"].beacon_contact_expansion_multiplier is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_contact_expansion_multiplier is no longer used, please remove it from your config file."
	{% endif %}
	{% if printer["gcode_macro RatOS"].beacon_scan_compensation_resolution is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_scan_compensation_resolution is no longer used, please remove it from your config file."
	{% endif %}

[gcode_macro BEACON_RATOS_CALIBRATION]
gcode = 
	RATOS_ECHO MSG="Did you mean BEACON_RATOS_CALIBRATE?"

[gcode_macro BEACON_RATOS_CALIBRATE]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	BEACON_INITIAL_CALIBRATION _AUTOMATED=True
	
	{% if beacon_contact_start_print_true_zero %}
	BEACON_POKE_TEST _AUTOMATED=True
	_BEACON_CHECK_POKE
	{% if printer["dual_carriage"] is not defined %}
	BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET _AUTOMATED=True
	{% endif %}
	{% endif %}
	
	{% set already_heated = False %}
	
	
	{% if beacon_contact_start_print_true_zero and beacon_scan_compensation_enable %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% set already_heated = True %}
	{% endif %}
	
	
	BEACON_FINAL_CALIBRATION _AUTOMATED=True _AUTOMATED_ALREADY_HEATED={already_heated} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	{% if beacon_contact_start_print_true_zero %}
	{% if printer["dual_carriage"] is not defined %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	_BEACON_ECHO_POKE
	{% endif %}
	RATOS_ECHO MSG="Beacon calibration finished!"
	
	
	_LED_BEACON_CALIBRATION_END
	
	
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG

[gcode_macro BEACON_INITIAL_CALIBRATION]
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Initial beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro BEACON_FINAL_CALIBRATION]
description = Runs BEACON_AUTO_CALIBRATE after heating the bed and chamber to specified temperatures. This creates a beacon model under reference conditions for future use.
	This macro will skip calibration if both the beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero settings are enabled, because a new
	model will be calibrated automatically at the start of each print. Use FORCE=True to override this check.
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set already_heated = true if params._AUTOMATED_ALREADY_HEATED|default(false)|lower == 'true' else false %}
	{% set force = params.FORCE|default('false')|lower in ('1', 'true', 'yes') %}
	
	
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default('false')|lower == "true" %}
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero and not force %}
	RATOS_ECHO MSG="BEACON_FINAL_CALIBRATION skipped, not needed because beacon_contact_calibrate_model_on_true_zero is enabled. Use FORCE=True to override."
	{% else %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	{% if chamber_temp > 0 and not already_heated %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	{% if not already_heated %}
	
	G0 Z2.5 F{z_hop_speed}
	
	
	RATOS_ECHO MSG="Waiting for calibration temperature..."
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	{% if beacon_adaptive_heat_soak %}
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,3600]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_Z_HOP
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Final beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	{% endif %}

[gcode_macro BEACON_POKE_TEST]
variable_poke_result_1 = -1
variable_poke_result_2 = -1
variable_poke_result_3 = -1
variable_poke_result_4 = -1
variable_poke_result_5 = -1
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_1 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_2 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_3 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_4 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_5 VALUE=-1
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G0 Z5 F{z_hop_speed}
	
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=1
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=2
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=3
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=4
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=5
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Beacon poke test finished!"
	{% if not automated %}
	_BEACON_ECHO_POKE
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro _BEACON_PROBE_POKE]
gcode = 
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	BEACON_POKE speed=3 top=5 bottom={poke_bottom}
	BEACON_QUERY

[gcode_macro _BEACON_STORE_POKE]
gcode = 
	
	{% set i = params.I|default(1)|int %}
	
	
	{% set last_z = printer.beacon.last_poke_result|default(0)|float %}
	
	
	{% if printer.beacon.last_poke_result|lower != "none" %}
	{% if printer.beacon.last_poke_result.error == 0 %}
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE={"poke_result_%s" % i} VALUE={printer.beacon.last_poke_result.latency}
	{% endif %}
	{% endif %}

[gcode_macro _BEACON_CHECK_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% if p1 == -1 or p2 == -1 or p3 == -1 or p4 == -1 or p5 == -1 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test error!") }
	{% endif %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	{% if avg > 6 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test failed!") }
	{% endif %}

[gcode_macro _BEACON_ECHO_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	
	
	{% if avg <= 1 %}
	{% set type = "success" %}
	{% set note = "Extremely low noise, rarely achieved" %}
	{% elif avg > 1 and avg <= 4 %}
	{% set type = "info" %}
	{% set note = "Excellent performance for a typical printer" %}
	{% elif avg > 4 and avg <= 8 %}
	{% set type = "warning" %}
	{% set note = "Acceptable performance, machine may have considerable cyclic axis noise" %}
	{% elif avg > 8 and avg <= 11 %}
	{% set type = "alert" %}
	{% set note = "Not ideal, may want to verify proper mounting or use thinner stackups" %}
	{% elif avg > 11 %}
	{% set type = "alert" %}
	{% set note = "Reason for concern, present setup may be risky to continue with" %}
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon poke test result:" TYPE={type} MSG={'"Average latency: %.2f_N_%s"' % (avg, note)}

[gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Nozzle temperature offset calibration..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET=0
	
	
	{% if not automated %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing with nozzle temperature {temp}°C..."
	PROBE PROBE_METHOD=contact PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median
	BEACON_QUERY
	
	
	G0 Z5 F{z_speed}

[gcode_macro _BEACON_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer.beacon.last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{default_toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% if default_toolhead == 0 %}
	CONSOLE_ECHO TYPE="info" MSG={'"T0 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t0}
	{% else %}
	CONSOLE_ECHO TYPE="info" MSG={'"T1 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t1}
	{% endif %}

[gcode_macro _BEACON_SET_NOZZLE_TEMP_OFFSET]
description = "Set the thermal expansion z offset for the active toolhead based on the current extruder target temperature and thermal expansion coefficient."
gcode = 
	{% if params.RESET is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The RESET parameter is no longer supported and has no effect."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% if params.TOOLHEAD is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The TOOLHEAD parameter is no longer supported and has no effect. The macro now automatically determines the current toolhead."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	{% if beacon_contact_expansion_compensation %}
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set nozzle_expansion_coefficient_t0 = svv.nozzle_expansion_coefficient_t0|default(0)|float %}
	{% if printer["dual_carriage"] is defined %}
	{% set nozzle_expansion_coefficient_t1 = svv.nozzle_expansion_coefficient_t1|default(0)|float %}
	{% endif %}
	
	
	{% set temp = printer['extruder' if toolhead == 0 else 'extruder1'].target|float %}
	
	
	{% set temp_delta = temp - beacon_contact_true_zero_temp %}
	{% set expansion_coefficient = nozzle_expansion_coefficient_t0 if toolhead == 0 else nozzle_expansion_coefficient_t1 %}
	{% set expansion_offset = temp_delta * (expansion_coefficient / 100) %}
	
	
	SET_NAMED_OFFSET NAME=hotend_thermal_expansion Z={expansion_offset} MOVE=1 MOVE_SPEED={z_speed}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG={'"Nozzle expansion offset of %.6fmm applied to T%s"' % (expansion_offset, toolhead)}
	DEBUG_ECHO PREFIX="_BEACON_SET_NOZZLE_TEMP_OFFSET" MSG="toolhead: {toolhead}, coefficient: {expansion_coefficient|round(6)}, temp_delta: {temp_delta|round(1)},  expansion_offset: {expansion_offset|round(6)}"
	
	{% endif %}

[gcode_macro BEACON_MEASURE_BEACON_OFFSET]
variable_needs_compensation = False
variable_reference_z = 0.0
variable_front = 0.0
variable_front_left = 0.0
variable_front_right = 0.0
variable_back = 0.0
variable_back_left = 0.0
variable_back_right = 0.0
variable_right = 0.0
variable_left = 0.0
variable_margin_x = 40
variable_margin_y = 40
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=False
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Measure beacon offset..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="center"
	
	
	G0 X{margin_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_left"
	
	
	G0 X{safe_home_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front"
	
	
	G0 X{(printable_x_max - margin_x)} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_right"
	
	
	G0 X{safe_home_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back"
	
	
	G0 X{margin_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_left"
	
	
	G0 X{margin_x} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="left"
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_BEACON_ECHO_BEACON_OFFSET
	
	
	_LED_BEACON_CALIBRATION_END
	
	{% endif %}

[gcode_macro _BEACON_STORE_BEACON_OFFSET]
gcode = 
	
	{% set location = params.LOCATION|lower %}
	
	
	{% set last_z = printer.beacon.last_offset_result["delta"]|default(0)|float %}
	
	
	{% if location == "center" %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE={location} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_BEACON_OFFSET]
gcode = 
	
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float * 1000 %}
	{% set front_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_left|default(0)|float * 1000 %}
	{% set front = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front|default(0)|float * 1000 %}
	{% set front_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_right|default(0)|float * 1000 %}
	{% set right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].right|default(0)|float * 1000 %}
	{% set back_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_right|default(0)|float * 1000 %}
	{% set back = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back|default(0)|float * 1000 %}
	{% set back_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_left|default(0)|float * 1000 %}
	{% set left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].left|default(0)|float * 1000 %}
	
	{% set line_1 = "Front left:    %.6fμm" % (front_left) %}
	{% set line_2 = "Front center:  %.6fμm" % (front) %}
	{% set line_3 = "Front right:   %.6fμm" % (front_right) %}
	{% set line_4 = "Left center:   %.6fμm" % (left) %}
	{% set line_5 = "Right center:  %.6fμm" % (right) %}
	{% set line_6 = "Back left:     %.6fμm" % (back_left) %}
	{% set line_7 = "Back center:   %.6fμm" % (back) %}
	{% set line_8 = "Back right:    %.6fμm" % (back_right) %}
	
	{% set max_value = [(front_left|abs), (front|abs), (front_right|abs), (left|abs), (right|abs), (back_left|abs), (back|abs), (back_right|abs)]|max %}
	{% if max_value <= 50 %}
	{% set type = "success" %}
	{% set recommendation = "Very low beacon offset: %.6fμm._N_No beacon scan compensation needed." % max_value %}
	{% elif max_value > 50 and max_value <= 100 %}
	{% set type = "info" %}
	{% set recommendation = "Low beacon offset: %.6fμm._N_You may experience first layer inconsistensies, consider beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 100 and max_value <= 150 %}
	{% set type = "warning" %}
	{% set recommendation = "High beacon offset: %.6fμm._N_High chance of first layer problems, beacon scan compensation is highly encouraged." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 150 and max_value <= 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Very High beacon offset: %.6fμm._N_You will encounter first layer problems on large prints unless you activate beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Extremely high beacon offset: %.6fμm._N_You have significant scan/contact inconsistency which is indicative of mechanical problems, please investigate before resorting to software compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon offset relative to the center" TYPE={type} MSG={'"_N_%s_N__N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s"' % (recommendation, line_1, line_2, line_3, line_4, line_5, line_6, line_7, line_8)}

[gcode_macro BEACON_CREATE_SCAN_COMPENSATION_MESH]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set profile = params.PROFILE|default("auto")|string %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set keep_temp_meshes = params.KEEP_TEMP_MESHES|default(0) %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' %}
	{% set desired_spacing = printer["gcode_macro RatOS"].beacon_scan_compensation_desired_spacing|float %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	
	{% if not beacon_scan_compensation_enable %}
	RATOS_ECHO MSG="Beacon scan compensation is disabled!"
	
	{% else %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	
	
	RATOS_ECHO MSG="Please wait..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	G1 Z2.5 F{z_speed}
	{% if beacon_adaptive_heat_soak %}
	
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,9000]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if not (beacon_adaptive_heat_soak or bed_heat_soak_time > 0) %}
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if printer.z_tilt is defined %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% endif %}
	{% if printer.quad_gantry_level is defined %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% endif %}
	
	
	_BEACON_CREATE_SCAN_COMPENSATION_MESH_CORE PROFILE="{profile}" DESIRED_SPACING={desired_spacing} CHAMBER_TEMP={chamber_temp} KEEP_TEMP_MESHES={keep_temp_meshes}
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	{% if automated %}
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon scan compensation mesh created!"
	
	
	{% if not automated %}
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED]
gcode = 
	
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED" MSG="beacon_scan_compensation_profile {beacon_scan_compensation_profile}, beacon_scan_compensation_enable {beacon_scan_compensation_enable}"
	
	{% if beacon_scan_compensation_enable %}
	BEACON_APPLY_SCAN_COMPENSATION PROFILE="{beacon_scan_compensation_profile}"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL]
gcode = 
	
	{% set beacon_contact_start_print_true_zero = params.BEACON_CONTACT_START_PRINT_TRUE_ZERO|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = params.beacon_contact_calibrate_model_on_true_zero|lower == 'true' %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and not printer.beacon.model %}
	{% set beacon_model_required_for_true_zero = beacon_contact_start_print_true_zero and not beacon_contact_calibrate_model_on_true_zero %}
	{% set beacon_model_required_for_homing =
	printer.fastconfig.settings.stepper_z.endstop_pin == 'probe:z_virtual_endstop'
	and (( printer.fastconfig.settings.beacon.home_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower != 'true')
	or ( printer.fastconfig.settings.beacon.default_probe_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower != 'true' )) %}
	{% if beacon_model_required_for_homing or beacon_model_required_for_true_zero %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("An active Beacon model is required. Have you performed initial Beacon calibration?") }
	{% endif %}
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION]
gcode = 
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set bed_temp_mismatch_is_error = true if printer["gcode_macro RatOS"].beacon_scan_compensation_bed_temp_mismatch_is_error|default(false)|lower == 'true' else false %}
	
	{% set bed_temp = params.BED_TEMP|default(0)|float %}
	{% if bed_temp == 0 %}
	{% set bed_temp = printer.heater_bed.temperature %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_PREFLIGHT_CHECK_BEACON" MSG="beacon_scan_compensation_profile={beacon_scan_compensation_profile}, beacon_scan_compensation_enable={beacon_scan_compensation_enable}, bed_temp={bed_temp}"
	
	{% if beacon_scan_compensation_enable %}
	_VALIDATE_COMPENSATION_MESH_PROFILE PROFILE="{beacon_scan_compensation_profile}" TITLE="Check Beacon scan compensation profile" SUBJECT="Configured compensation profile '{beacon_scan_compensation_profile}'" COMPARE_BED_TEMP={bed_temp} COMPARE_BED_TEMP_IS_ERROR={bed_temp_mismatch_is_error}
	{% endif %}

[gcode_macro _BEACON_MAYBE_SCAN_COMPENSATION]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set needs_scan_compensation = true if printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].needs_compensation|default(false)|lower == 'true' else false %}
	
	{% if needs_scan_compensation %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% endif %}

[gcode_macro _BEACON_HOME_AND_ABL]
gcode = 
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	{% if needs_rehoming %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}

[gcode_macro SAVE_Z_OFFSET]
description = Deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead, or in Mainsail use the SAVE button in the Z-OFFSET section.
gcode = 
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default('false')|lower == 'true' %}
	{% set msg = "SAVE_Z_OFFSET is deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead,_N_or in Mainsail use the SAVE button in the Z-OFFSET section."%}
	{% if not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% set msg = msg + "_N_You must then use the SAVE_CONFIG command to persist the change." %}
	{% endif %}
	CONSOLE_ECHO TYPE="error" MSG="{msg}"

[gcode_macro _BEACON_OFFSET_COMPARE]
gcode = 
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing..."
	
	
	BEACON_OFFSET_COMPARE SAMPLES_DROP=1 SAMPLES=3
	BEACON_QUERY

[fan]
pin = rpi:gpio4

[fan_generic part_fan_t0]
pin = PA8
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[fan_generic part_fan_t1]
pin = PE5
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[heater_fan toolhead_cooling_fan_t0]
heater = extruder
shutdown_speed = 1
pin = toolboard_t0:PB4

[heater_fan toolhead_cooling_fan_t1]
heater = extruder1
shutdown_speed = 1
pin = toolboard_t1:PB4

[controller_fan controller_fan]
pin = dinghy:PA4
tachometer_pin = dinghy:PC15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[z_offset_probe]
pin = ^PG10
z_offset = -7
y_offset = 0
x_offset = 37.5
speed = 10
samples = 3
sample_retract_dist = 5
lift_speed = 10.0
samples_result = median
samples_tolerance = 0.2
samples_tolerance_retries = 5

[neopixel vaoc_led]
pin = PB10
chain_count = 6
color_order = GRB

[heater_fan vaoc_fan]
pin = PD13
heater = heater_bed
fan_speed = 1.0
heater_temp = 50

[fan_generic filter]
pin = !PD14
enable_pin = PD15

[gcode_macro T0]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = True
variable_color = "7bff33"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = -32.6
variable_parking_position = -57.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=0 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[gcode_macro T1]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = False
variable_color = "0ea5e9"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = 532.6
variable_parking_position = 557.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=1 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[save_variables]
filename = /home/pi/printer_data/config/ratos-variables.cfg

[mcu dinghy]
serial = /dev/serial/by-id/usb-Klipper_stm32f072xb_Dragon_dinghy-if00

[temperature_sensor th0]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA0

[temperature_sensor th1]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA1

[temperature_sensor th2]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA2

[temperature_sensor th3]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA3

[controller_fan CTL2]
pin = dinghy:PB14
tachometer_pin = dinghy:PB15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[mcu plasma]
serial = /dev/serial/by-id/usb-Klipper_rp2040_Plasma-if00

[neopixel Chamber_Lights]
pin = plasma:gpio15
chain_count = 140
color_order = GRBW
initial_red = 0.0
initial_green = 0.0
initial_blue = 0.0
initial_white = 0.1

[beacon model default]
model_coef = 1.5287863993594841,
	1.9289099639750602,
	0.8838828622507556,
	0.25554883784260735,
	-0.015171504024913506,
	0.3044946127013882,
	0.15820427856566457,
	-0.25262403959326246,
	0.042488512846660914,
	0.16662470122520964
model_domain = 1.842634574664148e-07,1.9339206373083917e-07
model_range = 0.200000,5.000000
model_temp = 13.222247
model_offset = 0.00000
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 130, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 123, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 112, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 1766, in load_config
    return BedMesh(config)
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 107, in __init__
    self.splitter = MoveSplitter(config, self.gcode)
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 1259, in __init__
    self.split_delta_z = config.getfloat(
  File "/home/pi/klipper/klippy/configfile.py", line 70, in getfloat
    return self._get_wrapper(self.fileconfig.getfloat, option, default,
  File "/home/pi/klipper/klippy/configfile.py", line 49, in _get_wrapper
    raise error("Option '%s' in section '%s' must have minimum of %s"
configparser.Error: Option 'split_delta_z' in section 'bed_mesh' must have minimum of 0.01
webhooks client 3974436800: New connection
webhooks client 3974436800: Client info {'program': 'Moonraker', 'version': 'v0.9.3-0-g71f9e67'}
Attempting MCU 'mcu' reset
Unable to issue reset command on MCU 'rpi'
Attempting MCU 'toolboard_t0' reset
Attempting MCU 'toolboard_t1' reset
Attempting MCU 'dinghy' reset
Attempting MCU 'plasma' reset
webhooks client 3974436800: Disconnected
Restarting printer
Start printer at Tue Mar 17 04:06:02 2026 (1773720363.0 9967.3)
===== Config file =====
[mcu rpi]
serial = /tmp/klipper_host_mcu

[board_pins btt-octopus-pro-h723-11]
aliases = 
	
	
	
	x_step_pin=PF13,
	x_dir_pin=PF12,
	x_enable_pin=PF14,
	x_uart_pin=PC4,
	x_diag_pin=PG6,
	x_endstop_pin=PG6,
	
	
	
	dual_carriage_step_pin=PF9,
	dual_carriage_dir_pin=PF10,
	dual_carriage_enable_pin=PG2,
	dual_carriage_uart_pin=PF2,
	dual_carriage_diag_pin=PG12,
	dual_carriage_endstop_pin=PG12,
	
	
	
	y_step_pin=PG0,
	y_dir_pin=PG1,
	y_enable_pin=PF15,
	y_uart_pin=PD11,
	y_diag_pin=PG9,
	y_endstop_pin=PG9,
	
	
	
	y1_step_pin=PG4,
	y1_dir_pin=PC1,
	y1_enable_pin=PA2,
	y1_uart_pin=PC7,
	y1_diag_pin=PG11,
	y1_endstop_pin=PG11,
	
	
	
	z0_step_pin=PC13,
	z0_dir_pin=PF0,
	z0_enable_pin=PF1,
	z0_uart_pin=PE4,
	z0_diag_pin=PG13,
	
	
	
	z1_step_pin=PE2,
	z1_dir_pin=PE3,
	z1_enable_pin=PD4,
	z1_uart_pin=PE1,
	z1_diag_pin=PG14,
	
	
	
	z2_step_pin=PE6,
	z2_dir_pin=PA14,
	z2_enable_pin=PE0,
	z2_uart_pin=PD3,
	z2_diag_pin=PG15,
	
	e_step_pin=PF11,
	e_dir_pin=PG3,
	e_enable_pin=PG5,
	e_uart_pin=PC6,
	
	e_heater_pin=PA2,
	e_sensor_pin=PF4,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=PA7,
	stepper_spi_miso_pin=PA6,
	stepper_spi_sclk_pin=PA5,
	adxl345_cs_pin=PA15,
	bltouch_sensor_pin=PB7,
	bltouch_control_pin=PB6,
	probe_pin=PB7,
	fan_part_cooling_pin=PA8,
	fan_toolhead_cooling_pin=PE5,
	fan_controller_board_pin=PD12,
	heater_bed_heating_pin=PA1,
	heater_bed_sensor_pin=PF3,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PG15,
	filament_sensor_motion_pin=PG14,
	ratrig_vaoc_probe_pin=PG10,
	ratrig_vaoc_led_pin=PB0,
	ratrig_vaoc_fan_pin=PD13,
	chamber_lighting_pin=PB11,
	chamber_filter_4p_fan_pin=PD14,
	chamber_filter_4p_fan_enable_pin=PD15

[mcu]
serial = /dev/RatOS/btt-octopus-pro-h723-11

[temperature_sensor Octopus_Pro_H723_V1.1]
sensor_type = temperature_mcu

[adxl345 controlboard]
cs_pin = PA15
spi_software_mosi_pin = PB5
spi_software_miso_pin = PB4
spi_software_sclk_pin = PB3

[board_pins toolboard_t0]
mcu = toolboard_t0
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t0]
serial = /dev/RatOS/btt-ebb42-gen2-10-t0

[temperature_sensor EBB42_Gen2_v1.0_T0]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t0

[lis2dw toolboard_t0]
axes_map = x, z, y
cs_pin = toolboard_t0:PB1
spi_software_mosi_pin = toolboard_t0:PB11
spi_software_miso_pin = toolboard_t0:PB2
spi_software_sclk_pin = toolboard_t0:PB10

[board_pins toolboard_t1]
mcu = toolboard_t1
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t1]
serial = /dev/RatOS/btt-ebb42-gen2-10-t1

[temperature_sensor EBB42_Gen2_v1.0_T1]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t1

[lis2dw toolboard_t1]
axes_map = x, z, y
cs_pin = toolboard_t1:PB1
spi_software_mosi_pin = toolboard_t1:PB11
spi_software_miso_pin = toolboard_t1:PB2
spi_software_sclk_pin = toolboard_t1:PB10

[gcode_macro RatOS]
variable_homing = "endstops"
variable_z_probe = "static"
variable_sensorless_x_current = 0.6
variable_sensorless_y_current = 0.9
variable_safe_home_x = "middle"
variable_safe_home_y = "middle"
variable_driver_type_x = "tmc2209"
variable_driver_type_y = "tmc2209"
variable_stowable_probe_stop_on_error = False
variable_chamber_filter_enable = True
variable_chamber_filter_speed = 0.5
variable_chamber_filter_disable_speed = 1.0
variable_chamber_filter_enable_at = "after_print_start"
variable_chamber_filter_disable_period = 300
variable_chamber_filter_disable_bed_temp = 0
variable_chamber_heater_enable = True
variable_chamber_heater_bed_temp = 115
variable_chamber_heater_preheating_temp = 150
variable_chamber_heater_heating_temp_offset = 25
variable_chamber_heater_control_external_heater = False
variable_chamber_heater_air_circulation_enable = True
variable_chamber_heater_air_circulation_fan_speed = 0.35
variable_chamber_heater_air_circulation_y_pos = 0
variable_chamber_heater_air_circulation_z_pos = 100
variable_chamber_heater_extra_fan_speed = 1.0
variable_chamber_heater_filter_fan_speed = 1.0
variable_bed_heat_soak_time = 0
variable_hotend_heat_soak_time = 0
variable_led_status_action = 0.0,1.0,1.0
variable_led_status_success = 0.0,1.0,0.0
variable_led_status_error = 1.0,0.0,1.0
variable_led_status_on = 1.0,1.0,1.0
variable_led_status_off = 0.0,0.0,1.0
variable_led_status_standby = 0.1,0.1,0.1
variable_led_status_heating = 1.0,0.0,0.0
variable_led_status_cooling = 0.0,0.0,1.0
variable_calibrate_bed_mesh = True
variable_adaptive_mesh = True
variable_start_print_park_in = "center"
variable_start_print_park_z_height = 3
variable_end_print_park_in = "back"
variable_pause_print_park_in = "back"
variable_end_print_park_z_hop = 20
variable_nozzle_priming = "primeblob"
variable_nozzle_prime_start_x = "max"
variable_nozzle_prime_start_y = "min"
variable_nozzle_prime_direction = "auto"
variable_nozzle_prime_bridge_fan = 102
variable_probe_for_priming_result = None
variable_probe_for_priming_end_result = None
variable_probe_for_priming_result_t1 = None
variable_probe_for_priming_end_result_t1 = None
variable_probe_for_priming_disable_mesh_constraints = False
variable_adaptive_prime_offset_threshold = -1.0
variable_last_z_offset = None
variable_runout_park_in = "front"
variable_enable_unload_tip_forming = False
variable_filament_unload_length = 150
description = RatOS variable storage macro, will echo variables to the console when run.
variable_relative_extrusion = True
variable_force_absolute_position = False
variable_preheat_extruder = True
variable_preheat_extruder_temp = 150
variable_macro_travel_speed = 600
variable_macro_travel_accel = 8000
variable_macro_z_speed = 15
variable_bed_margin_x = [59.6, 59.6]
variable_bed_margin_y = [14.35, 33.65]
variable_printable_x_min = 0
variable_printable_x_max = 0
variable_printable_y_min = 0
variable_printable_y_max = 0
variable_end_print_motors_off = True
variable_status_color_ok = "00FF00"
variable_status_color_error = "FF0000"
variable_status_color_unknown = "FFFF00"
variable_end_print_retract_filament = 10
gcode = 
	ECHO_RATOS_VARS
variable_auto_center_subject = False
variable_toolchange_zhop = 2.0
variable_toolchange_zspeed = 25
variable_toolchange_sync_fans = False
variable_toolchange_combined_zhop = False
variable_toolchange_travel_speed = 600
variable_toolchange_travel_accel = 8000
variable_toolchange_extrusion = 2.0
variable_toolchange_retraction = 2.0
variable_toolchange_feedrate = 7200
variable_toolchange_prepurging_timer = 0
variable_toolchange_standby_temp = -1
variable_toolchange_purge = 25
variable_toolchange_first_purge = 50
variable_beacon_bed_mesh_scv = 25
variable_beacon_contact_z_homing = False
variable_beacon_contact_start_print_true_zero = True
variable_beacon_contact_start_print_true_zero_fuzzy_position = True
variable_beacon_contact_calibrate_model_on_true_zero = True
variable_beacon_contact_wipe_before_true_zero = True
variable_beacon_contact_wipe_before_true_zero_method = "probe_clean"
variable_beacon_contact_true_zero_temp = 170
variable_beacon_contact_prime_probing = True
variable_beacon_contact_expansion_compensation = True
variable_beacon_contact_bed_mesh = False
variable_beacon_contact_bed_mesh_samples = 2
variable_beacon_contact_z_tilt_adjust = False
variable_beacon_contact_z_tilt_adjust_samples = 2
variable_beacon_scan_compensation_enable = True
variable_beacon_scan_compensation_profile = "auto"
variable_beacon_scan_compensation_desired_spacing = 10
variable_beacon_scan_compensation_bed_temp_mismatch_is_error = False
variable_beacon_contact_poke_bottom_limit = -1
variable_beacon_scan_method_automatic = False
variable_beacon_adaptive_heat_soak = True
variable_beacon_adaptive_heat_soak_max_wait = 5400
variable_beacon_adaptive_heat_soak_extra_wait_after_completion = 0
variable_beacon_adaptive_heat_soak_layer_quality = 3
variable_beacon_adaptive_heat_soak_maximum_first_layer_duration = 1800
variable_beacon_contact_start_print_true_zero_fuzzy_radius = 20
variable_homing_x = "endstop"
variable_homing_y = "endstop"
variable_default_toolhead = 0
variable_adxl_chip = ["lis2dw toolboard_t0", "lis2dw toolboard_t1"]
variable_shaper_x_freq = [54.2, 53.2, 53.6, 54.4]
variable_shaper_y_freq = [40.8, 47.6, 38.6, 38]
variable_shaper_x_type = ["mzv", "mzv", "mzv", "mzv"]
variable_shaper_y_type = ["mzv", "mzv", "mzv", "mzv"]
variable_x_driver_types = ["tmc5160"]
variable_x_axes = ["x"]
variable_y_driver_types = ["tmc5160", "tmc5160"]
variable_y_axes = ["y", "y1"]
variable_z_driver_types = ["tmc2209", "tmc2209", "tmc2209"]
variable_z_axes = ["z", "z1", "z2"]
variable_home_y_first = True

[ratos_homing]
axes = xyz
z_hop = 15
z_hop_speed = 15
gcode = 
	
	_LED_ON
	
	
	{% set prev_stop_on_error = printer["gcode_macro RatOS"].stowable_probe_stop_on_error %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set target_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	_IDEX_SINGLE
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE=True
	
	
	M400
	
	G90
	
	
	{% set X = true if params.X is defined else false %}
	{% set Y = true if params.Y is defined else false %}
	{% set Z = true if params.Z is defined else false %}
	{% if printer["gcode_macro RatOS"].home_y_first|default(false)|lower == 'true' %}
	HOME_Y X={X} Y={Y} Z={Z}
	HOME_X X={X} Y={Y} Z={Z}
	{% else %}
	HOME_X X={X} Y={Y} Z={Z}
	HOME_Y X={X} Y={Y} Z={Z}
	{% endif %}
	HOME_Z X={X} Y={Y} Z={Z}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE={prev_stop_on_error}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[gcode_macro HOME_X]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_x = printer["gcode_macro RatOS"].homing_x|lower %}
	{% set homing_x = homing_x if homing_x else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_X" MSG="printable_x_max: {printable_x_max}, safe_home_x: {safe_home_x}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}"
	
	
	{% if X or not Y and not Z %}
	{% if homing_x == 'endstop' %}
	G28 X
	{% elif homing_x == 'sensorless' %}
	{% if printer["dual_carriage"] is defined %}
	{ action_emergency_stop("sensorless homing not supported on IDEX!") }
	{% endif %}
	HOME_X_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_x to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_x, homing)) }
	{% endif %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1} MODE=PRIMARY
	G1 X{parking_position} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	{% endif %}
	{% set x_homed = True %}
	G0 X{safe_home_x} F{speed}
	M400
	{% endif %}

[gcode_macro HOME_Y]
gcode = 
	
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_y = printer["gcode_macro RatOS"].homing_y|lower %}
	{% set homing_y = homing_y if homing_y else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Y" MSG="printable_y_max: {printable_y_max}, safe_home_y: {safe_home_y}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}"
	
	
	{% if Y or not X and not Z %}
	{% if homing_y == 'endstop' %}
	G28 Y
	{% elif homing_y == 'sensorless' %}
	HOME_Y_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_y to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_y, homing)) }
	{% endif %}
	{% set y_homed = True %}
	G0 Y{safe_home_y} F{speed}
	{% endif %}

[gcode_macro HOME_Z]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	
	
	{% set beacon_contact_z_homing = true if printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_z_home_position_fuzzing_radius = printer["gcode_macro RatOS"].beacon_z_home_position_fuzzing_radius|default(0)|float %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Z" MSG="x_homed: {x_homed}, y_homed: {y_homed}, z_probe: {z_probe}, beacon_contact_z_homing: {beacon_contact_z_homing}"
	
	
	{% if Z or not Y and not X %}
	RATOS_ECHO MSG="Homing Z"
	{% if x_homed == False or y_homed == False %}
	{ action_emergency_stop("X and Y must be homed before homing Z") }
	{% else %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_homing %}
	{% if beacon_contact_start_print_true_zero %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% else %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	{% else %}
	G28 Z
	{% endif %}
	_Z_HOP
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro HOME_X_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	
	G4 P300
	
	G28 X
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"

[gcode_macro HOME_Y_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	
	G4 P300
	
	G28 Y
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"

[gcode_macro _Z_HOP]
description = Move Z axis up by Z_HOP distance at Z_HOP_SPEED. In relative mode it will move Z axis up by Z_HOP distance. In absolute mode it will move Z axis to Z_HOP distance.
gcode = 
	{% set z_hop = printer.fastconfig.config.ratos_homing.z_hop|float %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	G0 Z{z_hop} F{z_hop_speed}

[gcode_macro __MOVE_TO_SAFE_Z_HOME_ECHO_DEBUG]
gcode = 
	DEBUG_ECHO PREFIX="_MOVE_TO_SAFE_Z_HOME" MSG="x: {params.X}, y: {params.Y}, z_hop: {params.Z_HOP}, fuzzy_radius: {params.FUZZY_RADIUS}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}, printable_x_max: {printer['gcode_macro RatOS'].printable_x_max}, printable_y_max: {printer['gcode_macro RatOS'].printable_y_max}"

[gcode_macro MAYBE_HOME]
description = Only home unhomed axis. Specify ABL=1 to also ensure that automatic bed levelling is applied (if configured).
variable_is_kinematic_position_overriden = False
gcode = 
	{% set abl = params.ABL|default('')|lower in ('true', 'yes', '1') %}
	{% if printer["gcode_macro MAYBE_HOME"].is_kinematic_position_overriden|lower == 'true' %}
	RATOS_ECHO MSG="SET_CENTER_KINEMATIC_POSITION has been abused. Homing all axes. Please refrain from using SET_CENTER_KINEMATIC_POSITION outside of debugging purposes."
	G28
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=False
	{% else %}
	{% set axes = '' %}
	{% set isHomed = true %}
	{% set axesToHome = '' %}
	{% if params.X is defined %}
	{% set axes = axes ~ 'X ' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% endif %}
	{% if params.Y is defined %}
	{% set axes = axes ~ 'Y ' %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% endif %}
	{% if params.Z is defined %}
	{% set axes = axes ~ 'Z ' %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if params.X is not defined and params.Y is not defined and params.Z is not defined %}
	{% set axes = '' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if isHomed is false %}
	RATOS_ECHO MSG="Homing {axesToHome}"
	G28 {axesToHome}
	{% else %}
	RATOS_ECHO MSG="All requested axes already homed. Skipping homing."
	{% endif %}
	{% endif %}
	{% if abl %}
	{% if printer.z_tilt is defined %}
	{% if not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Performing Z tilt adjustment..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Z tilt already applied. Skipping Z tilt adjustment."
	{% endif %}
	{% elif printer.quad_gantry_level is defined %}
	{% if not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Performing quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Quad gantry leveling already applied. Skipping quad gantry leveling."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="No automatic bed leveling method configured. Skipping bed leveling."
	{% endif %}
	{% endif %}

[gcode_macro PID_CALIBRATE_HOTEND]
description = Perform a PID calibration test for a given extruder heater.
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set temp = params.TEMP|default(220)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_HOTEND" MSG="TEMP={temp}"
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO MSG="PID calibration hotend heater T0 at {temp}°C..."
	PID_CALIBRATE HEATER=extruder TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	
	{% if toolhead==0 or toolhead==1 %}
	RATOS_ECHO MSG="PID calibration hotend heater T{toolhead} at {temp}°C..."
	PID_CALIBRATE HEATER=extruder{'' if toolhead==0 else toolhead} TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_BED]
description = Perform a PID calibration test for the bed heater.
gcode = 
	
	{% set temp = params.TEMP|default(80)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_BED" MSG="TEMP={temp}"
	RATOS_ECHO MSG="PID calibration bed heater at {temp}°C..."
	
	
	PID_CALIBRATE HEATER=heater_bed TARGET={temp}
	
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_CHAMBER_HEATER]
description = Perform a PID calibration test for the chamber heater.
gcode = 
	
	{% set temp = params.TEMP|default(150)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_CHAMBER_HEATER" MSG="TEMP={temp}"
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	RATOS_ECHO MSG="PID calibration chamber heater at {temp}°C..."
	PID_CALIBRATE HEATER=chamber_heater TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_heater" %}
	{% set link_text = "RatOS Chamber Heater" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber heater found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro INITIALIZE_PA_TUNING]
description = Start a pressure advance tuning tower.
gcode = 
	
	{% set start = params.START|default(0.0)|float %}
	{% set factor = params.FACTOR|default(0.001)|float %}
	
	
	{% set layer_number = printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|default(0)|int %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if is_printing_gcode and layer_number < 2 %}
	DEBUG_ECHO PREFIX="START_PA_TOWER" MSG="START: {start}, FACTOR: {factor}"
	RATOS_ECHO MSG="Starting pressure advance tuning tower..."
	TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START={start} FACTOR={factor}
	{% else %}
	RATOS_ECHO MSG="Pressure advance tuning tower requires you to be printing gcode and on layer 1 to start."
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro CHAMBER_FILTER_ON]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	_CHAMBER_FILTER_TURN_ON
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro CHAMBER_FILTER_OFF]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Deactivating chamber filter..."
	_CHAMBER_FILTER_TURN_OFF
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set chamber_filter_enable_at = printer["gcode_macro RatOS"].chamber_filter_enable_at|default('after_print_start')|lower %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_ON" MSG="at: {at}, chamber_filter_enable: {chamber_filter_enable}, chamber_filter_enable_at: {chamber_filter_enable_at}, chamber_filter_speed: {chamber_filter_speed}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	{% if chamber_filter_enable_at == at %}
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	
	
	_CHAMBER_FILTER_TURN_ON AT={at}
	
	
	{% if chamber_filter_enable_at == "print_end" %}
	_LED_CHAMBER_FILTER_ON
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_OFF]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF" MSG="chamber_filter_enable: {chamber_filter_enable}, filter_disable_period: {filter_disable_period}, filter_disable_bed_temp: {filter_disable_bed_temp}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	
	{% if filter_disable_period > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting {filter_disable_period} seconds before turning chamber filter off..."
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION={filter_disable_period}
	{% endif %}
	
	
	{% if filter_disable_bed_temp > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting for bed temp to cool down to {filter_disable_bed_temp}°C to turn filter off..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM=0 MAXIMUM={filter_disable_bed_temp}
	_CHAMBER_FILTER_TURN_OFF
	_LED_CHAMBER_FILTER_OFF
	{% endif %}
	
	{% endif %}

[delayed_gcode _CHAMBER_FILTER_OFF_TIMER]
gcode = 
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF_TIMER" MSG="executed"
	
	
	_CHAMBER_FILTER_TURN_OFF
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Chamber filter turned off!"
	
	
	_LED_CHAMBER_FILTER_OFF

[gcode_macro _CHAMBER_FILTER_TURN_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_speed|default(0)|float %}
	{% if at == "print_end" %}
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_disable_speed|default(0)|float %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION=0
	
	
	SET_FAN_SPEED FAN=filter SPEED={chamber_filter_speed}

[gcode_macro _CHAMBER_FILTER_TURN_OFF]
gcode = 
	
	SET_FAN_SPEED FAN=filter SPEED=0

[gcode_macro _CHAMBER_FILTER_SANITY_CHECK]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	{% if filter_disable_bed_temp > 0 and filter_disable_period > 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable, not both.")}
	{% endif %}
	
	{% if filter_disable_bed_temp == 0 and filter_disable_period == 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable.")}
	{% endif %}
	
	{% endif %}

[gcode_macro CHAMBER_HEATER_ON]
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(45)|int %}
	
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp} IS_FROM_START_PRINT=False

[gcode_macro CHAMBER_HEATER_OFF]
gcode = 
	_CHAMBER_HEATER_OFF

[gcode_macro _CHAMBER_HEATER_ON]
variable_chamber_temp = 0
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	{% set is_from_start_print = true if params.IS_FROM_START_PRINT|default(True)|lower == 'true' else false %}
	
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set chamber_heater_enable = true if printer["gcode_macro RatOS"].chamber_heater_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}
	{% set chamber_heater_preheating_temp = printer["gcode_macro RatOS"].chamber_heater_preheating_temp|default(150)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	{% set chamber_heater_control_external_heater = true if printer["gcode_macro RatOS"].chamber_heater_control_external_heater|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_enable = true if printer["gcode_macro RatOS"].chamber_heater_air_circulation_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_fan_speed = printer["gcode_macro RatOS"].chamber_heater_air_circulation_fan_speed|default(0.35)|float %}
	{% set chamber_heater_air_circulation_y_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_y_pos|default(0)|float %}
	{% set chamber_heater_air_circulation_z_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_z_pos|default(100)|float %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_HEATER_ON" MSG="chamber_heater_enable: {chamber_heater_enable}, chamber_heater_preheating_temp: {chamber_heater_preheating_temp}, chamber_heater_heating_temp_offset: {chamber_heater_heating_temp_offset}, bed_temp: {bed_temp}, chamber_temp: {chamber_temp}, start_chamber_temp: {start_chamber_temp}"
	
	
	{% if chamber_heater_enable and chamber_temp > 0 and chamber_heater_bed_temp > 0 %}
	
	
	_LED_HEATING
	
	
	RATOS_ECHO MSG="Preheating chamber to {(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}°C..."
	
	
	{% set chamber_temp_sensor = "extruder" %}
	{% if printer["dual_carriage"] is defined and default_toolhead == 1 %}
	{% set chamber_temp_sensor = "extruder1" %}
	{% endif %}
	{% if printer["temperature_sensor chamber"] is defined %}
	{% set chamber_temp_sensor = "temperature_sensor chamber" %}
	{% endif %}
	
	
	{% set current_chamber_temp = printer['%s' % chamber_temp_sensor].temperature|int %}
	
	
	{% set needs_heating = current_chamber_temp < (start_chamber_temp if start_chamber_temp > 0 else chamber_temp) %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_BEFORE_PREHEATING
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	{% if not is_from_start_print %}
	MAYBE_HOME
	{% endif %}
	G0 Z{chamber_heater_air_circulation_z_pos} F{z_speed}
	G0 Y{chamber_heater_air_circulation_y_pos} F{speed}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * chamber_heater_air_circulation_fan_speed)}
	{% endif %}
	{% else %}
	{% if is_from_start_print %}
	G0 Z{z} F{z_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE={chamber_temp}
	
	
	{% if needs_heating %}
	
	
	M140 S{chamber_heater_bed_temp}
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={chamber_heater_preheating_temp}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	
	{% endif %}
	
	
	{% if needs_heating %}
	_CHAMBER_HEATER_EXTRA_FAN_ON
	{% endif %}
	
	
	{% if needs_heating %}
	TEMPERATURE_WAIT SENSOR="{chamber_temp_sensor}" MINIMUM={(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% endif %}
	
	
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED=0
	_CHAMBER_FILTER_ON AT="before_print_start"
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	G28 Z
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_AFTER_PREHEATING
	{% endif %}
	
	
	{% if printer["temperature_sensor chamber"] is defined %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined and chamber_heater_control_external_heater %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	
	
	_LED_SUCCESS
	
	{% endif %}

[gcode_macro _CHAMBER_HEATER_OFF]
gcode = 
	RATOS_ECHO MSG="Deactivating chamber heater..."
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=0
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE=0
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	
	
	_CHAMBER_HEATER_EXTRA_FAN_OFF

[delayed_gcode _CHAMBER_HEATER_CONTROL]
initial_duration = 0.
gcode = 
	
	{% set chamber_temp = printer["gcode_macro _CHAMBER_HEATER_ON"].chamber_temp|default(0)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	
	
	{% set current_chamber_temp = printer['temperature_sensor chamber'].temperature|int %}
	
	
	{% if current_chamber_temp < chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	{% endif %}
	
	
	{% if current_chamber_temp >= chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_ON]
gcode = 
	
	{% set chamber_heater_extra_fan_speed = printer["gcode_macro RatOS"].chamber_heater_extra_fan_speed|default(0.0)|float %}
	
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	{% if chamber_heater_extra_fan_speed > 0 %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED={chamber_heater_extra_fan_speed}
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_OFF]
gcode = 
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED=0
	{% endif %}

[gcode_macro _USER_CHAMBER_HEATER_BEFORE_PREHEATING]
description = Will be executed before chamber preheating, only if heating is needed.
gcode = 

[gcode_macro _USER_CHAMBER_HEATER_AFTER_PREHEATING]
description = Will be executed after chamber preheating, only if heating was needed.
gcode = 

[gcode_macro RESET_HEATSOAK_SETTINGS]
description = Resets all heatsoak-related settings to startup defaults
gcode = 
	HEATSOAK_SETTINGS ACTION=reset

[gcode_macro USE_ADAPTIVE_HEATSOAK]
description = Temporarily enables adaptive bed heatsoaking (if a beacon probe is present), will reset to printer.cfg settings
	when Klipper is restarted. Optionally specify QUALITY (1-5) and maximum FIRST_LAYER_DURATION (in minutes).
	Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.QUALITY|default("1..5") %}
	{% set _ = params.FIRST_LAYER_DURATION|default("1..120 minutes") %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("Adaptive heatsoaking is only available when a beacon probe is configured.") }
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_quality = (settings.variable_beacon_adaptive_heat_soak_layer_quality if defsrc == 'startup' else current.beacon_adaptive_heat_soak_layer_quality)|default(3)|int %}
	{% set default_first_layer_duration_secs = (settings.variable_beacon_adaptive_heat_soak_maximum_first_layer_duration if defsrc == 'startup' else current.beacon_adaptive_heat_soak_maximum_first_layer_duration)|default(1800)|int %}
	{% if params2.QUALITY is defined %}
	{% set quality = params2.QUALITY|int %}
	{% if quality < 1 or quality > 5 %}
	{ action_raise_error("QUALITY must be between 1 (rough) and 5 (maximum). Use 3 (normal) if unsure.") }
	{% endif %}
	{% else %}
	{% set quality = default_quality %}
	{% endif %}
	{% if params2.FIRST_LAYER_DURATION is defined %}
	{% set first_layer_duration_mins = params2.FIRST_LAYER_DURATION|float %}
	{% if first_layer_duration_mins <= 0 %}
	{ action_raise_error("FIRST_LAYER_DURATION must be a positive number specifying the maximum first layer duration in minutes.") }
	{% endif %}
	{% if first_layer_duration_mins > 120 %}
	CONSOLE_ECHO MSG="FIRST_LAYER_DURATION will be limited to 120 minutes. Values larger than this will not have an effect on soak time."
	{% set first_layer_duration_mins = 120 %}
	{% endif %}
	{% set first_layer_duration_secs = (first_layer_duration_mins * 60.0)|int %}
	{% else %}
	{% set first_layer_duration_secs = default_first_layer_duration_secs %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	{% endif %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=True beacon_adaptive_heat_soak_layer_quality={quality} beacon_adaptive_heat_soak_maximum_first_layer_duration={first_layer_duration_secs}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."

[gcode_macro USE_FIXED_HEATSOAK]
description = Temporarily enables fixed bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
	Optionally specify DURATION (in minutes). Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.DURATION|default("0..720 minutes") %}
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_duration = (settings.variable_bed_heat_soak_time if defsrc == 'startup' else current.bed_heat_soak_time)|default(0)|int %}
	{% if params2.DURATION is defined %}
	{% set duration_mins = params2.DURATION|float %}
	{% if duration_mins < 0 %}
	{ action_raise_error("DURATION must be a non-negative number specifying the heatsoak duration in minutes.") }
	{% endif %}
	{% if duration_mins > 720 %}
	CONSOLE_ECHO MSG="DURATION will be limited to 720 minutes (12 hours). If you really need a larger value, adjust printer.cfg instead."
	{% set duration_mins = 720 %}
	{% endif %}
	{% set duration_secs = (duration_mins * 60.0)|int %}
	{% else %}
	{% set duration_secs = default_duration %}
	{% set duration_mins = duration_secs / 60.0 %}
	{% endif %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% if has_beacon %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=False bed_heat_soak_time={duration_secs}
	{% else %}
	HEATSOAK_SETTINGS QUIET=1 bed_heat_soak_time={duration_secs}
	{% endif %}
	{% if duration_mins < 1e-3 %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% else %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% endif %}

[gcode_macro USE_NO_HEATSOAK]
description = Temporarily disables bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
gcode = 
	USE_FIXED_HEATSOAK DURATION=0

[gcode_macro HEATSOAK_SETTINGS]
description = Shows or adjusts heatsoak settings
	- With no arguments: shows current heatsoak settings, specify VERBOSE=1 for detailed output
	- With arguments: sets the specified settings. Use the full setting name without the variable_ prefix, e.g. bed_heat_soak_time=300 or beacon_adaptive_heat_soak_layer_quality=4. See printer.cfg for available settings.
variable_default_source = "startup"
gcode = 
	
	{% set params2 = params %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% set quiet = params2.pop("QUIET", None)|default("0") in ("1", "true", "yes") %}
	{% set verbose = params2.pop("VERBOSE", None)|default("0") in ("1", "true", "yes") %}
	{% if has_beacon %}
	{% set vars = (
	"beacon_adaptive_heat_soak",
	"beacon_adaptive_heat_soak_max_wait",
	"beacon_adaptive_heat_soak_extra_wait_after_completion",
	"beacon_adaptive_heat_soak_layer_quality",
	"beacon_adaptive_heat_soak_maximum_first_layer_duration",
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% else %}
	{% set vars = (
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% endif %}
	{% set action = "show" if params|length == 0 else params2.ACTION %}
	{% if action is defined and params|length > 1 %}
	{ action_raise_error("ACTION cannot be specified with other parameters.") }
	{% elif action is not defined %}
	{% for k, v in params2.items() %}
	{% set k = k|lower %}
	{% if k in vars %}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Setting {k} to {v}"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={k} VALUE={v}
	{% else %}
	{ action_raise_error("Parameter '%s' is not recognised. Note that adaptive heatsoaking settings can only be set when a beacon probe is configured." % k) }
	{% endif %}
	{% endfor %}
	{% elif action == "reset" %}
	_RESET_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	CONSOLE_ECHO MSG="Heatsoak settings have been reset to their original values."
	{% elif action == "show" %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% set is_adaptive = False if not has_beacon else current.beacon_adaptive_heat_soak|default("")|lower == "true" %}
	{% if is_adaptive %}
	{% set quality = current.beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set first_layer_duration_secs = current.beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."
	{% elif current.bed_heat_soak_time|default(0)|int > 0 %}
	{% set duration_mins = (current.bed_heat_soak_time|int / 60.0) %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% else %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% endif %}
	{% if verbose %}
	CONSOLE_ECHO MSG="Detailed settings:"
	_SHOW_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	{% endif %}
	{% else %}
	{ action_raise_error("Action '%s' is not recognised" % action) }
	{% endif %}

[gcode_macro _LED_START_PRINTING]
gcode = 
	_LED_ACTION

[gcode_macro _LED_START_PRINTING_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_PRINTING]
gcode = 
	_LED_ON TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_PAUSE]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_ON]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_OFF]
gcode = 
	_LED_STANDBY

[gcode_macro _LED_LOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_LOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_RUNOUT]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_CLOG]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_UNLOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_UNLOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_DEACTIVATE_TOOLHEAD]
gcode = 
	_LED_OFF TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_STANDBY]
gcode = 
	_LED_STANDBY TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_WAKEUP]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_MOTORS_OFF]
gcode = 
	_LED_STANDBY
	_LED_VAOC_OFF

[gcode_macro _LED_INPUT_SHAPER_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_INPUT_SHAPER_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_BEACON_CALIBRATION_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_VAOC_ON]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=1.0 GREEN=1.0 BLUE=1.0
	{% endif %}

[gcode_macro _LED_VAOC_OFF]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=0.0 GREEN=0.0 BLUE=0.0
	{% endif %}

[gcode_macro _LED_ACTION]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_action %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SUCCESS]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_success %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_HEATING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_heating %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_COOLING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_cooling %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ERROR]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_error %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ON]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_on %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_OFF]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_off %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_STANDBY]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_standby %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}
	
	{% if toolhead >= 0 %}
	{% if printer['neopixel nozzle_led_t%s' % toolhead] is defined  %}
	SET_LED LED={'nozzle_led_t%s' % toolhead} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% else %}
	{% if printer['neopixel nozzle_led_t0'] is defined  %}
	SET_LED LED={'nozzle_led_t0'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% if printer['neopixel nozzle_led_t1'] is defined %}
	SET_LED LED={'nozzle_led_t1'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% endif %}
	
	_USER_LED_SET { rawparams }

[gcode_macro _USER_LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}

[gcode_macro LOAD_FILAMENT]
description = Loads new filament. Note: be careful with PETG, make sure you inspect the tip of your filament before loading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% if filament_name == '' or filament_type == '' %}
	{% set filament_name = 'unknown' %}
	{% set filament_type = 'unknown' %}
	{% endif %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_LOAD_FILAMENT TEMP={temp} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_LOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_LOAD_FILAMENT]
description = Load filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_LOAD_FILAMENT" MSG="TEMP={temp}"
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=load_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	_LOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	
	
	RESTORE_GCODE_STATE NAME=load_state
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament load routine complete, please check that the filament was loaded correctly."

[gcode_macro _IDEX_LOAD_FILAMENT]
description = Load filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament into T{toolhead}..."
	
	DEBUG_ECHO PREFIX="_IDEX_LOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	_LOAD_FILAMENT TOOLHEAD={toolhead} TEMP={temp} AUTOMATED={automated}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="Filament load routine for T{toolhead} complete, please check that the filament was loaded correctly."

[gcode_macro _LOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default(false)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE TOOLHEAD={toolhead}
	_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into hotend.."
	G92 E0
	G0 E{extruder_gear_to_cooling_position_distance} F{extruder_load_speed}
	G92 E0
	M400
	RATOS_ECHO MSG="Filament loaded into hotend."

[gcode_macro _LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set load_speed = printer["gcode_macro T%s" % toolhead].filament_load_speed|float * 60 %}
	{% set filament_loading_nozzle_offset = printer["gcode_macro T%s" % toolhead].filament_loading_nozzle_offset|float %}
	{% set cooling_position_to_nozzle_distance = printer["gcode_macro T%s" % toolhead].cooling_position_to_nozzle_distance|float %}
	{% set purge_after_load = printer["gcode_macro T%s" % toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into nozzle... Please wait!"
	G92 E0
	
	G0 E{cooling_position_to_nozzle_distance + filament_loading_nozzle_offset} F{load_speed}
	G92 E0
	G4 P1000
	_PURGE_FILAMENT	TOOLHEAD={toolhead} E={purge_after_load}
	RATOS_ECHO MSG="Filament loaded into nozzle!"

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"
	
	
	{% set filament_grabbing_length = printer["gcode_macro T%s" % toolhead].filament_grabbing_length|float %}
	{% set filament_grabbing_speed = printer["gcode_macro T%s" % toolhead].filament_grabbing_speed|float %}
	{% set resume_after_insert = true if printer["gcode_macro T%s" % toolhead].resume_after_insert|default(true)|lower == 'true' else false %}
	{% set enable_insert_detection = true if printer["gcode_macro T%s" % toolhead].enable_insert_detection|default(true)|lower == 'true' else false %}
	
	
	{% set current_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	
	{% if enable_insert_detection %}
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="toolhead: {toolhead}, filament_grabbing_length: {filament_grabbing_length}, filament_grabbing_speed: {filament_grabbing_speed}, current_idex_mode: {current_idex_mode}"
	
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	RATOS_ECHO MSG="Filament inserted into T{toolhead}, loading..."
	
	
	FORCE_MOVE STEPPER={'extruder%s' % ('' if toolhead == 0 else toolhead)} DISTANCE={filament_grabbing_length} VELOCITY={filament_grabbing_speed}
	M400
	
	
	{% if printer.pause_resume.is_paused %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% if resume_after_insert %}
	RESUME
	{% endif %}
	{% else %}
	{% if not printer.virtual_sdcard.is_active %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"

[gcode_macro _PURGE_BEFORE_UNLOAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set purge_before_unload = printer["gcode_macro T%s" % toolhead].purge_before_unload|float %}
	
	DEBUG_ECHO PREFIX="_PURGE_BEFORE_UNLOAD" MSG="TOOLHEAD: {toolhead}"
	
	
	{% if purge_before_unload > 0 %}
	G92 E0
	G0 E{purge_before_unload} F300
	G92 E0
	M400
	{% endif %}

[gcode_macro _PURGE_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set e = params.E|int %}
	{% set r = params.R|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_PURGE_FILAMENT" MSG="TOOLHEAD: {toolhead}, E: {e}"
	
	
	{% if e > 0 %}
	
	
	G92 E0
	G0 E{e} F300
	G92 E0
	M400
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={0.4 if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={0.4 if toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * 0.4)}
	{% endif %}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if r > 0 %}
	G92 E0
	G0 E-{r} F300
	G92 E0
	M400
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro _MOVE_TO_LOADING_POSITION]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_MOVE_TO_LOADING_POSITION" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	
	G1 X{loading_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _CLEANING_MOVE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_CLEANING_MOVE" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].parking_position is defined and printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set parking_position = printer["gcode_macro T%s" % toolhead].parking_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	{% set cleaning_position = loading_position %}
	{% if loading_position == parking_position %}
	{% if loading_position > 0 %}
	{% set cleaning_position = loading_position - 30 %}
	{% else %}
	{% set cleaning_position = loading_position + 30 %}
	{% endif %}
	{% endif %}
	
	
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _BED_MESH_SANITY_CHECK]
gcode = 
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is defined %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_start_print_true_zero_fuzzy_position %}
	CONSOLE_ECHO TYPE="error" TITLE="Defined zero reference not compatible with fuzzy true zero" MSG="Using fuzzy start print true zero position is not compatible with a defined zero_reference_position value in the [bed_mesh] section in printer.cfg._N_Please remove the zero_reference_position value from the [bed_mesh] section, or disable fuzzy true zero position in printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_start_print_true_zero_fuzzy_position: False"
	_STOP_AND_RAISE_ERROR MSG="Defined zero reference not compatible with fuzzy true zero"
	{% elif zero_ref_pos[0]|float|round != safe_home_x|float|round or zero_ref_pos[1]|float|round != safe_home_y|float|round %}
	CONSOLE_ECHO TYPE="error" TITLE="Zero reference position does not match safe home position" MSG="Please update your bed mesh zero reference position in printer.cfg, like so:_N__N_[bed_mesh]_N_zero_reference_position: {safe_home_x|float|round},{safe_home_y|float|round}_N_"
	_STOP_AND_RAISE_ERROR MSG="Zero reference position does not match safe home position"
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_bed_mesh %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact bed mesh is enabled" MSG="Beacon contact bed mesh is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_bed_mesh: False"
	{% endif %}
	
	{% if beacon_scan_method_automatic %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon 'automatic' scan method is enabled" MSG="Beacon 'automatic' scan method is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_scan_method_automatic: False"
	{% endif %}
	
	{% if beacon_contact_z_tilt_adjust %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact z-tilt adjust is enabled" MSG="Beacon contact z-tilt adjust is enabled. This is not recommended for normal use and may result in inaccurate z-tilt adjustment._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_z_tilt_adjust: False"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH]
gcode = 
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE=None
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE=None
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION {rawparams}
	{% endif %}

[gcode_macro _START_PRINT_BED_MESH]
variable_actual_true_zero_position_x = None
variable_actual_true_zero_position_y = None
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set X=[params.X0|default(-1)|float, params.X1|default(-1)|float] %}
	{% set Y=[params.Y0|default(-1)|float, params.Y1|default(-1)|float] %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_BED_MESH" MSG="idex_mode: {idex_mode}, X: {X}, Y: {Y}"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is not defined %}
	{% set zero_ref_pos = [safe_home_x if actual_true_zero_position_x is none else actual_true_zero_position_x, safe_home_y if actual_true_zero_position_y is none else actual_true_zero_position_y] %}
	{% endif %}
	
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	
	
	
	
	{% set X=[0, printable_x_max] %}
	{% endif %}
	
	
	{% set beacon_bed_mesh_scv = printer["gcode_macro RatOS"].beacon_bed_mesh_scv|default(25)|int %}
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% if printer.fastconfig.settings.beacon is defined and not beacon_contact_bed_mesh %}
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={beacon_bed_mesh_scv}
	{% endif %}
	
	
	{% set default_profile = printer["gcode_macro RatOS"].bed_mesh_profile|default('ratos') %}
	{% if printer["gcode_macro RatOS"].calibrate_bed_mesh|lower == 'true' %}
	BED_MESH_CLEAR
	{% if printer["gcode_macro RatOS"].adaptive_mesh|lower == 'true' %}
	CALIBRATE_ADAPTIVE_MESH PROFILE="{default_profile}" X0={X[0]} X1={X[1]} Y0={Y[0]} Y1={Y[1]} T={params.T|int} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={idex_mode} ZERO_REF_POS_X={zero_ref_pos[0]} ZERO_REF_POS_Y={zero_ref_pos[1]}
	{% else %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	BED_MESH_PROFILE LOAD="{default_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	
	{% elif printer["gcode_macro RatOS"].bed_mesh_profile is defined %}
	BED_MESH_CLEAR
	BED_MESH_PROFILE LOAD="{printer["gcode_macro RatOS"].bed_mesh_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"

[gcode_macro CALIBRATE_ADAPTIVE_MESH]
gcode = 
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set default_profile = params.PROFILE %}
	
	
	{% set x0 = params.X0|default(-1)|float %}
	{% set y0 = params.Y0|default(-1)|float %}
	{% set x1 = params.X1|default(-1)|float %}
	{% set y1 = params.Y1|default(-1)|float %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Received coordinates X0={x0|round(1)} Y0={y0|round(1)} X1={x1|round(1)} Y1={y1|round(1)}"
	
	{% if x0 >= x1 or y0 >= y1 %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Invalid coordinates received. Please check your slicer settings. Falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	
	
	{% if params.ZERO_REF_POS_X is defined and params.ZERO_REF_POS_Y is defined %}
	{% set zero_ref_pos_x = params.ZERO_REF_POS_X|float %}
	{% set zero_ref_pos_y = params.ZERO_REF_POS_Y|float %}
	{% if zero_ref_pos_x < x0 or zero_ref_pos_x > x1 or zero_ref_pos_y < y0 or zero_ref_pos_y > y1 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Zero reference position X={zero_ref_pos_x|round(1)} Y={zero_ref_pos_y|round(1)} is outside the mesh region, expanding mesh region to include it."
	{% set x0 = [x0, zero_ref_pos_x]|min %}
	{% set y0 = [y0, zero_ref_pos_y]|min %}
	{% set x1 = [x1, zero_ref_pos_x]|max %}
	{% set y1 = [y1, zero_ref_pos_y]|max %}
	{% endif %}
	{% endif %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float %}
	
	
	{% set mesh_x0 = [[x0, max_x]|min, min_x]|max %}
	{% set mesh_y0 = [[y0, max_y]|min, min_y]|max %}
	{% set mesh_x1 = [[x1, max_x]|min, min_x]|max %}
	{% set mesh_y1 = [[y1, max_y]|min, min_y]|max %}
	
	{% if mesh_x0 == min_x and mesh_y0 == min_y and mesh_x1 == max_x and mesh_y1 == max_y %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Print is using the full bed, falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	
	{% set probe_count_x = mesh_config.probe_count.split(",")[0]|int %}
	{% if mesh_config.probe_count.split(",")|length == 2 %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[1]|int %}
	{% else %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[0]|int %}
	{% endif %}
	
	
	{% set probe_x_step = (max_x - min_x) / probe_count_x %}
	{% set probe_y_step = (max_y - min_y) / probe_count_y %}
	
	
	{% set mesh_count_x = ([(mesh_x1 - mesh_x0) / probe_x_step, 3]|max)|int %}
	{% set mesh_count_y = ([(mesh_y1 - mesh_y0) / probe_y_step, 3]|max)|int %}
	{% set min_mesh_count = [mesh_count_x, mesh_count_y]|min %}
	{% set max_mesh_count = [mesh_count_x, mesh_count_y]|max %}
	
	
	{% set algorithm = mesh_config.algorithm %}
	{% if algorithm|lower == 'lagrange' and max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="cannot exceed a probe_count of 6 when using lagrange interpolation. Falling back to bicubic interpolation."
	{% set algorithm = 'bicubic' %}
	{% endif %}
	{% if algorithm|lower == 'bicubic' and min_mesh_count < 4 %}
	{% if max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="invalid probe_count option when using bicubic interpolation. Combination of 3 points on one axis with more than 6 on another is not permitted. Forcing minimum mesh count to be 4."
	{% set min_mesh_count = 4 %}
	{% else %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="bicubic interpolation with a probe_count of less than 4 points detected. Forcing lagrange interpolation."
	{% set algorithm = 'lagrange' %}
	{% endif %}
	{% endif %}
	
	{% set mesh_count_x = ([min_mesh_count, mesh_count_x]|max)|int %}
	{% set mesh_count_x = ([max_mesh_count, mesh_count_x]|min)|int %}
	{% set mesh_count_y = ([min_mesh_count, mesh_count_y]|max)|int %}
	{% set mesh_count_y = ([max_mesh_count, mesh_count_y]|min)|int %}
	
	{% set should_prime = printer["gcode_macro RatOS"].nozzle_priming == 'primeblob' %}
	{% if printer["dual_carriage"] is not defined %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% else %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 != 0 and probe_first %}
	{% set probe_first = false %}
	{% elif printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 == 0 and not probe_first %}
	{% set probe_first = true %}
	{% endif %}
	
	
	{% if should_prime and probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="mesh coordinates X0={mesh_x0|round(1)} Y0={mesh_y0|round(1)} X1={mesh_x1|round(1)} Y1={mesh_y1|round(1)}"
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y} RELATIVE_REFERENCE_INDEX=-1
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	
	
	{% if should_prime and not probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro M84]
rename_existing = M84.1
gcode = 
	
	M84.1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_OFFSET X=0 Y=0
	
	
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro _VAOC"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False
	{% endif %}
	
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	SET_SKEW CLEAR=1
	
	
	_LED_MOTORS_OFF

[gcode_macro M104]
rename_existing = M104.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M104" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set temperature_offset_t0 = printer["gcode_macro T0"].temperature_offset|default(0)|int %}
	{% set temperature_offset_t1 = printer["gcode_macro T1"].temperature_offset|default(0)|int %}
	{% set s0 = [s + temperature_offset_t0, 0]|max %}
	{% set s1 = [s + temperature_offset_t1, 0]|max %}
	{% if temperature_offset_t0 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t0}°C added to toolhead T0."
	{% endif %}
	{% if temperature_offset_t1 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t1}°C added to toolhead T1."
	{% endif %}
	{% else %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	M104.1 S{s0} T0
	M104.1 S{s1} T1
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% else %}
	M104.1 S{s} T{t}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M109]
rename_existing = M109.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M109" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M109" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	M109.1 S{s} T{t}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro SET_HEATER_TEMPERATURE]
rename_existing = SET_HEATER_TEMPERATURE_BASE
gcode = 
	
	{% set heater = params.HEATER|default("") %}
	{% set target = params.TARGET|default(0)|int %}
	
	DEBUG_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="heater: {heater}, target: {target}"
	
	{% set t = -1 %}
	{% if heater|lower == "extruder" or heater|lower == "extruder1" %}
	
	{% set t = 0 if heater|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and target > 0 %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set target = [target + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE_BASE HEATER="{heater}" TARGET={target}
	
	{% if t != -1 and printer.fastconfig.settings.beacon is defined %}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro TEMPERATURE_WAIT]
rename_existing = TEMPERATURE_WAIT_BASE
gcode = 
	
	{% set sensor = params.SENSOR|default("") %}
	{% set minimum = params.MINIMUM|default(-1)|int %}
	{% set maximum = params.MAXIMUM|default(-1)|int %}
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="sensor: {sensor}, minimum: {minimum}, maximum: {maximum}"
	
	{% set t = -1 %}
	{% if sensor|lower == "extruder" or sensor|lower == "extruder1" %}
	
	{% set t = 0 if sensor|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and (minimum > 0 or maximum > 0) %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% if minimum > -1 %}
	{% set minimum = [minimum + temperature_offset, 0]|max %}
	{% endif %}
	{% if maximum > -1 %}
	{% set maximum = [maximum + temperature_offset, 0]|max %}
	{% endif %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set id = "sensor " ~ sensor if t == -1 else "toolhead T" ~ t %}
	
	
	{% if minimum > -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum} MAXIMUM={maximum}
	{% elif minimum > -1 and maximum == -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum}
	{% elif minimum == -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MAXIMUM={maximum}
	{% else %}
	
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="neither MINIMUM or MAXIMUM args were specified, call TEMPERATURE_WAIT_BASE is expected to fail"
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}"
	{% endif %}
	
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature for {id} reached."

[gcode_macro SDCARD_PRINT_FILE]
rename_existing = SDCARD_PRINT_FILE_BASE
gcode = 
	{% if printer["ratos"] is defined %}
	PROCESS_GCODE_FILE { rawparams }
	{% else %}
	SDCARD_PRINT_FILE_BASE { rawparams }
	{% endif %}

[gcode_macro SKEW_PROFILE]
rename_existing = SKEW_PROFILE_BASE
variable_loaded_profile = ""
gcode = 
	{% if params.LOAD is defined %}
	{% if printer.fastconfig.settings["skew_correction %s" % params.LOAD] is defined %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='"{params.LOAD}"'
	{% endif %}
	{% endif %}
	
	SKEW_PROFILE_BASE { rawparams }

[gcode_macro SET_SKEW]
rename_existing = SET_SKEW_BASE
gcode = 
	{% if params.CLEAR is defined %}
	{% if params.CLEAR|default(0)|int == 1 %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='""'
	{% endif %}
	{% endif %}
	
	SET_SKEW_BASE { rawparams }

[gcode_macro SET_VELOCITY_LIMIT]
rename_existing = SET_VELOCITY_LIMIT_BASE
gcode = 
	{% if params.ACCEL_TO_DECEL is defined %}
	
	{% if params.ACCEL is defined %}
	{% set accel = params.ACCEL|float %}
	{% else %}
	{% set accel = printer.toolhead.max_accel|float %}
	{% endif %}
	
	{% if params.VELOCITY is defined %}
	{% set velocity = params.VELOCITY|float %}
	{% else %}
	{% set velocity = printer.toolhead.max_velocity|float %}
	{% endif %}
	
	{% if params.SQUARE_CORNER_VELOCITY is defined %}
	{% set scv = params.SQUARE_CORNER_VELOCITY|float %}
	{% else %}
	{% set scv = printer.toolhead.square_corner_velocity|float %}
	{% endif %}
	
	{% set mcr = params.ACCEL_TO_DECEL|float / accel %}
	
	DEBUG_ECHO PREFIX="SET_VELOCITY_LIMIT" MSG="ACCEL={accel}, VELOCITY={velocity}, SQUARE_CORNER_VELOCITY={scv}, MINIMUM_CRUISE_RATIO={mcr}"
	
	SET_VELOCITY_LIMIT_BASE ACCEL={accel} VELOCITY={velocity} SQUARE_CORNER_VELOCITY={scv} MINIMUM_CRUISE_RATIO={1-mcr}
	
	{% else %}
	
	SET_VELOCITY_LIMIT_BASE { rawparams }
	
	{% endif %}

[gcode_macro BED_MESH_CALIBRATE]
rename_existing = _BED_MESH_CALIBRATE_BASE
variable_abl_and_home_z_if_required = True
gcode = 
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	{% if abl_and_home_z_if_required %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% endif %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set beacon_default_probe_method = printer.fastconfig.settings.beacon.default_probe_method|default('proximity') %}
	{% set probe_method = params.PROBE_METHOD|default(beacon_default_probe_method)|lower %}
	{% if probe_method == 'proximity' %}
	_CHECK_ACTIVE_BEACON_MODEL_TEMP TITLE="Bed mesh calibration warning"
	{% endif %}
	{% endif %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_BED_MESH_CALIBRATE_BASE {rawparams}
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	_APPLY_RATOS_BED_MESH_PARAMETERS {rawparams}
	{% endif %}

[gcode_macro SET_GCODE_OFFSET]
rename_existing = SET_GCODE_OFFSET_BASE
gcode = 
	DEBUG_ECHO PREFIX="SET_GCODE_OFFSET" MSG="{rawparams|replace('"', '')|replace("'", '')}"
	{% set z_before = printer.gcode_move.homing_origin.z|float %}
	SET_GCODE_OFFSET_BASE {rawparams}
	_AFTER_SET_GCODE_OFFSET Z_BEFORE={z_before}

[gcode_macro _AFTER_SET_GCODE_OFFSET]
gcode = 
	{% set z_before = params.Z_BEFORE|float %}
	{% set z_after = printer.gcode_move.homing_origin.z|float %}
	{% if z_before != z_after %}
	_ALERT_NON_ZERO_Z_OFFSET FORCE=1
	{% endif %}

[gcode_macro _START_PRINT_PARK]
gcode = 
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_x = printer["gcode_macro RatOS"].start_print_park_x %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% if printer["gcode_macro RatOS"].start_print_park_x is defined and printer["gcode_macro RatOS"].start_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="start_print_park_x is ignored for IDEX printers"
	{% endif %}
	PARK_TOOLHEAD
	G90
	{% endif %}
	
	
	_PARK LOCATION={start_print_park_in} X={start_print_park_x}
	G0 Z{z} F{z_speed}

[gcode_macro _END_PRINT_PARK]
gcode = 
	{% if printer["dual_carriage"] is defined %}
	
	{% if printer["gcode_macro RatOS"].end_print_park_x is defined and printer["gcode_macro RatOS"].end_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="end_print_park_x is ignored for IDEX printers"
	{% endif %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	PARK_TOOLHEAD
	G90
	{% endif %}
	_PARK LOCATION={printer["gcode_macro RatOS"].end_print_park_in} X={printer["gcode_macro RatOS"].end_print_park_x}

[gcode_macro _PARK]
gcode = 
	
	{% set x = params.X %}
	{% set location = params.LOCATION|default('back')|lower %}
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	{% set nozzle_priming = printer["gcode_macro RatOS"].nozzle_priming|lower %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="park"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% if x != '' %}
	{% if x|float >= printer.toolhead.axis_minimum.x + 5 and x|float <= printable_x_max - 5 %}
	{% set park_x = x|float %}
	{% else %}
	{action_respond_info('The requested X co-ordinate is outside the defined axis bounds - using defaults')}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	{% else %}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	
	
	{% set park_y = printable_y_max - 15 %}
	{% if location == 'front' %}
	{% set park_y = printer.toolhead.axis_minimum.y + 5 %}
	{% elif location == 'center' %}
	{% set park_y = printable_y_max / 2 %}
	{% elif location == 'primeblob' and printer["dual_carriage"] is defined %}
	
	{% set park_y = printable_y_max - 15 %}
	{% endif %}
	
	
	{% if location == 'primeblob' and printer["dual_carriage"] is not defined %}
	{% if (nozzle_priming == 'primeblob' or nozzle_priming == 'primeline') %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set park_x = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set park_x = printable_x_max - 5 %}
	{% else %}
	{% set park_x = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set park_y = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set park_y = printable_y_max - 5 %}
	{% else %}
	{% set park_y = nozzle_prime_start_y|float %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	G0 X{park_x} Y{park_y} F{speed}
	{% else %}
	
	G0 Y{park_y} F{speed}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="park"

[gcode_macro SAVE_PROBE_RESULT]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	{% set last_z_offset = 9999.9 %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if beacon_contact_prime_probing %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	{% else %}
	{% set last_z_offset = printer.beacon.last_sample.dist - current_z %}
	{% endif %}
	{% elif printer.fastconfig.settings.bltouch is defined  %}
	{% set config_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% elif printer.fastconfig.settings.probe is defined  %}
	{% set config_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% endif %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Saving offset adjustment of {last_z_offset} in {params.VARIABLE|default('last_z_offset')}"
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={params.VARIABLE|default('last_z_offset')} VALUE={last_z_offset}

[gcode_macro PROBE_FOR_PRIMING]
gcode = 
	
	{% set probe_for_priming_disable_mesh_constraints = true if printer["gcode_macro RatOS"].probe_for_priming_disable_mesh_constraints|default(false)|lower == 'true' else false %}
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower != 'false' %}
	SAVE_GCODE_STATE NAME=probe_for_priming_state
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the prime location.."
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set t = params.TOOLHEAD|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% if idex_mode == '' %}
	
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% if t == 0 %}
	{% set x_start = 5 %}
	{% else %}
	{% set x_start = printable_x_max - 5 %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% endif %}
	{% endif %}
	{% set z = printer.fastconfig.settings.bed_mesh.horizontal_move_z|float %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% if printer.fastconfig.settings.bltouch is defined %}
	{% set x_offset = printer.fastconfig.settings.bltouch.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.bltouch.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% elif printer.fastconfig.settings.probe is defined %}
	{% set x_offset = printer.fastconfig.settings.probe.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.probe.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% elif printer.fastconfig.settings.beacon is defined %}
	{% set x_offset = printer.fastconfig.settings.beacon.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.beacon.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.beacon.trigger_distance|float %}
	{% else %}
	{ action_raise_error("No probe, beacon or bltouch section found. Adaptive priming only works with a [probe], [beacon] or [bltouch] section defined.") }
	{% endif %}
	
	{% if z < z_offset %}
	{ action_raise_error("Horizontal move Z ({z}) is below your probe's Z offset ({z_offset}). Please adjust your horizontal_move_z setting in [bed_mesh] to be above {z}.") }
	{% endif %}
	
	{% if not probe_for_priming_disable_mesh_constraints %}
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float - x_offset %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float - y_offset %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float - x_offset %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float - y_offset %}
	
	
	{% set x_start = [[x_start, max_x]|min, min_x]|max %}
	{% set y_start = [[y_start, max_y]|min, min_y]|max %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the start of the prime location at {x_start}, {y_start}"
	
	G90
	
	M83
	
	G0 Z{z} F{z_speed}
	
	G1 X{x_start} Y{y_start} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result
	{% endif %}
	
	{% if idex_mode == '' %}
	
	{% set x_end = x_start %}
	{% set y_end = y_start + 45 %}
	{% else %}
	
	{% if t==1 %}
	{% set x_end = x_start - 45 %}
	{% else %}
	{% set x_end = x_start + 45 %}
	{% endif %}
	{% set y_end = y_start %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the end of the prime location at {x_end}, {y_end}"
	G1 X{x_end} Y{y_end} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result
	{% endif %}
	
	RESTORE_GCODE_STATE NAME=probe_for_priming_state
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	{% endif %}

[gcode_macro RESET_PRIME_PROBE_STATE]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result VALUE=None
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result_t1 VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result_t1 VALUE=None
	{% endif %}

[gcode_macro PROBE_CURRENT_POSITION]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	SAVE_GCODE_STATE NAME=probe_current_position_state
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	ASSERT_PROBE_DEPLOYED
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_prime_probing %}
	PROBE PROBE_METHOD=contact SAMPLES=1
	{% else %}
	PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	BEACON_QUERY
	{% else %}
	
	RESTORE_GCODE_STATE NAME=probe_current_position_state MOVE=1 MOVE_SPEED={printer["gcode_macro RatOS"].macro_z_speed|float}
	{% endif %}

[gcode_macro PRIME_BLOB]
description = Prints a primeblob, used internally, if configured, as part of the START_PRINT macro.
variable_x_offset = 5
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="prime_blob"
	SET_MACRO_TRAVEL_SETTINGS
	
	RATOS_ECHO PREFIX="Priming" MSG="Priming nozzle with prime blob.."
	
	
	{% set current_toolhead = 0 %}
	
	
	{% set target_idex_mode = '' %}
	{% set extruder = 'extruder' %}
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE is defined %}
	{% set target_idex_mode = params.IDEX_MODE|default('')|lower %}
	{% else %}
	{ action_raise_error("IDEX_MODE parameter not found for PRIME_BLOB macro. This is likely a bug.") }
	{% endif %}
	RATOS_ECHO PREFIX="Priming" MSG="Priming in IDEX {target_idex_mode} mode.."
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set current_toolhead = 1 if current_idex_mode=='primary' else 0 %}
	{% set extruder = 'extruder1' if current_toolhead == 1 else 'extruder' %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	SAVE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set fan_speed = printer["gcode_macro RatOS"].nozzle_prime_bridge_fan|float %}
	{% set nozzle_diameter = printer.fastconfig.settings[extruder].nozzle_diameter|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set has_start_offset_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) != 9999.9 %}
	{% if printer["dual_carriage"] is defined %}
	{% set has_start_offset_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) != 9999.9 %}
	{% endif %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_z_height = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set nozzle_prime_direction = printer["gcode_macro RatOS"].nozzle_prime_direction|lower %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% if target_idex_mode == '' %}
	
	{% set x_factor = 0 %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% set y_factor = -1 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% if nozzle_prime_start_y|float < printable_y_max / 2 %}
	{% set y_factor = 1 %}
	{% else %}
	{% set y_factor = -1 %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_direction == 'forwards' %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_direction == 'backwards' %}
	{% set y_factor = -1 %}
	{% endif %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% else %}
	{% set z = start_print_park_z_height %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% set y_factor = 0 %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set x_start = center_x / 2 + 5 %}
	{% set x_factor = 1 %}
	{% else %}
	
	
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% if current_toolhead == 0 %}
	{% set x_start = 55 %}
	{% set x_factor = -1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 55 %}
	{% set x_factor = 1 %}
	{% endif %}
	{% else %}
	{% if current_toolhead == 0 %}
	{% set x_start = 5 %}
	{% set x_factor = 1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 5 %}
	{% set x_factor = -1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_x_max - 5 %}
	{% endif %}
	{% set z = 10 %}
	{% endif %}
	
	{% set start_z_offset = 0 %}
	{% set end_z_offset = 0 %}
	{% if has_start_offset_t0 %}
	{% set start_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) %}
	{% set end_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_end_result|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t0) ) }
	{% endif %}
	{% if end_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t0) )  }
	{% endif %}
	{% set start_z_offset = start_z_probe_result_t0 %}
	{% set end_z_offset = end_z_probe_result_t0 %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	{% if current_toolhead == 1 or both_toolheads or target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	{% if has_start_offset_t1 %}
	{% set start_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) %}
	{% set end_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_end_result_t1|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t1) ) }
	{% endif %}
	{% if end_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t1) ) }
	{% endif %}
	{% set start_z_offset = [start_z_offset, start_z_probe_result_t1]|max %}
	{% set end_z_offset = [end_z_offset, start_z_probe_result_t1]|max %}
	{% endif %}
	{% endif %}
	{% if target_idex_mode != 'copy' and target_idex_mode != 'mirror' %}
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% set original_start_z_offset = start_z_offset %}
	{% set original_end_z_offset = end_z_offset %}
	{% set start_z_offset = original_end_z_offset %}
	{% set end_z_offset = original_start_z_offset %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	DEBUG_ECHO PREFIX="PRIME_BLOB" MSG="x_start: {x_start}, y_start: {y_start}, x_factor: {x_factor}, y_factor: {y_factor}, z: {z}, start_z_offset: {start_z_offset}, end_z_offset: {end_z_offset}"
	
	
	G90
	
	M83
	RATOS_ECHO PREFIX="Priming" MSG="Lifting Z to {z}.."
	
	G0 Z{z} F{z_speed}
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% if start_print_park_in != 'primeblob' %}
	G1 X{x_start} F{speed}
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% endif %}
	{% else %}
	
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% if target_idex_mode=="copy" or target_idex_mode=="mirror" %}
	RATOS_ECHO PREFIX="Priming" MSG="Mirroring move to {x_start}, {y_start} along the edge of the print area.."
	
	_IDEX_MIRROR PRIMING=1
	{% else %}
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% endif %}
	G1 X{x_start} F{speed}
	{% endif %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Starting prime blob.."
	
	G1 Z{0.5 + start_z_offset} F{z_speed}
	
	G1 Y{y_start} F{speed}
	
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	
	M106 S{fan_speed}
	
	G1 Z5 F100 E5
	G92 E0
	RATOS_ECHO PREFIX="Priming" MSG="Bridging with {((fan_speed/255) * 100)|int}% fan speed.."
	
	G1 F3000 X{x_start + (15 * x_factor)} Y{y_start + (15 * y_factor)} E{1 / ((0.4 / nozzle_diameter) ** 2)}
	
	
	
	G1 F3000 X{x_start + (20 * x_factor)} Y{y_start + (20 * y_factor)} Z{3.8 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (34 * x_factor)} Y{y_start + (34 * y_factor)} Z{2.6 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (38 * x_factor)} Y{y_start + (38 * y_factor)} Z{1.4 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (42 * x_factor)} Y{y_start + (42 * y_factor)} Z{0.2 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	
	M106 S0
	
	G1 F3000 X{x_start + (46 * x_factor)} Y{y_start + (46 * y_factor)} Z{0.2 + end_z_offset} E0.6
	
	G1 F{speed} X{x_start + (50 * x_factor)} Y{y_start + (50 * y_factor)}
	
	
	{% if target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if target_idex_mode == "copy" %}
	{% if first_y >= 0 %}
	_IDEX_COPY DANCE=0 Y={first_y}
	{% else %}
	_IDEX_COPY DANCE=0 Y={params.Y1}
	{% endif %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	RESTORE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="prime_blob"
	
	
	G92 E0

[gcode_macro UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set temp = params.TEMP|default(220)|int %}
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_UNLOAD_FILAMENT TEMP={temp} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_UNLOAD_FILAMENT]
description = Unload filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_UNLOAD_FILAMENT" MSG="TEMP: {temp}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=unload_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	G4 P3000
	
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD=0 NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=unload_state
	
	
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament unloading completed"

[gcode_macro _IDEX_UNLOAD_FILAMENT]
description = Unload filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading T{toolhead} filament..."
	
	DEBUG_ECHO PREFIX="_IDEX_UNLOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} AUTOMATED={automated}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="T{toolhead} filament unloading completed"

[gcode_macro _UNLOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LEGACY_UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
gcode = 
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set unload_speed = 5 * 60 %}
	{% set unload_length = printer["gcode_macro RatOS"].filament_unload_length|float %}
	M117 Unloading filament...
	
	G0 E10 F300
	
	G0 E-5 F3600
	
	G4 P3000
	
	G0 E5 F6000
	
	G0 E-15 F6000
	
	G0 E-{unload_length} F{unload_speed}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}
	M117 Filament unloaded!
	RESPOND MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	RATOS_ECHO MSG="Unloading filament from nozzle to cooling zone... Please wait!"
	
	_PURGE_BEFORE_UNLOAD TOOLHEAD={toolhead}
	
	{% if printer["gcode_macro _UNLOAD_WITHOUT_TIP_FORMING"] is defined %}
	
	_UNLOAD_WITHOUT_TIP_FORMING TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	_UNLOAD_WITH_TIP_FORMING NAME='{filament_name}' TYPE='{filament_type}'
	{% endif %}
	
	G4 P3000

[gcode_macro _UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	{% set tooolhead_sensor_to_extruder_gear_distance = printer["gcode_macro T%s" % toolhead].tooolhead_sensor_to_extruder_gear_distance|float %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER" MSG="TOOLHEAD: {toolhead}"
	
	
	G0 E-{extruder_gear_to_cooling_position_distance + tooolhead_sensor_to_extruder_gear_distance + 50} F{extruder_load_speed}
	
	RATOS_ECHO MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_WITH_TIP_FORMING]
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	{% if filament_name != '' and filament_type != '' %}
	_UNLOAD_KNOWN_FILAMENT NAME={filament_name} TYPE={filament_type}
	{% else %}
	_UNLOAD_UNKNOWN_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _UNLOAD_KNOWN_FILAMENT]
description = User overrideable tip forming macro if slicer filament profiles are known
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	RATOS_ECHO PREFIX="FILAMENT TYPE" MSG='{filament_type}'
	RATOS_ECHO PREFIX="FILAMENT PROFILE" MSG='{filament_name}'
	
	
	{% if filament_name == "Prusament PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% elif filament_name == "Nobufil PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% else %}
	
	RATOS_ECHO PREFIX="_UNLOAD_KNOWN_FILAMENT" MSG="Filament profile not found!"
	_UNLOAD_UNKNOWN_FILAMENT
	{% endif %}

[gcode_macro _UNLOAD_UNKNOWN_FILAMENT]
description = User overrideable standard tip forming macro
gcode = 
	
	DEBUG_ECHO PREFIX="_UNLOAD_UNKNOWN_FILAMENT" MSG="Using standard tip forming macro!"
	
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10

[gcode_macro _TIP_FORMING]
gcode = 
	
	{% set cooling_moves = params.COOLING_MOVES|default(4)|int %}
	{% set cooling_move_length = params.COOLING_MOVE_LENGTH|default(10)|float %}
	{% set start_cooling_speed = params.START_COOLING_SPEED|default(10)|float * 60 %}
	{% set end_cooling_speed = params.END_COOLING_SPEED|default(50)|float * 60 %}
	{% if cooling_moves == 0 %}
	{% set cooling_move_length = 0 %}
	{% endif %}
	
	
	{% set dip = true if params.DIP|default(false)|lower == "true" else false %}
	{% set dip_length = params.DIP_LENGTH|default(22)|float %}
	{% set dip_speed = params.DIP_SPEED|default(30)|float * 60 %}
	{% set dip_retract_speed = params.DIP_RETRACT_SPEED|default(70)|float * 60 %}
	
	
	{% set retract_length = params.RETRACT_LENGTH|default(18)|float %}
	{% set start_retract_speed = params.START_RETRACT_SPEED|default(120)|float * 60 %}
	{% set end_retract_speed = params.END_RETRACT_SPEED|default(20)|float * 60 %}
	
	DEBUG_ECHO PREFIX="_TIP_FORMING" MSG="cooling_moves: {cooling_moves}, cooling_move_length: {cooling_move_length}, start_cooling_speed: {start_cooling_speed}, end_cooling_speed: {end_cooling_speed}, dip: {dip}, dip_length: {dip_length}, dip_speed: {dip_speed}, dip_retract_speed: {dip_retract_speed}, retract_length: {retract_length}, start_retract_speed: {start_retract_speed}, end_retract_speed: {end_retract_speed}"
	
	M220 S100
	
	
	G92 E0
	{% set retract = retract_length + cooling_move_length / 2 - 15 %}
	G1 E-15 F{start_retract_speed}
	G1 E-{0.7 * retract} F{1.0 * end_retract_speed}
	G1 E-{0.2 * retract} F{0.5 * end_retract_speed}
	G1 E-{0.1 * retract} F{0.3 * end_retract_speed}
	
	
	G92 E0
	{% if cooling_moves > 0 %}
	{% set i = (end_cooling_speed - start_cooling_speed) / (2 * cooling_moves - 1) %}
	{% for m in range(cooling_moves) %}
	G1 E{cooling_move_length} F{(start_cooling_speed + i * m * 2)}
	G1 E-{cooling_move_length} F{(start_cooling_speed + i * (m * 2 + 1))}
	{% endfor %}
	{% endif %}
	
	
	G92 E0
	{% if dip %}
	G1 E{dip_length} F{dip_speed}
	G4 P100
	G1 E-{dip_length} F{dip_retract_speed}
	{% endif %}
	
	G92 E0
	M400

[delayed_gcode __ON_FILAMENT_SENSOR_BUTTON_PRESSED_STARTUP_GUARD]
initial_duration = 2.
gcode = 
	SET_GCODE_VARIABLE MACRO=_ON_FILAMENT_SENSOR_BUTTON_PRESSED VARIABLE=startup_complete VALUE=True

[gcode_macro _ON_FILAMENT_SENSOR_BUTTON_PRESSED]
variable_startup_complete = False
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set toolhead_sensor_button_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_sensor_button_only_when_sensor_enabled|default(false)|lower == 'true' %}
	
	
	{% if not startup_complete and sensor_enabled %}
	{action_emergency_stop("RatOS: The T%s filament sensor button was triggered immediately on printer startup. This is likely a false trigger. Please check your filament sensor wiring and configuration!" % (toolhead,))}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_SENSOR_BUTTON_PRESSED" MSG="TOOLHEAD: {toolhead}, SENSOR_ENABLED: {sensor_enabled}, TOOLHEAD_SENSOR_BUTTON_ONLY_WHEN_SENSOR_ENABLED: {toolhead_sensor_button_only_when_sensor_enabled}"
	
	{% if not printer.virtual_sdcard.is_active and (sensor_enabled or not toolhead_sensor_button_only_when_sensor_enabled) %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	{% set toolhead_detect_clog_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_detect_clog_only_when_sensor_enabled|default(true)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}, ENABLE_CLOG_DETECTION: {enable_clog_detection}, TOOLHEAD_DETECT_CLOG_ONLY_WHEN_SENSOR_ENABLED: {toolhead_detect_clog_only_when_sensor_enabled}, SENSOR_ENABLED: {sensor_enabled}"
	
	{% if enable_clog_detection and (sensor_enabled or not toolhead_detect_clog_only_when_sensor_enabled) %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_clog_detection %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_FILAMENT_END]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set clogged = true if params.CLOGGED|default(false)|lower == 'true' else false %}
	
	
	{% set unload_after_runout = printer["gcode_macro T%s" % toolhead].unload_after_runout|float %}
	
	
	{% if clogged %}
	_LED_FILAMENT_CLOG TOOLHEAD={toolhead}
	{% else %}
	_LED_FILAMENT_RUNOUT TOOLHEAD={toolhead}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_END" MSG="TOOLHEAD: {toolhead}"
	
	{% if printer.virtual_sdcard.is_active %}
	{% if not printer.pause_resume.is_paused %}
	PAUSE RUNOUT=True
	{% endif %}
	{% if not clogged and unload_after_runout %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	{% if not clogged and printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true'%}
	_JOIN_SPOOL TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M600]
description = Executes a color change by pausing the printer an unloading the filament.
gcode = 
	PAUSE
	UNLOAD_FILAMENT AUTOMATED=True
	RATOS_ECHO MSG="Please load new filament and resume"

[gcode_macro COLD_PULL]
description = Automated hotend cold pull.
gcode = 
	
	{% set extrusion_temp = params.EXTRUSION_TEMP|default(220)|int %}
	{% set cold_pull_temp = params.COLD_PULL_TEMP|default(80)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	
	{% if printer["dual_carriage"] is not defined %}
	{% set toolhead = 0 %}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead != 0 and toolhead != 1 %}
	{action_raise_error("Please select toolhead! 0 = left, 1 = right toolhead")}
	{% endif %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	RATOS_ECHO MSG="Starting cold pull on T{toolhead}..."
	{% else %}
	RATOS_ECHO MSG="Starting cold pull..."
	{% endif %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	SAVE_GCODE_STATE NAME=cold_pull_state
	
	
	{% if printer["dual_carriage"] is defined and "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	RATOS_ECHO MSG="Heating T{toolhead} to {extrusion_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={extrusion_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={extrusion_temp} MAXIMUM={extrusion_temp + 2}
	
	
	G4 P3000
	
	
	RATOS_ECHO MSG="extruding..."
	G92 E0
	G1 E30 F300
	G92 E0
	
	
	RATOS_ECHO MSG="Cooling T{toolhead} to {cold_pull_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={cold_pull_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={cold_pull_temp} MAXIMUM={cold_pull_temp + 2}
	
	
	G4 P10000
	
	
	RATOS_ECHO MSG="cold pull..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-40 VELOCITY=5 ACCEL=100
	
	
	RATOS_ECHO MSG="eject filament..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-200 VELOCITY=20 ACCEL=500
	
	
	RATOS_ECHO MSG="cooling down extruder..."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	RESTORE_GCODE_STATE NAME=cold_pull_state
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	
	CONSOLE_ECHO TITLE="Cold pull complete" MSG="Please remove the filament from the PTFE tube and cut the end off. Do NOT try to load it again." TYPE="warning"

[gcode_macro _USER_START_PRINT_BEFORE_HOMING]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_BED]
gcode = 

[gcode_macro _USER_START_PRINT_BED_MESH]
gcode = 

[gcode_macro _USER_START_PRINT_PARK]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 

[gcode_macro _USER_START_PRINT_HEAT_CHAMBER]
description = Uses the extruder sensor to wait for chamber temp. Override the _START_PRINT_HEAT_CHAMBER macro to implement heated chamber handling.
gcode = 
	
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}

[gcode_macro _USER_END_PRINT_BEFORE_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_AFTER_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_PARK]
gcode = 

[gcode_macro _USER_END_PRINT_FINISHED]
description = User hook for when the print is finished after gcode state has been restored.
gcode = 

[gcode_macro _USER_START_PRINT]
gcode = 

[gcode_macro _USER_END_START_PRINT]
gcode = 

[gcode_macro _USER_START_FEATURE]
gcode = 

[gcode_macro _USER_END_FEATURE]
gcode = 

[gcode_macro _USER_BEFORE_IDLE_TIMEOUT]
gcode = 

[gcode_macro _USER_AFTER_IDLE_TIMEOUT]
gcode = 

[gcode_macro ECHO_T_VARS]
description = Echo Toolhead variables to the console.
gcode = 
	{% set t = params.T|default(0) %}
	RATOS_ECHO MSG="T{t} Variables"
	{% for var, value in printer["gcode_macro T%s" % t].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ECHO_RATOS_VARS]
description = Echo RatOS variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro RatOS"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ENSURE_CRITICAL_RATOS_INIT]
variable_completed = False
gcode = 
	{% if not completed %}
	CALCULATE_PRINTABLE_AREA
	SET_GCODE_VARIABLE MACRO=ENSURE_CRITICAL_RATOS_INIT VARIABLE=completed VALUE=True
	{% endif %}

[delayed_gcode RATOS_INIT]
initial_duration = 0.1
gcode = 
	{action_respond_info("Initializing RatOS...")}
	ENSURE_CRITICAL_RATOS_INIT
	_LED_STANDBY
	INITIAL_FRONTEND_UPDATE
	_CHAMBER_FILTER_SANITY_CHECK
	{% if printer.fastconfig.settings.beacon is defined %}
	
	_BED_MESH_SANITY_CHECK
	{% endif %}
	{% set svv = printer.save_variables.variables %}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=0 C={svv.nozzle_expansion_coefficient_t0|default(0.06)|float}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=1 C={svv.nozzle_expansion_coefficient_t1|default(0.06)|float}
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=idex_applied_offset

[delayed_gcode RATOS_LOGO]
initial_duration = 2
gcode = 
	
	
	
	
	
	ENSURE_CRITICAL_RATOS_INIT
	HELLO_RATOS
	_ALERT_NON_ZERO_Z_OFFSET

[gcode_macro _ALERT_NON_ZERO_Z_OFFSET]
gcode = 
	{% set force = params.FORCE|default(0)|int == 1 %}
	{% set user_offset = printer.named_offsets.user_probe_z_offset.z|float %}
	{% set gcode_offset = printer.gcode_move.homing_origin.z|float %}
	{% set combined_offset = user_offset + gcode_offset %}
	
	{% if force or user_offset != 0 or gcode_offset != 0 %}
	{% set title = "User-adjusted Z-offset of %.3f mm is active" % combined_offset %}
	{% set msg = "" %}
	{% set nl = "" %}
	{% if user_offset != 0 %}
	{% set msg = msg + "beacon true zero user Z-offset: %.3f mm (to clear, use Z_OFFSET_APPLY_PROBE CLEAR=1)" % user_offset %}
	{% set nl = "_N_" %}
	{% endif %}
	{% if gcode_offset != 0 %}
	{% set msg = msg + nl + "G-code Z-offset: %.3f mm" % gcode_offset %}
	{% endif %}
	CONSOLE_ECHO TITLE="{title}" TYPE="info" MSG="{msg}"
	{% endif %}

[gcode_macro _INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE]
gcode = 
	{% set variable = params.VARIABLE|string %}
	{% set svv = printer.save_variables.variables %}
	{% set nlu_msg = "no longer used, please remove" %}
	{% if svv[variable] is defined %}
	{% set v = svv[variable]|string|replace('"', '')|replace("'", "") %}
	{% if not nlu_msg in v %}
	SAVE_VARIABLE VARIABLE={variable} VALUE='"{nlu_msg} (was {v})"'
	{% endif %}
	CONSOLE_ECHO TITLE="Deprecated ratos-variables.cfg variable" TYPE="warning" MSG="The variable {variable} is no longer used, please remove it from your ratos-variables.cfg file."
	{% endif %}

[gcode_macro _NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK]
gcode = 
	
	
	
	
	
	
	
	{% set t = params.T|int %}
	{% set c = params.C|float %}
	{% set normal_low = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_low|default(0.05)|float %}
	{% set normal_high = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_high|default(0.10)|float %}
	
	{% if c < 0 %}
	
	{action_emergency_stop("Invalid nozzle_expansion_coefficient_t%s value in ratos-variables.cfg: %.3f. It must be non-negative." % (t, c))}
	{% endif %}
	{% if c >= normal_high %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite high. Please verify that this is correct."
	{% endif %}
	{% if c <= normal_low %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite low. Please verify that this is correct."
	{% endif %}

[gcode_macro INITIAL_FRONTEND_UPDATE]
gcode = 
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_error = printer["gcode_macro RatOS"].status_color_error|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_unknown}"'
	{% endif %}
	
	
	{% set t0_sensor = "undefined" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	{% set t0_sensor = "detected" %}
	{% else %}
	{% set t0_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t0_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	{% set t1_sensor = "undefined" %}
	{% if printer["dual_carriage"] is defined and printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	{% set t1_sensor = "detected" %}
	{% else %}
	{% set t1_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t1_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	{% if svv.t0_filament is defined and printer["gcode_macro T0"] is defined %}
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	{% if t0_sensor != "empty" %}
	{% set t0_filament_type = svv.t0_filament[0]|default('')|string %}
	{% set t0_filament_name = svv.t0_filament[1]|default('')|string %}
	{% set t0_filament_temp = svv.t0_filament[2]|default(0)|float %}
	{% if t0_filament_name != '' and t0_filament_type != '' and t0_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{t0_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{t0_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={t0_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}
	{% if svv.t1_filament is defined and printer["gcode_macro T1"] is defined %}
	{% if printer["gcode_macro T1"].filament_name is defined and printer["gcode_macro T1"].filament_type is defined and printer["gcode_macro T1"].filament_temp is defined %}
	{% if t1_sensor != "empty" %}
	{% set t1_filament_type = svv.t1_filament[0]|default('')|string %}
	{% set t1_filament_name = svv.t1_filament[1]|default('')|string %}
	{% set t1_filament_temp = svv.t1_filament[2]|default(0)|float %}
	{% if t1_filament_name != '' and t1_filament_type != '' and t1_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='"{t1_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='"{t1_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE={t1_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t1_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro CALCULATE_PRINTABLE_AREA]
variable_calculated = False
gcode = 
	{% if not calculated %}
	{% set bed_margin_x = printer["gcode_macro RatOS"].bed_margin_x %}
	{% set bed_margin_y = printer["gcode_macro RatOS"].bed_margin_y %}
	
	
	
	{% set tool = 0 if printer["gcode_macro T0"] is not defined or printer["gcode_macro T0"].active else 1 %}
	{% set max_x = printer.toolhead.axis_maximum.x if printer["dual_carriage"] is defined and tool == 0 else printer.toolhead.axis_maximum.x - bed_margin_x[1] %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	
	
	{% set max_x = printer.toolhead.axis_maximum.x %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="printer.toolhead.axis_maximum.x {printer.toolhead.axis_maximum.x}"
	
	{% set max_y = printer.toolhead.axis_maximum.y - bed_margin_y[1]%}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_x_max VALUE={max_x}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_y_max VALUE={max_y}
	SET_GCODE_VARIABLE MACRO=CALCULATE_PRINTABLE_AREA VARIABLE=calculated VALUE=True
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	RATOS_LOG PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	{% endif %}

[gcode_macro CACHE_TOOLHEAD_SETTINGS]
variable_cache = {"global": {"accel": 1000, "ratio": 0.5, "speed": 50, "scv": 5}}
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set dummy = cache.__setitem__(key, {"accel": printer.toolhead.max_accel, "ratio": printer.toolhead.minimum_cruise_ratio, "speed": printer.toolhead.max_velocity, "scv": printer.toolhead.square_corner_velocity}) %}
	SET_GCODE_VARIABLE MACRO=CACHE_TOOLHEAD_SETTINGS VARIABLE=cache VALUE="{cache | pprint | replace("\n", "") | replace("\"", "\\\"")}"
	DEBUG_ECHO PREFIX="CACHE_TOOLHEAD_SETTINGS" MSG="Toolhead settings cached for {key}. {printer.toolhead.max_accel} accel, {printer.toolhead.minimum_cruise_ratio} ratio, {printer.toolhead.max_velocity} velocity, {printer.toolhead.square_corner_velocity} scv."

[gcode_macro RESTORE_TOOLHEAD_SETTINGS]
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set values = printer["gcode_macro CACHE_TOOLHEAD_SETTINGS"].cache.__getitem__(key) %}
	{% if values is not defined or values == 'None' %}
	{ action_raise_error("RESTORE_TOOLHEAD_SETTINGS: Toolhead settings not cached for key '" ~ key ~ "'.") }
	{% endif %}
	SET_VELOCITY_LIMIT ACCEL={values.accel} MINIMUM_CRUISE_RATIO={values.ratio} VELOCITY={values.speed} SQUARE_CORNER_VELOCITY={values.scv}
	DEBUG_ECHO PREFIX="RESTORE_TOOLHEAD_SETTINGS" MSG="Toolhead settings restored. {values.accel} accel, {values.ratio} ratio, {values.speed} velocity, {values.scv} scv."

[gcode_macro SET_MACRO_TRAVEL_SETTINGS]
gcode = 
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float %}
	{% set accel = printer["gcode_macro RatOS"].macro_travel_accel %}
	SET_VELOCITY_LIMIT ACCEL={accel} MINIMUM_CRUISE_RATIO=0.5 VELOCITY={speed} SQUARE_CORNER_VELOCITY={5}
	DEBUG_ECHO PREFIX="SET_MACRO_TRAVEL_SETTINGS" MSG="Macro travel settings set. {accel} accel, {speed} velocity"

[gcode_macro SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% if printer["dual_carriage"] is not defined %}
	
	SET_KINEMATIC_POSITION X={printable_x_max / 2} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	{% else %}
	
	IDEX_SET_CENTER_KINEMATIC_POSITION
	{% endif %}

[gcode_macro IDEX_SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x - (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x + (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY

[gcode_macro VERIFY_HYBRID_INVERTED]
gcode = 
	
	{% set inverted = False %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy is defined and printer.fastconfig.settings.ratos_hybrid_corexy.inverted is defined %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy.inverted|lower == 'true' %}
	{% set inverted = True %}
	{% endif %}
	{% endif %}
	{% if inverted == False %}
	{ action_emergency_stop("ratos_hybrid_corexy NOT INVERTED! Inverted hybrid core-xy bugfix not detected.") }
	{% endif %}

[gcode_macro RATOS_ECHO]
gcode = 
	{% set prefix = "RatOS" %}
	{% set debug = params.DEBUG|default(0)|int %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " | " ~ params.PREFIX %}
	{% endif %}
	{% set prefix = prefix ~ ":" %}
	{% set msg = "" %}
	{% if params.MSG is defined %}
	{% set msg = params.MSG %}
	{% else %}
	{% set msg = "No msg parameter provided (this is a bug or unintended use)." %}
	{% endif %}
	{% if not debug %}
	
	M117 {prefix} {msg}
	{% endif %}
	RATOS_LOG PREFIX="{prefix}" MSG="{msg}"
	{% if not debug %}
	RESPOND PREFIX="{prefix}" MSG="{msg}"
	{% else %}
	CONSOLE_ECHO TITLE="{prefix}" TYPE="debug" MSG="{msg}"
	{% endif %}

[gcode_macro ENABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=True
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=prefix_filter VALUE="'{params.FILTER|default('')|lower}'"
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging enabled."

[gcode_macro DISABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=False
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging disabled."

[gcode_macro DEBUG_ECHO]
variable_enabled = False
variable_prefix_filter = ''
gcode = 
	{% set prefix = "DEBUG" %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " - " ~ params.PREFIX %}
	{% endif %}
	{% if enabled and (prefix_filter|lower == '' or prefix_filter|lower in params.PREFIX|lower) %}
	RATOS_ECHO PREFIX="{prefix}" MSG="{params.MSG}" DEBUG=1
	{% endif %}

[gcode_macro START_FEATURE]
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="Start {params.FEATURE} feature gcode"
	{% set scv = printer.toolhead.square_corner_velocity|int|default(5) %}
	{% set accel = printer.toolhead.max_accel|int|default(10000) %}
	{% set ratio = printer.toolhead.minimum_cruise_ratio|float|default(0.5) %}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="scv" VALUE={scv}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="accel" VALUE={accel}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="ratio" VALUE={ratio}
	_USER_START_FEATURE FEATURE="{params.FEATURE}"

[gcode_macro END_FEATURE]
variable_scv = 5
variable_accel = 10000
variable_ratio = 0.5
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="End {params.FEATURE} feature gcode"
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={scv} ACCEL={accel} MINIMUM_CRUISE_RATIO={ratio}
	_USER_END_FEATURE FEATURE="{params.FEATURE}" SCV={scv} ACCEL={accel} RATIO={ratio}

[gcode_macro _ON_LAYER_CHANGE]
variable_layer_number = 0
description = INTERNAL USE ONLY. Call it from the slicers after layer change custom gcode
gcode = 
	
	{% set layer = params.LAYER|int %}
	
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE={layer}
	SET_PRINT_STATS_INFO CURRENT_LAYER={layer}

[gcode_macro _LEARN_MORE_CALIBRATION]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/calibration" %}
	{% set link_text = "RatOS Calibration Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_CHAMBER_FILTER]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter Control" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_FILAMENT]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/filaments" %}
	{% set link_text = "RatOS Filament Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _CONSOLE_SAVE_CONFIG]
gcode = 
	M118 Click <a class="command text--blue">SAVE_CONFIG</a> to save the settings to your printer.cfg.

[gcode_macro _LOAD_RATOS_SKEW_PROFILE]
gcode = 
	{% set ratos_skew_profile = printer["gcode_macro RatOS"].skew_profile|default("") %}
	{% if ratos_skew_profile != "" %}
	{% if printer.fastconfig.config["skew_correction %s" % ratos_skew_profile] is defined %}
	SKEW_PROFILE LOAD={ratos_skew_profile}
	GET_CURRENT_SKEW
	{% else %}
	{% set line_1 = '"Could not find skew profile %s!_N_Clearing skew correction."' % ratos_skew_profile %}
	CONSOLE_ECHO TITLE="Missing skew profile!" TYPE="warning" MSG={line_1}
	SET_SKEW CLEAR=1
	{% endif %}
	{% endif %}

[gcode_macro M601]
gcode = 
	PAUSE

[gcode_macro _STOP_AND_RAISE_ERROR]
gcode = 
	M84
	_RAISE_ERROR MSG="{params.MSG}"

[gcode_macro _RESET_GCODE_VARIABLES]
description = Reset specified [gcode_macro ...] variables to their original values from configuration when Klipper started.
	- MACRO: Name of the GCODE macro containing the variables to reset.
	- VARIABLES: Comma-separated list of variable names to reset (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- QUIET: (optional) If true, suppresses console echo messages for each reset variable. Default is false.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set quiet = params.QUIET|default("false")|lower in ("true", "1", "yes") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	{% set settings = printer.fastconfig.settings[obj_name|lower] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro %s]" % macro) }
	{% endif %}
	
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if settings["variable_%s" % var] is not defined %}
	{ action_raise_error("Variable '%s' is not defined in settings for [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	
	{% for var in vars %}
	{% set var_value = obj[var] %}
	{% if var_value is defined %}
	{% set v = settings["variable_%s" % var] %}
	{% if v != var_value|string %}
	{% if var_value is string %}
	{% set v = '"\'' ~ v|replace('"', '\\"')|replace("'", "\\'") ~ '\'"' %}
	{% endif %}
	SET_GCODE_VARIABLE MACRO={macro} VARIABLE={var} VALUE={v}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Reset {macro} variable {var} to original value: {v} (was {obj[var]})"
	{% endif %}
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro _SHOW_GCODE_VARIABLES]
description = Show current values of specified [gcode_macro ...] variables.
	- MACRO: Name of the GCODE macro containing the variables to show.
	- VARIABLES: Comma-separated list of variable names to show (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- PAD: (optional) If defined, provide a single character to use for padding variable names to align values in a tabular format in the console output. Default is no padding.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set pad = params.PAD|default("") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	
	{% set ns = namespace() %}
	{% set ns.max_len = 0 %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% set ns.max_len = (ns.max_len, var|length)|max %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if pad %}
	{% set padding = pad * (ns.max_len - var|length) %}
	CONSOLE_ECHO MSG="{var}{padding} {obj[var]}"
	{% else %}
	CONSOLE_ECHO MSG="{var}: {obj[var]}"
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro PAUSE]
description = Pauses the print
rename_existing = PAUSE_BASE
variable_extrude = 1.5
variable_retract = 1.5
variable_fan_speed = 0
variable_idex_mode = ""
variable_idex_toolhead = 0
variable_idex_toolhead_x = 0.0
variable_idex_toolhead_y = 0.0
variable_idex_toolhead_z = 0.0
gcode = 
	RATOS_ECHO MSG="Pausing print..."
	
	
	{% set runout_detected = true if params.RUNOUT|default(false)|lower == 'true' else false %}
	
	
	_LED_PAUSE
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	SAVE_GCODE_STATE NAME=PAUSE_state
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_mode VALUE='"{idex_mode}"'
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={idex_toolhead}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_x VALUE={printer.gcode_move.gcode_position.x|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_y VALUE={printer.gcode_move.gcode_position.y|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_z VALUE={printer.gcode_move.gcode_position.z|float}
	DEBUG_ECHO PREFIX="PAUSE" MSG="idex_mode: {idex_mode}, idex_toolhead: {idex_toolhead}, idex_toolhead_x: {idex_toolhead_x}, idex_toolhead_y: {idex_toolhead_y}, idex_toolhead_z: {idex_toolhead_z}"
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="pause"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if current_z < (max_z - 20.0) %}
	{% set z_safe = 20.0 %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	PAUSE_BASE
	
	
	{% if printer["dual_carriage"] is not defined %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan"].speed|float}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	{% if idex_toolhead == 0 %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t1"].speed|float}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106 S0
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set R = printer["gcode_macro PAUSE"].retract|float %}
	{% if can_extrude %}
	G91
	G1 E-{R} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	{% set pause_print_park_x = printer["gcode_macro RatOS"].pause_print_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].pause_print_park_in %}
	{% if runout_detected %}
	{% set pause_print_park_x = printer["gcode_macro RatOS"].runout_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].runout_park_in %}
	{% endif %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	DEBUG_ECHO PREFIX="PAUSE" MSG="z_speed: {z_speed}, pause_print_park_x: {pause_print_park_x}, pause_print_park_in: {pause_print_park_in}, default_toolhead: {default_toolhead}"
	{% if "xyz" in printer.toolhead.homed_axes %}
	G91
	G1 Z{z_safe} F{z_speed}
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% else %}
	
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	_IDEX_SINGLE X={parking_position}
	{% else %}
	PARK_TOOLHEAD
	{% endif %}
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="pause"
	
	RATOS_ECHO MSG="Print paused"

[gcode_macro RESUME]
description = Resumes the print if the printer is paused.
rename_existing = RESUME_BASE
gcode = 
	
	
	RATOS_ECHO MSG="Resuming print..."
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	
	{% set target_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set target_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if target_idex_mode != '' %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set fan_speed = printer["gcode_macro PAUSE"].fan_speed|float %}
	{% if printer["dual_carriage"] is not defined %}
	M106 S{(fan_speed * 255)}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% else %}
	{% if params.TOOLHEAD is defined %}
	
	{% if params.TOOLHEAD == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% else %}
	{% if printer["gcode_macro PAUSE"].idex_toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	{% if params.TOOLHEAD is defined %}
	_SELECT_TOOL T={params.TOOLHEAD} X=-1 Y=-1 TOOLSHIFT=false
	{% else %}
	_SELECT_TOOL T={printer["gcode_macro PAUSE"].idex_toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	{% endif %}
	
	{% set x = printer["gcode_macro PAUSE"].idex_toolhead_x|float %}
	{% set y = printer["gcode_macro PAUSE"].idex_toolhead_y|float %}
	{% set z = printer["gcode_macro PAUSE"].idex_toolhead_z|float %}
	G1 X{x} Y{y} Z{z} F{speed}
	{% if params.TOOLHEAD is defined %}
	
	SAVE_GCODE_STATE NAME=PAUSE_STATE
	{% endif %}
	{% endif %}
	
	
	{% if params.TOOLHEAD is not defined %}
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% if can_extrude %}
	G91
	G1 E{E} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1 MOVE_SPEED={speed}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	RESUME_BASE
	
	
	_LED_PRINTING
	
	RATOS_ECHO MSG="Print resumed"

[gcode_macro CANCEL_PRINT]
description = Cancels the print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	RATOS_ECHO MSG="Cancelling print..."
	END_PRINT
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	
	CANCEL_PRINT_BASE
	RATOS_ECHO MSG="Print cancelled"

[gcode_macro START_PRINT]
description = Start print procedure, use this in your Slicer.
variable_post_processor_version = 2
variable_is_printing_gcode = False
variable_both_toolheads = True
variable_object_xoffset = 0
variable_first_x = -1
variable_first_y = -1
variable_total_toolshifts = 0
variable_initial_tool = 0
variable_extruder_first_layer_temp = ""
variable_extruder_other_layer_temp = ""
gcode = 
	
	{% if params.EXTRUDER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_TEMP parameter not found.")}
	{% endif %}
	{% if params.EXTRUDER_OTHER_LAYER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_OTHER_LAYER_TEMP parameter not found.")}
	{% endif %}
	{% if params.BED_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. BED_TEMP parameter not found.")}
	{% endif %}
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' and printer["gcode_macro RatOS"].danger_force_allow_auto_center_subject|default(false)|lower != 'true'%}
	
	
	
	
	
	{ action_raise_error("The experimental auto_center_subject feature is not supported in this version of RatOS. Please disable it in the RatOS macro settings.") }
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes and printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% if printer["gcode_macro _VAOC"].is_started|default(true)|lower == 'true' %}
	_VAOC_END
	{% endif %}
	{% endif %}
	
	
	_LED_START_PRINTING
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_USER_START_PRINT { rawparams }
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_probe_stowable = printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% endif %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	{% set X0 = params.X0|default(-1)|float %}
	{% set X1 = params.X1|default(-1)|float %}
	{% set Y0 = params.Y0|default(-1)|float %}
	{% set Y1 = params.Y1|default(-1)|float %}
	{% if first_x == -1 or first_y == -1 %}
	{% set first_x = params.FIRST_X|default(-1)|float %}
	{% set first_y = params.FIRST_Y|default(-1)|float %}
	{% endif %}
	{% set total_toolshifts = params.TOTAL_TOOLSHIFTS|default(0)|int %}
	{% set initial_tool = params.INITIAL_TOOL|default(default_toolhead)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	
	
	
	
	
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(printer.heater_bed.target, true)|float %}
	
	
	{% set total_layer_count = params.TOTAL_LAYER_COUNT|default(0)|int %}
	{% set extruder_first_layer_temp = (params.EXTRUDER_TEMP|default("")).split(",") %}
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL BEACON_CONTACT_START_PRINT_TRUE_ZERO={beacon_contact_start_print_true_zero} BEACON_CONTACT_CALIBRATE_MODEL_ON_TRUE_ZERO={beacon_contact_calibrate_model_on_true_zero}
	{% endif %}
	
	_START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH BED_TEMP={bed_temp}
	
	
	RATOS_ECHO MSG="First print coordinates X:{first_x} Y:{first_y}"
	
	
	{% if params.TOTAL_LAYER_COUNT is not defined %}
	{% set link_url = "https://os.ratrig.com/docs/slicers" %}
	{% set link_text = "RatOS Slicer Configuration" %}
	{% set line_1 = '"Your slicer gcode settings are not up to date._N_Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="Incomplete Slicer Configuration detected" TYPE="warning" MSG={line_1}
	{% endif %}
	
	
	SET_PRINT_STATS_INFO CURRENT_LAYER=1
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE=1
	{% if total_layer_count > 0 %}
	SET_PRINT_STATS_INFO TOTAL_LAYER={total_layer_count}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads %}
	{% set initial_tool = 0 if initial_tool == 1 else 1 %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	{% endif %}
	
	
	{% set both_toolheads = true %}
	{% if total_toolshifts == 0 %}
	{% set both_toolheads = false %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	{% endif %}
	{% if both_toolheads and (idex_mode == "copy" or idex_mode == "mirror") %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Gcode tool changes found. Copy and mirror mode do not support toolchanges.")}
	{% endif %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set both_toolheads = true %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=initial_tool VALUE={initial_tool}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_x VALUE={first_x}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_y VALUE={first_y}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=total_toolshifts VALUE={total_toolshifts}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=both_toolheads VALUE={both_toolheads}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_first_layer_temp VALUE="'{params.EXTRUDER_TEMP}'"
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_other_layer_temp VALUE="'{params.EXTRUDER_OTHER_LAYER_TEMP}'"
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE=0
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set svv = printer.save_variables.variables %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set stepper_x_position_min = printer.fastconfig.settings.stepper_x.position_min|float %}
	{% set stepper_x_position_endstop = printer.fastconfig.settings.stepper_x.position_endstop|float %}
	{% set dual_carriage_position_max = printer.fastconfig.settings.dual_carriage.position_max|float %}
	{% set dual_carriage_position_endstop = printer.fastconfig.settings.dual_carriage.position_endstop|float %}
	{% set x_parking_space = parking_position_t0 - (stepper_x_position_endstop , stepper_x_position_min)|max %}
	{% set dc_parking_space = (dual_carriage_position_endstop , dual_carriage_position_max)|min - parking_position_t1 %}
	{% if svv.idex_xoffset|abs >= (x_parking_space - 0.5) or svv.idex_xoffset|abs >= (dc_parking_space - 0.5) %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Toolhead x-offset is too high for the available parking space. Calibrate your X and DC endstop positions and make sure you stay below 1mm." % (copy_mode_max_width)) }
	{% endif %}
	{% endif %}
	
	
	{% if (idex_mode == "copy" or idex_mode == "mirror") and printer.fastconfig.settings.ratos.enable_gcode_transform %}
	
	{% if params.MIN_X is not defined or params.MAX_X is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Something went wrong! Missing important post processor start print parameter!") }
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE=0
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	
	{% set boundary_box_min_x = params.MIN_X|default(0)|float %}
	{% set boundary_box_max_x = params.MAX_X|default(printable_x_max)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if default_toolhead == 0 %}
	
	{% set boundary_box_max_x = boundary_box_max_x + svv.idex_xoffset %}
	{% else %}
	
	{% set boundary_box_min_x = boundary_box_min_x - svv.idex_xoffset %}
	{% endif %}
	
	{% set center_x = printable_x_max / 2.0 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set object_width = boundary_box_max_x - boundary_box_min_x %}
	{% set copy_mode_max_width = center_x %}
	{% set mirror_mode_max_width = center_x - safe_distance / 2.0 %}
	
	DEBUG_ECHO PREFIX="START_PRINT" MSG="OBJECT_WIDTH: {object_width} BOUNDARY_BOX_MIN_X: {boundary_box_min_x} BOUNDARY_BOX_MAX_X: {boundary_box_max_x} CENTER_X: {center_x} SAFE_DISTANCE: {safe_distance}"
	
	
	{% if idex_mode == "copy" and object_width > copy_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for copy mode! Max supported width is %s mm" % (copy_mode_max_width)) }
	{% endif %}
	{% if idex_mode == "mirror" and object_width > mirror_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for mirror mode! Max supported width is %s mm" % (mirror_mode_max_width)) }
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = (printable_x_max - boundary_box_max_x - boundary_box_min_x) / 2 %}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE={object_xoffset}
	{% endif %}
	
	{% endif %}
	
	
	{% set has_initial_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_toolhead_filament_sensor %}
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% set has_initial_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_bowden_filament_sensor %}
	
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% if printer["dual_carriage"] is defined and both_toolheads %}
	
	{% set has_secondary_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set has_secondary_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_CHAMBER_FILTER_ON AT="before_print_start"
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true' %}
	{% if both_toolheads %}
	RATOS_ECHO MSG="Spool join is not possible if both toolheads are in use!"
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	{% endif %}
	
	
	CLEAR_PAUSE
	{% if printer["gcode_macro RatOS"].force_absolute_position|lower == 'true' %}
	G90
	{% endif %}
	SAVE_GCODE_STATE NAME=start_print_state
	
	
	G21
	
	G90
	
	M82
	_USER_START_PRINT_BEFORE_HOMING { rawparams }
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_BEGIN_BATCH
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_Z_HOP
	
	
	{% if idex_mode != '' and not (printer.fastconfig.settings.beacon is defined and (beacon_contact_start_print_true_zero or beacon_adaptive_heat_soak)) %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	{% if chamber_temp > 0 %}
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED={printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float}
	{% endif %}
	{% endif %}
	_CHAMBER_HEATER_ON START_CHAMBER_TEMP={start_chamber_temp} CHAMBER_TEMP={chamber_temp}
	_USER_START_PRINT_HEAT_CHAMBER { rawparams } CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_START_PRINT_BEFORE_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	RATOS_ECHO MSG="Heating bed..."
	
	M190 S{bed_temp}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_adaptive_heat_soak %}
	_MOVE_TO_SAFE_Z_HOME
	
	G1 Z2.5 F{z_speed}
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK LAYER_QUALITY={beacon_adaptive_heat_soak_layer_quality} MAXIMUM_FIRST_LAYER_DURATION={beacon_adaptive_heat_soak_maximum_first_layer_duration} MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={beacon_adaptive_heat_soak_max_wait}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_BED { rawparams }
	
	
	_START_PRINT_AFTER_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	_USER_START_PRINT_BED_MESH { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_BED_MESH X0={X0} X1={X1} Y0={Y0} Y1={Y1} T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_END_BATCH
	{% endif %}
	
	
	{% if idex_mode == '' %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[initial_tool]|float}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[0]|float}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={extruder_first_layer_temp[1]|float}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_PARK { rawparams }
	
	
	_START_PRINT_PARK
	
	
	RATOS_ECHO MSG="Heating Extruder..."
	{% if idex_mode == '' %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[initial_tool]|float}  MAXIMUM={extruder_first_layer_temp[initial_tool]|float + 5}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[0]|float}  MAXIMUM={extruder_first_layer_temp[0]|float + 5}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder1" MINIMUM={extruder_first_layer_temp[1]|float}  MAXIMUM={extruder_first_layer_temp[1]|float + 5}
	{% endif %}
	{% endif %}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	{% if idex_mode == '' %}
	_LED_PRINTING
	{% else %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	_LED_PRINTING
	{% else %}
	{% if both_toolheads %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	{% if toolchange_standby_temp > -1 %}
	_LED_TOOLHEAD_STANDBY TOOLHEAD={0 if initial_tool == 1 else 1}
	{% else %}
	_LED_PRINTING TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% else %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_EXTRUDER { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_AFTER_HEATING_EXTRUDER X0={X0} X1={X1} Y0={Y0} Y1={Y1} INITIAL_TOOLHEAD={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if idex_mode != '' %}
	{% if not both_toolheads %}
	{% if initial_tool != default_toolhead %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if idex_mode != '' %}
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=standby VALUE=False
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=standby VALUE=False
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if initial_tool == 1 else 'extruder1'} TARGET={toolchange_standby_temp}
	SET_GCODE_VARIABLE MACRO=T{0 if initial_tool == 1 else 1} VARIABLE=standby VALUE=True
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=start_print_state
	
	{% if printer["dual_carriage"] is defined %}
	_SET_IDEX_MODE_OFFSET
	{% endif %}
	
	
	{% if idex_mode != '' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% if idex_mode == "copy" and idex_mode != act_idex_mode %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == "mirror" and idex_mode != act_idex_mode %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={object_xoffset} MOVE=0
	{% endif %}
	{% else %}
	_SELECT_TOOL T={initial_tool} TOOLSHIFT=false
	_SET_TOOLHEAD_OFFSET
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	_SET_EXTRUSION_MODE
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={printer["print_stats"].print_duration}
	{% endif %}
	
	
	_USER_END_START_PRINT { rawparams }
	
	G92 E0
	
	
	_CHAMBER_FILTER_ON AT="after_print_start"
	
	_ALERT_NON_ZERO_Z_OFFSET
	
	RATOS_ECHO MSG="Printing..."

[gcode_macro _START_PRINT_BEFORE_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set is_stowable_probe = true if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' else false %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Pre-heating extruder..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={min_temp}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET={min_temp}
	{% endif %}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	{% endif %}
	{% endif %}
	
	
	{% if not is_stowable_probe %}
	{% if printer["dual_carriage"] is defined and act_t != default_toolhead %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	{% endif %}
	RATOS_ECHO MSG="Heat soaking z probe..."
	_MOVE_TO_SAFE_Z_HOME
	
	G0 Z2 F{z_speed}
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Waiting for extruder to be preheated..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	{% if default_toolhead == 0 %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_Z_HOP
	{% endif %}
	
	
	{% if auto_z_offset_calibration %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	PARK_TOOLHEAD
	_CLEANING_MOVE TOOLHEAD={default_toolhead} AUTOMATED=True
	_SELECT_TOOL T={0 if default_toolhead == 1 else 1} X={parking_position_t0 if default_toolhead == 1 else parking_position_t1} Y=0 TOOLSHIFT=false
	_CLEANING_MOVE TOOLHEAD={0 if default_toolhead == 1 else 1} AUTOMATED=True
	_VAOC_CALIBRATE_Z_OFFSET AUTO_Z_OFFSET=True
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=false
	{% endif %}
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	{% if needs_rehoming %}
	G28 Z
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	_START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE
	{% endif %}
	{% endif %}
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	PROBE PROBE_METHOD=contact SAMPLES=1

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	{% set fuzzy_radius = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_radius|default(0)|float if beacon_contact_start_print_true_zero_fuzzy_position else 0 %}
	
	{% set contact_true_zero_temp_has_been_set = False %}
	
	
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	
	
	
	{% if printer.beacon.last_probe_result|lower == "ok" %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	RATOS_ECHO MSG="Auto calibration nozzle wipe with probe result {last_z_offset}..."
	G0 Z{(0.2 + last_z_offset)} F{z_speed}
	G0 X70 F300
	{% else %}
	RATOS_ECHO MSG="Skipping auto calibration nozzle wipe because probing failed!"
	{% endif %}
	{% elif beacon_contact_wipe_before_true_zero_method == "probe_clean" %}
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	
	{% set contact_true_zero_temp_has_been_set = True %}
	
	
	
	
	
	
	
	
	BEACON_PROBE_CLEAN X=50 Y=10
	{% else %}
	CONSOLE_ECHO TYPE="error" TITLE="Unknown wipe method" MSG="Unknown wipe method '{beacon_contact_wipe_before_true_zero_method}' configured, skipping wipe before beacon true zero."
	{% endif %}
	{% endif %}
	
	
	G0 Z5 F{z_speed}
	_MOVE_TO_SAFE_Z_HOME FUZZY_RADIUS={fuzzy_radius}
	
	
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION
	
	{% if not contact_true_zero_temp_has_been_set %}
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon contact auto calibration..."
	
	{% if beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	
	G0 Z5 F{z_speed}

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION]
gcode = 
	{% set pos = printer.ratos.last_move_to_safe_z_home_position %}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE={pos[0]}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE={pos[1]}

[gcode_macro _START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set first_x = printer["gcode_macro START_PRINT"].first_x|default(-1)|float %}
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2.0 %}
	{% set center_y = printable_y_max / 2.0 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% if printer["dual_carriage"] is defined %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% endif %}
	
	
	{% set X0 = params.X0|default(-1)|int %}
	{% set X1 = params.X1|default(-1)|int %}
	{% set Y0 = params.Y0|default(-1)|int %}
	{% set Y1 = params.Y1|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	
	{% if idex_mode == '' %}
	
	_PRIME
	{% else %}
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	RATOS_ECHO PREFIX="IDEX" MSG="using combined prime offset for IDEX {idex_mode} mode"
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	{% if both_toolheads %}
	{% if initial_toolhead == 0 %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T{initial_toolhead}"
	_SELECT_TOOL T={initial_toolhead} TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	SET_MACRO_TRAVEL_SETTINGS
	
	{% if (X0 > -1 and Y1 > -1) or (first_x > 0 and first_y > 0) %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	{% endif %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	{% set first_z = 1 %}
	{% else %}
	{% set first_z = 3 %}
	{% endif %}
	
	
	{% if idex_mode == "mirror" %}
	{% if first_y >= 0 %}
	G0 Y{first_y} F{speed}
	{% else %}
	G0 Y{Y1} F{speed}
	{% endif %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={initial_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={initial_toolhead} E={printer["gcode_macro RatOS"].toolchange_first_purge|default(50)|float}
	_CLEANING_MOVE TOOLHEAD={initial_toolhead} AUTOMATED=True
	{% endif %}
	{% if first_x >= 0 and first_y >= 0 %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% else %}
	{% set first_x = X0 %}
	{% set first_y = Y0 %}
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'min' %}
	{% set first_x = X0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'max' %}
	{% set first_x = X1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|float <= center_x %}
	{% set first_x = X0 %}
	{% else %}
	{% set first_x = X1 %}
	{% endif %}
	{% endif %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'min' %}
	{% set first_y = Y0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'max' %}
	{% set first_y = Y1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|float <= center_y %}
	{% set first_y = Y0 %}
	{% else %}
	{% set first_y = Y1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	
	
	_LOAD_RATOS_SKEW_PROFILE

[gcode_macro _PRIME]
gcode = 
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	PRIME_BLOB INITIAL_TOOLHEAD={params.INITIAL_TOOLHEAD} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={params.IDEX_MODE} Y1={params.Y1}
	{% else %}
	
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif params.IDEX_MODE == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro END_PRINT]
description = End print procedure, use this in your Slicer.
gcode = 
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SAVE_GCODE_STATE NAME=end_print_state
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = printer["gcode_macro START_PRINT"].object_xoffset|default(0)|float %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(0-object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={(0-object_xoffset)}
	{% endif %}
	{% endif %}
	
	
	_USER_END_PRINT_BEFORE_HEATERS_OFF { rawparams }
	_END_PRINT_BEFORE_HEATERS_OFF
	TURN_OFF_HEATERS
	_USER_END_PRINT_AFTER_HEATERS_OFF { rawparams }
	_END_PRINT_AFTER_HEATERS_OFF
	_USER_END_PRINT_PARK { rawparams }
	_END_PRINT_PARK
	
	
	{% if printer["gcode_macro RatOS"].skew_profile is defined %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined and printer["gcode_macro RatOS"].end_print_motors_off|lower != 'false' %}
	
	M84
	{% endif %}
	
	
	M107
	
	
	BED_MESH_CLEAR
	RATOS_ECHO MSG="Done :)"
	
	
	RESTORE_GCODE_STATE NAME=end_print_state
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	M84
	{% endif %}
	
	
	RESET_NAMED_OFFSET EVENT="end_print"
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_CHAMBER_FILTER_ON AT="print_end"
	_CHAMBER_FILTER_OFF
	
	
	_CHAMBER_HEATER_OFF
	
	_USER_END_PRINT_FINISHED { rawparams }

[gcode_macro _END_PRINT_BEFORE_HEATERS_OFF]
gcode = 
	RATOS_ECHO MSG="Cleaning up..."

[gcode_macro _END_PRINT_AFTER_HEATERS_OFF]
gcode = 
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% set z_hop = printer["gcode_macro RatOS"].end_print_park_z_hop|float %}
	{% set r = printer["gcode_macro RatOS"].end_print_retract_filament|default(4)|float %}
	{% if current_z < (max_z - z_hop) %}
	{% set z_safe = z_hop %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G91
	
	{% if can_extrude %}
	G1 E-2 F3600
	{% endif %}
	
	G0 Z{z_safe} F3600
	
	{% if can_extrude %}
	G1 E-{(r-2)} F3600
	{% endif %}
	
	G90

[gcode_macro _SET_EXTRUSION_MODE]
gcode = 
	
	{% if printer["gcode_macro RatOS"].relative_extrusion|lower == 'true' %}
	M83
	{% else %}
	M82
	{% endif %}

[gcode_macro GENERATE_SHAPER_GRAPHS]
description = Genarates input shaper resonances graphs for analysis. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	{% set hz_per_sec = params.HZ_PER_SEC|default(1)|float %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set copy_mode_offset = printable_x_max / 4.0 %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	_IDEX_SINGLE
	{% endif %}
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	
	
	{% if idex_mode != 'copy' and idex_mode != 'mirror' %}
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	{% endif %}
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Shaper graph"

[gcode_shell_command generate_shaper_graph_x]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-x.sh
timeout = 60.
verbose = True

[gcode_shell_command generate_shaper_graph_y]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-y.sh
timeout = 60.
verbose = True

[gcode_macro MEASURE_COREXY_BELT_TENSION]
description = Generates resonance graph used to ensure belts are equally tensioned. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	_IDEX_SINGLE
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if measure_t1 == false or measure_t0 == false %}
	{action_raise_error("Axis specified. Not supported for belt tension on Y.")}
	{% else %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	G4 P5000
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	PARK_TOOLHEAD
	{% endif %}
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	G1 X{parking_position_t1} F{speed}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	
	
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Belt Tension Graph"

[gcode_shell_command generate_belt_tension_graph]
command = /home/pi/printer_data/config/RatOS/scripts/generate-belt-tension-graph.sh
timeout = 90.
verbose = True

[idle_timeout]
gcode = 
	{% if printer.webhooks.state|lower == 'ready' %}
	{% if printer.pause_resume.is_paused|lower == 'false' %}
	_USER_BEFORE_IDLE_TIMEOUT
	RATOS_ECHO PREFIX="IDLE" MSG="2 hours since last activity. Powering off heaters and motors.."
	TURN_OFF_HEATERS
	M84
	_USER_AFTER_IDLE_TIMEOUT
	{% endif %}
	{% endif %}
timeout = 7200

[temperature_sensor raspberry_pi]
sensor_type = temperature_host

[skew_correction]

[named_offsets]

[input_shaper]

[virtual_sdcard]
path = ~/printer_data/gcodes

[display_status]

[pause_resume]

[force_move]
enable_force_move = True

[respond]

[resonance_generator]

[ratos]
allow_unknown_gcode_generator = True
enable_gcode_transform = True

[exclude_object]

[bed_mesh]
split_delta_z = 0.001
horizontal_move_z = 2
mesh_min = 20,20
mesh_max = 480,480
probe_count = 40,40
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = .2
speed = 600
log_points = False

[fastconfig]

[heater_bed]
heater_pin = heater_bed_heating_pin
sensor_pin = heater_bed_sensor_pin
sensor_type = Generic 3950
min_temp = 0
max_temp = 140
pwm_cycle_time = 0.103
control = pid
pid_kp = 61.987
pid_ki = 1.781
pid_kd = 539.289

[printer]
kinematics = ratos_hybrid_corexy
max_velocity = 800
max_accel = 10000
minimum_cruise_ratio = 0.5
max_z_velocity = 50
max_z_accel = 600
square_corner_velocity = 5

[ratos_hybrid_corexy]
inverted = true

[dual_carriage]
axis = x
safe_distance = 55
position_max = 559.6
position_endstop = 559.6
position_min = 0
step_pin = PF9
dir_pin = dual_carriage_dir_pin
enable_pin = !PG2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t1:PA2

[gcode_macro _SET_IDEX_MODE_OFFSET]
description = "Internal use only. Sets the 'idex_mode' named offset that the active idex mode requires."
gcode = 
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_SET_IDEX_MODE_OFFSET" MSG="idex_mode: {idex_mode}, center_x: {center_x}"
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	SET_NAMED_OFFSET NAME=idex_mode X={(-center_x / 2)}
	{% else %}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% else %}
	{action_raise_error("_SET_IDEX_MODE_OFFSET: Printer not homed")}
	{% endif %}

[gcode_macro IDEX_SINGLE]
gcode = 
	_IDEX_REMAP_TOOLHEADS ENABLE=False
	_IDEX_SINGLE

[gcode_macro _IDEX_SINGLE]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_single"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set init = params.INIT|default(0)|int %}
	{% set new_x = params.X|default(-1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_default_t = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="init: {init}, new_x: {new_x}, idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, act_t: {act_t}"
	
	{% if idex_mode == "copy" or idex_mode == "mirror" or init == 1 %}
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="reset idex_mode offset"
	G1 X{center_x} F{(speed)}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="activate default carriage"
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolheads"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	G90
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position."
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1}
	G1 X{parking_position_default_t} F{speed}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move default toolhead to its new position."
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% if new_x == -1 %}
	{% set new_x = center_x %}
	{% endif %}
	G1 X{new_x} F{speed}
	
	M400
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="X Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set extruder motion queue."
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if default_toolhead==0 else default_toolhead}
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolhead offset."
	_SET_TOOLHEAD_OFFSET
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set input shaper."
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[default_toolhead]|float)} SHAPER_FREQ_Y={(shaper_y_freq[default_toolhead]|float)} SHAPER_TYPE_X={(shaper_x_type[default_toolhead]|lower)} SHAPER_TYPE_Y={(shaper_y_type[default_toolhead]|lower)}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="update Frontend."
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if default_toolhead==0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if default_toolhead==1 else False}
	{% else %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_single"

[gcode_macro IDEX_COPY]
gcode = 
	_IDEX_COPY

[gcode_macro _IDEX_COPY]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_copy"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set y = params.Y|default(-1)|int %}
	{% set dance = params.DANCE|default(1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_COPY" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}, y: {y}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "copy" %}
	{% if idex_mode == "mirror" %}
	{% if y>=0 %}
	G1 X{center_x} Y{y} F{(speed)}
	{% else %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	
	
	{% if idex_mode != "mirror" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance == 1 %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[2]|float)} SHAPER_FREQ_Y={(shaper_y_freq[2]|float)} SHAPER_TYPE_X={(shaper_x_type[2]|lower)} SHAPER_TYPE_Y={(shaper_y_type[2]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_copy"

[gcode_macro IDEX_MIRROR]
gcode = 
	_IDEX_MIRROR

[gcode_macro _IDEX_MIRROR]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_mirror"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set dance = params.DANCE|default(1)|int %}
	{% set priming = params.PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_MIRROR" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "mirror" %}
	
	{% if idex_mode == "copy" %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS MIRROR_PRIMING={params.PRIMING}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=MIRROR
	
	
	{% if idex_mode != "copy" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance and not priming %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[3]|float)} SHAPER_FREQ_Y={(shaper_y_freq[3]|float)} SHAPER_TYPE_X={(shaper_x_type[3]|lower)} SHAPER_TYPE_Y={(shaper_y_type[3]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_mirror"

[gcode_macro _IDEX_SET_TOOLHEADS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set mirror_priming = params.MIRROR_PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position_inactive_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_IDEX_SET_TOOLHEADS" MSG="idex_mode: {idex_mode}, act_t: {act_t}, center_x: {center_x}, mirror_priming: {mirror_priming}"
	
	
	{% if act_t != default_toolhead %}
	_SET_TOOLHEAD_OFFSET FORCE_TOOLHEAD={default_toolhead} MOVE=1
	{% endif %}
	
	{% if mirror_priming %}
	
	
	
	{% if parking_position_t0|abs < parking_position_t1 - printable_x_max %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{printable_x_max + parking_position_t0|abs} F{(speed)}
	{% else %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{0 - (parking_position_t1 - printable_x_max)} F{(speed)}
	{% endif %}
	
	{% else %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1} MODE=PRIMARY
	G1 X{parking_position_inactive_t} F{(speed)}
	
	
	{% if act_t==1 %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{center_x / 2} F{(speed)}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"

[gcode_macro IDEX_PARK]
gcode = 
	
	PARK_TOOLHEAD

[gcode_macro PARK_TOOLHEAD]
gcode = 
	
	{% set idex_mode = 'none' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="PARK_TOOLHEAD" MSG="Parking T{act_t}.."
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set parking_position_inact_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set printable_y_min = printer["gcode_macro RatOS"].printable_y_min|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" and 'xy' in printer.toolhead.homed_axes %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% elif printer.toolhead.position.y|float < printable_y_min %}
	G1 Y{printable_y_min} F{speed}
	{% endif %}
	
	SAVE_GCODE_STATE NAME=_PARK_TOOLHEAD
	G90
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0.5
	
	
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_inact_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	
	SET_VELOCITY_LIMIT ACCEL={printer.toolhead.max_accel} MINIMUM_CRUISE_RATIO=0.5
	M400
	RESTORE_GCODE_STATE NAME=_PARK_TOOLHEAD
	
	{% endif %}

[gcode_macro JOIN_SPOOLS]
gcode = 
	
	{% set spools = params.SPOOLS|default("") %}
	
	{% if spools == "" %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% else %}
	{% if spools != "0,1" and spools != "1,0" %}
	RATOS_ECHO MSG="Wrong spool configuration!"
	RATOS_ECHO MSG="Join Spools = JOIN_SPOOLS SPOOLS=0,1"
	RATOS_ECHO MSG="Deactivate = JOIN_SPOOLS SPOOLS="
	{% else %}
	{% if spools == "0,1" or spools == "1,0" %}
	_IDEX_JOIN_SPOOLS ENABLE=true
	{% else %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_JOIN_SPOOLS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if enable %}
	{% set has_t0_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t1_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t0_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined else false %}
	{% set has_t1_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined else false %}
	{% if (has_t0_toolhead_filament_sensor and has_t1_toolhead_filament_sensor) or (has_t0_bowden_filament_sensor and has_t1_bowden_filament_sensor) %}
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=True
	RATOS_ECHO MSG="Spool joining enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Can not enable spool joining! No filament sensors found."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining deactivated!"
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining is not possible in copy and mirror mode!"
	{% endif %}

[gcode_macro _JOIN_SPOOL]
gcode = 
	
	{% set old_toolhead = params.TOOLHEAD|int %}
	{% set new_toolhead = 0 if old_toolhead == 1 else 1 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set purge_after_load = printer["gcode_macro T%s" % new_toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_JOIN_SPOOL" MSG="toolhead: {new_toolhead}"
	
	{% set has_filament = true %}
	{% set has_new_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% set has_new_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% if has_new_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	{% if has_new_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	
	{% if has_filament %}
	RATOS_ECHO MSG="Joining spools! Please wait for extruder to heat up...."
	
	
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={new_toolhead}
	
	
	_DEACTIVATE_TOOLHEAD TOOLHEAD={old_toolhead}
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set extruder_temp = extruder_first_layer_temp[new_toolhead]|float %}
	{% else %}
	{% set extruder_temp = extruder_other_layer_temp[new_toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if new_toolhead == 0 else 'extruder1'} TARGET={extruder_temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if new_toolhead == 0 else 'extruder1'} MINIMUM={extruder_temp}  MAXIMUM={extruder_temp + 5}
	
	
	{% if purge_after_load > 0 %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_toolhead == 0 else new_toolhead}
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={new_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={new_toolhead} E={purge_after_load}
	_CLEANING_MOVE TOOLHEAD={new_toolhead} AUTOMATED=True
	
	
	SET_DUAL_CARRIAGE CARRIAGE={old_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if old_toolhead == 0 else old_toolhead}
	
	{% endif %}
	
	
	RESUME TOOLHEAD={new_toolhead}
	
	
	_IDEX_JOIN_SPOOLS ENABLE=false
	
	{% else %}
	{ action_raise_error("Spool join failed! No filament found or filament sensor is disabled.") }
	{% endif %}

[gcode_macro REMAP_TOOLHEADS]
gcode = 
	
	{% set toolheads = params.TOOLHEADS|default("") %}
	
	{% if toolheads == "" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% else %}
	{% if toolheads != "0,1" and toolheads != "1,0" %}
	RATOS_ECHO MSG="Wrong toolhead configuration!"
	RATOS_ECHO MSG="Remap = REMAP_TOOLHEADS TOOLHEADS=0,1"
	RATOS_ECHO MSG="Deactivate = REMAP_TOOLHEADS TOOLHEADS="
	{% else %}
	{% if toolheads == "0,1" or toolheads == "1,0" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=true
	_IDEX_SINGLE
	{% else %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_REMAP_TOOLHEADS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	{% if not enable or (idex_mode != "copy" and idex_mode != "mirror") %}
	{% if enable %}
	RATOS_ECHO MSG="Toolhead remapping enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping deactivated!"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE={enable}
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping not possible in copy and mirror mode!"
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	{% endif %}

[gcode_macro SHAPER_CALIBRATE]
rename_existing = SHAPER_CALIBRATE_ORG
gcode = 
	RATOS_ECHO PREFIX="IDEX" MSG="SHAPER_CALIBRATE is useless on IDEX machines. Please use the GENERATE_SHAPER_GRAPHS macro and type the values into `variable_shaper_*_freq` and `variable_shaper_*_type manually`."

[gcode_shell_command generate_shaper_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-shaper-graph.sh
timeout = 120.
verbose = True

[gcode_shell_command generate_tension_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-belt-tension-graph.sh
timeout = 120.
verbose = True

[gcode_macro SET_PRESSURE_ADVANCE]
variable_snyc_toolheads = False
rename_existing = SET_PRESSURE_ADVANCE_BASE
gcode = 
	{% if params.SYNC_TOOLHEADS is defined %}
	{% set snyc_toolheads = true if params.SYNC_TOOLHEADS|default(false)|lower == 'true' else false %}
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=True
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="Syncing toolheads..."
	{% else %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' or snyc_toolheads %}
	{% set advance = params.ADVANCE|default(printer['extruder'].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['extruder'].smooth_time|float)|float %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T0"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T1"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder1' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% else %}
	{% set extruder = 'extruder' if act_t == 0 else 'extruder1' %}
	{% if params.EXTRUDER is defined %}
	{% set extruder = params.EXTRUDER %}
	{% endif %}
	{% if extruder == 'extruder' or extruder == 'extruder1' %}
	{% set advance = params.ADVANCE|default(printer['%s' % extruder].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['%s' % extruder].smooth_time|float)|float %}
	SET_PRESSURE_ADVANCE_BASE EXTRUDER={extruder} ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% if params.EXTRUDER is not defined %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG={"T%s" % act_t}
	{% endif %}
	{% else %}
	SET_PRESSURE_ADVANCE_BASE { rawparams }
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro M106]
rename_existing = M106.1
variable_swap_speed = -1
gcode = 
	
	{% set s = [[params.S|default(255)|int, 255]|min, 0]|max %}
	{% set p = params.P|default(-1)|int %}
	{% set speed = s / 255 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set t = 1 if idex_mode=='primary' else 0 %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(0)|int == 1 else false %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set sync_fans = true %}
	{% endif %}
	
	
	{% if sync_fans and idex_mode != "copy" and idex_mode != "mirror" %}
	
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int %}
	
	
	{% if toolshift_count > total_toolshifts %}
	{% set sync_fans = false %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE=-1
	
	
	{% if p == -1 %}
	
	{% if speed == 0 %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed}
	{% else %}
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE={speed}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={(speed if (t == 0 or sync_fans) else 0)}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={(speed if (t == 1 or sync_fans) else 0)}
	{% endif %}
	{% else %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed if t == p else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed if t == p else 0}
	{% endif %}
	
	
	M106.1 S{s}

[gcode_macro M107]
rename_existing = M107.1
gcode = 
	{% set p = params.P|default(-1)|int %}
	M106 S0 P{p}

[gcode_macro _SELECT_TOOL]
variable_last_timestamp = 0
gcode = 
	{% if params.T is defined %}
	{% set idex_mode = '' %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if "xyz" not in printer.toolhead.homed_axes and (idex_mode == "copy" or idex_mode == "mirror") %}
	_IDEX_SINGLE
	{% set idex_mode = 'reset' %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set new_t = params.T|int %}
	
	
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads and is_printing_gcode %}
	{% set new_t = 0 if new_t == 1 else 1 %}
	{% endif %}
	
	
	{% set toolchange_prepurging_timer = printer["gcode_macro RatOS"].toolchange_prepurging_timer|default(0)|int %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	DEBUG_ECHO PREFIX="_SELECT_TOOL" MSG="act_t: {act_t}, new_t: {new_t}, is_printing_gcode: {is_printing_gcode}, swap_toolheads: {swap_toolheads}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	{% set act_extruder = 'extruder%s' % ('' if new_t == 0 else new_t) %}
	{% if new_t != act_t or printer.toolhead.extruder != act_extruder or idex_mode == 'reset' %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Selecting T{new_t}.."
	
	
	M220 S100
	
	
	
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(1)|int == 1 else false %}
	
	
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set toolshift = false %}
	{% endif %}
	
	
	{% set fan_speed = printer["fan_generic part_fan_t%s" % act_t].speed %}
	
	
	{% set deactivate_toolhead = false %}
	{% if is_printing_gcode %}
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int + 1 %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE={toolshift_count}
	{% if toolshift_count == total_toolshifts %}
	{% set deactivate_toolhead = true %}
	{% endif %}
	{% endif %}
	
	
	{% set needs_wakeup = true if printer["gcode_macro T%s" % new_t].standby|default(false)|lower == 'true' else false %}
	
	
	{% set needs_purging = false %}
	{% set wake_up_purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% if is_printing_gcode and toolchange_prepurging_timer > 0 and wake_up_purge > 0 %}
	{% set new_timestamp = printer["print_stats"].print_duration %}
	{% set elapsed_time = new_timestamp - last_timestamp %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={new_timestamp}
	{% if elapsed_time > toolchange_prepurging_timer %}
	{% set needs_purging = true %}
	{% endif %}
	{% endif %}
	
	
	{% set first_use_purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% if toolshift_count == 1 and first_use_purge > 0 %}
	{% set needs_purging = true %}
	{% endif %}
	
	
	{% if is_printing_gcode and (toolchange_standby_temp > -1 or needs_purging or needs_wakeup) %}
	_TOOLHEAD_STANDBY TOOLHEAD={act_t}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	_TOOLHEAD_WAKEUP TOOLHEAD={new_t} X={new_x} Y={new_y} Z={new_z} FAN_SPEED={fan_speed} TOOLSHIFT_COUNT={toolshift_count}
	{% else %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(false)|lower == 'true' else false %}
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if (new_t == 0 or sync_fans) else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if (new_t == 1 or sync_fans) else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	_TOOLCHANGE T={new_t} X={new_x} Y={new_y} Z={new_z} PARK_T0={park_t0} PARK_T1={park_t1} TOOLSHIFT={toolshift}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[new_t]|float)} SHAPER_FREQ_Y={(shaper_y_freq[new_t]|float)} SHAPER_TYPE_X={(shaper_x_type[new_t]|lower)} SHAPER_TYPE_Y={(shaper_y_type[new_t]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if new_t == 0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if new_t == 1 else False}
	
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% set sanity_check_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if new_t == 0 %}
	{% if printer.toolhead.extruder == 'extruder' %}
	{% if sanity_check_idex_mode == 'primary' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% elif new_t == 1 %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% if sanity_check_idex_mode == 'inactive' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _TOOLHEAD_STANDBY]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Putting toolhead T{toolhead} into standby mode."
	DEBUG_ECHO PREFIX="_TOOLHEAD_STANDBY" MSG="toolhead: {toolhead}, config_z_hop: {config_z_hop}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={toolhead} SYNC=0
	PARK_TOOLHEAD
	
	
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={toolchange_standby_temp}
	{% endif %}
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=True
	{% endif %}
	
	
	_LED_TOOLHEAD_STANDBY TOOLHEAD={toolhead}

[gcode_macro _TOOLHEAD_WAKEUP]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set fan_speed = params.FAN_SPEED|float %}
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift_count = params.TOOLSHIFT_COUNT|default(0)|int %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% if toolshift_count == 1 %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% endif %}
	{% set needs_wakeup = true if printer["gcode_macro T%s" % toolhead].standby|default(false)|lower == 'true' else false %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Waking up toolhead T{toolhead}. Please wait for extruder to heat up..."
	DEBUG_ECHO PREFIX="_TOOLHEAD_WAKEUP" MSG="toolhead: {toolhead}, fan_speed: {fan_speed}, new_x: {new_x}, new_y: {new_y}, new_z: {new_z}, config_z_hop: {config_z_hop}"
	
	
	_LED_TOOLHEAD_WAKEUP TOOLHEAD={toolhead}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={toolhead} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE=1
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if toolhead == 0 else toolhead}
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if needs_wakeup %}
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set temp = extruder_first_layer_temp[toolhead]|float %}
	{% else %}
	{% set temp = extruder_other_layer_temp[toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if toolhead == 0 else 'extruder1'} MINIMUM={temp}  MAXIMUM={temp + 5}
	{% endif %}
	
	
	_LED_PRINTING TOOLHEAD={toolhead}
	
	
	{% if purge > 0 %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={toolhead} E={purge}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	
	
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if toolhead == 1 else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	G92 E0
	G1 E-{e} F{feedrate}
	G92 E0
	
	
	{% if new_x >= 0 and new_y >= 0 %}
	G1 X{new_x} Y{new_y} F{speed}
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={config_z_hop} T={toolhead} SYNC=0
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=False

[gcode_macro _TOOLCHANGE]
variable_toolshift_count = 0
gcode = 
	
	
	{% set new_t = params.T|default(-1)|int %}
	{% set new_x = params.X|default(-1.0)|float %}
	{% set new_y = params.Y|default(-1.0)|float %}
	{% set new_z = params.Z|default(-1.0)|float %}
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(true)|lower == 'true' else false %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T: {new_t}, X: {new_x}, Y: {new_y}, Z: {new_z}, PARK_T0: {park_t0}, PARK_T1: {park_t1}, IS_PRINTING_GCODE: {is_printing_gcode}, TOOLSHIFT: {toolshift}"
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	{% if park_t0 >= 0 and park_t1 >= 0 %}
	{% set parking_position_t0 = park_t0 %}
	{% set parking_position_t1 = park_t1 %}
	{% set parking_position_act_t = park_t0 if act_t == 0 else park_t1 %}
	{% endif %}
	
	
	{% if not is_printing_gcode and not toolshift %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Changing tool to T{new_t} without retracting/extruding or moving the toolheads except for parking."
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	G90
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% if not is_printing_gcode and toolshift and new_x < 0 and new_y < 0 %}
	{% set new_x = center_x %}
	{% set new_y = printer.gcode_move.gcode_position.y|float %}
	{% endif %}
	
	{% if new_x < 0 or new_y < 0 %}
	
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="No new X or Y position given, parking the active toolhead and activating the new toolhead without moving it."
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={new_t}
	
	
	{% if "x" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	{% if is_printing_gcode %}
	_EXTRUDE T={new_t}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	{% if "xyz" not in printer.toolhead.homed_axes %}
	
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	
	
	{% set svv = printer.save_variables.variables %}
	{% if new_t == default_toolhead %}
	{% set new_xoffset = 0 %}
	{% set new_yoffset = 0 %}
	{% set new_zoffset = 0 %}
	{% else %}
	{% set new_xoffset = -svv.idex_xoffset %}
	{% set new_yoffset = -svv.idex_yoffset %}
	{% set new_zoffset = -svv.idex_zoffset %}
	{% endif %}
	
	{% set xoffset_correction = new_xoffset - printer.named_offsets.toolhead_alignment.x %}
	{% set yoffset_correction = new_yoffset - printer.named_offsets.toolhead_alignment.y %}
	{% set zoffset_correction = new_zoffset - printer.named_offsets.toolhead_alignment.z %}
	
	{% if new_t == 0 %}
	
	{% set t0_act_x = parking_position_t0 %}
	{% set t1_act_x = printer.toolhead.position.x|float %}
	{% set t0_new_x = new_x %}
	{% set t1_new_x = parking_position_t1 %}
	{% set t0_distance = t0_new_x - t0_act_x %}
	{% set t1_distance = t1_new_x - t1_act_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T0."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	
	
	G1 X{t0_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x + (t1_new_x - t1_act_x)} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t0_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T0: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% elif new_t == 1 %}
	
	{% set t0_act_x = printer.toolhead.position.x|float %}
	{% set t1_act_x = parking_position_t1 %}
	{% set t0_new_x = parking_position_t0 %}
	{% set t1_new_x = new_x %}
	{% set t0_distance = t0_act_x - t0_new_x %}
	{% set t1_distance = t1_act_x - t1_new_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T1."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x - t1_distance + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t1_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T1: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% endif %}
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	{% endif %}

[gcode_macro _ZHOP_BEFORE_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_hop = params.Z_HOP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_HOP: {z_hop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="COMBINED_ZHOP G1 Z+{z_hop} E-{e} F{speed * 60}"
	G1 Z+{z_hop} E-{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="ZHOP G1 Z+{z_hop} F{speed * 60}"
	G1 Z+{z_hop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="RETRACT G1 E-{e} F{feedrate}"
	G1 E-{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _ZDROP_AFTER_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_drop = params.Z_DROP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_DROP: {z_drop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="COMBINED_ZDROP G1 Z-{z_drop} E{e} F{speed * 60}"
	G1 Z-{z_drop} E{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="ZDROP G1 Z-{z_drop} F{speed * 60}"
	G1 Z-{z_drop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="EXTRUDE G1 E{e} F{feedrate}"
	G1 E{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _EXTRUDE]
gcode = 
	
	{% set t = params.T|int %}
	
	
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	
	DEBUG_ECHO PREFIX="_EXTRUDE" MSG="G1 E{e} F{feedrate * 60}"
	
	
	G91
	M82
	G92 E0
	G1 E{e} F{feedrate * 60}
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _DEACTIVATE_TOOLHEAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_DEACTIVATE_TOOLHEAD" MSG="TOOLHEAD {toolhead}"
	
	
	{% if toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% endif %}
	
	
	M106.1 S0
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={toolhead}

[delayed_gcode _INIT_TOOLHEADS]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	_IDEX_SINGLE INIT=1
	
	
	{% if printer.fastconfig.settings.dual_carriage.safe_distance is defined %}
	{% if printer.fastconfig.settings.dual_carriage.safe_distance|float < 50 %}
	{ action_emergency_stop("Dual carriage safe_distance seems to be too low!") }
	{% endif %}
	{% else %}
	{ action_emergency_stop("Dual carriage safe_distance not defined!") }
	{% endif %}

[gcode_macro _SET_TOOLHEAD_OFFSET]
description = "Internal use only. Sets the toolhead_alignment offset (and hotend_thermal_expansion offset when configured) for the active/dominant toolhead."
gcode = 
	
	{% set move = params.MOVE|default(0)|int %}
	{% set force_toolhead = params.FORCE_TOOLHEAD|default(-1)|int %}
	
	
	{% if params.T is defined %}
	CONSOLE_ECHO TYPE="error" MSG="_SET_TOOLHEAD_OFFSET called with deprectated T parameter, which is ignored."
	{';$_SET_TOOLHEAD_OFFSET_ignoring_TOOLHEAD_parameter'}
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="active/dominant toolhead: {toolhead}, MOVE: {move}, FORCE_TOOLHEAD: {force_toolhead}"
	
	
	{% if force_toolhead >= 0 %}
	{% set toolhead = force_toolhead %}
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="FORCE_TOOLHEAD applied, using TOOLHEAD: {toolhead}"
	{% endif %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set move = 0 %}
	{% endif %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|int %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X=0 Y=0 MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z=0 MOVE={move} SPEED={z_speed}
	{% else %}
	{% set svv = printer.save_variables.variables %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X={(-svv.idex_xoffset)} Y={(-svv.idex_yoffset)} MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-svv.idex_zoffset)} MOVE={move} SPEED={z_speed}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}

[gcode_macro TOOLSHIFT_CONFIG]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={params.SPEED|default(300)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={params.ACCEL|default(5000)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_retraction VALUE={params.RETRACT|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_extrusion VALUE={params.EXTRUDE|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_feedrate VALUE={params.FEEDRATE|default(7200)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={params.Z_HOP|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zspeed VALUE={params.Z_SPEED|default(25)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_combined_zhop VALUE={true if params.COMBINED_ZHOP|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_sync_fans VALUE={true if params.SYNC_FANS|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_prepurging_timer VALUE={params.AUTO_PURGE_TIME|default(0)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_purge VALUE={params.PURGE|default(25)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_standby_temp VALUE={params.STANDBY_TEMP|default(-1)|float}

[gcode_macro CALCULATE_DC_ENDSTOP]
description = "DEPRECATED: This macro has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."
gcode = 
	CONSOLE_ECHO TITLE="CALCULATE_DC_ENDSTOP has been deprecated" TYPE="error" MSG="The CALCULATE_DC_ENDSTOP has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."

[gcode_macro _VAOC]
variable_is_fixed = True
variable_is_started = False
variable_is_started_at_temp = False
variable_additional_safe_distance = 50
variable_safe_z = 30
variable_auto_z_offset_calibration = True
variable_enable_camera_cooling = True
variable_camera_cooling_fan_speed = 0.3
variable_camera_cooling_temperature = 50
variable_toolchange_travel_speed = 300
variable_toolchange_travel_accel = 5000
variable_adjusting_secondary_toolhead_focus_adjusts_zoffset = False
variable_cache_toolchange_travel_speed = 300
variable_cache_toolchange_travel_accel = 5000
variable_cache_toolchange_zhop = 1.0
variable_t0_toolhead_sensor_enabled = 0
variable_t1_toolhead_sensor_enabled = 0
variable_t0_bowden_sensor_enabled = 0
variable_t1_bowden_sensor_enabled = 0
variable_loaded_skew_profile = ""
variable_gcode_z_offset = 0.0
variable_start_x_offset = 0.0
variable_start_y_offset = 0.0
gcode = 
	_ECHO_VAOC_VARS
variable_expected_camera_x_position = 212.5
variable_expected_camera_y_position = 530.5

[gcode_macro _VAOC_START]
description = Called from the front end. If T0_TEMP, T1_TEMP and BED_TEMP parameter are specified, VAOC calibration will start under real conditions at printing temp.
gcode = 
	
	{% set t0_temp = params.T0_TEMP|default(0)|int %}
	{% set t1_temp = params.T1_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(0)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro SKEW_PROFILE"].loaded_profile|default("") %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=loaded_skew_profile VALUE='"{loaded_skew_profile}"'
	
	
	{% if t0_temp > 0 and t1_temp > 0 and bed_temp > 0 %}
	
	
	{% if not is_fixed %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("VAOC calibration at temp works only with a fixed installed VAOC device.") }
	{% endif %}
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE=0
	{% endif %}
	
	
	START_PRINT EXTRUDER_TEMP={t0_temp},{t1_temp} EXTRUDER_OTHER_LAYER_TEMP={t0_temp},{t1_temp} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp} INITIAL_TOOL=0 TOTAL_LAYER_COUNT=1 X0={(printable_x_max / 2 - 10)} Y0={(printable_y_max / 2 - 10)} X1={(printable_x_max / 2 + 10)} Y1={(printable_y_max / 2 + 10)} TOTAL_TOOLSHIFTS=1 FIRST_X={printable_x_max / 2} FIRST_Y={printable_y_max / 2} MIN_X={(printable_x_max / 2 - 10)} MAX_X={(printable_x_max / 2 + 10)} USED_TOOLS=0,1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=True
	
	{% endif %}
	
	
	_START_VAOC

[gcode_macro _START_VAOC]
description = Called from _VAOC_START. Do not call it manually.
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(printable_x_max/2)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(printable_y_max/2)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	DEBUG_ECHO PREFIX="VAOC_START" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, zcontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_x_offset VALUE={svv.idex_xoffset|default(0.0)|float}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_y_offset VALUE={svv.idex_yoffset|default(0.0)|float}
	
	
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_SAFE_Z_HEIGHT
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_speed VALUE={printer["gcode_macro RatOS"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_accel VALUE={printer["gcode_macro RatOS"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_zhop VALUE={printer["gcode_macro RatOS"].toolchange_zhop|float}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE=0
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"START X_REFERENCE:%.6f Y_REFERENCE:%.6f Z_REFERENCE:%.6f PARK_T0:%.6f PARK_T1:%.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, parking_position_t0, parking_position_t1)}
	
	
	_LED_VAOC_ON
	
	
	
	
	
	
	
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=gcode_z_offset VALUE={printer.gcode_move.homing_origin.z}
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z=0
	
	
	MAYBE_HOME
	M400
	
	
	_LOAD_RATOS_SKEW_PROFILE
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	IDEX_SINGLE
	{% endif %}
	
	
	
	SAVE_GCODE_STATE NAME=vaoc_state
	
	
	RESET_NAMED_OFFSET EVENT=reset_all
	
	
	{% if is_fixed %}
	_SELECT_TOOL T=0 TOOLSHIFT=false
	{% if default_toolhead == 0 %}
	G1 X{idex_xcontrolpoint} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint + safe_distance + additional_safe_distance} F{speed}
	{% else %}
	G1 X{idex_xcontrolpoint - safe_distance - additional_safe_distance} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint} F{speed}
	{% endif %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	{% else %}
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	G1 X{idex_xcontrolpoint} F{speed}
	G1 Y{idex_ycontrolpoint} F{speed}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	
	
	_SELECT_TOOL T={default_toolhead} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	{% if not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={default_toolhead}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=True

[gcode_macro _VAOC_END]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_y = printable_y_max / 2 %}
	{% set saved_gcode_z_offset = printer["gcode_macro _VAOC"].gcode_z_offset|default(0.0)|float %}
	
	DEBUG_ECHO PREFIX="_VAOC_END" MSG="printable_y_max: {printable_y_max}, center_y: {center_y}, safe_z: {safe_z}"
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% set x_offset_change = svv.idex_xoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_x_offset|default(0.0)|float %}
	{% set y_offset_change = svv.idex_yoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_y_offset|default(0.0)|float %}
	{% set offset_change_norm = (x_offset_change ** 2 + y_offset_change ** 2) ** 0.5 %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="VAOC calibration changed the relative XY offset between T0 and T1 by {offset_change_norm|round(3)} mm (ΔX: {x_offset_change|round(3)}, ΔY: {y_offset_change|round(3)})"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	G1 Y{center_y} F{speed}
	
	
	_IDEX_SINGLE INIT=1
	
	
	_LED_VAOC_OFF
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={printer["gcode_macro _VAOC"].cache_toolchange_zhop|float}
	
	
	{% if printer["gcode_macro _VAOC"].is_started_at_temp|default(true)|lower == 'true' %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_bowden_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_bowden_sensor_enabled|int}
	{% endif %}
	{% endif %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro _VAOC"].loaded_skew_profile|default("") %}
	{% if loaded_skew_profile != "" %}
	SKEW_PROFILE LOAD={loaded_skew_profile}
	{% else %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=vaoc_state
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z={saved_gcode_z_offset}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False

[gcode_macro _VAOC_LOAD_TOOL]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set auto_temp_offset = true if params.AUTO_TEMP_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set toolhead_zoffset = svv.idex_zoffset|default(0)|float %}
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move T%s to control point: X%.6f Y%.6f Z%.6f IS_FIXED=%s"' % (t, idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, is_fixed)}
	
	
	{% if not auto_temp_offset and not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={t}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	{% set current_z = printer.toolhead.position.z|float %}
	{% set lowest_toolhead_z = [current_z, current_z - toolhead_zoffset]|min %}
	{% if lowest_toolhead_z < safe_z %}
	G1 Z{[safe_z, safe_z + toolhead_zoffset]|max} F{z_speed}
	{% else %}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	{% endif %}
	
	
	_SELECT_TOOL T={t} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_SET_CAMERA_COOLING]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	
	
	{% set enable_camera_cooling = true if printer["gcode_macro _VAOC"].enable_camera_cooling|default(true)|lower == 'true' else false %}
	{% set camera_cooling_temperature = printer["gcode_macro _VAOC"].camera_cooling_temperature|float %}
	{% set camera_cooling_fan_speed = printer["gcode_macro _VAOC"].camera_cooling_fan_speed|float %}
	
	
	{% if printer.heater_bed.temperature >= camera_cooling_temperature and enable_camera_cooling %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={camera_cooling_fan_speed if t == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={camera_cooling_fan_speed if t == 1 else 0}
	
	
	M106.1 S{camera_cooling_fan_speed}
	
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	{% endif %}

[gcode_macro _VAOC_SET_TOOL]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="_VAOC_SET_TOOL" MSG="IDEX_MODE: {idex_mode}, TOOLHEAD: {toolhead}"
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	{% set x = printer.gcode_move.gcode_position.x|float %}
	{% set y = printer.gcode_move.gcode_position.y|float %}
	{% set z = printer.gcode_move.gcode_position.z|float %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE={x}
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE={y}
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE={z}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Control point was set: X%.6f Y%.6f Z%.6f"' % (x, y, z)}
	
	{% else %}
	
	
	
	{% set move_diff_x = printer.gcode_move.gcode_position.x|float - svv.idex_xcontrolpoint|float %}
	{% set move_diff_y = printer.gcode_move.gcode_position.y|float - svv.idex_ycontrolpoint|float %}
	{% set move_diff_z = printer.gcode_move.gcode_position.z|float - svv.idex_zcontrolpoint|float %}
	
	
	{% set new_x_offset = svv.idex_xoffset - move_diff_x %}
	{% set new_y_offset = svv.idex_yoffset - move_diff_y %}
	{% set new_z_offset = svv.idex_zoffset - move_diff_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE={new_x_offset}
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE={new_y_offset}
	
	{% set z_focus_msg = "" %}
	{% if move_diff_z|abs > 1e-6 %}
	{% if printer["gcode_macro _VAOC"].adjusting_secondary_toolhead_focus_adjusts_zoffset|default(false)|lower == 'true' %}
	{% set z_focus_msg = " (Z offset adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={new_z_offset}
	{% else %}
	{% set z_focus_msg = " (Z offset not adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	{% set new_z_offset = svv.idex_zoffset %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset was set: X%.6f Y%.6f Z%.6f%s"' % (toolhead, new_x_offset, new_y_offset, new_z_offset, z_focus_msg)}
	
	{% endif %}

[gcode_macro _VAOC_MOVE]
gcode = 
	
	{% set x = params.X|default(0)|float %}
	{% set y = params.Y|default(0)|float %}
	{% set z = params.Z|default(0)|float %}
	
	
	G91
	{% if z != 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 Z%.6f F300"' % (z)}
	G1 Z{z} F300
	
	{% else %}
	{% if x <=2 and y <=2 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 X%.6f Y%.6f F18000"' % (x, y)}
	G1 X{x} Y{y} F18000
	{% endif %}
	{% endif %}
	G90

[gcode_macro _VAOC_CALIBRATE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	{% if printer["z_offset_probe"] is defined and is_started %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	
	{% if auto_z_offset %}
	_START_VAOC AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_END
	{% else %}
	_VAOC_LOAD_TOOL T={default_toolhead}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	{% endif %}
	
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_Z_OFFSET
	
	{% endif %}

[gcode_macro _VAOC_PROBE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}
	{% if not auto_z_offset %}
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	{% endif %}
	M400
	_VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT

[gcode_macro _VAOC_Z_OFFSET_PROBE_CURRENT_POSITION]
gcode = 
	
	Z_OFFSET_PROBE PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_DROP=1 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median

[gcode_macro _VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT]
gcode = 
	{% if printer["z_offset_probe"] is defined %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE={last_z}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Z-offset control point set:: %.6f"' % last_z}
	
	{% else %}
	
	
	
	{% set z = svv.idex_zoffsetcontrolpoint|float - last_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={z}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-z)}
	
	
	G0 Z{svv.idex_zcontrolpoint|float} F{z_speed}
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset set: Z %.6f"' % (t, z)}
	
	{% endif %}
	
	{% endif %}

[gcode_macro _VAOC_ECHO_Z_OFFSET]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s toolhead z-offset %.6f"' % (1 if default_toolhead == 0 else 0, svv.idex_zoffset)}
	{% if svv.idex_zoffset|abs < 0.02 %}
	CONSOLE_ECHO TITLE={'"Perfect toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="You have a perfect toolhead z-offset!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.02 and svv.idex_zoffset|abs < 0.05 %}
	CONSOLE_ECHO TITLE={'"Good toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is good!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.05 and svv.idex_zoffset|abs < 0.1 %}
	CONSOLE_ECHO TITLE={'"High toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset could be better._N_Use minimum 0.3mm first layer height for copy and mirror mode prints." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.1 and svv.idex_zoffset|abs < 0.2 %}
	CONSOLE_ECHO TITLE={'"Bad toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is bad._N_Copy and mirror mode prints are not recommended with it." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.2 %}
	CONSOLE_ECHO TITLE={'"Unacceptable toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is unacceptable._N_Do not print in copy and mirror mode with it." TYPE="alert"
	{% endif %}
	RATOS_ECHO PREFIX="VAOC" MSG="Toolhead z-offset calibration done!"

[gcode_macro _VAOC_CALIBRATE_TEMP_OFFSET]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if is_fixed and is_started and printer["z_offset_probe"] is defined and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	_VAOC_LOAD_TOOL T={default_toolhead} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_NOZZLE_TEMP_OFFSETS
	
	{% endif %}

[gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET=0
	
	
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	M400

[gcode_macro _VAOC_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(150)|float %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Probing with nozzle temperature {temp}°C..."
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	
	
	G0 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _VAOC_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set msg = '"T0 expansion coefficient %.6fmm_N_T1 expansion coefficient %.6fmm"' % (svv.nozzle_expansion_coefficient_t0, svv.nozzle_expansion_coefficient_t1) %}
	CONSOLE_ECHO TITLE="Nozzle expansion coefficients:" MSG={msg} TYPE="success"

[gcode_macro _VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - expected_camera_x_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC x-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_xcontrolpoint, expected_camera_x_position)) }
	{% endif %}
	{% if (idex_ycontrolpoint - expected_camera_y_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC y-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_ycontrolpoint, expected_camera_y_position)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - printer.gcode_move.gcode_position.x|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected y-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_xcontrolpoint, printer.gcode_move.gcode_position.x|float)) }
	{% endif %}
	{% if (idex_ycontrolpoint - printer.gcode_move.gcode_position.y|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected x-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_ycontrolpoint, printer.gcode_move.gcode_position.y|float)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_SAFE_Z_HEIGHT]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set idex_zoffsetcontrolpoint = svv.idex_zoffsetcontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_SAFE_Z_HEIGHT" MSG={'"idex_zcontrolpoint: %.6f, idex_zoffsetcontrolpoint: %.6f"' % (idex_zcontrolpoint, idex_zoffsetcontrolpoint)}
	
	{% if safe_z < idex_zcontrolpoint + 2 or safe_z < idex_zoffsetcontrolpoint + 2 %}
	{action_raise_error("VAOC safe_z value (%.3f) is too low, it must be higher than %.3f" % (safe_z, [idex_zoffsetcontrolpoint + 2, idex_zcontrolpoint + 2]|max))}
	{% endif %}

[gcode_macro _VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED]
gcode = 
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T0. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T1. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_RESET]
gcode = 
	DEBUG_ECHO PREFIX="_VAOC_RESET" MSG="running template-emitted _VAOC_RESET macro"
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE=212.5
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE=530.5
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE=10
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE=0
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE=0.0
	
	RESET_DC_ENDSTOP_CONFIGURATION
	RESET_Y_MAX_ADJUSTMENT
	
	
	CONSOLE_ECHO TITLE="VAOC Configuration Reset" MSG="VAOC configuration has been reset. You must RESTART klipper for the changes to take effect,_N_then re-calibrate VAOC."

[gcode_macro _ECHO_VAOC_VARS]
description = Echo VAOC variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro _VAOC"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro _VAOC_SWITCH_LED]
gcode = 
	{% if params.STATE|default(0)|int == 1 %}
	_LED_VAOC_ON
	{% else %}
	_LED_VAOC_OFF
	{% endif %}

[gcode_macro Z_PROBE_TEST_T0]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T0
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST_T1]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T1
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	
	
	_VAOC_Z_PROBE_TEST_EVALUATE
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro _VAOC_Z_PROBE_LOOP]
gcode = 
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_SHAKE_IT
	_VAOC_START

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if primary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T0. Retried {primary_retries} time(s)."
	{% endif %}
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	
	{% if (primary_range - secondary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 is drifting significantly more than T1."
	{% endif %}
	{% if (secondary_range - primary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 is drifting significantly more than T0."
	{% endif %}
	
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T0]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T1]
gcode = 
	
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _SHAKE_IT]
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	_Z_HOP
	{% for i in range(3) %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 + 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 + 1}
	{% endfor %}
	{% for i in range(2) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 + 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 + 50}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 1}
	{% endfor %}
	{% endfor %}

[gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 retries updated: {new_retries}"

[gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 retries updated: {new_retries}"

[gcode_macro _CLEAR_PRIMARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _CLEAR_SECONDARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _VAOC_TEST_Z_OFFSET]
gcode = 
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}

[delayed_gcode _IDEX_INIT]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	VERIFY_HYBRID_INVERTED

[gcode_macro Z_TILT_ADJUST]
rename_existing = Z_TILT_ADJUST_ORIG
gcode = 
	
	{% set beacon_contact_z_tilt_adjust_samples = printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust_samples|default(2)|int %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(true)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	_IDEX_SINGLE
	
	_SELECT_TOOL T={printer["gcode_macro RatOS"].default_toolhead|default(0)|int} TOOLSHIFT=false
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_tilt_adjust %}
	Z_TILT_ADJUST_ORIG PROBE_METHOD=contact SAMPLES={beacon_contact_z_tilt_adjust_samples}
	{% else %}
	Z_TILT_ADJUST_ORIG
	{% endif %}
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if idex_mode == "copy" %}
	_IDEX_COPY
	{% elif idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[stepper_x]
position_max = 500
position_endstop = -59.6
position_min = -59.6
step_pin = PF13
dir_pin = x_dir_pin
enable_pin = !PF14
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t0:PA2

[stepper_y]
position_max = 533.65
position_min = -14.35
position_endstop = -14.35
step_pin = PG0
dir_pin = !y_dir_pin
enable_pin = !PF15
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = PG9

[stepper_z]
position_max = 500
position_min = -7
step_pin = PC13
dir_pin = !z0_dir_pin
enable_pin = !PF1
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4
homing_speed = 10
endstop_pin = probe:z_virtual_endstop

[z_tilt]
z_positions = 
	0,0
	250,500
	500,0
points = 
	20, 10
	480, 230
	20, 450
horizontal_move_z = 20
retries = 10
retry_tolerance = 0.02
speed = 600

[extruder]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t0:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t0:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t0:PD3
dir_pin = toolboard_t0:e_dir_pin
enable_pin = !toolboard_t0:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[firmware_retraction]
retract_speed = 60
unretract_extra_length = 0
unretract_speed = 60
retract_length = 0.2

[extruder1]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t1:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t1:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t1:PD3
dir_pin = toolboard_t1:e_dir_pin
enable_pin = !toolboard_t1:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[resonance_tester]
accel_chip_x = lis2dw toolboard_t0
accel_chip_y = lis2dw toolboard_t0
probe_points = 
	250,250,20

[tmc5160 stepper_x]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC4
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 dual_carriage]
stealthchop_threshold = 0
interpolate = True
cs_pin = PF2
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y]
stealthchop_threshold = 0
interpolate = True
cs_pin = PD11
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y1]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC7
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[stepper_y1]
step_pin = PG4
dir_pin = y1_dir_pin
enable_pin = !PA2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46

[tmc2209 stepper_z]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE4
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[tmc2209 stepper_z1]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE1
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z1]
step_pin = PE2
dir_pin = !z1_dir_pin
enable_pin = !PD4
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 stepper_z2]
stealthchop_threshold = 0
interpolate = True
uart_pin = PD3
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z2]
step_pin = PE6
dir_pin = !z2_dir_pin
enable_pin = !PE0
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 extruder]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t0:PB3
run_current = 0.707
sense_resistor = 0.11

[tmc2209 extruder1]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t1:PB3
run_current = 0.707
sense_resistor = 0.11

[beacon]
serial = /dev/beacon
x_offset = 0
y_offset = 27.5
mesh_main_direction = x
mesh_runs = 1
mesh_cluster_size = 0
speed = 15.
lift_speed = 80.
contact_max_hotend_temperature = 275
contact_mesh_min = 20,20
contact_mesh_max = 480,480

[beacon_user_z_offset]

[beacon_mesh]

[beacon_true_zero_correction]

[beacon_adaptive_heat_soak]

[delayed_gcode _BEACON_INIT]
initial_duration = 1
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	_BEACON_MESH_INIT
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_coefficient_multiplier
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_applied_offset
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=beacon_saved_runtime_offset
	{% if printer["gcode_macro RatOS"].beacon_contact_expansion_multiplier is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_contact_expansion_multiplier is no longer used, please remove it from your config file."
	{% endif %}
	{% if printer["gcode_macro RatOS"].beacon_scan_compensation_resolution is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_scan_compensation_resolution is no longer used, please remove it from your config file."
	{% endif %}

[gcode_macro BEACON_RATOS_CALIBRATION]
gcode = 
	RATOS_ECHO MSG="Did you mean BEACON_RATOS_CALIBRATE?"

[gcode_macro BEACON_RATOS_CALIBRATE]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	BEACON_INITIAL_CALIBRATION _AUTOMATED=True
	
	{% if beacon_contact_start_print_true_zero %}
	BEACON_POKE_TEST _AUTOMATED=True
	_BEACON_CHECK_POKE
	{% if printer["dual_carriage"] is not defined %}
	BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET _AUTOMATED=True
	{% endif %}
	{% endif %}
	
	{% set already_heated = False %}
	
	
	{% if beacon_contact_start_print_true_zero and beacon_scan_compensation_enable %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% set already_heated = True %}
	{% endif %}
	
	
	BEACON_FINAL_CALIBRATION _AUTOMATED=True _AUTOMATED_ALREADY_HEATED={already_heated} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	{% if beacon_contact_start_print_true_zero %}
	{% if printer["dual_carriage"] is not defined %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	_BEACON_ECHO_POKE
	{% endif %}
	RATOS_ECHO MSG="Beacon calibration finished!"
	
	
	_LED_BEACON_CALIBRATION_END
	
	
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG

[gcode_macro BEACON_INITIAL_CALIBRATION]
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Initial beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro BEACON_FINAL_CALIBRATION]
description = Runs BEACON_AUTO_CALIBRATE after heating the bed and chamber to specified temperatures. This creates a beacon model under reference conditions for future use.
	This macro will skip calibration if both the beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero settings are enabled, because a new
	model will be calibrated automatically at the start of each print. Use FORCE=True to override this check.
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set already_heated = true if params._AUTOMATED_ALREADY_HEATED|default(false)|lower == 'true' else false %}
	{% set force = params.FORCE|default('false')|lower in ('1', 'true', 'yes') %}
	
	
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default('false')|lower == "true" %}
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero and not force %}
	RATOS_ECHO MSG="BEACON_FINAL_CALIBRATION skipped, not needed because beacon_contact_calibrate_model_on_true_zero is enabled. Use FORCE=True to override."
	{% else %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	{% if chamber_temp > 0 and not already_heated %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	{% if not already_heated %}
	
	G0 Z2.5 F{z_hop_speed}
	
	
	RATOS_ECHO MSG="Waiting for calibration temperature..."
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	{% if beacon_adaptive_heat_soak %}
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,3600]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_Z_HOP
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Final beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	{% endif %}

[gcode_macro BEACON_POKE_TEST]
variable_poke_result_1 = -1
variable_poke_result_2 = -1
variable_poke_result_3 = -1
variable_poke_result_4 = -1
variable_poke_result_5 = -1
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_1 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_2 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_3 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_4 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_5 VALUE=-1
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G0 Z5 F{z_hop_speed}
	
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=1
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=2
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=3
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=4
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=5
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Beacon poke test finished!"
	{% if not automated %}
	_BEACON_ECHO_POKE
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro _BEACON_PROBE_POKE]
gcode = 
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	BEACON_POKE speed=3 top=5 bottom={poke_bottom}
	BEACON_QUERY

[gcode_macro _BEACON_STORE_POKE]
gcode = 
	
	{% set i = params.I|default(1)|int %}
	
	
	{% set last_z = printer.beacon.last_poke_result|default(0)|float %}
	
	
	{% if printer.beacon.last_poke_result|lower != "none" %}
	{% if printer.beacon.last_poke_result.error == 0 %}
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE={"poke_result_%s" % i} VALUE={printer.beacon.last_poke_result.latency}
	{% endif %}
	{% endif %}

[gcode_macro _BEACON_CHECK_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% if p1 == -1 or p2 == -1 or p3 == -1 or p4 == -1 or p5 == -1 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test error!") }
	{% endif %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	{% if avg > 6 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test failed!") }
	{% endif %}

[gcode_macro _BEACON_ECHO_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	
	
	{% if avg <= 1 %}
	{% set type = "success" %}
	{% set note = "Extremely low noise, rarely achieved" %}
	{% elif avg > 1 and avg <= 4 %}
	{% set type = "info" %}
	{% set note = "Excellent performance for a typical printer" %}
	{% elif avg > 4 and avg <= 8 %}
	{% set type = "warning" %}
	{% set note = "Acceptable performance, machine may have considerable cyclic axis noise" %}
	{% elif avg > 8 and avg <= 11 %}
	{% set type = "alert" %}
	{% set note = "Not ideal, may want to verify proper mounting or use thinner stackups" %}
	{% elif avg > 11 %}
	{% set type = "alert" %}
	{% set note = "Reason for concern, present setup may be risky to continue with" %}
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon poke test result:" TYPE={type} MSG={'"Average latency: %.2f_N_%s"' % (avg, note)}

[gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Nozzle temperature offset calibration..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET=0
	
	
	{% if not automated %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing with nozzle temperature {temp}°C..."
	PROBE PROBE_METHOD=contact PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median
	BEACON_QUERY
	
	
	G0 Z5 F{z_speed}

[gcode_macro _BEACON_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer.beacon.last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{default_toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% if default_toolhead == 0 %}
	CONSOLE_ECHO TYPE="info" MSG={'"T0 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t0}
	{% else %}
	CONSOLE_ECHO TYPE="info" MSG={'"T1 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t1}
	{% endif %}

[gcode_macro _BEACON_SET_NOZZLE_TEMP_OFFSET]
description = "Set the thermal expansion z offset for the active toolhead based on the current extruder target temperature and thermal expansion coefficient."
gcode = 
	{% if params.RESET is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The RESET parameter is no longer supported and has no effect."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% if params.TOOLHEAD is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The TOOLHEAD parameter is no longer supported and has no effect. The macro now automatically determines the current toolhead."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	{% if beacon_contact_expansion_compensation %}
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set nozzle_expansion_coefficient_t0 = svv.nozzle_expansion_coefficient_t0|default(0)|float %}
	{% if printer["dual_carriage"] is defined %}
	{% set nozzle_expansion_coefficient_t1 = svv.nozzle_expansion_coefficient_t1|default(0)|float %}
	{% endif %}
	
	
	{% set temp = printer['extruder' if toolhead == 0 else 'extruder1'].target|float %}
	
	
	{% set temp_delta = temp - beacon_contact_true_zero_temp %}
	{% set expansion_coefficient = nozzle_expansion_coefficient_t0 if toolhead == 0 else nozzle_expansion_coefficient_t1 %}
	{% set expansion_offset = temp_delta * (expansion_coefficient / 100) %}
	
	
	SET_NAMED_OFFSET NAME=hotend_thermal_expansion Z={expansion_offset} MOVE=1 MOVE_SPEED={z_speed}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG={'"Nozzle expansion offset of %.6fmm applied to T%s"' % (expansion_offset, toolhead)}
	DEBUG_ECHO PREFIX="_BEACON_SET_NOZZLE_TEMP_OFFSET" MSG="toolhead: {toolhead}, coefficient: {expansion_coefficient|round(6)}, temp_delta: {temp_delta|round(1)},  expansion_offset: {expansion_offset|round(6)}"
	
	{% endif %}

[gcode_macro BEACON_MEASURE_BEACON_OFFSET]
variable_needs_compensation = False
variable_reference_z = 0.0
variable_front = 0.0
variable_front_left = 0.0
variable_front_right = 0.0
variable_back = 0.0
variable_back_left = 0.0
variable_back_right = 0.0
variable_right = 0.0
variable_left = 0.0
variable_margin_x = 40
variable_margin_y = 40
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=False
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Measure beacon offset..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="center"
	
	
	G0 X{margin_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_left"
	
	
	G0 X{safe_home_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front"
	
	
	G0 X{(printable_x_max - margin_x)} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_right"
	
	
	G0 X{safe_home_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back"
	
	
	G0 X{margin_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_left"
	
	
	G0 X{margin_x} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="left"
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_BEACON_ECHO_BEACON_OFFSET
	
	
	_LED_BEACON_CALIBRATION_END
	
	{% endif %}

[gcode_macro _BEACON_STORE_BEACON_OFFSET]
gcode = 
	
	{% set location = params.LOCATION|lower %}
	
	
	{% set last_z = printer.beacon.last_offset_result["delta"]|default(0)|float %}
	
	
	{% if location == "center" %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE={location} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_BEACON_OFFSET]
gcode = 
	
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float * 1000 %}
	{% set front_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_left|default(0)|float * 1000 %}
	{% set front = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front|default(0)|float * 1000 %}
	{% set front_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_right|default(0)|float * 1000 %}
	{% set right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].right|default(0)|float * 1000 %}
	{% set back_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_right|default(0)|float * 1000 %}
	{% set back = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back|default(0)|float * 1000 %}
	{% set back_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_left|default(0)|float * 1000 %}
	{% set left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].left|default(0)|float * 1000 %}
	
	{% set line_1 = "Front left:    %.6fμm" % (front_left) %}
	{% set line_2 = "Front center:  %.6fμm" % (front) %}
	{% set line_3 = "Front right:   %.6fμm" % (front_right) %}
	{% set line_4 = "Left center:   %.6fμm" % (left) %}
	{% set line_5 = "Right center:  %.6fμm" % (right) %}
	{% set line_6 = "Back left:     %.6fμm" % (back_left) %}
	{% set line_7 = "Back center:   %.6fμm" % (back) %}
	{% set line_8 = "Back right:    %.6fμm" % (back_right) %}
	
	{% set max_value = [(front_left|abs), (front|abs), (front_right|abs), (left|abs), (right|abs), (back_left|abs), (back|abs), (back_right|abs)]|max %}
	{% if max_value <= 50 %}
	{% set type = "success" %}
	{% set recommendation = "Very low beacon offset: %.6fμm._N_No beacon scan compensation needed." % max_value %}
	{% elif max_value > 50 and max_value <= 100 %}
	{% set type = "info" %}
	{% set recommendation = "Low beacon offset: %.6fμm._N_You may experience first layer inconsistensies, consider beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 100 and max_value <= 150 %}
	{% set type = "warning" %}
	{% set recommendation = "High beacon offset: %.6fμm._N_High chance of first layer problems, beacon scan compensation is highly encouraged." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 150 and max_value <= 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Very High beacon offset: %.6fμm._N_You will encounter first layer problems on large prints unless you activate beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Extremely high beacon offset: %.6fμm._N_You have significant scan/contact inconsistency which is indicative of mechanical problems, please investigate before resorting to software compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon offset relative to the center" TYPE={type} MSG={'"_N_%s_N__N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s"' % (recommendation, line_1, line_2, line_3, line_4, line_5, line_6, line_7, line_8)}

[gcode_macro BEACON_CREATE_SCAN_COMPENSATION_MESH]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set profile = params.PROFILE|default("auto")|string %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set keep_temp_meshes = params.KEEP_TEMP_MESHES|default(0) %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' %}
	{% set desired_spacing = printer["gcode_macro RatOS"].beacon_scan_compensation_desired_spacing|float %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	
	{% if not beacon_scan_compensation_enable %}
	RATOS_ECHO MSG="Beacon scan compensation is disabled!"
	
	{% else %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	
	
	RATOS_ECHO MSG="Please wait..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	G1 Z2.5 F{z_speed}
	{% if beacon_adaptive_heat_soak %}
	
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,9000]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if not (beacon_adaptive_heat_soak or bed_heat_soak_time > 0) %}
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if printer.z_tilt is defined %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% endif %}
	{% if printer.quad_gantry_level is defined %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% endif %}
	
	
	_BEACON_CREATE_SCAN_COMPENSATION_MESH_CORE PROFILE="{profile}" DESIRED_SPACING={desired_spacing} CHAMBER_TEMP={chamber_temp} KEEP_TEMP_MESHES={keep_temp_meshes}
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	{% if automated %}
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon scan compensation mesh created!"
	
	
	{% if not automated %}
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED]
gcode = 
	
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED" MSG="beacon_scan_compensation_profile {beacon_scan_compensation_profile}, beacon_scan_compensation_enable {beacon_scan_compensation_enable}"
	
	{% if beacon_scan_compensation_enable %}
	BEACON_APPLY_SCAN_COMPENSATION PROFILE="{beacon_scan_compensation_profile}"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL]
gcode = 
	
	{% set beacon_contact_start_print_true_zero = params.BEACON_CONTACT_START_PRINT_TRUE_ZERO|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = params.beacon_contact_calibrate_model_on_true_zero|lower == 'true' %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and not printer.beacon.model %}
	{% set beacon_model_required_for_true_zero = beacon_contact_start_print_true_zero and not beacon_contact_calibrate_model_on_true_zero %}
	{% set beacon_model_required_for_homing =
	printer.fastconfig.settings.stepper_z.endstop_pin == 'probe:z_virtual_endstop'
	and (( printer.fastconfig.settings.beacon.home_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower != 'true')
	or ( printer.fastconfig.settings.beacon.default_probe_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower != 'true' )) %}
	{% if beacon_model_required_for_homing or beacon_model_required_for_true_zero %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("An active Beacon model is required. Have you performed initial Beacon calibration?") }
	{% endif %}
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION]
gcode = 
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set bed_temp_mismatch_is_error = true if printer["gcode_macro RatOS"].beacon_scan_compensation_bed_temp_mismatch_is_error|default(false)|lower == 'true' else false %}
	
	{% set bed_temp = params.BED_TEMP|default(0)|float %}
	{% if bed_temp == 0 %}
	{% set bed_temp = printer.heater_bed.temperature %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_PREFLIGHT_CHECK_BEACON" MSG="beacon_scan_compensation_profile={beacon_scan_compensation_profile}, beacon_scan_compensation_enable={beacon_scan_compensation_enable}, bed_temp={bed_temp}"
	
	{% if beacon_scan_compensation_enable %}
	_VALIDATE_COMPENSATION_MESH_PROFILE PROFILE="{beacon_scan_compensation_profile}" TITLE="Check Beacon scan compensation profile" SUBJECT="Configured compensation profile '{beacon_scan_compensation_profile}'" COMPARE_BED_TEMP={bed_temp} COMPARE_BED_TEMP_IS_ERROR={bed_temp_mismatch_is_error}
	{% endif %}

[gcode_macro _BEACON_MAYBE_SCAN_COMPENSATION]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set needs_scan_compensation = true if printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].needs_compensation|default(false)|lower == 'true' else false %}
	
	{% if needs_scan_compensation %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% endif %}

[gcode_macro _BEACON_HOME_AND_ABL]
gcode = 
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	{% if needs_rehoming %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}

[gcode_macro SAVE_Z_OFFSET]
description = Deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead, or in Mainsail use the SAVE button in the Z-OFFSET section.
gcode = 
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default('false')|lower == 'true' %}
	{% set msg = "SAVE_Z_OFFSET is deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead,_N_or in Mainsail use the SAVE button in the Z-OFFSET section."%}
	{% if not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% set msg = msg + "_N_You must then use the SAVE_CONFIG command to persist the change." %}
	{% endif %}
	CONSOLE_ECHO TYPE="error" MSG="{msg}"

[gcode_macro _BEACON_OFFSET_COMPARE]
gcode = 
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing..."
	
	
	BEACON_OFFSET_COMPARE SAMPLES_DROP=1 SAMPLES=3
	BEACON_QUERY

[fan]
pin = rpi:gpio4

[fan_generic part_fan_t0]
pin = PA8
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[fan_generic part_fan_t1]
pin = PE5
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[heater_fan toolhead_cooling_fan_t0]
heater = extruder
shutdown_speed = 1
pin = toolboard_t0:PB4

[heater_fan toolhead_cooling_fan_t1]
heater = extruder1
shutdown_speed = 1
pin = toolboard_t1:PB4

[controller_fan controller_fan]
pin = dinghy:PA4
tachometer_pin = dinghy:PC15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[z_offset_probe]
pin = ^PG10
z_offset = -7
y_offset = 0
x_offset = 37.5
speed = 10
samples = 3
sample_retract_dist = 5
lift_speed = 10.0
samples_result = median
samples_tolerance = 0.2
samples_tolerance_retries = 5

[neopixel vaoc_led]
pin = PB10
chain_count = 6
color_order = GRB

[heater_fan vaoc_fan]
pin = PD13
heater = heater_bed
fan_speed = 1.0
heater_temp = 50

[fan_generic filter]
pin = !PD14
enable_pin = PD15

[gcode_macro T0]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = True
variable_color = "7bff33"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = -32.6
variable_parking_position = -57.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=0 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[gcode_macro T1]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = False
variable_color = "0ea5e9"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = 532.6
variable_parking_position = 557.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=1 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[save_variables]
filename = /home/pi/printer_data/config/ratos-variables.cfg

[mcu dinghy]
serial = /dev/serial/by-id/usb-Klipper_stm32f072xb_Dragon_dinghy-if00

[temperature_sensor th0]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA0

[temperature_sensor th1]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA1

[temperature_sensor th2]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA2

[temperature_sensor th3]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA3

[controller_fan CTL2]
pin = dinghy:PB14
tachometer_pin = dinghy:PB15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[mcu plasma]
serial = /dev/serial/by-id/usb-Klipper_rp2040_Plasma-if00

[neopixel Chamber_Lights]
pin = plasma:gpio15
chain_count = 140
color_order = GRBW
initial_red = 0.0
initial_green = 0.0
initial_blue = 0.0
initial_white = 0.1

[beacon model default]
model_coef = 1.5287863993594841,
	1.9289099639750602,
	0.8838828622507556,
	0.25554883784260735,
	-0.015171504024913506,
	0.3044946127013882,
	0.15820427856566457,
	-0.25262403959326246,
	0.042488512846660914,
	0.16662470122520964
model_domain = 1.842634574664148e-07,1.9339206373083917e-07
model_range = 0.200000,5.000000
model_temp = 13.222247
model_offset = 0.00000

[bed_mesh default]
version = 1
points = 
	0.016163, 0.016713, 0.001923, -0.017658, -0.031574, -0.032498, -0.030898, -0.032177, -0.035213, -0.031148, -0.021322, -0.016924, -0.015012, -0.013911, -0.012197, -0.012583, -0.010489, -0.007529, -0.003986, -0.000980, 0.005518, 0.014442, 0.027426, 0.034677, 0.037410, 0.040391, 0.041842, 0.040369, 0.037615, 0.030776, 0.027664, 0.022856, 0.016892, 0.015398, 0.014717, 0.006921, 0.001532, 0.000731, 0.008657, 0.014036
	0.005356, -0.005066, -0.016998, -0.029668, -0.038334, -0.043672, -0.041139, -0.042488, -0.045199, -0.039432, -0.028746, -0.023642, -0.024058, -0.022802, -0.019679, -0.018514, -0.018102, -0.016476, -0.012722, -0.010077, -0.001809, 0.007180, 0.019853, 0.027754, 0.029964, 0.033626, 0.036783, 0.032018, 0.029372, 0.020847, 0.017634, 0.011926, 0.009013, 0.009254, 0.007972, -0.001380, -0.006940, -0.002160, 0.006135, 0.008330
	-0.004900, -0.006720, -0.021914, -0.039691, -0.050459, -0.050377, -0.046281, -0.048755, -0.054708, -0.051499, -0.033927, -0.027632, -0.030243, -0.031447, -0.024387, -0.021408, -0.020382, -0.018068, -0.015930, -0.013877, -0.006099, 0.003479, 0.013310, 0.024783, 0.025522, 0.030849, 0.033573, 0.031409, 0.025495, 0.016683, 0.011264, 0.008805, 0.006856, 0.008059, 0.007305, 0.002581, -0.003320, -0.003239, 0.004691, 0.010045
	-0.008791, -0.019334, -0.029149, -0.040533, -0.051698, -0.058235, -0.054863, -0.054840, -0.055692, -0.049534, -0.036731, -0.033053, -0.035667, -0.035315, -0.024352, -0.023825, -0.022538, -0.020438, -0.018207, -0.015389, -0.006515, 0.001966, 0.013591, 0.019434, 0.020600, 0.024967, 0.029425, 0.026812, 0.018980, 0.007878, 0.002360, 0.000859, 0.003849, 0.005649, 0.005421, -0.000416, -0.007906, -0.003164, 0.007582, 0.010039
	-0.018512, -0.018210, -0.033932, -0.050501, -0.061588, -0.064139, -0.060236, -0.062528, -0.067065, -0.062039, -0.045815, -0.039448, -0.040521, -0.042080, -0.033870, -0.030878, -0.027396, -0.024548, -0.021298, -0.020041, -0.011880, -0.002847, 0.008689, 0.015857, 0.015934, 0.018697, 0.022439, 0.022106, 0.017916, 0.005879, 0.001037, -0.001311, -0.001335, 0.001897, 0.003656, 0.000561, -0.006084, -0.005683, 0.000338, 0.006245
	-0.028558, -0.036721, -0.044680, -0.054969, -0.066140, -0.075045, -0.073515, -0.073161, -0.075696, -0.068963, -0.058892, -0.053111, -0.050990, -0.048040, -0.041262, -0.037419, -0.034866, -0.031845, -0.029787, -0.026524, -0.017896, -0.009322, -0.001010, 0.005819, 0.008058, 0.010456, 0.013266, 0.012529, 0.007992, -0.001491, -0.006769, -0.009303, -0.005980, -0.003567, -0.003340, -0.011496, -0.018818, -0.014808, -0.004181, -0.000733
	-0.037253, -0.038393, -0.053129, -0.066170, -0.075959, -0.079233, -0.077475, -0.082688, -0.086779, -0.083983, -0.069005, -0.062542, -0.060351, -0.058481, -0.051101, -0.043149, -0.039837, -0.037039, -0.034698, -0.031301, -0.024330, -0.019786, -0.010285, -0.001967, 0.002812, 0.004899, 0.009657, 0.006946, 0.002155, -0.005232, -0.009851, -0.011218, -0.011509, -0.010097, -0.010293, -0.013175, -0.018958, -0.019846, -0.012107, -0.005641
	-0.046584, -0.055590, -0.062606, -0.069218, -0.080399, -0.087414, -0.089037, -0.092376, -0.095115, -0.088957, -0.080802, -0.073290, -0.068741, -0.064591, -0.054452, -0.048270, -0.045916, -0.044559, -0.042047, -0.039605, -0.032667, -0.025789, -0.019495, -0.012773, -0.006697, -0.003025, 0.001413, 0.000817, -0.004738, -0.013008, -0.017605, -0.018191, -0.018524, -0.016356, -0.016750, -0.021992, -0.028943, -0.025791, -0.016146, -0.010447
	-0.051029, -0.051677, -0.068218, -0.079622, -0.088590, -0.089331, -0.089731, -0.096072, -0.105329, -0.100771, -0.087584, -0.079320, -0.075489, -0.072081, -0.064183, -0.054662, -0.048601, -0.049465, -0.047050, -0.045011, -0.040009, -0.032508, -0.025212, -0.018144, -0.011996, -0.008136, -0.003187, -0.003214, -0.006646, -0.013044, -0.019446, -0.020615, -0.022270, -0.021298, -0.020215, -0.020946, -0.026034, -0.026598, -0.021025, -0.012328
	-0.057184, -0.064908, -0.073093, -0.081584, -0.091971, -0.097048, -0.097688, -0.101869, -0.106651, -0.102162, -0.095658, -0.087938, -0.082718, -0.077017, -0.069608, -0.060682, -0.056889, -0.056864, -0.054260, -0.052011, -0.044563, -0.038927, -0.031943, -0.025832, -0.021170, -0.014319, -0.009046, -0.008543, -0.011751, -0.020287, -0.026608, -0.027259, -0.029120, -0.025549, -0.023221, -0.027725, -0.032477, -0.028427, -0.019343, -0.014932
	-0.060411, -0.062241, -0.080781, -0.090744, -0.100903, -0.099702, -0.098468, -0.104236, -0.116853, -0.112701, -0.102623, -0.095036, -0.091407, -0.089871, -0.079701, -0.070222, -0.064325, -0.063875, -0.062248, -0.059396, -0.052699, -0.047589, -0.041526, -0.028442, -0.024526, -0.019549, -0.015403, -0.014251, -0.017989, -0.022824, -0.027328, -0.029155, -0.033315, -0.032426, -0.027619, -0.030776, -0.033688, -0.032458, -0.027219, -0.019649
	-0.067541, -0.076514, -0.082321, -0.088656, -0.099968, -0.104930, -0.105875, -0.109051, -0.115531, -0.112996, -0.105760, -0.100390, -0.096171, -0.090011, -0.080050, -0.073632, -0.067451, -0.067031, -0.065225, -0.062471, -0.056370, -0.050129, -0.041626, -0.030801, -0.027579, -0.022472, -0.014826, -0.015306, -0.020316, -0.025953, -0.030661, -0.034103, -0.035502, -0.032738, -0.031311, -0.037314, -0.041306, -0.035280, -0.027449, -0.020395
	-0.068162, -0.069269, -0.088235, -0.096809, -0.103385, -0.103271, -0.102507, -0.109535, -0.123412, -0.118580, -0.106622, -0.099580, -0.097644, -0.096978, -0.087259, -0.077196, -0.068978, -0.067016, -0.063682, -0.062548, -0.057901, -0.052295, -0.044088, -0.032703, -0.026551, -0.021607, -0.014155, -0.013747, -0.017390, -0.022419, -0.027444, -0.030877, -0.033450, -0.032423, -0.032041, -0.033598, -0.035149, -0.034054, -0.029356, -0.020998
	-0.069473, -0.075924, -0.083569, -0.089648, -0.101235, -0.105828, -0.109144, -0.112613, -0.117233, -0.114186, -0.107090, -0.098616, -0.097084, -0.094257, -0.086773, -0.076409, -0.069532, -0.066472, -0.060956, -0.059191, -0.052886, -0.047752, -0.041275, -0.032437, -0.027780, -0.020398, -0.012061, -0.010133, -0.014056, -0.021528, -0.027924, -0.030605, -0.030609, -0.026068, -0.029346, -0.033991, -0.038254, -0.030610, -0.021109, -0.015885
	-0.068084, -0.066409, -0.083944, -0.094013, -0.102504, -0.105274, -0.106036, -0.112090, -0.121664, -0.117824, -0.104850, -0.097467, -0.098833, -0.098622, -0.089603, -0.078147, -0.068143, -0.066300, -0.061573, -0.057727, -0.054825, -0.048625, -0.040164, -0.030532, -0.025948, -0.020264, -0.014196, -0.010702, -0.013794, -0.019775, -0.026095, -0.028838, -0.030254, -0.027944, -0.027980, -0.030915, -0.032446, -0.028861, -0.023732, -0.014676
	-0.065280, -0.068669, -0.076948, -0.082397, -0.094986, -0.105117, -0.107099, -0.108954, -0.112557, -0.110326, -0.100725, -0.096325, -0.096240, -0.092388, -0.081185, -0.071682, -0.065650, -0.062250, -0.057027, -0.054691, -0.048349, -0.042069, -0.032712, -0.027728, -0.023396, -0.018458, -0.008357, -0.005699, -0.011447, -0.020033, -0.026387, -0.030280, -0.028443, -0.023735, -0.023838, -0.031580, -0.034204, -0.027768, -0.018029, -0.010628
	-0.061662, -0.057052, -0.075163, -0.086710, -0.094182, -0.097544, -0.098814, -0.105908, -0.114460, -0.111718, -0.097559, -0.091614, -0.093860, -0.093098, -0.081687, -0.069410, -0.064117, -0.062745, -0.055603, -0.051413, -0.048043, -0.040363, -0.031842, -0.023420, -0.017470, -0.012600, -0.008163, -0.003898, -0.007635, -0.013254, -0.019807, -0.025153, -0.027074, -0.023513, -0.023727, -0.028669, -0.029153, -0.024831, -0.018735, -0.009246
	-0.056176, -0.059439, -0.066501, -0.071527, -0.085216, -0.094918, -0.097595, -0.099419, -0.101847, -0.102015, -0.093849, -0.089867, -0.088840, -0.083167, -0.071832, -0.062522, -0.058023, -0.057771, -0.053050, -0.048285, -0.041374, -0.033527, -0.024473, -0.018428, -0.013958, -0.008161, -0.001196, 0.001754, -0.004016, -0.011132, -0.018325, -0.021813, -0.021514, -0.016948, -0.018061, -0.025702, -0.028671, -0.021470, -0.011028, -0.001934
	-0.059202, -0.050525, -0.065461, -0.076792, -0.084156, -0.088538, -0.090719, -0.096070, -0.105729, -0.105136, -0.090350, -0.083865, -0.087807, -0.086145, -0.074773, -0.064235, -0.057641, -0.055896, -0.051286, -0.046566, -0.042431, -0.034723, -0.023762, -0.014983, -0.009126, -0.004877, 0.000094, 0.003492, -0.000931, -0.005883, -0.011665, -0.015251, -0.016432, -0.016119, -0.015373, -0.018827, -0.019994, -0.017564, -0.012298, 0.002094
	-0.055561, -0.058184, -0.062669, -0.068111, -0.080741, -0.091895, -0.093911, -0.094387, -0.100239, -0.100695, -0.089841, -0.085682, -0.085212, -0.082910, -0.073072, -0.063594, -0.056157, -0.053482, -0.048107, -0.045405, -0.039982, -0.029777, -0.019905, -0.013872, -0.009732, -0.004272, 0.003500, 0.006909, 0.001302, -0.004626, -0.012374, -0.014751, -0.014637, -0.011794, -0.012913, -0.018244, -0.023377, -0.018086, -0.006575, 0.003294
	-0.062834, -0.047300, -0.060870, -0.073023, -0.079303, -0.082121, -0.083623, -0.091321, -0.100996, -0.098896, -0.085406, -0.078881, -0.081932, -0.082077, -0.074409, -0.063158, -0.053822, -0.050328, -0.045077, -0.039678, -0.035825, -0.028532, -0.017793, -0.009121, -0.003444, -0.000905, 0.003990, 0.007745, 0.004595, 0.000143, -0.004555, -0.007411, -0.010850, -0.010100, -0.010079, -0.013177, -0.016434, -0.014663, -0.010248, -0.000213
	-0.054748, -0.053907, -0.057576, -0.063118, -0.072478, -0.081366, -0.084424, -0.086348, -0.089718, -0.089305, -0.081771, -0.076889, -0.076923, -0.073518, -0.067973, -0.057643, -0.050848, -0.046966, -0.041560, -0.036436, -0.029233, -0.020685, -0.010240, -0.004935, -0.001084, 0.002478, 0.009168, 0.014038, 0.010885, 0.004752, -0.001650, -0.004209, -0.003998, -0.002336, -0.003784, -0.010930, -0.016480, -0.012798, -0.003650, 0.002998
	-0.059345, -0.041989, -0.057435, -0.068229, -0.072857, -0.072586, -0.075155, -0.083286, -0.091292, -0.089727, -0.073702, -0.068353, -0.072910, -0.073863, -0.065527, -0.053635, -0.046064, -0.043899, -0.037607, -0.031251, -0.026194, -0.018885, -0.008095, 0.000309, 0.004911, 0.007046, 0.010642, 0.015635, 0.015277, 0.012612, 0.008074, 0.004852, 0.001546, 0.000504, 0.000589, -0.002769, -0.006432, -0.007765, -0.005391, 0.006950
	-0.050324, -0.049088, -0.052417, -0.057257, -0.063818, -0.071057, -0.074636, -0.075459, -0.079445, -0.077368, -0.068788, -0.063940, -0.065040, -0.063419, -0.054864, -0.044910, -0.038774, -0.036951, -0.031149, -0.026080, -0.018383, -0.011985, -0.001732, 0.003893, 0.007180, 0.011120, 0.017429, 0.021738, 0.019167, 0.015812, 0.011027, 0.007243, 0.006720, 0.009346, 0.006598, -0.003776, -0.009199, -0.007592, 0.005481, 0.014396
	-0.058437, -0.035937, -0.050762, -0.060425, -0.061123, -0.059090, -0.062399, -0.072124, -0.080338, -0.074950, -0.060985, -0.054754, -0.059333, -0.060500, -0.051714, -0.038834, -0.031117, -0.031693, -0.025186, -0.017982, -0.014316, -0.010137, 0.000228, 0.008774, 0.014018, 0.016470, 0.019918, 0.022071, 0.021109, 0.019957, 0.018698, 0.015803, 0.013135, 0.011136, 0.008719, 0.003522, -0.000994, 0.000525, 0.006297, 0.018454
	-0.046143, -0.041577, -0.045391, -0.046668, -0.051722, -0.057607, -0.062802, -0.065205, -0.068243, -0.066293, -0.058216, -0.051324, -0.051806, -0.051018, -0.043393, -0.032431, -0.024016, -0.023321, -0.018504, -0.013897, -0.008455, -0.001123, 0.006609, 0.010462, 0.013887, 0.019328, 0.024804, 0.026590, 0.023420, 0.020337, 0.017129, 0.017199, 0.016391, 0.015616, 0.013257, 0.005832, -0.000019, 0.003462, 0.014308, 0.023624
	-0.051989, -0.030294, -0.043380, -0.051339, -0.050711, -0.048193, -0.052258, -0.061218, -0.070507, -0.068810, -0.049476, -0.042352, -0.046018, -0.046673, -0.038670, -0.027263, -0.018137, -0.018587, -0.013603, -0.008482, -0.004647, -0.000011, 0.008230, 0.015652, 0.019436, 0.023069, 0.024762, 0.027750, 0.028115, 0.026227, 0.022220, 0.023166, 0.020341, 0.018455, 0.014918, 0.011932, 0.007138, 0.008523, 0.014718, 0.026201
	-0.041448, -0.035286, -0.036538, -0.037577, -0.044652, -0.049300, -0.051092, -0.052841, -0.058068, -0.056947, -0.046235, -0.038436, -0.037494, -0.034175, -0.028932, -0.016904, -0.010075, -0.010552, -0.004464, -0.001243, 0.003236, 0.010200, 0.015604, 0.020362, 0.023157, 0.028023, 0.032826, 0.035958, 0.034819, 0.030600, 0.025988, 0.026013, 0.026284, 0.025661, 0.022322, 0.013336, 0.006464, 0.011312, 0.022330, 0.031668
	-0.048540, -0.022534, -0.035260, -0.042156, -0.042749, -0.037408, -0.038818, -0.047322, -0.056808, -0.053643, -0.035691, -0.027822, -0.028789, -0.028255, -0.020274, -0.007285, -0.000723, -0.000788, 0.005440, 0.008938, 0.008953, 0.012074, 0.017957, 0.025241, 0.029175, 0.032057, 0.033733, 0.038359, 0.039349, 0.037161, 0.034052, 0.034585, 0.032020, 0.029940, 0.026326, 0.024577, 0.020432, 0.021586, 0.024568, 0.034552
	-0.033086, -0.027982, -0.029443, -0.029011, -0.035629, -0.040579, -0.038290, -0.037389, -0.041260, -0.040430, -0.032279, -0.021394, -0.018817, -0.015525, -0.007558, 0.006345, 0.011048, 0.011271, 0.013497, 0.017030, 0.017449, 0.022752, 0.026764, 0.030722, 0.033532, 0.037203, 0.043356, 0.048536, 0.047776, 0.043851, 0.039311, 0.039944, 0.039954, 0.038931, 0.034893, 0.030946, 0.023127, 0.027359, 0.034859, 0.043920
	-0.036218, -0.016846, -0.030897, -0.036980, -0.037261, -0.033334, -0.030888, -0.034074, -0.042142, -0.039980, -0.021377, -0.013603, -0.014171, -0.013131, -0.001768, 0.014998, 0.020060, 0.018173, 0.019934, 0.024704, 0.023739, 0.024617, 0.027288, 0.035116, 0.041187, 0.043128, 0.045921, 0.051709, 0.053031, 0.050698, 0.047697, 0.047728, 0.046845, 0.043201, 0.041805, 0.040728, 0.036184, 0.034435, 0.035120, 0.045329
	-0.029808, -0.023871, -0.026541, -0.026705, -0.031203, -0.036908, -0.034411, -0.029231, -0.028090, -0.026102, -0.016691, -0.007747, -0.004471, 0.001560, 0.010738, 0.025062, 0.027672, 0.024833, 0.026976, 0.029502, 0.030754, 0.035709, 0.039403, 0.044719, 0.046379, 0.049250, 0.054178, 0.059793, 0.059542, 0.052111, 0.047608, 0.050103, 0.053142, 0.052747, 0.050045, 0.044102, 0.033149, 0.035392, 0.045678, 0.054080
	-0.032238, -0.008993, -0.023999, -0.030969, -0.028658, -0.024887, -0.024493, -0.028088, -0.031053, -0.022849, -0.003868, 0.004647, 0.004540, 0.007560, 0.018373, 0.031401, 0.035778, 0.033768, 0.035173, 0.035884, 0.036597, 0.038940, 0.044566, 0.053914, 0.056554, 0.056382, 0.056449, 0.060387, 0.062696, 0.058223, 0.055016, 0.056193, 0.056891, 0.052793, 0.052741, 0.052626, 0.048117, 0.045032, 0.048033, 0.055100
	-0.019758, -0.015110, -0.017814, -0.018871, -0.023340, -0.028653, -0.026880, -0.018681, -0.017020, -0.011343, -0.001002, 0.008249, 0.014012, 0.020367, 0.026878, 0.038534, 0.041827, 0.039532, 0.039775, 0.039109, 0.043172, 0.049325, 0.056604, 0.059583, 0.059329, 0.059876, 0.062766, 0.068759, 0.067214, 0.059657, 0.055950, 0.056798, 0.058619, 0.058591, 0.059849, 0.056473, 0.046841, 0.047921, 0.058342, 0.065346
	-0.018628, -0.000296, -0.014764, -0.022634, -0.020483, -0.016362, -0.015485, -0.017352, -0.020246, -0.010362, 0.008635, 0.018414, 0.018542, 0.024258, 0.033370, 0.045728, 0.049983, 0.044610, 0.044638, 0.047649, 0.049220, 0.051954, 0.058932, 0.065915, 0.069102, 0.067410, 0.067680, 0.073734, 0.072203, 0.067293, 0.063945, 0.064378, 0.065047, 0.061989, 0.062882, 0.063468, 0.059707, 0.057986, 0.059739, 0.066139
	-0.010091, -0.006551, -0.008018, -0.009589, -0.016068, -0.020662, -0.019451, -0.010985, -0.009391, -0.003580, 0.007826, 0.019598, 0.024961, 0.033762, 0.040618, 0.050868, 0.052139, 0.050495, 0.049198, 0.051777, 0.056840, 0.061771, 0.068414, 0.072295, 0.073443, 0.072145, 0.073414, 0.079338, 0.075988, 0.067367, 0.064745, 0.064435, 0.066982, 0.065811, 0.067424, 0.063230, 0.058438, 0.059982, 0.067672, 0.072460
	-0.016254, 0.006291, -0.008031, -0.013944, -0.014475, -0.010741, -0.009932, -0.011709, -0.015503, -0.006971, 0.013190, 0.024865, 0.029121, 0.033942, 0.044335, 0.054572, 0.058078, 0.055224, 0.055897, 0.058327, 0.061207, 0.063939, 0.070506, 0.078141, 0.084203, 0.081223, 0.079519, 0.082883, 0.080890, 0.076174, 0.071279, 0.073064, 0.071225, 0.066859, 0.069860, 0.070836, 0.069427, 0.069140, 0.070950, 0.075269
	-0.008127, 0.000730, 0.001164, -0.000308, -0.006659, -0.012343, -0.011463, -0.003755, -0.001876, 0.005166, 0.016616, 0.030243, 0.036509, 0.045020, 0.053681, 0.063738, 0.066425, 0.063964, 0.062796, 0.065633, 0.071912, 0.077280, 0.082580, 0.086477, 0.089798, 0.089603, 0.091453, 0.096125, 0.088708, 0.079903, 0.074317, 0.076190, 0.075399, 0.075242, 0.079628, 0.077855, 0.071473, 0.073702, 0.082757, 0.088086
	-0.010951, 0.013218, -0.000878, -0.006241, -0.005623, 0.000046, 0.000158, -0.002943, -0.005314, 0.005491, 0.026890, 0.035754, 0.041490, 0.045829, 0.059325, 0.070249, 0.074114, 0.071815, 0.073229, 0.076313, 0.080778, 0.081554, 0.087919, 0.096206, 0.101562, 0.101674, 0.100494, 0.103989, 0.100292, 0.093977, 0.088080, 0.088136, 0.086555, 0.081494, 0.084966, 0.087073, 0.084113, 0.085184, 0.087700, 0.092188
	-0.002972, 0.006020, 0.006098, 0.004303, 0.001326, -0.002386, -0.001840, 0.005325, 0.008624, 0.016246, 0.026781, 0.039696, 0.048540, 0.055938, 0.066982, 0.076497, 0.080828, 0.079669, 0.080127, 0.083754, 0.089783, 0.093456, 0.100570, 0.105322, 0.107132, 0.110571, 0.113141, 0.118064, 0.111721, 0.101634, 0.093555, 0.093112, 0.093104, 0.092325, 0.094780, 0.092552, 0.085283, 0.088882, 0.097508, 0.105280
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 11.4
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Preperations]
version = 1
points = 
	0.012158, -0.006098, -0.020628, -0.034069, -0.049418, -0.058491, -0.062706, -0.063181, -0.065552, -0.063461, -0.057373, -0.056717, -0.056579, -0.054080, -0.053373, -0.056878, -0.057281, -0.055224, -0.049676, -0.047605, -0.041454, -0.034605, -0.022490, -0.011292, -0.009411, -0.005344, -0.003510, -0.002717, -0.005999, -0.010712, -0.013141, -0.015611, -0.020004, -0.017667, -0.016629, -0.022248, -0.024864, -0.024065, -0.014921, -0.010826
	-0.005958, -0.021084, -0.033800, -0.047903, -0.059950, -0.071345, -0.072502, -0.073350, -0.075852, -0.072963, -0.067236, -0.064315, -0.065698, -0.064338, -0.062871, -0.065238, -0.067095, -0.063584, -0.059241, -0.057846, -0.051380, -0.043157, -0.030230, -0.019950, -0.018121, -0.014291, -0.009354, -0.013065, -0.016464, -0.022925, -0.025337, -0.026541, -0.030577, -0.029068, -0.027094, -0.030532, -0.034241, -0.032625, -0.021498, -0.020513
	-0.017526, -0.027763, -0.040710, -0.055305, -0.068172, -0.079641, -0.081247, -0.081903, -0.083679, -0.081855, -0.073270, -0.070340, -0.072083, -0.071536, -0.066055, -0.065901, -0.069085, -0.066531, -0.063284, -0.061616, -0.053366, -0.047292, -0.035451, -0.023167, -0.022205, -0.016699, -0.012552, -0.014153, -0.018802, -0.030443, -0.032210, -0.034051, -0.034437, -0.031439, -0.030406, -0.032817, -0.036351, -0.034849, -0.024250, -0.019489
	-0.017750, -0.030284, -0.043463, -0.055839, -0.071865, -0.084888, -0.086157, -0.084619, -0.086681, -0.084515, -0.075246, -0.073263, -0.075604, -0.075123, -0.069177, -0.070723, -0.071097, -0.068644, -0.065465, -0.063718, -0.057574, -0.049335, -0.036556, -0.028418, -0.028259, -0.023387, -0.018454, -0.020519, -0.027499, -0.038314, -0.041534, -0.041886, -0.039972, -0.036438, -0.033959, -0.033009, -0.038291, -0.036339, -0.022688, -0.024783
	-0.021354, -0.034103, -0.047541, -0.060551, -0.075691, -0.089373, -0.092241, -0.091621, -0.093203, -0.090723, -0.082480, -0.079781, -0.079706, -0.079674, -0.074365, -0.073780, -0.073465, -0.070165, -0.064970, -0.065503, -0.059104, -0.051038, -0.041817, -0.031243, -0.031386, -0.028837, -0.023658, -0.024237, -0.029641, -0.039210, -0.042766, -0.044461, -0.041863, -0.039075, -0.034881, -0.034571, -0.039386, -0.038253, -0.031659, -0.024202
	-0.027696, -0.041184, -0.054054, -0.064759, -0.080898, -0.094964, -0.097906, -0.098033, -0.101256, -0.098300, -0.091517, -0.088420, -0.086945, -0.085220, -0.079938, -0.079979, -0.079828, -0.074842, -0.072903, -0.072415, -0.065384, -0.057454, -0.048482, -0.040977, -0.039336, -0.036065, -0.032553, -0.034336, -0.039337, -0.046271, -0.049398, -0.051220, -0.049530, -0.045000, -0.045029, -0.042100, -0.049767, -0.046386, -0.035574, -0.032188
	-0.033426, -0.046259, -0.059363, -0.068024, -0.084858, -0.097009, -0.103434, -0.106215, -0.107319, -0.106178, -0.100333, -0.097536, -0.095352, -0.091322, -0.086332, -0.082309, -0.081440, -0.078413, -0.075067, -0.073134, -0.068255, -0.062667, -0.054300, -0.046004, -0.042001, -0.039181, -0.035010, -0.036092, -0.041599, -0.048788, -0.051751, -0.051179, -0.051019, -0.049121, -0.045860, -0.046756, -0.050005, -0.051613, -0.040237, -0.035349
	-0.037931, -0.051993, -0.066455, -0.075044, -0.088177, -0.102890, -0.108223, -0.112373, -0.115787, -0.113421, -0.108543, -0.105936, -0.101048, -0.096863, -0.090726, -0.087882, -0.086665, -0.083874, -0.081096, -0.080894, -0.075125, -0.071038, -0.063072, -0.054696, -0.051039, -0.046728, -0.042566, -0.043887, -0.048745, -0.056834, -0.059808, -0.060521, -0.060664, -0.057968, -0.056317, -0.052477, -0.058814, -0.055877, -0.046325, -0.042545
	-0.041429, -0.053634, -0.067633, -0.077111, -0.090998, -0.103561, -0.109445, -0.114741, -0.120075, -0.119821, -0.114703, -0.110411, -0.105589, -0.099826, -0.093730, -0.089705, -0.087199, -0.086439, -0.082688, -0.082221, -0.078348, -0.073203, -0.065273, -0.058731, -0.054025, -0.049231, -0.044830, -0.043830, -0.045839, -0.054137, -0.059075, -0.059515, -0.058546, -0.056956, -0.054145, -0.053129, -0.056587, -0.056341, -0.047057, -0.039936
	-0.044295, -0.058972, -0.072101, -0.082726, -0.095001, -0.106449, -0.111505, -0.118363, -0.124608, -0.123506, -0.120263, -0.115400, -0.110227, -0.104535, -0.100348, -0.095757, -0.092961, -0.092377, -0.089613, -0.088047, -0.084834, -0.079314, -0.072500, -0.064519, -0.060449, -0.055767, -0.051803, -0.050997, -0.052855, -0.058115, -0.063348, -0.065363, -0.067936, -0.063474, -0.061475, -0.054726, -0.062529, -0.055352, -0.048878, -0.044991
	-0.045804, -0.056574, -0.073308, -0.082450, -0.097495, -0.107467, -0.111501, -0.116418, -0.126724, -0.125980, -0.123231, -0.120494, -0.114667, -0.111289, -0.103451, -0.099228, -0.095880, -0.095882, -0.093328, -0.091000, -0.087051, -0.081909, -0.075949, -0.064971, -0.061050, -0.055137, -0.049046, -0.047319, -0.049806, -0.056968, -0.059608, -0.060249, -0.063032, -0.060556, -0.056284, -0.056263, -0.058891, -0.057890, -0.051554, -0.042382
	-0.049818, -0.062681, -0.076305, -0.084328, -0.098717, -0.107866, -0.113937, -0.120088, -0.128622, -0.128931, -0.126353, -0.123191, -0.118529, -0.115642, -0.106288, -0.103976, -0.099708, -0.097750, -0.094501, -0.094545, -0.090910, -0.085952, -0.077352, -0.067196, -0.062435, -0.057738, -0.052934, -0.051098, -0.055294, -0.061112, -0.063120, -0.067525, -0.067979, -0.066558, -0.064608, -0.060597, -0.067812, -0.057641, -0.056224, -0.046471
	-0.050591, -0.060432, -0.075602, -0.083877, -0.096933, -0.106147, -0.112334, -0.118295, -0.127966, -0.128757, -0.125157, -0.121831, -0.118557, -0.116124, -0.108723, -0.104502, -0.099469, -0.095841, -0.090662, -0.089822, -0.087969, -0.084545, -0.076375, -0.064821, -0.059093, -0.053427, -0.047372, -0.044341, -0.047964, -0.054064, -0.057133, -0.059152, -0.061568, -0.059109, -0.056640, -0.056691, -0.056844, -0.054564, -0.048514, -0.040641
	-0.047704, -0.059564, -0.073127, -0.080945, -0.093764, -0.105483, -0.111501, -0.118792, -0.124812, -0.126576, -0.122064, -0.118087, -0.116126, -0.114867, -0.108053, -0.103336, -0.097558, -0.093250, -0.086537, -0.085303, -0.083677, -0.079292, -0.070542, -0.062526, -0.056818, -0.052534, -0.044035, -0.041353, -0.046942, -0.051329, -0.055481, -0.062777, -0.058499, -0.058025, -0.057390, -0.053562, -0.060843, -0.046555, -0.046260, -0.036083
	-0.046496, -0.052983, -0.067518, -0.076904, -0.091704, -0.103105, -0.111995, -0.117751, -0.122307, -0.122941, -0.118230, -0.115004, -0.114258, -0.113138, -0.105515, -0.098417, -0.093384, -0.090070, -0.083281, -0.079846, -0.078725, -0.075452, -0.066225, -0.057269, -0.053103, -0.047808, -0.039772, -0.036834, -0.041270, -0.047376, -0.051111, -0.053848, -0.053029, -0.050301, -0.048919, -0.050775, -0.050121, -0.046842, -0.039633, -0.030497
	-0.040695, -0.051685, -0.064038, -0.070974, -0.086679, -0.101773, -0.109889, -0.114373, -0.117883, -0.118764, -0.113125, -0.110931, -0.111099, -0.109664, -0.098733, -0.093182, -0.090154, -0.086213, -0.077214, -0.077108, -0.075555, -0.069117, -0.060704, -0.054093, -0.049253, -0.044799, -0.037536, -0.035304, -0.040134, -0.045456, -0.051720, -0.056675, -0.053743, -0.052923, -0.049701, -0.050238, -0.056776, -0.041485, -0.041755, -0.027329
	-0.039842, -0.039428, -0.055732, -0.063890, -0.079179, -0.092823, -0.101698, -0.106156, -0.111709, -0.113152, -0.108033, -0.104872, -0.105645, -0.103501, -0.094487, -0.087264, -0.084273, -0.080950, -0.074116, -0.070973, -0.068409, -0.062825, -0.054757, -0.044150, -0.040620, -0.036602, -0.031538, -0.026478, -0.031123, -0.037600, -0.042341, -0.046700, -0.047380, -0.042880, -0.040967, -0.045367, -0.044192, -0.038553, -0.029948, -0.020790
	-0.030596, -0.038279, -0.051528, -0.058981, -0.073983, -0.089044, -0.099173, -0.101740, -0.104830, -0.107083, -0.102306, -0.101554, -0.101336, -0.097146, -0.089217, -0.083800, -0.080621, -0.078071, -0.071535, -0.068328, -0.065806, -0.056882, -0.048683, -0.039756, -0.036349, -0.031328, -0.025351, -0.024133, -0.029773, -0.033858, -0.040011, -0.044146, -0.043900, -0.044797, -0.038019, -0.042319, -0.047297, -0.031851, -0.034318, -0.013527
	-0.032121, -0.034722, -0.047839, -0.054710, -0.069175, -0.084213, -0.094533, -0.097233, -0.100863, -0.104775, -0.099781, -0.097416, -0.098804, -0.096059, -0.086694, -0.079692, -0.076749, -0.074609, -0.068106, -0.063906, -0.061136, -0.055447, -0.045559, -0.035389, -0.029696, -0.025708, -0.020034, -0.017335, -0.022665, -0.028532, -0.032369, -0.035760, -0.037212, -0.035201, -0.032872, -0.034132, -0.035907, -0.032127, -0.025026, -0.009282
	-0.026707, -0.034374, -0.045183, -0.052691, -0.067014, -0.084964, -0.092286, -0.094441, -0.099291, -0.103609, -0.098278, -0.094972, -0.097169, -0.095394, -0.086653, -0.080205, -0.076284, -0.070594, -0.064535, -0.062012, -0.060174, -0.051216, -0.040622, -0.033396, -0.029636, -0.024235, -0.017274, -0.018232, -0.021459, -0.024778, -0.031754, -0.034481, -0.033398, -0.037949, -0.030432, -0.033219, -0.038432, -0.021975, -0.030052, -0.009295
	-0.028559, -0.029280, -0.042071, -0.048655, -0.061603, -0.076257, -0.086817, -0.091815, -0.095682, -0.098682, -0.093729, -0.091168, -0.092213, -0.090073, -0.084070, -0.077048, -0.072045, -0.066267, -0.060309, -0.053639, -0.051696, -0.046852, -0.034069, -0.025602, -0.020640, -0.018021, -0.013180, -0.009049, -0.013846, -0.018012, -0.021061, -0.024515, -0.027068, -0.026804, -0.024283, -0.025595, -0.028234, -0.025272, -0.019246, -0.008595
	-0.025711, -0.029003, -0.038836, -0.048015, -0.058511, -0.074480, -0.083738, -0.087945, -0.091439, -0.094310, -0.090288, -0.087858, -0.088589, -0.086163, -0.081829, -0.075146, -0.071136, -0.064399, -0.057338, -0.052103, -0.049650, -0.043210, -0.032998, -0.023124, -0.020191, -0.016625, -0.012433, -0.010465, -0.009871, -0.015007, -0.021217, -0.021582, -0.023800, -0.027652, -0.021527, -0.027137, -0.030828, -0.020152, -0.026202, -0.008568
	-0.031287, -0.022523, -0.035800, -0.041583, -0.052691, -0.065901, -0.075941, -0.079246, -0.083936, -0.086778, -0.082235, -0.078893, -0.080642, -0.079419, -0.074324, -0.067418, -0.062113, -0.057744, -0.049923, -0.043390, -0.040055, -0.035512, -0.023838, -0.015485, -0.009895, -0.008346, -0.005387, 0.001467, -0.000104, -0.003777, -0.007926, -0.012023, -0.013970, -0.014207, -0.013994, -0.017009, -0.019233, -0.019282, -0.014210, -0.001146
	-0.020719, -0.024043, -0.035160, -0.041635, -0.051902, -0.063884, -0.072884, -0.076738, -0.081856, -0.083761, -0.077857, -0.074651, -0.077952, -0.076310, -0.069721, -0.063240, -0.056775, -0.055188, -0.046711, -0.042996, -0.039499, -0.032268, -0.023129, -0.015735, -0.012305, -0.009383, -0.005789, -0.001996, -0.001166, -0.005106, -0.009634, -0.009864, -0.011905, -0.015913, -0.010246, -0.016645, -0.022975, -0.011972, -0.018524, 0.001048
	-0.026050, -0.019774, -0.032555, -0.037813, -0.044657, -0.054435, -0.065271, -0.071019, -0.075585, -0.077479, -0.072635, -0.069526, -0.071046, -0.070770, -0.063085, -0.055960, -0.050956, -0.049593, -0.042773, -0.034996, -0.032645, -0.029030, -0.020343, -0.011008, -0.005751, -0.003252, 0.000746, 0.003215, 0.001749, -0.000068, -0.001413, -0.002608, -0.005837, -0.007103, -0.008431, -0.012027, -0.015656, -0.014417, -0.006321, 0.003748
	-0.021728, -0.019178, -0.031232, -0.036249, -0.042206, -0.053190, -0.064017, -0.068545, -0.074597, -0.074544, -0.069543, -0.065779, -0.067928, -0.067354, -0.060655, -0.052790, -0.047723, -0.046044, -0.038188, -0.034539, -0.032080, -0.027152, -0.018902, -0.012508, -0.009304, -0.003955, -0.000288, -0.001549, -0.000556, -0.003756, -0.008467, -0.003851, -0.005999, -0.012959, -0.007423, -0.015332, -0.017388, -0.005695, -0.010807, 0.007710
	-0.028204, -0.017096, -0.027984, -0.032129, -0.038374, -0.046561, -0.059356, -0.061847, -0.069228, -0.070551, -0.065474, -0.059719, -0.059893, -0.060271, -0.053666, -0.047202, -0.041189, -0.039979, -0.033189, -0.028761, -0.025714, -0.021660, -0.014905, -0.007841, -0.004669, -0.001174, 0.001874, 0.005613, 0.005527, 0.001504, -0.000694, 0.001892, 0.001885, -0.002506, -0.005619, -0.007166, -0.009935, -0.007406, 0.000545, 0.009983
	-0.019393, -0.017785, -0.025482, -0.028146, -0.036861, -0.047528, -0.055696, -0.059118, -0.064151, -0.066346, -0.060565, -0.055661, -0.055495, -0.051944, -0.048147, -0.040645, -0.036359, -0.035990, -0.026764, -0.024843, -0.023572, -0.019648, -0.013807, -0.006811, -0.004589, -0.000266, 0.003010, 0.004931, 0.006834, 0.003254, -0.001690, 0.003120, 0.001036, -0.005283, 0.000659, -0.007399, -0.010996, -0.000832, -0.006381, 0.012135
	-0.021519, -0.010062, -0.018662, -0.023011, -0.029067, -0.036961, -0.043194, -0.048197, -0.053632, -0.055489, -0.050054, -0.045247, -0.042655, -0.040243, -0.034315, -0.027094, -0.022697, -0.021644, -0.015333, -0.010768, -0.013712, -0.012051, -0.005326, 0.000560, 0.005300, 0.007429, 0.009930, 0.015968, 0.016454, 0.012383, 0.010385, 0.011612, 0.011413, 0.008357, 0.006831, 0.005524, 0.003087, 0.003507, 0.009876, 0.018892
	-0.017331, -0.015238, -0.021971, -0.024651, -0.029507, -0.040209, -0.044232, -0.046101, -0.052689, -0.053151, -0.047133, -0.042985, -0.040475, -0.037020, -0.029999, -0.021348, -0.018232, -0.017876, -0.013058, -0.008535, -0.013279, -0.011527, -0.006296, -0.001615, 0.002270, 0.006991, 0.010272, 0.013407, 0.015950, 0.012503, 0.008026, 0.013701, 0.011513, 0.004867, 0.010667, 0.006774, 0.003571, 0.012416, 0.004875, 0.020961
	-0.022637, -0.011107, -0.018340, -0.023896, -0.028320, -0.038092, -0.041212, -0.041642, -0.044537, -0.046015, -0.041699, -0.035805, -0.033527, -0.030911, -0.022925, -0.010175, -0.007279, -0.008644, -0.005065, -0.000597, -0.003797, -0.004052, 0.000635, 0.006175, 0.010857, 0.012993, 0.016956, 0.022765, 0.023298, 0.020262, 0.018285, 0.019467, 0.021161, 0.018785, 0.017891, 0.017817, 0.013874, 0.012825, 0.015904, 0.025844
	-0.014532, -0.010189, -0.019385, -0.022584, -0.028159, -0.037803, -0.040566, -0.038125, -0.040339, -0.038899, -0.033171, -0.028143, -0.025641, -0.019755, -0.012463, -0.003824, -0.000871, -0.002698, -0.000197, 0.001952, -0.001353, -0.000188, 0.004902, 0.012600, 0.014373, 0.016449, 0.018872, 0.022822, 0.026385, 0.020681, 0.015275, 0.021387, 0.023535, 0.016733, 0.022161, 0.018819, 0.011276, 0.020785, 0.014683, 0.032409
	-0.016972, -0.004835, -0.015539, -0.019706, -0.022971, -0.032222, -0.037732, -0.035551, -0.033892, -0.031679, -0.024624, -0.019946, -0.016412, -0.010040, -0.003445, 0.005991, 0.008364, 0.006410, 0.008289, 0.009260, 0.007409, 0.008691, 0.015230, 0.022729, 0.025465, 0.025502, 0.026102, 0.030309, 0.031861, 0.026963, 0.024651, 0.027000, 0.029039, 0.025577, 0.027217, 0.027660, 0.023245, 0.021705, 0.026383, 0.034120
	-0.007042, -0.003943, -0.013314, -0.016082, -0.020497, -0.030911, -0.035096, -0.030889, -0.029351, -0.025337, -0.018980, -0.012449, -0.008879, -0.001902, 0.003577, 0.011256, 0.012460, 0.010502, 0.011904, 0.011483, 0.010067, 0.013356, 0.020792, 0.027368, 0.026382, 0.028554, 0.028164, 0.029993, 0.033232, 0.028830, 0.022354, 0.027991, 0.029607, 0.020011, 0.031066, 0.031755, 0.025061, 0.037228, 0.024607, 0.041453
	-0.012463, -0.000987, -0.008994, -0.014815, -0.017487, -0.026372, -0.031392, -0.028459, -0.025402, -0.024153, -0.015566, -0.007862, -0.004579, 0.001484, 0.010757, 0.017401, 0.019536, 0.016264, 0.016278, 0.018231, 0.018193, 0.018217, 0.025442, 0.034794, 0.036179, 0.034770, 0.033985, 0.040104, 0.040404, 0.034161, 0.030977, 0.032380, 0.034144, 0.031909, 0.033231, 0.035957, 0.034171, 0.033050, 0.038776, 0.042972
	-0.002758, 0.000700, -0.008467, -0.011525, -0.018705, -0.027522, -0.031609, -0.027494, -0.026315, -0.023221, -0.014164, -0.006562, -0.002205, 0.006453, 0.013689, 0.018647, 0.017673, 0.016751, 0.017380, 0.018782, 0.019038, 0.021992, 0.027475, 0.034748, 0.036870, 0.036635, 0.035394, 0.037519, 0.038008, 0.032063, 0.025834, 0.030409, 0.033142, 0.023991, 0.034882, 0.034323, 0.030317, 0.042711, 0.030793, 0.045129
	-0.011501, 0.004979, -0.003199, -0.009532, -0.013737, -0.022490, -0.028056, -0.025047, -0.023987, -0.021727, -0.011113, -0.003633, 0.003070, 0.010580, 0.020230, 0.025058, 0.026653, 0.024592, 0.024567, 0.025613, 0.027386, 0.029282, 0.037705, 0.042901, 0.046601, 0.045443, 0.044217, 0.048155, 0.045715, 0.039788, 0.034981, 0.038594, 0.038594, 0.034532, 0.038671, 0.042065, 0.040659, 0.042101, 0.045919, 0.050030
	-0.005239, 0.006624, -0.001837, -0.005350, -0.012024, -0.022230, -0.026144, -0.022704, -0.021559, -0.017450, -0.008515, 0.000433, 0.007392, 0.014546, 0.023538, 0.029043, 0.029892, 0.027280, 0.028785, 0.030662, 0.032758, 0.032649, 0.040035, 0.046372, 0.048654, 0.050330, 0.049538, 0.049746, 0.048851, 0.041068, 0.034598, 0.041375, 0.041379, 0.030621, 0.043091, 0.044712, 0.038634, 0.053475, 0.042814, 0.059369
	-0.011843, 0.005417, 0.000007, -0.005709, -0.011391, -0.019100, -0.024151, -0.021274, -0.019356, -0.016953, -0.004422, 0.002891, 0.010688, 0.018353, 0.027665, 0.035281, 0.036655, 0.034937, 0.036795, 0.039994, 0.042705, 0.042668, 0.048600, 0.055673, 0.059602, 0.061002, 0.059934, 0.064283, 0.061835, 0.052838, 0.048644, 0.048401, 0.048158, 0.044262, 0.049173, 0.053313, 0.050054, 0.051718, 0.058112, 0.062677
	-0.003249, 0.007140, -0.000190, -0.005182, -0.010664, -0.017472, -0.021072, -0.018928, -0.015929, -0.011810, -0.001170, 0.006999, 0.014346, 0.022026, 0.033087, 0.037703, 0.039304, 0.038986, 0.040531, 0.042739, 0.044912, 0.045850, 0.052980, 0.060894, 0.062495, 0.065477, 0.066306, 0.069035, 0.066301, 0.058359, 0.048879, 0.054660, 0.053906, 0.042834, 0.051292, 0.054304, 0.049390, 0.064968, 0.053062, 0.067337
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 80.0
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 130, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 123, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 112, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 1766, in load_config
    return BedMesh(config)
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 107, in __init__
    self.splitter = MoveSplitter(config, self.gcode)
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 1259, in __init__
    self.split_delta_z = config.getfloat(
  File "/home/pi/klipper/klippy/configfile.py", line 70, in getfloat
    return self._get_wrapper(self.fileconfig.getfloat, option, default,
  File "/home/pi/klipper/klippy/configfile.py", line 49, in _get_wrapper
    raise error("Option '%s' in section '%s' must have minimum of %s"
configparser.Error: Option 'split_delta_z' in section 'bed_mesh' must have minimum of 0.01
webhooks client 4122453376: New connection
webhooks client 4122453376: Client info {'program': 'Moonraker', 'version': 'v0.9.3-0-g71f9e67'}
Attempting MCU 'mcu' reset
Unable to issue reset command on MCU 'rpi'
Attempting MCU 'toolboard_t0' reset
Attempting MCU 'toolboard_t1' reset
Attempting MCU 'dinghy' reset
Attempting MCU 'plasma' reset
webhooks client 4122453376: Disconnected
Restarting printer
Start printer at Tue Mar 17 04:08:21 2026 (1773720501.5 10105.9)
===== Config file =====
[mcu rpi]
serial = /tmp/klipper_host_mcu

[board_pins btt-octopus-pro-h723-11]
aliases = 
	
	
	
	x_step_pin=PF13,
	x_dir_pin=PF12,
	x_enable_pin=PF14,
	x_uart_pin=PC4,
	x_diag_pin=PG6,
	x_endstop_pin=PG6,
	
	
	
	dual_carriage_step_pin=PF9,
	dual_carriage_dir_pin=PF10,
	dual_carriage_enable_pin=PG2,
	dual_carriage_uart_pin=PF2,
	dual_carriage_diag_pin=PG12,
	dual_carriage_endstop_pin=PG12,
	
	
	
	y_step_pin=PG0,
	y_dir_pin=PG1,
	y_enable_pin=PF15,
	y_uart_pin=PD11,
	y_diag_pin=PG9,
	y_endstop_pin=PG9,
	
	
	
	y1_step_pin=PG4,
	y1_dir_pin=PC1,
	y1_enable_pin=PA2,
	y1_uart_pin=PC7,
	y1_diag_pin=PG11,
	y1_endstop_pin=PG11,
	
	
	
	z0_step_pin=PC13,
	z0_dir_pin=PF0,
	z0_enable_pin=PF1,
	z0_uart_pin=PE4,
	z0_diag_pin=PG13,
	
	
	
	z1_step_pin=PE2,
	z1_dir_pin=PE3,
	z1_enable_pin=PD4,
	z1_uart_pin=PE1,
	z1_diag_pin=PG14,
	
	
	
	z2_step_pin=PE6,
	z2_dir_pin=PA14,
	z2_enable_pin=PE0,
	z2_uart_pin=PD3,
	z2_diag_pin=PG15,
	
	e_step_pin=PF11,
	e_dir_pin=PG3,
	e_enable_pin=PG5,
	e_uart_pin=PC6,
	
	e_heater_pin=PA2,
	e_sensor_pin=PF4,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=PA7,
	stepper_spi_miso_pin=PA6,
	stepper_spi_sclk_pin=PA5,
	adxl345_cs_pin=PA15,
	bltouch_sensor_pin=PB7,
	bltouch_control_pin=PB6,
	probe_pin=PB7,
	fan_part_cooling_pin=PA8,
	fan_toolhead_cooling_pin=PE5,
	fan_controller_board_pin=PD12,
	heater_bed_heating_pin=PA1,
	heater_bed_sensor_pin=PF3,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PG15,
	filament_sensor_motion_pin=PG14,
	ratrig_vaoc_probe_pin=PG10,
	ratrig_vaoc_led_pin=PB0,
	ratrig_vaoc_fan_pin=PD13,
	chamber_lighting_pin=PB11,
	chamber_filter_4p_fan_pin=PD14,
	chamber_filter_4p_fan_enable_pin=PD15

[mcu]
serial = /dev/RatOS/btt-octopus-pro-h723-11

[temperature_sensor Octopus_Pro_H723_V1.1]
sensor_type = temperature_mcu

[adxl345 controlboard]
cs_pin = PA15
spi_software_mosi_pin = PB5
spi_software_miso_pin = PB4
spi_software_sclk_pin = PB3

[board_pins toolboard_t0]
mcu = toolboard_t0
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t0]
serial = /dev/RatOS/btt-ebb42-gen2-10-t0

[temperature_sensor EBB42_Gen2_v1.0_T0]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t0

[lis2dw toolboard_t0]
axes_map = x, z, y
cs_pin = toolboard_t0:PB1
spi_software_mosi_pin = toolboard_t0:PB11
spi_software_miso_pin = toolboard_t0:PB2
spi_software_sclk_pin = toolboard_t0:PB10

[board_pins toolboard_t1]
mcu = toolboard_t1
aliases = 
	
	e_step_pin=PD3,
	e_dir_pin=PD2,
	e_enable_pin=PB6,
	e_uart_pin=PB3,
	
	e_heater_pin=PB0,
	e_sensor_pin=PA1,
	e_power_draw_pin=null,
	stepper_spi_mosi_pin=null,
	stepper_spi_miso_pin=null,
	stepper_spi_sclk_pin=null,
	adxl345_cs_pin=PB1,
	bltouch_sensor_pin=PA5,
	bltouch_control_pin=PA4,
	probe_pin=PA5,
	fan_part_cooling_pin=PB8,
	fan_toolhead_cooling_pin=PB4,
	fan_controller_board_pin=null,
	heater_bed_heating_pin=null,
	heater_bed_sensor_pin=null,
	4p_fan_part_cooling_pin=null,
	4p_fan_part_cooling_tach_pin=null,
	4p_fan_part_cooling_enable_pin=null,
	4p_toolhead_cooling_pin=null,
	4p_toolhead_cooling_tach_pin=null,
	4p_controller_board_pin=null,
	4p_controller_board_tach_pin=null,
	run_led_pin=null,
	rgb_led_data_pin=null,
	filament_sensor_runout_pin=PA3,
	filament_sensor_motion_pin=PA9,
	ratrig_vaoc_probe_pin=null,
	ratrig_vaoc_led_pin=null,
	ratrig_vaoc_fan_pin=null,
	chamber_lighting_pin=null,
	chamber_filter_4p_fan_pin=null,
	chamber_filter_4p_fan_enable_pin=null

[mcu toolboard_t1]
serial = /dev/RatOS/btt-ebb42-gen2-10-t1

[temperature_sensor EBB42_Gen2_v1.0_T1]
sensor_type = temperature_mcu
sensor_mcu = toolboard_t1

[lis2dw toolboard_t1]
axes_map = x, z, y
cs_pin = toolboard_t1:PB1
spi_software_mosi_pin = toolboard_t1:PB11
spi_software_miso_pin = toolboard_t1:PB2
spi_software_sclk_pin = toolboard_t1:PB10

[gcode_macro RatOS]
variable_homing = "endstops"
variable_z_probe = "static"
variable_sensorless_x_current = 0.6
variable_sensorless_y_current = 0.9
variable_safe_home_x = "middle"
variable_safe_home_y = "middle"
variable_driver_type_x = "tmc2209"
variable_driver_type_y = "tmc2209"
variable_stowable_probe_stop_on_error = False
variable_chamber_filter_enable = True
variable_chamber_filter_speed = 0.5
variable_chamber_filter_disable_speed = 1.0
variable_chamber_filter_enable_at = "after_print_start"
variable_chamber_filter_disable_period = 300
variable_chamber_filter_disable_bed_temp = 0
variable_chamber_heater_enable = True
variable_chamber_heater_bed_temp = 115
variable_chamber_heater_preheating_temp = 150
variable_chamber_heater_heating_temp_offset = 25
variable_chamber_heater_control_external_heater = False
variable_chamber_heater_air_circulation_enable = True
variable_chamber_heater_air_circulation_fan_speed = 0.35
variable_chamber_heater_air_circulation_y_pos = 0
variable_chamber_heater_air_circulation_z_pos = 100
variable_chamber_heater_extra_fan_speed = 1.0
variable_chamber_heater_filter_fan_speed = 1.0
variable_bed_heat_soak_time = 0
variable_hotend_heat_soak_time = 0
variable_led_status_action = 0.0,1.0,1.0
variable_led_status_success = 0.0,1.0,0.0
variable_led_status_error = 1.0,0.0,1.0
variable_led_status_on = 1.0,1.0,1.0
variable_led_status_off = 0.0,0.0,1.0
variable_led_status_standby = 0.1,0.1,0.1
variable_led_status_heating = 1.0,0.0,0.0
variable_led_status_cooling = 0.0,0.0,1.0
variable_calibrate_bed_mesh = True
variable_adaptive_mesh = True
variable_start_print_park_in = "center"
variable_start_print_park_z_height = 3
variable_end_print_park_in = "back"
variable_pause_print_park_in = "back"
variable_end_print_park_z_hop = 20
variable_nozzle_priming = "primeblob"
variable_nozzle_prime_start_x = "max"
variable_nozzle_prime_start_y = "min"
variable_nozzle_prime_direction = "auto"
variable_nozzle_prime_bridge_fan = 102
variable_probe_for_priming_result = None
variable_probe_for_priming_end_result = None
variable_probe_for_priming_result_t1 = None
variable_probe_for_priming_end_result_t1 = None
variable_probe_for_priming_disable_mesh_constraints = False
variable_adaptive_prime_offset_threshold = -1.0
variable_last_z_offset = None
variable_runout_park_in = "front"
variable_enable_unload_tip_forming = False
variable_filament_unload_length = 150
description = RatOS variable storage macro, will echo variables to the console when run.
variable_relative_extrusion = True
variable_force_absolute_position = False
variable_preheat_extruder = True
variable_preheat_extruder_temp = 150
variable_macro_travel_speed = 600
variable_macro_travel_accel = 8000
variable_macro_z_speed = 15
variable_bed_margin_x = [59.6, 59.6]
variable_bed_margin_y = [14.35, 33.65]
variable_printable_x_min = 0
variable_printable_x_max = 0
variable_printable_y_min = 0
variable_printable_y_max = 0
variable_end_print_motors_off = True
variable_status_color_ok = "00FF00"
variable_status_color_error = "FF0000"
variable_status_color_unknown = "FFFF00"
variable_end_print_retract_filament = 10
gcode = 
	ECHO_RATOS_VARS
variable_auto_center_subject = False
variable_toolchange_zhop = 2.0
variable_toolchange_zspeed = 25
variable_toolchange_sync_fans = False
variable_toolchange_combined_zhop = False
variable_toolchange_travel_speed = 600
variable_toolchange_travel_accel = 8000
variable_toolchange_extrusion = 2.0
variable_toolchange_retraction = 2.0
variable_toolchange_feedrate = 7200
variable_toolchange_prepurging_timer = 0
variable_toolchange_standby_temp = -1
variable_toolchange_purge = 25
variable_toolchange_first_purge = 50
variable_beacon_bed_mesh_scv = 25
variable_beacon_contact_z_homing = False
variable_beacon_contact_start_print_true_zero = True
variable_beacon_contact_start_print_true_zero_fuzzy_position = True
variable_beacon_contact_calibrate_model_on_true_zero = True
variable_beacon_contact_wipe_before_true_zero = True
variable_beacon_contact_wipe_before_true_zero_method = "probe_clean"
variable_beacon_contact_true_zero_temp = 170
variable_beacon_contact_prime_probing = True
variable_beacon_contact_expansion_compensation = True
variable_beacon_contact_bed_mesh = False
variable_beacon_contact_bed_mesh_samples = 2
variable_beacon_contact_z_tilt_adjust = False
variable_beacon_contact_z_tilt_adjust_samples = 2
variable_beacon_scan_compensation_enable = True
variable_beacon_scan_compensation_profile = "auto"
variable_beacon_scan_compensation_desired_spacing = 10
variable_beacon_scan_compensation_bed_temp_mismatch_is_error = False
variable_beacon_contact_poke_bottom_limit = -1
variable_beacon_scan_method_automatic = False
variable_beacon_adaptive_heat_soak = True
variable_beacon_adaptive_heat_soak_max_wait = 5400
variable_beacon_adaptive_heat_soak_extra_wait_after_completion = 0
variable_beacon_adaptive_heat_soak_layer_quality = 3
variable_beacon_adaptive_heat_soak_maximum_first_layer_duration = 1800
variable_beacon_contact_start_print_true_zero_fuzzy_radius = 20
variable_homing_x = "endstop"
variable_homing_y = "endstop"
variable_default_toolhead = 0
variable_adxl_chip = ["lis2dw toolboard_t0", "lis2dw toolboard_t1"]
variable_shaper_x_freq = [54.2, 53.2, 53.6, 54.4]
variable_shaper_y_freq = [40.8, 47.6, 38.6, 38]
variable_shaper_x_type = ["mzv", "mzv", "mzv", "mzv"]
variable_shaper_y_type = ["mzv", "mzv", "mzv", "mzv"]
variable_x_driver_types = ["tmc5160"]
variable_x_axes = ["x"]
variable_y_driver_types = ["tmc5160", "tmc5160"]
variable_y_axes = ["y", "y1"]
variable_z_driver_types = ["tmc2209", "tmc2209", "tmc2209"]
variable_z_axes = ["z", "z1", "z2"]
variable_home_y_first = True

[ratos_homing]
axes = xyz
z_hop = 15
z_hop_speed = 15
gcode = 
	
	_LED_ON
	
	
	{% set prev_stop_on_error = printer["gcode_macro RatOS"].stowable_probe_stop_on_error %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set target_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	_IDEX_SINGLE
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE=True
	
	
	M400
	
	G90
	
	
	{% set X = true if params.X is defined else false %}
	{% set Y = true if params.Y is defined else false %}
	{% set Z = true if params.Z is defined else false %}
	{% if printer["gcode_macro RatOS"].home_y_first|default(false)|lower == 'true' %}
	HOME_Y X={X} Y={Y} Z={Z}
	HOME_X X={X} Y={Y} Z={Z}
	{% else %}
	HOME_X X={X} Y={Y} Z={Z}
	HOME_Y X={X} Y={Y} Z={Z}
	{% endif %}
	HOME_Z X={X} Y={Y} Z={Z}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=stowable_probe_stop_on_error VALUE={prev_stop_on_error}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[gcode_macro HOME_X]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_x = printer["gcode_macro RatOS"].homing_x|lower %}
	{% set homing_x = homing_x if homing_x else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_X" MSG="printable_x_max: {printable_x_max}, safe_home_x: {safe_home_x}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}"
	
	
	{% if X or not Y and not Z %}
	{% if homing_x == 'endstop' %}
	G28 X
	{% elif homing_x == 'sensorless' %}
	{% if printer["dual_carriage"] is defined %}
	{ action_emergency_stop("sensorless homing not supported on IDEX!") }
	{% endif %}
	HOME_X_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_x to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_x, homing)) }
	{% endif %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1} MODE=PRIMARY
	G1 X{parking_position} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	{% endif %}
	{% set x_homed = True %}
	G0 X{safe_home_x} F{speed}
	M400
	{% endif %}

[gcode_macro HOME_Y]
gcode = 
	
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set homing = printer["gcode_macro RatOS"].homing|lower %}
	{% set homing_y = printer["gcode_macro RatOS"].homing_y|lower %}
	{% set homing_y = homing_y if homing_y else homing %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Y" MSG="printable_y_max: {printable_y_max}, safe_home_y: {safe_home_y}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}"
	
	
	{% if Y or not X and not Z %}
	{% if homing_y == 'endstop' %}
	G28 Y
	{% elif homing_y == 'sensorless' %}
	HOME_Y_SENSORLESS
	{% else %}
	{ action_emergency_stop("expected RatOS variable_homing_y to be 'sensorless' 'endstop' or variable_homing to be 'sensorless' or 'endstops' but found {} and {}".format(homing_y, homing)) }
	{% endif %}
	{% set y_homed = True %}
	G0 Y{safe_home_y} F{speed}
	{% endif %}

[gcode_macro HOME_Z]
gcode = 
	
	{% set x_homed = 'x' in printer.toolhead.homed_axes %}
	{% set y_homed = 'y' in printer.toolhead.homed_axes %}
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	
	
	{% set beacon_contact_z_homing = true if printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_z_home_position_fuzzing_radius = printer["gcode_macro RatOS"].beacon_z_home_position_fuzzing_radius|default(0)|float %}
	
	
	{% set X = true if params.X|lower == 'true' else false %}
	{% set Y = true if params.Y|lower == 'true' else false %}
	{% set Z = true if params.Z|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="HOME_Z" MSG="x_homed: {x_homed}, y_homed: {y_homed}, z_probe: {z_probe}, beacon_contact_z_homing: {beacon_contact_z_homing}"
	
	
	{% if Z or not Y and not X %}
	RATOS_ECHO MSG="Homing Z"
	{% if x_homed == False or y_homed == False %}
	{ action_emergency_stop("X and Y must be homed before homing Z") }
	{% else %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_homing %}
	{% if beacon_contact_start_print_true_zero %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% else %}
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	{% else %}
	G28 Z
	{% endif %}
	_Z_HOP
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro HOME_X_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_x_current}
	{% endif %}
	
	
	G4 P300
	
	G28 X
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_x_sensorless"

[gcode_macro HOME_Y_SENSORLESS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	M204 S1000
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer["gcode_macro RatOS"].sensorless_y_current}
	{% endif %}
	
	
	G4 P300
	
	G28 Y
	
	
	{% if printer["gcode_macro RatOS"].x_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].x_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].x_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set x_driver = printer["gcode_macro RatOS"].driver_type_x|lower ~ " stepper_x" %}
	SET_TMC_CURRENT STEPPER=stepper_x CURRENT={printer.fastconfig.config[x_driver].run_current}
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].y_axes is defined %}
	{% for axis in printer["gcode_macro RatOS"].y_axes %}
	{% set stepper = "stepper_" ~ axis|lower %}
	{% set stepper_driver = printer["gcode_macro RatOS"].y_driver_types[loop.index0] ~ " " ~ stepper %}
	SET_TMC_CURRENT STEPPER={stepper} CURRENT={printer.fastconfig.config[stepper_driver].run_current}
	{% endfor %}
	{% else %}
	{% set y_driver = printer["gcode_macro RatOS"].driver_type_y|lower ~ " stepper_y" %}
	SET_TMC_CURRENT STEPPER=stepper_y CURRENT={printer.fastconfig.config[y_driver].run_current}
	{% endif %}
	
	
	G4 P300
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="home_y_sensorless"

[gcode_macro _Z_HOP]
description = Move Z axis up by Z_HOP distance at Z_HOP_SPEED. In relative mode it will move Z axis up by Z_HOP distance. In absolute mode it will move Z axis to Z_HOP distance.
gcode = 
	{% set z_hop = printer.fastconfig.config.ratos_homing.z_hop|float %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	G0 Z{z_hop} F{z_hop_speed}

[gcode_macro __MOVE_TO_SAFE_Z_HOME_ECHO_DEBUG]
gcode = 
	DEBUG_ECHO PREFIX="_MOVE_TO_SAFE_Z_HOME" MSG="x: {params.X}, y: {params.Y}, z_hop: {params.Z_HOP}, fuzzy_radius: {params.FUZZY_RADIUS}, axis_maximum.x: {printer.toolhead.axis_maximum.x}, axis_maximum.y: {printer.toolhead.axis_maximum.y}, bed_margin_x: {printer['gcode_macro RatOS'].bed_margin_x}, bed_margin_y: {printer['gcode_macro RatOS'].bed_margin_y}, printable_x_max: {printer['gcode_macro RatOS'].printable_x_max}, printable_y_max: {printer['gcode_macro RatOS'].printable_y_max}"

[gcode_macro MAYBE_HOME]
description = Only home unhomed axis. Specify ABL=1 to also ensure that automatic bed levelling is applied (if configured).
variable_is_kinematic_position_overriden = False
gcode = 
	{% set abl = params.ABL|default('')|lower in ('true', 'yes', '1') %}
	{% if printer["gcode_macro MAYBE_HOME"].is_kinematic_position_overriden|lower == 'true' %}
	RATOS_ECHO MSG="SET_CENTER_KINEMATIC_POSITION has been abused. Homing all axes. Please refrain from using SET_CENTER_KINEMATIC_POSITION outside of debugging purposes."
	G28
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=False
	{% else %}
	{% set axes = '' %}
	{% set isHomed = true %}
	{% set axesToHome = '' %}
	{% if params.X is defined %}
	{% set axes = axes ~ 'X ' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% endif %}
	{% if params.Y is defined %}
	{% set axes = axes ~ 'Y ' %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% endif %}
	{% if params.Z is defined %}
	{% set axes = axes ~ 'Z ' %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if params.X is not defined and params.Y is not defined and params.Z is not defined %}
	{% set axes = '' %}
	{% if 'x' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'X ' %}
	{% endif %}
	{% if 'y' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Y ' %}
	{% endif %}
	{% if 'z' not in printer.toolhead.homed_axes %}
	{% set isHomed = false %}
	{% set axesToHome = axesToHome ~ 'Z ' %}
	{% endif %}
	{% endif %}
	{% if isHomed is false %}
	RATOS_ECHO MSG="Homing {axesToHome}"
	G28 {axesToHome}
	{% else %}
	RATOS_ECHO MSG="All requested axes already homed. Skipping homing."
	{% endif %}
	{% endif %}
	{% if abl %}
	{% if printer.z_tilt is defined %}
	{% if not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Performing Z tilt adjustment..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Z tilt already applied. Skipping Z tilt adjustment."
	{% endif %}
	{% elif printer.quad_gantry_level is defined %}
	{% if not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Performing quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% else %}
	RATOS_ECHO MSG="Quad gantry leveling already applied. Skipping quad gantry leveling."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="No automatic bed leveling method configured. Skipping bed leveling."
	{% endif %}
	{% endif %}

[gcode_macro PID_CALIBRATE_HOTEND]
description = Perform a PID calibration test for a given extruder heater.
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set temp = params.TEMP|default(220)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_HOTEND" MSG="TEMP={temp}"
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO MSG="PID calibration hotend heater T0 at {temp}°C..."
	PID_CALIBRATE HEATER=extruder TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	
	{% if toolhead==0 or toolhead==1 %}
	RATOS_ECHO MSG="PID calibration hotend heater T{toolhead} at {temp}°C..."
	PID_CALIBRATE HEATER=extruder{'' if toolhead==0 else toolhead} TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_BED]
description = Perform a PID calibration test for the bed heater.
gcode = 
	
	{% set temp = params.TEMP|default(80)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_BED" MSG="TEMP={temp}"
	RATOS_ECHO MSG="PID calibration bed heater at {temp}°C..."
	
	
	PID_CALIBRATE HEATER=heater_bed TARGET={temp}
	
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION

[gcode_macro PID_CALIBRATE_CHAMBER_HEATER]
description = Perform a PID calibration test for the chamber heater.
gcode = 
	
	{% set temp = params.TEMP|default(150)|int %}
	
	DEBUG_ECHO PREFIX="PID_CALIBRATE_CHAMBER_HEATER" MSG="TEMP={temp}"
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	RATOS_ECHO MSG="PID calibration chamber heater at {temp}°C..."
	PID_CALIBRATE HEATER=chamber_heater TARGET={temp}
	_CONSOLE_SAVE_CONFIG
	_LEARN_MORE_CALIBRATION
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_heater" %}
	{% set link_text = "RatOS Chamber Heater" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber heater found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro INITIALIZE_PA_TUNING]
description = Start a pressure advance tuning tower.
gcode = 
	
	{% set start = params.START|default(0.0)|float %}
	{% set factor = params.FACTOR|default(0.001)|float %}
	
	
	{% set layer_number = printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|default(0)|int %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if is_printing_gcode and layer_number < 2 %}
	DEBUG_ECHO PREFIX="START_PA_TOWER" MSG="START: {start}, FACTOR: {factor}"
	RATOS_ECHO MSG="Starting pressure advance tuning tower..."
	TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START={start} FACTOR={factor}
	{% else %}
	RATOS_ECHO MSG="Pressure advance tuning tower requires you to be printing gcode and on layer 1 to start."
	{% endif %}
	
	_LEARN_MORE_CALIBRATION

[gcode_macro CHAMBER_FILTER_ON]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	_CHAMBER_FILTER_TURN_ON
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro CHAMBER_FILTER_OFF]
gcode = 
	{% if printer["fan_generic filter"] is defined %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Deactivating chamber filter..."
	_CHAMBER_FILTER_TURN_OFF
	{% else %}
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="No chamber filter found" TYPE="warning" MSG={line_1}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set chamber_filter_enable_at = printer["gcode_macro RatOS"].chamber_filter_enable_at|default('after_print_start')|lower %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_ON" MSG="at: {at}, chamber_filter_enable: {chamber_filter_enable}, chamber_filter_enable_at: {chamber_filter_enable_at}, chamber_filter_speed: {chamber_filter_speed}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	{% if chamber_filter_enable_at == at %}
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Activating chamber filter..."
	
	
	_CHAMBER_FILTER_TURN_ON AT={at}
	
	
	{% if chamber_filter_enable_at == "print_end" %}
	_LED_CHAMBER_FILTER_ON
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_FILTER_OFF]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF" MSG="chamber_filter_enable: {chamber_filter_enable}, filter_disable_period: {filter_disable_period}, filter_disable_bed_temp: {filter_disable_bed_temp}"
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	
	{% if filter_disable_period > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting {filter_disable_period} seconds before turning chamber filter off..."
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION={filter_disable_period}
	{% endif %}
	
	
	{% if filter_disable_bed_temp > 0 %}
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Waiting for bed temp to cool down to {filter_disable_bed_temp}°C to turn filter off..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM=0 MAXIMUM={filter_disable_bed_temp}
	_CHAMBER_FILTER_TURN_OFF
	_LED_CHAMBER_FILTER_OFF
	{% endif %}
	
	{% endif %}

[delayed_gcode _CHAMBER_FILTER_OFF_TIMER]
gcode = 
	DEBUG_ECHO PREFIX="_CHAMBER_FILTER_OFF_TIMER" MSG="executed"
	
	
	_CHAMBER_FILTER_TURN_OFF
	
	
	RATOS_ECHO PREFIX="CHAMBER_FILTER" MSG="Chamber filter turned off!"
	
	
	_LED_CHAMBER_FILTER_OFF

[gcode_macro _CHAMBER_FILTER_TURN_ON]
gcode = 
	
	{% set at = params.AT|default('')|lower %}
	
	
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_speed|default(0)|float %}
	{% if at == "print_end" %}
	{% set chamber_filter_speed = printer["gcode_macro RatOS"].chamber_filter_disable_speed|default(0)|float %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_FILTER_OFF_TIMER DURATION=0
	
	
	SET_FAN_SPEED FAN=filter SPEED={chamber_filter_speed}

[gcode_macro _CHAMBER_FILTER_TURN_OFF]
gcode = 
	
	SET_FAN_SPEED FAN=filter SPEED=0

[gcode_macro _CHAMBER_FILTER_SANITY_CHECK]
gcode = 
	
	{% set chamber_filter_enable = true if printer["gcode_macro RatOS"].chamber_filter_enable|default(true)|lower == 'true' else false %}
	{% set filter_disable_period = printer["gcode_macro RatOS"].chamber_filter_disable_period|default(0)|int %}
	{% set filter_disable_bed_temp = printer["gcode_macro RatOS"].chamber_filter_disable_bed_temp|default(0)|int %}
	
	
	{% if chamber_filter_enable and printer["fan_generic filter"] is defined %}
	
	{% if filter_disable_bed_temp > 0 and filter_disable_period > 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable, not both.")}
	{% endif %}
	
	{% if filter_disable_bed_temp == 0 and filter_disable_period == 0 %}
	_LEARN_MORE_CHAMBER_FILTER
	{action_respond_info("Wrong chamber filter options configured! Set 'filter_disable_bed_temp' or 'filter_disable_period' variable.")}
	{% endif %}
	
	{% endif %}

[gcode_macro CHAMBER_HEATER_ON]
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(45)|int %}
	
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp} IS_FROM_START_PRINT=False

[gcode_macro CHAMBER_HEATER_OFF]
gcode = 
	_CHAMBER_HEATER_OFF

[gcode_macro _CHAMBER_HEATER_ON]
variable_chamber_temp = 0
gcode = 
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	{% set is_from_start_print = true if params.IS_FROM_START_PRINT|default(True)|lower == 'true' else false %}
	
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set chamber_heater_enable = true if printer["gcode_macro RatOS"].chamber_heater_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}
	{% set chamber_heater_preheating_temp = printer["gcode_macro RatOS"].chamber_heater_preheating_temp|default(150)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	{% set chamber_heater_control_external_heater = true if printer["gcode_macro RatOS"].chamber_heater_control_external_heater|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_enable = true if printer["gcode_macro RatOS"].chamber_heater_air_circulation_enable|default(true)|lower == 'true' else false %}
	{% set chamber_heater_air_circulation_fan_speed = printer["gcode_macro RatOS"].chamber_heater_air_circulation_fan_speed|default(0.35)|float %}
	{% set chamber_heater_air_circulation_y_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_y_pos|default(0)|float %}
	{% set chamber_heater_air_circulation_z_pos = printer["gcode_macro RatOS"].chamber_heater_air_circulation_z_pos|default(100)|float %}
	
	DEBUG_ECHO PREFIX="_CHAMBER_HEATER_ON" MSG="chamber_heater_enable: {chamber_heater_enable}, chamber_heater_preheating_temp: {chamber_heater_preheating_temp}, chamber_heater_heating_temp_offset: {chamber_heater_heating_temp_offset}, bed_temp: {bed_temp}, chamber_temp: {chamber_temp}, start_chamber_temp: {start_chamber_temp}"
	
	
	{% if chamber_heater_enable and chamber_temp > 0 and chamber_heater_bed_temp > 0 %}
	
	
	_LED_HEATING
	
	
	RATOS_ECHO MSG="Preheating chamber to {(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}°C..."
	
	
	{% set chamber_temp_sensor = "extruder" %}
	{% if printer["dual_carriage"] is defined and default_toolhead == 1 %}
	{% set chamber_temp_sensor = "extruder1" %}
	{% endif %}
	{% if printer["temperature_sensor chamber"] is defined %}
	{% set chamber_temp_sensor = "temperature_sensor chamber" %}
	{% endif %}
	
	
	{% set current_chamber_temp = printer['%s' % chamber_temp_sensor].temperature|int %}
	
	
	{% set needs_heating = current_chamber_temp < (start_chamber_temp if start_chamber_temp > 0 else chamber_temp) %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_BEFORE_PREHEATING
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	{% if not is_from_start_print %}
	MAYBE_HOME
	{% endif %}
	G0 Z{chamber_heater_air_circulation_z_pos} F{z_speed}
	G0 Y{chamber_heater_air_circulation_y_pos} F{speed}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={chamber_heater_air_circulation_fan_speed if default_toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * chamber_heater_air_circulation_fan_speed)}
	{% endif %}
	{% else %}
	{% if is_from_start_print %}
	G0 Z{z} F{z_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE={chamber_temp}
	
	
	{% if needs_heating %}
	
	
	M140 S{chamber_heater_bed_temp}
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={chamber_heater_preheating_temp}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	
	{% endif %}
	
	
	{% if needs_heating %}
	_CHAMBER_HEATER_EXTRA_FAN_ON
	{% endif %}
	
	
	{% if needs_heating %}
	TEMPERATURE_WAIT SENSOR="{chamber_temp_sensor}" MINIMUM={(start_chamber_temp if start_chamber_temp > 0 else chamber_temp)}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% endif %}
	
	
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED=0
	_CHAMBER_FILTER_ON AT="before_print_start"
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	{% if chamber_heater_air_circulation_enable and chamber_heater_air_circulation_fan_speed > 0 %}
	G28 Z
	{% endif %}
	{% endif %}
	
	
	{% if needs_heating %}
	_USER_CHAMBER_HEATER_AFTER_PREHEATING
	{% endif %}
	
	
	{% if printer["temperature_sensor chamber"] is defined %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined and chamber_heater_control_external_heater %}
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	
	
	_LED_SUCCESS
	
	{% endif %}

[gcode_macro _CHAMBER_HEATER_OFF]
gcode = 
	RATOS_ECHO MSG="Deactivating chamber heater..."
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=0
	
	
	SET_GCODE_VARIABLE MACRO=_CHAMBER_HEATER_ON VARIABLE=chamber_temp VALUE=0
	
	
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	
	
	_CHAMBER_HEATER_EXTRA_FAN_OFF

[delayed_gcode _CHAMBER_HEATER_CONTROL]
initial_duration = 0.
gcode = 
	
	{% set chamber_temp = printer["gcode_macro _CHAMBER_HEATER_ON"].chamber_temp|default(0)|int %}
	{% set chamber_heater_heating_temp_offset = printer["gcode_macro RatOS"].chamber_heater_heating_temp_offset|default(20)|int %}
	
	
	{% set current_chamber_temp = printer['temperature_sensor chamber'].temperature|int %}
	
	
	{% if current_chamber_temp < chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET={(chamber_temp + chamber_heater_heating_temp_offset)}
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=1.0
	{% endif %}
	{% endif %}
	
	
	{% if current_chamber_temp >= chamber_temp %}
	{% if printer["heater_generic chamber_heater"] is defined %}
	SET_HEATER_TEMPERATURE HEATER=chamber_heater TARGET=0
	{% endif %}
	{% if printer["output_pin chamber_heater_pin"] is defined %}
	SET_PIN PIN=chamber_heater_pin VALUE=0.0
	{% endif %}
	{% endif %}
	
	
	UPDATE_DELAYED_GCODE ID=_CHAMBER_HEATER_CONTROL DURATION=5

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_ON]
gcode = 
	
	{% set chamber_heater_extra_fan_speed = printer["gcode_macro RatOS"].chamber_heater_extra_fan_speed|default(0.0)|float %}
	
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	{% if chamber_heater_extra_fan_speed > 0 %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED={chamber_heater_extra_fan_speed}
	{% endif %}
	{% endif %}

[gcode_macro _CHAMBER_HEATER_EXTRA_FAN_OFF]
gcode = 
	
	{% if printer["fan_generic chamber_heater_extra_fan"] is defined %}
	SET_FAN_SPEED FAN=chamber_heater_extra_fan SPEED=0
	{% endif %}

[gcode_macro _USER_CHAMBER_HEATER_BEFORE_PREHEATING]
description = Will be executed before chamber preheating, only if heating is needed.
gcode = 

[gcode_macro _USER_CHAMBER_HEATER_AFTER_PREHEATING]
description = Will be executed after chamber preheating, only if heating was needed.
gcode = 

[gcode_macro RESET_HEATSOAK_SETTINGS]
description = Resets all heatsoak-related settings to startup defaults
gcode = 
	HEATSOAK_SETTINGS ACTION=reset

[gcode_macro USE_ADAPTIVE_HEATSOAK]
description = Temporarily enables adaptive bed heatsoaking (if a beacon probe is present), will reset to printer.cfg settings
	when Klipper is restarted. Optionally specify QUALITY (1-5) and maximum FIRST_LAYER_DURATION (in minutes).
	Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.QUALITY|default("1..5") %}
	{% set _ = params.FIRST_LAYER_DURATION|default("1..120 minutes") %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("Adaptive heatsoaking is only available when a beacon probe is configured.") }
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_quality = (settings.variable_beacon_adaptive_heat_soak_layer_quality if defsrc == 'startup' else current.beacon_adaptive_heat_soak_layer_quality)|default(3)|int %}
	{% set default_first_layer_duration_secs = (settings.variable_beacon_adaptive_heat_soak_maximum_first_layer_duration if defsrc == 'startup' else current.beacon_adaptive_heat_soak_maximum_first_layer_duration)|default(1800)|int %}
	{% if params2.QUALITY is defined %}
	{% set quality = params2.QUALITY|int %}
	{% if quality < 1 or quality > 5 %}
	{ action_raise_error("QUALITY must be between 1 (rough) and 5 (maximum). Use 3 (normal) if unsure.") }
	{% endif %}
	{% else %}
	{% set quality = default_quality %}
	{% endif %}
	{% if params2.FIRST_LAYER_DURATION is defined %}
	{% set first_layer_duration_mins = params2.FIRST_LAYER_DURATION|float %}
	{% if first_layer_duration_mins <= 0 %}
	{ action_raise_error("FIRST_LAYER_DURATION must be a positive number specifying the maximum first layer duration in minutes.") }
	{% endif %}
	{% if first_layer_duration_mins > 120 %}
	CONSOLE_ECHO MSG="FIRST_LAYER_DURATION will be limited to 120 minutes. Values larger than this will not have an effect on soak time."
	{% set first_layer_duration_mins = 120 %}
	{% endif %}
	{% set first_layer_duration_secs = (first_layer_duration_mins * 60.0)|int %}
	{% else %}
	{% set first_layer_duration_secs = default_first_layer_duration_secs %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	{% endif %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=True beacon_adaptive_heat_soak_layer_quality={quality} beacon_adaptive_heat_soak_maximum_first_layer_duration={first_layer_duration_secs}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."

[gcode_macro USE_FIXED_HEATSOAK]
description = Temporarily enables fixed bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
	Optionally specify DURATION (in minutes). Startup settings will be used by default.
gcode = 
	
	{% set params2 = params %}
	{% if False %}
	{% set _ = params.DURATION|default("0..720 minutes") %}
	{% endif %}
	{% set settings = printer.fastconfig.settings["gcode_macro ratos"] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro RatOS]") }
	{% endif %}
	{% set defsrc = params2.DEFAULT|default(printer["gcode_macro HEATSOAK_SETTINGS"].default_source)|lower %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% if not defsrc in ('startup', 'current') %}
	{ action_raise_error("DEFAULT must be either 'startup' or 'current'.") }
	{% endif %}
	{% set default_duration = (settings.variable_bed_heat_soak_time if defsrc == 'startup' else current.bed_heat_soak_time)|default(0)|int %}
	{% if params2.DURATION is defined %}
	{% set duration_mins = params2.DURATION|float %}
	{% if duration_mins < 0 %}
	{ action_raise_error("DURATION must be a non-negative number specifying the heatsoak duration in minutes.") }
	{% endif %}
	{% if duration_mins > 720 %}
	CONSOLE_ECHO MSG="DURATION will be limited to 720 minutes (12 hours). If you really need a larger value, adjust printer.cfg instead."
	{% set duration_mins = 720 %}
	{% endif %}
	{% set duration_secs = (duration_mins * 60.0)|int %}
	{% else %}
	{% set duration_secs = default_duration %}
	{% set duration_mins = duration_secs / 60.0 %}
	{% endif %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% if has_beacon %}
	HEATSOAK_SETTINGS QUIET=1 beacon_adaptive_heat_soak=False bed_heat_soak_time={duration_secs}
	{% else %}
	HEATSOAK_SETTINGS QUIET=1 bed_heat_soak_time={duration_secs}
	{% endif %}
	{% if duration_mins < 1e-3 %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% else %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% endif %}

[gcode_macro USE_NO_HEATSOAK]
description = Temporarily disables bed heatsoaking, will reset to printer.cfg settings when Klipper is restarted.
gcode = 
	USE_FIXED_HEATSOAK DURATION=0

[gcode_macro HEATSOAK_SETTINGS]
description = Shows or adjusts heatsoak settings
	- With no arguments: shows current heatsoak settings, specify VERBOSE=1 for detailed output
	- With arguments: sets the specified settings. Use the full setting name without the variable_ prefix, e.g. bed_heat_soak_time=300 or beacon_adaptive_heat_soak_layer_quality=4. See printer.cfg for available settings.
variable_default_source = "startup"
gcode = 
	
	{% set params2 = params %}
	{% set has_beacon = printer.fastconfig.settings.beacon is defined %}
	{% set quiet = params2.pop("QUIET", None)|default("0") in ("1", "true", "yes") %}
	{% set verbose = params2.pop("VERBOSE", None)|default("0") in ("1", "true", "yes") %}
	{% if has_beacon %}
	{% set vars = (
	"beacon_adaptive_heat_soak",
	"beacon_adaptive_heat_soak_max_wait",
	"beacon_adaptive_heat_soak_extra_wait_after_completion",
	"beacon_adaptive_heat_soak_layer_quality",
	"beacon_adaptive_heat_soak_maximum_first_layer_duration",
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% else %}
	{% set vars = (
	"bed_heat_soak_time",
	"hotend_heat_soak_time",
	) %}
	{% endif %}
	{% set action = "show" if params|length == 0 else params2.ACTION %}
	{% if action is defined and params|length > 1 %}
	{ action_raise_error("ACTION cannot be specified with other parameters.") }
	{% elif action is not defined %}
	{% for k, v in params2.items() %}
	{% set k = k|lower %}
	{% if k in vars %}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Setting {k} to {v}"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={k} VALUE={v}
	{% else %}
	{ action_raise_error("Parameter '%s' is not recognised. Note that adaptive heatsoaking settings can only be set when a beacon probe is configured." % k) }
	{% endif %}
	{% endfor %}
	{% elif action == "reset" %}
	_RESET_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	CONSOLE_ECHO MSG="Heatsoak settings have been reset to their original values."
	{% elif action == "show" %}
	{% set current = printer["gcode_macro RatOS"] %}
	{% set is_adaptive = False if not has_beacon else current.beacon_adaptive_heat_soak|default("")|lower == "true" %}
	{% if is_adaptive %}
	{% set quality = current.beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set first_layer_duration_secs = current.beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	{% set first_layer_duration_mins = first_layer_duration_secs / 60.0 %}
	RATOS_ECHO MSG="Will use adaptive bed heatsoak with quality {quality} and maximum first layer duration of {first_layer_duration_mins|int if (first_layer_duration_mins|float).is_integer() else first_layer_duration_mins|round(2)} minutes."
	{% elif current.bed_heat_soak_time|default(0)|int > 0 %}
	{% set duration_mins = (current.bed_heat_soak_time|int / 60.0) %}
	RATOS_ECHO MSG="Will use fixed-duration bed heatsoak of {duration_mins|int if (duration_mins|float).is_integer() else duration_mins|round(2)} minutes."
	{% else %}
	RATOS_ECHO MSG="Will use no bed heatsoak."
	{% endif %}
	{% if verbose %}
	CONSOLE_ECHO MSG="Detailed settings:"
	_SHOW_GCODE_VARIABLES MACRO=RatOS VARIABLES={vars|join(',')} SKIP_UNDEFINED_VARIABLES=1
	{% endif %}
	{% else %}
	{ action_raise_error("Action '%s' is not recognised" % action) }
	{% endif %}

[gcode_macro _LED_START_PRINTING]
gcode = 
	_LED_ACTION

[gcode_macro _LED_START_PRINTING_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_PRINTING]
gcode = 
	_LED_ON TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_PAUSE]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_ON]
gcode = 
	_LED_ACTION

[gcode_macro _LED_CHAMBER_FILTER_OFF]
gcode = 
	_LED_STANDBY

[gcode_macro _LED_LOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_LOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_RUNOUT]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_CLOG]
gcode = 
	_LED_ERROR TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_UNLOADING_FILAMENT]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_FILAMENT_UNLOADED]
gcode = 
	_LED_SUCCESS TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_DEACTIVATE_TOOLHEAD]
gcode = 
	_LED_OFF TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_STANDBY]
gcode = 
	_LED_STANDBY TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_TOOLHEAD_WAKEUP]
gcode = 
	_LED_ACTION TOOLHEAD={params.TOOLHEAD|default(-1)|int}

[gcode_macro _LED_MOTORS_OFF]
gcode = 
	_LED_STANDBY
	_LED_VAOC_OFF

[gcode_macro _LED_INPUT_SHAPER_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_INPUT_SHAPER_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_START]
gcode = 
	_LED_ACTION

[gcode_macro _LED_BEACON_CALIBRATION_END]
gcode = 
	_LED_ON

[gcode_macro _LED_BEACON_CALIBRATION_ERROR]
gcode = 
	_LED_ERROR

[gcode_macro _LED_VAOC_ON]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=1.0 GREEN=1.0 BLUE=1.0
	{% endif %}

[gcode_macro _LED_VAOC_OFF]
gcode = 
	{% if printer['neopixel vaoc_led'] is defined %}
	SET_LED LED=vaoc_led RED=0.0 GREEN=0.0 BLUE=0.0
	{% endif %}

[gcode_macro _LED_ACTION]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_action %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SUCCESS]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_success %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_HEATING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_heating %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_COOLING]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_cooling %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ERROR]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_error %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_ON]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_on %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_OFF]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_off %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_STANDBY]
gcode = 
	{% set rgb = printer["gcode_macro RatOS"].led_status_standby %}
	_LED_SET TOOLHEAD={params.TOOLHEAD|default(-1)|int} R={rgb[0]} G={rgb[1]} B={rgb[2]}

[gcode_macro _LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}
	
	{% if toolhead >= 0 %}
	{% if printer['neopixel nozzle_led_t%s' % toolhead] is defined  %}
	SET_LED LED={'nozzle_led_t%s' % toolhead} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% else %}
	{% if printer['neopixel nozzle_led_t0'] is defined  %}
	SET_LED LED={'nozzle_led_t0'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% if printer['neopixel nozzle_led_t1'] is defined %}
	SET_LED LED={'nozzle_led_t1'} RED={r} GREEN={g} BLUE={b} SYNC=0
	{% endif %}
	{% endif %}
	
	_USER_LED_SET { rawparams }

[gcode_macro _USER_LED_SET]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set r = params.R|default(0)|float %}
	{% set g = params.G|default(0)|float %}
	{% set b = params.B|default(0)|float %}

[gcode_macro LOAD_FILAMENT]
description = Loads new filament. Note: be careful with PETG, make sure you inspect the tip of your filament before loading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% if filament_name == '' or filament_type == '' %}
	{% set filament_name = 'unknown' %}
	{% set filament_type = 'unknown' %}
	{% endif %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_LOAD_FILAMENT TEMP={temp} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_LOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME={filament_name} TYPE={filament_type} AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_LOAD_FILAMENT]
description = Load filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_LOAD_FILAMENT" MSG="TEMP={temp}"
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=load_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	_LOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	
	
	RESTORE_GCODE_STATE NAME=load_state
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament load routine complete, please check that the filament was loaded correctly."

[gcode_macro _IDEX_LOAD_FILAMENT]
description = Load filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Loading filament into T{toolhead}..."
	
	DEBUG_ECHO PREFIX="_IDEX_LOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_LOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	_LOAD_FILAMENT TOOLHEAD={toolhead} TEMP={temp} AUTOMATED={automated}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	{% if filament_name != '' and filament_type != '' %}
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('{filament_type}', '{filament_name}', {temp})"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='"{filament_name}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='"{filament_type}"'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE={temp}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_ok}"'
	
	
	_LED_FILAMENT_LOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="Filament load routine for T{toolhead} complete, please check that the filament was loaded correctly."

[gcode_macro _LOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default(false)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE TOOLHEAD={toolhead}
	_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_EXTRUDER_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into hotend.."
	G92 E0
	G0 E{extruder_gear_to_cooling_position_distance} F{extruder_load_speed}
	G92 E0
	M400
	RATOS_ECHO MSG="Filament loaded into hotend."

[gcode_macro _LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set load_speed = printer["gcode_macro T%s" % toolhead].filament_load_speed|float * 60 %}
	{% set filament_loading_nozzle_offset = printer["gcode_macro T%s" % toolhead].filament_loading_nozzle_offset|float %}
	{% set cooling_position_to_nozzle_distance = printer["gcode_macro T%s" % toolhead].cooling_position_to_nozzle_distance|float %}
	{% set purge_after_load = printer["gcode_macro T%s" % toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_LOAD_FILAMENT_FROM_COOLING_ZONE_TO_NOZZLE" MSG="TOOLHEAD: {toolhead}"
	
	
	RATOS_ECHO MSG="Loading filament into nozzle... Please wait!"
	G92 E0
	
	G0 E{cooling_position_to_nozzle_distance + filament_loading_nozzle_offset} F{load_speed}
	G92 E0
	G4 P1000
	_PURGE_FILAMENT	TOOLHEAD={toolhead} E={purge_after_load}
	RATOS_ECHO MSG="Filament loaded into nozzle!"

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"
	
	
	{% set filament_grabbing_length = printer["gcode_macro T%s" % toolhead].filament_grabbing_length|float %}
	{% set filament_grabbing_speed = printer["gcode_macro T%s" % toolhead].filament_grabbing_speed|float %}
	{% set resume_after_insert = true if printer["gcode_macro T%s" % toolhead].resume_after_insert|default(true)|lower == 'true' else false %}
	{% set enable_insert_detection = true if printer["gcode_macro T%s" % toolhead].enable_insert_detection|default(true)|lower == 'true' else false %}
	
	
	{% set current_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	
	{% if enable_insert_detection %}
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_INSERT" MSG="toolhead: {toolhead}, filament_grabbing_length: {filament_grabbing_length}, filament_grabbing_speed: {filament_grabbing_speed}, current_idex_mode: {current_idex_mode}"
	
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Loading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	RATOS_ECHO MSG="Filament inserted into T{toolhead}, loading..."
	
	
	FORCE_MOVE STEPPER={'extruder%s' % ('' if toolhead == 0 else toolhead)} DISTANCE={filament_grabbing_length} VELOCITY={filament_grabbing_speed}
	M400
	
	
	{% if printer.pause_resume.is_paused %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% if resume_after_insert %}
	RESUME
	{% endif %}
	{% else %}
	{% if not printer.virtual_sdcard.is_active %}
	LOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_INSERT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_INSERT" MSG="TOOLHEAD: {toolhead}"

[gcode_macro _PURGE_BEFORE_UNLOAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set purge_before_unload = printer["gcode_macro T%s" % toolhead].purge_before_unload|float %}
	
	DEBUG_ECHO PREFIX="_PURGE_BEFORE_UNLOAD" MSG="TOOLHEAD: {toolhead}"
	
	
	{% if purge_before_unload > 0 %}
	G92 E0
	G0 E{purge_before_unload} F300
	G92 E0
	M400
	{% endif %}

[gcode_macro _PURGE_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set e = params.E|int %}
	{% set r = params.R|default(0)|int %}
	
	DEBUG_ECHO PREFIX="_PURGE_FILAMENT" MSG="TOOLHEAD: {toolhead}, E: {e}"
	
	
	{% if e > 0 %}
	
	
	G92 E0
	G0 E{e} F300
	G92 E0
	M400
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={0.4 if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={0.4 if toolhead == 1 else 0}
	{% else %}
	M106 S{(255 * 0.4)}
	{% endif %}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if r > 0 %}
	G92 E0
	G0 E-{r} F300
	G92 E0
	M400
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["dual_carriage"] is defined %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% else %}
	M106 S0
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro _MOVE_TO_LOADING_POSITION]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_MOVE_TO_LOADING_POSITION" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	
	G1 X{loading_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _CLEANING_MOVE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_CLEANING_MOVE" MSG="TOOLHEAD: {toolhead}"
	
	{% if automated %}
	{% if printer["dual_carriage"] is defined or printer["rmmu_hub"] is defined %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if printer["gcode_macro T%s" % toolhead].has_oozeguard|default(false)|lower == 'true' %}
	{% if printer["gcode_macro T%s" % toolhead].parking_position is defined and printer["gcode_macro T%s" % toolhead].loading_position is defined %}
	
	
	{% set loading_position = printer["gcode_macro T%s" % toolhead].loading_position|float %}
	{% set parking_position = printer["gcode_macro T%s" % toolhead].parking_position|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	
	{% set cleaning_position = loading_position %}
	{% if loading_position == parking_position %}
	{% if loading_position > 0 %}
	{% set cleaning_position = loading_position - 30 %}
	{% else %}
	{% set cleaning_position = loading_position + 30 %}
	{% endif %}
	{% endif %}
	
	
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	G1 X{cleaning_position} F{speed}
	G1 X{parking_position} F{speed}
	
	
	M400
	
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _BED_MESH_SANITY_CHECK]
gcode = 
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is defined %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_start_print_true_zero_fuzzy_position %}
	CONSOLE_ECHO TYPE="error" TITLE="Defined zero reference not compatible with fuzzy true zero" MSG="Using fuzzy start print true zero position is not compatible with a defined zero_reference_position value in the [bed_mesh] section in printer.cfg._N_Please remove the zero_reference_position value from the [bed_mesh] section, or disable fuzzy true zero position in printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_start_print_true_zero_fuzzy_position: False"
	_STOP_AND_RAISE_ERROR MSG="Defined zero reference not compatible with fuzzy true zero"
	{% elif zero_ref_pos[0]|float|round != safe_home_x|float|round or zero_ref_pos[1]|float|round != safe_home_y|float|round %}
	CONSOLE_ECHO TYPE="error" TITLE="Zero reference position does not match safe home position" MSG="Please update your bed mesh zero reference position in printer.cfg, like so:_N__N_[bed_mesh]_N_zero_reference_position: {safe_home_x|float|round},{safe_home_y|float|round}_N_"
	_STOP_AND_RAISE_ERROR MSG="Zero reference position does not match safe home position"
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_bed_mesh %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact bed mesh is enabled" MSG="Beacon contact bed mesh is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_bed_mesh: False"
	{% endif %}
	
	{% if beacon_scan_method_automatic %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon 'automatic' scan method is enabled" MSG="Beacon 'automatic' scan method is enabled. This is not recommended for normal use and may result in inaccurate bed mesh calibration._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_scan_method_automatic: False"
	{% endif %}
	
	{% if beacon_contact_z_tilt_adjust %}
	CONSOLE_ECHO TYPE="warning" TITLE="Beacon contact z-tilt adjust is enabled" MSG="Beacon contact z-tilt adjust is enabled. This is not recommended for normal use and may result in inaccurate z-tilt adjustment._N_Please disable it in your printer.cfg, like so:_N__N_[gcode_macro RatOS]_N_variable_beacon_contact_z_tilt_adjust: False"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH]
gcode = 
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE=None
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE=None
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION {rawparams}
	{% endif %}

[gcode_macro _START_PRINT_BED_MESH]
variable_actual_true_zero_position_x = None
variable_actual_true_zero_position_y = None
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set X=[params.X0|default(-1)|float, params.X1|default(-1)|float] %}
	{% set Y=[params.Y0|default(-1)|float, params.Y1|default(-1)|float] %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_BED_MESH" MSG="idex_mode: {idex_mode}, X: {X}, Y: {Y}"
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set zero_ref_pos = printer.fastconfig.settings.bed_mesh.zero_reference_position %}
	{% if zero_ref_pos is not defined %}
	{% set zero_ref_pos = [safe_home_x if actual_true_zero_position_x is none else actual_true_zero_position_x, safe_home_y if actual_true_zero_position_y is none else actual_true_zero_position_y] %}
	{% endif %}
	
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	
	
	
	
	{% set X=[0, printable_x_max] %}
	{% endif %}
	
	
	{% set beacon_bed_mesh_scv = printer["gcode_macro RatOS"].beacon_bed_mesh_scv|default(25)|int %}
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	{% if printer.fastconfig.settings.beacon is defined and not beacon_contact_bed_mesh %}
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={beacon_bed_mesh_scv}
	{% endif %}
	
	
	{% set default_profile = printer["gcode_macro RatOS"].bed_mesh_profile|default('ratos') %}
	{% if printer["gcode_macro RatOS"].calibrate_bed_mesh|lower == 'true' %}
	BED_MESH_CLEAR
	{% if printer["gcode_macro RatOS"].adaptive_mesh|lower == 'true' %}
	CALIBRATE_ADAPTIVE_MESH PROFILE="{default_profile}" X0={X[0]} X1={X[1]} Y0={Y[0]} Y1={Y[1]} T={params.T|int} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={idex_mode} ZERO_REF_POS_X={zero_ref_pos[0]} ZERO_REF_POS_Y={zero_ref_pos[1]}
	{% else %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% endif %}
	BED_MESH_PROFILE LOAD="{default_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	
	{% elif printer["gcode_macro RatOS"].bed_mesh_profile is defined %}
	BED_MESH_CLEAR
	BED_MESH_PROFILE LOAD="{printer["gcode_macro RatOS"].bed_mesh_profile}"
	
	SET_ZERO_REFERENCE_POSITION X={zero_ref_pos[0]} Y={zero_ref_pos[1]}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_bed_mesh"

[gcode_macro CALIBRATE_ADAPTIVE_MESH]
gcode = 
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_bed_mesh_samples = printer["gcode_macro RatOS"].beacon_contact_bed_mesh_samples|default(2)|int %}
	{% set beacon_contact_bed_mesh = true if printer["gcode_macro RatOS"].beacon_contact_bed_mesh|default(false)|lower == 'true' else false %}
	{% set beacon_scan_method_automatic = true if printer["gcode_macro RatOS"].beacon_scan_method_automatic|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set default_profile = params.PROFILE %}
	
	
	{% set x0 = params.X0|default(-1)|float %}
	{% set y0 = params.Y0|default(-1)|float %}
	{% set x1 = params.X1|default(-1)|float %}
	{% set y1 = params.Y1|default(-1)|float %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Received coordinates X0={x0|round(1)} Y0={y0|round(1)} X1={x1|round(1)} Y1={y1|round(1)}"
	
	{% if x0 >= x1 or y0 >= y1 %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Invalid coordinates received. Please check your slicer settings. Falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	
	
	{% if params.ZERO_REF_POS_X is defined and params.ZERO_REF_POS_Y is defined %}
	{% set zero_ref_pos_x = params.ZERO_REF_POS_X|float %}
	{% set zero_ref_pos_y = params.ZERO_REF_POS_Y|float %}
	{% if zero_ref_pos_x < x0 or zero_ref_pos_x > x1 or zero_ref_pos_y < y0 or zero_ref_pos_y > y1 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Zero reference position X={zero_ref_pos_x|round(1)} Y={zero_ref_pos_y|round(1)} is outside the mesh region, expanding mesh region to include it."
	{% set x0 = [x0, zero_ref_pos_x]|min %}
	{% set y0 = [y0, zero_ref_pos_y]|min %}
	{% set x1 = [x1, zero_ref_pos_x]|max %}
	{% set y1 = [y1, zero_ref_pos_y]|max %}
	{% endif %}
	{% endif %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float %}
	
	
	{% set mesh_x0 = [[x0, max_x]|min, min_x]|max %}
	{% set mesh_y0 = [[y0, max_y]|min, min_y]|max %}
	{% set mesh_x1 = [[x1, max_x]|min, min_x]|max %}
	{% set mesh_y1 = [[y1, max_y]|min, min_y]|max %}
	
	{% if mesh_x0 == min_x and mesh_y0 == min_y and mesh_x1 == max_x and mesh_y1 == max_y %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Print is using the full bed, falling back to full bed mesh."
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}"
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}"
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% endif %}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}"
	{% endif %}
	{% else %}
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	
	{% set probe_count_x = mesh_config.probe_count.split(",")[0]|int %}
	{% if mesh_config.probe_count.split(",")|length == 2 %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[1]|int %}
	{% else %}
	{% set probe_count_y = mesh_config.probe_count.split(",")[0]|int %}
	{% endif %}
	
	
	{% set probe_x_step = (max_x - min_x) / probe_count_x %}
	{% set probe_y_step = (max_y - min_y) / probe_count_y %}
	
	
	{% set mesh_count_x = ([(mesh_x1 - mesh_x0) / probe_x_step, 3]|max)|int %}
	{% set mesh_count_y = ([(mesh_y1 - mesh_y0) / probe_y_step, 3]|max)|int %}
	{% set min_mesh_count = [mesh_count_x, mesh_count_y]|min %}
	{% set max_mesh_count = [mesh_count_x, mesh_count_y]|max %}
	
	
	{% set algorithm = mesh_config.algorithm %}
	{% if algorithm|lower == 'lagrange' and max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="cannot exceed a probe_count of 6 when using lagrange interpolation. Falling back to bicubic interpolation."
	{% set algorithm = 'bicubic' %}
	{% endif %}
	{% if algorithm|lower == 'bicubic' and min_mesh_count < 4 %}
	{% if max_mesh_count > 6 %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="invalid probe_count option when using bicubic interpolation. Combination of 3 points on one axis with more than 6 on another is not permitted. Forcing minimum mesh count to be 4."
	{% set min_mesh_count = 4 %}
	{% else %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="bicubic interpolation with a probe_count of less than 4 points detected. Forcing lagrange interpolation."
	{% set algorithm = 'lagrange' %}
	{% endif %}
	{% endif %}
	
	{% set mesh_count_x = ([min_mesh_count, mesh_count_x]|max)|int %}
	{% set mesh_count_x = ([max_mesh_count, mesh_count_x]|min)|int %}
	{% set mesh_count_y = ([min_mesh_count, mesh_count_y]|max)|int %}
	{% set mesh_count_y = ([max_mesh_count, mesh_count_y]|min)|int %}
	
	{% set should_prime = printer["gcode_macro RatOS"].nozzle_priming == 'primeblob' %}
	{% if printer["dual_carriage"] is not defined %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% else %}
	
	{% set probe_first = printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == "min" or printer["gcode_macro RatOS"].nozzle_prime_start_y|float(printable_y_max) < printable_y_max / 2 %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 != 0 and probe_first %}
	{% set probe_first = false %}
	{% elif printer.fastconfig.settings.beacon is defined and printer.fastconfig.settings.beacon.mesh_runs % 2 == 0 and not probe_first %}
	{% set probe_first = true %}
	{% endif %}
	
	
	{% if should_prime and probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="mesh coordinates X0={mesh_x0|round(1)} Y0={mesh_y0|round(1)} X1={mesh_x1|round(1)} Y1={mesh_y1|round(1)}"
	{% if printer.fastconfig.settings.beacon is defined %}
	{% if beacon_contact_bed_mesh %}
	BED_MESH_CALIBRATE PROBE_METHOD=contact USE_CONTACT_AREA=1 SAMPLES={beacon_contact_bed_mesh_samples} PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y} RELATIVE_REFERENCE_INDEX=-1
	{% else %}
	{% if beacon_scan_method_automatic %}
	BED_MESH_CALIBRATE METHOD=automatic PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	{% endif %}
	_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED
	{% else %}
	BED_MESH_CALIBRATE PROFILE="{default_profile}" ALGORITHM={algorithm} MESH_MIN={mesh_x0},{mesh_y0} MESH_MAX={mesh_x1},{mesh_y1} PROBE_COUNT={mesh_count_x},{mesh_count_y}
	{% endif %}
	
	
	{% if should_prime and not probe_first %}
	{% if printer["dual_carriage"] is not defined %}
	
	PROBE_FOR_PRIMING
	{% else %}
	
	{% if both_toolheads %}
	PROBE_FOR_PRIMING TOOLHEAD=0 IDEX_MODE={idex_mode}
	PROBE_FOR_PRIMING TOOLHEAD=1 IDEX_MODE={idex_mode}
	{% else %}
	PROBE_FOR_PRIMING TOOLHEAD={params.T|int} IDEX_MODE={idex_mode}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	{% endif %}
	{% endif %}

[gcode_macro M84]
rename_existing = M84.1
gcode = 
	
	M84.1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_OFFSET X=0 Y=0
	
	
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro _VAOC"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False
	{% endif %}
	
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	SET_SKEW CLEAR=1
	
	
	_LED_MOTORS_OFF

[gcode_macro M104]
rename_existing = M104.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M104" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set temperature_offset_t0 = printer["gcode_macro T0"].temperature_offset|default(0)|int %}
	{% set temperature_offset_t1 = printer["gcode_macro T1"].temperature_offset|default(0)|int %}
	{% set s0 = [s + temperature_offset_t0, 0]|max %}
	{% set s1 = [s + temperature_offset_t1, 0]|max %}
	{% if temperature_offset_t0 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t0}°C added to toolhead T0."
	{% endif %}
	{% if temperature_offset_t1 != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset_t1}°C added to toolhead T1."
	{% endif %}
	{% else %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M104" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	M104.1 S{s0} T0
	M104.1 S{s1} T1
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% else %}
	M104.1 S{s} T{t}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M109]
rename_existing = M109.1
gcode = 
	
	{% set s = params.S|default(0)|int %}
	{% set t = params.T|default(-1)|int %}
	{% set t = 0 if t == -1 else t %}
	
	
	{% if printer["rmmu_hub"] is defined %}
	{% set t = printer["rmmu_hub"].logical_mapping["%s" % t]["PHYSICAL_TOOLHEAD"]|int %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="M109" MSG="s: {s}, t: {t}"
	
	
	{% if printer["gcode_macro T%s" % t] is defined %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set s = [s + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="M109" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	
	{% set is_in_standby = false %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% if toolchange_standby_temp > -1 %}
	{% set is_in_standby = true if printer["gcode_macro T%s" % t].standby|default(false)|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	
	
	{% if not is_in_standby %}
	M109.1 S{s} T{t}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro SET_HEATER_TEMPERATURE]
rename_existing = SET_HEATER_TEMPERATURE_BASE
gcode = 
	
	{% set heater = params.HEATER|default("") %}
	{% set target = params.TARGET|default(0)|int %}
	
	DEBUG_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="heater: {heater}, target: {target}"
	
	{% set t = -1 %}
	{% if heater|lower == "extruder" or heater|lower == "extruder1" %}
	
	{% set t = 0 if heater|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and target > 0 %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% set target = [target + temperature_offset, 0]|max %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="SET_HEATER_TEMPERATURE" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE_BASE HEATER="{heater}" TARGET={target}
	
	{% if t != -1 and printer.fastconfig.settings.beacon is defined %}
	
	{% set is_printing_gcode = printer["gcode_macro START_PRINT"].is_printing_gcode|default(false)|lower == 'true' %}
	{% if is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	{% endif %}

[gcode_macro TEMPERATURE_WAIT]
rename_existing = TEMPERATURE_WAIT_BASE
gcode = 
	
	{% set sensor = params.SENSOR|default("") %}
	{% set minimum = params.MINIMUM|default(-1)|int %}
	{% set maximum = params.MAXIMUM|default(-1)|int %}
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="sensor: {sensor}, minimum: {minimum}, maximum: {maximum}"
	
	{% set t = -1 %}
	{% if sensor|lower == "extruder" or sensor|lower == "extruder1" %}
	
	{% set t = 0 if sensor|lower == "extruder" else 1 %}
	
	
	{% if printer["gcode_macro T%s" % t] is defined and (minimum > 0 or maximum > 0) %}
	{% set temperature_offset = printer["gcode_macro T%s" % t].temperature_offset|default(0)|int %}
	{% if minimum > -1 %}
	{% set minimum = [minimum + temperature_offset, 0]|max %}
	{% endif %}
	{% if maximum > -1 %}
	{% set maximum = [maximum + temperature_offset, 0]|max %}
	{% endif %}
	{% if temperature_offset != 0 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature offset of {temperature_offset}°C added to toolhead T{t}."
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set id = "sensor " ~ sensor if t == -1 else "toolhead T" ~ t %}
	
	
	{% if minimum > -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum} MAXIMUM={maximum}
	{% elif minimum > -1 and maximum == -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MINIMUM: {minimum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MINIMUM={minimum}
	{% elif minimum == -1 and maximum > -1 %}
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}, MAXIMUM: {maximum}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}" MAXIMUM={maximum}
	{% else %}
	
	
	DEBUG_ECHO PREFIX="TEMPERATURE_WAIT" MSG="neither MINIMUM or MAXIMUM args were specified, call TEMPERATURE_WAIT_BASE is expected to fail"
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Waiting for {id}"
	RATOS_ECHO MSG="please wait..."
	TEMPERATURE_WAIT_BASE SENSOR="{sensor}"
	{% endif %}
	
	RATOS_ECHO PREFIX="TEMPERATURE_WAIT" MSG="Temperature for {id} reached."

[gcode_macro SDCARD_PRINT_FILE]
rename_existing = SDCARD_PRINT_FILE_BASE
gcode = 
	{% if printer["ratos"] is defined %}
	PROCESS_GCODE_FILE { rawparams }
	{% else %}
	SDCARD_PRINT_FILE_BASE { rawparams }
	{% endif %}

[gcode_macro SKEW_PROFILE]
rename_existing = SKEW_PROFILE_BASE
variable_loaded_profile = ""
gcode = 
	{% if params.LOAD is defined %}
	{% if printer.fastconfig.settings["skew_correction %s" % params.LOAD] is defined %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='"{params.LOAD}"'
	{% endif %}
	{% endif %}
	
	SKEW_PROFILE_BASE { rawparams }

[gcode_macro SET_SKEW]
rename_existing = SET_SKEW_BASE
gcode = 
	{% if params.CLEAR is defined %}
	{% if params.CLEAR|default(0)|int == 1 %}
	SET_GCODE_VARIABLE MACRO=SKEW_PROFILE VARIABLE=loaded_profile VALUE='""'
	{% endif %}
	{% endif %}
	
	SET_SKEW_BASE { rawparams }

[gcode_macro SET_VELOCITY_LIMIT]
rename_existing = SET_VELOCITY_LIMIT_BASE
gcode = 
	{% if params.ACCEL_TO_DECEL is defined %}
	
	{% if params.ACCEL is defined %}
	{% set accel = params.ACCEL|float %}
	{% else %}
	{% set accel = printer.toolhead.max_accel|float %}
	{% endif %}
	
	{% if params.VELOCITY is defined %}
	{% set velocity = params.VELOCITY|float %}
	{% else %}
	{% set velocity = printer.toolhead.max_velocity|float %}
	{% endif %}
	
	{% if params.SQUARE_CORNER_VELOCITY is defined %}
	{% set scv = params.SQUARE_CORNER_VELOCITY|float %}
	{% else %}
	{% set scv = printer.toolhead.square_corner_velocity|float %}
	{% endif %}
	
	{% set mcr = params.ACCEL_TO_DECEL|float / accel %}
	
	DEBUG_ECHO PREFIX="SET_VELOCITY_LIMIT" MSG="ACCEL={accel}, VELOCITY={velocity}, SQUARE_CORNER_VELOCITY={scv}, MINIMUM_CRUISE_RATIO={mcr}"
	
	SET_VELOCITY_LIMIT_BASE ACCEL={accel} VELOCITY={velocity} SQUARE_CORNER_VELOCITY={scv} MINIMUM_CRUISE_RATIO={1-mcr}
	
	{% else %}
	
	SET_VELOCITY_LIMIT_BASE { rawparams }
	
	{% endif %}

[gcode_macro BED_MESH_CALIBRATE]
rename_existing = _BED_MESH_CALIBRATE_BASE
variable_abl_and_home_z_if_required = True
gcode = 
	{% set z_probe = printer["gcode_macro RatOS"].z_probe %}
	{% if abl_and_home_z_if_required %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	G28 Z
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	G28 Z
	{% endif %}
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set beacon_default_probe_method = printer.fastconfig.settings.beacon.default_probe_method|default('proximity') %}
	{% set probe_method = params.PROBE_METHOD|default(beacon_default_probe_method)|lower %}
	{% if probe_method == 'proximity' %}
	_CHECK_ACTIVE_BEACON_MODEL_TEMP TITLE="Bed mesh calibration warning"
	{% endif %}
	{% endif %}
	{% if z_probe == "stowable" %}
	DEPLOY_PROBE
	{% endif %}
	_BED_MESH_CALIBRATE_BASE {rawparams}
	{% if z_probe == "stowable" %}
	STOW_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	_APPLY_RATOS_BED_MESH_PARAMETERS {rawparams}
	{% endif %}

[gcode_macro SET_GCODE_OFFSET]
rename_existing = SET_GCODE_OFFSET_BASE
gcode = 
	DEBUG_ECHO PREFIX="SET_GCODE_OFFSET" MSG="{rawparams|replace('"', '')|replace("'", '')}"
	{% set z_before = printer.gcode_move.homing_origin.z|float %}
	SET_GCODE_OFFSET_BASE {rawparams}
	_AFTER_SET_GCODE_OFFSET Z_BEFORE={z_before}

[gcode_macro _AFTER_SET_GCODE_OFFSET]
gcode = 
	{% set z_before = params.Z_BEFORE|float %}
	{% set z_after = printer.gcode_move.homing_origin.z|float %}
	{% if z_before != z_after %}
	_ALERT_NON_ZERO_Z_OFFSET FORCE=1
	{% endif %}

[gcode_macro _START_PRINT_PARK]
gcode = 
	
	{% set z = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_x = printer["gcode_macro RatOS"].start_print_park_x %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% if printer["gcode_macro RatOS"].start_print_park_x is defined and printer["gcode_macro RatOS"].start_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="start_print_park_x is ignored for IDEX printers"
	{% endif %}
	PARK_TOOLHEAD
	G90
	{% endif %}
	
	
	_PARK LOCATION={start_print_park_in} X={start_print_park_x}
	G0 Z{z} F{z_speed}

[gcode_macro _END_PRINT_PARK]
gcode = 
	{% if printer["dual_carriage"] is defined %}
	
	{% if printer["gcode_macro RatOS"].end_print_park_x is defined and printer["gcode_macro RatOS"].end_print_park_x != '' %}
	RATOS_ECHO PREFIX="WARNING" MSG="end_print_park_x is ignored for IDEX printers"
	{% endif %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	PARK_TOOLHEAD
	G90
	{% endif %}
	_PARK LOCATION={printer["gcode_macro RatOS"].end_print_park_in} X={printer["gcode_macro RatOS"].end_print_park_x}

[gcode_macro _PARK]
gcode = 
	
	{% set x = params.X %}
	{% set location = params.LOCATION|default('back')|lower %}
	
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	{% set nozzle_priming = printer["gcode_macro RatOS"].nozzle_priming|lower %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="park"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% if x != '' %}
	{% if x|float >= printer.toolhead.axis_minimum.x + 5 and x|float <= printable_x_max - 5 %}
	{% set park_x = x|float %}
	{% else %}
	{action_respond_info('The requested X co-ordinate is outside the defined axis bounds - using defaults')}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	{% else %}
	{% set park_x = printable_x_max / 2 %}
	{% endif %}
	
	
	{% set park_y = printable_y_max - 15 %}
	{% if location == 'front' %}
	{% set park_y = printer.toolhead.axis_minimum.y + 5 %}
	{% elif location == 'center' %}
	{% set park_y = printable_y_max / 2 %}
	{% elif location == 'primeblob' and printer["dual_carriage"] is defined %}
	
	{% set park_y = printable_y_max - 15 %}
	{% endif %}
	
	
	{% if location == 'primeblob' and printer["dual_carriage"] is not defined %}
	{% if (nozzle_priming == 'primeblob' or nozzle_priming == 'primeline') %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set park_x = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set park_x = printable_x_max - 5 %}
	{% else %}
	{% set park_x = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set park_y = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set park_y = printable_y_max - 5 %}
	{% else %}
	{% set park_y = nozzle_prime_start_y|float %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	G0 X{park_x} Y{park_y} F{speed}
	{% else %}
	
	G0 Y{park_y} F{speed}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="park"

[gcode_macro SAVE_PROBE_RESULT]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	{% set last_z_offset = 9999.9 %}
	{% if printer.fastconfig.settings.beacon is defined %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if beacon_contact_prime_probing %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	{% else %}
	{% set last_z_offset = printer.beacon.last_sample.dist - current_z %}
	{% endif %}
	{% elif printer.fastconfig.settings.bltouch is defined  %}
	{% set config_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% elif printer.fastconfig.settings.probe is defined  %}
	{% set config_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% set last_z_offset = printer.probe.last_z_result - config_offset %}
	{% endif %}
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Saving offset adjustment of {last_z_offset} in {params.VARIABLE|default('last_z_offset')}"
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE={params.VARIABLE|default('last_z_offset')} VALUE={last_z_offset}

[gcode_macro PROBE_FOR_PRIMING]
gcode = 
	
	{% set probe_for_priming_disable_mesh_constraints = true if printer["gcode_macro RatOS"].probe_for_priming_disable_mesh_constraints|default(false)|lower == 'true' else false %}
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower != 'false' %}
	SAVE_GCODE_STATE NAME=probe_for_priming_state
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the prime location.."
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set t = params.TOOLHEAD|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% if idex_mode == '' %}
	
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% if t == 0 %}
	{% set x_start = 5 %}
	{% else %}
	{% set x_start = printable_x_max - 5 %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% endif %}
	{% endif %}
	{% set z = printer.fastconfig.settings.bed_mesh.horizontal_move_z|float %}
	
	
	{% set mesh_config = printer.fastconfig.config.bed_mesh %}
	
	
	{% if printer.fastconfig.settings.bltouch is defined %}
	{% set x_offset = printer.fastconfig.settings.bltouch.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.bltouch.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.bltouch.z_offset|float %}
	{% elif printer.fastconfig.settings.probe is defined %}
	{% set x_offset = printer.fastconfig.settings.probe.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.probe.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.probe.z_offset|float %}
	{% elif printer.fastconfig.settings.beacon is defined %}
	{% set x_offset = printer.fastconfig.settings.beacon.x_offset|float %}
	{% set y_offset = printer.fastconfig.settings.beacon.y_offset|float %}
	{% set z_offset = printer.fastconfig.settings.beacon.trigger_distance|float %}
	{% else %}
	{ action_raise_error("No probe, beacon or bltouch section found. Adaptive priming only works with a [probe], [beacon] or [bltouch] section defined.") }
	{% endif %}
	
	{% if z < z_offset %}
	{ action_raise_error("Horizontal move Z ({z}) is below your probe's Z offset ({z_offset}). Please adjust your horizontal_move_z setting in [bed_mesh] to be above {z}.") }
	{% endif %}
	
	{% if not probe_for_priming_disable_mesh_constraints %}
	
	{% set min_x = mesh_config.mesh_min.split(",")[0]|float - x_offset %}
	{% set min_y = mesh_config.mesh_min.split(",")[1]|float - y_offset %}
	{% set max_x = mesh_config.mesh_max.split(",")[0]|float - x_offset %}
	{% set max_y = mesh_config.mesh_max.split(",")[1]|float - y_offset %}
	
	
	{% set x_start = [[x_start, max_x]|min, min_x]|max %}
	{% set y_start = [[y_start, max_y]|min, min_y]|max %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the start of the prime location at {x_start}, {y_start}"
	
	G90
	
	M83
	
	G0 Z{z} F{z_speed}
	
	G1 X{x_start} Y{y_start} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_result
	{% endif %}
	
	{% if idex_mode == '' %}
	
	{% set x_end = x_start %}
	{% set y_end = y_start + 45 %}
	{% else %}
	
	{% if t==1 %}
	{% set x_end = x_start - 45 %}
	{% else %}
	{% set x_end = x_start + 45 %}
	{% endif %}
	{% set y_end = y_start %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Adaptive Mesh" MSG="Probing the end of the prime location at {x_end}, {y_end}"
	G1 X{x_end} Y{y_end} F{speed}
	PROBE_CURRENT_POSITION
	{% if t == 1 %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result_t1
	{% else %}
	SAVE_PROBE_RESULT VARIABLE=probe_for_priming_end_result
	{% endif %}
	
	RESTORE_GCODE_STATE NAME=probe_for_priming_state
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="probe_for_priming"
	{% endif %}

[gcode_macro RESET_PRIME_PROBE_STATE]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result VALUE=None
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_result_t1 VALUE=None
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=probe_for_priming_end_result_t1 VALUE=None
	{% endif %}

[gcode_macro PROBE_CURRENT_POSITION]
gcode = 
	
	{% set beacon_contact_prime_probing = true if printer["gcode_macro RatOS"].beacon_contact_prime_probing|default(false)|lower == 'true' else false %}
	
	SAVE_GCODE_STATE NAME=probe_current_position_state
	{% if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	ASSERT_PROBE_DEPLOYED
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_prime_probing %}
	PROBE PROBE_METHOD=contact SAMPLES=1
	{% else %}
	PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined %}
	BEACON_QUERY
	{% else %}
	
	RESTORE_GCODE_STATE NAME=probe_current_position_state MOVE=1 MOVE_SPEED={printer["gcode_macro RatOS"].macro_z_speed|float}
	{% endif %}

[gcode_macro PRIME_BLOB]
description = Prints a primeblob, used internally, if configured, as part of the START_PRINT macro.
variable_x_offset = 5
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="prime_blob"
	SET_MACRO_TRAVEL_SETTINGS
	
	RATOS_ECHO PREFIX="Priming" MSG="Priming nozzle with prime blob.."
	
	
	{% set current_toolhead = 0 %}
	
	
	{% set target_idex_mode = '' %}
	{% set extruder = 'extruder' %}
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE is defined %}
	{% set target_idex_mode = params.IDEX_MODE|default('')|lower %}
	{% else %}
	{ action_raise_error("IDEX_MODE parameter not found for PRIME_BLOB macro. This is likely a bug.") }
	{% endif %}
	RATOS_ECHO PREFIX="Priming" MSG="Priming in IDEX {target_idex_mode} mode.."
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set current_toolhead = 1 if current_idex_mode=='primary' else 0 %}
	{% set extruder = 'extruder1' if current_toolhead == 1 else 'extruder' %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	SAVE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set fan_speed = printer["gcode_macro RatOS"].nozzle_prime_bridge_fan|float %}
	{% set nozzle_diameter = printer.fastconfig.settings[extruder].nozzle_diameter|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set has_start_offset_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) != 9999.9 %}
	{% if printer["dual_carriage"] is defined %}
	{% set has_start_offset_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) != 9999.9 %}
	{% endif %}
	{% set start_print_park_in = printer["gcode_macro RatOS"].start_print_park_in %}
	{% set start_print_park_z_height = printer["gcode_macro RatOS"].start_print_park_z_height|float %}
	{% set nozzle_prime_direction = printer["gcode_macro RatOS"].nozzle_prime_direction|lower %}
	{% set nozzle_prime_start_x = printer["gcode_macro RatOS"].nozzle_prime_start_x %}
	{% set nozzle_prime_start_y = printer["gcode_macro RatOS"].nozzle_prime_start_y %}
	
	
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% if target_idex_mode == '' %}
	
	{% set x_factor = 0 %}
	{% if nozzle_prime_start_x|lower == 'min' %}
	{% set x_start = 5 %}
	{% elif nozzle_prime_start_x|lower == 'max' %}
	{% set x_start = printable_x_max - 5 %}
	{% else %}
	{% set x_start = nozzle_prime_start_x|float %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_y_max - 5 %}
	{% set y_factor = -1 %}
	{% else %}
	{% set y_start = nozzle_prime_start_y|float %}
	{% if nozzle_prime_start_y|float < printable_y_max / 2 %}
	{% set y_factor = 1 %}
	{% else %}
	{% set y_factor = -1 %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_direction == 'forwards' %}
	{% set y_factor = 1 %}
	{% elif nozzle_prime_direction == 'backwards' %}
	{% set y_factor = -1 %}
	{% endif %}
	{% if start_print_park_in == 'primeblob' %}
	{% set z = 3 %}
	{% else %}
	{% set z = start_print_park_z_height %}
	{% endif %}
	{% else %}
	
	{% set center_x = printable_x_max / 2 %}
	{% set y_factor = 0 %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set x_start = center_x / 2 + 5 %}
	{% set x_factor = 1 %}
	{% else %}
	
	
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% if current_toolhead == 0 %}
	{% set x_start = 55 %}
	{% set x_factor = -1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 55 %}
	{% set x_factor = 1 %}
	{% endif %}
	{% else %}
	{% if current_toolhead == 0 %}
	{% set x_start = 5 %}
	{% set x_factor = 1 %}
	{% elif current_toolhead == 1 %}
	{% set x_start = printable_x_max - 5 %}
	{% set x_factor = -1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if nozzle_prime_start_y|lower == 'min' %}
	{% set y_start = 5 %}
	{% elif nozzle_prime_start_y|lower == 'max' %}
	{% set y_start = printable_x_max - 5 %}
	{% endif %}
	{% set z = 10 %}
	{% endif %}
	
	{% set start_z_offset = 0 %}
	{% set end_z_offset = 0 %}
	{% if has_start_offset_t0 %}
	{% set start_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_result|float(9999.9) %}
	{% set end_z_probe_result_t0 = printer["gcode_macro RatOS"].probe_for_priming_end_result|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t0 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t0) ) }
	{% endif %}
	{% if end_z_probe_result_t0 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t0) )  }
	{% endif %}
	{% set start_z_offset = start_z_probe_result_t0 %}
	{% set end_z_offset = end_z_probe_result_t0 %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	{% if current_toolhead == 1 or both_toolheads or target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	{% if has_start_offset_t1 %}
	{% set start_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_result_t1|float(9999.9) %}
	{% set end_z_probe_result_t1 = printer["gcode_macro RatOS"].probe_for_priming_end_result_t1|float(9999.9) %}
	{% if printer.fastconfig.settings.bltouch is not defined and printer.fastconfig.settings.probe is not defined and printer.fastconfig.settings.beacon is not defined %}
	{ action_raise_error("No probe or bltouch section found. Adaptive priming only works with [probe], [beacon] or [bltouch].") }
	{% endif %}
	{% if start_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No start probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% if end_z_probe_result_t1 == 9999.9 %}
	{ action_raise_error("No end probe result found for prime area. This is likely a bug.") }
	{% endif %}
	{% set adjustment_threshold = printer["gcode_macro RatOS"].adaptive_prime_offset_threshold|float %}
	{% if start_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (start_z_probe_result_t1) ) }
	{% endif %}
	{% if end_z_probe_result_t1 < adjustment_threshold %}
	{ action_raise_error("Abnormal probe offset detected. Needed offset of %.5f is below the offset threshold of -1mm. Please verify the probe is over the bed when probing for priming. If it isn't, you should adjust you min/max bed_mesh settings so the probe is always over the print area." % (end_z_probe_result_t1) ) }
	{% endif %}
	{% set start_z_offset = [start_z_offset, start_z_probe_result_t1]|max %}
	{% set end_z_offset = [end_z_offset, start_z_probe_result_t1]|max %}
	{% endif %}
	{% endif %}
	{% if target_idex_mode != 'copy' and target_idex_mode != 'mirror' %}
	{% if both_toolheads and initial_toolhead != current_toolhead %}
	{% set original_start_z_offset = start_z_offset %}
	{% set original_end_z_offset = end_z_offset %}
	{% set start_z_offset = original_end_z_offset %}
	{% set end_z_offset = original_start_z_offset %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	DEBUG_ECHO PREFIX="PRIME_BLOB" MSG="x_start: {x_start}, y_start: {y_start}, x_factor: {x_factor}, y_factor: {y_factor}, z: {z}, start_z_offset: {start_z_offset}, end_z_offset: {end_z_offset}"
	
	
	G90
	
	M83
	RATOS_ECHO PREFIX="Priming" MSG="Lifting Z to {z}.."
	
	G0 Z{z} F{z_speed}
	
	
	{% if printer["dual_carriage"] is not defined %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% if start_print_park_in != 'primeblob' %}
	G1 X{x_start} F{speed}
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% endif %}
	{% else %}
	
	G1 Y{y_start + (15 * y_factor)} F{speed}
	{% if target_idex_mode=="copy" or target_idex_mode=="mirror" %}
	RATOS_ECHO PREFIX="Priming" MSG="Mirroring move to {x_start}, {y_start} along the edge of the print area.."
	
	_IDEX_MIRROR PRIMING=1
	{% else %}
	RATOS_ECHO PREFIX="Priming" MSG="Moving to {x_start}, {y_start} along the edge of the print area.."
	{% endif %}
	G1 X{x_start} F{speed}
	{% endif %}
	
	RATOS_ECHO PREFIX="Priming" MSG="Starting prime blob.."
	
	G1 Z{0.5 + start_z_offset} F{z_speed}
	
	G1 Y{y_start} F{speed}
	
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	G1 F300 E{14 / ((0.4 / [nozzle_diameter|float, 0.6]|min) ** 2)}
	
	M106 S{fan_speed}
	
	G1 Z5 F100 E5
	G92 E0
	RATOS_ECHO PREFIX="Priming" MSG="Bridging with {((fan_speed/255) * 100)|int}% fan speed.."
	
	G1 F3000 X{x_start + (15 * x_factor)} Y{y_start + (15 * y_factor)} E{1 / ((0.4 / nozzle_diameter) ** 2)}
	
	
	
	G1 F3000 X{x_start + (20 * x_factor)} Y{y_start + (20 * y_factor)} Z{3.8 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (34 * x_factor)} Y{y_start + (34 * y_factor)} Z{2.6 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (38 * x_factor)} Y{y_start + (38 * y_factor)} Z{1.4 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	G1 F3000 X{x_start + (42 * x_factor)} Y{y_start + (42 * y_factor)} Z{0.2 + end_z_offset} E{0.2 / ((0.4 / nozzle_diameter) ** 2)}
	
	M106 S0
	
	G1 F3000 X{x_start + (46 * x_factor)} Y{y_start + (46 * y_factor)} Z{0.2 + end_z_offset} E0.6
	
	G1 F{speed} X{x_start + (50 * x_factor)} Y{y_start + (50 * y_factor)}
	
	
	{% if target_idex_mode == "copy" or target_idex_mode == "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if target_idex_mode == "copy" %}
	{% if first_y >= 0 %}
	_IDEX_COPY DANCE=0 Y={first_y}
	{% else %}
	_IDEX_COPY DANCE=0 Y={params.Y1}
	{% endif %}
	{% endif %}
	
	
	
	
	
	{% if target_idex_mode != "copy" or target_idex_mode != "mirror" %}
	RESTORE_GCODE_STATE NAME=prime_blob_state
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="prime_blob"
	
	
	G92 E0

[gcode_macro UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
variable_ignore_min_extrude_temp = True
gcode = 
	_LEARN_MORE_FILAMENT
	
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set filament_name = params._NAME|default('')|string %}
	{% set filament_type = params._TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set temp = params.TEMP|default(220)|int %}
	{% if printer["dual_carriage"] is not defined %}
	_DEFAULT_UNLOAD_FILAMENT TEMP={temp} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead==0 or toolhead==1 %}
	_IDEX_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	RATOS_ECHO MSG="Please select toolhead! 0 = left, 1 = right toolhead"
	{% endif %}
	{% endif %}

[gcode_macro _DEFAULT_UNLOAD_FILAMENT]
description = Unload filament macro for non IDEX printers.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading filament..."
	
	DEBUG_ECHO PREFIX="_DEFAULT_UNLOAD_FILAMENT" MSG="TEMP: {temp}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD=0
	
	
	SAVE_GCODE_STATE NAME=unload_state
	
	
	{% if printer.extruder.temperature|int < temp or printer.extruder.can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating extruder to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={temp}
	
	
	G4 P3000
	
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD=0 NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TOOLHEAD=0 AUTOMATED={automated}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=unload_state
	
	
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD=0
	
	RATOS_ECHO MSG="Filament unloading completed"

[gcode_macro _IDEX_UNLOAD_FILAMENT]
description = Unload filament macro for IDEX printer.
gcode = 
	
	{% set temp = params.TEMP|default(220)|int %}
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set enable_unload_tip_forming = true if printer["gcode_macro RatOS"].enable_unload_tip_forming|default(false)|lower == 'true' else false %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	RATOS_ECHO MSG="Unloading T{toolhead} filament..."
	
	DEBUG_ECHO PREFIX="_IDEX_UNLOAD_FILAMENT" MSG="TEMP: {temp}, TOOLHEAD: {toolhead}"
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set active_extruder = printer.toolhead.extruder %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	{% if not printer.pause_resume.is_paused %}
	{% if printer[target_extruder].temperature|int < temp or printer[target_extruder].can_extrude|lower == 'false' %}
	
	RATOS_ECHO MSG="Heating T{toolhead} to {temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	{% endif %}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={temp}
	{% endif %}
	
	
	G4 P3000
	
	
	{% if enable_unload_tip_forming %}
	_UNLOAD_FILAMENT TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}' AUTOMATED={automated}
	{% else %}
	_LEGACY_UNLOAD_FILAMENT TEMP={temp} TOOLHEAD={toolhead} AUTOMATED={automated}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={active_extruder}
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	RATOS_ECHO MSG="T{toolhead} filament unloading completed"

[gcode_macro _UNLOAD_FILAMENT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT" MSG="TOOLHEAD: {toolhead}"
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED={automated}
	_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER TOOLHEAD={toolhead}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}

[gcode_macro _LEGACY_UNLOAD_FILAMENT]
description = Unloads the filament. Note: be careful with PETG, make sure you inspect the tip of your filament before reloading to avoid jams.
gcode = 
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% set automated = params.AUTOMATED|default('false')|lower == 'true' %}
	
	{% set unload_speed = 5 * 60 %}
	{% set unload_length = printer["gcode_macro RatOS"].filament_unload_length|float %}
	M117 Unloading filament...
	
	G0 E10 F300
	
	G0 E-5 F3600
	
	G4 P3000
	
	G0 E5 F6000
	
	G0 E-15 F6000
	
	G0 E-{unload_length} F{unload_speed}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED={automated}
	M117 Filament unloaded!
	RESPOND MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_NOZZLE_TO_COOLING_ZONE" MSG="TOOLHEAD: {toolhead}"
	RATOS_ECHO MSG="Unloading filament from nozzle to cooling zone... Please wait!"
	
	_PURGE_BEFORE_UNLOAD TOOLHEAD={toolhead}
	
	{% if printer["gcode_macro _UNLOAD_WITHOUT_TIP_FORMING"] is defined %}
	
	_UNLOAD_WITHOUT_TIP_FORMING TOOLHEAD={toolhead} NAME='{filament_name}' TYPE='{filament_type}'
	{% else %}
	_UNLOAD_WITH_TIP_FORMING NAME='{filament_name}' TYPE='{filament_type}'
	{% endif %}
	
	G4 P3000

[gcode_macro _UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set extruder_load_speed = printer["gcode_macro T%s" % toolhead].extruder_load_speed|float * 60 %}
	{% set extruder_gear_to_cooling_position_distance = printer["gcode_macro T%s" % toolhead].extruder_gear_to_cooling_position_distance|float %}
	{% set tooolhead_sensor_to_extruder_gear_distance = printer["gcode_macro T%s" % toolhead].tooolhead_sensor_to_extruder_gear_distance|float %}
	
	DEBUG_ECHO PREFIX="_UNLOAD_FILAMENT_FROM_COOLING_ZONE_TO_EXTRUDER" MSG="TOOLHEAD: {toolhead}"
	
	
	G0 E-{extruder_gear_to_cooling_position_distance + tooolhead_sensor_to_extruder_gear_distance + 50} F{extruder_load_speed}
	
	RATOS_ECHO MSG="Filament unloaded! Please inspect the tip of the filament before reloading."

[gcode_macro _UNLOAD_WITH_TIP_FORMING]
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	{% if filament_name != '' and filament_type != '' %}
	_UNLOAD_KNOWN_FILAMENT NAME={filament_name} TYPE={filament_type}
	{% else %}
	_UNLOAD_UNKNOWN_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _UNLOAD_KNOWN_FILAMENT]
description = User overrideable tip forming macro if slicer filament profiles are known
gcode = 
	
	{% set filament_name = params.NAME|default('')|string %}
	{% set filament_type = params.TYPE|default('')|string %}
	
	
	RATOS_ECHO PREFIX="FILAMENT TYPE" MSG='{filament_type}'
	RATOS_ECHO PREFIX="FILAMENT PROFILE" MSG='{filament_name}'
	
	
	{% if filament_name == "Prusament PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% elif filament_name == "Nobufil PETG @V-Minion" %}
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10
	{% else %}
	
	RATOS_ECHO PREFIX="_UNLOAD_KNOWN_FILAMENT" MSG="Filament profile not found!"
	_UNLOAD_UNKNOWN_FILAMENT
	{% endif %}

[gcode_macro _UNLOAD_UNKNOWN_FILAMENT]
description = User overrideable standard tip forming macro
gcode = 
	
	DEBUG_ECHO PREFIX="_UNLOAD_UNKNOWN_FILAMENT" MSG="Using standard tip forming macro!"
	
	_TIP_FORMING RETRACT_LENGTH=18 COOLING_MOVE_LENGTH=10

[gcode_macro _TIP_FORMING]
gcode = 
	
	{% set cooling_moves = params.COOLING_MOVES|default(4)|int %}
	{% set cooling_move_length = params.COOLING_MOVE_LENGTH|default(10)|float %}
	{% set start_cooling_speed = params.START_COOLING_SPEED|default(10)|float * 60 %}
	{% set end_cooling_speed = params.END_COOLING_SPEED|default(50)|float * 60 %}
	{% if cooling_moves == 0 %}
	{% set cooling_move_length = 0 %}
	{% endif %}
	
	
	{% set dip = true if params.DIP|default(false)|lower == "true" else false %}
	{% set dip_length = params.DIP_LENGTH|default(22)|float %}
	{% set dip_speed = params.DIP_SPEED|default(30)|float * 60 %}
	{% set dip_retract_speed = params.DIP_RETRACT_SPEED|default(70)|float * 60 %}
	
	
	{% set retract_length = params.RETRACT_LENGTH|default(18)|float %}
	{% set start_retract_speed = params.START_RETRACT_SPEED|default(120)|float * 60 %}
	{% set end_retract_speed = params.END_RETRACT_SPEED|default(20)|float * 60 %}
	
	DEBUG_ECHO PREFIX="_TIP_FORMING" MSG="cooling_moves: {cooling_moves}, cooling_move_length: {cooling_move_length}, start_cooling_speed: {start_cooling_speed}, end_cooling_speed: {end_cooling_speed}, dip: {dip}, dip_length: {dip_length}, dip_speed: {dip_speed}, dip_retract_speed: {dip_retract_speed}, retract_length: {retract_length}, start_retract_speed: {start_retract_speed}, end_retract_speed: {end_retract_speed}"
	
	M220 S100
	
	
	G92 E0
	{% set retract = retract_length + cooling_move_length / 2 - 15 %}
	G1 E-15 F{start_retract_speed}
	G1 E-{0.7 * retract} F{1.0 * end_retract_speed}
	G1 E-{0.2 * retract} F{0.5 * end_retract_speed}
	G1 E-{0.1 * retract} F{0.3 * end_retract_speed}
	
	
	G92 E0
	{% if cooling_moves > 0 %}
	{% set i = (end_cooling_speed - start_cooling_speed) / (2 * cooling_moves - 1) %}
	{% for m in range(cooling_moves) %}
	G1 E{cooling_move_length} F{(start_cooling_speed + i * m * 2)}
	G1 E-{cooling_move_length} F{(start_cooling_speed + i * (m * 2 + 1))}
	{% endfor %}
	{% endif %}
	
	
	G92 E0
	{% if dip %}
	G1 E{dip_length} F{dip_speed}
	G4 P100
	G1 E-{dip_length} F{dip_retract_speed}
	{% endif %}
	
	G92 E0
	M400

[delayed_gcode __ON_FILAMENT_SENSOR_BUTTON_PRESSED_STARTUP_GUARD]
initial_duration = 2.
gcode = 
	SET_GCODE_VARIABLE MACRO=_ON_FILAMENT_SENSOR_BUTTON_PRESSED VARIABLE=startup_complete VALUE=True

[gcode_macro _ON_FILAMENT_SENSOR_BUTTON_PRESSED]
variable_startup_complete = False
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set toolhead_sensor_button_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_sensor_button_only_when_sensor_enabled|default(false)|lower == 'true' %}
	
	
	{% if not startup_complete and sensor_enabled %}
	{action_emergency_stop("RatOS: The T%s filament sensor button was triggered immediately on printer startup. This is likely a false trigger. Please check your filament sensor wiring and configuration!" % (toolhead,))}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_SENSOR_BUTTON_PRESSED" MSG="TOOLHEAD: {toolhead}, SENSOR_ENABLED: {sensor_enabled}, TOOLHEAD_SENSOR_BUTTON_ONLY_WHEN_SENSOR_ENABLED: {toolhead_sensor_button_only_when_sensor_enabled}"
	
	{% if not printer.virtual_sdcard.is_active and (sensor_enabled or not toolhead_sensor_button_only_when_sensor_enabled) %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead}
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_TOOLHEAD_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set sensor_enabled = printer["filament_switch_sensor toolhead_filament_sensor_t%s" % toolhead].enabled|lower == "true" %}
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	{% set toolhead_detect_clog_only_when_sensor_enabled = printer["gcode_macro T%s" % toolhead].toolhead_detect_clog_only_when_sensor_enabled|default(true)|lower == 'true' %}
	
	DEBUG_ECHO PREFIX="_ON_TOOLHEAD_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}, ENABLE_CLOG_DETECTION: {enable_clog_detection}, TOOLHEAD_DETECT_CLOG_ONLY_WHEN_SENSOR_ENABLED: {toolhead_detect_clog_only_when_sensor_enabled}, SENSOR_ENABLED: {sensor_enabled}"
	
	{% if enable_clog_detection and (sensor_enabled or not toolhead_detect_clog_only_when_sensor_enabled) %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_RUNOUT]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_runout_detection = true if printer["gcode_macro T%s" % toolhead].enable_runout_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_RUNOUT" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_runout_detection %}
	RATOS_ECHO MSG="Filament runout detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=false
	{% endif %}

[gcode_macro _ON_BOWDEN_FILAMENT_SENSOR_CLOG]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set enable_clog_detection = true if printer["gcode_macro T%s" % toolhead].enable_clog_detection|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_ON_BOWDEN_FILAMENT_SENSOR_CLOG" MSG="TOOLHEAD: {toolhead}"
	
	{% if enable_clog_detection %}
	RATOS_ECHO MSG="Filament clog or tangle detected on T{toolhead}!"
	_ON_FILAMENT_END TOOLHEAD={toolhead} CLOGGED=true
	{% endif %}

[gcode_macro _ON_FILAMENT_END]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set clogged = true if params.CLOGGED|default(false)|lower == 'true' else false %}
	
	
	{% set unload_after_runout = printer["gcode_macro T%s" % toolhead].unload_after_runout|float %}
	
	
	{% if clogged %}
	_LED_FILAMENT_CLOG TOOLHEAD={toolhead}
	{% else %}
	_LED_FILAMENT_RUNOUT TOOLHEAD={toolhead}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_ON_FILAMENT_END" MSG="TOOLHEAD: {toolhead}"
	
	{% if printer.virtual_sdcard.is_active %}
	{% if not printer.pause_resume.is_paused %}
	PAUSE RUNOUT=True
	{% endif %}
	{% if not clogged and unload_after_runout %}
	UNLOAD_FILAMENT TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	{% if not clogged and printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true'%}
	_JOIN_SPOOL TOOLHEAD={toolhead}
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro M600]
description = Executes a color change by pausing the printer an unloading the filament.
gcode = 
	PAUSE
	UNLOAD_FILAMENT AUTOMATED=True
	RATOS_ECHO MSG="Please load new filament and resume"

[gcode_macro COLD_PULL]
description = Automated hotend cold pull.
gcode = 
	
	{% set extrusion_temp = params.EXTRUSION_TEMP|default(220)|int %}
	{% set cold_pull_temp = params.COLD_PULL_TEMP|default(80)|int %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	
	{% if printer["dual_carriage"] is not defined %}
	{% set toolhead = 0 %}
	{% else %}
	{% if not printer.pause_resume.is_paused %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if current_idex_mode == 'copy' or current_idex_mode == 'mirror' %}
	{action_raise_error("Unloading filament in Copy or Mirror mode is not supported! Select single mode to proceed.")}
	{% else %}
	{% set paused_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% if paused_idex_mode == 'copy' or paused_idex_mode == 'mirror' %}
	{% set toolhead = params.TOOLHEAD|default(-1)|int %}
	{% else %}
	{% set toolhead = printer["gcode_macro PAUSE"].idex_toolhead|int %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% if toolhead != 0 and toolhead != 1 %}
	{action_raise_error("Please select toolhead! 0 = left, 1 = right toolhead")}
	{% endif %}
	{% endif %}
	
	{% if printer["dual_carriage"] is defined %}
	RATOS_ECHO MSG="Starting cold pull on T{toolhead}..."
	{% else %}
	RATOS_ECHO MSG="Starting cold pull..."
	{% endif %}
	
	
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	_LED_UNLOADING_FILAMENT TOOLHEAD={toolhead}
	
	
	SAVE_GCODE_STATE NAME=cold_pull_state
	
	
	{% if printer["dual_carriage"] is defined and "xyz" not in printer.toolhead.homed_axes %}
	_SELECT_TOOL T={toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	
	
	{% set target_extruder = 'extruder%s' % ('' if toolhead == 0 else toolhead) %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER={target_extruder}
	
	
	RATOS_ECHO MSG="Heating T{toolhead} to {extrusion_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={extrusion_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={extrusion_temp} MAXIMUM={extrusion_temp + 2}
	
	
	G4 P3000
	
	
	RATOS_ECHO MSG="extruding..."
	G92 E0
	G1 E30 F300
	G92 E0
	
	
	RATOS_ECHO MSG="Cooling T{toolhead} to {cold_pull_temp}C... Please wait."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={cold_pull_temp}
	TEMPERATURE_WAIT SENSOR={target_extruder} MINIMUM={cold_pull_temp} MAXIMUM={cold_pull_temp + 2}
	
	
	G4 P10000
	
	
	RATOS_ECHO MSG="cold pull..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-40 VELOCITY=5 ACCEL=100
	
	
	RATOS_ECHO MSG="eject filament..."
	FORCE_MOVE STEPPER={target_extruder} DISTANCE=-200 VELOCITY=20 ACCEL=500
	
	
	RATOS_ECHO MSG="cooling down extruder..."
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	RESTORE_GCODE_STATE NAME=cold_pull_state
	
	
	SAVE_VARIABLE VARIABLE=t{toolhead}_filament VALUE="('""', '""', 0)"
	{% if printer["gcode_macro T%s" % toolhead].filament_name is defined and printer["gcode_macro T%s" % toolhead].filament_type is defined and printer["gcode_macro T%s" % toolhead].filament_temp is defined %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=filament_temp VALUE=0
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=color VALUE='"{color_unknown}"'
	
	
	_LED_FILAMENT_UNLOADED TOOLHEAD={toolhead}
	
	
	CONSOLE_ECHO TITLE="Cold pull complete" MSG="Please remove the filament from the PTFE tube and cut the end off. Do NOT try to load it again." TYPE="warning"

[gcode_macro _USER_START_PRINT_BEFORE_HOMING]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_BED]
gcode = 

[gcode_macro _USER_START_PRINT_BED_MESH]
gcode = 

[gcode_macro _USER_START_PRINT_PARK]
gcode = 

[gcode_macro _USER_START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 

[gcode_macro _USER_START_PRINT_HEAT_CHAMBER]
description = Uses the extruder sensor to wait for chamber temp. Override the _START_PRINT_HEAT_CHAMBER macro to implement heated chamber handling.
gcode = 
	
	{% set chamber_heater_bed_temp = printer["gcode_macro RatOS"].chamber_heater_bed_temp|default(115)|int %}

[gcode_macro _USER_END_PRINT_BEFORE_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_AFTER_HEATERS_OFF]
gcode = 

[gcode_macro _USER_END_PRINT_PARK]
gcode = 

[gcode_macro _USER_END_PRINT_FINISHED]
description = User hook for when the print is finished after gcode state has been restored.
gcode = 

[gcode_macro _USER_START_PRINT]
gcode = 

[gcode_macro _USER_END_START_PRINT]
gcode = 

[gcode_macro _USER_START_FEATURE]
gcode = 

[gcode_macro _USER_END_FEATURE]
gcode = 

[gcode_macro _USER_BEFORE_IDLE_TIMEOUT]
gcode = 

[gcode_macro _USER_AFTER_IDLE_TIMEOUT]
gcode = 

[gcode_macro ECHO_T_VARS]
description = Echo Toolhead variables to the console.
gcode = 
	{% set t = params.T|default(0) %}
	RATOS_ECHO MSG="T{t} Variables"
	{% for var, value in printer["gcode_macro T%s" % t].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ECHO_RATOS_VARS]
description = Echo RatOS variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro RatOS"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro ENSURE_CRITICAL_RATOS_INIT]
variable_completed = False
gcode = 
	{% if not completed %}
	CALCULATE_PRINTABLE_AREA
	SET_GCODE_VARIABLE MACRO=ENSURE_CRITICAL_RATOS_INIT VARIABLE=completed VALUE=True
	{% endif %}

[delayed_gcode RATOS_INIT]
initial_duration = 0.1
gcode = 
	{action_respond_info("Initializing RatOS...")}
	ENSURE_CRITICAL_RATOS_INIT
	_LED_STANDBY
	INITIAL_FRONTEND_UPDATE
	_CHAMBER_FILTER_SANITY_CHECK
	{% if printer.fastconfig.settings.beacon is defined %}
	
	_BED_MESH_SANITY_CHECK
	{% endif %}
	{% set svv = printer.save_variables.variables %}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=0 C={svv.nozzle_expansion_coefficient_t0|default(0.06)|float}
	_NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK T=1 C={svv.nozzle_expansion_coefficient_t1|default(0.06)|float}
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=idex_applied_offset

[delayed_gcode RATOS_LOGO]
initial_duration = 2
gcode = 
	
	
	
	
	
	ENSURE_CRITICAL_RATOS_INIT
	HELLO_RATOS
	_ALERT_NON_ZERO_Z_OFFSET

[gcode_macro _ALERT_NON_ZERO_Z_OFFSET]
gcode = 
	{% set force = params.FORCE|default(0)|int == 1 %}
	{% set user_offset = printer.named_offsets.user_probe_z_offset.z|float %}
	{% set gcode_offset = printer.gcode_move.homing_origin.z|float %}
	{% set combined_offset = user_offset + gcode_offset %}
	
	{% if force or user_offset != 0 or gcode_offset != 0 %}
	{% set title = "User-adjusted Z-offset of %.3f mm is active" % combined_offset %}
	{% set msg = "" %}
	{% set nl = "" %}
	{% if user_offset != 0 %}
	{% set msg = msg + "beacon true zero user Z-offset: %.3f mm (to clear, use Z_OFFSET_APPLY_PROBE CLEAR=1)" % user_offset %}
	{% set nl = "_N_" %}
	{% endif %}
	{% if gcode_offset != 0 %}
	{% set msg = msg + nl + "G-code Z-offset: %.3f mm" % gcode_offset %}
	{% endif %}
	CONSOLE_ECHO TITLE="{title}" TYPE="info" MSG="{msg}"
	{% endif %}

[gcode_macro _INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE]
gcode = 
	{% set variable = params.VARIABLE|string %}
	{% set svv = printer.save_variables.variables %}
	{% set nlu_msg = "no longer used, please remove" %}
	{% if svv[variable] is defined %}
	{% set v = svv[variable]|string|replace('"', '')|replace("'", "") %}
	{% if not nlu_msg in v %}
	SAVE_VARIABLE VARIABLE={variable} VALUE='"{nlu_msg} (was {v})"'
	{% endif %}
	CONSOLE_ECHO TITLE="Deprecated ratos-variables.cfg variable" TYPE="warning" MSG="The variable {variable} is no longer used, please remove it from your ratos-variables.cfg file."
	{% endif %}

[gcode_macro _NOZZLE_EXPANSION_COEFFICIENT_SANITY_CHECK]
gcode = 
	
	
	
	
	
	
	
	{% set t = params.T|int %}
	{% set c = params.C|float %}
	{% set normal_low = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_low|default(0.05)|float %}
	{% set normal_high = printer["gcode_macro RatOS"].sanity_check_nozzle_expansion_coefficient_high|default(0.10)|float %}
	
	{% if c < 0 %}
	
	{action_emergency_stop("Invalid nozzle_expansion_coefficient_t%s value in ratos-variables.cfg: %.3f. It must be non-negative." % (t, c))}
	{% endif %}
	{% if c >= normal_high %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite high. Please verify that this is correct."
	{% endif %}
	{% if c <= normal_low %}
	CONSOLE_ECHO TITLE="Suspicious nozzle expansion coefficient for T{t} value" TYPE="warning" MSG="The nozzle_expansion_coefficient_t{t} value in ratos-variables.cfg is {c|round(3)}, which is quite low. Please verify that this is correct."
	{% endif %}

[gcode_macro INITIAL_FRONTEND_UPDATE]
gcode = 
	
	{% set color_ok = printer["gcode_macro RatOS"].status_color_ok|string %}
	{% set color_error = printer["gcode_macro RatOS"].status_color_error|string %}
	{% set color_unknown = printer["gcode_macro RatOS"].status_color_unknown|string %}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_unknown}"'
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_unknown}"'
	{% endif %}
	
	
	{% set t0_sensor = "undefined" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	{% set t0_sensor = "detected" %}
	{% else %}
	{% set t0_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t0_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	{% set t1_sensor = "undefined" %}
	{% if printer["dual_carriage"] is defined and printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	{% set t1_sensor = "detected" %}
	{% else %}
	{% set t1_sensor = "empty" %}
	{% endif %}
	{% else %}
	{% set t1_sensor = "disabled" %}
	{% endif %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	{% if svv.t0_filament is defined and printer["gcode_macro T0"] is defined %}
	{% if printer["gcode_macro T0"].filament_name is defined and printer["gcode_macro T0"].filament_type is defined and printer["gcode_macro T0"].filament_temp is defined %}
	{% if t0_sensor != "empty" %}
	{% set t0_filament_type = svv.t0_filament[0]|default('')|string %}
	{% set t0_filament_name = svv.t0_filament[1]|default('')|string %}
	{% set t0_filament_temp = svv.t0_filament[2]|default(0)|float %}
	{% if t0_filament_name != '' and t0_filament_type != '' and t0_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='"{t0_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='"{t0_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE={t0_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t0_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}
	{% if svv.t1_filament is defined and printer["gcode_macro T1"] is defined %}
	{% if printer["gcode_macro T1"].filament_name is defined and printer["gcode_macro T1"].filament_type is defined and printer["gcode_macro T1"].filament_temp is defined %}
	{% if t1_sensor != "empty" %}
	{% set t1_filament_type = svv.t1_filament[0]|default('')|string %}
	{% set t1_filament_name = svv.t1_filament[1]|default('')|string %}
	{% set t1_filament_temp = svv.t1_filament[2]|default(0)|float %}
	{% if t1_filament_name != '' and t1_filament_type != '' and t1_filament_temp > 0 %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=color VALUE='"{color_ok}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='"{t1_filament_name}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='"{t1_filament_type}"'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE={t1_filament_temp}
	{% endif %}
	{% else %}
	SAVE_VARIABLE VARIABLE=t1_filament VALUE="('""', '""', 0)"
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_name VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_type VALUE='""'
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=filament_temp VALUE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro CALCULATE_PRINTABLE_AREA]
variable_calculated = False
gcode = 
	{% if not calculated %}
	{% set bed_margin_x = printer["gcode_macro RatOS"].bed_margin_x %}
	{% set bed_margin_y = printer["gcode_macro RatOS"].bed_margin_y %}
	
	
	
	{% set tool = 0 if printer["gcode_macro T0"] is not defined or printer["gcode_macro T0"].active else 1 %}
	{% set max_x = printer.toolhead.axis_maximum.x if printer["dual_carriage"] is defined and tool == 0 else printer.toolhead.axis_maximum.x - bed_margin_x[1] %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	
	
	{% set max_x = printer.toolhead.axis_maximum.x %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="printer.toolhead.axis_maximum.x {printer.toolhead.axis_maximum.x}"
	
	{% set max_y = printer.toolhead.axis_maximum.y - bed_margin_y[1]%}
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_x_max VALUE={max_x}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=printable_y_max VALUE={max_y}
	SET_GCODE_VARIABLE MACRO=CALCULATE_PRINTABLE_AREA VARIABLE=calculated VALUE=True
	
	DEBUG_ECHO PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	RATOS_LOG PREFIX="CALCULATE_PRINTABLE_AREA" MSG="Printable area calculated: X: 0,{max_x} Y: 0,{max_y}"
	{% endif %}

[gcode_macro CACHE_TOOLHEAD_SETTINGS]
variable_cache = {"global": {"accel": 1000, "ratio": 0.5, "speed": 50, "scv": 5}}
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set dummy = cache.__setitem__(key, {"accel": printer.toolhead.max_accel, "ratio": printer.toolhead.minimum_cruise_ratio, "speed": printer.toolhead.max_velocity, "scv": printer.toolhead.square_corner_velocity}) %}
	SET_GCODE_VARIABLE MACRO=CACHE_TOOLHEAD_SETTINGS VARIABLE=cache VALUE="{cache | pprint | replace("\n", "") | replace("\"", "\\\"")}"
	DEBUG_ECHO PREFIX="CACHE_TOOLHEAD_SETTINGS" MSG="Toolhead settings cached for {key}. {printer.toolhead.max_accel} accel, {printer.toolhead.minimum_cruise_ratio} ratio, {printer.toolhead.max_velocity} velocity, {printer.toolhead.square_corner_velocity} scv."

[gcode_macro RESTORE_TOOLHEAD_SETTINGS]
gcode = 
	
	{% set key = "global" %}
	{% if params.KEY is defined %}
	{% set key = params.KEY %}
	{% endif %}
	{% set values = printer["gcode_macro CACHE_TOOLHEAD_SETTINGS"].cache.__getitem__(key) %}
	{% if values is not defined or values == 'None' %}
	{ action_raise_error("RESTORE_TOOLHEAD_SETTINGS: Toolhead settings not cached for key '" ~ key ~ "'.") }
	{% endif %}
	SET_VELOCITY_LIMIT ACCEL={values.accel} MINIMUM_CRUISE_RATIO={values.ratio} VELOCITY={values.speed} SQUARE_CORNER_VELOCITY={values.scv}
	DEBUG_ECHO PREFIX="RESTORE_TOOLHEAD_SETTINGS" MSG="Toolhead settings restored. {values.accel} accel, {values.ratio} ratio, {values.speed} velocity, {values.scv} scv."

[gcode_macro SET_MACRO_TRAVEL_SETTINGS]
gcode = 
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float %}
	{% set accel = printer["gcode_macro RatOS"].macro_travel_accel %}
	SET_VELOCITY_LIMIT ACCEL={accel} MINIMUM_CRUISE_RATIO=0.5 VELOCITY={speed} SQUARE_CORNER_VELOCITY={5}
	DEBUG_ECHO PREFIX="SET_MACRO_TRAVEL_SETTINGS" MSG="Macro travel settings set. {accel} accel, {speed} velocity"

[gcode_macro SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% if printer["dual_carriage"] is not defined %}
	
	SET_KINEMATIC_POSITION X={printable_x_max / 2} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	{% else %}
	
	IDEX_SET_CENTER_KINEMATIC_POSITION
	{% endif %}

[gcode_macro IDEX_SET_CENTER_KINEMATIC_POSITION]
description = FOR DEBUGGING PURPOSES ONLY. Sets the internal printer kinematic state to the center of all axes regardless of actual physical position.
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	RATOS_ECHO MSG="WARNING: ONLY USE SET_CENTER_KINEMATIC_POSITION FOR DEBUGGING PURPOSES. YOU'RE OVERRIDING THE INTERNAL POSITIONING STATE OF THE PRINTER. PROCEED WITH CAUTION AND DO A PROPER G28 WHEN DONE."
	SET_GCODE_VARIABLE MACRO=MAYBE_HOME VARIABLE=is_kinematic_position_overriden VALUE=True
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x - (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	SET_KINEMATIC_POSITION X={center_x + (center_x / 2)} Y={printable_y_max / 2} Z={printer.toolhead.axis_maximum.z / 2}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY

[gcode_macro VERIFY_HYBRID_INVERTED]
gcode = 
	
	{% set inverted = False %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy is defined and printer.fastconfig.settings.ratos_hybrid_corexy.inverted is defined %}
	{% if printer.fastconfig.settings.ratos_hybrid_corexy.inverted|lower == 'true' %}
	{% set inverted = True %}
	{% endif %}
	{% endif %}
	{% if inverted == False %}
	{ action_emergency_stop("ratos_hybrid_corexy NOT INVERTED! Inverted hybrid core-xy bugfix not detected.") }
	{% endif %}

[gcode_macro RATOS_ECHO]
gcode = 
	{% set prefix = "RatOS" %}
	{% set debug = params.DEBUG|default(0)|int %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " | " ~ params.PREFIX %}
	{% endif %}
	{% set prefix = prefix ~ ":" %}
	{% set msg = "" %}
	{% if params.MSG is defined %}
	{% set msg = params.MSG %}
	{% else %}
	{% set msg = "No msg parameter provided (this is a bug or unintended use)." %}
	{% endif %}
	{% if not debug %}
	
	M117 {prefix} {msg}
	{% endif %}
	RATOS_LOG PREFIX="{prefix}" MSG="{msg}"
	{% if not debug %}
	RESPOND PREFIX="{prefix}" MSG="{msg}"
	{% else %}
	CONSOLE_ECHO TITLE="{prefix}" TYPE="debug" MSG="{msg}"
	{% endif %}

[gcode_macro ENABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=True
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=prefix_filter VALUE="'{params.FILTER|default('')|lower}'"
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging enabled."

[gcode_macro DISABLE_DEBUG]
gcode = 
	SET_GCODE_VARIABLE MACRO=DEBUG_ECHO VARIABLE=enabled VALUE=False
	RATOS_ECHO PREFIX="DEBUG" MSG="Debugging disabled."

[gcode_macro DEBUG_ECHO]
variable_enabled = False
variable_prefix_filter = ''
gcode = 
	{% set prefix = "DEBUG" %}
	{% if params.PREFIX is defined %}
	{% set prefix = prefix ~ " - " ~ params.PREFIX %}
	{% endif %}
	{% if enabled and (prefix_filter|lower == '' or prefix_filter|lower in params.PREFIX|lower) %}
	RATOS_ECHO PREFIX="{prefix}" MSG="{params.MSG}" DEBUG=1
	{% endif %}

[gcode_macro START_FEATURE]
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="Start {params.FEATURE} feature gcode"
	{% set scv = printer.toolhead.square_corner_velocity|int|default(5) %}
	{% set accel = printer.toolhead.max_accel|int|default(10000) %}
	{% set ratio = printer.toolhead.minimum_cruise_ratio|float|default(0.5) %}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="scv" VALUE={scv}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="accel" VALUE={accel}
	SET_GCODE_VARIABLE MACRO="END_FEATURE" VARIABLE="ratio" VALUE={ratio}
	_USER_START_FEATURE FEATURE="{params.FEATURE}"

[gcode_macro END_FEATURE]
variable_scv = 5
variable_accel = 10000
variable_ratio = 0.5
gcode = 
	DEBUG_ECHO PREFIX="G-Code" MSG="End {params.FEATURE} feature gcode"
	SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY={scv} ACCEL={accel} MINIMUM_CRUISE_RATIO={ratio}
	_USER_END_FEATURE FEATURE="{params.FEATURE}" SCV={scv} ACCEL={accel} RATIO={ratio}

[gcode_macro _ON_LAYER_CHANGE]
variable_layer_number = 0
description = INTERNAL USE ONLY. Call it from the slicers after layer change custom gcode
gcode = 
	
	{% set layer = params.LAYER|int %}
	
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE={layer}
	SET_PRINT_STATS_INFO CURRENT_LAYER={layer}

[gcode_macro _LEARN_MORE_CALIBRATION]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/calibration" %}
	{% set link_text = "RatOS Calibration Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_CHAMBER_FILTER]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/chamber_filter" %}
	{% set link_text = "RatOS Chamber Filter Control" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _LEARN_MORE_FILAMENT]
gcode = 
	{% set link_url = "https://os.ratrig.com/docs/configuration/filaments" %}
	{% set link_text = "RatOS Filament Macros" %}
	{% set line_1 = '"Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="INFO" MSG={line_1}

[gcode_macro _CONSOLE_SAVE_CONFIG]
gcode = 
	M118 Click <a class="command text--blue">SAVE_CONFIG</a> to save the settings to your printer.cfg.

[gcode_macro _LOAD_RATOS_SKEW_PROFILE]
gcode = 
	{% set ratos_skew_profile = printer["gcode_macro RatOS"].skew_profile|default("") %}
	{% if ratos_skew_profile != "" %}
	{% if printer.fastconfig.config["skew_correction %s" % ratos_skew_profile] is defined %}
	SKEW_PROFILE LOAD={ratos_skew_profile}
	GET_CURRENT_SKEW
	{% else %}
	{% set line_1 = '"Could not find skew profile %s!_N_Clearing skew correction."' % ratos_skew_profile %}
	CONSOLE_ECHO TITLE="Missing skew profile!" TYPE="warning" MSG={line_1}
	SET_SKEW CLEAR=1
	{% endif %}
	{% endif %}

[gcode_macro M601]
gcode = 
	PAUSE

[gcode_macro _STOP_AND_RAISE_ERROR]
gcode = 
	M84
	_RAISE_ERROR MSG="{params.MSG}"

[gcode_macro _RESET_GCODE_VARIABLES]
description = Reset specified [gcode_macro ...] variables to their original values from configuration when Klipper started.
	- MACRO: Name of the GCODE macro containing the variables to reset.
	- VARIABLES: Comma-separated list of variable names to reset (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- QUIET: (optional) If true, suppresses console echo messages for each reset variable. Default is false.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set quiet = params.QUIET|default("false")|lower in ("true", "1", "yes") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	{% set settings = printer.fastconfig.settings[obj_name|lower] %}
	{% if settings is not defined %}
	{ action_raise_error("No settings found for [gcode_macro %s]" % macro) }
	{% endif %}
	
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if settings["variable_%s" % var] is not defined %}
	{ action_raise_error("Variable '%s' is not defined in settings for [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	
	{% for var in vars %}
	{% set var_value = obj[var] %}
	{% if var_value is defined %}
	{% set v = settings["variable_%s" % var] %}
	{% if v != var_value|string %}
	{% if var_value is string %}
	{% set v = '"\'' ~ v|replace('"', '\\"')|replace("'", "\\'") ~ '\'"' %}
	{% endif %}
	SET_GCODE_VARIABLE MACRO={macro} VARIABLE={var} VALUE={v}
	{% if not quiet %}
	CONSOLE_ECHO MSG="Reset {macro} variable {var} to original value: {v} (was {obj[var]})"
	{% endif %}
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro _SHOW_GCODE_VARIABLES]
description = Show current values of specified [gcode_macro ...] variables.
	- MACRO: Name of the GCODE macro containing the variables to show.
	- VARIABLES: Comma-separated list of variable names to show (do not include the "variable_" prefix).
	- SKIP_UNDEFINED_VARIABLES: (optional) If true, skips variables that are not defined in the macro without raising an error. Default is false.
	- PAD: (optional) If defined, provide a single character to use for padding variable names to align values in a tabular format in the console output. Default is no padding.
gcode = 
	{% set macro = params.MACRO|trim() %}
	{% set vars = params.VARIABLES.split(",") %}
	{% set skip_undefined_vars = params.SKIP_UNDEFINED_VARIABLES|default("false")|lower in ("true", "1", "yes") %}
	{% set pad = params.PAD|default("") %}
	{% set obj_name = "gcode_macro %s" % macro %}
	{% set obj = printer[ obj_name ] %}
	{% if obj is not defined %}
	{ action_raise_error("[gcode_macro %s] is not defined" % macro) }
	{% endif %}
	
	{% set ns = namespace() %}
	{% set ns.max_len = 0 %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% set ns.max_len = (ns.max_len, var|length)|max %}
	{% else %}
	{% if not skip_undefined_vars %}
	{ action_raise_error("Variable '%s' is not defined in [gcode_macro %s]" % (var, macro)) }
	{% endif %}
	{% endif %}
	{% endfor %}
	{% for var in vars %}
	{% if obj[var] is defined %}
	{% if pad %}
	{% set padding = pad * (ns.max_len - var|length) %}
	CONSOLE_ECHO MSG="{var}{padding} {obj[var]}"
	{% else %}
	CONSOLE_ECHO MSG="{var}: {obj[var]}"
	{% endif %}
	{% endif %}
	{% endfor %}

[gcode_macro PAUSE]
description = Pauses the print
rename_existing = PAUSE_BASE
variable_extrude = 1.5
variable_retract = 1.5
variable_fan_speed = 0
variable_idex_mode = ""
variable_idex_toolhead = 0
variable_idex_toolhead_x = 0.0
variable_idex_toolhead_y = 0.0
variable_idex_toolhead_z = 0.0
gcode = 
	RATOS_ECHO MSG="Pausing print..."
	
	
	{% set runout_detected = true if params.RUNOUT|default(false)|lower == 'true' else false %}
	
	
	_LED_PAUSE
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	SAVE_GCODE_STATE NAME=PAUSE_state
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_mode VALUE='"{idex_mode}"'
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={idex_toolhead}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_x VALUE={printer.gcode_move.gcode_position.x|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_y VALUE={printer.gcode_move.gcode_position.y|float}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead_z VALUE={printer.gcode_move.gcode_position.z|float}
	DEBUG_ECHO PREFIX="PAUSE" MSG="idex_mode: {idex_mode}, idex_toolhead: {idex_toolhead}, idex_toolhead_x: {idex_toolhead_x}, idex_toolhead_y: {idex_toolhead_y}, idex_toolhead_z: {idex_toolhead_z}"
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="pause"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% if current_z < (max_z - 20.0) %}
	{% set z_safe = 20.0 %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	PAUSE_BASE
	
	
	{% if printer["dual_carriage"] is not defined %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan"].speed|float}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	{% if idex_toolhead == 0 %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t0"].speed|float}
	{% else %}
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=fan_speed VALUE={printer["fan_generic part_fan_t1"].speed|float}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106 S0
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set R = printer["gcode_macro PAUSE"].retract|float %}
	{% if can_extrude %}
	G91
	G1 E-{R} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	{% set pause_print_park_x = printer["gcode_macro RatOS"].pause_print_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].pause_print_park_in %}
	{% if runout_detected %}
	{% set pause_print_park_x = printer["gcode_macro RatOS"].runout_park_x %}
	{% set pause_print_park_in = printer["gcode_macro RatOS"].runout_park_in %}
	{% endif %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	DEBUG_ECHO PREFIX="PAUSE" MSG="z_speed: {z_speed}, pause_print_park_x: {pause_print_park_x}, pause_print_park_in: {pause_print_park_in}, default_toolhead: {default_toolhead}"
	{% if "xyz" in printer.toolhead.homed_axes %}
	G91
	G1 Z{z_safe} F{z_speed}
	G90
	{% if printer["dual_carriage"] is not defined %}
	
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% else %}
	
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	_IDEX_SINGLE X={parking_position}
	{% else %}
	PARK_TOOLHEAD
	{% endif %}
	_PARK LOCATION={pause_print_park_in} X={pause_print_park_x}
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="pause"
	
	RATOS_ECHO MSG="Print paused"

[gcode_macro RESUME]
description = Resumes the print if the printer is paused.
rename_existing = RESUME_BASE
gcode = 
	
	
	RATOS_ECHO MSG="Resuming print..."
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	
	{% set target_idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set target_idex_mode = printer["gcode_macro PAUSE"].idex_mode|lower %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if target_idex_mode != '' %}
	{% if target_idex_mode == 'copy' or target_idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set fan_speed = printer["gcode_macro PAUSE"].fan_speed|float %}
	{% if printer["dual_carriage"] is not defined %}
	M106 S{(fan_speed * 255)}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% else %}
	{% if params.TOOLHEAD is defined %}
	
	{% if params.TOOLHEAD == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% else %}
	{% if printer["gcode_macro PAUSE"].idex_toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed}
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if target_idex_mode == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif target_idex_mode == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	{% if params.TOOLHEAD is defined %}
	_SELECT_TOOL T={params.TOOLHEAD} X=-1 Y=-1 TOOLSHIFT=false
	{% else %}
	_SELECT_TOOL T={printer["gcode_macro PAUSE"].idex_toolhead} X=-1 Y=-1 TOOLSHIFT=false
	{% endif %}
	{% endif %}
	
	{% set x = printer["gcode_macro PAUSE"].idex_toolhead_x|float %}
	{% set y = printer["gcode_macro PAUSE"].idex_toolhead_y|float %}
	{% set z = printer["gcode_macro PAUSE"].idex_toolhead_z|float %}
	G1 X{x} Y{y} Z{z} F{speed}
	{% if params.TOOLHEAD is defined %}
	
	SAVE_GCODE_STATE NAME=PAUSE_STATE
	{% endif %}
	{% endif %}
	
	
	{% if params.TOOLHEAD is not defined %}
	{% set E = printer["gcode_macro PAUSE"].extrude|float %}
	{% if can_extrude %}
	G91
	G1 E{E} F2100
	G90
	{% else %}
	{action_respond_info("Extruder not hot enough")}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined %}
	RESTORE_GCODE_STATE NAME=PAUSE_state MOVE=1 MOVE_SPEED={speed}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	RESUME_BASE
	
	
	_LED_PRINTING
	
	RATOS_ECHO MSG="Print resumed"

[gcode_macro CANCEL_PRINT]
description = Cancels the print
rename_existing = CANCEL_PRINT_BASE
gcode = 
	RATOS_ECHO MSG="Cancelling print..."
	END_PRINT
	TURN_OFF_HEATERS
	CLEAR_PAUSE
	
	CANCEL_PRINT_BASE
	RATOS_ECHO MSG="Print cancelled"

[gcode_macro START_PRINT]
description = Start print procedure, use this in your Slicer.
variable_post_processor_version = 2
variable_is_printing_gcode = False
variable_both_toolheads = True
variable_object_xoffset = 0
variable_first_x = -1
variable_first_y = -1
variable_total_toolshifts = 0
variable_initial_tool = 0
variable_extruder_first_layer_temp = ""
variable_extruder_other_layer_temp = ""
gcode = 
	
	{% if params.EXTRUDER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_TEMP parameter not found.")}
	{% endif %}
	{% if params.EXTRUDER_OTHER_LAYER_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. EXTRUDER_OTHER_LAYER_TEMP parameter not found.")}
	{% endif %}
	{% if params.BED_TEMP is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Missing START_PRINT parameter. BED_TEMP parameter not found.")}
	{% endif %}
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' and printer["gcode_macro RatOS"].danger_force_allow_auto_center_subject|default(false)|lower != 'true'%}
	
	
	
	
	
	{ action_raise_error("The experimental auto_center_subject feature is not supported in this version of RatOS. Please disable it in the RatOS macro settings.") }
	{% endif %}
	
	
	{% if "xyz" in printer.toolhead.homed_axes and printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% if printer["gcode_macro _VAOC"].is_started|default(true)|lower == 'true' %}
	_VAOC_END
	{% endif %}
	{% endif %}
	
	
	_LED_START_PRINTING
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_USER_START_PRINT { rawparams }
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_probe_stowable = printer["gcode_macro RatOS"].z_probe|lower == 'stowable' %}
	{% if printer["dual_carriage"] is defined %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	{% endif %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	{% set X0 = params.X0|default(-1)|float %}
	{% set X1 = params.X1|default(-1)|float %}
	{% set Y0 = params.Y0|default(-1)|float %}
	{% set Y1 = params.Y1|default(-1)|float %}
	{% if first_x == -1 or first_y == -1 %}
	{% set first_x = params.FIRST_X|default(-1)|float %}
	{% set first_y = params.FIRST_Y|default(-1)|float %}
	{% endif %}
	{% set total_toolshifts = params.TOTAL_TOOLSHIFTS|default(0)|int %}
	{% set initial_tool = params.INITIAL_TOOL|default(default_toolhead)|int %}
	{% set start_chamber_temp = params.START_CHAMBER_TEMP|default(0)|int %}
	
	
	
	
	
	
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(printer.heater_bed.target, true)|float %}
	
	
	{% set total_layer_count = params.TOTAL_LAYER_COUNT|default(0)|int %}
	{% set extruder_first_layer_temp = (params.EXTRUDER_TEMP|default("")).split(",") %}
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL BEACON_CONTACT_START_PRINT_TRUE_ZERO={beacon_contact_start_print_true_zero} BEACON_CONTACT_CALIBRATE_MODEL_ON_TRUE_ZERO={beacon_contact_calibrate_model_on_true_zero}
	{% endif %}
	
	_START_PRINT_PREFLIGHT_CHECK_AND_RESET_BED_MESH BED_TEMP={bed_temp}
	
	
	RATOS_ECHO MSG="First print coordinates X:{first_x} Y:{first_y}"
	
	
	{% if params.TOTAL_LAYER_COUNT is not defined %}
	{% set link_url = "https://os.ratrig.com/docs/slicers" %}
	{% set link_text = "RatOS Slicer Configuration" %}
	{% set line_1 = '"Your slicer gcode settings are not up to date._N_Learn more about the <a href="%s" target="_blank" >%s</a>"' % (link_url, link_text) %}
	CONSOLE_ECHO TITLE="Incomplete Slicer Configuration detected" TYPE="warning" MSG={line_1}
	{% endif %}
	
	
	SET_PRINT_STATS_INFO CURRENT_LAYER=1
	SET_GCODE_VARIABLE MACRO=_ON_LAYER_CHANGE VARIABLE=layer_number VALUE=1
	{% if total_layer_count > 0 %}
	SET_PRINT_STATS_INFO TOTAL_LAYER={total_layer_count}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads %}
	{% set initial_tool = 0 if initial_tool == 1 else 1 %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	{% endif %}
	
	
	{% set both_toolheads = true %}
	{% if total_toolshifts == 0 %}
	{% set both_toolheads = false %}
	{% endif %}
	
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	_IDEX_SINGLE X={parking_position}
	{% endif %}
	{% if both_toolheads and (idex_mode == "copy" or idex_mode == "mirror") %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Gcode tool changes found. Copy and mirror mode do not support toolchanges.")}
	{% endif %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set both_toolheads = true %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=initial_tool VALUE={initial_tool}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_x VALUE={first_x}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=first_y VALUE={first_y}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=total_toolshifts VALUE={total_toolshifts}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=both_toolheads VALUE={both_toolheads}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_first_layer_temp VALUE="'{params.EXTRUDER_TEMP}'"
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=extruder_other_layer_temp VALUE="'{params.EXTRUDER_OTHER_LAYER_TEMP}'"
	
	
	{% if printer["dual_carriage"] is defined %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE=0
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set svv = printer.save_variables.variables %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set stepper_x_position_min = printer.fastconfig.settings.stepper_x.position_min|float %}
	{% set stepper_x_position_endstop = printer.fastconfig.settings.stepper_x.position_endstop|float %}
	{% set dual_carriage_position_max = printer.fastconfig.settings.dual_carriage.position_max|float %}
	{% set dual_carriage_position_endstop = printer.fastconfig.settings.dual_carriage.position_endstop|float %}
	{% set x_parking_space = parking_position_t0 - (stepper_x_position_endstop , stepper_x_position_min)|max %}
	{% set dc_parking_space = (dual_carriage_position_endstop , dual_carriage_position_max)|min - parking_position_t1 %}
	{% if svv.idex_xoffset|abs >= (x_parking_space - 0.5) or svv.idex_xoffset|abs >= (dc_parking_space - 0.5) %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Toolhead x-offset is too high for the available parking space. Calibrate your X and DC endstop positions and make sure you stay below 1mm." % (copy_mode_max_width)) }
	{% endif %}
	{% endif %}
	
	
	{% if (idex_mode == "copy" or idex_mode == "mirror") and printer.fastconfig.settings.ratos.enable_gcode_transform %}
	
	{% if params.MIN_X is not defined or params.MAX_X is not defined %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Something went wrong! Missing important post processor start print parameter!") }
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE=0
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	
	{% set boundary_box_min_x = params.MIN_X|default(0)|float %}
	{% set boundary_box_max_x = params.MAX_X|default(printable_x_max)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if default_toolhead == 0 %}
	
	{% set boundary_box_max_x = boundary_box_max_x + svv.idex_xoffset %}
	{% else %}
	
	{% set boundary_box_min_x = boundary_box_min_x - svv.idex_xoffset %}
	{% endif %}
	
	{% set center_x = printable_x_max / 2.0 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set object_width = boundary_box_max_x - boundary_box_min_x %}
	{% set copy_mode_max_width = center_x %}
	{% set mirror_mode_max_width = center_x - safe_distance / 2.0 %}
	
	DEBUG_ECHO PREFIX="START_PRINT" MSG="OBJECT_WIDTH: {object_width} BOUNDARY_BOX_MIN_X: {boundary_box_min_x} BOUNDARY_BOX_MAX_X: {boundary_box_max_x} CENTER_X: {center_x} SAFE_DISTANCE: {safe_distance}"
	
	
	{% if idex_mode == "copy" and object_width > copy_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for copy mode! Max supported width is %s mm" % (copy_mode_max_width)) }
	{% endif %}
	{% if idex_mode == "mirror" and object_width > mirror_mode_max_width %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Object is too big for mirror mode! Max supported width is %s mm" % (mirror_mode_max_width)) }
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = (printable_x_max - boundary_box_max_x - boundary_box_min_x) / 2 %}
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=object_xoffset VALUE={object_xoffset}
	{% endif %}
	
	{% endif %}
	
	
	{% set has_initial_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_toolhead_filament_sensor %}
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% set has_initial_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool] is defined else false %}
	{% if has_initial_bowden_filament_sensor %}
	
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % initial_tool].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (initial_tool)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% if printer["dual_carriage"] is defined and both_toolheads %}
	
	{% set has_secondary_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s filament sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	
	{% set has_secondary_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)] is defined else false %}
	{% if has_secondary_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % (1 if initial_tool == 0 else 0)].filament_detected|lower != "true" %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("Filament not detected! Toolhead T%s bowden sensor is empty." % (1 if initial_tool == 0 else 0)) }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_CHAMBER_FILTER_ON AT="before_print_start"
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if printer["gcode_macro _IDEX_JOIN_SPOOLS"].enabled|default(false)|lower == 'true' %}
	{% if both_toolheads %}
	RATOS_ECHO MSG="Spool join is not possible if both toolheads are in use!"
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	{% endif %}
	
	
	CLEAR_PAUSE
	{% if printer["gcode_macro RatOS"].force_absolute_position|lower == 'true' %}
	G90
	{% endif %}
	SAVE_GCODE_STATE NAME=start_print_state
	
	
	G21
	
	G90
	
	M82
	_USER_START_PRINT_BEFORE_HOMING { rawparams }
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_BEGIN_BATCH
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_Z_HOP
	
	
	{% if idex_mode != '' and not (printer.fastconfig.settings.beacon is defined and (beacon_contact_start_print_true_zero or beacon_adaptive_heat_soak)) %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	{% if chamber_temp > 0 %}
	{% if printer["fan_generic filter"] is defined %}
	{% if printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float > 0 %}
	SET_FAN_SPEED FAN=filter SPEED={printer["gcode_macro RatOS"].chamber_heater_filter_fan_speed|default(0)|float}
	{% endif %}
	{% endif %}
	_CHAMBER_HEATER_ON START_CHAMBER_TEMP={start_chamber_temp} CHAMBER_TEMP={chamber_temp}
	_USER_START_PRINT_HEAT_CHAMBER { rawparams } CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_START_PRINT_BEFORE_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	RATOS_ECHO MSG="Heating bed..."
	
	M190 S{bed_temp}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_adaptive_heat_soak %}
	_MOVE_TO_SAFE_Z_HOME
	
	G1 Z2.5 F{z_speed}
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK LAYER_QUALITY={beacon_adaptive_heat_soak_layer_quality} MAXIMUM_FIRST_LAYER_DURATION={beacon_adaptive_heat_soak_maximum_first_layer_duration} MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={beacon_adaptive_heat_soak_max_wait}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_BED { rawparams }
	
	
	_START_PRINT_AFTER_HEATING_BED T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	_USER_START_PRINT_BED_MESH { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_BED_MESH X0={X0} X1={X1} Y0={Y0} Y1={Y1} T={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if z_probe_stowable == true %}
	STOWABLE_PROBE_END_BATCH
	{% endif %}
	
	
	{% if idex_mode == '' %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[initial_tool]|float}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={extruder_first_layer_temp[0]|float}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={extruder_first_layer_temp[1]|float}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_PARK { rawparams }
	
	
	_START_PRINT_PARK
	
	
	RATOS_ECHO MSG="Heating Extruder..."
	{% if idex_mode == '' %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[initial_tool]|float}  MAXIMUM={extruder_first_layer_temp[initial_tool]|float + 5}
	{% else %}
	{% if initial_tool == 0 or both_toolheads or (default_toolhead == 0 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder" MINIMUM={extruder_first_layer_temp[0]|float}  MAXIMUM={extruder_first_layer_temp[0]|float + 5}
	{% endif %}
	{% if initial_tool == 1 or both_toolheads or (default_toolhead == 1 and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	TEMPERATURE_WAIT SENSOR="extruder1" MINIMUM={extruder_first_layer_temp[1]|float}  MAXIMUM={extruder_first_layer_temp[1]|float + 5}
	{% endif %}
	{% endif %}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	{% if idex_mode == '' %}
	_LED_PRINTING
	{% else %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	_LED_PRINTING
	{% else %}
	{% if both_toolheads %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	{% if toolchange_standby_temp > -1 %}
	_LED_TOOLHEAD_STANDBY TOOLHEAD={0 if initial_tool == 1 else 1}
	{% else %}
	_LED_PRINTING TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% else %}
	_LED_PRINTING TOOLHEAD={initial_tool}
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={0 if initial_tool == 1 else 1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_USER_START_PRINT_AFTER_HEATING_EXTRUDER { rawparams } X0={X0} X1={X1} Y0={Y0} Y1={Y1}
	
	
	_START_PRINT_AFTER_HEATING_EXTRUDER X0={X0} X1={X1} Y0={Y0} Y1={Y1} INITIAL_TOOLHEAD={initial_tool} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode}
	
	
	{% if idex_mode != '' %}
	{% if not both_toolheads %}
	{% if initial_tool != default_toolhead %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% if idex_mode != '' %}
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=standby VALUE=False
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=standby VALUE=False
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if initial_tool == 1 else 'extruder1'} TARGET={toolchange_standby_temp}
	SET_GCODE_VARIABLE MACRO=T{0 if initial_tool == 1 else 1} VARIABLE=standby VALUE=True
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=start_print_state
	
	{% if printer["dual_carriage"] is defined %}
	_SET_IDEX_MODE_OFFSET
	{% endif %}
	
	
	{% if idex_mode != '' %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% if idex_mode == "copy" and idex_mode != act_idex_mode %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == "mirror" and idex_mode != act_idex_mode %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={object_xoffset} MOVE=0
	{% endif %}
	{% else %}
	_SELECT_TOOL T={initial_tool} TOOLSHIFT=false
	_SET_TOOLHEAD_OFFSET
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	_SET_EXTRUSION_MODE
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=True
	
	
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={printer["print_stats"].print_duration}
	{% endif %}
	
	
	_USER_END_START_PRINT { rawparams }
	
	G92 E0
	
	
	_CHAMBER_FILTER_ON AT="after_print_start"
	
	_ALERT_NON_ZERO_Z_OFFSET
	
	RATOS_ECHO MSG="Printing..."

[gcode_macro _START_PRINT_BEFORE_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set is_stowable_probe = true if printer["gcode_macro RatOS"].z_probe|lower == 'stowable' else false %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Pre-heating extruder..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={min_temp}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET={min_temp}
	{% endif %}
	{% else %}
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={min_temp}
	{% endif %}
	{% endif %}
	
	
	{% if not is_stowable_probe %}
	{% if printer["dual_carriage"] is defined and act_t != default_toolhead %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	{% endif %}
	RATOS_ECHO MSG="Heat soaking z probe..."
	_MOVE_TO_SAFE_Z_HOME
	
	G0 Z2 F{z_speed}
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED]
gcode = 
	
	{% set target_idex_mode = params.IDEX_MODE|default("")|lower %}
	{% set initial_toolhead = params.T|default(default_toolhead)|int %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	
	
	{% set min_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float %}
	{% set max_temp = printer["gcode_macro RatOS"].preheat_extruder_temp|float + 5 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	
	
	{% set auto_z_offset_calibration = False %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro _VAOC"] is defined %}
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% if printer["gcode_macro _VAOC"].auto_z_offset_calibration|default("false")|lower == 'true' and is_fixed %}
	{% if target_idex_mode != "copy" and target_idex_mode != "mirror" %}
	{% if both_toolheads or initial_toolhead != default_toolhead %}
	{% set auto_z_offset_calibration = True %}
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	
	
	{% if printer["gcode_macro RatOS"].preheat_extruder|lower == 'true' %}
	RATOS_ECHO MSG="Waiting for extruder to be preheated..."
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if auto_z_offset_calibration %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	{% if default_toolhead == 0 %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder1 MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	{% else %}
	TEMPERATURE_WAIT SENSOR=extruder MINIMUM={min_temp} MAXIMUM={max_temp}
	{% endif %}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined %}
	_Z_HOP
	{% endif %}
	
	
	{% if auto_z_offset_calibration %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=True
	PARK_TOOLHEAD
	_CLEANING_MOVE TOOLHEAD={default_toolhead} AUTOMATED=True
	_SELECT_TOOL T={0 if default_toolhead == 1 else 1} X={parking_position_t0 if default_toolhead == 1 else parking_position_t1} Y=0 TOOLSHIFT=false
	_CLEANING_MOVE TOOLHEAD={0 if default_toolhead == 1 else 1} AUTOMATED=True
	_VAOC_CALIBRATE_Z_OFFSET AUTO_Z_OFFSET=True
	_SELECT_TOOL T={default_toolhead} X={safe_home_x} Y={safe_home_y} TOOLSHIFT=false
	{% endif %}
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	{% if needs_rehoming %}
	G28 Z
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	_START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE
	{% endif %}
	{% endif %}
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE
	{% endif %}

[gcode_macro _START_PRINT_AFTER_HEATING_BED_PROBE_FOR_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	PROBE PROBE_METHOD=contact SAMPLES=1

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE]
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_wipe_before_true_zero_method = printer["gcode_macro RatOS"].beacon_contact_wipe_before_true_zero_method|default("probe_clean")|lower %}
	{% set beacon_contact_calibrate_model_on_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero_fuzzy_position = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_position|default(false)|lower == 'true' else false %}
	{% set fuzzy_radius = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero_fuzzy_radius|default(0)|float if beacon_contact_start_print_true_zero_fuzzy_position else 0 %}
	
	{% set contact_true_zero_temp_has_been_set = False %}
	
	
	{% if beacon_contact_wipe_before_true_zero %}
	{% if beacon_contact_wipe_before_true_zero_method == "wipe" %}
	
	
	
	{% if printer.beacon.last_probe_result|lower == "ok" %}
	{% set last_z_offset = printer.beacon.last_z_result %}
	RATOS_ECHO MSG="Auto calibration nozzle wipe with probe result {last_z_offset}..."
	G0 Z{(0.2 + last_z_offset)} F{z_speed}
	G0 X70 F300
	{% else %}
	RATOS_ECHO MSG="Skipping auto calibration nozzle wipe because probing failed!"
	{% endif %}
	{% elif beacon_contact_wipe_before_true_zero_method == "probe_clean" %}
	
	G0 Z5 F{z_speed}
	G0 X50 Y10 F{speed}
	
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	
	{% set contact_true_zero_temp_has_been_set = True %}
	
	
	
	
	
	
	
	
	BEACON_PROBE_CLEAN X=50 Y=10
	{% else %}
	CONSOLE_ECHO TYPE="error" TITLE="Unknown wipe method" MSG="Unknown wipe method '{beacon_contact_wipe_before_true_zero_method}' configured, skipping wipe before beacon true zero."
	{% endif %}
	{% endif %}
	
	
	G0 Z5 F{z_speed}
	_MOVE_TO_SAFE_Z_HOME FUZZY_RADIUS={fuzzy_radius}
	
	
	_START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION
	
	{% if not contact_true_zero_temp_has_been_set %}
	
	RATOS_ECHO MSG="Heating extruder to probing temperature..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={beacon_contact_true_zero_temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={beacon_contact_true_zero_temp} MAXIMUM={beacon_contact_true_zero_temp + 5}
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon contact auto calibration..."
	
	{% if beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1
	{% endif %}
	
	G0 Z5 F{z_speed}

[gcode_macro _START_PRINT_AFTER_HEATING_CONTACT_WITH_OPTIONAL_WIPE_STORE_TRUE_ZERO_POSITION]
gcode = 
	{% set pos = printer.ratos.last_move_to_safe_z_home_position %}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_x VALUE={pos[0]}
	SET_GCODE_VARIABLE MACRO=_START_PRINT_BED_MESH VARIABLE=actual_true_zero_position_y VALUE={pos[1]}

[gcode_macro _START_PRINT_AFTER_HEATING_EXTRUDER]
gcode = 
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set first_x = printer["gcode_macro START_PRINT"].first_x|default(-1)|float %}
	{% set first_y = printer["gcode_macro START_PRINT"].first_y|default(-1)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2.0 %}
	{% set center_y = printable_y_max / 2.0 %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% if printer["dual_carriage"] is defined %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% endif %}
	
	
	{% set X0 = params.X0|default(-1)|int %}
	{% set X1 = params.X1|default(-1)|int %}
	{% set Y0 = params.Y0|default(-1)|int %}
	{% set Y1 = params.Y1|default(-1)|int %}
	{% set idex_mode = params.IDEX_MODE|default('')|lower %}
	{% set both_toolheads = true if params.BOTH_TOOLHEADS|default(true)|lower=='true' else false %}
	{% set initial_toolhead = params.INITIAL_TOOLHEAD|default(default_toolhead)|int %}
	
	{% if idex_mode == '' %}
	
	_PRIME
	{% else %}
	
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	RATOS_ECHO PREFIX="IDEX" MSG="using combined prime offset for IDEX {idex_mode} mode"
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	{% if both_toolheads %}
	{% if initial_toolhead == 0 %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T0"
	_SELECT_TOOL T=0 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T1"
	_SELECT_TOOL T=1 TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% else %}
	RATOS_ECHO PREFIX="IDEX" MSG="using prime offset for T{initial_toolhead}"
	_SELECT_TOOL T={initial_toolhead} TOOLSHIFT=false
	_PRIME INITIAL_TOOLHEAD={initial_toolhead} BOTH_TOOLHEADS={both_toolheads} IDEX_MODE={idex_mode} Y1={Y1}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	CACHE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	SET_MACRO_TRAVEL_SETTINGS
	
	{% if (X0 > -1 and Y1 > -1) or (first_x > 0 and first_y > 0) %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	{% endif %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	G0 Z3 F{z_speed}
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	{% set first_z = 1 %}
	{% else %}
	{% set first_z = 3 %}
	{% endif %}
	
	
	{% if idex_mode == "mirror" %}
	{% if first_y >= 0 %}
	G0 Y{first_y} F{speed}
	{% else %}
	G0 Y{Y1} F{speed}
	{% endif %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if printer["dual_carriage"] is defined and printer["gcode_macro RatOS"].nozzle_priming|lower == 'false' %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={initial_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={initial_toolhead} E={printer["gcode_macro RatOS"].toolchange_first_purge|default(50)|float}
	_CLEANING_MOVE TOOLHEAD={initial_toolhead} AUTOMATED=True
	{% endif %}
	{% if first_x >= 0 and first_y >= 0 %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% else %}
	{% set first_x = X0 %}
	{% set first_y = Y0 %}
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'min' %}
	{% set first_x = X0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_x|lower == 'max' %}
	{% set first_x = X1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_x|float <= center_x %}
	{% set first_x = X0 %}
	{% else %}
	{% set first_x = X1 %}
	{% endif %}
	{% endif %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'min' %}
	{% set first_y = Y0 %}
	{% elif printer["gcode_macro RatOS"].nozzle_prime_start_y|lower == 'max' %}
	{% set first_y = Y1 %}
	{% else %}
	{% if printer["gcode_macro RatOS"].nozzle_prime_start_y|float <= center_y %}
	{% set first_y = Y0 %}
	{% else %}
	{% set first_y = Y1 %}
	{% endif %}
	{% endif %}
	{% endif %}
	G0 X{first_x} Y{first_y} Z{first_z} F{speed}
	{% endif %}
	{% endif %}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print_after_heating_extruder"
	
	
	_LOAD_RATOS_SKEW_PROFILE

[gcode_macro _PRIME]
gcode = 
	
	{% if printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeblob' or printer["gcode_macro RatOS"].nozzle_priming|lower == 'primeline' %}
	PRIME_BLOB INITIAL_TOOLHEAD={params.INITIAL_TOOLHEAD} BOTH_TOOLHEADS={params.BOTH_TOOLHEADS} IDEX_MODE={params.IDEX_MODE} Y1={params.Y1}
	{% else %}
	
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if params.IDEX_MODE == "copy" %}
	_IDEX_COPY DANCE=0
	{% elif params.IDEX_MODE == "mirror" %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro END_PRINT]
description = End print procedure, use this in your Slicer.
gcode = 
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SAVE_GCODE_STATE NAME=end_print_state
	{% if printer["dual_carriage"] is defined %}
	
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	
	{% if printer["gcode_macro RatOS"].auto_center_subject|default(false)|lower == 'true' %}
	{% set object_xoffset = printer["gcode_macro START_PRINT"].object_xoffset|default(0)|float %}
	RATOS_ECHO MSG="Adjusting object x-offset by {(0-object_xoffset)} mm"
	SET_GCODE_OFFSET X_ADJUST={(0-object_xoffset)}
	{% endif %}
	{% endif %}
	
	
	_USER_END_PRINT_BEFORE_HEATERS_OFF { rawparams }
	_END_PRINT_BEFORE_HEATERS_OFF
	TURN_OFF_HEATERS
	_USER_END_PRINT_AFTER_HEATERS_OFF { rawparams }
	_END_PRINT_AFTER_HEATERS_OFF
	_USER_END_PRINT_PARK { rawparams }
	_END_PRINT_PARK
	
	
	{% if printer["gcode_macro RatOS"].skew_profile is defined %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	{% if printer["dual_carriage"] is not defined and printer["gcode_macro RatOS"].end_print_motors_off|lower != 'false' %}
	
	M84
	{% endif %}
	
	
	M107
	
	
	BED_MESH_CLEAR
	RATOS_ECHO MSG="Done :)"
	
	
	RESTORE_GCODE_STATE NAME=end_print_state
	
	
	{% if printer["dual_carriage"] is defined %}
	
	
	M84
	{% endif %}
	
	
	RESET_NAMED_OFFSET EVENT="end_print"
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="start_print"
	
	
	_CHAMBER_FILTER_ON AT="print_end"
	_CHAMBER_FILTER_OFF
	
	
	_CHAMBER_HEATER_OFF
	
	_USER_END_PRINT_FINISHED { rawparams }

[gcode_macro _END_PRINT_BEFORE_HEATERS_OFF]
gcode = 
	RATOS_ECHO MSG="Cleaning up..."

[gcode_macro _END_PRINT_AFTER_HEATERS_OFF]
gcode = 
	
	{% set idex_mode = '' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set idex_toolhead = 1 if idex_mode == 'primary' else 0 %}
	{% endif %}
	
	
	{% set max_z = printer.toolhead.axis_maximum.z|float %}
	{% set current_z = printer.toolhead.position.z|float %}
	{% set z_hop = printer["gcode_macro RatOS"].end_print_park_z_hop|float %}
	{% set r = printer["gcode_macro RatOS"].end_print_retract_filament|default(4)|float %}
	{% if current_z < (max_z - z_hop) %}
	{% set z_safe = z_hop %}
	{% else %}
	{% set z_safe = max_z - current_z %}
	{% endif %}
	
	
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' else false %}
	{% if idex_mode != '' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% set can_extrude = true if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% else %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% set can_extrude = true if printer['extruder1'].can_extrude|lower == 'true' else false %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	G91
	
	{% if can_extrude %}
	G1 E-2 F3600
	{% endif %}
	
	G0 Z{z_safe} F3600
	
	{% if can_extrude %}
	G1 E-{(r-2)} F3600
	{% endif %}
	
	G90

[gcode_macro _SET_EXTRUSION_MODE]
gcode = 
	
	{% if printer["gcode_macro RatOS"].relative_extrusion|lower == 'true' %}
	M83
	{% else %}
	M82
	{% endif %}

[gcode_macro GENERATE_SHAPER_GRAPHS]
description = Genarates input shaper resonances graphs for analysis. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	{% set hz_per_sec = params.HZ_PER_SEC|default(1)|float %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set copy_mode_offset = printable_x_max / 4.0 %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% else %}
	_IDEX_SINGLE
	{% endif %}
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' %}
	{% if idex_mode == 'copy' %}
	_IDEX_COPY DANCE=0
	{% elif idex_mode == 'mirror' %}
	_IDEX_MIRROR DANCE=0
	{% endif %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if idex_mode == 'copy' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_copy FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 1 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% elif idex_mode == 'mirror' %}
	{% if measure_t0 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1_mirror FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0] - copy_mode_offset},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% if measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 2 %s %s %s" % ('%0.3f'|format(probe_points[0] - copy_mode_offset), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	{% else %}
	G1 X{probe_points[0]} Y{probe_points[1]} F{speed}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[0]}" NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]}" NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} HZ_PER_SEC={hz_per_sec} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t0 == true and measure_t1 == false %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 0 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == false and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 1 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% elif measure_t0 == true and measure_t1 == true %}
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"x 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	RUN_SHELL_COMMAND CMD=generate_shaper_graphs PARAMS="{"y 2 0 %s %s %s" % ('%0.3f'|format(probe_points[0]), '%0.3f'|format(probe_points[1]), '%0.3f'|format(probe_points[2]))}"
	{% endif %}
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="generate_shaper_graphs"
	
	
	{% if idex_mode != 'copy' and idex_mode != 'mirror' %}
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	{% endif %}
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Shaper graph"

[gcode_shell_command generate_shaper_graph_x]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-x.sh
timeout = 60.
verbose = True

[gcode_shell_command generate_shaper_graph_y]
command = /home/pi/printer_data/config/RatOS/scripts/generate-shaper-graph-y.sh
timeout = 60.
verbose = True

[gcode_macro MEASURE_COREXY_BELT_TENSION]
description = Generates resonance graph used to ensure belts are equally tensioned. Uses the AXIS, TOOLHEAD, FREQUNECY_START and FREQUENCY_END parameter if you want to do specific measurements, (eg. GENERATE_SHAPER_GRAPHS AXIS=X TOOLHEAD=0 FREQUENCY_START=10 FREQUENCY_END=20)
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	CACHE_IS_GRAPH_FILES
	
	
	{% set measure_t0 = true %}
	{% set measure_t1 = true %}
	{% if params.TOOLHEAD is defined %}
	{% if params.TOOLHEAD|lower == '0' %}
	{% set measure_t1 = false %}
	{% elif params.TOOLHEAD|lower == '1' %}
	{% set measure_t0 = false %}
	{% else %}
	{action_raise_error("Unknown toolhead specified. Expected 0 or 1 (left or right)")}
	{% endif %}
	{% endif %}
	{% set axis = params.AXIS|default('')|lower %}
	{% set freq_start = params.FREQUENCY_START|default(10)|int %}
	{% set freq_end = params.FREQUENCY_END|default(133)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set adxl_chip = printer["gcode_macro RatOS"].adxl_chip %}
	{% set probe_points = printer.fastconfig.settings.resonance_tester.probe_points[0] %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set default_toolhead_parking_position = printer["gcode_macro T%s" % default_toolhead].parking_position|float %}
	
	
	MAYBE_HOME
	_IDEX_SINGLE
	G90
	
	
	_LED_INPUT_SHAPER_START
	
	{% if axis != '' %}
	{% if axis == 'x' %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	PARK_TOOLHEAD
	{% elif axis == 'y' %}
	{% if measure_t1 == false or measure_t0 == false %}
	{action_raise_error("Axis specified. Not supported for belt tension on Y.")}
	{% else %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	G4 P5000
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	PARK_TOOLHEAD
	{% endif %}
	{% else %}
	{action_raise_error("Unknown axis specified. Expected X or Y.")}
	{% endif %}
	{% else %}
	{% if measure_t1 == true %}
	_SELECT_TOOL T=1 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[1]}" OUTPUT=raw_data NAME=t1 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if measure_t0 == true %}
	_SELECT_TOOL T=0 X={probe_points[0]} Y={probe_points[1]}
	TEST_RESONANCES AXIS=X CHIPS="{adxl_chip[0]}" OUTPUT=raw_data NAME=t0 FREQ_START={freq_start} FREQ_END={freq_end} POINT={probe_points[0]},{probe_points[1]},{probe_points[2]}
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	_SELECT_TOOL T=1 X={parking_position_t1} Y={probe_points[1]}
	G1 X{parking_position_t1} F{speed}
	TEST_RESONANCES AXIS=Y CHIPS="{adxl_chip[1]},{adxl_chip[0]}" OUTPUT=raw_data NAME=t2 POINT={parking_position_t1},{probe_points[1]},{probe_points[2]} FREQ_START={freq_start} FREQ_END={freq_end}
	{% endif %}
	G4 P5000
	{% if measure_t1 == true and measure_t0 == false %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 1"
	{% elif measure_t1 == false and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="x 0"
	{% elif measure_t1 == true and measure_t0 == true %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS=x
	{% endif %}
	{% if params.TOOLHEAD is not defined %}
	RUN_SHELL_COMMAND CMD=generate_tension_graphs PARAMS="y 2"
	{% endif %}
	PARK_TOOLHEAD
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="measure_corexy_belt_tension"
	
	
	_IDEX_SINGLE X={default_toolhead_parking_position} INIT=1
	
	
	_LED_INPUT_SHAPER_END
	
	
	_LEARN_MORE_CALIBRATION
	
	
	SHOW_IS_GRAPH_FILES TITLE="Belt Tension Graph"

[gcode_shell_command generate_belt_tension_graph]
command = /home/pi/printer_data/config/RatOS/scripts/generate-belt-tension-graph.sh
timeout = 90.
verbose = True

[idle_timeout]
gcode = 
	{% if printer.webhooks.state|lower == 'ready' %}
	{% if printer.pause_resume.is_paused|lower == 'false' %}
	_USER_BEFORE_IDLE_TIMEOUT
	RATOS_ECHO PREFIX="IDLE" MSG="2 hours since last activity. Powering off heaters and motors.."
	TURN_OFF_HEATERS
	M84
	_USER_AFTER_IDLE_TIMEOUT
	{% endif %}
	{% endif %}
timeout = 7200

[temperature_sensor raspberry_pi]
sensor_type = temperature_host

[skew_correction]

[named_offsets]

[input_shaper]

[virtual_sdcard]
path = ~/printer_data/gcodes

[display_status]

[pause_resume]

[force_move]
enable_force_move = True

[respond]

[resonance_generator]

[ratos]
allow_unknown_gcode_generator = True
enable_gcode_transform = True

[exclude_object]

[bed_mesh]
split_delta_z = 0.001
horizontal_move_z = 2
mesh_min = 20,20
mesh_max = 480,480
probe_count = 40,40
mesh_pps = 2,2
algorithm = bicubic
bicubic_tension = .2
speed = 600
log_points = False

[fastconfig]

[heater_bed]
heater_pin = heater_bed_heating_pin
sensor_pin = heater_bed_sensor_pin
sensor_type = Generic 3950
min_temp = 0
max_temp = 140
pwm_cycle_time = 0.103
control = pid
pid_kp = 61.987
pid_ki = 1.781
pid_kd = 539.289

[printer]
kinematics = ratos_hybrid_corexy
max_velocity = 800
max_accel = 10000
minimum_cruise_ratio = 0.5
max_z_velocity = 50
max_z_accel = 600
square_corner_velocity = 5

[ratos_hybrid_corexy]
inverted = true

[dual_carriage]
axis = x
safe_distance = 55
position_max = 559.6
position_endstop = 559.6
position_min = 0
step_pin = PF9
dir_pin = dual_carriage_dir_pin
enable_pin = !PG2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t1:PA2

[gcode_macro _SET_IDEX_MODE_OFFSET]
description = "Internal use only. Sets the 'idex_mode' named offset that the active idex mode requires."
gcode = 
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_SET_IDEX_MODE_OFFSET" MSG="idex_mode: {idex_mode}, center_x: {center_x}"
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	SET_NAMED_OFFSET NAME=idex_mode X={(-center_x / 2)}
	{% else %}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% else %}
	{action_raise_error("_SET_IDEX_MODE_OFFSET: Printer not homed")}
	{% endif %}

[gcode_macro IDEX_SINGLE]
gcode = 
	_IDEX_REMAP_TOOLHEADS ENABLE=False
	_IDEX_SINGLE

[gcode_macro _IDEX_SINGLE]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_single"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set init = params.INIT|default(0)|int %}
	{% set new_x = params.X|default(-1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_default_t = printer["gcode_macro T%s" % (0 if default_toolhead==1 else 1)].parking_position|float %}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="init: {init}, new_x: {new_x}, idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, act_t: {act_t}"
	
	{% if idex_mode == "copy" or idex_mode == "mirror" or init == 1 %}
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="reset idex_mode offset"
	G1 X{center_x} F{(speed)}
	SET_NAMED_OFFSET NAME=idex_mode X=0
	{% endif %}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="activate default carriage"
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead} MODE=PRIMARY
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolheads"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	G90
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position."
	SET_DUAL_CARRIAGE CARRIAGE={0 if default_toolhead==1 else 1}
	G1 X{parking_position_default_t} F{speed}
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move default toolhead to its new position."
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% if new_x == -1 %}
	{% set new_x = center_x %}
	{% endif %}
	G1 X{new_x} F{speed}
	
	M400
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="X Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set extruder motion queue."
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if default_toolhead==0 else default_toolhead}
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set toolhead offset."
	_SET_TOOLHEAD_OFFSET
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="set input shaper."
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[default_toolhead]|float)} SHAPER_FREQ_Y={(shaper_y_freq[default_toolhead]|float)} SHAPER_TYPE_X={(shaper_x_type[default_toolhead]|lower)} SHAPER_TYPE_Y={(shaper_y_type[default_toolhead]|lower)}
	
	
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="update Frontend."
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if default_toolhead==0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if default_toolhead==1 else False}
	{% else %}
	{% if "xyz" in printer.toolhead.homed_axes %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="move secondary toolhead to parking position"
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	{% else %}
	DEBUG_ECHO PREFIX="IDEX_SINGLE" MSG="Axis not homed."
	
	SET_DUAL_CARRIAGE CARRIAGE={default_toolhead}
	{% endif %}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_single"

[gcode_macro IDEX_COPY]
gcode = 
	_IDEX_COPY

[gcode_macro _IDEX_COPY]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_copy"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set y = params.Y|default(-1)|int %}
	{% set dance = params.DANCE|default(1)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_COPY" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}, y: {y}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "copy" %}
	{% if idex_mode == "mirror" %}
	{% if y>=0 %}
	G1 X{center_x} Y{y} F{(speed)}
	{% else %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	
	
	{% if idex_mode != "mirror" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance == 1 %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[2]|float)} SHAPER_FREQ_Y={(shaper_y_freq[2]|float)} SHAPER_TYPE_X={(shaper_x_type[2]|lower)} SHAPER_TYPE_Y={(shaper_y_type[2]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_copy"

[gcode_macro IDEX_MIRROR]
gcode = 
	_IDEX_MIRROR

[gcode_macro _IDEX_MIRROR]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_mirror"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set dance = params.DANCE|default(1)|int %}
	{% set priming = params.PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="IDEX_MIRROR" MSG="idex_mode: {idex_mode}, printable_x_max: {printable_x_max}, center_x: {center_x}, dance: {dance}"
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	{% if idex_mode != "mirror" %}
	
	{% if idex_mode == "copy" %}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	{% if idex_mode == "primary" or idex_mode == "inactive" %}
	_IDEX_SET_TOOLHEADS MIRROR_PRIMING={params.PRIMING}
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER='extruder'
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=MIRROR
	
	
	{% if idex_mode != "copy" %}
	SET_PRESSURE_ADVANCE
	{% endif %}
	
	
	_SET_IDEX_MODE_OFFSET
	_SET_TOOLHEAD_OFFSET
	
	
	{% if dance and not priming %}
	G1 X{center_x} F{(speed)}
	G1 X{center_x - 30} F{(speed)}
	G1 X{center_x + 30} F{(speed)}
	G1 X{center_x} F{(speed)}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[3]|float)} SHAPER_FREQ_Y={(shaper_y_freq[3]|float)} SHAPER_TYPE_X={(shaper_x_type[3]|lower)} SHAPER_TYPE_Y={(shaper_y_type[3]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE=True
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE=True
	
	{% endif %}
	{% else %}
	{action_respond_info("Printer not homed")}
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_mirror"

[gcode_macro _IDEX_SET_TOOLHEADS]
gcode = 
	
	CACHE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"
	SET_MACRO_TRAVEL_SETTINGS
	
	
	{% set mirror_priming = params.MIRROR_PRIMING|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set parking_position_inactive_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_x = printable_x_max / 2 %}
	
	DEBUG_ECHO PREFIX="_IDEX_SET_TOOLHEADS" MSG="idex_mode: {idex_mode}, act_t: {act_t}, center_x: {center_x}, mirror_priming: {mirror_priming}"
	
	
	{% if act_t != default_toolhead %}
	_SET_TOOLHEAD_OFFSET FORCE_TOOLHEAD={default_toolhead} MOVE=1
	{% endif %}
	
	{% if mirror_priming %}
	
	
	
	{% if parking_position_t0|abs < parking_position_t1 - printable_x_max %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{printable_x_max + parking_position_t0|abs} F{(speed)}
	{% else %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{0 - (parking_position_t1 - printable_x_max)} F{(speed)}
	{% endif %}
	
	{% else %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1} MODE=PRIMARY
	G1 X{parking_position_inactive_t} F{(speed)}
	
	
	{% if act_t==1 %}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{center_x / 2} F{(speed)}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{center_x / 2 + center_x} F{(speed)}
	
	{% endif %}
	
	
	RESTORE_TOOLHEAD_SETTINGS KEY="idex_set_toolheads"

[gcode_macro IDEX_PARK]
gcode = 
	
	PARK_TOOLHEAD

[gcode_macro PARK_TOOLHEAD]
gcode = 
	
	{% set idex_mode = 'none' %}
	{% if printer["dual_carriage"] is defined %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% endif %}
	{% set act_t = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="PARK_TOOLHEAD" MSG="Parking T{act_t}.."
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set parking_position_inact_t = printer["gcode_macro T%s" % (0 if act_t==1 else 1)].parking_position|float %}
	{% set printable_y_min = printer["gcode_macro RatOS"].printable_y_min|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% if idex_mode != "copy" and idex_mode != "mirror" and 'xy' in printer.toolhead.homed_axes %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% elif printer.toolhead.position.y|float < printable_y_min %}
	G1 Y{printable_y_min} F{speed}
	{% endif %}
	
	SAVE_GCODE_STATE NAME=_PARK_TOOLHEAD
	G90
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0.5
	
	
	G1 X{parking_position_act_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={0 if act_t==1 else 1}
	G1 X{parking_position_inact_t} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE={act_t}
	
	SET_VELOCITY_LIMIT ACCEL={printer.toolhead.max_accel} MINIMUM_CRUISE_RATIO=0.5
	M400
	RESTORE_GCODE_STATE NAME=_PARK_TOOLHEAD
	
	{% endif %}

[gcode_macro JOIN_SPOOLS]
gcode = 
	
	{% set spools = params.SPOOLS|default("") %}
	
	{% if spools == "" %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% else %}
	{% if spools != "0,1" and spools != "1,0" %}
	RATOS_ECHO MSG="Wrong spool configuration!"
	RATOS_ECHO MSG="Join Spools = JOIN_SPOOLS SPOOLS=0,1"
	RATOS_ECHO MSG="Deactivate = JOIN_SPOOLS SPOOLS="
	{% else %}
	{% if spools == "0,1" or spools == "1,0" %}
	_IDEX_JOIN_SPOOLS ENABLE=true
	{% else %}
	_IDEX_JOIN_SPOOLS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_JOIN_SPOOLS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=False
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% if enable %}
	{% set has_t0_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t1_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined else false %}
	{% set has_t0_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined else false %}
	{% set has_t1_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined else false %}
	{% if (has_t0_toolhead_filament_sensor and has_t1_toolhead_filament_sensor) or (has_t0_bowden_filament_sensor and has_t1_bowden_filament_sensor) %}
	SET_GCODE_VARIABLE MACRO=_IDEX_JOIN_SPOOLS VARIABLE=enabled VALUE=True
	RATOS_ECHO MSG="Spool joining enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Can not enable spool joining! No filament sensors found."
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining deactivated!"
	{% endif %}
	{% else %}
	RATOS_ECHO MSG="Spool joining is not possible in copy and mirror mode!"
	{% endif %}

[gcode_macro _JOIN_SPOOL]
gcode = 
	
	{% set old_toolhead = params.TOOLHEAD|int %}
	{% set new_toolhead = 0 if old_toolhead == 1 else 1 %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed|float * 60 %}
	{% set purge_after_load = printer["gcode_macro T%s" % new_toolhead].purge_after_load|float %}
	
	DEBUG_ECHO PREFIX="_JOIN_SPOOL" MSG="toolhead: {new_toolhead}"
	
	{% set has_filament = true %}
	{% set has_new_toolhead_filament_sensor = true if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% set has_new_bowden_filament_sensor = true if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead] is defined else false %}
	{% if has_new_toolhead_filament_sensor %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	{% if has_new_bowden_filament_sensor %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].enabled|lower == "true" %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t%s" % new_toolhead].filament_detected|lower != "true" %}
	{% set has_filament = false %}
	{% endif %}
	{% else %}
	{% set has_filament = false %}
	{% endif %}
	{% endif %}
	
	{% if has_filament %}
	RATOS_ECHO MSG="Joining spools! Please wait for extruder to heat up...."
	
	
	SET_GCODE_VARIABLE MACRO=PAUSE VARIABLE=idex_toolhead VALUE={new_toolhead}
	
	
	_DEACTIVATE_TOOLHEAD TOOLHEAD={old_toolhead}
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set extruder_temp = extruder_first_layer_temp[new_toolhead]|float %}
	{% else %}
	{% set extruder_temp = extruder_other_layer_temp[new_toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if new_toolhead == 0 else 'extruder1'} TARGET={extruder_temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if new_toolhead == 0 else 'extruder1'} MINIMUM={extruder_temp}  MAXIMUM={extruder_temp + 5}
	
	
	{% if purge_after_load > 0 %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_toolhead == 0 else new_toolhead}
	
	
	_MOVE_TO_LOADING_POSITION TOOLHEAD={new_toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={new_toolhead} E={purge_after_load}
	_CLEANING_MOVE TOOLHEAD={new_toolhead} AUTOMATED=True
	
	
	SET_DUAL_CARRIAGE CARRIAGE={old_toolhead} MODE=PRIMARY
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if old_toolhead == 0 else old_toolhead}
	
	{% endif %}
	
	
	RESUME TOOLHEAD={new_toolhead}
	
	
	_IDEX_JOIN_SPOOLS ENABLE=false
	
	{% else %}
	{ action_raise_error("Spool join failed! No filament found or filament sensor is disabled.") }
	{% endif %}

[gcode_macro REMAP_TOOLHEADS]
gcode = 
	
	{% set toolheads = params.TOOLHEADS|default("") %}
	
	{% if toolheads == "" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% else %}
	{% if toolheads != "0,1" and toolheads != "1,0" %}
	RATOS_ECHO MSG="Wrong toolhead configuration!"
	RATOS_ECHO MSG="Remap = REMAP_TOOLHEADS TOOLHEADS=0,1"
	RATOS_ECHO MSG="Deactivate = REMAP_TOOLHEADS TOOLHEADS="
	{% else %}
	{% if toolheads == "0,1" or toolheads == "1,0" %}
	_IDEX_REMAP_TOOLHEADS ENABLE=true
	_IDEX_SINGLE
	{% else %}
	_IDEX_REMAP_TOOLHEADS ENABLE=false
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _IDEX_REMAP_TOOLHEADS]
variable_enabled = False
gcode = 
	
	{% set enable = true if params.ENABLE|default(false)|lower == 'true' else false %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	
	{% if not enable or (idex_mode != "copy" and idex_mode != "mirror") %}
	{% if enable %}
	RATOS_ECHO MSG="Toolhead remapping enabled for the next print!"
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping deactivated!"
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE={enable}
	{% else %}
	RATOS_ECHO MSG="Toolhead remapping not possible in copy and mirror mode!"
	SET_GCODE_VARIABLE MACRO=_IDEX_REMAP_TOOLHEADS VARIABLE=enabled VALUE=False
	{% endif %}

[gcode_macro SHAPER_CALIBRATE]
rename_existing = SHAPER_CALIBRATE_ORG
gcode = 
	RATOS_ECHO PREFIX="IDEX" MSG="SHAPER_CALIBRATE is useless on IDEX machines. Please use the GENERATE_SHAPER_GRAPHS macro and type the values into `variable_shaper_*_freq` and `variable_shaper_*_type manually`."

[gcode_shell_command generate_shaper_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-shaper-graph.sh
timeout = 120.
verbose = True

[gcode_shell_command generate_tension_graphs]
command = /home/pi/printer_data/config/RatOS/scripts/idex-generate-belt-tension-graph.sh
timeout = 120.
verbose = True

[gcode_macro SET_PRESSURE_ADVANCE]
variable_snyc_toolheads = False
rename_existing = SET_PRESSURE_ADVANCE_BASE
gcode = 
	{% if params.SYNC_TOOLHEADS is defined %}
	{% set snyc_toolheads = true if params.SYNC_TOOLHEADS|default(false)|lower == 'true' else false %}
	SET_GCODE_VARIABLE MACRO=SET_PRESSURE_ADVANCE VARIABLE=snyc_toolheads VALUE=True
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="Syncing toolheads..."
	{% else %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% if idex_mode == 'copy' or idex_mode == 'mirror' or snyc_toolheads %}
	{% set advance = params.ADVANCE|default(printer['extruder'].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['extruder'].smooth_time|float)|float %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T0"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG="T1"
	SET_PRESSURE_ADVANCE_BASE EXTRUDER='extruder1' ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% else %}
	{% set extruder = 'extruder' if act_t == 0 else 'extruder1' %}
	{% if params.EXTRUDER is defined %}
	{% set extruder = params.EXTRUDER %}
	{% endif %}
	{% if extruder == 'extruder' or extruder == 'extruder1' %}
	{% set advance = params.ADVANCE|default(printer['%s' % extruder].pressure_advance|float)|float %}
	{% set smooth_time = params.SMOOTH_TIME|default(printer['%s' % extruder].smooth_time|float)|float %}
	SET_PRESSURE_ADVANCE_BASE EXTRUDER={extruder} ADVANCE={advance} SMOOTH_TIME={smooth_time}
	{% if params.EXTRUDER is not defined %}
	RATOS_ECHO PREFIX="SET_PRESSURE_ADVANCE" MSG={"T%s" % act_t}
	{% endif %}
	{% else %}
	SET_PRESSURE_ADVANCE_BASE { rawparams }
	{% endif %}
	{% endif %}
	
	{% endif %}

[gcode_macro M106]
rename_existing = M106.1
variable_swap_speed = -1
gcode = 
	
	{% set s = [[params.S|default(255)|int, 255]|min, 0]|max %}
	{% set p = params.P|default(-1)|int %}
	{% set speed = s / 255 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|default('')|lower %}
	{% set t = 1 if idex_mode=='primary' else 0 %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(0)|int == 1 else false %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	{% set sync_fans = true %}
	{% endif %}
	
	
	{% if sync_fans and idex_mode != "copy" and idex_mode != "mirror" %}
	
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int %}
	
	
	{% if toolshift_count > total_toolshifts %}
	{% set sync_fans = false %}
	{% endif %}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE=-1
	
	
	{% if p == -1 %}
	
	{% if speed == 0 %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed}
	{% else %}
	
	SET_GCODE_VARIABLE MACRO=M106 VARIABLE=swap_speed VALUE={speed}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={(speed if (t == 0 or sync_fans) else 0)}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={(speed if (t == 1 or sync_fans) else 0)}
	{% endif %}
	{% else %}
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={speed if t == p else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={speed if t == p else 0}
	{% endif %}
	
	
	M106.1 S{s}

[gcode_macro M107]
rename_existing = M107.1
gcode = 
	{% set p = params.P|default(-1)|int %}
	M106 S0 P{p}

[gcode_macro _SELECT_TOOL]
variable_last_timestamp = 0
gcode = 
	{% if params.T is defined %}
	{% set idex_mode = '' %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if "xyz" not in printer.toolhead.homed_axes and (idex_mode == "copy" or idex_mode == "mirror") %}
	_IDEX_SINGLE
	{% set idex_mode = 'reset' %}
	{% endif %}
	{% if idex_mode != "copy" and idex_mode != "mirror" %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set new_t = params.T|int %}
	
	
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	{% set swap_toolheads = true if printer["gcode_macro _IDEX_REMAP_TOOLHEADS"].enabled|default(false)|lower == 'true' else false %}
	{% if swap_toolheads and is_printing_gcode %}
	{% set new_t = 0 if new_t == 1 else 1 %}
	{% endif %}
	
	
	{% set toolchange_prepurging_timer = printer["gcode_macro RatOS"].toolchange_prepurging_timer|default(0)|int %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	DEBUG_ECHO PREFIX="_SELECT_TOOL" MSG="act_t: {act_t}, new_t: {new_t}, is_printing_gcode: {is_printing_gcode}, swap_toolheads: {swap_toolheads}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	{% set act_extruder = 'extruder%s' % ('' if new_t == 0 else new_t) %}
	{% if new_t != act_t or printer.toolhead.extruder != act_extruder or idex_mode == 'reset' %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Selecting T{new_t}.."
	
	
	M220 S100
	
	
	
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(1)|int == 1 else false %}
	
	
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set toolshift = false %}
	{% endif %}
	
	
	{% set fan_speed = printer["fan_generic part_fan_t%s" % act_t].speed %}
	
	
	{% set deactivate_toolhead = false %}
	{% if is_printing_gcode %}
	{% set total_toolshifts = printer["gcode_macro START_PRINT"].total_toolshifts|int %}
	{% set toolshift_count = printer["gcode_macro _TOOLCHANGE"].toolshift_count|int + 1 %}
	SET_GCODE_VARIABLE MACRO=_TOOLCHANGE VARIABLE=toolshift_count VALUE={toolshift_count}
	{% if toolshift_count == total_toolshifts %}
	{% set deactivate_toolhead = true %}
	{% endif %}
	{% endif %}
	
	
	{% set needs_wakeup = true if printer["gcode_macro T%s" % new_t].standby|default(false)|lower == 'true' else false %}
	
	
	{% set needs_purging = false %}
	{% set wake_up_purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% if is_printing_gcode and toolchange_prepurging_timer > 0 and wake_up_purge > 0 %}
	{% set new_timestamp = printer["print_stats"].print_duration %}
	{% set elapsed_time = new_timestamp - last_timestamp %}
	SET_GCODE_VARIABLE MACRO=_SELECT_TOOL VARIABLE=last_timestamp VALUE={new_timestamp}
	{% if elapsed_time > toolchange_prepurging_timer %}
	{% set needs_purging = true %}
	{% endif %}
	{% endif %}
	
	
	{% set first_use_purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% if toolshift_count == 1 and first_use_purge > 0 %}
	{% set needs_purging = true %}
	{% endif %}
	
	
	{% if is_printing_gcode and (toolchange_standby_temp > -1 or needs_purging or needs_wakeup) %}
	_TOOLHEAD_STANDBY TOOLHEAD={act_t}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	_TOOLHEAD_WAKEUP TOOLHEAD={new_t} X={new_x} Y={new_y} Z={new_z} FAN_SPEED={fan_speed} TOOLSHIFT_COUNT={toolshift_count}
	{% else %}
	{% set sync_fans = true if printer["gcode_macro RatOS"].toolchange_sync_fans|default(false)|lower == 'true' else false %}
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if (new_t == 0 or sync_fans) else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if (new_t == 1 or sync_fans) else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	_TOOLCHANGE T={new_t} X={new_x} Y={new_y} Z={new_z} PARK_T0={park_t0} PARK_T1={park_t1} TOOLSHIFT={toolshift}
	{% if deactivate_toolhead %}
	_DEACTIVATE_TOOLHEAD TOOLHEAD={act_t}
	{% endif %}
	{% endif %}
	
	
	{% set shaper_x_freq = printer["gcode_macro RatOS"].shaper_x_freq %}
	{% set shaper_y_freq = printer["gcode_macro RatOS"].shaper_y_freq %}
	{% set shaper_x_type = printer["gcode_macro RatOS"].shaper_x_type %}
	{% set shaper_y_type = printer["gcode_macro RatOS"].shaper_y_type %}
	SET_INPUT_SHAPER SHAPER_FREQ_X={(shaper_x_freq[new_t]|float)} SHAPER_FREQ_Y={(shaper_y_freq[new_t]|float)} SHAPER_TYPE_X={(shaper_x_type[new_t]|lower)} SHAPER_TYPE_Y={(shaper_y_type[new_t]|lower)}
	
	
	SET_GCODE_VARIABLE MACRO=T0 VARIABLE=active VALUE={True if new_t == 0 else False}
	SET_GCODE_VARIABLE MACRO=T1 VARIABLE=active VALUE={True if new_t == 1 else False}
	
	
	
	{% if 'x' in printer.toolhead.homed_axes %}
	{% set sanity_check_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if new_t == 0 %}
	{% if printer.toolhead.extruder == 'extruder' %}
	{% if sanity_check_idex_mode == 'primary' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% elif new_t == 1 %}
	{% if printer.toolhead.extruder == 'extruder1' %}
	{% if sanity_check_idex_mode == 'inactive' %}
	{ action_emergency_stop("Switched states detected in idex_mode.py. Please restart the host controller.") }
	{% endif %}
	{% endif %}
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	
	{% endif %}
	{% endif %}
	{% endif %}

[gcode_macro _TOOLHEAD_STANDBY]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set toolchange_standby_temp = printer["gcode_macro RatOS"].toolchange_standby_temp|default(-1)|float %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Putting toolhead T{toolhead} into standby mode."
	DEBUG_ECHO PREFIX="_TOOLHEAD_STANDBY" MSG="toolhead: {toolhead}, config_z_hop: {config_z_hop}, toolchange_standby_temp: {toolchange_standby_temp}"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={toolhead} SYNC=0
	PARK_TOOLHEAD
	
	
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={toolchange_standby_temp}
	{% endif %}
	
	
	{% if toolchange_standby_temp > -1 %}
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=True
	{% endif %}
	
	
	_LED_TOOLHEAD_STANDBY TOOLHEAD={toolhead}

[gcode_macro _TOOLHEAD_WAKEUP]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	{% set fan_speed = params.FAN_SPEED|float %}
	{% set new_x = params.X|default(-1)|float %}
	{% set new_y = params.Y|default(-1)|float %}
	{% set new_z = params.Z|default(-1)|float %}
	{% set toolshift_count = params.TOOLSHIFT_COUNT|default(0)|int %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_purge|default(0)|float %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% if toolshift_count == 1 %}
	{% set purge = printer["gcode_macro RatOS"].toolchange_first_purge %}
	{% endif %}
	{% set needs_wakeup = true if printer["gcode_macro T%s" % toolhead].standby|default(false)|lower == 'true' else false %}
	
	RATOS_ECHO PREFIX="IDEX" MSG="Waking up toolhead T{toolhead}. Please wait for extruder to heat up..."
	DEBUG_ECHO PREFIX="_TOOLHEAD_WAKEUP" MSG="toolhead: {toolhead}, fan_speed: {fan_speed}, new_x: {new_x}, new_y: {new_y}, new_z: {new_z}, config_z_hop: {config_z_hop}"
	
	
	_LED_TOOLHEAD_WAKEUP TOOLHEAD={toolhead}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={toolhead} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE=1
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if toolhead == 0 else toolhead}
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% set extruder_first_layer_temp = (printer["gcode_macro START_PRINT"].extruder_first_layer_temp|default("")).split(",") %}
	{% set extruder_other_layer_temp = (printer["gcode_macro START_PRINT"].extruder_other_layer_temp|default("")).split(",") %}
	
	
	{% if needs_wakeup %}
	{% if printer["gcode_macro _ON_LAYER_CHANGE"].layer_number|int < 2 %}
	{% set temp = extruder_first_layer_temp[toolhead]|float %}
	{% else %}
	{% set temp = extruder_other_layer_temp[toolhead]|float %}
	{% endif %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={'extruder' if toolhead == 0 else 'extruder1'} MINIMUM={temp}  MAXIMUM={temp + 5}
	{% endif %}
	
	
	_LED_PRINTING TOOLHEAD={toolhead}
	
	
	{% if purge > 0 %}
	_MOVE_TO_LOADING_POSITION TOOLHEAD={toolhead} AUTOMATED=True
	_PURGE_FILAMENT TOOLHEAD={toolhead} E={purge}
	_CLEANING_MOVE TOOLHEAD={toolhead} AUTOMATED=True
	{% endif %}
	
	
	{% if fan_speed > 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={fan_speed if toolhead == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={fan_speed if toolhead == 1 else 0}
	
	
	M106.1 S{fan_speed}
	{% endif %}
	
	
	G92 E0
	G1 E-{e} F{feedrate}
	G92 E0
	
	
	{% if new_x >= 0 and new_y >= 0 %}
	G1 X{new_x} Y{new_y} F{speed}
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={config_z_hop} T={toolhead} SYNC=0
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	
	SET_GCODE_VARIABLE MACRO=T{toolhead} VARIABLE=standby VALUE=False

[gcode_macro _TOOLCHANGE]
variable_toolshift_count = 0
gcode = 
	
	
	{% set new_t = params.T|default(-1)|int %}
	{% set new_x = params.X|default(-1.0)|float %}
	{% set new_y = params.Y|default(-1.0)|float %}
	{% set new_z = params.Z|default(-1.0)|float %}
	{% set park_t0 = params.PARK_T0|default(-1)|float %}
	{% set park_t1 = params.PARK_T1|default(-1)|float %}
	{% set toolshift = true if params.TOOLSHIFT|default(true)|lower == 'true' else false %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T: {new_t}, X: {new_x}, Y: {new_y}, Z: {new_z}, PARK_T0: {park_t0}, PARK_T1: {park_t1}, IS_PRINTING_GCODE: {is_printing_gcode}, TOOLSHIFT: {toolshift}"
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set config_z_hop = printer["gcode_macro RatOS"].toolchange_zhop|default(2.0)|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set center_x = printable_x_max / 2 %}
	{% set acceleration = printer["gcode_macro RatOS"].toolchange_travel_accel %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% set parking_position_act_t = printer["gcode_macro T%s" % act_t].parking_position|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	{% if park_t0 >= 0 and park_t1 >= 0 %}
	{% set parking_position_t0 = park_t0 %}
	{% set parking_position_t1 = park_t1 %}
	{% set parking_position_act_t = park_t0 if act_t == 0 else park_t1 %}
	{% endif %}
	
	
	{% if not is_printing_gcode and not toolshift %}
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Changing tool to T{new_t} without retracting/extruding or moving the toolheads except for parking."
	
	
	{% if "xyz" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t} MODE=PRIMARY
	
	
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	G90
	
	
	{% set max_accel = printer.toolhead.max_accel|float %}
	{% set square_corner_velocity = printer.toolhead.square_corner_velocity|float %}
	SET_VELOCITY_LIMIT ACCEL={acceleration} MINIMUM_CRUISE_RATIO=0 SQUARE_CORNER_VELOCITY=20
	
	
	{% if not is_printing_gcode and toolshift and new_x < 0 and new_y < 0 %}
	{% set new_x = center_x %}
	{% set new_y = printer.gcode_move.gcode_position.y|float %}
	{% endif %}
	
	{% if new_x < 0 or new_y < 0 %}
	
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="No new X or Y position given, parking the active toolhead and activating the new toolhead without moving it."
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={config_z_hop} T={new_t}
	
	
	{% if "x" in printer.toolhead.homed_axes %}
	G1 X{parking_position_act_t} F{speed}
	{% endif %}
	
	
	{% if is_printing_gcode %}
	_EXTRUDE T={new_t}
	{% endif %}
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET MOVE={1 if "xyz" in printer.toolhead.homed_axes else 0}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	{% if "xyz" not in printer.toolhead.homed_axes %}
	
	
	
	SET_DUAL_CARRIAGE CARRIAGE={new_t}
	_SET_TOOLHEAD_OFFSET
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% else %}
	
	
	
	{% set svv = printer.save_variables.variables %}
	{% if new_t == default_toolhead %}
	{% set new_xoffset = 0 %}
	{% set new_yoffset = 0 %}
	{% set new_zoffset = 0 %}
	{% else %}
	{% set new_xoffset = -svv.idex_xoffset %}
	{% set new_yoffset = -svv.idex_yoffset %}
	{% set new_zoffset = -svv.idex_zoffset %}
	{% endif %}
	
	{% set xoffset_correction = new_xoffset - printer.named_offsets.toolhead_alignment.x %}
	{% set yoffset_correction = new_yoffset - printer.named_offsets.toolhead_alignment.y %}
	{% set zoffset_correction = new_zoffset - printer.named_offsets.toolhead_alignment.z %}
	
	{% if new_t == 0 %}
	
	{% set t0_act_x = parking_position_t0 %}
	{% set t1_act_x = printer.toolhead.position.x|float %}
	{% set t0_new_x = new_x %}
	{% set t1_new_x = parking_position_t1 %}
	{% set t0_distance = t0_new_x - t0_act_x %}
	{% set t1_distance = t1_new_x - t1_act_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T0."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	
	
	G1 X{t0_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x + (t1_new_x - t1_act_x)} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t0_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T0: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% elif new_t == 1 %}
	
	{% set t0_act_x = printer.toolhead.position.x|float %}
	{% set t1_act_x = parking_position_t1 %}
	{% set t0_new_x = parking_position_t0 %}
	{% set t1_new_x = new_x %}
	{% set t0_distance = t0_act_x - t0_new_x %}
	{% set t1_distance = t1_act_x - t1_new_x %}
	
	
	
	{% set calc_z_hop = config_z_hop %}
	
	
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="Shifting to T1."
	DEBUG_ECHO PREFIX="_TOOLCHANGE" MSG="T0_ACT_X: {t0_act_x}, T1_ACT_X: {t1_act_x}, T0_NEW_X: {t0_new_x}, T1_NEW_X: {t1_new_x}, T0_DISTANCE: {t0_distance}, T1_DISTANCE: {t1_distance}"
	_ZHOP_BEFORE_TOOLCHANGE Z_HOP={calc_z_hop} T={new_t} SYNC=1
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_act_x} F{speed}
	
	{% if t0_distance >= t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_act_x - t1_distance + xoffset_correction} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	G1 X{t0_new_x + xoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	
	{% elif t0_distance < t1_distance %}
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=COPY
	G1 X{t0_new_x} Y{new_y + yoffset_correction} F{speed}
	
	
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{t1_new_x + xoffset_correction} F{speed}
	
	{% endif %}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment X={new_xoffset} Y={new_yoffset} MOVE=0 SPEED={speed}
	G1 X{t1_new_x} Y{new_y} F{speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={new_zoffset} MOVE=1 SPEED={z_speed}
	RATOS_ECHO PREFIX="IDEX" MSG="Toolhead offset applied for T1: X={new_xoffset} Y={new_yoffset} Z={new_zoffset}"
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}
	
	
	
	{% set calc_z_drop = config_z_hop %}
	
	
	_ZDROP_AFTER_TOOLCHANGE Z_DROP={calc_z_drop} T={new_t} SYNC=1
	
	{% endif %}
	
	
	ACTIVATE_EXTRUDER EXTRUDER=extruder{'' if new_t == 0 else new_t}
	
	{% endif %}
	{% endif %}
	
	
	SET_VELOCITY_LIMIT ACCEL={max_accel} MINIMUM_CRUISE_RATIO=0.5 SQUARE_CORNER_VELOCITY={square_corner_velocity}
	
	{% endif %}

[gcode_macro _ZHOP_BEFORE_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_hop = params.Z_HOP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_retraction %}
	
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_HOP: {z_hop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="COMBINED_ZHOP G1 Z+{z_hop} E-{e} F{speed * 60}"
	G1 Z+{z_hop} E-{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="ZHOP G1 Z+{z_hop} F{speed * 60}"
	G1 Z+{z_hop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="RETRACT G1 E-{e} F{feedrate}"
	G1 E-{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZHOP_BEFORE_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _ZDROP_AFTER_TOOLCHANGE]
gcode = 
	
	{% set t = params.T|int %}
	{% set sync = params.SYNC|default(0)|int %}
	{% set z_drop = params.Z_DROP|default(0.0)|float %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_zspeed|default(25)|float %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	{% set combined_zhop = true if printer["gcode_macro RatOS"].toolchange_combined_zhop|default(true)|lower == 'true' else false %}
	{% set both_toolheads = true if printer["gcode_macro START_PRINT"].both_toolheads|default(true)|lower == 'true' else false %}
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="T: {t}, BOTH_TOOLHEADS: {both_toolheads}, SYNC: {sync}, IS_PRINTING_GCODE: {is_printing_gcode}, Z_DROP: {z_drop}"
	
	G91
	M82
	G92 E0
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder1
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder
	{% endif %}
	{% endif %}
	
	
	{% if combined_zhop and is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="COMBINED_ZDROP G1 Z-{z_drop} E{e} F{speed * 60}"
	G1 Z-{z_drop} E{e} F{speed * 60}
	{% else %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="ZDROP G1 Z-{z_drop} F{speed * 60}"
	G1 Z-{z_drop} F{speed * 60}
	{% if is_printing_gcode %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="EXTRUDE G1 E{e} F{feedrate}"
	G1 E{e} F{feedrate}
	{% endif %}
	{% endif %}
	
	
	{% if sync == 1 and t == 0 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder MOTION_QUEUE=extruder
	{% endif %}
	{% elif sync == 1 and t == 1 and is_printing_gcode and both_toolheads %}
	{% if printer['extruder'].can_extrude|lower == 'true' and printer['extruder1'].can_extrude|lower == 'true' %}
	DEBUG_ECHO PREFIX="_ZDROP_AFTER_TOOLCHANGE" MSG="UNSYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1"
	SYNC_EXTRUDER_MOTION EXTRUDER=extruder1 MOTION_QUEUE=extruder1
	{% endif %}
	{% endif %}
	
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _EXTRUDE]
gcode = 
	
	{% set t = params.T|int %}
	
	
	{% set e = printer["gcode_macro RatOS"].toolchange_extrusion %}
	{% set feedrate = printer["gcode_macro RatOS"].toolchange_feedrate %}
	
	DEBUG_ECHO PREFIX="_EXTRUDE" MSG="G1 E{e} F{feedrate * 60}"
	
	
	G91
	M82
	G92 E0
	G1 E{e} F{feedrate * 60}
	G90
	G92 E0
	_SET_EXTRUSION_MODE

[gcode_macro _DEACTIVATE_TOOLHEAD]
gcode = 
	
	{% set toolhead = params.TOOLHEAD|int %}
	
	DEBUG_ECHO PREFIX="_DEACTIVATE_TOOLHEAD" MSG="TOOLHEAD {toolhead}"
	
	
	{% if toolhead == 0 %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	{% endif %}
	
	
	M106.1 S0
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if toolhead == 0 else 'extruder1'} TARGET=0
	
	
	_LED_DEACTIVATE_TOOLHEAD TOOLHEAD={toolhead}

[delayed_gcode _INIT_TOOLHEADS]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|int %}
	
	
	_IDEX_SINGLE INIT=1
	
	
	{% if printer.fastconfig.settings.dual_carriage.safe_distance is defined %}
	{% if printer.fastconfig.settings.dual_carriage.safe_distance|float < 50 %}
	{ action_emergency_stop("Dual carriage safe_distance seems to be too low!") }
	{% endif %}
	{% else %}
	{ action_emergency_stop("Dual carriage safe_distance not defined!") }
	{% endif %}

[gcode_macro _SET_TOOLHEAD_OFFSET]
description = "Internal use only. Sets the toolhead_alignment offset (and hotend_thermal_expansion offset when configured) for the active/dominant toolhead."
gcode = 
	
	{% set move = params.MOVE|default(0)|int %}
	{% set force_toolhead = params.FORCE_TOOLHEAD|default(-1)|int %}
	
	
	{% if params.T is defined %}
	CONSOLE_ECHO TYPE="error" MSG="_SET_TOOLHEAD_OFFSET called with deprectated T parameter, which is ignored."
	{';$_SET_TOOLHEAD_OFFSET_ignoring_TOOLHEAD_parameter'}
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="active/dominant toolhead: {toolhead}, MOVE: {move}, FORCE_TOOLHEAD: {force_toolhead}"
	
	
	{% if force_toolhead >= 0 %}
	{% set toolhead = force_toolhead %}
	DEBUG_ECHO PREFIX="_SET_TOOLHEAD_OFFSET" MSG="FORCE_TOOLHEAD applied, using TOOLHEAD: {toolhead}"
	{% endif %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set is_printing_gcode = true if printer["gcode_macro START_PRINT"].is_printing_gcode|default(true)|lower == 'true' else false %}
	
	
	{% if "xyz" not in printer.toolhead.homed_axes %}
	{% set move = 0 %}
	{% endif %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|int %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X=0 Y=0 MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z=0 MOVE={move} SPEED={z_speed}
	{% else %}
	{% set svv = printer.save_variables.variables %}
	SET_NAMED_OFFSET NAME=toolhead_alignment X={(-svv.idex_xoffset)} Y={(-svv.idex_yoffset)} MOVE={move} SPEED={speed}
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-svv.idex_zoffset)} MOVE={move} SPEED={z_speed}
	{% endif %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and is_printing_gcode %}
	_BEACON_SET_NOZZLE_TEMP_OFFSET
	{% endif %}

[gcode_macro TOOLSHIFT_CONFIG]
gcode = 
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={params.SPEED|default(300)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={params.ACCEL|default(5000)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_retraction VALUE={params.RETRACT|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_extrusion VALUE={params.EXTRUDE|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_feedrate VALUE={params.FEEDRATE|default(7200)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={params.Z_HOP|default(2.0)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zspeed VALUE={params.Z_SPEED|default(25)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_combined_zhop VALUE={true if params.COMBINED_ZHOP|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_sync_fans VALUE={true if params.SYNC_FANS|default(0)|int == 1 else false}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_prepurging_timer VALUE={params.AUTO_PURGE_TIME|default(0)|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_purge VALUE={params.PURGE|default(25)|float}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_standby_temp VALUE={params.STANDBY_TEMP|default(-1)|float}

[gcode_macro CALCULATE_DC_ENDSTOP]
description = "DEPRECATED: This macro has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."
gcode = 
	CONSOLE_ECHO TITLE="CALCULATE_DC_ENDSTOP has been deprecated" TYPE="error" MSG="The CALCULATE_DC_ENDSTOP has been deprecated. Please use CONFIGURE_DC_ENDSTOP instead."

[gcode_macro _VAOC]
variable_is_fixed = True
variable_is_started = False
variable_is_started_at_temp = False
variable_additional_safe_distance = 50
variable_safe_z = 30
variable_auto_z_offset_calibration = True
variable_enable_camera_cooling = True
variable_camera_cooling_fan_speed = 0.3
variable_camera_cooling_temperature = 50
variable_toolchange_travel_speed = 300
variable_toolchange_travel_accel = 5000
variable_adjusting_secondary_toolhead_focus_adjusts_zoffset = False
variable_cache_toolchange_travel_speed = 300
variable_cache_toolchange_travel_accel = 5000
variable_cache_toolchange_zhop = 1.0
variable_t0_toolhead_sensor_enabled = 0
variable_t1_toolhead_sensor_enabled = 0
variable_t0_bowden_sensor_enabled = 0
variable_t1_bowden_sensor_enabled = 0
variable_loaded_skew_profile = ""
variable_gcode_z_offset = 0.0
variable_start_x_offset = 0.0
variable_start_y_offset = 0.0
gcode = 
	_ECHO_VAOC_VARS
variable_expected_camera_x_position = 212.5
variable_expected_camera_y_position = 530.5

[gcode_macro _VAOC_START]
description = Called from the front end. If T0_TEMP, T1_TEMP and BED_TEMP parameter are specified, VAOC calibration will start under real conditions at printing temp.
gcode = 
	
	{% set t0_temp = params.T0_TEMP|default(0)|int %}
	{% set t1_temp = params.T1_TEMP|default(0)|int %}
	{% set bed_temp = params.BED_TEMP|default(0)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro SKEW_PROFILE"].loaded_profile|default("") %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=loaded_skew_profile VALUE='"{loaded_skew_profile}"'
	
	
	{% if t0_temp > 0 and t1_temp > 0 and bed_temp > 0 %}
	
	
	{% if not is_fixed %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("VAOC calibration at temp works only with a fixed installed VAOC device.") }
	{% endif %}
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_toolhead_sensor_enabled VALUE={1 if printer["filament_switch_sensor toolhead_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t0_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t0"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE=0
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=t1_bowden_sensor_enabled VALUE={1 if printer["filament_switch_sensor bowden_filament_sensor_t1"].enabled|lower == "true" else 0}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE=0
	{% endif %}
	
	
	START_PRINT EXTRUDER_TEMP={t0_temp},{t1_temp} EXTRUDER_OTHER_LAYER_TEMP={t0_temp},{t1_temp} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp} INITIAL_TOOL=0 TOTAL_LAYER_COUNT=1 X0={(printable_x_max / 2 - 10)} Y0={(printable_y_max / 2 - 10)} X1={(printable_x_max / 2 + 10)} Y1={(printable_y_max / 2 + 10)} TOTAL_TOOLSHIFTS=1 FIRST_X={printable_x_max / 2} FIRST_Y={printable_y_max / 2} MIN_X={(printable_x_max / 2 - 10)} MAX_X={(printable_x_max / 2 + 10)} USED_TOOLS=0,1
	
	
	SET_GCODE_VARIABLE MACRO=START_PRINT VARIABLE=is_printing_gcode VALUE=False
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=True
	
	{% endif %}
	
	
	_START_VAOC

[gcode_macro _START_VAOC]
description = Called from _VAOC_START. Do not call it manually.
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(printable_x_max/2)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(printable_y_max/2)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	DEBUG_ECHO PREFIX="VAOC_START" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, zcontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_x_offset VALUE={svv.idex_xoffset|default(0.0)|float}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=start_y_offset VALUE={svv.idex_yoffset|default(0.0)|float}
	
	
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_SAFE_Z_HEIGHT
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_speed VALUE={printer["gcode_macro RatOS"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_travel_accel VALUE={printer["gcode_macro RatOS"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=cache_toolchange_zhop VALUE={printer["gcode_macro RatOS"].toolchange_zhop|float}
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE=0
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"START X_REFERENCE:%.6f Y_REFERENCE:%.6f Z_REFERENCE:%.6f PARK_T0:%.6f PARK_T1:%.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, parking_position_t0, parking_position_t1)}
	
	
	_LED_VAOC_ON
	
	
	
	
	
	
	
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=gcode_z_offset VALUE={printer.gcode_move.homing_origin.z}
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z=0
	
	
	MAYBE_HOME
	M400
	
	
	_LOAD_RATOS_SKEW_PROFILE
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	{% if printer.toolhead.position.y|float > printable_y_max %}
	G1 Y{printable_y_max} F{speed}
	{% endif %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% if idex_mode == "copy" or idex_mode == "mirror" %}
	IDEX_SINGLE
	{% endif %}
	
	
	
	SAVE_GCODE_STATE NAME=vaoc_state
	
	
	RESET_NAMED_OFFSET EVENT=reset_all
	
	
	{% if is_fixed %}
	_SELECT_TOOL T=0 TOOLSHIFT=false
	{% if default_toolhead == 0 %}
	G1 X{idex_xcontrolpoint} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint + safe_distance + additional_safe_distance} F{speed}
	{% else %}
	G1 X{idex_xcontrolpoint - safe_distance - additional_safe_distance} F{speed}
	SET_DUAL_CARRIAGE CARRIAGE=1 MODE=PRIMARY
	G1 X{idex_xcontrolpoint} F{speed}
	{% endif %}
	SET_DUAL_CARRIAGE CARRIAGE=0 MODE=PRIMARY
	{% else %}
	_SELECT_TOOL T={default_toolhead} TOOLSHIFT=false
	{% endif %}
	
	
	G1 X{idex_xcontrolpoint} F{speed}
	G1 Y{idex_ycontrolpoint} F{speed}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	
	
	_SELECT_TOOL T={default_toolhead} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	{% if not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={default_toolhead}
	{% endif %}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=True

[gcode_macro _VAOC_END]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set center_y = printable_y_max / 2 %}
	{% set saved_gcode_z_offset = printer["gcode_macro _VAOC"].gcode_z_offset|default(0.0)|float %}
	
	DEBUG_ECHO PREFIX="_VAOC_END" MSG="printable_y_max: {printable_y_max}, center_y: {center_y}, safe_z: {safe_z}"
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% set x_offset_change = svv.idex_xoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_x_offset|default(0.0)|float %}
	{% set y_offset_change = svv.idex_yoffset|default(0.0)|float - printer["gcode_macro _VAOC"].start_y_offset|default(0.0)|float %}
	{% set offset_change_norm = (x_offset_change ** 2 + y_offset_change ** 2) ** 0.5 %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="VAOC calibration changed the relative XY offset between T0 and T1 by {offset_change_norm|round(3)} mm (ΔX: {x_offset_change|round(3)}, ΔY: {y_offset_change|round(3)})"
	
	
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	
	{% if printer.toolhead.position.z|float < safe_z %}
	G1 Z{safe_z} F{z_speed}
	{% endif %}
	
	
	G1 Y{center_y} F{speed}
	
	
	_IDEX_SINGLE INIT=1
	
	
	_LED_VAOC_OFF
	
	
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_speed VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_speed|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_travel_accel VALUE={printer["gcode_macro _VAOC"].cache_toolchange_travel_accel|int}
	SET_GCODE_VARIABLE MACRO=RatOS VARIABLE=toolchange_zhop VALUE={printer["gcode_macro _VAOC"].cache_toolchange_zhop|float}
	
	
	{% if printer["gcode_macro _VAOC"].is_started_at_temp|default(true)|lower == 'true' %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=toolhead_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_toolhead_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t0"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t0 ENABLE={printer["gcode_macro _VAOC"].t0_bowden_sensor_enabled|int}
	{% endif %}
	{% if printer["filament_switch_sensor bowden_filament_sensor_t1"] is defined %}
	SET_FILAMENT_SENSOR SENSOR=bowden_filament_sensor_t1 ENABLE={printer["gcode_macro _VAOC"].t1_bowden_sensor_enabled|int}
	{% endif %}
	{% endif %}
	
	
	{% set loaded_skew_profile = printer["gcode_macro _VAOC"].loaded_skew_profile|default("") %}
	{% if loaded_skew_profile != "" %}
	SKEW_PROFILE LOAD={loaded_skew_profile}
	{% else %}
	SET_SKEW CLEAR=1
	{% endif %}
	
	
	RESTORE_GCODE_STATE NAME=vaoc_state
	
	
	SET_GCODE_OFFSET X=0 Y=0 Z={saved_gcode_z_offset}
	
	
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started VALUE=False
	SET_GCODE_VARIABLE MACRO=_VAOC VARIABLE=is_started_at_temp VALUE=False

[gcode_macro _VAOC_LOAD_TOOL]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set auto_temp_offset = true if params.AUTO_TEMP_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set safe_distance = printer.fastconfig.settings.dual_carriage.safe_distance|float %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	{% set additional_safe_distance = printer["gcode_macro _VAOC"].additional_safe_distance|float %}
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set toolhead_zoffset = svv.idex_zoffset|default(0)|float %}
	
	
	{% if auto_z_offset %}
	{% set additional_safe_distance = 20 %}
	{% set idex_xcontrolpoint = idex_xcontrolpoint + z_offset_probe_x_offset %}
	{% set idex_ycontrolpoint = idex_ycontrolpoint + z_offset_probe_y_offset %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move T%s to control point: X%.6f Y%.6f Z%.6f IS_FIXED=%s"' % (t, idex_xcontrolpoint, idex_ycontrolpoint, idex_zcontrolpoint, is_fixed)}
	
	
	{% if not auto_temp_offset and not auto_z_offset %}
	_VAOC_SET_CAMERA_COOLING T={t}
	{% endif %}
	
	
	{% set parking_position_t0 = printer["gcode_macro T0"].parking_position|float %}
	{% set parking_position_t1 = printer["gcode_macro T1"].parking_position|float %}
	{% if is_fixed %}
	{% set parking_position_t0 = idex_xcontrolpoint - safe_distance - additional_safe_distance %}
	{% set parking_position_t1 = idex_xcontrolpoint + safe_distance + additional_safe_distance %}
	{% endif %}
	
	
	{% set current_z = printer.toolhead.position.z|float %}
	{% set lowest_toolhead_z = [current_z, current_z - toolhead_zoffset]|min %}
	{% if lowest_toolhead_z < safe_z %}
	G1 Z{[safe_z, safe_z + toolhead_zoffset]|max} F{z_speed}
	{% else %}
	G1 Z{idex_zcontrolpoint} F{z_speed}
	{% endif %}
	
	
	_SELECT_TOOL T={t} X={idex_xcontrolpoint} Y={idex_ycontrolpoint} PARK_T0={parking_position_t0} PARK_T1={parking_position_t1}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_SET_CAMERA_COOLING]
gcode = 
	
	{% set t = params.T|default(0)|int %}
	
	
	{% set enable_camera_cooling = true if printer["gcode_macro _VAOC"].enable_camera_cooling|default(true)|lower == 'true' else false %}
	{% set camera_cooling_temperature = printer["gcode_macro _VAOC"].camera_cooling_temperature|float %}
	{% set camera_cooling_fan_speed = printer["gcode_macro _VAOC"].camera_cooling_fan_speed|float %}
	
	
	{% if printer.heater_bed.temperature >= camera_cooling_temperature and enable_camera_cooling %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED={camera_cooling_fan_speed if t == 0 else 0}
	SET_FAN_SPEED FAN=part_fan_t1 SPEED={camera_cooling_fan_speed if t == 1 else 0}
	
	
	M106.1 S{camera_cooling_fan_speed}
	
	{% else %}
	SET_FAN_SPEED FAN=part_fan_t0 SPEED=0
	SET_FAN_SPEED FAN=part_fan_t1 SPEED=0
	
	
	M106.1 S0
	
	{% endif %}

[gcode_macro _VAOC_SET_TOOL]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	DEBUG_ECHO PREFIX="_VAOC_SET_TOOL" MSG="IDEX_MODE: {idex_mode}, TOOLHEAD: {toolhead}"
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	{% set x = printer.gcode_move.gcode_position.x|float %}
	{% set y = printer.gcode_move.gcode_position.y|float %}
	{% set z = printer.gcode_move.gcode_position.z|float %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE={x}
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE={y}
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE={z}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"Control point was set: X%.6f Y%.6f Z%.6f"' % (x, y, z)}
	
	{% else %}
	
	
	
	{% set move_diff_x = printer.gcode_move.gcode_position.x|float - svv.idex_xcontrolpoint|float %}
	{% set move_diff_y = printer.gcode_move.gcode_position.y|float - svv.idex_ycontrolpoint|float %}
	{% set move_diff_z = printer.gcode_move.gcode_position.z|float - svv.idex_zcontrolpoint|float %}
	
	
	{% set new_x_offset = svv.idex_xoffset - move_diff_x %}
	{% set new_y_offset = svv.idex_yoffset - move_diff_y %}
	{% set new_z_offset = svv.idex_zoffset - move_diff_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE={new_x_offset}
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE={new_y_offset}
	
	{% set z_focus_msg = "" %}
	{% if move_diff_z|abs > 1e-6 %}
	{% if printer["gcode_macro _VAOC"].adjusting_secondary_toolhead_focus_adjusts_zoffset|default(false)|lower == 'true' %}
	{% set z_focus_msg = " (Z offset adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={new_z_offset}
	{% else %}
	{% set z_focus_msg = " (Z offset not adjusted to follow T1 focus adjustment, see VAOC setting 'adjusting_secondary_toolhead_focus_adjusts_zoffset')" %}
	{% set new_z_offset = svv.idex_zoffset %}
	{% endif %}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset was set: X%.6f Y%.6f Z%.6f%s"' % (toolhead, new_x_offset, new_y_offset, new_z_offset, z_focus_msg)}
	
	{% endif %}

[gcode_macro _VAOC_MOVE]
gcode = 
	
	{% set x = params.X|default(0)|float %}
	{% set y = params.Y|default(0)|float %}
	{% set z = params.Z|default(0)|float %}
	
	
	G91
	{% if z != 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 Z%.6f F300"' % (z)}
	G1 Z{z} F300
	
	{% else %}
	{% if x <=2 and y <=2 %}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Move toolhead: G1 X%.6f Y%.6f F18000"' % (x, y)}
	G1 X{x} Y{y} F18000
	{% endif %}
	{% endif %}
	G90

[gcode_macro _VAOC_CALIBRATE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	{% if printer["z_offset_probe"] is defined and is_started %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	
	{% if auto_z_offset %}
	_START_VAOC AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_Z_OFFSET=True
	_VAOC_PROBE_Z_OFFSET AUTO_Z_OFFSET=True
	_VAOC_END
	{% else %}
	_VAOC_LOAD_TOOL T={default_toolhead}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1}
	_VAOC_PROBE_Z_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	{% endif %}
	
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_Z_OFFSET
	
	{% endif %}

[gcode_macro _VAOC_PROBE_Z_OFFSET]
gcode = 
	
	{% set auto_z_offset = true if params.AUTO_Z_OFFSET|default(false)|lower == 'true' else false %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}
	{% if not auto_z_offset %}
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	{% endif %}
	M400
	_VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT

[gcode_macro _VAOC_Z_OFFSET_PROBE_CURRENT_POSITION]
gcode = 
	
	Z_OFFSET_PROBE PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_DROP=1 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median

[gcode_macro _VAOC_Z_OFFSET_PROBE_SAVE_PROBE_RESULT]
gcode = 
	{% if printer["z_offset_probe"] is defined %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	{% if toolhead == printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE={last_z}
	RATOS_ECHO PREFIX="VAOC" MSG={'"Z-offset control point set:: %.6f"' % last_z}
	
	{% else %}
	
	
	
	{% set z = svv.idex_zoffsetcontrolpoint|float - last_z %}
	
	
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE={z}
	
	
	SET_NAMED_OFFSET NAME=toolhead_alignment Z={(-z)}
	
	
	G0 Z{svv.idex_zcontrolpoint|float} F{z_speed}
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s offset set: Z %.6f"' % (t, z)}
	
	{% endif %}
	
	{% endif %}

[gcode_macro _VAOC_ECHO_Z_OFFSET]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG={'"T%s toolhead z-offset %.6f"' % (1 if default_toolhead == 0 else 0, svv.idex_zoffset)}
	{% if svv.idex_zoffset|abs < 0.02 %}
	CONSOLE_ECHO TITLE={'"Perfect toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="You have a perfect toolhead z-offset!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.02 and svv.idex_zoffset|abs < 0.05 %}
	CONSOLE_ECHO TITLE={'"Good toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is good!" TYPE="success"
	{% elif svv.idex_zoffset|abs >= 0.05 and svv.idex_zoffset|abs < 0.1 %}
	CONSOLE_ECHO TITLE={'"High toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset could be better._N_Use minimum 0.3mm first layer height for copy and mirror mode prints." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.1 and svv.idex_zoffset|abs < 0.2 %}
	CONSOLE_ECHO TITLE={'"Bad toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is bad._N_Copy and mirror mode prints are not recommended with it." TYPE="warning"
	{% elif svv.idex_zoffset|abs >= 0.2 %}
	CONSOLE_ECHO TITLE={'"Unacceptable toolhead z-offset of %.6fmm!"' % svv.idex_zoffset} MSG="Your toolhead z-offset is unacceptable._N_Do not print in copy and mirror mode with it." TYPE="alert"
	{% endif %}
	RATOS_ECHO PREFIX="VAOC" MSG="Toolhead z-offset calibration done!"

[gcode_macro _VAOC_CALIBRATE_TEMP_OFFSET]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set is_started = true if printer["gcode_macro _VAOC"].is_started|default(false)|lower == 'true' else false %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if is_fixed and is_started and printer["z_offset_probe"] is defined and printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT
	_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS
	_VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED
	
	
	_VAOC_SET_TOOL
	
	
	{% set act_z = printer.toolhead.position.z|float %}
	_VAOC_LOAD_TOOL T={default_toolhead} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={0 if default_toolhead == 1 else 1} AUTO_TEMP_OFFSET=True
	_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET
	_VAOC_LOAD_TOOL T={default_toolhead}
	G1 Z{act_z} F{z_speed}
	
	
	_VAOC_ECHO_NOZZLE_TEMP_OFFSETS
	
	{% endif %}

[gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	M400
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_VAOC_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_VAOC_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET=0
	
	
	G1 X{idex_xcontrolpoint} Y{idex_ycontrolpoint} F{speed}
	M400

[gcode_macro _VAOC_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(150)|float %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO PREFIX="VAOC" MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="VAOC" MSG="Probing with nozzle temperature {temp}°C..."
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	
	
	G0 Z{idex_zcontrolpoint} F{z_speed}

[gcode_macro _VAOC_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if idex_mode=='primary' else 0 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=_VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro _VAOC_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _VAOC_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set msg = '"T0 expansion coefficient %.6fmm_N_T1 expansion coefficient %.6fmm"' % (svv.nozzle_expansion_coefficient_t0, svv.nozzle_expansion_coefficient_t1) %}
	CONSOLE_ECHO TITLE="Nozzle expansion coefficients:" MSG={msg} TYPE="success"

[gcode_macro _VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	{% set expected_camera_x_position = printer["gcode_macro _VAOC"].expected_camera_x_position|default(0)|float %}
	{% set expected_camera_y_position = printer["gcode_macro _VAOC"].expected_camera_y_position|default(0)|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_CONTROL_POINT_WITHIN_EXPECTED_CAMERA_POS" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f, expected_camera_x_position: %.6f, expected_camera_y_position: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint, expected_camera_x_position, expected_camera_y_position)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - expected_camera_x_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC x-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_xcontrolpoint, expected_camera_x_position)) }
	{% endif %}
	{% if (idex_ycontrolpoint - expected_camera_y_position)|abs > 5 %}
	M84
	{ action_raise_error("VAOC y-control coordinate is set to %.3f but is expected to be within 5mm of %.3f. Please run '_VAOC_RESET' to roll back to default values." % (idex_ycontrolpoint, expected_camera_y_position)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT]
gcode = 
	
	{% set is_fixed = true if printer["gcode_macro _VAOC"].is_fixed|default(true)|lower == 'true' else false %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(0)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_TOOLHEAD_WITHIN_CONTROL_POINT" MSG={'"xcontrolpoint: %.6f, ycontrolpoint: %.6f"' % (idex_xcontrolpoint, idex_ycontrolpoint)}
	
	{% if is_fixed %}
	{% if (idex_xcontrolpoint - printer.gcode_move.gcode_position.x|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected y-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_xcontrolpoint, printer.gcode_move.gcode_position.x|float)) }
	{% endif %}
	{% if (idex_ycontrolpoint - printer.gcode_move.gcode_position.y|float)|abs > 3 %}
	M84
	{ action_raise_error("Unexpected x-coordinate detected, VAOC aborted. Expected %.3f but got %.3f." % (idex_ycontrolpoint, printer.gcode_move.gcode_position.y|float)) }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_ENSURE_SAFE_Z_HEIGHT]
gcode = 
	
	{% set safe_z = printer["gcode_macro _VAOC"].safe_z|float %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	{% set idex_zoffsetcontrolpoint = svv.idex_zoffsetcontrolpoint|default(0)|float %}
	
	
	DEBUG_ECHO PREFIX="_VAOC_ENSURE_SAFE_Z_HEIGHT" MSG={'"idex_zcontrolpoint: %.6f, idex_zoffsetcontrolpoint: %.6f"' % (idex_zcontrolpoint, idex_zoffsetcontrolpoint)}
	
	{% if safe_z < idex_zcontrolpoint + 2 or safe_z < idex_zoffsetcontrolpoint + 2 %}
	{action_raise_error("VAOC safe_z value (%.3f) is too low, it must be higher than %.3f" % (safe_z, [idex_zoffsetcontrolpoint + 2, idex_zcontrolpoint + 2]|max))}
	{% endif %}

[gcode_macro _VAOC_ENSURE_FILAMENTS_ARE_NOT_LOADED]
gcode = 
	
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t0"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T0. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"] is defined %}
	{% if printer["filament_switch_sensor toolhead_filament_sensor_t1"].filament_detected|lower == "true" %}
	_LED_START_PRINTING_ERROR
	M84
	{ action_raise_error("Filament detected in toolhead T1. Unload filament and make sure to clean the nozzle and the melting zone.") }
	{% endif %}
	{% endif %}

[gcode_macro _VAOC_RESET]
gcode = 
	DEBUG_ECHO PREFIX="_VAOC_RESET" MSG="running template-emitted _VAOC_RESET macro"
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	SAVE_VARIABLE VARIABLE=idex_xcontrolpoint VALUE=212.5
	SAVE_VARIABLE VARIABLE=idex_ycontrolpoint VALUE=530.5
	SAVE_VARIABLE VARIABLE=idex_zcontrolpoint VALUE=10
	SAVE_VARIABLE VARIABLE=idex_zoffsetcontrolpoint VALUE=0
	SAVE_VARIABLE VARIABLE=idex_xoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_yoffset VALUE=0.0
	SAVE_VARIABLE VARIABLE=idex_zoffset VALUE=0.0
	
	RESET_DC_ENDSTOP_CONFIGURATION
	RESET_Y_MAX_ADJUSTMENT
	
	
	CONSOLE_ECHO TITLE="VAOC Configuration Reset" MSG="VAOC configuration has been reset. You must RESTART klipper for the changes to take effect,_N_then re-calibrate VAOC."

[gcode_macro _ECHO_VAOC_VARS]
description = Echo VAOC variables to the console.
gcode = 
	{% for var, value in printer["gcode_macro _VAOC"].items() %}
	{action_respond_info(var ~ ": " ~ value)}
	{% endfor %}

[gcode_macro _VAOC_SWITCH_LED]
gcode = 
	{% if params.STATE|default(0)|int == 1 %}
	_LED_VAOC_ON
	{% else %}
	_LED_VAOC_OFF
	{% endif %}

[gcode_macro Z_PROBE_TEST_T0]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T0
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST_T1]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_VAOC_Z_PROBE_TEST_EVALUATE_T1
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro Z_PROBE_TEST]
gcode = 
	
	{% set debug_previously_enabled = False %}
	{% if printer["gcode_macro DEBUG_ECHO"].enabled|lower == 'true' %}
	{% set debug_previously_enabled = True %}
	{% else %}
	ENABLE_DEBUG
	{% endif %}
	
	_CLEAR_PRIMARY_TOOLHEAD_RESULT
	_CLEAR_SECONDARY_TOOLHEAD_RESULT
	
	{% if params.HOT|default(False)|lower == 'true' %}
	{% set t0_temp = params.T0_TEMP|default(150)|int %}
	{% set t1_temp = params.T1_TEMP|default(150)|int %}
	{% set bed_temp = params.BED_TEMP|default(115)|int %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Heating extruders"
	SET_HEATER_TEMPERATURE HEATER="extruder" TARGET={t0_temp}
	SET_HEATER_TEMPERATURE HEATER="extruder1" TARGET={t1_temp}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Heating bed"
	M190 S{bed_temp}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting HOT z offset probe testing"
	{% else %}
	RATOS_ECHO PREFIX="Z Offset Testing"  MSG="Starting COLD z offset probe testing"
	{% endif %}
	
	_VAOC_START
	
	
	{% for i in range(4) %}
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	{% endfor %}
	
	
	_VAOC_LOAD_TOOL T=0 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_PRIMARY_TOOLHEAD_RESULT
	
	_VAOC_Z_PROBE_LOOP
	
	_VAOC_LOAD_TOOL T=1 AUTO_Z_OFFSET=True
	_VAOC_TEST_Z_OFFSET
	_ADD_SECONDARY_TOOLHEAD_RESULT
	
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	
	
	_VAOC_Z_PROBE_TEST_EVALUATE
	
	
	{% if debug_previously_enabled == False %}
	DISABLE_DEBUG
	{% endif %}

[gcode_macro _VAOC_Z_PROBE_LOOP]
gcode = 
	_VAOC_END
	DUMP_TMC stepper="stepper_z1"
	GET_POSITION
	_SHAKE_IT
	_VAOC_START

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if primary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T0. Retried {primary_retries} time(s)."
	{% endif %}
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	
	{% if (primary_range - secondary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 is drifting significantly more than T1."
	{% endif %}
	{% if (secondary_range - primary_range) > 0.01 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 is drifting significantly more than T0."
	{% endif %}
	
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T0]
gcode = 
	
	{% set primary_results = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].results %}
	{% set primary_retries = printer["gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT"].retries %}
	
	{% if primary_results|sum > 0 and primary_results|count > 0 %}
	{% set primary_average = (primary_results|sum/(primary_results|count))|round(6) %}
	{% else %}
	{% set primary_average = 0 %}
	{% endif %}
	
	{% set primary_min = primary_results|min %}
	{% set primary_max = primary_results|max %}
	{% set primary_range = primary_max - primary_min %}
	
	{% if primary_retries > 0 %}
	{% set primary_average_retries = primary_retries/(primary_results|count) %}
	{% else %}
	{% set primary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T0 result: {primary_average}, Average Retries: {primary_average_retries}, Range: {primary_range|round(6)}, Min: {primary_min}, Max: {primary_max}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set: {primary_results}, retries: {primary_retries}"

[gcode_macro _VAOC_Z_PROBE_TEST_EVALUATE_T1]
gcode = 
	
	{% set secondary_results = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].results %}
	{% set secondary_retries = printer["gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT"].retries %}
	
	{% if secondary_results|sum > 0 and secondary_results|count > 0 %}
	{% set secondary_average = (secondary_results|sum/(secondary_results|count))|round(6) %}
	{% else %}
	{% set secondary_average = 0 %}
	{% endif %}
	
	{% set secondary_min = secondary_results|min %}
	{% set secondary_max = secondary_results|max %}
	{% set secondary_range = secondary_max - secondary_min %}
	
	{% if secondary_retries > 0 %}
	{% set secondary_average_retries = secondary_retries/(secondary_results|count) %}
	{% else %}
	{% set secondary_average_retries = 0 %}
	{% endif %}
	
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Average T1 result: {secondary_average}, Average Retries: {secondary_average_retries}, Range: {secondary_range|round(6)}, Min: {secondary_min}, Max: {secondary_max}"
	
	{% if secondary_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="Z probe has poor repeatibility for T1. Retried {secondary_retries} time(s)."
	{% endif %}
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set: {secondary_results}, retries: {secondary_retries}"

[gcode_macro _SHAKE_IT]
gcode = 
	
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	
	_Z_HOP
	{% for i in range(3) %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2 - 25}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2 + 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2 - 1}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2 + 1}
	{% endfor %}
	{% for i in range(2) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 + 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 + 50} Y{printable_y_max/2 - 50}
	G0 X{printable_x_max/2 - 50} Y{printable_y_max/2 + 50}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 25} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 25} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(5) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 25}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 25}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2 + 1} Y{printable_y_max/2}
	G0 X{printable_x_max/2 - 1} Y{printable_y_max/2}
	{% endfor %}
	{% for i in range(10) %}
	G0 X{printable_x_max/2} Y{printable_y_max/2} F{speed}
	G0 X{printable_x_max/2} Y{printable_y_max/2 + 1}
	G0 X{printable_x_max/2} Y{printable_y_max/2 - 1}
	{% endfor %}
	{% endfor %}

[gcode_macro _ADD_PRIMARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T0 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T0 retries updated: {new_retries}"

[gcode_macro _ADD_SECONDARY_TOOLHEAD_RESULT]
variable_results = []
variable_retries = 0
gcode = 
	{% set last_z = printer["z_offset_probe"].last_z_result|default(0)|float %}
	{% set last_retries = printer["z_offset_probe"].last_retries|default(0)|float %}
	{% set new_results = results + [last_z] %}
	{% set new_retries = retries + last_retries %}
	{% if last_retries > 0 %}
	RATOS_ECHO PREFIX="Z Offset Testing" MSG="T1 probe repeatibility issues detected! Retried {last_retries} time(s)."
	{% endif %}
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="{new_results}"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE="{new_retries}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 result set updated: {new_results}"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="T1 retries updated: {new_retries}"

[gcode_macro _CLEAR_PRIMARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T0 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_PRIMARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _CLEAR_SECONDARY_TOOLHEAD_RESULT]
gcode = 
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 result set"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=results VALUE="[]"
	DEBUG_ECHO PREFIX="Z Offset Testing" MSG="Clearing T1 retries"
	SET_GCODE_VARIABLE MACRO=_ADD_SECONDARY_TOOLHEAD_RESULT VARIABLE=retries VALUE=0

[gcode_macro _VAOC_TEST_Z_OFFSET]
gcode = 
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set act_t = 1 if idex_mode == 'primary' else 0 %}
	
	
	{% set z_offset_probe_x_offset = printer["z_offset_probe"].x_offset|default(0)|float %}
	{% set z_offset_probe_y_offset = printer["z_offset_probe"].y_offset|default(0)|float %}
	{% set speed = printer["gcode_macro RatOS"].toolchange_travel_speed * 60 %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set idex_xcontrolpoint = svv.idex_xcontrolpoint|default(150)|float %}
	{% set idex_ycontrolpoint = svv.idex_ycontrolpoint|default(30)|float %}
	{% set idex_zcontrolpoint = svv.idex_zcontrolpoint|default(50)|float %}
	
	
	G1 Z{idex_zcontrolpoint} F{z_speed}
	G1 X{idex_xcontrolpoint + z_offset_probe_x_offset} Y{idex_ycontrolpoint + z_offset_probe_y_offset} F{speed}
	
	
	_VAOC_Z_OFFSET_PROBE_CURRENT_POSITION
	G0 Z{idex_zcontrolpoint} F{z_speed}

[delayed_gcode _IDEX_INIT]
initial_duration = 0.5
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	VERIFY_HYBRID_INVERTED

[gcode_macro Z_TILT_ADJUST]
rename_existing = Z_TILT_ADJUST_ORIG
gcode = 
	
	{% set beacon_contact_z_tilt_adjust_samples = printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust_samples|default(2)|int %}
	{% set beacon_contact_z_tilt_adjust = true if printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(true)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	
	{% set idex_mode = printer["dual_carriage"].carriage_1|lower %}
	
	_IDEX_SINGLE
	
	_SELECT_TOOL T={printer["gcode_macro RatOS"].default_toolhead|default(0)|int} TOOLSHIFT=false
	{% endif %}
	
	
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	DEPLOY_PROBE
	{% endif %}
	{% if printer.fastconfig.settings.beacon is defined and beacon_contact_z_tilt_adjust %}
	Z_TILT_ADJUST_ORIG PROBE_METHOD=contact SAMPLES={beacon_contact_z_tilt_adjust_samples}
	{% else %}
	Z_TILT_ADJUST_ORIG
	{% endif %}
	{% if printer["gcode_macro RatOS"].z_probe == 'stowable' %}
	STOW_PROBE
	{% endif %}
	
	
	{% if printer["dual_carriage"] is defined %}
	{% if idex_mode == "copy" %}
	_IDEX_COPY
	{% elif idex_mode == "mirror" %}
	_IDEX_MIRROR
	{% endif %}
	{% endif %}

[stepper_x]
position_max = 500
position_endstop = -59.6
position_min = -59.6
step_pin = PF13
dir_pin = x_dir_pin
enable_pin = !PF14
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = toolboard_t0:PA2

[stepper_y]
position_max = 533.65
position_min = -14.35
position_endstop = -14.35
step_pin = PG0
dir_pin = !y_dir_pin
enable_pin = !PF15
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46
homing_speed = 50
endstop_pin = PG9

[stepper_z]
position_max = 500
position_min = -7
step_pin = PC13
dir_pin = !z0_dir_pin
enable_pin = !PF1
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4
homing_speed = 10
endstop_pin = probe:z_virtual_endstop

[z_tilt]
z_positions = 
	0,0
	250,500
	500,0
points = 
	20, 10
	480, 230
	20, 450
horizontal_move_z = 20
retries = 10
retry_tolerance = 0.02
speed = 600

[extruder]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t0:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t0:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t0:PD3
dir_pin = toolboard_t0:e_dir_pin
enable_pin = !toolboard_t0:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[firmware_retraction]
retract_speed = 60
unretract_extra_length = 0
unretract_speed = 60
retract_length = 0.2

[extruder1]
rotation_distance = 22.67895
gear_ratio = 50:8
microsteps = 64
max_extrude_only_distance = 300
max_extrude_only_velocity = 75.0
max_extrude_only_accel = 1500
filament_diameter = 1.750
nozzle_diameter = 0.4
heater_pin = toolboard_t1:PB0
sensor_type = PT1000
pullup_resistor = 2200
sensor_pin = toolboard_t1:PA1
min_extrude_temp = 170
min_temp = 0
max_temp = 485
pressure_advance = 0.008
step_pin = toolboard_t1:PD3
dir_pin = toolboard_t1:e_dir_pin
enable_pin = !toolboard_t1:PB6
full_steps_per_rotation = 200
control = pid
pid_kp = 28.413
pid_ki = 1.334
pid_kd = 151.300

[resonance_tester]
accel_chip_x = lis2dw toolboard_t0
accel_chip_y = lis2dw toolboard_t0
probe_points = 
	250,250,20

[tmc5160 stepper_x]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC4
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 dual_carriage]
stealthchop_threshold = 0
interpolate = True
cs_pin = PF2
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y]
stealthchop_threshold = 0
interpolate = True
cs_pin = PD11
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[tmc5160 stepper_y1]
stealthchop_threshold = 0
interpolate = True
cs_pin = PC7
spi_software_mosi_pin = PA7
spi_software_miso_pin = PA6
spi_software_sclk_pin = PA5
run_current = 1.6
sense_resistor = 0.075

[stepper_y1]
step_pin = PG4
dir_pin = y1_dir_pin
enable_pin = !PA2
microsteps = 32
full_steps_per_rotation = 400
rotation_distance = 46

[tmc2209 stepper_z]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE4
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[tmc2209 stepper_z1]
stealthchop_threshold = 0
interpolate = True
uart_pin = PE1
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z1]
step_pin = PE2
dir_pin = !z1_dir_pin
enable_pin = !PD4
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 stepper_z2]
stealthchop_threshold = 0
interpolate = True
uart_pin = PD3
run_current = 1.6
driver_tbl = 2
driver_toff = 3
driver_hend = 0
driver_hstrt = 6
sense_resistor = 0.11

[stepper_z2]
step_pin = PE6
dir_pin = !z2_dir_pin
enable_pin = !PE0
microsteps = 16
full_steps_per_rotation = 200
rotation_distance = 4

[tmc2209 extruder]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t0:PB3
run_current = 0.707
sense_resistor = 0.11

[tmc2209 extruder1]
stealthchop_threshold = 0
interpolate = False
uart_pin = toolboard_t1:PB3
run_current = 0.707
sense_resistor = 0.11

[beacon]
serial = /dev/beacon
x_offset = 0
y_offset = 27.5
mesh_main_direction = x
mesh_runs = 1
mesh_cluster_size = 0
speed = 15.
lift_speed = 80.
contact_max_hotend_temperature = 275
contact_mesh_min = 20,20
contact_mesh_max = 480,480

[beacon_user_z_offset]

[beacon_mesh]

[beacon_true_zero_correction]

[beacon_adaptive_heat_soak]

[delayed_gcode _BEACON_INIT]
initial_duration = 1
gcode = 
	ENSURE_CRITICAL_RATOS_INIT
	
	_BEACON_MESH_INIT
	
	
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_coefficient_multiplier
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=nozzle_expansion_applied_offset
	_INIT_HANDLE_DEPRECATED_SAVE_VARIABLES_VARIABLE VARIABLE=beacon_saved_runtime_offset
	{% if printer["gcode_macro RatOS"].beacon_contact_expansion_multiplier is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_contact_expansion_multiplier is no longer used, please remove it from your config file."
	{% endif %}
	{% if printer["gcode_macro RatOS"].beacon_scan_compensation_resolution is defined %}
	CONSOLE_ECHO TITLE="Deprecated gcode variable" TYPE="warning" MSG="The variable beacon_scan_compensation_resolution is no longer used, please remove it from your config file."
	{% endif %}

[gcode_macro BEACON_RATOS_CALIBRATION]
gcode = 
	RATOS_ECHO MSG="Did you mean BEACON_RATOS_CALIBRATE?"

[gcode_macro BEACON_RATOS_CALIBRATE]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	BEACON_INITIAL_CALIBRATION _AUTOMATED=True
	
	{% if beacon_contact_start_print_true_zero %}
	BEACON_POKE_TEST _AUTOMATED=True
	_BEACON_CHECK_POKE
	{% if printer["dual_carriage"] is not defined %}
	BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET _AUTOMATED=True
	{% endif %}
	{% endif %}
	
	{% set already_heated = False %}
	
	
	{% if beacon_contact_start_print_true_zero and beacon_scan_compensation_enable %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% set already_heated = True %}
	{% endif %}
	
	
	BEACON_FINAL_CALIBRATION _AUTOMATED=True _AUTOMATED_ALREADY_HEATED={already_heated} BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	{% if beacon_contact_start_print_true_zero %}
	{% if printer["dual_carriage"] is not defined %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	_BEACON_ECHO_POKE
	{% endif %}
	RATOS_ECHO MSG="Beacon calibration finished!"
	
	
	_LED_BEACON_CALIBRATION_END
	
	
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG

[gcode_macro BEACON_INITIAL_CALIBRATION]
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Initial beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro BEACON_FINAL_CALIBRATION]
description = Runs BEACON_AUTO_CALIBRATE after heating the bed and chamber to specified temperatures. This creates a beacon model under reference conditions for future use.
	This macro will skip calibration if both the beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero settings are enabled, because a new
	model will be calibrated automatically at the start of each print. Use FORCE=True to override this check.
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set already_heated = true if params._AUTOMATED_ALREADY_HEATED|default(false)|lower == 'true' else false %}
	{% set force = params.FORCE|default('false')|lower in ('1', 'true', 'yes') %}
	
	
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default('false')|lower == "true" %}
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero and not force %}
	RATOS_ECHO MSG="BEACON_FINAL_CALIBRATION skipped, not needed because beacon_contact_calibrate_model_on_true_zero is enabled. Use FORCE=True to override."
	{% else %}
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	{% set beacon_adaptive_heat_soak_layer_quality = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_layer_quality|default(3)|int %}
	{% set beacon_adaptive_heat_soak_maximum_first_layer_duration = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_maximum_first_layer_duration|default(1800)|int %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	{% if chamber_temp > 0 and not already_heated %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G90
	
	{% if not already_heated %}
	
	G0 Z2.5 F{z_hop_speed}
	
	
	RATOS_ECHO MSG="Waiting for calibration temperature..."
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	{% if beacon_adaptive_heat_soak %}
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,3600]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	{% endif %}
	
	
	_Z_HOP
	
	
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Final beacon contact calibration finished!"
	{% if not automated %}
	_CONSOLE_SAVE_CONFIG
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	{% endif %}

[gcode_macro BEACON_POKE_TEST]
variable_poke_result_1 = -1
variable_poke_result_2 = -1
variable_poke_result_3 = -1
variable_poke_result_4 = -1
variable_poke_result_5 = -1
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set z_hop_speed = printer.fastconfig.config.ratos_homing.z_hop_speed|float * 60 %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_1 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_2 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_3 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_4 VALUE=-1
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE=poke_result_5 VALUE=-1
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	G0 Z5 F{z_hop_speed}
	
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=1
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=2
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=3
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=4
	
	_BEACON_PROBE_POKE
	_BEACON_STORE_POKE I=5
	
	
	_Z_HOP
	
	
	RATOS_ECHO MSG="Beacon poke test finished!"
	{% if not automated %}
	_BEACON_ECHO_POKE
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}

[gcode_macro _BEACON_PROBE_POKE]
gcode = 
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	BEACON_POKE speed=3 top=5 bottom={poke_bottom}
	BEACON_QUERY

[gcode_macro _BEACON_STORE_POKE]
gcode = 
	
	{% set i = params.I|default(1)|int %}
	
	
	{% set last_z = printer.beacon.last_poke_result|default(0)|float %}
	
	
	{% if printer.beacon.last_poke_result|lower != "none" %}
	{% if printer.beacon.last_poke_result.error == 0 %}
	SET_GCODE_VARIABLE MACRO=BEACON_POKE_TEST VARIABLE={"poke_result_%s" % i} VALUE={printer.beacon.last_poke_result.latency}
	{% endif %}
	{% endif %}

[gcode_macro _BEACON_CHECK_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% if p1 == -1 or p2 == -1 or p3 == -1 or p4 == -1 or p5 == -1 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test error!") }
	{% endif %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	{% if avg > 6 %}
	_LED_BEACON_CALIBRATION_ERROR
	{ action_raise_error("Beacon poke test failed!") }
	{% endif %}

[gcode_macro _BEACON_ECHO_POKE]
gcode = 
	
	{% set p1 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_1|int %}
	{% set p2 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_2|int %}
	{% set p3 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_3|int %}
	{% set p4 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_4|int %}
	{% set p5 = printer["gcode_macro BEACON_POKE_TEST"].poke_result_5|int %}
	
	
	{% set avg = (p1 + p2 + p3 + p4 + p5) / 5 %}
	
	
	{% if avg <= 1 %}
	{% set type = "success" %}
	{% set note = "Extremely low noise, rarely achieved" %}
	{% elif avg > 1 and avg <= 4 %}
	{% set type = "info" %}
	{% set note = "Excellent performance for a typical printer" %}
	{% elif avg > 4 and avg <= 8 %}
	{% set type = "warning" %}
	{% set note = "Acceptable performance, machine may have considerable cyclic axis noise" %}
	{% elif avg > 8 and avg <= 11 %}
	{% set type = "alert" %}
	{% set note = "Not ideal, may want to verify proper mounting or use thinner stackups" %}
	{% elif avg > 11 %}
	{% set type = "alert" %}
	{% set note = "Reason for concern, present setup may be risky to continue with" %}
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon poke test result:" TYPE={type} MSG={'"Average latency: %.2f_N_%s"' % (avg, note)}

[gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET]
variable_reference_z = 0.0
gcode = 
	
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Nozzle temperature offset calibration..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=150
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=150
	
	
	_BEACON_PROBE_NOZZLE_TEMP_OFFSET TEMP=250
	_BEACON_STORE_NOZZLE_TEMP_OFFSET TEMP=250
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET=0
	
	
	{% if not automated %}
	_BEACON_ECHO_NOZZLE_TEMP_OFFSETS
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_PROBE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Waiting for nozzle to reach {temp}°C..."
	SET_HEATER_TEMPERATURE HEATER={"extruder" if default_toolhead == 0 else "extruder1"} TARGET={temp}
	TEMPERATURE_WAIT SENSOR={"extruder" if default_toolhead == 0 else "extruder1"} MINIMUM={temp} MAXIMUM={temp + 2}
	
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing with nozzle temperature {temp}°C..."
	PROBE PROBE_METHOD=contact PROBE_SPEED=3 LIFT_SPEED=15 SAMPLES=5 SAMPLE_RETRACT_DIST=3 SAMPLES_TOLERANCE=0.005 SAMPLES_TOLERANCE_RETRIES=10 SAMPLES_RESULT=median
	BEACON_QUERY
	
	
	G0 Z5 F{z_speed}

[gcode_macro _BEACON_STORE_NOZZLE_TEMP_OFFSET]
gcode = 
	
	{% set temp = params.TEMP|int %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set last_z = printer.beacon.last_z_result|default(0)|float %}
	
	
	{% if temp == 150 %}
	SET_GCODE_VARIABLE MACRO=BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_CALIBRATE_NOZZLE_TEMP_OFFSET"].reference_z|default(0)|float %}
	SAVE_VARIABLE VARIABLE=nozzle_expansion_coefficient_t{default_toolhead} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_NOZZLE_TEMP_OFFSETS]
gcode = 
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% if default_toolhead == 0 %}
	CONSOLE_ECHO TYPE="info" MSG={'"T0 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t0}
	{% else %}
	CONSOLE_ECHO TYPE="info" MSG={'"T1 expansion coefficient %.6f"' % svv.nozzle_expansion_coefficient_t1}
	{% endif %}

[gcode_macro _BEACON_SET_NOZZLE_TEMP_OFFSET]
description = "Set the thermal expansion z offset for the active toolhead based on the current extruder target temperature and thermal expansion coefficient."
gcode = 
	{% if params.RESET is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The RESET parameter is no longer supported and has no effect."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% if params.TOOLHEAD is defined %}
	CONSOLE_ECHO TITLE="Deprecated parameter" TYPE="warning" MSG="The TOOLHEAD parameter is no longer supported and has no effect. The macro now automatically determines the current toolhead."
	_DEBUG_ECHO_STACK_TRACE
	{% endif %}
	
	{% set beacon_contact_expansion_compensation = true if printer["gcode_macro RatOS"].beacon_contact_expansion_compensation|default(false)|lower == 'true' else false %}
	{% if beacon_contact_expansion_compensation %}
	
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_contact_true_zero_temp = printer["gcode_macro RatOS"].beacon_contact_true_zero_temp|default(150)|int %}
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set toolhead = default_toolhead %}
	{% if printer["dual_carriage"] is defined %}
	
	{% set current_idex_mode = printer["dual_carriage"].carriage_1|lower %}
	{% set toolhead = 1 if current_idex_mode=='primary' else default_toolhead %}
	{% endif %}
	
	
	{% set svv = printer.save_variables.variables %}
	
	
	{% set nozzle_expansion_coefficient_t0 = svv.nozzle_expansion_coefficient_t0|default(0)|float %}
	{% if printer["dual_carriage"] is defined %}
	{% set nozzle_expansion_coefficient_t1 = svv.nozzle_expansion_coefficient_t1|default(0)|float %}
	{% endif %}
	
	
	{% set temp = printer['extruder' if toolhead == 0 else 'extruder1'].target|float %}
	
	
	{% set temp_delta = temp - beacon_contact_true_zero_temp %}
	{% set expansion_coefficient = nozzle_expansion_coefficient_t0 if toolhead == 0 else nozzle_expansion_coefficient_t1 %}
	{% set expansion_offset = temp_delta * (expansion_coefficient / 100) %}
	
	
	SET_NAMED_OFFSET NAME=hotend_thermal_expansion Z={expansion_offset} MOVE=1 MOVE_SPEED={z_speed}
	
	
	RATOS_ECHO PREFIX="BEACON" MSG={'"Nozzle expansion offset of %.6fmm applied to T%s"' % (expansion_offset, toolhead)}
	DEBUG_ECHO PREFIX="_BEACON_SET_NOZZLE_TEMP_OFFSET" MSG="toolhead: {toolhead}, coefficient: {expansion_coefficient|round(6)}, temp_delta: {temp_delta|round(1)},  expansion_offset: {expansion_offset|round(6)}"
	
	{% endif %}

[gcode_macro BEACON_MEASURE_BEACON_OFFSET]
variable_needs_compensation = False
variable_reference_z = 0.0
variable_front = 0.0
variable_front_left = 0.0
variable_front_right = 0.0
variable_back = 0.0
variable_back_left = 0.0
variable_back_right = 0.0
variable_right = 0.0
variable_left = 0.0
variable_margin_x = 40
variable_margin_y = 40
gcode = 
	
	{% set speed = printer["gcode_macro RatOS"].macro_travel_speed|float * 60 %}
	{% set printable_x_max = printer["gcode_macro RatOS"].printable_x_max|float %}
	{% set printable_y_max = printer["gcode_macro RatOS"].printable_y_max|float %}
	{% set safe_home_x, safe_home_y = printer.ratos.safe_home_position %}
	{% set poke_bottom = printer["gcode_macro RatOS"].beacon_contact_poke_bottom_limit|default(-1)|float %}
	
	
	{% set beacon_contact_start_print_true_zero = true if printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' else false %}
	
	{% if beacon_contact_start_print_true_zero %}
	
	
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=False
	
	
	_BEACON_HOME_AND_ABL
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	RATOS_ECHO PREFIX="BEACON" MSG="Measure beacon offset..."
	
	
	{% for i in range(10) %}
	beacon_poke speed=3 top=5 bottom={poke_bottom}
	{% endfor %}
	
	
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="center"
	
	
	G0 X{margin_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_left"
	
	
	G0 X{safe_home_x} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front"
	
	
	G0 X{(printable_x_max - margin_x)} Y{margin_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="front_right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="right"
	
	
	G0 X{(printable_x_max - margin_x)} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_right"
	
	
	G0 X{safe_home_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back"
	
	
	G0 X{margin_x} Y{(printable_y_max - margin_y)} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="back_left"
	
	
	G0 X{margin_x} Y{safe_home_y} F{speed}
	_BEACON_OFFSET_COMPARE
	_BEACON_STORE_BEACON_OFFSET LOCATION="left"
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_BEACON_ECHO_BEACON_OFFSET
	
	
	_LED_BEACON_CALIBRATION_END
	
	{% endif %}

[gcode_macro _BEACON_STORE_BEACON_OFFSET]
gcode = 
	
	{% set location = params.LOCATION|lower %}
	
	
	{% set last_z = printer.beacon.last_offset_result["delta"]|default(0)|float %}
	
	
	{% if location == "center" %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=reference_z VALUE={last_z}
	{% else %}
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE={location} VALUE={(last_z - reference_z)}
	{% endif %}

[gcode_macro _BEACON_ECHO_BEACON_OFFSET]
gcode = 
	
	{% set reference_z = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].reference_z|default(0)|float * 1000 %}
	{% set front_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_left|default(0)|float * 1000 %}
	{% set front = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front|default(0)|float * 1000 %}
	{% set front_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].front_right|default(0)|float * 1000 %}
	{% set right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].right|default(0)|float * 1000 %}
	{% set back_right = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_right|default(0)|float * 1000 %}
	{% set back = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back|default(0)|float * 1000 %}
	{% set back_left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].back_left|default(0)|float * 1000 %}
	{% set left = printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].left|default(0)|float * 1000 %}
	
	{% set line_1 = "Front left:    %.6fμm" % (front_left) %}
	{% set line_2 = "Front center:  %.6fμm" % (front) %}
	{% set line_3 = "Front right:   %.6fμm" % (front_right) %}
	{% set line_4 = "Left center:   %.6fμm" % (left) %}
	{% set line_5 = "Right center:  %.6fμm" % (right) %}
	{% set line_6 = "Back left:     %.6fμm" % (back_left) %}
	{% set line_7 = "Back center:   %.6fμm" % (back) %}
	{% set line_8 = "Back right:    %.6fμm" % (back_right) %}
	
	{% set max_value = [(front_left|abs), (front|abs), (front_right|abs), (left|abs), (right|abs), (back_left|abs), (back|abs), (back_right|abs)]|max %}
	{% if max_value <= 50 %}
	{% set type = "success" %}
	{% set recommendation = "Very low beacon offset: %.6fμm._N_No beacon scan compensation needed." % max_value %}
	{% elif max_value > 50 and max_value <= 100 %}
	{% set type = "info" %}
	{% set recommendation = "Low beacon offset: %.6fμm._N_You may experience first layer inconsistensies, consider beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 100 and max_value <= 150 %}
	{% set type = "warning" %}
	{% set recommendation = "High beacon offset: %.6fμm._N_High chance of first layer problems, beacon scan compensation is highly encouraged." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 150 and max_value <= 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Very High beacon offset: %.6fμm._N_You will encounter first layer problems on large prints unless you activate beacon scan compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% elif max_value > 200 %}
	{% set type = "alert" %}
	{% set recommendation = "Extremely high beacon offset: %.6fμm._N_You have significant scan/contact inconsistency which is indicative of mechanical problems, please investigate before resorting to software compensation." % max_value %}
	SET_GCODE_VARIABLE MACRO=BEACON_MEASURE_BEACON_OFFSET VARIABLE=needs_compensation VALUE=True
	{% endif %}
	
	
	CONSOLE_ECHO TITLE="Beacon offset relative to the center" TYPE={type} MSG={'"_N_%s_N__N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s_N_%s"' % (recommendation, line_1, line_2, line_3, line_4, line_5, line_6, line_7, line_8)}

[gcode_macro BEACON_CREATE_SCAN_COMPENSATION_MESH]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	{% set profile = params.PROFILE|default("auto")|string %}
	{% set automated = true if params._AUTOMATED|default(false)|lower == 'true' else false %}
	{% set keep_temp_meshes = params.KEEP_TEMP_MESHES|default(0) %}
	
	
	{% set default_toolhead = printer["gcode_macro RatOS"].default_toolhead|default(0)|int %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default(false)|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = printer["gcode_macro RatOS"].beacon_contact_calibrate_model_on_true_zero|default(false)|lower == 'true' %}
	{% set desired_spacing = printer["gcode_macro RatOS"].beacon_scan_compensation_desired_spacing|float %}
	{% set bed_heat_soak_time = printer["gcode_macro RatOS"].bed_heat_soak_time|default(0)|int %}
	{% set hotend_heat_soak_time = printer["gcode_macro RatOS"].hotend_heat_soak_time|default(0)|int %}
	{% set z_speed = printer["gcode_macro RatOS"].macro_z_speed|float * 60 %}
	
	
	{% set beacon_adaptive_heat_soak = true if printer["gcode_macro RatOS"].beacon_adaptive_heat_soak|default(false)|lower == 'true' else false %}
	{% set beacon_adaptive_heat_soak_min_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_min_wait|default(0)|int %}
	{% set beacon_adaptive_heat_soak_max_wait = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_max_wait|default(5400)|int %}
	{% set beacon_adaptive_heat_soak_extra_wait_after_completion = printer["gcode_macro RatOS"].beacon_adaptive_heat_soak_extra_wait_after_completion|default(0)|int %}
	
	{% if not beacon_scan_compensation_enable %}
	RATOS_ECHO MSG="Beacon scan compensation is disabled!"
	
	{% else %}
	
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	_LED_BEACON_CALIBRATION_START
	
	
	{% if chamber_temp > 0 %}
	_CHAMBER_HEATER_ON CHAMBER_TEMP={chamber_temp}
	{% endif %}
	
	
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=150
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET={bed_temp}
	
	
	RATOS_ECHO MSG="Please wait..."
	TEMPERATURE_WAIT SENSOR=heater_bed MINIMUM={bed_temp} MAXIMUM={(bed_temp + 5)}
	TEMPERATURE_WAIT SENSOR={'extruder' if default_toolhead == 0 else 'extruder1'} MINIMUM=150 MAXIMUM=155
	
	
	
	{% if beacon_contact_start_print_true_zero and beacon_contact_calibrate_model_on_true_zero %}
	BEACON_AUTO_CALIBRATE SKIP_MULTIPOINT_PROBING=1
	{% else %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME
	
	
	G1 Z2.5 F{z_speed}
	{% if beacon_adaptive_heat_soak %}
	
	
	BEACON_WAIT_FOR_PRINTER_HEAT_SOAK _FORCE_THRESHOLD=100 MINIMUM_WAIT={beacon_adaptive_heat_soak_min_wait} MAXIMUM_WAIT={[beacon_adaptive_heat_soak_max_wait,9000]|max}
	{% if beacon_adaptive_heat_soak_extra_wait_after_completion > 0 %}
	RATOS_ECHO MSG="Waiting for an additional {beacon_adaptive_heat_soak_extra_wait_after_completion} seconds after heat soak completion..."
	G4 P{(beacon_adaptive_heat_soak_extra_wait_after_completion * 1000)}
	{% endif %}
	{% else %}
	{% if bed_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking bed for {bed_heat_soak_time} seconds..."
	G4 P{(bed_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if not (beacon_adaptive_heat_soak or bed_heat_soak_time > 0) %}
	
	{% if hotend_heat_soak_time > 0 %}
	RATOS_ECHO MSG="Heat soaking hotend for {hotend_heat_soak_time} seconds..."
	G4 P{(hotend_heat_soak_time * 1000)}
	{% endif %}
	{% endif %}
	
	
	{% if printer.z_tilt is defined %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% endif %}
	{% if printer.quad_gantry_level is defined %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% endif %}
	
	
	_BEACON_CREATE_SCAN_COMPENSATION_MESH_CORE PROFILE="{profile}" DESIRED_SPACING={desired_spacing} CHAMBER_TEMP={chamber_temp} KEEP_TEMP_MESHES={keep_temp_meshes}
	
	
	{% if not automated %}
	SET_HEATER_TEMPERATURE HEATER={'extruder' if default_toolhead == 0 else 'extruder1'} TARGET=0
	SET_HEATER_TEMPERATURE HEATER=heater_bed TARGET=0
	{% endif %}
	
	
	{% if chamber_temp > 0 and not automated %}
	_CHAMBER_HEATER_OFF
	{% endif %}
	
	{% if automated %}
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}
	
	
	{% if not automated %}
	_LED_BEACON_CALIBRATION_END
	{% endif %}
	
	
	RATOS_ECHO MSG="Beacon scan compensation mesh created!"
	
	
	{% if not automated %}
	RATOS_ECHO MSG="Saving config and restarting klipper..."
	SAVE_CONFIG
	{% endif %}
	
	{% endif %}

[gcode_macro _BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED]
gcode = 
	
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	
	DEBUG_ECHO PREFIX="_BEACON_APPLY_SCAN_COMPENSATION_IF_ENABLED" MSG="beacon_scan_compensation_profile {beacon_scan_compensation_profile}, beacon_scan_compensation_enable {beacon_scan_compensation_enable}"
	
	{% if beacon_scan_compensation_enable %}
	BEACON_APPLY_SCAN_COMPENSATION PROFILE="{beacon_scan_compensation_profile}"
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_MODEL]
gcode = 
	
	{% set beacon_contact_start_print_true_zero = params.BEACON_CONTACT_START_PRINT_TRUE_ZERO|lower == 'true' %}
	{% set beacon_contact_calibrate_model_on_true_zero = params.beacon_contact_calibrate_model_on_true_zero|lower == 'true' %}
	
	
	{% if printer.fastconfig.settings.beacon is defined and not printer.beacon.model %}
	{% set beacon_model_required_for_true_zero = beacon_contact_start_print_true_zero and not beacon_contact_calibrate_model_on_true_zero %}
	{% set beacon_model_required_for_homing =
	printer.fastconfig.settings.stepper_z.endstop_pin == 'probe:z_virtual_endstop'
	and (( printer.fastconfig.settings.beacon.home_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_homing|default(false)|lower != 'true')
	or ( printer.fastconfig.settings.beacon.default_probe_method|default('proximity')|lower == 'proximity'
	and printer["gcode_macro RatOS"].beacon_contact_z_tilt_adjust|default(false)|lower != 'true' )) %}
	{% if beacon_model_required_for_homing or beacon_model_required_for_true_zero %}
	_LED_START_PRINTING_ERROR
	{ action_raise_error("An active Beacon model is required. Have you performed initial Beacon calibration?") }
	{% endif %}
	{% endif %}

[gcode_macro _START_PRINT_PREFLIGHT_CHECK_BEACON_SCAN_COMPENSATION]
gcode = 
	{% set beacon_scan_compensation_profile = printer["gcode_macro RatOS"].beacon_scan_compensation_profile %}
	{% set beacon_scan_compensation_enable = true if printer["gcode_macro RatOS"].beacon_scan_compensation_enable|default(false)|lower == 'true' else false %}
	{% set bed_temp_mismatch_is_error = true if printer["gcode_macro RatOS"].beacon_scan_compensation_bed_temp_mismatch_is_error|default(false)|lower == 'true' else false %}
	
	{% set bed_temp = params.BED_TEMP|default(0)|float %}
	{% if bed_temp == 0 %}
	{% set bed_temp = printer.heater_bed.temperature %}
	{% endif %}
	
	DEBUG_ECHO PREFIX="_START_PRINT_PREFLIGHT_CHECK_BEACON" MSG="beacon_scan_compensation_profile={beacon_scan_compensation_profile}, beacon_scan_compensation_enable={beacon_scan_compensation_enable}, bed_temp={bed_temp}"
	
	{% if beacon_scan_compensation_enable %}
	_VALIDATE_COMPENSATION_MESH_PROFILE PROFILE="{beacon_scan_compensation_profile}" TITLE="Check Beacon scan compensation profile" SUBJECT="Configured compensation profile '{beacon_scan_compensation_profile}'" COMPARE_BED_TEMP={bed_temp} COMPARE_BED_TEMP_IS_ERROR={bed_temp_mismatch_is_error}
	{% endif %}

[gcode_macro _BEACON_MAYBE_SCAN_COMPENSATION]
gcode = 
	
	{% set bed_temp = params.BED_TEMP|default(85)|int %}
	{% set chamber_temp = params.CHAMBER_TEMP|default(0)|int %}
	
	
	{% set needs_scan_compensation = true if printer["gcode_macro BEACON_MEASURE_BEACON_OFFSET"].needs_compensation|default(false)|lower == 'true' else false %}
	
	{% if needs_scan_compensation %}
	BEACON_CREATE_SCAN_COMPENSATION_MESH _AUTOMATED=True BED_TEMP={bed_temp} CHAMBER_TEMP={chamber_temp}
	{% endif %}

[gcode_macro _BEACON_HOME_AND_ABL]
gcode = 
	
	{% if printer["dual_carriage"] is defined %}
	_IDEX_SINGLE INIT=1
	{% endif %}
	
	
	MAYBE_HOME X=True Y=True
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	
	
	{% set needs_rehoming = False %}
	{% if printer.z_tilt is defined and not printer.z_tilt.applied %}
	RATOS_ECHO MSG="Adjusting Z tilt..."
	Z_TILT_ADJUST
	RATOS_ECHO MSG="Rehoming Z after Z tilt adjustment..."
	{% set needs_rehoming = True %}
	{% endif %}
	{% if printer.quad_gantry_level is defined and not printer.quad_gantry_level.applied %}
	RATOS_ECHO MSG="Running quad gantry leveling..."
	QUAD_GANTRY_LEVEL
	RATOS_ECHO MSG="Rehoming Z after quad gantry leveling..."
	{% set needs_rehoming = True %}
	{% endif %}
	
	
	_MOVE_TO_SAFE_Z_HOME Z_HOP=True
	
	
	{% if needs_rehoming %}
	BEACON_AUTO_CALIBRATE SKIP_MODEL_CREATION=1 SKIP_MULTIPOINT_PROBING=1
	{% endif %}

[gcode_macro SAVE_Z_OFFSET]
description = Deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead, or in Mainsail use the SAVE button in the Z-OFFSET section.
gcode = 
	{% set beacon_contact_start_print_true_zero = printer["gcode_macro RatOS"].beacon_contact_start_print_true_zero|default('false')|lower == 'true' %}
	{% set msg = "SAVE_Z_OFFSET is deprecated. Use the Klipper standard Z_OFFSET_APPLY_PROBE macro instead,_N_or in Mainsail use the SAVE button in the Z-OFFSET section."%}
	{% if not (printer.fastconfig.settings.beacon is defined and beacon_contact_start_print_true_zero) %}
	{% set msg = msg + "_N_You must then use the SAVE_CONFIG command to persist the change." %}
	{% endif %}
	CONSOLE_ECHO TYPE="error" MSG="{msg}"

[gcode_macro _BEACON_OFFSET_COMPARE]
gcode = 
	
	RATOS_ECHO PREFIX="BEACON" MSG="Probing..."
	
	
	BEACON_OFFSET_COMPARE SAMPLES_DROP=1 SAMPLES=3
	BEACON_QUERY

[fan]
pin = rpi:gpio4

[fan_generic part_fan_t0]
pin = PA8
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[fan_generic part_fan_t1]
pin = PE5
max_power = 0.8
shutdown_speed = 0
cycle_time = 0.005
hardware_pwm = False
kick_start_time = 0.100
off_below = 0.1

[heater_fan toolhead_cooling_fan_t0]
heater = extruder
shutdown_speed = 1
pin = toolboard_t0:PB4

[heater_fan toolhead_cooling_fan_t1]
heater = extruder1
shutdown_speed = 1
pin = toolboard_t1:PB4

[controller_fan controller_fan]
pin = dinghy:PA4
tachometer_pin = dinghy:PC15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[z_offset_probe]
pin = ^PG10
z_offset = -7
y_offset = 0
x_offset = 37.5
speed = 10
samples = 3
sample_retract_dist = 5
lift_speed = 10.0
samples_result = median
samples_tolerance = 0.2
samples_tolerance_retries = 5

[neopixel vaoc_led]
pin = PB10
chain_count = 6
color_order = GRB

[heater_fan vaoc_fan]
pin = PD13
heater = heater_bed
fan_speed = 1.0
heater_temp = 50

[fan_generic filter]
pin = !PD14
enable_pin = PD15

[gcode_macro T0]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = True
variable_color = "7bff33"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = -32.6
variable_parking_position = -57.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=0 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[gcode_macro T1]
variable_join = 0
variable_remap = 0
variable_alert = ""
variable_filament_name = ""
variable_filament_type = ""
variable_filament_temp = 0
variable_runout_sensor = ""
variable_active = False
variable_color = "0ea5e9"
variable_hotend_type = "UHF"
variable_has_cht_nozzle = True
variable_cooling_position_to_nozzle_distance = 40
variable_tooolhead_sensor_to_extruder_gear_distance = 15
variable_extruder_gear_to_cooling_position_distance = 30
variable_filament_loading_nozzle_offset = -5
variable_filament_grabbing_length = 5
variable_filament_grabbing_speed = 1
variable_enable_insert_detection = True
variable_enable_runout_detection = True
variable_enable_clog_detection = True
variable_unload_after_runout = True
variable_purge_after_load = 0
variable_purge_before_unload = 0
variable_extruder_load_speed = 60
variable_filament_load_speed = 10
variable_standby = False
variable_temperature_offset = 0
variable_has_oozeguard = True
variable_has_front_arm_nozzle_wiper = False
variable_toolhead_sensor_button_only_when_sensor_enabled = False
variable_toolhead_detect_clog_only_when_sensor_enabled = True
variable_loading_position = 532.6
variable_parking_position = 557.6
variable_resume_after_insert = True
gcode = 
	{% set x = params.X|default(-1.0)|float %}
	{% set y = params.Y|default(-1.0)|float %}
	{% set z = params.Z|default(0.0)|float %}
	{% set s = params.S|default(1)|int %}
	{% if printer["gcode_macro _SELECT_TOOL"] is defined %}
	_SELECT_TOOL T=1 X={x} Y={y} Z={z} TOOLSHIFT={s}
	{% endif %}

[save_variables]
filename = /home/pi/printer_data/config/ratos-variables.cfg

[mcu dinghy]
serial = /dev/serial/by-id/usb-Klipper_stm32f072xb_Dragon_dinghy-if00

[temperature_sensor th0]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA0

[temperature_sensor th1]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA1

[temperature_sensor th2]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA2

[temperature_sensor th3]
sensor_type = Generic 3950
pullup_resistor = 2200
sensor_pin = dinghy:PA3

[controller_fan CTL2]
pin = dinghy:PB14
tachometer_pin = dinghy:PB15
tachometer_ppr = 2
tachometer_poll_interval = 0.001
cycle_time = 0.00004
hardware_pwm = true

[mcu plasma]
serial = /dev/serial/by-id/usb-Klipper_rp2040_Plasma-if00

[neopixel Chamber_Lights]
pin = plasma:gpio15
chain_count = 140
color_order = GRBW
initial_red = 0.0
initial_green = 0.0
initial_blue = 0.0
initial_white = 0.1

[beacon model default]
model_coef = 1.5287863993594841,
	1.9289099639750602,
	0.8838828622507556,
	0.25554883784260735,
	-0.015171504024913506,
	0.3044946127013882,
	0.15820427856566457,
	-0.25262403959326246,
	0.042488512846660914,
	0.16662470122520964
model_domain = 1.842634574664148e-07,1.9339206373083917e-07
model_range = 0.200000,5.000000
model_temp = 13.222247
model_offset = 0.00000

[bed_mesh default]
version = 1
points = 
	0.016163, 0.016713, 0.001923, -0.017658, -0.031574, -0.032498, -0.030898, -0.032177, -0.035213, -0.031148, -0.021322, -0.016924, -0.015012, -0.013911, -0.012197, -0.012583, -0.010489, -0.007529, -0.003986, -0.000980, 0.005518, 0.014442, 0.027426, 0.034677, 0.037410, 0.040391, 0.041842, 0.040369, 0.037615, 0.030776, 0.027664, 0.022856, 0.016892, 0.015398, 0.014717, 0.006921, 0.001532, 0.000731, 0.008657, 0.014036
	0.005356, -0.005066, -0.016998, -0.029668, -0.038334, -0.043672, -0.041139, -0.042488, -0.045199, -0.039432, -0.028746, -0.023642, -0.024058, -0.022802, -0.019679, -0.018514, -0.018102, -0.016476, -0.012722, -0.010077, -0.001809, 0.007180, 0.019853, 0.027754, 0.029964, 0.033626, 0.036783, 0.032018, 0.029372, 0.020847, 0.017634, 0.011926, 0.009013, 0.009254, 0.007972, -0.001380, -0.006940, -0.002160, 0.006135, 0.008330
	-0.004900, -0.006720, -0.021914, -0.039691, -0.050459, -0.050377, -0.046281, -0.048755, -0.054708, -0.051499, -0.033927, -0.027632, -0.030243, -0.031447, -0.024387, -0.021408, -0.020382, -0.018068, -0.015930, -0.013877, -0.006099, 0.003479, 0.013310, 0.024783, 0.025522, 0.030849, 0.033573, 0.031409, 0.025495, 0.016683, 0.011264, 0.008805, 0.006856, 0.008059, 0.007305, 0.002581, -0.003320, -0.003239, 0.004691, 0.010045
	-0.008791, -0.019334, -0.029149, -0.040533, -0.051698, -0.058235, -0.054863, -0.054840, -0.055692, -0.049534, -0.036731, -0.033053, -0.035667, -0.035315, -0.024352, -0.023825, -0.022538, -0.020438, -0.018207, -0.015389, -0.006515, 0.001966, 0.013591, 0.019434, 0.020600, 0.024967, 0.029425, 0.026812, 0.018980, 0.007878, 0.002360, 0.000859, 0.003849, 0.005649, 0.005421, -0.000416, -0.007906, -0.003164, 0.007582, 0.010039
	-0.018512, -0.018210, -0.033932, -0.050501, -0.061588, -0.064139, -0.060236, -0.062528, -0.067065, -0.062039, -0.045815, -0.039448, -0.040521, -0.042080, -0.033870, -0.030878, -0.027396, -0.024548, -0.021298, -0.020041, -0.011880, -0.002847, 0.008689, 0.015857, 0.015934, 0.018697, 0.022439, 0.022106, 0.017916, 0.005879, 0.001037, -0.001311, -0.001335, 0.001897, 0.003656, 0.000561, -0.006084, -0.005683, 0.000338, 0.006245
	-0.028558, -0.036721, -0.044680, -0.054969, -0.066140, -0.075045, -0.073515, -0.073161, -0.075696, -0.068963, -0.058892, -0.053111, -0.050990, -0.048040, -0.041262, -0.037419, -0.034866, -0.031845, -0.029787, -0.026524, -0.017896, -0.009322, -0.001010, 0.005819, 0.008058, 0.010456, 0.013266, 0.012529, 0.007992, -0.001491, -0.006769, -0.009303, -0.005980, -0.003567, -0.003340, -0.011496, -0.018818, -0.014808, -0.004181, -0.000733
	-0.037253, -0.038393, -0.053129, -0.066170, -0.075959, -0.079233, -0.077475, -0.082688, -0.086779, -0.083983, -0.069005, -0.062542, -0.060351, -0.058481, -0.051101, -0.043149, -0.039837, -0.037039, -0.034698, -0.031301, -0.024330, -0.019786, -0.010285, -0.001967, 0.002812, 0.004899, 0.009657, 0.006946, 0.002155, -0.005232, -0.009851, -0.011218, -0.011509, -0.010097, -0.010293, -0.013175, -0.018958, -0.019846, -0.012107, -0.005641
	-0.046584, -0.055590, -0.062606, -0.069218, -0.080399, -0.087414, -0.089037, -0.092376, -0.095115, -0.088957, -0.080802, -0.073290, -0.068741, -0.064591, -0.054452, -0.048270, -0.045916, -0.044559, -0.042047, -0.039605, -0.032667, -0.025789, -0.019495, -0.012773, -0.006697, -0.003025, 0.001413, 0.000817, -0.004738, -0.013008, -0.017605, -0.018191, -0.018524, -0.016356, -0.016750, -0.021992, -0.028943, -0.025791, -0.016146, -0.010447
	-0.051029, -0.051677, -0.068218, -0.079622, -0.088590, -0.089331, -0.089731, -0.096072, -0.105329, -0.100771, -0.087584, -0.079320, -0.075489, -0.072081, -0.064183, -0.054662, -0.048601, -0.049465, -0.047050, -0.045011, -0.040009, -0.032508, -0.025212, -0.018144, -0.011996, -0.008136, -0.003187, -0.003214, -0.006646, -0.013044, -0.019446, -0.020615, -0.022270, -0.021298, -0.020215, -0.020946, -0.026034, -0.026598, -0.021025, -0.012328
	-0.057184, -0.064908, -0.073093, -0.081584, -0.091971, -0.097048, -0.097688, -0.101869, -0.106651, -0.102162, -0.095658, -0.087938, -0.082718, -0.077017, -0.069608, -0.060682, -0.056889, -0.056864, -0.054260, -0.052011, -0.044563, -0.038927, -0.031943, -0.025832, -0.021170, -0.014319, -0.009046, -0.008543, -0.011751, -0.020287, -0.026608, -0.027259, -0.029120, -0.025549, -0.023221, -0.027725, -0.032477, -0.028427, -0.019343, -0.014932
	-0.060411, -0.062241, -0.080781, -0.090744, -0.100903, -0.099702, -0.098468, -0.104236, -0.116853, -0.112701, -0.102623, -0.095036, -0.091407, -0.089871, -0.079701, -0.070222, -0.064325, -0.063875, -0.062248, -0.059396, -0.052699, -0.047589, -0.041526, -0.028442, -0.024526, -0.019549, -0.015403, -0.014251, -0.017989, -0.022824, -0.027328, -0.029155, -0.033315, -0.032426, -0.027619, -0.030776, -0.033688, -0.032458, -0.027219, -0.019649
	-0.067541, -0.076514, -0.082321, -0.088656, -0.099968, -0.104930, -0.105875, -0.109051, -0.115531, -0.112996, -0.105760, -0.100390, -0.096171, -0.090011, -0.080050, -0.073632, -0.067451, -0.067031, -0.065225, -0.062471, -0.056370, -0.050129, -0.041626, -0.030801, -0.027579, -0.022472, -0.014826, -0.015306, -0.020316, -0.025953, -0.030661, -0.034103, -0.035502, -0.032738, -0.031311, -0.037314, -0.041306, -0.035280, -0.027449, -0.020395
	-0.068162, -0.069269, -0.088235, -0.096809, -0.103385, -0.103271, -0.102507, -0.109535, -0.123412, -0.118580, -0.106622, -0.099580, -0.097644, -0.096978, -0.087259, -0.077196, -0.068978, -0.067016, -0.063682, -0.062548, -0.057901, -0.052295, -0.044088, -0.032703, -0.026551, -0.021607, -0.014155, -0.013747, -0.017390, -0.022419, -0.027444, -0.030877, -0.033450, -0.032423, -0.032041, -0.033598, -0.035149, -0.034054, -0.029356, -0.020998
	-0.069473, -0.075924, -0.083569, -0.089648, -0.101235, -0.105828, -0.109144, -0.112613, -0.117233, -0.114186, -0.107090, -0.098616, -0.097084, -0.094257, -0.086773, -0.076409, -0.069532, -0.066472, -0.060956, -0.059191, -0.052886, -0.047752, -0.041275, -0.032437, -0.027780, -0.020398, -0.012061, -0.010133, -0.014056, -0.021528, -0.027924, -0.030605, -0.030609, -0.026068, -0.029346, -0.033991, -0.038254, -0.030610, -0.021109, -0.015885
	-0.068084, -0.066409, -0.083944, -0.094013, -0.102504, -0.105274, -0.106036, -0.112090, -0.121664, -0.117824, -0.104850, -0.097467, -0.098833, -0.098622, -0.089603, -0.078147, -0.068143, -0.066300, -0.061573, -0.057727, -0.054825, -0.048625, -0.040164, -0.030532, -0.025948, -0.020264, -0.014196, -0.010702, -0.013794, -0.019775, -0.026095, -0.028838, -0.030254, -0.027944, -0.027980, -0.030915, -0.032446, -0.028861, -0.023732, -0.014676
	-0.065280, -0.068669, -0.076948, -0.082397, -0.094986, -0.105117, -0.107099, -0.108954, -0.112557, -0.110326, -0.100725, -0.096325, -0.096240, -0.092388, -0.081185, -0.071682, -0.065650, -0.062250, -0.057027, -0.054691, -0.048349, -0.042069, -0.032712, -0.027728, -0.023396, -0.018458, -0.008357, -0.005699, -0.011447, -0.020033, -0.026387, -0.030280, -0.028443, -0.023735, -0.023838, -0.031580, -0.034204, -0.027768, -0.018029, -0.010628
	-0.061662, -0.057052, -0.075163, -0.086710, -0.094182, -0.097544, -0.098814, -0.105908, -0.114460, -0.111718, -0.097559, -0.091614, -0.093860, -0.093098, -0.081687, -0.069410, -0.064117, -0.062745, -0.055603, -0.051413, -0.048043, -0.040363, -0.031842, -0.023420, -0.017470, -0.012600, -0.008163, -0.003898, -0.007635, -0.013254, -0.019807, -0.025153, -0.027074, -0.023513, -0.023727, -0.028669, -0.029153, -0.024831, -0.018735, -0.009246
	-0.056176, -0.059439, -0.066501, -0.071527, -0.085216, -0.094918, -0.097595, -0.099419, -0.101847, -0.102015, -0.093849, -0.089867, -0.088840, -0.083167, -0.071832, -0.062522, -0.058023, -0.057771, -0.053050, -0.048285, -0.041374, -0.033527, -0.024473, -0.018428, -0.013958, -0.008161, -0.001196, 0.001754, -0.004016, -0.011132, -0.018325, -0.021813, -0.021514, -0.016948, -0.018061, -0.025702, -0.028671, -0.021470, -0.011028, -0.001934
	-0.059202, -0.050525, -0.065461, -0.076792, -0.084156, -0.088538, -0.090719, -0.096070, -0.105729, -0.105136, -0.090350, -0.083865, -0.087807, -0.086145, -0.074773, -0.064235, -0.057641, -0.055896, -0.051286, -0.046566, -0.042431, -0.034723, -0.023762, -0.014983, -0.009126, -0.004877, 0.000094, 0.003492, -0.000931, -0.005883, -0.011665, -0.015251, -0.016432, -0.016119, -0.015373, -0.018827, -0.019994, -0.017564, -0.012298, 0.002094
	-0.055561, -0.058184, -0.062669, -0.068111, -0.080741, -0.091895, -0.093911, -0.094387, -0.100239, -0.100695, -0.089841, -0.085682, -0.085212, -0.082910, -0.073072, -0.063594, -0.056157, -0.053482, -0.048107, -0.045405, -0.039982, -0.029777, -0.019905, -0.013872, -0.009732, -0.004272, 0.003500, 0.006909, 0.001302, -0.004626, -0.012374, -0.014751, -0.014637, -0.011794, -0.012913, -0.018244, -0.023377, -0.018086, -0.006575, 0.003294
	-0.062834, -0.047300, -0.060870, -0.073023, -0.079303, -0.082121, -0.083623, -0.091321, -0.100996, -0.098896, -0.085406, -0.078881, -0.081932, -0.082077, -0.074409, -0.063158, -0.053822, -0.050328, -0.045077, -0.039678, -0.035825, -0.028532, -0.017793, -0.009121, -0.003444, -0.000905, 0.003990, 0.007745, 0.004595, 0.000143, -0.004555, -0.007411, -0.010850, -0.010100, -0.010079, -0.013177, -0.016434, -0.014663, -0.010248, -0.000213
	-0.054748, -0.053907, -0.057576, -0.063118, -0.072478, -0.081366, -0.084424, -0.086348, -0.089718, -0.089305, -0.081771, -0.076889, -0.076923, -0.073518, -0.067973, -0.057643, -0.050848, -0.046966, -0.041560, -0.036436, -0.029233, -0.020685, -0.010240, -0.004935, -0.001084, 0.002478, 0.009168, 0.014038, 0.010885, 0.004752, -0.001650, -0.004209, -0.003998, -0.002336, -0.003784, -0.010930, -0.016480, -0.012798, -0.003650, 0.002998
	-0.059345, -0.041989, -0.057435, -0.068229, -0.072857, -0.072586, -0.075155, -0.083286, -0.091292, -0.089727, -0.073702, -0.068353, -0.072910, -0.073863, -0.065527, -0.053635, -0.046064, -0.043899, -0.037607, -0.031251, -0.026194, -0.018885, -0.008095, 0.000309, 0.004911, 0.007046, 0.010642, 0.015635, 0.015277, 0.012612, 0.008074, 0.004852, 0.001546, 0.000504, 0.000589, -0.002769, -0.006432, -0.007765, -0.005391, 0.006950
	-0.050324, -0.049088, -0.052417, -0.057257, -0.063818, -0.071057, -0.074636, -0.075459, -0.079445, -0.077368, -0.068788, -0.063940, -0.065040, -0.063419, -0.054864, -0.044910, -0.038774, -0.036951, -0.031149, -0.026080, -0.018383, -0.011985, -0.001732, 0.003893, 0.007180, 0.011120, 0.017429, 0.021738, 0.019167, 0.015812, 0.011027, 0.007243, 0.006720, 0.009346, 0.006598, -0.003776, -0.009199, -0.007592, 0.005481, 0.014396
	-0.058437, -0.035937, -0.050762, -0.060425, -0.061123, -0.059090, -0.062399, -0.072124, -0.080338, -0.074950, -0.060985, -0.054754, -0.059333, -0.060500, -0.051714, -0.038834, -0.031117, -0.031693, -0.025186, -0.017982, -0.014316, -0.010137, 0.000228, 0.008774, 0.014018, 0.016470, 0.019918, 0.022071, 0.021109, 0.019957, 0.018698, 0.015803, 0.013135, 0.011136, 0.008719, 0.003522, -0.000994, 0.000525, 0.006297, 0.018454
	-0.046143, -0.041577, -0.045391, -0.046668, -0.051722, -0.057607, -0.062802, -0.065205, -0.068243, -0.066293, -0.058216, -0.051324, -0.051806, -0.051018, -0.043393, -0.032431, -0.024016, -0.023321, -0.018504, -0.013897, -0.008455, -0.001123, 0.006609, 0.010462, 0.013887, 0.019328, 0.024804, 0.026590, 0.023420, 0.020337, 0.017129, 0.017199, 0.016391, 0.015616, 0.013257, 0.005832, -0.000019, 0.003462, 0.014308, 0.023624
	-0.051989, -0.030294, -0.043380, -0.051339, -0.050711, -0.048193, -0.052258, -0.061218, -0.070507, -0.068810, -0.049476, -0.042352, -0.046018, -0.046673, -0.038670, -0.027263, -0.018137, -0.018587, -0.013603, -0.008482, -0.004647, -0.000011, 0.008230, 0.015652, 0.019436, 0.023069, 0.024762, 0.027750, 0.028115, 0.026227, 0.022220, 0.023166, 0.020341, 0.018455, 0.014918, 0.011932, 0.007138, 0.008523, 0.014718, 0.026201
	-0.041448, -0.035286, -0.036538, -0.037577, -0.044652, -0.049300, -0.051092, -0.052841, -0.058068, -0.056947, -0.046235, -0.038436, -0.037494, -0.034175, -0.028932, -0.016904, -0.010075, -0.010552, -0.004464, -0.001243, 0.003236, 0.010200, 0.015604, 0.020362, 0.023157, 0.028023, 0.032826, 0.035958, 0.034819, 0.030600, 0.025988, 0.026013, 0.026284, 0.025661, 0.022322, 0.013336, 0.006464, 0.011312, 0.022330, 0.031668
	-0.048540, -0.022534, -0.035260, -0.042156, -0.042749, -0.037408, -0.038818, -0.047322, -0.056808, -0.053643, -0.035691, -0.027822, -0.028789, -0.028255, -0.020274, -0.007285, -0.000723, -0.000788, 0.005440, 0.008938, 0.008953, 0.012074, 0.017957, 0.025241, 0.029175, 0.032057, 0.033733, 0.038359, 0.039349, 0.037161, 0.034052, 0.034585, 0.032020, 0.029940, 0.026326, 0.024577, 0.020432, 0.021586, 0.024568, 0.034552
	-0.033086, -0.027982, -0.029443, -0.029011, -0.035629, -0.040579, -0.038290, -0.037389, -0.041260, -0.040430, -0.032279, -0.021394, -0.018817, -0.015525, -0.007558, 0.006345, 0.011048, 0.011271, 0.013497, 0.017030, 0.017449, 0.022752, 0.026764, 0.030722, 0.033532, 0.037203, 0.043356, 0.048536, 0.047776, 0.043851, 0.039311, 0.039944, 0.039954, 0.038931, 0.034893, 0.030946, 0.023127, 0.027359, 0.034859, 0.043920
	-0.036218, -0.016846, -0.030897, -0.036980, -0.037261, -0.033334, -0.030888, -0.034074, -0.042142, -0.039980, -0.021377, -0.013603, -0.014171, -0.013131, -0.001768, 0.014998, 0.020060, 0.018173, 0.019934, 0.024704, 0.023739, 0.024617, 0.027288, 0.035116, 0.041187, 0.043128, 0.045921, 0.051709, 0.053031, 0.050698, 0.047697, 0.047728, 0.046845, 0.043201, 0.041805, 0.040728, 0.036184, 0.034435, 0.035120, 0.045329
	-0.029808, -0.023871, -0.026541, -0.026705, -0.031203, -0.036908, -0.034411, -0.029231, -0.028090, -0.026102, -0.016691, -0.007747, -0.004471, 0.001560, 0.010738, 0.025062, 0.027672, 0.024833, 0.026976, 0.029502, 0.030754, 0.035709, 0.039403, 0.044719, 0.046379, 0.049250, 0.054178, 0.059793, 0.059542, 0.052111, 0.047608, 0.050103, 0.053142, 0.052747, 0.050045, 0.044102, 0.033149, 0.035392, 0.045678, 0.054080
	-0.032238, -0.008993, -0.023999, -0.030969, -0.028658, -0.024887, -0.024493, -0.028088, -0.031053, -0.022849, -0.003868, 0.004647, 0.004540, 0.007560, 0.018373, 0.031401, 0.035778, 0.033768, 0.035173, 0.035884, 0.036597, 0.038940, 0.044566, 0.053914, 0.056554, 0.056382, 0.056449, 0.060387, 0.062696, 0.058223, 0.055016, 0.056193, 0.056891, 0.052793, 0.052741, 0.052626, 0.048117, 0.045032, 0.048033, 0.055100
	-0.019758, -0.015110, -0.017814, -0.018871, -0.023340, -0.028653, -0.026880, -0.018681, -0.017020, -0.011343, -0.001002, 0.008249, 0.014012, 0.020367, 0.026878, 0.038534, 0.041827, 0.039532, 0.039775, 0.039109, 0.043172, 0.049325, 0.056604, 0.059583, 0.059329, 0.059876, 0.062766, 0.068759, 0.067214, 0.059657, 0.055950, 0.056798, 0.058619, 0.058591, 0.059849, 0.056473, 0.046841, 0.047921, 0.058342, 0.065346
	-0.018628, -0.000296, -0.014764, -0.022634, -0.020483, -0.016362, -0.015485, -0.017352, -0.020246, -0.010362, 0.008635, 0.018414, 0.018542, 0.024258, 0.033370, 0.045728, 0.049983, 0.044610, 0.044638, 0.047649, 0.049220, 0.051954, 0.058932, 0.065915, 0.069102, 0.067410, 0.067680, 0.073734, 0.072203, 0.067293, 0.063945, 0.064378, 0.065047, 0.061989, 0.062882, 0.063468, 0.059707, 0.057986, 0.059739, 0.066139
	-0.010091, -0.006551, -0.008018, -0.009589, -0.016068, -0.020662, -0.019451, -0.010985, -0.009391, -0.003580, 0.007826, 0.019598, 0.024961, 0.033762, 0.040618, 0.050868, 0.052139, 0.050495, 0.049198, 0.051777, 0.056840, 0.061771, 0.068414, 0.072295, 0.073443, 0.072145, 0.073414, 0.079338, 0.075988, 0.067367, 0.064745, 0.064435, 0.066982, 0.065811, 0.067424, 0.063230, 0.058438, 0.059982, 0.067672, 0.072460
	-0.016254, 0.006291, -0.008031, -0.013944, -0.014475, -0.010741, -0.009932, -0.011709, -0.015503, -0.006971, 0.013190, 0.024865, 0.029121, 0.033942, 0.044335, 0.054572, 0.058078, 0.055224, 0.055897, 0.058327, 0.061207, 0.063939, 0.070506, 0.078141, 0.084203, 0.081223, 0.079519, 0.082883, 0.080890, 0.076174, 0.071279, 0.073064, 0.071225, 0.066859, 0.069860, 0.070836, 0.069427, 0.069140, 0.070950, 0.075269
	-0.008127, 0.000730, 0.001164, -0.000308, -0.006659, -0.012343, -0.011463, -0.003755, -0.001876, 0.005166, 0.016616, 0.030243, 0.036509, 0.045020, 0.053681, 0.063738, 0.066425, 0.063964, 0.062796, 0.065633, 0.071912, 0.077280, 0.082580, 0.086477, 0.089798, 0.089603, 0.091453, 0.096125, 0.088708, 0.079903, 0.074317, 0.076190, 0.075399, 0.075242, 0.079628, 0.077855, 0.071473, 0.073702, 0.082757, 0.088086
	-0.010951, 0.013218, -0.000878, -0.006241, -0.005623, 0.000046, 0.000158, -0.002943, -0.005314, 0.005491, 0.026890, 0.035754, 0.041490, 0.045829, 0.059325, 0.070249, 0.074114, 0.071815, 0.073229, 0.076313, 0.080778, 0.081554, 0.087919, 0.096206, 0.101562, 0.101674, 0.100494, 0.103989, 0.100292, 0.093977, 0.088080, 0.088136, 0.086555, 0.081494, 0.084966, 0.087073, 0.084113, 0.085184, 0.087700, 0.092188
	-0.002972, 0.006020, 0.006098, 0.004303, 0.001326, -0.002386, -0.001840, 0.005325, 0.008624, 0.016246, 0.026781, 0.039696, 0.048540, 0.055938, 0.066982, 0.076497, 0.080828, 0.079669, 0.080127, 0.083754, 0.089783, 0.093456, 0.100570, 0.105322, 0.107132, 0.110571, 0.113141, 0.118064, 0.111721, 0.101634, 0.093555, 0.093112, 0.093104, 0.092325, 0.094780, 0.092552, 0.085283, 0.088882, 0.097508, 0.105280
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 11.4
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity

[bed_mesh Preperations]
version = 1
points = 
	0.012158, -0.006098, -0.020628, -0.034069, -0.049418, -0.058491, -0.062706, -0.063181, -0.065552, -0.063461, -0.057373, -0.056717, -0.056579, -0.054080, -0.053373, -0.056878, -0.057281, -0.055224, -0.049676, -0.047605, -0.041454, -0.034605, -0.022490, -0.011292, -0.009411, -0.005344, -0.003510, -0.002717, -0.005999, -0.010712, -0.013141, -0.015611, -0.020004, -0.017667, -0.016629, -0.022248, -0.024864, -0.024065, -0.014921, -0.010826
	-0.005958, -0.021084, -0.033800, -0.047903, -0.059950, -0.071345, -0.072502, -0.073350, -0.075852, -0.072963, -0.067236, -0.064315, -0.065698, -0.064338, -0.062871, -0.065238, -0.067095, -0.063584, -0.059241, -0.057846, -0.051380, -0.043157, -0.030230, -0.019950, -0.018121, -0.014291, -0.009354, -0.013065, -0.016464, -0.022925, -0.025337, -0.026541, -0.030577, -0.029068, -0.027094, -0.030532, -0.034241, -0.032625, -0.021498, -0.020513
	-0.017526, -0.027763, -0.040710, -0.055305, -0.068172, -0.079641, -0.081247, -0.081903, -0.083679, -0.081855, -0.073270, -0.070340, -0.072083, -0.071536, -0.066055, -0.065901, -0.069085, -0.066531, -0.063284, -0.061616, -0.053366, -0.047292, -0.035451, -0.023167, -0.022205, -0.016699, -0.012552, -0.014153, -0.018802, -0.030443, -0.032210, -0.034051, -0.034437, -0.031439, -0.030406, -0.032817, -0.036351, -0.034849, -0.024250, -0.019489
	-0.017750, -0.030284, -0.043463, -0.055839, -0.071865, -0.084888, -0.086157, -0.084619, -0.086681, -0.084515, -0.075246, -0.073263, -0.075604, -0.075123, -0.069177, -0.070723, -0.071097, -0.068644, -0.065465, -0.063718, -0.057574, -0.049335, -0.036556, -0.028418, -0.028259, -0.023387, -0.018454, -0.020519, -0.027499, -0.038314, -0.041534, -0.041886, -0.039972, -0.036438, -0.033959, -0.033009, -0.038291, -0.036339, -0.022688, -0.024783
	-0.021354, -0.034103, -0.047541, -0.060551, -0.075691, -0.089373, -0.092241, -0.091621, -0.093203, -0.090723, -0.082480, -0.079781, -0.079706, -0.079674, -0.074365, -0.073780, -0.073465, -0.070165, -0.064970, -0.065503, -0.059104, -0.051038, -0.041817, -0.031243, -0.031386, -0.028837, -0.023658, -0.024237, -0.029641, -0.039210, -0.042766, -0.044461, -0.041863, -0.039075, -0.034881, -0.034571, -0.039386, -0.038253, -0.031659, -0.024202
	-0.027696, -0.041184, -0.054054, -0.064759, -0.080898, -0.094964, -0.097906, -0.098033, -0.101256, -0.098300, -0.091517, -0.088420, -0.086945, -0.085220, -0.079938, -0.079979, -0.079828, -0.074842, -0.072903, -0.072415, -0.065384, -0.057454, -0.048482, -0.040977, -0.039336, -0.036065, -0.032553, -0.034336, -0.039337, -0.046271, -0.049398, -0.051220, -0.049530, -0.045000, -0.045029, -0.042100, -0.049767, -0.046386, -0.035574, -0.032188
	-0.033426, -0.046259, -0.059363, -0.068024, -0.084858, -0.097009, -0.103434, -0.106215, -0.107319, -0.106178, -0.100333, -0.097536, -0.095352, -0.091322, -0.086332, -0.082309, -0.081440, -0.078413, -0.075067, -0.073134, -0.068255, -0.062667, -0.054300, -0.046004, -0.042001, -0.039181, -0.035010, -0.036092, -0.041599, -0.048788, -0.051751, -0.051179, -0.051019, -0.049121, -0.045860, -0.046756, -0.050005, -0.051613, -0.040237, -0.035349
	-0.037931, -0.051993, -0.066455, -0.075044, -0.088177, -0.102890, -0.108223, -0.112373, -0.115787, -0.113421, -0.108543, -0.105936, -0.101048, -0.096863, -0.090726, -0.087882, -0.086665, -0.083874, -0.081096, -0.080894, -0.075125, -0.071038, -0.063072, -0.054696, -0.051039, -0.046728, -0.042566, -0.043887, -0.048745, -0.056834, -0.059808, -0.060521, -0.060664, -0.057968, -0.056317, -0.052477, -0.058814, -0.055877, -0.046325, -0.042545
	-0.041429, -0.053634, -0.067633, -0.077111, -0.090998, -0.103561, -0.109445, -0.114741, -0.120075, -0.119821, -0.114703, -0.110411, -0.105589, -0.099826, -0.093730, -0.089705, -0.087199, -0.086439, -0.082688, -0.082221, -0.078348, -0.073203, -0.065273, -0.058731, -0.054025, -0.049231, -0.044830, -0.043830, -0.045839, -0.054137, -0.059075, -0.059515, -0.058546, -0.056956, -0.054145, -0.053129, -0.056587, -0.056341, -0.047057, -0.039936
	-0.044295, -0.058972, -0.072101, -0.082726, -0.095001, -0.106449, -0.111505, -0.118363, -0.124608, -0.123506, -0.120263, -0.115400, -0.110227, -0.104535, -0.100348, -0.095757, -0.092961, -0.092377, -0.089613, -0.088047, -0.084834, -0.079314, -0.072500, -0.064519, -0.060449, -0.055767, -0.051803, -0.050997, -0.052855, -0.058115, -0.063348, -0.065363, -0.067936, -0.063474, -0.061475, -0.054726, -0.062529, -0.055352, -0.048878, -0.044991
	-0.045804, -0.056574, -0.073308, -0.082450, -0.097495, -0.107467, -0.111501, -0.116418, -0.126724, -0.125980, -0.123231, -0.120494, -0.114667, -0.111289, -0.103451, -0.099228, -0.095880, -0.095882, -0.093328, -0.091000, -0.087051, -0.081909, -0.075949, -0.064971, -0.061050, -0.055137, -0.049046, -0.047319, -0.049806, -0.056968, -0.059608, -0.060249, -0.063032, -0.060556, -0.056284, -0.056263, -0.058891, -0.057890, -0.051554, -0.042382
	-0.049818, -0.062681, -0.076305, -0.084328, -0.098717, -0.107866, -0.113937, -0.120088, -0.128622, -0.128931, -0.126353, -0.123191, -0.118529, -0.115642, -0.106288, -0.103976, -0.099708, -0.097750, -0.094501, -0.094545, -0.090910, -0.085952, -0.077352, -0.067196, -0.062435, -0.057738, -0.052934, -0.051098, -0.055294, -0.061112, -0.063120, -0.067525, -0.067979, -0.066558, -0.064608, -0.060597, -0.067812, -0.057641, -0.056224, -0.046471
	-0.050591, -0.060432, -0.075602, -0.083877, -0.096933, -0.106147, -0.112334, -0.118295, -0.127966, -0.128757, -0.125157, -0.121831, -0.118557, -0.116124, -0.108723, -0.104502, -0.099469, -0.095841, -0.090662, -0.089822, -0.087969, -0.084545, -0.076375, -0.064821, -0.059093, -0.053427, -0.047372, -0.044341, -0.047964, -0.054064, -0.057133, -0.059152, -0.061568, -0.059109, -0.056640, -0.056691, -0.056844, -0.054564, -0.048514, -0.040641
	-0.047704, -0.059564, -0.073127, -0.080945, -0.093764, -0.105483, -0.111501, -0.118792, -0.124812, -0.126576, -0.122064, -0.118087, -0.116126, -0.114867, -0.108053, -0.103336, -0.097558, -0.093250, -0.086537, -0.085303, -0.083677, -0.079292, -0.070542, -0.062526, -0.056818, -0.052534, -0.044035, -0.041353, -0.046942, -0.051329, -0.055481, -0.062777, -0.058499, -0.058025, -0.057390, -0.053562, -0.060843, -0.046555, -0.046260, -0.036083
	-0.046496, -0.052983, -0.067518, -0.076904, -0.091704, -0.103105, -0.111995, -0.117751, -0.122307, -0.122941, -0.118230, -0.115004, -0.114258, -0.113138, -0.105515, -0.098417, -0.093384, -0.090070, -0.083281, -0.079846, -0.078725, -0.075452, -0.066225, -0.057269, -0.053103, -0.047808, -0.039772, -0.036834, -0.041270, -0.047376, -0.051111, -0.053848, -0.053029, -0.050301, -0.048919, -0.050775, -0.050121, -0.046842, -0.039633, -0.030497
	-0.040695, -0.051685, -0.064038, -0.070974, -0.086679, -0.101773, -0.109889, -0.114373, -0.117883, -0.118764, -0.113125, -0.110931, -0.111099, -0.109664, -0.098733, -0.093182, -0.090154, -0.086213, -0.077214, -0.077108, -0.075555, -0.069117, -0.060704, -0.054093, -0.049253, -0.044799, -0.037536, -0.035304, -0.040134, -0.045456, -0.051720, -0.056675, -0.053743, -0.052923, -0.049701, -0.050238, -0.056776, -0.041485, -0.041755, -0.027329
	-0.039842, -0.039428, -0.055732, -0.063890, -0.079179, -0.092823, -0.101698, -0.106156, -0.111709, -0.113152, -0.108033, -0.104872, -0.105645, -0.103501, -0.094487, -0.087264, -0.084273, -0.080950, -0.074116, -0.070973, -0.068409, -0.062825, -0.054757, -0.044150, -0.040620, -0.036602, -0.031538, -0.026478, -0.031123, -0.037600, -0.042341, -0.046700, -0.047380, -0.042880, -0.040967, -0.045367, -0.044192, -0.038553, -0.029948, -0.020790
	-0.030596, -0.038279, -0.051528, -0.058981, -0.073983, -0.089044, -0.099173, -0.101740, -0.104830, -0.107083, -0.102306, -0.101554, -0.101336, -0.097146, -0.089217, -0.083800, -0.080621, -0.078071, -0.071535, -0.068328, -0.065806, -0.056882, -0.048683, -0.039756, -0.036349, -0.031328, -0.025351, -0.024133, -0.029773, -0.033858, -0.040011, -0.044146, -0.043900, -0.044797, -0.038019, -0.042319, -0.047297, -0.031851, -0.034318, -0.013527
	-0.032121, -0.034722, -0.047839, -0.054710, -0.069175, -0.084213, -0.094533, -0.097233, -0.100863, -0.104775, -0.099781, -0.097416, -0.098804, -0.096059, -0.086694, -0.079692, -0.076749, -0.074609, -0.068106, -0.063906, -0.061136, -0.055447, -0.045559, -0.035389, -0.029696, -0.025708, -0.020034, -0.017335, -0.022665, -0.028532, -0.032369, -0.035760, -0.037212, -0.035201, -0.032872, -0.034132, -0.035907, -0.032127, -0.025026, -0.009282
	-0.026707, -0.034374, -0.045183, -0.052691, -0.067014, -0.084964, -0.092286, -0.094441, -0.099291, -0.103609, -0.098278, -0.094972, -0.097169, -0.095394, -0.086653, -0.080205, -0.076284, -0.070594, -0.064535, -0.062012, -0.060174, -0.051216, -0.040622, -0.033396, -0.029636, -0.024235, -0.017274, -0.018232, -0.021459, -0.024778, -0.031754, -0.034481, -0.033398, -0.037949, -0.030432, -0.033219, -0.038432, -0.021975, -0.030052, -0.009295
	-0.028559, -0.029280, -0.042071, -0.048655, -0.061603, -0.076257, -0.086817, -0.091815, -0.095682, -0.098682, -0.093729, -0.091168, -0.092213, -0.090073, -0.084070, -0.077048, -0.072045, -0.066267, -0.060309, -0.053639, -0.051696, -0.046852, -0.034069, -0.025602, -0.020640, -0.018021, -0.013180, -0.009049, -0.013846, -0.018012, -0.021061, -0.024515, -0.027068, -0.026804, -0.024283, -0.025595, -0.028234, -0.025272, -0.019246, -0.008595
	-0.025711, -0.029003, -0.038836, -0.048015, -0.058511, -0.074480, -0.083738, -0.087945, -0.091439, -0.094310, -0.090288, -0.087858, -0.088589, -0.086163, -0.081829, -0.075146, -0.071136, -0.064399, -0.057338, -0.052103, -0.049650, -0.043210, -0.032998, -0.023124, -0.020191, -0.016625, -0.012433, -0.010465, -0.009871, -0.015007, -0.021217, -0.021582, -0.023800, -0.027652, -0.021527, -0.027137, -0.030828, -0.020152, -0.026202, -0.008568
	-0.031287, -0.022523, -0.035800, -0.041583, -0.052691, -0.065901, -0.075941, -0.079246, -0.083936, -0.086778, -0.082235, -0.078893, -0.080642, -0.079419, -0.074324, -0.067418, -0.062113, -0.057744, -0.049923, -0.043390, -0.040055, -0.035512, -0.023838, -0.015485, -0.009895, -0.008346, -0.005387, 0.001467, -0.000104, -0.003777, -0.007926, -0.012023, -0.013970, -0.014207, -0.013994, -0.017009, -0.019233, -0.019282, -0.014210, -0.001146
	-0.020719, -0.024043, -0.035160, -0.041635, -0.051902, -0.063884, -0.072884, -0.076738, -0.081856, -0.083761, -0.077857, -0.074651, -0.077952, -0.076310, -0.069721, -0.063240, -0.056775, -0.055188, -0.046711, -0.042996, -0.039499, -0.032268, -0.023129, -0.015735, -0.012305, -0.009383, -0.005789, -0.001996, -0.001166, -0.005106, -0.009634, -0.009864, -0.011905, -0.015913, -0.010246, -0.016645, -0.022975, -0.011972, -0.018524, 0.001048
	-0.026050, -0.019774, -0.032555, -0.037813, -0.044657, -0.054435, -0.065271, -0.071019, -0.075585, -0.077479, -0.072635, -0.069526, -0.071046, -0.070770, -0.063085, -0.055960, -0.050956, -0.049593, -0.042773, -0.034996, -0.032645, -0.029030, -0.020343, -0.011008, -0.005751, -0.003252, 0.000746, 0.003215, 0.001749, -0.000068, -0.001413, -0.002608, -0.005837, -0.007103, -0.008431, -0.012027, -0.015656, -0.014417, -0.006321, 0.003748
	-0.021728, -0.019178, -0.031232, -0.036249, -0.042206, -0.053190, -0.064017, -0.068545, -0.074597, -0.074544, -0.069543, -0.065779, -0.067928, -0.067354, -0.060655, -0.052790, -0.047723, -0.046044, -0.038188, -0.034539, -0.032080, -0.027152, -0.018902, -0.012508, -0.009304, -0.003955, -0.000288, -0.001549, -0.000556, -0.003756, -0.008467, -0.003851, -0.005999, -0.012959, -0.007423, -0.015332, -0.017388, -0.005695, -0.010807, 0.007710
	-0.028204, -0.017096, -0.027984, -0.032129, -0.038374, -0.046561, -0.059356, -0.061847, -0.069228, -0.070551, -0.065474, -0.059719, -0.059893, -0.060271, -0.053666, -0.047202, -0.041189, -0.039979, -0.033189, -0.028761, -0.025714, -0.021660, -0.014905, -0.007841, -0.004669, -0.001174, 0.001874, 0.005613, 0.005527, 0.001504, -0.000694, 0.001892, 0.001885, -0.002506, -0.005619, -0.007166, -0.009935, -0.007406, 0.000545, 0.009983
	-0.019393, -0.017785, -0.025482, -0.028146, -0.036861, -0.047528, -0.055696, -0.059118, -0.064151, -0.066346, -0.060565, -0.055661, -0.055495, -0.051944, -0.048147, -0.040645, -0.036359, -0.035990, -0.026764, -0.024843, -0.023572, -0.019648, -0.013807, -0.006811, -0.004589, -0.000266, 0.003010, 0.004931, 0.006834, 0.003254, -0.001690, 0.003120, 0.001036, -0.005283, 0.000659, -0.007399, -0.010996, -0.000832, -0.006381, 0.012135
	-0.021519, -0.010062, -0.018662, -0.023011, -0.029067, -0.036961, -0.043194, -0.048197, -0.053632, -0.055489, -0.050054, -0.045247, -0.042655, -0.040243, -0.034315, -0.027094, -0.022697, -0.021644, -0.015333, -0.010768, -0.013712, -0.012051, -0.005326, 0.000560, 0.005300, 0.007429, 0.009930, 0.015968, 0.016454, 0.012383, 0.010385, 0.011612, 0.011413, 0.008357, 0.006831, 0.005524, 0.003087, 0.003507, 0.009876, 0.018892
	-0.017331, -0.015238, -0.021971, -0.024651, -0.029507, -0.040209, -0.044232, -0.046101, -0.052689, -0.053151, -0.047133, -0.042985, -0.040475, -0.037020, -0.029999, -0.021348, -0.018232, -0.017876, -0.013058, -0.008535, -0.013279, -0.011527, -0.006296, -0.001615, 0.002270, 0.006991, 0.010272, 0.013407, 0.015950, 0.012503, 0.008026, 0.013701, 0.011513, 0.004867, 0.010667, 0.006774, 0.003571, 0.012416, 0.004875, 0.020961
	-0.022637, -0.011107, -0.018340, -0.023896, -0.028320, -0.038092, -0.041212, -0.041642, -0.044537, -0.046015, -0.041699, -0.035805, -0.033527, -0.030911, -0.022925, -0.010175, -0.007279, -0.008644, -0.005065, -0.000597, -0.003797, -0.004052, 0.000635, 0.006175, 0.010857, 0.012993, 0.016956, 0.022765, 0.023298, 0.020262, 0.018285, 0.019467, 0.021161, 0.018785, 0.017891, 0.017817, 0.013874, 0.012825, 0.015904, 0.025844
	-0.014532, -0.010189, -0.019385, -0.022584, -0.028159, -0.037803, -0.040566, -0.038125, -0.040339, -0.038899, -0.033171, -0.028143, -0.025641, -0.019755, -0.012463, -0.003824, -0.000871, -0.002698, -0.000197, 0.001952, -0.001353, -0.000188, 0.004902, 0.012600, 0.014373, 0.016449, 0.018872, 0.022822, 0.026385, 0.020681, 0.015275, 0.021387, 0.023535, 0.016733, 0.022161, 0.018819, 0.011276, 0.020785, 0.014683, 0.032409
	-0.016972, -0.004835, -0.015539, -0.019706, -0.022971, -0.032222, -0.037732, -0.035551, -0.033892, -0.031679, -0.024624, -0.019946, -0.016412, -0.010040, -0.003445, 0.005991, 0.008364, 0.006410, 0.008289, 0.009260, 0.007409, 0.008691, 0.015230, 0.022729, 0.025465, 0.025502, 0.026102, 0.030309, 0.031861, 0.026963, 0.024651, 0.027000, 0.029039, 0.025577, 0.027217, 0.027660, 0.023245, 0.021705, 0.026383, 0.034120
	-0.007042, -0.003943, -0.013314, -0.016082, -0.020497, -0.030911, -0.035096, -0.030889, -0.029351, -0.025337, -0.018980, -0.012449, -0.008879, -0.001902, 0.003577, 0.011256, 0.012460, 0.010502, 0.011904, 0.011483, 0.010067, 0.013356, 0.020792, 0.027368, 0.026382, 0.028554, 0.028164, 0.029993, 0.033232, 0.028830, 0.022354, 0.027991, 0.029607, 0.020011, 0.031066, 0.031755, 0.025061, 0.037228, 0.024607, 0.041453
	-0.012463, -0.000987, -0.008994, -0.014815, -0.017487, -0.026372, -0.031392, -0.028459, -0.025402, -0.024153, -0.015566, -0.007862, -0.004579, 0.001484, 0.010757, 0.017401, 0.019536, 0.016264, 0.016278, 0.018231, 0.018193, 0.018217, 0.025442, 0.034794, 0.036179, 0.034770, 0.033985, 0.040104, 0.040404, 0.034161, 0.030977, 0.032380, 0.034144, 0.031909, 0.033231, 0.035957, 0.034171, 0.033050, 0.038776, 0.042972
	-0.002758, 0.000700, -0.008467, -0.011525, -0.018705, -0.027522, -0.031609, -0.027494, -0.026315, -0.023221, -0.014164, -0.006562, -0.002205, 0.006453, 0.013689, 0.018647, 0.017673, 0.016751, 0.017380, 0.018782, 0.019038, 0.021992, 0.027475, 0.034748, 0.036870, 0.036635, 0.035394, 0.037519, 0.038008, 0.032063, 0.025834, 0.030409, 0.033142, 0.023991, 0.034882, 0.034323, 0.030317, 0.042711, 0.030793, 0.045129
	-0.011501, 0.004979, -0.003199, -0.009532, -0.013737, -0.022490, -0.028056, -0.025047, -0.023987, -0.021727, -0.011113, -0.003633, 0.003070, 0.010580, 0.020230, 0.025058, 0.026653, 0.024592, 0.024567, 0.025613, 0.027386, 0.029282, 0.037705, 0.042901, 0.046601, 0.045443, 0.044217, 0.048155, 0.045715, 0.039788, 0.034981, 0.038594, 0.038594, 0.034532, 0.038671, 0.042065, 0.040659, 0.042101, 0.045919, 0.050030
	-0.005239, 0.006624, -0.001837, -0.005350, -0.012024, -0.022230, -0.026144, -0.022704, -0.021559, -0.017450, -0.008515, 0.000433, 0.007392, 0.014546, 0.023538, 0.029043, 0.029892, 0.027280, 0.028785, 0.030662, 0.032758, 0.032649, 0.040035, 0.046372, 0.048654, 0.050330, 0.049538, 0.049746, 0.048851, 0.041068, 0.034598, 0.041375, 0.041379, 0.030621, 0.043091, 0.044712, 0.038634, 0.053475, 0.042814, 0.059369
	-0.011843, 0.005417, 0.000007, -0.005709, -0.011391, -0.019100, -0.024151, -0.021274, -0.019356, -0.016953, -0.004422, 0.002891, 0.010688, 0.018353, 0.027665, 0.035281, 0.036655, 0.034937, 0.036795, 0.039994, 0.042705, 0.042668, 0.048600, 0.055673, 0.059602, 0.061002, 0.059934, 0.064283, 0.061835, 0.052838, 0.048644, 0.048401, 0.048158, 0.044262, 0.049173, 0.053313, 0.050054, 0.051718, 0.058112, 0.062677
	-0.003249, 0.007140, -0.000190, -0.005182, -0.010664, -0.017472, -0.021072, -0.018928, -0.015929, -0.011810, -0.001170, 0.006999, 0.014346, 0.022026, 0.033087, 0.037703, 0.039304, 0.038986, 0.040531, 0.042739, 0.044912, 0.045850, 0.052980, 0.060894, 0.062495, 0.065477, 0.066306, 0.069035, 0.066301, 0.058359, 0.048879, 0.054660, 0.053906, 0.042834, 0.051292, 0.054304, 0.049390, 0.064968, 0.053062, 0.067337
x_count = 40
y_count = 40
mesh_x_pps = 2
mesh_y_pps = 2
algo = bicubic
tension = 0.2
min_x = 20.0
max_x = 480.0
min_y = 20.0
max_y = 480.0
ratos_mesh_version = 1
ratos_bed_temp = 80.0
ratos_mesh_kind = measured
ratos_beacon_probe_method = proximity
=======================
Config error
Traceback (most recent call last):
  File "/home/pi/klipper/klippy/klippy.py", line 130, in _connect
    self._read_config()
  File "/home/pi/klipper/klippy/klippy.py", line 123, in _read_config
    self.load_object(config, section_config.get_name(), None)
  File "/home/pi/klipper/klippy/klippy.py", line 112, in load_object
    self.objects[section] = init_func(config.getsection(section))
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 1766, in load_config
    return BedMesh(config)
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 107, in __init__
    self.splitter = MoveSplitter(config, self.gcode)
  File "/home/pi/klipper/klippy/extras/bed_mesh.py", line 1259, in __init__
    self.split_delta_z = config.getfloat(
  File "/home/pi/klipper/klippy/configfile.py", line 70, in getfloat
    return self._get_wrapper(self.fileconfig.getfloat, option, default,
  File "/home/pi/klipper/klippy/configfile.py", line 49, in _get_wrapper
    raise error("Option '%s' in section '%s' must have minimum of %s"
configparser.Error: Option 'split_delta_z' in section 'bed_mesh' must have minimum of 0.01
webhooks client 3975177936: New connection
webhooks client 3975177936: Client info {'program': 'Moonraker', 'version': 'v0.9.3-0-g71f9e67'}